Microform-related community patterns of methane-cycling microbes in boreal Sphagnum bogs are site specific.

PubMed

Juottonen, Heli; Kotiaho, Mirkka; Robinson, Devin; Merilä, Päivi; Fritze, Hannu; Tuittila, Eeva-Stiina

2015-09-01

Vegetation and water table are important regulators of methane emission in peatlands. Microform variation encompasses these factors in small-scale topographic gradients of dry hummocks, intermediate lawns and wet hollows. We examined methane production and oxidization among microforms in four boreal bogs that showed more variation of vegetation within a bog with microform than between the bogs. Potential methane production was low and differed among bogs but not consistently with microform. Methane oxidation followed water table position with microform, showing higher rates closer to surface in lawns and hollows than in hummocks. Methanogen community, analysed by mcrA terminal restriction fragment length polymorphism and dominated by Methanoregulaceae or 'Methanoflorentaceae', varied strongly with bog. The extent of microform-related variation of methanogens depended on the bog. Methanotrophs identified as Methylocystis spp. in pmoA denaturing gradient gel electrophoresis similarly showed effect of bog, and microform patterns were stronger within individual bogs. Our results suggest that methane-cycling microbes in boreal Sphagnum bogs with seemingly uniform environmental conditions may show strong site-dependent variation. The bog-intrinsic factor may be related to carbon availability but contrary to expectations appears to be unrelated to current surface vegetation, calling attention to the origin of carbon substrates for microbes in bogs. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

36 CFR 1238.22 - What are the inspection requirements for permanent and unscheduled microform records?

Code of Federal Regulations, 2010 CFR

2010-07-01

... the microforms; (iv) A summary of any defects discovered, e.g., redox blemishes or base deformation... microform is deteriorating, the agency must make a silver duplicate in accordance with § 1238.14 to replace...

36 CFR 1238.22 - What are the inspection requirements for permanent and unscheduled microform records?

Code of Federal Regulations, 2011 CFR

2011-07-01

... the microforms; (iv) A summary of any defects discovered, e.g., redox blemishes or base deformation... microform is deteriorating, the agency must make a silver duplicate in accordance with § 1238.14 to replace...

Microform Resources on the Internet Project.

ERIC Educational Resources Information Center

Eichhorn, Sara J.; Yonezawa, Michael

1998-01-01

Summarizes information that will be used to describe microform sets on the University of California, Irvine's World Wide Web site for microform resources, including title, publisher, price, contents, index/bibliography, reviewed in, location/holdings, and Webpac site. Discusses staff/network resources, HTML/UNIX editors, and indexing/search…

Microforms in Libraries; A Reader.

ERIC Educational Resources Information Center

Diaz, Albert James, Ed.

A collection of recent articles on microforms has been compiled to give students and practicing librarians a basic understanding of all aspects of micropublishing as it applies to libraries, with emphasis on library usage rather than microform technology, on the practical rather than the theoretical, on the present rather than the past. Six major…

Five Decades of Microforms at the Library of Congress.

ERIC Educational Resources Information Center

Sullivan, Robert C.

1988-01-01

Discusses the history of the microform collections at the Library of Congress (LC), highlighting the exchange of microfilmed newspapers between LC and the Biblioteca Nacional, Brazil. Recent developments in preservation microfilming, LC's acquisition of microforms, and the activities of the LC Preservation Microfilming Office are described. (3…

Practical Microform Materials for Libraries: Silver, Diazo, Vesicular.

ERIC Educational Resources Information Center

Veaner, Allen B.

1982-01-01

Remarks on the relative permanence and durability of three types of film in use in library microform reproduction (silver, diazo, and vesicular) and points out some technical and economic facts that govern the choice of microform materials for libraries. A 6-item reference list is included. (Author/JL)

Computer Output Microform Library Catalog: A Survey.

ERIC Educational Resources Information Center

Zink, Steven D.

This discussion of the use of computer output microform (COM) as a feasible alternative to the library card catalog includes a brief history of library catalogs and of microform technology since World War II. It is argued that COM catalogs are to be preferred to card catalogs, online catalogs accessed by terminals, and paper printouts. Advantages…

Microform Catalogs: A Viable Alternative for Texas Libraries.

ERIC Educational Resources Information Center

Cox, Carolyn, M.; Juergens, Bonnie

This project proposed to develop and test the use of microform catalogs produced from computer-generated magnetic tape records in both fiche and film formats. The Computer Output Microform (COM) catalog developed for this purpose is a union list of titles from the five participating libraries--Houston and Dallas Public Libraries, Texas State…

Studying All Those "Tiny Little Tea Leaves": The Future of Microforms in a Complex Technological Environment.

ERIC Educational Resources Information Center

Yerburgh, Mark R.

1987-01-01

Considers the future of microforms by surveying the history of their use in libraries; reviewing the literature about them; and comparing them with electronic databases, full text delivery, and laser disks. It is concluded that microforms will continue to be the primary providers of significant but rarely used retrospective materials. (EM)

Microform Film Stock: A Hobson's Choice. Are Librarians Getting the Worst of Both Worlds? (and) Microfilm Types: There Really Is a Choice.

ERIC Educational Resources Information Center

Dupont, Jerry; Dodson, Suzanne Cates

1986-01-01

Two articles summarize qualities of medium being used in production of microforms: silver halide film, diazo film, and vesicular film. Highlights include policy of Law Library Microform Consortium, a nonprofit library cooperative and major supplier of legal materials on microfiche; archival storage and preservation; and recent recommendations.…

Current Developments in Colour Microform Technology.

ERIC Educational Resources Information Center

Gunn, Michael J.

1985-01-01

Addresses some lingering problems with production and use of color microforms, e.g., reliable microfilm emulsion, color temperature, and image fading; and reports on recent advances in color stability and accuracy and international efforts to standardize production. (MBR)

The Dag Hammarskjold Library and United Nations Microforms.

ERIC Educational Resources Information Center

Marulli-Koenig, Luciana

1980-01-01

Surveys the United Nations microform program's history, its current filming projects, and its future plans. Established originally to preserve UN documents for archival purposes, it has expanded to public distribution and dissemination of significant UN documents. (Author)

36 CFR 1238.20 - How must microform records be stored?

Code of Federal Regulations, 2010 CFR

2010-07-01

... relative humidity of the storage area must be a constant 35 percent RH, plus or minus 5 percent. Non-silver copies of microforms must be maintained in a different storage area than are silver gelatin originals or...

Microform Reader Maintenance.

ERIC Educational Resources Information Center

Hall, Hal W.; Michaels, George H.

1985-01-01

Describes experiences in organizing a program of microform reader and reader/printer maintenance at Texas A & M's Sterling C. Evans Library and offers guidelines for regular machine maintenance and repair. Guidelines discussed relate to maintenance philosophy, general machine cleaning, troubleshooting, service contracts, supplies,…

The GPO Reduced to Size: Microforms and Government Publications.

ERIC Educational Resources Information Center

Zink, Steven D.

1983-01-01

Identifies format-specific problems which depository and other government publications librarians frequently face as a result of the Government Printing Office's (GPO) micropublishing program. Program preparation and underpinnings, GPO microform storage in libraries, government publications librarians, and the independence of documents collections…

Micrographics: A Bibliography of Sources.

ERIC Educational Resources Information Center

Thornberry, Patricia Lee; Michael, James D.

This extensive micrographics bibliography, which includes citations drawn from a literature search and prepared bibliographies, covers microforms, microfiche, and microfilm. Sections include 3 pages of book citations, 6 pages citing ERIC documents, and 33 pages of journal citations. Topics covered include microform library usage and usage in other…

Sabbatical Report: Results of a Survey of Library Microforms Facilities.

ERIC Educational Resources Information Center

McIntosh, Melinda C.

1987-01-01

Highlights findings on the status of academic library microforms facilities in the United States and Canada based on visits to 11 libraries. Topics covered include administration, personnel, collection access and storage, classification, acquisition, circulation, indexes, hours, facilities, signage, equipment, photocopying, cleanliness, vandalism,…

Unilateral microform cleft lip repair: application of muscle tension line group theory.

PubMed

Yin, Ningbei; Song, Tao; Wu, Jiajun; Chen, Bo; Ma, Hengyuan; Zhao, Zhenmin; Wang, Yongqian; Li, Haidong; Wu, Di

2015-03-01

In microform cleft lip repair, reconstructing the elaborate structures is difficult. We describe a new technique of unilateral microform cleft lip repair that is based on the muscle tension line group theory. According to the shape of Cupid bow, a different small incision is used without creating an obvious cutaneous scar. First, the nasolabial muscle around the nasal floor (the first auxiliary tension line group) is reconstructed, and then the orbicularis oris muscle around the philtrum (the second auxiliary tension line group) is reconstructed based on the muscle tension line group theory. From June 2006 to June 2012, the technique was used in 263 unilateral microform cleft lip repairs. For 18 months, 212 patients were followed up. The appearance of the nasal alar, nasal sill, philtrum, and Cupid bow peak improved. Most patients had a satisfactory appearance. Based on the muscle tension line group theory, using this technique offers the ability to adduct the nasal alar effectively to form a good nasal sill and philtrum.

Research Sources and Microforms in Black Studies: An Annotated Bibliography.

ERIC Educational Resources Information Center

Ridinger, Robert B. Marks

1985-01-01

Analyzes 93 reference works and 23 microform collections concerning the Black American experience in 13 subject areas of the social sciences (anthropology, biography, race relations and civil rights, the Black church, communication studies, economics, education, dance, genealogy, Black history, sports, women's studies, and literature and language)…

Landmarks of Science: Microforms Cataloging Project, September 1981-December 1983.

ERIC Educational Resources Information Center

Van Orden, Richard

To improve bibliographic access to the individual works contained in "Landmarks of Science" and "Landmarks II," two comprehensive microform collections of materials related to the history of science, the staff of the University of Utah Libraries cataloged the individual titles. Staff members with backgrounds in Renaissance…

Guide to Microforms in Print: 1971.

ERIC Educational Resources Information Center

Diaz, A. J., Ed.

In this annual, cumulative catalog over 19,000 books, journals, newspapers, and multi-volume sets available on microfilm (16mm. and 35mm.), microfiche, or micro-opaque cards from United States publishers are listed in alphabetical order. Only microform publications offered for sale on a regular basis are listed. Books are entered by author. Author…

New Support for the Research Process: Desktop Delivery of Microform Content

ERIC Educational Resources Information Center

Weare, William H., Jr.

2011-01-01

While trying to access microform content, patrons at the Christopher Center for Library and Information Resources at Valparaiso University were often hampered by unfamiliar equipment, temperamental software, and a puzzling file management system. In an effort to address these problems, the Access Services Department launched a pilot program for…

1970 Supplement to the Guide to Microreproduction Equipment.

ERIC Educational Resources Information Center

Ballou, Hubbard W., Ed.

The time period covered by this guide runs from the end of 1968 to the middle of 1970. Microreproduction cameras, microform readers, reader/printers, processors, contact printers, computer output microfilm equipment, and other special microform equipment and accessories produced during this time span are listed. Most of the equipment is domestic,…

Facsimile Transmission of Microforms.

DTIC Science & Technology

1983-12-30

display terminals, high speed printers, conventional facsimile receivers, and/or graphics COM recorders. Microforms designed for storage, retrieval...author and Whould not be construed as an official Department of the Army position, policy, or decision, unless so designated by other documentation...beconstrued as an official Department of the Army position, policy, or decision, unless so designated by other documentation. ,, -- UNCLASSIFIED SECURITY

Wildfire effects on vadose zone hydrology in forested boreal peatland microforms

NASA Astrophysics Data System (ADS)

Thompson, Dan K.; Waddington, James M.

2013-04-01

SummaryPeatland vulnerability to wildfire disturbance has been shown to vary as a function of hummock and hollow microforms and vadose zone hydrology, with low-lying hollow microforms most susceptible to deep combustion of peat. To better understand how this microform induced pattern of burning alters vadose water storage, pore-water pressure, and water table relationships, we examined a paired burned and unburned peatland in the boreal plain region of north central Alberta. Water table response to rain events increased significantly after wildfire, resulting in a more variable unsaturated zone thickness that was more responsive to smaller rain events. Water storage losses in the vadose zone occurred primarily at depths greater than 15 cm. Large peat surface water loss occurred in hummock microforms in the early spring due to the presence of unsaturated frozen peat at depth, likely a result of a vapour gradient from the unfrozen peat into the frozen peat underneath. During this period, the loss of water storage in the vadose zone satisfied up to 25% of daily evaporative demand, compared to only 3-5% during ice-free periods. A similar but less severe drying was observed late in summer, with burned hummocks the most vulnerable with high pore-water pressures. The enhanced surface drying observed is a precursor to high pore-water pressure conditions that inhibit Sphagnum regeneration. Our observations point to a paradox where the hummocks, being most resistant to combustion, are themselves most prone to high pore-water pressures following wildfire. The harsher hummock environment may contribute to the observed delay in post-fire Sphagnum regeneration in hummocks compared to hollows.

Counting Microfiche: The Utilization of the Microform Section of the ANSI Standard Z39.7-1983 "Library Statistics"; Microfiche Curl; and "Poly" or "Cell"?

ERIC Educational Resources Information Center

Caldwell-Wood, Naomi; And Others

1987-01-01

The first of three articles describes procedures for using ANSI statistical methods for estimating the number of pieces in large homogeneous collections of microfiche. The second discusses causes of curl, its control, and measurement, and the third compares the advantages and disadvantages of cellulose acetate and polyester base for microforms.…

Learning COMCAT (Computer Output Microform Catalog): Library Training Program for Foreign Students at New York Institute of Technology.

ERIC Educational Resources Information Center

Chiang, Ching-hsin

This thesis reports on the designer's plans and experiences in carrying out the design, development, implementation, and evaluation of a project, the purpose of which was to develop a training program that would enable foreign students at the New York Institute of Technology (NYIT) to use the Computer Output Microform Catalog (COMCAT) and to…

A Research Project to Determine the Student Acceptability and Learning Effectiveness of Microform Collections in Community Junior Colleges: Phase II. Final Report.

ERIC Educational Resources Information Center

Gaddy, Dale

Five pilot studies were conducted at four two-year colleges in the Washington, D.C. area during the 1970-71 academic year to identify relevant variables for subsequent in-depth examination in this USOE-funded research project which is designed to determine student acceptance and learning effectiveness of microform. Known as Phase II, the year's…

Procedures and Guidelines for Digitization (Scanning)

EPA Pesticide Factsheets

These documents establishes EPA's approach for creating digitized versions of Agency documents and establishes standards for capturing digitized content from paper and microform Agency documents and records.

Reaching for the Stars, Goals for the Library Profession

ERIC Educational Resources Information Center

Bloomfield, Masse

1971-01-01

Space colonization will require the microforming of all of man's worded knowledge which will take leadership and dedication for the library profession information service or documentation. (2 references) (AB)

Computer-Based Indexing on a Small Scale: Bibliography.

ERIC Educational Resources Information Center

Douglas, Kimberly; Wismer, Don

The 131 references on small scale computer-based indexing cited in this bibliography are subdivided as follows: general, general (computer), index structure, microforms, specific systems, KWIC KWAC KWOC, and thesauri. (RAA)

Reprint Characteristics of Non-Silver Films.

ERIC Educational Resources Information Center

Microform Review, 1990

1990-01-01

Describes reprint characteristics of diazo and vesicular films. Use with microform reader-printers and autogeneration of copies are discussed, and methods of dealing with the unusual reprint behavior of these films are outlined. (MES)

36 CFR 1234.14 - What are the requirements for environmental controls for records storage facilities?

Code of Federal Regulations, 2010 CFR

2010-07-01

... temporary records, including microforms and audiovisual and electronic records, must be stored in records..., unscheduled, and/or sample/select records. All records storage facilities that store microfilm, audiovisual...

36 CFR 1238.5 - What publications are incorporated by reference in this part?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Stored Silver-Gelatin Microforms for Evidence of Deterioration, January 22, 1990, IBR approved for § 1238... Materials—Processed silver-gelatin type black-and-white films—Specifications for stability, February 15...

36 CFR 1238.5 - What publications are incorporated by reference in this part?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Stored Silver-Gelatin Microforms for Evidence of Deterioration, January 22, 1990, IBR approved for § 1238... Materials—Processed silver-gelatin type black-and-white films—Specifications for stability, February 15...

36 CFR 1238.5 - What publications are incorporated by reference in this part?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Stored Silver-Gelatin Microforms for Evidence of Deterioration, January 22, 1990, IBR approved for § 1238... Materials—Processed silver-gelatin type black-and-white films—Specifications for stability, February 15...

State and Local Government Publications.

ERIC Educational Resources Information Center

Nakata, Yuri; Kopec, Karen

1980-01-01

Reviews trends in library programs for state and local government publications and documents the increased interest in microforms and databases. Discussion focuses on publication distribution and control, and efforts to support interstate networking. There are 28 references. (RAA)

Accessing the Microform Publication.

ERIC Educational Resources Information Center

Schindler, Stan

1985-01-01

Characterizes types of indexing programs used by Research Publications, Inc. and describes provision of access to four major projects: "The Official Washington Post Index" (provides access to newspaper and microfilm edition); "The Eighteenth Century"; "The Declassified Documents Reference System" (ongoing fiche…

36 CFR § 1238.5 - What publications are incorporated by reference in this part?

Code of Federal Regulations, 2013 CFR

2013-07-01

...”), Recommended Practice for Inspection of Stored Silver-Gelatin Microforms for Evidence of Deterioration, January... 18901:2002 (“ISO 18901”), Imaging Materials—Processed silver-gelatin type black-and-white films...

