Vermistabilization of textile mill sludge spiked with poultry droppings by an epigeic earthworm Eisenia foetida.

PubMed

Garg, V K; Kaushik, Priya

2005-06-01

Investigations were made to explore the potential of an epigeic earthworm Eisenia foetida to transform textile mill sludge spiked with poultry droppings in to value added product, i.e., vermicompost. The growth and reproduction of E. foetida was monitored in a range of different feed mixtures for 77 days in the laboratory under controlled experimental conditions. The maximum growth was recorded in 100% cow dung (CD). Replacement of poultry droppings by cow dung in feed mixtures and vice versa had little or no effect on worm growth rate and reproduction potential. Worms grew and reproduced favourably in 70% poultry droppings (PD)+30% solid textile mill sludge (STMS) and 60% PD+40% STMS feed mixtures. Greater percentage of STMS in the feed mixture significantly affected the biomass gain and cocoon production. Net weight gain by earthworms in 100% CD was 2.9-18.2 fold higher than different STMS containing feed mixtures. The mean number of cocoon production was between 23.4+/-4.65 (in 100% CD) and 3.6+/-1.04 (in 50% PD+50% STMS) cocoons earthworm(-1) for different feed mixtures tested. Vermicomposting resulted in significant reduction in C:N ratio and increase in nitrogen and phosphorus contents. Total potassium, total calcium and heavy metals (Fe, Zn, Pb and Cd) contents were lower in the final product than initial feed mixtures. Our trials demonstrated vermicomposting as an alternate technology for the recycling and environmentally safe disposal/management of textile mill sludge using an epigeic earthworm E. foetida if mixed with poultry droppings.

Dynamics of biological and chemical parameters during vermicomposting of solid textile mill sludge mixed with cow dung and agricultural residues.

PubMed

Kaushik, Priya; Garg, V K

2004-09-01

In India, thousands of tons of textile mill sludge are produced every year. We studied the ability of epigeic earthworm Eisenia foetida to transform textile mill sludge mixed with cow dung and/or agricultural residues into value added product, i.e., vermicompost. The growth, maturation, mortality, cocoon production, hatching success and the number of hatchlings were monitored in a range of different feed mixtures for 11 weeks in the laboratory under controlled environmental conditions. The maximum growth and reproduction was obtained in 100% cow dung, but worms grew and reproduced favorably in 80% cow dung + 20% solid textile mill sludge and 70% cow dung + 30% solid textile mill sludge also. Addition of agricultural residues had adverse effects on growth and reproduction of worms. Vermicomposting resulted in significant reduction in C:N ratio and increase in TKN, TP, TK and TCa after 77 days of worm activity in all the feeds. Vermicomposting can be an alternate technology for the management of textile mill sludge if mixed with cow dung in appropriate quantities. Copyright 2003 Elsevier Ltd.

An on-belt elemental analyser for the cement industry.

PubMed

Lim, C S; Tickner, J R; Sowerby, B D; Abernethy, D A; McEwan, A J; Rainey, S; Stevens, R; Manias, C; Retallack, D

2001-01-01

On-line control of raw mill feed composition is a key factor in the improved control of cement plants. A new and improved on-conveyor belt elemental analyser for cement raw mill feed based on neutron inelastic scatter and capture techniques has been developed and tested successfully in Adelaide Brighton's Birkenhead cement plant on highly segregated material with a depth range of 100 to 180 mm. Dynamic tests in the plant have shown analyser RMS total errors of 0.49, 0.52, 0.38 and 0.23 wt% (on a loss free basis) for CaO, SiO2, Al2O3 and Fe2O3 respectively, when 10-minute counting periods are used.

Triaxial X-Ray Diffraction Method and its Application to Monitor Residual Stress in Surface Layers after High-Feed Milling

NASA Astrophysics Data System (ADS)

Zaušková, Lucia; Czán, Andrej; Šajgalík, Michal; Pobijak, Jozef; Mikloš, Matej

2017-10-01

High-feed milling is a milling method characteristic with shallow depth of cut and high feed rate to maximize the amount of removed metal from a part, generating residual stresses in the surface and subsurface layers of the machined parts. The residual stress has a large influence on the functional properties of the components. The article is focused on the application of triaxial x-ray diffraction method to monitor residual stresses after high feed milling. Significance of triaxial measuring method is the capability of measuring in different angles so it is possible to acquire stress tensor containing normal and shear stress components.

21 CFR 510.305 - Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing...

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing or containing new animal drugs. 510.305 Section 510...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS Records and Reports § 510.305 Maintenance of...

Estimation of costs for control of Salmonella in high-risk feed materials and compound feed

PubMed Central

Wierup, Martin; Widell, Stig

2014-01-01

Introduction Feed is a potential and major source for introducing Salmonella into the animal-derived food chain. This is given special attention in the European Union (EU) efforts to minimize human food-borne Salmonella infections from animal-derived food. The objective of this study was to estimate the total extra cost for preventing Salmonella contamination of feed above those measures required to produce commercial feed according to EU regulation (EC) No 183/2005. The study was carried out in Sweden, a country where Salmonella infections in food-producing animals from feed have largely been eliminated. Methods On the initiative and leadership of the competent authority, the different steps of feed production associated with control of Salmonella contamination were identified. Representatives for the major feed producers operating in the Swedish market then independently estimated the annual mean costs during the years 2009 and 2010. The feed producers had no known incentives to underestimate the costs. Results and discussion The total cost for achieving a Salmonella-safe compound feed, when such a control is established, was estimated at 1.8–2.3 € per tonne of feed. Of that cost, 25% relates to the prevention of Salmonella contaminated high-risk vegetable feed materials (mainly soybean meal and rapeseed meal) from entering feed mills, and 75% for measures within the feed mills. Based on the feed formulations applied, those costs in relation to the farmers’ 2012 price for compound feed were almost equal for broilers and dairy cows (0.7%). Due to less use of protein concentrate to fatten pigs, the costs were lower (0.6%). These limited costs suggest that previous recommendations to enforce a Salmonella-negative policy for animal feed are realistic and economically feasible to prevent a dissemination of the pathogen to animal herds, their environment, and potentially to human food products. PMID:24959328

21 CFR 510.301 - Records and reports concerning experience with animal feeds bearing or containing new animal...

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Records and reports concerning experience with animal feeds bearing or containing new animal drugs for which an approved medicated feed mill license... containing new animal drugs for which an approved medicated feed mill license application is in effect...

CONTROL FOR ROLLING MILL

DOEpatents

Shuck, A.B.; Shaw, W.C.

1961-06-20

A plutonium-rolling apparatus is patented that has two sets of feed rolls, shaping rolls between the feed rolls, and grippers beyond the feed rolls, which ready a workpiece for a new pass through the shaping rolls by angularly shifting the workpiece about its axis or transversely moving it on a line parallel to the axes of the shaping rolls. Actuation of each gripper for gripping or releasing the workpiece is produced by the relative positions assumed by the feed rolls adjacent to the gripper as the workpiece enters or leaves the feed rolls.

Direct measures of mechanical energy for knife mill size reduction of switchgrass, wheat straw, and corn stover.

PubMed

Bitra, Venkata S P; Womac, Alvin R; Igathinathane, C; Miu, Petre I; Yang, Yuechuan T; Smith, David R; Chevanan, Nehru; Sokhansanj, Shahab

2009-12-01

Lengthy straw/stalk of biomass may not be directly fed into grinders such as hammer mills and disc refiners. Hence, biomass needs to be preprocessed using coarse grinders like a knife mill to allow for efficient feeding in refiner mills without bridging and choking. Size reduction mechanical energy was directly measured for switchgrass (Panicum virgatum L.), wheat straw (Triticum aestivum L.), and corn stover (Zea mays L.) in an instrumented knife mill. Direct power inputs were determined for different knife mill screen openings from 12.7 to 50.8 mm, rotor speeds between 250 and 500 rpm, and mass feed rates from 1 to 11 kg/min. Overall accuracy of power measurement was calculated to be +/-0.003 kW. Total specific energy (kWh/Mg) was defined as size reduction energy to operate mill with biomass. Effective specific energy was defined as the energy that can be assumed to reach the biomass. The difference is parasitic or no-load energy of mill. Total specific energy for switchgrass, wheat straw, and corn stover chopping increased with knife mill speed, whereas, effective specific energy decreased marginally for switchgrass and increased for wheat straw and corn stover. Total and effective specific energy decreased with an increase in screen size for all the crops studied. Total specific energy decreased with increase in mass feed rate, but effective specific energy increased for switchgrass and wheat straw, and decreased for corn stover at increased feed rate. For knife mill screen size of 25.4 mm and optimum speed of 250 rpm, optimum feed rates were 7.6, 5.8, and 4.5 kg/min for switchgrass, wheat straw, and corn stover, respectively, and the corresponding total specific energies were 7.57, 10.53, and 8.87 kWh/Mg and effective specific energies were 1.27, 1.50, and 0.24 kWh/Mg for switchgrass, wheat straw, and corn stover, respectively. Energy utilization ratios were calculated as 16.8%, 14.3%, and 2.8% for switchgrass, wheat straw, and corn stover, respectively. These data will be useful for preparing the feed material for subsequent fine grinding operations and designing new mills.

Vermiconversion of wastewater sludge from textile mill mixed with anaerobically digested biogas plant slurry employing Eisenia foetida.

PubMed

Garg, V K; Kaushik, Priya; Dilbaghi, Neeraj

2006-11-01

Vermicomposting is commonly used for the management of organic wastes. We have investigated the potential of an epigeic earthworm, Eisenia foetida, to transform solid textile mill sludge (STMS) spiked with anaerobically digested biogas plant slurry (BPS) into vermicompost to evaluate the feasibility of vermicomposting in industries for waste management. The growth and reproduction of E. foetida was monitored in a range of different feed mixtures for 15 weeks in laboratory under controlled experimental conditions. E. foetida did not survive in fresh STMS. But worms grew and reproduced in STMS spiked with BPS feed mixtures. A greater percentage of STMS in feed mixture affected biomass gain and cocoon production by earthworms. The maximum growth was recorded in 100% BPS. The net weight gain by E. foetida in 100% BPS was two-four-fold higher than STMS-containing feed mixtures. After 15 weeks, maximum cocoons (78) were counted in 100% BPS and minimum (26) in 60% BPS+40% STMS feed. Vermicomposting resulted in pH shift toward acidic, significant reduction in C:N ratio, and increase in nitrogen, phosphorus, and potassium contents. Microbial activity measured as dehydrogenase activity increased with time up to day 75 but decreased on day 90, indicating the exhaustion of feed and decrease in microbial activity. These experiments demonstrate that vermicomposting can be an alternate technology for the recycling and environmentally safe disposal/management of textile mill sludge using an epigeic earthworm, E. foetida, if mixed with anaerobically digested BPS in appropriate ratios.

The infrared camera application for calculating the impact of the feed screw thermal expansion on machining accuracy

NASA Astrophysics Data System (ADS)

Matras, A.

2017-08-01

The paper discusses the impact of the feed screw heating on the machining accuracy. The test stand was built based on HASS Mini Mill 2 CNC milling machine and a Flir SC620 infrared camera. Measurements of workpiece were performed on Talysurf Intra 50 Taylor Hobson profilometer. The research proved that the intensive work of the milling machine lasted 60 minutes, causing thermal expansion of the feed screw what influence on the dimension error of the workpiece.

21 CFR 510.305 - Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing...

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing or containing new animal drugs. 510.305 Section 510.305 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...

21 CFR 510.305 - Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing...

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing or containing new animal drugs. 510.305 Section 510.305 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...

21 CFR 510.305 - Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing...

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Maintenance of copies of approved medicated feed mill licenses to manufacture animal feed bearing or containing new animal drugs. 510.305 Section 510.305 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...

Salmonella occurrence and Enterobacteriaceae counts in pig feed ingredients and compound feed from feed mills in Ireland.

PubMed

Burns, Anne Marie; Lawlor, Peadar G; Gardiner, Gillian E; McCabe, Evonne M; Walsh, Des; Mohammed, Manal; Grant, Jim; Duffy, Geraldine

2015-10-01

The purpose of this study was to assess the occurrence of non-typhoidal Salmonellae and Enterobacteriaceae counts in raw ingredients and compound feeds sampled from feed mills manufacturing pig diets. Between November 2012 and September 2013, feed ingredients (n=340) and compound pig feed (n=313) samples were collected from five commercial feed mills and one home compounder at various locations throughout Ireland. Feed ingredients included cereals, vegetable protein sources and by-products of oil extraction and ethanol production. The compound feeds included meal and pelleted feed for all stages of pig production. Samples were analysed for Salmonella using standard enrichment procedures. Recovered isolates were serotyped, characterised for antibiotic resistance and subtyped by multi locus variance analysis (MLVA). Total Enterobacteriaceae counts were also performed. Salmonella was recovered from 2/338 (0.6%) ingredients (wheat and soybean meal), at two of the six mills. Salmonella was also detected in 3/317 (0.95%) compound feeds including pelleted feed which undergoes heat treatment. All isolates recovered from feed ingredient and compound feed samples were verified as Salmonella enterica subsp. enterica serotype (4,[5],12:i:-) that lack the expression of flagellar Phase 2 antigens representing monophasic variants of Salmonella Typhimurium (4,[5],12:i:-). Isolates exhibited resistance to between two and seven antimicrobials. Two distinct MLVA profiles were observed, with the same profile recovered from both feed and ingredients, although these did not originate at the same mill. There was no relationship between the occurrence of Salmonella and a high Enterobacteriaceae counts but it was shown that Enterobacteriaceae counts were significantly lower in pelleted feed (heat treated) than in meal (no heat treatment) and that Enterobacteriaceae counts would be very useful indicator in HACPP programme. Overall, although the prevalence of Salmonella in pig feed and feed ingredients in the present study was low, even minor Salmonella contamination in feed has the potential to affect many herds and may subsequently cause human infection. Furthermore, the recovery of a recently emerged serovar with multi-antibiotic resistance is a potential cause for concern. Copyright © 2015 Elsevier B.V. All rights reserved.

