Systems and economic analysis of microalgae ponds for conversion of CO{sub 2} to biomass. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benemann, J.R.; Oswald, W.J.

There is growing evidence that global warming could become a major global environmental threat during the 21st century. The precautionary principle commands preventive action, at both national and international levels, to minimize this potential threat. Many near-term, relatively inexpensive, mitigation options are available. In addition, long-term research is required to evaluate and develop advanced, possibly more expensive, countermeasures, in the eventuality that they may be required. The utilization of power plant CO{sub 2} and its recycling into fossil fuel substitutes by microalgae cultures could be one such long-term technology. Microalgae production is an expanding industry in the U.S., with threemore » commercial systems (of approximately 10 hectare each) producing nutriceuticals, specifically beta-carotene, extracted from Dunaliella, and Spirulina biomass. Microalgae are also used in wastewater treatment. Currently production costs are high, about $10,000/ton of algal biomass, almost two orders of magnitude higher than acceptable for greenhouse gas mitigation. This report reviews the current state-of-the-art, including algal cultivation and harvesting-processing, and outlines a technique for achieving very high productivities. Costs of CO{sub 2} mitigation with microalgae production of oils ({open_quotes}biodiesel{close_quotes}) are estimated and future R&D needs outlined.« less

The impact of environmental factors on carbon dioxide fixation by microalgae.

PubMed

Morales, Marcia; Sánchez, León; Revah, Sergio

2018-02-01

Microalgae are among the most productive biological systems for converting sunlight into chemical energy, which is used to capture and transform inorganic carbon into biomass. The efficiency of carbon dioxide capture depends on the cultivation system configuration (photobioreactors or open systems) and can vary according to the state of the algal physiology, the chemical composition of the nutrient medium, and environmental factors such as irradiance, temperature and pH. This mini-review is focused on some of the most important environmental factors determining photosynthetic activity, carbon dioxide biofixation, cell growth rate and biomass productivity by microalgae. These include carbon dioxide and O2 concentrations, light intensity, cultivation temperature and nutrients. Finally, a review of the operation of microalgal cultivation systems outdoors is presented as an example of the impact of environmental conditions on biomass productivity and carbon dioxide fixation. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Biofouling in photobioreactors for marine microalgae.

PubMed

Zeriouh, Ouassim; Reinoso-Moreno, José Vicente; López-Rosales, Lorenzo; Cerón-García, María Del Carmen; Sánchez-Mirón, Asterio; García-Camacho, Francisco; Molina-Grima, Emilio

2017-12-01

The economic and/or energetic feasibility of processes based on using microalgae biomass requires an efficient cultivation system. In photobioreactors (PBRs), the adhesion of microalgae to the transparent PBR surfaces leads to biofouling and reduces the solar radiation penetrating the PBR. Light reduction within the PBR decreases biomass productivity and, therefore, the photosynthetic efficiency of the cultivation system. Additionally, PBR biofouling leads to a series of further undesirable events including changes in cell pigmentation, culture degradation, and contamination by invasive microorganisms; all of which can result in the cultivation process having to be stopped. Designing PBR surfaces with proper materials, functional groups or surface coatings, to prevent microalgal adhesion is essential for solving the biofouling problem. Such a significant advance in microalgal biotechnology would enable extended operational periods at high productivity and reduce maintenance costs. In this paper, we review the few systematic studies performed so far and applied the existing thermodynamic and colloidal theories for microbial biofouling formation in order to understand microalgal adhesion on PBR surfaces and the microalgae-microalgae cell interactions. Their relationship to the physicochemical properties of the solid PBR surface, the microalgae cell surfaces, and the ionic strength of the culture medium is discussed. The suitability and the applicability of such theories are reviewed. To this end, an example of biofouling formation on a commercial glass surface is presented for the marine microalgae Nannochloropsis gaditana. It highlights the adhesion dynamics and the inaccuracies of the process and the need for further refinement of previous theories so as to apply them to flowing systems, such as is the case for PBRs used to culture microalgae.

Improving carbohydrate production of Chlorella sorokiniana NIES-2168 through semi-continuous process coupled with mixotrophic cultivation.

PubMed

Wang, Yue; Chiu, Sheng-Yi; Ho, Shih-Hsin; Liu, Zhuo; Hasunuma, Tomohisa; Chang, Ting-Ting; Chang, Kuan-Fu; Chang, Jo-Shu; Ren, Nan-Qi; Kondo, Akihiko

2016-08-01

Biofuels from microalgae is now a hot issue of great potential. However, achieving high starch productivity with photoautotrophic microalgae is still challenging. A feasible approach to enhance the growth and target product of microalgae is to conduct mixotrophic cultivation. The appropriate acetate addition combined with CO2 supply as dual carbon sources (i.e., mixotrophic cultivation) could enhance the cell growth of some microalgae species, but the effect of acetate-mediated mixotrophic culture mode on carbohydrate accumulation in microalgae remains unclear. Moreover, there is still lack of the information concerning how to increase the productivity of carbohydrates from microalgae under acetate-amended mixotrophic cultivation and how to optimize the engineering strategies to achieve the goal. This study was undertaken to develop an optimal acetate-contained mixotrophic cultivation system coupled with effective operation strategies to markedly improve the carbohydrate productivity of Chlorella sorokiniana NIES-2168. The optimal carbohydrate productivity of 695 mg/L/d was obtained, which is the highest value ever reported. The monosaccharide in the accumulated carbohydrates is mainly glucose (i.e., 85-90%), which is very suitable for bio-alcohols fermentation. Hence, by applying the optimal process developed in this study, C. sorokiniana NIES-2168 has a high potential to serve as a feedstock for subsequent biofuels conversion. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Autotrophic and heterotrophic microalgae and cyanobacteria cultivation for food and feed: life cycle assessment.

PubMed

Smetana, Sergiy; Sandmann, Michael; Rohn, Sascha; Pleissner, Daniel; Heinz, Volker

2017-12-01

The lack of protein sources in Europe could be reduced with onsite production of microalgae with autotrophic and heterotrophic systems, owing the confirmation of economic and environmental benefits. This study aimed at the life cycle assessment (LCA) of microalgae and cyanobacteria cultivation (Chlorella vulgaris and Arthrospira platensis) in autotrophic and heterotrophic conditions on a pilot industrial scale (in model conditions of Berlin, Germany) with further biomass processing for food and feed products. The comparison of analysis results with traditional benchmarks (protein concentrates) indicated higher environmental impact of microalgae protein powders. However high-moisture extrusion of heterotrophic cultivated C. vulgaris resulted in more environmentally sustainable product than pork and beef. Further optimization of production with Chlorella pyrenoidosa on hydrolyzed food waste could reduce environmental impact in 4.5 times and create one of the most sustainable sources of proteins. Copyright © 2017 Elsevier Ltd. All rights reserved.

Global evaluation of biofuel potential from microalgae

PubMed Central

Moody, Jeffrey W.; McGinty, Christopher M.; Quinn, Jason C.

2014-01-01

In the current literature, the life cycle, technoeconomic, and resource assessments of microalgae-based biofuel production systems have relied on growth models extrapolated from laboratory-scale data, leading to a large uncertainty in results. This type of simplistic growth modeling overestimates productivity potential and fails to incorporate biological effects, geographical location, or cultivation architecture. This study uses a large-scale, validated, outdoor photobioreactor microalgae growth model based on 21 reactor- and species-specific inputs to model the growth of Nannochloropsis. This model accurately accounts for biological effects such as nutrient uptake, respiration, and temperature and uses hourly historical meteorological data to determine the current global productivity potential. Global maps of the current near-term microalgae lipid and biomass productivity were generated based on the results of annual simulations at 4,388 global locations. Maximum annual average lipid yields between 24 and 27 m3·ha−1·y−1, corresponding to biomass yields of 13 to 15 g·m−2·d−1, are possible in Australia, Brazil, Colombia, Egypt, Ethiopia, India, Kenya, and Saudi Arabia. The microalgae lipid productivity results of this study were integrated with geography-specific fuel consumption and land availability data to perform a scalability assessment. Results highlight the promising potential of microalgae-based biofuels compared with traditional terrestrial feedstocks. When water, nutrients, and CO2 are not limiting, many regions can potentially meet significant fractions of their transportation fuel requirements through microalgae production, without land resource restriction. Discussion focuses on sensitivity of monthly variability in lipid production compared with annual average yields, effects of temperature on productivity, and a comparison of results with previous published modeling assumptions. PMID:24912176

Mixotrophic cultivation of microalgae for biodiesel production: status and prospects.

PubMed

Wang, Jinghan; Yang, Haizhen; Wang, Feng

2014-04-01

Biodiesel from microalgae provides a promising alternative for biofuel production. Microalgae can be produced under three major cultivation modes, namely photoautotrophic cultivation, heterotrophic cultivation, and mixotrophic cultivation. Potentials and practices of biodiesel production from microalgae have been demonstrated mostly focusing on photoautotrophic cultivation; mixotrophic cultivation of microalgae for biodiesel production has rarely been reviewed. This paper summarizes the mechanisms and virtues of mixotrophic microalgae cultivation through comparison with other major cultivation modes. Influencing factors of microalgal biodiesel production under mixotrophic cultivation are presented, development of combining microalgal biodiesel production with wastewater treatment is especially reviewed, and bottlenecks and strategies for future commercial production are also identified.

Sustainability and economic evaluation of microalgae grown in brewery wastewater.

PubMed

Mata, Teresa M; Mendes, Adélio M; Caetano, Nídia S; Martins, António A

2014-09-01

This article evaluates the sustainability and economic potential of microalgae grown in brewery wastewater for biodiesel and biomass production. Three sustainability and two economic indicators were considered in the evaluation within a life cycle perspective. For the production system the most efficient process units were selected. Results show that harvesting and oil separation are the main process bottlenecks. Microalgae with higher lipid content and productivity are desirable for biodiesel production, although comparable to other biofuel's feedstock concerning sustainability. However, improvements are still needed to reach the performance level of fossil diesel. Profitability reaches a limit for larger cultivation areas, being higher when extracted biomass is sold together with microalgae oil, in which case the influence of lipid content and areal productivity is smaller. The values of oil and/or biomass prices calculated to ensure that the process is economically sound are still very high compared with other fuel options, especially biodiesel. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of temperature, CO2/O2 concentrations and light intensity on cellular multiplication of microalgae, Euglena gracilis

NASA Technical Reports Server (NTRS)

Kitaya, Y.; Azuma, H.; Kiyota, M.

2005-01-01

Microalgae culture is likely to play an important role in aquatic food production modules in bioregenerative systems for producing feeds for fish, converting CO2 to O2 and remedying water quality as well as aquatic higher plants. In the present study, the effects of culture conditions on the cellular multiplication of microalgae, Euglena gracilis, was investigated as a fundamental study to determine the optimum culture conditions for microalgae production in aquatic food production modules including both microalgae culture and fish culture systems. E. gracilis was cultured under conditions with five levels of temperatures (25-33 degrees C), three levels of CO2 concentrations (2-6%), five levels of O2 concentrations (10-30%), and six levels of photosynthetic photon flux (20-200 micromoles m-2 s-1). The number of Euglena cells in a certain volume of solution was monitored with a microscope under each environmental condition. The multiplication rate of the cells was highest at temperatures of 27-31 degrees C, CO2 concentration of 4%, O2 concentration of 20% and photosynthetic photon flux of about 100 micromoles m-2 s-1. The results demonstrate that E. gracilis could efficiently produce biomass and convert CO2 to O2 under relatively low light intensities in aquatic food production modules. c2005 Published by Elsevier Ltd on behalf of COSPAR.

Reducing the life cycle GHG emissions of microalgal biodiesel through integration with ethanol production system.

PubMed

Maranduba, Henrique Leonardo; Robra, Sabine; Nascimento, Iracema Andrade; da Cruz, Rosenira Serpa; Rodrigues, Luciano Brito; de Almeida Neto, José Adolfo

2015-10-01

Despite environmental benefits of algal-biofuels, the energy-intensive systems for producing microalgae-feedstock may result in high GHG emissions. Trying to overcome energy-costs, this research analyzed the biodiesel production system via dry-route, based on Chlorella vulgaris cultivated in raceways, by comparing the GHG-footprints of diverse microalgae-biodiesel scenarios. These involved: the single system of biomass production (C0); the application of pyrolysis on the residual microalgal biomass (cake) from the oil extraction process (C1); the same as C0, with anaerobic cake co-digested with cattle manure (C2); the same conditions as in C1 and C2, by integrating in both cases (respectively C3 and C4), the microalgae cultivation with an autonomous ethanol distillery. The reduction of GHG emissions in scenarios with no such integration (C1 and C2), compared to CO, was insignificant (0.53% and 4.67%, respectively), whereas in the scenarios with integration with ethanol production system, the improvements were 53.57% for C3 and 63.84% for C4. Copyright © 2015 Elsevier Ltd. All rights reserved.

Continuous culture methodology for the screening of microalgae for oil.

PubMed

Del Río, Esperanza; Armendáriz, Ana; García-Gómez, Elena; García-González, Mercedes; Guerrero, Miguel G

2015-02-10

A basic criterion in the selection of microalgae suitable as source of oil for biodiesel should be their actual capacity to produce lipids or, more properly, the fatty acid yield. Performance assessment of 10 preselected microalgae under both batch and continuous culture points to the latter approach as the most adequate for evaluating fatty acid productivity. Differences were patent in continuous culture among strains that otherwise had analogous oil accumulation potential under batch culture. Some promising strains under batch culture (like Muriella aurantiaca and Monoraphidium braunii) exhibited, however, values for actual fatty acid productivity lower than 40 mgL(-1)d(-1) in continuous regime. The analysis performed in photochemostat under continuous culture regime revealed the great potential of Chlorococcum olefaciens, Pseudokirchneriella subcapitata and Scenedesmus almeriensis as oil producing microalgae. Fatty acid productivity levels over 90 mgL(-1)d(-1) were recorded for the latter strains under moderate nitrogen limitation, conditions which led to an enrichment in saturated and monounsaturated fatty acids, a more suitable profile as raw material for biodiesel. The continuous culture methodology employed represents a sound procedure for screening microalgae for biofuel production, providing a reliable evaluation of their fatty acid production capacity, under conditions close to those of outdoor production systems. Copyright © 2015 Elsevier B.V. All rights reserved.

Metabolic engineering of Cyanobacteria and microalgae for enhanced production of biofuels and high-value products.

PubMed

Gomaa, M A; Al-Haj, L; Abed, R M M

2016-10-01

A lot of research has been performed on Cyanobacteria and microalgae with the aim to produce numerous biotechnological products. However, native strains have a few shortcomings, like limitations in cultivation, harvesting and product extraction, which prevents reaching optimal production value at lowest costs. Such limitations require the intervention of genetic engineering to produce strains with superior properties. Promising advancements in the cultivation of Cyanobacteria and microalgae have been achieved by improving photosynthetic efficiency through increasing RuBisCO activity and truncation of light-harvesting antennae. Genetic engineering has also contributed to final product extraction by inducing autolysis and product secretory systems, to enable direct product recovery without going through costly extraction steps. In this review, we summarize the different enzymes and pathways that have been targeted thus far for improving cultivation aspects, harvesting and product extraction in Cyanobacteria and microalgae. With synthetic biology advancements, genetically engineered strains can be generated to resolve demanding process issues and achieve economic practicality. This comprehensive overview of gene modifications will be useful to researchers in the field to employ on their strains to increase their yields and improve the economic feasibility of the production process. © 2016 The Society for Applied Microbiology.

Biosequestration of atmospheric CO2 and flue gas-containing CO2 by microalgae.

PubMed

Cheah, Wai Yan; Show, Pau Loke; Chang, Jo-Shu; Ling, Tau Chuan; Juan, Joon Ching

2015-05-01

The unceasing rise of greenhouse gas emission has led to global warming and climate change. Global concern on this phenomenon has put forward the microalgal-based CO2 sequestration aiming to sequester carbon back to the biosphere, ultimately reducing greenhouse effects. Microalgae have recently gained enormous attention worldwide, to be the valuable feedstock for renewable energy production, due to their high growth rates, high lipid productivities and the ability to sequester carbon. The photosynthetic process of microalgae uses atmospheric CO2 and CO2 from flue gases, to synthesize nutrients for their growth. In this review article, we will primarily discuss the efficiency of CO2 biosequestration by microalgae species, factors influencing microalgal biomass productions, microalgal cultivation systems, the potential and limitations of using flue gas for microalgal cultivation as well as the bio-refinery approach of microalgal biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

Harvesting of microalgae biomass from the phycoremediation process of greywater.

PubMed

Atiku, Hauwa; Mohamed, R M S R; Al-Gheethi, A A; Wurochekke, A A; Kassim, Amir Hashim M

2016-12-01

The wide application of microalgae in the field of wastewater treatment and bioenergy source has improved research studies in the past years. Microalgae represent a good source of biomass and bio-products which are used in different medical and industrial activities, among them the production of high-valued products and biofuels. The present review focused on greywater treatment through the application of phycoremediation technique with microalgae and presented recent advances in technologies used for harvesting the microalgae biomass. The advantages and disadvantages of each method are discussed. The microbiological aspects of production, harvesting and utilization of microalgae biomass are viewed.

Sustainable production of toxin free marine microalgae biomass as fish feed in large scale open system in the Qatari desert.

PubMed

Das, Probir; Thaher, Mahmoud Ibrahim; Hakim, Mohammed Abdul Quadir Mohd Abdul; Al-Jabri, Hareb Mohammed S J

2015-09-01

Mass cultivation of microalgae biomass for feed should be cost effective and toxin free. Evaporation loss in Qatar can be as high as 2 cm/d. Hence, production of marine microalgae biomass in Qatar would also require mitigating water loss as there was only very limited groundwater reserve. To address these issues, a combination of four growth conditions were applied to a 25,000 L raceway pond: locally isolated microalgae strain was selected which could grow in elevated salinity; strain that did not require silica and vitamins; volume of the culture would increase over time keeping denser inoculum in the beginning, and evaporation water loss would be balanced by adding seawater only. A local saline tolerant Nannochloropsis sp. was selected which did not require silica and vitamins. When the above conditions were combined in the pond, average areal biomass productivities reached 20.37 g/m(2)/d, and the culture was not contaminated by any toxic microalgae. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimization of Biofuel Production From Transgenic Microalgae

DTIC Science & Technology

2013-02-27

AFRL-OSR-VA-TR-2013-0145 OPTIMIZATION OF BIOFUEL PRODUCTION FROM TRANSGENIC MICROALGAE Richard Sayre Donald Danforth...Technical 20080815 to 20120630 OPTIMIZATION OF BIOFUEL PRODUCTION FROM TRANSGENIC MICROALGAE FA9550-08-1-0451 Richard Sayre Donald Danforth Plant...BIOFUEL PRODUCTION FROM TRANSGENIC MICROALGAE Grant/Contract Number: FA9550-08-1-0451 Reporting Period: Final Report Abstract: We have compared the

Development of a Two-Stage Microalgae Dewatering Process – A Life Cycle Assessment Approach

PubMed Central

Soomro, Rizwan R.; Zeng, Xianhai; Lu, Yinghua; Lin, Lu; Danquah, Michael K.

2016-01-01

Even though microalgal biomass is leading the third generation biofuel research, significant effort is required to establish an economically viable commercial-scale microalgal biofuel production system. Whilst a significant amount of work has been reported on large-scale cultivation of microalgae using photo-bioreactors and pond systems, research focus on establishing high performance downstream dewatering operations for large-scale processing under optimal economy is limited. The enormous amount of energy and associated cost required for dewatering large-volume microalgal cultures has been the primary hindrance to the development of the needed biomass quantity for industrial-scale microalgal biofuels production. The extremely dilute nature of large-volume microalgal suspension and the small size of microalgae cells in suspension create a significant processing cost during dewatering and this has raised major concerns towards the economic success of commercial-scale microalgal biofuel production as an alternative to conventional petroleum fuels. This article reports an effective framework to assess the performance of different dewatering technologies as the basis to establish an effective two-stage dewatering system. Bioflocculation coupled with tangential flow filtration (TFF) emerged a promising technique with total energy input of 0.041 kWh, 0.05 kg CO2 emissions and a cost of $ 0.0043 for producing 1 kg of microalgae biomass. A streamlined process for operational analysis of two-stage microalgae dewatering technique, encompassing energy input, carbon dioxide emission, and process cost, is presented. PMID:26904075

The promising future of microalgae: current status, challenges, and optimization of a sustainable and renewable industry for biofuels, feed, and other products.

PubMed

Khan, Muhammad Imran; Shin, Jin Hyuk; Kim, Jong Deog

2018-03-05

Microalgae have recently attracted considerable interest worldwide, due to their extensive application potential in the renewable energy, biopharmaceutical, and nutraceutical industries. Microalgae are renewable, sustainable, and economical sources of biofuels, bioactive medicinal products, and food ingredients. Several microalgae species have been investigated for their potential as value-added products with remarkable pharmacological and biological qualities. As biofuels, they are a perfect substitute to liquid fossil fuels with respect to cost, renewability, and environmental concerns. Microalgae have a significant ability to convert atmospheric CO 2 to useful products such as carbohydrates, lipids, and other bioactive metabolites. Although microalgae are feasible sources for bioenergy and biopharmaceuticals in general, some limitations and challenges remain, which must be overcome to upgrade the technology from pilot-phase to industrial level. The most challenging and crucial issues are enhancing microalgae growth rate and product synthesis, dewatering algae culture for biomass production, pretreating biomass, and optimizing the fermentation process in case of algal bioethanol production. The present review describes the advantages of microalgae for the production of biofuels and various bioactive compounds and discusses culturing parameters.

Microalgae biorefinery: High value products perspectives.

PubMed

Chew, Kit Wayne; Yap, Jing Ying; Show, Pau Loke; Suan, Ng Hui; Juan, Joon Ching; Ling, Tau Chuan; Lee, Duu-Jong; Chang, Jo-Shu

2017-04-01

Microalgae have received much interest as a biofuel feedstock in response to the uprising energy crisis, climate change and depletion of natural sources. Development of microalgal biofuels from microalgae does not satisfy the economic feasibility of overwhelming capital investments and operations. Hence, high-value co-products have been produced through the extraction of a fraction of algae to improve the economics of a microalgae biorefinery. Examples of these high-value products are pigments, proteins, lipids, carbohydrates, vitamins and anti-oxidants, with applications in cosmetics, nutritional and pharmaceuticals industries. To promote the sustainability of this process, an innovative microalgae biorefinery structure is implemented through the production of multiple products in the form of high value products and biofuel. This review presents the current challenges in the extraction of high value products from microalgae and its integration in the biorefinery. The economic potential assessment of microalgae biorefinery was evaluated to highlight the feasibility of the process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Microalgae for high-value compounds and biofuels production: a review with focus on cultivation under stress conditions.

PubMed

Markou, Giorgos; Nerantzis, Elias

2013-12-01

Microalgal biomass as feedstock for biofuel production is an attracting alternative to terrestrial plant utilization for biofuels production. However, today the microalgal cultivation systems for energy production purposes seem not yet to be economically feasible. Microalgae, though cultivated under stress conditions, such as nutrient starvation, high salinity, high temperature etc. accumulate considerable amounts (up to 60-65% of dry weight) of lipids or carbohydrates along with several secondary metabolites. Especially some of the latter are valuable compounds with an enormous range of industrial applications. The simultaneous production of lipids or carbohydrates for biofuel production and of secondary metabolites in a biorefinery concept might allow the microalgal production to be economically feasible. This paper aims to provide a review on the available literature about the cultivation of microalgae for the accumulation of high-value compounds along with lipids or carbohydrates focusing on stress cultivation conditions. © 2013.

Biotechnological production of value-added carotenoids from microalgae: Emerging technology and prospects.

PubMed

Wichuk, Kristine; Brynjólfsson, Sigurður; Fu, Weiqi

2014-01-01

We recently evaluated the relationship between abiotic environmental stresses and lutein biosynthesis in the green microalga Dunaliella salina and suggested a rational design of stress-driven adaptive evolution experiments for carotenoids production in microalgae. Here, we summarize our recent findings regarding the biotechnological production of carotenoids from microalgae and outline emerging technology in this field. Carotenoid metabolic pathways are characterized in several representative algal species as they pave the way for biotechnology development. The adaptive evolution strategy is highlighted in connection with enhanced growth rate and carotenoid metabolism. In addition, available genetic modification tools are described, with emphasis on model species. A brief discussion on the role of lights as limiting factors in carotenoid production in microalgae is also included. Overall, our analysis suggests that light-driven metabolism and the photosynthetic efficiency of microalgae in photobioreactors are the main bottlenecks in enhancing biotechnological potential of carotenoid production from microalgae.

Outdoor cultivation of microalgae for carotenoid production: current state and perspectives.

PubMed

Del Campo, José A; García-González, Mercedes; Guerrero, Miguel G

2007-04-01

Microalgae are a major natural source for a vast array of valuable compounds, including a diversity of pigments, for which these photosynthetic microorganisms represent an almost exclusive biological resource. Yellow, orange, and red carotenoids have an industrial use in food products and cosmetics as vitamin supplements and health food products and as feed additives for poultry, livestock, fish, and crustaceans. The growing worldwide market value of carotenoids is projected to reach over US$1,000 million by the end of the decade. The nutraceutical boom has also integrated carotenoids mainly on the claim of their proven antioxidant properties. Recently established benefits in human health open new uses for some carotenoids, especially lutein, an effective agent for the prevention and treatment of a variety of degenerative diseases. Consumers' demand for natural products favors development of pigments from biological sources, thus increasing opportunities for microalgae. The biotechnology of microalgae has gained considerable progress and relevance in recent decades, with carotenoid production representing one of its most successful domains. In this paper, we review the most relevant features of microalgal biotechnology related to the production of different carotenoids outdoors, with a main focus on beta-carotene from Dunaliella, astaxanthin from Haematococcus, and lutein from chlorophycean strains. We compare the current state of the corresponding production technologies, based on either open-pond systems or closed photobioreactors. The potential of scientific and technological advances for improvements in yield and reduction in production costs for carotenoids from microalgae is also discussed.

Rationales and Approaches for Studying Metabolism in Eukaryotic Microalgae

PubMed Central

Veyel, Daniel; Erban, Alexander; Fehrle, Ines; Kopka, Joachim; Schroda, Michael

2014-01-01

The generation of efficient production strains is essential for the use of eukaryotic microalgae for biofuel production. Systems biology approaches including metabolite profiling on promising microalgal strains, will provide a better understanding of their metabolic networks, which is crucial for metabolic engineering efforts. Chlamydomonas reinhardtii represents a suited model system for this purpose. We give an overview to genetically amenable microalgal strains with the potential for biofuel production and provide a critical review of currently used protocols for metabolite profiling on Chlamydomonas. We provide our own experimental data to underpin the validity of the conclusions drawn. PMID:24957022

New challenges in microalgae biotechnology.

PubMed

Valverde, Federico; Romero-Campero, Francisco J; León, Rosa; Guerrero, Miguel G; Serrano, Aurelio

2016-08-01

Photosynthetic protists, also called microalgae, have been systematically studied for more than a century. However, only recently broad biotechnological applications have fostered a novel wave of research on their potentialities as sustainable resources of renewable energy as well as valuable industrial and agro-food products. At the recent VII European Congress of Protistology held in Seville, three outstanding examples of different research strategies on microalgae with biotechnological implications were presented, which suggested that integrative approaches will produce very significant advances in this field in the next future. In any case, intense research and the application of systems biology and genetic engineering techniques are absolutely essential to reach the full potential of microalgae as cell-factories of bio-based products and, therefore, could contribute significantly to solve the problems of biosustainability and energy shortage. Copyright © 2016 Elsevier GmbH. All rights reserved.

Flashing light in microalgae biotechnology.

PubMed

Abu-Ghosh, Said; Fixler, Dror; Dubinsky, Zvy; Iluz, David

2016-03-01

Flashing light can enhance photosynthesis and improve the quality and quantity of microalgal biomass, as it can increase the products of interest by magnitudes. Therefore, the integration of flashing light effect into microalgal cultivation systems should be considered. However, microalgae require a balanced mix of the light/dark cycle for higher growth rates, and respond to light intensity differently according to the pigments acquired or lost during the growth. This review highlights recently published results on flashing light effect on microalgae and its applications in biotechnology, as well as the recently developed bioreactors designed to fulfill this effect. It also discusses how this knowledge can be applied in selecting the optimal light frequencies and intensities with specific technical properties for increasing biomass production and/or the yield of the chemicals of interest by microalgae belonging to different genera. Copyright © 2015 Elsevier Ltd. All rights reserved.

Geoengineering, marine microalgae, and climate stabilization in the 21st century

NASA Astrophysics Data System (ADS)

Greene, Charles H.; Huntley, Mark E.; Archibald, Ian; Gerber, Léda N.; Sills, Deborah L.; Granados, Joe; Beal, Colin M.; Walsh, Michael J.

2017-03-01

Society has set ambitious targets for stabilizing mean global temperature. To attain these targets, it will have to reduce CO2 emissions to near zero by mid-century and subsequently remove CO2 from the atmosphere during the latter half of the century. There is a recognized need to develop technologies for CO2 removal; however, attempts to develop direct air-capture systems have faced both energetic and financial constraints. Recently, BioEnergy with Carbon Capture and Storage (BECCS) has emerged as a leading candidate for removing CO2 from the atmosphere. However, BECCS can have negative consequences on land, nutrient, and water use as well as biodiversity and food production. Here, we describe an alternative approach based on the large-scale industrial production of marine microalgae. When cultivated with proper attention to power, carbon, and nutrient sources, microalgae can be processed to produce a variety of biopetroleum products, including carbon-neutral biofuels for the transportation sector and long-lived, potentially carbon-negative construction materials for the built environment. In addition to these direct roles in mitigating and potentially reversing the effects of fossil CO2 emissions, microalgae can also play an important indirect role. As microalgae exhibit much higher primary production rates than terrestrial plants, they require much less land area to produce an equivalent amount of bioenergy and/or food. On a global scale, the avoided emissions resulting from displacement of conventional agriculture may exceed the benefits of microalgae biofuels in achieving the climate stabilization goals.

Impact of Microalgae-Bacteria Interactions on the Production of Algal Biomass and Associated Compounds

PubMed Central

Fuentes, Juan Luis; Garbayo, Inés; Cuaresma, María; Montero, Zaida; González-del-Valle, Manuel; Vílchez, Carlos

2016-01-01

A greater insight on the control of the interactions between microalgae and other microorganisms, particularly bacteria, should be useful for enhancing the efficiency of microalgal biomass production and associated valuable compounds. Little attention has been paid to the controlled utilization of microalgae-bacteria consortia. However, the studies of microalgal-bacterial interactions have revealed a significant impact of the mutualistic or parasitic relationships on algal growth. The algal growth, for instance, has been shown to be enhanced by growth promoting factors produced by bacteria, such as indole-3-acetic acid. Vitamin B12 produced by bacteria in algal cultures and bacterial siderophores are also known to be involved in promoting faster microalgal growth. More interestingly, enhancement in the intracellular levels of carbohydrates, lipids and pigments of microalgae coupled with algal growth stimulation has also been reported. In this sense, massive algal production might occur in the presence of bacteria, and microalgae-bacteria interactions can be beneficial to the massive production of microalgae and algal products. This manuscript reviews the recent knowledge on the impact of the microalgae-bacteria interactions on the production of microalgae and accumulation of valuable compounds, with an emphasis on algal species having application in aquaculture. PMID:27213407

Experimental biological life support system. I. Continuous cultivation of algae as a link of a closed ecosystem.

PubMed

Kirensky, L V; Terskov, I A; Gitelson, I I; Lisovsky, G M; Kovrov, B G; Okladnikov, Y N

1968-01-01

According to the opinion of many researchers, a culture of microalgae may serve as a regenerator of atmosphere in the cabin of a spaceship. To use microalgae for these objectives, it was necessary to have an automatic unit possessing a high productivity of the cultivation process. This unit, containing a minimum of equipment, enables carrying on for an unlimited time the cultivation of algae without a drop in their productivity. The unit meeting these requirements (the cultivator) was developed by the authors and will be described in the presentation. The stability of the microalga photosynthetic system is characterized by the fact that after 70% biosynthesis repression by the ultraviolet radiation, a full regeneration of the productivity level takes place within 24 hours. In our experiments the system was functioning with the stable estimated productivity for many days (up to two months without interruption). During the process, no biological inhibitions to permanent performance and further prolongation of its life were found. As to the productivity, stability and control, the described biotechnological method may appear to be useful as a link of the closed ecosystem.

Coordinated regulation of nitrogen supply mode and initial cell density for energy storage compounds production with economized nitrogen utilization in a marine microalga Isochrysis zhangjiangensis.

PubMed

Chi, Lei; Yao, Changhong; Cao, Xupeng; Xue, Song

2016-01-01

Lipids and carbohydrates are main energy storage compounds (ESC) of microalgae under stressed conditions and they are potential feedstock for biofuel production. Yet, the sustainable and commercially successful production of ESC in microalgae needs to consider nitrogen utilization efficiency. Here the impact of different initial cell densities (ICDs) on ESC accumulation in Isochrysis zhangjiangensis under two nitrogen supply modes (an initially equal concentration of nitrogen per-cell in the medium (N1) and an equal total concentration of nitrogen in the culture system (N2)) were investigated. The results demonstrated that the highest ESC yield (1.36gL(-1)) at N1, which included a maximal nitrogen supply in the cultivation system, and the highest ESC content (66.5%) and ESC productivity per mass of nitrogen (3.28gg(-1) (N) day(-1)) at N2, were all obtained under a high ICD of 8.0×10(6)cellsmL(-1). Therefore I. zhangjiangensis qualifies for ESC-enriched biomass production with economized nitrogen utilization. Copyright © 2015 Elsevier Ltd. All rights reserved.

A geographical assessment of vegetation carbon stocks and greenhouse gas emissions on potential microalgae-based biofuel facilities in the United States.

PubMed

Quiroz Arita, Carlos; Yilmaz, Özge; Barlak, Semin; Catton, Kimberly B; Quinn, Jason C; Bradley, Thomas H

2016-12-01

The microalgae biofuels life cycle assessments (LCA) present in the literature have excluded the effects of direct land use change (DLUC) from facility construction under the assumption that DLUC effects are negligible. This study seeks to model the greenhouse gas (GHG) emissions of microalgae biofuels including DLUC by quantifying the CO 2 equivalence of carbon released to the atmosphere through the construction of microalgae facilities. The locations and types of biomass and Soil Organic Carbon that are disturbed through microalgae cultivation facility construction are quantified using geographical models of microalgae productivity potential including consideration of land availability. The results of this study demonstrate that previous LCA of microalgae to biofuel processes have overestimated GHG benefits of microalgae-based biofuels production by failing to include the effect of DLUC. Previous estimations of microalgae biofuel production potential have correspondingly overestimated the volume of biofuels that can be produced in compliance with U.S. environmental goals. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fermentative hydrogen production using pretreated microalgal biomass as feedstock.

PubMed

Wang, Jianlong; Yin, Yanan

2018-02-14

Microalgae are simple chlorophyll containing organisms, they have high photosynthetic efficiency and can synthesize and accumulate large quantities of carbohydrate biomass. They can be cultivated in fresh water, seawater and wastewater. They have been used as feedstock for producing biodiesel, bioethanol and biogas. The production of these biofuels can be integrated with CO 2 mitigation, wastewater treatment, and the production of high-value chemicals. Biohydrogen from microalgae is renewable. Microalgae have several advantages compared to terrestrial plants, such as higher growth rate with superior CO 2 fixation capacity; they do not need arable land to grow; they do not contain lignin. In this review, the biology of microalgae and the chemical composition of microalgae were briefly introduced, the advantages and disadvantages of hydrogen production from microalgae were discussed, and the pretreatment of microalgal biomass and the fermentative hydrogen production from microalgal biomass pretreated by different methods (including physical, chemical, biological and combined methods) were summarized and evaluated. For the production of biohydrogen from microalgae, the economic feasibility remains the most important aspect to consider. Several technological and economic issues must be addressed to achieve success on a commercial scale.

Ultrasonic assisted biodiesel production of microalgae by direct transesterification

NASA Astrophysics Data System (ADS)

Kalsum, Ummu; Mahfud, Mahfud; Roesyadi, Achmad

2017-03-01

Microalgae are considered as the third generation source of biofuel and an excellent candidate for biofuel production to replace the fossil energy. The use of ultrasonic in producing biodiesel by direct transesterification of Nannochloropsis occulata using KOH as catalyst and methanol as a solvent was investigated. The following condition were determined as an optimum by experimental evaluates:: 1: 15 microalga to methanol (molar ratio); 3% catalyst concentration at temperature 40°C after 30 minute of ultrasonication. The highest yield of biodiesel produced was 30.3%. The main components of methyl ester from Nannochloropsis occulata were palmitic (C16 :0),, oleic (C18:1), stearic (C18;0), arahidic (C20:0) and myristic (C14:0). This stated that the application of ultrasounic for direct transesterificaiton of microalgae effectively reduced the reaction time compared to the reported values of conventional heating systems.

Techno-economic and Monte Carlo probabilistic analysis of microalgae biofuel production system.

PubMed

Batan, Liaw Y; Graff, Gregory D; Bradley, Thomas H

2016-11-01

This study focuses on the characterization of the technical and economic feasibility of an enclosed photobioreactor microalgae system with annual production of 37.85 million liters (10 million gallons) of biofuel. The analysis characterizes and breaks down the capital investment and operating costs and the production cost of unit of algal diesel. The economic modelling shows total cost of production of algal raw oil and diesel of $3.46 and $3.69 per liter, respectively. Additionally, the effects of co-products' credit and their impact in the economic performance of algal-to-biofuel system are discussed. The Monte Carlo methodology is used to address price and cost projections and to simulate scenarios with probabilities of financial performance and profits of the analyzed model. Different markets for allocation of co-products have shown significant shifts for economic viability of algal biofuel system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Growth and fatty acid characterization of microalgae isolated from municipal waste-treatment systems and the potential role of algal-associated bacteria in feedstock production

PubMed Central

Stemmler, Kevin; Massimi, Rebecca

2016-01-01

Much research has focused on growing microalgae for biofuel feedstock, yet there remain concerns about the feasibility of freshwater feedstock systems. To reduce cost and improve environmental sustainability, an ideal microalgal feedstock system would be fed by municipal, agricultural or industrial wastewater as a main source of water and nutrients. Nonetheless, the microalgae must also be tolerant of fluctuating wastewater quality, while still producing adequate biomass and lipid yields. To address this problem, our study focused on isolating and characterizing microalgal strains from three municipal wastewater treatment systems (two activated sludge and one aerated-stabilization basin systems) for their potential use in biofuel feedstock production. Most of the 19 isolates from wastewater grew faster than two culture collection strains under mixotrophic conditions, particularly with glucose. The fastest growing wastewater strains included the genera Chlorella and Dictyochloris. The fastest growing microalgal strains were not necessarily the best lipid producers. Under photoautotrophic and mixotrophic growth conditions, single strains of Chlorella and Scenedesmus each produced the highest lipid yields, including those most relevant to biodiesel production. A comparison of axenic and non-axenic versions of wastewater strains showed a notable effect of commensal bacteria on fatty acid composition. Strains grown with bacteria tended to produce relatively equal proportions of saturated and unsaturated fatty acids, which is an ideal lipid blend for biodiesel production. These results not only show the potential for using microalgae isolated from wastewater for growth in wastewater-fed feedstock systems, but also the important role that commensal bacteria may have in impacting the fatty acid profiles of microalgal feedstock. PMID:26989618

Microalgae as sustainable renewable energy feedstock for biofuel production.

PubMed

Medipally, Srikanth Reddy; Yusoff, Fatimah Md; Banerjee, Sanjoy; Shariff, M

2015-01-01

The world energy crisis and increased greenhouse gas emissions have driven the search for alternative and environmentally friendly renewable energy sources. According to life cycle analysis, microalgae biofuel is identified as one of the major renewable energy sources for sustainable development, with potential to replace the fossil-based fuels. Microalgae biofuel was devoid of the major drawbacks associated with oil crops and lignocelluloses-based biofuels. Algae-based biofuels are technically and economically viable and cost competitive, require no additional lands, require minimal water use, and mitigate atmospheric CO2. However, commercial production of microalgae biodiesel is still not feasible due to the low biomass concentration and costly downstream processes. The viability of microalgae biodiesel production can be achieved by designing advanced photobioreactors, developing low cost technologies for biomass harvesting, drying, and oil extraction. Commercial production can also be accomplished by improving the genetic engineering strategies to control environmental stress conditions and by engineering metabolic pathways for high lipid production. In addition, new emerging technologies such as algal-bacterial interactions for enhancement of microalgae growth and lipid production are also explored. This review focuses mainly on the problems encountered in the commercial production of microalgae biofuels and the possible techniques to overcome these difficulties.

Microalgae as Sustainable Renewable Energy Feedstock for Biofuel Production

PubMed Central

Yusoff, Fatimah Md.; Shariff, M.

2015-01-01

The world energy crisis and increased greenhouse gas emissions have driven the search for alternative and environmentally friendly renewable energy sources. According to life cycle analysis, microalgae biofuel is identified as one of the major renewable energy sources for sustainable development, with potential to replace the fossil-based fuels. Microalgae biofuel was devoid of the major drawbacks associated with oil crops and lignocelluloses-based biofuels. Algae-based biofuels are technically and economically viable and cost competitive, require no additional lands, require minimal water use, and mitigate atmospheric CO2. However, commercial production of microalgae biodiesel is still not feasible due to the low biomass concentration and costly downstream processes. The viability of microalgae biodiesel production can be achieved by designing advanced photobioreactors, developing low cost technologies for biomass harvesting, drying, and oil extraction. Commercial production can also be accomplished by improving the genetic engineering strategies to control environmental stress conditions and by engineering metabolic pathways for high lipid production. In addition, new emerging technologies such as algal-bacterial interactions for enhancement of microalgae growth and lipid production are also explored. This review focuses mainly on the problems encountered in the commercial production of microalgae biofuels and the possible techniques to overcome these difficulties. PMID:25874216

Lipids rich in ω-3 polyunsaturated fatty acids from microalgae.

PubMed

Santos-Sánchez, N F; Valadez-Blanco, R; Hernández-Carlos, B; Torres-Ariño, A; Guadarrama-Mendoza, P C; Salas-Coronado, R

2016-10-01

Despite microalgae recently receiving enormous attention as a potential source of biodiesel, their use is still not feasible as an alternative to fossil fuels. Recently, interest in microalgae has focused on the production of bioactive compounds such as polyunsaturated fatty acids (PUFA), which provide microalgae a high added value. Several considerations need to be assessed for optimizing PUFA production from microalgae. Firstly, a microalgae species that produces high PUFA concentrations should be selected, such as Nannochloropsis gaditana, Isochrysis galbana, Phaeodactylum tricornutum, and Crypthecodinium cohnii, with marine species gaining more attention than do freshwater species. Closed cultivation processes, e.g., photobioreactors, are the most appropriate since temperature, pH, and nutrients can be controlled. An airlift column with LEDs or optical fibers to distribute photons into the culture media can be used at small scale to produce inoculum, while tubular and flat panels are used at commercial scale. Depending on the microalgae, a temperature range from 15 to 28 °C and a pH from 7 to 8 can be employed. Relevant conditions for PUFA production are medium light irradiances (50-300 μmol photons m(-2) s(-1)), air enriched with (0-1 % (v/v) CO2, as well as nitrogen and phosphorous limitation. For research purposes, the most appropriate medium for PUFA production is Bold's Basal, whereas mixotrophic cultivation using sucrose or glucose as the carbon source has been reported for industrial processes. For cell harvesting, the use of tangential flow membrane filtration or disk stack centrifugation is advisable at commercial scale. Current researches on PUFA extraction have focused on the use of organic solvents assisted with ultrasound or microwaves, supercritical fluids, and electroporation or are enzyme assisted. Commercial-scale extraction involves mainly physical methods such as bead mills and expeller presses. All these factors should be taken into account when choosing a PUFA production system, as discussed in this review.

Algal biofuels: challenges and opportunities.

PubMed

Leite, Gustavo B; Abdelaziz, Ahmed E M; Hallenbeck, Patrick C

2013-10-01

Biodiesel production using microalgae is attractive in a number of respects. Here a number of pros and cons to using microalgae for biofuels production are reviewed. Algal cultivation can be carried out using non-arable land and non-potable water with simple nutrient supply. In addition, algal biomass productivities are much higher than those of vascular plants and the extractable content of lipids that can be usefully converted to biodiesel, triacylglycerols (TAGs) can be much higher than that of the oil seeds now used for first generation biodiesel. On the other hand, practical, cost-effective production of biofuels from microalgae requires that a number of obstacles be overcome. These include the development of low-cost, effective growth systems, efficient and energy saving harvesting techniques, and methods for oil extraction and conversion that are environmentally benign and cost-effective. Promising recent advances in these areas are highlighted. Copyright © 2013 Elsevier Ltd. All rights reserved.

Geoengineering, marine microalgae, and climate stabilization in the 21st century

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greene, Charles H.; Huntley, Mark E.; Archibald, Ian

Society has set ambitious targets for stabilizing mean global temperature. To attain these targets, it will have to reduce CO 2 emissions to near zero by mid-century and subsequently remove CO 2 from the atmosphere during the latter half of the century. There is a recognized need to develop technologies for CO 2 removal; however, attempts to develop direct air-capture systems have faced both energetic and financial constraints. Recently, BioEnergy with Carbon Capture and Storage (BECCS) has emerged as a leading candidate for removing CO 2 from the atmosphere. But, BECCS can have negative consequences on land, nutrient, and watermore » use as well as biodiversity and food production. Here, we describe an alternative approach based on the large-scale industrial production of marine microalgae. When cultivated with proper attention to power, carbon, and nutrient sources, microalgae can be processed to produce a variety of biopetroleum products, including carbon-neutral biofuels for the transportation sector and long-lived, potentially carbon-negative construction materials for the built environment. In addition to these direct roles in mitigating and potentially reversing the effects of fossil CO 2 emissions, microalgae can also play an important indirect role. Furthermore, as microalgae exhibit much higher primary production rates than terrestrial plants, they require much less land area to produce an equivalent amount of bioenergy and/or food. On a global scale, the avoided emissions resulting from displacement of conventional agriculture may exceed the benefits of microalgae biofuels in achieving the climate stabilization goals.« less

Geoengineering, marine microalgae, and climate stabilization in the 21st century

DOE PAGES

Greene, Charles H.; Huntley, Mark E.; Archibald, Ian; ...

2017-03-21

Society has set ambitious targets for stabilizing mean global temperature. To attain these targets, it will have to reduce CO 2 emissions to near zero by mid-century and subsequently remove CO 2 from the atmosphere during the latter half of the century. There is a recognized need to develop technologies for CO 2 removal; however, attempts to develop direct air-capture systems have faced both energetic and financial constraints. Recently, BioEnergy with Carbon Capture and Storage (BECCS) has emerged as a leading candidate for removing CO 2 from the atmosphere. But, BECCS can have negative consequences on land, nutrient, and watermore » use as well as biodiversity and food production. Here, we describe an alternative approach based on the large-scale industrial production of marine microalgae. When cultivated with proper attention to power, carbon, and nutrient sources, microalgae can be processed to produce a variety of biopetroleum products, including carbon-neutral biofuels for the transportation sector and long-lived, potentially carbon-negative construction materials for the built environment. In addition to these direct roles in mitigating and potentially reversing the effects of fossil CO 2 emissions, microalgae can also play an important indirect role. Furthermore, as microalgae exhibit much higher primary production rates than terrestrial plants, they require much less land area to produce an equivalent amount of bioenergy and/or food. On a global scale, the avoided emissions resulting from displacement of conventional agriculture may exceed the benefits of microalgae biofuels in achieving the climate stabilization goals.« less

Production of biodiesel from microalgae through biological carbon capture: a review.

PubMed

Mondal, Madhumanti; Goswami, Shrayanti; Ghosh, Ashmita; Oinam, Gunapati; Tiwari, O N; Das, Papita; Gayen, K; Mandal, M K; Halder, G N

2017-06-01

Gradual increase in concentration of carbon dioxide (CO 2 ) in the atmosphere due to the various anthropogenic interventions leading to significant alteration in the global carbon cycle has been a subject of worldwide attention and matter of potential research over the last few decades. In these alarming scenario microalgae seems to be an attractive medium for capturing the excess CO 2 present in the atmosphere generated from different sources such as power plants, automobiles, volcanic eruption, decomposition of organic matters and forest fires. This captured CO 2 through microalgae could be used as potential carbon source to produce lipids for the generation of biofuel for replacing petroleum-derived transport fuel without affecting the supply of food and crops. This comprehensive review strives to provide a systematic account of recent developments in the field of biological carbon capture through microalgae for its utilization towards the generation of biodiesel highlighting the significance of certain key parameters such as selection of efficient strain, microalgal metabolism, cultivation systems (open and closed) and biomass production along with the national and international biodiesel specifications and properties. The potential use of photobioreactors for biodiesel production under the influence of various factors viz., light intensity, pH, time, temperature, CO 2 concentration and flow rate has been discussed. The review also provides an economic overview and future outlook on biodiesel production from microalgae.

Green genes: bioinformatics and systems-biology innovations drive algal biotechnology.

PubMed

Reijnders, Maarten J M F; van Heck, Ruben G A; Lam, Carolyn M C; Scaife, Mark A; dos Santos, Vitor A P Martins; Smith, Alison G; Schaap, Peter J

2014-12-01

Many species of microalgae produce hydrocarbons, polysaccharides, and other valuable products in significant amounts. However, large-scale production of algal products is not yet competitive against non-renewable alternatives from fossil fuel. Metabolic engineering approaches will help to improve productivity, but the exact metabolic pathways and the identities of the majority of the genes involved remain unknown. Recent advances in bioinformatics and systems-biology modeling coupled with increasing numbers of algal genome-sequencing projects are providing the means to address this. A multidisciplinary integration of methods will provide synergy for a systems-level understanding of microalgae, and thereby accelerate the improvement of industrially valuable strains. In this review we highlight recent advances and challenges to microalgal research and discuss future potential. Copyright © 2014 Elsevier Ltd. All rights reserved.

Flotation: A promising microalgae harvesting and dewatering technology for biofuels production.

PubMed

Ndikubwimana, Theoneste; Chang, Jingyu; Xiao, Zongyuan; Shao, Wenyao; Zeng, Xianhai; Ng, I-Son; Lu, Yinghua

2016-03-01

Microalgal biomass as renewable energy source is believed to be of great potential for reliable and sustainable biofuels production. However, microalgal biomass production is pinned by harvesting and dewatering stage thus hindering the developing and growing microalgae biotechnology industries. Flotation technology applied in mineral industry could be potentially applied in microalgae harvesting and dewatering, however substantial knowledge on different flotation units is essential. This paper presents an overview on different flotation units as promising cost-effective technologies for microalgae harvesting thus bestowing for further research in development and commercialization of microalgae based biofuels. Dispersed air flotation was found to be less energy consuming. Moreover, Jameson cell flotation and dispersed ozone flotation are believed to be energy efficient microalgae flotation approaches. Microalgae harvesting and dewatering by flotation is still at embryonic stage, therefore extended studies with the focus on life cycle assessment, sustainability of the flotation unit, optimization of the operating parameters using different algal species is imperative. Though there are a number of challenges in microalgae harvesting and dewatering, with well designed and developed cultivation, harvesting/dewatering, extraction and conversion technologies, progressively, microalgae technology will be of great potential for biological carbon sequestration, biofuels and biochemicals production. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Application of agar liquid-gel transition in cultivation and harvesting of microalgae for biodiesel production.

PubMed

Kumar, Vinod; Nanda, Manisha; Verma, Monu

2017-11-01

In order to increase microalgal biomass productivity efficient cultivation and harvesting methods are needed against the available traditional methods. The present study focuses on the same by harvesting microalgae using agar gel. Agar medium containing bold's basal medium (BBM) undergoes a thermoreversible gel transition. As compared to the traditional protocols, this gel is used to cultivate microalgae without even affecting the total productivity. To develop the gel for microalgae cultivation, agar was boiled in BBM. Then the agar was cooled to 35°C and microalgae culture was added to it. After seeding the microalgae the temperature of the agar was further decreased by 10°C to induce gelation. Instead of isolated cells microalgae were grown in clusters within the agar gel. Microalgal clusters gravimetrically settle at the bottom within 2h. In this method agar can be reused. Copyright © 2017 Elsevier Ltd. All rights reserved.

Allelopathy as a potential strategy to improve microalgae cultivation.

PubMed

Bacellar Mendes, Leonardo Brantes; Vermelho, Alane Beatriz

2013-10-21

One of the main obstacles for continuous productivity in microalgae cultivation is the presence of biological contaminants capable of eliminating large numbers of cells in a matter of days or even hours. However, a number of strategies are being used to combat and prevent contamination in microalgae cultivation. These strategies include the use of extreme conditions in the culture media such as high salinity and high pH to create an unfavorable environment for the competitive organisms or predators of the microalgae. Numerous studies have explored the potential of naturally occurring bioactive secondary metabolites, which are natural products from plants and microorganisms, as a source of such compounds. Some of these compounds are herbicides, and marine and freshwater microalgae are a source of these compounds. Microalgae produce a remarkable diversity of biologically active metabolites. Results based on the allelopathic potential of algae have only been described for laboratory-scale production and not for algae cultivation on a pilot scale. The adoption of allelopathy on microalgal strains is an unexplored field and may be a novel solution to improve algae production. Here we present information showing the diversity of allelochemicals from microalgae and the use of an allelopathic approach to control microalgae cultivation on a pilot scale based on R&D activities being carried out in Brazil for biodiesel production.

Allelopathy as a potential strategy to improve microalgae cultivation

PubMed Central

2013-01-01

One of the main obstacles for continuous productivity in microalgae cultivation is the presence of biological contaminants capable of eliminating large numbers of cells in a matter of days or even hours. However, a number of strategies are being used to combat and prevent contamination in microalgae cultivation. These strategies include the use of extreme conditions in the culture media such as high salinity and high pH to create an unfavorable environment for the competitive organisms or predators of the microalgae. Numerous studies have explored the potential of naturally occurring bioactive secondary metabolites, which are natural products from plants and microorganisms, as a source of such compounds. Some of these compounds are herbicides, and marine and freshwater microalgae are a source of these compounds. Microalgae produce a remarkable diversity of biologically active metabolites. Results based on the allelopathic potential of algae have only been described for laboratory-scale production and not for algae cultivation on a pilot scale. The adoption of allelopathy on microalgal strains is an unexplored field and may be a novel solution to improve algae production. Here we present information showing the diversity of allelochemicals from microalgae and the use of an allelopathic approach to control microalgae cultivation on a pilot scale based on R&D activities being carried out in Brazil for biodiesel production. PMID:24499580

Visual Simulation of Microalgae Growth in Bioregenerative Life Support System

NASA Astrophysics Data System (ADS)

Zhao, Ming

Bioregenerative life support system is one of the key technologies for future human deep space exploration and long-term space missions. BLSS use biological system as its core unit in combination with other physical and chemical equipments, under the proper control and manipulation by crew to complete a specific task to support life. Food production, waste treatment, oxygen and water regeneration are all conducted by higher plants or microalgae in BLSS, which is the most import characteristic different from other kinds of life support systems. Microalgae is light autotrophic micro-organisms, light undoubtedly is the most import factor which limits its growth and reproduction. Increasing or decreasing the light intensity changes the growth rate of microalgae, and then regulates the concentration of oxygen and carbon dioxide in the system. In this paper, based on the mathematical model of microalgae which grew under the different light intensity, three-dimensional visualization model was built and realized through using 3ds max, Virtools and some other three dimensional software, in order to display its change and impacting on oxygen and carbon dioxide intuitively. We changed its model structure and parameters, such as establishing closed-loop control system, light intensity, temperature and Nutrient fluid’s velocity and so on, carried out computer virtual simulation, and observed dynamic change of system with the aim of providing visualization support for system research.

Quorum sensing molecules in activated sludge could trigger microalgae lipid synthesis.

PubMed

Zhang, Chaofan; Li, Qingcheng; Fu, Liang; Zhou, Dandan; Crittenden, John C

2018-05-18

Cultivating microalgae using wastewater is an economical strategy to produce biofuel; however, microbial contamination has to be controlled strictly. Microalgae lipid accumulation can be triggered by environmental pressures, and here, we studied whether microbial contamination is the pressure for microalgae. We hypothesized this pressure was forced via cell-to-cell communication with quorum sensing molecules (QSMs). In this work, we verified the impacts of QSMs produced by activated sludge (wastewater-born microbial consortiums) on both lipid content and biomass production of the microalgae Chlorophyta sp., since in combination, they determined lipid productivity. With QSMs stress, the lipid content of Chlorophyta sp. increased by ∼84%, while biomass production decreased only slightly. Consistently, enzymes on the fatty acid synthesis pathways were generally up-regulated, while they were slightly down-regulated for DNA replication. In summary, the total lipid production improved by 86%. These results revealed the positive effects of microbial contamination on microalgae biofuel production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Integration of Waste Valorization for Sustainable Production of Chemicals and Materials via Algal Cultivation.

PubMed

Chen, Yong; Sun, Li-Ping; Liu, Zhi-Hui; Martin, Greg; Sun, Zheng

2017-11-27

Managing waste is an increasing problem globally. Microalgae have the potential to help remove contaminants from a range of waste streams and convert them into useful biomass. This article presents a critical review of recent technological developments in the production of chemicals and other materials from microalgae grown using different types of waste. A range of novel approaches are examined for efficiently capturing CO 2 in flue gas via photosynthetic microalgal cultivation. Strategies for using microalgae to assimilate nitrogen, organic carbon, phosphorus, and metal ions from wastewater are considered in relation to modes of production. Generally, more economical open cultivation systems such as raceway ponds are better suited for waste conversion than more expensive closed photobioreactor systems, which might have use for higher-value products. The effect of cultivation methods and the properties of the waste streams on the composition the microalgal biomass is discussed relative to its utilization. Possibilities include the production of biodiesel via lipid extraction, biocrude from hydrothermal liquefaction, and bioethanol or biogas from microbial conversion. Microalgal biomass produced from wastes may also find use in higher-value applications including protein feeds or for the production of bioactive compounds such as astaxanthin or omega-3 fatty acids. However, for some waste streams, further consideration of how to manage potential microbial and chemical contaminants is needed for food or health applications. The use of microalgae for waste valorization holds promise. Widespread implementation of the available technologies will likely follow from further improvements to reduce costs, as well as the increasing pressure to effectively manage waste.

Modeling the competition between antenna size mutant and wild type microalgae in outdoor mass culture.

PubMed

de Mooij, Tim; Schediwy, Kira; Wijffels, René H; Janssen, Marcel

2016-12-20

Under high light conditions, microalgae are oversaturated with light which significantly reduces the light use efficiency. Microalgae with a reduced pigment content, antenna size mutants, have been proposed as a potential solution to increase the light use efficiency. The goal of this study was to investigate the competition between antenna size mutants and wild type microalgae in mass cultures. Using a kinetic model and literature-derived experimental data from wild type Chlorella sorokiniana, the productivity and competition of wild type cells and antenna size mutants were simulated. Cultivation was simulated in an outdoor microalgal raceway pond production system which was assumed to be limited by light only. Light conditions were based on a Mediterranean location (Tunisia) and a more temperate location (the Netherlands). Several wild type contamination levels were simulated in each mutant culture separately to predict the effect on the productivity over the cultivation time of a hypothetical summer season of 100days. The simulations demonstrate a good potential of antenna size reduction to increase the biomass productivity of microalgal cultures. However, it was also found that after a contamination with wild type cells the mutant cultures will be rapidly overgrown resulting in productivity loss. Copyright © 2016 Elsevier B.V. All rights reserved.

Microalgae as source of biofuel: technology and prospective

NASA Astrophysics Data System (ADS)

Ferraro, Angelo

2017-12-01

Microalgae are autotrophic organisms found in solitary cells or in groups of single cells connected together. Their natural environment are typically freshwater and marine systems. Microalgae produce, via photosynthesis, approximately one-half of oxygen generated on earth while simultaneously consume carbon dioxide (CO2). Among the technologies being examined to produce green fuels (e.g. biodiesel, bioethanol and syngas), microalgae are viewed by many in the scientific community as having the greatest potential to become economically viable fuels. Nevertheless, to reach economic parity with fossil fuels there are still several challenges to be tackle. These include improving harvesting and oil extraction processes as well as increasing biomass productivity and oil content. All of these challenges can be impacted by genetic, molecular, and ultimately synthetic biology techniques.

The role of silica nanoparticles on long-term room-temperature stabilization of water-in-oil emulsions containing microalgae.

PubMed

Fernández, L; Scher, H; VanderGheynst, J S

2015-12-01

Prior research has demonstrated that microalgae can be stored for extended periods of time at room temperature in water-in-oil (W/O) emulsions stabilized by surface modified silica nanoparticles. However, little research has been done to examine the impact of nanoparticle concentration on emulsion stability. Such information is important for large-scale production of emulsions for microalgae storage and delivery. Studies were done to examine the impact of silica nanoparticle concentration on emulsion stability and identify the lower limit for nanoparticle concentration. Emulsion physical stability was determined using internal phase droplet size measurements and biological stability was evaluated using cell density measurements. The results demonstrate that nanoparticle concentrations as low as 0·5wt% in the oil phase can be used without significant losses in emulsion stability and microalgae viability. Stabilization technologies are needed for long-term storage and application of microalgae in agricultural-scale systems. While prior work has demonstrated that water-in-oil emulsions containing silica nanoparticles offer a promising solution for long-term microalgae storage at room temperature, little research has been done to examine the impact of nanoparticle concentration on emulsion stability. Here, we show the effects of silica nanoparticle concentration on maintaining physical stability of emulsions and sustaining viable cells. The results enable informed decisions to be made regarding production of emulsions containing silica nanoparticles and associated impacts on stabilization of microalgae. © 2015 The Society for Applied Microbiology.

Current progress and future prospect of microalgal biomass harvest using various flocculation technologies.

PubMed

Wan, Chun; Alam, Md Asraful; Zhao, Xin-Qing; Zhang, Xiao-Yue; Guo, Suo-Lian; Ho, Shih-Hsin; Chang, Jo-Shu; Bai, Feng-Wu

2015-05-01

Microalgae have been extensively studied for the production of various valuable products. Application of microalgae for the production of renewable energy has also received increasing attention in recent years. However, high cost of microalgal biomass harvesting is one of the bottlenecks for commercialization of microalgae-based industrial processes. Considering harvesting efficiency, operation economics and technological feasibility, flocculation is a superior method to harvest microalgae from mass culture. In this article, the latest progress of various microalgal cell harvesting methods via flocculation is reviewed with the emphasis on the current progress and prospect in environmentally friendly bio-based flocculation. Harvesting microalgae through bio-based flocculation is a promising component of the low-cost microalgal biomass production technology. Copyright © 2014 Elsevier Ltd. All rights reserved.

Screening microalgae isolated from urban storm- and wastewater systems as feedstock for biofuel.

PubMed

Massimi, Rebecca; Kirkwood, Andrea E

2016-01-01

Exploiting microalgae as feedstock for biofuel production is a growing field of research and application, but there remain challenges related to industrial viability and economic sustainability. A solution to the water requirements of industrial-scale production is the use of wastewater as a growth medium. Considering the variable quality and contaminant loads of wastewater, algal feedstock would need to have broad tolerance and resilience to fluctuating wastewater conditions during growth. As a first step in targeting strains for growth in wastewater, our study isolated microalgae from wastewater habitats, including urban stormwater-ponds and a municipal wastewater-treatment system, to assess growth, fatty acids and metal tolerance under standardized conditions. Stormwater ponds in particular have widely fluctuating conditions and metal loads, so microalgae from this type of environment may have desirable traits for growth in wastewater. Forty-three algal strains were isolated in total, including several strains from natural habitats. All strains, with the exception of one cyanobacterial strain, are members of the Chlorophyta, including several taxa commonly targeted for biofuel production. Isolates were identified using taxonomic and 18S rRNA sequence methods, and the fastest growing strains with ideal fatty acid profiles for biodiesel production included Scenedesmus and Desmodesmus species (Growth rate (d(-1)) > 1). All isolates in a small, but diverse taxonomic group of test-strains were tolerant of copper at wastewater-relevant concentrations. Overall, more than half of the isolated strains, particularly those from stormwater ponds, show promise as candidates for biofuel feedstock.

An outdoor test facility for the large-scale production of microalgae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, D.A.; Weissman, J.; Goebel, R.

The goal of the US Department of EnergySolar Energy Research Institute's Aquatic Species Program is to develop the technology base to produce liquid fuels from microalgae. This technology is being initially developed for the desert Southwest. As part of this program an outdoor test facility has been designed and constructed in Roswell, New Mexico. The site has a large existing infrastructure, a suitable climate, and abundant saline groundwater. This facility will be used to evaluate productivity of microalgae strains and conduct large-scale experiments to increase biomass productivity while decreasing production costs. Six 3-m/sup 2/ fiberglass raceways were constructed. Several microalgaemore » strains were screened for growth, one of which had a short-term productivity rate of greater than 50 g dry wt m/sup /minus/2/ d/sup /minus/1/. Two large-scale, 0.1-ha raceways have also been built. These are being used to evaluate the performance trade-offs between low-cost earthen liners and higher cost plastic liners. A series of hydraulic measurements is also being carried out to evaluate future improved pond designs. Future plans include a 0.5-ha pond, which will be built in approximately 2 years to test a scaled-up system. This unique facility will be available to other researchers and industry for studies on microalgae productivity. 6 refs., 9 figs., 1 tab.« less

Catalytic deoxygenation of microalgae oil to green hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Chen; Bruck, Thomas; Lercher, Johannes A.

2013-05-14

Microalgae are high potential raw biomass material for triglyceride feedstock, due to their high oil content and rapid growth rate, and because algae cultivation does not compete with edible food on arable land. This review addresses first the microalgae cultivation with an overview of the productivity and growth of microalgae, the recovery of lipids from the microalgae, and chemical compositions of microalgae biomass and microalgal oil. Second, three basic approaches are discussed to downstream processing for the production of green gasoline and diesel hydrocarbons from microalgae oil, including cracking with zeolite, hydrotreating with supported sulfided catalysts and hydrodeoxygenation with non-sulfidemore » metal catalysts. For the triglyceride derived bio-fuels, only “drop-in” gasoline and diesel range components are discussed in this review.« less

Advances in Microalgae-Derived Phytosterols for Functional Food and Pharmaceutical Applications

PubMed Central

Luo, Xuan; Su, Peng; Zhang, Wei

2015-01-01

Microalgae contain a variety of bioactive lipids with potential applications in aquaculture feed, biofuel, food and pharmaceutical industries. While microalgae-derived polyunsaturated fatty acid (PUFA) and their roles in promoting human health have been extensively studied, other lipid types from this resource, such as phytosterols, have been poorly explored. Phytosterols have been used as additives in many food products such as spread, dairy products and salad dressing. This review focuses on the recent advances in microalgae-derived phytosterols with functional bioactivities and their potential applications in functional food and pharmaceutical industries. It highlights the importance of microalgae-derived lipids other than PUFA for the development of an advanced microalgae industry. PMID:26184233

Advances in Microalgae-Derived Phytosterols for Functional Food and Pharmaceutical Applications.

PubMed

Luo, Xuan; Su, Peng; Zhang, Wei

2015-07-09

Microalgae contain a variety of bioactive lipids with potential applications in aquaculture feed, biofuel, food and pharmaceutical industries. While microalgae-derived polyunsaturated fatty acid (PUFA) and their roles in promoting human health have been extensively studied, other lipid types from this resource, such as phytosterols, have been poorly explored. Phytosterols have been used as additives in many food products such as spread, dairy products and salad dressing. This review focuses on the recent advances in microalgae-derived phytosterols with functional bioactivities and their potential applications in functional food and pharmaceutical industries. It highlights the importance of microalgae-derived lipids other than PUFA for the development of an advanced microalgae industry.

The role of microalgae as biodiesel feedstock in a tropical setting: Economics, agro-energy competitiveness, and potential impacts on regional agricultural feedstock production

NASA Astrophysics Data System (ADS)

Boll, Matias G.

The objective of this study is to obtain a realistic evaluation of the potential role of microalgae as a biodiesel feedstock in a tropical setting. First, microalgae economics are estimated, including the detailed design of a 400 ha microalgae open pond production farm together with the microalgae biomass and crude oil production costs calculations. Sensitivity analysis and a stochastic evaluation of the microalgae venture chances for profit are also included. Next, microalgae potential for biodiesel production is compared to traditional oil crops such as soybeans and African palm. This comparison is performed using the Northeast Region (NER) of Brazil as background. Six potential biodiesel feedstock sources produced in the NER and microalgae are compared considering selected environmental, economic and social sustainability indicators. Finally, in the third chapter, the study proposes a cropland allocation model for the NER. The model aims to offer insights to the decision maker concerning biofuel development strategies and their impact on regional agricultural feedstock production. In the model, cropland allocation among three agriculture feedstock sectors, namely staple food, commodity export and biofuel is optimized through the use of the multiple objective technique referred to as compromise programming (CP). Our results indicate a projected microalgae total production cost of R 78,359 ha-1 (US43,533), which has a breakdown as follows: R 34,133 ha-1 (US18,963) for operating costs and R 44,226 ha-1 (US24,570) for overhead (ownership) costs. Our stochastic analysis indicates that microalgae production under the conditions assumed in the baseline scenario of this study has a 0% chance to present a positive NPV for a microalgae crude oil price of R 1.86. This price corresponds to an international oil price around US 77 bbl-1. To obtain a reasonable investment return (IRR = 12%) from the microalgae farm, an international oil price as high as US 461 bbl-1 is required. Despite the advantage of using about 14 times less cropland area (0.13 ha boe-1 ), microalgae presented significant disadvantages as compared to some of the traditional oil crops. Among these is the significant amount of N fertilizer and water demanded by microalgae production, namely 205 kg and 4,990 boe -1, about 132% and 30% higher than the second highest value among the crops compared in this study, respectively. Optimized CP scenarios expanded annual cropland allocation to 14.58 million ha in the NER, year 2017, compared to 11.04 and 12.81 million ha in current (2007) and baseline (2017) scenarios, respectively. In comparison to the baseline scenario, cropland expansions allied to the shift of the commodities export dedicated cropland to the biofuel production sector in CP scenarios significantly increased the NER fuel autonomy (95%) and reduced its R 5,126 million reais deficit baseline comprehensive feedstock trade balance by 79%. Contrary to the concerns usually referred to biofuel development, our model indicates that in the NER case, it is the commodity export, rather than the staple food agriculture feedstock production sector, that is mostly affected by the biofuel cropland allocation demand. When compared to traditional oil crops, microalgae-based biodiesel scenarios could not significantly improve regional staple food autonomy, increasing this objective by 1% only. The NER fuel autonomy, in its turn, is positively impacted in the microalgae scenarios, but the increment as compared to the traditional oil crops is rather small, namely 2% and 7% in the B5 and B10 levels, respectively. These results indicate that the potential advantages expected for the microalgae-based biodiesel introduction did not materialize for the NER. It is concluded that the adoption of microalgae-based biodiesel is not an interesting biofuel alternative for the NER of Brazil for the next ten years.

Modifications of the metabolic pathways of lipid and triacylglycerol production in microalgae

PubMed Central

2011-01-01

Microalgae have presented themselves as a strong candidate to replace diminishing oil reserves as a source of lipids for biofuels. Here we describe successful modifications of terrestrial plant lipid content which increase overall lipid production or shift the balance of lipid production towards lipid varieties more useful for biofuel production. Our discussion ranges from the biosynthetic pathways and rate limiting steps of triacylglycerol formation to enzymes required for the formation of triacylglycerol containing exotic lipids. Secondarily, we discuss techniques for genetic engineering and modification of various microalgae which can be combined with insights gained from research in higher plants to aid in the creation of production strains of microalgae. PMID:22047615

Lifecycle assessment of microalgae to biofuel: Comparison of thermochemical processing pathways

DOE PAGES

Bennion, Edward P.; Ginosar, Daniel M.; Moses, John; ...

2015-01-16

Microalgae are currently being investigated as a renewable transportation fuel feedstock based on various advantages that include high annual yields, utilization of poor quality land, does not compete with food, and can be integrated with various waste streams. This study focuses on directly assessing the impact of two different thermochemical conversion technologies on the microalgae to biofuel process through life cycle assessment. A system boundary of a “well to pump” (WTP) is defined and includes sub-process models of the growth, dewatering, thermochemical bio-oil recovery, bio-oil stabilization, conversion to renewable diesel, and transport to the pump. Models were validated with experimentalmore » and literature data and are representative of an industrial-scale microalgae to biofuel process. Two different thermochemical bio-oil conversion systems are modeled and compared on a systems level, hydrothermal liquefaction (HTL) and pyrolysis. The environmental impact of the two pathways were quantified on the metrics of net energy ratio (NER), defined here as energy consumed over energy produced, and greenhouse gas (GHG) emissions. Results for WTP biofuel production through the HTL pathway were determined to be 1.23 for the NER and GHG emissions of -11.4 g CO 2-eq (MJ renewable diesel) -1. WTP biofuel production through the pyrolysis pathway results in a NER of 2.27 and GHG emissions of 210 g CO2 eq (MJ renewable diesel)-1. The large environmental impact associated with the pyrolysis pathway is attributed to feedstock drying requirements and combustion of co-products to improve system energetics. Discussion focuses on a detailed breakdown of the overall process energetics and GHGs, impact of modeling at laboratory- scale compared to industrial-scale, environmental impact sensitivity to engineering systems input parameters for future focused research and development and a comparison of results to literature.« less

Life cycle assessment of microalgae to biofuel: Thermochemical processing through hydrothermal liquefaction or pyrolysis

NASA Astrophysics Data System (ADS)

Bennion, Edward P.

Microalgae are currently being investigated as a renewable transportation fuel feedstock based on various advantages that include high annual yields, utilization of poor quality land, does not compete with food, and can be integrated with various waste streams. This study focuses on directly assessing the impact of two different thermochemical conversion technologies on the microalgae-to-biofuel process through life cycle assessment. A system boundary of a "well to pump" (WTP) is defined and includes sub-process models of the growth, dewatering, thermochemical bio-oil recovery, bio-oil stabilization, conversion to renewable diesel, and transport to the pump. Models were validated with experimental and literature data and are representative of an industrial-scale microalgae-to-biofuel process. Two different thermochemical bio-oil conversion systems are modeled and compared on a systems level, hydrothermal liquefaction (HTL) and pyrolysis. The environmental impact of the two pathways were quantified on the metrics of net energy ratio (NER), defined here as energy consumed over energy produced, and greenhouse gas (GHG) emissions. Results for WTP biofuel production through the HTL pathway were determined to be 1.23 for the NER and GHG emissions of -11.4 g CO2 eq (MJ renewable diesel)-1. WTP biofuel production through the pyrolysis pathway results in a NER of 2.27 and GHG emissions of 210 g CO2 eq (MJ renewable diesel)-1. The large environmental impact associated with the pyrolysis pathway is attributed to feedstock drying requirements and combustion of co-products to improve system energetics. Discussion focuses on a detailed breakdown of the overall process energetics and GHGs, impact of modeling at laboratory-scale compared to industrial-scale, environmental impact sensitivity to engineering systems input parameters for future focused research and development, and a comparison of results to literature.

Effect of Metals, Metalloids and Metallic Nanoparticles on Microalgae Growth and Industrial Product Biosynthesis: A Review

PubMed Central

Miazek, Krystian; Iwanek, Waldemar; Remacle, Claire; Richel, Aurore; Goffin, Dorothee

2015-01-01

Microalgae are a source of numerous compounds that can be used in many branches of industry. Synthesis of such compounds in microalgal cells can be amplified under stress conditions. Exposure to various metals can be one of methods applied to induce cell stress and synthesis of target products in microalgae cultures. In this review, the potential of producing diverse biocompounds (pigments, lipids, exopolymers, peptides, phytohormones, arsenoorganics, nanoparticles) from microalgae cultures upon exposure to various metals, is evaluated. Additionally, different methods to alter microalgae response towards metals and metal stress are described. Finally, possibilities to sustain high growth rates and productivity of microalgal cultures in the presence of metals are discussed. PMID:26473834

Concurrent extraction and reaction for the production of biodiesel from wet microalgae.

PubMed

Im, Hanjin; Lee, HanSol; Park, Min S; Yang, Ji-Won; Lee, Jae W

2014-01-01

This work addresses a reliable in situ transesterification process which integrates lipid extraction from wet microalgae, and its conversion to biodiesel, with a yield higher than 90 wt.%. This process enables single-step production of biodiesel from microalgae by mixing wet microalgal cells with solvent, methanol, and acid catalyst; and then heating them in one pot. The effects of reaction parameters such as reaction temperature, wet cell weight, reaction time, and catalyst volume on the conversion yield are investigated. This simultaneous extraction and transesterification of wet microalgae may enable a significant reduction in energy consumption by eliminating the drying process of algal cells and realize the economic production of biodiesel using wet microalgae. Copyright © 2013 Elsevier Ltd. All rights reserved.

