Total fume and metal concentrations during welding in selected factories in Jeddah, Saudi Arabia.

PubMed

Balkhyour, Mansour Ahmed; Goknil, Mohammad Khalid

2010-07-01

Welding is a major industrial process used for joining metals. Occupational exposure to welding fumes is a serious occupational health problem all over the world. The degree of risk to welder's health from fumes depends on composition, concentration, and the length of exposure. The aim of this study was to investigate workers' welding fume exposure levels in some industries in Jeddah, Saudi Arabia. In each factory, the air in the breathing zone within 0.5 m from welders was sampled during 8-hour shifts. Total particulates, manganese, copper, and molybdenum concentrations of welding fumes were determined. Mean values of eight-hour average particulate concentrations measured during welding at the welders breathing zone were 6.3 mg/m(3) (Factory 1), 5.3 mg/m(3) (Factory 2), 11.3 mg/m(3) (Factory 3), 6.8 mg/m(3) (Factory 4), 4.7 mg/m(3) (Factory 5), and 3.0 mg/m(3) (Factory 6). Mean values of airborne manganese, copper, and molybdenum levels measured during welding were in the range of 0.010 mg/m(3)-0.477 mg/m(3), 0.001 mg/m(3)-0.080 mg/m(3) and 0.001 mg/m(3)-0.058 mg/m(3) respectively. Mean values of calculated equivalent exposure values were: 1.50 (Factory 1), 1.56 (Factory 2), 5.14 (Factory 3), 2.21 (Factory 4), 2.89 (Factory 5), and 1.20 (Factory 6). The welders in factories 1, 2, 3, and 4 were exposed to welding fume concentration above the SASO limit value, which may increase the risk of respiratory health problems.

Characterization of suspended particles in Everglades wetlands

USGS Publications Warehouse

Noe, G.B.; Harvey, J.W.; Saiers, J.E.

2007-01-01

We report the concentration, phosphorus (P) and nitrogen (N) content, and size and chemical fractionation of fine suspended particles (0.2-100 ??m) and colloids (3 kilodalton [kDa]-0.1 ??m) in the surface water of Everglades wetlands along regional and P-enrichment gradients. Total suspended sediment concentrations ranged from 0.7 to 2.7 mg L-1. Total particulate P concentrations increased from 0.05 ??mol L-1 to 0.31 ??mol L -1 along the P-enrichment gradient. Particles contained from 20% to 43% of total P but <12% of total N in surface water. Dissolved (<0.2 ??m) organic N contained about 90% of total N, with the 3-100-kDa colloidal size class containing the most N of any size class. The 0.45-2.7-??m size fraction held the most particulate P at all sites, whereas particulate N was most abundant in the 2.7-10-??m size class at most sites. Standard chemical fractionation of particles identified acid-hydrolyzable P as the most abundant species of particulate P, with little reactive or refractory organic P. Sequential chemical extraction revealed that about 65% of total particulate P was microbial, while about 25% was associated with humic and fulvic organic matter. The size and chemical fractionation information suggested that P-rich particles mostly consisted of suspended bacteria. Suspended particles in Everglades wetlands were small in size and had low concentrations, yet they stored a large proportion of surface-water P in intermediately reactive forms, but they held little N. ?? 2007, by the American Society of Limnology and Oceanography, Inc.

Distribution and geochemical composition of suspended particulate material in the shallow embayment of northern Thermaikos Gulf, Greece

NASA Astrophysics Data System (ADS)

Tsompanoglou, K.; Anagnostou, Ch.; Krasakopoulou, E.; Pagou, K.; Karageorgis, A. P.; Pavlidou, A.; Albanakis, K.; Tsirambides, A.

2017-07-01

The distribution and the chemical composition of Suspended Particulate Matter (SPM), in the northern Thermaikos Gulf, were studied during an annual experiment, carried out from June 2004 to June 2005. Water samples were collected at three depths (1 m below surface, 10 m depth, and 2 m above bottom) and filtered to obtain SPM, particulate organic carbon (POC), total particulate nitrogen (PNtot) and particulate phosphorus (PP) concentrations. SPM and POC concentrations exhibited strong spatial and temporal variations, related to the different environmental characteristics in the study area such as river network, biological productivity, anthropogenic interferences, wind regime, and resuspension of the bottom sediments. The highest SPM concentrations were recorded at the surface (mean = 1.45 ± 0.75 mg/l, maximum value = 11.60 mg/l) and close to the bottom (mean = 1.49 ± 0.67 mg/l, maximum value = 11.72 mg/l), creating surface and bottom nepheloid layers (SNL and BNL), respectively. The maximum values were recorded close to the river mouths; the rivers are identified as the major sources of SPM. The Axios and Aliakmon rivers supplied the gulf with particulate matter, during the entire sampling period. Chemical analysis has revealed the significant correlation among the elements Al, Si, Fe, Ti, K, V, Mg and Ba suggesting the presence of terrigenous aluminosilicate minerals. Silica and Ca have terrigenous origin, but also come from autochthonous biogenic fraction. Chromium, Ni and Co, are of natural origin and derived from mafic and ultramafic rocks of the Axios and Aliakmon watersheds. Copper and Zn are correlated with each other and their distributions follow that of POC; these two metals are derived from partially treated domestic and industrial effluents. The vertical distribution of organic matter implies increased primary production within the upper layer of the water column. Phosphorus is present mainly in an organic form. During the sampling period, the water column was well-oxygenated. Early diagenesis only affected the concentrations of Mn and to a lesser extent Fe in the recently deposited seabed sediment.

Short-term effects of particulate matter on total mortality during Saharan dust outbreaks: a case-crossover analysis in Madrid (Spain).

PubMed

Tobías, Aurelio; Pérez, Laura; Díaz, Julio; Linares, Cristina; Pey, Jorge; Alastruey, Andrés; Querol, Xavier

2011-12-15

The role of Saharan dust outbreaks on the relationship between particulate matter and daily mortality has recently been addressed in studies conducted in Southern Europe, although they have not given consistent results. We investigated the effects of coarse (PM(10-2.5)) and fine particulate matter (PM(2.5)) in Madrid on total mortality during Saharan dust and non-dust days using a case-crossover design. During Saharan dust days, an increase of 10mg/m(3) of PM(10-2.5) raised total mortality by 2.8% compared with 0.6% during non-dust days (P-value for interaction=0.0165). We found evidence of stronger adverse health effects of PM(10-2.5) during Saharan dust outbreaks effects for impacted European populations, but not for PM(2.5). Further research is needed to understand mechanisms by which Saharan dust increases risk of mortality. Copyright © 2011 Elsevier B.V. All rights reserved.

Assessment of dust exposure in a steel plant in the eastern coast of peninsular Malaysia.

PubMed

Nurul, Ainun Hamzah; Shamsul, Bahri Mohd Tamrin; Noor Hassim, Ismail

2016-11-22

Steel manufacturing produces dust, fumes, and pollutant gases that may give adverse health effects to the respiratory function of workers. Improper occupational hygiene practice in the workplace will affect both workers wellbeing and productivity. To assess the level of particulate matter [(PM2.5, PM10, and Total Particulate Matter (TPM)], and trace metal dust concentrations in different sections of a steel plant and compare with the occupational exposure values. The work environmental parameters of the particulate matters were evaluated using Indoor Air Quality, while metal dust concentrations were measured using portable personal air sampler. A total of 184 personal samples were randomly collected from workers in three major sections; steel making plant, direct reduced plant, and support group. Trace metal dust concentrations were subjected to wet mineral acid mixture digestion and analysed by atomic absorption spectrophotometer (AAS). The overall average PM2.5 concentration observed was varied according to the section: steel making plant was 0.18 mg/m3, direct reduced iron plant was 0.05 mg/m3, and support plant was 0.05 mg/m3. Average PM 10 concentration in steel making shop (SMS) plant, direct reduced (DR) plant, and support plant were 0.70 mg/m3, 0.84 mg/m3, and 0.58 mg/m3, respectively. The average TWA8 of trace metal dusts (cobalt and chromium) in all the sections exceeded 1 to 3 times the ACGIH prescribed values, OSHA PELs, NIOSH RELs as well as USECHH OSHA, whereas TWA8 concentration of nickel for each section did not exceed the occupational exposure values. The average PM2.5, PM10 and TPM did not exceed the prescribed values, while average trace metal dust concentration TWA8 for cobalt and chromium in all plants exceeded occupational exposure prescribed values. However, the nickel found did not exceed the prescribed values in all the plants except for NIOSH RELs.

Environmental assessment of a watertube boiler firing a coal-water slurry. Volume 1. Technical results. Final report, January 1984-March 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeRosier, R.; Waterland, L.R.

1986-02-01

The report describes results from field testing a watertube industrial boiler firing a coal/water slurry (CWS) containing about 60% coal. Emission measurements included continuous monitoring of flue-gas emissions; source assessment sampling system (SASS) sampling of the flue-gas, with subsequent analysis of samples to obtain total flue-gas organics in two boiling point ranges, compound category information within these ranges, specific quantitation of the semivolatile organic priority pollutants, and flue-gas concentrations of 73 trace elements: EPA Methods 5/8 sampling for particulate, SO/sub 2/, and SO/sub 3/ emissions; and grab sampling of fuel and ash for inorganic composition. NOx, SO/sub 2/, CO, andmore » TUHC emissions were in the 230-310, 880-960, 170-200, and 1-3 ppm ranges (corrected to 3% 02), respectively, over the two tests performed. Particulate levels at the boiler outlet (upstream of the unit's baghouse) were 7.3 g/dscm in the comprehensive test. Coarse particulate (>3 micrometers) predominated. Total organic emissions were almost 50 mg/dscm, with about 70% of the organic matter in the nonvolatile (>300 C) boiling point range. The bottom ash organic content was 8 mg/g, 80% of which was in the nonvolatile range. Of the PAHs, only naphthalene was detected in the flue gas particulate, with emission levels of 8.6 micrograms/dscm. Several PAHs were found in the bottom ash.« less

Emission of polycyclic aromatic hydrocarbons and lead during Chinese mid-autumn festival.

PubMed

Kuo, Chung-Yih; Lee, Hong-Shen; Lai, Jeang-Hung

2006-07-31

The emission factors of total particulate polycyclic aromatic hydrocarbons (PAHs), Benzo(a)pyrene (BaP), BaP-equivalent doses (BaP(eq)) and Pb for burning three kinds of charcoal were investigated in this study: fast-lighting charcoal, Taiwanese, and Indonesian charcoal (the latter two of which are not fast-lighting). Compared to the burning of Taiwanese and Indonesian charcoal, the burning of fast-lighting charcoal can emit much larger amounts of total PAHs, BaP(eq) and Pb into the atmosphere. The emission factors of total PAHs, BaP and BaP(eq) for broiling meat were noticeably higher than those for broiling vegetables and non-fish seafood. When using Indonesian charcoal to broil meat, the total emission factors of particulate PAHs and BaP were about 15.7 and 0.39 mg/kg, respectively. The total amounts of particulate PAHs and Pb emitted from cookouts during Mid-Autumn Festival were 2881 and 120 g, respectively. Total PAHs and BaP(eq) in PM(10) aerosols on Mid-Autumn Festival nights increased about 1.6 and 1.5 times, respectively, higher than those on non-festival nights. The mean concentration of Pb on the nights of Mid-Autumn Festival increases to about 2.8 times that of non-festival nights.

[Size distribution characteristics of particulate matter in the top areas of coke oven].

PubMed

Xie, Qiuyan; Zhao, Hongwei; Yu, Tao; Ning, Zhaojun; Li, Jinmu; Niu, Yong; Zheng, Yuxin; Zhao, Xiulan; Duan, Huawei

2015-03-01

To systematically evaluate the environmental exposure information of coke oven workers, we investigated the concentration and size distribution characteristics of the particle matter (PM) in the top working area of coke oven. The aerodynamic particle sizer spectrometer was employed to collect the concentration and size distribution information of PM at a top working area. The PM was divided into PM ≤ 1.0 µm, 1.0 µm < PM ≤ 2.5 µm, 2.5 µm < PM ≤ 5.0 µm, 5.0 µm < PM ≤ 10.0 µm and PM>10.0 µm based on their aerodynamic diameters. The number concentration, surface area concentration, and mass concentration were analyzed between different groups. We also conducted the correlation analysis on these parameters among groups. We found the number and surface area concentration of top area particulate was negatively correlated with particle size, but mass concentration curve showed bimodal type with higher point at PM = 1.0 µm and PM = 5.0 µm. The average number concentration of total particulate matter in the top working area was 661.27 number/cm³, surface area concentration was 523.92 µm²/cm³, and mass concentration was 0.12 mg/m³. The most number of particulate matter is not more than 1 µm (PM(1.0)), and its number concentration and surface area concentration accounted for 96.85% and 67.01% of the total particles respectively. In the correlation analysis, different particle size correlated with the total particulate matter differently. And the characteristic parameters of PM2.5 cannot fully reflect the total information of particles. The main particulate matter pollutants in the top working area of coke oven is PM1.0, and it with PM(5.0) can account for a large proportion in the mass concentration of PM. It suggest that PM1.0 and PM(5.0) should be considered for occupational health surveillance on the particulate matter in the top area of coke oven.

Temporal variability and spatial distribution of suspended matter and organic C pool in the Zambezi River

NASA Astrophysics Data System (ADS)

Teodoru, Cristian R.; Bouillon, Steven; Borges, Alberto V.; Darchambeau, François; Nyoni, Frank C.; Nyambe, Imasiku

2014-05-01

It is increasingly recognized that rivers are active components of global carbon (C) cycling, able of processing, emitting into atmosphere, and transporting to the oceans large quantities of both organic and inorganic carbon derived from the surrounding terrestrial landscape. Although tropical rivers contribute with more than half to the global freshwater discharge to the oceans, there is surprisingly little information on biogeochemistry and C cycling of those systems, especially for Africa. As part of a broader study on the biogeochemistry of large African river basins, we present here data on temporal and spatial variability of total suspended matter (TSM), particulate (POC) and dissolved organic C (DOC) in the Zambezi River (length = 2900 km, catchment area > 1.4 million km2, annual discharge ~ 4150 m3/s) in relation to physico-chemical proprieties (conductivity, oxygen, pH, total alkalinity), bacterial respiration, primary production and net aquatic metabolism. Data were collected along the entire river stretch during 2012 and 2013, and over 2 climatic (dry and wet) seasons to constrain the interannual variability, seasonality and spatial heterogeneity of the investigated parameters, and at two monitoring stations: one on the Zambezi mainstream, and one on the Kafue River (major tributary of the Zambezi; total length ~ 1900 km, catchment ~ 156, 000 km2, annual discharge = 350 m3/s), both located several km upstream their confluence. During the two sampled years, TSM concentrations varied from 1.6 mg/L to 110 mg/L (mean 17 in 2012 and 29 mg/L in 2013) and were systematically higher in the river mainstream (mean 21 mg/L and 36 mg/L in 2012 and 2013, respectively) compared to both reservoirs (the Kariba and the Cahora Bassa) where TSM concentrations average 2.5 mg/L. Despite the disturbance along the aquatic continuum caused by the presence of the two man-made reservoirs, a distinct longitudinal pattern was observed during both years, with TSM increasing downstream, and pH, conductivity and total alkalinity decreasing gradually. A good and negative correlation exists between the relative contribution of both POC and particulate nitrogen (PN) and the total suspended load (higher organic fraction in low suspended load) accounting for approximately 13% and 1.5%, respectively, of the TSM. Higher contribution of both POC and PN was observed systematically in reservoirs (30% and 4%, respectively), which together with the isotopic signature (δ13C-POC of -28.3 o and δ15N-P of 0.8) suggests the dominance of aquatic produced organic matter in reservoirs compared to the river mainstream (8% and 1%, respectively) of mostly terrestrial origin (δ13C-POC: -25o and δ15N-PN: 2.8). Less clear distinction between mainstream river (3.2 mg/L) and reservoir (2.5 mg/L) was observed for DOC (mean 3.1 mg/L) which showed generally an increasing trend downstream. The comparison between the two monitoring stations indicate an overall higher sediment load in the Kafue River (21 mg/L) compared to the Zambezi (7 mg/L), but lower contribution of particulate organic fraction (9% POC and 1% PN, respectively) and higher DOC (4.2 mg/L) versus 17% POC, 2.5% PN and 2.5mg/L DOC in the Zambezi.

Magnetic properties and heavy metal contents of automobile emission particulates*

PubMed Central

Lu, Sheng-gao; Bai, Shi-qiang; Cai, Jing-bo; Xu, Chang

2005-01-01

Measurements of the magnetic properties and total contents of Cu, Cd, Pb and Fe in 30 automobile emission particulate samples indicated the presence of magnetic particles in them. The values of frequency dependent susceptibility (χ fd) showed the absence of superparamagnetic (SP) grains in the samples. The IRM20 mT (isothermal remanent magnetization at 20 mT) being linearly proportional to SIRM (saturation isothermal remanent magnetization) (R 2=0.901), suggested that ferrimagnetic minerals were responsible for the magnetic properties of automobile emission particulates. The average contents of Cu, Cd, Pb and Fe in automobile emission particulates were 95.83, 22.14, 30.58 and 34727.31 mg/kg, respectively. Significant positive correlations exist between the magnetic parameters and the contents of Pb, Cu and Fe. The magnetic parameters of automobile emission particulates reflecting concentration of magnetic particles increased linearly with increase of Pb and Cu content, showed that the magnetic measurement could be used as a preliminary index for detection of Pb and Cu pollution. PMID:16052705

Formation of Particulate Matter from the Oxidation of Evaporated Wastewater from Hydraulic Fracturing Activity

NASA Astrophysics Data System (ADS)

Hildebrandt Ruiz, L.; Bean, J. K.; Bilotto, A.

2017-12-01

The use of hydraulic fracturing for production of petroleum and natural gas has increased dramatically in the last decade, but the environmental impacts of this technology remain unclear. Experiments were conducted to quantify airborne emissions from twelve samples of hydraulic fracturing flowback wastewater collected in the Permian Basin, as well as the photochemical processing of these emissions leading to the formation of particulate matter. The concentration of total volatile carbon (TVC, hydrocarbons evaporating at room temperature) averaged 29 milligrams of carbon per liter (mgC/L) and the TVC evaporation rate averaged 1357 mgC/L-m2-min. After photochemical oxidation under high NOx conditions the amount of organic particulate matter formed per milliliter of wastewater evaporated averaged 24 micrograms (µg); the amount of ammonium nitrate formed averaged 262 µg. In the state of Texas, the potential formation of PM from evaporated flowback wastewater is similar to the estimated PM emissions from diesel engines used in oil rigs, emphasizing the need to quantify wastewater evaporation and atmospheric processing of these emissions.

[Impact of atmospheric total suspended particulate pollution on photosynthetic parameters of street mango trees in Xiamen City].

PubMed

Yu, Yu-xian; Chen, Jin-sheng; Ren, Yin; Li, Fang-yi; Cui, Sheng-hui

2010-05-01

With the development of urbanization, total suspended particulate (TSP) pollution is getting serious, and the normal physiological processes of urban vegetation are profoundly affected while adsorbing and purifying the particulates. In this study, four areas were selected, i.e., Tingxi reservoir (clean control area), Xiamen University (cultural and educational area), Xianyue (business area), and Haicang (industrial area), with their atmospheric TSP concentrations and the photosynthetic parameters of street Mango (Mangifera indica) trees monitored in April and May, 2009. The daily average concentration of TSP in Tingxi, Xiamen University, Xianyue, and Haicang was 0.061, 0.113, 0.120 and 0.205 mg x m(-3), respectively, and the impact of TSP stress on M. indica was in the sequence of Haicang > Xianyue > Xiamen University > Tingxi. TSP pollution negatively affected the net photosynthetic rate, stomatal conductance, and transpiration rate of M. indica, and induced intercellular CO2 concentration changed significantly. High TSP concentration could cause the decline of net photosynthetic rate via stomatal limitation.

Manganese and welding fume exposure and control in construction.

PubMed

Meeker, John D; Susi, Pam; Flynn, Michael R

2007-12-01

Overexposure to welding fume constituents, particularly manganese, is of concern in the construction industry due to the prevalence of welding and the scarcity of engineering controls. The control effectiveness of a commercially available portable local exhaust ventilation (LEV) unit was assessed. It consisted of a portable vacuum and a small bell-shaped hood connected by a flexible 2 inch (50.8 mm) diameter hose, in both experimental and field settings. The experimental testing was done in a semienclosed booth at a pipefitter training facility. Five paired trials of LEV control vs. no control, each approximately 1 hr in duration and conducted during two successive welds of 6 inch (152.4 mm) diameter carbon steel pipe were run in random order. Breathing zone samples were collected outside the welding hood during each trial. In the field scenario, full-shift breathing zone samples were collected from two pipefitters welding carbon steel pipe for a chiller installation on a commercial construction project. Eight days of full-shift sampling were conducted on both workers (n = 16), and the LEV was used by one of the two workers on an alternating basis for 7 of the days. All samples were collected with personal sample pumps calibrated at 2 L/min. Filter cassettes were analyzed for total particulate and manganese concentration by a certified laboratory. In the experimental setting, use of the portable LEV resulted in a 75% reduction in manganese exposure (mean 13 microg/m(3) vs. 51 microg/m(3); p < 0.05) and a 60% reduction in total particulate (mean 0.74 mg/m(3) vs. 1.83 mg/m(3); p < 0.05). In the field setting, LEV use resulted in a 53% reduction in manganese exposure (geometric mean 46 microg/m(3) vs. 97 microg/m(3); p < 0.05) but only a 10% reduction in total particulate (geometric mean 4.5 mg/m(3) vs. 5.0 mg/m(3); p > 0.05). These results demonstrate that LEV use can reduce manganese exposure associated with welding tasks in construction.

Phosphorus transport pathways to streams in tile-drained agricultural watersheds.

PubMed

Gentry, L E; David, M B; Royer, T V; Mitchell, C A; Starks, K M

2007-01-01

Agriculture is a major nonpoint source of phosphorus (P) in the Midwest, but how surface runoff and tile drainage interact to affect temporal concentrations and fluxes of both dissolved and particulate P remains unclear. Our objective was to determine the dominant form of P in streams (dissolved or particulate) and identify the mode of transport of this P from fields to streams in tile-drained agricultural watersheds. We measured dissolved reactive P (DRP) and total P (TP) concentrations and loads in stream and tile water in the upper reaches of three watersheds in east-central Illinois (Embarras River, Lake Fork of the Kaskaskia River, and Big Ditch of the Sangamon River). For all 16 water year by watershed combinations examined, annual flow-weighted mean TP concentrations were >0.1 mg L(-1), and seven water year by watershed combinations exceeded 0.2 mg L(-1). Concentrations of DRP and particulate P (PP) increased with stream discharge; however, particulate P was the dominant form during overland runoff events, which greatly affected annual TP loads. Concentrations of DRP and PP in tiles increased with discharge, indicating tiles were a source of P to streams. Across watersheds, the greatest DRP concentrations (as high as 1.25 mg L(-1)) were associated with a precipitation event that followed widespread application of P fertilizer on frozen soils. Although eliminating this practice would reduce the potential for overland runoff of P, soil erosion and tile drainage would continue to be important transport pathways of P to streams in east-central Illinois.

Major and trace element partitioning between dissolved and particulate phases in Antarctic surface snow.

PubMed

Grotti, M; Soggia, F; Ardini, F; Magi, E

2011-09-01

In order to provide a new insight into the Antarctic snow chemistry, partitioning of major and trace elements between dissolved and particulate (i.e. insoluble particles, >0.45 μm) phases have been investigated in a number of coastal and inland snow samples, along with their total and acid-dissolvable (0.5% nitric acid) concentrations. Alkaline and alkaline-earth elements (Na, K, Ca, Mg, Sr) were mainly present in the dissolved phase, while Fe and Al were predominantly associated with the particulate matter, without any significant difference between inland and coastal samples. On the other hand, partitioning of trace elements depended on the sampling site position, showing a general decrease of the particulate fraction by moving from the coast to the plateau. Cd, Cu, Pb and Zn were for the most part in the dissolved phase, while Cr was mainly associated with the particulate fraction. Co, Mn and V were equally distributed between dissolved and particulate phases in the samples collected from the plateau and preferentially associated with the particulate in the coastal samples. The correlation between the elements and the inter-sample variability of their concentration significantly decreased for the plateau samples compared to the coastal ones, according to a change in the relative contribution of the metal sources and in good agreement with the estimated marine and crustal enrichment factors. In addition, samples from the plateau were characterised by higher enrichment factors of anthropogenic elements (Cd, Cr, Cu, Pb and Zn), compared to the coastal area. Finally, it was observed that the acid-dissolvable metal concentrations were generally lower than the total concentration values, showing that the acid treatment can dissolve only a given fraction of the metal associated with the particulate (<20% for iron and aluminium).

[Distribution and source of particulate organic carbon and particulate nitrogen in the Yangtze River Estuary in summer 2012].

PubMed

Xing, Jian-Wei; Xian, Wei-Wei; Sheng, Xiu-Zhen

2014-07-01

Based on the data from the cruise carried out in August 2012 in the Yangtze River Estuary and its adjacent waters, spatial distributions of particulate organic carbon (POC), particulate nitrogen (PN) and their relationships with environmental factors were studied, and the source of POC and the contribution of phytoplankton to POC were analyzed combined with n (C)/n (N) ratio and chlorophyll a (Chl a) in the Yangtze River Estuary in summer 2012. The results showed that the concentrations of POC in the Yangtze River Estuary ranged from 0.68 mg x L(-1) to 34.80 mg x L(-1) in summer and the average content was 3.74 mg x L(-1), and PN contents varied between 0.03 mg x L(-1) and 9.13 mg x L(-1) with an average value of 0.57 mg x L(-1). Both of them presented that the concentrations in bottom layers were higher than those in the surface. POC and PN as well as total suspended matter (TSM) showed a extremel similar horizontal distribution trend that the highest values appeared in the near of the mouth and southwest of the survey waters, and decreased rapidly as toward the open seas, both of them showed higher contents in coastal zones and lower in outer sea. There was a fairly good positive linear relationship between POC and PN, which indicated that they had the same source. POC and PN expressed significantly positive correlations with TSM and chemical oxygen demand (COD), but showed relatively weak correlations with salinit and chlorophyll a, which demonstrated that terrestrial inputs had a strong influence on the distribution of POC and PN, and phytoplankton production was not the major source of organic matters in the Yangtze River Estuary. Both the n (C)/n (N) ratio and POC/Chl a analysis showed that the main source of POC was terrestrial inputs, and organic debris was the main existence form of POC. Quantitative analysis showed the biomass of phytoplankton only made an average of 2.54% contribution to POC in the Yangtze Rive Estuary in summer and non-living POC occupied the overwhelming advantage.

Mineralogy and geochemistry of atmospheric particulates in western Iran

NASA Astrophysics Data System (ADS)

Ahmady-Birgani, Hesam; Mirnejad, Hassan; Feiznia, Sadat; McQueen, Ken G.

2015-10-01

This study investigates the mineralogy and physico-chemical properties of atmospheric particulates collected at Abadan (southwestern Iran) near the Persian Gulf coast and Urmia (northwestern Iran) during ambient and dust events over 6 months (winter 2011; spring 2012). Particle sizes collected were: TSP (total suspended particulates); PM10 (particulates <10 μm); and PM2.5 (particulates <2.5 μm). Minerals were identified using X-ray diffraction (XRD); particle morphology and composition were examined by scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM-EDX). Major minerals detected are calcite, quartz, clay minerals and gypsum, with relative abundance related to sampling site, collection period, wind direction, sampling head, and total sample amount. The anomalously high calcite content appears a characteristic feature originated from calcareous soils of the region. SEM observations indicated a wide range of particle morphologies over the 1-50 μm size range, with spherical, platy, cubic, elongate and prismatic shapes and rounding from angular to rounded. Energy dispersive X-ray analysis of TSP samples from both sites for non-dusty periods indicated that the sampled mineral suite contained Al, Mg, Na, Cl, P, S, Ca, K, Fe, Ti, and Si, mostly reflecting calcite, quartz, aluminosilicates, clays, gypsum and halite. Additionally, As, Pb, Zn, Mn, Sc, Nd, W, Ce, La, Ba and Ni were detected in TSP, PM10 and PM2.5 samples collected during dust events.

Size distributions of ambient air particles and enrichment factor analyses of metallic elements at Taichung Harbor near the Taiwan Strait

NASA Astrophysics Data System (ADS)

Fang, Guor-Cheng; Wu, Yuh-Shen; Chang, Shih-Yu; Huang, Shih-Han; Rau, Jui-Yeh

2006-10-01

This work attempts to characterize metallic elements associated with atmospheric particulate matter on a dry deposition plate, a TE-PUF high-volume air sampler and a universal air sampler. Dry deposition fluxes of particulates and concentrations of total suspended particulate, fine (PM 2.5) and coarse (PM 2.5-10) particulate matters were collected at Taichung harbor sampling sites from August 2004 to January 2005. Chemical analyses of metallic elements were made using a flame atomic absorption spectrophotometer coupled with hollow cathode lamps. Concentrations of metal elements in the forms of coarse particles and fine particles as well as the coarse/fine particulate ratios were presented. Statistical methods such as correlation analysis, principal component analysis and enrichment factor analysis were performed to compare the chemical components and identify possible emission sources at the sampling sites. Metallic elements of Cu, Zn, Pb, Cr, Ni and Mg had higher EF crust ratios in winter and spring than in summer and autumn. Diurnal and nocturnal variations of metallic element concentrations in fine and coarse particles were also discussed.

Remedial Investigation/Feasibility Study Fort Dix U.S. Army Installation Fort Dix, New Jersey

DTIC Science & Technology

1994-01-01

METHOD: PARTICULATE FILTER; GRAVIMETRIC: (NIOSH VOL. Ill I 8583 , NUISANCE DUST (TOTAL)). »OSHA REVOKED THE FINAL RULE LIMITS OF JANUARY 19, 1989 IN...VJ ISO .- i-.i^ !...= : \\J~::— :!__’ii!-!lS . l~>.-- -.^ - ORAL-MCUSE LD50i 5SS0 MO/KG ORAL-rAf-iivifcii i LD50: 750 MG

[Effect of humidity and temperature on filter and gravimetric measurement of ambient particulate matter in a balance room].

PubMed

Su, Wen-jin; Wang, Li-min; Weng, Shao-fan; Wang, Hai-jiao; Du, Li-li; Liu, Yue-wei; Yang, Lei; Chen, Wei-hong

2008-04-01

To assess the effects of the alteration of humidity and (or) temperature on weight of filters without and with ambient particulate matter in a balance room. The mass of blank dust sampling filters were weighed under (18 +/- 1) degrees C and (28 +/- 1) degrees C respectively, with the humidity varying from 35% relative humidity (RH) to 100% RH in a balance room. Then the blank filters were divided into two groups and were used to sample total dust and respirable dust. After sampling, the loaded filters were re-weighed under above conditions and the mass difference before and after the sampling were compared and analyzed. The vibration of the average mass of filters varied from 0.10 to 0.13 mg and from 0.06 to 0.09 mg under the temperatures of (18 +/- 1) degrees C and (28 +/- 1) degrees C respectively; When both the temperature and humidity changed, it varied from 0.12 to 0.16 mg. The deviation of average mass difference ranged from 0.07 to 0.10 mg and from 0.04 to 0.08 mg under the two temperatures mentioned above; When both the temperature and humidity changed, it varied from 0.09 to 0.14 mg. The average mass of blank filters and loaded filters were all positively correlated with the change of humidity (P < 0.01). No effects of humidity on the average mass difference of the loaded filters were observed. The average mass differences of loaded filters and blank filters under (18 +/- 1) degrees C were significantly higher than that under (28 +/- 1) degrees C (P < 0.01) when humidity was not changed. The alteration of humidity and (or) temperature in a balance room attributes to the deviation of the measurement of the mass of filters and thus affects the gravimetric measurements of ambient particulate matter.

Depositional characteristics of atmospheric polybrominated diphenyl ethers on tree barks

PubMed Central

Chun, Man Young

2014-01-01

Objectives This study was conducted to determine the depositional characteristics of several tree barks, including Ginkgo (Ginkgo biloba), Pine (Pinus densiflora), Platanus (Platanus), and Metasequoia (Metasequoia glyptostroboides). These were used as passive air sampler (PAS) of atmospheric polybrominated diphenyl ethers (PBDEs). Methods Tree barks were sampled from the same site. PBDEs were analyzed by highresolution gas chromatography/high-resolution mass spectrometer, and the lipid content was measured using the gravimetric method by n-hexane extraction. Results Gingko contained the highest lipid content (7.82 mg/g dry), whereas pine (4.85 mg/g dry), Platanus (3.61 mg/g dry), and Metasequoia (0.97 mg/g dry) had relatively lower content. The highest total PBDEs concentration was observed in Metasequoia (83,159.0 pg/g dry), followed by Ginkgo (53,538.4 pg/g dry), Pine (20,266.4 pg/g dry), and Platanus (12,572.0 pg/g dry). There were poor correlations between lipid content and total PBDE concentrations in tree barks (R2=0.1011, p =0.682). Among the PBDE congeners, BDE 206, 207 and 209 were highly brominated PBDEs that are sorbed to particulates in ambient air, which accounted for 90.5% (84.3-95.6%) of the concentration and were therefore identified as the main PBDE congener. The concentrations of particulate PBDEs deposited on tree barks were dependent on morphological characteristics such as surface area or roughness of barks. Conclusions Therefore, when using the tree barks as the PAS of the atmospheric PBDEs, samples belonging to same tree species should be collected to reduce errors and to obtain reliable data. PMID:25116365

Depositional characteristics of atmospheric polybrominated diphenyl ethers on tree barks.

PubMed

Chun, Man Young

2014-07-17

This study was conducted to determine the depositional characteristics of several tree barks, including Ginkgo (Ginkgo biloba), Pine (Pinus densiflora), Platanus (Platanus), and Metasequoia (Metasequoia glyptostroboides). These were used as passive air sampler (PAS) of atmospheric polybrominated diphenyl ethers (PBDEs). Tree barks were sampled from the same site. PBDEs were analyzed by highresolution gas chromatography/high-resolution mass spectrometer, and the lipid content was measured using the gravimetric method by n-hexane extraction. Gingko contained the highest lipid content (7.82 mg/g dry), whereas pine (4.85 mg/g dry), Platanus (3.61 mg/g dry), and Metasequoia (0.97 mg/g dry) had relatively lower content. The highest total PBDEs concentration was observed in Metasequoia (83,159.0 pg/g dry), followed by Ginkgo (53,538.4 pg/g dry), Pine (20,266.4 pg/g dry), and Platanus (12,572.0 pg/g dry). There were poor correlations between lipid content and total PBDE concentrations in tree barks (R(2)=0.1011, p =0.682). Among the PBDE congeners, BDE 206, 207 and 209 were highly brominated PBDEs that are sorbed to particulates in ambient air, which accounted for 90.5% (84.3-95.6%) of the concentration and were therefore identified as the main PBDE congener. The concentrations of particulate PBDEs deposited on tree barks were dependent on morphological characteristics such as surface area or roughness of barks. Therefore, when using the tree barks as the PAS of the atmospheric PBDEs, samples belonging to same tree species should be collected to reduce errors and to obtain reliable data.

Characterization of lubrication oil emissions from aircraft engines.

PubMed

Yu, Zhenhong; Liscinsky, David S; Winstead, Edward L; True, Bruce S; Timko, Michael T; Bhargava, Anuj; Herndon, Scott C; Miake-Lye, Richard C; Anderson, Bruce E

2010-12-15

In this first ever study, particulate matter (PM) emitted from the lubrication system overboard breather vent for two different models of aircraft engines has been systematically characterized. Lubrication oil was confirmed as the predominant component of the emitted particulate matter based upon the characteristic mass spectrum of the pure oil. Total particulate mass and size distributions of the emitted oil are also investigated by several high-sensitivity aerosol characterization instruments. The emission index (EI) of lubrication oil at engine idle is in the range of 2-12 mg kg(-1) and increases with engine power. The chemical composition of the oil droplets is essentially independent of engine thrust, suggesting that engine oil does not undergo thermally driven chemical transformations during the ∼4 h test window. Volumetric mean diameter is around 250-350 nm for all engine power conditions with a slight power dependence.

Improving properties of Mg with Al–Cu additions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rashad, Muhammad, E-mail: rashadphy87@gmail.com; National Engineering Research Center for Magnesium Alloys, Chongqing University, Chongqing 400044; Pan, Fusheng, E-mail: fspan@cqu.edu.cn

The present work reports improvement in tensile properties of the Mg matrix reinforced with micron-sized copper–aluminum particulate hybrids. The Al–Cu particulate hybrids were incorporated into the Mg matrix through powder metallurgy method. The synthesized alloys exhibited homogeneously dispersed Mg{sub 2}Cu particles in the matrix, therefore leading to a 110% increase in yield strength (221 MPa) and a 72% enhancement in ultimate tensile strength (284 MPa) by addition of 1.0 wt.%Al–0.6 wt.%Cu particle hybrids. Optical microscopy, scanning election microscopy, transmission electron microscopy and X-ray diffraction were used to investigate the microstructure and intermetallic phases of the synthesized alloys. - Highlights: •more » Mg matrix is reinforced with Al–Cu particulate hybrids. • Powder metallurgic method is used to fabricate the alloys. • Tensile strength and ductility were increased simultaneously.« less

Characterization of engineered nanoparticles in commercially available spray disinfectant products advertised to contain colloidal silver.

PubMed

Rogers, Kim R; Navratilova, Jana; Stefaniak, Aleksandr; Bowers, Lauren; Knepp, Alycia K; Al-Abed, Souhail R; Potter, Phillip; Gitipour, Alireza; Radwan, Islam; Nelson, Clay; Bradham, Karen D

2018-04-01

Given the potential for human exposure to silver nanoparticles from spray disinfectants and dietary supplements, we characterized the silver-containing nanoparticles in 22 commercial products that advertised the use of silver or colloidal silver as the active ingredient. Characterization parameters included: total silver, fractionated silver (particulate and dissolved), primary particle size distribution, hydrodynamic diameter, particle number, and plasmon resonance absorbance. A high degree of variability between claimed and measured values for total silver was observed. Only 7 of the products showed total silver concentrations within 20% of their nominally reported values. In addition, significant variations in the relative percentages of particulate vs. soluble silver were also measured in many of these products reporting to be colloidal. Primary silver particle size distributions by transmission electron microscopy (TEM) showed two populations of particles - smaller particles (<5nm) and larger particles between 20 and 40nm. Hydrodynamic diameter measurements using nanoparticle tracking analysis (NTA) correlated well with TEM analysis for the larger particles. Z-average (Z-Avg) values measured using dynamic light scattering (DLS); however, were typically larger than both NTA or TEM particle diameters. Plasmon resonance absorbance signatures (peak absorbance at around 400nm indicative of metallic silver nanoparticles) were only noted in 4 of the 9 yellow-brown colored suspensions. Although the total silver concentrations were variable among products, ranging from 0.54mg/L to 960mg/L, silver containing nanoparticles were identified in all of the product suspensions by TEM. Published by Elsevier B.V.

Characteristics of particulate-bound polycyclic aromatic hydrocarbons emitted from industrial grade biomass boilers.

PubMed

Yang, Xiaoyang; Geng, Chunmei; Sun, Xuesong; Yang, Wen; Wang, Xinhua; Chen, Jianhua

2016-02-01

Polycyclic aromatic hydrocarbons (PAHs) are carcinogenic or mutagenic and are important toxic pollutants in the flue gas of boilers. Two industrial grade biomass boilers were selected to investigate the characteristics of particulate-bound PAHs: one biomass boiler retro-fitted from an oil boiler (BB1) and one specially designed (BB2) biomass boiler. One coal-fired boiler was also selected for comparison. By using a dilution tunnel system, particulate samples from boilers were collected and 10 PAH species were analyzed by gas chromatography-mass spectrometry (GC-MS). The total emission factors (EFs) of PAHs ranged from 0.0064 to 0.0380 mg/kg, with an average of 0.0225 mg/kg, for the biomass boiler emission samples. The total PAH EFs for the tested coal-fired boiler were 1.8 times lower than the average value of the biomass boilers. The PAH diagnostic ratios for wood pellets and straw pellets were similar. The ratio of indeno(1,2,3-cd)pyrene/[indeno(1,2,3-cd)pyrene+benzo(g,h,i)perylene] for the two biomass boilers was lower than those of the reference data for other burning devices, which can probably be used as an indicator to distinguish the emission of biomass boilers from that of industrial coal-fired boilers and residential stoves. The toxic potential of the emission from wood pellet burning was higher than that from straw pellet burning, however both of them were much lower than residential stove exhausts. Copyright © 2015. Published by Elsevier B.V.

Occurrence and behaviour of dissolved, nano-particulate and micro-particulate iron in waste waters and treatment systems: new insights from electrochemical analysis.

PubMed

Matthies, R; Aplin, A C; Horrocks, B R; Mudashiru, L K

2012-04-01

Cyclic-, Differential Pulse- and Steady-state Microdisc Voltammetry (CV, DPV, SMV) techniques have been used to quantify the occurrence and fate of dissolved Fe(ii)/Fe(iii), nano-particulate and micro-particulate iron over a 12 month period in a series of net-acidic and net-alkaline coal mine drainages and passive treatment systems. Total iron in the mine waters is typically 10-100 mg L(-1), with values up to 2100 mg L(-1). Between 30 and 80% of the total iron occurs as solid phase, of which 20 to 80% is nano-particulate. Nano-particulate iron comprises 20 to 70% of the nominally "dissolved" (i.e. <0.45 μm) iron. Since coagulation and sedimentation are the only processes required to remove solid phase iron, these data have important implications for the generation or consumption of acidity during water treatment. In most waters, the majority of truly dissolved iron occurs as Fe(ii) (average 64 ± 22%). Activities of Fe(ii) do not correlate with pH and geochemical modelling shows that no Fe(ii) mineral is supersaturated. Removal of Fe(ii) must proceed via oxidation and hydrolysis. Except in waters with pH < 4.4, activities of Fe(iii) are strongly and negatively correlated with pH. Geochemical modelling suggests that the activity of Fe(iii) is controlled by the solubility of hydrous ferric oxides and oxyhydroxysulfates, supported by scanning and transmission electron microscopic analysis of solids. Nevertheless, the waters are generally supersaturated with respect to ferrihydrite and schwertmannite, and are not at redox equilibrium, indicating the key role of oxidation and hydrolysis kinetics on water treatment. Typically 70-100% of iron is retained in the treatment systems. Oxidation, hydrolysis, precipitation, coagulation and sedimentation occur in all treatment systems and - independent of water chemistry and the type of treatment system - hydroxides and oxyhydroxysulfates are the main iron sinks. The electrochemical data thus reveal the rationale for incomplete iron retention in individual systems and can thus inform future design criteria. The successful application of this low cost and rapid electrochemical method demonstrates its significant potential for real-time, on-site monitoring of iron-enriched waters and may in future substitute traditional analytical methods.

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

Mechanical properties of particulate composites based on a body-centered-cubic Mg-Li alloy containing boron

NASA Technical Reports Server (NTRS)

Whalen, R. T.; Gonzalez-Doncel, G.; Robinson, S. L.; Sherby, O. D.

1989-01-01

The effect of substituting the Mg metal in Mg-B composites by a Mg-14 wt pct Li solid solution on the ductility of the resulting composite was investigated using elastic modulus measurements on the P/M composite material prepared with a dispersion of B particles (in a vol pct range of 0-30) in a matrix of Mg-14 wt pct Li-1.5 wt pct Al. It was found that the elastic modulus of the composites increased rapidly with increasing boron, with specific stiffness values reaching about two times that of most structural materials. The values of the compression and tensile strengths increased significantly with boron additions. Good tensile ductility was achieved at the level of 10 vol pct B. However, at 20 vol pct B, the Mg-Li composite exhibited only limited tensile ductility (about 2 percent total elongation).

Deep-sea fluxes of barium and lithogenic trace elements in the subtropical northeast Atlantic

NASA Astrophysics Data System (ADS)

Stern, Judith; Dellwig, Olaf; Waniek, Joanna J.

2017-04-01

Total particle flux, Barium and lithogenic trace element fluxes were measured at the mooring Kiel 276 (33°N, 22°W) in the deep-sea of the subtropical Northeast Atlantic. The particulate material was collected between 2002 and 2008 with a sediment trap in 2000 m depth and analyzed with ICP-OES/-MS to determine its geochemical composition. The particle flux is controlled by primary production, lithogenic particle inputs via atmospheric transport and the migration of the Azores Front. We used refractory trace elements (eg. Ti, Zr, and the rare earth elements) to demonstrate the changes in flux and composition of the material due to lithogenic inputs. Shortly after periods of high dust load and enhanced primary production an increase in lithogenic trace element fluxes occurred. Especially the formation of aggregates with biogenic matter seems to have a major impact on the downwards transport of lithogenic particles. The observation of particulate Ba is of great interest since it is known as a proxy for past and present primary production. Ba fluxes ranging between 0.02 mg m-2 d-1 and 1.21 mg m-2 d-1 with biogenic proportions up to 97%. The fluxes of particulate Barium in the water column are mainly attributed to the strength of primary production.

Carbon and nitrogen cycling in the Zhubi coral reef lagoon of the South China Sea as revealed by 210Po and 210Pb.

PubMed

Yang, W F; Huang, Y P; Chen, M; Qiu, Y S; Li, H B; Zhang, L

2011-05-01

The radionuclides (210)Po and (210)Pb were examined to trace the cycling of particulate organic carbon (POC) and particulate organic nitrogen (PON) in the Zhubi coral reef lagoon. The net export flux of POC to the open sea is 14 mg Cm(-2) d(-1). However, the net exchange of PON has not yet been observed. On average, the vertical export fluxes in the lagoon of POC and PON, as derived from (210)Po/(210)Pb disequilibria, are 43 mg Cm(-2) d(-1) and 13.8 mg Nm(-2) d(-1), respectively. The deficit of (210)Po relative to (210)Pb in particulate matter provides evidence for the degradation of particulate organic matter. According to the mass balance budgets, 310 mg Cm(-2) d(-1) and 121 mg Nm(-2) d(-1) were recycled into dissolved fractions. Based on a first-order kinetics model, the degradation rate constants of POC and PON are 0.28 and 0.30 m(-1), respectively. Thus, (210)Po and (210)Pb can quantify the cycling of carbon and nitrogen in this coral lagoon. Copyright © 2011 Elsevier Ltd. All rights reserved.

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

Particulate matter emissions, and metals and toxic elements in airborne particulates emitted from biomass combustion: The importance of biomass type and combustion conditions.

PubMed

Zosima, Angela T; Tsakanika, Lamprini-Areti V; Ochsenkühn-Petropoulou, Maria Th

2017-05-12

The aim of this study was to investigate the impact of biomass combustion with respect to burning conditions and fuel types on particulate matter emissions (PM 10 ) and their metals as well as toxic elements content. For this purpose, different lab scale burning conditions were tested (20 and 13% O 2 in the exhaust gas which simulate an incomplete and complete combustion respectively). Furthermore, two pellet stoves (8.5 and 10 kW) and one open fireplace were also tested. In all cases, 8 fuel types of biomass produced in Greece were used. Average PM 10 emissions ranged at laboratory-scale combustions from about 65 to 170 mg/m 3 with flow oxygen at 13% in the exhaust gas and from 85 to 220 mg/m 3 at 20% O 2 . At pellet stoves the emissions were found lower (35 -85 mg/m 3 ) than the open fireplace (105-195 mg/m 3 ). The maximum permitted particle emission limit is 150 mg/m 3 . Metals on the PM 10 filters were determined by several spectrometric techniques after appropriate digestion or acid leaching of the filters, and the results obtained by these two methods were compared. The concentration of PM 10 as well as the total concentration of the metals on the filters after the digestion procedure appeared higher at laboratory-scale combustions with flow oxygen at 20% in the exhaust gas and even higher at fireplace in comparison to laboratory-scale combustions with 13% O 2 and pellet stoves. Modern combustion appliances and appropriate types of biomass emit lower PM 10 emissions and lower concentration of metals than the traditional devices where incomplete combustion conditions are observed. Finally, a comparison with other studies was conducted resulting in similar results.

Control of denitrification in a septage-treating artificial wetland: the dual role of particulate organic carbon.

PubMed

Hamersley, M Robert; Howes, Brian L

2002-10-01

We examined the factors controlling organic carbon (C) cycling and its control of nitrogen (N) removal via denitrification in an aerated artificial wetland treating highly concentrated wastewater to nutrient-removal standards. Processing of organic material by the septage-treating wetland affected the biological reactivity (half-life, or t1/2) of organic C pools through microbial degradation and gravity fractionation of the influent septage. Primary sedimentation fractionated the initial septage material (t1/2 = 8.4d) into recalcitrant waste solids (t1/2 = 16.7d) and highly labile supernatant (t1/2 = 5.0d), allowing this reactive fraction to be further degraded during treatment in aerobic wetland tanks until a less labile material (t1/2 = 7.3d) remained. Organic C contributions from in situ fixation by nitrifying bacteria or algae in these tanks were small, about 1% of the C degradation rate. In the aerated tanks, denitrification was correlated with particulate organic C loading rates, although the average C required (0.35 mg C L(-1)h(-1)) to support denitrification was only 12% of the total C respiration rate (2.9 mg C L(-1)h(-1)). Additions of plant litter (2.5g C L(-1)) to the aerated tanks under normal operating conditions doubled denitrification rates to 0.58 mg N L(-1)h(-1), and reduced effluent nitrate levels by half, from 12.7 to 6.4 mg N L(-1). However, C degradation within the plant litter (0.15mg C L(-1)h(-1)) was sufficient to have accounted for only 35% of the additional denitrification. Evidence from laboratory and full-scale plant litter additions as well as process monitoring indicates that the stimulation of denitrification is due to the respiration-driven formation of anaerobic microsites within particulate organic C. In this aerated highly C-loaded septage-treating wetland, anaerobic microsite, rather than C substrate availability limits denitrification.

Development of a job-exposure matrix for exposure to total and fine particulate matter in the aluminum industry

PubMed Central

Noth, Elizabeth M.; Dixon-Ernst, Christine; Liu, Sa; Cantley, Linda; Tessier-Sherman, Baylah; Eisen, Ellen A.; Cullen, Mark R.; Hammond, S. Katharine

2014-01-01

Increasing evidence indicates that exposure to particulate matter (PM) at environmental concentrations increases the risk of cardiovascular disease, particularly PM with an aerodynamic diameter of less than 2.5μm (PM2.5). Despite this, the health impacts of higher occupational exposures to PM2.5 have rarely been evaluated. In part, this research gap derives from the absence of information on PM2.5 exposures in the workplace. To address this gap, we have developed a job-exposure matrix (JEM) to estimate exposure to two size fractions of PM in the aluminum industry. Measurements of total PM (TPM) and PM2.5 were used to develop exposure metrics for an epidemiologic study. TPM exposures for distinct exposure groups (DEGs) in the JEM were calculated using 8,385 personal TPM samples collected at 11 facilities (1980-2011). For 8 of these facilities, simultaneous PM2.5 and TPM personal monitoring was conducted from 2010-2011 to determine the percent of TPM that is composed of PM2.5 (%PM2.5) in each DEG. The mean TPM from the JEM was then multiplied by %PM2.5 to calculate PM2.5 exposure concentrations in each DEG. Exposures in the smelters were substantially higher than in fabrication units; mean TPM concentrations in smelters and fabrication facilities were 3.86 mg/m3 and 0.76 mg/m3, and the corresponding mean PM2.5 concentrations were 2.03 mg/m3 and 0.40 mg/m3. Observed occupational exposures in this study generally exceeded environmental PM2.5 concentrations by an order of magnitude. PMID:24022670

Emissions of particle-phase polycyclic aromatic hydrocarbons (PAHs) in the Fu Gui-shan Tunnel of Nanjing, China

NASA Astrophysics Data System (ADS)

Chen, Fei; Hu, Wei; Zhong, Qin

2013-04-01

Real-world vehicle emission factors for PM10 (particulate matter with aerodynamic diameter smaller than 10 μm) and particle-phase polycyclic aromatic hydrocarbons (PAHs) from mixed vehicles were quantified in the Fu Gui-shan Tunnel of Nanjing during summer and winter of 2010. Concentrations of PM10 and sixteen particle phase polycyclic aromatic hydrocarbons (PAHs) in the entrance and exit of the tunnel were studied. The results showed that the four most abundant particular phase polycyclic aromatic hydrocarbons (PAHs) of motor vehicle were benzo[ghi]perylene, benzo[k]fluoranthene, benz[a]anthracene and benzo[a]pyrene. The emission factors for PM10 and particle-phase PAHs were 687 mg veh- 1 km- 1 and 18.853 mg veh- 1 km- 1 in summer, 714 mg veh- 1 km- 1 and 20.374 mg veh- 1 km- 1 in winter. Higher particle-phase PAH emission factors were found to be associated with a high proportion of diesel-fueled vehicles (DV). The estimated PM10 emission factor of gasoline-fueled vehicles (GV) was 513 mg veh- 1 km- 1 and the value for DV was 914 mg veh- 1 km- 1, while EFDV of particulate PAH (31.290 mg veh- 1 km- 1) was nearly 4 times higher than EFGV (9.310 mg veh- 1 km- 1). The five highest emission factors of diesel-fueled vehicles (DV) were benzo[ghi]perylene, benzo[k]fluoranthene, Indeno[1,2,3-cd]pyrene, benz[a]anthracene and benzo[a]pyrene, which was similarly found in the gasoline-fueled vehicles (GV). The sum of these five emission factors accounted for ~ 69% of the total particle-phase PAH of DV and ~ 67% of GV.

Settling flux and origin of particulate organic carbon in a macro-tidal semi-enclosed embayment: Luoyuan Bay, Southeast China coast

NASA Astrophysics Data System (ADS)

Wang, Ai-jun; Ye, Xiang; Xu, Xiao-hui; Yin, Xi-jie; Xu, Yong-hang

2018-06-01

Coastal embayments play a vital role in the global carbon cycle either as sources of organic matter to open sea or as carbon sinks due to the accumulation of organic matter in sediments. This paper describes a study of Luoyuan Bay, a typical semi-enclosed embayment with a total area of approximately 227 km2 in a strong tidal environment. The analysed results indicate that the particulate organic carbon (POC) concentration in suspended particulate matter (SPM) varies from 0.57 mg/L to 1.33 mg/L at the bottom layer (0.5 MAB, meters above bed) and from 0.54 mg/L to 1.25 mg/L at the surface layer (0.5 MBS, meters below surface). The δ13C‰ ranges from -25.52‰ to -23.54‰ and exhibits different variations at the surface and bottom layers in spring and neap tides. The POC content in deposited particulate matter (DPM) varies from 0.62% to 2.95%, increasing from spring to neap tide, and the δ13C and C/N molar ratio are -25.29‰ ∼ -21.41‰ and 4.18-8.53, respectively. The settling fluxes of POC obtained by sediment trap decrease from 2.25 g/m2·tide during the spring tide to 0.55 g/m2·tide during the neap tide with a mean value of 1.41 g/m2·tide during the observation, whereas the settling flux of SPM decreases from 456.76 g/m2·tide during the spring tide to 37.12 g/m2·tide during the neap tide. Combining the δ13C and C/N molar ratio, three end-members are recognized, i.e., freshwater algae and phytoplankton, marine algae and phytoplankton, and kelp-derived detritus. The mean contribution to POC from these three sources is 57.2%, 31.8% and 11.0% in SPM, and 39.9%, 35.0% and 25.1% in DPM, respectively. The POC from freshwater algae, phytoplankton and kelp-derived detritus is controlled by sediment dynamic processes.

Toxicity of cadmium to goldfish, Carassius auratus, in hard, and soft water

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCarty, L.S.; Henry, J.A.C.; Houston, A.H.

1978-01-01

Variations in cadmium form and concentration and in selected water quality parameters (pH, dissolved oxygen, total hardness, total alkalinity, conductivity) were monitored during static bioassays conducted with relatively soft (approximately 20 mg/L as CaCO/sub 3/) and hard (approximately 140 mg/L as CaCO/sub 3/) waters. Cadmium concentrations were reasonably stable in soft water, and with the exception of total hardness, water quality was not greatly altered during assay. Cumulative mortality curves were of a simple sigmoidal type and readily analyzed by conventional procedures. LC50 values of 2.76, 2.13, and 1.78 mg Cd/L were estimated on the basis of 48-, 96-, andmore » 240-h periods of observation. During hard-water trials there were transient increases in the amount of particulate cadmium present and sharp decreases in total cadmium levels. Several parameters (pH, total alkalinity, conductivity) exhibited transient and/or sustained variations of a cadmium concentration-dependent type. Mortality curves were typically biphasic. The extent of first-phase mortality was significantly correlated with the magnitude of the initial pH decline and the amount of cadmium present in centrifugable form. Conventional procedures did not result in rectification of 240-h cumulative mortality curves, and the 240-h LC50 value (40.2 mg Cd/L) is considered to be inherently less precise than those obtained on the basis of 48- and 96-h periods of observation (46.9, 46.8 mg Cd/L).« less

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

The Influence of Wetland Cover and Dissolved Organic Carbon on Mercury Export in Forest Landscapes, Northeastern USA

NASA Astrophysics Data System (ADS)

Dittman, J. A.; Shanley, J. B.; Driscoll, C. T.; Aiken, G.; Chalmers, A.; Towse, J.

2007-12-01

Mercury (Hg) contamination is widespread in remote areas of the northeastern USA. Atmospheric Hg is deposited on terrestrial uplands and subsequently mobilized to downstream aquatic ecosystems. We are investigating the fate of Hg deposited in forested watersheds by quantifying stream transport of Hg, and the interactions with dissolved and particulate organic matter. We hypothesize that the landscape characteristics controlling the production and mobility of organic matter will likewise control the mobility of Hg. This research was conducted at three sites in the Northeast that represent a range of hydrochemical conditions and span a range of wetland cover. Most stream export of Hg occurs at high flow; therefore we collected samples during snowmelt and storms. Mercury concentrations increase with discharge at all three sites; however the partitioning of Hg fractions (dissolved vs. particulate) differs among sites during high flow events. At the Hubbard Brook Experimental Forest, NH (watershed 6), there are no true wetlands and dissolved organic carbon (DOC) and total Hg (THg) concentrations, and suspended sediment concentration (SSC) (mean DOC = 3.1 mg C L-1; THg = 1.5 ng L-1; SSC < 50 mg L-1) are low even during the highest of flow events. At Sleepers River, VT (watershed 9), SSC can be elevated during events (SSC > 500 mg L-1), consequently the particulate Hg fraction can range as high as 95% of the THg concentration (mean particulate Hg concentration = 10.2 ng L- 1). At Archer Creek (Huntington Forest, NY), which has the greatest percent wetland cover (10%) of our three sites, DOC concentrations are high (mean DOC = 7.5 mg C L-1), while SSC are low (SSC < 10 mg L- 1). At Archer Creek, Hg is largely in the dissolved form (~75% of Hg) and strongly correlated with DOC (r2 = 0.90). The hydrophobic organic acid (HPOA) fraction of DOC is most effective at mobilizing Hg and is strongly correlated to Hg concentrations in stream water. This research suggests that high concentrations of Hg can be present in stream water from forest watersheds during high flow events, and that wetlands and suspended sediment favor Hg export. However, it is not clear to what degree this Hg is bioavailable for potential uptake by organisms in aquatic ecosystems following mobilization.

Effects of polyacrylamide on soil erosion and nutrient losses from substrate material in steep rocky slope stabilization projects.

PubMed

Chen, Zhang; Chen, Wenlu; Li, Chengjun; Pu, Yanpin; Sun, Haifeng

2016-06-01

Erosion of denuded steep rocky slopes causes increasing losses of nitrogen and phosphorus, which is a severe problem in rocky slope protection. Thus, it is important to determine the appropriate materials that can reduce the erodibility and losses of nitrogen and phosphorus of the soil. In this paper, twenty-seven simulated rainfall events were carried out in a greenhouse, in which the substrate material was artificial soil; nine types of anionic polyacrylamide (PAM) were studied, which consisted of three molecular weight (6, 12, and 18 Mg mol(-1)) and three charge density (10, 20, and 30%) formulations in a 3 by 3 factorial design. The results showed that: (1) Polyacrylamide application reduced total nitrogen losses by 35.3% to 50.0% and total phosphorus losses by 34.9% to 48.0% relative to the control group. (2) The losses of total nitrogen and total phosphorus had significant correlation with the molecular weight. Besides, the losses of total phosphorus, particulate-bound phosphorus and inorganic nitrogen (NH4-N) were significantly correlated with their molecular weight and charge density. However, the losses of dissolved organic nitrogen, inorganic nitrogen (NO3-N), dissolved organic phosphorus, inorganic phosphorus (PO4-P) were non-significantly correlated with molecular weight and charge density. (3) Particulate-bound nitrogen and phosphorus were responsible for the losses of nitrogen and phosphorus during runoff events, where particulate-bound nitrogen made up 71.7% to 73.2% of total nitrogen losses, and particulate-bound phosphorus made up 82.3% to 85.2% of total phosphorus losses. (4) Polyacrylamide treatments increased water-stable aggregates content by 32.3% to 59.1%, total porosity by 11.3% to 49.0%, final infiltrative rate by 41.3% to 72.5%, and reduced soil erosion by 18.9% to 39.8% compared with the control group. Overall, the results of this study indicated that polyacrylamide application in the steep rocky slope stabilization projects could significantly reduce nutrient losses and soil erosion of substrate material. Copyright © 2016 Elsevier B.V. All rights reserved.

The Distribution between the Dissolved and the Particulate Forms of 49 Metals across the Tigris River, Baghdad, Iraq

PubMed Central

Hamad, Samera Hussein; Schauer, James Jay; Shafer, Martin Merrill; Abed Al-Raheem, Esam; Satar, Hyder

2012-01-01

The distribution of dissolved and particulate forms of 49 elements was investigated along transect of the Tigris River (one of the major rivers of the world) within Baghdad city and in its major tributary (Diyala River) from 11 to 28 July 2011. SF-ICP-MS was used to measure total and filterable elements at 17 locations along the Tigris River transect, two samples from the Diyala River, and in one sample from the confluence of the two rivers. The calculated particulate forms were used to determine the particle-partition coefficients of the metals. No major changes in the elements concentrations down the river transect. Dissolved phases dominated the physical speciation of many metals (e.g., As, Mo, and Pt) in the Tigris River, while Al, Fe, Pb, Th, and Ti were exhibiting high particulate fractions, with a trend of particle partition coefficients of [Ti(40) > Th(35) > Fe(15) > Al(13) > Pb(4.5)] ∗ 106 L/kg. Particulate forms of all metals exhibited high concentrations in the Diyala River, though the partition coefficients were low due to high TSS (~270 mg/L). A comparison of Tigris with the major rivers of the world showed that Tigris quality in Baghdad is comparable to Seine River quality in Paris. PMID:23304083

Emissions of particulate matter from animal houses in the Netherlands

NASA Astrophysics Data System (ADS)

Winkel, Albert; Mosquera, Julio; Groot Koerkamp, Peter W. G.; Ogink, Nico W. M.; Aarnink, André J. A.

2015-06-01

In the Netherlands, emissions from animal houses represent a major source of ambient particulate matter (PM). The objective of the present paper was to provide accurate and up to date concentrations and emission rates of PM10 and PM2.5 for commonly used animal housing systems, under representative inside and outside climate conditions and ventilation rates. We set up a national survey which covered 13 housing systems for poultry, pigs, and dairy cattle, and included 36 farms. In total, 202 24-h measurements were carried out, which included concentrations of inhalable PM, PM10, PM2.5, and CO2, ventilation rate, temperature, and relative humidity. On an animal basis, geometric mean emission rates of PM10 ranged from 2.2 to 12.0 mg h-1 in poultry and from 7.3 to 22.5 mg h-1 in pigs. The mean PM10 emission rate in dairy cattle was 8.5 mg h-1. Geometric mean emission rates of PM2.5 ranged from 0.11 to 2.41 mg h-1 in poultry and from 0.21 to 1.56 mg h-1 in pigs. The mean PM2.5 emission rate in dairy cattle was 1.65 mg h-1. Emissions are also reported per Livestock Unit and Heat Production Unit. PM emission rates increased exponentially with increasing age in broilers and turkeys and increased linearly with increasing age in weaners and fatteners. In laying hens, broiler breeders, sows, and dairy cattle, emission levels were variable throughout the year.

Correlation of fungi and endotoxin with PM2.5 and meteorological parameters in atmosphere of Sao Paulo, Brazil

NASA Astrophysics Data System (ADS)

Degobbi, Cristiane; Lopes, Fernanda D. T. Q. S.; Carvalho-Oliveira, Regiani; Muñoz, Julian Esteban; Saldiva, Paulo H. N.

2011-04-01

Particulate matter, especially PM2.5, is associated with increased morbidity and mortality from respiratory diseases. Studies that focus on the chemical composition of the material are frequent in the literature, but those that characterize the biological fraction are rare. The objectives of this study were to characterize samples collected in Sao Paulo, Brazil on the quantity of fungi and endotoxins associated with PM2.5, correlating with the mass of particulate matter, chemical composition and meteorological parameters. We did that by Principal Component Analysis (PCA) and multiple linear regressions. The results have shown that fungi and endotoxins represent significant portion of PM2.5, reaching average concentrations of 772.23 spores μg -1 of PM2.5 (SD: 400.37) and 5.52 EU mg -1 of PM2.5 (SD: 4.51 EU mg -1), respectively. Hyaline basidiospores, Cladosporium and total spore counts were correlated to factor Ba/Ca/Fe/Zn/K/Si of PM2.5 ( p < 0.05). Genera Pen/Asp were correlated to the total mass of PM2.5 ( p < 0.05) and colorless ascospores were correlated to humidity ( p < 0.05). Endotoxin was positively correlated with the atmospheric temperature ( p < 0.05). This study has shown that bioaerosol is present in considerable amounts in PM2.5 in the atmosphere of Sao Paulo, Brazil. Some fungi were correlated with soil particle resuspension and mass of particulate matter. Therefore, the relative contribution of bioaerosol in PM2.5 should be considered in future studies aimed at evaluating the clinical impact of exposure to air pollution.

[Effects of slopes on nitrogen transport along with runoff from sloping plots on a lateritic red soil amended with sewage sludge].

PubMed

Chen, Yan-Hui; Chen, Ming-Hua; Wang, Guo; Chen, Wen-Xiang; Yang, Shun-Cheng; Chai, Peng

2010-10-01

The effects of different slopes on nitrogen transport along with runoff from sloping plots amended with sewage sludge on a lateritic red soil were studied under simulated rainfall conditions. When the sludge was broadcasted and mixed with surface soils (BM), the MTN (total nitrogen of mixing sample), STN (total nitrogen of settled sample), TPN (total particulate nitrogen), TSN (total suspended nitrogen), TDN (total dissolved nitrogen) and NH4(+) -N concentrations and nitrogen loss amounts in runoff of all treatments were highest at 1 day or 18 days after application. The highest concentrations and the loss amounts of MTN and STN in the slope runoff for the BM treatment increased with slope degree, showing increasing pollution risks to the surface waters. The STN concentration and loss amounts from the 25 degrees plots were 126.1 mg x L(-1) and 1788.6 mg x m(-2), respectively, being 4.6 times and 5.8 times of the corresponding values from the 10 degrees plots, respectively. Then the concentrations and the loss amounts of nitrogen (except NO3(-) -N) from the BM plots diminished rapidly first and then tended to be stable with dwindling differences between the slopes. The loss of MTN and STN in early runoff (1 day and 18 days) accounted for 68.6% -73.4% and 62.3% -66.7% of the cumulative loss amounts during the experimental period for all the broadcasted treatments. Runoff loss coefficients of MTN increased in the order of 20 degrees > 25 degrees > 15 degrees > 10 degrees. Nitrogen was largely lost in dissolved species while large portion of NH4(+) -N was lost with particulates.

Particulate matter in pack ice of the Beaufort Gyre

USGS Publications Warehouse

Reimnitz, E.; Barnes, P.W.; Weber, W.S.

1993-01-01

Fine sediment occurred in very small patches of turbid ice, as thin spotty surface layers, in mud pellets or in old snowdrifts. The latter were widespread south of 74??N, containing an estimated 22 tonnes of silt and clay km-2. Average particle concentration in sea ice (40 mg1-1) was much higher than in sea water (0.8 mg 1 -1) or in new snow. Assuming one-third of the load is released each year, the estimated deposition rate would equal the measured Holocene rate (~2cm 1000 year-1). Therefore, modern sea-ice rafting represents a substantial fraction of the total Arctic Ocean sediment budget. -from Authors

Phosphorus runoff from sewage sludge applied to different slopes of lateritic soil.

PubMed

Chen, Yan Hui; Wang, Ming Kuang; Wang, Guo; Chen, Ming Hua; Luo, Dan; Ding, Feng Hua; Li, Rong

2011-01-01

Sewage sludge (SS) applied to sloping fields at rates that exceed annual forest nutrient requirements can be a source of phosphorus (P) in runoff. This study investigates the effects of different slopes (18, 27, 36, and 45%) on P in runoff from plots amended with SS (120 Mg ha). Lateritic soil (pH 5.2) was exposed to five simulated rainfalls (90 mm h) on outdoor plots. When sludge was broadcast and mixed with surface soils, the concentrations and loss in runoff of total P in the mixed sample (MTP), total P in the settled sample (STP), total particulate P (TPP), total suspended P (TSP), and total dissolved P (TDP) were highest at 1 or 18 d after application. Initially, pollution risks to surface waters generally increased to different degrees with steeper slopes, and then diminished gradually with dwindling differences between the slopes. The runoff losses coefficient of MTP increased in the order 36 > 45 > 27 > 18%. The initial event (1 and 18 d) accounted for 67.0 to 83.6% of total runoff P losses. Particulate fraction were dominant carriers for P losses, while with the lower slopes there was higher content of P per unit particulate fraction in runoff. Phosphorus losses were greatly affected by the interaction of sludge-soil-runoff and the modification of soil properties induced by sludge amendment. It is recommended to choose lower slopes (<27%) to reduce risk of P losses. Thus, the risk of application sludge to sloping fields in acid soils should be studied further in the field under a wider diversity of conditions. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

The humoral immune response of mice exposed to simulated road paving-like asphalt fumes.

PubMed

Anderson, Stacey E; Munson, Albert E; Tomblyn, Seth; Meade, B Jean; Diotte, Nicole M

2008-07-01

Asphalt is a complex mixture of organic molecules, including polycyclic aromatic hydrocarbons (PAH), which have been reported to cause serious adverse health effects in humans. Workers in manufacturing and construction trades exposed to asphalt are potentially at risk for being exposed to asphalt fumes and PAHs. Epidemiological investigations have collected mounting evidence that chemicals found in asphalt fumes present carcinogenic and possibly immunotoxic hazards. Studies evaluating the immunotoxic effects of asphalt fume are limited due to the large number of variables associated with asphalt fume exposures. This work investigates the immuno-toxic effects of road paving-like asphalt fume by analyzing the in vivo IgM response to a T-dependent antigen after exposure to whole, vapor, and particulate phase road paving-like asphalt fumes and asphalt fume condensate. Systemic exposures via intraperitoneal injection of asphalt fume condensate (at 0.625 mg/kg) and the particulate phase (at 5 mg/kg) resulted in significant reductions in the specific spleen IgM response to SRBC. Pharyngeal aspiration of the asphalt fume condensate (at 5 mg/kg) also resulted in significant suppression of the IgM response to SRBC. A significant reduction in the specific spleen IgM activity was observed after inhalation exposure to whole asphalt fumes (35 mg/m(3)) and the vapor components (11 mg/m(3)). Dermal exposures to the asphalt fume condensate resulted in significant reductions in the total (at 50 mg/kg) and specific (at 250 mg/kg) spleen IgM response to SRBC. These results demonstrate that exposure to road paving-like asphalt fumes is immunosuppressive through systemic, respiratory, and dermal routes of exposure in a murine model and raise concerns regarding the potential for adverse immunological effects.

Phosphorus and nitrogen in runoff after phosphorus- or nitrogen-based manure applications.

PubMed

Miller, Jim J; Chanasyk, David S; Curtis, Tony W; Olson, Barry M

2011-01-01

Application of beef cattle () manure based on nitrogen (N) requirements of crops has resulted in elevated concentrations of soil test phosphorus (P) in surface soils, and runoff from this cropland can contribute to eutrophication of surface waters. We conducted a 3-yr field study (2005-2007) on a Lethbridge loam soil cropped to dryland barley () in southern Alberta, Canada to evaluate the effect of annual and triennial P-based and annual N-based feedlot manure on P and N in runoff. The manure was spring applied and incorporated. There was one unamended control plot. A portable rainfall simulator was used to generate runoff in the spring of each year after recent manure incorporation, and the runoff was analyzed for total P, total dissolved P, total particulate P, dissolved reactive P, total N, total dissolved N, total particulate N, NO-N, and NH-N. Annual or triennial P-based application resulted in significantly ( ≤ 0.05) lower (by 50 to 94%) concentrations or loads of mainly dissolved P fractions in runoff for some years compared with annual N-based application, and this was related to lower rates of annual manure P applied. For example, mean dissolved reactive P concentrations in 2006 and 2007 were significantly lower for the annual P-based (0.12-0.20 mg L) than for the annual N-based application (0.24-0.48 mg L), and mean values were significantly lower for the triennial P-based (0.06-0.13 mg L) than for the annual N-based application. In contrast, other P fractions in runoff were unaffected by annual P-based application. Our findings suggested no environmental benefit of annual P-based application over triennial P-based application with respect to P and N in runoff. Similar concentrations and loads of N fractions in runoff for the P- and N-based applications indicated that shifting to a P-based application would not significantly influence N in runoff. American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America.

The sodium channel in membranes of electroplax. Binding of batrachotoxinin-a [(3)H]benzoate to particulate preparations from electric eel (electrophorus).

PubMed

McNeal, E T; Daly, J W

1986-01-01

Batrachotoxinin-A [(3)H]benzoate ([(3)H]BTX-B) binds specifically and with high affinity (K(D) 48 nM) to sites (B(max) 2.1 pmol/mg protein) associated with voltage-dependent sodium channels in rodent brain vesicular preparations. High affinity binding requires the presence of scorpion (Leiurus) venom and a membrane potential. Local anesthetics antagonize the binding. Nonspecific binding is defined in the presence of veratridine. In particulate preparations from electroplax of the eel Electrophorus electricus, [(3)H]BTX-B binds with a K(D) of about 140 nM and a B(max) of 2.5 pmol/mg protein in the presence of scorpion venom. Higher concentrations of scorpion venom are required to enhance binding in Electrophorus preparations than in brain preparations. Local anesthetics antagonize binding in Electrophorus preparations with potencies similar to those in brain preparations. Veratridine and batrachotoxin are less potent in blocking binding in Electrophorus than in brain preparations. It appears likely that binding in Electrophorus preparations is primarily to membrane fragments rather than vesicular entities as in brain. Binding of [(3)H]BTX-B to particulate preparations from electroplax of the ray Torpedo californica and the catfish Malapterurus electricus is mainly nonspecific. Scorpion venom does not enhance total binding and local anesthetics are not effective in antagonizing binding.

Particulate and colloidal silver in sewage effluent and sludge discharged from British wastewater treatment plants.

PubMed

Johnson, Andrew C; Jürgens, Monika D; Lawlor, Alan J; Cisowska, Iwona; Williams, Richard J

2014-10-01

Differential filtration was used to measure silver (>2 nm) entering and leaving nine sewage treatment plants (STPs). The mean concentration of colloidal (2-450 nm) silver, which includes nanosilver, was found to be 12 ng L(-1) in the influent and 6 ng L(-1) in the effluent. For particulate silver (>450 nm) the mean values were 3.3 μg L(-1) for influent and 0.08 μg L(-1) for effluent. Thus, removal was around 50% and 98% for colloidal and particulate silver respectively. There was no significant difference in performance between the different types of STP investigated (three examples each of activated sludge, biological filter and biological filter with tertiary treatment located across England, UK). In addition, treated sewage sludge samples (biosolids) were taken from several STPs to measure the total silver likely to be discharged to soils. Total silver was 3-14 mg kg(-1) DW in the sludge (median 3.6), which if the sludge were added at the recommended rate to soil, would add 11 μg kg(-1) yr(-1) to the top 20 cm soil layer. Predicted concentrations using the LF2000-WQX model for all the rivers of England and Wales for nanosilver were typically in the 0-1 ng L(-1) range but levels up to 4 ng L(-1) are possible in a high discharge and low flow scenario. Predicted concentrations for the total particulate forms were mostly below 50 ng L(-1) except for a high discharge and low flow scenario where concentrations could reach 135 ng L(-1). Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of vibratory microscreening on proximate composition and recovery of poultry processing wastewater particulate matter.

PubMed

Kiepper, B H; Merka, W C; Fletcher, D L

2008-12-01

Experiments were conducted to compare the effects of tertiary microscreen gap size on the proximate composition and rate of recovery of particulate matter from poultry processing wastewater (PPW). A high-speed vibratory screen was installed within the wastewater treatment area of a southeast US broiler slaughter plant after the existing primary and secondary mechanical rotary screens. Microscreen panels with nominal gap size openings of 212, 106 and 45mum were investigated. The particulate matter samples recovered were subjected to proximate analysis to determine percent moisture, fat, protein, crude fiber and ash. The average percent wet weight moisture (%WW) content for all samples was 79.1. The average percent dry matter (%DM) fat, protein, crude fiber and ash were 63.5, 17.5, 4.8 and 1.5, respectively. The mean concentration of total solids (TS) recovered from all microscreen runs was 668mg/L, which represents a potential additional daily offal recovery rate of 12.1metric tons (MT) per 3.78 million L (1.0 million gallons US) of PPW. There was no significant difference in the performance of the three microscreen gap sizes with regard to proximate composition or mass of particulate matter recovered.

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Asphalt Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

Organic carbon mineralization in the Santa Catalina Basin: benthic boundary layer metabolism

NASA Astrophysics Data System (ADS)

Smith, K. L.; Carlucci, A. F.; Jahnke, R. A.; Craven, D. B.