Update of distillers grains displacement ratios for corn ethanol life-cycle analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arora, S.; Wu, M.; Wang, M.

2011-02-01

Production of corn-based ethanol (either by wet milling or by dry milling) yields the following coproducts: distillers grains with solubles (DGS), corn gluten meal (CGM), corn gluten feed (CGF), and corn oil. Of these coproducts, all except corn oil can replace conventional animal feeds, such as corn, soybean meal, and urea. Displacement ratios of corn-ethanol coproducts including DGS, CGM, and CGF were last updated in 1998 at a workshop at Argonne National Laboratory on the basis of input from a group of experts on animal feeds, including Prof. Klopfenstein (University of Nebraska, Lincoln), Prof. Berger (University of Illinois, Urbana-Champaign), Mr.more » Madson (Rapheal Katzen International Associates, Inc.), and Prof. Trenkle (Iowa State University) (Wang 1999). Table 1 presents current dry milling coproduct displacement ratios being used in the GREET model. The current effort focuses on updating displacement ratios of dry milling corn-ethanol coproducts used in the animal feed industry. Because of the increased availability and use of these coproducts as animal feeds, more information is available on how these coproducts replace conventional animal feeds. To glean this information, it is also important to understand how industry selects feed. Because of the wide variety of available feeds, animal nutritionists use commercial software (such as Brill Formulation{trademark}) for feed formulation. The software recommends feed for the animal on the basis of the nutritional characteristics, availability, and price of various animal feeds, as well as on the nutritional requirements of the animal (Corn Refiners Association 2006). Therefore, feed formulation considers both the economic and the nutritional characteristics of feed products.« less

21 CFR 515.10 - Medicated feed mill license applications.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Federal Food, Drug, and Cosmetic Act (the act). (3) The name, title, and signature of the responsible...) of the act. (5) A certification that the methods used in, and the facilities and controls used for...

21 CFR 515.10 - Medicated feed mill license applications.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Federal Food, Drug, and Cosmetic Act (the act). (3) The name, title, and signature of the responsible...) of the act. (5) A certification that the methods used in, and the facilities and controls used for...

21 CFR 515.10 - Medicated feed mill license applications.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Federal Food, Drug, and Cosmetic Act (the act). (3) The name, title, and signature of the responsible...) of the act. (5) A certification that the methods used in, and the facilities and controls used for...

Effects on Vibration and Surface Roughness in High Speed Micro End-Milling of Inconel 718 with Minimum Quantity Lubrication

NASA Astrophysics Data System (ADS)

Rahman, Mohamed Abd; Yeakub Ali, Mohammad; Saddam Khairuddin, Amir

2017-03-01

This paper presents the study on vibration and surface roughness of Inconel 718 workpiece produced by micro end-milling using Mikrotools Integrated Multi-Process machine tool DT-110 with control parameters; spindle speed (15000 rpm and 30000 rpm), feed rate (2 mm/min and 4 mm/min) and depth of cut (0.10 mm and 0.15mm). The vibration was measured using DYTRAN accelerometer instrument and the average surface roughness Ra was measured using Wyko NT1100. The analysis of variance (ANOVA) by using Design Expert software revealed that feed rate and depth of cut are the most significant factors on vibration meanwhile for average surface roughness, Ra, spindle speed is the most significant factor.

Rice mill wastewater treatment in microbial fuel cells fabricated using proton exchange membrane and earthen pot at different pH.

PubMed

Behera, Manaswini; Jana, Partha S; More, Tanaji T; Ghangrekar, M M

2010-10-01

Performance of microbial fuel cells (MFCs), fabricated using an earthen pot (MFC-1) and a proton exchange membrane (MFC-2), was evaluated while treating rice mill wastewater at feed pH of 8.0, 7.0 and 6.0. A third MFC (MFC-3), fabricated using a proton exchange membrane (PEM), was operated as control without pH adjustment of the acidic raw wastewater. Maximum chemical oxygen demand (COD) removal efficiencies of 96.5% and 92.6% were obtained in MFC-1 and MFC-2, respectively, at feed pH of 8.0. MFC-3 showed maximum COD removal of 87%. The lignin removal was 84%, 79%, and 77% and the phenol removal was 81%, 77%, and 76% in MFC-1, MFC-2, and MFC-3, respectively. Maximum sustainable volumetric power was obtained at feed pH of 8.0, and it was 2.3 W/m(3) and 0.53 W/m(3), with 100 ohm external resistance, in MFC-1 and MFC-2, respectively. The power was lower at lower feed pH. MFC-3 generated lowest volumetric power (0.27 W/m(3)) as compared to MFC-1 and MFC-2. More effective treatment of rice mill wastewater and higher energy recovery was demonstrated by earthen pot MFC as compared to MFC incorporated with PEM. 2010 Elsevier B.V. All rights reserved.

Rapid fabrication of miniature lens arrays by four-axis single point diamond machining

PubMed Central

McCall, Brian; Tkaczyk, Tomasz S.

2013-01-01

A novel method for fabricating lens arrays and other non-rotationally symmetric free-form optics is presented. This is a diamond machining technique using 4 controlled axes of motion – X, Y, Z, and C. As in 3-axis diamond micro-milling, a diamond ball endmill is mounted to the work spindle of a 4-axis ultra-precision computer numerical control (CNC) machine. Unlike 3-axis micro-milling, the C-axis is used to hold the cutting edge of the tool in contact with the lens surface for the entire cut. This allows the feed rates to be doubled compared to the current state of the art of micro-milling while producing an optically smooth surface with very low surface form error and exceptionally low radius error. PMID:23481813

Feed supplemented with byproducts from olive oil mill wastewater processing increases antioxidant capacity in broiler chickens.

PubMed

Gerasopoulos, Konstantinos; Stagos, Dimitrios; Kokkas, Stylianos; Petrotos, Konstantinos; Kantas, Dimitrios; Goulas, Panagiotis; Kouretas, Dimitrios

2015-08-01

In the present study, a ceramic membrane microfiltration method was used for the separation of two liquid products, the downstream permeate and the upstream retentate, from olive mill wastewater (OMWW). These liquid products were examined for their antioxidant activity by incorporating them into broilers' feed. Twenty four broilers 13 d old were divided into two feeding groups receiving supplementation with OMWW retentate or permeate for 37 d. Blood was drawn at 17, 27 and 37 d, while tissues (muscle, heart, liver) were collected at 37 d. The antioxidant effects were assessed by measuring oxidative stress biomarkers in blood and tissues. The results showed that broilers given feed supplemented with OMWW retentate or permeate had significantly lower protein oxidation and lipid peroxidation levels and higher total antioxidant capacity in plasma and tissues compared to control group. In both OMWW groups, catalase activity in erythrocytes and tissues was significantly increased compared to control group. OMWW retentate administration increased significantly GSH in erythrocytes in broilers with low GSH, although both OMWW products significantly reduced GSH in broilers with high GSH. Thus, it has been demonstrated for the first time that supplementation with OMWW processing residues could be used for enhancing broilers' redox status. Copyright © 2015 Elsevier Ltd. All rights reserved.

13. INTERIOR VIEW, FIRST FLOOR SHOWING THE ELEVATORS FEEDING GRAIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. INTERIOR VIEW, FIRST FLOOR SHOWING THE ELEVATORS FEEDING GRAIN FROM THE SECOND FLOOR TO THE GRINDING STONES, WITH GRAIN ELEVATORS IN BACKGROUND (NOTE OUTLINE ON THE FLOOR WHERE ROLLER MILLS WERE ORIGINALLY PLACED) - Schech's Mill, Beaver Creek State Park, La Crescent, Houston County, MN

7 CFR 305.26 - Khapra beetle treatment schedule for feeds and milled products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE PHYTOSANITARY TREATMENTS Heat... requirements. This treatment must be specifically authorized in each case by the Director of Plant Health... 7 Agriculture 5 2010-01-01 2010-01-01 false Khapra beetle treatment schedule for feeds and milled...

Work Tasks as Determinants of Grain Dust and Microbial Exposure in the Norwegian Grain and Compound Feed Industry.

PubMed

Straumfors, Anne; Heldal, Kari Kulvik; Wouters, Inge M; Eduard, Wijnand

2015-07-01

The grain and compound feed industry entails inevitable risks of exposure to grain dust and its microbial content. The objective of this study was therefore to investigate task-dependent exposure differences in order to create knowledge basis for awareness and exposure reducing measures in the Norwegian grain and compound feed industry. A total of 166 samples of airborne dust were collected by full-shift personal sampling during work in 20 grain elevators and compound feed mills during one autumn season and two winter seasons. The personal exposure to grain dust, endotoxins, β-1→3-glucans, bacteria, and fungal spores was quantified and used as individual outcomes in mixed models with worker nested in company as random effect and different departments and tasks as fixed effects. The exposure levels were highest in grain elevator departments. Exposure to endotoxins was particularly high. Tasks that represented the highest and lowest exposures varied depending on the bioaerosol component. The most important determinants for elevated dust exposure were cleaning and process controlling. Cleaning increased the dust exposure level by a factor of 2.44 of the reference, from 0.65 to 1.58mg m(-3), whereas process controlling increased the dust exposure level by a factor of 2.97, from 0.65 to 1.93mg m(-3). Process controlling was associated with significantly less grain dust exposure in compound feed mills and the combined grain elevators and compound feed mills, than in grain elevators. The exposure was reduced by a factor of 0.18 and 0.22, from 1.93 to 0.34mg m(-3) and to 0.42mg m(-3), respectively, compared with the grain elevators. Inspection/maintenance, cleaning, and grain rotation and emptying were determinants of higher exposure to both endotoxin and β-1→3-glucans. Seed winnowing was in addition a strong determinant for endotoxin, whereas mixing of animal feed implied higher β-1→3-glucan exposure. Cleaning was the only task that contributed significantly to higher exposure to bacteria and fungal spores. Cleaning in all companies and process controlling in grain elevators were the strongest determinants for overall exposure, whereas seed winnowing was a particular strong determinant of endotoxin exposure. Exposure reduction by technical intervention or personal protective equipment should therefore be considered at work places with identified high exposure tasks. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Investigation into process-induced de-aggregation of cohesive micronised API particles.

PubMed

Hoffmann, Magnus; Wray, Patrick S; Gamble, John F; Tobyn, Mike

2015-09-30

The aim of this study was to assess the impact of unit processes on the de-aggregation of a cohesive micronised API within a pharmaceutical formulation using near-infrared chemical imaging. The impact on the primary API particles was also investigated using an image-based particle characterization system with integrated Raman analysis. The blended material was shown to contain large, API rich domains which were distributed in-homogeneously across the sample, suggesting that the blending process was not aggressive enough to disperse aggregates of micronised drug particles. Cone milling, routinely used to improve the homogeneity of such cohesive formulations, was observed to substantially reduce the number and size of API rich domains; however, several smaller API domains survived the milling process. Conveyance of the cone milled formulation through the Alexanderwerk WP120 powder feed system completely dispersed all remaining aggregates. Importantly, powder feed transmission of the un-milled formulation was observed to produce an equally homogeneous API distribution. The size of the micronised primary drug particles remained unchanged during powder feed transmission. These findings provide further evidence that this powder feed system does induce shear, and is in fact better able to disperse aggregates of a cohesive micronised API within a blend than the blend-mill-blend step. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

The FEM Simulation on End Mill of Plastic Doors and Windows Corner Cleaning Based on Deform-3D

NASA Astrophysics Data System (ADS)

Li, Guoping; Huang, Zhenyong; Wang, Xiaohui

2017-12-01

In the plastic doors and windows corner cleaning process, the rotating speed, the feed rate and the milling cutter diameter are the main factors that affect the efficiency and quality of the of corner cleaning. In this paper, SolidWorks will be used to establish the 3D model of end mills, and use Deform-3D to research the end mill milling process. And using orthogonal experiment design method to analyze the effect of rotating speed, the feed rate and the milling cutter diameter on the axial force variation, and to get the overall trend of axial force and the selection of various parameters according to the influence of axial force change. Finally, simulate milling experiment used to get the actual axial force data to verify the reliability of the FEM simulation model. And the conclusion obtained in this paper has important theoretical value in improving the plastic doors and windows corner cleaning efficiency and quality.

Modeling and Analysis of CNC Milling Process Parameters on Al3030 based Composite

NASA Astrophysics Data System (ADS)

Gupta, Anand; Soni, P. K.; Krishna, C. M.

2018-04-01

The machining of Al3030 based composites on Computer Numerical Control (CNC) high speed milling machine have assumed importance because of their wide application in aerospace industries, marine industries and automotive industries etc. Industries mainly focus on surface irregularities; material removal rate (MRR) and tool wear rate (TWR) which usually depends on input process parameters namely cutting speed, feed in mm/min, depth of cut and step over ratio. Many researchers have carried out researches in this area but very few have taken step over ratio or radial depth of cut also as one of the input variables. In this research work, the study of characteristics of Al3030 is carried out at high speed CNC milling machine over the speed range of 3000 to 5000 r.p.m. Step over ratio, depth of cut and feed rate are other input variables taken into consideration in this research work. A total nine experiments are conducted according to Taguchi L9 orthogonal array. The machining is carried out on high speed CNC milling machine using flat end mill of diameter 10mm. Flatness, MRR and TWR are taken as output parameters. Flatness has been measured using portable Coordinate Measuring Machine (CMM). Linear regression models have been developed using Minitab 18 software and result are validated by conducting selected additional set of experiments. Selection of input process parameters in order to get best machining outputs is the key contributions of this research work.