Developments and challenges in biodiesel production from microalgae: A review.

PubMed

Taparia, Tanvi; Mvss, Manjari; Mehrotra, Rajesh; Shukla, Paritosh; Mehrotra, Sandhya

2016-09-01

The imminent depletion of fossil fuels and the surging global demand for renewable energy have led to the search for nonconventional energy sources. After a few decades of trial and error, the world is now testing the sources of the third generation of fossil fuels, which contain for most parts microalgae. With more than 80% oil content, being adaptable in growth parameters and highly versatile, microalgae are highly promising sources of biofuels in the present time. The present article makes a sweeping attempt to highlight the various methods employed for cultivation of microalgae, techniques to harvest and extract biomass from huge algal cultures, as well as their downstream production and processing procedures. The advantages, limitations, and challenges faced by each of them have been described to some extent. Major concerns pertaining to biofuels are supposed to be their environmental sustainability and economic viability along with their cost effectiveness. This would require a great deal of empirical data on existing systems and a great deal of optimization to generate a more robust one. We have concluded our article with a SWOT analysis of using algae for biodiesel production in a tabulated form. © 2015 International Union of Biochemistry and Molecular Biology, Inc.

Multi-Product Microalgae Biorefineries: From Concept Towards Reality.

PubMed

't Lam, G P; Vermuë, M H; Eppink, M H M; Wijffels, R H; van den Berg, C

2018-02-01

Although microalgae are a promising biobased feedstock, industrial scale production is still far off. To enhance the economic viability of large-scale microalgae processes, all biomass components need to be valorized, requiring a multi-product biorefinery. However, this concept is still too expensive. Typically, downstream processing of industrial biotechnological bulk products accounts for 20-40% of the total production costs, while for a microalgae multi-product biorefinery the costs are substantially higher (50-60%). These costs are high due to the lack of appropriate and mild technologies to access the different product fractions such as proteins, carbohydrates, and lipids. To reduce the costs, simplified processes need to be developed for the main unit operations including harvesting, cell disruption, extraction, and possibly fractionation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biodiesel production with microalgae as feedstock: from strains to biodiesel.

PubMed

Gong, Yangmin; Jiang, Mulan

2011-07-01

Due to negative environmental influence and limited availability, petroleum-derived fuels need to be replaced by renewable biofuels. Biodiesel has attracted intensive attention as an important biofuel. Microalgae have numerous advantages for biodiesel production over many terrestrial plants. There are a series of consecutive processes for biodiesel production with microalgae as feedstock, including selection of adequate microalgal strains, mass culture, cell harvesting, oil extraction and transesterification. To reduce the overall production cost, technology development and process optimization are necessary. Genetic engineering also plays an important role in manipulating lipid biosynthesis in microalgae. Many approaches, such as sequestering carbon dioxide from industrial plants for the carbon source, using wastewater for the nutrient supply, and maximizing the values of by-products, have shown a potential for cost reduction. This review provides a brief overview of the process of biodiesel production with microalgae as feedstock. The methods associated with this process (e.g. lipid determination, mass culture, oil extraction) are also compared and discussed.

Continuous cultivation of photosynthetic microorganisms: Approaches, applications and future trends.

PubMed

Fernandes, Bruno D; Mota, Andre; Teixeira, Jose A; Vicente, Antonio A

2015-11-01

The possibility of using photosynthetic microorganisms, such as cyanobacteria and microalgae, for converting light and carbon dioxide into valuable biochemical products has raised the need for new cost-efficient processes ensuring a constant product quality. Food, feed, biofuels, cosmetics and pharmaceutics are among the sectors that can profit from the application of photosynthetic microorganisms. Biomass growth in a photobioreactor is a complex process influenced by multiple parameters, such as photosynthetic light capture and attenuation, nutrient uptake, photobioreactor hydrodynamics and gas-liquid mass transfer. In order to optimize productivity while keeping a standard product quality, a permanent control of the main cultivation parameters is necessary, where the continuous cultivation has shown to be the best option. However it is of utmost importance to recognize the singularity of continuous cultivation of cyanobacteria and microalgae due to their dependence on light availability and intensity. In this sense, this review provides comprehensive information on recent breakthroughs and possible future trends regarding technological and process improvements in continuous cultivation systems of microalgae and cyanobacteria, that will directly affect cost-effectiveness and product quality standardization. An overview of the various applications, techniques and equipment (with special emphasis on photobioreactors) in continuous cultivation of microalgae and cyanobacteria are presented. Additionally, mathematical modeling, feasibility, economics as well as the applicability of continuous cultivation into large-scale operation, are discussed. Copyright © 2015 Elsevier Inc. All rights reserved.

Expression of the heterologous Dunaliella tertiolecta fatty acyl-ACP thioesterase leads to increased lipid production in Chlamydomonas reinhardtii.

PubMed

Tan, Kenneth Wei Min; Lee, Yuan Kun

2017-04-10

Biofuel production from genetically-engineered microalgae is currently among the most widely studied strategies in generating renewable energy. However, microalgae currently suffer from low oil yields which limit the commercial feasibility of industrial-scale production. A major bottleneck in cost-efficient biofuel production from microalgae is the dilemma between biomass productivity and lipid accumulation. When grown under stressful culture conditions such as nitrogen depletion, microalgae accumulate large amounts of neutral lipids, but it comes at the expense of growth which negatively impacts overall lipid productivity. Overexpression of acyl-ACP thioesterases (TE) had been successful in increasing the production of fatty acids (FA) in prokaryotes such as E. coli and cyanobacteria, but has not been effectively tested in microalgae. In this study, we introduced a TE from D. tertiolecta (DtTE) into C. reinhardtii to investigate its effects on FA production without compromising growth. The results indicate that C. reinhardtii transformants were able to produce 63 and 94% more neutral lipids than the wild-type, which translates to an approximately 56% improvement in total lipids, without compromising growth. These findings demonstrate the cross-species functionality of TE, and provide a platform for further studies into using TE as a strategy to increase biofuel production from microalgae. Copyright © 2017 Elsevier B.V. All rights reserved.

Life cycle analyses of CO2, energy, and cost for four different routes of microalgal bioenergy conversion.

PubMed

Ventura, Jey-R S; Yang, Benqin; Lee, Yong-Woo; Lee, Kisay; Jahng, Deokjin

2013-06-01

With a target production of 1000 ton of dry algae/yr, lipid content of 30 wt.%, and productivity of 30 g/m(2)-d in a 340-day annual operation, four common scenarios of microalgae bioenergy routes were assessed in terms of cost, energy, and CO2 inputs and outputs. Scenario 1 (biodiesel production), Scenario 2 (Scenario 1 with integrated anaerobic digestion system), Scenario 3 (biogas production), and Scenario 4 (supercritical gasification) were evaluated. Scenario 4 outperformed other scenarios in terms of net energy production (1282.42 kWh/ton algae) and CO2 removal (1.32 ton CO2/ton algae) while Scenario 2 surpassed the other three scenarios in terms of net cost. Scenario 1 produced the lowest energy while Scenario 3 was the most expensive bioenergy system. This study evaluated critical parameters that could direct the proper design of the microalgae bioenergy system with an efficient energy production, CO2 removal, and economic feasibility. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of light on the production of bioelectricity and added-value microalgae biomass in a Photosynthetic Alga Microbial Fuel Cell.

PubMed

Gouveia, Luísa; Neves, Carole; Sebastião, Diogo; Nobre, Beatriz P; Matos, Cristina T

2014-02-01

This study demonstrates the simultaneous production of bioelectricity and added-value pigments in a Photosynthetic Alga Microbial Fuel Cell (PAMFC). A PAMFC was operated using Chlorella vulgaris in the cathode compartment and a bacterial consortium in the anode. The system was studied at two different light intensities and the maximum power produced was 62.7 mW/m(2) with a light intensity of 96 μE/(m(2)s). The results showed that increasing light intensity from 26 to 96 μE/(m(2)s) leads to an increase of about 6-folds in the power produced. Additionally, the pigments produced by the microalga were analysed and the results showed that the light intensity and PAMFC operation potentiated the carotenogenesis in the cathode compartment. The demonstrated possibility of producing added-value microalgae biomass in microbial fuel cell cathodes will increase the economic feasibility of these bioelectrochemical systems, allowing the development of energy efficient systems for wastewater treatment and carbon fixation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Heterotrophic cultivation of microalgae for production of biodiesel.

PubMed

Mohamed, Mohd Shamzi; Wei, Lai Zee; Ariff, Arbakariya B

2011-08-01

High cell density cultivation of microalgae via heterotrophic growth mechanism could effectively address the issues of low productivity and operational constraints presently affecting the solar driven biodiesel production. This paper reviews the progress made so far in the development of commercial-scale heterotrophic microalgae cultivation processes. The review also discusses on patentable concepts and innovations disclosed in the past four years with regards to new approaches to microalgal cultivation technique, improvisation on the process flow designs to economically produced biodiesel and genetic manipulation to confer desirable traits leading to much valued high lipid-bearing microalgae strains.

Examination of Triacylglycerol Biosynthetic Pathways via De Novo Transcriptomic and Proteomic Analyses in an Unsequenced Microalga

PubMed Central

Guarnieri, Michael T.; Nag, Ambarish; Smolinski, Sharon L.; Darzins, Al; Seibert, Michael; Pienkos, Philip T.

2011-01-01

Biofuels derived from algal lipids represent an opportunity to dramatically impact the global energy demand for transportation fuels. Systems biology analyses of oleaginous algae could greatly accelerate the commercialization of algal-derived biofuels by elucidating the key components involved in lipid productivity and leading to the initiation of hypothesis-driven strain-improvement strategies. However, higher-level systems biology analyses, such as transcriptomics and proteomics, are highly dependent upon available genomic sequence data, and the lack of these data has hindered the pursuit of such analyses for many oleaginous microalgae. In order to examine the triacylglycerol biosynthetic pathway in the unsequenced oleaginous microalga, Chlorella vulgaris, we have established a strategy with which to bypass the necessity for genomic sequence information by using the transcriptome as a guide. Our results indicate an upregulation of both fatty acid and triacylglycerol biosynthetic machinery under oil-accumulating conditions, and demonstrate the utility of a de novo assembled transcriptome as a search model for proteomic analysis of an unsequenced microalga. PMID:22043295

Quantification of Heavy Metals and Other Inorganic Contaminants on the Productivity of Microalgae.

PubMed

Napan, Katerine; Hess, Derek; McNeil, Brian; Quinn, Jason C

2015-07-10

Increasing demand for renewable fuels has researchers investigating the feasibility of alternative feedstocks, such as microalgae. Inherent advantages include high potential yield, use of non-arable land and integration with waste streams. The nutrient requirements of a large-scale microalgae production system will require the coupling of cultivation systems with industrial waste resources, such as carbon dioxide from flue gas and nutrients from wastewater. Inorganic contaminants present in these wastes can potentially lead to bioaccumulation in microalgal biomass negatively impact productivity and limiting end use. This study focuses on the experimental evaluation of the impact and the fate of 14 inorganic contaminants (As, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Sb, Se, Sn, V and Zn) on Nannochloropsis salina growth. Microalgae were cultivated in photobioreactors illuminated at 984 µmol m(-2) sec(-1) and maintained at pH 7 in a growth media polluted with inorganic contaminants at levels expected based on the composition found in commercial coal flue gas systems. Contaminants present in the biomass and the medium at the end of a 7 day growth period were analytically quantified through cold vapor atomic absorption spectrometry for Hg and through inductively coupled plasma mass spectrometry for As, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sb, Se, Sn, V and Zn. Results show N. salina is a sensitive strain to the multi-metal environment with a statistical decrease in biomass yieldwith the introduction of these contaminants. The techniques presented here are adequate for quantifying algal growth and determining the fate of inorganic contaminants.

Quantification of Heavy Metals and Other Inorganic Contaminants on the Productivity of Microalgae

PubMed Central

Napan, Katerine; Hess, Derek; McNeil, Brian; Quinn, Jason C.

2015-01-01

Increasing demand for renewable fuels has researchers investigating the feasibility of alternative feedstocks, such as microalgae. Inherent advantages include high potential yield, use of non-arable land and integration with waste streams. The nutrient requirements of a large-scale microalgae production system will require the coupling of cultivation systems with industrial waste resources, such as carbon dioxide from flue gas and nutrients from wastewater. Inorganic contaminants present in these wastes can potentially lead to bioaccumulation in microalgal biomass negatively impact productivity and limiting end use. This study focuses on the experimental evaluation of the impact and the fate of 14 inorganic contaminants (As, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Sb, Se, Sn, V and Zn) on Nannochloropsis salina growth. Microalgae were cultivated in photobioreactors illuminated at 984 µmol m-2 sec-1 and maintained at pH 7 in a growth media polluted with inorganic contaminants at levels expected based on the composition found in commercial coal flue gas systems. Contaminants present in the biomass and the medium at the end of a 7 day growth period were analytically quantified through cold vapor atomic absorption spectrometry for Hg and through inductively coupled plasma mass spectrometry for As, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sb, Se, Sn, V and Zn. Results show N. salina is a sensitive strain to the multi-metal environment with a statistical decrease in biomass yieldwith the introduction of these contaminants. The techniques presented here are adequate for quantifying algal growth and determining the fate of inorganic contaminants. PMID:26274060

Evaluation of available saline water resources in New Mexico for the production of microalgae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lansford, R.; Hernandez, J.; Enis, P.

Researchers evaluated saline water resources in New Mexico for their suitability as sites for large-scale microalgae production facilities. Production of microalgae could provide a renewable source of fuel, chemicals, and food. In addition, making use of the unused saline water resources would increase the economic activity in the state. After analyzing the 15 billion acre-ft of unused saline water resources in the state, scientists narrowed the locations down to six sites with the most potential. With further analysis, they chose the Tularosa Basin in southern New Mexico as the best-suited area for 100-hectare microalgae production facility. 34 refs., 38 figs.,more » 14 tabs.« less

Isolation and Evaluation of Oil-Producing Microalgae from Subtropical Coastal and Brackish Waters

PubMed Central

Lim, David K. Y.; Garg, Sourabh; Timmins, Matthew; Zhang, Eugene S. B.; Thomas-Hall, Skye R.; Schuhmann, Holger; Li, Yan; Schenk, Peer M.

2012-01-01

Microalgae have been widely reported as a promising source of biofuels, mainly based on their high areal productivity of biomass and lipids as triacylglycerides and the possibility for cultivation on non-arable land. The isolation and selection of suitable strains that are robust and display high growth and lipid accumulation rates is an important prerequisite for their successful cultivation as a bioenergy source, a process that can be compared to the initial selection and domestication of agricultural crops. We developed standard protocols for the isolation and cultivation for a range of marine and brackish microalgae. By comparing growth rates and lipid productivity, we assessed the potential of subtropical coastal and brackish microalgae for the production of biodiesel and other oil-based bioproducts. This study identified Nannochloropsis sp., Dunaniella salina and new isolates of Chlorella sp. and Tetraselmis sp. as suitable candidates for a multiple-product algae crop. We conclude that subtropical coastal microalgae display a variety of fatty acid profiles that offer a wide scope for several oil-based bioproducts, including biodiesel and omega-3 fatty acids. A biorefinery approach for microalgae would make economical production more feasible but challenges remain for efficient harvesting and extraction processes for some species. PMID:22792403

A time-space model for the growth of microalgae biofilms for biofuel production.

PubMed

Polizzi, B; Bernard, O; Ribot, M

2017-11-07

We present in this paper a spatial model describing the growth of a photosynthetic microalgae biofilm. In this model we consider photosynthesis, extracellular matrix excretion, and mortality. These mechanisms are described precisely using kinetic laws that take into account some saturation effects which limit the reaction rates and involve different components that we treat individually. In particular, to obtain a more detailed description of the microalgae growth, we consider separately the lipids they contain and the functional part of microalgae (proteins, RNA, etc ...), the latter playing a leading role in photosynthesis. We also consider the components dissolved in liquid phase as CO 2 . The model is based on mixture theory and the behaviour of each component is described on the one hand by mass conservation, which takes into account biological features of the system, and on the other hand by conservation of momentum, which describes the physical properties of the components. Some numerical simulations are displayed in the one-dimensional case and show that the model is able to estimate accurately the biofilm productivity. Copyright © 2017 Elsevier Ltd. All rights reserved.

Current Techniques of Growing Algae Using Flue Gas from Exhaust Gas Industry: a Review.

PubMed

Huang, Guanhua; Chen, Feng; Kuang, Yali; He, Huan; Qin, An

2016-03-01

The soaring increase of flue gas emission had caused global warming, environmental pollution as well as climate change. Widespread concern on reduction of flue gas released from industrial plants had considered the microalgae as excellent biological materials for recycling the carbon dioxide directly emitted from exhaust industries. Microalgae also have the potential to be the valuable feedback for renewable energy production due to their high growth rate and abilities to sequester inorganic carbon through photosynthetic process. In this review article, we will illustrate important relative mechanisms in the metabolic processes of biofixation by microalgae and their recent experimental researches and advances of sequestration of carbon dioxide by microalgae on actual industrial and stimulate flue gases, novel photobioreactor cultivation systems as well as the perspectives and limitations of microalgal cultivation in further development.

Microalgae-based biorefinery--from biofuels to natural products.

PubMed

Yen, Hong-Wei; Hu, I-Chen; Chen, Chun-Yen; Ho, Shih-Hsin; Lee, Duu-Jong; Chang, Jo-Shu

2013-05-01

The potential for biodiesel production from microalgal lipids and for CO2 mitigation due to photoautotrophic growth of microalgae have recently been recognized. Microalgae biomass also has other valuable components, including carbohydrates, long chain fatty acids, pigments and proteins. The microalgae-based carbohydrates consist mainly of cellulose and starch without lignin; thus they can be ready carbon source for the fermentation industry. Some microalgae can produce long chain fatty acids (such as DHA and EPA) as valuable health food supplements. In addition, microalgal pigments and proteins have considerable potential for many medical applications. This review article presents comprehensive information on the current state of these commercial applications, as well as the utilization and characteristics of the microalgal components, in addition to the key factors and challenges that should be addressed during the production of these materials, and thus provides a useful report that can aid the development of an efficient microalgae-based biorefinery process. Copyright © 2012 Elsevier Ltd. All rights reserved.

An overview of microalgae industrial phycology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benemann, J.R.

1992-01-01

Microalgae, Chlorella, production for health foods has been an established industry in the Far East for over twenty five years. Since the mid-1970's, commercial Spirulina production has been carried out, first in Mexico, and since then by several companies, including two located in the United States. Spirulina is sold not only in the health food trade, but is also used in the extraction of food coloring agents and aquaculture feeds. Since the early 1980's, Dunaliella has been produced in the US, Australia, and Israel for its beta-carotene content. Microalgae are also being produced at a small scale for aquaculture feedsmore » and several companies are developing processes for the controlled cultivation of microalgae in bioreactors for speciality products, including essential fatty acids, pigments, diagnostic reagents, etc. The commercial applications of microalgae extend to wastewater treatment, including heavy metals removal. The steady progress of microalgae industrial phycology promises to continue in the coming years and decades.« less

Microalgae cultivation in sugarcane vinasse: Selection, growth and biochemical characterization.

PubMed

Santana, Hugo; Cereijo, Carolina R; Teles, Valérya C; Nascimento, Rodrigo C; Fernandes, Maiara S; Brunale, Patrícia; Campanha, Raquel C; Soares, Itânia P; Silva, Flávia C P; Sabaini, Priscila S; Siqueira, Félix G; Brasil, Bruno S A F

2017-03-01

Sugarcane ethanol is produced at large scale generating wastes that could be used for microalgae biomass production in a biorefinery strategy. In this study, forty microalgae strains were screened for growth in sugarcane vinasse at different concentrations. Two microalgae strains, Micractinium sp. Embrapa|LBA32 and C. biconvexa Embrapa|LBA40, presented vigorous growth in a light-dependent manner even in undiluted vinasse under non-axenic conditions. Microalgae strains presented higher biomass productivity in vinasse-based media compared to standard Bold's Basal Medium in cultures performed using 15L airlift flat plate photobioreactors. Chemical composition analyses showed that proteins and carbohydrates comprise the major fractions of algal biomass. Glucose was the main monosaccharide detected, ranging from 46% to 76% of the total carbohydrates content according to the strain and culture media used. This research highlights the potential of using residues derived from ethanol plants to cultivate microalgae for the production of energy and bioproducts. Copyright © 2016 Elsevier Ltd. All rights reserved.

In Metabolic Engineering of Eukaryotic Microalgae: Potential and Challenges Come with Great Diversity

PubMed Central

Gimpel, Javier A.; Henríquez, Vitalia; Mayfield, Stephen P.

2015-01-01

The great phylogenetic diversity of microalgae is corresponded by a wide arrange of interesting and useful metabolites. Nonetheless metabolic engineering in microalgae has been limited, since specific transformation tools must be developed for each species for either the nuclear or chloroplast genomes. Microalgae as production platforms for metabolites offer several advantages over plants and other microorganisms, like the ability of GMO containment and reduced costs in culture media, respectively. Currently, microalgae have proved particularly well suited for the commercial production of omega-3 fatty acids and carotenoids. Therefore most metabolic engineering strategies have been developed for these metabolites. Microalgal biofuels have also drawn great attention recently, resulting in efforts for improving the production of hydrogen and photosynthates, particularly triacylglycerides. Metabolic pathways of microalgae have also been manipulated in order to improve photosynthetic growth under specific conditions and for achieving trophic conversion. Although these pathways are not strictly related to secondary metabolites, the synthetic biology approaches could potentially be translated to this field and will also be discussed. PMID:26696985

Novel schemes for production of biodiesel and value-added co-products from microalgal oil using heterogeneous catalysts

NASA Astrophysics Data System (ADS)

Dong, Tao

Microalgae are promising sources of biofuels primarily because of their higher potential productivity compared to terrestrial biofuel crops. However, the production of liquid fuels from microalgae suffers from a lack of viable methods of extraction, conversion and fractionation of various components of the algal biomass. In this dissertation study, a rapid method was developed to accurately evaluate the biodiesel potential of microalgae biomass. The major advantage of this method is in situ fatty acid methyl ester (FAME) preparation directly from wet fresh microalgal and yeast biomass, without prior solvent extraction or dehydration. FAMEs were prepared by a sequential alkaline hydrolysis and acidic esterification process. This method can be used even with high amount of water in the biomass and is applicable to a vast range of microalgae and yeast species. A two-step in situ process was also investigated in this study to obtain a high FAME yield from microalgae biomass that had high free fatty acids (FFA) content. This process has the potential to reduce the production cost of microalgae-derived FAME and be more environmental compatible due to the higher FAME yield with reduced catalyst consumption. A cost-effective bio-char based catalyst was tested for the two-step biodiesel production. The results indicated that the bio-char catalyst was superior to commercial Amberly-15. A scalable chlorophyll remove process was also developed as a part of the system. The research resulted in a practical and cost-effective approach for producing biodiesel from crude microalgal oil. An integrated approach was explored in the fourth part of the study to produce biodiesel and fractionate high-value polyunsaturated fatty acid (PUFA). Zeolites were employed as the catalyst for selective esterification of fatty acids according to their chain length and degree of saturation. Low-value short chain FFA could be largely converted into FAME, while PUFA would remain unreacted due to steric hindrance. Both a high quality biodiesel and high-value PUFA could be obtained by employing this novel approach.

Enhancement of Biomass and Lipid Productivities of Water Surface-Floating Microalgae by Chemical Mutagenesis

PubMed Central

Nojima, Daisuke; Ishizuka, Yuki; Muto, Masaki; Ujiro, Asuka; Kodama, Fumito; Yoshino, Tomoko; Maeda, Yoshiaki; Matsunaga, Tadashi; Tanaka, Tsuyoshi

2017-01-01

Water surface-floating microalgae have great potential for biofuel applications due to the ease of the harvesting process, which is one of the most problematic steps in conventional microalgal biofuel production. We have collected promising water surface-floating microalgae and characterized their capacity for biomass and lipid production. In this study, we performed chemical mutagenesis of two water surface-floating microalgae to elevate productivity. Floating microalgal strains AVFF007 and FFG039 (tentatively identified as Botryosphaerella sp. and Chlorococcum sp., respectively) were exposed to ethyl methane sulfonate (EMS) or 1-methyl-3-nitro-1-nitrosoguanidine (MNNG), and pale green mutants (PMs) were obtained. The most promising FFG039 PM formed robust biofilms on the surface of the culture medium, similar to those formed by wild type strains, and it exhibited 1.7-fold and 1.9-fold higher biomass and lipid productivities than those of the wild type. This study indicates that the chemical mutation strategy improves the lipid productivity of water surface-floating microalgae without inhibiting biofilm formation and floating ability. PMID:28555001

Enhancement of Biomass and Lipid Productivities of Water Surface-Floating Microalgae by Chemical Mutagenesis.

PubMed

Nojima, Daisuke; Ishizuka, Yuki; Muto, Masaki; Ujiro, Asuka; Kodama, Fumito; Yoshino, Tomoko; Maeda, Yoshiaki; Matsunaga, Tadashi; Tanaka, Tsuyoshi

2017-05-27

Water surface-floating microalgae have great potential for biofuel applications due to the ease of the harvesting process, which is one of the most problematic steps in conventional microalgal biofuel production. We have collected promising water surface-floating microalgae and characterized their capacity for biomass and lipid production. In this study, we performed chemical mutagenesis of two water surface-floating microalgae to elevate productivity. Floating microalgal strains AVFF007 and FFG039 (tentatively identified as Botryosphaerella sp. and Chlorococcum sp., respectively) were exposed to ethyl methane sulfonate (EMS) or 1-methyl-3-nitro-1-nitrosoguanidine (MNNG), and pale green mutants (PMs) were obtained. The most promising FFG039 PM formed robust biofilms on the surface of the culture medium, similar to those formed by wild type strains, and it exhibited 1.7-fold and 1.9-fold higher biomass and lipid productivities than those of the wild type. This study indicates that the chemical mutation strategy improves the lipid productivity of water surface-floating microalgae without inhibiting biofilm formation and floating ability.

Simplified, rapid, and inexpensive estimation of water primary productivity based on chlorophyll fluorescence parameter Fo.

PubMed

Chen, Hui; Zhou, Wei; Chen, Weixian; Xie, Wei; Jiang, Liping; Liang, Qinlang; Huang, Mingjun; Wu, Zongwen; Wang, Qiang

2017-04-01

Primary productivity in water environment relies on the photosynthetic production of microalgae. Chlorophyll fluorescence is widely used to detect the growth status and photosynthetic efficiency of microalgae. In this study, a method was established to determine the Chl a content, cell density of microalgae, and water primary productivity by measuring chlorophyll fluorescence parameter Fo. A significant linear relationship between chlorophyll fluorescence parameter Fo and Chl a content of microalgae, as well as between Fo and cell density, was observed under pure-culture conditions. Furthermore, water samples collected from natural aquaculture ponds were used to validate the correlation between Fo and water primary productivity, which is closely related to Chl a content in water. Thus, for a given pure culture of microalgae or phytoplankton (mainly microalgae) in aquaculture ponds or other natural ponds for which the relationship between the Fo value and Chl a content or cell density could be established, Chl a content or cell density could be determined by measuring the Fo value, thereby making it possible to calculate the water primary productivity. It is believed that this method can provide a convenient way of efficiently estimating the primary productivity in natural aquaculture ponds and bringing economic value in limnetic ecology assessment, as well as in algal bloom monitoring. Copyright © 2017 Elsevier GmbH. All rights reserved.

Microalgae-activated sludge treatment of molasses wastewater in sequencing batch photo-bioreactor.

PubMed

Tsioptsias, Costas; Lionta, Gesthimani; Samaras, Petros

2017-05-01

The aim of this work was the examination of the treatment potential of molasses wastewater, by the utilization of activated sludge and microalgae. The systems used included a sequencing batch bioreactor and a similar photo-bioreactor, favoring microalgae growth. The microalgae treatment of molasses wastewater mixture resulted in a considerable reduction in the total nitrogen content. A reduction in the ammonium and nitrate content was observed in the photo-bioreactor, while the effluent's total nitrogen consisted mainly of 50% organic nitrogen. The transformation of the nitrogen forms in the photo-bioreactor was attributed to microalgae activity, resulting in the production of a better quality effluent. Lower COD removal was observed for the photo-bioreactor than the control, which however increased, by the replacement of the anoxic phase by a long aeration period. The mechanism of nitrogen removal included both the denitrification process during the anoxic stage and the microalgae activities, as the replacement of the anoxic stage resulted in low total nitrogen removal capacities. A decrease in the photobioreactor performance was observed after 35 days of operation due to biofilm formation on the light tube surface, while the operation at higher temperature accelerated microalgae growth, resulting thus in the early failure of the photoreactor.

Elevated CO2 concentration impacts cell wall polysaccharide composition of green microalgae of the genus Chlorella.

PubMed

Cheng, Y-S; Labavitch, J M; VanderGheynst, J S

2015-01-01

The effect of CO2 concentration on the relative content of starch, lipid and cell wall carbohydrates in microalgal biomass was investigated for the four following Chlorella strains: C. vulgaris (UTEX 259), C. sorokiniana (UTEX 2805), C. minutissima (UTEX 2341) and C. variabilis (NC64A). Each strain had a different response to CO2 concentration. The starch content was higher in UTEX259 and NC64A cultured with 2% CO2 in the air supply than in cells cultured with ca. 0·04% CO2 (ambient air), while starch content was not affected for UTEX 2805 and UTEX 2341. The lipid content was higher in Chlorella minutissima UTEX 2341 cultured in 2% CO2 than in cells cultured in ambient air, but was unchanged for the other three strains. All four Chlorella strains tended to have a higher percentage of uronic acids and lower percentage of neutral sugars in their cell wall polysaccharide complement when grown with 2% CO2 supply. Although the percentage of neutral sugars in the cell walls varied with CO2 concentration, the relative proportions of different neutral sugar constituents remained constant for both CO2 conditions. The results demonstrate the importance of considering the effects of CO2 on the cell wall carbohydrate composition of microalgae. Microalgae have the potential to produce products that will reduce society's reliance on fossil fuels and address challenges related to food and feed production. An overlooked yet industrially relevant component of microalgae are their cell walls. Cell wall composition affects cell flocculation and the recovery of intracellular products. In this study, we show that increasing CO2 level results in greater cell wall polysaccharide and uronic acid content in the cell walls of three strains of microalgae. The results have implications on the management of systems for the capture of CO2 and production of fuels, chemicals and food from microalgae. © 2014 The Society for Applied Microbiology.

Comparison between solar utilization of a closed microalgae-based bio-loop and that of a stand-alone photovoltaic system.

PubMed

Jin, Qiang; Chen, Lei; Li, Aimin; Liu, Fuqiang; Long, Chao; Shan, Aidang; Borthwick, Alistair G L

2015-05-01

This study compared the solar energy utilization of a closed microalgae-based bio-loop for energy efficient production of biogas with fertilizer recovery against that of a stand-alone photovoltaic (PV) system. The comparison was made from the perspective of broad life cycle assessment, simultaneously taking exergy to be the functional unit. The results indicated that the bio-loop was more environmentally competitive than an equivalent stand-alone PV system, but had higher economic cost due to high energy consumption during the operational phase. To fix the problem, a patented, interior pressurization scheduling method was used to operate the bio-loop, with microalgae and aerobic bacterial placed together in the same reactor. As a result, the overall environmental impact and total investment were respectively reduced by more than 75% and 84%, a vast improvement on the bio-loop. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biofuels from microalgae.

PubMed

Li, Yanqun; Horsman, Mark; Wu, Nan; Lan, Christopher Q; Dubois-Calero, Nathalie

2008-01-01

Microalgae are a diverse group of prokaryotic and eukaryotic photosynthetic microorganisms that grow rapidly due to their simple structure. They can potentially be employed for the production of biofuels in an economically effective and environmentally sustainable manner. Microalgae have been investigated for the production of a number of different biofuels including biodiesel, bio-oil, bio-syngas, and bio-hydrogen. The production of these biofuels can be coupled with flue gas CO2 mitigation, wastewater treatment, and the production of high-value chemicals. Microalgal farming can also be carried out with seawater using marine microalgal species as the producers. Developments in microalgal cultivation and downstream processing (e.g., harvesting, drying, and thermochemical processing) are expected to further enhance the cost-effectiveness of the biofuel from microalgae strategy.

Algicidal microorganisms and secreted algicides: New tools to induce microalgal cell disruption.

PubMed

Demuez, Marie; González-Fernández, Cristina; Ballesteros, Mercedes

2015-12-01

Cell disruption is one of the most critical steps affecting the economy and yields of biotechnological processes for producing biofuels from microalgae. Enzymatic cell disruption has shown competitive results compared to mechanical or chemical methods. However, the addition of enzymes implies an associated cost in the overall production process. Recent studies have employed algicidal microorganisms to perform enzymatic cell disruption and degradation of microalgae biomass in order to reduce this associated cost. Algicidal microorganisms induce microalgae growth inhibition, death and subsequent lysis. Secreted algicidal molecules and enzymes produced by bacteria, cyanobacteria, viruses and the microalga themselves that are capable of inducing algal death are classified, and the known modes of action are described along with insights into cell-to-cell interaction and communication. This review aims to provide information regarding microalgae degradation by microorganisms and secreted algicidal substances that would be useful for microalgae cell breakdown in biofuels production processes. A better understanding of algae-to-algae communication and the specific mechanisms of algal cell lysis is expected to be an important breakthrough for the broader application of algicidal microorganisms in biological cell disruption and the production of biofuels from microalgae biomass. Copyright © 2015 Elsevier Inc. All rights reserved.

Phytoremediation of agriculture runoff by filamentous algae poly-culture for biomethane production, and nutrient recovery for secondary cultivation of lipid generating microalgae.

PubMed

Bohutskyi, Pavlo; Chow, Steven; Ketter, Ben; Fung Shek, Coral; Yacar, Dean; Tang, Yuting; Zivojnovich, Mark; Betenbaugh, Michael J; Bouwer, Edward J

2016-12-01

An integrated system was implemented for water phytoremediation and biofuel production through sequential cultivation of filamentous algae followed by cultivation of lipid-producing microalgae Chlorella sorokiniana. Natural poly-culture of filamentous algae was grown in agricultural stormwater using the Algal Turf Scrubber®, harvested and subjected for lipid extraction and/or methane production using anaerobic digestion (AD). While filamentous algae lipid content was too low for feasible biodiesel production (<2%), both whole biomass and lipid-extracted algal residues (LEA) yielded ∼0.2LmethanepergVS at loading rates up to 5gVS/L-day. Importantly, essential macro-nutrients and trace elements captured from stormwater were released into the AD effluent as soluble nutrients and were successfully tested as fertilizer replacement for cultivation of lipid-accumulating C. sorokiniana in a subsequent stage. Accordingly, filamentous algae poly-culture was exploited for waste nutrient capturing and biofuel feedstock generation. These nutrients were recovered and reused as a concentrated supplement for potentially high-value microalgae. Published by Elsevier Ltd.

Theoretical Calculations on the Feasibility of Microalgal Biofuels: Utilization of Marine Resources Could Help Realizing the Potential of Microalgae

PubMed Central

Park, Hanwool

2016-01-01

Abstract Microalgae have long been considered as one of most promising feedstocks with better characteristics for biofuels production over conventional energy crops. There have been a wide range of estimations on the feasibility of microalgal biofuels based on various productivity assumptions and data from different scales. The theoretical maximum algal biofuel productivity, however, can be calculated by the amount of solar irradiance and photosynthetic efficiency (PE), assuming other conditions are within the optimal range. Using the actual surface solar irradiance data around the world and PE of algal culture systems, maximum algal biomass and biofuel productivities were calculated, and feasibility of algal biofuel were assessed with the estimation. The results revealed that biofuel production would not easily meet the economic break‐even point and may not be sustainable at a large‐scale with the current algal biotechnology. Substantial reductions in the production cost, improvements in lipid productivity, recycling of resources, and utilization of non‐conventional resources will be necessary for feasible mass production of algal biofuel. Among the emerging technologies, cultivation of microalgae in the ocean shows great potentials to meet the resource requirements and economic feasibility in algal biofuel production by utilizing various marine resources. PMID:27782372

Theoretical Calculations on the Feasibility of Microalgal Biofuels: Utilization of Marine Resources Could Help Realizing the Potential of Microalgae.

PubMed

Park, Hanwool; Lee, Choul-Gyun

2016-11-01

Microalgae have long been considered as one of most promising feedstocks with better characteristics for biofuels production over conventional energy crops. There have been a wide range of estimations on the feasibility of microalgal biofuels based on various productivity assumptions and data from different scales. The theoretical maximum algal biofuel productivity, however, can be calculated by the amount of solar irradiance and photosynthetic efficiency (PE), assuming other conditions are within the optimal range. Using the actual surface solar irradiance data around the world and PE of algal culture systems, maximum algal biomass and biofuel productivities were calculated, and feasibility of algal biofuel were assessed with the estimation. The results revealed that biofuel production would not easily meet the economic break-even point and may not be sustainable at a large-scale with the current algal biotechnology. Substantial reductions in the production cost, improvements in lipid productivity, recycling of resources, and utilization of non-conventional resources will be necessary for feasible mass production of algal biofuel. Among the emerging technologies, cultivation of microalgae in the ocean shows great potentials to meet the resource requirements and economic feasibility in algal biofuel production by utilizing various marine resources. © 2016 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Metabolic Engineering of Microalgal Based Biofuel Production: Prospects and Challenges.

PubMed

Banerjee, Chiranjib; Dubey, Kashyap K; Shukla, Pratyoosh

2016-01-01

The current scenario in renewable energy is focused on development of alternate and sustainable energy sources, amongst which microalgae stands as one of the promising feedstock for biofuel production. It is well known that microalgae generate much larger amounts of biofuels in a shorter time than other sources based on plant seeds. However, the greatest challenge in a transition to algae-based biofuel production is the various other complications involved in microalgal cultivation, its harvesting, concentration, drying and lipid extraction. Several green microalgae accumulate lipids, especially triacylglycerols (TAGs), which are main precursors in the production of lipid. The various aspects on metabolic pathway analysis of an oleaginous microalgae i.e., Chlamydomonas reinhardtii have elucidated some novel metabolically important genes and this enhances the lipid production in this microalgae. Adding to it, various other aspects in metabolic engineering using OptFlux and effectual bioprocess design also gives an interactive snapshot of enhancing lipid production which ultimately improvises the oil yield. This article reviews the current status of microalgal based technologies for biofuel production, bioreactor process design, flux analysis and it also provides various strategies to increase lipids accumulation via metabolic engineering.

Strategies for Lipid Production Improvement in Microalgae as a Biodiesel Feedstock

PubMed Central

Li, Z. H.; Hiltunen, E.

2016-01-01

In response to the energy crisis, global warming, and climate changes, microalgae have received a great deal of attention as a biofuel feedstock. Due to a high lipid content in microalgal cells, microalgae present as a promising alternative source for the production of biodiesel. Environmental and culturing condition variations can alter lipid production as well as chemical compositions of microalgae. Therefore, application of the strategies to activate lipid accumulation opens the door for lipid overproduction in microalgae. Until now, many original studies regarding the approaches for enhanced microalgal lipid production have been reported in an effort to push forward the production of microalgal biodiesel. However, the current literature demonstrates fragmented information available regarding the strategies for lipid production improvement. From the systematic point of view, the review highlights the main approaches for microalgal lipid accumulation induction to expedite the application of microalgal biodiesel as an alternative to fossil diesel for sustainable environment. Of the several strategies discussed, the one that is most commonly applied is the design of nutrient (e.g., nitrogen, phosphorus, and sulfur) starvation or limitation. Other viable approaches such as light intensity, temperature, carbon dioxide, salinity stress, and metal influence can also achieve enhanced microalgal lipid production. PMID:27725942

Strategies for Lipid Production Improvement in Microalgae as a Biodiesel Feedstock.

PubMed

Zhu, L D; Li, Z H; Hiltunen, E

2016-01-01

In response to the energy crisis, global warming, and climate changes, microalgae have received a great deal of attention as a biofuel feedstock. Due to a high lipid content in microalgal cells, microalgae present as a promising alternative source for the production of biodiesel. Environmental and culturing condition variations can alter lipid production as well as chemical compositions of microalgae. Therefore, application of the strategies to activate lipid accumulation opens the door for lipid overproduction in microalgae. Until now, many original studies regarding the approaches for enhanced microalgal lipid production have been reported in an effort to push forward the production of microalgal biodiesel. However, the current literature demonstrates fragmented information available regarding the strategies for lipid production improvement. From the systematic point of view, the review highlights the main approaches for microalgal lipid accumulation induction to expedite the application of microalgal biodiesel as an alternative to fossil diesel for sustainable environment. Of the several strategies discussed, the one that is most commonly applied is the design of nutrient (e.g., nitrogen, phosphorus, and sulfur) starvation or limitation. Other viable approaches such as light intensity, temperature, carbon dioxide, salinity stress, and metal influence can also achieve enhanced microalgal lipid production.

Challenges and opportunities for hydrogen production from microalgae.

PubMed

Oey, Melanie; Sawyer, Anne Linda; Ross, Ian Lawrence; Hankamer, Ben

2016-07-01

The global population is predicted to increase from ~7.3 billion to over 9 billion people by 2050. Together with rising economic growth, this is forecast to result in a 50% increase in fuel demand, which will have to be met while reducing carbon dioxide (CO2 ) emissions by 50-80% to maintain social, political, energy and climate security. This tension between rising fuel demand and the requirement for rapid global decarbonization highlights the need to fast-track the coordinated development and deployment of efficient cost-effective renewable technologies for the production of CO2 neutral energy. Currently, only 20% of global energy is provided as electricity, while 80% is provided as fuel. Hydrogen (H2 ) is the most advanced CO2 -free fuel and provides a 'common' energy currency as it can be produced via a range of renewable technologies, including photovoltaic (PV), wind, wave and biological systems such as microalgae, to power the next generation of H2 fuel cells. Microalgae production systems for carbon-based fuel (oil and ethanol) are now at the demonstration scale. This review focuses on evaluating the potential of microalgal technologies for the commercial production of solar-driven H2 from water. It summarizes key global technology drivers, the potential and theoretical limits of microalgal H2 production systems, emerging strategies to engineer next-generation systems and how these fit into an evolving H2 economy. © 2016 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Integration process of biodiesel production from filamentous oleaginous microalgae Tribonema minus.

PubMed

Wang, Hui; Gao, Lili; Chen, Lin; Guo, Fajin; Liu, Tianzhong

2013-08-01

Biodiesel production from microalgae has been receiving considerable attention. Past studies mainly relied on tiny sized single-cell oleaginous microalgal species, the biodiesel based on filamentous oleaginous microalgae was rarely reported. Thus, integrated process of biodiesel production from filamentous oleaginous microalgal strain Tribonema minus was studied in this work. The filamentous microalgae was cultivated for 21 days in 40 L glass panel, microalgae cells was harvested by DAF without any flocculants after the lipid content was 50.23%. After that, total lipid was extracted by subcritical ethanol from wet algal paste and 44.55% of crude lipid was triacylglycerols. Two-step catalytic conversion of pre-esterification and transesterification was adopted to convert the crude algal oil to biodiesel. The conversion rate of triacylglycerols reached 96.52% under the methanol to oil molar ratio of 12:1 during catalysis with 2% potassium hydroxide at 65°C for 30 min. The biodiesel product from T. minus conformed to Chinese National Standards. Copyright © 2013 Elsevier Ltd. All rights reserved.

Influence of variable water depth and turbidity on microalgae production in a shallow estuarine lake system - A modelling study

NASA Astrophysics Data System (ADS)

Tirok, Katrin; Scharler, Ursula M.

2014-06-01

Strongly varying water levels and turbidities are typical characteristics of the large shallow estuarine lake system of St. Lucia, one of the largest on the African continent. This theoretical study investigated the combined effects of variable water depth and turbidity on seasonal pelagic and benthic microalgae production using a mathematical model, in order to ascertain productivity levels during variable and extreme conditions. Simulated pelagic and benthic net production varied between 0.3 and 180 g C m-2 year-1 and 0 and 220 g C m-2 year-1, respectively, dependent on depth, turbidity, and variability in turbidity. Although not surprising production and biomass decreased with increasing turbidity and depth. A high variability in turbidity, i.e. an alteration of calm and windy days, could reduce or enhance the seasonal pelagic and benthic production by more than 30% compared to a low variability. The day-to-day variability in wind-induced turbidity therefore influences production in the long term. On the other hand, varying water depth within a year did not significantly influence the seasonal production for turbidities representative of Lake St. Lucia. Reduced lake area and volume as observed during dry periods in Lake St. Lucia did not reduce primary production of the entire system since desiccation resulted in lower water depth and thus increased light availability. This agrees with field observations suggesting little light limitation and high areal microalgal biomass during a period with below average rainfall (2005-2011). Thus, microalgae potentially fulfil their function in the lake food-web even under extreme drought conditions. We believe that these results are of general interest to shallow aquatic ecosystems that are sensitive to drought periods due to either human or natural causes.

Quorum sensing of microalgae associated marine Ponticoccus sp. PD-2 and its algicidal function regulation.

PubMed

Chi, Wendan; Zheng, Li; He, Changfei; Han, Bin; Zheng, Minggang; Gao, Wei; Sun, Chengjun; Zhou, Gefei; Gao, Xiangxing

2017-12-01

Quorum sensing (QS) systems play important roles in regulating many physiological functions of microorganisms, such as biofilm formation, bioluminescence, and antibiotic production. One marine algicidal bacterium, Ponticoccus sp. PD-2, was isolated from the microalga Prorocentrum donghaiense, and its N-acyl-homoserine lactone (AHL)-mediated QS system was verified. In this study, we analyzed the AHLs profile of strain PD-2. Two AHLs, 3-oxo-C8-HSL and 3-oxo-C10-HSL, were detected using a biosensor overlay assay and GC-MS methods. Two complete AHL-QS systems (designated zlaI/R and zlbI/R) were identified in the genome of strain PD-2. When expressed in Escherichia coli, both zlaI and zlbI genes could each produce 3-oxo-C8-HSL and 3-oxo-C10-HSL. Algicidal activity was investigated by evaluating the inhibitory rate (IR) of microalgae growth by measuring the fluorescence of viable cells. We found that the metabolites of strain PD-2 had algicidal activity against its host P. donghaiense (IR 84.81%) and two other red tide microalgae, Phaeocystis globosa (IR 78.91%) and Alexandrium tamarense (IR 67.14%). β-cyclodextrin which binds to AHLs and inhibits the QS system reduced the algicidal activity more than 50%. This indicates that inhibiting the QS system may affect the algicidal metabolites production of strain PD-2. Our study indicated that a QS-regulated algicidal system may play a potential role in the process of red tides disintegration. QS might be a potential way to control red tides.

A novel microalgal lipid extraction method using biodiesel (fatty acid methyl esters) as an extractant.

PubMed

Huang, Wen-Can; Park, Chan Woo; Kim, Jong-Duk

2017-02-01

Although microalgae are considered promising renewable sources of biodiesel, the high cost of the downstream process is a significant obstacle in large-scale biodiesel production. In this study, a novel approach for microalgal biodiesel production was developed by using the biodiesel as an extractant. First, wet microalgae with 70% water content were incubated with a mixture of biodiesel/methanol and penetration of the mixture through the cell membrane and swelling of the lipids contained in microalgae was confirmed. Significant increases of lipid droplets were observed by confocal microscopy. Second, the swelled lipid droplets in microalgae were squeezed out using mechanical stress across the cell membrane and washed with methanol. The lipid extraction efficiency reached 68%. This process does not require drying of microalgae or solvent recovery, which the most energy-intensive step in solvent-based biodiesel production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Water use and its recycling in microalgae cultivation for biofuel application.

PubMed

Farooq, Wasif; Suh, William I; Park, Min S; Yang, Ji-Won

2015-05-01

Microalgal biofuels are not yet economically viable due to high material and energy costs associated with production process. Microalgae cultivation is a water-intensive process compared to other downstream processes for biodiesel production. Various studies found that the production of 1 L of microalgal biodiesel requires approximately 3000 L of water. Water recycling in microalgae cultivation is desirable not only to reduce the water demand, but it also improves the economic feasibility of algal biofuels as due to nutrients and energy savings. This review highlights recently published studies on microalgae water demand and water recycling in microalgae cultivation. Strategies to reduce water footprint for microalgal cultivation, advantages and disadvantages of water recycling, and approaches to mitigate the negative effects of water reuse within the context of water and energy saving are also discussed. Copyright © 2014 Elsevier Ltd. All rights reserved.

Temperature-sensitive PSII: a novel approach for sustained photosynthetic hydrogen production.

PubMed

Bayro-Kaiser, Vinzenz; Nelson, Nathan

2016-12-01

The need for energy and the associated burden are ever growing. It is crucial to develop new technologies for generating clean and efficient energy for society to avoid upcoming energetic and environmental crises. Sunlight is the most abundant source of energy on the planet. Consequently, it has captured our interest. Certain microalgae possess the ability to capture solar energy and transfer it to the energy carrier, H 2 . H 2 is a valuable fuel, because its combustion produces only one by-product: water. However, the establishment of an efficient biophotolytic H 2 production system is hindered by three main obstacles: (1) the hydrogen-evolving enzyme, [FeFe]-hydrogenase, is highly sensitive to oxygen; (2) energy conversion efficiencies are not economically viable; and (3) hydrogen-producing organisms are sensitive to stressful conditions in large-scale production systems. This study aimed to circumvent the oxygen sensitivity of this process with a cyclic hydrogen production system. This approach required a mutant that responded to high temperatures by reducing oxygen evolution. To that end, we randomly mutagenized the green microalgae, Chlamydomonas reinhardtii, to generate mutants that exhibited temperature-sensitive photoautotrophic growth. The selected mutants were further characterized by their ability to evolve oxygen and hydrogen at 25 and 37 °C. We identified four candidate mutants for this project. We characterized these mutants with PSII fluorescence, P700 absorbance, and immunoblotting analyses. Finally, we demonstrated that these mutants could function in a prototype hydrogen-producing bioreactor. These mutant microalgae represent a novel approach for sustained hydrogen production.

Growth Kinetics for Microalgae Grown in Palm Oil Mill Effluent (POME) medium at various CO2 Levels

NASA Astrophysics Data System (ADS)

Razali, S.; Salihon, J.; Ahmad, M. A.

2018-05-01

This paper sought to find the growth kinetic data of maximum specific growth rate (μmax) and substrate saturation constant (KS) for a microalgal reaction system over various dissolved CO2 levels (0.04, 0.1, 0.3, 0.5, 0.8, 1.0, 5.0, 10.0% v/v) at a constant sparging rate of 1.2 vvm, by using logistic model and Monod kinetics. The reaction system consisted of microalgae growing in palm oil mill effluent (POME) medium in 1 L flask with constant light illumination and sparged with the specified CO2 gas mixture. It is found from the experimental works that the values of μmax and KS to be at 0.04958 h-1 and 0.03523% (v/v) respectively. The results also showed that utilizing CO2 levels (v/v) in the sparging gas mixture more than 1% (v/v) would not improve microalgae growth significantly as expressed in the values of specific growth rate µ. These data and information are critically important for bioreactor scaling up purposes, especially bioreactor system dedicated for microalgae products and CO2 sequestration.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. T. Nakamura; Dr. Miguel Olaizola; Dr. Stephen M. Masutani

Most of the anthropogenic emissions of carbon dioxide result from the combustion of fossil fuels for energy production. Photosynthesis has long been recognized as a means, at least in theory, to sequester anthropogenic carbon dioxide. Aquatic microalgae have been identified as fast growing species whose carbon fixing rates are higher than those of land-based plants by one order of magnitude. Physical Sciences Inc. (PSI), Aquasearch, and the Hawaii Natural Energy Institute at the University of Hawaii are jointly developing technologies for recovery and sequestration of CO{sub 2} from stationary combustion systems by photosynthesis of microalgae. The research is aimed primarilymore » at demonstrating the ability of selected species of microalgae to effectively fix carbon from typical power plant exhaust gases. This report is the summary first year report covering the reporting period 1 October 2000 to 30 September 2001 in which PSI, Aquasearch and University of Hawaii conducted their tasks. Based on the work conducted during the previous reporting period, PSI initiated work on the component optimization work. Aquasearch continued their effort on selection of microalgae suitable for CO{sub 2} sequestration. University of Hawaii initiated effort on system optimization of the CO{sub 2} sequestration system.« less

Understanding the biological activity of high rate algae ponds through the calculation of oxygen balances.

PubMed

Arbib, Zouhayr; de Godos Crespo, Ignacio; Corona, Enrique Lara; Rogalla, Frank

2017-06-01

Microalgae culture in high rate algae ponds (HRAP) is an environmentally friendly technology for wastewater treatment. However, for the implementation of these systems, a better understanding of the oxygenation potential and the influence of climate conditions is required. In this work, the rates of oxygen production, consumption, and exchange with the atmosphere were calculated under varying conditions of solar irradiance and dilution rate during six months of operation in a real scale unit. This analysis allowed determining the biological response of these dynamic systems. The rates of oxygen consumption measured were considerably higher than the values calculated based on the organic loading rate. The response to light intensity in terms of oxygen production in the bioreactor was described with one of the models proposed for microalgae culture in dense concentrations. This model is based on the availability of light inside the culture and the specific response of microalgae to this parameter. The specific response to solar radiation intensity showed a reasonable stability in spite of the fluctuations due to meteorological conditions. The methodology developed is a useful tool for optimization and prediction of the performance of these systems.

Microalgal hydrogen production - A review.

PubMed

Khetkorn, Wanthanee; Rastogi, Rajesh P; Incharoensakdi, Aran; Lindblad, Peter; Madamwar, Datta; Pandey, Ashok; Larroche, Christian

2017-11-01

Bio-hydrogen from microalgae including cyanobacteria has attracted commercial awareness due to its potential as an alternative, reliable and renewable energy source. Photosynthetic hydrogen production from microalgae can be interesting and promising options for clean energy. Advances in hydrogen-fuel-cell technology may attest an eco-friendly way of biofuel production, since, the use of H 2 to generate electricity releases only water as a by-product. Progress in genetic/metabolic engineering may significantly enhance the photobiological hydrogen production from microalgae. Manipulation of competing metabolic pathways by modulating the certain key enzymes such as hydrogenase and nitrogenase may enhance the evolution of H 2 from photoautotrophic cells. Moreover, biological H 2 production at low operating costs is requisite for economic viability. Several photobioreactors have been developed for large-scale biomass and hydrogen production. This review highlights the recent technological progress, enzymes involved and genetic as well as metabolic engineering approaches towards sustainable hydrogen production from microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

Microalgal biomass production pathways: evaluation of life cycle environmental impacts.

PubMed

Zaimes, George G; Khanna, Vikas

2013-06-20

Microalgae are touted as an attractive alternative to traditional forms of biomass for biofuel production, due to high productivity, ability to be cultivated on marginal lands, and potential to utilize carbon dioxide (CO2) from industrial flue gas. This work examines the fossil energy return on investment (EROIfossil), greenhouse gas (GHG) emissions, and direct Water Demands (WD) of producing dried algal biomass through the cultivation of microalgae in Open Raceway Ponds (ORP) for 21 geographic locations in the contiguous United States (U.S.). For each location, comprehensive life cycle assessment (LCA) is performed for multiple microalgal biomass production pathways, consisting of a combination of cultivation and harvesting options. Results indicate that the EROIfossil for microalgae biomass vary from 0.38 to 1.08 with life cycle GHG emissions of -46.2 to 48.9 (g CO2 eq/MJ-biomass) and direct WDs of 20.8 to 38.8 (Liters/MJ-biomass) over the range of scenarios analyzed. Further anaylsis reveals that the EROIfossil for production pathways is relatively location invariant, and that algae's life cycle energy balance and GHG impacts are highly dependent on cultivation and harvesting parameters. Contrarily, algae's direct water demands were found to be highly sensitive to geographic location, and thus may be a constraining factor in sustainable algal-derived biofuel production. Additionally, scenarios with promising EROIfossil and GHG emissions profiles are plagued with high technological uncertainty. Given the high variability in microalgae's energy and environmental performance, careful evaluation of the algae-to-fuel supply chain is necessary to ensure the long-term sustainability of emerging algal biofuel systems. Alternative production scenarios and technologies may have the potential to reduce the critical demands of biomass production, and should be considered to make algae a viable and more efficient biofuel alternative.

Removal of metal from acid mine drainage using a hybrid system including a pipes inserted microalgae reactor.

PubMed

Park, Young-Tae; Lee, Hongkyun; Yun, Hyun-Shik; Song, Kyung-Guen; Yeom, Sung-Ho; Choi, Jaeyoung

2013-12-01

In this study, the microalgae culture system to combined active treatment system and pipe inserted microalgae reactor (PIMR) was investigated. After pretreated AMD in active treatment system, the effluent load to PIMR in order to Nephroselmis sp. KGE 8 culture. In experiment, effect of iron on growth and lipid accumulation in microalgae were inspected. The 2nd pretreatment effluent was economic feasibility of microalgae culture and lipid accumulation. The growth kinetics of the microalgae are modeled using logistic growth model and the model is primarily parameterized from data obtained through an experimental study where PIMR were dosed with BBM, BBM added 10 mg L(-1) iron and 2nd pretreatment effluent. Moreover, the continuous of microalgae culture in PIMR can be available. Overall, this study indicated that the use of pretreated AMD is a viable method for culture microalgae and lipid accumulation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Lipid extraction of wet BLT0404 microalgae for biofuel application

NASA Astrophysics Data System (ADS)

Mansur, Dieni; Fitriady, Muhammad Arifuddin; Susilaningsih, Dwi; Simanungkalit, Sabar Pangihutan; Agustian, Egi

2017-01-01

Recently, research and development of microalgae for biodiesel production were conducted by researchers in the world. This research becomes popular because of an exponential growth of the microalgae under nutrient limitation. Lipid of microalgae grows faster than oil producing land crops. Therefore, microalgae lipid content could improve the economics of biodiesel production. The aim of this study was to investigate yield of lipid extract and chemicals compounds containing in non-acylglycerol neutral lipid from BLT 0404 microalga. The study was conducted because lipid extraction was an important step for biodiesel as well as biofuel production. The extraction was carried out using polar and non-polar mixture solvents. The polar solvent was methanol and non-polar one was chloroform. Process extraction was conducted under various stirring time between the microalgae and methanol and volume ratio between the methanol and chloroform. Methanol as a polar solvent was able to extract polar lipid (phospholipid and glycolipid) because it removed polar membrane lipid and lipid-associated to polar molecule. Moreover, the non-polar solvent was used for extraction non-acylglycerol neutral lipid (hydrocarbons, sterols, ketones, free fatty acids, carotenes, and chlorophylls) for biofuel production. Under ratio of microalgae: methanol: chloroform of 0.8: 4: 2 that stirring time of the microalgae with methanol was 30 min yielded 58% of total lipid extract. The yield value consisted of 14.5% of non-acylglycerol neutral lipid and 43.5% of polar lipid. The non-acylglycerol neutral lipid will be converted into biofuel. Therefore, analysis of its chemical compounds was required. The non-acylglycerol neutral lipid was analyzed by GCMS and found that the extract contained long chains of hydrocarbon compounds. The hydrocarbons consisted of C18-C30 that high peaks with larger percentage area were C20-C26. The results suggested that stirring between microalgae and methanol for 30 min was needed before additional of chloroform. Moreover, the ratio of methanol must be higher than chloroform due to the higher portion of polar lipid content in the microalgae.

Physiological-phased kinetic characteristics of microalgae Chlorella vulgaris growth and lipid synthesis considering synergistic effects of light, carbon and nutrients.

PubMed

Liao, Qiang; Chang, Hai-Xing; Fu, Qian; Huang, Yun; Xia, Ao; Zhu, Xun; Zhong, Nianbing

2018-02-01

To comprehensively understand kinetic characteristics of microalgae growth and lipid synthesis in different phases, a phase-feeding strategy was proposed to simultaneously regulate light, carbon and nutrients in adaption, growth and stationary phases of microalgae cultivation. Physiological-phased kinetic characteristics of microalgae Chlorella vulgaris growth and lipid synthesis under synergistic effects of light, carbon and nutrients were investigated, and supply-demand relationships of electrons and energy between light and dark reactions of photosynthesis process were discussed. Finally, the optimized cultivation strategy for microalgae in various phases were obtained, under which the lipid productivity was significantly improved from 130.11 mg/L/d to 163.42 mg/L/d. The study provided some important guidance for the large-scale production of biofuels from microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

Environmental building policy by the use of microalgae and decreasing of risks for Canadian oil sand sector development.

PubMed

Avagyan, Armen B

2017-09-01

Environmental building recommendations aimed towards new environmental policies and management-changing decisions which as example demonstrated in consideration of the problems of Canadian oil sands operators. For the implementation of the circular economic strategy, we use an in-depth analysis of reported environmental after-consequence on all stages of the production process. The study addressed the promotion of innovative solutions for greenhouse gas emission, waste mitigation, and risk of falling in oil prices for operators of oil sands with creating market opportunities. They include the addition of microalgae biomass in tailings ponds for improvement of the microbial balance for the water speedily cleaning, recycling, and reusing with mitigation of GHG emissions. The use of food scraps for the nutrition of microalgae will reduce greenhouse gas emission minimally, on 0.33 MtCO 2 eq for Alberta and 2.63 MtCO 2 eq/year for Canada. Microalgae-derived biofuel can reduce this emission for Alberta on 11.9-17.9 MtCO 2 eq and for Canada on 71-106 MtCO 2 eq/year, and the manufacturing of other products will adsorb up to 135.6 MtCO 2 and produce 99.2 MtO 2 . The development of the Live Conserve Industry and principal step from non-efficient protection of the environment to its cultivation in a large scale with mitigation of GHG emission and waste as well as generating of O 2 and value-added products by the use of microalgae opens an important shift towards a new design and building of a biological system.

Lipid production of microalga Chlorella sorokiniana CY1 is improved by light source arrangement, bioreactor operation mode and deep-sea water supplements.

PubMed

Chen, Chun-Yen; Chang, Hsin-Yueh

2016-03-01

Microalgae-based biodiesel has been recognized as a sustainable and promising alternative to fossil diesel. High lipid productivity of microalgae is required for economic production of biodiesel from microalgae. This study was undertaken to enhance the growth and oil accumulation of an indigenous microalga Chlorella sorokiniana CY1 by applying engineering strategies using deep-sea water as the medium. First, the microalga was cultivated using LED as the immersed light source, and the results showed that the immersed LED could effectively enhance the oil/lipid content and final microalgal biomass concentration to 53.8% and 2.5 g/l, respectively. Next, the semi-batch photobioreactor operation with deep-sea water was shown to improve lipid content and microalgal growth over those from using batch and continuous cultures under similar operating conditions. The optimal replacement ratio was 50%, resulting in an oil/lipid content and final biomass concentration of 61.5% and 2.8 g/l, respectively. A long-term semi-batch culture utilizing 50%-replaced medium was carried out for four runs. The final biomass concentration and lipid productivity were 2.5 g/L and 112.2 mg/L/d, respectively. The fatty acid composition of the microalgal lipids was predominant by palmitic acid, stearic acid, oleic acid and linoleic acid, and this lipid quality is suitable for biodiesel production. This demonstrates that optimizing light source arrangement, bioreactor operation and deep-sea water supplements could effectively promote the lipid production of C. sorokiniana CY1 for the applications in microalgae-based biodiesel industry. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analysis of Autophagy Genes in Microalgae: Chlorella as a Potential Model to Study Mechanism of Autophagy

PubMed Central

Jiang, Qiao; Zhao, Li; Dai, Junbiao; Wu, Qingyu

2012-01-01

Background Microalgae, with the ability to mitigate CO2 emission and produce carbohydrates and lipids, are considered one of the most promising resources for producing bioenergy. Recently, we discovered that autophagy plays a critical role in the metabolism of photosynthetic system and lipids production. So far, more than 30-autophagy related (ATG) genes in all subtypes of autophagy have been identified. However, compared with yeast and mammals, in silico and experimental research of autophagy pathways in microalgae remained limited and fragmentary. Principal Findings In this article, we performed a genome-wide analysis of ATG genes in 7 microalgae species and explored their distributions, domain structures and evolution. Eighteen “core autophagy machinery” proteins, four mammalian-specific ATG proteins and more than 30 additional proteins (including “receptor-adaptor” complexes) in all subtypes of autophagy were analyzed. Data revealed that receptor proteins in cytoplasm-to-vacuole targeting and mitophagy seem to be absent in microalgae. However, most of the “core autophagy machinery” and mammalian-specific proteins are conserved among microalgae, except for the ATG9-cycling system in Chlamydomonas reinhardtii and the second ubiquitin-like protein conjugation complex in several algal species. The catalytic and binding residues in ATG3, ATG5, ATG7, ATG8, ATG10 and ATG12 are also conserved and the phylogenetic tree of ATG8 coincides well with the phylogenies. Chlorella contains the entire set of the core autophagy machinery. In addition, RT-PCR analysis verified that all crucial ATG genes tested are expressed during autophagy in both Chlorella and Chlamydomonas reinhardtii. Finally, we discovered that addition of 3-Methyladenine (a PI3K specific inhibitor) could suppress the formation of autophagic vacuoles in Chlorella. Conclusions Taken together, Chlorella may represent a potential model organism to investigate autophagy pathways in photosynthetic eukaryotes. The study will not only promote understanding of the general features of autophagic pathways, but also benefit the production of Chlorella-derived biofuel with future commercial applications. PMID:22848622

Micro-algae come of age as a platform for recombinant protein production

PubMed Central

Specht, Elizabeth; Miyake-Stoner, Shigeki

2010-01-01

A complete set of genetic tools is still being developed for the micro-alga Chlamydomonas reinhardtii. Yet even with this incomplete set, this photosynthetic single-celled plant has demonstrated significant promise as a platform for recombinant protein expression. In recent years, techniques have been developed that allow for robust expression of genes from both the nuclear and plastid genome. With these advances, many research groups have examined the pliability of this and other micro-algae as biological machines capable of producing recombinant peptides and proteins. This review describes recent successes in recombinant protein production in Chlamydomonas, including production of complex mammalian therapeutic proteins and monoclonal antibodies at levels sufficient for production at economic parity with existing production platforms. These advances have also shed light on the details of algal protein production at the molecular level, and provide insight into the next steps for optimizing micro-algae as a useful platform for the production of therapeutic and industrially relevant recombinant proteins. PMID:20556634

Regulation of Oil Biosynthesis in Algae

DTIC Science & Technology

2011-03-14

transportation fuels can potentially be addressed by exploring oil (triacylglycerol) biosynthesis in microalgae . Many microalgae , including Chlamydomonas...biosynthesis in microalgae have not been studied at the molecular level. Chlamydomonas is being used as a microalgal model to identify genes and regulatory...of this phenomenon will shed light on the physiological significance of oil production in microalgae . A first paper describing this interesting

Direct biodiesel production from wet microalgae biomass of Chlorella pyrenoidosa through in situ transesterification.

PubMed

Cao, Hechun; Zhang, Zhiling; Wu, Xuwen; Miao, Xiaoling

2013-01-01

A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production.

Recent Developments on Genetic Engineering of Microalgae for Biofuels and Bio-Based Chemicals.

PubMed

Ng, I-Son; Tan, Shih-I; Kao, Pei-Hsun; Chang, Yu-Kaung; Chang, Jo-Shu

2017-10-01

Microalgae serve as a promising source for the production of biofuels and bio-based chemicals. They are superior to terrestrial plants as feedstock in many aspects and their biomass is naturally rich in lipids, carbohydrates, proteins, pigments, and other valuable compounds. Due to the relatively slow growth rate and high cultivation cost of microalgae, to screen efficient and robust microalgal strains as well as genetic modifications of the available strains for further improvement are of urgent demand in the development of microalgae-based biorefinery. In genetic engineering of microalgae, transformation and selection methods are the key steps to accomplish the target gene modification. However, determination of the preferable type and dosage of antibiotics used for transformant selection is usually time-consuming and microalgal-strain-dependent. Therefore, more powerful and efficient techniques should be developed to meet this need. In this review, the conventional and emerging genome-editing tools (e.g., CRISPR-Cas9, TALEN, and ZFN) used in editing the genomes of nuclear, mitochondria, and chloroplast of microalgae are thoroughly surveyed. Although all the techniques mentioned above demonstrate their abilities to perform gene editing and desired phenotype screening, there still need to overcome higher production cost and lower biomass productivity, to achieve efficient production of the desired products in microalgal biorefineries. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Direct Biodiesel Production from Wet Microalgae Biomass of Chlorella pyrenoidosa through In Situ Transesterification

PubMed Central

Cao, Hechun; Zhang, Zhiling; Wu, Xuwen; Miao, Xiaoling

2013-01-01

A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production. PMID:24195081

Optimization of Chlorella vulgaris and bioflocculant-producing bacteria co-culture: enhancing microalgae harvesting and lipid content.

PubMed

Wang, Y; Yang, Y; Ma, F; Xuan, L; Xu, Y; Huo, H; Zhou, D; Dong, S

2015-05-01

Microalgae are a sustainable bioresource, and the biofuel they produce is widely considered to be an alternative to limited natural fuel resources. However, microalgae harvesting is a bottleneck in the development of technology. Axenic Chlorella vulgaris microalgae exhibit poor harvesting, as expressed by a flocculation efficiency of 0·2%. This work optimized the co-culture conditions of C. vulgaris and bioflocculant-producing bacteria in synthetic wastewater using response surface methodology (RSM), thus aiming to enhance C. vulgaris harvesting and lipid content. Three significant process variables- inoculation ratio of bacteria and microalgae, initial glucose concentration, and co-culture time- were proposed in the RSM model. F-values (3·98/8·46) and R(2) values (0·7817/0·8711) both indicated a reasonable prediction by the RSM model. The results showed that C. vulgaris harvesting efficiency reached 45·0-50·0%, and the lipid content was over 21·0% when co-cultured with bioflocculant-producing bacteria under the optimized culture conditions of inoculation ratio of bacteria and microalgae of 0·20-0·25, initial glucose concentration of <1·5 kg m(-3) and co-culture time of 9-14 days. This work provided new insights into microalgae harvesting and cost-effective microalgal bioproducts, and confirmed the promising prospect of introducing bioflocculant-producing bacteria into microalgae bioenergy production. This work optimized the co-culture conditions of microalgae (C. vulgaris) and bioflocculant-producing bacteria (F2, Rhizobium radiobacter) in synthetic wastewater using response surface methodology, aiming to enhance C. vulgaris harvesting and lipid produced content. Bioflocculant-producing microbes are environmentally friendly functional materials. They avoid the negative effects of traditional chemical flocculants. This work provided new insights into microalgae harvesting and cost-effective production of microalgal bioproducts, and confirmed the promising prospect of introducing bioflocculant-producing bacteria into microalgae bioenergy production. © 2015 The Society for Applied Microbiology.

Cultivation Of Microalgae (Chlorella vulgaris) For Biodiesel Production

NASA Astrophysics Data System (ADS)

Blinová, Lenka; Bartošová, Alica; Gerulová, Kristína

2015-06-01

Production of biofuel from renewable sources is considered to be one of the most sustainable alternatives to petroleum sourced fuels. Biofuels are also viable means of environmental and economic sustainability. Biofuels are divided into four generations, depending on the type of biomass used for biofuels production. At present, microalgae are presented as an ideal third generation biofuel feedstock because of their rapid growth rate. They also do not compete with food or feed crops, and can be produced on non-arable land. Cultivation conditions (temperature, pH, light, nutrient quantity and quality, salinity, aerating) are the major factors that influence photosynthesis activity and behaviour of the microalgae growth rate. In this paper, we present an overview about the effect of cultivation conditions on microalgae growth.

Improved photobio-H2 production regulated by artificial miRNA targeting psbA in green microalga Chlamydomonas reinhardtii.

PubMed

Li, Hui; Liu, Yanmei; Wang, Yuting; Chen, Meirong; Zhuang, Xiaoshan; Wang, Chaogang; Wang, Jiangxin; Hu, Zhangli

2018-01-01

Sulfur-deprived cultivation of Chlamydomonas reinhardtii , referred as "two-stage culture" transferring the cells from regular algal medium to sulfur-deplete one, has been extensively studied to improve photobio-H 2 production in this green microalga. During sulfur-deprivation treatment, the synthesis of a key component of photosystem II complex, D1 protein, was inhibited and improved photobio-H 2 production could be established in C. reinhardtii . However, separation of algal cells from a regular liquid culture medium to a sulfur-deprived one is not only a discontinuous process, but also a cost- and time-consuming operation. More applicable and economic alternatives for sustained H 2 production by C. reinhardtii are still highly required. In the present study, a significant improvement in photobio-H 2 production was observed in the transgenic green microalga C. reinhardtii , which employed a newly designed strategy based on a heat-inducible artificial miRNA (amiRNA) expression system targeting D1-encoded gene, psbA . A transgenic algal strain referred as "amiRNA-D1" has been successfully obtained by transforming the expression vector containing a heat-inducible promoter. After heat shock conducted in the same algal cultures, the expression of amiRNA-D1 was detected increased 15-fold accompanied with a 73% decrease of target gene psbA . More interestingly, this transgenic alga accumulated about 60% more H 2 content than the wild-type strain CC-849 at the end of 7-day cultivation. The photobio-H 2 production in the engineered transgenic alga was significantly improved. Without imposing any nutrient-deprived stress, this novel strategy provided a convenient and efficient way for regulation of photobio-H 2 production in green microalga by simply "turn on" the expression of a designed amiRNA.

Biodiesel Production by the Green Microalga Scenedesmus obliquus in a Recirculatory Aquaculture System

PubMed Central

Mandal, Shovon

2012-01-01

Biodiesel production was examined with Scenedesmus obliquus in a recirculatory aquaculture system with fish pond discharge and poultry litter to couple with waste treatment. Lipid productivity of 14,400 liter ha−1 year−1 was projected with 11 cultivation cycles per year. The fuel properties of the biodiesel produced adhered to Indian and international standards. PMID:22660702

Integration of microalgae cultivation with industrial waste remediation for biofuel and bioenergy production: opportunities and limitations.

PubMed

McGinn, Patrick J; Dickinson, Kathryn E; Bhatti, Shabana; Frigon, Jean-Claude; Guiot, Serge R; O'Leary, Stephen J B

2011-09-01

There is currently a renewed interest in developing microalgae as a source of renewable energy and fuel. Microalgae hold great potential as a source of biomass for the production of energy and fungible liquid transportation fuels. However, the technologies required for large-scale cultivation, processing, and conversion of microalgal biomass to energy products are underdeveloped. Microalgae offer several advantages over traditional 'first-generation' biofuels crops like corn: these include superior biomass productivity, the ability to grow on poor-quality land unsuitable for agriculture, and the potential for sustainable growth by extracting macro- and micronutrients from wastewater and industrial flue-stack emissions. Integrating microalgal cultivation with municipal wastewater treatment and industrial CO(2) emissions from coal-fired power plants is a potential strategy to produce large quantities of biomass, and represents an opportunity to develop, test, and optimize the necessary technologies to make microalgal biofuels more cost-effective and efficient. However, many constraints on the eventual deployment of this technology must be taken into consideration and mitigating strategies developed before large scale microalgal cultivation can become a reality. As a strategy for CO(2) biomitigation from industrial point source emitters, microalgal cultivation can be limited by the availability of land, light, and other nutrients like N and P. Effective removal of N and P from municipal wastewater is limited by the processing capacity of available microalgal cultivation systems. Strategies to mitigate against the constraints are discussed.

A Review on the Assessment of Stress Conditions for Simultaneous Production of Microalgal Lipids and Carotenoids

PubMed Central

Minhas, Amritpreet K.; Hodgson, Peter; Barrow, Colin J.; Adholeya, Alok

2016-01-01

Microalgal species are potential resource of both biofuels and high-value metabolites, and their production is growth dependent. Growth parameters can be screened for the selection of novel microalgal species that produce molecules of interest. In this context our review confirms that, autotrophic and heterotrophic organisms have demonstrated a dual potential, namely the ability to produce lipids as well as value-added products (particularly carotenoids) under influence of various physico-chemical stresses on microalgae. Some species of microalgae can synthesize, besides some pigments, very-long-chain polyunsaturated fatty acids (VL-PUFA,>20C) such as docosahexaenoic acid and eicosapentaenoic acid, those have significant applications in food and health. Producing value-added by-products in addition to biofuels, fatty acid methyl esters (FAME), and lipids has the potential to improve microalgae-based biorefineries by employing either the autotrophic or the heterotrophic mode, which could be an offshoot of biotechnology. The review considers the potential of microalgae to produce a range of products and indicates future directions for developing suitable criteria for choosing novel isolates through bioprospecting large gene pool of microalga obtained from various habitats and climatic conditions. PMID:27199903

Microalgal bioengineering for sustainable energy development: Recent transgenesis and metabolic engineering strategies.