1987-02-01

Organic carbon mineralization rates in the benthic boundary layer (BBL) of the Santa Catalina Basin (1300 m depth) were estimated to identify the primary sites and organisms involved in the turnover of carbon and to compare these rates with the supply of particulate organic matter entering the system from above. Concurrent in situ measurements of macrozooplankton, epibenthic megafauna, and sediment community oxygen consumption, and bacterioplankton and total microbial (microplankton) metabolism were made on 12 dives with DSRV Alvin in November 1984. Pore water and solid phase chemistries, and sediment microbial activity were measured on samples from box cores. Macrozooplankton oxygen consumption, integrated over the 100 m BBL, was 25.8 μmol O 2 m -2 d -1 (0.3 mg C m -2 d -1). Microplankton carbon mineralization rates were 13-29 mg C m -2 d -1 for the BBL with an assimilation efficiency of 80-90%. The estimated oxygen consumption of the dominant population of epibenthic megafauna, Ophiophthalmus normani, at observed densities was 237.8 μmol O 2 m -2 d -1 (2.4 mg C m -2 d -1). Sediment community oxygen consumption was 2776.8 μmol O 2 m -2 d -1 (28.6 mg C m -2 d -1) which is similar to the estimated microbial carbon mineralization estimate for the sediments of 32 mg C m -2 d -1 assuming a 90% assimilation efficiency. These rates were corroborated further by the observed total inorganic carbon pore water gradients from which a mineralization rate of 10-31 mg C m -2 d -1 was estimated. The combined carbon mineralization by the three consumer groups ranged from 25.7 to 63.7 mg C m -2 d -1. For comparison, the oxygen consumption in the BBL based on hydrographic data from the center and sills of the basin was 3.1-20.0 mg C m -2 d -1. Given the large uncertainties in all of the calculations, there was reasonable agreement between these diverse methods of estimating carbon mineralization. The concurrently measured flux of small particulate organic carbon into the BBL using sediment traps was 11.1 ± 2.4 mg C m -2 d -1, providing 17-43% of the estimated carbon mineralized by the three consumer groups.

An initial investigation into the organic matter biogeochemistry of the Congo River

NASA Astrophysics Data System (ADS)

Spencer, Robert G. M.; Hernes, Peter J.; Aufdenkampe, Anthony K.; Baker, Andy; Gulliver, Pauline; Stubbins, Aron; Aiken, George R.; Dyda, Rachael Y.; Butler, Kenna D.; Mwamba, Vincent L.; Mangangu, Arthur M.; Wabakanghanzi, Jose N.; Six, Johan

2012-05-01

The Congo River, which drains pristine tropical forest and savannah and is the second largest exporter of terrestrial carbon to the ocean, was sampled in early 2008 to investigate organic matter (OM) dynamics in this historically understudied river basin. We examined the elemental (%OC, %N, C:N), isotopic (δ13C, Δ14C, δ15N) and biochemical composition (lignin phenols) of coarse particulate (>63 μm; CPOM) and fine particulate (0.7-63 μm; FPOM) OM and DOC, δ13C, Δ14C and lignin phenol composition with respect to dissolved OM (<0.7 μm; DOM) from five sites in the Congo River Basin. At all sample locations the organic carbon load was dominated by the dissolved phase (˜82-89% of total organic carbon) and the total suspended sediment load was principally fine particulate material (˜81-91% fine suspended sediment). Distinct compositional and isotopic differences were observed between all fractions. Congo CPOM, FPOM and DOM all originated from vegetation and soil inputs as evidenced by elemental, isotopic and lignin phenol data, however FPOM was derived from much older carbon pools (mean Δ14C = -62.2 ± -13.2‰, n = 5) compared to CPOM and DOM (mean Δ14C = 55.7 ± 30.6‰, n = 4 and 73.4 ± 16.1‰, n = 5 respectively). The modern radiocarbon ages for DOM belie a degraded lignin compositional signature (i.e. elevated acid:aldehyde ratios (Ad:Al) relative to CPOM and FPOM), and indicate that the application of OM degradation patterns derived from particulate phase studies to dissolved samples needs to be reassessed: these elevated ratios are likely attributable to fractionation processes during solubilization of plant material. The relatively low DOM carbon-normalized lignin yields (Λ8; 0.67-1.12 (mg(100 mg OC)-1)) could also reflect fractionation processes, however, they have also been interpreted as an indication of significant microbial or algal sources of DOM. CPOM appears to be well preserved higher vascular plant material as evidenced by its modern radiocarbon age, elevated C:N (17.2-27.1) and Λ8 values (4.56-7.59 (mg(100 mg OC)-1)). In relation to CPOM, the aged FPOM fraction (320-580 ybp 14C ages) was comparatively degraded, as demonstrated by its nitrogen enrichment (C:N 11.4-14.3), lower Λ8 (2.80-4.31 (mg(100 mg OC)-1)) and elevated lignin Ad:Al values similar to soil derived OM. In this study we observed little modification of the OM signature from sample sites near the cities of Brazzaville and Kinshasa to the head of the estuary (˜350 km) highlighting the potential for future studies to assess seasonal and long-term OM dynamics from this logistically feasible location and derive relevant information with respect to OM exported to the Atlantic Ocean. The relative lack of OM data for the Congo River Basin highlights the importance of studies such as this for establishing baselines upon which to gauge future change.

Inhalation of diesel engine exhaust increases bone mineral concentrations in growing rats.

PubMed

Watanabe, N; Nakamura, T

1996-03-01

Experiments were conducted to determine whether diesel engine exhaust affects bone metabolism in growing rats. The rats were assigned to three groups: those exposed to total diesel engine exhaust with 5.63 mg/m3 particulate matter, 4.10 ppm nitrogen dioxide, 8.10 ppm nitrogen monoxide; those exposed to filtered exhaust without particulate matter; and those exposed to clean air. Dosing experiments were performed for 3 months beginning at birth (6 h/day for 5 days/week). Bone mineral content (BMC) values in lumbar vertebral bone were significantly increased in both groups exposed to diesel exhaust (P < 0.01) compared to that of rats exposed to clean air. Bone mineral density (BMD) values were also significantly increased in both exposed groups, total exhaust (P < 0.01) and filtered exhaust (P < 0.001), compared to that of rats exposed to clean air. BMD values in the mid-femur were also significantly greater in animals exposed to diesel exhaust, total exhaust (P < 0.05), and filtered exhaust (P < 0.01), compared to that of those exposed to clean air. Urinary excretion of deoxypyridinolines, a biochemical marker for bone resorption, was significantly reduced in animals exposed to total diesel exhaust and filtered exhaust (P < 0.001, P < 0.01) compared to control. There was also a significant difference between the two exposure groups of diesel exhaust (P < 0.05). Since these effects were not inhibited by filtration, the gaseous phase of the exhaust was considered more responsible than particulate matter for reducing bone resorption.

Variability in sinking fluxes and composition of particle-bound phosphorus in the Xisha area of the northern South China Sea

NASA Astrophysics Data System (ADS)

Dong, Yuan; Li, Qian P.; Wu, Zhengchao; Zhang, Jia-Zhong

2016-12-01

Export fluxes of phosphorus (P) by sinking particles are important in studying ocean biogeochemical dynamics, whereas their composition and temporal variability are still inadequately understood in the global oceans, including the northern South China Sea (NSCS). A time-series study of particle fluxes was conducted at a mooring station adjacent to the Xisha Trough in the NSCS from September 2012 to September 2014, with sinking particles collected every two weeks by two sediment traps deployed at 500 m and 1500 m depths. Five operationally defined particulate P classes of sinking particles including loosely-bound P, Fe-bound P, CaCO3-bound P, detrital apatite P, and refractory organic P were quantified by a sequential extraction method (SEDEX). Our results revealed substantial variability in sinking particulate P composition at the Xisha over two years of samplings. Particulate inorganic P was largely contributed from Fe-bound P in the upper trap, but detrital P in the lower trap. Particulate organic P, including exchangeable organic P, CaCO3-bound organic P, and refractory organic P, contributed up to 50-55% of total sinking particulate P. Increase of CaCO3-bound P in the upper trap during 2014 could be related to a strong El Niño event with enhanced CaCO3 deposition. We also found sediment resuspension responsible for the unusual high particles fluxes at the lower trap based on analyses of a two-component mixing model. There was on average a total mass flux of 78±50 mg m-2 d-1 at the upper trap during the study period. A significant correlation between integrated primary productivity in the region and particle fluxes at 500 m of the station suggested the important role of biological production in controlling the concentration, composition, and export fluxes of sinking particulate P in the NSCS.

Flow and sorption controls of groundwater arsenic in individual boreholes from bedrock aquifers in central Maine, USA.

PubMed

Yang, Qiang; Culbertson, Charles W; Nielsen, Martha G; Schalk, Charles W; Johnson, Carole D; Marvinney, Robert G; Stute, Martin; Zheng, Yan

2015-02-01

To understand the hydrogeochemical processes regulating well water arsenic (As) evolution in fractured bedrock aquifers, three domestic wells with [As] up to 478 μg/L are investigated in central Maine. Geophysical logging reveals that fractures near the borehole bottom contribute 70-100% of flow. Borehole and fracture water samples from various depths show significant proportions of As (up to 69%) and Fe (93-99%) in particulates (>0.45 μm). These particulates and those settled after a 16-day batch experiment contain 560-13,000 mg/kg of As and 14-35% weight/weight of Fe. As/Fe ratios (2.5-20 mmol/mol) and As partitioning ratios (adsorbed/dissolved [As], 20,000-100,000 L/kg) suggest that As is sorbed onto amorphous hydrous ferric oxides. Newly drilled cores also show enrichment of As (up to 1300 mg/kg) sorbed onto secondary iron minerals on the fracture surfaces. Pumping at high flow rates induces large decreases in particulate As and Fe, a moderate increase in dissolved [As] and As(III)/As ratio, while little change in major ion chemistry. The δD and δ(18)O are similar for the borehole and fracture waters, suggesting a same source of recharge from atmospheric precipitation. Results support a conceptual model invoking flow and sorption controls on groundwater [As] in fractured bedrock aquifers whereby oxygen infiltration promotes the oxidation of As-bearing sulfides at shallower depths in the oxic portion of the flow path releasing As and Fe; followed by Fe oxidation to form Fe oxyhydroxide particulates, which are transported in fractures and sorb As along the flow path until intercepted by boreholes. In the anoxic portions of the flow path, reductive dissolution of As-sorbed iron particulates could re-mobilize As. For exposure assessment, we recommend sampling of groundwater without filtration to obtain total As concentration in groundwater. Copyright © 2014 Elsevier B.V. All rights reserved.

Flow and sorption controls of groundwater arsenic in individual boreholes from bedrock aquifers in central Maine, USA

PubMed Central

Yang, Qiang; Culbertson, Charles W.; Nielsen, Martha G.; Schalk, Charles W.; Johnson, Carole D.; Marvinney, Robert G.; Stute, Martin; Zheng, Yan

2014-01-01

To understand the hydrogeochemical processes regulating well water arsenic (As) evolution in fractured bedrock aquifers, three domestic wells with [As] up to 478 µg/L are investigated in central Maine. Geophysical logging reveals that fractures near the borehole bottom contribute 70–100% of flow. Borehole and fracture water samples from various depths show significant proportions of As (up to 69%) and Fe (93–99%) in particulates (>0.45 µm). These particulates and those settled after a 16-day batch experiment contain 560–13,000 mg/kg of As and 14–35% weight/weight of Fe. As/Fe ratios (2.5–20 mmole/mole) and As partitioning ratios (adsorbed/dissolved [As], 20,000–100,000 L/kg) suggest that As is sorbed onto amorphous hydrous ferric oxides. Newly drilled cores also show enrichment of As (up to 1,300 mg/kg) sorbed onto secondary iron minerals on the fracture surfaces. Pumping at high flow rates induces large decreases in particulate As and Fe, a moderate increase in dissolved [As] and As(III)/As ratio, while little change in major ion chemistry. The δD and δ18O are similar for the borehole and fracture waters, suggesting a same source of recharge from atmospheric precipitation. Results support a conceptual model invoking flow and sorption controls on groundwater [As] in fractured bedrock aquifers whereby oxygen infiltration promotes oxidation of As-bearing sulfides at shallower depths in the oxic portion of the flow path releasing As and Fe; followed by Fe oxidation to form Fe oxyhydroxide particulates, which are transported in fractures and sorb As along the flow path until intercepted by boreholes. In the anoxic portions of the flow path, reductive dissolution of As-sorbed iron particulates could re-mobilize As. For exposure assessment, we recommend sampling of groundwater without filtration to obtain total As concentration in groundwater. PMID:24842411

Subsurface sediment contamination during borehole drilling with an air-actuated down-hole hammer.

PubMed

Malard, Florian; Datry, Thibault; Gibert, Janine

2005-10-01

Drilling methods can severely alter physical, chemical, and biological properties of aquifers, thereby influencing the reliability of water samples collected from groundwater monitoring wells. Because of their fast drilling rate, air-actuated hammers are increasingly used for the installation of groundwater monitoring wells in unconsolidated sediments. However, oil entrained in the air stream to lubricate the hammer-actuating device can contaminate subsurface sediments. Concentrations of total hydrocarbons, heavy metals (Cu, Ni, Cr, Zn, Pb, and Cd), and nutrients (particulate organic carbon, nitrogen, and phosphorus) were measured in continuous sediment cores recovered during the completion of a 26-m deep borehole drilled with a down-hole hammer in glaciofluvial deposits. Total hydrocarbons, Cu, Ni, Cr and particulate organic carbon (POC) were all measured at concentrations far exceeding background levels in most sediment cores. Hydrocarbon concentration averaged 124 +/- 118 mg kg(-1) dry sediment (n = 78 samples) with peaks at depths of 8, 14, and 20 m below the soil surface (maximum concentration: 606 mg kg(-1)). The concentrations of hydrocarbons, Cu, Ni, Cr, and POC were positively correlated and exhibited a highly irregular vertical pattern, that probably reflected variations in air loss within glaciofluvial deposits during drilling. Because the penetration of contaminated air into the formation is unpreventable, the representativeness of groundwater samples collected may be questioned. It is concluded that air percussion drilling has strong limitations for well installation in groundwater quality monitoring surveys.

Pre- and post-impoundment nitrogen in the lower Missouri River

USGS Publications Warehouse

Blevins, Dale W.; Wilkison, Donald H.; Niesen, Shelley L.

2013-01-01

Large water-sample sets collected from 1899 through 1902, 1907, and in the early 1950s allow comparisons of pre-impoundment and post-impoundment (1969 through 2008) nitrogen concentrations in the lower Missouri River. Although urban wastes were not large enough to detectably increase annual loads of total nitrogen at the beginning of the 20th century, carcass waste, stock-yard manure, and untreated human wastes measurably increased ammonia and organic-nitrogen concentrations during low flows. Average total-nitrogen concentrations in both periods were about 2.5 mg/l, but much of the particulate-organic nitrogen, which was the dominant form of nitrogen around 1900, has been replaced by nitrate. This change in speciation was caused by the nearly 80% decrease in suspended-sediment concentrations that occurred after impoundment, modern agriculture, drainage of riparian wetlands, and sewage treatment. Nevertheless, bioavailable nitrogen has not been low enough to limit primary production in the Missouri River since the beginning of the 20th century. Nitrate concentrations have increased more rapidly from 2000 through 2008 (5 to 12% per year), thus increasing bioavailable nitrogen delivered to the Mississippi River and affecting Gulf Coast hypoxia. The increase in nitrate concentrations with distance downstream is much greater during the post-impoundment period. If strategies to decrease total-nitrogen loads focus on particulate N, substantial decreases will be difficult because particulate nitrogen is now only 23% of total nitrogen in the Missouri River. A strategy aimed at decreasing particulates also could further exacerbate land loss along the Gulf of Mexico, which has been sediment starved since Missouri River impoundment. In contrast, strategies or benchmarks aimed at decreasing nitrate loads could substantially decrease nitrogen loadings because nitrates now constitute over half of the Missouri's nitrogen input to the Mississippi. Ongoing restoration and creation of wetlands along the Missouri River could be part of such a nitrate-reduction strategy. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.

Characteristics of trace metals in traffic-derived particles in Hsuehshan Tunnel, Taiwan: size distribution, fingerprinting metal ratio, and emission factor

NASA Astrophysics Data System (ADS)

Lin, Y.-C.; Tsai, C.-J.; Wu, Y.-C.; Zhang, R.; Chi, K.-H.; Huang, Y.-T.; Lin, S.-H.; Hsu, S.-C.

2014-05-01

Traffic emissions are a significant source of airborne particulate matter (PM) in ambient environments. These emissions contain high abundance of toxic metals and thus pose adverse effects on human health. Size-fractionated aerosol samples were collected from May to September 2013 by using micro-orifice uniform deposited impactor (MOUDI). Sample collection was conducted simultaneously at the inlet and outlet sites of Hsuehshan Tunnel in northern Taiwan, which is the second longest freeway tunnel (12.9 km) in Asia. Such endeavor aims to characterize the chemical constituents, size distributions, and fingerprinting ratios, as well as the emission factors of particulate metals emitted by vehicle fleets. A total of 36 metals in size-resolved aerosols were determined through inductively coupled plasma mass spectrometry. Three major groups, namely, tailpipe emissions (Zn, Pb, and V), wear debris (Cu, Cd, Fe, Ga, Mn, Mo, Sb, and Sn), and resuspended dust (Ca, Mg, K, and Rb), of airborne PM metals were categorized on the basis of the results of enrichment factor, correlation matrix, and principal component analysis. Size distributions of wear-originated metals resembled the pattern of crustal elements, which were predominated by super-micron particulates (PM1-10). By contrast, tailpipe exhaust elements such as Zn, Pb, and V were distributed mainly in submicron particles. By employing Cu as a tracer of wear abrasion, several inter-metal ratios, including Fe/Cu (14), Ba/Cu (1.05), Sb/Cu (0.16), Sn/Cu (0.10), and Ga/Cu (0.03), served as fingerprints for wear debris. Emission factor of PM10 mass was estimated to be 7.7 mg vkm-1. The metal emissions were mostly predominated in super-micron particles (PM1-10). Finally, factors that possibly affect particulate metal emissions inside Hsuehshan Tunnel are discussed.

Environmental assessment of a firetube boiler firing coal/oil/water mixtures. Volume 1. Technical results. Final report, February 1981-November 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeRosier, R.

1984-09-01

This volume describes emission results from sampling of flue-gas from a firetube boiler burning a coal/oil/water (COW) mixture and COW with soda ash added (COW+SA) to control SO/sub 2/ emissions. Measurements included: continuous monitoring of flue-gas emissions; source assessment sampling system (SASS) sampling of the flue gas with subsequent laboratory analysis of the samples to give total flue gas organics in two boiling point ranges, specific quantitation of the semivolatile organic priority pollutant species, and flue gas concentrations of 73 trace elements; Method 5 sampling for total particulate; and controlled condensation system sampling for SO/sub 2/ and SO/sub 3/ emissions.more » Flue-gas SO/sub 2/ emissions decreased almost 99% with soda ash addition from 1,089 to 13.6 ppm (3% O2). NOx emissions decreased slightly from 477 to 427 ppm, while CO emissions increased significantly from an average of 25 to 426 ppm (all at 3% O2). Particulate loading at the boiler outlet almost doubled (from 1,970 to 3,715 pg/dscm) with the additive. The size distribution of particulate also shifted to a much smaller mean diameter. Total organic emissions increased from 6.7 to 13.1 mg/dscm; most of the increase were nonvolatile (C16+) organics. Of the semivolatile organic priority pollutant species, only fluoranthene and phenanthrene were detected with the COW fuel, and phenanthrene with the COW+SA fuel.« less

Emissions of particulate-bound elements from biodiesel and ultra low sulfur diesel: size distribution and risk assessment.

PubMed

Betha, Raghu; Balasubramanian, Rajasekhar

2013-01-01

Use of waste cooking oil derived biodiesel (WCOB) as an alternative fuel in diesel engines has increased significantly in recent years. The impact of WCOB on particulate emissions from diesel engines needs to be investigated thoroughly. This study was conducted to make a comparative evaluation and size-differentiated speciation of the particulate bound elements from ultra low sulfur diesel (ULSD) and WCOB and a blend of both of the fuels (B50). Particle mass and their elemental size distributions ranging from 0.01-5.6 μm were measured. It was observed that more ultrafine particles (UFPs, <100 nm) were emitted when the engine was fueled with WCOB. Fifteen particulate-bound elements such as K, Al, Mg, Co, Cr, Cu, Fe, Mn, Cd, Ni, As, Ba, Pb, Zn and Sr were investigated and reported in this study. Potential health risk associated with these particulate bound elements upon inhalation was also evaluated based on dose-response assessments for both adults and children. The findings indicate that the exposure to PM of the B100 exhaust is relatively more hazardous and may pose adverse health effects compared to that of ULSD. Also, investigations on human health risk due to exposure to UFPs indicate that UFPs contribute a major fraction (>70%) of the total estimated health risk. Copyright © 2012 Elsevier Ltd. All rights reserved.

Global mercury emissions from combustion in light of international fuel trading.

PubMed

Chen, Yilin; Wang, Rong; Shen, Huizhong; Li, Wei; Chen, Han; Huang, Ye; Zhang, Yanyan; Chen, Yuanchen; Su, Shu; Lin, Nan; Liu, Junfeng; Li, Bengang; Wang, Xilong; Liu, Wenxin; Coveney, Raymond M; Tao, Shu

2014-01-01

The spatially resolved emission inventory is essential for understanding the fate of mercury. Previous global mercury emission inventories for fuel combustion sources overlooked the influence of fuel trading on local emission estimates of many countries, mostly developing countries, for which national emission data are not available. This study demonstrates that in many countries, the mercury content of coal and petroleum locally consumed differ significantly from those locally produced. If the mercury content in locally produced fuels were used to estimate emission, then the resulting global mercury emissions from coal and petroleum would be overestimated by 4.7 and 72%, respectively. Even higher misestimations would exist in individual countries, leading to strong spatial bias. On the basis of the available data on fuel trading and an updated global fuel consumption database, a new mercury emission inventory for 64 combustion sources has been developed. The emissions were mapped at 0.1° × 0.1° resolution for 2007 and at country resolution for a period from 1960 to 2006. The estimated global total mercury emission from all combustion sources (fossil fuel, biomass fuel, solid waste, and wildfires) in 2007 was 1454 Mg (1232-1691 Mg as interquartile range from Monte Carlo simulation), among which elementary mercury (Hg(0)), divalent gaseous mercury (Hg(2+)), and particulate mercury (Hg(p)) were 725, 548, and 181 Mg, respectively. The total emission from anthropogenic sources, excluding wildfires, was 1040 Mg (886-1248 Mg), with coal combustion contributing more than half. Globally, total annual anthropogenic mercury emission from combustion sources increased from 285 Mg (263-358 Mg) in 1960 to 1040 Mg (886-1248 Mg) in 2007, owing to an increased fuel consumption in developing countries. However, mercury emissions from developed countries have decreased since 2000.

Particulate and dissolved spectral absorption on the continental shelf of the southeastern United States

NASA Astrophysics Data System (ADS)

Nelson, James R.; Guarda, Sonia

1995-05-01

Visible absorption spectra of particulate and dissolved materials were characterized on the continental shelf off the southeastern United States (the South Atlantic Bight), emphasizing cross-shelf and seasonal variability. A coastal front separates turbid coastal waters from clearer midshelf waters. Spatial and seasonal patterns were evident in absorption coefficients for phytoplankton, detritus, and colored dissolved organic matter (CDOM); spectral shape parameters for CDOM and detritus; and phytoplankton chlorophyll-specific absorption. The magnitude of CDOM absorption reflected seasonal differences in freshwater discharge and the salinity of the midshelf waters. In the spring of 1993 (high discharge), CDOM absorption at 443 nm was >10 times that of total particulate absorption between 12 and 50 km offshore (0.28-0.69 m-1 versus 0.027-0.062 m-1) and up to 10 times the CDOM absorption measured in the previous summer (low discharge). Phytoplankton chlorophyll-specific absorption in the blue increased with distance from shore (from <0.03 m2 mg-1 in inner shelf waters to ˜0.1 m2 mg-1 at the most seaward stations in summer) and, for similar chlorophyll concentrations, was higher in summer than in the winter-spring. These spatial and seasonal patterns in phytoplankton chlorophyll-specific absorption can be attributed to a shift in phytoplankton species composition (from predominantly diatoms inshore to a cyanobacteria-dominated assemblage midshelf in summer), pigment packaging, and higher carotenoid:chlorophyll with distance from shore.

Air pollution and rural biomass fuels in developing countries: A pilot village study in India and implications for research and policy

NASA Astrophysics Data System (ADS)

Smith, Kirk R.; Aggarwal, A. L.; Dave ^✠, R. M.

The results of a pilot study in four Indian villages of personal exposure to total suspended particulates (TSP) and particulate benzo(a)pyrene (BaP) of women cooking on simple stoves using traditional biomass fuels are presented together with socioeconomic and fuel-use determinations. TSP exposures averaged nearly 7 mg m -3 and BaP about 4000 ng m -3 during the cooking period which occupied 10% of the year. The factors affecting indoor air pollution exposures in rural areas of developing countries are categorized and discussed by reference to the few published field measurements. Comparisons are made with other common exposures in urban and occupational settings. The sparse information indicates that rural exposures are relatively high. Subjects for future research are outlined and general policy implications mentioned.

Carbon, nitrogen, and phosphorus transport by world rivers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meybeck, M.

1982-04-01

The various forms (dissolved and particulate, organic and inorganic) of carbon, nitrogen, and phosphorus in world rivers are reviewed from literature data. Natural levels are based mainly on major rivers for the subarctic and tropical zones which are still unpolluted and on smaller streams for the temperate zone. Atmospheric fallout is also reviewed. Natural contents of dissolved organic carbon (DOC) are mainly dependent on environmental conditions: DOC varies from 1 mg 1/sup -1/ in the mountainous alpine environments to 20 mg 1/sup -1/ in some taiga rivers. The world DOC average is 5.75 mg l/sup -1/. Nitrogen forms include dissolvedmore » organic nitrogen (DON), dissolved inorganic nitrogen (DIN = N - NH/sub 4//sup +/ + N - NO/sub 3//sup -/ + N - NO/sub 2//sup -/), and particulate organic nitrogen (PON). Natural levels are very low: DIN = 120 ..mu..g 1/sup -1/ of which only 15 percent is present as ammonia, and 1 percent as nitrite. Phosphorus is naturally present in very low amounts: around 10 ..mu..g 1/sup -1/ for P-PO/sub 4//sup 3/ and 25 ..mu..g 1/sup -1/ for total dissolved phosphorus (TDP which includes the organic form). The average nutrient content of rains has been estimated with a set of unpolluted stations: P - PO/sub 4/ = 5 ..mu..g 1/sup -1/, TDP = 10, N - NO/sub 2/ = 5, N - NH/sub 4/ = 225, DON = 225, and N - NO/sub 3/ = 175 ..mu..g 1/sup -1/. TOC levels are probably around several mg 1/sup -1/. These contents are very similar to those found in unpolluted rivers. Man's influence on surface waters has now greatly increased natural nutrient levels. Total dissolved P and N have globally increased by a factor of two and locally (Western Europe, North America) by factors of 10 to 50. These increases were found to be directly proportional to the watershed population and to its energy consumption.« less

Comparison of high MRI T1 signals with manganese concentration in brains of cynomolgus monkeys after 8 months of stainless steel welding-fume exposure.

PubMed

Park, Jung Duck; Chung, Yong Hyun; Kim, Choong Yong; Ha, Chang Soo; Yang, Seoung Oh; Khang, Hyun Soo; Yu, In Kyu; Cheong, Hae Kwan; Lee, Jong Seong; Song, Chang-Woo; Kwon, Il Hoon; Han, Jeong Hee; Sung, Jae Hyuck; Heo, Jeong Doo; Choi, Byung Sun; Im, Ruth; Jeong, Jayoung; Yu, Il Je

2007-09-01

Several pharmacokinetic studies on inhalation exposure to manganese (Mn) have already demonstrated that Mn readily accumulates in the olfactory and brain regions. However, a shortening of the magnetic resonance imaging (MRI) T1 relaxation time or high T1 signal intensity in specific sites of the brain, including the globus pallidus and subcortical frontal white matter, as indicative of tissue manganese accumulation has not yet been clearly established for certain durations of known doses of welding-fume exposure in experimental animals. Accordingly, to investigate the movement of manganese after welding-fume exposure, six cynomolgus monkeys were acclimated and assigned to three dose groups: unexposed, low dose (31 mg/m(3) total suspended particulate [TSP], 0.9 mg/m(3) of Mn), and high dose (62 mg/m(3) TSP, 1.95 mg/m(3) of Mn) of total suspended particulate. The primates were exposed to manual metal arc stainless steel (MMA-SS) welding fumes for 2 h per day in an inhalation chamber system equipped with an automatic fume generator. Magnetic resonance imaging (MRI) studies were conducted before the initiation of exposure and thereafter every month. The tissue Mn concentrations were then measured after a plateau was reached regarding the shortening of the MRI T1 relaxation time. A dose-dependent increase in the Mn concentration was found in the lungs, while noticeable increases in the Mn concentrations were found in certain tissues, such as the liver, kidneys, and testes. Slight increases in the Mn concentrations were found in the caudate, putamen, frontal lobe, and substantia nigra, while a dose-dependent noticeable increase was only found in the globus pallidus. Therefore, the present results indicated that a shortening of the MRI T1 relaxation time corresponded well with the Mn concentration in the globus pallidus after prolonged welding-fume exposure.

Enhanced accumulation of PCB congeners by Baltic Sea blue mussels, Mytilus edulis, with increased algae enrichment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilek, M.; Bjoerk, M.; Broman, D.

The objective of this study was to examine if natural variations in the quantity of phytoplankton-derived particulate and dissolved organic carbon influences the accumulation of polychlorinated biphenyls (PCBs) in the tissues of Baltic Sea blue mussels (Mytilus edulis L.). In a laboratory flow-through experiment the authors exposed M. edulis to the technical PCB mixture Aroclor{reg_sign} 1248 for 21 d at three different enrichments of the unicellular green algae Chlamydomonas sp., 0.10, 0.16, and 0.32 mg particulate organic carbon (POC)/L. Tissue and water concentrations were determined for seven PCB congeners and 21-d bioaccumulation factors were calculated against total water concentrations. Contrarymore » to what would be expected, an increase in algae enrichment from 0.10 to 0.32 mg POC/L resulted in an enhanced PCB accumulation by a factor of approx. 2. This increase in PCB accumulation was more pronounced for PCB congeners with lower hydrophobicity. These observations have implications for the design of laboratory accumulation studies and potentially for PCB accumulation and cycling in field populations of suspension-feeding mussels in response to changes in eutrophication status.« less

The exposure assessment of airborne particulates matter (PM10 & PM2.5) towards building occupants: A case study at KL Sentral, Kuala Lumpur, Malaysia

NASA Astrophysics Data System (ADS)

Mohddin, S. A.; Aminuddin, N. M.

2014-02-01

Airborne particulates have been recognized as a crucial pollutant of indoor air. These pollutants can contribute towards poor indoor air quality (IAQ), which may affect human health in immediate or long term. This study aims to determine the level of IAQ and the effects of particulate towards occupants of office buildings (the office buildings selected for the case study are SSM, KTMB and MRCB at KL Sentral). The objectives of study are (i) to measure the level of airborne particulates that contribute to the IAQ during working hours, (ii) to compare the level of airborne particulates with the existing guidelines and standards of IAQ in Malaysia and other Asian countries and (iii) to assess the symptoms associated with airborne particulates among the building occupants, which were achieved through primary data collection (case study or site survey, structured interview and questionnaire survey) and supported by literature reviews. The results showed that the mass concentration level of airborne particulates within the areas has exceeded the allowable limit of 0.15mg/m3 by IAQ Code of Practice, 2005 of the Department of Safety and Health (DOSH), Malaysia and 0.05mg/m3 by the Department of Environmental (DOE) (outdoor) of 8 hours continuous sampling. Based on the findings, the highest mass concentration values measured is 2.581 mg/m3 at lobby of SSM building which is the highest recorded 17 times higher from the maximum limit recommended by DOSH than the others. This is due to the nearby construction works and the high numbers of particulates are generated from various types of vehicles for transportation surrounding KL Sentral. Therefore, the development of Malaysian Ambient Air Quality Guidelines on PM2.5 as one of the crucial parameters is highly recommended.

Spatial variation of chemical constituents from the burning of commonly used biomass fuels in rural areas of the Indo-Gangetic Plain (IGP), India

NASA Astrophysics Data System (ADS)

Saud, T.; Saxena, M.; Singh, D. P.; Saraswati; Dahiya, Manisha; Sharma, S. K.; Datta, A.; Gadi, Ranu; Mandal, T. K.

2013-06-01

In the present paper, we have determined emission factor of chemical composition of the emission from the burning of biomass (e.g. Dung cake, Acacia, Neem, Mulberry, Indian Rosewood, Pigeon pea etc.) commonly used as a residential fuel in the rural sector of Indo-Gangetic Plain (IGP) (Delhi, Punjab, Haryana, Uttar Pradesh, Bihar and West Bengal), India. For comparison, we have selected only those biomass fuels, which are used in at least three of the above mentioned states. Dung cake from all the states reports highest emission of particulate matter (PM) (15.68 g kg-1), Organic Carbon (OC) (4.32 g kg-1) and Elemental Carbon (EC) (0.51 g kg-1). Among all biomass fuels studied, agricultural residue reports substantial amount of emission of Na+ (104 mg kg-1), K+ (331 mg kg-1) and Cl- (447 mg kg-1) particularly in Pigeon pea and Mustard stem. Eucalyptus (fuel wood) emits large amounts of Ca2+ (21.47 mg kg-1) and NO3- (614 mg kg-1). The emission of PM from dung cake is higher in Delhi (19.31 g kg-1) and followed by Uttar Pradesh (17.58 g kg-1) > Haryana (15.46 g kg-1) > Bihar (14.99 g kg-1) > Punjab (12.06 g kg-1) > West Bengal (5.90 g kg-1). Carbonaceous aerosols (OC and EC) and dominant Ionic species (Cl-, K+, SO42-, NO3- and PO43-) are altogether contributing 40-70% of total emissions. Characteristics and ratios of chemical species of emissions may help to develop a methodology of discriminating the sources of ambient particulate matter. Using a laboratory determined emission factor of chemical species, we have determined the emission budget over IGP, India.

40 CFR Table 7 to Subpart Ddddd of... - Establishing Operating Limits

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Particulate matter, mercury, or total selected metals a. Wet scrubber operating parameters i. Establish a site... drop and liquid flow rate monitors and the particulate matter, mercury, or total selected metals... from the pressure drop and liquid flow rate monitors and the particulate matter, mercury, or total...

Kuwaiti oil fires—Particulate monitoring

NASA Astrophysics Data System (ADS)

Husain, Tahir; Amin, Mohamed B.

The total suspended particulate (TSP) matters using a high-volume sampler and inhalable particulate matters using PM-10 samplers were collected at various locations in the Eastern Province of Saudi Arabia during and after the Kuwaiti oil fires. The collected samples were analysed for toxic metals and oil hydrocarbon concentrations including some carcinogenic organic compounds in addition to gravimetric analysis. The concentration values of particulate matters were determined on a daily basis at Dhahran. Abqaiq, Rahima, Tanajib and Jubail locations. The analyses of the filters show a high concentration of the inhalable particulate at various locations, especially when north or northwest winds were blowing. It was found that the inhalable particulate concentration exceeded the Meteorology and Environmental Protection Administration (MEPA) permissible limit of 340 μg m- 3 at most of these locations during May-October 1991. A trend between the total suspended particulate and inhalable particulate measured concurrently at the same locations was observed and a regression equation was developed to correlate PM-10 data with the total suspended particulate data.

Inhalation of diesel engine exhaust affects spermatogenesis in growing male rats.

PubMed

Watanabe, N; Oonuki, Y

1999-07-01

We conducted experiments to determine whether diesel engine exhaust affects reproductive endocrine function in growing rats. The rats were assigned to three groups: a group exposed to total diesel engine exhaust containing 5.63 mg/m3 particulate matter, 4.10 ppm nitrogen dioxide, and 8.10 ppm nitrogen oxide; a group exposed to filtered exhaust without particulate matter; and a group exposed to clean air. Dosing experiments were performed for 3 months beginning at birth (6 hr/day for 5 days/week). Serum levels of testosterone and estradiol were significantly higher in animals exposed to total diesel exhaust and filtered exhaust (p < 0.05 for each group) as compared to the controls. Follicle-stimulating hormone was significantly decreased in the two groups exposed to diesel exhaust as compared to the control group (p < 0.05). Luteinizing hormone was significantly decreased in the total exhaust-exposed group as compared to the control and filtered groups (p < 0.05). Although testis weight did not show any significant difference among the groups, sperm production and activity of testicular hyaluronidase were significantly reduced in both exhaust-exposed groups as compared to the control group. Histological examination showed decreased numbers of step 18 and 19 spermatids in stage VI, VII, and VIII tubules in the testes of both diesel exhaust-exposed groups. This study suggests that diesel exhaust stimulates hormonal secretion of the adrenal cortex, depresses gonadotropin-releasing-hormone, and inhibits spermatogenesis in rats. Because these effects were not inhibited by filtration, the gaseous phase of the exhaust appears to be more responsible than particulate matter for disrupting the endocrine system.

Environmental assessment of an enhanced-oil-recovery steam generator equipped with a low-NOx burner. Volume 1. Technical results. Final report, January 1984-January 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.; Lips, H.I.

1986-02-01

The report discusses results from sampling flue gas from an enhanced-oil-recovery steam generator (EOR steamer) equipped with an MHI PM low-NOx burner. The tests included burner performance/emission mapping tests, comparative testing of an identical steamer equipped with a conventional burner, and comprehensive testing of the low-NOx-burner-equipped steamer. Comprehensive test measurements included continuous flue-gas monitoring; source assessment sampling system testing with subsequent laboratory analysis to give total flue-gas organics in two boiling point ranges and specific quantitation on the semivolatile organic priority pollutants; C1 to C6 hydrocarbon sampling; Methods 5/8 sampling for particulate and SO/sub 2/ and SO/sub 3/ emissions; andmore » emitted particle size distribution tests using Andersen impactors. Full-load NOx emissions of 110 ppm (3% O/sub 2/) could be maintained from the low-NOx burner at acceptable CO and smoke emissions, compared to about 300 ppm (3% O/sub 2/) from the conventional-burner-equipped steamer. At the low-NOx condition, CO, SO/sub 2/, and SO/sub 3/ emissions were 93, 594, and 3.1 ppm, respectively. Particulate emissions were 39 mg/dscm with a mean particle diameter of 3 to 4 micrometers. Total organic emissions were 11.1 mg/dscm, almost exclusively volatile (C1 to C6) organics. Three PAHs were detected at from 0.1 to 1.4 micrograms/dscm.« less

Does microbial biomass affect pelagic ecosystem efficiency? An experimental study.

PubMed

Wehr, J D; Le, J; Campbell, L

1994-01-01

Bacteria and other microorganisms in the pelagic zone participate in the recycling of organic matter and nutrients within the water column. The microbial loop is thought to enhance ecosystem efficiency through rapid recycling and reduced sinking rates, thus reducing the loss of nutrients contained in organisms remaining within the photic zone. We conducted experiments with lake communities in 5400-liter mesocosms, and measured the flux of materials and nutrients out of the water column. A factorial design manipulated 8 nutrient treatments: 4 phosphorus levels × 2 nitrogen levels. Total sedimentation rates were greatest in high-N mesocosms; within N-surplus communities, [Symbol: see text]1 µM P resulted in 50% increase in total particulate losses. P additions without added N had small effects on nutrient losses from the photic zone; +2 µM P tanks received 334 mg P per tank, yet after 14 days lost only 69 mg more particulate-P than did control communities. Nutrient treatments resulted in marked differences in phytoplankton biomass (twofold N effect, fivefold P effect in +N mesocosms only), bacterioplankton densities (twofold N-effect, twofold P effects in -N and +N mesocosms), and the relative importance of autotrophic picoplankton (maximum in high NY mesocosms). Multiple regression analysis found that of 8 plankton and water chemistry variables, the ratio of autotrophic picoplankton to total phytoplankton (measured as chlorophyll α) explained the largest portion of the total variation in sedimentation loss rates (65% of P-flux, 57% of N-flux, 26% of total flux). In each case, systems with greater relative importance of autotrophic picoplankton had significantly reduced loss rates. In contrast, greater numbers of planktonic bacteria were associated with increased sedimentation rates and lower system efficiency. We suggest that different microbial components may have contrasting effects on the presumed enhanced efficiency provided by the microbial loop.

Concentration, size, and density of total suspended particulates at the air exhaust of concentrated animal feeding operations.

PubMed

Yang, Xufei; Lee, Jongmin; Zhang, Yuanhui; Wang, Xinlei; Yang, Liangcheng

2015-08-01

Total suspended particulate (TSP) samples were seasonally collected at the air exhaust of 15 commercial concentrated animal feeding operations (CAFOs; including swine finishing, swine farrowing, swine gestation, laying hen, and tom turkey) in the U.S. Midwest. The measured TSP concentrations ranged from 0.38 ± 0.04 mg m⁻³ (swine gestation in summer) to 10.9 ± 3.9 mg m⁻³ (tom turkey in winter) and were significantly affected by animal species, housing facility type, feeder type (dry or wet), and season. The average particle size of collected TSP samples in terms of mass median equivalent spherical diameter ranged from 14.8 ± 0.5 µm (swine finishing in winter) to 30.5 ± 2.0 µm (tom turkey in summer) and showed a significant seasonal effect. This finding affirmed that particulate matter (PM) released from CAFOs contains a significant portion of large particles. The measured particle size distribution (PSD) and the density of deposited particles (on average 1.65 ± 0.13 g cm⁻³) were used to estimate the mass fractions of PM10 and PM2.5 (PM ≤ 10 and ≤ 2.5 μm, respectively) in the collected TSP. The results showed that the PM10 fractions ranged from 12.7 ± 5.1% (tom turkey) to 21.1 ± 3.2% (swine finishing), whereas the PM2.5 fractions ranged from 3.4 ± 1.9% (tom turkey) to 5.7 ± 3.2% (swine finishing) and were smaller than 9.0% at all visited CAFOs. This study applied a filter-based method for PSD measurement and deposited particles as a surrogate to estimate the TSP's particle density. The limitations, along with the assumptions adopted during the calculation of PM mass fractions, must be recognized when comparing the findings to other studies.

Tailpipe, resuspended road dust, and brake-wear emission factors from on-road vehicles

NASA Astrophysics Data System (ADS)

Abu-Allaban, Mahmoud; Gillies, John A.; Gertler, Alan W.; Clayton, Russ; Proffitt, David

Intensive mass and chemical measurements were performed at roadside locations in Reno, Nevada, and Durham/Research Triangle Park), North Carolina to derive tailpipe, resuspended road dust, and brake-wear emission factors from in-use vehicles. Continuous particulate matter (PM) data were utilized to derive total emission factors while integrated PM data were used to attribute the calculated emission factors to different mechanisms using chemical mass balance receptor modeling and scanning electron microscopy techniques. Resuspended road dust and tailpipe emissions were found to be the dominant mechanisms that contribute significantly to the total PM 10 and PM 2.5 emission factors, respectively. Small contributions from brake-wear were observed at locations where strong braking occurs, but no tire-wear was seen at any sampling location. PM 10 emission rates from light-duty spark ignition (LDSI) vehicles ranged from 40 to 780 mg/km, 10 to 70 mg/km, and 0 to 80 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 10 emission rates from heavy-duty vehicles ranged from 230 to 7800 mg/km, 60 to 570 mg/km, and 0 to 610 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from LDSI vehicles ranged from 2 to 25 mg/km, 10 to 50 mg/km, and 0 to 5 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from heavy-duty vehicles ranged from 15 to 300 mg/km, 60 to 480 mg/km, and 0 to 15 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively.

Antioxidant Diet Protects Against Emphysema, but Increases Mortality in Cigarette Smoke-Exposed Mice

PubMed Central

Nyunoya, Toru; March, Thomas H.; Tesfaigzi, Yohannes; Seagrave, JeanClare

2012-01-01

Oxidative stress plays an important role in cigarette smoke-induced lung inflammation and emphysema. We produced an enriched diet by adding freeze-dried fruits and vegetables and additional supplements to the 8604 Teklad Rodent Diet, a standard rodent diet. In this study, we examined the effects of the antioxidant-enriched diet on cigarette smoke-induced lung inflammation and emphysema. CH3/HeN mice were fed either a regular diet or an antioxidant diet. These mice were exposed to filtered air, a low concentration of cigarette smoke (total particulate matter: 100 mg/m3) or a high concentration of cigarette smoke (total particulate matter: 250mg/m3) for 6 hours/day, 5 days/week for total 16 weeks. Surprisingly, increased mortality (53%) was observed in the high concentration of cigarette smoke-exposed mice fed the antioxidant diet compared to the high concentration of cigarette smoke-exposed mice that were fed a regular diet (13%). The necropsy analysis revealed nasal passage obstruction due to mucous plugging in cigarette smoke-exposed mice on the antioxidant diet. However, the antioxidant diet significantly reduced neutrophilic inflammation and emphysema in the high concentration of cigarette smoke-exposed mice as compared to the regular diet /high concentration of cigarette smoke controls. The antioxidant capacity in the bronchoalveolar fluid or oxidative damage to the lung tissue was not affected by the antioxidant diet. Pro-MMP-2, MMP-2, and MMP-9 activity did not correlate with the protective effects of AOD on cigarette smoke-induced emphysema. These data suggest that the antioxidant diet reduced cigarette smoke -induced inflammation and emphysema, but increased mortality in the obligate nose-breathing mice. PMID:21834692

Carbon speciation and surface tension of fog

USGS Publications Warehouse

Capel, P.D.; Gunde, R.; Zurcher, F.; Giger, W.

1990-01-01

The speciation of carbon (dissolved/particulate, organic/inorganic) and surface tension of a number of radiation fogs from the urban area of Zurich, Switzerland, were measured. The carbon species were dominated by "dissolved" organic carbon (DOC; i.e., the fraction that passes through a filter), which was typically present at levels of 40-200 mg/L. Less than 10% of the DOC was identified as specific individual organic compounds. Particulate organic carbon (POC) accounted for 26-41% of the mass of the particles, but usually less than 10% of the total organic carbon mass. Inorganic carbon species were relatively minor. The surface tensions of all the measured samples were less than pure water and were correlated with their DOC concentrations. The combination of high DOC and POC and low surface tension suggests a mechanism for the concentration of hydrophobic organic contaminants in the fog droplet, which have been observed by numerous investigators. ?? 1990 American Chemical Society.

Concentration Levels of Particulate Matter of Common Dental Lab Materials in a Military Dental Lab

DTIC Science & Technology

2016-05-01

to cause contact type dermatitis in some dental laboratory technicans. 22 In both experimental animals and humans, methyl methacrylate is rapidly...being measured out and mixed. As cases of generalized neuropathy, asthma and contact dermatitis have been documented in dental laboratory technicians... contact .45 The sampling for paraffin wax particulate in the current study resulted in a REL 8-TWA of 0.2056 mg/m 3 which is well below the 2 mg/m 3

Dissolved and particulate Barium in the Ganga (Hooghly) River estuary, India: Solute-particle interactions and the enhanced dissolved flux to the oceans

NASA Astrophysics Data System (ADS)

Samanta, Saumik; Dalai, Tarun K.

2016-12-01

In this study, the sources and the cycling of Ba have been evaluated in the Ganga (Hooghly) River estuary using the composition of the suspended sediments and the water samples collected during six seasons of contrasting water discharge over two years (2012 and 2013). In addition, the data on the samples of groundwater from areas adjacent to the estuary, and the industrial effluent water and urban wastewater draining into the estuary are presented. Selective extraction experiments were also performed on the suspended particulate matter of two seasons to assess the distribution of exchangeable concentrations of major ions and Ba. In the mixing zone, the variation patterns of the dissolved Ba concentrations show mid-salinity maxima and are similar to the patterns of variation of the particulate Mg/Al and Mg/Fe, suggesting that the production of dissolved Ba is linked to the adsorption of major ions on to the clay minerals and Fe-Mn oxyhydroxides in the particulate matter. The inference of coupled adsorption-desorption processes is supported by the observations that the particulate Ba/Mg and Ba/K ratios exhibit significant to strong negative correlations with the concentrations of Al, Fe and Mn. The observations of mid-salinity maxima for the concentrations of exchangeable Mg and K, and of the exchangeable Ba concentrations that decrease with salinity provide strong evidence that the solute-particle interactions is the major driver in regulating the dissolved Ba distributions in the estuary. The estimates of the quantity of desorbed Ba based on three different approaches suggest that desorption is sufficient to account for the calculated excess Ba (Baxs) concentrations. The contribution of Ba to the dissolved load via dissolution of the particulate carbonate phases is minor, up to 3% of the maximum Baxs concentrations. The estimates of anthropogenic contributions are insignificant, and account for ⩽2% of maximum Baxs in the estuary. Groundwater contributions are less significant and account for up to 5% of the annual Ba flux from the Hooghly estuary. The estimates of Ba flux show that annually (1.5-1.9) × 107 moles of Ba is transported by the Hooghly River. About (3.6-4.3) × 107 moles of Ba is generated annually in the estuary through desorption. Added together, the desorbed and riverine Ba fluxes generate a total Ba flux of (5.1-6.2) × 107 moles per year. Thus, the solute-particle interactions enhance the riverine Ba flux by >300%. A compilation of the available data shows that the enhancement of the riverine Ba flux and the fractions of desorbed Ba flux scale with (particulate matter flux/water flux) ratio in several estuaries of the world, suggesting that the process of solute-particle interactions is a major driver for the estuarine production of Ba on a global scale. Among the rivers considered in this study, the estuaries of the Hooghly River and the Ganges-Brahmaputra rivers, characterized by very high (sediment flux/water flux) ratio, depict the highest increase in the riverine Ba flux. This unique feature of the Ganga River system is inferred to be resulting from the collective impact of the tectonic activity and the monsoonal rainfall in the catchment areas.

Cardiovascular changes in workers exposed to fine particulate dust.

PubMed

Bortkiewicz, Alicja; Gadzicka, Elżbieta; Stroszejn-Mrowca, Grażyna; Szyjkowska, Agata; Szymczak, Wiesław; Koszada-Włodarczyk, Wiesława; Szadkowska-Stańczyk, Irena

2014-01-01

Epidemiological studies provide evidence that airborne particulate matter may contribute to the increased incidence and mortality rates due to pulmonary and cardiovascular diseases. Only some of them address the problem of occupational exposure to particulate air pollution. The aim of our study was to assess cardiovascular reaction and autonomic regulation in workers exposed to fine particles. All workers had medical examination, resting ECG with heart rate variability analysis (HRV), 24-h ECG, and ambulatory blood pressure monitoring (ABPM) performed. The subjects were 20 male workers (mean age: 32.14.0 year) of a ceramic ware factory exposed to the dust and 20 workers who were not exposed (mean age: 39.4±7.8 year). The period of employment under exposure amounted to 5.6±2.1 year. Dust exposure was measured using individual dosimeters. The geometric mean total dust concentration was 44±1.5 mg/m(3) and the FPD (fine particulate dust) concentration amounted to 11.5±1.6 mg/m(3). No abnormalities were noted in the resting ECG in both groups, in 24-h ECG 2 subjects, both from exposed and control groups, had ventricular heart rhythm and repolarization disturbances. Blood pressure in ABPM, both systolic as well as diastolic, was normal and did not differ between the groups. Resting heart rate in the exposed group was significantly lower (p = 0.038) than in the control group. In the exposed group STD R-R from short-term records was significantly higher (p = 0.01). Fast Fourier Transform (FFT) analysis showed that the low frequency power spectrum (LF) did not differ in the exposed and the control group, while high frequency (HF) was significantly higher in the exposed group. LF/HF ratio was significantly lower in the exposed in comparison with the control group. Although we did not reveal significant abnormalities in ECG as well as in ABPM in the exposed group, it seems that neurovegetative disturbances (parasympathetic predominance) may serve as an early indicator of fine particulate dust effect on cardiovascular system.

Evaluation of environmental effect of coal stockpile in Muara Telang, Banyuasin, Indonesia

NASA Astrophysics Data System (ADS)

Rusdianasari; Arita, Susila; Ibrahim, Eddy; Ngudiantoro

2013-04-01

Stockpile commonly serves as a temporary dump before the coal is transported through the waterways. This study investigated the effects of coal stockpiles on the surrounding environment: air, water, and soil. The location of the study is in the estuary of Telang, South-Sumatra, Indonesia, which is located at the edge of the river of Telang and close to the residential community. The monitoring of the environmental impact from the stockpile is intended to conduct an environmental assessment owing the existence and operations of coal accumulation. Enviromental impact analysis was conducted based on the value of the effluent, air pollution (dust), soil and water by determining the parameters of the coal wastewater pH, total suspended solid, ferrous dan ferrous metals contents. The results indicate that the total suspended particulate, total suspended solids, noise level, ferrous metal and manganese metal were 10-14 μg/Nm3 249-355 mg/L, 41.3 to 50.3 dBA, 6.074 to7.579 mg/L, and 1.987 to 2.678 mg/L, respectively. Meanwhile the pH of water and soil were 3 to 4 and 2.83 to 4.02 respectively. It is concluded that the pH value are beyond the threshold standard.

Long-term observation of particulate barium fluxes in the subtropical Northeast Atlantic (33 N, 22 W)

NASA Astrophysics Data System (ADS)

Stern, Judith; Dellwig, Olaf; Waniek, Joanna J.

2017-04-01

Particle flux material was collected with a sediment trap in 2000 m depth of the deep-sea mooring Kiel 276. The mooring is located in the oligotrophic subtropical NE Atlantic (33˚ N, 22˚ W), which is influenced by the Azores Current and its associated front and lithogenic particle inputs via atmospheric transport pathways. Total barium fluxes and biogenic barium (Babio) fluxes between 2002 and 2008, calculated on the basis of Ba amounts measured with ICP-OES (inductively coupled plasma optical emission spectrometry), are demonstrated in this study. The behavior of (biogenic) barium in the deep-sea is of great interest because it is used as a proxy for surface ocean productivity. Nevertheless, formation and transport mechanisms of particulate Ba, especially barite, in the oceans are still under debate. Especially, long-term Ba flux studies demonstrating inter and intra annual variability are missing. To fill this gap we used time-series measurements of Ba fluxes observed at Kiel 276 to demonstrate the variability of particulate Ba formation and transport. Total Ba fluxes and Babio fluxes at the mooring are characterized by flux pattern attributed to the behavior of the total particle flux. The particle flux is highly variable with peak fluxes up to 365 mg m-2 d-1 during winter and early spring just after highest primary production (winter bloom of coccolithophores) and maximum dust concentration in the atmosphere occurred. The Babioflux (up to 97 % of the total Ba flux) is influenced by productivity but also by the position of the Azores Front leading to a clear reduced Babio flux from 2005 onwards related to changes in shape and size of the catchment area of the sediment trap and reduced productivity due to lower nutrient availability. We observed a close connection of Babio flux and Ca flux results from incorporation of Ba in biogenic CaCO3 and from the formation of aggregates including Ba-bearing particles like barite and biogenic CaCO3. The transport of particulate Ba seems to be mainly driven by the formation of aggregates in the water column.

Respirator use and its impact on particulate matter exposure in aluminum manufacturing facilities.

PubMed

Liu, Sa; Noth, Elizabeth; Eisen, Ellen; Cullen, Mark R; Hammond, Katharine

2018-05-31

Objectives As part of a large epidemiologic study of particulate health effect, this study aimed to report respirator use among total particulate matter (TPM) samples collected in a major aluminum manufacturing company from 1966‒2013 and evaluate the impact of respirator-use adjustment on exposure estimation. Methods Descriptive analyses were performed to evaluate respirator use across facilities and by facility type and job. Protection factors were applied to TPM measurements for recorded respirator use. Estimated TPM exposure for each job ‒ before and after respirator-use adjustment ‒ were compared to assess the impact of adjustment on exposure estimation. Results Respirator use was noted for 37% of 12 402 full-shift personal TPM samples. Measured TPM concentration ranged from less than detectable to 8220 mg/m3, with arithmetic mean, median and standard deviation being 10.6, 0.87 and 130 mg/m 3 , respectively. Respirators were used more often in smelting facilities (52% of TPM measurements) than in fabricating (17%) or refinery facilities (28%) (P<0.01). Sixty-two percent of jobs in smelting facilities were subject to respirator-use adjustment, whereas it was 20% and 70% in fabricating and refinery facilities, respectively. Applying protection factors to TPM measurements significantly reduced estimated job mean TPM exposures and changed exposure categories in these facilities, with larger impact in smelting than fabricating facilities. Conclusions Respirator use varied by time, facility and job. Adjusting respirator use resulted in differential impact in smelting and fabricating facilities, which will need to be incorporated into ongoing epidemiologic studies accordingly.

Health hazard evaluation report HETA 85-060-1670, City of Norwood, Norwood, Ohio. [Toner powder exposure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruhe, R.L.; Bennett, D.

1986-02-01

Following a request from the Health Commissioner of Norwood, Ohio, employee exposure to toner powder used in Norwood Senior High Media Center photocopying machine was investigated. Personal and area air samples for total particulates were collected on preweighed filters and total sample weights determined. Indicator tube sampling was done for carbon monoxide and ozone. Medical interviews were conducted with three media center workers to elicit work related symptomatology. Exposure to total particulate ranged from less than the detection limit to 0.02 mg/m/sup 3/. Carbon monoxide and ozone were nondetectable. Two employees reported no symptoms associated with work. After operating themore » copy machine for 3 weeks, the third employee developed hives on both hands progressing to the earlobes and right cheek. Her condition improved on weekends. She also had a cough and shortness of breath when working with the duplicator. No positive response to patch testing was seen, but the employee developed cough, tearing eyes, and itching 2 hours after patch application. The authors conclude that one employee suffered an allergic reaction precipitated by materials inhaled in the duplicator area. It is recommended that this employee not use this machine, and improved ventilation be provided for the entire media center.« less

The efficiency of solvent extraction of mutagenic compounds in particulates exhausted from a small diesel engine.

PubMed

Tahara, I; Kinouchi, T; Kataoka, K; Ohnishi, Y

1994-06-01

Organic materials were extracted from particulates exhausted from a small diesel engine (displacement 269 ml) by the ultrasonic extraction method with three different solvent systems, methanol, dichloromethane and a 4:1 (v:v) mixture of benzene and ethanol. These solvent-extracted materials were tested for mutagenic activity by the Ames Salmonella/microsome assay system using Salmonella typhimurium strains TA98, TA100, TA98NR and TA98/1,8-DNP6. The concentrations of 1-nitropyrene (1-NP) and 1,6-dinitropyrene (1,6-diNP) in these extracted materials were also measured after nitroreduction by high pressure liquid chromatography. The methanol-extracted and benzene-ethanol-extracted materials showed the lowest and the highest mutagenic activity, respectively. The methanol-extracted, dichloromethane-extracted and benzene-ethanol-extracted materials induced 260, 1,570 and 3,240 His+ revertants per plate per mg of extracted materials, respectively, from strain TA98 in the absence of S9 mix. These materials showed decreased mutagenicity for strains TA98NR and TA98/1,8-DNP6, indicating that the particulates in the diesel engine exhaust contained 1-NP and diNPs. Actually, the amount of 1-NP and 1,6-diNP in the methanol-extracted, dichloromethane-extracted and benzene-ethanol-extracted materials were 17.0 and 0.03 ng, 37.5 and 0.97 ng, and 71.3 and 1.03 ng per mg of extracted materials, respectively, accounting for 11.9 and 3.2%, 4.4 and 17.3%, and 4.0 and 8.9%, respectively, of the total mutagenicity of the extracted materials. From these results it is concluded that a mixture of benzene-ethanol (4:1, v/v) is the most suitable solvent for extraction of organic matter containing nitrated polycyclic aromatic hydrocarbons such as NPs from particulates in diesel engine exhaust.

Total suspended particulate matter and toxic elements indoors during cooking with yak dung

NASA Astrophysics Data System (ADS)

Kang, Shichang; Li, Chaoliu; Wang, Feiyue; Zhang, Qianggong; Cong, Zhiyuan

Many herders in the Tibetan Plateau still inherit the traditional lifestyle, including living in tents and burning yak dung for fuel. This short correspondence reports a pilot study on indoor air quality in the nomadic tents in the Nam Co region, inland Tibetan Plateau. The results showed very high concentrations of total suspended particles (TSP), averaging at 4.45 mg m -3 during the cooking/heating period (with daily value of 3.16 mg m -3). Elevated concentrations of toxic element Cd, As and Pb were also found within the tents, averaging 3.16 μg m -3, 35.00 μg m -3, and 81.39 μg m -3 for a day, respectively, which were not only far higher than those of WHO indoor air quality guidelines, but also more than 10 4-10 6 times higher than the outdoor air level in the Nam Co area. The study raises serious concerns over the health of Tibetan herders following their long-term exposure to the tent air.

Environmental assessment of a wood-waste-fired industrial watertube boiler. Volume 1. Technical results. Final report, March 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.

1987-03-01

The two-volume report gives results from field tests of a wood-waste-fired industrial watertube boiler. Two series of tests were performed: one firing dry (11% moisture) wood waste, and the other firing green (34% moisture) wood waste. Emission measurements included: continuous monitoring of flue-gas emissions; source-assessment sampling system (SASS) sampling of the flue gas with subsequent laboratory analysis of samples to give total flue-gas organics in two boiling-point ranges, compound category information within these ranges, specific quantitation of the semi-volatile organic priority pollutants, and flue-gas concentrations of 73 trace elements; Method 5 sampling for particulate; controlled condensation system sampling for SO/submore » 2/ and SO/sub 3/; and grab sampling of boiler mechanical collector hopper ash for inorganic composition determinations. Total organic emissions decreased from 60-135 mg/dscm firing dry wood to 2-65 mg/dscm firing green wood, in parallel with corresponding boiler CO emissions.« less

Environmental assessment of a wood-waste-fired industrial watertube boiler. Volume 2. Data supplement. Final report, March 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.

1987-03-01

The two-volume report gives results from field tests of a wood-waste-fired industrial watertube boiler. Two series of tests were performed: one firing dry (11% moisture) wood waste, and the other firing green (34% moisture) wood waste. Emission measurements included: continuous monitoring of flue-gas emissions; source-assessment sampling system (SASS) sampling of the flue-gas with subsequent laboratory analysis of samples to give total flue-gas organics in two boiling-point ranges, compound category information within these ranges, specific quantitation of the semi-volatile organic priority pollutants, and flue gas concentrations of 73 trace elements; Method 5 sampling for particulate; controlled condensation system sampling for SO/submore » 2/ and SO/sub 3/; and grab sampling of boiler mechanical collector hopper ash for inorganic and organic composition determinations. Total organic emissions decreased from 60-135 mg/dscm firing dry wood to 2-65 mg/dscm firing green wood, in parallel with corresponding boiler CO emissions.« less

Particulates generated from combustion of polymers (plastics).

PubMed

Shemwell, B E; Levendis, Y A

2000-01-01

This is an experimental study on the characterization of particulate (soot) emissions from burning polymers. Emissions of polystyrene (PS), polyethylene (PE), polypropylene (PP), polymethyl methacrylate (PMMA), and polyvinyl chloride (PVC) plastics were studied. Combustion took place in a laboratory-scale, electrically heated, drop-tube furnace at temperatures of 1300 and 1500 K, in air. The nominal bulk (global) equivalence ratio, phi, was varied in the range of 0.5-1.5, and the gas residence time in the nearly isothermal radiation zone of the furnace was approximately 1 sec. The particulate emissions were size-classified at the exit of the furnace, using a multi-stage inertial particle impactor. Results showed that both the yields and the size distributions of the emitted soot were remarkably different for the five plastics burned. Soot yields increased with an increasing bulk equivalence ratio. Combustion of PS yielded the highest amounts of soot (most highly agglomerated), several times more than the rest of the polymers. More soot was emitted from PS at 1500 than at 1300 K. Substantial amounts of soot agglomerates were larger than 9 microns. At 1500 and 1300 K, 35 and 29% of the soot mass, respectively, was PM2 (2 microns or smaller). Emissions from PE and PP were remarkably similar to each other. These polymers produced very low emissions at phi < or = 0.5, but emissions increased drastically with phi, and most of the soot was very fine (70-97% of the mass was PM2, depending on phi). Emissions from the combustion of PMMA were comparatively low and were the least influenced by the bulk phi, and 79-95% of the emissions were PM2. Combustion of PVC yielded the lowest amounts of soot; moreover, only 13-34% of the mass was PM2. On a comparative basis, at 1500 K, the following ranges of particulate yields were PM2: 19-75 mg/g of PS, 8-36 mg/g of PE, 1.5-47 mg/g of PP, 11-20 mg/g of PMMA, and 2-8 mg/g of PVC, depending on phi. These comparative results demonstrate that PS produces the highest amounts of fine particulates, followed by PP, PE, and PMMA, and then PVC. Burning these materials with excess oxygen drastically reduces the particulate emissions of PE and PP, substantially reduces those of PS, and mildly reduces those of PMMA and PVC.

Size charge fractionation of metals in municipal solid waste landfill leachate.

PubMed

Oygard, Joar Karsten; Gjengedal, Elin; Røyset, Oddvar

2007-01-01

Municipal solid waste landfill leachates from 9 Norwegian sites were size charge fractionated in the field, to obtain three fractions: particulate and colloidal matter >0.45microm, free anions/non-labile complexes <0.45microm and free cations/labile complexes <0.45microm. The fractionation showed that Cd and Zn, and especially Cu and Pb, were present to a large degree (63-98%) as particulate and colloidal matter >0.45microm. Cr, Co and Ni were on the contrary present mostly as non-labile complexes (69-79%) <0.45microm. The major cations Ca, Mg, K, and Mn were present mainly as free cations/labile complexes <0.45microm, while As and Mo were present to a large degree (70-90%) as free anions/non-labile complexes <0.45microm. Aluminium was present mainly as particulate and colloidal matter >0.45microm. The particulate and colloidal matter >0.45microm was mainly inorganic; indicating that the metals present in this fraction were bound as inorganic compounds. The fractionation gives important information on the mobility and potential bioavailability of the metals investigated, in contrast to the total metal concentrations usually reported. To study possible changes in respective metal species in leachate in aerated sedimentation tanks, freshly sampled leachate was stored for 48h, and subsequently fractionated. This showed that the free heavy metals are partly immobilized during storage of leachate with oxygen available. The largest effects were found for Cd and Zn. The proportion of As and Cr present as particulate matter or colloids >0.45microm also increased.

Short-term effects of particulate matter constituents on daily hospitalizations and mortality in five South-European cities: results from the MED-PARTICLES project.

PubMed

Basagaña, Xavier; Jacquemin, Bénédicte; Karanasiou, Angeliki; Ostro, Bart; Querol, Xavier; Agis, David; Alessandrini, Ester; Alguacil, Juan; Artiñano, Begoña; Catrambone, Maria; de la Rosa, Jesús D; Díaz, Julio; Faustini, Annunziata; Ferrari, Silvia; Forastiere, Francesco; Katsouyanni, Klea; Linares, Cristina; Perrino, Cinzia; Ranzi, Andrea; Ricciardelli, Isabella; Samoli, Evangelia; Zauli-Sajani, Stefano; Sunyer, Jordi; Stafoggia, Massimo

2015-02-01

Few recent studies examined acute effects on health of individual chemical species in the particulate matter (PM) mixture, and most of them have been conducted in North America. Studies in Southern Europe are scarce. The aim of this study is to examine the relationship between particulate matter constituents and daily hospital admissions and mortality in five cities in Southern Europe. The study included five cities in Southern Europe, three cities in Spain: Barcelona (2003-2010), Madrid (2007-2008) and Huelva (2003-2010); and two cities in Italy: Rome (2005-2007) and Bologna (2011-2013). A case-crossover design was used to link cardiovascular and respiratory hospital admissions and total, cardiovascular and respiratory mortality with a pre-defined list of 16 PM10 and PM2.5 constituents. Lags 0 to 2 were examined. City-specific results were combined by random-effects meta-analysis. Most of the elements studied, namely EC, SO4(2-), SiO2, Ca, Fe, Zn, Cu, Ti, Mn, V and Ni, showed increased percent changes in cardiovascular and/or respiratory hospitalizations, mainly at lags 0 and 1. The percent increase by one interquartile range (IQR) change ranged from 0.69% to 3.29%. After adjustment for total PM levels, only associations for Mn, Zn and Ni remained significant. For mortality, although positive associations were identified (Fe and Ti for total mortality; EC and Mg for cardiovascular mortality; and NO3(-) for respiratory mortality) the patterns were less clear. The associations found in this study reflect that several PM constituents, originating from different sources, may drive previously reported results between PM and hospital admissions in the Mediterranean area. Copyright © 2014 Elsevier Ltd. All rights reserved.

Stable isotope studies of nicotine kinetics and bioavailability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benowitz, N.L.; Jacob, P. 3d.; Denaro, C.

1991-03-01

The stable isotope-labeled compound 3',3'-dideuteronicotine was used to investigate the disposition kinetics of nicotine in smokers, the systemic absorption of nicotine from cigarette smoke, and the bioavailability of nicotine ingested as oral capsules. Blood levels of labeled nicotine could be measured for 9 hours after a 30-minute intravenous infusion. Analysis of disposition kinetics in 10 healthy men revealed a multiexponential decline after the end of an infusion, with an elimination half-life averaging 203 minutes. This half-life was longer than that previously reported, indicating the presence of a shallow elimination phase. Plasma clearance averaged 14.6 ml/min/kg. The average intake of nicotinemore » per cigarette was 2.29 mg. A cigarette smoke-monitoring system that directly measured particulate matter in smoke was evaluated in these subjects. Total particulate matter, number of puffs on the cigarette, total puff volume, and time of puffing correlated with the intake of nicotine from smoking. The oral bioavailability of nicotine averaged 44%. This bioavailability is higher than expected based on the systemic clearance of nicotine and suggests that there may be significant extrahepatic metabolism of nicotine.« less

Particulate sulphate and ozone in rural air: Preliminary results from three sites in central England

NASA Astrophysics Data System (ADS)

Martin, A.; Barber, F. R.

Daily particulate sulphate concentrations in air have been measured at a 'background' rural site and at two other sites near rural power stations. The samples were collected by drawing air through filter papers and were analysed by X-ray fluorescence. At the background site the concentration of particulate sulphates was strongly dependent on the O 3 and total S in air. Above a certain 'critical' level of daily O 3, 28% of the daily S in air was particulate on average, but the amounts were not related to the actual O 3 levels. At lower O 3 levels, there appeared to be a constant background of about 2 μg of particulate sulphate per cubic meter of air, together with about 5% of the total S in air as particulate. When black smoke in air was low, the particulate sulphate was also low, despite the O 3 levels. Near the power stations, there was no significantly different rate of production or loss of particulate sulphate. On average, at all three sites over the year, about 12% of the daily total S was particulate, probably corresponding to an average conversion rate of SO 2 of less than 1% per hour. Estimates of hourly particulate sulphates are available from previous measurements at the background site, using a different analysis technique. Particulate sulphate was not found every hour, but typically during 20 h a day in early summer and 8 h a day in early winter. An influence of humidity as well as O 3 was apparent in the peak hourly particulate sulphate values, which reached 60% of the total S. No correlation could be found of particulate sulphate with solar radiation, wind direction, concentrations of oxides of nitrogen in air or ammonium or sulphate in rainwater, but further measurements are planned.

Compatibility and Stability of Rolapitant Injectable Emulsion Admixed with Dexamethasone Sodium Phosphate.

PubMed

Wu, George; Yeung, Stanley; Chen, Frank

2017-01-01

Neurokinin-1 receptor antagonist, 5-hydroxytryptamine-3 receptor antagonist, and dexamethasone combination therapy is the standard of care for the prevention of chemotherapy-induced nausea and vomiting. Herein, we describe the physical and chemical stability of an injectable emulsion of the Neurokinin-1 receptor antagonist rolapitant 185 mg in 92.5 mL (free base, 166.5 mg in 92.5 mL) admixed with either 2.5 mL of dexamethasone sodium phosphate (10 mg) or 5 mL of dexamethasone sodium phosphate (20 mg). Admixtures were prepared and stored in two types of container closures (glass and Crystal Zenith plastic bottles) and four types of intravenous administration tubing sets (or intravenous tubing sets). The assessment of the physical and chemical stability was conducted on admixtures packaged in bottled samples stored at room temperature (20°C to 25°C under fluorescent light) and evaluated at 0, 1, and 6 hours. For admixtures in intravenous tubing sets, the assessment of physicochemical stability was performed after 0 and 7 hours of storage at 20°C to 25°C, and then after 20 hours (total 27 hours) under refrigeration (2°C to 8°C) and protected from light. Physical stability was assessed by visually examining the bottle contents under normal room light and measuring turbidity and particulate matter. Chemical stability was assessed by measuring the pH of the admixture and determining drug concentrations through high-performance liquid chromatographic analysis. Results showed that all samples were physically compatible throughout the duration of the study. The admixtures stayed within narrow and acceptable ranges in pH, turbidity, and particulate matter. Admixtures of rolapitant and dexamethasone were chemically stable when stored in glass and Crystal Zenith bottles for at least 6 hours at room temperature, as well as in the four selected intravenous tubing sets for 7 hours at 20°C to 25°C and then for 20 (total 27 hours) hours at 2°C to 8°C. No loss of potency of any admixed component occurred in the samples stored at the temperature ranges studied. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

Contrasting seasonality in optical-biogeochemical properties of the Baltic Sea.

PubMed

Simis, Stefan G H; Ylöstalo, Pasi; Kallio, Kari Y; Spilling, Kristian; Kutser, Tiit

2017-01-01

Optical-biogeochemical relationships of particulate and dissolved organic matter are presented in support of remote sensing of the Baltic Sea pelagic. This system exhibits strong seasonality in phytoplankton community composition and wide gradients of chromophoric dissolved organic matter (CDOM), properties which are poorly handled by existing remote sensing algorithms. Absorption and scattering properties of particulate matter reflected the seasonality in biological (phytoplankton succession) and physical (thermal stratification) processes. Inherent optical properties showed much wider variability when normalized to the chlorophyll-a concentration compared to normalization to either total suspended matter dry weight or particulate organic carbon. The particle population had the largest optical variability in summer and was dominated by organic matter in both seasons. The geographic variability of CDOM and relationships with dissolved organic carbon (DOC) are also presented. CDOM dominated light absorption at blue wavelengths, contributing 81% (median) of the absorption by all water constituents at 400 nm and 63% at 442 nm. Consequentially, 90% of water-leaving radiance at 412 nm originated from a layer (z90) no deeper than approximately 1.0 m. With water increasingly attenuating light at longer wavelengths, a green peak in light penetration and reflectance is always present in these waters, with z90 up to 3.0-3.5 m depth, whereas z90 only exceeds 5 m at biomass < 5 mg Chla m-3. High absorption combined with a weakly scattering particle population (despite median phytoplankton biomass of 14.1 and 4.3 mg Chla m-3 in spring and summer samples, respectively), characterize this sea as a dark water body for which dedicated or exceptionally robust remote sensing techniques are required. Seasonal and regional optical-biogeochemical models, data distributions, and an extensive set of simulated remote-sensing reflectance spectra for testing of remote sensing algorithms are provided as supplementary data.

Progression of soot cake layer properties during the systematic regeneration of diesel particulate filters measured with neutron tomography

DOE PAGES

Toops, Todd J.; Pihl, Josh A.; Finney, Charles E. A.; ...

2015-01-16

Although particulate filters (PFs) have been a key component of the emission control system for modern diesel engines, there remain significant questions about the basic regeneration behavior of the filters and how it changes with accumulation of increasing soot layers. This effort describes a systematic deposition and regeneration of particulate matter in 25-mm diameter × 76-mm long wall-flow PFs composed of silicon carbide (SiC) material. The initial soot distributions were analyzed for soot cake thickness using a nondestructive neutron imaging technique. With the PFs intact, it was then possible to sequentially regenerate the samples and reanalyze them, which was performedmore » after nominal 20, 50, and 70 % regenerations. The loaded samples show a relatively uniform distribution of particulate with an increasing soot cake thickness and nearly identical initial density of 70 mg/cm 3. Throughout regeneration, the soot cake thickness initially decreases significantly while the density increases to 80–90 mg/cm 3. After ~50 % regeneration, the soot cake thickness stays relatively constant, but instead, the density decreases as pores open up in the layer (~35 mg/cm 3 at 70 % regeneration). Here, complete regeneration initially occurs at the rear of the PF channels. With this information, a conceptual model of the regeneration is proposed.« less

Progression of soot cake layer properties during the systematic regeneration of diesel particulate filters measured with neutron tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toops, Todd J.; Pihl, Josh A.; Finney, Charles E. A.

Although particulate filters (PFs) have been a key component of the emission control system for modern diesel engines, there remain significant questions about the basic regeneration behavior of the filters and how it changes with accumulation of increasing soot layers. This effort describes a systematic deposition and regeneration of particulate matter in 25-mm diameter × 76-mm long wall-flow PFs composed of silicon carbide (SiC) material. The initial soot distributions were analyzed for soot cake thickness using a nondestructive neutron imaging technique. With the PFs intact, it was then possible to sequentially regenerate the samples and reanalyze them, which was performedmore » after nominal 20, 50, and 70 % regenerations. The loaded samples show a relatively uniform distribution of particulate with an increasing soot cake thickness and nearly identical initial density of 70 mg/cm 3. Throughout regeneration, the soot cake thickness initially decreases significantly while the density increases to 80–90 mg/cm 3. After ~50 % regeneration, the soot cake thickness stays relatively constant, but instead, the density decreases as pores open up in the layer (~35 mg/cm 3 at 70 % regeneration). Here, complete regeneration initially occurs at the rear of the PF channels. With this information, a conceptual model of the regeneration is proposed.« less

Comparison of three corrosion inhibitors in simulated partial lead service line replacements.

PubMed

Kogo, Aki; Payne, Sarah Jane; Andrews, Robert C

2017-05-05

Partial lead service line replacements (PLSLR) were simulated using five recirculating pipe loops treated with either zinc orthophosphate (1mg/L as P), orthophosphate (1mg/L as P) or sodium silicate (10mg/L). Two pipe loops served as ⿿inhibitor-free⿿ (Pb-Cu) and ⿿galvanic free⿿ (Pb-PVC) controls. Changes in water quality (CSMR [0.2 or 1], conductivity [⿿330mS/cm or ⿿560mS/cm], chlorine [1.4mg/L]) were not observed to provide a significant impact on lead or copper release, although galvanic corrosion was shown to be a driving factor. Generally, both orthophosphate and zinc orthophosphate provided better corrosion control for both total and dissolved lead (30min, 6h, 65h) and copper (30min, 6h), when compared to either the inhibitor-free control or the sodium silicate treated system. This work highlights the importance of understanding the complex interplay of corrosion inhibitors on particulate and dissolved species when considering both lead and copper. Copyright © 2017 Elsevier B.V. All rights reserved.

Study on effects of powder and flake chemistry and morphology on the properties of Al-Cu-Mg-X-X-X powder metallurgy advanced aluminum alloys

NASA Technical Reports Server (NTRS)

Meschter, P. J.; Lederich, R. J.; Oneal, J. E.; Pao, P. S.