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi Method

NASA Astrophysics Data System (ADS)

Hazza Faizi Al-Hazza, Muataz; Ibrahim, Nur Asmawiyah bt; Adesta, Erry T. Y.; Khan, Ahsan Ali; Abdullah Sidek, Atiah Bt.

2017-03-01

One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed milling, hard milling and dry milling. However, one of the most important challenges in this process is to control the flank wear rate. Therefore a analyzing the flank wear rate during machining should be investigated in order to determine the best cutting levels that will not affect the final quality of the product. In this research Taguchi method has been used to investigate the effect of cutting speed, feed rate and depth of cut and determine the best level s to minimize the flank wear rate up to total length of 0.3mm based on the ISO standard to maintain the finishing requirements.

9 CFR 149.7 - Recordkeeping at site.

Code of Federal Regulations, 2010 CFR

2010-01-01

... disposal method for all unused bait that is replaced. (iv) It must document the brand name and active... the feed mill maintains records of pest management practices or has records generated by a pest... normal business hours. (Approved by the Office of Management and Budget under control number 0579-0323) ...

Experimental study of fiber-glass plastic work pieces contour milling

NASA Astrophysics Data System (ADS)

Trushin, N. N.; Lisitsin, V. N.

2018-03-01

The article represents the results of study of cut and feed speed influence on wear of monolithic hard alloy end milling cutter during cutting of foiled fiber-glass plastic sheets, used for printed-circuit boards’ production. The peculiarities and problems of cutting layered materials are described. The most effective feed and cut speed values are determined by cutter wear analysis.

21 CFR 515.22 - Suspension and/or revocation of approval of a medicated feed mill license.

Code of Federal Regulations, 2011 CFR

2011-04-01

... mill license approved under section 512(m)(2) of the Federal Food, Drug, and Cosmetic Act (the act) and... hazard to the health of man or of the animals for which such animal feed is intended. (b) The... approved under section 512(m)(2) of the act and afford an opportunity for a hearing on a proposal to revoke...

Detection of internally infested popcorn using electrically conductive roller mills

USDA-ARS?s Scientific Manuscript database

To detect popcorn kernels infested by the internal feeding stored-product insect pest Sitophilus zeamais, maize weevil, a laboratory roller mill was modified so that the electrical conductivity of the grain is measured while the kernels are milled between the rolls. When a kernel with a S. zeamais l...

21. RW Meyer Sugar Mill: 18761889. Simple, singlecylinder, horizontal, reciprocating ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. RW Meyer Sugar Mill: 1876-1889. Simple, single-cylinder, horizontal, reciprocating steam engine, model no. 1, 5' x 10', 6 hp, 175 rpm. Manufactured by Ames Iron Works, Oswego, New York, 1879. View: Steam engine powered the mill's centrifugals. Steam-feed pipe at top left of engine. Steam exhaust pipe leaves base of engine on right end and projects upwards. The boiler feed and supply pipe running water through the engine's pre-heat system are seen running to the lower left end of the engine. Pulley in the foreground was not used. The centrifugals were powered by a belt running from the flywheel in the background. Ball-type governor and pulley are on left end of the engine. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Shear Roll Mill Reactivation

DTIC Science & Technology

2012-09-13

pneumatically operated paste dumper and belt conveyor system, the loss in weight feeder system, the hydraulically operated shear roll mill, the pellet...out feed belt conveyor , and the pack out system comprised of the metal detector, scale, and pack out empty and full drum roller conveyors . Page | 4...feed hopper and conveyor supplying the loss in weight feeder were turned on, and it was verified that these items functioned as designed . The

Towards quality by design in pharmaceutical manufacturing: modelling and control of air jet mills

NASA Astrophysics Data System (ADS)

Bhonsale, Satyajeet; Telen, Dries; Stokbroekx, Bard; Van Impe, Jan

2017-06-01

Milling is an important step in pharmaceutical manufacturing as it not only determines the final formulation of the drug product, but also influences the bioavailability and dissolution rate of the active pharmaceutical ingredient (API). In this respect, the air jet mill (AJM) is most commonly used in the pharmaceutical industry as it is a non-contaminating and non-degrading self-classifying process capable of delivering narrow particle size distributions (PSD). Keeping the principles of Quality by Design in mind, the Critical Process Parameters (CPPs) of the AJM have been identified to be the pressures at the grinding nozzles, and the feed rate which affect the PSD, surface charge and the morphology of the product (i.e. the Critical Material Attributes (CMAs)). For the purpose of this research, the PSD is considered to be the only relevant CMA. A population balance based model is proposed to simulate the dynamics milling operation by utilizing the concept of breakage functions. This model agrees qualitatively with experimental observations of the air jet mill unit present at Janssen Pharmaceutica but further steps for model validation need to be carried out.

Co-firing of paper mill sludge and coal in an industrial circulating fluidized bed boiler.

PubMed

Tsai, Meng-Yuan; Wu, Keng-Tung; Huang, Chin-Cheng; Lee, Hom-Ti

2002-01-01

Co-firing of coal and paper mill sludge was conducted in a 103 MWth circulating fluidized bed boiler to investigate the effect of the sludge feeding rate on emissions of SOx, NOx, and CO. The preliminary results show that emissions of SOx and Nx decrease with increasing sludge feeding rate, but CO shows the reverse tendency due to the decrease in combustion temperature caused by a large amount of moisture in the sludge. All emissions met the local environmental requirements. The combustion ashes could be recycled as feed materials in the cement manufacturing process.

64. NORTH WALL OF CRUSHED OXIDIZED ORE BIN. THE PRIMARY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

64. NORTH WALL OF CRUSHED OXIDIZED ORE BIN. THE PRIMARY MILL FEEDS AT BOTTOM. MILL SOLUTION TANKS WERE TO THE LEFT (EAST) AND BARREN SOLUTION TANK TO THE RIGHT (WEST) OR THE CRUSHED ORE BIN. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Machinability Study on Milling Kenaf Fiber Reinforced Plastic Composite Materials using Design of Experiments

NASA Astrophysics Data System (ADS)

Azmi, H.; Haron, C. H. C.; Ghani, J. A.; Suhaily, M.; Yuzairi, A. R.

2018-04-01

The surface roughness (Ra) and delamination factor (Fd) of a milled kenaf reinforced plastic composite materials are depending on the milling parameters (spindle speed, feed rate and depth of cut). Therefore, a study was carried out to investigate the relationship between the milling parameters and their effects on a kenaf reinforced plastic composite materials. The composite panels were fabricated using vacuum assisted resin transfer moulding (VARTM) method. A full factorial design of experiments was use as an initial step to screen the significance of the parameters on the defects using Analysis of Variance (ANOVA). If the curvature of the collected data shows significant, Response Surface Methodology (RSM) is then applied for obtaining a quadratic modelling equation that has more reliable in expressing the optimization. Thus, the objective of this research is obtaining an optimum setting of milling parameters and modelling equations to minimize the surface roughness (Ra) and delamination factor (Fd) of milled kenaf reinforced plastic composite materials. The spindle speed and feed rate contributed the most in affecting the surface roughness and the delamination factor of the kenaf composite materials.

Application of dragonfly algorithm for optimal performance analysis of process parameters in turn-mill operations- A case study

NASA Astrophysics Data System (ADS)

Vikram, K. Arun; Ratnam, Ch; Lakshmi, VVK; Kumar, A. Sunny; Ramakanth, RT

2018-02-01

Meta-heuristic multi-response optimization methods are widely in use to solve multi-objective problems to obtain Pareto optimal solutions during optimization. This work focuses on optimal multi-response evaluation of process parameters in generating responses like surface roughness (Ra), surface hardness (H) and tool vibration displacement amplitude (Vib) while performing operations like tangential and orthogonal turn-mill processes on A-axis Computer Numerical Control vertical milling center. Process parameters like tool speed, feed rate and depth of cut are considered as process parameters machined over brass material under dry condition with high speed steel end milling cutters using Taguchi design of experiments (DOE). Meta-heuristic like Dragonfly algorithm is used to optimize the multi-objectives like ‘Ra’, ‘H’ and ‘Vib’ to identify the optimal multi-response process parameters combination. Later, the results thus obtained from multi-objective dragonfly algorithm (MODA) are compared with another multi-response optimization technique Viz. Grey relational analysis (GRA).

Effect of dietary inclusion of sorghum milling waste on growth response, nutrient utilisation, gut characteristics and cecal microflora of weaner rabbits.

PubMed

Oso, Oladele A; Sobayo, Richard; Jegede, Vincent; Fafiolu, Adeboye; Iyasere, Oluwaseun Serah; Dele, Peter; Bamgbose, Adeyemi; Cecilia, Adesida

2011-06-01

Growth response, nutrient digestibility and cecal microflora of 80 male, mixed breed weaner rabbits fed with varying dietary inclusions of sorghum milling waste (SMW) was investigated. Four experimental diets were formulated such that SMW was included at 0 (control), 100, 200 and 300 g/kg, respectively. Each dietary treatment was performed on 20 rabbits. Feed intake increased (P < 0.05) while final live weight and feed conversion ratio of rabbits decreased (P < 0.05) following increased dietary inclusion of SMW. Rabbits fed with 100 and 200 g/kg SMW had similar feed conversion ratios, weight gain, crude fiber, dry matter and crude protein digestibility values. Rabbits fed with 300 g/kg SMW recorded the lowest (P < 0.05) hot carcass weight, dressing percentage and rack weight. Similar dressing percentage and rack weight were recorded for rabbits fed with control diet, 100 and 200 g/kg SMW. The weight of cecal content increased (P < 0.05) with increased dietary inclusion levels of SMW. Rabbits fed with 300 g/kg SMW recorded the lowest (P < 0.05) coliform and lactobaccillus counts. Dietary inclusion of up to 200 g/kg SMW supported improved growth response and carcass yield without imposing any detrimental effect on cecal microflora. © 2011 The Authors; Animal Science Journal © 2011 Japanese Society of Animal Science.

40 CFR 406.70 - Applicability; description of the animal feed subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... animal feed subcategory. 406.70 Section 406.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Animal Feed Subcategory § 406.70 Applicability; description of the animal feed subcategory. The provisions of this subpart are...

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREWFEED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREW-FEED COAL HOPPER ON RIGHT SIDE. - Cedar City Automotive Repair Shop, Automotive Repair Shop, 820 North Main Street, Cedar City, Iron County, UT

37. MILL NO. 2, 2nd FLOOR, CLOSE SHOT OF 2 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. MILL NO. 2, 2nd FLOOR, CLOSE SHOT OF 2 CREEL MACHINES, WHICH FEED YARN INTO KNITTING MACHINES. - Prattville Manufacturing Company, Number One, 242 South Court Street, Prattville, Autauga County, AL

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREWFEED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREW-FEED COAL HOPPER ON RIGHT SIDE, WITH SCALE. - Cedar City Automotive Repair Shop, Automotive Repair Shop, 820 North Main Street, Cedar City, Iron County, UT

10. RW Meyer Sugar Mill: 18761889. Simple, singlecylinder, horizontal, reciprocating ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. RW Meyer Sugar Mill: 1876-1889. Simple, single-cylinder, horizontal, reciprocating steam engine, model No. 1, 5' x 10', 6 hp, 175 rpm. Manufactured by Ames Iron Works, Oswego, New York, 1879. View: Steam engine powered the mill's centrifugals. To the left of the horizontal (fluted) cylinder is the water pump which moved the boiler feed water through the engine's pre-heat system (the exhaust steam heated the boiler feedwater before it was pumped on to the boiler). The steam-feed port, manual throttle valve, and fly-ball governor and pulley and to the right of the cylinder. The drive shaft with flywheel to the left and pulley to the right are seen behind the piston rod, cross-head, wrist pen, connecting rod and the slide valve and eccentric. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Implementation of design of experiments approach for the micronization of a drug with a high brittle-ductile transition particle diameter.

PubMed

Yazdi, Ashkan K; Smyth, Hugh D C

2017-03-01

To optimize air-jet milling conditions of ibuprofen (IBU) using design of experiment (DoE) method, and to test the generalizability of the optimized conditions for the processing of another non-steroidal anti-inflammatory drug (NSAID). Bulk IBU was micronized using an Aljet mill according to a circumscribed central composite (CCC) design with grinding and pushing nozzle pressures (GrindP, PushP) varying from 20 to 110 psi. Output variables included yield and particle diameters at the 50th and 90th percentile (D 50 , D 90 ). Following data analysis, the optimized conditions were identified and tested to produce IBU particles with a minimum size and an acceptable yield. Finally, indomethacin (IND) was milled using the optimized conditions as well as the control. CCC design included eight successful runs for milling IBU from the ten total runs due to powder "blowback" from the feed hopper. DoE analysis allowed the optimization of the GrindP and PushP at 75 and 65 psi. In subsequent validation experiments using the optimized conditions, the experimental D 50 and D 90 values (1.9 and 3.6 μm) corresponded closely with the DoE modeling predicted values. Additionally, the optimized conditions were superior over the control conditions for the micronization of IND where smaller D 50 and D 90 values (1.2 and 2.7 μm vs. 1.8 and 4.4 μm) were produced. The optimization of a single-step air-jet milling of IBU using the DoE approach elucidated the optimal milling conditions, which were used to micronize IND using the optimized milling conditions.

Investigation of formation of cut off layers and productivity of screw milling process

NASA Astrophysics Data System (ADS)

Ambrosimov, S. K.; Morozova, A. V.