PubMed

Banerjee, Chiranjib; Singh, Puneet Kumar; Shukla, Pratyoosh

2016-03-01

Exploring the efficiency of algae to produce remarkable products can be directly benefitted by studying its mechanism at systems level. Recent advents in biotechnology like flux balance analysis (FBA), genomics and in silico proteomics minimize the wet lab exertion. It is understood that FBA predicts the metabolic products, metabolic pathways and alternative pathway to maximize the desired product, and these are key components for microalgae bio-engineering. This review encompasses recent transgenesis techniques and metabolic engineering strategies applied to different microalgae for improving different traits. Further it also throws light on RNAi and riboswitch engineering based methods which may be advantageous for high throughput microalgal research. A valid and optimally designed microalga can be developed where every engineering strategies meet each other successfully and will definitely fulfill the market needs. It is also to be noted that Omics (viz. genetic and metabolic manipulation with bioinformatics) should be integrated to develop a strain which could prove to be a futuristic solution for sustainable development for energy. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microalgae as multi-functional options in modern agriculture: current trends, prospects and challenges.

PubMed

Renuka, Nirmal; Guldhe, Abhishek; Prasanna, Radha; Singh, Poonam; Bux, Faizal

Algae are a group of ubiquitous photosynthetic organisms comprising eukaryotic green algae and Gram-negative prokaryotic cyanobacteria, which have immense potential as a bioresource for various industries related to biofuels, pharmaceuticals, nutraceuticals and feed. This fascinating group of organisms also has applications in modern agriculture through facilitating increased nutrient availability, maintaining the organic carbon and fertility of soil, and enhancing plant growth and crop yields, as a result of stimulation of soil microbial activity. Several cyanobacteria provide nitrogen fertilization through biological nitrogen fixation and through enzymatic activities related to interconversions and mobilization of different forms of nitrogen. Both green algae and cyanobacteria are involved in the production of metabolites such as growth hormones, polysaccharides, antimicrobial compounds, etc., which play an important role in the colonization of plants and proliferation of microbial and eukaryotic communities in soil. Currently, the development of consortia of cyanobacteria with bacteria or fungi or microalgae or their biofilms has widened their scope of utilization. Development of integrated wastewater treatment and biomass production systems is an emerging technology, which exploits the nutrient sequestering potential of microalgae and its valorisation. This review focuses on prospects and challenges of application of microalgae in various areas of agriculture, including crop production, protection and natural resource management. An overview of the recent advances, novel technologies developed, their commercialization status and future directions are also included. Copyright © 2018 Elsevier Inc. All rights reserved.

Bioprospecting for hyper-lipid producing microalgal strains for sustainable biofuel production.

PubMed

Mutanda, T; Ramesh, D; Karthikeyan, S; Kumari, S; Anandraj, A; Bux, F

2011-01-01

Global petroleum reserves are shrinking at a fast pace, increasing the demand for alternate fuels. Microalgae have the ability to grow rapidly, and synthesize and accumulate large amounts (approximately 20-50% of dry weight) of neutral lipid stored in cytosolic lipid bodies. A successful and economically viable algae based biofuel industry mainly depends on the selection of appropriate algal strains. The main focus of bioprospecting for microalgae is to identify unique high lipid producing microalgae from different habitats. Indigenous species of microalgae with high lipid yields are especially valuable in the biofuel industry. Isolation, purification and identification of natural microalgal assemblages using conventional techniques is generally time consuming. However, the recent use of micromanipulation as a rapid isolating tool allows for a higher screening throughput. The appropriate media and growth conditions are also important for successful microalgal proliferation. Environmental parameters recorded at the sampling site are necessary to optimize in vitro growth. Identification of species generally requires a combination of morphological and genetic characterization. The selected microalgal strains are grown in upscale systems such as raceway ponds or photobireactors for biomass and lipid production. This paper reviews the recent methodologies adopted for site selection, sampling, strain selection and identification, optimization of cultural conditions for superior lipid yield for biofuel production. Energy generation routes of microalgal lipids and biomass are discussed in detail. Copyright © 2010 Elsevier Ltd. All rights reserved.

CO2 controlled flocculation of microalgae using pH responsive cellulose nanocrystals

NASA Astrophysics Data System (ADS)

Eyley, Samuel; Vandamme, Dries; Lama, Sanjaya; van den Mooter, Guy; Muylaert, Koenraad; Thielemans, Wim

2015-08-01

Cellulose nanocrystals were grafted with imidazole functionalities up to DS 0.06 using a one-pot functionalization strategy. The resulting nanocrystals were shown to have a pH responsive surface charge which was found to be positive below pH 6 and negative above pH 7. These imidazolyl cellulose nanocrystals were tested for flocculation of Chlorella vulgaris using CO2 to induce flocculation. Up to 90% flocculation efficiency was achieved with 200 mg L-1 dose. Furthermore, the modified cellulose nanocrystals showed good compatibility with the microalgae during cultivation, giving potential for the production of reversible flocculation systems.Cellulose nanocrystals were grafted with imidazole functionalities up to DS 0.06 using a one-pot functionalization strategy. The resulting nanocrystals were shown to have a pH responsive surface charge which was found to be positive below pH 6 and negative above pH 7. These imidazolyl cellulose nanocrystals were tested for flocculation of Chlorella vulgaris using CO2 to induce flocculation. Up to 90% flocculation efficiency was achieved with 200 mg L-1 dose. Furthermore, the modified cellulose nanocrystals showed good compatibility with the microalgae during cultivation, giving potential for the production of reversible flocculation systems. Electronic supplementary information (ESI) available: Spectra for all products. See DOI: 10.1039/C5NR03853G

Culture modes and financial evaluation of two oleaginous microalgae for biodiesel production in desert area with open raceway pond.

PubMed

He, Qiaoning; Yang, Haijian; Hu, Chunxiang

2016-10-01

Cultivation modes of autotrophic microalgae for biodiesel production utilizing open raceway pond were analyzed in this study. Five before screened good microalgae were tested their lipid productivity and biodiesel quality again in outdoor 1000L ORP. Then, Chlorella sp. L1 and Monoraphidium dybowskii Y2 were selected due to their stronger environmental adaptability, higher lipid productivity and better biodiesel properties. Further scale up cultivation for two species with batch and semi-continuous culture was conducted. In 40,000L ORP, higher lipid productivity (5.15 versus 4.06gm(-2)d(-1) for Chlorella sp. L1, 5.35 versus 3.00gm(-2)d(-1) for M. dybowskii Y2) was achieved in semi-continuous mode. Moreover, the financial costs of 14.18$gal(-1) and 13.31$gal(-1) for crude biodiesel in two microalgae with semi-continuous mode were more economically feasible for commercial production on large scale outdoors. Copyright © 2016 Elsevier Ltd. All rights reserved.

Palm oil mill effluent treatment and CO2 sequestration by using microalgae-sustainable strategies for environmental protection.

PubMed

Hariz, Harizah Bajunaid; Takriff, Mohd Sobri

2017-09-01

In this era of globalization, various products and technologies are being developed by the industries. While resources and energy are utilized from processes, wastes are being excreted through water streams, air, and ground. Without realizing it, environmental pollutions increase as the country develops. Effective technology is desired to create green factories that are able to overcome these issues. Wastewater is classified as the water coming from domestic or industrial sources. Wastewater treatment includes physical, chemical, and biological treatment processes. Aerobic and anaerobic processes are utilized in biological treatment approach. However, the current biological approaches emit greenhouse gases (GHGs), methane, and carbon dioxide that contribute to global warming. Microalgae can be the alternative to treating wastewater as it is able to consume nutrients from wastewater loading and fix CO 2 as it undergoes photosynthesis. The utilization of microalgae in the system will directly reduce GHG emissions with low operating cost within a short period of time. The aim of this review is to discuss the uses of native microalgae species in palm oil mill effluent (POME) and flue gas remediation. In addition, the discussion on the optimal microalgae cultivation parameter selection is included as this is significant for effective microalgae-based treatment operations.

High-value bioproducts from microalgae: strategies and progress.

PubMed

Liang, Ming-Hua; Zhu, Jianhua; Jiang, Jian-Guo

2018-04-20

Microalgae have been considered as alternative sustainable resources for high-value bioproducts such as lipids (especially triacylglycerides [TAGs]), polyunsaturated fatty acids (PUFAs), and carotenoids, due to their relatively high photosynthetic efficiency, no arable land requirement, and ease of scale-up. It is of great significance to exploit microalgae for the production of high-value bioproducts. How to improve the content or productivity of specific bioproducts has become one of the most urgent challenges. In this review, we will describe high-value bioproducts from microalgae and their biosynthetic pathways (mainly for lipids, PUFAs, and carotenoids). Recent progress and strategies for the enhanced production of bioproducts from microalgae are also described in detail, and these strategies take advantages of optimized cultivation conditions with abiotic stress, chemical stress (addition of metabolic precursors, phytohormones, chemical inhibitors, and chemicals inducing oxidative stress response), and molecular approaches such as metabolic engineering, transcriptional engineering, and gene disruption strategies (mainly RNAi, antisense RNA, miRNA-based knockdown, and CRISPR/Cas9).

Co-cultivation of microalgae in aquaponic systems.

PubMed

Addy, Min M; Kabir, Faryal; Zhang, Renchuan; Lu, Qian; Deng, Xiangyuan; Current, Dean; Griffith, Richard; Ma, Yiwei; Zhou, Wenguang; Chen, Paul; Ruan, Roger

2017-12-01

Aquaponics is a sustainable system for the future farming. In aquaponic systems, the nutrient-rich wastewater generated by the fish provides nutrients needed for vegetable growth. In the present study, the role of microalgae of Chlorella sp. in the floating-raft aquaponic system was evaluated for ammonia control. The yields of algal biomass, vegetable, and removal of the key nutrients from the systems were monitored during the operation of the aquaponic systems. When the systems were in full operation, the algae production was about 4.15±0.19g/m 2 ·day (dry basis) which is considered low because the growth conditions are primarily tailored to fish and vegetable production. However, it was found that algae had a positive effect on balancing pH drop caused by nitrifying bacteria, and the ammonia could be controlled by algae since algae prefer for ammonia nitrogen over nitrate nitrogen. The algae are more efficient for overall nitrogen removal than vegetables. Copyright © 2017 Elsevier Ltd. All rights reserved.

Carotenoids in Microalgae.

PubMed

Henríquez, Vitalia; Escobar, Carolina; Galarza, Janeth; Gimpel, Javier

Carotenoids are a class of isoprenoids synthesized by all photosynthetic organisms as well as by some non-photosynthetic bacteria and fungi with broad applications in food, feed and cosmetics, and also in the nutraceutical and pharmaceutical industries. Microalgae represent an important source of high-value products, which include carotenoids, among others. Carotenoids play key roles in light harvesting and energy transfer during photosynthesis and in the protection of the photosynthetic apparatus against photooxidative damage. Carotenoids are generally divided into carotenes and xanthophyls, but accumulation in microalgae can also be classified as primary (essential for survival) and secondary (by exposure to specific stimuli).In this chapter, we outline the high value carotenoids produced by commercially important microalgae, their production pathways, the improved production rates that can be achieved by genetic engineering as well as their biotechnological applications.

Placing microalgae on the biofuels priority list: a review of the technological challenges

PubMed Central

Greenwell, H. C.; Laurens, L. M. L.; Shields, R. J.; Lovitt, R. W.; Flynn, K. J.

2010-01-01

Microalgae provide various potential advantages for biofuel production when compared with ‘traditional’ crops. Specifically, large-scale microalgal culture need not compete for arable land, while in theory their productivity is greater. In consequence, there has been resurgence in interest and a proliferation of algae fuel projects. However, while on a theoretical basis, microalgae may produce between 10- and 100-fold more oil per acre, such capacities have not been validated on a commercial scale. We critically review current designs of algal culture facilities, including photobioreactors and open ponds, with regards to photosynthetic productivity and associated biomass and oil production and include an analysis of alternative approaches using models, balancing space needs, productivity and biomass concentrations, together with nutrient requirements. In the light of the current interest in synthetic genomics and genetic modifications, we also evaluate the options for potential metabolic engineering of the lipid biosynthesis pathways of microalgae. We conclude that although significant literature exists on microalgal growth and biochemistry, significantly more work needs to be undertaken to understand and potentially manipulate algal lipid metabolism. Furthermore, with regards to chemical upgrading of algal lipids and biomass, we describe alternative fuel synthesis routes, and discuss and evaluate the application of catalysts traditionally used for plant oils. Simulations that incorporate financial elements, along with fluid dynamics and algae growth models, are likely to be increasingly useful for predicting reactor design efficiency and life cycle analysis to determine the viability of the various options for large-scale culture. The greatest potential for cost reduction and increased yields most probably lies within closed or hybrid closed–open production systems. PMID:20031983

Use of orange peel extract for mixotrophic cultivation of Chlorella vulgaris: increased production of biomass and FAMEs.

PubMed

Park, Won-Kun; Moon, Myounghoon; Kwak, Min-Su; Jeon, Seungjib; Choi, Gang-Guk; Yang, Ji-Won; Lee, Bongsoo

2014-11-01

Mass cultivation of microalgae is necessary to achieve economically feasible production of microalgal biodiesel, but the high cost of nutrients is a major limitation. In this study, orange peel extract (OPE) was used as an inorganic and organic nutrient source for the cultivation of Chlorella vulgaris OW-01. Chemical composition analysis of the OPE indicated that it contains sufficient nutrients for mixotrophic cultivation of C. vulgaris OW-01. Analysis of biomass and FAME production showed that microalgae grown in OPE medium produced 3.4-times more biomass and 4.5-times more fatty acid methyl esters (FAMEs) than cells cultured in glucose-supplemented BG 11 medium (BG-G). These results suggest that growth of microalgae in an OPE-supplemented medium increases lipid production and that OPE has potential for use in the mass cultivation of microalgae. Copyright © 2014 Elsevier Ltd. All rights reserved.

Life-cycle analysis on biodiesel production from microalgae: water footprint and nutrients balance.

PubMed

Yang, Jia; Xu, Ming; Zhang, Xuezhi; Hu, Qiang; Sommerfeld, Milton; Chen, Yongsheng

2011-01-01

This research examines the life-cycle water and nutrients usage of microalgae-based biodiesel production. The influence of water types, operation with and without recycling, algal species, geographic distributions are analyzed. The results confirm the competitiveness of microalgae-based biofuels and highlight the necessity of recycling harvested water and using sea/wastewater as water source. To generate 1 kg biodiesel, 3726 kg water, 0.33 kg nitrogen, and 0.71 kg phosphate are required if freshwater used without recycling. Recycling harvest water reduces the water and nutrients usage by 84% and 55%. Using sea/wastewater decreases 90% water requirement and eliminates the need of all the nutrients except phosphate. The variation in microalgae species and geographic distribution are analyzed to reflect microalgae biofuel development in the US. The impacts of current federal and state renewable energy programs are also discussed to suggest suitable microalgae biofuel implementation pathways and identify potential bottlenecks. Copyright © 2010 Elsevier Ltd. All rights reserved.

The role of biochemical engineering in the production of biofuels from microalgae.

PubMed

Costa, Jorge Alberto Vieira; de Morais, Michele Greque

2011-01-01

Environmental changes that have occurred due to the use of fossil fuels have driven the search for alternative sources that have a lower environmental impact. First-generation biofuels were derived from crops such as sugar cane, corn and soybean, which contribute to water scarcity and deforestation. Second-generation biofuels originated from lignocellulose agriculture and forest residues, however these needed large areas of land that could be used for food production. Based on technology projections, the third generation of biofuels will be derived from microalgae. Microalgae are considered to be an alternative energy source without the drawbacks of the first- and second-generation biofuels. Depending upon the growing conditions, microalgae can produce biocompounds that are easily converted into biofuels. The biofuels from microalgae are an alternative that can keep the development of human activity in harmony with the environment. This study aimed to present the main biofuels that can be derived from microalgae. Copyright © 2010 Elsevier Ltd. All rights reserved.

Effective cultivation of microalgae for biofuel production: a pilot-scale evaluation of a novel oleaginous microalga Graesiella sp. WBG-1.

PubMed

Wen, Xiaobin; Du, Kui; Wang, Zhongjie; Peng, Xinan; Luo, Liming; Tao, Huanping; Xu, Yan; Zhang, Dan; Geng, Yahong; Li, Yeguang

2016-01-01

Commercial production of microalgal biodiesel is not yet economically viable, largely because of low storage lipid yield in microalgae mass cultivation. Selection of lipid-rich microalgae, thus, becomes one of the key research topics for microalgal biodiesel production. However, the laboratory screening protocols alone cannot predict the ability of the strains to dominate and perform in outdoor ponds. Comprehensive assessment of microalgae species should be performed not only under the laboratory conditions, but also in the fields. Laboratory investigations using a bubbled column photobioreactor indicated the microalga Graesiella sp. WBG-1 to be the most productive species among the 63 Chlorophyta strains. In a 10 L reactor, mimicking the industrial circular pond, Graesiella sp. WBG-1 produced 12.03 g biomass m(-2) day(-1) and 5.44 g lipids (45.23 % DW) m(-2) day(-1) under 15 mol m(-2) day(-1) artificial light irradiations. The lipid content decreased to ~34 % DW when the microalga was cultured in 30 L tank PBR under natural solar irradiations, but the decline of lipid content with scaling up was the minimum among the tested strains. Based on these results, the microalga was further tested for its lipid production and culture competitiveness using a pilot-scale raceway pond (200 m(2) illuminated area, culture volume 40,000 L). Consequently, Graesiella sp. WBG-1 maintained a high lipid content (33.4 % DW), of which ~90 % was storage TAGs. Results from the outdoor experiments indicated the nice adaptability of the Graesiella sp. WBG-1 to strong and fluctuating natural solar irradiance and temperature, and also demonstrated several other features, such as large cell size (easy for harvest and resistant to swallow by protozoa) and tolerance to high culture pH (helpful to CO2 fixation). Graesiella sp. WBG-1 was a promising strain capable of accumulating large amount of storage lipid under nature solar irradiance and temperature. The high lipid content of 33.4 % DW was achieved for the first time in pilot-scale raceway pond. The results also provide evidence for the feasibility of using low-cost raceway pond for autotrophic cultivation of microalgae for biodiesel production.

Carbon dioxide capture strategies from flue gas using microalgae: a review.

PubMed

Thomas, Daniya M; Mechery, Jerry; Paulose, Sylas V

2016-09-01

Global warming and pollution are the twin crises experienced globally. Biological offset of these crises are gaining importance because of its zero waste production and the ability of the organisms to thrive under extreme or polluted condition. In this context, this review highlights the recent developments in carbon dioxide (CO2) capture from flue gas using microalgae and finding the best microalgal remediation strategy through contrast and comparison of different strategies. Different flue gas microalgal remediation strategies discussed are as follows: (i) Flue gas to CO2 gas segregation using adsorbents for microalgal mitigation, (ii) CO2 separation from flue gas using absorbents and later regeneration for microalgal mitigation, (iii) Flue gas to liquid conversion for direct microalgal mitigation, and (iv) direct flue gas mitigation using microalgae. This work also studies the economic feasibility of microalgal production. The study discloses that the direct convening of flue gas with high carbon dioxide content, into microalgal system is cost-effective.

Biological potential of microalgae in China for biorefinery-based production of biofuels and high value compounds.

PubMed

Li, Jingjing; Liu, Ying; Cheng, Jay J; Mos, Michal; Daroch, Maurycy

2015-12-25

Microalgae abundance and diversity in China shows promise for identifying suitable strains for developing algal biorefinery. Numerous strains of microalgae have already been assessed as feedstocks for bioethanol and biodiesel production, but commercial scale algal biofuel production is yet to be demonstrated, most likely due to huge energy costs associated with algae cultivation, harvesting and processing. Biorefining, integrated processes for the conversion of biomass into a variety of products, can improve the prospects of microalgal biofuels by combining them with the production of high value co-products. Numerous microalgal strains in China have been identified as producers of various high value by-products with wide application in the medicine, food, and cosmetics industries. This paper reviews microalgae resources in China and their potential in producing liquid biofuels (bioethanol and biodiesel) and high value products in an integrated biorefinery approach. Implementation of a 'high value product first' principle should make the integrated process of fuels and chemicals production economically feasible and will ensure that public and private interest in the development of microalgal biotechnology is maintained. Copyright © 2015 Elsevier B.V. All rights reserved.

The synergistic effects for the co-cultivation of oleaginous yeast-Rhodotorula glutinis and microalgae-Scenedesmus obliquus on the biomass and total lipids accumulation.

PubMed

Yen, Hong-Wei; Chen, Pin-Wen; Chen, Li-Juan

2015-05-01

In this co-culture of oleaginous yeast-Rhodotorula glutinis and microalgae-Scenedesmus obliquus, microalgae potentially acts as an oxygen generator for the growth of aerobic yeast while the yeast mutually provides CO2 to the microalgae as both carry out the production of lipids. To explore the synergistic effects of co-cultivation on the cells growth and total lipids accumulation, several co-culture process parameters including the carbon source concentration, temperature and dissolved oxygen level would be firstly investigated in the flask trials. The results of co-culture in a 5L photobioreactor revealed that about 40-50% of biomass increased and 60-70% of total lipid increased was observed as compared to the single culture batches. Besides the synergistic effects of gas utilization, the providing of trace elements to each other after the natural cells lysis was believed to be another benefit to the growth of the overall co-culture system. Copyright © 2014 Elsevier Ltd. All rights reserved.

An integrated assessment of location-dependent scaling for microalgae biofuel production facilities

DOE PAGES

Coleman, André M.; Abodeely, Jared M.; Skaggs, Richard L.; ...

2014-06-19

Successful development of a large-scale microalgae-based biofuels industry requires comprehensive analysis and understanding of the feedstock supply chain—from facility siting and design through processing and upgrading of the feedstock to a fuel product. The evolution from pilot-scale production facilities to energy-scale operations presents many multi-disciplinary challenges, including a sustainable supply of water and nutrients, operational and infrastructure logistics, and economic competitiveness with petroleum-based fuels. These challenges are partially addressed by applying the Integrated Assessment Framework (IAF) – an integrated multi-scale modeling, analysis, and data management suite – to address key issues in developing and operating an open-pond microalgae production facility.more » This is done by analyzing how variability and uncertainty over space and through time affect feedstock production rates, and determining the site-specific “optimum” facility scale to minimize capital and operational expenses. This approach explicitly and systematically assesses the interdependence of biofuel production potential, associated resource requirements, and production system design trade-offs. To provide a baseline analysis, the IAF was applied in this paper to a set of sites in the southeastern U.S. with the potential to cumulatively produce 5 billion gallons per year. Finally, the results indicate costs can be reduced by scaling downstream processing capabilities to fit site-specific growing conditions, available and economically viable resources, and specific microalgal strains.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

T. Nakamura; C.L. Senior

Most of the anthropogenic emissions of carbon dioxide result from the combustion of fossil fuels for energy production. Photosynthesis has long been recognized as a means, at least in theory, to sequester anthropogenic carbon dioxide. Aquatic microalgae have been identified as fast growing species whose carbon fixing rates are higher than those of land-based plants by one order of magnitude. Physical Sciences Inc. (PSI), Aquasearch, and the Hawaii Natural Energy Institute at the University of Hawaii are jointly developing technologies for recovery and sequestration of CO{sub 2} from stationary combustion systems by photosynthesis of microalgae. The research is aimed primarilymore » at demonstrating the ability of selected species of microalgae to effectively fix carbon from typical power plant exhaust gases. This report covers the reporting period 1 October 2000 to 31 March 2005 in which PSI, Aquasearch and University of Hawaii conducted their tasks. This report discusses results of the work pertaining to five tasks: Task 1--Supply of CO2 from Power Plant Flue Gas to Photobioreactor; Task 2--Selection of Microalgae; Task 3--Optimization and Demonstration of Industrial Scale Photobioreactor; Task 4--Carbon Sequestration System Design; and Task 5--Economic Analysis. Based on the work conducted in each task summary conclusion is presented.« less

An outlook on microalgal biofuels.

PubMed

Wijffels, René H; Barbosa, Maria J

2010-08-13

Microalgae are considered one of the most promising feedstocks for biofuels. The productivity of these photosynthetic microorganisms in converting carbon dioxide into carbon-rich lipids, only a step or two away from biodiesel, greatly exceeds that of agricultural oleaginous crops, without competing for arable land. Worldwide, research and demonstration programs are being carried out to develop the technology needed to expand algal lipid production from a craft to a major industrial process. Although microalgae are not yet produced at large scale for bulk applications, recent advances-particularly in the methods of systems biology, genetic engineering, and biorefining-present opportunities to develop this process in a sustainable and economical way within the next 10 to 15 years.

Biodiesel production from wet microalgae feedstock using sequential wet extraction/transesterification and direct transesterification processes.

PubMed

Chen, Ching-Lung; Huang, Chien-Chang; Ho, Kao-Chia; Hsiao, Ping-Xuan; Wu, Meng-Shan; Chang, Jo-Shu

2015-10-01

Although producing biodiesel from microalgae seems promising, there is still a lack of technology for the quick and cost-effective conversion of biodiesel from wet microalgae. This study was aimed to develop a novel microalgal biodiesel producing method, consisting of an open system of microwave disruption, partial dewatering (via combination of methanol treatment and low-speed centrifugation), oil extraction, and transesterification without the pre-removal of the co-solvent, using Chlamydomonas sp. JSC4 with 68.7 wt% water content as the feedstock. Direct transesterification with the disrupted wet microalgae was also conducted. The biomass content of the wet microalgae increased to 56.6 and 60.5 wt%, respectively, after microwave disruption and partial dewatering. About 96.2% oil recovery was achieved under the conditions of: extraction temperature, 45°C; hexane/methanol ratio, 3:1; extraction time, 80 min. Transesterification of the extracted oil reached 97.2% conversion within 15 min at 45°C and 6:1 solvent/methanol ratio with simultaneous Chlorophyll removal during the process. Nearly 100% biodiesel conversion was also obtained while conducting direct transesterification of the disrupted oil-bearing microalgal biomass. Copyright © 2015 Elsevier Ltd. All rights reserved.

In situ Transesterification of Microalgal Oil to Produce Algal Biodiesel

DOT National Transportation Integrated Search

2012-06-01

This research was to process whole microalgae cells for biodiesel production without first extracting lipids. The ultimate : goal is develop a novel process for algal biodiesel production directly from microalgae cells in a single step, i.e., in situ...

Analysis of Economic and Environmental Aspects of Microalgae Biorefinery for Biofuels Production: A Review.

PubMed

Chia, Shir Reen; Chew, Kit Wayne; Show, Pau Loke; Yap, Yee Jiun; Ong, Hwai Chyuan; Ling, Tau Chuan; Chang, Jo-Shu

2018-06-01

Microalgae are considered promising feedstock for the production of biofuels and other bioactive compounds, yet there are still challenges on commercial applications of microalgae-based products. This review focuses on the economic analysis, environmental impact, and industrial potential of biofuels production from microalgae. The cost of biofuels production remains higher compared to conventional fuel sources. However, integration of biorefinery pathways with biofuels production for the recovery of value-added products (such as antioxidants, natural dyes, cosmetics, nutritional supplements, polyunsaturated fatty acids, and so forth) could substantially reduce the production costs. It also paves the way for sustainable energy resources by significantly reducing the emissions of CO 2 , NO x , SO x , and heavy metals. Large-scale biofuels production has yet to be successfully commercialized with many roadblocks ahead and heavy competition with conventional fuel feedstock as well as technological aspects. One of the prominent challenges is to develop a cost-effective method to achieve high-density microalgal cultivation on an industrial scale. The biofuels industry should be boosted by Government's support in the form of subsidies and incentives, for addressing the pressing climate change issues, achieving sustainability, and energy security. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrocarbon productivities in different Botryococcus strains: comparative methods in product quantification.

PubMed

Eroglu, Ela; Okada, Shigeru; Melis, Anastasios

2011-08-01

Six different strains of the green microalgae Botryococcus belonging to the A-race or B-race, accumulating alkadiene or botryococcene hydrocarbons, respectively, were compared for biomass and hydrocarbon productivities. Biomass productivity was assessed gravimetrically upon strain growth in the laboratory under defined conditions. Hydrocarbon productivities were measured by three different and independent experimental approaches, including density equilibrium of the intact cells and micro-colonies, spectrophotometric analysis of hydrocarbon extracts, and gravimetric quantitation of eluted hydrocarbons. All three hydrocarbon-quantitation methods yielded similar results for each of the strains examined. The B-race microalgae Botryococcus braunii var. Showa and Kawaguchi-1 constitutively accumulated botryococcene hydrocarbons equivalent to 30% and 20%, respectively, of their overall biomass. The A-race microalgae Botryococcus braunii, varieties Yamanaka, UTEX 2441 and UTEX LB572 constitutively accumulated alkadiene hydrocarbons ranging from 14% to 13% and 10% of their overall biomass, respectively. Botryococcus sudeticus (UTEX 2629), a morphologically different green microalga, had the lowest hydrocarbon accumulation, equal to about 3% of its overall biomass. Results validate the density equilibrium and spectrophotometric analysis methods in the quantitation of botryococcene-type hydrocarbons. These analytical advances will serve in the screening and selection of B. braunii and of other microalgae in efforts to identify those having a high hydrocarbon content for use in commercial applications.

Anaerobic digestion of microalgal biomass: Challenges, opportunities and research needs.

PubMed

Gonzalez-Fernandez, Cristina; Sialve, Bruno; Molinuevo-Salces, Beatriz

2015-12-01

Integration of anaerobic digestion (AD) with microalgae processes has become a key topic to support economic and environmental development of this resource. Compared with other substrates, microalgae can be produced close to the plant without the need for arable lands and be fully integrated within a biorefinery. As a limiting step, anaerobic hydrolysis appears to be one of the most challenging steps to reach a positive economic balance and to completely exploit the potential of microalgae for biogas and fertilizers production. This review covers recent investigations dealing with microalgae AD and highlights research opportunities and needs to support the development of this resource. Novel approaches to increase hydrolysis rate, the importance of the reactor design and the noteworthiness of the microbial anaerobic community are addressed. Finally, the integration of AD with microalgae processes and the potential of the carboxylate platform for chemicals and biofuels production are reviewed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Cultivation and energy efficient harvesting of microalgae using thermoreversible sol-gel transition

PubMed Central

Estime, Bendy; Ren, Dacheng; Sureshkumar, Radhakrishna

2017-01-01

Microalgae represent a promising source of renewable biomass for the production of biofuels and valuable chemicals. However, energy efficient cultivation and harvesting technologies are necessary to improve economic viability. A Tris-Acetate-Phosphate-Pluronic (TAPP) medium that undergoes a thermoreversible sol-gel transition is developed to efficiently culture and harvest microalgae without affecting the productivity as compared to that in traditional culture in a well-mixed suspension. After seeding microalgae in the TAPP medium in a solution phase at 15 °C, the temperature is increased by 7 °C to induce gelation. Within the gel, microalgae are observed to grow in large clusters rather than as isolated cells. The settling velocity of the microalgal clusters is approximately ten times larger than that of individual cells cultured in typical solution media. Such clusters are easily harvested gravimetrically by decreasing the temperature to bring the medium to a solution phase. PMID:28102313

An assessment of the economic aspects of CO2 sequestration in a route for biodiesel production from microalgae.

PubMed

Soares, Fabio Rubens; Martins, Gilberto; Seo, Emília Satoshi Miyamaru

2013-01-01

Photosynthetic microalgae are unicellular organisms that, during their cultivation, can fix carbon dioxide efficiently from various sources, including the air and exhaust gases from industrial processes. This feature can lead to economic benefits in the production process of biodiesel by way of the clean development mechanism, for which carbon credits for environmental benefits may be granted and which will contribute towards reducing costs in the production process. This study seeks to quantify the contribution of carbon credits in the operating costs of a route for biodiesel production from microalgae, as proposed by Davis et al. [Techno-economic analysis ofautotrophic microalgae for fuel production. Appl Energy. 2011; 88:3524-3531]. The results showed a reduction in annual operating costs by around 5%. This figure may be conservative, since the production process considered can be further improved to reduce operating costs and thus increase the contribution margin of carbon credits, which will reduce costs. On the other hand, the price of carbon may also rise in the future, thereby increasing its contribution towards a reduction in operating costs.

Microalgae Nutraceuticals.

PubMed

Nicoletti, Marcello

2016-08-22

Among the new entries in the food supplements sector, an important place must be assigned to nutraceuticals containing microalgae, nowadays accounting for a large and rapidly expanding market. The marketed products are mainly based on three production strains, i.e., Spirulina and Chlorella, followed at a distance by Klamath. It is a composite situation, since two of them are cyanobacteria and the second one is eukaryotic. The reality is that each presents similarities in shape and appearance concerning the marketed form and several utilizations, and peculiarities that need special attention and adequate studies. First, general information is reported about the current scientific knowledge on each microalga, in particular the nutritional value and properties in prevention and wellbeing. Second, original studies are presented concerning the quality control of marketed products. Quality control is a key argument in nutraceuticals validation. Microalgae are particular organisms that need specific approaches to confirm identity and validate properties. The proposed control of quality is based on microscopic analysis of the morphologic characteristics. The final parts of this paper are dedicated to the need for specificity in uses and claims and to considerations about the future of microalgae in food supplements.

Microalgae Nutraceuticals

PubMed Central

Nicoletti, Marcello

2016-01-01

Among the new entries in the food supplements sector, an important place must be assigned to nutraceuticals containing microalgae, nowadays accounting for a large and rapidly expanding market. The marketed products are mainly based on three production strains, i.e., Spirulina and Chlorella, followed at a distance by Klamath. It is a composite situation, since two of them are cyanobacteria and the second one is eukaryotic. The reality is that each presents similarities in shape and appearance concerning the marketed form and several utilizations, and peculiarities that need special attention and adequate studies. First, general information is reported about the current scientific knowledge on each microalga, in particular the nutritional value and properties in prevention and wellbeing. Second, original studies are presented concerning the quality control of marketed products. Quality control is a key argument in nutraceuticals validation. Microalgae are particular organisms that need specific approaches to confirm identity and validate properties. The proposed control of quality is based on microscopic analysis of the morphologic characteristics. The final parts of this paper are dedicated to the need for specificity in uses and claims and to considerations about the future of microalgae in food supplements. PMID:28231149

Coupling of Algal Biofuel Production with Wastewater

PubMed Central

Panwar, Amit; Bisht, Tara Singh; Tamta, Sushma

2014-01-01

Microalgae have gained enormous consideration from scientific community worldwide emerging as a viable feedstock for a renewable energy source virtually being carbon neutral, high lipid content, and comparatively more advantageous to other sources of biofuels. Although microalgae are seen as a valuable source in majority part of the world for production of biofuels and bioproducts, still they are unable to accomplish sustainable large-scale algal biofuel production. Wastewater has organic and inorganic supplements required for algal growth. The coupling of microalgae with wastewater is an effective way of waste remediation and a cost-effective microalgal biofuel production. In this review article, we will primarily discuss the possibilities and current scenario regarding coupling of microalgal cultivation with biofuel production emphasizing recent progress in this area. PMID:24982930

Microalgae-based advanced municipal wastewater treatment for reuse in water bodies.

PubMed

Wang, Jing-Han; Zhang, Tian-Yuan; Dao, Guo-Hua; Xu, Xue-Qiao; Wang, Xiao-Xiong; Hu, Hong -Ying

2017-04-01

Reuse of secondary municipal effluent from wastewater treatment plants in water bodies could effectively alleviate freshwater resource shortage. However, excessive nutrients must be efficiently removed to prevent eutrophication. Compared with other means of advanced wastewater treatment, microalgae-based processes display overwhelming advantages including efficient and simultaneous N and P removal, no requirement of additional chemicals, O 2 generation, CO 2 mitigation, and potential value-added products from harvested biomass. One particular challenge of microalgae-based advanced municipal wastewater treatment compared to treatment of other types of wastewater is that concentrations of nutrients and N:P ratios in secondary municipal effluent are much lower and imbalanced. Therefore, there should be comprehensive considerations on nutrient removal from this specific type of effluent. Removal of nutrients and organic substances, and other environmental benefits of microalgae-based advanced municipal wastewater treatment systems were summarized. Among the existing studies on microalgal advanced nutrient removal, much information on major parameters is absent, rendering performances between studies not really comparable. Mechanisms of microalgae-based nitrogen and phosphorus removal were respectively analyzed to better understand advanced nutrient removal from municipal secondary effluent. Factors influencing microalgae-based nutrient removal were divided into intrinsic, environmental, and operational categories; several factors were identified in each category, and their influences on microalgal nutrient removal were discussed. A multiplicative kinetic model was integrated to estimate microalgal growth-related nutrient removal based majorly on environmental and intrinsic factors. Limitations and prospects of future full-scale microalgae-based advanced municipal wastewater treatment were also suggested. The manuscript could offer much valuable information for future studies on microalgae-based advanced wastewater treatment and water reuse.

Superior triacylglycerol (TAG) accumulation in starchless mutants of Scenedesmus obliquus: (I) mutant generation and characterization

PubMed Central

2014-01-01

Background Microalgae are a promising platform for producing neutral lipids, to be used in the application for biofuels or commodities in the feed and food industry. A very promising candidate is the oleaginous green microalga Scenedesmus obliquus, because it accumulates up to 45% w/w triacylglycerol (TAG) under nitrogen starvation. Under these conditions, starch is accumulated as well. Starch can amount up to 38% w/w under nitrogen starvation, which is a substantial part of the total carbon captured. When aiming for optimized TAG production, blocking the formation of starch could potentially increase carbon allocation towards TAG. In an attempt to increase TAG content, productivity and yield, starchless mutants of this high potential strain were generated using UV mutagenesis. Previous studies in Chlamydomonas reinhardtii have shown that blocking the starch synthesis yields higher TAG contents, although these TAG contents do not surpass those of oleaginous microalgae yet. So far no starchless mutants in oleaginous green microalgae have been isolated that result in higher TAG productivities. Results Five starchless mutants have been isolated successfully from over 3,500 mutants. The effect of the mutation on biomass and total fatty acid (TFA) and TAG productivity under nitrogen-replete and nitrogen-depleted conditions was studied. All five starchless mutants showed a decreased or completely absent starch content. In parallel, an increased TAG accumulation rate was observed for the starchless mutants and no substantial decrease in biomass productivity was perceived. The most promising mutant showed an increase in TFA productivity of 41% at 4 days after nitrogen depletion, reached a TAG content of 49.4% (% of dry weight) and had no substantial change in biomass productivity compared to the wild type. Conclusions The improved S. obliquus TAG production strains are the first starchless mutants in an oleaginous green microalga that show enhanced TAG content under photoautotrophic conditions. These results can pave the way towards a more feasible microalgae-driven TAG production platform. PMID:24920957

Biochemical Characterization of Human Anti-Hepatitis B Monoclonal Antibody Produced in the Microalgae Phaeodactylum tricornutum.

PubMed

Vanier, Gaëtan; Hempel, Franziska; Chan, Philippe; Rodamer, Michael; Vaudry, David; Maier, Uwe G; Lerouge, Patrice; Bardor, Muriel

2015-01-01

Monoclonal antibodies (mAbs) represent actually the major class of biopharmaceuticals. They are produced recombinantly using living cells as biofactories. Among the different expression systems currently available, microalgae represent an emerging alternative which displays several biotechnological advantages. Indeed, microalgae are classified as generally recognized as safe organisms and can be grown easily in bioreactors with high growth rates similarly to CHO cells. Moreover, microalgae exhibit a phototrophic lifestyle involving low production costs as protein expression is fueled by photosynthesis. However, questions remain to be solved before any industrial production of algae-made biopharmaceuticals. Among them, protein heterogeneity as well as protein post-translational modifications need to be evaluated. Especially, N-glycosylation acquired by the secreted recombinant proteins is of major concern since most of the biopharmaceuticals including mAbs are N-glycosylated and it is well recognized that glycosylation represent one of their critical quality attribute. In this paper, we assess the quality of the first recombinant algae-made mAbs produced in the diatom, Phaeodactylum tricornutum. We are focusing on the characterization of their C- and N-terminal extremities, their signal peptide cleavage and their post-translational modifications including N-glycosylation macro- and microheterogeneity. This study brings understanding on diatom cellular biology, especially secretion and intracellular trafficking of proteins. Overall, it reinforces the positioning of P. tricornutum as an emerging host for the production of biopharmaceuticals and prove that P. tricornutum is suitable for producing recombinant proteins bearing high mannose-type N-glycans.

Investigation of biomass concentration, lipid production, and cellulose content in Chlorella vulgaris cultures using response surface methodology.

PubMed

Aguirre, Ana-Maria; Bassi, Amarjeet

2013-08-01

The microalgae Chlorella vulgaris produce lipids that after extraction from cells can be converted into biodiesel. However, these lipids cannot be efficiently extracted from cells due to the presence of the microalgae cell wall, which acts as a barrier for lipid removal when traditional extraction methods are employed. Therefore, a microalgae system with high lipid productivity and thinner cell walls could be more suitable for lipid production from microalgae. This study addresses the effect of culture conditions, specifically carbon dioxide and sodium nitrate concentrations, on biomass concentration and the ratio of lipid productivity/cellulose content. Optimization of culture conditions was done by response surface methodology. The empirical model for biomass concentration (R(2)  = 96.0%) led to a predicted maximum of 1123.2 mg dw L(-1) when carbon dioxide and sodium nitrate concentrations were 2.33% (v/v) and 5.77 mM, respectively. For lipid productivity/cellulose content ratio (R(2)  = 95.2%) the maximum predicted value was 0.46 (mg lipid L(-1)  day(-1) )(mg cellulose mg biomass(-1) )(-1) when carbon dioxide concentration was 4.02% (v/v) and sodium nitrate concentration was 3.21 mM. A common optimum point for both variables (biomass concentration and lipid productivity/cellulose content ratio) was also found, predicting a biomass concentration of 1119.7 mg dw L(-1) and lipid productivity/cellulose content ratio of 0.44 (mg lipid L(-1)  day(-1) )(mg cellulose mg biomass(-1) )(-1) for culture conditions of 3.77% (v/v) carbon dioxide and 4.01 mM sodium nitrate. The models were experimentally validated and results supported their accuracy. This study shows that it is possible to improve lipid productivity/cellulose content by manipulation of culture conditions, which may be applicable to any scale of bioreactors. Copyright © 2013 Wiley Periodicals, Inc.

Microalgae as a raw material for biofuels production.

PubMed

Gouveia, Luisa; Oliveira, Ana Cristina

2009-02-01

Biofuels demand is unquestionable in order to reduce gaseous emissions (fossil CO(2), nitrogen and sulfur oxides) and their purported greenhouse, climatic changes and global warming effects, to face the frequent oil supply crises, as a way to help non-fossil fuel producer countries to reduce energy dependence, contributing to security of supply, promoting environmental sustainability and meeting the EU target of at least of 10% biofuels in the transport sector by 2020. Biodiesel is usually produced from oleaginous crops, such as rapeseed, soybean, sunflower and palm. However, the use of microalgae can be a suitable alternative feedstock for next generation biofuels because certain species contain high amounts of oil, which could be extracted, processed and refined into transportation fuels, using currently available technology; they have fast growth rate, permit the use of non-arable land and non-potable water, use far less water and do not displace food crops cultures; their production is not seasonal and they can be harvested daily. The screening of microalgae (Chlorella vulgaris, Spirulina maxima, Nannochloropsis sp., Neochloris oleabundans, Scenedesmus obliquus and Dunaliella tertiolecta) was done in order to choose the best one(s), in terms of quantity and quality as oil source for biofuel production. Neochloris oleabundans (fresh water microalga) and Nannochloropsis sp. (marine microalga) proved to be suitable as raw materials for biofuel production, due to their high oil content (29.0 and 28.7%, respectively). Both microalgae, when grown under nitrogen shortage, show a great increase (approximately 50%) in oil quantity. If the purpose is to produce biodiesel only from one species, Scenedesmus obliquus presents the most adequate fatty acid profile, namely in terms of linolenic and other polyunsaturated fatty acids. However, the microalgae Neochloris oleabundans, Nannochloropsis sp. and Dunaliella tertiolecta can also be used if associated with other microalgal oils and/or vegetable oils.

Applications of microfluidics in microalgae biotechnology: A review.

PubMed

Juang, Yi-Je; Chang, Jo-Shu

2016-03-01

Microalgae have been one of the important sources for biofuel production owing to their competitive advantages such as no need to tap into the global food supply chain, higher energy density, and absorbing carbon dioxide to mitigate global warming. One of the key factors to ensure successful biofuel production is that it requires not only bioprospecting of the microalgae with high lipid content, high growth rate and tolerance to environmental parameters but also on-site monitoring of the cultivation process and optimization of the culturing conditions. However, as the conventional techniques usually involve in complicated procedures, or are time-consuming or labor intensive, microfluidics technology offers an attractive alternative to resolve these issues. In this review, applications of microfluidics to bioprospecting in microalgae biotechnology were discussed such as cell identification, cell sorting/screening, cell culturing and cell disruption. In addition, utilization of microalgae in micro-sized fuel cells and microfluidic platforms for biosensing was addressed. This review reports the recent studies and offers a look into how microfluidics is exploited to tackle the issues encountered in the microalgae biotechnology. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficient Anaerobic Digestion of Microalgae Biomass: Proteins as a Key Macromolecule.

PubMed

Magdalena, Jose Antonio; Ballesteros, Mercedes; González-Fernandez, Cristina

2018-05-06

Biogas generation is the least complex technology to transform microalgae biomass into bioenergy. Since hydrolysis has been pointed out as the rate limiting stage of anaerobic digestion, the main challenge for an efficient biogas production is the optimization of cell wall disruption/hydrolysis. Among all tested pretreatments, enzymatic treatments were demonstrated not only very effective in disruption/hydrolysis but they also revealed the impact of microalgae macromolecular composition in the anaerobic process. Although carbohydrates have been traditionally recognized as the polymers responsible for the low microalgae digestibility, protease addition resulted in the highest organic matter solubilization and the highest methane production. However, protein solubilization during the pretreatment can result in anaerobic digestion inhibition due to the release of large amounts of ammonium nitrogen. The possible solutions to overcome these negative effects include the reduction of protein biomass levels by culturing the microalgae in low nitrogen media and the use of ammonia tolerant anaerobic inocula. Overall, this review is intended to evidence the relevance of microalgae proteins in different stages of anaerobic digestion, namely hydrolysis and methanogenesis.

Microalgal biofactories: a promising approach towards sustainable omega-3 fatty acid production

PubMed Central

2012-01-01

Omega-3 fatty acids eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) provide significant health benefits and this has led to an increased consumption as dietary supplements. Omega-3 fatty acids EPA and DHA are found in animals, transgenic plants, fungi and many microorganisms but are typically extracted from fatty fish, putting additional pressures on global fish stocks. As primary producers, many marine microalgae are rich in EPA (C20:5) and DHA (C22:6) and present a promising source of omega-3 fatty acids. Several heterotrophic microalgae have been used as biofactories for omega-3 fatty acids commercially, but a strong interest in autotrophic microalgae has emerged in recent years as microalgae are being developed as biofuel crops. This paper provides an overview of microalgal biotechnology and production platforms for the development of omega-3 fatty acids EPA and DHA. It refers to implications in current biotechnological uses of microalgae as aquaculture feed and future biofuel crops and explores potential applications of metabolic engineering and selective breeding to accumulate large amounts of omega-3 fatty acids in autotrophic microalgae. PMID:22830315

Lipid for biodiesel production from attached growth Chlorella vulgaris biomass cultivating in fluidized bed bioreactor packed with polyurethane foam material.

PubMed

Mohd-Sahib, Ainur-Assyakirin; Lim, Jun-Wei; Lam, Man-Kee; Uemura, Yoshimitsu; Isa, Mohamed Hasnain; Ho, Chii-Dong; Kutty, Shamsul Rahman Mohamed; Wong, Chung-Yiin; Rosli, Siti-Suhailah

2017-09-01

The potential to grow attached microalgae Chlorella vulgaris in fluidized bed bioreactor was materialized in this study, targeting to ease the harvesting process prior to biodiesel production. The proposed thermodynamic mechanism and physical property assessment of various support materials verified polyurethane to be suitable material favouring the spontaneous adhesion by microalgae cells. The 1-L bioreactor packed with only 2.4% (v/v) of 1.00-mL polyurethane foam cubes could achieve the highest attached growth microalgae biomass and lipid weights of 812±122 and 376±37mg, respectively, in comparison with other cube sizes. The maturity of attached growth microalgae biomass for harvesting could also be determined from the growth trend of suspended microalgae biomass. Analysis of FAME composition revealed that the harvested microalgae biomass was dominated by C16-C18 (>60%) and mixture of saturated and mono-unsaturated fatty acids (>65%), satiating the biodiesel standard with adequate cold flow property and oxidative stability. Copyright © 2017 Elsevier Ltd. All rights reserved.

Manipulating environmental stresses and stress tolerance of microalgae for enhanced production of lipids and value-added products-A review.

PubMed

Chen, Bailing; Wan, Chun; Mehmood, Muhammad Aamer; Chang, Jo-Shu; Bai, Fengwu; Zhao, Xinqing

2017-11-01

Microalgae have promising potential to produce lipids and a variety of high-value chemicals. Suitable stress conditions such as nitrogen starvation and high salinity could stimulate synthesis and accumulation of lipids and high-value products by microalgae, therefore, various stress-modification strategies were developed to manipulate and optimize cultivation processes to enhance bioproduction efficiency. On the other hand, advancements in omics-based technologies have boosted the research to globally understand microalgal gene regulation under stress conditions, which enable further improvement of production efficiency via genetic engineering. Moreover, integration of multi-omics data, synthetic biology design, and genetic engineering manipulations exhibits a tremendous potential in the betterment of microalgal biorefinery. This review discusses the process manipulation strategies and omics studies on understanding the regulation of metabolite biosynthesis under various stressful conditions, and proposes genetic engineering of microalgae to improve bioproduction via manipulating stress tolerance. Copyright © 2017 Elsevier Ltd. All rights reserved.

LHCSR Expression under HSP70/RBCS2 Promoter as a Strategy to Increase Productivity in Microalgae.

PubMed

Perozeni, Federico; Stella, Giulio Rocco; Ballottari, Matteo

2018-01-05

Microalgae are unicellular photosynthetic organisms considered as potential alternative sources for biomass, biofuels or high value products. However, limited biomass productivity is commonly experienced in their cultivating system despite their high potential. One of the reasons for this limitation is the high thermal dissipation of the light absorbed by the outer layers of the cultures exposed to high light caused by the activation of a photoprotective mechanism called non-photochemical quenching (NPQ). In the model organism for green algae Chlamydomonas reinhardtii , NPQ is triggered by pigment binding proteins called light-harvesting-complexes-stress-related (LHCSRs), which are over-accumulated in high light. It was recently reported that biomass productivity can be increased both in microalgae and higher plants by properly tuning NPQ induction. In this work increased light use efficiency is reported by introducing in C. reinhardtii a LHCSR3 gene under the control of Heat Shock Protein 70 / RUBISCO small chain 2 promoter in a npq4 lhcsr1 background, a mutant strain knockout for all LHCSR genes. This complementation strategy leads to a low expression of LHCSR3 , causing a strong reduction of NPQ induction but is still capable of protecting from photodamage at high irradiance, resulting in an improved photosynthetic efficiency and higher biomass accumulation.

Biohydrogen from Microalgae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubini, Alexandra; Gonzalez-Ballester, David

2016-03-01

This chapter provides an overview of the current state of knowledge of the mechanisms involved in biohydrogen production from microalgae. The known limitations linked to photohydrogen productivity are addressed. Particular attention is given to physiological and molecular strategies to sustain and improve hydrogen production. The impact of different nutrient stresses and the effect of carbon supply on hydrogen production are discussed. The genetic and metabolic engineering approaches for increasing hydrogen production are outlined.

Highly valuable microalgae: biochemical and topological aspects.

PubMed

Pignolet, Olivier; Jubeau, Sébastien; Vaca-Garcia, Carlos; Michaud, Philippe

2013-08-01

The past decade has seen a surge in the interest in microalgae culture for biodiesel production and other applications as renewable biofuels as an alternative to petroleum transport fuels. The development of new technologies for the culture of these photosynthetic microorganisms and improved knowledge of their biochemical composition has spurred innovation in the field of high-value biomolecules. These developments are only economically viable if all the microalgae fractions are valorized in a biorefinery strategy. Achieving this objective requires an understanding of microalgae content and the cellular localization of the main biomolecular families in order to develop efficient harvest and sequential recovery technologies. This review summarizes the state of the art in microalgae compositions and topologies using some examples of the main industrially farmed microalgae.

A Label-Free Microfluidic Biosensor for Activity Detection of Single Microalgae Cells Based on Chlorophyll Fluorescence

PubMed Central

Wang, Junsheng; Sun, Jinyang; Song, Yongxin; Xu, Yongyi; Pan, Xinxiang; Sun, Yeqing; Li, Dongqing

2013-01-01

Detection of living microalgae cells is very important for ballast water treatment and analysis. Chlorophyll fluorescence is an indicator of photosynthetic activity and hence the living status of plant cells. In this paper, we developed a novel microfluidic biosensor system that can quickly and accurately detect the viability of single microalgae cells based on chlorophyll fluorescence. The system is composed of a laser diode as an excitation light source, a photodiode detector, a signal analysis circuit, and a microfluidic chip as a microalgae cell transportation platform. To demonstrate the utility of this system, six different living and dead algae samples (Karenia mikimotoi Hansen, Chlorella vulgaris, Nitzschia closterium, Platymonas subcordiformis, Pyramidomonas delicatula and Dunaliella salina) were tested. The developed biosensor can distinguish clearly between the living microalgae cells and the dead microalgae cells. The smallest microalgae cells that can be detected by using this biosensor are 3 μm ones. Even smaller microalgae cells could be detected by increasing the excitation light power. The developed microfluidic biosensor has great potential for in situ ballast water analysis. PMID:24287532

A mathematical model of intracellular behavior of microalgae for predicting growth and intracellular components syntheses under nutrient replete and deplete conditions.

PubMed

Ryu, Kyung Hwan; Sung, Min-Gyu; Kim, Boeun; Heo, Seongmin; Chang, Yong Keun; Lee, Jay H

2018-06-13

Microalgae is a promising biomass source for renewable fuels and chemicals production. To describe microalgal behavior and improve their cultivation, various kinetic models have been proposed. However, previous works have focused on biomass formation and lipids production only, even though carbohydrates and proteins are also important products, not only for understanding the metabolic behavior of microalgae but also for enhancing the economic viability through value-added side products. In this research, a new mathematical model is proposed to explain core biological mechanisms of growth and macromolecules syntheses based on the central metabolism of carbon and nitrogen. In the model, microalgal growth is separated as hyperplasia and hypertrophy, to describe the cell growth more precisely under nutrient-replete and -deplete conditions. Sensitivity analysis performed using the model indicates that cell state (e.g., cell death rate) has a strong effect on the lipid production explaining the difficulty of reproducing a microalgae culture experiment. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Bio-diesel production directly from the microalgae biomass of Nannochloropsis by microwave and ultrasound radiation.

PubMed

Koberg, Miri; Cohen, Moshe; Ben-Amotz, Ami; Gedanken, Aharon

2011-03-01

This work offers an optimized method for the direct conversion of harvested Nannochloropsis algae into bio-diesel using two novel techniques. The first is a unique bio-technology-based environmental system utilizing flue gas from coal burning power stations for microalgae cultivation. This method reduces considerably the cost of algae production. The second technique is the direct transesterification (a one-stage method) of the Nannochloropsis biomass to bio-diesel production using microwave and ultrasound radiation with the aid of a SrO catalyst. These two techniques were tested and compared to identify the most effective bio-diesel production method. Based on our results, it is concluded that the microwave oven method appears to be the most simple and efficient method for the one-stage direct transesterification of the as-harvested Nannochloropsis algae. Copyright © 2010 Elsevier Ltd. All rights reserved.

Microalgae: a robust "green bio-bridge" between energy and environment.

PubMed

Chen, Yimin; Xu, Changan; Vaidyanathan, Seetharaman

2018-05-01

Microalgae are a potential candidate for biofuel production and environmental treatment because of their specific characteristics (e.g. fast growth, carbon neutral, and rich lipid accumulations). However, several primary bottlenecks still exist in current technologies, including low biomass conversion efficiency, bio-invasion from the external environment, limited or costly nutrient sources, and high energy and capital input for harvest, and stalling its industrial progression. Coupling biofuel production with environmental treatment renders microalgae a more feasible feedstock. This review focuses on microalgae biotechnologies for both bioenergy generation and environmental treatment (e.g. CO 2 sequestration and wastewater reclamation). Different intelligent technologies have been developed, especially during the last decade, to eliminate the bottlenecks, including mixotrophic/heterotrophic cultivation, immobilization, and co-cultivation. It has been realized that any single purpose for the cultivation of microalgae is not an economically feasible option. Combinations of applications in biorefineries are gradually reckoned to be necessary as it provides more economically feasible and environmentally sustainable operations. This presents microalgae as a special niche occupier linking the fields of energy and environmental sciences and technologies. The integrated application of microalgae is also proven by most of the life-cycle analysis studies. This study summarizes the latest development of primary microalgal biotechnologies in the two areas that will bring researchers a comprehensive view towards industrialization with an economic perspective.

Lipid extraction from microalgae using a single ionic liquid

DOEpatents

Salvo, Roberto Di; Reich, Alton; Dykes, Jr., H. Waite H.; Teixeira, Rodrigo

2013-05-28

A one-step process for the lysis of microalgae cell walls and separation of the cellular lipids for use in biofuel production by utilizing a hydrophilic ionic liquid, 1-butyl-3-methylimidazolium. The hydrophilic ionic liquid both lyses the microalgae cell walls and forms two immiscible layers, one of which consists of the lipid contents of the lysed cells. After mixture of the hydrophilic ionic liquid with a suspension of microalgae cells, gravity causes a hydrophobic lipid phase to move to a top phase where it is removed from the mixture and purified. The hydrophilic ionic liquid is recycled to lyse new microalgae suspensions.

Harvesting bioenergy with rationally designed complex functional materials

NASA Astrophysics Data System (ADS)

Kuang, Liangju

A key challenge in renewable energy is to capture, convert and store solar power with earth-abundant materials and environmentally benign technologies. The goal of this thesis is to develop rationally designed complex functional materials for bio-renewable energy applications. On one hand, photoconversion membrane proteins (MPs) are nature's nanoengineering feats for renewable energy management. Harnessing their functions in synthetic systems could help understand, predict, and ultimately control matter and energy at the nanoscale. This is particularly enticing in the post-genome era as recombinant or cell-free expression of many MPs with high yields becomes possible. However, the labile nature of lipid bilayers renders them unsuitable for use in a broad range of engineered systems. A knowledge gap exists about how to design robust synthetic nanomembranes as lipid-bilayer-mimics to support MP functions and how to direct hierarchical MP reconstitution into those membranes to form 2-D or 3-D ordered proteomembrane arrays. Our studies on proteorhodopsin (PR) and bacterial reaction center (BRC), the two light-harvesting MPs, reveal that a charge-interaction-directed reconstitution (CIDR) mechanism induces spontaneous reconstitution of detergent-solubilized MPs into various amphiphilic block copolymer membranes, many of which have far superior stability than lipid bilayers. Our preliminary data also suggest MPs are not enslaved by the biological membranes they derive from; rather, the chemically nonspecific material properties of MP-supporting membranes may act as allosteric regulators. Versatile chemical designs are possible to modulate the conformational energetics of MPs, hence their transport performance in synthetic systems. On the other hand, microalgae are widely regarded as a sustainable feedstock for biofuel production. Microalgae-derived biofuels have not been commercialized yet because current technologies for microalgae dewatering add a huge cost to the final product, and present a major bottleneck. We propose to solve the microalgae dewatering problem in the context of controlling colloidal stability, where inter-algal potential is tuned via surface engineering of novel coagulation agents. We report here a nanoparticle-pinched polymer brush design that combines two known colloidal destabilization agents (e.g., nanoparticle and polymer) into one system, and allows the use of an external field (e.g., magnetic force) to not only modulate inter-algae pair potentials, but also facilitate retrieval of the coagulation agents to be reused after algal oil extraction. We will discuss our extensive data on the preparation of well-defined nanoparticle-pinched polymer brushes, their structure-dependent coagulation performance on both fresh water and marine microalgae species, and their re-suability for continuous cycles of microalgae farming and harvesting.

Mixing Seawater with a Little Wastewater to Produce Bioenergy from Limnetic Algae.

PubMed

Pei, Haiyan; Jiang, Liqun

2018-05-01

Microalgae are considered to be a promising feedstock for biofuel, but expansion of algal lipid production commercially still has a long way to go. Inexhaustible seawater, with a little wastewater added, has great potential to optimize microalga production so that biodiesel production can thrive cost-effectively and sustainably. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wastewater treatment by local microalgae strains for CO2 sequestration and biofuel production

NASA Astrophysics Data System (ADS)

Ansari, Abeera A.; Khoja, Asif Hussain; Nawar, Azra; Qayyum, Muneeb; Ali, Ehsan

2017-11-01

Currently, the scientific community is keenly working on environmental-friendly processes for the production of clean energy and sustainable development. The study was conducted to cultivate microalgae in raw institutional wastewater for water treatment, enriched production of biomass and CO2 sequestration. The strains which were used in this study are Scenedesmus sp. and Chlorella sp. which were isolated from Kallar Kahar Lake, Pakistan. Both strains were cultivated in synthetic growth medium (Bold's Basal Medium) to enhance biomass production. Afterward, microalgae cultures were inoculated in wastewater sample in mixotrophic mode under ambient conditions. The impurities in wastewater were successfully removed from the original sample by the 7th day of operation. COD 95%, nitrate 99.7% and phosphate 80.5% were removed by applying Scenedesmus sp. Meanwhile, Chlorella sp. reduced 84.86% COD, 98.2% nitrate and 70% phosphate, respectively. Interestingly, sulfates were removed from wastewater completely by both strains. Besides being useful in wastewater remediation, these microalgae strains were subsequently harvested for lipid extraction and potential biofuel production was determined. Therefore, the applied method is an environmentally safe, cost-effective and alternative technology for wastewater treatment. Furthermore, the achieved biomass through this process can be used for the production of biofuels.

DRUM: A New Framework for Metabolic Modeling under Non-Balanced Growth. Application to the Carbon Metabolism of Unicellular Microalgae

PubMed Central

Baroukh, Caroline; Muñoz-Tamayo, Rafael; Steyer, Jean-Philippe; Bernard, Olivier

2014-01-01

Metabolic modeling is a powerful tool to understand, predict and optimize bioprocesses, particularly when they imply intracellular molecules of interest. Unfortunately, the use of metabolic models for time varying metabolic fluxes is hampered by the lack of experimental data required to define and calibrate the kinetic reaction rates of the metabolic pathways. For this reason, metabolic models are often used under the balanced growth hypothesis. However, for some processes such as the photoautotrophic metabolism of microalgae, the balanced-growth assumption appears to be unreasonable because of the synchronization of their circadian cycle on the daily light. Yet, understanding microalgae metabolism is necessary to optimize the production yield of bioprocesses based on this microorganism, as for example production of third-generation biofuels. In this paper, we propose DRUM, a new dynamic metabolic modeling framework that handles the non-balanced growth condition and hence accumulation of intracellular metabolites. The first stage of the approach consists in splitting the metabolic network into sub-networks describing reactions which are spatially close, and which are assumed to satisfy balanced growth condition. The left metabolites interconnecting the sub-networks behave dynamically. Then, thanks to Elementary Flux Mode analysis, each sub-network is reduced to macroscopic reactions, for which simple kinetics are assumed. Finally, an Ordinary Differential Equation system is obtained to describe substrate consumption, biomass production, products excretion and accumulation of some internal metabolites. DRUM was applied to the accumulation of lipids and carbohydrates of the microalgae Tisochrysis lutea under day/night cycles. The resulting model describes accurately experimental data obtained in day/night conditions. It efficiently predicts the accumulation and consumption of lipids and carbohydrates. PMID:25105494

Performance of a sand filter in removal of micro-algae from seawater in aquaculture production systems.

PubMed

Sabiri, N E; Castaing, J B; Massé, A; Jaouen, P

2012-01-01

In this study, a sand filter was used to remove micro-algae from seawater feeding aquaculture ponds. A lab-scale sand filter was used to filter 30,000 cells/mL of Heterocapsa triquetra suspension, a non-toxic micro-alga that has morphological and dimensional (15-20 microm) similarities with Alexandrium sp., one of the smallest toxic micro-algae in seawater. Removal efficiency and capture mechanisms for a fixed superficial velocity (3.5 m/h) were evaluated in relation to size distribution and mean diameter of the sand. Various sands (average diameter ranging between 200 microm and 600 microm) were characterized and used as porous media. The structural parameters of the fixed beds were evaluated for each medium using experimental measurements of pressure drop as a function of superficial velocity over a range of Reynolds numbers covering Darcy's regime and the inertial regime. For a filtration cycle of six hours, the best efficiency (E = 90%) was obtained with the following sand characteristics: sieved sand with a range of grain diameter of 100 and 300 microm and a mean grain diameter equal to 256 microm. Results obtained show the influence of the size distribution of sand on the quality of retention of the micro-algae studied.

Improving polyglucan production in cyanobacteria and microalgae via cultivation design and metabolic engineering.

PubMed

Aikawa, Shimpei; Ho, Shih-Hsin; Nakanishi, Akihito; Chang, Jo-Shu; Hasunuma, Tomohisa; Kondo, Akihiko

2015-06-01

Photosynthetic microorganisms, such as cyanobacteria and microalgae, are currently being investigated as alternative biomass resources for bioethanol production, owing to their benefits, including high-photosynthetic activity and whole-year cultivation without utilization of arable land. Polyglucans comprise the major carbohydrate content of these organisms. Polyglucans can be utilized as a carbon source for microbial fermentation. Although polyglucan production has so far been promoted by nutrient limitation, it must be further enhanced to accommodate market demand. This review focuses on the recent progress in the production of α-polyglucans such asglycogen and starch in cyanobacteria and green microalgae via cultivation design, including modifying the nutrient supply and replacing the growth medium. The control and manipulation of polyglucan metabolism necessitates the elucidation of the polyglucan production mechanism. We reviewed gene expression and metabolite accumulation profiles of cyanobacteria and green microalgae during nutrient limitation-stimulated α-polyglucan accumulation. We also focus on the enhancement in cyanobacterial glycogen production via the genetic engineering of glycolysis, CO2 concentration mechanism, and photosynthetic light-harvesting protein based on the polyglucan accumulation mechanism. The combined strategies of cultivation design and genetic engineering should be considered for further enhancement of polyglucan productivity for bioethanol production. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Batch anaerobic co-digestion of waste activated sludge and microalgae (Chlorella sorokiniana) at mesophilic temperature.

PubMed

Beltrán, Carolina; Jeison, David; Fermoso, Fernando G; Borja, Rafael

2016-08-23

The microalgae Chlorella sorokiniana are used as co-substrate for waste activated sludge (WAS) anaerobic digestion. The specific objective of this research was to evaluate the feasibility of improving methane production from anaerobic digestion of WAS in co-digestion with this microalga, based on an optimized mixture percentage. Thus, the anaerobic co-digestion of both substrates aims to overcome the drawbacks of the anaerobic digestion of single WAS, simultaneously improving its management. Different co-digestion mixtures (0% WAS-100% microalgae; 25% WAS-75% microalgae; 50% WAS-50% microalgae; 75% WAS-25% microalgae; 100% WAS-0% microalgae) were studied. The highest methane yield (442 mL CH4/g VS) was obtained for the mixture with 75% WAS and 25% microalgae. This value was 22% and 39% higher than that obtained in the anaerobic digestion of the sole substrates WAS and microalgae, respectively, as well as 16% and 25% higher than those obtained for the co-digestion mixtures with 25% WAS and 75% microalgae and 50% WAS and 50% microalgae, respectively. The kinetic constant of the process increased 42%, 42% and 12%, respectively, for the mixtures with 25%, 50% and 75% of WAS compared to the substrate without WAS. Anaerobic digestion of WAS, together with C. sorokiniana, has been clearly improved by ensuring its viability, suitability and efficiency.

Engineering strategies for enhancing the production of eicosapentaenoic acid (EPA) from an isolated microalga Nannochloropsis oceanica CY2.

PubMed

Chen, Chun-Yen; Chen, Yu-Chun; Huang, Hsiao-Chen; Huang, Chieh-Chen; Lee, Wen-Lung; Chang, Jo-Shu

2013-11-01

Microalgae have emerged as promising resources for highly unsaturated fatty acids. In this study, an indigenous microalga identified as Nannochloropsis oceanica CY2 was grown photoautotrophically to produce eicosapentaenoic acid (EPA; 20:5, n-3). Specific engineering strategies were employed to stimulate EPA accumulation in the microalgal cells. The results show that BG-11 was the most effective medium to grow N. oceanica CY2, giving an EPA content and biomass concentration of 2.38% (per dry cell weight) and 1.53 g/l. The EPA content nearly doubled when using the optimal nitrogen source (NaNO3) at a concentration of 1.50 g/l. The illumination system also markedly affected the EPA content for the photoautotrophic microalga. When the microalgal culture was illuminated with a red LED, an impressively high EPA content of 5.5% was obtained. Finally, using semi-batch cultures operations with LED-blue illumination, the EPA content of N. oceanica CY2 was stably maintained at 5.0%. Copyright © 2013 Elsevier Ltd. All rights reserved.

Biorefinery of microalgae - opportunities and constraints for different production scenarios.

PubMed

Hariskos, Ioanna; Posten, Clemens

2014-06-01

In order to design economically feasible production processes it is necessary, as part of the biorefinery concept, to valorize all constituents of the microalgal biomass. Such an approach requires appropriate biorefinery side-process strategies to be adapted to production of the primary product. These strategies are particularly valid for microalgae, since the composition and amount of residual biomass can vary significantly depending on cell stoichiometry and cultivation techniques. This review investigates opportunities and constraints for biorefinery concepts in production scenarios for four different products from microalgae with different market volumes, including high- and medium-value products, whole cells and biodiesel. Approaches to close material and energy balances, as well as to adapt the biorefinery according to biological potential, process routes, and market needs are presented, which will further contribute to making the biorefinery concept a success. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microalgae biorefineries: The Brazilian scenario in perspective.

PubMed

Brasil, B S A F; Silva, F C P; Siqueira, F G

2017-10-25

Biorefineries have the potential to meet a significant part of the growing demand for energy, fuels, chemicals and materials worldwide. Indeed, the bio-based industry is expected to play a major role in energy security and climate change mitigation during the 21th century. Despite this, there are challenges related to resource consumption, processing optimization and waste minimization that still need to be overcome. In this context, microalgae appear as a promising non-edible feedstock with advantages over traditional land crops, such as high productivity, continuous harvesting throughout the year and minimal problems regarding land use. Importantly, both cultivation and microalgae processing can take place at the same site, which increases the possibilities for process integration and a reduction in logistic costs at biorefinery facilities. This review describes the actual scenario for microalgae biorefineries integration to the biofuels and petrochemical industries in Brazil, while highlighting the major challenges and recent advances in microalgae large-scale production. Copyright © 2016 Elsevier B.V. All rights reserved.

Cell-wall disruption and lipid/astaxanthin extraction from microalgae: Chlorella and Haematococcus.

PubMed

Kim, Dong-Yeon; Vijayan, Durairaj; Praveenkumar, Ramasamy; Han, Jong-In; Lee, Kyubock; Park, Ji-Yeon; Chang, Won-Seok; Lee, Jin-Suk; Oh, You-Kwan

2016-01-01

Recently, biofuels and nutraceuticals produced from microalgae have emerged as major interests, resulting in intensive research of the microalgal biorefinery process. In this paper, recent developments in cell-wall disruption and extraction methods are reviewed, focusing on lipid and astaxanthin production from the biotechnologically important microalgae Chlorella and Haematococcus, respectively. As a common, critical bottleneck for recovery of intracellular components such as lipid and astaxanthin from these microalgae, the composition and structure of rigid, thick cell-walls were analyzed. Various chemical, physical, physico-chemical, and biological methods applied for cell-wall breakage and lipid/astaxanthin extraction from Chlorella and Haematococcus are discussed in detail and compared based on efficiency, energy consumption, type and dosage of solvent, biomass concentration and status (wet/dried), toxicity, scalability, and synergistic combinations. This report could serve as a useful guide to the implementation of practical downstream processes for recovery of valuable products from microalgae including Chlorella and Haematococcus. Copyright © 2015 Elsevier Ltd. All rights reserved.

Advanced treatment of residual nitrogen from biologically treated coke effluent by a microalga-mediated process using volatile fatty acids (VFAs) under stepwise mixotrophic conditions.

PubMed

Ryu, Byung-Gon; Kim, Woong; Heo, Sung-Woon; Kim, Donghyun; Choi, Gang-Guk; Yang, Ji-Won

2015-09-01

This work describes the development of a microalga-mediated process for simultaneous removal of residual ammonium nitrogen (NH4(+)-N) and production of lipids from biologically treated coke effluent. Four species of green algae were tested using a sequential mixotrophic process. In the first phase-CO2-supplied mixotrophic condition-all microalgae assimilated NH4(+)-N with no evident inhibition. In second phase-volatile fatty acids (VFAs)-supplied mixotrophic condition-removal rates of NH4(+)-N and biomass significantly increased. Among the microalgae used, Arctic Chlorella sp. ArM0029B had the highest rate of NH4(+)-N removal (0.97 mg/L/h) and fatty acid production (24.9 mg/L/d) which were 3.6- and 2.1-fold higher than those observed under the CO2-supplied mixotrophic condition. Redundancy analysis (RDA) indicated that acetate and butyrate were decisive factors for increasing NH4(+)-N removal and fatty acid production. These results demonstrate that microalgae can be used in a sequential process for treatment of residual nitrogen after initial treatment of activated sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of colour temperatures in the cultivation of Dunaliella salina and Nannochloropsis oculata in the production of lipids and carbohydrates.

PubMed

Pavón-Suriano, Salim Gabriel; Ortega-Clemente, Luis Alfredo; Curiel-Ramírez, Sergio; Jiménez-García, María Isabel; Pérez-Legaspi, Ignacio Alejandro; Robledo-Narváez, Paula Natalia

2017-07-25

The production of biofuels from microalgae is a promising and sustainable alternative. Its production is determined by the content of lipids and carbohydrates, which is different for each microalgae species and is affected by environmental factors, being lighting one of the principal determining their biochemical composition. The colour temperature (electromagnetic radiation and light spectrum) is a determining factor for the production of lipids and carbohydrates in microalgae. The aim of this assay was to evaluate the effect of three colour temperatures (6500, 10,000 and 20,000 °K) on the biomass (cel mL -1 ), biomass production and productivity (g L -1 and g L -1  day -1 ), lipid and carbohydrate content (%), lipid and carbohydrate production and productivity (mg L -1 and mg L -1  day -1 ), composition and content of fatty acids (%) in two microalgae species: Dunaliella salina and Nannochloropsis oculata. The highest cell density was observed for N. oculata in stationary phase in the control (83.93 × 106 cel mL -1 ). However, higher lipid content was obtained in D. salina in stationary phase at 10,000 °K (80%), while N. oculata showed 67% at 6500 °K. The highest carbohydrate content was 25% in stationary phase for D. salina at 20,000 °K. Regarding the production of lipids, D. salina reached a maximum of 523 mg L -1 in exponential phase at 6500 and 10,000 °K. The highest carbohydrate production was 38 mg L -1 for D. salina in exponential phase at 20,000 °K. In both microalgae, 15 different fatty acids were identified; the most abundant was palmitic acid with 35.8% for N. oculata in stationary phase at 10,000 °K, while D. salina showed 67% of polyunsaturated fatty acids in exponential phase at 6500 °K. In conclusion, the ideal colour temperature for microalgae culture to obtain biofuels should be based on the biomolecule of interest, being necessary to individually evaluate for each species.