1985-01-01

The effects of alloy chemistry and particulate morphology on consolidation behavior and consolidated product properties in rapid solidification processed, powder-metallurgical Al-3Li-1.5Cu-1Mg-0.5Co-0.2Zr and Al-4.4Cu-1.5Mg-Fe-Ni-0.2Zr extrusions and forgings were studied. Microstructures and mechanical properties of both alloys are largely unaffected by particulate production method (vacuum atomization, ultrasonic atomization, or twin-roller quenching) and by particulate solidification rates between 1000 and 100,000 K/s. Consolidation processing by canning, cold compaction, degassing, and hot extrusion is sufficient to yield mechanical properties in the non-Li-containing alloy extrusions which are similar to those of 7075-Al, but ductilities and fracture toughnesses are inferior owing to poor interparticle bonding caused by lack of a vacuum-hot-pressing step during consolidation. Mechanical properties of extrusions are superior to those of forgings owing to the stronger textures produced by the more severe hot working during extrusion. The effects on mechanical properties of dispersoid size and volume fraction, substructural refinement, solid solution strengthening by Mg, and precipitate size and distribution are elucidated for both alloy types.

Assessing total nitrogen in surface-water samples--precision and bias of analytical and computational methods

USGS Publications Warehouse

Rus, David L.; Patton, Charles J.; Mueller, David K.; Crawford, Charles G.

2013-01-01

The characterization of total-nitrogen (TN) concentrations is an important component of many surface-water-quality programs. However, three widely used methods for the determination of total nitrogen—(1) derived from the alkaline-persulfate digestion of whole-water samples (TN-A); (2) calculated as the sum of total Kjeldahl nitrogen and dissolved nitrate plus nitrite (TN-K); and (3) calculated as the sum of dissolved nitrogen and particulate nitrogen (TN-C)—all include inherent limitations. A digestion process is intended to convert multiple species of nitrogen that are present in the sample into one measureable species, but this process may introduce bias. TN-A results can be negatively biased in the presence of suspended sediment, and TN-K data can be positively biased in the presence of elevated nitrate because some nitrate is reduced to ammonia and is therefore counted twice in the computation of total nitrogen. Furthermore, TN-C may not be subject to bias but is comparatively imprecise. In this study, the effects of suspended-sediment and nitrate concentrations on the performance of these TN methods were assessed using synthetic samples developed in a laboratory as well as a series of stream samples. A 2007 laboratory experiment measured TN-A and TN-K in nutrient-fortified solutions that had been mixed with varying amounts of sediment-reference materials. This experiment identified a connection between suspended sediment and negative bias in TN-A and detected positive bias in TN-K in the presence of elevated nitrate. A 2009–10 synoptic-field study used samples from 77 stream-sampling sites to confirm that these biases were present in the field samples and evaluated the precision and bias of TN methods. The precision of TN-C and TN-K depended on the precision and relative amounts of the TN-component species used in their respective TN computations. Particulate nitrogen had an average variability (as determined by the relative standard deviation) of 13 percent. However, because particulate nitrogen constituted only 14 percent, on average, of TN-C, the precision of the TN-C method approached that of the method for dissolved nitrogen (2.3 percent). On the other hand, total Kjeldahl nitrogen (having a variability of 7.6 percent) constituted an average of 40 percent of TN-K, suggesting that the reduced precision of the Kjeldahl digestion may affect precision of the TN-K estimates. For most samples, the precision of TN computed as TN-C would be better (lower variability) than the precision of TN-K. In general, TN-A precision (having a variability of 2.1 percent) was superior to TN-C and TN-K methods. The laboratory experiment indicated that negative bias in TN-A was present across the entire range of sediment concentration and increased as sediment concentration increased. This suggested that reagent limitation was not the predominant cause of observed bias in TN-A. Furthermore, analyses of particulate nitrogen present in digest residues provided an almost complete accounting for the nitrogen that was underestimated by alkaline-persulfate digestion. This experiment established that, for the reference materials at least, negative bias in TN-A was caused primarily by the sequestration of some particulate nitrogen that was refractory to the digestion process. TN-K biases varied between positive and negative values in the laboratory experiment. Positive bias in TN-K is likely the result of the unintended reduction of a small and variable amount of nitrate to ammonia during the Kjeldahl digestion process. Negative TN-K bias may be the result of the sequestration of a portion of particulate nitrogen during the digestion process. Negative bias in TN-A was present across the entire range of suspended-sediment concentration (1 to 14,700 milligrams per liter [mg/L]) in the synoptic-field study, with relative bias being nearly as great at sediment concentrations below 10 mg/L (median of -3.5 percent) as that observed at sediment concentrations up to 750 mg/L (median of -4.4 percent). This lent support to the laboratory-experiment finding that some particulate nitrogen is sequestered during the digestion process, and demonstrated that negative TN-A bias was present in samples with very low suspended-sediment concentrations. At sediment concentrations above 750 mg/L, the negative TN-A bias became more likely and larger (median of -13.2 percent), suggesting a secondary mechanism of bias, such as reagent limitation. From a geospatial perspective, trends in TN-A bias were not explained by selected basin characteristics. Though variable, TN-K bias generally was positive in the synoptic-field study (median of 3.1 percent), probably as a result of the reduction of nitrate. Three alternative approaches for assessing TN in surface water were evaluated for their impacts on existing and future sampling programs. Replacing TN-A with TN-C would remove the bias from subsequent data, but this approach also would introduce discontinuity in historical records. Replacing TN-K with TN-C would lead to the removal of positive bias in TN-K in the presence of elevated nitrate. However, in addition to the issues that may arise from a discontinuity in the data record, this approach may not be applicable to regulatory programs that require the use of total Kjeldahl nitrogen for stream assessment. By adding TN-C to existing TN-A or TN-K analyses, historical-data continuity would be preserved and the transitional period could be used to minimize the impact of bias on data analyses. This approach, however, imposes the greatest burdens on field operations and in terms of analytical costs. The variation in these impacts on different sampling programs will challenge U.S. Geological Survey scientists attempting to establish uniform standards for TN sample collection and analytical determinations.

Characterization of organic particulates present in milk factory process waters used for reuse along with aerobically digested effluent wastewater.

PubMed

Verheyen, Vincent; Cruickshank, Alicia; Wild, Karl; Heaven, Michael W; McGee, Rachel; Watkins, Mark; Nash, David

2011-01-01

Wastewater from a dairy processor is being reused and recycled both within the plant and for irrigation. Flash pyrolysis GC-MS was used to examine nitrogen and phenol containing compounds (M.W.=35 to 450 g/mol) in the particulate fraction of the milk condensate, combined clean wastewater and aerobic bioreactor effluent. For comparison, the particulates were also prepared for standard GC-MS analyses using conventional solvent extraction methods. Compounds detected by pyrolysis GC-MS were found mostly in the bioreactor with the amino acid arginine (220 mg/kg) and the amino acid derivative 1-methyl-5-oxo-L-proline methyl ester (130 mg/kg) found at the highest concentrations. In comparison, sterols detected in the effluent were found at higher concentrations when using solvent extraction indicating some degradation with pyrolysis GC-MS. However, with few exceptions, particulates were generally found not to act as passive collectors capable of concentrating less water soluble chemicals. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

Gravimetric wear analysis and particulate characterization of bilateral facet-augmentation system--PercuDyn™.

PubMed

Bhattacharya, Sanghita; Nayak, Aniruddh; Goel, Vijay K; Warren, Chris; Schlaegle, Steve; Ferrara, Lisa

2010-01-01

Dynamic stabilization systems are emerging as an alternative to fusion instrumentation. However, cyclic loading and micro-motion at various interfaces may produce wear debris leading to adverse tissue reactions such as osteolysis. Ten million cycles of wear test was performed for PercuDyn™ in axial rotation and the wear profile and the wear rate was mapped. A validation study was undertaken to assess the efficiency of wear debris collection which accounted for experimental errors. The mean wear debris measured at the end of 10 million cycles was 4.01 mg, based on the worst-case recovery rate of 68.2%. Approximately 40% of the particulates were less than 5 μm; 92% less than 10 μm. About 43% of particulates were spherical in shape, 27% particulates were ellipsoidal and the remaining particles were of irregular shapes. The PercuDyn™ exhibited an average polymeric wear rate of 0.4 mg/million cycles; substantially less than the literature derived studies for other motion preservation devices like the Bryan disc and Charité disc. Wear debris size and shape were also similar to these devices.

Chemopreventive activity of compounds extracted from Casearia sylvestris (Salicaceae) Sw against DNA damage induced by particulate matter emitted by sugarcane burning near Araraquara, Brazil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prieto, A.M.; Santos, A.G.; Csipak, A.R.

Ethanolic extract of Casearia sylvestris is thought to be antimutagenic. In this study, we attempted to determine whether this extract and casearin X (a clerodane diterpene from C. sylvestris) are protective against the harmful effects of airborne pollutants from sugarcane burning. To that end, we used the Tradescantia micronucleus test in meiotic pollen cells of Tradescantia pallida, the micronucleus test in mouse bone marrow cells, and the comet assay in mouse blood cells. The mutagenic compound was total suspended particulate (TSP) from air. For the Tradescantia micronucleus test, T. pallida cuttings were treated with the extract at 0.13, 0.25, ormore » 0.50 mg/ml. Subsequently, TSP was added at 0.3 mg/ml, and tetrads from the inflorescences were examined for micronuclei. For the micronucleus test in mouse bone marrow cells and the comet assay in mouse blood cells, Balb/c mice were treated for 15 days with the extract—3.9, 7.5, or 15.0 mg/kg body weight (BW)—or with casearin X—0.3, 0.25, or 1.2 mg/kg BW—after which they received TSP (3.75 mg/kg BW). In T. pallida and mouse bone marrow cells, the extract was antimutagenic at all concentrations tested. In mouse blood cells, the extract was antigenotoxic at all concentrations, whereas casearin X was not antimutagenic but was antigenotoxic at all concentrations. We conclude that C. sylvestris ethanolic extract and casearin X protect DNA from damage induced by airborne pollutants from sugarcane burning. -- Highlights: ► We assessed DNA protection of C. sylvestris ethanolic extract. ► We assessed DNA protection of casearin X. ► We used Tradescantia pallida micronucleus test as screening. ► We used comet assay and micronucleus test in mice. ► The compounds protected DNA against sugar cane burning pollutants.« less

[Nitrogen and phosphorus composition in urban runoff from the new development area in Beijing].

PubMed

Li, Li-Qing; Lü, Shu-Cong; Zhu, Ren-Xiao; Liu, Ze-Quan; Shan, Bao-Qing

2012-11-01

Stormwater runoff samples were collected from two impervious roof and road of the new development area in Beijing, during three rainfall events in an attempt to characterize the urban runoff and determine nitrogen and phosphorus composition. The outcomes are expected to offer the practical guidance in sources control of urban runoff pollution. The results indicated that the stormwater runoff from the studied area presented a strong first flush for all monitored events and constituents. Eighty percent of the total pollutant loads were transported by the first 10 mm flow volume for roof runoff, whereas 80% of the total pollutant loads were discharged by the first 15 mm flow volume for road runoff. Average EMCs of TSS, COD, TN, NH4(+) -N, NO3(-) -N and TP for roof runoff were 50.2 mg x L(-1), 81.7 mg x L(-1), 6.07 mg x L(-1), 2.94 mg x L(-1), 1.05 mg x L(-1), and 0.11 mg x L(-1), respectively. Average EMCs of TSS, COD, TN, NH4(+) -N, NO3(-)-N and TP for road runoff were 539.0 mg x L(-1), 276.4 mg x L(-1), 7.00 mg x L(-1), 1.71 mg x L(-1), 1.51 mg x L(-1), and 0.61 mg x L(-1), respectively. Moreover, for the roof runoff, the particle-bound fraction was 20.8% for COD, 12.3% for TN, and 49.7% for TP. For road runoff, the particle-bound fraction was 68.6% for COD, 20.0% for TN, and 73.6% for TP. Nitrogen in roof runoff was predominantly dissolved (87.7%), with ammonia (57.6%) and nitrate (22.5%). Nitrogen in road runoff was also predominantly dissolved (80.0%), with ammonia (42.1%) and nitrate (35.0%). These findings can assist the development of effective source control strategies to immobilize dissolved and particulate-bound nitrogen/phosphorus in urban stormwater.

Particle size distribution characteristics of cotton gin battery condenser system total particulate emissions

USDA-ARS?s Scientific Manuscript database

This report is part of a project to characterize cotton gin emissions from the standpoint of total particulate stack sampling and particle size analyses. In 2013, EPA published a more stringent standard for particulate matter with nominal diameter less than or equal to 2.5 µm (PM2.5). This created a...

The mouse lymphoma thymidine kinase assay for the assessment and comparison of the mutagenic activity of cigarette mainstream smoke particulate phase.

PubMed

Schramke, H; Meisgen, T J; Tewes, F J; Gomm, W; Roemer, E

2006-10-29

The mouse lymphoma thymidine kinase assay (MLA) has been optimized to quantitatively determine the in vitro mutagenicity of cigarette mainstream smoke particulate phase. To test whether the MLA is able to discriminate between different cigarette types, specially constructed cigarettes each containing a single tobacco type - Bright, Burley, or Oriental - were investigated. The mutagenic activity of the Burley cigarette was statistically significantly lower, up to approximately 40%, than that of the Bright and Oriental cigarettes. To determine the impact of two different sets of smoking conditions, American-blend cigarettes were smoked under US Federal Trade Commission/International Organisation for Standardisation conditions and under Massachusetts Department of Public Health (MDPH) conditions. Conventional cigarettes - eight from the US commercial market plus the Reference Cigarettes 1R4F and 2R4F - and an electrically heated cigarette smoking system (EHCSS) prototype were tested. There were no statistically significant differences between the two sets of smoking conditions on a per mg total particulate matter basis, although there was a consistent trend towards slightly lower mutagenic activity under MDPH conditions. The mutagenic activity of the EHCSS prototype was distinctly lower than that of the conventional cigarettes under both sets of smoking conditions. These results show that the MLA can be used to assess and compare the mutagenic activity of cigarette mainstream smoke particulate phase in the comprehensive toxicological assessment of cigarette smoke.

Mercury Distribution in the Deûle River (Northern France) Measured by the Diffusive Gradients in Thin Films Technique and Conventional Methods.

PubMed

Diviš, Pavel; Kadlecová, Milada; Ouddane, Baghdad

2016-05-01

The distribution of mercury in surface water and in sediment from Deûle River in Northern France was studied by application of conventional sampling methods and by diffusive gradients in thin films technique (DGT). Concentration of total dissolved mercury in surface water was 20.8 ± 0.8 ng l(-1). The particulate mercury concentration was 6.2 ± 0.6 µg g(-1). The particulate mercury was accumulated in sediment (9.9 ± 2.3 mg kg(-1)), and it was transformed by methylating bacteria to methylmercury, mainly in the first 2-cm layer of the sediment. Total dissolved concentration of mercury in sediment pore water obtained by application of centrifugation extraction was 17.6 ± 4.1 ng l(-1), and it was comparable with total dissolved pore water mercury concentration measured by DGT probe containing Duolite GT-73 resin gel (18.2 ± 4.3 ng l(-1)), taking the sediment heterogeneity and different principles of the applied methods into account. By application of two DGT probes with different resin gels specific for mercury, it was found that approximately 30% of total dissolved mercury in sediment pore water was present in labile forms easy available for biota. The resolution of mercury DGT depth profiles was 0.5 cm, which allows, unlike conventional techniques, to study the connection of the geochemical cycle of mercury with geochemical cycles of iron and manganese.

Atmospheric bulk deposition to the Lagoon of Venice Part II. Source apportionment analysis near the industrial zone of Porto Marghera, Italy.

PubMed

Guerzoni, S; Rampazzo, G; Molinaroli, E; Rossini, P

2005-09-01

Multivariate statistical analyses were applied to measurements of atmospheric deposition of total particulate (TSP), inorganic elements (Al, Ca, Na, K, Mg, Si, Mn, Fe, Zn, Ni, Cr, Cu, Pb, Cd, As, Hg, V and S) and organic compounds (PAH, PCB, HCB and PCDD/F) collected in four stations, all located in the Lagoon of Venice. Aerosols at the scale of the basin (i.e., within a distance of 20 km) were mainly characterised by two end-members, one natural (composed of mineral particulate and marine spray) and one anthropogenic (with at least two different source components), affecting the sites in various ways. Variability at the two distant (>20 km) sites (Valle Dogà, Valle Figheri) was mainly due to natural components, whereas the other two stations (city of Venice, Dogaletto, approximately 5 km) were mainly impacted by industrial (and urban) sources. Total annual inputs were compared with the limits recently set by law (maximum allowed discharge=MAD). In the year of study, MAD values were exceeded for total As, Cd, Hg, Pb, dissolved Zn, PAH and PCDD/F. These results indicate that industrial sources gave rise to a quasi-permanent compositional (background) effect near the industrial area. The risk associated with atmospheric deposition should be quantified within the DSPIR framework to avoid future negative consequences in populations living in the vicinity of Porto Marghera.

Source apportionment of particulate pollutants in the atmosphere over the Northern Yellow Sea

NASA Astrophysics Data System (ADS)

Wang, L.; Qi, J. H.; Shi, J. H.; Chen, X. J.; Gao, H. W.

2013-05-01

Atmospheric aerosol samples were collected over the Northern Yellow Sea of China during the years of 2006 and 2007, in which the Total Carbon (TC), Cu, Pb, Cd, V, Zn, Fe, Al, Na+, Ca2+, Mg2+, NH4+, NO3-, SO42-, Cl-, and K+ were measured. The principle components analysis (PCA) and positive matrix factorization (PMF) receptor models were used to identify the sources of particulate matter. The results indicated that seven factors contributed to the atmospheric particles over the Northern Yellow Sea, i.e., two secondary aerosols (sulfate and nitrate), soil dust, biomass burning, oil combustion, sea salt, and metal smelting. When the whole database was considered, secondary aerosol formation contributed the most to the atmospheric particle content, followed by soil dust. Secondary aerosols and soil dust consisted of 65.65% of the total mass of particulate matter. The results also suggested that the aerosols over the North Yellow Sea were heavily influenced by ship emission over the local sea area and by continental agricultural activities in the northern China, indicating by high loading of V in oil combustion and high loading of K+ in biomass burning. However, the contribution of each factor varied greatly over the different seasons. In spring and autumn, soil dust and biomass burning were the dominant factors. In summer, heavy oil combustion contributed the most among these factors. In winter, secondary aerosols were major sources. Backward trajectories analysis indicated the 66% of air mass in summer was from the ocean, while the air mass is mainly from the continent in other seasons.

Chemical characteristics of particulate, colloidal, and dissolved organic material in Loch Vale Watershed, Rocky Mountain National Park

USGS Publications Warehouse

McKnight, Diane M.; Harnish, R.; Wershaw, R. L.; Baron, Jill S.; Schiff, S.

1997-01-01

The chemical relationships among particulate and colloidal organic material and dissolved fulvic acid were examined in an alpine and subalpine lake and two streams in Loch Vale Watershed, Rocky Mountain National Park. The alpine lake, Sky Pond, had the lowest dissolved organic carbon (DOC) (0.37 mgC/L), the highest particulate carbon (POC) (0.13 mgC/L), and high algal biomass. The watershed of Sky Pond is primarily talus slope, and DOC and POC may be autochthonous. Both Andrews Creek and Icy Brook gain DOC as they flow through wet sedge meadows. The subalpine lake, The Loch, receives additional organic material from the surrounding forest and had a higher DOC (0.66 mgC/L). Elemental analysis, stable carbon isotopic compositon, and 13C-NMR characterization showed that: 1) particulate material had relatively high inorganic contents and was heterogeneous in compositon, 2) colloidal material was primarily carbohydrate material with a low inorganic content at all sites; and 3) dissolved fulvic acid varied in compositon among sites. The low concentration and carbohydrate-rich character of the colloidal material suggests that this fraction is labile to microbial degradation and may be turning over more rapidly than particulate fractions or dissolved fulvic acid. Fulvic acid from Andrews Creek had the lowest N content and aromaticity, whereas Sky Pond fulvic acid had a higher N content and lower aromaticity than fulvic acid from The Loch. The UV-visible spectra of the fulvic acids demonstrate that variation in characteristics with sources of organic carbon can explain to some extent the observed nonlinear relationship between UV-B extinction coefficients and DOC concentrations in lakes.

Exposure to coarse and fine particulate matter at and around major intra-urban traffic intersections of Ilorin metropolis, Nigeria

NASA Astrophysics Data System (ADS)

Adeniran, J. A.; Yusuf, R. O.; Olajire, A. A.

2017-10-01

This study aims to determine the seasonal variations and composition of suspended particulate matter in different sizes PM1.0, PM2.5, PM10 and the total suspended particles (TSP) emitted at major intra-urban traffic intersections (TIs) of Ilorin metropolis. The concentration levels of PM (PM1.0, PM2.5, PM10) obtained at the TIs during the rush hours (45.1, 77.9, and 513 μg/m3) are higher than the levels obtained for the non-rush hour periods (42.3, 62.7, and 390 μg/m3). The average on-road respiratory deposition dose (RDD) rates of PM1.0, PM2.5 and PM10 during the dry period at TIs types was found to be about 24%, 9% and 25% higher than those obtained during the wet period. Based on EF values calculated, Pb and Zn were anthropogenically-derived while Fe, Mn, Cr, Cu and Mg were of crustal source. Principal component analysis (PCA) has been applied to a set of PM data in order to determine the contribution of different sources. It was found that the main principal factors extracted from particulate emission data were related to exhaust and non-exhaust emissions such as tyre wears, oil and fuel combustion sources.

Dust in Rain During Drought: An Overlooked Pathway for Elemental Flux to Ecosystems

NASA Astrophysics Data System (ADS)

Ponette-González, A.; Collins, J. D., Jr.; Manuel, J. E.; Byers, T. A.; Glass, G. A.; Weathers, K. C.; Gill, T. E.

2017-12-01

Airborne dust has the potential to alter ecosystem productivity and biogeochemical cycles at local to global scales by enhancing atmospheric deposition of critical limiting nutrients and toxic pollutants. Suspended dust particles are delivered to ecosystems directly via dry deposition or in precipitation (wet deposition) by rainout and washout. Compared to dry deposition, dust removal by precipitation (dust-in-rain) is a seldom quantified yet potentially significant flux between the atmosphere and ecosystems. We quantified dust effects on the ionic and elemental composition of precipitation and on wet deposition rates at a National Atmospheric Deposition Program (NADP) monitoring site in west Texas during the extreme 2012 drought. Dust events were identified using meteorological data for stations within a 150-km radius buffer surrounding the NADP site. Data on the dissolved chemistry of weekly wet deposition samples and elemental analysis of the particulate fraction were analyzed. Calcium was the dominant dissolved ion in rainwater, comprising 61% of the total measured solute content during dust-in rain weeks. In the particulate fraction, Fe alone made up 81% of the elemental composition during dust-in-rain weeks. At this site, five dust-in-rain weeks delivered 19% of the annual water input (51 mm water). However, these weeks contributed 46-70% of the annual dissolved Ca2+, Mg2+, K+, Na+, PO43-, and Cl- flux and >55% of the particulate Fe, Ti, V, Ni, Rb, Ga, and Br flux. Sourcing analysis, conducted using an End-Member Mixing Algorithm (EMMA) on the particulate fraction identified Fe, Cu, Rb, and Sr end-members, representing 87% of the total elemental variance. In addition, EMMA showed that dust-in-rain weeks were more well mixed than other rainfall weeks. Preliminary findings for this west Texas site show that infrequent dust-in-rain events constitute an important but overlooked proportion of the elemental flux to ecosystems during severe drought.

High-Temperature Mechanical Properties of the P/M Extruded Mg -SiCp Composites

NASA Astrophysics Data System (ADS)

Labib, F.; Mahmudi, R.; Ghasemi, H. M.

2018-03-01

In the present study, pure magnesium reinforced with 0, 5, 10 and 15 vol.% SiC particulates was successfully prepared by powder metallurgy technique before being hot extruded. The average 14 μm grain size of the composite specimens remained almost unchanged after addition of SiC particles, while their dimensional stability was improved because of the reduction in the coefficient of thermal expansion (CTE) from 28.6 × 10-6 K-1 in pure Mg to 27.3, 25.3 and 23.4 × 10-6 K-1 in the Mg-5% SiC, Mg-10% SiC and Mg-15% SiC composites, respectively. Mechanical properties of the specimens were investigated in the temperature range of 298-498 K, implementing shear punch testing and hot hardness techniques. Depending on the test temperature, addition of SiC particles to the pure Mg matrix increased shear yield stress and ultimate shear strength of the materials by 5-25 and 6-23 MPa, respectively. The shear strength improvement was mainly attributed to the CTE mismatch strengthening mechanism (9.5-25.5 MPa), and to a lesser extent (1-4.5 MPa), to the load transfer mechanism. Finally, using the modified Clyne model, the contribution of different strengthening mechanisms to the total shear strength improvement in the composites was evaluated.

Exposure assessment of particulates of diesel and natural gas fuelled buses in silico.

PubMed

Pietikäinen, Mari; Oravisjärvi, Kati; Rautio, Arja; Voutilainen, Arto; Ruuskanen, Juhani; Keiski, Riitta L

2009-12-15

Lung deposition estimates of particulate emissions of diesel and natural gas (CNG) fuelled vehicles were studied by using in silico methodology. Particulate emissions and particulate number size distributions of two Euro 2 petroleum based diesel buses and one Euro 3 gas bus were measured. One of the petroleum based diesel buses used in the study was equipped with an oxidation catalyst on the vehicle (DI-OC) while the second had a partial-DPF catalyst (DI-pDPF). The third bus used was the gas bus with an oxidation catalyst on the vehicle (CNG-OC). The measurements were done using a transient chassis dynamometer test cycle (Braunschweig cycle) and an Electric Low Pressure Impactor (ELPI) with formed particulates in the size range of 7 nm to 10 microm. The total amounts of the emitted diesel particulates were 88-fold for DI-OC and 57-fold for DI-pDPF compared to the total amount of emitted CNG particulates. Estimates for the deposited particulates were computed with a lung deposition model ICRP 66 using in-house MATLAB scripts. The results were given as particulate numbers and percentages deposited in five different regions of the respiratory system. The percentages of particulates deposited in the respiratory system were 56% for DI-OC, 51% for DI-pDPF and 77% for CNG-OC of all the inhaled particulates. The result shows that under similar conditions the total lung dose of particulates originating from petroleum diesel fuelled engines DI-OC and DI-pDPF was more than 60-fold and 35-fold, respectively, compared to the lung dose of particulates originating from the CNG fuelled engine. The results also indicate that a majority (35-50%) of the inhaled particulates emitted from the tested petroleum diesel and CNG engines penetrate deep into the unciliated regions of the lung where gas-exchange occurs.

Development of a job-exposure matrix for exposure to total and fine particulate matter in the aluminum industry.

PubMed

Noth, Elizabeth M; Dixon-Ernst, Christine; Liu, Sa; Cantley, Linda; Tessier-Sherman, Baylah; Eisen, Ellen A; Cullen, Mark R; Hammond, S Katharine

2014-01-01

Increasing evidence indicates that exposure to particulate matter (PM) at environmental concentrations increases the risk of cardiovascular disease, particularly PM with an aerodynamic diameter of less than 2.5 μm (PM(2.5)). Despite this, the health impacts of higher occupational exposures to PM(2.5) have rarely been evaluated. In part, this research gap derives from the absence of information on PM(2.5) exposures in the workplace. To address this gap, we have developed a job-exposure matrix (JEM) to estimate exposure to two size fractions of PM in the aluminum industry. Measurements of total PM (TPM) and PM(2.5) were used to develop exposure metrics for an epidemiologic study. TPM exposures for distinct exposure groups (DEGs) in the JEM were calculated using 8385 personal TPM samples collected at 11 facilities (1980-2011). For eight of these facilities, simultaneous PM(2.5) and TPM personal monitoring was conducted from 2010 to 2011 to determine the percent of TPM that is composed of PM(2.5) (%PM(2.5)) in each DEG. The mean TPM from the JEM was then multiplied by %PM(2.5) to calculate PM(2.5) exposure concentrations in each DEG. Exposures in the smelters were substantially higher than in fabrication units; mean TPM concentrations in smelters and fabrication facilities were 3.86 and 0.76 mg/m(3), and the corresponding mean PM(2.5) concentrations were 2.03 and 0.40 mg/m(3). Observed occupational exposures in this study generally exceeded environmental PM(2.5) concentrations by an order of magnitude.

An analysis of field-aged diesel particulate filter performance: particle emissions before, during, and after regeneration.

PubMed

Barone, Teresa L; Storey, John M E; Domingo, Norberto

2010-08-01

A field-aged, passive diesel particulate filter (DPF) used in a school bus retrofit program was evaluated for emissions of particle mass and number concentration before, during, and after regeneration. For the particle mass measurements, filter samples were collected for gravimetric analysis with a partial flow sampling system, which sampled proportionally to the exhaust flow. A condensation particle counter and scanning mobility particle sizer measured total number concentration and number-size distributions, respectively. The results of the evaluation show that the number concentration emissions decreased as the DPF became loaded with soot. However, after soot removal by regeneration, the number concentration emissions were approximately 20 times greater, which suggests the importance of the soot layer in helping to trap particles. Contrary to the number concentration results, particle mass emissions decreased from 6 +/- 1 mg/hp-hr before regeneration to 3 +/- 2 mg/hp-hr after regeneration. This indicates that nanoparticles with diameters less than 50 nm may have been emitted after regeneration because these particles contribute little to the total mass. Overall, average particle emission reductions of 95% by mass and 10,000-fold by number concentration after 4 yr of use provided evidence of the durability of a field-aged DPF. In contrast to previous reports for new DPFs in which elevated number concentrations occurred during the first 200 sec of a transient cycle, the number concentration emissions were elevated during the second half of the heavy-duty Federal Test Procedure (FTP) when high speed was sustained. This information is relevant for the analysis of mechanisms by which particles are emitted from field-aged DPFs.

Characterization of metal and trace element contents of particulate matter (PM10) emitted by vehicles running on Brazilian fuels-hydrated ethanol and gasoline with 22% of anhydrous ethanol.

PubMed

Ferreira da Silva, Moacir; Vicente de Assunção, João; de Fátima Andrade, Maria; Pesquero, Célia R

2010-01-01

Emission of fine particles by mobile sources has been a matter of great concern due to its potential risk both to human health and the environment. Although there is no evidence that one sole component may be responsible for the adverse health outcomes, it is postulated that the metal particle content is one of the most important factors, mainly in relation to oxidative stress. Data concerning the amount and type of metal particles emitted by automotive vehicles using Brazilian fuels are limited. The aim of this study was to identify inhalable particles (PM(10)) and their trace metal content in two light-duty vehicles where one was fueled with ethanol while the other was fueled with gasoline mixed with 22% of anhydrous ethanol (gasohol); these engines were tested on a chassis dynamometer. The elementary composition of the samples was evaluated by the particle-induced x-ray emission technique. The experiment showed that total emission factors ranged from 2.5 to 11.8 mg/km in the gasohol vehicle, and from 1.2 to 3 mg/km in the ethanol vehicle. The majority of particles emitted were in the fine fraction (PM(2.5)), in which Al, Si, Ca, and Fe corresponded to 80% of the total weight. PM(10) emissions from the ethanol vehicle were about threefold lower than those of gasohol. The elevated amount of fine particulate matter is an aggravating factor, considering that these particles, and consequently associated metals, readily penetrate deeply into the respiratory tract, producing damage to lungs and other tissues.

Sulfur speciation and bioaccumulation in camphor tree leaves as atmospheric sulfur indicator analyzed by synchrotron radiation XRF and XANES.

PubMed

Zeng, Jianrong; Zhang, Guilin; Bao, Liangman; Long, Shilei; Tan, Mingguang; Li, Yan; Ma, Chenyan; Zhao, Yidong

2013-03-01

Analyzing and understanding the effects of ambient pollution on plants is getting more and more attention as a topic of environmental biology. A method based on synchrotron radiation X-ray fluorescence and X-ray absorption near edge structure spectroscopy was established to analyze the sulfur concentration and speciation in mature camphor tree leaves (CTLs), which were sampled from 5 local fields in Shanghai, China. Annual SO2 concentration, SO4(2-) concentration in atmospheric particulate, SO4(2-) and sulfur concentration in soil were also analyzed to explore the relationship between ambient sulfur sources and the sulfur nutrient cycling in CTLs. Total sulfur concentration in mature camphor tree leaves was 766-1704 mg/kg. The mainly detected sulfur states and their corresponding compounds were +6 (sulfate, include inorganic sulfate and organic sulfate), +5.2 (sulfonate), +2.2 (suloxides), +0.6 (thiols and thiothers), +0.2 (organic sulfides). Total sulfur concentration was strongly correlated with sulfate proportion with a linear correlation coefficient up to 0.977, which suggested that sulfur accumulated in CTLs as sulfate form. Reduced sulfur compounds (organic sulfides, thiols, thioethers, sulfoxide and sulfonate) assimilation was sufficed to meet the nutrient requirement for growth at a balanced level around 526 mg/kg. The sulfate accumulation mainly caused by atmospheric sulfur pollution such as SO2 and airborne sulfate particulate instead of soil contamination. From urban to suburb place, sulfate in mature CTLs decreased as the atmospheric sulfur pollution reduced, but a dramatic increase presented near the seashore, where the marine sulfate emission and maritime activity pollution were significant. The sulfur concentration and speciation in mature CTLs effectively represented the long-term biological accumulation of atmospheric sulfur pollution in local environment.

Sorption and Release of Organics by Primary, Anaerobic, and Aerobic Activated Sludge Mixed with Raw Municipal Wastewater

PubMed Central

Modin, Oskar; Saheb Alam, Soroush; Persson, Frank; Wilén, Britt-Marie

2015-01-01

New activated sludge processes that utilize sorption as a major mechanism for organics removal are being developed to maximize energy recovery from wastewater organics, or as enhanced primary treatment technologies. To model and optimize sorption-based activated sludge processes, further knowledge about sorption of organics onto sludge is needed. This study compared primary-, anaerobic-, and aerobic activated sludge as sorbents, determined sorption capacity and kinetics, and investigated some characteristics of the organics being sorbed. Batch sorption assays were carried out without aeration at a mixing velocity of 200 rpm. Only aerobic activated sludge showed net sorption of organics. Sorption of dissolved organics occurred by a near-instantaneous sorption event followed by a slower process that obeyed 1st order kinetics. Sorption of particulates also followed 1st order kinetics but there was no instantaneous sorption event; instead there was a release of particles upon mixing. The 5-min sorption capacity of activated sludge was 6.5±10.8 mg total organic carbon (TOC) per g volatile suspend solids (VSS) for particulate organics and 5.0±4.7 mgTOC/gVSS for dissolved organics. The observed instantaneous sorption appeared to be mainly due to organics larger than 20 kDa in size being sorbed, although molecules with a size of about 200 Da with strong UV absorbance at 215–230 nm were also rapidly removed. PMID:25768429

Relationship between nutrients and plankton biomass in the turbidity maximum zone of the Pearl River Estuary.

PubMed

Shi, Zhen; Xu, Jie; Huang, Xiaoping; Zhang, Xia; Jiang, Zhijian; Ye, Feng; Liang, Ximei

2017-07-01

Nutrients, dissolved and particulate organic carbon and plankton (bacterio-, phyto- and zoo-) were compared in the turbidity maximum zone (TMZ) and adjacent areas (non-TMZ) in the Pearl River estuary. Our results showed that high levels of suspended substances had marked effect on dynamics of nutrients and plankton in the TMZ. Based on the cluster analysis of total suspended solids (TSS) concentrations, all stations were divided into two groups, TMZ with average TSS of 171mg/L and non-TMZ of 45mg/L. Suspended substances adsorbed PO 4 3- and dissolved organic carbon, resulting in higher particulate phosphorus and organic carbon (POC) and lower PO 4 3- and DOC in the TMZ, compared to the non-TMZ. However, suspended substances had limited effect on nitrogenous nutrients. Phytoplankton growth was light-limited due to high concentrations of suspended substances in the TMZ and a peak of phytoplankton abundance appeared in the non-TMZ. In contrast, the highest bacterial abundance occurred in the TMZ, which was likely partly responsible for low DOC levels. Two peaks of zooplankton abundance observed in the TMZ and non-TMZ in the Pearl River estuary were primarily supported by bacteria and phytoplankton, respectively. Our finding implied that high levels of suspended solids in the TMZ affect the trophic balance. Copyright © 2016. Published by Elsevier B.V.

Airborne particulate matter in spacecraft

NASA Technical Reports Server (NTRS)

1988-01-01

Acceptability limits and sampling and monitoring strategies for airborne particles in spacecraft were considered. Based on instances of eye and respiratory tract irritation reported by Shuttle flight crews, the following acceptability limits for airborne particles were recommended: for flights of 1 week or less duration (1 mg/cu m for particles less than 10 microns in aerodynamic diameter (AD) plus 1 mg/cu m for particles 10 to 100 microns in AD); and for flights greater than 1 week and up to 6 months in duration (0.2 mg/cu m for particles less than 10 microns in AD plus 0.2 mg/cu m for particles 10 to 100 microns in AD. These numerical limits were recommended to aid in spacecraft atmosphere design which should aim at particulate levels that are a low as reasonably achievable. Sampling of spacecraft atmospheres for particles should include size-fractionated samples of 0 to 10, 10 to 100, and greater than 100 micron particles for mass concentration measurement and elementary chemical analysis by nondestructive analysis techniques. Morphological and chemical analyses of single particles should also be made to aid in identifying airborne particulate sources. Air cleaning systems based on inertial collection principles and fine particle collection devices based on electrostatic precipitation and filtration should be considered for incorporation into spacecraft air circulation systems. It was also recommended that research be carried out in space in the areas of health effects and particle characterization.

Processing of combined domestic bath and laundry waste waters for reuse as commode flushing water

NASA Technical Reports Server (NTRS)

Hypes, W. D.; Batten, C. E.; Wilkins, J. R.

1975-01-01

An experimental investigation of processes and system configurations for reclaiming combined bath and laundry waste waters for reuse as commode flush water was conducted. A 90-min recycle flow was effective in removing particulates and in improving other physical characteristics to the extent that the filtered water was subjectively acceptable for reuse. The addition of a charcoal filter resulted in noticeable improvements in color, turbidity, and suds elimination. Heating and chlorination of the waste waters were investigated for reducing total organism counts and eliminating coliform organisms. A temperature of 335.9 K (145 F) for 30 min and chlorine concentrations of 20 mg/l in the collection tank followed by 10 mg/l in the storage tank were determined to be adequate for this purpose. Water volume relationships and energy-use rates for the waste water reuse systems are also discussed.

Gaseous and particulate emissions from prescribed burning in Georgia.

PubMed

Lee, Sangil; Baumann, Karsten; Schauer, James J; Sheesley, Rebecca J; Naeher, Luke P; Meinardi, Simone; Blake, Donald R; Edgerton, Eric S; Russell, Armistead G; Clements, Mark

2005-12-01

Prescribed burning is a significant source of fine particulate matter (PM2.5) in the southeastern United States. However, limited data exist on the emission characteristics from this source. Various organic and inorganic compounds both in the gas and particle phase were measured in the emissions of prescribed burnings conducted at two pine-dominated forest areas in Georgia. The measurements of volatile organic compounds (VOCs) and PM2.5 allowed the determination of emission factors for the flaming and smoldering stages of prescribed burnings. The VOC emission factors from smoldering were distinctly higher than those from flaming except for ethene, ethyne, and organic nitrate compounds. VOC emission factors show that emissions of certain aromatic compounds and terpenes such as alpha and beta-pinenes, which are important precursors for secondary organic aerosol (SOA), are much higher from active prescribed burnings than from fireplace wood and laboratory open burning studies. Levoglucosan is the major particulate organic compound (POC) emitted for all these studies, though its emission relative to total organic carbon (mg/g OC) differs significantly. Furthermore, cholesterol, an important fingerprint for meat cooking, was observed only in our in situ study indicating a significant release from the soil and soil organisms during open burning. Source apportionment of ambient primary fine particulate OC measured at two urban receptor locations 20-25 km downwind yields 74 +/- 11% during and immediately after the burns using our new in situ profile. In comparison with the previous source profile from laboratory simulations, however, this OC contribution is on average 27 +/- 5% lower.

Seasonal variations and size distributions of water-soluble ions of atmospheric particulate matter at Shigatse, Tibetan Plateau.

PubMed

Yang, Yongjie; Zhou, Rui; Yan, Yan; Yu, Yue; Liu, Junqing; Di, Yi'an; Du, Zhenyu; Wu, Dan

2016-02-01

Size-segregated atmospheric particulate matter (PM) samples were collected from July 2012 to September 2013 at Shigatse, high-altitude (3836 m above sea level) site on the south Tibetan Plateau (TP); objectives were to determine the characteristics and size distribution of water-soluble ions (WSIs). Eight major WSIs (Na(+), K(+), Mg(2+), Ca(2+), NH4(+), Cl(-), SO4(2-), and NO3(-)) were detected by ion chromatography. The total concentrations of WSIs were 6370 ± 1916 ng m(-3) in dry season (October - December, January - April), and 5261 ± 769 ng/m(3) during wet phase (May - September). The contribution of K(+) (130 ng m(-3)), Cl(-) (2035 ng m(-3)), SO4(2-) (1176 ng m(-3)), and NO3(-) (706 ng m(-3))(-)were significantly enhanced in dry season, and that of Na(+) (455 ng m(-3)), Mg(2+)(65.4 ng m(-3)), Ca(2+)(1034 ng m(-3)), and NH4(+) (1948 ng m(-3)) were significantly enhanced during wet phase. Mg(2+) and Ca(2+) were concentrated in the coarse mode, and the other ions concentrated in fine mode and coarse mode during two seasons. The correlation coefficients between K(+) and NH4(+), Cl(-), SO4(2-) and NO3(-) were 0.58 (P < 0.01), 0.40 (P < 0.05), 0.82 (P < 0.01) and 0.69 (P < 0.01), indicating their dominant contribution from biomass burning in dry season. The significant correlation between NH4(+) and HCO3(-) which were calculated by ion balance (r = 0.89, P < 0.01), suggesting the source from nitrogen fertilizers during wet phase. Copyright © 2015 Elsevier Ltd. All rights reserved.

An alternative approach to recovering valuable metals from zinc phosphating sludge.

PubMed

Kuo, Yi-Ming

2012-01-30

This study used a vitrification process (with good potential for commercialization) to recover valuable metals from Zn phosphating sludge. The involved vitrification process achieves two major goals: it transformed hazardous Zn phosphating sludge into inert slag and it concentrated Fe (83.5%) and Zn (92.8%) into ingot and fine particulate-phase material, respectively. The Fe content in the ingot was 278,000 mg/kg, making the ingot a potential raw material for iron making. The fine particulate-phase material (collected from flue gas) contained abundant Zn (544,000 mg/kg) in the form of ZnO. The content (67.7%) of ZnO was high, so it can be directly sold to refineries. The recovered coarse particulate-phase material, with insufficient amount of ZnO, can be recycled as a feeding material for Zn re-concentration. Therefore, the vitrification process can not only treat hazardous materials but also effectively recover valuable metals. Copyright © 2011 Elsevier B.V. All rights reserved.

In situ microcosms to study the impact of heavy metals resuspended by dredging on periphyton in a tropical estuary.

PubMed

Nayar, S; Goh, B P L; Chou, L M; Reddy, S

2003-08-20

Ponggol estuary, located on the northeastern coast of Singapore, is heavily impacted by reclamation, dredging, construction and shipping. Tin, lead, nickel, cadmium, copper and zinc in the particulate and dissolved fraction and in sediments were monitored biweekly in the estuary from July 1999 to June 2000. The concentrations of tin, lead, nickel, cadmium, copper and zinc were observed to range from ND-92 ppm, ND-303 ppm, ND-2818 ppm, ND-74 ppm, ND-1117 ppm and ND-137000 ppm, respectively, in the dissolved, particulate and sediments fractions. Intensive dredging activity occurred during the monitoring period, and this may have led to the resuspension and increased bioavailability of particulate metals. Periphytic algae were established on glass slides and exposed to previously measured environmental levels of heavy metals using in situ estuarine microcosms. The toxicity of heavy metals in various fractions to periphytic algae was assessed from the changes in their chlorophyll a content. Cadmium had the least significant effect followed by lead, zinc, nickel, tin and copper at all concentrations tested. A reduction in periphyton biomass (with respect to controls) of 95-100% was observed for treatments with metals in particulate form. In addition, exposure to contaminated sediments for 3 days significantly decreased chlorophyll a by 90-99% compared to controls. High concentrations of zinc (9893-17240 mg l(-1)), copper (5-11 mg l(-1)) and cadmium (1-1.8 mg l(-1)) recorded in the aqueous phase of treatment microcosms, and attributed to release from the contaminated sediments, could account for the toxicity to periphyton.

Acute decrease in HDL cholesterol associated with exposure to welding fumes.

PubMed

Rice, Mary Berlik; Cavallari, Jenn; Fang, Shona; Christiani, David

2011-01-01

To investigate acute changes in circulating lipids after exposure to relatively high levels of particulate matter through welding. Using a repeated measures panel study, lipid levels before and after welding and personal exposures to fine particulate matter (PM2.5) were measured in 36 male welders over 63 exposure and/or control days. There was a trend toward decrease in HDL (-2.3 mg/dL, P = 0.08) 18 hours after welding. This effect became significant (-2.6 mg/dL, P = 0.05) after adjustment for possible confounders. The effect was strongest (-4.3 mg/dL, P = 0.02) among welders who did not weld the day before the study. There were no significant changes in other lipids associated with welding or PM2.5 exposure. Welding exposure was associated with an acute decrease in circulating HDL, which may relate to the inflammatory and proatherosclerotic effects of fine particle exposure.

Characterization of the products attained from a thermal treatment of a mix of zinc-carbon and alkaline batteries.

PubMed

Kuo, Yi-Ming; Lin, Chitsan; Wang, Jian-Wen; Huang, Kuo-Lin; Tsai, Cheng-Hsien; Wang, Chih-Ta

2016-01-01

This study applies a thermal separation process (TSP) to recover Fe, Mn, and Zn from hazardous spent zinc-carbon and alkaline batteries. In the TSP, the batteries were heated together with a reducing additive and the metals in batteries, according to their boiling points and densities, were found to move into three major output materials: slag, ingot (mainly Fe and Mn), and particulate (particularly Zn). The slag well encapsulated the heavy metals of interest and can be recycled for road pavement or building materials. The ingot had high levels of Fe (522,000 mg/kg) and Mn (253,000 mg/kg) and can serve as an additive for stainless steel-making processes. The particulate phase had a Zn level of 694,000 mg/kg which is high enough to be directly sold for refinement. Overall, the TSP effectively recovered valuable metals from the hazardous batteries.

Performance testing of NIOSH Method 5524/ASTM Method D-7049-04, for determination of metalworking fluids.

PubMed

Glaser, Robert; Kurimo, Robert; Shulman, Stanley

2007-08-01

A performance test of NIOSH Method 5524/ASTM Method D-7049-04 for analysis of metalworking fluids (MWF) was conducted. These methods involve determination of the total and extractable weights of MWF samples; extractions are performed using a ternary blend of toluene:dichloromethane:methanol and a binary blend of methanol:water. Six laboratories participated in this study. A preliminary analysis of 20 blank samples was made to familiarize the laboratories with the procedure(s) and to estimate the methods' limits of detection/quantitation (LODs/LOQs). Synthetically generated samples of a semisynthetic MWF aerosol were then collected on tared polytetrafluoroethylene (PTFE) filters and analyzed according to the methods by all participants. Sample masses deposited (approximately 400-500 micro g) corresponded to amounts expected in an 8-hr shift at the NIOSH recommended exposure levels (REL) of 0.4 mg/m(3) (thoracic) and 0.5 mg/m(3) (total particulate). The generator output was monitored with a calibrated laser particle counter. One laboratory significantly underreported the sampled masses relative to the other five labs. A follow-up study compared only gravimetric results of this laboratory with those of two other labs. In the preliminary analysis of blanks; the average LOQs were 0.094 mg for the total weight analysis and 0.136 mg for the extracted weight analyses. For the six-lab study, the average LOQs were 0.064 mg for the total weight analyses and 0.067 mg for the extracted weight analyses. Using ASTM conventions, h and k statistics were computed to determine the degree of consistency of each laboratory with the others. One laboratory experienced problems with precision but not bias. The precision estimates for the remaining five labs were not different statistically (alpha = 0.005) for either the total or extractable weights. For all six labs, the average fraction extracted was > or =0.94 (CV = 0.025). Pooled estimates of the total coefficients of variation of analysis were 0.13 for the total weight samples and 0.13 for the extracted weight samples. An overall method bias of -5% was determined by comparing the overall mean concentration reported by the participants to that determined by the particle counter. In the three-lab follow-up study, the nonconsistent lab reported results that were unbiased but statistically less precise than the others; the average LOQ was 0.133 mg for the total weight analyses. It is concluded that aerosolized MWF sampled at concentrations corresponding to either of the NIOSH RELs can generally be shipped unrefrigerated, stored refrigerated up to 7 days, and then analyzed quantitatively and precisely for MWF using the NIOSH/ASTM procedures.

Carbon Balance in an Irrigated Corn Field after Inorganic Fertilizer or Manure Application

NASA Astrophysics Data System (ADS)

Lentz, R. D.; Lehrsch, G. A.

2014-12-01

Little is known about inorganic fertilizer or manure effects on organic carbon (OC) and inorganic C (IC) losses from a furrow irrigated field, particularly in the context of other system C gains or losses. In 2003 and 2004, we measured dissolved organic and inorganic C (DOC, DIC), particulate OC and IC (POC, PIC) concentrations in irrigation inflow, runoff, and percolation waters (6-7 irrigations/y); C inputs from soil amendments and crop biomass; harvested C; and gaseous C emissions from field plots cropped to silage corn (Zea mays L.) in southern Idaho. Annual treatments included: (M) 13 (y 1) and 34 Mg/ha (y 2) stockpiled dairy manure; (F) 78 (yr 1) and 195 kg N/ha (y 2) inorganic N fertilizer; or (NA) no amendment--control. The mean annual total C input into M plots averaged 16.1 Mg/ha, 1.4-times greater than that for NA (11.5 Mg/ha) or F (11.1 Mg/ha), while total C outputs for the three treatments were similar, averaging 11.8 Mg/ha. Thus, the manure plots ended each growing season with an average net gain of 3.8 Mg C/ha (a positive net C flux), while the control (-0.5 Mg C/ha) and fertilizer (-0.4 Mg C/ha) treatments finished the season with a net C loss. Atmospheric CO2 incorporated into the crop biomass contributed 96% of the mean annual C input to NA and F plots but only 68% to M plots. We conclude that nutrient amendments substantially influence the short-term carbon balance of our furrow-irrigated system. Amendments had both direct and indirect influences on individual C components, such as the losses of DIC and POC in runoff and DOC in percolation water, producing temporally complex outcomes which may depend on environmental conditions external to the field.

Particulate carbon and nitrogen and suspended particulate matter in the Sacramento River at Rio Vista, California, January 3 - May 26, 1983 and October 31, 1983 - November 29, 1984

USGS Publications Warehouse

Hager, Stephen W.

1994-01-01

Particulate matter was collected at Rio Vista, California, in two study periods; the first, from January 3 to May 26, 1983; the second from October 31, 1983 to November 29, 1984. Concentrations of suspended particulate matter were measured gravimetrically on silver membrane filters. The pooled standard deviation on replicated samples was 1.4 mg/L, giving a coefficient of variation of 5.7 percent. Concentrations of particulate carbon and nitrogen were measured during a Perkin-Elmer model 240C elemental analyzer to combust material collected on glass fiber filters. Refrigeration of samples prior to filtration was shown to be a likely influence on precision of duplicate analyses. Median deviations between duplicates for carbon were 5.4 percent during the first study period and 8.9 percent during the second. For nitrogen, median deviations were 4.9 percent and 7.2 percent, respectively. This report presents the data for concentrations of suspended particulate material, the duplicate analyses for particulate carbon and nitrogen, and the volumes of sample filtered for the particulate carbon and nitrogen analyses for both studies. Not all samples collected during the second study have been analyzed for particulate carbon and nitrogen.

Occupational PAH exposures during prescribed pile burns.

PubMed

Robinson, M S; Anthony, T R; Littau, S R; Herckes, P; Nelson, X; Poplin, G S; Burgess, J L

2008-08-01

Wildland firefighters are exposed to particulate matter and gases containing polycyclic aromatic hydrocarbons (PAHs), many of which are known carcinogens. Our objective was to evaluate the extent of firefighter exposure to particulate and PAHs during prescribed pile burns of mainly ponderosa pine slash and determine whether these exposures were correlated with changes in urinary 1-hydroxypyrene (1-HP), a PAH metabolite. Personal and area sampling for particulate and PAH exposures were conducted on the White Mountain Apache Tribe reservation, working with 21 Bureau of Indian Affairs/Fort Apache Agency wildland firefighters during the fall of 2006. Urine samples were collected pre- and post-exposure and pulmonary function was measured. Personal PAH exposures were detectable for only 3 of 16 PAHs analyzed: naphthalene, phenanthrene, and fluorene, all of which were identified only in vapor-phase samples. Condensed-phase PAHs were detected in PM2.5 area samples (20 of 21 PAHs analyzed were detected, all but naphthalene) at concentrations below 1 microg m(-3). The total PAH/PM2.5 mass fractions were roughly a factor of two higher during smoldering (1.06 +/- 0.15) than ignition (0.55 +/- 0.04 microg mg(-1)). There were no significant changes in urinary 1-HP or pulmonary function following exposure to pile burning. In summary, PAH exposures were low in pile burns, and urinary testing for a PAH metabolite failed to show a significant difference between baseline and post-exposure measurements.

The Physical Clogging of the Landfill Leachate Collection System in China: Based on Filtration Test and Numerical Modelling.

PubMed

Liu, Yili; Sun, Weixin; Du, Bing; Liu, Jianguo

2018-02-12

Clogging of the leachate collection system (LCS) has been a common operation problem in municipal solid waste (MSW) landfills in China, which can result in high water levels that threaten the safety of landfill operations. To determine the cause of failure in an LCS, raw leachate from a municipal solid waste transfer station was collected and the high content of particulate matter was characterized. Based on the parameters obtained in a filtration test, a numerical simulation was performed to estimate the influence of particle deposition on drainage system clogging. The results showed that LCSs were confronted with the risk of clogging due to the deposition of particulate matter resulting from the higher concentration of total suspended solids (TSS level > 2200 mg L -1 ) and larger particle size (>30% TSS particles > 15 μm) in the leachate. On one hand, the non-woven geotextile, as the upper layer of the LCS, retained most particulate matter of large diameters, reducing its hydraulic conductivity to approximately 10 -8 to 10 -9 m s -1 after 1-2 years of operation and perching significant leachate above it (0.6-0.7 m). On the other hand, the geotextile prevented the gravel layer from physically clogging and minimized the leachate head above the bottom liner. Therefore, the role of geotextile should be balanced to optimize the LCS in MSW landfills in China.

INTERNATIONAL APPROACHES TO DEVELOPING STANDARDS FOR NONCRITERIA POLLUTANTS

EPA Science Inventory

Much of the initial interest in the control of pollutants, both in the United States and abroad, focused on such "traditional" pollutants as sulfur dioxide, particulate matter, Total Suspended Particulate (TSP) and particulate matter, nitrogen oxides, carbon monoxide, ozone, and ...

Association of expired nitric oxide with occupational particulate exposure.

PubMed Central

Kim, Jee Young; Wand, Matthew P; Hauser, Russ; Mukherjee, Sutapa; Herrick, Robert F; Christiani, David C

2003-01-01

Particulate air pollution has been associated with adverse respiratory health effects. This study assessed the utility of expired nitric oxide to detect acute airway responses to metal-containing fine particulates. Using a repeated-measures study design, we investigated the association between the fractional concentration of expired nitric oxide (F(E)NO) and exposure to particulate matter with an aerodynamic mass median diameter of less than or equal to 2.5 micro m (PM(2.5)) in boilermakers exposed to residual oil fly ash and metal fumes. Subjects were monitored for 5 days during boiler repair overhauls in 1999 (n = 20) or 2000 (n = 14). The Wilcoxon median baseline F(E)NO was 10.6 ppb [95% confidence interval (CI): 9.1, 12.7] in 1999 and 7.4 ppb (95% CI: 6.7, 8.0) in 2000. The Wilcoxon median PM(2.5) 8-hr time-weighted average was 0.56 mg/m(3) (95% CI: 0.37, 0.93) in 1999 and 0.86 mg/m(3) (95% CI: 0.65, 1.07) in 2000. F(E)NO levels during the work week were significantly lower than baseline F(E)NO in 1999 (p < 0.001). A significant inverse exposure-response relationship between log-transformed F(E)NO and the previous workday's PM(2.5) concentration was found in 1999, after adjusting for smoking status, age, and sampling year. With each 1 mg/m(3) incremental increase in PM(2.5) exposure, log F(E)NO decreased by 0.24 (95% CI: -0.38, -0.10) in 1999. The lack of an exposure-response relationship between PM(2.5) exposure and F(E)NO in 2000 could be attributable to exposure misclassification resulting from the use of respirators. In conclusion, occupational exposure to metal-containing fine particulates was associated with significant decreases in F(E)NO in a survey of workers with limited respirator usage. PMID:12727593

Formation of Particulate Matter from the Oxidation of Evaporated Hydraulic Fracturing Wastewater.

PubMed

Bean, Jeffrey K; Bhandari, Sahil; Bilotto, Anthony; Hildebrandt Ruiz, L

2018-04-17

The use of hydraulic fracturing for production of petroleum and natural gas has increased dramatically in the past decade, but the environmental impacts of this technology remain unclear. Experiments were conducted to quantify airborne emissions from 12 samples of hydraulic fracturing flowback wastewater collected in the Permian Basin, as well as the photochemical processing of these emissions leading to the formation of particulate matter (PM). The concentration of total volatile carbon (hydrocarbons evaporating at room temperature) averaged 29 mg of carbon per liter. After photochemical oxidation under high NO x conditions, the amount of organic PM formed per milliliter of wastewater evaporated averaged 24 μg; the amount of ammonium nitrate formed averaged 262 μg. Based on the mean PM formation observed in these experiments, the estimated formation of PM from evaporated flowback wastewater in the state of Texas is in the range of estimated PM emissions from diesel engines used in oil rigs. Evaporation of flowback wastewater, a hitherto unrecognized source of secondary pollutants, could significantly contribute to ambient PM concentrations.

AN EVALUATION OF THE PROTEIN MASS OF PARTICULATE MATTER

EPA Science Inventory

A comparison of ambient particulate matter mass concentrations with the total protein mass concentration has not been performed previously for North Carolina and was the goal of this study. The analysis of total protein mass was used as an all inclusive indicator of biologically ...

40 CFR 52.330 - Control strategy: Total suspended particulates.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Total suspended particulates. 52.330 Section 52.330 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Colorado § 52.330 Control strategy...

Tidal cycles of total particulate mercury in the Jade Bay, lower Saxonian Wadden Sea, southern North Sea.

PubMed

Jin, Huafang; Liebezeit, Gerd

2013-01-01

In this study, we evaluate the nature of the relationship between particulate matter and total mercury concentrations. For this purpose, we estimate both of the two values in water column over 12-h tidal cycles of the Jade Bay, southern North Sea. Total particulate mercury in 250 mL water samples was determined by oxygen combustion-gold amalgamation. Mercury contents varied from 63 to 259 ng/g suspended particulate matter (SPM) or 3.5-52.8 ng/L in surface waters. Total particulate mercury content (THg(p)) was positively correlated with (SPM), indicating that mercury in tidal waters is mostly associated with (SPM), and that tidal variations of total particulate mercury are mainly due to changes in (SPM) content throughout the tidal cycle. Maximum values for THg(p) were observed during mid-flood and mid-ebb, while the lowest values were determined at low tide and high tide. These data suggest that there are no mercury point sources in the Jade Bay. Moreover, the THg(p) content at low tide and high tide were significantly lower than the values recorded in the bottom sediment of the sampling site (>200 ng/g DW), while THg(p) content during the mid-flood and mid-ebb were comparable to the THg content in the surface bottom sediments. Therefore, changes in THg(p) content in the water column due to tidal forcing may have resulted from re-suspension of underlying surface sediments with relatively high mercury content.

COPPER-DEPENDENT INFLAMMATION AND NUCLEAR FACTOR-KB ACTIVATION BY PARTICULATE AIR POLLUTION

EPA Science Inventory

Particulate air pollution causes increased cardiopulmonary morbidity and mortality, but the chemical determinants responsible for its biologic effects are not understood. We studied the effect of total suspended particulates collected in Provo, Utah, an area where an increase in ...

Contrasting seasonality in optical-biogeochemical properties of the Baltic Sea

PubMed Central

Ylöstalo, Pasi; Kallio, Kari Y.; Spilling, Kristian; Kutser, Tiit

2017-01-01

Optical-biogeochemical relationships of particulate and dissolved organic matter are presented in support of remote sensing of the Baltic Sea pelagic. This system exhibits strong seasonality in phytoplankton community composition and wide gradients of chromophoric dissolved organic matter (CDOM), properties which are poorly handled by existing remote sensing algorithms. Absorption and scattering properties of particulate matter reflected the seasonality in biological (phytoplankton succession) and physical (thermal stratification) processes. Inherent optical properties showed much wider variability when normalized to the chlorophyll-a concentration compared to normalization to either total suspended matter dry weight or particulate organic carbon. The particle population had the largest optical variability in summer and was dominated by organic matter in both seasons. The geographic variability of CDOM and relationships with dissolved organic carbon (DOC) are also presented. CDOM dominated light absorption at blue wavelengths, contributing 81% (median) of the absorption by all water constituents at 400 nm and 63% at 442 nm. Consequentially, 90% of water-leaving radiance at 412 nm originated from a layer (z90) no deeper than approximately 1.0 m. With water increasingly attenuating light at longer wavelengths, a green peak in light penetration and reflectance is always present in these waters, with z90 up to 3.0–3.5 m depth, whereas z90 only exceeds 5 m at biomass < 5 mg Chla m-3. High absorption combined with a weakly scattering particle population (despite median phytoplankton biomass of 14.1 and 4.3 mg Chla m-3 in spring and summer samples, respectively), characterize this sea as a dark water body for which dedicated or exceptionally robust remote sensing techniques are required. Seasonal and regional optical-biogeochemical models, data distributions, and an extensive set of simulated remote-sensing reflectance spectra for testing of remote sensing algorithms are provided as supplementary data. PMID:28384157

40 CFR 63.1446 - What alternative emission limitation may I meet for my combined gas streams?

Code of Federal Regulations, 2010 CFR

2010-07-01

... than a baghouse or venturi wet scrubber applied to meet any total particulate matter emission limit in... than 5 percent of the total operating time in any semiannual reporting period. (d) For each venturi wet scrubber applied to meet any total particulate matter emission limit in paragraph (b) of this section, you...

Assessment of lead, cadmium, and zinc contamination of roadside soils, surface films, and vegetables in Kampala City, Uganda.

PubMed

Nabulo, Grace; Oryem-Origa, Hannington; Diamond, Miriam

2006-05-01

The relationship between traffic density and trace metal concentrations in roadside soils, surface films, and a selected vegetable weed, Amaranthus dubius Mart. Ex Thell., was determined in 11 farming sites along major highways around Kampala City in Uganda. Surface soil, atmospherically deposited surface films on windows, and leaves of Amaranthus dubius were sampled at known distances from the roads and analyzed for lead (Pb), zinc (Zn), and cadmium (Cd) using flame atomic absorption spectrophotometry. Atmospherically deposited trace metal particulates were sampled using window glass as an inert, passive collector. Total trace metal concentrations in soils ranged from 30.0+/-2.3 to 64.6+/-11.7 mg/kg Pb, 78.4+/-18.4 to 265.6+/-63.2 mg/kg Zn, and 0.8+/-0.13 to 1.40+/-0.16 mg/kg Cd. Total trace metal levels in soil decreased rapidly with distance from the road. Total Pb decreased with distance up to 30 m from the road, where it reached a background soil concentration of 28 mg/kg dry weight. The study found background values of 50 and 1.4 mg/kg for Zn and Cd in roadside soils, respectively. Similarly, Pb concentration in Amaranthus dubius leaves decreased with increasing distance from the road edge. The dominant pathway for Pb contamination was from atmospheric deposition, which was consistent with Pb concentrations in surface films. The mean Pb concentrations in leaves of roadside crops were higher than those in their respective roots, with the highest leaf-to-root ratio observed in the Brassica oleraceae acephala group. The lowest Pb and Zn concentrations were found in the fruit compared to the leaves of the same crops. Leaves of roadside vegetables were therefore considered a potential source of heavy metal contamination to farmers and consumers in urban areas. It is recommended that leafy vegetables should be grown 30 m from roads in high-traffic, urban areas.

Assessment of lead, cadmium, and zinc contamination of roadside soils, surface films, and vegetables in Kampala City, Uganda

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nabulo, Grace; Oryem-Origa, Hannington; Diamond, Miriam

2006-05-15

The relationship between traffic density and trace metal concentrations in roadside soils, surface films, and a selected vegetable weed, Amaranthus dubius Mart. Ex Thell., was determined in 11 farming sites along major highways around Kampala City in Uganda. Surface soil, atmospherically deposited surface films on windows, and leaves of Amaranthus dubius were sampled at known distances from the roads and analyzed for lead (Pb), zinc (Zn), and cadmium (Cd) using flame atomic absorption spectrophotometry. Atmospherically deposited trace metal particulates were sampled using window glass as an inert, passive collector. Total trace metal concentrations in soils ranged from 30.0{+-}2.3 to 64.6{+-}11.7more » mg/kg Pb, 78.4{+-}18.4 to 265.6{+-}63.2 mg/kg Zn, and 0.8{+-}0.13 to 1.40{+-}0.16 mg/kg Cd. Total trace metal levels in soil decreased rapidly with distance from the road. Total Pb decreased with distance up to 30 m from the road, where it reached a background soil concentration of 28 mg/kg dry weight. The study found background values of 50 and 1.4 mg/kg for Zn and Cd in roadside soils, respectively. Similarly, Pb concentration in Amaranthus dubius leaves decreased with increasing distance from the road edge. The dominant pathway for Pb contamination was from atmospheric deposition, which was consistent with Pb concentrations in surface films. The mean Pb concentrations in leaves of roadside crops were higher than those in their respective roots, with the highest leaf-to-root ratio observed in the Brassica oleraceae acephala group. The lowest Pb and Zn concentrations were found in the fruit compared to the leaves of the same crops. Leaves of roadside vegetables were therefore considered a potential source of heavy metal contamination to farmers and consumers in urban areas. It is recommended that leafy vegetables should be grown 30 m from roads in high-traffic, urban areas.« less

Partitioning of total mercury and methylmercury to the colloidal phase in freshwaters.

PubMed

Babiarz, C L; Hurley, J P; Hoffmann, S R; Andren, A W; Shafer, M M; Armstrong, D E

2001-12-15

Using tangential flow ultrafiltration, total mercury (HgT) and methylmercury (MeHg) concentrations in the colloidal phase (0.4 microm-10 kDa) were determined for 15 freshwaters located in the upper Midwest (Minnesota, Michigan, and Wisconsin) and the Southern United States (Georgia and Florida). Unfiltered concentrations were typical of those reported for freshwater and ranged from 0.9 to 27.1 ng L(-1) HgT and from 0.08 to 0.86 ng L(-1) MeHg. For some rivers, HgT and MeHg in the colloidal phase comprised up to 72% of the respective unfiltered concentration. On average, however, HgT and MeHg concentrations were evenly distributed between the particulate (>0.4 microm), colloidal, and dissolved (<10 kDa) phases. The pool of Hg in the colloidal phase decreased with increasing specific conductance. Results from experiments on freshwaters with artificially elevated specific conductance suggest that HgT and MeHg may partition to different subfractions of colloidal material. The colloidal-phase HgT correlation with filtered organic carbon (OC(F)) was generally poor (r2 < 0.14; p > 0.07), but the regression of MeHg with OC(F) was strong, especially in the upper Midwest (r2 = 0.78; p < 0.01). On a mass basis, colloidal-phase Hg concentrations were similar to those of unimpacted sediments in the Midwest. Mercury to carbon ratios averaged 352 pg of HgT/mg of C and 25 pg of MeHg/mg of C and were not correlated to ionic strength. The log of the partition coefficient (log K(D)) for HgT and MeHg ranged from 3.7 to 6.4 and was typical of freshwater values determined using a 0.4 microm cutoff between the particulate phase and the dissolved phase. Log K(D) calculated using the <10 kDa fraction as "dissolved" ranged from 4.3 to 6.6 and had a smaller standard deviation about the mean. In addition, our data support the "particle concentration effect" (PCE) hypothesis that the association of Hg with colloids in the filter-passing fraction can lower the observed log K(D). The similarity between colloidal and particulate-phase partition coefficients suggests that colloidal mass and not preferential colloidal partitioning drives the PCE.

Novel Sampling Techniques for Measurement of Turbine Engine Total Particulate Matter Emissions

EPA Science Inventory

This is the first progress report of a study to evaluate two different condensation devices for the measurement of the total (volatile + non-volatile) particulate matter (PM) emissions from aircraft turbine engines by direct sampling at the engine exit. The characteristics of th...

Nutrient, suspended sediment, and trace element loads in the Blackstone River Basin in Massachusetts and Rhode Island, 2007 to 2009

USGS Publications Warehouse

Zimmerman, Marc J.; Waldron, Marcus C.; DeSimone, Leslie A.

2015-01-01

Analysis of the representative constituents (total phosphorus, total chromium, and suspended sediment) upstream and downstream of impoundments indicated that the existing impoundments, such as Rice City Pond, can be sources of particulate contaminant loads in the Blackstone River. Loads of particulate phosphorus, particulate chromium, and suspended sediment were consistently higher downstream from Rice City Pond than upstream during high-flow events, and there was a positive, linear relation between streamflow and changes in these constituents from upstream to downstream of the impoundment. Thus, particulate contaminants were mobilized from Rice City Pond during high-flow events and transported downstream. In contrast, downstream loads of particulate phosphorus, particulate chromium, and suspended sediment were generally lower than or equal to upstream loads for the former Rockdale Pond impoundment. Sediments associated with the former impoundment at Rockdale Pond, breached in the late 1960s, did not appear to be mobilized during the high-flow events monitored during this study.

Flow and sorption controls of groundwater arsenic in individual boreholes from bedrock aquifers in central Maine, USA

USGS Publications Warehouse

Yang, Qiang; Culbertson, Charles W.; Nielsen, Martha G.; Schalk, Charles W.; Johnson, Carole D.; Marvinney, Robert G.; Stute, Martin; Zheng, Yan

2014-01-01

To understand the hydrogeochemical processes regulating well water arsenic (As) evolution in fractured bedrock aquifers, three domestic wells with [As] up to 478 μg/L are investigated in central Maine. Geophysical logging reveals that fractures near the borehole bottom contribute 70-100% of flow. Borehole and fracture water samples from various depths show significant proportions of As (up to 69%) and Fe (93-99%) in particulates (>0.45 μm). These particulates and those settled after a 16-day batch experiment contain 560-13,000 g/kg of As and 14-35% weight/weight of Fe. As/Fe ratios (2.5-20 mmol/mol) and As partitioning ratios (adsorbed/dissolved [As], 20,000-100,000 L/kg) suggest that As is sorbed onto amorphous hydrous ferric oxides. Newly drilled cores also show enrichment of As (up to 1300 mg/kg) sorbed onto secondary iron minerals on the fracture surfaces. Pumping at high flow rates induces large decreases in particulate As and Fe, a moderate increase in dissolved [As] and As(III)/As ratio, while little change in major ion chemistry. The δD and δ18O are similar for the borehole and fracture waters, suggesting a same source of recharge from atmospheric precipitation. Results support a conceptual model invoking flow and sorption controls on groundwater [As] in fractured bedrock aquifers whereby oxygen infiltration promotes the oxidation of As-bearing sulfides at shallower depths in the oxic portion of the flow path releasing As and Fe; followed by Fe oxidation to form Fe oxyhydroxide particulates, which are transported in fractures and sorb As along the flow path until intercepted by boreholes. In the anoxic portions of the flow path, reductive dissolution of As-sorbed iron particulates could re-mobilize As. For exposure assessment, we recommend sampling of groundwater without filtration to obtain total As concentration in groundwater.

40 CFR 60.155 - Reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (a) The owner or operator of any multiple hearth, fluidized bed, or electric sludge incinerator... kg/Mg (0.75 lb/ton) dry sludge input or less during the most recent performance test, a scrubber... particulate matter emission rate of greater than 0.38 kg/Mg (0.75 lb/ton) dry sludge input during the most...

40 CFR 60.155 - Reporting.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (a) The owner or operator of any multiple hearth, fluidized bed, or electric sludge incinerator... kg/Mg (0.75 lb/ton) dry sludge input or less during the most recent performance test, a scrubber... particulate matter emission rate of greater than 0.38 kg/Mg (0.75 lb/ton) dry sludge input during the most...

40 CFR 60.155 - Reporting.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (a) The owner or operator of any multiple hearth, fluidized bed, or electric sludge incinerator... kg/Mg (0.75 lb/ton) dry sludge input or less during the most recent performance test, a scrubber... particulate matter emission rate of greater than 0.38 kg/Mg (0.75 lb/ton) dry sludge input during the most...

40 CFR 60.155 - Reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (a) The owner or operator of any multiple hearth, fluidized bed, or electric sludge incinerator... kg/Mg (0.75 lb/ton) dry sludge input or less during the most recent performance test, a scrubber... particulate matter emission rate of greater than 0.38 kg/Mg (0.75 lb/ton) dry sludge input during the most...

Microstructural and thermal study of Al-Si-Mg/melon shell ash particulate composite

NASA Astrophysics Data System (ADS)

Abdulwahab, M.; Umaru, O. B.; Bawa, M. A.; Jibo, H. A.

The microstructural study via scanning electron microscope (SEM) and thermal study via differential scanning calorimetric (DSC) study of Al-7%Si-0.3Mg/melon shell ash particulate composite has been carried out. The melon shell ash was used in the production of MMC ranging from 5% to 20% at interval of 5% addition using stir casting method. The melon shell ash was characterized using X-ray fluorescent (XRF) that reveal the presence of CaO, SiO2, Al2O3, MgO, and TiO2 as major compounds. The composite was machined and subjected to heat treatment. Microstructural analyses of the composite produced were done using scanning electron microscope (SEM). The microstructure obtained reveals a dark ceramic (reinforcer) and white metallic phase. Equally, the 5 wt% DSC result gives better thermal conductivity than other proportions (10 wt%, 15 wt%, and 20 wt%). These results showed that an improved property of Al-Si-Mg alloy was achieved using melon shell ash particles as reinforcement up to a maximum of 20 wt% for microstructural and 5% wt DSC respectively.

Parameterization of light absorption by components of seawater in optically complex coastal waters of the Crimea Peninsula (Black Sea).

PubMed

Dmitriev, Egor V; Khomenko, Georges; Chami, Malik; Sokolov, Anton A; Churilova, Tatyana Y; Korotaev, Gennady K

2009-03-01

The absorption of sunlight by oceanic constituents significantly contributes to the spectral distribution of the water-leaving radiance. Here it is shown that current parameterizations of absorption coefficients do not apply to the optically complex waters of the Crimea Peninsula. Based on in situ measurements, parameterizations of phytoplankton, nonalgal, and total particulate absorption coefficients are proposed. Their performance is evaluated using a log-log regression combined with a low-pass filter and the nonlinear least-square method. Statistical significance of the estimated parameters is verified using the bootstrap method. The parameterizations are relevant for chlorophyll a concentrations ranging from 0.45 up to 2 mg/m(3).

Observations on particulate organic nitrates and unidentified components of NO y

NASA Astrophysics Data System (ADS)

Nielsen, Torben; Egeløv, Axel H.; Granby, Kit; Skov, Henrik

A method to determine the total content of particulate organic nitrates (PON) has been developed and ambient air measurements of PON, NO, N02, HNO3, peroxyacetyl nitrate (PAN), peroxypropionyl nitrate (PPN), gas NOY and particulate inorganic nitrate have been performed in the spring and early summer at an agricultural site in Denmark and compared with measurements of ozone, H 2O 2, SO 2, formic acid, acetic acid and methane sulphonic acid. The gas NO y detector determines the sum NO + NO 2 + HNO 2 + HNO 3 + PAN + PPN + gas phase organic nitrates + 2 × N 2O 5 + NO 3. The content of residual gas NO y ( = gas NO y - NO - NO 2 - HNO 3 - PAN - PPN) was determined and a group of unidentified NO y compounds was found. The phenomenon was observed at a site with relatively high NO x/NO y ratios compared to previous observations in U.S.A. and Canada. The residual gas NO y made up 7 ± 6% of total NOY (total NO y = gas NO y + particulate inorganic nitrate). Residual gas NO y was much higher than the particulate fraction of organic nitrates (PON). PON was only 0.25 ± 0.11% of total NO y. Both residual gas NO y and particulate organic nitrates episodes occurred with elevated concentrations of photochemical oxidants in connection with high-pressure systems suggesting atmospheric processes being the major source. Clean marine air can be discarded as a source for PON and residual gas NO y.

Work environments and exposure to hazardous substances in korean tire manufacturing.

PubMed

Lee, Naroo; Lee, Byung-Kyu; Jeong, Sijeong; Yi, Gwang Yong; Shin, Jungah

2012-06-01

The purpose of this study is to evaluate the tire manufacturing work environments extensively and to identify workers' exposure to hazardous substances in various work processes. Personal air sampling was conducted to measure polycyclic aromatic hydrocarbons, carbon disulfide, 1,3-butadiene, styrene, methyl isobutyl ketone, methylcyclohexane, formaldehyde, sulfur dioxide, and rubber fume in tire manufacturing plants using the National Institute for Occupational Safety Health Manual of Analytical Methods. Noise, carbon monoxide, and heat stress exposure were evaluated using direct reading instruments. Past concentrations of rubber fume were assessed using regression analysis of total particulate data from 2003 to 2007, after identifying the correlation between the concentration of total particulate and rubber fume. Workers were exposed to rubber fume that exceeded 0.6 mg/m(3), the maximum exposure limit of the UK, in curing and production management processes. Forty-seven percent of workers were exposed to noise levels exceeding 85 dBA. Workers in the production management process were exposed to 28.1℃ (wet bulb globe temperature value, WBGT value) even when the outdoor atmosphere was 2.7℃ (WBGT value). Exposures to other substances were below the limit of detection or under a tenth of the threshold limit values given by the American Conference of Governmental Industrial Hygienists. To better classify exposure groups and to improve work environments, examining closely at rubber fume components and temperature as risk indicators in tire manufacturing is recommended.