Laser shock microforming of aluminum foil with fs laser

NASA Astrophysics Data System (ADS)

Ye, Yunxia; Feng, Yayun; Xuan, Ting; Hua, Xijun; Hua, Yinqun

2014-12-01

Laser shock microforming of Aluminum(Al) foil through fs laser has been researched in this paper. The influences of confining layer, clamping method and impact times on induced dent depths were investigated experimentally. Microstructure of fs laser shock forming Al foil was observed through Transmission electron microscopy (TEM). Under the condition of tightly clamping, the dent depths increase with impact times and finally tend to saturating. Another new confining layer, the main component of which is polypropylene, was applied and the confining effect of it is better because of its higher impedance. TEM results show that dislocation is one of the main deformation mechanisms of fs laser shock forming Al foil. Specially, most of dislocations exist in the form of short and discrete dislocation lines. Parallel straight dislocation slip line also were observed. We analyzed that these unique dislocation arrangements are due to fs laser-induced ultra high strain rate.

THE IMPACT OF TECHNOLOGY ON THE LIBRARY BUILDING.

ERIC Educational Resources Information Center

Educational Facilities Labs., Inc., New York, NY.

LIBRARY PLANNERS SHOULD EXPECT AUTOMATION, MICROFORMS, AND FACSIMILE TRANSMISSION TO MODIFY BUT NOT RADICALLY CHANGE THE LIBRARY AS THE INSTITUTION WE NOW KNOW IT TO BE. CHANGES WILL INVOLVE TRADE-OFFS IN SPACE AND DEMANDS FOR ADDITIONAL SPACE. (MF)

36 CFR 1238.20 - How must microform records be stored?

Code of Federal Regulations, 2011 CFR

2011-07-01

... specified in ISO 18911 and ANSI/PIMA IT9.2 (both incorporated by reference, see § 1238.5), except that the... may consult Life Expectance (LE) guidelines in ISO 18901 (incorporated by reference, see § 1238.5). ...

36 CFR 1238.16 - What are the microfilming requirements for temporary records, duplicates, and user copies?

Code of Federal Regulations, 2014 CFR

2014-07-01

... noted in § 1238.3, and manufacturer's instructions for processing production, and maintenance of microform to ensure that the images are accessible and usable for the entire retention period of the records. ...

36 CFR 1238.16 - What are the microfilming requirements for temporary records, duplicates, and user copies?

Code of Federal Regulations, 2012 CFR

2012-07-01

... noted in § 1238.3, and manufacturer's instructions for processing production, and maintenance of microform to ensure that the images are accessible and usable for the entire retention period of the records. ...

36 CFR 1238.16 - What are the microfilming requirements for temporary records, duplicates, and user copies?

Code of Federal Regulations, 2011 CFR

2011-07-01

... noted in § 1238.3, and manufacturer's instructions for processing production, and maintenance of microform to ensure that the images are accessible and usable for the entire retention period of the records. ...

36 CFR 1238.16 - What are the microfilming requirements for temporary records, duplicates, and user copies?

Code of Federal Regulations, 2010 CFR

2010-07-01

... noted in § 1238.3, and manufacturer's instructions for processing production, and maintenance of microform to ensure that the images are accessible and usable for the entire retention period of the records. ...

Optical Digital Disk Storage: An Application for News Libraries.

ERIC Educational Resources Information Center

Crowley, Mary Jo

1988-01-01

Describes the technology, equipment, and procedures necessary for converting a historical newspaper clipping collection to optical disk storage. Alternative storage systems--microforms, laser scanners, optical storage--are also retrieved, and the advantages and disadvantages of optical storage are considered. (MES)

Information Delivery Options over Three Decades.

ERIC Educational Resources Information Center

Kennedy, H. E.

1986-01-01

Reviews the development of technological innovations in information delivery, including microforms, electronic processing, online distribution, full-text abstracts online, floppy disks, downloading, vertical integration, electronic publishing, and optical disks. The impact of technology on the information industry and the need to use technology…

A Guide to the Microform Collections of the USMA Library.

DTIC Science & Technology

1980-01-01

the Renaissance and the Elizabethian period. One may find the earliest editions of Chaucer, Spenser, Shakespeare , More, Erasumus, and Bacon. Military...laws. As a companion to its indexing and abstracting services, CIS provides a comprehensive collection of contemporary government documents on

36 CFR § 1238.16 - What are the microfilming requirements for temporary records, duplicates, and user copies?

Code of Federal Regulations, 2013 CFR

2013-07-01

... noted in § 1238.3, and manufacturer's instructions for processing production, and maintenance of microform to ensure that the images are accessible and usable for the entire retention period of the records. ...

36 CFR 902.82 - Fee schedule.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operating duplicating machinery. Not included in direct costs are overhead expenses such as costs of space... form of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g... programs of scholarly research. (5) Non-commercial scientific institution means an institution that is not...

36 CFR 902.82 - Fee schedule.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operating duplicating machinery. Not included in direct costs are overhead expenses such as costs of space... form of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g... programs of scholarly research. (5) Non-commercial scientific institution means an institution that is not...

5 CFR 294.102 - General definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false General definitions. 294.102 Section 294.102 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS AVAILABILITY OF... the forms that such copies can take are paper, microform, audiovisual materials, or machine readable...

5 CFR 294.102 - General definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false General definitions. 294.102 Section 294.102 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS AVAILABILITY OF... the forms that such copies can take are paper, microform, audiovisual materials, or machine readable...

36 CFR 1238.28 - What must agencies do when sending permanent microform records to a records storage facility?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 1232 of this chapter and the additional requirements in this section. (b) Package non-silver copies... security classification, if any; (5) The inclusive dates, names, or other data identifying the records to...

36 CFR 1238.28 - What must agencies do when sending permanent microform records to a records storage facility?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 1232 of this chapter and the additional requirements in this section. (b) Package non-silver copies... security classification, if any; (5) The inclusive dates, names, or other data identifying the records to...

76 FR 51128 - Privacy Act of 1974; Systems of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-17

... duty; alternate work schedules, standards of conduct and ethics programs; indebtedness; employee... stored on paper, microform, or in electronic media. Retrievability: By name, social security number, or... maceration. Records in electronic media are electronically erased using accepted techniques. System Manager...

CH4 and CO2 production below two contrasting peatland micro-relief forms: An inhibitor and δ13C study.

PubMed

Krohn, Johannes; Lozanovska, Ivana; Kuzyakov, Yakov; Parvin, Shahnaj; Dorodnikov, Maxim

2017-05-15

Two peatland micro-relief forms (microforms) - hummocks and hollows - differ by their hydrological characteristics (water table level, i.e. oxic-anoxic conditions) and vegetation communities. We studied the CH 4 and CO 2 production potential and the localization of methanogenic pathways in both hummocks and hollows at depths of 15, 50, 100, 150 and 200cm in a laboratory incubation experiment. For this purpose, we measured CH 4 and CO 2 production rates, peat elemental composition, as well as δ 13 C values of gases and solids; the specific inhibitor of methanogenesis BES (2-bromo-ethane sulfonate, 1mM) was aimed to preferentially block the acetoclastic pathway. The cumulative CH 4 production of all depths was almost one fold higher in hollows than in hummocks, with no differences in CO 2 . With depth, CO 2 and CH 4 production decreased, and the relative contribution of the hydrogenotrophic pathway of methanogenesis increased. The highest methanogenic activity among all depths and both microforms was measured at 15cm of hollows (91%) at which the highest relative contribution of acetoclastic vs. hydrogenotrophic pathway (92 and 8%, respectively) was detected. For hummocks, the CH 4 production was the highest at 50cm (82%), where relative contribution of acetoclastic methanogenesis comprised 89%. The addition of 1mM BES was not selective and inhibited both methanogenic pathways in the soil. Thus, BES was less efficient in partitioning the pathways compared with the δ 13 C signature. We conclude that the peat microforms - dry hummocks and wet hollows - play an important role for CH 4 but not for CO 2 production when the effects of living vegetation are excluded. Copyright © 2017 Elsevier B.V. All rights reserved.

The Alternative Press in Microform.

ERIC Educational Resources Information Center

Tsang, Daniel C.

Presented is an analysis of what has been done regarding the preservation of alternative publications in microfilm. The alternative press was defined, for the purposes of this study, as "nonstandard, nonestablishment publications." Two projects undertaken to microfilm such publications, one by the Microphoto Division of Bell and Howell…

Mixed Media: A Roundup of New Microform and Electronic Products.

ERIC Educational Resources Information Center

Carter, Christina E.

1996-01-01

Introduces two microfilm collections, one on the Indian Wars of the 19th century and one on records of the Southern Christian Leadership Conference, and four CD-ROM references focusing on Amnesty International, multicultural America, Latin American studies, and North American Indians. (SLD)

41 CFR 105-60.305-1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... duplicating machinery. Overhead expenses such as costs of space, and heating or lighting the facility where... a FOIA request. Copies can take the form of paper, microform audiovisual materials, or magnetic... which operates a program or programs of scholarly research. (h) The term noncommercial scientific...

41 CFR 105-60.305-1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... duplicating machinery. Overhead expenses such as costs of space, and heating or lighting the facility where... a FOIA request. Copies can take the form of paper, microform audiovisual materials, or magnetic... which operates a program or programs of scholarly research. (h) The term noncommercial scientific...

41 CFR 105-60.305-1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... duplicating machinery. Overhead expenses such as costs of space, and heating or lighting the facility where... a FOIA request. Copies can take the form of paper, microform audiovisual materials, or magnetic... which operates a program or programs of scholarly research. (h) The term noncommercial scientific...

36 CFR § 902.82 - Fee schedule.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operating duplicating machinery. Not included in direct costs are overhead expenses such as costs of space... form of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g... programs of scholarly research. (5) Non-commercial scientific institution means an institution that is not...

41 CFR 105-60.305-1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... duplicating machinery. Overhead expenses such as costs of space, and heating or lighting the facility where... a FOIA request. Copies can take the form of paper, microform audiovisual materials, or magnetic... which operates a program or programs of scholarly research. (h) The term noncommercial scientific...

36 CFR 1120.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operating duplicating machinery. Not included in direct costs are overhead expenses such as costs of space... FOIA request. Such copies can take the form of paper copy, microform, audio-visual materials, or... research. (n) Non-Commercial Scientific Institution refers to an institution that is not operated on a...

36 CFR 1120.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operating duplicating machinery. Not included in direct costs are overhead expenses such as costs of space... FOIA request. Such copies can take the form of paper copy, microform, audio-visual materials, or... research. (n) Non-Commercial Scientific Institution refers to an institution that is not operated on a...

Micro-hydromechanical deep drawing of metal cups with hydraulic pressure effects

NASA Astrophysics Data System (ADS)

Luo, Liang; Jiang, Zhengyi; Wei, Dongbin; Wang, Xiaogang; Zhou, Cunlong; Huang, Qingxue

2018-03-01

Micro-metal products have recently enjoyed high demand. In addition, metal microforming has drawn increasing attention due to its net-forming capability, batch manufacturing potential, high product quality, and relatively low equipment cost. Micro-hydromechanical deep drawing (MHDD), a typical microforming method, has been developed to take advantage of hydraulic force. With reduced dimensions, the hydraulic pressure development changes; accordingly, the lubrication condition changes from the macroscale to the microscale. A Voronoi-based finite element model is proposed in this paper to consider the change in lubrication in MHDD according to open and closed lubricant pocket theory. Simulation results agree with experimental results concerning drawing force. Changes in friction significantly affect the drawing process and the drawn cups. Moreover, defined wrinkle indexes have been shown to have a complex relationship with hydraulic pressure. High hydraulic pressure can increase the maximum drawing ratio (drawn cup height), whereas the surface finish represented by the wear is not linearly dependent on the hydraulic pressure due to the wrinkles.

Multiphoton lithography using a high-repetition rate microchip laser.

PubMed

Ritschdorff, Eric T; Shear, Jason B

2010-10-15

Multiphoton lithography (MPL) provides a means to create prototype, three-dimensional (3D) materials for numerous applications in analysis and cell biology. A major impediment to the broad adoption of MPL in research laboratories is its reliance on high peak-power light sources, a requirement that typically has been met using expensive femtosecond titanium:sapphire lasers. Development of affordable microchip laser sources has the potential to substantially extend the reach of MPL, but previous lasers have provided relatively low pulse repetition rates (low kilohertz range), thereby limiting the rate at which microforms could be produced using this direct-write approach. In this report, we examine the MPL capabilities of a new, high-repetition-rate (36.6 kHz) microchip Nd:YAG laser. We show that this laser enables an approximate 4-fold decrease in fabrication times for protein-based microforms relative to the existing state-of-the-art microchip source and demonstrate its utility for creating complex 3D microarchitectures.

Microfiche Viewing Equipment.

ERIC Educational Resources Information Center

Gordon, Ronald F.

All known microform viewer manufacturers and distributors located in the United States were contacted in the gathering of material for this descriptive directory of microfiche readers and reader/printers. Each of the 47 models selected for inclusion is accompanied by a photograph, order information, and a checklist for these features: fiche…

5 CFR 1303.30 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... included in direct costs are overhead expenses such as costs of space, and heating or lighting the facility... request. Such copies can take the form of paper, microform, audio-visual materials, or electronic records... institution of vocational education, that operates a program or programs of scholarly research. (i) The term...

5 CFR 2502.11 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... included in direct costs are overhead expenses such as costs of space, and heating or lighting the facility... FOIA request. Such copies can take the form of paper copy, microform, audio-visual materials, or... operates a program or programs of scholarly research. (i) The term non-commercial scientific institution...

5 CFR 2502.11 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... included in direct costs are overhead expenses such as costs of space, and heating or lighting the facility... FOIA request. Such copies can take the form of paper copy, microform, audio-visual materials, or... operates a program or programs of scholarly research. (i) The term non-commercial scientific institution...

5 CFR 2502.11 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... included in direct costs are overhead expenses such as costs of space, and heating or lighting the facility... FOIA request. Such copies can take the form of paper copy, microform, audio-visual materials, or... operates a program or programs of scholarly research. (i) The term non-commercial scientific institution...

5 CFR 1303.30 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... included in direct costs are overhead expenses such as costs of space, and heating or lighting the facility... request. Such copies can take the form of paper, microform, audio-visual materials, or electronic records... institution of vocational education, that operates a program or programs of scholarly research. (i) The term...

11 CFR 4.1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... duplicating equipment. Direct costs do not include overhead expenses such as the cost of space and heating or... request. Examples of the form such copies can take include, but are not limited to, paper copy, microform... an institution of vocational education, which operates a program or programs of scholarly research...

15 CFR 4.11 - Fees.

Code of Federal Regulations, 2014 CFR

2014-01-01

... benefits). Not included in direct costs are overhead expenses such as the costs of space, heating, or... the form of paper, microform, audiovisual materials, or electronic records (for example, magnetic tape... scholarly research. To be in this category, a requester must show that the request is authorized by and is...

11 CFR 4.1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... duplicating equipment. Direct costs do not include overhead expenses such as the cost of space and heating or... request. Examples of the form such copies can take include, but are not limited to, paper copy, microform... an institution of vocational education, which operates a program or programs of scholarly research...

5 CFR 1820.7 - Fees.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the costs of space, and heating or lighting the facility in which the records are kept. (3..., necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials... education, or an institution of vocational education, that operates a program of scholarly research. To be...

36 CFR § 1120.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operating duplicating machinery. Not included in direct costs are overhead expenses such as costs of space... FOIA request. Such copies can take the form of paper copy, microform, audio-visual materials, or... research. (n) Non-Commercial Scientific Institution refers to an institution that is not operated on a...

5 CFR 1820.7 - Fees.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the costs of space, and heating or lighting the facility in which the records are kept. (3..., necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials... education, or an institution of vocational education, that operates a program of scholarly research. To be...

15 CFR 4.11 - Fees.

Code of Federal Regulations, 2012 CFR

2012-01-01

... benefits). Not included in direct costs are overhead expenses such as the costs of space, heating, or... the form of paper, microform, audiovisual materials, or electronic records (for example, magnetic tape... scholarly research. To be in this category, a requester must show that the request is authorized by and is...

5 CFR 1820.7 - Fees.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the costs of space, and heating or lighting the facility in which the records are kept. (3..., necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials... education, or an institution of vocational education, that operates a program of scholarly research. To be...

15 CFR 4.11 - Fees.

Code of Federal Regulations, 2013 CFR

2013-01-01

... benefits). Not included in direct costs are overhead expenses such as the costs of space, heating, or... the form of paper, microform, audiovisual materials, or electronic records (for example, magnetic tape... scholarly research. To be in this category, a requester must show that the request is authorized by and is...

5 CFR 1303.30 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... included in direct costs are overhead expenses such as costs of space, and heating or lighting the facility... request. Such copies can take the form of paper, microform, audio-visual materials, or electronic records... institution of vocational education, that operates a program or programs of scholarly research. (i) The term...

11 CFR 4.1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... duplicating equipment. Direct costs do not include overhead expenses such as the cost of space and heating or... request. Examples of the form such copies can take include, but are not limited to, paper copy, microform... an institution of vocational education, which operates a program or programs of scholarly research...

15 CFR 4.11 - Fees.

Code of Federal Regulations, 2011 CFR

2011-01-01

... benefits). Not included in direct costs are overhead expenses such as the costs of space, heating, or... the form of paper, microform, audiovisual materials, or electronic records (for example, magnetic tape... scholarly research. To be in this category, a requester must show that the request is authorized by and is...

11 CFR 4.1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... duplicating equipment. Direct costs do not include overhead expenses such as the cost of space and heating or... request. Examples of the form such copies can take include, but are not limited to, paper copy, microform... an institution of vocational education, which operates a program or programs of scholarly research...

5 CFR 1820.7 - Fees.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the costs of space, and heating or lighting the facility in which the records are kept. (3..., necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials... education, or an institution of vocational education, that operates a program of scholarly research. To be...

Annual Review of Information Science and Technology. Volume Eight.

ERIC Educational Resources Information Center

Cuadra, Carlos A., Ed.; Luke, Ann W., Ed.

