Fast formation and growth of high-density Sn whiskers in Mg/Sn-based solder/Mg joints by ultrasonic-assisted soldering: Phenomena, mechanism and prevention

PubMed Central

Li, M. Y.; Yang, H. F.; Zhang, Z. H.; Gu, J. H.; Yang, S. H.

2016-01-01

A universally applicable method for promoting the fast formation and growth of high-density Sn whiskers on solders was developed by fabricating Mg/Sn-based solder/Mg joints using ultrasonic-assisted soldering at 250 °C for 6 s and then subjected to thermal aging at 25 °C for 7 d. The results showed that the use of the ultrasonic-assisted soldering could produce the supersaturated dissolution of Mg in the liquid Sn and lead to the existence of two forms of Mg in Sn after solidification. Moreover, the formation and growth of the high-density whiskers were facilitated by the specific contributions of both of the Mg forms in the solid Sn. Specifically, interstitial Mg can provide the persistent driving force for Sn whisker growth, whereas the Mg2Sn phase can increase the formation probability of Sn whiskers. In addition, we presented that the formation and growth of Sn whiskers in the Sn-based solders can be significantly restricted by a small amount of Zn addition (≥3 wt.%), and the prevention mechanisms are attributed to the segregation of Zn atoms at grain or phase boundaries and the formation of the lamellar-type Zn-rich structures in the solder. PMID:27273421

A label-free fluorescent aptamer sensor based on regulation of malachite green fluorescence

PubMed Central

Xu, Weichen; Lu, Yi

2009-01-01

We report a label-free fluorescent aptamer sensor for adenosine based on the regulation of malachite green (MG) fluorescence, with comparable sensitivity and selectivity to other labeled adenosine aptamer-based sensors. The sensor consists of free MG, an aptamer strand containing an adenosine aptamer next to an MG aptamer, and a bridging strand that partially hybridizes to the aptamer strand. Such a hybridization prevents MG from binding to MG aptamer, resulting in low fluorescence of MG in the absence of adenosine. Addition of adenosine causes the adenosine aptamer to bind adenosine, weakening the hybridization of the aptamer strand with the bridging strand, making it possible for MG to bind to the aptamer strand and exhibits high fluorescence intensity. Since this design is based purely on nucleic acid hybridization, it can be generally applied to other aptamers for the label-free detection of a broad range of analytes. PMID:20017558

Influence of Cu Addition on the Structure, Mechanical and Corrosion Properties of Cast Mg-2%Zn Alloy

NASA Astrophysics Data System (ADS)

Lotfpour, M.; Emamy, M.; Dehghanian, C.; Tavighi, K.

2017-05-01

Effects of different concentrations of Cu on the structure, mechanical and corrosion properties of Mg-2%Zn alloy were studied by the use of x-ray diffraction, optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, standard tensile testing, polarization and electrochemical impedance spectroscopy (EIS) measurements. The average grain size of the alloy decreased from above 1000 μm to about 200 μm with 5 wt.% Cu addition in as-cast condition. Microstructural studies revealed that Mg-2Zn- xCu alloys matrix typically consists of primary α-Mg and MgZnCu and Mg(Zn,Cu)2 intermetallics which are mainly found at the grain boundaries. The results obtained from mechanical testing ascertained that Cu addition increased the hardness values significantly. Although the addition of 0.5 wt.% Cu improved the ultimate tensile strength and elongation values, more Cu addition (i.e., 5 wt.%) weakened the tensile properties of the alloy by introducing semi-continuous network of brittle intermetallic phases. Based on polarization test results, it can be concluded that Cu eliminates a protective film on Mg-2%Zn alloy surface. Among Mg-2%Zn- x%Cu alloys, the one containing 0.1 wt.% Cu exhibited the best anti-corrosion property. However, further Cu addition increased the volume fraction of intermetallics culminating in corrosion rate enhancement due to the galvanic couple effect. EIS and microstructural analysis also confirmed the polarization results.

Magnesium-based energy storage systems and methods having improved electrolytes

DOEpatents

Liu, Tianbiao; Li, Guosheng; Liu, Jun; Shao, Yuyan

2016-12-20

Electrolytes for Mg-based energy storage devices can be formed from non-nucleophilic Mg.sup.2+ sources to provide outstanding electrochemical performance and improved electrophilic susceptibility compared to electrolytes employing nucleophilic sources. The instant electrolytes are characterized by high oxidation stability (up to 3.4 V vs Mg), improved electrophile compatibility and electrochemical reversibility (up to 100% coulombic efficiency). Synthesis of the Mg.sup.2+ electrolytes utilizes inexpensive and safe magnesium dihalides as non-nucleophilic Mg.sup.2+ sources in combination with Lewis acids, MR.sub.aX.sub.3-a (for 3.gtoreq.a.gtoreq.1). Furthermore, addition of free-halide-anion donors can improve the coulombic efficiency of Mg electrolytes from nucleophilic or non-nucleophilic Mg.sup.2+ sources.

In vitro inhibitory effects of plant-based foods and their combinations on intestinal α-glucosidase and pancreatic α-amylase

PubMed Central

2012-01-01

Background Plant-based foods have been used in traditional health systems to treat diabetes mellitus. The successful prevention of the onset of diabetes consists in controlling postprandial hyperglycemia by the inhibition of α-glucosidase and pancreatic α-amylase activities, resulting in aggressive delay of carbohydrate digestion to absorbable monosaccharide. In this study, five plant-based foods were investigated for intestinal α-glucosidase and pancreatic α-amylase. The combined inhibitory effects of plant-based foods were also evaluated. Preliminary phytochemical analysis of plant-based foods was performed in order to determine the total phenolic and flavonoid content. Methods The dried plants of Hibiscus sabdariffa (Roselle), Chrysanthemum indicum (chrysanthemum), Morus alba (mulberry), Aegle marmelos (bael), and Clitoria ternatea (butterfly pea) were extracted with distilled water and dried using spray drying process. The dried extracts were determined for the total phenolic and flavonoid content by using Folin-Ciocateu’s reagent and AlCl3 assay, respectively. The dried extract of plant-based food was further quantified with respect to intestinal α-glucosidase (maltase and sucrase) inhibition and pancreatic α-amylase inhibition by glucose oxidase method and dinitrosalicylic (DNS) reagent, respectively. Results The phytochemical analysis revealed that the total phenolic content of the dried extracts were in the range of 230.3-460.0 mg gallic acid equivalent/g dried extract. The dried extracts contained flavonoid in the range of 50.3-114.8 mg quercetin equivalent/g dried extract. It was noted that the IC50 values of chrysanthemum, mulberry and butterfly pea extracts were 4.24±0.12 mg/ml, 0.59±0.06 mg/ml, and 3.15±0.19 mg/ml, respectively. In addition, the IC50 values of chrysanthemum, mulberry and butterfly pea extracts against intestinal sucrase were 3.85±0.41 mg/ml, 0.94±0.11 mg/ml, and 4.41±0.15 mg/ml, respectively. Furthermore, the IC50 values of roselle and butterfly pea extracts against pancreatic α-amylase occurred at concentration of 3.52±0.15 mg/ml and 4.05±0.32 mg/ml, respectively. Combining roselle, chrysanthemum, and butterfly pea extracts with mulberry extract showed additive interaction on intestinal maltase inhibition. The results also demonstrated that the combination of chrysanthemum, mulberry, or bael extracts together with roselle extract produced synergistic inhibition, whereas roselle extract showed additive inhibition when combined with butterfly pea extract against pancreatic α-amylase. Conclusions The present study presents data from five plant-based foods evaluating the intestinal α-glucosidase and pancreatic α-amylase inhibitory activities and their additive and synergistic interactions. These results could be useful for developing functional foods by combination of plant-based foods for treatment and prevention of diabetes mellitus. PMID:22849553

Fabrication of Metallic Glass Powder for Brazing Paste for High-Temperature Thermoelectric Modules

NASA Astrophysics Data System (ADS)

Seo, Seung-Ho; Kim, Suk Jun; Lee, Soonil; Seo, Won-Seon; Kim, Il-Ho; Choi, Soon-Mok

2018-06-01

Metallic glass (MG) offers the advantage of outstanding oxidation resistance, since it has disordered atomic-scale structure without grain boundaries. We fabricated Al-based MG ribbons (Al84.5Y10Ni5.5) by a melt spinning process. We evaluated the adhesion strength of interfaces between the Al-based MG and a Ni-coated Cu electrode formed under various conditions at high temperature. In addition, we attempted to optimize the process conditions for pulverizing MG ribbons to < 100 micrometers by combining high-energy ball milling and planetary milling. We confirmed that the electrical resistivity of the Al-based MG ribbon was substantially reduced after annealing at high temperature (over 300°C) due to crystallization.

Evaluation of pristine and Eu ₂O₃-added MgB ₂ ceramics for medical applications: hardness, corrosion resistance, cytotoxicity and antibacterial activity.

PubMed

Batalu, Dan; Stanciuc, Ana Maria; Moldovan, Lucia; Aldica, Gheorghe; Badica, Petre

2014-09-01

Nano- or micropowders of Eu2O3 were added to MgB2, resulting in a composition of (MgB2)0.975(EuO1.5)0.025. Pristine and doped samples were prepared using spark plasma sintering and tested for (i) Vickers hardness, (ii) pH evolution in phosphate-buffered saline solution, (iii) corrosion resistance (Tafel polarization curves), (iv) cytotoxicity (in vitro tests), and (v) antibacterial activity. Eu2O3 addition influenced the investigated properties. Solutions of MgB2-based samples show a relatively high saturation pH of 8.5. This value is lower than that of solutions incubated with Mg or other Mg-based biodegradable alloys reported in the literature. MgB2-based samples have lower electro-corrosion rates than Mg. Their Vickers hardness is 6.8-10.2GPa, and these values are higher than those of biodegradable Mg-based alloys. MgB2 has low in vitro biocompatibility, good antibacterial activity against Escherichia coli, and mild activity against Staphylococcus aureus. Our results suggest that MgB2-based materials deserve attention in biomedical applications, such as implants or sterile medical instruments. Copyright © 2014 Elsevier B.V. All rights reserved.

Contribution of food additives to sodium and phosphorus content of diets rich in processed foods.

PubMed

Carrigan, Anna; Klinger, Andrew; Choquette, Suzanne S; Luzuriaga-McPherson, Alexandra; Bell, Emmy K; Darnell, Betty; Gutiérrez, Orlando M

2014-01-01

Phosphorus-based food additives increase the total phosphorus content of processed foods. However, the extent to which these additives augment total phosphorus intake per day is unclear. To examine the contribution of phosphorus-based food additives to the total phosphorus content of processed foods, separate 4-day menus for a low-additive and additive-enhanced diet were developed using Nutrition Data System for Research (NDSR) software. The low-additive diet was designed to conform to U.S. Department of Agriculture guidelines for energy and phosphorus intake (∼2,000 kcal/day and 900 mg of phosphorus per day), and it contained minimally processed foods. The additive-enhanced diet contained the same food items as the low-additive diet except that highly processed foods were substituted for minimally processed foods. Food items from both diets were collected, blended, and sent for measurement of energy and nutrient intake. The low-additive and additive-enhanced diet provided approximately 2,200 kcal, 700 mg of calcium, and 3,000 mg of potassium per day on average. Measured sodium and phosphorus content standardized per 100 mg of food was higher each day of the additive-enhanced diet as compared with the low-additive diet. When averaged over the 4 menu days, the measured phosphorus and sodium contents of the additive-enhanced diet were 606 ± 125 and 1,329 ± 642 mg higher than the low-additive diet, respectively, representing a 60% increase in total phosphorus and sodium content on average. When comparing the measured values of the additive-enhanced diet to NDSR-estimated values, there were no statistically significant differences in measured versus estimated phosphorus contents. Phosphorus and sodium additives in processed foods can substantially augment phosphorus and sodium intake, even in relatively healthy diets. Current dietary software may provide reasonable estimates of the phosphorus content in processed foods. Copyright © 2014 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Magnesium-based interventions for normal kidney function and chronic kidney disease.

PubMed

Massy, Ziad A; Nistor, Ionut; Apetrii, Mugurel; Brandenburg, Vincent M; Bover, Jordi; Evenepoel, Pieter; Goldsmith, David; Mazzaferro, Sandro; Urena-Torres, Pablo; Vervloet, Marc G; Cozzolino, Mario; Covic, Adrian; Era-Edta, On Behalf Of Ckd-Mbd Working Group Of

2016-04-01

Magnesium (Mg) is one of the most important cations in the body, playing an essential role in biological systems as co-factor for more than 300 essential enzymatic reactions. In the general population, low levels of Mg are associated with a high risk of cardio-vascular disease (CVD). Despite the accumulating literature data, the effect of Mg administration on mortality in chronic kidney disease (CKD) patients has never been investigated as a primary end-point. We conducted a systematic search of studies assessing the benefits and harms of Mg in CKD (stages 1 to 5 and 5D), and considered all randomized controlled trials (RCTs) and quasi-RCTs evaluating Mg-based interventions in CKD. As a phosphate binder, Mg salts offer a plausible opportunity for doubly favorable effects via reduction of intestinal phosphate absorption and addition of potentially beneficial effects via increasing circulating Mg levels. Mg supplementation might have a favorable effect on vascular calcification, although evidence for this is very slight. Although longitudinal data describe an association between low serum Mg levels and increased total and cardiovascular mortality, in patients with CKD, the existing RCTs reporting the effect of Mg supplementation on mortality failed to demonstrate any favorable effect. As with many other variables that influence hard end-points in nephrology, the role of Mg in CKD patients needs to be investigated in more depth. Additional research that is well-designed and directly targeting the role of Mg is needed as a consequence of limited existing evidence.

Coagulation-flocculation mechanisms in wastewater treatment plants through zeta potential measurements.

PubMed

López-Maldonado, E A; Oropeza-Guzman, M T; Jurado-Baizaval, J L; Ochoa-Terán, A

2014-08-30

Based on the polyelectrolyte-contaminant physical and chemical interactions at the molecular level, this article analyzed and discussed the coagulation-flocculation and chemical precipitation processes in order to improve their efficiency. Bench experiments indicate that water pH, polyelectrolyte (PE) dosing strategy and cationic polyelectrolyte addition are key parameters for the stability of metal-PE complexes. The coagulation-flocculation mechanism is proposed based on zeta potential (ζ) measurement as the criteria to define the electrostatic interaction between pollutants and coagulant-flocculant agents. Polyelectrolyte and wastewater dispersions are exposed to an electrophoretic effect to determine ζ. Finally, zeta potential values are compared at pH 9, suggesting the optimum coagulant dose at 162mg/L polydadmac and 67mg/L of flocculant, since a complete removal of TSS and turbidity is achieved. Based on the concentration of heavy metals (0.931mg/L Sn, 0.7mg/L Fe and 0.63mg/L Pb), treated water met the Mexican maximum permissible limits. In addition, the treated water has 45mg O2/L chemical oxygen demand (COD) and 45mg C/L total organic carbon (TOC). The coagulation-flocculation mechanism is proposed taking into account both: zeta potential (ζ)-pH measurement and chemical affinity, as the criteria to define the electrostatic and chemical interaction between pollutants and polyelectrolytes. Copyright © 2014 Elsevier B.V. All rights reserved.

In vitro regeneration and ploidy level analysis of Eulophia ochreata Lindl.

PubMed

Shriram, Varsha; Nanekar, Vikas; Kumar, Vinay; Kavi Kishor, P B

2014-11-01

Various parameters including explant-type, medium compositions, use of phytohormones and additives were optimized for direct and indirect regeneration of E. ochreata, a medicinal orchid under threat. Protocorm-like-bodies (PLBs) proved to be the best explants for shoot initiation, proliferation and callus induction. Murashige and Skoog's (MS) medium containing 2.5 mg L(-1) 6-benzylaminopurine (BAP), 1.0 mg L(-1) kinetin (Kin) and additives (adenine sulfate, arginine, citric acid, 30 mg L(-1) each and 50 mg L(-1) ascorbic acid) was optimal for shoot multiplication (12.1 shoots and 7.1 PLBs per explant with synchronized growth), which also produced callus. Shoot number was further increased with three successive subcultures on same media and approximately 40 shoots per explant were achieved after 3 cycles of 30 days each. Additives and casein hydrolysate (CH) showed advantageous effects on indirect shoot regeneration via protocorm-derived callus. Optimum indirect regeneration was achieved on MS containing additives, 500 mg L(-1) CH, 2.5 mg L(-1) BAP and 1.0 mg L(-1) Kin with 30 PLBs and 6 shoots per callus mass (approximately 5 mm size). The shoots were rooted (70% frequency) on one by fourth-MS medium containing 2.0 mg L(-1) indole-3-butyric acid, 200 mg L(-1) activated charcoal and additives. The rooted plantlets were hardened and transferred to greenhouse with 63% survival rate. Flow-cytometry based DNA content analysis revealed that the ploidy levels were maintained in in vitro regenerated plants. This is the first report for in vitro plant regeneration in E. ochreata.

Degradation Mechanisms of Magnesium Metal Anodes in Electrolytes Based on (CF 3SO 2) 2N – at High Current Densities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoo, Hyun Deog; Han, Sang-Don; Bolotin, Igor L.

The energy density of rechargeable batteries utilizing metals as anodes surpasses that of Li ion batteries, which employ carbon instead. Among possible metals, magnesium represents a potential alternative to the conventional choice, lithium, in terms of storage density, safety,stability, and cost. However, a major obstacle for metal-based batteries is the identification of electrolytes that show reversible deposition/dissolution of the metal anode and support reversible intercalation of ions into a cathode. Traditional Grignard-based Mg electrolytes are excellent with respect to the reversible deposition of Mg, but their limited anodic stability and compatibility with oxide cathodes hinder their applicability in Mg batteriesmore » with higher voltage. Non-Grignard electrolytes, which consist of ethereal solutions of magnesium(II) bis(trifluoromethanesulfonyl)imide (Mg(TFSI) 2), remain fairly stable near the potential of Mg deposition. The slight reactivity of these electrolytes toward Mg metal can be remedied by the addition of surface-protecting agents, such as MgCl 2. Hence, ethereal solutions of Mg(TFSI) 2 salt with MgCl 2 as an additive have been suggested as a representative non-Grignard Mg electrolyte. In this work, the degradation mechanisms of a Mg metal anode in the TFSI-based electrolyte were studied using a current density of 1 mA cm -2 and an areal capacity of ~0.4 mAh cm -2, which is close to those used in practical applications. The degradation mechanisms identified include the corrosion of Mg metal, which causes the loss of electronic pathways and mechanical integrity, the nonuniform deposition of Mg, and the decomposition of TFSI - anions. This study not only represents an assessment of the behavior of Mg metal anodes at practical current density and areal capacity but also details the outcomes of interfacial passivation, which was detected by simple cyclic voltammetry experiments. This study also points out the absolute absence of any passivation at the electrode-electrolyte interface for the premise of developing electrolytes compatible with a metal anode.« less

Degradation Mechanisms of Magnesium Metal Anodes in Electrolytes Based on (CF 3SO 2) 2N – at High Current Densities

DOE PAGES

Yoo, Hyun Deog; Han, Sang-Don; Bolotin, Igor L.; ...

2017-06-21

The energy density of rechargeable batteries utilizing metals as anodes surpasses that of Li ion batteries, which employ carbon instead. Among possible metals, magnesium represents a potential alternative to the conventional choice, lithium, in terms of storage density, safety,stability, and cost. However, a major obstacle for metal-based batteries is the identification of electrolytes that show reversible deposition/dissolution of the metal anode and support reversible intercalation of ions into a cathode. Traditional Grignard-based Mg electrolytes are excellent with respect to the reversible deposition of Mg, but their limited anodic stability and compatibility with oxide cathodes hinder their applicability in Mg batteriesmore » with higher voltage. Non-Grignard electrolytes, which consist of ethereal solutions of magnesium(II) bis(trifluoromethanesulfonyl)imide (Mg(TFSI) 2), remain fairly stable near the potential of Mg deposition. The slight reactivity of these electrolytes toward Mg metal can be remedied by the addition of surface-protecting agents, such as MgCl 2. Hence, ethereal solutions of Mg(TFSI) 2 salt with MgCl 2 as an additive have been suggested as a representative non-Grignard Mg electrolyte. In this work, the degradation mechanisms of a Mg metal anode in the TFSI-based electrolyte were studied using a current density of 1 mA cm -2 and an areal capacity of ~0.4 mAh cm -2, which is close to those used in practical applications. The degradation mechanisms identified include the corrosion of Mg metal, which causes the loss of electronic pathways and mechanical integrity, the nonuniform deposition of Mg, and the decomposition of TFSI - anions. This study not only represents an assessment of the behavior of Mg metal anodes at practical current density and areal capacity but also details the outcomes of interfacial passivation, which was detected by simple cyclic voltammetry experiments. This study also points out the absolute absence of any passivation at the electrode-electrolyte interface for the premise of developing electrolytes compatible with a metal anode.« less

Quasicrystal-reinforced Mg alloys

PubMed Central

Kyun Kim, Young; Tae Kim, Won; Hyang Kim, Do

2014-01-01

The formation of the icosahedral phase (I-phase) as a secondary solidification phase in Mg–Zn–Y and Mg–Zn–Al base systems provides useful advantages in designing high performance wrought magnesium alloys. The strengthening in two-phase composites (I-phase + α-Mg) can be explained by dispersion hardening due to the presence of I-phase particles and by the strong bonding property at the I-phase/matrix interface. The presence of an additional secondary solidification phase can further enhance formability and mechanical properties. In Mg–Zn–Y alloys, the co-presence of I and Ca2Mg6Zn3 phases by addition of Ca can significantly enhance formability, while in Mg–Zn–Al alloys, the co-presence of the I-phase and Mg2Sn phase leads to the enhancement of mechanical properties. Dynamic and static recrystallization are significantly accelerated by addition of Ca in Mg–Zn–Y alloy, resulting in much smaller grain size and more random texture. The high strength of Mg–Zn–Al–Sn alloys is attributed to the presence of finely distributed Mg2Sn and I-phase particles embedded in the α-Mg matrix. PMID:27877660

Cognitive fatigue in patients with myasthenia gravis.

PubMed

Jordan, Berit; Schweden, Tabea L K; Mehl, Theresa; Menge, Uwe; Zierz, Stephan

2017-09-01

Cognitive fatigue has frequently been reported in myasthenia gravis (MG). However, objective assessment of cognitive fatigability has never been evaluated. Thirty-three MG patients with stable generalized disease and 17 healthy controls underwent a test battery including repeated testing of attention and concentration (d2-R) and Paced Auditory Serial Addition Test. Fatigability was based on calculation of linear trend (LT) reflecting dynamic performance within subsequent constant time intervals. Additionally, fatigue questionnaires were used. MG patients showed a negative LT in second d2-R testing, indicating cognitive fatigability. This finding significantly differed from stable cognitive performance in controls (P < 0.05). Results of Paced Auditory Serial Addition Test testing did not differ between groups. Self-assessed fatigue was significantly higher in MG patients compared with controls (P < 0.001), but did not correlate with LT. LT quantifies cognitive fatigability as an objective measurement of performance decline in MG patients. Self-assessed cognitive fatigue is not correlated with objective findings. Muscle Nerve 56: 449-457, 2017. © 2016 Wiley Periodicals, Inc.

Research activities of biomedical magnesium alloys in China

NASA Astrophysics Data System (ADS)

Zheng, Yufeng; Gu, Xuenan

2011-04-01

The potential application of Mg alloys as bioabsorable/biodegradable implants have attracted much recent attention in China. Advances in the design and biocompatibility evaluation of bio-Mg alloys in China are reviewed in this paper. Bio-Mg alloys have been developed by alloying with the trace elements existing in human body, such as Mg-Ca, Mg-Zn and Mg-Si based systems. Additionally, novel structured Mg alloys such as porous, composited, nanocrystalline and bulk metallic glass alloys were tried. To control the biocorrosion rate of bio-Mg implant to match the self-healing/regeneration rate of the surrounding tissue in vivo, surface modification layers were coated with physical and chemical methods.

Agile Thermal Management STT-RX. Catalytic Influence of Ni-based Additives on the Dehydrogentation Properties of Ball Milled MgH2 (PREPRINT)

DTIC Science & Technology

2011-12-01

Wronski: Particle size, grain size and gamma-MgH2 effects on the desorption properties of nanocrystal- line commercial magnesium hydride processed...Catalytic effects of various forms of nickel on the synthesis rate and hydrogen desorption properties of nanocrystalline magnesium hydride (MgH2...dehydrogenation reaction. 15. SUBJECT TERMS magnesium hydride , MgH, thermal energy storage materials, endothermic reaction 16. SECURITY CLASSIFICATION

Enhanced corrosion resistance and cytocompatibility of biodegradable Mg alloys by introduction of Mg(OH)2 particles into poly (L-lactic acid) coating

PubMed Central

Shi, Yong-juan; Pei, Jia; Zhang, Jian; Niu, Jia-lin; Zhang, Hua; Guo, Sheng-rong; Li, Zhong-hua; Yuan, Guang-yin

2017-01-01

A strategy of suppressing the fast degradation behaviour of Mg-based biomaterials by the introduction of one of Mg degradation products Mg(OH)2 was proposed according to the following degradation mechanism, Mg + 2H2O ⇋ Mg(OH)2 + H2↑. Specifically, Mg(OH)2 submicron particles were mixed into poly (L-lactic acid) (PLLA) to synthesize a composite coating onto hydrofluoric acid-pretreated Mg-Nd-Zn-Zr alloy. The in vitro degradation investigations showed that the addition of Mg(OH)2 particles not only slowed down the corrosion of Mg matrix, but also retarded the formation of gas pockets underneath the polymer coating. Correspondingly, cytocompatibility results exhibited significant improvement of proliferation of endothelial cells, and further insights was gained into the mechanisms how the introduction of Mg(OH)2 particles into PLLA coating affected the magnesium alloy degradation and cytocompatibility. The present study provided a promising surface modification strategy to tailor the degradation behaviour of Mg-based biomaterials. PMID:28150751

Determination of biogenic amines in chocolate by ion chromatographic separation and pulsed integrated amperometric detection with implemented wave-form at Au disposable electrode.

PubMed

Pastore, Paolo; Favaro, Gabriella; Badocco, Denis; Tapparo, Andrea; Cavalli, Silvano; Saccani, Giovanna

2005-12-09

A rapid and selective cation exchange chromatographic method coupled to integrated pulsed amperometric detection (PAD) has been developed to quantify biogenic amines in chocolate. The method is based on gradient elution of aqueous methanesulfonic acid with post column addition of strong base to obtain suitable conditions for amperometric detection. A potential waveform able to keep long time performance of the Au disposable electrode was set up. Total analysis time is less than 20min. Concentration levels of dopamine, serotonin, tyramine, histamine and 2-phenylethylamine were measured, after extraction with perchloric acid from 2g samples previously defatted twice with petroleum ether. The method was used to determine the analytes in chocolate real matrices and their quantification was made with standard addition method. Only dopamine, histamine and serotonin were found in the analysed real samples. Repeatabilities of their signals, computed on their amounts in the real samples, were 5% for all of them. Repeatabilities of tyramine and phenethylamine were relative to standard additions to real samples (close to 1mg/l in the extract) and were 7 and 3%, respectively. Detection limits were computed with the 3s of the baseline noise combined with the calibration plot regression parameters. They were satisfactorily low for all amines: 3mg/kg for dopamine, 2mg/kg for tyramine, 1mg/kg for histamine, 2mg/kg for serotonin, 3mg/kg for 2-phenylethylamine.

Application of computational thermodynamics in the study of magnsium alloys and bulk metallic glasses

NASA Astrophysics Data System (ADS)

Cao, Hongbo

In this thesis, the application of the computational thermodynamics has been explored on two subjects, the study of magnesium alloys (Chapter 1-5) and bulk metallic glasses (BMGs) (Chapter 6-9). For the former case, a strategy of experiments coupled with the CALPHAD approach was employed to establish a thermodynamic description of the quaternary system Mg-Al-Ca-Sr focusing on the Mg-rich phase equilibria. Multicomponent Mg-rich alloys based on the MgAl-Ca-Sr system are one of the most promising candidates for the high temperature applications in the transportation industry. The Mg-Al-Ca-Sr quaternary consists of four ternaries and six binaries. Thermodynamic descriptions of all constituent binaries are available in the literature. Thermodynamic descriptions of the two key ternaries, Mg-Al-Sr and Mg-Al-Ca, were obtained by an efficient and reliable methodology, combining computational thermodynamics with key experiments. The obtained thermodynamic descriptions were validated by performing extensive comparisons between the calculations and experimental information. Thermodynamic descriptions of the other two ternaries, MgCa-Sr and Al-Ca-Sr, were obtained by extrapolation. For the later case, a computational thermodynamic strategy was formulated to obtain a minor but optimum amount of additional element into a base alloy to improve its glass forming ability (GFA). This was done through thermodynamically calculating the maximum liquidus depressions caused by various alloying addition (or replacement) schemes. The success of this approach has been examined in two multicomponent systems, Zr-based Zr-Cu-Ni-Al-Ti and Cu-rich Cu-Zr-Ti-Y. For both cases, experimental results showed conclusively that the GFA increases more than 100% from the base alloy to the one with minor but optimal elemental addition. Furthermore, a thermodynamic computational approach was employed to identify the compositions of Zr-Ti-Ni-Cu-Al alloys exhibiting low-lying liquidus surfaces, which tend to favor the BMG formation. Guided by these calculations, several series of new Zr-based alloys with excellent GFA were synthesized. The approach using the thermodynamically calculated liquidus temperatures was proved to be robust in locating BMGs and can be considered as a universal method to predict novel BMGs not only of scientific interest but also potential technological applications.

Friction Stir Additive Manufacturing: Route to High Structural Performance

NASA Astrophysics Data System (ADS)

Palanivel, S.; Sidhar, H.; Mishra, R. S.

2015-03-01

Aerospace and automotive industries provide the next big opportunities for additive manufacturing. Currently, the additive industry is confronted with four major challenges that have been identified in this article. These challenges need to be addressed for the additive technologies to march into new frontiers and create additional markets. Specific potential success in the transportation sectors is dependent on the ability to manufacture complicated structures with high performance. Most of the techniques used for metal-based additive manufacturing are fusion based because of their ability to fulfill the computer-aided design to component vision. Although these techniques aid in fabrication of complex shapes, achieving high structural performance is a key problem due to the liquid-solid phase transformation. In this article, friction stir additive manufacturing (FSAM) is shown as a potential solid-state process for attaining high-performance lightweight alloys for simpler geometrical applications. To illustrate FSAM as a high-performance route, manufactured builds of Mg-4Y-3Nd and AA5083 are shown as examples. In the Mg-based alloy, an average hardness of 120 HV was achieved in the built structure and was significantly higher than that of the base material (97 HV). Similarly for the Al-based alloy, compared with the base hardness of 88 HV, the average built hardness was 104 HV. A potential application of FSAM is illustrated by taking an example of a simple stiffener assembly.

Effects of CH3OH Addition on Plasma Electrolytic Oxidation of AZ31 Magnesium Alloys

NASA Astrophysics Data System (ADS)

He, Yongyi; Chen, Li; Yan, Zongcheng; Zhang, Yalei

2015-09-01

Plasma electrolytic oxidation (PEO) films on AZ31 magnesium alloys were prepared in alkaline silicate electrolytes (base electrolyte) with the addition of different volume concentrations of CH3OH, which was used to adjust the thickness of the vapor sheath. The compositions, morphologies, and thicknesses of ceramic layers formed with different CH3OH concentrations were determined via X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS), and scanning electron microscopy (SEM). Corrosion behavior of the oxide films was evaluated in 3.5 wt.% NaCl solution using potentiodynamic polarization tests. PEO coatings mainly comprised Mg, MgO, and Mg2SiO4. The addition of CH3OH in base electrolytes affected the thickness, pores diameter, and Mg2SiO4 content in the films. The films formed in the electrolyte containing 12% CH3OH exhibited the highest thickness. The coatings formed in the electrolyte containing different concentrations of CH3OH exhibited similar corrosion resistance. The energy consumption of PEO markedly decreased upon the addition of CH3OH to the electrolytes. The result is helpful for energy saving in the PEO process. supported by National Natural Science Foundation of China (No. 21376088), the Project of Production, Education and Research, Guangdong Province and Ministry of Education (Nos. 2012B09100063, 2012A090300015), and Guangzhou Science and Technology Plan Projects of China (No. 2014Y2-00042)

Effect of platelet-shaped graphene additives on actuating response of carbon nanotube/ionic liquid/polymer composite actuators

NASA Astrophysics Data System (ADS)

Monobe, Hirosato; Tsuchiya, Nobuyuki; Yamamura, Masahiro; Mukai, Ken; Sugino, Takushi; Asaka, Kinji

2018-03-01

In this study, the platelet-shaped graphene was used as a conductive additive in porous electrodes of a dry-type polymer actuator consisting of carbon nanotube (CNT), ionic liquid, and a base polymer to improve actuation properties. The generated strain was estimated from the bending motion of the actuator in the frequency range from 0.005 to 10 Hz. Ten different types of electrode film were prepared by changing the mixing amounts and surface areas of the platelet-shaped graphene. When a small amount of graphene (30 mg) relative to CNT (50 mg) was added to the CNT electrode, the strain was increased to be almost twice larger than that of CNT (50 mg) without any additives. The strain coefficient of the three-layered actuator with CNT electrodes with graphene additives is positively correlated with the capacitance per volume of such electrodes.

Tuning the Reversibility of Mg Anodes via Controlled Surface Passivation by H 2O/Cl – in Organic Electrolytes

DOE PAGES

Connell, Justin G.; Genorio, Bostjan; Lopes, Pietro Papa; ...

2016-10-17

Developing a new generation of battery chemistries is a critical challenge to moving beyond current Li-ion technologies. In this work, we introduce a surface-science-based approach for understanding the complex phenomena controlling the reversibility of Mg anodes for Mg-ion batteries. In addition, we identify the profound impact of trace levels of H 2O (≤3 ppm) on the kinetics of Mg deposition and determine that passive films of MgO and Mg(OH) 2 are formed only after Mg deposition ceases, rather than continuously during Mg reduction. We also find that Cl – inhibits passivation through the formation of adsorbed Cl – (Mg–Cl(ad)) and/ormore » MgCl 2 on the surface, as well as through a dynamic competition with H 2O in the double layer. In conclusion, this surface-science-based approach goes well beyond Mg anodes, highlighting the need for more in-depth understanding of electrolyte chemistries before a new generation of efficient and reversible battery technologies can be realized.« less

Controlling the corrosion and cathodic activation of magnesium via microalloying additions of Ge

PubMed Central

Liu, R. L.; Hurley, M. F.; Kvryan, A.; Williams, G.; Scully, J. R.; Birbilis, N.

2016-01-01

The evolution of corrosion morphology and kinetics for magnesium (Mg) have been demonstrated to be influenced by cathodic activation, which implies that the rate of the cathodic partial reaction is enhanced as a result of anodic dissolution. This phenomenon was recently demonstrated to be moderated by the use of arsenic (As) alloying as a poison for the cathodic reaction, leading to significantly improved corrosion resistance. The pursuit of alternatives to toxic As is important as a means to imparting a technologically safe and effective corrosion control method for Mg (and its alloys). In this work, Mg was microalloyed with germanium (Ge), with the aim of improving corrosion resistance by retarding cathodic activation. Based on a combined analysis herein, we report that Ge is potent in supressing the cathodic hydrogen evolution reaction (reduction of water) upon Mg, improving corrosion resistance. With the addition of Ge, cathodic activation of Mg subject to cyclic polarisation was also hindered, with beneficial implications for future Mg electrodes. PMID:27350286

Mechanical properties, in vitro corrosion and biocompatibility of newly developed biodegradable Mg-Zr-Sr-Ho alloys for biomedical applications

PubMed Central

Ding, Yunfei; Lin, Jixing; Wen, Cuie; Zhang, Dongmei; Li, Yuncang

2016-01-01

Our previous studies have demonstrated that Mg-Zr-Sr alloys can be anticipated as excellent biodegradable implant materials for load-bearing applications. In general, rare earth elements (REEs) are widely used in magnesium (Mg) alloys with the aim of enhancing the mechanical properties of Mg-based alloys. In this study, the REE holmium (Ho) was added to an Mg-1Zr-2Sr alloy at different concentrations of Mg1Zr2SrxHo alloys (x = 0, 1, 3, 5 wt. %) and the microstructure, mechanical properties, degradation behaviour and biocompatibility of the alloys were systematically investigated. The results indicate that the addition of Ho to Mg1Zr2Sr led to the formation of the intermetallic phases MgHo3, Mg2Ho and Mg17Sr2 which resulted in enhanced mechanical strength and decreased degradation rates of the Mg-Zr-Sr-Ho alloys. Furthermore, Ho addition (≤5 wt. %) to Mg-Zr-Sr alloys led to enhancement of cell adhesion and proliferation of osteoblast cells on the Mg-Zr-Sr-Ho alloys. The in vitro biodegradation and the biocompatibility of the Mg-Zr-Sr-Ho alloys were both influenced by the Ho concentration in the Mg alloys; Mg1Zr2Sr3Ho exhibited lower degradation rates than Mg1Zr2Sr and displayed the best biocompatibility compared with the other alloys. PMID:27553403

Determination of essential elements in beverages, herbal infusions and dietary supplements using a new straightforward sequential approach based on flame atomic absorption spectrometry.

PubMed

Gómez-Nieto, Beatriz; Gismera, Mª Jesús; Sevilla, Mª Teresa; Procopio, Jesús R

2017-03-15

A simple method based on FAAS was developed for the sequential multi-element determination of Cu, Zn, Mn, Mg and Si in beverages and food supplements with successful results. The main absorption lines for Cu, Zn and Si and secondary lines for Mn and Mg were selected to carry out the measurements. The sample introduction was performed using a flow injection system. Using the choice of the absorption line wings, the upper limit of the linear range increased up to 110mgL -1 for Mg, 200mgL -1 for Si and 13mgL -1 for Zn. The determination of the five elements was carried out, in triplicate, without the need of additional sample dilutions and/or re-measurements, using less than 3.5mL of sample to perform the complete analysis. The LODs were 0.008mgL -1 for Cu, 0.017mgL -1 for Zn, 0.011mgL -1 for Mn, 0.16mgL -1 for Si and 0.11mgL -1 for Mg. Copyright © 2016 Elsevier Ltd. All rights reserved.

40 CFR 79.55 - Base fuel specifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... fuel's production or distribution and/or for the successful operation of the test vehicle/engine... the methanol, ethanol, methane, and propane base fuels in addition to any such additives included... chloride), wt%, max 0.0004 Copper, mg/L, max 0.07 Water, wt%, max 0.5 Sulfur, wt%, max 0.004 (f) Methane...

40 CFR 79.55 - Base fuel specifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... fuel's production or distribution and/or for the successful operation of the test vehicle/engine... the methanol, ethanol, methane, and propane base fuels in addition to any such additives included... chloride), wt%, max 0.0004 Copper, mg/L, max 0.07 Water, wt%, max 0.5 Sulfur, wt%, max 0.004 (f) Methane...

40 CFR 79.55 - Base fuel specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... fuel's production or distribution and/or for the successful operation of the test vehicle/engine... the methanol, ethanol, methane, and propane base fuels in addition to any such additives included... chloride), wt%, max 0.0004 Copper, mg/L, max 0.07 Water, wt%, max 0.5 Sulfur, wt%, max 0.004 (f) Methane...

40 CFR 79.55 - Base fuel specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... fuel's production or distribution and/or for the successful operation of the test vehicle/engine... the methanol, ethanol, methane, and propane base fuels in addition to any such additives included... chloride), wt%, max 0.0004 Copper, mg/L, max 0.07 Water, wt%, max 0.5 Sulfur, wt%, max 0.004 (f) Methane...

40 CFR 79.55 - Base fuel specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fuel's production or distribution and/or for the successful operation of the test vehicle/engine... the methanol, ethanol, methane, and propane base fuels in addition to any such additives included... chloride), wt%, max 0.0004 Copper, mg/L, max 0.07 Water, wt%, max 0.5 Sulfur, wt%, max 0.004 (f) Methane...

Bacterial inhibition potential of 3D rapid-prototyped magnesium-based porous composite scaffolds–an in vitro efficacy study

PubMed Central

Ma, Rui; Lai, Yu-xiao; Li, Long; Tan, Hong-lue; Wang, Jia-li; Li, Ye; Tang, Ting-ting; Qin, Ling

2015-01-01

Bone infections are common in trauma-induced open fractures with bone defects. Therefore, developing anti-infection scaffolds for repairing bone defects is desirable. This study develoepd novel Mg-based porous composite scaffolds with a basal matrix composed of poly(lactic-co-glycolicacid) (PLGA) and tricalcium phosphate (TCP). A unique low-temperature rapid prototyping technology was used to fabricate the scaffolds, including PLGA/TCP (PT), PLGA/TCP/5%Mg (PT5M), PLGA/TCP/10%Mg (PT10M), and PLGA/TCP/15%Mg (PT15M). The bacterial adhesion and biofilm formation of Staphylococcus aureus were evaluated. The results indicated that the Mg-based scaffolds significantly inhibited bacterial adhesion and biofilm formation compared to PT, and the PT10M and PT15M exhibited significantly stronger anti-biofilm ability than PT5M. In vitro degratation tests revealed that the degradation of the Mg-based scaffolds caused an increase of pH, Mg2+ concentration and osmolality, and the increased pH may be one of the major contributing factors to the antibacterial function of the Mg-based scaffolds. Additionally, the PT15M exhibited an inhibitory effect on cell adhesion and proliferation of MC3T3-E1 cells. In conclusion, the PLGA/TCP/Mg scaffolds could inhibit bacterial adhesion and biofilm formation, and the PT10M scaffold was considered to be an effective composition with considerable antibacterial ability and good cytocompatibility. PMID:26346217

Tem Observation of Precipitates in Ag-Added Al-Mg-Si Alloys

NASA Astrophysics Data System (ADS)

Nagai, Takeshi; Matsuda, Kenji; Nakamura, Junya; Kawabata, Tokimasa; Marioara, Calin; Andersen, Sigmund J.; Holmestad, Randi; Hirosawa, Shoichi; Horita, Zenji; Terada, Daisuke; Ikeno, Susumu

The influence of addition of the small amount of transition metals to Al-Mg-Si alloy had reported by many researchers. In the previous our work, β' phase in alloys Al — 1.0 mass% Mg2Si -0.5 mass% Ag (Ag-addition) and Al -1.0 mass% Mg2Si (base) were investigated by high resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED), in order to understand the effect of Ag. In addition, the distribution of Ag was investigated by energy filtered mapping and high annular angular dark field scanning transmission electron microscopy (HAADF-STEM). One Ag-containing atomic column was observed per β' unit cell, and the unit cell symmetry is slightly changed as compared with the Ag-free β'. In this work, the microstructure of G.P. zone and β'' phase was investigated by TEM observation, which were formed before β' phase. The deformed sample by high pressure torsion (HPT) technique before aging was also investigated to understand its effect for aging in this alloy.

Effect of Cr, Ti, V, and Zr Micro-additions on Microstructure and Mechanical Properties of the Al-Si-Cu-Mg Cast Alloy

NASA Astrophysics Data System (ADS)

Shaha, S. K.; Czerwinski, F.; Kasprzak, W.; Friedman, J.; Chen, D. L.

2016-05-01

Uniaxial static and cyclic tests were used to assess the role of Cr, Ti, V, and Zr additions on properties of the Al-7Si-1Cu-0.5Mg (wt pct) alloy in as-cast and T6 heat-treated conditions. The microstructure of the as-cast alloy consisted of α-Al, eutectic Si, and Cu-, Mg-, and Fe-rich phases Al2.1Cu, Al8.5Si2.4Cu, Al5.2CuMg4Si5.1, and Al14Si7.1FeMg3.3. In addition, the micro-sized Cr/Zr/Ti/V-rich phases Al10.7SiTi3.6, Al6.7Si1.2TiZr1.8, Al21.4Si3.4Ti4.7VZr1.8, Al18.5Si7.3Cr2.6V, Al7.9Si8.5Cr6.8V4.1Ti, Al6.3Si23.2FeCr9.2V1.6Ti1.3, Al92.2Si16.7Fe7.6Cr8.3V1.8, and Al8.2Si30.1Fe1.6Cr18.8V3.3Ti2.9Zr were present. During solution treatment, Cu-rich phases were completely dissolved, while the eutectic silicon, Fe-, and Cr/Zr/Ti/V-rich intermetallics experienced only partial dissolution. Micro-additions of Cr, Zr, Ti, and V positively affected the alloy strength. The modified alloy in the T6 temper during uniaxial tensile tests exhibited yield strength of 289 MPa and ultimate tensile strength of 342 MPa, being significantly higher than that for the Al-Si-Cu-Mg base. Besides, the cyclic yield stress of the modified alloy in the T6 state increased by 23 pct over that of the base alloy. The fatigue life of the modified alloy was substantially longer than that of the base alloy tested using the same parameters. The role of Cr, Ti, V, and Zr containing phases in controlling the alloy fracture during static and cyclic loading is discussed.

Absorption properties of carbon dioxide enhanced-oil-recovery additives. Final Technical report, 12 May 1987-31 August 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, J.T.; Holbrook, S.T.

1990-01-01

The selection of the optimum foaming agent (surfactant) for enhancing oil production by carbon dioxide flooding is based on foamability and adsorption. Measurement of adsorption on carbonate cores from New Mexico reservoirs showed large adsorption differences between three commercial, high-foaming surfactants. An ethoxylated alcohol structure was least adsorbed, 0.64 mg/cc pore volume; an ethoxylated alcohol sulfate was next, 0.74 mg/cc pore volume; the highest adsorbed was a glyceryl sulfonate, 2.30 mg/cc pore volume. Commercial application of the foaming additive involves injecting alternate slugs of surfactant solution and carbon dioxide. Surfactant concentration should be determined to allow for the adsorption above.

21 CFR 101.79 - Health claims: Folate and neural tube defects.

Code of Federal Regulations, 2010 CFR

2010-04-01

... milligrams (mg)(4,000 micrograms (mcg)) folic acid daily before conception and continuing into early... folic acid are drugs). In addition, based on its review of a Hungarian intervention trial that reported periconceptional use of a multivitamin and multimineral preparation containing 800 mcg (0.8 mg) of folic acid, and...

21 CFR 101.79 - Health claims: Folate and neural tube defects.

Code of Federal Regulations, 2011 CFR

2011-04-01

... milligrams (mg)(4,000 micrograms (mcg)) folic acid daily before conception and continuing into early... folic acid are drugs). In addition, based on its review of a Hungarian intervention trial that reported periconceptional use of a multivitamin and multimineral preparation containing 800 mcg (0.8 mg) of folic acid, and...

Stoichiometry and kinetics of the anaerobic ammonium oxidation (Anammox) with trace hydrazine addition.

PubMed

Yao, Zongbao; Lu, Peili; Zhang, Daijun; Wan, Xinyu; Li, Yulian; Peng, Shuchan

2015-12-01

Purpose of this study is to investigate the stoichiometry and kinetics of anaerobic ammonium oxidation (Anammox) with trace hydrazine addition. The stoichiometry was established based on the electron balance of Anammox process with trace N2H4 addition. The stoichiometric coefficients were determined by the proton consumption and the changes in substrates and products. It was found that trace N2H4 addition can increase the yield of Anammox bacteria (AnAOB) and reduce NO3(-) yield, which enhances the Anammox. Subsequently, kinetic model of Anammox with trace N2H4 addition was developed, and the parameters of the anaerobic degradation model of N2H4 were obtained for the first time. The maximum specific substrate utilization rate, half-saturation constant and inhibition constant of N2H4 were 25.09mgN/g VSS/d, 10.42mgN/L and 1393.88mgN/L, respectively. These kinetic parameters might provide important information for the engineering applications of Anammox with trace N2H4 addition. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pituitary, ovarian and additional contraceptive effects of an estradiol-based combined oral contraceptive: results of a randomized, open-label study.

PubMed

Endrikat, Jan; Parke, Susanne; Trummer, Dietmar; Serrani, Marco; Duijkers, Ingrid; Klipping, Christine

2013-02-01

The estrogen step-down/progestogen step-up 28-day estradiol valerate/dienogest (E(2)V/DNG) oral contraceptive effectively inhibits ovulation; however, limited data are available regarding its effects on estradiol (E2), progesterone, luteinizing hormone (LH) and follicle-stimulating hormone (FSH) or its additional extraovarian contraceptive effects. In this secondary analysis, 100 women received E(2)V 3 mg on days 1-2, E(2)V 2 mg/DNG 2 mg on days 3-7, E(2)V 2 mg/DNG 3 mg on days 8-24, E(2)V 1 mg on days 25-26 and placebo on days 27-28 for one treatment cycle. Measures included the presence/absence of cervical mucus; endometrial thickness; and serum E2, progesterone, and gonadotropin levels. E2, progesterone, LH and FSH levels did not exhibit the typical ovulatory increase and remained relatively stable during the cycle. E(2)V/DNG reduced mean maximal endometrial thickness and proportion of women with visible cervical mucus. All parameters returned to pretreatment levels during the posttreatment cycle. E(2)V/DNG provides extraovarian contraceptive effects (reducing endometrial thickness and cervical mucus production) in addition to inhibiting ovulation, assuring contraceptive efficacy. Copyright © 2013 Elsevier Inc. All rights reserved.

77 FR 66149 - Significant New Use Rules on Certain Chemical Substances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-02

... ecological structural activity relationship (EcoSAR) analysis of test data on analogous esters, EPA predicts... milligram/cubic meter (mg/m\\3\\) as an 8-hour time-weighted average. In addition, based on EcoSAR analysis of... the PMN substance via the inhalation route. In addition, based on EcoSAR analysis of test data on...

Spin dependent transport properties of Mn-Ga/MgO/Mn-Ga magnetic tunnel junctions with metal(Mg, Co, Cr) insertion layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang, S. H.; Tao, L. L.; Liu, D. P., E-mail: dpliu@iphy.ac.cn

We report a first principles theoretical investigation of spin polarized quantum transport in Mn{sub 2}Ga/MgO/Mn{sub 2}Ga and Mn{sub 3}Ga/MgO/Mn{sub 3}Ga magnetic tunneling junctions (MTJs) with the consideration of metal(Mg, Co, Cr) insertion layer effect. By changing the concentration of Mn, our calculation shows a considerable disparity in transport properties: A tunneling magnetoresistance (TMR) ratio of 852% was obtained for Mn{sub 2}Ga-based MTJs, however, only a 5% TMR ratio for Mn{sub 3}Ga-based MTJs. In addition, the influence of insertion layer has been considered in our calculation. We found the Co insertion layer can increase the TMR of Mn{sub 2}Ga-based MTJ tomore » 904%; however, the Cr insertion layer can decrease the TMR by 668%; A negative TMR ratio can be obtained with Mg insertion layer. Our work gives a comprehensive understanding of the influence of different insertion layer in Mn-Ga based MTJs. It is proved that, due to the transmission can be modulated by the interfacial electronic structure of insertion, the magnetoresistance ratio of Mn{sub 2}Ga/MgO/Mn{sub 2}Ga MTJ can be improved by inserting Co layer.« less

The Role of Mg(OH)2 in the So-Called "Base-Free" Oxidation of Glycerol with AuPd Catalysts.

PubMed

Fu, Jile; He, Qian; Miedziak, Peter J; Brett, Gemma L; Huang, Xiaoyang; Pattisson, Samuel; Douthwaite, Mark; Hutchings, Graham J

2018-02-16

Mg(OH) 2 - and Mg(OH) 2 -containing materials can provide excellent performance as supports for AuPd nanoparticles for the oxidation of glycerol in the absence of base, which is considered to be a result of additional basic sites on the surface of the support. However, its influence on the reaction solution is not generally discussed. In this paper, we examine the relationship between the basic Mg(OH) 2 support and AuPd nanoparticles in detail using four types of catalyst. For these reactions, the physical interaction between Mg(OH) 2 and AuPd was adjusted. It was found that the activity of the AuPd nanoparticles increased with the amount of Mg(OH) 2 added under base-free conditions, regardless of its interaction with the noble metals. In order to investigate how Mg(OH) 2 affected the glycerol oxidation, detailed information about the performance of AuPd/Mg(OH) 2 , physically mixed (AuPd/C+Mg(OH) 2 ) and (AuPd/C+NaHCO 3 ) was obtained and compared. Furthermore, NaOH and Mg(OH) 2 were added during the reaction using AuPd/C. All these results indicate that the distinctive and outstanding performance of Mg(OH) 2 supported catalysts in base-free condition is in fact directly related to its ability to affect the pH during the reaction and as such, assists with the initial activation of the primary alcohol, which is considered to be the rate determining step in the reaction. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biodegradability engineering of biodegradable Mg alloys: Tailoring the electrochemical properties and microstructure of constituent phases

PubMed Central

Cha, Pil-Ryung; Han, Hyung-Seop; Yang, Gui-Fu; Kim, Yu-Chan; Hong, Ki-Ha; Lee, Seung-Cheol; Jung, Jae-Young; Ahn, Jae-Pyeong; Kim, Young-Yul; Cho, Sung-Youn; Byun, Ji Young; Lee, Kang-Sik; Yang, Seok-Jo; Seok, Hyun-Kwang

2013-01-01

Crystalline Mg-based alloys with a distinct reduction in hydrogen evolution were prepared through both electrochemical and microstructural engineering of the constituent phases. The addition of Zn to Mg-Ca alloy modified the corrosion potentials of two constituent phases (Mg + Mg2Ca), which prevented the formation of a galvanic circuit and achieved a comparable corrosion rate to high purity Mg. Furthermore, effective grain refinement induced by the extrusion allowed the achievement of much lower corrosion rate than high purity Mg. Animal studies confirmed the large reduction in hydrogen evolution and revealed good tissue compatibility with increased bone deposition around the newly developed Mg alloy implants. Thus, high strength Mg-Ca-Zn alloys with medically acceptable corrosion rate were developed and showed great potential for use in a new generation of biodegradable implants. PMID:23917705

Paper-Based Electrochemical Detection of Chlorate

PubMed Central

Shriver-Lake, Lisa C.; Zabetakis, Dan; Dressick, Walter J.; Stenger, David A.; Trammell, Scott A.

2018-01-01

We describe the use of a paper-based probe impregnated with a vanadium-containing polyoxometalate anion, [PMo11VO40]5−, on screen-printed carbon electrodes for the electrochemical determination of chlorate. Cyclic voltammetry (CV) and chronocoulometry were used to characterize the ClO3− response in a pH = 2.5 solution of 100 mM sodium acetate. A linear CV current response was observed between 0.156 and 1.25 mg/mL with a detection limit of 0.083 mg/mL (S/N > 3). This performance was reproducible using [PMo11VO40]5−-impregnated filter paper stored under ambient conditions for as long as 8 months prior to use. At high concentration of chlorate, an additional catalytic cathodic peak was seen in the reverse scan of the CVs, which was digitally simulated using a simple model. For chronocoulometry, the charge measured after 5 min gave a linear response from 0.625 to 2.5 mg/mL with a detection limit of 0.31 mg/mL (S/N > 3). In addition, the slope of charge vs. time also gave a linear response. In this case the linear range was from 0.312 to 2.5 mg/mL with a detection limit of 0.15 mg/mL (S/N > 3). Simple assays were conducted using three types of soil, and recovery measurements reported. PMID:29364153

Case study II: application of the divalent cation bridging theory to improve biofloc properties and industrial activated sludge system performance-using alternatives to sodium-based chemicals.

PubMed

Higgins, Matthew J; Sobeck, David C; Owens, Steven J; Szabo, Lynn M

2004-01-01

The objective of this study was to investigate the application of the divalent cation bridging theory (DCBT) as a tool in the chemical selection process at an activated sludge plant to improve settling, dewatering, and effluent quality. According to the DCBT, to achieve improvements, the goal of chemical selection should be to reduce the ratio of monovalent-to-divalent (M/D) cations. A study was conducted to determine the effect of using magnesium hydroxide [Mg(OH)2] as an alternative to sodium hydroxide (NaOH) at a full-scale industrial wastewater treatment plant. Floc properties and treatment plant performance were measured for approximately one year during two periods of NaOH addition and Mg(OH)2 addition. A cost analysis of plant operation during NaOH and Mg(OH)2 use was also performed. During NaOH addition, the M/D ratio was 48, while, during Mg(OH)2 addition, this ratio was reduced to an average of approximately 0.1. During the Mg(OH)2 addition period, the sludge volume index, effluent total suspended solids, and effluent chemical oxygen demand were reduced by approximately 63, 31, and 50%, respectively, compared to the NaOH addition period. The alum and polymer dose used for clarification was reduced by approximately 50 and 60%, respectively, during Mg(OH)2 addition. The dewatering properties of the activated sludge improved dewatering as measured by decreased capillary suction time and specific resistance to filtration (SRF), along with an increase in cake solids from the SRF test. This corresponded to a reduction in the volume of solids thickened by centrifuges at the treatment plant, which reduced the disposal costs of solids. Considering the costs for chemicals and solids disposal, the annual cost of using Mg(OH)2 was approximately 30,000 dollars to 115,000 dollars less than using NaOH, depending on the pricing of NaOH. The results of this study confirm that the DCBT is a useful tool for assessing chemical-addition strategies and their potential effect on activated sludge performance.

Fabricaton of brick without burning process

NASA Astrophysics Data System (ADS)

Zultiniar; Fadli, A.; Yenti, S. R.; Drastinawati; Thariq, M. R. A.

2018-04-01

Brick is a material with many applications on building materials. The purpose of this research is to study the effect of fly ash addition and hardening time on mechanical properties of brick produced. Brick was formed by mixing cement, clay, water and fly ash with addition point was 0;0,3;0,6;0,9;1,2 kg weight. Brick was dried at room temperature for 7, 14 and 21 days. The result showed that compressive strength with addition 0,6 kg fly ash for 21 days was the the strongest where that’s value was 9,375 N/mm2. The highest porosity was get in on 21,34 % with 1,2 fly ash addition. The result of TCLP showed that for Pb, Cu, Cr content was still below the quality standards based on PP No.85 TH 1999 and still considered harmless. Leachate value for Pb of 3,10 mg/L, 1,213 mg/L for Cr and 4,374 mg/L for Cu.

Development of a Hydrogen Uptake-Release Mg-Based Alloy by Adding a Polymer CMC (Carboxymethylcellulose, Sodium Salt) via Reaction-Accompanying Milling

NASA Astrophysics Data System (ADS)

Kwak, Young Jun; Choi, Eunho; Song, Myoung Youp

2018-03-01

The addition of carboxymethylcellulose, sodium salt (CMC) might improve the hydrogen uptake and release properties of Mg since it has a relatively low melting point and the melting of CMC during milling in hydrogen (reaction-accompanying milling) may make the milled samples be in good states to absorb and release hydrogen rapidly and to have a large hydrogen-storage capacity. Samples with compositions of 95 w/o Mg + 5 w/o CMC (named Mg-5CMC) and 90 w/o Mg + 10 w/o CMC (named Mg-10CMC) were prepared by adding CMC via reaction-accompanying milling. Activation of Mg-10CMC was completed after about 3 hydrogen uptake-release cycles. Mg-10CMC had a higher initial hydrogen uptake rate and a larger amount of hydrogen absorbed in 60 min, U (60 min), than Mg-5CMC before and after activation. At the cycle number of three (CN = 3), Mg-10CMC had a very high initial hydrogen uptake rate (1.56 w/o H/min) and a large U (60 min) (5.57 w/o H) at 593 K in hydrogen of 12 bar, showing that the activated Mg-10CMC has an effective hydrogen-storage capacity of about 5.6 w/o at 593 K in hydrogen of 12 bar at CN = 3. At CN = 2, Mg-10CMC released 1.00 w/o H in 2.5 min, 4.67 w/o H in 10 min, and 4.76 w/o H in 60 min at 648 K in hydrogen of 1.0 bar. The milling in hydrogen of Mg with CMC is believed to generate imperfections and cracks and reduce the particle size. The addition of 10 w/o CMC was more effective on the initial hydrogen uptake rate and U (60 min) compared with the 10 w/o additions of NbF5, TaF5, Fe2O3, and MnO, and the 10 w/o simultaneous addition of Ni, Fe, and Ti. To the best of our knowledge, this study is the first in which a polymer CMC is added to Mg by reaction-accompanying milling to improve the hydrogen storage properties of Mg.

Effect of Mg Addition on the Refinement and Homogenized Distribution of Inclusions in Steel with Different Al Contents

NASA Astrophysics Data System (ADS)

Wang, Linzhu; Yang, Shufeng; Li, Jingshe; Zhang, Shuo; Ju, Jiantao

2017-04-01

To investigate the effect of Mg addition on the refinement and homogenized distribution of inclusions, deoxidized experiments with different amounts of aluminum and magnesium addition were carried out at 1873 K (1600 °C) under the condition of no fluid flow. The size distribution of three-dimensional inclusions obtained by applying the modified Schwartz-Saltykov transformation from the observed planar size distribution, and degree of homogeneity in inclusion dispersion quantified by measuring the inter-surface distance of inclusions, were studied as a function of the amount of Mg addition and holding time. The nucleation and growth of inclusions based on homogeneous nucleation theory and Ostwald ripening were discussed with the consideration of supersaturation degree and interfacial energy between molten steel and inclusions. The average attractive force acted on inclusions in experimental steels was estimated according to Paunov's theory. The results showed that in addition to increasing the Mg addition, increasing the oxygen activity at an early stage of deoxidation and lowering the dissolved oxygen content are conductive to the increase of nucleation rate as well as to the refinement of inclusions Moreover, it was found that the degree of homogeneity in inclusion dispersion decreases with an increase of the attractive force acted on inclusions, which is largely dependent on the inclusion composition and volume fraction of inclusions.

Hydrogen production from steam reforming of ethylene glycol over iron loaded on MgO

NASA Astrophysics Data System (ADS)

Chen, Mingqiang; Wang, Yishuang; Liang, Tian; Yang, Jie; Yang, Zhonglian

2017-01-01

In this study, a series of Fe-based catalysts loaded on MgO were prepared by a precipitation technique. And they were tested in hydrogen production from steam reforming of ethylene glycol (SRE), which was a representative model compound of fast bio-oil. The catalysts were characterized by XRD, SEM and H2-TPR analysis. The results showed that the crystalline phases of catalysts contained Fe2O3 (Hematite), Fe3O4 (Magnetite), Fe2MgO4 (iron magnesium oxide) and MgO, and morphology of MgO was changed from the rugby-ball like particles to spherical particles with the addition of Fe. In addition, the catalytic test results indicated that the 18%Fe/MgO catalyst exhibited the highest ethylene glycol conversion (˜99.8%) and H2 molar percent (˜77%) during at the following conditions: H2O/C molar ratio is 5˜7, the feeding rate is 14 mL/h and the reaction temperature at 600˜650°C. Furthermore, the 18%Fe/MgO catalyst can keep outstanding stability during SRE for 12 h.

Adsorption properties of carbon dioxide enchanced oil recovery additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, J.T.; Holbrook, S.T.

1990-01-01

The selection of the optimum foaming agent (surfactant) for enhancing oil production by carbon dioxide flooding is based on foamability and adsorption. Measurements of adsorption on carbonate cores from New Mexico reservoirs showed large adsorption differences between three commercial, high-foaming surfactants. An ethoxylated alcohol structure was at least adsorbed, 0.64 mg/cc pore volume; an ethoxylated alcohol sulfate was next, 0.74 mg/cc pore volume; the highest adsorbed was a glyceryl sulfonate, 2.30 mg/cc pore volume. Commercial application of the foaming additive involves injecting alternate slugs of surfactant solution and carbon dioxide. Surfactant concentration should be determined to allow for the adsorptionmore » above. 9 refs., 27 figs., 6 tabs.« less

Incipient plasticity and indentation response of MgO surfaces using molecular dynamics

NASA Astrophysics Data System (ADS)

Tran, Anh-Son; Hong, Zheng-Han; Chen, Ming-Yuan; Fang, Te-Hua

2018-05-01

The mechanical characteristics of magnesium oxide (MgO) based on nanoindentation are studied using molecular dynamics (MD) simulation. The effects of indenting speed and temperature on the structural deformation and loading-unloading curve are investigated. Results show that the strained surface of the MgO expands to produce a greater relaxation of atoms in the surroundings of the indent. The dislocation propagation and pile-up for MgO occur more significantly with the increasing temperature from 300 K to 973 K. In addition, with increasing temperature, the high strained atoms with a great perturbation appearing at the groove location.

The effects of processing techniques on magnesium-based composite

NASA Astrophysics Data System (ADS)

Rodzi, Siti Nur Hazwani Mohamad; Zuhailawati, Hussain

2016-12-01

The aim of this study is to investigate the effect of processing techniques on the densification, hardness and compressive strength of Mg alloy and Mg-based composite for biomaterial application. The control sample (pure Mg) and Mg-based composite (Mg-Zn/HAp) were fabricated through mechanical alloying process using high energy planetary mill, whilst another Mg-Zn/HAp composite was fabricated through double step processing (the matrix Mg-Zn alloy was fabricated by planetary mill, subsequently HAp was dispersed by roll mill). As-milled powder was then consolidated by cold press into 10 mm diameter pellet under 400 MPa compaction pressure before being sintered at 300 °C for 1 hour under the flow of argon. The densification of the sintered pellets were then determined by Archimedes principle. Mechanical properties of the sintered pellets were characterized by microhardness and compression test. The results show that the density of the pellets was significantly increased by addition of HAp, but the most optimum density was observed when the sample was fabricated through double step processing (1.8046 g/cm3). Slight increment in hardness and ultimate compressive strength were observed for Mg-Zn/HAp composite that was fabricated through double step processing (58.09 HV, 132.19 MPa), as compared to Mg-Zn/HAp produced through single step processing (47.18 HV, 122.49 MPa).

Case report: efficacy and tolerability of ketamine in opioid-refractory cancer pain.

PubMed

Amin, Priya; Roeland, Eric; Atayee, Rabia

2014-09-01

A 36-year-old female with metastatic breast cancer involving bones, liver, lung, and pleura/chest wall with worsening back pain received weight-based intravenous (IV) ketamine and was transitioned to oral ketamine for cancer-related neuropathic pain. She had responded poorly to outpatient pain regimen of oxycodone sustained and immediate release, hydromorphone, gabapentin, and duloxetine (approximate 480 mg total oral morphine equivalents [OME]), reporting an initial pain score of 10/10. She was started on hydromorphone parenteral patient-controlled analgesia (PCA) bolus dose in addition to her outpatient regimen. Despite escalating doses of opioids and the addition of a lidocaine 5% patch, the patient's pain remained uncontrolled 6 days after admission. On hospital day 7, utilizing a hospital weight-based ketamine protocol, the patient was started on subanesthetic doses of ketamine at 0.2 mg/kg/h (288 mg/24 h) and titrated over 2 days to 0.4 mg/kg/h (576 mg/24 h). Then, a 3-day rotation from intravenous to oral ketamine was initiated, and the patient was discharged on ketamine oral solution, 75 mg every 8 hours. When the patient's dose was increased to 0.4 mg/kg/h, adequate pain relief was charted by the nurse within 120 minutes, "patient pain free and resting comfortably." Her pain continued to be well managed, with an average pain score of 5/10 with the ketamine continuous infusion and sustained with conversion to oral ketamine without any report of side effects. This was a 37% reduction in pain scores. With the patient's stabilized dose of ketamine, opioid requirements decreased by 61.4% (1017.5 mg reduction in total OME). The use of weight-based dosing of IV continuous infusion and transition to oral ketamine was effective and tolerable in the management of opioid-refractory, neuropathic cancer pain. It is hoped that this case report promotes a discussion regarding ketamine dosing in refractory neuropathic cancer pain.

Determination of endogenous concentrations of nitrites and nitrates in different types of cheese in the United States: method development and validation using ion chromatography.

PubMed

Genualdi, Susan; Jeong, Nahyun; DeJager, Lowri

2018-04-01

Nitrites and nitrates can be present in dairy products from both endogenous and exogenous sources. In the European Union (EU), 150 mg kg - 1 of nitrates are allowed to be added to the cheese milk during the manufacturing process. The CODEX General Standard for Food Additives has a maximum permitted level of 50 mg kg - 1 residue in cheese, while in the United States (U.S.) nitrates are unapproved for use as food additives in cheese. In order to be able to investigate imported cheeses for nitrates intentionally added as preservatives and the endogenous concentrations of nitrates and nitrites present in cheeses in the U.S. marketplace, a method was developed and validated using ion chromatography with conductivity detection. A market sampling of cheese samples purchased in the Washington DC metro area was performed. In 64 samples of cheese, concentrations ranged from below the method detection limit (MDL) to 26 mg kg - 1 for nitrates and no concentrations of nitrites were found in any of the cheese samples above the MDL of 0.1 mg kg - 1 . A majority of the samples (93%) had concentrations below 10 mg kg - 1 , which indicate the presence of endogenous nitrates. The samples with concentrations above 10 mg kg - 1 were mainly processed cheese spread, which can contain additional ingredients often of plant-based origin. These ingredients are likely the cause of the elevated nitrate concentrations. The analysis of 12 additional cheese samples that are liable to the intentional addition of nitrates, 9 of which were imported, indicated that in this limited study, concentrations of nitrate in the U.S.-produced cheeses did not differ from those in imported samples.

Improving High-Temperature Tensile and Low-Cycle Fatigue Behavior of Al-Si-Cu-Mg Alloys Through Micro-additions of Ti, V, and Zr

NASA Astrophysics Data System (ADS)

Shaha, S. K.; Czerwinski, F.; Kasprzak, W.; Friedman, J.; Chen, D. L.

2015-07-01

High-temperature tensile and low-cycle fatigue tests were performed to assess the influence of micro-additions of Ti, V, and Zr on the improvement of the Al-7Si-1Cu-0.5Mg (wt pct) alloy in the as-cast condition. Addition of transition metals led to modification of microstructure where in addition to conventional phases present in the Al-7Si-1Cu-0.5Mg base, new thermally stable micro-sized Zr-Ti-V-rich phases Al21.4Si4.1Ti3.5VZr3.9, Al6.7Si1.2TiZr1.8, Al2.8Si3.8V1.6Zr, and Al5.1Si35.4Ti1.6Zr5.7Fe were formed. The tensile tests showed that with increasing test temperature from 298 K to 673 K (25 °C to 400 °C), the yield stress and tensile strength of the present studied alloy decreased from 161 to 84 MPa and from 261 to 102 MPa, respectively. Also, the studied alloy exhibited 18, 12, and 5 pct higher tensile strength than the alloy A356, 354 and existing Al-Si-Cu-Mg alloy modified with additions of Zr, Ti, and Ni, respectively. The fatigue life of the studied alloy was substantially longer than those of the reference alloys A356 and the same Al-7Si-1Cu-0.5Mg base with minor additions of V, Zr, and Ti in the T6 condition. Fractographic analysis after tensile tests revealed that at the lower temperature up to 473 K (200 °C), the cleavage-type brittle fracture for the precipitates and ductile fracture for the matrix were dominant while at higher temperature fully ductile-type fracture with debonding and pull-out of cracked particles was identified. It is believed that the intermetallic precipitates containing Zr, Ti, and V improve the alloy performance at increased temperatures.

Catalytically Enhanced Hydrogen Sorption in Mg-MgH2 by Coupling Vanadium-Based Catalyst and Carbon Nanotubes

PubMed Central

Kadri, Atikah; Jia, Yi; Chen, Zhigang; Yao, Xiangdong

2015-01-01

Mg (MgH2)-based composites, using carbon nanotubes (CNTs) and pre-synthesized vanadium-based complex (VCat) as the catalysts, were prepared by high-energy ball milling technique. The synergistic effect of coupling CNTs and VCat in MgH2 was observed for an ultra-fast absorption rate of 6.50 wt. % of hydrogen per minute and 6.50 wt. % of hydrogen release in 10 min at 200 °C and 300 °C, respectively. The temperature programmed desorption (TPD) results reveal that coupling VCat and CNTs reduces both peak and onset temperatures by more than 60 °C and 114 °C, respectively. In addition, the presence of both VCat and CNTs reduces the enthalpy and entropy of desorption of about 7 kJ/mol H2 and 11 J/mol H2·K, respectively, as compared to those of the commercial MgH2, which ascribe to the decrease of desorption temperature. From the study of the effect of CNTs milling time, it is shown that partially destroyed CNTs (shorter milling time) are better to enhance the hydrogen sorption performance.

Effects of surface treatments and bonding types on the interfacial behavior of fiber metal laminate based on magnesium alloy

NASA Astrophysics Data System (ADS)

Zhang, Xi; Ma, Quanyang; Dai, Yu; Hu, Faping; Liu, Gang; Xu, Zouyuan; Wei, Guobing; Xu, Tiancai; Zeng, Qingwen; Xie, Weidong

2018-01-01

Fiber metal laminates based on magnesium alloys (MgFML) with different surface treatments and different bonding types were tested and analyzed. By using dynamic contact angle measurement and scanning electron microscopy (SEM), it was found that phosphating treatment can significantly improve the surface energy and wettability of magnesium alloy, and the surface energy of phosphated magnesium alloy was approximately 50% higher than that of abraded-only magnesium alloy. The single cantilever beam (SCB) test showed that the interfacial fracture energies of directly bonded MgFMLs based on abraded-only magnesium and abraded + phosphated magnesium were 650 J/m2 and 1030 J/m2, respectively, whereas the interfacial fracture energies of indirectly bonded MgFMLs were 1650 J/m2 and 2260 J/m2, respectively. Phosphating treatment and modified polypropylene interleaf were observed to improve the tensile strength and interfacial fracture toughness of MgFML. In addition, the rougher surface was more conducive to enhance the bonding strength and interfacial fracture toughness of MgFML.

Effect of Aluminum Addition on the Evolution of Microstructure, Crystallographic Texture and Mechanical Properties of Single Phase Hexagonal Close Packed Mg-Li Alloys

NASA Astrophysics Data System (ADS)

Bhagat Singh, P.; Sabat, R. K.; Kumaran, S.; Suwas, S.

2018-02-01

In the present investigation, an effort has been made to understand the effect of aluminum addition to α Mg-Li alloys. The corresponding composition Mg-4Li- xAl ( x = 0, 2, 4 and 6 wt.%) alloys have been prepared by stir casting route under an argon environment. Extrusion was carried out at 300 °C with the extrusion ratio of 15:1. Significant grain refinement was observed after extrusion. X-ray diffraction-based investigation of the cast and extruded alloys showed the presence of intermetallic compounds such as Mg17Al12 and AlLi in the Al-rich alloys namely, Mg-4Li- xAl ( x = 4 and 6 wt.%). These precipitates were also present in the extruded plus annealed samples, indicating the stability of the precipitates at high temperature. The bulk x-ray texture measurement revealed a crystallographic texture where the c-axis of the h.c.p crystals was perpendicular to the extrusion direction (ED) for extruded sample. A texture transition was observed on annealing. The c-axis was oriented parallel to the ED. Mechanical properties of the cast, extruded and extruded plus annealed material illustrate that the addition of Al led to enhancement in hardness, yield strength and ultimate tensile strength.

Thermal properties of spinel based solid solutions

NASA Astrophysics Data System (ADS)

O'Hara, Kelley Rae

Solid solution formation in spinel based systems proved to be a viable approach to decreasing thermal conductivity. Samples with systematically varied additions of MgGa2O4 to MgAl2O 4 were prepared and thermal diffusivity was measured using the laser flash technique. Additionally, heat capacity was measured using differential scanning calorimetry and modeled for the MgAl2O4-MgGa 2O4 system. At 200°C thermal conductivity decreased 24% with a 5 mol% addition of MgGa2O4 to the system. The solid solution continued to decrease the thermal conductivity by 13% up to 1000°C with 5 mol% addition. The decrease in thermal conductivity ultimately resulted in a decrease in heat flux when applied to a theoretical furnace lining, which could lead to energy savings in industrial settings. The MgAl2O4-Al2O3 phase equilibria was investigated to fully understand the system and the thermal properties at elevated temperatures. The solvus line between MgAl2O4 and Al2O3 has been defined at 79.6 wt% Al 2O3 at 1500°C, 83.0 wt% Al2O4 at 1600°C, and 86.5 wt% Al2O3 at 1700°C. A metastable region has been identified at temperatures up to 1700°C which could have significant implications for material processing and properties. The spinel solid solution region has been extended to form an infinite solid solution with Al2O3 at elevated temperatures. A minimum in melting at 1975°C and a chemistry of 96 wt% Al2O3 rather than a eutectic is present. Thermal properties in the MgAl2O4-Al2O 3 system were investigated in both the single phase solid solution region and the two phase region. The thermal diffusivity decreased through the MgAl 2O4 solid solution region and was at a minimum through the entire metastable (nucleation and growth) region. As Al2O 3 became present as a second phase the thermal diffusivity increased with Al2O3 content. There was an 11.7% increase in thermal diffusivity with a change in overall chemistry of 85.20 wt% Al2O 3 to 87.71 wt% Al2O3, due to the drastic change in final chemistry (38.3 wt% Al20 3) caused by the nucleation and growth region in the system.

The Safety, Effectiveness and Concentrations of Adjusted Lopinavir/Ritonavir in HIV-Infected Adults on Rifampicin-Based Antitubercular Therapy

PubMed Central

Decloedt, Eric H.; Maartens, Gary; Smith, Peter; Merry, Concepta; Bango, Funeka; McIlleron, Helen

2012-01-01

Objective Rifampicin co-administration dramatically reduces plasma lopinavir concentrations. Studies in healthy volunteers and HIV-infected patients showed that doubling the dose of lopinavir/ritonavir (LPV/r) or adding additional ritonavir offsets this interaction. However, high rates of hepatotoxicity were observed in healthy volunteers. We evaluated the safety, effectiveness and pre-dose concentrations of adjusted doses of LPV/r in HIV infected adults treated with rifampicin-based tuberculosis treatment. Methods Adult patients on a LPV/r-based antiretroviral regimen and rifampicin-based tuberculosis therapy were enrolled. Doubled doses of LPV/r or an additional 300 mg of ritonavir were used to overcome the inducing effect of rifampicin. Steady-state lopinavir pre-dose concentrations were evaluated every second month. Results 18 patients were enrolled with a total of 79 patient months of observation. 11/18 patients were followed up until tuberculosis treatment completion. During tuberculosis treatment, the median (IQR) pre-dose lopinavir concentration was 6.8 (1.1–9.2) mg/L and 36/47 (77%) were above the recommended trough concentration of 1 mg/L. Treatment was generally well tolerated with no grade 3 or 4 toxicity: 8 patients developed grade 1 or 2 transaminase elevation, 1 patient defaulted additional ritonavir due to nausea and 1 patient developed diarrhea requiring dose reduction. Viral loads after tuberculosis treatment were available for 11 patients and 10 were undetectable. Conclusion Once established on treatment, adjusted doses of LPV/r co-administered with rifampicin-based tuberculosis treatment were tolerated and LPV pre-dose concentrations were adequate. PMID:22412856

Magnesium based degradable biomaterials: A review

NASA Astrophysics Data System (ADS)

Gu, Xue-Nan; Li, Shuang-Shuang; Li, Xiao-Ming; Fan, Yu-Bo

2014-09-01

Magnesium has been suggested as a revolutionary biodegradable metal for biomedical applications. The corrosion of magnesium, however, is too rapid to match the rates of tissue healing and, additionally, exhibits the localized corrosion mechanism. Thus it is necessary to control the corrosion behaviors of magnesium for their practical use. This paper comprehensively reviews the research progress on the development of representative magnesium based alloys, including Mg-Ca, Mg-Sr, Mg-Zn and Mg-REE alloy systems as well as the bulk metallic glass. The influence of alloying element on their microstructures, mechanical properties and corrosion behaviors is summarized. The mechanical and corrosion properties of wrought magnesium alloys are also discussed in comparison with those of cast alloys. Furthermore, this review also covers research carried out in the field of the degradable coatings on magnesium alloys for biomedical applications. Calcium phosphate and biodegradable polymer coatings are discussed based on different preparation techniques used. We also compare the effect of different coatings on the corrosion behaviors of magnesium alloys substrate.

Effects of Be, Sr, Fe and Mg interactions on the microstructure and mechanical properties of aluminum based aeronautical alloys

NASA Astrophysics Data System (ADS)

Ibrahim, Mohamed Fawzy

The present work was carried out on a series of heat-treatable aluminum-based aeronautical alloys containing various amounts of magnesium (Mg), iron (Fe), strontium (Sr) and beryllium (Be). Tensile test bars (dendrite arm spacing ~ 24mum) were solutionized for either 5 or 12 hours at 540°C, followed by quenching in warm water (60°C). Subsequently, these quenched samples were aged at 160°C for times up to 12 hours. Microstructural assessment was performed. All heat-treated samples were pulled to fracture at room temperature using a servo-hydraulic tensile testing machine. The results show that Be causes partial modification of the eutectic silicon (Si) particles similar to that reported for Mg addition. Addition of 0.8 wt.% Mg reduced the eutectic temperature by ~10°C. During solidification of alloys containing high levels of Fe and Mg, without Sr, a peak corresponding to the formation of a Be-Fe phase (Al8Fe2BeSi) was detected at 611°C. The Be-Fe phase precipitates in a script-like morphology. A new quinary eutectic-like reaction was observed to take place near the end of solidification of high Mg, high Fe, Be-containing alloys. This new reaction is composed mainly of fine particles of Si, Mg2Si, pi-Al 8Mg3FeSi6 and (Be-Fe) phases. The volume fraction of this reaction decreased with the addition of Sr. The addition of Be has a noticeable effect on decreasing the beta-phase length, or volume fraction, this effect may be limited by adding Sr. Beryllium addition also results in the precipitation of the beta-phase in a nodular form, which reduces the harmful effects of these intermetallics on the alloy mechanical properties. Increasing both Mg and Fe levels led to an increase in the amount of the pi-phase; increasing the iron content led to an increase in the volume fraction of the partially soluble beta- and pi-phases, while Mg2Si particles were completely dissolved. The beta-phase platelets were observed to undergo changes in their morphology due to the dissolution, thinning, necking and fragmentation of these platelets upon increasing the solutionizing time. The pi-phase was observed to dissolve and/or transform into a cluster of very fine beta-phase platelets. In the as-cast conditions, increasing the Mg content leads to increased transformation of beta-phase platelets into Chinese-script pi-phase, regardless of the Fe content. This, in turn, decreases the harmful effect of the beta-phase. Increasing the solutionizing time leads to a decomposition of the pi-phase to the beta-phase, fragmentation of the beta-phase and spheroidization of both the eutectic Si and the pi-phase particles, thus improving alloy tensile properties. Two mechanisms of Mg2Si precipitate coarsening were observed to occur: (1) Ostwald ripening in the solution heat-treated samples and (2) clustering. Coarsening increases with increased solution heat treatment time, increased aging time, as well as with greater Mg contents. Increased Fe levels decrease the alloy quality index (Q) values, whereas adding Mg increases them. Introducing Be, in spite of it being a toxic material, Sr, or both, simultaneously improves the alloy quality index values, regardless of solutionizing time or Fe and Mg levels. Quality index values increase with solution heat treatment time from 5 to 12 hours. Higher Mg contents lead to an increase in alloy ductility, ultimate tensile strength (UTS) and yield strength (YS), while higher Fe levels can drastically decrease these properties. For the same levels of Fe and/or Mg, Be and Sr have significant effects in improving alloy mechanical properties; these effects can be readily observed in low levels of Fe and high Mg contents. Beryllium addition is beneficial in the case of high Fe contents as it lowers the harmful effects of Fe-phases in Al-Si alloys. In the case of high Fe contents, it seems that the addition of 500 ppm of Be is not sufficient for all interactions with other alloying elements. During the melting process the formation of Be-Sr phase (probably SrBe3O4 compound) decreases the free Be content and hence the alloy mechanical properties. The role of Be in preventing the oxidation of Mg and in changing the chemistry and morphology of the Fe-intermetallics is observed through improved mechanical properties of Be-containing alloys. The partial modification effect of both Mg and Be appears to improve the alloy tensile properties. Solutionizing and aging times are important parameters affecting the alloy tensile properties. The Mg2Si precipitates were confirmed to be the main hardening components of the 356 and 357 alloys investigated. The yield strength increases with greater Mg levels, reduced Fe levels, addition of Be, Sr-modification, solution heat treatment time and aging time. The present work was extended to include an investigation of the experimental 7073 aluminum alloy. (Abstract shortened by UMI.).

Protection of Pyruvate,Pi Dikinase from Maize against Cold Lability by Compatible Solutes 1

PubMed Central

Krall, John P.; Edwards, Gerald E.; Andreo, Carlos S.

1989-01-01

Most C4 species are chilling sensitive and certain enzymes like pyruvate,Pi dikinase of the C4 pathway are also cold labile. The ability of cations and compatible solutes to protect maize (Zea mays) dikinase against cold lability was examined. The enzyme in desalted extracts at pH 8 from preilluminated leaves could be protected against cold lability (at 0°C) by the divalent cations Mn2+, Mg2+, and Ca2+. There was substantial protection by sulfate based salts but little protection by chloride based salts of potassium or ammonium (concentration 250 millimolar). The degree of protection against cold lability under limiting MgCl2 (5 millimolar) was pH sensitive (maximum protection at pH 8), but independent of ionic strength (up to 250 millimolar by addition of KCl). In catalysis Mg2+ is required and Mn2+ could not substitute as a cofactor. Several compatible solutes reduced or prevented the cold inactivation of dikinase (in desalted extracts and the partially purified enzyme), including glycerol, proline, glycinebetaine and trimethylamine-N-oxide (TMAO). TMAO and Mg2+ had an additive effect in protecting dikinase against cold inactivation. TMAO could largely substitute for the divalent cation and addition of TMAO during cold treatment prevented further inactivation. Cold inactivation was partially reversed by incubation at room temperature; with addition of TMAO reversal was complete. The temperature dependence of inactivation at pH 8 and 3 millimolar MgCl2 was evaluated by incubation at 2 to 17°C for 45 minutes, followed by assay at room temperature. At preincubation temperatures below 11°C there was a progressive inactivation which could be prevented by TMAO (450 millimolar). The results are discussed relative to possible effects of the solutes on the quaternary structure of this enzyme, which is known to dissociate at low temperatures. PMID:16666527

Betaine can partially spare choline in chicks but only when added to diets containing a minimal level of choline.

PubMed

Dilger, Ryan N; Garrow, Timothy A; Baker, David H

2007-10-01

The ability of betaine to serve as a methyl donor in chicks was assessed in 3 bioassays using a choline-free purified diet that contained adequate methionine (Met). In assay 1, choline and betaine were each supplemented at 300 mg/kg in a 2 x 2 factorial arrangement of diets. Supplemental choline improved (P < 0.05) growth performance over the 9-d growth period, whereas betaine alone had no effect. In assay 2, graded supplements of choline produced a linear increase (P < 0.05) in growth performance criteria over a 9-d growth period. Additionally, hepatic betaine-homocysteine (Hcy) methyltransferase (BHMT) activity decreased linearly (P < 0.05), whereas plasma total Hcy remained unchanged. Addition of 260 or 600 mg/kg betaine to the choline-free basal diet did not affect growth performance or BHMT activity, but 600 mg/kg betaine reduced (P < 0.05) plasma total Hcy. Assay 3 was designed to quantify the ability of betaine to spare choline. Minimal supplemental choline requirements of 20.8 +/- 1.50 mg/d (722 mg/kg diet) and 10.5 +/- 1.03 mg/d (412 mg/kg diet) were estimated in the absence and presence of 1000 mg/kg supplemental betaine, respectively. Based on these estimates, 50% of the dietary choline requirement must be supplied as choline per se, but the remaining 50% can be replaced by betaine. Collectively, these data suggest betaine and Met have minimal choline-sparing activity in chicks fed purified diets devoid of preformed choline. However, addition of betaine to diets containing minimal choline allows a marked reduction in the total dietary choline requirement.

Online LC-GC-based analysis of minor lipids in various tree nuts and peanuts.

PubMed

Esche, Rebecca; Müller, Luisa; Engel, Karl-Heinz

2013-11-27

As information on free sterols/stanols and steryl/stanyl esters in nuts is lacking, the compositions and contents of these lipid constituents in ten different nut types were analyzed. The applied approach was based on online liquid chromatography-gas chromatography and enabled the simultaneous analysis of free sterols/stanols and individual steryl/stanyl fatty acid esters, and additionally of tocopherols and squalene. Total contents of free sterols/stanols ranged from 0.62 mg/g nut in hazelnuts to 1.61 mg/g nut in pistachios, with sitosterol as the predominant compound. Total contents of steryl/stanyl fatty acid esters were in the range of 0.11-1.26 mg/g nut, being lowest in Brazil nuts and highest in pistachios. There were considerable differences between the various nut types not only regarding the contents, but also the compositions of both classes. The levels of tocopherols were highest in pine nuts (0.33 mg/g nut); those of squalene were remarkably high in Brazil nuts (1.11 mg/g nut).

Capillary electrophoresis-based assay of phosphofructokinase-1.

PubMed

Malina, Andrew; Bryant, Sherrisse K; Chang, Simon H; Waldrop, Grover L; Gilman, S Douglass

2014-02-15

An assay was developed for phosphofructokinase-1 (PFK-1) using capillary electrophoresis (CE). In the glycolytic pathway, this enzyme catalyzes the rate-limiting step from fructose-6-phosphate and magnesium-bound adenosine triphosphate (Mg-ATP) to fructose-1,6-bisphosphate and magnesium-bound adenosine diphosphate (Mg-ADP). This enzyme has recently become a research target because of the importance of glycolysis in cancer and obesity. The CE assay for PFK-1 is based on the separation and detection by ultraviolet (UV) absorbance at 260 nm of Mg-ATP and Mg-ADP. The separation was enhanced by the addition of Mg²⁺ to the separation buffer. Inhibition studies of PFK-1 by aurintricarboxylic acid and palmitoyl coenzyme A were also performed. An IC₅₀ value was determined for aurintricarboxylic acid, and this value matched values in the literature obtained using coupled spectrophotometric assays. This assay for PFK-1 directly monitors the enzyme-catalyzed reaction, and the CE separation reduces the potential of spectral interference by inhibitors.

Capillary Electrophoresis-Based Assay of Phosphofructokinase-1

PubMed Central

Malina, Andrew; Bryant, Sherrisse K.; Chang, Simon H.; Waldrop, Grover L.; Gilman, S. Douglass

2013-01-01

An assay was developed for phosphofructokinase-1 (PFK-1) using capillary electrophoresis (CE). In the glycolytic pathway, this enzyme catalyzes the rate-limiting step from fructose-6-phosphate and magnesium-bound adenosine triphosphate (Mg-ATP) to fructose-1,6-bisphosphate and magnesium-bound adenosine diphosphate (Mg-ADP). This enzyme has recently become a research target because of the importance of glycolysis in cancer and obesity. The CE assay for PFK-1 is based on the separation and detection by UV absorbance at 260 nm of Mg-ATP and Mg-ADP. The separation was enhanced by addition of Mg2+ to the separation buffer. Inhibition studies of PFK-1 by aurintricarboxylic acid and palmitoyl coenzyme A were also performed. An IC50 value was determined for aurintricarboxylic acid, and this value matched values in the literature obtained using coupled spectrophotometric assays. This assay for PFK-1 directly monitors the enzyme-catalyzed reaction, and the CE separation reduces the potential of spectral interference by inhibitors. PMID:24444856

Solution stability of Captisol-stabilized melphalan (Evomela) versus Propylene glycol-based melphalan hydrochloride injection.