Uncontrolled combustion of shredded tires in a landfill - Part 1: Characterization of gaseous and particulate emissions

NASA Astrophysics Data System (ADS)

Downard, Jared; Singh, Ashish; Bullard, Robert; Jayarathne, Thilina; Rathnayake, Chathurika M.; Simmons, Donald L.; Wels, Brian R.; Spak, Scott N.; Peters, Thomas; Beardsley, Douglas; Stanier, Charles O.; Stone, Elizabeth A.

2015-03-01

In summer 2012, a landfill liner comprising an estimated 1.3 million shredded tires burned in Iowa City, Iowa. During the fire, continuous monitoring and laboratory measurements were used to characterize the gaseous and particulate emissions and to provide new insights into the qualitative nature of the smoke and the quantity of pollutants emitted. Significant enrichments in ambient concentrations of CO, CO2, SO2, particle number (PN), fine particulate (PM2.5) mass, elemental carbon (EC), and polycyclic aromatic hydrocarbons (PAH) were observed. For the first time, PM2.5 from tire combustion was shown to contain PAH with nitrogen heteroatoms (a.k.a. azaarenes) and picene, a compound previously suggested to be unique to coal-burning. Despite prior laboratory studies' findings, metals used in manufacturing tires (i.e. Zn, Pb, Fe) were not detected in coarse particulate matter (PM10) at a distance of 4.2 km downwind. Ambient measurements were used to derive the first in situ fuel-based emission factors (EF) for the uncontrolled open burning of tires, revealing substantial emissions of SO2 (7.1 g kg-1), particle number (3.5 × 1016 kg-1), PM2.5 (5.3 g kg-1), EC (2.37 g kg-1), and 19 individual PAH (totaling 56 mg kg-1). A large degree of variability was observed in day-to-day EF, reflecting a range of flaming and smoldering conditions of the large-scale fire, for which the modified combustion efficiency ranged from 0.85 to 0.98. Recommendations for future research on this under-characterized source are also provided.

Health survey of former workers in a Norwegian coke plant: Part. 1. Estimation of historical exposures

PubMed Central

Romundstad, P. R.; Ronneberg, A.; Leira, H. L.; Bye, T.

1998-01-01

OBJECTIVE: To estimate historical exposure levels at a coke plant for all agents considered to be of importance for epidemiological studies of mortality and cancer incidence. METHODS: Time weighted average exposure (8 h TWA) was estimated based on personal measurements for polycyclic aromatic hydrocarbons (PAHs) and carbonaceous particulates. Exposure to quartz was estimated relative to the concentration of carbonaceous particulates. These estimates were adjusted for the use of airstream helmets. Exposure to other agents were estimated qualitatively (asbestos, benzene, and arsenic) or semi-quantitatively (carbon monoxide (CO) and heat) based on measurements and other indicators of exposure. RESULTS: Exposure to PAHs was highest for those who worked at the top of the ovens (300 micrograms/m3) in the period from 1970-6. The estimated PAH exposure was reduced to an average of 65 micrograms/m3 after the introduction of exposure control measures in 1976. The estimates for carbonaceous particulates ranged from 1 to 16 mg/m3, with the highest exposure for workers at the top of the ovens and at the coke screening station. CONCLUSIONS: The exposure of greatest concern in this study is to PAHs, but exposures to carbonaceous particulates and CO may also be of importance. The major limitations of this study are the lack of personal measurements before 1975 and the total lack of measurements for some of the exposed categories of workers. Despite these limitations, we think that this assessment reflects the actual exposures for most of the former employees. The assessment thus provides a reasonable tool for the subsequent epidemiological study and for future epidemiological follow up studies at the coke plant.   PMID:9861184

Particulate Matter Concentrations in East Oakland's High Street Corridor

NASA Astrophysics Data System (ADS)

Lei, P.; Jackson, J.; Lewis, R.; Marigny, A.; Mitchell, J. D.; Nguyen, R.; Philips, B.; Randle, D.; Romero, D.; Spears, D.; Telles, C.; Weissman, D.

2012-12-01

Particulate matter (PM) is a complex mixture of small solid pieces and/or liquid droplets in the air. High concentrations of PM can pose a serious health hazard because inhalation can result in breathing problems and/or aggravate asthma. Long term exposure can increase the likelihood of respiratory problems like asthma and emphysema as well as cancer. The smaller the particles, the deeper they can get into the respiratory system. For this reason, the smallest particles, those smaller than 2.5 micrometers in diameter (PM2.5), are the most dangerous. PM2.5 is largely emitted from motor vehicles burning fuels that don't break down fully. Our research team investigated the levels of PM2.5 as well as particles smaller than 10 micrometers (PM10) and total suspended particulate (TSP) along the northeast-southwest trending High Street Corridor, near Fremont High School in East Oakland, California. Using the Aerocet 531 mass particle counter, team members walked through neighborhoods and along major roads within a 1 mile radius of Fremont High School. The Aerocet 531 recorded two minute average measurements of all the relevant PM sizes, which are reported in mg/m3. Measurements were consistently taken in the morning, between 8:30 and 11:30 am. Preliminary results indicate maximum readings of all PM sizes at sites that are in close proximity to a major freeway (Interstate-880). These results support our initial hypothesis that proximity to major roads and freeways, especially those with high diesel-fuel burning truck traffic, would be the primary factor affecting PM concentration levels. Preliminary median and maximum readings all suggest particulate matter levels below what the EPA would consider unhealthy or risky.

Uncontrolled combustion of shredded tires in a landfill – Part 1: Characterization of gaseous and particulate emissions

PubMed Central

Downard, Jared; Singh, Ashish; Bullard, Robert; Jayarathne, Thilina; Rathnayake, Chathurika; Simmons, Donald L.; Wels, Brian R.; Spak, Scott N.; Peters, Thomas; Beardsley, Douglas; Stanier, Charles; Stone, Elizabeth A.

2014-01-01

In summer 2012, a landfill liner comprising an estimated 1.3 million shredded tires burned in Iowa City, Iowa. During the fire, continuous monitoring and laboratory measurements were used to characterize the gaseous and particulate emissions and to provide new insights into the qualitative nature of the smoke and the quantity of pollutants emitted. Significant enrichments in ambient concentrations of CO, CO2, SO2, particle number (PN), fine particulate (PM2.5) mass, elemental carbon (EC), and polycyclic aromatic hydrocarbons (PAH) were observed. For the first time, PM2.5 from tire combustion was shown to contain PAH with nitrogen heteroatoms (a.k.a. azaarenes) and picene, a compound previously suggested to be unique to coal-burning. Despite prior laboratory studies’ findings, metals used in manufacturing tires (i.e. Zn, Pb, Fe) were not detected in coarse particulate matter (PM10) at a distance of 4.2 km downwind. Ambient measurements were used to derive the first in situ fuel-based emission factors (EF) for the uncontrolled open burning of tires, revealing substantial emissions of SO2 (7.1 g kg−1), particle number (3.5×1016 kg−1), PM2.5 (5.3 g kg−1), EC (2.37 g kg−1), and 19 individual PAH (totaling 56 mg kg−1). A large degree of variability was observed in day-to-day EF, reflecting a range of flaming and smoldering conditions of the large-scale fire, for which the modified combustion efficiency ranged from 0.85-0.98. Recommendations for future research on this under-characterized source are also provided. PMID:25663800

Effectiveness of radiation synovectomy with samarium-153 particulate hydroxyapatite in rheumatoid arthritis patients with knee synovitis: a controlled randomized double-blind trial.

PubMed

Santos, Marla Francisca dos; Furtado, Rita Nely Vilar; Konai, Monique Sayuri; Castiglioni, Mario Luiz Vieira; Marchetti, Renata Rosa; Natour, Jamil

2009-01-01

The aim of the present study was to investigate the effectiveness of Samarium(153)-particulate hydroxyapatite radiation synovectomy in rheumatoid arthritis patients with chronic knee synovitis. Fifty-eight rheumatoid arthritis patients (60 knees) with chronic knee synovitis participated in a controlled double-blinded trial. Patients were randomized to receive either an intra-articular injection with 40 mg triamcinolone hexacetonide alone (TH group) or 40 mg triamcinolone hexacetonide combined with 15 mCi Samarium(153)-particulate hydroxyapatite (Sm/TH group). Blinded examination at baseline (T0) and at 1 (T1), 4 (T4), 12 (T12), 32 (T32), and 48 (T48) weeks post-intervention were performed on all patients and included a visual analog scale for joint pain and swelling as well as data on morning stiffness, flexion, extension, knee circumference, Likert scale of improvement, percentage of improvement, SF-36 generic quality of life questionnaire, Stanford Health Assessment Questionnaire (HAQ), Lequesne index, use of non-steroidal anti-inflammatory drugs or oral corticosteroids, events and adverse effects, calls to the physician, and hospital visits. The sample was homogeneous at baseline, and there were no withdrawals. Improvement was observed in both groups in relation to T0, but no statistically significant differences between groups were observed regarding all variables at the time points studied. The Sm/TH group exhibited more adverse effects at T1 (p<0.05), but these were mild and transitory. No severe adverse effects were reported during follow-up. Intra-articular injection of Samarium(153)-particulate hydroxyapatite (15 mCi) with 40 mg of triamcinolone hexacetonide is not superior to triamcinolone hexacetonide alone for the treatment of knee synovitis in patients with rheumatoid arthritis at 1 y of follow-up.

Physicochemical characteristics of ambient particles settling upon leaf surfaces of urban plants in Beijing.

PubMed

Wang, Lei; Liu, Lian-you; Gao, Shang-yu; Hasi, Eerdun; Wang, Zhi

2006-01-01

Particulate pollution is a serious health problem throughout the world, exacerbating a wide range of respiratory and vascular illnesses in urban areas. Urban plants play an important role in reducing particulate pollution. Physicochemical characteristics of ambient particles settling upon leaf surfaces of eleven roadside plants at four sites of Beijing were studies. Results showed that density of particles on the leaf surfaces greatly varied with plant species and traffic condition. Fraxinus chinensis, Sophora japonica, A ilanthus altissima, Syringa oblata and Prunus persica had larger densities of particles among the tall species. Due to resuspension of road dust, the densities of particles of Euonymus japonicus and Parthenocissus quinquefolia with low sampling height were 2-35 times to other taller tree species. For test plant species, micro-roughness of leaf surfaces and density of particles showed a close correlation. In general, the larger micro-roughness of leaf surfaces is, the larger density of particles is. Particles settling upon leaf surfaces were dominantly PM, (particulate matter less than 10 microm in aerodynamic diameter; 98.4%) and PM25 (particulate matter less than 2.5 microm in aerodynamic diameter; 64.2%) which were closely relative to human health. Constant elements of particles were C, O, K, Ca, Si, Al, Mg, Na, Fe, S, Cl and minerals with higher content were SiO2, CaCO3, CaMg(CO3)2, NaCI and 2CaSO4 x H20, SiO2. CaCO3 and CaMg(CO3)2 mainly came from resuspension of road dust. 2CaSO4 x H20 was produced by the reaction between CaCO3 derived from earth dust or industrial emission and SO2, H2SO4 or sulfate. NaCl was derived from sea salt.

[Exploration of a quantitative methodology to characterize the retention of PM2.5 and other atmospheric particulate matter by plant leaves: taking Populus tomentosa as an example].

PubMed

Zhang, Zhi-Dan; Xi, Ben-Ye; Cao, Zhi-Guo; Jia, Li-Ming

2014-08-01

Taking Populus tomentosa as an example, a methodology called elution-weighing-particle size-analysis (EWPA) was proposed to evaluate quantitatively the ability of retaining fine particulate matter (PM2.5, diameter d ≤ 2.5 μm) and atmospheric particulate matter by plant leaves using laser particle size analyzer and balance. This method achieved a direct, accurate measurement with superior operability about the quality and particle size distribution of atmospheric particulate matter retained by plant leaves. First, a pre-experiment was taken to test the stability of the method. After cleaning, centrifugation and drying, the particulate matter was collected and weighed, and then its particle size distribution was analyzed by laser particle size analyzer. Finally, the mass of particulate matter retained by unit area of leaf and stand was translated from the leaf area and leaf area index. This method was applied to a P. tomentosa stand which had not experienced rain for 27 days in Beijing Olympic Forest Park. The results showed that the average particle size of the atmospheric particulate matter retained by P. tomentosa was 17.8 μm, and the volume percentages of the retained PM2.5, inhalable particulate matter (PM10, d ≤ 10 μm) and total suspended particle (TSP, d ≤ 100 μm) were 13.7%, 47.2%, and 99.9%, respectively. The masses of PM2.5, PM10, TSP and total particulate matter were 8.88 x 10(-6), 30.6 x 10(-6), 64.7 x 10(-6) and 64.8 x 10(-6) g x cm(-2) respectively. The retention quantities of PM2.5, PM10, TSP and total particulate matter by the P. tomentosa stand were 0.963, 3.32, 7.01 and 7.02 kg x hm(-2), respectively.

The contribution of various types of settling particles to the flux of organic carbon in the Gulf of St. Lawrence

NASA Astrophysics Data System (ADS)

Romero-Ibarra, Nancy; Silverberg, Norman

2011-10-01

The contents of 31 samples from free-drifting sediment traps deployed in the Gulf of St. Lawrence (GSL) were analyzed for the individual contribution of the different types of particles encountered to the total particulate organic carbon (POC) flux. Two trap models were used in 1993-1994: small traps at 50 m depth and large traps at 50 and 150 m. Total POC fluxes averaged 42 mg C m -2 d -1 for the more reliable large trap and 149 mg C m -2 d -1 for the small trap. The POC fluxes were attributed to different classes of particles based upon microscopically determined particle dimensions and carbon/volume algorithms available in the literature. Fecal pellets, followed by phytoplankton, were the major attributable components, with important contributions by microzooplankton, particularly during the summer of 1994. The mean fluxes for pellets (6 and 60 mg C m -2 d -1, for the large and small traps, respectively) and phytoplankton (3.2 and 42.9 mg C m -2 d -1) were in the range of those encountered in other areas of moderate primary productivity. Mean zooplankton carbon fluxes (1.8 and 8.5 mg C m -2 d -1, respectively), however, reflect higher than average zooplankton abundances in the GSL. The C fluxes of specific algal groups confirmed the existence of three trophic regimes previously identified from water column studies and numeric cell fluxes: (1) a period when diatoms were dominant during the spring, (2) a longer interval, which was dominated by dinoflagellates at most others times of the year, and (3) a period of transition during summer. Carbon of animal origin dominated the attributable flux, including an important fraction associated with heterotrophic dinoflagellates. The contribution of marine snow to the total flux (estimated as the difference between the total POC flux and the sum of the attributed components) frequently amounted to more than 60%. The true importance of marine snow remains uncertain, however, because the errors associated with each of the measured components accumulate to produce large uncertainties. The methodological problems involved are discussed.

Investigating the hydrological significance of stalagmite geochemistry (Mg, Sr) using Sr isotope and particulate element records across the Late Glacial-to-Holocene transition

NASA Astrophysics Data System (ADS)

Belli, R.; Borsato, A.; Frisia, S.; Drysdale, R.; Maas, R.; Greig, A.

2017-02-01

The trace element and Sr isotope records in two coeval stalagmites characterized by different growth rates and flow regimes at Savi cave (Grotta Savi, NE Italy) reveal different sources and incorporation mechanisms for Mg and Sr. Mg is sourced primarily from dissolved cave host rock while particulate Mg derived from soil plays a subordinate role. The presence of particulate-borne Mg is inferred from the co-variation of Mg and particle-associated elements (Th, Al and Mn) which are preferentially concentrated in open columnar calcite layers. Variation in Mg concentrations corrected for particle-influenced components, the Mgc parameter, is controlled by water-rock interaction, with higher and lower Mgc during dry and wet phases, respectively. This is thought to reflect incongruent dissolution of Mg-rich phases. Correction of Sr concentrations for contributions from airborne exogenic Sr, based on 87Sr/86Sr ratios, yields the bedrock-only contribution (Src). Src variation in stalagmite calcite is influenced by speleothem growth rate and by variation of the calcite-water Sr partitioning in wet and dry phases, and only to a minor extent by incongruent dissolution of Mg-rich phases. Concentration profiles for Mgc and Srcg (corrected for growth rate effects) show inverse correlations and are inferred to show hydrological significance which is captured in a hydrological index, HI. We suggest HI provides robust information on water-rock interaction related to hydrological changes and can be utilized in both wet and semi-arid environments, provided the corrections for soil Mg and exogenic Sr can be applied with confidence. Application of the HI index allows correction of Grotta Savi oxygen isotope data, to yield a δ18Oc time series that shows when changes in moisture sources and atmospheric reorganization, or changes in moisture amount, were significant. This is especially evident during the Younger Dryas (YD). The Savi record supports the concept of a two-phase YD, marked by an increase of moisture and stronger impact of Adriatic and Mediterranean Sea influences over the northern Adriatic region from 12.3 ka onwards. Then, a large-scale atmospheric reorganization and gradual northward shift of the Polar Front caused a progressive reduction of sea influence over the region from 12.1 ka, supporting the concept of a hemispheric change.

Concentration, solubility and deposition flux of atmospheric particulate nutrients over the Yellow Sea

NASA Astrophysics Data System (ADS)

Shi, Jin-Hui; Zhang, Jing; Gao, Hui-Wang; Tan, Sai-Chun; Yao, Xiao-Hong; Ren, Jing-Ling

2013-12-01

Satellite images showed that two large dust storms swept over the Yellow Sea from 31 Mach to 1 April 2007; both were accompanied by precipitation. Three to four days after the dust episodes, blooms occurred in the Yellow Sea. As an important and potential controlling factor of the bloom, nutrients in the total suspended particle (TSP) and size-segregated particle samples during the cruise campaign were measured and their atmospheric deposition fluxes of nutrients are reported in this paper. Concentrations of total P and TIN (NH4+, NO2- and NO3-) in TSP varied from 0.01 to 1.05 μg m-3, and from 1.21 to 22.28 μg m-3, with the maximum occurring concurrently with the dust storm events. In addition, the measured solubility of Fe in these particles varied from 1.0 to 20.1%, while it ranged from 0.8 to 15% for Al. The total deposition fluxes of Asian dust as well as the contained nutrients were estimated on the basis of an episodic increment of the measured concentration of dissolved Al in the surface ocean during the dust events. The estimated fluxes of atmospheric deposition of soluble Fe, P and inorganic nitrogen over the Yellow Sea during the dust episodes were 42.5±10.9, 10.3±2.6 and 772.0±198.0 mg m-2, respectively. The estimated fluxes of nutrients via dry atmospheric deposition accounted for only ~2% of the total fluxes. The deposition fluxes of particulate Fe and P during the two dust storm events associated with precipitation were about 500-1000 times of that daily averaged flux during non-dust days, indicating the importance of the episodic inputs to the annual budget of these metals deposited into the ocean.

Sources of phosphorus to the Carson River upstream from Lahontan Reservoir, Nevada and California, Water Years 2001-02

USGS Publications Warehouse

Alvarez, Nancy L.; Seiler, Ralph L.

2004-01-01

Discharge of treated municipal-sewage effluent to the Carson River in western Nevada and eastern California ceased by 1987 and resulted in a substantial decrease in phosphorus concentrations in the Carson River. Nonetheless, concentrations of total phosphorus and suspended sediment still commonly exceed beneficial-use criteria established for the Carson River by the Nevada Division of Environmental Protection. Potential sources of phosphorus in the study area include natural inputs from undisturbed soils, erosion of soils and streambanks, construction of low-head dams and their destruction during floods, manure production and grazing by cattle along streambanks, drainage from fields irrigated with streamwater and treated municipal-sewage effluent, ground-water seepage, and urban runoff including inputs from golf courses. In 2000, the U.S. Geological Survey (USGS), in cooperation with Carson Water Subconservancy District, began an investigation with the overall purpose of providing managers and regulators with information necessary to develop and implement total maximum daily loads for the Carson River. Two specific goals of the investigation were (1) to identify those reaches of the Carson River upstream from Lahontan Reservoir where the greatest increases in phosphorus and suspended-sediment concentrations and loading occur, and (2) to identify the most important sources of phosphorus within the reaches of the Carson River where the greatest increases in concentration and loading occur. Total-phosphorus concentrations in surface-water samples collected by USGS in the study area during water years 2001-02 ranged from <0.01 to 1.78 mg/L and dissolved-orthophosphate concentrations ranged from <0.01 to 1.81 mg/L as phosphorus. In streamflow entering Carson Valley from headwater areas in the East Fork Carson River, the majority of samples exceeding the total phosphorus water-quality standard of 0.1 mg/L occur during spring runoff (March, April, and May) when suspended-sediment concentrations are high. Downstream from Carson Valley, almost all samples exceed the water-quality standard, with the greatest concentrations observed during spring and summer months. Estimated annual total-phosphorus loads ranged from 1.33 tons at the West Fork Carson River at Woodfords to 43.41 tons at the Carson River near Carson City during water years 2001-02. Loads are greatest during spring runoff, followed by fall and winter, and least during the summer, which corresponds to the amount of streamflow in the Carson River. The estimated average annual phosphorus load entering Carson Valley was 21.9 tons; whereas, the estimated average annual phosphorus load leaving Carson Valley was 37.8 tons, for an annual gain in load across Carson Valley of 15.9 tons. Thus, about 58 percent of the total-phosphorus load leaving Carson Valley on an annual basis could be attributed to headwater reaches upstream from Carson Valley. During spring and summer (April 1-September 30) an average of 85 percent of the total-phosphorus load leaving Carson Valley could be attributed to headwater reaches. During fall and winter (October 1-March 31) only 17 percent of the phosphorus load leaving Carson Valley could be attributed to headwater reaches. The composition of the phosphorus changes during summer from particulate phosphorus entering Carson Valley to dissolved orthophosphate leaving Carson Valley. Particulate phosphorus entering Carson Valley could be settling out when water is applied to fields and be replaced by dissolved orthophosphate from other sources. Alternatively, the particulate phosphorus could be converted to dissolved orthophosphate as it travels across Carson Valley. Data collected during the study are not sufficient to distinguish between the two possibilities. Eagle Valley and Dayton-Churchill Valleys may act as sinks for phosphorus. On an annual basis, during water years 2001-02, about 90 percent of the phosphorus entering Eagle Valley left the

The relationship of blood- and urine-boron to boron exposure in borax-workers and usefulness of urine-boron as an exposure marker.

PubMed Central

Culver, B D; Shen, P T; Taylor, T H; Lee-Feldstein, A; Anton-Culver, H; Strong, P L

1994-01-01

Daily dietary-boron intake and on-the-job inspired boron were compared with blood- and urine-boron concentrations in workers engaged in packaging and shipping borax. Fourteen workers handling borax at jobs of low, medium, and high dust exposures were sampled throughout full shifts for 5 consecutive days each. Airborne borax concentrations ranged from means of 3.3 mg/m3 to 18 mg/m3, measured gravimetrically. End-of-shift mean blood-boron concentrations ranged from 0.11 to 0.26 microgram/g; end-of-shift mean urine concentrations ranged from 3.16 to 10.72 micrograms/mg creatinine. Creatinine measures were used to adjust for differences in urine-specific gravity such that 1 ml of urine contains approximately 1 mg creatinine. There was no progressive increase in end-of-shift blood- or urine-boron concentrations across the days of the week. Urine testing done at the end of the work shift gave a somewhat better estimate of borate exposure than did blood testing, was sampled more easily, and was analytically less difficult to perform. Personal air samplers of two types were used: one, the 37-mm closed-face, two-piece cassette to estimate total dust and the other, the Institute of Occupational Medicine (IOM) sampler to estimate inspirable particulate mass. Under the conditions of this study, the IOM air sampler more nearly estimated human exposure as measured by blood- and urine-boron levels than did the sampler that measured total dust.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7889874

Controlling tailwater sediment and phosphorus concentrations with polyacrylamide in the Imperial Valley, California.

PubMed

Goodson, Christopher C; Schwartz, Gregory; Amrhein, Christopher

2006-01-01

External loading of phosphorus (P) from agricultural surface discharge (tailwater) is the main cause of excessive algae growth and the eutrophication of the Salton Sea, California. Continuous polyacrylamide (PAM) applications to agricultural irrigation water inflows were evaluated as a means of reducing sediment and P in tailwater. Zero (control) and 1 mg L(-1) PAM (PAM1) treatments were compared at 17 Imperial Valley field sites. Five and 10 mg L(-1) PAM treatments (PAM5, PAM10) were conducted at one site. The particulate phosphorus (Pp) fraction was determined as the difference between total phosphorus (Pt) and the soluble phosphorus (Ps) fraction. We observed 73, 82, and 98% turbidity reduction with PAM1, PAM5, and PAM10 treatments. Although eight field sites had control tailwater sediment concentrations above the New River total maximum daily loads (TMDL), all but one were made compliant during their paired PAM1 treatments. While PAM1 and PAM10 reduced tail water Pp by 31 and 78%, none of the treatments tested reduced Ps. This may have been caused by high irrigation water Na concentrations which would reduce Ca adsorption and Ca-phosphate bridging on the PAM. The PAM1 treatments resulted in <0.5 mg L(-1) drain water polyacrylamide concentrations 1.6 km downstream of PAM addition, while PAM5 and PAM10 treatments produced > 2 mg L(-1) drain water polyacrylamide concentrations. We concluded that, although PAM practically eliminates Imperial Valley tailwater sediment loads, it does not effectively reduce tailwater Ps, the P fraction most responsible for the eutrophication of the Salton Sea.

Design and evaluation of a low-volume total suspended particulate sampler

USDA-ARS?s Scientific Manuscript database

The regulation of particulate matter (PM) emitted by agricultural sources, e.g., cotton gins, feed mills, and concentrated animal feeding operations (CAFOs), is based on downwind concentrations of particulate matter less than 10 and 2.5 'm (PM10 and PM2.5) aerodynamic equivalent diameter (AED). Both...

Battery condenser system particulate emission factors for cotton gins: Particle size distribution characteristics

USDA-ARS?s Scientific Manuscript database

This report is part of a project to characterize cotton gin emissions from the standpoint of total particulate stack sampling and particle size analyses. In 2013, the Environmental Protection Agency (EPA) published a more stringent standard for particulate matter with nominal diameter less than or e...

Fugitive emission rates assessment of PM2.5 and PM10 from open storage piles in China

NASA Astrophysics Data System (ADS)

Cao, Yiqi; Liu, Tao; He, Jiao

2018-03-01

An assessment of the fugitive emission rates of PM2.5 and PM10 from an open static coal and mine storage piles. The experiment was conducted at a large union steel enterprises in the East China region to effectively control the fugitive particulate emissions pollution on daily work and extreme weather conditions. Wind tunnel experiments conducted on the surface of static storage piles, and it generated specific fugitive emission rates (SERs) at ground level of between ca.10-1 and ca.102 (mg/m2·s) for PM2.5 and between ca.101 and ca.103 (mg/m2·s) for PM10 under the u*(wind velocity) between ca.3.0 (m/s) and 10.0 (m/s). Research results show that SERs of different materials differ a lot. Material particulate that has lower surface moisture content generate higher SER and coal material generate higher SER than mine material. For material storage piles with good water infiltrating properties, aspersion is a very effective measure for control fugitive particulate emission.

Synthesis and Characterization of Nano Boron Nitride Reinforced Magnesium Composites Produced by the Microwave Sintering Method

PubMed Central

Seetharaman, Sankaranarayanan; Subramanian, Jayalakshmi; Tun, Khin Sandar; Hamouda, Abdelmagid S.; Gupta, Manoj

2013-01-01

In this study, magnesium composites with nano-size boron nitride (BN) particulates of varying contents were synthesized using the powder metallurgy (PM) technique incorporating microwave-assisted two-directional sintering followed by hot extrusion. The effect of nano-BN addition on the microstructural and the mechanical behavior of the developed Mg/BN composites were studied in comparison with pure Mg using the structure-property correlation. Microstructural characterization revealed uniform distribution of nano-BN particulates and marginal grain refinement. The coefficient of thermal expansion (CTE) value of the magnesium matrix was improved with the addition of nano-sized BN particulates. The results of XRD studies indicate basal texture weakening with an increase in nano-BN addition. The composites showed improved mechanical properties measured under micro-indentation, tension and compression loading. While the tensile yield strength improvement was marginal, a significant increase in compressive yield strength was observed. This resulted in the reduction of tension-compression yield asymmetry and can be attributed to the weakening of the strong basal texture. PMID:28809252

Performance of an Anaerobic Baffled Reactor (ABR) in treatment of cassava wastewater

PubMed Central

Ferraz, Fernanda M.; Bruni, Aline T.; Del Bianchi, Vanildo L.

2009-01-01

The performance of an anaerobic baffled reactor (ABR) was evaluated in the treatment of cassava wastewater, a pollutant residue. An ABR divided in four equal volume compartments (total volume 4L) and operated at 35ºC was used in cassava wastewater treatment. Feed tank chemical oxygen demand (COD) was varied from 2000 to 7000 mg L-1 and it was evaluated the most appropriated hydraulic retention time (HRT) for the best performance on COD removal. The ABR was evaluated by analysis of COD (colorimetric method), pH, turbidity, total and volatile solids, alkalinity and acidity. Principal component analysis (PCA) was carried to better understand data obtained. The system showed buffering ability as acidity decreased along compartments while alkalinity and pH values were increased. There was particulate material retention and COD removal varied from 83 to 92% for HRT of 3.5 days. PMID:24031316

Emission characteristics for gaseous- and size-segregated particulate PAHs in coal combustion flue gas from circulating fluidized bed (CFB) boiler.

PubMed

Wang, Ruwei; Liu, Guijian; Sun, Ruoyu; Yousaf, Balal; Wang, Jizhong; Liu, Rongqiong; Zhang, Hong

2018-07-01

The partitioning behavior of polycyclic aromatic hydrocarbons (PAHs) between gaseous and particulate phases from coal-fired power plants (CFPPs) is critically important to predict PAH removal by dust control devices. In this study, 16 US-EPA priority PAHs in gaseous and size-segregated particulate phases at the inlet and outlet of the fabric filter unit (FFs) of a circulating fluidized bed (CFB) boiler were analyzed. The partitioning mechanisms of PAHs between gaseous and particulate phases and in particles of different size classes were investigated. We found that the removal efficiencies of PAHs are 45.59% and 70.67-89.06% for gaseous and particulate phases, respectively. The gaseous phase mainly contains low molecular weight (LMW) PAHs (2- and 3-ring PAHs), which is quite different from the particulate phase that mainly contains medium and high molecular weight (MMW and HMW) PAHs (4- to 6-ring PAHs). The fractions of LMW PAHs show a declining trend with the decrease of particle size. The gas-particle partitioning of PAHs is primarily controlled by organic carbon absorption, in addition, it has a clear dependence on the particle sizes. Plot of log (TPAH/PM) against logD p shows that all slope values were below -1, suggesting that PAHs were mainly adsorbed to particulates. The adsorption effect of PAHs in size-segregated PMs for HMW PAHs is more evident than LMW PAHs. The particle size distributions (PSDs) of individual PAHs show that most of PAHs exhibit bi-model structures, with one mode peaking in the accumulation size range (2.1-1.1 μm) and another mode peaking in coarse size range (5.8-4.7 μm). The intensities of these two peaks vary in function of ring number of PAHs, which is likely attributed to Kelvin effect that the less volatile HMW PAH species preferentially condense onto the finer particulates. The emission factor of PAHs was calculated as 3.53 mg/kg of coal burned, with overall mean EF PAH of 0.55 and 2.98 mg/kg for gaseous and particulate phase, respectively. Moreover, the average emission amount of PAHs for the investigated CFPP was 1016.6 g/day and 371073.6 g/y, respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

Investigation of selenium pretreatment in the attenuation of lung injury in rats induced by fine particulate matters.

PubMed

Liu, Jie; Yang, Yingying; Zeng, Xuejiao; Bo, Liang; Jiang, Shuo; Du, Xihao; Xie, Yuquan; Jiang, Rongfang; Zhao, Jinzhuo; Song, Weimin

2017-02-01

Selenium (Se) is vital for health because of its antioxidative and anti-inflammation functions. The aim of this study was to determine if dietary selenium could inhibit the rat lung injury induced by ambient fine particulate matter (PM 2.5 ). Sprague-Dawley rats were randomly allocated in seven groups (n = 8). The rats in PM 2.5 exposure group were intratracheally instilled with 40 mg/kg of body weight (b.w.) of PM 2.5 suspension. The rats in Se prevention groups were pretreated with 17.5, 35, or 70 μg/kg b.w. of Se for 4 weeks, respectively. Then, the rats were exposed to 40 mg/kg b.w. of PM 2.5 in the fifth week. The bronchoalveolar lavage fluid (BALF) was collected to count the neutrophil numbers and to analyze the cytokines (tumor necrosis factor-α (TNF-α), interleukin-1β (IL-1β), soluble intercellular adhesion molecule-1 (sICAM-1)) related to inflammation, the markers related to oxidative stress (total antioxidant capacity (T-AOC), total superoxide dismutase (T-SOD), glutathione peroxidase (GSH-Px), and malondialdehyde (MDA)), and the indicators related to cell damage (lactate dehydrogenase (LDH), total protein (TP), alkaline phosphatase (AKP)). The lung lobe that has not undergone bronchoalveolar lavage was processed for light microscopic examination. The results showed that the proportions of neutrophils in the BALF and the pathologic scores of the lung in PM 2.5 -exposed groups were higher than that in the control group (P < 0.05). Se pretreatment caused a dose-dependent decrease in TNF-α, IL-1β, sICAM-1, LDH, TP, AKP, and MDA when compared with the PM 2.5 -only exposure group. Meanwhile, the dose-dependent increase in T-AOC, T-SOD, and GSH-Px activities were observed in rats pretreated with Se. In conclusion, Se pretreatment may protect rat lungs against inflammation and oxidative stress induced by PM 2.5 , which suggests that Se plays an important role as a kind of potential preventative agent to inhibit the PM 2.5 -induced lung injury.

The molecular distribution of fine particulate organic matter emitted from Western-style fast food cooking

NASA Astrophysics Data System (ADS)

Zhao, Yunliang; Hu, Min; Slanina, Sjaak; Zhang, Yuanhang

The emissions from food cooking could be a significant contributor to atmospheric particulate organic matter (POM) and its chemical composition would vary with different cooking styles. In this study, the chemical composition of POM emitted from Western-style fast food cooking was investigated. A total of six PM 2.5 samples was collected from a commercial restaurant and determined by gas chromatography-mass spectrometry (GC-MS). It is found that the total amount of quantified compounds of per mg POM in Western-style fast food cooking is much higher than that in Chinese cooking. The predominant homologue is fatty acids, accounting for 78% of total quantified POM, with the predominant one being palmitic acid. Dicarboxylic acids display the second highest concentration in the quantified homologues with hexanedioic acid being predominant, followed by nonanedioic acid. Cmax of n-alkanes occurs at C25, but they still appear relative higher concentrations at C29 and C31. In addition, both levoglucosan and cholesterol are quantified. The relationship of concentrations of unsaturated fatty acids (C16 and C18) with a double bond at C9 position and C9 acids indicates the reduction of the unsaturated fatty acids in the emissions could form the C9 acids. Moreover, the nonlinear fit indicates that other C9 species or other compounds are also produced, except for the C9 acids. The potential candidates of tracers for the emissions from Western-fast food cooking could be: tetradecanoic acid, hexadecanoic acid, octadecanoic acid, 9-octadecenoic acid, nonanal, lactones, levoglucosan, hexanedioic acid and nonanedioic acid.

2010 Lead (Pb) Air Monitoring Requirements & 2013 Method for Determination of Lead (Pb) in Total Suspended Particulate Matter Fact Sheets

EPA Pesticide Factsheets

This page contains a variety of fact sheets and other documents that are supplementary to the 2010 final revisions to lead (Pb) ambient air monitoring requirements and the 2013 final method for determination of Pb in total suspended particulate matter.

78 FR 22501 - Designation of Areas for Air Quality Planning Purposes; State of Nevada; Total Suspended Particulate

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-16

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 81 [EPA-R09-OAR-2013-0104; FRL-9802-5] Designation of Areas for Air Quality Planning Purposes; State of Nevada; Total Suspended Particulate AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule. SUMMARY: EPA is proposing to delete certain area...

Distribution and source of rare earth elements in PM2.5 in Xiamen, China.

PubMed

Wang, Shanshan; Yu, Ruilian; Hu, Gongren; Hu, Qichao; Zheng, Quan

2017-12-01

Particulate matter with diameter ≤2.5 µm (PM 2.5 ) is a serious atmospheric pollutant. Composition and source analyses are essential for controlling PM 2.5 . Rare earth elements (REEs) have received little attention as a component of PM 2.5 . In the present study, PM 2.5 samples were collected in urban and suburban areas in Xiamen and analyzed for REEs. The concentration range of total REEs (∑REE) is 12.07 to 98.45 mg/kg, with a mean of 38.53 mg/kg, in urban PM 2.5 and 16.44 to 160.62 mg/kg, with a mean of 42.94 mg/kg, in suburban PM 2.5 . Light REE concentrations are higher in suburban PM 2.5 , whereas heavy REE concentrations are higher in urban PM 2.5 , implying distinct sources of REEs in urban and suburban PM 2.5 . The scatter plots of δEu-∑REE and La-Ce-Sm suggest that REEs in urban PM 2.5 originate from gasoline- and diesel-vehicle exhaust, whereas those in suburban PM 2.5 are mainly influenced by gasoline-vehicle exhaust. Environ Toxicol Chem 2017;36:3217-3222. © 2017 SETAC. © 2017 SETAC.

Enhancing overall tensile and compressive response of pure Mg using nano-TiB{sub 2} particulates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meenashisundaram, Ganesh Kumar; Seetharaman, Sankaranarayanan; Gupta, Manoj, E-mail: mpegm@nus.edu.sg

2014-08-15

A novel attempt is made to synthesize and study the isolated effects of less than two volume fraction TiB{sub 2} nanoparticulates (60 nm) on pure magnesium. New light weight Mg–TiB{sub 2} nanocomposites with superior mechanical properties compared to pure magnesium are synthesized using disintegrated melt deposition technique followed by hot extrusion. The microstructural characterization studies revealed that the samples exhibited fairly uniform distribution of TiB{sub 2} nanoparticulates with minimal porosity and good interfacial integrity between Mg matrix and TiB{sub 2} particulates. The coefficient of thermal expansion results indicates that the addition of 0.58, 0.97, and 1.98 vol.% TiB{sub 2} nanoparticulatesmore » marginally improves the dimensional stability of pure magnesium. A significant improvement in the room temperature tensile properties of pure magnesium was observed with the addition of less than two volume fraction TiB{sub 2} nanoparticulates. The synthesized Mg 1.98 vol.% TiB{sub 2} nanocomposite revealed the best room temperature tensile properties with a significant increase in the 0.2% tensile yield strength by ∼ 54%, ultimate tensile strength by ∼ 15% and fracture strain by ∼ 79% when compared to pure Mg. The X-ray diffraction studies indicated changes in the basal plane orientation of pure Mg with the addition of nano-TiB{sub 2} particulates. A maximum tensile fracture strain of ∼ 16% is achieved with the addition of 0.97 vol.% TiB{sub 2}. The room temperature compressive properties of the nanocomposites reveal that the addition of 1.98 TiB{sub 2} increases the 0.2% compressive yield strength of Mg by ∼ 47% and ultimate compressive strength by ∼ 10% with a marginal increase in the fracture strain (∼ 11%). Reduction in tensile–compression yield asymmetry was observed for Mg 0.58 and 0.97 vol.% TiB{sub 2} nanocomposites which can be attributed to the weakening of the strong basal texture of pure Mg. - Highlights: • First attempt is made to synthesize and characterize Mg-TiB{sub 2} nanocomposites. • XRD studies indicate nano TiB{sub 2} addition modifies the basal texture of pure Mg. • Maximum tensile fracture strain of ∼ 16 % in Mg 0.97 vol.% TiB{sub 2} nanocomposite. • Hardness values of Mg-TiB{sub 2} composites indicate superior tribological properties.« less

Sampling, testing and modeling particle size distribution in urban catch basins.

PubMed

Garofalo, G; Carbone, M; Piro, P

2014-01-01

The study analyzed the particle size distribution of particulate matter (PM) retained in two catch basins located, respectively, near a parking lot and a traffic intersection with common high levels of traffic activity. Also, the treatment performance of a filter medium was evaluated by laboratory testing. The experimental treatment results and the field data were then used as inputs to a numerical model which described on a qualitative basis the hydrological response of the two catchments draining into each catch basin, respectively, and the quality of treatment provided by the filter during the measured rainfall. The results show that PM concentrations were on average around 300 mg/L (parking lot site) and 400 mg/L (road site) for the 10 rainfall-runoff events observed. PM with a particle diameter of <45 μm represented 40-50% of the total PM mass. The numerical model showed that a catch basin with a filter unit can remove 30 to 40% of the PM load depending on the storm characteristics.

Acute Decrease in HDL Cholesterol Associated With Exposure to Welding Fumes

PubMed Central

Rice, Mary Berlik; Cavallari, Jenn; Fang, Shona; Christiani, David

2011-01-01

Objective To investigate acute changes in circulating lipids after exposure to relatively high levels of particulate matter through welding. Methods Using a repeated measures panel study, lipid levels before and after welding and personal exposures to fine particulate matter (PM2.5) were measured in 36 male welders over 63 exposure and/or control days. Results There was a trend toward decrease in HDL (−2.3 mg/dL, P = 0.08) 18 hours after welding. This effect became significant (−2.6 mg/dL, P = 0.05) after adjustment for possible confounders. The effect was strongest (−4.3 mg/dL, P = 0.02) among welders who did not weld the day before the study. There were no significant changes in other lipids associated with welding or PM2.5 exposure. Conclusion Welding exposure was associated with an acute decrease in circulating HDL, which may relate to the inflammatory and proatherosclerotic effects of fine particle exposure. PMID:21187793

Clean-burning diesel engines. Interim report, June-December 1985 on Phase 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dietzmann, H.E.; Smith, L.R.

Gaseous and particulate emissions were measured from diesel forklift engines under a variety of steady-state conditions. An EPA certification fuel was used to determine CO, CO/sub 2/, NOx, HC, particulate, aldehydes, smoke and SO/sub 2/ emission rates from Isuzu C-240, Peugeot XD3P, and Teledyne TMD-20 diesel engines. Emission rates were reported in b/hp-hr, g/hr, and observed concentration, i.e., ppm, percent, or mg/cu. m.

Using oily wastewater emulsified fuel in boiler: energy saving and reduction of air pollutant emissions.

PubMed

Chen, Chun-Chi; Lee, Wen-Jhy

2008-01-01

The limited data for using emulsified oil have demonstrated its effectiveness in reducing flue gas pollutant emissions. The presence of a high concentration of toxic organic compounds in industrial wastewaters always presents significant problems. Therefore, this study was undertaken by using wastewater with COD of 9600 mg/L and total petroleum hydrocarbons-gasoline 440 mg/L for making an emulsified oil (wastewater content 20% with 0.1% surfactant) to evaluate the extent of reductions in both criteria pollutants and polycyclic aromatic hydrocarbons. For comparison, two other systems (heavy oil fuel and water-emulsified oil) were also conducted. The wastewater-emulsified oil fuel results in significant reductions in particulate matter (PM), NO(x), SO2, and CO as compared to heavy oil fuel and similar to those from water/oil emulsified fuel; for PM, it is better in wastewater-emulsified oil. The reductions of total PAH flue gas emissions are 38 and 30% for wastewater- and water-emulsified fuel, respectively; they are 63 and 44% for total BaP(eq), respectively. In addition to reducing flue gas pollutant emissions, the results also demonstrate that the use of wastewater-emulsified fuel in boiler operation provides several advantages: (1) safe disposal of industrial wastewater; and (2) energy savings of about 13%. Thus, wastewater/oil-emulsified fuel is highly suitable for use in boilers.

[Distribution of organic carbon and carbon fixed strength of phytoplankton in Enteromorpha prolifera outbreak area of the Western South Yellow Sea, 2008].

PubMed

Xia, Bin; Ma, Shao-Sai; Chen, Ju-Fa; Zhao, Jun; Chen, Bi-Juan; Wang, Fang

2010-06-01

Based on the analysis of dissolved organic carbon (DOC), particulate organic carbon (POC) and particulate nitrogen (PN) of the samples collected from stations in Enteromorpha prolifera outbreak area of the Western South Yellow Sea during the period August 9-13 of 2008, combining with the data of environmental hydrology, the horizontal distribution, source and influential factors of organic carbon and carbon fixed strength of phytoplankton were discussed. The results showed that the concentrations of DOC and POC ranged from 1.55 mg/L to 3.22 mg/L, 0.11 mg/L to 0.68 mg/L, with average values of 2.44 mg/L and 0.27 mg/L. The horizontal distributions of DOC and POC were similar in study area. The concentrations of DOC and POC in coastal area were higher than that in the outer sea and the concentrations of DOC and POC at surface water layer were higher than those at the bottom water layer. There were a positive correlation between POC and TSS, indicating that the concentrations and source of TSS were main factors for the POC. According to the univariate linear regression model between POC and PN, the concentrations of particulate inorganic nitrogen (PIN) were evaluated. Removing the content of PIN in the samples, the average POC/PON values in most coastal waters were less than 8, combining with the values of POC/chlorophyll a, suggesting that the marine primary production were the important source of POC in most coastal waters, and the presence of degraded organic matter which derived from degraded Enteromorph prolifera was in the latter period of green tide outbreak. The results of evaluated carbon fixed strength based on primary productivity showed that carbon fixed strength of phytoplankton in Enteromorpha prolifera outbreak area of the Western South Yellow Sea ranged from 167 mg/(m2 x d) to 2017 mg/(m2 x d), with the average of 730 mg/(m2 x d). The daily carbon fixed quantities of the study area were up to 2.95 x 10(4) t. Then the daily carbon fixed quantities of the Yellow Sea were 28.03 x 10(4) t.

Carbonaceous aerosols in fine particulate matter of Santiago Metropolitan Area, Chile.

PubMed

Toro Araya, Richard; Flocchini, Robert; Morales Segura, Rául G E; Leiva Guzmán, Manuel A

2014-01-01

Measurements of carbonaceous aerosols in South American cities are limited, and most existing data are of short term and limited to only a few locations. For 6 years (2002-2007), concentrations of fine particulate matter and organic and elemental carbon were measured continuously in the capital of Chile. The contribution of carbonaceous aerosols to the primary and secondary fractions was estimated at three different sampling sites and in the warm and cool seasons. The results demonstrate that there are significant differences in the levels in both the cold (March to August) and warm (September to February) seasons at all sites studied. The percent contribution of total carbonaceous aerosol fine particulate matter was greater in the cool season (53 ± 41%) than in the warm season (44 ± 18%). On average, the secondary organic carbon in the city corresponded to 29% of the total organic carbon. In cold periods, this proportion may reach an average of 38%. A comparison of the results with the air quality standards for fine particulate matter indicates that the total carbonaceous fraction alone exceeds the World Health Organization standard (10 µg/m(3)) and the United States Environmental Protection Agency standard (15 µg/m(3)) for fine particulate matter.

The Physical Clogging of the Landfill Leachate Collection System in China: Based on Filtration Test and Numerical Modelling

PubMed Central

Sun, Weixin; Liu, Jianguo

2018-01-01

Clogging of the leachate collection system (LCS) has been a common operation problem in municipal solid waste (MSW) landfills in China, which can result in high water levels that threaten the safety of landfill operations. To determine the cause of failure in an LCS, raw leachate from a municipal solid waste transfer station was collected and the high content of particulate matter was characterized. Based on the parameters obtained in a filtration test, a numerical simulation was performed to estimate the influence of particle deposition on drainage system clogging. The results showed that LCSs were confronted with the risk of clogging due to the deposition of particulate matter resulting from the higher concentration of total suspended solids (TSS level > 2200 mg L−1) and larger particle size (>30% TSS particles > 15 μm) in the leachate. On one hand, the non-woven geotextile, as the upper layer of the LCS, retained most particulate matter of large diameters, reducing its hydraulic conductivity to approximately 10−8 to 10−9 m s−1 after 1–2 years of operation and perching significant leachate above it (0.6–0.7 m). On the other hand, the geotextile prevented the gravel layer from physically clogging and minimized the leachate head above the bottom liner. Therefore, the role of geotextile should be balanced to optimize the LCS in MSW landfills in China. PMID:29439538

Soluble Ions with ICP-MS are Superior to Total Elements with XRF in Assessing Component-specific Cardiovascular Effects of Fine Particulate Matter

EPA Science Inventory

Background: We previously reported that total fine particulate matter (PM2.5) was associated with flow-mediated dilation (FMD), interleukin-6 (lL-6) and tumor-necrosisfactor-alpha (TNFa) in 22 individuals with type 2 diabetes. Objectives: We now compare two laboratory methods of ...

Assessment of suspended solids concentration in highway runoff and its treatment implication.

PubMed

Hallberg, M; Renman, G

2006-09-01

It is understood that the major pollution from storm water is related to the content of particulate matter. One treatment practice is based on the first flush, i.e. detention of the initial part of the runoff that is considered to contain the highest concentrations of pollutants. This study has evaluated the concentration of total suspended solids in 30 consecutive runoff events during the winter season for an area of 6.7 hectares. A six-lane highway (E4) that has an annual average daily traffic load of 120,000 dominates the area and road de-icing salt (NaCl) and studded tires were in regular use during the studied period. The effluent standard for wastewater of 60 mg TSS per litre applied in EU was used to assess the treatment requirement of storm water. In only two of the events the event mean concentration was below 60 mg 1(-1). In four runoff events a partial event mean concentration below 60 mg 1(-1) was found, in 26 %, 12 %, 11 %, and 2 % respectively of the runoff volume. This would suggest that a capture of the initial part of the runoff for subsequent treatment is less applicable in this type of urban watershed.

Assessment of the Particulate Food Supply Available for Mussel ( Mytilus spp.) Farming in a Semi-enclosed, Northern Inlet

NASA Astrophysics Data System (ADS)

Penney, R. W.; McKenzie, C. H.; Mills, T. J.

2001-07-01

Temporal variability in the quantity, organic content, and phytoplankton composition of the particulate food supply available to a cultured mussel population was assessed for a 3-year period in a small inlet of Notre Dame Bay, Newfoundland, Canada. The study site had a restricted flushing rate estimated at 1-2·75 times wk -1for a complete water exchange. The quantity of both total (TPM) and organic (POM) seston varied temporally from 0·7-23·7 mg l -1and 0·05-1·97 mg l -1respectively during the 3-year sampling period. TPM typically remained relatively high (>10 mg l -1) through the winter and spring period. Most of the seasonal variation in total seston was due to seasonal variability in the PIM component. Both PIM and POM concentrations were seasonally lowest during summer. The organic fraction of the seston (POM/TPM ratio) was seasonally low in winter and increased steadily through spring and summer to reach its maximum in the autumn. The living phytoplankton component of the seston was typically dominated, both numerically and in biomass, by a variety of diatom and autotrophic nanoflagellate species in the 2- 20-μm diameter size range. Discrete diatom population blooms occurred in the autumn of all three years and largely consisted of a single species, Skeletonema costatum. Phytoplankton:detritus ratios were significantly lower during winter. Total phytoplankton biomass levels were seasonally low during winter and summer and were associated with seasonal variation in diatom biomass. We conducted modelling simulations of relationships among seston organic food levels, their temporal variability, tidal flushing rates, cultured mussel biomass and production indices, and estimates of mussel maintenance ration requirements to predict the adequacy of northern inlets to sustain commercial-scale mussel farm development. We conclude from these simulations that small, semi-enclosed, northern inlets likely frequently experience periods when naturally occurring organic seston levels are insufficient to meet basic mussel stock maintenance ration requirements when such inlets are stocked to commercial-scale densities. We infer that periods of food-limited mussel growth and/or production are likely to occur at these high mussel population levels, particularly during summer. Qualitatively poor (low POM:TPM ratio; low phytoplankton:detritus ratio) food supply during winter may also be a further limiting factor. The implications of our conclusions in relation to aquaculture industry development and environmental management are discussed.

A Study on Characteristics of Atmospheric Heavy Metals in Subway Station

PubMed Central

Kim, Chun-Huem; Yoo, Dong-Chul; Kwon, Young-Min; Han, Woong-Soo; Kim, Gi-Sun; Park, Mi-Jung; Kim, Young Soon

2010-01-01

In this study, we investigated the atmospheric heavy metal concentrations in the particulate matter inside the subway stations of Seoul. In particular, we examined the correlation between the heavy metals and studied the effect of the heavy metals on cell proliferation. In six selected subway stations in Seoul, particulate matter was captured at the platforms and 11 types of heavy metals were analyzed. The results showed that the mean concentration of iron was the highest out of the heavy metals in particulate matter, followed by copper, potassium, calcium, zinc, nickel, sodium, manganese, magnesium, chromium and cadmium in that order. The correlation analysis showed that the correlations between the heavy metals was highest in the following order: (Cu vs Zn) , (Ca vs Na) , (Ca vs Mn) , (Ni vs Cr) , (Na vs Mn) , (Cr vs Cd) , (Zn vs Cd) , (Cu vs Cd) , (Ni vs Cd) , (Cu vs Ni) , (K vs Zn) , (Cu vs K) , (Cu vs Cr) , (K vs Cd) , (Zn vs Cr) , (K vs Ni) , (Zn vs Ni) , (K vs Cr) , and (Fe vs Cu) . The correlation coefficient between zinc and copper was 0.937, indicating the highest correlation. Copper, zinc, nickel, chromium and cadmium, which are generated from artificial sources in general, showed correlations with many of the other metals and the correlation coefficients were also relatively high. The effect of the heavy metals on cell proliferation was also investigated in this study. Cultured cell was exposed to 10 mg/l or 100 mg/l of iron, copper, calcium, zinc, nickel, manganese, magnesium, chromium and cadmium for 24 hours. The cell proliferation in all the heavy metal-treated groups was not inhibited at 10 mg/l of the heavy metal concentration. The only exception to this was with the cadmium-treated group which showed a strong cell proliferation inhibition. This study provides the fundamental data for the understanding of simultaneous heavy metal exposure tendency at the time of particulate matter exposure in subway stations and the identification of heavy metal sources. Moreover, this study can be used as the fundamental data for the cell toxicity study of the subway-oriented heavy metal-containing particulate matter. PMID:24278519

[Influence of decomposition of Cladophora sp. on phosphorus concentrations and forms in the overlying water].

PubMed

Hou, Jin-Zhi; Wei, Quan; Gao, Li; Sun, Wei-Ming

2013-06-01

Sediments were sampled in the dominated zone of Cladophora sp. in Rongcheng Swan Lake, and cultivated with algae in the laboratory to reveal the influence of Cladophora decomposition on concentrations and forms of phosphorus in the overlying water. Concentrations of total phosphorus (TP), dissolved total phosphorus (DTP), soluble reactive phosphorus (SRP), particulate phosphorus (PP) and dissolved organic phosphorus (DOP) in overlying water were investigated, and some physicochemical parameters, such as dissolved oxygen (DO), pH and conductivity were monitored during the experiment. In addition, the influence of algae decomposition on P release from sediments was analyzed. Due to the decomposition of Cladophora, DO concentration in the overlying water declined remarkably and reached the anoxic condition (0-0.17 mg x L(-1)). The pH value of different treatments also decreased, and treatments with algae reduced by about 1 unit. Concentrations of TP and different P forms all increased obviously, and the increasing extent was larger with the adding algae amount. TP concentrations of different treatments varied from 0.04 mg x L(-1) to 1.34 mg x L(-1). DOP and PP were the main P forms in the overlying water in algae without sediments treatments, but SRP concentrations became much higher in algae with sediments treatments. The result showed that P forms released from decomposing Cladophora were mainly DOP and PP, and the Cladophora decomposition could also promote the sediments to release P into the overlying water.

In vivo and in vitro proinflammatory effects of particulate air pollution (PM10).

PubMed Central

Li, X Y; Gilmour, P S; Donaldson, K; MacNee, W

1997-01-01

Epidemiologic studies have reported associations between fine particulate air pollution, especially particles less than 10 mm in diameter (PM10), and the development of exacerbations of asthma and chronic obstructive pulmonary disease. However, the mechanism is unknown. We tested our hypothesis that PM10 induces oxidant stress, causing inflammation and injury to airway epithelium. We assessed the effects of intratracheal instillation of PM10 in rat lungs. The influx of inflammatory cells was measured in bronchoalveolar lavage (BAL). Airspace epithelial permeability was assessed as total protein in bronchoalveolar lavage fluid (BALF) in vivo. The oxidant properties of PM10 were determined by their ability to cause changes in reduced glutathione (GSH) and oxidized glutathione (GSSG). We also compared the effects of PM10 with those of fine (CB) and ultrafine (ufCB) carbon black particles. Six hours after intratracheal instillation of PM10, we noted an influx of neutrophils (up to 15% of total BAL cells) in the alveolar space, increased epithelial permeability, an increase in total protein in BALF from 0.39 +/- 0.01 to 0.62 +/- 0.01 mg/ml (mean +/- SEM) and increased lactate dehydrogenase concentrations in BALF. An even greater inflammatory response was observed after intratracheal instillation of ufCB, but not after CB instillation. PM10 had oxidant activity in vivo, as shown by decreased GSH in BALF (from 0.36 +/- 0.05 to 0.25 +/- 0.01 nmol/ml) after instillation. BAL leukocytes from rats treated with PM10 produced greater amounts of nitric oxide, measured as nitrite (control 3.07 +/- 0.33, treated 4.45 +/- 0.23 mM/1 x 10(6) cells) and tumor necrosis factor alpha (control 21.0 +/- 3.1, treated 179.2 +/- 29.4 unit/1 x 10(6) cells) in culture than BAL leukocytes obtained from control animals. These studies provide evidence that PM10 has free radical activity and causes lung inflammation and epithelial injury. These data support our hypothesis concerning the mechanism for the adverse effects of particulate air pollution on patients with airway diseases. PMID:9400738

A Literature Review of Concentrations and Size Distributions of Ambient Airborne Pb-Containing Particulate Matter

EPA Science Inventory

The final 2008 lead (Pb) national ambient air quality standards (NAAQS) revision maintains Pb in total suspended particulate matter as the indicator. However, the final rule permits the use of low-volume PM₁₀ (particulate matter sampled with a 50% cut-point of 10 μm) F...

ACUTE CHANGES IN SPUTUM COLLECTED FROM EXPOSED HUMAN SUBJECTS IN MINING CONDITIONS

PubMed Central

Wong, Simon S.; Sun, Nina N.; Miller, Hugh B.; Witten, Mark L.; Burgess, Jefferey L.

2015-01-01

Neprilysin (NEP) is a key cell surface peptidase in the maintenance of airway homeostasis and the development of pulmonary disorders. However, little information is available about the effect of particulate matter (PM) on airway NEP. In this controlled human exposure study, changes in induced sputum were measured in eleven subjects at baseline, overshot (OS) mucking, and diesel exhaust (DE) exposure days. Neither OS condition nor DE exposure was found to induce significant changes in total protein, but DE induced significant increases in cell numbers of macrophages and epithelium. Moreover, significant increases in soluble NEP were observed following OS mining dust particulates (0.43 ± 0.06, p = 0.023) and DE exposure (0.30 ± 0.04, p = 0.035) when compared with the baseline control (0.40 ± 0.03), with 42% and 31% average net increase, respectively. Pearson’s correlation analyses indicated that sputum NEP activity were significantly associated with personal exposure product [Elemental carbon concentration, mg/m3 X time, min. (C X T)]. Data suggest that the changes in NEP activity may be an early, accurate endpoint for airway epithelial injury and provided a new insight into the mechanism of the airway effects in these exposure conditions. PMID:20384431

Analysis of Androgenic Steroids in Environmental Waters by Large-volume Injection Liquid Chromatography Tandem Mass Spectrometry

PubMed Central

Backe, Will J.; Ort, Christoph; Brewer, Alex J.; Field, Jennifer A.

2014-01-01

A new method was developed for the analysis of natural and synthetic androgenic steroids and their selected metabolites in aquatic environmental matrices using direct large-volume injection (LVI) high performance liquid chromatography (HPLC) tandem mass spectrometry (MS/MS). Method accuracy ranged from 88 to 108% for analytes with well-matched internal standards. Precision, quantified by relative standard deviation (RSD), was less than 12%. Detection limits for the method ranged from 1.2 to 360 ng/L. The method was demonstrated on a series of 1-hr composite wastewater influent samples collected over a day with the purpose of assessing temporal profiles of androgen loads in wastewater. Testosterone, androstenedione, boldenone, and nandrolone were detected in the sample series at concentrations up to 290 ng/L and loads up to 535 mg. Boldenone, a synthetic androgen, had a temporal profile that was strongly correlated to testosterone, a natural human androgen, suggesting its source may be endogenous. An analysis of the sample particulate fraction revealed detectable amounts of sorbed testosterone and androstenedione. Androstenedione sorbed to the particulate fraction accounted for an estimated five to seven percent of the total androstenedione mass. PMID:21391574

Analysis of androgenic steroids in environmental waters by large-volume injection liquid chromatography tandem mass spectrometry.

PubMed

Backe, Will J; Ort, Christoph; Brewer, Alex J; Field, Jennifer A

2011-04-01

A new method was developed for the analysis of natural and synthetic androgenic steroids and their selected metabolites in aquatic environmental matrixes using direct large-volume injection (LVI) high-performance liquid chromatography (HPLC) tandem mass spectrometry (MS/MS). Method accuracy ranged from 87.6 to 108% for analytes with well-matched internal standards. Precision, quantified by relative standard deviation (RSD), was less than 12%. Detection limits for the method ranged from 1.2 to 360 ng/L. The method was demonstrated on a series of 1 h composite wastewater influent samples collected over a day with the purpose of assessing temporal profiles of androgen loads in wastewater. Testosterone, androstenedione, boldenone, and nandrolone were detected in the sample series at concentrations up to 290 ng/L and loads up to 535 mg/h. Boldenone, a synthetic androgen, had a temporal profile that was strongly correlated to testosterone, a natural human androgen, suggesting its source may be endogenous. An analysis of the sample particulate fraction revealed detectable amounts of sorbed testosterone and androstenedione. Androstenedione sorbed to the particulate fraction accounted for an estimated 5 to 7% of the total androstenedione mass.

Urban air-quality assessment and source apportionment studies for Bhubaneshwar, Odisha

NASA Astrophysics Data System (ADS)

Mahapatra, Parth Sarathi; Ray, Sanak; Das, Namrata; Mohanty, Ayusman; Ramulu, T. S.; Das, Trupti; Chaudhury, G. Roy; Das, S. N.

2013-04-01

Acid- and water-soluble component of suspended particulate matter was studied from January 2009 to December 2009 at Bhubaneshwar, an urban coastal location of eastern India, by high-volume sampler, environmental dust monitor using GRIMM®, and scanning electron microscope and energy dispersive X-ray spectrometer. The water-soluble components accounted for 30-45 % of the total suspended particulate matter, and the major elements were observed to be ammonium and nitrate as the cationic and anionic species, respectively. The acid-soluble component like copper, nickel, cobalt, iron, and lead accounted for 5-15 % of the total particulate matter concentration. The composition of particulate matter shows a clear seasonal variation in relation to wind speed, wind direction, and trajectories of the air mass movement. The GRIMM spectrometer analysis shows higher concentration of fine particulate matter. Source apportionment and enrichment factor analysis indicated that except sodium and chloride, all other elements have emerged from different sources such as crustal as well as anthropogenic.

Characterizing dry deposition of mercury in urban runoff

USGS Publications Warehouse

Fulkerson, M.; Nnadi, F.N.; Chasar, L.S.

2007-01-01

Stormwater runoff from urban surfaces often contains elevated levels of toxic metals. When discharged directly into water bodies, these pollutants degrade water quality and impact aquatic life and human health. In this study, the composition of impervious surface runoff and associated rainfall was investigated for several storm events at an urban site in Orlando, Florida. Total mercury in runoff consisted of 58% particulate and 42% filtered forms. Concentration comparisons at the start and end of runoff events indicate that about 85% of particulate total mercury and 93% of particulate methylmercury were removed from the surface before runoff ended. Filtered mercury concentrations showed less than 50% reduction of both total and methylmercury from first flush to final flush. Direct comparison between rainfall and runoff at this urban site indicates dry deposition accounted for 22% of total inorganic mercury in runoff. ?? 2007 Springer Science+Business Media B.V.

Application of particle size distributions to total particulate stack samples to estimate PM2.5 and PM10 emission factors for agricultural sources

USDA-ARS?s Scientific Manuscript database

Particle size distributions (PSD) have long been used to more accurately estimate the PM10 fraction of total particulate matter (PM) stack samples taken from agricultural sources. These PSD analyses were typically conducted using a Coulter Counter with 50 micrometer aperture tube. With recent increa...

Particulate organic matter in rivers of Fukushima: An unexpected carrier phase for radiocesiums.

PubMed

Naulier, Maud; Eyrolle-Boyer, Frédérique; Boyer, Patrick; Métivier, Jean-Michel; Onda, Yuichi

2017-02-01

The role of particulate organic matter in radiocesium transfers from soils to rivers was investigated in areas contaminated by the Fukushima Daiichi Nuclear Power Plant accident. Suspended and deposited sediments, filtered water, macro organic debris and dead leaves were sampled along the six most contaminated coastal river catchments of the Fukushima prefecture in the early autumns 2013 and 2014. Radiocesium concentrations of river samples and total organic carbon concentrations in suspended and deposited sediments were measured. Radiocesium concentrations of suspended and deposited sediments were significantly correlated to 137 Cs inventories in soils and total organic carbon. The distributions of radiocesium between the organic and mineral phases of both types of sediment were assessed by using a modelling approach. The results suggest that, during the early autumn season, the organic fraction was the main phase that carried the radiocesiums in deposited sediments and in suspended sediments for suspended loads <25mg·L -1 . For higher suspended loads like those occurring during typhoon periods, the mineral fraction was the main carrier phase. Thus, high apparent distribution coefficient values noted by various authors in Fukushima could be attributed to the high radiocesium contents of particulate organic matter. Since it is well known that organic compounds generally do not significantly adsorb radiocesium onto specific sites, several hypotheses are suggested: 1) Radiocesiums may have been absorbed into organic components at the early stage of atmospheric radioactive deposits and/or later due to biomass recycling and 2) Those elements would be partly carried by glassy hot particles together with organic matter transported by rivers in Fukushima. Both hypotheses would lead to conserve the amount of radiocesiums associated with particles during their transfers from the contaminated areas to the marine environment. Finally, such organically bound radiocesium would lead to significant deliveries of bioavailable radiocesium for living organisms at Fukushima. Copyright © 2016 Elsevier B.V. All rights reserved.

Countercurrent flow of supercritical anti-solvent in the production of pure xanthophylls from Nannochloropsis oculata.

PubMed

Cho, Yueh-Cheng; Wang, Yuan-Chuen; Shieh, Chwen-Jen; Lin, Justin Chun-Te; Chang, Chieh-Ming J; Han, Esther

2012-08-10

This study examined pilot scaled elution chromatography coupled with supercritical anti-solvent precipitation (using countercurrent flow) in generating zeaxanthin-rich particulates from a micro-algal species. Ultrasonic agitated acetone extract subjected to column fractionation successfully yielded a fraction containing 349.4 mg/g of zeaxanthin with a recovery of 85%. Subsequently, supercritical anti-solvent (SAS) precipitation of the column fraction at 150 bar and 343 K produced submicron-sized particulates with a concentration of 845.5mg/g of zeaxanthin with a recovery of 90%. Experimental results from a two-factor response surface method SAS precipitation indicated that purity, mean size and morphology of the precipitates were significantly affected by the flow type configuration, feed flow rate and injection time. Copyright © 2012 Elsevier B.V. All rights reserved.

Particle size and morphology of UHMWPE wear debris in failed total knee arthroplasties--a comparison between mobile bearing and fixed bearing knees.

PubMed

Huang, Chun-Hsiung; Ho, Fang-Yuan; Ma, Hon-Ming; Yang, Chan-Tsung; Liau, Jiann-Jong; Kao, Hung-Chan; Young, Tai-Horng; Cheng, Cheng-Kung

2002-09-01

Osteolysis induced by ultrahigh molecular weight polyethylene wear debris has been recognized as the major cause of long-term failure in total joint arthroplasties. In a previous study, the prevalence of intraoperatively identified osteolysis during primary revision surgery was much higher in mobile bearing knee replacements (47%) than in fixed bearing knee replacements (13%). We postulated that mobile bearing knee implants tend to produce smaller sized particles. In our current study, we compared the particle size and morphology of polyethylene wear debris between failed mobile bearing and fixed bearing knees. Tissue specimens from interfacial and lytic regions were extracted during revision surgery of 10 mobile bearing knees (all of the low contact stress (LCS) design) and 17 fixed bearing knees (10 of the porous-coated anatomic (PCA) and 7 of the Miller/Galante design). Polyethylene particles were isolated from the tissue specimens and examined using both scanning electron microscopy and light-scattering analyses. The LCS mobile bearing knees produced smaller particulate debris (mean equivalent spherical diameter: 0.58 microm in LCS, 1.17 microm in PCA and 5.23 microm in M/G) and more granular debris (mean value: 93% in LCS, 77% in PCA and 15% in M/G).

Determination of exposure to respirable quartz in the stone crushing units at Azendarian-West of Iran.

PubMed

Bahrami, Abdul Rahman; Golbabai, Faridah; Mahjub, Hossien; Qorbani, Farshid; Aliabadi, Mohsan; Barqi, Mohamadali

2008-08-01

The purpose of this study is to describe the personal exposure to respirable dust and quartz and in stone crushing units located at west of Iran. A size of 40 personal samples and 40 stationary samples were obtained and analysis was done by X-ray diffraction (XRD). The results of personal sampling were shown the concentrations of respirable dust exposure level in workers of process, hopper and drivers were 1.90, 2.22, 1.41 times greater than Occupational Safety and Health Administration permissible exposure limit (OSHA PEL). The average value of total dust and respirable dust emission from stationary sources was 9.46 mg/m(3), 1.24 mg/m(3) respectively, showing that 13.8 % of total dust is respirable. The efficiency of local exhaust ventilation (LEV) to control of particles inside of industrial units was greater than 99%. It is concluded from this research the particulate generated from stone crushing activities contain a significant amount of respirable particle. The amount of free silica in stone quartz is 85 to 97 percent that emission of particles effect to health workers. LEV has important effect in the removal of silica particles in stone crushing units. The worker of hoppers still exposed to silica more than standard limits.

Efficient bioremediation of total organic carbon (TOC) in integrated aquaculture system by marine sponge Hymeniacidon perleve.

PubMed

Fu, Wantao; Wu, Yichun; Sun, Liming; Zhang, Wei

2007-08-15

The aim of this study is to investigate the potential of using marine sponge Hymeniacidon perleve to remove total organic carbon (TOC) in integrated aquaculture ecosystems. In sterilized natural seawater (SNSW) with different concentrations of TOC, H. perleve removed approximately 44-61% TOC during 24 h, with retention rates of ca. 0.19-1.06 mg/h .g-fresh sponge, however no particulate selectivity was observed. The highest initial TOC concentration, in which about 2.7 g fresh sponges could remove TOC effectively in 0.5-L SNSW, is 214.3-256.9 mg/L. The highest capacity of TOC removal and clearance rate (CR) by H. perleve is ca. 25.50 mg-TOC/g-fresh sponge and 7.64 mL/h . g-fresh sponge within 24 h, respectively. Until reaching the highest TOC removal capacity, the TOC removal capacity and clearance rate of H. perleve increased with initial TOC concentration, and dropped dramatically thereafter. After reaching the highest removal capacity, H. perleve could only remove relatively lower TOC concentration in seawater in subsequent run. The TOC removal kinetics in SNSW by H. perleve fitted very well with a S-shaped curve and a Logistic model equation (R(2) = 0.999). In different volumes of SNSW with a fixed initial TOC concentration, the weight/volume ratio of sponge biomass and SFNSW was optimized at 1.46 g-fresh sponge/1-L SNSW to achieve the maximum TOC removal. When co-cultured with marine fish Fugu rubripes for 15 days, H. perleve removed TOC excreted by F. rubripes with similar retention rates of ca. 0.15 mg/h . g-fresh sponge, and the sponge biomass increased by 22.8%. (c) 2007 Wiley Periodicals, Inc.

Physicochemical characterization of fine particles from small-scale wood combustion

NASA Astrophysics Data System (ADS)

Lamberg, Heikki; Nuutinen, Kati; Tissari, Jarkko; Ruusunen, Jarno; Yli-Pirilä, Pasi; Sippula, Olli; Tapanainen, Maija; Jalava, Pasi; Makkonen, Ulla; Teinilä, Kimmo; Saarnio, Karri; Hillamo, Risto; Hirvonen, Maija-Riitta; Jokiniemi, Jorma

2011-12-01

Emissions from small-scale wood combustion appliances are of special interest since fine particles have been consistently associated with adverse health effects. It has been reported that the physicochemical characteristics of the emitted particles affect also their toxic properties but the mechanisms behind these phenomena and the causative role of particles from wood combustion sources are still mostly unknown. Combustion situations vary significantly in small-scale appliances, especially in batch combustion. Combustion behaviour is affected by fuel properties, appliance type and operational practice. Particle samples were collected from six appliances representing different combustion situations in small-scale combustion. These appliances were five wood log fuelled stoves, including one stove equipped with modern combustion technology, three different conventional combustion appliances and one sauna stove. In addition, a modern small-scale pellet boiler represented advanced continuous combustion technology. The aim of the study was to analyze gas composition and fine particle properties over different combustion situations. Fine particle (PM 1) emissions and their chemical constituents emerging from different combustion situations were compared and this physicochemical data was combined with the toxicological data on cellular responses induced by the same particles (see Tapanainen et al., 2011). There were significant differences in the particle emissions from different combustion situations. Overall, the efficient combustion in the pellet boiler produced the smallest emissions whereas inefficient batch combustion in a sauna stove created the largest emissions. Improved batch combustion with air-staging produced about 2.5-fold PM 1 emissions compared to the modern pellet boiler (50.7 mg MJ -1 and 19.7 mg MJ -1, respectively), but the difference in the total particulate PAH content was 750-fold (90 μg MJ -1 and 0.12 μg MJ -1, respectively). Improved batch combustion and conventional batch combustion showed almost the same PM 1 emissions (51.6 mg MJ -1), but a 10-fold difference in total particulate PAH emissions (910 μg MJ -1). These results highlight that same PM 1 emissions can be associated with very different chemical compositions, potentially leading to different toxic properties of the particles. Thus, changing from an old, less efficient, combustion appliance to a modern appliance can have a greater impact on toxic properties than the emitted PM 1 mass might indicate.

Reductions in Emissions of Carbonaceous Particulate Matter and Polycyclic Aromatic Hydrocarbons from Combustion of Biomass Pellets in Comparisonwith Raw Fuel Burning

PubMed Central

SHEN, Guofeng; TAO, Shu; WEI, Siye; ZHANG, Yanyan; WANG, Rong; WANG, Bin; LI, Wei; SHEN, Huizhong; HUANG, Ye; CHEN, Yuanchen; CHEN, Han; YANG, Yifeng; WANG, Wei; WEI, Wen; WANG, Xilong; LIU, Wenxing; WANG, Xuejun; SIMONICH, Staci L. Massey

2012-01-01

Biomass pellets are emerging as a cleaner alternative to traditional biomass fuels. The potential benefits of using biomass pellets include improving energy utilization efficiency and reducing emissions of air pollutants. To assess the environmental, climate, and health significance of replacing traditional fuels with biomass pellets, it is critical to measure the emission factors (EFs) of various pollutants from pellet burning. However, only a few field measurements have been conducted on the emissions of carbon monoxide (CO), particulate matter (PM), and polycyclic aromatic hydrocarbons (PAHs) from the combustion of pellets. In this study, pine wood and corn straw pellets were burned in a pellet burner (2.6 kW) and the EFs of CO, organic carbon, elemental carbon, PM, and PAHs (EFCO, EFOC, EFEC, EFPM, and EFPAH) were determined. The average EFCO, EFOC, EFEC, and EFPM were 1520±1170, 8.68±11.4, 11.2±8.7, and 188±87 mg/MJ for corn straw pellets, and 266±137, 5.74±7.17, 2.02±1.57, and 71.0±54.0 mg/MJ for pine wood pellets, respectively. Total carbonaceous carbon constituted 8 to 14% of the PM mass emitted. The measured values of EFPAH for the two pellets were 1.02±0.64 and 0.506±0.360 mg/MJ, respectively. The secondary side air supply in the pellet burner did not change the EFs of most pollutants significantly (p > 0.05). The only exceptions were EFOC and EFPM for pine wood pellets because of reduced combustion temperatures with the increased air supply. In comparison with EFs for the raw pine wood and corn straw, EFCO, EFOC, EFEC, and EFPM for pellets were significantly lower than those for raw fuels (p < 0.05). However, the differences in EFPAH were not significant (p > 0.05). Based on the measured EFs and thermal efficiencies, it was estimated that 95, 98, 98, 88, and 71% reductions in the total emissions of CO, OC, EC, PM, and PAHs could be achieved by replacing the raw biomass fuels combusted in traditional cooking stoves with pellets burned in modern pellet burners. PMID:22568759

Reductions in emissions of carbonaceous particulate matter and polycyclic aromatic hydrocarbons from combustion of biomass pellets in comparison with raw fuel burning.

PubMed

Shen, Guofeng; Tao, Shu; Wei, Siye; Zhang, Yanyan; Wang, Rong; Wang, Bin; Li, Wei; Shen, Huizhong; Huang, Ye; Chen, Yuanchen; Chen, Han; Yang, Yifeng; Wang, Wei; Wei, Wen; Wang, Xilong; Liu, Wenxing; Wang, Xuejun; Masse Simonich, Staci L y

2012-06-05

Biomass pellets are emerging as a cleaner alternative to traditional biomass fuels. The potential benefits of using biomass pellets include improving energy utilization efficiency and reducing emissions of air pollutants. To assess the environmental, climate, and health significance of replacing traditional fuels with biomass pellets, it is critical to measure the emission factors (EFs) of various pollutants from pellet burning. However, only a few field measurements have been conducted on the emissions of carbon monoxide (CO), particulate matter (PM), and polycyclic aromatic hydrocarbons (PAHs) from the combustion of pellets. In this study, pine wood and corn straw pellets were burned in a pellet burner (2.6 kW), and the EFs of CO, organic carbon, elemental carbon, PM, and PAHs (EF(CO), EF(OC), EF(EC), EF(PM), and EF(PAH)) were determined. The average EF(CO), EF(OC), EF(EC), and EF(PM) were 1520 ± 1170, 8.68 ± 11.4, 11.2 ± 8.7, and 188 ± 87 mg/MJ for corn straw pellets and 266 ± 137, 5.74 ± 7.17, 2.02 ± 1.57, and 71.0 ± 54.0 mg/MJ for pine wood pellets, respectively. Total carbonaceous carbon constituted 8 to 14% of the PM mass emitted. The measured values of EF(PAH) for the two pellets were 1.02 ± 0.64 and 0.506 ± 0.360 mg/MJ, respectively. The secondary side air supply in the pellet burner did not change the EFs of most pollutants significantly (p > 0.05). The only exceptions were EF(OC) and EF(PM) for pine wood pellets because of reduced combustion temperatures with the increased air supply. In comparison with EFs for the raw pine wood and corn straw, EF(CO), EF(OC), EF(EC), and EF(PM) for pellets were significantly lower than those for raw fuels (p < 0.05). However, the differences in EF(PAH) were not significant (p > 0.05). Based on the measured EFs and thermal efficiencies, it was estimated that 95, 98, 98, 88, and 71% reductions in the total emissions of CO, OC, EC, PM, and PAHs could be achieved by replacing the raw biomass fuels combusted in traditional cooking stoves with pellets burned in modern pellet burners.