Descriptions and appraisals of significant recent trends and developments in the field of information science are presented. The eleven individual chapters deal, respectively, with the following topics: 1) the economics of information, 2) document description and representation, 3) automated language processing, 4) microform technology, 5) library…

10 CFR 2.1001 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... portions that are neither textual nor image in nature, and graphic or other Binary Large Objects that... docket materials. Image means a visual likeness of a document, presented on a paper copy, microform, or a... J of this part, including the authority of the Pre-License Application Presiding Officer designated...

10 CFR 2.1001 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... files having substantial portions that are neither textual nor image in nature, and graphic or other... docket materials. Image means a visual likeness of a document, presented on a paper copy, microform, or a... J of this part, including the authority of the Pre-License Application Presiding Officer designated...

10 CFR 2.1001 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... portions that are neither textual nor image in nature, and graphic or other Binary Large Objects that... docket materials. Image means a visual likeness of a document, presented on a paper copy, microform, or a... J of this part, including the authority of the Pre-License Application Presiding Officer designated...

10 CFR 2.1001 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... files having substantial portions that are neither textual nor image in nature, and graphic or other... docket materials. Image means a visual likeness of a document, presented on a paper copy, microform, or a... J of this part, including the authority of the Pre-License Application Presiding Officer designated...

77 FR 60667 - EPAAR Clause for Printing

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-04

... to illustrate your concerns, and suggest alternatives. Explain your views as clearly as possible... by a color inkjet or color laser printer. This is not considered ``printing.'' However, if the output... include microfiche and microfilm. The contractor may make up to two sets of microform files for archival...

21 CFR 1401.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Definitions. 1401.3 Section 1401.3 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY PUBLIC AVAILABILITY OF INFORMATION § 1401.3 Definitions. For the... paper, microform, audio-visual materials, or machine-readable documentation. ONDCP will provide a copy...

10 CFR 1303.108 - Fees.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the records. Overhead expenses, such as the costs of space, heating, and lighting, are not included.... Copies can be in paper, microform, electronic, or other format. The Board shall honor a requestor's... school, that has a program of scholarly research. For a request to be in this category, a requestor must...

19 CFR 201.20 - Fees.

Code of Federal Regulations, 2012 CFR

2012-04-01

... requesters, subject to the limitations of paragraph (c) of this section. For a paper photocopy of a record... overhead expenses such as costs of space and heating or lighting of the facility in which the records are... of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g., magnetic...

40 CFR 1601.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... overhead expenses, such as the cost of space and heating or lighting of the facility in which the records... FOIA request. Such copies can take the form of, among other things, paper copy, microform, audio-visual... operates a program of scholarly research. FOIA Officer means the person designated to process requests for...

45 CFR 1171.11 - Fees.

Code of Federal Regulations, 2014 CFR

2014-10-01

... such as the costs of space and heating or lighting of the facility in which the records are kept. (3... respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials, or... scholarly research. A requester in this category must show that the request is authorized by and made under...

19 CFR 201.20 - Fees.

Code of Federal Regulations, 2013 CFR

2013-04-01

... requesters, subject to the limitations of paragraph (c) of this section. For a paper photocopy of a record... overhead expenses such as costs of space and heating or lighting of the facility in which the records are... of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g., magnetic...

10 CFR 1303.108 - Fees.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the records. Overhead expenses, such as the costs of space, heating, and lighting, are not included.... Copies can be in paper, microform, electronic, or other format. The Board shall honor a requestor's... school, that has a program of scholarly research. For a request to be in this category, a requestor must...

49 CFR 701.11 - Fees.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of paper, microform, audiovisual materials, or electronic records (i.e., magnetic tape or disk) among... costs do not include overhead expenses such as the costs of space and heating or lighting of the... that operates a program of scholarly research. To be in this category, a requester must show that the...

29 CFR 70.38 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... duplication machinery. Not included in direct costs are overhead expenses such as costs of space, heating or... a record necessary to respond to a request. Such copy can take the form of paper, microform, audio... research. To qualify under this definition, the program of scholarly research in connection with which the...

10 CFR 1303.108 - Fees.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the records. Overhead expenses, such as the costs of space, heating, and lighting, are not included.... Copies can be in paper, microform, electronic, or other format. The Board shall honor a requestor's... school, that has a program of scholarly research. For a request to be in this category, a requestor must...

29 CFR 70.38 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... duplication machinery. Not included in direct costs are overhead expenses such as costs of space, heating or... a record necessary to respond to a request. Such copy can take the form of paper, microform, audio... research. To qualify under this definition, the program of scholarly research in connection with which the...

19 CFR 201.20 - Fees.

Code of Federal Regulations, 2014 CFR

2014-04-01

... requesters, subject to the limitations of paragraph (c) of this section. For a paper photocopy of a record... overhead expenses such as costs of space and heating or lighting of the facility in which the records are... of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g., magnetic...

49 CFR 701.11 - Fees.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of paper, microform, audiovisual materials, or electronic records (i.e., magnetic tape or disk) among... costs do not include overhead expenses such as the costs of space and heating or lighting of the... that operates a program of scholarly research. To be in this category, a requester must show that the...

40 CFR 1601.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... overhead expenses, such as the cost of space and heating or lighting of the facility in which the records... FOIA request. Such copies can take the form of, among other things, paper copy, microform, audio-visual... operates a program of scholarly research. FOIA Officer means the person designated to process requests for...

49 CFR 701.11 - Fees.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of paper, microform, audiovisual materials, or electronic records (i.e., magnetic tape or disk) among... costs do not include overhead expenses such as the costs of space and heating or lighting of the... that operates a program of scholarly research. To be in this category, a requester must show that the...

40 CFR 1601.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... overhead expenses, such as the cost of space and heating or lighting of the facility in which the records... FOIA request. Such copies can take the form of, among other things, paper copy, microform, audio-visual... operates a program of scholarly research. FOIA Officer means the person designated to process requests for...

29 CFR 70.38 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... duplication machinery. Not included in direct costs are overhead expenses such as costs of space, heating or... a record necessary to respond to a request. Such copy can take the form of paper, microform, audio... research. To qualify under this definition, the program of scholarly research in connection with which the...

19 CFR 201.20 - Fees.

Code of Federal Regulations, 2011 CFR

2011-04-01

... requesters, subject to the limitations of paragraph (c) of this section. For a paper photocopy of a record... overhead expenses such as costs of space and heating or lighting of the facility in which the records are... of paper copy, microform, audio-visual materials, or machine-readable documentation (e.g., magnetic...

49 CFR 701.11 - Fees.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of paper, microform, audiovisual materials, or electronic records (i.e., magnetic tape or disk) among... costs do not include overhead expenses such as the costs of space and heating or lighting of the... that operates a program of scholarly research. To be in this category, a requester must show that the...

29 CFR 70.38 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... duplication machinery. Not included in direct costs are overhead expenses such as costs of space, heating or... a record necessary to respond to a request. Such copy can take the form of paper, microform, audio... research. To qualify under this definition, the program of scholarly research in connection with which the...

10 CFR 1303.108 - Fees.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the records. Overhead expenses, such as the costs of space, heating, and lighting, are not included.... Copies can be in paper, microform, electronic, or other format. The Board shall honor a requestor's... school, that has a program of scholarly research. For a request to be in this category, a requestor must...

32 CFR 1662.6 - Fee schedule; waiver of fees.

Code of Federal Regulations, 2012 CFR

2012-07-01

... as costs of space, and heating or lighting the facility in which the records are stored. (2) The term... copies may take the form of paper copy, microform, audio-visual materials, or machine readable... institution of vocational education, which operates a program or programs of scholarly research. (7) The term...

32 CFR 1662.6 - Fee schedule; waiver of fees.

Code of Federal Regulations, 2014 CFR

2014-07-01

... as costs of space, and heating or lighting the facility in which the records are stored. (2) The term... copies may take the form of paper copy, microform, audio-visual materials, or machine readable... institution of vocational education, which operates a program or programs of scholarly research. (7) The term...

40 CFR 1601.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... overhead expenses, such as the cost of space and heating or lighting of the facility in which the records... FOIA request. Such copies can take the form of, among other things, paper copy, microform, audio-visual... operates a program of scholarly research. FOIA Officer means the person designated to process requests for...

Microform Publishing: Salvation for Short-Run Periodicals?

ERIC Educational Resources Information Center

Bovee, Warren G.

Micropublishing, a new technology, has provided small-circulation periodicals, which have little advertising revenues, with an alternative to escalating costs of traditional paper publication. The process of micropublishing which is most serviceable for short-run periodicals involves the use of microfiche--a small piece of film which can contain…

5 CFR 294.102 - General definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the forms that such copies can take are paper, microform, audiovisual materials, or machine readable... that is necessary to excise them and otherwise prepare them for release. Review does not include time... the time spent looking for material that is responsive to a request, including page-by-page or line-by...

Micrographics: A Quarter-Century Perspective.

ERIC Educational Resources Information Center

Ach, William K.

2000-01-01

Discusses the uses of micrographics in higher education, based on a 25-year period at Wake Forest University's (Winston-Salem, North Carolina) Library. Discusses acquisition of scholarly collections in microform on a subscription plan; the trend away from microopaques to microfiche and the advent of the reader-printer; improved access to microform…

National Libraries Section. General Research Libraries Division. Papers.

ERIC Educational Resources Information Center

International Federation of Library Associations, The Hague (Netherlands).

Papers on national library services and activities, which were presented at the 1983 International Federation of Library Associations (IFLA) conference, include: (1) "The National Library of China in its Gradual Application of Modern Technology," a discussion by Zhu Nan and Zhu Yan (China) of microform usage and library automation; (2)…

Basics of Videodisc and Optical Disk Technology.

ERIC Educational Resources Information Center

Paris, Judith

1983-01-01

Outlines basic videodisc and optical disk technology describing both optical and capacitance videodisc technology. Optical disk technology is defined as a mass digital image and data storage device and briefly compared with other information storage media including magnetic tape and microforms. The future of videodisc and optical disk is…

Information Delivery Options over Three Decades.

ERIC Educational Resources Information Center

Kennedy, H. Edward

1986-01-01

The rate of new technology-driven innovations for information delivery has accelerated over the past three decades. New information delivery formats in the 1950s and 1960s included microforms and, in response to demands from librarians, indexing and abstracting services began to make their publications available on this medium. Electronic…

78 FR 22795 - EPAAR Clause for Printing

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-17

.... Therefore, EPA is not considering the use of any voluntary consensus standards. J. Executive Order 12898... devices for the purpose of producing camera copy, negatives, a plate or image to be used in the production... are considered ``printing.'' ``Microform'' is any product produced in a miniaturized image format, for...

Computer Output Microform (COM) Catalog Requirements for the Virginia Commonwealth University Libraries.

ERIC Educational Resources Information Center

White, Robert L.

Generated as the result of the deliberations of the COM Catalog Advisory Work Group, which depended heavily on a review of the available literature, individual analysis, and group discussion, this report is intended as a general planning document for Virginia Commonwealth university libraries concerning their possible implementation of a COM…

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2011 CFR

2011-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR § 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2013 CFR

2013-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2014 CFR

2014-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2012 CFR

2012-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2010 CFR

2010-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

The Use of Microform to Support the Amherst Local History Project.

ERIC Educational Resources Information Center

Lombardo, Daniel

1987-01-01

Describes a local history project designed for ninth-grade students, in which students use primary historical sources to research local history, and the resulting conflict between access to rare documents versus preservation of those materials. The major microfilming project that was undertaken to resolve this conflict is outlined. (CLB)

34 CFR 668.24 - Record retention and examinations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... representative. (3) An institution may keep required records in hard copy or in microform, computer file, optical disk, CD-ROM, or other media formats, provided that— (i) Except for the records described in paragraph (d)(3)(ii) of this section, all record information must be retrievable in a coherent hard copy format...

29 CFR 2201.4 - General policy and definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... such as the costs of space and heating or lighting of the facility in which the records are kept... respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials, or... institution of vocational education, that operates a program of scholarly research. To be in this category, a...

28 CFR 16.11 - Fees.

Code of Federal Regulations, 2012 CFR

2012-07-01

... overhead expenses such as the costs of space and heating or lighting of the facility in which the records... it, necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual... research. To be in this category, a requester must show that the request is authorized by and is made under...

28 CFR 16.11 - Fees.

Code of Federal Regulations, 2011 CFR

2011-07-01

... overhead expenses such as the costs of space and heating or lighting of the facility in which the records... it, necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual... research. To be in this category, a requester must show that the request is authorized by and is made under...

28 CFR 16.11 - Fees.

Code of Federal Regulations, 2013 CFR

2013-07-01

... overhead expenses such as the costs of space and heating or lighting of the facility in which the records... it, necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual... research. To be in this category, a requester must show that the request is authorized by and is made under...

29 CFR 2201.4 - General policy and definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... such as the costs of space and heating or lighting of the facility in which the records are kept... respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials, or... institution of vocational education, that operates a program of scholarly research. To be in this category, a...

28 CFR 16.11 - Fees.

Code of Federal Regulations, 2014 CFR

2014-07-01

... overhead expenses such as the costs of space and heating or lighting of the facility in which the records... it, necessary to respond to a FOIA request. Copies can take the form of paper, microform, audiovisual... research. To be in this category, a requester must show that the request is authorized by and is made under...

29 CFR 2201.4 - General policy and definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... such as the costs of space and heating or lighting of the facility in which the records are kept... respond to a FOIA request. Copies can take the form of paper, microform, audiovisual materials, or... institution of vocational education, that operates a program of scholarly research. To be in this category, a...

Microfiche Storage and Retrieval System Study: Final Report.

ERIC Educational Resources Information Center

Wicker, Roger; And Others

System Development Corporation's (SDC) exploration of microform state-of-the-art and current research reveals developments which will be applicable to the requirements of many small Department of Defense (DoD) users and similar facilities in the next two to five years. The study's survey of the small user population reveals a variety of user…

36 CFR § 1254.108 - What are NARA's requirements for the microfilming process?

Code of Federal Regulations, 2013 CFR

2013-07-01

... you leave unattended. (j) We inspect the microform output at scheduled intervals during the project to... images, you must provide NARA with a silver halide duplicate negative upon completion of the project. When the project involves more than 10,000 images, you must provide a silver halide duplicate negative...

Cataloging the Confederate Imprints, 1861-1865 Major Microfilm Set: Designing a Successful Workflow.

ERIC Educational Resources Information Center

Schmitz, Cecilia M.

1995-01-01

Details the flexible assembly-line approach used by Auburn University to catalog the "Confederate Imprints, 1861-1865" major microform set. Five thousand nine hundred sixty-six (5966) distinct items were cataloged over a 3-year period by one professional, one library assistant and two student workers. (Author/JKP)

36 CFR 1238.1 - What is the scope of this part?

Code of Federal Regulations, 2014 CFR

2014-07-01

... ADMINISTRATION RECORDS MANAGEMENT MICROFORMS RECORDS MANAGEMENT General § 1238.1 What is the scope of this part? This part covers the standards and procedures for using micrographic technology in the management of... 36 Parks, Forests, and Public Property 3 2014-07-01 2014-07-01 false What is the scope of this...

36 CFR 1238.1 - What is the scope of this part?

Code of Federal Regulations, 2012 CFR

2012-07-01

... ADMINISTRATION RECORDS MANAGEMENT MICROFORMS RECORDS MANAGEMENT General § 1238.1 What is the scope of this part? This part covers the standards and procedures for using micrographic technology in the management of... 36 Parks, Forests, and Public Property 3 2012-07-01 2012-07-01 false What is the scope of this...

36 CFR 1238.1 - What is the scope of this part?

Code of Federal Regulations, 2010 CFR

2010-07-01

... ADMINISTRATION RECORDS MANAGEMENT MICROFORMS RECORDS MANAGEMENT General § 1238.1 What is the scope of this part? This part covers the standards and procedures for using micrographic technology in the management of... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false What is the scope of this...

Measurement of material mechanical properties in microforming

NASA Astrophysics Data System (ADS)

Yun, Wang; Xu, Zhenying; Hui, Huang; Zhou, Jianzhong

2006-02-01

As the rapid market need of micro-electro-mechanical systems engineering gives it the wide development and application ranging from mobile phones to medical apparatus, the need of metal micro-parts is increasing gradually. Microforming technology challenges the plastic processing technology. The findings have shown that if the grain size of the specimen remains constant, the flow stress changes with the increasing miniaturization, and also the necking elongation and the uniform elongation etc. It is impossible to get the specimen material properties in conventional tensile test machine, especially in the high precision demand. Therefore, one new measurement method for getting the specimen material-mechanical property with high precision is initiated. With this method, coupled with the high speed of Charge Coupled Device (CCD) camera and high precision of Coordinate Measuring Machine (CMM), the elongation and tensile strain in the gauge length are obtained. The elongation, yield stress and other mechanical properties can be calculated from the relationship between the images and CCD camera movement. This measuring method can be extended into other experiments, such as the alignment of the tool and specimen, micro-drawing process.

Recurrent erosion of the cornea.

PubMed Central

Brown, N.; Bron, A.