PubMed

Singh, Ramsharan; Chen, Jin; Miller, Teresa; Bergren, Michael; Mallik, Rangan

2016-12-14

The objective of this study was to compare the stability of recently approved Captisol-stabilized propylene glycol-free melphalan injection (Evomela™) against currently marketed propylene glycol-based melphalan injection. The products were compared as reconstituted solutions in vials as well as admixture solutions prepared from normal saline in infusion bags. Evomela and propylene glycol-based melphalan injection were reconstituted in normal saline and organic custom diluent, respectively, according to their package insert instructions. The reconstituted solutions were diluted in normal saline to obtain drug admixture solutions at specific drug concentrations. Stability of the solutions was studied at room temperature by assay of melphalan and determination of melphalan-related impurities. Results show that based on the increase in total impurities in propylene glycol-based melphalan injection at 0.45 mg/mL, Evomela admixture solutions are about 5, 9, 15 and 29 times more stable at concentrations of 0.45, 1.0, 2.0 and 5.0 mg/mL, respectively. Results confirmed that reconstituted Evomela solution can be stored in the vial for up to 1 h at RT or for up to 24 h at refrigerated temperature (2-8 °C) with no significant degradation. After storage in the vial, it remains stable for an additional 3-29 h after preparation of admixture solution in infusion bags at concentrations of 0.25-5.0 mg/mL, respectively. In addition, Evomela solution in saline, at concentration of 5.0 mg/mL melphalan was bacteriostatic through 72 h storage at 2-8 °C. Formulation of melphalan with Captisol technology significantly improved stability compared to melphalan hydrochloride reconstituted with propylene-glycol based diluents.

Mg I as a probe of the solar chromosphere - The atomic model

NASA Technical Reports Server (NTRS)

Mauas, Pablo J.; Avrett, Eugene H.; Loeser, Rudolf

1988-01-01

This paper presents a complete atomic model for Mg I line synthesis, where all the atomic parameters are based on recent experimental and theoretical data. It is shown how the computed profiles at 4571 A and 5173 A are influenced by the choice of these parameters and the number of levels included in the model atom. In addition, observed profiles of the 5173 A b2 line and theoretical profiles for comparison (based on a recent atmospheric model for the average quiet sun) are presented.

Structure-based Mechanism of CMP-2-keto-3-deoxymanno-octulonic Acid Synthetase

PubMed Central

Heyes, Derren J.; Levy, Colin; Lafite, Pierre; Roberts, Ian S.; Goldrick, Marie; Stachulski, Andrew V.; Rossington, Steven B.; Stanford, Deborah; Rigby, Stephen E. J.; Scrutton, Nigel S.; Leys, David

2009-01-01

The enzyme CMP-Kdo synthetase (KdsB) catalyzes the addition of 2-keto-3-deoxymanno-octulonic acid (Kdo) to CTP to form CMP-Kdo, a key reaction in the biosynthesis of lipopolysaccharide. The reaction catalyzed by KdsB and the related CMP-acylneuraminate synthase is unique among the sugar-activating enzymes in that the respective sugars are directly coupled to a cytosine monophosphate. Using inhibition studies, in combination with isothermal calorimetry, we show the substrate analogue 2β-deoxy-Kdo to be a potent competitive inhibitor. The ligand-free Escherichia coli KdsB and ternary complex KdsB-CTP-2β-deoxy-Kdo crystal structures reveal that Kdo binding leads to active site closure and repositioning of the CTP phosphates and associated Mg2+ ion (Mg-B). Both ligands occupy conformations compatible with an Sn2-type attack on the α-phosphate by the Kdo 2-hydroxyl group. Based on strong similarity with DNA/RNA polymerases, both in terms of overall chemistry catalyzed as well as active site configuration, we postulate a second Mg2+ ion (Mg-A) is bound by the catalytically competent KdsB-CTP-Kdo ternary complex. Modeling of this complex reveals the Mg-A coordinated to the conserved Asp100 and Asp235 in addition to the CTP α-phosphate and both the Kdo carboxylic and 2-hydroxyl groups. EPR measurements on the Mn2+-substituted ternary complex support this model. We propose the KdsB/CNS sugar-activating enzymes catalyze the formation of activated sugars, such as the abundant CMP-5-N-acetylneuraminic acid, by recruitment of two Mg2+ to the active site. Although each metal ion assists in correct positioning of the substrates and activation of the α-phosphate, Mg-A is responsible for activation of the sugar-hydroxyl group. PMID:19815542

Grain boundaries at the surface of consolidated MgO nanocrystals and acid-base functionality.

PubMed

Vingurt, Dima; Fuks, David; Landau, Miron V; Vidruk, Roxana; Herskowitz, Moti

2013-09-21

The increase of the surface basicity-acidity of MgO material by factors of 1.8-3.0 due to consolidation of its nanocrystals was demonstrated by the indicator titration. It was shown that the parallel increase of surface acidity and basicity is attributed to the formation of grain boundaries (GB) after MgO aerogel densification. A simple model predicting the increase of surface acidity-basicity of MgO that correlates with the results of direct measurements was proposed. The model is based on the study of the fine atomic structure at GB surface areas in consolidated MgO nanocrystals in the framework of Density Functional Theory. It is found that the displacements of coordinatively unsaturated surface ions near the GB are significant at the distances ~3-4 atomic layers from the geometrical contact plane between nanocrystals. The detailed analysis of atomic positions inside GB demonstrated the coordination deficiency of surface atoms at the GB areas leading to the formation of stretched bonds and to creation of low coordinated surface ions due to splitting of coordination numbers of surface atoms belonging to GB areas. Density of states for electrons shows the existence of additional states in the band gap close to the bottom of the conduction band. The adsorption energy of CO2 molecules atop oxygen atoms exposed at surface GB areas is of the same order of magnitude as that reported for oxygen atoms at crystallographic edges and corners of MgO crystals. It provides additional options for bonding of molecules at the surface of nanocrystalline MgO increasing the adsorption capacity and catalytic activity.

Re-use of winery wastewaters for biological nutrient removal.

PubMed

Rodríguez, L; Villaseñor, J; Buendía, I M; Fernández, F J

2007-01-01

The aim of this study was to evaluate the feasibility of the re-use of the winery wastewater to enhance the biological nutrient removal (BNR) process. In batch experiments it was observed that the addition of winery wastewater mainly enhanced the nitrogen removal process because of the high denitrification potential (DNP), of about 130 mg N/g COD, of the contained substrates. This value is very similar to that obtained by using pure organic substrates such as acetate. The addition of winery wastewater did not significantly affect either phosphorus or COD removal processes. Based on the experimental results obtained, the optimum dosage to remove each mg of N-NO3 was determined, being a value of 6.7 mg COD/mg N-NO3. Because of the good properties of the winery wastewater to enhance the nitrogen removal, the viability of its continuous addition in an activated sludge pilot-scale plant for BNR was studied. Dosing the winery wastewater to the pilot plant a significant increase in the nitrogen removal was detected, from 58 to 75%. The COD removal was slightly increased, from 89 to 95%, and the phosphorus removal remained constant.

Study on the mechanism of perpendicular magnetic anisotropy in Ta/CoFeB/MgO system

NASA Astrophysics Data System (ADS)

Lou, Yongle; Zhang, Yuming; Guo, Hui; Xu, Daqing; Yimen, Zhang

2017-06-01

The mechanism of perpendicular magnetic anisotropy (PMA) in a MgO-based magnetic tunnel junction (MTJ) has been studied in this article. By comparing the magnetic properties and elementary composition analysis for different CoFeB-based structures, such as Ta/CoFeB/MgO, Ta/CoFeB/Ta and Ru/CoFeB/MgO structures, it is found that a certain amount of Fe-oxide existing at the interface of CoFeB/MgO is helpful to enhance the PMA and the PMA is originated from the interface of CoFeB/MgO. In addition, Ta film plays an important role to enhance the PMA in Ta/CoFeB/MgO structure. Project supported by the National Defense Advance Research Foundation (No. 9140A08XXXXXX0DZ106), the Basic Research Program of Ministry of Education, China (No. JY10000925005), the Scientific Research Program Funded by Shaanxi Provincial Education Department (No.11JK0912), the Scientific Research Foundation of Xi’an University of Science and Technology (No. 2010011), the Doctoral Research Startup Fund of Xi’an University of Science and Technology (No. 2010QDJ029).

Two-dimensional electron gases in MgZnO/ZnO and ZnO/MgZnO/ZnO heterostructures grown by dual ion beam sputtering

NASA Astrophysics Data System (ADS)

Singh, Rohit; Arif Khan, Md; Sharma, Pankaj; Than Htay, Myo; Kranti, Abhinav; Mukherjee, Shaibal

2018-04-01

This work reports on the formation of high-density (~1013-1014 cm-2) two-dimensional electron gas (2DEG) in ZnO-based heterostructures, grown by a dual ion beam sputtering system. We probe 2DEG in bilayer MgZnO/ZnO and capped ZnO/MgZnO/ZnO heterostructures utilizing MgZnO barrier layers with varying thickness and Mg content. The effect of the ZnO cap layer thickness on the ZnO/MgZnO/ZnO heterostructure is also studied. Hall measurements demonstrate that the addition of a 5 nm ZnO cap layer results in an enhancement of the 2DEG density by about 1.5 times compared to 1.11 × 1014 cm-2 for the uncapped bilayer heterostructure with the same 30 nm barrier thickness and 30 at.% Mg composition in the barrier layer. From the low-temperature Hall measurement, the sheet carrier concentration and mobility are both found to be independent of the temperature. The capacitance-voltage measurement suggests a carrier density of ~1020 cm-3, confined in 2DEG at the MgZnO/ZnO heterointerface. The results presented are significant for the optimization of 2DEG for the eventual realization of cost-effective and large-area MgZnO/ZnO-based high-electron-mobility transistors.

Optimization of β-cyclodextrin-based flavonol extraction from apple pomace using response surface methodology.

PubMed

Parmar, Indu; Sharma, Sowmya; Rupasinghe, H P Vasantha

2015-04-01

The present study investigated five cyclodextrins (CDs) for the extraction of flavonols from apple pomace powder and optimized β-CD based extraction of total flavonols using response surface methodology. A 2(3) central composite design with β-CD concentration (0-5 g 100 mL(-1)), extraction temperature (20-72 °C), extraction time (6-48 h) and second-order quadratic model for the total flavonol yield (mg 100 g(-1) DM) was selected to generate the response surface curves. The optimal conditions obtained were: β-CD concentration, 2.8 g 100 mL(-1); extraction temperature, 45 °C and extraction time, 25.6 h that predicted the extraction of 166.6 mg total flavonols 100 g(-1) DM. The predicted amount was comparable to the experimental amount of 151.5 mg total flavonols 100 g(-1) DM obtained from optimal β-CD based parameters, thereby giving a low absolute error and adequacy of fitted model. In addition, the results from optimized extraction conditions showed values similar to those obtained through previously established solvent based sonication assisted flavonol extraction procedure. To the best of our knowledge, this is the first study to optimize aqueous β-CD based flavonol extraction which presents an environmentally safe method for value-addition to under-utilized bio resources.

Shape and structural motifs control of MgTi bimetallic nanoparticles using hydrogen and methane as trace impurities.

PubMed

Krishnan, Gopi; de Graaf, Sytze; Ten Brink, Gert H; Verheijen, Marcel A; Kooi, Bart J; Palasantzas, George

2018-01-18

In this work we report the influence of methane/hydrogen on the nucleation and formation of MgTi bimetallic nanoparticles (NPs) prepared by gas phase synthesis. We show that a diverse variety of structural motifs can be obtained from MgTi alloy, TiC x /Mg/MgO, TiC x /MgO and TiH x /MgO core/shell NPs via synthesis using CH 4 /H 2 as a trace gas, and with good control of the final NP morphology and size distribution. Moreover, depending on the concentration of Ti and type of employed trace gas, the as prepared MgTi NPs can be tuned from truncated hexagonal pyramid to triangular and hexagonal platelet shapes. The shape of MgTi NPs is identified using detailed analysis from selected area electron diffraction (SAED) patterns and tomography (3D reconstruction based on a tilt series of Bright-Field transmission electron microscopy (TEM) micrographs). We observe the truncated hexagonal pyramid as a shape of MgTi alloy NPs in contrast to Mg NPs that show a hexagonal prismatic shape. Moreover, based on our experimental observations and generic geometrical model analysis, we also prove that the formation of the various structural motifs is based on a sequential growth mechanism instead of phase separation. One of the prime reasons for such mechanism is based on the inadequacy of Mg to nucleate without template in the synthesis condition. In addition, the shape of the TiC x /TiH x core, and the concentration of Mg have strong influence on the shape evolution of TiC x /MgO and TiH x /MgO NPs compared to TiC x /Mg/MgO NPs, where the thermodynamics and growth rates of the Mg crystal planes dominate the final shape. Finally, it is demonstrated that the core shape of TiC x and TiH x is affected by the Mg/Ti target ratio (affecting the composition in the plasma), and the type of the trace gas employed. In the case of CH 4 the TiC x core forms a triangular platelet, while in the case of H 2 the TiH x core transforms into a hexagonal platelet. We elucidate the reason for the TiC x /TiH x core shape based on the presence of (i) defects, and (ii) hydrogen and carbon adsorption on {111} planes that alter the growth rates and surface facet stabilization.

Influence of Ni Interlayer on Microstructure and Mechanical Properties of Mg/Al Bimetallic Castings

NASA Astrophysics Data System (ADS)

Liu, Ning; Liu, Canchun; Liang, Chunyong; Zhang, Yongguang

2018-05-01

Dissimilar joining of magnesium and aluminum using a compound casting process was investigated in the present work. For the first time, a Ni interlayer prepared by plasma spraying was inserted between the two base metals to improve the interfacial characteristics. Examination of the interfacial regions using scanning electron microscopy, energy-dispersive X-ray spectroscopy, electron probe microanalysis, and X-ray diffraction revealed the formation of a three-layered interface between Mg and Al without the interlayer. The thickness of the interface was approximately 600 μm when the casting was performed at 700 °C and increased with increasing casting temperature. However, with the addition of the Ni interlayer, the Al-Mg reaction was successfully prevented, and metallurgical bonding between the Ni interlayer and two base metals was achieved at a casting temperature of 700 °C. Upon increasing this temperature, Mg-Ni and Al-Ni intermetallics were generated at the separate interfaces. The shear strength of the Mg/Al bimetallic castings with the Ni interlayer was substantially improved compared with that of the direct Mg/Al joint, with a maximum value of 25.4 MPa achieved at 700 °C. Fracture occurred mainly along the Mg/Ni interface for the Mg/Ni/Al multilayer structure castings.

Characterization of phenolics, glucosinolates and antioxidant activity of beverages based on apple juice with addition of frozen and freeze-dried curly kale leaves (Brassica oleracea L. var. acephala L.).

PubMed

Biegańska-Marecik, Róża; Radziejewska-Kubzdela, Elżbieta; Marecik, Roman

2017-09-01

The aim of this study was to determine the polyphenols, glucosinolates and ascorbic acid content as well as antioxidant activity of beverages on the base of apple juice with addition of frozen and freeze-dried curly kale leaves. Upon enrichment with frozen (13%) and freeze-dried curly kale (3%), the naturally cloudy apple juice was characterized by an increase in phenolic compounds by 2.7 and 3.3-times, accordingly. The antioxidant activity of beverages with the addition of curly kale ranged from 6.6 to 9.4μmol Trolox/mL. The obtained beverages were characterized glucosinolates content at 117.6-167.6mg/L and ascorbic acid content at 4,1-31,9mg/L. The results of sensory evaluation of colour, taste and consistency of apple juice and beverages with the addition of kale did not differ significantly prior to pasteurization (P≤0.05), whereas after the pasteurization the evaluated factors decreased significantly. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Y/Mg] stellar dating calibration

NASA Astrophysics Data System (ADS)

Titarenko, A.; Recio-Blanco, A.; de Laverny, P.; Hayden, M.; Guiglion, G.; Worley, C.

2018-04-01

Gaia DR1 has opened a new era of stellar age dating, that is crucial for many astrophysical objectives. In addition, the Gaia based isochrone fitting ages can be compared to other chemical clocks like the [Y/Mg] one (Nissen et al. 2015). In our work we have used ESO archived data of the AMBRE project (de Laverny et al. 2013) for UVES spectra, in order to evaluate the age [Y/Mg] abundance correlation for turn off stars. 310 turn off stars of the UVES-archive (setups 564 and 580) are included in the TGAS database. Isochrone fitting ages were derived. We have applied the GAUGUIN procedure for those stars to derive the Mg and the Y abundances. As the result we present the [Y/Mg] vs stellar age dependence for ~40 TO-stars.

Attenuation of Glass Dissolution in the Presence of Natural Additives

NASA Technical Reports Server (NTRS)

Sang, Jing C.; Barkatt, Aaron; OKeefe, John A.

1993-01-01

The study described here explored the dissolution kinetics of glasses in aqueous environments in systems which included a variety of natural crystalline solids in addition to the glass itself and the aqueous phase. The results demonstrated the possibility of a dramatic decrease in the rate of dissolution of silicate glass in the presence of certain varieties of olivine-based materials. This decrease in dissolution rate was shown to be due to the fact that these additives consist mostly of Mg-based material but also contain minor amounts of Al and Ca. The combined presence of Mg with these minor species affected the corrosion rate of the glass as a whole, including its most soluble components such as boron. The study has potentially important implications to the durability of glasses exposed to natural environments. The results may be relevant to the use of active backfill materials in burial sites for nuclear waste glasses as well as to better understanding of the environmental degradation of natural and ancient glasses.

Application of biosurfactants, rhamnolipid, and surfactin, for enhanced biodegradation of diesel-contaminated water and soil.

PubMed

Whang, Liang-Ming; Liu, Pao-Wen G; Ma, Chih-Chung; Cheng, Sheng-Shung

2008-02-28

This study investigated potential application of two biosurfactants, surfactin (SF) and rhamnolipid (RL), for enhanced biodegradation of diesel-contaminated water and soil with a series of bench-scale experiments. The rhamnolipid used in this study, a commonly isolated glycolipid biosurfactant, was produced by Pseudomonas aeruginosa J4, while the surfactin, a lipoprotein type biosurfactant, was produced by Bacillus subtilis ATCC 21332. Both biosurfactants were able to reduce surface tension to less than 30 dynes/cm from 72 dynes/cm with critical micelle concentration (CMC) values of 45 and 50 mg/L for surfactin and rhamnolipid, respectively. In addition, the results of diesel dissolution experiments also demonstrated their ability in increasing diesel solubility with increased biosurfactant addition. In diesel/water batch experiments, an addition of 40 mg/L of surfactin significantly enhanced biomass growth (2500 mg VSS/L) as well as increased diesel biodegradation percentage (94%), compared to batch experiments with no surfactin addition (1000 mg VSS/L and 40% biodegradation percentage). Addition of surfactin more than 40 mg/L, however, decreased both biomass growth and diesel biodegradation efficiency, with a worse diesel biodegradation percentage (0%) at 400 mg/L of SF addition. Similar trends were also observed for both specific rate constants of biomass growth and diesel degradation, as surfactin addition increased from 0 to 400 mg/L. Addition of rhamnolipid to diesel/water systems from 0 to 80 mg/L substantially increased biomass growth and diesel biodegradation percentage from 1000 to 2500 mg VSS/L and 40 to 100%, respectively. Rhamnolipid addition at a concentration of 160 mg/L provided similar results to those of an 80 mg/L addition. Finally, potential application of surfactin and rhamnolipid in stimulating indigenous microorganisms for enhanced bioremediation of diesel-contaminated soil was also examined. The results confirmed their enhancing capability on both efficiency and rate of diesel biodegradation in diesel/soil systems.

Surface and cut-edge corrosion behavior of Zn-Mg-Al alloy-coated steel sheets as a function of the alloy coating microstructure

NASA Astrophysics Data System (ADS)

Oh, Min-Suk; Kim, Sang-Heon; Kim, Jong-Sang; Lee, Jae-Won; Shon, Je-Ha; Jin, Young-Sool

2016-01-01

The effects of Mg and Al content on the microstructure and corrosion resistance of hot-dip Zn-Mg-Al alloycoated steel sheets were investigated. Pure Zn and Zn-based alloy coatings containing Mg (0-5 wt%) and Al (0.2-55 wt%) were produced by a hot-dip galvanizing method. Mg and Al addition induced formation of intermetallic microstructures, like primary Zn, Zn/MgZn2 binary eutectic, dendric Zn/Al eutectoid, and Zn/Al/MgZn2/ternary eutectic structures in the coating layer. MgZn2-related structures (Zn/MgZn2, Zn/Al/MgZn2, MgZn2) played an important role in increasing the corrosion resistance of Zn-Mg-Al alloy-coated steel sheets. Zn-3%Mg-2.5%Al coating layer containing a large volume of lamellar-shaped Zn/MgZn2 binary eutectic structures showed the best cut-edge corrosion resistance. The analysis indicated that Mg dissolved from MgZn2 in the early stage of corrosion and migrated to the cathodic region of steel-exposed cut-edge area to form dense and ordered protective corrosion products, leading to prolonged cathodic protection of Zn-Mg-Al alloy-coated steel sheets.

Combination antiplatelet therapy with aspirin and clopidogrel: the role of antecedent and concomitant doses of aspirin. An analysis of 711 patients.

PubMed

Serebruany, Victor L; Malinin, Alex I; Atar, Dan

2007-01-01

Numerous randomized studies have shown that the combination of clopidogrel with aspirin yields better clinical outcomes than monotherapy in patients with acute vascular events. However, the impact of the aspirin dose on the antiplatelet potency of clopidogrel is unclear. We sought to compare the antiplatelet profile of aspirin 81 mg (n = 252) versus aspirin 325 mg (n = 459) before and during conventional clopidogrel loading (300 mg), and/or clopidogrel maintenance (75 mg/daily) therapy. Secondary post hoc analysis of an existing dataset consisting of 711 patients after coronary stenting (n = 601) and ischemic stroke (n = 110) treated previously with aspirin for at least 1 month, and then with aspirin + clopidogrel for at least 7 days was performed. Platelet assessments include conventional and whole blood aggregometry, rapid cartridge-based analyzers, and expression of platelet/endothelial cell adhesion molecule-1, P-selectin, and GPIIb/IIIa activity by flow cytometry measured before and after addition of clopidogrel. There was a small but consistent yet non-significant trend towards more potent platelet inhibition with aspirin 325 mg compared to aspirin 81 mg for every platelet activation parameter before addition of clopidogrel. However, after loading and/or 1 week of chronic treatment with clopidogrel + aspirin, measured platelet parameters became very similar between the groups, and identical for collagen-induced aggregation and PFA-100 analyzer readings. Before addition of clopidogrel, aspirin 325 mg has a tendency to provide stronger platelet inhibition than aspirin 81 mg. However, when clopidogrel and aspirin are used in combination, the higher aspirin dose does not translate into superior antiplatelet action. Given that the existing body of evidence supports the comparable efficacy and, particularly, superior safety of lower versus higher doses of aspirin, aspirin 81 mg should be the dose used in combination with clopidogrel. 2007 S. Karger AG, Basel

Induced High-Yield Production of Zeaxanthin, Lutein, and β-Carotene by a Mutant of Chlorella zofingiensis.

PubMed

Huang, Weiping; Lin, Yan; He, Mingxia; Gong, Yuhao; Huang, Junchao

2018-01-31

Natural resources of zeaxanthin are extremely limited. A Chlorella zofingiensis mutant (CZ-bkt1), which could accumulate high amounts of zeaxanthin, was generated and characterized. CZ-bkt1 was achieved by treating the algal cells with a chemical mutagen followed by a color-based colony-screening approach. CZ-bkt1 was found to consist of a dysfunctional carotenoid ketolase, leading to the accumulation of zeaxanthin rather than to its downstream ketocarotenoid astaxanthin. Light irradiation, glucose, NaCl, and nitrogen deficiency all induced CZ-bkt1 to accumulate zeaxanthin. CZ-bkt1 accumulated zeaxanthin up to 7.00 ± 0.82 mg/g when induced by high-light irradiation and nitrogen deficiency and up to 36.79 ± 2.23 mg/L by additional feeding with glucose. Furthermore, in addition to zeaxanthin, CZ-bkt1 also accumulated high amounts of β-carotene (7.18 ± 0.72 mg/g or 34.64 ± 1.39 mg/L) and lutein (13.81 ± 1.23 mg/g or 33.97 ± 2.61 mg/L). CZ-bkt1 is the sole species up to date with the ability to accumulate high amounts of the three carotenoids that are essential for human health.

Control of Eu Luminescence Centers by Codoping of Mg and Si into Eu-Doped GaN

NASA Astrophysics Data System (ADS)

Lee, Dong-gun; Wakamatsu, Ryuta; Koizumi, Atsushi; Terai, Yoshikazu; Fujiwara, Yasufumi

2013-08-01

The effects of Mg and Si codoping on Eu luminescence properties have been investigated in Eu-doped GaN (GaN:Eu). The Mg codoping into GaN:Eu produced novel luminescence centers consisting of Eu and Mg, and increased photoluminescence (PL) intensity in Eu,Mg-codoped GaN (GaN:Eu,Mg). However, this increased PL intensity was quenched by thermal annealing in N2 ambient, which is due to activation of Mg acceptors. In GaN:Eu,Mg codoped additionally with Si (GaN:Eu,Mg,Si), on the other hand, the Eu-Mg centers disappeared, while an additional luminescence center appeared. Furthermore, the additional luminescence center showed no quenching under N2 annealing because Si donors compensated for the Mg acceptors in GaN. Thermal quenching of the luminescence center was also approximately half of that in GaN:Eu. These results indicate that the codoping with additional impurities in GaN:Eu is a powerful technique to control Eu luminescence centers for realization of improved device performance in red light-emitting diodes using GaN:Eu.

Composites Strengthened with Graphene Platelets and Formed in Semisolid State Based on α and α/β MgLiAl Alloys

NASA Astrophysics Data System (ADS)

Dutkiewicz, Jan; Rogal, Łukasz; Fima, Przemyslaw; Ozga, Piotr

2018-04-01

MgLiAl base composites strengthened with graphene platelets were prepared by semisolid processing of ball-milled alloy chips with 2% of graphene platelets. Composites strengthened with graphene platelets show higher hardness and yield stress than the cast alloys, i.e., 160 MPa as compared to 90 MPa for as-cast alloy MgLi9Al1.5. Mechanical properties for MgLiAl-based composites were similar or higher than for composites based on conventional AZ91 or WE43 alloys. The strengthening however was not only due to the presence of graphene, but also phases resulting from the reaction between carbon and lithium, i.e., Li2C2 carbide. Graphene platelets were located at globules boundaries resulting from semisolid processing for all investigated composites. Graphene platelets were in agglomerates forming continuous layers at grain boundaries in the composite based on the alloy MgLi4.5Al1.5. The shape of agglomerates was more complex and wavy in the composite based on MgLi9Al1.5 alloy most probably due to lithium-graphene reaction. Electron diffraction from the two-phase region α + β in MgLi9Al1.5 indicated that [001]α and [110]β directions are rotated about 4° from the ideal relationship [001] hex || [110] bcc phases. It showed higher lattice rotation than in earlier studies what is most probably caused by lattice slip and rotation during semisolid pressing causing substantial deformation particularly within the β phase. Raman spectroscopy studies confirmed the presence of graphene platelets within agglomerates and in addition the presence mainly of Li2C2 carbides in composites based on MgLi4.5Al1.5 and Mg9Li1.5Al alloys. From the character of Raman spectra refinement of graphene platelets was found in comparison with their initial size. The graphene areas without carbides contain graphene nanoplatelets with lateral dimension close to initial graphene sample. Electron diffraction allowed to confirm the presence of Li2C2 carbide at the surface of agglomerates found from Raman spectroscopy results.

Composites Strengthened with Graphene Platelets and Formed in Semisolid State Based on α and α/β MgLiAl Alloys

NASA Astrophysics Data System (ADS)

Dutkiewicz, Jan; Rogal, Łukasz; Fima, Przemyslaw; Ozga, Piotr

2018-05-01

MgLiAl base composites strengthened with graphene platelets were prepared by semisolid processing of ball-milled alloy chips with 2% of graphene platelets. Composites strengthened with graphene platelets show higher hardness and yield stress than the cast alloys, i.e., 160 MPa as compared to 90 MPa for as-cast alloy MgLi9Al1.5. Mechanical properties for MgLiAl-based composites were similar or higher than for composites based on conventional AZ91 or WE43 alloys. The strengthening however was not only due to the presence of graphene, but also phases resulting from the reaction between carbon and lithium, i.e., Li2C2 carbide. Graphene platelets were located at globules boundaries resulting from semisolid processing for all investigated composites. Graphene platelets were in agglomerates forming continuous layers at grain boundaries in the composite based on the alloy MgLi4.5Al1.5. The shape of agglomerates was more complex and wavy in the composite based on MgLi9Al1.5 alloy most probably due to lithium-graphene reaction. Electron diffraction from the two-phase region α + β in MgLi9Al1.5 indicated that [001]α and [110]β directions are rotated about 4° from the ideal relationship [001] hex || [110] bcc phases. It showed higher lattice rotation than in earlier studies what is most probably caused by lattice slip and rotation during semisolid pressing causing substantial deformation particularly within the β phase. Raman spectroscopy studies confirmed the presence of graphene platelets within agglomerates and in addition the presence mainly of Li2C2 carbides in composites based on MgLi4.5Al1.5 and Mg9Li1.5Al alloys. From the character of Raman spectra refinement of graphene platelets was found in comparison with their initial size. The graphene areas without carbides contain graphene nanoplatelets with lateral dimension close to initial graphene sample. Electron diffraction allowed to confirm the presence of Li2C2 carbide at the surface of agglomerates found from Raman spectroscopy results.

Mechanical properties of particulate composites based on a body-centered-cubic Mg-Li alloy containing boron

NASA Technical Reports Server (NTRS)

Whalen, R. T.; Gonzalez-Doncel, G.; Robinson, S. L.; Sherby, O. D.

1989-01-01

The effect of substituting the Mg metal in Mg-B composites by a Mg-14 wt pct Li solid solution on the ductility of the resulting composite was investigated using elastic modulus measurements on the P/M composite material prepared with a dispersion of B particles (in a vol pct range of 0-30) in a matrix of Mg-14 wt pct Li-1.5 wt pct Al. It was found that the elastic modulus of the composites increased rapidly with increasing boron, with specific stiffness values reaching about two times that of most structural materials. The values of the compression and tensile strengths increased significantly with boron additions. Good tensile ductility was achieved at the level of 10 vol pct B. However, at 20 vol pct B, the Mg-Li composite exhibited only limited tensile ductility (about 2 percent total elongation).

Evaluation of different approaches for improving the cycle life of MgNi-based electrodes for Ni-MH batteries

NASA Astrophysics Data System (ADS)

Rongeat, C.; Grosjean, M.-H.; Ruggeri, S.; Dehmas, M.; Bourlot, S.; Marcotte, S.; Roué, L.

Several methods have been investigated to enhance the cycle life of amorphous MgNi used as the negative electrode for Ni-MH batteries. The first approach involves modifying its surface composition in different ways, including the electroless deposition of a chromate conversion coating, the addition of chromate salt or NaF into the electrolyte and the mechanical coating of the particles with various compounds (e.g. TiO 2). Another approach consists of developing (MgNi + AB 5) composite materials. However, the cycle life of these modified MgNi electrodes remains unsatisfactory. On the other hand, the modification of the bulk composition of the MgNi alloy with elements such as Ti and Al appears to be more effective. For instance, a Mg 0.9Ti 0.1NiAl 0.05 electrode retains 67% of its initial discharge capacity (404 mAh g -1) after 15 cycles compared to 29% for MgNi. The charging conditions also have a great influence on the electrode cycle life as demonstrated by the existence of a charge input threshold below which minor capacity decay occurs. In addition, the particle size has a major influence on the electrode performance. We have developed an optimized electrode constituted of Mg 0.9Ti 0.1NiAl 0.05 particles with the appropriate size (>150 μm) showing a capacity decay rate as low as ∼0.2% per cycle when charged at 300 mAh g -1.

The role of the substrate surface morphology and water in growth of vertically aligned single-walled carbon nanotubes.

PubMed

Pint, Cary; Pheasant, Sean; Nicholas, Nolan; Horton, Charles; Hauge, Robert

2008-11-01

Growth of high quality, vertically aligned single-walled carbon nanotubes (carpets) is achieved using a rapid insertion hot filament chemical vapor deposition (HF-CVD) technique. The effect of the substrate morphology on growth is explored by comparing carpets grown on epitaxially polished MgO substrates to those grown on "as-cut", macroscopically rough MgO substrates. Depending on the substrate morphology, we observe differences in both the overall carpet morphology as well as the diameter distribution of nanotubes grown in the carpet based on optical measurements. In addition, we explore the role of water in the growth of carpets on MgO and the conventional Al2O3 coated Si substrates. We find that the addition of a small amount of water is beneficial to the growth rates of the SWNT carpets, enhancing the growth rates by up to eight times.

TheoSSA - Model WD Spectra on Demand: The Impact of Ne, Na, Mg, and Iron-group Elements on the Balmer Lines

NASA Astrophysics Data System (ADS)

Reindl, N.; Rauch, T.

2015-06-01

The registered German Astrophysical Virtual Observatory (GAVO) service TheoSSA provides easy access to synthetic stellar spectra. This GAVO database contains already ten thousands of these, which were calculated with different chemical compositions of the elements H to Ni. In addition to the database, it is possible to calculate individual spectra for hot, compact stars based on the Tübingen NLTE Model-Atmosphere Package (TMAP) via the TMAW service. The TMAW models were, in the pilot phase, restricted to the elements H, He, C, N, and O. Now, TMAW is extended to additionally consider opacities from Ne, Na, and Mg. Soon, TMAW will also be able to include the opacities from the so-called iron-group elements (Ca - Ni). We describe the improvements and show the impact of Ne, Na, Mg, and iron-group elements on the Balmer lines.

Graphene based resonance structure to enhance the optical pressure between two planar surfaces.

PubMed

Hassanzadeh, Abdollah; Azami, Darya

2015-12-28

To enhance the optical pressure on a thin dielectric sample, a resonance structure using graphene layers coated over a metal film on a high index prism sputtered with MgF2 was theoretically analyzed. The number of graphene layers and the thicknesses of metal and MgF2 films were optimized to achieve the highest optical pressure on the sample. Effects of three different types of metals on the optical pressure were investigated numerically. In addition, simulations were carried out for samples with various thicknesses. Our numerical results show that the optical pressure increased by more than five orders of magnitude compared to the conventional metal-film-base resonance structure. The highest optical pressure was obtained for 10 layers of graphene deposited on 29-nm thick Au film and 650 nm thickness of MgF2 at 633nm wavelength, The proposed graphene based resonance structure can open new possibilities for optical tweezers, nanomechnical devices and surface plasmon based sensing and imaging techniques.

Competitive/co-operative interactions in acid base sandwich: role of cation vs. substituents.

PubMed

Kalpana, Ayyavoo; Akilandeswari, Lakshminarayanan

2017-11-15

The cation-π interaction can be envisaged as a lewis acid base interaction, and it is in line with Pearson's acid base concept. The critical examination of interactions between the π-acids (alkali metal cations - Li + , Na + and alkaline earth metal cations Mg 2+ , Ca 2+ ) on one face and tripodal Cr(CO) 3 moiety on the other π face of substituted arenes demonstrates the role of cation and substitutents in manipulating the interactions between them. The interaction of the two π acids on both faces of arene is not expectedly additive, rather it shows either depreciation of interaction energy revealing the competition of acids toward the base or enhancement of interaction energy denoting a cooperative effect. Among the metal cations under study, Mg 2+ shows a cooperative gesture. Although the substituents play a meek role, they unfailingly exert their electronic effects and are amply documented by excellent correlation of various parameters with the Hammett constant σ m . The elusive switching of λ max from the UV to IR region on binding Mg 2+ with substituted arene-Cr(CO) 3 complex is a characteristic clue that TDDFT can help design the ionic sensors for Mg 2+ cations.

Density functional theory (DFT) study on the hydrolysis behavior of degradable Mg/Mg alloys for biomedical applications

NASA Astrophysics Data System (ADS)

Nezafati, Marjan

Magnesium-based (Mg and/or Mg alloys) materials possess many advantageous physicochemical/biological characteristics such as good biocompatibility and similarity of the mechanical properties to the human bone tissue, which renders this material a promising candidate for the biomedical and implant applications. One of the most attractive features of Mg-based materials is the degradability in the physiological environment. With the burst of research on the biodegradable materials for the healthcare device applications, Mg and its alloys attracted a strong attention in the bioengineering field in recent years. However, the major limitation of applying Mg-based materials to biomedical applications is the fast degradation/corrosion rate with regards to the healing process time-span. In the present thesis, an atomistic model employing the density-functional theory (DFT) has been developed to study the hydrolysis process by understanding the influences of commonly used alloying elements (zinc (Zn), calcium (Ca), aluminum (Al), and yttrium (Y)) and the crystallographic orientation of the dissolution surfaces (basal (0001), prism (1010), and pyramidal (1011) planes) on the corrosion behavior. These parameters are known to strongly impact the initial hydrolysis phenomena of Mg-based materials. To develop the atomistic computational model, we have implemented the Dmol3 software package in conjunction with PBE (Perdew, Burke and Ernzerhof) correlation energy functional in the GGA (generalized gradient approximation) scheme. Throughout the thesis, we performed three sets of calculations, i) surface energy, ii) dissolution potential, and iii) water adsorption computations, to examine the hydrolysis mechanism and the subsequent corrosion/degradation of Mg/Mg alloys. The total energy changes of various Mg-based systems in different conditions for these surface energies, dissolution behavior, and tendency of the system for adsorbing the water molecule were quantified. The results obtained from the atomistic model showed that these structural/compositional parameters (i.e., different types of alloying elements and surface planes) can considerably impact the stability of surfaces that are in contact with the corrosion media. The dissolution potential change computation predicted that Al can prevent the dissolution of Mg atoms from the surface of Mg-Al systems. In addition, it was found that the trend of water adsorption phenomena with different alloying elements/planes can be well-explained by the stability of corrosion surface.

Re-examining the 26Mg(α ,α')26Mg reaction: Probing astrophysically important states in 26Mg

NASA Astrophysics Data System (ADS)

Adsley, P.; Brümmer, J. W.; Li, K. C. W.; Marín-Lámbarri, D. J.; Kheswa, N. Y.; Donaldson, L. M.; Neveling, R.; Papka, P.; Pellegri, L.; Pesudo, V.; Pool, L. C.; Smit, F. D.; van Zyl, J. J.

2017-11-01

Background: The 22Ne(α ,n )25Mg reaction is one of the neutron sources for the s process in massive stars. The properties of levels in 26Mg above the α -particle threshold control the strengths of the 22Ne(α ,n )25Mg and 22Ne(α ,γ )26Mg reactions. The strengths of these reactions as functions of temperature are one of the major uncertainties in the s process. Purpose: Information on the existence, spin, and parity of levels in 26Mg can assist in constraining the strengths of the 22Ne(α ,γ )26Mg and 22Ne(α ,n )25Mg reactions, and therefore in constraining s -process abundances. Methods: Inelastically scattered α particles from a 26Mg target were momentum-analyzed in the K600 magnetic spectrometer at iThemba LABS, South Africa. The differential cross sections of states were deduced from the focal-plane trajectory of the scattered α particles. Based on the differential cross sections, spin and parity assignments to states are made. Results: A newly assigned 0+ state was observed in addition to a number of other states, some of which can be associated with states observed in other experiments. Some of the deduced Jπ values of the states observed in the present study show discrepancies with those assigned in a similar experiment performed at RCNP Osaka. The reassignments and additions of the various states can strongly affect the reaction rate at low temperatures. Conclusion: The number, location, and assignment of levels in 26Mg that may contribute to the 22Ne+α reactions are not clear. Future experimental investigations of 26Mg must have an extremely good energy resolution to separate the contributions from different levels. Coincidence experiments of 26Mg provide a possible route for future investigations.

Effects of Mg nanopowders intergranular addition on the magnetic properties and corrosion resistance of sintered Nd-Fe-B

NASA Astrophysics Data System (ADS)

Li, Zhi-jie; Wang, Xiao-er; Li, Jia-yang; Li, Jia; Wang, Hong-zhi

2017-11-01

In order to improve the magnetic properties and corrosion resistance of sintered Nd-Fe-B magnets, the (PrNd)29.9Dy0.1B1Co1Cu0.15Febal (wt%) powders were mixed with Mg nanopowders, as grain boundary modifiers. For Nd-Fe-B magnets with 0.1-0.4 wt% Mg addition, the result showed that addition amount of 0.1 wt% Mg, Hcj reaches the maximum value of 999.1 kA/m, Br reaches 1.436T, (BH)max reaches 396.9 kJ/m3 and magnet density is 7.42 g/cm3, which are related to the microstructural modification of grain boundaries and the magnet density. Effects of Mg addition on corrosion behavior in sulphuric acid and sodium chloride solution were researched by electrochemical workstation. With increase of Mg addition level, the magnet turns to have a higher corrosion potential and lower corrosion current density, the corrosion poverty is improved. However, temperature coefficient remained nearly unchanged with Mg addition.

Different effects of a novel CaO-MgO-SiO₂-based multiphase glass-ceramic on cell behaviors of normal and cancer cells in vitro.

PubMed

Zhang, Mengjiao; Chen, Xianchun; Pu, Ximing; Liao, Xiaoming; Huang, Zhongbing; Yin, Guangfu

2014-04-01

The effects in vitro of a novel multiphase glass-ceramic (with nominal composition of 43.19% CaO, 7.68% MgO, and 49.13% SiO2 in weight percent) on cell adhesion, proliferation, differentiation and ultrastructure of human osteosarcoma cell line MG63, mouse fibroblasts L929, and human lung adenocarcinoma epithelial cell line A549 were investigated in this research. Scanning electron microscopy (SEM) micrographs revealed that the surface morphology of this glass-ceramic was beneficial to cell adhesion. The glass-ceramic extracts at certain concentrations could stimulate the proliferation and differentiation of MG63 and L929 cells, whereas inhibit A549 proliferation, which might be resulted from the released Si ions. In addition, when cultured with 0.1mg/mL glass-ceramic powder suspension, the cell ultrastructure of MG63 showed abundant organelles and L929 displayed the phenomena of cellular stress response. While more interestingly, A549 exhibited chromatin condensation, mitochondria swell and RER expansion, which was presumed to be early signs of apoptosis. These results suggest that this novel CaO-MgO-SiO2-based multiphase glass-ceramic has potential for bone regeneration and tissue engineering applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Thermodynamics and Kinetics of Three Mg-H-VN Complexes in Mg:GaN from Combined First-Principles Calculation and Experiment

NASA Astrophysics Data System (ADS)

Lee, Donghwa; Mitchell, Brandon; Fujiwara, Y.; Dierolf, V.

2014-05-01

An understanding of the formation and dissociation process of Mg-H defects in GaN is of paramount importance for high efficient GaN-based solid-state lighting. Through a combination of first-principle calculations and experimental observations, we find the existence of three types of Mg related centers forming different Mg-H-VN complexes in Mg:GaN. Our study shows that the three different arrangements, which differ by the relative position of the H, determine the degree of acceptor passivation by changing their charge state from +3 to +1. The energetic study demonstrates that the relative stability of the defect complexes can vary with the location of the Fermi level, as well as thermal annealing and electron beam irradiation. The inclusion of a VN is shown to produce an additional variance in optical spectra associated with Mg acceptor activation, resulting from changes in the defect configurations and charge states. Our study shows that these three Mg-H-VN complexes are key components for understanding the Mg acceptor activation and passivation processes.

Intercalation of IR absorber into layered double hydroxides: Preparation, thermal stability and selective IR absorption

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Haifeng; Tang, Pinggui; Feng, Yongjun, E-mail: yjfeng@mail.buct.edu.cn

2012-03-15

Highlights: Black-Right-Pointing-Pointer PMIDA anions were intercalated into Mg{sub 2}Al-NO{sub 3} LDH by anion-exchange method. Black-Right-Pointing-Pointer The prepared material has highly selective IR absorption property in 9-11 {mu}m. Black-Right-Pointing-Pointer The obtained material has practical applications as heat-retaining additive. -- Abstract: N-phosphonomethyl aminodiacetic acid (PMIDA) was intercalated into the interlayer spacing of layered double hydroxides (LDH) by an anion-exchange method. The intercalated LDHs were characterized by various techniques such as powder X-ray diffraction (XRD), FT-IR spectroscopy, elemental analysis and simultaneous thermogravimetric and mass spectrometry (TG-MS) in details. The results show the formation of Mg{sub 2}Al-PMIDA LDH based on the expansion of d-spacingmore » from 0.89 nm to 1.22 nm and the disappearance of the characteristic IR absorption band at 1384 cm{sup -1} for NO{sub 3}{sup -} anions. The incorporation of Mg{sub 2}Al-PMIDA LDH into the low density polyethylene (LDPE) as an additive enhances the selectivity of IR absorption in the main wavelength region 9-11 {mu}m for radiant heat loss at night. Mg{sub 2}Al-PMIDA LDH as a heat-retaining additive has practical application in agricultural plastic films.« less

Physical properties and FTIR analysis of rice-oat flour and maize-oat flour based extruded food products containing olive pomace.

PubMed

Ying, DanYang; Hlaing, Mya Myintzu; Lerisson, Julie; Pitts, Keith; Cheng, Lijiang; Sanguansri, Luz; Augustin, Mary Ann

2017-10-01

Olive pomace, a waste stream from olive oil processing, was fractionated by centrifugation to obtain a supernatant and a flesh-enriched fraction, and freeze dried to obtain a powder. The dried supernatant contained 5.8% moisture, 4.8% protein, 3.5% fat, 3.5% ash, 82.4% carbohydrate (including 17.2% dietary fiber) and polyphenols (2970mg gallic acid equivalents (GAE)/100g). The dried flesh-enriched fraction, contained 5.9% moisture, 13.4% protein, 14.2% fat, 3.5% ash, 63.1% carbohydrate (including 42.7% dietary fiber) and polyphenols (1960mg GAE/100g). The extruded products using rice-oat flour or maize-oat flour mixtures as the base were formulated to contain 5% or 10% olive pomace fractions (dry basis). The extruded products with added olive pomace fractions has higher fiber (2-7g/100g) and polyphenol contents (67-161mg GAE/100g) compared to the corresponding mixtures of rice-oat flour base (0.92g/100g fiber, 20mg GAE/100g) or maize-oat flour base (3.2g/100g fiber, 20mg GAE/100g) without olive pomace fractions. Addition of olive pomace fractions reduced the die pressure and specific mechanical energy during extrusion and resulted in lower radial expansion in the extruded product. The impact of the addition of olive pomace fraction on physical characteristics of the extruded product is higher for rice-oat flour base than maize-oat flour base. The underlining mechanism was explained by FTIR analysis. FTIR showed that there were significant changes in the carbohydrate components and the structure of the proteins on extrusion, with consequent effects on the expansion and density of the extruded product. This study showed the feasibility of preparing fiber and polyphenol enriched extruded products by incorporation of olive pomace. This shows the potential of recovery and diversion of edible components from waste streams of olive oil processing for formulation of extruded products. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Facial injections of hyaluronic acid-based fillers for malformations. Preliminary study regarding scar tissue improvement and cosmetic betterment].

PubMed

Franchi, G; Neiva-Vaz, C; Picard, A; Vazquez, M-P

2018-06-01

Cross-linked hyaluronic acid-based fillers have gained rapid acceptance for treating facial wrinkles, deep tissue folds and sunken areas due to aging. This study evaluates, in addition to space-filling properties, their effects on softness and elasticity as a secondary effect, following injection of 3 commercially available cross-linked hyaluronic acid-based fillers (15mg/mL, 17,5mg/mL and 20mg/mL) in patients presenting with congenital or acquired facial malformations. We started injecting gels of cross-linked hyaluronic acid-based fillers in those cases in 2013; we performed 46 sessions of injections in 32 patients, aged from 13-32. Clinical assessment was performed by the patient himself and by a plastic surgeon, 15 days after injections and 6-18 months later. Cross-linked hyaluronic acid-based fillers offered very subtle cosmetic results and supplemented surgery with a very high level of satisfaction of the patients. When injected in fibrosis, the first session enhanced softness and elasticity; the second session enhanced the volume. Cross-linked hyaluronic acid-based fillers fill sunken areas and better softness and elasticity of scar tissues. In addition to their well-understood space-filling function, as a secondary effect, the authors demonstrate that cross-linked hyaluronic acid-based fillers improve softness and elasticity of scarring tissues. Many experimental studies support our observations, showing that cross-linked hyaluronic acid stimulates the production of several extra-cellular matrix components, including dermal collagen and elastin. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

The Interplay of Al and Mg Speciation in Advanced Mg Battery Electrolyte Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

See, Kimberly A.; Chapman, Karena W.; Zhu, Lingyang

2016-01-13

Mg batteries are an attractive alternative to Li-based energy storage due to the possibility of higher volumetric capacities with the added advantage of using sustainable materials. A promising emerging electrolyte for Mg batteries is the magnesium aluminum chloride complex (MACC) which shows high Mg electrodeposition and stripping efficiencies and relatively high anodic stabilities. As prepared, MACC is inactive with respect to Mg deposition; however, efficient Mg electrodeposition can be achieved following an electrolytic conditioning process. Through the use of Raman spectroscopy, surface enhanced Raman spectroscopy, 27Al and 35Cl nuclear magnetic resonance spectroscopy, and pair distribution function analysis, we explore themore » active vs inactive complexes in the MACC electrolyte and demonstrate the codependence of Al and Mg speciation. These techniques report on significant changes occurring in the bulk speciation of the conditioned electrolyte relative to the as-prepared solution. Analysis shows that the active Mg complex in conditioned MACC is very likely the [Mg2(μ–Cl)3·6THF]+ complex that is observed in the solid state structure. Additionally, conditioning creates free Cl– in the electrolyte solution, and we suggest the free Cl– adsorbs at the electrode surface to enhance Mg electrodeposition.« less

Effect of Bi(Mg1/2Ti1/2)O3 addition on the electrical properties of Si-Mn modified on SrTiO3

NASA Astrophysics Data System (ADS)

Roh, Yoon-ah; Masaki, Takaki; Yoon, Dae-Ho

2015-05-01

Single-Crystalline Strontium titanate (SrTiO3) has been widely used in many fields such as catalyst, semiconductors and dielectrics. SrTiO3 is a typical perovskite-type oxide, the physical properties of which strongly depend on its chemical composition, structure, shape, size, and crystallinity. In this work, the effects of Bi(Mg1/2Ti1/2)O3 addition on the nanostructure and the dielectric properties of Si-Mn modified SrTiO3 were investigated to develop nano-sized particles and low-temperature-fired SrTiO3-based ceramics with stable temperature characteristics. The dielectric constant of SrTiO3-Bi(Mg1/2Ti1/2)O3 was found to range from 900 to 1200 at 1 kHz for samples sintered at 1200°C. This new composition, SrTiO3-Bi(Mg1/2Ti1/2)O3, can be applied as a nano-sized dielectric materials in various fields.

Atlantic salmon (Salmo salar) require increased dietary levels of B-vitamins when fed diets with high inclusion of plant based ingredients

PubMed Central

Lock, Erik-Jan; Olsvik, Pål Asgeir; Hamre, Kristin; Espe, Marit; Torstensen, Bente Elisabeth; Silva, Joana; Hansen, Ann-Cecilie; Waagbø, Rune; Johansen, Johan S.; Sanden, Monica; Sissener, Nini H.

2016-01-01

Aiming to re-evaluate current recommendations for nutrient supplementations when Atlantic salmon are fed diets based on plant ingredients, two regression experiments, with parr and post-smolt, were conducted. A control diet was included to evaluate if ingredients supplied sufficient nutrients without any added nutrient package (NP). The nutrient package consisted of vitamins B, C, E, minerals, cholesterol, methionine, taurine and histidine. This paper focus on B-vitamins. In parr, growth, health and welfare parameters responded on NP additions, but this was not observed in the seawater stage. During three months of feeding, parr tripled their weight. Parr given diets added the NP above NRC (2011) showed improved protein retention, and reduced liver and viscera indices. Post-smolt fed the same diets during five months showed a doubling of weight, but did not respond to the variation in NP to the same extent as parr. Significant regressions were obtained in body compartments for several of the B-vitamins in the premix. Whole body biotin concentration was unaffected by micronutrient premix level, and mRNA expression of the enzymes dependent of biotin showed only weak increases with increased biotin. Muscle thiamine plateaued at a diet level similar to NRC (2011) recommendation in freshwater, and showed stable values independent on premix addition in seawater. The mRNA expression of the enzyme G6PDH (glucose-6-phosphate dehydrogenase) is sensitive to thiamine availability; results did not indicate any need to add thiamine above levels recommended for fish in general. Niacin showed a steady increase in whole body concentrations as feed niacin increased. Muscle riboflavin peaked at a diet level of 12.4 mg kg−1. Sufficient riboflavin is important to avoid e.g., development of cataract. Cataract was not registered to be any problem, neither in fresh- nor in seawater. Cobalamin (B 12) in muscle and liver was saturated at 0.17 mg kg−1 diet. Muscle pyridoxine showed a dose-dependent level in muscle, and peaked around 10 mg kg −1 diet. White muscle ASAT (asparagine amino transferase) activity steadily increased, with indications of stable values when dietary pyridoxine was around 10–16 mg kg −1 diet. Pantothenic acid increased in gill tissue up to a level of 5.5 mg kg −1 soft gill tissue; at a dietary level of 22 mg kg−1. Improved performance, and coverage of metabolic need for niacin was at a dietary level of 66 mg kg −1, riboflavin 10–12 mg kg−1, pyridoxine 10 mg kg−1 and panthotenic acid 22 mg kg−1. Based on these results, recommended B-vitamin supplementation in plant based diets for Atlantic salmon should be adjusted. PMID:27703849

Mechanical property, biocorrosion and in vitro biocompatibility evaluations of Mg-Li-(Al)-(RE) alloys for future cardiovascular stent application.

PubMed

Zhou, W R; Zheng, Y F; Leeflang, M A; Zhou, J

2013-11-01

Mg-Li-based alloys were investigated for future cardiovascular stent application as they possess excellent ductility. However, Mg-Li binary alloys exhibited reduced mechanical strengths due to the presence of lithium. To improve the mechanical strengths of Mg-Li binary alloys, aluminum and rare earth (RE) elements were added to form Mg-Li-Al ternary and Mg-Li-Al-RE quarternary alloys. In the present study, six Mg-Li-(Al)-(RE) alloys were fabricated. Their microstructures, mechanical properties and biocorrosion behavior were evaluated by using optical microscopy, X-ray diffraction, scanning electronic microscopy, tensile tests, immersion tests and electrochemical measurements. Microstructure characterization indicated that grain sizes were moderately refined by the addition of rare earth elements. Tensile testing showed that enhanced mechanical strengths were obtained, while electrochemical and immersion tests showed reduced corrosion resistance caused by intermetallic compounds distributed throughout the magnesium matrix in the rare-earth-containing Mg-Li alloys. Cytotoxicity assays, hemolysis tests as well as platelet adhesion tests were performed to evaluate in vitro biocompatibilities of the Mg-Li-based alloys. The results of cytotoxicity assays clearly showed that the Mg-3.5Li-2Al-2RE, Mg-3.5Li-4Al-2RE and Mg-8.5Li-2Al-2RE alloys suppressed vascular smooth muscle cell proliferation after 5day incubation, while the Mg-3.5Li, Mg-8.5Li and Mg-8.5Li-1Al alloys were proven to be tolerated. In the case of human umbilical vein endothelial cells, the Mg-Li-based alloys showed no significantly reduced cell viabilities except for the Mg-8.5Li-2Al-2RE alloy, with no obvious differences in cell viability between different culture periods. With the exception of Mg-8.5Li-2Al-2RE, all of the other Mg-Li-(Al)-(RE) alloys exhibited acceptable hemolysis ratios, and no sign of thrombogenicity was found. These in vitro experimental results indicate the potential of Mg-Li-(Al)-(RE) alloys as biomaterials for future cardiovascular stent application and the worthiness of investigating their biodegradation behaviors in vivo. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Polyurethane foam with multi walled carbon nanotubes/magnesium hybrid filler

NASA Astrophysics Data System (ADS)

Adnan, Sinar Arzuria; Zainuddin, Firuz; Zaidi, Nur Hidayah Ahmad; Akil, Hazizan Md.; Ahmad, Sahrim

2016-07-01

The purpose of this paper is to investigate the effect of multiwalled carbon nanotubes (MWCNTs)/magnesium (Mg) hybrid filler in polyurethane (PU) foams with different weight percentages (0.5 wt.% to 3.0 wt.%). The PU/MWCNTs/Mg foam composites were formed by reaction of based palm oil polyol (POP) with methylene diphenyl diisocyanate (MDI) with ratio 1:1.1 by weight. The foam properties were evaluated in density, morphology and compressive strength. The addition of 2.5 wt.% hybrid filler showed the higher density in 59.72 kg/m3 and thus contribute to the highest compressive strength at 1.76 MPa. The morphology show cell in closed structure and addition hybrid filler showed uneven structure.

An In Vitro Mechanism Study on the Proliferation and Pluripotency of Human Embryonic Stems Cells in Response to Magnesium Degradation

PubMed Central

Nguyen, Thanh Yen; Liew, Chee Gee; Liu, Huinan

2013-01-01

Magnesium (Mg) is a promising biodegradable metallic material for applications in cellular/tissue engineering and biomedical implants/devices. To advance clinical translation of Mg-based biomaterials, we investigated the effects and mechanisms of Mg degradation on the proliferation and pluripotency of human embryonic stem cells (hESCs). We used hESCs as the in vitro model system to study cellular responses to Mg degradation because they are sensitive to toxicants and capable of differentiating into any cell types of interest for regenerative medicine. In a previous study when hESCs were cultured in vitro with either polished metallic Mg (99.9% purity) or pre-degraded Mg, cell death was observed within the first 30 hours of culture. Excess Mg ions and hydroxide ions induced by Mg degradation may have been the causes for the observed cell death; hence, their respective effects on hESCs were investigated for the first time to reveal the potential mechanisms. For this purpose, the mTeSR®1 hESC culture media was either modified to an alkaline pH of 8.1 or supplemented with 0.4–40 mM of Mg ions. We showed that the initial increase of media pH to 8.1 had no adverse effect on hESC proliferation. At all tested Mg ion dosages, the hESCs grew to confluency and retained pluripotency as indicated by the expression of OCT4, SSEA3, and SOX2. When the supplemental Mg ion dosages increased to greater than 10 mM, however, hESC colony morphology changed and cell counts decreased. These results suggest that Mg-based implants or scaffolds are promising in combination with hESCs for regenerative medicine applications, providing their degradation rate is moderate. Additionally, the hESC culture system could serve as a standard model for cytocompatibility studies of Mg in vitro, and an identified 10 mM critical dosage of Mg ions could serve as a design guideline for safe degradation of Mg-based implants/scaffolds. PMID:24146887

A combined toxicity study of zinc oxide nanoparticles and vitamin C in food additives

NASA Astrophysics Data System (ADS)

Wang, Yanli; Yuan, Lulu; Yao, Chenjie; Ding, Lin; Li, Chenchen; Fang, Jie; Sui, Keke; Liu, Yuanfang; Wu, Minghong

2014-11-01

At present, safety evaluation standards for nanofood additives are made based on the toxic effects of a single additive. Since the size, surface properties and chemical nature influence the toxicity of nanomaterials, the toxicity may have dramatically changed when nanomaterials are used as food additives in a complex system. Herein, we investigated the combined toxicity of zinc oxide nanoparticles (ZnO NPs) and vitamin C (Vc, ascorbic acid). The results showed that Vc increased the cytotoxicity significantly compared with that of the ZnO only NPs. When the cells were exposed to ZnO NPs at a concentration less than 15 mg L-1, or to Vc at a concentration less than 300 mg L-1, there was no significant cytotoxicity, both in the case of gastric epithelial cell line (GES-1) and neural stem cells (NSCs). However, when 15 mg L-1 of ZnO NPs and 300 mg L-1 of Vc were introduced to cells together, the cell viability decreased sharply indicating significant cytotoxicity. Moreover, the significant increase in toxicity was also shown in the in vivo experiments. The dose of the ZnO NPs and Vc used in the in vivo study was calculated according to the state of food and nutrition enhancer standard. After repeated oral exposure to ZnO NPs plus Vc, the injury of the liver and kidneys in mice has been indicated by the change of these indices. These findings demonstrate that the synergistic toxicity presented in a complex system is essential for the toxicological evaluation and safety assessment of nanofood.At present, safety evaluation standards for nanofood additives are made based on the toxic effects of a single additive. Since the size, surface properties and chemical nature influence the toxicity of nanomaterials, the toxicity may have dramatically changed when nanomaterials are used as food additives in a complex system. Herein, we investigated the combined toxicity of zinc oxide nanoparticles (ZnO NPs) and vitamin C (Vc, ascorbic acid). The results showed that Vc increased the cytotoxicity significantly compared with that of the ZnO only NPs. When the cells were exposed to ZnO NPs at a concentration less than 15 mg L-1, or to Vc at a concentration less than 300 mg L-1, there was no significant cytotoxicity, both in the case of gastric epithelial cell line (GES-1) and neural stem cells (NSCs). However, when 15 mg L-1 of ZnO NPs and 300 mg L-1 of Vc were introduced to cells together, the cell viability decreased sharply indicating significant cytotoxicity. Moreover, the significant increase in toxicity was also shown in the in vivo experiments. The dose of the ZnO NPs and Vc used in the in vivo study was calculated according to the state of food and nutrition enhancer standard. After repeated oral exposure to ZnO NPs plus Vc, the injury of the liver and kidneys in mice has been indicated by the change of these indices. These findings demonstrate that the synergistic toxicity presented in a complex system is essential for the toxicological evaluation and safety assessment of nanofood. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr05480f

Impact of Phosphorus-Based Food Additives on Bone and Mineral Metabolism.

PubMed

Gutiérrez, Orlando M; Luzuriaga-McPherson, Alexandra; Lin, Yiming; Gilbert, Linda C; Ha, Shin-Woo; Beck, George R

2015-11-01

Phosphorus-based food additives can substantially increase total phosphorus intake per day, but the effect of these additives on endocrine factors regulating bone and mineral metabolism is unclear. This study aimed to examine the effect of phosphorus additives on markers of bone and mineral metabolism. Design and Setting, and Participants: This was a feeding study of 10 healthy individuals fed a diet providing ∼1000 mg of phosphorus/d using foods known to be free of phosphorus additives for 1 week (low-additive diet), immediately followed by a diet containing identical food items; however, the foods contained phosphorus additives (additive-enhanced diet). Parallel studies were conducted in animals fed low- (0.2%) and high- (1.8%) phosphorus diets for 5 or 15 weeks. The changes in markers of mineral metabolism after each diet period were measured. Participants were 32 ± 8 years old, 30% male, and 70% black. The measured phosphorus content of the additive-enhanced diet was 606 ± 125 mg higher than the low-additive diet (P < .001). After 1 week of the low-additive diet, consuming the additive-enhanced diet for 1 week significantly increased circulating fibroblast growth factor 23 (FGF23), osteopontin, and osteocalcin concentrations by 23, 10, and 11%, respectively, and decreased mean sclerostin concentrations (P < .05 for all). Similarly, high-phosphorus diets in mice significantly increased blood FGF23, osteopontin and osteocalcin, lowered sclerostin, and decreased bone mineral density (P < .05 for all). The enhanced phosphorus content of processed foods can disturb bone and mineral metabolism in humans. The results of the animal studies suggest that this may compromise bone health.

Role of chemical interaction between MgH2 and TiO2 additive on the hydrogen storage behavior of MgH2

NASA Astrophysics Data System (ADS)

Pukazhselvan, D.; Nasani, Narendar; Sandhya, K. S.; Singh, Budhendra; Bdikin, Igor; Koga, Nobuaki; Fagg, Duncan Paul

2017-10-01

The present study explores how the additive titania chemically reacts with magnesium hydride and influences the dehydrogenation of MgH2. Quantitative X - ray diffraction study of ball milled MgH2 + xTiO2 (x = 0.25, 0.33, 0.5 and 1) suggests that Ti substituted MgO is the main reaction product in all the product powders. Convincing evidence is obtained to conclude that Ti dissolution in MgO makes a dramatic behavioral change to MgO; passive MgO turns as an active in-built catalyst. The analysis correlating the dehydrogenation kinetics, composition of in-situ catalyst and sample durability suggests that effectiveness of Ti substituted MgO (MgxTiyOx+y) as a catalyst for MgH2 depends on the concentration of Ti in MgxTiyOx+y rock salt. These observations are immensely helpful for understanding the hydrogen desorption mechanism of metal oxide additives loaded MgH2 system.

Minimization of Hypoglycemia as an Adverse Event During Insulin Infusion: Further Refinement of the Yale Protocol.

PubMed

Marvin, Michael R; Inzucchi, Silvio E; Besterman, Brian J

2016-08-01

The management of hyperglycemia in the intensive care unit has been a controversial topic for more than a decade, with target ranges varying from 80-110 mg/dL to <200 mg/dL. Multiple insulin infusion protocols exist, including several computerized protocols, which have attempted to achieve these targets. Importantly, compliance with these protocols has not been a focus of clinical studies. GlucoCare™, a Food and Drug Administration (FDA)-cleared insulin-dosing calculator, was originally designed based on the Yale Insulin Infusion Protocol to target 100-140 mg/dL and has undergone several modifications to reduce hypoglycemia. The original Yale protocol was modified from 100-140 mg/dL to a range of 120-140 mg/dL (GlucoCare 120-140) and then to 140 mg/dL (GlucoCare 140, not a range but a single blood glucose [BG] level target) in an iterative and evidence-based manner to eliminate hypoglycemia <70 mg/dL. The final modification [GlucoCare 140(B)] includes the addition of bolus insulin "midprotocol" during an insulin infusion to reduce peak insulin rates for insulin-resistant patients. This study examined the results of these protocol modifications and evaluated the role of compliance with the protocol in the incidence of hypoglycemia <70 mg/dL. Protocol modifications resulted in mean BG levels of 133.4, 136.4, 143.8, and 146.4 mg/dL and hypoglycemic BG readings <70 mg/dL of 0.998%, 0.367%, 0.256%, and 0.04% for the 100-140, 120-140, 140, and 140(B) protocols, respectively (P < 0.001). Adherence to the glucose check interval significantly reduced the incidence of hypoglycemia (P < 0.001). Protocol modifications led to a reduction in peak insulin infusion rates (P < 0.001) and the need for dextrose-containing boluses (P < 0.001). This study demonstrates that refinements in protocol design can improve glucose control in critically ill patients and that the use of GlucoCare 140(B) can eliminate all significant hypoglycemia while achieving mean glucose levels between 140 and 150 mg/dL. In addition, attention to the timely performance of glucose levels can also reduce hypoglycemic events.

Laccase-catalyzed decolorization of malachite green: performance optimization and degradation mechanism.

PubMed

Yang, Jie; Yang, Xiaodan; Lin, Yonghui; Ng, Tzi Bun; Lin, Juan; Ye, Xiuyun

2015-01-01

Malachite green (MG) was decolorized by laccase (LacA) of white-rot fungus Cerrena sp. with strong decolorizing ability. Decolorization conditions were optimized with response surface methodology. A highly significant quadratic model was developed to investigate MG decolorization with LacA, and the maximum MG decolorization ratio of 91.6% was predicted under the conditions of 2.8 U mL(-1) LacA, 109.9 mg L(-1) MG and decolorization for 172.4 min. Kinetic studies revealed the Km and kcat values of LacA toward MG were 781.9 mM and 9.5 s(-1), respectively. UV-visible spectra confirmed degradation of MG, and the degradation mechanism was explored with liquid chromatography-mass spectrometry (LC-MS) analysis. Based on the LC-MS spectra of degradation products, LacA catalyzed MG degradation via two simultaneous pathways. In addition, the phytotoxicity of MG, in terms of inhibition on seed germination and seedling root elongation of Nicotiana tabacum and Lactuca sativa, was reduced after laccase treatment. These results suggest that laccase of Cerrena was effective in decolorizing MG and promising in bioremediation of wastewater in food and aquaculture industries.

Laccase-Catalyzed Decolorization of Malachite Green: Performance Optimization and Degradation Mechanism

PubMed Central

Yang, Jie; Yang, Xiaodan; Lin, Yonghui; Ng, Tzi Bun; Lin, Juan; Ye, Xiuyun

2015-01-01

Malachite green (MG) was decolorized by laccase (LacA) of white-rot fungus Cerrena sp. with strong decolorizing ability. Decolorization conditions were optimized with response surface methodology. A highly significant quadratic model was developed to investigate MG decolorization with LacA, and the maximum MG decolorization ratio of 91.6% was predicted under the conditions of 2.8 U mL-1 LacA, 109.9 mg L-1 MG and decolorization for 172.4 min. Kinetic studies revealed the Km and kcat values of LacA toward MG were 781.9 mM and 9.5 s-1, respectively. UV–visible spectra confirmed degradation of MG, and the degradation mechanism was explored with liquid chromatography–mass spectrometry (LC-MS) analysis. Based on the LC-MS spectra of degradation products, LacA catalyzed MG degradation via two simultaneous pathways. In addition, the phytotoxicity of MG, in terms of inhibition on seed germination and seedling root elongation of Nicotiana tabacum and Lactuca sativa, was reduced after laccase treatment. These results suggest that laccase of Cerrena was effective in decolorizing MG and promising in bioremediation of wastewater in food and aquaculture industries. PMID:26020270

Biodegradable Orthopedic Magnesium-Calcium (MgCa) Alloys, Processing, and Corrosion Performance.

PubMed

Salahshoor, Meisam; Guo, Yuebin

2012-01-09

Magnesium-Calcium (Mg-Ca) alloy has received considerable attention as an emerging biodegradable implant material in orthopedic fixation applications. The biodegradable Mg-Ca alloys avoid stress shielding and secondary surgery inherent with permanent metallic implant materials. They also provide sufficient mechanical strength in load carrying applications as opposed to biopolymers. However, the key issue facing a biodegradable Mg-Ca implant is the fast corrosion in the human body environment. The ability to adjust degradation rate of Mg-Ca alloys is critical for the successful development of biodegradable orthopedic implants. This paper focuses on the functions and requirements of bone implants and critical issues of current implant biomaterials. Microstructures and mechanical properties of Mg-Ca alloys, and the unique properties of novel magnesium-calcium implant materials have been reviewed. Various manufacturing techniques to process Mg-Ca based alloys have been analyzed regarding their impacts on implant performance. Corrosion performance of Mg-Ca alloys processed by different manufacturing techniques was compared. In addition, the societal and economical impacts of developing biodegradable orthopedic implants have been emphasized.

Crystal Analysis of Multi Phase Calcium Phosphate Nanoparticles Containing Different amount of Magnesium

NASA Astrophysics Data System (ADS)

Gozalian, Afsaneh; Behnamghader, Ali Asghar; Moshkforoush, Arash

In this study, Mg doped hydroxyapatite [(Ca, Mg)10(PO4)6(OH)2] and β-tricalcium phosphate nanoparticles were synthesized via sol gel method. Triethyl phosphite, calcium nitrate tetrahydrate and magnesium nitrate hexahydrate were used as P, Ca and Mg precursors. The ratio of (Ca+Mg)/P and the amount of magnesium (x) were kept constant at 1.67 and ranging x = 0 up to 3 in molecular formula of Ca10-xMgx (PO4)6(OH)2, respectively. Phase composition and chemical structure were performed using X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). Phase percentages, crystallite size, degree of crystallinity and lattice parameters were investigated. The presence of magnesium led to form the Mg doped tricalcium phosphate (β-TCMP) and Mg doped hydroxyapatite (Mg-HA). Based on the results of this study, lattice parameters, degree of crystallinity and crystallite size decreased with magnesium content. In addition, with increasing magnesium content, the amount of CaO phase decreased whereas the amount of MgO phase increased significantly. Obtained results can be used for new biomaterials design.

Biodegradable Orthopedic Magnesium-Calcium (MgCa) Alloys, Processing, and Corrosion Performance

PubMed Central

Salahshoor, Meisam; Guo, Yuebin

2012-01-01

Magnesium-Calcium (Mg-Ca) alloy has received considerable attention as an emerging biodegradable implant material in orthopedic fixation applications. The biodegradable Mg-Ca alloys avoid stress shielding and secondary surgery inherent with permanent metallic implant materials. They also provide sufficient mechanical strength in load carrying applications as opposed to biopolymers. However, the key issue facing a biodegradable Mg-Ca implant is the fast corrosion in the human body environment. The ability to adjust degradation rate of Mg-Ca alloys is critical for the successful development of biodegradable orthopedic implants. This paper focuses on the functions and requirements of bone implants and critical issues of current implant biomaterials. Microstructures and mechanical properties of Mg-Ca alloys, and the unique properties of novel magnesium-calcium implant materials have been reviewed. Various manufacturing techniques to process Mg-Ca based alloys have been analyzed regarding their impacts on implant performance. Corrosion performance of Mg-Ca alloys processed by different manufacturing techniques was compared. In addition, the societal and economical impacts of developing biodegradable orthopedic implants have been emphasized. PMID:28817036

Development of novel therapies for MG: Studies in animal models.

PubMed

Souroujon, M C; Brenner, T; Fuchs, S

2010-08-01

Experimental myasthenia gravis (MG) in animals, and in particular experimental autoimmune MG in rodents, serves as excellent models to study possible novel therapeutic modalities for MG. The current treatments for MG are based on cholinesterase inhibitors, general immunosuppressants, and corticosteroids, broad immunomodulatory therapies such as plasma exchange or intravenous immunoglobulins (IVIGs), and thymectomy for selected patients. This stresses the need for immunotherapies that would specifically or preferentially suppress the undesirable autoimmune response without widely affecting the entire immune system as most available treatments do. The available animal models for MG enable to perform preclinical studies in which novel therapeutic approaches can be tested. In this review, we describe the different therapeutic approaches that were so far tested in experimental models of MG and discuss their underlying mechanisms of action. These include antigen - acetylcholine receptor (AChR)-dependent treatments aimed at specifically abrogating the humoral and cellular anti-AChR responses as well as immunomodulatory approaches that could be used either alone or in conjunction with antigen-specific treatments or alternatively serve as steroid sparing agents. The antigen-specific treatments are based on fragments or peptides derived from the acetylcholine receptor (AChR) that would theoretically deviate the anti-AChR autoimmune response away from the muscle target or on ways to target AChR-specific T- and B- cell responses or antibodies. The immunomodulatory modalities include cell-based and non-cell-based ways to affect or manipulate key players in the autoimmune process such as regulatory T cells, dendritic cells, cytokine networks, and chemokine and costimulatory signaling as well as complement pathways. We also describe approaches that attempt to affect the cholinergic balance, which is impaired at the neuromuscular junction. In addition to enabling to test the feasibility of novel approaches, experimental MG enables to perform analyses of existing treatment modalities, which cannot be performed in human MG patients. These include studies on the mode of action of various immunosuppressants and on IVIGs. Hopefully, the vast repertoire of therapeutic approaches that are studied in experimental models of MG will pave the way to clinical studies that will eventually improve the management of MG.

Ionic Liquid as an Effective Additive for Rechargeable Magnesium Batteries

DOE PAGES

Pan, Baofei; Lau, Ka -Cheong; Vaughey, John T.; ...

2017-03-02

Here, the effect of the addition of an ionic liquid DEME•TFSI to an electrolyte solution of Mg(HMDS) 2-MgCl 2 in THF was studied electrochemically and spectroscopically. Reversible magnesium deposition/dissolution was achieved with the DEME•TFSI-modified electrolyte. This electrolyte shows higher ionic conductivity, and a linear relationship was observed between the ionic conductivity and the concentration of DEME•TFSI in THF solution of Mg(HMDS) 2-MgCl 2. Mg-Mo 6S 8 coin cells have also been successfully cycled using Mg(HMDS) 2-MgCl 2 electrolyte with the addition of DEME•TFSI. Raman and NMR spectroscopy suggest that DEME•TFSI facilitates magnesium deposition/dissolution by improving ionic conductivity of the electrolyte.

Properties of transparent (Gd,Lu)3(Al,Ga)5O12:Ce ceramic with Mg, Ca and Ce co-dopants

NASA Astrophysics Data System (ADS)

Wang, Yimin; Baldoni, Gary; Brecher, Charles; Rhodes, William H.; Shirwadkar, Urmila; Glodo, Jarek; Shah, Ishaan; Ji, Chuncheng

2015-08-01

Cerium activated mixed lutetium/gadolinium- and aluminum/gallium-based garnets have great potential as host scintillators for medical imaging applications. (Gd,Lu)3(Al,Ga)5O12:Ce and denoted as GLuGAG feature high effective atomic number and good light yield, which make it particularly attractive for Positron Emission Tomography (PET) and other γ-ray detection applications. For PET application, rapid decay and good timing resolution are extremely important. Most Ce-doped mixed garnet materials such as GLuGAG:Ce, have their main decay component at around 80 ns. However, it has been reported that the decays of some single crystal scintillators (e.g., LSO and GGAG) can be effectively accelerated by codoping with selected additives such as Ca, Mg and B. In this study, transparent polycrystalline (Gd,Lu)3(Al,Ga)5O12:Ce ceramics codoped with Ca or Mg or additional Ce, were fabricated by the sinter-HIP approach. It was found the transmission of the ceramics are closely related to the microstructure of the ceramics. As the co-dopant levels increase, 2nd phase occurs in the ceramic and thus transparency of the ceramic decreases. Ca and Mg co-doping in GLuGAG:Ce ceramic effectively accelerate decays of GLuGAG:Ce ceramics at a cost of light output. However, additional Ce doping in the GLuGAG:Ce has no benefit on improving decay time but, on the other hand, reduces transmission, light output. The mechanism under the different scintillation behaviors with Mg, Ca and Ce dopants are discussed. The results suggest that decay time of GLuGAG:Ce ceramics can be effectively tailored by co-doping GLuGAG:Ce ceramic with Mg and Ca for applications with optimal timing resolution.

Enhanced luminescence in SrMgAl(x)O(17±δ):yMn4+ composite phosphors.

PubMed

Cao, Renping; Sharafudeen, Kaniyarakkal N; Qiu, Jianrong

2014-01-03

Red-emitting SrMgAlxO17±δ:yMn(4+) composite phosphors (x=10-100; y=0.05-4.0 mol%) are synthesized by solid-state reaction method in air. Addition of Al2O3 leads to the formation of two concomitant phases, i.e., SrMgAl10O17 and Al2O3 phases in the composite phosphor. Red emission from Mn(4+) ions in the composite phosphors is greatly enhanced due to multiple scattering and absorption of excitation light between SrMgAl10O17 and Al2O3 phases. SrMgAlxO17±δ:yMn(4+) composite phosphors would be a promising candidate as red phosphor in the application of a 397 nm near UV-based W-LED. Copyright © 2013 Elsevier B.V. All rights reserved.

Outcome Measures in Myasthenia Gravis: Incorporation Into Clinical Practice.

PubMed

Muppidi, Srikanth

2017-03-01

The development of validated assessment tools for evaluating disease status and response to interventions in patients with myasthenia gravis (MG) has been driven by clinical studies of emerging MG therapies. However, only a small proportion of MG-focused neurology practices have adopted these assessment tools for routine clinical use. This article reviews the suitability of 5 assessment instruments for incorporation into clinical practice, which should be driven by their ability to contribute to improved patient outcomes, and to be implemented within practice personnel and resource constraints. It is recommended that assessments based on both physician-evaluated and patient-reported outcomes be selected, to adequately evaluate both point-in-time symptom load and functional impact of MG symptoms over time. Provider resource allocation and reimbursement issues may be the most significant roadblocks to successful ongoing use of these tools; to that end, the addition of regular assessments to MG standards of care is recommended.

Prehospital Care for the Adult and Pediatric Seizure Patient: Current Evidence-based Recommendations.

PubMed

Silverman, Eric C; Sporer, Karl A; Lemieux, Justin M; Brown, John F; Koenig, Kristi L; Gausche-Hill, Marianne; Rudnick, Eric M; Salvucci, Angelo A; Gilbert, Greg H

2017-04-01

We sought to develop evidence-based recommendations for the prehospital evaluation and treatment of adult and pediatric patients with a seizure and to compare these recommendations against the current protocol used by the 33 emergency medical services (EMS) agencies in California. We performed a review of the evidence in the prehospital treatment of patients with a seizure, and then compared the seizure protocols of each of the 33 EMS agencies for consistency with these recommendations. We analyzed the type and route of medication administered, number of additional rescue doses permitted, and requirements for glucose testing prior to medication. The treatment for eclampsia and seizures in pediatric patients were analyzed separately. Protocols across EMS Agencies in California varied widely. We identified multiple drugs, dosages, routes of administration, re-dosing instructions, and requirement for blood glucose testing prior to medication delivery. Blood glucose testing prior to benzodiazepine administration is required by 61% (20/33) of agencies for adult patients and 76% (25/33) for pediatric patients. All agencies have protocols for giving intramuscular benzodiazepines and 76% (25/33) have protocols for intranasal benzodiazepines. Intramuscular midazolam dosages ranged from 2 to 10 mg per single adult dose, 2 to 8 mg per single pediatric dose, and 0.1 to 0.2 mg/kg as a weight-based dose. Intranasal midazolam dosages ranged from 2 to 10 mg per single adult or pediatric dose, and 0.1 to 0.2 mg/kg as a weight-based dose. Intravenous/intrasosseous midazolam dosages ranged from 1 to 6 mg per single adult dose, 1 to 5 mg per single pediatric dose, and 0.05 to 0.1 mg/kg as a weight-based dose. Eclampsia is specifically addressed by 85% (28/33) of agencies. Forty-two percent (14/33) have a protocol for administering magnesium sulfate, with intravenous dosages ranging from 2 to 6 mg, and 58% (19/33) allow benzodiazepines to be administered. Protocols for a patient with a seizure, including eclampsia and febrile seizures, vary widely across California. These recommendations for the prehospital diagnosis and treatment of seizures may be useful for EMS medical directors tasked with creating and revising these protocols.

Mg2+ in the Major Groove Modulates B-DNA Structure and Dynamics

PubMed Central

Guéroult, Marc; Boittin, Olivier; Mauffret, Oliver; Etchebest, Catherine; Hartmann, Brigitte

2012-01-01

This study investigates the effect of Mg2+ bound to the DNA major groove on DNA structure and dynamics. The analysis of a comprehensive dataset of B-DNA crystallographic structures shows that divalent cations are preferentially located in the DNA major groove where they interact with successive bases of (A/G)pG and the phosphate group of 5′-CpA or TpG. Based on this knowledge, molecular dynamics simulations were carried out on a DNA oligomer without or with Mg2+ close to an ApG step. These simulations showed that the hydrated Mg2+ forms a stable intra-strand cross-link between the two purines in solution. ApG generates an electrostatic potential in the major groove that is particularly attractive for cations; its intrinsic conformation is well-adapted to the formation of water-mediated hydrogen bonds with Mg2+. The binding of Mg2+ modulates the behavior of the 5′-neighboring step by increasing the BII (ε-ζ>0°) population of its phosphate group. Additional electrostatic interactions between the 5′-phosphate group and Mg2+ strengthen both the DNA-cation binding and the BII character of the 5′-step. Cation binding in the major groove may therefore locally influence the DNA conformational landscape, suggesting a possible avenue for better understanding how strong DNA distortions can be stabilized in protein-DNA complexes. PMID:22844516

Sifalimumab, an anti-interferon-α monoclonal antibody, in moderate to severe systemic lupus erythematosus: a randomised, double-blind, placebo-controlled study.

PubMed

Khamashta, Munther; Merrill, Joan T; Werth, Victoria P; Furie, Richard; Kalunian, Kenneth; Illei, Gabor G; Drappa, Jorn; Wang, Liangwei; Greth, Warren

2016-11-01

The efficacy and safety of sifalimumab were assessed in a phase IIb, randomised, double-blind, placebo-controlled study (NCT01283139) of adults with moderate to severe active systemic lupus erythematosus (SLE). 431 patients were randomised and received monthly intravenous sifalimumab (200 mg, 600 mg or 1200 mg) or placebo in addition to standard-of-care medications. Patients were stratified by disease activity, interferon gene-signature test (high vs low based on the expression of four genes) and geographical region. The primary efficacy end point was the percentage of patients achieving an SLE responder index response at week 52. Compared with placebo, a greater percentage of patients who received sifalimumab (all dosages) met the primary end point (placebo: 45.4%; 200 mg: 58.3%; 600 mg: 56.5%; 1200 mg 59.8%). Other improvements were seen in Cutaneous Lupus Erythematosus Disease Area and Severity Index score (200 mg and 1200 mg monthly), Physician's Global Assessment (600 mg and 1200 mg monthly), British Isles Lupus Assessment Group-based Composite Lupus Assessment (1200 mg monthly), 4-point reductions in the SLE Disease Activity Index-2000 score and reductions in counts of swollen joints and tender joints. Serious adverse events occurred in 17.6% of patients on placebo and 18.3% of patients on sifalimumab. Herpes zoster infections were more frequent with sifalimumab treatment. Sifalimumab is a promising treatment for adults with SLE. Improvement was consistent across various clinical end points, including global and organ-specific measures of disease activity. NCT01283139; Results. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Sifalimumab, an anti-interferon-α monoclonal antibody, in moderate to severe systemic lupus erythematosus: a randomised, double-blind, placebo-controlled study

PubMed Central

Khamashta, Munther; Merrill, Joan T; Werth, Victoria P; Furie, Richard; Kalunian, Kenneth; Illei, Gabor G; Drappa, Jorn; Wang, Liangwei; Greth, Warren

2016-01-01

Objectives The efficacy and safety of sifalimumab were assessed in a phase IIb, randomised, double-blind, placebo-controlled study (NCT01283139) of adults with moderate to severe active systemic lupus erythematosus (SLE). Methods 431 patients were randomised and received monthly intravenous sifalimumab (200 mg, 600 mg or 1200 mg) or placebo in addition to standard-of-care medications. Patients were stratified by disease activity, interferon gene-signature test (high vs low based on the expression of four genes) and geographical region. The primary efficacy end point was the percentage of patients achieving an SLE responder index response at week 52. Results Compared with placebo, a greater percentage of patients who received sifalimumab (all dosages) met the primary end point (placebo: 45.4%; 200 mg: 58.3%; 600 mg: 56.5%; 1200 mg 59.8%). Other improvements were seen in Cutaneous Lupus Erythematosus Disease Area and Severity Index score (200 mg and 1200 mg monthly), Physician's Global Assessment (600 mg and 1200 mg monthly), British Isles Lupus Assessment Group-based Composite Lupus Assessment (1200 mg monthly), 4-point reductions in the SLE Disease Activity Index−2000 score and reductions in counts of swollen joints and tender joints. Serious adverse events occurred in 17.6% of patients on placebo and 18.3% of patients on sifalimumab. Herpes zoster infections were more frequent with sifalimumab treatment. Conclusions Sifalimumab is a promising treatment for adults with SLE. Improvement was consistent across various clinical end points, including global and organ-specific measures of disease activity. Trial registration number NCT01283139; Results. PMID:27009916

Competitive Heterogeneous Nucleation Between Zr and MgO Particles in Commercial Purity Magnesium

NASA Astrophysics Data System (ADS)

Peng, G. S.; Wang, Y.; Fan, Z.

2018-04-01

Grain refining of commercial purity (CP) Mg by Zr addition with intensive melt shearing prior to solidification has been investigated. Experimental results showed that, when intensive melt shearing is imposed prior to solidification, the grain structure of CP Mg exhibits a complex changing pattern with increasing Zr addition. This complex behavior can be attributed to the change of nucleating particles in terms of their crystal structure, size, and number density with varied Zr additions. Naturally occurring MgO particles are found to be {100} faceted with a cubic morphology and 50 to 300 nm in size. Such MgO particles are usually populated densely in a liquid film (usually referred as oxide film) and can be effectively dispersed by intensive melt shearing. It has been confirmed that the dispersed MgO particles can act as nucleating substrates resulting in a significant grain refinement of CP Mg when no other more potent particles are present in the melt. However, Zr particles in the Mg-Zr alloys are more potent than MgO particles for nucleation of Mg due to their same crystal structure and similar lattice parameters with Mg. With the addition of Zr, Zr and the MgO particles co-exist in the melt. Grain refining efficiency is closely related to the competition for heterogeneous nucleation between Zr and the MgO particles. The final solidified microstructure is mainly determined by the interplay of three factors: nucleation potency (measured by lattice misfit), particle size, and particle number density.

Competitive Heterogeneous Nucleation Between Zr and MgO Particles in Commercial Purity Magnesium

NASA Astrophysics Data System (ADS)

Peng, G. S.; Wang, Y.; Fan, Z.

2018-06-01

Grain refining of commercial purity (CP) Mg by Zr addition with intensive melt shearing prior to solidification has been investigated. Experimental results showed that, when intensive melt shearing is imposed prior to solidification, the grain structure of CP Mg exhibits a complex changing pattern with increasing Zr addition. This complex behavior can be attributed to the change of nucleating particles in terms of their crystal structure, size, and number density with varied Zr additions. Naturally occurring MgO particles are found to be {100} faceted with a cubic morphology and 50 to 300 nm in size. Such MgO particles are usually populated densely in a liquid film (usually referred as oxide film) and can be effectively dispersed by intensive melt shearing. It has been confirmed that the dispersed MgO particles can act as nucleating substrates resulting in a significant grain refinement of CP Mg when no other more potent particles are present in the melt. However, Zr particles in the Mg-Zr alloys are more potent than MgO particles for nucleation of Mg due to their same crystal structure and similar lattice parameters with Mg. With the addition of Zr, Zr and the MgO particles co-exist in the melt. Grain refining efficiency is closely related to the competition for heterogeneous nucleation between Zr and the MgO particles. The final solidified microstructure is mainly determined by the interplay of three factors: nucleation potency (measured by lattice misfit), particle size, and particle number density.

Fullerene C60 for enhancing phytoremediation of urea plant wastewater by timber plants.

PubMed

Yavari, Sara; Malakahmad, Amirhossein; Sapari, Nasiman B; Yavari, Saba

2018-04-01

Phytoremediation has been applied as a promising and cost-effective technique for removing nutrient pollutants from wastewater. In this study, the effect of fullerene C60 was assessed on enhancing the phytoremediation efficiency of teak plants over a period of 1 month. Teak plants were supplied with fullerene C60 (0, 25, or 50 mg L -1 ) and fed daily with two types of urea plant wastewater (with and without adding optimum ratio of phosphorus and potassium). The required volume of wastewater by the teak plants, nitrogen removal percentage, plant growth parameters (plant height, number of leaves, leaf surface area, and dry biomass), and nutrient content was recorded throughout the study. The results showed that addition of 25 mg L -1 fullerene C60 to urea plant wastewater could increase water uptake and nitrogen recovery of the teak plants. Plant growth and nutrient contents of teak plants were also increased in the presence of 25 mg L -1 fullerene C60. However, addition of 50 mg L -1 fullerene C60 to the wastewater decreased the values for water uptake and nitrogen recovery. The findings indicated that addition of proper amount of fullerene C60 to the teak-based remediation system can increase the efficiency of the plants for nitrogen removal.

Vacuolar transport of the glutathione conjugate of trans-cinnamic acid.