A health-based assessment of particulate air pollution in urban areas of Beijing in 2000-2004.

PubMed

Zhang, Minsi; Song, Yu; Cai, Xuhui

2007-04-15

Particulate air pollution is a serious problem in Beijing. The annual concentration of particulate matter with aerodynamic diameter less than 10 microm (PM(10)), ranging from 141 to 166 microg m(-3) in 2000-2004, could be very harmful to human health. In this paper, we presented the mortality and morbidity effects of PM(10) pollution based on statistical data and the epidemiological exposure-response function. The economic costs to health during the 5 years were estimated to lie between US$1670 and $3655 million annually, accounting for about 6.55% of Beijing's gross domestic product each year. The total costs were apportioned into two parts caused by: the local emissions and long-range transported pollution. The contribution from local emissions dominated the total costs, accounting on average for 3.60% of GDP. However, the contributions from transported pollution cannot be neglected, and the relative percentage to the total costs from the other regions could account for about 45%. An energy policy and effective measures should be proposed to reduce particulate matter, especially PM(2.5) pollution in Beijing to protect public health. The Beijing government also needs to cooperate with the other local governments to reduce high background level of particulate air pollution.

Assessing dust exposure in an integrated iron and steel manufacturing plant in South India.

PubMed

Ravichandran, B; Krishnamurthy, V; Ravibabu, K; Raghavan, S; Rajan, B K; Rajmohan, H R

2008-01-01

A study to monitor and estimate respirable particulate matter (RPM), toxic trace metal concentrations in the work environment was carried out in different sections of an integrated steel manufacturing industry. The average RPM concentration observed varied according to the section blast furnace was 2.41 mg/m;{3}; energy optimization furnace, 1.87 mg/m;{3}; sintering plant, 0.98 mg/m;{3}; continuous casting machine, 1.93 mg/m;{3}. The average trace metal concentration estimated from the RPM samples like iron, manganese, lead and chromium did not exceed ACGIH prescribed levels.

Nitrogen and phosphorus removed from a subsurface flow multi-stage filtration system purifying agricultural runoff.

PubMed

Zhao, Yaqi; Huang, Lei; Chen, Yucheng

2018-07-01

Agricultural nonpoint source pollution has been increasingly serious in China since the 1990s. The main causes were excessive inputs of nitrogen fertilizer and pesticides. A multi-stage filtration system was built to test the purification efficiencies and removal characteristics of nitrogen and phosphorus when treating agricultural runoff. Simulated runoff pollution was prepared by using river water as source water based on the monitoring of local agricultural runoff. Experimental study had been performed from September to November 2013, adopting 12 h for flooding and 12 h for drying. The results showed that the system was made adaptive to variation of inflow quality and quantity, and had good removal for dissolved total nitrogen, total nitrogen, dissolved total phosphorus (DTP), and total phosphorus, and the average removal rate was 27%, 36%, 32%, and 48%, respectively. Except nitrate ([Formula: see text]), other forms of nitrogen and phosphorus all decreased with the increase of stages. Nitrogen was removed mainly in particle form the first stage, and mostly removed in dissolved form the second and third stage. Phosphorus was removed mainly in particulate during the first two stages, but the removal of particulate phosphorus and DTP were almost the same in the last stage. An approximate logarithmic relationship between removal loading and influent loading to nitrogen and phosphorus was noted in the experimental system, and the correlation coefficient was 0.78-0.94. [Formula: see text]: ammonium; [Formula: see text]: nitrite; [Formula: see text]: nitrate; DTN: dissolved total nitrogen; TN: total nitrogen; DTP: dissolved total phosphorus; TP: total phosphorus; PN: particulate nitrogen; PP: particulate phosphorus.

Emissions of particulate-bound elements from stationary diesel engine: Characterization and risk assessment

NASA Astrophysics Data System (ADS)

Betha, Raghu; Balasubramanian, Rajasekhar

2011-09-01

There has been an increasing concern about the emissions of airborne particulate matter (PM) from diesel engines because of their close association with adverse health and environmental impacts. Among the alternative fuels being considered, biodiesel made by the transesterification of waste cooking oil has received wide attention in recent years because of its low cost and the added advantage of reducing waste oil disposal. This study was conducted to make a comparative evaluation of the particulate-bound elements emitted from ultra low sulphur diesel (ULSD) and waste cooking oil-derived biodiesel (B100) and a blend of both the fuels (B50). It was observed that the PM mass concentrations were reduced by about 36% when B100 was used. Crustal elements such as Mg, K and Al were found to be in higher concentrations compared to other elements emitted from both B100 and ULSD. Zn, Cr, Cu, Fe, Ni, Mg, Ba, K were found to be higher in the biodiesel exhaust while Co, Pb, Mn, Cd, Sr, and As were found to be higher in the ULSD exhaust. To evaluate the potential health risk due to inhalation of PM emitted from diesel engines running on ULSD and B100, health risk estimates based on exposure and dose-response assessments of particulate-bound elements were calculated assuming exposure for 24 h. The findings indicate that the exposure to PM of the B100 exhaust is relatively more hazardous and may pose adverse health effects compared to ULSD.

Effects of dietary particulate limestone, vitamin K3 and fluoride and photostimulation on skeletal morphology and osteoporosis in laying hens.

PubMed

Fleming, R H; McCormack, H A; McTeir, L; Whitehead, C C

2003-12-01

1. Female chicks of a White Leghorn strain were fed three different diets from one day old: control, additional vitamin K3 (10 mg/kg), and a diet containing a combination of additional vitamin K3, sodium fluoride (10 mg/kg) and limestone in particulate rather than powdered form. At 16 weeks photoperiod was increased for half the birds from 8:16 L:D to 16:8 L:D immediately or by one hour per week to the same ultimate photoperiod for the other half. 2. Age at first egg was lower by 4.0 d for birds on the fast lighting regime but there were no overall effects of lighting on bone quality at either 25 or 70 weeks. 3. Additional vitamin K3 resulted in higher proximal tarsometatarsus cancellous bone volumes at 15 weeks and throughout the laying period compared with controls. Plasma osteocalcin concentrations were unaffected by vitamin K3 supplementation during growth. 4. The combination diet resulted in beneficial responses of 12 to 20% in most bone characteristics in hens at 70 weeks. The magnitude of these effects was similar to a previous study involving a particulate calcium source alone (Fleming et al., Poultry Science, 39: 434-440, 1998b). We conclude that the beneficial effects of the combined treatment over the lifetime of the hens were attributable mainly to the presence in the diet of a calcium source in particulate form.

Effectiveness of Radiation Synovectomy with Samarium-153 Particulate Hydroxyapatite in Rheumatoid Arthritis Patients with Knee Synovitis: A Controlled Randomized Double-Blind Trial

PubMed Central

dos Santos, Marla Francisca; Furtado, Rita Nely Vilar; Konai, Monique Sayuri; Castiglioni, Mario Luiz Vieira; Marchetti, Renata Rosa; Natour, Jamil

2009-01-01

OBJECTIVES: The aim of the present study was to investigate the effectiveness of Samarium153-particulate hydroxyapatite radiation synovectomy in rheumatoid arthritis patients with chronic knee synovitis. METHODS: Fifty-eight rheumatoid arthritis patients (60 knees) with chronic knee synovitis participated in a controlled double-blinded trial. Patients were randomized to receive either an intra-articular injection with 40 mg triamcinolone hexacetonide alone (TH group) or 40 mg triamcinolone hexacetonide combined with 15 mCi Samarium153-particulate hydroxyapatite (Sm/TH group). Blinded examination at baseline (T0) and at 1 (T1), 4 (T4), 12 (T12), 32 (T32), and 48 (T48) weeks post-intervention were performed on all patients and included a visual analog scale for joint pain and swelling as well as data on morning stiffness, flexion, extension, knee circumference, Likert scale of improvement, percentage of improvement, SF-36 generic quality of life questionnaire, Stanford Health Assessment Questionnaire (HAQ), Lequesne index, use of non-steroidal anti-inflammatory drugs or oral corticosteroids, events and adverse effects, calls to the physician, and hospital visits. RESULTS: The sample was homogeneous at baseline, and there were no withdrawals. Improvement was observed in both groups in relation to T0, but no statistically significant differences between groups were observed regarding all variables at the time points studied. The Sm/TH group exhibited more adverse effects at T1 (p<0.05), but these were mild and transitory. No severe adverse effects were reported during follow-up. CONCLUSION: Intra-articular injection of Samarium153-particulate hydroxyapatite (15 mCi) with 40 mg of triamcinolone hexacetonide is not superior to triamcinolone hexacetonide alone for the treatment of knee synovitis in patients with rheumatoid arthritis at 1 y of follow-up. PMID:20037706

Indoor air quality during renovation actions: a case study.

PubMed

Abdel Hameed, A A; Yasser, I H; Khoder, I M

2004-09-01

A temporary renovation activity releases considerably high concentrations of particulate matter, viable and non-viable, into air. These pollutants are a potential contributor to unacceptable indoor air quality (IAQ). Particulate matter and its constituents lead, sulfate, nitrate, chloride, ammonium and fungi as well as fungal spores in air were evaluated in a building during renovation action. Suspended dust was recorded at a mean value of 6.1 mg m(-3) which exceeded the Egyptian limit values for indoor air (0.15 mg m(-3)) and occupational environments (5 mg m(-3)). The highest particle frequency (23%) of aerodynamic diameter (dae) was 1.7 microm. Particulate sulfate (SO(4)(2-)), nitrate (NO(3)(-)), chloride (Cl(-)), ammonium (NH(4)(+)) and lead components of suspended dust averaged 2960, 28, 1350, 100 and 13.3 microg m(-3), respectively. Viable fungi associated with suspended dust and that in air averaged 1.11 x 10(6) colony forming unit per gram (cfu g(-1)) and 92 colony forming unit per plate per hour (cfu p(-1) h(-1)), respectively. Cladosporium(33%), Aspergillus(25.6%), Alternaria(11.2%) and Penicillium(6.6%) were the most frequent fungal genera in air, whereas Aspergillus(56.8%), Penicillium(10.3%) and Eurotium(10.3%) were the most common fungal genera associated with suspended dust. The detection of Aureobasidium, Epicoccum, Exophiala, Paecilomyces, Scopulariopsis, Ulocladium and Trichoderma is an indication of moisture-damaged building materials. Alternaria, Aureobasidium, Cladosporium, Scopulariopsis and Nigrospora have dae > 5 microm whereas Aspergillus, Penicillium and Verticillium have dae < 5 microm which are suited to penetrate deeply into lungs. Particulate matter from the working area infiltrates the occupied zones if precautionary measures are inadequate. This may cause deterioration of IAQ, discomfort and acute health problems. Renovation should be carefully designed and managed, in order to minimize degradation of the indoor and outdoor air quality.

Sinking fluxes of 210Pb and 210Po in the deep basin of the northern South China Sea.

PubMed

Wei, Ching-Ling; Chia, Chao-Yuan; Chou, Wen-Chen; Lee, Wen-Huei

2017-08-01

Vertical fluxes of total mass (F mass ), particulate organic carbon (F POC ), particulate inorganic carbon (F PIC ), 210 Pb (F Pb-210 ), and 210 Po (F Po-210 ) were determined by sediment traps deployed at two depths, 2000 m and 3500 m, at SEATS (South East Asian Time-series Study, 116°00°E, 18°00°N) in the northern South China Sea during June 2008-June 2009. The F mass ranges from 12.2 to 55.1 mg m -2  d -1 and from 89.3 to 250.8 mg m -2  d -1 , at 2000 m and 3500 m, respectively, and shows seasonal and inter-annul variation. The temporal variation of F POC , F PIC , and F Pb-210 were in phase with the F mass , which was coupled with the seasonal cycles of primary production in the euphotic layer. The F Pb-210 ranges from 5 to 48 dpm m -2 d -1 and from 38 to 105 dpm m -2 d -1 , at 2000 m and 3500 m, respectively. Contrasting with 210 Pb, the F Po-210 shows poor correlation with F mass . The F Po-210 ranges from 3 to 146 dpm m -2 d -1 and from 50 to 309 dpm m -2 d -1 , at 2000 m and 3500 m, respectively. Episodic events of the settling of biological particles from the surface layer and the regeneration processes the deep layer control the 210 Po removal in the water column of the South China Sea. Strong correlations of the flux and source ratio of 210 Pb, (F/P) Pb-210 , and the particulate carbon fluxes were found, which give relationships of F POC (μg cm -2 y -1 ) = 26.8 + 371.0 (F/P) Pb-210 and F PIC (μg cm -2 y -1 ) = -1.4 + 533.1 (F/P) Pb-210 . Copyright © 2016 Elsevier Ltd. All rights reserved.

Aqueous biphasic extraction of uranium and thorium from contaminated soils. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chaiko, D.J.; Gartelmann, J.; Henriksen, J.L.

1995-07-01

The aqueous biphasic extraction (ABE) process for soil decontamination involves the selective partitioning of solutes and fine particulates between two immiscible aqueous phases. The biphase system is generated by the appropriate combination of a water-soluble polymer (e.g., polyethlene glycol) with an inorganic salt (e.g., sodium carbonate). Selective partitioning results in 99 to 99.5% of the soil being recovered in the cleaned-soil fraction, while only 0.5 to 1% is recovered in the contaminant concentrate. The ABE process is best suited to the recovery of ultrafine, refractory material from the silt and clay fractions of soils. During continuous countercurrent extraction tests withmore » soil samples from the Fernald Environmental Management Project site (Fernald, OH), particulate thorium was extracted and concentrated between 6- and 16-fold, while the uranium concentration was reduced from about 500 mg/kg to about 77 mg/kg. Carbonate leaching alone was able to reduce the uranium concentration only to 146 mg/kg. Preliminary estimates for treatment costs are approximately $160 per ton of dry soil. A detailed flowsheet of the ABE process is provided.« less

Gravimetric Analysis of Particulate Matter using Air Samplers Housing Internal Filtration Capsules.

PubMed

O'Connor, Sean; O'Connor, Paula Fey; Feng, H Amy; Ashley, Kevin

2014-10-01

An evaluation was carried out to investigate the suitability of polyvinyl chloride (PVC) internal capsules, housed within air sampling devices, for gravimetric analysis of airborne particles collected in workplaces. Experiments were carried out using blank PVC capsules and PVC capsules spiked with 0,1 - 4 mg of National Institute of Standards and Technology Standard Reference Material ® (NIST SRM) 1648 (Urban Particulate Matter) and Arizona Road Dust (Air Cleaner Test Dust). The capsules were housed within plastic closed-face cassette samplers (CFCs). A method detection limit (MDL) of 0,075 mg per sample was estimated. Precision S r at 0,5 - 4 mg per sample was 0,031 and the estimated bias was 0,058. Weight stability over 28 days was verified for both blanks and spiked capsules. Independent laboratory testing on blanks and field samples verified long-term weight stability as well as sampling and analysis precision and bias estimates. An overall precision estimate Ŝ rt of 0,059 was obtained. An accuracy measure of ±15,5% was found for the gravimetric method using PVC internal capsules.

Gravimetric Analysis of Particulate Matter using Air Samplers Housing Internal Filtration Capsules

PubMed Central

O'Connor, Sean; O'Connor, Paula Fey; Feng, H. Amy

2015-01-01

Summary An evaluation was carried out to investigate the suitability of polyvinyl chloride (PVC) internal capsules, housed within air sampling devices, for gravimetric analysis of airborne particles collected in workplaces. Experiments were carried out using blank PVC capsules and PVC capsules spiked with 0,1 – 4 mg of National Institute of Standards and Technology Standard Reference Material® (NIST SRM) 1648 (Urban Particulate Matter) and Arizona Road Dust (Air Cleaner Test Dust). The capsules were housed within plastic closed-face cassette samplers (CFCs). A method detection limit (MDL) of 0,075 mg per sample was estimated. Precision Sr at 0,5 - 4 mg per sample was 0,031 and the estimated bias was 0,058. Weight stability over 28 days was verified for both blanks and spiked capsules. Independent laboratory testing on blanks and field samples verified long-term weight stability as well as sampling and analysis precision and bias estimates. An overall precision estimate Ŝrt of 0,059 was obtained. An accuracy measure of ±15,5% was found for the gravimetric method using PVC internal capsules. PMID:26435581

Crystallization efficiencies of inorganic polyphosphate oligomers reacted with magnesium and calcium cations using anion-exchange chromatography with particulate formation-laser scattering detector.

PubMed

Ando, Masaki; Imadzu, Sakiyo; Kitagawa, Shinya; Ohtani, Hajime

2010-08-06

A particulate formation-laser scattering detector (PFLSD) was developed and used for evaluating the crystallization efficiency of inorganic polyphosphates (PPs) that reacted with either magnesium or calcium cations. As the solutions for reactive crystallization, 0.5 M ammonium buffer (pH 9.6) containing either 0.15 M MgCl(2) or 0.15 M CaCl(2) (MAP: magnesium ammonium phosphate and HAP: hydroxyapatite solution) were used. In the case of mono- and diphosphate (P1 and P2), the significant dependences of the particulate formation efficiency on various types of both P1/P2 and MAP/HAP reaction solutions were observed with the direct sample injection mode. The PFLSD was hyphenated with the anion-exchange chromatography and the dependence of the particulate formation efficiency on the polymerization degree (n(p)) of PP oligomers, separated chromatographically, was evaluated sequentially. The significant suppression of the particulate formation for PP oligomers was clearly confirmed, i.e., the MAP and HAP reaction solutions did not produce the particulates of the PP oligomers having an n(p) value of more than 3 and 5, respectively. As the overall tendency, the particulate formation efficiency in the case of the HAP solution was superior to that in the case of the MAP solution. Copyright 2010 Elsevier B.V. All rights reserved.

Ambient air particulates and particulate-bound mercury Hg(p) concentrations: dry deposition study over a Traffic, Airport, Park (T.A.P.) areas during years of 2011-2012.

PubMed

Fang, Guor-Cheng; Lin, Yen-Heng; Zheng, Yu-Cheng

2016-02-01

The main purpose of this study was to monitor ambient air particles and particulate-bound mercury Hg(p) in total suspended particulate (TSP) concentrations and dry deposition at the Hung Kuang (Traffic), Taichung airport and Westing Park sampling sites during the daytime and nighttime, from 2011 to 2012. In addition, the calculated/measured dry deposition flux ratios of ambient air particles and particulate-bound mercury Hg(p) were also studied with Baklanov & Sorensen and the Williams models. For a particle size of 10 μm, the Baklanov & Sorensen model yielded better predictions of dry deposition of ambient air particulates and particulate-bound mercury Hg(p) at the Hung Kuang (Traffic), Taichung airport and Westing Park sampling site during the daytime and nighttime sampling periods. However, for particulates with sizes 20-23 μm, the results obtained in the study reveal that the Williams model provided better prediction results for ambient air particulates and particulate-bound mercury Hg(p) at all sampling sites in this study.

Home cage locomotor changes in non-human primates after prolonged welding-fume exposure.

PubMed

Kim, Choong Yong; Sung, Jae Hyuck; Chung, Yong Hyun; Park, Jung Duck; Han, Jeong Hee; Lee, Jong Seong; Heo, Jeong Doo; Yu, Il Je

2013-12-01

To define the relationship between the brain concentration of manganese and neurological signs, such as locomotion, after prolonged welding-fume exposure, cynomolgus monkeys were acclimated for 1 month and then divided into three concentration groups: unexposed, low concentration (31 mg/m(3) total suspended particulate (TSP), 0.9 mg/m(3) of Mn), and high concentration (62 mg/m(3) TSP, 1.95 mg/m(3) of Mn) of TSP. The monkeys were exposed to manual metal-arc stainless steel (MMA-SS) welding fumes for 2 h per day over 8 months in an inhalation chamber system equipped with an automatic fume generator. The home cage locomotor activity and patterns were determined using a camera system over 2-4 consecutive days. After 25 and 32 weeks of exposure, the home cage locomotor activity of the high-concentration primates was found to be 5-6 times higher than that of the unexposed primates, and this increased locomotor activity was maintained for 7 weeks after ceasing the welding-fume exposure, eventually subsiding to three times higher after 13 weeks of recovery. Therefore, the present results, along with our previous observations of a high magnetic resonance imaging (MRI) T1 signal in the globus pallidus and increased blood Mn concentration, indicate that prolonged welding-fume exposure can cause neurobehavioral changes in cynomolgus monkeys.

Estimating labile particulate iron concentrations in coastal waters from remote sensing data

NASA Astrophysics Data System (ADS)

McGaraghan, Anna R.; Kudela, Raphael M.

2012-02-01

Owing to the difficulties inherent in measuring trace metals and the importance of iron as a limiting nutrient for biological systems, the ability to monitor particulate iron concentration remotely is desirable. This study examines the relationship between labile particulate iron, described here as weak acid leachable particulate iron or total dissolvable iron, and easily obtained bio-optical measurements. We develop a bio-optical proxy that can be used to estimate large-scale patterns of labile iron concentrations in surface waters, and we extend this by including other environmental variables in a multiple linear regression statistical model. By utilizing a ratio of optical backscatter and fluorescence obtained by satellite, we identify patterns in iron concentrations confirmed by traditional shipboard sampling. This basic relationship is improved with the addition of other environmental parameters in the statistical linear regression model. The optical proxy detects known temporal and spatial trends in average surface iron concentrations in Monterey Bay. The proxy is robust in that similar performance was obtained using two independent particulate iron data sets, but it exhibits weaker correlations than the full statistical model. This proxy will be a valuable tool for oceanographers seeking to monitor iron concentrations in coastal regions and allows for better understanding of the variability of labile particulate iron in surface waters to complement direct measurement of leachable particulate or total dissolvable iron.

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

DOE PAGES

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.; ...

2017-05-19

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here in this work, we have measured themore » redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). Lastly, we present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.« less

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here in this work, we have measured themore » redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). Lastly, we present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.« less

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

NASA Astrophysics Data System (ADS)

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.; Till, Claire P.; Lee, Jong-Mi; Toner, Brandy M.; Marcus, Matthew A.

2017-08-01

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here we have measured the redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). We present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.

[Pollution load and the first flush effect of phosphorus in urban runoff of Wenzhou City].

PubMed

Zhou, Dong; Chen, Zhen-lou; Bi, Chun-juan

2012-08-01

Five typical rainfalls were monitored in two different research areas of Wenzhou municipality. The pH and concentrations of total phosphorus (TP), dissolved phosphorus (DP), particulate phosphorus (PP), total inorganic carbon (TIC), total organic carbon (TOC), total suspended substances (TSS), BOD5 and COD in six different kinds of urban runoff were measured. The results showed that, the concentrations of TP, DP and PP in different kinds of urban runoff of Wenzhou ranged from 0.01 to 4.32 mg x L(-1), ND to 0.88 mg x L(-1) and ND to 4.31 mg x L(-1), respectively. In the early stages of runoff process PP was dominated, while in the later, the proportion of DP in most of the runoff samples would show a rising trend, especially in roof and outlet runoff. Judged by the event mean concentration (EMC) of TP and DP in these five rainfalls, some kinds of urban runoff could cause environmental pressure to the next level receiving water bodies. Meanwhile, the differences among the TP and DP content (maximum, minimum and mean content) in various urban runoffs were significant, and so were the differences among various rainfall events. According to the M (V) curve, the first flush effect of TP in most kinds of urban runoff was common; while the first flush effect of DP was more difficult to occur comparing with TP. Not only the underlying surface types but also many physico-chemical properties of runoff could affect the concentration of TP in urban runoff. All the results also suggested that different best management plans (BMPs) should be selected for various urban runoff types for the treatment of phosphorus pollution, and reducing the concentration of TSS is considered as one of the effective ways to decrease the pollution load of phosphorus in urban runoff.

Chemical characterization of freshly emitted particulate matter from aircraft exhaust using single particle mass spectrometry

NASA Astrophysics Data System (ADS)

Abegglen, Manuel; Brem, B. T.; Ellenrieder, M.; Durdina, L.; Rindlisbacher, T.; Wang, J.; Lohmann, U.; Sierau, B.

2016-06-01

Non-volatile aircraft engine emissions are an important anthropogenic source of soot particles in the upper troposphere and in the vicinity of airports. They influence climate and contribute to global warming. In addition, they impact air quality and thus human health and the environment. The chemical composition of non-volatile particulate matter emission from aircraft engines was investigated using single particle time-of-flight mass spectrometry. The exhaust from three different aircraft engines was sampled and analyzed. The soot particulate matter was sampled directly behind the turbine in a test cell at Zurich Airport. Single particle analyses will focus on metallic compounds. The particles analyzed herein represent a subset of the emissions composed of the largest particles with a mobility diameter >100 nm due to instrumental restrictions. A vast majority of the analyzed particles was shown to contain elemental carbon, and depending on the engine and the applied thrust the elemental carbon to total carbon ratio ranged from 83% to 99%. The detected metallic compounds were all internally mixed with the soot particles. The most abundant metals in the exhaust were Cr, Fe, Mo, Na, Ca and Al; V, Ba, Co, Cu, Ni, Pb, Mg, Mn, Si, Ti and Zr were also detected. We further investigated potential sources of the ATOFMS-detected metallic compounds using Inductively Coupled Plasma Mass Spectrometry. The potential sources considered were kerosene, engine lubrication oil and abrasion from engine wearing components. An unambiguous source apportionment was not possible because most metallic compounds were detected in several of the analyzed sources.

Traffic signatures in suspended dust at pedestrian levels in semiarid zones: Implications for human exposure

NASA Astrophysics Data System (ADS)

Meza-Figueroa, Diana; González-Grijalva, Belem; Del Río-Salas, Rafael; Coimbra, Rute; Ochoa-Landin, Lucas; Moreno-Rodríguez, Verónica

2016-08-01

Deeper knowledge on dust suspension processes along semiarid zones is critical for understanding potential impacts on human health. Hermosillo city, located in the heart of the Sonoran Desert was chosen to evaluate such impacts. A one-year survey of Total Suspended Particulate Matter (TSPM) was conducted at two different heights (pedestrian and rooftop level). The minimum values of TSPM were reported during monsoon season and winter. Maximum values showed a bimodal distribution, with major peaks associated with increase and decrease of temperature, as well as decreasing humidity. Concentrations of TSPM were significantly exceeded at pedestrian level (∼44% of analyzed days) when compared to roof level (∼18% of analyzed days). Metal concentrations of As, Pb, Cu, Sb, Be, Mg, Ni, and Co were higher at pedestrian level than at roof level. Pixel counting and interpretations based on scanning electron microscopy of dust filters showed a higher percentage of fine particulate fractions at pedestrian level. These fractions occur mainly as metal-enriched agglomerates resembling coarser particles. According to worldwide guidelines, particulate matter sampling should be conducted by monitoring particle sizes equal and inferior to PM10. However, this work suggests that such procedures may compromise risk assessment in semiarid environments, where coarse particles act as main carriers for emergent contaminants related to traffic. This effect is especially concerning at pedestrian level, leading to an underestimation of potential impacts of human exposure. This study brings forward novel aspects that are of relevance for those concerned with dust suspension processes across semiarid regions and related impact on human health.

Reducing soil phosphorus fertility brings potential long-term environmental gains: A UK analysis

NASA Astrophysics Data System (ADS)

Withers, Paul J. A.; Hodgkinson, Robin A.; Rollett, Alison; Dyer, Chris; Dils, Rachael; Collins, Adrian L.; Bilsborrow, Paul E.; Bailey, Geoff; Sylvester-Bradley, Roger

2017-05-01

Soil phosphorus (P) fertility arising from historic P inputs is a major driver of P mobilisation in agricultural runoff and increases the risk of aquatic eutrophication. To determine the environmental benefit of lowering soil P fertility, a meta-analysis of the relationship between soil test P (measured as Olsen-P) and P concentrations in agricultural drainflow and surface runoff in mostly UK soils was undertaken in relation to current eutrophication control targets (30-35 µg P L-1). At agronomic-optimum Olsen P (16-25 mg kg-1), concentrations of soluble reactive P (SRP), total dissolved P (TDP), total P (TP) and sediment-P (SS-P) in runoff were predicted by linear regression analysis to vary between 24 and 183 µg L-1, 38 and 315 µg L-1, 0.2 and 9.6 mg L-1, and 0.31 and 3.2 g kg-1, respectively. Concentrations of SRP and TDP in runoff were much more sensitive to changes in Olsen-P than were TP and SS-P concentrations, which confirms that separate strategies are required for mitigating the mobilisation of dissolved and particulate P forms. As the main driver of eutrophication, SRP concentrations in runoff were reduced on average by 60 µg L-1 (71%) by lowering soil Olsen-P from optimum (25 mg kg-1) to 10 mg kg-1. At Olsen-P concentrations below 12 mg kg-1, dissolved hydrolysable P (largely organic) became the dominant form of soluble P transported. We concluded that maintaining agronomic-optimum Olsen-P could still pose a eutrophication risk, and that a greater research focus on reducing critical soil test P through innovative agro-engineering of soils, crops and fertilisers would give long-term benefits in reducing the endemic eutrophication risk arising from legacy soil P. Soil P testing should become compulsory in priority catchments suffering, or sensitive to, eutrophication to ensure soil P reserves are fully accounted for as part of good fertiliser and manure management.

Reprint of On the link between biomagnetic monitoring and leaf-deposited dust load of urban trees: relationships and spatial variability of different particle size fractions.

PubMed

Hofman, Jelle; Wuyts, Karen; Van Wittenberghe, Shari; Brackx, Melanka; Samson, Roeland

2014-09-01

Biomagnetic monitoring of urban tree leaves has proven to be a good estimator of ambient particulate matter. We evaluated its relevancy by determining leaf area normalised weight (mg m(-2)) and SIRM (A) of leaf-deposited particles within three different size fractions (>10 μm, 3-10 μm and 0.2-3 μm) and the SIRM of the leaf-encapsulated particles. Results showed that throughout the in-leaf season, the trees accumulated on average 747 mg m(-2) of dust on their leaves, of which 74 mg m(-2) was within the 0.2-10 μm (∼PM10) size range and 40 mg m(-2) within the 0.2-3 μm (∼PM3) size range. A significant correlation between the SIRM and weight of the surface-deposited particles confirms the potential of biomagnetic monitoring as a proxy for the amount of leaf-deposited particles. Spatial variation of both SIRM and weight throughout the street canyon suggests traffic and wind as key factors for respectively the source and distribution of urban particulates. Copyright © 2014 Elsevier Ltd. All rights reserved.

Strontium concentrations in corrosion products from residential drinking water distribution systems.

PubMed

Gerke, Tammie L; Little, Brenda J; Luxton, Todd P; Scheckel, Kirk G; Maynard, J Barry

2013-05-21

The United States Environmental Protection Agency (US EPA) will require some U.S. drinking water distribution systems (DWDS) to monitor nonradioactive strontium (Sr(2+)) in drinking water in 2013. Iron corrosion products from four DWDS were examined to assess the potential for Sr(2+) binding and release. Average Sr(2+) concentrations in the outermost layer of the corrosion products ranged from 3 to 54 mg kg(-1) and the Sr(2+) drinking water concentrations were all ≤0.3 mg L(-1). Micro-X-ray adsorption near edge structure spectroscopy and linear combination fitting determined that Sr(2+) was principally associated with CaCO3. Sr(2+) was also detected as a surface complex associated with α-FeOOH. Iron particulates deposited on a filter inside a home had an average Sr(2+) concentration of 40.3 mg kg(-1) and the associated drinking water at a tap was 210 μg L(-1). The data suggest that elevated Sr(2+) concentrations may be associated with iron corrosion products that, if disturbed, could increase Sr(2+) concentrations above the 0.3 μg L(-1) US EPA reporting threshold. Disassociation of very small particulates could result in drinking water Sr(2+) concentrations that exceed the US EPA health reference limit (4.20 mg kg(-1) body weight).

[Coal fineness effect on primary particulate matter features during pulverized coal combustion].

PubMed

Lü, Jian-yi; Li, Ding-kai

2007-09-01

Three kinds of coal differed from fineness were burned in a laboratory-scale drop tube furnace for combustion test, and an 8-stage Andersen particle impactor was employed for sampling the primary particulate matter (PM), in order to study coal fineness effect on primary PM features during pulverized coal combustion. It has been shown that the finer the coal was, the finer the PM produced. PM, emission amount augmented with coal fineness decreased, and the amount of PM10 increased from 13 mg/g to 21 mg/g respectively generated by coarse coal and fine coal. The amount of PM2.5 increased from 2 mg/g to 8 mg/g at the same condition. Constituents and content in bulk ash varied little after three different fineness coal combustion, while the appearance of grading PM differed visibly. The value of R(EE) increased while the coal fineness deceased. The volatility of trace elements which were investigated was Pb > Cr > Zn > Cu > Ni in turn. The concentration of poisonous trace elements was higher which generated from fine coal combustion. The volatilization capacity was influenced little by coal fineness, but the volatilization extent was influenced differently by coal fineness. Fine coal combustion affects worse environment than coarse coal does.

Diurnal variability of chlorinated polycyclic aromatic hydrocarbons in urban air, Japan

NASA Astrophysics Data System (ADS)

Ohura, Takeshi; Horii, Yuichi; Kojima, Mitsuhiro; Kamiya, Yuta

2013-12-01

Concentrations of 3- to 5-ring chlorinated polycyclic aromatic hydrocarbons (ClPAHs) and corresponding PAHs were quantified in 3-h integrated air samples, taken serially over 3-day periods in December 2009 (winter) and August 2010 (summer) in the urban area of Shizuoka, Japan. Twenty species of targeted ClPAHs were detected in both gas and particle phases throughout each campaign. Mean concentrations of total ClPAHs in the winter and summer campaigns were 133 ± 53 pg m-3 and 32 ± 27 pg m-3, respectively. Throughout the campaigns, diurnal variations of total ClPAHs concentrations did not have periodic fluctuation such as decreasing in daytime and increasing in nighttime, observed in PAHs. However, the mean concentrations of particulate ClPAHs trended to be slightly higher in nighttime than in daytime, but not for gaseous ClPAHs. Significant correlations were observed between the concentrations of total ClPAHs and total PAHs in particulate phase, but not in gaseous phase. In addition, for particulate phase, there were significant correlations between the concentrations of individual ClPAHs and corresponding parent PAHs, nitrate, and chlorine in summer, but not in winter. Considering these behaviors of ClPAHs in the air, the emission sources could have features of as follows: (i) specific emission sources emitted both ClPAHs and PAHs in particulate phase could be present in the area; (ii) particulate ClPAHs could be more strongly influenced by local sources and photochemical reactions rather than by transboundary air pollution; (iii) the possible sources could be combustion processes included biomass and fossil fuels.

Fluvial fluxes of water, suspended particulate matter, and nutrients and potential impacts on tropical coastal water Biogeochemistry: Oahu, Hawai'i

USGS Publications Warehouse

Hoover, D.J.; MacKenzie, F.T.

2009-01-01

Baseflow and storm runoff fluxes of water, suspended particulate matter (SPM), and nutrients (N and P) were assessed in conservation, urban, and agricultural streams discharging to coastal waters around the tropical island of Oahu, Hawai'i. Despite unusually low storm frequency and intensity during the study, storms accounted for 8-77% (median 30%) of discharge, 57-99% (median 93%) of SPM fluxes, 11-79% (median 36%) of dissolved nutrient fluxes and 52-99% (median 85%) of particulate nutrient fluxes to coastal waters. Fluvial nutrient concentrations varied with hydrologic conditions and land use; land use also affected water and particulate fluxes at some sites. Reactive dissolved N:P ratios typically were ???16 (the 'Redfield ratio' for marine phytoplankton), indicating that inputs could support new production by coastal phytoplankton, but uptake of dissolved nutrients is probably inefficient due to rapid dilution and export of fluvial dissolved inputs. Particulate N and P fluxes were similar to or larger than dissolved fluxes at all sites (median 49% of total nitrogen, range 22-82%; median 69% of total phosphorus, range 49-93%). Impacts of particulate nutrients on coastal ecosystems will depend on how efficiently SPM is retained in nearshore areas, and on the timing and degree of transformation to reactive dissolved forms. Nevertheless, the magnitude of particulate nutrient fluxes suggests that they represent a significant nutrient source for many coastal ecosystems over relatively long time scales (weeks-years), and that reductions in particulate nutrient loading actually may have negative impacts on some coastal ecosystems.

Mass loading and removal of select illicit drugs in two wastewater treatment plants in New York State and estimation of illicit drug usage in communities through wastewater analysis.

PubMed

Subedi, Bikram; Kannan, Kurunthachalam

2014-06-17

Sewage epidemiology is a rapidly expanding field that can provide information on illicit drug usage in communities, based on the measured concentrations in samples from wastewater treatment plants (WWTPs). In this study, select illicit drugs (six drugs and eight metabolites) were determined on a daily basis for a week in wastewater, suspended particulate matter (SPM), and sludge from two WWTPs in the Albany area in New York State. The WWTP that served a larger population (∼100 000, with a flow rate of 83 300 m(3)/d) showed 3.2 (methadone) to 51 (3,4-methylenedioxyamphetamine; MDA) times higher mass flows of illicit drugs than did the WWTP that served a smaller population (∼15 000, with a flow rate of 6850 m(3)/d). The consumption rate of target illicit drugs in the communities served by the two WWTPs was estimated to range from 1.67 to 3510 mg/d/1000 people. Between the dissolved and particulate phases, the fraction of methadone, 2-ethylidene-1,5-dimethyl-3,3-diphenylpyrrolidine (EDDP), amphetamine, and MDA sorbed to SPM ranged from 34.3% to 41.1% of the total mass in the waste stream. The removal efficiencies of illicit drugs from the two WWTPs ranged from 4% (norcocaine) to 99% (cocaine); however, methamphetamine, methadone, and EDDP showed a negative removal in WWTPs. The environmental emission of illicit drugs from WWTP discharges was calculated to range from 0.38 (MDEA) to 67.5 (EDDP) mg/d/1000 people. Other markers such as caffeine, paraxanthine, nicotine, and cotinine were found to predict the concentrations of select illicit drugs in raw wastewater (r(2) = 0.20-0.79; p ≤ 0.029).

The Effect of Hurricane Lili on the Distribution of Organic Matter in the Inner Louisiana Shelf (Gulf of Mexico, USA)

NASA Astrophysics Data System (ADS)

Clinton, R.; Goni, M. A.; Gisewhite, R.; Monacci, N.; Gordon, E.; Allison, M.; Kineke, G.

2004-12-01

Suspended particles and surface sediments were collected from the inner shelf of the Louisiana central coast following the passage of Hurricane Lili. The elemental and stable isotopic data of these samples were compared to those determined prior to the hurricane. A week after the storm passage, turbidity levels and total suspended sediment concentrations were not that different from pre-storm values, suggesting most of the suspended sediments must have settled soon after the storm passage. Particulate organic carbon (POC) concentrations ranged from 0.1 mg/L to over 2.0 mg/L, with the highest concentrations measured near the seabed and in the inshore portions of the study area. In these locations, suspended particles displayed high POC/Chlorophyll ratios (POC/Chl of 400 to 4,000) and relatively elevated POC/particulate nitrogen ratios (POC/PN of 10 to 14) that indicated their source was locally resuspended seabed sediments. Relatively low POC/Chl (~200) and POC:PN (~7) ratios consistent with significant contributions from phytoplankton were measured only in the surface waters of the most offshore locations. Post hurricane sediment deposition resulted in a storm layer that ranged from 0.5 to 19 cm in thickness. The storm layer was generally composed of silty clays with a coarser, somewhat sandy 1-2 cm basal layer. These storm deposits were characterized by relatively high SA and OC contents. Similarities in the characteristics of the organic matter before and after reinforce the hypothesis that the source of the storm deposits was the finer fraction of locally resuspended seabed sediments, with little evidence for allochthonous land-derived inputs.

Trace-element concentrations and water-soluble ions in size-segregated dust-borne and soil samples in Sistan, southeast Iran

NASA Astrophysics Data System (ADS)

Behrooz, Reza Dahmardeh; Esmaili-Sari, Abbas; Bahramifar, Nader; Kaskaoutis, D. G.; Saeb, Keivan; Rajaei, Fatemeh

2017-04-01

This study analyzes the chemical composition (water-soluble ions and trace elements) of the total suspended particles (TSP) and particulate matter less than 10 and 2.5 μm (PM10 and PM2.5) in the Sistan basin, southeast Iran during the dusty and windy period June - October 2014. Extreme TSP, PM10 and PM2.5 concentrations, means of 1624.8, 433.4 and 320.8 μgm-3, respectively, were recorded in the Zabol sampling site, while the examined water-soluble ions and trace metals constitute small fractions (∼4.1%-17.7%) of the particulate masses. Intense winds on the dust-storm days result in weathering of soil crust and deflation of evaporate minerals from the dried Hamoun lake beds in the Sistan basin. The soil samples are rich in Ca2+, SO42-, Na+ and Cl- revealing the existence of non-sea salts, as well as in Al, Fe and Mg, while the similarity in the chemical composition between soil and airborne samples indicates that the dust events over Sistan are local in origin. In contrast, low concentrations of secondary ions (i.e., nitrate) and heavy metals (i.e., Pb, Cr, Ni, Cu) indicate less anthropogenic and industrial emissions. Enrichment Factor analysis for TSP, PM10 and PM2.5 reveals that the anthropogenic sources contribute a substantial amount in the heavy metals rather than soil crust, while Al, Fe, Sn, Mg are mostly of crustal origin. The results provide essential knowledge in atmospheric chemistry over Sistan and in establishing mitigation strategies for air pollution control.

Assessing soil carbon vulnerability in the Western USA by geospatial modeling of pyrogenic and particulate carbon stocks

NASA Astrophysics Data System (ADS)

Ahmed, Zia U.; Woodbury, Peter B.; Sanderman, Jonathan; Hawke, Bruce; Jauss, Verena; Solomon, Dawit; Lehmann, Johannes

2017-02-01

To predict how land management practices and climate change will affect soil carbon cycling, improved understanding of factors controlling soil organic carbon fractions at large spatial scales is needed. We analyzed total soil organic (SOC) as well as pyrogenic (PyC), particulate (POC), and other soil organic carbon (OOC) fractions in surface layers from 650 stratified-sampling locations throughout Colorado, Kansas, New Mexico, and Wyoming. PyC varied from 0.29 to 18.0 mg C g-1 soil with a mean of 4.05 mg C g-1 soil. The mean PyC was 34.6% of the SOC and ranged from 11.8 to 96.6%. Both POC and PyC were highest in forests and canyon bottoms. In the best random forest regression model, normalized vegetation index (NDVI), mean annual precipitation (MAP), mean annual temperature (MAT), and elevation were ranked as the top four important variables determining PyC and POC variability. Random forests regression kriging (RFK) with environmental covariables improved predictions over ordinary kriging by 20 and 7% for PyC and POC, respectively. Based on RFK, 8% of the study area was dominated (≥50% of SOC) by PyC and less than 1% was dominated by POC. Furthermore, based on spatial analysis of the ratio of POC to PyC, we estimated that about 16% of the study area is medium to highly vulnerable to SOC mineralization in surface soil. These are the first results to characterize PyC and POC stocks geospatially using stratified sampling scheme at the scale of 1,000,000 km2, and the methods are scalable to other regions.

Characterization of urban runoff pollution between dissolved and particulate phases.

PubMed

Wei, Zhang; Simin, Li; Fengbing, Tang

2013-01-01

To develop urban stormwater management effectively, characterization of urban runoff pollution between dissolved and particulate phases was studied by 12 rainfall events monitored for five typical urban catchments. The average event mean concentration (AEMC) of runoff pollutants in different phases was evaluated. The AEMC values of runoff pollutants in different phases from urban roads were higher than the ones from urban roofs. The proportions of total dissolved solids, total dissolved nitrogen, and total dissolved phosphorus in total ones for all the catchments were 26.19%-30.91%, 83.29%-90.51%, and 61.54-68.09%, respectively. During rainfall events, the pollutant concentration at the initial stage of rainfall was high and then sharply decreased to a low value. Affected by catchments characterization and rainfall distribution, the highest concentration of road pollutants might appear in the later period of rainfall. Strong correlations were also found among runoffs pollutants in different phases. Total suspended solid could be considered as a surrogate for particulate matters in both road and roof runoff, while dissolved chemical oxygen demand could be regarded as a surrogate for dissolved matters in roof runoff.

Characterization of particulate emissions from Australian open-cut coal mines: Toward improved emission estimates.

PubMed

Richardson, Claire; Rutherford, Shannon; Agranovski, Igor

2018-06-01

Given the significance of mining as a source of particulates, accurate characterization of emissions is important for the development of appropriate emission estimation techniques for use in modeling predictions and to inform regulatory decisions. The currently available emission estimation methods for Australian open-cut coal mines relate primarily to total suspended particulates and PM 10 (particulate matter with an aerodynamic diameter <10 μm), and limited data are available relating to the PM 2.5 (<2.5 μm) size fraction. To provide an initial analysis of the appropriateness of the currently available emission estimation techniques, this paper presents results of sampling completed at three open-cut coal mines in Australia. The monitoring data demonstrate that the particulate size fraction varies for different mining activities, and that the region in which the mine is located influences the characteristics of the particulates emitted to the atmosphere. The proportion of fine particulates in the sample increased with distance from the source, with the coarse fraction being a more significant proportion of total suspended particulates close to the source of emissions. In terms of particulate composition, the results demonstrate that the particulate emissions are predominantly sourced from naturally occurring geological material, and coal comprises less than 13% of the overall emissions. The size fractionation exhibited by the sampling data sets is similar to that adopted in current Australian emission estimation methods but differs from the size fractionation presented in the U.S. Environmental Protection Agency methodology. Development of region-specific emission estimation techniques for PM 10 and PM 2.5 from open-cut coal mines is necessary to allow accurate prediction of particulate emissions to inform regulatory decisions and for use in modeling predictions. Development of region-specific emission estimation techniques for PM 10 and PM 2.5 from open-cut coal mines is necessary to allow accurate prediction of particulate emissions to inform regulatory decisions and for use in modeling predictions. Comprehensive air quality monitoring was undertaken, and corresponding recommendations were provided.

Exposure to tobacco smoke before and after a partial smoking ban in prison: indoor air quality measures.

PubMed

Ritter, Catherine; Huynh, Cong Khanh; Etter, Jean-François; Elger, Bernice S

2012-09-01

Although exposure to secondhand smoke (SHS) is reportedly high in prison, few studies have measured this in the prison environment, and none have done so in Europe. We measured two indicators of SHS exposure (particulate matter PM10 and nicotine) in fixed locations before (2009) and after (2010) introduction of a partial smoking ban in a Swiss prison. Access to smoking cessation support was available to detainees throughout the study. To measure SHS before and after the introduction of a partial smoking ban. Assessment of particulate matter PM10 (suspended microparticles of 10 μm) and nicotine in ambient air, collected by real-time aerosol monitor and nicotine monitoring devices. The authors observed a significant improvement of nicotine concentrations in the air after the introduction of the smoking ban (before: 7.0 μg/m(3), after: 2.1 μg/m(3), difference 4.9 μg/m(3), 95% CI for difference: 0.52 to 9.8, p=0.03) but not in particulate matter PM10 (before: 0.11 mg/m(3), after: 0.06 mg/m(3), difference 0.06 mg/m(3), 95% CI for difference of means: -0.07 to 0.19, p=0.30). The partial smoking ban was followed by a decrease in nicotine concentrations in ambient air. These improvements can be attributed to the introduction of the smoking ban since no other policy change occurred during this period. Although this shows that concentrations of SHS decreased significantly, protection was still incomplete and further action is necessary to improve indoor air quality.

Chemical determination of particulate nitrogen in San Francisco Bay. Nitrogen: chlorophyll a ratios in plankton

USGS Publications Warehouse

Hager, S.W.; Harmon, D.D.; Alpine, A.E.

1984-01-01

Particulate nitrogen (PN) and chlorophyll a (Chla) were measured in the northern reach of San Francisco Bay throughout 1980. The PN values were calculated as the differences between unfiltered and filtered (0??4 ??m) samples analyzed using the UV-catalyzed peroxide digestion method. The Chla values were measured spectrophotometrically, with corrections made for phaeopigments. The plot of all PN Chla data was found to be non-linear, and the concentration of suspended particulate matter (SPM) was found to be the best selector for linear subsets of the data. The best-fit slopes of PN Chla plots, as determined by linear regression (model II), were interpreted to be the N: Chla ratios of phytoplankton. The Y-intercepts of the regression lines were considered to represent easily-oxidizable detrital nitrogen (EDN). In clear water ( < 10 mg l-1 SPM), the N: Chla ratio was 1??07 ??g-at N per ??g Chla. It decreased to 0??60 in the 10-18 mg l-1 range and averaged 0??31 in the remaining four ranges (18-35, 35-65, 65-155, and 155-470 mg l-1). The EDN values were less than 1 ??g-at N l-1 in the clear water and increased monotonically to almost 12 ??g-at N l-1 in the highest SPM range. The N: Chla ratios for the four highest SPM ranges agree well with data for phytoplankton in light-limited cultures. In these ranges, phytoplankton-N averaged only 20% of the PN, while EDN averaged 39% and refractory-N 41%. ?? 1984.

Marihuana-induced embryotoxicity in the rabbit.

PubMed

Rosenkrantz, H; Grant, R J; Fleischman, R W; Baker, J R

1986-08-01

Few teratogenic studies in animals have been performed simulating marihuana smoking in man. An inhalation marihuana teratology study was conducted in albino rabbits utilizing a modified automatic smoking machine originally developed for rats and mice. Appropriate numbers of dams were exposed to 4 puffs (0.14 mg/kg), 8 puffs (0.72 mg/kg), or 16 puffs (1.44 mg/kg) once daily during gestation Days 6 to 18, and sacrificed on Day 28. Control dams were exposed to 12 puffs of placebo cigarettes or sham-treated for a similar duration in the absence of any smoke. Consistency of smoke was monitored by cigarette weights, total particulate matter, concentrations of carbon monoxide (CO), and tetrahydrocannibinol (THC) in smoke, carboxyhemoglobin levels, and plasma THC levels. Except for a transient decrease in dam respiration rates, other gross toxic signs were absent. Reproductive parameters of mothers were generally normal except for a dose-related embryotoxicity predominantly associated with early resorptions. Despite twice the number of embryo/fetal deaths, there were no marihuana soft tissue or skeletal defects. A correlation between dam demises and CO levels among placebo-exposed animals was related to greater quantities of CO being generated during placebo combustion. It has been shown in the rabbit that marihuana is embryotoxic and not a teratogen at plasma THC levels found in human females.

Generation rates and emission factors of particulate matter and particle-bound polycyclic aromatic hydrocarbons of incense sticks.

PubMed

Lung, Shih-Chun Candice; Hu, Shu-Chuan

2003-02-01

The generation rates and emission factors of particulate matter and associated polycyclic aromatic hydrocarbons (PAHs) from incense burning were assessed in a laboratory setting. The differences among different segments of the same stick, among different sticks of the same kind of incense, and between two kinds of manually made Chih-Chen incense sticks (A and B) were evaluated. Joss sticks were burned inside a 44 cm long elutriator; personal environmental monitors fitted into the top of the elutriator were used to take PM2.5 and PM10 samples of incense smoke. Samples were analyzed for PAHs by gas chromatography-flame ionization Detector. It was found that particle and associated PAHs were generated approximately at 561 microg/min (geometric standard deviation (GSD) = 1.1) and 0.56 microg/min (GSD = 1.1) from Incense A, and at 661 microg/min (GSD = 1.7) and 0.46 microg/min (GSD = 1.3) from Incense B, respectively. One gram of Incense A emitted about 19.8 mg (GSD = 1.1) particulate matter and 17.1 microg (GSD = 1.2) particulate-phase PAHs, while one gram of Incense B produced around 43.6 mg (GSD = 1.1) of particles and 25.2 microg (GSD = 1.2) of particle-bound PAHs. There were significant differences in emissions between Incenses A and B, although they belong to the same class of incense. A 10-20% variability in emissions was observed in the main part of the manually produced stick, and a larger variation was found at both tips of the combustible part.

Analysis of Risks to Oxygen Systems from Particulate and Fiber Contaminants and Derivation of Cleanliness Requirements

NASA Technical Reports Server (NTRS)

Lowrey, Nikki M.

2016-01-01

It has been well documented in the literature that contamination within oxygen systems can create significant fire hazards. Cleanliness limits for nonvolatile residues, ranging from 10 to 500 mg/sq m, have been established for various industries and types of oxygen systems to reduce the risk of ignition of flammable organic films. Particulate cleanliness limits used for oxygen systems vary considerably. Maximum allowed particle size, quantity limits, and allocations for fibers or metallic particles are all variables seen in aerospace cleanliness limits. Particles are known to have the potential to ignite within oxygen systems and must be limited to prevent fires. Particulate contamination may also pose risks to the performance of oxygen systems that are unrelated to ignition hazards. An extensive literature search was performed to better understand the relative importance of particle ignition mechanisms versus other deleterious effects of particles on oxygen systems and to identify rationale for derivation of particulate cleanliness limits for specific systems. The identified risks of different types and sizes of particles and fibers were analyzed. This paper summarizes the risks identified and rationale that may be used to derive particulate cleanliness limits for specific oxygen systems.

Mercury, monomethyl mercury, and dissolved organic carbon concentrations in surface water entering and exiting constructed wetlands treated with metal-based coagulants, Twitchell Island, California

USGS Publications Warehouse

Stumpner, Elizabeth B.; Kraus, Tamara E.C.; Fleck, Jacob A.; Hansen, Angela M.; Bachand, Sandra M.; Horwath, William R.; DeWild, John F.; Krabbenhoft, David P.; Bachand, Philip A.M.

2015-09-02

Following coagulation, but prior to passage through the wetland cells, coagulation treatments transferred dissolved mercury and carbon to the particulate fraction relative to untreated source water: at the wetland cell inlets, the coagulation treatments decreased concentrations of filtered total mercury by 59–76 percent, filtered monomethyl mercury by 40–70 percent, and dissolved organic carbon by 65–86 percent. Passage through the wetland cells decreased the particulate fraction of mercury in wetland cells that received coagulant-treated water. Changes in total mercury, monomethyl mercury, and dissolved organic carbon concentrations resulting from wetland passage varied both by treatment and season. Despite increased monomethyl mercury in the filtered fraction during wetland passage between March and August, the coagulation-wetland systems generally decreased total mercury (filtered plus particulate) and monomethyl mercury (filtered plus particulate) concentrations relative to source water. Coagulation—either alone or in association with constructed wetlands—could be an effective way to decrease concentrations of mercury and dissolved organic carbon in surface water as well as the bioavailability of mercury in the Sacramento–San Joaquin Delta.

40 CFR Appendix L to Part 50 - Reference Method for the Determination of Fine Particulate Matter as PM2.5 in the Atmosphere

Code of Federal Regulations, 2011 CFR

2011-07-01

... not less than 1000 mg/ft2 (1.08 mg/cm2) in accordance with military standard specification (mil. spec... shall also be available via the data output port, as specified in table L-1 of section 7.4.19 of this... available to the sampler operator for verification and change and for output via the data output port along...

ESTIMATED HOURLY PERSONAL EXPOSURES TO AMBIENT AND NON-AMBIENT PARTICULATE MATTER AMONG SENSITIVE POPULATIONS IN SEATTLE, WASHINGTON

EPA Science Inventory

Epidemiological studies of particulate matter (PM) routinely use concentrations measured with stationary outdoor monitors as surrogates for personal exposure. Despite the frequently reported poor correlations between ambient concentrations and total personal exposure, the epidemi...

Green Ocean Amazon 2014/15 High-Volume Filter Sampling: Atmospheric Particulate Matter of an Amazon Tropical City and its Relationship to Population Health Field Campaign Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Machado, C. M.; Santos, Erickson O.; Fernandes, Karenn S.

Manaus, the capital of the Brazilian state of Amazonas, is developing very rapidly. Its pollution plume contains aerosols from fossil fuel combustion mainly due to vehicular emission, industrial activity, and a thermal power plant. Soil resuspension is probably a secondary source of atmospheric particles. The plume transports from Manaus to the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility ARM site at Manacapuru urban pollutants as well as pollutants from pottery factories along the route of the plume. Considering the effects of particulate matter on health, atmospheric particulate matter was evaluated at this site as partmore » of the ARM Facility’s Green Ocean Amazon 2014/15 (GoAmazon 2014/15) field campaign. Aerosol or particulate matter (PM) is typically defined by size, with the smaller particles having more health impact. Total suspended particulate (TSP) are particles smaller than 100 μm; particles smaller than 2.5 μm are called PM2.5. In this work, the PM2.5 levels were obtained from March to December of 2015, totaling 34 samples and TSP levels from October to December of 2015, totaling 17 samples. Sampling was conducted with PM2.5 and TSP high-volume samplers using quartz filters (Figure 1). Filters were stored during 24 hours in a room with temperature (21,1ºC) and humidity (44,3 %) control, in order to do gravimetric analyses by weighing before and after sampling. This procedure followed the recommendations of the Brazilian Association for Technical Standards local norm (NBR 9547:1997). Mass concentrations of particulate matter were obtained from the ratio between the weighted sample and the volume of air collected. Defining a relationship between particulate matter (PM2.5 and TSP) and respiratory diseases of the local population is an important goal of this project, since no information exists on that topic.« less

The Dart estuary, Devon, UK: a case study of chemical dynamics and pollutant mobility

NASA Astrophysics Data System (ADS)

Schuwerack, P.-M. M.; Neal, M.; Neal, C.

2007-01-01

Water, sediments and gill and digestive gland tissues of adult common shore crab (Carcinus maenas), collected at Noss Marina, Sandquay (Britannia Royal Naval College), the Dartmouth Pier, Warfleet Cove and Sugary Cove in the Dart estuary, Devon, UK, were analysed for major, minor and trace elements in spring 2004. Total acid-available measurements analysed included the truly dissolved component and acid-available sediments. Trace metal concentrations are associated largely with particulate and micro-particulate/colloidal phases, the latter being able to pass through standard filter papers. Wide ranges of chemical concentrations were found in the water, sediments and tissues at all the locations. In the water column, 48% of the variance is linked to the sea-salt component (Cl, Na, K, Ca, Mg, B, Li and Sr) and the sediment-associated acid-available fractions are linked to Fe-rich lithogenous materials (Ba, Co, Cu, Fe, Mn, V and Zn). In the sediments, trace elements of Cd, Co, Cr, Fe, Pb, Mn, Ni and V are correlated with the sea salts and associated with the fraction of fine sediments within the total sediment. In the gills and the digestive gland tissues of crabs, high concentrations of Al, Cu and Fe are found and there are correlations between acid-available trace metals of Cu, Cr, Fe, Mn, Ni, Sr and Zn. The relationships between trace metal contaminants, their site-specific concentrations, their temporal and spatial variability and the effects of human activities, such as moorland/agriculture with historic mining and recreational activities in the lower Dart estuary, are discussed.

Fractionation of wastewater characteristics for modelling of Firle Sewage Treatment Works, Harare, Zimbabwe

NASA Astrophysics Data System (ADS)

Muserere, Simon Takawira; Hoko, Zvikomborero; Nhapi, Innocent

Varying conditions are required for different species of microorganisms for the complex biological processes taking place within the activated sludge treatment system. It is against the requirement to manage this complex dynamic system that computer simulators were developed to aid in optimising activated sludge treatment processes. These computer simulators require calibration with quality data input that include wastewater fractionation among others. Thus, this research fractionated raw sewage, at Firle Sewage Treatment Works (STW), for calibration of the BioWin simulation model. Firle STW is a 3-stage activated sludge system. Wastewater characteristics of importance for activated sludge process design can be grouped into carbonaceous, nitrogenous and phosphorus compounds. Division of the substrates and compounds into their constituent fractions is called fractionation and is a valuable tool for process assessment. Fractionation can be carried out using bioassay methods or much simpler physico-chemical methods. The bioassay methods require considerable experience with experimental activated sludge systems and associated measurement techniques while the physico-chemical methods are straight forward. Plant raw wastewater fractionation was carried out through two 14-day campaign periods, the first being from 3 to 16 July 2013 and the second was from 1 to 14 October 2013. According to the Zimbabwean Environmental Management Act, and based on the sensitivity of its catchment, Firle STW effluent discharge regulatory standards in mg/L are COD (<60), TN (<10), ammonia (<0.2), and TP (<1). On the other hand Firle STW Unit 4 effluent quality results based on City of Harare records in mg/L during the period of study were COD (90 ± 35), TN (9.0 ± 3.0), ammonia (0.2 ± 0.4) and TP (3.0 ± 1.0). The raw sewage parameter concentrations measured during the study in mg/L and fractions for raw sewage respectively were as follows total COD (680 ± 37), slowly biodegradable COD (456 ± 23), (0.7), readily biodegradable COD (131 ± 11), (0.2), soluble unbiodegradable COD (40 ± 3), (0.06), particulate unbiodegradable COD (53 ± 3) (0.08), total TKN (40 ± 4) mg/L, ammonia (28 ± 6), (0.68), organically bound nitrogen (12 ± 2), (0.32), TP (15 ± 1.4), orthophosphates (9.6 ± 1.4), (0.64), and organically bound TP (5.4 ± 1.4), (0.36), soluble unbiodegradable TP (0.4 ± 0), (0.03), particulate unbiodegradable TP (0.05 ± 0), (0.003). Thus, wastewater at Firle STW was found to be highly biodegradable suggesting optimisation of biological nutrient removal process will generally achieve effluent regulatory standards compliance. Thus, opportunities for plant optimisation do exist of which modelling with the use of a simulator is recommended to achieve recommended effluent standards in addition to reduction of operating costs.

Changes in blood manganese concentration and MRI t1 relaxation time during 180 days of stainless steel welding-fume exposure in cynomolgus monkeys.

PubMed

Sung, Jae Hyuck; Kim, Choong Yong; Yang, Seoung Oh; Khang, Hyun Soo; Cheong, Hae Kwan; Lee, Jong Seong; Song, Chang-Woo; Park, Jung Duck; Han, Jeong Hee; Chung, Yong Hyun; Choi, Byung Sun; Kwon, Il Hoon; Cho, Myung Haeng; Yu, Il Je

2007-01-01

Welders are at risk of being exposed to high concentrations of welding fumes and developing pneumoconiosis or other welding-fume exposure-related diseases. Among such diseases, manganism resulting from welding-fume exposure remains a controversial issue, as although the movement of manganese into specific brain regions has been established, the similar movement of manganese presented with other metals, such as welding fumes, has not been clearly demonstrated as being similar to that of manganese alone. Meanwhile, the competition between Mn and iron for iron transporters, such as transferrin and DMT-1, to the brain has also been implicated in the welding-fume exposure. Thus, the increased signal intensities in the basal ganglia, including the globus pallidus and subcortical frontal white matter, based on T1-weighted magnetic resonances in welders, require further examination as regards the correspondence with an increased manganese concentration. Accordingly, to investigate the movement of manganese after welding-fume exposure, 6 cynomolgus monkeys were acclimated for 1 mo and assigned to 3 dose groups: unexposed, low dose of (total suspended particulate [TSP] 31 mg/m3, 0.9 mg/m3 of Mn), and high dose of total suspended particulate (62 mg/m3 TSP, 1.95 mg/m3 of Mn). The primates were exposed to manual metal-arc stainless steel (MMA-SS) welding fumes for 2 h/day in an inhalation chamber system equipped with an automatic fume generator for 6 mo. Magnetic resonance imaging (MRI) studies of the basal ganglia were conducted before the initiation of exposure and thereafter every month. During the exposure, the blood chemistry was monitored every 2 wk and the concentrations of metal components in the blood were measured every 2 wk and compared with ambient manganese concentrations. The manganese concentrations in the blood did not show any significant increase until after 2 mo of exposure, and then reached a plateau after 90 days of exposure, showing that an exposure period of at least 60 days was required to build up the blood Mn concentration. Furthermore, as the blood Mn concentration continued to build, a continued decrease in the MRI T1 relaxation time in the basal ganglia was also detected. These data suggested that prolonged inhalation of welding fumes induces a high MRI T1 signal intensity with an elevation of the blood manganese level. The presence of a certain amount of iron or other metals, such as Cr and Ni, in the inhaled welding fumes via inhalation was not found to have a significant effect on the uptake of Mn into the brain or the induction of a high MRI T1 signal intensity.

Distribution of Cd, Pb and Cu between dissolved fraction, inorganic particulate and phytoplankton in seawater of Terra Nova Bay (Ross Sea, Antarctica) during austral summer 2011-12.

PubMed

Illuminati, S; Annibaldi, A; Romagnoli, T; Libani, G; Antonucci, M; Scarponi, G; Totti, C; Truzzi, C

2017-10-01

During the austral summer 2011-2012, the metal quotas of Cd, Pb and Cu in the phytoplankton of Terra Nova Bay (TNB, Antarctica) were measured for the first time. Evolution of all the three metal distributions between dissolved and particulate fractions during the season was also evaluated. Metal concentrations were mainly affected by the dynamic of the pack ice melting and phytoplankton activity. In mid-December when TNB area was covered by a thick pack ice layer and phytoplankton activity was very low, all the three metals were present mainly in their dissolved species. When the pack ice started to melt and the water column characteristics became ideal (i.e. moderate stratification, ice free area), the phytoplankton bloom occurred. Cd showed a nutrient-type behaviour with dissolved and particulate fractions mainly influenced by phytoplankton activity. Cd quota showed a mean value of 0.12 ± 0.07 nmol L -1 (30-100% of the total particulate). Also Cu showed a nutrient-type behaviour, with its quota in phytoplankton varying between 0.08 and 2.1 nmol L -1 (20-100% of the total particulate). Pb features the typical distribution of a scavenged element with very low algal content (0.03 ± 0.02 nmol L -1 , representing 20-50% of the total particulate). The vertical distribution of this element was influenced by several factors (e.g. pack ice melting, atmospheric inputs), the phytoplankton activity affecting Pb behaviour only partially. Metal:C ratios provide valuable information on the biological requirements for Cd, Pb and Cu, leading us to better understand their biogeochemical cycles. Copyright © 2017 Elsevier Ltd. All rights reserved.

Source apportionment of airborne particulates through receptor modeling: Indian scenario

NASA Astrophysics Data System (ADS)

Banerjee, Tirthankar; Murari, Vishnu; Kumar, Manish; Raju, M. P.

2015-10-01

Airborne particulate chemistry mostly governed by associated sources and apportionment of specific sources is extremely essential to delineate explicit control strategies. The present submission initially deals with the publications (1980s-2010s) of Indian origin which report regional heterogeneities of particulate concentrations with reference to associated species. Such meta-analyses clearly indicate the presence of reservoir of both primary and secondary aerosols in different geographical regions. Further, identification of specific signatory molecules for individual source category was also evaluated in terms of their scientific merit and repeatability. Source signatures mostly resemble international profile while, in selected cases lack appropriateness. In India, source apportionment (SA) of airborne particulates was initiated way back in 1985 through factor analysis, however, principal component analysis (PCA) shares a major proportion of applications (34%) followed by enrichment factor (EF, 27%), chemical mass balance (CMB, 15%) and positive matrix factorization (PMF, 9%). Mainstream SA analyses identify earth crust and road dust resuspensions (traced by Al, Ca, Fe, Na and Mg) as a principal source (6-73%) followed by vehicular emissions (traced by Fe, Cu, Pb, Cr, Ni, Mn, Ba and Zn; 5-65%), industrial emissions (traced by Co, Cr, Zn, V, Ni, Mn, Cd; 0-60%), fuel combustion (traced by K, NH4+, SO4-, As, Te, S, Mn; 4-42%), marine aerosols (traced by Na, Mg, K; 0-15%) and biomass/refuse burning (traced by Cd, V, K, Cr, As, TC, Na, K, NH4+, NO3-, OC; 1-42%). In most of the cases, temporal variations of individual source contribution for a specific geographic region exhibit radical heterogeneity possibly due to unscientific orientation of individual tracers for specific source and well exaggerated by methodological weakness, inappropriate sample size, implications of secondary aerosols and inadequate emission inventories. Conclusively, a number of challenging issues and specific recommendations have been included which need to be considered for a scientific apportionment of particulate sources in different geographical regions of India.

Particulate Pyrite Autotrophic Denitrification (PPAD) for Remediation of Nitrate-contaminated Groundwater

NASA Astrophysics Data System (ADS)

Tong, S.; Rodriguez-Gonzalez, L. C.; Henderson, M.; Feng, C.; Ergas, S. J.

2015-12-01

The rapid movement of human civilization towards urbanization, industrialization, and increased agricultural activities has introduced a large amount of nitrate into groundwater. Nitrate is a toxic substance discharged from groundwater to rivers and leads to decreased dissolved oxygen and eutrophication. For this experiment, an electron donor is needed to convert nitrate into non-toxic nitrogen gas. Pyrite is one of the most abundant minerals in the earth's crust making it an ideal candidate as an electron donor. The overall goal of this research was to investigate the potential for pyrite to be utilized as an electron donor for autotrophic denitrification of nitrate-contaminated groundwater. Batch studies of particulate pyrite autotrophic denitrification (PPAD) of synthetic groundwater (100 mg NO3--N L-1) were set up with varying biomass concentration, pyrite dose, and pyrite particle size. Reactors were seeded with mixed liquor volatile suspended solids (VSS) from a biological nitrogen removal wastewater treatment facility. PPAD using small pyrite particles (<0.45mm) resulted in a favorable nitrate removal. The nitrate removal rate increased from 0.26 to 0.34 mg L-1h-1 and then to 0.86 mg L-1h-1, approaching that of the sulfur oxidizing denitrification (SOD) rate of 1.19 mg L-1h-1. Based on Box-Behnken design (BBD) and response surface methodology (RSM), the optimal amount of biomass concentration, pyrite dose, and pyrite particle size were 1,250 mg VSS L-1, 125 g L-1, and 0.815-1.015 mm, respectively. PPAD exhibited substantial nitrate removal rate, lower sulfate accumulation (5.46 mg SO42-/mg NO3--N) and lower alkalinity consumption (1.70 mg CaCO3/mg NO3--N) when compared to SOD (7.54 mg SO42-/mg NO3--N, 4.57 mg CaCO3/mg NO3--N based on stoichiometric calculation). This research revealed that the PPAD process is a promising technique for nitrate-contaminated groundwater treatment and promoted the utilization of pyrite in the field of environmental remediation.

Exposures to thoracic particulate matter, endotoxin, and glucan during post-Hurricane Katrina restoration work, New Orleans 2005-2012.

PubMed

Rando, Roy J; Kwon, Cheol-Woong; Lefante, John J

2014-01-01

In the aftermath of Hurricane Katrina, which devastated the city of New Orleans in August 2005, restoration workers were at risk for respiratory illness from exposure to airborne particles and microbial agents. In support of an epidemiologic investigation of this risk, an exposure assessment for restoration work activities (demolition, trash & debris management, landscape restoration, sewer/waterline repair, and mold remediation) was performed from 2005 to 2012. For 2005 and 2006, Occupational Safety and Health Administration (OSHA) data (n = 730) for personal and area monitoring of total and respirable dust exposures of restoration workers were accessed and analyzed. The most significant exposures were for demolition work, with average respirable dust exposures in 2005 above the action level of 2.5 mg/m(3) and 17.6% of exposures exceeding the permissible exposure limit (PEL) (5 mg/m(3)). Additional personal and area monitoring for thoracic particulate matter was performed from 2007 to 2012 (n = 774) and samples were assayed for endotoxin and (1→3, 1→6)-β-D-glucan (n = 202). In order to integrate the OSHA data with the later monitoring data, three independent predictive models were developed to convert total and respirable dust measures into the equivalent thoracic dust. The three models were not statistically different and the modeling results were in good agreement with an overall coefficient of variation of 16% for the thoracic dust means across work activities estimated by each of the three models. Overall, thoracic dust exposure levels decreased by about an order of magnitude within the first year after Katrina and then more gradually declined and stabilized through 2012. Estimated average exposures to endotoxin and microbial glucan in 2005 were as high as 256 EU/m(3) and 118 μg/m(3), respectively, and likewise were seen to decrease dramatically and stabilize after 2005. The results of this exposure assessment support previously published reports of respiratory illness including sinusitis, toxic pneumonitis, and Katrina Cough among restoration workers in the years immediately after the hurricane.

Distribution patterns of particulate trace metals in the water column and nepheloid layer of the Gulf of Riga.

PubMed

Poikāne, Rita; Carstensen, Jacob; Dahllöf, Ingela; Aigars, Juris

2005-07-01

The dynamics (fate) of trace metals in suspended particulate matter within the Gulf of Riga has not yet been adequately addressed in the scientific literature. Therefore, during a two year period (2001-2002) samples of suspended particulate matter and surface sediments for trace metal analysis were collected in the Gulf of Riga and the Daugava river, and these data were combined with background information from the national marine monitoring program in Latvia. This paper presents a descriptive study of solid phase trace metals (aluminium, iron, cadmium, chromium, copper, manganese, nickel, lead and zinc) dynamics and their spatial distribution within the Gulf of Riga based on Principal Component Analysis and Cluster analysis. Fluvial particulate matter and particulate Al, Fe, Cr and Ni were brought into the Gulf of Riga mainly during spring flood and thereafter quickly diluted by the water masses of the Gulf of Riga. Fine-grained suspended material and particulate Al and Fe were well mixed and evenly distributed through all deepwater basins of the Gulf of Riga. The increase of particulate Mn below the thermocline in August and a strong negative correlation with dissolved oxygen concentrations suggested that particulate Mn in the water column and the sediments were regulated mainly by changing oxic-anoxic conditions in the sediments of the Gulf of Riga. The observed correlation between Al and Fe in the water column is in contrast to that observed in the nepheloid layer where Fe correlated with Mn, obviously due to fast diagenetic processes on sediment surface. The observed negative correlation of Cd and Zn with total carbon and total nitrogen in the nepheloid layer might indicate different sedimentation mechanisms of these elements, however, this assumption is still inconclusive.

Method 440.0 Determination of Carbon and Nitrogen in Sediments and Particulatesof Estuarine/Coastal Waters Using Elemental Analysis

EPA Science Inventory

Elemental analysis is used to determine particulate carbon (PC) and particulate nitrogen (PN) in estuarine and coastal waters and sediment. The method measures the total carbon and nitrogen irrespective of source (inorganic or organic).

Characterisation of diesel particulate emission from engines using commercial diesel and biofuels

NASA Astrophysics Data System (ADS)

Ajtai, T.; Pintér, M.; Utry, N.; Kiss-Albert, G.; Gulyás, G.; Pusztai, P.; Puskás, R.; Bereczky, Á.; Szabados, Gy.; Szabó, G.; Kónya, Z.; Bozóki, Z.

2016-06-01

In this paper, the number concentration and the size distribution of diluted diesel exhaust particulate matter were measured at three different engine operating points in the speed-load range of the engine as follows: 1600 rpm; 50% load, 1900 rpm; 25% load, 1900 rpm; 75% load, adopted from the UN ECE Vehicle Regulation no. 49 (Revision 2) test protocol using pure diesel and biodiesel fuels, as well as their controlled blends. The emitted particulate assembly had lognormal size distribution in the accumulation mode regardless of the engine operational condition and the type of fuel. The total number and volume concentration emitted by the diesel engine decreased with increasing revolution per minute and rated torque in case of all the fuel types. The mixing ratio of the fuels did not linearly affect the total emission but had a minimum at 75% biodiesel content. We also studied the thermal evolution of the emitted particulates using a specially designed thermodenuder (TD) heated at specific temperatures (50 °C, 120 °C, and 250 °C). The first transition, when the temperature was increased from 50 °C to 120 °C resulted in lower number concentrations with small relative shifts of the peak position. However, in case of the second transition, when the temperature reached 250 °C the individual volatile particulates adsorbed onto the surface of soot particles were completely or partly vaporised resulting in lower total number concentrations with a substantial shift in peak position.

Concentration and movement of neonicotinoids as particulate matter downwind during agricultural practices using air samplers in southwestern Ontario, Canada.

PubMed

Forero, Luis Gabriel; Limay-Rios, Victor; Xue, Yingen; Schaafsma, Arthur

2017-12-01

Atmospheric emissions of neonicotinoid seed treatment insecticides as particulate matter in field crops occur mainly for two reasons: 1) due to abraded dust of treated seed generated during planting using vacuum planters, and 2) as a result of disturbances (tillage or wind events) in the surface of parental soils which release wind erodible soil-bound residues. In the present study, concentration and movement of neonicotinoids as particulate matter were quantified under real conditions using passive and active air samplers. Average neonicotinoid concentrations in Total Suspended Particulate (TSP) using passive samplers were 0.48 ng/cm 2 , trace, trace (LOD 0.80 and 0.04 ng/cm 2 for clothianidin and thiamethoxam, respectively), and using active samplers 16.22, 1.91 and 0.61 ng/m 3 during planting, tillage and wind events, respectively. There was a difference between events on total neonicotinoid concentration collected in particulate matter using either passive or active sampling. Distance of sampling from the source field during planting of treated seed had an effect on total neonicotinoid air concentration. However, during tillage distance did not present an effect on measured concentrations. Using hypothetical scenarios, values of contact exposure for a honey bee were estimated to be in the range from 1.1% to 36.4% of the reference contact LD 50 value of clothianidin of 44 ng/bee. Copyright © 2017 Elsevier Ltd. All rights reserved.

Demonstration of Novel Sampling Techniques for Measurement of Turbine Engine Volatile and Non-Volatile Particulate Matter (PM) Emissions

DTIC Science & Technology

2017-03-06

WP-201317) Demonstration of Novel Sampling Techniques for Measurement of Turbine Engine Volatile and Non -volatile Particulate Matter (PM...Engine Volatile and Non -Volatile Particulate Matter (PM) Emissions 6. AUTHOR(S) E. Corporan, M. DeWitt, C. Klingshirn, M.D. Cheng, R. Miake-Lye, J. Peck...the performance and viability of two devices to condition aircraft turbine engine exhaust to allow the accurate measurement of total (volatile and non

Carbonaceous aerosols from prescribed burning of a boreal forest ecosystem. Revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mazurek, M.A.; Cofer, W.R. III; Levine, J.S.