2018-03-01

The article presents studies of a new method for complex milling surfaces with a screw feed motion. Using the apparatus of algebra of logic, the process of formation of cut metal layers and processing capacity is presented.

Experimental study of surface integrity and fatigue life in the face milling of inconel 718

NASA Astrophysics Data System (ADS)

Wang, Xiangyu; Huang, Chuanzhen; Zou, Bin; Liu, Guoliang; Zhu, Hongtao; Wang, Jun

2018-06-01

The Inconel 718 alloy is widely used in the aerospace and power industries. The machining-induced surface integrity and fatigue life of this material are important factors for consideration due to high reliability and safety requirements. In this work, the milling of Inconel 718 was conducted at different cutting speeds and feed rates. Surface integrity and fatigue life were measured directly. The effects of cutting speed and feed rate on surface integrity and their further influences on fatigue life were analyzed. Within the chosen parameter range, the cutting speed barely affected the surface roughness, whereas the feed rate increased the surface roughness through the ideal residual height. The surface hardness increased as the cutting speed and feed rate increased. Tensile residual stress was observed on the machined surface, which showed improvement with the increasing feed rate. The cutting speed was not an influencing factor on fatigue life, but the feed rate affected fatigue life through the surface roughness. The high surface roughness resulting from the high feed rate could result in a high stress concentration factor and lead to a low fatigue life.

47. VIEW OF FEED LEVEL, CRUSHED OXIDIZED ORE BIN FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

47. VIEW OF FEED LEVEL, CRUSHED OXIDIZED ORE BIN FROM EAST. THE 18 INCH BELT CONVEYOR FEED IS AT CENTER, WITH DRIVE GEAR. THE 16 INCH FINES FEED IS IN THE BACKGROUND AND 18 INCH BELT CONVEYOR DISCHARGE IS SLIGHTLY RIGHT OF CENTER. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Arsanilic acid blindness in pigs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menges, R.W.; Kintner, L.D.; Selby, L.A.

1970-06-01

Blindness in pigs that were given an overdosage of arsanilic acid is reported. A 0.0375% level of arsanilic acid was fed to 640 pigs for 90 days beginning when the animals were 3 months old. Approximately one month after the start of feeding, partial or complete blindness was observed in 50 of the pigs. Clinical signs, pathologic findings and the chemical analysis of hair are discussed. The level of arsanilic acid used was that recommended for the control of swine dysentery, to be fed for only five or six days. The overdosage resulted from a misunderstanding between the farmer andmore » the feed mill.« less

Real time monitoring of powder blend bulk density for coupled feed-forward/feed-back control of a continuous direct compaction tablet manufacturing process.

PubMed

Singh, Ravendra; Román-Ospino, Andrés D; Romañach, Rodolfo J; Ierapetritou, Marianthi; Ramachandran, Rohit

2015-11-10

The pharmaceutical industry is strictly regulated, where precise and accurate control of the end product quality is necessary to ensure the effectiveness of the drug products. For such control, the process and raw materials variability ideally need to be fed-forward in real time into an automatic control system so that a proactive action can be taken before it can affect the end product quality. Variations in raw material properties (e.g., particle size), feeder hopper level, amount of lubrication, milling and blending action, applied shear in different processing stages can affect the blend density significantly and thereby tablet weight, hardness and dissolution. Therefore, real time monitoring of powder bulk density variability and its incorporation into the automatic control system so that its effect can be mitigated proactively and efficiently is highly desired. However, real time monitoring of powder bulk density is still a challenging task because of different level of complexities. In this work, powder bulk density which has a significant effect on the critical quality attributes (CQA's) has been monitored in real time in a pilot-plant facility, using a NIR sensor. The sensitivity of the powder bulk density on critical process parameters (CPP's) and CQA's has been analyzed and thereby feed-forward controller has been designed. The measured signal can be used for feed-forward control so that the corrective actions on the density variations can be taken before they can influence the product quality. The coupled feed-forward/feed-back control system demonstrates improved control performance and improvements in the final product quality in the presence of process and raw material variations. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of feed grinding methods with and without expansion on prececal and total tract mineral digestibility as well as on interior and exterior egg quality in laying hens.

PubMed

Hafeez, A; Mader, A; Ruhnke, I; Männer, K; Zentek, J

2016-01-01

The grinding of cereals by various milling methods as well as thermal treatment of feed may influence mineral digestibility and egg quality. The present study investigated the effect of feed produced by disc mill (D) and wedge-shaped disc mill (WSD), as mash (M) or expandate (E) on apparent ileal absorption (AIA) and apparent total digestibility (ATD) of calcium, phosphorus, magnesium, zinc, manganese, copper and iron, as well as on egg quality in laying hens. A total of 192 hens (Lohmann Brown) aged 19 wk, were assigned using a randomized design with a 2 × 2 factorial arrangement. Four experimental diets were offered ad libitum. Eggs were analyzed for weight, shape index, area, shell weight per unit surface area, yolk color, air cell, blood spot, Haugh unit, albumen and yolk measures (index, weight, height, width and length), shell measures (surface area, stability, density, thickness and membrane weight), as well as percent contents of albumen, yolk, shell, and shell membrane. The ATD for phosphorus, manganese, and copper was higher in WSD compared with D treatment (P = 0.028, P = 0.028 and P = 0.016, respectively). The interaction between milling methods and thermal treatment influenced ATD of copper (P = 0.033), which was higher in WSD+M group (41.0 ± 20.2) compared with D+E group (-3.21 ± 25.1), whereas no differences were observed for D+M (1.90 ± 37.8) and WSD+E (8.02 ± 36.2) groups. Egg stability tended to be higher in E compared with M treatment (P = 0.055). Albumen weight, percentage albumen weight, and albumen: yolk were higher and percentage yolk weight was lower in D compared with WSD treatment (P = 0.043, P = 0.027, P = 0.024, and P = 0.041, respectively). Number of blood spots was higher in E than M treatment (P = 0.053). In conclusion, use of a wedge-shaped disc mill resulted in higher ATD for phosphorus, manganese, and copper than use of a disc mill; however, digestibility for majority of minerals as well as egg quality parameters was comparable. Therefore, feed produced by either disc mill or wedge-shaped disc mill as mash or expandate may be used for laying hens without negative effects on egg quality. © 2015 Poultry Science Association Inc.

Comparative Investigation on Tool Wear during End Milling of AISI H13 Steel with Different Tool Path Strategies

NASA Astrophysics Data System (ADS)

Adesta, Erry Yulian T.; Riza, Muhammad; Avicena

2018-03-01

Tool wear prediction plays a significant role in machining industry for proper planning and control machining parameters and optimization of cutting conditions. This paper aims to investigate the effect of tool path strategies that are contour-in and zigzag tool path strategies applied on tool wear during pocket milling process. The experiments were carried out on CNC vertical machining centre by involving PVD coated carbide inserts. Cutting speed, feed rate and depth of cut were set to vary. In an experiment with three factors at three levels, Response Surface Method (RSM) design of experiment with a standard called Central Composite Design (CCD) was employed. Results obtained indicate that tool wear increases significantly at higher range of feed per tooth compared to cutting speed and depth of cut. This result of this experimental work is then proven statistically by developing empirical model. The prediction model for the response variable of tool wear for contour-in strategy developed in this research shows a good agreement with experimental work.

Incidence of Nontyphoidal Salmonella in Food-Producing Animals, Animal Feed, and the Associated Environment in South Africa, 2012-2014.

PubMed

Magwedere, Kudakwashe; Rauff, Dionne; De Klerk, Grietjie; Keddy, Karen H; Dziva, Francis

2015-11-01

Nontyphoidal salmonellosis continues to pose a global threat to human health, primarily by causing food-borne illnesses, and food-producing animals are the principal reservoirs of many pathogenic serovars. To identify key control points and generate information that may enable future estimation of the transmission routes between the environment, animals, and humans, we examined data on Salmonella isolates in South Africa. Samples were obtained from livestock and poultry on farms, meat at abattoirs, raw materials at feed mills, animal feed, and environmental sources (eg, poultry houses, abattoirs, feed mills, water) from 2012 to 2014 in compliance with each establishment's protocols conforming to International Organization for Standardization (ISO) (ISO/TS 17728, ISO 18593:2004 and ISO 17604:2003) standards. Isolation and serotyping of Salmonella were performed according to the scope of accreditation of the respective laboratories conforming to ISO/IEC 17025:2005 standard techniques. Salmonella was isolated from 9031 of 180 298 (5.0%) samples, and these isolates were distributed among 188 different serovars. Salmonella Enteritidis was the most frequent isolate, with 1944 of 180 298 (21.5%) originating from poultry on farms, poultry meat, and poultry houses, followed by Salmonella Havana, with 677 of 180 298 (7.5%), mostly from environmental samples. Serovars that are uncommonly associated with human disease (Salmonella Idikan, Salmonella Salford, and Salmonella Brancaster) were isolated at higher frequencies than Salmonella Typhimurium, a common cause of human illness. Environmental samples accounted for 3869 of 9031 (42.8%) samples positive for Salmonella. We describe the frequent isolation of Salmonella of a wide variety of serovars, from an array of animal feeds, food animals, and food animal environment. As prevention of human salmonellosis requires the effective control of Salmonella in food animals, these data can be used to facilitate Salmonella control in food animals and thereby prevent human infections. © The Author 2015. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Sources of Salmonella on broiler carcasses during transportation and processing: modes of contamination and methods of control.

PubMed

Corry, Janet E L; Allen, V M; Hudson, W R; Breslin, M F; Davies, R H

2002-01-01

The prevalence and types of salmonella in broiler chickens during transportation and during slaughter and dressing were studied. This was part of a comprehensive investigation of salmonellas in two UK poultry companies, which aimed to find the origins and mechanisms of salmonella contamination. Salmonellas were isolated using cultural methods. Serovars of Salmonella detected during rearing were usually also found in a small proportion of birds on the day of slaughter and on the carcasses at various points during processing. There was little evidence of salmonellas spreading to large numbers of carcasses during processing. Many serovars found in the feedmills or hatcheries were also detected in the birds during rearing and/or slaughter. Transport crates were contaminated with salmonellas after washing and disinfection. Prevalence of salmonellas fell in the two companies during this survey. A small number of serovars predominated in the processing plants of each company. These serovars originated from the feed mills. Reasons for transport crate contamination were: (1) inadequate cleaning, resulting in residual faecal soiling; (2) disinfectant concentration and temperature of disinfectant too low; (3) contaminated recycled flume water used to soak the crates. Efforts to control salmonella infection in broilers need to concentrate on crate cleaning and disinfection and hygiene in the feed mills.

Surface topography and roughness of high-speed milled AlMn1Cu

NASA Astrophysics Data System (ADS)

Wang, Zhenhua; Yuan, Juntang; Yin, Zengbin; Hu, Xiaoqiu

2016-10-01

The aluminum alloy AlMn1Cu has been broadly applied for functional parts production because of its good properties. But few researches about the machining mechanism and the surface roughness were reported. The high-speed milling experiments are carried out in order to improve the machining quality and reveal the machining mechanism. The typical topography features of machined surface are observed by scan electron microscope(SEM). The results show that the milled surface topography is mainly characterized by the plastic shearing deformation surface and material piling zone. The material flows plastically along the end cutting edge of the flat-end milling tool and meanwhile is extruded by the end cutting edge, resulting in that materials partly adhere to the machined surface and form the material piling zone. As the depth of cut and the feed per tooth increase, the plastic flow of materials is strengthened and the machined surface becomes rougher. However, as the cutting speed increases, the plastic flow of materials is weakened and the milled surface becomes smoother. The cutting parameters (e.g. cutting speed, feed per tooth and depth of cut) influencing the surface roughness are analyzed. It can be concluded that the roughness of the machined surface formed by the end cutting edge is less than that by the cylindrical cutting edge when a cylindrical flat-end mill tool is used for milling. The proposed research provides the typical topography features of machined surface of the anti-rust aluminum alloy AlMn1Cu in high speed milling.

A new optimization tool path planning for 3-axis end milling of free-form surfaces based on efficient machining intervals

NASA Astrophysics Data System (ADS)

Vu, Duy-Duc; Monies, Frédéric; Rubio, Walter

2018-05-01

A large number of studies, based on 3-axis end milling of free-form surfaces, seek to optimize tool path planning. Approaches try to optimize the machining time by reducing the total tool path length while respecting the criterion of the maximum scallop height. Theoretically, the tool path trajectories that remove the most material follow the directions in which the machined width is the largest. The free-form surface is often considered as a single machining area. Therefore, the optimization on the entire surface is limited. Indeed, it is difficult to define tool trajectories with optimal feed directions which generate largest machined widths. Another limiting point of previous approaches for effectively reduce machining time is the inadequate choice of the tool. Researchers use generally a spherical tool on the entire surface. However, the gains proposed by these different methods developed with these tools lead to relatively small time savings. Therefore, this study proposes a new method, using toroidal milling tools, for generating toolpaths in different regions on the machining surface. The surface is divided into several regions based on machining intervals. These intervals ensure that the effective radius of the tool, at each cutter-contact points on the surface, is always greater than the radius of the tool in an optimized feed direction. A parallel plane strategy is then used on the sub-surfaces with an optimal specific feed direction for each sub-surface. This method allows one to mill the entire surface with efficiency greater than with the use of a spherical tool. The proposed method is calculated and modeled using Maple software to find optimal regions and feed directions in each region. This new method is tested on a free-form surface. A comparison is made with a spherical cutter to show the significant gains obtained with a toroidal milling cutter. Comparisons with CAM software and experimental validations are also done. The results show the efficiency of the method.