PubMed

Walczak, H A; Dean, J V

2000-02-01

Red beet (Beta vulgaris L.) tonoplast membrane vesicles and [14C]trans-cinnamic acid-glutatione were used to study the vacuolar transport of phynylpropanoid-glutathione conjugates which are formed in peroxidase-mediated reactions. It was determined that the uptake of [14C]trans-cinnamic acid-glutathione into the tonoplast membrane vesicles was MgATP dependent and was 10-fold faster than the uptake of non-conjugated [14C]trans-cinnamic acid. Uptake of the conjugate in the presence of MgATP was not dependent on a trans-tonoblast H+-electrochemical gradient, because uptake was not affected by the addition of NH4Cl (1 mM; 0% inhibition) and was only slightly affected by gramicidin-D (5 microM; 14% inhibition). Uptake of the conjugate was inhibited 92% by the addition of vanadate (1 mM) and 71% by the addition of the model substrate S-(2,4-dinitrophenyl) glutathione (500 microM). Uptake did not occur when a nonhydrolyzable analog of ATP was used in place of MgATP. The calculated Km and Vmax values for uptake were 142 microM amd 5.95 nmol mg(-1) min(-1), respectively. Based on these results, phenylpropanoid-glutation conjugates formed in peroxidase-mediated reactions appear to be transported into the vacuole by the glutathione S-conjugate pump(s) located in the tonoplast membrane.

Photocatalytic degradation of rhodamine B, paracetamol and diclofenac sodium by supported titania-based catalysts from petrochemical residue: effect of doping with magnesium.

PubMed

da Silva, William Leonardo; Lansarin, Marla Azário; Dos Santos, João Henrique Z; Silveira, Fernando

2016-11-01

Three different lots of a residual Ziegler-Natta catalyst slurry (bearing Ti and Mg) obtained from an industrial petrochemical plant were employed as sources for the photocatalyst supported on silica. The effect of additional magnesium (1.0-25.0 wt% Mg/SiO 2 ) on the photocatalytic properties of the doped materials was investigated. Doping the titania-based photocatalyst with Mg results in a shift in the absorption threshold toward the visible spectrum. The optical band gap energy of the bare supported photocatalyst was in the range of 2.5 eV and shifted to 1.72 eV after 25 wt% Mg doping. The systems were evaluated for the photodegradation of one dye (rhodamine B (RhB)) and two drugs (paracetamol and diclofenac sodium) either under ultraviolet (UV) (365 nm - UVA) or visible radiation, separately. Among the evaluated systems, doping with 25 wt% Mg afforded the highest degradation values for the target molecules under UV and visible radiation (i.e. 87%, 60% and 55% of the RhB, paracetamol and diclofenac under UV, respectively, and 82%, 48.3% and 48% under visible irradiation, respectively).

Milk protein composition and stability changes affected by iron in water sources.

PubMed

Wang, Aili; Duncan, Susan E; Knowlton, Katharine F; Ray, William K; Dietrich, Andrea M

2016-06-01

Water makes up more than 80% of the total weight of milk. However, the influence of water chemistry on the milk proteome has not been extensively studied. The objective was to evaluate interaction of water-sourced iron (low, medium, and high levels) on milk proteome and implications on milk oxidative state and mineral content. Protein composition, oxidative stability, and mineral composition of milk were investigated under conditions of iron ingestion through bovine drinking water (infused) as well as direct iron addition to commercial milk in 2 studies. Four ruminally cannulated cows each received aqueous infusions (based on water consumption of 100L) of 0, 2, 5, and 12.5mg/L Fe(2+) as ferrous lactate, resulting in doses of 0, 200, 500 or 1,250mg of Fe/d, in a 4×4Latin square design for a 14-d period. For comparison, ferrous sulfate solution was directly added into commercial retail milk at the same concentrations: control (0mg of Fe/L), low (2mg of Fe/L), medium (5mg of Fe/L), and high (12.5mg of Fe/L). Two-dimensional electrophoresis coupled with matrix-assisted laser desorption/ionization-tandem time-of-flight (MALDI-TOF/TOF) high-resolution tandem mass spectrometry analysis was applied to characterize milk protein composition. Oxidative stability of milk was evaluated by the thiobarbituric acid reactive substances (TBARS) assay for malondialdehyde, and mineral content was measured by inductively coupled plasma mass spectrometry. For milk from both abomasal infusion of ferrous lactate and direct addition of ferrous sulfate, an iron concentration as low as 2mg of Fe/L was able to cause oxidative stress in dairy cattle and infused milk, respectively. Abomasal infusion affected both caseins and whey proteins in the milk, whereas direct addition mainly influenced caseins. Although abomasal iron infusion did not significantly affect oxidation state and mineral balance (except iron), it induced oxidized off-flavor and partial degradation of whey proteins. Direct iron addition to milk led to lipid oxidation during storage at 4°C. Oxidation level was positively associated with the concentration of added iron. Minerals (Mg, P, Na, K, Ca, Zn) in milk were not affected by the added iron in milk. This study indicated that a small amount of iron contamination in bovine drinking water at the farm or incidental iron addition from potable water sources causes oxidation, affects milk protein composition and stability, and affects final milk quality. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Mechanical and Wear Properties of Sb- and Y-Added Mg-9Al-1Zn (AZ91) Alloy

NASA Astrophysics Data System (ADS)

Boby, Arun; Srinivasan, A.; Pillai, U. T. S.; Pai, B. C.

2015-09-01

This paper studies the effect of Sb and Y additions on the microstructure and mechanical properties of the AZ91 alloy. The results indicate that the Sb and Y additions lead to the formation of Mg3Sb2 and Al2Y phases. These phases modify the morphology of the β-Mg17Al12 phase, and hence refine the microstructure. The effects of Sb and Y additions on the aging behavior have also been investigated. Aging of the AZ91 alloy results in the formation of continuous and discontinuous types of precipitates. Whereas Sb and Y additions to AZ91 alloy suppresses the formation of discontinuous precipitate. The paper also reports the mechanical properties of as-cast and aged Sb-added AZ91-xY alloys for room and high temperatures. The optimum tensile properties are obtained with the alloy having the combined addition of 0.5 wt pct Sb and 0.6 wt pct Y. The fracture surface of AZ91-0.5Sb-0.6Y alloy reveals more quasi-cleavage type of failure with a cleavage fracture than the base alloy. At HT, the AZ91-0.5Sb-0.6Y alloy displays more cleavage facets connected with tearing ridges and shallow dimples than AZ91 alloy. Furthermore, it observed the improvement in wear resistance through the addition of Y. The worn surface reveals abrasion, oxidation, delamination, and plastic deformation wear mechanisms.

Formation of hydroxyapatite onto glasses of the CaO-MgO-SiO2 system with B2O3, Na2O, CaF2 and P2O5 additives.

PubMed

Agathopoulos, S; Tulyaganov, D U; Ventura, J M G; Kannan, S; Karakassides, M A; Ferreira, J M F

2006-03-01

New bioactive glasses with compositions based on the CaO-MgO-SiO(2) system and additives of B(2)O(3), P(2)O(5), Na(2)O, and CaF(2) were prepared. The in vitro mineralization behaviour was tested by immersion of powders or bulk glasses in simulated body fluid (SBF). Monitoring of ionic concentrations in SBF and scanning electron microscopy (SEM) observations at the surface of the glasses were conducted over immersion time. Raman and infrared (IR) spectroscopy shed light on the structural evolution occurring at the surface of the glasses that leads to formation of hydroxyapatite.

Characterization of micro-resonator based on enhanced metal insulator semiconductor capacitor for glucose recognition.

PubMed

Dhakal, Rajendra; Kim, E S; Jo, Yong-Hwa; Kim, Sung-Soo; Kim, Nam-Young

2017-03-01

We present a concept for the characterization of micro-fabricated based resonator incorporating air-bridge metal-insulator-semiconductor (MIS) capacitor to continuously monitor an individual's state of glucose levels based on frequency variation. The investigation revealed that, the micro-resonator based on MIS capacitor holds considerable promise for implementation and recognition as a glucose sensor for human serum. The discrepancy in complex permittivity as a result of enhanced capacitor was achieved for the detection and determination of random glucose concentration levels using a unique variation of capacitor that indeed results in an adequate variation of the resonance frequency. Moreover, the design and development of micro-resonator with enhanced MIS capacitor generate a resolution of 112.38 × 10 -3 pF/mg/dl, minimum detectable glucose level of 7.45mg/dl, and a limit of quantification of 22.58mg/dl. Additionally, this unique approach offers long-term reliability for mediator-free glucose sensing with a relative standard deviation of less than 0.5%. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Magnesium aminoclay enhances lipid production of mixotrophic Chlorella sp. KR-1 while reducing bacterial populations.

PubMed

Kim, Bohwa; Praveenkumar, Ramasamy; Lee, Jiye; Nam, Bora; Kim, Dong-Myung; Lee, Kyubock; Lee, Young-Chul; Oh, You-Kwan

2016-11-01

Improving lipid productivity and preventing overgrowth of contaminating bacteria are critical issues relevant to the commercialization of the mixotrophic microalgae cultivation process. In this paper, we report the use of magnesium aminoclay (MgAC) nanoparticles for enhanced lipid production from oleaginous Chlorella sp. KR-1 with simultaneous control of KR-1-associated bacterial growth in mixotrophic cultures with glucose as the model substrate. Addition of 0.01-0.1g/L MgAC promoted microalgal biomass production better than the MgAC-less control, via differential biocidal effects on microalgal and bacterial cells (the latter being more sensitive to MgAC's bio-toxicity than the former). The inhibition effect of MgAC on co-existing bacteria was, as based on density-gradient-gel-electrophoresis (DGGE) analysis, largely dosage-dependent and species-specific. MgAC also, by inducing an oxidative stress environment, increased both the cell size and lipid content of KR-1, resulting in a considerable, ∼25% improvement of mixotrophic algal lipid productivity (to ∼410mgFAME/L/d) compared with the untreated control. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cell Adhesion on Surface-Functionalized Magnesium.

PubMed

Wagener, Victoria; Schilling, Achim; Mainka, Astrid; Hennig, Diana; Gerum, Richard; Kelch, Marie-Luise; Keim, Simon; Fabry, Ben; Virtanen, Sannakaisa

2016-05-18

The biocompatibility of commercially pure magnesium-based (cp Mg) biodegradable implants is compromised of strong hydrogen evolution and surface alkalization due to high initial corrosion rates of cp Mg in the physiological environment. To mitigate this problem, the addition of corrosion-retarding alloying elements or coating of implant surfaces has been suggested. In the following work, we explored the effect of organic coatings on long-term cell growth. cp Mg was coated with aminopropyltriehtoxysilane + vitamin C (AV), carbonyldiimidazole (CDI), or stearic acid (SA). All three coatings have been previously suggested to reduce initial corrosion and to enhance protein adsorption and hence cell adhesion on magnesium surfaces. Endothelial cells (DH1+/+) and osteosarcoma cells (MG63) were cultured on coated samples for up to 20 days. To quantify Mg corrosion, electrochemical impedance spectroscopy (EIS) was measured after 1, 3, and 5 days of cell culture. We also investigated the speed of initial cell spreading after seeding using fluorescently labeled fibroblasts (NIH/3T3). Hydrogen evolution after contact with cell culture medium was markedly decreased on AV- and SA-coated Mg compared to uncoated Mg. These coatings also showed improved cell adhesion and spreading after 24 h of culture comparable to tissue-treated plastic surfaces. On AV-coated cp Mg, a confluent layer of endothelial cells formed after 5 days and remained intact for up to 20 days. Together, these data demonstrate that surface coating with AV is a viable strategy for improving long-term biocompatibility of cp Mg-based implants. EIS measurements confirmed that the presence of a confluent cell layer increased the corrosion resistance.

Reproducibility of Clathromorphum compactum coralline algal Mg/Ca ratios and comparison to high-resolution sea surface temperature data

NASA Astrophysics Data System (ADS)

Hetzinger, S.; Halfar, J.; Kronz, A.; Simon, K.; Adey, W. H.; Steneck, R. S.

2018-01-01

The potential of crustose coralline algae as high-resolution archives of past ocean variability in mid- to high-latitudes has only recently been recognized. Few comparisons of coralline algal proxies, such as temperature-dependent algal magnesium to calcium (Mg/Ca) ratios, with in situ-measured surface ocean data exist, even rarer are well replicated records from individual sites. We present Mg/Ca records from nine coralline algal specimens (Clathromorphum compactum) from a single site in the Gulf of Maine, North Atlantic. Sections from algal mounds were analyzed using Laser Ablation-Inductively Coupled Plasma Mass Spectrometry (LA-ICP-MS) yielding individual Mg/Ca records of up to 30 years in length. We first test intra- and intersample signal replication and show that algal Mg/Ca ratios are reproducible along several transects within individual sample specimens and between different samples from the same study site. In addition, LA-ICP-MS-derived Mg/Ca ratios are compared to electron microprobe (EMP) analyzed data on the longest-lived specimens and were found to be statistically commensurable. Second, we evaluate whether relationships between algal-based SST reconstructions and in situ temperature data can be improved by averaging Mg/Ca records from multiple algal specimens (intersample averages). We found that intersample averages yield stronger relationships to sea surface temperature (SST) data than Mg/Ca records derived from individual samples alone. Thus, Mg/Ca-based paleotemperature reconstructions from coralline algae can benefit from using multiple samples per site, and can expand temperature proxy precision from seasonal to monthly.

Recycling cellulase towards industrial application of enzyme treatment on hardwood kraft-based dissolving pulp.

PubMed

Wang, Qiang; Liu, Shanshan; Yang, Guihua; Chen, Jiachuan; Ji, Xingxiang; Ni, Yonghao

2016-07-01

Cost-effectiveness is vital for enzymatic treatment of dissolving pulp towards industrial application. The strategy of cellulase recycling with fresh cellulase addition was demonstrated in this work to activate the dissolving pulp, i.e. decreasing viscosity and increasing Fock reactivity. Results showed that 48.8-35.1% of cellulase activity can be recovered from the filtered liquor in five recycle rounds, which can be reused for enzymatic treatment of dissolving pulp. As a result, the recycling cellulase with addition fresh cellulase of 1mg/g led to the pulp of viscosity 470mL/g and Fock reactivity 80%, which is comparable with cellulase charge of 2mg/g. Other pulp properties such as alpha-cellulose, alkaline solubility and molecular weight distribution were also determined. Additionally, a zero-release of recycling cellulase treatment was proposed to integrate into the dissolving pulp production process. Copyright © 2016 Elsevier Ltd. All rights reserved.

Reduction in secondary dendrite arm spacing in cast eutectic Al-Si piston alloys by cerium addition

NASA Astrophysics Data System (ADS)

Ahmad, R.; Asmael, M. B. A.; Shahizan, N. R.; Gandouz, S.

2017-01-01

The effects of Ce on the secondary dendrite arm spacing (SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis (CA‒CCTA). The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, Δ t s, and low solidification temperature, Δ T S, whereas 0.1wt% Ce resulted in a fast solidification time, Δ t a-Al, of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index ( Q) and ultimate tensile strength of (UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.

Degradation of Phytate Pentamagnesium Salt by Bacillus sp. T4 Phytase as a Potential Eco-friendly Feed Additive

PubMed Central

Park, Inkyung; Lee, Jaekoo; Cho, Jaiesoon

2012-01-01

A bacterial isolate derived from soil samples near a cattle farm was found to display extracellular phytase activity. Based on 16S rRNA sequence analysis, the strain was named Bacillus sp. T4. The optimum temperature for the phytase activity toward magnesium phytate (Mg-InsP6) was 40°C without 5 mM Ca2+ and 50°C with 5 mM Ca2+. T4 phytase had a characteristic bi-hump two pH optima of 6.0 to 6.5 and 7.4 for Mg-InsP6. The enzyme showed higher specificity for Mg-InsP6 than sodium phytate (Na-InsP6). Its activity was fairly inhibited by EDTA, Cu2+, Mn2+, Co2+, Ba2+ and Zn2+. T4 phytase may have great potential for use as an eco-friendly feed additive to enhance the nutritive quality of phytate and reduce phosphorus pollution. PMID:25049504

Determination of 3-Monochloropropane-1,2-diol and 2-Monochloropropane-1,3-diol (MCPD) Esters and Glycidyl Esters by Microwave Extraction in Different Foodstuffs.

PubMed

Marc, Corinne; Drouard-Pascarel, Valérie; Rétho, Cécile; Janvion, Patrice; Saltron, Frédéric

2016-06-01

This paper describes a method for the determination of 3-monochloropropane-1,2-diol and 2-monochloropropane-1,3-diol (MCPD) esters and glycidyl esters in various foodstuffs, which are isolated using microwave extraction. The next step is based on alkaline-catalyzed ester cleavage. The released glycidol is transformed into monobromopropanediol (MBPD). All compounds are derivatized in free diols (MCPD and MBPD) with phenylboronic acid and analyzed by gas chromatography-mass spectrometry (GC-MS). The method was validated for oils with a limit of quantitation (LOQ) of 0.1 mg/kg, for chips and crisps with a LOQ of 0.02 mg/kg, and for infant formula with a LOQ of 0.0025 mg/L. Recoveries of each sample were controlled by standard addition on extracts before derivatization. Quantitation was performed by the addition of isotopically labeled glycidyl and 3-monochloropropane-1,2-diol (3-MCPD) esters.

A systematic study of 25Mg NMR in paramagnetic transition metal oxides: applications to Mg-ion battery materials.

PubMed

Lee, Jeongjae; Seymour, Ieuan D; Pell, Andrew J; Dutton, Siân E; Grey, Clare P

2016-12-21

Rechargeable battery systems based on Mg-ion chemistries are generating significant interest as potential alternatives to Li-ion batteries. Despite the wealth of local structural information that could potentially be gained from Nuclear Magnetic Resonance (NMR) experiments of Mg-ion battery materials, systematic 25 Mg solid-state NMR studies have been scarce due to the low natural abundance, low gyromagnetic ratio, and significant quadrupole moment of 25 Mg (I = 5/2). This work reports a combined experimental 25 Mg NMR and first principles density functional theory (DFT) study of paramagnetic Mg transition metal oxide systems Mg 6 MnO 8 and MgCr 2 O 4 that serve as model systems for Mg-ion battery cathode materials. Magnetic parameters, hyperfine shifts and quadrupolar parameters were calculated ab initio using hybrid DFT and compared to the experimental values obtained from NMR and magnetic measurements. We show that the rotor assisted population transfer (RAPT) pulse sequence can be used to enhance the signal-to-noise ratio in paramagnetic 25 Mg spectra without distortions in the spinning sideband manifold. In addition, the value of the predicted quadrupolar coupling constant of Mg 6 MnO 8 was confirmed using the RAPT pulse sequence. We further apply the same methodology to study the NMR spectra of spinel compounds MgV 2 O 4 and MgMn 2 O 4 , candidate cathode materials for Mg-ion batteries.

The Principal Hugoniot of Forsterite to 950 GPa

NASA Astrophysics Data System (ADS)

Root, Seth; Townsend, Joshua P.; Davies, Erik; Lemke, Raymond W.; Bliss, David E.; Fratanduono, Dayne E.; Kraus, Richard G.; Millot, Marius; Spaulding, Dylan K.; Shulenburger, Luke; Stewart, Sarah T.; Jacobsen, Stein B.

2018-05-01

Forsterite (Mg2SiO4) single crystals were shock compressed to pressures between 200 and 950 GPa using independent plate-impact steady shocks and laser-driven decaying shock compression experiments. Additionally, we performed density functional theory-based molecular dynamics to aid interpretation of the experimental data and to investigate possible phase transformations and phase separations along the Hugoniot. We show that the experimentally obtained Hugoniot cannot distinguish between a pure liquid Mg2SiO4 and an assemblage of solid MgO plus liquid magnesium silicate. The measured reflectivity is nonzero and increases with pressure, which implies that the liquid is a poor electrical conductor at low pressures and that the conductivity increases with pressure.

Effect of metal ions on the reactions of the cumyloxyl radical with hydrogen atom donors. Fine control on hydrogen abstraction reactivity determined by Lewis acid-base interactions.

PubMed

Salamone, Michela; Mangiacapra, Livia; DiLabio, Gino A; Bietti, Massimo

2013-01-09

A time-resolved kinetic study on the effect of metal ions (M(n+)) on hydrogen abstraction reactions from C-H donor substrates by the cumyloxyl radical (CumO(•)) was carried out in acetonitrile. Metal salt addition was observed to increase the CumO(•) β-scission rate constant in the order Li(+) > Mg(2+) > Na(+). These effects were explained in terms of the stabilization of the β-scission transition state determined by Lewis acid-base interactions between M(n+) and the radical. When hydrogen abstraction from 1,4-cyclohexadiene was studied in the presence of LiClO(4) and Mg(ClO(4))(2), a slight increase in rate constant (k(H)) was observed indicating that interaction between M(n+) and CumO(•) can also influence, although to a limited extent, the hydrogen abstraction reactivity of alkoxyl radicals. With Lewis basic C-H donors such as THF and tertiary amines, a decrease in k(H) with increasing Lewis acidity of M(n+) was observed (k(H)(MeCN) > k(H)(Li(+)) > k(H)(Mg(2+))). This behavior was explained in terms of the stronger Lewis acid-base interaction of M(n+) with the substrate as compared to the radical. This interaction reduces the degree of overlap between the α-C-H σ* orbital and a heteroatom lone-pair, increasing the C-H BDE and destabilizing the carbon centered radical formed after abstraction. With tertiary amines, a >2-order of magnitude decrease in k(H) was measured after Mg(ClO(4))(2) addition up to a 1.5:1 amine/Mg(ClO(4))(2) ratio. At higher amine concentrations, very similar k(H) values were measured with and without Mg(ClO(4))(2). These results clearly show that with strong Lewis basic substrates variations in the nature and concentration of M(n+) can dramatically influence k(H), allowing for a fine control of the substrate hydrogen atom donor ability, thus providing a convenient method for C-H deactivation. The implications and generality of these findings are discussed.

A combined toxicity study of zinc oxide nanoparticles and vitamin C in food additives.

PubMed

Wang, Yanli; Yuan, Lulu; Yao, Chenjie; Ding, Lin; Li, Chenchen; Fang, Jie; Sui, Keke; Liu, Yuanfang; Wu, Minghong

2014-12-21

At present, safety evaluation standards for nanofood additives are made based on the toxic effects of a single additive. Since the size, surface properties and chemical nature influence the toxicity of nanomaterials, the toxicity may have dramatically changed when nanomaterials are used as food additives in a complex system. Herein, we investigated the combined toxicity of zinc oxide nanoparticles (ZnO NPs) and vitamin C (Vc, ascorbic acid). The results showed that Vc increased the cytotoxicity significantly compared with that of the ZnO only NPs. When the cells were exposed to ZnO NPs at a concentration less than 15 mg L(-1), or to Vc at a concentration less than 300 mg L(-1), there was no significant cytotoxicity, both in the case of gastric epithelial cell line (GES-1) and neural stem cells (NSCs). However, when 15 mg L(-1) of ZnO NPs and 300 mg L(-1) of Vc were introduced to cells together, the cell viability decreased sharply indicating significant cytotoxicity. Moreover, the significant increase in toxicity was also shown in the in vivo experiments. The dose of the ZnO NPs and Vc used in the in vivo study was calculated according to the state of food and nutrition enhancer standard. After repeated oral exposure to ZnO NPs plus Vc, the injury of the liver and kidneys in mice has been indicated by the change of these indices. These findings demonstrate that the synergistic toxicity presented in a complex system is essential for the toxicological evaluation and safety assessment of nanofood.

Valomaciclovir versus valacyclovir for the treatment of acute herpes zoster in immunocompetent adults: a randomized, double-blind, active-controlled trial.

PubMed

Tyring, Stephen K; Plunkett, Stephanie; Scribner, Anita R; Broker, Robert E; Herrod, John N; Handke, Lane T; Wise, John M; Martin, Paul A

2012-08-01

Herpes zoster is a common infectious disease that can result in significant acute and chronic morbidity. The safety and efficacy of once-daily oral valomaciclovir (EPB-348) was evaluated for non-inferiority to 3-times daily valacyclovir, an approved therapy. In this study, 373 immunocompetent adults with onset of a herpes zoster rash within the preceding 72 hr were randomly assigned to receive one of four treatments for 7 days: (1) EPB-348 1,000 mg once-daily; (2) EPB-348 2,000 mg once-daily; (3) EPB-348 3,000 mg once-daily; or (4) valacyclovir 1,000 mg 3-times daily. A 20% margin was the reference for non-inferiority assessment. For the primary efficacy measure of time to complete crusting of the zoster rash by Day 28, non-inferiority criteria were met for once-daily EPB-348 2,000 mg and once-daily EPB-348 3,000 mg compared to 3-times daily valacyclovir. Additionally, EPB-348 3,000 mg significantly shortened the time to complete rash crusting by Day 28 compared to valacyclovir. For secondary efficacy measures, non-inferiority was achieved for the EPB-348 1,000 and 2,000 mg groups compared to the valacyclovir group for time to rash resolution by Day 28. No EPB-348 group was non-inferior to valacyclovir for time to cessation of new lesion formation or time to cessation of pain by Day 120, though no significant differences occurred between treatment groups. Nausea, headache, and vomiting were the most common adverse events. Based on these results, additional studies are warranted to define further EPB-348's potential as an effective and safe therapy for acute herpes zoster. Copyright © 2012 Wiley Periodicals, Inc.

VX-222, a non-nucleoside NS5B polymerase inhibitor, in telaprevir-based regimens for genotype 1 hepatitis C virus infection.

PubMed

Di Bisceglie, Adrian M; Sulkowski, Mark; Gane, Ed; Jacobson, Ira M; Nelson, David; DeSouza, Cynthia; Alves, Katia; George, Shelley; Kieffer, Tara; Zhang, Eileen Z; Kauffman, Robert; Asmal, Mohammed; Koziel, Margaret J

2014-07-01

To investigate in this phase 2a study (ZENITH) the safety, tolerability, and antiviral activity of VX-222, a selective, non-nucleoside inhibitor of hepatitis C virus (HCV) NS5B polymerase, combined with various telaprevir-based regimens for treatment of genotype 1 HCV. In total, 152 treatment-naive patients received VX-222+telaprevir ('DUAL' regimen; n=47), with ribavirin ('TRIPLE' regimen; n=46), or with peginterferon+ribavirin ('QUAD' regimen; n=59) for 12 weeks. Patients with detectable HCV RNA at weeks 2 and/or 8 received peginterferon+ribavirin for 24 (DUAL and TRIPLE) or 12 (QUAD) additional weeks. VX-222 (100 or 400 mg twice daily) was well tolerated, with an increased rate of gastrointestinal adverse events observed with the higher dose. Across VX-222 400-mg twice-daily regimens, the QUAD was associated with the highest frequency of grade 3/4 adverse events. The DUAL was discontinued because of high viral breakthrough before week 12. Sustained virologic response (SVR) 24 weeks after end of treatment (SVR24), including patients treated with 12 or 24 additional weeks of peginterferon+ribavirin, was 67% for TRIPLE (VX-222 400 mg twice daily) and 79 and 90% for QUAD (VX-222 100 and 400 mg twice daily, respectively). These results provide valuable information regarding the safety, tolerability, and efficacy of telaprevir combined with a non-nucleoside polymerase inhibitor, as dual therapy or with ribavirin without or with peginterferon. Telaprevir and VX-222, alone or with ribavirin without or with peginterferon, were generally well tolerated, with improved tolerability without peginterferon. SVR24 rates achieved with TRIPLE and QUAD regimens containing telaprevir and VX-222 were comparable to those observed with telaprevir-based therapy.

Magnesium Based Materials and their Antimicrobial Activity

NASA Astrophysics Data System (ADS)

Robinson, Duane Allan

The overall goals of this body of work were to characterize the antimicrobial properties of magnesium (Mg) metal and nano-magnesium oxide (nMgO) in vitro, to evaluate the in vitro cytotoxicity of Mg metal, and to incorporate MgO nanoparticles into a polymeric implant coating and evaluate its in vitro antimicrobial properties. In the course of this work it was found that Mg metal, Mg-mesh, and nMgO have in vitro antimicrobial properties that are similar to a bactericidal antibiotic. For Mg metal, the mechanism of this activity appears to be related to an increase in pH (i.e. a more alkaline environment) and not an increase in Mg2+. Given that Mg-mesh is a Mg metal powder, the assumption is that it has the same mechanism of activity as Mg metal. The mechanism of activity for nMgO remains to be elucidated and may be related to a combination of interaction of the nanoparticles with the bacteria and the alkaline pH. It was further demonstrated that supernatants from suspensions of Mg-mesh and nMgO had the same antimicrobial effect as was noted when the particles were used. The supernatant from Mg-mesh and nMgO was also noted to prevent biofilm formation for two Staphylococcus strains. Finally, poly-epsilon-caprolactone (PCL) composites of Mg-mesh (PCL+Mg-mesh) and nMgO (PCL+nMgO) were produced. Coatings applied to screws inhibited growth of Escherichia coli and Pseudomonas aeruginosa and in thin disc format inhibited the growth of Staphylococcus aureus in addition to the E. coli and P. aeruginosa. Pure Mg metal was noted to have some cytotoxic effect on murine fibroblast and osteoblast cell lines, although this effect needs to be characterized further. To address the need for an in vivo model for evaluating implant associated infections, a new closed fracture osteomyelitis model in the femur of the rat was developed. Magnesium, a readily available and inexpensive metal was shown to have antimicrobial properties that appear to be related to its corrosion products and that nMgO has similar effects. Incorporation of nMgO into a PCL composite was easily achieved and revealed similar, although not identical antimicrobial results. This work has provided a strong foundation and methodology for further evaluation of Mg based materials and their antimicrobial properties.

Influences on the H2-sorption properties of Mg of Co (with various sizes) and CoO addition by reactive grinding and their thermodynamic stabilities

NASA Astrophysics Data System (ADS)

Song, Myoung Youp; Lee, DongSub; Kwon, IkHyun

2004-02-01

We attempted to improve the H2-sorption properties of Mg by mechanical grinding under H2 (reactive grinding) with Co (with various particle sizes) and with CoO. The thermodynamic stabilities of the added Co and CoO were also investigated. CoO addition has the best influence and addition of smaller particles of Co (0.5-1.5 μm) has a better effect than the addition of larger particles of Co on the H2-sorption properties of Mg. The activated Mg+10 wt.% CoO sample has about 5.54 wt% hydrogen-storage capacity at 598 K and the highest hydriding rate, showing an Ha value of 2.39 wt.% after 60 min at 598 K, 11.2 bar H2. The order of the hydriding rates after activation is the same as that of the specific surface areas of the samples. The reactive grinding of Mg with Co or CoO and hydriding-dehydriding cycling increase the H2-sorption rates by facilitating nucleation of magnesium hydride or α solid solution of Mg and H (by creating defects on the surface of the Mg particles and by the additive), and by making cracks on the surface of Mg particles and reducing the particle size of Mg, thus shortening the diffusion distances of hydrogen atoms. The cobalt oxide is stable even after 14 hydriding cycles at 598 K under 11.2 bar H2. Discharge capacities are measured for the sampple Mg+10 wt.%CoO and Mg+10wt.%Co (0.5-1.5 μm) with good hydrogen-storage properties.

Biomedical coatings on magnesium alloys - a review.

PubMed

Hornberger, H; Virtanen, S; Boccaccini, A R

2012-07-01

This review comprehensively covers research carried out in the field of degradable coatings on Mg and Mg alloys for biomedical applications. Several coating methods are discussed, which can be divided, based on the specific processing techniques used, into conversion and deposition coatings. The literature review revealed that in most cases coatings increase the corrosion resistance of Mg and Mg alloys. The critical factors determining coating performance, such as corrosion rate, surface chemistry, adhesion and coating morphology, are identified and discussed. The analysis of the literature showed that many studies have focused on calcium phosphate coatings produced either using conversion or deposition methods which were developed for orthopaedic applications. However, the control of phases and the formation of cracks still appear unsatisfactory. More research and development is needed in the case of biodegradable organic based coatings to generate reproducible and relevant data. In addition to biocompatibility, the mechanical properties of the coatings are also relevant, and the development of appropriate methods to study the corrosion process in detail and in the long term remains an important area of research. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Ab initio study of single-crystalline and polycrystalline elastic properties of Mg-substituted calcite crystals.

PubMed

Zhu, L-F; Friák, M; Lymperakis, L; Titrian, H; Aydin, U; Janus, A M; Fabritius, H-O; Ziegler, A; Nikolov, S; Hemzalová, P; Raabe, D; Neugebauer, J

2013-04-01

We employ ab initio calculations and investigate the single-crystalline elastic properties of (Ca,Mg)CO3 crystals covering the whole range of concentrations from pure calcite CaCO3 to pure magnesite MgCO3. Studying different distributions of Ca and Mg atoms within 30-atom supercells, our theoretical results show that the energetically most favorable configurations are characterized by elastic constants that nearly monotonously increase with the Mg content. Based on the first principles-derived single-crystalline elastic anisotropy, the integral elastic response of (Ca,Mg)CO3 polycrystals is determined employing a mean-field self-consistent homogenization method. As in case of single-crystalline elastic properties, the computed polycrystalline elastic parameters sensitively depend on the chemical composition and show a significant stiffening impact of Mg atoms on calcite crystals in agreement with the experimental findings. Our analysis also shows that it is not advantageous to use a higher-scale two-phase mix of stoichiometric calcite and magnesite instead of substituting Ca atoms by Mg ones on the atomic scale. Such two-phase composites are not significantly thermodynamically favorable and do not provide any strong additional stiffening effect. Copyright © 2013 Elsevier Ltd. All rights reserved.

Characterization of the nociceptin receptor (ORL-1) agonist, Ro64-6198, in tests of anxiety across multiple species.

PubMed

Varty, G B; Hyde, L A; Hodgson, R A; Lu, S X; McCool, M F; Kazdoba, T M; Del Vecchio, R A; Guthrie, D H; Pond, A J; Grzelak, M E; Xu, X; Korfmacher, W A; Tulshian, D; Parker, E M; Higgins, G A

2005-10-01

Previous studies have demonstrated behaviors indicative of anxiolysis in rats pretreated with the nociceptin receptor (opioid receptor like-1, ORL-1) agonist, Ro64-6198. The aim of this study was to examine the effects of Ro64-6198 in anxiety models across three species: rat, guinea pig, and mouse. In addition, the receptor specificity of Ro64-6198 was studied, using the ORL-1 receptor antagonist, J-113397, and ORL-1 receptor knockout (KO) mice. Finally, neurological studies examined potential side effects of Ro64-6198 in the rat and mouse. Ro64-6198 (3-10 mg/kg) increased punished responding in a rat conditioned lick suppression test similarly to chlordiazepoxide (6 mg/kg). This effect of Ro64-6198 was attenuated by J-113397 (10 mg/kg), but not the mu opioid antagonist, naltrexone (3 mg/kg). In addition, Ro64-6198 (1-3 mg/kg) reduced isolation-induced vocalizations in rat and guinea pig pups. Ro64-6198 (3 mg/kg) increased the proportion of punished responding in a mouse Geller-Seifter test in wild-type (WT) but not ORL-1 KO mice, whereas diazepam (1-5.6 mg/kg) was effective in both genotypes. In rats, Ro64-6198 reduced locomotor activity (LMA) and body temperature and impaired rotarod, beam walking, and fixed-ratio (FR) performance at doses of 10-30 mg/kg, i.e., three to ten times higher than an anxiolytic dose. In WT mice, Ro64-6198 (3-10 mg/kg) reduced LMA and rotarod performance, body temperature, and FR responding, but these same measures were unaffected in ORL-1 KO mice. Haloperidol (0.3-3 mg/kg) reduced these measures to a similar extent in both genotypes. These studies confirm the potent, ORL-1 receptor-mediated, anxiolytic-like effects of Ro64-6198, extending the findings across three species. Ro64-6198 has target-based side effects, although the magnitude of these effects varies across species.

Enhancing the Ignition, Hardness and Compressive Response of Magnesium by Reinforcing with Hollow Glass Microballoons

PubMed Central

Gupta, Manoj

2017-01-01

Magnesium (Mg)/glass microballoons (GMB) metal matrix syntactic foams (1.47–1.67 g/cc) were synthesized using a disintegrated melt deposition (DMD) processing route. Such syntactic foams are of great interest to the scientific community as potential candidate materials for the ever-changing demands in automotive, aerospace, and marine sectors. The synthesized composites were evaluated for their microstructural, thermal, and compressive properties. Results showed that microhardness and the dimensional stability of pure Mg increased with increasing GMB content. The ignition response of these foams was enhanced by ~22 °C with a 25 wt % GMB addition to the Mg matrix. The authors of this work propose a new parameter, ignition factor, to quantify the superior ignition performance that the developed Mg foams exhibit. The room temperature compressive strengths of pure Mg increased with the addition of GMB particles, with Mg-25 wt % GMB exhibiting the maximum compressive yield strength (CYS) of 161 MPa and an ultimate compressive strength (UCS) of 232 MPa for a GMB addition of 5 wt % in Mg. A maximum failure strain of 37.7% was realized in Mg-25 wt % GMB foam. The addition of GMB particles significantly enhanced the energy absorption by ~200% prior to compressive failure for highest filler loading, as compared to pure Mg. Finally, microstructural changes in Mg owing to the presence of hollow GMB particles were elaborately discussed. PMID:28841189

Magnesium Fertilizer-Induced Increase of Symbiotic Microorganisms Improves Forage Growth and Quality.

PubMed

Chen, Jihui; Li, Yanpeng; Wen, Shilin; Rosanoff, Andrea; Yang, Gaowen; Sun, Xiao

2017-04-26

Magnesium (Mg) plays important roles in photosynthesis and protein synthesis; however, latent Mg deficiencies are common phenomena that can influence food quality. Nevertheless, the effects of Mg fertilizer additions on plant carbon (C):nitrogen (N):phosphorus (P) stoichiometry, an important index of food quality, are unclear and the underlying mechanisms unexplored. We conducted a greenhouse experiment using low-Mg in situ soil without and with a gradient of Mg additions to investigate the effect of Mg fertilizer on growth and stoichiometry of maize and soybean and also measure these plants' main symbiotic microorganisms: arbuscular mycorrhizal fungi (AMF) and rhizobium, respectively. Our results showed that Mg addition significantly improved both plant species' growth and also increased N and P concentrations in soybean and maize, respectively, resulting in low C:N ratio and high N:P ratio in soybean and low C:P and N:P ratios in maize. These results presumably stemmed from the increase of nutrients supplied by activation-enhanced plant symbiotic microorganisms, an explanation supported by statistically significant positive correlations between plant stoichiometry and plants' symbiotic microorganisms' increased growth with Mg addition. We conclude that Mg supply can improve plant growth and alter plant stoichiometry via enhanced activity of plant symbiotic microorganisms. Possible mechanisms underlying this positive plant-soil feedback include an enhanced photosynthetic product flow to roots caused by adequate Mg supply.

Enhancing the Ignition, Hardness and Compressive Response of Magnesium by Reinforcing with Hollow Glass Microballoons.

PubMed

Manakari, Vyasaraj; Parande, Gururaj; Doddamani, Mrityunjay; Gupta, Manoj

2017-08-25

Magnesium (Mg)/glass microballoons (GMB) metal matrix syntactic foams (1.47-1.67 g/cc) were synthesized using a disintegrated melt deposition (DMD) processing route. Such syntactic foams are of great interest to the scientific community as potential candidate materials for the ever-changing demands in automotive, aerospace, and marine sectors. The synthesized composites were evaluated for their microstructural, thermal, and compressive properties. Results showed that microhardness and the dimensional stability of pure Mg increased with increasing GMB content. The ignition response of these foams was enhanced by ~22 °C with a 25 wt % GMB addition to the Mg matrix. The authors of this work propose a new parameter, ignition factor, to quantify the superior ignition performance that the developed Mg foams exhibit. The room temperature compressive strengths of pure Mg increased with the addition of GMB particles, with Mg-25 wt % GMB exhibiting the maximum compressive yield strength (CYS) of 161 MPa and an ultimate compressive strength (UCS) of 232 MPa for a GMB addition of 5 wt % in Mg. A maximum failure strain of 37.7% was realized in Mg-25 wt % GMB foam. The addition of GMB particles significantly enhanced the energy absorption by ~200% prior to compressive failure for highest filler loading, as compared to pure Mg. Finally, microstructural changes in Mg owing to the presence of hollow GMB particles were elaborately discussed.

Formation of chemically bonded ceramics with magnesium dihydrogen phosphate binder

DOEpatents

Wagh, Arun S.; Jeong, Seung-Young

2004-08-17

A new method for combining magnesium oxide, MgO, and magnesium dihydrogen phosphate to form an inexpensive compactible ceramic to stabilize very low solubility metal oxides, ashes, swarfs, and other iron or metal-based additives, to create products and waste forms which can be poured or dye cast, and to reinforce and strengthen the ceramics formed by the addition of fibers to the initial ceramic mixture.

ZnO-based ultraviolet photodetectors.

PubMed

Liu, Kewei; Sakurai, Makoto; Aono, Masakazu

2010-01-01

Ultraviolet (UV) photodetection has drawn a great deal of attention in recent years due to a wide range of civil and military applications. Because of its wide band gap, low cost, strong radiation hardness and high chemical stability, ZnO are regarded as one of the most promising candidates for UV photodetectors. Additionally, doping in ZnO with Mg elements can adjust the bandgap largely and make it feasible to prepare UV photodetectors with different cut-off wavelengths. ZnO-based photoconductors, Schottky photodiodes, metal-semiconductor-metal photodiodes and p-n junction photodetectors have been developed. In this work, it mainly focuses on the ZnO and ZnMgO films photodetectors. We analyze the performance of ZnO-based photodetectors, discussing recent achievements, and comparing the characteristics of the various photodetector structures developed to date.

Lurasidone for schizophrenia: a review of the efficacy and safety profile for this newly approved second-generation antipsychotic.

PubMed

Citrome, L

2011-02-01

To describe the efficacy and safety of lurasidone for the treatment of schizophrenia. The pivotal registration trials were accessed by querying the literature databases PubMed, EMBASE, ISI Web of Knowledge, as well as http://www.fda.gov and http://www.clinicaltrials.gov for the search term 'lurasidone'. Product labelling provided additional information. All available clinical reports of studies were identified. Descriptions of the principal results and calculation of number needed to treat (NNT) and number needed to harm (NNH) for relevant dichotomous outcomes were extracted from the available study reports, abstracts and posters. Additional safety outcomes subject to NNH analysis were obtained from product labelling. Lurasidone is a second-generation antipsychotic approved for the treatment of schizophrenia at a recommended starting dose of 40 mg/day administered once daily with food (≥350 calories). The maximum recommended dose is 80 mg/day. Regulatory approval was based primarily on a clinical trial programme that included four 6-week randomised clinical trials demonstrating efficacy vs. placebo in acute patients with schizophrenia. One additional Phase II clinical trial was considered a failed study because neither lurasidone nor the active control, haloperidol, separated from placebo on the primary outcome measure. One additional Phase III study was completed after the new drug application was submitted to the US Food and Drug Administration. Efficacy outcomes appear consistently in favour of lurasidone 80 mg/day vs. placebo on multiple measures of psychopathology, however, at least two studies also demonstrated efficacy for the doses of 40 and 120 mg/day. NNT vs. placebo was 3-6 for response as defined by ≥20% reduction in psychopathological rating scale total scores from baseline, depending on the study and the dose. Response as defined by a ≥30% improvement yielded NNTs ranging from 7 to 13. The most common adverse events in the clinical trials were somnolence (broadly defined), akathisia, nausea, parkinsonism and agitation. As estimated from product labelling, NNH vs. placebo was dose dependent for somnolence, with a NNH of 6 for lurasidone 120 mg/day, compared with NNHs of 8, 11 and 20, for 80, 40 and 20 mg/day, respectively. For akathisia NNH was 6 for lurasidone 120 mg/day, compared to NNHs of 9, 13 and 34 for 80, 40 and 20 mg/day, respectively. Lurasidone is associated with minimal weight gain and no clinically meaningful alterations in glucose, lipids, prolactin or the ECG QT interval. Lurasidone 40 and 80 mg/day appear efficacious and tolerable in the treatment of schizophrenia. Doses above 80 mg/day do not appear to confer added benefit and may be associated with a dose-related increase in certain adverse reactions. Principal advantages over some other second-generation antipsychotics are lurasidone's highly favourable metabolic profile and once-daily dosing regimen. Additional data regarding long-term efficacy and effectiveness will help characterise this new agent when used in maintenance treatment. © 2010 Blackwell Publishing Ltd.

Reinforcing aluminum alloys with high strength fibers

NASA Technical Reports Server (NTRS)

Kolpashnikov, A. I.; Manuylov, V. F.; Chukhin, B. D.; Shiryayev, Y. V.; Shurygin, A. S.

1982-01-01

A study is made of the possibility of reinforcing aluminum and aluminum based alloys with fibers made of high strength steel wire. The method of introducing the fibers is described in detail. Additional strengthening by reinforcement of the high alloy system Al - An - Mg was investigated.

Application of rhamnolipid and surfactin for enhanced diesel biodegradation--effects of pH and ammonium addition.

PubMed

Whang, Liang-Ming; Liu, Pao-Wen G; Ma, Chih-Chung; Cheng, Sheng-Shung

2009-05-30

This study investigated the effects of pH and ammonium concentrations on the potential application of two biosurfactants, surfactin (SF) and rhamnolipid (RL), for enhanced diesel biodegradation with a series of bench-scale experiments. In general, compared to the experiments without biosurfactant addition, adding RL or SF to diesel-water systems at concentrations above their critical micelle concentration (CMC) values benefited diesel emulsification, and therefore enhanced diesel biodegradation. The effects of pH on RL or SF-enhanced biodegradation of diesel were in good agreement with the trends of emulsion index values for RL or SF addition, respectively, under different pH conditions, suggesting that enhanced diesel emulsification by RL or SF addition promoted biodegradation of diesel. In diesel-water systems with 50mg/L of RL addition, an optimum pH condition for microbial growth and diesel biodegradation was found to be at a pH 7.2, while decreasing pH to 5.2 or increasing it to 8.4 reduced those parameters considerably. For the cases where 40 mg/L of SF was added, the enhancing ability shared a general trend with that observed for adding 50mg/L of RL as the pH increased from 5.2 to 7.2. Further increase of pH to 8.4, however, did not seem to negatively influence biodegradation and biomass growth. With respect to the effects of ammonium concentration on diesel biodegradation in diesel-water systems with 50mg/L of RL addition, an optimum ammonium addition for microbial growth and diesel biodegradation was found between 200 and 300 mg-N/L, but a dramatic decrease in growth and biodegradation occurred at ammonium addition up to 450 mg-N/L. For the cases where 40 mg/L of SF was added, an increase of ammonium addition from 50 to 200mg-N/L substantially increased microbial growth and biodegradation of diesel. Further increase of ammonium concentration to 450 mg-N/L, however, did not further improve diesel biodegradation.

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- xSn Alloys

NASA Astrophysics Data System (ADS)

Wang, Feng; Dong, Haikuo; Sun, Shijie; Wang, Zhi; Mao, Pingli; Liu, Zheng

2018-02-01

The microstructure, tensile properties, and corrosion behavior of die-cast Mg-7Al-1Ca- xSn ( x = 0, 0.5, 1.0, and 2.0 wt.%) alloys were studied using OM, SEM/EDS, tensile test, weight loss test, and electrochemical test. The experimental results showed that Sn addition effectively refined grains and intermetallic phases and increased the amount of intermetallic phases. Meanwhile, Sn addition to the alloys suppressed the formation of the (Mg,Al)2Ca phase and resulted in the formation of the ternary CaMgSn phase and the binary Mg2Sn phase. The Mg-7Al-1Ca-0.5Sn alloy exhibited best tensile properties at room temperature, while Mg-7Al-1Ca-1.0Sn alloy exhibited best tensile properties at elevated temperature. The corrosion resistance of studied alloys was improved by the Sn addition, and the Mg-7Al-1Ca-0.5Sn alloy presented the best corrosion resistance.

A Dosing Study of Bevacizumab for Retinopathy of Prematurity: Late Recurrences and Additional Treatments.

PubMed

Wallace, David K; Dean, Trevano W; Hartnett, Mary Elizabeth; Kong, Lingkun; Smith, Lois E; Hubbard, G Baker; McGregor, Mary Lou; Jordan, Catherine O; Mantagos, Iason S; Bell, Edward F; Kraker, Raymond T

2018-06-07

Intravitreal bevacizumab is increasingly used to treat severe retinopathy of prematurity (ROP), but it enters the bloodstream, and there is concern that it may alter development of other organs. Previously we reported short-term outcomes of 61 infants enrolled in a dose de-escalation study, and we report the late recurrences and additional treatments. Masked, multicenter, dose de-escalation study. A total of 61 premature infants with type 1 ROP. If type 1 ROP was bilateral at enrollment, then the study eye was randomly selected. In the study eye, bevacizumab intravitreal injections were given at de-escalating doses of 0.25 mg, 0.125 mg, 0.063 mg, or 0.031 mg; if needed, fellow eyes received 1 dose level higher: 0.625 mg, 0.25 mg, 0.125 mg, or 0.063 mg, respectively. After 4 weeks, additional treatment was at the discretion of the investigator. Early and late ROP recurrences, additional treatments, and structural outcomes after 6 months. Of 61 study eyes, 25 (41%; 95% confidence interval [CI], 29%-54%) received additional treatment: 3 (5%; 95% CI, 1%-14%) for early failure (within 4 weeks), 11 (18%; 95% CI, 9%-30%) for late recurrence of ROP (after 4 weeks), and 11 (18%; 95% CI, 9%-30%) for persistent avascular retina. Re-treatment for early failure or late recurrence occurred in 2 of 11 eyes (18%; 95% CI, 2%-52%) treated with 0.25 mg, 4 of 16 eyes (25%; 95% CI, 7%-52%) treated with 0.125 mg, 8 of 24 eyes (33%; 95% CI, 16%-55%) treated with 0.063 mg, and 0 (0%; 95% CI, 0%-31%) of 10 eyes treated with 0.031 mg. By 6 months corrected age, 56 of 61 study eyes had regression of ROP with normal posterior poles, 1 study eye had developed a Stage 5 retinal detachment, and 4 infants had died of preexisting medical conditions. Retinal structural outcomes are very good after low-dose bevacizumab treatment for ROP, although many eyes received additional treatment. Copyright © 2018 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Synthesis and characterization of SiC based composite materials for immobilizing radioactive graphite

NASA Astrophysics Data System (ADS)

Wang, Qing; Teng, Yuancheng; Wu, Lang; Zhang, Kuibao; Zhao, Xiaofeng; Hu, Zhuang

2018-06-01

In order to immobilize high-level radioactive graphite, silicon carbide based composite materials{ (1-x) SiC· x MgAl2O4 (0.1 ≤ x≤0.4) } were fabricated by solid-state reaction at 1370 °C for 2 h in vacuum. Residual graphite and precipitated corundum were observed in the as-synthesized product, which attributed to the interface reaction of element silicon and magnesium compounds. To further understand the reasons for the presence of graphite and corundum, the effects of mole ratio of Si/C, MgAl2O4 content and non-stoichiometry of MgAl2O4 on the synthesis were investigated. To immobilize graphite better, residual graphite should be eliminated. The target product was obtained when the mole ratio of Si/C was 1.3:1, MgAl2O4 content was x = 0.2, and the mole ratio of Al to Mg in non-stoichiometric MgAl2O4 was 1.7:1. In addition, the interface reaction between magnesium compounds and silicon not graphite was displayed by conducting a series of comparative experiments. The key factor for the occurrence of interface reaction is that oxygen atom is transferred from magnesium compound to SiO gas. Infrared and Raman spectrum revealed the increased disorders of graphite after being synthesized.

Effect of magnesium ions on the structure of DNA thin films: an infrared spectroscopy study

PubMed Central

Serec, Kristina; Babić, Sanja Dolanski; Podgornik, Rudolf; Tomić, Silvia

2016-01-01

Utilizing Fourier transform infrared spectroscopy we have investigated the vibrational spectrum of thin dsDNA films in order to track the structural changes upon addition of magnesium ions. In the range of low magnesium concentration ([magnesium]/[phosphate] = [Mg]/[P] < 0.5), both the red shift and the intensity of asymmetric PO2 stretching band decrease, indicating an increase of magnesium-phosphate binding in the backbone region. Vibration characteristics of the A conformation of the dsDNA vanish, whereas those characterizing the B conformation become fully stabilized. In the crossover range with comparable Mg and intrinsic Na DNA ions ([Mg]/[P] ≈ 1) B conformation remains stable; vibrational spectra show moderate intensity changes and a prominent blue shift, indicating a reinforcement of the bonds and binding in both the phosphate and the base regions. The obtained results reflect the modified screening and local charge neutralization of the dsDNA backbone charge, thus consistently demonstrating that the added Mg ions interact with DNA via long-range electrostatic forces. At high Mg contents ([Mg]/[P] > 10), the vibrational spectra broaden and show a striking intensity rise, while the base stacking remains unaffected. We argue that at these extreme conditions, where a charge compensation by vicinal counterions reaches 92–94%, DNA may undergo a structural transition into a more compact form. PMID:27484473

SOLID SOLUTION EFFECTS ON THE THERMAL PROPERTIES IN THE MgAl2O4-MgGa2O4

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Hara, Kelley; Smith, Jeffrey D; Sander, Todd P.

Solid solution eects on thermal conductivity within the MgO-Al2O3-Ga2O3 system were studied. Samples with systematically varied additions of MgGa2O4 to MgAl2O4 were prepared and the laser ash technique was used to determine thermal diusivity at temperatures between 200C and 1300C. Heat capacity as a function of temperature from room temperature to 800C was also determined using dierential scanning calorimetry. Solid solution in the MgAl2O4-MgGa2O4 system decreases the thermal conductivity up to 1000C. At 200C thermal conductivity decreased 24% with a 5 mol% addition of MgGa2O4 to the system. At 1000C the thermal conductivity decreased 13% with a 5 mol% addition.more » Steady state calculations showed a 12.5% decrease in heat ux with 5 mol% MgGa2O4 considered across a 12 inch thickness.« less

Structural and optical properties of MgxAl1-xHy gradient thin films: a combinatorial approach

NASA Astrophysics Data System (ADS)

Gremaud, R.; Borgschulte, A.; Chacon, C.; van Mechelen, J. L. M.; Schreuders, H.; Züttel, A.; Hjörvarsson, B.; Dam, B.; Griessen, R.

2006-07-01

The structural, optical and dc electrical properties of MgxAl1-x (0.2≤x≤0.9) gradient thin films covered with Pd/Mg are investigated before and after exposure to hydrogen. We use hydrogenography, a novel high-throughput optical technique, to map simultaneously all the hydride forming compositions and the kinetics thereof in the gradient thin film. Metallic Mg in the MgxAl1-x layer undergoes a metal-to-semiconductor transition and MgH2 is formed for all Mg fractions x investigated. The presence of an amorphous Mg-Al phase in the thin film phase diagram enhances strongly the kinetics of hydrogenation. In the Al-rich part of the film, a complex H-induced segregation of MgH2 and Al occurs. This uncommon large-scale segregation is evidenced by metal and hydrogen profiling using Rutherford backscattering spectrometry and resonant nuclear analysis based on the reaction 1H(15N,αγ)12C. Besides MgH2, an additional semiconducting phase is found by electrical conductivity measurements around an atomic [Al]/[Mg] ratio of 2 (x=0.33). This suggests that the film is partially transformed into Mg(AlH4)2 at around this composition.

Influence of in situ and ex situ ZrO2 addition on the properties of MgB2

NASA Astrophysics Data System (ADS)

Chen, S. K.; Glowacki, B. A.; MacManus-Driscoll, J. L.; Vickers, M. E.; Majoros, M.

2004-02-01

The effect of ZrO2 addition on the properties of MgB2 has been studied using in situ and ex situ processes. The in situ process was performed by introducing ZrO2 from the milling tools into MgB2 throughout the planetary ball milling, whereas the ex situ process was accomplished by mixing ZrO2 from the milling tools with MgB2 by hand grinding in a mortar. A detectable amount of ZrO2 was present in MgB2 after 4 h of milling during the in situ process and its content increased with milling time as expected. The 400 h milled powder was partially amorphized and showed the formation of a minority ZrB2 phase. For milling up to 100 h, diamagnetism of MgB2 was significantly reduced while Tc remained unchanged. Superconductivity was totally destroyed after 148 h of milling. The loss of superconductivity is attributed to the effect of disordering induced by mechanical milling. As a result of in situ ZrO2 addition, the initial Tc and crystal structure of MgB2 could not be restored upon annealing. With increasing milling time, the expansion of lattice parameters in both the a-axis and c-axis may be due to possible substitution of Mg or B by Zr. The result from the magnetic measurement shows that Jc of MgB2 is deteriorated by in situ ZrO2 addition. On the other hand, ex situ ZrO2 addition with annealing did not degrade the Tc of MgB2.

Precipitation of ammonium from concentrated industrial wastes as struvite: a search for the optimal reagents.

PubMed

Borojovich, Eitan J C; Münster, Meshulam; Rafailov, Gennady; Porat, Ze'ev

2010-07-01

Precipitation of struvite (MgNH4PO4) is a known process for purification of wastewater from high concentrations of ammonium. The optimal conditions for precipitation are basic pH (around 9) and sufficient concentrations of magnesium and phosphate ions. In this work, we accomplished efficient precipitation of ammonium from concentrated industrial waste stream by using magnesium oxide (MgO) both as a source of magnesium ions and as a base. Best results were obtained with technical-grade MgO, which provided 99% removal of ammonium. Moreover, ammonium removal occurred already at pH 7, and the residual ammonium concentration (50 mg/L) remained constant upon addition of more MgO without rising again, as occurs with sodium hydroxide (NaOH). This process may have two other advantages; it also can be relevant for the problem of uncontrolled precipitation of struvite in the supernatant of anaerobic sludge treatment plants, and the precipitate can be used as a fertilizer.

High hydrogen desorption properties of Mg-based nanocomposite at moderate temperatures: The effects of multiple catalysts in situ formed by adding nickel sulfides/graphene

NASA Astrophysics Data System (ADS)

Xie, Xiubo; Chen, Ming; Liu, Peng; Shang, Jiaxiang; Liu, Tong

2017-12-01

Nickel sulfides decorated reduced graphene oxide (rGO) has been produced by co-reducing Ni2+ and graphene oxide (GO), and is subsequently ball milled with Mg nanoparticles (NPs) produced by hydrogen plasma metal reaction (HPMR). The nickel sulfides of about 800 nm completely in situ change to MgS, Mg2Ni and Ni multiple catalysts after first hydrogenation/dehydrogenation process at 673 K. The Mg-5wt%NiS/rGO nanocomposite shows the highest hydrogen desorption kinetics and capacity properties, and the catalytic effect order of the additives is NiS/rGO, NiS and rGO. At 573 K, the Mg-NiS/rGO nanocomposite can quickly desorb 3.7 wt% H2 in 10 min and 4.5 wt% H2 in 60 min. The apparent hydrogen absorption and desorption activation energies of the Mg-5wt%NiS/rGO nanocomposite are decreased to 44.47 and 63.02 kJ mol-1, smaller than those of the Mg-5wt%rGO and Mg-5wt%NiS samples. The best hydrogen desorption properties of the Mg-5wt%NiS/rGO nanocomposite can be explained by the synergistic catalytic effects of the highly dispersed MgS, Mg2Ni and Ni catalysts on the rGO sheets, and the more nucleation sites between the catalysts, rGO sheets and Mg matrix.

DIFFUSION OF MAGNESIUM AND MICROSTRUCTURES IN Mg+ IMPLANTED SILICON CARBIDE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Weilin; Edwards, Danny J.; Jung, Hee Joon

2014-08-28

Following our previous reports [ 1- 3], further isochronal annealing (2 hrs.) of the monocrystalline 6H-SiC and polycrystalline CVD 3C-SiC was performed at 1573 and 1673 K in Ar environment. SIMS data indicate that observable Mg diffusion in 6H-SiC starts and a more rapid diffusion in CVD 3C-SiC occurs at 1573 K. The implanted Mg atoms tend to diffuse deeper into the undamaged CVD 3C-SiC. The microstructure with Mg inclusions in the as-implanted SiC has been initially examined using high-resolution STEM. The presence of Mg in the TEM specimen has been confirmed based on EDS mapping. Additional monocrystalline 3C-SiC samplesmore » have been implanted at 673 K to ion fluence 3 times higher than the previous one. RBS/C analysis has been performed before and after thermal annealing at 1573 K for 12 hrs. Isothermal annealing at 1573 K is being carried out and Mg depth profiles being measured. Microstructures in both the as-implanted and annealed samples are also being examined using STEM.« less

Stem-Loop V of Varkud Satellite RNA Exhibits Characteristics of the Mg2+ Bound Structure in the Presence of Monovalent Ions

PubMed Central

2015-01-01

The Varkud Satellite RNA contains a self-cleaving ribozyme that has been shown to function independently of its surroundings. This 160 nucleotide ribozyme adopts a catalytically active tertiary structure that includes a kissing hairpin complex formed by stem-loop I and stem-loop V (SLV). The five-nucleotide 5′-rUGACU loop of the isolated SLV has been shown to adopt a Mg2+-dependent U-turn structure by solution NMR. This U-turn hairpin is examined here by molecular dynamics simulations in the presence of monovalent and divalent ions. Simulations confirm on an all-atom level the hypotheses for the role of the Mg2+ ions in stabilizing the loop, as well as the role of the solvent exposed U700 base. Additionally, these simulations suggest the Mg2+-free stem-loop adopts a wide range of structures, including energetically favorable structures similar to the Mg2+-bound loop structure. We propose this structure is a “gatekeeper” or precursor to Mg2+ binding when those ions are present. PMID:26328924

A multi-mode operation control strategy for flexible microgrid based on sliding-mode direct voltage and hierarchical controls.

PubMed

Zhang, Qinjin; Liu, Yancheng; Zhao, Youtao; Wang, Ning

2016-03-01

Multi-mode operation and transient stability are two problems that significantly affect flexible microgrid (MG). This paper proposes a multi-mode operation control strategy for flexible MG based on a three-layer hierarchical structure. The proposed structure is composed of autonomous, cooperative, and scheduling controllers. Autonomous controller is utilized to control the performance of the single micro-source inverter. An adaptive sliding-mode direct voltage loop and an improved droop power loop based on virtual negative impedance are presented respectively to enhance the system disturbance-rejection performance and the power sharing accuracy. Cooperative controller, which is composed of secondary voltage/frequency control and phase synchronization control, is designed to eliminate the voltage/frequency deviations produced by the autonomous controller and prepare for grid connection. Scheduling controller manages the power flow between the MG and the grid. The MG with the improved hierarchical control scheme can achieve seamless transitions from islanded to grid-connected mode and have a good transient performance. In addition the presented work can also optimize the power quality issues and improve the load power sharing accuracy between parallel VSIs. Finally, the transient performance and effectiveness of the proposed control scheme are evaluated by theoretical analysis and simulation results. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Ca Addition Effects on the Microstructure, Tensile and Corrosion Properties of Mg Matrix Alloy Containing 8 wt.% Mg2Si

NASA Astrophysics Data System (ADS)

Lotfpour, M.; Emamy, M.; Dehghanian, C.; Pourbahari, B.

2018-02-01

The microstructure, tensile properties and corrosion behavior of the Mg-8 wt.% Mg2Si-x%Ca alloy have been studied by the use of optical microscopy, scanning electron microscopy equipped with energy-dispersive spectroscopy, x-ray diffraction, standard tensile testing, polarization test and electrochemical impedance spectroscopy (EIS) measurements. Microstructural studies indicated that Ca modifies both primary and eutectic Mg2Si phase. It was found that the average size of primary Mg2Si particles is about 60 μm, which is dropped by about 82% in the alloy containing 0.05 wt.% Ca. By the addition of different Ca contents, Ca-rich intermetallics (i.e., CaSi2 and CaMgSi) were formed. The modification mechanism of adding Ca during solidification was found to be due to the strong effect of CaMgSi phase as a heterogonous nucleation site, apart from CaSi2 which was reported before, for Mg2Si intermetallics. Tensile testing results ascertained that Ca addition enhances both ultimate tensile strength (UTS) and elongation values. The optimum amount of Ca was found to be 0.1 wt.%, which improved UTS and elongation values from about 130 MPa and 2% to 165 MPa and 5.5%, whereas more Ca addition (i.e., 3 wt.%) reduced the tensile properties of the alloy to about 105 MPa and 1.8%, which can be due to the formation of CaMgSi intermetallics with deteriorating needle-like morphology. Polarization and EIS tests also showed that the Mg-3%Si-0.5%Ca alloy pronounces as the best anti-corrosion alloy. Nevertheless, further added Ca (up to 3 wt.%) deteriorated the corrosion resistance due to predominance of worse galvanic coupling effect stemmed from the presence of stronger CaMgSi cathode in comparison with Mg2Si. With higher Ca additions, an adverse effect was seen on corrosion resistance of the Mg-3%Si alloy, as a result of forming a weak film on the alloy specimen surface.

The Principal Hugoniot of Forsterite to 950 GPa

DOE PAGES

Root, Seth; Townsend, Joshua P.; Davies, Erik; ...

2018-04-27

Forsterite (Mg 2SiO 4) single crystals were shock compressed to pressures between 200 and 950 GPa using independent plate–impact steady shocks and laser–driven decaying shock compression experiments. Additionally, we performed density functional theory–based molecular dynamics to aid interpretation of the experimental data and to investigate possible phase transformations and phase separations along the Hugoniot. We show that the experimentally obtained Hugoniot cannot distinguish between a pure liquid Mg 2SiO 4 and an assemblage of solid MgO plus liquid magnesium silicate. In conclusion, the measured reflectivity is nonzero and increases with pressure, which implies that the liquid is a poor electricalmore » conductor at low pressures and that the conductivity increases with pressure.« less

Tafenoquine for the treatment of recurrent Plasmodium vivax malaria.

PubMed

Kitchener, Scott; Nasveld, Peter; Edstein, Michael D

2007-03-01

Tafenoquine was used to treat Plasmodium vivax malaria cases who had previously failed treatment with chloroquine and primaquine. Chloroquine was followed by a loading dose of tafenoquine (200 mg base/day for 3 days) and 200 mg a week was given for 8 weeks. One of 27 treated patients relapsed after 6 months of observation. A standard course of chloroquine administered with 8 weeks of tafenoquine may be more effective than chloroquine with primaquine (22.5 mg/day for 14 days) in preventing additional P. vivax relapses. Larger studies are required to optimize the combination, but our findings suggest that an extended use of tafenoquine may be required to prevent relapses of primaquine-tolerant strains of P. vivax malaria.

The Principal Hugoniot of Forsterite to 950 GPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Root, Seth; Townsend, Joshua P.; Davies, Erik

Forsterite (Mg 2SiO 4) single crystals were shock compressed to pressures between 200 and 950 GPa using independent plate–impact steady shocks and laser–driven decaying shock compression experiments. Additionally, we performed density functional theory–based molecular dynamics to aid interpretation of the experimental data and to investigate possible phase transformations and phase separations along the Hugoniot. We show that the experimentally obtained Hugoniot cannot distinguish between a pure liquid Mg 2SiO 4 and an assemblage of solid MgO plus liquid magnesium silicate. In conclusion, the measured reflectivity is nonzero and increases with pressure, which implies that the liquid is a poor electricalmore » conductor at low pressures and that the conductivity increases with pressure.« less

Experimental investigation of paraffin-based fuels for hybrid rocket propulsion

NASA Astrophysics Data System (ADS)

Galfetti, L.; Merotto, L.; Boiocchi, M.; Maggi, F.; DeLuca, L. T.

2013-03-01

Solid fuels for hybrid rockets were characterized in the framework of a research project aimed to develop a new generation of solid fuels, combining at the same time good mechanical and ballistic properties. Original techniques were implemented in order to improve paraffin-based fuels. The first strengthening technique involves the use of a polyurethane foam (PUF); a second technique is based on thermoplastic polymers mixed at molecular level with the paraffin binder. A ballistic characterization of paraffin-based hybrid rocket solid fuels was performed, considering pure wax-based fuels and fuels doped with suitable metal additives. Nano-Al powders and metal hydrides (magnesium hydride (MgH2), lithium aluminum hydride (LiAlH4 )) were used as fillers in paraffin matrices. The results of this investigation show a strong correlation between the measured viscosity of the melted paraffin layer and the regression rate: a decrease of viscosity increases the regression rate. This trend is due to the increasing development of entrainment phenomena, which strongly increase the regression rate. Addition of LiAlH4 (mass fraction 10%) can further increase the regression rate up to 378% with respect to the pure HTPB regression rate, taken as baseline reference fuel. The highest regression rates were found for the Solid Wax (SW) composition, added with 5% MgH2 mass fraction; at 350 kg/(m2s) oxygen mass flux, the measured regression rate, averaged in space and time, was 2.5 mm/s, which is approximately five times higher than that of the pure HTPB composition. Compositions added with nanosized aluminum powders were compared with those added with MgH2, using gel or solid wax.

Sensory profile, soluble sugars, organic acids, and mineral content in milk- and soy-juice based beverages.

PubMed

Andrés, Víctor; Tenorio, M Dolores; Villanueva, M José

2015-04-15

The juice industry has undergone a continuous innovation to satisfy the increasing healthy food demand by developing, among others, beverages based on fruits and milk or soybeans. The comparison among the sensory attributes between nineteen commercial mixed beverages showed significant differences in colour, sweetness, acidity, and consistency. Sucrose and citric acid were found in large proportion due to their natural presence or their addition. Potassium was the major macromineral (148-941 mg/L), especially in soy beverages. The low concentration of sodium in soy drinks is a healthy characteristic. The profile of inorganic anions has been included for the first time. Sulphate (39-278 mg/L) and phosphate (51-428 mg/L) were the predominant anions. High correlations were found between the percentage of fruit and consistency, fructose, malic acid, potassium and phosphate content (r(2)>0.790). Based on the data obtained, these beverages show pleasant organoleptic characteristics and constitute a good source of essential nutrients for regular consumers. Copyright © 2014 Elsevier Ltd. All rights reserved.

A web-based study of the relationship of duration of insulin pump infusion set use and fasting blood glucose level in adults with type 1 diabetes.

PubMed

Sampson Perrin, Alysa J; Guzzetta, Russell C; Miller, Kellee M; Foster, Nicole C; Lee, Anna; Lee, Joyce M; Block, Jennifer M; Beck, Roy W

2015-05-01

To evaluate the impact of infusion set use duration on glycemic control, we conducted an Internet-based study using the T1D Exchange's online patient community, Glu ( myGlu.org ). For 14 days, 243 electronically consented adults with type 1 diabetes (T1D) entered online that day's fasting blood glucose (FBG) level, the prior day's total daily insulin (TDI) dose, and whether the infusion set was changed. Mean duration of infusion set use was 3.0 days. Mean FBG level was higher with each successive day of infusion set use, increasing from 126 mg/dL on Day 1 to 133 mg/dL on Day 3 to 147 mg/dL on Day 5 (P<0.001). TDI dose did not vary with increased duration of infusion set use. Internet-based data collection was used to rapidly conduct the study at low cost. The results indicate that FBG levels increase with each additional day of insulin pump infusion set use.

Cost per remission and cost per response with infliximab, adalimumab, and golimumab for the treatment of moderately-to-severely active ulcerative colitis.

PubMed

Toor, Kabirraaj; Druyts, Eric; Jansen, Jeroen P; Thorlund, Kristian

2015-06-01

To determine the short-term costs per sustained remission and sustained response of three tumor necrosis factor inhibitors (infliximab, adalimumab, and golimumab) in comparison to conventional therapy for the treatment of moderately-to-severely active ulcerative colitis. A probabilistic Markov model was developed. This included an 8-week induction period, and 22 subsequent 2-week cycles (up to 1 year). The model included three disease states: remission, response, and relapse. Costs were from a Canadian public payer perspective. Estimates for the additional cost per 1 year of sustained remission and sustained response were obtained. Golimumab 100 mg provided the lowest cost per additional remission ($935) and cost per additional response ($701) compared with conventional therapy. Golimumab 50 mg yielded slightly higher costs than golimumab 100 mg. Infliximab was associated with the largest additional number of estimated remissions and responses, but also higher cost at $1975 per remission and $1311 per response. Adalimumab was associated with the largest cost per remission ($7430) and cost per response ($2361). The cost per additional remission and cost per additional response associated with infliximab vs golimumab 100 mg was $14,659 and $4753, respectively. The results suggest that the additional cost of 1 full year of remission and response are lowest with golimumab 100 mg, followed by golimumab 50 mg. Although infliximab has the highest efficacy, it did not exhibit the lowest cost per additional remission or response. Adalimumab produced the highest cost per additional remission and response.

In Vitro and Cryopreservation Techniques for Conservation of Snow Mountain Garlic.

PubMed

Mahajan, Ritu

2016-01-01

Garlic is an important medicinal herb of culinary value by imparting its flavors and odors to the food. Allicin, a notable flavonoid in garlic, is a powerful antibiotic and antifungal compound. Due to poor bioavailability, garlic is of limited use for oral human consumption. Being sexually sterile, propagation of garlic is done by individual cloves from a bulb which increases the chances of transfer of viral diseases. In this chapter, an efficient and improved regeneration protocol for explant establishment and shoot multiplication under in vitro conditions is described. A high rate of shoot multiplication is obtained on MS medium supplemented with 0.5 mg/l BAP, 1.0 mg/l KN, and 2.0 mg/l GA3. Addition of 1.0 mg/l NAA to MS medium resulted in rooting at the shoot bases. A detailed method for encapsulation of explant in sodium alginate beads and their cryopreservation using encapsulation-dehydration is also described.

Coordination Chemistry in magnesium battery electrolytes: how ligands affect their performance

DOE PAGES

Shao, Yuyan; Liu, Tianbiao L.; Li, Guosheng; ...

2013-11-04

Magnesium battery is potentially a safe, cost-effective, and high energy density technology for large scale energy storage. However, the development of magnesium battery has been hindered by the limited performance and the lack of fundamental understandings of electrolytes. Here, we present a coordination chemistry study of Mg(BH 4) 2 in ethereal solvents. The O donor denticity, i.e. ligand strength of the ethereal solvents which act as ligands to form solvated Mg complexes, plays a significant role in enhancing coulombic efficiency of the corresponding solvated Mg complex electrolytes. A new and safer electrolyte is developed based on Mg(BH4)2, diglyme and optimizedmore » LiBH4 additive. The new electrolyte demonstrates 100% coulombic efficiency, no dendrite formation, and stable cycling performance with the cathode capacity retention of ~90% for 300 cycles in a prototype magnesium battery.« less

Antioxidant activity, anti-proliferative activity, and amino acid profiles of ethanolic extracts of edible mushrooms.

PubMed

Panthong, S; Boonsathorn, N; Chuchawankul, S

2016-10-17

Biological activities of various mushrooms have recently been discovered, particularly, immunomodulatory and antitumor activities. Herein, three edible mushrooms, Auricularia auricula-judae (AA), Pleurotus abalonus (PA) and Pleurotus sajor-caju (PS) extracted using Soxhlet ethanol extraction were evaluated for their antioxidative, anti-proliferative effects on leukemia cells. Using the Folin-Ciocalteau method and Trolox equivalent antioxidant capacity assay, phenolics and antioxidant activity were found in all sample mushrooms. Additionally, anti-proliferative activity of mushroom extracts against U937 leukemia cells was determined using a viability assay based on mitochondrial activity. PA (0.5 mg/mL) and AA (0.25-0.5 mg/mL) significantly reduced cell viability. Interestingly, PS caused a hormetic-like biphasic dose-response. Low doses (0-0.25 mg/L) of PS promoted cell proliferation up to 140% relative to control, whereas higher doses (0.50 mg/mL) inhibited cell proliferation. Against U937 cells, AA IC 50 was 0.28 ± 0.04 mg/mL, which was lower than PS or PA IC 50 (0.45 ± 0.01 and 0.49 ± 0.001 mg/mL, respectively). Furthermore, lactate dehydrogenase (LDH) leakage conferred cytotoxicity. PS and PA were not toxic to U937 cells at any tested concentration; AA (0.50 mg/mL) showed high LDH levels and caused 50% cytotoxicity. Additionally, UPLC-HRMS data indicated several phytochemicals known to support functional activities as either antioxidant or anti-proliferative. Glutamic acid was uniquely found in ethanolic extracts of AA, and was considered an anti-cancer amino acid with potent anti-proliferative effects on U937 cells. Collectively, all mushroom extracts exhibited antioxidant effects, but their anti-proliferative effects were dose-dependent. Nevertheless, the AA extract, with highest potency, is a promising candidate for future applications.

Efficacy and safety of the human anti-IL-1beta monoclonal antibody canakinumab in rheumatoid arthritis: results of a 12-week, phase II, dose-finding study

PubMed Central

2011-01-01

Background Canakinumab is a fully human anti-interleukin IL-1beta monoclonal antibody, being investigated for the treatment of rheumatoid arthritis (RA). This multicenter, phase II, randomized, double-blind, placebo-controlled, parallel-group, dose-finding study investigated the efficacy and safety of canakinumab in patients with active RA despite ongoing therapy at stable doses of methotrexate. Methods Patients were randomized to receive one of four regimens, in addition to methotrexate, for 12 weeks: canakinumab 150 mg subcutaneously (SC) every 4 weeks (q4wk), canakinumab 300 mg SC (2 injections of 150 mg SC) every 2 weeks, a 600 mg intravenous loading dose of canakinumab followed by 300 mg SC every 2 weeks', or placebo SC every 2 weeks. Results Among 274 patients with evaluable efficacy data, the percentage of responders according to American College of Rheumatology 50 criteria (the primary endpoint, based on a 28-joint count) was significantly higher with canakinumab 150 mg SC q4wk than with placebo (26.5% vs. 11.4%, respectively; p = 0.028). Compared to placebo, this dosage of canakinumab was also associated with significantly more favorable responses at week 12 with respect to secondary endpoints including the Disease Activity Score 28, scores on the Health Assessment Questionnaire and Functional Assessment of Chronic Illness Therapy-Fatigue, swollen 28-joint count, and patient's and physician's global assessments of disease activity. No safety concerns were raised with canakinumab therapy, particularly with regard to infections. Few injection-site reactions occurred. Conclusion The addition of canakinumab 150 mg SC q4wk improves therapeutic responses among patients who have active RA despite stable treatment with methotrexate. Trial Registration (ClinicalTrials.gov identifier: NCT00784628) PMID:21736751

The Effect of Li Additions on Wear Properties of Al-Mg2Si Cast In-situ Composites

NASA Astrophysics Data System (ADS)

Ghorbani, M. R.; Emamy, M.; Ghiasinejad, J.; Malekan, A.

2010-06-01

Wear rate of a modified Al-Mg2Si composite was studied by the use of a conventional pin-on-disc technique. In-situ Al-Mg2Si composites (15, 20, 25 wt.%) were cast in a simple cylindrical mold. 0.3 wt.% Li was added into the molten composite to modify its microstructure. It has been found that Li addition decreases the mean size of primary Mg2Si particles. The wear behavior of different composites at different rates revealed that Li addition increases the wear properties of Al-15%Mg2Si to some extent but it did not have any significant influence on wear properties of two other composites.

Evaluation of Young’s modulus of MgB2 filaments in composite wires for the superconducting links for the high-luminosity LHC upgrade

NASA Astrophysics Data System (ADS)

Sugano, Michinaka; Ballarino, Amalia; Bartova, Barbora; Bjoerstad, Roger; Gerardin, Alexandre; Scheuerlein, Christian

2016-02-01

MgB2 wire is a promising superconductor for the superconducting links for the high-luminosity upgrade of the large Hadron collider at CERN. The mechanical properties of MgB2 must be fully quantified for the cable design, and in this study, we evaluate the Young’s modulus of MgB2 filaments in wires with a practical level of critical current. The Young’s moduli of MgB2 filaments by two different processes, in situ and ex situ, were compared. Two different evaluation methods were applied to an in situ MgB2 wire, a single-fiber tensile test and a tensile test after removing Monel. In addition, the Young’s modulus of the few-micron-thick Nb-Ni reaction layer in an ex situ processed wire was evaluated using a nanoindentation testing technique to improve the accuracy of analysis based on the rule of mixtures. The Young’s moduli of the in situ and ex situ MgB2 wires were in the range of 76-97 GPa and no distinct difference depending on the fabrication process was found.

Hydrogenation thermodynamics of melt-spun magnesium rich Mg-Ni nanocrystalline alloys with the addition of multiwalled carbon nanotubes and TiF3

NASA Astrophysics Data System (ADS)

Hou, Xiaojiang; Hu, Rui; Zhang, Tiebang; Kou, Hongchao; Li, Jinshan

2016-02-01

Based on the complexity of hydrogen absorption/desorption process and from the perspective of overall control, the as-cast Mg-10wt%Ni (Mg10Ni) alloy has been successively optimized by melt-spinning and surface catalyzed to realize the internal refinement as well as surface modification. The isothermal hydrogenation behavior of modified Mg-rich alloys has been investigated in this work. The results indicate that melt-spun Mg10Ni catalyzed by multiwalled carbon nanotubes (MWCNTs) coupling with TiF3 possesses superior activation properties and can absorb 6.23 wt% at 250 °C under 2.5 MPa. It is worth mentioning that the hydrogenation capacities of Mg10Ni-MWCNTs-TiF3 are 5.93 wt% and 5.99 wt% within the initial 1 min and 5 min, respectively. Meanwhile, the catalytic effect of MWCNTs and TiF3 has been discussed. The improved activation performance as well as the thermodynamics properties of Mg10Ni catalyzed by MWCNTs and TiF3 is attributed to the synergistic effect on dissociation of H2 molecules, diffusion of H-atoms and heterogeneous nucleation of hydrides.

Functional Response (FR) and Relative Growth Rate (RGR) Do Not Show the Known Invasiveness of Lemna minuta (Kunth)

PubMed Central

Boets, Pieter; Goethals, Peter L. M.

2016-01-01

Growing travel and trade threatens biodiversity as it increases the rate of biological invasions globally, either by accidental or intentional introduction. Therefore, avoiding these impacts by forecasting invasions and impeding further spread is of utmost importance. In this study, three forecasting approaches were tested and combined to predict the invasive behaviour of the alien macrophyte Lemna minuta in comparison with the native Lemna minor: the functional response (FR) and relative growth rate (RGR), supplemented with a combined biomass-based nutrient removal (BBNR). Based on the idea that widespread invasive species are more successful competitors than local, native species, a higher FR and RGR were expected for the invasive compared to the native species. Five different nutrient concentrations were tested, ranging from low (4 mgN.L-1 and 1 mgP.L-1) to high (70 mgN.L-1 and 21 mgP.L-1). After four days, a significant amount of nutrients was removed by both Lemna spp., though significant differences among L. minor and L. minuta were only observed at lower nutrient concentrations (lower than 17 mgN.L-1 and 6 mgP.L-1) with higher nutrient removal exerted by L. minor. The derived FR did not show a clear dominance of the invasive L. minuta, contradicting field observations. Similarly, the RGR ranged from 0.4 to 0.6 d-1, but did not show a biomass-based dominance of L. minuta (0.5 ± 0.1 d-1 versus 0.63 ± 0.09 d-1 for L. minor). BBNR showed similar results as the FR. Contrary to our expectations, all three approaches resulted in higher values for L. minor. Consequently, based on our results FR is sensitive to differences, though contradicted the expectations, while RGR and BBNR do not provide sufficient power to differentiate between a native and an invasive alien macrophyte and should be supplemented with additional ecosystem-based experiments to determine the invasion impact. PMID:27861603

Microwave properties of film Ba x Sr1 - x TiO3 ferroelectric variconds with a magnesium-containing additive

NASA Astrophysics Data System (ADS)

Tumarkin, A. V.; Tepina, E. R.; Nenasheva, E. A.; Kartenko, N. F.; Kozyrev, A. B.

2012-06-01

The electrophysical properties of bulk ceramics based on Ba x Sr1 - x TiO3 solid solutions with a Mg-containing additive and planar variconds based on ferroelectric films obtained by the ion-plasma sputtering of targets with different elemental compositions are studied. Controllability n( U) = C(0)/ C( U) and the dielectric loss tangent (tanδ) of ferroelectric variconds are measured as functions of the elemental composition of the ferroelectric. The figure of merit of the variconds is estimated, and the film composition providing the best electrophysical parameters is determined.

Fundamental Study of the Development and Evaluation of Biodegradable Mg-Y-Ca-Zr Alloys as Novel Implant Materials

NASA Astrophysics Data System (ADS)

Da-Tren Chou

Degradable metals hold considerable promise as materials which exhibit higher mechanical properties than degradable polymers while corroding over time to alleviate complications such as stress-shielding and infection that is inherent to permanent, bioinert metallic biomaterials. Specifically, degradable magnesium (Mg) alloys have emerged as a promising alternative for orthopedic and craniofacial applications due to their positive bone remodeling behavior, good biocompatibility, and relatively high strength compared to polymers while exhibiting similar stiffness to natural bone. Increasing the strength to maintain device integrity during degradation while simultaneously controlling the rapid corrosion of Mg to reduce the risk of hydrogen gas accumulation and toxicity are ongoing paramount goals for optimizing Mg alloys for musculoskeletal applications. In order to address these goals, novel Mg-Y-Ca-Zr based alloys were developed with alloying elements judiciously selected to impart favorable properties. Processing techniques including solution heat treatment combined with hot extrusion were employed to further enhance the desired properties of the material namely, controlled corrosion, high strength and ductility, and minimal toxic response. Increasing the Y content contributed to improved corrosion resistance yielding corrosion rates similar to commercial Mg alloys. Hot extrusion was employed to reduce the grain size, thereby improving mechanical properties through the Hall-Petch relation. Extrusion yielded extremely high strength relative to other Mg alloys, values approaching that of iron-based alloys, due to the presence of Mg12YZn, a long period stacking order phase that served to impede dislocation propagation. Both as-cast and extruded Mg-Y-Ca-Zr alloys demonstrated excellent in vitro cytocompatibility eliciting high viability and proliferation of MC3T3 pre-osteoblast cells and human mesenchymal stem cells. Alloying elements Y and Zr were specifically shown to improve cell proliferation. Finally, implantation of Mg-Y-Ca-Zr based alloys into the mouse subcutaneous tissue and intramedullary cavities of fractured rat femurs resulted in a normal host response and fracture healing, without eliciting any local or systemic toxicity. Thus, the alloys investigated in this work demonstrated great potential for applications as orthopedic and craniofacial implant biomaterials, warranting additional pre-clinical safety and efficacy trials that will be conducted in the near future.

Efficacy and safety of a combination of azithromycin and chloroquine for the treatment of uncomplicated Plasmodium falciparum malaria in two multi-country randomised clinical trials in African adults.

PubMed

Sagara, Issaka; Oduro, Abraham R; Mulenga, Modest; Dieng, Yemou; Ogutu, Bernhards; Tiono, Alfred B; Mugyenyi, Peter; Sie, Ali; Wasunna, Monique; Kain, Kevin C; Djimdé, Abdoulaye A; Sarkar, Shirsendu; Chandra, Richa; Robbins, Jeffery; Dunne, Michael W

2014-11-25

Given increasing rates of resistance to existing therapy, new options for treatment and prophylaxis of malaria are needed. Two randomised, comparative, non-inferiority studies were conducted in Africa, one double-blinded and one open-label. Adults with fever, a positive peripheral blood smear, and a positive rapid diagnostic test for Plasmodium falciparum were randomised in both studies to either azithromycin (AZ) 1,000 mg plus chloroquine (CQ) 600-mg base (AZCQ 1,000 mg) once daily for three days or mefloquine hydrochloride (MQ) 1,250 mg (split dose). In the first study, an additional regimen of AZ 500 mg plus CQ 600-mg base (AZCQ 500 mg) once daily for three days was included. All study participants were hospitalised until three consecutive daily blood smears were negative for asexual P. falciparum parasitaemia. Study participants were evaluated weekly for 42 days, with Day 28 polymerase chain reaction (PCR)-corrected parasitological clearance rate as primary endpoint. A total of 467 subjects were randomised in the two studies. At 28 days' follow-up, PCR-corrected parasitological clearance rates in the per protocol population in the first study were 101/103 (98%) with AZCQ 1,000 mg compared with 102/103 (99%) with MQ (95% confidence interval [CI]: -5.2, 3.3). The AZCQ 500-mg regimen was stopped during an interim study review (six [86%] clearance of seven evaluable; two lost to follow-up). In the second study, clearance rates were similar: AZCQ 1,000 mg 107/107 (100%) vs MQ 111/112 (99%; 95% CI: -1.8, 3.6). Among the participating countries, in vitro CQ resistance based on pfcrt mutation frequency in the baseline isolates across both studies ranged from 20.8% (Zambia) to 96.1% (Uganda). Serious adverse events (AEs; all causality) were observed more frequently with MQ compared with AZCQ (four vs one, respectively), though discontinuations for AEs were similar (four vs three, respectively). Common AEs in the AZ-containing arms included pruritus, vomiting, dizziness, and headache. Among adults with symptomatic uncomplicated falciparum malaria in Africa, the combination of AZ 1,000 mg and CQ 600-mg base once daily for three days resulted in Day 28 PCR-corrected parasitological clearance rates of ≥98% and was non-inferior to treatment with MQ. AZCQ was well tolerated. ClinicalTrials.gov identifiers NCT00082576 and NCT00367653.

The Effects of Dy Addition on Microstructure and Mechanical Properties of the As-Cast Mg-5Al-3Ca-2Nd Alloys.

PubMed

Son, Hyeon-Taek; Kim, Yong-Ho; Yoo, Hyo-Sang

2018-03-01

The microstructure of the as-cast Mg-5Al-3Ca-2Nd-xDy alloys consists of α-Mg matrix, (Mg, Al)2Ca eutectic phase, Al-Nd and Al-Dy intermetallic compounds. α-Mg matrix morphology was changed from dendritic to equiaxed with the increase Dy addition. And grain size was remarkably refined. As Dy content was increased, yield strength was improved due to the refined grains and the homogeneous distribution of Al-Dy phase.

Effects of pharmacological manipulation of the kappa opioid receptors on the aversive effects of nicotine.

PubMed

Ward, Melissa; Norman, Haval; D'Souza, Manoranjan S

2018-02-15

Nicotine, an addictive component of tobacco smoke, produces both rewarding and aversive effects. Increasing the aversive effects of nicotine may help in promoting smoking cessation. However, neural targets mediating the aversive effects of nicotine have not been fully identified. In this study, we evaluated the role of kappa opioid receptors (KORs) in the aversive effects of nicotine (0.4 mg/kg, base; s.c.) using the nicotine-induced conditioned taste aversion (CTA) model in Wistar rats. The KORs were activated using the selective KOR agonist (±)U-50,488H (0, 0.03, 0.15 & 0.3mg/kg; s.c.) and inhibited using the KOR antagonist nor-binaltorphimine (nor-BNI; 0, 15 & 30mg/kg; s.c.) in separate groups of rats using a between-subjects design. Pretreatment with the KOR agonist (±)U-50,488H (0.3mg/kg) significantly increased aversion for the nicotine-associated solution. Additionally, (±)U-50,488H (0.3mg/kg) on its own induced aversion to the flavored solution associated with it even in the absence of nicotine, suggesting that the KOR agonist induced increase in nicotine-induced aversion was an additive effect. Interestingly, administration of the KOR antagonist nor-BNI (30mg/kg) prior to conditioning with nicotine/saline, but not after conditioning with nicotine/saline, attenuated nicotine-induced aversive effects compared to saline controls. Taken together, these data suggest a role for KORs in the aversive effects of nicotine. Copyright © 2017 Elsevier B.V. All rights reserved.