1976-01-01

Altogether, 80 patients aged between 24 and 73 years with recurrent erosion of the cornea have been studied and compared with a control group of 200. The patients' erosions were divisible into macroform and microform types. The macroform occurred in 10%, the microform in 56%, and both types in the same patients in 31%. The macroform was more commonly related to trauma than the microform. However, many (40%) were spontaneous in origin. The most common cause of the initial trauma was a finger nail. The recurrences occurred at around the time of waking, either just before or just after. Difficulty in opening the eye occurred in 10%. There was little evidence of precipitating factors, but eye rubbing was admitted by 10% and barbiturates were implicated in 3%. The corneae were examined in the healed state, when a high incidence (59%) were found to have superficial corneal dystrophies of the fingerprint lines, bleb, and Bietti's lacunar (map-like) types. These are considered individually, particular attention being paid to the distinction between the various types of line resembling the fingerprint line. Epithelial microcysts were also a common finding (59%) and were sometimes of the Cogan type. In only 11% of patients were there no corneal signs in the healed state. The need for careful examination of the cornea by retroillumination, using both the iris and the fundus, is stressed. The control group, in contrast, showed a very low incidence of dystrophies and cysts. Treatment was given initially with either drops or ointment and no differences in healing were found. Debridement was performed in 12 eyes as an initial treatment and also in four eyes which were not healing on medical treatment. Debridement assisted healing, but did not prevent recurrence. One eye was treated with debridement and scarification and seven with carbolization. These procedures appeared to reduce the recurrence rate. Sodium chloride ointment 5% was found useful as a prophylactic taken at bedtime, and the recurrence rate increased when it was withdrawn. Images PMID:1083744

North Dakota Academic Library Statistics; July 1973 through June 1974.

ERIC Educational Resources Information Center

North Dakota Library Notes, 1975

1975-01-01

The bulk of this volume is comprised of the statistical report forms submitted to the state library by all of the academic libraries in the state of North Dakota. The data presented for each library includes: print resources (books, documents, serials, and microforms); audiovisual holdings; collection use in terms of in-library usage, circulation,…

Administrative and Bibliographic Uses of COM (Computer Output Microfilm) in an Academic Library.

ERIC Educational Resources Information Center

Gillham, Virginia; Black, John B.

Computer output microfilm/fiche (COM) combines the speed and laborsaving aspects of computer-based systems with the economy and physical compactness of microforms to provide the medium of the future for library management and information retrieval. The traditional card catalog and printed lists found in every library can be replaced in multiple…

Council On Library Resources, Inc. Seventeenth Annual Report, For the Year Ending June 30, 1973.

ERIC Educational Resources Information Center

Council on Library Resources, Inc., Washington, DC.

This report describes the efforts of the Council on Library Resources to enhance the effectiveness, efficiency, and economy of operations in libraries during 1972-73. It covers 9 major areas: national library services, automation and networks, the academic library, the public library, microform and nonprint media, preservation and library…

USER SERVICES AND EXTENSION SERVICES IN SELECTED SPECIAL LIBRARIES AND INFORMATION CENTERS IN THE UNITED STATES.

ERIC Educational Resources Information Center

NONINI, CERISE

A SURVEY BY QUESTIONNAIRE WAS MADE OF THE PROBLEM OF USER SERVICES AND EXTENSION SERVICES USED IN THE DISSEMINATION OF MATERIALS AND INFORMATION TO A SELECTED NUMBER OF INDUSTRIAL LIBRARIES. THE SURVEY RESULTED IN DATA CONCERNING STAFF SIZE, PROFESSIONAL-TO-CLERICAL RATIO, SIZE OF BOOK, DOCUMENT, PERIODICAL AND MICROFORM COLLECTIONS, LIBRARY…

36 CFR 1223.18 - Must vital records be in a particular form or format?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Must vital records be in a particular form or format? 1223.18 Section 1223.18 Parks, Forests, and Public Property NATIONAL ARCHIVES AND..., magnetic tape, optical disk, photographic film, and microform. In selecting the media, agencies must ensure...

36 CFR 1223.18 - Must vital records be in a particular form or format?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Must vital records be in a particular form or format? 1223.18 Section 1223.18 Parks, Forests, and Public Property NATIONAL ARCHIVES AND..., magnetic tape, optical disk, photographic film, and microform. In selecting the media, agencies must ensure...

The Sourcebook of Library Technology. 1994 Edition. A Microform Edition of Library Technology Reports and Library Systems Newsletter 1992 and 1993.

ERIC Educational Resources Information Center

Hori, Pamela, Comp.; White, Howard S., Ed.

This sourcebook is an indexed compilation, on microfiches, of material published during 1992 and 1993 in "Library Technology Reports" (LTR) and "Library Systems Newsletter.""LTR" is a publication by the American Library Association (ALA) which provides critical evaluation of products and systems used in libraries,…

Resource Sharing in Montana: A Study of Interlibrary Loan and Alternatives for a Montana Union Catalog.

ERIC Educational Resources Information Center

Matthews, Joseph R.

This study recommends a variety of actions to create and maintain a Montana union catalog (MONCAT) for more effective usage of in-state resources and library funds. Specifically, it advocates (1) merger of existing COM, machine readable bibliographic records, and OCLC tapes into a single microform catalog; (2) acceptance of only machine readable…

42 CFR 60.42 - Records, reports, inspection, and audit requirements for HEAL lenders and holders.

Code of Federal Regulations, 2013 CFR

2013-10-01

... must maintain for each borrower a payment history showing the date and amount of each payment received... lender or holder must also maintain for each loan a collection history showing the date and subject of... original copy of an unpaid promissory note, but may store all other records in microform or computer format...

42 CFR 60.42 - Records, reports, inspection, and audit requirements for HEAL lenders and holders.

Code of Federal Regulations, 2011 CFR

2011-10-01

... must maintain for each borrower a payment history showing the date and amount of each payment received... lender or holder must also maintain for each loan a collection history showing the date and subject of... original copy of an unpaid promissory note, but may store all other records in microform or computer format...

42 CFR 60.42 - Records, reports, inspection, and audit requirements for HEAL lenders and holders.

Code of Federal Regulations, 2012 CFR

2012-10-01

... must maintain for each borrower a payment history showing the date and amount of each payment received... lender or holder must also maintain for each loan a collection history showing the date and subject of... original copy of an unpaid promissory note, but may store all other records in microform or computer format...

Ultrahigh-resolution mapping of peatland microform using ground-based structure from motion with multiview stereo

NASA Astrophysics Data System (ADS)

Mercer, Jason J.; Westbrook, Cherie J.

2016-11-01

Microform is important in understanding wetland functions and processes. But collecting imagery of and mapping the physical structure of peatlands is often expensive and requires specialized equipment. We assessed the utility of coupling computer vision-based structure from motion with multiview stereo photogrammetry (SfM-MVS) and ground-based photos to map peatland topography. The SfM-MVS technique was tested on an alpine peatland in Banff National Park, Canada, and guidance was provided on minimizing errors. We found that coupling SfM-MVS with ground-based photos taken with a point and shoot camera is a viable and competitive technique for generating ultrahigh-resolution elevations (i.e., <0.01 m, mean absolute error of 0.083 m). In evaluating 100+ viable SfM-MVS data collection and processing scenarios, vegetation was found to considerably influence accuracy. Vegetation class, when accounted for, reduced absolute error by as much as 50%. The logistic flexibility of ground-based SfM-MVS paired with its high resolution, low error, and low cost makes it a research area worth developing as well as a useful addition to the wetland scientists' toolkit.

Library Technology and Architecture; Report of a Conference Held at the Harvard Graduate School of Education, February 9, 1967.

ERIC Educational Resources Information Center

Harvard Univ., Cambridge, MA. Graduate School of Education.

The purpose of the conference was to investigate the implications of new technologies for library architecture and to use the findings in planning new Library Research Facility for the Harvard Graduate School of Education. The first half of this document consists of reports prepared by six consultants on such topics as microforms, computers,…

Information Technology for Agricultural America. Prepared for the Subcommittee on Department Operations, Research and Foreign Agriculture, 97th Congress, 2d Session. Committee Print.

ERIC Educational Resources Information Center

Library of Congress, Washington, DC. Congressional Research Service.

This summary of the combined Hearing and Workshop on Applications of Computer-Based Information Systems and Services in Agriculture (May 19-20, 1982) offers an overview of the ways in which information technology--computers, telecommunications, microforms, word processing, video and audio devices--may be utilized by American farmers and ranchers.…

Telecommunications media for the delivery of educational programming

NASA Technical Reports Server (NTRS)

Ballard, R.; Eastwood, L. F., Jr.

1974-01-01

The technical characteristics of various telecommunications media are examined for incorporation into educational networks. FM radio, AM radio, and VHF and UHF television are considered along with computer-aided instruction. The application of iteration networks to library systems, and microform technology are discussed. The basic principles of the communications theory are outlined, and the operation of the PLATO 4 random access system is described.

Information Hang-Ups; Problems Encountered by Users of the Technical Information Services Offered by DDC and CFSTI, with Recommendations for the Future.

ERIC Educational Resources Information Center

Committee of DDC Users in the Greater Washington, DC. Area, Washington, DC.

A change in policy of the Defense Documentation Center (DDC) with regard to supplying hard copy and/or microforms of reports caused problems to users of the DDC Technical Report Service. Discussions among users of the service, a questionnaire survey and committee reports summarized basic user concerns, provided selected statistics and a look at…

A Program to Demonstrate the Uses of an Inexpensive Microfiche Reader, and the Resources of ERIC and Other Microform Information Collections. Final Report.

ERIC Educational Resources Information Center

Svobodny, Dolly D.

In order for the ERIC (Educational Resources Information Center) microfiche and the MLA (Modern Language Association of America) abstract system to have maximum impact, it was felt that scholars and teachers would need to own their own microfiche readers and that the potential of microfiche must be demonstrated to this same audience. A low-cost…

Molecular analysis of holoprosencephaly in South America

PubMed Central

Savastano, Clarice Pagani; El-Jaick, Kênia Balbi; Costa-Lima, Marcelo Aguiar; Abath, Cristina Maria Batista; Bianca, Sebastiano; Cavalcanti, Denise Pontes; Félix, Têmis Maria; Scarano, Gioacchino; Llerena, Juan Clinton; Vargas, Fernando Regla; Moreira, Miguel Ângelo Martins; Seuánez, Hector N.; Castilla, Eduardo Enrique; Orioli, Iêda Maria

2014-01-01

Holoprosencephaly (HPE) is a spectrum of brain and facial malformations primarily reflecting genetic factors, such as chromosomal abnormalities and gene mutations. Here, we present a clinical and molecular analysis of 195 probands with HPE or microforms; approximately 72% of the patients were derived from the Latin American Collaborative Study of Congenital Malformations (ECLAMC), and 82% of the patients were newborns. Alobar HPE was the predominant brain defect in almost all facial defect categories, except for patients without oral cleft and median or lateral oral clefts. Ethmocephaly, cebocephaly, and premaxillary agenesis were primarily observed among female patients. Premaxillary agenesis occurred in six of the nine diabetic mothers. Recurrence of HPE or microform was approximately 19%. The frequency of microdeletions, detected using Multiplex Ligation-dependant Probe Amplification (MLPA) was 17% in patients with a normal karyotype. Cytogenetics or QF-PCR analyses revealed chromosomal anomalies in 27% of the probands. Mutational analyses in genes SHH, ZIC2, SIX3 and TGIF were performed in 119 patients, revealing eight mutations in SHH, two mutations in SIX3 and two mutations in ZIC2. Thus, a detailed clinical description of new HPE cases with identified genetic anomalies might establish genotypic and phenotypic correlations and contribute to the development of additional strategies for the analysis of new cases. PMID:24764759

Video-Based Systems Research, Analysis, and Applications Opportunities

DTIC Science & Technology

1981-07-30

as a COM software consultant, marketing its own COMTREVE software; * DatagraphiX Inc., San Diego, offers several versions of its COM recorders. AutoCOM...Metropolitan Microforms Ltd. in New York markets its MCAR system, which satisfies the need for a one- or multiple-user information retrieval and input...targeted to the market for high-speed data communications within a single facility, such as a university campus. The first commercial installations were set

Improving Paper Machine Efficiency/Productivity through On-line Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cyrus K Aidun

2007-08-31

This project involves implementing a new technology, microforming, in a headbox to produce an isotropic sheet with significant reductions in the MD/CD stiffness ratio (increasing CD specific STFI) and improved sheet uniformity. Microforming involves generating axial vorticity (i.e., swirl) prior to the converging nozzle of the headbox by retrofitting an existing tube block with swirl generation devices referred to as Vortigen system. The Vortigen system developed in this project is a retrofit technology to a hydraulic headbox tube block. The tubes in the tube block are re-designed to generate axial vorticity (or swirl) in the tubes. This type of flowmore » results in higher intensity small-scale turbulence in the forming jet at the slice. The net effect, as demonstrated in pilot and commercial trials, is improvement in formation and surface smoothness, lower MD/CD tensile ratio, and consequently, higher CD strength properties such as CD STFI, Ring Crush and tensile or breaking length. The objective of this project is to implement microforming by developing the retrofit technology for generation and on-line control of axial vorticity in the tubes to optimize turbulent scale and intensity, and consequently, fiber network structure properties in the sheet. This technology results in significant improvements in the performance and capital effectiveness of the paper machine (PM) for a fraction of the cost to replace a headbox. In this project we have developed and demonstrated the concept of generating axial vorticity to control the fiber orientation in the converging zone of the headbox, and to produce a sheet with isotropic fiber orientation. The technology developed here has been demonstrated in static form on several pilot trials and two series of commercial trials. The economic feasibility of this technology is based primarily on fiber savings in cases where a more isotropic fiber orientation can be used to reduce the basis weight of the product. Even a 5% decrease in basis weight will results in substantial savings covering the cost of a commercial retrofit in 6 months or less in a medium size machine. The project also resulted in significant amount of information on fiber orientation in turbulent flow and in a converging nozzle where the results can be used in other applications, such as formation of composite materials. Several MS and Ph.D. students and postdoctoral associates have been trained as part of this project.« less

Multi-focal multiphoton lithography.

PubMed

Ritschdorff, Eric T; Nielson, Rex; Shear, Jason B

2012-03-07

Multiphoton lithography (MPL) provides unparalleled capabilities for creating high-resolution, three-dimensional (3D) materials from a broad spectrum of building blocks and with few limitations on geometry, qualities that have been key to the design of chemically, mechanically, and biologically functional microforms. Unfortunately, the reliance of MPL on laser scanning limits the speed at which fabrication can be performed, making it impractical in many instances to produce large-scale, high-resolution objects such as complex micromachines, 3D microfluidics, etc. Previously, others have demonstrated the possibility of using multiple laser foci to simultaneously perform MPL at numerous sites in parallel, but use of a stage-scanning system to specify fabrication coordinates resulted in the production of identical features at each focal position. As a more general solution to the bottleneck problem, we demonstrate here the feasibility for performing multi-focal MPL using a dynamic mask to differentially modulate foci, an approach that enables each fabrication site to create independent (uncorrelated) features within a larger, integrated microform. In this proof-of-concept study, two simultaneously scanned foci produced the expected two-fold decrease in fabrication time, and this approach could be readily extended to many scanning foci by using a more powerful laser. Finally, we show that use of multiple foci in MPL can be exploited to assign heterogeneous properties (such as differential swelling) to micromaterials at distinct positions within a fabrication zone.

A Guide to the Microform Collections of the USMA (United States Military Academy) Library,

DTIC Science & Technology

1983-01-01

array of material about the Manhattan Project and the atomic bombings of Hiroshima and Nagasaki; none of it was declassified until 1976. Foremost among...1946. The twenty-one page printed A Guide to the Manhattan Project : Official History and Documents, located on top of the metal cabinets in Room 212, is...organizational characteristics of the Manhattan Project . The seven succeeding books discussed the 49 various sub-projects of the effort, such as Book III

Dental developmental abnormalities in a patient with subtelomeric 7q36 deletion syndrome may confirm a novel role for the SHH gene☆

PubMed Central

Linhares, Natália D.; Svartman, Marta; Salgado, Mauro Ivan; Rodrigues, Tatiane C.; da Costa, Silvia S.; Rosenberg, Carla; Valadares, Eugênia R.

2013-01-01

Studies in mice demonstrated that the Shh gene is crucial for normal development of both incisors and molars, causing a severe retardation in tooth growth, which leads to abnormal placement of the tooth in the jaw and disrupted tooth morphogenesis. In humans the SHH gene is located on chromosome 7q36. Defects in its protein or signaling pathway may cause holoprosencephaly spectrum, a disorder in which the developing forebrain fails to correctly separate into right and left hemispheres and that can be manifested in microforms such as single maxillary central incisor. A novel role for this gene in the developing human primary dentition was recently demonstrated. We report a 12-year old boy with a de novo 7q36.1-qter deletion characterized by high-resolution karyotyping, oligonucleotide aCGH and FISH. His phenotype includes intellectual disability, non-verbal communication, hypospadia, partial sacral agenesis and absence of coccyx, which are distinctive features of the syndrome and mainly correlated with the MNX1, HTR5A and EN2 genes. No microforms of holoprosencephaly spectrum were observed; but the patient had diastema and dental developmental abnormalities, such as conical, asymmetric and tapered inferior central incisors. The dental anomalies are reported herein for the first time in subtelomeric 7q36 deletion syndrome and may confirm clinically a novel role for the SHH gene in dental development. PMID:25606385

Boc modifies the spectrum of holoprosencephaly in the absence of Gas1 function

PubMed Central

Seppala, Maisa; Xavier, Guilherme M.; Fan, Chen-Ming; Cobourne, Martyn T.

2014-01-01

ABSTRACT Holoprosencephaly is a heterogeneous developmental malformation of the central nervous system characterized by impaired forebrain cleavage, midline facial anomalies and wide phenotypic variation. Indeed, microforms represent the mildest manifestation, associated with facial anomalies but an intact central nervous system. In many cases, perturbations in sonic hedgehog signaling are responsible for holoprosencephaly. Here, we have elucidated the contribution of Gas1 and an additional hedgehog co-receptor, Boc during early development of the craniofacial midline, by generating single and compound mutant mice. Significantly, we find Boc has an essential role in the etiology of a unique form of lobar holoprosencephaly that only occurs in conjunction with combined loss of Gas1. Whilst Gas1−/− mice have microform holoprosencephaly characterized by a single median maxillary central incisor, cleft palate and pituitary anomalies, Boc−/− mice have a normal facial midline. However, Gas1−/−; Boc−/− mutants have lobar holoprosencephaly associated with clefting of the lip, palate and tongue, secondary to reduced sonic hedgehog transduction in the central nervous system and face. Moreover, maxillary incisor development is severely disrupted in these mice, arresting prior to cellular differentiation as a result of apoptosis in the odontogenic epithelium. Thus, Boc and Gas1 retain an essential function in these tooth germs, independent of their role in midline development of the central nervous system and face. Collectively, this phenotype demonstrates both redundancy and individual requirements for Gas1 and Boc during sonic hedgehog transduction in the craniofacial midline and suggests BOC as a potential digenic locus for lobar holoprosencephaly in human populations. PMID:25063195

Cryophenomena in the Cold Desert of Atacama

NASA Astrophysics Data System (ADS)

Buchroithner, Dr.; Trombotto, Dr.