The Tool Life of Ball Nose end Mill Depending on the Different Types of Ramping

NASA Astrophysics Data System (ADS)

Vopát, Tomáš; Peterka, Jozef; Kováč, Martin

2014-12-01

The article deals with the cutting tool wear measurement process and tool life of ball nose end mill depending on upward ramping and downward ramping. The aim was to determine and compare the wear (tool life) of ball nose end mill for different types of copy milling operations, as well as to specify particular steps of the measurement process. In addition, we examined and observed cutter contact areas of ball nose end mill with machined material. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, cutting speed, feed rate, axial depth of cut and radial depth of cut were not changed. The cutting tool wear was measured on Zoller Genius 3s universal measuring machine. The results show different tool life of ball nose end mills depending on the copy milling strategy.

Assessing the specific energy consumption and physical properties of comminuted Douglas-fir chips for bioconversion

Treesearch

Yalan Liu; Jinwu Wang; Michael P. Wolcott

2016-01-01

Size reduction homogenizes the bulk biomass and facilitates downstream feedstock handling, transportation, and storage. Effects of feeding rate, mill-type (hammer and knife mill), screen size, and moisture content on comminution energy consumption of commercial Douglas-fir (Pseudotsuga menziesii) pulp chips were quantified. The resulting particles...

Furniture rough mill costs evaluated by computer simulation

Treesearch

R. Bruce Anderson

1983-01-01

A crosscut-first furniture rough mill was simulated to evaluate processing and raw material costs on an individual part basis. Distributions representing the real-world characteristics of lumber, equipment feed speeds, and processing requirements are programed into the simulation. Costs of parts from a specific cutting bill are given, and effects of lumber input costs...

High-conversion hydrolysates and corn sweetener production in dry-grind corn process.

USDA-ARS?s Scientific Manuscript database

Most corn is processed to fuel ethanol and distillers’ grain animal feed using the dry grind process. However, wet milling is needed to refine corn starch. Corn starch is in turn processed to numerous products, including glucose and syrup. However, wet milling is a capital, labor, and energy intensi...

76 FR 60941 - Policy Regarding Submittal of Amendments for Processing of Equivalent Feed at Licensed Uranium...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-30

... State-licensed uranium recovery site, either conventional, heap leach, or in situ recovery. DATES... types of new uranium recovery facilities (conventional mills, heap leach facilities, and in situ... from the ground for processing at a mill. Rather, the ore is processed in-situ with the resulting...

No gastric mill in sauropod dinosaurs: new evidence from analysis of gastrolith mass and function in ostriches

PubMed Central

Wings, Oliver; Sander, P. Martin

2006-01-01

Polished pebbles occasionally found within skeletons of giant herbivorous sauropod dinosaurs are very likely to be gastroliths (stomach stones). Here, we show that based on feeding experiments with ostriches and comparative data for relative gastrolith mass in birds, sauropod gastroliths do not represent the remains of an avian-style gastric mill. Feeding experiments with farm ostriches showed that bird gastroliths experience fast abrasion in the gizzard and do not develop a polish. Relative gastrolith mass in sauropods (gastrolith mass much less than 0.1% of body mass) is at least an order of magnitude less than that in ostriches and other herbivorous birds (gastrolith mass approximates 1% of body mass), also arguing against the presence of a gastric mill in sauropods. Sauropod dinosaurs possibly compensated for their limited oral processing and gastric trituration capabilities by greatly increasing food retention time in the digestive system. Gastrolith clusters of some derived theropod dinosaurs (oviraptorosaurs and ornithomimosaurs) compare well with those of birds, suggesting that the gastric mill evolved in the avian stem lineage. PMID:17254987

Optimize Operating Conditions on Fine Particle Grinding Process with Vertically Stirred Media Mill

NASA Astrophysics Data System (ADS)

Yang, Yang; Rowson, Neil; Ingram, Andy

2016-11-01

Stirred media mill recently is commonly utilized among mining process due to its high stressing intensity and efficiency. However, the relationship between size reduction and flow pattern within the mixing pot is still not fully understand. Thus, this work investigates fine particle grinding process within vertically stirred media mills by altering stirrer geometry, tip speed and solids loading. Positron Emitting Particle Tracking (PEPT) technology is utilized to plot routine of particles velocity map. By tacking trajectory of a single particle movement within the mixing vessel, the overall flow pattern is possible to be plotted. Ground calcium carbonate, a main product of Imerys, is chosen as feeding material (feed size D80 30um) mixed with water to form high viscous suspension. To obtain fine size product (normally D80 approximately 2um), large amount of energy is drawn by grinding mill to break particles through impact, shear attrition or compression or a combination of them. The results indicate higher energy efficient is obtained with more dilute suspension. The optimized stirrer proves more energy-saving performance by altering the slurry circulate. Imerys Minerals Limited.

Feasibility investigations on multi-cutter milling process: A novel fabrication method for microreactors with multiple microchannels

NASA Astrophysics Data System (ADS)

Pan, Minqiang; Zeng, Dehuai; Tang, Yong

A novel multi-cutter milling process for multiple parallel microchannels with manifolds is proposed to address the challenge of mass manufacture as required for cost-effective commercial applications. Several slotting cutters are stacked together to form a composite tool for machining microchannels simultaneously. The feasibility of this new fabrication process is experimentally investigated under different machining conditions and reaction characteristics of methanol steam reforming for hydrogen production. The influences of cutting parameters and the composite tool on the microchannel qualities and burr formation are analyzed. Experimental results indicate that larger cutting speed, smaller feed rate and cutting depth are in favor of obtaining relatively good microchannel qualities and small burrs. Of all the cutting parameters considered in these experiments, 94.2 m min -1 cutting speed, 23.5 mm min -1 feed rate and 0.5 mm cutting depth are found to be the optimum value. According to the comparisons of experimental results of multi-cutter milling process and estimated one of other alternative methods, it is found that multi-cutter milling process shows much shorter machining time and higher work removal rate than that of other alternative methods. Reaction characteristics of methanol steam reforming in microchannels also indicate that multi-cutter milling process is probably suitable for a commercial application.

Improvement of single wavelength-based Thai jasmine rice identification with elliptic Fourier descriptor and neural network analysis

NASA Astrophysics Data System (ADS)

Suwansukho, Kajpanya; Sumriddetchkajorn, Sarun; Buranasiri, Prathan

2012-11-01

Instead of considering only the amount of fluorescent signal spatially distributed on the image of milled rice grains this paper shows how our single-wavelength spectral-imaging-based Thai jasmine (KDML105) rice identification system can be improved by analyzing the shape and size of the image of each milled rice variety especially during the image threshold operation. The image of each milled rice variety is expressed as chain codes and elliptic Fourier coefficients. After that, a feed-forward back-propagation neural network model is applied, resulting in an improved average FAR of 11.0% and FRR of 19.0% in identifying KDML105 milled rice from the unwanted four milled rice varieties.

Control of fumonisin: effects of processing.

PubMed Central

Saunders, D S; Meredith, F I; Voss, K A

2001-01-01

Of about 10 billion bushels of corn that are grown each year in the United States, less than 2% is processed directly into food products, and about 18% is processed into intermediates such as high-fructose corn syrup, ethanol, and cornstarch. The vast majority of the annual crop is used domestically for animal feed (60%), and about 16% is exported. Thus, any program for controlling residues of fumonisin (FB) in food must recognize that most of the crop is grown for something other than food. Studies on the effects of wet milling on FB residues found these residues nondetectable in cornstarch, the starting material for high-fructose corn syrup and most other wet-milled food ingredients. Similar effects are noted for the dry-milling process. FB residues were nondetectable or quite low in dry flaking grits and corn flour, higher in corn germ, and highest in corn bran. Extrusion of dry-milled products reduces FB concentrations by 30-90% for mixing-type extruders and 20-50% for nonmixing extruders. Cooking and canning generally have little effect on FB content. In the masa process measurable FB is reduced following the cooking, soaking, and washing steps, with little conversion of FB to the hydrolyzed form. Sheeting, baking, and frying at commercial times and temperatures generally have no effect. In summary, all available studies on the effects of processing corn into food and food ingredients consistently demonstrate substantial reductions in measurable FB. No studies have shown a concentration in FB residues in food products or ingredients. PMID:11359704

7. RW Meyer Sugar Mill: 18761889. Engine and boiler house; ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. RW Meyer Sugar Mill: 1876-1889. Engine and boiler house; ca. 1881. Simple, single-cylinder, horizontal, reciprocating steam engine, model No. 1, 5' x 10', 6 hp, 175 rpm. Manufactured by Ames Iron Works, Oswego, New York, 1879. View: Historical view, 1934, from T. T. Waterman collection, Hawaiian Sugar Planters' Association. View shows interior of engine and boiler house intact. The steam-feed pipe is still attached to throttle valve, not the case in 1978 view. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Design and evaluation of a low-volume total suspended particulate sampler

USDA-ARS?s Scientific Manuscript database

The regulation of particulate matter (PM) emitted by agricultural sources, e.g., cotton gins, feed mills, and concentrated animal feeding operations (CAFOs), is based on downwind concentrations of particulate matter less than 10 and 2.5 'm (PM10 and PM2.5) aerodynamic equivalent diameter (AED). Both...

Use of Computer Simulation in Designing and Evaluating a Proposed Rough Mill for Furniture Interior Parts

Treesearch

Philip A. Araman

1977-01-01

The design of a rough mill for the production of interior furniture parts is used to illustrate a simulation technique for analyzing and evaluating established and proposed sequential production systems. Distributions representing the real-world random characteristics of lumber, equipment feed speeds and delay times are programmed into the simulation. An example is...

Neural networks with fuzzy Petri nets for modeling a machining process

NASA Astrophysics Data System (ADS)

Hanna, Moheb M.

1998-03-01

The paper presents an intelligent architecture based a feedforward neural network with fuzzy Petri nets for modeling product quality in a CNC machining center. It discusses how the proposed architecture can be used for modeling, monitoring and control a product quality specification such as surface roughness. The surface roughness represents the output quality specification manufactured by a CNC machining center as a result of a milling process. The neural network approach employed the selected input parameters which defined by the machine operator via the CNC code. The fuzzy Petri nets approach utilized the exact input milling parameters, such as spindle speed, feed rate, tool diameter and coolant (off/on), which can be obtained via the machine or sensors system. An aim of the proposed architecture is to model the demanded quality of surface roughness as high, medium or low.

Laser milling of martensitic stainless steels using spiral trajectories

NASA Astrophysics Data System (ADS)

Romoli, L.; Tantussi, F.; Fuso, F.

2017-04-01

A laser beam with sub-picosecond pulse duration was driven in spiral trajectories to perform micro-milling of martensitic stainless steel. The geometry of the machined micro-grooves channels was investigated by a specifically conceived Scanning Probe Microscopy instrument and linked to laser parameters by using an experimental approach combining the beam energy distribution profile and the absorption phenomena in the material. Preliminary analysis shows that, despite the numerous parameters involved in the process, layer removal obtained by spiral trajectories, varying the radial overlap, allows for a controllable depth of cut combined to a flattening effect of surface roughness. Combining the developed machining strategy to a feed motion of the work stage, could represent a method to obtain three-dimensional structures with a resolution of few microns, with an areal roughness Sa below 100 nm.

Optimization of Milling Parameters Employing Desirability Functions

NASA Astrophysics Data System (ADS)

Ribeiro, J. L. S.; Rubio, J. C. Campos; Abrão, A. M.

2011-01-01

The principal aim of this paper is to investigate the influence of tool material (one cermet and two coated carbide grades), cutting speed and feed rate on the machinability of hardened AISI H13 hot work steel, in order to identify the cutting conditions which lead to optimal performance. A multiple response optimization procedure based on tool life, surface roughness, milling forces and the machining time (required to produce a sample cavity) was employed. The results indicated that the TiCN-TiN coated carbide and cermet presented similar results concerning the global optimum values for cutting speed and feed rate per tooth, outperforming the TiN-TiCN-Al2O3 coated carbide tool.

Results of a 90-day safety assurance study with rats fed grain from corn borer-protected corn.

PubMed

Hammond, B G; Dudek, R; Lemen, J K; Nemeth, M A

2006-07-01

The results of a 90-day rat feeding study with grain from MON 810 corn (YieldGard Cornborer -- YieldGard Cornborer is a registered trademark of Monsanto Technology, LLC) that is protected against feeding damage from corn and stalk boring lepidopteran insects are presented. Corn borer protection was accomplished through the introduction of cry1Ab coding sequences into the corn genome for in planta production of a bioactive form of Cry1Ab protein. Grain from MON 810 and its near-isogenic control was separately formulated into rodent diets at levels of 11% and 33% (w/w) by Purina Mills, Inc. (PMI). All diets were nutritionally balanced and conformed to PMI specifications for Certified LabDiet (PMI Certified LabDiet 5002 is a registered trademark of Purina Mills, Inc.) 5002. There were a total of 400 rats in the study divided into 10 groups of 20 rats/sex/group. The responses of rats fed diets containing MON 810 were compared to those of rats fed grain from conventional corn varieties. Overall health, body weight, food consumption, clinical pathology parameters (hematology, blood chemistry, urinalysis), organ weights, and gross and microscopic appearance of tissues were comparable between groups fed diets containing MON 810 and conventional corn varieties. This study complements extensive agronomic, compositional and farm animal feeding studies with MON 810 grain, confirming that it is as safe and nutritious as grain from existing commercial corn varieties.

Functional morphology of comminuting feeding structures of Trichodactylus borellianus (Brachyura, Decapoda, Trichodactylidae), an omnivorous freshwater crab.