Inhibition effects of high calcium concentration on anaerobic biological treatment of MSW leachate.

PubMed

Xia, Yi; He, Pin-Jing; Pu, Hong-Xia; Lü, Fan; Shao, Li-Ming; Zhang, Hua

2016-04-01

With the increasing use of municipal solid waste incineration (MSWI) and more stringent limits on landfilling of organic waste, more MSWI bottom ash is being landfilled, and the proportion of inorganic wastes in landfills is increasing, causing the increased Ca concentrations in landfill leachate. In this research, the inhibition effect of Ca concentration on the anaerobic treatment of landfill leachate was studied using a biochemical methane potential experiment. Slight inhibition of methane production occurred when the addition of Ca concentration was less than 2000 mg/L. When the addition of Ca concentration was between 6000 and 8000 mg/L, methane production was significantly reduced (to 29.4-34.8 % of that produced by the BLK reactor), and the lag phase was increased from 8.55 to 16.32 d. Moreover, when the dosage of Ca concentration increased from zero to 8000 mg/L, reductions in solution Ca concentration increased from 929 to 2611 mg/L, and the proportion of Ca in the residual sludge increased from 22.58 to 46.87 %. Based on the results, when the dosage of Ca concentration was less than 4000 mg/L, the formation of Ca precipitates on the surface of sludge appeared to prevent mass transfer and was the dominant reason for the reduction in methane production and sludge biomass. At higher Ca concentrations (6000-8000 mg/L), the severe inhibition of methane production appeared to be caused by the toxic effect of highly concentrated Ca on sludge as well as mass transfer blockage.

Production of 8-hydroxydaidzein from soybean extract by Aspergillus oryzae KACC 40247.

PubMed

Seo, Min-Ho; Kim, Bi-Na; Kim, Kyoung-Rok; Lee, Ki Won; Lee, Choong-Hwan; Oh, Deok-Kun

2013-01-01

Aspergillus oryzae KACC 40247 was selected from among 60 fungal strains as an effective 7,8,4'-trihydroxyisoflavone (8-hydroxydaidzein)-producing fungus. The optimal culture conditions for production by this strain in a 7-L fermentor were found to be 30 °C, pH 6, and 300 rpm. Under these conditions, A. oryzae KACC 40247 produced 62 mg/L of 8-hydroxydaidzein from soybean extract in 30 h, with a productivity of 2.1 mg/L/h. These are the highest production and productivity for 8-hydroxydaidzein ever reported. To increase production, several concentrations of daidzin and of daidzein as precursor were added at several culture times. The optimal addition time and concentration for daidzin were 12 h and 1,248 mg/L, and those for daidzein were 12 h and 254 mg/L respectively. Maximum production and productivity for 8-hydroxydaidzein with the addition of daidzein were 95 mg/L and 3.2 mg/L/h respectively, and those with the addition of daidzin were 160 mg/L and 4.4 mg/L/h respectively.

[Experiments with sausage meat on the formation of N epsilon-carboxymethyllysine].

PubMed

Hartkopf, J; Erbersdobler, H F

1995-07-01

In model experiments the influence of ingredients normally used for sausage production to a meat homogenate on the formation of N epsilon-carboxymethyllysine (CML) was investigated. The formation of CML is obviously more promoted from the reaction of ascorbate with lysine than from that of glucose with lysine. The addition of ascorbate in a practical concentration yielded 35 mg, the addition of glucose only 23 mg compared to 17 mg CML/kg protein in the control sample. The addition of diphosphate in a practical concentration besides glucose significantly increased the CML values from 23 mg to 30 mg CML/kg protein. On the other hand, nitrite did not enhance the formation of CML (21 mg/kg protein) in the sausage when used in concentrations usually applied in meat processing. Generally the values found in the meat products are quite low compared to data in other foods like milk products.

Distinct Lipoprotein Curves in Normal Weight, Overweight, and Obese Children and Adolescents.

PubMed

Interator, Hagar; Lebenthal, Yael; Hoshen, Moshe; Safra, Inbar; Balicer, Ran; Leshno, Moshe; Shamir, Raanan

2017-12-01

Pediatric lipoprotein curves are based on population-based samples. As obesity, may alter lipoprotein levels, cutoffs not adjusted for body mass index (BMI) are potentially inappropriate. We aimed to develop distinct serum lipid curves based on sex- and BMI-percentiles for children and adolescents. Cross-sectional analysis included all healthy children and adolescents (age range 2-17 years) with available serum lipid concentrations (n = 152,820 of approximately 1.2 million children and adolescents per study year). These children and adolescents were categorized according to sex- and age-stratified BMI-percentiles: 100,375 normal weight (5th-85th percentile), 26,028 overweight (85th-95th percentile) and 26,417 obese (≥95th percentile) individuals. Excluded were individuals with hyperlipidemia, gastrointestinal disease, thyroid disease and lipid-lowering medications. Lambda-Mu-Sigma, smoothed percentile lipid curves were computed. Obese children had a lipid profile pattern throughout childhood and adolescence similar to that of normal weight subjects but with a significant upward shift in total cholesterol (TC), low-density lipoprotein cholesterol (LDL-C), non-high-density lipoprotein cholesterol (non-HDL-C), and triglycerides (TGs) and a downward shift in high-density lipoprotein-cholesterol (HDL-C). Obese boys had 13 mg/dL higher TC levels (P < 0.001), 11 mg/dL higher LDL-C levels, 15 mg/dL higher non-HDL-C levels, and 5 mg/dL lower HDL-C levels (P < 0.001). Obese girls had 6 mg/dL higher TC levels, 7 mg/dL higher LDL-C levels, 11 mg/dl higher non-HDL-C levels, and 6 mg/dL lower HDL-C levels (P < 0.001). Across a large, nationally representative cohort of children and adolescents, lipoprotein levels were found to vary in relation to weight status. On the basis of these findings, it is suggested that when evaluating the lipid profile in the pediatric population, in addition to sex-based curves, clinical decision making may require consideration of BMI-stratified curves.

Improved hydrogen absorption and desorption kinetics of magnesium-based alloy via addition of yttrium

NASA Astrophysics Data System (ADS)

Yang, Tai; Li, Qiang; Liu, Ning; Liang, Chunyong; Yin, Fuxing; Zhang, Yanghuan

2018-02-01

Yttrium (Y) is selected to modify the microstructure of magnesium (Mg) to improve the hydrogen storage performance. Thereby, binary alloys with the nominal compositions of Mg24Yx (x = 1-5) are fabricated by inexpensive casting technique. Their microstructure and phase transformation during hydriding and dehydriding process are characterized by using X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy analysis. The isothermal hydrogen absorption and desorption kinetics are also measured by a Sievert's-type apparatus at various temperatures. Typical multiphase structures of binary alloy can be clearly observed. All of these alloys can reversibly absorb and desorb large amount of hydrogen at proper temperatures. The addition of Y markedly promotes the hydrogen absorption kinetics. However, it results in a reduction of reversible hydrogen storage capacity. A maximum value of dehydrogenation rate is observed with the increase of Y content. The Mg24Y3 alloy has the optimal desorption kinetic performance, and it can desorb about 5.4 wt% of hydrogen at 380 °C within 12 min. Combining Johnson-Mehl-Avrami kinetic model and Arrhenius equation, the dehydrogenation activation energy of the alloys are evaluated. The Mg24Y3 alloy also has the lowest dehydrogenation activation energy (119 kJ mol-1).

Ergot Alkaloids in Fattening Chickens (Broilers): Toxic Effects and Carry over Depending on Dietary Fat Proportion and Supplementation with Non-Starch-Polysaccharide (NSP) Hydrolyzing Enzymes.

PubMed

Dänicke, Sven

2017-03-28

Ergot alkaloids (EA) are mycotoxins produced by Claviceps purpurea . EA-toxicity is poorly characterized for fattening chickens. Therefore, a dose-response study was performed to identify the lowest, and no observed adverse effect levels (LOAEL and NOAEL, respectively) based on several endpoints. Non-starch-polysaccharide (NSP) cleaving enzyme addition and dietary fat content were additionally considered as factors potentially influencing EA-toxicity. Feed intake was proven to respond most sensitively to the EA presence in the diets. This sensitivity appeared to be time-dependent. While LOAEL corresponded to a total dietary EA content of 5.7 mg/kg until Day 14 of age, it decreased to 2.03 mg/kg when birds were exposed for a period of 35 days. Consequently, NOAEL corresponded to an EA content of 2.49 mg/kg diet until Day 14 of age, while 1.94 mg/kg diet applied until Day 35 of age. Liver lesions indicating enzyme activities in serum were increased after 14 days of exposure. Dietary fat content and NSP-enzyme supplementation modified EA toxicity in an interactive manner. The EA residues in serum, bile, liver and breast meat were <5 ng/g suggesting a negligible carry over of intact EA.

Ergot Alkaloids in Fattening Chickens (Broilers): Toxic Effects and Carry over Depending on Dietary Fat Proportion and Supplementation with Non-Starch-Polysaccharide (NSP) Hydrolyzing Enzymes

PubMed Central

Dänicke, Sven

2017-01-01

Ergot alkaloids (EA) are mycotoxins produced by Claviceps purpurea. EA-toxicity is poorly characterized for fattening chickens. Therefore, a dose–response study was performed to identify the lowest, and no observed adverse effect levels (LOAEL and NOAEL, respectively) based on several endpoints. Non-starch-polysaccharide (NSP) cleaving enzyme addition and dietary fat content were additionally considered as factors potentially influencing EA-toxicity. Feed intake was proven to respond most sensitively to the EA presence in the diets. This sensitivity appeared to be time-dependent. While LOAEL corresponded to a total dietary EA content of 5.7 mg/kg until Day 14 of age, it decreased to 2.03 mg/kg when birds were exposed for a period of 35 days. Consequently, NOAEL corresponded to an EA content of 2.49 mg/kg diet until Day 14 of age, while 1.94 mg/kg diet applied until Day 35 of age. Liver lesions indicating enzyme activities in serum were increased after 14 days of exposure. Dietary fat content and NSP-enzyme supplementation modified EA toxicity in an interactive manner. The EA residues in serum, bile, liver and breast meat were <5 ng/g suggesting a negligible carry over of intact EA. PMID:28350362

Asymmetry induces Q-band split in the electronic excitations of magnesium porphyrin

NASA Astrophysics Data System (ADS)

Jiang, Xiankai; Gao, Yi; Lal, Ratnesh; Hu, Jun; Song, Bo

2018-07-01

The electronic excitations of magnesium porphyrin (MgP), a molecular model for understanding the physics in light harvesting by biological systems, have been studied extensively. However, the theoretical underpinning of experimental measurements is still lacking, especially about the sub-bands in absorption spectrum. Here we propose that an asymmetry of MgP based on the uneven charge distribution of pyrrole rings and the linear structure of sp hybridised orbitals in Mg can largely influence the electronic excitations. Upon a very weak asymmetry of Mg-pyrrole bindings in MgP being introduced through the uneven distribution of charge, three different excitations are observed in the Q-band region of the experimental spectrum. Additionally, the predicted B-band excitations are highly correlated (10-2 eV level) with experimental measurements. In contrast, without this asymmetry, there are only two degenerate excitations in the Q-band region, and low agreement (10-1 eV level) of the B-band excitations with the experiment. The key physics of the unexpected and observable asymmetry in MgP is the ability of Mg to form sp hybridised orbitals on the third shell upon Mg binding to the nitrogen of pyrrole ring. Our findings provide new insight for high-energy efficiency of natural as well as artificial light-harvesting system for energy challenge.

Development of an Mg-Based Alloy with a Hydrogen-Storage Capacity over 6 wt% by Adding Graphene

NASA Astrophysics Data System (ADS)

Choi, Eunho; Kwak, Young Jun; Song, Myoung Youp

2018-06-01

Graphene (multilayer graphene) was chosen as an additive to improve the hydrogen uptake and release properties of magnesium (Mg). Five weight percent of graphene was added to pre-milled Mg by milling in hydrogen (reaction-involving milling). The hydrogen uptake and release properties of the graphene-added Mg were investigated. The activation of Mg-5graphene, which was prepared by adding 5 wt% graphene to Mg pre-milled for 24 h, was completed after the second cycle (cycle number, CN = 2). Mg-5graphene had a high effective hydrogen-storage capacity (the quantity of hydrogen absorbed for 60 min) of 6.21 wt% at CN = 3 at 593 K in 12 bar H2. At CN = 1, Mg-5graphene released 0.46 wt% hydrogen for 10 min and 4.99 wt% hydrogen for 60 min. Milling in hydrogen is believed to create defects (leading to facilitation of nucleation), produce cracks and clean surfaces (leading to increase in reactivity), and decrease particle size (leading to diminution of diffusion distances or increasing the flux of diffusing hydrogen atoms). The added graphene is believed to have helped the sample have higher hydrogen uptake and release rates, weakly but partly, by dispersing heat rapidly.

Interlayer-Spacing-Regulated VOPO4 Nanosheets with Fast Kinetics for High-Capacity and Durable Rechargeable Magnesium Batteries.

PubMed

Zhou, Limin; Liu, Qi; Zhang, Zihe; Zhang, Kai; Xiong, Fangyu; Tan, Shuangshuang; An, Qinyou; Kang, Yong-Mook; Zhou, Zhen; Mai, Liqiang

2018-06-25

Owing to the low-cost, safety, dendrite-free formation, and two-electron redox properties of magnesium (Mg), rechargeable Mg batteries are considered as promising next-generation secondary batteries with high specific capacity and energy density. However, the clumsy Mg 2+ with high polarity inclines to sluggish Mg insertion/deinsertion, leading to inadequate reversible capacity and rate performance. Herein, 2D VOPO 4 nanosheets with expanded interlayer spacing (1.42 nm) are prepared and applied in rechargeable magnesium batteries for the first time. The interlayer expansion provides enough diffusion space for fast kinetics of MgCl + ion flux with low polarization. Benefiting from the structural configuration, the Mg battery exhibits a remarkable reversible capacity of 310 mAh g -1 at 50 mA g -1 , excellent rate capability, and good cycling stability (192 mAh g -1 at 100 mA g -1 even after 500 cycles). In addition, density functional theory (DFT) computations are conducted to understand the electrode behavior with decreased MgCl + migration energy barrier compared with Mg 2+ . This approach, based on the regulation of interlayer distance to control cation insertion, represents a promising guideline for electrode material design on the development of advanced secondary multivalent-ion batteries. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Growth behavior and growth rate dependency in LEDs performance for Mg-doped a-plane GaN

NASA Astrophysics Data System (ADS)

Song, Keun-Man; Kim, Jong-Min; Lee, Dong-Hun; Shin, Chan-Soo; Ko, Chul-Gi; Kong, Bo-Hyun; Cho, Hyung-Koun; Yoon, Dae-Ho

2011-07-01

We investigated the influence of growth rate of Mg-doped a-plane GaN on the surface morphological and electrical properties, and the characteristics of InGaN-based nonpolar LEDs. Mg-doped a-plane GaN layers were grown on r-plane sapphire substrate by metalorganic chemical vapor deposition (MOCVD). Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and cathode luminescence (CL) analysis exhibited that the surface morphology changed from stripe features with large triangular pits to rough and rugged surface with small asymmetric V-shape pits, as the growth rate increased. The Mg incorporation into a-plane GaN layers increased with increasing growth rate of Mg-doped a-plane GaN, while the activation efficiency of Mg dopants decreased in a-plane GaN. Additionally, it was found that operation voltage at 20 mA decreased in characteristics of LEDs, as the growth rate of Mg-doped a-plane GaN decreased. Meanwhile, the EL intensity of LEDs with p-GaN layers grown at higher growth rate was improved compared to that of LEDs with p-GaN layers grown at lower growth rate. Such an increase of EL intensity is attributed to the rougher surface morphology with increasing growth rate of Mg-doped a-plane GaN.

Calibration and Limitations of the Mg II Line-based Black Hole Masses

NASA Astrophysics Data System (ADS)

Woo, Jong-Hak; Le, Huynh Anh N.; Karouzos, Marios; Park, Dawoo; Park, Daeseong; Malkan, Matthew A.; Treu, Tommaso; Bennert, Vardha N.

2018-06-01

We present single-epoch black hole mass ({M}BH}) calibrations based on the rest-frame ultraviolet (UV) and optical measurements of Mg II 2798 Å and Hβ 4861 Å lines and the active galactic nucleus (AGN) continuum, using a sample of 52 moderate-luminosity AGNs at z ∼ 0.4 and z ∼ 0.6 with high-quality Keck spectra. We combine this sample with a large number of luminous AGNs from the Sloan Digital Sky Survey to increase the dynamic range for a better comparison of UV and optical velocity and luminosity measurements. With respect to the reference {M}BH} based on the line dispersion of Hβ and continuum luminosity at 5100 Å, we calibrate the UV and optical mass estimators by determining the best-fit values of the coefficients in the mass equation. By investigating whether the UV estimators show a systematic trend with Eddington ratio, FWHM of Hβ, Fe II strength, or UV/optical slope, we find no significant bias except for the slope. By fitting the systematic difference of Mg II-based and Hβ-based masses with the L 3000/L 5100 ratio, we provide a correction term as a function of the spectral index as ΔC = 0.24 (1 + α λ ) + 0.17, which can be added to the Mg II-based mass estimators if the spectral slope can be well determined. The derived UV mass estimators typically show >∼0.2 dex intrinsic scatter with respect to the Hβ-based {M}BH}, suggesting that the UV-based mass has an additional uncertainty of ∼0.2 dex, even if high-quality rest-frame UV spectra are available.

Effects of NaBF4 + NaF on the Tensile and Impact Properties of Al-Si-Mg-Fe Alloys

NASA Astrophysics Data System (ADS)

Chen, Zongning; Wang, Tongmin; Zhao, Yufei; Zheng, Yuanping; Kang, Huijun

2015-05-01

NaBF4 + NaF were found to play three roles, i.e., Fe-eliminator, grain refiner, and eutectic modifier, in treating A356 alloy with a high Fe content. The joint effects led to significant improvement in both tensile and impact properties of thus treated alloy. The multiple reactions between the NaBF4 + NaF and Al-Si-Mg-Fe system are suggested to form Fe2B, AlB2, and Na in the melt, as per thermodynamic analysis. The three are responsible for Fe removal, grain refinement, and eutectic modification, respectively. When NaBF4 and NaF are mixed in weight ratio of 1:1, an optimum addition rate is in the range between 1.0 and 2.0 wt pct for treating AlSi7Mg0.3Fe0.65 alloy, based on the results of tensile and impact tests. Excessive addition of the salt may deteriorate the mechanical properties of the alloy, basically owing to overmodification of Si and contamination of salt inclusions.

The Mechanisms of Dispersion Strengthening and Fracture in Al-based XD (TM) Alloys

NASA Technical Reports Server (NTRS)

Aiken, R. M., Jr.

1990-01-01

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength, and the fracture toughness of metal matrix composites of both pure aluminum and Al(4 percent)Cu(1.5 percent)Mg with 0 to 15 vol percent TiB2 were examined. Higher TiB2 volume fractions increased the tensile yield strength both at room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. The fracture toughness of the Al(4 percent)Cu(1.5 percent)Mg alloys decreased rapidly with TiB2 additions of 0 to 5 vol percent and more slowly with TiB2 additions of 5 to 15 vol percent. Fracture toughness appears to be independent of TiB2 particle size. The isothermal-aging response of the precipitation strengthened Al(4 percent)Cu(1.5 percent)Mg alloys was not altered by the presence of TiB2.

Multicentre phase II studies evaluating imatinib plus hydroxyurea in patients with progressive glioblastoma.

PubMed

Reardon, D A; Dresemann, G; Taillibert, S; Campone, M; van den Bent, M; Clement, P; Blomquist, E; Gordower, L; Schultz, H; Raizer, J; Hau, P; Easaw, J; Gil, M; Tonn, J; Gijtenbeek, A; Schlegel, U; Bergstrom, P; Green, S; Weir, A; Nikolova, Z

2009-12-15

We evaluated the efficacy of imatinib mesylate in addition to hydroxyurea in patients with recurrent glioblastoma (GBM) who were either on or not on enzyme-inducing anti-epileptic drugs (EIAEDs). A total of 231 patients with GBM at first recurrence from 21 institutions in 10 countries were enrolled. All patients received 500 mg of hydroxyurea twice a day. Imatinib was administered at 600 mg per day for patients not on EIAEDs and at 500 mg twice a day if on EIAEDs. The primary end point was radiographic response rate and secondary end points were safety, progression-free survival at 6 months (PFS-6), and overall survival (OS). The radiographic response rate after centralised review was 3.4%. Progression-free survival at 6 months and median OS were 10.6% and 26.0 weeks, respectively. Outcome did not appear to differ based on EIAED status. The most common grade 3 or greater adverse events were fatigue (7%), neutropaenia (7%), and thrombocytopaenia (7%). Imatinib in addition to hydroxyurea was well tolerated among patients with recurrent GBM but did not show clinically meaningful anti-tumour activity.

Development of a beverage benchtop prototype based on sweet potato peels: optimization of antioxidant activity by a mixture design.

PubMed

Anastácio, Ana; Carvalho, Isabel Saraiva de

2015-08-01

A beverage benchtop prototype related to oxidative stress protection was developed based on sweet potato peels phenolics. Formula components were sweet potato peel (Ipomoeas batatas L.) aqueous extract (SPPE), sweet potato leaves water extract (SPLE) and honey solution (HonS). According to linear squares regression (LSR) models, SPLE presented higher additive effect on total phenolic content (TPC), FRAP and DPPH than the other components. All antagonist interactions were not significant. The optimum formula obtained by artificial neural networks (ANN) analysis was 50.0% of SPPE, 21.5% of SPLE and 28.5% of HonS. Predicted responses of TPC, FRAP, DPPH and soluble solids were 309 mg GAE/L, 476 mg TE/L, 1098 mg TE/L and 12.3 °Brix, respectively. Optimization with LSR models was similar to ANN. Beverage prototype results positioned next to commercial vegetable and fruit beverages, thus it has an interesting potential to the market of health and wellness.

Microstructure and bio-corrosion behaviour of Mg-5Zn-0.5Ca -xSr alloys as potential biodegradable implant materials

NASA Astrophysics Data System (ADS)

Yan, Li; Zhou, Jiaxing; Sun, Zhenzhou; Yang, Meng; Ma, Liqun

2018-04-01

Magnesium alloys are widely studied as biomedical implants owing to their biodegradability. In this work, novel Mg-5Zn-0.5Ca-xSr (x = 0, 0.14, 0.36, 0.50, 0.70 wt%) alloys were prepared as biomedical materials. The influence of strontium (Sr) addition on the microstructure, corrosion properties and corrosion morphology of the as-cast Mg-5Zn-0.5Ca-xSr alloys is investigated by a variety of techniques such as scanning electron microscopy, x-ray diffraction, and electrochemical measurements. The Sr-free alloy is composed of three phases, namely, α-Mg, CaMg2 and Ca2Mg6Zn3, while the alloys with the Sr addition consist of α-Mg, CaMg2 and Ca2Mg6Zn3 and Mg17Sr2. Corrosion experiments in Hank’s solution show that the addition of a small amount of Sr can improve the corrosion resistance of the Mg-5Zn-0.5Ca alloy. The corrosion products include Mg(OH)2, Zn(OH)2, Ca(OH)2, and HA (Ca5(PO4)3(OH)). Mg-5Zn-0.5Ca-0.36Sr alloy has the minimum weight loss rate (0.68 mm/a), minimal hydrogen evolution (0.08 ml/cm2/d) and minimum corrosion current density (7.4 μA/cm2), indicating that this alloy shows the best corrosion resistance.

To evaluate the effect of various magnesium stearate polymorphs using powder rheology and thermal analysis.

PubMed

Okoye, Patrick; Wu, Stephen H; Dave, Rutesh H

2012-12-01

The effects of magnesium stearate (MgSt) polymorphs-anhydrate (MgSt-A), monohydrate (MgSt-M), and dihydrate (MgSt-D)-on rheological properties of powders were evaluated using techniques such as atomic analysis and powder rheometry. Additional evaluation was conducted using thermal analysis, micromeritics, and tableting forces. In this study, binary ratios of neat MgSt polymorphs were employed as lubricants in powder blends containing acetaminophen (APAP), microcrystalline cellulose (MCC), and lactose monohydrate (LAC-M). Powder rheometry was studied using permeability, basic flow energy (BFE), density, and porosity analysis. Thermal conductivity and differential scanning calorimetric analysis of MgSt polymorphs were employed to elucidate MgSt effect on powder blends. The impact of MgSt polymorphs on compaction characteristics were analyzed via tablet compression forces. Finally, the distribution of atomized magnesium (Mg) ions as a function of intensity was evaluated using laser-induced breakdown spectroscopy (LIBS) on tablets. The results from LIBS analysis indicated the dependency of the MgSt polymorphic forms on the atomized Mg ion intensity, with higher Mg ion intensity suggesting higher lubricity index (i.e. greater propensity to over-lubricate). The results from lubricity index suggested the tendency of blends to over-lubricate based on the MgSt polymorphic forms. Finally, tableting forces suggested that MgSt-D and MgSt-A offered processing benefits such as lower ejection and compression forces, and that MgSt-M showed the most stable compression force in single or combined polymorphic ratios. These results suggested that the initial moisture content, crystal arrangement, intra- and inter-molecular packing of the polymorphs defined their effects on the rheology of lubricated powders.

Spectroscopic, thermal, and electrical properties of MgO/ polyvinyl pyrrolidone/ polyvinyl alcohol nanocomposites

NASA Astrophysics Data System (ADS)

Mohammed, Gh.; El Sayed, Adel M.; Morsi, W. M.

2018-04-01

In this study, we aimed to control the optical and electrical properties of polyvinyl alcohol (PVA) in order to broaden its industrial and technological applications, which we achieved by blending PVA with polyvinyl pyrrolidone (PVP) and adding sol-gel prepared MgO nanopowder. The blended film and nanocomposite films were prepared using the solution casting technique. X-ray diffraction analyses showed that the crystallite size was ∼18.4 nm for MgO and the highest degree of crystallinity (XC) in the films was about 24.34% at 1.0 wt% MgO. High resolution transmission electron microscopy determined the nanoribbon morphology of MgO. Scanning electron microscopy (SEM) indicated the uniform distribution of the MgO nanoribbons on the surfaces of the PVA/PVP films. SEM and Fourier transform infrared spectroscopy also confirmed the interaction between the blend and MgO fillers. The effects of the additives on the glass transition (Tg) and melting (Tm) temperatures were evaluated by differential thermal analysis and differential scanning calorimetry. The appearance of one melting point confirmed the miscibility of the two polymers. According to ultraviolet-visible-near infrared spectroscopy measurements, the optical properties and optical constants of PVA could be adjusted by the addition of PVP and MgO, where the optical band gap (Eg) determined for PVA increased with the PVP content, whereas it decreased to 4.8 eV as the MgO content increased. The DC conductivity (σdc) of the films increased whereas the activation energy (Ea) decreased after the addition of MgO, possibly because the nanoribbon shape fixed the preferred conducting pathways. In addition, MgO could break the H-bond in sbnd OH groups of the blends to allow the free movement of the molecular chains.

Characteristics of Pt-K/MgAl2O4 lean NOx trap catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Do Heui; Mudiyanselage, Kumudu K.; Szanyi, Janos

2012-04-30

We report the various characteristics of Pt-K/MgAl{sub 2}O{sub 4} lean NOx trap (LNT) catalysts including the effect of K loading on nitrate formation/decomposition, NOx storage activity and durability. Upon the adsorption of NO{sub 2} on K/MgAl{sub 2}O{sub 4} samples, potassium nitrates formed on Mg-related sites in MgAl{sub 2}O{sub 4} support are observed, in addition to the typical two potassium nitrates (ionic and bidentate) formed also on Al{sub 2}O{sub 3} supported sample. Based on NO{sub 2} TPD and FTIR results, the Mg-bound KNO{sub 3} thermally decompose at higher temperature than Al-bound KNO{sub 3}, implying its superior thermal stability. At a potassiummore » loading of 5wt%, the temperature of maximum NOx uptake (T{sub max}) is 300 C. Increasing the potassium loading from 5wt% to 10 wt%, the T{sub max} gradually shifted from 300 C to 450 C, indicating the dependence of T{sub max} on the potassium loading. However, increase in potassium loading above 10 wt% only gives rise to the reduction in the overall NOx storage capacity. This work also underlines the obstacles these materials have prior to their practical application (e.g., durability and sulfur poisoning/ removal). This work provides fundamental understanding of Pt-K/MgAl{sub 2}O{sub 4}-based lean NOx trap catalysts, which could be good candidates for high temperature LNT applications.« less

Ultrafast and Stable CO2 Capture Using Alkali Metal Salt-Promoted MgO-CaCO3 Sorbents.

PubMed

Cui, Hongjie; Zhang, Qiming; Hu, Yuanwu; Peng, Chong; Fang, Xiangchen; Cheng, Zhenmin; Galvita, Vladimir V; Zhou, Zhiming

2018-06-20

As a potential candidate for precombustion CO 2 capture at intermediate temperatures (200-400 °C), MgO-based sorbents usually suffer from low kinetics and poor cyclic stability. Herein, a general and facile approach is proposed for the fabrication of high-performance MgO-based sorbents via incorporation of CaCO 3 into MgO followed by deposition of a mixed alkali metal salt (AMS). The AMS-promoted MgO-CaCO 3 sorbents are capable of adsorbing CO 2 at an ultrafast rate, high capacity, and good stability. The CO 2 uptake of sorbent can reach as high as above 0.5 g CO 2 g sorbent -1 after only 5 min of sorption at 350 °C, accounting for vast majority of the total uptake. In addition, the sorbents are very stable even under severe but more realistic conditions (desorption in CO 2 at 500 °C), where the CO 2 uptake of the best sorbent is stabilized at 0.58 g CO 2 g sorbent -1 in 20 consecutive cycles. The excellent CO 2 capture performance of the sorbent is mainly due to the promoting effect of molten AMS, the rapid formation of CaMg(CO 3 ) 2 , and the plate-like structure of sorbent. The exceptional ultrafast rate and the good stability of the AMS-promoted MgO-CaCO 3 sorbents promise high potential for practical applications, such as precombustion CO 2 capture from integrated gasification combined cycle plants and sorption-enhanced water gas shift process.

Optical signature of Mg-doped GaN: Transfer processes

NASA Astrophysics Data System (ADS)

Callsen, G.; Wagner, M. R.; Kure, T.; Reparaz, J. S.; Bügler, M.; Brunnmeier, J.; Nenstiel, C.; Hoffmann, A.; Hoffmann, M.; Tweedie, J.; Bryan, Z.; Aygun, S.; Kirste, R.; Collazo, R.; Sitar, Z.

2012-08-01

Mg doping of high quality, metal organic chemical vapor deposition grown GaN films results in distinct traces in their photoluminescence and photoluminescence excitation spectra. We analyze GaN:Mg grown on sapphire substrates and identify two Mg related acceptor states, one additional acceptor state and three donor states that are involved in the donor-acceptor pair band transitions situated at 3.26-3.29 eV in GaN:Mg. The presented determination of the donor-acceptor pair band excitation channels by photoluminescence excitation spectroscopy in conjunction with temperature-dependent photoluminescence measurements results in a direct determination of the donor and acceptor binding, localization, and activation energies, which is put into a broader context based on Haynes's rule. Furthermore, we analyze the biexponential decay dynamics of the photoluminescence signal of the acceptor and donor bound excitons. As all observed lifetimes scale with the localization energy of the donor and acceptor related bound excitons, defect and complex bound excitons can be excluded as their origin. Detailed analysis of the exciton transfer processes in the close energetic vicinity of the GaN band edge reveals excitation via free and bound excitonic channels but also via an excited state as resolved for the deepest localized Mg related acceptor bound exciton. For the two Mg acceptor states, we determine binding energies of 164 ± 5 and 195 ± 5 meV, which is in good agreement with recent density functional theory results. This observation confirms and quantifies the general dual nature of acceptor states in GaN based on the presented analysis of the photoluminescence and photoluminescence excitation spectra.

Enhanced hydrogen generation by hydrolysis of Mg doped with flower-like MoS2 for fuel cell applications

NASA Astrophysics Data System (ADS)

Huang, Minghong; Ouyang, Liuzhang; Liu, Jiangwen; Wang, Hui; Shao, Huaiyu; Zhu, Min

2017-10-01

In this work, flower-like MoS2 spheres are synthesized via a hydrothermal method and the catalytic activity of the as-prepared and bulk MoS2 on hydrolysis of Mg is systematically investigated for the first time. The Mg-MoS2 composites are prepared by ball milling and the hydrogen generation performances of the composites are investigated in 3.5% NaCl solution. The experimental results suggest that the as-prepared MoS2 exhibits better catalytic effect on hydrolysis of Mg compared to bulk MoS2. In particular, Mg-10 wt% MoS2 (as-prepared) composite milled for 1 h shows the best hydrogen generation properties and releases 90.4% of theoretical hydrogen generation capacity within 1 min at room temperature. The excellent catalytic effect of as-prepared MoS2 may be attributed to the following aspects: three-dimensional flower-like MoS2 architectures improve its dispersibility on Mg particles; make the composite more reactive; hamper the generated Mg(OH)2 from adhering to the surface of Mg; and increase the galvanic corrosion of Mg. In addition, a hydrogen generator based on the hydrolysis reaction of Mg-0.2 wt% MoS2 composite is manufactured and it can supply a maximum hydrogen flow rate of 2.5 L/min. The findings here demonstrate the as-prepared flower-like MoS2 can be a promising catalyst for hydrogen generation from Mg.

Continuous real-time water-quality monitoring and regression analysis to compute constituent concentrations and loads in the North Fork Ninnescah River upstream from Cheney Reservoir, south-central Kansas, 1999–2012

USGS Publications Warehouse

Stone, Mandy L.; Graham, Jennifer L.; Gatotho, Jackline W.

2013-01-01

Cheney Reservoir, located in south-central Kansas, is the primary water supply for the city of Wichita. The U.S. Geological Survey has operated a continuous real-time water-quality monitoring station since 1998 on the North Fork Ninnescah River, the main source of inflow to Cheney Reservoir. Continuously measured water-quality physical properties include streamflow, specific conductance, pH, water temperature, dissolved oxygen, and turbidity. Discrete water-quality samples were collected during 1999 through 2009 and analyzed for sediment, nutrients, bacteria, and other water-quality constituents. Regression models were developed to establish relations between discretely sampled constituent concentrations and continuously measured physical properties to compute concentrations of those constituents of interest that are not easily measured in real time because of limitations in sensor technology and fiscal constraints. Regression models were published in 2006 that were based on data collected during 1997 through 2003. This report updates those models using discrete and continuous data collected during January 1999 through December 2009. Models also were developed for four new constituents, including additional nutrient species and indicator bacteria. In addition, a conversion factor of 0.68 was established to convert the Yellow Springs Instruments (YSI) model 6026 turbidity sensor measurements to the newer YSI model 6136 sensor at the North Ninnescah River upstream from Cheney Reservoir site. Newly developed models and 14 years of hourly continuously measured data were used to calculate selected constituent concentrations and loads during January 1999 through December 2012. The water-quality information in this report is important to the city of Wichita because it allows the concentrations of many potential pollutants of interest to Cheney Reservoir, including nutrients and sediment, to be estimated in real time and characterized over conditions and time scales that would not be possible otherwise. In general, model forms and the amount of variance explained by the models was similar between the original and updated models. The amount of variance explained by the updated models changed by 10 percent or less relative to the original models. Total nitrogen, nitrate, organic nitrogen, E. coli bacteria, and total organic carbon models were newly developed for this report. Additional data collection over a wider range of hydrological conditions facilitated the development of these models. The nitrate model is particularly important because it allows for comparison to Cheney Reservoir Task Force goals. Mean hourly computed total suspended solids concentration during 1999 through 2012 was 54 milligrams per liter (mg/L). The total suspended solids load during 1999 through 2012 was 174,031 tons. On an average annual basis, the Cheney Reservoir Task Force runoff (550 mg/L) and long-term (100 mg/L) total suspended solids goals were never exceeded, but the base flow goal was exceeded every year during 1999 through 2012. Mean hourly computed nitrate concentration was 1.08 mg/L during 1999 through 2012. The total nitrate load during 1999 through 2012 was 1,361 tons. On an annual average basis, the Cheney Reservoir Task Force runoff (6.60 mg/L) nitrate goal was never exceeded, the long-term goal (1.20 mg/L) was exceeded only in 2012, and the base flow goal of 0.25 mg/L was exceeded every year. Mean nitrate concentrations that were higher during base flow, rather than during runoff conditions, suggest that groundwater sources are the main contributors of nitrate to the North Fork Ninnescah River above Cheney Reservoir. Mean hourly computed phosphorus concentration was 0.14 mg/L during 1999 through 2012. The total phosphorus load during 1999 through 2012 was 328 tons. On an average annual basis, the Cheney Reservoir Task Force runoff goal of 0.40 mg/L for total phosphorus was exceeded in 2002, the year with the largest yearly mean turbidity, and the long-term goal (0.10 mg/L) was exceeded in every year except 2011 and 2012, the years with the smallest mean streamflows. The total phosphorus base flow goal of 0.05 mg/L was exceeded every year. Given that base flow goals for total suspended solids, nitrate, and total phosphorus were exceeded every year despite hydrologic conditions, the established base flow goals are either unattainable or substantially more best management practices will need to be implemented to attain them. On an annual average basis, no discernible patterns were evident in total suspended sediment, nitrate, and total phosphorus concentrations or loads over time, in large part because of hydrologic variability. However, more rigorous statistical analyses are required to evaluate temporal trends. A more rigorous analysis of temporal trends will allow evaluation of watershed investments in best management practices.

Efficacy of Additional Canagliflozin Administration to Type 2 Diabetes Patients Receiving Insulin Therapy: Examination of Diurnal Glycemic Patterns Using Continuous Glucose Monitoring (CGM).

PubMed

Matsumura, Mihoko; Nakatani, Yuki; Tanka, Seiichi; Aoki, Chie; Sagara, Masaaki; Yanagi, Kazunori; Suzuki, Kunihiro; Aso, Yoshimasa

2017-08-01

The efficacy of administering a sodium-glucose cotransporter 2 inhibitor during insulin therapy has not been established. In this study, we examined its effects based on diurnal glycemic patterns using continuous glucose monitoring (CGM). The subjects were 15 patients who had received insulin therapy for 1 year or more. A CGM device was attached to all subjects for 1 week. The administration of canagliflozin at 100 mg was started 4 days after attachment. The mean glucose concentrations, standard deviation (SD), mean amplitude of glycemic excursions (MAGE), mean of daily difference of blood glucose (MODD), and area under the curve (AUC) (≥180, <70 mg h/dL) after the start of administration were compared with the pretreatment values. In addition, we compared changes in the number of insulin units between basal and bolus insulin. Furthermore, we investigated the influence of canagliflozin on oxidative stress markers and cytokines using 8-hydroxy-2'-deoxyguanosine (8-OHdG), tumor necrosis factor-α (TNF-α), and adiponectin as parameters. The mean glucose concentrations decreased from 161.1 to 139.1 mg/dL (P < 0.01). The SD decreased from 36.5 to 29.6 mg/dL (P = 0.05). The MAGE decreased from 89.2 to 77.4 mg/dL (P < 0.01), and the MODD decreased from 34.3 to 25.5 mg/dL (P < 0.05). All parameters showed significant improvements in diurnal changes. AUC of ≥180, i.e., the total area of blood glucose levels at or above 180 on the blood glucose curve of CGM, decreased from 339.1 to 113.6 mg/dL (P < 0.05). AUC of <70, i.e., the total area of blood glucose levels below 70 on the blood glucose curve of CGM, slightly decreased from 1.6 to 0.3 mg/dL (P = 0.08). The total number of basal insulin units decreased from 128 to 76, and that of bolus insulin decreased from 266 to 154; the dose of insulin could be markedly decreased. In addition, the mean 8-OHdG level decreased from 11.4 to 10.8 ng/mg Cre (P < 0.05), and the mean TNF-α level decreased from 2.31 to 1.79 pg/mL (P = 0.10). The mean adiponectin level increased from 5.01 to 5.53 μg/mL (P < 0.05). Canagliflozin improved blood glucose changes in type 2 diabetes using insulin. In addition, the results suggest its antioxidant actions. University Hospital Medical Information Network (UMIN no. 000019429).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graham, Kenneth R.; Mei, Jianguo; Stalder, Romain

The effect of the macromolecular additive, polydimethylsiloxane (PDMS), on the performance of solution processed molecular bulk heterojunction solar cells is investigated, and the addition of PDMS is shown to improve device power conversion efficiency by ~70% and significantly reduce cell-to-cell variation, from a power conversion efficiency of 1.25 ± 0.37% with no PDMS to 2.16 ± 0.09% upon the addition of 0.1 mg/mL PDMS to the casting solution. The cells are based on a thiophene and isoindigo containing oligomer as the electron donor and [6,6]-phenyl-C61 butyric acid methyl ester (PC 61BM) as the electron acceptor. PDMS is shown to havemore » a strong influence on film morphology, with a significant decrease in film roughness and feature size observed. The morphology change leads to improved performance parameters, most notably an increase in the short circuit current density from 4.3 to 6.8 mA/cm 2 upon addition of 0.1 mg/mL PDMS. The use of PDMS is of particular interest, as this additive appears frequently as a lubricant in plastic syringes commonly used in device fabrication; therefore, PDMS may unintentionally be incorporated into device active layers.« less

In vitro corrosion and cytocompatibility properties of nano-whisker hydroxyapatite coating on magnesium alloy for bone tissue engineering applications.

PubMed

Yang, Huawei; Yan, Xueyu; Ling, Min; Xiong, Zuquan; Ou, Caiwen; Lu, Wei

2015-03-17

We report here the successful fabrication of nano-whisker hydroxyapatite (nHA) coatings on Mg alloy by using a simple one-step hydrothermal process in aqueous solution. The nHA coating shows uniform structure and high crystallinity. Results indicate that nHA coating is promising for improving the in vitro corrosion and cytocompatibility properties of Mg-based implants and devices for bone tissue engineering. In addition, the simple hydrothermal deposition method used in the current study is also applicable to substrates with complex shapes or surface geometries.

In Vitro Corrosion and Cytocompatibility Properties of Nano-Whisker Hydroxyapatite Coating on Magnesium Alloy for Bone Tissue Engineering Applications

PubMed Central

Yang, Huawei; Yan, Xueyu; Ling, Min; Xiong, Zuquan; Ou, Caiwen; Lu, Wei

2015-01-01

We report here the successful fabrication of nano-whisker hydroxyapatite (nHA) coatings on Mg alloy by using a simple one-step hydrothermal process in aqueous solution. The nHA coating shows uniform structure and high crystallinity. Results indicate that nHA coating is promising for improving the in vitro corrosion and cytocompatibility properties of Mg-based implants and devices for bone tissue engineering. In addition, the simple hydrothermal deposition method used in the current study is also applicable to substrates with complex shapes or surface geometries. PMID:25789500

Comparison of effect of an increased dosage of vonoprazan versus vonoprazan plus lafutidine on gastric acid inhibition and serum gastrin.

PubMed

Suzuki, Takahiro; Kagami, Takuma; Uotani, Takahiro; Yamade, Mihoko; Hamaya, Yasushi; Iwaizumi, Moriya; Osawa, Satoshi; Sugimoto, Ken; Miyajima, Hiroaki; Furuta, Takahisa

2018-01-01

Vonoprazan, a novel potassium-competitive acid blocker, elicits potent acid inhibition and hypergastrinemia at a dose of 20 mg. Its recommended maintenance dose for gastro-esophageal reflux disease is 10 mg, which is sometimes insufficient for preventing nocturnal acid breakthrough (NAB). Concomitant use of a histamine 2 receptor antagonist (H 2 RA) is effective for NAB. However, further acid inhibition by addition of H2RA has concern of hypergastrinemia again. Lafutidine (H2RA) is known to stimulate somatostatin release. The aim of this study is to compare the levels of acid inhibition and serum gastrin attained by addition of lafutidine to vonoprazan 10 mg with levels after a dose increase of vonoprazan from 10 to 20 mg. Thirteen healthy volunteers underwent 24-h intragastric pH monitoring and serum gastrin measurements on day 7 of three different regimens: vonoprazan 10 mg, vonoprazan 10 mg plus lafutidine 10 mg, and vonoprazan 20 mg. Median pH 4 holding time ratios (range) by vonoprazan 10 mg, vonoprazan 10 mg plus lafutidine 10 mg, and vonoprazan 20 mg were 82% (47-88%), 88% (76-93%), and 99% (95-100%) while those at nighttime from 10 p.m. to 8 a.m. were 94% (29-100%), 100% (95-100%), and 100%, respectively. The incidences of NAB with vonoprazan 10 mg, vonoprazan plus lafutidine, and vonoprazan 20 mg were 38, 8, and 0%, respectively. Respective serum gastrin levels were 420 (173-508), 323 (196-521), and 504 (400-812) pg/ml. Addition of lafutidine 10 mg to vonoprazan 10 mg achieved sufficient acid inhibition, especially at nighttime, without further increase of serum gastrin levels.

The tissue residues of sodium dehydroacetate used as feed preservative in swine.

PubMed

Liu, Hao; Han, Lingling; Xie, Jiayu; Wu, Yingchao; Xie, Yang; Zhang, Yumei

2018-01-01

Sodium dehydroacetate (Na-DHA) is a food and feed additive with antimicrobial effects. There is little information on Na-DHA residue levels in foods derived from animals. In this study, Na-DHA residue levels in swine tissues were determined by HLPC, and the pharmacokinetics of Na-DHA in tissues were determined. The Na-DHA residue levels in swine tissues were <1.2 mg kg -1 at different withdrawal time after thirty-two Duroc × Landrace × Yorkshire pigs were administered 200 mg Na-DHA kg -1 through the feed for 30 days. In decreasing order of Na-DHA residue levels, the tissues were kidney > liver > muscle > fat. The pharmacokinetics of Na-DHA followed a binomial regression model, and the half-time of Na-DHA in swine tissues was 9.07 days for kidney, 7.19 days for liver, 6.66 days for muscle, and 5.39 days for fat tissue. The accuracy of the HPLC method for Na-DHA determination ranged from 80.18% to 91.33% recovery, with coefficients of variation <6.4%, limit of detection of 0.08 mg kg -1 , and limit of quantification of 0.2 mg kg -1 . Na-DHA included at 200 mg kg -1 in a swine diet is a safe feed additive based on residue elimination and ADI values reported. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

A study of advanced magnesium-based hydride and development of a metal hydride thermal battery system

NASA Astrophysics Data System (ADS)

Zhou, Chengshang

Metal hydrides are a group of important materials known as energy carriers for renewable energy and thermal energy storage. A concept of thermal battery based on advanced metal hydrides is studied for heating and cooling of cabins in electric vehicles. The system utilizes a pair of thermodynamically matched metal hydrides as energy storage media. The hot hydride that is identified and developed is catalyzed MgH2 due to its high energy density and enhanced kinetics. TiV0.62Mn1.5, TiMn2, and LaNi5 alloys are selected as the matching cold hydride. A systematic experimental survey is carried out in this study to compare a wide range of additives including transitions metals, transition metal oxides, hydrides, intermetallic compounds, and carbon materials, with respect to their effects on dehydrogenation properties of MgH2. The results show that additives such as Ti and V-based metals, hydride, and certain intermetallic compounds have strong catalytic effects. Solid solution alloys of magnesium are exploited as a way to destabilize magnesium hydride thermodynamically. Various elements are alloyed with magnesium to form solid solutions, including indium and aluminum. Thermodynamic properties of the reactions between the magnesium solid solution alloys and hydrogen are investigated, showing that all the solid solution alloys that are investigated in this work have higher equilibrium hydrogen pressures than that of pure magnesium. Cyclic stability of catalyzed MgH2 is characterized and analyzed using a PCT Sievert-type apparatus. Three systems, including MgH2-TiH 2, MgH2-TiMn2, and MgH2-VTiCr, are examined. The hydrogenating and dehydrogenating kinetics at 300°C are stable after 100 cycles. However, the low temperature (25°C to 150°C) hydrogenation kinetics suffer a severe degradation during hydrogen cycling. Further experiments confirm that the low temperature kinetic degradation can be mainly related the extended hydrogenation-dehydrogenation reactions. Proof-of-concept prototypes are built and tested, demonstrating the potential of the system as HVAC for transportation vehicles. The performance of the concept-demonstration-unit show both high heating/cooling power and high energy densities. An extended cycling test shows degradation on the performance of the system. To solve this problem, a metal hydride hydrogen compressor is proposed for aiding the recharge process of the system.

First-principles studies of hydrogen interaction with ultrathin Mg and Mg-based alloy films

NASA Astrophysics Data System (ADS)

Yoon, Mina; Weitering, Hanno H.; Zhang, Zhenyu

2011-01-01

The search for technologically and economically viable storage solutions for hydrogen fuel would benefit greatly from research strategies that involve systematic property tuning of potential storage materials via atomic-level modification. Here, we use first-principles density-functional theory to investigate theoretically the structural and electronic properties of ultrathin Mg films and Mg-based alloy films and their interaction with atomic hydrogen. Additional delocalized charges are distributed over the Mg films upon alloying them with 11.1% of Al or Na atoms. These extra charges contribute to enhance the hydrogen binding strength to the films. We calculated the chemical potential of hydrogen in Mg films for different dopant species and film thickness, and we included the vibrational degrees of freedom. By comparing the chemical potential with that of free hydrogen gas at finite temperature (T) and pressure (P), we construct a hydrogenation phase diagram and identify the conditions for hydrogen absorption or desorption. The formation enthalpies of metal hydrides are greatly increased in thin films, and in stark contrast to its bulk phase, the hydride state can only be stabilized at high P and T (where the chemical potential of free H2 is very high). Metal doping increases the thermodynamic stabilities of the hydride films and thus significantly helps to reduce the required pressure condition for hydrogen absorption from H2 gas. In particular, with Na alloying, hydrogen can be absorbed and/or desorbed at experimentally accessible T and P conditions.

The toxicity of glyphosate alone and glyphosate-surfactant mixtures to western toad (Anaxyrus boreas) tadpoles.

PubMed

Vincent, Kim; Davidson, Carlos

2015-12-01

Pesticide choice based on toxicity to nontarget wildlife is reliant on available toxicity data. Despite a number of recent studies examining the effects of glyphosate on amphibians, very few have aimed to understand the toxicological effects of glyphosate in combination with surfactants as it is commonly applied in the field. Land managers interested in making pesticide choices based on minimizing impacts to nontarget wildlife are hindered by a lack of published toxicity data. Short-term acute toxicity trials were conducted for glyphosate in the form of isopropylamine salt (IPA) alone and mixed with 2 surfactants: Agri-dex and Competitor with western toad (Anaxyrus [Bufo] boreas) tadpoles. Glyphosate IPA mixed with Competitor was 6 times more toxic than glyphosate IPA mixed with Agri-dex, and both mixtures were more toxic than glyphosate IPA alone. The median lethal concentrations reported for 24-h and 48-h exposures were 8279 mg/L (24 h) and 6392 mg/L (48 h) for glyphosate IPA alone; 5092 mg/L (24 h) and 4254 mg/L (48 h) for glyphosate IPA mixed with Agri-dex; and 853 mg/L (24 h) and 711 mg/L (48 h) for glyphosate IPA mixed with Competitor. The present study indicates that the toxicity of a tank mix may be greatly increased by the addition of surfactants and may vary widely depending on the specific surfactant. © 2015 SETAC.

Mg2B2O5 Nanowire Enabled Multifunctional Solid-State Electrolytes with High Ionic Conductivity, Excellent Mechanical Properties, and Flame-Retardant Performance.

PubMed

Sheng, Ouwei; Jin, Chengbin; Luo, Jianmin; Yuan, Huadong; Huang, Hui; Gan, Yongping; Zhang, Jun; Xia, Yang; Liang, Chu; Zhang, Wenkui; Tao, Xinyong

2018-05-09

High ionic conductivity, satisfactory mechanical properties, and wide electrochemical windows are crucial factors for composite electrolytes employed in solid-state lithium-ion batteries (SSLIBs). Based on these considerations, we fabricate Mg 2 B 2 O 5 nanowire enabled poly(ethylene oxide) (PEO)-based solid-state electrolytes (SSEs). Notably, these SSEs have enhanced ionic conductivity and a large electrochemical window. The elevated ionic conductivity is attributed to the improved motion of PEO chains and the increased Li migrating pathway on the interface between Mg 2 B 2 O 5 and PEO-LiTFSI. Moreover, the interaction between Mg 2 B 2 O 5 and -SO 2 - in TFSI - anions could also benefit the improvement of conductivity. In addition, the SSEs containing Mg 2 B 2 O 5 nanowires exhibit improved the mechanical properties and flame-retardant performance, which are all superior to the pristine PEO-LiTFSI electrolyte. When these multifunctional SSEs are paired with LiFePO 4 cathodes and lithium metal anodes, the SSLIBs show better rate performance and higher cyclic capacity of 150, 106, and 50 mAh g -1 under 0.2 C at 50, 40, and 30 °C. This strategy of employing Mg 2 B 2 O 5 nanowires provides the design guidelines of assembling multifunctional SSLIBs with high ionic conductivity, excellent mechanical properties, and flame-retardant performance at the same time.

Thermodynamics, kinetics, and catalytic effect of dehydrogenation from MgH2 stepped surfaces and nanocluster: a DFT study

NASA Astrophysics Data System (ADS)

Reich, Jason; Wang, Linlin; Johnson, Duane

2013-03-01

We detail the results of a Density Functional Theory (DFT) based study of hydrogen desorption, including thermodynamics and kinetics with(out) catalytic dopants, on stepped (110) rutile and nanocluster MgH2. We investigate competing configurations (optimal surface and nanoparticle configurations) using simulated annealing with additional converged results at 0 K, necessary for finding the low-energy, doped MgH2 nanostructures. Thermodynamics of hydrogen desorption from unique dopant sites will be shown, as well as activation energies using the Nudged Elastic Band algorithm. To compare to experiment, both stepped structures and nanoclusters are required to understanding and predict the effects of ball milling. We demonstrate how these model systems relate to the intermediary sized structures typically seen in ball milling experiments.

Cu2O-based solar cells using oxide semiconductors

NASA Astrophysics Data System (ADS)

Minami, Tadatsugu; Nishi, Yuki; Miyata, Toshihiro

2016-01-01

We describe significant improvements of the photovoltaic properties that were achieved in Al-doped ZnO (AZO)/n-type oxide semiconductor/p-type Cu2O heterojunction solar cells fabricated using p-type Cu2O sheets prepared by thermally oxidizing Cu sheets. The multicomponent oxide thin film used as the n-type semiconductor layer was prepared with various chemical compositions on non-intentionally heated Cu2O sheets under various deposition conditions using a pulsed laser deposition method. In Cu2O-based heterojunction solar cells fabricated using various ternary compounds as the n-type oxide thin-film layer, the best photovoltaic performance was obtained with an n-ZnGa2O4 thin-film layer. In most of the Cu2O-based heterojunction solar cells using multicomponent oxides composed of combinations of various binary compounds, the obtained photovoltaic properties changed gradually as the chemical composition was varied. However, with the ZnO-MgO and Ga2O3-Al2O3 systems, higher conversion efficiencies (η) as well as a high open circuit voltage (Voc) were obtained by using a relatively small amount of MgO or Al2O3, e.g., (ZnO)0.91-(MgO)0.09 and (Ga2O3)0.975-(Al2O3)0.025, respectively. When Cu2O-based heterojunction solar cells were fabricated using Al2O3-Ga2O3-MgO-ZnO (AGMZO) multicomponent oxide thin films deposited with metal atomic ratios of 10, 60, 10 and 20 at.% for the Al, Ga, Mg and Zn, respectively, a high Voc of 0.98 V and an η of 4.82% were obtained. In addition, an enhanced η and an improved fill factor could be achieved in AZO/n-type multicomponent oxide/p-type Cu2O heterojunction solar cells fabricated using Na-doped Cu2O (Cu2O:Na) sheets that featured a resistivity controlled by optimizing the post-annealing temperature and duration. Consequently, an η of 6.25% and a Voc of 0.84 V were obtained in a MgF2/AZO/n-(Ga2O3-Al2O3)/p-Cu2O:Na heterojunction solar cell fabricated using a Cu2O:Na sheet with a resistivity of approximately 10 Ω·cm and a (Ga0.975Al0.025)2O3 thin film with a thickness of approximately 60 nm. In addition, a Voc of 0.96 V and an η of 5.4% were obtained in a MgF2/AZO/n-AGMZO/p-Cu2O:Na heterojunction solar cell.

The effects of water replacement by oral rehydration fluids with or without betaine supplementation on performance, acid-base balance, and water retention of heat-stressed broiler chickens.

PubMed

Sayed, M A M; Downing, J

2011-01-01

Exposing broilers to a high temperature increases water and electrolyte K(+) and Na(+) excretion, which negatively affects the heat dissipation capacity and acid-base homeostasis, resulting in losses in growth performance. In this experiment, the efficacy of providing oral rehydration therapy and betaine on growth performance, acid-base balance, and water and electrolyte retention was evaluated. A total of 432 one-day-old broiler chicks (Cobb) were allocated to 72 metabolic cages and reared to 31 d of age under standard conditions. From 32 to 41 d of age, chicks were exposed to heat stress (ambient temperature, 32°C) and high RH (80 to 100% RH) for 9 h daily. The ameliorative effects of a 3 × 3 factorial array of treatments administered via drinking water were evaluated in 8 replicates of 6 chicks per cage for each treatment. Two oral rehydration therapy (ORT) fluids, based on either citrate or bicarbonate salts, were added to tap water. In addition, betaine was added to tap water at an inclusion rate of 0, 500, or 1,000 mg/L to complete the array of 9 liquid-based treatments. Growth performance was assessed at 32, 35, and 41 d of age. From 32 to 35 d of age, chicks receiving ORT fluids exhibited improved growth performance, water balance, and electrolyte (K(+), Na(+)) retention. In addition, the physiological response to stress was attenuated, as indicated by lower heterophil-to-lymphocyte ratios and blood glucose concentrations relative to the negative controls. The addition of betaine at an inclusion rate of 500 mg/L improved BW gain. From d 36 to 41, treatments did not significantly influence growth performance, which suggests that chicks receiving tap water were able to compensate and adapt to the heat-stress conditions. The results demonstrate that the beneficial effects of providing ORT fluids and 500 mg of betaine/L were observed only during the first 4 d of heat exposure. After this period, adaptation to the heat appears to occur, and none of the treatments was successful in improving growth performance.

Ultraviolet photodetector based on Mg{sub x}Zn{sub 1-x}O films using plasma-enhanced atomic layer deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Yu-Chang; Lee, Hsin-Ying, E-mail: hylee@ee.ncku.edu.tw; Lee, Ching-Ting

2016-01-15

A plasma-enhanced atomic layer deposition (PE-ALD) system was used to deposit magnesium zinc oxide (Mg{sub x}Zn{sub 1−x}O) films with various Mg content (x). The Mg{sub x}Zn{sub 1-x}O films were applied to metal–semiconductor–metal ultraviolet (UV) photodetectors (MSM-UPDs) as an active layer. The Mg content in the Mg{sub x}Zn{sub 1-x}O films was modulated by adjusting the ZnO–MgO cycle ratios to 15:1, 12:1, and 9:1. Correspondingly, the Mg content in the Mg{sub x}Zn{sub 1-x}O films characterized using an energy dispersive spectrometer was 0.10, 0.13, and 0.16, respectively. The optical bandgap of the Mg{sub x}Zn{sub 1-x}O films increased from 3.56 to 3.66 eV withmore » an increase in Mg content from 0.10 to 0.16. The peak position of photoresponsivity for the Mg{sub x}Zn{sub 1-x}O MSM-UPDs was also shifted from 350 to 340 nm. The UV-visible rejection ratios of the Mg{sub x}Zn{sub 1-x}O MSM-UPDs were higher than 3 orders of magnitude. In addition, excellent detectivity and noise equivalent power for the Mg{sub x}Zn{sub 1-x}O MSM-UPDs were observed at a bias voltage of 5 V. The high performance of the Mg{sub x}Zn{sub 1-x}O MSM-UPDs was achieved by PE-ALD at a low temperature.« less

Arsenic removal with iron(II) and iron(III) in waters with high silicate and phosphate concentrations.

PubMed

Roberts, Linda C; Hug, Stephan J; Ruettimann, Thomas; Billah, Morsaline; Khan, Abdul Wahab; Rahman, Mohammad Tariqur

2004-01-01

Arsenic removal by passive treatment, in which naturally present Fe(II) is oxidized by aeration and the forming iron(III) (hydr)oxides precipitate with adsorbed arsenic, is the simplest conceivable water treatment option. However, competing anions and low iron concentrations often require additional iron. Application of Fe(II) instead of the usually applied Fe(III) is shown to be advantageous, as oxidation of Fe(II) by dissolved oxygen causes partial oxidation of As(III) and iron(III) (hydr)oxides formed from Fe(II) have higher sorption capacities. In simulated groundwater (8.2 mM HCO3(-), 2.5 mM Ca2+, 1.6 mM Mg2+, 30 mg/L Si, 3 mg/L P, 500 ppb As(III), or As(V), pH 7.0 +/- 0.1), addition of Fe(II) clearly leads to better As removal than Fe(III). Multiple additions of Fe(II) further improved the removal of As(II). A competitive coprecipitation model that considers As(III) oxidation explains the observed results and allows the estimation of arsenic removal under different conditions. Lowering 500 microg/L As(III) to below 50 microg/L As(tot) in filtered water required > 80 mg/L Fe(III), 50-55 mg/L Fe(II) in one single addition, and 20-25 mg/L in multiple additions. With As(V), 10-12 mg/L Fe(II) and 15-18 mg/L Fe(III) was required. In the absence of Si and P, removal efficiencies for Fe(II) and Fe(III) were similar: 30-40 mg/L was required for As(II), and 2.0-2.5 mg/L was required for As(V). In a field study with 22 tubewells in Bangladesh, passive treatment efficiently removed phosphate, but iron contents were generally too low for efficient arsenic removal.

A phase I/pharmacokinetic study of sunitinib in combination with highly active antiretroviral therapy (HAART) in HIV-positive patients with cancer: AIDS Malignancy Consortium Trial AMC 061

PubMed Central

Rudek, Michelle A; Moore, Page C.; Mitsuyasu, Ronald T.; Dezube, Bruce J.; Aboulafia, David; Gerecitano, John; Sullivan, Ryan; Cianfrocca, Mary E.; Henry, David H.; Ratner, Lee; Haigentz, Missak; Dowlati, Afshin; Little, Richard F.; Ivy, S. Percy; Deeken, John F.

2014-01-01

Background Treatment of non-AIDS defining cancers (NADCs) may be complicated by drug interactions between highly active antiretroviral therapy (HAART) and chemotherapy. This trial is the first by the AIDS Malignancy Consortium assessing targeted therapies and HAART in HIV+ cancer patients (ClinicalTrials.gov NCT00890747). Methods Patients were stratified into two arms based on whether they were taking ritonavir, a potent CYP3A4 inhibitor, in a modified phase I study of sunitinib. Patients in arm 1 (non-ritonavir HAART) received standard sunitinib dosing (50mg/day). Arm 2 (ritonavir-based HAART) used a phase I, 3+3 dose escalation design (from 25 to 50mg/day). Cycles were with four weeks on treatment followed by a two week break (6 weeks total). Pharmacokinetics of sunitinib and its active metabolite (N-desethyl sunitinib) were assessed. Results Nineteen patients were enrolled and evaluable. Patients on Arm 1 tolerated treatment with one observed dose limiting toxicity (DLT). In Arm 2, a DLT was experienced at 37.5mg, and an additional 3 of 5 patients experienced grade 3 neutropenia, an uncommon toxicity of sunitinib. No patient had a response, but 10 had stable disease, including 8 with prolonged disease stability. Efavirenz, a potent inducer of CYP3A4, resulted in increased exposure of N-desethyl sunitinib, whereas ritonavir caused decreased exposure of the metabolite. Hand-foot syndrome was associated with higher steady-state trough concentrations of sunitinib. Conclusions Patients on non-ritonavir based HAART regimens tolerated standard dosing of sunitinib. Patients on ritonavir-based therapy treated with 37.5mg/day experienced higher toxicities. Dose reduction of sunitinib to 37.5mg may be warranted in patients on ritonavir. PMID:24474568

Influence of copper composition on mechanical properties of biodegradable material Mg-Zn-Cu for orthopedic application

NASA Astrophysics Data System (ADS)

Purniawan, A.; Maulidiah, H. M.; Purwaningsih, H.

2018-04-01

Implant is usually used as a treatment of bone fracture. At the moment, non-biodegradable implants is still widely employed in this application. Non-biodegradable implant requires re-surgery to retrieve implants that are installed in the body. It increase the cost and it is painful for the patient itself. In order to solve the problem, Mg-based biodegradable metals is developing so that the material will be compatible with body and gradually degrade in patient's body. However, magnesium has several disadvantages such as high degradation rates and low mechanical properties when compared to the mechanical properties of natural bone. Therefore, it is necessary to add elements into the magnesium alloy. In this research, copper (Cu) was alloyed in Mg alloy based biodegradable material. In addition, Cu is not only strengthening the structure but also for supporting element for the immune system, antibacterial and antifungal. The purpose of this research is to improve mechanical properties of Mg-based biodegradable material using Cu alloying. Powder metallurgy method was used to fabricate the device. The variation used in this research is the composition of Cu (0.5, 1, and 1.5% Cu). The porosity test was performed using apparent porosity test, compressive test and hardness test to know the mechanical properties of the alloy, and the weightless test to find out the material degradation rate. Based on the results can be conclude that Mg-Zn-Cu alloy material with 1% Cu composition is the most suitable specimen to be applied as a candidate for orthopedic devices material with hardness value is 393.6 MPa. Also obtained the value of the compressive test is 153 MPa.

Myasthenia Gravis: Tests and Diagnostic Methods

MedlinePlus

... Focus on MG Newsletter MG Quarterly Test & Diagnostic methods In addition to a complete medical and neurological ... How can I help? About MGFA Test & Diagnostic methods Treatment for MG FAQ's Upcoming Events 2018 MG ...

Safety and efficacy of once-weekly semaglutide vs additional oral antidiabetic drugs in Japanese people with inadequately controlled type 2 diabetes: A randomized trial.

PubMed

Kaku, Kohei; Yamada, Yuichiro; Watada, Hirotaka; Abiko, Atsuko; Nishida, Tomoyuki; Zacho, Jeppe; Kiyosue, Arihiro

2018-05-01

To evaluate the safety and efficacy of once-weekly subcutaneous semaglutide as monotherapy or combined with an oral antidiabetic drug (OAD) vs an additional OAD added to background therapy in Japanese people with type 2 diabetes (T2D) inadequately controlled on diet/exercise or OAD monotherapy. In this phase III, open-label trial, adults with T2D were randomized 2:2:1 to semaglutide 0.5 mg or 1.0 mg, or one additional OAD (a dipeptidyl peptidase-4 inhibitor, biguanide, sulphonylurea, glinide, α-glucosidase inhibitor or thiazolidinedione) with a different mode of action from that of background therapy. The primary endpoint was number of adverse events (AEs) after 56 weeks. Baseline characteristics were balanced between treatment arms (601 randomized). More AEs were reported in the semaglutide 0.5 mg (86.2%) and 1.0 mg (88.0%) groups than in the additional OAD group (71.7%). These were typically mild/moderate. Gastrointestinal AEs were most frequent with semaglutide, which diminished over time. The mean glycated haemoglobin (HbA1c) concentration (baseline 8.1%) was significantly reduced with semaglutide 0.5 mg and 1.0 mg vs additional OAD (1.7% and 2.0% vs 0.7%, respectively; estimated treatment difference [ETD] vs additional OAD -1.08% and -1.37%, both P < .0001). Body weight (baseline 71.5 kg) was reduced by 1.4 kg and 3.2 kg with semaglutide 0.5 mg and 1.0 mg, vs a 0.4-kg increase with additional OAD (ETD -1.84 kg and -3.59 kg; both P < .0001). For semaglutide-treated participants, >80% achieved an HbA1c concentration <7.0% (Japanese Diabetes Society target). Semaglutide was well tolerated, with no new safety issues identified. Semaglutide treatment significantly reduced HbA1c and body weight vs additional OAD treatment in Japanese people with T2D. © 2018 The Authors. Diabetes, Obesity and Metabolism published by John Wiley & Sons Ltd.

Enhanced production of acarbose and concurrently reduced formation of impurity c by addition of validamine in fermentation of Actinoplanes utahensis ZJB-08196.

PubMed

Xue, Ya-Ping; Qin, Jun-Wei; Wang, Ya-Jun; Wang, Yuan-Shan; Zheng, Yu-Guo

2013-01-01

Commercial production of acarbose is exclusively via done microbial fermentation with strains from the genera of Actinoplanes. The addition of C7N-aminocyclitols for enhanced production of acarbose and concurrently reduced formation of impurity C by cultivation of A. utahensis ZJB-08196 in 500-mL shake flasks was investigated, and validamine was found to be the most effective strategy. Under the optimal conditions of validamine addition, acarbose titer was increased from 3560 ± 128 mg/L to 4950 ± 156 mg/L, and impurity C concentration was concurrently decreased from 289 ± 24 mg/L to 107 ± 29 mg/L in batch fermentation after 168 h of cultivation. A further fed-batch experiment coupled with the addition of validamine (20 mg/L) in the fermentation medium prior to inoculation was designed to enhance the production of acarbose. When twice feedings of a mixture of 6 g/L glucose, 14 g/L maltose, and 9 g/L soybean flour were performed at 72 h and 96 h, acarbose titer reached 6606 ± 103 mg/L and impurity C concentration was only 212 ± 12 mg/L at 168 h of cultivation. Acarbose titer and proportion of acarbose/impurity C increased by 85.6% and 152.9% when compared with control experiments. This work demonstrates for the first time that validamine addition is a simple and effective strategy for increasing acarbose production and reducing impurity C formation.

Usefulness of addition of Orvus ES paste and sodium lauryl sulfate to frozen feline semen.

PubMed

Mizutani, Tatsuji; Sumigama, Shiho; Nagakubo, Keiichi; Shimizu, Noriko; Oba, Hiromichi; Hori, Tatsuya; Tsutsui, Toshihiko

2010-01-01

It has been shown that addition of the surfactant Orvus ES paste (OEP) and its main component sodium lauryl sulfate (SLS) to boar or dog semen before freezing improves post-thaw sperm motility and protects acrosome caps. In this study, we investigated the usefulness of the addition of OEP (0, 1, 2 and 4%) or SLS (0, 1, 2, 3 and 4 mg/ml) to cat ejaculates before freezing and their concentrations. Among the OEP addition groups, the 1% OEP group showed higher sperm motility than the other groups. Among the SLS addition groups, the 3 mg/ml SLS group showed slightly higher sperm motility and viability than the other groups. Comparison between the 1% OEP and 3 mg/ml SLS addition groups suggested a higher percentage of sperm with an acrosome cap in the 1% OEP group. The other sperm properties did not significantly differ between the 2 groups. These results indicate that addition of 1% OEP or 3 mg/ml SLS is effective for freezing of cat ejaculated semen.

An Evaluation of Alternatives to Nitrites and Sulfites to Inhibit the Growth of Salmonella enterica and Listeria monocytogenes in Meat Products

PubMed Central

Lamas, Alexandre; Miranda, José Manuel; Vázquez, Beatriz; Cepeda, Alberto; Franco, Carlos Manuel

2016-01-01

In recent years, the use of nitrites and sulfites as food preservatives has been a cause for concern due to the health problems that these additives can cause in humans. Natural products have been studied as an alternative, but most of them have hardly been applied in the food industry for technological and economic reasons. In this sense, organic salts such as sodium acetate are a good alternative due to their affordability. Thus, this study evaluated the capacity of sodium nitrite, sodium sulfite, a sodium acetate product (TQI C-6000), and chitosan to inhibit two important foodborne pathogens, Salmonella enterica and Listeria monocytogenes. The MIC of each chemical was in vitro evaluated and their antibacterial action was subsequently checked in situ using minced meat as a food model. MIC values of sodium nitrite (10,000 mg/L) and sodium sulfite (50,000 mg/L) for Salmonella enterica were higher than the values allowed by legislation (450 mg/L for sulfites and 150 mg/L for nitrites). Additionally, the sodium acetate product caused the inhibition of Salmonella enterica and Listeria at a relative low quantity. The two foodborne pathogens were inhibited in the food model with 1% of the sodium acetate product. Additionally, there were no significant differences between sodium nitrite, sodium sulfite, and sodium acetate products in the inhibition of Salmonella enterica and Listeria monocytogenes in the food model. Thus, products based on sodium acetate can be an alternative to traditional preservatives in food products. PMID:28231169

An Evaluation of Alternatives to Nitrites and Sulfites to Inhibit the Growth of Salmonella enterica and Listeria monocytogenes in Meat Products.

PubMed

Lamas, Alexandre; Miranda, José Manuel; Vázquez, Beatriz; Cepeda, Alberto; Franco, Carlos Manuel

2016-10-31

In recent years, the use of nitrites and sulfites as food preservatives has been a cause for concern due to the health problems that these additives can cause in humans. Natural products have been studied as an alternative, but most of them have hardly been applied in the food industry for technological and economic reasons. In this sense, organic salts such as sodium acetate are a good alternative due to their affordability. Thus, this study evaluated the capacity of sodium nitrite, sodium sulfite, a sodium acetate product (TQI C-6000), and chitosan to inhibit two important foodborne pathogens, Salmonella enterica and Listeria monocytogenes . The MIC of each chemical was in vitro evaluated and their antibacterial action was subsequently checked in situ using minced meat as a food model. MIC values of sodium nitrite (10,000 mg/L) and sodium sulfite (50,000 mg/L) for Salmonella enterica were higher than the values allowed by legislation (450 mg/L for sulfites and 150 mg/L for nitrites). Additionally, the sodium acetate product caused the inhibition of Salmonella enterica and Listeria at a relative low quantity. The two foodborne pathogens were inhibited in the food model with 1% of the sodium acetate product. Additionally, there were no significant differences between sodium nitrite, sodium sulfite, and sodium acetate products in the inhibition of Salmonella enterica and Listeria monocytogenes in the food model. Thus, products based on sodium acetate can be an alternative to traditional preservatives in food products.

Magnesium Alleviates Adverse Effects of Lead on Growth, Photosynthesis, and Ultrastructural Alterations of Torreya grandis Seedlings.

PubMed

Shen, Jie; Song, Lili; Müller, Karin; Hu, Yuanyuan; Song, Yang; Yu, Weiwu; Wang, Hailong; Wu, Jiasheng

2016-01-01

Magnesium (Mg 2+ ) has been shown to reduce the physiological and biochemical stress in plants caused by heavy metals. To date our understanding of how Mg 2+ ameliorates the adverse effects of heavy metals in plants is scarce. The potential effect of Mg 2+ on lead (Pb 2+ ) toxicity in plants has not yet been studied. This study was designed to clarify the mechanism of Mg 2+ -induced alleviation of lead (Pb 2+ ) toxicity. Torreya grandis ( T. grandis ) seedlings were grown in substrate contaminated with 0, 700 and 1400 mg Pb 2+ per kg -1 and with or without the addition of 1040 mg kg -1 Mg 2+ . Growth parameters, concentrations of Pb 2+ and Mg 2+ in the plants' shoots and roots, photosynthetic pigment, gas exchange parameters, the maximum quantum efficiency (Fv/Fm), root oxidative activity, ultrastructure of chloroplasts and root growth were determined to analyze the effect of different Pb 2+ concentrations on the seedlings as well as the potential ameliorating effect of Mg 2+ on the Pb 2+ induced toxicity. All measurements were tested by a one-way ANOVA for the effects of treatments. The growth of T. grandis seedlings cultivated in soils treated with 1400 mg kg -1 Pb 2+ was significantly reduced compared with that of plants cultivated in soils treated with 0 or 700 mg kg -1 Pb 2+ . The addition of 1040 mg kg -1 Mg 2+ improved the growth of the Pb 2+ -stressed seedlings, which was accompanied by increased chlorophyll content, the net photosynthetic rate and Fv/Fm, and enhanced chloroplasts development. In addition, the application of Mg 2+ induced plants to accumulate five times higher concentrations of Pb 2+ in the roots and to absorb and translocate four times higher concentrations of Mg 2+ to the shoots than those without Mg 2+ application. Furthermore, Mg 2+ addition increased root growth and oxidative activity, and protected the root ultrastructure. To the best of our knowledge, our study is the first report on the mechanism of Mg 2+ -induced alleviation of Pb 2+ toxicity. The generated results may have important implications for understanding the physiological interactions between heavy metals and plants, and for successful management of T. grandis plantations grown on soils contaminated with Pb 2+ .

Enhanced hydrogen sorption kinetics of Mg 50Ni-LiBH 4 composite by CeCl 3 addition

NASA Astrophysics Data System (ADS)

Gennari, F. C.; Puszkiel, J. A.

Mg 50Ni-LiBH 4 and Mg 50Ni-LiBH 4-CeCl 3 composites have been prepared by short times of ball milling under argon atmosphere. Combination of HP-DSC and volumetric techniques show that Mg 50Ni-LiBH 4-CeCl 3 composite not only uptakes hydrogen faster than Mg 50Ni-LiBH 4, but also releases hydrogen at a lower temperature (225 °C). The presence of CeCl 3 has a catalytic role, but it does not modify the thermodynamic properties of the composite which corresponds to MgH 2. Experimental studies on the hydriding/dehydriding mechanisms demonstrate that LiBH 4 and Ni lead to the formation of MgNi 3B 2 in both composites. In addition, XRD/DSC analysis and thermodynamic calculations demonstrate that the addition of CeCl 3 accounts for the enhancement of the hydrogen absorption/desorption kinetics through the interaction with LiBH 4. The in situ formation and subsequent decomposition of Ce(BH 4) 3 provides a uniform distribution of nanosize CeB 4 compound, which plays an important role in improving the kinetic properties of MgH 2.

Polyamine replacement by magnesium ions in BHK-21/C13 cells

PubMed Central

Melvin, Maureen A. L.; Keir, Hamish M.

1979-01-01

Cultures of BHK-21/C13 cells, whose growth was inhibited by deprivation of serum, were stimulated to grow by addition of serum to the culture medium. Addition of MgCl2 to the medium, to increase the concentration of Mg2+ ions by 15mm, 30min before addition of serum, had no effect on the stimulation of cell growth, but inhibited the accumulation of cellular spermidine, so that the spermidine/spermine molar ratio was lower in these cultures than in cultures that had received no additional cations. The increase in the activity of ornithine decarboxylase that occurs 4–5h after serum `step-up' was substantially diminished by increasing the concentration of Mg2+ ions, but not of Na+ or K+ ions, in the medium by 30mm, 30min before addition of serum, and this inhibition was maintained for at least 24h. Methylglyoxal bis(guanylhydrazone), added to serum-deprived cultures to a concentration of 20μm, 30min before addition of serum, severely inhibited the increase in cell growth. The inhibitory effects of the drug were prevented by simultaneous addition of spermidine to the medium (to 100μm), and were partly prevented by the simultaneous addition of Mg2+ ions (to 30mm). Mg2+ ions were particularly effective in overcoming the inhibitory effect of methylglyoxal bis(guanylhydrazone) on the synthesis of DNA. Thus although a certain lack of specificity for cations exists in BHK-21/C13 cells, in that Mg2+ ions can be substituted for polyamines, particularly spermidine, to some extent, there are cellular processes for which the requirement for polyamines as cations is specific. PMID:444220

Influence of ZrO2 addition on the microstructure and discharge properties of Mg-Zr-O protective layers in alternating current plasma display panels

NASA Astrophysics Data System (ADS)

Guo, Bingang; Liu, Chunliang; Song, Zhongxiao; Liu, Liu; Fan, Yufeng; Xia, Xing; Fan, Duowang

2005-08-01

Mg-Zr-O protective layers for alternating current plasma display panels were deposited by e-beam evaporation. The effect of the ZrO2 addition on both the discharge properties [firing voltage Vf, minimum sustaining voltage Vs, and memory coefficient (MC)] and the microstructure of deposited Mg-Zr-O films were investigated. The results show that the film microstructure changes and the electron emission enhancement due to the ZrO2 addition are the main reasons for the improvements of the discharge properties of Mg-Zr-O films. A small amount of Zr solution in MgO under its solid solubility can effectively increase the outer-shell valence electron emission yield so as to decrease Vf and Vs compared with using a pure MgO protective layer. The ZrO2/(MgO +ZrO2) ratio has a great effect on the film surface conditions. Proper surface morphologies make a good contribution to obtain large MC in accordance with lower firing voltage.

Detection of Mycoplasma gallisepticum in House Finches ( Haemorhous mexicanus) from Arizona.

PubMed

Staley, Molly; Bonneaud, Camille; McGraw, Kevin J; Vleck, Carol M; Hill, Geoffrey E

2018-03-01

In 1994, an endemic poultry pathogen, Mycoplasma gallisepticum (MG), was identified as the causative agent of a novel disease in house finches ( Haemorhous mexicanus). After an initial outbreak in Maryland, MG spread rapidly throughout eastern North American populations of house finches. Subsequently, MG spread slowly through the northern interior of North America and then into the Pacific Northwest, finally reaching California in 2006. Until 2009, there were no reports of MG in the southwestern United States east of California. In August 2011, after reports of house finches displaying conjunctivitis characteristic of MG infection in Arizona, we trapped house finches at bird feeders in central Arizona (Tempe) and southern Arizona (Tucson and Green Valley) to assay for MG infection. Upon capture, we noted whether birds exhibited conjunctivitis, and we collected choanal swabs to test for the presence of MG DNA using PCR. We detected MG in finches captured from Green Valley (in ∼12% of birds captured), but not in finches from Tucson or Tempe. Based on resampling of house finches at these sites in July 2014, we suggest that central Arizona finches likely remain unexposed to MG. We also suggest that low urban connectivity between arid habitats of southern and central Arizona or a reduction in the prevalence of MG after its initial arrival in Arizona may be limiting the spread of MG from south to north in Arizona. In addition, the observed conjunctivitis-like signs in house finches that were negative for MG by PCR may be caused primarily by avian pox virus.

Partially reduced graphene oxide-gold nanorods composite based bioelectrode of improved sensing performance.

PubMed

Nirala, Narsingh R; Abraham, Shiju; Kumar, Vinod; Pandey, Shobhit A; Yadav, Umakant; Srivastava, Monika; Srivastava, S K; Singh, Vidya Nand; Kayastha, Arvind M; Srivastava, Anchal; Saxena, Preeti S

2015-11-01

The present work proposes partially reduced graphene oxide-gold nanorods supported by chitosan (CH-prGO-AuNRs) as a potential bioelectrode material for enhanced glucose sensing. Developed on ITO substrate by immobilizing glucose oxidase on CH-prGO-AuNRs composite, these CH-prGO-AuNRs/ITO bioelectrodes demonstrate high sensitivity of 3.2 µA/(mg/dL)/cm(2) and linear range of 25-200 mg/dL with an ability to detect as low as 14.5 mg/dL. Further, these CH-prGO-AuNRs/ITO based electrodes attest synergistiacally enhanced sensing properties when compared to simple graphene oxide based CH-GO/ITO electrode. This is evident from one order higher electron transfer rate constant (Ks) value in case of CH-prGO-AuNRs modified electrode (12.4×10(-2) cm/s), in contrast to CH-GO/ITO electrode (6×10(-3) cm/s). Additionally, very low Km value [15.4 mg/dL(0.85 mM)] ensures better binding affinity of enzyme to substrate which is desirable for good biosensor stability and resistance to environmental interferences. Hence, with better loading capacity, kinetics and stability, the proposed CH-prGO-AuNRs composite shows tremendous potential to detect several bio-analytes in the coming future. Copyright © 2015 Elsevier B.V. All rights reserved.

Excess dietary cobalt in pigs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huck, D.W.; Clawson, A.J.

1976-01-01

Five experiments were conducted, in which 240 growing finishing pigs were used, to determine the level of Cobalt (Co) which is toxic. Pigs tolerated up to 200 mg/kg of Co when added to corn-soybean meal diets containing 82 to 178 mg/kg of iron. The addition of 400 or 600 mg/kg of Co caused anorexia, growth depression, stiff-leggedness, humped back, incoordination and extreme muscular tremors. Serum and organ levels of Co were greatly increased and serum and organ levels of iron (Fe) were significantly reduced by added dietary cobalt. The addition of .5 or 1.0% methionine to the diet completely alleviatedmore » the toxic affects caused by the 600 mg level of Co and restored serum Fe to near normal levels. The addition of Fe, manganese (Mn) and zinc (Zn) in combination at levels of 200, 400 and 400 mg/kg, respectively, also alleviated the growth depression caused by the 400 mg level of Co and higher levels of Fe, Mn and Zn (200, 600 and 600 mg/kg) partially restored feed intake and growth when 600 mg of Co was fed. Iron alone was not effective in overcoming the growth depression caused by 400 or 600 mg/kg of dietary cobalt. 31 references, 1 figure, 11 tables.« less

Development of an efficient multigrid method for the NEM form of the multigroup neutron diffusion equation

NASA Astrophysics Data System (ADS)

Al-Chalabi, Rifat M. Khalil

1997-09-01

Development of an improvement to the computational efficiency of the existing nested iterative solution strategy of the Nodal Exapansion Method (NEM) nodal based neutron diffusion code NESTLE is presented. The improvement in the solution strategy is the result of developing a multilevel acceleration scheme that does not suffer from the numerical stalling associated with a number of iterative solution methods. The acceleration scheme is based on the multigrid method, which is specifically adapted for incorporation into the NEM nonlinear iterative strategy. This scheme optimizes the computational interplay between the spatial discretization and the NEM nonlinear iterative solution process through the use of the multigrid method. The combination of the NEM nodal method, calculation of the homogenized, neutron nodal balance coefficients (i.e. restriction operator), efficient underlying smoothing algorithm (power method of NESTLE), and the finer mesh reconstruction algorithm (i.e. prolongation operator), all operating on a sequence of coarser spatial nodes, constitutes the multilevel acceleration scheme employed in this research. Two implementations of the multigrid method into the NESTLE code were examined; the Imbedded NEM Strategy and the Imbedded CMFD Strategy. The main difference in implementation between the two methods is that in the Imbedded NEM Strategy, the NEM solution is required at every MG level. Numerical tests have shown that the Imbedded NEM Strategy suffers from divergence at coarse- grid levels, hence all the results for the different benchmarks presented here were obtained using the Imbedded CMFD Strategy. The novelties in the developed MG method are as follows: the formulation of the restriction and prolongation operators, and the selection of the relaxation method. The restriction operator utilizes a variation of the reactor physics, consistent homogenization technique. The prolongation operator is based upon a variant of the pin power reconstruction methodology. The relaxation method, which is the power method, utilizes a constant coefficient matrix within the NEM non-linear iterative strategy. The choice of the MG nesting within the nested iterative strategy enables the incorporation of other non-linear effects with no additional coding effort. In addition, if an eigenvalue problem is being solved, it remains an eigenvalue problem at all grid levels, simplifying coding implementation. The merit of the developed MG method was tested by incorporating it into the NESTLE iterative solver, and employing it to solve four different benchmark problems. In addition to the base cases, three different sensitivity studies are performed, examining the effects of number of MG levels, homogenized coupling coefficients correction (i.e. restriction operator), and fine-mesh reconstruction algorithm (i.e. prolongation operator). The multilevel acceleration scheme developed in this research provides the foundation for developing adaptive multilevel acceleration methods for steady-state and transient NEM nodal neutron diffusion equations. (Abstract shortened by UMI.)

An oral carcinogenicity and toxicity study of senna (Tinnevelly senna fruits) in the rat.

PubMed

Mitchell, J M; Mengs, U; McPherson, S; Zijlstra, J; Dettmar, P; Gregson, R; Tigner, J C

2006-01-01

Senna (Tinnevelly senna fruits), a known laxative derived from plants, was administered by gavage to Sprague-Dawley (Crl:CD (SD) BR) rats once daily at dose levels of 0, 25, 100 and 300 mg/kg/day for up to 104 consecutive weeks. Based upon clinical signs related to the laxation effect of senna, the highest dose (300 mg/kg/day) was considered to be a maximum tolerated dose. Sixty animals per sex were assigned to the control and dose groups. Assessments included clinical chemistry, hematology, full histology (control and high-dose groups; in addition, low and mid dose: intestinal tract, adrenals, liver, kidneys, brain and gross lesions) and toxicokinetics. The primary treatment-related clinical observation was mucoid feces seen at 300 mg/kg/day. When compared to controls, animals administered 300 mg/kg/day had slightly reduced body weights, increased water consumption and notable changes in electrolytes in serum (increases in potassium and chloride) and urine (decreases in sodium, potassium and chloride). The changes in electrolytes are most likely physiologic adaptations to the laxative effect of senna. At necropsy, dark discoloration of the kidneys was observed in animals in all treated groups. Histological changes were seen in the kidneys of animals from all treated groups and included slight to moderate tubular basophilia and tubular pigment deposits. In addition, for all treated groups, minimal to slight hyperplasia was evident in the colon and cecum. These histological changes, together with the changes seen in the evaluation of clinical chemistry and urine parameters, have been shown to be reversible in a previous 13-week rat study of senna. No treatment-related neoplastic changes were observed in any of the examined organs. Based upon these data, it is concluded that senna is not carcinogenic even after daily administration for 2 years at dosages of up to 300 mg/kg/day in Sprague-Dawley rats.

Detection of myasthenia gravis using electrooculography signals.

PubMed

Liang, T; Boulos, M I; Murray, B J; Krishnan, S; Katzberg, H; Umapathy, K

2016-08-01

Myasthenia gravis (MG) is an autoimmune neuromuscular disorder resulting from skeletal muscle weakness and fatigue. An early common symptom is fatigable weakness of the extrinsic ocular muscles; if symptoms remain confined to the ocular muscles after a few years, this is classified as ocular myasthenia gravis (OMG). Diagnosis of MG when there are mild, isolated ocular symptoms can be difficult, and currently available diagnostic techniques are insensitive, non-specific or technically cumbersome. In addition, there are no accurate biomarkers to follow severity of ocular dysfunction in MG over time. Single-fiber electromyography (SFEMG) and repetitive nerve stimulation (RNS) offers a way of detecting and measuring ocular muscle dysfunction in MG, however, challenges of these methods include a poor signal to noise ratio in quantifying eye muscle weakness especially in mild cases. This paper presents one of the attempts to use the electric potentials from the eyes or electrooculography (EOG) signals but obtained from three different forms of sleep testing to differentiate MG patients from age- and gender-matched controls. We analyzed 8 MG patients and 8 control patients and demonstrated a difference in the average eye movements detected between the groups. A classification accuracy as high as 68.8% was achieved using a linear discriminant analysis based classifier.

Formation process of micro arc oxidation coatings obtained in a sodium phytate containing solution with and without CaCO3 on binary Mg-1.0Ca alloy

NASA Astrophysics Data System (ADS)

Zhang, R. F.; Zhang, Y. Q.; Zhang, S. F.; B. Qu; Guo, S. B.; Xiang, J. H.