1990-10-01

The identity and ambient mass concentrations of radiatively important carbonaceous aerosols were measured for a boreal forest prescribed burn conducted in northern Ontario, CAN in August 1989. Nonsize-segregated airborne particles were collected for smoldering-fire and full-fire conditions using a helicopter sampling platform. Total carbon (TC), organic carbon (OC) and elemental carbon (EC) were measured. Smoke plume mass concentrations of the OC and EC particles were greatest for full-fire conditions and had ranges of 1.560 to 2.160 mg/m{sup {minus}1} (OC) and 0.120 to 0.160 mg/m{sup {minus}3} (EC) with OC:EC ratios of 10 to 18, respectively. Smoldering fire conditions showed smoke plumemore » OC and EC levels of 0.570--1.030 mg/m{sup {minus}3} (OC) and 0.006--0.050 mg/m{sup {minus}3} (EC) and much higher ratios of OC:EC (21 to 95). These aerosol data indicate the formation of EC particles is greatest during full-fire combustion of boreal forest material relative to smoldering combustion. However, EC particles comprise a minor fraction of the particulate carbon smoke aerosols for both full-fire and smoldering conditions; the major component of carbonaceous smoke aerosols emitted during the prescribed burn is OC. Overall, the OC and EC in-plume smoke aerosol data show nonuniform production of these particles during various stages of the prescribed burn, and major differences in the type of carbonaceous aerosol that is generated (OC versus EC).« less

Carbonaceous aerosols from prescribed burning of a boreal forest ecosystem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mazurek, M.A.; Cofer, W.R. III; Levine, J.S.

1990-10-01

The identity and ambient mass concentrations of radiatively important carbonaceous aerosols were measured for a boreal forest prescribed burn conducted in northern Ontario, CAN in August 1989. Nonsize-segregated airborne particles were collected for smoldering-fire and full-fire conditions using a helicopter sampling platform. Total carbon (TC), organic carbon (OC) and elemental carbon (EC) were measured. Smoke plume mass concentrations of the OC and EC particles were greatest for full-fire conditions and had ranges of 1.560 to 2.160 mg/m{sup {minus}1} (OC) and 0.120 to 0.160 mg/m{sup {minus}3} (EC) with OC:EC ratios of 10 to 18, respectively. Smoldering fire conditions showed smoke plumemore » OC and EC levels of 0.570--1.030 mg/m{sup {minus}3} (OC) and 0.006--0.050 mg/m{sup {minus}3} (EC) and much higher ratios of OC:EC (21 to 95). These aerosol data indicate the formation of EC particles is greatest during full-fire combustion of boreal forest material relative to smoldering combustion. However, EC particles comprise a minor fraction of the particulate carbon smoke aerosols for both full-fire and smoldering conditions; the major component of carbonaceous smoke aerosols emitted during the prescribed burn is OC. Overall, the OC and EC in-plume smoke aerosol data show nonuniform production of these particles during various stages of the prescribed burn, and major differences in the type of carbonaceous aerosol that is generated (OC versus EC).« less

Compatibility and Stability of Rolapitant Injectable Emulsion Admixed with Intravenous Palonosetron Hydrochloride.

PubMed

Wu, George; Yeung, Stanley; Chen, Frank

2017-01-01

Neurokinin-1 receptor antagonist, 5-hydroxytryptamine-3 RA, and dexamethasone combination therapy is standard of care for the prevention of chemotherapy-induced nausea and vomiting. Herein we describe the physical and chemical stability of rolapitant injectable emulsion 166.5 mg in 92.5 mL (185 mg hydrochloride salt) admixed with palonosetron injection 0.25 mg in 5 mL (0.28 mg hydrochloride salt). Admixtures were prepared and stored in two types of container closures (110-mL Crystal Zenith plastic and glass bottles) and four types of intravenous administration sets (or intravenous tubing sets). Assessment of the physical and chemical stability was conducted on the admixtures in the ready-to-use container closure systems as supplied by the manufacturer, stored at room temperature (20°C to 25°C under fluorescent light), and evaluated at 0, 1, and 6 hours; 1 and 2 days; and under refrigeration (2°C to 8°C protected from light) after 1, 3, and 7 days. For admixtures in intravenous tubing sets, the assessment of physicochemical stability was performed after 0 and 7 hours of storage at 20°C to 25°C initially, and then after 20 hours (total 27 hours) at 2°C to 8°C protected from light. Physical stability was assessed by visual examination of the container contents under normal room light, and measuring turbidity and particulate matter. Chemical stability was assessed by measuring the pH of the admixture and determining drug concentrations and impurity levels with high-performance liquid chromatographic analysis. The results indicated that all samples were physically compatible throughout the duration of the study. The pH, turbidity, and particulate matter of the admixture stayed within narrow and acceptable ranges. Rolapitant admixed with palonosetron was chemically stable when admixed in glass and Crystal Zenith bottles for at least 48 hours at room temperature and for 7 days under refrigeration, as well as in the four selected intravenous tubing sets for 7 hours at 20°C to 25°C and then for 20 hours at 2°C to 8°C. No loss of potency of any admixed components occurred in the samples stored at the two temperature ranges and time period studied. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

An Integrated View of Air Mutagenicity

EPA Science Inventory

The mutagenic potency of ambient air particulate material (PM) in the Salmonella mutagenicity assay (revertants/mg PM) varies only ~1 order of magnitude worldwide; however, the mutagenic potency of the air itself (revertants/m3 of air) varies ~5 orders of magnitude (IARC Monograp...

REFERENCE MATERIALS AND QUALITY ASSURANCE FOR THE CHARACTERIZATION OF ORGANIC COMPOUNDS IN PARTICULATE MATTER

EPA Science Inventory

One of the first environmental matrix Standard Reference Materials (SRMs) developed by the National Institute of Standards and Technology (NIST) for determination of organic species was SRM 1649 Urban Dust, ambient total suspended particulate matter (PM) collected in Washington D...

Particle Impact Ignition Test Data on a Stainless Steel Hand Valve

NASA Technical Reports Server (NTRS)

Peralta, Stephen

2010-01-01

This slide presentation reviews the particle impact ignition test of a stainless steel hand valve. The impact of particles is a real fire hazard with stainless steel hand valves, however 100 mg of particulate can be tolerated. Since it is unlikely that 100 mg of stainless steel contaminant particles can be simultaneously released into this type of valve in the WSTF configuration, this is acceptable and within statistical confidence as demonstrated by testing.

Influence of particulates on phosphorus loading exported from farm drainage during a storm event in the Everglades Agricultural Area

NASA Astrophysics Data System (ADS)

Bhadha, J. H.; Lang, T. A.; Daroub, S. H.

2015-12-01

The purpose of this study was to evaluate the influence of particulates on P loading captured during a single storm event. The Everglades Agricultural Area of Florida comprises 280,000 hectares of organic soil farmland artificially drained by ditches, canals and pumps. Phosphorus (P)-enriched suspended particulates in canals are susceptible to transport and can contribute significantly to the overall P loads in drainage water. A settling tank experiment was conducted to capture particulates during tropical storm Isaac in 2012 from three farms approximately 2.4 to 3.6 km2 in size. Farm canal discharge water was collected in a series of two 200 liter settling tanks over a seven-day drainage period, during tropical storm Isaac. Water from the settling tanks was siphoned through Imhoff settling cones, where the particulates were allowed to settle and collected for P-fractionation analyses, and compared to intact sediment cores collected from the bottom of the canals. The discharged particulates contained higher organic matter content (OM), total P, and labile P fractions compared to the canal bottom sediments. Based on the equilibrium P concentrations, surface sediments behave as a source of P to the water column. A seven-day continuous drainage event exported 4.7 to 11.1 metric tons of suspended solids per farm, corresponding to 32 to 63 kg of particulate P being lost to downstream ecosystems. Drainage associated to a single seven-day storm event exported up to 61% of the total annual farm P load. It is evident from this study that short-term, high-intensity storm events can skew annual P loads due to the export of significantly higher particulate matter from farm canals. Exported particulates rich in P can provide a supplemental source of nutrients if captured and replenished back into the farmlands, as a sustainable farming practice.

Characteristics of trace metals in traffic-derived particles in Hsuehshan Tunnel, Taiwan: size distribution, potential source, and fingerprinting metal ratio

NASA Astrophysics Data System (ADS)

Lin, Y.-C.; Tsai, C.-J.; Wu, Y.-C.; Zhang, R.; Chi, K.-H.; Huang, Y.-T.; Lin, S.-H.; Hsu, S.-C.

2015-04-01

Traffic emissions are a significant source of airborne particulate matter (PM) in ambient environments. These emissions contain an abundance of toxic metals and thus pose adverse effects on human health. Size-fractionated aerosol samples were collected from May to September 2013 by using micro-orifice uniform deposited impactors (MOUDIs). Sample collection was conducted simultaneously at the inlet and outlet sites of Hsuehshan Tunnel in northern Taiwan, which is the second-longest freeway tunnel (12.9 km) in Asia. This endeavor aims to characterize the chemical constituents and size distributions, as well as fingerprinting ratios of particulate metals emitted by vehicle fleets. A total of 36 metals in size-resolved aerosols were determined through inductively coupled plasma mass spectrometry. Three major groups - namely, tailpipe emissions (Zn, Pb, and V in fine mode), wear debris (Cu, Cd, Fe, Ga, Mn, Mo, Sb, and Sn), and resuspended dust (Ca, Mg, K, and Rb) - of airborne PM metals were categorized on the basis of the results of enrichment factor, correlation matrix, and principal component analysis. Size distributions of wear-originated metals resembled the pattern of crustal elements, which were predominated by super-micron particulates (PM1-10). By contrast, tailpipe exhaust elements such as Zn, Pb, and V were distributed mainly in submicron particles. By employing Cu as a tracer of wear abrasion, several inter-metal ratios - including Fe / Cu (14), Ba / Cu (1.05), Sb / Cu (0.16), Sn / Cu (0.10), and Ga / Cu (0.03) - served as fingerprints for wear debris. However, the data set collected in this work is useful for further studies on traffic emission inventory and human health effects of traffic-related PM.

Subcellular distribution and activation by non-ionic detergents of guanylate cyclase in cerebral cortex of rat.

PubMed

Deguchi, T; Amano, E; Nakane, M

1976-11-01

Non-ionic detergents stimulated particulate guanylate cyclase activity in cerebral cortex of rat 8- to 12-fold while stimulation of soluble enzyme was 1.3- to 2.5-fold. Among various detergents, Lubrol PX was the most effective one. The subcellular distribution of guanylate cyclase activity was examined with or without 0.5% Lubrol PX. Without Lubrol PX two-thirds of the enzyme activity was detected in the soluble fraction. In the presence of Lubrol PX, however, two-thirds of guanylate cyclase activity was recovered in the crude mitochondrial fraction. Further fractionation revealed that most of the particulate guanylate cyclase activity was associated with synaptosomes. The sedimentation characteristic of the particulate guanylate cyclase activity was very close to those of choline acetyltransferase and acetylcholine esterase activities, two synaptosomal enzymes. When the crude mitochondrial fraction was subfractionated after osmotic shock, most of guanylate cyclase activity as assayed in the absence of Lubrol PX was released into the soluble fraction while the rest of the enzyme activity was tightly bound to synaptic membrane fractions. The total guanylate cyclase activity recovered in the synaptosomal soluble fraction was 6 to 7 times higher than that of the starting material. The specific enzyme activity reached more than 1000 pmol per min per mg protein, which was 35-fold higher than that of the starting material. The membrane bound guanylate cyclase activity was markedly stimulated by Lubrol PX. Guanylate cyclase activity in the synaptosomal soluble fraction, in contrast, was suppressed by the addition of Lubrol PX. The observation that most of guanylate cyclase activity was detected in synaptosomes, some of which was tightly bound to the synaptic membrane fraction upon hypoosmotic treatment, is consistent with the concept that cyclic GMP is involved in neural transmission.

Nutrient transport to the Swan-Canning Estuary, Western Australia

NASA Astrophysics Data System (ADS)

Peters, Norman E.; Donohue, Robert

2001-09-01

Catchment nutrient availability in Western Australia is primarily controlled by the disposal of animal waste and the type and rate of fertilizer application, particularly on the relatively narrow (25 km wide), sandy coastal plain. Nitrogen (N) and phosphorus (P) concentrations and fluxes during the wet season of 15 tributaries, including four urban drains to the Swan-Canning Estuary, were evaluated from 1986 to 1992 and additionally concentrations only were evaluated throughout the year from 1993 to 1996. Concentrations of filtered reactive P (FRP) and total P (TP) were generally low, with the volume-weighted means for all sites being 0·06 mg l-1 and 0·12 mg l-1 respectively. The urban drains had higher TP concentrations (volume-weighted mean of 0·21 mg l-1) than the streams (0·12 mg l-1), with the high concentrations associated with particulate matter. Total inorganic N (TIN, NH4N plus NO3N) and total N (TN), which is of interest to eutrophic status of the N-limited estuary, were likewise low, compared with other developed areas having a similar climate. Both TIN and TN were higher in the urban drains (0·76 mg l-1 and 1·5 mg l-1 respectively) than the streams (0·31 mg l-1 and 1·2 mg l-1 respectively). The Avon River, which drains 98·5% of the 121 000 km2 catchment area, contributes most of the N (0·03 kg ha-1 year-1 or 65%) and a high percentage of the P (<0·01 kg ha-1

Nutrient transport to the Swan - Canning Estuary, Western Australia

USGS Publications Warehouse

Peters, N.E.; Donohue, R.

2001-01-01

Catchment nutrient availability in Western Australia is primarily controlled by the disposal of animal waste and the type and rate of fertilizer application, particularly on the relatively narrow (~25 km wide), sandy coastal plain. Nitrogen (N) and phosphorous (P) concentrations and fluxes during the wet season of 15 tributaries, including four urban drains to the Swan-Canning Estuary, were evaluated from 1986 to 1992 and additionally concentrations only were evaluated throughout the year from 1993 to 1996. Concentrations of filtered reactive P (FRP) and total P (TP) were generally low, with the volume-weighted means for all sites being 0.06 mg 1-1 and 0.12 mg 1-1 respectively. The urban drains had higher TP concentrations (volume-weighted mean of 0.21 mg 1-1) than the streams (0.12 mg 1-1), with the high concentrations associated with particulate matter. Total inorganic N (TIN, NH4N plus NO3N) and total N (TN), which is of interest to eutrophic status of the N-limited estuary, were likewise low, compared with other developed areas having a similar climate. Both TIN and TN were higher in the urban drains (0.76 mg 1-1 and 1.5 mg 1-1 respectively) than the streams (0.31 mg 1-1 and 1.2 mg 1-1 respectively). The Avon River, which drains 98.5% of the 121 000 km2 catchment area, contributes most of the N (0.03 kg ha-1 year-1 or 65%) and a high percentage of the P (<0.01 kg ha-1 year-1 or 32%) to the estuaries. The Avon River nutrient fluxes are much less than other tributaries closer to the estuary. The coastal plain receives significantly higher rainfall (1,200 mm year-1) and has more intense horticulture and animal production than inland areas (<300 mm year-1). Annual rainfall is seasonal, occuring primarily from May through December. The surficial aquifers on the coastal plain generally are sandy with a low nutrient retention capacity, and rapidly transmit soluble and colloidal material in subsurface flow. Ellen Brook, on the coastal plain, drains pastures treated with superphosphate and has the highest FRP (0.51 mg 1-1), TP (0.7 mg 1-1) and TN (2.1 mg 1-1) of any tributary to the estuary. The coastal plain is also undergoing urbanization, particularly in areas adjacent to the estuary. Nutrients are subsequently available for transport during the onset of seasonal wet weather. Perennial baseflow from urban areas is an important source of nutrients. Water yield from the urban areas was high, being as much as 50% of annual rainfall. The timing of the nutrients delivered by the tributaries may be an important control on estuarine ecology. Copyright ?? 2001 John Wiley and Sons, Ltd.

A strategy for reducing particulate contamination on opening glass ampoules and development of evaluation methods for its application.

PubMed

Lee, Kyeong-Ryoon; Chae, Yoon-Jee; Cho, Sung-Eel; Chung, Suk-Jae

2011-12-01

A single-dose glass ampoule was developed for ease of administration. When glass ampoules are opened, resulting in contamination by particulate matter. Reducing its contamination may minimize the risk in patients due to particulates. This study reports on an attempt to reduce insoluble particulate contamination by developing methods for the precise measurement of this. A vacuum machine (VM) was used to reduce the level of insoluble particulate contamination, and a microscopy, scanning electron microscopy-energy dispersive X-ray spectrometer (SEM-EDS) and inductively coupled plasma-atomic emission spectrometer (ICP-AES) were used to evaluate the level of reduction. The method permitted the insoluble particle content to be reduced by up to 87.8 and 89.3% after opening 1 and 2 mL-ampoules, respectively. The morphology of the glass particulate contaminants was very sharp and rough, a condition that can be harmful to human health. The total weight of glass particles in the opened ampoules was determined to be 104 ± 72.9 μg and 30.5 ± 1.00 μg after opening 1 and 2 mL-ampoules when the VM was operated at highest power. The total weights were reduced to 53.6 and 50.6%, respectively for 1 and 2 mL-ampoules, compared to opening by hand. The loss of ampoule contents on opening by the VM was 6.50 and 4.67% for 1 and 2 mL-ampoules, respectively. As a result, the VM efficiently reduced glass particulate contamination and the evaluation methods used were appropriate for quantifying these levels of contamination.

Characterization of Urban Runoff Pollution between Dissolved and Particulate Phases

PubMed Central

Wei, Zhang; Simin, Li; Fengbing, Tang

2013-01-01

To develop urban stormwater management effectively, characterization of urban runoff pollution between dissolved and particulate phases was studied by 12 rainfall events monitored for five typical urban catchments. The average event mean concentration (AEMC) of runoff pollutants in different phases was evaluated. The AEMC values of runoff pollutants in different phases from urban roads were higher than the ones from urban roofs. The proportions of total dissolved solids, total dissolved nitrogen, and total dissolved phosphorus in total ones for all the catchments were 26.19%–30.91%, 83.29%–90.51%, and 61.54–68.09%, respectively. During rainfall events, the pollutant concentration at the initial stage of rainfall was high and then sharply decreased to a low value. Affected by catchments characterization and rainfall distribution, the highest concentration of road pollutants might appear in the later period of rainfall. Strong correlations were also found among runoffs pollutants in different phases. Total suspended solid could be considered as a surrogate for particulate matters in both road and roof runoff, while dissolved chemical oxygen demand could be regarded as a surrogate for dissolved matters in roof runoff. PMID:23935444

An oral multi-particulate, modified release, hydrocortisone replacement therapy that provides physiological cortisol exposure

PubMed Central

Huatan, Hiep; Merke, Deborah; Arlt, Wiebke; Ross, Richard J.

2013-01-01

Objective It is not possible with current hydrocortisone replacement to mimic the diurnal cortisol profile in patients with adrenal insufficiency. Previous attempts with modified release technology were unsuccessful. Our objective was to develop hydrocortisone formulations that recreate the diurnal cortisol profile using multi-particulate technology. Design and Measurements Screening by in-vitro dissolution profiles, pharmacokinetic testing in dexamethasone suppressed dogs and humans, and comparison to a reference population. Setting Field laboratories and clinical research facility. Results Formulations were generated using an enteric (delayed-release) design configuration with an extended (sustained-release) dissolution profile. In-vitro dissolution confirmed delayed and sustained hydrocortisone release. However, in dogs and humans, sustained release resulted in reduced bioavailability. A formulation, DIURF-006, was developed that maintained delayed release but omitted the sustained release functionality. Pharmacokinetic characterisation of DIURF-006 showed that, despite absence of a sustained release component, absorption was sufficiently sustained to deliver extended hydrocortisone absorption. In dexamethasone-suppressed volunteers (n=16) receiving a twice daily ‘toothbrush’ regimen (20mg at 23:00h and 10mg at 07:00h), DIURF-006 gave a similar cortisol profile to physiological cortisol levels: DIURF-006 vs physiological, Geomean AUC 5610 vs 4706 hr*nmol/l, Geomean Cmax 665 vs 594 nmol/l and Median Tmax 8.5h vs clock time 08:12 hours for peak cortisol. The relative bioavailability of DIURF-006 vs hydrocortisone was 89% and cortisol levels increased linearly with doses between 5 and 30mg. Conclusion A multi-particulate oral hydrocortisone formulation with only an enteric coat provides delayed and sustained absorption and when given in a ‘toothbrush’ regimen provides physiological cortisol exposure. PMID:23980724

Chemical determination of particulate nitrogen in San Francisco Bay. Nitrogen: chlorophyll a rations in plankton

USGS Publications Warehouse

Hager, S.W.; Harmon, D.D.; Alpine, A.E.

1984-01-01

Particulate nitrogen (PN) and chlorophyll a (Chla) were measured in the northern reach of San Francisco Bay throughout 1980. The PN values were calculated as the differences between unfiltered and filtered (0·4 μm) samples analyzed using the UV-catalyzed peroxide digestion method. The Chla values were measured spectrophotometrically, with corrections made for phaeopigments. The plot of all PNChla data was found to be non-linear, and the concentration of suspended particulate matter (SPM) was found to be the best selector for linear subsets of the data. The best-fit slopes of PNChla plots, as determined by linear regression (model II), were interpreted to be the N: Chla ratios of phytoplankton. The Y-intercepts of the regression lines were considered to represent easily-oxidizable detrital nitrogen (EDN). In clear water ( < 10 mg l−1 SPM), the N: Chla ratio was 1·07 μg-at N per μg Chla. It decreased to 0·60 in the 10–18 mg l−1 range and averaged 0·31 in the remaining four ranges (18–35, 35–65, 65–155, and 155–470 mg l−1). The EDN values were less than 1 μg-at N l−1 in the clear water and increased monotonically to almost 12 μg-at N l−1 in the highest SPM range. The N: Chla ratios for the four highest SPM ranges agree well with data for phytoplankton in light-limited cultures. In these ranges, phytoplankton-N averaged only 20% of the PN, while EDN averaged 39% and refractory-N 41%.

Environmental assessment of a wood-waste-fired industrial firetube boiler. Volume 1. Technical results. Final report, January 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeRosier, R.; Waterland, L.R.

1987-03-01

The report gives emission results from field tests of a wood-waste-fired industrial firetube boiler. Emission measurements included: continuous monitoring of flue gas emissions: source assessment sampling system (SASS) sampling of the flue-gas with subsequent laboratory analysis of samples to give total flue gas organics in two boiling point ranges, compound category information within these ranges, specific quantitation of the semivolatile organic priority pollutants, and flue gas concentrations of 65 trace elements; Method 5 sampling for particulates; controlled condensation system (CSS) sampling for SO/sub 2/ and SO/sub 3/; and grab sampling of boiler bottom ash for trace element content determinations. Totalmore » organic emissions from the boiler were 5.7 mg/dscm, about 90% of which consisted of volatile compounds.« less

Mechanisms for trace metal enrichment at the surface microlayer in an estuarine salt marsh

USGS Publications Warehouse

Lion, Leonard W.

1982-01-01

The relative contributions of adsorption to particulate surfaces, complexation with surface-active organic ligands and uptake by micro-organisms were evaluated with respect to their importance in the surface microlayer enrichment (‘partitioning’) of Cd, Pb and Cu. The contributions of each process were inferred from field data in which partitioning of the dissolved and particulate forms of Cd, Pb and Cu, total and dissolved organic carbon, particles and total bacteria were observed. In the South San Francisco Bay estuary, particle enrichment appears to control trace metal partitioning. Trace metal association with the particulate phase and the levels of partitioning observed were in the order Pb > Cu > Cd and reflect the calculated equilibrium chemical speciation of these metals in computer-simulated seawater matrices.

Comparison of fine particle measurements from a direct-reading instrument and a gravimetric sampling method.

PubMed

Kim, Jee Young; Magari, Shannon R; Herrick, Robert F; Smith, Thomas J; Christiani, David C

2004-11-01

Particulate air pollution, specifically the fine particle fraction (PM2.5), has been associated with increased cardiopulmonary morbidity and mortality in general population studies. Occupational exposure to fine particulate matter can exceed ambient levels by a large factor. Due to increased interest in the health effects of particulate matter, many particle sampling methods have been developed In this study, two such measurement methods were used simultaneously and compared. PM2.5 was sampled using a filter-based gravimetric sampling method and a direct-reading instrument, the TSI Inc. model 8520 DUSTTRAK aerosol monitor. Both sampling methods were used to determine the PM2.5 exposure in a group of boilermakers exposed to welding fumes and residual fuel oil ash. The geometric mean PM2.5 concentration was 0.30 mg/m3 (GSD 3.25) and 0.31 mg/m3 (GSD 2.90)from the DUSTTRAK and gravimetric method, respectively. The Spearman rank correlation coefficient for the gravimetric and DUSTTRAK PM2.5 concentrations was 0.68. Linear regression models indicated that log, DUSTTRAK PM2.5 concentrations significantly predicted loge gravimetric PM2.5 concentrations (p < 0.01). The association between log(e) DUSTTRAK and log, gravimetric PM2.5 concentrations was found to be modified by surrogate measures for seasonal variation and type of aerosol. PM2.5 measurements from the DUSTTRAK are well correlated and highly predictive of measurements from the gravimetric sampling method for the aerosols in these work environments. However, results from this study suggest that aerosol particle characteristics may affect the relationship between the gravimetric and DUSTTRAK PM2.5 measurements. Recalibration of the DUSTTRAK for the specific aerosol, as recommended by the manufacturer, may be necessary to produce valid measures of airborne particulate matter.

High-rate activated sludge system for carbon management--Evaluation of crucial process mechanisms and design parameters.

PubMed

Jimenez, Jose; Miller, Mark; Bott, Charles; Murthy, Sudhir; De Clippeleir, Haydee; Wett, Bernhard

2015-12-15

The high-rate activated sludge (HRAS) process is a technology suitable for the removal and redirection of organics from wastewater to energy generating processes in an efficient manner. A HRAS pilot plant was operated under controlled conditions resulting in concentrating the influent particulate, colloidal, and soluble COD to a waste solids stream with minimal energy input by maximizing sludge production, bacterial storage, and bioflocculation. The impact of important process parameters such as solids retention time (SRT), hydraulic residence time (HRT) and dissolved oxygen (DO) levels on the performance of a HRAS system was demonstrated in a pilot study. The results showed that maximum removal efficiencies of soluble COD were reached at a DO > 0.3 mg O2/L, SRT > 0.5 days and HRT > 15 min which indicates that minimizing the oxidation of the soluble COD in the high-rate activated sludge process is difficult. The study of DO, SRT and HRT exhibited high degree of impact on the colloidal and particulate COD removal. Thus, more attention should be focused on controlling the removal of these COD fractions. Colloidal COD removal plateaued at a DO > 0.7 mg O2/L, SRT > 1.5 days and HRT > 30 min, similar to particulate COD removal. Concurrent increase in extracellular polymers (EPS) production in the reactor and the association of particulate and colloidal material into sludge flocs (bioflocculation) indicated carbon capture by biomass. The SRT impacted the overall mass and energy balance of the high-rate process indicating that at low SRT conditions, lower COD mineralization or loss of COD content occurred. In addition, the lower SRT conditions resulted in higher sludge yields and higher COD content in the WAS. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of Methods for Analysis of Lead in Air Particulates: An Intra-Laboratory and Inter-Laboratory Comparison

EPA Science Inventory

In 2008, the United States Environmental Protection Agency (USEPA) set a new National Ambient Air Quality Standard (NAAQS) for lead (Pb) in total suspended particulate matter (Pb-TSP) which called for significant decreases in the allowable limits. The Federal Reference Method (FR...

78 FR 22425 - Designation of Areas for Air Quality Planning Purposes; State of Nevada; Total Suspended Particulate

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-16

... carbon monoxide, hydrocarbons, nitrogen dioxide, photochemical oxidant, sulfur dioxide, and particulate... rely on local dust ordinances, completion of local road paving projects, and regulation of emissions from industrial processing activities. Among the local dust ordinances referred to in these four plans...

Particulate oxidative burden associated with firework activity.

PubMed

Godri, Krystal J; Green, David C; Fuller, Gary W; Dall'Osto, Manuel; Beddows, David C; Kelly, Frank J; Harrison, Roy M; Mudway, Ian S

2010-11-01

Firework events are capable of inducing particulate matter (PM) episodes that lead to exceedances of regulatory limit values. As short-term peaks in ambient PM concentration have been associated with negative impacts on respiratory and cardiovascular health, we performed a detailed study of the consequences of firework events in London on ambient air quality and PM composition. These changes were further related to the oxidative activity of daily PM samples by assessing their capacity to drive the oxidation of physiologically important lung antioxidants including ascorbate, glutathione and urate (oxidative potential, OP). Twenty-four hour ambient PM samples were collected at the Marylebone Road sampling site in Central London over a three week period, including two major festivals celebrated with pyrotechnic events: Guy Fawkes Night and Diwali. Pyrotechnic combustion events were characterized by increased gas phase pollutants levels (NO(x) and SO(2)), elevated PM mass concentrations, and trace metal concentrations (specifically Sr, Mg, K, Ba, and Pb). Relationships between NO(x), benzene, and PM(10) were used to apportion firework and traffic source fractions. A positive significant relationship was found between PM oxidative burden and individual trace metals associated with each of these apportioned source fractions. The level of exposure to each source fraction was significantly associated with the total OP. The firework contribution to PM total OP, on a unit mass basis, was greater than that associated with traffic sources: a 1 μg elevation in firework and traffic PM fraction concentration was associated with a 6.5 ± 1.5 OP(T) μg(-1) and 5.2 ± 1.4 OP(T) μg(-1) increase, respectively. In the case of glutathione depletion, firework particulate OP (3.5 ± 0.8 OP(GSH) μg(-1)) considerably exceeded that due to traffic particles (2.2 ± 0.8 OP(GSH) μg(-1)). Therefore, in light of the elevated PM concentrations caused by firework activity and the increased oxidative activity of this PM source, there is value in examining if firework derived PM is related to acute respiratory outcomes.

Used tire recycling to produce granulates: evaluation of occupational exposure to chemical agents.

PubMed

Savary, Barbara; Vincent, Raymond

2011-10-01

Exposure was assessed in four facilities where used tires are turned into rubber granulates. Particulate exposure levels were measured using filter samples and gravimetric analysis. In parallel, volatile organic compounds (VOCs) screening was carried out using samples taken on activated carbon supports, followed by an analysis using a gas chromatograph coupled to a spectrometric detector. The exposure level medians are between 0.58 and 3.95 mg m(-3). Clogging of the textile fiber separation systems can lead to worker exposure; in this case, the measured concentrations can reach 41 mg m(-3). However, in contrast to the data in the literature, VOC levels >1 p.p.m. were not detected. The particulate mixtures deposited on the installation surfaces are complex; some of the chemical agents are toxic to humans. The results of this study indicate significant exposure to complex mixtures of rubber dust. Optimizing exhaust ventilation systems inside the shredders, with a cyclone for example, is essential for reducing the exposure of workers in this rapidly developing sector.

Saharan dust particles in snow samples of Alps and Apennines during an exceptional event of transboundary air pollution.

PubMed

Telloli, Chiara; Chicca, Milvia; Pepi, Salvatore; Vaccaro, Carmela

2017-12-21

Southern European countries are often affected in summer by transboundary air pollution from Saharan dust. However, very few studies deal with Saharan dust pollution at high altitudes in winter. In Italy, the exceptional event occurred on February 19, 2014, colored in red the entire mountain range (Alps and Apennines) and allowed to characterize the particulate matter deposited on snow from a morphological and chemical point of view. Snow samples were collected after this event in four areas in the Alps and one in the Apennines. The particulate matter of the melted snow samples was analyzed by scanning electron microscopy with energy dispersive X-ray spectrometry (SEM-EDS) and by inductively coupled plasma mass spectrometry (ICP-MS). These analyses confirmed the presence of Saharan dust particle components in all areas with similar percentages, supported also by the positive correlations between Mg-Ca, Al-Ca, Al-Mg, and Al-K in all samples.

Particle size distributions of currently used pesticides in ambient air of an agricultural Mediterranean area

NASA Astrophysics Data System (ADS)

Coscollà, Clara; Muñoz, Amalia; Borrás, Esther; Vera, Teresa; Ródenas, Milagros; Yusà, Vicent

2014-10-01

This work presents first data on the particle size distribution of 16 pesticides currently used in Mediterranean agriculture in the atmosphere. Particulate matter air samples were collected using a cascade impactor distributed into four size fractions in a rural site of Valencia Region, during July to September in 2012 and from May to July in 2013. A total of 16 pesticides were detected, including six fungicides, seven insecticides and three herbicides. The total concentrations in the particulate phase (TSP: Total Suspended Particulate) ranged from 3.5 to 383.1 pg m-3. Most of the pesticides (such as carbendazim, tebuconazole, chlorpyrifos-ethyl and chlorpyrifos-methyl) were accumulated in the ultrafine-fine (<1 μm) and coarse (2.5-10 μm) particle size fractions. Others like omethoate, dimethoate and malathion were presented only in the ultrafine-fine size fraction (<1 μm). Finally, diuron, diphenylamine and terbuthylazine-desethyl-2-OH also show a bimodal distribution but mainly in the coarse size fractions.

Analytical techniques and method validation for the measurement of selected semivolatile and nonvolatile organofluorochemicals in air.

PubMed

Reagen, William K; Lindstrom, Kent R; Thompson, Kathy L; Flaherty, John M

2004-09-01

The widespread use of semi- and nonvolatile organofluorochemicals in industrial facilities, concern about their persistence, and relatively recent advancements in liquid chromatography/mass spectrometry (LC/MS) technology have led to the development of new analytical methods to assess potential worker exposure to airborne organofluorochemicals. Techniques were evaluated for the determination of 19 organofluorochemicals and for total fluorine in ambient air samples. Due to the potential biphasic nature of most of these fluorochemicals when airborne, Occupational Safety and Health Administration (OSHA) versatile sampler (OVS) tubes were used to simultaneously trap fluorochemical particulates and vapors from workplace air. Analytical methods were developed for OVS air samples to quantitatively analyze for total fluorine using oxygen bomb combustion/ion selective electrode and for 17 organofluorochemicals using LC/MS and gas chromatography/mass spectrometry (GC/MS). The experimental design for this validation was based on the National Institute of Occupational Safety and Health (NIOSH) Guidelines for Air Sampling and Analytical Method Development and Evaluation, with some revisions of the experimental design. The study design incorporated experiments to determine analytical recovery and stability, sampler capacity, the effect of some environmental parameters on recoveries, storage stability, limits of detection, precision, and accuracy. Fluorochemical mixtures were spiked onto each OVS tube over a range of 0.06-6 microg for each of 12 compounds analyzed by LC/MS and 0.3-30 microg for 5 compounds analyzed by GC/MS. These ranges allowed reliable quantitation at 0.001-0.1 mg/m3 in general for LC/MS analytes and 0.005-0.5 mg/m3 for GC/MS analytes when 60 L of air are sampled. The organofluorochemical exposure guideline (EG) is currently 0.1 mg/m3 for many analytes, with one exception being ammonium perfluorooctanoate (EG is 0.01 mg/m3). Total fluorine results may be used to determine if the individual compounds quantified provide a suitable mass balance of total airborne organofluorochemicals based on known fluorine content. Improvements in precision and/or recovery as well as some additional testing would be needed to meet all NIOSH validation criteria. This study provided valuable information about the accuracy of this method for organofluorochemical exposure assessment.

Mass loading and emission of thirty-seven pharmaceuticals in a typical municipal wastewater treatment plant in Hunan Province, Southern China.

PubMed

Lin, Huiju; Li, Haipu; Chen, Leilei; Li, Lei; Yin, Ling; Lee, Hsiaowan; Yang, Zhaoguang

2018-01-01

The occurrence, fate, mass loading and environmental emission of 37 pharmaceuticals were studied through an integrated approach involving both dissolved and adsorbed phase at a typical wastewater treatment plant in Hunan Province, Southern China. The results displayed the prevalence of 24 and 23 compounds in dissolved phase of influent and effluent, respectively. Fourteen compounds were found adsorbed onto sludge with a mean concentration ranging from 0.85 to 2900μg/kg dry weight. Twelve compounds exhibited high adsorption potential onto suspended particulate matter (SPM) with a mean fraction ranging from 8.8% (trimethoprim) to 97% (tetracycline). Furthermore, SPM showed a diverse absorbability in influent and effluent water circumstance. The overall elimination varied from -16% for lincomycin to 99% for paracetamol, while macrolides were able to withstand the whole treatment process. Mass balance analysis indicated that degradation was the predominant removal pathway for most compounds, and adsorption onto sludge combined with a minor portion of degradation explained for the reduction of tetracyclines and fluoroquinolones, whereas macrolides were recalcitrant to both two processes. The total mass loading was estimated to be up to 2800mg/d/1000 inhabitants and most compounds exhibited lower or comparable level comparing to the global published data. The total environmental emission was estimated up to be 1000mg/d/1000 inhabitants, and a value of 650mg/d/1000 inhabitants was obtained when considering merely the dissolved phase. This work would be helpful for the better understanding of ultimate fate and real pollution of pharmaceuticals in the water environment. Copyright © 2017 Elsevier Inc. All rights reserved.

Inflammatory markers and exposure to airborne particles among workers in a Swedish pulp and paper mill.

PubMed

Westberg, Håkan; Elihn, Karine; Andersson, Eva; Persson, Bodil; Andersson, Lennart; Bryngelsson, Ing-Liss; Karlsson, Cathe; Sjögren, Bengt

2016-07-01

To study the relationship between exposure to airborne particles in a pulp and paper mill and markers of inflammation and coagulation in blood. Personal sampling of inhalable dust was performed for 72 subjects working in a Swedish pulp and paper mill. Stationary measurements were used to study concentrations of total dust, respirable dust, PM10 and PM2.5, the particle surface area and the particle number concentrations. Markers of inflammation, interleukins (IL-1b, IL-6, IL-8, and IL-10), C-reactive protein (CRP), serum amyloid A (SAA), and fibrinogen and markers of coagulation factor VIII, von Willebrand, plasminogen activator inhibitor, and D-dimer were measured in plasma or serum. Sampling was performed on the last day of the work free period of 5 days, before and after the shift the first day of work and after the shifts the second and third day. In a mixed model analysis, the relationship between particulate exposures and inflammatory markers was determined. Sex, age, smoking, and BMI were included as covariates. The average 8-h time-weighted average (TWA) air concentration levels of inhalable dust were 0.30 mg/m(3), range 0.005-3.3 mg/m(3). The proxies for average 8-h TWAs of respirable dust were 0.045 mg/m(3). Significant and consistent positive relations were found between several exposure metrics (PM 10, total and inhalable dust) and CRP, SAA and fibrinogen taken post-shift, suggesting a dose-effect relationship. This study supports a relationship between occupational particle exposure and established inflammatory markers, which may indicate an increased risk of cardiovascular disease.

Geochemical and Hydrologic Controls of Copper-Rich Surface Waters in the Yerba Loca-Mapocho System

NASA Astrophysics Data System (ADS)

Pasten, P.; Montecinos, M.; Coquery, M.; Pizarro, G. E.; Abarca, M. I.; Arce, G. J.

2015-12-01

Andean watersheds in Northern and Central Chile are naturally enriched with metals, many of them associated to sulfide mineralizations related to copper mining districts. The natural and anthropogenic influx of toxic metals into drinking water sources pose a sustainability challenge for cities that need to provide safe water with the smallest footprint. This work presents our study of the transformations of copper in the Yerba Loca-Mapocho system. Our sampling campaign started from the headwaters at La Paloma Glacier and continues to the inlet of the San Enrique drinking water treatment plant, a system feeding municipalities in the Eastern area of Santiago, Chile. Depending on the season, total copper concentrations go as high as 22 mg/L for the upper sections, which become diluted to <5 mg/L downstream. pH ranged from 3 to 5.6 while suspended solids ranged from <10 to 100 mg/L. We used Geochemist Workbench to assess copper speciation and to evaluate the thermodynamic controls for the formation and dissolution of solid phases. A sediment trap was used to concentrate suspended particulate matter, which was analyzed with ICP-MS, TXRF (total reflection X ray fluorescence) and XRD (X-ray diffraction). Major elements detected in the precipitates were Al (200 g/kg), S (60 g/kg), and Cu (6 g/kg). Likely solid phases include hydrous amorphous phases of aluminum hydroxides and sulfates, and copper hydroxides/carbonates. Efforts are undergoing to find the optimal mixing ratios between the acidic stream and more alkaline streams to maximize attenuation of dissolved copper. The results of this research could be used for enhancing in-stream natural attenuation of copper and reducing treatment needs at the drinking water facility. Acknowledgements to Fondecyt 1130936 and Conicyt Fondap 15110020

Variation in the Effect of Particulate Matter on Pulmonary Function in Schoolchildren in Western Japan and Its Relation with Interleukin-8.

PubMed

Watanabe, Masanari; Noma, Hisashi; Kurai, Jun; Sano, Hiroyuki; Kitano, Hiroya; Saito, Rumiko; Kimura, Yutaka; Aiba, Setsuya; Oshimura, Mitsuo; Shimizu, Eiji

2015-11-09

This study aimed to investigate the effects of particulate matter (PM) on pulmonary function in schoolchildren, as well as the relationships of these effects with interleukin-8. Morning peak expiratory flow (PEF) was measured daily in 399 children during April-May 2012, and in 384 of these children during March-May 2013. PEF's association with the daily levels of suspended particulate matter (SPM) and PM < 2.5 mm (PM2.5) was estimated using a linear mixed model. Interleukin-8 promoter activity was assessed in THP-G8 cells stimulated by fallen PM collected at Tottori University Hospital during four periods (two in 2012 and two in 2013). An increase of 14.0 mg/m³ in SPM led to PEF changes of -2.16 L/min in 2012 and -0.81 L/min in 2013, respectively. An increment of 10.7 mg/m³ in PM2.5 was associated with PEF changes of -2.58 L/min in 2012 and -0.55 L/min in 2013, respectively. These associations were only significant in 2012. Interleukin-8 promoter activity was significantly higher in both periods of 2012 than in 2013. There was a significant association between pulmonary function in schoolchildren and daily levels of SPM and PM2.5, but this association may differ depending on the PM's ability to elicit interleukin-8 production.

Impacts of anthropogenic pressures on the water quality of the Gironde Estuary (SW France) from the Urban Agglomeration of Bordeaux: spatial characterization and inputs of trace metal elements (Ag, As, Cd, Cu, Pb and Zn)

NASA Astrophysics Data System (ADS)

Kessaci, Kahina; Coynel, Alexandra; Blanc, Gérard; Deycard, Victoria N.; Derriennic, Hervé; Schäfer, Jörg

2014-05-01

Recent European legislation (2000/60/CE) has listed eight trace metal elements as priority toxic substances for water quality. Urban metal inputs into hydrosystems are of increasing interest to both scientists and managers facing restrictive environmental protection policies, population increase and changing metal applications. The Gironde Estuary (SW France; 625 km2) is known for its metal/metalloid pollution originating from industrial (e.g. Cd, Zn, Cu, As, Ag, Hg) or agricultural sources (e.g. Cu) in the main fluvial tributaries (Garonne and Dordogne Rivers). However, little peer-reviewed scientific work has addressed the impact of urban sources on the Gironde Estuary, especially the Urban Agglomeration of Bordeaux (~1 million inhabitants) located on the downstream branch of the Garonne River. In this study, a snapshot sampling campaign was performed in 2011 for characterizing the spatial distribution of dissolved and particulate metal/metalloid (As, Ag, Cd, Pb, Zn, Cu) concentrations in three suburban watersheds: the Jalle of Blanquefort (330 km2), Eau Bourde (140 km2), and Peugue (112 km2). Furthermore, particulate metal Enrichment Factors (EF) were calculated using local geochemical background measured at the bottom of a sediment core (492 cm). Results indicated that metal concentrations displayed a high spatial variability depending on the suburban watershed and the studied element. Local concentrations anomalies were observed for: (i) As in the Eau Bourde River in dissolved (4.2 μg/l) and particulate phases (246 mg/kg; EF= 20) and attributed to a nearby industrial incinerator; (ii) Zn in the Peugue River with maximum dissolved and particulate concentrations of 87 μg/l and 1580 mg/kg (EF=17), respectively, probably due to urban habitation runoff; (iii) Ag in the Jalle of Blanquefort River with high dissolved (74 ng/l) and particulate concentrations (33.7 mg/kg; EF=117) due to industrial activities in the downstream part. Based on hydro-geochemical monitoring of both suburban rivers and local wastewater treatment plants (WWTPs), we present a first estimate of metal/metalloid fluxes and compare them to the respective loads in the Garonne River. Our results suggest that suburban metal inputs may significantly increase metal concentrations and fluxes in the fluvial Gironde Estuary, especially for Ag due to inputs exported by WWTPS and the Jalle of Blanquefort River.

Sub-lethal effects of water-based drilling muds on the deep-water sponge Geodia barretti.

PubMed

Edge, Katelyn J; Johnston, Emma L; Dafforn, Katherine A; Simpson, Stuart L; Kutti, Tina; Bannister, Raymond J

2016-05-01

Offshore oil and gas activities can result in the discharge of large amounts of drilling muds. While these materials have generally been regarded as non-toxic to marine organisms, recent studies have demonstrated negative impacts to suspension feeding organisms. We exposed the arctic-boreal sponge Geodia barretti to the primary particulate components of two water-based drilling muds; barite and bentonite. Sponges were exposed to barite, bentonite and a natural reference sediment at a range of total suspended solid concentrations (TSS = 0, 10, 50 or 100 mg/L) for 12 h after which we measured a suite of biomarker responses (lysosomal membrane stability, lipid peroxidation and glutathione). In addition, we compared biomarker responses, organic energy content and metal accumulation in sponges, which had been continuously or intermittently exposed to suspended barite and natural sediment for 14 d at relevant concentrations (10 and 30 mg TSS/L). Lysosomal membrane stability was reduced in the sponges exposed to barite at 50 and 100 mg TSS/L after just 12 h and at 30 mg TSS/L for both continuous and intermittent exposures over 14 d. Evidence of compromised cellular viability was accompanied by barite analysis revealing concentrations of Cu and Pb well above reference sediments and Norwegian sediment quality guidelines. Metal bioaccumulation in sponge tissues was low and the total organic energy content (determined by the elemental composition of organic tissue) was not affected. Intermittent exposures to barite resulted in less toxicity than continuous exposure to barite. Short term exposures to bentonite did not alter any biomarker responses. This is the first time that these biomarkers have been used to indicate contaminant exposure in an arctic-boreal sponge. Our results illustrate the potential toxicity of barite and the importance of assessments that reflect the ways in which these contaminants are delivered under environmentally realistic conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Monsoon control on trace metal fluxes in the deep Arabian Sea

NASA Astrophysics Data System (ADS)

Nair, T. M. Balakrishnan

2006-08-01

Particulate fluxes of aluminium, iron, magnesium and titanium were measured using six time-series sediment traps deployed in the eastern, central and western Arabian Sea. Annual Al fluxes at shallow and deep trap depths were 0.47 and 0.46 g m-2 in the western Arabian Sea, and 0.33 and 0.47 g m-2 in the eastern Arabian Sea. There is a difference of about 0.9-1.8 g m-2y-1 in the lithogenic fluxes determined analytically (residue remaining after leaching out all biogenic particles) and estimated from the Al fluxes in the western Arabian Sea. This arises due to higher fluxes of Mg (as dolomite) in the western Arabian Sea (6-11 times higher than the eastern Arabian Sea). The estimated dolomite fluxes at the western Arabian Sea site range from 0.9 to 1.35gm-2y-1. Fe fluxes in the Arabian Sea were less than that of the reported atmospheric fluxes without any evidence for the presence of labile fraction/excess of Fe in the settling particles. More than 75% of Al, Fe, Ti and Mg fluxes occurred during the southwest (SW) monsoon in the western Arabian Sea. In the eastern Arabian Sea, peak Al, Fe, Mg and Ti fluxes were recorded during both the northeast (NE) and SW monsoons. During the SW monsoon, there exists a time lag of around one month between the increases in lithogenic and dolomite fluxes. Total lithogenic fluxes increase when the southern branch of dust bearing northwesterlies is dragged by the SW monsoon winds to the trap locations. However, the dolomite fluxes increase only when the northern branch of the northwesterlies (which carries a huge amount of dolomite accounting 60% of the total dust load) is dragged, from further north, by SW monsoon winds. The potential for the use of Mg/Fe ratio as a paleo-monsoonal proxy is examined.

Mobility of Particulate and Dissolved Munitions Constituents in the Vadose Zone at Operational Ranges

DTIC Science & Technology

2011-08-05

rates with an identical film thickness value . Our results indicated that breakthrough curves at concentrations less than the compound’s solubility...soil microorganisms , respectively (Clausen et al., 2006). Consequently, the risk of contamination to aquifers beneath military operational ranges was...RDX sorption was carried out in the e 0-60 mg/L and 0-15 mg/L respectively. 0.5 g soil was added to 30 mL solutions of TNT and RDX adjusted for

Distribution and transport of particle-bound polycyclic aromatic hydrocarbons in a river-influenced continental margin: the northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Adhikari, P. L.; Maiti, K.

2017-12-01

Polycyclic aromatic hydrocarbons (PAHs) are particle-reactive and get preferentially sorbed on particulate organic carbon (POC), thus, the transport and fate of POC in aquatic systems plays an important role in biogeochemical cycling of PAHs. In this study, we examine POC and PAHs in finer suspended particulate matter collected from the Louisiana coast, shelf and slope - progressively south-west transect along the direction of the Mississippi River plume, and also from a transect of Atchafalaya River. The concentrations of total particulate PAHs (ΣPAH43) varied between 0.92 to 7.04 ng/L, while POC varied between 4 to 131 µg/L. The concentrations of total particulate ΣPAH43 as well as individual PAH analytes were significantly positively correlated to the concentrations of POC which indicates that the concentrations and transport of POC plays an important role in distribution of PAHs in marine systems. The river influence, characterized by the change in salinity, had significant negative correlation with both the concentrations of particulate PAHs and POC. These results show that the Mississippi River derived particle influx can be an important vector in delivering particle-reactive hydrophobic organic pollutants such as PAHs into the river dominated continental ecosystems in the northern Gulf of Mexico. The underlying seafloor sediment PAHs' concentration and accumulation rates were not correlated to the water column particulate PAH and POC concentrations, which is attributed to re-mineralization during vertical transport, sediment resuspension/redistribution and different timescales of comparison.

Source apportionment of ambient PM10 and PM2.5 in Haikou, China

NASA Astrophysics Data System (ADS)

Fang, Xiaozhen; Bi, Xiaohui; Xu, Hong; Wu, Jianhui; Zhang, Yufen; Feng, Yinchang

2017-07-01

In order to identify the sources of PM10 and PM2.5 in Haikou, 60 ambient air samples were collected in winter and spring, respectively. Fifteen elements (Na, Mg, Al, Si, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn and Pb), water-soluble ions (SO42 - and NO3-), and organic carbon (OC) and elemental carbon (EC) were analyzed. It was clear that the concentration of particulate matter was higher in winter than in spring. The value of PM2.5/PM10 was > 0.6. Moreover, the proportions of TC, ions, Na, Al, Si and Ca were more high in PM10 and PM2.5. The SOC concentration was estimated by the minimum OC/EC ratio method, and deducted from particulate matter compositions when running CMB model. According to the results of CMB model, the resuspended dust (17.5-35.0%), vehicle exhaust (14.9-23.6%) and secondary particulates (20.4-28.8%) were the major source categories of ambient particulate matter. Additionally, sea salt also had partial contribution (3-8%). And back trajectory analysis results showed that particulate matter was greatly affected by regional sources in winter, while less affected in spring. So particulate matter was not only affected by local sources, but also affected by sea salt and regional sources in coastal cities. Further research could focuses on establishing the actual secondary particles profiles and identifying the local and regional sources of PM at once by one model or analysis method.

Optical properties of size fractions of suspended particulate matter in littoral waters of Québec

NASA Astrophysics Data System (ADS)

Mohammadpour, Gholamreza; Gagné, Jean-Pierre; Larouche, Pierre; Montes-Hugo, Martin A.

2017-11-01

Mass-specific absorption (ai∗(λ)) and scattering (bi∗(λ)) coefficients were derived for four size fractions (i = 0.2-0.4, 0.4-0.7, 0.7-10, and > 10 µm, λ = wavelength in nm) of suspended particulate matter (SPM) and with samples obtained from surface waters (i.e., 0-2 m depth) of the Saint Lawrence Estuary and Saguenay Fjord (SLE-SF) during June of 2013. For the visible-near-infrared spectral range (i.e., λ = 400-710 nm), mass-specific absorption coefficients of total SPM (i.e., particulates > 0.2 µm) (hereafter aSPM∗) had low values (e.g., < 0.01 m2 g-1 at λ = 440 nm) in areas of the lower estuary dominated by particle assemblages with relatively large mean grain size and high particulate organic carbon and chlorophyll a per unit of mass of SPM. Conversely, largest aSPM∗ values (i.e., > 0.05 m2 g-1 at λ = 440 nm) corresponded with locations of the upper estuary and SF where particulates were mineral-rich and/or their mean diameter was relatively small. The variability of two optical proxies (the spectral slope of particulate beam attenuation coefficient and the mass-specific particulate absorption coefficient, hereafter γ and Svis, respectively) with respect to changes in particle size distribution (PSD) and chemical composition was also examined. The slope of the PSD was correlated with bi∗(550) (Spearman rank correlation coefficient ρs up to 0.37) and ai∗(440) estimates (ρs up to 0.32) in a comparable way. Conversely, the contribution of particulate inorganic matter to total mass of SPM (FSPMPIM) had a stronger correlation with ai∗ coefficients at a wavelength of 440 nm (ρs up to 0.50). The magnitude of γ was positively related to FSPMi or the contribution of size fraction i to the total mass of SPM (ρs up to 0.53 for i = 0.2-0.4 µm). Also, the relation between γ and FSPMPIM variability was secondary (ρs = -0.34, P > 0.05). Lastly, the magnitude of Svis was inversely correlated with aSPM∗(440) (ρs = -0.55, P = 0.04) and FSPMPIM (ρs = -0.62, P = 0.018) in sampling locations with a larger marine influence (i.e., lower estuary).

Particulate exhaust emissions from an experimental combustor. [gas turbine engine

NASA Technical Reports Server (NTRS)

Norgren, C. T.; Ingebo, R. D.

1975-01-01

The concentration of dry particulates (carbon) in the exhaust of an experimental gas turbine combustor was measured at simulated takeoff operating conditions and correlated with the standard smoke-number measurement. Carbon was determined quantitatively from a sample collected on a fiberglass filter by converting the carbon in the smoke sample to carbon dioxide and then measuring the volume of carbon dioxide formed by gas chromatography. At a smoke of 25 (threshold of visibility of the smoke plume for large turbojets) the carbon concentration was 2.8 mg carbon/cu m exhaust gas, which is equivalent to an emission index of 0.17 g carbon/kg fuel.

St. Louis demonstration final report: refuse processing plant equipment, facilities, and environmental evaluations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscus, D.E.; Gorman, P.G.; Schrag, M.P.

1977-09-01

The results are presented of processing plant evaluations of the St. Louis-Union Electric Refuse Fuel Project, including equipment and facilities as well as assessment of environmental emissions at both the processing and the power plants. Data on plant material flows and operating parameters, plant operating costs, characteristics of plant material flows, and emissions from various processing operations were obtained during a testing program encompassing 53 calendar weeks. Refuse derived fuel (RDF) is the major product (80.6% by weight) of the refuse processing plant, the other being ferrous metal scrap, a marketable by-product. Average operating costs for the entire evaluation periodmore » were $8.26/Mg ($7.49/ton). The average overall processing rate for the period was 168 Mg/8-h day (185.5 tons/8-h day) at 31.0 Mg/h (34.2 tons/h). Future plants using an air classification system of the type used at the St. Louis demonstration plant will need an emissions control device for particulates from the large de-entrainment cyclone. Also in the air exhaust from the cyclone were total counts of bacteria and viruses several times higher than those of suburban ambient air. No water effluent or noise exposure problems were encountered, although landfill leachate mixed with ground water could result in contamination, given low dilution rates.« less

Performance characteristics of a low-volume PM10 sampler

USDA-ARS?s Scientific Manuscript database

Four identical PM10 pre-separators, along with four identical low-volume (1m3 hr-1) total suspended particulate (TSP) samplers were tested side-by-side in a controlled laboratory particulate matter (PM) chamber. The four PM10 and four TSP samplers were also tested in an oil pipe-cleaning field to ev...

77 FR 32632 - Ambient Air Monitoring Reference and Equivalent Methods: Designation of Three New Equivalent Methods

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... Hydrogen Peroxide Filter Extraction'' In this method, total suspended particulate matter (TSP) is collected on glass fiber filters according to 40 CFR Appendix G to part 50, EPA Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From Ambient Air. The filter samples are...

EnviroAtlas - Atmospheric Nitrogen Deposition by 12-digit HUC for the Conterminous United States (2002)

EPA Pesticide Factsheets

This EnviroAtlas dataset includes annual nitrogen and sulfur deposition within each 12-digit HUC subwatershed for the year 2002. Values are provided for total oxidized nitrogen (HNO3, NO, NO2, N2O5, NH3, HONO, PAN, organic nitrogen, and particulate NO3), oxidized nitrogen wet deposition, oxidized nitrogen dry deposition, total reduced nitrogen (NH3 and particulate NH4), reduced nitrogen dry deposition, reduced nitrogen wet deposition, total dry nitrogen deposition, total wet nitrogen deposition, total nitrogen deposition (wet+dry), total sulfur (SO2 + particulate SO4) dry deposition, total sulfur wet deposition, and total sulfur deposition. The dataset is based on output from the Community Multiscale Air Quality modeling system (CMAQ) v5.0.2 run using the bidirectional flux option for the 12-km grid size for the US, Canada, and Mexico. The CMAQ output has been post-processed to adjust the wet deposition for errors in the location and amount of precipitation and for regional biases in the TNO3 (HNO3 + NO3), NHx (NH4 + NH3), and sulfate wet deposition. Model predicted values of dry deposition were not adjusted. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadab

EnviroAtlas - Atmospheric Nitrogen and Sulfur Deposition by 12-digit HUC for the Conterminous United States (2011)

EPA Pesticide Factsheets

This EnviroAtlas dataset includes annual nitrogen and sulfur deposition within each 12-digit HUC subwatershed for the year 2011. Values are provided for total oxidized nitrogen (HNO3, NO, NO2, N2O5, NH3, HONO, PAN, organic nitrogen, and particulate NO3), oxidized nitrogen wet deposition, oxidized nitrogen dry deposition, total reduced nitrogen (NH3 and particulate NH4), reduced nitrogen dry deposition, reduced nitrogen wet deposition, total dry nitrogen deposition, total wet nitrogen deposition, total nitrogen deposition (wet+dry), total sulfur (SO2 + particulate SO4) dry deposition, total sulfur wet deposition, and total sulfur deposition. The dataset is based on output from the Community Multiscale Air Quality modeling system (CMAQ) run using the bidirectional flux option for the 12-km grid size for the US, Canada, and Mexico. The CMAQ output has been post-processed to adjust the wet deposition for errors in the location and amount of precipitation and for regional biases in the TNO3 (HNO3 + NO3), NHx (NH4 + NH3), and sulfate wet deposition. Model predicted values of dry deposition were not adjusted. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data

EnviroAtlas - Atmospheric Nitrogen Deposition by 12-digit HUC for the Conterminous United States (2006)

EPA Pesticide Factsheets

This EnviroAtlas dataset includes annual nitrogen and sulfur deposition within each 12-digit HUC subwatershed for the year 2006. Values are provided for total oxidized nitrogen (HNO3, NO, NO2, N2O5, NH3, HONO, PAN, organic nitrogen, and particulate NO3), oxidized nitrogen wet deposition, oxidized nitrogen dry deposition, total reduced nitrogen (NH3 and particulate NH4), reduced nitrogen dry deposition, reduced nitrogen wet deposition, total dry nitrogen deposition, total wet nitrogen deposition, total nitrogen deposition (wet+dry), total sulfur (SO2 + particulate SO4) dry deposition, total sulfur wet deposition, and total sulfur deposition. The dataset is based on output from the Community Multiscale Air Quality modeling system (CMAQ) run using the bidirectional flux option for the 12-km grid size for the US, Canada, and Mexico. The CMAQ output has been post-processed to adjust the wet deposition for errors in the location and amount of precipitation and for regional biases in the TNO3 (HNO3 + NO3), NHx (NH4 + NH3), and sulfate wet deposition. Model predicted values of dry deposition were not adjusted. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable dat

In situ phytoplankton absorption, fluorescence emission, and particulate backscattering spectra determined from reflectance

NASA Technical Reports Server (NTRS)

Roesler, Collin S.; Pery, Mary Jane

1995-01-01

An inverse model was developed to extract the absortion and scattering (elastic and inelastic) properties of oceanic constituents from surface spectral reflectance measurements. In particular, phytoplankton spectral absorption coefficients, solar-stimulated chlorophyll a fluorescence spectra, and particle backscattering spectra were modeled. The model was tested on 35 reflectance spectra obtained from irradiance measurements in optically diverse ocean waters (0.07 to 25.35 mg/cu m range in surface chlorophyll a concentrations). The universality of the model was demonstrated by the accurate estimation of the spectral phytoplankton absorption coefficents over a range of 3 orders of magnitude (rho = 0.94 at 500 nm). Under most oceanic conditions (chlorophyll a less than 3 mg/cu m) the percent difference between measured and modeled phytoplankton absorption coefficents was less than 35%. Spectral variations in measured phytoplankton absorption spectra were well predicted by the inverse model. Modeled volume fluorescence was weakly correlated with measured chl a; fluorescence quantum yield varied from 0.008 to 0.09 as a function of environment and incident irradiance. Modeled particle backscattering coefficients were linearly related to total particle cross section over a twentyfold range in backscattering coefficents (rho = 0.996, n = 12).

Concentration and emission sources of airborne metals in particulate matter in the industrial district of Médio Paraíba, state of Rio de Janeiro, Brazil.

PubMed

Loyola, Josiane; de Almeida, Pierre Batista; Quiterio, Simone Lorena; Sousa, Célia Regina; Arbilla, Graciela; Escaleira, Viviane; de Carvalho, Maria Isabel; dos Santos Amaral Gomes da Silva, Alzira

2006-11-01

Total suspended particles and 12 airborne metals were determined in 4 sampling sites in the industrial region of Médio Paraíba, Brazil. The geometrical means for the four sampling locals were (in units of microg/m3): 65.9 in Barra Mansa, 57.3 in Jardim Paraíba (Volta Redonda), 41.7 in Resende, and 48.9 in Volta Grande (Volta Redonda). These values are lower than levels previously determined in urban and industrial locals of the Metropolitan Area of Rio de Janeiro. For metals, the higher concentrations were obtained for Ca, Zn, Al, Fe, and Mg. Ca, Zn, and Al levels are higher than those determined in other industrial areas. These three metals are used in steel manufacturing, the main economical activity of the region. Enrichment factors for Zn, Cu, Cd, and Pb are higher than 10, suggesting an industrial input. Statistical analysis show a high correlation among Ca, Mg, Zn, Cr, Al, Mn, and Fe, all of them used as raw materials in steel manufacturing and/or accumulated as industrial blast furnace slag and steelworks slag.

Phosphorus retention in a newly constructed wetland receiving agricultural tile drainage water.

PubMed

Kynkäänniemi, Pia; Ulén, Barbro; Torstensson, Gunnar; Tonderski, Karin S

2013-01-01

One measure used in Sweden to mitigate eutrophication of waters is the construction of small wetlands (free water surface wetland for phosphorus retention [P wetlands]) to trap particulate phosphorus (PP) transported in ditches and streams. This study evaluated P retention dynamics in a newly constructed P wetland serving a 26-ha agricultural catchment with clay soil. Flow-proportional composite water samples were collected at the wetland inlet and outlet over 2 yr (2010-2011) and analyzed for total P (TP), dissolved P (DP), particulate P (PP), and total suspended solids (TSS). Both winters had unusually long periods of snow accumulation, and additional time-proportional water samples were frequently collected during snowmelt. Inflow TP and DP concentrations varied greatly (0.02-1.09 mg L) during the sampling period. During snowmelt in 2010, there was a daily oscillation in P concentration and water flow in line with air temperature variations. Outflow P concentrations were generally lower than inflow concentrations, with net P losses observed only in August and December 2010. On an annual basis, the wetland acted as a net P sink, with mean specific retention of 69 kg TP, 17 kg DP, and 30 t TSS ha yr, corresponding to a reduction in losses of 0.22 kg TP ha yr from the agricultural catchment. Relative retention was high (36% TP, 9% DP, and 36% TSS), indicating that small constructed wetlands (0.3% of catchment area) can substantially reduce P loads from agricultural clay soils with moderately undulating topography. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Developing a semi-analytical algorithm to estimate particulate organic carbon (POC) levels in inland eutrophic turbid water based on MERIS images: A case study of Lake Taihu

NASA Astrophysics Data System (ADS)

Lyu, Heng; Wang, Yannan; Jin, Qi; Shi, Lei; Li, Yunmei; Wang, Qiao

2017-10-01

Particulate organic carbon (POC) plays an important role in the carbon cycle in water due to its biological pump process. In the open ocean, algorithms can accurately estimate the surface POC concentration. However, no suitable POC-estimation algorithm based on MERIS bands is available for inland turbid eutrophic water. A total of 228 field samples were collected from Lake Taihu in different seasons between 2013 and 2015. At each site, the optical parameters and water quality were analyzed. Using in situ data, it was found that POC-estimation algorithms developed for the open ocean and coastal waters using remote sensing reflectance were not suitable for inland turbid eutrophic water. The organic suspended matter (OSM) concentration was found to be the best indicator of the POC concentration, and POC has an exponential relationship with the OSM concentration. Through an analysis of the POC concentration and optical parameters, it was found that the absorption peak of total suspended matter (TSM) at 665 nm was the optimum parameter to estimate POC. As a result, MERIS band 7, MERIS band 10 and MERIS band 12 were used to derive the absorption coefficient of TSM at 665 nm, and then, a semi-analytical algorithm was used to estimate the POC concentration for inland turbid eutrophic water. An accuracy assessment showed that the developed semi-analytical algorithm could be successfully applied with a MAPE of 31.82% and RMSE of 2.68 mg/L. The developed algorithm was successfully applied to a MERIS image, and two full-resolution MERIS images, acquired on August 13, 2010, and December 7, 2010, were used to map the POC spatial distribution in Lake Taihu in summer and winter.

Communal biofuel burning for district heating: Emissions and immissions from medium-sized (0.4 and 1.5 MW) facilities

NASA Astrophysics Data System (ADS)

Fachinger, Friederike; Drewnick, Frank; Gieré, Reto; Borrmann, Stephan

2018-05-01

Particulate and gaseous emissions of two medium-sized district heating facilities (400 kW, fueled with miscanthus, and 1.5 MW, fueled with wood chips) were characterized for different operational conditions, and compared to previously obtained results for household wood and pellet stoves. SO2 and NOx emission factors (reported in mg MJFuel-1) were found to not only depend on fuel sulfur/nitrogen content, but also on combustion appliance type and efficiency. Emission factors of SO2, NOx, and PM (particulate matter) increased with increasing load. Particle chemical composition did not primarily depend on operational conditions, but varied mostly with combustion appliances, fuel types, and flue gas cleaning technologies. Black carbon content was decreasing with increasing combustion efficiency; chloride content was strongly enhanced when burning miscanthus. Flue gas cleaning using an electrostatic precipitator caused strong reduction not only in total PM, but also in the fraction of refractory and semi-refractory material within emitted PM1. For the impact of facilities on their surroundings (immissions) not only their total emissions are decisive, but also their stack heights. In immission measurements downwind of the two facilities, a plume could only be observed for the 400 kW facility with low (11 m) stack height (1.5 MW facility: 30 m), and measured immissions agreed reasonably well with predicted ones. The impact of these immissions is non-negligible: At a distance of 50 m from the facility, apart from CO2, also plume contributions of NOx, ultrafine particles, PM1, PM10, poly-aromatic hydrocarbons, and sulfate were detected, with enhancements above background values of 2-130%.

Source apportionment and toxicity of atmospheric polycyclic aromatic hydrocarbons by PMF: Quantifying the influence of coal usage in Taiyuan, China

NASA Astrophysics Data System (ADS)

Yan, Yulong; He, Qiusheng; Guo, Lili; Li, Hongyan; Zhang, Hefeng; Shao, Min; Wang, Yuhang

2017-09-01

Atmospheric polycyclic aromatic hydrocarbons (PAHs) were analyzed in the gas phase and total suspended particulate (TSP) from summer 2014 to spring 2015 in Taiyuan, northern China. Taiyuan is an area with some of the highest atmospheric PAH levels in the world, and the total PAHs was highest in winter, followed by autumn, spring and summer. Low air temperature and a southern wind with low speed often led to higher PAH levels in Taiyuan. Although less than a half fraction, the benzo[a]pyrene equivalent concentration (BEQ) of particulate PAHs was almost equal to that of the total PAHs. Four sources, coal combustion, vehicle emissions, coke processing and biomass burning, were determined by positive matrix factorization (PMF), with contributions of 41.36%, 24.74%, 19.71% and 14.18% to the total PAHs in Taiyuan, respectively. Compared with the total PAHs, the particulate PAH solution underestimated the contribution of the coke processing, especially in winter, and overestimated vehicle emissions. The coke processing had a greater contribution to atmospheric PAHs with a southern wind at low speeds in winter in Taiyuan. Ultimately, the coke plants distributed in the Taiyuan-Linfen-Yuncheng basin should receive greater attention for air quality improvement in Taiyuan.

Enhanced Particulate Organic Carbon Export at Eddy Edges in the Oligotrophic Western North Pacific Ocean

PubMed Central

Shih, Yung-Yen; Hung, Chin-Chang; Gong, Gwo-Ching; Chung, Wan-Chen; Wang, Yu-Huai; Lee, I-Huan; Chen, Kuo-Shu; Ho, Chuang-Yi

2015-01-01

Mesoscale eddies in the subtropical oligotrophic ocean are ubiquitous and play an important role in nutrient supply and oceanic primary production. However, it is still unclear whether these mesoscale eddies can efficiently transfer CO2 from the atmosphere to deep waters via biological pump because of the sampling difficulty due to their transient nature. In 2007, particulate organic carbon (POC) fluxes, measured below the euphotic zone at the edge of warm eddy were 136–194 mg-C m−2 d−1 which was greatly elevated over that (POC flux = 26–35 mg-C m−2 d−1) determined in the nutrient-depleted oligotrophic waters in the Western North Pacific (WNP). In 2010, higher POC fluxes (83–115 mg-C m−2 d−1) were also observed at the boundary of mesoscale eddies in the WNP. The enhanced POC flux at the edge of eddies was mainly attributed to both large denuded diatom frustules and zooplankton fecal pellets based on scanning electron microscopy (SEM) examination. The result suggests that mesoscale eddies in the oligotrophic waters in the subtropical WNP can efficiently increase the oceanic carbon export flux and the eddy edge is a crucial conduit in carbon sequestration to deep waters. PMID:26171611

Characteristics of particle-bound polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in atmosphere used in carbon black feeding process at a tire manufacturing plant.

PubMed

Chuang, Kuen-Yuan; Lai, Chia-Hsiang; Peng, Yen-Ping; Yen, Ting-Yu

2015-12-01

Concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were estimated for different particle size distributions in a carbon black feeding process at a tire manufacturing plant on 15 days in March and April of 2014. A total of 75 integrated air samples were collected using a micro-orifice uniform deposition impactor (MOUDI). Particle-bound PCDD/Fs were analyzed using a high-resolution gas chromatograph/high-resolution mass spectrometer (HRGC/HRMS). Concentrations of thoracic particles and total particles produced in the carbon black feeding process of a tire manufacturing plant were measured in ranges of 0.19-2.61 and 0.28-4.22 mg/m(3), respectively. On all sampling days, the three most abundant species of PCDD/Fs were OCDD, 1,2,3,4,6,7,8-HpCDF, and OCDF. The mean concentrations of total PCDD/Fs were 0.74-6.83 pg/m(3) within five particle size ranges. Total I-TEQ in particulate matter (PM)<1.0 was 2.2 and 3.2 times higher than those in PM>18 and PM2.5-10, respectively. However, the total I-TEQ of thoracic PM contributed approximately 74 % of the total I-TEQ of total PM. The assessment of health risk indicates that exposure to fractions of thoracic PM by inhalation poses a significant cancer risk (>10(-6)).

[Chemical Compositions and Sources Apportionment of Re-suspended Dust in Jincheng].

PubMed

Wang, Yan; Peng, Lin; Li, Li-juan; Zhang, Teng; Liu, Hai-li; Mu, Ling

2016-01-15

In order to make effective plan to provide the scientific basis for prevention and control of re-suspended dust (RD), samples of particulate sources including RD and other pollution sources of Jincheng were collected. Elements, ions and carbon in particulate sources were analyzed. Enrichment factor, potential ecological risk assessment, and chemical mass balance model were used to analyze the chemical composition and the source of RD. The result indicated that the main components in RD of Jingeheng were Si, TC, Ca, OC, Al, Mg, Na, Fe, K and SO4(2-), contributing 61.14% of total mass of RD. The most abundant content of RD was crustal elements, and the ions were enriched in the fine particles. The mass fraction of OC in PM2. was higher, whereas the mass fraction of EC in PM10 was higher, indicating that secondary organic pollutants were mainly dominated in the fine particles. The dust PM2.5 and PM10 potential ecological risk indexes were extremely strong, and PM2.5 had higher ecological harm than PM10. Pb had the highest enrichment factor of 196.97 in PM2.5, which was followed by As, Cr, Ni, V, Zn and Cu, the enrichment factors of which were all greater than 10, indicating that they were apparently enriched and affected by human activities. Soil dust, construction dust, vehicle exhaust, and coal dust were the main sources of RD.

Downstream processing of reverse osmosis brine: Characterisation of potential scaling compounds.

PubMed

Zaman, Masuduz; Birkett, Greg; Pratt, Christopher; Stuart, Bruce; Pratt, Steven

2015-09-01

Reverse osmosis (RO) brine produced at a full-scale coal seam gas (CSG) water treatment facility was characterized with spectroscopic and other analytical techniques. A number of potential scalants including silica, calcium, magnesium, sulphates and carbonates, all of which were present in dissolved and non-dissolved forms, were characterized. The presence of spherical particles with a size range of 10-1000 nm and aggregates of 1-10 microns was confirmed by transmission electron microscopy (TEM). Those particulates contained the following metals in decreasing order: K, Si, Sr, Ca, B, Ba, Mg, P, and S. Characterization showed that nearly one-third of the total silicon in the brine was present in the particulates. Further, analysis of the RO brine suggested supersaturation and precipitation of metal carbonates and sulphates during the RO process should take place and could be responsible for subsequently capturing silica in the solid phase. However, the precipitation of crystalline carbonates and sulphates are complex. X-ray diffraction analysis did not confirm the presence of common calcium carbonates or sulphates but instead showed the presence of a suite of complex minerals, to which amorphous silica and/or silica rich compounds could have adhered. A filtration study showed that majority of the siliceous particles were less than 220 nm in size, but could still be potentially captured using a low molecular weight ultrafiltration membrane. Copyright © 2015 Elsevier Ltd. All rights reserved.

40 CFR 60.424 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Ammonium Sulfate.../ton) of ammonium sulfate produced. cs = concentration of particulate matter, g/dscm (g/dscf). Qsd = volumetric flow rate of effluent gas, dscm/hr (dscf/hr). P = production rate of ammonium sulfate, Mg/hr (ton...

40 CFR 60.404 - Test methods and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Phosphate Rock.../ton) of phosphate rock feed. cs=concentration of particulate matter, g/dscm (g/dscf). Qsd=volumetric flow rate of effluent gas, dscm/hr (dscf/hr). P=phosphate rock feed rate, Mg/hr (ton/hr). K=conversion...

40 CFR 60.404 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Phosphate Rock.../ton) of phosphate rock feed. cs = concentration of particulate matter, g/dscm (g/dscf). Qsd = volumetric flow rate of effluent gas, dscm/hr (dscf/hr). P=phosphate rock feed rate, Mg/hr (ton/hr). K...

40 CFR 60.404 - Test methods and procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Phosphate Rock.../ton) of phosphate rock feed. cs=concentration of particulate matter, g/dscm (g/dscf). Qsd=volumetric flow rate of effluent gas, dscm/hr (dscf/hr). P=phosphate rock feed rate, Mg/hr (ton/hr). K=conversion...

40 CFR 60.404 - Test methods and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Phosphate Rock.../ton) of phosphate rock feed. cs=concentration of particulate matter, g/dscm (g/dscf). Qsd=volumetric flow rate of effluent gas, dscm/hr (dscf/hr). P=phosphate rock feed rate, Mg/hr (ton/hr). K=conversion...

40 CFR 60.404 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Phosphate Rock.../ton) of phosphate rock feed. cs=concentration of particulate matter, g/dscm (g/dscf). Qsd=volumetric flow rate of effluent gas, dscm/hr (dscf/hr). P=phosphate rock feed rate, Mg/hr (ton/hr). K=conversion...

Flocculent Settling of Food Wastes.

PubMed

Chowdhury, Mohammad Monirul Islam; Kim, Mingu; Haroun, Basem Mikhaeil; Nakhla, George; Keleman, Michael

2016-07-01

This study evaluated the flocculent settling in water and municipal wastewater (MWW) in a 10.6 ft deep column. A total of eight runs at three different testing conditions involving MWW alone, food waste (FW) alone, and FW in MWW (FW+MWW) were conducted. Total suspended solid (TSS), total BOD (TBOD), total COD (TCOD), total nitrogen (TN), and total phosphorous (TP) removal efficiencies after 3 hours of settling were 62%, 46%, 49%, 46% and 62% for FW, and 50%, 43%, 39%, 37% and 24% for MWW. Removal efficiencies of particulate COD (PCOD) and particulate BOD (PBOD) at the lowest surface overflow rate (SOR) of 1.1 m3/m2/hr corresponding to the longest settling time of 3 hours were 59% and 64% for FW, and 65% and 70% for FW with MWW samples. On the other hand, no significant variation between FW and FW with MWW was observed for PN removal after 3 hours of settling.

Production of all trans-beta-carotene by using impinging flow of supercritical carbon dioxide anti-solvent pulverization.