Extraction fatty acid as a source to produce biofuel in microalgae Chlorella sp. and Spirulina sp. using supercritical carbon dioxide

NASA Astrophysics Data System (ADS)

Tai, Do Chiem; Hai, Dam Thi Thanh; Vinh, Nguyen Hanh; Phung, Le Thi Kim

2016-06-01

In this research, the fatty acids of isolated microalgae were extracted by some technologies such as maceration, Soxhlet, ultrasonic-assisted extraction and supercritical fluid extraction; and analyzed for biodiesel production using GC-MS. This work deals with the extraction of microalgae oil from dry biomass by using supercritical fluid extraction method. A complete study at laboratory of the influence of some parameters on the extraction kinetics and yields and on the composition of the oil in terms of lipid classes and profiles is proposed. Two types of microalgae were studied: Chlorella sp. and Spirulina sp. For the extraction of oil from microalgae, supercritical CO2 (SC-CO2) is regarded with interest, being safer than n-hexane and offering a negligible environmental impact, a short extraction time and a high-quality final product. Whilst some experimental papers are available on the supercritical fluid extraction (SFE) of oil from microalgae, only limited information exists on the kinetics of the process. These results demonstrate that supercritical CO2 extraction is an efficient method for the complete recovery of the neutral lipid phase.

Genetic Engineering of Algae for Enhanced Biofuel Production ▿

PubMed Central

Radakovits, Randor; Jinkerson, Robert E.; Darzins, Al; Posewitz, Matthew C.

2010-01-01

There are currently intensive global research efforts aimed at increasing and modifying the accumulation of lipids, alcohols, hydrocarbons, polysaccharides, and other energy storage compounds in photosynthetic organisms, yeast, and bacteria through genetic engineering. Many improvements have been realized, including increased lipid and carbohydrate production, improved H2 yields, and the diversion of central metabolic intermediates into fungible biofuels. Photosynthetic microorganisms are attracting considerable interest within these efforts due to their relatively high photosynthetic conversion efficiencies, diverse metabolic capabilities, superior growth rates, and ability to store or secrete energy-rich hydrocarbons. Relative to cyanobacteria, eukaryotic microalgae possess several unique metabolic attributes of relevance to biofuel production, including the accumulation of significant quantities of triacylglycerol; the synthesis of storage starch (amylopectin and amylose), which is similar to that found in higher plants; and the ability to efficiently couple photosynthetic electron transport to H2 production. Although the application of genetic engineering to improve energy production phenotypes in eukaryotic microalgae is in its infancy, significant advances in the development of genetic manipulation tools have recently been achieved with microalgal model systems and are being used to manipulate central carbon metabolism in these organisms. It is likely that many of these advances can be extended to industrially relevant organisms. This review is focused on potential avenues of genetic engineering that may be undertaken in order to improve microalgae as a biofuel platform for the production of biohydrogen, starch-derived alcohols, diesel fuel surrogates, and/or alkanes. PMID:20139239

Microalgae as feedstock for biodiesel production under ultrasound treatment - A review.

PubMed

Sivaramakrishnan, Ramachandran; Incharoensakdi, Aran

2018-02-01

The application of ultrasound in biodiesel production has recently emerged as a novel technology. Ultrasound treatment enhances the mass transfer characteristics leading to the increased reaction rate with short reaction time and potentially reduces the production cost. In this review, application of ultrasound-assisted biodiesel production using acid, base and enzyme catalysts is presented. A critical assessment of the current status of ultrasound in biodiesel production was discussed with the emphasis on using ultrasound for efficient microalgae biodiesel production. The ultrasound in the biodiesel production enhances the emulsification of immiscible liquid reactant by microturbulence generated by cavitation bubbles. The major benefit of the ultrasound-assisted biodiesel production is a reduction in reaction time. Several different methods have been discussed to improve the biodiesel production. Overall, this review focuses on the current understanding of the application of ultrasound in biodiesel production from microalgae and to provide insights into future developments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Microalgae as healthy ingredients for functional food: a review.

PubMed

Matos, J; Cardoso, C; Bandarra, N M; Afonso, C

2017-08-01

Microalgae are very interesting and valuable natural sources of highly valuable bioactive compounds, such as vitamins, essential amino acids, polyunsaturated fatty acids, minerals, carotenoids, enzymes and fibre. Due to their potential, microalgae have become some of the most promising and innovative sources of new food and functional products. Moreover, microalgae can be used as functional ingredients to enhance the nutritional value of foods and, thus, to favourably affect human health by improving the well-being and quality of life, but also by curtailing disease and illness risks. This review provides an overview of the current knowledge of the health benefits associated with the consumption of microalgae, bioactive compounds, functional ingredients, and health foods.

From hybridomas to a robust microalgal-based production platform: molecular design of a diatom secreting monoclonal antibodies directed against the Marburg virus nucleoprotein.

PubMed

Hempel, Franziska; Maurer, Michael; Brockmann, Björn; Mayer, Christian; Biedenkopf, Nadine; Kelterbaum, Anne; Becker, Stephan; Maier, Uwe G

2017-07-27

The ideal protein expression system should provide recombinant proteins in high quality and quantity involving low production costs only. However, especially for complex therapeutic proteins like monoclonal antibodies many challenges remain to meet this goal and up to now production of monoclonal antibodies is very costly and delicate. Particularly, emerging disease outbreaks like Ebola virus in Western Africa in 2014-2016 make it necessary to reevaluate existing production platforms and develop robust and cheap alternatives that are easy to handle. In this study, we engineered the microalga Phaeodactylum tricornutum to produce monoclonal IgG antibodies against the nucleoprotein of Marburg virus, a close relative of Ebola virus causing severe hemorrhagic fever with high fatality rates in humans. Sequences for both chains of a mouse IgG antibody were retrieved from a murine hybridoma cell line and implemented in the microalgal system. Fully assembled antibodies were shown to be secreted by the alga and antibodies were proven to be functional in western blot, ELISA as well as IFA studies just like the original hybridoma produced IgG. Furthermore, synthetic variants with constant regions of a rabbit IgG and human IgG with optimized codon usage were produced and characterized. This study highlights the potential of microalgae as robust and low cost expression platform for monoclonal antibodies secreting IgG antibodies directly into the culture medium. Microalgae possess rapid growth rates, need basically only water, air and sunlight for cultivation and are very easy to handle.

Metabolism in anoxic permeable sediments is dominated by eukaryotic dark fermentation

NASA Astrophysics Data System (ADS)

Bourke, Michael F.; Marriott, Philip J.; Glud, Ronnie N.; Hasler-Sheetal, Harald; Kamalanathan, Manoj; Beardall, John; Greening, Chris; Cook, Perran L. M.

2017-01-01

Permeable sediments are common across continental shelves and are critical contributors to marine biogeochemical cycling. Organic matter in permeable sediments is dominated by microalgae, which as eukaryotes have different anaerobic metabolic pathways to bacteria and archaea. Here we present analyses of flow-through reactor experiments showing that dissolved inorganic carbon is produced predominantly as a result of anaerobic eukaryotic metabolic activity. In our experiments, anaerobic production of dissolved inorganic carbon was consistently accompanied by large dissolved H2 production rates, suggesting the presence of fermentation. The production of both dissolved inorganic carbon and H2 persisted following administration of broad spectrum bactericidal antibiotics, but ceased following treatment with metronidazole. Metronidazole inhibits the ferredoxin/hydrogenase pathway of fermentative eukaryotic H2 production, suggesting that pathway as the source of H2 and dissolved inorganic carbon production. Metabolomic analysis showed large increases in lipid production at the onset of anoxia, consistent with documented pathways of anoxic dark fermentation in microalgae. Cell counts revealed a predominance of microalgae in the sediments. H2 production was observed in dark anoxic cultures of diatoms (Fragilariopsis sp.) and a chlorophyte (Pyramimonas) isolated from the study site, substantiating the hypothesis that microalgae undertake fermentation. We conclude that microalgal dark fermentation could be an important energy-conserving pathway in permeable sediments.

Metabolism in anoxic permeable sediments is dominated by eukaryotic dark fermentation

PubMed Central

Bourke, Michael F; Marriott, Philip J.; Glud, Ronnie N.; Hasler-Sheetal, Harald; Kamalanathan, Manoj; Beardall, John; Greening, Chris; Cook, Perran L.M.

2016-01-01

Permeable sediments are common across continental shelves and are critical contributors to marine biogeochemical cycling. Organic matter in permeable sediments is dominated by microalgae, which as eukaryotes have different anaerobic metabolic pathways to prokaryotes such as bacteria and archaea. Here we present analyses of flow-through reactor experiments showing that dissolved inorganic carbon is produced predominantly as a result of anaerobic eukaryotic metabolic activity. In our experiments, anaerobic production of dissolved inorganic carbon was consistently accompanied by large dissolved H2 production rates, suggesting the presence of fermentation. The production of both dissolved inorganic carbon and H2 persisted following administration of broad spectrum bactericidal antibiotics, but ceased following treatment with metronidazole. Metronidazole inhibits the ferredoxin/hydrogenase pathway of fermentative eukaryotic H2 production, suggesting that pathway as the source of H2 and dissolved inorganic carbon production. Metabolomic analysis showed large increases in lipid production at the onset of anoxia, consistent with documented pathways of anoxic dark fermentation in microalgae. Cell counts revealed a predominance of microalgae in the sediments. H2 production was observed in dark anoxic cultures of diatoms (Fragilariopsis sp.) and a chlorophyte (Pyramimonas) isolated from the study site, substantiating the hypothesis that microalgae undertake fermentation. We conclude that microalgal dark fermentation could be an important energy-conserving pathway in permeable sediments. PMID:28070216

Exploration of upstream and downstream process for microwave assisted sustainable biodiesel production from microalgae Chlorella vulgaris.

PubMed

Sharma, Amit Kumar; Sahoo, Pradeepta Kumar; Singhal, Shailey; Joshi, Girdhar

2016-09-01

The present study explores the integrated approach for the sustainable production of biodiesel from Chlorella vulgaris microalgae. The microalgae were cultivated in 10m(2) open raceway pond at semi-continuous mode with optimum volumetric and areal production of 28.105kg/L/y and 71.51t/h/y, respectively. Alum was used as flocculent for harvesting the microalgae and optimized at different pH. Lipid was extracted using chloroform: methanol (2:1) and having 12.39% of FFA. Effect of various reaction conditions such as effect of catalyst, methanol:lipid ratio, reaction temperature and time on biodiesel yields were studied under microwave irradiation; and 84.01% of biodiesel yield was obtained under optimized reaction conditions. A comparison was also made between the biodiesel productions under conventional heating and microwave irradiation. The synthesized biodiesel was characterized by (1)H NMR, (13)C NMR, FTIR and GC; however, fuel properties of biodiesel were also studied using specified test methods as per ASTM and EN standards. Copyright © 2016 Elsevier Ltd. All rights reserved.

Local bioprospecting for high-lipid producing microalgal strains to be grown on concentrated municipal wastewater for biofuel production.

PubMed

Zhou, Wenguang; Li, Yecong; Min, Min; Hu, Bing; Chen, Paul; Ruan, Roger

2011-07-01

Mass cultivation of microalgae for biofuel production depends heavily on the performance of the microalgae strains used. In this study, 60 algae-like microorganisms collected from different sampling sites in Minnesota were examined using multi-step screening and acclimation procedures to select high-lipid producing facultative heterotrophic microalgae strains capable of growing on concentrated municipal wastewater (CMW) for simultaneous energy crop production and wastewater treatment. Twenty-seven facultative heterotrophic microalgae strains were found, among which 17 strains were proved to be tolerant to CMW. These 17 top-performing strains were identified through morphological observation and DNA sequencing as Chlorella sp., Heynigia sp., Hindakia sp., Micractinium sp., and Scenedesmus sp. Five strains were chosen for other studies because of their ability to adapt to CMW, high growth rates (0.455-0.498 d(-1)) and higher lipid productivities (74.5-77.8 mg L(-1)d(-1)). These strains are considered highly promising compared with other strains reported in the literature. Copyright © 2011 Elsevier Ltd. All rights reserved.

Biochemical methane potential of microalgae: influence of substrate to inoculum ratio, biomass concentration and pretreatment.

PubMed

Alzate, M E; Muñoz, R; Rogalla, F; Fdz-Polanco, F; Pérez-Elvira, S I

2012-11-01

The anaerobic digestion of three microalgae mixtures was evaluated at different substrate to inoculum (S/I) ratios (0.5, 1 and 3), biomass concentrations (3, 10 and 20gTS/kg) and pretreatments (thermal hydrolysis, ultrasound and biological treatment). An S/I ratio of 0.5 and 10gTS/kg resulted in the highest final methane productivities regardless of the microalgae tested (ranging from 188 to 395mL CH(4)/gVS(added)). The biological pretreatment supported negligible enhancements on CH(4) productivity, while the highest increase (46-62%) was achieved for the thermal hydrolysis. The optimum temperature of this pretreatment depended on the microalgae species. The ultrasound pretreatment brought about increases in CH(4) productivity ranging from 6% to 24% at 10,000kJ/kgTS, without further increases at higher energy inputs. The results here obtained confirmed the lack of correlation between the solubilization degree and the methane enhancement potential and pointed out that anaerobic digestion of algae after thermal pretreatment is a promising technology for renewable energy production. Copyright © 2012 Elsevier Ltd. All rights reserved.

Biohydrogen and methane production via a two-step process using an acid pretreated native microalgae consortium.

PubMed

Carrillo-Reyes, Julian; Buitrón, Germán

2016-12-01

A native microalgae consortium treated under thermal-acidic hydrolysis was used to produce hydrogen and methane in a two-step sequential process. Different acid concentrations were tested, generating hydrogen and methane yields of up to 45mLH 2 gVS -1 and 432mLCH 4 gVS -1 , respectively. The hydrogen production step solubilized the particulate COD (chemical oxygen demand) up to 30%, creating considerable amounts of volatile fatty acids (up to 10gCODL -1 ). It was observed that lower acid concentration presented higher hydrogen and methane production potential. The results revealed that thermal acid hydrolysis of a native microalgae consortium is a simple but effective strategy for producing hydrogen and methane in the sequential process. In addition to COD removal (50-70%), this method resulted in an energy recovery of up to 15.9kJ per g of volatile solids of microalgae biomass, one of the highest reported. Copyright © 2016 Elsevier Ltd. All rights reserved.

Production of biodiesel from Coelastrella sp. microalgae

NASA Astrophysics Data System (ADS)

Mansur, Dieni; Fitriady, Muhammad Arifuddin; Susilaningsih, Dwi; Simanungkalit, Sabar Pangihutan

2017-11-01

Microalgae have a wide area of usage and one of them it can be used for biodiesel production. In biodiesel production, lipids containing triglyceride or free fatty acid are converted into methyl ester through trans/esterification reactions. Lipids from microalgae can be extracted by acetone and dimethyl carbonate using homogenizer. Esterification of the lipids was investigated using various catalysts and source of methyl group. Activity of homogeneous catalyst such as HCl and H2SO4 and heterogeneous catalysts such as montmorillonit K-10 and ledgestone was investigated. Moreover, methanol and dimethyl carbonate as source of methyl group were also studied. Among of catalysts with methanol as source of methyl group, it was found that yield of crude biodiesel derived from Choelestrella Sp. microalgae was high over H2SO4 catalyst. On the other hand, over H2SO4 catalyst using dimethyl carbonate as source of methyl group, yield of crude biodiesel significant increase. However, FAME composition of crude biodiesel was high over HCl catalyst.

Bicarbonate supplementation enhanced biofuel production potential as well as nutritional stress mitigation in the microalgae Scenedesmus sp. CCNM 1077.

PubMed

Pancha, Imran; Chokshi, Kaumeel; Ghosh, Tonmoy; Paliwal, Chetan; Maurya, Rahulkumar; Mishra, Sandhya

2015-10-01

The aim of the present study was to find out the optimum sodium bicarbonate concentration to produce higher biomass with higher lipid and carbohydrate contents in microalgae Scenedesmus sp. CCNM 1077. The role of bicarbonate supplementation under different nutritional starvation conditions was also evaluated. The results clearly indicate that 0.6 g/L sodium bicarbonate was optimum concentration resulting in 20.91% total lipid and 25.56% carbohydrate along with 23% increase in biomass production compared to normal growth condition. Addition of sodium bicarbonate increased the activity of nutrient assimilatory enzymes, biomass, lipid and carbohydrate contents under different nutritional starvation conditions. Nitrogen starvation with bicarbonate supplementation resulted in 54.03% carbohydrate and 34.44% total lipid content in microalgae Scenedesmus sp. CCNM 1077. These findings show application of bicarbonate grown microalgae Scenedesmus sp. CCNM 1077 as a promising feedstock for biodiesel and bioethanol production. Copyright © 2015 Elsevier Ltd. All rights reserved.

Salinity induced oxidative stress enhanced biofuel production potential of microalgae Scenedesmus sp. CCNM 1077.

PubMed

Pancha, Imran; Chokshi, Kaumeel; Maurya, Rahulkumar; Trivedi, Khanjan; Patidar, Shailesh Kumar; Ghosh, Arup; Mishra, Sandhya

2015-01-01

Microalgal biomass is considered as potential feedstock for biofuel production. Enhancement of biomass, lipid and carbohydrate contents in microalgae is important for the commercialization of microalgal biofuels. In the present study, salinity stress induced physiological and biochemical changes in microalgae Scenedesmus sp. CCNM 1077 were studied. During single stage cultivation, 33.13% lipid and 35.91% carbohydrate content was found in 400 mM NaCl grown culture. During two stage cultivation, salinity stress of 400 mM for 3 days resulted in 24.77% lipid (containing 74.87% neutral lipid) along with higher biomass compared to single stage, making it an efficient strategy to enhance biofuel production potential of Scenedesmus sp. CCNM 1077. Apart from biochemical content, stress biomarkers like hydrogen peroxide, lipid peroxidation, ascorbate peroxidase, proline and mineral contents were also studied to understand the role of reactive oxygen species (ROS) mediated lipid accumulation in microalgae Scenedesmus sp. CCNM 1077. Copyright © 2015 Elsevier Ltd. All rights reserved.

Hyperspectral imaging of microalgae using two-photon excitation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinclair, Michael B.; Melgaard, David Kennett; Reichardt, Thomas A.

2010-10-01

A considerable amount research is being conducted on microalgae, since microalgae are becoming a promising source of renewable energy. Most of this research is centered on lipid production in microalgae because microalgae produce triacylglycerol which is ideal for biodiesel fuels. Although we are interested in research to increase lipid production in algae, we are also interested in research to sustain healthy algal cultures in large scale biomass production farms or facilities. The early detection of fluctuations in algal health, productivity, and invasive predators must be developed to ensure that algae are an efficient and cost-effective source of biofuel. Therefore wemore » are developing technologies to monitor the health of algae using spectroscopic measurements in the field. To do this, we have proposed to spectroscopically monitor large algal cultivations using LIDAR (Light Detection And Ranging) remote sensing technology. Before we can deploy this type of technology, we must first characterize the spectral bio-signatures that are related to algal health. Recently, we have adapted our confocal hyperspectral imaging microscope at Sandia to have two-photon excitation capabilities using a chameleon tunable laser. We are using this microscope to understand the spectroscopic signatures necessary to characterize microalgae at the cellular level prior to using these signatures to classify the health of bulk samples, with the eventual goal of using of LIDAR to monitor large scale ponds and raceways. By imaging algal cultures using a tunable laser to excite at several different wavelengths we will be able to select the optimal excitation/emission wavelengths needed to characterize algal cultures. To analyze the hyperspectral images generated from this two-photon microscope, we are using Multivariate Curve Resolution (MCR) algorithms to extract the spectral signatures and their associated relative intensities from the data. For this presentation, I will show our two-photon hyperspectral imaging results on a variety of microalgae species and show how these results can be used to characterize algal ponds and raceways.« less

Monster potential meets potential monster: pros and cons of deploying genetically modified microalgae for biofuels production.

PubMed

Flynn, K J; Mitra, A; Greenwell, H C; Sui, J

2013-02-06

Biofuels production from microalgae attracts much attention but remains an unproven technology. We explore routes to enhance production through modifications to a range of generic microalgal physiological characteristics. Our analysis shows that biofuels production may be enhanced ca fivefold through genetic modification (GM) of factors affecting growth rate, respiration, photoacclimation, photosynthesis efficiency and the minimum cell quotas for nitrogen and phosphorous (N : C and P : C). However, simulations indicate that the ideal GM microalgae for commercial deployment could, on escape to the environment, become a harmful algal bloom species par excellence, with attendant risks to ecosystems and livelihoods. In large measure, this is because an organism able to produce carbohydrate and/or lipid at high rates, providing stock metabolites for biofuels production, will also be able to attain a stoichiometric composition that will be far from optimal as food for the support of zooplankton growth. This composition could suppress or even halt the grazing activity that would otherwise control the microalgal growth in nature. In consequence, we recommend that the genetic manipulation of microalgae, with inherent consequences on a scale comparable to geoengineering, should be considered under strict international regulation.

Monster potential meets potential monster: pros and cons of deploying genetically modified microalgae for biofuels production

PubMed Central

Flynn, K. J.; Mitra, A.; Greenwell, H. C.; Sui, J.

2013-01-01

Biofuels production from microalgae attracts much attention but remains an unproven technology. We explore routes to enhance production through modifications to a range of generic microalgal physiological characteristics. Our analysis shows that biofuels production may be enhanced ca fivefold through genetic modification (GM) of factors affecting growth rate, respiration, photoacclimation, photosynthesis efficiency and the minimum cell quotas for nitrogen and phosphorous (N : C and P : C). However, simulations indicate that the ideal GM microalgae for commercial deployment could, on escape to the environment, become a harmful algal bloom species par excellence, with attendant risks to ecosystems and livelihoods. In large measure, this is because an organism able to produce carbohydrate and/or lipid at high rates, providing stock metabolites for biofuels production, will also be able to attain a stoichiometric composition that will be far from optimal as food for the support of zooplankton growth. This composition could suppress or even halt the grazing activity that would otherwise control the microalgal growth in nature. In consequence, we recommend that the genetic manipulation of microalgae, with inherent consequences on a scale comparable to geoengineering, should be considered under strict international regulation. PMID:24427510

Production of bio-jet fuel from microalgae

NASA Astrophysics Data System (ADS)

Elmoraghy, Marian

The increase in petroleum-based aviation fuel consumption, the decrease in petroleum resources, the fluctuation of the crude oil price, the increase in greenhouse gas emission and the need for energy security are motivating the development of an alternate jet fuel. Bio-jet fuel has to be a drop in fuel, technically and economically feasible, environmentally friendly, greener than jet fuel, produced locally and low gallon per Btu. Bic jet fuel has been produced by blending petro-based jet fuel with microalgae biodiesel (Fatty Acid Methyl Ester, or simply FAME). Indoor microalgae growth, lipids extraction and transetrification to biodiesel are energy and fresh water intensive and time consuming. In addition, the quality of the biodiesel product and the physical properties of the bio-jet fuel blends are unknown. This work addressed these challenges. Minimizing the energy requirements and making microalgae growth process greener were accomplished by replacing fluorescent lights with light emitting diodes (LEDs). Reducing fresh water footprint in algae growth was accomplished by waste water use. Microalgae biodiesel production time was reduced using the one-step (in-situ transestrification) process. Yields up to 56.82 mg FAME/g dry algae were obtained. Predicted physical properties of in-situ FAME satisfied European and American standards confirming its quality. Lipid triggering by nitrogen deprivation was accomplished in order to increase the FAME production. Bio-jet fuel freezing points and heating values were measured for different jet fuel to biodiesel blend ratios.

Valorization of Spent Escherichia coli Media Using Green Microalgae Chlamydomonas reinhardtii and Feedstock Production

PubMed Central

Zhang, Jian-Guo; Zhang, Fang; Thakur, Kiran; Hu, Fei; Wei, Zhao-Jun

2017-01-01

The coupling of Chlamydomonas reinhardtii biomass production for nutrients removal of Escherichia coli anaerobic broth (EAB) is thought to be an economically feasible option for the cultivation of microalgae. The feasibility of growing microalgae in using EAB high in nutrients for the production of more biomass was examined. EAB comprised of nutrient-abundant effluents, which can be used to produce microalgae biomass and remove environment pollutant simultaneously. In this study, C. reinhardtii 21gr (cc1690) was cultivated in different diluted E. coli anaerobic broth supplemented with trace elements under mixotrophic and heterotrophic conditions. The results showed that C. reinhardtii grown in 1×, 1/2×, 1/5× and 1/10×E. coli anaerobic broth under mixotrophic conditions exhibited specific growth rates of 2.71, 2.68, 1.45, and 1.13 day-1, and biomass production of 201.9, 184.2, 175.5, and 163.8 mg L-1, respectively. Under heterotrophic conditions, the specific growth rates were 1.80, 1.86, 1.75, and 1.02 day-1, and biomass production were 45.6, 29.4, 15.8, and 12.1 mg L-1, respectively. The removal efficiency of chemical oxygen demand, total-nitrogen and total-phosphorus from 1×E. coli anaerobic broth was 21.51, 22.41, and 15.53%. Moreover, the dry biomass had relatively high carbohydrate (44.3%) and lipid content (18.7%). Therefore, this study provides an environmentally sustainable as well economical method for biomass production in promising model microalgae and subsequently paves the way for industrial use. PMID:28638375

Phytoplankton production systems in a shellfish hatchery: variations of the bacterial load and diversity of vibrios.

PubMed

Dubert, J; Fernández-Pardo, A; Nóvoa, S; Barja, J L; Prado, S

2015-06-01

Outbreaks of disease caused by some Vibrio species represent the main production bottleneck in shellfish hatcheries. Although the phytoplankton used as food is one of the main sources of bacteria, studies of the associated bacterial populations, specifically vibrios, are scarce. The aim of the study was the microbiological monitoring of the microalgae as the first step in assessing the risk disease for bivalve cultures. Two phytoplankton production systems were sampled weekly throughout 1-year period in a bivalve hatchery. Quantitative analysis revealed high levels of marine heterotrophic bacteria in both systems throughout the study. Presumptive vibrios were detected occasionally and at low concentrations. In most of the cases, they belonged to the Splendidus and Harveyi clades. The early detection of vibrios in the microalgae may be the key for a successful bivalve culture. Their abundance and diversity were affected by factors related to the hatchery environment. This work represents the first long study where the presence of vibrios was evaluated rigorously in phytoplankton production systems and provides a suitable microbiological protocol to control and guarantee the quality of the algal cultures to avoid the risk of transferring potential pathogens to shellfish larvae and/or broodstock. © 2015 The Society for Applied Microbiology.

Synergies between agriculture and bioenergy in Latin American countries: A circular economy strategy for bioenergy production in Ecuador.

PubMed

Vega-Quezada, Cristhian; Blanco, María; Romero, Hugo

2017-10-25

This study quantifies the synergies between agriculture and bioenergy considering biodiesel production as part of a set of systemic initiatives. We present a case study in Ecuador taking into account the recent government measures aimed at developing the bioenergy sector. Four scenarios have been evaluated through a newly designed systemic scheme of circular-economy initiatives. These scenarios encompass three production pathways covering three energy crops: palm oil (PO), microalgae in open ponds (M1) and microalgae in laminar photobioreactors (M2). We have applied Benefit-Cost Analysis (BCA) methodology considering the Net Present Value (NPV) and the Benefit-Cost Ratio (BCR) as the main evaluation criteria. In terms of private investment, biodiesel production from PO is more attractive than from M2. However, regarding efficiency and effectiveness of public funds, M2 is superior to PO because the public BCR and NPV are higher, and the pressure on agricultural land is lower. Moreover, M2 as part of a systemic approach presents a better carbon balance. These findings show that, under a systemic approach based on circular economy, strategies like the one analyzed in this study are economically feasible and may have a promising future. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of static magnetic field on the oxygen production of Scenedesmus obliquus cultivated in municipal wastewater.

PubMed

Tu, Renjie; Jin, Wenbiao; Xi, Tingting; Yang, Qian; Han, Song-Fang; Abomohra, Abd El-Fatah

2015-12-01

Algal-bacterial symbiotic system, with biological synergism of physiological functions of both algae and bacteria, has been proposed for cultivation of microalgae in municipal wastewater for biomass production and wastewater treatment. The algal-bacterial symbiotic system can enhance dissolved oxygen production which enhances bacterial growth and catabolism of pollutants in wastewater. Therefore, the oxygen production efficiency of microalgae in algal-bacterial systems is considered as the key factor influencing the wastewater treatment efficiency. In the present study, we have proposed a novel approach which uses static magnetic field to enhance algal growth and oxygen production rate with low operational cost and non-toxic secondary pollution. The performance of oxygen production with the magnetic field was evaluated using Scenedesmus obliquus grown in municipal wastewater and was calculated based on the change in dissolved oxygen concentration. Results indicated that magnetic treatment stimulates both algal growth and oxygen production. Application of 1000 GS of magnetic field once at logarithmic growth phase for 0.5 h increased the chlorophyll-a content by 11.5% over the control after 6 days of growth. In addition, magnetization enhanced the oxygen production rate by 24.6% over the control. Results of the study confirmed that application of a proper magnetic field could reduce the energy consumption required for aeration during the degradation of organic matter in municipal wastewater in algal-bacterial symbiotic systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Production cost of a real microalgae production plant and strategies to reduce it.

PubMed

Acién, F G; Fernández, J M; Magán, J J; Molina, E

2012-01-01

The cost analysis of a real facility for the production of high value microalgae biomass is presented. The facility is based on ten 3 m3 tubular photobioreactors operated in continuous mode for 2 years, data of Scenedesmus almeriensis productivity but also of nutrients and power consumption from this facility being used. The yield of the facility was close to maximum expected for the location of Almería, the annual production capacity being 3.8 t/year (90 t/ha·year) and the photosynthetic efficiency being 3.6%. The production cost was 69 €/kg. Economic analysis shows that labor and depreciation are the major factors contributing to this cost. Simplification of the technology and scale-up to a production capacity of 200 t/year allows to reduce the production cost up to 12.6 €/kg. Moreover, to reduce the microalgae production cost to approaches the energy or commodities markets it is necessary to reduce the photobioreactor cost (by simplifying its design or materials used), use waste water and flue gases, and reduce the power consumption and labor required for the production step. It can be concluded that although it has been reported that production of biofuels from microalgae is relatively close to being economically feasible, data here reported demonstrated that to achieve it by using the current production technologies, it is necessary to substantially reduce their costs and to operate them near their optimum values. Copyright © 2012 Elsevier Inc. All rights reserved.

Photobioreactor cultivation strategies for microalgae and cyanobacteria.

PubMed

Johnson, Tylor J; Katuwal, Sarmila; Anderson, Gary A; Gu, Liping; Zhou, Ruanbao; Gibbons, William R

2018-03-08

The current burden on fossil-derived chemicals and fuels combined with the rapidly increasing global population has led to a crucial need to develop renewable and sustainable sources of chemicals and biofuels. Photoautotrophic microorganisms, including cyanobacteria and microalgae, have garnered a great deal of attention for their capability to produce these chemicals from carbon dioxide, mineralized water, and solar energy. While there have been substantial amounts of research directed at scaling-up production from these microorganisms, several factors have proven difficult to overcome, including high costs associated with cultivation, photobioreactor construction, and artificial lighting. Decreasing these costs will substantially increase the economic feasibility of these production processes. Thus, the purpose of this review is to describe various photobioreactor designs, and then provide an overview on lighting systems, mixing, gas transfer, and the hydrodynamics of bubbles. These factors must be considered when the goal of a production process is economic feasibility. Targets for improving microalgae and cyanobacteria cultivation media, including water reduction strategies will also be described. As fossil fuel reserves continue to be depleted and the world population continues to increase, it is imperative that renewable chemical and biofuel production processes be developed toward becoming economically feasible. Thus, it is essential that future research is directed toward improving these processes. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 2018. © 2018 American Institute of Chemical Engineers.

[Patented photobioreactor to commercial production of new drugs and nutraceuticals from microalgae].

PubMed

Talbierz, Szymon; Kujawska, Natalia; Latała, Adam

2012-01-01

Microalgae - microscopic photosynthetic plants are an inexhaustible source of compounds with potential pharmaceutical applications. However, the development of microalgal biotechnology in particular for the production of new drugs and nutraceuticals has been slowed by the limited growth performance of algae in industrial photobioreactors. This is due to low light intensity, necessary for photosynthesis, which causes growth of algae. Flat-Plate photobioreactor with a solar-tracker system which is reported to protect with the Patent Office of RP enables optimal positioning of culture vessel to the direction of the sun's rays and thus can increase the efficiency of biomass growth (by 30%) and lipid content, compared with photobioreactors without it. The use of the invention in industrial plants can significantly contribute to lower costs and make all the technology more profitable.

Sustainable microalgae for the simultaneous synthesis of carbon quantum dots for cellular imaging and porous carbon for CO2 capture.

PubMed

Guo, Li-Ping; Zhang, Yan; Li, Wen-Cui

2017-05-01

Microalgae biomass is a sustainable source with the potential to produce a range of products. However, there is currently a lack of practical and functional processes to enable the high-efficiency utilization of the microalgae. We report here a hydrothermal process to maximize the utilizability of microalgae biomass. Specifically, our concept involves the simultaneous conversion of microalgae to (i) hydrophilic and stable carbon quantum dots and (ii) porous carbon. The synthesis is easily scalable and eco-friendly. The microalgae-derived carbon quantum dots possess a strong two-photon fluorescence property, have a low cytotoxicity and an efficient cellular uptake, and show potential for high contrast bioimaging. The microalgae-based porous carbons show excellent CO 2 capture capacities of 6.9 and 4.2mmolg -1 at 0 and 25°C respectively, primarily due to the high micropore volume (0.59cm 3 g -1 ) and large specific surface area (1396m 2 g -1 ). Copyright © 2017 Elsevier Inc. All rights reserved.

Pyrolysis characteristics and kinetics of microalgae via thermogravimetric analysis (TGA): A state-of-the-art review.

PubMed

Bach, Quang-Vu; Chen, Wei-Hsin

2017-12-01

Pyrolysis is a promising route for biofuels production from microalgae at moderate temperatures (400-600°C) in an inert atmosphere. Depending on the operating conditions, pyrolysis can produce biochar and/or bio-oil. In practice, knowledge for thermal decomposition characteristics and kinetics of microalgae during pyrolysis is essential for pyrolyzer design and pyrolysis optimization. Recently, the pyrolysis kinetics of microalgae has become a crucial topic and received increasing interest from researchers. Thermogravimetric analysis (TGA) has been employed as a proven technique for studying microalgae pyrolysis in a kinetic control regime. In addition, a number of kinetic models have been applied to process the TGA data for kinetic evaluation and parameters estimation. This paper aims to provide a state-of-the art review on recent research activities in pyrolysis characteristics and kinetics of various microalgae. Common kinetic models predicting the thermal degradation of microalgae are examined and their pros and cons are illustrated. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biodiesel from wet microalgae: extraction with hexane after the microwave-assisted transesterification of lipids.

PubMed

Cheng, Jun; Huang, Rui; Li, Tao; Zhou, Junhu; Cen, Kefa

2014-10-01

A chloroform-free novel process for the efficient production of biodiesel from wet microalgae is proposed. Crude biodiesel is produced through extraction with hexane after microwave-assisted transesterification (EHMT) of lipids in wet microalgae. Effects of different parameters, including reaction temperature, reaction time, methanol dosage, and catalyst dosage, on fatty acids methyl esters (FAMEs) yield are investigated. The yield of FAME extracted into the hexane from the wet microalgae is increased 6-fold after the transesterification of lipids. The yield of FAME obtained through EHMT of lipids in wet microalgae is comparable to that obtained through direct transesterification of dried microalgae biomass with chloroform; however, FAME content in crude biodiesel obtained through EHMT is 86.74%, while that in crude biodiesel obtained through the chloroform-based process is 75.93%. EHMT ensures that polar pigments present in microalgae are not extracted into crude biodiesel, which leads to a 50% reduction in nitrogen content in crude biodiesel. Copyright © 2014 Elsevier Ltd. All rights reserved.

Efficient harvesting of marine Chlorella vulgaris microalgae utilizing cationic starch nanoparticles by response surface methodology.

PubMed

Bayat Tork, Mahya; Khalilzadeh, Rasoul; Kouchakzadeh, Hasan

2017-11-01

Harvesting involves nearly thirty percent of total production cost of microalgae that needs to be done efficiently. Utilizing inexpensive and highly available biopolymer-based flocculants can be a solution for reducing the harvest costs. Herein, flocculation process of Chlorella vulgaris microalgae using cationic starch nanoparticles (CSNPs) was evaluated and optimized through the response surface methodology (RSM). pH, microalgae and CSNPs concentrations were considered as the main independent variables. Under the optimum conditions of microalgae concentration 0.75gdry weight/L, CSNPs concentration 7.1mgdry weight/L and pH 11.8, the maximum flocculation efficiency (90%) achieved. Twenty percent increase in flocculation efficiency observed with the use of CSNPs instead of the non-particulate starch which can be due to the more electrostatic interactions between the cationic nanoparticles and the microalgae. Therefore, the synthesized CSNPs can be employed as a convenient and economical flocculants for efficient harvest of Chlorella vulgaris microalgae at large scale. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of different artificial neural network architectures in modeling of Chlorella sp. flocculation.

PubMed

Zenooz, Alireza Moosavi; Ashtiani, Farzin Zokaee; Ranjbar, Reza; Nikbakht, Fatemeh; Bolouri, Oberon

2017-07-03

Biodiesel production from microalgae feedstock should be performed after growth and harvesting of the cells, and the most feasible method for harvesting and dewatering of microalgae is flocculation. Flocculation modeling can be used for evaluation and prediction of its performance under different affective parameters. However, the modeling of flocculation in microalgae is not simple and has not performed yet, under all experimental conditions, mostly due to different behaviors of microalgae cells during the process under different flocculation conditions. In the current study, the modeling of microalgae flocculation is studied with different neural network architectures. Microalgae species, Chlorella sp., was flocculated with ferric chloride under different conditions and then the experimental data modeled using artificial neural network. Neural network architectures of multilayer perceptron (MLP) and radial basis function architectures, failed to predict the targets successfully, though, modeling was effective with ensemble architecture of MLP networks. Comparison between the performances of the ensemble and each individual network explains the ability of the ensemble architecture in microalgae flocculation modeling.

Prediction of microalgae hydrothermal liquefaction products from feedstock biochemical composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leow, Shijie; Witter, John R.; Vardon, Derek R.

Hydrothermal liquefaction (HTL) uses water under elevated temperatures and pressures (200–350 °C, 5–20 MPa) to convert biomass into liquid “biocrude” oil. Despite extensive reports on factors influencing microalgae cell composition during cultivation and separate reports on HTL products linked to cell composition, the field still lacks a quantitative model to predict HTL conversion product yield and qualities from feedstock biochemical composition; the tailoring of microalgae feedstock for downstream conversion is a unique and critical aspect of microalgae biofuels that must be leveraged upon for optimization of the whole process. This study developed predictive relationships for HTL biocrude yield and othermore » conversion product characteristics based on HTL of Nannochloropsis oculata batches harvested with a wide range of compositions (23–59% dw lipids, 58–17% dw proteins, 12–22% dw carbohydrates) and a defatted batch (0% dw lipids, 75% dw proteins, 19% dw carbohydrates). HTL biocrude yield (33–68% dw) and carbon distribution (49–83%) increased in proportion to the fatty acid (FA) content. A component additivity model (predicting biocrude yield from lipid, protein, and carbohydrates) was more accurate predicting literature yields for diverse microalgae species than previous additivity models derived from model compounds. FA profiling of the biocrude product showed strong links to the initial feedstock FA profile of the lipid component, demonstrating that HTL acts as a water-based extraction process for FAs; the remainder non-FA structural components could be represented using the defatted batch. These findings were used to introduce a new FA-based model that predicts biocrude oil yields along with other critical parameters, and is capable of adjusting for the wide variations in HTL methodology and microalgae species through the defatted batch. Lastly, the FA model was linked to an upstream cultivation model (Phototrophic Process Model), providing for the first time an integrated modeling framework to overcome a critical barrier to microalgae-derived HTL biofuels and enable predictive analysis of the overall microalgal-to-biofuel process.« less

Prediction of microalgae hydrothermal liquefaction products from feedstock biochemical composition

DOE PAGES

Leow, Shijie; Witter, John R.; Vardon, Derek R.; ...

2015-05-11

Hydrothermal liquefaction (HTL) uses water under elevated temperatures and pressures (200–350 °C, 5–20 MPa) to convert biomass into liquid “biocrude” oil. Despite extensive reports on factors influencing microalgae cell composition during cultivation and separate reports on HTL products linked to cell composition, the field still lacks a quantitative model to predict HTL conversion product yield and qualities from feedstock biochemical composition; the tailoring of microalgae feedstock for downstream conversion is a unique and critical aspect of microalgae biofuels that must be leveraged upon for optimization of the whole process. This study developed predictive relationships for HTL biocrude yield and othermore » conversion product characteristics based on HTL of Nannochloropsis oculata batches harvested with a wide range of compositions (23–59% dw lipids, 58–17% dw proteins, 12–22% dw carbohydrates) and a defatted batch (0% dw lipids, 75% dw proteins, 19% dw carbohydrates). HTL biocrude yield (33–68% dw) and carbon distribution (49–83%) increased in proportion to the fatty acid (FA) content. A component additivity model (predicting biocrude yield from lipid, protein, and carbohydrates) was more accurate predicting literature yields for diverse microalgae species than previous additivity models derived from model compounds. FA profiling of the biocrude product showed strong links to the initial feedstock FA profile of the lipid component, demonstrating that HTL acts as a water-based extraction process for FAs; the remainder non-FA structural components could be represented using the defatted batch. These findings were used to introduce a new FA-based model that predicts biocrude oil yields along with other critical parameters, and is capable of adjusting for the wide variations in HTL methodology and microalgae species through the defatted batch. Lastly, the FA model was linked to an upstream cultivation model (Phototrophic Process Model), providing for the first time an integrated modeling framework to overcome a critical barrier to microalgae-derived HTL biofuels and enable predictive analysis of the overall microalgal-to-biofuel process.« less

Cultivation of newly isolated microalgae Coelastrum sp. in wastewater for simultaneous CO2 fixation, lipid production and wastewater treatment.

PubMed

Mousavi, Shokouh; Najafpour, Ghasem D; Mohammadi, Maedeh; Seifi, Mohammad Hasan

2018-04-01

Cultivation of microalgae in wastewater is a promising and cost-effective approach for both CO 2 biofixation and wastewater remediation. In this study, a new strain of Coelastrum sp. was isolated from cattle manure leachate. The isolated microalgae were then cultivated in wastewater. Effects of different sCOD concentrations (600, 750, 900, 1050 mg L -1 ) and light intensities (1000, 2300, 4600, 6900 and 10000 Lux) on biomass production, CO 2 consumption rate and nutrient removal from wastewater were investigated. The results showed that maximum cell growth and CO 2 consumption rate were 2.71 g L -1 and 53.12 mg L -1 day -1 , respectively, which were obtained in the wastewater with 750 mg L -1 sCOD and under the light intensity of 6900 Lux. The microalgae were able to completely consume all CO 2 after incubation period of 4 days. The highest sCOD, total Kjeldahl nitrogen (TKN), nitrate and total phosphorous (TP) removal at such conditions were 53.45, 91.18, 87.51 and 100%, respectively. The lipid content of microalgal biomass was also measured under different light intensities; maximum amount of lipid was determined to be 50.77% under illumination of 2300 Lux. Finally, the CO 2 consumption rate and biomass productivity of microalgae in semi-batch culture with continuous gas flow (CO 2 6%:N 2 94%) were investigated. The rate of CO 2 consumption and biomass productivity were 0.528 and 0.281 g L -1 day -1 , respectively. The TKN, nitrate, TP and sCOD removal rate of microalgae were 83.51, 80.91, 100, 41.4%, respectively.

Genetic Engineering: A Promising Tool to Engender Physiological, Biochemical, and Molecular Stress Resilience in Green Microalgae

PubMed Central

Guihéneuf, Freddy; Khan, Asif; Tran, Lam-Son P.

2016-01-01

As we march into the 21st century, the prevailing scenario of depleting energy resources, global warming and ever increasing issues of human health and food security will quadruple. In this context, genetic and metabolic engineering of green microalgae complete the quest toward a continuum of environmentally clean fuel and food production. Evolutionarily related, but unlike land plants, microalgae need nominal land or water, and are best described as unicellular autotrophs using light energy to fix atmospheric carbon dioxide (CO2) into algal biomass, mitigating fossil CO2 pollution in the process. Remarkably, a feature innate to most microalgae is synthesis and accumulation of lipids (60–65% of dry weight), carbohydrates and secondary metabolites like pigments and vitamins, especially when grown under abiotic stress conditions. Particularly fruitful, such an application of abiotic stress factors such as nitrogen starvation, salinity, heat shock, etc., can be used in a biorefinery concept for production of multiple valuable products. The focus of this mini-review underlies metabolic reorientation practices and tolerance mechanisms as applied to green microalgae under specific stress stimuli for a sustainable pollution-free future. Moreover, we entail current progress on genetic engineering as a promising tool to grasp adaptive processes for improving strains with potential biotechnological interests. PMID:27066043

Recent Developments on the Production of Transportation Fuels via Catalytic Conversion of Microalgae: Experiments and Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Fan; Wang, Ping; Duan, Yuhua

2012-08-02

Due to continuing high demand, depletion of non-renewable resources and increasing concerns about climate change, the use of fossil fuel-derived transportation fuels faces relentless challenges both from a world markets and an environmental perspective. The production of renewable transportation fuel from microalgae continues to attract much attention because of its potential for fast growth rates, high oil content, ability to grow in unconventional scenarios, and inherent carbon neutrality. Moreover, the use of microalgae would minimize “food versus fuel” concerns associated with several biomass strategies, as microalgae do not compete with food crops in the food chain. This paper reviews themore » progress of recent research on the production of transportation fuels via homogeneous and heterogeneous catalytic conversions of microalgae. This review also describes the development of tools that may allow for a more fundamental understanding of catalyst selection and conversion processes using computational modelling. The catalytic conversion reaction pathways that have been investigated are fully discussed based on both experimental and theoretical approaches. Finally, this work makes several projections for the potential of various thermocatalytic pathways to produce alternative transportation fuels from algae, and identifies key areas where the authors feel that computational modelling should be directed to elucidate key information to optimize the process.« less

An informatics-based analysis of developments to date and prospects for the application of microalgae in the biological sequestration of industrial flue gas.

PubMed

Zhu, Xi; Rong, Junfeng; Chen, Hui; He, Chenliu; Hu, Wensheng; Wang, Qiang

2016-03-01

The excessive emission of flue gas contributes to air pollution, abnormal climate change, global warming, and sea level rises associated with glacial melting. With the ability to utilize NOx as a nitrogen source and to convert solar energy into chemical energy via CO2 fixation, microalgae can potentially reduce air pollution and relax global warming, while also enhancing biomass and biofuel production as well as the production of high-value-added products. This informatics-based review analyzes the trends in the related literature and in patent activity to draw conclusions and to offer a prospective view on the developments of microalgae for industrial flue gas biosequestration. It is revealed that in recent years, microalgal research for industrial flue gas biosequestration has started to attract increasing attention and has now developed into a hot research topic, although it is still at a relatively early stage, and needs more financial and policy support in order to better understand microalgae and to develop an economically viable process. In comparison with onsite microalgal CO2 capture, microalgae-based biological DeNOx appears to be a more realistic and attractive alternative that could be applied to NOx treatment.

Enhanced accumulation of starch and total carbohydrates in alginate-immobilized Chlorella spp. induced by Azospirillum brasilense: I. Autotrophic conditions.

PubMed

Choix, Francisco J; de-Bashan, Luz E; Bashan, Yoav

2012-10-10

The effect of the microalgae-growth promoting bacterium Azospirillum brasilense on accumulation of total carbohydrates and starch in two species of Chlorella (Chlorella vulgaris and Chlorella sorokiniana), when the bacterium and each microalga were jointly immobilized in alginate beads was studied under autotrophic conditions for 144 h in synthetic medium. The interaction of the bacterium with the microalgae enhanced accumulation of total carbohydrate and starch. Cells of Chlorella accumulated the highest amounts of carbohydrate after incubation for 24h. Yet, this did not coincide with the highest affinity and volumetric productivity measured in these cultures. However, after incubation for 72 h, mainly in jointly immobilized treatments of both microalgae species, the cultures reached their highest total carbohydrate content (mainly as starch) and also the highest affinity and volumetric productivity. These results demonstrate the potential of A. brasilense to affect carbohydrates and starch accumulation in Chlorella spp. when both microorganisms are co-cultured, which can be an important tool for applications of microalgae. Copyright © 2012. Published by Elsevier Inc.

Optimal control of nutrition restricted dynamics model of Microalgae biomass growth model

NASA Astrophysics Data System (ADS)

Ratianingsih, R.; Azim; Nacong, N.; Resnawati; Mardlijah; Widodo, B.

2017-12-01

The biomass of the microalgae is very potential to be proposed as an alternative renewable energy resources because it could be extracted into lipid. Afterward, the lipid could be processed to get the biodiesel or bioethanol. The extraction of the biomass on lipid synthesis process is very important to be studied because the process just gives some amount of lipid. A mathematical model of restricted microalgae biomass growth just gives 1/3 proportion of lipid with respect to the biomass in the synthesis process. An optimal control is designed to raise the ratio between the number of lipid formation and the microalgae biomass to be used in synthesis process. The minimum/ Pontryagin maximum principle is used to get the optimal lipid production. The simulation shows that the optimal lipid formation could be reach by simultaneously controlling the carbon dioxide, in the respiration and photosynthesis the process, and intake nutrition rates of liquid waste and urea substrate. The production of controlled microalgae lipid could be increase 6.5 times comparing to the uncontrolled one.

Production of long chain omega-3 fatty acids and carotenoids in tropical areas by a new heat-tolerant microalga Tetraselmis sp. DS3.

PubMed

Tsai, Hsin-Pei; Chuang, Lu-Te; Chen, Ching-Nen Nathan

2016-02-01

Demand for long chain ω-3 fatty acids from non-fish source for vegetarians has increased recently. Marine microalgae are the primary producers of EPA/DHA and promising alternatives for fish oil. Tropical areas have abundant sunlight throughout the year for microalgal cultivation but this practice can be hindered by high temperature. Discovery of heat-tolerant marine microalgae that can synthesize EPA/DHA will solve these problems. A new species of microalga was isolated from a high temperature lagoon and identified as Tetraselmis sp. DS3. These cells could grow at 40 °C, the highest temperature for marine microalgal growth ever reported. Its ω-3 fatty acids and EPA accounted for 33 and 10% of total lipids, respectively, grown in nitrogen-depleted conditions. These cells also accumulated more than 5% β-carotene and 0.48% lutein in biomass. This new microalga can be cultivated for long chain ω-3 fatty acids and lutein production in the tropical areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

Utilization of industrial dairy waste as microalgae cultivation medium : a potential study for sustainable energy resources

NASA Astrophysics Data System (ADS)

Nurmayani, S.; Sugiarti, Y.; Putra, R. H.

2016-04-01

Microalgae is one of biodiesel resources and call as third generation biofuel. Biodiesel is one alternative energy that being developed. So study about resource of biodiesel need a development, for the example is development the basic material such as microalgae. In this paper we explain the potential use of dairy waste from industry as a cultivation medium of microalgae for biodiesel production. Dairy waste from dairy industry contains 34.98% protein, 4.42% lactose, 9.77% fiber, 11.04% fat, 2.33% calcium, 1.05% phosfor, and 0.4 % magnesium, meaning that the dairy waste from dairy industry has a relatively high nutrient content and complete from a source of carbon, nitrogen and phosphorus as macro nutrients. The method in this paper is literature review to resulting a new conclusion about the potency of waste water from dairy industry as microalgae cultivation medium. Based on the study, the dairy waste from dairy industry has potency to be used as cultivation medium of Botryococcus braunii in the production of biodiesel, replacing the conventional cultivation medium.

Pretreated animal and human waste as a substantial nutrient source for cultivation of microalgae for biodiesel production.

PubMed

Kumar, Vinod; Kumar, Akshay; Nanda, Manisha

2018-05-25

The use of human and animal wastes for fertilization of aquaculture ponds has been practiced for thousands of years. In the present work, we have used the excreta (human urine, poultry waste, cow dung, and urine) as a nutrient source for the cultivation of Chlorella singularis, Micractinium pusillum, and Chlorella sorokiniana strains of microalgae. Different solid wastes were treated with 60 mM H 2 SO 4 for the extraction of nutrients. After treatment, the supernatant of different solid wastes and liquid waste were diluted 5, 10, 15, and 20% to be used as a media for the cultivation of microalgae. Chlorella sorokiniana was able to grow in all concentration of excreta media. The maximum growth rate 140 ± 3.1 mg/L/day and lipid production (45.5 ± 2.3 mg/L/day) was obtained in 20% poultry. Among the different excreta media used for cultivation of microalgae, poultry media displayed the best results and thus, should be used for large scale cultivation of microalgae.

Cyanobacteria and microalgae: a renewable source of bioactive compounds and other chemicals.

PubMed

Encarnação, Telma; Pais, Alberto A C C; Campos, Maria G; Burrows, Hugh D

2015-01-01

Microalgae and cyanobacteria are rich sources of many valuable compounds, including important bioactive and biotechnologically relevant chemicals. Their enormous biodiversity, and the consequent variability in the respective biochemical composition, make microalgae cultivations a promising resource for many novel chemically and biologically active molecules and compounds of high commercial value such as lipids and dyes. The nature of the chemicals produced can be manipulated by changing the cultivation media and conditions. Algae are extremely versatile because they can be adapted to a variety of cell culture conditions. They do not require arable land, can be cultivated on saline water and wastewaters, and require much less water than plants. They possess an extremely high growth rate making these microorganisms very attractive for use in biofuel production--some species of algae can achieve around 100 times more oil than oil seeds. In addition, microalgae and cyanobacteria can accumulate various biotoxins and can contribute to mitigate greenhouse gases since they produce biomass through carbon dioxide fixation. In this review, we provide an overview of the application of microalgae in the production of bioactive and other chemicals.

Effects of Selenite on Unicellular Green Microalga Chlorella pyrenoidosa: Bioaccumulation of Selenium, Enhancement of Photosynthetic Pigments, and Amino Acid Production.

PubMed

Zhong, Yu; Cheng, Jay J

2017-12-20

Microalgae were studied as function bioaccumulators of selenium (Se) for food and feed supplement. To investigate the bioaccumulation of Se and its effects on the unicellular green alga Chlorella pyrenoidosa, the algal growth curve, fluorescence parameters, antioxidant enzyme activity, and fatty acid and amino acid profiles were examined. We found that Se at low concentrations (≤40 mg L -1 ) positively promoted algal growth and inhibited lipid peroxidation and intracellular reactive oxygen species. The antioxidative effect was associated with an increase in the levels of glutathione peroxidase, catalase, linolenic acid, and photosynthetic pigments. Meanwhile, a significant increase in amino acid and organic Se content was also detected in the microalgae. In contrast, we found opposite effects in C. pyrenoidosa exposed to >60 mg L -1 Se. The antioxidation and toxicity appeared to be correlated with the bioaccumulation of excess Se. These results provide a better understanding of the effect of Se on green microalgae, which may help in the development of new technological applications for the production of Se-enriched biomass from microalgae.

Extracellular Metabolites from Industrial Microalgae and Their Biotechnological Potential

PubMed Central

Liu, Lu; Pohnert, Georg; Wei, Dong

2016-01-01

Industrial microalgae, as a big family of promising producers of renewable biomass feedstock, have been commercially exploited for functional food, living feed and feed additives, high-value chemicals in nutraceuticals, cosmeceuticals, and chemical reagents. Recently, microalgae have also been considered as a group that might play an important role in biofuel development and environmental protection. Almost all current products of industrial microalgae are derived from their biomass; however, large amounts of spent cell-free media are available from mass cultivation that is mostly unexploited. In this contribution we discuss that these media, which may contain a remarkable diversity of bioactive substances are worthy to be recovered for further use. Obviously, the extracellular metabolites from industrial microalgae have long been neglected in the development of production methods for valuable metabolites. With the advances in the last ten years, more and more structures and properties from extracellular metabolites have been identified, and the potential utilization over wide fields is attracting attention. Some of these extracellular metabolites can be potentially used as drugs, antioxidants, growth regulators or metal chelators. The purpose of this review is to provide an overview of the known extracellular metabolites from industrial microalgae which might be of commercial interest. The attention mainly focuses on the reports of extracellular bioactive metabolites and their potential application in biotechnology. PMID:27775594

Extracellular Metabolites from Industrial Microalgae and Their Biotechnological Potential.

PubMed

Liu, Lu; Pohnert, Georg; Wei, Dong

2016-10-20

Industrial microalgae, as a big family of promising producers of renewable biomass feedstock, have been commercially exploited for functional food, living feed and feed additives, high-value chemicals in nutraceuticals, cosmeceuticals, and chemical reagents. Recently, microalgae have also been considered as a group that might play an important role in biofuel development and environmental protection. Almost all current products of industrial microalgae are derived from their biomass; however, large amounts of spent cell-free media are available from mass cultivation that is mostly unexploited. In this contribution we discuss that these media, which may contain a remarkable diversity of bioactive substances are worthy to be recovered for further use. Obviously, the extracellular metabolites from industrial microalgae have long been neglected in the development of production methods for valuable metabolites. With the advances in the last ten years, more and more structures and properties from extracellular metabolites have been identified, and the potential utilization over wide fields is attracting attention. Some of these extracellular metabolites can be potentially used as drugs, antioxidants, growth regulators or metal chelators. The purpose of this review is to provide an overview of the known extracellular metabolites from industrial microalgae which might be of commercial interest. The attention mainly focuses on the reports of extracellular bioactive metabolites and their potential application in biotechnology.

Cyanobacteria and microalgae: a positive prospect for biofuels.

PubMed

Parmar, Asha; Singh, Niraj Kumar; Pandey, Ashok; Gnansounou, Edgard; Madamwar, Datta

2011-11-01

Biofuel-bioenergy production has generated intensive interest due to increased concern regarding limited petroleum-based fuel supplies and their contribution to atmospheric CO2 levels. Biofuel research is not just a matter of finding the right type of biomass and converting it to fuel, but it must also be economically sustainable on large-scale. Several aspects of cyanobacteria and microalgae such as oxygenic photosynthesis, high per-acre productivity, non-food based feedstock, growth on non-productive and non-arable land, utilization of wide variety of water sources (fresh, brackish, seawater and wastewater) and production of valuable co-products along with biofuels have combined to capture the interest of researchers and entrepreneurs. Currently, worldwide biofuels mainly in focus include biohydrogen, bioethanol, biodiesel and biogas. This review focuses on cultivation and harvesting of cyanobacteria and microalgae, possible biofuels and co-products, challenges for cyanobacterial and microalgal biofuels and the approaches of genetic engineering and modifications to increase biofuel production. Copyright © 2011 Elsevier Ltd. All rights reserved.

Enhancing lutein productivity of an indigenous microalga Scenedesmus obliquus FSP-3 using light-related strategies.

PubMed

Ho, Shih-Hsin; Chan, Ming-Chang; Liu, Chen-Chun; Chen, Chun-Yen; Lee, Wen-Lung; Lee, Duu-Jong; Chang, Jo-Shu

2014-01-01

Lutein, one of the main photosynthetic pigments, is a promising natural product with both nutritional and pharmaceutical applications. In this study, light-related strategies were applied to enhance the cell growth and lutein production of a lutein-rich microalga Scenedesmus obliquus FSP-3. The results demonstrate that using white LED resulted in better lutein production efficiency when compared to the other three monochromatic LEDs (red, blue, and green). The lutein productivity of S. obliquus FSP-3 was further improved by adjusting the type of light source and light intensity. The optimal lutein productivity of 4.08 mg/L/d was obtained when using a TL5 fluorescent lamp at a light intensity of 300 μmol/m(2)/s, and this performance is better than that reported in most related studies. Moreover, the time-course profile of lutein accumulation in the microalga shows that the maximal lutein content and productivity were obtained at the onset of nitrogen depletion. Copyright © 2013 Elsevier Ltd. All rights reserved.

Highly oil-producing microalgae selected through directed-evolution on a microfludic chip

NASA Astrophysics Data System (ADS)

Mestler, Troy; Estevez-Torres, Andre; Lambert, Guillaume; Austin, Robert H.

2009-03-01

Some species of photosynthetic microalgae produce signi?cant amounts of oil which can be easily converted to diesel fuel. However, as it stands today, biodiesel is signi?cantly more expensive than fossil fuels. We wish to improve the oil yield and production rate of a single species of microalgae through directed evolution. We propose to utilize our microfabication technology to create microhabitats to control the nutrient environment of the species, monitor oil production through Raman Spectroscopy, and punish colonies of algae which have low oil yield. We believe this process will produce a mutant species with a high oil yield.

Incorporation of Chlorella vulgaris and Spirulina maxima biomass in pasta products. Part 1: Preparation and evaluation.

PubMed

Fradique, Mónica; Batista, Ana Paula; Nunes, M Cristiana; Gouveia, Luísa; Bandarra, Narcisa M; Raymundo, Anabela

2010-08-15

Microalgae are able to enhance the nutritional content of conventional foods and hence to positively affect human health, due to their original chemical composition. The aim of the present study was to prepare fresh spaghetti enriched with different amounts of microalgae biomass (Chlorella vulgaris and Spirulina maxima) and to compare the quality parameters (optimal cooking time, cooking losses, swelling index and water absorption), chemical composition, instrumental texture and colour of the raw and cooked pasta enriched with microalgae biomass with standard semolina spaghetti. The incorporation of microalgae results in an increase of quality parameters when compared to the control sample. The colour of microalgae pastas remained relatively stable after cooking. The addition of microalgae resulted in an increase in the raw pasta firmness when compared to the control sample. Of all the microalgae studied, an increase in the biomass concentration (0.5-2.0%) resulted in a general tendency of an increase in the pasta firmness. Sensory analysis revealed that microalgae pastas had higher acceptance scores by the panellists than the control pasta. Microalgae pastas presented very appellative colours, such as orange and green, similar to pastas produced with vegetables, with nutritional advantages, showing energetic values similar to commercial pastas. The use of microalgae biomass can enhance the nutritional and sensorial quality of pasta, without affecting its cooking and textural properties. Copyright (c) 2010 Society of Chemical Industry.

Effect of Organic Solvents on Microalgae Growth, Metabolism and Industrial Bioproduct Extraction: A Review.

PubMed

Miazek, Krystian; Kratky, Lukas; Sulc, Radek; Jirout, Tomas; Aguedo, Mario; Richel, Aurore; Goffin, Dorothee

2017-07-04

In this review, the effect of organic solvents on microalgae cultures from molecular to industrial scale is presented. Traditional organic solvents and solvents of new generation-ionic liquids (ILs), are considered. Alterations in microalgal cell metabolism and synthesis of target products (pigments, proteins, lipids), as a result of exposure to organic solvents, are summarized. Applications of organic solvents as a carbon source for microalgal growth and production of target molecules are discussed. Possible implementation of various industrial effluents containing organic solvents into microalgal cultivation media, is evaluated. The effect of organic solvents on extraction of target compounds from microalgae is also considered. Techniques for lipid and carotenoid extraction from viable microalgal biomass (milking methods) and dead microalgal biomass (classical methods) are depicted. Moreover, the economic survey of lipid and carotenoid extraction from microalgae biomass, by means of different techniques and solvents, is conducted.

Thermogravimetric analysis of the gasification of microalgae Chlorella vulgaris.

PubMed

Figueira, Camila Emilia; Moreira, Paulo Firmino; Giudici, Reinaldo

2015-12-01

The gasification of microalgae Chlorella vulgaris under an atmosphere of argon and water vapor was investigated by thermogravimetric analysis. The data were interpreted by using conventional isoconversional methods and also by the independent parallel reaction (IPR) model, in which the degradation is considered to happen individually to each pseudo-component of biomass (lipid, carbohydrate and protein). The IPR model allows obtaining the kinetic parameters of the degradation reaction of each component. Three main stages were observed during the gasification process and the differential thermogravimetric curve was satisfactorily fitted by the IPR model considering three pseudocomponents. The comparison of the activation energy values obtained by the methods and those found in the literature for other microalgae was satisfactory. Quantification of reaction products was performed using online gas chromatography. The major products detected were H2, CO and CH4, indicating the potential for producing fuel gas and syngas from microalgae. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of Organic Solvents on Microalgae Growth, Metabolism and Industrial Bioproduct Extraction: A Review

PubMed Central

Miazek, Krystian; Sulc, Radek; Jirout, Tomas; Aguedo, Mario; Goffin, Dorothee

2017-01-01

In this review, the effect of organic solvents on microalgae cultures from molecular to industrial scale is presented. Traditional organic solvents and solvents of new generation-ionic liquids (ILs), are considered. Alterations in microalgal cell metabolism and synthesis of target products (pigments, proteins, lipids), as a result of exposure to organic solvents, are summarized. Applications of organic solvents as a carbon source for microalgal growth and production of target molecules are discussed. Possible implementation of various industrial effluents containing organic solvents into microalgal cultivation media, is evaluated. The effect of organic solvents on extraction of target compounds from microalgae is also considered. Techniques for lipid and carotenoid extraction from viable microalgal biomass (milking methods) and dead microalgal biomass (classical methods) are depicted. Moreover, the economic survey of lipid and carotenoid extraction from microalgae biomass, by means of different techniques and solvents, is conducted. PMID:28677659

Regulation of Oil Biosynthesis in Algae

DTIC Science & Technology

2014-10-06

renewed interest in microalgae as potential feed stock for renewable fuels including high energy density aviation fuels. Microalgae accumulate large...mechanisms of TAG accumulation relevant to other microalgae and perhaps dedicated biofuel crop plants. Knowledge and understanding of algal model systems...energy density liquid fuels. Long Term Objectives. Under permissive conditions, i.e. nutrient deprivation, many microalgae accumulate oils (TAGs

Composition and Structure of Microalgae Indicated in Raman and Hyperspectral Spectra and Scanning Electron Microscopy: from Cyanobacteria to Isolates from Coal-bed Methane Water Ponds

NASA Astrophysics Data System (ADS)

Zhou, X.; Zhou, Z.; Apple, M. E.; Spangler, L.

2017-12-01

Microalgae can be used for many potential applications for human's benefits. These potential applications included biofuel production from microalgae, biofiltering to cleaning water, chemical extraction as nutrients, etc. However, exploration for such applications is still in the early stages. For instance, many species and strains of microalgae have been investigated for their lipid content and growing conditions for efficient productions of lipids, but no specific species have yet been chosen as a fuel source for commercial production because of the huge biodiversity and subsequently a wide range of species that can potentially be exploited for biodiesel production, the great variability between species in their fuel precursor producing capabilities. Numerous coal-bed methane water ponds were established in the world as a consequence of coal-bed methane production from deep coal seams. Microalgae were isolated from such ponds and potentially these ponds can be used as venues for algal production. In this study, we characterized chemical composition and structure of the Cyanobacteria Anabaena cylindrica (UTEX # 1611) and isolates from coal-bed methane ponds Nannochloropsis gaditana and PW95 using Laser Raman Spectroscopy (LRS), hyperspectral spectra, and Scanning Electron Microscope (SEM). The objective is to seek bio-indicators for potential applications of these microalgae species. For instance, indicator of rich content lips shows the great potential for biofuel production. Fig.1 shows an example of the Raman spectra of the three species in desiccated form. The spectral peaks were isolated and the corresponding composition was identified. The insert at the right hand of the Raman spectrum of each species is the micrograph of the cell morphology under a microscope. The Raman spectra of cells in aquatic solutions were also obtained and compared with the desiccated form. The hyperspectral reflectances of the three species show quite different characteristics and the main absorption bands and scattering bands were located and their association with composition and structure were analyzed and discussed. SEM micrographs will be collected and the composition and structure derived from the SEM micrographs will be discussed and compared with those derived from the Raman spectra and hyperspectral spectra.

Lipid metabolism in response to individual short chain fatty acids during mixotrophic mode of microalgal cultivation: Influence on biodiesel saturation and protein profile.

PubMed

Chandra, Rashmi; Arora, Somya; Rohit, M V; Venkata Mohan, S

2015-01-01

Critical influence of different short chain fatty acids as organic carbon source, during growth (GP) and nutrient stress lipogenic phase (NSLP) was investigated on biomass and lipid productivity, in mixotrophic fed-batch microalgae cultivation. Nutrient deprivation induced physiological stress stimulated highest lipid productivity with acetate (total/neutral lipids, 35/17) with saturation index of 80.53% by the end of NSLP followed by butyrate (12/7%; 78%). Biomass growth followed the order of acetate (2.23 g/l) >butyrate (0.99 g/l) >propionate (0.77 g/l). VFA removal (as COD) was maximum with acetate (87%) followed by butyrate (55.09%) and propionate (10.60%). Palmitic acid was the most dominant fatty acid found in the fatty acid composition of all variants and butyrate fed system yielded a maximum of 44% palmitic acid. Protein profiling illustrated prominence of acetyl CoA-synthetase activity in acetate system. Thus, fatty acids provide a promising alternative feedstock for biodiesel production with integrated microalgae-biorefinery. Copyright © 2015 Elsevier Ltd. All rights reserved.

Impact of inorganic contaminants on microalgae productivity and bioremediation potential.

PubMed

Torres, Eric M; Hess, Derek; McNeil, Brian T; Guy, Tessa; Quinn, Jason C

2017-05-01

As underdeveloped nations continue to industrialize and world population continues to increase, the need for energy, natural resources, and goods will lead to ever increasing inorganic contaminants, such as heavy metals, in various waste streams that can have damaging effects on plant life, wildlife, and human health. This work is focused on the evaluation of the potential of Nannochloropsis salina to be integrated with contaminated water sources for the concurrent production of a biofuel feedstock while providing an environmental service through bioremediation. Individual contaminants (As, Cd, Cr, Co, Cu, Pb, Ni, Hg, Se, and Zn) at various concentrations ranging from a low concentration (1X) to higher concentrations (10X, and 40X) found in contaminated systems (mine tailings, wastewater treatment plants, produced water) were introduced into growth media. Biological growth experimentation was performed in triplicate at the various contaminant concentrations and at 3 different light intensities. Results show that baseline concentrations of each contaminant slightly decreased biomass growth to between 89% and 99% of the control with the exception of Ni which dramatically reduced growth. Increased contaminant concentrations resulted in progressively lower growth rates for all contaminants tested. Lipid analysis shows most baseline contaminant concentrations slightly decrease or have minimal effects on lipid content at all light levels. Trace contaminant analysis on the biomass showed Cd, Co, Cu, Pb, and Zn were sorbed by the microalgae with minimal contaminants remaining in the growth media illustrating the effectiveness of microalgae to bioremediate these contaminants when levels are sufficiently low to not detrimentally impact productivity. The microalgae biomass was less efficient at sorption of As, Cr, Ni, and Se. Copyright © 2017 Elsevier Inc. All rights reserved.

Development of a floating photobioreactor with internal partitions for efficient utilization of ocean wave into improved mass transfer and algal culture mixing.

PubMed

Kim, Z-Hun; Park, Hanwool; Hong, Seong-Joo; Lim, Sang-Min; Lee, Choul-Gyun

2016-05-01

Culturing microalgae in the ocean has potentials that may reduce the production cost and provide an option for an economic biofuel production from microalgae. The ocean holds great potentials for mass microalgal cultivation with its high specific heat, mixing energy from waves, and large cultivable area. Suitable photobioreactors (PBRs) that are capable of integrating marine energy into the culture systems need to be developed for the successful ocean cultivation. In this study, prototype floating PBRs were designed and constructed using transparent low-density polyethylene film for microalgal culture in the ocean. To improve the mixing efficiency, various types of internal partitions were introduced within PBRs. Three different types of internal partitions were evaluated for their effects on the mixing efficiency in terms of mass transfer (k(L)a) and mixing time in the PBRs. The partition type with the best mixing efficiency was selected, and the number of partitions was varied from one to three for investigation of its effect on mixing efficiency. When the number of partitions is increased, mass transfer increased in proportion to the number of partitions. However, mixing time was not directly related to the number of partitions. When a green microalga, Tetraselmis sp. was cultivated using PBRs with the selected partition under semi-continuous mode in the ocean, biomass and fatty acid productivities in the PBRs were increased by up to 50 % and 44% at high initial cell density, respectively, compared to non-partitioned ones. The results of internally partitioned PBRs demonstrated potentials for culturing microalgae by efficiently utilizing ocean wave energy into culture mixing in the ocean.

Enhancement of lipid production in two marine microalgae under different levels of nitrogen and phosphorus deficiency.

PubMed

Adenan, Nurul Salma; Yusoff, Fatimah Md; Medipally, Srikanth Reddy; Shariff, M

2016-07-01

Microalgae are important food sources for aquaculture animals. Among the different factors which influence the biochemical composition of microalgae, nitrogen and phosphorus are two of the most important nutrient sources for growth and development. The present study aimed to assess the effects of nitrogen and phosphorus deficiency on lipid production of Chlorella sp. and Chaetoceros calcitrans. Early stationary phase culture of these species were exposed to different stress levels of nitrogen and phosphorus (25%, 50% and 75% of the full NO(3)-N and PO(4)-P concentration in the Conway media), and solvent extraction and gas-liquid chromatography methods were performed for analysis of lipid and fatty acid composition. The results revealed that lipid production in these two species significantly increased (P<0.05) as nitrogen and phosphorus decreased. The fatty acid proportion remained unaffected under nitrogen deficiency, while phosphorus limitation resulted in a decrease of saturated fatty acids and promoted a higher content of omega-3 fatty acids in these species. The protein and carbohydrate levels were also altered under limited nutrients. Therefore, these conditions could be used for enhanced lipid production in microalgae for aquaculture and other industrial applications.

Strain selection of microalgae isolated from Tunisian coast: characterization of the lipid profile for potential biodiesel production.

PubMed

Gnouma, Asma; Sehli, Emna; Medhioub, Walid; Ben Dhieb, Rym; Masri, Mahmoud; Mehlmer, Norbert; Slimani, Wissem; Sebai, Khaled; Zouari, Amel; Brück, Thomas; Medhioub, Amel

2018-06-26

Microalgae could be of importance for future biodiesel production as an alternative for a third generation of biofuels. To select the most appropriate strain for biodiesel production, three microalgae species, namely Isochrysis sp., Nannochloropsis maritima and Tetraselmis sp., isolated from Tunisian coast, were biochemically characterized. Initially, gas chromatography analysis showed that Isochrysis sp. and N. maritima contained 5- and 10-fold total fatty acids, respectively, more than Tetraselmis sp. Then, the two microalgae Isochrysis sp. and N. maritima were subject to random mutagenesis using ultraviolet-C radiation. Subsequently, a total of 18 mutants were obtained from both species. The neutral lipid evaluation on said 18 mutants allowed the retention of only 7 to further fatty acid characterization. Finally, gas chromatography revealed that the mutant 5c Isochrysis sp. was characterized by a high level of saturated fatty acids (52.3%), higher amount of monounsaturated fatty acids (29.3%), lower level of polyunsaturated fatty acids (18.4%) and a significant 1.3-fold increase in its C16-C18 content compared to the wild-type strain, which would make it an interesting candidate for biofuel production.

Modelling of microalgal growth and lipid production in Dunaliella tertiolecta using nitrogen-phosphorus-potassium fertilizer medium in sintered disk chromatographic glass bubble column.

PubMed

Kumar, Anup; Guria, Chandan; Chitres, G; Chakraborty, Arunangshu; Pathak, A K

2016-10-01

A comprehensive mathematical model involving NPK-10:26:26 fertilizer, NaCl, NaHCO3, light and temperature operating variables for Dunaliella tertiolecta cultivation is formulated to predict microalgae-biomass and lipid productivity. Proposed model includes Monod/Andrews kinetics for the absorption of essential nutrients into algae-biomass and Droop model involving internal nutrient cell quota for microalgae growth, assuming algae-biomass is composed of sugar, functional-pool and neutral-lipid. Biokinetic model parameters are determined by minimizing the residual-sum-of-square-errors between experimental and computed microalgae-biomass and lipid productivity using genetic algorithm. Developed model is validated with the experiments of Dunaliella tertiolecta cultivation using air-agitated sintered-disk chromatographic glass-bubble column and the effects of operating variables on microalgae-biomass and lipid productivity is investigated. Finally, parametric sensitivity analysis is carried out to know the sensitivity of model parameters on the obtained results in the input parameter space. Proposed model may be helpful in scale-up studies and implementation of model-based control strategy in large-scale algal cultivation. Copyright © 2016 Elsevier Ltd. All rights reserved.