2015-01-01

Micro arc oxidation (MAO) is an effective method to improve the corrosion resistance of magnesium alloys. In order to reveal the influence of alloying element Ca and CaCO3 electrolyte on the formation process and chemical compositions of MAO coatings on binary Mg-1.0Ca alloy, anodic coatings after different anodizing times were prepared on binary Mg-1.0Ca alloy in a base solution containing 3 g/L sodium hydroxide and 15 g/L sodium phytate with and without addition of CaCO3. The coating formation was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The results show that Mg-1.0Ca alloy is composed of two phases, the Mg phase and Mg2Ca phase. After treating for 5 s, the coating began to develop and was preferentially formed on the area nearby Mg2Ca phase, which may be resulted from the intrinsic electronegative potential of the Mg phase than that of Mg2Ca phase. Anodic coatings unevenly covered the total surface after 20 s. After 80 s, the coatings were uniformly developed on Mg-1.0Ca alloy with micro pores. During MAO process, some sodium phytate molecules are hydrolyzed into inorganic phosphate. CaCO3 has minor influence on the calcium content of the obtained MAO coatings.

What is a food and what is a medicinal product in the European Union? Use of the benchmark dose (BMD) methodology to define a threshold for "pharmacological action".

PubMed

Lachenmeier, Dirk W; Steffen, Christian; el-Atma, Oliver; Maixner, Sibylle; Löbell-Behrends, Sigrid; Kohl-Himmelseher, Matthias

2012-11-01

The decision criterion for the demarcation between foods and medicinal products in the EU is the significant "pharmacological action". Based on six examples of substances with ambivalent status, the benchmark dose (BMD) method is evaluated to provide a threshold for pharmacological action. Using significant dose-response models from literature clinical trial data or epidemiology, the BMD values were 63mg/day for caffeine, 5g/day for alcohol, 6mg/day for lovastatin, 769mg/day for glucosamine sulfate, 151mg/day for Ginkgo biloba extract, and 0.4mg/day for melatonin. The examples for caffeine and alcohol validate the approach because intake above BMD clearly exhibits pharmacological action. Nevertheless, due to uncertainties in dose-response modelling as well as the need for additional uncertainty factors to consider differences in sensitivity within the human population, a "borderline range" on the dose-response curve remains. "Pharmacological action" has proven to be not very well suited as binary decision criterion between foods and medicinal product. The European legislator should rethink the definition of medicinal products, as the current situation based on complicated case-by-case decisions on pharmacological action leads to an unregulated market flooded with potentially illegal food supplements. Copyright © 2012 Elsevier Inc. All rights reserved.

Effects of dietary cadmium on growth, antioxidants and bioaccumulation of sea cucumber (Apostichopus japonicus) and influence of dietary vitamin C supplementation.

PubMed

Wang, Jing; Ren, Tongjun; Wang, Fuqiang; Han, Yuzhe; Liao, Mingling; Jiang, Zhiqiang; Liu, Haiying

2016-07-01

The effects of dietary cadmium (Cd) supplementation on growth, antioxidant capacity and accumulation of Cd in tissues (body wall, digestive tracts, and respiratory tree) of sea cucumber, Apostichopus japonicus, exposed to sub-chronic concentrations (0, 10, 50, 100, and 500mg Cd/kg dry weight) of Cd were investigated. In addition, the potential protective effects of vitamin C (L-ascorbic acid, AsA) against the effects of Cd on sea cucumbers were investigated. Sea cucumbers were exposed to dietary Cd for 30 days, after which another group of healthy sea cucumbers was supplied diet supplemented with mixed Cd and AsA for another 30 days. Cd exposure for 30 days resulted in increased Cd accumulation in tissues of sea cucumbers with exposure time and concentration. The order of Cd accumulation in organs was digestive tracts>respiratory tree>body wall. On day 30, the body weight gain (BWG) and specific growth rate (SGR) decreased significantly (P<0.05) in the 500mg Cd/kg treatment. Superoxide dismutase (SOD) activity, glutathione peroxidase (GSH-Px) activity and catalase (CAT) activity in the coelomic fluid of sea cucumbers decreased with increasing dietary Cd concentration, but malondialdehyde (MDA) content in the coelomic fluid increased. Providing diet supplemented with Cd and AsA indicated that although sea cucumbers exhibited signs of Cd toxicity, no death occurred in response to 50mg Cd/kg for 30 days. Based on these findings, five treatments were provided: 50mg Cd/kg+0mg AsA/kg, 50mg Cd/kg+ 3000mg AsA/kg, 50mg Cd/kg+ 5000mg AsA/kg, 50mg Cd/kg+10,000mg AsA/kg, and 50mg Cd/kg+15,000mg AsA/kg. The BWG and SGR of sea cucumbers fed the AsA supplemented diet mixed with Cd increased. Additionally, MDA levels in coelomic fluid were negatively correlated with dietary AsA levels, while antioxidant capacities (SOD, GSH-Px and CAT) were positively correlated with dietary AsA levels. Moreover, Cd accumulation in tissues decreased in response to dietary AsA supplementation of treatments. Overall, antioxidant capacity and bioaccumulation in sea cucumber was found to decrease and be induced in response to Cd, but vitamin C mitigated these effects, with 5000mg AsA/kg providing the optimum protection against 50mg/kg Cd. Copyright © 2016 Elsevier Inc. All rights reserved.

The rise and fall of novel renal magnesium transporters.

PubMed

Schäffers, Olivier J M; Hoenderop, Joost G J; Bindels, René J M; de Baaij, Jeroen H F

2018-06-01

Body Mg 2+ balance is finely regulated in the distal convoluted tubule (DCT), where a tight interplay among transcellular reabsorption, mitochondrial exchange, and basolateral extrusion takes place. In the last decades, several research groups have aimed to identify the molecular players in these processes. A multitude of proteins have been proposed to function as Mg 2+ transporter in eukaryotes based on phylogenetic analysis, differential gene expression, and overexpression studies. However, functional evidence for many of these proteins is lacking. The aim of this review is, therefore, to critically reconsider all putative Mg 2+ transporters and put their presumed function in context of the renal handling of Mg 2+ . Sufficient experimental evidence exists to acknowledge transient receptor potential melastatin (TRPM) 6 and TRPM7, solute carrier family 41 (SLC41) A1 and SLC41A3, and mitochondrial RNA splicing 2 (MRS2) as Mg 2+ transporters. TRPM6/7 facilitate Mg 2+ influx, SLC41A1 mediates Mg 2+ extrusion, and MRS2 and SLC41A3 are implicated in mitochondrial Mg 2+ homeostasis. These proteins are highly expressed in the DCT. The function of cyclin M (CNNM) proteins is still under debate. For the other proposed Mg 2+ transporters including Mg 2+ transporter subtype 1 (MagT1), nonimprinted in Prader-Willi/Angelman syndrome (NIPA), membrane Mg 2+ transport (MMgT), Huntingtin-interacting protein 14 (HIP14), and ATP13A4, functional evidence is limited, or functions alternative to Mg 2+ transport have been suggested. Additional characterization of their Mg 2+ transport proficiency should be provided before further claims about their role as Mg 2+ transporter can be made.

Ion Sensor Properties of Fluorescent Schiff Bases Carrying Dipicolylamine Groups. A Simple Spectrofluorimetric Method to Determine Cu (II) in Water Samples.

PubMed

Vanlı, Elvan; Mısır, Miraç Nedim; Alp, Hakan; Ak, Tuğba; Özbek, Nurhayat; Ocak, Ümmühan; Ocak, Miraç

2017-09-01

Four fluorescent Schiff bases carrying dipicolylamine groups were designed and synthesized to determine their ion sensor properties in partial aqueous solution. The corresponding amine compound and the aldehyde compounds such as 1-naphthaldehyde, 9-anthraldehyde, phenanthrene-9-carboxaldehyde and 1-pyrenecarboxaldehyde were used to prepare the new Schiff bases. The influence of many metal cations and anions on the spectroscopic properties of the ligands was investigated in ethanol-water (1:1) by means of emission spectrometry. From the spectrofluorimetric titrations, the complexation stoichiometry and complex stability constants of the ligands with Cd 2+ , Zn 2+ , Cu 2+ and Hg 2+ ions were determined. The ligands did not interact with the anions. However, the Schiff base derived from phenanthrene-9-carboxaldehyde showed sensitivity for Cu 2+ among the tested metal ions. The phenanthrene-based Schiff base was used as analytical ligand for the simple and fast determination of Cu 2+ ion in water samples. A modified standard addition method was used to eliminate matrix effect. The linear range was from 0.3 mg/L to 3.8 μg/L. Detection and quantification limits were 0.14 and 0.43 mg/L, respectively. Maximum contaminant level goal (MCLG) for copper in drinking water according to EPA is 1.3 mg/L. The proposed method has high sensitivity to determine copper in drinking waters.

Risk assessment of dietary exposure to aluminium in the Chinese population.

PubMed

Ma, Ning; Liu, Zhao-Ping; Yang, Da-Jin; Liang, Jiang; Zhu, Jiang-Hui; Xu, Hai-Bin; Li, Feng-Qin; Li, Ning

2016-10-01

In order to address the issue of excessive intake of aluminium (Al) from Al-containing food additives in the Chinese diet, this study conducted a dietary exposure assessment of Al in the general population based on the national surveillance data of Al content in foods and national food consumption data. It was found that the mean dietary exposure of the whole Chinese population to Al from Al-containing food additives was 1.795 mg kg ‒1 bw week ‒1 , not exceeding the PTWI, while high dietary exposures (e.g., 97.5 th percentile) to Al were 7.660 and 2.103-2.903 mg kg ‒1 bw week ‒1 for children, respectively, both exceeding the PTWI. It was found that the dietary exposure to Al for 32.5% of the total Chinese population and 42.6% of children aged 4-6 years exceeded the PTWI. Wheat flour and wheat-based products are the main source of dietary A l exposure (85% of the total intake); and puffed foods are the major source of Al intake for children. These findings suggested that consumption of Al-containing food additives could be a health concern for consumers with high food consumption (97.5 th percentile) and children under the age of 14 years.

Economics of small fully reusable launch systems (SSTO vs. TSTO)

NASA Astrophysics Data System (ADS)

Koelle, Dietrich E.

1997-01-01

The paper presents a design and cost comparison of an SSTO vehicle concept with two TSTO vehicle options. It is shown that the ballistic SSTO concept feasibility is NOT a subject of technology but of proper vehicle SIZING. This also allows to design for sufficient performance margin. The cost analysis has been performed with the TRANSCOST- Model, also using the "Standardized Cost per Flight" definition for the CpF comparison. The results show that a present-technology SSTO for LEO missions is about 30 % less expensive than any TSTO vehicle, based on Life-Cycle-Cost analysis, in addition to the inherent operational/ reliability advantages of a single-stage vehicle. In case of a commercial development and operation it is estimated that an SSTO vehicle with 400 Mg propellant mass can be flown for some 9 Million per mission (94/95) with 14 Mg payload to LEO, 7 Mg to the Space Station Orbit, or 2 Mg to a 200/800 km polar orbit. This means specific transportation cost of 650 /kg (300 $/lb), resp.3.2 MYr/Mg, to LEO which is 6 -10% of present expendable launch vehicles.

Fabrication and Characterization of Porous MgAl₂O₄ Ceramics via a Novel Aqueous Gel-Casting Process.

PubMed

Yuan, Lei; Liu, Zongquan; Liu, Zhenli; He, Xiao; Ma, Beiyue; Zhu, Qiang; Yu, Jingkun

2017-11-30

A novel and aqueous gel-casting process has been successfully developed to fabricate porous MgAl₂O₄ ceramics by using hydratable alumina and MgO powders as raw materials and deionized water as hydration agent. The effects of different amounts of deionized water on the hydration properties, apparent porosity, bulk density, microstructure, pore size distribution and compressive strength of the samples were investigated. The results indicated that the porosity and the microstructure of porous MgAl₂O₄ ceramics were governed by the amounts of deionized water added. The porous structure was formed by the liberation of physisorbed water and the decomposition of hydration products such as bayerite, brucite and boehmite. After determining the addition amounts of deionized water, the fabricated porous MgAl₂O₄ ceramics had a high apparent porosity (52.5-65.8%), a small average pore size structure (around 1-3 μm) and a relatively high compressive strength (12-28 MPa). The novel aqueous gel-casting process with easy access is expected to be a promising candidate for the preparation of Al₂O₃-based porous ceramics.

Methylglyoxal is associated with bacteriostatic activity of high fructose agave syrups.

PubMed

Corrales Escobosa, Alma Rosa; Gomez Ojeda, Armando; Wrobel, Kazimierz; Magana, Armando Alcazar; Wrobel, Katarzyna

2014-12-15

Three α-ketoaldehydes, potentially present in high fructose agave syrups (HFASs) as intermediates of the Maillard reaction, were determined. A previously reported HPLC-FLD procedure based on pre-column derivatisation with 4-methoxy-o-phenylenediamine was adopted, yielding the method quantification limits 0.11 mg/kg, 0.10mg/kg, 0.09 mg/kg for glyoxal, methylglyoxal (MGo) and diacetyl, respectively. The obtained results revealed high concentrations of methylglyoxal in HFASs (average 102 ± 91 mg/kg, range 15.6-315 mg/kg) as compared to commercial Mexican bee honeys or corn syrups. Hydrogen peroxide was generated in all HFASs upon dilution, yet to less extent than in bee honeys. HFASs presented bacteriostatic activity against Bacillus subtilis and Escherichia coli; catalase addition had minimum effect on the assay results in syrups with elevated MGo. Principal component analysis revealed direct association between growth inhibition and MGo. It is concluded that elevated concentration of MGo in HFASs is at least in part responsible for their non-peroxide bacteriostatic activity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Human treated dentin matrices combined with Zn-doped, Mg-based bioceramic scaffolds and human dental pulp stem cells towards targeted dentin regeneration.

PubMed

Bakopoulou, Athina; Papachristou, Eleni; Bousnaki, Maria; Hadjichristou, Christina; Kontonasaki, Eleana; Theocharidou, Anna; Papadopoulou, Lambrini; Kantiranis, Nikolaos; Zachariadis, George; Leyhausen, Gabriele; Geurtsen, Werner; Koidis, Petros

2016-08-01

This study aimed to investigate the potential of Mg-based bioceramic scaffolds combined with human treated-dentin matrices (hTDMs) and dentinogenesis-related morphogens to promote odontogenic differentiation and dentin-like tissue formation by Dental Pulp Stem Cells-DPSCs. DPSC cultures were established and characterized by flow cytometry. Experimental cavities were prepared inside crowns of extracted teeth and demineralized by EDTA (hTDMs). Zn-doped, Mg-based bioceramic scaffolds, synthesized by the sol-gel technique, were hosted inside the hTDMs. DPSCs were spotted inside the hTDMs/scaffold constructs with/without additional exposure to DMP-1 or BMP-2 (100ng/ml, 24h). Scanning Electron Microscopy-SEM, live/dead fluorescence staining and MTT assay were used to evaluate cell attachment and viability; Real time PCR for expression of osteo/odontogenic markers; Inductively Coupled Plasma-Atomic Emission Spectrometry-ICP/AES for scaffold elemental release analysis; ELISA for hTDM growth factor release analysis; SEM and X-ray Diffraction-XRD for structural/chemical characterization of the regenerated tissues. Scaffolds constantly released low concentrations of Mg(2+), Ca(2+), Zn(2+) and Si(4+), while hTDMs growth factors, like DMP-1, BMP-2 and TGFβ-1. hTDMs/scaffold constructs supported DPSC viability, inducing their rapid odontogenic shift, indicated by upregulation of DSPP, BMP-2, osteocalcin and osterix expression. Newly-formed Ca-P tissue overspread the scaffolds partially transforming into bioapatite. Exposure to DMP-1 or BMP-2 pronouncedly enhanced odontogenic differentiation phenomena. This is the first study to validate that combining the bioactivity and ion releasing properties of bioceramic materials with growth factor release by treated natural dentin further supported by exogenous addition of key dentinogenesis-related morphogens (DMP-1, BMP-2) can be a promising strategy for targeted dentin regeneration. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Pharmacokinetics of pediatric lopinavir/ritonavir tablets in children when administered twice daily according to FDA weight bands.

PubMed

Bastiaans, Diane E T; Forcat, Silvia; Lyall, Hermione; Cressey, Tim R; Hansudewechakul, Rawiwan; Kanjanavanit, Suparat; Noguera-Julian, Antoni; Königs, Christoph; Inshaw, Jamie R J; Chalermpantmetagul, Suwalai; Saïdi, Yacine; Compagnucci, Alexandra; Harper, Lynda M; Giaquinto, Carlo; Colbers, Angela P H; Burger, David M

2014-03-01

Lopinavir/ritonavir (LPV/r) pediatric tablets (100/25 mg) are approved by the United States Food and Drug Administration (FDA) and European Medicines Agency (EMA) as part of combination antiretroviral therapy. Dosing is based on body weight bands or body surface area under FDA approval and only body surface area by the EMA. This can lead to a different recommended dose. In addition, weight band-based dosing has not been formally studied in the target population. We evaluated the pharmacokinetics (PK) of LPV/r in children, administered twice daily according to the FDA weight bands, using pediatric tablets. Fifty-three HIV-infected children were included in the PK substudy of the Paediatric European Network for the Treatment of AIDS 18 trial (KONCERT). In this study, children were randomized to receive LPV/r twice or once daily, according to FDA weight bands. A PK assessment was performed in 17, 16 and 20 children in the 15-25 kg, ≥ 25-35 kg and >35 kg weight band, respectively, while children took the tablets twice daily. Rich sampling was performed, and PK parameters were calculated by noncompartmental analysis. Given the high percentage of Asian children, it was also tested whether there was a difference in PK parameters between Asian and non-Asian children. For the total group, LPV geometric mean AUC0-12, Cmax and C12 were 106.9 h × mg/L, 12.0 mg/L and 4.9 mg/L, respectively. There were no significant differences in LPV PK parameters between the weight bands. In addition, weight was not found to be associated with variability in Cmax, C12 or AUC0-12 for the LPV PK parameters. FDA weight band-based dosing recommendations provide adequate exposure to LPV when using LPV/r pediatric tablets.

Effects of Sn Addition on the Microstructures and Mechanical Properties of Mg-6Zn-3Cu- xSn Magnesium Alloys

NASA Astrophysics Data System (ADS)

Zhang, Tao; Shen, Jun; Sang, Jia-Xin; Li, Yang; He, Pei-Pei

2015-08-01

In this paper, Mg-6Zn-3Cu- xSn (ZC63- xSn) magnesium alloys with different Sn contents (0, 1, 2, 4 wt pct) were fabricated and subjected to different heat treatments. The microstructures and mechanical properties of the obtained ZC63- xSn samples were investigated by optical microscopy, X-ray diffraction, scanning electron microscopy, Vickers hardness testing, and tensile testing. It was found that the As-cast Mg-6Zn-3Cu (ZC63) magnesium alloy mainly contained α-Mg grains and Mg(Zn,Cu) particles. Sn dissolved in α-Mg grains when Sn content was below 2 wt pct while Mg2Sn phase forms in the case of Sn content was above 4 wt pct. Addition of Sn refined both α-Mg grains and Mg(Zn,Cu) particles, and increased the volume fraction of Mg(Zn,Cu) particles. Compared with the Sn-free alloy, the microhardness of Sn-containing alloys increased greatly and that of As-extrude ZC63-4Sn sample achieved the highest value. The strength of ZC63 magnesium alloy was significantly enhanced because of Sn addition, which was attributed to grain refinement strengthening, solid solution strengthening, and precipitation strengthening. Furthermore, the ultimate yield stress, yield strength, and elongation of ZC63- xSn magnesium alloys were increased owing to the deceasing grain size induced by extrusion process.

Giant increase in piezoelectric coefficient of AlN by Mg-Nb simultaneous addition and multiple chemical states of Nb

NASA Astrophysics Data System (ADS)

Uehara, Masato; Shigemoto, Hokuto; Fujio, Yuki; Nagase, Toshimi; Aida, Yasuhiro; Umeda, Keiichi; Akiyama, Morito

2017-09-01

Aluminum nitride (AlN) is one of piezoelectric materials, which are eagerly anticipated for use in microelectromechanical systems (MEMS) applications such as communication resonators, sensors, and energy harvesters. AlN is particularly excellent in generated voltage characteristics for the MEMS rather than oxide piezoelectric materials such as lead zirconium titanate Pb(Zr, Ti)O3. However, it is necessary to improve the piezoelectric properties of AlN in order to advance the performance of the MEMS. We dramatically increased the piezoelectric coefficient d33 of AlN films by simultaneously adding magnesium (Mg) and niobium (Nb). The d33 of Mg39.3Nb25.0Al35.7N is 22 pC/N, which is about four times that of AlN. The d33 is increased by Mg and Nb simultaneous addition, and is not increased by Mg or Nb single addition. Interestingly, the Nb has multiple chemical states, and which are influenced by the Mg concentration.

Graphene addition to MgB{sub 2} superconductor obtained by ex-situ spark plasma sintering technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aldica, G.; Burdusel, M.; Popa, S.

Highlights: • Graphene-added dense MgB{sub 2} was prepared by ex-situ spark plasma sintering. • There is a limited interaction between graphene and MgB{sub 2}. • Addition of graphene (G) shows a small enhancement of J{sub c} and μ{sub 0}H{sub irr}. • G is one of the least effective C-containing additions. - Abstract: Graphene nanopowder (G) with average thickness particle size of about 6–8 nm was added to MgB{sub 2} commercial powder. Starting composition was (MgB{sub 2}){sub (1−x)}(G){sub x}, x = 0.0125, 0.025, 0.05. Processing was performed by Spark Plasma Sintering (SPS) technique. All added samples have high density (above 95%).more » The critical temperature (T{sub c}) and the lattice parameter a (c-axis lattice parameter is constant) show a small variation suggesting that carbon substitution for boron is low. TEM observations show the presence of un-reacted graphene plates supporting the T{sub c} and structural results. It also indicates that G-addition does not modify the MgB{sub 2} microstructure. Despite this, there is an optimum doped sample (MgB{sub 2}){sub 0.9875}(G){sub 0.0125} for which the critical current density at temperatures below 25 K is slightly higher at high magnetic fields than for the pristine sample. The addition of G is found as one of the least effective C-source additions enhancing J{sub c}. We discuss results as being strongly related to variation of the residual stress.« less

Stabilization of heavy metals in MSWI fly ash using silica fume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xinying; Chen, Quanyuan; State Environmental Protection Engineering Center for Pollution Treatment and Control in Textile Industry, Donghua University, Shanghai 201620

Highlights: • The stabilization of heavy metals in MSWI fly ash was investigated. • The addition of silica fume effectively reduced the leaching of Pb and Cd. • The relation of solid phase transformation and leaching behavior of heavy metals was discussed. - Abstract: The objective of this work was to investigate the feasibility and effectiveness of silica fume on stabilizing heavy metals in municipal solid waste incineration (MSWI) fly ash. In addition to compressive strength measurements, hydrated pastes were characterized by X-ray diffraction (XRD), thermal-analyses (DTA/TG), and MAS NMR ({sup 27}Al and {sup 29}Si) techniques. It was found thatmore » silica fume additions could effectively reduce the leaching of toxic heavy metals. At the addition of 20% silica fume, leaching concentrations for Cu, Pb and Zn of the hydrated paste cured for 7 days decreased from 0.32 mg/L to 0.05 mg/L, 40.99 mg/L to 4.40 mg/L, and 6.96 mg/L to 0.21 mg/L compared with the MSWI fly ash. After curing for 135 days, Cd and Pb in the leachates were not detected, while Cu and Zn concentrations decreased to 0.02 mg/L and 0.03 mg/L. The speciation of Pb and Cd by the modified version of the European Community Bureau of Reference (BCR) extractions showed that these metals converted into more stable state in hydrated pastes of MSWI fly ash in the presence of silica fume. Although exchangeable and weak-acid soluble fractions of Cu and Zn increased with hydration time, silica fume addition of 10% can satisfy the requirement of detoxification for heavy metals investigated in terms of the identification standard of hazardous waste of China.« less

TG/DTG/DTA evaluation of flame retarded cotton fabrics and comparison to cone calorimeter data.

PubMed

Šimkovic, Ivan

2012-10-01

Unbleached cotton fabrics (UCF) with 12.5% polypropylene scrim treated with two phosphate-urea based fire-retardant (FR) formulations were evaluated for FR properties using thermogravimetry/differential thermogravimetry/differential thermal analysis (TG/DTG/DTA) method. In addition to testing the two FR-treated unbleached cotton fabrics (CF-FR1 and CF-FR2), bleached cotton fabric (BCF) treated with the two FR formulations (BCF-FR1 and BCF-FR2) was evaluated. Both formulations were washable with add-on of FR chemicals at 18.7% (FR1) or 17.4% (FR2) for UCF and 22.5% (FR1) or 24.9% (FR2) for BCF. The decreasing order of sums at maximal rates of samples degradation in air environment according to DTG method was: BCF (21.40%/min)>UCF (12.91%/min)>BCF-FR2 (12.83%/min)>BCF-FR1 (11.68%/min)>CF-FR2 (10.20%/min)>CF-FR1 (9.73%/min). It indicates that both formulations cause the decrease of thermooxidation of the products at slower rates than the starting material. Several endo- and exothermic peaks observed by DTA in inert and oxidative environment gives additional information about the degradation process. The order of decreasing thermal responses of the studied samples based on sums of DTA peak values of endothermic and exothermic peaks in air environment is: UCF (0.597 °C/mg)>BCF (0.120 °C/mg)>CF-FR1 (0.089 °C/mg)>BCF-FR1 (0.077 °C/mg)>CF-FR2 (0.062 °C/mg)>BCF-FR2 (0.053 °C/mg). This is in agreement with the cone calorimeter results according to which the flammability properties are improving with the decreasing heat release rates or ignition time prolongation in order: UCF>CF-FR1>CF-FR2. The advantage of TG/DTG/DTA method is slower linear heating rate, which allows the more detailed evaluation of the light and flammable cotton fabric. Copyright © 2012 Elsevier Ltd. All rights reserved.

Box-Behnken design approach towards optimization of activated carbon synthesized by co-pyrolysis of waste polyester textiles and MgCl2

NASA Astrophysics Data System (ADS)

Yuan, Zhihang; Xu, Zhihua; Zhang, Daofang; Chen, Weifang; Zhang, Tianqi; Huang, Yuanxing; Gu, Lin; Deng, Haixuan; Tian, Danqi

2018-01-01

Pyrolysis activation of waste polyester textiles (WPT) was regarded as a sustainable technique to synthesize multi-pore activated carbons. MgO-template method of using MgCl2 as the template precursor was employed, which possessed the advantages of ideal pore-forming effect and efficient preparation process. The response surface methodology coupled with Box-Behnken design (BBD) was conducted to study the interaction between different variables and optimized preparation conditions of waste polyester textiles based activated carbons. Derived from BBD design results, carbonization temperature was the most significant individual factor. And the maximum specific surface area of 1364 m2/g, which presented a good agreement with the predicted response values(1315 m2/g), was obtained at mixing ratio in MgCl2/WPT, carbonization temperature and time of 5:1, 900 °C and 90 min, respectively. Furthermore, the physicochemical properties of the sample prepared under optimal conditions were carried on utilizing nitrogen adsorption/desorption isotherms, EA, XRD, SEM and FTIR. In addition, the pore-forming mechanism was mainly attributed to the tendency of carbon layer coating on MgO to form pore walls after elimination of MgO and the strong dehydration effect of MgCl2 on WPT.

Delivery of phytochemical thymoquinone using molecular micelle modified poly(D, L lactide-co-glycolide) (PLGA) nanoparticles

NASA Astrophysics Data System (ADS)

Ganea, Gabriela M.; Fakayode, Sayo O.; Losso, Jack N.; van Nostrum, Cornelus F.; Sabliov, Cristina M.; Warner, Isiah M.

2010-07-01

Continuous efforts have been made in the development of potent benzoquinone-based anticancer drugs aiming for improved water solubility and reduced adverse reactions. Thymoquinone is a liposoluble benzoquinone-based phytochemical that has been shown to have remarkable antioxidant and anticancer activities. In the study reported here, thymoquinone-loaded PLGA nanoparticles were synthesized and evaluated for physico-chemical, antioxidant and anticancer properties. The nanoparticles were synthesized by an emulsion solvent evaporation method using anionic molecular micelles as emulsifiers. The system was optimized for maximum entrapment efficiency using a Box-Behnken experimental design. Optimum conditions were found for 100 mg PLGA, 15 mg TQ and 0.5% w/v poly(sodium N-undecylenyl-glycinate) (poly-SUG). In addition, other structurally related molecular micelles such as poly(sodium N-heptenyl-glycinate) (poly-SHG), poly(sodium N-undecylenyl-leucinate) (poly-SUL), and poly(sodium N-undecylenyl-valinate) (poly-SUV) were also examined as emulsifiers. All investigated molecular micelles provided excellent emulsifier properties, leading to maximum optimized TQ entrapment efficiency, and monodispersed particle sizes below 200 nm. The release of TQ from molecular micelle modified nanoparticles was investigated by dialysis and reached lower levels than the free drug. The antioxidant activity of TQ-loaded nanoparticles, indicated by IC50 (mg ml - 1 TQ for 50% 2,2-diphenyl-1-picrylhydrazyl (DPPH) scavenging activity), was highest for poly-SUV emulsified nanoparticles (0.030 ± 0.002 mg ml - 1) as compared to free TQ. In addition, it was observed that TQ-loaded nanoparticles emulsified with poly-SUV were more effective than free TQ against MDA-MB-231 cancer cell growth inhibition, presenting a cell viability of 16.0 ± 5.6% after 96 h.

In vitro propagation of female Ephedra foliata Boiss. & Kotschy ex Boiss.: an endemic and threatened Gymnosperm of the Thar Desert.

PubMed

Lodha, Deepika; Rathore, Nisha; Kataria, Vinod; Shekhawat, N S

2014-07-01

Ephedra foliata Boiss. & Kotschy ex Boiss., (family - Ephedraceae), is an ecologically and economically important threatened Gymnosperm of the Indian Thar Desert. A method for micropropagation of E. foliata using nodal explant of mature female plant has been developed. Maximum bud-break (90 %) of the explant was obtained on MS medium supplemented with 1.5 mg l(-1) of benzyl adenine (BA) + additives. Explant produces 5.3 ± 0.40 shoots from single node with 3.25 ± 0.29 cm length. The multiplication of shoots in culture was affected by salt composition of media, types and concentrations of plant growth regulators (PGR's) and their interactions, time of transfer of the cultures. Maximum number of shoots (26.3 ± 0.82 per culture vessel) were regenerated on MS medium modified by reducing the concentration of nitrates to half supplemented with 200 mg l(-1) ammonium sulphate {(NH4) 2SO4} (MMS3) + BA (0.25 mg l(-1)), Kinetin (Kin; 0.25 mg l(-1)), Indole-3-acetic acid (IAA; 0.1 mg l(-1)) and additives. The in vitro produced shoots rooted under ex vitro on soilrite moistened with one-fourth strength of MS macro salts in screw cap bottles by treating the shoot base (s) with 500 mg l(-1) of Indole-3-butyric acid (IBA) for 5 min. The micropropagated plants were hardened in the green house. The described protocol can be applicable for (i) large scale plant production (ii) establishment of plants in natural habitat and (iii) germplasm conservation of this endemic Gymnosperm of arid regions.

Effect of iron and magnesium addition for ethanol production from the conversion of palm oil mill effluent by anaerobic processes

NASA Astrophysics Data System (ADS)

Handajani, M.; Gumilar, A.; Syafila, M.

2018-01-01

Nowadays, crisis of the energy is the main problem in the world. Currently, most the energy resource derived from the fossil material that cannot be refurbished. Ethanol is an alternative fuel that content as a fossil fuels. Wastewater with the high concentration of the organic can be used for the ethanol production to replace foodstuff as a raw material. In this study, palm oil mill effluent (POME) with the concentration of COD is 24,500 mg/L has been used as a substrate. The purpose of this study was to determine the effect of the metal addition in the substrate metabolic pathways. Circulating batch reactor (CBR) is used with the flushing N2 1L/min for 24 hours and continued operates for 72 hours by internal biogas. The additional variation concentration of Fe(II) ion are 0.5; 1.0 and 2.5 mg/L, and Mg(II) are 0.5 and 1.5 mg/L were added by combination. The results showed that the combination of Fe (II) 2.5 mg/L and Mg(II) 1.5 mg/L produced the highest ethanol concentration is 715.8 mg/L and degree of acidification (DA) 0.284-0.357. Another combination of Fe(II) and Mg(II) provide results for the ethanol production 463.7-689.7 mg/L with the rate of ethanol production is 1.09-26.5 mg/L/hour.

Effect of Boron Addition on the Thermal, Degradation, and Cytocompatibility Properties of Phosphate-Based Glasses

PubMed Central

Hasan, Muhammad S.; Parsons, Andrew J.; Furniss, David; Scotchford, Colin A.; Ahmed, Ifty; Rudd, Chris D.

2013-01-01

In this study eight different phosphate-based glass compositions were prepared by melt-quenching: four in the (P2O5)45-(CaO)16-(Na2O)15-x -(MgO)24-(B2O3)x system and four in the system (P2O5)50-(CaO)16-(Na2O)10-x-(MgO)24-(B2O3)x, where x = 0,1, 5 and 10 mol%. The effect of B2O3 addition on the thermal properties, density, molar volume, dissolution rates, and cytocompatibility were studied for both glass systems. Addition of B2O3 increased the glass transition (T g), crystallisation (T c), melting (T m), Liquidus (T L) and dilatometric softening (T d) temperature and molar volume (V m). The thermal expansion coefficient (α) and density (ρ) were seen to decrease. An assessment of the thermal stability of the glasses was made in terms of their processing window (crystallisation onset, T c,ons minus glass transition temperature, T g), and an increase in the processing window was observed with increasing B2O3 content. Degradation studies of the glasses revealed that the rates decreased with increasing B2O3 content and a decrease in degradation rates was also observed as the P2O5 content reduced from 50 to 45 mol%. MG63 osteoblast-like cells cultured in direct contact with the glass samples for 14 days revealed comparative data to the positive control for the cell metabolic activity, proliferation, ALP activity, and morphology for glasses containing up to 5 mol% of B2O3. PMID:23991425

Thermal characterization of GaN-based laser diodes by forward-voltage method

NASA Astrophysics Data System (ADS)

Feng, M. X.; Zhang, S. M.; Jiang, D. S.; Liu, J. P.; Wang, H.; Zeng, C.; Li, Z. C.; Wang, H. B.; Wang, F.; Yang, H.

2012-05-01

An expression of the relation between junction temperature and forward voltage common for both GaN-based laser diodes (LDs) and light emitting diodes is derived. By the expression, the junction temperature of GaN-based LDs emitting at 405 nm was measured at different injection current and compared with the result of micro-Raman spectroscopy, showing that the expression is reasonable. In addition, the activation energy of Mg in AlGaN/GaN superlattice layers is obtained based on the temperature dependence of forward voltage.

Application of Liquid Chromatography/Ion Trap Mass Spectrometry Technique to Determine Ergot Alkaloids in Grain Products

PubMed Central

Szymczyk, Krystyna; Jędrzejczak, Renata; Roszko, Marek

2015-01-01

Summary A liquid chromatography/ion trap mass spectrometry-based method to determine six ergot alkaloids and their isomers is presented. The samples were cleaned on neutral alumina-based solid-phase extraction cartridges. The following method parameters were obtained (depending on the analyte and spiking level): method recovery from 63.0 to 104.6%, relative standard deviation below 18%, linear range from 1 to 325 µg/kg, linear correlation coefficient not less than 0.98. The developed analytical procedure was applied to determine the levels of ergot alkaloids in 65 samples of selected rye-based food products (flour – 34 samples, bran – 12 samples, rye – 18 samples, flakes – 1 sample). Measurable levels of alkaloids were found in majority of the analysed samples, particularly in rye flour. Additionally, alkaloids were determined in ergot sclerotia isolated from rye grains. Total content was nearly 0.01% (97.9 mg/kg). However, the alkaloid profile was dominated by ergocristine at 45.6% (44.7 mg/kg), an alkaloid not commonly found in the tested food products. Ergocorninine at 0.2% (0.2 mg/kg) was the least abundant alkaloid. PMID:27904328

Enhancing overall tensile and compressive response of pure Mg using nano-TiB{sub 2} particulates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meenashisundaram, Ganesh Kumar; Seetharaman, Sankaranarayanan; Gupta, Manoj, E-mail: mpegm@nus.edu.sg

2014-08-15

A novel attempt is made to synthesize and study the isolated effects of less than two volume fraction TiB{sub 2} nanoparticulates (60 nm) on pure magnesium. New light weight Mg–TiB{sub 2} nanocomposites with superior mechanical properties compared to pure magnesium are synthesized using disintegrated melt deposition technique followed by hot extrusion. The microstructural characterization studies revealed that the samples exhibited fairly uniform distribution of TiB{sub 2} nanoparticulates with minimal porosity and good interfacial integrity between Mg matrix and TiB{sub 2} particulates. The coefficient of thermal expansion results indicates that the addition of 0.58, 0.97, and 1.98 vol.% TiB{sub 2} nanoparticulatesmore » marginally improves the dimensional stability of pure magnesium. A significant improvement in the room temperature tensile properties of pure magnesium was observed with the addition of less than two volume fraction TiB{sub 2} nanoparticulates. The synthesized Mg 1.98 vol.% TiB{sub 2} nanocomposite revealed the best room temperature tensile properties with a significant increase in the 0.2% tensile yield strength by ∼ 54%, ultimate tensile strength by ∼ 15% and fracture strain by ∼ 79% when compared to pure Mg. The X-ray diffraction studies indicated changes in the basal plane orientation of pure Mg with the addition of nano-TiB{sub 2} particulates. A maximum tensile fracture strain of ∼ 16% is achieved with the addition of 0.97 vol.% TiB{sub 2}. The room temperature compressive properties of the nanocomposites reveal that the addition of 1.98 TiB{sub 2} increases the 0.2% compressive yield strength of Mg by ∼ 47% and ultimate compressive strength by ∼ 10% with a marginal increase in the fracture strain (∼ 11%). Reduction in tensile–compression yield asymmetry was observed for Mg 0.58 and 0.97 vol.% TiB{sub 2} nanocomposites which can be attributed to the weakening of the strong basal texture of pure Mg. - Highlights: • First attempt is made to synthesize and characterize Mg-TiB{sub 2} nanocomposites. • XRD studies indicate nano TiB{sub 2} addition modifies the basal texture of pure Mg. • Maximum tensile fracture strain of ∼ 16 % in Mg 0.97 vol.% TiB{sub 2} nanocomposite. • Hardness values of Mg-TiB{sub 2} composites indicate superior tribological properties.« less

Denitrification in the karstic Floridan Aquifer

NASA Astrophysics Data System (ADS)

Fork, M.; Albertin, A. R.; Heffernan, J. B.; Katz, B. G.; Cohen, M. J.

2010-12-01

Nitrate concentrations in the karstic Floridan Aquifer have increased dramatically over the past 50 years, owing to agricultural intensification and urbanization. Due to low concentrations of organic matter and moderately oxic conditions in the Floridan Aquifer, groundwater denitrification has been assumed to be negligible. In this study, we evaluate that assumption using both existing and new data describing dissolved gases (Ne, N2, O2, Ar) and NO3- concentration and isotopic composition (δ18O- and δ15N-NO3) in the aquifer’s artesian springs. For new data, we collected samples from 33 spring vents representing a gradient of both DO and NO3- concentrations in northern Florida and used Membrane Inlet Mass Spectrometry (MIMS) to directly measure dissolved N2 and Ar. We modeled the physical processes (recharge temperature, dissolution of excess air) driving super-saturation of N2 gas using Ne and Ar where data describing Ne were available. Ar concentrations were correlated closely with recharge temperature, which ranged from 15.7 - 22.2°C, while Ne was closely correlated with excess air, which ranged from 1.05 to 2.66 mg L-1 and averaged 1.83 mg L-1. Estimates of physical mechanisms allowed calculation of expected N2 concentrations that were compared to observed N2 concentrations. Where Ne data were unavailable, we assumed excess air equal to the empirical average. Overall, observed N2 exceeded expectations based on physical processes in 33 of 47 cases; average excess N2 was 0.48 mg L-1 across all sites. In addition, excess N2 was negatively correlated with DO (r2 = 0.46); springs with low DO (<2.5 mg L-1) had an average of 0.84 mg L-1 excess N2 while springs with higher DO contain little to no excess N2 (0.04 mg L-1). In addition, excess N2 was positively correlated with δ15N-NO3-. These observations are consistent with the widespread occurrence of denitrification in the Floridan Aquifer. Low DOC concentrations indicate that alternative electron donors may fuel nitrate reduction. Scaling to regional estimates of N2 production based on springs discharge and DO concentrations indicates that subsurface denitrification may account for some of the imbalance in springshed nutrient budgets. In addition, we conclude that use of δ15N-NO3- to diagnose isotope sourcing may be conflated by fractionation of aquifer nitrate pools by denitrification.

The Effects of Magnesium Supplementation on Subjective Anxiety and Stress—A Systematic Review

PubMed Central

Boyle, Neil Bernard; Lawton, Clare; Dye, Louise

2017-01-01

Background: Anxiety related conditions are the most common affective disorders present in the general population with a lifetime prevalence of over 15%. Magnesium (Mg) status is associated with subjective anxiety, leading to the proposition that Mg supplementation may attenuate anxiety symptoms. This systematic review examines the available evidence for the efficacy of Mg supplementation in the alleviation of subjective measures of anxiety and stress. Methods: A systematic search of interventions with Mg alone or in combination (up to 5 additional ingredients) was performed in May 2016. Ovid Medline, PsychInfo, Embase, CINAHL and Cochrane databases were searched using equivalent search terms. A grey literature review of relevant sources was also undertaken. Results: 18 studies were included in the review. All reviewed studies recruited samples based upon an existing vulnerability to anxiety: mildly anxious, premenstrual syndrome (PMS), postpartum status, and hypertension. Four/eight studies in anxious samples, four/seven studies in PMS samples, and one/two studies in hypertensive samples reported positive effects of Mg on subjective anxiety outcomes. Mg had no effect on postpartum anxiety. No study administered a validated measure of subjective stress as an outcome. Conclusions: Existing evidence is suggestive of a beneficial effect of Mg on subjective anxiety in anxiety vulnerable samples. However, the quality of the existing evidence is poor. Well-designed randomised controlled trials are required to further confirm the efficacy of Mg supplementation. PMID:28445426

Thin-Film Photoluminescent Properties and the Atomistic Model of Mg2TiO4 as a Non-rare Earth Matrix Material for Red-Emitting Phosphor

NASA Astrophysics Data System (ADS)

Huang, Chieh-Szu; Chang, Ming-Chuan; Huang, Cheng-Liang; Lin, Shih-kang

2016-12-01

Thin-film electroluminescent devices are promising solid-state lighting devices. Red light-emitting phosphor is the key component to be integrated with the well-established blue light-emitting diode chips for stimulating natural sunlight. However, environmentally hazardous rare-earth (RE) dopants, e.g. Eu2+ and Ce2+, are commonly used for red-emitting phosphors. Mg2TiO4 inverse spinel has been reported as a promising matrix material for "RE-free" red light luminescent material. In this paper, Mg2TiO4 inverse spinel is investigated using both experimental and theoretical approaches. The Mg2TiO4 thin films were deposited on Si (100) substrates using either spin-coating with the sol-gel process, or radio frequency sputtering, and annealed at various temperatures ranging from 600°C to 900°C. The crystallinity, microstructures, and photoluminescent properties of the Mg2TiO4 thin films were characterized. In addition, the atomistic model of the Mg2TiO4 inverse spinel was constructed, and the electronic band structure of Mg2TiO4 was calculated based on density functional theory. Essential physical and optoelectronic properties of the Mg2TiO4 luminance material as well as its optimal thin-film processing conditions were comprehensively reported.

The Effects of Magnesium Supplementation on Subjective Anxiety and Stress-A Systematic Review.

PubMed

Boyle, Neil Bernard; Lawton, Clare; Dye, Louise

2017-04-26

Anxiety related conditions are the most common affective disorders present in the general population with a lifetime prevalence of over 15%. Magnesium (Mg) status is associated with subjective anxiety, leading to the proposition that Mg supplementation may attenuate anxiety symptoms. This systematic review examines the available evidence for the efficacy of Mg supplementation in the alleviation of subjective measures of anxiety and stress. A systematic search of interventions with Mg alone or in combination (up to 5 additional ingredients) was performed in May 2016. Ovid Medline, PsychInfo, Embase, CINAHL and Cochrane databases were searched using equivalent search terms. A grey literature review of relevant sources was also undertaken. 18 studies were included in the review. All reviewed studies recruited samples based upon an existing vulnerability to anxiety: mildly anxious, premenstrual syndrome (PMS), postpartum status, and hypertension. Four/eight studies in anxious samples, four/seven studies in PMS samples, and one/two studies in hypertensive samples reported positive effects of Mg on subjective anxiety outcomes. Mg had no effect on postpartum anxiety. No study administered a validated measure of subjective stress as an outcome. Existing evidence is suggestive of a beneficial effect of Mg on subjective anxiety in anxiety vulnerable samples. However, the quality of the existing evidence is poor. Well-designed randomised controlled trials are required to further confirm the efficacy of Mg supplementation.

Hardness, function, emotional well-being, satisfaction and the overall sexual experience in men using 100-mg fixed-dose or flexible-dose sildenafil citrate

PubMed Central

Ströberg, P; Kaminetsky, J C; Park, N C; Goldfischer, E R; Creanga, D L; Stecher, V J

2010-01-01

The prescribing information for sildenafil citrate (VIAGRA, Pfizer, New York, NY, USA) recommends flexible dosing (50 mg initially, adjusted to 100 or 25 mg based on effectiveness and tolerability) in most men with erectile dysfunction (ED). In many men, however, 100 mg may be the most appropriate initial dose because it would reduce the need for titration and could prevent discouragement and treatment abandonment should 50 mg be insufficient. Results of two previously published double-blind, placebo-controlled sildenafil trials of similar design except for a fixed-dose vs flexible-dose regimen were analyzed. Relative to the flexible-dose, approximately one-third more men were satisfied with an initial and fixed dose of 100 mg. In addition, tolerability was similar, and improvements from baseline in outcomes on validated, ED-specific, patient-reported questionnaires were either similar (erectile function and the percentage of completely hard and fully rigid erections) or greater (emotional well-being and the overall sexual experience). The similarity in outcomes is not surprising given that almost 90% of the men in the flexible-dose trial titrated to 100 mg after 2 weeks. These data suggest prescription of an initial dose of 100 mg for men with ED, except in those for whom it is inappropriate. PMID:20596083

Molecular cloning, characterization and expression profiles of thioredoxin 1 and thioredoxin 2 genes in Mytilus galloprovincialis

NASA Astrophysics Data System (ADS)

Wang, Qing; Ning, Xuanxuan; Pei, Dong; Zhao, Jianmin; You, Liping; Wang, Chunyan; Wu, Huifeng

2013-05-01

Thioredoxin (Trx) proteins are involved in many biological processes especially the regulation of cellular redox homeostasis. In this study, two Trx cDNAs were cloned from the mussel Mytilus galloprovincialis using rapid amplifi cation of cDNA ends-polymerase chain reaction (RACE-PCR). The two cDNAs were named MgTrx1 and MgTrx2, respectively. The open reading frames of MgTrx1 and MgTrx2 were 318 and 507 base pairs (bp) and they encoded proteins of 105 and 168 amino acids with estimated molecular masses of 11.45 and 18.93 kDa, respectively. Sequence analysis revealed that both proteins possessed the conserved active site dithiol motif Cys-Gly-Pro-Cys. In addition, MgTrx2 also possessed a putative mitochondrial targeting signal suggesting that it is located in the mitochondria. Quantitative real-time polymerase chain reaction (qPCR) revealed that both MgTrx1 and MgTrx2 were constitutively expressed in all tissues examined. The MgTrx1 transcript was most abundant in hemocytes and gills, whereas the MgTrx2 transcript was most abundant in gonad, hepatopancreas, gill and hemocytes. Following Vibrio anguillarum challenge, the expression of MgTrx1 was up-regulated and reached its peak, at a value 10-fold the initial value, at 24 h. Subsequently, expression returned back to the original level. In contrast, the expression level of MgTrx2 was down-regulated following bacterial stimulation, with one fi fth of the control level evident at 12 h post challenge. These results suggest that MgTrx1 and MgTrx2 may play important roles in the response of M. galloprovincialis to bacterial challenge.

Highly efficient removal of ammonia nitrogen from wastewater by dielectrophoresis-enhanced adsorption.

PubMed

Liu, Dongyang; Cui, Chenyang; Wu, Yanhong; Chen, Huiying; Geng, Junfeng; Xia, Jianxin

2018-01-01

A new approach, based on dielectrophoresis (DEP), was developed in this work to enhance traditional adsorption for the removal of ammonia nitrogen (NH 3 -N) from wastewater. The factors that affected the removal efficiency were systematically investigated, which allowed us to determine optimal operation parameters. With this new method we found that the removal efficiency was significantly improved from 66.7% by adsorption only to 95% by adsorption-DEP using titanium metal mesh as electrodes of the DEP and zeolite as the absorbent material. In addition, the dosage of the absorbent/zeolite and the processing time needed for the removal were greatly reduced after the introduction of DEP into the process. In addition, a very low discharge concentration (C, 1.5 mg/L) of NH 3 -N was achieved by the new method, which well met the discharge criterion of C < 8 mg/L (the emission standard of pollutants for rare earth industry in China).

Factors Affecting Oxidation of Thiosalts by Thiobacilli

PubMed Central

Silver, M.; Dinardo, O.

1981-01-01

The effects of temperature, initial pH, and the concentrations of ammonium, phosphate, and heavy metals on the oxidation of thiosalts by an authentic strain of Thiobacillus thiooxidans (ATCC 8085) and by a mixed culture isolated from a base metal-processing mill effluent pond were studied. The optimum temperature was 30°C and the optimum initial pH was 3.75 for both cultures using thiosulfate and for the mixed culture using tetrathionate. T. thiooxidans ATCC 8085 did not oxidize tetrathionate. For a thiosalt concentration of 2,000 ppm (2,000 mg/liter), maximal rates of destruction occurred at concentrations of ammonium ion above 2 mg/liter and in the presence of 1 mg of phosphate per liter. Under optimal conditions, the rate of thiosulfate oxidation by the pure culture was 55 ± 3 mg/liter per h; the mixed culture oxidized thiosulfate at the rate of 40 ± 1 mg/liter per h and tetrathionate at the rate of 50 ± 2 mg/liter per h. Metal ions caused normal inhibition kinetics in the oxidation of thiosulfate by T. thiooxidans ATCC 8085. Ki values were calculated for cadmium (16 mg/liter), copper (0.46 mg/liter), lead (2 mg/liter), silver (3.1 mg/liter), and zinc (33 mg/liter). Only a slight additive effect was apparent in the presence of all of these metal ions. The mixed culture of thiosalt-oxidizing bacteria was less sensitive to heavy metal inhibition; the order of inhibition of thiosulfate oxidation was Cd < Zn < Pb < Ag < Cu, and that of tetrathionate oxidation was Zn < Cd < Pb < Ag < Cu. PMID:16345785

Effect of Copper on Corrosion of Forged AlSi1MgMn Automotive Suspension Components

NASA Astrophysics Data System (ADS)

Koktas, Serhan; Gokcil, Emre; Akdi, Seracettin; Birol, Yucel

2017-09-01

Recently, modifications in the alloy composition and the manufacturing process cycle were proposed to achieve a more uniform structure with no evidence of coarse grains across the section of the AlSi1MgMn alloys. Cu was added to the AlSi1MgMn alloy to improve its age hardening capacity without a separate solution heat treatment. However, Cu addition degrades the corrosion resistance of this alloy due to the formation of Al-Cu precipitates along the grain boundaries that are cathodic with respect to the aluminum matrix and thus encourage intergranular corrosion. The present work was undertaken to identify the impact of Cu addition on the corrosion properties of AlSi1MgMn alloys with different Cu contents. A series of AlSi1MgMn alloys with 0.06-0.89 wt.% Cu were tested in order to identify an optimum level of Cu addition.

Reduced Graphene Oxide Coating with Anticorrosion and Electrochemical Property-Enhancing Effects Applied in Hydrogen Storage System.

PubMed

Du, Yi; Li, Na; Zhang, Tong-Ling; Feng, Qing-Ping; Du, Qian; Wu, Xing-Hua; Huang, Gui-Wen

2017-08-30

Low-capacity retention is the most prominent problem of the magnesium nickel alloy (Mg 2 Ni), which prevents it from being commercially applied. Here, we propose a practical method for enhancing the cycle stability of the Mg 2 Ni alloy. Reduced graphene oxide (rGO) possesses a graphene-based structure, which could provide high-quality barriers that block the hydroxyl in the aqueous electrolyte; it also possesses good hydrophilicity. rGO has been successfully coated on the amorphous-structured Mg 2 Ni alloy via electrostatic assembly to form the rGO-encapsulated Mg 2 Ni alloy composite (rGO/Mg 2 Ni). The experimental results show that ζ potentials of rGO and the modified Mg 2 Ni alloy are totally opposite in water, with values of -11.0 and +22.4 mV, respectively. The crumpled structure of rGO sheets and the contents of the carbon element on the surface of the alloy are measured using scanning electron microscopy, transmission electron microscopy, and energy dispersive spectrometry. The Tafel polarization test indicates that the rGO/Mg 2 Ni system exhibits a much higher anticorrosion ability against the alkaline solution during charging/discharging. As a result, high-capacity retentions of 94% (557 mAh g -1 ) at the 10th cycle and 60% (358 mAh g -1 ) at the 50th cycle have been achieved, which are much higher than the results on Mg 2 Ni capacity retention combined with the absolute value reported so far to our knowledge. In addition, both the charge-transfer reaction rate and the hydrogen diffusion rate are proven to be boosted with the rGO encapsulation. Overall, this work demonstrates the effective anticorrosion and electrochemical property-enhancing effects of rGO coating and shows its applicability in the Mg-based hydrogen storage system.

Is there a relationship between hypomagnesemia and proton-pump inhibitors in patients on chronic hemodialysis?

PubMed

Mikolasevic, I; Milic, S; Stimac, D; Zaputovic, L; Lukenda Zanko, V; Gulin, T; Jakopcic, I; Klaric, D; Gulin, M; Orlic, L

2016-05-01

We investigated the association among long-term proton-pump inhibitors (PPIs) use with serum magnesium (Mg) levels in chronic hemodialysis (HD) patients, as well as possible association among PPI use and increased risk of cardiovascular (CVD) morbidity in HD patients. Of 418 HD patients that were screened for inclusion, 136 were excluded due to incomplete medical data, duration of renal replacement therapy (RRT) for less than 12months, use of Mg-based-phosphate binders or other Mg-based medications or either to presence of chronic increased GI losses. Among 282 patients included in the study, 170 patients were on PPIs. Serum Mg levels were significantly lower among PPI users vs. non-users (0.94±0.2 vs. 1.03±0.2mmol/L; p<0.0001). The median duration of PPI use was 27±9.6months (range from 12 to 108) and it was not significantly associated with Mg levels (r=0.116; p=0.167). Additionally, residual renal function didn't show a significant correlation with Mg concentration (r=-0.102; p=NS) in both groups of patients. The use of PPIs was an independent and strong predictor of low Mg concentrations even in multivariate analysis (OR 3.05; 95% CI 1.2498-7.4594, p=0.01). On the other hand, the daily dose of PPIs was not associated with low Mg levels. PPI users had a higher rate of adverse CVD events during the 1 year of follow-up in comparison to non-PPI users but that difference wasn't statistically significant (17.6% vs. 10.7%; p=0.110). We have found a significant association between PPI use and lower serum Mg levels in chronic HD patients. Copyright © 2016 European Federation of Internal Medicine. Published by Elsevier B.V. All rights reserved.

Competition Between Co(NH3)63+ and Inner Sphere Mg2+ Ions in the HDV Ribozyme

PubMed Central

Gong, Bo; Chen, Jui-Hui; Bevilacqua, Philip C.; Golden, Barbara L.; Carey, Paul R.

2009-01-01

Divalent cations play critical structural and functional roles in many RNAs. While the hepatitis delta virus (HDV) ribozyme can undergo self-cleavage in the presence of molar concentrations of monovalent cations, divalent cations such as Mg2+ are required for efficient catalysis under physiological conditions. Moreover, the cleavage reaction can be inhibited with Co(NH3)63+, an analog of Mg(H2O)62+. Here, the binding of Mg2+ and Co(NH3)63+ to the HDV ribozyme are studied by Raman microscopic analysis of crystals. Raman difference spectra acquired at different metal ion conditions reveal changes in the ribozyme. When Mg2+ alone is introduced to the ribozyme, inner sphere coordination of Mg(H2O)x2+ (x≤5) to non-bridging PO2− oxygen, and changes in base stretches and phosphodiester group conformation are observed. In addition, binding of Mg2+ induces deprotonation of a cytosine assigned to the general acid C75, consistent with solution studies. When Co(NH3)63+ alone is introduced, deprotonation of C75 is again observed, as are distinctive changes in base vibrational ring modes and phosphodiester backbone conformation. In contrast to Mg2+ binding, Co(NH3)63+ binding does not perturb PO2− group vibrations, consistent with its ability to make only outer sphere contacts. Surprisingly, competitive binding studies reveal that Co(NH3)63+ ions displace some inner sphere-coordinated magnesium species, including ions coordinated to PO2− groups or the N7 of a guanine, likely G1 at the active site. These observations contrast with the tenet that Co(NH3)63+ ions displace only outer sphere magnesium ions. Overall, our data support two classes of inner sphere Mg2+-PO2− binding sites: sites that Co(NH3)63+ can displace, and others it cannot. PMID:19888753

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luo, Sin-Jie; Su, Yen-Hao Frank; Lu, Muh-Jung

In this study, the effect of magnesium addition on the inclusion formation in SS400 steel was investigated. The experimental specimens with and without Mg addition treatment were compared. The microstructure was observed using optical microscopy after etching with 3% nital. The morphology and chemical composition of the inclusions were analyzed via scanning electron microscopy and energy dispersive spectrometry. The lattice structure and orientation of the inclusions were identified by electron backscattering diffraction. The average size of inclusions in SS400 was between 0.67 and 0.75 μm, and between 0.65 and 0.68 μm in SS400 + Mg. The 2 ppm Mg additionmore » resulted in the oxide formation change from Al{sub 2}O{sub 3} to MgO·Al{sub 2}O{sub 3} and in the inclusion formation change from Al{sub 2}O{sub 3}–MnS to MgO·Al{sub 2}O{sub 3}–MnS. Moreover, a simple-phase MnS with an average grain size of 1 μm to 2 μm was observed in rod-like, globular, and polyhedron forms. - Highlights: • The effect of magnesium addition was investigated for SS400 steel. • 2 ppm Mg addition changes the inclusion formation from Al2O3-MnS to MgO·Al2O3-MnS. • MnS observed in inclusions exhibits rod-like, globular, and polyhedron forms.« less

Effect of Nanoparticles on the Morphology, Thermal, and Electrical Properties of Low-Density Polyethylene after Thermal Aging

PubMed Central

Wang, Youyuan; Zhang, Zhanxi; Xiao, Kun

2017-01-01

This paper investigates the morphology, thermal, and electrical properties of LDPE (low-density polyethylene)-based nanocomposites after thermal aging. The FTIR (Fourier transform infrared spectroscopy) spectra results show that thermo-oxidative reactions occur in neat LDPE and LDPE/SiO2 nanocomposites when the aging time is 35 days and in LDPE/MgO nanocomposites when the aging time is 77 days. Specifically, LDPE/MgO nanocomposites delay the appearance of thermo-oxidative reactions, showing anti-thermal aging ability. Furthermore, nanocomposites present lower onset degradation temperature than neat LDPE, showing better thermal stabilization. With regard to the electrical properties, nanocomposites maintain the ability to suppress space charge accumulation after thermal aging. Additionally, in comparison with SiO2 nanocomposites and neat LDPE, the permittivity of LDPE/MgO nanocomposites changes slightly after thermal aging. It is concluded that LDPE/MgO nanocomposites have better insulation properties than neat LDPE after thermal aging, which may be caused by the interface introduced by the nanoparticles. PMID:29023428

Effect of Nanoparticles on the Morphology, Thermal, and Electrical Properties of Low-Density Polyethylene after Thermal Aging.

PubMed

Wang, Youyuan; Wang, Can; Zhang, Zhanxi; Xiao, Kun

2017-10-12

This paper investigates the morphology, thermal, and electrical properties of LDPE (low-density polyethylene)-based nanocomposites after thermal aging. The FTIR (Fourier transform infrared spectroscopy) spectra results show that thermo-oxidative reactions occur in neat LDPE and LDPE/SiO₂ nanocomposites when the aging time is 35 days and in LDPE/MgO nanocomposites when the aging time is 77 days. Specifically, LDPE/MgO nanocomposites delay the appearance of thermo-oxidative reactions, showing anti-thermal aging ability. Furthermore, nanocomposites present lower onset degradation temperature than neat LDPE, showing better thermal stabilization. With regard to the electrical properties, nanocomposites maintain the ability to suppress space charge accumulation after thermal aging. Additionally, in comparison with SiO₂ nanocomposites and neat LDPE, the permittivity of LDPE/MgO nanocomposites changes slightly after thermal aging. It is concluded that LDPE/MgO nanocomposites have better insulation properties than neat LDPE after thermal aging, which may be caused by the interface introduced by the nanoparticles.

Effective adsorption of malachite green using magnetic barium phosphate composite from aqueous solution

NASA Astrophysics Data System (ADS)

Zhang, Fan; Wei, Zhong; Zhang, Wanning; Cui, Haiyan

2017-07-01

Magnetic Ba3(PO4)2/Fe3O4-nanoparticle (called BPFN) was prepared, characterized, and developed as a low-cost adsorbent for malachite green (MG) from aqueous solution. Factors such as adsorption temperature, pH of solution, dosage of adsorbent, adsorption kinetics and isotherms were investigated. The maximum adsorption capacity obtained in this work was 1639 mg g- 1 at 45 °C and pH 6. The adsorption process fitted the pseudo-first-order kinetic model and Langmuir isotherm model. Evidences from zeta potential, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS) data revealed that the adsorption process was driven by electrostatic attraction, the interaction between Lewis base sbnd N(CH3)2 in MG and Lewis acid Ba sites of BPFN. In addition, the BPFN could be easily regenerated by a magnet and the adsorption capacity maintained at 70% after five cycles. The present study suggests that the BPFN had high potential of removing MG from wastewater.

The fracture resistance of 1420 and 1421 Al-Mg-Li alloys

NASA Technical Reports Server (NTRS)

Birt, M. J.; Hafley, R. A.; Wagner, J. A.; Lisagor, W. B.

1993-01-01

The resistance to stable crack growth in 1420-T6 (Al-5Mg-2.1Li-0.1Zr-0.01Sc, less than 0.06Fe, in wt pct) and 1421-T6 (Al-4.7Mg-1.9Li-0.09Zr-0.2Sc, less than 0.06Fe) Al-Mg-Li alloys was investigated, based on the R curves generated in accordance with ASTM E561-86 and fractography analyses. The crack resistance of 1420 and 1421 alloys was found to be comparable to that of the conventional Space Shuttle External Tank Al alloy, 2219-T87. The main differences in the fracture behaviors arose from differences in the alloys' microstructures. In the case of 1420 alloy, a slightly enhanced toughness behavior was observed, due to the T-phase precipitates, which may have promoted more homogeneous deformation and enhanced microvoid coalescence. In the case of 1421 alloy, the addition of Sc led to a refined grain size and resulted in slightly reduced toughness.

Fabrication of near-net shape graphite/magnesium composites for large mirrors

NASA Astrophysics Data System (ADS)

Wendt, Robert; Misra, Mohan

1990-10-01

Successful development of space-based surveillance and laser systems will require large precision mirrors which are dimensionally stable under thermal, static, and dynamic (i.e., structural vibrations and retargeting) loading conditions. Among the advanced composites under consideration for large space mirrors, graphite fiber reinforced magnesium (Gr/Mg) is an ideal candidate material that can be tailored to obtain an optimum combination of properties, including a high modulus of elasticity, zero coefficient of thermal expansion, low density, and high thermal conductivity. In addition, an innovative technique, combining conventional filament winding and vacuum casting has been developed to produce near-net shape Gr/Mg composites. This approach can significantly reduce the cost of fabricating large mirrors by decreasing required machining. However, since Gr/Mg cannot be polished to a reflective surface, plating is required. This paper will review research at Martin Marietta Astronautics Group on Gr/Mg mirror blank fabrication and measured mechanical and thermal properties. Also, copper plating and polishing methods, and optical surface characteristics will be presented.

Laboratory evaluation of traditionally used plant-based insect repellent against the malaria vector Anopheles arabiensis Patton (Diptera: Culicidae).

PubMed

Karunamoorthi, Kaliyaperumal; Ilango, Kandan; Murugan, Kadarkarai

2010-04-01

A laboratory study was carried out to evaluate the repellent efficacy of a methanol-leaf extract of Ethiopian traditionally used insect repellent plant viz., Lomi sar [vernacular name (local native language, Amharic); Cymbopogon citratus (DC) Stapf. (Poaceae)] against Anopheles arabiensis at four different concentrations viz., 1.0, 1.5, 2.0, and 2.5 mg/cm(2). The percentage protection in relation to the dose method was performed. C. citratus extract has shown various degrees of repellency impact against A. arabiensis. It provided the maximum total percentage protection of 78.83% at 2.5 mg/cm(2) and followed 68.06% at 2.0 mg/cm(2) for 12 h. All four tested concentrations of C. citratus extract offered significant protection and Student's t test results shows statistically significant (p value = 0.001) [1.0 mg/cm(2) (t = 22.89; df = 4); 1.5 mg/cm(2) (t = 24.03; df = 4); 2.0 mg/cm(2) (t = 36.92; df = 4); 2.5 mg/cm(2) (t = 22.31; df = 4)] difference between treated and control groups. The result suggests that it could serve as a potent insect repellent against vectors of disease. Globally, C. citratus is renowned for its therapeutic values. Above and beyond, due to its user- as well as environmental-friendly nature, it should be promoted among the marginalized populations in order to reduce man-vector contact. In addition, this appropriate strategy affords the opportunity to minimize chemical repellent usage and the risks associated with adverse side effects. At the end of the day, traditionally used plant-based insect repellents could be viable safer alternative sources for chemical insect repellents.

Behavior of bone cells in contact with magnesium implant material.

PubMed

Burmester, Anna; Willumeit-Römer, Regine; Feyerabend, Frank

2017-01-01

Magnesium-based implants exhibit several advantages, such as biodegradability and possible osteoinductive properties. Whether the degradation may induce cell type-specific changes in metabolism still remains unclear. To examine the osteoinductivity mechanisms, the reaction of bone-derived cells (MG63, U2OS, SaoS2, and primary human osteoblasts (OB)) to magnesium (Mg) was determined. Mg-based extracts were used to mimic more realistic Mg degradation conditions. Moreover, the influence of cells having direct contact with the degrading Mg metal was investigated. In exposure to extracts and in direct contact, the cells decreased pH and osmolality due to metabolic activity. Proliferating cells showed no significant reaction to extracts, whereas differentiating cells were negatively influenced. In contrast to extract exposure, where cell size increased, in direct contact to magnesium, cell size was stable or even decreased. The amount of focal adhesions decreased over time on all materials. Genes involved in bone formation were significantly upregulated, especially for primary human osteoblasts. Some osteoinductive indicators were observed for OB: (i) an increased cell count after extract addition indicated a higher proliferation potential; (ii) increased cell sizes after extract supplementation in combination with augmented adhesion behavior of these cells suggest an early switch to differentiation; and (iii) bone-inducing gene expression patterns were determined for all analyzed conditions. The results from the cell lines were inhomogeneous and showed no specific stimulus of Mg. The comparison of the different cell types showed that primary cells of the investigated tissue should be used as an in vitro model if Mg is analyzed. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 165-179, 2017. © 2015 Wiley Periodicals, Inc.

A rapid micro quantification method of paracetamol in suppositories using differential scanning calorimetry.

PubMed

Noordin, Mohamed I; Chung, L Y

2004-01-01

This study adopts Differential Scanning Calorimetry (DSC) to analyze the thermal properties of samples (2.5-4.0 mg) from the tip, middle, and base sections of individual paracetamol suppositories, which were sampled carefully using a stainless steel scalpel. The contents of paracetamol present in the samples obtained from these sections were determined from the enthalpies of fusion of paracetamol and expressed as % w/w paracetamol to allow comparison of the amount of paracetamol found in each section. The tip, middle, and base sections contained 10.1+/-0.2%, 10.1+/-0.2%, and 10.3+/-0.2% w/w paracetamol, and are statistically similar (One-way anova; p>0.05). This indicates that the preparation technique adopted produces high quality suppositories in terms of content uniformity. The contents of paracetamol in the 120-mg paracetamol suppositories determined by DSC and UV spectrophotometry were statistically equivalent (Students's t-test; p>0.05), 120.8+/-2.6 mg and 120.8+/-1.5 mg, respectively, making DSC a clear alternative method for the measurement of content of drug in suppositories. The main advantages of the method are that samples of only 2.5-4.0 mg are required and the procedure does not require an extraction process, which allows for the analysis to be completed rapidly. In addition, it is highly sensitive and reproducible, with the lower detection limit at 4.0% w/w paracetamol, which is about 2.5 times lower than the content of paracetamol (10% w/w) present in our 120-mg paracetamol suppositories and commercial paracetamol suppositories, which contained about 125 mg paracetamol. Therefore, this method is particularly suited for determination of content uniformity in individual suppositories in quality control (QC) and in process quality control (PQC).

The addition of tramadol as a second opioid may improve pain relief in severe osteoarthritis: a prospective study.

PubMed

Di Lorenzo, Luigi; Foti, Calogero; Forte, Alfonso Maria; Palmieri, Enzo; Formisano, Rita; Vatakencherry, Abraham; Pappagallo, Marco

2010-01-01

Opioid combination has been shown to reduce the need for escalating doses for the treatment of cancer pain. A prospective study was planned to evaluate the addition of tramadol to a stronger opioid for the treatment of severe pain as a result of osteoarthritis, previously uncontrolled by non-opioid analgesics or weak opioids. All subjects received tramadol 200 mg and tizanidine 2 mg. At 2 weeks, tramadol was discontinued for patients still reporting poor pain relief (effectiveness ≤50%), and a stronger opioid was titrated to a morphine equivalent amount (MEA) of 40-60 mg orally. After two additional weeks, patients were then divided into two groups: the Strong Opioid Group (SO) and the Tramadol plus the Strong Opioid Group (TSO). The SO group was allowed to escalate opioid dose for lack of effectiveness; the TSO group received tramadol 150 mg daily, thereafter additional strong opioid titration was allowed. A total of 74 patients were studied: SO (n = 40) and TSOG (n = 34). All patients eventually achieved pain relief quality, with both groups reporting similar Karnofsky Performance Scale effectiveness. The SO group achieved satisfactory pain relief (>50%) at an average daily oral MEA of 120 mg. TSO subjects achieved satisfactory pain relief (>50%) at an average daily oral MEA of 95 mg. The addition of tramadol provided a synergistic effect resulting in a 30-mg decrease in necessary morphine equivalents with fewer opioid-related adverse effects. © 2010 The Authors. Pain Practice © 2010 World Institute of Pain.

Enhanced Production of Acarbose and Concurrently Reduced Formation of Impurity C by Addition of Validamine in Fermentation of Actinoplanes utahensis ZJB-08196

PubMed Central

Xue, Ya-Ping; Qin, Jun-Wei; Wang, Ya-Jun; Wang, Yuan-Shan; Zheng, Yu-Guo

2013-01-01

Commercial production of acarbose is exclusively via done microbial fermentation with strains from the genera of Actinoplanes. The addition of C7N-aminocyclitols for enhanced production of acarbose and concurrently reduced formation of impurity C by cultivation of A. utahensis ZJB-08196 in 500-mL shake flasks was investigated, and validamine was found to be the most effective strategy. Under the optimal conditions of validamine addition, acarbose titer was increased from 3560 ± 128 mg/L to 4950 ± 156 mg/L, and impurity C concentration was concurrently decreased from 289 ± 24 mg/L to 107 ± 29 mg/L in batch fermentation after 168 h of cultivation. A further fed-batch experiment coupled with the addition of validamine (20 mg/L) in the fermentation medium prior to inoculation was designed to enhance the production of acarbose. When twice feedings of a mixture of 6 g/L glucose, 14 g/L maltose, and 9 g/L soybean flour were performed at 72 h and 96 h, acarbose titer reached 6606 ± 103 mg/L and impurity C concentration was only 212 ± 12 mg/L at 168 h of cultivation. Acarbose titer and proportion of acarbose/impurity C increased by 85.6% and 152.9% when compared with control experiments. This work demonstrates for the first time that validamine addition is a simple and effective strategy for increasing acarbose production and reducing impurity C formation. PMID:23484146

Effect of Cr and Mn addition and heat treatment on AlSi3Mg casting alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tocci, Marialaura, E-mail: m.tocci@unibs.it

In the present paper the effect of heat treatment on an AlSi3Mg alloy with and without Cr and Mn addition was investigated. Beside the well-known modification of the morphology of Fe-containing intermetallics, it was found that Cr and Mn allowed the formation of dispersoids in the aluminium matrix after solution heat treatment at 545 °C, as shown by scanning transmission electron microscope observations. These particles were responsible of the enhanced Vickers microhardness of the aluminium matrix in comparison with the base alloy after solution treatment and quenching, according to dispersion hardening mechanism. The presence of these particles was not affectedmore » by ageing treatment, which instead allowed the precipitation of β-Mg{sub 2}Si, as shown by the elaboration of differential scanning calorimeter curves. The formation of dispersoids and the study of their effect on mechanical properties can represent an interesting development for applications at high temperatures of casting alloys due to their thermal stability compared to other strengthening phases as β-Mg{sub 2}Si. - Highlights: •Cr and Mn successfully modified the morphology of Fe-containing intermetallics. •Cr- and Mn-dispersoids formed in the aluminium matrix during solution treatment. •Dispersion hardening was detected after solution treatment for Cr-containing alloy. •The dispersion hardening effect was maintained after ageing treatment.« less

Determination of Mycotoxin Production of Fusarium Species in Genetically Modified Maize Varieties by Quantitative Flow Immunocytometry.

PubMed

Bánáti, Hajnalka; Darvas, Béla; Fehér-Tóth, Szilvia; Czéh, Árpád; Székács, András

2017-02-22

Levels of mycotoxins produced by Fusarium species in genetically modified (GM) and near-isogenic maize, were determined using multi-analyte, microbead-based flow immunocytometry with fluorescence detection, for the parallel quantitative determination of fumonisin B1, deoxynivalenol, zearalenone, T-2, ochratoxin A, and aflatoxin B1. Maize varieties included the genetic events MON 810 and DAS-59122-7 , and their isogenic counterparts. Cobs were artificially infested by F. verticillioides and F. proliferatum conidia, and contained F. graminearum and F. sporotrichoides natural infestation. The production of fumonisin B1 and deoxynivalenol was substantially affected in GM maize lines: F. verticillioides , with the addition of F. graminearum and F. sporotrichoides , produced significantly lower levels of fumonisin B1 (~300 mg·kg -1 ) in DAS-59122-7 than in its isogenic line (~580 mg·kg -1 ), while F. proliferatum , in addition to F. graminearum and F. sporotrichoides , produced significantly higher levels of deoxynivalenol (~18 mg·kg -1 ) in MON 810 than in its isogenic line (~5 mg·kg -1 ). Fusarium verticillioides , with F. graminearum and F. sporotrichoides , produced lower amounts of deoxynivalenol and zearalenone than F. proliferatum , with F. graminearum and F. sporotrichoides . T-2 toxin production remained unchanged when considering the maize variety. The results demonstrate the utility of the Fungi-Plex™ quantitative flow immunocytometry method, applied for the high throughput parallel determination of the target mycotoxins.

Characterization of hydraulic fracturing flowback water in Colorado: Implications for water treatment

USGS Publications Warehouse

Lester, Yaal; Ferrer, Imma; Thurman, E. Michael; Sitterley, Kurban A.; Korak, Julie A.; Aiken, George R.; Linden, Karl G.

2015-01-01

A suite of analytical tools was applied to thoroughly analyze the chemical composition of an oil/gas well flowback water from the Denver–Julesburg (DJ) basin in Colorado, and the water quality data was translated to propose effective treatment solutions tailored to specific reuse goals. Analysis included bulk quality parameters, trace organic and inorganic constituents, and organic matter characterization. The flowback sample contained salts (TDS = 22,500 mg/L), metals (e.g., iron at 81.4 mg/L) and high concentration of dissolved organic matter (DOC = 590 mgC/L). The organic matter comprised fracturing fluid additives such as surfactants (e.g., linear alkyl ethoxylates) and high levels of acetic acid (an additives' degradation product), indicating the anthropogenic impact on this wastewater. Based on the water quality results and preliminary treatability tests, the removal of suspended solids and iron by aeration/precipitation (and/or filtration) followed by disinfection was identified as appropriate for flowback recycling in future fracturing operations. In addition to these treatments, a biological treatment (to remove dissolved organic matter) followed by reverse osmosis desalination was determined to be necessary to attain water quality standards appropriate for other water reuse options (e.g., crop irrigation). The study provides a framework for evaluating site-specific hydraulic fracturing wastewaters, proposing a suite of analytical methods for characterization, and a process for guiding the choice of a tailored treatment approach.

The unintended energy impacts of increased nitrate contamination from biofuels production.

PubMed

Twomey, Kelly M; Stillwell, Ashlynn S; Webber, Michael E

2010-01-01

Increases in corn cultivation for biofuels production, due to the Energy Independence and Security Act of 2007, are likely to lead to increases in nitrate concentrations in both surface and groundwater resources in the United States. These increases might trigger the requirement for additional energy consumption for water treatment to remove the nitrates. While these increasing concentrations of nitrate might pose a human health concern, most water resources were found to be within current maximum contaminant level (MCL) limits of 10 mg L(-1) NO(3)-N. When water resources exceed this MCL, energy-intensive drinking water treatment is required to reduce nitrate levels below 10 mg L(-1). Based on prior estimates of water supplies currently exceeding the nitrate MCL, we calculate that advanced drinking water treatment might require an additional 2360 million kWh annually (for nitrate affected areas only)--a 2100% increase in energy requirements for water treatment in those same areas--to mitigate nitrate contamination and meet the MCL requirement. We predict that projected increases in nitrate contamination in water may impact the energy consumed in the water treatment sector, because of the convergence of several related trends: (1) increasing cornstarch-based ethanol production, (2) increasing nutrient loading in surface water and groundwater resources as a consequence of increased corn-based ethanol production, (3) additional drinking water sources that exceed the MCL for nitrate, and (4) potentially more stringent drinking water standards for nitrate.

Improvement of Cycling Performance of Lithium-Sulfur Batteries by Using Magnesium Oxide as a Functional Additive for Trapping Lithium Polysulfide.

PubMed

Ponraj, Rubha; Kannan, Aravindaraj G; Ahn, Jun Hwan; Kim, Dong-Won

2016-02-17

Trapping lithium polysulfides formed in the sulfur positive electrode of lithium-sulfur batteries is one of the promising approaches to overcome the issues related to polysulfide dissolution. In this work, we demonstrate that intrinsically hydrophilic magnesium oxide (MgO) nanoparticles having surface hydroxyl groups can be used as effective additives to trap lithium polysulfides in the positive electrode. MgO nanoparticles were uniformly distributed on the surface of the active sulfur, and the addition of MgO into the sulfur electrode resulted in an increase in capacity retention of the lithium-sulfur cell compared to a cell with pristine sulfur electrode. The improvement in cycling stability was attributed to the strong chemical interactions between MgO and lithium polysulfide species, which suppressed the shuttling effect of lithium polysulfides and enhanced the utilization of the sulfur active material. To the best of our knowledge, this report is the first demonstration of MgO as an effective functional additive to trap lithium polysulfides in lithium-sulfur cells.

Reduction of nitrate in aquifer microcosms by carbon additions

USGS Publications Warehouse

Obenhuber, Donald C.; Lowrance , Richard

1991-01-01

Aquifer microcosms were used to examine the effects of NO−3 and C amendments on groundwater from the Claiborne aquifer. Nitrate concentrations of 12.17 mg L−1 in aquifer microcosms were reduced 0.92%/d to 5.84 mg L−1 by the addition of 10 mg C L−1 for 35 d. Nitrate disappearance correlated with increases in number of denitrifiers and dissolved N2O concentration and decreases in dissolved oxygen, suggesting biological denitrification. Nitrate/chloride ratios decreased in microcosms with 10 mg C L−1 added and then increased when the C addition was removed. Carbon additions of 0.4 mg C L−1 had no effect on the microbial or chemical properties of the microcosms. Nitrous oxide levels in wells sampling the Claiborne aquifer showed an increase with depth, indicating N2O production within the aquifer. Microcosms are useful tools to examine biological transformations of chemical contaminants in unconsolidated aquifer material. The remediation of NO−3 contaminated aquifers by organic infusion is possible and appears to be a function of microbial denitrification.

A Commercial Conducting Polymer as Both Binder and Conductive Additive for Silicon Nanoparticle-Based Lithium-Ion Battery Negative Electrodes.

PubMed

Higgins, Thomas M; Park, Sang-Hoon; King, Paul J; Zhang, Chuanfang John; McEvoy, Niall; Berner, Nina C; Daly, Dermot; Shmeliov, Aleksey; Khan, Umar; Duesberg, Georg; Nicolosi, Valeria; Coleman, Jonathan N

2016-03-22

This work describes silicon nanoparticle-based lithium-ion battery negative electrodes where multiple nonactive electrode additives (usually carbon black and an inert polymer binder) are replaced with a single conductive binder, in this case, the conducting polymer PSS. While enabling the production of well-mixed slurry-cast electrodes with high silicon content (up to 95 wt %), this combination eliminates the well-known occurrence of capacity losses due to physical separation of the silicon and traditional inorganic conductive additives during repeated lithiation/delithiation processes. Using an in situ secondary doping treatment of the PSS with small quantities of formic acid, electrodes containing 80 wt % SiNPs can be prepared with electrical conductivity as high as 4.2 S/cm. Even at the relatively high areal loading of 1 mg/cm(2), this system demonstrated a first cycle lithiation capacity of 3685 mA·h/g (based on the SiNP mass) and a first cycle efficiency of ∼78%. After 100 repeated cycles at 1 A/g this electrode was still able to store an impressive 1950 mA·h/g normalized to Si mass (∼75% capacity retention), corresponding to 1542 mA·h/g when the capacity is normalized by the total electrode mass. At the maximum electrode thickness studied (∼1.5 mg/cm(2)), a high areal capacity of 3 mA·h/cm(2) was achieved. Importantly, these electrodes are based on commercially available components and are produced by the standard slurry coating methods required for large-scale electrode production. Hence, the results presented here are highly relevant for the realization of commercial LiB negative electrodes that surpass the performance of current graphite-based negative electrode systems.

Poly (3,4-ethylenedioxythiophene) graphene oxide composite coatings for controlling magnesium implant corrosion.

PubMed

Catt, Kasey; Li, Huaxiu; Cui, X Tracy

2017-01-15

Magnesium (Mg) is a promising biodegradable implant material because of its appropriate mechanical properties and safe degradation products. However, in vivo corrosion speed and hydrogen gas production need to be controlled for uses in biomedical applications. Here we report the development of a conducting polymer 3,4-ethylenedioxythiphene (PEDOT) and graphene oxide (GO) composite coating as a corrosion control layer. PEDOT/GO was electropolymerized on Mg samples in ethanol media. The coated Mg samples were subjected to various corrosion tests. The PEDOT/GO coating significantly reduced the rate of corrosion as evidenced by lower Mg ion concentration and pH of the corrosion media. In addition, the coating decreased the evolved hydrogen. Electrochemical analysis of the corroding samples showed more positive corrosion potential, a decreased corrosion current, and an increase in the polarization resistance. PEDOT/GO corrosion protection is attributed to three factors; an initial passive layer preventing solution ingress, buildup of negative charges in the film, and formation of corrosion protective Mg phosphate layer through redox coupling with Mg corrosion. To explore the biocompatibility of the coated implants in vitro, corrosion media from PEDOT/GO coated or uncoated Mg samples were exposed to cultured neurons where PEDOT/GO coated samples showed decreased toxicity. These results suggest that PEDOT/GO coating will be an effective treatment for controlling corrosion of Mg based medical implants. Coating Mg substrates with a PEDOT/GO composite coating showed a significant decrease in corrosion rate. While conducting polymer coatings have been used to prevent corrosion on various metals, there has been little work on the use of these coatings for Mg. Additionally, to our knowledge, there has not been a report of the combined used of conducting polymer and GO as a corrosion control layer. Corrosion control is attributed to an initial barrier layer followed by electrochemical coupling of the PEDOT/GO coating with the substrate to facilitate the formation of a protective phosphate layer. This coupling also resulted in a decrease in hydrogen produced during corrosion, which could further improve the host tissue integration of Mg implants. This work elaborates on the potential for electroactive polymers to serve as corrosion control methods. Copyright © 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Synthesis, characterization and biological evaluation of strontium/magnesium-co-substituted hydroxyapatite.

PubMed

Geng, Zhen; Wang, Renfeng; Li, Zhaoyang; Cui, Zhenduo; Zhu, Shengli; Liang, Yanqin; Liu, Yunde; Huijing, Bao; Li, Xue; Huo, Qianyu; Liu, Zhili; Yang, Xianjin

2016-07-01

The present study aims to investigate the contribution of two biologically important cations, Mg(2+) and Sr(2+), when co-substituted into the structure of hydroxyapatite (Ca10(PO4)6(OH)2, HA). The substituted samples were synthesized by a hydrothermal method that involved the addition of Mg(2+) and Sr(2+) containing precursors to partially replace Ca(2+) in the apatite structure. Four co-substituted HA samples with different concentrations of Mg(2+) and Sr(2+) ((Mg + Sr)/(Mg + Sr + Ca) = 30%) were investigated, and they were compared with pure HA. Experimental results showed that only a limited amount of Mg (Mg/(Mg + Ca + Sr) < 14%) could successfully substitute for Ca in HA. In addition, Mg substitution resulted in reduced crystallinity, thermal stability and lattice parameters of HA. In contrast, Sr could fully substitute for Ca. Furthermore, the addition of Sr increased the lattice parameters of HA. Here, we obtained the cation leach liquor by immersing the prepared samples in a culture medium for cell experiments. The in vitro study showed that 10Mg20Sr promoted better MG63 cell attachment, proliferation and differentiation than HA. Thus, the presence of an appropriate proportion of Mg and Sr could play a significant role in the increased biocompatibility of HA. © The Author(s) 2016.

Search for promising compositions for developing new multiphase casting alloys based on Al-Cu-Mg matrix using thermodynamic calculations and mathematic simulation

NASA Astrophysics Data System (ADS)

Zolotorevskii, V. S.; Pozdnyakov, A. V.; Churyumov, A. Yu.

2012-11-01

A calculation-experimental study is carried out to improve the concept of searching for new alloying systems in order to develop new casting alloys using mathematical simulation methods in combination with thermodynamic calculations. The results show the high effectiveness of the applied methods. The real possibility of selecting the promising compositions with the required set of casting and mechanical properties is exemplified by alloys with thermally hardened Al-Cu and Al-Cu-Mg matrices, as well as poorly soluble additives that form eutectic components using mainly the calculation study methods and the minimum number of experiments.

Bacterial-based systems for expression and purification of recombinant Lassa virus proteins of immunological relevance

PubMed Central

Branco, Luis M; Matschiner, Alex; Fair, Joseph N; Goba, Augustine; Sampey, Darryl B; Ferro, Philip J; Cashman, Kathleen A; Schoepp, Randal J; Tesh, Robert B; Bausch, Daniel G; Garry, Robert F; Guttieri, Mary C

2008-01-01

Background There is a significant requirement for the development and acquisition of reagents that will facilitate effective diagnosis, treatment, and prevention of Lassa fever. In this regard, recombinant Lassa virus (LASV) proteins may serve as valuable tools in diverse antiviral applications. Bacterial-based systems were engineered for expression and purification of recombinant LASV nucleoprotein (NP), glycoprotein 1 (GP1), and glycoprotein 2 (GP2). Results Full-length NP and the ectodomains of GP1 and GP2 were generated as maltose-binding protein (MBP) fusions in the Rosetta strains of Escherichia coli (E. coli) using pMAL-c2x vectors. Average fusion protein yields per liter of culture for MBP-NP, MBP-GP1, and MBP-GP2 were 10 mg, 9 mg, and 9 mg, respectively. Each protein was captured from cell lysates using amylose resin, cleaved with Factor Xa, and purified using size-exclusion chromatography (SEC). Fermentation cultures resulted in average yields per liter of 1.6 mg, 1.5 mg, and 0.7 mg of purified NP, GP1 and GP2, respectively. LASV-specific antibodies in human convalescent sera specifically detected each of the purified recombinant LASV proteins, highlighting their utility in diagnostic applications. In addition, mouse hyperimmune ascitic fluids (MHAF) against a panel of Old and New World arenaviruses demonstrated selective cross reactivity with LASV proteins in Western blot and enzyme-linked immunosorbent assay (ELISA). Conclusion These results demonstrate the potential for developing broadly reactive immunological assays that employ all three arenaviral proteins individually and in combination. PMID:18538016

Multicentre phase II studies evaluating imatinib plus hydroxyurea in patients with progressive glioblastoma

PubMed Central

Reardon, D A; Dresemann, G; Taillibert, S; Campone, M; van den Bent, M; Clement, P; Blomquist, E; Gordower, L; Schultz, H; Raizer, J; Hau, P; Easaw, J; Gil, M; Tonn, J; Gijtenbeek, A; Schlegel, U; Bergstrom, P; Green, S; Weir, A; Nikolova, Z

2009-01-01

Background: We evaluated the efficacy of imatinib mesylate in addition to hydroxyurea in patients with recurrent glioblastoma (GBM) who were either on or not on enzyme-inducing anti-epileptic drugs (EIAEDs). Methods: A total of 231 patients with GBM at first recurrence from 21 institutions in 10 countries were enrolled. All patients received 500 mg of hydroxyurea twice a day. Imatinib was administered at 600 mg per day for patients not on EIAEDs and at 500 mg twice a day if on EIAEDs. The primary end point was radiographic response rate and secondary end points were safety, progression-free survival at 6 months (PFS-6), and overall survival (OS). Results: The radiographic response rate after centralised review was 3.4%. Progression-free survival at 6 months and median OS were 10.6% and 26.0 weeks, respectively. Outcome did not appear to differ based on EIAED status. The most common grade 3 or greater adverse events were fatigue (7%), neutropaenia (7%), and thrombocytopaenia (7%). Conclusions: Imatinib in addition to hydroxyurea was well tolerated among patients with recurrent GBM but did not show clinically meaningful anti-tumour activity. PMID:19904263

A hybrid process of biofiltration of secondary effluent followed by ozonation and short soil aquifer treatment for water reuse.