2012-04-01

The study area of the Valle de Barrancas Blancas in the High Atacama Andes of Chile (68°39' W, 27°02' S), a kind of Patagonian "bajo sin salida", shows well preserved landforms resulting from a combination of slope, eolian, lacustrine/litoral, fluvial, glacial and periglacial regimes. They permit the reconstruction of geomorphological processes within this isolated catchment of approximately 160 km2. The mean annual air temperature varies between -2 and -4 °C and the precipitation is approximately 150 mm/a. Snowfall is frequent but the snow is quickly sublimated, redeposited and/or covered by cryosediments, i.e. mainly pumice pebbles. Water bodies present icings, even in summer. Regarding its climatic conditions the study area represents an extremely cold desertic region. Extremophile microfauna was also found. The area displays both in situ mountain permafrost and creeping permafrost. The active layer is 30 to 45 cm thick. It is a periglacial macro-environment where interdependent processes, and not only cryogenic processes but also erosion and eolian deposition and the action of fluvial washout mainly caused by precipitation, accumulation, retransportation/redeposition and melting of snow, play an important role. The cryogenic geomorphology of the Valle de Barrancas Blancas is varied and contains microforms such as patterned ground and microforms caused by cryoturbation, as well as mesoforms like rockglaciers and cryoplanation surfaces. Slopes are strongly affected by gelifluction. New cryoforms in South America and in the Southern Hemisphere like the Atacama Pingo (Pingo atacamensis) and Permafrosted Dunes ("Dunas heladas") were found. Intense niveo-eolian processes participate in the erosion of preexisting landforms, in the formation of subterraneous ice layers, and the retransportation/redeposition of snow and sediments. Studies of this periglacial environment are crucial for the understanding of Tundrean paleoenvironments and Martian conditions.

Dynamic effect in ultrasonic assisted micro-upsetting

NASA Astrophysics Data System (ADS)

Presz, Wojciech

2018-05-01

The use of ultrasonic assistance in microforming is becoming more and more popular. Mainly due to the beneficial effect of vibrations on the flow of plastic deformation reported already in the 50s of the last century. The influence is of two types: surface and volume. The surface effect is mainly the reduction of friction forces, and volumetric is the impact on the dislocation movement and even on phase transitions. The work focuses on the dynamic aspect of vibration assisted microforming. The use of ultrasonic vibrations at a frequency of 20 kHz and an amplitude of 16 µm, in the micro-upsetting process of an aluminum sample resulted in a high concentration of strain on both ends of the sample - at 14% of the height on both sides. There was observed (in relation to deformations of the sample without vibrations) 150-250% increase and a 50% decrease in strain in the center of the sample. At the same time, the larger deformations occurred from the impact side of the punch. Analyzing the course of forces of the upsetting process in the loading and unloading phase as well as the process of breaking glass samples, the spring deflections of key system elements and their natural frequencies were determined or calculated. Based on the determined or calculated parameters of the test stand, it was shown that during the micro-upsetting process the punch may detach from the sample surface and this is the main reason for the phenomena occurring. Detach of the punch is also the cause of the observed instability of the measurement of force, which should be considered unbelievable in such a situation.

Manual of Documentation Practices Applicable to Defence-Aerospace Scientific and Technical Information. Volume 3. Section 7 - Information Retrieval. Section 8 - Dissemination Practices. Section 9 - Microform Systems and Reprography

DTIC Science & Technology

1980-10-01

Location Flowchart has been drawn up to give guidance as to where to apply for various categories of reports. It also serves as an aid in deciding whether...or further disclosure S.l-. 72 NOTES 1. The flowchart is not intended to cover all possibilities; the following points are made for your guidance. 2...not followed the flowchart correctly - start again from ’BEGIN’. NEI N ’"A. 7-.1 %. 73 REPORT LOCATION BEGIN~ FLOWCHART rreporto aD-P.orriBR6N~I-D ubr

Length and Dimensional Measurements at NIST

PubMed Central

Swyt, Dennis A.

2001-01-01

This paper discusses the past, present, and future of length and dimensional measurements at NIST. It covers the evolution of the SI unit of length through its three definitions and the evolution of NBS-NIST dimensional measurement from early linescales and gage blocks to a future of atom-based dimensional standards. Current capabilities include dimensional measurements over a range of fourteen orders of magnitude. Uncertainties of measurements on different types of material artifacts range down to 7×10−8 m at 1 m and 8 picometers (pm) at 300 pm. Current work deals with a broad range of areas of dimensional metrology. These include: large-scale coordinate systems; complex form; microform; surface finish; two-dimensional grids; optical, scanning-electron, atomic-force, and scanning-tunneling microscopies; atomic-scale displacement; and atom-based artifacts. PMID:27500015

Microforms in gravel bed rivers: Formation, disintegration, and effects on bedload transport

USGS Publications Warehouse

Strom, K.; Papanicolaou, A.N.; Evangelopoulos, N.; Odeh, M.

2004-01-01

This research aims to advance current knowledge on cluster formation and evolution by tackling some of the aspects associated with cluster microtopography and the effects of clusters on bedload transport. The specific objectives of the study are (1) to identify the bed shear stress range in which clusters form and disintegrate, (2) to quantitatively describe the spacing characteristics and orientation of clusters with respect to flow characteristics, (3) to quantify the effects clusters have on the mean bedload rate, and (4) to assess the effects of clusters on the pulsating nature of bedload. In order to meet the objectives of this study, two main experimental scenarios, namely, Test Series A and B (20 experiments overall) are considered in a laboratory flume under well-controlled conditions. Series A tests are performed to address objectives (1) and (2) while Series B is designed to meet objectives (3) and (4). Results show that cluster microforms develop in uniform sediment at 1.25 to 2 times the Shields parameter of an individual particle and start disintegrating at about 2.25 times the Shields parameter. It is found that during an unsteady flow event, effects of clusters on bedload transport rate can be classified in three different phases: a sink phase where clusters absorb incoming sediment, a neutral phase where clusters do not affect bedload, and a source phase where clusters release particles. Clusters also increase the magnitude of the fluctuations in bedload transport rate, showing that clusters amplify the unsteady nature of bedload transport. A fourth-order autoregressive, autoregressive integrated moving average model is employed to describe the time series of bedload and provide a predictive formula for predicting bedload at different periods. Finally, a change-point analysis enhanced with a binary segmentation procedure is performed to identify the abrupt changes in the bedload statistic characteristics due to the effects of clusters and detect the different phases in bedload time series using probability theory. The analysis verifies the experimental findings that three phases are detected in the bedload rate time series structure, namely, sink, neutral, and source. ?? ASCE / JUNE 2004.

Delineation of gravel-bed clusters via factorial kriging

NASA Astrophysics Data System (ADS)

Wu, Fu-Chun; Wang, Chi-Kuei; Huang, Guo-Hao

2018-05-01

Gravel-bed clusters are the most prevalent microforms that affect local flows and sediment transport. A growing consensus is that the practice of cluster delineation should be based primarily on bed topography rather than grain sizes. Here we present a novel approach for cluster delineation using patch-scale high-resolution digital elevation models (DEMs). We use a geostatistical interpolation method, i.e., factorial kriging, to decompose the short- and long-range (grain- and microform-scale) DEMs. The required parameters are determined directly from the scales of the nested variograms. The short-range DEM exhibits a flat bed topography, yet individual grains are sharply outlined, making the short-range DEM a useful aid for grain segmentation. The long-range DEM exhibits a smoother topography than the original full DEM, yet groupings of particles emerge as small-scale bedforms, making the contour percentile levels of the long-range DEM a useful tool for cluster identification. Individual clusters are delineated using the segmented grains and identified clusters via a range of contour percentile levels. Our results reveal that the density and total area of delineated clusters decrease with increasing contour percentile level, while the mean grain size of clusters and average size of anchor clast (i.e., the largest particle in a cluster) increase with the contour percentile level. These results support the interpretation that larger particles group as clusters and protrude higher above the bed than other smaller grains. A striking feature of the delineated clusters is that anchor clasts are invariably greater than the D90 of the grain sizes even though a threshold anchor size was not adopted herein. The average areal fractal dimensions (Hausdorff-Besicovich dimensions of the projected areas) of individual clusters, however, demonstrate that clusters delineated with different contour percentile levels exhibit similar planform morphologies. Comparisons with a compilation of existing field data show consistency with the cluster properties documented in a wide variety of settings. This study thus points toward a promising, alternative DEM-based approach to characterizing sediment structures in gravel-bed rivers.

Holoprosencephaly: from Homer to Hedgehog.

PubMed

Ming, J E; Muenke, M

1998-03-01

Holoprosencephaly (HPE), a common developmental defect affecting the forebrain and face, is etiologically heterogeneous and exhibits wide phenotypic variation. Graded degrees of severity of the brain malformation are also reflected in the highly variable craniofacial malformations associated with HPE. In addition, individuals with microforms of HPE, who usually have normal cognition and normal brain imaging, are at risk for having children with HPE. Some obligate carriers for HPE may not have any phenotypic abnormalities. Recurrent chromosomal rearrangements in individuals with HPE suggest loci containing genes important for brain development, and abnormalities in these genes may result in HPE. Recently, Sonic Hedgehog (SHH) was the first gene identified as causing HPE in humans. Proper function of SHH depends on cholesterol modification. Other candidate genes that may be involved in HPE include components of the SHH pathway, elements involved in cholesterol metabolism, and genes expressed in the developing forebrain.

[Nasolabial muscle finite-element study and clinical application].

PubMed

Yin, Ningbei; Wu, Jiajun; Chen, Bo; Wang, Yongqian; Song, Tao; Ma, Hengyuan

2015-05-01

To investigate the nasolabial muscle anatomy and biomechanical characteristics. Micro-computed tomography scan was performed in 8 cases of spontaneous abortion fetus lip nasal specimens to construct a three-dimensional model. The nasolabial muscle structure was analyzed using Mimics software. The three-dimensional configuration model of nasolabial muscle was established based on local anatomy and tissue section, and compared with tissue section. Three dimensional finite element analysis was performed on lip nasal muscle related biomechanics and surface deformation in Application verification was carried out in 263 cases of microform cleft lip surgery. There was close relationship between nasolabial muscle. The nasolabial muscle tension system was constituted, based on which a new cleft lip repair surgery was designed and satisfied results were achieved. There is close relationship among nasolabial muscle in anatomy, histology and biomechanics. To obtain better effect, cleft lip repair should be performed on the basis of recovering muscle tension system.

The study on deformation characterization in micro rolling for ultra-thin strip

NASA Astrophysics Data System (ADS)

Xie, H. B.; Manabe, K.; Furushima, T.; Jiang, Z. Y.

2013-12-01

The demand for miniaturized parts and miniaturized semi-finished products is increasing. Metal forming processes cannot be simply scaled down to produce miniaturized micro parts and microforming processes have the capability of improving mass production and minimizing material waste. In this study, experimental and theoretical investigations on the micro rolling process have proven that the micro rolling deformation of thin strip is influenced by size effects from specimen sizeon flow stress and friction coefficient. The analytical and finite element (FE) models for describing the size effect related phenomena for SUS 304 stainless steel, such as the change of flow stress, friction and deformation behaviour, are proposed. The material surface constraint and the material deformation mode are critical in determination of material flow stress curve. The identified deformation and mechanics behaviours provide a basis for further exploration of the material deformation behaviour in plastic deformation of micro scale and the development of micro scale products via micro rolling.

EP and CD-ROM products - Current trends of production and market development -

NASA Astrophysics Data System (ADS)

Watanabe, Kazuhiko

The printed books and magazines/journals have been, and still even now are, dominant materials for public reading and reference usage. Microform publications have been also adopted for library collection build-up, but it is still within a very limited scale and coverage. As the first "new media" product, we should approve the fact that "CD-ROM" keeps amazingly large information storage capacity and also quite flexible application utility. So far, among the firstly released CD-ROMS, bibliographic databases, both for Japanese and English publications, look already quite widely purchased and now installed in many workstations of libraries. The users should evaluate its cost-effectiveness not only by its great data storage capacity but also by its frequent usage merit for library work rationalization. Multiple applied usage of CD-ROM will surely serve to such library routine works as searching, cataloguing, reading list preparation, inventory checking and new order placing, etc. 'CD-ROM' is the first EP product for quite wide usage.

Investigations on the micro-scale surface interactions at the tool and workpiece interface in micro-manufacturing of bipolar plates for proton exchange membrane fuel cells

NASA Astrophysics Data System (ADS)

Peker, Mevlut Fatih

Micro-forming studies have been more attractive in recent years because of miniaturization trend. One of the promising metal forming processes, micro-stamping, provides durability, strength, surface finish, and low cost for metal products. Hence, it is considered a prominent method for fabricating bipolar plates (BPP) with micro-channel arrays on large metallic surfaces to be used in Proton Exchange Membrane Fuel Cells (PEMFC). Major concerns in micro-stamping of high volume BPPs are surface interactions between micro-stamping dies and blank metal plates, and tribological changes. These concerns play a critical role in determining the surface quality, channel formation, and dimensional precision of bipolar plates. The surface quality of BPP is highly dependent on the micro-stamping die surface, and process conditions due to large ratios of surface area to volume (size effect) that cause an increased level of friction and wear issues at the contact interface. Due to the high volume and fast production rates, BPP surface characteristics such as surface roughness, hardness, and stiffness may change because of repeated interactions between tool (micro-forming die) and workpiece (sheet blank of interest). Since the surface characteristics of BPPs have a strong effect on corrosion and contact resistance of bipolar plates, and consequently overall fuel cell performance, evolution of surface characteristics at the tool and workpiece should be monitored, controlled, and kept in acceptable ranges throughout the long production cycles to maintain the surface quality. Compared to macro-forming operations, tribological changes in micro-forming process are bigger challenges due to their dominance and criticality. Therefore, tribological size effect should be considered for better understanding of tribological changes in micro-scale. The integrity of process simulation to the experiments, on the other hand, is essential. This study describes an approach that aims to investigate the surface topography changes during long-run micro-stamping of BPPs, and establish relationships between surface roughness--corrosion resistance and surface roughness-contact resistance characteristics of BPPs. Formability levels of formed BPPs and repeatability characteristics of the process were investigated. In addition, blank thickness changes, von-Mises stress, plastic strain levels and distributions of micro-stamping process were determined via finite element analysis (FEA). Test results revealed that the surface roughness change for the stamping dies and BPPs was unsteady (no trend) due to the continuous change of surface topography (i.e. asperity deformation). Sub-micron range local plastic deformations on stamping dies led to surface topography changes on BPP in long-run manufacturing case. As surface defects trigger corrosion, the correlation between surface roughness and corrosion resistance of BPPs was found to be direct. Increasing number of surface irregularities (asperities) lowered contact surface area that resulted in increased contact resistance. ZrN coated BPPs, on the other hand, did not change surface roughness, however; it improved the protection of BPPs against corrosion significantly. In addition, ZrN coating increased the conductivity of BPPs and reduced the contact resistance between BPP and gas diffusion layer (GDL), at certain extent. As dimensional stability and repeatability was confirmed in forming of both uncoated and coated BPPs during the long run manufacturing, different formability levels were achieved for coated and uncoated samples. Lower channel height values were obtained for coated plates because of the different surface hardness of uncoated and coated plates. In tribological size effect part of study, micro stamping experiments using three different dies with distinct channel height values at different stamping force levels were performed. It was concluded that decrease in forming die dimensions led to increase in coefficient of friction as previously reported by other researchers as one of the consequences of tribological size effect. On the other hand, coefficient of friction values were not affected by the force levels used in the experiments and simulations, whereas plastic strain, equivalent stress, and formability levels were increased with increasing stamping force, as expected. In essence, this study proposed a methodology to investigate the long-run manufacturing effects on dimensional stability and surface characteristics of micro-stamped sheets. It also correlates these parameters to fuel cell performance measures such as interfacial contact and corrosion resistance.

Experimental and Theoretical Study on Minimum Achievable Foil Thickness during Asymmetric Rolling

PubMed Central

Tang, Delin; Liu, Xianghua; Song, Meng; Yu, Hailiang

2014-01-01

Parts produced by microforming are becoming ever smaller. Similarly, the foils required in micro-machines are becoming ever thinner. The asymmetric rolling technique is capable of producing foils that are thinner than those produced by the conventional rolling technique. The difference between asymmetric rolling and conventional rolling is the ‘cross-shear’ zone. However, the influence of the cross-shear zone on the minimum achievable foil thickness during asymmetric rolling is still uncertain. In this paper, we report experiments designed to understand this critical influencing factor on the minimum achievable thickness in asymmetric rolling. Results showed that the minimum achievable thickness of rolled foils produced by asymmetric rolling with a rolling speed ratio of 1.3 can be reduced to about 30% of that possible by conventional rolling technique. Furthermore, the minimum achievable thickness during asymmetric rolling could be correlated to the cross-shear ratio, which, in turn, could be related to the rolling speed ratio. From the experimental results, a formula to calculate the minimum achievable thickness was established, considering the parameters cross-shear ratio, friction coefficient, work roll radius, etc. in asymmetric rolling. PMID:25203265

Carbon dioxide flux and net primary production of a boreal treed bog: responses to warming and water table manipulations

NASA Astrophysics Data System (ADS)

Munir, T. M.; Perkins, M.; Kaing, E.; Strack, M.