De Novo Transcriptomic Analysis of an Oleaginous Microalga: Pathway Description and Gene Discovery for Production of Next-Generation Biofuels

PubMed Central

Wan, LingLin; Han, Juan; Sang, Min; Li, AiFen; Wu, Hong; Yin, ShunJi; Zhang, ChengWu

2012-01-01

Background Eustigmatos cf. polyphem is a yellow-green unicellular soil microalga belonging to the eustimatophyte with high biomass and considerable production of triacylglycerols (TAGs) for biofuels, which is thus referred to as an oleaginous microalga. The paucity of microalgae genome sequences, however, limits development of gene-based biofuel feedstock optimization studies. Here we describe the sequencing and de novo transcriptome assembly for a non-model microalgae species, E. cf. polyphem, and identify pathways and genes of importance related to biofuel production. Results We performed the de novo assembly of E. cf. polyphem transcriptome using Illumina paired-end sequencing technology. In a single run, we produced 29,199,432 sequencing reads corresponding to 2.33 Gb total nucleotides. These reads were assembled into 75,632 unigenes with a mean size of 503 bp and an N50 of 663 bp, ranging from 100 bp to >3,000 bp. Assembled unigenes were subjected to BLAST similarity searches and annotated with Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) orthology identifiers. These analyses identified the majority of carbohydrate, fatty acids, TAG and carotenoids biosynthesis and catabolism pathways in E. cf. polyphem. Conclusions Our data provides the construction of metabolic pathways involved in the biosynthesis and catabolism of carbohydrate, fatty acids, TAG and carotenoids in E. cf. polyphem and provides a foundation for the molecular genetics and functional genomics required to direct metabolic engineering efforts that seek to enhance the quantity and character of microalgae-based biofuel feedstock. PMID:22536352

Techno-economical evaluation of protein extraction for microalgae biorefinery

NASA Astrophysics Data System (ADS)

Sari, Y. W.; Sanders, J. P. M.; Bruins, M. E.

2016-01-01

Due to scarcity of fossil feedstocks, there is an increasing demand for biobased fuels. Microalgae are considered as promising biobased feedstocks. However, microalgae based fuels are not yet produced at large scale at present. Applying biorefinery, not only for oil, but also for other components, such as carbohydrates and protein, may lead to the sustainable and economical microalgae-based fuels. This paper discusses two relatively mild conditions for microalgal protein extraction, based on alkali and enzymes. Green microalgae (Chlorella fusca) with and without prior lipid removal were used as feedstocks. Under mild conditions, more protein could be extracted using proteases, with the highest yields for microalgae meal (without lipids). The data on protein extraction yields were used to calculate the costs for producing 1 ton of microalgal protein. The processing cost for the alkaline method was € 2448 /ton protein. Enzymatic method performed better from an economic point of view with € 1367 /ton protein on processing costs. However, this is still far from industrially feasible. For both extraction methods, biomass cost per ton of produced product were high. A higher protein extraction yield can partially solve this problem, lowering processing cost to €620 and 1180 /ton protein product, using alkali and enzyme, respectively. Although alkaline method has lower processing cost, optimization appears to be better achievable using enzymes. If the enzymatic method can be optimized by lowering the amount of alkali added, leading to processing cost of € 633/ton protein product. Higher revenue can be generated when the residue after protein extraction can be sold as fuel, or better as a highly digestible feed for cattle.

Nutrients recycling strategy for microalgae-based CO2 mitigation system

NASA Astrophysics Data System (ADS)

E, Xinyi

Coal-fired electricity production is the major emitter of CO2 and other greenhouse gases including NOx and SO x. Microalgae-based CO2 mitigation systems have been proposed to reduce the net CO2 emission from coal-fired power plants. This study focused on developing an optimum culture media and exploring the possibilities for recycling nutrients, which were added as commercial mineralized chemicals at the beginning of cultivation. In order to release the nutrients embedded in the cells so that they can be used as a nutrient source for new cells, Scenedesmus biomass was digested by anaerobic bacteria. Results showed that thermal pretreatment enhanced the methane production rate for the first 7 days of digestion. Three operational factors were tested: heating temperature, heating duration and NaOH dosage. The combination of 10 min heating with 3˜6% NaOH at 50 °C gave the highest cell wall destruction for all samples except oven-dried algae. The anaerobic digestate, rich in mineralized nutrients including ammonium and phosphate, potassium and magnesium ions, was tested as a possible nutrient source for the algae cultivation. To cope with the high solid content of the digestates, the dosage of the digestates was reduced or the solid particles were removed prior to addition to the microalgae. Both approaches worked well in terms of providing nutrients with minimal effect on light penetration. Using digestates without any sterilization did not cause contamination or other deleterious effects on the Scenedesmus growth rate. Harvesting microalgae cells was critical to ensure a continuous and robust growth rate. The used media could be recycled at least four times without altering the algae growth. Nutrient replenishment was the key for a healthy culture when used media was incorporated. The combination of used media and digestates can sustain a normal algae growth. Life cycle assessment was conducted on the system including the photobioreactor, the anaerobic digester, the biomass settling and dewatering and used media and nutrient recycling. Considering methane as the energy source, the overall energy return of the system was 2.4. CO2 mitigation rate was about 39% under current mitigation system. KEYWORDS: Scenedesmus, urea, anaerobic digestion, used media, life cycle assessment.

Lipid production from tapioca wastewater by culture of Scenedesmus sp. with simultaneous BOD, COD and nitrogen removal

NASA Astrophysics Data System (ADS)

Romaidi; Hasanudin, Muhammad; Kholifah, Khusnul; Maulidiyah, Alik; Putro, Sapto P.; Kikuchi, Akira; Sakaguchi, Toshifumi

2018-05-01

The use of microalgae to produce biodiesel or possibly remove nutrients from industrial wastewater has gained important attention during recent years due to their photosynthetic rate and its versatile nature to grow in various wastewater systems. In this study, a microalgae, Scenedesmus sp., was cultured to enhance the lipid production and nutrients removal from tapioca wastewater sample. To assess lipid production, Scenedesmus sp. was cultured in different concentration of tapioca wastewater sample (from 0 to 100 %), and nutrient removal including BOD, COD, NH4, NO2, NO3 level by Scenedesmus sp. was assessed in 100% of tapioca wastewater culture. After 8 days of culture, it was found out that 50% of tapioca wastewater sample resulted in highest concentration of lipid content than that of the other concentrations. The level of environment indicator as nutrient removal such as BOD, COD, NH4, NO2, NO3 were also decreased up to 74%, 72%, 95%, 91%, and 91%, respectively. The pH condition changed from initial condition acidic (pH: 4) to neutral or basic condition (pH: 7-8) as recommended in wastewater treatment system. This research provided a novel approach and achieved efficient simultaneous lipid production and nutrients removal from tapioca wastewater sample by Scenedesmus’s culture system.

Flotation of algae for water reuse and biomass production: role of zeta potential and surfactant to separate algal particles.

PubMed

Kwak, Dong-Heui; Kim, Mi-Sug

2015-01-01

The effect of chemical coagulation and biological auto-flocculation relative to zeta potential was examined to compare flotation and sedimentation separation processes for algae harvesting. Experiments revealed that microalgae separation is related to auto-flocculation of Anabaena spp. and requires chemical coagulation for the whole period of microalgae cultivation. In addition, microalgae separation characteristics which are associated with surfactants demonstrated optimal microalgae cultivation time and separation efficiency of dissolved CO2 flotation (DCF) as an alternative to dissolved air flotation (DAF). Microalgae were significantly separated in response to anionic surfactant rather than cationic surfactant as a function of bubble size and zeta potential. DAF and DCF both showed slightly efficient flotation; however, application of anionic surfactant was required when using DCF.

Biologically Active Metabolites Synthesized by Microalgae

PubMed Central

Costa, Jorge Alberto Vieira

2015-01-01

Microalgae are microorganisms that have different morphological, physiological, and genetic traits that confer the ability to produce different biologically active metabolites. Microalgal biotechnology has become a subject of study for various fields, due to the varied bioproducts that can be obtained from these microorganisms. When microalgal cultivation processes are better understood, microalgae can become an environmentally friendly and economically viable source of compounds of interest, because production can be optimized in a controlled culture. The bioactive compounds derived from microalgae have anti-inflammatory, antimicrobial, and antioxidant activities, among others. Furthermore, these microorganisms have the ability to promote health and reduce the risk of the development of degenerative diseases. In this context, the aim of this review is to discuss bioactive metabolites produced by microalgae for possible applications in the life sciences. PMID:26339647

Mutation Breeding of Extracellular Polysaccharide-Producing Microalga Crypthecodinium cohnii by a Novel Mutagenesis with Atmospheric and Room Temperature Plasma

PubMed Central

Liu, Bin; Sun, Zheng; Ma, Xiaonian; Yang, Bo; Jiang, Yue; Wei, Dong; Chen, Feng

2015-01-01

Extracellular polysaccharides (EPS) produced by marine microalgae have the potential to be used as antioxidants, antiviral agents, immunomodulators, and anti-inflammatory agents. Although the marine microalga Crypthecodinium cohnii releases EPS during the process of docosahexaenoic acid (DHA) production, the yield of EPS remains relatively low. To improve the EPS production, a novel mutagenesis of C. cohnii was conducted by atmospheric and room temperature plasma (ARTP). Of the 12 mutants obtained, 10 mutants exhibited significantly enhanced EPS yield on biomass as compared with the wild type strain. Among them, mutant M7 was the best as it could produce an EPS volumetric yield of 1.02 g/L, EPS yield on biomass of 0.39 g/g and EPS yield on glucose of 94 mg/g, which were 33.85%, 85.35% and 57.17% higher than that of the wild type strain, respectively. Results of the present study indicated that mutagenesis of the marine microalga C. cohnii by ARTP was highly effective leading to the high-yield production of EPS. PMID:25872142

Continuous production of biodiesel from microalgae by extraction coupling with transesterification under supercritical conditions.

PubMed

Zhou, Dan; Qiao, Baoquan; Li, Gen; Xue, Song; Yin, Jianzhong

2017-08-01

Raw material for biodiesel has been expanded from edible oil to non-edible oil. In this study, biodiesel continuous production for two kinds of microalgae Chrysophyta and Chlorella sp. was conducted. Coupling with the supercritical carbon dioxide extraction, the oil of microalgae was extracted firstly, and then sent to the downstream production of biodiesel. The residue after decompression can be reused as the material for pharmaceuticals and nutraceuticals. Results showed that the particle size of microalgae, temperature, pressure, molar ration of methanol to oil, flow of CO 2 and n-hexane all have effects on the yield of biodiesel. With the optimal operation conditions: 40mesh algae, extraction temperature 60°C, flow of n-hexane 0.4ml/min, reaction temperature: 340°C, pressure: 18-20MPa, CO 2 flow of 0.5L/min, molar ration of methanol to oil 84:1, a yield of 56.31% was obtained for Chrysophyta, and 63.78% for Chlorella sp. due to the higher lipid content. Copyright © 2017. Published by Elsevier Ltd.

Microalgae Cultivation on Anaerobic Digestate of Municipal Wastewater, Sewage Sludge and Agro-Waste.

PubMed

Zuliani, Luca; Frison, Nicola; Jelic, Aleksandra; Fatone, Francesco; Bolzonella, David; Ballottari, Matteo

2016-10-10

Microalgae are fast-growing photosynthetic organisms which have the potential to be exploited as an alternative source of liquid fuels to meet growing global energy demand. The cultivation of microalgae, however, still needs to be improved in order to reduce the cost of the biomass produced. Among the major costs encountered for algal cultivation are the costs for nutrients such as CO₂, nitrogen and phosphorous. In this work, therefore, different microalgal strains were cultivated using as nutrient sources three different anaerobic digestates deriving from municipal wastewater, sewage sludge or agro-waste treatment plants. In particular, anaerobic digestates deriving from agro-waste or sewage sludge treatment induced a more than 300% increase in lipid production per volume in Chlorella vulgaris cultures grown in a closed photobioreactor, and a strong increase in carotenoid accumulation in different microalgae species. Conversely, a digestate originating from a pilot scale anaerobic upflow sludge blanket (UASB) was used to increase biomass production when added to an artificial nutrient-supplemented medium. The results herein demonstrate the possibility of improving biomass accumulation or lipid production using different anaerobic digestates.

Combining micro-structures and micro-algae to increase lipid production for bio-fuel

NASA Astrophysics Data System (ADS)

Vyawahare, Saurabh; Zhu, Emilly; Mestler, Troy; Estévez-Torres, André.; Austin, Robert

2011-03-01

3rd generation bio-fuels like lipid producing micro-algae are a promising source of energy that could replace our dependence on petroleum. However, until there are improvements in algae oil yields, and a reduction in the energy needed for processing, algae bio-fuels are not economically competitive with petroleum. Here, we describe our work combining micro-fabricated devices with micro-algae Neochloris oleoabundans, a species first isolated on the sand dunes of Saudi Arabia. Inserting micro-algae of varying fitness into a landscape of micro-habitats allows us to evolve and select them based on a variety of conditions like specific gravity, starvation response and Nile Red fluorescence (which is a marker for lipid production). Hence, we can both estimate the production of lipids and generate conditions that allow the creation and isolation of algae which produce higher amounts of lipids, while discarding the rest. Finally, we can use micro-fabricated structures and flocculation to de-water these high lipid producing algae, reducing the need for expensive centrifugation and filtration.

Chemicals to enhance microalgal growth and accumulation of high-value bioproducts

PubMed Central

Yu, Xinheng; Chen, Lei; Zhang, Weiwen

2015-01-01

Photosynthetic microalgae have attracted significant attention as they can serve as important sources for cosmetic, food and pharmaceutical products, industrial materials and even biofuel biodiesels. However, current productivity of microalga-based processes is still very low, which has restricted their scale-up application. In addition to various efforts in strain improvement and cultivation optimization, it was proposed that the productivity of microalga-based processes can also be increased using various chemicals to trigger or enhance cell growth and accumulation of bioproducts. Herein, we summarized recent progresses in applying chemical triggers or enhancers to improve cell growth and accumulation of bioproducts in algal cultures. Based on their enhancing mechanisms, these chemicals can be classified into four categories:chemicals regulating biosynthetic pathways, chemicals inducing oxidative stress responses, phytohormones and analogs regulating multiple aspects of microalgal metabolism, and chemicals directly as metabolic precursors. Taken together, the early researches demonstrated that the use of chemical stimulants could be a very effective and economical way to improve cell growth and accumulation of high-value bioproducts in large-scale cultivation of microalgae. PMID:25741321

Preliminary assessment of Malaysian micro-algae strains for the production of bio jet fuel

NASA Astrophysics Data System (ADS)

Chen, J. T.; Mustafa, E. M.; Vello, V.; Lim, P.; Nik Sulaiman, N. M.; Majid, N. Abdul; Phang, S.; Tahir, P. Md.; Liew, K.

2016-10-01

Malaysia is the main hub in South-East Asia and has one of the highest air traffic movements in the region. Being rich in biodiversity, Malaysia has long been touted as country rich in biodiversity and therefore, attracts great interests as a place to setup bio-refineries and produce bio-fuels such as biodiesel, bio-petrol, green diesel, and bio-jet fuel Kerosene Jet A-1. Micro-algae is poised to alleviate certain disadvantages seen in first generation and second generation feedstock. In this study, the objective is to seek out potential micro-algae species in Malaysia to determine which are suitable to be used as the feedstock to enable bio-jet fuel production in Malaysia. From 79 samples collected over 30 sites throughout Malaysia, six species were isolated and compared for their biomass productivity and lipid content. Their lipid contents were then used to derived the require amount of micro-algae biomass to yield 1 kg of certifiable jet fuel via the HEFA process, and to meet a scenario where Malaysia implements a 2% alternative (bio-) jet fuel requirement.

Microalgae Cultivation on Anaerobic Digestate of Municipal Wastewater, Sewage Sludge and Agro-Waste

PubMed Central

Zuliani, Luca; Frison, Nicola; Jelic, Aleksandra; Fatone, Francesco; Bolzonella, David; Ballottari, Matteo

2016-01-01

Microalgae are fast-growing photosynthetic organisms which have the potential to be exploited as an alternative source of liquid fuels to meet growing global energy demand. The cultivation of microalgae, however, still needs to be improved in order to reduce the cost of the biomass produced. Among the major costs encountered for algal cultivation are the costs for nutrients such as CO2, nitrogen and phosphorous. In this work, therefore, different microalgal strains were cultivated using as nutrient sources three different anaerobic digestates deriving from municipal wastewater, sewage sludge or agro-waste treatment plants. In particular, anaerobic digestates deriving from agro-waste or sewage sludge treatment induced a more than 300% increase in lipid production per volume in Chlorella vulgaris cultures grown in a closed photobioreactor, and a strong increase in carotenoid accumulation in different microalgae species. Conversely, a digestate originating from a pilot scale anaerobic upflow sludge blanket (UASB) was used to increase biomass production when added to an artificial nutrient-supplemented medium. The results herein demonstrate the possibility of improving biomass accumulation or lipid production using different anaerobic digestates. PMID:27735859

Algal Cell Factories: Approaches, Applications, and Potentials.

PubMed

Fu, Weiqi; Chaiboonchoe, Amphun; Khraiwesh, Basel; Nelson, David R; Al-Khairy, Dina; Mystikou, Alexandra; Alzahmi, Amnah; Salehi-Ashtiani, Kourosh

2016-12-13

With the advent of modern biotechnology, microorganisms from diverse lineages have been used to produce bio-based feedstocks and bioactive compounds. Many of these compounds are currently commodities of interest, in a variety of markets and their utility warrants investigation into improving their production through strain development. In this review, we address the issue of strain improvement in a group of organisms with strong potential to be productive "cell factories": the photosynthetic microalgae. Microalgae are a diverse group of phytoplankton, involving polyphyletic lineage such as green algae and diatoms that are commonly used in the industry. The photosynthetic microalgae have been under intense investigation recently for their ability to produce commercial compounds using only light, CO₂, and basic nutrients. However, their strain improvement is still a relatively recent area of work that is under development. Importantly, it is only through appropriate engineering methods that we may see the full biotechnological potential of microalgae come to fruition. Thus, in this review, we address past and present endeavors towards the aim of creating productive algal cell factories and describe possible advantageous future directions for the field.

From lab to full-scale ultrafiltration in microalgae harvesting

NASA Astrophysics Data System (ADS)

Wenten, I. G.; Steven, S.; Dwiputra, A.; Khoiruddin; Hakim, A. N.

2017-07-01

Ponding system is generally used for microalgae cultivation. However, selection of appropriate technology for the harvesting process is challenging due to the low cell density of cultivated microalgae from the ponding system and the large volume of water to be handled. One of the promising technologies for microalgae harvesting is ultrafiltration (UF). In this study, the performance of UF during harvesting of microalgae in a lab- and a full-scale test is investigated. The performances of both scales are compared and analyzed to provide an understanding of several aspects which affect the yield produced from lab and actual conditions. Furthermore, a unique self-standing non-modular UF is introduced in the full-scale test. The non-modular UF exhibits several advantages, such as simple piping and connection, single pump for filtration and backwashing, and smaller footprint. With those advantages, the non-modular UF could be a promising technology for microalgae harvesting in industrial-scale.

Marine Microalgae with Anti-Cancer Properties.

PubMed

Martínez Andrade, Kevin A; Lauritano, Chiara; Romano, Giovanna; Ianora, Adrianna

2018-05-15

Cancer is the leading cause of death globally and finding new therapeutic agents for cancer treatment remains a major challenge in the pursuit for a cure. This paper presents an overview on microalgae with anti-cancer activities. Microalgae are eukaryotic unicellular plants that contribute up to 40% of global primary productivity. They are excellent sources of pigments, lipids, carotenoids, omega-3 fatty acids, polysaccharides, vitamins and other fine chemicals, and there is an increasing demand for their use as nutraceuticals and food supplements. Some microalgae are also reported as having anti-cancer activity. In this review, we report the microalgal species that have shown anti-cancer properties, the cancer cell lines affected by algae and the concentrations of compounds/extracts tested to induce arrest of cell growth. We also report the mediums used for growing microalgae that showed anti-cancer activity and compare the bioactivity of these microalgae with marine anticancer drugs already on the market and in phase III clinical trials. Finally, we discuss why some microalgae can be promising sources of anti-cancer compounds for future development.

Mixotrophic cultivation of Chlorella vulgaris using industrial dairy waste as organic carbon source.

PubMed

Abreu, Ana P; Fernandes, Bruno; Vicente, António A; Teixeira, José; Dragone, Giuliano

2012-08-01

Growth parameters and biochemical composition of the green microalga Chlorella vulgaris cultivated under different mixotrophic conditions were determined and compared to those obtained from a photoautotrophic control culture. Mixotrophic microalgae showed higher specific growth rate, final biomass concentration and productivities of lipids, starch and proteins than microalgae cultivated under photoautotrophic conditions. Moreover, supplementation of the inorganic culture medium with hydrolyzed cheese whey powder solution led to a significant improvement in microalgal biomass production and carbohydrate utilization when compared with the culture enriched with a mixture of pure glucose and galactose, due to the presence of growth promoting nutrients in cheese whey. Mixotrophic cultivation of C. vulgaris using the main dairy industry by-product could be considered a feasible alternative to reduce the costs of microalgal biomass production, since it does not require the addition of expensive carbohydrates to the culture medium. Copyright © 2012 Elsevier Ltd. All rights reserved.

Utilization of organic residues using heterotrophic microalgae and insects.

PubMed

Pleissner, Daniel; Rumpold, Birgit A

2018-02-01

Various organic residues occur globally in the form of straw, wood, green biomass, food waste, feces, manure etc. Other utilization strategies apart from anaerobic digestion, composting and incineration are needed to make use of the whole potential of organic residues as sources of various value added compounds. This review compares the cultivation of heterotrophic microalgae and insects using organic residues as nutrient sources and illuminates their potential with regard to biomass production, productivity and yield, and utilization strategies of produced biomasses. Furthermore, cultivation processes as well as advantages and disadvantages of utilization processes are identified and discussed. It was shown that both heterotrophic algae and insects are able to reduce a sufficient amount of organic residues by converting it into biomass. The biomass composition of both organisms is similar which allows similar utilization strategies in food and feed, chemicals and materials productions. Even though insect is the more complex organism, biomass production can be carried out using simple equipment without sterilization and hydrolysis of organic residues. Contrarily, heterotrophic microalgae require a pretreatment of organic residues in form of sterilization and in most cases hydrolysis. Interestingly, the volumetric productivity of insect biomass exceeds the productivity of algal biomass. Despite legal restrictions, it is expected that microalgae and insects will find application as alternative food and feed sources in the future. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enhancement of astaxanthin production using Haematococcus pluvialis with novel LED wavelength shift strategy.

PubMed

Xi, Tianqi; Kim, Dae Geun; Roh, Seong Woon; Choi, Jong-Soon; Choi, Yoon-E

2016-07-01

Haematococcus pluvialis is a green microalga of particular interest, since it is considered the best potential natural source of astaxanthin, which is widely used as an additive for natural pigmentation. In addition, astaxanthin has recently garnered commercial interest as a nutraceutical, cosmetic, and pharmaceutical. However, producing astaxanthin from H. pluvialis necessitates separation with distinctive culture conditions, dividing between the microalgae growth and the astaxanthin production stages. Light-emitting diodes (LEDs) have emerged as a replacement for traditional light sources, and LED applications are now rapidly expanding to multiple areas in fields such as biotechnology. However, further detail application into microalgae biotechnology remains limited. In this study, we have attempted to establish new protocols based on the specific wavelength of LEDs for the cultivation and production of astaxanthin using H. pluvialis. Specifically, we applied red LEDs for microalgae cell growth and then switched to blue LEDs to induce astaxanthin biosynthesis. The result showed that astaxanthin productions based on a wavelength shift from red to blue were significantly increased, compared to those with continuous illumination using red LEDs. Furthermore, additional increase of astaxanthin production was achieved with simultaneous application of exogenous carbon with blue LED illumination. Our approach based on the proper manipulation of LED wavelengths upon H. pluvialis cell stages will enable the improvement of biomass and enhance astaxanthin production using H. pluvialis.

A droplet microfluidics platform for rapid microalgal growth and oil production analysis.

PubMed

Kim, Hyun Soo; Guzman, Adrian R; Thapa, Hem R; Devarenne, Timothy P; Han, Arum

2016-08-01

Microalgae have emerged as a promising source for producing future renewable biofuels. Developing better microalgal strains with faster growth and higher oil production rates is one of the major routes towards economically viable microalgal biofuel production. In this work, we present a droplet microfluidics-based microalgae analysis platform capable of measuring growth and oil content of various microalgal strains with single-cell resolution in a high-throughput manner. The platform allows for encapsulating a single microalgal cell into a water-in-oil emulsion droplet and tracking the growth and division of the encapsulated cell over time, followed by on-chip oil quantification. The key feature of the developed platform is its capability to fluorescently stain microalgae within microdroplets for oil content quantification. The performance of the developed platform was characterized using the unicellular microalga Chlamydomonas reinhardtii and the colonial microalga Botryococcus braunii. The application of the platform in quantifying growth and oil accumulation was successfully confirmed using C. reinhardtii under different culture conditions, namely nitrogen-replete and nitrogen-limited conditions. These results demonstrate the capability of this platform as a rapid screening tool that can be applied to a wide range of microalgal strains for analyzing growth and oil accumulation characteristics relevant to biofuel strain selection and development. Biotechnol. Bioeng. 2016;113: 1691-1701. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Improving protein production of indigenous microalga Chlorella vulgaris FSP-E by photobioreactor design and cultivation strategies.

PubMed

Chen, Chun-Yen; Lee, Po-Jen; Tan, Chung Hong; Lo, Yung-Chung; Huang, Chieh-Chen; Show, Pau Loke; Lin, Chih-Hung; Chang, Jo-Shu

2015-06-01

Fish meal is currently the major protein source for commercial aquaculture feed. Due to its unstable supply and increasing price, fish meal is becoming more expensive and its availability is expected to face significant challenges in the near future. Therefore, feasible alternatives to fish meal are urgently required. Microalgae have been recognized as the most promising candidates to replace fish meal because the protein composition of microalgae is similar to fish meal and the supply of microalgae-based proteins is sustainable. In this study, an indigenous microalga (Chlorella vulgaris FSP-E) with high protein content was selected, and its feasibility as an aquaculture protein source was explored. An innovative photobioreactor (PBR) utilizing cold cathode fluorescent lamps as an internal light source was designed to cultivate the FSP-E strain for protein production. This PBR could achieve a maximum biomass and protein productivity of 699 and 365 mg/L/day, respectively, under an optimum urea and iron concentration of 12.4 mM and 90 μM, respectively. In addition, amino acid analysis of the microalgal protein showed that up to 70% of the proteins in this microalgal strain consist of indispensable amino acids. Thus, C. vulgaris FSP-E appears to be a viable alternative protein source for the aquaculture industry. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

FY 1987 Aquatic Species Program: Annual report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, D.A.; Sprague, S.

The goal of the Department of Energy/Solar Energy Research Institute Aquatic Species Program is to develop the technology base to produce liquid fuels from microalagae at prices competitive with conventional alternatives. Microalgae are unusual plants that can accumulate large quantities of oil and can thrive in high-salinity water, which currently has no competing uses. The algal oils, in turn, are readily converted into gasoline and diesel fuels. The best site for successful microalgae production was determined to be the US desert Southwest, with potential applications to other warm areas. Aggressive research is needed, but the improvements required are attainable. Themore » four prime research areas in the development of this technology are growth and production, engineering design, harvesting, and conversion. Algae are selected for three criteria: tolerance to environmental fluctuations, high growth rates, and high lipid production. From 1982 to 1986, the program collected more than 3000 strains of microalgae that are more than twice as tolerant to temperature and salinity fluctuation than the initial strains. Productivity has been increased by a factor of two in outdoor culture systems since 1982, and lipid content has also been increased from 20% of body weight in 1982 to greater than 66% of body weight in 1987. Research programs are ongoing in lipid biochemistry and genetic engineering so that ultimately strains can be modified and improved to combine their best characteristics. An outdoor test facility is being built in Roswell, New Mexico.« less

Engineering The Unicellular Alga Phaeodactylum tricornutum For High-Value Plant Triterpenoid Production.

PubMed

D'Adamo, Sarah; Schiano di Visconte, Gino; Lowe, Gavin; Szaub-Newton, Joanna; Beacham, Tracey; Landels, Andrew; Allen, Michael J; Spicer, Andrew; Matthijs, Michiel

2018-05-13

Plant triterpenoids constitute a diverse class of organic compounds that play a major role in development, plant defense and environmental interaction. Several triterpenes have demonstrated potential as pharmaceuticals. One example is betulin, which has shown promise as a pharmaceutical precursor for the treatment of certain cancers and HIV. Major challenges for triterpenoid commercialization include their low production levels and their cost-effective purification from the complex mixtures present in their natural hosts. Therefore, attempts to produce these compounds in industrially relevant microbial systems such as bacteria and yeasts have attracted great interest. Here we report the production of the triterpenes betulin and its precursor lupeol in the photosynthetic diatom Phaeodactylum tricornutum, a unicellular eukaryotic alga. This was achieved by introducing three plant enzymes in the microalga: a Lotus japonicus oxidosqualene cyclase and a Medicago truncatula cytochrome P450 along with its native reductase. The introduction of the L. japonicus oxidosqualene cyclase perturbed the mRNA expression levels of the native mevalonate and sterol biosynthesis pathway. The best performing strains were selected and grown in a 550L pilot scale photobioreactor facility. To our knowledge, this is the most extensive pathway engineering undertaken in a diatom and the first time that a sapogenin has been artificially produced in a microalga, demonstrating the feasibility of the photo-bio-production of more complex high-value, metabolites in microalgae. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Nutrient and media recycling in heterotrophic microalgae cultures.

PubMed

Lowrey, Joshua; Armenta, Roberto E; Brooks, Marianne S

2016-02-01

In order for microalgae-based processes to reach commercial production for biofuels and high-value products such as omega-3 fatty acids, it is necessary that economic feasibility be demonstrated at the industrial scale. Therefore, process optimization is critical to ensure that the maximum yield can be achieved from the most efficient use of resources. This is particularly true for processes involving heterotrophic microalgae, which have not been studied as extensively as phototrophic microalgae. An area that has received significant conceptual praise, but little experimental validation, is that of nutrient recycling, where the waste materials from prior cultures and post-lipid extraction are reused for secondary fermentations. While the concept is very simple and could result in significant economic and environmental benefits, there are some underlying challenges that must be overcome before adoption of nutrient recycling is viable at commercial scale. Even more, adapting nutrient recycling for optimized heterotrophic cultures presents some added challenges that must be identified and addressed that have been largely unexplored to date. These challenges center on carbon and nitrogen recycling and the implications of using waste materials in conjunction with virgin nutrients for secondary cultures. The aim of this review is to provide a foundation for further understanding of nutrient recycling for microalgae cultivation. As such, we outline the current state of technology and practical challenges associated with nutrient recycling for heterotrophic microalgae on an industrial scale and give recommendations for future work.

Cultivation, characterization, and properties of Chlorella vulgaris microalgae with different lipid contents and effect on fast pyrolysis oil composition.

PubMed

Adamakis, Ioannis-Dimosthenis; Lazaridis, Polykarpos A; Terzopoulou, Evangelia; Torofias, Stylianos; Valari, Maria; Kalaitzi, Photeini; Rousonikolos, Vasilis; Gkoutzikostas, Dimitris; Zouboulis, Anastasios; Zalidis, Georgios; Triantafyllidis, Konstantinos S

2018-06-01

A systematic study of the effect of nitrogen levels in the cultivation medium of Chlorella vulgaris microalgae grown in photobioreactor (PBR) on biomass productivity, biochemical and elemental composition, fatty acid profile, heating value (HHV), and composition of the algae-derived fast pyrolysis (bio-oil) is presented in this work. A relatively high biomass productivity and cell concentration (1.5 g of dry biomass per liter of cultivation medium and 120 × 10 6 cells/ml, respectively) were achieved after 30 h of cultivation under N-rich medium. On the other hand, the highest lipid content (ca. 36 wt.% on dry biomass) was obtained under N-depletion cultivation conditions. The medium and low N levels favored also the increased concentration of the saturated and mono-unsaturated C16:0 and C18:1(n-9) fatty acids (FA) in the lipid/oil fraction, thus providing a raw lipid feedstock that can be more efficiently converted to high-quality biodiesel or green diesel (via hydrotreatment). In terms of overall lipid productivity, taking in consideration both the biomass concentration in the medium and the content of lipids on dry biomass, the most effective system was the N-rich one. The thermal (non-catalytic) pyrolysis of Chlorella vulgaris microalgae produced a highly complex bio-oil composition, including fatty acids, phenolics, ethers, ketones, etc., as well as aromatics, alkanes, and nitrogen compounds (pyrroles and amides), originating from the lipid, protein, and carbohydrate fractions of the microalgae. However, the catalytic fast pyrolysis using a highly acidic ZSM-5 zeolite, afforded a bio-oil enriched in mono-aromatics (BTX), reducing at the same time significantly oxygenated compounds such as phenolics, acids, ethers, and ketones. These effects were even more pronounced in the catalytic fast pyrolysis of Chlorella vulgaris residual biomass (after extraction of lipids), thus showing for the first time the potential of transforming this low value by-product towards high added value platform chemicals.

Wastewater nutrient removal in a mixed microalgae-bacteria culture: effect of light and temperature on the microalgae-bacteria competition.

PubMed

González-Camejo, J; Barat, R; Pachés, M; Murgui, M; Seco, A; Ferrer, J

2018-02-01

The aim of this study was to evaluate the effect of light intensity and temperature on nutrient removal and biomass productivity in a microalgae-bacteria culture and their effects on the microalgae-bacteria competition. Three experiments were carried out at constant temperature and various light intensities: 40, 85 and 125 µE m -2  s -1 . Other two experiments were carried out at variable temperatures: 23 ± 2°C and 28 ± 2°C at light intensity of 85 and 125 µE m -2  s -1 , respectively. The photobioreactor was fed by the effluent from an anaerobic membrane bioreactor. High nitrogen and phosphorus removal efficiencies (about 99%) were achieved under the following operating conditions: 85-125 µE m -2  s -1 and 22 ± 1°C. In the microalgae-bacteria culture studied, increasing light intensity favoured microalgae growth and limited the nitrification process. However, a non-graduated temperature increase (up to 32°C) under the light intensities studied caused the proliferation of nitrifying bacteria and the nitrite and nitrate accumulation. Hence, light intensity and temperature are key parameters in the control of the microalgae-bacteria competition. Biomass productivity significantly increased with light intensity, reaching 50.5 ± 9.6, 80.3 ± 6.5 and 94.3 ± 7.9 mgVSS L -1  d -1 for a light intensity of 40, 85 and 125 µE m -2  s -1 , respectively.

Effects of a docosahexaenoic acid-rich microalgae nutritional product on insulin sensitivity after prolonged dexamethasone treatment in healthy mature horses.

PubMed

Brennan, Kristen M; Graugnard, Daniel E; Spry, Malinda L; Brewster-Barnes, Tammy; Smith, Allison C; Schaeffer, Rachel E; Urschel, Kristine L

2015-10-01

To determine effects of a microalgae nutritional product on insulin sensitivity in horses. 8 healthy mature horses. PROCEDURES :Horses (n = 4/group) received a basal diet without (control diet) or with docosahexaenoic acid-rich microalgae meal (150 g/d) for 49 days (day 0 = first day of diet). On day 28, an isoglycemic hyperinsulinemic clamp procedure was performed. Horses then received dexamethasone (0.04 mg/kg/d) for 21 days. On day 49, the clamp procedure was repeated. After a 60-day washout, horses received the alternate diet, and procedures were repeated. Plasma fatty acid, glucose, and insulin concentrations and glucose and insulin dynamics during the clamp procedure were measured on days 28 and 49. Two estimates of insulin sensitivity (reciprocal of the square root of the insulin concentration and the modified insulin-to-glucose ratio for ponies) were calculated. Baseline glucose and insulin concentrations or measures of insulin sensitivity on day 28 did not differ between horses when fed the control diet or the basal diet plus microalgae meal. On day 49 (ie, after dexamethasone administration), the microalgae meal was associated with lower baseline insulin and glucose concentrations and an improved modified insulin-to-glucose ratio for ponies, compared with results for the control diet. Although the microalgae meal had no effect on clamp variables following dexamethasone treatment, it was associated with improved plasma glucose and insulin concentrations and insulin sensitivity estimates. A role for microalgae in the nutritional management of insulin-resistant horses warrants investigation.

Nutrient removal and biomass production: advances in microalgal biotechnology for wastewater treatment.

PubMed

Abinandan, Sudharsanam; Subashchandrabose, Suresh R; Venkateswarlu, Kadiyala; Megharaj, Mallavarapu

2018-05-17

Owing to certain drawbacks, such as energy-intensive operations in conventional modes of wastewater treatment (WWT), there has been an extensive search for alternative strategies in treatment technology. Biological modes for treating wastewaters are one of the finest technologies in terms of economy and efficiency. An integrated biological approach with chemical flocculation is being conventionally practiced in several-sewage and effluent treatment plants around the world. Overwhelming responsiveness to treat wastewaters especially by using microalgae is due to their simplest photosynthetic mechanism and ease of acclimation to various habitats. Microalgal technology, also known as phycoremediation, has been in use for WWT since 1950s. Various strategies for the cultivation of microalgae in WWT systems are evolving faster. However, the availability of innovative approaches for maximizing the treatment efficiency, coupled with biomass productivity, remains the major bottleneck for commercialization of microalgal technology. Investment costs and invasive parameters also delimit the use of microalgae in WWT. This review critically discusses the merits and demerits of microalgal cultivation strategies recently developed for maximum pollutant removal as well as biomass productivity. Also, the potential of algal biofilm technology in pollutant removal, and harvesting the microalgal biomass using different techniques have been highlighted. Finally, an economic assessment of the currently available methods has been made to validate microalgal cultivation in wastewater at the commercial level.

Hydrodynamic study of an internal airlift reactor for microalgae culture.

PubMed

Rengel, Ana; Zoughaib, Assaad; Dron, Dominique; Clodic, Denis

2012-01-01

Internal airlift reactors are closed systems considered today for microalgae cultivation. Several works have studied their hydrodynamics but based on important solid concentrations, not with biomass concentrations usually found in microalgae cultures. In this study, an internal airlift reactor has been built and tested in order to clarify the hydrodynamics of this system, based on microalgae typical concentrations. A model is proposed taking into account the variation of air bubble velocity according to volumetric air flow rate injected into the system. A relationship between riser and downcomer gas holdups is established, which varied slightly with solids concentrations. The repartition of solids along the reactor resulted to be homogenous for the range of concentrations and volumetric air flow rate studied here. Liquid velocities increase with volumetric air flow rate, and they vary slightly when solids are added to the system. Finally, liquid circulation time found in each section of the reactor is in concordance with those employed in microalgae culture.

Magnetophoretic harvesting of oleaginous Chlorella sp. by using biocompatible chitosan/magnetic nanoparticle composites.

PubMed

Lee, Kyubock; Lee, So Yeun; Na, Jeong-Geol; Jeon, Sang Goo; Praveenkumar, Ramasamy; Kim, Dong-Myung; Chang, Won-Seok; Oh, You-Kwan

2013-12-01

The consumption of energy and resources such as water in the cultivation and harvesting steps should be minimized to reduce the overall cost of biodiesel production from microalgae. Here we present a biocompatible and rapid magnetophoretic harvesting process of oleaginous microalgae by using chitosan-Fe3O4 nanoparticle composites. Over 99% of microalgae was harvested by using the composites and the external magnetic field without changing the pH of culture medium so that it may be reused for microalgal culture without adverse effect on the cell growth. Depending on the working volume (20-500 mL) and the strength of surface magnetic-field (3400-9200 G), the process of harvesting microalgae took only 2-5 min. The method presented here not only utilizes permanent magnets without additional energy for fast harvesting but also recycles the medium effectively for further cultivation of microalgae, looking ahead to a large scale economic microalgae-based biorefinement. Copyright © 2013 Elsevier Ltd. All rights reserved.

Enhancement of growth and lipid production from microalgae using fluorescent paint under the solar radiation.

PubMed

Seo, Yeong Hwan; Cho, Changsoon; Lee, Jung-Yong; Han, Jong-In

2014-12-01

Solar radiation has intensity that is too high to inhibit microalgae activity and is composed of wide light spectrum including ultraviolet (UV) range which cannot be utilized for microalgae. For these reasons, the modification of solar radiation is required for effective microalgae cultivation, and to do that, fluorescent paint was used for not only blocking excessive solar energy but also converting UV to visible light. With fluorescent aqueous layer, microalgae was protected from photoinhibition and could grow well, but there was difference in growth and lipid accumulation efficiencies depending on the color; maximum dry weight of 1.7 g/L was achieved in red paint, whereas best lipid content of 30% was obtained in blue one. This phenomenon was due to the different light spectrum made by colors. With simple process using fluorescent paint, modification of light was successfully done and allowing microalgae to grow under strong radiation such as solar radiation. Copyright © 2014 Elsevier Ltd. All rights reserved.

A cost analysis of microalgal biomass and biodiesel production in open raceways treating municipal wastewater and under optimum light wavelength.

PubMed

Kang, Zion; Kim, Byung-Hyuk; Ramanan, Rishiram; Choi, Jong-Eun; Yang, Ji-Won; Oh, Hee-Mock; Kim, Hee-Sik

2015-01-01

Open raceway ponds are cost-efficient for mass cultivation of microalgae compared with photobioreactors. Although low-cost options like wastewater as nutrient source is studied to overcome the commercialization threshold for biodiesel production from microalgae, a cost analysis on the use of wastewater and other incremental increases in productivity has not been elucidated. We determined the effect of using wastewater and wavelength filters on microalgal productivity. Experimental results were then fitted into a model, and cost analysis was performed in comparison with control raceways. Three different microalgal strains, Chlorella vulgaris AG10032, Chlorella sp. JK2, and Scenedesmus sp. JK10, were tested for nutrient removal under different light wavelengths (blue, green, red, and white) using filters in batch cultivation. Blue wavelength showed an average of 27% higher nutrient removal and at least 42% higher chemical oxygen demand removal compared with white light. Naturally, the specific growth rate of microalgae cultivated under blue wavelength was on average 10.8% higher than white wavelength. Similarly, lipid productivity was highest in blue wavelength, at least 46.8% higher than white wavelength, whereas FAME composition revealed a mild increase in oleic and palmitic acid levels. Cost analysis reveals that raceways treating wastewater and using monochromatic wavelength would decrease costs from 2.71 to 0.73 $/kg biomass. We prove that increasing both biomass and lipid productivity is possible through cost-effective approaches, thereby accelerating the commercialization of low-value products from microalgae, like biodiesel.

Impact of temperature on fatty acid composition and nutritional value in eight species of microalgae.

PubMed

Aussant, Justine; Guihéneuf, Freddy; Stengel, Dagmar B

2018-06-01

Microalgae are considered a sustainable source of high-value products with health benefits. Marine algae-derived omega-3 long-chain polyunsaturated fatty acids (LC-PUFA), such as eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), are considered dietary elements with effects on mental health, cognition enhancement, and cardiovascular protection. This study investigated the temperature effect on omega-3 LC-PUFA production in eight species of microalgae from various taxonomic groups, with a focus on achieving an optimal balance between omega-3 accumulation and efficient growth performance. Samples were batch-cultivated at four different temperatures, with constant light, and fatty acid methyl esters (FAME) were analyzed by gas chromatography. Several nutritional indices were calculated to assess the potential value of biomass produced for human consumption. Two promising candidates were identified suitable for batch cultivation and large-scale production: Nannochloropsis oculata for EPA and Isochrysis galbana for DHA production, with optimum productivities obtained between 14 and 20 °C, and nutritional indices falling within the range required for nutritional benefit.

Biotechnological potential of Synechocystis salina co-cultures with selected microalgae and cyanobacteria: Nutrients removal, biomass and lipid production.

PubMed

Gonçalves, Ana L; Pires, José C M; Simões, Manuel

2016-01-01

Cultivation of microalgae and cyanobacteria has been the focus of several research studies worldwide, due to the huge biotechnological potential of these photosynthetic microorganisms. However, production of these microorganisms is still not economically viable. One possible alternative to improve the economic feasibility of the process is the use of consortia between microalgae and/or cyanobacteria. In this study, Chlorella vulgaris, Pseudokirchneriella subcapitata and Microcystis aeruginosa were co-cultivated with Synechocystis salina to evaluate how dual-species cultures can influence biomass and lipid production and nutrients removal. Results have shown that the three studied consortia achieved higher biomass productivities than the individual cultures. Additionally, nitrogen and phosphorus consumption rates by the consortia provided final concentrations below the values established by European Union legislation for these nutrients. In the case of lipid productivities, higher values were determined when S. salina was co-cultivated with P. subcapitata and M. aeruginosa. Copyright © 2015 Elsevier Ltd. All rights reserved.

Photosymbiotic giant clams are transformers of solar flux.

PubMed

Holt, Amanda L; Vahidinia, Sanaz; Gagnon, Yakir Luc; Morse, Daniel E; Sweeney, Alison M

2014-12-06

'Giant' tridacnid clams have evolved a three-dimensional, spatially efficient, photodamage-preventing system for photosymbiosis. We discovered that the mantle tissue of giant clams, which harbours symbiotic nutrition-providing microalgae, contains a layer of iridescent cells called iridocytes that serve to distribute photosynthetically productive wavelengths by lateral and forward-scattering of light into the tissue while back-reflecting non-productive wavelengths with a Bragg mirror. The wavelength- and angle-dependent scattering from the iridocytes is geometrically coupled to the vertically pillared microalgae, resulting in an even re-distribution of the incoming light along the sides of the pillars, thus enabling photosynthesis deep in the tissue. There is a physical analogy between the evolved function of the clam system and an electric transformer, which changes energy flux per area in a system while conserving total energy. At incident light levels found on shallow coral reefs, this arrangement may allow algae within the clam system to both efficiently use all incident solar energy and avoid the photodamage and efficiency losses due to non-photochemical quenching that occur in the reef-building coral photosymbiosis. Both intra-tissue radiometry and multiscale optical modelling support our interpretation of the system's photophysics. This highly evolved 'three-dimensional' biophotonic system suggests a strategy for more efficient, damage-resistant photovoltaic materials and more spatially efficient solar production of algal biofuels, foods and chemicals.

Influence of oxygen on the biosynthesis of polyunsaturated fatty acids in microalgae.

PubMed

Sun, Xiao-Man; Geng, Ling-Jun; Ren, Lu-Jing; Ji, Xiao-Jun; Hao, Ning; Chen, Ke-Quan; Huang, He

2018-02-01

As one of the most important environmental factors, oxygen is particularly important for synthesis of n-3 polyunsaturated fatty acids (n-3 PUFA) in microalgae. In general, a higher oxygen supply is beneficial for cell growth but obstructs PUFA synthesis. The generation of reactive oxygen species (ROS) under aerobic conditions, which leads to the peroxidation of lipids and especially PUFA, is an inevitable aspect of life, but is often ignored in fermentation processes. Irritability, microalgal cells are able to activate a number of anti-oxidative defenses, and the lipid profile of many species is reported to be altered under oxidative stress. In this review, the effects of oxygen on the PUFA synthesis, sources of oxidative damage, and anti-oxidative defense systems of microalgae were summarized and discussed. Moreover, this review summarizes the published reports on microalgal biotechnology involving direct/indirect oxygen regulation and new bioreactor designs that enable the improved production of PUFA. Copyright © 2017 Elsevier Ltd. All rights reserved.

Extraction and purification of high-value metabolites from microalgae: essential lipids, astaxanthin and phycobiliproteins

PubMed Central

Cuellar-Bermudez, Sara P; Aguilar-Hernandez, Iris; Cardenas-Chavez, Diana L; Ornelas-Soto, Nancy; Romero-Ogawa, Miguel A; Parra-Saldivar, Roberto

2015-01-01

The marked trend and consumers growing interest in natural and healthy products have forced researches and industry to develop novel products with functional ingredients. Microalgae have been recognized as source of functional ingredients with positive health effects since these microorganisms produce polyunsaturated fatty acids, polysaccharides, natural pigments, essential minerals, vitamins, enzymes and bioactive peptides. For this reason, the manuscript reviews two of the main high-value metabolites which can be obtained from microalgae: pigments and essential lipids. Therefore, the extraction and purification methods for polyunsaturated fatty acids, astaxanthin, phycoerythrin and phycocyanin are described. Also, the effect that environmental growth conditions have in the production of these metabolites is described. This review summarizes the existing methods to extract and purify such metabolites in order to develop a feasible and sustainable algae industry. PMID:25223877

Astaxanthin-Producing Green Microalga Haematococcus pluvialis: From Single Cell to High Value Commercial Products

PubMed Central

Shah, Md. Mahfuzur R.; Liang, Yuanmei; Cheng, Jay J.; Daroch, Maurycy

2016-01-01

Many species of microalgae have been used as source of nutrient rich food, feed, and health promoting compounds. Among the commercially important microalgae, Haematococcus pluvialis is the richest source of natural astaxanthin which is considered as “super anti-oxidant.” Natural astaxanthin produced by H. pluvialis has significantly greater antioxidant capacity than the synthetic one. Astaxanthin has important applications in the nutraceuticals, cosmetics, food, and aquaculture industries. It is now evident that, astaxanthin can significantly reduce free radicals and oxidative stress and help human body maintain a healthy state. With extraordinary potency and increase in demand, astaxanthin is one of the high-value microalgal products of the future.This comprehensive review summarizes the most important aspects of the biology, biochemical composition, biosynthesis, and astaxanthin accumulation in the cells of H. pluvialis and its wide range of applications for humans and animals. In this paper, important and recent developments ranging from cultivation, harvest and postharvest bio-processing technologies to metabolic control and genetic engineering are reviewed in detail, focusing on biomass and astaxanthin production from this biotechnologically important microalga. Simultaneously, critical bottlenecks and major challenges in commercial scale production; current and prospective global market of H. pluvialis derived astaxanthin are also presented in a critical manner. A new biorefinery concept for H. pluvialis has been also suggested to guide toward economically sustainable approach for microalgae cultivation and processing. This report could serve as a useful guide to present current status of knowledge in the field and highlight key areas for future development of H. pluvialis astaxanthin technology and its large scale commercial implementation. PMID:27200009

Toxicity of silver and gold nanoparticles on marine microalgae.

PubMed

Moreno-Garrido, Ignacio; Pérez, Sara; Blasco, Julián

2015-10-01

The increased use of nanomaterials in several novel industrial applications during the last decade has led to a rise in concerns about the potential toxic effects of released engineered nanoparticles (NPs) into the environment, as their potential toxicity to aquatic organisms is just beginning to be recognised. Toxicity of metallic nanoparticles to aquatic organisms, including microalgae, seems to be related to their physical and chemical properties, as well as their behaviour in the aquatic media where processes of dissolution, aggregation and agglomeration can occur. Although the production of these particles has increased considerably in recent years, data on their toxicity on microalgae, especially those belonging to marine or estuarine environments remain scarce and scattered. The literature shows a wide variation of results on toxicity, mainly due to the different methodology used in bioassays involving microalgae. These can range for up to EC50 data, in the case of AgNPs, representing five orders of magnitude. The importance of initial cellular density is also addressed in the text, as well as the need for keeping test conditions as close as possible to environmental conditions, in order to increase their environmental relevance. This review focuses on the fate and toxicity of silver, gold, and gold-silver alloy nanoparticles on microalgae, as key organisms in aquatic ecosystems. It is prompted by their increased production and use, and taking into account that oceans and estuaries are the final sink for those NPs. The design of bioassays and further research in the field of microalgae nanoecotoxicology is discussed, with a brief survey on newly developed technology of green (algae mediated) production of Ag, Au and Ag-Au bimetallic NPs, as well as some final considerations about future research on this field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Microalgae population dynamics in photobioreactors with secondary sewage effluent as culture medium

PubMed Central

Marchello, Adriano E.; Lombardi, Ana T.; Dellamano-Oliveira, Maria José; de Souza, Clovis W.O.

2015-01-01

Nitrogen and phosphorus present in sewage can be used for microalgae growth, possibiliting cost reduction in the production of microalgae at the same time that it decreases the eutrophication potential of the effluent. This research aimed at monitoring the native community of microalgae and coliform bacteria in a secondary effluent from anaerobic municipal sewage treatment. Two treatments (aerated and non-aerated) were performed to grow microalgae under semi-controlled conditions in semi-closed photobioreactors in a greenhouse. The results showed no significant pH and coliforms (total and Escherichia coli ) variation between treatments. Nutrient concentrations were reduced supporting microalgae growth up to 10 7 cells.mL −1 independent of aeration. Exponential growth was obtained from the first day for the non-aerated, but a 5 day lag phase of growth was obtained for the aerated. Chlorella vulgaris was the dominant microalgae (99.9%) in both treatments. In the aerated, 5 algae classes were detected (Chlorophyceae, Cyanophyceae, Chrysophyceae, Bacillariophyceae and Euglenophyceae), with 12 taxa, whereas in the non-aerated, 2 classes were identified (Chlorophyceae and Cyanophyceae), with 5 taxa. We concluded that effluent is viable for microalgae growth, especially Chlorella vulgaris, at the same time that the eutrophication potential and coliforms are decreased, contributing for better quality of the final effluent. PMID:26221091

Purification of microalgae from bacterial contamination using a disposable inertia-based microfluidic device

NASA Astrophysics Data System (ADS)

Godino, Neus; Jorde, Felix; Lawlor, Daryl; Jaeger, Magnus; Duschl, Claus

2015-08-01

Microalgae are a promising source of bioactive ingredients for the food, pharmaceutical and cosmetic industries. Every microalgae research group or production facility is facing one major problem regarding the potential contamination of the algal cell with bacteria. Prior to the storage of the microalgae in strain collections or to cultivation in bioreactors, it is necessary to carry out laborious purification procedures to separate the microalgae from the undesired bacterial cells. In this work, we present a disposable microfluidic cartridge for the high-throughput purification of microalgae samples based on inertial microfluidics. Some of the most relevant microalgae strains have a larger size than the relatively small, few micron bacterial cells, so making them distinguishable by size. The inertial microfluidic cartridge was fabricated with inexpensive materials, like pressure sensitive adhesive (PSA) and thin plastic layers, which were patterned using a simple cutting plotter. In spite of fabrication restrictions and the intrinsic difficulties of biological samples, the separation of microalgae from bacteria reached values in excess of 99%, previously only achieved using conventional high-end and high cost lithography methods. Moreover, due to the simple and high-throughput characteristic of the separation, it is possible to concatenate serial purification to exponentially decrease the absolute amount of bacteria in the final purified sample.

Photosynthetic aeration in biological wastewater treatment using immobilized microalgae-bacteria symbiosis.

PubMed

Praveen, Prashant; Loh, Kai-Chee

2015-12-01

Chlorella vulgaris encapsulated in alginate beads were added into a bioreactor treating synthetic wastewater using Pseudomonas putida. A symbiotic CO2/O2 gas exchange was established between the two microorganisms for photosynthetic aeration of wastewater. During batch operation, glucose removal efficiency in the bioreactor improved from 50% in 12 h without aeration to 100% in 6 h, when the bioreactor was aerated photosynthetically. During continuous operation, the bioreactor was operated at a low hydraulic retention time of 3.3 h at feed concentrations of 250 and 500 mg/L glucose. The removal efficiency at 500 mg/L increased from 73% without aeration to 100% in the presence of immobilized microalgae. The initial microalgae concentration was critical to achieve adequate aeration, and the removal rate increased with increasing microalgae concentration. The highest removal rate of 142 mg/L-h glucose was achieved at an initial microalgae concentration of 190 mg/L. Quantification of microalgae growth in the alginate beads indicated an exponential growth during symbiosis, indicating that the bioreactor performance was limited by oxygen production rates. Under symbiotic conditions, the chlorophyll content of the immobilized microalgae increased by more than 30%. These results indicate that immobilized microalgae in symbiosis with heterotrophic bacteria are promising in wastewater aeration.

Chemical composition and physicochemical properties of Phaeodactylum tricornutum microalgal residual biomass.

PubMed

German-Báez, L J; Valdez-Flores, M A; Félix-Medina, J V; Norzagaray-Valenzuela, C D; Santos-Ballardo, D U; Reyes-Moreno, C; Shelton, L M; Valdez-Ortiz, A

2017-12-01

The production of photosynthetic biofuels using microalgae is a promising strategy to combat the use of non-renewable energy sources. The microalgae residual biomass is a waste by-product of biofuel production; however, it could prove to have utility in the development of sustainable nutraceuticals and functional foods. In this study, a comprehensive characterisation of the under-utilised Phaeodactylum tricornutum microalgae residual biomass is presented. Proximal composition, antioxidant capacity (using three different antioxidant assays; oxygen radical absorbance capacity; radical cation activity, ABTS; and radical scavenging activity, DPPH), and total phenolic content of free and bound polyphenols were determined. Additionally, the physicochemical properties of water activity, pH, water absorption index, water solubility index, and dispersibility were evaluated. Results revealed that P. tricornutum microalgae residual biomass exhibits a relatively high protein and carbohydrate content, with values of 36.67% and 46.78%, respectively; and most carbohydrates were found as total dietary fibre (45.57%), of which insoluble dietary fibre was the most predominant (43.54%). Antioxidant capacity values for total phytochemicals of 106.22, 67.93, 9.54 µM TE g -1 dw were determined by oxygen radical absorbance capacity, ABTS, and DPPH assays, respectively. Total phenolic content was found to be 2.90 mg GAE g -1 dw. Interestingly, antioxidant capacity and total phenolic content were higher in bound than in free phytochemical extracts. The physicochemical analysis showed P. tricornutum microalgae residual biomass to have suitable properties for the generation of a beverage with Aw, pH, water absorption index, water solubility index, and dispersibility values of 0.45, 7.12, 3.40 g gel g -1  dw, 2.5 g solids 100 g -1  dw, and 90%, respectively. Hence, P. tricornutum microalgae residual biomass could be considered a potential source of bioactive compounds suitable for the production of functional food exhibiting antioxidant capacity and high dietary fibre content.

Nitrogen and Phosphorus Biomass-Kinetic Model for Chlorella vulgaris in a Biofuel Production Scheme

DTIC Science & Technology

2010-03-01

removal from urban wastewater by the microalga Scenedesmus obliquus. Bioresource Technology , 73: 263-272. Mata, T., Martins, A., & Caetano, N... nutrient removal in free and immobilized green algae in batch and semi-continuous cultures treating real wastewater . Bioresource Technology , 101: 58-64...Bashan, Y. (2002). Treatment of recalcitrant wastewater from ethanol and citric acid production using the microalga Chlorella vulgaris and the

Slab waveguide photobioreactors for microalgae based biofuel production.

PubMed

Jung, Erica Eunjung; Kalontarov, Michael; Doud, Devin F R; Ooms, Matthew D; Angenent, Largus T; Sinton, David; Erickson, David

2012-10-07

Microalgae are a promising feedstock for sustainable biofuel production. At present, however, there are a number of challenges that limit the economic viability of the process. Two of the major challenges are the non-uniform distribution of light in photobioreactors and the inefficiencies associated with traditional biomass processing. To address the latter limitation, a number of studies have demonstrated organisms that directly secrete fuels without requiring organism harvesting. In this paper, we demonstrate a novel optofluidic photobioreactor that can help address the light distribution challenge while being compatible with these chemical secreting organisms. Our approach is based on light delivery to surface bound photosynthetic organisms through the evanescent field of an optically excited slab waveguide. In addition to characterizing organism growth-rates in the system, we also show here, for the first time, that the photon usage efficiency of evanescent field illumination is comparable to the direct illumination used in traditional photobioreactors. We also show that the stackable nature of the slab waveguide approach could yield a 12-fold improvement in the volumetric productivity.

Influence of tryptophan and indole-3-acetic acid on starch accumulation in the synthetic mutualistic Chlorella sorokiniana-Azospirillum brasilense system under heterotrophic conditions.

PubMed

Palacios, Oskar A; Choix, Francisco J; Bashan, Yoav; de-Bashan, Luz E

2016-06-01

This study measured the relations between tryptophan production, the phytohormone indole-3-acetic acid (IAA) and the metabolism and accumulation of starch during synthetic mutualism between the microalgae Chlorella sorokiniana and the microalgae growth-promoting bacteria Azospirillum brasilense, created by co-immobilization in alginate beads. Experiments used two wild-type A. brasilense strains (Cd and Sp6) and an IAA-attenuated mutant (SpM7918) grown under nitrogen-replete and nitrogen-starved conditions tested under dark, heterotrophic and aerobic growth conditions. Under all incubating conditions, C. sorokiniana, but not A. brasilense, produced tryptophan. A significant correlation between IAA-production by A. brasilense and starch accumulation in C. sorokiniana was found, since the IAA-attenuated mutant was not producing increased starch levels. The highest ADP-glucose pyrophosphorylase (AGPase) activity, starch content and glucose uptake were found during the interaction of A. brasilense wild type strains with the microalgae. When the microalgae were grown alone, they produced only small amounts of starch. Supplementation with synthetic IAA to C. sorokiniana grown alone enhanced the above parameters, but only transiently. Activity of α-amylase decreased under nitrogen-replete conditions, but increased under nitrogen-starved conditions. In summary, this study demonstrated that, during synthetic mutualism, the exchange of tryptophan and IAA between the partners is a mechanism that governs several changes in starch metabolism of C. sorokiniana, yielding an increase in starch content. Copyright © 2016 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Biodiesel production from Spirulina microalgae feedstock using direct transesterification near supercritical methanol condition.

PubMed

Mohamadzadeh Shirazi, Hamed; Karimi-Sabet, Javad; Ghotbi, Cyrus

2017-09-01

Microalgae as a candidate for production of biodiesel, possesses a hard cell wall that prevents intracellular lipids leaving out from the cells. Direct or in situ supercritical transesterification has the potential for destruction of microalgae hard cell wall and conversion of extracted lipids to biodiesel that consequently reduces the total energy consumption. Response surface methodology combined with central composite design was applied to investigate process parameters including: Temperature, Time, Methanol-to-dry algae, Hexane-to-dry algae, and Moisture content. Thirty-two experiments were designed and performed in a batch reactor, and biodiesel efficiency between 0.44% and 99.32% was obtained. According to fatty acid methyl ester yields, a quadratic experimental model was adjusted and the significance of parameters was evaluated using analysis of variance (ANOVA). Effects of single and interaction parameters were also interpreted. In addition, the effect of supercritical process on the ultrastructure of microalgae cell wall using scanning electron spectrometry (SEM) was surveyed. Copyright © 2017 Elsevier Ltd. All rights reserved.

A whole biodiesel conversion process combining isolation, cultivation and in situ supercritical methanol transesterification of native microalgae.

PubMed

Jazzar, Souhir; Quesada-Medina, Joaquín; Olivares-Carrillo, Pilar; Marzouki, Mohamed Néjib; Acién-Fernández, Francisco Gabriel; Fernández-Sevilla, José María; Molina-Grima, Emilio; Smaali, Issam

2015-08-01

A coupled process combining microalgae production with direct supercritical biodiesel conversion using a reduced number of operating steps is proposed in this work. Two newly isolated native microalgae strains, identified as Chlorella sp. and Nannochloris sp., were cultivated in both batch and continuous modes. Maximum productivities were achieved during continuous cultures with 318mg/lday and 256mg/lday for Chlorella sp. and Nannochloris sp., respectively. Microalgae were further characterized by determining their photosynthetic performance and nutrient removal efficiency. Biodiesel was produced by catalyst-free in situ supercritical methanol transesterification of wet unwashed algal biomass (75wt.% of moisture). Maximum biodiesel yields of 45.62wt.% and 21.79wt.% were reached for Chlorella sp. and Nannochloris sp., respectively. The analysis of polyunsaturated fatty acids of Chlorella sp. showed a decrease in their proportion when comparing conventional and supercritical transesterification processes (from 37.4% to 13.9%, respectively), thus improving the quality of the biodiesel. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessing microalgae biorefinery routes for the production of biofuels via hydrothermal liquefaction.

PubMed

López Barreiro, Diego; Samorì, Chiara; Terranella, Giuseppe; Hornung, Ursel; Kruse, Andrea; Prins, Wolter

2014-12-01

The interest in third generation biofuels from microalgae has been rising during the past years. Meanwhile, it seems not economically feasible to grow algae just for biofuels. Co-products with a higher value should be produced by extracting a particular algae fraction to improve the economics of an algae biorefinery. The present study aims at analyzing the influence of two main microalgae components (lipids and proteins) on the composition and quantity of biocrude oil obtained via hydrothermal liquefaction of two strains (Nannochloropsis gaditana and Scenedesmus almeriensis). The algae were liquefied as raw biomass, after extracting lipids and after extracting proteins in microautoclave experiments at different temperatures (300-375°C) for 5 and 15min. The results indicate that extracting the proteins from the microalgae prior to HTL may be interesting to improve the economics of the process while at the same time reducing the nitrogen content of the biocrude oil. Copyright © 2014 Elsevier Ltd. All rights reserved.

Efficacy of Chlorella pyrenoidosa and Scenedesmus abundans for Nutrient Removal in Rice Mill Effluent (Paddy Soaked Water).

PubMed

Abinandan, S; Bhattacharya, Ribhu; Shanthakumar, S

2015-01-01

Microalgae are product of sustainable development owing to its ability to treat variety of wastewater effluents and thus produced biomass can serve as value added product for various commercial applications. This paper deals with the cultivation of microalgae species namely Chlorella pyrenoidosa and Scenedesmus abundans in rice mill effluent (i.e., paddy soaked water) for nutrient removal. In order to investigate the nutrient removal capability, microalgae are subjected to cultivation in both raw and autoclaved samples. The maximum phosphate removal by Scenedesmus abundans and Chlorella pyrenoidosa in raw sample was 98.3% and 97.6%, respectively, whereas, the removal of ammoniacal nitrogen by Scenedesmus abundans and Chlorella pyrenoidosa in raw sample was 92% and 90.3%, respectively. The growth (measured in terms of chlorophyll content) of Scenedesmus abundans and Chlorella pyrenoidosa in raw sample was 3.88 mg/l and 5.55 mg/l, respectively. The results indicate the suitability of microalgae cultivation in rice mill effluent treatment for nutrient removal.

Biogas production coupled to repeat microalgae cultivation using a closed nutrient loop.

PubMed

González-González, Lina María; Zhou, Lihong; Astals, Sergi; Thomas-Hall, Skye R; Eltanahy, Eladl; Pratt, Steven; Jensen, Paul D; Schenk, Peer M

2018-05-22

Anaerobic digestion is an established technology to produce renewable energy as methane-rich biogas for which microalgae are a suitable substrate. Besides biogas production, anaerobic digestion of microalgae generates an effluent rich in nutrients, so-called digestate, that can be used as a growth medium for microalgal cultures, with the potential for a closed nutrient loop and sustainable bioenergy facility. In this study, the methane potential and nutrient mobilization of the microalga Scenedemus dimorphus was evaluated under continuous conditions. The suitability of using the digestate as culture medium was also evaluated. The results show that S. dimorphus is a suitable substrate for anaerobic digestion with an average methane yield of 199 mL g -1 VS. The low level of phosphorus in digestate did not limit algae growth when used as culture medium. The potential of liquid digestate as a superior culture medium rather than inorganic medium was demonstrated. Copyright © 2018. Published by Elsevier Ltd.

Biological system development for GraviSat: A new platform for studying photosynthesis and microalgae in space

NASA Astrophysics Data System (ADS)

Fleming, Erich D.; Bebout, Brad M.; Tan, Ming X.; Selch, Florian; Ricco, Antonio J.

2014-10-01

Microalgae have great potential to be used as part of a regenerative life support system and to facilitate in-situ resource utilization (ISRU) on long-duration human space missions. Little is currently known, however, about microalgal responses to the space environment over long (months) or even short (hours to days) time scales. We describe here the development of biological support subsystems for a prototype "3U" (i.e., three conjoined 10-cm cubes) nanosatellite, called GraviSat, designed to experimentally elucidate the effects of space microgravity and the radiation environment on microalgae and other microorganisms. The GraviSat project comprises the co-development of biological handling-and-support technologies with implementation of integrated measurement hardware for photosynthetic efficiency and physiological activity in support of long-duration (3-12 months) space missions. It supports sample replication in a fully autonomous system that will grow and analyze microalgal cultures in 120 μL wells around the circumference of a microfluidic polymer disc; the cultures will be launched while in stasis, then grown in orbit. The disc spins at different rotational velocities to generate a range of artificial gravity levels in space, from microgravity to multiples of Earth gravity. Development of the biological support technologies for GraviSat comprised the screening of more than twenty microalgal strains for various physical, metabolic and biochemical attributes that support prolonged growth in a microfluidic disc, as well as the capacity for reversible metabolic stasis. Hardware development included that necessary to facilitate accurate and precise measurements of physical parameters by optical methods (pulse amplitude modulated fluorometry) and electrochemical sensors (ion-sensitive microelectrodes). Nearly all microalgal strains were biocompatible with nanosatellite materials; however, microalgal growth was rapidly inhibited (∼1 week) within sealed microwells that did not include dissolved bicarbonate due to CO2 starvation. Additionally, oxygen production by some microalgae resulted in bubble formation within the wells, which interfered with sensor measurements. Our research achieved prolonged growth periods (>10 months) without excess oxygen production using two microalgal strains, Chlorella vulgaris UTEX 29 and Dunaliella bardawil 30 861, by lowering light intensities (2-10 μmol photons m-2 s-1) and temperature (4-12 °C). Although the experiments described here were performed to develop the GraviSat platform, the results of this study should be useful for the incorporation of microalgae in other satellite payloads with low-volume microfluidic systems.

Feasibility of carbon dioxide sequestration by Spongiochloris sp microalgae during petroleum wastewater treatment in airlift bioreactor.

PubMed

Abid, Abdeldjalil; Saidane, Faten; Hamdi, Moktar

2017-06-01

The aim of this work was to study the ability of using Hydrocabonoclastic native microbial and Spongiochloris sp microalgae in airlift bioreactors couples in order to restore hydrocarbons wastewater and develop the capacity of natural systems to reduce greenhouse effect through maximal control of CO 2 gas emission in atmosphere. The kinetic parameters of CO 2 gas fixation level and conversion it into biological material by microalgae as the biodegradation process effect in hydrocarbon have been evaluated. The result present that maximum specific growth rate μ max of Spongiochloris sp was (0.87±0.04day -1 ) and the biomass productivity P max was attended (1.5±0.3gL -1 day -1 ) with maximal CO 2 biofixation rate RCO 2 (2.9205gL -1 day -1 ). At 30°C and pH (7.6-7.4) the bioreactor showed a good wastewater removal efficiency (99.18%) in total hydrocarbons with COD stabilized within (1.30g/L), this result obtained suggesting that, the bioreactor applied system represented a useful strategy for maximizing CO 2 bio-mitigation. Copyright © 2017. Published by Elsevier Ltd.

Contribution of phytoplankton and benthic microalgae to inner shelf sediments of the north-central Gulf of Mexico

NASA Astrophysics Data System (ADS)

Grippo, M. A.; Fleeger, J. W.; Rabalais, N. N.; Condrey, R.; Carman, K. R.

2010-03-01

Marine sediment may contain both settled phytoplankton and benthic microalgae (BMA). In river-dominated, shallow continental shelf systems, spatial, and temporal heterogeneity in sediment type and water-column characteristics (e.g., turbidity and primary productivity) may promote spatial variation in the relative contribution of these two sources to the sediment organic matter pool available to benthic consumers. Here we use photosynthetic pigment analysis and microscopic examination of sediment microalgae to investigate how the biomass, composition, and degradation state of sediment-associated microalgae vary along the Louisiana (USA) inner shelf, a region strongly influenced by the Mississippi River. Three sandy shoals and surrounding muddy sediments with depths ranging from 4 to 20 m were sampled in April, August, and October 2007. Pigment composition suggested that sediment microalgae were primarily diatoms at all locations. We found no significant differences in sediment chlorophyll a concentrations (8-77 mg m -2) at the shoal and off-shoal stations. Epipelic pennate diatoms (considered indicative of BMA) made up a significantly greater proportion of sediment diatoms at sandy (50-98%) compared to more silty off-shoal stations (16-56%). The percentage of centric diatoms (indicators of settled phytoplankton) in the sediment was highest in August. Sediment total pheopigment concentrations on sandy stations (<20 mg m -2) were significantly lower than concentrations at nearby muddy stations (>40 mg m -2), suggesting differences in sediment microalgal degradation state. These observations suggest that BMA predominate in shallow sandy sediments and that phytodetritus predominates at muddy stations. Our results also suggest that the relative proportion of phytodetritus in the benthos was highest where phytoplankton biomass in the overlying water was greatest, independent of sediment type. The high biomass of BMA found on shoals suggests that benthic primary production on sandy sediments represents a potentially significant local source of sediment microalgal carbon that may be utilized by benthic consumers in continental shelf food webs.

An automated on-line turbulent flow liquid-chromatography technology coupled to a high resolution mass spectrometer LTQ-Orbitrap for suspect screening of antibiotic transformation products during microalgae wastewater treatment.

PubMed

Jaén-Gil, Adrián; Hom-Diaz, Andrea; Llorca, Marta; Vicent, Teresa; Blánquez, Paqui; Barceló, Damià; Rodríguez-Mozaz, Sara

2018-06-11

The evaluation of wastewater treatment capabilities in terms of removal of water pollutants is crucial when assessing water mitigation issues. Not only the monitoring of target pollutants becomes a critical point, but also the transformation products (TPs) generated. Since these TPs are very often unknown compounds, their study in both wastewater and natural environment is currently recognized as a tedious task and challenging research field. In this study, a novel automated suspect screening methodology was developed for a comprehensive assessment of the TPs generated from nine antibiotics during microalgae water treatment. Three macrolides (azithromycin, erythromycin, clarithromycin), three fluoroquinolones (ofloxacin, ciprofloxacin, norfloxacin) and three additional antibiotics (trimethoprim, pipemidic acid, sulfapyridine) were selected as target pollutants. The analysis of samples was carried out by direct injection in an on-line turbulent flow liquid chromatography-high resolution mass spectrometry (TFC-LC-LTQ-Orbitrap-MS/MS) system, followed by automatic data processing for compound identification. The screening methodology allowed the identification of 40 tentative TPs from a list of software predicted intermediates created automatically. Once known and unknown TPs were identified, degradation pathways were suggested considering the different mechanisms involved on their formation (biotic and abiotic). Results reveal microalgae ability for macrolide biotransformation, but not for other antibiotics such as for fluoroquinolones. Finally, the intermediates detected were included into an in-house library and applied to the identification of tentative TPs in real toilet wastewater treated in a microalgae based photobioreactor (PBR). The overall approach allowed a comprehensive overview of the performance of microalgae water treatment in a fast and reliable manner: it represents a useful tool for the rapid screening of wide range of compounds, reducing time invested in data analysis and providing reliable structural identification. Copyright © 2018 Elsevier B.V. All rights reserved.

Biodiesel from microalgae beats bioethanol.

PubMed

Chisti, Yusuf

2008-03-01

Renewable biofuels are needed to displace petroleum-derived transport fuels, which contribute to global warming and are of limited availability. Biodiesel and bioethanol are the two potential renewable fuels that have attracted the most attention. As demonstrated here, biodiesel and bioethanol produced from agricultural crops using existing methods cannot sustainably replace fossil-based transport fuels, but there is an alternative. Biodiesel from microalgae seems to be the only renewable biofuel that has the potential to completely displace petroleum-derived transport fuels without adversely affecting supply of food and other crop products. Most productive oil crops, such as oil palm, do not come close to microalgae in being able to sustainably provide the necessary amounts of biodiesel. Similarly, bioethanol from sugarcane is no match for microalgal biodiesel.

A comprehensive comparable study of the physiological properties of four microalgal species under different light wavelength conditions.

PubMed

Zhong, Yu; Jin, Peng; Cheng, Jay J

2018-05-19

Microalgae treated with blue light have potential for production of human nutrition supplement and biofuel due to their higher biomass productivity and favorable fatty acid composition. Chlorella vulgaris, Chlorella pyrenoidosa, Scenedesmus quadricauda and Scenedesmus obliquus are representative green microalgae which are widely reported for algal production. In this study, we provide a systematic investigation of the biomass productivity, photosynthetic pigments, chlorophyll fluorescence and fatty acid content of the four green microalgae. The strains were grown in two primary monochromatic light wavelengths [red and blue LEDs (light emitting diode)], and in white LED conditions, respectively. Among them, blue LED light was determined as the best light for growth rate, followed by red LED and white LED. The chlorophyll generation was more sensitive to the monochromatic blue light. The polyunsaturated fatty acids (PUFAs) such as α-linolenic acid (18:3), which were perfect for human nutrition supplementation, showed high concentrations in these algae strains under blue LED. Collectively, the results indicate that the blue LED is suitable for various food, feed, and algal biofuel productions due to both biomass and fatty acid productivity.

Potential of water surface-floating microalgae for biodiesel production: Floating-biomass and lipid productivities.