PubMed

Zucker, I; Mamane, H; Cikurel, H; Jekel, M; Hübner, U; Avisar, D

2015-11-01

The Shafdan reclamation project facility (Tel Aviv, Israel) practices soil aquifer treatment (SAT) of secondary effluent with hydraulic retention times (HRTs) of a few months to a year for unrestricted agricultural irrigation. During the SAT, the high oxygen demand (>40 mg L(-1)) of the infiltrated effluent causes anoxic conditions and mobilization of dissolved manganese from the soil. An additional emerging problem is the occurrence of persistent trace organic compounds (TrOCs) in reclaimed water that should be removed prior to reuse. An innovative hybrid process based on biofiltration, ozonation and short SAT with ∼22 d HRT is proposed for treatment of the Shafdan secondary effluent to overcome limitations of the existing system and to reduce the SAT's physical footprint. Besides efficient removal of particulate matter to minimize clogging, coagulation/flocculation and filtration (5-6 m h(-1)) operated with the addition of hydrogen peroxide as an oxygen source efficiently removed dissolved organic carbon (DOC, to 17-22%), ammonium and nitrite. This resulted in reduced effluent oxygen demand during infiltration and oxidant (ozone) demand during ozonation by 23 mg L(-1) and 1.5 mg L(-1), respectively. Ozonation (1.0-1.2 mg O3 mg DOC(-1)) efficiently reduced concentrations of persistent TrOCs and supplied sufficient dissolved oxygen (>30 mg L(-1)) for fully oxic operation of the short SAT with negligible Mn(2+) mobilization (<50 μg L(-1)). Overall, the examined hybrid process provided DOC reduction of 88% to a value of 1.2 mg L(-1), similar to conventional SAT, while improving the removal of TrOCs and efficiently preventing manganese dissolution. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thiolated chitosan: development and in vivo evaluation of an oral delivery system for leuprolide.

PubMed

Iqbal, Javed; Shahnaz, Gul; Perera, Glen; Hintzen, Fabian; Sarti, Federica; Bernkop-Schnürch, Andreas

2012-01-01

The aim of the present study was to develop an oral delivery system for the peptide drug leuprolide. Gel formulations based on unmodified chitosan/reduced glutathione (GSH) and chitosan-thioglycolic acid (chitosan-TGA)/GSH were prepared, and their effect on the absorption of leuprolide was evaluated in vitro and in vivo in male Sprague Dawley rats. Transport studies were performed with freshly excised rat intestinal mucosa mounted in Ussing-type chambers. Due to the addition of gel formulations comprising 0.5% (m/v) unmodified chitosan/0.5% (m/v) GSH and 0.5% (m/v) chitosan-TGA/0.5% (m/v) GSH, the transport of leuprolide across excised mucosa was improved up to 2.06-fold and 3.79-fold, respectively, in comparison with leuprolide applied in buffer (P(app)=2.87 ± 0.77 × 10⁻⁶ cm/s). In vivo, the addition of oral gel formulation comprising 8 mg of unmodified chitosan, 1mg of GSH and 1mg of leuprolide increased the area under the plasma concentration-time curve (AUC₀₋₈) of leuprolide 1.39-fold in comparison with leuprolide having been administered just in saline. Moreover, the administration of oral gel formulation comprising 8 mg of chitosan-TGA, 1mg of GSH and 1mg of leuprolide resulted in a further enhanced leuprolide plasma concentration, and the area under the plasma concentration-time curve (AUC₀₋₈) of leuprolide was increased 3.72-fold in comparison with the control. With the oral gel formulation comprising 8 mg of chitosan-TGA, a relative bioavailability (versus s.c. injection) of 4.5% was achieved in contrast to the control displaying a relative bioavailability of 1.2%. Thus, according to the achieved results, it is suggested that chitosan-TGA in combination with GSH is a valuable tool for improving the oral bioavailability of the peptide drug leuprolide. Copyright © 2011 Elsevier B.V. All rights reserved.

Reducing hole transporter use and increasing perovskite solar cell stability with dual-role polystyrene microgel particles.

PubMed

Chen, Mu; Mokhtar, Muhamad Z; Whittaker, Eric; Lian, Qing; Hamilton, Bruce; O'Brien, Paul; Zhu, Mingning; Cui, Zhengxing; Haque, Saif A; Saunders, Brian R

2017-07-20

Perovskite solar cells (PSCs) are a disruptive technology that continues to attract considerable attention due to their remarkable and sustained power conversion efficiency increase. Improving PSC stability and reducing expensive hole transport material (HTM) usage are two aspects that are gaining increased attention. In a new approach, we investigate the ability of insulating polystyrene microgel particles (MGs) to increase PSC stability and replace the majority of the HTM phase. MGs are sub-micrometre crosslinked polymer particles that swell in a good solvent. The MGs were prepared using a scalable emulsion polymerisation method. Mixed HTM/MG dispersions were subsequently spin-coated onto PSCs and formed composite HTM-MG layers. The HTMs employed were poly(triaryl amine) (PTAA), poly(3-hexylthiophene) (P3HT) and Spiro-MeOTAD (Spiro). The MGs formed mechanically robust composite HTMs with PTAA and P3HT. In contrast, Spiro-MG composites contained micro-cracks due the inability of the relatively small Spiro molecules to interdigitate. The efficiencies for the PSCs containing PTAA-MG and P3HT-MG decreased by only ∼20% compared to control PSCs despite PTAA and P3HT being the minority phases. They occupied only ∼35 vol% of the composite HTMs. An unexpected finding from the study was that the MGs dispersed well within the PTAA matrix. This morphology aided strong quenching of the CH 3 NH 3 PbI 3-x Cl x fluorescence. In addition, the open circuit voltages for the PSCs prepared using P3HT-MG increased by ∼170 mV compared to control PSCs. To demonstrate their versatility the MGs were also used to encapsulate P3HT-based PSCs. Solar cell stability data for the latter as well as those for PSCs containing composite HTM-MG were both far superior compared to data measured for a control PSC. Since MGs can reduce conjugated polymer use and increase stability they have good potential as dual-role PSC additives.

The solidification behavior of calcium oxide-aluminum oxide slags

NASA Astrophysics Data System (ADS)

Prapakorn, Kritsada

The binary CaO-Al2O3 based slag and the ternary CaO-Al2O3-MgO based slag are common slags covering and inclusions that are found in calcium treated Al-killed, continuously cast steels. However, the effect of cooling conditions and chemistry on the solidification behavior of these slags is not well characterized. To better understand this phenomena, the solidification behavior of these slags was studied by using double hot thermocouple technique. TTT and CCT diagrams of these slags were determined to quantify the solidification behavior in both dry and humid atmospheres. In this work, these slag samples were easily undercooled and the solidification behavior of these slags was found to be a strong function of cooling conditions. The crystallization tendency of these slags follows the trends suggested by the phase diagram. In CaO-Al2O3 based slags, The eutectic composition (50%CaO) give the lowest crystallization tendency due to the lowest liquidus temperature. In a eutectic CaO-Al2O3 slag sample, dissolved water in the sample increases crystallization tendency and enhances the growth. It was also found that the crystalline phase that formed during cooling in both the dry and humid conditions is the mixture between 3CaO.Al2O 3 and CaO.Al2O3 phases. In CaO-Al2O3-MgO based slags, the crystallization tendency increases with MgO content because the high MgO content leads to the high liquidus temperature. The effect of dissolved of water on the crystallization of CaO-Al2O3-MgO based slags is not as prominent as in the eutectic CaO-Al2O3 slag. Thus, the addition of MgO to CaO-Al2O3 slags was seen to minimize or eliminate the effect of humidity on the solidification of CaO-Al2O3 based slags. In this work, Uhlmann's method was used to estimate the solid-liquid interfacial energy of CaO-Al2O3 based slag for the temperature between 1100--1250°C. The result is between 0.25--0.4 Joules/m 2.

Preliminary study of the characteristics of a high Mg containing Al-Mg-Si alloy

NASA Astrophysics Data System (ADS)

Yan, F.; McKay, B. J.; Fan, Z.; Chen, M. F.

2012-01-01

An Al-20Mg-4Si high Mg containing alloy has been produced and its characteristics investigated. The as-cast alloy revealed primary Mg2Si particles evenly distributed throughout an α-Al matrix with a β-Al3Mg2 fully divorced eutectic phase observed in interdendritic regions. The Mg2Si particles displayed octahedral, truncated octahedral, and hopper morphologies. Additions of Sb, Ti and Zr had a refining influence reducing the size of the Mg2Si from 52 ± 4 μm to 25 ± 0.1 μm, 35 ± 1 μm and 34 ± 1 μm respectively. HPDC tensile test samples could be produced with a 0.6 wt.% Mn addition which prevented die soldering. Solution heating for 1 hr was found to dissolve the majority of the Al3Mg2 eutectic phase with no evidence of any effect on the primary Mg2Si. Preliminary results indicate that the heat treatment has a beneficial effect on the elongation and the UTS.

Transparent and stretchable strain sensors based on metal nanowire microgrids for human motion monitoring

NASA Astrophysics Data System (ADS)

Cho, Ji Hwan; Ha, Sung-Hun; Kim, Jong-Man

2018-04-01

Optical transparency is increasingly considered as one of the most important characteristics required in advanced stretchable strain sensors for application in body-attachable systems. In this paper, we present an entirely solution-processed fabrication route to highly transparent and stretchable resistive strain sensors based on silver nanowire microgrids (AgNW-MGs). The AgNW-MG strain sensors are readily prepared by patterning the AgNWs on a stretchable substrate into a MG geometry via a mesh-template-assisted contact-transfer printing. The MG has a unique architecture comprising the AgNWs and can be stretched to ɛ = 35%, with high gauge factors of ˜6.9 for ɛ = 0%-30% and ˜41.1 for ɛ = 30%-35%. The sensor also shows a high optical transmittance of 77.1% ± 1.5% (at 550 nm) and stably maintains the remarkable optical performance even at high strains. In addition, the sensor responses are found to be highly reversible with negligible hysteresis and are reliable even under repetitive stretching-releasing cycles (1000 cycles at ɛ = 10%). The practicality of the AgNW-MG strain sensor is confirmed by successfully monitoring a wide range of human motions in real time after firmly laminating the device onto various body parts.

Thymic pathologies in myasthenia gravis: a preoperative assessment of CAT scan and nuclear based imaging.

PubMed

Jordan, Berit; Kellner, Juliane; Jordan, Karin; Bähre, Manfred; Behrmann, Curd; Zierz, Stephan

2016-04-01

Precise diagnostic work up of a suspected thymic pathology in patients with myasthenia gravis (MG) is very important for potential surgical implications and further disease course. In this study the diagnostic value of combined preoperative radiological (CAT scan) and nuclear based imaging (octreotide and thallium scintigraphy) in patients with MG was evaluated. Twenty four patients were included. Histopathology revealed thymoma in nine patients, thymic carcinoma (TC) in one patient, lymphofollicular hyperplasia in seven patients, and involuted thymus in another seven patients. Diagnostic sensitivity for detecting thymoma/TC was 80 % in CAT scan as well as in somatostatin scintigraphy; the combination of both procedures reached 90 %. However, the diagnostic specifity to exclude thymoma in CAT scan was 100 % and in octreotide scintigraphy 85.7 %. Semiquantitative octreotide uptake significantly correlated with histological grading of thymoma/TC (r = 0.764) and histological proliferation rate Ki67 (r = 0.894). Thallium scintigraphy was positive only in one out of four thymoma cases. In this study, somatostatin scintigraphy has been shown to be a useful additional diagnostic technique in detecting thymic malignancies in patients with MG. These results might be especially helpful in patients with late onset MG as these patients are in general no candidates for thymectomy.

Effects of suvorexant, an orexin receptor antagonist, on sleep parameters as measured by polysomnography in healthy men.

PubMed

Sun, Hong; Kennedy, William P; Wilbraham, Darren; Lewis, Nicole; Calder, Nicole; Li, Xiaodong; Ma, Junshui; Yee, Ka Lai; Ermlich, Susan; Mangin, Eric; Lines, Christopher; Rosen, Laura; Chodakewitz, Jeffrey; Murphy, Gail M

2013-02-01

Suvorexant (MK-4305) is an orexin receptor antagonist being developed for the treatment of insomnia. This report describes the effects of nighttime administration of suvorexant on polysomnography (PSG) sleep parameters in healthy young men. Randomized, double-blind, placebo-controlled, 4-period crossover PSG study, followed by an additional 5(th) period to assess pharmacokinetics. Sleep laboratory. Healthy young men between 18 and 45 years of age (22 enrolled, 19 completed). Periods 1-4: suvorexant (10 mg, 50 mg, or 100 mg) or placebo 1 h before nighttime PSG recording. Period 5: suvorexant 10 mg, 50 mg, or 100 mg. In Periods 1-4, overnight sleep parameters were recorded by PSG and next-morning residual effects were assessed by psychomotor performance tests and subjective assessments. Statistically significant sleep-promoting effects were observed with all doses of suvorexant compared to placebo. Suvorexant 50 mg and 100 mg significantly decreased latency to persistent sleep and wake after sleep onset time, and increased sleep efficiency. Suvorexant 10 mg significantly decreased wake after sleep onset time. There were no statistically significant effects of suvorexant on EEG frequency bands including delta (slow wave) activity based on power spectral analysis. Suvorexant was well tolerated. There was no evidence of next-day residual effects for suvorexant 10 mg. Suvorexant 50 mg statistically significantly reduced subjective alertness, and suvorexant 100 mg significantly increased reaction time and reduced subjective alertness. There were no statistically significant effects of any suvorexant dose on digit symbol substitution test performance. In Period 5, plasma samples of suvorexant were collected for pharmacokinetic evaluation. The median T(max) was 3 hours and apparent terminal t(½) was 9-13 hours. In healthy young men without sleep disorders, suvorexant promoted sleep with some evidence of residual effects at the highest doses.

Contrast-enhanced spectral mammography vs. mammography and MRI - clinical performance in a multi-reader evaluation.

PubMed

Fallenberg, Eva M; Schmitzberger, Florian F; Amer, Heba; Ingold-Heppner, Barbara; Balleyguier, Corinne; Diekmann, Felix; Engelken, Florian; Mann, Ritse M; Renz, Diane M; Bick, Ulrich; Hamm, Bernd; Dromain, Clarisse

2017-07-01

To compare the diagnostic performance of contrast-enhanced spectral mammography (CESM) to digital mammography (MG) and magnetic resonance imaging (MRI) in a prospective two-centre, multi-reader study. One hundred seventy-eight women (mean age 53 years) with invasive breast cancer and/or DCIS were included after ethics board approval. MG, CESM and CESM + MG were evaluated by three blinded radiologists based on amended ACR BI-RADS criteria. MRI was assessed by another group of three readers. Receiver-operating characteristic (ROC) curves were compared. Size measurements for the 70 lesions detected by all readers in each modality were correlated with pathology. Reading results for 604 lesions were available (273 malignant, 4 high-risk, 327 benign). The area under the ROC curve was significantly larger for CESM alone (0.84) and CESM + MG (0.83) compared to MG (0.76) (largest advantage in dense breasts) while it was not significantly different from MRI (0.85). Pearson correlation coefficients for size comparison were 0.61 for MG, 0.69 for CESM, 0.70 for CESM + MG and 0.79 for MRI. This study showed that CESM, alone and in combination with MG, is as accurate as MRI but is superior to MG for lesion detection. Patients with dense breasts benefitted most from CESM with the smallest additional dose compared to MG. • CESM has comparable diagnostic performance (ROC-AUC) to MRI for breast cancer diagnostics. • CESM in combination with MG does not improve diagnostic performance. • CESM has lower sensitivity but higher specificity than MRI. • Sensitivity differences are more pronounced in dense and not significant in non-dense breasts. • CESM and MRI are significantly superior to MG, particularly in dense breasts.

Determination of Mg(2+) Speciation in a TFSI(-)-Based Ionic Liquid With and Without Chelating Ethers Using Raman Spectroscopy.

PubMed

Watkins, Tylan; Buttry, Daniel A

2015-06-11

Raman spectroscopy was employed to assess the complex environment of magnesium salts in the n-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (BMPyrTFSI) room-temperature ionic liquid (RTIL). At room temperature, Mg(TFSI)2 was miscible with BMPyrTFSI and formulated by [Mg(TFSI)2](x)[BMPyrTFSI](1-x) (x ≤ 0.55). Results suggest that at low concentrations of Mg(TFSI)2, anionic complexes in which Mg(2+) is surrounded by at least four TFSI(-) were formed. Above x = 0.2 an average of three TFSI(-) surround each Mg(2+). Below x = 0.12, there is a greater number of monodentate interactions between TFSI(-) oxygens and Mg(2+) cations, whereas above x = 0.12 bidentate ligands dominate. The fraction of TFSI(-) existing in the cis conformation increased with increasing Mg(2+) concentration. Mg(ClO4)2 was also studied as a Mg(2+) source. At equivalent mole fractions to those of the Mg(TFSI)2 salt, Mg(2+) from Mg(ClO4)2 was surrounded by only two TFSI(-) anions as ClO4(-) appeared to compete with TFSI(-) for coordination with Mg(2+). Similar behavior was also observed for the less soluble halide salts MgX2 (X = Cl, Br, I). Additions of chelating ligands were shown to effectively reduce the average number of TFSI(-) around Mg(2+) in a manner consistent with maintaining a sixfold oxygen coordination number around Mg(2+). Furthermore, an alternative class of ionic liquids, known as "solvate" ionic liquids, were produced. In this case glymes (Gm, m + 1 ether oxygens) were mixed with Mg(TFSI)2 so that glymes chelated Mg(2+), creating Mg(Gm)(y)(2+) complexes. The general formula was given by Mg(Gm)(y)(TFSI)2. These solvate ILs melt between 40 and 80 °C. Raman spectra clearly showed the glyme chelating ability and stronger coordination with Mg(2+) with respect to TFSI(-). Finally, linear sweep voltammograms showed the anodic stability of the glymes to improve due to coordination with Mg(2+).

Combination of multiple model population analysis and mid-infrared technology for the estimation of copper content in Tegillarca granosa

NASA Astrophysics Data System (ADS)

Hu, Meng-Han; Chen, Xiao-Jing; Ye, Peng-Chao; Chen, Xi; Shi, Yi-Jian; Zhai, Guang-Tao; Yang, Xiao-Kang

2016-11-01

The aim of this study was to use mid-infrared spectroscopy coupled with multiple model population analysis based on Monte Carlo-uninformative variable elimination for rapidly estimating the copper content of Tegillarca granosa. Copper-specific wavelengths were first extracted from the whole spectra, and subsequently, a least square-support vector machine was used to develop the prediction models. Compared with the prediction model based on full wavelengths, models that used 100 multiple MC-UVE selected wavelengths without and with bin operation showed comparable performances with Rp (root mean square error of Prediction) of 0.97 (14.60 mg/kg) and 0.94 (20.85 mg/kg) versus 0.96 (17.27 mg/kg), as well as ratio of percent deviation (number of wavelength) of 2.77 (407) and 1.84 (45) versus 2.32 (1762). The obtained results demonstrated that the mid-infrared technique could be used for estimating copper content in T. granosa. In addition, the proposed multiple model population analysis can eliminate uninformative, weakly informative and interfering wavelengths effectively, that substantially reduced the model complexity and computation time.

Single Event Effects Test Results for Advanced Field Programmable Gate Arrays

NASA Technical Reports Server (NTRS)

Allen, Gregory R.; Swift, Gary M.

2006-01-01

Reconfigurable Field Programmable Gate Arrays (FPGAs) from Altera and Actel and an FPGA-based quick-turnApplication Specific Integrated Circuit (ASIC) from Altera were subjected to single-event testing using heavy ions. Both Altera devices (Stratix II and HardCopy II) exhibited a low latchup threshold (below an LET of 3 MeV-cm2/mg) and thus are not recommended for applications in the space radiation environment. The flash-based Actel ProASIC Plus device did not exhibit latchup to an effective LET of 75 MeV-cm2/mg at room temperature. In addition, these tests did not show flash cell charge loss (upset) or retention damage. Upset characterization of the design-level flip-flops yielded an LET threshold below 10 MeV-cm2/mg and a high LET cross section of about lxlO-6 cm2/bit for storing ones and about lxl0-7 cm2/bit for storing zeros . Thus, the ProASIC device may be suitable for critical flight applications with appropriate triple modular redundancy mitigation techniques.

Dilatometric shrinkage study on magnesium titanate-based ceramic systems

NASA Astrophysics Data System (ADS)

Ermawati, F. U.; Suasmoro, S.

2018-03-01

The development of dielectric materials for applications in the microwave frequencies has been increasing with rapid progress in mobile and satellite communication systems. Magnesium titanate (MgTiO3)-based ceramics have been the favourite candidates for such applications due to their excellent dielectric characteristics, i.e. a moderate level of dielectric constant together with a high-quality factor and high-temperature stability. These outstanding performance, however, can only be achieved when the ceramics are highly dense. The work reported in this paper discussed the study on the dilatometric shrinkage behaviour of pure and zinc-doped magnesium titanate (Mg1–xZn x TiO3 for x = 0–0.5) ceramic systems after the systems following the heating passage up to 1300 °C. The results were discussed based on the phase formation data recorded from powder X-ray diffraction (XRD). An additional 2 wt. % V2O5 to the MZT0.2 system has increased the shrinkage of the system, and hence the relative density. The V2O5 addition also prevented the grain growth and did not alter the structure. From 100 Hz to 20 MHz, the dielectric permittivity is constant; which varies from (15.4 – 17.0) ± 0.1 % throughout the samples, these values are therefore frequency independent.

Improved Synthesis Of Potassium Beta' '-Alumina

NASA Technical Reports Server (NTRS)

Williams, Roger M.; Jeffries-Nakamura, Barbara; Ryan, Margaret A.; O'Connor, Dennis E.; Kisor, Adam; Underwood, Mark

1996-01-01

Improved formulations of precursor materials synthesize nearly-phase-pure potassium beta' '-alumina solid electrolyte (K-BASE) powder. Materials are microhomogeneous powders (or, alternatively, gels) containing K(+,) Mg(2+), and Al(3+). K-BASE powder produced used in potassium-working-fluid alkali-metal thermal-to-electric conversion (K-AMTEC), in which heat-input and heat-rejection temperatures lower than sodium-working-fluid AMTEC (Na-AMTEC). Additional potential use lies in purification of pottassium by removal of sodium and calcium.

Determination of free and total sulfur(IV) compounds in coconut water using high-resolution continuum source molecular absorption spectrometry in gas phase.

PubMed

Oliveira, Michael L; Brandao, Geovani C; de Andrade, Jailson B; Ferreira, Sergio L C

2018-03-01

This work proposes a method for the determination of free and total sulfur(IV) compounds in coconut water samples, using the high-resolution continuum source molecular absorption spectrometry. It is based on the measurement of the absorbance signal of the SO 2 gas generate, which is resultant of the addition of hydrochloric acid solution on the sample containing the sulfating agent. The sulfite bound to the organic compounds is released by the addition of sodium hydroxide solution, before the generation of the SO 2 gas. The optimization step was performed using multivariate methodology involving volume, concentration and flow rate of hydrochloric acid. This method was established by the sum of the absorbances obtained in the three lines of molecular absorption of the SO 2 gas. This strategy allowed a procedure for the determination of sulfite with limits of detection and quantification of 0.36 and 1.21mgL -1 (for a sample volume of 10mL) and precision expressed as relative standard deviation of 5.4% and 6.4% for a coconut water sample containing 38.13 and 54.58mgL -1 of free and total sulfite, respectively. The method was applied for analyzing five coconut water samples from Salvador city, Brazil. The average contents varied from 13.0 to 55.4mgL -1 for free sulfite and from 24.7 to 66.9mgL -1 for total sulfur(IV) compounds. The samples were also analyzed employing the Ripper´s procedure, which is a reference method for the quantification of this additive. A statistical test at 95% confidence level demonstrated that there is no significant difference between the results obtained by the two methods. Copyright © 2017 Elsevier B.V. All rights reserved.

The Impact of Additives on the Phosphorus, Potassium, and Sodium Content of Commonly Consumed Meat, Poultry, and Fish Products Among Patients With Chronic Kidney Disease.

PubMed

Parpia, Arti Sharma; L'Abbé, Mary; Goldstein, Marc; Arcand, Joanne; Magnuson, Bernadene; Darling, Pauline B

2018-03-01

Patients with chronic kidney disease (CKD) are advised to limit their dietary intake of phosphorus and potassium as hyperphosphatemia and hyperkalemia are both associated with an increased risk of mortality. There is uncertainty concerning the actual content of these minerals in the Canadian food supply, as phosphorus and potassium are increasingly being used as food additives. This study aimed to determine the impact of food additives on the chemically analyzed content of phosphorus, potassium, sodium, and protein in commonly consumed meat, poultry, and fish products (MPFs). Foods representing commonly consumed MPF identified by a food frequency questionnaire in dialysis patients were purchased from three major grocery store chains in Canada. MPF with and without phosphorus and potassium additives listed on their ingredient list (n = 76) as well as reference MPF that was additive free (n = 15) were chemically analyzed for phosphorus, potassium, sodium, and protein content according to Association of Analytical Community official methods. Phosphorus, potassium, and sodium additives were present on the ingredient list in 37%, 9%, and 72% of MPF, respectively. Among MPF categories that contained a phosphorus additive, phosphorus content was significantly (P < .05) higher in MPF with phosphorus additives versus MPF without phosphorus additives and MPF reference foods (median [min, max]): (270 [140, 500] mg/100 g) versus (200 [130, 510] mg/100 g) versus (210 [100, 260] mg/100 g), respectively. Among MPF categories containing a potassium additive, foods listing a potassium additive had significantly more (P < .05) potassium than foods that did not list potassium additives and reference foods (900 [750, 1100] mg/100 g) versus (325 [260, 470] mg/100 g) versus (420 [270, 450] mg/100 g). The use of additives in packaged MPF products as indicated by the ingredient list can significantly contribute to the dietary phosphorus and potassium loads in patients with CKD. Patients with CKD should be educated to avoid MPF foods listing phosphorus and/or potassium additives on the ingredient list, which may lead to improved dietary adherence. Copyright © 2017 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Effects of thermal treatment on the Mg{sub x}Zn{sub 1−x}O films and fabrication of visible-blind and solar-blind ultraviolet photodetectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Chunguang; Jiang, Dayong, E-mail: dayongjiangcust@126.com; Tan, Zhendong

Highlights: • Single-phase wurtzite/cubic Mg{sub x}Zn{sub 1−x}O films were grown by RF magnetron sputtering technique. • We focus on the red-shift caused by annealing the Mg{sub x}Zn{sub 1−x}O films. • MSM-structured visible-blind and solar-blind UV photodetectors were fabricated. - Abstract: A series of single-phase Mg{sub x}Zn{sub 1−x}O films with different Mg contents were prepared on quartz substrates by RF magnetron sputtering technique using different MgZnO targets, and annealed under the atmospheric environment. The absorption edges of Mg{sub x}Zn{sub 1−x}O films can cover the whole near ultraviolet and even the whole solar-blind spectra range, and the solar-blind wurtzite/cubic Mg{sub x}Zn{sub 1−x}Omore » films have been realized successfully by the same method. In addition, the absorption edges of annealed films shift to a long wavelength, which is caused by the diffusion of Zn atoms gathering at the surface during the thermal treatment process. Finally, the truly solar-blind metal-semiconductor-metal structured photodetectors based on wurtzite Mg{sub 0.445}Zn{sub 0.555}O and cubic Mg{sub 0.728}Zn{sub 0.272}O films were fabricated. The corresponding peak responsivities are 17 mA/W at 275 nm and 0.53 mA/W at 250 nm under a 120 V bias, respectively.« less

Modeling of the phase evolution in Mg1-xAlxB2 (0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersson, Anders David; Casillas, Luis; Lezama Pacheco, Juan

Despite the chemical and structural simplicity of MgB{sub 2}, at 39 K this compound has the highest known {Tc} of any binary compound. Electron doping by substituting Al for Mg leads to decreasing Tc and the observed concentration dependent rate of decrease has been proposed to arise from the non-ideal character of MgB{sub 2}-AIB{sub 2} solid solutions, which derives from the existence of an ordered Mg{sub 0.5}Al{sub 0.5}B{sub 2} compound. Heterogeneous nano-scale structure patterns in solid solutions have emerged as an important concept for complex materials, ranging from actinide alloys and oxides to high-temperature cuprate superconductors and mallganite-based materials exhibitingmore » colossal magnetoresistivity. In this work we investigate the formation of structural heterogeneities in Mg{sub 1-x}AI{sub x}B{sub 2}, which take the form of nano-scale AI-AI and AI-Mg domains of different geometry and size, using molecular statics/dynamics simulations and in particular we study the corresponding signatures in diffraction experiments. In order to undertake this task we first derive appropriate Mg-AI-B semi-empirical potentials within the Modified Embedded Atom Method formalism. These potentials are also applied to explore the equilibrium Mg{sub 1-x}AI{sub x}B{sub 2} phase diagram for 0 < x < 0.5. Additionally, density functional theory calculations were utilized to study the influence of heterogeneities on the electronic structure and charge distribution in Mg{sub 1-x}AI{sub x}B{sub 2}.« less

Effect of CaO on Hot Workability and Microstructure of Mg-9.5Zn-2Y Alloy

NASA Astrophysics Data System (ADS)

Kwak, Tae-yang; Kim, Daeguen; Yang, Jaehack; Yoon, Young-ok; Kim, Shae K.; Lim, Hyunkyu; Kim, Woo Jin

Mg-Zn-Y system alloys have been a great interest because Mg-Zn-Y alloys with I-phase exhibited high ductility at room and elevated temperatures. According to our preliminary experiments, the addition of CaO improved strength, but the process window became narrow. Therefore, the aim of current work was to find optimum extrusion conditions for CaO added Mg-Zn-Y alloys by processing maps. The 0.3 wt.% of CaO added Mg-9.5Zn-2Y (Mg95.6Zn3.8Y0.6) alloy was prepared by casting into steel mold and homogenizing. Hot compression test were performed in the Gleeble machine at temperature range of 250-400 °C with various strain rates. The alloys were extruded with a reduction ratio of 20:1. To analyze the microstructure and texture, optical micrograph, scanning electron microscope and electron backscattered diffraction were used. Moreover, we investigated the effects of metallic Ca addition in this alloy to compare with the addition of CaO.

Analysis and design of a calcium-based sulfur sorbent for applications in integrated gasification combined cycle energy systems

NASA Astrophysics Data System (ADS)

Hasler, David Johann Ludwig

The reactivity of various Ca-based sorbent materials in pelletized form with H2S or CO2 was investigated at high temperatures (750--880°C). An extensive study was conducted to compare the performance of sorbent pellets derived from plaster of Paris and limestone. Multicycle absorption and regeneration tests showed that plaster-based pellets out performed the limestone-based pellets primarily due to a higher surface area and mesoporosity. The effect of pore-modifiers on the reactivity of limestone with H 2S was investigated by incorporating additives such as cornstarch, graphite and polyvinylalcohol (PVA) in the sorbent. Multicycle sulfidation and regeneration tests of the modified sorbent showed that starch did not improve the reactivity of the limestone, graphite reduced the reactivity, while PVA improved it. The effect of the chemical additives MgO and SrO on the performance of CaO-based sorbent pellets was investigated. The effect of MgO was tested by starting with materials that contained MgCO3 in a natural form, such as dolomite. The effect of SrO was tested by starting with SrCO 3 either co-precipitated with CaCO3 or by wet-mixing SrCO 3 with limestone in slurry form. The MgO was found to improve the thermal stability of the CaO-based sorbent but lowered the overall absorption capacity of the material when reacted with CO2 or H2S, while SrO decreased the thermal stability of the sorbent when it was reacted with CO2; no absorption tests were run with H2S. A study of the performance of pelletized CaO-based cores coated with a refractory material such as alumina and limestone or alumina and kaolin was conducted. The reactivity of the core and shell pellets with H2S was determined. The strength and durability of the pellets were determined by using crushing strength analysis and abrasion resistance tests. Pellets coated with either alumina and limestone or alumina and kaolin proved to be strong and adequate for use in industrial reactors. A semi-empirical mathematical model was developed to represent the reaction of H2S with a sorbent pellet. The model was based on the well-known shrinking core model and it was applied successfully for the analysis of both pellet cores and core and shell pellets reacting with H2S.

Impact of salinity on element incorporation in two benthic foraminiferal species with contrasting magnesium contents

NASA Astrophysics Data System (ADS)

Geerken, Esmee; de Nooijer, Lennart Jan; van Dijk, Inge; Reichart, Gert-Jan

2018-04-01

Accurate reconstructions of seawater salinity could provide valuable constraints for studying past ocean circulation, the hydrological cycle and sea level change. Controlled growth experiments and field studies have shown the potential of foraminiferal Na / Ca as a direct salinity proxy. Incorporation of minor and trace elements in foraminiferal shell carbonate varies, however, greatly between species and hence extrapolating calibrations to other species needs validation by additional (culturing) studies. Salinity is also known to impact other foraminiferal carbonate-based proxies, such as Mg / Ca for temperature and Sr / Ca for sea water carbonate chemistry. Better constraints on the role of salinity on these proxies will therefore improve their reliability. Using a controlled growth experiment spanning a salinity range of 20 units and analysis of element composition on single chambers using laser ablation-Q-ICP-MS, we show here that Na / Ca correlates positively with salinity in two benthic foraminiferal species (Ammonia tepida and Amphistegina lessonii). The Na / Ca values differ between the two species, with an approximately 2-fold higher Na / Ca in A. lessonii than in A. tepida, coinciding with an offset in their Mg content ( ˜ 35 mmol mol-2 versus ˜ 2.5 mmol mol-1 for A. lessonii and A. tepida, respectively). Despite the offset in average Na / Ca values, the slopes of the Na / Ca-salinity regressions are similar between these two species (0.077 versus 0.064 mmol mol-1 change per salinity unit). In addition, Mg / Ca and Sr / Ca are positively correlated with salinity in cultured A. tepida but show no correlation with salinity for A. lessonii. Electron microprobe mapping of incorporated Na and Mg of the cultured specimens shows that within chamber walls of A. lessonii, Na / Ca and Mg / Ca occur in elevated bands in close proximity to the primary organic lining. Between species, Mg banding is relatively similar, even though Mg content is 10 times lower and that variation within the chamber wall is much less pronounced in A. tepida. In addition, Na banding is much less prominent in this species than it is in A. lessonii. Inter-species differences in element banding reported here are hypothesized to be caused by differences in biomineralization controls responsible for element uptake.

Copper enhances the activity and salt resistance of mixed methane-oxidizing communities.

PubMed

van der Ha, David; Hoefman, Sven; Boeckx, Pascal; Verstraete, Willy; Boon, Nico

2010-08-01

Effluents of anaerobic digesters are an underestimated source of greenhouse gases, as they are often saturated with methane. A post-treatment with methane-oxidizing bacterial consortia could mitigate diffuse emissions at such sites. Semi-continuously fed stirred reactors were used as model systems to characterize the influence of the key parameters on the activity of these mixed methanotrophic communities. The addition of 140 mg L(-1) NH (4) (+) -N had no significant influence on the activity nor did a temperature increase from 28 degrees C to 35 degrees C. On the other hand, addition of 0.64 mg L(-1) of copper(II) increased the methane removal rate by a factor of 1.5 to 1.7 since the activity of particulate methane monooxygenase was enhanced. The influence of different concentrations of NaCl was also tested, as effluents of anaerobic digesters often contain salt levels up to 10 g NaCl L(-1). At a concentration of 11 g NaCl L(-1), almost no methane-oxidizing activity was observed in the reactors without copper addition. Yet, reactors with copper addition exhibited a sustained activity in the presence of NaCl. A colorimetric test based on naphthalene oxidation showed that soluble methane monooxygenase was inhibited by copper, suggesting that the particulate methane monooxygenase was the active enzyme and thus more salt resistant. The results obtained demonstrate that the treatment of methane-saturated effluents, even those with increased ammonium (up to 140 mg L(-1) NH (4) (+) -N) and salt levels, can be mitigated by implementation of methane-oxidizing microbial consortia.

Green manure addition to soil increases grain zinc concentration in bread wheat.

PubMed

Aghili, Forough; Gamper, Hannes A; Eikenberg, Jost; Khoshgoftarmanesh, Amir H; Afyuni, Majid; Schulin, Rainer; Jansa, Jan; Frossard, Emmanuel

2014-01-01

Zinc (Zn) deficiency is a major problem for many people living on wheat-based diets. Here, we explored whether addition of green manure of red clover and sunflower to a calcareous soil or inoculating a non-indigenous arbuscular mycorrhizal fungal (AMF) strain may increase grain Zn concentration in bread wheat. For this purpose we performed a multifactorial pot experiment, in which the effects of two green manures (red clover, sunflower), ZnSO4 application, soil γ-irradiation (elimination of naturally occurring AMF), and AMF inoculation were tested. Both green manures were labeled with 65Zn radiotracer to record the Zn recoveries in the aboveground plant biomass. Application of ZnSO4 fertilizer increased grain Zn concentration from 20 to 39 mg Zn kg-1 and sole addition of green manure of sunflower to soil raised grain Zn concentration to 31 mg Zn kg-1. Adding the two together to soil increased grain Zn concentration even further to 54 mg Zn kg-1. Mixing green manure of sunflower to soil mobilized additional 48 µg Zn (kg soil)-1 for transfer to the aboveground plant biomass, compared to the total of 132 µg Zn (kg soil)-1 taken up from plain soil when neither green manure nor ZnSO4 were applied. Green manure amendments to soil also raised the DTPA-extractable Zn in soil. Inoculating a non-indigenous AMF did not increase plant Zn uptake. The study thus showed that organic matter amendments to soil can contribute to a better utilization of naturally stocked soil micronutrients, and thereby reduce any need for major external inputs.

Mg2BIV: Narrow Bandgap Thermoelectric Semiconductors

NASA Astrophysics Data System (ADS)

Kim, Il-Ho

2018-05-01

Thermoelectric materials can convert thermal energy directly into electric energy and vice versa. The electricity generation from waste heat via thermoelectric devices can be considered as a new energy source. For instance, automotive exhaust gas and all industrial processes generate an enormous amount of waste heat that can be converted to electricity by using thermoelectric devices. Magnesium compound Mg2BIV (BIV = Si, Ge or Sn) has a favorable combination of physical and chemical properties and can be a good base for the development of new efficient thermoelectrics. Because they possess similar properties to those of group BIV elemental semiconductors, they have been recognized as good candidates for thermoelectric applications. Mg2Si, Mg2Ge and Mg2Sn with an antifluorite structure are narrow bandgap semiconductors with indirect band gaps of 0.77 eV, 0.74 eV, and 0.35 eV, respectively. Mg2BIV has been recognized as a promising material for thermoelectric energy conversion at temperatures ranging from 500 K to 800 K. Compared to other thermoelectric materials operating in the similar temperature range, such as PbTe and filled skutterudites, the important aspects of Mg2BIV are non-toxic and earth-abundant elements. Based on classical thermoelectric theory, the material factor β ( m* / m e)3/2μκ L -1 can be utilized as the criterion for thermoelectric material selection, where m* is the density-of-states effective mass, me is the mass of an electron, μ is the carrier mobility, and κL is the lattice thermal conductivity. The β for magnesium silicides is 14, which is very high compared to 0.8 for iron silicides, 1.4 for manganese silicides, and 2.6 for silicon-germanium alloys. In this paper, basic phenomena of thermoelectricity and transport parameters for thermoelectric materials were briefly introduced, and thermoelectric properties of Mg2BIV synthesized by using a solid-state reaction were reviewed. In addition, various Mg2BIV compounds were discussed: intrinsic Mg2Si, doped Mg2Si:Dm (D = Al, In, Bi, Sb, Te or Se), and solid solutions of intrinsic/doped Mg2Si1 - x Sn x :D m and Mg2Si1 - x Ge x :D m .

Additive anticonvulsant effects of agmatine and lithium chloride on pentylenetetrazole-induced clonic seizure in mice: involvement of α₂-adrenoceptor.

PubMed

Bahremand, Arash; Ziai, Pouya; Payandemehr, Borna; Rahimian, Reza; Amouzegar, Afsaneh; Khezrian, Mina; Montaser-Kouhsari, Laleh; Meibodi, Maryam Aghaei; Ebrahimi, Ali; Ghasemi, Abbas; Ghasemi, Mehdi; Dehpour, Ahmad Reza

2011-09-01

After 60 years, lithium is still the mainstay in the treatment of mood disorders and widely used in clinic. In addition to its mood stabilizer effects, lithium also shows some anticonvulsant properties. Similar to lithium, agmatine also plays a protective role in the CNS against seizures and has been reported to enhance the effect of different antiepileptic agents. Moreover, both agmatine and lithium have modulatory effects on α(2)-adrenoceptors. So, we designed this study: 1) to investigate whether agmatine and lithium show an additive effect against clonic seizures induced by pentylenetetrazole; 2) to assess whether this additive effect is mediated through the α(2)-adrenoceptor or not. In our study, acute administration of a single effective dose of lithium chloride (30 mg/kg, i.p.) increased the seizure threshold. Pre-treatment with low and, per se, non-effective doses of agmatine (1 and 3mg/kg) potentiated a sub-effective dose of lithium (10mg/kg). Interestingly, the anticonvulsant effects of these effective combinations of lithium and agmatine were prevented by pre-treatment with low and non-effective doses of yohimbine [α(2)-adrenoceptor antagonist] (0.1 and 0.5mg/kg). On the other hand, clonidine [α(2)-adrenoceptor agonist] augmented the anticonvulsant effect of a sub-effective combination of lithium (5mg/kg i.p.) and agmatine (1mg/kg) at relatively low doses (0.1 and 0.25mg/kg). In summary, our findings demonstrate that agmatine and lithium chloride exhibit additive anticonvulsant properties which seem to be mediated through α(2)-adrenoceptor. Copyright © 2011. Published by Elsevier B.V.

Treatment of Myasthenia Gravis Based on Its Immunopathogenesis

PubMed Central

Kim, Jee Young; Park, Kee Duk

2011-01-01

The prognosis of myasthenia gravis (MG) has improved dramatically due to advances in critical-care medicine and symptomatic treatments. Its immunopathogenesis is fundamentally a T-cell-dependent autoimmune process resulting from loss of tolerance toward self-antigens in the thymus. Thymectomy is based on this immunological background. For MG patients who are inadequately controlled with sufficient symptomatic treatment or fail to achieve remission after thymectomy, remission is usually achieved through the addition of other immunotherapies. These immunotherapies can be classified into two groups: rapid induction and long-term maintenance. Rapid induction therapy includes intravenous immunoglobulin (IVIg) and plasma exchange (PE). These produce improvement within a few days after initiation, and so are useful for acute exacerbation including myasthenic crisis or in the perioperative period. High-dose prednisone has been more universally preferred for remission induction, but it acts more slowly than IVIg and PE, commonly only after a delay of several weeks. Slow tapering of steroids after a high-dose pulse offers a method of maintaining the state of remission. However, because of significant side effects, other immunosuppressants (ISs) are frequently added as "steroid-sparing agents". The currently available ISs exert their immunosuppressive effects by three mechanisms: 1) blocking the synthesis of DNA and RNA, 2) inhibiting T-cell activation and 3) depleting the B-cell population. In addition, newer drugs including antisense molecule, tumor necrosis factor alpha receptor blocker and complement inhibitors are currently under investigation to confirm their effectiveness. Until now, the treatment of MG has been based primarily on experience rather than gold-standard evidence from randomized controlled trials. It is hoped that well-organized studies and newer experimental trials will lead to improved treatments. PMID:22259613

Peginterferon alfa-2b and weight-based or flat-dose ribavirin in chronic hepatitis C patients: a randomized trial.

PubMed

Jacobson, Ira M; Brown, Robert S; Freilich, Bradley; Afdhal, Nezam; Kwo, Paul Y; Santoro, John; Becker, Scott; Wakil, Adil E; Pound, David; Godofsky, Eliot; Strauss, Robert; Bernstein, David; Flamm, Steven; Pauly, Mary Pat; Mukhopadhyay, Pabak; Griffel, Louis H; Brass, Clifford A

2007-10-01

This prospective, multicenter, community-based and academic-based, open-label, investigator-initiated, U.S. study evaluated efficacy and safety of pegylated interferon (PEG-IFN) alfa-2b plus a flat or weight-based dose of ribavirin (RBV) in adults with chronic hepatitis C. Patients (n = 5027) were randomly assigned to receive PEG-IFN alfa-2b 1.5 microg/kg/week plus flat-dose (800 mg/day) or weight-based (800-1400 mg/day) RBV for 48 weeks (patients with genotype 1, 4, 5, or 6) and for 24 or 48 weeks (genotype 2/3 patients). Primary end point was sustained virologic response (undetectable [<125 IU/mL] serum hepatitis C virus RNA at 24-week follow-up). Sustained virologic response, but not end-of-treatment, rates were significantly higher with weight-based than with flat-dose RBV (44.2% versus 40.5%; P = 0.008). Sustained virologic response rates by intention-to-treat analysis were 34.0% and 28.9%, respectively, in genotype 1 patients (P = 0.005) and 31.2% and 26.7%, respectively, in genotype 1 patients with high baseline viral load (P = 0.056). In genotype 2/3 patients, rates were not significantly different (61.8% and 59.5%, respectively) regardless of treatment duration. Besides greater hemoglobin reductions with weight-based RBV, safety profiles were similar across RBV dosing groups, including the 1400-mg/day group. PEG-IFN alfa-2b plus weight-based RBV is more effective than flat-dose RBV, particularly in genotype 1 patients, providing equivalent efficacy across all weight groups. RBV 1400 mg/day is appropriate for patients 105 to 125 kg. For genotype 2/3 patients, 24 weeks of treatment with flat-dose RBV is adequate; no evidence of additional benefit of extending treatment to 48 weeks was demonstrated.

Improving sediment-quality guidelines for nickel: development and application of predictive bioavailability models to assess chronic toxicity of nickel in freshwater sediments

USGS Publications Warehouse

Vangheluwe, Marnix L. U.; Verdonck, Frederik A. M.; Besser, John M.; Brumbaugh, William G.; Ingersoll, Christopher G.; Schlekat, Christan E.; Rogevich Garman, Emily

2013-01-01

Within the framework of European Union chemical legislations an extensive data set on the chronic toxicity of sediment nickel has been generated. In the initial phase of testing, tests were conducted with 8 taxa of benthic invertebrates in 2 nickel-spiked sediments, including 1 reasonable worst-case sediment with low concentrations of acid-volatile sulfide (AVS) and total organic carbon. The following species were tested: amphipods (Hyalella azteca, Gammarus pseudolimnaeus), mayflies (Hexagenia sp.), oligochaetes (Tubifex tubifex, Lumbriculus variegatus), mussels (Lampsilis siliquoidea), and midges (Chironomus dilutus, Chironomus riparius). In the second phase, tests were conducted with the most sensitive species in 6 additional spiked sediments, thus generating chronic toxicity data for a total of 8 nickel-spiked sediments. A species sensitivity distribution was elaborated based on 10% effective concentrations yielding a threshold value of 94 mg Ni/kg dry weight under reasonable worst-case conditions. Data from all sediments were used to model predictive bioavailability relationships between chronic toxicity thresholds (20% effective concentrations) and AVS and Fe, and these models were used to derive site-specific sediment-quality criteria. Normalization of toxicity values reduced the intersediment variability in toxicity values significantly for the amphipod species Hyalella azteca and G. pseudolimnaeus, but these relationships were less clearly defined for the mayfly Hexagenia sp. Application of the models to prevailing local conditions resulted in threshold values ranging from 126 mg to 281 mg Ni/kg dry weight, based on the AVS model, and 143 mg to 265 mg Ni/kg dry weight, based on the Fe model

New concept for a toxicity assay based on multiple indexes from the wave shape of damped metabolic oscillation induced in living yeast cells (part II): application to analytical toxicology.

PubMed

Nakamura, H; Suzuki, M

2007-10-01

An ideal toxicity assay should utilize multiple indexes obtained from transient changes of metabolic activities. Here, we demonstrate the possibility for a novel toxicity bioassay using the damped glycolytic oscillation phenomenon occurring in starved yeast cells. In a previous study, the phenomenon was characterized in detail. Under optimum conditions to induce the phenomenon, the wave shapes of the damped glycolytic oscillations were changed by the instantaneous addition of both glucose and chemicals and by changing the chemical concentration. We estimated the changes in the oscillation wave shapes as six indexes, i.e., the number of wave cycles, maximum amplitude, oscillation frequency, attenuation coefficient, initial peak height, and non-steady-state time. These index changes were obtained from several kinds of chemicals. The chemicals, especially those for acids (0.01-100 mM HCl and 0.01-50 mM citric acid), bases (0.001-50 mM KOH), heavy metal ions (1-1,000 mg L(-1); Cu(2+), Pb(2+), Cd(2+), Hg(2+)), respiratory inhibitors (3-500 mg L(-1) NaN(3)), dissolved oxygen removers (10-300 mg L(-1) NaSO(3)), surfactants (10-200 mg L(-1) benzalkonium chloride), and aldehyde (10-1,000 mg L(-1) acetaldehyde), showed characteristic patterns depending on each chemical and its concentration. These significant results demonstrate the possibilities of new methods for both toxicity qualification and quantification.

CdCl2 passivation of polycrystalline CdMgTe and CdZnTe absorbers for tandem photovoltaic cells

NASA Astrophysics Data System (ADS)

Swanson, Drew E.; Reich, Carey; Abbas, Ali; Shimpi, Tushar; Liu, Hanxiao; Ponce, Fernando A.; Walls, John M.; Zhang, Yong-Hang; Metzger, Wyatt K.; Sampath, W. S.; Holman, Zachary C.

2018-05-01

As single-junction silicon solar cells approach their theoretical limits, tandems provide the primary path to higher efficiencies. CdTe alloys can be tuned with magnesium (CdMgTe) or zinc (CdZnTe) for ideal tandem pairing with silicon. A II-VI/Si tandem holds the greatest promise for inexpensive, high-efficiency top cells that can be quickly deployed in the market using existing polycrystalline CdTe manufacturing lines combined with mature silicon production lines. Currently, all high efficiency polycrystalline CdTe cells require a chloride-based passivation process to passivate grain boundaries and bulk defects. This research examines the rich chemistry and physics that has historically limited performance when extending Cl treatments to polycrystalline 1.7-eV CdMgTe and CdZnTe absorbers. A combination of transmittance, quantum efficiency, photoluminescence, transmission electron microscopy, and energy-dispersive X-ray spectroscopy clearly reveals that during passivation, Mg segregates and out-diffuses, initially at the grain boundaries but eventually throughout the bulk. CdZnTe exhibits similar Zn segregation behavior; however, the onset and progression is localized to the back of the device. After passivation, CdMgTe and CdZnTe can render a layer that is reduced to predominantly CdTe electro-optical behavior. Contact instabilities caused by inter-diffusion between the layers create additional complications. The results outline critical issues and paths for these materials to be successfully implemented in Si-based tandems and other applications.

Actigraphy-based sleep parameters during the reinstatement of methamphetamine self-administration in rhesus monkeys.

PubMed

Berro, Laís F; Andersen, Monica L; Tufik, Sergio; Howell, Leonard L

2016-04-01

The objective of this study was to investigate nighttime activity of nonhuman primates during extinction and cue- and drug-primed reinstatement of methamphetamine self-administration. Adult rhesus monkeys (Macaca mulatta; n = 5) self-administered methamphetamine (0.01 mg/kg/injection, i.v.) under a fixed-ratio 20 schedule of reinforcement. Saline infusions were then substituted for methamphetamine and stimulus light (drug-conditioned stimulus presented during drug self-administration) withheld until subjects reached extinction criteria. Drug- and cue-induced reinstatement effects were evaluated after i.v. noncontingent priming injections of methamphetamine (0.03, 0.1, or 0.3 mg/kg). Activity-based sleep measures were evaluated with Actiwatch monitors a week before (baseline nighttime activity parameters) and throughout the protocol. Although methamphetamine self-administration did not significantly affect nighttime activity compared to baseline, sleeplike parameters were improved during extinction compared to self-administration maintenance. Priming injection of 0.1 mg/kg methamphetamine, but not 0.03 or 0.3 mg/kg, induced significant reinstatement effects. These behavioral responses were accompanied by nighttime outcomes, with increased sleep fragmentation and decreased sleep efficiency in the night following 0.1 mg/kg methamphetamine-induced reinstatement. In the absence of both drug and drug-paired cues (extinction conditions), nighttime activity decreased compared to self-administration maintenance. Additionally, effective reinstatement conditions impaired sleeplike measures. Our data indicate that the reintroduction of the stimulus light as a drug-paired cue increased nighttime activity. (c) 2016 APA, all rights reserved).

Analytical interference by monoclonal immunoglobulins on the direct bilirubin AU Beckman Coulter assay: the benefit of unsuspected diagnosis from spurious results.

PubMed

García-González, Elena; González-Tarancón, Ricardo; Aramendía, Maite; Rello, Luis

2016-08-01

Monoclonal (M) components can interfere with the direct bilirubin (D-Bil) assay on the AU Beckman Coulter instrumentation and produce spurious results, such as D-Bil values greater than total bilirubin (T-Bil) or very low/negative D-Bil values. If properly detected, this interference may uncover undiagnosed patients with monoclonal gammopathy (MG). We investigated the interference rate on the D-Bil AU assay in serum samples known to contain M proteins along with their isotype and described the protocol set up in our laboratory to help with the diagnosis of MG based on D-Bil spurious results as first indication. During a period of 4 years, 15.4% (345 of 2235) of serum samples containing M immunoglobulins produced erroneous D-Bil results, although no clear relationship between the magnitude or isotype of the M component and interference could be found. In total 22 new patients were diagnosed with MG based on the analytical artefact with the D-Bil as first indication. The D-Bil interference from MG on the Beckman AU analysers needs to be made known to laboratories in order to prevent clinical confusion and/or additional workup to explain the origin of anomalous results. Although this information may not add to the management of existing patients with serum paraproteins, it can benefit patients that have not been diagnosed with MG by triggering follow up testing to determine if M components are present.

The combined effects of vinclozolin and procymidone do not deviate from expected additivity in vitro and in vivo.

PubMed

Nellemann, Christine; Dalgaard, Majken; Lam, Henrik Rye; Vinggaard, Anne Marie

2003-02-01

The combination effects of the well-known antiandrogenic fungicides, vinclozolin and procymidone, were tested both in vitro and in vivo. In vitro both vinclozolin and procymidone significantly inhibited the binding of agonist to the androgen receptor with the concentration that resulted in 50% inhibition (IC(50)) values of 0.1 and 0.6 micro M, respectively. By applying the isobole method, the effect of combining the two pesticides in vitro was found to be additive. In castrated testosterone-treated rats the administration of vinclozolin starting at 10 mg/kg led to a decrease in organ weight of all tested reproductive organs. The levels of luteinizing hormone (LH) and follicle stimulating hormone (FSH) were increased significantly with doses of 100 mg/kg vinclozolin and above. Expression of the androgen-responsive gene, TRPM-2, was increased starting at 100 mg/kg vinclozolin. For procymidone, reproductive organ weights were diminished at 10 mg/kg and LH was increased at a concentration of 25 mg/kg and above, compared to the testosterone-treated controls. FSH was significantly increased only at 25 mg/kg procymidone. The studied gene expressions were changed by 100 mg/kg procymidone. Dosing the animals with a combination of a 1:1 mixture of vinclozolin and procymidone resulted in a weight reduction in the reproductive organs and an increase of serum LH and FSH as early as with 10 mg/kg combined dose. The relative expressions of TRPM-2 and PBP C3 were changed compared to controls at 100 mg/kg. The level of 5-HT in the rat brain was increased after a dose of 10 mg/kg. Using the isobole method, comparisons of the observed and predicted effects assuming additivity on reproductive organ weights, hormone levels, and gene expression showed agreement and thus the combination effects are suggested to be additive in vivo as well as in vitro.

[Protein -based diet with respect to the principles of rational nutrition. Menus analysis].

PubMed

Szczuko, Małgorzata; Pieszak, Natalia; Jamioł -Milc, Dominika; Stachowska, Ewa

A diet high in protein and low in carbohydrates has four phases, first of them being the attack phase, which eliminates carbohydrates to the highest extent. In subsequent phases the consumption of carbohydrates is gradually allowed but their ratio is limited. The aim of performed studies was to analyze the metabolic effects of protein -based diet. The hypothesis – the analysis based on the composition of the diets should draw the attention to health risks being not only related to too high consumption of protein. In the study, 40 diets were composed according to the objectives of high protein diet – 10 diets for each of the four phases. Next, the diets were introduced into dietetic program Dietician 2 recommended by the National Food and Nutrition Institute in Poland, and the amounts of nutrients supplied with the diets were calculated. Those amounts were compared to the currently recommended dietary allowances in Poland. Based on too high consumption of some nutrients and the deficiency of others in the diets, the highest detrimental effect was determined for the first two phases of the diet. In all four phases of the diet, too high consumption of protein, UFA and cholesterol was determined, which amounted to 148.8–160.5 g/day, 12.5–16.2 g/day and 467.7–488.7 mg/day, respectively. Simultaneously, too low average consumption was noted in case of energy (1131–1690 kcal), carbohydrates (58.2–149.4 g) and dietary fiber (3.3–28.7 g) in all phases of the diet. Additionally, the deficiency in vitamin E (2.69–7.21 mg) was observed in the first three phases of the diet, and thiamin in the first two phases (0.72–1.02 mg). The most deficient phase of the diet was the first phase – the attack phase, where the deficiency also concerned folacin (154.4 mg/day), vitamin C (6.14 mg), potassium (2947.7 mg), iron (7.19 mg), copper (0.59 mg) and magnesium (294.8 mg). The main causes of body mass reduction in high protein diet are caloric restrictions in all diet phases. The analyses of diets compositions determined the potential negative effect of using this diet in case of people with predisposition to kidney diseases, gout, cardiovascular diseases, anemia and erythropoiesis disorders. The most detrimental was the first phase of the diet, which entirely eliminates carbohydrate products.

Development of biodegradable Zn-1X binary alloys with nutrient alloying elements Mg, Ca and Sr.

PubMed

Li, H F; Xie, X H; Zheng, Y F; Cong, Y; Zhou, F Y; Qiu, K J; Wang, X; Chen, S H; Huang, L; Tian, L; Qin, L

2015-05-29

Biodegradable metals have attracted considerable attentions in recent years. Besides the early launched biodegradable Mg and Fe metals, Zn, an essential element with osteogenic potential of human body, is regarded and studied as a new kind of potential biodegradable metal quite recently. Unfortunately, pure Zn is soft, brittle and has low mechanical strength in the practice, which needs further improvement in order to meet the clinical requirements. On the other hand, the widely used industrial Zn-based alloys usually contain biotoxic elements (for instance, ZA series contain toxic Al elements up to 40 wt.%), which subsequently bring up biosafety concerns. In the present work, novel Zn-1X binary alloys, with the addition of nutrition elements Mg, Ca and Sr were designed (cast, rolled and extruded Zn-1Mg, Zn-1Ca and Zn-1Sr). Their microstructure and mechanical property, degradation and in vitro and in vivo biocompatibility were studied systematically. The results demonstrated that the Zn-1X (Mg, Ca and Sr) alloys have profoundly modified the mechanical properties and biocompatibility of pure Zn. Zn-1X (Mg, Ca and Sr) alloys showed great potential for use in a new generation of biodegradable implants, opening up a new avenue in the area of biodegradable metals.

Development of biodegradable Zn-1X binary alloys with nutrient alloying elements Mg, Ca and Sr

PubMed Central

Li, H. F.; Xie, X. H.; Zheng, Y. F.; Cong, Y.; Zhou, F. Y.; Qiu, K. J.; Wang, X.; Chen, S. H.; Huang, L.; Tian, L.; Qin, L.

2015-01-01

Biodegradable metals have attracted considerable attentions in recent years. Besides the early launched biodegradable Mg and Fe metals, Zn, an essential element with osteogenic potential of human body, is regarded and studied as a new kind of potential biodegradable metal quite recently. Unfortunately, pure Zn is soft, brittle and has low mechanical strength in the practice, which needs further improvement in order to meet the clinical requirements. On the other hand, the widely used industrial Zn-based alloys usually contain biotoxic elements (for instance, ZA series contain toxic Al elements up to 40 wt.%), which subsequently bring up biosafety concerns. In the present work, novel Zn-1X binary alloys, with the addition of nutrition elements Mg, Ca and Sr were designed (cast, rolled and extruded Zn-1Mg, Zn-1Ca and Zn-1Sr). Their microstructure and mechanical property, degradation and in vitro and in vivo biocompatibility were studied systematically. The results demonstrated that the Zn-1X (Mg, Ca and Sr) alloys have profoundly modified the mechanical properties and biocompatibility of pure Zn. Zn-1X (Mg, Ca and Sr) alloys showed great potential for use in a new generation of biodegradable implants, opening up a new avenue in the area of biodegradable metals. PMID:26023878

Review of Methods for the Detection and Determination of Malachite Green and Leuco-Malachite Green in Aquaculture.

PubMed

Zhou, Xinhui; Zhang, Jiaran; Pan, Zhongli; Li, Daoliang

2018-05-14

Malachite green (MG) has been widely used in the aquaculture industry as a fungicide and parasiticide because of its high efficiency and low cost, and it is commonly found in aquatic products and environmental water. However, MG and its primary metabolite, leuco-malachite green (LMG), are also toxic inorganic contaminants that are hazardous to the health of humans and other organisms. A variety of methods have been proposed in recent years for detecting and monitoring MG and LMG. This article was compiled as a general review of the methods proposed for MG and LMG detection, and several important detection parameters, such as the limit of detection, recovery and relative standard deviation, were tabulated. The analytical methods for the determination of MG and LMG in various matrices include high-performance liquid chromatography separation-based methods, liquid chromatography tandem mass spectrometry, surface-enhanced Raman spectroscopy, electrochemical methods, immunological assays, spectrophotometry and fluorescent methods which were described in detail in this article. In addition, some sample preparation techniques were also described. This review can provide expert guidance to the reader on the advantages, disadvantages and applicability of the different methodologies. This review also discussed challenges and several perspectives on the future trends in the determination of MG and LMG.

Determination of malachite green in fish based on magnetic molecularly imprinted polymer extraction followed by electrochemiluminescence.

PubMed

Huang, Baomei; Zhou, Xibin; Chen, Jing; Wu, Guofan; Lu, Xiaoquan

2015-09-01

A novel procedure for selective extraction of malachite green (MG) from fish samples was set up by using magnetic molecularly imprinted polymers (MMIP) as the solid phase extraction material followed by electrochemiluminescence (ECL) determination. MMIP was prepared by using Fe3O4 magnetite as magnetic component, MG as template molecule, methacrylic acid (MAA) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as crosslinking agent. MMIP was characterized by SEM, TEM, FT-IR, VSM and XRD. Leucomalachite green (LMG) was oxidized in situ to MG by 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ). And then MMIP was successfully used to selectively enrich MG from fish samples. Adsorbed MG was desorbed and determined by ECL. Under the optimal conditions, calibration curve was good linear in the range of 0.29-290 μg/kg and the limit of detection (LOD) was 7.3 ng/kg (S/N=3). The recoveries of MMIP extraction were 77.1-101.2%. In addition, MMIP could be regenerated. To the best of our knowledge, MMIP coupling with ECL quenching of Ru(bpy)3(2+)/TPA for the determination of MG has not yet been developed. Copyright © 2015 Elsevier B.V. All rights reserved.

Thermoelectric Materials

NASA Astrophysics Data System (ADS)

Gao, Peng; Berkun, Isil; Schmidt, Robert D.; Luzenski, Matthew F.; Lu, Xu; Bordon Sarac, Patricia; Case, Eldon D.; Hogan, Timothy P.

2014-06-01

Mg2(Si,Sn) compounds are promising candidate low-cost, lightweight, nontoxic thermoelectric materials made from abundant elements and are suited for power generation applications in the intermediate temperature range of 600 K to 800 K. Knowledge on the transport and mechanical properties of Mg2(Si,Sn) compounds is essential to the design of Mg2(Si,Sn)-based thermoelectric devices. In this work, such materials were synthesized using the molten-salt sealing method and were powder processed, followed by pulsed electric sintering densification. A set of Mg2.08Si0.4- x Sn0.6Sb x (0 ≤ x ≤ 0.072) compounds were investigated, and a peak ZT of 1.50 was obtained at 716 K in Mg2.08Si0.364Sn0.6Sb0.036. The high ZT is attributed to a high electrical conductivity in these samples, possibly caused by a magnesium deficiency in the final product. The mechanical response of the material to stresses is a function of the elastic moduli. The temperature-dependent Young's modulus, shear modulus, bulk modulus, Poisson's ratio, acoustic wave speeds, and acoustic Debye temperature of the undoped Mg2(Si,Sn) compounds were measured using resonant ultrasound spectroscopy from 295 K to 603 K. In addition, the hardness and fracture toughness were measured at room temperature.

Bone substitute material composition and morphology differentially modulate calcium and phosphate release through osteoclast-like cells.

PubMed

Konermann, A; Staubwasser, M; Dirk, C; Keilig, L; Bourauel, C; Götz, W; Jäger, A; Reichert, C

2014-04-01

The aim of this study was to determine the material composition and cell-mediated remodelling of different calcium phosphate-based bone substitutes. Osteoclasts were cultivated on bone substitutes (Cerabone, Maxresorb, and NanoBone) for up to 5 days. Bafilomycin A1 addition served as the control. To determine cellular activity, the supernatant content of calcium and phosphate was measured by inductively coupled plasma optical emission spectrometry. Cells were visualized on the materials by scanning electron microscopy. Material composition and surface characteristics were assessed by energy-dispersive X-ray spectroscopy. Osteoclast-induced calcium and phosphate release was material-specific. Maxresorb exhibited the highest ion release to the medium (P = 0.034; calcium 40.25mg/l day 5, phosphate 102.08 mg/l day 5) and NanoBone the lowest (P = 0.021; calcium 8.43 mg/l day 5, phosphate 15.15 mg/l day 5); Cerabone was intermediate (P = 0.034; calcium 16.34 mg/l day 5, phosphate 30.6 mg/l day 5). All investigated materials showed unique resorption behaviours. The presented methodology provides a new perspective on the investigation of bone substitute biodegradation, maintaining the material-specific micro- and macrostructure. Copyright © 2013 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Naked eye and spectrophotometric detection of chromogenic insecticide in aquaculture using amine functionalized gold nanoparticles in the presence of major interferents

NASA Astrophysics Data System (ADS)

Loganathan, C.; John, S. Abraham

2017-02-01

Detection of a chromogenic insecticide, malachite green (MG) using 3,5-diamino-1,2,4-triazole capped gold nanoparticles (DAT-AuNPs) by both naked eye and spectrophotometry was described in this paper. The DAT-AuNPs were prepared by wet chemical method and show absorption maximum at 518 nm. The zeta potential of DAT-AuNPs was found to be - 39.9 mV, suggesting that one of the amine groups of DAT adsorbed on the surface of AuNPs and the other amine group stabilizes the AuNPs from aggregation. The wine red color DAT-AuNPs changes to violet while adding 25 μM MG whereas the absorption band at 518 nm was increased and shifted towards longer wavelength. However, addition of 70 μM MG leads to the aggregation of DAT-AuNPs. This is due to strong electrostatic interaction between ammonium ion of MG and the free amine group of DAT. Based on the color change and shift in SPR band, 25 and 5 μM MG can be easily detected by naked eye and spectrophotometry. The DAT-AuNPs show high selectivity towards MG even in the presence of 5000-fold higher concentrations of common interferents. The practical application was successfully demonstrated by determining MG in fish farm water.

Tribological Behavior of Aluminum Alloy AlSi10Mg-TiB2 Composites Produced by Direct Metal Laser Sintering (DMLS)

NASA Astrophysics Data System (ADS)

Lorusso, Massimo; Aversa, Alberta; Manfredi, Diego; Calignano, Flaviana; Ambrosio, Elisa Paola; Ugues, Daniele; Pavese, Matteo

2016-08-01

Direct metal laser sintering (DMLS) is an additive manufacturing technique for the production of parts with complex geometry and it is especially appropriate for structural applications in aircraft and automotive industries. Aluminum-based metal matrix composites (MMCs) are promising materials for these applications because they are lightweight, ductile, and have a good strength-to-weight ratio This paper presents an investigation of microstructure, hardness, and tribological properties of AlSi10Mg alloy and AlSi10Mg alloy/TiB2 composites prepared by DMLS. MMCs were realized with two different compositions: 10% wt. of microsize TiB2, 1% wt. of nanosize TiB2. Wear tests were performed using a pin-on-disk apparatus on the prepared samples. Performances of AlSi10Mg samples manufactured by DMLS were also compared with the results obtained on AlSi10Mg alloy samples made by casting. It was found that the composites displayed a lower coefficient of friction (COF), but in the case of microsize TiB2 reinforcement the wear rate was higher than with nanosize reinforcements and aluminum alloy without reinforcement. AlSi10Mg obtained by DMLS showed a higher COF than AlSi10Mg obtained by casting, but the wear rate was higher in the latter case.

Electronic structure of scandium-doped MgB2

NASA Astrophysics Data System (ADS)

de La Peña, Omar; Agrestini, Stefano

2005-03-01

Recently has been reported the synthesis of a new superconducting alloy based on MgB2, where Mg is partially substituted with Sc. In order to analyze the effect of Sc doping on the structural and superconducting properties of Mg1-xScxB2, we have performed a detailed study of the electronic structure for this new diboride. The calculations have been done using the first-principles LAPW method, within the supercell approach for modeling the doping. In this work we report results for the electronic band structure, Fermi surface, and density of states. The effect of the Sc-d orbitals on the structural and electronic properties of Mg1-xScxB2 is analyzed. Increasing the Sc concentration (x) the σ-band is gradually filled, because Sc have one valence electron more than Mg. Interestingly, the analysis of the band structure shows that even for ScB2 the top of the σ-band remain above the Fermi level, nevertheless the σ-band presents high dispersion and has an important contribution of d states. In this way, in addition to the band filling effect, Sc doping gradually reduces the two-dimensional character of the σ- band in Mg1-xScxB2 as a result of increasing the sp(B)-d(Sc) hybridization. This research was partially supported by Consejo Nacional de Ciencia y Tecnolog'ia (CONACYT, M'exico) under Grant. No. 43830-F

Preparation of MgO-SnO2-TiO2 Materials and Their Corrosion in Na3AlF6-AlF3-K3AlF6 Bath

NASA Astrophysics Data System (ADS)

Xu, Yibiao; Li, Yawei; Sang, Shaobai; Ren, Bo; Qin, Qingwei; Yang, Jianhong

2015-01-01

New types of refractory materials need to be developed for designing the so-called ledge-free sidewalls of the Hall-Héroult cell for aluminum extraction, which are currently constructed using Si3N4 bonded SiC refractories. In the present paper, MgO-based materials as potential candidate sidewalls were prepared using fused magnesia, tin dioxide, and anatase powder as starting materials. The reaction sintering process of the MgO-SnO2-TiO2 materials was investigated by means of X-ray diffraction and scanning electron microscope (SEM). All the specimens were corroded in a Na3AlF6-AlF3-K3AlF6 bath to assess the electrolyte corrosion resistance. The results show that reaction sintering occurs in the MgO-SnO2-TiO2 system in the range of 1373 K to 1873 K (1100 °C to 1600 °C). Firstly, MgO reacts separately with TiO2 and SnO2 to produce the Mg2TiO4 and Mg2SnO4 phases at 1373 K (1100 °C), which in turn react to form the Mg2Ti x Sn1-x O4 composite spinel at temperatures above 1373 K (1100 °C). All the specimens prepared are composed of the composite spinel and periclase phases. Increasing the SnO2 addition from 2 to 10 wt pct enhances densification of the specimens, which is accompanied by the formation of homogeneously distributed composite spinels in the MgO matrix, but the density of the specimen decreases when the amount of SnO2 added is higher than 10 wt pct due to larger volume expansion and agglomeration of the composite spinel. The MgO-SnO2-TiO2 refractories prepared exhibit good corrosion resistance to the electrolyte melts owing to their high density and formation of the composite spinel in the specimens. Their corrosion resistance increases progressively with the increase in the SnO2 addition owing to the formation of more chemically stable composite spinel.

Removal of Chromium from Soils Cultivated with Maize (Zea Mays) After the Addition of Natural Minerals as Soil Amendments.

PubMed

Μolla, A; Ioannou, Z; Mollas, S; Skoufogianni, E; Dimirkou, A

2017-03-01

The efficiency of natural minerals, i.e. zeolite, bentonite and goethite, regarding the retention of chromium, from maize was examined. Specifically, 1.0 kg of soil, 1.0 g of soil amendment and either 50 mg L -1 Cr(III) or 1 mg L -1 Cr(VI) were added in plant pots. Then, seeds of maize were cultivated. Each treatment was repeated three times. The statistical results of the experiments were analyzed by LSD test. Cr(III) addition in soil has shown that zeolite was the only amendment that increased the dry weight. Zeolite and bentonite reduced significantly the total chromium in plants after the addition of 50 mg L -1 Cr(III). The addition of Cr(VI) in soil has shown that bentonite was the only amendment that increased the dry weight of biomass and the plants' height. All soil amendments reduced to zero the total chromium concentration measured to plants after the addition of 1 mg L -1 Cr(VI).

A RESTful API for accessing microbial community data for MG-RAST.

PubMed

Wilke, Andreas; Bischof, Jared; Harrison, Travis; Brettin, Tom; D'Souza, Mark; Gerlach, Wolfgang; Matthews, Hunter; Paczian, Tobias; Wilkening, Jared; Glass, Elizabeth M; Desai, Narayan; Meyer, Folker

2015-01-01

Metagenomic sequencing has produced significant amounts of data in recent years. For example, as of summer 2013, MG-RAST has been used to annotate over 110,000 data sets totaling over 43 Terabases. With metagenomic sequencing finding even wider adoption in the scientific community, the existing web-based analysis tools and infrastructure in MG-RAST provide limited capability for data retrieval and analysis, such as comparative analysis between multiple data sets. Moreover, although the system provides many analysis tools, it is not comprehensive. By opening MG-RAST up via a web services API (application programmers interface) we have greatly expanded access to MG-RAST data, as well as provided a mechanism for the use of third-party analysis tools with MG-RAST data. This RESTful API makes all data and data objects created by the MG-RAST pipeline accessible as JSON objects. As part of the DOE Systems Biology Knowledgebase project (KBase, http://kbase.us) we have implemented a web services API for MG-RAST. This API complements the existing MG-RAST web interface and constitutes the basis of KBase's microbial community capabilities. In addition, the API exposes a comprehensive collection of data to programmers. This API, which uses a RESTful (Representational State Transfer) implementation, is compatible with most programming environments and should be easy to use for end users and third parties. It provides comprehensive access to sequence data, quality control results, annotations, and many other data types. Where feasible, we have used standards to expose data and metadata. Code examples are provided in a number of languages both to show the versatility of the API and to provide a starting point for users. We present an API that exposes the data in MG-RAST for consumption by our users, greatly enhancing the utility of the MG-RAST service.

Synthesis of Pt/K2CO3/MgAlOx–reduced graphene oxide hybrids as promising NOx storage–reduction catalysts with superior catalytic performance

PubMed Central

Mei, Xueyi; Yan, Qinghua; Lu, Peng; Wang, Junya; Cui, Yuhan; Nie, Yu; Umar, Ahmad; Wang, Qiang

2017-01-01

Pt/K2CO3/MgAlOx–reduced graphene oxide (Pt/K/MgAlOx–rGO) hybrids were synthesized, characterized and tested as a promising NOx storage and reduction (NSR) catalyst. Mg–Al layered double hydroxides (LDHs) were grown on rGO via in situ hydrothermal crystallization. The structure and morphology of samples were thoroughly characterized using various techniques. Isothermal NOx adsorption tests indicated that MgAlOx–rGO hybrid exhibited better NOx trapping performance than MgAlOx, from 0.44 to 0.61 mmol · g−1, which can be attributed to the enhanced particle dispersion and stabilization. In addition, a series of MgAlOx–rGO loaded with 2 wt% Pt and different loadings (5, 10, 15, and 20 wt%) of K2CO3 (denoted as Pt/K/MgAlOx–rGO) were obtained by sequential impregnation. The influence of 5% H2O on the NOx storage capacity of MgAlOx–rGO loaded with 2 wt% Pt and 10% K2CO3 (2Pt/10 K/MgAlOx–rGO) catalyst was also evaluated. In all, the 2Pt/10 K/MgAlOx–rGO catalyst not only exhibited high thermal stability and NOx storage capacity of 1.12 mmol · g−1, but also possessed excellent H2O resistance and lean–rich cycling performance, with an overall 78.4% of NOx removal. This work provided a new scheme for the preparation of highly dispersed MgAlOx–rGO hybrid based NSR catalysts. PMID:28205630

Interface formation of epitaxial MgO/Co2MnSi(001) structures: Elemental segregation and oxygen migration

NASA Astrophysics Data System (ADS)

McFadden, Anthony; Wilson, Nathaniel; Brown-Heft, Tobias; Pennachio, Daniel; Pendharkar, Mihir; Logan, John A.; Palmstrøm, Chris J.

2017-12-01

The interface formation in epitaxial MgO /Co2MnSi (001) films was studied using in-situ X-ray photoelectron spectroscopy (XPS). MgO was deposited on single crystal Co2MnSi (001) layers using e-beam evaporation: a technique which is expected to oxidize the Co2MnSi layer somewhat due to the rise in oxygen partial pressure during MgO deposition while leaving the deposited MgO oxygen deficient. Not unexpectedly, we find that e-beam evaporation of MgO raises the oxygen background in the deposition chamber to a level that readily oxidizes the Co2MnSi surface, with oxygen bonding preferentially to Mn and Si over Co. Interestingly, this oxidation causes an elemental segregation, with Mn-Si effectively moving toward the surface, resulting in an MgO /Co2MnSi interface with a composition significantly differing from the original surface of the unoxidized Co2MnSi film. As MgO is deposited on the oxidized Co2MnSi , the Mn-oxides are reduced, while the Si oxide remains, and is only somewhat reduced after additional annealing in ultrahigh vacuum. Annealing after the MgO is grown on Co2MnSi causes oxygen to move away from the oxidized Co2MnSi interface toward the surface and into the MgO. This observation is consistent with an increase in the tunneling magnetoresistance ratio with post-growth annealing measured in fabricated magnetic tunnel junctions (MTJs). The findings are discussed in light of fabrication of MgO/Heusler based MTJs, where the exponential decay of tunneling probability with contact separation exemplifies the importance of the ferromagnet/tunnel barrier interface.

Reaction path in the formation of titanium diboride by a magnesium thermite process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sundaram, V.; Logan, K.V.; Speyer, R.F.

1995-12-31

TiB{sub 2} was formed by a thermite reaction amongst Mg, amorphous B{sub 2}O{sub 3} and TiO{sub 2} powders. Mixtures consisting of 2Mg-TiO{sub 2}, 3Mg-B{sub 2}O{sub 3} and 5Mg-TiO{sub 2}-B{sub 2}O{sub 3} were heat treated using DTA and separately via ignition with a nichrome wire; product phases were identified using XRD. MgO and Ti were products from the first mixture reacted in argon, whereas an incomplete transformation forming Mg{sub 3}TiO{sub 4} occurred in air. For the second mixture, a reaction forming Mg{sub 3}B{sub 2}O{sup 6} occurred in air, but no reaction occurred in argon due to deficiency of oxygen. Minor amountsmore » Of Mg{sub 3}B{sub 2}O{sub 6} and Mg{sub 2}TiO{sub 4} were detected in addition to the predicted product phases of MgO and TiB{sub 2} for the third mixture ignited both in air and argon. Based on available evidence, a path for this reaction was deduced; Mg particles in contact with TiO{sub 2} reacted to form Ti, which in turn reacted with B{sub 2}O{sub 3} to form TiB{sub 2}. TiB{sub 2} product particles from the reaction in argon had a more faceted appearance than those formed during the reaction in air. This was interpreted to be the result of glassy B{sub 2}O{sub 3} surface layer formation on TiB{sub 2} particles in air.« less

Effect of Mg2Sn Intermetallic on the Grain Refinement in As-cast AM Series Alloy

NASA Astrophysics Data System (ADS)

She, J.; Pan, F. S.; Hu, H. H.; Tang, A. T.; Yu, Z. W.; Song, K.

2015-08-01

In the present work, in order to investigate the grain refinement mechanism of AM containing Sn alloys, the as-cast AM60, AM90 alloys, and the alloys with addition of 1 wt.% Sn were fabricated by traditional casting, respectively. During the solidification of AM + Sn alloys, the morphology of divorced eutectic Mg17Al12 was refined by Mg2Sn intermetallic that served as the heterogeneous nucleation cores. The modified Mg17Al12 effectively restricted the grain growth and resulted in a grain refinement. As a result, the yield strength of as-cast AM alloys was significantly enhanced by addition of Sn, while the ductility also improved. Moreover, the edge-to-edge model was employed to predict the orientation relationship between Mg17Al12 and Mg2Sn.

Multiresidue method for the determination of 77 pesticides in wine using QuEChERS sample preparation and gas chromatography with mass spectrometry.

PubMed

Jiang, Y; Li, X; Xu, J; Pan, C; Zhang, J; Niu, W

2009-06-01

A method based on a QuEChERS (quick, easy, cheap, effective, rugged, safe) sample preparation method and gas chromatography with mass spectrometric detection by selected ion monitoring (GC/MS-SIM) was developed for simultaneous determination of 77 pesticide residues in wine. An extraction of 10 ml of sample with acetonitrile followed by liquid-liquid partition formed by the addition of 4 g MgSO(4) and 3 g NaCl was applied in the sample preparation. The clean-up was carried out by applying dispersive solid-phase with 150 mg MgSO(4) as well as 50 mg primary secondary amine (PSA). One quantitation ion and at least two identification ions were selected in the analytical method for each pesticide compound by GC/MS. The recovery data were obtained by spiking blank samples at two concentration levels (0.05 and 0.2 mg l(-1)). The recoveries of all pesticides were in the range 70-110%, with intra-day precision of less than 15%, and the inter-day precision of less than 22% and 15% for 0.05 and 0.2 mg l(-1) fortification levels, respectively. Linearity was between 0.02 and 2 mg l(-1) with determination coefficients (R(2)) greater than 0.98 for all compounds. The limits of quantification (LOQs) for the 77 pesticides ranged from 0.003 to 0.05 mg l(-1). This method was applied for routine analysis in market products.

Atomic layer deposited ZrO2 nanofilm on Mg-Sr alloy for enhanced corrosion resistance and biocompatibility.

PubMed

Yang, Qiuyue; Yuan, Wei; Liu, Xiangmei; Zheng, Yufeng; Cui, Zhenduo; Yang, Xianjin; Pan, Haobo; Wu, Shuilin

2017-08-01

The biodegradability and good mechanical property of magnesium alloys make them potential biomedical materials. However, their rapid corrosion rate in the human body's environment impairs these advantages and limits their clinical use. In this work, a compact zirconia (ZrO 2 ) nanofilm was fabricated on the surface of a magnesium-strontium (Mg-Sr) alloy by the atomic layer deposition (ALD) method, which can regulate the thickness of the film precisely and thus also control the corrosion rate. Corrosion tests reveal that the ZrO 2 film can effectively reduce the corrosion rate of Mg-Sr alloys that is closely related to the thickness of the film. The cell culture test shows that this kind of ZrO 2 film can also enhance the activity and adhesion of osteoblasts on the surfaces of Mg-Sr alloys. The significance of the current work is to develop a zirconia nanofilm on biomedical MgSr alloy with controllable thickness precisely through atomic layer deposition technique. By adjusting the thickness of nanofilm, the corrosion rate of Mg-Sr alloy can be modulated, thereafter, the degradation rate of Mg-based alloys can be controlled precisely according to actual clinical requirement. In addition, this zirconia nanofilm modified Mg-Sr alloys show excellent biocompatibility than the bare samples. Hence, this work provides a new surface strategy to control the degradation rate while improving the biocompatibility of substrates. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Influence of the metal addition for biohydrogen production from the conversion of palm oil mill effluent (POME) by anaerobic process

NASA Astrophysics Data System (ADS)

Gumilar, Andri; Syafila, Mindriany; Handajani, Marisa

2017-11-01

Biohydrogen is one of the main alternative fuels promising for the future. Bioconversion of the wastewater with the high concentration of organic using biological processes or microorganism by anaerobic processes can produce biogas which can be used as fuel instead of fossil fuels. In this study, palm oil mill effluent (POME) with the concentration of COD is 24,500 mg/L has been used as a substrate. The aim of this study was to determine the effect of metal addition for the formation of biohydrogen. Circulating bed reactor (CBR) is used with the flushing N2 1L/min for 24 hr and continued operates for 72 hr by internal biogas. The additional variation concentration of Fe(II) ion are 0.5; 1.0 and 2.5 mg/L, and Mg(II) are 0.5 and 1.5 mg/L were added by combination. The results showed that the combination of Fe(II) 1.0 mg/L and Mg(II) 1.5 mg/L produced the highest biohydrogen production is 17.12 %v/v and the rate of biohydrogen production is 0.010-0.233 % v/v /hr. Another combination of Fe(II) and Mg(II) provide results for the biohydrogen production is 10.46-16.37 %v/v with the highest rate of biohydrogen production is 0.008-0.278 %v/v/hr.

Effects of Al addition on atomic structure of Cu-Zr metallic glass

NASA Astrophysics Data System (ADS)

Li, Feng; Zhang, Huajian; Liu, Xiongjun; Dong, Yuecheng; Yu, Chunyan; Lu, Zhaoping

2018-02-01

The atomic structures of Cu52Zr48 and Cu45Zr48Al7 metallic glasses (MGs) have been studied by molecular dynamic simulations. The results reveal that the molar volume of the Cu45Zr48Al7 MG is smaller than that of the Cu52Zr48 MG, although the size of the Al atom is larger than that of the Cu atom, implying an enhanced atomic packing density achieved by introducing Al into the ternary MG. Bond shortening in unlike atomic pairs Zr-Al and Cu-Al is observed in the Cu45Zr48Al7 MG, which is attributed to strong interactions between Al and (Zr, Cu) atoms. Meanwhile, the atomic packing efficiency is enhanced by the minor addition of Al. Compared with the Cu52Zr48 binary MG, the potential energy of the ternary MG decreases and the glass transition temperature increases. Structural analyses indicate that more Cu- and Al-centered full icosahedral clusters emerge in the Cu45Zr48Al7 MG as some Cu atoms are substituted by Al. Furthermore, the addition of Al leads to more icosahedral medium-range orders in the ternary MG. The increase of full icosahedral clusters and the enhancement of the packing density are responsible for the improved glass-forming ability of Cu45Zr48Al7.

Fabrication and Characterization of Porous MgAl2O4 Ceramics via a Novel Aqueous Gel-Casting Process

PubMed Central

Yuan, Lei; Liu, Zongquan; Liu, Zhenli; He, Xiao; Ma, Beiyue; Zhu, Qiang; Yu, Jingkun

2017-01-01

A novel and aqueous gel-casting process has been successfully developed to fabricate porous MgAl2O4 ceramics by using hydratable alumina and MgO powders as raw materials and deionized water as hydration agent. The effects of different amounts of deionized water on the hydration properties, apparent porosity, bulk density, microstructure, pore size distribution and compressive strength of the samples were investigated. The results indicated that the porosity and the microstructure of porous MgAl2O4 ceramics were governed by the amounts of deionized water added. The porous structure was formed by the liberation of physisorbed water and the decomposition of hydration products such as bayerite, brucite and boehmite. After determining the addition amounts of deionized water, the fabricated porous MgAl2O4 ceramics had a high apparent porosity (52.5–65.8%), a small average pore size structure (around 1–3 μm) and a relatively high compressive strength (12–28 MPa). The novel aqueous gel-casting process with easy access is expected to be a promising candidate for the preparation of Al2O3-based porous ceramics. PMID:29189734

Prophylactic G-CSF and antibiotics enable a significant dose-escalation of triplet-chemotherapy in non-small cell lung cancer.

PubMed

Timmer-Bonte, J N H; Punt, C J A; vd Heijden, H F M; van Die, C E; Bussink, J; Beijnen, J H; Huitema, A D R; Tjan-Heijnen, V C G

2008-05-01

In advanced non-small cell lung cancer (NSCLC) the clinical benefit of a platinum-based doublet is only modest, therefore, attenuated dosed three-drug combinations are investigated. We hypothesized that with adequate support a full dosed chemotherapy triplet is feasible. The study was designed as a dose finding study of paclitaxel in chemotherapy-naive patients. Paclitaxel was given as a 3-h infusion on day 1, followed by fixed doses of teniposide (or etoposide) 100mg/m(2) days 1, 3, 5 and cisplatin 80 mg/m(2) day 1 every 3 weeks. As myelotoxicity was expected to be the dose-limiting toxicity, prophylactic G-CSF and antibiotic support was evaluated. Indeed, paclitaxel 120 mg/m(2) resulted in dose-limiting neutropenia, despite G-CSF support. Teniposide/etoposide day 1, 3, 5 was less myelotoxic compared to day 1, 2, 3. G-CSF support allowed paclitaxel dose-escalation to 250 mg/m(2). The addition of prophylactic antibiotics enabled dose-escalation to 275 mg/m(2) without reaching MTD. In conclusion, G-CSF and antibiotics prophylaxis enables the delivery of a full dosed chemotherapy triplet in previously untreated NSCLC patients.

Layered Double Hydroxides: Potential Release-on-Demand Fertilizers for Plant Zinc Nutrition.

PubMed

López-Rayo, Sandra; Imran, Ahmad; Bruun Hansen, Hans Chr; Schjoerring, Jan K; Magid, Jakob

2017-10-11

A novel zinc (Zn) fertilizer concept based on Zn-doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthesized, their chemical composition was analyzed, and their nutrient release was studied in buffered solutions with different pH values. Uptake of Zn by barley (Hordeum vulgare cv. Antonia) was evaluated in short- (8 weeks), medium- (11 weeks), and long-term (28 weeks) experiments in quartz sand and in a calcareous soil enriched with Zn-doped Mg-Fe-LDHs. The Zn release rate of the Zn-doped Mg-Fe-LDHs was described by a first-order kinetics equation showing maximum release at pH 5.2, reaching approximately 45% of the total Zn content. The Zn concentrations in the plants receiving the LDHs were between 2- and 9.5-fold higher than those in plants without Zn addition. A positive effect of the LDHs was also found in soil. This work documents the long-term Zn release capacity of LDHs complying with a release-on-demand behavior and serves as proof-of-concept that Zn-doped Mg-Fe-LDHs can be used as Zn fertilizers.

Experimental and numerical study of spatter formation and composition change in fiber laser welding of aluminum alloy

NASA Astrophysics Data System (ADS)

Wu, Dongsheng; Hua, Xueming; Ye, Youxiong; Huang, Lijin; Li, Fang; Huang, Ye

2018-05-01

A laser welding experiment with glass is conducted to directly observe the keyhole behavior and spatter formation in fiber laser welding of aluminum alloy. A 3D model is developed to investigate the spatter formation and composition change. An additional conservation equation is introduced to describe the Mg element distribution, and the Mg element loss due to evaporation is also considered. Based on numerical and experimental results, it is found that the keyhole geometry in laser welding of aluminum alloy is different from that in laser welding of steel. There are three required steps for spatter formation around the keyhole. The high momentum of the molten metal, the high recoil pressure and vapor shear stress, and the low surface tension around the keyhole contribute to the easy formation of spatter. The in-homogeneous distribution of Mg element in the weld can be attributable to the continuous evaporation of Mg element at the top surface of keyhole rear, the upward flow of low Mg element region from the bottom of the keyhole to the top surface of keyhole rear along the fusion line, the collapse of the keyhole, and the ejection of spatters.

Analysis of two commercially available bortezomib products: differences in assay of active agent and impurity profile.