2014-09-01

Mid-latitude treed bogs are significant carbon (C) stocks and are highly sensitive to global climate change. In a dry continental treed bog, we compared three sites; control, recent (1-3 years; experimental) and older drained (10-13 years; drained) with water levels at 38, 74 and 120 cm below the surface, respectively. At each site we measured carbon dioxide (CO2) fluxes and tree root respiration (Rr) (across hummock-hollow microtopography of the forest floor) and net primary production (NPP) of trees during the growing seasons (May to October) of 2011-2013. The carbon (C) balance was calculated by adding net CO2 exchange of the forest floor (NEff-Rr) to the NPP of the trees. From cooler and wetter 2011 to driest and warmest 2013, The control site was a~C sink of 92, 70 and 76 g m-2, experimental site was a C source of 14, 57 and 135 g m-2, and drained site was a progressively smaller source of 26, 23 and 13 g m-2, respectively. Although all microforms at the experimental site had large net CO2 emissions, the longer-term drainage and deeper water level at the drained site resulted in the replacement of mosses with vascular plants (shrubs) at the hummocks and lichens at the hollows leading to the highest CO2 uptake at drained hummocks and significant losses at hollows. The tree NPP was highest at the drained site. We also quantified the impact of climatic warming at all water table treatments by equipping additional plots with open-top chambers (OTCs) that caused a passive warming on average of ∼1 °C and differential air warming of ∼6 °C (at mid-day full sun) across the study years. Warming significantly enhanced the shrub growth and CO2 sink function of the drained hummocks (exceeding the cumulative respiration losses at hollows induced by the lowered water level × warming). There was an interaction of water level with warming across hummocks that resulted in largest net CO2 uptake at warmed drained hummocks. Thus in 2013, the warming treatment enhanced the sink function of control by 13 g m-2, reduced the source function of experimental by 10 g m-2, and significantly enhanced the sink function of the drained site by 73 g m-2. Therefore, drying and warming in continental bogs is expected to initially accelerate C losses via respiration but persistent drought and warming is expected to restore the peatland's original C sink function as a result of transitional shift of vegetation between the microforms and increased NPP of trees over time.

Microstructural Evolution at Micro/Meso-Scale in an Ultrafine-Grained Pure Aluminum Processed by Equal-Channel Angular Pressing with Subsequent Annealing Treatment.

PubMed

Xu, Jie; Li, Jianwei; Zhu, Xiaocheng; Fan, Guohua; Shan, Debin; Guo, Bin

2015-11-04

Micro-forming with ultrafine-grained (UFG) materials is a promising direction for the fabrication of micro-electro-mechanical systems (MEMS) components due to the improved formability, good surface quality, and excellent mechanical properties it provides. In this paper, micro-compression tests were performed using UFG pure aluminum processed by equal-channel angular pressing (ECAP) with subsequent annealing treatment. Microstructural evolution was investigated by electron back-scattered diffraction (EBSD) and transmission electron microscopy (TEM). The results show that microstructural evolutions during compression tests at the micro/meso-scale in UFG pure Al are absolutely different from the coarse-grained (CG) materials. A lot of low-angle grain boundaries (LAGBs) and recrystallized fine grains are formed inside of the original large grains in CG pure aluminum after micro-compression. By contrast, ultrafine grains are kept with few sub-grain boundaries inside the grains in UFG pure aluminum, which are similar to the original microstructure before micro-compression. The surface roughness and coordinated deformation ability can be signmicrostructure; micro/meso-forming; ultrafine grains; ECAP; aluminumificantly improved with UFG pure aluminum, which demonstrates that the UFG materials have a strong potential application in micro/meso-forming.

Modeling of flow stress size effect based on variation of dislocation substructure in micro-tension of pure nickel

NASA Astrophysics Data System (ADS)

Wang, Chuanjie; Liu, Huan; Zhang, Ying; Chen, Gang; Li, Yujie; Zhang, Peng

2017-12-01

Micro-forming is one promising technology for manufacturing micro metal parts. However, the traditional metal-forming theories fail to analyze the plastic deformation behavior in micro-scale due to the size effect arising from the part geometry scaling down from macro-scale to micro-scale. To reveal the mechanism of plastic deformation behavior size effect in micro-scale, the geometrical parameters and the induced variation of microstructure by them need to be integrated in the developed constitutive models considering the free surface effect. In this research, the variations of dislocation cell diameter with original grain size, strain and location (surface grain or inner grain) are derived according the previous research data. Then the overall flow stress of the micro specimen is determined by employing the surface layer model and the relationship between dislocation cell diameter and the flow stress. This new developed constitutive model considers the original grain size, geometrical dimension and strain simultaneously. The flow stresses in micro-tensile tests of thin sheets are compared with calculated results using the developed constitutive model. The calculated and experimental results match well. Thus the validity of the developed constitutive model is verified.

Toxic behavior of silver and zinc oxide nanoparticles on environmental microorganisms.

PubMed

Dhas, Sindhu Priya; Shiny, Punalur John; Khan, Sudheer; Mukherjee, Amitava; Chandrasekaran, Natrajan

2014-09-01

Silver and zinc oxide nanoparticles (Ag and ZnO NPs) are widely used as antimicrobial agents. However, their potential toxicological impact on environmental microorganisms is largely unexplored. The aim of this work was to investigate the sensitivity and adaptability of five bacterial species isolated from sewage towards Ag and ZnO NPs. The bacterial species were exposed to increasing concentration of nanoparticles and the growth inhibitory effect, exopolysaccharides (EPSs) and extracellular proteins (ECPs) productions were determined. The involvement of surface charge in nanoparticles toxicity was also determined. The bacterial species were constantly exposed to nanoparticles to determine the adaptation behavior toward nanoparticles. The nanoparticles exhibited remarkable growth inhibitory effect on tested bacterial species. The toxicity of nanoparticles was found to be strongly dependent on surface charge effects. Though, these organisms are highly sensitive to Ag and ZnO NPs, the continuous exposure to these nanoparticles leads to moderate adaptation of bacterial species and the adapted bacterial species convert the highly toxic nano form to less toxic microform. Finally we predict that the continuing applications of nanoparticles in consumer products may lead to the development of nanoparticles resistant bacterial strains in future. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Detection of orbicularis oris muscle defects in first degree relatives of cleft lip children using ultrasound.

PubMed

Mittal, M; Maheshwari, N; Ahlawat, K; Sharma, V; Sultan, A; Chopra, R

2012-01-01

The severity of cleft lip (CL) varies considerably from complete bilateral CL and palate at one end of the spectrum to a minimal CL at the other. In some cases of microform clefting, there may be no visible manifestation of the defect on the lip surface (i.e., the defect is occult) and no residual functional deficit. This study used high resolution ultrasonography to detect subclinical anomalies of orbicularis oris muscle (OOM) in first degree relatives of CL +- cleft palate children and compared it with controls. Thirty relatives of 25 children with non-syndromic CL or CL+ CP were identified for the study. Thirty subjects having negative family history of CL/P in three generations and absence of any minimal cleft features were taken as controls. Ultrasound scans of OOM of all the controls and relatives were taken. Statistical analysis was performed using standard χ2 tests with Yates correction. Defects were seen in 13.3% of relatives and no defects were seen in controls, this was not statistically significant. The data support the hypothesis that subclinical CL cases with subepithelial OOM defects do exist and Orbicularis oris discontinuities represent the mildest form of CL.

Determination of material distribution in heading process of small bimetallic bar

NASA Astrophysics Data System (ADS)

Presz, Wojciech; Cacko, Robert

2018-05-01

The electrical connectors mostly have silver contacts joined by riveting. In order to reduce costs, the core of the contact rivet can be replaced with cheaper material, e.g. copper. There is a wide range of commercially available bimetallic (silver-copper) rivets on the market for the production of contacts. Following that, new conditions in the riveting process are created because the bi-metal object is riveted. In the analyzed example, it is a small size object, which can be placed on the border of microforming. Based on the FEM modeling of the load process of bimetallic rivets with different material distributions, the desired distribution was chosen and the choice was justified. Possible material distributions were parameterized with two parameters referring to desirable distribution characteristics. The parameter: Coefficient of Mutual Interactions of Plastic Deformations and the method of its determination have been proposed. The parameter is determined based of two-parameter stress-strain curves and is a function of these parameters and the range of equivalent strains occurring in the analyzed process. The proposed method was used for the upsetting process of the bimetallic head of the electrical contact. A nomogram was established to predict the distribution of materials in the head of the rivet and the appropriate selection of a pair of materials to achieve the desired distribution.

Primary journal selection using citations from an indexing service journal: a method and example from nursing literature.

PubMed Central

Hafner, A W

1976-01-01

Although serial literature is extremely important to a library collection, it is also the source of many problems. Specialty journal selection is difficult, particularly for the librarian of a small or intermediate-size library that is not in a position to develop or maintain an exhaustive or inclusive collection in a particular field or discipline. Steadily increasing journal costs and recent economic trends necessitate establishment or reexamination of a periodical collection policy. In this investigation, the technique used analyzes citations assigned to medical subject headings (MeSH) and subheadings by indexers who prepare the MEDLARS data base. Citations have been retrieved by exploiting the on-line nature of the MEDLARS data base. A four-year time period is used to identify specialty journals in the area of nursing. Results given include a separate rank-order listing arranged by decreasing frequency of productivity for each MeSH term searched. A composite listing is given for the 16,355 unique citations retrieved. The approach illustrated and data presented may be useful in establishing library policy for questions of periodical subscription and setting of priorities for binding and microform purchases. The purpose of the approach described is to predict collection demand with efficiency and economy. PMID:974295

Re-assessing the vertical distribution of testate amoeba communities in surface peats: Implications for palaeohydrological studies.

PubMed

Roe, Helen M; Elliott, Suzanne M; Patterson, R Timothy

2017-08-01

Testate amoeba-derived transfer functions are frequently used in peatland palaeohydrological studies and involve the development of training sets from surficial peats. However, within acrotelmic peats, considerable vertical variation in assemblage composition can occur, particularly along Sphagnum stems, which may limit the representation of the associated 'contemporary' testate amoeba samples as analogues for the peatland surface. This paper presents contiguous testate amoeba assemblage data from nine monoliths collected from different peatland microforms (hummock, hollow, lawn) in three Sphagnum dominated ombrotrophic peatlands in Ontario and Quebec, eastern Canada. The aim is to: (i) gain a greater understanding of the vertical distribution of xerophilous/hygrophilous taxa along Sphagnum stems; (ii) determine the vertical extent of live/encysted taxa along this gradient; and (iii) assess the significance of this distribution on surface sampling protocols. The results show that testate amoeba communities in the uppermost acrotelmic peat layers display considerable variability. This may reflect a complex interplay of abiotic and biotic controls, including moisture, temperature, light and other characteristics, food availability, and mineral particle availability for test construction. These findings underline the complexity of testate amoeba community structure and highlight the importance of analysing both living and dead Sphagnum stem sections when developing calibration sets. Copyright © 2017 Elsevier GmbH. All rights reserved.

A multi-scale controlled tissue engineering scaffold prepared by 3D printing and NFES technology

NASA Astrophysics Data System (ADS)

Yan, Feifei; Liu, Yuanyuan; Chen, Haiping; Zhang, Fuhua; Zheng, Lulu; Hu, Qingxi

2014-03-01

The current focus in the field of life science is the use of tissue engineering scaffolds to repair human organs, which has shown great potential in clinical applications. Extracellular matrix morphology and the performance and internal structure of natural organs are required to meet certain requirements. Therefore, integrating multiple processes can effectively overcome the limitations of the individual processes and can take into account the needs of scaffolds for the material, structure, mechanical properties and many other aspects. This study combined the biological 3D printing technology and the near-field electro-spinning (NFES) process to prepare a multi-scale controlled tissue engineering scaffold. While using 3D printing technology to directly prepare the macro-scaffold, the compositing NFES process to build tissue micro-morphology ultimately formed a tissue engineering scaffold which has the specific extracellular matrix structure. This scaffold not only takes into account the material, structure, performance and many other requirements, but also focuses on resolving the controllability problems in macro- and micro-forming which further aim to induce cell directed differentiation, reproduction and, ultimately, the formation of target tissue organs. It has in-depth immeasurable significance to build ideal scaffolds and further promote the application of tissue engineering.

Meletin sustained-release gliadin nanoparticles prepared via solvent surface modification on blending electrospraying

NASA Astrophysics Data System (ADS)

Yang, Yao-Yao; Zhang, Man; Liu, Zhe-Peng; Wang, Ke; Yu, Deng-Guang

2018-03-01

Almost all electrospraying processes are carried out under an air-solution interface, thereby overlooking the potential influence of an additional solvent surface modification between air and the working solution. A pure solvent was explored to temporarily and dynamically surround the solutions utilized for blending electrospraying, which contained a guest drug meletin and a protein drug carrier gliadin. The new modified processes created protein-based medicated nanoparticles (P2) with higher quality than their counterparts (P1) from blending processes, as demonstrated by the SEM and TEM images. Although the particles from the two processes were similar (nanocomposites), and the particles P1 were larger than P2, the later provided a better meletin sustained-release profile than the former. This finding was verified by the smaller initial burst release, longer sustained-release time period, and shorter late leveling-off stage. These unanticipated results were attributed to the rounder surface, the more uniform size distribution, and the smaller total surface area of particles P2 than P1. The microformation mechanism of the modified coaxial process was suggested. The protocols reported here paved a new way for the development of new kinds of functional nanoparticles by modifying the interfaces of working fluids during electrospraying.

Thyroxine-induced changes in the glycosylation pattern and in brain and serum levels of rat alpha-fetoprotein.

PubMed

Naval, J; Calvo, M; Lampreave, F; Piñeiro, A

1986-01-01

We have studied the effect of thyroid disfunction during the postnatal period, on the serum and brain levels of rat alpha-fetoprotein (AFP) and albumin. Hypothyroidism was induced by treatment of pregnant rats and their newborn pups with 2-mercapto-1-methylimidazole(methimazole). Hyperthyroidism was provoked in newborns by daily injections of thyroxine (0.25 micrograms/g body wt) from the 3rd postnatal day weaning. Impaired growth, lower brain size, altered behaviour and morphological features observed were according to an altered thyroid status. Hypothyroid rats showed a significantly reduction in serum AFP concentration (78% of control values at 8 days of age) and a slight increase in that of albumin. level could be appreciated. Thyroxine supplementation (0.2 micrograms/rat/day) corrected most of these alterations. Hyperthyroidism induced a drastic fall in both serum and brain AFP levels (about 48% of the corresponding control values). Albumin concentration in serum was augmented significantly from the 12th postnatal day, but its brain levels did not change significantly. In hyperthyroid rats, a significant reduction (37% relative to controls) in the concanavalin A-non reactive microform of AFP, was observed. This alteration of the glycosylation pattern of AFP could be due to the inhibition by thyroxine of the activity of the hepatic enzyme GlcNAc-transferase III.

High-speed microprobe for roughness measurements in high-aspect-ratio microstructures

NASA Astrophysics Data System (ADS)

Doering, Lutz; Brand, Uwe; Bütefisch, Sebastian; Ahbe, Thomas; Weimann, Thomas; Peiner, Erwin; Frank, Thomas

2017-03-01

Cantilever-type silicon microprobes with an integrated tip and a piezoresistive signal read out have successfully proven to bridge the gap between scanning force microscopy and stylus profilometry. Roughness measurements in high-aspect-ratio microstructures (HARMS) with depths down to 5 mm and widths down to 50 µm have been demonstrated. To improve the scanning speed up to 15 mm s-1, the wear of the tip has to be reduced. The atomic layer deposition (ALD) technique with alumina (Al2O3) has been tested for this purpose. Repeated wear measurements with coated and uncoated microprobe cantilevers have been carried out on a roughness standard at a speed of 15 mm s-1. The tip shape and the wear have been measured using a new probing tip reference standard containing rectangular silicon grooves with widths from 0.3 µm to 3 µm. The penetration depth of the microprobe allows one to measure the wear of the tip as well as the tip width and the opening angle of the tip. The roughness parameters obtained on the roughness standard during wear experiments agree well with the reference values measured with a calibrated stylus instrument, nevertheless a small amount of wear still is observable. Further research is necessary in order to obtain wear resistant microprobe tips for non-destructive inspection of microstructures in industry and microform measurements, for example in injection nozzles.

Mesoscopic Model — Advanced Simulation of Microforming Processes

NASA Astrophysics Data System (ADS)

Geißdörfer, Stefan; Engel, Ulf; Geiger, Manfred

2007-04-01

Continued miniaturization in many fields of forming technology implies the need for a better understanding of the effects occurring while scaling down from conventional macroscopic scale to microscale. At microscale, the material can no longer be regarded as a homogeneous continuum because of the presence of only a few grains in the deformation zone. This leads to a change in the material behaviour resulting among others in a large scatter of forming results. A correlation between the integral flow stress of the workpiece and the scatter of the process factors on the one hand and the mean grain size and its standard deviation on the other hand has been observed in experiments. The conventional FE-simulation of scaled down processes is not able to consider the size-effects observed such as the actual reduction of the flow stress, the increasing scatter of the process factors and a local material flow being different to that obtained in the case of macroparts. For that reason, a new simulation model has been developed taking into account all the size-effects. The present paper deals with the theoretical background of the new mesoscopic model, its characteristics like synthetic grain structure generation and the calculation of micro material properties — based on conventional material properties. The verification of the simulation model is done by carrying out various experiments with different mean grain sizes and grain structures but the same geometrical dimensions of the workpiece.

Carbon dioxide flux and net primary production of a boreal treed bog: Responses to warming and water-table-lowering simulations of climate change

NASA Astrophysics Data System (ADS)

Munir, T. M.; Perkins, M.; Kaing, E.; Strack, M.