PubMed

Carvalho, Débora de Azevedo; Viozzi, Maria Florencia; Collins, Pablo Agustín; Williner, Verónica

2017-07-01

Crustaceans exhibit great diversity of feeding structures with morphological traits that are useful to infer the general trophic habits of species. In this study, we analyzed the functional morphology of comminuting feeding structures (mandibles, chelipeds, gastric mill) of the freshwater crab Trichodactylus borellianus directly related with the food fragmentation. The heterochely and mechanical advantage (MA) of the chelae were also studied. In both analyses, we considered the relationship between morphology and the natural diet. We expected to find a consistent relation between feeding habits and morphological traits. In general, we found simple structures armed with uniform setal systems and feeding appendages without pronounced teeth or spines. Mandibles have primarily cutting functions, helping with the food anchoring and fragmentation with mandibular palps armed with pappose setae. Chelipeds were covered with spines and simple setae. Adult males exhibited right-handedness with high MA of the major chelae. The ingested, relatively large pieces of food are finally chewed by a gastric mill equipped with sharp cusps characteristic of decapods with low ingestion of crude fiber material. The morphology of the feeding apparatus revealed that it is well adapted to an omnivorous diet, being able to cope with dietary changes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimization of multi response in end milling process of ASSAB XW-42 tool steel with liquid nitrogen cooling using Taguchi-grey relational analysis

NASA Astrophysics Data System (ADS)

Norcahyo, Rachmadi; Soepangkat, Bobby O. P.

2017-06-01

A research was conducted for the optimization of the end milling process of ASSAB XW-42 tool steel with multiple performance characteristics based on the orthogonal array with Taguchi-grey relational analysis method. Liquid nitrogen was applied as a coolant. The experimental studies were conducted under varying the liquid nitrogen cooling flow rates (FL), and the end milling process variables, i.e., cutting speed (Vc), feeding speed (Vf), and axial depth of cut (Aa). The optimized multiple performance characteristics were surface roughness (SR), flank wear (VB), and material removal rate (MRR). An orthogonal array, signal-to-noise (S/N) ratio, grey relational analysis, grey relational grade, and analysis of variance were employed to study the multiple performance characteristics. Experimental results showed that flow rate gave the highest contribution for reducing the total variation of the multiple responses, followed by cutting speed, feeding speed, and axial depth of cut. The minimum surface roughness, flank wear, and maximum material removal rate could be obtained by using the values of flow rate, cutting speed, feeding speed, and axial depth of cut of 0.5 l/minute, 109.9 m/minute, 440 mm/minute, and 0.9 mm, respectively.

Modeling the milling tool wear by using an evolutionary SVM-based model from milling runs experimental data

NASA Astrophysics Data System (ADS)

Nieto, Paulino José García; García-Gonzalo, Esperanza; Vilán, José Antonio Vilán; Robleda, Abraham Segade

2015-12-01

The main aim of this research work is to build a new practical hybrid regression model to predict the milling tool wear in a regular cut as well as entry cut and exit cut of a milling tool. The model was based on Particle Swarm Optimization (PSO) in combination with support vector machines (SVMs). This optimization mechanism involved kernel parameter setting in the SVM training procedure, which significantly influences the regression accuracy. Bearing this in mind, a PSO-SVM-based model, which is based on the statistical learning theory, was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. To accomplish the objective of this study, the experimental dataset represents experiments from runs on a milling machine under various operating conditions. In this way, data sampled by three different types of sensors (acoustic emission sensor, vibration sensor and current sensor) were acquired at several positions. A second aim is to determine the factors with the greatest bearing on the milling tool flank wear with a view to proposing milling machine's improvements. Firstly, this hybrid PSO-SVM-based regression model captures the main perception of statistical learning theory in order to obtain a good prediction of the dependence among the flank wear (output variable) and input variables (time, depth of cut, feed, etc.). Indeed, regression with optimal hyperparameters was performed and a determination coefficient of 0.95 was obtained. The agreement of this model with experimental data confirmed its good performance. Secondly, the main advantages of this PSO-SVM-based model are its capacity to produce a simple, easy-to-interpret model, its ability to estimate the contributions of the input variables, and its computational efficiency. Finally, the main conclusions of this study are exposed.

40 CFR 63.1349 - Performance testing requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-line kiln/raw mill is not operating. The owner or operator of a clinker cooler subject to limitations..., kg/dscm. Qsd = volumetric flow rate of effluent gas, dscm/hr. P = total kiln feed (dry basis), Mg/hr... kiln feed (dry basis), Mg/hr. (v) Except as provided in paragraph (b)(1)(vi) of this section the...

Artificial Intelligence vs. Statistical Modeling and Optimization of Continuous Bead Milling Process for Bacterial Cell Lysis.

PubMed

Haque, Shafiul; Khan, Saif; Wahid, Mohd; Dar, Sajad A; Soni, Nipunjot; Mandal, Raju K; Singh, Vineeta; Tiwari, Dileep; Lohani, Mohtashim; Areeshi, Mohammed Y; Govender, Thavendran; Kruger, Hendrik G; Jawed, Arshad

2016-01-01

For a commercially viable recombinant intracellular protein production process, efficient cell lysis and protein release is a major bottleneck. The recovery of recombinant protein, cholesterol oxidase (COD) was studied in a continuous bead milling process. A full factorial response surface methodology (RSM) design was employed and compared to artificial neural networks coupled with genetic algorithm (ANN-GA). Significant process variables, cell slurry feed rate (A), bead load (B), cell load (C), and run time (D), were investigated and optimized for maximizing COD recovery. RSM predicted an optimum of feed rate of 310.73 mL/h, bead loading of 79.9% (v/v), cell loading OD 600 nm of 74, and run time of 29.9 min with a recovery of ~3.2 g/L. ANN-GA predicted a maximum COD recovery of ~3.5 g/L at an optimum feed rate (mL/h): 258.08, bead loading (%, v/v): 80%, cell loading (OD 600 nm ): 73.99, and run time of 32 min. An overall 3.7-fold increase in productivity is obtained when compared to a batch process. Optimization and comparison of statistical vs. artificial intelligence techniques in continuous bead milling process has been attempted for the very first time in our study. We were able to successfully represent the complex non-linear multivariable dependence of enzyme recovery on bead milling parameters. The quadratic second order response functions are not flexible enough to represent such complex non-linear dependence. ANN being a summation function of multiple layers are capable to represent complex non-linear dependence of variables in this case; enzyme recovery as a function of bead milling parameters. Since GA can even optimize discontinuous functions present study cites a perfect example of using machine learning (ANN) in combination with evolutionary optimization (GA) for representing undefined biological functions which is the case for common industrial processes involving biological moieties.

Artificial Intelligence vs. Statistical Modeling and Optimization of Continuous Bead Milling Process for Bacterial Cell Lysis

PubMed Central

Haque, Shafiul; Khan, Saif; Wahid, Mohd; Dar, Sajad A.; Soni, Nipunjot; Mandal, Raju K.; Singh, Vineeta; Tiwari, Dileep; Lohani, Mohtashim; Areeshi, Mohammed Y.; Govender, Thavendran; Kruger, Hendrik G.; Jawed, Arshad

2016-01-01

For a commercially viable recombinant intracellular protein production process, efficient cell lysis and protein release is a major bottleneck. The recovery of recombinant protein, cholesterol oxidase (COD) was studied in a continuous bead milling process. A full factorial response surface methodology (RSM) design was employed and compared to artificial neural networks coupled with genetic algorithm (ANN-GA). Significant process variables, cell slurry feed rate (A), bead load (B), cell load (C), and run time (D), were investigated and optimized for maximizing COD recovery. RSM predicted an optimum of feed rate of 310.73 mL/h, bead loading of 79.9% (v/v), cell loading OD600 nm of 74, and run time of 29.9 min with a recovery of ~3.2 g/L. ANN-GA predicted a maximum COD recovery of ~3.5 g/L at an optimum feed rate (mL/h): 258.08, bead loading (%, v/v): 80%, cell loading (OD600 nm): 73.99, and run time of 32 min. An overall 3.7-fold increase in productivity is obtained when compared to a batch process. Optimization and comparison of statistical vs. artificial intelligence techniques in continuous bead milling process has been attempted for the very first time in our study. We were able to successfully represent the complex non-linear multivariable dependence of enzyme recovery on bead milling parameters. The quadratic second order response functions are not flexible enough to represent such complex non-linear dependence. ANN being a summation function of multiple layers are capable to represent complex non-linear dependence of variables in this case; enzyme recovery as a function of bead milling parameters. Since GA can even optimize discontinuous functions present study cites a perfect example of using machine learning (ANN) in combination with evolutionary optimization (GA) for representing undefined biological functions which is the case for common industrial processes involving biological moieties. PMID:27920762

A Performance Comparison Study of Uncoated and TiAlN Coated Carbide End Mill on Machining of the Al-35Zn Alloy

NASA Astrophysics Data System (ADS)

Bayraktar, S.; Hekimoglu, A. P.; Turgut, Y.; Haciosmanoglu, M.

2018-01-01

In this study, Al-35Zn alloy was produced by permanent mold casting. To investigate the cutting performance of uncoated and TiAlN coated carbide end mills on this alloy, a series of tests were carried out in the CNC vertical machining center at a constant cutting speed, feed rate and depth of cut. The results obtained from the tests showed that uncoated carbide end mill have lower cutting force and surface roughness than TiAlN coated carbide end mill. These observations are discussed in terms of the alloys properties, cutting tool surfaces, and friction and wear behavior between the cutting tool and the material.

Nutritional strategies to combat Salmonella in mono-gastric food animal production.

PubMed

Berge, A C; Wierup, M

2012-04-01

Nutritional strategies to minimize Salmonella in food animal production are one of the key components in producing safer food. The current European approach is to use a farm-to-fork strategy, where each sector must implement measures to minimize and reduce Salmonella contamination. In the pre-harvest phase, this means that all available tools need to be used such as implementation of biosecurity measures, control of Salmonella infections in animals at the farm as well as in transport and trade, optimal housing and management including cleaning, disinfection procedures as well as efforts to achieve Salmonella-free feed production. This paper describes some nutritional strategies that could be used in farm control programmes in the major mono-gastric food production animals: poultry and pigs. Initially, it is important to prevent the introduction of Salmonella onto the farm through Salmonella-contaminated feed and this risk is reduced through heat treatment and the use of organic acids and their salts and formaldehyde. Microbiological sampling and monitoring for Salmonella in the feed mills is required to minimize the introduction of Salmonella via feed onto the farm. In addition, feed withdrawal may create a stressful situation in animals, resulting in an increase in Salmonella shedding. Physical feed characteristics such as coarse-ground meal to pigs can delay gastric emptying, thereby increasing the acidity of the gut and thus reducing the possible prevalence of Salmonella. Coarse-ground grains and access to litter have also been shown to decrease Salmonella shedding in poultry. The feed can also modify the gastro-intestinal tract microflora and influence the immune system, which can minimize Salmonella colonization and shedding. Feed additives, such as organic acids, short- and medium-chain fatty acids, probiotics, including competitive exclusion cultures, prebiotics and certain specific carbohydrates, such as mannan-based compounds, egg proteins, essential oils and bacteriophages, have the potential to reduce Salmonella levels when added to the feed. These nutritional strategies could be evaluated and used in farm control programmes.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

PubMed Central

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed. PMID:28787882

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data.

PubMed

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-28

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC-MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc . Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC-MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Study on the surface constitute properties of high-speed end milling aluminum alloy

NASA Astrophysics Data System (ADS)

Huang, Xiaoming; Li, Hongwei; Yumeng, Ma

2017-09-01

The physical and mechanical properties of the metal surface will change after the metal cutting processing. The comprehensive study of the influence of machining parameters on surface constitute properties are necessary. A high-speed milling experiment by means of orthogonal method with four factors was conducted for aluminum alloy7050-T7451. The surface constitutive properties of the Al-Alloy surface were measured using SSM-B4000TM stress-strain microprobe system. Based on all the load-depth curves obtained, the characteristics parameters such as strain hardening exponent n and yield strength σy of the milling surface are calculated. The effect of cutting speed, feed rate, and width and depth of cut on n and σy was investigated using the ANOVA techniques. The affecting degree of milling parameters on n and σy was v>fz> ap < ae. The influence of milling parameters on n and σ y was described and discussed.

Chromium concentrations in ruminant feed ingredients.

PubMed

Spears, J W; Lloyd, K E; Krafka, K

2017-05-01

Chromium (Cr), in the form of Cr propionate, has been permitted for supplementation to cattle diets in the United States at levels up to 0.50 mg of Cr/kg of DM since 2009. Little is known regarding Cr concentrations naturally present in practical feed ingredients. The present study was conducted to determine Cr concentrations in feed ingredients commonly fed to ruminants. Feed ingredients were collected from dairy farms, feed mills, grain bins, and university research farms. Mean Cr concentrations in whole cereal grains ranged from 0.025 mg/kg of DM for oats to 0.041 mg/kg of DM for wheat. Grinding whole samples of corn, soybeans, and wheat through a stainless steel Wiley mill screen greatly increased analyzed Cr concentrations. Harvested forages had greater Cr concentrations than concentrates, and alfalfa hay or haylage had greater Cr concentrations than grass hay or corn silage. Chromium in alfalfa hay or haylage (n = 13) averaged 0.522 mg/kg of DM, with a range of 0.199 to 0.889 mg/kg of DM. Corn silage (n = 21) averaged 0.220 mg of Cr/kg of DM with a range of 0.105 to 0.441 mg of Cr/kg of DM. By-product feeds ranged from 0.040 mg of Cr/kg of DM for cottonseed hulls to 1.222 mg of Cr/kg of DM for beet pulp. Of the feed ingredients analyzed, feed grade phosphate sources had the greatest Cr concentration (135.0 mg/kg). Most ruminant feedstuffs and feed ingredients had less than 0.50 mg of Cr/kg of DM. Much of the analyzed total Cr in feed ingredients appears to be due to Cr contamination from soil or metal contact during harvesting, processing, or both. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Millworkers' Asthma: Allergic Responses to the Grain Weevil (Sitophilus granarius)

PubMed Central

Lunn, J. A.