PubMed

Muto, Masaki; Nojima, Daisuke; Yue, Liang; Kanehara, Hideyuki; Naruse, Hideaki; Ujiro, Asuka; Yoshino, Tomoko; Matsunaga, Tadashi; Tanaka, Tsuyoshi

2017-03-01

Microalgae have been accepted as a promising feedstock for biodiesel production owing to their capability of converting solar energy into lipids through photosynthesis. However, the high capital and operating costs, and high energy consumption, are hampering commercialization of microalgal biodiesel. In this study, the surface-floating microalga, strain AVFF007 (tentatively identified as Botryosphaerella sudetica), which naturally forms a biofilm on surfaces, was characterized for use in biodiesel production. The biofilm could be conveniently harvested from the surface of the water by adsorbing onto a polyethylene film. The lipid productivity of strain AVFF007 was 46.3 mg/L/day, allowing direct comparison to lipid productivities of other microalgal species. The moisture content of the surface-floating biomass was 86.0 ± 1.2%, which was much lower than that of the biomass harvested using centrifugation. These results reveal the potential of this surface-floating microalgal species as a biodiesel producer, employing a novel biomass harvesting and dewatering strategy. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Effect of food wastewater on biomass production by a green microalga Scenedesmus obliquus for bioenergy generation.

PubMed

Ji, Min-Kyu; Yun, Hyun-Shik; Park, Sanghyun; Lee, Hongkyun; Park, Young-Tae; Bae, Sunyoung; Ham, Jungyeob; Choi, Jaeyoung

2015-03-01

Effect of food wastewater (FW) on the biomass, lipid and carbohydrate production by a green microalga Scenedesmus obliquus cultivated in Bold's Basal Medium (BBM) was investigated. Different dilution ratios (0.5-10%) of BBM either with FW or salt solution (NaCl) or sea water (SW) were evaluated. S. obliquus showed the highest growth (0.41 g L(-1)), lipid productivity (13.3 mg L(-1) day L(-1)), carbohydrate productivity (14.7 mg L(-1) day L(-1)) and nutrient removal (38.9 mg TN L(-1) and 12.1 mg TP L(-1)) with 1% FW after 6 days of cultivation. The FW promoted algal autoflocculation due to formation of inorganic precipitates at an alkali pH. Fatty acid methyl ester analysis revealed that the palmitic and oleic acid contents were increased up to 8% with FW. Application of FW improved the growth, lipid/carbohydrate productivity and biomass recovery efficiency of S. obliquus, which can be exploited for cost effective production of microalgae biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Saponification Method for Chlorophyll Removal from Microalgae Biomass as Oil Feedstock

PubMed Central

Li, Tao; Xu, Jin; Wu, Hualian; Wang, Guanghua; Dai, Shikun; Fan, Jiewei; He, Hui; Xiang, Wenzhou

2016-01-01

Microalgae oil is an optimal feedstock for nutraceutical, pharmaceutical and biodiesel production, but its high levels of chlorophyll limit its large-scale application. To date, few effective approaches have been developed to remove chlorophyll from microalgae oil. The main purpose of this study was to present a preprocessing method of algae oil feedstock (Scenedesmus) to remove chlorophyll by saponification. The results showed that 96% of chlorophyll in biomass was removed. High quality orange transparent oil could be extracted from the chlorophyll reduced biomass. Specifically, the proportion of neutral lipids and saturation levels of fatty acids increased, and the pigments composition became carotenoids-based. The critical parameters of chlorophyll reduced biodiesel conformed to the standards of the USA, China and EU. Sodium copper chlorophyllin could be prepared from the bleaching effluent. The results presented herein offer a useful pathway to improve the quality of microalgae oil and reduce the cost of microalgae biodiesel. PMID:27618070

A Saponification Method for Chlorophyll Removal from Microalgae Biomass as Oil Feedstock.

PubMed

Li, Tao; Xu, Jin; Wu, Hualian; Wang, Guanghua; Dai, Shikun; Fan, Jiewei; He, Hui; Xiang, Wenzhou

2016-09-07

Microalgae oil is an optimal feedstock for nutraceutical, pharmaceutical and biodiesel production, but its high levels of chlorophyll limit its large-scale application. To date, few effective approaches have been developed to remove chlorophyll from microalgae oil. The main purpose of this study was to present a preprocessing method of algae oil feedstock (Scenedesmus) to remove chlorophyll by saponification. The results showed that 96% of chlorophyll in biomass was removed. High quality orange transparent oil could be extracted from the chlorophyll reduced biomass. Specifically, the proportion of neutral lipids and saturation levels of fatty acids increased, and the pigments composition became carotenoids-based. The critical parameters of chlorophyll reduced biodiesel conformed to the standards of the USA, China and EU. Sodium copper chlorophyllin could be prepared from the bleaching effluent. The results presented herein offer a useful pathway to improve the quality of microalgae oil and reduce the cost of microalgae biodiesel.

Cell disruption for microalgae biorefineries.

PubMed

Günerken, E; D'Hondt, E; Eppink, M H M; Garcia-Gonzalez, L; Elst, K; Wijffels, R H

2015-01-01

Microalgae are a potential source for various valuable chemicals for commercial applications ranging from nutraceuticals to fuels. Objective in a biorefinery is to utilize biomass ingredients efficiently similarly to petroleum refineries in which oil is fractionated in fuels and a variety of products with higher value. Downstream processes in microalgae biorefineries consist of different steps whereof cell disruption is the most crucial part. To maintain the functionality of algae biochemicals during cell disruption while obtaining high disruption yields is an important challenge. Despite this need, studies on mild disruption of microalgae cells are limited. This review article focuses on the evaluation of conventional and emerging cell disruption technologies, and a comparison thereof with respect to their potential for the future microalgae biorefineries. The discussed techniques are bead milling, high pressure homogenization, high speed homogenization, ultrasonication, microwave treatment, pulsed electric field treatment, non-mechanical cell disruption and some emerging technologies. Copyright © 2015 Elsevier Inc. All rights reserved.

Toxic pressure of herbicides on microalgae in Dutch estuarine and coastal waters

NASA Astrophysics Data System (ADS)

Booij, Petra; Sjollema, Sascha B.; van der Geest, Harm G.; Leonards, Pim E. G.; Lamoree, Marja H.; de Voogt, W. Pim; Admiraal, Wim; Laane, Remi W. P. M.; Vethaak, A. Dick

2015-08-01

For several decades now, there has been an increase in the sources and types of chemicals in estuarine and coastal waters as a consequence of anthropogenic activities. This has led to considerable concern about the effects of these chemicals on the marine food chain. The fact is that estuarine and coastal waters are the most productive ecosystems with high primary production by microalgae. The toxic pressure of specific phytotoxic chemicals now poses a major threat to these ecosystems. In a previous study, six herbicides (atrazine, diuron, irgarol, isoproturon, terbutryn and terbutylazine) were identified as the main contaminants affecting photosynthesis in marine microalgae. The purpose of this study is to investigate the toxic pressure of these herbicides in the Dutch estuarine and coastal waters in relation to the effective photosystem II efficiency (ΦPSII) in microalgae. Temporal and spatial variations in the concentrations of these herbicides were analyzed based on monitoring data. Additionally, a field study was carried out in which chemical analysis of water was performed and also a toxicity assessment using the Pulse Amplitude Modulation (PAM) fluorometry assay that measures ΦPSII. The toxic pressure on ΦPSII in microalgae has decreased with 55-82% from 2003 to 2012, with the Western Scheldt estuary showing the highest toxic pressure. By combining toxicity data from the PAM assay with chemical analysis of herbicide concentrations, we have identified diuron and terbutylazine as the main contributors to the toxic pressure on microalgae. Although direct effects are not expected, the toxic pressure is close to the 10% effect level in the PAM assay. A compliance check with the current environmental legislation of the European Union revealed that the quality standards are not sufficient to protect marine microalgae.

A mathematical model of microalgae growth in cylindrical photobioreactor

NASA Astrophysics Data System (ADS)

Bakeri, Noorhadila Mohd; Jamaian, Siti Suhana

2017-08-01

Microalgae are unicellular organisms, which exist individually or in chains or groups but can be utilized in many applications. Researchers have done various efforts in order to increase the growth rate of microalgae. Microalgae have a potential as an effective tool for wastewater treatment, besides as a replacement for natural fuel such as coal and biodiesel. The growth of microalgae can be estimated by using Geider model, which this model is based on photosynthesis irradiance curve (PI-curve) and focused on flat panel photobioreactor. Therefore, in this study a mathematical model for microalgae growth in cylindrical photobioreactor is proposed based on the Geider model. The light irradiance is the crucial part that affects the growth rate of microalgae. The absorbed photon flux will be determined by calculating the average light irradiance in a cylindrical system illuminated by unidirectional parallel flux and considering the cylinder as a collection of differential parallelepipeds. Results from this study showed that the specific growth rate of microalgae increases until the constant level is achieved. Therefore, the proposed mathematical model can be used to estimate the rate of microalgae growth in cylindrical photobioreactor.

Hydrogen and lipid production from starch wastewater by co-culture of anaerobic sludge and oleaginous microalgae with simultaneous COD, nitrogen and phosphorus removal.

PubMed

Ren, Hong-Yu; Liu, Bing-Feng; Kong, Fanying; Zhao, Lei; Ren, Nanqi

2015-11-15

Anaerobic sludge (AS) and microalgae were co-cultured to enhance the energy conversion and nutrients removal from starch wastewater. Mixed ratio, starch concentration and initial pH played critical roles on the hydrogen and lipid production of the co-culture system. The maximum hydrogen production of 1508.3 mL L(-1) and total lipid concentration of 0.36 g L(-1) were obtained under the optimized mixed ratio (algae:AS) of 30:1, starch concentration of 6 g L(-1) and initial pH of 8. The main soluble metabolites in dark fermentation were acetate and butyrate, most of which can be consumed in co-cultivation. When sweet potato starch wastewater was used as the substrate, the highest COD, TN and TP removal and energy conversion efficiencies reached 80.5%, 88.7%, 80.1% and 34.2%, which were 176%, 178%, 200% and 119% higher than that of the control group (dark fermentation), respectively. This research provided a novel approach and achieved efficient simultaneous energy recovery and nutrients removal from starch wastewater by the co-culture system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Immobilized oleaginous microalgae for production of lipid and phytoremediation of secondary effluent from palm oil mill in fluidized bed photobioreactor.

PubMed

Cheirsilp, Benjamas; Thawechai, Tipawan; Prasertsan, Poonsuk

2017-10-01

Oleaginous microalga Nannochloropsis sp. was immobilized in alginate gel beads and cultivated under optimal conditions that their growth and lipid production were comparable to those of free cells. The immobilized cells were used in phytoremediation of secondary effluent from palm oil mill and easily recovered by simple sieving method. The immobilized cells contributed to removal of nitrogen and phosphorus >90% and CO 2 mitigation >99%. They also gave the biomass and lipid production of 1.300±0.050g/L and 0.356±0.097g/L, respectively. The repeated-batch cultivation improved the biomass and lipid production by 2.66 folds and 1.41 folds, respectively. The scale up in 3L-fluidized bed photobioreactor gave the maximum biomass of 3.280±0.049g/L and lipid production of 0.362±0.010g/L. Fatty acid compositions of Nannochloropsis sp. lipids showed their suitability as biodiesel feedstocks. This system not only contributes as tertiary treatment of industrial effluent and CO 2 mitigation but also low-cost production of renewable energy. Copyright © 2017 Elsevier Ltd. All rights reserved.

An economical device for carbon supplement in large-scale micro-algae production.

PubMed

Su, Zhenfeng; Kang, Ruijuan; Shi, Shaoyuan; Cong, Wei; Cai, Zhaoling

2008-10-01

One simple but efficient carbon-supplying device was designed and developed, and the correlative carbon-supplying technology was described. The absorbing characterization of this device was studied. The carbon-supplying system proved to be economical for large-scale cultivation of Spirulina sp. in an outdoor raceway pond, and the gaseous carbon dioxide absorptivity was enhanced above 78%, which could reduce the production cost greatly.

A Simple Approach to the Study of Attached Micro-Algae.

ERIC Educational Resources Information Center

Bell, Derek; Bell, J. Wendy

1980-01-01

Describes a modification in the use of artificial substrates to study attached micro-algae. Apparatus is based on glass microscope slides immersed in natural water environments; biomass and primary productivity are assessed by measurement of alpha-chlorophyll. Describes use in studies of colonization, succession, and populational fluctuation. (CS)

Sorting cells of the microalga Chlorococcum littorale with increased triacylglycerol productivity.

PubMed

Cabanelas, Iago Teles Dominguez; van der Zwart, Mathijs; Kleinegris, Dorinde M M; Wijffels, René H; Barbosa, Maria J

2016-01-01

Despite extensive research in the last decades, microalgae are still only economically feasible for high valued markets. Strain improvement is a strategy to increase productivities, hence reducing costs. In this work, we focus on microalgae selection: taking advantage of the natural biological variability of species to select variations based on desired characteristics. We focused on triacylglycerol (TAG), which have applications ranging from biodiesel to high-value omega-3 fatty-acids. Hence, we demonstrated a strategy to sort microalgae cells with increased TAG productivity. 1. We successfully identified sub-populations of cells with increased TAG productivity using Fluorescence assisted cell sorting (FACS). 2. We sequentially sorted cells after repeated cycles of N-starvation, resulting in five sorted populations (S1-S5). 3. The comparison between sorted and original populations showed that S5 had the highest TAG productivity [0.34 against 0.18 g l(-1) day(-1) (original), continuous light]. 4. Original and S5 were compared in lab-scale reactors under simulated summer conditions confirming the increased TAG productivity of S5 (0.4 against 0.2 g l(-1) day(-1)). Biomass composition analyses showed that S5 produced more biomass under N-starvation because of an increase only in TAG content and, flow cytometry showed that our selection removed cells with lower efficiency in producing TAGs. All combined, our results present a successful strategy to improve the TAG productivity of Chlorococcum littorale, without resourcing to genetic manipulation or random mutagenesis. Additionally, the improved TAG productivity of S5 was confirmed under simulated summer conditions, highlighting the industrial potential of S5 for microalgal TAG production.

Environmental quality assessment using microalgae structures adjacent fish faming at Setoko Island, Batam City, Kepulaun Riau Province

NASA Astrophysics Data System (ADS)

Hariyati, Riche; Putro, Sapto

2018-05-01

Along with the increasing challenges that come with the demand for national and international fisheries’ products and the potential emergence of various environmental concerns, various efforts have been made to increase production capacity through extensification and intensification programs. This study aimed to assess the environmental quality and the level of disturbance in the floating net cage aquaculture area based on the microalgae community structure. The research was conducted from August to October 2017 at the water ecosystem used for aquaculture at Setoko Island, Batam City, Kepulauan Riau Province. Purposive random sampling was used by determining 3 sampling stations with three replicates. Data was analyzed using saprobic, Shanon-Wiener (H’) diversity, abundance and domination indices. The result showed that 13 genus microalgae (bawal fish fish farming), 9 genus (fish farming kakap) and 11 genus of microalgae (kerapu fish farming ) consisting of Chlorophyta, Chyanophyta Chrysophyta and Dinophyta were recorded. The value of H’ index at the farming area ranged from 0.73 to 1.5. Microalgae abundance was dominated by Phacus sp, Coscinodiscus sp, Climacosphenia sp and Spirogyra sp. Based on the saprobic index, the farm area has an index value of 1.92, thus it can be refferred to as the oligo/β-meso-saprobic phase, indicating light disturbance by organic enrichment.

Neutral lipid accumulation at elevated temperature in conditional mutants of two microalgae species.

PubMed

Yao, Shuo; Brandt, Anders; Egsgaard, Helge; Gjermansen, Claes

2012-12-01

Triacylglycerols, an energy storage compound in microalgae, are known to be accumulated after nitrogen starvation of microalgae cells. Microalgae could be of importance for future biodiesel production due to their fast growth rate and high oil content. In collections of temperature sensitive mutants of Chlamydomonas reinhardtii and Chlorella vulgaris, nine out of fourty-one mutants in C. reinhardtii and eleven out of fifty-three mutants in C. vulgaris contained increased amounts of neutral lipids, predominantly as triacylglycerols. Upon temperature induced cell-cycle arrest, these mutants showed enlarged cellular volume compared with the wild type. The C. reinhardtii mutants were analyzed further and one type of mutants displayed a shift in lipid composition from polar membrane lipids to neutral lipids after a temperature up-shift, while the second type of mutants accumulated more total lipid per cell, predominantly as neutral lipids as compared with the wild type. Three C. reinhardtii mutants were analyzed further and found to be arrested after DNA synthesis but prior to cell division in the cell cycle. These mutants will be useful in order to further understand neutral lipid accumulation in microalgae and suggest possibilities for biodiesel production by specific induction of lipid accumulation in miroalgal cultures by cell-cycle inhibition. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

Enhanced bioenergy recovery from oil-extracted microalgae residues via two-step H2/CH4 or H2/butanol anaerobic fermentation.

PubMed

Cheng, Hai-Hsuan; Whang, Liang-Ming; Wu, Shu-Hsien

2016-03-01

Algae-based biodiesel is considered a promising alternative energy; therefore, the treatment of microalgae residues would be necessary. Anaerobic processes can be used for treating oil-extracted microalgae residues (OMR) and at the same time for recovering bioenergy. In this study, anaerobic batch experiments were conducted to evaluate the potential of recovering bioenergy, in the forms of butanol, H2, or CH4, from pretreated OMR. Using pretreated OMR as the only substrate, a butanol yield of 0.086 g/g-carbohydrate was obtained at carbohydrate of 40 g/L. With supplemented butyrate, a highest butanol yield of 0.192 g/g-carbohydrate was achieved at pretreated OMR containing 25 g/L of carbohydrate with 15 g/L of butyrate addition, attaining the highest energy yield of 3.92 kJ/g-OMR and energy generation rate of 0.65 kJ/g-OMR/d. CH4 production from pretreated OMR attained an energy yield of 8.83 kJ/g-OMR, but energy generation rate required further improvement. H2 production alone from pretreated OMR might not be attractive regarding energy yield, but it attained a superb energy generation rate of 0.68 kJ/g-OMR/d by combining H2 production from pretreated OMR and butanol production from pretreated OMR with supplementary butyrate from H2 fermentation supernatant. This study demonstrated an integrated system as an option for treating OMR and recovering bioenergy. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Lipid Production from Nannochloropsis

PubMed Central

Ma, Xiao-Nian; Chen, Tian-Peng; Yang, Bo; Liu, Jin; Chen, Feng

2016-01-01

Microalgae are sunlight-driven green cell factories for the production of potential bioactive products and biofuels. Nannochloropsis represents a genus of marine microalgae with high photosynthetic efficiency and can convert carbon dioxide to storage lipids mainly in the form of triacylglycerols and to the ω-3 long-chain polyunsaturated fatty acid eicosapentaenoic acid (EPA). Recently, Nannochloropsis has received ever-increasing interests of both research and public communities. This review aims to provide an overview of biology and biotechnological potential of Nannochloropsis, with the emphasis on lipid production. The path forward for the further exploration of Nannochloropsis for lipid production with respect to both challenges and opportunities is also discussed. PMID:27023568

Nuclear transformation of eukaryotic microalgae: historical overview, achievements and problems.

PubMed

León, Rosa; Fernández, Emilio

2007-01-01

Transformation of microalgae is a first step in their use for biotechnological applications involving foreign protein production or molecular modifications of specific cell metabolic pathways. Since the first reliable achievements of nuclear transformation in Chlamydomonas, other eukaryotic microalgae have become transformed with molecular markers that allow a direct selection. Different methods--glass beads, electroporation, particle bombardment, or Agrobacterium--and constructions have been set up in several organisms and successfully used. However, some problems associated with efficiency, integration, or stability of the transgenes still persist and are analysed herein. Though the number of microalgae species successfully transformed is not very high, prospects for transformation of many more are good enough on the basis of what has been achieved so far.

Effect of pre-treatments on the production of biofuels from Phaeodactylum tricornutum.

PubMed

Caporgno, M P; Olkiewicz, M; Torras, C; Salvadó, J; Clavero, E; Bengoa, C

2016-07-15

Several characteristics make Phaeodactylum tricornutum potential candidate for biofuels production such as methane and biodiesel. For this reason, some alternatives are evaluated in this manuscript to improve the conversion of this microalgae into methane. One of these alternatives is the addition of sewage sludge to Phaeodactylum tricornutum for anaerobic co-digestion. Although the co-digestion resulted in lack of synergy, the absence of inhibition indicated that both substrates could be co-digested under certain circumstances, for example if microalgae are cultivated for wastewater treatment purposes. The extraction of lipids using organic solvents has been evaluated for biodiesel production but also as a pre-treatment for anaerobic digestion. The results revealed that the type of solvent influences lipid and biodiesel yields. The high polarity of the mixture methanol/hexane increased the lipid and the biodiesel yields from 10 ± 1 to 53 ± 2 gLipids/100 gVS and from 7 ± 1 to 11 ± 1 gBiodiesel/100 gVS compared with hexane. However, none of these solvents affected the composition of biodiesel. Regarding the methane production after the extraction, it yielded 257 ± 8 and 180 ± 6 mLCH4/gVS from lipid-extracted P. tricornutum using hexane and methanol/hexane respectively. The methane production from the raw microalga was 258 ± 5 mLCH4/gVS in the same experiment. The difference in methane production, mainly after the extraction with methanol/hexane, was a consequence of the changes in the composition of the microalgae after extraction. The extraction did not influence the biodegradability. The ultrasonic pre-treatment prior anaerobic digestion completely disrupted the microalgae cells, but the solubilisation of the organic fraction was scarce (<9.5%). The methane production from pre-treated samples was barely 10-11% higher than the obtained from non pre-treated samples, indicating that the refractory nature of the organic fraction in P. tricornutum is the main obstacle for the methane production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Accelerated triacylglycerol production and altered fatty acid composition in oleaginous microalga Neochloris oleoabundans by overexpression of diacylglycerol acyltransferase 2.

PubMed

Klaitong, Paeka; Fa-Aroonsawat, Sirirat; Chungjatupornchai, Wipa

2017-04-12

Microalgae are promising sources of lipid triacylglycerol (TAG) for biodiesel production. However, to date, microalgal biodiesel is technically feasible, but not yet economically viable. Increasing TAG content and productivity are important to achieve economic viability of microalgal biodiesel. To increase TAG content, oleaginous microalga Neochloris oleoabundans was genetically engineered with an endogenous key enzyme diacylglycerol acyltransferase 2 (NeoDGAT2) responsible for TAG biosynthesis. The integration of NeoDGAT2 expression cassettes in N. oleoabundans transformant was confirmed by PCR. The neutral lipid accumulation in the transformant detected by Nile red staining was accelerated and 1.9-fold higher than in wild type; the lipid bodies in the transformant visualized under fluorescence microscope were also larger. The NeoDGAT2 transcript was two-fold higher in the transformant than wild type. Remarkably higher lipid accumulation was found in the transformant than wild type: total lipid content increased 1.6-to 2.3-fold up to 74.5 ± 4.0% dry cell weight (DCW) and total lipid productivity increased 1.6- to 3.2-fold up to 14.6 ± 2.0 mg/L/day; while TAG content increased 1.8- to 3.2-fold up to 46.1 ± 1.6% DCW and TAG productivity increased 1.6- to 4.3-fold up to 8.9 ± 1.3 mg/L/day. A significantly altered fatty acid composition was detected in the transformant compared to wild type; the levels of saturated fatty acid C16:0 increased double to 49%, whereas C18:0 was reduced triple to 6%. Long-term stability was observed in the transformant continuously maintained in solid medium over 100 generations in a period of about 4 years. Our results demonstrate the increased TAG content and productivity in N. oleoabundans by NeoDGAT2 overexpression that may offer the first step towards making microalgae an economically feasible source for biodiesel production. The strategy for genetically improved microalga presented in this study can be applied to other microalgal species possessing desired characteristics for industrial biofuel production.

Microalgae for economic applications: advantages and perspectives for bioethanol

DOE PAGES

Simas-Rodrigues, Cíntia; Villela, Helena D. M.; Martins, Aline P.; ...

2015-04-04

Renewable energy has attracted significant interest in recent years as a result of sustainability, environmental impact, and socio-economic considerations. Given existing technological knowledge and based on projections relating to biofuels derived from microalgae, microalgal feedstock is considered to be one of the most important renewable energy sources potentially available for industrial production. Finally and therefore, this paper examines microalgal bioethanol technology, which converts biomass from microalgae to fuel, the chemical processes involved, and possible ways of increasing the bioethanol yield, such as abiotic factors and genetic manipulation of fermenting organisms.

Potential land competition between open-pond microalgae production and terrestrial dedicated feedstock supply systems in the U.S.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Langholtz, Matthew H.; Coleman, Andre M.; Eaton, Laurence M.

Biofuels produced from both terrestrial and algal biomass feedstocks can contribute to energy security while providing economic, environmental, and social benefits. To assess the potential for land competition between these two feedstock types in the United States, we evaluate a scenario in which 41.5 x 109 L yr-1 of second-generation biofuels are produced on pastureland, the most likely land base where both feedstock types may be deployed. This total includes 12.0 x 109 L yr-1 of biofuels from open-pond microalgae production and 29.5 x 109 L yr-1 of biofuels from terrestrial dedicated feedstock supply systems. Under these scenarios, open-pond microalgaemore » production is projected to use 1.2 million ha of private pastureland, while terrestrial dedicated feedstock supply systems would use 14.0 million ha of private pastureland. A spatial meta-analysis indicates that potential competition for land under these scenarios would be concentrated in 110 counties, containing 1.0 and 1.7 million hectares of algal and terrestrial dedicated feedstock production, respectively. A land competition index applied to these 110 counties suggests that 38 to 59 counties could experience competition for upwards of 40% of a county’s pastureland. However, this combined 2.7 million ha represents only 2%-5% of total pastureland in the U.S., with the remaining 12.5 million ha of algal or terrestrial dedicated feedstock production on pastureland in non-competing areas.« less

Enhanced growth and fatty acid accumulation of microalgae Scenedesmus sp. LX1 by two types of auxin.

PubMed

Dao, Guo-Hua; Wu, Guang-Xue; Wang, Xiao-Xiong; Zhuang, Lin-Lan; Zhang, Tian-Yuan; Hu, Hong-Ying

2018-01-01

Microalgae are potential candidates for the production of valuable products, such as renewable biodiesel, health products and pigments. However, low biomass productivity has restricted their large-scale applications. In this study, the effects of two auxins (one natural type of indole-3-acetic acid (IAA) and the other synthetic type of 2,4-dichlorophenoxyacetic acid (2,4-D)) on the growth and fatty acid methyl esters (FAMEs) production of a freshwater microalgae Scenedesmus sp. LX1 were investigated. Both auxins showed a "low dosage-promotion and high dosage-inhibition" effect on the growth and FAMEs accumulation. The optimum dosage of IAA and 2,4-D were 1mgL -1 and 0.1mgL -1 , respectively. Moreover, the IAA could increase the monounsaturated fatty acid content. The auxins may promote the growth by enhancing the photosynthetic activity through increasing chlorophyll contents. Therefore, auxin significantly enhanced microalgal growth and FAMEs accumulation, and has a potential for application in developing efficient microalgal cultivation. Copyright © 2017. Published by Elsevier Ltd.

Physiology limits commercially viable photoautotrophic production of microalgal biofuels.

PubMed

Kenny, Philip; Flynn, Kevin J

2017-01-01

Algal biofuels have been offered as an alternative to fossil fuels, based on claims that microalgae can provide a highly productive source of compounds as feedstocks for sustainable transport fuels. Life cycle analyses identify algal productivity as a critical factor affecting commercial and environmental viability. Here, we use mechanistic modelling of the biological processes driving microalgal growth to explore optimal production scenarios in an industrial setting, enabling us to quantify limits to algal biofuels potential. We demonstrate how physiological and operational trade-offs combine to restrict the potential for solar-powered algal-biodiesel production in open ponds to a ceiling of ca. 8000 L ha -1 year -1 . For industrial-scale operations, practical considerations limit production to ca. 6000 L ha -1 year -1 . According to published economic models and life cycle analyses, such production rates cannot support long-term viable commercialisation of solar-powered cultivation of natural microalgae strains exclusively as feedstock for biofuels. The commercial viability of microalgal biofuels depends critically upon limitations in microalgal physiology (primarily in rates of C-fixation); we discuss the scope for addressing this bottleneck concluding that even deployment of genetically modified microalgae with radically enhanced characteristics would leave a very significant logistical if not financial burden.

Microalgal production--a close look at the economics.

PubMed

Norsker, Niels-Henrik; Barbosa, Maria J; Vermuë, Marian H; Wijffels, René H

2011-01-01

Worldwide, microalgal biofuel production is being investigated. It is strongly debated which type of production technology is the most adequate. Microalgal biomass production costs were calculated for 3 different micro algal production systems operating at commercial scale today: open ponds, horizontal tubular photobioreactors and flat panel photobioreactors. For the 3 systems, resulting biomass production costs including dewatering, were 4.95, 4.15 and 5.96 € per kg, respectively. The important cost factors are irradiation conditions, mixing, photosynthetic efficiency of systems, medium- and carbon dioxide costs. Optimizing production with respect to these factors, a price of € 0.68 per kg resulted. At this cost level microalgae become a promising feedstock for biodiesel and bulk chemicals. Photobioreactors may become attractive for microalgal biofuel production. Copyright © 2010 Elsevier Inc. All rights reserved.

Towards sustainable sources for omega-3 fatty acids production.

PubMed

Adarme-Vega, T Catalina; Thomas-Hall, Skye R; Schenk, Peer M

2014-04-01

Omega-3 fatty acids eicosapentaenoic acid (EPA) and docohexaenoic acid (DHA), provide significant health benefits for brain function/development and cardiovascular conditions. However, most EPA and DHA for human consumption is sourced from small fatty fish caught in coastal waters and, with depleting global fish stocks, recent research has been directed towards more sustainable sources. These include aquaculture with plant-based feeds, krill, marine microalgae, microalgae-like protists and genetically-modified plants. To meet the increasing demand for EPA and DHA, further developments are needed towards land-based sources. In particular large-scale cultivation of microalgae and plants is likely to become a reality with expected reductions in production costs, yield increasese and the adequate addressing of genetically modified food acceptance issues. Copyright © 2013 Elsevier Ltd. All rights reserved.

Establishing Chlamydomonas reinhardtii as an industrial biotechnology host

PubMed Central

Scaife, Mark A; Nguyen, Ginnie TDT; Rico, Juan; Lambert, Devinn; Helliwell, Katherine E; Smith, Alison G

2015-01-01

Microalgae constitute a diverse group of eukaryotic unicellular organisms that are of interest for pure and applied research. Owing to their natural synthesis of value-added natural products microalgae are emerging as a source of sustainable chemical compounds, proteins and metabolites, including but not limited to those that could replace compounds currently made from fossil fuels. For the model microalga, Chlamydomonas reinhardtii, this has prompted a period of rapid development so that this organism is poised for exploitation as an industrial biotechnology platform. The question now is how best to achieve this? Highly advanced industrial biotechnology systems using bacteria and yeasts were established in a classical metabolic engineering manner over several decades. However, the advent of advanced molecular tools and the rise of synthetic biology provide an opportunity to expedite the development of C. reinhardtii as an industrial biotechnology platform, avoiding the process of incremental improvement. In this review we describe the current status of genetic manipulation of C. reinhardtii for metabolic engineering. We then introduce several concepts that underpin synthetic biology, and show how generic parts are identified and used in a standard manner to achieve predictable outputs. Based on this we suggest that the development of C. reinhardtii as an industrial biotechnology platform can be achieved more efficiently through adoption of a synthetic biology approach. Significance Statement Chlamydomonas reinhardtii offers potential as a host for the production of high value compounds for industrial biotechnology. Synthetic biology provides a mechanism to generate generic, well characterised tools for application in the rational genetic manipulation of organisms: if synthetic biology principles were adopted for manipulation of C. reinhardtii, development of this microalga as an industrial biotechnology platform would be expedited. PMID:25641561

Microalgal biomass production pathways: evaluation of life cycle environmental impacts

PubMed Central

2013-01-01

Background Microalgae are touted as an attractive alternative to traditional forms of biomass for biofuel production, due to high productivity, ability to be cultivated on marginal lands, and potential to utilize carbon dioxide (CO2) from industrial flue gas. This work examines the fossil energy return on investment (EROIfossil), greenhouse gas (GHG) emissions, and direct Water Demands (WD) of producing dried algal biomass through the cultivation of microalgae in Open Raceway Ponds (ORP) for 21 geographic locations in the contiguous United States (U.S.). For each location, comprehensive life cycle assessment (LCA) is performed for multiple microalgal biomass production pathways, consisting of a combination of cultivation and harvesting options. Results Results indicate that the EROIfossil for microalgae biomass vary from 0.38 to 1.08 with life cycle GHG emissions of −46.2 to 48.9 (g CO2 eq/MJ-biomass) and direct WDs of 20.8 to 38.8 (Liters/MJ-biomass) over the range of scenarios analyzed. Further anaylsis reveals that the EROIfossil for production pathways is relatively location invariant, and that algae’s life cycle energy balance and GHG impacts are highly dependent on cultivation and harvesting parameters. Contrarily, algae’s direct water demands were found to be highly sensitive to geographic location, and thus may be a constraining factor in sustainable algal-derived biofuel production. Additionally, scenarios with promising EROIfossil and GHG emissions profiles are plagued with high technological uncertainty. Conclusions Given the high variability in microalgae’s energy and environmental performance, careful evaluation of the algae-to-fuel supply chain is necessary to ensure the long-term sustainability of emerging algal biofuel systems. Alternative production scenarios and technologies may have the potential to reduce the critical demands of biomass production, and should be considered to make algae a viable and more efficient biofuel alternative. PMID:23786775

Ammonia tolerant inocula provide a good base for anaerobic digestion of microalgae in third generation biogas process.

PubMed

Mahdy, Ahmed; Fotidis, Ioannis A; Mancini, Enrico; Ballesteros, Mercedes; González-Fernández, Cristina; Angelidaki, Irini

2017-02-01

This study investigated the ability of an ammonia-acclimatized inoculum to digest efficiently protein-rich microalgae for continuous 3rd generation biogas production. Moreover, we investigated whether increased C/N ratio could alleviate ammonia toxicity. The biochemical methane potential (BMP) of five different algae (Chlorella vulgaris)/manure (cattle) mixtures showed that the mixture of 80/20 (on VS basis) resulted in the highest BMP value (431mLCH 4 gVS -1 ), while the BMP of microalgae alone (100/0) was 415mLCH 4 gVS -1 . Subsequently, anaerobic digestion of those two substrates was tested in continuous stirred tank reactors (CSTR). Despite of the high ammonium levels (3.7-4.2g NH 4 + -NL -1 ), CSTR reactors using ammonia tolerant inoculum resulted in relatively high methane yields (i.e. 77.5% and 84% of the maximum expected, respectively). These results demonstrated that ammonia tolerant inocula could be a promising approach to successfully digest protein-rich microalgae and achieve a 3rd generation biogas production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Co-generation of biohydrogen and biomethane through two-stage batch co-fermentation of macro- and micro-algal biomass.

PubMed

Ding, Lingkan; Cheng, Jun; Xia, Ao; Jacob, Amita; Voelklein, Markus; Murphy, Jerry D

2016-10-01

Aquatic micro-algae can be used as feedstocks for gaseous biofuel production via biological fermentation. However, micro-algae usually have low C/N ratios, which are not advantageous for fermentation. In this study, carbon-rich macro-algae (Laminaria digitata) mixed with nitrogen-rich micro-algae (Chlorella pyrenoidosa and Nannochloropsis oceanica) were used to maintain a suitable C/N ratio of 20 for a two-stage process combining hydrogen and methane fermentation. Co-fermentation of L. digitata and micro-algae facilitated hydrolysis and acidogenesis, resulting in hydrogen yields of 94.5-97.0mL/gVS; these values were 15.5-18.5% higher than mono-fermentation using L. digitata. Through the second stage of methane co-fermentation, a large portion of energy remaining in the hydrogenogenic effluents was recovered in the form of biomethane. The two-stage batch co-fermentation markedly increased the energy conversion efficiencies (ECEs) from 4.6-6.6% during the hydrogen fermentation to 57.0-70.9% in the combined hydrogen and methane production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cultivation of Chlorella vulgaris JSC-6 with swine wastewater for simultaneous nutrient/COD removal and carbohydrate production.

PubMed

Wang, Yue; Guo, Wanqian; Yen, Hong-Wei; Ho, Shih-Hsin; Lo, Yung-Chung; Cheng, Chieh-Lun; Ren, Nanqi; Chang, Jo-Shu

2015-12-01

Swine wastewater, containing a high concentration of COD and ammonia nitrogen, is suitable for the growth of microalgae, leading to simultaneous COD/nutrients removal from the wastewater. In this study, an isolated carbohydrate-rich microalga Chlorella vulgaris JSC-6 was adopted to perform swine wastewater treatment. Nearly 60-70% COD removal and 40-90% NH3-N removal was achieved in the mixotrophic and heterotrophic culture, depending on the dilution ratio of the wastewater, while the highest removal percentage was obtained with 20-fold diluted wastewater. Mixotrophic cultivation by using fivefold diluted wastewater resulted in the highest biomass concentration of 3.96 g/L. The carbohydrate content of the microalga grown on the wastewater can reach up to 58% (per dry weight). The results indicated that the microalgae-based wastewater treatment can efficiently reduce the nutrients and COD level, and the resulting microalgal biomass had high carbohydrate content, thereby having potential applications for the fermentative production of biofuels or chemicals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Treatment of recalcitrant wastewater from ethanol and citric acid production using the microalga Chlorella vulgaris and the macrophyte Lemna minuscula.

PubMed

Valderrama, Luz T; Del Campo, Claudia M; Rodriguez, Claudia M; de- Bashan, Luz E; Bashan, Yoav

2002-10-01

Laboratory-scale experiments were performed to develop a procedure for biological treatment of recalcitrant anaerobic industrial effluent (from ethanol and citric acid production) using first the microalga Chlorella vulgaris followed by the macrophyte Lemna minuscula. This recalcitrant dark-colored wastewater, containing high levels of organic matter and low pH, prevents the growth of microalgae and macrophytes, and therefore, could not be treated by them. Therefore, the wastewater was diluted to 10% of the original concentration with wash water from the production line. Within 4 days of incubation in the wastewater, C. vulgaris population grew from 5 x 10(5) to 2 x 10(6) cells/mL. This culture reduced ammonium ion (71.6%), phosphorus (28%), and chemical oxygen demand (COD) (61%), and dissolved a floating microbial biofilm after 5 days of incubation. Consequently, L. minuscule was able to grow in the treated wastewater (from 7 to 14 g/bioreactor after 6 days), precipitated the microalgal cells (by shading the culture), and reduced other organic matter and color (up to 52%) after an additional 6 days of incubation. However, L. minuscula did not improve removal of nutrients. This study demonstrates the feasibility of combining microalgae and macrophytes for bioremediation of recalcitrant industrial wastewater.

Microalgal Cultivation in Secondary Effluent: Recent Developments and Future Work

PubMed Central

Lv, Junping; Feng, Jia; Liu, Qi; Xie, Shulian

2017-01-01

Eutrophication of water catchments and the greenhouse effect are major challenges in developing the global economy in the near future. Secondary effluents, containing high amounts of nitrogen and phosphorus, need further treatment before being discharged into receiving water bodies. At the same time, new environmentally friendly energy sources need to be developed. Integrating microalgal cultivation for the production of biodiesel feedstock with the treatment of secondary effluent is one way of addressing both issues. This article provides a comprehensive review of the latest progress in microalgal cultivation in secondary effluent to remove pollutants and accumulate lipids. Researchers have discovered that microalgae remove nitrogen and phosphorus effectively from secondary effluent, accumulating biomass and lipids in the process. Immobilization of appropriate microalgae, and establishing a consortium of microalgae and/or bacteria, were both found to be feasible ways to enhance pollutant removal and lipid production. Demonstrations of pilot-scale microalgal cultures in secondary effluent have also taken place. However there is still much work to be done in improving pollutants removal, biomass production, and lipid accumulation in secondary effluent. This includes screening microalgae, constructing the consortium, making use of flue gas and nitrogen, developing technologies related to microalgal harvesting, and using lipid-extracted algal residues (LEA). PMID:28045437

Influence of nitrogen on growth, biomass composition, production, and properties of polyhydroxyalkanoates (PHAs) by microalgae.

PubMed

Costa, Samantha Serra; Miranda, Andréa Lobo; Andrade, Bianca Bomfim; Assis, Denilson de Jesus; Souza, Carolina Oliveira; de Morais, Michele Greque; Costa, Jorge Alberto Vieira; Druzian, Janice Izabel

2018-05-12

This study sought to evaluate influence of nitrogen availability on cell growth, biomass composition, production, and the properties of polyhydroxyalkanoates during cultivation of microalgae Chlorella minutissima, Synechococcus subsalsus, and Spirulina sp. LEB-18. The cellular growth of microalgae reduced with the use of limited nitrogen medium, demonstrating that nitrogen deficiency interferes with the metabolism of microorganisms and the production of biomass. The biochemical composition of microalgae was also altered, which was most notable in the degradation of proteins and chlorophylls and the accumulation of carbonaceous storage molecules such as lipids and polyhydroxyalkanoates. Chlorella minutissima did not produce these polymers even in a nitrogen deficient environment. The largest accumulations of the polyhydroxyalkanoates occurred after a 15 days culture, with a concentration of 16% (dry cell weight) produced by the Synechococcus subsalsus strain and 12% by Spirulina sp. LEB-18. Polyhydroxyalkanoates produced by Synechococcus subsalsus and Spirulina sp. LEB-18 presented different thermal and physical properties, indicating the influence of producing strain on polyhydroxyalkanoates properties. The polymers obtained consisted of long chain monomers with 14 to 18 carbon atoms. This composition is novel, as it has not previously been found in PHAs obtained from Synechococcus subsalsus and Spirulina sp. LEB-18. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of indigo dye effluent on the growth, biomass production and phenotypic plasticity of Scenedesmus quadricauda (Chlorococcales).

PubMed

Chia, Mathias A; Musa, Rilwan I

2014-03-01

The effect of indigo dye effluent on the freshwater microalga Scenedesmus quadricauda ABU12 was investigated under controlled laboratory conditions. The microalga was exposed to different concentrations of the effluent obtained by diluting the dye effluent from 100 to 175 times in bold basal medium (BBM). The growth rate of the microalga decreased as indigo dye effluent concentration increased (p <0.05). The EC50 was found to be 166 dilution factor of the effluent. Chlorophyll a, cell density and dry weight production as biomarkers were negatively affected by high indigo dye effluent concentration, their levels were higher at low effluent concentrations (p <0.05). Changes in coenobia size significantly correlated with the dye effluent concentration. A shift from large to small coenobia with increasing indigo dye effluent concentration was obtained. We conclude that even at low concentrations; effluents from textile industrial processes that use indigo dye are capable of significantly reducing the growth and biomass production, in addition to altering the morphological characteristics of the freshwater microalga S. quadricauda. The systematic reduction in the number of cells per coenobium observed in this study further confirms that environmental stress affects coenobium structure in the genus Scenedesmus, which means it can be considered an important biomarker for toxicity testing.

Progress and Challenges in Microalgal Biodiesel Production.

PubMed

Mallick, Nirupama; Bagchi, Sourav K; Koley, Shankha; Singh, Akhilesh K

2016-01-01

The last decade has witnessed a tremendous impetus on biofuel research due to the irreversible diminution of fossil fuel reserves for enormous demands of transportation vis-a-vis escalating emissions of green house gasses (GHGs) into the atmosphere. With an imperative need of CO2 reduction and considering the declining status of crude oil, governments in various countries have not only diverted substantial funds for biofuel projects but also have introduced incentives to vendors that produce biofuels. Currently, biodiesel production from microalgal biomass has drawn an immense importance with the potential to exclude high-quality agricultural land use and food safe-keeping issues. Moreover, microalgae can grow in seawater or wastewater and microalgal oil can exceed 50-60% (dry cell weight) as compared with some best agricultural oil crops of only 5-10% oil content. Globally, microalgae are the highest biomass producers and neutral lipid accumulators contending any other terrestrial oil crops. However, there remain many hurdles in each and every step, starting from strain selection and lipid accumulation/yield, algae mass cultivation followed by the downstream processes such as harvesting, drying, oil extraction, and biodiesel conversion (transesterification), and overall, the cost of production. Isolation and screening of oleaginous microalgae is one pivotal important upstream factor which should be addressed according to the need of freshwater or marine algae with a consideration that wild-type indigenous isolate can be the best suited for the laboratory to large scale exploitation. Nowadays, a large number of literature on microalgal biodiesel production are available, but none of those illustrate a detailed step-wise description with the pros and cons of the upstream and downstream processes of biodiesel production from microalgae. Specifically, harvesting and drying constitute more than 50% of the total production costs; however, there are quite a less number of detailed study reports available. In this review, a pragmatic and critical analysis was tried to put forward with the on-going researches on isolation and screening of oleaginous microalgae, microalgal large scale cultivation, biomass harvesting, drying, lipid extraction and finally biodiesel production.

Progress and Challenges in Microalgal Biodiesel Production

PubMed Central

Mallick, Nirupama; Bagchi, Sourav K.; Koley, Shankha; Singh, Akhilesh K.

2016-01-01

The last decade has witnessed a tremendous impetus on biofuel research due to the irreversible diminution of fossil fuel reserves for enormous demands of transportation vis-a-vis escalating emissions of green house gasses (GHGs) into the atmosphere. With an imperative need of CO2 reduction and considering the declining status of crude oil, governments in various countries have not only diverted substantial funds for biofuel projects but also have introduced incentives to vendors that produce biofuels. Currently, biodiesel production from microalgal biomass has drawn an immense importance with the potential to exclude high-quality agricultural land use and food safe-keeping issues. Moreover, microalgae can grow in seawater or wastewater and microalgal oil can exceed 50–60% (dry cell weight) as compared with some best agricultural oil crops of only 5–10% oil content. Globally, microalgae are the highest biomass producers and neutral lipid accumulators contending any other terrestrial oil crops. However, there remain many hurdles in each and every step, starting from strain selection and lipid accumulation/yield, algae mass cultivation followed by the downstream processes such as harvesting, drying, oil extraction, and biodiesel conversion (transesterification), and overall, the cost of production. Isolation and screening of oleaginous microalgae is one pivotal important upstream factor which should be addressed according to the need of freshwater or marine algae with a consideration that wild-type indigenous isolate can be the best suited for the laboratory to large scale exploitation. Nowadays, a large number of literature on microalgal biodiesel production are available, but none of those illustrate a detailed step-wise description with the pros and cons of the upstream and downstream processes of biodiesel production from microalgae. Specifically, harvesting and drying constitute more than 50% of the total production costs; however, there are quite a less number of detailed study reports available. In this review, a pragmatic and critical analysis was tried to put forward with the on-going researches on isolation and screening of oleaginous microalgae, microalgal large scale cultivation, biomass harvesting, drying, lipid extraction and finally biodiesel production. PMID:27446055

Polishing of POME by Chlorella sp. in suspended and immobilized system

NASA Astrophysics Data System (ADS)

Lahin, F. A.; Sarbatly, R.; Suali, E.

2016-06-01

The effect of using suspended and immobilized growth of Chlorella sp. to treat POME was studied. Cotton and nylon ropes were used as the immobilization material in a rotating microalgae biofilm reactor. The result showed that POME treated in suspended growth system was able to remove 81.9% and 55.5% of the total nitrogen (TN) and total phosphorus (TP) respectively. Whereas the immobilized system showed lower removal of 77.22% and 53.02% for TN and TP. Lower performance of immobilized microalgae is due to the limited light penetration and supply of CO2 inside the immobilization materials. The rotating microalgae biofilm reactor was able to reduce the biochemical oxygen demand (BOD) to 90 mg/L and chemical oxygen demand (COD) to 720 mg/L. Higher BOD and COD reading were obtained in suspended growth due to the presence of small number of microalgae cell in the samples. This study shows that suspended growth system is able to remove higher percentages of nitrogen and phosphorus. However, an efficient separation method such as membrane filtration is required to harvest the cultivated microalgae cell to avoid organic matter release into water bodies.

The Effects of Microalgae as Live Food for Brachionus plicatilis (Rotifer) in Intensive Culture System

PubMed Central

Rahman, Abdull Razak Abd; Cob, Zaidi Che; Jamari, Zainoddin; Mohamed, Abdul Majid; Toda, Tatsuki; Ross, Othman Haji

2018-01-01

Brachionus plicatilis is used to feed fish and crustacean larvae in the aquaculture industry. It is well established that the type of microalgae may influence rotifer production. This experiment was conducted to determine the effect of five different locally available microalgae species at Fisheries Research Institute (FRI), Kampung Pulau Sayak, Kedah, Malaysia on the instantaneous growth rate (μ) of rotifer. Nannochloris sp., Tetraselmis sp., Isochrysis sp., Chlorella sp., and Nannochloropsis sp. were used as feed at different algae densities (0.1, 0.3, 0.7 and 1.5 × 106 cells/ml) and culture volumes (20, 70 and 210 ml). At algae densities ranging from 0.3 to 1.5 × 106 cells/ml, an average μ value of more than 0.90 per day were recorded for all algae species. However, at density of 0.1 × 106 cells/ml, only Tetraselmis sp. resulted in the significantly highest μ value compared with others (p < 0.05). In terms of volume, smaller culture volume of Tetraselmis sp. (20 ml) showed significantly higher μ compared with higher volume (70 and 210 ml cultures). PMID:29644020

Impacts of potassium ferrate(VI) on the growth and organic matter accumulation, production, and structural changes in the cyanobacterium Microcystis aeruginosa.

PubMed

Liu, Shu-Yu; Xu, Jingling; Chen, Wen-Li; David, Berthold E; Wu, Minghong; Ma, Fang

2017-04-01

Cyanobacterial blooms generated by nutrient addition into aquatic systems pose serious risks to ecosystems and human health. Though there are established chemical, physical, and biological means of eradication, more efficient and environmentally friendly measures are desired. This study investigates the effect of potassium ferrate(VI) on the growth and intracellular and extracellular organic matter accumulations of the cyanobacterium Microcystis aeruginosa. Cultures were inoculated with three separate concentrations of potassium ferrate(VI) (3, 15, 30 mg L -1 ) and monitored by measuring chlorophyll-a (Chl-a) and intracellular/extracellular dissolved organic carbon. Results show that ferrate(VI) addition effectively removed the microalgae from the medium, as indicated by the reduction of Chl-a. Organic matter accumulation of the microalgae was also affected by ferrate(VI) treatment; fluorescence EEM spectra show details of changing intracellular dissolved organic matter (IDOM) and extracellular dissolved organic matter (EDOM). A new peak appeared in the EDOM indicating altered humic and proteinaceous compounds. This study demonstrates that ferrate(VI) is a potential treatment for the water contaminated with the toxic microalgae M. aeruginosa.

Nutrient recycling of lipid-extracted waste in the production of an oleaginous thraustochytrid.

PubMed

Lowrey, Joshua; Brooks, Marianne S; Armenta, Roberto E

2016-05-01

Improving the economics of microalgae production for the recovery of microbial oil requires a comprehensive exploration of the measures needed to improve productivity as well as to reduce the overall processing costs. One avenue for cost reduction involves recycling the effluent waste water remaining after lipid extraction. This study investigates the feasibility of recycling those wastes for growing thraustochytrid biomass, a heterotrophic microalgae, where wastes were generated from the enzymatic extraction of the lipids from the cell biomass. It was demonstrated that secondary cultures of the tested thraustochytrid grown in the recycled wastes performed favorably in terms of cell and oil production (20.48 g cells L(-1) and 40.9 % (w/w) lipid) compared to the control (13.63 g cells L(-1) and 56.8 % (w/w) lipid). Further, the significant uptake of solubilized cell material (in the form of amino acids) demonstrated that the recycled waste has the potential for offsetting the need for fresh medium components. These results indicate that the implementation of a nutrient recycling strategy for industrial microalgae production could be possible, with significant added benefits such as conserving water resources, improving production efficiency, and decreasing material inputs.

Production of Spirulina sp by utilization of wastewater from the powder type energy drinks

NASA Astrophysics Data System (ADS)

Sumantri, Indro; Priyambada, Ika Bagus

2015-12-01

Wastewater of energy drink type of powder produced when the the production equipment required cleaning treatment to produce one taste to others. These equipments washed by water, so that, it produced wastewater. It contains high organic substances and classified as high degradable due to food product. The content of wastewater is high carbon and nitrogen substances. Microalgae is an autotrophic microorganism, live without carbon presence, utilized to digest the substances in wastewater especially for nitrogen substances. Spirulina sp is the type of microalgae selected to utilize the wastewater of energy drink, the selection criteria is the size of Spirulina sp is relatively large and easy to separated from its solution. The experiment conducted by cultivate the seeding microalgae with certain nutrients until the certain volume. The synthetic wastewater obtained from one of energy drink type of powder with commercial brand as Kuku Bima Ener-G, the wastewater concentration selected under the close to the real condition of wastewater as basis of COD measurement (6 sachet/L or COD of 12.480mg/L) and aqueous concentration (1 sachet/L or COD of 2080mg/L). The batch experiments with 1L volume conducted and with variable of percent volume of wastewater added in order to observe the growth of microlagae. The response of the microalgae growth obtained by increasing the optical density of the microalgae solution and continued by calculation for the growth rate of microalgae. The result of the experiments indicated that for the aqueous concentration (1 sachet/L or COD of 2080mg/L) the optimum added of wastewater is 40 % with growrate of 0.55/day while for the concentrated wastewater (6 sachet/L or COD of 12.480mg/L), the optimum condition is 25 % wastewater added with growth rate of 0.43/day.

Characterization of the flocculating agent from the spontaneously flocculating microalga Chlorella vulgaris JSC-7.

PubMed

Alam, Md Asraful; Wan, Chun; Guo, Suo-Lian; Zhao, Xin-Qing; Huang, Zih-You; Yang, Yu-Liang; Chang, Jo-Shu; Bai, Feng-Wu

2014-07-01

High cost of biomass recovery is one of the bottlenecks for developing cost-effective processes with microalgae, particularly for the production of biofuels and bio-based chemicals through biorefinery, and microalgal biomass recovery through cell flocculation is a promising strategy. Some microalgae are naturally flocculated whose cells can be harvested by simple sedimentation. However, studies on the flocculating agents synthesized by microalgae cells are still very limited. In this work, the cell flocculation of a spontaneously flocculating microalga Chlorella vulgaris JSC-7 was studied, and the flocculating agent was identified to be cell wall polysaccharides whose crude extract supplemented at low dosage of 0.5 mg/L initiated the more than 80% flocculating rate of freely suspended microalgae C. vulgaris CNW11 and Scenedesmus obliquus FSP. Fourier transform infrared (FTIR) analysis revealed a characteristic absorption band at 1238 cm(-1), which might arise from PO asymmetric stretching vibration of [Formula: see text] phosphodiester. The unique cell wall-associated polysaccharide with molecular weight of 9.86×10(3) g/mol, and the monomers consist of glucose, mannose and galactose with a molecular ratio of 5:5:2. This is the first time to our knowledge that the flocculating agent from C. vulgaris has been characterized, which could provide basis for understanding the cell flocculation of microalgae and breeding of novel flocculating microalgae for cost-effective biomass harvest. Copyright © 2013 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Extremophilic micro-algae and their potential contribution in biotechnology.

PubMed

Varshney, Prachi; Mikulic, Paulina; Vonshak, Avigad; Beardall, John; Wangikar, Pramod P

2015-05-01

Micro-algae have potential as sustainable sources of energy and products and alternative mode of agriculture. However, their mass cultivation is challenging due to low survival under harsh outdoor conditions and competition from other, undesired, species. Extremophilic micro-algae have a role to play by virtue of their ability to grow under acidic or alkaline pH, high temperature, light, CO2 level and metal concentration. In this review, we provide several examples of potential biotechnological applications of extremophilic micro-algae and the ranges of tolerated extremes. We also discuss the adaptive mechanisms of tolerance to these extremes. Analysis of phylogenetic relationship of the reported extremophiles suggests certain groups of the Kingdom Protista to be more tolerant to extremophilic conditions than other taxa. While extremophilic microalgae are beginning to be explored, much needs to be done in terms of the physiology, molecular biology, metabolic engineering and outdoor cultivation trials before their true potential is realized. Copyright © 2014 Elsevier Ltd. All rights reserved.

Co-digestion of cultivated microalgae and sewage sludge from municipal waste water treatment.

PubMed

Olsson, Jesper; Feng, Xin Mei; Ascue, Johnny; Gentili, Francesco G; Shabiimam, M A; Nehrenheim, Emma; Thorin, Eva

2014-11-01

In this study two wet microalgae cultures and one dried microalgae culture were co-digested in different proportions with sewage sludge in mesophilic and thermophilic conditions. The aim was to evaluate if the co-digestion could lead to an increased efficiency of methane production compared to digestion of sewage sludge alone. The results showed that co-digestion with both wet and dried microalgae, in certain proportions, increased the biochemical methane potential (BMP) compared with digestion of sewage sludge alone in mesophilic conditions. The BMP was significantly higher than the calculated BMP in many of the mixtures. This synergetic effect was statistically significant in a mixture containing 63% (w/w VS based) undigested sewage sludge and 37% (w/w VS based) wet algae slurry, which produced 23% more methane than observed with undigested sewage sludge alone. The trend was that thermophilic co-digestion of microalgae and undigested sewage sludge did not give the same synergy. Copyright © 2014 Elsevier Ltd. All rights reserved.

Quantification and characterisation of fatty acid methyl esters in microalgae: Comparison of pretreatment and purification methods.

PubMed

Lage, Sandra; Gentili, Francesco G

2018-06-01

A systematic qualitative and quantitative analysis of fatty acid methyl esters (FAMEs) is crucial for microalgae species selection for biodiesel production. The aim of this study is to identify the best method to assess microalgae FAMEs composition and content. A single-step method, was tested with and without purification steps-that is, separation of lipid classes by thin-layer chromatography (TLC) or solid-phase extraction (SPE). The efficiency of a direct transesterification method was also evaluated. Additionally, the yield of the FAMEs and the profiles of the microalgae samples with different pretreatments (boiled in isopropanol, freezing, oven-dried and freeze-dried) were compared. The application of a purification step after lipid extraction proved to be essential for an accurate FAMEs characterisation. The purification methods, which included TLC and SPE, provided superior results compared to not purifying the samples. Freeze-dried microalgae produced the lowest FAMEs yield. However, FAMEs profiles were generally equivalent among the pretreatments. Copyright © 2018 Elsevier Ltd. All rights reserved.

Photon up-conversion increases biomass yield in Chlorella vulgaris.

PubMed

Menon, Kavya R; Jose, Steffi; Suraishkumar, Gadi K

2014-12-01

Photon up-conversion, a process whereby lower energy radiations are converted to higher energy levels via the use of appropriate phosphor systems, was employed as a novel strategy for improving microalgal growth and lipid productivity. Photon up-conversion enables the utilization of regions of the solar spectrum, beyond the typical photosynthetically active radiation, that are usually wasted or are damaging to the algae. The effects of up-conversion of red light by two distinct sets of up-conversion phosphors were studied in the model microalgae Chlorella vulgaris. Up-conversion by set 1 phosphors led to a 2.85 fold increase in biomass concentration and a 3.2 fold increase in specific growth rate of the microalgae. While up-conversion by set 2 phosphors resulted in a 30% increase in biomass and 12% increase in specific intracellular neutral lipid, while the specific growth rates were comparable to that of the control. Furthermore, up-conversion resulted in higher levels of specific intracellular reactive oxygen species in C. vulgaris. Up-conversion of red light (654 nm) was shown to improve biomass yields in C. vulgaris. In principle, up-conversion can be used to increase the utilization range of the electromagnetic spectrum for improved cultivation of photosynthetic systems such as plants, algae, and microalgae. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Audible sound treatment of the microalgae Picochlorum oklahomensis for enhancing biomass productivity.

PubMed

Cai, Weiming; Dunford, Nurhan Turgut; Wang, Ning; Zhu, Songming; He, Huinong

2016-02-01

It has been reported in the literature that exposure of microalgae cells to audible sound could promote growth. This study examined the effect of sound waves with the frequency of 1100 Hz, 2200 Hz, and 3300 Hz to stimulate the biomass productivity of an Oklahoma native strain, Picochlorum oklahomensis (PO). The effect of the frequency of sound on biomass mass was measured. This study demonstrated that audible sound treatment of the algae cultures at 2200 Hz was the most effective in terms of biomass production and volumetric oil yield. Copyright © 2015 Elsevier Ltd. All rights reserved.

Transcriptome sequencing and annotation of the microalgae Dunaliella tertiolecta: Pathway description and gene discovery for production of next-generation biofuels

PubMed Central

2011-01-01

Background Biodiesel or ethanol derived from lipids or starch produced by microalgae may overcome many of the sustainability challenges previously ascribed to petroleum-based fuels and first generation plant-based biofuels. The paucity of microalgae genome sequences, however, limits gene-based biofuel feedstock optimization studies. Here we describe the sequencing and de novo transcriptome assembly for the non-model microalgae species, Dunaliella tertiolecta, and identify pathways and genes of importance related to biofuel production. Results Next generation DNA pyrosequencing technology applied to D. tertiolecta transcripts produced 1,363,336 high quality reads with an average length of 400 bases. Following quality and size trimming, ~ 45% of the high quality reads were assembled into 33,307 isotigs with a 31-fold coverage and 376,482 singletons. Assembled sequences and singletons were subjected to BLAST similarity searches and annotated with Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) orthology (KO) identifiers. These analyses identified the majority of lipid and starch biosynthesis and catabolism pathways in D. tertiolecta. Conclusions The construction of metabolic pathways involved in the biosynthesis and catabolism of fatty acids, triacylglycrols, and starch in D. tertiolecta as well as the assembled transcriptome provide a foundation for the molecular genetics and functional genomics required to direct metabolic engineering efforts that seek to enhance the quantity and character of microalgae-based biofuel feedstock. PMID:21401935

Ecotoxicological effects of enrofloxacin and its removal by monoculture of microalgal species and their consortium.

PubMed

Xiong, Jiu-Qiang; Kurade, Mayur B; Jeon, Byong-Hun

2017-07-01

Enrofloxacin (ENR), a fluoroquinolone antibiotic, has gained big scientific concern due to its ecotoxicity on aquatic microbiota. The ecotoxicity and removal of ENR by five individual microalgae species and their consortium were studied to correlate the behavior and interaction of ENR in natural systems. The individual microalgal species (Scenedesmus obliquus, Chlamydomonas mexicana, Chlorella vulgaris, Ourococcus multisporus, Micractinium resseri) and their consortium could withstand high doses of ENR (≤1 mg L -1 ). Growth inhibition (68-81%) of the individual microalgae species and their consortium was observed in ENR (100 mg L -1 ) compared to control after 11 days of cultivation. The calculated 96 h EC 50 of ENR for individual microalgae species and microalgae consortium was 9.6-15.0 mg ENR L -1 . All the microalgae could recover from the toxicity of high concentrations of ENR during cultivation. The biochemical characteristics (total chlorophyll, carotenoid, and malondialdehyde) were significantly influenced by ENR (1-100 mg L -1 ) stress. The individual microalgae species and microalgae consortium removed 18-26% ENR at day 11. Although the microalgae consortium showed a higher sensitivity (with lower EC 50 ) toward ENR than the individual microalgae species, the removal efficiency of ENR by the constructed microalgae consortium was comparable to that of the most effective microalgal species. Copyright © 2017 Elsevier Ltd. All rights reserved.

Microalgae community shifts during the biogas upgrading in an alkaline open photobioreactor.

PubMed

Granada-Moreno, C I; Aburto-Medina, A; de Los Cobos Vasconcelos, D; González-Sánchez, A

2017-10-01

To achieve the functional specialization of a microalgae community through operational tuning of an open photobioreactor used for biogas upgrading under alkaline conditions. An open photobioreactor was inoculated with an indigenous microalgae sample from the Texcoco Soda Lake. A microalgae community was adapted to fix CO 2 from synthetic biogas through different culture conditions reaching a maximum of 220 mg CO 2  l -1 per day. Picochlorum sp. and Scenedesmus sp. were identified as the prominent microalgae genera by molecular fingerprinting (partial sequencing of 16S rRNA and 18S rRNA genes) but only the first was detected by microscopy screening. Changes in the microalgae community profile were monitored by a range-weighted richness index, reaching the lowest value when biogas was upgraded. A robust microalgae community in the open photobioreactor was obtained after different culture conditions. The specialization of microalgae community for CO 2 fixation under H 2 S presence was driven by biogas upgrading conditions. The alkaline conditions enhance the CO 2 absorption from biogas and could optimize specialized microalgae communities in the open photobioreactor. Denaturing gradient gel electrophoresis fingerprinting and richness index comparison are useful methods for the evaluation of microalgae community shifts and photosynthetic activity performance, particularly in systems intended for CO 2 removal from biogas where the CO 2 assimilation potential can be related to the microbial richness. © 2017 The Society for Applied Microbiology.

RNAi Knock-Down of LHCBM1, 2 and 3 Increases Photosynthetic H2 Production Efficiency of the Green Alga Chlamydomonas reinhardtii

PubMed Central

Oey, Melanie; Ross, Ian L.; Stephens, Evan; Steinbeck, Janina; Wolf, Juliane; Radzun, Khairul Adzfa; Kügler, Johannes; Ringsmuth, Andrew K.; Kruse, Olaf; Hankamer, Ben

2013-01-01

Single cell green algae (microalgae) are rapidly emerging as a platform for the production of sustainable fuels. Solar-driven H2 production from H2O theoretically provides the highest-efficiency route to fuel production in microalgae. This is because the H2-producing hydrogenase (HYDA) is directly coupled to the photosynthetic electron transport chain, thereby eliminating downstream energetic losses associated with the synthesis of carbohydrate and oils (feedstocks for methane, ethanol and oil-based fuels). Here we report the simultaneous knock-down of three light-harvesting complex proteins (LHCMB1, 2 and 3) in the high H2-producing Chlamydomonas reinhardtii mutant Stm6Glc4 using an RNAi triple knock-down strategy. The resultant Stm6Glc4L01 mutant exhibited a light green phenotype, reduced expression of LHCBM1 (20.6% ±0.27%), LHCBM2 (81.2% ±0.037%) and LHCBM3 (41.4% ±0.05%) compared to 100% control levels, and improved light to H2 (180%) and biomass (165%) conversion efficiencies. The improved H2 production efficiency was achieved at increased solar flux densities (450 instead of ∼100 µE m−2 s−1) and high cell densities which are best suited for microalgae production as light is ideally the limiting factor. Our data suggests that the overall improved photon-to-H2 conversion efficiency is due to: 1) reduced loss of absorbed energy by non-photochemical quenching (fluorescence and heat losses) near the photobioreactor surface; 2) improved light distribution in the reactor; 3) reduced photoinhibition; 4) early onset of HYDA expression and 5) reduction of O2-induced inhibition of HYDA. The Stm6Glc4L01 phenotype therefore provides important insights for the development of high-efficiency photobiological H2 production systems. PMID:23613840

Nutritional Evaluation of Australian Microalgae as Potential Human Health Supplements

PubMed Central

Kent, Megan; Welladsen, Heather M.; Mangott, Arnold; Li, Yan

2015-01-01

This study investigated the biochemical suitability of Australian native microalgal species Scenedesmus sp., Nannochloropsis sp., Dunaliella sp., and a chlorophytic polyculture as nutritional supplements for human health. The four microalgal cultures were harvested during exponential growth, lyophilized, and analysed for proximate composition (moisture, ash, lipid, carbohydrates, and protein), pigments, and amino acid and fatty acid profiles. The resulting nutritional value, based on biochemical composition, was compared to commercial Spirulina and Chlorella products. The Australian native microalgae exhibited similar, and in several cases superior, organic nutritional properties relative to the assessed commercial products, with biochemical profiles rich in high-quality protein, nutritious polyunsaturated fats (such as α-linolenic acid, arachidonic acid, and eicosapentaenoic acid), and antioxidant pigments. These findings indicate that the microalgae assessed have great potential as multi-nutrient human health supplements. PMID:25723496

The environmental sustainability of microalgae as feed for aquaculture: a life cycle perspective.

PubMed

Taelman, S E; De Meester, S; Roef, L; Michiels, M; Dewulf, J

2013-12-01

The environmental sustainability of microalgae production for aquaculture purposes was analyzed using exergy analysis (EA) and life cycle assessment (LCA). A production process (pilot 2012, 240 m(2)) was assessed and compared with two upscaling scenarios (pilot 2013, 1320 m(2) and first production scale 2015, 2.5 ha). The EA at process level revealed that drying and cultivation had the lowest efficiencies. The LCA showed an improvement in resource efficiency after upscaling: 55.5 MJ(ex,CEENE)/MJ(ex) DW biomass was extracted from nature in 2012, which was reduced to 21.6 and 2.46 MJ(ex,CEENE)/MJ(ex) DW in the hypothetical 2013 and 2015 scenarios, respectively. Upscaling caused the carbon footprint to decline by factor 20 (0.09 kg CO2,eq/MJ(ex) DW in 2015). In the upscaling scenarios, microalgae production for aquaculture purposes appeared to be more sustainable in resource use than a reference fish feed (7.70 MJ(ex,CEENE) and 0.05 kg CO2,eq per MJ(ex) DW). Copyright © 2013 Elsevier Ltd. All rights reserved.

Inhibitory effects of soluble algae products (SAP) released by Scenedesmus sp. LX1 on its growth and lipid production.

PubMed

Zhang, Tian-Yuan; Yu, Yin; Wu, Yin-Hu; Hu, Hong-Ying

2013-10-01

Soluble algal products (SAP) accumulated in culture medium via water reuse may affect the growth of microalga during the cultivation. Scenedesmus sp. LX1, a freshwater microalga, was used in this study to investigate the effect of SAP on growth and lipid production of microalga. Under the SAP concentrations of 6.4-25.8 mg L(-1), maximum algal density (K) and maximum growth rate (Rmax) of Scenedesmus sp. LX1 were decreased by 50-80% and 35-70% compared with the control group, respectively. The effect of SAP on lipid accumulation of Scenedesmus sp. LX1 was non-significant. According to hydrophilic-hydrophobic and acid-base properties, SAP was fractionized into six fractions. All of the fractions could inhibit the growth of Scenedesmus sp. LX1. Organic bases (HIB, HOB) and hydrophilic acids (HIA) showed the strongest inhibition. HIA could also decrease the lipid content of Scenedesmus sp. LX1 by 59.2%. As the inhibitory effect, SAP should be seriously treated before water reuse. Copyright © 2013 Elsevier Ltd. All rights reserved.

Identification of carbohydrates as the major carbon sink of the marine microalga Isochrysis zhangjiangensis (Haptophyta) and optimization of its productivity by nitrogen manipulation.

PubMed

Wang, Hai-Tao; Yao, Chang-Hong; Ai, Jiang-Ning; Cao, Xu-Peng; Xue, Song; Wang, Wei-liang

2014-11-01

Microalgae represent a potential feedstock for biofuel production. During cultivation under nitrogen-depleted conditions, carbohydrates, rather than neutral lipids, were the major carbon sink of the marine microalga Isochrysis zhangjiangensis (Haptophyta). Carbohydrates reached maximum levels of 21.2 pg cell(-1) on day 5, which was an increase of more than 7-fold from day 1, while neutral lipids simultaneously increased 1.9-fold from 4.0 to 7.6 pg cell(-1) during the ten-day nitrogen-depleted cultivation. The carbohydrate productivity of I. zhangjiangensis was improved by optimization of the nitrate supply mode. The maximum carbohydrate concentration was 0.95 g L(-1) under batch cultivation, with an initial nitrogen concentration of 31.0 mg L(-1), which was 2.4-fold greater than that achieved under nitrogen-depleted conditions. High performance liquid chromatography (HPLC) analysis showed that the accumulated carbohydrate in I. zhangjiangensis was composed of glucose. These results show that I. zhangjiangensis represents an ideal carbohydrate-enriched bioresource for biofuel production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Lipid extraction methods from microalgal biomass harvested by two different paths: screening studies toward biodiesel production.

PubMed

Ríos, Sergio D; Castañeda, Joandiet; Torras, Carles; Farriol, Xavier; Salvadó, Joan

2013-04-01

Microalgae can grow rapidly and capture CO2 from the atmosphere to convert it into complex organic molecules such as lipids (biodiesel feedstock). High scale economically feasible microalgae based oil depends on optimizing the entire process production. This process can be divided in three very different but directly related steps (production, concentration, lipid extraction and transesterification). The aim of this study is to identify the best method of lipid extraction to undergo the potentiality of some microalgal biomass obtained from two different harvesting paths. The first path used all physicals concentration steps, and the second path was a combination of chemical and physical concentration steps. Three microalgae species were tested: Phaeodactylum tricornutum, Nannochloropsis gaditana, and Chaetoceros calcitrans One step lipid extraction-transesterification reached the same fatty acid methyl ester yield as the Bligh and Dyer and soxhlet extraction with n-hexane methods with the corresponding time, cost and solvent saving. Copyright © 2013 Elsevier Ltd. All rights reserved.

Concurrent production of biodiesel and chemicals through wet in situ transesterification of microalgae.

PubMed

Im, Hanjin; Kim, Bora; Lee, Jae W

2015-10-01

This work addresses an unprecedented way of co-producing biodiesel (FAEE) and valuable chemicals of ethyl levulinate (EL), ethyl formate (EF) and diethyl ether (DEE) from wet in situ transesterification of microalgae. EL, EF, and DEE were significantly produced up to 23.1%, 10.3%, and 52.1% of the maximum FAEE mass with the FAEE yield higher than 90% at 125 °C. Experiments to elucidate a detailed route of EL and EF synthesis were fulfilled and it was found that its main route to the production of EL and EF was the acid hydrolysis of algal cells and esterification with ethanol. To investigate the effect of reaction variables on the products yields, comprehensive experiments were carried out with varying temperatures, solvent and alcohol volumes, moisture contents and catalyst amounts. Coproduction of DEE, EL, EF and FAEE can contribute to elevating the economic feasibility of microalgae-based biodiesel supply chain. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biochemical compositions and fatty acid profiles in four species of microalgae cultivated on household sewage and agro-industrial residues.

PubMed

Calixto, Clediana Dantas; da Silva Santana, Jordana Kaline; de Lira, Evandro Bernardo; Sassi, Patrícia Giulianna Petraglia; Rosenhaim, Raul; da Costa Sassi, Cristiane Francisca; da Conceição, Marta Maria; Sassi, Roberto

2016-12-01

The potential of four regional microalgae species was evaluated in relation to their cell growth and biomass production when cultured in the following alternative media: bio-composts of fruit/horticultural wastes (HB), sugarcane waste and vinasse (VB) chicken excrements (BCE), raw chicken manure (RCM), and municipal domestic sewage (MDS). The cultures were maintained under controlled conditions and their growth responses, productivities, biochemical compositions, and the ester profiles of their biomasses were compared to the results obtained in the synthetic media. The MDS and HB media demonstrated promising results for cultivation, especially of Chlorella sp., Chlamydomonas sp., and Lagerheimia longiseta, which demonstrated productivities superior to those seen when grown on the control media. The highest lipid levels were obtained with the HB medium. The data obtained demonstrated the viability of cultivating microalgae and producing biomass in alternative media prepared from MDS and HB effluents to produce biodiesel. Copyright © 2016 Elsevier Ltd. All rights reserved.

Preliminary Study on the Location Selection of Microalgae Cultivation In Nusa Tenggara Region As A Potential Feedstock For Bioavtur

NASA Astrophysics Data System (ADS)

Anggraini, Citrae Permata Kusuma; Sasongko, Nugroho Adi; Kuntjoro, Yanif Dwi

2018-02-01

NTT is a province located in strategic areas between Bali and South Sulawesi which has economic growth 5,08% in 2016. This causes air transportation in NTT to grow rapidly so the need for avtur is increased by 6% per year. To meet the needs of avtur in NTT would require energy diversification with bioavtur development in which one of them comes from microalgae. The content of lipid and hydrocarbon in microalgae can be used as a source of bioavtur feedstock. The suitability of location for cultivation will influence the success of microalgae cultivation that will be used as a source of bioavtur feedstock. The purpose of this research is to choose the best location for microalgae cultivation in NTT by AHP method. The criteria used in this research are nutrient, water and technology. Sub criteria of nutrient elements are coal power plant emission, cement industry emission and synthetic fertilizers, sub criteria from water that is sea water, brackish water and fresh water, while sub criteria of technology are Photobioreactor, Open Raceway Pond and membrane. The result of AHP analysis shows the selection of microalgae cultivation location in Kupang with the weight of 0.308, with the source of nutrient derived from coal power plant emission, the type of water used is sea water and the technology used is Photobioreactor. Microalgae species used were Nannochloropsis sp with a lipid content of 31-68%. Based on the author assumption, microalgae have the productivity for bioavtur manufacture which amount of 24.489kL/ha/ yr. That can be used to meet the needs of 2% avtur in NTT which amount of 1.052,22 kL/yr and the area requirement for microalgae cultivation is 2,14 hectare.