PubMed

Byrn, Stephen R; Tishmack, Patrick A; Milton, Mark J; van de Velde, Helgi

2011-06-01

The analytical properties of two commercially available bortezomib products (VELCADE(®) and Bortenat) were compared using nuclear magnetic resonance, mass spectrometry, high-performance liquid chromatography, and gas chromatography. The data showed differences between the two products. Based on these data, Bortenat samples contained more active ingredients than indicated by the label (mean, 116.5% and 117.9% of label, in 2-mg and 3.5-mg vials, respectively). In comparison, VELCADE samples contained a mean of 99.3% of active ingredient, which was consistent with the approved specification range (US, 90-110%; EU, 95-105%). Clinical data demonstrate that patients exposed to higher than recommended doses of bortezomib on the standard twice-weekly dosing schedule are likely to have an increased risk of major toxicities. Bortenat 2-mg vials contained an isovaleraldehyde impurity; the origin of this is unknown. Additionally, the ratio of boronic acid to boronic ester differed between Bortenat 2 mg (0.27:1) and 3.5 mg (0.13:1) and VELCADE (0.10:1) samples reconstituted in saline indicating that the Bortenat product is not equivalent to the VELCADE product.

Mechanical optimization of the composite biomaterial based on the tricalcium phosphate, titania and magnesium fluoride.

PubMed

Ayadi, Ibticem; Ayed, Foued Ben

2016-07-01

The microstructure, the densification and the mechanical properties of the tricalcium phosphate - titania - MgF2 composites were investigated. The effect of MgF2 addition on the performances of the tricalcium phosphate - 40wt% titania composites is discussed. The mechanical properties were investigated by Brazilian test, Vickers indentation and the ultrasound techniques. The mechanical properties of the tricalcium phosphate - 40wt% titania composites reached optimum performances after the sintering process at 1200°C for one hour with 4wt% MgF2. Thus, the highest values of the rupture strength, Vickers hardness, Young׳s and the shear modulus reached 27MPa, 360Hv, 51GPa and 20GPa, respectively. The increase of the mechanical properties of the composites is due to the presence of the liquid phase and the formation of a new compound. Thus, the microstructure of the composites reveals the presence of a new lamella form relative to the Mg2(PO4)F. Beyond 4wt% MgF2, the performances of the composites are hindered by the exaggerated grain growth and the formation of the bubbles. Copyright © 2016 Elsevier Ltd. All rights reserved.

Selenium and selenium-sulfur cathode materials for high-energy rechargeable magnesium batteries

NASA Astrophysics Data System (ADS)

Zhao-Karger, Zhirong; Lin, Xiu-Mei; Bonatto Minella, Christian; Wang, Di; Diemant, Thomas; Behm, R. Jürgen; Fichtner, Maximilian

2016-08-01

Magnesium (Mg) is an attractive metallic anode material for next-generation batteries owing to its inherent dendrite-free electrodeposition, high capacity and low cost. Here we report a new class of Mg batteries based on both elemental selenium (Se) and selenium-sulfur solid solution (SeS2) cathode materials. Elemental Se confined into a mesoporous carbon was used as a cathode material. Coupling the Se cathode with a metallic Mg anode in a non-nucleophilic electrolyte, the Se cathode delivered a high initial volumetric discharge capacity of 1689 mA h cm-3 and a reversible capacity of 480 mA h cm-3 was retained after 50 cycles at a high current density of 2 C. The mechanistic insights into the electrochemical conversion in Mg-Se batteries were investigated by microscopic and spectroscopic methods. The structural transformation of cyclic Se8 into chainlike Sen upon battery cycling was revealed by ex-situ Raman spectroscopy. In addition, the promising battery performance with a SeS2 cathode envisages the perspective of a series of SeSn cathode materials combining the benefits of both selenium and sulfur for high energy Mg batteries.

Crystallization kinetics of Mg–Cu–Yb–Ca–Ag metallic glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsarkov, Andrey A., E-mail: tsarkov@misis.ru; WPI Advanced Institute for Materials Research, Tohoku University, Katahira 2-1-1, Aoba-Ku, Sendai 980-8577; Zanaeva, Erzhena N.

The paper presents research into a Mg–Cu–Yb system based metallic glassy alloys. Metallic glasses were prepared using induction melting and further injection on a spinning copper wheel. The effect of alloying by Ag and Ca on the glass forming ability and the kinetics of crystallization of Mg–Cu–Yb system based alloys were studied. The differential scanning calorimeter and X-ray diffractometer were used to investigate the kinetics of crystallization and the phase composition of the samples. An indicator of glass forming ability, effective activation energy of crystallization, and enthalpy of mixing were calculated. An increase of the Ca and Ag content hasmore » a positive effect on the glass forming ability, the effective activation energy of crystallization, and the enthalpy of mixing. The highest indicators of the glass forming ability and the thermal stability were found for alloys that contain both alloying elements. The Ag addition suppresses precipitation of the Mg{sub 2}Cu phase during crystallization. A dual-phase glassy-nanocrystalline Mg structure was obtained in Mg{sub 65}Cu{sub 25}Yb{sub 10} and Mg{sub 59.5}Cu{sub 22.9}Yb{sub 11}Ag{sub 6.6} alloys after annealing. Bulk samples with a composite glassy-crystalline structure were obtained in Mg{sub 59.5}Cu{sub 22.9}Yb{sub 11}Ag{sub 6.6} and Mg{sub 64}Cu{sub 21}Yb{sub 9.5}Ag{sub 5.5} alloys. A thermodynamic database for the Mg–Cu–Yb–Ca–Ag system was created to compare the process of crystallization of alloys with polythermal sections of the Mg–Cu–Yb–Ca–Ag phase diagram. - Highlights: • New alloy compositions based on Mg–Cu–Yb system were developed and investigated. • Increasing content of Ag and Ca leads to improving GFA. • Bulk samples with a composite glassy-crystalline structure were obtained. • Thermodynamic database for Mg–Cu–Yb–Ca–Ag system was created.« less

Effects of Sm addition on electromagnetic interference shielding property of Mg-Zn-Zr alloys

NASA Astrophysics Data System (ADS)

Yang, Chubin; Pan, Fusheng; Chen, Xianhua; Luo, Ning

2017-06-01

The electromagnetic interference (EMI) shielding of Sm-containing magnesium alloys in the 30-1500 MHz testing frequency range was investigated by coaxial cable method. The results demonstrated that Mg-3Zn alloys displayed the best electromagnetic shielding property. When 0.5 wt% of Zr was added for crystal grain refinement, the shielding effectiveness (SE) was apparently reduced. The addition of the rare earth element Sm in ZK magnesium alloys can improve the electromagnetic interference shielding of magnesium alloys. The main reason for the differences in electromagnetic interference shielding of magnesium alloys was the change in conductivity. The addition of Zr in Mg-Zn alloys can refine the grains and consequently improve the grain boundary area significantly. Therefore, the number of irregularly arranged atoms at the grain boundaries increased, decreasing the conductivity of magnesium alloys and leading to a decrease in the electromagnetic interference shielding. Following the Sm addition, the Mg-Zn-Sm phase was precipitated at the grain boundaries and in cores. The precipitation of Sm-containing rare earth phases could consume the solid-soluted Zn atoms within the Mg, resulting in an increase in electrical conductivity and electromagnetic interference shielding improvement.

Fabrication of porous MgCo2O4 with rod-like morphology and its superb catalytic activity towards ammonium perchlorate thermal decomposition

NASA Astrophysics Data System (ADS)

Li, Gang; Liu, Xiaoli; Bai, Weiyang

2018-03-01

In this paper, porous MgCo2O4 with rod-like morphology was successfully synthesized through the thermal treatment of metal oxalates precursor originated by the reaction of metal sulfates and oxalic acid, without the addition of other additives. The porous rod-like MgCo2O4, with a diameter of several hundred nanometers and a length of several micrometers, was formed through the agglomeration of numerous crystalline grains sized in 10–25 nm. Its catalytic effect on ammonium perchlorate (AP) thermal decomposition was evaluated using differential scanning calorimetry (DSC) techniques. It was found that the pyrolysis temperature of AP reduced by 129 °C and the heat release increased more than 3.19-fold with a 2 wt% addition of MgCo2O4. Meanwhile, the addition of MgCo2O4 resulted in an AP decomposition activation energy reduction from 216 kJ mol‑1 to 155 kJ mol‑1, calculated using the Kissinger correlation. This study provides new insights into the design and development of high performance catalysts for AP thermal decomposition.

An efficient removal of methyl orange dye from aqueous solution by adsorption onto chitosan/MgO composite: A novel reusable adsorbent

NASA Astrophysics Data System (ADS)

Haldorai, Yuvaraj; Shim, Jae-Jin

2014-02-01

We report a novel multi-functional magnesium oxide (MgO) immobilized chitosan (CS) composite was prepared by chemical precipitation method. The CS-MgO composite was characterized by Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy and zeta potential. The composite was applied as a novel adsorbent for removal of methyl orange model dye and the effect of adsorbent dosage, pH and contact time were studied. The adsorption kinetics followed a pseudo second order reaction. The adsorbent efficiency was unaltered even after five cycles of reuse. In addition, the composite exhibited a superior antibacterial efficacy of 93% within 24 h against Escherichia coli as measured by colony forming units. Based on the data of present investigation the composite being a biocompatible, eco-friendly and low-cost adsorbent with antibacterial activity could find potential applications in variety of fields and in particular environmental applications.

Antireflection coatings based on fluoride formulations for organic solar cells

NASA Astrophysics Data System (ADS)

Suleimanov, S. Kh.; Berger, P.; Dyskin, V. G.; Dzhanklych, M. U.; Bugakov, A. G.; Dudko, O. A.; Kulagina, N. A.; Kim, M.

2016-04-01

An alloy of a mixture of fluorides MgF2 and AlF3 with CaF2 has been obtained in a 3-kW solar furnace. It was supposed that a minor CaF2 additive compensates for the tensile stresses appearing in thin MgF2 and AlF3 films, with their mechanical properties being thereby improved. The results of X-ray phase analysis demonstrated that both components of the mixture are present in the alloy, while the complex oxide CaAl4O7, the formation of which is attributed to the melting in air, is only identified in AlF3: CaF2 = 95: 5 (wt %). The increase in the transmittance of glass and polyethylene terephthalate upon deposition onto their surface of a thin film of the material synthesized in the study is due to the optical properties of AlF3 and MgF2.

Exposure assessment of the population in Poland to the toxic effects of arsenic compounds present in rice and rice based products

PubMed

Mania, Monika; Rebeniak, Małgorzata; Szynal, Tomasz; Starska, Krystyna; Wojciechowska-Mazurek, Maria; Postupolski, Jacek

Rice is a staple food for many people in the world and an important ingredient for production of food for infants and young children. According to European Food Safety Authority (EFSA), cereals, primarily rice and rice products, are an important source of human exposure to inorganic arsenic, which has been classified by the International Agency for Research on Cancer (IARC) as group I carcinogen. Arsenic is present in rice and rice products mainly as an inorganic form being more toxic than organic compounds The aim of the study was to determine the total and inorganic arsenic content in rice, rice-based products including food for infants and young children available on the market in Poland and thus to estimate consumer exposure to inorganic arsenic from these groups of foodstuffs A total of 62 samples of rice and rice products from trade, including a group of rice products for infants and young children, were tested. Contents of total and inorganic arsenic were determined by using hydride generation atomic absorption spectrometry (HGAAS), after dry mineralization of samples and reduction of arsenic to arsenic hydride with sodium borohydride. To extract the inorganic arsenic forms, the samples were subjected to hydrolysis in concentrated HCl and then reduced in the presence of hydrobromic acid and hydrazine sulphate after which triple chloroform extractions and triple 1M HCl re-extractions were performed. Exposure of different groups of populations (adults and children), was estimated in relation to the Benchmark Dose Lower Confidence Limit (BMDL05) as set by the Joint FAO/WHO Expert Committee on Food Additives (JECFA) that resulted in a 0.5% increase in lung cancer (3.0 µg/kg body weight (b.w.) per day) Mean content of total and inorganic arsenic in investigated rice samples was 0.12 mg/kg (median: 0.09 mg/kg; 90th percentile 0.22 mg/kg) and 0.04 mg/kg (median: 0.03 mg/kg, 90th percentile 0.07 mg/kg). Brown rice was found to be more highly contaminated with both total and inorganic arsenic than white rice. Mean contamination of brown rice with total arsenic and inorganic arsenic was: 0.18 mg/kg (median: 0.12 mg/kg, 90th percentile: 0.32 mg/kg) and 0.05 mg/kg (median: 0.05 mg/kg, 90th percentile: 0.07 mg/kg). In turn for the white rice contamination was lower, mean total arsenic content: 0.10 mg/kg (median: 0.08 mg/kg, 90th percentile: 0.19 mg/kg) and mean inorganic arsenic: 0.03 mg/kg (median: 0.03 mg/kg, 90th percentile: 0.06 mg/kg). Contamination of rice-based products both total and inorganic arsenic was similar to those reported for rice, except rice wafers (mean: 0.24 mg/kg and 0.13 mg/kg). In the group of products for infants and young children obtained results were low – mean total arsenic content was 0.06 mg/kg and inorganic arsenic 0.02 mg/kg. The estimated average adult and children’s exposure to inorganic arsenic with rice and rice products was less than 1% of the BMDL05. Intake of inorganic arsenic by 12-month-old infants with ricebased products intended for this group of population was at 6% BMDL05 Based on the obtained results, it was found that the content of total and inorganic arsenic in investigated samples of rice and rice products did not pose a health risk even though contamination levels in some individual samples were significant

Leek yellow stripe virus isolates from Brazil form a distant clade based on the P1 gene

USDA-ARS?s Scientific Manuscript database

The complete genomic sequence of a garlic isolate of Leek yellow stripe virus from Brazil (LYSV-MG) has been determined, and phylogenetic comparisons made to LYSV isolates from other parts of the world. In addition, the nucleotide sequence of the 5'UTR and part of the P1 gene of multiple LYSV isolat...

Concentrations of dissolved solids and nutrients in water sources and selected streams of the Santa Ana Basin, California, Octoger 1998 - September 2001

USGS Publications Warehouse

Kent, Robert; Belitz, Kenneth

2004-01-01

Concentrations of total dissolved solids (TDS) and nutrients in selected Santa Ana Basin streams were examined as a function of water source. The principal water sources are mountain runoff, wastewater, urban runoff, and stormflow. Rising ground water also enters basin streams in some reaches. Data were collected from October 1998 to September 2001 from 6 fixed sites (including a mountain site), 6 additional mountain sites (including an alpine indicator site), and more than 20 synoptic sites. The fixed mountain site on the Santa Ana River near Mentone appears to be a good representative of reference conditions for water entering the basin. TDS can be related to water source. The median TDS concentration in base-flow samples from mountain sites was 200 mg/L (milligrams per liter). Base-flow TDS concentrations from sites on the valley floor typically ranged from 400 to 600 mg/L; base flow to most of these sites is predominantly treated wastewater, with minor contributions of rising ground water and urban runoff. Sparse data suggest that TDS concentrations in urban runoff are about 300 mg/L. TDS concentrations appear to increase on a downstream gradient along the main stem of the Santa Ana River, regardless of source inputs. The major-ion compositions observed in samples from the different sites can be related to water source, as well as to in-stream processes in the basin. Water compositions from mountain sites are categorized into two groups: one group had a composition close to that of the alpine indicator site high in the watershed, and another group had ionic characteristics closer to those in tributaries on the valley floor. The water composition at Warm Creek, a tributary urban indicator site, was highly variable but approximately intermediate to the compositions of the upgradient mountain sites. Water compositions at the Prado Dam and Imperial Highway sites, located 11 miles apart on the Santa Ana River, were similar to one another and appeared to be a mixture of the waters of the upstream sites, Santa Ana River at MWD Crossing, Cucamonga Creek, and Warm Creek. Rainfall usually dilutes stream TDS concentrations. The median TDS concentration in all storm-event discrete samples was 260 mg/L. The median flow-weighted average TDS concentration for stormflow, based on continuous measurement of specific conductance and hydrograph separation of the continuous discharge record, was 190 mg/L. However, stormflow TDS concentrations were variable, and depended on whether the storm was associated with a relatively small or large rainfall event. TDS concentrations in stormflow associated with relatively small events ranged from about 50 to 600 mg/L with a median of 220 mg/L, whereas concentrations in stormflow associated with relatively large events ranged from about 40 to 300 mg/L with a median of 100 mg/L. From the perspective of water managers, the nutrient species of highest concern in Santa Ana Basin streams is nitrate. Most mountain streams had median base-flow concentrations of nitrate below 0.3 mg/L as nitrogen. Nitrate concentrations in both urban runoff and stormflow were near 1 mg/L, which is close to the level found in rainfall for the region. In fact, results from this study suggest that much of the nitrate load in urban storm runoff comes from rainwater. Nitrate concentrations in the Santa Ana River and its major tributaries are highest downstream from wastewater inputs, where median base-flow concentrations of nitrite+nitrate ranged from about 5 to 7 mg/L. About 4 percent of samples collected from sites receiving treated wastewater had nitrate concentrations greater than 10 mg/L. Rising ground water also appears to have high nitrate concentrations (greater than 10 mg/L) in some reaches of the river. Concentrations of other nitrogen species were much lower than nitrate concentrations in base-flow samples. However, storm events increased concentrations and the proportion of organic nitro

Simultaneous determination of five naphthoylindole-based synthetic cannabinoids and metabolites and their deposition in human and rat hair.

PubMed

Kim, Jihyun; Park, Yuran; Park, Meejung; Kim, Eunmi; Yang, Wonkyung; Baeck, Seungkyung; Lee, Sooyeun; Han, Sangbeom

2015-01-01

The continuing appearance of new synthetic cannabinoids has been a major issue in the field of forensic and clinical toxicology. In response to that, analytical methods for synthetic cannabinoids have been increasingly established in a variety of biological matrices. Since most of synthetic cannabinoids with structure similarity share some enzymatic metabolites, making the interpretation of analytical results and the discovery of the parent drug actually ingested very complicated, the investigation on metabolites of the first generation of synthetic cannabinoids with their relatively short side chains in chemical structure could be more important. Therefore, in the present study, we developed the analytical method for AM-2201, JWH-122 and MAM-2201 with JWH-018 as a precursor and their monohydroxylated metabolites in hair matrix. Also, using a rat model, AM-2201 and its monohydroxylated metabolites were identified and then the ratios of metabolite-to-parent drug were estimated to be used as criteria on external contamination. All analytes were extracted with methanol from washed and cut hair samples and the extracts were injected into LC-MS/MS with electrospray ion source in the positive ionization mode. Matrix effect and recovery were evaluated in hair matrices and no significant variations were observed. The validation results for precision and accuracy were satisfactory in both human and rat hair. The LOD and LOQ were 0.5 pg/10mg and 1.0 pg/10mg in human hair and 0.5 pg/20mg and 1.0 pg/20mg in pigmented and non-pigmented rat hair, respectively. Additionally, as a result of the animal study, there were not significant differences in the effect of pigmentation on the distribution of AM-2201 and its monohydroxylated metabolites in hair. Wide variations were observed for the concentrations of the naphthoylindole-based synthetic cannabinoids and metabolites in authentic hair samples from nine cases; those were 0.4-59.2 pg/mg for JWH-018, 0.1-0.8 pg/mg for JWH-073, 1.7-739.0 pg/mg for AM-2201, 0.1-402.0 pg/mg for JWH-122, 0.2-276.0 pg/mg for MAM-2201, 0.2-1.1 pg/mg for JWH-018 N-COOH, 0.3-37.2 pg/mg for JWH-018 N-5-OH, 0.3 pg/mg for JWH-073 N-COOH, 0.4 pg/mg for AM-2201 N-4-OH, 0.2-3.1 pg/mg for AM-2201 N-6-OHindole and 0.1-3.5 pg/mg for JWH-122 N-5-OH. This quantitative LC-MS/MS analytical method for five naphthoylindole-based synthetic cannabinoids and their metabolites was very useful to be applied to authentic hair samples, of which their analytical results suggested the incorporation of synthetic cannabinoids in the hair matrix and provided the information on ingested parent drugs. Copyright © 2014 Elsevier B.V. All rights reserved.

The relationship between proton pump inhibitor use and serum magnesium concentration among hemodialysis patients: a cross-sectional study.

PubMed

Misra, Paraish S; Alam, Ahsan; Lipman, Mark L; Nessim, Sharon J

2015-08-13

Observational data suggest that serum magnesium (Mg) concentration is inversely related to vascular calcification and hyperparathyroidism among patients with end-stage renal disease (ESRD). In recent years, there have been several case reports of hypomagnesemia due to use of proton-pump inhibitors (PPI), with the hypomagnesemia attributed to inappropriate gastrointestinal (GI) Mg loss. We hypothesized that the tendency to GI Mg loss is more common than is currently reported. Since patients with ESRD have little to no renal Mg loss to affect serum Mg concentration, dialysis patients are an interesting population in whom to study the relationship between PPI use and serum Mg levels. Using a single-center cross-sectional design, we studied 155 prevalent hemodialysis (HD) patients. Serum Mg concentration for each patient was determined based on the mean of 3 consecutive serum Mg levels drawn at 6 week intervals. PPI use at the time of the blood tests was documented. The relationship between PPI use and Mg concentration was determined in unadjusted analyses, as well as after adjustment for age, gender, race, cause of ESRD, diabetes, time on HD and dialysate Mg concentration. 55 % of patients were on PPIs at the time of the study. The majority of patients (62 %) used a dialysate Mg (in mmol/L) of 0.5, and the remainder (38 %) used a dialysate Mg of 0.375. Serum Mg levels were significantly lower among PPI users vs. non-users (0.93 vs. 1.02 mmol/L, p < 0.001). This finding persisted after stratifying for dialysate Mg concentration, and after multivariable adjustment (p < 0.001). In addition, more PPI users vs. non-users had a Mg level < 1 mmol/L (79 % vs. 43 %) and a Mg level < 0.8 mmol/L (16 % vs. 4 %). There was a non-significant trend toward increased time on PPI being associated with lower serum Mg levels (p = 0.067). Among HD patients, PPI users have lower serum Mg levels as compared with non-users. Further research is required to determine whether the magnitude of change in Mg levels among PPI users is associated with adverse outcomes.

Synthesis of Two Coumarin-Derived Schiff Bases and Investigation of theirs Selectivity for Zn2.

PubMed

Fan, Long

2017-07-01

In this study, the coumarin-derived schiff bases (HL 1 and HL 2 ) have been designed and synthesized. Upon the addition of Zn 2+ , both of them show significant fluorescence enhancement owing to inhibits PET and ESIPT process respectively. However, the receptor HL 2 response toward Cd 2+ , Mg 2+ , Ba 2+ , Ca 2+ besides Zn 2+ and exhibits fluorescence enhancement but not enough to detection of the concentration levels of Zn 2+ .

Ultra-Lightweight Resistive Switching Memory Devices Based on Silk Fibroin.

PubMed

Wang, Hong; Zhu, Bowen; Wang, Hua; Ma, Xiaohua; Hao, Yue; Chen, Xiaodong

2016-07-01

Ultra-lightweight resistive switching memory based on protein has been demonstrated. The memory foil is 0.4 mg cm(-2) , which is 320-fold lighter than silicon substrate, 20-fold lighter than office paper and can be sustained by a human hair. Additionally, high resistance OFF/ON ratio of 10(5) , retention time of 10(4) s, and excellent flexibility (bending radius of 800 μm) have been achieved. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of Yttrium Addition on Microstructure and Mechanical Properties of AZ80-2Sn Magnesium Alloys

NASA Astrophysics Data System (ADS)

Xue, Hansong; Yang, Gang; Li, Di; Xing, Zhihui; Pan, Fusheng

2015-12-01

The effects of Y on microstructure and mechanical properties of as-cast AZ80-2Sn magnesium alloys were investigated by optical microscopy, scanning electron microscopy and X-ray diffraction. Y addition not only changes the as-cast microstructure but also influences the mechanical properties of AZ80-2Sn alloy. Unmodified AZ80-2Sn alloys under casting state show that Mg17Al12 eutectic phase is semicontinuous and reticulated shape and distributes mainly at grain boundaries. Moreover, there are numerous Mg2Sn precipitate particles dispersing in Mg17Al12 eutectic phases. Y addition to as-cast AZ80-2Sn alloys has an important influence on the precipitation phase. But there has no obvious effect on grain refinement with Y addition. The results show that the AZ80-2Sn alloys with variable Y contents all contain Al2Y phase. By adding Y, the amount of Mg17Al12 is decreased and the dimension of that is reduced. Mg17Al12 eutectic phase turns to discontinuous, and the more disperse phases occur with the increase of Y content. The tensile tests indicate that a minor addition of Y can contribute to the formation of the dispersed small polygonal Al2Y particles and the improvement in the room-temperature strength. However, excessive Y addition leads to the coarsening of Al2Y phases, and thus results in the decline of strength and ductility.

Role of Y2O3, CaO, MgO additives on structural and microstructural behavior of zirconia/mullite aggregates

NASA Astrophysics Data System (ADS)

Mishra, D. K.; Prusty, Sasmita; Mohapatra, B. K.; Singh, S. K.; Behera, S. N.

2012-07-01

Zirconia mullite (MUZ), Y2O3-MUZ, CaO-MUZ and MgO-MUZ composites, synthesized through plasma fusion technique, are becoming important due to their commercial scale of production within five minutes of plasma treatment from sillimanite, zircon and alumina mixture. The X-ray diffraction studies reveal the monoclinic zirconia phase in MUZ composite whereas mixed monoclinic, tetragonal and cubic phases of zirconia have been observed in Y2O3, CaO, MgO added MUZ composites. The Y2O3, CaO and MgO additives act as sintering aids to favour the transformation and stabilisation of tetragonal and cubic zirconia phases at room temperature. These additives also play a key role in the development of various forms of microstructure to achieve dense MUZ composites.

A multicenter hospital-based diagnosis study of automated breast ultrasound system in detecting breast cancer among Chinese women.

PubMed

Zhang, Xi; Lin, Xi; Tan, Yanjuan; Zhu, Ying; Wang, Hui; Feng, Ruimei; Tang, Guoxue; Zhou, Xiang; Li, Anhua; Qiao, Youlin

2018-04-01

The automated breast ultrasound system (ABUS) is a potential method for breast cancer detection; however, its diagnostic performance remains unclear. We conducted a hospital-based multicenter diagnostic study to evaluate the clinical performance of the ABUS for breast cancer detection by comparing it to handheld ultrasound (HHUS) and mammography (MG). Eligible participants underwent HHUS and ABUS testing; women aged 40-69 years additionally underwent MG. Images were interpreted using the Breast Imaging Reporting and Data System (BI-RADS). Women in the BI-RADS categories 1-2 were considered negative. Women classified as BI-RADS 3 underwent magnetic resonance imaging to distinguish true- and false-negative results. Core aspiration or surgical biopsy was performed in women classified as BI-RADS 4-5, followed by a pathological diagnosis. Kappa values and agreement rates were calculated between ABUS, HHUS and MG. A total of 1,973 women were included in the final analysis. Of these, 1,353 (68.6%) and 620 (31.4%) were classified as BI-RADS categories 1-3 and 4-5, respectively. In the older age group, the agreement rate and Kappa value between the ABUS and HHUS were 94.0% and 0.860 (P<0.001), respectively; they were 89.2% and 0.735 (P<0.001) between the ABUS and MG, respectively. Regarding consistency between imaging and pathology results, 78.6% of women classified as BI-RADS 4-5 based on the ABUS were diagnosed with precancerous lesions or cancer; which was 7.2% higher than that of women based on HHUS. For BI-RADS 1-2, the false-negative rates of the ABUS and HHUS were almost identical and were much lower than those of MG. We observed a good diagnostic reliability for the ABUS. Considering its performance for breast cancer detection in women with high-density breasts and its lower operator dependence, the ABUS is a promising option for breast cancer detection in China.

A randomised study of tailored toxicity-based dosage of fluorouracil-epirubicin-cyclophosphamide chemotherapy for early breast cancer (SBG 2000-1).

PubMed

Lindman, H; Andersson, M; Ahlgren, J; Balslev, E; Sverrisdottir, A; Holmberg, S B; Bengtsson, N O; Jacobsen, E H; Jensen, A B; Hansen, J; Tuxen, M K; Malmberg, L; Villman, K; Anderson, H; Ejlertsen, B; Bergh, J; Blomqvist, C

2018-05-01

Retrospective studies have demonstrated a worse outcome in breast cancer patients not developing leukopenia during adjuvant chemotherapy. The SBG 2000-1 is the first randomised trial designed to compare individually dosed chemotherapy without G-CSF support based on grade of toxicity to standard-dosed chemotherapy based on body surface area (BSA). Patients with early breast cancer were included and received the first cycle of standard FEC (fluorouracil 600 mg/m 2 , epirubicin 60 mg/m 2 , cyclophosphamide 600 mg/m 2 ). Patients with nadir leukopenia grade 0-2 after first cycle were randomised between either 6 additional courses of tailored FEC with increased doses (E 75-90 mg/m 2 , C 900-1200 mg/m 2 ) or fixed treatment with 6 standard FEC. Patients with grade 3-4 leukopenia were registered and treated with 6 standard FEC. Primary end-point was distant disease-free survival (DDFS). The study enrolled 1535 patients, of which 1052 patients were randomised to tailored FEC (N = 524) or standard FEC (N = 528), whereas 401 patients with leukopenia grade 3-4 continued standard FEC and formed the registered cohort. Dose escalation did not statistically significantly improve 10-year DDFS (79% and 77%, HR 0.87, CI 0.67-1.14, P = 0.32) or OS (82% and 78%, respectively, HR 0.89, CI 0.57-1.16, P = 0.38). Corresponding estimates for the registered group of patients were DDFS 79% and OS 82%, respectively. The SBG 2000-1 study failed to show a statistically significant improvement of escalated and tailored-dosed chemotherapy compared with standard BSA-based chemotherapy in patients with low haematological toxicity, although all efficacy parameters showed a numerical advantage for tailored treatment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Lethal and sublethal effects of chlorine, phenol, and chlorine-phenol mixtures on the mud crab, Panopeus herbstii.

PubMed

Key, P B; Scott, G I

1986-11-01

The mud crab, Panopeus herbstii, was acutely exposed (96-hr) to chlorine-produced oxidants (CPO), phenol, and a CPO-phenolic mixture (1:1) to determine lethal and sublethal effects. The 96-hr (LC50) values were determined for each individual compound and mixture. Additionally, whole-animal respiration rates were measured following acute exposure to sublethal concentrations of each compound or mixture. Phenol uptake/depuration rates were measured in the phenol and CPO-phenol mixture concentrations. Results indicated 96-hr LC50 values of 1.06 mg/L for CPO (fiducial limits (FL) = 0.53-2.01 mg/L), 52.8 mg/L for phenol (FL = 45.6-64.5 mg/L), and 184.7 mg/L total toxicant units (TTU) for the CPO-phenol mixture (FL = 143.7-250.2 mg/L TTU). Statistical analysis indicated that the acute toxicity of the CPO-phenol mixture was less than additive. Sublethal studies indicated that only acute exposure to sublethal concentrations of CPO caused altered respiration rates. After 96-hr depuration, metabolic rates in all CPO-exposure crabs generally returned to control rates. Uptake/depuration rate studies indicated significantly lower phenol uptake rates in crabs exposed to the CPO-phenol mixture. These findings suggest that the less-than-additive toxicity of the CPO-phenol mixture may result from lowered uptake/depuration rate kinetics and indicate that the discharge of chlorinated-phenolic waste may not result in additive and/or synergistic interactions, but rather in less-than-additive effects on decapod aquatic species.

Microstructure and corrosion behavior of coated AZ91 alloy by microarc oxidation for biomedical application

NASA Astrophysics Data System (ADS)

Wang, Y. M.; Wang, F. H.; Xu, M. J.; Zhao, B.; Guo, L. X.; Ouyang, J. H.

2009-08-01

Magnesium and its alloy currently are considered as the potential biodegradable implant materials, while the accelerated corrosion rate in intro environment leads to implant failure by losing the mechanical integrity before complete restoration. Dense oxide coatings formed in alkaline silicate electrolyte with and without titania sol addition were fabricated on magnesium alloy using microarc oxidation process. The microstructure, composition and degradation behavior in simulated body fluid (SBF) of the coated specimens were evaluated. It reveals that a small amount of TiO 2 is introduced into the as-deposited coating mainly composed of MgO and Mg 2SiO 4 by the addition of titania sol into based alkaline silicate electrolytic bath. With increasing concentration of titania sol from 0 to 10 vol.%, the coating thickness decreases from 22 to 18 μm. Electrochemical tests show that the Ecorr of Mg substrate positively shifted about 300˜500 mV and icorr lowers more than 100 times after microarc oxidation. However, the TiO 2 modified coatings formed in electrolyte containing 5 and 10 vol.% titania sol indicate an increasing worse corrosion resistance compared with that of the unmodified coating, which is possibly attributed to the increasing amorphous components caused by TiO 2 involvement. The long term immersing test in SBF is consistent with the electrochemical test, with the coated Mg alloy obviously slowing down the biodegradation rate, meanwhile accompanied by the increasing damage trends in the coatings modified by 5 and 10 vol.% titania sol.

Biogenic Silver for Disinfection of Water Contaminated with Viruses▿

PubMed Central

De Gusseme, Bart; Sintubin, Liesje; Baert, Leen; Thibo, Ellen; Hennebel, Tom; Vermeulen, Griet; Uyttendaele, Mieke; Verstraete, Willy; Boon, Nico

2010-01-01

The presence of enteric viruses in drinking water is a potential health risk. Growing interest has arisen in nanometals for water disinfection, in particular the use of silver-based nanotechnology. In this study, Lactobacillus fermentum served as a reducing agent and bacterial carrier matrix for zerovalent silver nanoparticles, referred to as biogenic Ag0. The antiviral action of biogenic Ag0 was examined in water spiked with an Enterobacter aerogenes-infecting bacteriophage (UZ1). Addition of 5.4 mg liter−1 biogenic Ag0 caused a 4.0-log decrease of the phage after 1 h, whereas the use of chemically produced silver nanoparticles (nAg0) showed no inactivation within the same time frame. A control experiment with 5.4 mg liter−1 ionic Ag+ resulted in a similar inactivation after 5 h only. The antiviral properties of biogenic Ag0 were also demonstrated on the murine norovirus 1 (MNV-1), a model organism for human noroviruses. Biogenic Ag0 was applied to an electropositive cartridge filter (NanoCeram) to evaluate its capacity for continuous disinfection. Addition of 31.25 mg biogenic Ag0 m−2 on the filter (135 mg biogenic Ag0 kg−1 filter medium) caused a 3.8-log decline of the virus. In contrast, only a 1.5-log decrease could be obtained with the original filter. This is the first report to demonstrate the antiviral efficacy of extracellular biogenic Ag0 and its promising opportunities for continuous water disinfection. PMID:20038697

Impact of initial catalyst form on the 3D structure and performance of ball-milled Ni-catalyzed MgH 2 for hydrogen storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

House, Stephen D.; Vajo, John J.; Ren, Chai

Although it has been shown that the hydrogen storage kinetics of metal hydrides can be significantly improved by the addition of transition metal-based catalysts, relatively little attention has been paid to the impact that the form in which these catalysts are introduced during synthesis has on the resulting structure and how this alters performance. Two mixtures of MgH 2 doped with Ni were prepared via high-energy ball-milling under identical conditions, one using a pure Ni nanopowder catalyst and the other using anhydrous NiCl 2. The resulting Ni catalyst particles of the NiCl 2-doped material were 10-100 times smaller, as wellmore » as more uniform in size and shape. Electron tomography revealed that the additive form also altered its incorporation and 3D spatial distribution, with Ni particles limited to the outer surface in the NiCl 2-doped case. The significantly lower desorption performance measured in the NiCl 2-doped material is attributed to regions of MgCl 2 acting as barriers between the MgH 2 and Ni, hindering the ability of the latter to effectively catalyze the reactions. Finally, this work demonstrates the hazards in assuming different catalyst forms produce similar final structures and highlights the potential of catalyst form as a synthesis tool for optimizing the material structure and performance.« less

Impact of initial catalyst form on the 3D structure and performance of ball-milled Ni-catalyzed MgH 2 for hydrogen storage

DOE PAGES

House, Stephen D.; Vajo, John J.; Ren, Chai; ...

2017-02-24

Although it has been shown that the hydrogen storage kinetics of metal hydrides can be significantly improved by the addition of transition metal-based catalysts, relatively little attention has been paid to the impact that the form in which these catalysts are introduced during synthesis has on the resulting structure and how this alters performance. Two mixtures of MgH 2 doped with Ni were prepared via high-energy ball-milling under identical conditions, one using a pure Ni nanopowder catalyst and the other using anhydrous NiCl 2. The resulting Ni catalyst particles of the NiCl 2-doped material were 10-100 times smaller, as wellmore » as more uniform in size and shape. Electron tomography revealed that the additive form also altered its incorporation and 3D spatial distribution, with Ni particles limited to the outer surface in the NiCl 2-doped case. The significantly lower desorption performance measured in the NiCl 2-doped material is attributed to regions of MgCl 2 acting as barriers between the MgH 2 and Ni, hindering the ability of the latter to effectively catalyze the reactions. Finally, this work demonstrates the hazards in assuming different catalyst forms produce similar final structures and highlights the potential of catalyst form as a synthesis tool for optimizing the material structure and performance.« less

Investigation of antioxidant properties of metal ascorbates and their mixtures by voltammetry

NASA Astrophysics Data System (ADS)

Vtorushina, A. N.; Nikonova, E. D.

2015-04-01

The paper describes modern ways for selection of anti-radical substances. Molding of such components with a carbon-based material decreases the rate of its oxidative destruction. Addition of such a component to a carbon-based material decreases the rate of its oxidative destruction. The purpose of this study is to determine the antioxidant activity of ascorbates metals (Ca, Mg, Li, Co, Fe), used in the practice of medicine, as well as mixtures based on them together with well-known antioxidants. In this article we examine the effect of metals on the process of ascorbate oxygen electroreduction. From these ascorbates lithium and magnesium ascorbate showed the greatest activity toward cathode oxygen reduction process. Also mixtures with well-known examined antioxidants ascorbate (glucose, dihydroquercetin) were investigated at different concentrations of components. It is shown that the multicomponent mixtures exhibit lower activity than the individual drugs. Recommended the creation of drugs on the basis of ascorbate Mg and Li with not more than 3 number of components.

Chemical state of chromium in sewage sludge ash based phosphorus-fertilisers.

PubMed

Vogel, Christian; Adam, Christian; Kappen, Peter; Schiller, Tara; Lipiec, Ewelina; McNaughton, Don

2014-05-01

Sewage sludge ash (SSA) based P-fertilisers were produced by thermochemical treatment of SSA with Cl-donors at approximately 1000°C. During this thermochemical process heavy metals are separated as heavy metal chlorides via the gas phase. Chromium cannot be separated under normal conditions. The risk of the development of toxic Cr(VI) during the thermochemical process was investigated. X-ray Absorption Spectroscopy measurements showed that SSA and thermochemically treated SSA with CaCl2, MgCl2 and NaCl contain Cr(III) compounds only. In contrast, treating SSA with elevated quantities of Na2CO3, to enhance the plant-availability of the phosphate phases of the fertiliser, developed approximately 10-15% Cr(VI). Furthermore, Raman microspectroscopy showed that using Mg-carbonate reduces the risk of a Cr(VI) development during thermochemical treatment. Additionally, leaching tests showed that only a Cr-water solubility>10% is an indicator for Cr(VI) in SSA based P-fertilisers. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation of Diatomite Supported Nano Zinc Oxide Composite Photocatalytic Material and Study on its Formaldehyde Degradation

NASA Astrophysics Data System (ADS)

Xiao, Liguang; Pang, Bo

2017-09-01

This experiment used zinc nitrate as precursor, ethanol as solvent and polyethylene glycol as dispersant, diatomite as carrier, diatomite loaded nano Zinc Oxide was prepared by sol-gel method, in addition, the formaldehyde degradation was studied by two kinds of experimental methods: preparation and loading, preparation and post loading, The samples were characterized by SEM, XRD, BET and IR. Experimental results showed that: Diatomite based nano Zinc Oxide had a continuous adsorption and degradation of formaldehyde, formaldehyde gas with initial concentration was 0.7mg/m3, after 36h degradation, the concentration reached 0.238mg/m3, the degradation rate reached to 66%.

Characterization of hydraulic fracturing flowback water in Colorado: implications for water treatment.

PubMed

Lester, Yaal; Ferrer, Imma; Thurman, E Michael; Sitterley, Kurban A; Korak, Julie A; Aiken, George; Linden, Karl G

2015-04-15

A suite of analytical tools was applied to thoroughly analyze the chemical composition of an oil/gas well flowback water from the Denver-Julesburg (DJ) basin in Colorado, and the water quality data was translated to propose effective treatment solutions tailored to specific reuse goals. Analysis included bulk quality parameters, trace organic and inorganic constituents, and organic matter characterization. The flowback sample contained salts (TDS=22,500 mg/L), metals (e.g., iron at 81.4 mg/L) and high concentration of dissolved organic matter (DOC=590 mgC/L). The organic matter comprised fracturing fluid additives such as surfactants (e.g., linear alkyl ethoxylates) and high levels of acetic acid (an additives' degradation product), indicating the anthropogenic impact on this wastewater. Based on the water quality results and preliminary treatability tests, the removal of suspended solids and iron by aeration/precipitation (and/or filtration) followed by disinfection was identified as appropriate for flowback recycling in future fracturing operations. In addition to these treatments, a biological treatment (to remove dissolved organic matter) followed by reverse osmosis desalination was determined to be necessary to attain water quality standards appropriate for other water reuse options (e.g., crop irrigation). The study provides a framework for evaluating site-specific hydraulic fracturing wastewaters, proposing a suite of analytical methods for characterization, and a process for guiding the choice of a tailored treatment approach. Copyright © 2015 Elsevier B.V. All rights reserved.

Galantamine is a novel post-exposure therapeutic against lethal VX challenge.

PubMed

Hilmas, Corey J; Poole, Melissa J; Finneran, Kathryn; Clark, Matthew G; Williams, Patrick T

2009-10-15

The ability of galantamine hydrobromide (GAL HBr) treatment to antagonize O-ethyl-S-(2-diisopropylaminoethyl) methylphosphonothiolate (VX)-induced lethality, impairment of muscle tension, and electroencephalographic (EEG) changes was assessed in guinea pigs. Guinea pigs were challenged with 16.8 microg/kg VX (2LD50). One min after challenge, animals were administered 0.5 mg/kg atropine sulfate (ATR) and 25 mg/kg pyridine-2-aldoxime methochloride (2-PAM). In addition, guinea pigs were given 0, 1, 2, 4, 8 or 10 mg/kg GAL as a post-exposure treatment immediately prior to ATR and 2-PAM. Animals were either monitored for 24-h survival, scheduled for electroencephalography (EEG) recording, or euthanized 60 min later for measurement of indirectly-elicited muscle tension in the hemidiaphragm. Post-exposure GAL therapy produced a dose-dependent increase in survival from lethal VX challenge. Optimal clinical benefits were observed in the presence of 10 mg/kg GAL, which led to 100% survival of VX-challenged guinea pigs. Based on muscle physiology studies, GAL post-exposure treatment protected the guinea pig diaphragm, the major effector muscle of respiration, from fatigue, tetanic fade, and muscular paralysis. Protection against the paralyzing effects of VX was dose-dependent. In EEG studies, GAL did not alter seizure onset for all doses tested. At the highest dose tested (10 mg/kg), GAL decreased seizure duration when administered as a post-exposure treatment 1 min after VX. GAL also reduced the high correlation associated between seizure activity and lethality after 2LD50 VX challenge. GAL may have additional benefits both centrally and peripherally that are unrelated to its established mechanism as a reversible acetylcholinesterase inhibitor (AChEI).

Effects of MDMA Injections on the Behavior of Socially-Housed Long-Tailed Macaques (Macaca fascicularis).

PubMed

Ballesta, Sébastien; Reymond, Gilles; Pozzobon, Matthieu; Duhamel, Jean-René

2016-01-01

3,4-methylenedioxy-N-methyl amphetamine (MDMA) is one of the few known molecules to increase human and rodent prosocial behaviors. However, this effect has never been assessed on the social behavior of non-human primates. In our study, we subcutaneously injected three different doses of MDMA (1.0, 1.5 or 2.0mg/kg) to a group of three, socially housed, young male long-tailed macaques. More than 200 hours of behavioral data were recorded, during 68 behavioral sessions, by an automatic color-based video device that tracked the 3D positions of each animal and of a toy. This data was then categorized into 5 exclusive behaviors (resting, locomotion, foraging, social contact and object play). In addition, received and given social grooming was manually scored. Results show several significant dose-dependent behavioral effects. At 1.5mg/kg only, MDMA induces a significant increase in social grooming behavior, thus confirming the prosocial effect of MDMA in macaques. Additionally, at 1.5 and 2.0 mg/kg MDMA injection substantially decreases foraging behavior, which is consistent with the known anorexigenic effect of this compound. Furthermore, at 2.0 mg/kg MDMA injection induces an increase in locomotor behavior, which is also in accordance with its known stimulant property. Interestingly, MDMA injected at 1.0mg/kg increases the rate of object play, which might be interpreted as a decrease of the inhibition to manipulate a unique object in presence of others, or, as an increase of the intrinsic motivation to manipulate this object. Together, our results support the effectiveness of MDMA to study the complex neurobiology of primates' social behaviors.

Influence of iron precipitated condition and light intensity on microalgae activated sludge based wastewater remediation.

PubMed

Anbalagan, Anbarasan; Schwede, Sebastian; Lindberg, Carl-Fredrik; Nehrenheim, Emma

2017-02-01

The indigenous microalgae-activated sludge (MAAS) process during remediation of municipal wastewater was investigated by studying the influence of iron flocculation step and light intensity. In addition, availability of total phosphorous (P) and photosynthetic activity was examined in fed-batch and batch mode under northern climatic conditions and limited lighting. This was followed by a semi-continuous operation with 4 d of hydraulic retention time and mean cell residence time of 6.75 d in a photo-bioreactor (PBR) with varying P availability. The fed-batch condition showed that P concentrations of 3-4 mg L -1 were effective for photosynthetic chl. a development in iron flocculated conditions. In the PBR, the oxygen evolution rate increased with increase in the concentration of MAAS (from 258 to 573 mg TSS L -1 ) at higher surface photosynthetic active radiation (250 and 500 μmol m -2 s -1 ). Additionally, the rate approached a saturation phase at low MAAS (110 mg L -1 ) with higher light intensities. Semi-continuous operation with luxury P uptake and effective P condition showed stable average total nitrogen removal of 88 and 92% respectively, with residual concentrations of 3.77 and 2.21 mg L -1 . The corresponding average P removal was 68 and 59% with residual concentrations of 2.32 and 1.75 mg L -1 . The semi-continuous operation produced a rapidly settleable MAAS under iron flocculated condition with a settling velocity of 92-106 m h -1 and sludge volume index of 31-43 ml g -1 in the studied cases. Copyright © 2016 Elsevier Ltd. All rights reserved.

Galantamine is a novel post-exposure therapeutic against lethal VX challenge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hilmas, Corey J.; Poole, Melissa J.; Finneran, Kathryn

2009-10-15

The ability of galantamine hydrobromide (GAL HBr) treatment to antagonize O-ethyl-S-(2-diisopropylaminoethyl) methylphosphonothiolate (VX)-induced lethality, impairment of muscle tension, and electroencephalographic (EEG) changes was assessed in guinea pigs. Guinea pigs were challenged with 16.8 {mu}g/kg VX (2LD50). One min after challenge, animals were administered 0.5 mg/kg atropine sulfate (ATR) and 25 mg/kg pyridine-2-aldoxime methochloride (2-PAM). In addition, guinea pigs were given 0, 1, 2, 4, 8 or 10 mg/kg GAL as a post-exposure treatment immediately prior to ATR and 2-PAM. Animals were either monitored for 24-h survival, scheduled for electroencephalography (EEG) recording, or euthanized 60 min later for measurement of indirectly-elicitedmore » muscle tension in the hemidiaphragm. Post-exposure GAL therapy produced a dose-dependent increase in survival from lethal VX challenge. Optimal clinical benefits were observed in the presence of 10 mg/kg GAL, which led to 100% survival of VX-challenged guinea pigs. Based on muscle physiology studies, GAL post-exposure treatment protected the guinea pig diaphragm, the major effector muscle of respiration, from fatigue, tetanic fade, and muscular paralysis. Protection against the paralyzing effects of VX was dose-dependent. In EEG studies, GAL did not alter seizure onset for all doses tested. At the highest dose tested (10 mg/kg), GAL decreased seizure duration when administered as a post-exposure treatment 1 min after VX. GAL also reduced the high correlation associated between seizure activity and lethality after 2LD50 VX challenge. GAL may have additional benefits both centrally and peripherally that are unrelated to its established mechanism as a reversible acetylcholinesterase inhibitor (AChEI)« less

Efficacy and safety of additional 200-mg dose of celecoxib in adult patients with postoperative pain following extraction of impacted third mandibular molar: a multicenter, randomized, double-blind, placebo-controlled, phase II study in Japan.

PubMed

Saito, Ken'ichi; Kaneko, Akihiro; Machii, Katsuyuki; Ohta, Hiroyoshi; Ohkura, Masayuki; Suzuki, Makoto

2012-02-01

Although third mandibular molar extraction is a widely used and validated model of acute pain for evaluating analgesic efficacy, a large proportion of patients experience moderate or severe pain following this procedure and require analgesia. Current treatment options have been associated with safety concerns and alternative therapies are sought. Our aim was to assess the efficacy and safety of an additional 200-mg dose of celecoxib, administered 5 to 12 hours after an initial 400-mg dose of the drug for the treatment of moderate or severe acute pain following extraction of an impacted third mandibular molar. This was a multicenter, randomized, double-blind, placebo-controlled, Phase II study. Patients experiencing moderate or severe pain within 1 to 2 hours following extraction of an impacted third mandibular molar received an initial 400-mg dose of celecoxib. Patients requiring additional analgesia were subsequently randomized to receive either an additional 200-mg dose of celecoxib or placebo 5 to 12 hours after the initial dose. The study was designed and conducted by Pfizer Inc. for approval of celecoxib in Japan for the indication of acute pain. The primary end point was the patient's impression of efficacy (4-category global evaluation scale). Secondary efficacy end points included pain intensity on a 4-category pain intensity scale, pain intensity on a 100-mm visual analog scale (VAS), and the pain intensity difference (100-mm VAS). In an exploratory analysis, use of rescue medication was evaluated. Primary and secondary end points were analyzed using the full analysis set. Assessment of the safety profile included a physical examination, measurement of pulse rate and blood pressure, standard 12-lead ECG, and laboratory tests. A total of 69 patients (celecoxib, 42/64 [65.6%]; placebo, 27/58 [46.6%]) received the additional dose of study medication; all completed the study without the need for rescue medication. A significantly higher proportion of patients in the celecoxib 200 mg group (41/64 [64.1%]) compared with the placebo group (15/58 [25.9%]) rated the study medication as "good" or "excellent" ≥ 2 hours after the additional dose (P < 0.0001). Pain intensity (VAS) 2 hours after the additional dose was significantly higher in the placebo group than in the celecoxib 200 mg group (P = 0.0003). The reduction in pain intensity from baseline to 2 hours after the additional dose of study medication was also significantly greater in the celecoxib 200 mg group than in the placebo group (P < 0.0001). The incidence of treatment-related, all-cause adverse events was slightly lower in patients receiving celecoxib 200 mg (20.3%) compared with placebo (31.0%). Overall, an additional 200-mg dose of celecoxib was well tolerated and efficacious in reducing the pain associated with extraction of an impacted third mandibular molar in the study population. ClinicalTrials.gov identifier: NCT01062113. Copyright © 2012 Elsevier HS Journals, Inc. All rights reserved.

Characteristics of wet dissolved carbon deposition in a semi-arid catchment at the Loess Plateau, China

NASA Astrophysics Data System (ADS)

Wang, Linhua; Yen, Haw; Chen, Liding; E, Xinhui; Wang, Yafeng

2018-06-01

Wet dissolved carbon deposition is a critical node of the global carbon cycle, but little is known about dissolved organic and inorganic carbon (DOC and DIC) concentrations and fluxes in the semi-arid areas of the Loess Plateau Region (LPR). In this study, we measured variations in DOC and DIC concentrations in rainfalls at Yangjuangou Ecological Restoration and Soil and Water Observatory. Rainwater samples were collected in 16 rainfall events from July to September and the event-based, monthly concentrations and fluxes of DOC and DIC were quantified. The results showed that the event-based concentrations and fluxes of DOC and DIC were highly variable, ranging from 0.56 to 28.71 mg C L-1 and from 3.47 to 17.49 mg C L-1, respectively. The corresponding event-based fluxes ranged from 0.21-258.36 mg C m-2 and from 4.12 to 42.32 mg C m-2. The monthly concentrations of DOC and DIC were 24.62 and 4.30 (July), 3.58 and 10.52 (August), and 1.01 and 5.89 (September) mg C L-1, respectively. Thus, the monthly deposition fluxes of DOC and DIC were 541.64/94.60, 131.03/385.03, and 44.44/259.16 mg C m-2 for July, August, and September, respectively. In addition, the concentrations of DOC and DIC for the concentrated rainfall season (July-September) in the studied catchment were 7.06 and 7.00 mg C L-1, respectively. The estimated annual wet dissolved carbon depositions were 1.91 and 1.89 g C m-2 yr-1 for DOC and DIC, respectively. The results of this study suggest the variation in concentrations and fluxes of DOC and DIC and explore that these variation may be related to the dissolved carbon source and the rainfall characteristics during the concentrated rainfall season in the semi-arid catchment of the LPR. Furthermore, these results also suggest that dissolved carbon may be an important external input of carbon into terrestrial ecosystems.

Zeolite-based hemostat QuikClot releases calcium into blood and promotes blood coagulation in vitro

PubMed Central

Li, Jing; Cao, Wei; Lv, Xiao-xing; Jiang, Li; Li, Yue-jun; Li, Wang-zhou; Chen, Shao-zong; Li, Xue-yong

2013-01-01

Aim: To examine the changes in electrolyte concentrations after addition of zeolite-based hemostat QuikClot in blood and the effects of zeolite on blood coagulation in vitro. Methods: Fresh blood was taken from healthy adult volunteers and sheep, and the electrolyte concentrations in blood were measured using a blood electrolyte analyzer. Zeolite Saline Solution (ZSS) was prepared by addition of 2 g zeolite to 0.9% NaCl solution (4, 8, or 16 mL). The electrolytes in ZSS were measured using inductively coupled plasma atomic emission spectroscopy. The prothrombin time (PT) and activated partial thromboplastin time (APTT) of blood were measured using the test tube method. The activated clotting time (ACT) and clotting rate (CR) of blood were measured with Sonoclot Coagulation and Platelet Function Analyzer. Results: Addition of zeolite (50 and 100 mg) in 2 mL human blood significantly increased Ca2+ concentration, while Na+ and K+ concentrations were significantly decreased. Addition of zeolite (50 and 100 mg) in 0.9% NaCl solution (2 mL) caused similar changes in Ca2+ and Na+ concentrations. Si4+ (0.2434 g/L) and Al3+ (0.2575 g/L) were detected in ZSS (2 g/8 mL). Addition of ZSS in sheep blood shortened APTT in a concentration dependent manner, without changing PT. ZSS or aqueous solution of CaCl2 that contained Ca2+ concentration identical to that of ZSS significantly shortened ACT in human blood without significantly changing CR, and the effect of ZSS on ACT was not significantly different from that of CaCl2. Conclusion: Zeolite releases Ca2+ into blood, thus accelerating the intrinsic pathway of blood coagulation and shortening the clot formation time. PMID:23334236

Zeolite-based hemostat QuikClot releases calcium into blood and promotes blood coagulation in vitro.

PubMed

Li, Jing; Cao, Wei; Lv, Xiao-xing; Jiang, Li; Li, Yue-jun; Li, Wang-zhou; Chen, Shao-zong; Li, Xue-yong

2013-03-01

To examine the changes in electrolyte concentrations after addition of zeolite-based hemostat QuikClot in blood and the effects of zeolite on blood coagulation in vitro. Fresh blood was taken from healthy adult volunteers and sheep, and the electrolyte concentrations in blood were measured using a blood electrolyte analyzer. Zeolite Saline Solution (ZSS) was prepared by addition of 2 g zeolite to 0.9% NaCl solution (4, 8, or 16 mL). The electrolytes in ZSS were measured using inductively coupled plasma atomic emission spectroscopy. The prothrombin time (PT) and activated partial thromboplastin time (APTT) of blood were measured using the test tube method. The activated clotting time (ACT) and clotting rate (CR) of blood were measured with Sonoclot Coagulation and Platelet Function Analyzer. Addition of zeolite (50 and 100 mg) in 2 mL human blood significantly increased Ca(2+) concentration, while Na(+) and K(+) concentrations were significantly decreased. Addition of zeolite (50 and 100 mg) in 0.9% NaCl solution (2 mL) caused similar changes in Ca(2+) and Na(+) concentrations. Si(4+) (0.2434 g/L) and Al(3+) (0.2575 g/L) were detected in ZSS (2 g/8 mL). Addition of ZSS in sheep blood shortened APTT in a concentration dependent manner, without changing PT. ZSS or aqueous solution of CaCl2 that contained Ca(2+) concentration identical to that of ZSS significantly shortened ACT in human blood without significantly changing CR, and the effect of ZSS on ACT was not significantly different from that of CaCl2. Zeolite releases Ca(2+) into blood, thus accelerating the intrinsic pathway of blood coagulation and shortening the clot formation time.

A pilot study of addition of amifostine to melphalan, carboplatin, etoposide, and cyclophosphamide with autologous hematopoietic stem cell transplantation in pediatric solid tumors-A pediatric blood and marrow transplant consortium study.

PubMed

Ozkaynak, M Fevzi; Sahdev, Indira; Gross, Thomas G; Levine, John E; Cheerva, Alexandra C; Richards, Michael K; Rozans, Marta K; Shaw, Peter J; Kadota, Richard P

2008-03-01

Limited information is available regarding the use of amifostine in pediatric hematopoietic stem cell transplant (HSCT) patients. Melphalan, carboplatin, etoposide +/- cyclophosphamide is a commonly used preparatory regimen in pediatric solid tumor HSCT. Therefore, we decided to determine the feasibility of the addition of amifostine (750 mg/m b.i.d. x 4 d) to melphalan (200 mg/m), carboplatin (1200 mg/m), and etoposide (800 mg/m) (level 1) and escalating doses of cyclophosphamide (3000 mg/m and 3800 mg/m, levels 2 and 3, respectively) followed by autologous HSCT. Thirty-two patients with a variety of pediatric solid tumors were studied. Seventeen patients were accrued at level 1, 9 at level 2, and 6 at level 3. Major toxicities during the administration of the preparatory regimen were hypocalcemia, emesis, and hypotension. Hypocalcemia required aggressive calcium supplementation during the conditioning phase. No dose limiting toxicities were encountered at level 3. Amifostine at 750 mg/m b.i.d. for 4 days can be administered with a double alkylator regimen consisting of melphalan (200 mg/m), cyclophosphamide (up to 3800 mg/m), carboplatin (1200 mg/m), and etoposide (800 mg/m) with manageable toxicities.

Investigation of magnesium isotope fractionation during basalt differentiation: Implications for a chondritic composition of the terrestrial mantle

USGS Publications Warehouse

Teng, F.-Z.; Wadhwa, M.; Helz, R.T.

2007-01-01

To investigate whether magnesium isotopes are fractionated during basalt differentiation, we have performed high-precision Mg isotopic analyses by multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) on a set of well-characterized samples from Kilauea Iki lava lake, Hawaii, USA. Samples from the Kilauea Iki lava lake, produced by closed-system crystal-melt fractionation, range from olivine-rich cumulates to highly differentiated basalts with MgO content ranging from 2.37 to 26.87??wt.%. Our results demonstrate that although these basalts have diverse chemical compositions, mineralogies, crystallization temperatures and degrees of differentiation, their Mg isotopic compositions display no measurable variation within the limits of our external precision (average ??26Mg = - 0.36 ?? 0.10 and ??25Mg = - 0.20 ?? 0.07; uncertainties are 2SD). This indicates that Mg isotopic fractionation during crystal-melt fractionation at temperatures of ??? 1055????C is undetectable at the level of precision of the current investigation. Calculations based on our data suggest that at near-magmatic temperatures the maximum fractionation in the 26Mg/24Mg ratio between olivine and melt is 0.07???. Two additional oceanic basalts, two continental basalts (BCR-1 and BCR-2), and two primitive carbonaceous chondrites (Allende and Murchison) analyzed in this study have Mg isotopic compositions similar to the Kilauea Iki lava lake samples. In contrast to a recent report [U. Wiechert, A.N. Halliday, Non-chondritic magnesium and the origins of the inner terrestrial planets, Earth and Planetary Science Letters 256 (2007) 360-371], the results presented here suggest that the Bulk Silicate Earth has a chondritic Mg isotopic composition. ?? 2007.

Response surface methodology optimization for sorption of malachite green dye on sugarcane bagasse biochar and evaluating the residual dye for phyto and cytogenotoxicity.

PubMed

Vyavahare, Govind D; Gurav, Ranjit G; Jadhav, Pooja P; Patil, Ravishankar R; Aware, Chetan B; Jadhav, Jyoti P

2018-03-01

In the present study, sorption and detoxification of malachite green (MG) dye was executed using biochar resulting after pyrolysis of agro-industrial waste at 400, 600 and 800 °C. Maximum sorption of MG dye (3000 mg/L) was observed on the sugarcane bagasse biochar (SCB) prepared at 800 °C. The interactive effects of different factors like dye concentration, time, pH and temperature on sorption of MG dye were investigated using response surface methodology (RSM). Optimum MG dye concentration, contact time, temperature and pH predicted through Box-Behnken based RSM model were 3000 mg/L MG dye, 51.89 min, 60 °C and 7.5, respectively. ANOVA analysis displayed the non-significant lack of fit value (0.4566), whereas, the predicted correlation coefficient values (R 2 0.8494) were reasonably in agreement with the adjusted value (R 2 0.9363) demonstrating highly significant model for MG dye sorption. The applicability of this model was also checked through F- test (30.39) with lower probability (0.0001) value. Furthermore, the characterization of SCB was performed using fourier transform infra-red spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), Brunauer-Emmett-Teller surfaces (BET), total organic carbon (TOC) and atomic absorption spectroscopy (AAS). Phyto-toxicity and cytogenotoxicity studies showed successful removal of MG dye using SCB. In addition, the batch sorption studies for reutilization of SCB revealed that the SCB was effective in removal of MG for five repeated cycles. This technology would be effective for treating the toxic textile effluent released from the textile industries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mineral contents and proximate composition of Pistacia vera kernels.

PubMed

Harmankaya, Mustafa; Ozcan, Mehmet Musa; Al Juhaimi, Fahad

2014-07-01

The mineral contents of Pistacia vera kernels were determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The minimum and maximum values of K, P, Ca, Mg, and S elements ranged from 6,333 to 8,064 mg/kg, 3,630 to 5,228 mg/kg, 1,614 to 3,226 mg/kg, 1,716 to 2,402 mg/kg, and 1,417 to 1,825 mg/kg, respectively. In addition, the mean values of Fe, Zn, Cu, Mn, B, Mo, Cr and Ni elements were determined as 42.48, 20.52, 12.81, 7.48, 11.31, 0.106, 0.511 and 1.67 mg/kg, respectively. Ash levels of kernels were found between 2.28 % (Urfa) and 2.79 % (Halebi). In addition, crude oil and protein contents were determined between 48.8 % (Halebi) to 55.3 % (Siirt) and 23.33 % (Uzun) to 27.16 % (Halebi), respectively.

Iron, zinc and calcium dialyzability from extruded product based on whole grain amaranth (Amaranthus caudatus and Amaranthus cruentus) and amaranth/Zea mays blends.

PubMed

Galan, María Gimena; Drago, Silvina Rosa; Armada, Margarita; José, Rolando González

2013-06-01

Amaranth is a Native American grain appreciated for its high nutritional properties including high mineral content. The aim of this study was to evaluate the availability of Fe, Zn and Ca from extruded products made with two varieties of amaranth and their mixtures with maize at two levels of replacement. Mineral availability was estimated using dialyzability method. The contents of Fe (64.0-84.0 mg/kg), Ca (1977.5-2348.8 mg/kg) and Zn (30.0-32.1 mg/kg) were higher in amaranth than in maize products (6.2, 19.1, 9.7 mg/kg, respectively). Mineral availability was in the range of (2.0-3.6%), (3.3-11.1%) and (1.6-11.4%) for Fe, Ca and Zn, respectively. Extruded amaranth and amaranth/maize products provide higher amount of Fe and Ca than extruded maize. Extruded amaranth products and amaranth addition to maize could be an interesting way to increase nutritional value of extruded products.

Generation of reactive species in atmospheric pressure dielectric barrier discharge with liquid water

NASA Astrophysics Data System (ADS)

Zelong, ZHANG; Jie, SHEN; Cheng, CHENG; Zimu, XU; Weidong, XIA

2018-04-01

Atmospheric pressure helium/water dielectric barrier discharge (DBD) plasma is used to investigate the generation of reactive species in a gas-liquid interface and in a liquid. The emission intensity of the reactive species is measured by optical emission spectroscopy (OES) with different discharge powers at the gas-liquid interface. Spectrophotometry is used to analyze the reactive species induced by the plasma in the liquid. The concentration of OH radicals reaches 2.2 μm after 3 min of discharge treatment. In addition, the concentration of primary long-lived reactive species such as H2O2, {{{{NO}}}3}- and O3 are measured based on plasma treatment time. After 5 min of discharge treatment, the concentration of H2O2, {{{{NO}}}3}-, and O3 increased from 0 mg · L-1 to 96 mg · L-1, 19.5 mg · L-1, and 3.5 mg · L-1, respectively. The water treated by plasma still contained a considerable concentration of reactive species after 6 h of storage. The results will contribute to optimizing the DBD plasma system for biological decontamination.

An investigation of the properties of Mg-Zn-Al alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Z.; Couture, A.; Luo, A.

1998-06-05

During the past ten years, the use of magnesium castings in the automotive and electronics industries has been expanding at an impressive rate. Die casting is one of the most effective fabrication methods and has been extensively used to produce magnesium components, especially in the automotive industry. However, the number of available Mg-based alloys for die casting is very limited. Therefore, it is pressing to develop some new Mg die casting alloys with good creep resistance, acceptable castability and low cost. Mg-Zn-Al (ZA) is a promising alloy system which is able to meet the requirements. But up to now, onlymore » a small amount of research has been carried out on this system. The aim of the present work is to examine and evaluate the microstructural features, tensile properties and creep resistance in order to get a better overall understanding of alloys of this system and to identify the most promising compositions. The influence of small additions of Ca and Sr on the tensile and creep properties of ZA alloys was also investigated.« less

Assessment of N2O emission from a photobioreactor treating ammonia-rich swine wastewater digestate.

PubMed

Mezzari, Melissa P; da Silva, Márcio L B; Nicoloso, Rodrigo S; Ibelli, Adriana M G; Bortoli, Marcelo; Viancelli, Aline; Soares, Hugo M

2013-12-01

This study investigated the interactions between naturally occurring bacteria and the microalgae Chlorella vulgaris within a lab scale photobioreactor treating ammonia-rich swine wastewater digestate effluent. Nitrification and denitrification were assessed by targeting ammonia monoxygenases (amoA), nitrate (narG), nitrite (nirS), nitric oxide (norB) and nitrous oxide (nosZ) reductases genes. Oxygen produced from microalgae photosynthesis stimulated nitrification. Under limiting carbon availability (i.e., <1.44 for mg TOC/mg NO2-N and 1.72 for mg TOC/mg NO3-N), incomplete denitrification led to accumulation of NO2 and NO3. Significant N2O emission (up to 118 μg N2O-N) was linked to NO2 metabolism in Chlorella. The addition of acetate as external carbon source recovered heterotrophic denitrification activity suppressing N2O emission. Effluent methane concentrations trapped within photobioreactor was removed concomitantly with ammonia. Overall, closed photobioreactors can be built to effectively remove nitrogen and mitigate simultaneously greenhouse gases emissions that would occur otherwise in open microalgae-based wastewater treatment systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

MgZnO High Voltage Thin Film Transistors on Glass for Inverters in Building Integrated Photovoltaics

DOE PAGES

Hong, Wen-Chiang; Ku, Chieh-Jen; Li, Rui; ...

2016-10-10

Building integrated photovoltaics (BIPV) have attracted considerable interests because of its aesthetically attractive appearance and overall low cost. In BIPV, system integration on a glass substrate like windows is essential to cover a large area of a building with low cost. But, the conventional high voltage devices in inverters have to be built on the specially selected single crystal substrates, limiting its application for large area electronic systems, such as the BIPV. We demonstrate a Magnesium Zinc Oxide (MZO) based high voltage thin film transistor (HVTFT) built on a transparent glass substrate. We designed devices with unique ring-type structures andmore » use modulated Mg doping in the channel - gate dielectric interface, resulting in a blocking voltage of over 600 V. In addition to BIPV, the MZO HVTFT based inverter technology also creates new opportunities for emerging self-powered smart glass.« less

MgZnO High Voltage Thin Film Transistors on Glass for Inverters in Building Integrated Photovoltaics.

PubMed

Hong, Wen-Chiang; Ku, Chieh-Jen; Li, Rui; Abbaslou, Siamak; Reyes, Pavel; Wang, Szu-Ying; Li, Guangyuan; Lu, Ming; Sheng, Kuang; Lu, Yicheng

2016-10-10

Building integrated photovoltaics (BIPV) have attracted considerable interests because of its aesthetically attractive appearance and overall low cost. In BIPV, system integration on a glass substrate like windows is essential to cover a large area of a building with low cost. However, the conventional high voltage devices in inverters have to be built on the specially selected single crystal substrates, limiting its application for large area electronic systems, such as the BIPV. We demonstrate a Magnesium Zinc Oxide (MZO) based high voltage thin film transistor (HVTFT) built on a transparent glass substrate. The devices are designed with unique ring-type structures and use modulated Mg doping in the channel - gate dielectric interface, resulting in a blocking voltage of over 600 V. In addition to BIPV, the MZO HVTFT based inverter technology also creates new opportunities for emerging self-powered smart glass.

MgZnO High Voltage Thin Film Transistors on Glass for Inverters in Building Integrated Photovoltaics

PubMed Central

Hong, Wen-Chiang; Ku, Chieh-Jen; Li, Rui; Abbaslou, Siamak; Reyes, Pavel; Wang, Szu-Ying; Li, Guangyuan; Lu, Ming; Sheng, Kuang; Lu, Yicheng

2016-01-01

Building integrated photovoltaics (BIPV) have attracted considerable interests because of its aesthetically attractive appearance and overall low cost. In BIPV, system integration on a glass substrate like windows is essential to cover a large area of a building with low cost. However, the conventional high voltage devices in inverters have to be built on the specially selected single crystal substrates, limiting its application for large area electronic systems, such as the BIPV. We demonstrate a Magnesium Zinc Oxide (MZO) based high voltage thin film transistor (HVTFT) built on a transparent glass substrate. The devices are designed with unique ring-type structures and use modulated Mg doping in the channel - gate dielectric interface, resulting in a blocking voltage of over 600 V. In addition to BIPV, the MZO HVTFT based inverter technology also creates new opportunities for emerging self-powered smart glass. PMID:27721484

Effects of graphene oxide on the performance, microbial community dynamics and antibiotic resistance genes reduction during anaerobic digestion of swine manure.

PubMed

Zhang, Junya; Wang, Ziyue; Wang, Yawei; Zhong, Hui; Sui, Qianwen; Zhang, Changping; Wei, Yuansong

2017-12-01

The role of graphene oxide (GO) on anaerobic digestion (AD) of swine manure concerning the performance, microbial community and antibiotic resistance genes (ARGs) reduction was investigated. Results showed that methane production was reduced by 13.1%, 10.6%, 2.7% and 17.1% at GO concentration of 5mg/L, 50mg/L, 100mg/L and 500mg/L, respectively, but propionate degradation was enhanced along with GO addition. Both bacterial and archaeal community changed little after GO addition. AD could well reduce ARGs abundance, but it was deteriorated at the GO concentration of 50mg/L and 100mg/L and enhanced at 500mg/L, while no obvious changes at 5mg/L. Network and SEM analysis indicated that changes of each ARG was closely associated with variation of microbial community composition, environmental variables contributed most to the dynamics of ARGs indirectly, GO influenced the ARGs dynamics negatively and (heavy metal resistance genes (MRGs)) influenced the most directly. Copyright © 2017 Elsevier Ltd. All rights reserved.

Use of tailored loading-dose clopidogrel in patients undergoing selected percutaneous coronary intervention based on adenosine diphosphate-mediated platelet aggregation.

PubMed

Meng, Kang; Lü, Shu-Zheng; Zhu, Hua-Gang; Chen, Xin; Ge, Chang-Jiang; Song, Xian-Tao

2010-12-01

Adenosine phosphate-mediated platelet aggregation is a prognostic factor for major adverse cardiac events in patients who have undergone selective percutaneous coronary interventions. This study aimed to assess whether an adjusted loading dose of clopidogrel could more effectively inhibit platelet aggregation in patients undergoing selected percutaneous coronary intervention. A total of 205 patients undergoing selected percutaneous coronary intervention were enrolled in this multicenter, prospective, randomized study. Patients receiving domestic clopidogrel (n = 104) served as the Talcom (Taijia) group; others (n = 101) received Plavix, the Plavix group. Patients received up to 3 additional 300-mg loading doses of clopidogrel to decrease the adenosine phosphate-mediated platelet aggregation index by more than 50% (the primary endpoint) compared with the baseline. The secondary endpoint was major adverse cardiovascular events at 12 months. Compared with the rational loading dosage, the tailored loading dosage better inhibited platelet aggregation based on a > 50% decrease in adenosine phosphate-mediated platelet aggregation (rational loading dosage vs. tailored loading dosage, 48% vs. 73%, P = 0.028). There was no significant difference in the eligible index between the Talcom and Plavix groups (47% vs. 49% at 300 mg; 62% vs. 59% at 600 mg; 74% vs. 72% at 900 mg; P > 0.05) based on a standard adenosine diphosphate-mediated platelet aggregation decrease of > 50%. After 12 months of follow-up, there were no significant differences in major adverse cardiac events (2.5% vs. 2.9%, P = 5.43). No acute or subacute stent thrombosis events occurred. An adjusted loading dose of clopidogrel could have significant effects on antiplatelet aggregation compared with a rational dose, decreasing 1-year major adverse cardiac events in patients undergoing percutaneous coronary interventions based on adenosine phosphate-mediated platelet aggregation with no increase in bleeding.

The effects of deoxynivalenol-contaminated corn dried distillers grains with solubles in nursery pig diets and potential for mitigation by commercially available feed additives.

PubMed

Frobose, H L; Fruge, E D; Tokach, M D; Hansen, E L; DeRouchey, J M; Dritz, S S; Goodband, R D; Nelssen, J L

2015-03-01

Four experiments were conducted to investigate the effects of deoxynivalenol (DON) from naturally contaminated dried distillers grains with solubles (DDGS) and the efficacy of feed additives in nursery pig diets. In Exp. 1, 180 pigs (10.3 ± 0.2 kg BW) were fed 1 of 5 diets for 21 d. Diets were 1) Positive Control (PC; < 0.5 mg/kg DON), 2) Negative Control (NC; 4 mg/kg DON), 3) NC + 0.10% Biofix (Biomin Inc., Herzogenburg, Austria), 4) NC + 0.15% Cel-can (VAST Inc., Mason City, IA) and 0.50% bentonite clay, and 5) NC + 0.25% Defusion Plus (Cargill Animal Nutrition, Minneapolis, MN). Pigs fed the NC diet had poorer ( < 0.01) ADG than those fed the PC. Pigs fed Defusion Plus had improved ( < 0.03) ADG over those fed NC, whereas pigs fed Biofix or Cel-can with bentonite clay had reduced ADG ( < 0.01) compared with those fed PC. In Exp. 2, 340 pigs (11.7 ± 0.1 kg BW) were fed 1 of 8 diets for 21 d. Diets were 1) PC (< 0.5 mg/kg DON), 2) Low NC (1.5 mg/kg DON), 3) Low NC + 0.15% Biofix, 4) Low NC + 0.30% Biofix, 5) High NC (3.0 mg/kg DON), 6) High NC + 0.30% Biofix, 7) High NC + 0.45% Biofix, and 8) Diet 7 with 5% added water. Increasing the DON level reduced (linear; < 0.05) ADG, ADFI, and pig BW, and Biofix did not improve performance. In Exp. 3, 1,008 pigs (12.5 ± 0.3 kg BW) were fed 6 treatments for 24 d. Diets were 1) PC ( < 0.5 mg/kg DON), 2) NC (3 mg/kg DON), 3) NC + 0.25% Defusion, 4) NC + 0.50% Defusion, 5) Diet 3 with supplemental nutrients, and 6) Diet 5, pelleted. Pigs fed the NC had decreased ( < 0.01) ADG and ADFI, but adding Defusion improved (linear; < 0.04) ADG and ADFI over pigs fed NC. Pelleting improved ( < 0.01) both ADG and G:F, resulting in ADG above PC pigs. In Exp. 4, 980 pigs (12.0 ± 0.3 kg BW) were fed 1 of 7 diets in a 28-d trial in a 2 × 3 + 1 factorial arrangement. The 7 treatments were based on 3 diets fed in meal or pellet form: 1) PC (< 0.5 mg/kg DON), 2) NC (3 mg/kg DON), and 3) NC + 0.25% Defusion. Treatment 7 was Diet 3 with supplemental nutrients in pellet form. No interactions were observed between pelleting and Defusion. Pigs fed the NC had decreased ( < 0.01) ADG and ADFI, and pelleting improved ( < 0.01) ADG to PC levels, driven by improved ( < 0.01) G:F. Adding nutrients or Defusion had no effect. Overall, these studies show that Defusion and pelleting can help overcome some of the negative effects of DON, whereas other feed additives and additional nutrients do not.

Efficacy and safety of combination therapy: repaglinide plus metformin versus nateglinide plus metformin.

PubMed

Raskin, Philip; Klaff, Leslie; McGill, Janet; South, Stephen A; Hollander, Priscilla; Khutoryansky, Naum; Hale, Paula M

2003-07-01

An open-label, parallel-group, randomized, multicenter trial was conducted to compare efficacy and safety of repaglinide versus nateglinide, when used in a combination regimen with metformin for treatment of type 2 diabetes. Enrolled patients (n = 192) had HbA(1c) >7% and < or =12% during previous treatment with a sulfonylurea, metformin, or low-dose Glucovance (glyburide < or =2.5 mg, metformin < or =500 mg). After a 4-week metformin run-in therapy period (doses escalated to 1,000 mg b.i.d.), patients were randomized to addition of repaglinide (n = 96) (1 mg/meal, maximum 4 mg/meal) or nateglinide (n = 96) (120 mg/meal, reduced to 60 mg if needed) to the regimen for 16 weeks. Glucose, insulin, and glucagon were assessed after a liquid test meal at baseline and week 16. Final HbA(1c) values were lower for repaglinide/metformin treatment than for nateglinide/metformin (7.1 vs. 7.5%). Repaglinide/metformin therapy showed significantly greater mean reductions of HbA(1c) (-1.28 vs. -0.67%; P < 0.001) and of fasting plasma glucose (FPG) (-39 vs. -21 mg/dl; P = 0.002). Self-monitoring of blood glucose profiles were significantly lower for repaglinide/metformin before breakfast, before lunch, and at 2:00 A.M. Changes in the area under the curve of postprandial glucose, insulin, or glucagon peaks after a test meal were not significantly different for the two treatment groups during this study. Median final doses were 5.0 mg/day for repaglinide and 360 mg/day for nateglinide. Safety assessments were comparable for the two regimens. The addition of repaglinide to metformin therapy resulted in reductions of HbA(1c) and FPG values that were significantly greater than the reductions observed for addition of nateglinide.

Effects of Alloying Elements on Room and High Temperature Tensile Properties of Al-Si Cu-Mg Base Alloys =

NASA Astrophysics Data System (ADS)

Alyaldin, Loay

In recent years, aluminum and aluminum alloys have been widely used in automotive and aerospace industries. Among the most commonly used cast aluminum alloys are those belonging to the Al-Si system. Due to their mechanical properties, light weight, excellent castability and corrosion resistance, these alloys are primarily used in engineering and in automotive applications. The more aluminum is used in the production of a vehicle, the less the weight of the vehicle, and the less fuel it consumes, thereby reducing the amount of harmful emissions into the atmosphere. The principal alloying elements in Al-Si alloys, in addition to silicon, are magnesium and copper which, through the formation of Al2Cu and Mg2Si precipitates, improve the alloy strength via precipitation hardening following heat treatment. However, most Al-Si alloys are not suitable for high temperature applications because their tensile and fatigue strengths are not as high as desired in the temperature range 230-350°C, which are the temperatures that are often attained in automotive engine components under actual service conditions. The main challenge lies in the fact that the strength of heat-treatable cast aluminum alloys decreases at temperatures above 200°C. The strength of alloys under high temperature conditions is improved by obtaining a microstructure containing thermally stable and coarsening-resistant intermetallics, which may be achieved with the addition of Ni. Zr and Sc. Nickel leads to the formation of nickel aluminide Al3Ni and Al 9FeNi in the presence of iron, while zirconium forms Al3Zr. These intermetallics improve the high temperature strength of Al-Si alloys. Some interesting improvements have been achieved by modifying the composition of the base alloy with additions of Mn, resulting in an increase in strength and ductility at both room and high temperatures. Al-Si-Cu-Mg alloys such as the 354 (Al-9wt%Si-1.8wt%Cu-0.5wt%Mg) alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength values at both low and high temperatures. Additions of Zr, Ni, Mn and Sc would be expected to maintain the performance of these alloys at still higher temperatures. Six alloys were prepared using 0.2 wt% Ti grain-refined 354 alloy, comprising alloy R (354 + 0.25wt% Zr) considered as the base or reference alloy, and five others, viz., alloys S, T, U, V, and Z containing various amounts of Ni, Mn, Sc and Zr, added individually or in combination. For comparison purposes, another alloy L was prepared from 398 (Al-16%Si) alloy, reported to give excellent high temperature properties, to which the same levels of Zr and Sc additions were made, as in alloy Z. Tensile test bars were prepared from the different 354 alloys using an ASTM B-108 permanent mold. The test bars were solution heat treated using a one-step or a multi-step solution heat treatment, followed by quenching in warm water, and then artificial aging employing different aging treatments (T5, T6, T62 and T7). The one-step (or SHT 1) solution treatment consisted of 5 h 495 °C) and the multi-step (or SHT 2) solution treatment comprised 5 h 495°C + 2 h 515°C + 2 h 530°C. Thermal analysis of the various 354 alloy melts was carried out to determine the sequence of reactions and phases formed during solidification under close-to-equilibrium cooling conditions. The main reactions observed comprised formation of the alpha-Al dendritic network at 598°C followed by precipitation of the Al-Si eutectic and post-eutectic beta-Al5FeSi phase at 560°C; Mg2Si phase and transformation of the beta-phase into pi-Al8Mg 3FeSi6 phase at 540°C and 525°C; and lastly, precipitation of Al2Cu and Q-Al5Mg8Cu2Si 6 almost simultaneously at 498°C and 488°C. Larger sizes of AlFeNi and AlCuNi phase particles were observed in T alloy with its higher Ni content of 4 wt%, when compared to those seen in S alloy at 2% Ni content. Mn addition in Alloy U helps in reducing the detrimental effect of the beta-iron phase by replacing it with the less-detrimental Chinese script alpha-Al 15(Fe,Mn)3Si2 phase and sludge particles.

Media calcification, low erythrocyte magnesium, altered plasma magnesium, and calcium homeostasis following grafting of the thoracic aorta to the infrarenal aorta in the rat--differential preventive effects of long-term oral magnesium supplementation alone and in combination with alkali.

PubMed

Schwille, P O; Schmiedl, A; Schwille, R; Brunner, P; Kissler, H; Cesnjevar, R; Gepp, H

2003-03-01

Calcifications in arterial media are clinically well documented, but the role played by magnesium in pathophysiology and therapy is uncertain. To clarify this, an animal model in which the juxtacardial aorta was grafted to the infrarenal aorta, and the subsequent calcifications in the media of the graft and their response to oral supplementation with three magnesium-containing and alkalinizing preparations was investigated. Groups of highly inbred rats were formed as follows: sham-operation (Sham, n = 12), aorta transplantation (ATx, n = 12), ATx + magnesium citrate (MgC, n = 12), ATx + MgC + potassium citrate (MgCPC, n = 12), ATx + MgC + MgCPC (MgCPCSB, n = 12). At 84 (+/-2) days after ATx with or without treatment the following observations were made: (1) weight gain and general status were normal; (2) ATx rats developed massive media calcification, mineral accumulation in the graft, decreased erythrocyte magnesium and plasma parathyroid hormone, and increased plasma ionized magnesium and calcium, and uric acid; (3) Mg-treated rats developed variable degrees of metabolic alkalosis, but only MgCPCSB supplementation prevented calcifications. Additional findings after ATx alone were: imbalance in endothelin and nitric oxide production, the mineral deposited in media was poorly crystallized calcium phosphate, calcium exchange between plasma and graft, and bone resorption were unchanged. The superior anti-calcification effect of MgCPCSB was characterized by complete restoration of normal extracellular mineral homeostasis and uric acid, but sub-optimal normalization of erythrocyte magnesium. It was concluded that in the rat: (1) ATx causes loss of cellular magnesium, excess of extracellular magnesium and calcium in the presence of apparently unchanged bone resorption, and increased uricemia; (2) ATx facilitates enhanced influx of calcium into vascular tissue, leading to calcium phosphate deposition in the media; (3) ATx-induced calcification is prevented by dietary supplementation with a combination of magnesium, alkali citrate and bases. Although the described circulatory model of media calcification in the rat requires further investigation, the data allow ascribing a fundamental role to magnesium and acid-base metabolism.

Effect of stoichiometry and Cu-substitution on the phase structure and hydrogen storage properties of Ml-Mg-Ni-based alloys

NASA Astrophysics Data System (ADS)

Li, Yuan; Tao, Yang; Huo, Quan

2015-01-01

To improve the electrochemical properties of rare-earth-Mg-Ni-based hydrogen storage alloys, the effects of stoichiometry and Cu-substitution on the phase structure and thermodynamic properties of the alloys were studied. Nonsubstituted Ml0.80Mg0.20(Ni2.90Co0.50-Mn0.30Al0.30) x ( x = 0.68, 0.70, 0.72, 0.74, 0.76) alloys and Cu-substituted Ml0.80Mg0.20(Ni2.90Co0.50- y Cu y Mn0.30Al0.30)0.70 ( y = 0, 0.10, 0.30, 0.50) alloys were prepared by induction melting. Phase structure analysis shows that the nonsubstituted alloys consist of a LaNi5 phase, a LaNi3 phase, and a minor La2Ni7 phase; in addition, in the case of Cu-substitution, the Nd2Ni7 phase appears and the LaNi3 phase vanishes. Thermodynamic tests show that the enthalpy change in the dehydriding process decreases, indicating that hydride stability decreases with increasing stoichiometry and increasing Cu content. The maximum discharge capacity, kinetic properties, and cycling stability of the alloy electrodes all increase and then decrease with increasing stoichiometry or increasing Cu content. Furthermore, Cu substitution for Co ameliorates the discharge capacity, kinetics, and cycling stability of the alloy electrodes.

Further evaluation in field tests of the activity of three anthelmintics (fenbendazole, oxibendazole, and pyrantel pamoate) against the ascarid Parascaris equorum in horse foals on eight farms in Central Kentucky (2009-2010).

PubMed

Lyons, Eugene T; Tolliver, Sharon C; Kuzmina, Tetiana A; Collins, Sandra S

2011-10-01

The activity of three anthelmintics (fenbendazole-FBZ; oxibendazole-OBZ; and pyrantel pamoate-PRT) was ascertained against the ascarid Parascaris equorum in horse foals on eight farms in Central Kentucky (2009-2010) in field tests. A total of 316 foals were treated, and 168 (53.2%) were passing ascarid eggs on the day of treatment. Evaluation of drug efficacy was determined qualitatively by comparing the number of foals passing ascarid eggs in their feces before and after treatment. The main purpose was to obtain data on current activity of these compounds against ascarids. Additionally, the objective was to compare these findings with those from earlier data on the efficacy of these three compounds on nematodes in foals in this geographical area. Efficacies (average) for the foals ranged for FBZ (10 mg/kg) from 50% to 100% (80%), for OBZ (10 mg/kg) from 75% to 100% (97%), and for PRT at 1× (6.6 mg base/kg) from 0% to 71% (2%) and at 2× (13.2 mg base/kg) 0% to 0% (0%). Although the efficacy varied among the drugs, combined data for all farms indicated a significant reduction of ascarid infections for FBZ (p < 0.0001) and OBZ (p < 0.0001) but not for PRT (p = 0.0953).

Role of parenteral testosterone in hypospadias: A study from a teaching hospital in India

PubMed Central

Ahmad, Reyaz; Chana, Rajendra Singh; Ali, Syed Manazir; Khan, Shehtaj

2011-01-01

Objectives: To evaluate the effect of parenteral testosterone on penile length, preputial skin and side effects in patients with hypospadias. Materials and Methods: 23 patients with hypospadias were included in this study. An oily solution, each ml of which contained testosterone propionate 25 mg, and testosterone enanthate 110 mg, equivalent to 100 mg of testosterone was given deep intramuscularly 4, 3 and 2 weeks before reconstructive surgery at the dose of 2 mg/kg body weight. Increase in penile length, transverse preputial diameter, and diameter at the base of penis were noted. Basal testosterone levels were obtained before the institution of therapy and on the day of operation. In addition, side effect such as development of pubic hair and delay in bone age was noted. Results: Following parenteral testosterone administration, the mean increase in penile length, transverse preputial diameter and diameter at the base of penis was 1.35±0.40 cm (P<0.001), 1.40±0.47 cm (P<0.001), and 0.72±0.47 cm (P<0.001), respectively. Serum testosterone level after injection was well within normal range for that age. Minimal side effects were noted in form of development of fine pubic hair. Conclusion: We conclude that parenteral testosterone can be safely used to improve the surgical outcome of hypospadias repair. PMID:21976926

High-resolution study of levels in the astrophysically important nucleus 26Mg and resulting updated level assignments

NASA Astrophysics Data System (ADS)

Adsley, P.; Brümmer, J. W.; Faestermann, T.; Fox, S. P.; Hammache, F.; Hertenberger, R.; Meyer, A.; Neveling, R.; Seiler, D.; de Séréville, N.; Wirth, H.-F.