1966-01-01

Two laboratory workers, who spent a considerable time each day handling grain infested by the grain weevil (Sitophilus granarius), developed allergic responses to this insect varying from rhinitis and pruritus to marked asthma. These findings suggested that weevil protein present in mill dust could result in sensitization in those exposed continuously. A pilot study was therefore undertaken on 75 volunteer millworkers to determine whether such sensitivity existed. A millworker was defined as anyone who worked in a flour mill or mill producing animal feed from mixed cereals, or who worked in grain-storing silos. Skin testing with weevil, mixed flour extracts, and a control was carried out on all 75 volunteers; 57% had a positive response to the weevil extract and 68% a positive response to the mixed flour extract. In a control group of 100 workers from two engineering firms matched for age and sex, 34% were positive to the weevil extract and 17% to mixed flour. From the initial 75 millworkers, 15 were selected for further study based on a positive skin response to the weevil and a history of a productive cough and chest tightness and wheezing when exposed to mill dust. The forced expiratory volume in one second (F.E.V.1·0) was measured after control inhalations and after weevil and mixed flour inhalations. Significant reductions of 20% and 15·4% were found in two subjects after inhalation of weevil extract. In one case wheezing and cough developed. The changes in F.E.V.1·0 were reversed after inhalation of a bronchodilator aerosol. Twenty-five of the control subjects with positive skin responses to the grain weevil were given similar provocation inhalations but none showed any significant change in F.E.V.1·0. This pilot study suggests that grain weevil sensitivity is an additional factor in millworkers' asthma. PMID:5929689

Behavioral response of manatees to variations in environmental sound levels

USGS Publications Warehouse

Miksis-Olds, Jennifer L.; Wagner, Tyler

2011-01-01

Florida manatees (Trichechus manatus latirostris) inhabit coastal regions because they feed on the aquatic vegetation that grows in shallow waters, which are the same areas where human activities are greatest. Noise produced from anthropogenic and natural sources has the potential to affect these animals by eliciting responses ranging from mild behavioral changes to extreme aversion. Sound levels were calculated from recordings made throughout behavioral observation periods. An information theoretic approach was used to investigate the relationship between behavior patterns and sound level. Results indicated that elevated sound levels affect manatee activity and are a function of behavioral state. The proportion of time manatees spent feeding and milling changed in response to sound level. When ambient sound levels were highest, more time was spent in the directed, goal-oriented behavior of feeding, whereas less time was spent engaged in undirected behavior such as milling. This work illustrates how shifts in activity of individual manatees may be useful parameters for identifying impacts of noise on manatees and might inform population level effects.

Design and milling manufacture of polyurethane custom contoured cushions for wheelchair users.

PubMed

da Silva, Fabio Pinto; Beretta, Elisa Marangon; Prestes, Rafael Cavalli; Kindlein Junior, Wilson

2011-01-01

The design of custom contoured cushions manufactured in flexible polyurethane foams is an option to improve positioning and comfort for people with disabilities that spend most of the day seated in the same position. These surfaces increase the contact area between the seat and the user. This fact contributes to minimise the local pressures that can generate problems like decubitus ulcers. The present research aims at establishing development routes for custom cushion production to wheelchair users. This study also contributes to the investigation of Computer Numerical Control (CNC) machining of flexible polyurethane foams. The proposed route to obtain the customised seat began with acquiring the user's contour in adequate posture through plaster cast. To collect the surface geometry, the cast was three-dimensionally scanned and manipulated in CAD/CAM software. CNC milling parameters such as tools, spindle speeds and feed rates to machine flexible polyurethane foams were tested. These parameters were analysed regarding the surface quality. The best parameters were then tested in a customised seat. The possible dimensional changes generated during foam cutting were analysed through 3D scanning. Also, the customised seat pressure and temperature distribution was tested. The best parameters found for foams with a density of 50kg/cm(3) were high spindle speeds (24000 rpm) and feed rates between 2400-4000mm/min. Those parameters did not generate significant deformities in the machined cushions. The custom contoured cushion satisfactorily increased the contact area between wheelchair and user, as it distributed pressure and heat evenly. Through this study it was possible to define routes for the development and manufacturing of customised seats using direct CNC milling in flexible polyurethane foams. It also showed that custom contoured cushions efficiently distribute pressure and temperature, which is believed to minimise tissue lesions such as pressure ulcers.

Production of lactic acid from the mixture of softwood pre-hydrolysate and paper mill sludge by simultaneous saccharification and fermentation.

PubMed

Shi, Suan; Kang, Li; Lee, Y Y

2015-03-01

Paper mill sludge is a solid waste material composed of pulp residues and ash generated from pulping and paper making process. The carbohydrate portion of the sludges from Kraft/Recycle paper mill has chemical and physical characteristics similar to those of commercial wood pulp. Because of its high carbohydrate content and well-dispersed structure, the sludge can be biologically converted to value-added products without pretreatment. In bioconversion of solid feedstock such as paper mill sludge, a certain amount of water must be present to attain fluidity. In this study, hemicellulose pre-hydrolysate, in place of water, was added to the sludge to increase the concentration of the final product. Pre-hydrolysate was obtained by hot-water treatment of pine wood in which the total sugar concentration reached 4 wt.%. The mixture was processed by simultaneous saccharification and fermentation (SSF) using enzymes (cellulase and pectinase) and Lactobacillus rhamnosus (ATCC-10863). Pectinase was added to hydrolyze mannose oligomers in the pre-hydrolysate to monomers. During the SSF of the mixture, calcium carbonate in the paper sludge acted as a buffer, yielding calcium lactate as the final product. External pH control was unnecessary due to the buffer action of calcium carbonate that maintained the pH near optimum for the SSF. The lactic acid yield in the range of 80-90 % of the theoretical maximum was obtained. Use of the mixed feed of pre-hydrolysate and pulp mill sludges in the SSF raised the product concentration to 60 g of lactate/L.

17 CFR 32.1 - Scope of part 32; definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., corn, oats, barley, rye, flaxseed, grain sorghums, mill feeds, butter, eggs, onions, Solanum tuberosum..., livestock, livestock products and frozen concentrated orange juice; (2) Interstate commerce shall be...

90. PORTLAND FILTER FLOOR FROM SOUTHEAST. CYANIDE FEED TOWER TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

90. PORTLAND FILTER FLOOR FROM SOUTHEAST. CYANIDE FEED TOWER TO SUMP, LOWER RIGHT QUADRANT. DIAGONAL PIPE IN UPPER RIGHT IS AIR LINE TO AGITATORS. LAUNDER PARALLEL TO LEFT EDGE (FILLED WITH DEBRIS) RUNS FROM PRIMARY THICKENER No. 2 TO GOLD TANK No. 2. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

169. PORTLAND FILTER FLOOR FROM SOUTHEAST. CYANIDE FEED TOWER TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

169. PORTLAND FILTER FLOOR FROM SOUTHEAST. CYANIDE FEED TOWER TO SUMP, LOWER RIGHT QUADRANT. DIAGONAL PIPE IN UPPER RIGHT IS AIR LINE TO AGITATORS. LAUNDER PARALLEL TO LEFT EDGE (FILLED WITH DEBRIS) RUNS FROM PRIMARY THICKENER No. 2 TO GOLD TANK No. 2 - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

44. VIEW OF SOUTHWEST CORNER OF DRYER ROOM. DRYER FOUNDATION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. VIEW OF SOUTHWEST CORNER OF DRYER ROOM. DRYER FOUNDATION AT BOTTOM OF VIEW, WITH 18 INCH REVERSIBLE BELT CONVEYOR (UPPER LEFT), AND 16 INCH BELT CONVEYOR FINES FEED TO CRUSHED OXIDIZED ORE BIN (CENTER TO UPPER RIGHT). DRYER EXHAUST IS BELOW FINES FEED BELT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Triaxial Measurement Method for Analysis of Residual Stress after High Feed Milling by X-Ray Diffraction

NASA Astrophysics Data System (ADS)

Čuma, Matúš; Török, Jozef; Telišková, Monika

2016-12-01

Surface integrity is a broad term which includes various quality factors affecting the functional properties of parts. Residual stress is one of these factors. Machining generates residual stresses in the surface and subsurface layers of the structural elements. X-ray diffractometry is a non-destructive method applicable for the measurement of residual stresses in surface and subsurface layers of components. The article is focused on the non-destructive progressive method of triaxial measurement of residual stress after machining the surface of sample by high feed milling technology. Significance of triaxial measuring is the capability of measuring in different angles so it is possible to acquire stress tensor containing normal and shear stress components acting in the spot of measuring, using a Cartesian coordinate system.

Development of Rapid Detection and Genetic Characterization of Salmonella in Poultry Breeder Feeds

PubMed Central

Jarquin, Robin; Hanning, Irene; Ahn, Soohyoun; Ricke, Steven C.

2009-01-01

Salmonella is a leading cause of foodborne illness in the United States, with poultry and poultry products being a primary source of infection to humans. Poultry may carry some Salmonella serovars without any signs or symptoms of disease and without causing any adverse effects to the health of the bird. Salmonella may be introduced to a flock by multiple environmental sources, but poultry feed is suspected to be a leading source. Detecting Salmonella in feed can be challenging because low levels of the bacteria may not be recovered using traditional culturing techniques. Numerous detection methodologies have been examined over the years for quantifying Salmonella in feeds and many have proven to be effective for Salmonella isolation and detection in a variety of feeds. However, given the potential need for increased detection sensitivity, molecular detection technologies may the best candidate for developing rapid sensitive methods for identifying small numbers of Salmonella in the background of large volumes of feed. Several studies have been done using polymerase chain reaction (PCR) assays and commercial kits to detect Salmonella spp. in a wide variety of feed sources. In addition, DNA array technology has recently been utilized to track the dissemination of a specific Salmonella serotype in feed mills. This review will discuss the processing of feeds and potential points in the process that may introduce Salmonella contamination to the feed. Detection methods currently used and the need for advances in these methods also will be discussed. Finally, implementation of rapid detection for optimizing control methods to prevent and remove any Salmonella contamination of feeds will be considered. PMID:22346699

REF Onida Approval

EPA Pesticide Factsheets

This update August 9, 2016 letter from EPA approves, with modifications, the petition from Ring-neck Energy & Feed, LLC, REF Onida facility, with modifications, regarding non-grandfathered ethanol produced through a dry mill process

Determination of Specific Forces and Tool Deflections in Micro-milling of Ti-6Al-4V alloy using Finite Element Simulations and Analysis

NASA Astrophysics Data System (ADS)

Farina, Simone; Thepsonti, Thanongsak; Ceretti, Elisabetta; Özel, Tugrul

2011-05-01

Titanium alloys offer superb properties in strength, corrosion resistance and biocompatibility and are commonly utilized in medical devices and implants. Micro-end milling process is a direct and rapid fabrication method for manufacturing medical devices and implants in titanium alloys. Process performance and quality depend upon an understanding of the relationship between cutting parameters and forces and resultant tool deflections to avoid tool breakage. For this purpose, FE simulations of chip formation during micro-end milling of Ti-6Al-4V alloy with an ultra-fine grain solid carbide two-flute micro-end mill are investigated using DEFORM software. At first, specific forces in tangential and radial directions of cutting during micro-end milling for varying feed advance and rotational speeds have been determined using designed FE simulations for chip formation process. Later, these forces are applied to the micro-end mill geometry along the axial depth of cut in 3D analysis of ABAQUS. Consequently, 3D distributions for tool deflections & von Misses stress are determined. These analyses will yield in establishing integrated multi-physics process models for high performance micro-end milling and a leap-forward to process improvements.

9. RW Meyer Sugar Mill: 18761889. Locomotivetype, firetube, portable boiler, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. RW Meyer Sugar Mill: 1876-1889. Locomotive-type, fire-tube, portable boiler, No. 1 model. Manufactured by Ames Iron Works, Oswego, New York, 1879. 120 lbs/sq. inch working pressure, 66 sq. ft. heating surface in tubes. View: from side. The boiler provided steam for steam engine which in turn powered the mill's centrifugals. The section on the left side included the firebox with its surrounding water-legs. The fluted chimney-type structure is the steam port, safety valve, and whistle. Column projecting from side was part of steam pressure and water gauge. Pipe running above boiler carried steam to the engine. Pipe running below boiler provided the boiler feed-water. Cylindrical section included 22 fire-tube surrounded by water. The far right ... - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

8. RW Meyer Sugar Mill: 18761889. Simple, singlecylinder, horizontal, reciprocating ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. RW Meyer Sugar Mill: 1876-1889. Simple, single-cylinder, horizontal, reciprocating steam engine, model No. 1, 5' x 10', 6 hp, 175 rpm. Manufactured by Ames Iron Works, Oswego, New York, 1879. View: Steam engine powered the mill's centrifugals. It received steam from the locomotive type, fire-tube portable boiler in the background. The engine's water pump which pumped water from the feed-water clarifying cistern, in between the boiler and engine, through a pre-heat system and on to the boiler, is seen in front of the fluted cylinder. The fly-ball governor, missing its balls, the steam port, and manual throttle valve are above and behind the cylinder. The flywheel, drive shaft, and pulley are on the left side of the engine bed. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

The analysis of soil characteristics near the animal feed and fertiliser mill using the Bartington

NASA Astrophysics Data System (ADS)

Azhari, Adinda Syifa; Agustine, Eleonora; Fitriani, Dini

2017-07-01

Industrial activities have the potential to make pollution in agricultural land, the waste contains poisonous material and it is dangerous for the environment. In general, waste from factory is dumped directly into the river, but in the current study an object that is going to be conscientious is soil on around mill. There are three sampling sites are around fertilizer plants, feed mills and original uncontaminated soil. This research has been conducted to assess the impact of pollution resulting from the two mills for the environment. Physical parameter that used is magnetic susceptibility. Sampling was conducted using the method of magnetic susceptibility of rock to see the value of low frequency (lf) and shows Frequency Dependent (fd%) using the MS2B Bartington. The results from this study is at a location close to the fertilizer plant at a depth of 0-5 cm has a value susceptibility low frequency ( lf)=187.1 - 494.8, fd (%)=1.37 - 2:46, at a depth of 6-10 cm susceptibility value of low frequency (lf)=211 - 832.7,fd (%)=1.04 - 5.37. Results in the area of animal feed mill at a depth of 0-5 cm value susceptibility low frequency (lf)=111.9 - 325.7, fd (%)=0.8 - 3.57, at a depth of 6-10 cm value susceptibility low frequency (lf)=189.2 to 386.8,fd (%)=0.33 - 3.7. Results in the original soil at a depth of 0-5 cm susceptibility value of low frequency (lf)=1188.7 - 2237.8,fd (%)=2.75 - 4.65, at a depth of 6-10 cm value susceptibility low frequency (lf)=977.7 - 2134.7,fd (%)=3.06 - 6.21. The highest value was in the arealf original, shows the area has a high mineral content andlf lows were in the area near the factory fodder it is caused by high pollution, resulting in lower mineral content in the soil.