PubMed

Shen, Yi-Chen; Chng, Lee-Muei; Wang, Yuan-Chuen; Shieh, Chwen-Jen; Lin, Kuo-Li; Hsu, Shih-Lan; Chou, Hong-Nong; Chang, Chieh-Ming J

2012-12-28

This work investigated column elution chromatography coupled with supercritical anti-solvent precipitation to produce carotenoid rich microsized particulates from microalgal Dunaliella salina species. The extract contained carotenoids ranging from 61.3 mg/g(salina) to 72.5 mg/g(salina) using ultrasonic stirred ethyl ether or tetrahydrofuran (THF) extraction. When 10 L of ethyl alcohol was employed to elute the THF extract, purity of trans-β-carotene is 823.6 mg/g with a recovery of 86.2%. It was found that the supercritical anti-solvent of THF solution at 160 bar and 318 K produced powdered particulates with a purity of carotenoids above 90%. Subsequently, a central composite response surface design method was used to design supercritical anti-solvent precipitation of carotenoid-rich THF solution. This was accomplished by increasing the pressure from 140 bar to 180 bar and the time from 40 min to 60 min at a feed flow rate of 0.2 mL/min. A CO(2) flow rate of 15 L/min and a temperature of 318 K were also used to determine the effects on purity and recovery of trans-β-carotene. The combined process produced micronized precipitates with a mean particle size ranging from 3.5 μm to 19 μm and the purity of trans-β-carotene attained was 926.8 mg/g with a recovery of 54%. Copyright © 2012 Elsevier B.V. All rights reserved.

Estimation of phosphorus flux in rivers during flooding.

PubMed

Chen, Yen-Chang; Liu, Jih-Hung; Kuo, Jan-Tai; Lin, Cheng-Fang

2013-07-01

Reservoirs in Taiwan are inundated with nutrients that result in algal growth, and thus also reservoir eutrophication. Controlling the phosphorus load has always been the most crucial issue for maintaining reservoir water quality. Numerous agricultural activities, especially the production of tea in riparian areas, are conducted in watersheds in Taiwan. Nutrients from such activities, including phosphorus, are typically flushed into rivers during flooding, when over 90% of the yearly total amount of phosphorous enters reservoirs. Excessive or enhanced soil erosion from rainstorms can dramatically increase the river sediment load and the amount of particulate phosphorus flushed into rivers. When flow rates are high, particulate phosphorus is the dominant form of phosphorus, but sediment and discharge measurements are difficult during flooding, which makes estimating phosphorus flux in rivers difficult. This study determines total amounts of phosphorus transport by measuring flood discharge and phosphorous levels during flooding. Changes in particulate phosphorus, dissolved phosphorus, and their adsorption behavior during a 24-h period are analyzed owing to the fact that the time for particulate phosphorus adsorption and desorption approaching equilibrium is about 16 h. Erosion of the reservoir watershed was caused by adsorption and desorption of suspended solids in the river, a process which can be summarily described using the Lagmuir isotherm. A method for estimating the phosphorus flux in the Daiyujay Creek during Typhoon Bilis in 2006 is presented in this study. Both sediment and phosphorus are affected by the drastic discharge during flooding. Water quality data were collected during two flood events, flood in June 9, 2006 and Typhoon Bilis, to show the concentrations of suspended solids and total phosphorus during floods are much higher than normal stages. Therefore, the drastic changes of total phosphorus, particulate phosphorus, and dissolved phosphorus in rivers during flooding should be monitored to evaluate the loading of phosphorus more precisely. The results show that monitoring and controlling phosphorus transport during flooding can help prevent the eutrophication of a reservoir.

Decadal-scale export of nitrogen, phosphorus, and sediment from the Susquehanna River basin, USA: Analysis and synthesis of temporal and spatial patterns

USGS Publications Warehouse

Zhang, Qian; Ball, William P.; Moyer, Douglas

2016-01-01

The export of nitrogen (N), phosphorus (P), and suspended sediment (SS) is a long-standing management concern for the Chesapeake Bay watershed, USA. Here we present a comprehensive evaluation of nutrient and sediment loads over the last three decades at multiple locations in the Susquehanna River basin (SRB), Chesapeake's largest tributary watershed. Sediment and nutrient riverine loadings, including both dissolved and particulate fractions, have generally declined at all sites upstream of Conowingo Dam (non-tidal SRB outlet). Period-of-record declines in riverine yield are generally smaller than those in source input, suggesting the possibility of legacy contributions. Consistent with other watershed studies, these results reinforce the importance of considering lag time between the implementation of management actions and achievement of river quality improvement. Whereas flow-normalized loadings for particulate species have increased recently below Conowingo Reservoir, those for upstream sites have declined, thus substantiating conclusions from prior studies about decreased reservoir trapping efficiency. In regard to streamflow effects, statistically significant log-linear relationships between annual streamflow and annual constituent load suggest the dominance of hydrological control on the inter-annual variability of constituent export. Concentration-discharge relationships revealed general chemostasis and mobilization effects for dissolved and particulate species, respectively, both suggesting transport-limitation conditions. In addition to affecting annual export rates, streamflow has also modulated the relative importance of dissolved and particulate fractions, as reflected by its negative correlations with dissolved P/total P, dissolved N/total N, particulate P/SS, and total N/total P ratios. For land-use effects, period-of-record median annual yields of N, P, and SS all correlate positively with the area fraction of non-forested land but negatively with that of forested land under all hydrological conditions. Overall, this work has informed understanding with respect to four major factors affecting constituent export (i.e., source input, reservoir modulation, streamflow, and land use) and demonstrated the value of long-term river monitoring.

Settling Efficiency of Urban Particulate Matter Transported by Stormwater Runoff.

PubMed

Carbone, Marco; Penna, Nadia; Piro, Patrizia

2015-09-01

The main purpose of control measures in urban areas is to retain particulate matter washed out by stormwater over impermeable surfaces. In stormwater control measures, particulate matter removal typically occurs via sedimentation. Settling column tests were performed to examine the settling efficiency of such units using monodisperse and heterodisperse particulate matter (for which the particle size distributions were measured and modelled by the cumulative gamma distribution). To investigate the dependence of settling efficiency from the particulate matter, a variant of the evolutionary polynomial regression (EPR), a Microsoft Excel function based on multi-objective EPR technique (EPR-MOGA), called EPR MOGA XL, was used as a data-mining strategy. The results from this study have shown that settling efficiency is a function of the initial total suspended solids (TSS) concentration and of the median diameter (d50 index), obtained from the particle size distributions (PSDs) of the samples.

Evaluating Students' Conceptual Understanding of Balanced Equations and Stoichiometric Ratios Using a Particulate Drawing

ERIC Educational Resources Information Center

Sanger, Michael J.

2005-01-01

A total of 156 students were asked to provide free-response balanced chemical equations for a classic multiple-choice particulate-drawing question first used by Nurrenbern and Pickering. The balanced equations and the number of students providing each equation are reported in this study. The most common student errors included a confusion between…

An initial investigation into the organic matter biogeochemistry of the Congo River

USGS Publications Warehouse

Spencer, Robert G.M.; Hernes, Peter J.; Aufdenkampe, Anthony K.; Baker, Andy; Gulliver, Pauline; Stubbins, Aron; Aiken, George R.; Dyda, Rachael Y.; Butler, Kenna D.; Mwamba, Vincent L.; Mangangu, Arthur M.; Wabakanghanzi, Jose N.; Six, Johan

2012-01-01

The Congo River, which drains pristine tropical forest and savannah and is the second largest exporter of terrestrial carbon to the ocean, was sampled in early 2008 to investigate organic matter (OM) dynamics in this historically understudied river basin. We examined the elemental (%OC, %N, C:N), isotopic (δ13C, Δ14C, δ15N) and biochemical composition (lignin phenols) of coarse particulate (>63 μm; CPOM) and fine particulate (0.7–63 μm; FPOM) OM and DOC, δ13C, Δ14C and lignin phenol composition with respect to dissolved OM (14C = -62.2 ± -13.2‰, n = 5) compared to CPOM and DOM (mean Δ14C = 55.7 ± 30.6‰, n = 4 and 73.4 ± 16.1‰, n = 5 respectively). The modern radiocarbon ages for DOM belie a degraded lignin compositional signature (i.e. elevated acid:aldehyde ratios (Ad:Al) relative to CPOM and FPOM), and indicate that the application of OM degradation patterns derived from particulate phase studies to dissolved samples needs to be reassessed: these elevated ratios are likely attributable to fractionation processes during solubilization of plant material. The relatively low DOM carbon-normalized lignin yields (Λ8; 0.67–1.12 (mg(100 mg OC)-1)) could also reflect fractionation processes, however, they have also been interpreted as an indication of significant microbial or algal sources of DOM. CPOM appears to be well preserved higher vascular plant material as evidenced by its modern radiocarbon age, elevated C:N (17.2–27.1) and Λ8 values (4.56–7.59 (mg(100 mg OC)-1)). In relation to CPOM, the aged FPOM fraction (320–580 ybp 14C ages) was comparatively degraded, as demonstrated by its nitrogen enrichment (C:N 11.4–14.3), lower Λ8 (2.80–4.31 (mg(100 mg OC)-1)) and elevated lignin Ad:Al values similar to soil derived OM. In this study we observed little modification of the OM signature from sample sites near the cities of Brazzaville and Kinshasa to the head of the estuary (~350 km) highlighting the potential for future studies to assess seasonal and long-term OM dynamics from this logistically feasible location and derive relevant information with respect to OM exported to the Atlantic Ocean. The relative lack of OM data for the Congo River Basin highlights the importance of studies such as this for establishing baselines upon which to gauge future change.

Phosphorus transfer in runoff following application of fertilizer, manure, and sewage sludge.

PubMed

Withers, P J; Clay, S D; Breeze, V G

2001-01-01

Phosphorus (P) transfer in surface runoff from field plots receiving either no P, triplesuperphoshate (TSP), liquid cattle manure (LCS), liquid anaerobically digested sludge (LDS), or dewatered sludge cake (DSC) was compared over a 2-yr period. Dissolved inorganic P concentrations in runoff increased from 0.1 to 0.2 mg L(-1) on control and sludge-treated plots to 3.8 and 6.5 mg L(-1) following application of LCS and TSP, respectively, to a cereal crop in spring. When incorporated into the soil in autumn, runoff dissolved P concentrations were typically < 0.5 mg L(-1) across all plots, and particulate P remained the dominant P form. When surface-applied in autumn to a consolidated seedbed, direct loss of LCS and LDS increased both runoff volume and P transfers, but release of dissolved P occurred only from LCS. The largest P concentrations (>70 mg L(-1)) were recorded following TSP application without any increase in runoff volume, while application of bulky DSC significantly reduced total P transfers by 70% compared with the control due to a reduced runoff volume. Treatment effects in each monitoring period were most pronounced in the first runoff event. Differences in the release of P from the different P sources were related to the amounts of P extracted by either water or sodium bicarbonate in the order TSP > LCS > LDS > DSC. The results suggest there is a lower risk of P transfer in land runoff following application of sludge compared with other agricultural P amendments at similar P rates.

Consumption-based Total Suspended Particulate Matter Emissions in Jing-Jin-Ji Area of China

NASA Astrophysics Data System (ADS)

Yang, S.; Chen, S.; Chen, B.

2014-12-01

The highly-industrialized regions in China have been facing a serious problem of haze mainly consisted of total suspended particulate matter (TSPM), which has attracted great attention from the public since it directly impairs human health and clinically increases the risks of various respiratory and pulmonary diseases. In this paper, we set up a multi-regional input-output (MRIO) model to analyze the transferring routes of TSPM emissions between regions through trades. TSPM emission from particulate source regions and sectors are identified by analyzing the embodied TSPM flows through monetary flow and carbon footprint. The track of TSPM from origin to end via consumption activities are also revealed by tracing the product supply chain associated with the TSPM emissions. Beijing-Tianjin-Hebei (Jing-Jin-Ji) as the most industrialized area of China is selected for a case study. The result shows that over 70% of TSPM emissions associated with goods consumed in Beijing and Tianjin occurred outside of their own administrative boundaries, implying that Beijing and Tianjin are net embodied TSPM importers. Meanwhile, 63% of the total TSPM emissions in Hebei Province are resulted from the outside demand, indicating Hebei is a net exporter. In addition, nearly half of TSPM emissions are the by-products related to electricity and heating supply and non-metal mineral products in Jing-Jin-Ji Area. Based on the model results, we provided new insights into establishing systemic strategies and identifying mitigation priorities to stem TSPM emissions in China. Keywords: total suspended particulate matter (TSPM); urban ecosystem modeling; multi-regional input-output (MRIO); China

Microscopic and submicron components of atmospheric particulate matter during high asthma periods in Brisbane, Queensland, Australia

NASA Astrophysics Data System (ADS)

Glikson, M.; Rutherford, S.; Simpson, R. W.; Mitchell, C. A.; Yago, A.

The study identifies the various components contributing to atmospheric particulate matter in Brisbane, Queensland, Australia, during the period from the end of April and the months of July-August in 1992, covering the autumn period which is typically the period of high asthma incidence in Brisbane. Most particulate matter is < 2 μm and submicronic. Electron microscopy revealed that the submicron material is composed mainly of combusted ("soot") and incompletely burned hydrocarbons arising from motor vehicle exhaust emissions, crustal matter in the form of quartz microconcretions and other silicates, quiescent spores of Mucorales, and soil bacteria. The contribution from pollen and fungal spores has been evaluated and quantified. Fungal spores counts dominate the bioaerosol counts in the 2-10 μm range and are very high in Brisbane from the end of April through May to mid-June. However even at peak periods the total bioaerosol count only contributes of the order of 5-10% of the total particulate mass. The results show that Pm 10 (particulate matter less than 10 μm in diameter) and nephelometer readings do not indicate peak periods of allergenic bioaerosol readings (in fact there is a negative correlation) due to the low contribution of the bioaerosol count to the total and the different influences of wind speed. However the electron microscopy results show that this does not mean there are no synergies between aerosols from anthropogenic sources and bioaerosols. The cytoplasmic content of spores and pollen was often found to be adhered to motor vehicle emission material and crustal matter. The latter may therefore act as carriers for dispersed cytoplasmic allergenic material released from pollen and fungal spores.

Distribution, origin and transformation of amino sugars and bacterial contribution to estuarine particulate organic matter

NASA Astrophysics Data System (ADS)

Khodse, Vishwas B.; Bhosle, Narayan B.

2013-10-01

Amino sugars including bacterial biomarker muramic acid (Mur) were investigated in suspended particulate matter (SPM) to understand their distribution, origin, and biogeochemical cycling and the contribution of bacteria to particulate organic matter (POM) of the Mandovi estuary. SPM was collected from 9 sampling stations in the Mandovi estuary during the pre-monsoon (March) and monsoon (August). Total particulate amino sugar (TPAS) concentrations and yields varied spatially and were 2 to 5 times higher during the monsoon than the pre-monsoon. Negative correlation between salinity and TPAS-C yields [TPAS-C/particulate organic carbon (POC)×100] indicates the influence of terrestrial organic matter on the transport of TPAS-carbon. Glucosamine (GlcN), galactosamine (GalN), and mannosamine (ManN) were abundant during the monsoon. Low GlcN/GalN ratios (<3) indicate bacteria as the major source of amino sugars. Higher amino sugar yields and lower GlcN/GalN ratios during the monsoon than the pre-monsoon indicate enhanced transformation and greater bacterial contribution to POM during the former season. Degradation trends observed with TPAS were well supported by those obtained with carbohydrates and amino acids. Based on Mur concentrations, bacteria accounted for 24% to 35% of the POC and 24% to 62% of the total particulate nitrogen (TPN). Intact bacterial cells, however accounted for a small proportion of POC (2.5% to 4%) and TPN (9% to 11%). Our study suggests that POM was subjected to extensive diagenetic transformation, and its composition was influenced by bacteria, especially during the monsoon.

Genotoxic substances in the St. Lawrence system. 1: Industrial genotoxins sorbed to particulate matter in the St. Lawrence, St. Maurice, and Saguenay rivers, Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, P.A.; Rasmussen, J.B.; Blaise, C.

1998-02-01

Previous investigations of organic genotoxins in industrial effluents discharged into the St. Lawrence River system (Quebec, Canada) indicated that a substantial fraction of the genotoxicity is adsorbed to suspended particulate matter. This study used the SOS Chromotest to investigate the presence, potency, and behavior of particle-bound genotoxins in the downstream ecosystem. The results indicate that although extracts of both suspended and sedimented particulate matter are genotoxic, suspended particulate matter samples are more potent in the absence of S9 activation, with the reverse being true for bottom sediments. The results confirmed a positive relationship between the genotoxicity of bottom sediment extractsmore » and sediment organic matter content. A similar relationship between organic matter content and total polycyclic aromatic hydrocarbon (PAH) concentration indicates that putative genotoxins have physicochemical properties similar to the PAH class of contaminants. Conversion of PAH values to benzo[a]pyrene equivalents indicates that measured PAHs only account for a small fraction ({approximately}10%) of the observed SOS Chromotest response. Sites that receive discharges from foundries, aluminum refineries, and petroleum refineries yielded several of the most genotoxic samples. Further analyses revealed that the genotoxicity of suspended and sedimented particulate matter extracts is empirically related to the genotoxicity of industrial discharges. Comparisons of total genotoxicity levels in suspended particulates and bottom sediments suggest that direct-acting substances adsorbed to suspended matter are rapidly degraded and/or converted to more stable progenotoxins upon deposition. Further research is required to test this hypothesis and investigate effects on indigenous biota.« less

Gasoline Particulate Filters as an Effective Tool to Reduce Particulate and Polycyclic Aromatic Hydrocarbon Emissions from Gasoline Direct Injection (GDI) Vehicles: A Case Study with Two GDI Vehicles.

PubMed

Yang, Jiacheng; Roth, Patrick; Durbin, Thomas D; Johnson, Kent C; Cocker, David R; Asa-Awuku, Akua; Brezny, Rasto; Geller, Michael; Karavalakis, Georgios

2018-03-06

We assessed the gaseous, particulate, and genotoxic pollutants from two current technology gasoline direct injection vehicles when tested in their original configuration and with a catalyzed gasoline particulate filter (GPF). Testing was conducted over the LA92 and US06 Supplemental Federal Test Procedure (US06) driving cycles on typical California E10 fuel. The use of a GPF did not show any fuel economy and carbon dioxide (CO 2 ) emission penalties, while the emissions of total hydrocarbons (THC), carbon monoxide (CO), and nitrogen oxides (NOx) were generally reduced. Our results showed dramatic reductions in particulate matter (PM) mass, black carbon, and total and solid particle number emissions with the use of GPFs for both vehicles over the LA92 and US06 cycles. Particle size distributions were primarily bimodal in nature, with accumulation mode particles dominating the distribution profile and their concentrations being higher during the cold-start period of the cycle. Polycyclic aromatic hydrocarbons (PAHs) and nitrated PAHs were quantified in both the vapor and particle phases of the PM, with the GPF-equipped vehicles practically eliminating most of these species in the exhaust. For the stock vehicles, 2-3 ring compounds and heavier 5-6 ring compounds were observed in the PM, whereas the vapor phase was dominated mostly by 2-3 ring aromatic compounds.

Direct ultrasonic agitation for rapid extraction of organic matter from airborne particulate.

PubMed

Lee, S C; Zou, S C; Ho, K F; Chan, L Y

2001-01-02

Direct ultrasonic extraction (DUE) is proposed as simple and rapid sample pretreatment method. This new approach is applied to the extraction of particulate organic matter (POM) from airborne particulate by using dichloromethane (DCM) or DCM/methanol (90/10, v/v) as extractant. The analytical determination was carried out by weighing the extractable POM on an electrobalance. Total recovery for POM could be obtained when the sample was extracted three times with 25-50 mL extractant each for about 5 min at 50 W ultrasonic power. In comparison with conventional Soxhlet extraction, less extraction time (total 15 min only) and solvent consumption (100 mL) were required by DUE. The efficiency of the DUE was similar or even higher than the routine Soxhlet method. Additionally, the new extractor is very simple and easy to use and can accelerate the extraction procedures of organic components from various solid samples.

Performance of a Retrofitted Multicyclone for PM2.5 Emission Control

NASA Astrophysics Data System (ADS)

Dewika, M.; Rashid, M.; Ammar, M. R.

2018-03-01

This paper presents on the performance of a retrofitted multicyclone system, which aims to increase the collection efficiency of PM2.5 (i.e. particulate size fraction ≤ 2.5 μm) emission. The multicyclone was retrofitted by extracting 15% and 20% of the total volumetric air flow rate at the dust hopper of the unit using an additional Induced Draft Fan. The total collection efficiency with and without the extraction was measured at various air volumetric flow rates and particulate mass inlet concentration. The results showed that there was a reduction of 12% to 54% depending on the inlet concentration of PM2.5 emission in the stack with compared to without extraction increasing the collection efficiency of the retrofitted multicyclone. The finding suggests that a simple technique of applying gas extraction at the dust hopper of a multicyclone as reported in this study able to increase the overall performance in fine particulate collection.

Transport of particle-associated elements in two agriculture-dominated boreal river systems.

PubMed

Marttila, Hannu; Saarinen, Tuomas; Celebi, Ahmet; Kløve, Bjørn

2013-09-01

Transport of particulate pollutants in fluvial systems can contribute greatly to total loads. Understanding transport mechanics under different hydrological conditions is key in successful load estimation. This study analysed trace elements and physico-chemical parameters in time-integrated suspended sediment samples, together with dissolved and total concentrations of pollutants, along two agriculture- and peatland-dominated boreal river systems. The samples were taken in a spatially and temporally comprehensive sampling programme during the ice-free seasons of 2010 and 2011. The hydrochemistry and transport of particle-bound elements in the rivers were strongly linked to intense land use and acid sulphate soils in the catchment area, with arable, pasture and peat areas in particular being main diffuse sources. There were significant seasonal and temporal variations in dissolved and particulate fluxes, but spatial variations were small. Continuous measurements of EC, turbidity and discharge proved to be an accurate indicator of dissolved and particulate fluxes. Overall, the results show that transport of particle-bound elements makes a major contribution to total transport fluxes in agriculture-dominated boreal rivers. Copyright © 2013 Elsevier B.V. All rights reserved.

Estimation of particulate nutrient load using turbidity meter.

PubMed

Yamamoto, K; Suetsugi, T

2006-01-01

The "Nutrient Load Hysteresis Coefficient" was proposed to evaluate the hysteresis of the nutrient loads to flow rate quantitatively. This could classify the runoff patterns of nutrient load into 15 patterns. Linear relationships between the turbidity and the concentrations of particulate nutrients were observed. It was clarified that the linearity was caused by the influence of the particle size on turbidity output and accumulation of nutrients on smaller particles (diameter < 23 microm). The L-Q-Turb method, which is a new method for the estimation of runoff loads of nutrients using a regression curve between the turbidity and the concentrations of particulate nutrients, was developed. This method could raise the precision of the estimation of nutrient loads even if they had strong hysteresis to flow rate. For example, as for the runoff load of total phosphorus load on flood events in a total of eight cases, the averaged error of estimation of total phosphorus load by the L-Q-Turb method was 11%, whereas the averaged estimation error by the regression curve between flow rate and nutrient load was 28%.

Anaerobic digestibility of marine microalgae Phaeodactylum tricornutum in a lab-scale anaerobic membrane bioreactor.

PubMed

Zamalloa, Carlos; De Vrieze, Jo; Boon, Nico; Verstraete, Willy

2012-01-01

The biomass of industrially grown Phaeodactylum tricornutum was subjected in a novel way to bio-methanation at 33°C, i.e., in an anaerobic membrane bioreactor (AnMBR) at a hydraulic retention time of 2.5 days, at solid retention times of 20 to 10 days and at loading rates in the range of 2.6-5.9 g biomass-COD L(-1) day(-1) with membrane fluxes ranging from 1 to 0.8 L m(-2) h(-1). The total COD recovered as biogas was in the order of 52%. The input suspension was converted to a clear effluent rich in total ammonium nitrogen (546 mg TAN L(-1)) and phosphate (141 mg PO(4)-P L(-1)) usable as liquid fertilizer. The microbial community richness, dynamics, and organization in the reactor were interpreted using the microbial resource management approach. The AnMBR communities were found to be moderate in species richness and low in dynamics and community organization relative to UASB and conventional CSTR sludges. Quantitative polymerase chain reaction analysis revealed that Methanosaeta sp. was the dominant acetoclastic methanogen species followed by Methanosarcina sp. This work demonstrated that the use of AnMBR for the digestion of algal biomass is possible. The fact that some 50% of the organic matter is not liquefied means that the algal particulates in the digestate constitute a considerable fraction which should be valorized properly, for instance as slow release organic fertilizer. Overall, 1 kg of algae dry matter (DM) could be valorized in the form of biogas ( euro 2.07), N and P in the effluent (euro 0.02) and N and P in the digestate (euro 0.04), thus totaling about euro 2.13 per kilogram algae DM.

Contribution to a bio-optical model for remote sensing of Lena River water

NASA Astrophysics Data System (ADS)

Örek, H.; Doerffer, R.; Röttgers, R.; Boersma, M.; Wiltshire, K. H.

2013-11-01

Bio-optical measurements and sampling were carried out in the delta of the Lena River (northern Siberia, Russia) between 26 June and 4 July 2011. The aim of this study was to determine the inherent optical properties of the Lena water, i.e., absorption, attenuation, and scattering coefficients, during the period of maximum runoff. This aimed to contribute to the development of a bio-optical model for use as the basis for optical remote sensing of coastal water of the Arctic. In this context the absorption by CDOM (colored dissolved organic matter) and particles, and the concentrations of total suspended matter, phytoplankton-pigments, and carbon were measured. CDOM was found to be the most dominant parameter affecting the optical properties of the river, with an absorption coefficient of 4.5-5 m-1 at 442 nm, which was almost four times higher than total particle absorption values at visible wavelength range. The wavelenght-dependence of absorption of the different water constituents was chracterized by determining the semi logarithmic spectral slope. Mean CDOM, and detritus slopes were 0.0149 nm-1(standard deviation (stdev) = 0.0003, n = 18), and 0.0057 nm-1 (stdev = 0.0017, n = 19), respectively, values which are typical for water bodies with high concentrations of dissolved and particulate carbon. Mean chlorophyll a and total suspended matter were 1.8 mg m-3 (stdev = 0.734 n = 18) and 31.9 g m-3 (stdev = 19.94, n = 27), respectively. DOC (dissolved organic carbon) was in the range 8-10 g m-3 and the total particulate carbon (PC) in the range 0.25-1.5 g m-3. The light penetration depth (Secchi disc depth) was in the range 30-90 cm and was highly correlated with the suspended matter concentration. The period of maximum river runoff in June was chosen to obtain bio-optical data when maximum water constituents are transported into the Laptev Sea. However, we are aware that more data from other seasons and other years need to be collected to establish a general bio-optical model of the Lena water and conclusively characterize the light climate with respect to primary production.

Effect of Pre-Oxidation Treatment of Nano-SiC Particulates on Microstructure and Mechanical Properties of SiC/Mg-8Al-1Sn Composites Fabricated by Powder Metallurgy Combined with Hot Extrusion.

PubMed

Li, Chuan-Peng; Wang, Zhi-Guo; Zha, Min; Wang, Cheng; Yu, Hong-Chen; Wang, Hui-Yuan; Jiang, Qi-Chuan

2016-11-26

Nano-SiC particulates (n-SiC p ) reinforced Mg-8Al-1Sn (AT81) composites with different pre-oxidation parameters were fabricated by powder metallurgy (P/M) process combined with hot extrusion. The effects of pre-oxidization treatment of n-SiC p on the microstructure and tensile properties of 0.5 vol % n-SiC p /AT81 composites were investigated accordingly. The distribution of n-SiC p with different pre-oxidation parameters was homogeneous in the composites. Moreover, it was found that a thin MgAl₂O₄ layer formed at the interface when the n-SiC p were pre-oxidized at 1073 K for 2 h, while the MgAl₂O₄ layer became much thicker with pre-oxidization temperature increasing to 1273 K for 2 h. After an appropriate pre-oxidization treatment of n-SiC p at 1073 K for 2 h, the as-extruded 0.5 vol % n-SiC p /AT81 composites exhibited an enhanced strength. It was found that the yield strength (YS) and ultimate tensile strength (UTS) increased from 168 MPa and 311 MPa to 255 MPa and 393 MPa compared with the as-extruded AT81 alloy, reflecting 51.8% and 26.4% increments, respectively. The improvement of mechanical properties should be mainly attributed to the grain refinement and homogeneous distribution of n-SiC p in the composites. Moreover, a well-bonded interface and the formation of an appropriate amount of interfacial product (MgAl₂O₄) benefited the material's mechanical properties.

Bioavailable dissolved and particulate organic carbon flux from coastal temperate rainforest watersheds

NASA Astrophysics Data System (ADS)

Fellman, J.; Hood, E. W.; D'Amore, D. V.; Moll, A.

2017-12-01

Coastal temperate rainforest (CTR) watersheds of southeast Alaska have dense soil carbon stocks ( 300 Mg C ha-1) and high specific discharge (1.5-7 m yr-1) driven by frontal storms from the Gulf of Alaska. As a result, dissolved organic carbon (DOC) fluxes from Alaskan CTR watersheds are estimated to exceed 2 Tg yr-1; however, little is known about the export of particulate organic carbon (POC). The magnitude and bioavailability of this land-to-ocean flux of terrigenous organic matter ultimately determines how much metabolic energy is translocated to downstream and coastal marine ecosystems in this region. We sampled streamwater weekly from May through October from four watersheds of varying landcover (gradient of wetland to glacial coverage) to investigate changes in the concentration and flux of DOC and POC exported to the coastal ocean. We also used headspace analysis of CO2 following 14 day laboratory incubations to determine the flux of bioavailable DOC and POC exported from CTR watersheds. Across all sites, bioavailable DOC concentrations ranged from 0.2 to 1.9 mg L-1 but were on average 0.6 mg L-1. For POC, bioavailable concentrations ranged from below detection to 0.3 mg L-1 but were on average 0.1 mg L-1. The concentration, flux and bioavailability of DOC was higher than for POC highlighting the potential importance of DOC as a metabolic subsidy to downstream and coastal environments. Ratios of DOC to POC decreased during high flow events because the increase in POC concentrations with discharge exceeds that for DOC. Overall, our findings suggest that projected increases in precipitation and storm intensity will drive changes in the speciation, magnitude and bioavailability of the organic carbon flux from CTR watersheds.

Effect of Pre-Oxidation Treatment of Nano-SiC Particulates on Microstructure and Mechanical Properties of SiC/Mg-8Al-1Sn Composites Fabricated by Powder Metallurgy Combined with Hot Extrusion

PubMed Central

Li, Chuan-Peng; Wang, Zhi-Guo; Zha, Min; Wang, Cheng; Yu, Hong-Chen; Wang, Hui-Yuan; Jiang, Qi-Chuan

2016-01-01

Nano-SiC particulates (n-SiCp) reinforced Mg-8Al-1Sn (AT81) composites with different pre-oxidation parameters were fabricated by powder metallurgy (P/M) process combined with hot extrusion. The effects of pre-oxidization treatment of n-SiCp on the microstructure and tensile properties of 0.5 vol % n-SiCp/AT81 composites were investigated accordingly. The distribution of n-SiCp with different pre-oxidation parameters was homogeneous in the composites. Moreover, it was found that a thin MgAl2O4 layer formed at the interface when the n-SiCp were pre-oxidized at 1073 K for 2 h, while the MgAl2O4 layer became much thicker with pre-oxidization temperature increasing to 1273 K for 2 h. After an appropriate pre-oxidization treatment of n-SiCp at 1073 K for 2 h, the as-extruded 0.5 vol % n-SiCp/AT81 composites exhibited an enhanced strength. It was found that the yield strength (YS) and ultimate tensile strength (UTS) increased from 168 MPa and 311 MPa to 255 MPa and 393 MPa compared with the as-extruded AT81 alloy, reflecting 51.8% and 26.4% increments, respectively. The improvement of mechanical properties should be mainly attributed to the grain refinement and homogeneous distribution of n-SiCp in the composites. Moreover, a well-bonded interface and the formation of an appropriate amount of interfacial product (MgAl2O4) benefited the material’s mechanical properties. PMID:28774083

Preliminary Characterization of Organic Geochemistry in the Fly-Strickland River System, Papua New Guinea

NASA Astrophysics Data System (ADS)

Alin, S. R.; Aalto, R.; Remington, S. M.; Richey, J. E.

2003-12-01

The Fly-Strickland fluvial dispersal system comprises one of the largest river basins in tropical Oceania, ranking among the top 20 rivers in the world for water and sediment discharge. From the New Guinea highlands, these rivers flow >1000 km across lowland tropical floodplains to the Gulf of Papua, with an average annual depth of runoff 100 times that of the Amazon. Within the system, the Strickland has greater sediment discharge and a steeper gradient than the Fly, providing an opportunity to investigate biogeochemical differences associated with particulate flux. For eight lowland sites across the Fly-Strickland river system, we analyzed water and suspended sediment (SS) samples for an initial survey of various carbon cycle parameters. Both the Fly and Strickland Rivers were strongly supersaturated with carbon dioxide (2008-10,479 uatm CO2) and undersaturated with oxygen (1.10-5.48 mg/l O2), with the Fly having higher CO2 and lower O2 concentrations than the Strickland River. These pCO2 and O2 concentrations are comparable to and lower than (respectively) typical values in the Amazon. Measured Fly-Strickland alkalinity values fell in the range of 0.893-1.888 meq, and pH measurements were neutral to slightly alkaline (6.916-7.852). In a sample from a sediment-impoverished tributary from Lake Murray to the Strickland (Herbert R.), pH was neutral (7.060), and alkalinity and pCO2 had their lowest observed values at 0.234 meq and 1407 uatm, respectively. Nutrient concentrations were generally higher in the Strickland ([NO3]=3.36+/-0.69 uM, [PO4]=0.09+/-0.10 uM, and [Si(OH)4]=176.6+/-41.7 uM) than in the Fly River ([NO3]=1.09+/-0.04 uM, [PO4]=0.01+/-0.01 uM, and [Si(OH)4]=110.6+/-4.8 uM). NO3 and PO4 concentrations in the Fly-Strickland river system were lower than in the Amazon, and silicate was comparable. SS concentrations were higher in the Strickland than in the Fly (49.4-231.1 mg/l vs. 19.5-59.6 mg/l). Coarse particulates were organic-poor in the Fly and Strickland rivers, with <1% organic carbon (OC). Fine particulates contained more OC in the Fly (2.32-9.03%) than in the Strickland (0.99-3.08%). In aggregate, the average OC concentration of Fly-Strickland river SS samples is 3.75+/-3.07%, which is substantially higher than %OC values measured in fine particulates in the Amazon. C/N ratios for fine particulate organic matter (FPOM) are higher in the Fly (13.0-24.1) than in the Strickland (9.5-14.4), suggesting a greater contribution of N-poor, terrestrial organics to the Fly River. FPOM δ 13C values in the Fly are more depleted (-31.1--30.3‰ ) than in the Strickland River (-29.6--28.4‰ ). We intend to estimate the total biogeochemical fluxes associated with these reported concentrations. Collectively, these preliminary data on carbon cycling in the Fly and Strickland rivers suggest that this fluvial dispersal system outgases a substantial volume of CO2 each year relative to its area, much like the Amazon River. However, in contrast to the Amazon, where the majority of the sediment from the Andes is trapped in sub-aerial, intra-cratonal basins, most fluviatile sediment is advected beyond the Fly River mouth. Therefore, due to the higher organic content of the fine suspended sediment in this river system, it seems probable that a relatively greater export and burial flux of organic carbon may occur within the delta and shelf deposits of the Gulf of Papua.

Bioactive and total endotoxins in atmospheric aerosols in the Pearl River Delta region, China

NASA Astrophysics Data System (ADS)

Cheng, Jessica Y. W.; Hui, Esther L. C.; Lau, Arthur P. S.

2012-02-01

Endotoxin, a toxic and pyrogenic substance in gram-negative bacteria in atmospheric aerosols was measured over a period of one year at Nansha, Guangzhou and Hong Kong in the Pearl River Delta region, China. Atmospheric aerosols were collected by high-volume samplers. The bioactive endotoxin levels in the samples were determined using the Limulus Amebocyte Lysate (LAL) assay after extraction with pyrogen-free water while the total endotoxin levels were measured by quantifying the biomarker, 3-hydroxy fatty acids (3-OHFAs) with GC-MS. Results showed that there was no significant difference (0.19 < p < 0.81) in the bioactive endotoxin level in PM 10 among sites (average concentrations ranged from 0.34 to 0.39 EU m -3). However, Hong Kong showed a significantly lower ( p < 0.05) total endotoxin level in PM 10 (average of 17.4 ng m -3) compared with Nansha's 29.4 ng m -3 and Guangzhou's 32.7 ng m -3. The bioactive endotoxins were found to be associated with the coarse mode (PM 2.5-10) of the particulates of natural origins while the total endotoxins were associated more with the fine mode (PM 2.5) of the particulates of anthropogenic origins. When normalized with particulate mass, the endotoxin loading is much higher in summer as a result of the increased growth of the bacteria when climatic conditions are favorable. The chemically determined total endotoxins were 3-4 orders of magnitude higher than the bioactive endotoxins quantified using the LAL assay. Correlation analyses between the bioactive endotoxins and 3-OHFAs with different carbon length were analyzed. Results showed that the correlations detected vary among sites and particulate sizes. Although no generalization between the total and bioactive endotoxins can be drawn from the study, the levels reported in this study suggests that the discrepancies between the two measurement approaches, and the bioactive potential of 3-OHFAs with individual carbon chains deserve further investigation.

Trace metal content in inhalable particulate matter (PM2.5-10 and PM2.5) collected from historical mine waste deposits using a laboratory-based approach.

PubMed

Martin, Rachael; Dowling, Kim; Pearce, Dora C; Florentine, Singarayer; McKnight, Stafford; Stelcer, Eduard; Cohen, David D; Stopic, Attila; Bennett, John W

2017-06-01

Mine wastes and tailings are considered hazardous to human health because of their potential to generate large quantities of highly toxic emissions of particulate matter (PM). Human exposure to As and other trace metals in PM may occur via inhalation of airborne particulates or through ingestion of contaminated dust. This study describes a laboratory-based method for extracting PM 2.5-10 (coarse) and PM 2.5 (fine) particles from As-rich mine waste samples collected from an historical gold mining region in regional, Victoria, Australia. We also report on the trace metal and metalloid content of the coarse and fine fraction, with an emphasis on As as an element of potential concern. Laser diffraction analysis showed that the proportions of coarse and fine particles in the bulk samples ranged between 3.4-26.6 and 0.6-7.6 %, respectively. Arsenic concentrations were greater in the fine fraction (1680-26,100 mg kg -1 ) compared with the coarse fraction (1210-22,000 mg kg -1 ), and Co, Fe, Mn, Ni, Sb and Zn were found to be present in the fine fraction at levels around twice those occurring in the coarse. These results are of particular concern given that fine particles can accumulate in the human respiratory system. Our study demonstrates that mine wastes may be an important source of metal-enriched PM for mining communities.

Chemical leaching methods and measurements of marine labile particulate Fe

NASA Astrophysics Data System (ADS)

Revels, B. N.; John, S.

2012-12-01

Iron (Fe) is an essential nutrient for life. Yet its low solubility and concentration in the ocean limits marine phytoplankton productivity in many regions of the world. Dissolved phase Fe (<0.4μm) has traditionally been considered the most biologically accessible form, however, the particulate phase (>0.4μm) may contain an important, labile reservoir of Fe that may also be available to phytoplankton. However, concentration data alone cannot elucidate the sources of particulate Fe to the ocean and to what extent particulate iron may support phytoplankton growth. Isotopic analysis of natural particles may help to elucidate the biogeochemical cycling of Fe, though it is important to find a leaching method which accesses bioavailable Fe. Thirty-three different chemical leaches were performed on a marine sediment reference material, MESS-3. The combinations included four different acids (25% acetic acid, 0.01M HCl, 0.5M HCl, 0.1M H2SO4 at pH2), various redox conditions (0.02M hydroxylamine hydrochloride or 0.02M H2O2), three temperatures (25°C, 60°C, 90°C), and three time points (10 minutes, 2 hours, 24 hours). Leached Fe concentrations varied from 1mg/g to 35mg/g, with longer treatment times, stronger acids, and hotter temperatures generally associated with an increase in leached Fe. δ56Fe in these leaches varied from -1.0‰ to +0.2‰. Interestingly, regardless of leaching method used, there was a very similar relationship between the amount of Fe leached from the particles and the δ56Fe of this iron. Isotopically lighter δ56Fe values were associated with smaller amounts of leached Fe whereas isotopically heavier δ56Fe values were associated with larger amounts of leached Fe. Two alternate hypotheses could explain these data. Either, the particles may contain pools of isotopically light Fe that are easily accessed early in dissolution, or isotopically light Fe may be preferentially leached from the particle due to a kinetic isotope effect during dissolution. To explore the first hypothesis, we modeled dissolution of Fe from particles assuming two separate pools, labile and refractory. The model produces a good fit to the data assuming 3mg/g of a labile Fe pool with δ56Fe = -0.9‰ and a refractory Fe pool with δ56Fe = +0.1‰. If the second hypothesis is true, and there is a kinetic isotope effect during dissolution, the similar relationship between amount of Fe leached and δ56Fe for both organic and mineral acids suggests that Fe is leached from particles via proton-promoted dissolution. Several of these leaching techniques will be employed on sediment trap material from the Cariaco Basin to further investigate the relationship between δ56Fe and the labile, bioavailable fraction of iron particles. A leach or series of leaches will be chosen to provide the most useful information about the bioavailability of iron from particles, and they will be applied to filtered particle samples from portions of the US GEOTRACES A10 (North Atlantic) transect. δ56Fe values from particulate material in these regions will provide a better understanding of the sources of particulate iron to the ocean, and may help to trace how particulate iron is involved in global biogeochemical cycles.

Particulate concentrations during on-farm combustion of energy crops of different shapes and harvest seasons

NASA Astrophysics Data System (ADS)

Fournel, S.; Palacios, J. H.; Morissette, R.; Villeneuve, J.; Godbout, S.; Heitz, M.; Savoie, P.

2015-03-01

The increasing energy costs and environmental concerns of farms have motivated the growing interest of agricultural producers in using farm-grown biomass as a substitute to fossil fuels for heat production. However, the use of non-woody biomass is facing challenges due to variability regarding chemical composition and fuel properties that may induce problems during combustion such as particulate matter (PM). The aim of this work was to measure and compare total PM concentrations during on-farm combustion of wood and four agricultural crops: short-rotation willow, switchgrass, miscanthus and reed canary grass. In order to study the influence of physicochemical properties, different shapes (pellets, chips and chopped grasses) and harvest seasons (fall and spring) were also evaluated. In this context, a representative small-scale (29 kW), multi-fuel boiler for light commercial use was utilized. The boiler was also non-catalytic so that the burning took place in a single combustion chamber. Overall, twelve different biomass fuels were tested and each product was burned three times. Mean PM concentration of wood (416 mg Nm-3 at 7 vol% O2) was lower than that of the four dedicated energy crops (505-1417 mg Nm-3 at 7 vol% O2). However, because of the high variability between the experiments, no statistical significance was observed at P > 0.1 level except in one case. The PM amounts were high compared to literature data and Quebec's environmental regulation mainly because of the boiler system used. Except for willow, pelletized products decreased PM levels by 22-52% compared to chopped materials. Bulky biomass of low density was unable to reach steady-state conditions and produced compounds associated with incomplete combustion including PM. Spring-harvested biomass fuels showed a PM reduction up to 48% compared to fall-harvested crops. This was likely due to a 20-60% decrease of several chemical elements in the biomass, namely S, Cl, K and P which are the main constituents of fly ash.

Coal and tire burning mixtures containing ultrafine and nanoparticulate materials induce oxidative stress and inflammatory activation in macrophages.

PubMed

Gasparotto, Juciano; Somensi, Nauana; Caregnato, Fernanda F; Rabelo, Thallita K; DaBoit, Kátia; Oliveira, Marcos L S; Moreira, José C F; Gelain, Daniel P

2013-10-01

Ultra-fine and nano-particulate materials resulting from mixtures of coal and non-coal fuels combustion for power generation release to the air components with toxic potential. We evaluated toxicological and inflammatory effects at cellular level that could be induced by ultrafine/nanoparticles-containing ashes from burning mixtures of coal and tires from an American power plant. Coal fly ashes (CFA) samples from the combustion of high-S coal and tire-derived fuel, the latter about 2-3% of the total fuel feed, in a 100-MW cyclone utility boiler, were suspended in the cell culture medium of RAW 264.7 macrophages. Cell viability, assessed by MTT reduction, SRB incorporation and contrast-phase microscopy analysis demonstrated that CFA did not induce acute toxicity. However, CFA at 1mg/mL induced an increase of approximately 338% in intracellular TNF-α, while release of this proinflammatory cytokine was increased by 1.6-fold. The expression of the inflammatory mediator CD40 receptor was enhanced by 2-fold, the receptor for advanced glycation endproducts (RAGE) had a 5.7-fold increase and the stress response protein HSP70 was increased nearly 12-fold by CFA at 1mg/mL. Although CFA did not induce cell death, parameters of oxidative stress and reactive species production were found to be altered at several degrees, such as nitrite accumulation (22% increase), DCFH oxidation (3.5-fold increase), catalase (5-fold increase) and superoxide dismutase (35% inhibition) activities, lipoperoxidation (4.2 fold-increase) and sulfhydryl oxidation (40% decrease in free SH groups). The present results suggest that CFA containing ultra-fine and nano-particulate materials from coal and tire combustion may induce sub-chronic cell damage, as they alter inflammatory and oxidative stress parameters at the molecular and cellular levels, but do not induce acute cell death. © 2013.

Size and composition distributions of particulate matter emissions: part 2--heavy-duty diesel vehicles.

PubMed

Robert, Michael A; Kleeman, Michael J; Jakober, Christopher A

2007-12-01

Particulate matter (PM) emissions from heavy-duty diesel vehicles (HDDVs) were collected using a chassis dynamometer/dilution sampling system that employed filter-based samplers, cascade impactors, and scanning mobility particle size (SMPS) measurements. Four diesel vehicles with different engine and emission control technologies were tested using the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) 5 mode driving cycle. Vehicles were tested using a simulated inertial weight of either 56,000 or 66,000 lb. Exhaust particles were then analyzed for total carbon, elemental carbon (EC), organic matter (OM), and water-soluble ions. HDDV fine (< or =1.8 microm aerodynamic diameter; PM1.8) and ultrafine (0.056-0.1 microm aerodynamic diameter; PM0.1) PM emission rates ranged from 181-581 mg/km and 25-72 mg/km, respectively, with the highest emission rates in both size fractions associated with the oldest vehicle tested. Older diesel vehicles produced fine and ultrafine exhaust particles with higher EC/OM ratios than newer vehicles. Transient modes produced very high EC/OM ratios whereas idle and creep modes produced very low EC/OM ratios. Calcium was the most abundant water-soluble ion with smaller amounts of magnesium, sodium, ammonium ion, and sulfate also detected. Particle mass distributions emitted during the full 5-mode HDDV tests peaked between 100-180 nm and their shapes were not a function of vehicle age. In contrast, particle mass distributions emitted during the idle and creep driving modes from the newest diesel vehicle had a peak diameter of approximately 70 nm, whereas mass distributions emitted from older vehicles had a peak diameter larger than 100 nm for both the idle and creep modes. Increasing inertial loads reduced the OM emissions, causing the residual EC emissions to shift to smaller sizes. The same HDDV tested at 56,000 and 66,000 lb had higher PM0.1 EC emissions (+22%) and lower PM0.1 OM emissions (-38%) at the higher load condition.

Distribution, sedimentation, and bioavailability of particulate phosphorus in the mainstream of the Three Gorges Reservoir.

PubMed

Tang, Xianqiang; Wu, Min; Li, Rui

2018-09-01

The transportation and sedimentation of particulate phosphorus (PP) in a huge reservoir such as the Three Gorges Reservoir (TGR) are closely related to the phosphorus distribution characteristics and nutritional status of the water body. In this study, the PP distribution, sedimentation, and bioavailability in the mainstream section of the TGR were investigated through a field survey, indoor simulated settlement experiment, and historical data analysis. The results indicated that PP was the major component of the total phosphorus (TP) and that the Three Gorges Dam (TGD) trapped nearly 76.25% of suspended sediment (SS) and 75.35% of PP in the TGR, even during the flood season. A decline in flow velocity promoted the deposition of PP; additionally, PP concentrations gradually dropped from 0.35 mg/L in Chongqing to 0.02 mg/L in Zigui. The static PP sedimentation process adequately fitted a pseudo-second-order kinetic equation with a maximum correlation coefficient of 0.97. Moreover, more than half of the PP sedimentation process was achieved in less than 60 min for samples collected from the upper river reaches within simulated sedimentation process. The median particle size of SS and absolute value of the water column's zeta potential were negatively and positively related to the t 12 values of PP sedimentation, respectively. Compared with the concentration and particle size of SS obtained in the pre-TGR period, the values in the mainstream section of the TGR were lower. However, the TP and Fe/Al-P contents in SS increased several times. Due to the combined effects of flow velocity reduction and SS trapping, the water transparency and bioavailability of water column phosphorus were enhanced. Thus, the risk of water bloom outburst significantly increased when the impounded water level of 175 m in the TGR became the normal state. Copyright © 2018 Elsevier Ltd. All rights reserved.

Fabrication of cast particle-reinforced metals via pressure infiltration

NASA Technical Reports Server (NTRS)

Klier, E. M.; Mortensen, A.; Cornie, J. A.; Flemings, M. C.

1991-01-01

A new casting process for fabrication of particle-reinforced metals is presented whereby a composite of particulate reinforcing phase in metal is first produced by pressure infiltration. This composite is then diluted in additional molten metal to obtain the desired reinforcement volume fraction and metal composition. This process produces a pore-free as-cast particulate metal-matrix composite. This process is demonstrated for fabrication of magnesium-matrix composites containing SiC reinforcements of average diameter 30, 10 and 3 microns. It is compared with the compocasting process, which was investigated as well for similar SiC particles in Mg-10 wt pct Al, and resulted in unacceptable levels of porosity in the as-cast composite.

Air quality assessment and the use of specific markers to apportion pollutants to source

NASA Astrophysics Data System (ADS)

Douce, David Stewart

The contributions of specific polluting sources to both indoor and outdoor atmospheric pollution are difficult to determine, as solid and gaseous products from different combustion sources are often similar. Sometimes, however, a marker compound can be identified that is unique to a pollution source (or at least not present in most other local combustion sources) and which will allow assessment of the contribution of that source to total atmospheric pollution.The aim of this study was to identify suitable marker compounds and methods for the apportionment (assessment of percentage contribution) of specific sources to atmospheric pollution. The sources selected were diesel exhaust emissions in outdoor, and environmental tobacco smoke (ETS) in indoor environments. Studies with controlled (laboratory) atmospheres would be followed by field studies using these methods and markers to produce apportionments for these sources to air pollution in selected environments. Initial analysis of such polluting sources was therefore the qualitative analysis of volatile compounds and particulate associated material, both organic and inorganic. Volatile organic compounds were adsorbed onto various resins, while particulate material was sampled onto various filter paper types. Organics were determined by GC-AED and GC-MS, and elements by ICP-MS.1-Nitropyrene was identified as a suitable marker for diesel particulate emissions (<5um). A large volume air sample from Sheffield city centre using 1-nitropyrene as a marker suggested that 63% of atmospheric particulate material (<5um) might be of diesel origin. However the concentration of 1-nitropyrene is low in atmospheric samples, and in the volumes used in routine sampling the amount of 1-nitropyrene was below the limit of detection on the instrument used. In an alternative approach the aliphatic alkane tetracosane (C24) was used as a diesel marker for urban air, with a 1-nitropyrene:tetracosane ratio derived from the average results from laboratory experiments with a diesel engine running at various speeds and loads. This approach yielded apportionment values ranging from 5-85% for the diesel contribution to particulate material (<5mum) in the urban air of Sheffield. No volatile marker compound was found for diesel apportionment.The contribution of ETS to atmospheric pollution has previously been estimated from the measurement of respirable suspended particulates (RSP), which was superseded by total UV absorbance and total fluorescence of a methanol extract. More recent work has suggested the use of solanesol or scopoletin as marker compounds. This thesis shows that the non specific methods overestimated the particulate contribution of ETS in some atmospheres, and that solanesol is a better marker compound than scopoletin. Preliminary studies from a small number of smokers homes and offices, with solanesol as a marker compound for particulate ETS, indicated that ETS contributions to total particulate material (<5mum) ranged from 6 to 49% in homes and 11 to 28% in offices.Pyrrole was used as a marker for ETS contribution to volatile organic pollution, and studies with controlled atmospheres with a smoking machine allowed calculation of the ratios of pyrrole to other volatile organic compounds (VOC's) in ETS. Samples from the field study were used to produce apportionment percentage levels of benzene, toluene, o-xylene and p+m-xylene associated with ETS.In addition the use of tree bark as a atmospheric sink for airborne particulates was investigated. Six nitrated polycyclic aromatic hydrocarbons associated with diesel emissions were quantified in bark extracts and levels of these were found to be highest during winter months.

Experimental investigation and modelling approach of the impact of urban wastewater on a tropical river; a case study of the Nhue River, Hanoi, Viet Nam

NASA Astrophysics Data System (ADS)

Duc, Trinh Anh; Vachaud, Georges; Bonnet, Marie Paule; Prieur, Nicolas; Loi, Vu Duc; Anh, Le Lan

2007-02-01

SummaryAnalyses of water quality and flow regime in combination with laboratory studies and ecological modelling were used to assess the water quality impact of pollution from to To Lich River that drains through Hanoi City and greatly contaminates the Nhue River. With an average discharge of 26.2 m 3/s, the Nhue River receives about 5.8 m 3/s of untreated domestic water from the city's main open-air-sewer - the To Lich River. The studies during 2002-2003 showed high concentrations of BOD (70 mg O 2/l), DOC (15 mg C/l), coliform (2.4e 6 MNP/100 ml), total phosphorus (3.5 mg P/l), and total nitrogen (31.6 mg N/l) in the To Lich, while DO level was less than 1 mg O 2/l. Such high loads of untreated wastewater impacted water quality in the Nhue River where DO decreased at times to as low as 1 mg O 2/l. The accumulation of particulate organic matter and micro-organisms in the sediments of the Nhue represented substantial sources of nutrients and sinks for DO. They are also considerable production of dissolved carbon dioxide at concentrations up to two orders of magnitude higher than pressure. Such pressures ( EpCO 2) are expected in polluted environments, but the results presented here are new for Vietnam and much of developing countries. A number of factors linked to field monitoring and laboratory measurements clearly indicate the importance of autotrophic over heterotrophic biological processes and sediments. An ecological model for management purposes has been developed that reliably estimates of the pollutant loads. An opportunity was taken to examine the changing impacts and processes when the To Lich was diverted from the Nhue. The monitoring and modelling of this opportunity showed low dissolved oxygen levels even if the impact from the To Lich was lessened. Alternatives are proposed to alleviate problems of water quality in the Nhue. It is concluded that the treatment of the To Lich River's water is highly recommended; otherwise a reduction to one third of current wastewater discharge is needed to bring water quality back to the environmental standard.

High performance YBCO films. Quarterly status report No. 6, 1 February-30 April 1993. [YBCO (yttrium barium copper oxides)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denlinger, E.J.; Fathy, A.; Kalokitis, D.

1993-04-30

YBCO on MgF2 withstood post annealing to 750 deg C without deterioration. This allows the deposition of high quality multiple layer YBCO films onto both sides of a MgF2 substrate. GdBaCuO films were deposited onto LaAlO3 and appear to be superior to YBCO in terms of lower particulate density, slightly higher T[sub c]'s, and higher critical current density. The ramifications could be very beneficial to the MCM program. Furthermore, the tolerance of these films to a wider range of deposition conditions indicates a possibility of using these films on MgF2.

Anthropogenic fugitive, combustion and industrial dust is a significant, underrepresented fine particulate matter source in global atmospheric models

NASA Astrophysics Data System (ADS)

Philip, Sajeev; Martin, Randall V.; Snider, Graydon; Weagle, Crystal L.; van Donkelaar, Aaron; Brauer, Michael; Henze, Daven K.; Klimont, Zbigniew; Venkataraman, Chandra; Guttikunda, Sarath K.; Zhang, Qiang

2017-04-01

Global measurements of the elemental composition of fine particulate matter across several urban locations by the Surface Particulate Matter Network reveal an enhanced fraction of anthropogenic dust compared to natural dust sources, especially over Asia. We develop a global simulation of anthropogenic fugitive, combustion, and industrial dust which, to our knowledge, is partially missing or strongly underrepresented in global models. We estimate 2-16 μg m-3 increase in fine particulate mass concentration across East and South Asia by including anthropogenic fugitive, combustion, and industrial dust emissions. A simulation including anthropogenic fugitive, combustion, and industrial dust emissions increases the correlation from 0.06 to 0.66 of simulated fine dust in comparison with Surface Particulate Matter Network measurements at 13 globally dispersed locations, and reduces the low bias by 10% in total fine particulate mass in comparison with global in situ observations. Global population-weighted PM2.5 increases by 2.9 μg m-3 (10%). Our assessment ascertains the urgent need of including this underrepresented fine anthropogenic dust source into global bottom-up emission inventories and global models.

Determination of Vanadium, Tin and Mercury in Atmospheric Particulate Matter and Cement Dust Samples by Direct Current Plasma Atomic Emission Spectrometry.

ERIC Educational Resources Information Center

Hindy, Kamal T.; And Others

1992-01-01

An atmospheric pollution study applies direct current plasma atomic emission spectrometry (DCP-AES) to samples of total suspended particulate matter collected in two industrial areas and one residential area, and cement dust collected near major cement factories. These samples were analyzed for vanadium, tin, and mercury. The results indicate the…

Bioaccessibility of U, Th and Pb in particulate matter from an abandoned uranium mine

NASA Astrophysics Data System (ADS)

Millward, Geoffrey; Foulkes, Michael; Henderson, Sam; Blake, William

2016-04-01

Currently, there are approximately 150 uranium mines in Europe at various stages of either operation, development, decommissioning, restoration or abandonment (wise-uranium.com). The particulate matter comprising the mounds of waste rock and mill tailings poses a risk to human health through the inadvertent ingestion of particles contaminated with uranium and thorium, and their decay products, which exposes recipients to the dual toxicity of heavy elements and their radioactive emissions. We investigated the bioaccessibility of 238U, 232Th and 206,214,210Pb in particulate samples taken from a contaminated, abandoned uranium mine in South West England. Sampling included a mine shaft, dressing floor and waste heap, as well as soils from a field used for grazing. The contaminants were extracted using the in-vitro Unified Bioaccessibility Research Group of Europe Method (UBM) in order to mimic the digestion processes in the human stomach (STOM) and the combined stomach and gastrointestinal tract (STOM+INT). Analyses of concentrations of U, Th and Pb in the extracts were by ICP-MS and the activity concentrations of radionuclides were determined on the same particles, before and after extraction, using gamma spectroscopy. 'Total' concentrations of U, Th and Pb for all samples were in the range 57 to 16,200, 0.28 to 3.8 and 69 to 4750 mg kg-1, respectively. For U and Pb the concentrations in the STOM fraction were lower than the total and STOM+INT fractions were even lower. However, for Th the STOM+INT fractions were higher than the STOM due to the presence of Th carbonate species within the gastrointestinal fluid. Activity concentrations for 214Pb and 210Pb, including total, STOM and STOM+INT, were in the range 180 to <1 Bq g-1 for the dressing floor and waste heap and 18 to <1 Bq g-1 for the grazing land. Estimates of the bioaccessible fractions (BAFs) of 238U in the most contaminated samples were 39% and 8% in the STOM and STOM+INT, respectively, whereas the respective BAFs for 232Th were 3% and 9%. For stable 206Pb the STOM and STOM+INT BAFs were 16% and 3% for the most contaminated samples, whereas those from the field had 44% in the STOM fraction and 17% in the STOM+INT fraction. The BAFs for 214Pb and 210Pb were the same as 206Pb. Dose estimates were made for the contaminants together with radioactive doses in order to assess potential risk to human health.

Nitrogen and phosphorus associating with different size suspended solids in roof and road runoff in Beijing, China.

PubMed

Wu, Junliang; Ren, Yufen; Wang, Xuemei; Wang, Xiaoke; Chen, Liding; Liu, Gangcai

2015-10-01

Roofs and roads, accounting for a large portion of the urban impervious land surface, have contributed significantly to urban nonpoint pollution. In this study, in Beijing, China, roof and road runoff are sampled to measure the suspended solids (SS), nitrogen (N), and phosphorus (P) contained in particles with different sizes. The SS content in the road runoff (151.59 mg/L) was sevenfold that in the roof runoff (21.13 mg/L, p < 0.05). The SS contained more coarse particulates in the roof runoff than in road runoff. The small particulates in the range of 0.45-50 μm consisted of 59 % SS in the roof runoff and 94 % SS in the road runoff. P was mainly attached to particle sizes of 10-50 μm in the roof (73 %) and road (48 %) runoffs, while N was mainly in a dissolved phase state in both runoffs. So, the different associations of N and P raise a challenge in preventing stormwater pollution in urban environments.

Wear properties of 10 vol.% silicon carbide particulate-reinforced aluminum composite fabricated by powder injection molding

NASA Astrophysics Data System (ADS)

Patcharawit, T.; Ngeekoh, A.; Chuankrekkul, N.

2017-09-01

Wear properties of aluminum matrix composites reinforced with silicon carbide particulate of 10 vol.% addition was investigated in as-sintered and heat-treated conditions under varying loads at -5, -25, -45 and -65N using a ball on flat type of wear test. The composite was fabricated by powder injection molding and sintering at 650 °C for 3 hours. Solution treatment was carried out at 550 °C for 2 hours followed by age-hardening at 160 °C for 6 hours. SEM and XRD results indicated Al and SiCp are present as matrix and reinforcement, while AlN, Al2Cu and Mg2Si were also detected. Further precipitation of Al2Cu and Mg2Si in heat-treated samples promoted maximum macro and micro Vickers hardness values, which were achieved at 161 and 157 Hv respectively. Wear weight loss increased with increasing minus load level. The coefficient of friction was found in the range of 0.042-0.048. Wear mechanisms were determined as the combination of abrasive, adhesion and oxidation.

Systematic evaluation of dissolved lead sorption losses to particulate syringe filter materials.

PubMed

Minning, Thomas; Lytle, Darren A; Pham, Maily; Kelty, Keith

2015-06-01

Distinguishing between soluble and particulate lead in drinking water is useful in understanding the mechanism of lead release and identifying remedial action. Typically, particulate lead is defined as the amount of lead removed by a 0.45-μm filter. Unfortunately, there is little guidance regarding selection of filter membrane material and little consideration to the possibility of the sorption of dissolved lead to the filter. The objective of this work was to examine the tendency of 0.45-μm syringe filter materials to adsorb lead. Tests were performed with water containing 40 and 24 μg/L soluble lead at pH 7 buffered with 50 mg C/L dissolved inorganic concentration (DIC). The amounts of lead sorbed greatly varied by filter, and only two filter types, polypropylene and mixed cellulose esters, performed well and are recommended. Great care must be taken in choosing a filter when filtering soluble lead and interpreting filter results.

Quantitative mapping of particulate iron in an ocean dump using remotely sensed data

NASA Technical Reports Server (NTRS)

Ohlhorst, C. W.; Bahn, G. S.

1978-01-01

A remote sensing experiment was conducted at the industrial acid waste ocean dump site located approximately 38 n mi SE of Cape Henlopen, Delaware, to see if there was a relationship between aircraft remotely sensed spectral signatures and the iron concentration measured in the plume. Results are presented which show that aircraft remotely sensed spectral data can be used to quantify and map an acid waste dump in terms of its particulate iron concentration. A single variable equation using the ratio of band 2 (440-490 nm) radiance to band 4 (540-580 nm) radiance was used to quantify the acid plume and the surrounding water. The acid waste varied in age from freshly dumped to 3 1/2 hours old. Particulate iron concentrations in the acid waste were estimated to range up to 1.1 mg/liter at the 0.46 meter depth. A classification technique was developed to remove sunglitter-affected pixels from the data set.

Trace metals in the Ob and Yenisei Rivers' Estuaries (the Kara Sea).

NASA Astrophysics Data System (ADS)

Demina, L. L.

2014-12-01

Behavior of some trace metals (Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni and Pb) in water column (soluble <0.45 µm and particulate fractions) and bottom sediments (surface and cores) along the two transects from the Ob River and Yenisei River Estuaries to the Kara Sea was studied. The length of both transects was about 700 km. Water depth was 12-63 m, O2 dissolved :5.36-9.55 ml l-1. Along the transects salinity increased from 0.07 to 34.2 psu, while the SPM' concentration decreased from 10.31 to 0.31 mg/l. Total suspended particulate matter load is more than one order of magnitude higher in the Ob River Estuary comparing to that of the Yenisei River. It has led to a significant difference between the suspended trace metals' concentrations (µg/l) in water of the two estuaries. With salinity increase along transects Fe susp., Mn susp. and Zn susp. decreased by a factor of 100-500, that has led to a growth of a relative portion of dissolved trace metals followed by their bioaccumulation (Demina et al., 2010). A strong direct correlation between suspended Cu, Fe and SPM mass concentration was found. For the first time along the Yenisei River' Estuary -the Kara Sea transect a direct positive correlation between Cu suspended and volume concentration of SPM (mg/ml3) was found, that was attributed to contribution of phytoplankton aggregates in the SPM composition. A trend of relationship between content of suspended As and pelitic fraction (2-10 µm) of SPM was firstly found in theses basins also. Study of trace metal speciation in the bottom sediments (adsorbed, associated with Fe-Mn (oxyhydr)oxides, organic matter and fixed in the mineral lattice or refractory) has revealed the refractory fraction to be prevailing (70-95% total content) for Fe, Zn, Cu, Co, Ni, Cr, Cd and Pb. That means that toxic heavy metals were not available for bottom fauna. Mn was predominantly found in the adsorbed and (oxyhydr)oxides geochemically labile forms, reflecting the redox condition change along both transects and within the sedimentary cores. References. Demina L.L., Gordeev V.V., Galkin S.V., Kravchishina M.D. Biogeochemistry of some heavy metals and metalloids along the transect the Ob River Estuary - the Kara Sea. Oceanology, 2010, vo. 50, No 5, pp. 729- 742.

Monoamine oxidase inhibitory activity in tobacco particulate matter: Are harman and norharman the only physiologically relevant inhibitors?

PubMed

Truman, Penelope; Grounds, Peter; Brennan, Katharine A

2017-03-01

Monoamine oxidase inhibition is significant in smokers, but it is still unclear how the inhibition that is seen in the brains and bodies of smokers is brought about. Our aim was to test the contribution of the harman and norharman in tobacco smoke to MAO-A inhibition from tobacco smoke preparations, as part of a re-examination of harman and norharman as the cause of the inhibition of MAO-A inhibition in the brain. Tobacco smoke particulate matter and cigarette smoke particulate matter were prepared and the amounts of harman and norharman measured. The results were compared with the total monoamine oxidase-A inhibitory activity. At a nicotine concentration of 0.6μM (a "physiological" concentration in blood) the total monoamine oxidase-A inhibitory activity measured in these samples was sufficient to inhibit the enzyme by approximately 10%. Of this inhibitory activity, only a small proportion of the total was found to be due to harman and norharman. These results show that harman and norharman provide only a moderate contribution to the total monoamine oxidase-A inhibitory activity of tobacco smoke, perhaps under 10%. This suggests that other inhibitors (either known or unknown) may be more significant contributors to total inhibitory activity than has yet been established, and deserve closer examination. Copyright © 2017 Elsevier B.V. All rights reserved.

Smelting Magnesium Metal using a Microwave Pidgeon Method

PubMed Central

Wada, Yuji; Fujii, Satoshi; Suzuki, Eiichi; Maitani, Masato M.; Tsubaki, Shuntaro; Chonan, Satoshi; Fukui, Miho; Inazu, Naomi

2017-01-01

Magnesium (Mg) is a lightweight metal with applications in transportation and sustainable battery technologies, but its current production through ore reduction using the conventional Pidgeon process emits large amounts of CO2 and particulate matter (PM2.5). In this work, a novel Pidgeon process driven by microwaves has been developed to produce Mg metal with less energy consumption and no direct CO2 emission. An antenna structure consisting of dolomite as the Mg source and a ferrosilicon antenna as the reducing material was used to confine microwave energy emitted from a magnetron installed in a microwave oven to produce a practical amount of pure Mg metal. This microwave Pidgeon process with an antenna configuration made it possible to produce Mg with an energy consumption of 58.6 GJ/t, corresponding to a 68.6% reduction when compared to the conventional method. PMID:28401910

Seasonal plankton variability in Chilean Patagonia fjords: Carbon flow through the pelagic food web of Aysen Fjord and plankton dynamics in the Moraleda Channel basin

NASA Astrophysics Data System (ADS)

González, H. E.; Castro, L.; Daneri, G.; Iriarte, J. L.; Silva, N.; Vargas, C. A.; Giesecke, R.; Sánchez, N.

2011-03-01

Two research cruises ( CIMAR 13 Fiordos) were conducted in the N-S oriented macrobasin of the Moraleda Channel (42-47°S), which includes the E-W oriented Puyuhuapi Channel and Aysen Fjord, during two contrasting productive seasons: austral winter (27 July-7 August 2007) and spring (2-12 November 2007). These campaigns set out to assess the spatio-temporal variability, defined by the local topography along Moraleda Channel, in the biological, physical, and chemical oceanographic characteristics of different microbasins and to quantify the carbon budget of the pelagic trophic webs of Aysen Fjord. Seasonal carbon fluxes and fjord-system functioning vary widely in our study area. In terms of spatial topography, two constriction sills (Meninea and Elefantes) define three microbasins along Moraleda Channel, herein the (1) north (Guafo-Meninea), (2) central (Meninea-Elefantes), and (3) south (Elefantes-San Rafael Lagoon) microbasins. In winter, nutrient concentrations were high (i.e. nitrate range: 21-14 μM) and primary production was low (153-310 mgC m -2 d -1), suggesting that reduced light radiation depressed the plankton dynamics throughout Moraleda Channel. In spring, primary production followed a conspicuous N-S gradient, which was the highest (5167 mgC m -2 d -1) in the north microbasin and the lowest (742 mgC m -2 d -1) in the south microbasin. The seasonal pattern of the semi-enclosed Puyuhuapi Channel and Aysen Fjord, however, revealed no significant differences in primary production (˜800 mgC m -2 d -1), and vertical fluxes of particulate organic carbon were nearly twice as high in spring as in winter (266 vs. 168 mgC m -2 d -1). At the time-series station (St. 79), the lithogenic fraction dominated the total sedimented matter (seston). The role of euphausiids in the biological carbon pump of the Patagonian fjords was evident, given the predominance of zooplankton fecal material, mostly euphausiid fecal strings (46% of all fecal material), among the recognizable particles contributing to the particulate organic carbon flux. The topographic constriction sills partially modulated the exchange of oceanic waters (Subantarctic Surface Water) with freshwater river discharges along the Moraleda Channel. This exchange affects salinity and nutrient availability and, thus, the plankton structure. The north microbasin was dominated by a seasonal alternation of the classical (spring) and microbial (winter) food webs. However, in the south microbasin, productivity was low and the system was dominated year-round by large inputs of glacier-derived, silt-rich freshwater carrying predominantly small-sized diatoms ( Skeletonema spp) and bacteria. When superimposed upon this scenario, highly variable (seasonal) solar radiation and photoperiods could exacerbate north-south differences along Moraleda Channel.

Including impacts of particulate emissions on marine ecosystems in life cycle assessment: the case of offshore oil and gas production.

PubMed

Veltman, Karin; Huijbregts, Mark A J; Rye, Henrik; Hertwich, Edgar G

2011-10-01

Life cycle assessment is increasingly used to assess the environmental performance of fossil energy systems. Two of the dominant emissions of offshore oil and gas production to the marine environment are the discharge of produced water and drilling waste. Although environmental impacts of produced water are predominantly due to chemical stressors, a major concern regarding drilling waste discharge is the potential physical impact due to particles. At present, impact indicators for particulate emissions are not yet available in life cycle assessment. Here, we develop characterization factors for 2 distinct impacts of particulate emissions: an increased turbidity zone in the water column and physical burial of benthic communities. The characterization factor for turbidity is developed analogous to characterization factors for toxic impacts, and ranges from 1.4 PAF (potentially affected fraction) · m(3) /d/kg(p) (kilogram particulate) to 7.0 x 10³ [corrected] for drilling mud particles discharged from the rig. The characterization factor for burial describes the volume of sediment that is impacted by particle deposition on the seafloor and equals 2.0 × 10(-1) PAF · m(3) /d/kg(p) for cutting particles. This characterization factor is quantified on the basis of initial deposition layer characteristics, such as height and surface area, the initial benthic response, and the recovery rate. We assessed the relevance of including particulate emissions in an impact assessment of offshore oil and gas production. Accordingly, the total impact on the water column and on the sediment was quantified based on emission data of produced water and drilling waste for all oil and gas fields on the Norwegian continental shelf in 2008. Our results show that cutting particles contribute substantially to the total impact of offshore oil and gas production on marine sediments, with a relative contribution of 55% and 31% on the regional and global scale, respectively. In contrast, the contribution of particulate emissions to the total impact on the marine water column is of minor importance. We conclude that particles are an important stressor in marine ecosystems, particularly for marine sediment, and particulate emissions should therefore be included in a (life cycle) impact assessment of offshore oil and gas production. Copyright © 2011 SETAC.

Escherichia coli attachment to model particulates: The effects of bacterial cell characteristics and particulate properties.

PubMed

Liang, Xiao; Liao, Chunyu; Soupir, Michelle L; Jarboe, Laura R; Thompson, Michael L; Dixon, Philip M

2017-01-01

E. coli bacteria move in streams freely in a planktonic state or attached to suspended particulates. Attachment is a dynamic process, and the fraction of attached microorganisms is thought to be affected by both bacterial characteristics and particulate properties. In this study, we investigated how the properties of cell surfaces and stream particulates influence attachment. Attachment assays were conducted for 77 E. coli strains and three model particulates (ferrihydrite, Ca-montmorillonite, or corn stover) under environmentally relevant conditions. Surface area, particle size distribution, and total carbon content were determined for each type of particulate. Among the three particulates, attachment fractions to corn stover were significantly larger than the attachments to 2-line ferrihydrite (p-value = 0.0036) and Ca-montmorillonite (p-value = 0.022). Furthermore, attachment to Ca-montmorillonite and corn stover was successfully modeled by a Generalized Additive Model (GAM) using cell characteristics as predictor variables. The natural logarithm of the net charge on the bacterial surface had a significant, positive, and linear impact on the attachment of E. coli bacteria to Ca-montmorillonite (p-value = 0.013), but it did not significantly impact the attachment to corn stover (p-value = 0.36). The large diversities in cell characteristics among 77 E. coli strains, particulate properties, and attachment fractions clearly demonstrated the inadequacy of using a static parameter or linear coefficient to predict the attachment behavior of E. coli in stream water quality models.

Dissolved and particulate organic carbon in the melt water of Icelandic glaciers

NASA Astrophysics Data System (ADS)

Chifflard, Peter; Reiss, Martin

2017-04-01

Recently, glaciers have been recognized as unique ecosystems with potential effects on the global carbon cycle. Among other transport processes organic carbon stored in glacier ecosystems is released from the glaciers through melt at the glaciers surface that discharges into proglacial streams and finally into the ocean. Nevertheless, the potential role of glaciers in the carbon cycle remains poorly understood (Hood et al. 2015). One particular problem in this respect is that there is a lack in regional and global analysis of the total amount of organic carbon released from glaciers. Although, the release of organic carbon has been investigated in proglacial streams in Alaska, the European Alps and Greenland, to our knowledge, there is no information available for Icelandic proglacial streams. Thus, the aims of this study are: 1) to develop a first base information about the concentration of dissolved and particulate organic carbon (DOC and POC) in several Icelandic proglacial streams and 2) to detect the variability of DOC and POC along a proglacial stream from the glacier source to the mouth into the Atlantic Ocean. Therefore, a field trip was conducted between 23 and 31 July 2016, whereby, 25 water samples were taken. The sampling points cover melt water from the following Icelandic glaciers Vatnajökull, Langjökull, Hofsjökull, Myrdalsjökull and Tungnafellsjökull. Further water samples were taken along the river Hvitá starting at the glacier Langjökull and ending at the mouth into the Atlantic ocean in the southwest of Iceland. At every sample point electrical conductivity, water temperate and the pH-value were measured in situ using a calibrated portable water quality meter (Hanna Combo HI98129). The water samples (130 ml) were filtered using pre-combusted GF/F filters (Whatman, pore sizes 0.7 µm) and stored in a cooling box until the shipment to the laboratory of the Department for Geography, Philipps-University of Marburg. The DOC concentrations in the filtered water samples were measured using a TOC analyzer using high-temperature combustion of organic matter (OM) followed by thermal detection of CO2 (TOC-L, Shimadzu, Japan). POC was measured by determining mass lost upon combustion of the samples. Therefore all glass fiber membranes were dried after sampling at 65°C to a constant weight, reweighed to calculate the total suspended solids (TSS), combusted via heating the filter to 550° C and finally reweighed to calculate the amount of particulate organic matter. Spectroscopic characteristics were detected by using a spectrophotometer (ThermoFisher, Genesys 10S) for UV-VIS analysis and a fluorescence spectrometer (Shimadzu RF-6000) for fluorescence analysis. Spectroscopic indices will be calculated based on these UV-VIS and fluorescence data. First results show that the DOC-concentrations are very low and range from 0.113 mg/l to 0.937 mg/l. These concentrations are comparable with values measured in the melt water in other regions (Alaska, Greenland and European Alps) (Hood et al. 2015). POC concentrations range from 0.667 mg/l to 173.333 mg/l and exceed the DOC-concentration at every sampling location. This differences can be compared with results of the Greenland Ice Sheet, but not with some small glaciers in the European Alps, where the concentrations of DOC and POC more or less equal (Hood et al. 2015). Nevertheless, the export of POC plays a very important factor within the organic carbon export budget of glaciers in Iceland and further measurements are required. Hood, E., Battin, T. J., Fellman, J., O'Neel, S., & Spencer, R. G. (2015). Storage and release of organic carbon from glaciers and ice sheets. Nature Geoscience, 8(2), 91-96.

The Spatial-temperal Distribution of Phosphorus Species and the Main Factors Influencing on Phosphorus Transportation in Middle Reaches of the Yarlung Zangbo River, China

NASA Astrophysics Data System (ADS)

Pu, X.; An, R.; Li, R.; Huang, W.; Li, J.