2015-02-01

Midlatitude treed bogs represent significant carbon (C) stocks and are highly sensitive to global climate change. In a dry continental treed bog, we compared three sites: control, recent (1-3 years; experimental) and older drained (10-13 years), with water levels at 38, 74 and 120 cm below the surface, respectively. At each site we measured carbon dioxide (CO2) fluxes and estimated tree root respiration (Rr; across hummock-hollow microtopography of the forest floor) and net primary production (NPP) of trees during the growing seasons (May to October) of 2011-2013. The CO2-C balance was calculated by adding the net CO2 exchange of the forest floor (NEff-Rr) to the NPP of the trees. From cooler and wetter 2011 to the driest and the warmest 2013, the control site was a CO2-C sink of 92, 70 and 76 g m-2, the experimental site was a CO2-C source of 14, 57 and 135 g m-2, and the drained site was a progressively smaller source of 26, 23 and 13 g CO2-C m-2. The short-term drainage at the experimental site resulted in small changes in vegetation coverage and large net CO2 emissions at the microforms. In contrast, the longer-term drainage and deeper water level at the drained site resulted in the replacement of mosses with vascular plants (shrubs) on the hummocks and lichen in the hollows leading to the highest CO2 uptake at the drained hummocks and significant losses in the hollows. The tree NPP (including above- and below-ground growth and litter fall) in 2011 and 2012 was significantly higher at the drained site (92 and 83 g C m-2) than at the experimental (58 and 55 g C m-2) and control (52 and 46 g C m-2) sites. We also quantified the impact of climatic warming at all water table treatments by equipping additional plots with open-top chambers (OTCs) that caused a passive warming on average of ~ 1 °C and differential air warming of ~ 6 °C at midday full sun over the study years. Warming significantly enhanced shrub growth and the CO2 sink function of the drained hummocks (exceeding the cumulative respiration losses in hollows induced by the lowered water level × warming). There was an interaction of water level with warming across hummocks that resulted in the largest net CO2 uptake at the warmed drained hummocks. Thus in 2013, the warming treatment enhanced the sink function of the control site by 13 g m-2, reduced the source function of the experimental by 10 g m-2 and significantly enhanced the sink function of the drained site by 73 g m-2. Therefore, drying and warming in continental bogs is expected to initially accelerate CO2-C losses via ecosystem respiration, but persistent drought and warming is expected to restore the peatland's original CO2-C sink function as a result of the shifts in vegetation composition and productivity between the microforms and increased NPP of trees over time.

Targeting homeostasis in drug delivery using bioresponsive hydrogel microforms.

PubMed

Wilson, A Nolan; Guiseppi-Elie, Anthony

2014-01-30

A drug delivery platform comprising a biocompatible, bioresponsive hydrogel and possessing a covalently tethered peptide-drug conjugate was engineered to achieve stasis, via a closed control loop, of the external biochemical activity of the actuating protease. The delivery platform contains a peptide-drug conjugate covalently tethered to the hydrogel matrix, which in the presence of the appropriate protease, was cleaved and the drug released into the bathing environment. This platform was developed and investigated in silico using a finite element modeling (FEM) approach. Firstly, the primary governing phenomena guiding drug release profiles were investigated, and it was confirmed that under transport-limited conditions, the diffusion of the enzyme within the hydrogel and the coupled enzyme kinetics accurately model the system and are in agreement with published results. Secondly, the FEM model was used to investigate the release of a competitive protease inhibitor, MAG283, via cleavage of Acetyl-Pro-Leu-Gly|Leu-MAG-283 by MMP9 in order to achieve targeted homeostasis of MMP-9 activity, such as in the pathophysiology of chronic wounds, via closed-loop feedback control. The key engineering parameters for the delivery device are the radii of the hydrogel microspheres and the concentration of the peptide-inhibitor conjugate. Homeostatic drug delivery, where the focus turns away from the drug release rate and turns toward achieving targeted control of biochemical activity within a biochemical pathway, is an emerging approach in drug delivery methodologies for which the potential has not yet been fully realized. Copyright © 2013 Elsevier B.V. All rights reserved.

Boreal peatland pools C release: implication for the contemporary C exchange

NASA Astrophysics Data System (ADS)

Pelletier, L.; Strachan, I. B.; Garneau, M.; Roulet, N. T.

2013-12-01

Peatland ecosystems are considered to be net-sinks for carbon, with long-term accumulation rates ranging between 3 and 71 g C m-2 yr-1. However, the net carbon exchange rates vary significantly across the surface of these ecosystems, both in terms of magnitude and direction of the fluxes. Boreal peatlands are characterized by microforms ranging from dry hummocks, to lawns, to wet hollows and pools, which have distinct physical and chemical properties. While the hummocks and lawns absorb C due to the positive balance between gross primary production (CO2 uptake) and respiration (CO2 and CH4 release), pools represent net sources of carbon to the atmosphere. Annual pool C fluxes have been poorly documented and their contribution to the ecosystem level C budget is often ignored, even if they cover a significant portion of the peatland surface. Furthermore, the net ecosystem CO2 exchange (NEE) of these peatlands remains largely unknown. In this study, we examine the dynamics of the atmospheric exchange of CO2 and CH4 from peatland pools. Dissolved CO2 and CH4 were measured sporadically in five pools using the headspace technique and continuously with an NDIR sensor (CO2 for one pool only) over a 16-month period. Fluxes were calculated using the thin boundary layer model. We measured spring release and growing season (May to October) NEE-CO2 and CH4 fluxes in the same peatland using an eddy covariance tower to see how the presence of pools impacts the contemporary C exchange at the ecosystem level.

Practical Repair Method for Unilateral Cleft Lips: Straight-Line Advanced Release Technique.

PubMed

Baek, Rong-Min; Choi, Jun-Ho; Kim, Baek-Kyu

2016-04-01

Straight-line closure repair of unilateral cleft lips was first introduced in the 1840s, and since then, many different techniques have been attempted for cleft repair. However, these methods have several disadvantages and are difficult to adopt. In this study, we describe our novel technique, known as Straight-Line Advanced Release Technique (StART), and its application in treating several cases of unilateral cleft lip. The preoperative design of the surgical method is drawn on the skin, the vermilion, and the oral mucosa. A total of 13 points are marked (points 0-12). The A flap, B flap, triangular flap, M (medial mucosal) flap, and L (lateral mucosal) flap are designed. After completion of the preoperative marking, the wide dissection is performed to separate the orbicularis oris muscle completely from the abnormally inserted bony structure and the enveloped skin-mucosal flap. The freed orbicularis oris muscle is then reconstructed with full width. After all planes of the lip wound are closed, a straight vertical skin suture line is achieved without any unnecessary transverse scar. Unilateral cleft lip repair using StART was conducted in 145 patients between 1993 and 2012. Cases of microform cleft lip were excluded. A total of 21 patients (14%) required a secondary operation on the lip after the first unilateral cheiloplasty. In all patients, satisfactory surgical outcomes were obtained with an indistinct straight-lined scar and a well-aligned lip contour. To acquire a natural and balanced shape in unilateral cleft lip repair, we recommend the novel StART.

Examining boreal peatland vulnerability to wildfire: a cross-scale perspective (Invited)

NASA Astrophysics Data System (ADS)

Thompson, D. K.; Waddington, J. M.; Parisien, M.; Simpson, B. N.; Morris, P. J.; Kettridge, N.

2013-12-01

The contemporary state of peatlands in boreal western Canada is largely a reflection of the equilibrium between peat accumulation and a natural wildfire disturbance regime. However, additional disturbances of climate change and direct anthropogenic impacts are compounding natural wildfire disturbance, leading to the potential of more severe fire and in cases complete ecosystem shifts away from peatlands altogether. Here we present a cross-scale perspective on the vulnerability of peatlands to wildfire in the context of cumulative anthropogenic impacts. At the plot scale, laboratory burning and modelling has identified the exposure of high density humified peat at the surface as being more vulnerable to deep combustion compared to low-density features such as hummock microforms. At the stand scale, studies of tree impacts on moss light availability has identified critically high tree densities where combustion-resistant Sphagnum mosses are out-competed by drier and more flammable feathermosses. Widespread resource development has created seismic lines, cutlines, and associated linear disturbances at densities approaching 1.5 km km-2 in some areas. Our modelling of wind and solar radiation across varying linear disturbance widths and canopy heights reveals increased risk of wildfire ignition and spread at specific width-height ratios. Regionally, we show that streamflow observations can offer insight into drought and seasonal wildfire risk in peatland-dominated portions of the boreal plain. Integrated wildfire management in the boreal forest can benefit from the inclusion of these cross-scale processes and feedbacks we have identified when balancing the often competing interests of ecosystem integrity, economics, and community protection.

Fabrication of wear-resistant silicon microprobe tips for high-speed surface roughness scanning devices

NASA Astrophysics Data System (ADS)

Wasisto, Hutomo Suryo; Yu, Feng; Doering, Lutz; Völlmeke, Stefan; Brand, Uwe; Bakin, Andrey; Waag, Andreas; Peiner, Erwin

2015-05-01

Silicon microprobe tips are fabricated and integrated with piezoresistive cantilever sensors for high-speed surface roughness scanning systems. The fabrication steps of the high-aspect-ratio silicon microprobe tips were started with photolithography and wet etching of potassium hydroxide (KOH) resulting in crystal-dependent micropyramids. Subsequently, thin conformal wear-resistant layer coating of aluminum oxide (Al2O3) was demonstrated on the backside of the piezoresistive cantilever free end using atomic layer deposition (ALD) method in a binary reaction sequence with a low thermal process and precursors of trimethyl aluminum and water. The deposited Al2O3 layer had a thickness of 14 nm. The captured atomic force microscopy (AFM) image exhibits a root mean square deviation of 0.65 nm confirming the deposited Al2O3 surface quality. Furthermore, vacuum-evaporated 30-nm/200-nm-thick Au/Cr layers were patterned by lift-off and served as an etch mask for Al2O3 wet etching and in ICP cryogenic dry etching. By using SF6/O2 plasma during inductively coupled plasma (ICP) cryogenic dry etching, micropillar tips were obtained. From the preliminary friction and wear data, the developed silicon cantilever sensor has been successfully used in 100 fast measurements of 5- mm-long standard artifact surface with a speed of 15 mm/s and forces of 60-100 μN. Moreover, the results yielded by the fabricated silicon cantilever sensor are in very good agreement with those of calibrated profilometer. These tactile sensors are targeted for use in high-aspect-ratio microform metrology.

A new generation of ultra-dense optical I/O for silicon photonics

NASA Astrophysics Data System (ADS)

Wlodawski, Mitchell S.; Kopp, Victor I.; Park, Jongchul; Singer, Jonathan; Hubner, Eric E.; Neugroschl, Daniel; Chao, Norman; Genack, Azriel Z.

2014-03-01

In response to the optical packaging needs of a rapidly growing silicon photonics market, Chiral Photonics, Inc. (CPI) has developed a new generation of ultra-dense-channel, bi-directional, all-optical, input/output (I/O) couplers that bridge the data transport gap between standard optical fibers and photonic integrated circuits. These couplers, called Pitch Reducing Optical Fiber Arrays (PROFAs), provide a means to simultaneously match both the mode field and channel spacing (i.e. pitch) between an optical fiber array and a photonic integrated circuit (PIC). Both primary methods for optically interfacing with PICs, via vertical grating couplers (VGCs) and edge couplers, can be addressed with PROFAs. PROFAs bring the signal-carrying cores, either multimode or singlemode, of many optical fibers into close proximity within an all-glass device that can provide low loss coupling to on-chip components, including waveguides, gratings, detectors and emitters. Two-dimensional (2D) PROFAs offer more than an order of magnitude enhancement in channel density compared to conventional one-dimensional (1D) fiber arrays. PROFAs can also be used with low vertical profile solutions that simplify optoelectronic packaging while reducing PIC I/O real estate usage requirements. PROFA technology is based on a scalable production process for microforming glass preform assemblies as they are pulled through a small oven. An innovative fiber design, called the "vanishing core," enables tailoring the mode field along the length of the PROFA to meet the coupling needs of disparate waveguide technologies, such as fiber and onchip. Examples of single- and multi-channel couplers fabricated using this technology will be presented.

Three-dimensional facies architecture of the Salem Limestone (middle Mississippian), Eastern Margin of Illinois basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nadeem, A.; Keith, B.D.; Thompson, T.A.

Mapping of sedimentary surfaces in the Middle Mississippian Salem Limestone exposed on sawed quarry walls in south-central Indiana has revealed a hierarchy of depositional units representative of the extremely dynamic hydrographic regime of the upper shoreface zone. The depositional units on the scale of microform and mesoform are represented by the microfacies and the facies respectively. Based on their hierarchy, genetically related depositional units and associated bounding surfaces were grouped together to construct four architectural packages (APs) of the scale of mesoforms. AP-I is dominantly an echinoderm- and bryozoan-rich grainstone and consists of bedforms ranging from small ripples bounded bymore » first-order surfaces to two- and three- dimensional megaripples bounded by the second-order surfaces. It formed as part of a giant ramp (asymmetric wavefield) within the intrashoal channel setting. AP-II, also a skeletal grainstone, is a complex of giant sandwaves that moved into the area under the infulence of a storm and partly filled the basal channel form of AP-I. Large avalanche foresets with tangential toesets prevail. AP-III is a dark-gray spatially discontinuous skeletal grainstone to packstone that laterally grades into a skeletal packstone to wackestone. It locally developed overhangs, rips-ups, and hardground on its upper surface. AP-IV is a skeletal and oolitic grainstone formed of tabular two-dimensional megaripples (planar cross-beds) and three-dimensional oscillatory megaripples (trough cross-beds). These architectural packages based on the bedform architecture and micro-and mesoscale compositional changes can be used to characterize micro-, meso, and macroscale heterogeneities. Models of facies architecture from this and similar outcrop studies can be applied to the subsurface Salem reservoirs in the Illinois Basin using cores.« less

A Longitudinal Study of the Presence of Dental Anomalies in the Primary and Permanent Dentitions of Cleft Lip and/or Palate Patients.

PubMed

Suzuki, Akira; Nakano, Masayuki; Yoshizaki, Keigo; Yasunaga, Atsushi; Haruyama, Naoto; Takahashi, Ichiro

2017-05-01

  The aim is to survey primary and permanent dental anomalies: hypodontia, microdontia, a supernumerary tooth, and fused teeth in patients with cleft lip and/or palate.   Retrospective longitudinal study Subjects :  The subjects were selected from all 1724 patients with cleft lip and/or palate who were registered at the orthodontic clinic of Kyushu University Hospital, Fukuoka, Japan, from 1970 to 2009. Finally, 994 subjects were evaluated for primary dentition, 1352 for permanent dentition, and 871 for the longitudinal changes from primary to permanent dentition.   The prevalence of dental anomalies was compared for each tooth type, among various cleft types, between males and females, and between the alveolar cleft area and the noncleft area.   The prevalence of hypodontia was 16.2% for primary dentition and 52.7% for permanent dentition in the subjects with cleft lip and/or palate. Hypodontia increased with the severity of the cleft type. Multiple hypodontia was found more frequently in the subjects with bilateral cleft lip and palate and the subjects with unilateral cleft lip and palate. Microformed lateral incisors were found in 22.7% of permanent lateral incisors but not in primary dentition. Supernumerary teeth were found in 17.7% of the subjects with cleft lip and/or palate for primary maxillary dentition and in 5.7% for permanent maxillary dentition.   The prevalence of hypodontia was greater in permanent dentition than in primary dentition; although, it was not much different between males and females or between the right and left sides. The prevalence of dental anomalies was significantly different among four groups by cleft type: cleft lip, cleft lip and alveolus, cleft lip and palate, and cleft palate.

One-Stage versus Two-Stage Repair of Asymmetric Bilateral Cleft Lip: A 20-Year Retrospective Study of Clinical Outcome.

PubMed

Chung, Kyung Hoon; Lo, Lun-Jou

2018-05-01

Both one- and two-stage approaches have been widely used for patients with asymmetric bilateral cleft lip. There are insufficient long-term outcome data for comparison of these two methods. The purpose of this retrospective study was to compare the clinical outcome over the past 20 years. The senior author's (L.J.L.) database was searched for patients with asymmetric bilateral cleft lip from 1995 to 2015. Qualified patients were divided into two groups: one-stage and two-stage. The postoperative photographs of patients were evaluated subjectively by surgical professionals and laypersons. Ratios of the nasolabial region were calculated for objective analysis. Finally, the revision procedures in the nasolabial area were reviewed. Statistical analyses were performed. A total of 95 consecutive patients were qualified for evaluation. Average follow-up was 13.1 years. A two-stage method was used in 35 percent of the patients, and a one-stage approach was used in 65 percent. All underwent primary nasal reconstruction. Among the satisfaction rating scores, the one-stage repair was rated significantly higher than two-stage reconstruction (p = 0.0001). Long-term outcomes of the two-stage patients and the unrepaired mini-microform deformities were unsatisfactory according to both professional and nonprofessional evaluators. The revision rate was higher in patients with a greater-side complete cleft lip and palate as compared with those without palatal involvement. The results suggested that one-stage repair provided better results with regard to achieving a more symmetric and smooth lip and nose after primary reconstruction. The revision rate was slightly higher in the two-stage patient group. Therapeutic, III.

Ecology of testate amoebae in an Amazonian peatland and development of a transfer function for palaeohydrological reconstruction.