An Integrated Assessment of Location-Dependent Scaling for Microalgae Biofuel Production Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coleman, Andre M.; Abodeely, Jared; Skaggs, Richard

Successful development of a large-scale microalgae-based biofuels industry requires comprehensive analysis and understanding of the feedstock supply chain—from facility siting/design through processing/upgrading of the feedstock to a fuel product. The evolution from pilot-scale production facilities to energy-scale operations presents many multi-disciplinary challenges, including a sustainable supply of water and nutrients, operational and infrastructure logistics, and economic competitiveness with petroleum-based fuels. These challenges are addressed in part by applying the Integrated Assessment Framework (IAF)—an integrated multi-scale modeling, analysis, and data management suite—to address key issues in developing and operating an open-pond facility by analyzing how variability and uncertainty in space andmore » time affect algal feedstock production rates, and determining the site-specific “optimum” facility scale to minimize capital and operational expenses. This approach explicitly and systematically assesses the interdependence of biofuel production potential, associated resource requirements, and production system design trade-offs. The IAF was applied to a set of sites previously identified as having the potential to cumulatively produce 5 billion-gallons/year in the southeastern U.S. and results indicate costs can be reduced by selecting the most effective processing technology pathway and scaling downstream processing capabilities to fit site-specific growing conditions, available resources, and algal strains.« less

Genome and methylome of the oleaginous diatom Cyclotella cryptica reveal genetic flexibility toward a high lipid phenotype

DOE Office of Scientific and Technical Information (OSTI.GOV)

Traller, Jesse C.; Cokus, Shawn J.; Lopez, David A.

Here, improvement in the performance of eukaryotic microalgae for biofuel and bioproduct production is largely dependent on characterization of metabolic mechanisms within the cell. The marine diatom Cyclotella cryptica, which was originally identified in the Aquatic Species Program, is a promising strain of microalgae for large-scale production of biofuel and bioproducts, such as omega-3 fatty acids. As a result, we sequenced the nuclear genome and methylome of this oleaginous diatom to identify the genetic traits that enable substantial accumulation of triacylglycerol. The genome is comprised of highly methylated repetitive sequence, which does not significantly change under silicon starved lipid induction,more » and data further suggests the primary role of DNA methylation is to suppress DNA transposition. Annotation of pivotal glycolytic, lipid metabolism, and carbohydrate degradation processes reveal an expanded enzyme repertoire in C. cryptica that would allow for an increased metabolic capacity toward triacylglycerol production. Identification of previously unidentified genes, including those involved in carbon transport and chitin metabolism, provide potential targets for genetic manipulation of carbon flux to further increase its lipid phenotype. New genetic tools were developed, bringing this organism on a par with other microalgae in terms of genetic manipulation and characterization approaches. Furthermore, functional annotation and detailed cross-species comparison of key carbon rich processes in C. cryptica highlights the importance of enzymatic subcellular compartmentation for regulation of carbon flux, which is often overlooked in photosynthetic microeukaryotes. The availability of the genome sequence, as well as advanced genetic manipulation tools enable further development of this organism for deployment in large-scale production systems.« less

Genome and methylome of the oleaginous diatom Cyclotella cryptica reveal genetic flexibility toward a high lipid phenotype

DOE PAGES

Traller, Jesse C.; Cokus, Shawn J.; Lopez, David A.; ...

2016-11-25

Here, improvement in the performance of eukaryotic microalgae for biofuel and bioproduct production is largely dependent on characterization of metabolic mechanisms within the cell. The marine diatom Cyclotella cryptica, which was originally identified in the Aquatic Species Program, is a promising strain of microalgae for large-scale production of biofuel and bioproducts, such as omega-3 fatty acids. As a result, we sequenced the nuclear genome and methylome of this oleaginous diatom to identify the genetic traits that enable substantial accumulation of triacylglycerol. The genome is comprised of highly methylated repetitive sequence, which does not significantly change under silicon starved lipid induction,more » and data further suggests the primary role of DNA methylation is to suppress DNA transposition. Annotation of pivotal glycolytic, lipid metabolism, and carbohydrate degradation processes reveal an expanded enzyme repertoire in C. cryptica that would allow for an increased metabolic capacity toward triacylglycerol production. Identification of previously unidentified genes, including those involved in carbon transport and chitin metabolism, provide potential targets for genetic manipulation of carbon flux to further increase its lipid phenotype. New genetic tools were developed, bringing this organism on a par with other microalgae in terms of genetic manipulation and characterization approaches. Furthermore, functional annotation and detailed cross-species comparison of key carbon rich processes in C. cryptica highlights the importance of enzymatic subcellular compartmentation for regulation of carbon flux, which is often overlooked in photosynthetic microeukaryotes. The availability of the genome sequence, as well as advanced genetic manipulation tools enable further development of this organism for deployment in large-scale production systems.« less

Magnetic-Nanoflocculant-Assisted Water-Nonpolar Solvent Interface Sieve for Microalgae Harvesting.

PubMed

Lee, Kyubock; Na, Jeong-Geol; Seo, Jung Yoon; Shim, Tae Soup; Kim, Bohwa; Praveenkumar, Ramasamy; Park, Ji-Yeon; Oh, You-Kwan; Jeon, Sang Goo

2015-08-26

Exploitation of magnetic flocculants is regarded as a very promising energy-saving approach to microalgae harvesting. However, its practical applicability remains limited, mainly because of the problem of the postharvest separation of magnetic flocculants from microalgal flocs, which is crucial both for magnetic-flocculant recycling and high-purity microalgal biomasses, but which is also a very challenging and energy-consuming step. In the present study, we designed magnetic nanoflocculants dually functionalizable by two different organosilane compounds, (3-aminopropyl)triethoxysilane (APTES) and octyltriethoxysilane (OTES), which flocculate negatively charged microalgae and are readily detachable at the water-nonpolar organic solvent (NOS) interface only by application of an external magnetic field. APTES functionalization imparts a positive zeta potential charge (29.6 mV) to magnetic nanoflocculants, thereby enabling microalgae flocculation with 98.5% harvesting efficiency (with a dosage of 1.6 g of dMNF/g of cells). OTES functionalization imparts lipophilicity to magnetic nanoflocculants to make them compatible with NOS, thus effecting efficient separation of magnetic flocculants passing through the water-NOS interface sieve from hydrophilic microalgae. Our new energy-saving approach to microalgae harvesting concentrates microalgal cultures (∼1.5 g/L) up to 60 g/L, which can be directly connected to the following process of NOS-assisted wet lipid extraction or biodiesel production, and therefore provides, by simplifying multiple downstream processes, a great potential cost reduction in microalgae-based biorefinement.

Evaluation of High Rate Algae Ponds for treatment of anaerobically digested wastewater: Effect of CO2 addition and modification of dilution rate.

PubMed

de Godos, I; Arbib, Z; Lara, E; Rogalla, F

2016-11-01

High Rate Algae Ponds (HRAP) are the simplest way to grow microalgae biomass and an interesting alternative for wastewater treatment. In this work the performance of these systems was evaluated using anaerobically digested wastewater as culture medium. Two variables were studied in long-term mode: the carbon dioxide supply and the modification of the dilution rates. The results showed that CO2 supply increases the productivity but less than expected considering the potential biomass generation calculated based on the ratios of carbon to nitrogen of microalgae and wastewater. The assimilation into biomass only accounted for 57% of the inlet nitrogen under the best conditions because nitrification and volatilization reduced the availability of this element. The operation under short hydraulic retention times presented a more interesting performance with higher biomass productivities. The biomass produced was efficiently harvested with in a Dissolved Air Flotation (DAF) unit. Copyright © 2016 Elsevier Ltd. All rights reserved.

Commercial development of microalgal biotechnology: from the test tube to the marketplace.

PubMed

Olaizola, Miguel

2003-07-01

While humans have taken limited advantage of natural populations of microalgae for centuries (Nostoc in Asia and Spirulina in Africa and North America for sustenance), it is only recently that we have come to realize the potential of microalgal biotechnology. Microalgal biotechnology has the potential to produce a vast array of products including foodstuffs, industrial chemicals, compounds with therapeutic applications and bioremediation solutions from a virtually untapped source. From an industrial (i.e. commercial) perspective, the goal of microalgal biotechnology is to make money by developing marketable products. For such a business to succeed the following steps must be taken: identify a desirable metabolite and a microalga that produces and accumulates the desired metabolite, establish a large-scale production process for the desired metabolite, and market the desired metabolite. So far, the commercial achievements of microalgal biotechnology have been modest. Microalgae that produce dozens of desirable metabolites have been identified. Aided by high throughput screening technology even more leads will become available. However, the successes in large-scale production and product marketing have been few. We will discuss those achievements and difficulties from the industrial point of view by considering examples from industry, specially our own experience at Mera Pharmaceuticals.

A Review of Enzymatic Transesterification of Microalgal Oil-Based Biodiesel Using Supercritical Technology

PubMed Central

Taher, Hanifa; Al-Zuhair, Sulaiman; Al-Marzouqi, Ali H.; Haik, Yousef; Farid, Mohammed M.

2011-01-01

Biodiesel is considered a promising replacement to petroleum-derived diesel. Using oils extracted from agricultural crops competes with their use as food and cannot realistically satisfy the global demand of diesel-fuel requirements. On the other hand, microalgae, which have a much higher oil yield per hectare, compared to oil crops, appear to be a source that has the potential to completely replace fossil diesel. Microalgae oil extraction is a major step in the overall biodiesel production process. Recently, supercritical carbon dioxide (SC-CO2) has been proposed to replace conventional solvent extraction techniques because it is nontoxic, nonhazardous, chemically stable, and inexpensive. It uses environmentally acceptable solvent, which can easily be separated from the products. In addition, the use of SC-CO2 as a reaction media has also been proposed to eliminate the inhibition limitations that encounter biodiesel production reaction using immobilized enzyme as a catalyst. Furthermore, using SC-CO2 allows easy separation of the product. In this paper, conventional biodiesel production with first generation feedstock, using chemical catalysts and solvent-extraction, is compared to new technologies with an emphasis on using microalgae, immobilized lipase, and SC-CO2 as an extraction solvent and reaction media. PMID:21915372

A Holistic Approach to Managing Microalgae for Biofuel Applications

PubMed Central

Show, Pau Loke; Tang, Malcolm S. Y.; Nagarajan, Dillirani; Ling, Tau Chuan; Ooi, Chien-Wei; Chang, Jo-Shu

2017-01-01

Microalgae contribute up to 60% of the oxygen content in the Earth’s atmosphere by absorbing carbon dioxide and releasing oxygen during photosynthesis. Microalgae are abundantly available in the natural environment, thanks to their ability to survive and grow rapidly under harsh and inhospitable conditions. Microalgal cultivation is environmentally friendly because the microalgal biomass can be utilized for the productions of biofuels, food and feed supplements, pharmaceuticals, nutraceuticals, and cosmetics. The cultivation of microalgal also can complement approaches like carbon dioxide sequestration and bioremediation of wastewaters, thereby addressing the serious environmental concerns. This review focuses on the factors affecting microalgal cultures, techniques adapted to obtain high-density microalgal cultures in photobioreactors, and the conversion of microalgal biomass into biofuels. The applications of microalgae in carbon dioxide sequestration and phycoremediation of wastewater are also discussed. PMID:28117737

Microalgae harvesting techniques: A review.

PubMed

Singh, Gulab; Patidar, S K

2018-07-01

Microalgae with wide range of commercial applications have attracted a lot of attention of the researchers in the last few decades. However, microalgae utilization is not economically sustainable due to high cost of harvesting. A wide range of solid - liquid separation techniques are available for microalgae harvesting. The techniques include coagulation and flocculation, flotation, centrifugation and filtration or a combination of various techniques. Despite the importance of harvesting to the economics and energy balance, there is no universal harvesting technique for microalgae. Therefore, this review focuses on assessing technical, economical and application potential of various harvesting techniques so as to allow selection of an appropriate technology for cost effectively harvesting of microalgae from their culture medium. Various harvesting and concentrating techniques of microalgae were reviewed to suggest order of suitability of the techniques for four main microalgae applications i.e biofuel, human and animal food, high valued products, and water quality restoration. For deciding the order of suitability, a comparative analysis of various harvesting techniques based on the six common criterions (i.e biomass quality, cost, biomass quantity, processing time, species specific and toxicity) has been done. Based on the order of various techniques vis-a-vis various criteria and preferred order of criteria for various applications, order of suitability of harvesting techniques for various applications has been decided. Among various harvesting techniques, coagulation and flocculation, centrifugation and filtration were found to be most suitable for considered applications. These techniques may be used alone or in combination for increasing the harvesting efficiency. Copyright © 2018 Elsevier Ltd. All rights reserved.

Multi-Wavelength Based Optical Density Sensor for Autonomous Monitoring of Microalgae

PubMed Central

Jia, Fei; Kacira, Murat; Ogden, Kimberly L.

2015-01-01

A multi-wavelength based optical density sensor unit was designed, developed, and evaluated to monitor microalgae growth in real time. The system consisted of five main components including: (1) laser diode modules as light sources; (2) photodiodes as detectors; (3) driver circuit; (4) flow cell; and (5) sensor housing temperature controller. The sensor unit was designed to be integrated into any microalgae culture system for both real time and non-real time optical density measurements and algae growth monitoring applications. It was shown that the sensor unit was capable of monitoring the dynamics and physiological changes of the microalgae culture in real-time. Algae biomass concentration was accurately estimated with optical density measurements at 650, 685 and 780 nm wavelengths used by the sensor unit. The sensor unit was able to monitor cell concentration as high as 1.05 g·L−1 (1.51 × 108 cells·mL−1) during the culture growth without any sample preparation for the measurements. Since high cell concentrations do not need to be diluted using the sensor unit, the system has the potential to be used in industrial microalgae cultivation systems for real time monitoring and control applications that can lead to improved resource use efficiency. PMID:26364640

Establishment of an efficient genetic transformation method in Dunaliella tertiolecta mediated by Agrobacterium tumefaciens.

PubMed

Norzagaray-Valenzuela, Claudia D; Germán-Báez, Lourdes J; Valdez-Flores, Marco A; Hernández-Verdugo, Sergio; Shelton, Luke M; Valdez-Ortiz, Angel

2018-05-16

Microalgae are photosynthetic microorganisms widely used for the production of highly valued compounds, and recently they have been shown to be promising as a system for the heterologous expression of proteins. Several transformation methods have been successfully developed, from which the Agrobacterium tumefaciens-mediated method remains the most promising. However, microalgae transformation efficiency by A. tumefaciens is shown to vary depending on several transformation conditions. The present study aimed to establish an efficient genetic transformation system in the green microalgae Dunaliella tertiolecta using the A. tumefaciens method. The parameters assessed were the infection medium, the concentration of the A. tumefaciens and co-culture time. As a preliminary screening, the expression of the gusA gene and the viability of transformed cells were evaluated and used to calculate a novel parameter called Transformation Efficiency Index (TEI). The statistical analysis of TEI values showed five treatments with the highest gusA gene expression. To ensure stable transformation, transformed colonies were cultured on selective medium using hygromycin B and the DNA of resistant colonies were extracted after five subcultures and molecularly analyzed by PCR. Results revealed that treatments which use solid infection medium, A. tumefaciens OD 600  = 0.5 and co-culture times of 72 h exhibited the highest percentage of stable gusA expression. Overall, this study established an efficient, optimized A. tumefaciens-mediated genetic transformation of D. tertiolecta, which represents a relatively easy procedure with no expensive equipment required. This simple and efficient protocol opens the possibility for further genetic manipulation of this commercially-important microalgae for biotechnological applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Growth and biomass productivity of Scenedesmus vacuolatus on a twin layer system and a comparison with other types of cultivations.

PubMed

Carbone, Dora Allegra; Olivieri, Giuseppe; Pollio, Antonino; Gabriele; Melkonian, Michael

2017-12-01

Scenedesmus is a genus of microalgae employed for several industrial uses. Industrial cultivations are performed in open ponds or in closed photobioreactors (PBRs). In the last years, a novel type of PBR based on immobilized microalgae has been developed termed porous substrate photobioreactors (PSBR) to achieve significant higher biomass density during cultivation in comparison to classical PBRs. This work presents a study of the growth of Scenedesmus vacuolatus in a Twin Layer System PSBR at different light intensities (600 μmol photons m -2  s -1 or 1000 μmol photons m -2  s -1 ), different types and concentrations of the nitrogen sources (nitrate or urea), and at two CO 2 levels in the gas phase (2% or 0.04% v/v). The microalgal growth was followed by monitoring the attached biomass density as dry weight, the specific growth rate and pigment accumulation. The highest productivity (29 g m -2 d -1 ) was observed at a light intensity of 600 μmol photons m -2  s -1 and 2% CO 2 . The types and concentrations of nitrogen sources did not influence the biomass productivity. Instead, the higher light intensity of 1000 μmol photons m -2  s -1 and an ambient CO 2 concentration (0.04%) resulted in a significant decrease of productivity to 18 and 10-12 g m -2 d -1 , respectively. When compared to the performance of similar cultivation systems (15-30 g m -2 d -1 ), these results indicate that the Twin Layer cultivation System is a competitive technique for intensified microalgal cultivation in terms of productivity and, at the same time, biomass density.

Polishing of municipal secondary effluent using native microalgae consortia.

PubMed

Beltrán-Rocha, Julio César; Barceló-Quintal, Icela Dagmar; García-Martínez, Magdalena; Osornio-Berthet, Luis; Saavedra-Villarreal, Nidia; Villarreal-Chiu, Juan; López-Chuken, Ulrico Javier

2017-04-01

This work evaluates the use of native microalgae consortia for a dual role: polishing treatment of municipal wastewater effluents and microalgae biomass feedstock potential for biodiesel or biofertilizer production. An initial screening was undertaken to test N and P removal from secondary effluents and biomass production by 12 consortia. A subsequent treatment was performed by selected consortia (01 and 12) under three operational conditions: stirring (S), S + 12 h of daily aeration (S + A) and S + A enriched with CO 2 (S + AC). All treatments resulted in compliance with environmental regulations (e.g. Directive 91/271/EEC) and high removal efficiency of nutrients: 64-79% and 80-94% of total N and PO 4 3- -P respectively. During the experiments it was shown that pH alkalinization due to microalgae growth benefits the chemical removal of ammonia and phosphorus. Moreover, advantages of pH increase could be accomplished by intermittent CO 2 addition which in this research (treatment S + AC) promoted higher yield and lipid concentration. The resulting dry biomass analysis showed a low lipid content (0.5-4.3%) not ideal for biodiesel production. Moreover, the high rate of ash (29.3-53.0%) suggests that biomass could be readily recycled as a biofertilizer due to mineral supply and organic constituents formed by C, N and P (e.g. carbohydrate, protein, and lipids).

Association with an Ammonium-Excreting Bacterium Allows Diazotrophic Culture of Oil-Rich Eukaryotic Microalgae

PubMed Central

Ortiz-Marquez, Juan Cesar Federico; Do Nascimento, Mauro; Dublan, Maria de los Angeles

2012-01-01

Concerns regarding the depletion of the world's reserves of oil and global climate change have promoted an intensification of research and development toward the production of biofuels and other alternative sources of energy during the last years. There is currently much interest in developing the technology for third-generation biofuels from microalgal biomass mainly because of its potential for high yields and reduced land use changes in comparison with biofuels derived from plant feedstocks. Regardless of the nature of the feedstock, the use of fertilizers, especially nitrogen, entails a potential economic and environmental drawback for the sustainability of biofuel production. In this work, we have studied the possibility of nitrogen biofertilization by diazotrophic bacteria applied to cultured microalgae as a promising feedstock for next-generation biofuels. We have obtained an Azotobacter vinelandii mutant strain that accumulates several times more ammonium in culture medium than wild-type cells. The ammonium excreted by the mutant cells is bioavailable to promote the growth of nondiazotrophic microalgae. Moreover, this synthetic symbiosis was able to produce an oil-rich microalgal biomass using both carbon and nitrogen from the air. This work provides a proof of concept that artificial symbiosis may be considered an alternative strategy for the low-N-intensive cultivation of microalgae for the sustainable production of next-generation biofuels and other bioproducts. PMID:22267660

Evaluation of Culture Conditions to Obtain Fatty Acids from Saline Microalgae Species: Dunaliella salina, Sinecosyfis sp., and Chroomonas sp.

PubMed Central

Castilla Casadiego, D. A.; Albis Arrieta, A. R.; Angulo Mercado, E. R.; Cervera Cahuana, S. J.; Baquero Noriega, K. S.; Suárez Escobar, A. F.; Morales Avendaño, E. D.

2016-01-01

The use of the saline microalgae, Dunaliella salina, Sinecosyfis sp., and Chroomonas sp., was explored as an alternative source for the production of fatty acids using fertilizer and glycerol as culture media. The nutrient medium used contained “Nutrifoliar,” a commercial fertilizer, and/or glycerol, in natural sea water. The microalgae were placed in cultures with different conditions. The parameters that favored the largest production of fatty acids were 24 hours of agitation and illumination, 1620 L/day of air supply, 2.25 L of air/min, and a temperature of 32°C using “Nutrifoliar” as the culture media. Results indicated that, from 3 g of microalgae in wet base of Chroomonas sp., 54.43 mg of oil was produced. The chromatographic characterization of oil obtained revealed the presence of essential fatty acids such as 9,12,15-octadecatrienoic acid (omega-3) and 4,7,10-hexadecatrienoic acid (omega-6) from the species Dunaliella salina. On the other hand, 9,12-octadecadienoic acid (omega-6) and cis-11-eicosenoic acid (omega-9) were identified from the species Chroomonas sp. The temperature variations played an important role in the velocity of growth or the production of the algae biomass, the amount of oil, and the ability to produce fatty acids. PMID:27376085

Enhancement of fermentative hydrogen production from Spirogyra sp. by increased carbohydrate accumulation and selection of the biomass pretreatment under a biorefinery model.

PubMed

Pinto, Tiago; Gouveia, Luísa; Ortigueira, Joana; Saratale, Ganesh D; Moura, Patrícia

2018-03-23

In this work, hydrogen (H 2 ) was produced through the fermentation of Spirogyra sp. biomass by Clostridium butyricum DSM 10702. Macronutrient stress was applied to increase the carbohydrate content in Spirogyra, and a 36% (w/w) accumulation of carbohydrates was reached by nitrogen depletion. The use of wet microalga as fermentable substrate was compared with physically and chemically treated biomass for increased carbohydrate solubilisation. The combination of drying, bead beating and mild acid hydrolysis produced a saccharification yield of 90.3% (w/w). The H 2 production from Spirogyra hydrolysate was 3.9 L H 2  L -1 , equivalent to 146.3 mL H 2  g -1 microalga dry weight. The presence of protein (23.2 ± 0.3% w/w) and valuable pigments, such as astaxanthin (38.8% of the total pigment content), makes this microalga suitable to be used simultaneously in both food and feed applications. In a Spirogyra based biorefinery, the potential energy production and food-grade protein and pigments revenue per cubic meter of microalga culture per year was estimated on 7.4 MJ, US $412 and US $15, respectively, thereby contributing to the cost efficiency and sustainability of the whole bioconversion process. Copyright © 2018 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Algal biofuels.

PubMed

Razeghifard, Reza

2013-11-01

The world is facing energy crisis and environmental issues due to the depletion of fossil fuels and increasing CO2 concentration in the atmosphere. Growing microalgae can contribute to practical solutions for these global problems because they can harvest solar energy and capture CO2 by converting it into biofuel using photosynthesis. Microalgae are robust organisms capable of rapid growth under a variety of conditions including in open ponds or closed photobioreactors. Their reduced biomass compounds can be used as the feedstock for mass production of a variety of biofuels. As another advantage, their ability to accumulate or secrete biofuels can be controlled by changing their growth conditions or metabolic engineering. This review is aimed to highlight different forms of biofuels produced by microalgae and the approaches taken to improve their biofuel productivity. The costs for industrial-scale production of algal biofuels in open ponds or closed photobioreactors are analyzed. Different strategies for photoproduction of hydrogen by the hydrogenase enzyme of green algae are discussed. Algae are also good sources of biodiesel since some species can make large quantities of lipids as their biomass. The lipid contents for some of the best oil-producing strains of algae in optimized growth conditions are reviewed. The potential of microalgae for producing petroleum related chemicals or ready-make fuels such as bioethanol, triterpenic hydrocarbons, isobutyraldehyde, isobutanol, and isoprene from their biomass are also presented.

Evaluation of Culture Conditions to Obtain Fatty Acids from Saline Microalgae Species: Dunaliella salina, Sinecosyfis sp., and Chroomonas sp.

PubMed

Castilla Casadiego, D A; Albis Arrieta, A R; Angulo Mercado, E R; Cervera Cahuana, S J; Baquero Noriega, K S; Suárez Escobar, A F; Morales Avendaño, E D

2016-01-01

The use of the saline microalgae, Dunaliella salina, Sinecosyfis sp., and Chroomonas sp., was explored as an alternative source for the production of fatty acids using fertilizer and glycerol as culture media. The nutrient medium used contained "Nutrifoliar," a commercial fertilizer, and/or glycerol, in natural sea water. The microalgae were placed in cultures with different conditions. The parameters that favored the largest production of fatty acids were 24 hours of agitation and illumination, 1620 L/day of air supply, 2.25 L of air/min, and a temperature of 32°C using "Nutrifoliar" as the culture media. Results indicated that, from 3 g of microalgae in wet base of Chroomonas sp., 54.43 mg of oil was produced. The chromatographic characterization of oil obtained revealed the presence of essential fatty acids such as 9,12,15-octadecatrienoic acid (omega-3) and 4,7,10-hexadecatrienoic acid (omega-6) from the species Dunaliella salina. On the other hand, 9,12-octadecadienoic acid (omega-6) and cis-11-eicosenoic acid (omega-9) were identified from the species Chroomonas sp. The temperature variations played an important role in the velocity of growth or the production of the algae biomass, the amount of oil, and the ability to produce fatty acids.

Association with an ammonium-excreting bacterium allows diazotrophic culture of oil-rich eukaryotic microalgae.

PubMed

Ortiz-Marquez, Juan Cesar Federico; Do Nascimento, Mauro; Dublan, Maria de Los Angeles; Curatti, Leonardo

2012-04-01

Concerns regarding the depletion of the world's reserves of oil and global climate change have promoted an intensification of research and development toward the production of biofuels and other alternative sources of energy during the last years. There is currently much interest in developing the technology for third-generation biofuels from microalgal biomass mainly because of its potential for high yields and reduced land use changes in comparison with biofuels derived from plant feedstocks. Regardless of the nature of the feedstock, the use of fertilizers, especially nitrogen, entails a potential economic and environmental drawback for the sustainability of biofuel production. In this work, we have studied the possibility of nitrogen biofertilization by diazotrophic bacteria applied to cultured microalgae as a promising feedstock for next-generation biofuels. We have obtained an Azotobacter vinelandii mutant strain that accumulates several times more ammonium in culture medium than wild-type cells. The ammonium excreted by the mutant cells is bioavailable to promote the growth of nondiazotrophic microalgae. Moreover, this synthetic symbiosis was able to produce an oil-rich microalgal biomass using both carbon and nitrogen from the air. This work provides a proof of concept that artificial symbiosis may be considered an alternative strategy for the low-N-intensive cultivation of microalgae for the sustainable production of next-generation biofuels and other bioproducts.

Carbon biofixation and lipid composition of an acidophilic microalga cultivated on treated wastewater supplied with different CO2 levels.

PubMed

Neves, Fábio de Farias; Hoinaski, Leonardo; Rörig, Leonardo Rubi; Derner, Roberto Bianchini; de Melo Lisboa, Henrique

2018-05-15

This study evaluated productivity, CO 2 biofixation, and lipid content in biomass of the acidophilic microalga Chlamydomonas acidophila LAFIC-004 cultivated with five different carbon dioxide concentrations. The influence of carbon dioxide concentration on nutrient removal and pH was also investigated. Treated wastewater (secondary effluent) was used as culture medium. Five experimental setups were tested: T-0% - injection of atmospheric air (0.038% CO 2 ), T-5% (5% CO 2 ), T-10% (10% CO 2 ), T-15% (15% CO 2 ) and T-20% (20% CO 2 ). The T-5% and T-10% experiments showed the highest values of productivity and CO 2 biofixation, and maximum biomass dry weight was 0.48 ± 0.02 and 0.51 ± 0.03 g L -1 , respectively. This acidophilic microalga proved to be suitable for carbon biofixation and removal of nutrients from secondary effluent of wastewater treatment plants with high CO 2 concentration. All assays were performed without pH control. This microalga species presented high lipid content. However, fatty acid methyl esters (FAME) are not suitable for biodiesel use.

Metabolites Re-programming and Physiological Changes Induced in Scenedesmus regularis under Nitrate Treatment.

PubMed

Ma, Nyuk-Ling; Aziz, Ahmad; Teh, Kit-Yinn; Lam, Su Shiung; Cha, Thye-San

2018-06-27

Nitrate is required to maintain the growth and metabolism of plant and animals. Nevertheless, in excess amount such as polluted water, its concentration can be harmful to living organisms such as microalgae. Recently, studies on microalgae response towards nutrient fluctuation are usually limited to lipid accumulation for the production of biofuels, disregarding the other potential of microalgae to be used in wastewater treatments and as source of important metabolites. Our study therefore captures the need to investigate overall metabolite changes via NMR spectroscopy approach coupled with multivariate data to understand the complex molecular process under high (4X) and low (1/4X) concentrations of nitrate ([Formula: see text]). NMR spectra with the aid of chemometric analysis revealed contrasting metabolites makeup under abundance and limited nitrate treatment. By using NMR technique, 43 types of metabolites and 8 types of fatty acid chains were detected. Nevertheless, only 20 key changes were observed and 16 were down regulated in limited nitrate condition. This paper has demonstrated the feasibility of NMR-based metabolomics approach to study the physiological impact of changing environment such as pollution to the implications for growth and productivity of microalgae population.

Low light intensity and nitrogen starvation modulate the chlorophyll content of Scenedesmus dimorphus.

PubMed

Ferreira, V S; Pinto, R F; Sant'Anna, C

2016-03-01

Chlorophyll is a photosynthetic pigment found in plants and algal organisms and is a bioproduct with human health benefits and a great potential for use in the food industry. The chlorophyll content in microalgae strains varies in response to environmental factors. In this work, we assessed the effect of nitrogen depletion and low light intensity on the chlorophyll content of the Scenedesmus dimorphus microalga. The growth of S. dimorphus under low light intensity led to a reduction in cell growth and volume as well as increased cellular chlorophyll content. Nitrogen starvation led to a reduction in cell growth and the chlorophyll content, changes in the yield and productivity of chlorophylls a and b. Transmission electron microscopy was used to investigate the ultrastructural changes in the S. dimorphus exposed to nitrogen and light deficiency. In contrast to nitrogen depletion, low light availability was an effective mean for increasing the total chlorophyll content of green microalga S. dimorphus. The findings acquired in this work are of great biotechnological importance to extend knowledge of choosing the right culture condition to stimulate the effectiveness of microalgae strains for chlorophyll production purposes. © 2015 The Society for Applied Microbiology.

Does zero-water discharged technology enhance culture performance of pacific white shrimp (Litopenaeus vannamei Boone.)?

NASA Astrophysics Data System (ADS)

Suantika, Gede; Anggraeni, Jayanty; Hasby, Fahri Azhari; Yanuwiarti, Ni Putu Indah

2014-03-01

Litopenaeus vannamei or white leg shrimp is an introduced shrimp which has successfully cultured in Indonesia. In Indonesia, L. vannamei is commonly cultured on outdoor/earthen pond that requires renewal of water, less control in term of water quality and disease and attributed to unpredictable yield production. Based on the existing culture condition, a system that enable to minimize water consumption, improve the hygiene of the culture and at the same time maintain a more stable yield production is urgent to be developed by using a zero water discharge system. The system consists of: (a) culture tank - to retain and culture the shrimp; (b) CaCO3 grained - buffering agent and substrate of nitrifying bacteria; (c) aeration line - to provide O2 and homogenize the culture; (d) ancho (feeding) - to control an appropriate feed; (e) nitrifying bacteria adding - to consume ammonium and nitrite then convert it to nitrate, and also control pathogen Vibrio sp.; (f) diatom microalgae (Chaetoceros gracilis) - to uptake nitrate, bacteriostatic agent, feed source, provide O2 and shading. In this study, there were 2 treatments: the static culture (batch) system was set as control (K) (in 70 PL/m2), and culture system with zero-water discharge system which was inoculated by 0.02% v/v 106 CFU/ml of mixed culture nitrifying bacteria and diatom microalgae in 70 PL/m2 (P1). The white leg shrimp used in this experiment was at post larvae (PL) 10 and cultured in a batch system (1 × 1 × 0.5 m3 pond) during 2 months. Several parameters including survival rate, mean body weight, and water quality (salinity, temperature, pH, DO, ammonium, nitrite, and nitrate) were measured. Based on the results, biomass of P1 (237.12 ± 31.11) gram is significantly higher than control (K) (180.80 ± 12.26) gram (P< 0,05). Water quality during the culture period in all treatments were still in tolerance range of white leg shrimp post larvae, except ammonium concentration in control (K) (2.612 ± 0.56) mg/L which is significantly different from P1 (1.287 ± 0.49) mg/L. Based on this research, zero-water discharge technology using nitrifying bacteria and diatom microalgae can improve productivity of white shrimp by increasing the biomass and maintaining a stable water quality especially ammonium concentration.

Biofuels from Microalgae and Seaweeds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huesemann, Michael H.; Roesijadi, Guritno; Benemann, John

2010-03-01

8.1 Introduction: Seaweeds and microalgae have a long history of cultivation as sources of commercial products (McHugh 2003; Pulz and Gross 2004). They also have been the subject of extensive investigations related to their potential as fuel source since the 1970s (Chynoweth 2002). As energy costs rise, these photosynthetic organisms are again a focus of interest as potential sources of biofuels, particularly liquid transportation fuels. There have been many recent private sector investments to develop biofuels from microalgae, in part building on a U.S. Department of Energy (DOE) program from 1976 to 1996 which focused on microalgal oil production (Sheehanmore » et al. 1998). Seaweed cultivation has received relatively little attention as a biofuel source in the US, but was the subject of a major research effort by the DOE from 1978 to 1983 (Bird and Benson 1987), and is now the focus of significant interest in Japan, Europe and Korea...« less

Non-conventional expression systems for the production of vaccine proteins and immunotherapeutic molecules

PubMed Central

Legastelois, Isabelle; Buffin, Sophie; Peubez, Isabelle; Mignon, Charlotte; Sodoyer, Régis; Werle, Bettina

2017-01-01

ABSTRACT The increasing demand for recombinant vaccine antigens or immunotherapeutic molecules calls into question the universality of current protein expression systems. Vaccine production can require relatively low amounts of expressed materials, but represents an extremely diverse category consisting of different target antigens with marked structural differences. In contrast, monoclonal antibodies, by definition share key molecular characteristics and require a production system capable of very large outputs, which drives the quest for highly efficient and cost-effective systems. In discussing expression systems, the primary assumption is that a universal production platform for vaccines and immunotherapeutics will unlikely exist. This review provides an overview of the evolution of traditional expression systems, including mammalian cells, yeast and E.coli, but also alternative systems such as other bacteria than E. coli, transgenic animals, insect cells, plants and microalgae, Tetrahymena thermophila, Leishmania tarentolae, filamentous fungi, cell free systems, and the incorporation of non-natural amino acids. PMID:27905833

The Challenge of Ecophysiological Biodiversity for Biotechnological Applications of Marine Microalgae

PubMed Central

Barra, Lucia; Chandrasekaran, Raghu; Corato, Federico; Brunet, Christophe

2014-01-01

In this review, we aim to explore the potential of microalgal biodiversity and ecology for biotechnological use. A deeper exploration of the biodiversity richness and ecophysiological properties of microalgae is crucial for enhancing their use for applicative purposes. After describing the actual biotechnological use of microalgae, we consider the multiple faces of taxonomical, morphological, functional and ecophysiological biodiversity of these organisms, and investigate how these properties could better serve the biotechnological field. Lastly, we propose new approaches to enhancing microalgal growth, photosynthesis, and synthesis of valuable products used in biotechnological fields, mainly focusing on culture conditions, especially light manipulations and genetic modifications. PMID:24663117

Biofuel production utilizing a dual-phase cultivation system with filamentous cyanobacteria.

PubMed

Aoki, Jinichi; Kawamata, Toru; Kodaka, Asuka; Minakawa, Masayuki; Imamura, Nobukazu; Tsuzuki, Mikio; Asayama, Munehiko

2018-04-17

Biomass yields and biofuel production were examined in a dual (solid and liquid)-phase cultivation system (DuPHA) with the unique filamentous cyanobacteria, Pseudanabaena sp. ABRG 5-3 and Limnothrix sp. SK1-2-1. Continuous circular cultivation was driven under the indoor closed (IC) or indoor opened (IO) conditions and provided biomass yields of approximately 8 to 27 g dry cell weight (DCW) floor m -2 d -1 . Alkanes of heptadecane (C 17 H 36 ) or pentadecane (C 15 H 32 ) as liquid biofuels were also recovered from the lower liquid-phase, in which cyanobacteria were dropped from the upper solid-phase and continuously cultivated with a small amount of medium. After the main cultivation in DuPHA, the upper solid-phase of a cotton cloth on which cyanobacteria grew was dried and directly subjected to a combustion test. This resulted in the thermal power (kJ s -1 ) of the cloth with microalgae increasing approximately 20 to 50% higher than that of the cloth only, suggesting a possibility of using the solid phase with microalgae as solid biofuel. Copyright © 2018. Published by Elsevier B.V.

Possible future effects of large-scale algae cultivation for biofuels on coastal eutrophication in Europe.

PubMed

Blaas, Harry; Kroeze, Carolien

2014-10-15

Biodiesel is increasingly considered as an alternative for fossil diesel. Biodiesel can be produced from rapeseed, palm, sunflower, soybean and algae. In this study, the consequences of large-scale production of biodiesel from micro-algae for eutrophication in four large European seas are analysed. To this end, scenarios for the year 2050 are analysed, assuming that in the 27 countries of the European Union fossil diesel will be replaced by biodiesel from algae. Estimates are made for the required fertiliser inputs to algae parks, and how this may increase concentrations of nitrogen and phosphorus in coastal waters, potentially leading to eutrophication. The Global NEWS (Nutrient Export from WaterSheds) model has been used to estimate the transport of nitrogen and phosphorus to the European coastal waters. The results indicate that the amount of nitrogen and phosphorus in the coastal waters may increase considerably in the future as a result of large-scale production of algae for the production of biodiesel, even in scenarios assuming effective waste water treatment and recycling of waste water in algae production. To ensure sustainable production of biodiesel from micro-algae, it is important to develop cultivation systems with low nutrient losses to the environment. Copyright © 2014 Elsevier B.V. All rights reserved.

Potential land competition between open-pond microalgae production and terrestrial dedicated feedstock supply systems in the U.S.

DOE PAGES

Coleman, Andre M.; Wigmosta, Mark S.; Hellwinckel, Chad M.; ...

2016-03-03

To date, feedstock resource assessments have evaluated cellulosic and algal feedstocks independently, without consideration of demands for, and resource allocation to, each other. We assess potential land competition between algal and terrestrial feedstocks in the United States, and evaluate a scenario in which 41.5 × 10 9 L yr –1 of second-generation biofuels are produced on pastureland, the most likely land base where both feedstock types may be deployed. Under this scenario, open-pond microalgae production is projected to use 1.2 × 10 6 ha of private pastureland, while terrestrial biomass feedstocks would use 14.0 × 10 6 ha of privatemore » pastureland. A spatial meta-analysis indicates that potential competition for land under this scenario would be concentrated in 110 counties, containing 1.0 and 1.7 × 10 6 ha of algal and terrestrial dedicated feedstock production, respectively. Furthermore, a land competition index applied to these 110 counties suggests that 38 to 59 counties could experience competition for upwards of 40% of a county's pastureland, representing 2%–5% of total pastureland in the U.S.; therefore suggesting little overall competition between algae production, terrestrial energy feedstocks and alternative uses for existing agricultural production such as livestock grazing.« less

Lipid catabolism in microalgae.

PubMed

Kong, Fantao; Romero, Ismael Torres; Warakanont, Jaruswan; Li-Beisson, Yonghua

2018-06-01

Lipid degradation processes are important in microalgae because survival and growth of microalgal cells under fluctuating environmental conditions require permanent remodeling or turnover of membrane lipids as well as rapid mobilization of storage lipids. Lipid catabolism comprises two major spatially and temporarily separated steps, namely lipolysis, which releases fatty acids and head groups and is catalyzed by lipases at membranes or lipid droplets, and degradation of fatty acids to acetyl-CoA, which occurs in peroxisomes through the β-oxidation pathway in green microalgae, and can sometimes occur in mitochondria in some other algal species. Here we review the current knowledge on the enzymes and regulatory proteins involved in lipolysis and peroxisomal β-oxidation and highlight gaps in our understanding of lipid degradation pathways in microalgae. Metabolic use of acetyl-CoA products via glyoxylate cycle and gluconeogenesis is also reviewed. We then present the implication of various cellular processes such as vesicle trafficking, cell cycle and autophagy on lipid turnover. Finally, physiological roles and the manipulation of lipid catabolism for biotechnological applications in microalgae are discussed. © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

A type 2 diacylglycerol acyltransferase accelerates the triacylglycerol biosynthesis in heterokont oleaginous microalga Nannochloropsis oceanica.

PubMed

Li, Da-Wei; Cen, Shi-Ying; Liu, Yu-Hong; Balamurugan, Srinivasan; Zheng, Xin-Yan; Alimujiang, Adili; Yang, Wei-Dong; Liu, Jie-Sheng; Li, Hong-Ye

2016-07-10

Oleaginous microalgae have received a considerable attention as potential biofuel feedstock. However, lack of industry-suitable strain with lipid rich biomass limits its commercial applications. Targeted engineering of lipogenic pathways represents a promising strategy to enhance the efficacy of microalgal oil production. In this study, a type 2 diacylglycerol acyltransferase (DGAT), a rate-limiting enzyme in triacylglycerol (TAG) biosynthesis, was identified and overexpressed in heterokont oleaginous microalga Nannochloropsis oceanica for the first time. Overexpression of DGAT2 in Nannochloropsis increased the relative transcript abundance by 3.48-fold in engineered microalgae cells. TAG biosynthesis was subsequently accelerated by DGAT2 overexpression and neutral lipid content was significantly elevated by 69% in engineered microalgae. The fatty acid profile determined by GC-MS revealed that fatty acid composition was altered in engineered microalgae. Saturated fatty acids and polyunsaturated fatty acids were found to be increased whereas monounsaturated fatty acids content decreased. Furthermore, DGAT2 overexpression did not show negative impact on algal growth parameters. The present investigation showed that the identified DGAT2 would be a potential candidate for enhancing TAG biosynthesis and might facilitate the development of promising oleaginous strains with industrial potential. Copyright © 2016 Elsevier B.V. All rights reserved.

Carotenoids from Marine Microalgae: A Valuable Natural Source for the Prevention of Chronic Diseases.

PubMed

Raposo, Maria Filomena de Jesus; de Morais, Alcina Maria Miranda Bernardo; de Morais, Rui Manuel Santos Costa

2015-08-14

Epidemiological studies have shown a relation between antioxidants and the prevention of several chronic diseases. Microalgae are a potential novel source of bioactive molecules, including a wide range of different carotenoids that can be used as nutraceuticals, food supplements and novel food products. The objective of this review is (i) to update the research that has been carried out on the most known carotenoids produced by marine microalgae, including reporting on their high potentialities to produce other less known important compounds; (ii) to compile the work that has been done in order to establish some relationship between carotenoids and oxidative protection and treatment; (iii) to summarize the association of oxidative stress and the various reactive species including free radicals with several human diseases; and (iv) to provide evidence of the potential of carotenoids from marine microalgae to be used as therapeutics to treat or prevent these oxidative stress-related diseases.

Carotenoids from Marine Microalgae: A Valuable Natural Source for the Prevention of Chronic Diseases

PubMed Central

Raposo, Maria Filomena de Jesus; de Morais, Alcina Maria Miranda Bernardo; de Morais, Rui Manuel Santos Costa

2015-01-01

Epidemiological studies have shown a relation between antioxidants and the prevention of several chronic diseases. Microalgae are a potential novel source of bioactive molecules, including a wide range of different carotenoids that can be used as nutraceuticals, food supplements and novel food products. The objective of this review is (i) to update the research that has been carried out on the most known carotenoids produced by marine microalgae, including reporting on their high potentialities to produce other less known important compounds; (ii) to compile the work that has been done in order to establish some relationship between carotenoids and oxidative protection and treatment; (iii) to summarize the association of oxidative stress and the various reactive species including free radicals with several human diseases; and (iv) to provide evidence of the potential of carotenoids from marine microalgae to be used as therapeutics to treat or prevent these oxidative stress-related diseases. PMID:26287216

The effect of growth phase on the surface properties of three oleaginous microalgae (Botryococcus sp. FACGB-762, Chlorella sp. XJ-445 and Desmodesmus bijugatus XJ-231)

PubMed Central

Xia, Ling; Huang, Rong; Li, Yinta

2017-01-01

The effects of growth phase on the lipid content and surface properties of oleaginous microalgae Botryococcus sp. FACGB-762, Chlorella sp. XJ-445 and Desmodesmus bijugatus XJ-231 were investigated in this study. The results showed that throughout the growth phases, the lipid content of microalgae increased. The surface properties like particle size, the degree of hydrophobicity, and the total concentration of functional groups increased while net surface zeta potential decreased. The results suggested that the growth stage had significant influence not only on the lipid content but also on the surface characteristics. Moreover, the lipid content was significantly positively related to the concentration of hydroxyl functional groups in spite of algal strains or growth phases. These results provided a basis for further studies on the refinery process using oleaginous microalgae for biofuel production. PMID:29045481

Microalgae-bacteria biofilms: a sustainable synergistic approach in remediation of acid mine drainage.

PubMed

Abinandan, Sudharsanam; Subashchandrabose, Suresh R; Venkateswarlu, Kadiyala; Megharaj, Mallavarapu

2018-02-01

Microalgae and bacteria offer a huge potential in delving interest to study and explore various mechanisms under extreme environments. Acid mine drainage (AMD) is one such environment which is extremely acidic containing copious amounts of heavy metals and poses a major threat to the ecosystem. Despite its extreme conditions, AMD is the habitat for several microbes and their activities. The use of various chemicals in prevention of AMD formation and conventional treatment in a larger scale is not feasible under different geological conditions. It implies that microbe-mediated approach is a viable and sustainable alternative technology for AMD remediation. Microalgae in biofilms play a pivotal role in such bioremediation as they maintain mutualism with heterotrophic bacteria. Synergistic approach of using microalgae-bacteria biofilms provides supportive metabolites from algal biomass for growth of bacteria and mediates remediation of AMD. However, by virtue of their physiology and capabilities of metal removal, non-acidophilic microalgae can be acclimated for use in AMD remediation. A combination of selective acidophilic and non-acidophilic microalgae together with bacteria, all in the form of biofilms, may be very effective for bioremediation of metal-contaminated waters. The present review critically examines the nature of mutualistic interactions established between microalgae and bacteria in biofilms and their role in removal of metals from AMDs, and consequent biomass production for the yield of biofuel. Integration of microalgal-bacterial consortia in fuel cells would be an attractive emerging approach of microbial biotechnology for AMD remediation.

Effect of gamma 60Co irradiation on the lipid content and fatty acid composition of Nannochloropsis sp. microalgae

NASA Astrophysics Data System (ADS)

Ermavitalini, Dini; Sari, Ika Puspita; Prasetyo, Endry Nugroho; Abdulgani, Nurlita; Saputro, Triono Bagus

2017-06-01

Nannochloropsissp. has been identified as a promising feed stock for biodiesel production in recent years. Nannochloropsis sp. have high lipid content between 31-68 % of dry biomass weight. Mutagenesis induced by Gamma 60Co irradiation can be utilized to alter Nannochloropsis sp. characteristic to get microalgae mutant strain that can produce a higher lipid content than the wild strain. The aim of this research was to know the effect of gamma 60Co irradiation to the biomass, lipid content and fatty acid compotition of Nannochloropsis sp. microalgae. In this research, irradiation was done in different doses there were 0, 2, 4, 6 and 10 Gray (Gy). Measuring microalgae biomass and lipid content were done in late exponential phase at the end of each treatment. Research design used is random complete with 95 % confident level for quantitative analysis based on biomass and lipid content. Fatty acid compotition was analyzed by gas chromatography-mass spectrometry (GC-MS). Results showed that gamma irradiated gave an effect on lipid content and fatty acid profile of Nannochloropsis sp. Tukey test showed total lipid content of control micoalgae (0 Gy) was significat different with 10 Gy irradiated microalgae, but no significant different with 2,4 and 6 Gy irradiated microalgae. The highest lipid content were found in 10 Gy irradiated microalgae equal to 62.65 %. Fatty acid profile of 10 Gy irradiated Nannochloropsis sp. had 9 fatty acids while control Nannochloropsis sp. had 6 fatty acids.

The application of two-step linear temperature program to thermal analysis for monitoring the lipid induction of Nostoc sp. KNUA003 in large scale cultivation.

PubMed

Kang, Bongmun; Yoon, Ho-Sung

2015-02-01

Recently, microalgae was considered as a renewable energy for fuel production because its production is nonseasonal and may take place on nonarable land. Despite all of these advantages, microalgal oil production is significantly affected by environmental factors. Furthermore, the large variability remains an important problem in measurement of algae productivity and compositional analysis, especially, the total lipid content. Thus, there is considerable interest in accurate determination of total lipid content during the biotechnological process. For these reason, various high-throughput technologies were suggested for accurate measurement of total lipids contained in the microorganisms, especially oleaginous microalgae. In addition, more advanced technologies were employed to quantify the total lipids of the microalgae without a pretreatment. However, these methods are difficult to measure total lipid content in wet form microalgae obtained from large-scale production. In present study, the thermal analysis performed with two-step linear temeperature program was applied to measure heat evolved in temperature range from 310 to 351 °C of Nostoc sp. KNUA003 obtained from large-scale cultivation. And then, we examined the relationship between the heat evolved in 310-351 °C (HE) and total lipid content of the wet Nostoc cell cultivated in raceway. As a result, the linear relationship was determined between HE value and total lipid content of Nostoc sp. KNUA003. Particularly, there was a linear relationship of 98% between the HE value and the total lipid content of the tested microorganism. Based on this relationship, the total lipid content converted from the heat evolved of wet Nostoc sp. KNUA003 could be used for monitoring its lipid induction in large-scale cultivation. Copyright © 2014 Elsevier Inc. All rights reserved.

Hydrothermal liquefaction of microalgae to produce biofuels: state of the art and future prospects

NASA Astrophysics Data System (ADS)

Vlaskin, M. S.; Chernova, N. I.; Kiseleva, S. V.; Popel', O. S.; Zhuk, A. Z.

2017-09-01

The article presents a review of the state of the art and lines of research on hydrothermal liquefaction (HTL) of microalgae (MA). The main advantages of this technology for production of biofuel are that it does not require predrying of the feedstock and ensures a relatively high product yield—the ratio of the end product weight to the feedstock weight—owing to the fact that all the microalgal components, viz., lipids, proteins, and carbohydrates, are converted into biofuel. MA hydrothermal liquefaction is considered to be a promising technology for conversion of biomass and is a subject of a series of research studies and, judging by the available publications, the scope of research in this field is expanding currently. However, many significant problems remain unsolved. In particular, an active searched is being conducted for suitable strains that will ensure not only a high lipid yield—necessary to convert microalgae into biodiesel—but also higher biomass productivity and a higher biofuel yield; the chemical reactions that occur during the hydrothermal treatment are being studied; and the effect of significant process variables, such as temperature, heating rate, holdup time at the maximum temperature, biomass concentration in the water suspension, biochemical and elemental compositions of the microalgae, use of catalysts, etc., on the liquefaction processes is being studied. One of the urgent tasks is also the reduction of the nitrogen content in the resulting biofuel. Studies aimed at the development of a continuous process and rational heat-processing plants for thermal microalgal conversion are being conducted to increase the energy efficiency of the HTL process, in particular, to provide the heat recovery and separation of the end product.

Contribution of benthic microalgae to the temporal variation in phytoplankton assemblages in a macrotidal system.

PubMed

Hernández Fariñas, Tania; Ribeiro, Lourenço; Soudant, Dominique; Belin, Catherine; Bacher, Cédric; Lampert, Luis; Barillé, Laurent

2017-10-01

Suspended marine benthic microalgae in the water column reflect the close relationship between the benthic and pelagic components of coastal ecosystems. In this study, a 12-year phytoplankton time-series was used to investigate the contribution of benthic microalgae to the pelagic system at a site along the French-Atlantic coast. Furthermore, all taxa identified were allocated into different growth forms in order to study their seasonal patterns. The highest contribution of benthic microalgae was observed during the winter period, reaching up to 60% of the carbon biomass in the water column. The haptobenthic growth form showed the highest contribution in terms of biomass, dominant in the fall-winter period when the turbidity and the river flow were high. The epipelic growth form did not follow any seasonal pattern. The epiphytic diatom Licmophora was most commonly found during summer. As benthic microalgae were found in the water column throughout the year, the temporal variation detected in the structure of pelagic assemblages in a macrotidal ecosystem was partly derived from the differentiated contribution of several benthic growth forms. © 2017 Phycological Society of America.

The Effects of Microalgae as Live Food for Brachionus plicatilis (Rotifer) in Intensive Culture System.

PubMed

Rahman, Abdull Razak Abd; Cob, Zaidi Che; Jamari, Zainoddin; Mohamed, Abdul Majid; Toda, Tatsuki; Ross, Othman Haji

2018-03-01

Brachionus plicatilis is used to feed fish and crustacean larvae in the aquaculture industry. It is well established that the type of microalgae may influence rotifer production. This experiment was conducted to determine the effect of five different locally available microalgae species at Fisheries Research Institute (FRI), Kampung Pulau Sayak, Kedah, Malaysia on the instantaneous growth rate (μ) of rotifer. Nannochloris sp., Tetraselmis sp., Isochrysis sp., Chlorella sp., and Nannochloropsis sp. were used as feed at different algae densities (0.1, 0.3, 0.7 and 1.5 × 10 6 cells/ml) and culture volumes (20, 70 and 210 ml). At algae densities ranging from 0.3 to 1.5 × 10 6 cells/ml, an average μ value of more than 0.90 per day were recorded for all algae species. However, at density of 0.1 × 10 6 cells/ml, only Tetraselmis sp. resulted in the significantly highest μ value compared with others ( p < 0.05). In terms of volume, smaller culture volume of Tetraselmis sp. (20 ml) showed significantly higher μ compared with higher volume (70 and 210 ml cultures).

Effect of operational conditions on the degradation of organic matter and development of microalgae-bacteria consortia when treating swine slurry.

PubMed

González-Fernández, Cristina; Riaño-Irazábal, Berta; Molinuevo-Salces, Beatriz; Blanco, Saúl; García-González, Maria Cruz

2011-05-01

There is great controversy regarding the best substrate (fresh or anaerobically digested swine slurry) for the development of microalgae-bacteria consortia. This study aims to elucidate the best substrate by assessing biomass productivity, microorganism predominance, and their ability for organic matter removal. In addition to the different substrates, different operational conditions and influent strengths were evaluated. Increasing organic matter content when favourable temperature and illumination conditions were present improved biomass production. However, these conditions were not favourable for microalgal growth, but they were favourable for bacteria. Regardless of the operational conditions, reactors fed with fresh slurry not only resulted in the highest biomass productivity, but also the greatest removal of total and soluble chemical oxygen demand (COD). On the other hand, reactors fed with digested slurry showed biomass productivity and COD removal values lower than those obtained for reactors fed with fresh slurry, most probably due to the recalcitrant nature of the former. Nevertheless, digested slurry was the substrate more appropriate for microalgae growth under harsh operational conditions (16 °C and 9-h illumination) at low influent strength and optimum operational conditions (30 °C and 24-h illumination) at higher influent strength.

Cultivation of Chlorella vulgaris in a pilot-scale photobioreactor using real centrate wastewater with waste glycerol for improving microalgae biomass production and wastewater nutrients removal.

PubMed

Ren, Hongyan; Tuo, Jinhua; Addy, Min M; Zhang, Renchuan; Lu, Qian; Anderson, Erik; Chen, Paul; Ruan, Roger

2017-12-01

To improve nutrients removal from real centrate wastewater and enhance the microalgae biomass production, cultivation of Chlorella vulgaris in lab and a pilot-scale photobioreactor with waste glycerol was studied. The results showed the optimal concentration of the crude glycerol was 1.0gL -1 with the maximum biomass productivity of 460mgL -1 d -1 TVS, the maximum lipid content of 27%, the nutrient removal efficiency of all above 86%, due to more balanced C/N ratio. The synergistic relationship between the wastewater-borne bacteria and the microalgae had significant good influence on nutrient removal. In pilot-scale wastewater-based algae cultivation, with 1gL -1 waste glycerol addition, the average biomass production of 16.7gm -2 d -1 , lipid content of 23.6%, and the removal of 2.4gm -2 d -1 NH 4 + -N, 2.7gm -2 d -1 total nitrogen, 3.0gm -2 d -1 total phosphorous, and 103.0gm -2 d -1 of COD were attained for 34days semi-continuous mode. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biodiesel production process from microalgae oil by waste heat recovery and process integration.

PubMed

Song, Chunfeng; Chen, Guanyi; Ji, Na; Liu, Qingling; Kansha, Yasuki; Tsutsumi, Atsushi

2015-10-01

In this work, the optimization of microalgae oil (MO) based biodiesel production process is carried out by waste heat recovery and process integration. The exergy analysis of each heat exchanger presented an efficient heat coupling between hot and cold streams, thus minimizing the total exergy destruction. Simulation results showed that the unit production cost of optimized process is 0.592$/L biodiesel, and approximately 0.172$/L biodiesel can be avoided by heat integration. Although the capital cost of the optimized biodiesel production process increased 32.5% and 23.5% compared to the reference cases, the operational cost can be reduced by approximately 22.5% and 41.6%. Copyright © 2015 Elsevier Ltd. All rights reserved.

A comparison of product yields and inorganic content in process streams following thermal hydrolysis and hydrothermal processing of microalgae, manure and digestate.

PubMed

Ekpo, U; Ross, A B; Camargo-Valero, M A; Williams, P T

2016-01-01

Thermal hydrolysis and hydrothermal processing show promise for converting biomass into higher energy density fuels. Both approaches facilitate the extraction of inorganics into the aqueous product. This study compares the behaviour of microalgae, digestate, swine and chicken manure by thermal hydrolysis and hydrothermal processing at increasing process severity. Thermal hydrolysis was performed at 170°C, hydrothermal carbonisation (HTC) was performed at 250°C, hydrothermal liquefaction (HTL) was performed at 350°C and supercritical water gasification (SCWG) was performed at 500°C. The level of nitrogen, phosphorus and potassium in the product streams was measured for each feedstock. Nitrogen is present in the aqueous phase as organic-N and NH3-N. The proportion of organic-N is higher at lower temperatures. Extraction of phosphorus is linked to the presence of inorganics such as Ca, Mg and Fe in the feedstock. Microalgae and chicken manure release phosphorus more easily than other feedstocks. Copyright © 2015. Published by Elsevier Ltd.

Life cycle assessment of microalgae-based aviation fuel: Influence of lipid content with specific productivity and nitrogen nutrient effects.

PubMed

Guo, Fang; Zhao, Jing; A, Lusi; Yang, Xiaoyi

2016-12-01

The aim of this work is to compare the life cycle assessments of low-N and normal culture conditions for a balance between the lipid content and specific productivity. In order to achieve the potential contribution of lipid content to the life cycle assessment, this study established relationships between lipid content (nitrogen effect) and specific productivity based on three microalgae strains including Chlorella, Isochrysis and Nannochloropsis. For microalgae-based aviation fuel, the effects of the lipid content on fossil fuel consumption and greenhouse gas (GHG) emissions are similar. The fossil fuel consumption (0.32-0.68MJ·MJ -1 MBAF) and GHG emissions (17.23-51.04gCO 2 e·MJ -1 MBAF) increase (59.70-192.22%) with the increased lipid content. The total energy input decreases (2.13-3.08MJ·MJ -1 MBAF, 14.91-27.95%) with the increased lipid content. The LCA indicators increased (0-47.10%) with the decreased nitrogen recovery efficiency (75-50%). Copyright © 2016 Elsevier Ltd. All rights reserved.

Cultivation of Chlorella protothecoides with urban wastewater in continuous photobioreactor: biomass productivity and nutrient removal.

PubMed

Ramos Tercero, E A; Sforza, E; Morandini, M; Bertucco, A

2014-02-01

The capability to grow microalgae in nonsterilized wastewater is essential for an application of this technology in an actual industrial process. Batch experiments were carried out with the species in nonsterilized urban wastewater from local treatment plants to measure both the algal growth and the nutrient consumption. Chlorella protothecoides showed a high specific growth rate (about 1 day(-1)), and no effects of bacterial contamination were observed. Then, this microalgae was grown in a continuous photobioreactor with CO₂-air aeration in order to verify the feasibility of an integrated process of the removal of nutrient from real wastewaters. Different residence times were tested, and biomass productivity and nutrients removal were measured. A maximum of microalgae productivity was found at around 0.8 day of residence time in agreement with theoretical expectation in the case of light-limited cultures. In addition, N-NH₄ and P-PO₄ removal rates were determined in order to model the kinetic of nutrients uptake. Results from batch and continuous experiments were used to propose an integrated process scheme of wastewater treatment at industrial scale including a section with C. protothecoides.

Microalgae as a feedstock for biofuel precursors and value-added products: Green fuels and golden opportunities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Yuting; Rosenberg, Julian N.; Bohutskyi, Pavlo

In this study, the prospects of biofuel production from microalgal carbohydrates and lipids coupled with greenhouse gas mitigation due to photosynthetic assimilation of CO 2 have ushered in a renewed interest in algal feedstock. Furthermore, microalgae (including cyanobacteria) have become established as commercial sources of value-added biochemicals such as polyunsaturated fatty acids and carotenoid pigments used as antioxidants in nutritional supplements and cosmetics. This article presents a comprehensive synopsis of the metabolic basis for accumulating lipids as well as applicable methods of lipid and cellulose bioconversion and final applications of these natural or refined products from microalgal biomass. For lipids,more » one-step in situ transesterification offers a new and more accurate approach to quantify oil content. As a complement to microalgal oil fractions, the utilization of cellulosic biomass from microalgae to produce bioethanol by fermentation, biogas by anaerobic digestion, and bio-oil by hydrothermal liquefaction are discussed. Collectively, a compendium of information spanning green renewable fuels and value-added nutritional compounds is provided.« less

Microalgae as a feedstock for biofuel precursors and value-added products: Green fuels and golden opportunities

DOE PAGES

Tang, Yuting; Rosenberg, Julian N.; Bohutskyi, Pavlo; ...

2015-11-16

In this study, the prospects of biofuel production from microalgal carbohydrates and lipids coupled with greenhouse gas mitigation due to photosynthetic assimilation of CO 2 have ushered in a renewed interest in algal feedstock. Furthermore, microalgae (including cyanobacteria) have become established as commercial sources of value-added biochemicals such as polyunsaturated fatty acids and carotenoid pigments used as antioxidants in nutritional supplements and cosmetics. This article presents a comprehensive synopsis of the metabolic basis for accumulating lipids as well as applicable methods of lipid and cellulose bioconversion and final applications of these natural or refined products from microalgal biomass. For lipids,more » one-step in situ transesterification offers a new and more accurate approach to quantify oil content. As a complement to microalgal oil fractions, the utilization of cellulosic biomass from microalgae to produce bioethanol by fermentation, biogas by anaerobic digestion, and bio-oil by hydrothermal liquefaction are discussed. Collectively, a compendium of information spanning green renewable fuels and value-added nutritional compounds is provided.« less

Retrofitting hetrotrophically cultivated algae biomass as pyrolytic feedstock for biogas, bio-char and bio-oil production encompassing biorefinery.

PubMed

Sarkar, Omprakash; Agarwal, Manu; Naresh Kumar, A; Venkata Mohan, S

2015-02-01

Algal biomass grown hetrotrophically in domestic wastewater was evaluated as pyrolytic feedstock for harnessing biogas, bio-oil and bio-char. Freshly harvested microalgae (MA) and lipid extracted microalgae (LEMA) were pyrolysed in packed bed reactor in the presence and absence of sand as additive. MA (without sand additive) depicted higher biogas (420 ml/g; 800 °C; 3 h) and bio-oil (0.70 ml/g; 500 °C; 3 h). Sand addition enhanced biogas production (210 ml/g; 600 °C; 2 h) in LEMA operation. The composition of bio-gas and bio-oil was found to depend on the nature of feedstock as well as the process conditions viz., pyrolytic-temperature, retention time and presence of additive. Sand additive improved the H2 composition while pyrolytic temperature increment caused a decline in CO2 fraction. Bio-char productivity increased with increasing temperature specifically with LEMA. Integration of thermo-chemical process with microalgae cultivation showed to yield multiple resources and accounts for environmental sustainability in the bio-refinery framework. Copyright © 2014 Elsevier Ltd. All rights reserved.

Growth of mono- and mixed cultures of Nannochloropsis salina and Phaeodactylum tricornutum on struvite as a nutrient source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Ryan W.; Siccardi, Anthony J.; Huysman, Nathan D.

In this paper, the suitability of crude and purified struvite (MgNH 4PO 4), a major precipitate in wastewater streams, was investigated for renewable replacement of conventional nitrogen and phosphate resources for cultivation of microalgae. Bovine effluent wastewater stone, the source of crude struvite, was characterized for soluble N/P, trace metals, and biochemical components and compared to the purified mineral. Cultivation trials using struvite as a major nutrient source were conducted using two microalgae production strains, Nannochloropsis salina and Phaeodactylum tricornutum, in both lab and outdoor pilot-scale raceways in a variety of seasonal conditions. Both crude and purified struvite-based media weremore » found to result in biomass productivities at least as high as established media formulations (maximum outdoor co-culture yield ~20 ± 4 g AFDW/m 2/day). Finally, analysis of nutrient uptake by the alga suggest that struvite provides increased nutrient utilization efficiency, and that crude struvite satisfies the trace metals requirement and results in increased pigment productivity for both microalgae strains.« less

Bioenergetic reprogramming plasticity under nitrogen depletion by the unicellular green alga Scenedesmus obliquus.

PubMed

Papazi, Aikaterini; Korelidou, Anna; Andronis, Efthimios; Parasyri, Athina; Stamatis, Nikolaos; Kotzabasis, Kiriakos

2018-03-01

Simultaneous nitrogen depletion and 3,4-dichlorophenol addition induce a bioenergetic microalgal reprogramming, through strong Cyt b 6 f synthesis, that quench excess electrons from dichlorophenol's biodegradation to an overactivated photosynthetic electron flow and H 2 -productivity. Cellular energy management includes "rational" planning and operation of energy production and energy consumption units. Microalgae seem to have the ability to calculate their energy reserves and select the most profitable bioenergetic pathways. Under oxygenic mixotrophic conditions, microalgae invest the exogenously supplied carbon source (glucose) to biomass increase. If 3,4-dichlorophenol is added in the culture medium, then glucose is invested more to biodegradation rather than to growth. The biodegradation yield is enhanced in nitrogen-depleted conditions, because of an increase in the starch accumulation and a delay in the establishment of oxygen-depleted conditions in a closed system. In nitrogen-depleted conditions, starch cannot be invested in PSII-dependent and PSII-independent pathways for H 2 -production, mainly because of a strong decrease of the cytochrome b 6 f complex of the photosynthetic electron flow. For this reason, it seems more profitable for the microalga under these conditions to direct the metabolism to the synthesis of lipids as cellular energy reserves. Nitrogen-depleted conditions with exogenously supplied 3,4-dichlorophenol induce reprogramming of the microalgal bioenergetic strategy. Cytochrome b 6 f is strongly synthesized (mainly through catabolism of polyamines) to manage the electron bypass from the dichlorophenol biodegradation procedure to the photosynthetic electron flow (at the level of PQ pool) and consequently through cytochrome b 6 f and PSI to hydrogenase and H 2 -production. All the above showed that the selection of the appropriate cultivation conditions is the key for the manipulation of microalgal bioenergetic strategy that leads to different metabolic products and paves the way for a future microalgal "smart" biotechnology.

Bicarbonate-based cultivation of Dunaliella salina for enhancing carbon utilization efficiency.

PubMed

Kim, Ga-Yeong; Heo, Jina; Kim, Hee-Sik; Han, Jong-In

2017-08-01

In this study, bicarbonate was proposed as an alternative carbon source to overcome exceedingly low CO 2 fixation efficiency of conventional microalgae cultivation system. 5gL -1 of sodium bicarbonate was found to well support the growth of Dunaliella salina, showing 2.84-fold higher specific growth rate than a bicarbonate-free control. This bicarbonate-fed cultivation also could yield biomass productivity similar to that of CO 2 -based system as long as pH was controlled. While the supplied CO 2 , because of its being a gas, was mostly lost and only 3.59% of it was used for biomass synthesis, bicarbonate was effectively incorporated into the biomass with 91.40% of carbon utilization efficiency. This study showed that the bicarbonate-based microalgae cultivation is indeed possible, and can even become a truly environment-friendly and workable approach, provided that a CO 2 mineralization technology is concomitantly established. Copyright © 2017 Elsevier Ltd. All rights reserved.

Pharming Pharmacopoeia: Living Apothecaries from the Sea

NASA Astrophysics Data System (ADS)

Baden, D. G.

2012-12-01

The quest for, and development of, new drugs to treat extant and emerging diseases is an interdisciplinary effort, often requiring isolation of pro-drugs from new organisms, environments, and species followed by activity measurement. Exploitation of cultivated microalgae from marine sources has produced some of the most potent natural biological agents known, with specific receptor-mediated activities in pulmonary medicine, toxicology, cancer chemotherapy, the cardiovascular system, central and peripheral nervous system, and in dermatology. Our recent discovery that one class of marine-derived molecule promotes trans-membrane transport, a second that enhances mucus secretion, and a third which is an inhibitor of inflammation--- all isolated from the same organism, highlights the increasingly broad potential for innovative exploitation of natural products that occur in marine microalgae. Approaches that include interdisciplinary teams, permanent innovation, and disruptive technologies all will be described in the context of discoveries made in the treatment of cystic fibrosis, in the improvement of drug efficacy, and in the development of multiple for translational sciences in the ocean and health arenas.

Growth, Proximate Composition and Pigment Production of Tetraselmis chuii Cultured with Aquaculture Wastewater

NASA Astrophysics Data System (ADS)

Khatoon, Helena; Haris, Haris; Rahman, Norazira Abdu; Zakaria, Mimi Nadzirah; Begum, Hasina; Mian, Sohel

2018-06-01

Microalgae are cultured commercially as healthy food, cosmetic products, food preservatives, and a source of valuable compounds. However, the high cost of commercial culture medium is one of the challenges to microalgal production. Therefore, it is essential to find an alternative cost-effective culture medium. Aquaculture wastewater is considered as a highly potential candidate due to its high nutrient content and large quantity generated from the rapid growth of aquaculture sector. In this study, Tetraselmis chuii cultured in different media with or without wastewater was evaluated for its growth, proximate composition and carotenoid production. The results showed that significantly ( P < 0.05) higher growth (4.3 × 105 cells mL-1) and protein (56.4% dry weight), lipid (44% dry weight) and carbohydrate (20% of dry weight) contents were found in T. chuii when they were cultured in the combination of both wastewater and Conway (wastewater + Conway) medium. However, carotenoid production of T. chuii was significantly increased ( P < 0.05) when it was cultured in wastewater only, followed by Conway + wastewater and Conway medium only. Therefore, the incorporation of wastewater with commercial medium Convey is recommended for a cost-effective microalgae culture, as well as for the enhancement of growth and nutritional content of microalgae.

The ΔF/Fm'-guided supply of nitrogen in culture medium facilitates sustainable production of TAG in Nannochloropsis oceanica IMET1.

PubMed

Liu, Jiao; Yao, Changhong; Meng, Yingying; Cao, Xupeng; Wu, Peichun; Xue, Song

2018-01-01

Triacylglycerol (TAG) from photosynthetic microalgae is a sustainable feedstock for biodiesel production. Physiological stress triggers microalgal TAG accumulation. However excessive physiological stress will impair the photosynthesis system seriously thus decreasing TAG productivity because of the low biomass production. Hence, it is critical to quantitatively and timely monitor the degree of the stress while the microalgal cells growing so that the optimal TAG productivity can be obtained. The lack of an on-line monitored indicator has limited our ability to gain knowledge of cellular "health status" information regarding high TAG productivity. Therefore, to monitor the degree of nitrogen stress of the cells, we investigated the correlation between the photosynthetic system II (PS II) quantum yield and the degree of stress based on the high relevancy between photosynthetic reduction and nitrogen stress-induced TAG accumulation in microalgal cells. Δ F/F m ', which is the chlorophyll fluorescence parameter that reflects the effective capability of PS II, was identified to be a critical factor to indicate the degree of stress of the cells. In addition, the concept of a nitrogen stress index has been defined to quantify the degree of stress. Based on this index and by monitoring Δ F/F m ' and guiding the supply of nitrogen in culture medium to maintain a stable degree of stress, a stable and efficient semi-continuous process for TAG production has been established. The results indicate that the semi-continuous cultivation process with a controlled degree of stress by monitoring the Δ F/F m ' indicator will have a significant impact on microalgal TAG production, especially for the outdoor controllable cultivation of microalgae on a large scale.

Development of Pollution Prevention Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Polle, Juergen; Sanchez-Delgado, Roberto

2013-12-30

This project investigated technologies that may reduce environmental pollution. This was a basic research/educational project addressing two major areas: A. In the algae research project, newly isolated strains of microalgae were investigated for feedstock production to address the production of renewable fuels. An existing collection of microalgae was screened for lipid composition to determine strains with superior composition of biofuel molecules. As many microalgae store triacylglycerides in so-called oil bodies, selected candidate strains identified from the first screen that accumulate oil bodies were selected for further biochemical analysis, because almost nothing was known about the biochemistry of these oil bodies.more » Understanding sequestration of triacylglycerides in intracellular storage compartments is essential to developing better strains for achieving high oil productivities by microalgae. At the onset of the project there was almost no information available on how to obtain detailed profiles of lipids from strains of microalgae. Our research developed analytical methods to determine the lipid profiles of novel microalgal strains. The project was embedded into other ongoing microalgal projects in the Polle laboratory. The project benefited the public, because students were trained in cell cultivation and in the operation of state-of-the-art analytical equipment. In addition, students at Brooklyn College were introduced into the concept of a systems biology approach to study algal biofuels production. B. A series of new nanostructured catalysts were synthesized, and characterized by a variety of physical and chemical methods. Our catalyst design leads to active nanostructures comprising small metal particles in intimate contact with strongly basic sites provided by the supports, which include poly(4-vinylpyridine), magnesium oxide, functionalized multi-walled carbon nanotubes, and graphene oxide. The new materials display a good potential as catalysts for reactions of relevance to the manufacture of cleaner fossil fuels and biodiesel, and to hydrogen storage in organic liquids. Specifically the catalysts are highly active in the hydrogenation of aromatic and heteroaromatic components of fossil fuels, the reduction of unsaturated C=C bonds in biodiesel, and the dehydrogenation of nitrogen heterocycles. In the course of our studies we identified a novel dual-site substrate-dependent hydrogenation mechanism that explains the activity and selectivity data obtained and the resistance of the new catalysts to poisoning. These results represent an important advance in basic catalytic science, regarding design and synthesis and reaction mechanisms. Additionally, this project allowed the enhancement of the laboratory facilities in the Chemistry Department of Brooklyn College for catalysis and energy research, and served as an excellent vehicle for the training of several young researchers at the undergraduate, graduate and postdoctoral level, to join the national scientific workforce.« less

Mussel beds are biological power stations on intertidal flats

NASA Astrophysics Data System (ADS)

Engel, Friederike G.; Alegria, Javier; Andriana, Rosyta; Donadi, Serena; Gusmao, Joao B.; van Leeuwe, Maria A.; Matthiessen, Birte; Eriksson, Britas Klemens

2017-05-01

Intertidal flats are highly productive areas that support large numbers of invertebrates, fish, and birds. Benthic diatoms are essential for the function of tidal flats. They fuel the benthic food web by forming a thin photosynthesizing compartment in the top-layer of the sediment that stretches over the vast sediment flats during low tide. However, the abundance and function of the diatom film is not homogenously distributed. Recently, we have realized the importance of bivalve reefs for structuring intertidal ecosystems; by creating structures on the intertidal flats they provide habitat, reduce hydrodynamic stress and modify the surrounding sediment conditions, which promote the abundance of associated organisms. Accordingly, field studies show that high chlorophyll a concentration in the sediment co-vary with the presence of mussel beds. Here we present conclusive evidence by a manipulative experiment that mussels increase the local biomass of benthic microalgae; and relate this to increasing biomass of microalgae as well as productivity of the biofilm across a nearby mussel bed. Our results show that the ecosystem engineering properties of mussel beds transform them into hot spots for primary production on tidal flats, highlighting the importance of biological control of sedimentary systems.