2018-04-01

Background: The 22Ne(α ,n )25Mg reaction is an important source of neutrons for the s -process. Direct measurement of this reaction and the competing 22Ne(α ,γ )26Mg reaction are challenging due to the gaseous nature of both reactants, the low cross section and the experimental challenges of detecting neutrons and high-energy γ rays. Detailed knowledge of the resonance properties enables the rates to be constrained for s -process models. Purpose: Previous experimental studies have demonstrated a lack of agreement in both the number and excitation energy of levels in 26Mg. To try to resolve the disagreement between different experiments, proton and deuteron inelastic scattering from 26Mg have been used to identify excited states. Method: Proton and deuteron beams from the tandem accelerator at the Maier-Leibnitz Laboratorium at Garching, Munich, were incident upon enriched 26MgO targets. Scattered particles were momentum-analyzed in the Q3D magnetic spectrograph and detected at the focal plane. Results: Reassignments of states around Ex=10.8 -10.83 MeV in 26Mg suggested in previous works have been confirmed. In addition, new states in 26Mg have been observed, two below and two above the neutron threshold. Up to six additional states above the neutron threshold may have been observed compared to experimental studies of neutron reactions on 25Mg, but some or all of these states may be due to 24Mg contamination in the target. Finally, inconsistencies between measured resonance strengths and some previously accepted Jπ assignments of excited 26Mg states have been noted. Conclusion: There are still a large number of nuclear properties in 26Mg that have yet to be determined and levels that are, at present, not included in calculations of the reaction rates. In addition, some inconsistencies between existing nuclear data exist that must be resolved in order for the reaction rates to be properly calculated.

Atomistic simulations of deformation mechanisms in ultralight weight Mg-Li alloys

NASA Astrophysics Data System (ADS)

Karewar, Shivraj

Mg alloys have spurred a renewed academic and industrial interest because of their ultra-light-weight and high specific strength properties. Hexagonal close packed Mg has low deformability and a high plastic anisotropy between basal and non-basal slip systems at room temperature. Alloying with Li and other elements is believed to counter this deficiency by activating non-basal slip by reducing their nucleation stress. In this work I study how Li addition affects deformation mechanisms in Mg using atomistic simulations. In the first part, I create a reliable and transferable concentration dependent embedded atom method (CD-EAM) potential for my molecular dynamics study of deformation. This potential describes the Mg-Li phase diagram, which accurately describes the phase stability as a function of Li concentration and temperature. Also, it reproduces the heat of mixing, lattice parameters, and bulk moduli of the alloy as a function of Li concentration. Most importantly, our CD-EAM potential reproduces the variation of stacking fault energy for basal, prismatic, and pyramidal slip systems that in uences the deformation mechanisms as a function of Li concentration. This success of CD-EAM Mg-Li potential in reproducing different properties, as compared to literature data, shows its reliability and transferability. Next, I use this newly created potential to study the effect of Li addition on deformation mechanisms in Mg-Li nanocrystalline (NC) alloys. Mg-Li NC alloys show basal slip, pyramidal type-I slip, tension twinning, and two-compression twinning deformation modes. Li addition reduces the plastic anisotropy between basal and non-basal slip systems by modifying the energetics of Mg-Li alloys. This causes the solid solution softening. The inverse relationship between strength and ductility therefore suggests a concomitant increase in alloy ductility. A comparison of the NC results with single crystal deformation results helps to understand the qualitative and quantitative effect of Li addition in Mg on nucleation stress and fault energies of each deformation mode. The nucleation stress and fault energies of basal dislocations and compression twins in single crystal Mg-Li alloy increase while those for pyramidal dislocations and tension twinning decrease. This variation in respective values explains the reduction in plastic anisotropy and increase in ductility for Mg-Li alloys.

The impact of processing meat and fish products on phosphorus intake in chronic kidney disease patients.

PubMed

Lou-Arnal, Luis M; Caverni-Muñoz, Alberto; Arnaudas-Casanova, Laura; Vercet-Tormo, Antonio; Gimeno-Orna, José A; Sanz-París, Alejandro; Caramelo-Gutiérrez, Rocío; Alvarez-Lipe, Rafael; Sahdalá-Santana, Laura; Gracia-García, Olga; Luzón-Alonso, Marta

2013-11-13

The use of phosphate additives in meat and fish processing leads to a phosphorus overload that we cannot quantify through labelling or food composition tables. We analysed this increase by measuring phosphorus content in these products by spectrophotometry. We determined the phosphorus/protein ratio in fresh meat and fish products with varying degrees of processing by spectrophotometry (phosphorus) and the Kjeldahl method (proteins). We contrasted these results with those reflected in the food composition tables. The phosphorus/protein ratio was higher in processed meat products (15.83 mg/g) than in battered (11.04 mg/g) and frozen meat products (10.5mg/g), and was lower in fresh (8.41 mg/g) and refrigerated meat products (8.78 mg/g). Fresh white fish had a phosphorus/protein ratio of 8.58mg/g, while it increased by 22% (10.3mg/g) in frozen white fish and by 46% (12.54 mg/g) in battered fish. The information in the tables was poor and confusing, and no reference is made to the brands tested. Processing meat and fish products poses a serious obstacle to the reduction of phosphorus intake. The current regulatory framework does not assist us in the objective of reducing phosphorus additives, since it considers them safe for public consumption. Overcoming these barriers requires a coordinated effort to demonstrate that a high intake of these additives may be harmful to the general population and it should be more closely examined by regulators.

Synthesis of C4 and C8 Chemicals from Ethanol on MgO-Incorporated Faujasite Catalysts with Balanced Confinement Effects and Basicity.

PubMed

Zhang, Lu; Pham, Tu N; Faria, Jimmy; Santhanaraj, Daniel; Sooknoi, Tawan; Tan, Qiaohua; Zhao, Zheng; Resasco, Daniel E

2016-04-07

A new type of catalyst has been designed to adjust the basicity and level of molecular confinement of KNaX faujasites by controlled incorporation of Mg through ion exchange and precipitation of extraframework MgO clusters at varying loadings. The catalytic performance of these catalysts was compared in the conversion of C2 and C4 aldehydes to value-added products. The product distribution depends on both the level of acetaldehyde conversion and the fraction of magnesium as extraframework species. These species form rather uniform and highly dispersed nanostructures that resemble nanopetals. Specifically, the sample containing Mg only in the form of exchangeable Mg(2+) ions has much lower activity than those in which a significant fraction of Mg exists as extraframework MgO. Both the (C6+C8)/C4 and C8/C6 ratios increase with additional extraframework Mg at high acetaldehyde conversion levels. These differences in product distribution can be attributed to 1) higher basicity density on the samples with extraframework species, and 2) enhanced confinement inside the zeolite cages in the presence of these species. Additionally, the formation of linear or aromatic C8 aldehyde compounds depends on the position on the crotonaldehyde molecule from which abstraction of a proton occurs. In addition, catalysts with different confinement effects result in different C8 products. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of Zn Interlayer on Interfacial Microstructure and Mechanical Properties of TIG Lap-Welded Mg/Al Joints

NASA Astrophysics Data System (ADS)

Gao, Qiong; Wang, Kehong

2016-03-01

This study explored 6061 Al alloy and AZ31B Mg alloy joined by TIG lap welding with Zn foils of varying thicknesses, with the additional Zn element being imported into the fusion zone to alloy the weld seam. The microstructures and chemical composition in the fusion zone near the Mg substrate were examined by SEM and EDS, and tensile shear strength tests were conducted to investigate the mechanical properties of the Al/Mg joints, as well as the fracture surfaces, and phase compositions. The results revealed that the introduction of an appropriate amount of Zn transition layer improves the microstructure of Mg/Al joints and effectively reduces the formation of Mg-Al intermetallic compounds (IMCs). The most common IMCs in the fusion zone near the Mg substrate were Mg-Zn and Mg-Al-Zn IMCs. The type and distribution of IMCs generated in the weld zone differed according to Zn additions; Zn interlayer thickness of 0.4 mm improved the sample's mechanical properties considerably compared to thicknesses of less than 0.4 mm; however, any further increase in Zn interlayer thickness of above 0.4 mm caused mechanical properties to deteriorate.

Green Manure Addition to Soil Increases Grain Zinc Concentration in Bread Wheat

PubMed Central

Aghili, Forough; Gamper, Hannes A.; Eikenberg, Jost; Khoshgoftarmanesh, Amir H.; Afyuni, Majid; Schulin, Rainer; Jansa, Jan; Frossard, Emmanuel

2014-01-01

Zinc (Zn) deficiency is a major problem for many people living on wheat-based diets. Here, we explored whether addition of green manure of red clover and sunflower to a calcareous soil or inoculating a non-indigenous arbuscular mycorrhizal fungal (AMF) strain may increase grain Zn concentration in bread wheat. For this purpose we performed a multifactorial pot experiment, in which the effects of two green manures (red clover, sunflower), ZnSO4 application, soil γ-irradiation (elimination of naturally occurring AMF), and AMF inoculation were tested. Both green manures were labeled with 65Zn radiotracer to record the Zn recoveries in the aboveground plant biomass. Application of ZnSO4 fertilizer increased grain Zn concentration from 20 to 39 mg Zn kg−1 and sole addition of green manure of sunflower to soil raised grain Zn concentration to 31 mg Zn kg−1. Adding the two together to soil increased grain Zn concentration even further to 54 mg Zn kg−1. Mixing green manure of sunflower to soil mobilized additional 48 µg Zn (kg soil)−1 for transfer to the aboveground plant biomass, compared to the total of 132 µg Zn (kg soil)−1 taken up from plain soil when neither green manure nor ZnSO4 were applied. Green manure amendments to soil also raised the DTPA-extractable Zn in soil. Inoculating a non-indigenous AMF did not increase plant Zn uptake. The study thus showed that organic matter amendments to soil can contribute to a better utilization of naturally stocked soil micronutrients, and thereby reduce any need for major external inputs. PMID:24999738

Drospirenone/ethinyl estradiol 3 mg/20 μg (24/4 day regimen): hormonal contraceptive choices – use of a fourth-generation progestin

PubMed Central

Bachmann, Gloria; Kopacz, Sharon

2009-01-01

The combined oral contraceptive pill (COC) consisting of drospirenone 3 mg/ethinyl estradiol 20 μg (3 mg DRSP/20 μg EE-24/4) supplies 24 days of pills with hormones followed by 4 days of hormone-free pills. This regimen is called the 24/4 regimen. The progesterone component of this oral contraceptive pill (OCP), drospirenone (DRSP), is a fourth-generation progestin that has potent progestogenic, antimineralocorticoid, and antiandrogenic activity, which are unique characteristics compared with the other progestogens contained in most of the other OCPs currently marketed. This formulation, in addition to being an effective long-term OCP, has the additional medical benefit of providing a good parallel treatment for premenstrual dysphoric disorder and moderate acne. The effectiveness of 3 mg DRSP/20 μg EE-24/4, its tolerability and safety, and its additional non-contraceptive benefits are discussed. PMID:19936169

High dose of plasmid IL-15 inhibits immune responses in an influenza non-human primates immunogenicity model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yin Jiangmei; Dai Anlan; Laddy, Dominick J.

2009-10-10

Interleukin (IL)-15, is a cytokine that is important for the maintenance of long-lasting, high-avidity T cell response to invading pathogens and has, therefore, been used in vaccine and therapeutic platforms as an adjuvant. In addition to pure protein delivery, plasmids encoding the IL-15 gene have been utilized. However, it is critical to determine the appropriate dose to maximize the adjuvanting effects. We immunized rhesus macaques with different doses of IL-15 expressing plasmid in an influenza non-human primate immunogenicity model. We found that co-immunization of rhesus macaques with a Flu DNA-based vaccine and low doses of plasmid encoding macaque IL-15 enhancedmore » the production of IFN-gamma (0.5 mg) and the proliferation of CD4{sup +} and CD8{sup +} T cells, as well as T{sub CM} levels in proliferating CD8{sup +} T cells (0.25 mg). Whereas, high doses of IL-15 (4 mg) decrease the production of IFN-gamma and the proliferation of CD4{sup +} and CD8{sup +} T cells and T{sub CM} levels in the proliferating CD4{sup +} and CD8{sup +} T cells. In addition, the data of hemagglutination inhibition (HI) antibody titer suggest that although not significantly different, there appears to be a slight increase in antibodies at lower doses of IL-15. Importantly, however, the higher doses of IL-15 decrease the antibody levels significantly. This study demonstrates the importance of optimizing DNA-based cytokine adjuvants.« less

Biofunctional activity of tortillas and bars enhanced with nopal. Preliminary assessment of functional effect after intake on the oxidative status in healthy volunteers.

PubMed

Guevara-Arauza, Juan Carlos; Ornelas Paz, José de Jesús; Mendoza, Sergio Rosales; Guerra, Ruth Elena Soria; Paz Maldonado, Luz María Teresita; González, Diana Jaqueline Pimentel

2011-03-03

Prickly pear cactus stem (nopal) has been used in folk medicine and a raw material since ancient times. Stems have been proved to possess components with valuable biological activities: anti inflamatory, antioxidant, antiulcerogenic, hypoglycemic, and so forth. Nowadays, people consume foods not only to cover the nutritional requirements, they also demand for healty, natural and convenient foods that show biological activity. This study evaluated the bio-functional effects of consuming tortillas or bars (filled with prickly pear fruit jam) supplemented or not with nopal dietary fiber. The addition of nopal increased the fiber and polyphenols content in both tortillas (16.67%, 2.33 mg QE/L) and bars (13.79%, 1.99 mg QE/L). Furthermore the trolox equivalent antioxidant capacity (TEAC, 1.47 mmol/L), polyphenols (7.67 mg QE/L) and vitamin C (77.91 μmol/L) showed increased levels in volunteer's plasma after intake. Also lower levels of glucose (4.43 mmol/L), total cholesterol (4.27 mmol/L), LDL (1.96 mmol/L) and triglycerides (1.54 mmol/L) were observed in plasma after the supplementation scheme with nopal-based tortilla, while GSH:GSSG ratio in erythrocytes was higher. The results suggested that the intake of nopal-based tortillas with high content in fiber and antioxidant compounds can help to improve the overall oxidative status in healthy humans, which can reduce the risk of some chronic diseases. In addition, these products showed suitable physicochemical characteristics to be marketed.

Biofunctional activity of tortillas and bars enhanced with nopal. Preliminary assessment of functional effect after intake on the oxidative status in healthy volunteers

PubMed Central

2011-01-01

Background Prickly pear cactus stem (nopal) has been used in folk medicine and a raw material since ancient times. Stems have been proved to possess components with valuable biological activities: anti inflamatory, antioxidant, antiulcerogenic, hypoglycemic, and so forth. Nowadays, people consume foods not only to cover the nutritional requirements, they also demand for healty, natural and convenient foods that show biological activity. This study evaluated the bio-functional effects of consuming tortillas or bars (filled with prickly pear fruit jam) supplemented or not with nopal dietary fiber. Results The addition of nopal increased the fiber and polyphenols content in both tortillas (16.67%, 2.33 mg QE/L) and bars (13.79%, 1.99 mg QE/L). Furthermore the trolox equivalent antioxidant capacity (TEAC, 1.47 mmol/L), polyphenols (7.67 mg QE/L) and vitamin C (77.91 μmol/L) showed increased levels in volunteer's plasma after intake. Also lower levels of glucose (4.43 mmol/L), total cholesterol (4.27 mmol/L), LDL (1.96 mmol/L) and triglycerides (1.54 mmol/L) were observed in plasma after the supplementation scheme with nopal-based tortilla, while GSH:GSSG ratio in erythrocytes was higher. Conclusions The results suggested that the intake of nopal-based tortillas with high content in fiber and antioxidant compounds can help to improve the overall oxidative status in healthy humans, which can reduce the risk of some chronic diseases. In addition, these products showed suitable physicochemical characteristics to be marketed. PMID:21371324

Metal hydrides: an innovative and challenging conversion reaction anode for lithium-ion batteries

PubMed Central

Oumellal, Yassine; Bonnet, Jean-Pierre

2015-01-01

Summary The state of the art of conversion reactions of metal hydrides (MH) with lithium is presented and discussed in this review with regard to the use of these hydrides as anode materials for lithium-ion batteries. A focus on the gravimetric and volumetric storage capacities for different examples from binary, ternary and complex hydrides is presented, with a comparison between thermodynamic prediction and experimental results. MgH2 constitutes one of the most attractive metal hydrides with a reversible capacity of 1480 mA·h·g−1 at a suitable potential (0.5 V vs Li+/Li0) and the lowest electrode polarization (<0.2 V) for conversion materials. Conversion process reaction mechanisms with lithium are subsequently detailed for MgH2, TiH2, complex hydrides Mg2MHx and other Mg-based hydrides. The reversible conversion reaction mechanism of MgH2, which is lithium-controlled, can be extended to others hydrides as: MHx + xLi+ + xe− in equilibrium with M + xLiH. Other reaction paths—involving solid solutions, metastable distorted phases, and phases with low hydrogen content—were recently reported for TiH2 and Mg2FeH6, Mg2CoH5 and Mg2NiH4. The importance of fundamental aspects to overcome technological difficulties is discussed with a focus on conversion reaction limitations in the case of MgH2. The influence of MgH2 particle size, mechanical grinding, hydrogen sorption cycles, grinding with carbon, reactive milling under hydrogen, and metal and catalyst addition to the MgH2/carbon composite on kinetics improvement and reversibility is presented. Drastic technological improvement in order to the enhance conversion process efficiencies is needed for practical applications. The main goals are minimizing the impact of electrode volume variation during lithium extraction and overcoming the poor electronic conductivity of LiH. To use polymer binders to improve the cycle life of the hydride-based electrode and to synthesize nanoscale composite hydride can be helpful to address these drawbacks. The development of high-capacity hydride anodes should be inspired by the emergent nano-research prospects which share the knowledge of both hydrogen-storage and lithium-anode communities. PMID:26425434

Effect of different levels of copper and molybdenum supplements on serum lipid profiles and antioxidant status in cashmere goats.

PubMed

Zhang, Wei; Zhang, Yu; Zhang, Shi W; Song, Xian Z; Jia, Zhi H; Wang, Run L

2012-09-01

An experiment was conducted to investigate on the effects of different levels of copper (Cu: 0, 19, and 38 mg/kg) and molybdenum (Mo: 0 and 5 mg/kg) supplements and the interaction of these two factors on serum lipid profiles and antioxidant status in cashmere goats during the cashmere fiber growing period. Thirty-six Liaoning cashmere goats (approximately 1.5 years of age; 27.53±1.38 kg of body weight) were assigned to one of six treatments in a completely randomized design involving a 2×3 factorial arrangement. Goats were housed in individual pens and fed with Chinese wild rye- and alfalfa hay-based diet containing 4.72 mg Cu/kg, 0.16 mg Mo/kg, and 0.21 % S for 84 days. Blood samples were collected on day 84. The triglyceride concentration did not differ among treatments (P>0.05). Supplemental Cu, regardless of Mo level, decreased (P<0.05) the concentrations of serum total cholesterol and low density lipoprotein cholesterol, and increased (P<0.05) the concentration of serum high density lipoprotein cholesterol, but there were no differences (P>0.05) in these values between Cu-supplemented groups. Supplemental Cu increased (P<0.05) the activities of serum ceruloplasmin (Cp), Cu-zinc superoxide dismutase (SOD), and glutathione peroxidase (GSH-Px), and decreased (P<0.05) the malondialdehyde content. The serum GSH-Px activity was also increased (P<0.05) by Mo supplementation. There was a tendency of the interaction effects of Cu and Mo on the activities of Cp (P=0.094), SOD (P=0.057), and GSH-Px (P=0.062), and goats fed with 19 mg Cu/kg in the absence of Mo tended to show the highest serum SOD activity, while goats fed with 38 mg Cu/kg with 5 mg Mo/kg tended to show the highest values of serum Cp and GSH-Px. Addition of Cu, Mo, or their interaction had no influence (P>0.05) on the activities of serum glutamate oxaloacetate transaminase, glutamate pyruvate transaminase, and lactate dehydrogenase, and the concentrations of serum glucose and total protein. In conclusion, addition of 19 mg Cu/kg in the absence of Mo (the total dietary Cu level of 23.72 mg/kg) was recommended for altering the fat metabolism and obtaining the optimal antioxidant activity of cashmere goats, while 38 mg Cu/kg should be supplemented when 5 mg Mo/kg was added in the basal diet (the total dietary level of 42.72 mg Cu/kg, 5.16 mg Mo/kg, and 0.21 % S) during the cashmere growing period.

Synergistic, additive and antagonistic effects of fruit mixtures on total antioxidant capacities and bioactive compounds in tropical fruit juices.

PubMed

Pereira, Ana Carolina da Silva; Wurlitzer, Nedio Jair; Dionisio, Ana Paula; Lacerda Soares, Marcia Valéria; Rocha Bastos, Maria do Socorro; Elesbão Alves, Ricardo; Montenegro Brasil, Isabella

2015-06-01

The objective of this work was investigate the synergistic, additive and antagonistic effects of fruit mixtures on total antioxidant capacities and bioactive compounds in tropical fruit juices, and optimize its formulation by the response surface methodology based on the responses: total polyphenols (TP), total antioxidant capacity (TAC), ascorbic acid content and sensorial acceptance. Camu-camu, acerola and acai were the major factors that influenced the antioxidant potential of the juice; and the yellow mombin showed a positive effect on the acceptance of the tropical juice. It was observed an/antagonistic effect between acerola and camu-camu for the TAC response. The optimum formulation obtained was 20% acerola, 10% camu-camu, 10% yellow mombin, 10% cashew apple and 10% acai, which was responsible for a response of 155.46 mg.100 g(-1) of ascorbic acid, 103.01 mg of GAE.100 g-1 of TP, 10.27 µM Trolox g(-1) of TAC and approximately 6.1 of acceptance.

Diastereoselective Synthesis of (+/-)-1,2-Diphenyl-1,2-propanediol. A Discovery-Based Grignard Reaction Suitable for a Large Organic Lab Course

NASA Astrophysics Data System (ADS)

Ciaccio, James A.; Bravo, Roxana P.; Drahus, Antoinette L.; Biggins, John B.; Concepcion, Rosalyn V.; Cabrera, David

2001-04-01

We have developed an undergraduate organic laboratory experiment that probes the diastereoselectivity of the reaction between a Grignard reagent and a common, inexpensive a-chiral ketone. Students isolate a single diastereomer of (+/-)-1,2-diphenyl-1,2-propanediol by treatment of (+/-)-benzoin with MeMgI. Since the mp ranges of the two possible diol diastereomers differ by 10 °C, the reaction's diastereoselectivity can be established by mp determination alone, and it can be rationalized by the preferential addition of MeMgI to the least sterically hindered face of the carbonyl group in a rigid, five-membered cyclic intermediate (the "Cram chelate model"). This experiment is an interesting alternative to traditional Grignard experiments, is operationally straightforward and easily performed in large lab courses, and introduces students to p-facial discrimination by having them establish the stereochemical course of kinetically controlled nucleophilic addition to a carbonyl.

Ipilimumab for Previously Untreated Unresectable Malignant Melanoma: A Critique of the Evidence.

PubMed

Giannopoulou, Christina; Sideris, Eleftherios; Wade, Ros; Moe-Byrne, Thirimon; Eastwood, Alison; McKenna, Claire

2015-12-01

The National Institute for Health and Care Excellence (NICE) invited the manufacturer of ipilimumab (Bristol-Myers Squibb Pharmaceuticals Limited) to submit clinical and cost-effectiveness evidence for previously untreated advanced (unresectable or metastatic) melanoma as part of the Institute's Single Technology Appraisal process. The Centre for Reviews and Dissemination and Centre for Health Economics at the University of York were commissioned to act as the independent Evidence Review Group (ERG). This article presents a summary of the manufacturer's submission of ipilimumab, the ERG review and the resulting NICE guidance TA319, issued in July 2014. Ipilimumab at a recommended dose of 3 mg/kg monotherapy was previously granted marketing authorisation by the European Medicines Agency in adult patients who had received prior therapy and was recommended by NICE in guidance TA268. In October 2013, the EMA approved the extension of this indication to previously untreated advanced melanoma patients. NICE decisions are bound by the marketing authorisation; therefore, the decision problem faced by the NICE Appraisal Committee was whether ipilimumab at a recommended dose of 3 mg/kg monotherapy was effective and cost effective compared with first-line standard of care involving dacarbazine (DTIC) and vemurafenib (for BRAF V600 mutation-positive patients). The CA184-024 trial was the primary source of clinical evidence for ipilimumab. However, this was based on a dose of 10 mg/kg with concomitant DTIC. The results over a 5-year period indicated that ipilimumab 10 mg/kg plus DTIC demonstrated a significant increase in median overall survival (OS) of 2.1 months compared with DTIC plus placebo (11.2 vs. 9.1 months). The BRIM-3 trial, which was an open-label randomised controlled trial (RCT) in BRAF V600 mutation-positive patients, was the primary source of evidence for an indirect comparison with vemurafenib. The results showed that vemurafenib increased median OS by 3.6 months compared with DTIC (13.2 vs. 9.6 months). The economic evaluation compared the costs and outcomes of ipilimumab by assuming that the 3 mg/kg dosing regimen was clinically equivalent in efficacy to an ipilimumab 10 mg/kg dosing regimen plus DTIC and by using a treatment sequencing approach that incorporated second-line active therapy and third-line best supportive care (BSC). In the first appraisal meeting, the committee recommended ipilimumab only in the context of research as part of a clinical study. This was primarily based on the lack of robust evidence to support the assumption of clinical equivalence between dosages and the absence of evidence available to inform the sequential use of treatments. Following the consultation, the manufacturer submitted additional analyses and evidence to support the cost effectiveness of ipilimumab at first line. The manufacturer's response was based on concerns relating to uncertainty surrounding the relative efficacy of ipilimumab 3 mg/kg monotherapy compared with DTIC and vemurafenib, comparability of the patient populations at first and second line, and the effects of concomitant DTIC. These additional analyses indicated that the incremental cost-effectiveness ratio (ICER) was £ 47,900 per quality-adjusted life-year (QALY) gained for ipilimumab compared with DTIC and £ 28,600 per QALY gained for ipilimumab compared with vemurafenib. Following consideration of the additional evidence and the responses from a large number of consultees and commentators, the committee recommended ipilimumab as an option for adults with previously untreated advanced melanoma.

The Role of MgCl 2 as a Lewis Base in ROMgCl-MgCl 2 Electrolytes for Magnesium-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Baofei; Huang, Jinhua; He, Meinan

2016-02-04

A series of strong Lewis acid-free alkoxide/siloxide-based Mg electrolytes were deliberately developed with remarkable oxidative stability up to 3.5 V (vs. Mg/Mg2+). Despite the perception of ROMgCl (R=alkyl, silyl) as a strong base, ROMgCl acts like Lewis acid, whereas the role of MgCl2 in was unambiguously demonstrated as a Lewis base through the identification of the key intermediate using single crystal X-ray crystallography. This Lewis-acid-free strategy should provide a prototype system for further investigation of Mg-ion batteries.

Multi-scale Investigation on Microstructure, Mechanical Properties, and Deformation Mechanisms in Mg Alloys

NASA Astrophysics Data System (ADS)

Zhang, Dalong

Mg and its alloys are promising candidates for light-weight structural applications, e.g., aircraft, automobile, electronic, etc. However, the inherent hexagonal close packed crystal structure makes the deformation of Mg anisotropic, namely deformation only occurs predominantly by dislocation slip in the close-packed (0001) plane (i.e., basal plane), or by deformation twinning in {101¯2} planes. Both basal slip and twinning cause the crystal to re-orient. Consequently, polycrystalline Mg alloys that have undergone thermomechanical processing usually contain strong texture, i.e., preferred crystallographic orientation in grains. The texture in turn leads to anisotropic deformation in wrought Mg alloys. For example, in extruded Mg alloys, the compressive yield strength is usually much lower than the tensile yield strength (so-called yield asymmetry and strength differential). It is the anisotropy that hinders the broader application of Mg alloys. Recent modeling studies on Mg predict that certain alloying elements, particularly rare-earth elements (e.g., Y, Ce, Nd, Gd, etc.), could alter the active deformation modes and enhance homogeneous deformation and overall mechanical properties in Mg. Therefore, the objective of this dissertation research is to investigate experimentally the effects of alloying element Y in reducing the intrinsic and extrinsic anisotropy, modifying texture, and enhancing the overall strength and ductility for Mg. In addition, the research also uncovered some unexpected "side effects" of Y and these phenomena were studied and explained from a fundamental perspective. The methodology used in this work is described as follows. Ultrafine grained Mg 2.5 at.% Y alloy (UFG Mg-2.5Y) was prepared by powder metallurgy method, including gas atomization for producing Mg-2.5Y powder, degassing and hot isostatic pressing (HIP), and hot extrusion. Both the as-HIPed and the as-extruded materials were characterized by electron back-scattered diffraction (EBSD), transmission electron microscopy (TEM), and/or atom probe tomography (APT). It is noted that different configurations of stacking faults (all in basal plane, i.e., basal stacking faults, BSFs for short) were observed in the as-extruded Mg-2.5Y, whereas no BSFs were documented in the as-HIPed alloy. Feasible models to explain the formation of BSFs were proposed based on the activity of different dislocations. Tension and compression tests were carried out along the extrusion direction (ED) for UFG Mg-2.5Y. Unlike common Mg alloys exhibiting yield asymmetry, the UFG Mg-2.5Y exhibits yield "symmetry" and significantly reduced strength differential. Namely, the deformation is more isotropic. In addition to post-mortem TEM characterization for deformed UFG Mg-2.5Y, in-situ TEM was also performed, in an effort to understand the fundamental deformation mechanisms in UFG Mg-Y that lead to reduced anisotropy. In-situ TEM for single-crystal Mg-Y nano-pillars reveals that deformation twinning is replaced by dislocation slip in non-basal planes (i.e., prismatic planes), which diametrically differs from any other Mg alloys. However, it is noted that deformation twinning still occurs in the polycrystalline UFG Mg-2.5Y occasionally, and a new type of stacking faults (i.e., prismatic stacking faults, PSFs for short) may be present in the vicinity of twins. Feasible mechanisms explaining the formation of PSFs are proposed.

Addition of an organic amendment and/or residue mud to bauxite residue sand in order to improve its properties as a growth medium.

PubMed

Jones, B E H; Haynes, R J; Phillips, I R

2012-03-01

The effects of addition of carbonated residue mud (RMC) or seawater neutralized residue mud (RMS), at two rates, in the presence or absence of added green waste compost, on the chemical, physical and microbial properties of gypsum-treated bauxite residue sand were studied in a laboratory incubation study. The growth of two species commonly used in revegetation of residue sand (Lolium rigidum and Acacia saligna) in the treatments was then studied in a 18-week greenhouse study. Addition of green waste-based compost increased ammonium acetate-extractable (exchangeable) Mg, K and Na. Addition of residue mud at 5 and 10% w/w reduced exchangeable Ca but increased that of Mg and Na (and K for RMS). Concentrations of K, Na, Mg and level of EC in saturation paste extracts were increased by residue mud additions. Concentrations of cations in water extracts were considerably higher than those in saturation paste extracts but trends with treatment were broadly similar. Addition of both compost and residue mud caused a significant decrease in macroporosity with a concomitant increase in mesoporosity and microporosity, available water holding capacity and the quantity of water held at field capacity. Increasing rates of added residue mud reduced the percentage of sample present as discrete sand particles and increased that in aggregated form (particularly in the 1-2 and >10mm diameter ranges). Organic C content, C/N ratio, soluble organic C, microbial biomass C and basal respiration were increased by compost additions. Where compost was added, residue mud additions caused a substantial increase in microbial biomass and basal respiration. L. rigidum grew satisfactorily in all treatments although yields tended to be reduced by additions of mud (especially RMC) particularly in the absence of added compost. Growth of A. saligna was poor in sand alone and mud-amended sand and was greatly promoted by additions of compost. However, in the presence of compost, addition of carbonated mud had a marked depressive effect on both top and root growth. The significant positive effect of compost was attributed to substantial inputs of K and marked reductions in the Na/K ratio in soil solution while the depressive effect of RMC was attributed to its greater alkalinity and consequently higher concentrations of HCO(3)(-) in solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effects of Sn addition on the microstructure and tensile properties of AX55 alloys

NASA Astrophysics Data System (ADS)

Qiu, K. Q.; Huang, P.

2018-04-01

The microstructures and tensile properties at both room and elevated temperatures for both the as-cast and as-aged Mg-5Al-5Ca (AX55) alloy with 0–2 wt% Sn addition were studied. The results indicate that the α-Mg dendrite is gradually refined and the interdendritic Al2Ca and Mg2Ca intermetallics become more connected with Sn addition. The as-cast AX55-1Sn alloy shows optimal ultimate tensile strength (UTS) at testing temperature from 25 to 225 °C. After T61 and T62 heat treatment, the eutectic-lamellar microstructure of the as-cast alloys tends to be spheroidized and distributed uniformly along the grain boundaries. While the alloys with higher Sn content show higher density of granulated and needle-shaped Al2Ca phases precipitated into α-Mg matrix, which results in the increase of UTS, yield strength (YS), elongation and microhardness with Sn addition. The morphology of CaMgSn phase can be improved by T62 treatment, which makes as-aged AX55-2.0Sn alloy exhibit a smaller decrease rate of the UTS at temperature up to 225 °C. The heat resistance of different heat-resistant magnesium alloys were compared and discussed by using the decrease rate of the UTS.

CdCl2 Passivation of Polycrystalline CdMgTe and CdZnTe Absorbers for Tandem Photovoltaic Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Metzger, Wyatt K; Swanson, Drew; Reich, Carey

As single-junction silicon solar cells approach their theoretical limits, tandems provide the primary path to higher efficiencies. CdTe alloys can be tuned with magnesium (CdMgTe) or zinc (CdZnTe) for ideal tandem pairing with silicon. A II-VI/Si tandem holds the greatest promise for inexpensive, high-efficiency top cells that can be quickly deployed in the market using existing polycrystalline CdTe manufacturing lines combined with mature silicon production lines. Currently, all high efficiency polycrystalline CdTe cells require a chloride-based passivation process to passivate grain boundaries and bulk defects. This research examines the rich chemistry and physics that has historically limited performance when extendingmore » Cl treatments to polycrystalline 1.7-eV CdMgTe and CdZnTe absorbers. A combination of transmittance, quantum efficiency, photoluminescence, transmission electron microscopy, and energy-dispersive X-ray spectroscopy clearly reveals that during passivation, Mg segregates and out-diffuses, initially at the grain boundaries but eventually throughout the bulk. CdZnTe exhibits similar Zn segregation behavior; however, the onset and progression is localized to the back of the device. After passivation, CdMgTe and CdZnTe can render a layer that is reduced to predominantly CdTe electro-optical behavior. Contact instabilities caused by inter-diffusion between the layers create additional complications. The results outline critical issues and paths for these materials to be successfully implemented in Si-based tandems and other applications.« less

Effects of additional oxazepam in long-term users of oxazepam.

PubMed

Voshaar, Richard C Oude; Verkes, Robbert-Jan; van Luijtelaar, Gilles L J M; Edelbroek, Peter M; Zitman, Frans G

2005-02-01

Although additional dosages of benzodiazepines in long-term users of benzodiazepines are common, it is unknown whether these additional dosages resort any effect. The effects of an additional 20-mg dosage oxazepam were assessed in a double-blind, balanced-order, crossover randomized study comparing 16 long-term users of oxazepam (patients) with 18 benzodiazepine-naive controls (controls). The effects of 10 and 30 mg oxazepam were assessed at pretest and 2.5 hours after drug administration on: (a) saccadic eye movements as proxy for the sedative effect, (b) acoustic startle response (ASR) as proxy for the anxiolytic effects, (c) memory, (d) reaction time tasks, and (e) subjective measurements. Dose-related effects were found in patients on the peak velocity of saccadic eye movement and on response probability, respectively peak amplitude of the ASR. Comparison with controls, however, suggests that in patients the sedative effects might be mixed up with suppression of sedative withdrawal symptoms, whereas patients were as sensitive as benzodiazepine-naive controls for the effects of an additional dosage on the ASR. Neither 10 nor 30 mg oxazepam challenge affected the reaction time tasks in patients, whereas controls show a dose-related impairment. The memory impairing effects, however, did not differ significantly between patients and controls. In contrast to controls, patients could not discriminate between a 10- and 30-mg dosage as assessed by visual analogue scales and the STAI-DY-1, which might indicate a placebo effect in the 10-mg challenge in patients. We conclude that additional dosages of oxazepam still exert pronounced effects after daily use for more than 10 years.

Enhancing arabic bread quality and shelf life stability using bread improvers.

PubMed

Aleid, S M; Al-Hulaibi, A A; Ghoush, M Abu; Al-Shathri, A A

2015-08-01

Arabic breads is produced mainly from hard red winter wheat (HRWW) and have relatively little crumb, dense texture, form pocket and are often round with golden brown crust color. The objectives of this research were to investigate the effect of different bread improvers combinations addition in enhancing the quality parameters of Arabic bread. Therefore, the ability of Arabic bread for rolling, folding and overall quality were evaluated during the Arabic bread storage period for 2 days. It was found that there was significant effect of bread improvers combinations (Arabic gum "AG" * Mongglycerides "MG" *alpha-amylase) addition on the ability of Arabic bread for rolling and folding on the second day (P ≤ 0.1). The highest white Arabic bread quality was obtained significantly from addition of low AG, high of MG and high alpha-amylase combination and high AG, low of MG and high alpha-amylase combination. While, low of AG, high of MG and low alpha-amylase combination and high of AG, high of MG and low alpha-amylase combination significantly exhibited the highest overall quality for the Arabic bread made from whole flour.

Protective effect of ginger and zinc chloride mixture on the liver and kidney alterations induced by malathion toxicity.

PubMed

Baiomy, Ahmed A; Attia, Hossam F; Soliman, Mohamed M; Makrum, Omar

2015-03-01

This study was carried out on four groups of male Wistar rats, 10 rats per group. Group I got open access to food intake and water with normal balanced diet. Group II was administered 400 mg ginger per kg body weight (BW) and zinc chloride (ZnCl2) (300 mg/L) diluted in tap water for 4 months. Group III was administered malathion at a dose of 50 mg/kg BW/day in 0.2 mL corn oil via gavages for 4 months. This dose equal to 1/50 of the LD50. Group IV was given a mixture of 400 mg ginger per kg BW and ZnCl2 (300 mg/L) diluted in tap water in addition to 100 mg malathion/kg BW for 4 months. The liver showed histopathological changes include congestion, edema, and leucocytic infiltrations which were ameliorated by the addition of ginger and ZnCl2 mixture. The kidney showed cloudy swelling and hydropic degeneration of the renal tubules. These changes were ameliorated by the addition of ginger and ZnCl2 mixture. Ki67 immunoreactivity was localized in the cytoplasm and nuclear membrane. Its expression was estimated as the percentage of cells positively stained by the antibody in the different groups. In conclusion, malathion was toxic to the liver and kidney and must be avoided and protected by the addition of ginger and zinc mixture. © The Author(s) 2015.

Ultrasonic Vibration and Rheocasting for Refinement of Mg-Zn-Y Alloy Reinforced with LPSO Structure

NASA Astrophysics Data System (ADS)

Lü, Shulin; Yang, Xiong; Hao, Liangyan; Wu, Shusen; Fang, Xiaogang; Wang, Jing

2018-05-01

In this work, ultrasonic vibration (UV) and rheo-squeeze casting was first applied on the Mg alloy reinforced with long period stacking ordered (LPSO) structure. The semisolid slurry of Mg-Zn-Y alloy was prepared by UV and processed by rheo-squeeze casting in succession. The effects of UV, Zr addition and squeeze pressure on microstructure of semisolid Mg-Zn-Y alloy were studied. The results revealed that the synergic effect of UV and Zr addition generated a finer microstructure than either one alone when preparing the slurries. Rheo-squeeze casting could significantly refine the LPSO structure and α-Mg matrix in Mg96.9Zn1Y2Zr0.1 alloy without changing the phase compositions or the type of LPSO structure. When the squeeze pressure increased from 0 to 400 MPa, the block LPSO structure was completely eliminated and the average thickness of LPSO structure decreased from 9.8 to 4.3 μm. Under 400 MPa squeeze pressure, the tensile strength and elongation of the rheocast Mg96.9Zn1Y2Zr0.1 alloy reached the maximum values, which were 234 MPa and 17.6%, respectively, due to its fine α-Mg matrix (α1-Mg and α2-Mg grains) and LPSO structure.

Bulk-Type All-Solid-State Lithium-Ion Batteries: Remarkable Performances of a Carbon Nanofiber-Supported MgH2 Composite Electrode.

PubMed

Zeng, Liang; Ichikawa, Takayuki; Kawahito, Koji; Miyaoka, Hiroki; Kojima, Yoshitsugu

2017-01-25

Magnesium hydride, MgH 2 , a recently developed compound for lithium-ion batteries, is considered to be a promising conversion-type negative electrode material due to its high theoretical lithium storage capacity of over 2000 mA h g -1 , suitable working potential, and relatively small volume expansion. Nevertheless, it suffers from unsatisfactory cyclability, poor reversibility, and slow kinetics in conventional nonaqueous electrolyte systems, which greatly limit the practical application of MgH 2 . In this work, a vapor-grown carbon nanofiber was used to enhance the electrical conductivity of MgH 2 using LiBH 4 as the solid-state electrolyte. It shows that a reversible capacity of over 1200 mA h g -1 with an average voltage of 0.5 V (vs Li/Li + ) can be obtained after 50 cycles at a current density of 1000 mA g -1 . In addition, the capacity of MgH 2 retains over 1100 mA h g -1 at a high current density of 8000 mA g -1 , which indicates the possibility of using MgH 2 as a negative electrode material for high power and high capacity lithium-ion batteries in future practical applications. Moreover, the widely studied sulfide-based solid electrolyte was also used to assemble battery cells with MgH 2 electrode in the same system, and the electrochemical performance was as good as that using LiBH 4 electrolyte.

Analgesic Efficacy and Safety of Buprenorphine in Chinchillas (Chinchilla lanigera).

PubMed

Fox, Lana; Mans, Christoph

2018-05-01

Buprenorphine is routinely used in chinchillas at reported doses of 0.01 to 0.1 mg/kg IM or SC. However, these dose recommendations are based on anecdotal reports or extrapolation from studies in other species. Therefore, the purpose of this study was to evaluate the analgesic efficacy and safety of subcutaneously administered buprenorphine in chinchillas. Using a randomized, blind, controlled, complete crossover design, we evaluated buprenorphine at a single dose of 0.05, 0.1 or 0.2 mg/kg SC (experiment A) and 0.2 mg/kg SC (experiment B). Analgesic efficacy was determined by measuring limb withdrawal latencies in response to a thermal noxious stimulus (Hargreaves method) at 0, 3, 6, 12, and 24 h (experiment A) and at 0, 1, 2, 4, and 8 h (experiment B). In a third experiment, food intake and fecal output were monitored after repeated administration of buprenorphine (0.2 mg/kg SC every 6 h for 3 doses). Buprenorphine at 0.2 mg/kg SC, but not at 0.05 or 0.1 mg/kg SC, significantly increased limb withdrawal latencies for less than 4 h. Self-limiting reduction in food intake and fecal output occurred after administration at the 0.2-mg/kg dose in animals undergoing algesiometry. In chinchillas not undergoing algesiometry, the administration of 3 doses at 0.2 mg/kg SC every 6 h did not reduce food intake but significantly decreased fecal output for the first 24 h. Additional studies are needed to evaluate buprenorphine in different algesiometry models and to establish its pharmacokinetic profile in chinchillas.

Determination of the overall migration from silicone baking moulds into simulants and food using 1H-NMR techniques.

PubMed

Helling, Ruediger; Mieth, Anja; Altmann, Stefan; Simat, Thomas Joachim

2009-03-01

Different silicone baking moulds (37 samples) were characterized with respect to potential migrating substances using 1H-NMR, RP-HPLC-UV/ELSD and GC techniques. In all cases cyclic organosiloxane oligomers with the formula [Si(CH3)2-O]n were identified (n = 6 ... 50). Additionally, linear, partly hydroxyl-terminated organosiloxanes HO-[Si(CH3)2-O]n-H (n = 7 ... 20) were found in 13 samples. No substances other than siloxanes could be detected, meaning the migrants mainly consist of organopolysiloxanes. Based on this knowledge, a 1H-NMR quantification method for siloxanes was established for the analysis of both simulants and foodstuffs. Validation of the 1H-NMR method gave suitable performance characteristics: limit of detection 8.7 mg kg(-1) oil, coefficient of variation 7.8% (at a level of 1.0 mg kg(-1) food). Migration studies were carried out with simulants (olive oil, isooctane, ethanol (95%), Tenax) as well as preparation of different cakes. From the 1st to 10th experiment, siloxane migration into cakes only slightly decreased, with a significant dependence on fat content. Migration never exceeded a level of 21 mg kg(-1) (3 mg dm(-2)) and was, therefore, well below the overall migration limit of 60 mg kg(-1) (10 mg dm(-2)). However, migration behaviour into simulants differed completely from these results.

Silver and zinc oxide nanostructures loaded on activated carbon as new adsorbents for removal of methylene green: a comparative study.

PubMed

Ghaedi, M; Karimi, H; Yousefi, F

2014-09-01

In this study, the removal of methylene green (MG) from aqueous solution based on two new adsorbents including silver nanoparticles and zinc oxide nanorods loaded on activated carbon (Ag-NP-AC and ZnO-NR-AC, respectively) has been carried out. The dependency of removal process to variables such as contact time, pH, amount of adsorbents, and initial MG concentration were examined and optimized. It was found that the maximum MG removal percentage was achieved at pH = 7.0 following stirring at 400 r min(-1) for 7 and 6 min for Ag-NP-AC and ZnO-NR-AC, respectively. Equilibrium data were well fitted with the Langmuir model having maximum adsorption capacity of 166.7 and 200 mg g(-1) for Ag-NP-AC and ZnO-NR-AC, respectively. Thermodynamic parameters of MG adsorption on Ag-NP-AC such as enthalpy and entropy changes, activation energy, sticking probability, and Gibbs free energy changes show the spontaneous and endothermic nature of the removal process. Among different conventional kinetic models, the pseudo second-order kinetics in addition to particle diffusion mechanism is the best and efficient model for the prediction and explanation of experimental data of MG adsorption onto both adsorbents. © The Author(s) 2014.

Investigations on the effect of grain size on hot tearing susceptibility of MgZn1Y2 alloy

NASA Astrophysics Data System (ADS)

Zhou, Z. J.; Liu, Z.; Wang, Y.; Mao, P. L.; Tang, W. R.; Zhou, Y.

2018-05-01

Effect of grain size on hot tearing susceptibility of MgZn1Y2 alloy was explored in the present paper. Based on the microstructure observation and phase constitution analysis results by the method of OM, SEM, EBSD and XRD, it was found that the addition of 0.2 wt% C2Cl6 or 0.5 wt% Zr could reduced the grain size significantly. The addition of Zr had the better effect than that of 0.2 wt% C2Cl6. The average grain size reduced from 55.48 μm to 20.64 μm, and the average grain shape aspect ratio reduced from 1.859 to 1.49 with the addition of Zr. Although the addition of 0.2 wt% C2Cl6 refined grain, it also reduced the amount of LPSO phase. It was also found that the dendrite coherent temperature (Tcoh) decreased with decreasing of the grain size of the alloy, while the dendrite coherent solid fraction ({{{{f}}}{{s}}}{{coh}}) increased with decreasing of the alloy. The modified Clyne-Davies model was used to predict the hot cracking susceptibility of the alloy. The predicted results indicated that the hot tearing susceptibility decreased with grain refinement. With addition of 0.2 wt% Zr, the predicted hot tearing sensitivity value was reduced by about 2.5 times than that of the alloy without the addition of Zr.

Effects of chloride additives on the mechanical stability and environmental durability of porous MgF2 thin films

NASA Astrophysics Data System (ADS)

Schütz, F.; Scheurell, K.; Scholz, G.; Kemnitz, E.

2016-09-01

Porous antireflective thin films, prepared of nanoscopic MgF2 sols, exhibit a low refraction index and are useful for various optical applications. Due to their porosity, film stability and durability suffer from mechanical abrasion and water solubility, respectively. Hence, we present approaches of improved mechanical stability of MgF2 layers induced by chloride addition. Antireflective (AR) films were produced by dip-coating followed by thermal treatment. Afterwards, film stability and environmental durability was strained by crockmeter and water stability tests, respectively. In comparison to films prepared from chloride-free MgF2 sols, chloride mingled sols form coatings with increased mechanical stability and a lower solubility.

Diabetes Prevention and Treatment Programs for Western PA FY04 and FY05

DTIC Science & Technology

2009-05-01

LDL > 130 mg/dl. First line Rx is HMG CoA reductase inhibitor montotherapy. Initial treatment and dose: Atorvastatin (dose range 10-80 mg) with...necessary. Attempts to decrease higher doses if goals are reached may also be necessary.) High atorvastatin or simvastatin dose (80 mg) may be needed...100mg/dl, add or switch to atorvastatin or simvastatin 10 mg with evening meal. If LDL-C still remains >100 mg/dl after above addition, up-titrate

Effect of amlodipine, efonidipine, and trichlormethiazide on home blood pressure and upper-normal microalbuminuria assessed by casual spot urine test in essential hypertensive patients.

PubMed

Hosaka, Miki; Inoue, Ryusuke; Satoh, Michihiro; Watabe, Daisuke; Hanazawa, Tomohiro; Ohkubo, Takayoshi; Asayama, Kei; Obara, Taku; Imai, Yutaka

2018-01-01

The aim of this study was to assess the effects of irbesartan alone and combined with amlodipine, efonidipine, or trichlormethiazide on blood pressure (BP) and urinary albumin (UA) excretion in hypertensive patients with microalbuminuria (30≤UA/creatinine (Cr) ratio [UACR] <300 mg/g Cr) and upper-normal microalbuminuria (10≤UACR<30 mg/g Cr). This randomized controlled trial enrolled 175 newly diagnosed and untreated hypertensive patients (home systolic blood pressure [SBP]≥135 mmHg; 10≤UACR<300 mg/g Cr of casual spot urine at the first visit to clinic). All patients were treated with irbesartan (week 0). Patients who failed to achieve home SBP ≤125 mmHg on 8-week irbesartan monotherapy (nonresponders, n = 115) were randomized into three additional drug treatment groups: trichlormethiazide (n = 42), efonidipine (n = 39), or amlodipine (n = 34). Irbesartan monotherapy decreased home SBP and first morning urine samples (morning UACR) for 8 weeks (p < 0.0001). At 8 weeks after randomization, all three additional drugs decreased home SBP (p < 0.0002) and trichlormethiazide significantly decreased morning UACR (p = 0.03). Amlodipine decreased morning UACR in patients with microalbuminuria based on casual spot urine samples (p = 0.048). However, multivariate analysis showed that only higher home SBP and UACR at week 8, but not any additional treatments, were significantly associated with UACR reduction between week 8 and week 16. In conclusion, crucial points of the effects of combination therapy on UACR were basal UACR and SBP levels. The effect of trichlormethiazide or amlodipine treatment in combination with irbesartan treatment on microalbuminuria needs to be reexamined based on a larger sample size after considering basal UACR and SBP levels.

Phosphorus Sorption Characteristics in Aluminum-based Water Treatment Residuals Reacted with Dairy Wastewater: 1. Isotherms, XRD, and SEM-EDS Analysis.

PubMed

Zohar, Iris; Massey, Michael S; Ippolito, James A; Litaor, M Iggy

2018-05-01

We examined P sorption characteristics in Al-based water treatment residuals (Al-WTR) generated from slightly alkaline surface water and in an organic residual composite (WW-Al/O-WTR), produced by using the Al-WTR to treat organic-rich and high P concentration dairy wastewater. Solids from both residuals were examined using scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD), and exposed to P additions of 0 to 4000 mg L in a sorption experiment. The Al-WTR removed ∼97% of the added P, whereas WW-Al/O-WTR removed only 78% of the added P in the addition range of 0 to 100 mg P L. With P additions of ≥100 mg L, the removal rate declined to <38% by Al-WTR and to 16% by WW-Al/O-WTR, possibly implying a change in sorption mechanisms. Analysis by XRD indicated that the major mineral was calcite, with some silica and poorly crystalline Al hydroxides. Analysis by SEM-EDS, which used three-element overlay maps of the residual surfaces, indicated that P was sparsely sorbed on both calcic and Al (hydr)oxide surfaces, along with a few clusters, even at low P concentrations of the treated waters. Ternary clusters of P, Al, and Ca were more abundant on the WW-Al/O-WTR. Carbon distribution suggested that organic substances covered Al surfaces. Sorption of P onto WW-Al/O-WTR may be reversible due to relatively weak Ca-P and Al-P bonds induced by the slight alkaline nature and in the presence of organic moieties, enhancing the WW-Al/O-WTR potential to act as a P source, rather than a P sink, in agricultural applications. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

In Silico Testing of an Artificial-Intelligence-Based Artificial Pancreas Designed for Use in the Intensive Care Unit Setting

PubMed Central

DeJournett, Leon; DeJournett, Jeremy

2016-01-01

Background: Effective glucose control in the intensive care unit (ICU) setting has the potential to decrease morbidity and mortality rates which should in turn lead to decreased health care expenditures. Current ICU-based glucose controllers are mathematically derived, and tend to be based on proportional integral derivative (PID) or model predictive control (MPC). Artificial intelligence (AI)–based closed loop glucose controllers may have the ability to achieve control that improves on the results achieved by either PID or MPC controllers. Method: We conducted an in silico analysis of an AI-based glucose controller designed for use in the ICU setting. This controller was tested using a mathematical model of the ICU patient’s glucose-insulin system. A total of 126 000 unique 5-day simulations were carried out, resulting in 107 million glucose values for analysis. Results: For the 7 control ranges tested, with a sensor error of ±10%, the following average results were achieved: (1) time in control range, 94.2%, (2) time in range 70-140 mg/dl, 97.8%, (3) time in hyperglycemic range (>140 mg/dl), 2.1%, and (4) time in hypoglycemic range (<70 mg/dl), 0.09%. In addition, the average coefficient of variation (CV) was 11.1%. Conclusions: This in silico study of an AI-based closed loop glucose controller shows that it may be able to improve on the results achieved by currently existing ICU-based PID/MPC controllers. If these results are confirmed in clinical testing, this AI-based controller could be used to create an artificial pancreas system for use in the ICU setting. PMID:27301982

In Silico Testing of an Artificial-Intelligence-Based Artificial Pancreas Designed for Use in the Intensive Care Unit Setting.

PubMed

DeJournett, Leon; DeJournett, Jeremy

2016-11-01

Effective glucose control in the intensive care unit (ICU) setting has the potential to decrease morbidity and mortality rates which should in turn lead to decreased health care expenditures. Current ICU-based glucose controllers are mathematically derived, and tend to be based on proportional integral derivative (PID) or model predictive control (MPC). Artificial intelligence (AI)-based closed loop glucose controllers may have the ability to achieve control that improves on the results achieved by either PID or MPC controllers. We conducted an in silico analysis of an AI-based glucose controller designed for use in the ICU setting. This controller was tested using a mathematical model of the ICU patient's glucose-insulin system. A total of 126 000 unique 5-day simulations were carried out, resulting in 107 million glucose values for analysis. For the 7 control ranges tested, with a sensor error of ±10%, the following average results were achieved: (1) time in control range, 94.2%, (2) time in range 70-140 mg/dl, 97.8%, (3) time in hyperglycemic range (>140 mg/dl), 2.1%, and (4) time in hypoglycemic range (<70 mg/dl), 0.09%. In addition, the average coefficient of variation (CV) was 11.1%. This in silico study of an AI-based closed loop glucose controller shows that it may be able to improve on the results achieved by currently existing ICU-based PID/MPC controllers. If these results are confirmed in clinical testing, this AI-based controller could be used to create an artificial pancreas system for use in the ICU setting. © 2016 Diabetes Technology Society.

Porous Graphene Sponge Additives for Lithium Ion Batteries with Excellent Rate Capability.

PubMed

Cheng, Qian

2017-04-19

Rate capability as well as power performance of lithium ion batteries (LiBs) is becoming more and more important, especially as the application targets of LiBs move from mobile devices to transportation, such as EVs and HEVs. In this research, we report porous graphene sponge additives for both anode and cathode materials for better rate performance. The charge capacity retention improved from 56% to 77% at 6C and from 7% to 45% at 10C with 0.5 wt% added to the anode, while the discharge capacity retention at the 6C rate improved from 43% to 76% and the 10C rate discharge improved from 16% to 40% with the same amount of MG added to the cathode. The cyclability at high rate was also improved with the MG additive. Moreover, preparation of the MG was facile, cost-effective, and compatible with commercially available active materials. These results demonstrate the suitability of MG for use with LiB additives to ensure better rate capability and high rate cyclability.

A kinetic study of struvite precipitation recycling technology with NaOH/Mg(OH)2 addition.

PubMed

Yu, Rongtai; Ren, Hongqiang; Wang, Yanru; Ding, Lili; Geng, Jingji; Xu, Ke; Zhang, Yan

2013-09-01

Struvite precipitation recycling technology is received wide attention in removal ammonium and phosphate out of wastewater. While past study focused on process efficiency, and less on kinetics. The kinetic study is essential for the design and optimization in the application of struvite precipitation recycling technology. The kinetics of struvite with NaOH/Mg(OH)2 addition were studied by thermogravimetry analysis with three rates (5, 10, 20 °C/min), using Friedman method and Ozawa-Flynn-Wall method, respectively. Degradation process of struvite with NaOH/Mg(OH)2 addition was three steps. The stripping of ammonia from struvite was mainly occurred at the first step. In the first step, the activation energy was about 70 kJ/mol, which has gradually declined as the reaction progress. By model fitting studies, the proper mechanism function for struvite decomposition process with NaOH/Mg(OH)2 addition was revealed. The mechanism function was f(α)=α(α)-(1-α)(n), a Prout-Tompkins nth order (Bna) model. Copyright © 2013 Elsevier Ltd. All rights reserved.

Aminocarminic acid in E120-labelled food additives and beverages.

PubMed

Sabatino, Leonardo; Scordino, Monica; Gargano, Maria; Lazzaro, Francesco; Borzì, Marco A; Traulo, Pasqualino; Gagliano, Giacomo

2012-01-01

An analytical method was developed for investigating aminocarminic acid occurrence in E120-labelled red-coloured-beverages and in E120 additives, with the aim of controlling the purity of the carmine additive in countries where the use of aminocarminic acid is forbidden. The carminic acid and the aminocarminic acid were separated by high-performance liquid chromatography-photodiode array-tandem mass spectrography (HPLC-PDA-MS/MS). The method was statistically validated. The regression lines, ranging from 10 to 100 mg/L, showed r(2 )> 0.9996. Recoveries from 97% to 101% were obtained for the fortification level of 50 mg/L; the relative standard deviations did not exceed 3%. The LODs were below 2 mg/L, whereas the LOQs did not exceed 4 mg/L. The method was successfully applied to 27 samples of commercial E120-labelled red-coloured beverages and E120 additives, collected in Italy during quality control investigations conducted by the Ministry. The results demonstrated that more than 50% of the samples contained aminocarminic acid, evidencing the alarming illicit use of this semi-synthetic carmine acid derivative.

The Effect of Copper and Selenium Nanocarboxylates on Biomass Accumulation and Photosynthetic Energy Transduction Efficiency of the Green Algae Chlorella Vulgaris

NASA Astrophysics Data System (ADS)

Mykhaylenko, Natalia F.; Zolotareva, Elena K.

2017-02-01

Nanoaquachelates, the nanoparticles with the molecules of water and/or carboxylic acids as ligands, are used in many fields of biotechnology. Ultra-pure nanocarboxylates of microelements are the materials of spatial perspective. In the present work, the effects of copper and selenium nanoaquachelates carboxylated with citric acid on biomass accumulation of the green algae Chlorella vulgaris were examined. Besides, the efficiency of the reactions of the light stage of photosynthesis was estimated by measuring chlorophyll a fluorescence. The addition of 0.67-4 mg L-1 of Cu nanocarboxylates resulted in the increase in Chlorella biomass by ca. 20%; however, their concentrations ranging from 20 to 40 mg L-1 strongly inhibited algal growth after the 12th day of cultivation. Se nanocarboxylates at 0.4-4 mg L-1 concentrations also stimulated the growth of C. vulgaris, and the increase in biomass came up to 40-45%. The addition of Se nanocarboxylates at smaller concentrations (0.07 or 0.2 mg L-1) at first caused the retardation of culture growth, but that effect disappeared after 18-24 days of cultivation. The addition of 2-4 mg L-1 of Cu nanocarboxylates or 0.4-4 mg L-1 of Se nanocarboxylates caused the evident initial increase in such chlorophyll a fluorescence parameters as maximal quantum yield of photosystem II photochemistry ( F v/ F m) and the quantum yield of photosystem II photochemistry in the light-adapted state ( F v'/ F m'). Photochemical fluorescence quenching coefficients declined after 24 days of growth with Cu nanocarboxylates, but they increased after 6 days of the addition of 2 or 4 mg L-1 Se nanocarboxylates. Those alterations affected the overall quantum yield of the photosynthetic electron transport in photosystem II.

Advances and Achievements in In Situ Analysis of Corrosion and Structure–Property Relationship in Mg Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orlov, D.; Joshi, V.

Every year, TMS Magnesium Committee carefully selects a special topic in magnesium (Mg) related research and development not only having the hottest subject from both academic and industrial perspectives but also demonstrating major achievements within this subject. Following last year’s topic on Mg microallying [1], this year’s focus is on in-situ methods and associated techniques in their broad definition spanning from laboratory- to large- scale facilities to process monitoring. The applications of in-situ techniques have a wide spectrum from the analysis of melts and liquid-solid transitions to solid-state phenomena during thermo-mechanical processing and heat treatments to surface interactions with variousmore » environments. Therefore, such works are of significant interest to scientists working in the area of Mg alloy development as well as to a much broader audience from both academia and industry. This interest is primarily caused by challenges in the analysis of structure-property relationship in Mg alloys, and even cursory glance of literature reveals sharp increase of publications relevant to this topic recently. For instance, very high reactivity of Mg as well as its well-known propensity to substantially alter structure upon unloading in mechanical testing makes it difficult to understand and thus to simulate correlation between microstructures observed in post-mortem analysis and physical processes during testing or fabrication. However, recent advances in in-situ analysis based on large-scale research facilities such as neutron scattering and synchrotron radiation sources as well as microscopy-based, acoustic emission, and other more traditional techniques allowed significant achievements. Apart from apparent development of relevant experimental techniques, a significant part of this success should also be attributed to increasing accessibility of the facilities and simplification of their use from a user perspective. The selection of articles in this special topic is quite far from comprehensive review covering all aspects of in-situ methods available for metallic materials development. However, this was not the purpose in any case. Instead, this selection is intended to present several studies on Mg alloys and Mg-based composites with the use of in-situ techniques. In addition, it overviews two techniques, ‘Acoustic Emission’ (AE) and ‘Ambient-Pressure X-ray Photoelectron Spectroscopy’ (AP-XPS), that are rather novel to the Mg community. These studies are supposed to give readers representative examples of such techniques potential and to help in navigating the spectrum of modern state-of-the-art analytical methods facilitating the development of Mg alloys. These articles are organized in the order corresponding to typical Mg alloy lifecycle from material preparation and solidification to thermo-mechanical processing and product fabrication to degradation.« less

Dexketoprofen/tramadol: randomised double-blind trial and confirmation of empirical theory of combination analgesics in acute pain.

PubMed

Moore, R Andrew; Gay-Escoda, C; Figueiredo, R; Tóth-Bagi, Z; Dietrich, T; Milleri, S; Torres-Lagares, D; Hill, C M; García-García, A; Coulthard, P; Wojtowicz, A; Matenko, D; Peñarrocha-Diago, M; Cuadripani, S; Pizà-Vallespir, B; Guerrero-Bayón, C; Bertolotti, M; Contini, M P; Scartoni, S; Nizzardo, A; Capriati, A; Maggi, C A

2015-01-01

Combination analgesics are effective in acute pain, and a theoretical framework predicts efficacy for combinations. The combination of dexketoprofen and tramadol is untested, but predicted to be highly effective. This was a randomised, double-blind, double-dummy, parallel-group, placebo-controlled, single-dose trial in patients with moderate or severe pain following third molar extraction. There were ten treatment arms, including dexketoprofen trometamol (12.5 mg and 25 mg) and tramadol hydrochloride (37.5 mg and 75 mg), given as four different fixed combinations and single components, with ibuprofen 400 mg as active control as well as a placebo control. The study objective was to evaluate the superior analgesic efficacy and safety of each combination and each single agent versus placebo. The primary outcome was the proportion of patients with at least 50 % max TOTPAR over six hours. 606 patients were randomised and provided at least one post-dose assessment. All combinations were significantly better than placebo. The highest percentage of responders (72%) was achieved in the dexketoprofen trometamol 25 mg plus tramadol hydrochloride 75 mg group (NNT 1.6, 95% confidence interval 1.3 to 2.1). Addition of tramadol to dexketoprofen resulted in greater peak pain relief and greater pain relief over the longer term, particularly at times longer than six hours (median duration of 8.1 h). Adverse events were unremarkable. Dexketoprofen trometamol 25 mg combined with tramadol hydrochloride 75 mg provided good analgesia with rapid onset and long duration in a model of moderate to severe pain. The results of the dose finding study are consistent with pre-trial calculations based on empirical formulae. EudraCT (2010-022798-32); Clinicaltrials.gov (NCT01307020).

In Vitro and in Vivo Studies on Biomedical Magnesium Low-Alloying with Elements Gadolinium and Zinc for Orthopedic Implant Applications.

PubMed

Bian, Dong; Deng, Jiuxu; Li, Nan; Chu, Xiao; Liu, Yang; Li, Wenting; Cai, Hong; Xiu, Peng; Zhang, Yu; Guan, Zhenpeng; Zheng, Yufeng; Kou, Yuhui; Jiang, Baoguo; Chen, Rongshi

2018-02-07

Ternary magnesium alloys with low combined addition of elements gadolinium and zinc were developed in the present work, with their microstructures, mechanical properties, in vitro degradation behaviors, and cytotoxicity being systematically studied. Furthermore, the Mg-1.8Zn-0.2Gd alloy, with the best in vitro performance, was implanted into Sprague Dawley rats to examine its in vivo degradation performance for up to 6 months. It was found that Mg-1.8Zn-0.2Gd, composed of a single α-Mg phase, owned excellent strength and toughness that were comparable to the CE marked MAGNEZIX, the mischmetal added Mg alloy. Owing to the uniform single-phased microstructure, the degradation rate of this alloy was around 0.12 mm/y measured by electrochemical testing, which was comparable to high purity magnesium. Moreover, the Mg-1.8Zn-0.2Gd alloy exhibited no cytotoxicity to L929, MG63, and VSMC cells. In vivo degradation characterized by micro-computed tomography revealed that the Mg-1.8Zn-0.2Gd implant could maintain structural integrity in the first 2 months, and serious degradation could be observed after 6 months. A remarkable 100% survival rate of experimental animals was observed with no negative effects on bone tissues. The implant and the surrounding bone were well integrated within 2 months, implying good biocompatibility and osteoconductivity of the experimental alloy. On the basis of the above findings, the feasibility of Mg-Zn-Gd alloys for use as orthopedic implants was systematically discussed. This study provides a new strategy for development of high-performance Mg-rare earth (RE)-based alloys with superior mechanical properties and corrosion resistance while effectively avoiding the possible standing toxic effect of RE elements.

How does airway exposure of aflatoxin B1 affect serum albumin adduct concentrations? Evidence based on epidemiological study and animal experimentation.

PubMed

Mo, Xianwei; Lai, Hao; Yang, Yang; Xiao, Jun; He, Ke; Liu, Chao; Chen, Jiansi; Lin, Yuan

2014-08-01

Aflatoxin B1 (AFB1) airway inhalation represents an additional route of exposure to this toxin. However, the association between AFB1 inhalation and serum AFB1 albumin adducts remains unclear. The aim of this study was to explore the association between airway exposure to AFB1 and serum AFB1 albumin adduct concentrations via an epidemiological study, as well as in an AFB1 airway exposure animal model. Our epidemiological study was conducted in a sugar factory in the Guangxi Autonomous Region of China. In order to examine fungal contamination, air samples were obtained in the workshop and areas outside the workshop, such as the office and nearby store. Dust samples were also collected from the bagasse warehouse and presser workshop, and were analyzed using an indirect competitive enzyme-linked immunosorbent assay (ELISA). Additionally, blood samples were collected from a total of 121 workshop workers, and a control group (n = 80) was comprised of workers who undertook administrative tasks or other work outside the workshop. The animal experiment was conducted in the laboratory animal center of Guangxi Medical University, where a total of 60 adult male rabbits were involved in this study. By intubation, AFB1 was administered in three groups of rabbits daily, at dose rates of 0.075, 0.05 and 0.025 mg/kg/day for a period of 7 days. Blood samples were collected on day 1, day 3, day 7 and day 21, and the measurements of the AFB1 albumin adducts in the serum were performed by a double antibody sandwich ELISA. The epidemiological study showed that serum albumin adducts were detected in 67 workshop workers (55.37%), and the values ranged 6.4 pg/mg albumin to 212 pg/mg albumin (mean value: 51 ± 4.62 pg/mg albumin). In contrast, serum albumin adducts were detected in only 7 control group participants, with the values ranging from 9 pg AFB1/mg albumin to 59 pg/mg albumin (mean value: 20 ± 13.72 pg/mg albumin). The animal experiment revealed that the rabbits had detectable levels of AFB1 in their serum with a minimum effective dose of 0.05 mg/kg/day; while 11 of 17 (64.71%) rabbits had detectable levels of AFB1 albumin adducts in the high exposure group (0.075 mg/kg/day), and only 5 rabbits (26.32%) had detectable levels of AFB1 albumin adducts in the moderate exposure group (0.05 mg/kg/day). No rabbits had detectable levels of AFB1 albumin adducts in the low exposure group (0.025 mg/kg/day). Our results demonstrated that only exposure to a certain level of AFB1 would result in detectable levels of serum AFB1 albumin adducts. Interventional programs aimed at reducing exposure to AFB1 by inhalation are urgently needed in high-risk populations. Additional large-sample, well-designed randomized controlled trials are needed to further confirm our results.

Insight into destabilization mechanism of Mg-based hydrides interstitially co-doped with nonmetals: a DFT study

NASA Astrophysics Data System (ADS)

Wu, Zhen; Zhu, Luying; Yang, Fusheng; Zhang, Zaoxiao; Nyamsi, Serge N.

2018-04-01

Mg-based metal hydride is one of the most promising materials for hydrogen energy storage. However, the high thermal stability due to strong bonding effects between the atoms limits its practical application. In order to reduce the thermal stability, a method of doping double nonmetals into Mg-based system was proposed in this study. The density functional theory (DFT) calculation results showed that the thermal stabilities of both the B-N co-doped Mg-based alloy and its hydride are reduced compared with pure Mg-based system. The relative formation enthalpies of the alloy and its hydride are 0.323 and 0.595 eV atom-1, respectively. The values are much higher than those for either singly B- or N-doped Mg-based system. The more significant destabilization by doping double nonmetal elements than single element is mainly attributed to a dual effect in weakening Mg-Ni/NiH4 bonds, caused by criss-cross interactions between B-Ni and N-Mg bonds.

Effect of green tea (Camellia sinensis) extract and pre-freezing equilibration time on the post-thawing quality of ram semen cryopreserved in a soybean lecithin-based extender.

PubMed

Mehdipour, Mahdieh; Daghigh Kia, Hossein; Najafi, Abouzar; Vaseghi Dodaran, Hossein; García-Álvarez, Olga

2016-12-01

The aim of this study was to determine the effect of Camellia sinensis extract as antioxidant supplement and pre-freezing equilibration times in a soybean lecithin extender for freezing ram semen. In this study, a total of 20 ejaculates were collected from four Ghezel rams and diluted with extenders (1.5% soybean lecithin, 7% glycerol) containing no supplements (control) and Camellia sinensis extract (5, 10, and 15 mg/L) and cryopreserved, immediately after thermal equilibrium was reached at 5 °C (0 h), or 4 h after equilibration. Sperm motility characteristics, membrane integrity, abnormal morphology, mitochondria activity, apoptotic status, MDA and antioxidant activities (GPx, SOD and total antioxidant capacity (TAC)) were evaluated following freeze-thawing. Camellia sinensis extract at level 10 mg/L led to the highest total and progressive motilities percentages, in comparison to other treatments (P < 0.05). Our results showed that Camellia sinensis extract at level of 5 and 10 mg/L led to higher plasma membrane integrity, mitochondria activity and Total antioxidant capacity (TAC) in comparison to the level of 15 mg/L and control group (P < 0.05). Camellia sinensis extract at 10 mg/L level produced the highest percentage of live spermatozoa and the lowest apoptotic spermatozoa in comparison to all treatments (P < 0.05). In addition, level of MDA formation significantly decreased at this concentration, 10 mg/L, compared to all treatments (P < 0.05). No differences (P > 0.05) were observed between equilibration times (0 h vs. 4 h) for sperm samples incubated with or without different concentrations of Camellia sinensis extract. In conclusion, addition of Camellia sinensis extract at level of 10 mg/L can improve post-thawing quality of ram semen cryopreserved in a soybean lecithin extender. However, further research is needed to standardize the process of Camellia sinensis extraction and specially for identifying which compounds are responsible of its beneficial effect on ram sperm cryopreservation. Copyright © 2016 Elsevier Inc. All rights reserved.

Hydrogen storage properties of nanosized MgH2-0.1TiH2 prepared by ultrahigh-energy-high-pressure milling.

PubMed

Lu, Jun; Choi, Young Joon; Fang, Zhigang Zak; Sohn, Hong Yong; Rönnebro, Ewa

2009-11-04

Magnesium hydride (MgH(2)) is an attractive candidate for solid-state hydrogen storage applications. To improve the kinetics and thermodynamic properties of MgH(2) during dehydrogenation-rehydrogenation cycles, a nanostructured MgH(2)-0.1TiH(2) material system prepared by ultrahigh-energy-high-pressure mechanical milling was investigated. High-resolution transmission electron microscope (TEM) and scanning TEM analysis showed that the grain size of the milled MgH(2)-0.1TiH(2) powder is approximately 5-10 nm with uniform distributions of TiH(2) among MgH(2) particles. Pressure-composition-temperature (PCT) analysis demonstrated that both the nanosize and the addition of TiH(2) contributed to the significant improvement of the kinetics of dehydrogenation and hydrogenation compared to commercial MgH(2). More importantly, PCT cycle analysis demonstrated that the MgH(2)-0.1TiH(2) material system showed excellent cycle stability. The results also showed that the DeltaH value for the dehydrogenation of nanostructured MgH(2)-0.1TiH(2) is significantly lower than that of commercial MgH(2). However, the DeltaS value of the reaction was also lower, which results in minimum net effects of the nanosize and the addition of TiH(2) on the equilibrium pressure of dehydrogenation reaction of MgH(2).

Magnesium deficiency results in damage of nitrogen and carbon cross-talk of maize and improvement by cerium addition.

PubMed

Zhao, Haiquan; Zhou, Qiuping; Zhou, Min; Li, Chunxiao; Gong, Xiaolan; Liu, Chao; Qu, Chunxiang; Si, Wenhui; Hong, Fashui

2012-07-01

Magnesium (Mg) deficiency has been reported to affect plant photosynthesis and growth, and cerium (Ce) was considered to be able to improve plant growth. However, the mechanisms of Mg deficiency and Ce on plant growth remain poorly understood. The main aim of this work is to identify whether or not Mg deprivation affects the interdependent nitrogen and carbon assimilations in the maize leaves and whether or not Ce modulates the assimilations in the maize leaves under Mg deficiency. Maize plants were cultivated in Hoagland’s solution. They were subjected to Mg deficiency and to cerium chloride administration in the Mg-present Hoagland’s media and Mg-deficient Hoagland’s media.After 2 weeks,we measured chlorophyll (Chl) a fluorescence and the activities of nitrate reductase (NR), sucrose-phosphate synthase(SPS), and phosphoenolpyruvate carboxylase (PEPCase)in metabolic checkpoints coordinating primary nitrogen and carbon assimilations in the maize leaves. The results showed that Mg deficiency significantly inhibited plant growth and decreased the activities of NR, SPS, and PEPCase and the synthesis of Chl and protein. Mg deprivation in maize also significantly decreased the oxygen evolution, electron transport,and efficiency of photochemical energy conversion by photosystem II (PSII). However, Ce addition may promote nitrogen and carbon assimilations, increase PSII activities,and improve maize growth under Mg deficiency. Moreover,our findings would help promote usage of Mg or Ce fertilizers in maize production.

Improving properties of Mg with Al–Cu additions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rashad, Muhammad, E-mail: rashadphy87@gmail.com; National Engineering Research Center for Magnesium Alloys, Chongqing University, Chongqing 400044; Pan, Fusheng, E-mail: fspan@cqu.edu.cn

The present work reports improvement in tensile properties of the Mg matrix reinforced with micron-sized copper–aluminum particulate hybrids. The Al–Cu particulate hybrids were incorporated into the Mg matrix through powder metallurgy method. The synthesized alloys exhibited homogeneously dispersed Mg{sub 2}Cu particles in the matrix, therefore leading to a 110% increase in yield strength (221 MPa) and a 72% enhancement in ultimate tensile strength (284 MPa) by addition of 1.0 wt.%Al–0.6 wt.%Cu particle hybrids. Optical microscopy, scanning election microscopy, transmission electron microscopy and X-ray diffraction were used to investigate the microstructure and intermetallic phases of the synthesized alloys. - Highlights: •more » Mg matrix is reinforced with Al–Cu particulate hybrids. • Powder metallurgic method is used to fabricate the alloys. • Tensile strength and ductility were increased simultaneously.« less

The ineffectiveness of (±)-carnitine preventing the twitchings of striated frog muscle in 0.7% sodium chloride solution

PubMed Central

Friebel, H.

1959-01-01

The spontaneous twitchings of isolated frog sartorius muscles in 0.7% NaCl solution have been studied. Addition of 1 mg./ml. of (±)-carnitine hydrochloride, or of (±)-carnitine base, to the bath fluid had no influence on the spontaneous activity of the muscles, their excitability or their ability to liberate potassium. This indicates that carnitine is not a natural inhibitor of striated frog muscle. Fluids enriched with potassium either from twitching muscle or by addition of KCl inhibited the activity of muscles reversibly. PMID:13825014

The effect of thermal and organic additive in morphology of ceramic based silicate

NASA Astrophysics Data System (ADS)

Ginting, J.; Bangun, N.; Sembiring, H. Br; Putri, N. K.

2017-04-01

M-Silicate (M = Mg, Ca) has been prepared by exchange metal reaction from M-Chloride salts and sodium silicate. The resulting white solid of chloride salts then heated at 700, 800, 900 and 1000 °C. Due to increase the porosity of M-Silicate, 1,2-propanediol, oleic acid and glycerol were added, then formed M-silicates were heated at 800 °C. Then, obtained white solid M-Silicates were characterized by Scanning Electron Microscopy (SEM). SEM images show the variance of surface morphology when the temperature increases. The addition of organic compounds is involved in surface modification.

Single dose oral paracetamol (acetaminophen) with codeine for postoperative pain in adults

PubMed Central

Toms, Laurence; Derry, Sheena; Moore, R Andrew; McQuay, Henry J

2014-01-01

Background This is an updated version of the Cochrane review published in Issue 4, 1998. Combining drugs from different classes with different modes of action may offer opportunity to optimise efficacy and tolerability, using lower doses of each drug to achieve the same degree of pain relief. Previously we concluded that addition of codeine to paracetamol provided additional pain relief, but at expense of additional adverse events. New studies have been published since. This review sought to evaluate efficacy and safety of paracetamol plus codeine using current data, and compare findings with other analgesics evaluated similarly. Objectives Assess efficacy of single dose oral paracetamol plus codeine in acute postoperative pain, increase in efficacy due to the codeine component, and associated adverse events. Search methods We searched CENTRAL, MEDLINE, EMBASE, the Oxford Pain Relief Database in October 2008 for this update. Selection criteria Randomised, double-blind, placebo-controlled trials of paracetamol plus codeine, compared with placebo or the same dose of paracetamol alone, for relief of acute postoperative pain in adults. Data collection and analysis Two authors assessed trial quality and extracted data. The area under the “pain relief versus time” curve was used to derive proportion of participants with paracetamol plus codeine and placebo or paracetamol alone experiencing least 50% pain relief over four-to-six hours, using validated equations. Number-needed-to-treat-to-benefit (NNT) was calculated using 95% confidence intervals (CIs). Proportion of participants using rescue analgesia over a specified time period, and time to use of rescue analgesia, were sought as additional measures of efficacy. Information on adverse events and withdrawals were collected. Main results Twenty-six studies, with 2295 participants, were included comparing paracetamol plus codeine with placebo. Significant dose response was seen for the outcome of at least 50% pain relief over four-to-six hours, with NNTs of 2.2 (95% CI 1.8 to 2.9) for 800 to 1000 mg paracetamol plus 60 mg codeine, 3.9 (2.9 to 4.5) for 600 to 650 mg paracetamol plus 60 mg codeine, and 6.9 (4.8 to 12) for 300 mg paracetamol plus 30 mg codeine. Time to use of rescue medication was over four hours with paracetamol plus codeine and two hours with placebo. The NNT to prevent remedication was 5.6 (4.0 to 9.0) for 600 mg paracetamol plus 60 mg codeine over four to six hours. Adverse events increased of mainly mild to moderate severity with paracetamol plus codeine than placebo. Fourteen studies, with 926 participants, were included in the comparison of paracetamol plus codeine with the same dose of paracetamol alone. Addition of codeine increased proportion of participants achieving at least 50% pain relief over four-to-six hours by 10 to 15%, increased time to use of rescue medication by about one hour, and reduced proportion of participants needing rescue medication by about 15% (NNT to prevent remedication 6.9 (4.2 to 19). Adverse events were mainly mild to moderate in severity and incidence did not differ between groups. Authors’ conclusions This update confirms previous findings that combining paracetamol with codeine provided clinically useful levels of pain relief in about 50% of patients with moderate to severe postoperative pain, compared with under 20% with placebo. New information for remedication shows that the combination extended the duration of analgesia by about one hour compared to treatment with the same dose of paracetamol alone. At higher doses, more participants experienced adequate pain relief, but the amount of information available for the 1000 mg paracetamol plus 60 mg codeine dose was small, and based on limited information. PMID:19160199

Use of reversible hydrides for hydrogen storage

NASA Technical Reports Server (NTRS)

Darriet, B.; Pezat, M.; Hagenmuller, P.

1980-01-01

The addition of metals or alloys whose hydrides have a high dissociation pressure allows a considerable increase in the hydrogenation rate of magnesium. The influence of temperature and hydrogen pressure on the reaction rate were studied. Results concerning the hydriding of magnesium rich alloys such as Mg2Ca, La2Mg17 and CeMg12 are presented. The hydriding mechanism of La2Mg17 and CeMg12 alloys is given.

Effect of combined treatment with diuretics and gabapentin on convulsive threshold in mice.

PubMed

Łukawski, Krzysztof; Swiderska, Grajyna; Czuczwar, Stanisław J

2013-01-01

Research data show that diuretics can have anticonvulsant properties. This study examined effects of ethacrynic acid, a loop diuretic, and hydrochlorothiazide, a thiazide-type diuretic, on the anticonvulsant activity of gabapentin, a newer antiepileptic drug, in the maximal electroshock seizure threshold test in mice. Diuretics were administered intraperitoneally (ip.) both acutely (single dose) and chronically (once daily for seven days). Electroconvulsions were produced by an alternating current (50 Hz, 500 V, 0.2 s stimulus duration) delivered via ear-clip electrodes by a generator. Additionally, the influence of combined treatment with the diuretics and gabapentin on motor performance in the chimney test has been assessed. In the current study, ethacrynic acid at the chronic dose of 12.5 mg/kg and the single dose of 100 mg/kg did not affect the anticonvulsant activity of gabapentin. Similarly, hydrochlorothiazide (100 mg/kg), both in acute and chronic experiments, had no effect on the gabapentin action. On the other hand, in the chimney test, the combined treatment with ethacrynic acid (100 mg/kg) and gabapentin (50 mg/kg) significantly impaired motor performance in mice. Based on the current preclinical findings, it can be suggested that the diuretics should not affect the anticonvulsant action of gabapentin in epileptic patients. However, the combination of ethacrynic acid with gabapentin may cause neurotoxicity.

Mini-TES Observations of Comanche Carbonate and Its Distribution

NASA Technical Reports Server (NTRS)

Ruff, Steven W.; Morris, Richard V.

2010-01-01

The discovery by the Spirit rover of outcrops rich in Mg-Fe carbonate [Morris et al., 2010] represents another manifestation of a diverse aqueous history in Gusev crater. In 2005, observations by the Moessbauer spectrometer (MB) on outcrops dubbed Comanche provided initial indication of Fe-Mg carbonate that was subsequently supported by analysis of elemental data from the Alpha Particle X-ray Spectrometer (APXS). The recognition of a carbonate component in thermal infrared spectra measured by the Miniature Thermal Emission Spectrometer (Mini-TES) was significantly delayed due to dust contamination of the instrument's optics. With the implementation of a viable dust correction, the Comanche spectra were revisited and presented clear and compelling evidence for a Mg-Fe carbonate component that could be as much as a third of the total mineral abundance. The data from all three instruments in combination are best matched by Mg-Fe carbonate with an abundance of 16-34 wt%. Mini-TES spectra were acquired for 12 targets at various locations on the Comanche (4-5 m long) and Comanche Spur (1-2 m long) outcrops, the latter being the location of the MB and APXS measurements. The two outcrops are spectrally comparable and share similar morphology and texture based on color images from the Panoramic Camera (Pancam). The highest quality Mini-TES spectrum comes from the larger Comanche outcrop on a target named Saupitty. Linear least squares modeling of the Saupitty spectrum employed a library of laboratory spectra tailored for consistency with the APXS and MB data and included spectra representing Martian dust, a slope spectrum to account for any temperature determination errors, and a blackbody spectrum to account for differences in spectral contrast between the laboratory and Mini-TES spectrum. Successful modeling of the Comanche Saupitty spectrum required one or more carbonate phases to obtain a good fit. Excluding all carbonates from the full starting library more than doubled the root-mean-squared error of the model fit (0.147% vs. 0.299%). Because Mg-Fe carbonate and Ca-Mg carbonate (dolomite) are so spectrally similar over the range used for modeling, both provide a comparable fit. However, Carich carbonates like dolomite are precluded based on APXS data and are inconsistent with MB results. The Comanche carbonate rocks are stratigraphically above a set of olivine-rich volcaniclastic rocks known as Algonquin class that mantle the Haskin Ridge feature of the Columbia Hills. Based on 50 Mini-TES observations, the Comanche outcrops are the only rocks that host abundant carbonate. However, a target at the base of the larger Comanche outcrop appears spectrally transitional between the carbonate and olivine units. This transitional spectral character applies to additional outcrops a few 10s of meters away from Comanche that also appear stratigraphically transitional. Additional work will attempt to establish whether we are seeing an alteration horizon or depositional unit associated with the emplacement Comanche carbonate.

Cost Per Additional Responder Associated With Ixekizumab and Etanercept in the Treatment of Moderate-to-Severe Psoriasis.

PubMed

Feldman, Steven R; Foster, Shonda A; Zhu, Baojin; Burge, Russel; Al Sawah, Sarah; Goldblum, Orin M

2017-12-01

BACKGROUND: Newer psoriasis treatments can achieve greater levels of efficacy than older systemic therapies; however, current psoriasis costs are substantial. We sought to estimate costs per additional responder associated with ixekizumab and etanercept, versus placebo, using efficacy data from phase 3 clinical trials (UNCOVER-2 and UNCOVER-3). METHODS: In UNCOVER-2/UNCOVER-3, patients received subcutaneous placebo, etanercept 50 mg twice weekly (BIW), or ixekizumab one 80 mg injection every 2 weeks (Q2W) after a 160-mg starting dose. Twelve-week induction-phase Psoriasis Area and Severity Index (PASI) 75, PASI 90, and PASI 100 response rates for ixekizumab, etanercept, and placebo were obtained from pooled data from the overall and United States (US) subgroup intention-to-treat (ITT) populations, and used to calculate numbers needed to treat (NNTs) to achieve one additional PASI 75, PASI 90, or PASI 100 response for ixekizumab Q2W and etanercept BIW versus placebo. Twelve-week drug costs per patient were calculated based on the UNCOVER-2/UNCOVER-3 dosing schedule and wholesale acquisition costs. Mean costs per additional responder for PASI 75, PASI 90, and PASI 100 for each treatment versus placebo were calculated for pooled UN-COVER-2/UNCOVER-3 overall and US subgroup ITT populations. RESULTS: Pooled overall ITT population: costs per additional PASI 75, PASI 90, or PASI 100 responder were US $37,540, US $46,299, or US $80,710 for ixekizumab Q2W and US $57,533, US $120,720, or US $404,695 for etanercept BIW, respectively. US subgroup ITT population: costs per additional PASI 75, PASI 90, or PASI 100 responder were US $38,165, US $49,740, or US $93,536 for ixekizumab Q2W and US $69,580, US $140,881, or US $631,875 for etanercept BIW, respectively. CONCLUSIONS: Twelve-week costs per additional responder were lower for ixekizumab Q2W than for etanercept BIW across all levels of clearance (PASI 75, PASI 90, and PASI 100) in the pooled UNCOVER-2/UNCOVER-3 overall and US subgroup ITT populations.

Maternal caffeine intake during pregnancy is associated with birth weight but not with gestational length: results from a large prospective observational cohort study

PubMed Central

2013-01-01

Background Pregnant women consume caffeine daily. The aim of this study was to examine the association between maternal caffeine intake from different sources and (a) gestational length, particularly the risk for spontaneous preterm delivery (PTD), and (b) birth weight (BW) and the baby being small for gestational age (SGA). Methods This study is based on the Norwegian Mother and Child Cohort Study conducted by the Norwegian Institute of Public Health. A total of 59,123 women with uncomplicated pregnancies giving birth to a live singleton were identified. Caffeine intake from different sources was self-reported at gestational weeks 17, 22 and 30. Spontaneous PTD was defined as spontaneous onset of delivery between 22+0 and 36+6 weeks (n = 1,451). As there is no consensus, SGA was defined according to ultrasound-based (Marsal, n = 856), population-based (Skjaerven, n = 4,503) and customized (Gardosi, n = 4,733) growth curves. Results The main caffeine source was coffee, but tea and chocolate were the main sources in women with low caffeine intake. Median pre-pregnancy caffeine intake was 126 mg/day (IQR 40 to 254), 44 mg/day (13 to 104) at gestational week 17 and 62 mg/day (21 to 130) at gestational week 30. Coffee caffeine, but not caffeine from other sources, was associated with prolonged gestation (8 h/100 mg/day, P <10-7). Neither total nor coffee caffeine was associated with spontaneous PTD risk. Caffeine intake from different sources, measured repeatedly during pregnancy, was associated with lower BW (Marsal-28 g, Skjaerven-25 g, Gardosi-21 g per 100 mg/day additional total caffeine for a baby with expected BW 3,600 g, P <10-25). Caffeine intake of 200 to 300 mg/day increased the odds for SGA (OR Marsal 1.62, Skjaerven 1.44, Gardosi 1.27, P <0.05), compared to 0 to 50 mg/day. Conclusions Coffee, but not caffeine, consumption was associated with marginally increased gestational length but not with spontaneous PTD risk. Caffeine intake was consistently associated with decreased BW and increased odds of SGA. The association was strengthened by concordant results for caffeine sources, time of survey and different SGA definitions. This might have clinical implications as even caffeine consumption below the recommended maximum (200 mg/day in the Nordic countries and USA, 300 mg/day according to the World Health Organization (WHO)) was associated with increased risk for SGA. PMID:23421532