PubMed

Swindles, Graeme T; Reczuga, Monika; Lamentowicz, Mariusz; Raby, Cassandra L; Turner, T Edward; Charman, Dan J; Gallego-Sala, Angela; Valderrama, Elvis; Williams, Christopher; Draper, Frederick; Honorio Coronado, Euridice N; Roucoux, Katherine H; Baker, Tim; Mullan, Donal J

2014-08-01

Tropical peatlands represent globally important carbon sinks with a unique biodiversity and are currently threatened by climate change and human activities. It is now imperative that proxy methods are developed to understand the ecohydrological dynamics of these systems and for testing peatland development models. Testate amoebae have been used as environmental indicators in ecological and palaeoecological studies of peatlands, primarily in ombrotrophic Sphagnum-dominated peatlands in the mid- and high-latitudes. We present the first ecological analysis of testate amoebae in a tropical peatland, a nutrient-poor domed bog in western (Peruvian) Amazonia. Litter samples were collected from different hydrological microforms (hummock to pool) along a transect from the edge to the interior of the peatland. We recorded 47 taxa from 21 genera. The most common taxa are Cryptodifflugia oviformis, Euglypha rotunda type, Phryganella acropodia, Pseudodifflugia fulva type and Trinema lineare. One species found only in the southern hemisphere, Argynnia spicata, is present. Arcella spp., Centropyxis aculeata and Lesqueresia spiralis are indicators of pools containing standing water. Canonical correspondence analysis and non-metric multidimensional scaling illustrate that water table depth is a significant control on the distribution of testate amoebae, similar to the results from mid- and high-latitude peatlands. A transfer function model for water table based on weighted averaging partial least-squares (WAPLS) regression is presented and performs well under cross-validation (r(2)(apparent)= 0.76, RMSE = 4.29; r(2)(jack)= 0.68, RMSEP =5.18). The transfer function was applied to a 1-m peat core, and sample-specific reconstruction errors were generated using bootstrapping. The reconstruction generally suggests near-surface water tables over the last 3,000 years, with a shift to drier conditions at c. cal. 1218-1273 AD.

Applicability of Unmanned Aerial Vehicles in Research on Aeolian Processes

NASA Astrophysics Data System (ADS)

Algimantas, Česnulevičius; Artūras, Bautrėnas; Linas, Bevainis; Donatas, Ovodas; Kęstutis, Papšys

2018-02-01

Surface dynamics and instabilities are characteristic of aeolian formation. The method of surface comparison is regarded as the most appropriate one for evaluation of the intensity of aeolian processes and the amount of transported sand. The data for surface comparison can be collected by topographic survey measurements and using unmanned aerial vehicles. Time cost for relief microform fixation and measurement executing topographic survey are very high. The method of unmanned aircraft aerial photographs fixation also encounters difficulties because there are no stable clear objects and contours that enable to link aerial photographs, to determine the boundaries of captured territory and to ensure the accuracy of surface measurements. Creation of stationary anchor points is irrational due to intense sand accumulation and deflation in different climate seasons. In September 2015 and in April 2016 the combined methodology was applied for evaluation of intensity of aeolian processes in the Curonian Spit. Temporary signs (marks) were installed on the surface, coordinates of the marks were fixed using GPS and then flight of unmanned aircraft was conducted. The fixed coordinates of marks ensure the accuracy of measuring aerial imagery and the ability to calculate the possible corrections. This method was used to track and measure very small (micro-rank) relief forms (5-10 cm height and 10-20 cm length). Using this method morphometric indicators of micro-terraces caused by sand dunes pressure to gytia layer were measured in a non-contact way. An additional advantage of the method is the ability to accurately link the repeated measurements. The comparison of 3D terrain models showed sand deflation and accumulation areas and quantitative changes in the terrain very clearly.

Interpreting Carbon Fluxes from a Spatially Heterogeneous Peatland with Thawing Permafrost: Scaling from Plant Community Scale to Ecosystem Scale

NASA Astrophysics Data System (ADS)

Harder, S. R.; Roulet, N. T.; Strachan, I. B.; Crill, P. M.; Persson, A.; Pelletier, L.; Watt, C.

2014-12-01

Various microforms, created by spatial differential thawing of permafrost, make up the subarctic heterogeneous Stordalen peatland complex (68°22'N, 19°03'E), near Abisko, Sweden. This results in significantly different peatland vegetation communities across short distances, as well as differences in wetness, temperature and peat substrates. We have been measuring the spatially integrated CO2, heat and water vapour fluxes from this peatland complex using eddy covariance and the CO2 exchange from specific plant communities within the EC tower footprint since spring 2008. With this data we are examining if it is possible to derive the spatially integrated ecosystem-wide fluxes from community-level simple light use efficiency (LUE) and ecosystem respiration (ER) models. These models have been developed using several years of continuous autochamber flux measurements for the three major plant functional types (PFTs) as well as knowledge of the spatial variability of the vegetation, water table and active layer depths. LIDAR was used to produce a 1 m resolution digital evaluation model of the complex and the spatial distribution of PFTs was obtained from concurrent high-resolution digital colour air photography trained from vegetation surveys. Continuous water table depths have been measured for four years at over 40 locations in the complex, and peat temperatures and active layer depths are surveyed every 10 days at more than 100 locations. The EC footprint is calculated for every half-hour and the PFT based models are run with the corresponding environmental variables weighted for the PFTs within the EC footprint. Our results show that the Sphagnum, palsa, and sedge PFTs have distinctly different LUE models, and that the tower fluxes are dominated by a blend of the Sphagnum and palsa PFTs. We also see a distinctly different energy partitioning between the fetches containing intact palsa and those with thawed palsa: the evaporative efficiency is higher and the Bowen ration lower for the thawed palsa fetches.

A simple objective method for determining a dynamic journal collection.

PubMed

Bastille, J D; Mankin, C J

1980-10-01

In order to determine the content of a journal collection responsive to both user needs and space and dollar constraints, quantitative measures of the use of a 647-title collection have been related to space and cost requirements to develop objective criteria for a dynamic collection for the Treadwell Library at the Massachusetts General Hospital, a large medical research center. Data were collected for one calendar year (1977) and stored with the elements for each title's profile in a computerized file. To account for the effect of the bulk of the journal runs on the number of uses, raw use data have been adjusted using linear shelf space required for each title to produce a factor called density of use. Titles have been ranked by raw use and by density of use with space and cost requirements for each. Data have also been analyzed for five special categories of use. Given automated means of collecting and storing data, use measures should be collected continuously. Using raw use frequency ranking to relate use to space and costs seems sensible since a decision point cutoff can be chosen in terms of the potential interlibrary loans generated. But it places new titles at risk while protecting titles with long, little used runs. Basing decisions on density of use frequency ranking seems to produce a larger yield of titles with fewer potential interlibrary loans and to identify titles with overlong runs which may be pruned or converted to microform. The method developed is simple and practical. Its design will be improved to apply to data collected in 1980 for a continuous study of journal use. The problem addressed is essentially one of inventory control. Viewed as such it makes good financial sense to measure use as part of the routine operation of the library to provide information for effective management decisions.

A Simple Objective Method for Determining a Dynamic Journal Collection *†

PubMed Central

Bastille, Jacqueline D.; Mankin, Carole J.

1980-01-01

In order to determine the content of a journal collection responsive to both user needs and space and dollar constraints, quantitative measures of the use of a 647-title collection have been related to space and cost requirements to develop objective criteria for a dynamic collection for the Treadwell Library at the Massachusetts General Hospital, a large medical research center. Data were collected for one calendar year (1977) and stored with the elements for each title's profile in a computerized file. To account for the effect of the bulk of the journal runs on the number of uses, raw use data have been adjusted using linear shelf space required for each title to produce a factor called density of use. Titles have been ranked by raw use and by density of use with space and cost requirements for each. Data have also been analyzed for five special categories of use. Given automated means of collecting and storing data, use measures should be collected continuously. Using raw use frequency ranking to relate use to space and costs seems sensible since a decision point cutoff can be chosen in terms of the potential interlibrary loans generated. But it places new titles at risk while protecting titles with long, little used runs. Basing decisions on density of use frequency ranking seems to produce a larger yield of titles with fewer potential interlibrary loans and to identify titles with overlong runs which may be pruned or converted to microform. The method developed is simple and practical. Its design will be improved to apply to data collected in 1980 for a continuous study of journal use. The problem addressed is essentially one of inventory control. Viewed as such it makes good financial sense to measure use as part of the routine operation of the library to provide information for effective management decisions. PMID:7437589

Effects of experimental warming and elevated CO2 on surface methane and CO­2 fluxes from a boreal black spruce peatland

NASA Astrophysics Data System (ADS)

Gill, A. L.; Finzi, A.; Hsieh, I. F.; Giasson, M. A.

2016-12-01

High latitude peatlands represent a major terrestrial carbon store sensitive to climate change, as well as a globally significant methane source. While elevated atmospheric carbon dioxide concentrations and warming temperatures may increase peat respiration and C losses to the atmosphere, reductions in peatland water tables associated with increased growing season evapotranspiration may alter the nature of trace gas emission and increase peat C losses as CO2 relative to methane (CH4). As CH4 is a greenhouse gas with twenty times the warming potential of CO2, it is critical to understand how surface fluxes of CO2 and CH4 will be influenced by factors associated with global climate change. We used automated soil respiration chambers to assess the influence of elevated atmospheric CO2 and whole ecosystem warming on peatland CH4 and CO2 fluxes at the SPRUCE (Spruce and Peatland Responses Under Climatic and Environmental Change) Experiment in northern Minnesota. Here we report soil iCO2 and iCH4 flux responses to the first year of belowground warming and the first season of whole ecosystem warming and elevated CO2 treatments. We find that peat methane fluxes are more sensitive to warming treatments than peat CO2 fluxes, particularly in hollow peat microforms. Surface CO2:CH4 flux ratios decreased across warming treatments, suggesting that the temperature sensitivity of methane production overshadows the effect of peat drying and surface aeration in the short term. δ13C of the emitted methane was more depleted in the early and late growing season, indicating a transition from hydrogenotrophic to acetoclastic methanogenesis during periods of high photosynthetic input. The measurement record demonstrates that belowground warming has measureable impacts on the nature of peat greenhouse gas emission within one year of treatment.

CO2 and CH4 fluxes of contrasting pristine bogs in southern Patagonia (Tierra del Fuego, Argentina)

NASA Astrophysics Data System (ADS)

Münchberger, Wiebke; Blodau, Christian; Kleinebecker, Till; Pancotto, Veronica

2015-04-01

South Patagonian peatlands cover a wide range of the southern terrestrial area and thus are an important component of the terrestrial global carbon cycle. These extremely southern ecosystems have been accumulating organic material since the last glaciation up to now and are - in contrast to northern hemisphere bogs - virtually unaffected by human activities. So far, little attention has been given to these pristine ecosystems and great carbon reservoirs which will potentially be affected by climate change. We aim to fill the knowledge gap in the quantity of carbon released from these bogs and in what controls their fluxes. We study the temporal and spatial variability of carbon fluxes in two contrasting bog ecosystems in southern Patagonia, Tierra del Fuego. Sphagnum-dominated bog ecosystems in Tierra del Fuego are similar to the ones on the northern hemisphere, while cushion plant-dominated bogs can almost exclusively be found in southern Patagonia. These unique cushion plant-dominated bogs are found close to the coast and their occurrence changes gradually to Sphagnum-dominated bogs with increasing distance from the coast. We conduct closed chamber measurements and record relevant environmental variables for CO2 and CH4 fluxes during two austral vegetation periods from December to April. Chamber measurements are performed on microforms representing the main vegetation units of the studied bogs. Gas concentrations are measured with a fast analyzer (Los Gatos Ultraportable Greenhouse Gas Analyzer) allowing to accurately record CH4 fluxes in the ppm range. We present preliminary results of the carbon flux variability from south Patagonian peat bogs and give insights into their environmental controls. Carbon fluxes of these two bog types appear to be highly different. In contrast to Sphagnum-dominated bogs, cushion plant-dominated bogs release almost no CH4 while their CO2 flux in both, photosynthesis and respiration, can be twice as high as for Sphagnum-dominated bogs. Water table fluctuations in the cushion plant-dominated bog seem to be negligible and CH4 is mainly released from Sphagnum lawns suggesting the importance of the vegetation type for CH4 fluxes in these special ecosystems. Our results will help to understand which conditions favor the development of either a cushion plant-dominated or Sphagnum-dominated bog which is not yet known.

Weathering landforms exposure and erosion phases in Pedriza de Manzanares (Spanish Central Range)

NASA Astrophysics Data System (ADS)

García-Rodríguez, M.; Centeno Carrillo, J. D.; Alvarez de Buergo, M.

2012-04-01

The phases of erosion can be reconstructed measuring the position and dimensions of exposed granite underground weathering landforms. We afford a first approach of this kind of "erosion history" in the area of Pedriza de Manzanares. Pedriza de Manzanares is the main part of the Natural Park of High Manzanares River Basin. The area is part also of the Late Paleozoic granites of the Spanish Central Range, intruded during the Variscan orogeny, and uplifted to its present position during Alpine orogeny. The granite shows a complex fracture pattern (related to Variscan and Alpine processes) that defines a landscape with alternance of regolith-connected-depressions and fresh granite outcrops with abundant bornhards and boulders. Pedriza (as most people call it) is a well known area for its granite landforms which attract tourism, educators and rock climbers. In this area, the contrasting hydrological behaviour of fresh and weathered granite, especially in fractures areas, produces small aquifers with a high recharge from adjacent impermeable surfaces. These conditions have been studied in relation to the soil water availability (for both human and ecosystems), and in relation to the geomorphic edaphic processes (taffoni, flared slopes, etc.). In previous works (García et al., 2008, Centeno et al., 2010) a conceptual model using MS-Excel was devised which provided the basis by which were defined the relevant variables and their interconnections (landforms, climate, hydrogeology). From the standpoint of soils water (and the related weathering processes or ecosystem characteristics), this is especially important in semi-arid and arid climates, as has been appreciated by practising farmers for many years, for the contrast in productive potential in stark between the regolithic and rocky areas. At the same time, granite weathering is enhanced by the persistent presence of water in the regolith and, as a consequence, many microforms are initiated or evolve under the regolith -something well known from the work by Twidale and Borne (1975) and Twidale (2002) when they studied the episodic exposure of these landforms. Now, we can identify some correlation between variables like taffoni's magnitude, regolith-outcrop ratio and taffoni organization in levels. In addition, these levels of taffoni allow us to identify several phases of regolith erosion in most regolith unit, in different settings and altitudes. Centeno, J.D., García Rodríguez, M. and Moya Palomares, M.E. (2010). Influence of granite landforms on water balance in semi-arid and humid climates. Cadernos Lab. Xeolóxico de Laxe. Coruña 35, 99-108 García Rodríguez, M., Centeno, J.D. and De Pablo, M.A. (2008). Relieve y agua en regiones graníticas: un modelo cuantitativo con aplicaciones en la gestión del agua y la geodiversidad. M+A Revista Electrónic@ de Medioambiente. UCM. Vol. 5: 26-40. Twidale, C.R. and Bourne, J.A. (1975). Episodic exposure of inselbergs. Geological Society of America Bulletin, 86: 1473-1481. Twidale, C.R. (2002). The two-stage concept of landform and landscape development involving etching: origin, development and implications of an idea. Earth-Science Reviews, 57 (1-2): 37-74.

Methane and CO2 fluxes from peat soil, palm stems and field drains in two oil palm plantations in Sarawak, Borneo, on different tropical peat soil types.

NASA Astrophysics Data System (ADS)

Manning, Frances; Lip Khoon, Kho; Hill, Tim; Arn Teh, Yit

2017-04-01

Oil palm plantations have been expanding rapidly on tropical peat soils in the last 20 years, with 50 % of SE Asian peatlands now managed as industrial or small-holder plantations, up from 11% in 1990. Tropical peat soils are an important carbon (C) store, containing an estimated 17 % of total peatland C. There are large uncertainties as to the soil C dynamics in oil palm plantations on peat due to a shortage of available data. It is therefore essential to understand the soil C cycle in order to promote effective management strategies that optimise yields, whilst maintaining the high C storage capacity of the soil. Here we present CO2 and CH4 fluxes from two oil palm plantations in Sarawak, Malaysia on peat soils. Data were collected from different surface microforms within each plantation that experienced different surface management practices. These included the area next to the palm, in bare soil harvest paths, beneath frond piles, underneath cover crops, from the surface of drains, and from palm stems. Data were collected continuously over one year and analysed with different environmental variables, including soil temperature, WTD, O2, soil moisture and weather data in order to best determine the constraints on the dataset. Total soil respiration (Rtot) varied between 0.09 and 1.59 g C m-2 hr-1. The largest fluxes (0.59 - 1.59 g C m-2 hr-1) were measured next to the palms. Larger CO2 fluxes were observed beneath the cover crops than in the bare soil. This trend was attributed to priming effects from the input of fresh plant litter and exudates. Peat soil type was shown to have significantly different fluxes. The different plantations also had different environmental drivers best explaining the variation in Rtot - with soil moisture being the most significant variable on Sabaju series soil and soil temperature being the most significant environmental variable in the plantation with the Teraja series soil. Rtot was shown to reduce significantly with increasing distance from the palm. The relationship between Rtot and root biomass, which also decreased significantly with increasing distance from the palm, allowed for the partitioning of Rtot into peat oxidation and Ra. Here rates of peat oxidation were estimated to be 0.11 g C m-2 hr-1 following partitioning, and 0.16 g C m-2 hr-1 without partitioning. Methane fluxes varied between 0 and 1.95 g C m-2 hr-1. The largest methane fluxes were emitted from collection drains. Methane oxidation was occasionally observed in field drains, when the water table dropped below the depth of the drain. Soil methane fluxes were lower than those from collection drains. The highest methane fluxes were observed next to palms (0.02 mg C m-2 hr-1) and the lowest under frond piles (0.08 mg C m-2 hr-1). Methane emissions were measured from the palm stems. Preliminary data gives a range between 0.005 and 0.27 µg C m-2 hr-1. These results show wide ranges in both CO2 and CH4 emissions from different sources within the plantations, with the collection drains being the largest source of C fluxes.