Engineering fatty acid biosynthesis in microalgae for sustainable biodiesel.

PubMed

Blatti, Jillian L; Michaud, Jennifer; Burkart, Michael D

2013-06-01

Microalgae are a promising feedstock for biodiesel and other liquid fuels due to their fast growth rate, high lipid yields, and ability to grow in a broad range of environments. However, many microalgae achieve maximal lipid yields only under stress conditions hindering growth and providing compositions not ideal for biofuel applications. Metabolic engineering of algal fatty acid biosynthesis promises to create strains capable of economically producing fungible and sustainable biofuels. The algal fatty acid biosynthetic pathway has been deduced by homology to bacterial and plant systems, and much of our understanding is gleaned from basic studies in these systems. However, successful engineering of lipid metabolism in algae will necessitate a thorough characterization of the algal fatty acid synthase (FAS) including protein-protein interactions and regulation. This review describes recent efforts to engineer fatty acid biosynthesis toward optimizing microalgae as a biodiesel feedstock. Copyright © 2013 Elsevier Ltd. All rights reserved.

Energy-producing electro-flocculation for harvest of Dunaliella salina.

PubMed

Liu, Qing; Zhang, Meng; Lv, Tao; Chen, Hongjun; Chika, Anthony Okonkwo; Xiang, Changli; Guo, Minxue; Wu, Minghui; Li, Jianjun; Jia, Lishan

2017-10-01

In this study, an efficient electro-flocculation process for Dunaliella salina with energy production by aluminum-air battery has been successfully applied. The formed aluminum hydroxide hydrates during discharging of battery were positively charged, which have a great potential for microalgae flocculation. The precipitation of aluminum hydroxide hydrates by algae also could improve the performance of aluminum-air battery. The harvesting efficiency could reach 97% in 20mins with energy production of 0.11kWh/kg. This discharging electro-flocculation (DEF) technology provides a new energy producing process to effectively harvest microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enzymatic cell disruption of microalgae biomass in biorefinery processes.

PubMed

Demuez, Marie; Mahdy, Ahmed; Tomás-Pejó, Elia; González-Fernández, Cristina; Ballesteros, Mercedes

2015-10-01

When employing biotechnological processes for the procurement of biofuels and bio-products from microalgae, one of the most critical steps affecting economy and yields is the "cell disruption" stage. Currently, enzymatic cell disruption has delivered effective and cost competitive results when compared to mechanical and chemical cell disruption methods. However, the introduction of enzymes implies additional associated cost within the overall process. In order to reduce this cost, autolysis of microalgae is proposed as alternative enzymatic cell disruption method. This review aims to provide the state of the art of enzymatic cell disruption treatments employed in biorefinery processes and highlights the use of endopeptidases. During the enzymatic processes of microalgae life cycle, some lytic enzymes involved in cell division and programmed cell death have been proven useful in performing cell lysis. In this context, the role of endopeptidases is emphasized. Mirroring these natural events, an alternative cell disruption approach is proposed and described with the potential to induce the autolysis process using intrinsic cell enzymes. Integrating induced autolysis within biofuel production processes offers a promising approach to reduce overall global costs and energetic input associated with those of current cell disruption methods. A number of options for further inquiry are also discussed. © 2015 Wiley Periodicals, Inc.

Investigation of Chlorella vulgaris UTEX 265 Cultivation under Light and Low Temperature Stressed Conditions for Lutein Production in Flasks and the Coiled Tree Photo-Bioreactor (CTPBR).

PubMed

Gong, Mengyue; Bassi, Amarjeet

2017-10-01

Lutein has an increasing share in the pharmaceutical and nutraceutical market due to its benefits to eye health. Microalgae may be a potential source for lutein production while the expense limits the commercialization. In this study, a coiled tubular tree photobioreactor (CTPBR) design was investigated for cultivating the cold tolerant microalgae Chlorella vulgaris UTEX 265 under various conditions for lutein production. The influence and interaction of light irradiance strength, lighting cycle, and temperature on microalgae and lutein production efficiency at low temperature range were also studied in flasks via response surface method (RSM). The results demonstrated that 14 h day-light, 120 μmol photons m -2  s -1 , and 10 °C was the optimal condition for algae growth and lutein production at low temperature experimental ranges. C. vulgaris UTEX 265 showed good potential to produce lutein in cold weather, and the optimum lutein production was contrary to the specific lutein content but corresponds to the trend of optimum growth. Additionally, fast growth (μ = 1.50 day -1 ) and good lutein recovery (11.98 mg g -1  day -1 ) in CTPBR were also achieved at the low irradiance stress condition and the low temperature photo-inhibition conditions.

Nitrogen starvation strategies and photobioreactor design for enhancing lipid content and lipid production of a newly isolated microalga Chlorella vulgaris ESP-31: implications for biofuels.

PubMed

Yeh, Kuei-Ling; Chang, Jo-Shu

2011-11-01

Microalgae are recognized for serving as a sustainable source for biodiesel production. This study investigated the effect of nitrogen starvation strategies and photobioreactor design on the performance of lipid production and of CO(2) fixation of an indigenous microalga Chlorella vulgaris ESP-31. Comparison of single-stage and two-stage nitrogen starvation strategies shows that single-stage cultivation on basal medium with low initial nitrogen source concentration (i.e., 0.313 g/L KNO(3)) was the most effective approach to enhance microalgal lipid production, attaining a lipid productivity of 78 mg/L/d and a lipid content of 55.9%. The lipid productivity of C. vulgaris ESP-31 was further upgraded to 132.4 mg/L/d when it was grown in a vertical tubular photobioreactor with a high surface to volume ratio of 109.3 m(2)/m(3) . The high lipid productivity was also accompanied by fixation of 6.36 g CO(2) during the 10-day photoautotrophic growth with a CO(2) fixation rate of 430 mg/L/d. Analysis of fatty acid composition of the microalgal lipid indicates that over 65% of fatty acids in the microalgal lipid are saturated [i.e., palmitic acid (C16:0) and stearic acid (C18:0)] and monounsaturated [i.e., oleic acid (C18:1)]. This lipid quality is suitable for biodiesel production. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microalgae and wastewater treatment

PubMed Central

Abdel-Raouf, N.; Al-Homaidan, A.A.; Ibraheem, I.B.M.

2012-01-01

Organic and inorganic substances which were released into the environment as a result of domestic, agricultural and industrial water activities lead to organic and inorganic pollution. The normal primary and secondary treatment processes of these wastewaters have been introduced in a growing number of places, in order to eliminate the easily settled materials and to oxidize the organic material present in wastewater. The final result is a clear, apparently clean effluent which is discharged into natural water bodies. This secondary effluent is, however, loaded with inorganic nitrogen and phosphorus and causes eutrophication and more long-term problems because of refractory organics and heavy metals that are discharged. Microalgae culture offers an interesting step for wastewater treatments, because they provide a tertiary biotreatment coupled with the production of potentially valuable biomass, which can be used for several purposes. Microalgae cultures offer an elegant solution to tertiary and quandary treatments due to the ability of microalgae to use inorganic nitrogen and phosphorus for their growth. And also, for their capacity to remove heavy metals, as well as some toxic organic compounds, therefore, it does not lead to secondary pollution. In the current review we will highlight on the role of micro-algae in the treatment of wastewater. PMID:24936135

Comparison of Chlorella vulgaris and cyanobacterial biomass: cultivation in urban wastewater and methane production.

PubMed

Mendez, Lara; Sialve, Bruno; Tomás-Pejó, Elia; Ballesteros, Mercedes; Steyer, Jean Philippe; González-Fernández, Cristina

2016-05-01

Anaerobic digestion of microalgae is hampered by its complex cell wall. Against this background, cyanobacteria cell walls render this biomass as an ideal substrate for overcoming this drawback. The aim of the present study was to compare the growth of two cyanobacteria (Aphanizomenon ovalisporum and Anabaena planctonica) and a microalga (Chlorella vulgaris) in urban wastewater when varying the temperature (22, 27 and 32 °C). Cyanobacterial optimal growth for both strains was attained at 22 °C, while C. vulgaris did not show remarkable differences among temperatures. For all the microorganisms, ammonium removal was higher than phosphate. Biomass collected was subjected to anaerobic digestion. Methane yield of C. vulgaris was 184.8 mL CH4 g COD in(-1) while with A. ovalisporum and A. planctonica the methane production was 1.2- and 1.4-fold higher. This study showed that cyanobacteria growth rates could be comparable to microalgae while presenting the additional benefit of an increased anaerobic digestibility.

Biorefinery integration of microalgae production into cassava processing industry: Potential and perspectives.

PubMed

de Carvalho, Júlio Cesar; Borghetti, Ivo Alberto; Cartas, Liliana Carrilo; Woiciechowski, Adenise Lorenci; Soccol, Vanete Thomaz; Soccol, Carlos Ricardo

2018-01-01

Cassava, the 5th most important staple crop, generates at least 600L of wastewater per ton of processed root. This residue, cassava processing wastewater (CPW) has a high chemical oxygen demand, that can reach 56 g/L, and has also high concentrations of several mineral nutrients. The cultivation of microalgae such as Chlorella, Spirulina and wild strains was evaluated in the last years in raw, minimally processed and partially digested CPW. Concentrations of 2-4 g/L of these microalgae, comparable to those obtained in synthetic media, could be reached. The BOD of the residue was reduced by up to 92%. This process can be integrated into cassava processing industries, if challenges such as the toxicity of the concentrated residue, bacterial contamination, and the isolation of robust strains are addressed. Because CPW carries about 11% of the crop energy, integrating biogas production and microalgal cultivation into the cassava processing chain is promising. Copyright © 2017 Elsevier Ltd. All rights reserved.

Toxicity assessment of pesticide triclosan by aquatic organisms and degradation studies.

PubMed

Taştan, Burcu Ertit; Tekinay, Turgay; Çelik, Hatice Sena; Özdemir, Caner; Cakir, Dilara Nur

2017-12-01

Triclosan is considered as an important contaminant and is widely used in personal care products as an antimicrobial agent. This study demonstrates the biodegradation of triclosan by two freshwater microalgae and the acute toxicity of triclosan and 2,4-dichlorophenol. The effects of culture media and light on biodegradation of triclosan and the changing morphology of microalgae were systematically studied. Geitlerinema sp. and Chlorella sp. degraded 82.10% and 92.83% of 3.99 mg/L of triclosan at 10 days, respectively. The microalgal growth inhibition assay confirmed absence of toxic effects of triclosan on Chlorella sp., even at higher concentration (50 mg/L) after 72 h exposure. HPLC analysis showed that 2,4-dichlorophenol was produced as degradation product of triclosan by Geitlerinema sp. and Chlorella sp. This study proved to be beneficial to understand biodegradation and acute toxicity of triclosan by microalgae in order to provide aquatic environmental protection. Copyright © 2017 Elsevier Inc. All rights reserved.

Diatoms Si uptake capacity drives carbon export in coastal upwelling systems

NASA Astrophysics Data System (ADS)

Abrantes, Fatima; Cermeno, Pedro; Lopes, Cristina; Romero, Oscar; Matos, Lélia; Van Iperen, Jolanda; Rufino, Marta; Magalhães, Vitor

2016-07-01

Coastal upwelling systems account for approximately half of global ocean primary production and contribute disproportionately to biologically driven carbon sequestration. Diatoms, silica-precipitating microalgae, constitute the dominant phytoplankton in these productive regions, and their abundance and assemblage composition in the sedimentary record is considered one of the best proxies for primary production. The study of the sedimentary diatom abundance (SDA) and total organic carbon content (TOC) in the five most important coastal upwelling systems of the modern ocean (Iberia-Canary, Benguela, Peru-Humboldt, California, and Somalia-Oman) reveals a global-scale positive relationship between diatom production and organic carbon burial. The analysis of SDA in conjunction with environmental variables of coastal upwelling systems such as upwelling strength, satellite-derived net primary production, and surface water nutrient concentrations shows different relations between SDA and primary production on the regional scale. On the global scale, SDA appears modulated by the capacity of diatoms to take up silicic acid, which ultimately sets an upper limit to global export production in these ocean regions.

Kinetic parameter estimation model for anaerobic co-digestion of waste activated sludge and microalgae.

PubMed

Lee, Eunyoung; Cumberbatch, Jewel; Wang, Meng; Zhang, Qiong

2017-03-01

Anaerobic co-digestion has a potential to improve biogas production, but limited kinetic information is available for co-digestion. This study introduced regression-based models to estimate the kinetic parameters for the co-digestion of microalgae and Waste Activated Sludge (WAS). The models were developed using the ratios of co-substrates and the kinetic parameters for the single substrate as indicators. The models were applied to the modified first-order kinetics and Monod model to determine the rate of hydrolysis and methanogenesis for the co-digestion. The results showed that the model using a hyperbola function was better for the estimation of the first-order kinetic coefficients, while the model using inverse tangent function closely estimated the Monod kinetic parameters. The models can be used for estimating kinetic parameters for not only microalgae-WAS co-digestion but also other substrates' co-digestion such as microalgae-swine manure and WAS-aquatic plants. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mixed Wastewater Coupled with CO2 for Microalgae Culturing and Nutrient Removal

PubMed Central

Yao, Lili; Shi, Jianye; Miao, Xiaoling

2015-01-01

Biomass, nutrient removal capacity, lipid productivity and morphological changes of Chlorella sorokiniana and Desmodesmus communis were investigated in mixed wastewaters with different CO2 concentrations. Under optimal condition, which was 1:3 ratio of swine wastewater to second treated municipal wastewater with 5% CO2, the maximum biomass concentrations were 1.22 g L-1 and 0.84 g L-1 for C. sorokiniana and D. communis, respectively. Almost all of the ammonia and phosphorus were removed, the removal rates of total nitrogen were 88.05% for C. sorokiniana and 83.18% for D. communis. Lipid content reached 17.04% for C. sorokiniana and 20.37% for D. communis after 10 days culture. CO2 aeration increased intracellular particle numbers of both microalgae and made D. communis tend to be solitary. The research suggested the aeration of CO2 improve the tolerance of microalgae to high concentration of NH4-N, and nutrient excess stress could induce lipid accumulation of microalgae. PMID:26418261

Innovative Alternative Technologies to Extract Carotenoids from Microalgae and Seaweeds

PubMed Central

Poojary, Mahesha M.; Barba, Francisco J.; Aliakbarian, Bahar; Donsì, Francesco; Pataro, Gianpiero; Dias, Daniel A.; Juliano, Pablo

2016-01-01

Marine microalgae and seaweeds (microalgae) represent a sustainable source of various bioactive natural carotenoids, including β-carotene, lutein, astaxanthin, zeaxanthin, violaxanthin and fucoxanthin. Recently, the large-scale production of carotenoids from algal sources has gained significant interest with respect to commercial and industrial applications for health, nutrition, and cosmetic applications. Although conventional processing technologies, based on solvent extraction, offer a simple approach to isolating carotenoids, they suffer several, inherent limitations, including low efficiency (extraction yield), selectivity (purity), high solvent consumption, and long treatment times, which have led to advancements in the search for innovative extraction technologies. This comprehensive review summarizes the recent trends in the extraction of carotenoids from microalgae and seaweeds through the assistance of different innovative techniques, such as pulsed electric fields, liquid pressurization, supercritical fluids, subcritical fluids, microwaves, ultrasounds, and high-pressure homogenization. In particular, the review critically analyzes technologies, characteristics, advantages, and shortcomings of the different innovative processes, highlighting the differences in terms of yield, selectivity, and economic and environmental sustainability. PMID:27879659

Wet in situ transesterification of microalgae using ethyl acetate as a co-solvent and reactant.

PubMed

Park, Jeongseok; Kim, Bora; Chang, Yong Keun; Lee, Jae W

2017-04-01

This study addresses wet in situ transesterification of microalgae for the production of biodiesel by introducing ethyl acetate as both reactant and co-solvent. Ethyl acetate and acid catalyst are mixed with wet microalgae in one pot and the mixture is heated for simultaneous lipid extraction and transesterification. As a single reactant and co-solvent, ethyl acetate can provide higher FAEE yield and more saccharification of carbohydrates than the case of binary ethanol and chloroform as a reactant and a co-solvent. The optimal yield was 97.8wt% at 114°C and 4.06M catalyst with 6.67mlEtOAC/g dried algae based on experimental results and response surface methodology (RSM). This wet in situ transesterification of microalgae using ethyl acetate doesn't require an additional co-solvent and it also promises more economic benefit as combining extraction and transesterification in a single process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nitrogen and phosphorus removal coupled with carbohydrate production by five microalgae cultures cultivated in biogas slurry.

PubMed

Tan, Fen; Wang, Zhi; Zhouyang, Siyu; Li, Heng; Xie, Youping; Wang, Yuanpeng; Zheng, Yanmei; Li, Qingbiao

2016-12-01

In this study, five microalgae strains were cultured for their ability to survive in biogas slurry, remove nitrogen resources and accumulate carbohydrates. It was proved that five microalgae strains adapted in biogas slurry well without ammonia inhibition. Among them, Chlorella vulgaris ESP-6 showed the best performance on carbohydrate accumulation, giving the highest carbohydrate content of 61.5% in biogas slurry and the highest ammonia removal efficiency and rate of 96.3% and 91.7mg/L/d respectively in biogas slurry with phosphorus and magnesium added. Additionally, the absence of phosphorus and magnesium that can be adverse for biomass accumulation resulted in earlier timing of carbohydrate accumulation and magnesium was firstly recognized and proved as the influence factor for carbohydrate accumulation. Microalgae that cultured in biogas slurry accumulated more carbohydrate in cell, making biogas slurry more suitable medium for the improvement of carbohydrate content, thus can be regarded as a new strategy to accumulate carbohydrate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bioethanol production from the nutrient stress-induced microalga Chlorella vulgaris by enzymatic hydrolysis and immobilized yeast fermentation.

PubMed

Kim, Kyoung Hyoun; Choi, In Seong; Kim, Ho Myeong; Wi, Seung Gon; Bae, Hyeun-Jong

2014-02-01

The microalga Chlorella vulgaris is a potential feedstock for bioenergy due to its rapid growth, carbon dioxide fixation efficiency, and high accumulation of lipids and carbohydrates. In particular, the carbohydrates in microalgae make them a candidate for bioethanol feedstock. In this study, nutrient stress cultivation was employed to enhance the carbohydrate content of C. vulgaris. Nitrogen limitation increased the carbohydrate content to 22.4% from the normal content of 16.0% on dry weight basis. In addition, several pretreatment methods and enzymes were investigated to increase saccharification yields. Bead-beating pretreatment increased hydrolysis by 25% compared with the processes lacking pretreatment. In the enzymatic hydrolysis process, the pectinase enzyme group was superior for releasing fermentable sugars from carbohydrates in microalgae. In particular, pectinase from Aspergillus aculeatus displayed a 79% saccharification yield after 72h at 50°C. Using continuous immobilized yeast fermentation, microalgal hydrolysate was converted into ethanol at a yield of 89%. Copyright © 2013 Elsevier Ltd. All rights reserved.

Microalgae as substrate in low cost terracotta-based microbial fuel cells: Novel application of the catholyte produced.

PubMed

Salar-García, M J; Gajda, I; Ortiz-Martínez, V M; Greenman, J; Hanczyc, M M; de los Ríos, A P; Ieropoulos, I A

2016-06-01

In this work, the by-product generated during the operation of cylindrical MFCs, made out of terracotta material, is investigated as a feasible means of degrading live microalgae for the first time. In addition to the low cost materials of this design, the reuse of the solution produced in the cathode renders the technology truly green and capable of generating bioenergy. In this study, the effect of a light/dark cycle or dark conditions only on the digestion of live microalgae with the catholyte is investigated. The results show that a combination of light/dark improves degradation and allows algae to be used as substrate in the anode. The addition of 12.5mL of a 1:1 mix of catholyte and microalgae (pre-digested over 5days under light/dark) to the anode, increases the power generation from 7μW to 44μW once all the organic matter in the anode had been depleted. Copyright © 2016 Elsevier Ltd. All rights reserved.

Innovative Alternative Technologies to Extract Carotenoids from Microalgae and Seaweeds.

PubMed

Poojary, Mahesha M; Barba, Francisco J; Aliakbarian, Bahar; Donsì, Francesco; Pataro, Gianpiero; Dias, Daniel A; Juliano, Pablo

2016-11-22

Marine microalgae and seaweeds (microalgae) represent a sustainable source of various bioactive natural carotenoids, including β-carotene, lutein, astaxanthin, zeaxanthin, violaxanthin and fucoxanthin. Recently, the large-scale production of carotenoids from algal sources has gained significant interest with respect to commercial and industrial applications for health, nutrition, and cosmetic applications. Although conventional processing technologies, based on solvent extraction, offer a simple approach to isolating carotenoids, they suffer several, inherent limitations, including low efficiency (extraction yield), selectivity (purity), high solvent consumption, and long treatment times, which have led to advancements in the search for innovative extraction technologies. This comprehensive review summarizes the recent trends in the extraction of carotenoids from microalgae and seaweeds through the assistance of different innovative techniques, such as pulsed electric fields, liquid pressurization, supercritical fluids, subcritical fluids, microwaves, ultrasounds, and high-pressure homogenization. In particular, the review critically analyzes technologies, characteristics, advantages, and shortcomings of the different innovative processes, highlighting the differences in terms of yield, selectivity, and economic and environmental sustainability.

Advances in the biotechnology of hydrogen production with the microalga Chlamydomonas reinhardtii.

PubMed

Torzillo, Giuseppe; Scoma, Alberto; Faraloni, Cecilia; Giannelli, Luca

2015-01-01

Biological hydrogen production is being evaluated for use as a fuel, since it is a promising substitute for carbonaceous fuels owing to its high conversion efficiency and high specific energy content. The basic advantages of biological hydrogen production over other "green" energy sources are that it does not compete for agricultural land use, and it does not pollute, as water is the only by-product of the combustion. These characteristics make hydrogen a suitable fuel for the future. Among several biotechnological approaches, photobiological hydrogen production carried out by green microalgae has been intensively investigated in recent years. A select group of photosynthetic organisms has evolved the ability to harness light energy to drive hydrogen gas production from water. Of these, the microalga Chlamydomonas reinhardtii is considered one of the most promising eukaryotic H2 producers. In this model microorganism, light energy, H2O and H2 are linked by two excellent catalysts, the photosystem 2 (PSII) and the [FeFe]-hydrogenase, in a pathway usually referred to as direct biophotolysis. This review summarizes the main advances made over the past decade as an outcome of the discovery of the sulfur-deprivation process. Both the scientific and technical barriers that need to be overcome before H2 photoproduction can be scaled up to an industrial level are examined. Actual and theoretical limits of the efficiency of the process are also discussed. Particular emphasis is placed on algal biohydrogen production outdoors, and guidelines for an optimal photobioreactor design are suggested.

Improving the feasibility of producing biofuels from microalgae using wastewater.

PubMed

Rawat, I; Bhola, V; Kumar, R Ranjith; Bux, F

2013-01-01

Biofuels have received much attention recently owing to energy consumption and environmental concerns. Despite many of the technologies being technically feasible, the processes are often too costly to be commercially viable. The major stumbling block to full-scale production of algal biofuels is the cost of upstream and downstream processes and environmental impacts such as water footprint and indirect greenhouse gas emissions from chemical nutrient production. The technoeconomics of biofuels production from microalgae is currently unfeasible due to the cost of inputs and productivities achieved. The use of a biorefinery approach sees the production costs reduced greatly due to utilization of waste streams for cultivation and the generation of several potential energy sources and value-added products while offering environmental protection. The use of wastewater as a production media, coupled with CO2 sequestration from flue gas greatly reduces the microalgal cultivation costs. Conversion of residual biomass and by-products, such as glycerol, for fuel production using an integrated approach potentially holds the key to near future commercial implementation of biofuels production.

Operation optimization of a photo-sequencing batch reactor for wastewater treatment: Study on influencing factors and impact on symbiotic microbial ecology.

PubMed

Ye, Jianfeng; Liang, Junyu; Wang, Liang; Markou, Giorgos; Jia, Qilong

2018-03-01

Wastewater treatment technology with better energy efficiency and recyclability is in urgent demand. Photo-Sequencing batch reactor (SBR), which introduces microalgae into conventional SBR, is considered to have more potential for resource recycling. In this study, a photo-SBR was evaluated through the manipulation of several key operational parameters, i.e., aeration strength, light supply intensity and time per cycle, and solid retention time (SRT). The algal-bacterial symbiotic system had the potential of removing COD, NH 4 + -N and TN with limited aeration, representing the advantage of energy-saving by low aeration requirement. Maintaining appropriate proportion of microalgae in the symbiotic system is critical for good system performance. Introducing microalgae into conventional SBR has obvious impact on the original microbial ecology. When the concentration of microalgae is too high (>4.60 mg Chl/L), the inhibition on certain phyla of bacteria, e.g., Bacteroidetes and Actinobacteria, would become prominent and not conducive to the stable operation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enhanced biodiesel production in Neochloris oleoabundans by a semi-continuous process in two stage photobioreactors.

PubMed

Yoon, Se Young; Hong, Min Eui; Chang, Won Seok; Sim, Sang Jun

2015-07-01

Under autotrophic conditions, highly productive biodiesel production was achieved using a semi-continuous culture system in Neochloris oleoabundans. In particular, the flue gas generated by combustion of liquefied natural gas and natural solar radiation were used for cost-effective microalgal culture system. In semi-continuous culture, the greater part (~80%) of the culture volume containing vegetative cells grown under nitrogen-replete conditions in a first photobioreactor (PBR) was directly transferred to a second PBR and cultured sequentially under nitrogen-deplete conditions for accelerating oil accumulation. As a result, in semi-continuous culture, the productivities of biomass and biodiesel in the cells were increased by 58% (growth phase) and 51% (induction phase) compared to the cells in batch culture, respectively. The semi-continuous culture system using two stage photobioreactors is a very efficient strategy to further improve biodiesel production from microalgae under photoautotrophic conditions.

The influences of the recycle process on the bacterial community in a pilot scale microalgae raceway pond.

PubMed

Erkelens, Mason; Ball, Andrew S; Lewis, David M

2014-04-01

The use of recycled media has been shown to be a necessary step within the lifecycle of microalgal biofuels for economic sustainability and reducing the water footprint. However the impact of the harvesting of microalgae on the bacterial load of the recycled water has yet to be investigated. Within this study PCR-DGGE and real-time PCR was used to evaluate the bacterial community dynamics within the recycled water following harvest and concentration steps for a pilot scale open pond system (120,000L), which was developed for the production of green crude oil from Tetraselmis sp. in hyper saline water. Two stages were used in the harvesting; Stage 1 electroflocculation, and Stage 2 centrifugation. Electroflocculation was shown to have little effect on the bacterial cell concentration. In contrast bacterial diversity and cell concentration within the centrifugation step was greatly reduced. Copyright © 2014 Elsevier Ltd. All rights reserved.

The use of natural infochemicals for sustainable and efficient harvesting of the microalgae Scenedesmus spp. for biotechnology: insights from a meta-analysis.

PubMed

Roccuzzo, Sebastiana; Beckerman, Andrew P; Pandhal, Jagroop

2016-12-01

Open raceway ponds are regarded as the most economically viable option for large-scale cultivation of microalgae for low to mid-value bio-products, such as biodiesel. However, improvements are required including reducing the costs associated with harvesting biomass. There is now a growing interest in exploiting natural ecological processes within biotechnology. We review how chemical cues produced by algal grazers induce colony formation in algal cells, which subsequently leads to their sedimentation. A statistical meta-analysis of more than 80 studies reveals that Daphnia grazers can induce high levels of colony formation and sedimentation in Scenedesmus obliquus and that these natural, infochemical induced sedimentation rates are comparable to using commercial chemical equivalents. These data suggest that natural ecological interactions can be co-opted in biotechnology as part of a promising, low energy and clean harvesting method for use in large raceway systems.

Growth and metabolic characteristics of oleaginous microalgal isolates from Nilgiri biosphere Reserve of India.

PubMed

Thangavel, Kalaiselvi; Radha Krishnan, Preethi; Nagaiah, Srimeena; Kuppusamy, Senthil; Chinnasamy, Senthil; Rajadorai, Jude Sudhagar; Nellaiappan Olaganathan, Gopal; Dananjeyan, Balachandar

2018-01-03

Renewable energy for sustainable development is a subject of a worldwide debate since continuous utilization of non-renewable energy sources has a drastic impact on the environment and economy; a search for alternative energy resources is indispensable. Microalgae are promising and potential alternate energy resources for biodiesel production. Thus, our efforts were focused on surveying the natural diversity of microalgae for the production of biodiesel. The present study aimed at identification, isolation, and characterization of oleaginous microalgae from shola forests of Nilgiri Biosphere Reserve (NBR), the biodiversity hot spot of India, where the microalgal diversity has not yet been systematically investigated. Overall the higher biomass yield, higher lipid accumulation and thermotolerance observed in the isolated microalgal strains have been found to be the desirable traits for the efficient biodiesel production. Species composition and diversity analysis yielded ten potential microalgal isolates belonging to Chlorophyceae and Cyanophyceae classes. The chlorophytes exhibited higher growth rate, maximum biomass yield, and higher lipid accumulation than Cyanophyceae. Among the chlorophytes, the best performing strains were identified and represented by Acutodesmus dissociatus (TGA1), Chlorella sp. (TGA2), Chlamydomonadales sp. (TGA3) and Hindakia tetrachotoma (PGA1). The Chlamydomonadales sp. recorded with the highest growth rate, lipid accumulation and biomass yield of 0.28 ± 0.03 day -1 (μ exp ), 29.7 ± 0.69% and 134.17 ± 16.87 mg L -1  day -1 , respectively. It was also found to grow well at various temperatures, viz., 25 °C, 35 °C, and 45 °C, indicating its suitability for open pond cultivation. The fatty acid methyl ester (FAME) analysis of stationary phase cultures of selected four algal strains by tandem mass spectrograph showed C16:0, C18:1 and C18:3 as dominant fatty acids suitable for biodiesel production. All the three strains except for Hindakia tetrachotoma (PGA1) recorded higher carbohydrate content and were considered as potential feed stocks for biodiesel production through hydrothermal liquefaction technology (HTL). In conclusion, the present investigation is a first systematic study on the microalgal diversity of soil and water samples from selected sites of NBR. The study resulted in isolation and characterization of ten potent oleaginous microalgae and found four cultures as promising feed stocks for biodiesel production. Of the four microalgae, Chlamydomonadales sp. (TGA3) was found to be significantly thermo-tolerant and can be considered as promising feedstock for biodiesel production.

Improving biogas production from microalgae by enzymatic pretreatment.

PubMed

Passos, Fabiana; Hom-Diaz, Andrea; Blanquez, Paqui; Vicent, Teresa; Ferrer, Ivet

2016-01-01

In this study, enzymatic pretreatment of microalgal biomass was investigated under different conditions and evaluated using biochemical methane potential (BMP) tests. Cellulase, glucohydrolase and an enzyme mix composed of cellulase, glucohydrolase and xylanase were selected based on the microalgae cell wall composition (cellulose, hemicellulose, pectin and glycoprotein). All of them increased organic matter solubilisation, obtaining high values already after 6h of pretreatment with an enzyme dose of 1% for cellulase and the enzyme mix. BMP tests with pretreated microalgae showed a methane yield increase of 8 and 15% for cellulase and the enzyme mix, respectively. Prospective research should evaluate enzymatic pretreatments in continuous anaerobic reactors so as to estimate the energy balance and economic cost of the process. Copyright © 2015 Elsevier Ltd. All rights reserved.

An interactive tool for outdoor computer controlled cultivation of microalgae in a tubular photobioreactor system.

PubMed

Dormido, Raquel; Sánchez, José; Duro, Natividad; Dormido-Canto, Sebastián; Guinaldo, María; Dormido, Sebastián

2014-03-06

This paper describes an interactive virtual laboratory for experimenting with an outdoor tubular photobioreactor (henceforth PBR for short). This virtual laboratory it makes possible to: (a) accurately reproduce the structure of a real plant (the PBR designed and built by the Department of Chemical Engineering of the University of Almería, Spain); (b) simulate a generic tubular PBR by changing the PBR geometry; (c) simulate the effects of changing different operating parameters such as the conditions of the culture (pH, biomass concentration, dissolved O2, inyected CO2, etc.); (d) simulate the PBR in its environmental context; it is possible to change the geographic location of the system or the solar irradiation profile; (e) apply different control strategies to adjust different variables such as the CO2 injection, culture circulation rate or culture temperature in order to maximize the biomass production; (f) simulate the harvesting. In this way, users can learn in an intuitive way how productivity is affected by any change in the design. It facilitates the learning of how to manipulate essential variables for microalgae growth to design an optimal PBR. The simulator has been developed with Easy Java Simulations, a freeware open-source tool developed in Java, specifically designed for the creation of interactive dynamic simulations.

An Interactive Tool for Outdoor Computer Controlled Cultivation of Microalgae in a Tubular Photobioreactor System

PubMed Central

Dormido, Raquel; Sánchez, José; Duro, Natividad; Dormido-Canto, Sebastián; Guinaldo, María; Dormido, Sebastián

2014-01-01

This paper describes an interactive virtual laboratory for experimenting with an outdoor tubular photobioreactor (henceforth PBR for short). This virtual laboratory it makes possible to: (a) accurately reproduce the structure of a real plant (the PBR designed and built by the Department of Chemical Engineering of the University of Almería, Spain); (b) simulate a generic tubular PBR by changing the PBR geometry; (c) simulate the effects of changing different operating parameters such as the conditions of the culture (pH, biomass concentration, dissolved O2, inyected CO2, etc.); (d) simulate the PBR in its environmental context; it is possible to change the geographic location of the system or the solar irradiation profile; (e) apply different control strategies to adjust different variables such as the CO2 injection, culture circulation rate or culture temperature in order to maximize the biomass production; (f) simulate the harvesting. In this way, users can learn in an intuitive way how productivity is affected by any change in the design. It facilitates the learning of how to manipulate essential variables for microalgae growth to design an optimal PBR. The simulator has been developed with Easy Java Simulations, a freeware open-source tool developed in Java, specifically designed for the creation of interactive dynamic simulations. PMID:24662450

Mathematical modeling of unicellular microalgae and cyanobacteria metabolism for biofuel production.

PubMed

Baroukh, Caroline; Muñoz-Tamayo, Rafael; Bernard, Olivier; Steyer, Jean-Philippe

2015-06-01

The conversion of microalgae lipids and cyanobacteria carbohydrates into biofuels appears to be a promising source of renewable energy. This requires a thorough understanding of their carbon metabolism, supported by mathematical models, in order to optimize biofuel production. However, unlike heterotrophic microorganisms that utilize the same substrate as sources of energy and carbon, photoautotrophic microorganisms require light for energy and CO2 as carbon source. Furthermore, they are submitted to permanent fluctuating light environments due to outdoor cultivation or mixing inducing a flashing effect. Although, modeling these nonstandard organisms is a major challenge for which classical tools are often inadequate, this step remains a prerequisite towards efficient optimization of outdoor biofuel production at an industrial scale. Copyright © 2015 Elsevier Ltd. All rights reserved.

The development of microalgal biotechnology in the Czech Republic.

PubMed

Masojídek, Jiří; Prášil, Ondřej

2010-12-01

Microscopic algae and cyanobacteria are excellent sources of numerous compounds, from raw biomass rich in proteins, oils, and antioxidants to valuable secondary metabolites with potential medical use. In the former Czechoslovakia, microalgal biotechnology developed rapidly in the 1960s with the main aim of providing industrial, high-yield sources of algal biomass. Unique cultivation techniques that are still in use were successfully developed and tested. Gradually, the focus changed from bulk production to more sophisticated use of microalgae, including production of bioactive compounds. Along the way, better understanding of the physiology and cell biology of productive microalgal strains was achieved. Currently, microalgae are in the focus again, mostly as possible sources of bioactive compounds and next-generation biofuels for the 21st century.

Recent Developments in Production and Biotechnological Applications of C-Phycocyanin

PubMed Central

Kuddus, M.; Singh, P.; Thomas, G.; Al-Hazimi, Awdah

2013-01-01

An extensive range of pigments including phycobiliproteins are present in algae. C-phycocyanin (C-PC), a phycobiliprotein, is one of the key pigments of Spirulina, a microalgae used in many countries as a dietary supplement. Algal pigments have massive commercial value as natural colorants in nutraceutical, cosmetics, and pharmaceutical industries, besides their health benefits. At present, increasing awareness of harmful effects of synthetic compounds and inclination of community towards the usage of natural products have led to the exploitation of microalgae as a source of natural pigments/colors. This review describes recent findings about the sources and production of C-PC, with emphasis on specific techniques for extraction and purification, along with potential industrial applications in diagnostics, foods, cosmetics, and pharmaceutical industries. PMID:24063013

Recent developments in production and biotechnological applications of C-phycocyanin.

PubMed

Kuddus, M; Singh, P; Thomas, G; Al-Hazimi, Awdah

2013-01-01

An extensive range of pigments including phycobiliproteins are present in algae. C-phycocyanin (C-PC), a phycobiliprotein, is one of the key pigments of Spirulina, a microalgae used in many countries as a dietary supplement. Algal pigments have massive commercial value as natural colorants in nutraceutical, cosmetics, and pharmaceutical industries, besides their health benefits. At present, increasing awareness of harmful effects of synthetic compounds and inclination of community towards the usage of natural products have led to the exploitation of microalgae as a source of natural pigments/colors. This review describes recent findings about the sources and production of C-PC, with emphasis on specific techniques for extraction and purification, along with potential industrial applications in diagnostics, foods, cosmetics, and pharmaceutical industries.

Microalgal process-monitoring based on high-selectivity spectroscopy tools: status and future perspectives.

PubMed

Podevin, Michael; Fotidis, Ioannis A; Angelidaki, Irini

2018-08-01

Microalgae are well known for their ability to accumulate lipids intracellularly, which can be used for biofuels and mitigate CO 2 emissions. However, due to economic challenges, microalgae bioprocesses have maneuvered towards the simultaneous production of food, feed, fuel, and various high-value chemicals in a biorefinery concept. On-line and in-line monitoring of macromolecules such as lipids, proteins, carbohydrates, and high-value pigments will be more critical to maintain product quality and consistency for downstream processing in a biorefinery to maintain and valorize these markets. The main contribution of this review is to present current and prospective advances of on-line and in-line process analytical technology (PAT), with high-selectivity - the capability of monitoring several analytes simultaneously - in the interest of improving product quality, productivity, and process automation of a microalgal biorefinery. The high-selectivity PAT under consideration are mid-infrared (MIR), near-infrared (NIR), and Raman vibrational spectroscopies. The current review contains a critical assessment of these technologies in the context of recent advances in software and hardware in order to move microalgae production towards process automation through multivariate process control (MVPC) and software sensors trained on "big data". The paper will also include a comprehensive overview of off-line implementations of vibrational spectroscopy in microalgal research as it pertains to spectral interpretation and process automation to aid and motivate development.

Domestic wastewater treatment and biofuel production by using microalga Scenedesmus sp. ZTY1.

PubMed

Zhang, Tian-Yuan; Wu, Yin-Hu; Hu, Hong-Ying

2014-01-01

Cultivation of microalgae for biomass production is a promising way to dispose of wastewater and recover nutrients simultaneously. The properties of nutrient removal and biomass production in domestic wastewater of a newly isolated microalga Scenedesmus sp. ZTY1 were investigated in this study. Scenedesmus sp. ZTY1, which was isolated from a wastewater treatment plant in Beijing, grew well in both the primary and secondary effluents of a wastewater treatment plant during the 21-day cultivation, with a maximal algal density of 3.6 × 10(6) and 1.9 × 10(6) cells · mL(-1), respectively. The total phosphorus concentrations in both effluents could be efficiently removed by over 97% after the cultivation. A high removal rate (over 90%) of total nitrogen (TN) was also observed. After cultivation in primary effluent for 21 days, the lipid content of Scenedesmus sp. ZTY1 in dry weight had reached about 32.2%. The lipid and triacylglycerol (TAG) production of Scenedesmus sp. ZTY1 was increased significantly with the extension of cultivation time. The TAG production of Scenedesmus sp. ZTY1 increased from 32 mg L(-1) at 21 d to 148 mg L(-1) at 45 d in primary effluent. All the experiments were carried out in non-sterilized domestic wastewater and Scenedesmus sp. ZTY1 showed good adaptability to the domestic wastewater environment.

Oleaginous Microalgae from Dairy Farm Wastewater for Biodiesel Production: Isolation, Characterization and Mass Cultivation.

PubMed

Sun, Zheng; Fang, Xiao-Peng; Li, Xiao-Yang; Zhou, Zhi-Gang

2018-02-01

Producing biodiesel from microalgae grown in wastewater is environment-friendly and cost-effective. The present study investigated the algae found in wastewater of a local dairy farm for their potential as biodiesel feedstocks. Thirteen native algal strains were isolated. On the basis of morphology and 16S/18S rRNA gene sequences, one strain was identified to be a member of cyanobacteria, while other 12 strains belong to green algae. After screening, two Scenedesmus strains out of the 13 microalgae isolates demonstrated superiority in growth rate, lipid productivity, and sedimentation properties, and therefore were selected for further scale-up outdoor cultivation. Both Scenedesmus strains quickly adapted to the outdoor conditions, exhibiting reasonably good growth and strong anti-contamination capabilities. In flat-plate photobioreactors (PBRs), algal cells accumulated predominantly neutral lipids that accounted for over 60% of total lipids with almost 70% being triacylglycerol. In addition, Scenedesmus obliquus had a high content of monounsaturated fatty acids, of which the amount of oleic acid (C18:1) was up to 27.11%. Based on these findings, the dairy farm wastewater-isolated Scenedesmus strains represent promising sources of low-cost, high-quality oil for biofuel production.

Comparison of nutrient removal capacity and biomass settleability of four high-potential microalgal species.

PubMed

Su, Yanyan; Mennerich, Artur; Urban, Brigitte

2012-11-01

Four common used microalgae species were compared in terms of settleability, nutrient removal capacity and biomass productivity. After 1 month training, except cyanobacteria Phormidium sp., three green microalgae species, Chlamydomonas reinhardtii, Chlorella vulgaris and Scenedesmus rubescens, showed good settleability. The N and P removal efficiency was all above 99% within 7, 4, 6 and 6 days for N and 4, 2, 3 and 4 days for P, resulting in the N removal rates of 3.66±0.17, 6.39±0.20, 4.39±0.06 and 4.31±0.18 mg N/l/d and P removal rates of 0.56±0.07, 0.89±0.05, 0.76±0.09 and 0.60±0.05 mg P/l/d for Phormidium sp., C. reinhardtii, C. vulgaris and S. rubescens, respectively. Phormidium sp. had the lowest algal biomass productivity (2.71±0.7 g/m(2)/d) and the other three green microalgae showed higher algal biomass productivity (around 6 g/m(2)/d). Assimilation into biomass was the main removal mechanism for N and P. Copyright © 2012 Elsevier Ltd. All rights reserved.

Enhanced lipid accumulation of green microalga Scenedesmus sp. by metal ions and EDTA addition.

PubMed

Ren, Hong-Yu; Liu, Bing-Feng; Kong, Fanying; Zhao, Lei; Xie, Guo-Jun; Ren, Nan-Qi

2014-10-01

Effects of Fe(3+) (0-0.12 g/L), Mg(2+) (0-0.73 g/L) and Ca(2+) (0-0.98 g/L) on the biomass and lipid accumulation of heterotrophic microalgae were investigated in dark environment. The biomass and lipid production exhibited an increasing trend with increasing the concentrations of metal ions. In cultures with 1.2 × 10(-3) g/L Fe(3+), 7.3 × 10(-3) g/L Mg(2+) and 9.8 × 10(-4) g/L Ca(2+), the maximum biomass, total lipid content and lipid productivity reached 3.49 g/L, 47.4% and 275.7 mg/L/d, respectively. More importantly, EDTA addition (1.0 × 10(-3) g/L) could enhance the solubility of metal ions (iron and calcium) and increase their availability by microalgae, which evidently promote the lipid accumulation. Compared with the control, the total lipid content and lipid productivity increased 28.2% and 29.7%, respectively. These show that appropriate concentrations of metal ions and EDTA in the culture medium were beneficial to lipid accumulation of heterotrophic Scenedesmus sp. cells. Copyright © 2014 Elsevier Ltd. All rights reserved.

Modeling Microalgae Productivity in Industrial-Scale Vertical Flat Panel Photobioreactors.

PubMed

Endres, Christian H; Roth, Arne; Brück, Thomas B

2018-05-01

Potentially achievable biomass yields are a decisive performance indicator for the economic viability of mass cultivation of microalgae. In this study, a computer model has been developed and applied to estimate the productivity of microalgae for large-scale outdoor cultivation in vertical flat panel photobioreactors. Algae growth is determined based on simulations of the reactor temperature and light distribution. Site-specific weather and irradiation data are used for annual yield estimations in six climate zones. Shading and reflections between opposing panels and between panels and the ground are dynamically computed based on the reactor geometry and the position of the sun. The results indicate that thin panels (≤0.05 m) are best suited for the assumed cell density of 2 g L -1 and that reactor panels should face in north-south direction. Panel spacings of 0.4-0.75 m at a panel height of 1 m appear most suitable for commercial applications. Under these preconditions, yields of around 10 kg m -2 a -1 are possible for most locations in the U.S. Only in hot climates significantly lower yields have to be expected, as extreme reactor temperatures limit overall productivity.

Microalgae as human food: chemical and nutritional characteristics of the thermo-acidophilic microalga Galdieria sulphuraria.

PubMed

Graziani, Giulia; Schiavo, Simona; Nicolai, Maria Adalgisa; Buono, Silvia; Fogliano, Vincenzo; Pinto, Gabriele; Pollio, Antonino

2013-01-01

The use of microalgae as a food source is still poorly developed because of the technical difficulties related to their cultivation and the limited knowledge about their chemical composition and nutritional value. The unicellular red microalga Galdieria sulphuraria has a very high daily productivity and its cultivation under acidic conditions avoided any bacterial contamination. G. sulphuraria can be cultured under autotrophic and heterotrophic conditions: in this study a screening of 43 strains showed that in the latter case a duplication of biomass production was obtained. The proximate composition (protein, carbohydrates, fiber and lipids), the micronutrient content (carotenoids, phycobiliproteins, chlorophylls and vitamins) together with the antioxidant activity of the biomass produced by a selected strain of G. sulphuraria under both cultivation conditions were determined. Results showed that the material is rich in proteins (26-32%) and polysaccharides (63-69%) and poor in lipids. Under heterotrophic cultivation conditions, the lipid moiety mainly contained monounsaturated fatty acids. Among micronutrients, some B group vitamins are present, beta-carotene is the main carotenoid and phycobiliproteins are present under both cultivating conditions. G. sulphuraria proteins are strictly associated with polysaccharide components and therefore not digestible. In the second part of the work, an extraction protocol using Viscozyme L, a commercial enzymatic preparation containing a mixture of polysaccharidases, was developed which made G. sulphuraria proteins a good substrate for human gastrointestinal enzymes. All in all, the data suggested that G. sulphuraria biomass has a potential use as food ingredients both for protein-rich or insoluble dietary fibre-rich applications. The low concentration of lipids and the absence of green color make this microalgae source particularly useful for the addition to many food preparations.

Microalgal cultivation with biogas slurry for biofuel production.

PubMed

Zhu, Liandong; Yan, Cheng; Li, Zhaohua

2016-11-01

Microalgal growth requires a substantial amount of chemical fertilizers. An alternative to the utilization of fertilizer is to apply biogas slurry produced through anaerobic digestion to cultivate microalgae for the production of biofuels. Plenty of studies have suggested that anaerobic digestate containing high nutrient contents is a potentially feasible nutrient source to culture microalgae. However, current literature indicates a lack of review available regarding microalgal cultivation with biogas slurry for the production of biofuels. To help fill this gap, this review highlights the integration of digestate nutrient management with microalgal production. It first unveils the current status of microalgal production, providing basic background to the topic. Subsequently, microalgal cultivation technologies using biogas slurry are discussed in detail. A scale-up scheme for simultaneous biogas upgrade and digestate application through microalgal cultivation is then proposed. Afterwards, several uncertainties that might affect this practice are explored. Finally, concluding remarks are put forward. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of nitrogen source availability and bioreactor operating strategies on lutein production with Scenedesmus obliquus FSP-3.

PubMed

Ho, Shih-Hsin; Xie, Youping; Chan, Ming-Chang; Liu, Chen-Chun; Chen, Chun-Yen; Lee, Duu-Jong; Huang, Chieh-Chen; Chang, Jo-Shu

2015-05-01

In this study, the effects of the type and concentration of nitrogen sources on the cell growth and lutein content of an isolated microalga Scenedesmus obliquus FSP-3 were investigated. With batch culture, the highest lutein content (4.61 mg/g) and lutein productivity (4.35 mg/L/day) were obtained when using 8.0 mM calcium nitrate as the nitrogen source. With this best nitrogen source condition, the microalgae cultivation was performed using two bioreactor strategies (namely, semi-continuous and two-stage operations) to further enhance the lutein content and productivity. Using semi-continuous operation with a 10% medium replacement ratio could obtain the highest biomass productivity (1304.8 mg/L/day) and lutein productivity (6.01 mg/L/day). This performance is better than most related studies. Copyright © 2014 Elsevier Ltd. All rights reserved.

Process analysis and modeling of a single-step lutein extraction method for wet microalgae.

PubMed

Gong, Mengyue; Wang, Yuruihan; Bassi, Amarjeet

2017-11-01

Lutein is a commercial carotenoid with potential health benefits. Microalgae are alternative sources for the lutein production in comparison to conventional approaches using marigold flowers. In this study, a process analysis of a single-step simultaneous extraction, saponification, and primary purification process for free lutein production from wet microalgae biomass was carried out. The feasibility of binary solvent mixtures for wet biomass extraction was successfully demonstrated, and the extraction kinetics of lutein from chloroplast in microalgae were first evaluated. The effects of types of organic solvent, solvent polarity, cell disruption method, and alkali and solvent usage on lutein yields were examined. A mathematical model based on Fick's second law of diffusion was applied to model the experimental data. The mass transfer coefficients were used to estimate the extraction rates. The extraction rate was found more significantly related with alkali ratio to solvent than to biomass. The best conditions for extraction efficiency were found to be pre-treatment with ultrasonication at 0.5 s working cycle per second, react 0.5 h in 0.27 L/g solvent to biomass ratio, and 1:3 ether/ethanol (v/v) with 1.25 g KOH/L. The entire process can be controlled within 1 h and yield over 8 mg/g lutein, which is more economical for scale-up.

Anaerobic co-digestion of chicken manure and microalgae Chlorella sp.: Methane potential, microbial diversity and synergistic impact evaluation.

PubMed

Li, Ruirui; Duan, Na; Zhang, Yuanhui; Liu, Zhidan; Li, Baoming; Zhang, Dongming; Dong, Taili

2017-10-01

Anaerobic digestion (AD) is a promising alternative for livestock manure management. This paper presents the experimental results obtained through a batch experiment by using chicken manure (CM) and microalgae Chlorella sp. as co-substrates. The effect of co-digestion was evaluated by varying CM to Chlorella sp. ratios (0:10, 2:8, 4:6, 6:4, 8:2, 10: 0 based on the volatile solids (VS)). The major objective of this study is to evaluate the feasibility and synergistic impact of co-digestion of CM and Chlorella sp. Enhanced 14.20% and 76.86% methane production than CM and Chlorella sp. mono-digestion respectively was achieved in co-digestion at the ratio 8:2. In addition, the co-digestion at the ratio 8:2 showed significantly higher methane yield than the weighted average of the individual substrates' specific methane yield (WSMY), indicating strong synergy effect. The Illumina Miseq sequencing analysis showed that the AD process suppressed the acetoclastic methanogenesis Methanosaeta content; but partly enhanced hydrogenotrophic methanogenesis Methanosarcina, Methanospirillum and Methanobacterium, which was responsible for the methane production. The pre-treated microalgae was then introduced at the optimal ratio 8:2 to estimate the effect of pre-treatment of microalgae on AD process. However, the pre-treatment exhibited no positive effect. Copyright © 2017 Elsevier Ltd. All rights reserved.

A validated model to predict microalgae growth in outdoor pond cultures subjected to fluctuating light intensities and water temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huesemann, Michael H.; Crowe, Braden J.; Waller, Peter

Here, a microalgae biomass growth model was developed for screening novel strains for their potential to exhibit high biomass productivities under nutrient-replete conditions in outdoor ponds subjected to fluctuating light intensities and water temperatures. Growth is modeled by first estimating the light attenuation by biomass according to a scatter-corrected Beer-Lambert Law, and then calculating the specific growth rate in discretized culture volume slices that receive declining light intensities due to attenuation. The model requires the following experimentally determined strain-specific input parameters: specific growth rate as a function of light intensity and temperature, biomass loss rate in the dark as amore » function of temperature and average light intensity during the preceding light period, and the scatter-corrected biomass light absorption coefficient. The model was successful in predicting the growth performance and biomass productivity of three different microalgae species (Chlorella sorokiniana, Nannochloropsis salina, and Picochlorum sp.) in raceway pond cultures (batch and semi-continuous) subjected to diurnal sunlight intensity and water temperature variations. Model predictions were moderately sensitive to minor deviations in input parameters. To increase the predictive power of this and other microalgae biomass growth models, a better understanding of the effects of mixing-induced rapid light dark cycles on photo-inhibition and short-term biomass losses due to dark respiration in the aphotic zone of the pond is needed.« less

Evaluation on Microalgae Biomass for Bioethanol Production

NASA Astrophysics Data System (ADS)

Chng, L. M.; Lee, K. T.; Chan, D. C. J.

2017-06-01

The depletion of energy resources has triggered worldwide concern for alternative sources, especially renewable energy. Microalgae biomass offers the most promising feedstock for renewable energy because of their impressive efficient growing characteristics and valuable composition. Simple cell structure of the microalgae would simplify the pretreatment technology thus increase the cost-effectiveness of biofuel production. Scenedesmus dimorphus is a carbohydrate-rich microalgae that has potential as biomass for bioethanol. The cultivation of Scenedesmus dimorphus under aeration of carbon dioxide enriched air resulted 1.47 g/L of dry biomass with composition of 12 w/w total lipid, 53.7 w/w carbohydrate and 17.4 protein. Prior to ethanolic fermentation with Saccharomyces cerevisiae, various pre-treatment methods were investigated to release and degrade the complex carbohydrate in cell biomass thus obtaining the maximal amount of digestible sugar for ethanolic yeast. In this study, sulfuric acid was used as hydrolysis agent while amyloglucosidase as enzymatic agent. Dried biomass via hydrothermal acidic hydrolysis yielded sugar which is about 89 of total carbohydrate at reaction temperature of 125 °C and acid concentration of 4 v/v. While combination of organosolv treatment (mixture of methanol and chloroform) with enzymatic hydrolysis yielded comparable amount of sugar with 0.568 g glucose/g treated-biomass. In this study, the significant information in pre-treatment process ensures the sustainability of the biofuel produced.

A validated model to predict microalgae growth in outdoor pond cultures subjected to fluctuating light intensities and water temperatures

DOE PAGES

Huesemann, Michael H.; Crowe, Braden J.; Waller, Peter; ...

2015-12-11

Here, a microalgae biomass growth model was developed for screening novel strains for their potential to exhibit high biomass productivities under nutrient-replete conditions in outdoor ponds subjected to fluctuating light intensities and water temperatures. Growth is modeled by first estimating the light attenuation by biomass according to a scatter-corrected Beer-Lambert Law, and then calculating the specific growth rate in discretized culture volume slices that receive declining light intensities due to attenuation. The model requires the following experimentally determined strain-specific input parameters: specific growth rate as a function of light intensity and temperature, biomass loss rate in the dark as amore » function of temperature and average light intensity during the preceding light period, and the scatter-corrected biomass light absorption coefficient. The model was successful in predicting the growth performance and biomass productivity of three different microalgae species (Chlorella sorokiniana, Nannochloropsis salina, and Picochlorum sp.) in raceway pond cultures (batch and semi-continuous) subjected to diurnal sunlight intensity and water temperature variations. Model predictions were moderately sensitive to minor deviations in input parameters. To increase the predictive power of this and other microalgae biomass growth models, a better understanding of the effects of mixing-induced rapid light dark cycles on photo-inhibition and short-term biomass losses due to dark respiration in the aphotic zone of the pond is needed.« less

Methods of downstream processing for the production of biodiesel from microalgae.

PubMed

Kim, Jungmin; Yoo, Gursong; Lee, Hansol; Lim, Juntaek; Kim, Kyochan; Kim, Chul Woong; Park, Min S; Yang, Ji-Won

2013-11-01

Despite receiving increasing attention during the last few decades, the production of microalgal biofuels is not yet sufficiently cost-effective to compete with that of petroleum-based conventional fuels. Among the steps required for the production of microalgal biofuels, the harvest of the microalgal biomass and the extraction of lipids from microalgae are two of the most expensive. In this review article, we surveyed a substantial amount of previous work in microalgal harvesting and lipid extraction to highlight recent progress in these areas. We also discuss new developments in the biodiesel conversion technology due to the importance of the connectivity of this step with the lipid extraction process. Furthermore, we propose possible future directions for technological or process improvements that will directly affect the final production costs of microalgal biomass-based biofuels. Copyright © 2013 Elsevier Inc. All rights reserved.

Genetic engineering of the Calvin cycle toward enhanced photosynthetic CO2 fixation in microalgae.

PubMed

Yang, Bo; Liu, Jin; Ma, Xiaonian; Guo, Bingbing; Liu, Bin; Wu, Tao; Jiang, Yue; Chen, Feng

2017-01-01

Photosynthetic microalgae are emerging as potential biomass feedstock for sustainable production of biofuels and value-added bioproducts. CO 2 biomitigation through these organisms is considered as an eco-friendly and promising alternative to the existing carbon sequestration methods. Nonetheless, the inherent relatively low photosynthetic capacity of microalgae has hampered the practical use of this strategy for CO 2 biomitigation applications. Here, we demonstrate the feasibility of improving photosynthetic capacity by the genetic manipulation of the Calvin cycle in the typical green microalga Chlorella vulgaris . Firstly, we fused a plastid transit peptide to upstream of the enhanced green fluorescent protein (EGFP) and confirmed its expression in the chloroplast of C. vulgaris . Then we introduced the cyanobacterial fructose 1,6-bisphosphate aldolase, guided by the plastid transit peptide, into C. vulgaris chloroplast, leading to enhanced photosynthetic capacity (~ 1.2-fold) and cell growth. Molecular and physiochemical analyses suggested a possible role for aldolase overexpression in promoting the regeneration of ribulose 1,5-bisphosphate in the Calvin cycle and energy transfer in photosystems. Our work represents a proof-of-concept effort to enhance photosynthetic capacity by the engineering of the Calvin cycle in green microalgae. Our work also provides insights into targeted genetic engineering toward algal trait improvement for CO 2 biomitigation uses.

Potential use of duckweed based anaerobic digester effluent as a feed source for heterotrophic growth of micro-algae

NASA Astrophysics Data System (ADS)

Ahmadi, L.; Dupont, R.

2013-12-01

Finding an alternative source of energy for the growing world's demand is a challenging task being considered by many scientists. Various types of renewable energy alternatives are being investigated by researchers around the world. The abundance of duckweed (i.e., Lemna and Wolfia sp.) in wetlands and wastewater lagoons, their rapid growth, and their capacity for nutrient, metal and other contaminant removal from wastewater suggests their potential as an inexpensive source of biomass for biofuel production. Another source of biomass for biofuel and energy production is micro-algae. The large-scale growth of micro-algae can potentially be achieved in a smaller footprint and at a higher rate and lower cost via heterotrophic growth compared to autotrophic growth for specific species that can grow under both conditions. Here we describe two types of research. First, two lab-scale, 5 L anaerobic digesters containing municipal raw wastewater that were set up, maintained and monitored over the course of 6 months using duckweed as the feed source. The pH, salinity, amount of gas production and gas composition were measured on a daily basis. The results from these measurements show that duckweed can be used as a good source of biofuel production in the form of methane gas. The second set of reactors consisted of two 1 L batch fed reactors containing algae (Chlorella vulgaris) grown in the lab environment heterotrophically. The pH and DO were monitored on a daily basis in order to investigate their effect on algae growth. Lipid analysis of the harvested algal biomass was done to investigate the efficiency of harvestable biofuel products. A nutrient solution containing glucose as an energy source was used as the initial feed solution, and the potential substitution of the glucose solution with the organic carbon residue from the duckweed digester effluent was investigated. Methane production, carbon stabilization, and gas composition results from the duckweed fed anaerobic digesters, and the growth and biolipid production of heterotrophic micro-algae fed pure substrate versus residual digester effluent carbon are discussed in detail in this study.

Modeling the transformation of atmospheric CO2 into microalgal biomass.

PubMed

Hasan, Mohammed Fahad; Vogt, Frank

2017-10-23

Marine phytoplankton acts as a considerable sink of atmospheric CO 2 as it sequesters large quantities of this greenhouse gas for biomass production. To assess microalgae's counterbalancing of global warming, the quantities of CO 2 they fix need to be determined. For this task, it is mandatory to understand which environmental and physiological parameters govern this transformation from atmospheric CO 2 to microalgal biomass. However, experimental analyses are challenging as it has been found that the chemical environment has a major impact on the physiological properties of the microalgae cells (diameter typ. 5-20 μm). Moreover, the cells can only chemically interact with their immediate vicinity and thus compound sequestration needs to be studied on a microscopic spatial scale. Due to these reasons, computer simulations are a more promising approach than the experimental studies. Modeling software has been developed that describes the dissolution of atmospheric CO 2 into oceans followed by the formation of HCO 3 - which is then transported to individual microalgae cells. The second portion of this model describes the competition of different cell species for this HCO 3 - , a nutrient, as well as its uptake and utilization for cell production. Two microalgae species, i.e. Dunaliella salina and Nannochloropsis oculata, were cultured individually and in a competition situation under different atmospheric CO 2 conditions. It is shown that this novel model's predictions of biomass production are in very good agreement with the experimental flow cytometry results. After model validation, it has been applied to long-term prediction of phytoplankton generation. These investigations were motivated by the question whether or not cell production slows down as cultures grow. This is of relevance as a reduced cell production rate means that the increase in a culture's CO 2 -sinking capacity slows down as well. One implication resulting from this is that an increase in anthropogenic CO 2 may not be counterbalanced by an increase in phytoplankton production. Modeling studies have found that for several different atmospheric CO 2 levels provided to single-species cultures as well as to species in competing scenarios the cell production rate does slow down over time.

Fungal-assisted algal flocculation: application in wastewater treatment and biofuel production.

PubMed

Muradov, Nazim; Taha, Mohamed; Miranda, Ana F; Wrede, Digby; Kadali, Krishna; Gujar, Amit; Stevenson, Trevor; Ball, Andrew S; Mouradov, Aidyn

2015-01-01

The microalgal-based industries are facing a number of important challenges that in turn affect their economic viability. Arguably the most important of these are associated with the high costs of harvesting and dewatering of the microalgal cells, the costs and sustainability of nutrient supplies and costly methods for large scale oil extraction. Existing harvesting technologies, which can account for up to 50% of the total cost, are not economically feasible because of either requiring too much energy or the addition of chemicals. Fungal-assisted flocculation is currently receiving increased attention because of its high harvesting efficiency. Moreover, some of fungal and microalgal strains are well known for their ability to treat wastewater, generating biomass which represents a renewable and sustainable feedstock for bioenergy production. We screened 33 fungal strains, isolated from compost, straws and soil for their lipid content and flocculation efficiencies against representatives of microalgae commercially used for biodiesel production, namely the heterotrophic freshwater microalgae Chlorella protothecoides and the marine microalgae Tetraselmis suecica. Lipid levels and composition were analyzed in fungal-algal pellets grown on media containing alternative carbon, nitrogen and phosphorus sources from wheat straw and swine wastewater, respectively. The biomass of fungal-algal pellets grown on swine wastewater was used as feedstock for the production of value-added chemicals, biogas, bio-solids and liquid petrochemicals through pyrolysis. Co-cultivation of microalgae and filamentous fungus increased total biomass production, lipid yield and wastewater bioremediation efficiency. Fungal-assisted microalgal flocculation shows significant potential for solving the major challenges facing the commercialization of microalgal biotechnology, namely (i) the efficient and cost-effective harvesting of freshwater and seawater algal strains; (ii) enhancement of total oil production and optimization of its composition; (iii) nutrient supply through recovering of the primary nutrients, nitrogen and phosphates and microelements from wastewater. The biomass generated was thermochemically converted into biogas, bio-solids and a range of liquid petrochemicals including straight-chain C12 to C21 alkanes which can be directly used as a glycerine-free component of biodiesel. Pyrolysis represents an efficient alternative strategy for biofuel production from species with tough cell walls such as fungi and fungal-algal pellets.

Performance, insulin sensitivity, carcass characteristics, and fatty acid profile of beef from steers fed microalgae.

PubMed

Carvalho, J R R; Brennan, K M; Ladeira, M M; Schoonmaker, J P

2018-05-25

Heterotrophic production of microalgae biomass provides a consistent, high quality source of docosahexaenoic acid (DHA; C22:6 n-3) in triglyceride oils that could be used as a ration supplement for feedlot steers to improve nutritional qualities of beef. Sixty Angus × Simmental steers (438 ± 6.4 kg) were allotted to 2 treatments (30 steers each, 6 pens, 5 steers/pen) to determine the effects of ForPLUS (DHA-rich microalgae Aurantiochytrium limacinum; 63.6 % fat; 17.9% DHA; 30 mg/kg Sel-Plex; Alltech Inc.) on performance, insulin sensitivity, LM fatty acid composition, and meat quality. Steers were fed basal diets containing 45% corn, 30% distillers dried grains with solubles, 20% corn silage, and 5% supplement. Basal diets were formulated to contain 16.1% CP and 1.32 Mcal/kg NEg. Treatments were delivered to steers in a ground corn based top-dress (454 g total/steer) and contained no microalgae for control steers or 100 g/steer daily of ForPLUS for microalgae steers. A glucose tolerance test (GTT) was performed 10 d prior to slaughter. Steers were slaughtered when a target pen BW of 621 kg was achieved. Fatty acid oxidation potential was determined by measuring thiobarbituric acid reactive substances (TBARS) on LM samples collected 24 h after slaughter and aged for 48 h or 21 d. Weight and BW gain did not differ during the study (P ≥ 0.13); however, steers fed microalgae remained in the feedlot 7 more d compared to steers fed the control diet (111 vs. 104 d; P = 0.04). Overall DMI decreased (P = 0.002) and G:F increased during the second half of the study (P = 0.04) in steers fed microalgae compared to steers fed the control diet. Steers fed microalgae secreted less insulin (P = 0.01) and took longer to clear glucose (P = 0.01) during a 2 h GTT. Carcass traits did not differ between treatments (P ≥ 0.23). Microalgae had no effect on n-6 content (P = 0.67), but more than doubled the n-3 fatty acid percentage and the n3:n6 ratio of the LM (P < 0.0001). The percentage of n-3 fatty acids C20:5 and C22:6 were increased (P < 0.0001) 4-fold and 6.25-fold, respectively, by microalgae supplementation. Concentration of TBARS did not differ in LM aged for 48 h (P = 0.91); however, when aged for 21 d, steers fed microalgae tended to produce LM with greater TBARS concentration compared to steers fed the control diet (P = 0.08). In conclusion, DHA-rich microalgae decreased DMI of steers, and increased n-3 fatty acids and beef oxidation in steaks aged for 21 d.

Novel Concept for LSS Based on Advanced Microalgal Biotechnologies

NASA Technical Reports Server (NTRS)

Brown, I.; Jones, J. A.; Bayless, D.; Karakis, S.; Karpov, L.; McKay, D. S.

2006-01-01

One of the key issues for successful human space exploration is biomedical life support in hostile space and planetary environments that otherwise cannot sustain life. Bioregenerative life support systems (LSS) are one of the options for atmospheric regeneration. To date, no bioregenerative LSS has shown capability for 100% air regeneration. Nor have these LSS been robust enough to simultaneously provide a regenerable complete food source. In contrast to microalgae, traditional plant approaches, e.g. wheat and lettuce, are lacking essential amino acids, vitamins, and micronutrients. Moreover, the rate of photosynthesis by microalgae significantly exceeds that of high plants. Nevertheless, the employment of microalgae in LSS technology was restricted, until recently, due to high water demands. Also the per person requirement of a 40L volume of microalgae in a photobioreactor, to provide daily O2 production, made an algae-based approach less attractive. By employing a vertically stacked membrane bioreactor, coupled with a solar tracker and photon-delivery system, a lightweight air revitalization system for space based applications, with minimal water requirements, can be developed. Our preliminary estimations suggest that a membrane bioreactor, 8m3 in volume, comprised of 80m2 (twenty 2m x 2m membranes, each spaced 10 cm apart), and a total of 70L of water could produce 2.7 kg of dried microalgal biomass that would supply the energy and essential amino acid requirements, as well as producing sufficient O2 for the daily needs of a 15 member crew. Research on the biochemical content of edible blue-green alga Spirulina (Arthrospira) platensis shows a wide spectrum of stable Spirulina mutants with an enhanced content of amino acids, -carotene, and phycobilliprotein c-phycocyanin. Feeding animals suffering from radiation-induced lesions, c-phycocyanin, extracted from strain 27G, led to a correction in the decrement of dehydrogenase activity and energy-rich phosphate levels, as well as improved antioxidant defense and pyruvate levels, compared to untreated animals. Experimental anemia in rats was corrected by feeding Spirulina platensis strains 198B and 27G, (with an enhanced content of methionine, phycobiliproteins and carotenoids). Spirulina was recently shown by Ananyev et al, 2005, to be an oxygenic organism with the highest level of photosystem II activity (O2 production). We propose therefore to develop a design for membrane-based photoreactors for Lunar and Mars exploration habitat LSS, for the cultivation of genetically modified strains of Spirulina to scrub CO2 and supply astronauts with O2, protein, vitamins, and immunostimulators.

Cultivation of Microalgae Chlorella sp on Fresh Water and Waste Water of Tofu Industry

NASA Astrophysics Data System (ADS)

Widayat; Philia, John; Wibisono, Jessica

2018-02-01

Chlorella sp. is a microalgae that potential for food supplement, pharmaceuticals, animal feed, aqua culture and cosmetics. Chlorella sp. commonly growth in sea water. Indonesia as a producer of tofu generated more liquid waste. Nutrient that contained in the tofu wastewater are very useful for the production of microalgae. Cultivation carried out for 7 days at different percent volume of tofu liquid waste showed that the more volume of tofu liquid waste make them longer process decipherment of polymer compounds in the waste, that's make the growth rate of Chlorella sp. are slowness. Variable of10%V has the fastest growth rate. While, 90% v/v variable has the highest concentration of algae. It shows that Chlorella sp. better to grows in tofu wastewater than seawater.

Synergistic effects of oleaginous yeast Rhodotorula glutinis and microalga Chlorella vulgaris for enhancement of biomass and lipid yields.

PubMed

Zhang, Zhiping; Ji, Hairui; Gong, Guiping; Zhang, Xu; Tan, Tianwei

2014-07-01

The optimal mixed culture model of oleaginous yeast Rhodotorula glutinis and microalga Chlorella vulgaris was confirmed to enhance lipid production. A double system bubble column photo-bioreactor was designed and used for demonstrating the relationship of yeast and alga in mixed culture. The results showed that using the log-phase cultures of yeast and alga as seeds for mixed culture, the improvements of biomass and lipid yields reached 17.3% and 70.9%, respectively, compared with those of monocultures. Growth curves of two species were confirmed in the double system bubble column photo-bioreactor, and the second growth of yeast was observed during 36-48 h of mixed culture. Synergistic effects of two species for cell growth and lipid accumulation were demonstrated on O2/CO2 balance, substance exchange, dissolved oxygen and pH adjustment in mixed culture. This study provided a theoretical basis and culture model for producing lipids by mixed culture in place of monoculture. Copyright © 2014 Elsevier Ltd. All rights reserved.

Lipid and fatty acid composition microalgae Chlorella vulgaris using photobioreactor and open pond

NASA Astrophysics Data System (ADS)

Jay, M. I.; Kawaroe, M.; Effendi, H.

2018-03-01

Microalgae contain lipids and fatty acids that can be the raw materials of biofuel. Previous studies have been known of using cultivation systems to obtain biomass of C. vulgaris which can be extracted to obtain lipid and fatty acid content. The observational step was observed ten days in photobioreactor and open pond for harvesting biomass using NaOH, lipid extraction using hexane and methanol, and fatty acid analysis using Gas Chromatography. Lipid content of microalgae biomass in photobioreactor and open pond was 2.26 ± 0.51% and 3.18 ± 0.80%, respectively. Fatty acid content ranged between 0.7-22.8% and 0.9-22.6% and the dominant fatty acids in both cultivating system was palmitic acid.

Phosphorus and metal removal combined with lipid production by the green microalga Desmodesmus sp.: An integrated approach.

PubMed

Rugnini, L; Costa, G; Congestri, R; Antonaroli, S; Sanità di Toppi, L; Bruno, L

2018-04-01

This work focused on the potential of Desmodesmus sp. to be employed for wastewater bioremediation and biodiesel production. The green microalga was grown in a culture medium with a phosphorus (P) content of 4.55 mg L -1 simulating an industrial effluent; it was also exposed to a bimetal solution of copper (Cu) and nickel (Ni) for 2 days. P removal was between 94 and 100%. After 2 days of exposure to metals, 94% of Cu and 85% of Ni were removed by Desmodesmus sp. Adsorption tests showed that the green microalga was able to remove up to 90% of Cu and 43% of Ni in less than 30 min. The presence of metals decreased the lipid yield, but biodiesel quality from the biomass obtained from metal exposed samples was higher than that grown without metals. This result revealed that this technology could offer a new alternative solution to environmental pollution and carbon-neutral fuel generation. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Use of natural pH variation to increase the flocculation of the marine microalgae Nannochloropsis oculata.

PubMed

Sales, Rafael; Abreu, Paulo Cesar

2015-02-01

Microalgae is largely used in aquaculture as feed. More recently, these microorganisms have been considered as an important feedstock for biodiesel production. However, the concentration of produced biomass represents a large parcel of production costs. In this study, we have evaluated the influence of natural pH variation of culture medium, caused by photosynthetic activity, on the flocculation of the marine microalgae Nannochloropsis oculata. Experiments were conducted with the same culture with different pH values (8.5 and 9.6), obtained after exposing the cells to different light conditions. For each pH value, different treatments were composed by adding 0, 5, 10, and 30 mM of NaOH and the flocculant Flopam® (FO4800 SH) at concentrations of 0, 0.5, 1, and 5 ppm. Higher flocculation efficiencies were obtained for the culture with pH 9.6 in comparison to 8.5 for the same NaOH and Flopam concentrations. Lower concentrations of base and flocculant were needed for flocculating the culture in higher pH, representing an economy of 20 % in the costs of crop harvesting.

Evaluation of operating conditions for sustainable harvesting of microalgal biomass applying electrochemical method using non sacrificial electrodes.

PubMed

Misra, Rohit; Guldhe, Abhishek; Singh, Poonam; Rawat, Ismail; Stenström, Thor Axel; Bux, Faizal

2015-01-01

The efficient harvesting of microalgae is considered to be one of the challenging steps of algal biofuel production and a key factor limiting the commercial use of microalgae. To overcome the limitation of metallic electrodes depletion, the application of non-sacrificial electrode was investigated for the electrochemical harvesting (ECH) of microalgae. The effect of applied current, addition of electrolyte and initial pH were parameters investigated. The highest recovery efficiency of 83% was obtained for Scenedesmus obliquus at 1.5A, initial pH 9 and 6gL(-)(1) NaCl with power consumption of 3.84kWhkg(-)(1). Recovery efficiency of ECH process was comparable to literature reported centrifugation, filtration and chemical flocculation techniques but with a much lower power consumption. The ECH process with addition of electrolyte enhanced the lipid extraction by 22% without any adverse effects. The ECH process with non sacrificial carbon electrodes could be a possible harvesting step at commercial scale microalgal biomass production. Copyright © 2014 Elsevier Ltd. All rights reserved.