2017-12-01

The objectives of the current study are to investigate the spatial, temperal variation of phisphorus (P) fraction in middle reaches of the Yarlung Zangbo River of China. Samples were collected in April (dry season), August (wet season), and Octber (normal season) along with the middle reaches from Lazi site to Nuxia sitewhich which is about 1000km long. Sequential extraction were applied to determine the forms of phosphorus in suspended particles and to assess the potential bioavailability of particulate P. The results indicated that the distribution of suspended particle size inflenced not only the total phosphorus concentration, but also the proportions of different forms of phosphorus. The exchangeable phosphorus (Ex-P), Fe-bound-P, Ca-bound-P were the most aboundant forms and the highest proportions of total P. The total P concentrations were closely relative to the concentration of suspended particles. According to the characteristics of suspended particles in the Yarlung Zangbo River, the relationship between the suspended particles size and species of phosphorus was established though statistical analysis. The Ex-P increased with the decreasing of suspended particulate size. The content of bioavailable particulate phosphorus varied greatly with the proportions of particulate size. In genral, the higher the proportion of smaller particle size, the higher the content of bioavailable phosphorus. The main factors which affect the phosphorus transportation in Yarlung Zangbo River had also been discussed.

Effects of simulated deposition of acid mist and iron ore particulate matter on photosynthesis and the generation of oxidative stress in Schinus terebinthifolius Radii and Sophora tomentosa L.

PubMed

Kuki, Kacilda Naomi; Oliva, Marco Antônio; Pereira, Eduardo Gusmão; Costa, Alan Carlos; Cambraia, José

2008-09-15

Particulate matter is a natural occurrence in the environment, but some industries, such as the iron ore sector, can raise the total amount of particles in the atmosphere. This industry is primarily a source of iron and sulfur dioxide particulates. The effects of the pollutants from the iron ore industries on representatives of restinga vegetation in a Brazilian coastal ecosystem were investigated using physiological and biochemical measures. Two species, Schinus terebinthifolius and Sophora tomentosa, were exposed to simulated deposition of acid mist and iron ore particulate matter in acrylic chambers in a greenhouse. Parameters such as gas exchange, fluorescence emission, chlorophyll content, total iron content, antioxidant enzyme activity and malondialdehyde content were assessed in order to evaluate the responses of the two species. Neither treatment was capable of inducing oxidative stress in S. terebinthifolius. Nevertheless, the deposition of iron ore particulates on this species increased chlorophyll content, the maximum quantum efficiency of photosystem II and the electron transport rate, while iron content was unaltered. On the other hand, S. tomentosa showed a greater sensitivity to the treatments. Plants of S. tomentosa that were exposed to acid mist had a decrease in photosynthesis, while the deposition of iron particulate matter led to an increase in iron content and membrane permeability of the leaves. The activities of antioxidant enzymes, such as catalases and superoxide dismutase, were enhanced by both treatments. The results suggested that the two restinga species use different strategies to overcome the stressful conditions created by the deposition of particulate matter, either solid or wet. It seems that while S. terebinthifolius avoided stress, S. tomentosa used antioxidant enzyme systems to partially neutralize oxidative stress. The findings also point to the potential use of S. tomentosa as a biomarker species under field conditions.

Subchronic inhalation of coal dust particulate matter 10 induces bronchoalveolar hyperplasia and decreases MUC5AC expression in male Wistar rats.

PubMed

Kania, Nia; Setiawan, Bambang; Widjadjanto, Edi; Nurdiana, Nurdiana; Widodo, M Aris; Kusuma, H M S Chandra

2014-10-01

Coal dust is a pollutant found in coal mines that are capable of inducing oxidative stress and inflammation, but the effects on lung metaplasia as an early step of carcinogenesis remain unknown. The purpose of the present study was to evaluate the effects of PM10 coal dust on lung histology, MUC5AC expression, epidermal growth factor (EGF) expression, and epidermal growth factor receptor (EGFR) expression. An experimental study was done on male Wistar rats, which were divided into the following groups: control groups exposed to coal dust for 14 days (at doses of 6.25 mg/m(3), 12.5 mg/m(3), and 25 mg/m(3)), and the groups exposed to coal dust for 28 days (at doses of 6.25 mg/m(3), 12.5 mg/m(3), and 25 mg/m(3)). EGF expressions in rat lungs were measured by ELISA. EGFR and MUC5AC were measured by a confocal laser scanning microscope. The bronchoalveolar epithelial image of the group exposed to coal dust for 14 and 28 days showed a epithelial rearrangement, hyperplastic (metaplastic) goblet cells, and scattered massive inflammatory cells. The pulmonary parenchymal image of the group of exposed to coal dust for 14 and 28 days showed scattered inflammatory cells filling up the pulmonary alveolar networks, leading to an appearance of thickened parenchymal alveoli until emphysema-like structure. There was no significant difference in MUC5AC, EGF, and EGFR expressions for 14-d exposure (p>0.05). There was no significant difference in EGF and EGFR expressions for 28-d exposure (p>0.05), but there was a significant difference in MUC5AC expression (p<0.05). We concluded that subchronic inhalation of coal dust particulate matter 10 induces bronchoalveolar reactive hyperplasia and rearrangement of epithelial cells which accompanied by decrease expression MUC5AC in male rats. Copyright © 2014 Elsevier GmbH. All rights reserved.

Thermal infrared emission spectroscopy of the pyroxene mineral series

NASA Astrophysics Data System (ADS)

Hamilton, Victoria E.

2000-04-01

The thermal infrared emissivity spectra of coarse particulate samples of compositions in the pyroxene series display reststrahlen features (absorptions) that distinguish not only orthorhombic from monoclinic structures, but also major end-members within the two structural groups, as well as minerals within solid solution series. The exact number of reststrahlen features observed and their positions are dependent on mineral structure and cation occupancy of the M1 and M2 sites. End-member quadrilateral pyroxenes (Mg2Si2O6-Fe2Si2O6-Ca[Mg,Fe]Si2O6) are easily distinguished from each other and from minerals in the nonquadrilateral series (NaFeSi2O6-Na[Al,Fe]Si2O6-LiAlSi2O6). Furthermore, among quadrilateral pyroxenes, variations in Mg/(Mg+Fe) are linearly correlated with several band locations, as are variations in Ca content in high-Ca clinopyroxenes. In both quadrilateral and nonquadrilateral compositions, Christiansen feature positions are also diagnostic. No correlations with minor constituents (of the order of 0.05 atoms per formula unit) were observed. The detailed spectral characteristics of pyroxenes and their variability as a function of structure and cation occupancy are presented here with determinative curves for the identification of pyroxene composition. These data have important implications for the interpretation of spectral data from both laboratory and remote sensing instruments because they should permit a more detailed determination of pyroxene composition in measured unknown pure mineral and bulk compositions dominated by surface scattering, i.e., all particulates greater than ~65 μm, and solid samples.

Characteristics and source appointment of atmospheric particulate mercury over East China Sea: Implication on the deposition of atmospheric particulate mercury in marine environment.

PubMed

Duan, Lian; Cheng, Na; Xiu, Guangli; Wang, Fujiang; Chen, Ying

2017-05-01

Total Suspended Particulate (TSP) samples were collected at Huaniao Island in northern East China Sea (ECS) from March 2012 to January 2013. Chemical analysis were conducted to measure the concentration of total particulate mercury (TPM) and speciated particulate mercury including HCl-soluble particulate mercury (HPM), elemental particulate mercury (EPM) and residual particulate mercury (RPM). The bromine (Br) and iodine (I) on particles were also detected. The mean concentration of TPM during the study period was 0.23 ± 0.15 ng m -3 , while the obviously seasonal variation was found that the concentrations of TPM in spring, summer, fall and winter were 0.34 ± 0.20 ng m -3 , 0.15 ± 0.03 ng m -3 , 0.15 ± 0.05 ng m -3 and 0.27 ± 0.26 ng m -3 , respectively. The statistically strong correlation of bromine and iodine to HPM was only found in spring with r = 0.81 and 0.77 (p < 0.01), respectively. While the strongest correlations between EPM and bromine and iodine were found in winter with r = 0.92 (Br) and 0.96 (I) (p < 0.01), respectively. The clustered 72-h backward trajectories of different seasons and the whole sampling period were categorized into 4 groups. In spring, the clusters passed a long distance across the East China Sea and brought about low concentration of mercury due to the deposition of mercury over the sea. The cluster of air mass across the sea had low concentration of HPM in winter, which suggested that the oxidation of mercury in winter might be related to other oxidants. During the whole sampling period, the air mass from the north of China contributed to the higher concentration of TPM in Huaniao Island. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessment of historical exposures in a nickel refinery in Norway.

PubMed

Grimsrud, T K; Berge, S R; Resmann, F; Norseth, T; Andersen, A

2000-08-01

The aim of the study was, on the basis of new information on nickel species and exposure levels, to generate a specific exposure matrix for epidemiologic analyses in a cohort of Norwegian nickel-refinery workers with a known excess of respiratory cancer. A department-time-exposure matrix was constructed with average exposure to total nickel estimated as the arithmetic mean of personal measurements for periods between 1973 and 1994. From 1972 back to the start of production in 1910, exposure concentrations were estimated through retrograde calculation with multiplication factors developed on the basis of reported changes in the metallurgical process and work environment. The relative distribution of water-soluble nickel salts (sulfates and chlorides), metallic nickel, and particulates with limited solubility (sulfides and oxides) was mainly derived from speciation analyses conducted in the 1990s. The average concentration of nickel in the breathing zone was < or = 0.7 mg/m3 for all workers after 1978. Exposure levels for smelter and roaster day workers were 2-6 mg/m3 before 1970, while workers in nickel electrolysis and electrolyte purification were exposed to concentrations in the range of 0.15-1.2 mg/m3. The level of water-soluble nickel was of the same order for workers in the smelting and roasting departments as in some of the electrolyte purification departments. Compared with earlier estimates, the present matrix probably offers a more reliable description of past exposures at the plant.

Water-quality conditions in the New River, Imperial County, California

USGS Publications Warehouse

Setmire, James G.

1979-01-01

The New River, when entering the United States at Calexico, Calif., often contains materials which have the appearance of industrial and domestic wastes. Passage of some of these materials is recognized by a sudden increase in turbidity over background levels and the presence of white particulate matter. Water samples taken during these events are usually extremely high in organic content. During a 4-day reconnaissance of water quality in May 1977, white-to-brown extremely turbid water crossed the border on three occasions. On one of these occasions , the water was intensively sampled. The total organic-carbon concentration ranged from 80 to 161 milligrams per liter (mg/l); dissolved organic carbon ranged from 34 to 42 mg/l, and the chemical oxygen demand was as high as 510 mg/l. River profiles showed a dissolved-oxygen sag, with the length of the zone of depressed dissolved-oxygen concentrations varying seasonally. During the summer months, dissolved-oxygen concentrations in the river were lower and the zone of depressed dissolved-oxygen concentrations was longer. The largest increases in dissolved-oxygen concentration from reaeration occurred at the three drop structures and the rock weir near Seeley. The effects of oxygen demanding materials crossing the border extended as far as Highway 80, 19.5 miles downstream from the international boundary at Calexico. Fish kills and anaerobic conditions were also detected as far as Highway 80. Standard bacteria indicator tests for fecal contamination showed a very high health-hazard potential near the border. (Woodard-USGS)

What Do Middle and High School Students Know about the Particulate Nature of Matter after Instruction? Implications for Practice

ERIC Educational Resources Information Center

Aydeniz, Mehmet; Kotowski, Erin Leigh

2012-01-01

This study explores middle and high school students' understanding of the particulate nature of matter after they were taught the concept. A total of 87 students (41 high school and 46 middle school) participated in the study. Findings suggest that students held misconceptions about the law of conservation of matter, chemical composition of matter…

Mercury in Indiana watersheds: retrospective for 2001-2006

USGS Publications Warehouse

Risch, Martin R.; Baker, Nancy T.; Fowler, Kathleen K.; Egler, Amanda L.; Lampe, David C.

2010-01-01

Information about total mercury and methylmercury concentrations in water samples and mercury concentrations in fish-tissue samples was summarized for 26 watersheds in Indiana that drain most of the land area of the State. Mercury levels were interpreted with information on streamflow, atmospheric mercury deposition, mercury emissions to the atmosphere, mercury in wastewater, and landscape characteristics. Unfiltered total mercury concentrations in 411 water samples from streams in the 26 watersheds had a median of 2.32 nanograms per liter (ng/L) and a maximum of 28.2 ng/L. When these concentrations were compared to Indiana water-quality criteria for mercury, 5.4 percent exceeded the 12-ng/L chronic-aquatic criterion, 59 percent exceeded the 1.8-ng/L Great Lakes human-health criterion, and 72.5 percent exceeded the 1.3-ng/L Great Lakes wildlife criterion. Mercury concentrations in water were related to streamflow, and the highest mercury concentrations were associated with the highest streamflows. On average, 67 percent of total mercury in streams was in a particulate form, and particulate mercury concentrations were significantly lower downstream from dams than at monitoring stations not affected by dams. Methylmercury is the organic fraction of total mercury and is the form of mercury that accumulates and magnifies in food chains. It is made from inorganic mercury by natural processes under specific conditions. Unfiltered methylmercury concentrations in 411 water samples had a median of 0.10 ng/L and a maximum of 0.66 ng/L. Methylmercury was a median 3.7 percent and maximum 64.8 percent of the total mercury in 252 samples for which methylmercury was reported. The percentages of methylmercury in water samples were significantly higher downstream from dams than at other monitoring stations. Nearly all of the total mercury detected in fish tissue was assumed to be methylmercury. Fish-tissue samples from the 26 watersheds had wet-weight mercury concentrations that exceeded the 0.3 milligram per kilogram (mg/kg) U.S. Environmental Protection Agency (USEPA) methylmercury criterion in 12.4 percent of the 1,731 samples. The median wet-weight concentration in the fish-tissue samples was 0.13 mg/kg, and the maximum was 1.07 mg/kg. A coarse-scale analysis of all fish-tissue data in each watershed and a fine-scale analysis of data within 5 kilometers (km) of the downstream end of each watershed showed similar results overall. Mercury concentrations in fish-tissue samples were highest in the White River watershed in southern Indiana and the Fall Creek watershed in central Indiana. In fish-tissue samples within 5 km of the downstream end of a watershed, the USEPA methylmercury criterion was exceeded by 45 percent of mercury concentrations from the White River watershed and 40 percent of the mercury concentration from the Fall Creek watershed. A clear relation between mercury concentrations in fish-tissue samples and methylmercury concentrations in water was not observed in the data from watersheds in Indiana. Average annual atmospheric mercury wet-deposition rates were mapped with data at 156 locations in Indiana and four surrounding states for 2001-2006. These maps revealed an area in southeastern Indiana with high mercury wet-deposition rates-from 15 to 19 micrograms per square meter per year (ug/m2/yr). Annual atmospheric mercury dry-deposition rates were estimated with an inferential method by using concentrations of mercury species in air samples at three locations in Indiana. Mercury dry deposition-rates were 5.6 to 13.6 ug/m2/yr and were 0.49 to 1.4 times mercury wet-deposition rates. Total mercury concentrations were detected in 96 percent of 402 samples of wastewater effluent from 50 publicly owned treatment works in the watersheds; the median concentration was 3.0 ng/L, and the maximum was 88 ng/L. When these concentrations were compared to Indiana water-quality criteria for mercury, 12 percent exceeded the 12-n

Concentrations and patterns of polychlorinated biphenyls at different process stages of cement kilns co-processing waste incinerator fly ash.

PubMed

Liu, Guorui; Yang, Lili; Zhan, Jiayu; Zheng, Minghui; Li, Li; Jin, Rong; Zhao, Yuyang; Wang, Mei

2016-12-01

Cement kilns can be used to co-process fly ash from municipal solid waste incinerators. However, this might increase emission of organic pollutants like polychlorinated biphenyls (PCBs). Knowledge of PCB concentrations and homolog and congener patterns at different stages in this process could be used to assess the possibility of simultaneously controlling emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and "dioxin-like" compounds. To date, emissions from cement kilns co-processing fly ash from municipal solid waste incinerators have not been analyzed for PCBs. In this study, stack gas and particulate samples from two cement kilns co-processing waste incinerator fly ash were analyzed for PCBs. The average total tri- to deca-chlorinated biphenyl (∑ 3-10 PCB) concentration in the stack gas samples was 10.15ngm -3 . The ∑ 3-10 PCB concentration ranges in particulate samples from different stages were 0.83-41.79ngg -1 for cement kiln 1and0.13-1.69ngg -1 for cement kiln 2. The ∑ 3-10 PCB concentrations were much higher in particulate samples from the suspension pre-heater boiler, humidifier tower, and kiln back-end bag filters than in particulate samples from other stages. For these three stages, PCBs contributed to 15-18% of the total PCB, PCDD/F, and polychlorinated naphthalene toxic equivalents in stack gases and particulate matter. The PCB distributions were similar to those found in other studies for PCDD/Fs and polychlorinated naphthalenes, which suggest that it may be possible to simultaneously control emissions of multiple organic pollutants from cement kilns. Homolog patterns in the particulate samples were dominated by the pentachlorobiphenyls. CB-105, CB-118, and CB-123 were the dominant dioxin-like PCB congeners that formed at the back-end of the cement kiln. A mass balance of PCBs in the cement kilns indicated that the total mass of PCBs in the stack gases and clinker was about half the mass of PCBs in the raw materials. Copyright © 2016 Elsevier Ltd. All rights reserved.

Parameters for the Operation of Bacterial Thiosalt Oxidation Ponds

PubMed Central

Silver, M.

1985-01-01

Shake flask and pH-controlled reactor tests were used to determine the mathematical parameters for a mixed-culture bacterial thiosalt treatment pond. Values determined were as follows: Km and Vmax (thiosulfate), 9.83 g/liter and 243.9 mg/liter per h, respectively; Ki (lead), 3.17 mg/liter; Ki (copper), 1.27 mg/liter; Q10 between 10 and 30°C, 1.95. From these parameters, the required bioxidation pond volume and residence time could be calculated. Soluble zinc (0.2 g/liter) and particulate mill products and by-products (0.25 g/liter) were not inhibitory. Correlation with an operating thiosalt biooxidation pond showed the parameters used to be valid for thiosalt concentrations up to at least 2 g/liter, lead concentrations of at least 10 mg/liter, and temperatures of >2°C. PMID:16346885

Formation of Particulate Matter during Wintertime Inversions in the Salt Lake Valley.

NASA Astrophysics Data System (ADS)

Hrdina, A. I. H.; Baasandorj, M.; Lin, J. C.; Murphy, J. G.; McKeen, S. A.

2017-12-01

In the wintertime, the air quality in Salt Lake City is frequently impacted by inversions that cause high levels of particulate matter. An inversion describes a highly stable air mass, where a cold air pool (CAP) is trapped by warmer air aloft. In the right conditions, these CAPs can persist for several days allowing the accumulation of various pollutants, such as NOx and NH3, leading to secondary particle formation. Concentrations of reactive trace gases (HCl, HNO3, HONO, NH3, SO2) and particle phase constituents (Cl-, NO2-, NO3-, SO42-, Na+, NH4+, K+, Mg2+, Ca2+) from particles less than 2.5 microns in diameter (PM2.5) were continuously measured using an online ambient ion monitor ion chromatograph (AIM-IC) within the Salt Lake Valley, Utah, from Jan 17 - Feb 21 2017, as part of the Utah Fine Particulate Study (UWFPS 2017). A consistent diurnal pattern of ammonia mixing ratios was observed, with mixing ratios ranging from 0.1 - 7 ppb. Two persistent cold air pool events occurred during the measurement period during which the suppression of vertical mixing led to the buildup of PM2.5 in the valley. The total PM2.5 level in the valley was as high as 60 μg m-3 and was dominated by ammonium nitrate. The air pollution transport within the valley during the entire campaign period was examined using Stochastic Time-Inverted Lagrangian Transport (STILT) model. Calculated flux footprints, based on back-trajectories with 15 minute time steps at a grid resolution of 0.1 degree, highlight the potential source regions for PM2.5 precursors during the observed PCAP events. Observations were also compared to output from the Weather Research and Forecasting model coupled with chemistry (WRF-Chem) simulations of the UWFPS campaign.

Decadal-scale export of nitrogen, phosphorus, and sediment from the Susquehanna River basin, USA: Analysis and synthesis of temporal and spatial patterns.

PubMed

Zhang, Qian; Ball, William P; Moyer, Douglas L

2016-09-01

The export of nitrogen (N), phosphorus (P), and suspended sediment (SS) is a long-standing management concern for the Chesapeake Bay watershed, USA. Here we present a comprehensive evaluation of nutrient and sediment loads over the last three decades at multiple locations in the Susquehanna River basin (SRB), Chesapeake's largest tributary watershed. Sediment and nutrient riverine loadings, including both dissolved and particulate fractions, have generally declined at all sites upstream of Conowingo Dam (non-tidal SRB outlet). Period-of-record declines in riverine yield are generally smaller than those in source input, suggesting the possibility of legacy contributions. Consistent with other watershed studies, these results reinforce the importance of considering lag time between the implementation of management actions and achievement of river quality improvement. Whereas flow-normalized loadings for particulate species have increased recently below Conowingo Reservoir, those for upstream sites have declined, thus substantiating conclusions from prior studies about decreased reservoir trapping efficiency. In regard to streamflow effects, statistically significant log-linear relationships between annual streamflow and annual constituent load suggest the dominance of hydrological control on the inter-annual variability of constituent export. Concentration-discharge relationships revealed general chemostasis and mobilization effects for dissolved and particulate species, respectively, both suggesting transport-limitation conditions. In addition to affecting annual export rates, streamflow has also modulated the relative importance of dissolved and particulate fractions, as reflected by its negative correlations with dissolved P/total P, dissolved N/total N, particulate P/SS, and total N/total P ratios. For land-use effects, period-of-record median annual yields of N, P, and SS all correlate positively with the area fraction of non-forested land but negatively with that of forested land under all hydrological conditions. Overall, this work has informed understanding with respect to four major factors affecting constituent export (i.e., source input, reservoir modulation, streamflow, and land use) and demonstrated the value of long-term river monitoring. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Statistical summary and trend evaluation of air quality data for Cleveland, Ohio in 1967 to 1971: Total suspended particulate, nitrogen dioxide, and sulfur dioxide

NASA Technical Reports Server (NTRS)

Neustadter, H. E.; Sidik, S. M.; Burr, J. C., Jr.

1972-01-01

Air quality data for Cleveland, Ohio, for the period of 1967 to 1971 were collated and subjected to statistical analysis. The total suspended particulate component is lognormally distributed; while sulfur dioxide and nitrogen dioxide are reasonably approximated by lognormal distributions. Only sulfur dioxide, in some residential neighborhoods, meets Ohio air quality standards. Air quality has definitely improved in the industrial valley, while in the rest of the city, only sulfur dioxide has shown consistent improvement. A pollution index is introduced which displays directly the degree to which the environmental air conforms to mandated standards.

Statistical summary of air quality data for metropolitian Cleveland, Ohio, 1967 - 1972: Total suspended particulates, nitrogen dioxide, and sulfur dioxide

NASA Technical Reports Server (NTRS)

King, R. B.; Neustadter, H. E.; Fordyce, J. S.; Burr, J. C., Jr.; Cornett, C. L.

1974-01-01

Air-quality data for metropolitan Cleveland, Ohio, from 1967 through 1972 were collated and statistically analyzed. Total suspended particulates (TSP) departed from lognormal distribution in 1972. Nitrogen dioxide and sulfur dioxide, departed significantly from lognormal distributions in 1972. In Cleveland the Ohio standards were not met. However, the data indicate a general improvement in air quality. Unusually high precipitation (43% above the average in 1972) may be responsible in lowering these values from the 1971 levels. The mean values of TSP, NO2, and SO2 are 104, 191, and 83 microgram/cu m respectively.

Transformation of metals speciation in a combined landfill leachate treatment.

PubMed

Wu, Yanyu; Zhou, Shaoqi; Chen, Dongyu; Zhao, Rong; Li, Huosheng; Lin, Yiming

2011-04-01

Landfill leachate was treated by a combined sequential batch reactor (SBR), coagulation, Fenton oxidation and biological aerated filter (BAF) technology. The metals in treatment process were fractionated into three fractions: particulate and colloidal (size charge filtration), free ion/labile (cation exchange) and non-labile fractions. Fifty percent to 66% Cu, Ni, Zn, Mn, Pb and Cd were present as particulate/colloidal matter in raw leachate, whereas Cr was present 94.9% as non-labile complexes. The free ion/labile fractions of Ni, Zn, Mg, Mn, Pb and Cd increased significantly after treatment except Cr. Fifty-nine percent to 100% of Al was present mainly as particulate/colloidal matter >0.45 μm and the remaining portions were predicted as non-labile complexes except in coagulation effluent. The speciation of Fe varied significantly in various individual processes. Visual MINTEQ simulation showed that 95-100% colloidal species for Cu, Cd and Pb were present as metal-humic complexes even with the lower dissolved organic carbon. Optimum agreements for the free ion/labile species were within acidic solution, whereas under-estimated in alkaline effluents. Overestimated particulate/colloidal fraction consisted with the hypothesis that a portion of colloids in fraction <0.45 μm were considered as dissolved. Copyright © 2011 Elsevier B.V. All rights reserved.

Effect of flood events on transport of suspended sediments, organic matter and particulate metals in a forest watershed in the Basque Country (Northern Spain).

PubMed

Peraza-Castro, M; Sauvage, S; Sánchez-Pérez, J M; Ruiz-Romera, E

2016-11-01

An understanding of the processes controlling sediment, organic matter and metal export is critical to assessing and anticipating risk situations in water systems. Concentrations of suspended particulate matter (SPM), dissolved (DOC) and particulate (POC) organic carbon and metals (Cu, Ni, Pb, Cr, Zn, Mn, Fe) in dissolved and particulate phases were monitored in a forest watershed in the Basque Country (Northern Spain) (31.5km(2)) over three hydrological years (2009-2012), to evaluate the effect of flood events on the transport of these materials. Good regression was found between SPM and particulate metal concentration, making it possible to compute the load during the twenty five flood events that occurred during the study period at an annual scale. Particulate metals were exported in the following order: Fe>Mn>Zn>Cr>Pb>Cu>Ni. Annual mean loads of SPM, DOC and POC were estimated at 2267t, 104t and 57t, respectively, and the load (kg) of particulate metals at 76 (Ni), 83 (Cu), 135 (Pb), 256 (Cr), 532 (Zn), 1783 (Mn) and 95170 (Fe). Flood events constituted 91%-SPM, 65%-DOC, 71%-POC, 80%-Cu, 85%-Ni, 72%-Pb, 84%-Cr, 74%-Zn, 87%-Mn and 88%-Fe of total load exported during the three years studied. Flood events were classified into three categories according to their capacity for transporting organic carbon and particulate metals. High intensity flood events are those with high transport capacity of SPM, organic carbon and particulate metals. Most of the SPM, DOC, POC and particulate metal load was exported by this type of flood event, which contributed 59% of SPM, 45% of organic carbon and 54% of metals. Copyright © 2016 Elsevier B.V. All rights reserved.

The weight distribution of coarse particulate organic matter exported from an alpine headwater stream

NASA Astrophysics Data System (ADS)

Turowski, Jens; Badoux, Alexandre; Bunte, Kristin; Rickli, Christian; Federspiel, Nicole

2013-04-01

Coarse particulate organic matter (CPOM) spans sizes from 1 mm particles, weighing less than 1 mg, to large logs and whole trees, which may weigh several hundred kilograms. Different size and weight classes play different roles in stream environments, from being the prime source of energy in stream ecosystems to macroscopically determining channel morphology and local hydraulics. We show that a single scaling exponent can describe the weight distribution of CPOM transported in a mountain stream. This exponent is independent of discharge and valid for particle weights spanning almost seven orders of magnitude. Together with a rating curve of CPOM transport rates with discharge, we discuss the importance of the scaling exponent for measuring strategies, natural hazard mitigation and ecosystems.

Nanoadduct relieves: Alleviation of developmental toxicity of Cr(VI) due to its spontaneous adsorption to Mg(OH)2 nanoflakes.

PubMed

Wang, Zhiping; Li, Chunhui; Mu, Yan; Lin, Zhang; Yi, Anji; Zhang, Qiu; Yan, Bing

2015-04-28

During pregnancy, both the mother and fetus are vulnerable to environmental pollution by particulate matters and chemicals. Although the toxicity of free pollutants has been frequently reported, the impact of nanoparticle/pollutant adducts on the vulnerable pregnant population remains unclear. In this study, pregnant mice were orally exposed to Mg(OH)2 nanoflakes and nanoflakes adsorbed with Cr(VI) anions during the peri-implantation and organogenesis stages of pregnancy at doses that did not induce systemic toxicity or pregnancy complications. The nano-Mg(OH)2/Cr(VI) adducts formation reduced fetal developmental toxicity compared with the toxicity induced by the same concentration of free Cr(VI) anions. Copyright © 2015 Elsevier B.V. All rights reserved.

Killer smog of London, 50 years on: particle properties and oxidative capacity.

PubMed

Whittaker, Andy; BéruBé, Kelly; Jones, Tim; Maynard, Robert; Richards, Roy

2004-12-01

Total suspended particulate (TSP) samples collected on glass fibre filters in London before (1955) and after (1958-1974) the Clean Air Act was examined for physicochemical characteristics and oxidative capacity. High-resolution microscopy identified most of the material as soot with smelter spheres, fly ash (FA), sodium chloride and calcium sulphate particles. Image analysis (IA) was used to show that most of the soot aggregates were less than 1 microm in size and contained chains of individual particles of 10-50 nm. Speed mapping of large agglomerates of the historic particles confirmed that the samples were enriched with soot probably derived from a sulphur-rich coal called nutty slack which was used extensively at this time. Inductively coupled plasma-mass spectrometry (ICP-MS) was used to examine elemental composition. Meaningful quantitation of certain elements (Mg, Al and Zn) proved impossible because they were in high quantities in the glass fibre filters. However, high quantities of Fe>Pb>Cu>Mn>V>As were detected which may explain in part the bioreactivity of the samples. Using a simple in vitro test of oxidative capacity (plasmid assay), one historic particulate sample (1958) showed three times the activity of a modern-day diesel exhaust particle (DEP) sample but ten times less activity than a modern-day urban ambient particle collection. Such studies are continuing to link particle physicochemical properties and bioreactivity with a wider range of the samples collected between 1955 and 74 and how such historic samples compare with present-day London ambient particles.

Atmospheric deposition of polycyclic aromatic hydrocarbons (PAHs) in Shanghai: the spatio-temporal variation and source identification

NASA Astrophysics Data System (ADS)

Cheng, Chen; Bi, Chunjuan; Wang, Dongqi; Yu, Zhongjie; Chen, Zhenlou

2018-03-01

This study investigated the dry and wet deposition fluxes of atmospheric polycyclic aromatic hydrocarbons (PAHs) in Shanghai, China. The flux sources were traced based on composition and spatio-temporal variation. The results show that wet deposition concentrations of PAHs ranged from 0.07 to 0.67 mg·L-1 and were correlated with temperature ( P<0.05). Dry deposition of PAHs concentrations ranged from 3.60-92.15 mg·L-1 and were higher in winter and spring than in summer and autumn. The annual PAH average fluxes were 0.631 mg·m-2·d-1 and 4.06 mg·m-2·d-1 for wet and dry deposition, respectively. The highest wet deposition of PAH fluxes was observed in summer, while dry deposition fluxes were higher in winter and spring. Atmospheric PAHs were deposited as dry deposition in spring and winter, yet wet deposition was the dominant pathway during summer. Total atmospheric PAH fluxes were higher in the northern areas than in the southern areas of Shanghai, and were also observed to be higher in winter and spring. Annual deposition of atmospheric PAHs was about 10.8 t in across all of Shanghai. Wet deposition of PAHs was primarily composed of two, three, or four rings, while dry deposition of PAHs was composed of four, five, or six rings. The atmospheric PAHs, composed of four, five, or six rings, primarily existed in the form of particulates. Coal combustion and vehicle emissions were the dominant sources of PAH in the observed area of downtown Shanghai. In suburban areas, industrial pollution, from sources such as coke oven, incinerator, and oil fired power plant, was as significant as vehicle emissions in contributing to the deposition of PAHs.

Manganese distribution in brains of Sprague-Dawley rats after 60 days of stainless steel welding-fume exposure.

PubMed

Yu, Il Je; Park, Jung Duck; Park, Eon Sub; Song, Kyung Seuk; Han, Kuy Tae; Han, Jeong Hee; Chung, Yong Hyun; Choi, Byung Sun; Chung, Kyu Hyuck; Cho, Myung Haing

2003-12-01

Welders working in a confined space, as in the shipbuilding industry, are at risk of being exposed to high concentrations of welding fumes and developing pneumoconiosis or other welding-fume exposure related diseases. Among such diseases, manganism resulting from welding-fume exposure remains a controversial issue, as the movement of manganese into specific brain regions has not yet been clearly established. Accordingly, to investigate the distribution of manganese in the brain after welding-fume exposure, male Sprague-Dawley rats were exposed to welding fumes generated from manual metal arc-stainless steel (MMA-SS) at concentrations of 63.6 +/- 4.1 mg/m(3) (low dose, containing 1.6 mg/m(3) Mn) and 107.1 +/- 6.3 mg/m(3) (high dose, containing 3.5 mg/m(3) Mn) total suspended particulate (TSP) for 2 h per day in an inhalation chamber over a 60-day period. Blood, brain, lung, and liver samples were collected after 2 h, 15, 30, and 60 days of exposure and the tissues analyzed for their manganese concentrations using an atomic absorption spectrophotometer. Although dose- and time-dependent increases in the manganese concentrations were found in the lungs and livers of the rats exposed for 60 days, only slight manganese increases were observed in the blood during this period. Major statistically significant increases in the brain manganese concentrations were detected in the cerebellum after 15 days of exposure and up until 60 days. Slight increases in the manganese concentrations were also found in the substantia nigra, basal ganglia (caudate nucleus, putamen, and globus pallidus), temporal cortex, and frontal cortex, thereby indicating that the pharmacokinetics and distribution of the manganese inhaled from the welding fumes were different from those resulting from manganese-only exposure.

Time trend tendency (1988-2014 years) of organochlorine pesticide levels in the adipose tissue of Veracruz inhabitants.

PubMed

Calderón-Garcidueñas, Ana Laura; Waliszewski, Stefan M; Ruiz-Ramos, Rubén; Del Carmen Martinez-Valenzuela, María

2018-03-10

The population that lives in areas where organochlorine pesticides were spread in the past is still exposed to them through contaminated food, particulate matter, and vapors. Due to their lipophilic properties and resistance to metabolic reactions, they accumulate in tissues and fluids rich in lipids. The aim of the study was to monitor the concentrations of organochlorine pesticides in forensic adipose tissue samples of adult inhabitants of Veracruz City, Mexico, and compare their time trend levels from 1988 to 2014. During the study, hexachlorobenzene (HCB); lindane; β-hexachorocyclohexane; p,p'-dichlorodiphenyldichloroethylene (pp'DDE); p,p'-dichlorodiphenyldichloroethane (p,p'-DDT); and o,p'-dichlorodiphenyldichloroethane (o,p'-DDT) were determined. Our survey was divided into two periods: first, from the years 1988 to 1999, during which DDT was allowed to fight malaria and dengue vectors and the second from the years 2001 to 2014, after the DDT ban. A total of 1435 samples were analyzed. There were substantial differences in the forecasted time trend values of p,p'-DDE and p,p'-DDT in human adipose tissue samples in the two different periods. During the first period, p,p'-DDE decrease time trend was 1.198 mg/kg on lipid base per year; for the second one, decrease was 0.128 mg/kg on lipid base per year. p,p'-DDT decreased 0.507 mg/kg on lipid base during the first period and 0.039 mg/kg on lipid base for the second. The different concentrations may be explained by the cessation of fresh exposure after the first period and a more equilibrated decontamination tendency during the second period. This model was useful to show the decrease in the concentration of pesticides in human adipose tissue samples.

PAH emissions from old and new types of domestic hot water boilers.

PubMed

Horak, Jiri; Kubonova, Lenka; Krpec, Kamil; Hopan, Frantisek; Kubesa, Petr; Motyka, Oldrich; Laciok, Vendula; Dej, Milan; Ochodek, Tadeas; Placha, Daniela

2017-06-01

Five different domestic heating boilers (automatic, over-fire, with down-draft combustion and gasification) and three types of fuel (lignite, wood and mixed fuel) were examined in 25 combustion tests and correlated with the emissions of particulate matter (PM), carbon monoxide (CO), total organic carbon (TOC) and 12 polycyclic aromatic hydrocarbons (PAHs with MW = 178-278 g/mol) focusing on particle phase. However, the distribution of 12 PAHs in gas phase was considered as well due to the presence mainly of lighter PAHs in gas phase. The PAHs, as well as the CO and TOC, are the indicators of incomplete combustion, and in this study PAH emission increased significantly with increasing emissions of CO and TOC. The PAHs were mainly detected on PM 2.5 , their contents were increasing linearly with increasing PM 2.5 emissions. The highest emission factors of PAHs were measured for boilers of old construction, such as over-fire boiler (5.8-929 mg/kg) and boiler with down-draft combustion (3.1-54.1 mg/kg). Modern types of boilers produced much lower emissions of PAHs, in particular, automatic boiler (0.3-3.3 mg/kg) and gasification boilers (0.2-6.7 mg/kg). In general, the inefficient combustion at reduced output of boilers generated 1.4-17.7 times more emissions of PAHs than the combustion at nominal output of boilers. It is recommended to operate boilers at nominal output with sufficient air supply and to use the proper fuel to minimise PAHs emissions from domestic heating appliances. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mesopelagic microplankton of the Arabian Sea

NASA Astrophysics Data System (ADS)

Gowing, Marcia M.; Garrison, David L.; Wishner, Karen F.; Gelfman, Celia

2003-10-01

The Arabian Sea is notable for its dramatic monsoonal effects on euphotic zone biogeochemical processes and the large spatial extent of its mesopelagic oxygen minimum zone. As part of the US Joint Global Ocean Flux Study Arabian Sea project, we sampled microplankton (organisms 20-200 μm including diatoms, dinoflagellates, ciliates, sarcodines and nauplii) at five depths from 250 to 1000 or 1100 m at six stations during four seasonal cruises in 1995. Abundances of groups of organisms at discrete depths averaged 1-2 l -1 seasonally. Mean seasonal integrated biomass of the assemblage was 29 mg C m -2 during the late Northeast Monsoon, 37 mg C m -2 during the Spring Intermonsoon, 47 mg C m -2 during the late Southwest Monsoon and 49 mg C m -2 during the early Northeast Monsoon. Overall, protozoans dominated the mesopelagic microplankton assemblage. Integrated biomass peaked during the late SW Monsoon at two stations as expected if microplankton responded to surface productivity and mesopelagic organic carbon fluxes. At three stations, microplankton biomass peaked during the early NE Monsoon; this may reflect a continuing response to SW Monsoon productivity signals by these larger, slow-growing organisms. Protozooplankton abundance did not appear to be negatively affected by low (<0.1 ml dissolved O 2 l -1) oxygen, whereas naupliar abundance and biomass were higher where oxygen concentration was higher. Total microplankton biomass was highest where oxygen concentrations and also mesozooplankton biomass were lowest, suggesting that predation also played a role in microplankton distributions. Calculations based on allometric relationships indicated that the mesopelagic heterotrophic microplankton assemblage could, on average, respire 9-38% of the particulate carbon flux that entered the system at 100 m and possibly 18-76% of the flux remaining at 250 m. Microplankton may therefore be significant carbon cyclers in the ocean's vast "twilight zone".

Reticuloendothelial clearance of blood-borne particulates: relevance to experimental lung microembolization and vascular injury.

PubMed

Niehaus, G D; Schumacker, P R; Saba, T M

1980-04-01

The rapid increase in sheep lung vascular permeability observed during Pseudomonas aeruginosa bacteremia may be due to embolization of the pulmonary microvasculature by bloodborne particulates. Since alterations in lung microvascular permeability during mild septicemia in sheep may reflect inefficient RES phagocytic clearance of bacteria as well as products of bacterial induced intravascular coagulation, the opsonic and phagocytic aspects of RES function in sheep (30-50 kg) were compared to other species. RES function was evaluated by both the clearance and relative organ uptake of gelatinized I(131) RE test lipid emulsion and gelatinized colloidal carbon. Immunoreactive opsonic a(2)SB glycoprotein levels were determined by electroimmunoassay. The phagocytic index for RES clearance of the gelatinized (500 mg/kg) test lipid in sheep was 0.019 +/- 0.002 corresponding to a half-time of 16.65 +/- 1.74 minutes. With colloidal carbon (64 mg/kg), the phagocytic index in sheep was 0.080 +/- 0.026, corresponding to a half-time of 6.16 +/- 1.99 minutes. The per cent of injected lipid emulsion (%ID) in major RE organs, on a total organ basis (TO), was: liver = 15.69 +/- 1.65%; spleen = 2.09 +/- 0.78%. Localization in the lung = 31.39 +/- 6.2%. The per cent of carbon localized in major RE organs (%ID/TO) was: liver = 21.37 +/- 1.9%; spleen = 1.95 +/- 0.55%. Localization in the lung = 32.70 +/- 4.55%. In contrast, clearance and organ distribution of the blood-borne test microparticles in rats and dogs at the same relative challenging dose revealed a much more intense and rapid liver and spleen RES uptake with minimal lung localization (1-2%). Immunoreactive opsonic protein concentrations varied greatly with species and directly correlated with efficiency of RES function. Levels observed were: dog = 1285 +/- 135 microg/ml; mouse = 1077 +/- 67 microg/ml; rat = 400 +/- 31 microg/ml; human = 297 +/- 10 microg/ml; and sheep = 184 +/- 13 microg/ml. After intravenous particulate challenge, circulating immunoreactive opsonic protein in the sheep was depleted (p < 0.05) rapidly with partial recovery at 24 hours and mild rebound hyperopsonemia at 48 hours. This pattern is in contrast to the rapid restoration seen in dog and rat within three to six hours postchallenge. Thus, in sheep, the extensive pulmonary localization of blood-borne microparticles appears related to inefficient RES clearance function mediated by a relative deficiency of circulating opsonic protein (plasma fibronectin).

Generation of hydroxyl radicals by urban suspended particulate air matter. The role of iron ions

NASA Astrophysics Data System (ADS)

Valavanidis, Athanasios; Salika, Anastasia; Theodoropoulou, Anna

Recent epidemiologic studies showed statistical associations between particulate air pollution in urban areas and increased morbidity and mortality, even at levels well within current national air quality standards. Inhalable particulate matter (PM 10) can penetrate into the lower airways where they can cause acute and chronic lung injury by generating toxic oxygen free radicals. We tested inhalable total suspended particulates (TSP) from the Athens area, diesel and gasoline exhaust particles (DEP and GED), and urban street dusts, by Electron Paramagnetic Resonance (EPR). All particulates can generate hydroxyl radicals (HO ṡ), in aqueous buffered solutions, in the presence of hydrogen peroxide. Results showed that oxidant generating activity is related with soluble iron ions. Leaching studies showed that urban particulate matter can release large amounts of Fe 3+ and lesser amounts of Fe 2+, as it was shown from other studies. Direct evidence of HO ṡ was confirmed by spin trapping with DMPO and measurement of DMPO-OH adduct by EPR. Evidence was supported with the use of chelator (EDTA), which increases the EPR signal, and the inhibition of the radical generating activity by desferrioxamine or/and antioxidants ( D-mannitol, sodium benzoate).

Can neap-spring tidal cycles modulate biogeochemical fluxes in the abyssal near-seafloor water column?

NASA Astrophysics Data System (ADS)

Turnewitsch, Robert; Dale, Andrew; Lahajnar, Niko; Lampitt, Richard S.; Sakamoto, Kei

2017-05-01

Before particulate matter that settles as 'primary flux' from the interior ocean is deposited into deep-sea sediments it has to traverse the benthic boundary layer (BBL) that is likely to cover almost all parts of the seafloor in the deep seas. Fluid dynamics in the BBL differ vastly from fluid dynamics in the overlying water column and, consequently, have the potential to lead to quantitative and compositional changes between primary and depositional fluxes. Despite this potential and the likely global relevance very little is known about mechanistic and quantitative aspects of the controlling processes. Here, results are presented for a sediment-trap time-series study that was conducted on the Porcupine Abyssal Plain in the abyssal Northeast Atlantic, with traps deployed at 2, 40 and 569 m above bottom (mab). The two bottommost traps were situated within the BBL-affected part of the water column. The time series captured 3 neap and 4 spring tides and the arrival of fresh settling material originating from a surface-ocean bloom. In the trap-collected material, total particulate matter (TPM), particulate inorganic carbon (PIC), biogenic silica (BSi), particulate organic carbon (POC), particulate nitrogen (PN), total hydrolysable amino acids (AA), hexosamines (HA) and lithogenic material (LM) were determined. The biogeochemical results are presented within the context of time series of measured currents (at 15 mab) and turbidity (at 1 mab). The main outcome is evidence for an effect of neap/spring tidal oscillations on particulate-matter dynamics in BBL-affected waters in the deep sea. Based on the frequency-decomposed current measurements and numerical modelling of BBL fluid dynamics, it is concluded that the neap/spring tidal oscillations of particulate-matter dynamics are less likely due to temporally varying total free-stream current speeds and more likely due to temporally and vertically varying turbulence intensities that result from the temporally varying interplay of different rotational flow components (residual, tidal, near-inertial) within the BBL. Using information from previously published empirical and theoretical relations between fluid and biogeochemical dynamics at the scale of individual particle aggregates, a conceptual and semi-quantitative picture of a mechanism was derived that explains how the neap/spring fluid-dynamic oscillations may translate through particle dynamics into neap/spring oscillations of biogeochemical aggregate decomposition (microbially driven organic-matter breakdown, biomineral dissolution). It is predicted that, during transitions from neap into spring tides, increased aggregation in near-seafloor waters and/or reduced deposition of aggregates at the seafloor coincides with reduced biogeochemical particulate-matter decomposition in near-seafloor waters. By contrast, during transitions from spring into neap tides, enhanced biogeochemical particulate-matter decomposition in near-seafloor waters is predicted to coincide with increased deposition of particulate matter at the seafloor. This study suggests that, in addition to current speed, the specifics and subtleties of the interplay of different rotational flow components can be an important control on how the primary flux from the interior ocean is translated into the depositional flux, with potential implications for sedimentary carbon deposition, benthic food supply and possibly even the sedimentary records of environmental change.

Analysis of particulate contamination on tape lift samples from the VETA optical surfaces

NASA Technical Reports Server (NTRS)

Germani, Mark S.

1992-01-01

Particulate contamination analysis was carried out on samples taken from the Verification Engineering Test Article (VETA) x-ray detection system. A total of eighteen tape lift samples were taken from the VETA optical surfaces. Initially, the samples were tested using a scanning electron microscope. Additionally, particle composition was determined by energy dispersive x-ray spectrometry. Results are presented in terms of particle loading per sample.

Fuel-Burning Technology Alternatives for the Army.

DTIC Science & Technology

1985-01-01

control 0.85 2,287,000 Flue gas desulfurization 0.68 3,410,000 Total 12,478,000 *Capital cost estimate...34......... . . Particulate and sulfur dioxide control are needed. A baghouse and flue gas desulfurization (FD) scrubber system must be installed. Each item’s cost in...direct cost) Contingency (20% of 1,253,000 direct and indirect costs) Subtotal 7,518,000 Particulate control 1,342,000 Flue gas desulfurization

Precipitation scavenging of polychlorinated biphenyl congeners in the great lakes region

NASA Astrophysics Data System (ADS)

Murray, Michael W.; Andren, Anders W.

Ten precipitation events were sampled in the fall of 1986 in Madison, WI and analyzed for individual congener and total polychlorinated biphenyl (PCB) levels in both the dissolved and particulate phases. Total PCB concentrations were generally at the lower end of ranges recently reported for precipitation. Operationally defined dissolved and particulate phase congener distribution patterns for the two events of highest concentration were qualitatively similar to gas-phase and particle-bound patterns for northern Wisconsin air samples. Higher than predicted dissolved-phase concentrations may indicate non-equilibrium processes during scavenging and/or sample processing, the presence of colloids and micro-particulates, and/or more efficient gas-phase transfer to hydrometeors with organic coatings. Observed organic carbon-normalized distribution coefficients increased slightly with increasing octanol-water partition coefficient, giving the relationship log Koc = 0.22 log Kow + 4.64. The data indicate that a third organic-rich colloidal phase could be influencing partitioning, and could explain the higher than expected apparent gas scavenging efficiency for PCBs from the atmosphere. Precipitation-weighted mean fluxes of PCBs in the dissolved and particulate phases were 1.2 and 1.4 μg m -2 year -1, respectively, indicating that precipitation remains a significant source of PCBs to the upper Great Lakes.

Particulate Study on NeoProfen, a Neonatal Injectable Product.

PubMed

Krishna, Aravind; Rice, Michael; Kester, Tom; Waters, Michael; Wilson, Terry

2016-01-01

NeoProfen or sterile ibuprofen L-lysine at 10 mg/mL ibuprofen, in 2 mL single-use Type I glass vials is often a first choice medication used to close a patent ductus arteriosus in neonatal patients from 500 to 1500 g body weight. Visible particulate matter was found in vials that were placed on a commercial stability program prior to the approved expiration date of 2 years. A combination of instrumental techniques including inductively coupled plasma-mass spectrometry, x-ray photoelectron spectroscopy, scanning electron microscopy energy dispersive x-ray spectrometry, and Raman and Fourier transform infrared microspectroscopy was used to evaluate stability, pilot batch and packaging samples in a root cause investigation. The particulate matter was shown to consist largely of ibuprofen aluminum salts of various stoichiometries. It developed over time by a substitution mechanism, in which the ibuprofen anion in solution reacts with the aluminum oxide network of the borosilicate glass giving the ibuprofen aluminum salt with =Al-OH remaining in the network. For corrective action an alternate Type I borosilicate glass vial with interior coating, not found in the original vial, was chosen for the product to prevent this occurrence. NeoProfen (sterile preservative-free ibuprofin L-lysine at 17 mg/mL in a single-use glass vial) is used to close a clinically significant patent ductus arteriosus in premature infants no more than 32 weeks gestational age. The neonatal population is especially sensitive to outside chemical, physical and environmental conditions because of incompletely developed organ systems, low birth weight and other underlying conditions. Two batches of this product were voluntarily recalled by the manufacturer, Lundbeck, and investigated for the source of particulate matter observed during a commercial stability testing program. This was found to result from an interaction between the product and the Type I borosilicate glass vial where ibuprofen substitutes for the aluminum oxide network in the glass, forming an ibuprofen aluminum hydroxide salt as particulate. In order to prevent this salt formation an alternate glass vial was chosen which had interiors treated using a chemical vapor deposition technique. These vials were found to preserve NeoProfen quality properties during short term stress and medium term stability studies. © PDA, Inc. 2016.

Surface-Water Quantity and Quality of the Upper Milwaukee River, Cedar Creek, and Root River Basins, Wisconsin, 2004

USGS Publications Warehouse

Hall, David W.

2006-01-01

The U.S. Geological Survey, in cooperation with the Southeastern Wisconsin Regional Planning Commission (SEWRPC), collected discharge and water-quality data at nine sites in previously monitored areas of the upper Milwaukee River, Cedar Creek, and Root River Basins, in Wisconsin from May 1 through November 15, 2004. The data were collected for calibration of hydrological models that will be used to simulate how various management strategies will affect the water quality of streams. The data also will support SEWRPC and Milwaukee Metropolitan Sewerage District (MMSD) managers in development of the SEWRPC Regional Water Quality Management Plan and the MMSD 2020 Facilities Plan. These management plans will provide a scientific basis for future management decisions regarding development and maintenance of public and private waste-disposal systems. In May 2004, parts of the study area received over 13 inches of precipitation (3.06 inches is normal). In June 2004, most of the study area received between 7 and 11 inches of rainfall (3.56 inches is normal). This excessive rainfall caused flooding throughout the study area and resultant high discharges were measured at all nine monitoring sites. For example, the mean daily discharge recorded at the Cedar Creek site on May 27, 2004, was 2,120 cubic feet per second. This discharge ranked ninth of the largest 10 mean daily discharges in the 75-year record, and was the highest discharge recorded since March 30, 1960. Discharge records from continuous monitoring on the Root River Canal near Franklin since October 1, 1963, indicated that the discharge recorded on May 23, 2004, ranked second highest on record, and was the highest discharge recorded since March 4, 1974. Water-quality samples were taken during two base-flow events and six storm events at each of the nine sites. Analysis of water-quality data indicated that most concentrations of dissolved oxygen, biological oxygen demand, fecal coliform bacteria, chloride, suspended solids, nitrate plus nitrite nitrogen, ammonia nitrogen, Kjeldahl nitrogen, total phosphorus, dissolved orthophosphorus, total copper, particulate mercury, dissolved mercury, particulate methylmercury, dissolved methylmercury, and total zinc were below U.S. Environmental Protection Agency (USEPA) and State of Wisconsin water-quality standards at all sites, with the exception of dissolved oxygen at the Kewaskum, Farmington, Root River Canal, Root River Racine, and Root River Mouth sites. Each of these sites had from several days to several weeks of daily average dissolved oxygen concentrations below the 5 milligrams per liter State of Wisconsin standard for aquatic life. The lowest dissolved oxygen concentrations were measured at the heavily urbanized Root River Mouth site in downtown Racine, Wisconsin, where elevated concentrations of ammonia may have contributed to oxygen consumption during oxidation of ammonia to nitrate. Additionally, the maximum concentrations of copper in several Root River samples exceeded draft USEPA Ambient Water-Quality Criteria (U.S. Environmental Protection Agency, 2003) for acute toxicity to several species of aquatic organisms. Substantial water-quality changes were not correlated with hydrologic changes at any of the nine sites. Base-flow water-quality was generally indistinguishable from that sampled during storm events. The sparsely developed upper Milwaukee River and Cedar Creek Basins had relatively low ranges of contamination for all laboratory-reported parameters. For all nine sites, the highest reported concentrations of chloride (216 mg/L), total phosphorus (0.627 mg/L), ortho-phosphorus (0.136 mg/L), nitrate plus nitrate (9.32 mg/L), and copper (38 ?g/L) were reported for samples collected at the Root River Canal site. The highest concentrations of fecal coliforms (3,600 colonies per 100 mL) and Escherichia coli (2,300 colonies per 100 mL) were reported in samples collected at Kewaskum. The highest concentrations of s

Evaluation of the capability of low-impact development practices for the removal of heavy metal from urban stormwater runoff.

PubMed

Maniquiz-Redillas, Marla C; Kim, Lee-Hyung

2016-09-01

Low-impact development (LID) and green infrastructure (GI) have recently become well-known methods to capture, collect, retain, and remove pollutants in stormwater runoff. The research was conducted to assess the efficiency of LID/GI systems applied in removing the particulate and dissolved heavy metals (Zn, Pb, Cu, Ni, Cr, Cd, and Fe) from urban stormwater runoff. A total of 82 storm events were monitored over a four-year period (2010-2014) on six LID/GI systems including infiltration trenches, tree box filter, rain garden, and hybrid constructed wetlands employed for the management of road, parking lot, and roof runoff. It was observed that the heavy metal concentration increased proportionally with the total suspended solids concentration. Among the heavy metal constituents, Fe appeared to be highly particulate-bound and was the easiest to remove followed by Zn and Pb; while metals such as Cr, Ni, Cu, and Cd were mostly dissolved and more difficult to remove. The mass fraction ratios of metal constituents at the effluent were increased relative to the influent. All the systems performed well in the removal of particulate-bound metals and were more efficient for larger storms greater than 15 mm wherein more particulate-bound metals were generated compared to smaller storms less than 5 mm that produced more dissolved metals. The efficiency of the systems in removing the particulate-bound metals was restricted during high average/peak flows; that is, high-intensity storms events and when heavy metals have low concentration levels.

The Concentrations but Not the Components of Particulate Material and Secondary Transformation Products May Account for Much of the Variation in Air Mutagenicity

EPA Science Inventory

The mutagenic potency of ambient air PM in the Salmonella mutagenicity assay (rev/mg PM) varies only ~1 order of magnitude worldwide; however, the mutagenic potency of the air itself (rev/m3 of air) varies ~5 orders of magnitude (IARC Monograph Vol 109, 2016). Thus, the componen...

40 CFR 92.114 - Exhaust gas and particulate sampling and analytical system.

Code of Federal Regulations, 2011 CFR

2011-07-01

... downstream of the analyzer. The gauge tap must be within 2 inches of the analyzer exit port. Gauge... must be used. The gauge tap must be within 2 inches of the analyzer entrance port. (vi) Calibration or.... Equivalent loadings (0.5 mg/1075 mm2 stain area) shall be used as target loadings when other filter sizes are...

40 CFR 92.114 - Exhaust gas and particulate sampling and analytical system.

Code of Federal Regulations, 2010 CFR

2010-07-01

... downstream of the analyzer. The gauge tap must be within 2 inches of the analyzer exit port. Gauge... must be used. The gauge tap must be within 2 inches of the analyzer entrance port. (vi) Calibration or.... Equivalent loadings (0.5 mg/1075 mm2 stain area) shall be used as target loadings when other filter sizes are...

Mutagenicity of airborne particulates in the rubber industry.

PubMed

Barański, B; Indulski, J; Janik-Spiechowicz, E; Palus, J

1989-12-01

The aim of this work was to evaluate the mutagenic activity of airborne particulate matter in the rubber industry. Air was sucked through Whatman glass-fibre filters with Staplex pumps and adsorbed substances and fume particles were extracted with acetone or toluene for 2 h in a ultrasonic cleaner. After separation of the insoluble solid phase by filtration, solvent was evaporated at a temperature of 70 degrees C in an argon atmosphere. The residue was stored at -20 degrees C. Mutagenicity was determined by the Salmonella plate incorporation assay with the tester strain TA98 and activity is related either to the weight of aerosol (rev mg-1) or to the volume of atmospheric sample (rev m-3). The fumes emitted from the tyre tread line, calender feeding, and tyre vulcanizing processes, showed the highest mutagenic activity (55-211 rev mg-1, + S9). At these and at other workplaces (extruder mill, carbon black station, mixer loading), mutagenic activity related to the volume of air was in the range of 22-158 rev m-3, + S9. The results indicate the need to reduce and monitor mutagenic contamination in order to increase the safety of work in the rubber industry.

Source identification of particulate matter in a semi-urban area of Malaysia using multivariate techniques.

PubMed

Wahid, N B A; Latif, M T; Suan, L S; Dominick, D; Sahani, M; Jaafar, S A; Mohd Tahir, N

2014-03-01

This study aims to determine the composition and sources of particulate matter with an aerodynamic diameter of 10 μm or less (PM10) in a semi-urban area. PM10 samples were collected using a high volume sampler. Heavy metals (Fe, Zn, Pb, Mn, Cu, Cd and Ni) and cations (Na(+), K(+), Ca(2+) and Mg(2+)) were detected using inductively coupled plasma mass spectrometry, while anions (SO4 (2-), NO3 (-), Cl(-) and F(-)) were analysed using Ion Chromatography. Principle component analysis and multiple linear regressions were used to identify the source apportionment of PM10. Results showed the average concentration of PM10 was 29.5 ± 5.1 μg/m(3). The heavy metals found were dominated by Fe, followed by Zn, Pb, Cu, Mn, Cd and Ni. Na(+) was the dominant cation, followed by Ca(2+), K(+) and Mg(2+), whereas SO4 (2-) was the dominant anion, followed by NO3 (-), Cl(-) and F(-). The main sources of PM10 were the Earth's crust/road dust, followed by vehicle emissions, industrial emissions/road activity, and construction/biomass burning.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gough, M.A.; Fauzi, R.; Mantoura, C.

The vascular land plant biopolymers lignin and cutin were surveyed in the surface sediments of coastal and open ocean waters by controlled alkaline CuO oxidation/reaction. Two contrasting oceanic regimes were studied: the northwest Mediterranean (NWM) Sea, which receives significant particulate terrigenous debris through riverine discharge; and the northeast Atlantic (NEA) Ocean, with poorly characterized terrestrial carbon inputs. In the NWM products of lignin and cutin co-occurred at all stations, elevated levels (ca. 0.5-3.0 mg lignin phenols/100 mg organic carbon; ca. 0.01-0.09 mg cutin acids/100 mg organic carbon) were observed for near-shore deltaic and shelf sediments. The influence of terrestrial landmore » plant inputs extended across the shelf and through the slope to the abyssal plain, providing molecular evidence for advective offshore transfer of terrestrial carbon. Mass balance estimates for the basin suggest riverine inputs account for the majority of surface sedimentary ligin/cutin, most of which (>90%) is deposited on the shelf. Products of CuO oxidation of lignin and cutin were also detected in NEA surface sediments, at levels comparable to those observed for the NWM continental slope, and were detectable at low concentrations in the sediments of the abyssal plains (>4,000 m depth). While atmospheric deposition of lignin/cutin-derived material cannot be discounted in this open ocean system, lateral advective transfer of enriched shelf sediments is inferred as a possible transport process. A progressive enrichment in cutin-derived material relative to lignin was observed offshore, with evidence of an increase in the degree of oxidative alteration of lignin residues. Preliminary mass balance calculations applied to the global ocean margin suggest riverine sources of both particulate lignin and cutin are important and that most (>95%) deposition of recognizable land plant biopolymers occurs in shelf seas. 74 refs., 7 figs., 5 tabs.« less

Particulate emissions from a beef cattle feedlot using the flux-gradient technique.

PubMed

Bonifacio, Henry F; Maghirang, Ronaldo G; Trabue, Steven L; McConnell, Laura L; Prueger, John H; Razote, Edna B

2013-09-01

Data on air emissions from open-lot beef cattle () feedlots are limited. This research was conducted to determine fluxes of particulate matter with an aerodynamic diameter ≤10 μm (PM) from a commercial beef cattle feedlot in Kansas using the flux-gradient technique, a widely used micrometeorological method for air emissions from open sources. Vertical PM concentration profiles and micrometeorological parameters were measured at the feedlot using tapered element oscillating microbalance PM samplers and eddy covariance instrumentations (i.e., sonic anemometer and infrared hygrometer), respectively, from May 2010 through September 2011, representing feedlot conditions with air temperatures ranging from -24 to 39°C. Calculated hourly PM fluxes varied diurnally and seasonally, ranging up to 272 mg m h, with an overall median of 36 mg m h. For warm conditions (air temperature of 21 ± 10°C), the highest hourly PM fluxes (range 116-146 mg m h) were observed during the early evening period, from 2000 to 2100 h. For cold conditions (air temperature of -2 ± 8°C), the highest PM fluxes (range 14-27 mg m h) were observed in the afternoon, from 1100 to 1500 h. Changes in the hourly trend of PM fluxes coincided with changes in friction velocity, air temperature, sensible heat flux, and surface roughness. The PM emission was also affected by the pen surface water content, where a water content of at least 20% (wet basis) would be sufficient to effectively reduce PM emissions from pens by as much as 60%. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Under contract with the US Department of Energy (DE-AC22-92PCO0367), Pittsburgh Energy Technology Center, Radian Corporation has conducted a test program to collect and analyze size-fractionated stack gas particulate samples for selected inorganic hazardous air pollutants (HAPS). Specific goals of the program are (1) the collection of one-gram quantities of size-fractionated stack gas particulate matter for bulk (total) and surface chemical charactization, and (2) the determination of the relationship between particle size, bulk and surface (leachable) composition, and unit load. The information obtained from this program identifies the effects of unit load, particle size, and wet FGD system operation on themore » relative toxicological effects of exposure to particulate emissions.« less

40 CFR 86.085-2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... represents the manufacturer's total diesel light-duty vehicle production for those engine families being... standard. PRODLDT represents the manufacturer's total diesel light-duty truck production for those engine... average particulate emission level, for certification purposes, of all of its diesel engine families...

Parameterizing the equilibrium distribution of chemicals between the dissolved, solid particulate matter, and colloidal matter compartments in aqueous systems

USGS Publications Warehouse

Pankow, J.F.; McKenzie, S.W.

1991-01-01

The manner in which a chemical material partitions among the dissolved (D), participate (P), and colloidal (C) phases affects both its chemical and physical behavior in the aquatic environment. The fractions of the chemical that are present in each of these three phases will be determined by the values of two simple parameters, KpSp/??w and KcSc/??w. The variables Kp and Kc are the particle/water and colloid/water partition constants (mL/g), respectively, Sp and Sc are the volume concentrations of particulate and colloidal material (mg/L), respectively, and ??w is the fractional volume of the system that is aqueous. This parameterization allows a rapid overview of how partitioning (1) changes as a function of chemical partitioning properties and water type, (2) affects apparent partition constants (i.e., Kpapp values) computed between the particulate phase and the remainder of the system, and (3) causes Kpapp values to become independent of chemical properties at high values of KcSc/??w. ?? 1991 American Chemical Society.

Enhanced hydrophilicity of chlorided aluminum oxide particulates

NASA Technical Reports Server (NTRS)

Cofer, W. R., III

1978-01-01

An enhancement of hydrophilicity for chlorided aluminas was demonstrated by the results obtained from gaseous H2O sorptions at 70-, 80-, and 86-percent relative humidity on alpha and gamma aluminum oxide particulates and on alpha and gamma aluminum oxide particulates with a chemisorbed surface chloride phase (produced by reactions of gaseous HCl + H2O on alumina). Continuous sorption histories for H2O on chlorided aluminas having specific surface areas that range from 7 to 227 sq m/g before chloriding indicated that initial sorption rates were directly linked to the extent of chemisorbed chlorided coverage and implied the same relationship for sorption capacities. The initial sorption rate on chlorided aluminas was found to be slower for the first exposure to H2O than for subsequent exposures (which reached equilibrated H2O coverages much faster), suggesting that slow chemical reactions between H2O and chlorided alumina may have been operative during initial exposures. Chlorided alumina particles were found to remain very hydrophilic (relative to nonchlorided analogs) for several H2O sorption/desorption cycles.

A retrospective review of the carcinogenicity of refractory ceramic fiber in two chronic fischer 344 rat inhalation studies: an assessment of the MTD and implications for risk assessment.

PubMed

Mast, R W; Yu, C P; Oberdörster, G; McConnell, E E; Utell, M J

2000-12-01

The purpose of this article is to review previous chronic inhalation studies in rats with refractory ceramic fiber (RCF), the mathematical modeling efforts to describe the deposition, clearance, and retention of RCF fiber in the rat and human, and the concept of "overload," and to assess the possibility that the maximum tolerated dose (MTD) was exceeded. Lastly, based on recent biopersistence and pulmonary clearance studies of several investigators with a particulate-free RCF, we examine the potential impact on the chronic RCF rat bioassay of coexposure to both RCF particulate and RCF fibers. The review concludes, inter alia, that RCF particulate coexposure probably had a major impact on the observed chronic adverse effects, that the MTD was probably exceeded at the highest exposure concentration of 30 mg/m(3) in the rat bioassay, and that inclusion of the highest dose in the risk assessment process may overstate human health risk if a linear rather than nonlinear model is used.

The contamination of rain samples by dry deposition on rain collectors

NASA Astrophysics Data System (ADS)

Fowler, D.; Cape, J. N.

A series of short-term experiments at a rural site in eastern Scotland showed that dry deposition of SO 2 gas onto pyrex glass rain collectors in dry weather approached saturation after 24 h and contributed c. 80 % of dry-deposited S, the remaining 20 % being attributable to Particulate sulphate. A comparison over 3 years of soluble sulphate from funnel washings after dry days with daily concentrations of SO 2 and particulate sulphate was well fitted by a linear dependence on Particulate sulphate and a logarithmic dependence on SO 2 concentrations. Particulate sulphate contributed 34 (+- 7) % of the dry deposition on dry days, although there was a marked seasonal variation in the total dry deposit of S on the collector which was independent of SO 2 and particulate sulphate concentrations. A comparison of monthly and daily collectors at the same site from April to September was consistent with these estimates of dry deposition on dry days. An extrapolation to sites with similar collectors in northern Britain showed that between 1S and 35 % of the monthly collected non-marine sulphate could have been dry-deposited on the collector.

Spatial Statistics of atmospheric particulate matter in China

NASA Astrophysics Data System (ADS)

Huang, Yongxiang; Wang, Yangjun; Liu, Yulu

2017-04-01

In this work, the spatial dynamics of the atmospheric particulate matters (resp. PM10 and PM2.5) are studied using turbulence methodologies. The hourly concentrations of particulate matter were released by the Chinese government (http://www.cnemc.cn). We first processed these data into daily average concentrations. Totally, there are 305 monitor stations with an observations period of 425 days. It is found experimentally that the spatial correlation function ρ(r) shows a log-law on the mesoscale range, i.e., 50 ≤ r ≤ 500 km, with an experimental scaling exponent β = 0.45. The spatial structure function shows a power-law behavior on the mesoscale range 90 ≤ r ≤ 500 km. The experimental scaling exponent ζ(q) is convex, showing that the intermittent correction is relevant in characterizing the spatial dynamics of particulate matter. The measured singularity spectrum f(α) also shows its multifractal nature. Experimentally, the particulate matter is more intermittent than the passive scalar, which could be partially due to the mesoscale movements of the atmosphere, and also due to local sources, such as local industry activities.

The effects of evaporating essential oils on indoor air quality

NASA Astrophysics Data System (ADS)

Su, Huey-Jen; Chao, Chung-Jen; Chang, Ho-Yuan; Wu, Pei-Chih

Essential oils, predominantly comprised of a group of aromatic chemicals, have attracted increasing attention as they are introduced into indoor environments through various forms of consumer products via different venues. Our study aimed to characterize the profiles and concentrations of emitted volatile organic compounds (VOCs) when evaporating essential oils indoors. Three popular essential oils in the market, lavender, eucalyptus, and tea tree, based on a nation-wide questionnaire survey, were tested. Specific aromatic compounds of interest were sampled during evaporating the essential oils, and analyzed by GC-MS. Indoor carbon monoxide (CO), carbon dioxide (CO 2), total volatile organic compounds (TVOCs), and particulate matters (PM 10) were measured by real-time, continuous monitors, and duplicate samples for airborne fungi and bacteria were collected in different periods of the evaporation. Indoor CO (average concentration 1.48 vs. 0.47 ppm at test vs. background), CO 2 (543.21 vs. 435.47 ppm), and TVOCs (0.74 vs. 0.48 ppm) levels have increased significantly after evaporating essential oils, but not the PM 10 (2.45 vs. 2.42 ppm). The anti-microbial activity on airborne microbes, an effect claimed by the use of many essential oils, could only be found at the first 30-60 min after the evaporation began as the highest levels of volatile components in these essential oils appeared to emit into the air, especially in the case of tea tree oil. High emissions of linalool (0.092-0.787 mg m -3), eucalyptol (0.007-0.856 mg m -3), D-limonene (0.004-0.153 mg m -3), ρ-cymene (0.019-0.141 mg m -3), and terpinene-4-ol-1 (0.029-0.978 mg m -3), all from the family of terpenes, were observed, and warranted for further examination for their health implications, especially for their potential contribution to the increasing indoor levels of secondary pollutants such as formaldehyde and secondary organic aerosols (SOAs) in the presence of ozone.

40 CFR 86.085-2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... represents the manufacturer's total diesel light-duty vehicle production for those engine families being... standard. PRODLDT represents the manufacturer's total diesel light-duty truck production for those engine... particulate emission level, for certification purposes, of all of its diesel engine families included in the...

Respiratory symptoms and lung functional impairments associated with occupational exposure to asphalt fumes.

PubMed

Neghab, M; Zare Derisi, F; Hassanzadeh, J

2015-04-01

Controversy exists as to the potential of asphalt fumes to induce respiratory symptoms and lung functional impairments. To examine the respiratory effects, if any, of occupational inhalation exposure to asphalt fumes. In this cross-sectional study, 74 asphalt workers and 110 unexposed employees were investigated. The prevalence of respiratory symptoms among subjects was investigated by a standard questionnaire. Additionally, the parameters of pulmonary function were measured both, prior to exposure and at the end of work-shift. Furthermore, to assess the extent to which workers were exposed to asphalt fumes, total particulate and the benzene-soluble fraction were measured in different worksites. The mean levels of exposure to total particulate and benzene-soluble fraction in asphalt fumes were estimated to be 0.9 (SD 0.2) and 0.3 (SD 0.1) mg/m^3, respectively. Mean values of FEV1, both prior to the exposure (89.58% [SD 18.69%] predicted value) and at the end of shift (85.38% [SD 19.4%]), were significantly (p<0.05) smaller than those of the comparison subjects (93.88% [SD 13.93%]). Similarly, pre-shift (87.05 [SD 8.57]) and postexposure (89.95 [SD 6.85]) FEV1/FVC ratio were both significantly (p<0.01) lower than those of the unexposed employees (107.56 [SD 9.64]). Moreover, the prevalence of respiratory symptoms such as cough and wheezing in exposed employees were 41% and 42%, respectively. The corresponding values for comparison subjects were 10.0% and 3.6%, respectively (p<0.001). The pattern of changes in parameters of lung function in asphalt workers was consistent with that of chronic obstructive lung disease. Significant decrements in the parameters of pulmonary function as well as, a significant increase in the prevalence of respiratory symptoms in asphalt paving workers compared to their unexposed counterparts provided evidence in favor of a significant association between exposure to asphalt fumes and lung function impairments.

Exposure to polycyclic aromatic hydrocarbons (PAHs), mutagenic aldehydes and particulate matter during pan frying of beefsteak.

PubMed

Sjaastad, Ann Kristin; Jørgensen, Rikke Bramming; Svendsen, Kristin

2010-04-01

Cooking with gas or electric stoves produces fumes, especially during frying, that contain a range of harmful and potentially mutagenic compounds as well as high levels of fine and ultrafine particles. The aim of this study was to see if polycyclic aromatic hydrocarbons (PAHs) and higher mutagenic aldehydes which were collected in the breathing zone of the cook, could be detected in fumes from the frying of beefsteak. The frying was performed in a model kitchen in conditions similar to those in a Western European restaurant kitchen. The levels of PAHs (16 EPA standard) and higher aldehydes (trans,trans-2,4-decadienal, 2,4-decadienal, trans-trans-2,4-nonadienal, trans-2-decenal, cis-2-decenal, trans-2-undecenal, 2-undecenal) were measured during frying on an electric or gas stove with margarine or soya bean oil as the frying fat. The number concentration of particles <100 nm in size (ultrafine) was also measured, as well as the mass concentration of total particulate matter. Levels of naphthalene were in the range of 0.15-0.27 microg/m(3) air. Measured levels of mutagenic aldehydes were between non-detectable and 61.80 microg/m(3) air. The exposure level of total aerosol was between 1.6 and 7.2 mg/m(3) air. Peak number concentrations of ultrafine particles were in the range of 6.0x10(4)-89.6x10(4) particles/cm(3) air. Naphthalene and mutagenic aldehydes were detected in most of the samples. The levels were variable, and seemed to be dependent on many factors involved in the frying process. However, according to the present results, frying on a gas stove instead of an electric stove causes increased occupational exposure to some of the components in cooking fumes which may cause adverse health effects.

Transport and retention of phosphorus in surface water in an urban slum area

NASA Astrophysics Data System (ADS)

Nyenje, P. M.; Meijer, L. M. G.; Foppen, J. W.; Kulabako, R.; Uhlenbrook, S.

2013-08-01

The transport of excessive phosphorus (P) discharged from unsewered informal settlements (slums) due to poor on-site sanitation is largely unknown. Hence, we investigated the processes governing P transport in a 28 km2 slum-dominated catchment in Kampala, Uganda. During high runoff events and a period of base flow, we collected hourly water samples (over 24 h) from a primary channel draining the catchment and from a small size tertiary channel draining one of the contributing slum areas (0.5 km2). Samples were analyzed for orthophosphate (PO4-P), particulate P (PP), total P (TP) and selected hydro-chemical parameters. Channel bed and suspended sediments were collected to determine their sorption potential, geo-available metals and dominant P forms. We found that P inputs in the catchment originated mainly from domestic wastewater as evidenced by high concentrations of Cl (36-144 mg L-1), HCO3 and other cations in the channels. Most P discharged during low flow conditions was particulate implying that much of it was retained in bed sediments. Retained P was mostly bound to Ca and Fe/Al oxides. Hence, we inferred that mineral precipitation and adsorption to Ca-minerals were the dominant P retention processes. Bed sediments were P-saturated and showed a tendency to release P to discharging waters. P released was likely due to Ca-bound P because of the strong correlation between Ca and total P in sediments (r2 = 0.9). High flows exhibited a strong flush of PP and SS implying that part of P retained was frequently flushed out of the catchment by surface erosion and resuspension of bed sediment. Our findings suggest that P accumulated in the channel bed during low flows and then was slowly released into surface water. Hence, it will likely take some time, even with improved wastewater management practices, before P loads to downstream areas can be significantly reduced.

The effect of composition, size, and solubility on acute pulmonary injury in rats following exposure to Mexico city ambient particulate matter samples.

PubMed

Snow, Samantha J; De Vizcaya-Ruiz, Andrea; Osornio-Vargas, Alvaro; Thomas, Ronald F; Schladweiler, Mette C; McGee, John; Kodavanti, Urmila P

2014-01-01

Particulate matter (PM)-associated metals can contribute to adverse cardiopulmonary effects following exposure to air pollution. The aim of this study was to investigate how variation in the composition and size of ambient PM collected from two distinct regions in Mexico City relates to toxicity differences. Male Wistar Kyoto rats (14 wk) were intratracheally instilled with chemically characterized PM10 and PM2.5 from the north and PM10 from the south of Mexico City (3 mg/kg). Both water-soluble and acid-leachable fractions contained several metals, with levels generally higher in PM10 South. The insoluble and total, but not soluble, fractions of all PM induced pulmonary damage that was indicated by significant increases in neutrophilic inflammation, and several lung injury biomarkers including total protein, albumin, lactate dehydrogenase activity, and γ-glutamyl transferase activity 24 and 72 h postexposure. PM10 North and PM2.5 North also significantly decreased levels of the antioxidant ascorbic acid. Elevation in lung mRNA biomarkers of inflammation (tumor necrosis factor [TNF]-α and macrophage inflammatory protein [MIP]-2), oxidative stress (heme oxygenase [HO]-1, lectin-like oxidized low-density lipoprotein receptor [LOX]-1, and inducibile nitric oxide synthase [iNOS]), and thrombosis (tissue factor [TF] and plasminogen activator inhibitor [PAI]-1), as well as reduced levels of fibrinolytic protein tissue plasminogen activator (tPA), further indicated pulmonary injury following PM exposure. These responses were more pronounced with PM10 South (PM10 South > PM10 North > PM2.5 North), which contained higher levels of redox-active transition metals that may have contributed to specific differences in selected lung gene markers. These findings provide evidence that surface chemistry of the PM core and not the water-soluble fraction played an important role in regulating in vivo pulmonary toxicity responses to Mexico City PM.

Particulate Emissions from a Stationary Engine Fueled with Ultra-Low-Sulfur Diesel and Waste-Cooking-Oil-Derived Biodiesel.

PubMed

Betha, Raghu; Balasubramanian, Rajasekhar

2011-10-01

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture. [Box: see text].