Kinetic study of ferronickel slag grinding at variation of ball filling and ratio of feed to grinding balls

NASA Astrophysics Data System (ADS)

Sanwani, Edy; Ikhwanto, Muhammad

2017-01-01

The objective of this paper is to investigate the effect of ball filling and ratio of feed to grinding balls on the kinetic of grinding of ferronickel slag in a laboratory scale ball mill. The experiments were started by crushing the ferronickel slag samples using a roll crusher to produce -3 mesh (-6.7 mm) product. This product, after sampling and sample dividing processes, was then used as feed for grinding process. The grinding was performed with variations of ball filling and ratio of feed to grinding balls for 150 minutes. At every certain time interval, particle size analysis was carried out on the grinding product. The results of the experiments were also used to develop linear regression model of the effect of grinding variables on the P80 of the product. Based on this study, it was shown that P80 values of the grinding products declined sharply until 70 minutes of grinding time due to the dominant mechanism of impact breakage and then decreased slowly after 70 minutes until 150 minutes of grinding time due to dominant mechanism of attrition breakage. Kinetics study of the grinding process on variations of grinding ball filling showed that the optimum rate of formation of fine particles for 20%, 30%, 40% and 50% mill volume was achieved at a particle size of 400 µm in which the best initial rate of formation occurred at 50% volume of mill. At the variations of ratio of feed to grinding balls it was shown that the optimum rate of grinding for the ratio of 1:10, 1: 8 and 1: 6 was achieved at a particle size of 400 µm and for the ratio of 1: 4 was at 841 µm in which the best initial rate of formation occurred at a 1:10 ratio. In this study, it was also produced two regression models that can predict the P80 value of the grinding product as a function of the variables of grinding time, ball filling and the ratio of the feed to grinding balls.

Influence of jet milling and particle size on the composition, physicochemical and mechanical properties of barley and rye flours.

PubMed

Drakos, Antonios; Kyriakakis, Georgios; Evageliou, Vasiliki; Protonotariou, Styliani; Mandala, Ioanna; Ritzoulis, Christos

2017-01-15

Finer barley and rye flours were produced by jet milling at two feed rates. The effect of reduced particle size on composition and several physicochemical and mechanical properties of all flours were evaluated. Moisture content decreased as the size of the granules decreased. Differences on ash and protein contents were observed. Jet milling increased the amount of damaged starch in both rye and barley flours. True density increased with decreased particle size whereas porosity and bulk density increased. The solvent retention capacity profile was also affected by jet milling. Barley was richer in phenolics and had greater antioxidant activity than rye. Regarding colour, both rye and barley flours when subjected to jet milling became brighter, whereas their yellowness was not altered significantly. The minimum gelation concentration for all flours was 16%w/v. Barley flour gels were stronger, firmer and more elastic than the rye ones. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fluid mechanics of slurry flow through the grinding media in ball mills

DOE Office of Scientific and Technical Information (OSTI.GOV)

Songfack, P.K.; Rajamani, R.K.

1995-12-31

The slurry transport within the ball mill greatly influences the mill holdup, residence time, breakage rate, and hence the power draw and the particle size distribution of the mill product. However, residence-time distribution and holdup in industrial mills could not be predicted a priori. Indeed, it is impossible to determine the slurry loading in continuously operating mills by direct measurement, especially in industrial mills. In this paper, the slurry transport problem is solved using the principles of fluid mechanics. First, the motion of the ball charge and its expansion are predicted by a technique called discrete element method. Then themore » slurry flow through the porous ball charge is tackled with a fluid-flow technique called the marker and cell method. This may be the only numerical technique capable of tracking the slurry free surface as it fluctuates with the motion of the ball charge. The result is a prediction of the slurry profile in both the radial and axial directions. Hence, it leads to the detailed description of slurry mass and ball charge within the mill. The model predictions are verified with pilot-scale experimental work. This novel approach based on the physics of fluid flow is devoid of any empiricism. It is shown that the holdup of industrial mills at a given feed percent solids can be predicted successfully.« less

Doxycycline and sulfadimethoxine transfer from cross-contaminated feed to chicken tissues.

PubMed

Segato, G; Benetti, C; Angeletti, R; Montesissa, C; Biancotto, G

2011-01-01

During feed preparation at feed mills or during feed mixing in bins at farms, the accidental contamination of feed at trace levels by veterinary drug residues, commonly known as carry-over, can accidentally but frequently occur. To evaluate the concentrations of residual antimicrobials in poultry edible tissues, due to contaminated feed, sulfadimethoxine and doxycycline were administered for 10 days to chickens in poultry feed incurred at the contamination levels frequently found during national feed monitoring programmes (1-5 mg kg(-1)). Sulfadimethoxine and doxycycline residual concentrations detected in muscle (

Experimental investigations on cryogenic cooling by liquid nitrogen in the end milling of hardened steel

NASA Astrophysics Data System (ADS)

Ravi, S.; Pradeep Kumar, M.

2011-09-01

Milling of hardened steel generates excessive heat during the chip formation process, which increases the temperature of cutting tool and accelerates tool wear. Application of conventional cutting fluid in milling process may not effectively control the heat generation also it has inherent health and environmental problems. To minimize health hazard and environmental problems caused by using conventional cutting fluid, a cryogenic cooling set up is developed to cool tool-chip interface using liquid nitrogen (LN 2). This paper presents results on the effect of LN 2 as a coolant on machinability of hardened AISI H13 tool steel for varying cutting speed in the range of 75-125 m/min during end milling with PVD TiAlN coated carbide inserts at a constant feed rate. The results show that machining with LN 2 lowers cutting temperature, tool flank wear, surface roughness and cutting forces as compared with dry and wet machining. With LN 2 cooling, it has been found that the cutting temperature was reduced by 57-60% and 37-42%; the tool flank wear was reduced by 29-34% and 10-12%; the surface roughness was decreased by 33-40% and 25-29% compared to dry and wet machining. The cutting forces also decreased moderately compared to dry and wet machining. This can be attributed to the fact that LN 2 machining provides better cooling and lubrication through substantial reduction in the cutting zone temperature.

Effects of feeding distillers dried grains with solubles to broilers from 0 to 28 days posthatch on broiler performance, feed manufacturing efficiency, and selected intestinal characteristics.

PubMed

Loar, R E; Moritz, J S; Donaldson, J R; Corzo, A

2010-10-01

This study evaluated the effect of 2 levels (0 vs. 8%) of distillers dried grains with solubles (DDGS) in a starter broiler diet (0 to 14 d; 45 replicates/treatment) after these same birds were subsequently fed a grower diet (14 to 28 d) with either 0, 7.5, 15, 22.5, or 30% DDGS (9 replicates/treatment). Ross×Ross 308 male broilers were used in this experiment, and evaluation criteria consisted of feed mill parameters, broiler growth, relative liver weight, ileal viscosity, and cecal content count of Clostridium perfringens and Escherichia coli analyzed by both selective media and real-time PCR. Increased inclusion of DDGS resulted in a nonlinear response for production rate (P<0.05), conditioner energy usage (P<0.01), and pellet mill energy usage (P<0.05). Increasing DDGS resulted in a linear decrease in pellet quality (P<0.001) and an increase (P<0.001) in total fines. Inclusion of DDGS decreased (P<0.001) energy usage at the pellet mill and decreased (P<0.05) bulk density of the diets. The DDGS levels fed during the starter phase (0 vs. 8%) had no effect on the broilers at 14 or at 28 d of age. Increasing DDGS inclusion levels during the grower phase resulted in a linear decrease (P<0.001) in BW gain and liver relative weight (P<0.001). A DDGS starter×grower interaction (P<0.05) was observed for feed consumption, in which birds that consumed no DDGS during the starter phase exhibited a decrease in feed consumption with the higher inclusion levels of DDGS during the grower phase, whereas birds that received 8% DDGS during the starter phase were unaffected by DDGS inclusion level in the grower phase. Feed conversion, mortality, ileal viscosity, and cecal C. perfringens and E. coli concentrations were unaffected by DDGS level in the grower diet. The feed intake response suggests a beneficial effect of exposing broiler chicks to DDGS if inclusion levels of 22.5% or higher are to be fed after 14 d of age. However, the data suggest that the young broiler can be negatively affected with inclusion levels of 15% DDGS or higher up to 28 d of age.

Confessions of a robot lobotomist

NASA Technical Reports Server (NTRS)

Gottshall, R. Marc

1994-01-01

Since its inception, numerically controlled (NC) machining methods have been used throughout the aerospace industry to mill, drill, and turn complex shapes by sequentially stepping through motion programs. However, the recent demand for more precision, faster feeds, exotic sensors, and branching execution have existing computer numerical control (CNC) and distributed numerical control (DNC) systems running at maximum controller capacity. Typical disadvantages of current CNC's include fixed memory capacities, limited communication ports, and the use of multiple control languages. The need to tailor CNC's to meet specific applications, whether it be expanded memory, additional communications, or integrated vision, often requires replacing the original controller supplied with the commercial machine tool with a more powerful and capable system. This paper briefly describes the process and equipment requirements for new controllers and their evolutionary implementation in an aerospace environment. The process of controller retrofit with currently available machines is examined, along with several case studies and their computational and architectural implications.

Influence of nanomechanical crystal properties on the comminution process of particulate solids in spiral jet mills.

PubMed

Zügner, Sascha; Marquardt, Karin; Zimmermann, Ingfried

2006-02-01

Elastic-plastic properties of single crystals are supposed to influence the size reduction process of bulk materials during jet milling. According to Pahl [M.H. Pahl, Zerkleinerungstechnik 2. Auflage. Fachbuchverlag, Leipzig (1993)] and H. Rumpf: [Prinzipien der Prallzerkleinerung und ihre Anwendung bei der Strahlmahlung. Chem. Ing. Tech., 3(1960) 129-135.] fracture toughness, maximum strain or work of fracture for example are strongly dependent on mechanical parameters like hardness (H) and young's modulus of elasticity (E). In addition the dwell time of particles in a spiral jet mill proved to correlate with the hardness of the feed material [F. Rief: Ph. D. Thesis, University of Würzburg (2001)]. Therefore 'near-surface' properties have a direct influence on the effectiveness of the comminution process. The mean particle diameter as well as the size distribution of the ground product may vary significantly with the nanomechanical response of the material. Thus accurate measurement of crystals' hardness and modulus is essential to determine the ideal operational micronisation conditions of the spiral jet mill. The recently developed nanoindentation technique is applied to examine subsurface properties of pharmaceutical bulk materials, namely calcite, sodium ascorbate, lactose and sodium chloride. Pressing a small sized tip into the material while continuously recording load and displacement, characteristic diagrams are derived. The mathematical evaluation of the force-displacement-data allows for calculation of the hardness and the elastic modulus of the investigated material at penetration depths between 50-300 nm. Grinding experiments performed with a modified spiral jet mill (Type Fryma JMRS 80) indicate the strong impact of the elastic-plastic properties of a given substance on its breaking behaviour. The fineness of milled products produced at constant grinding conditions but with different crystalline powders varies significantly as it is dependent on the nanohardness and the elasticity of the feed material. The analysis of this correlation gives new insights into the size reduction process.

Ball milling pretreatment of corn stover for enhancing the efficiency of enzymatic hydrolysis.

PubMed

Lin, Zengxiang; Huang, He; Zhang, Hongman; Zhang, Lin; Yan, Lishi; Chen, Jingwen

2010-11-01

Ethanol can be produced from lignocellulosic biomass with the usage of ball milling pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields from lignocellulosic feed stocks are critical parameters for ethanol production process. The research results from this paper indicated that the yields of glucose and xylose were improved by adding any of the following dilute chemical reagents: H(2)SO(4), HCl, HNO(3), CH(3)COOH, HCOOH, H(3)PO(4), and NaOH, KOH, Ca(OH)(2), NH(3)·H(2)O in the ball milling pretreatment of corn stover. The optimal enzymatic hydrolysis efficiencies were obtained under the conditions of ball milling in the alkali medium that was due to delignification. The data also demonstrated that ball milling pretreatment was a robust process. From the microscope image of ball milling-pretreated corn stover, it could be observed that the particle size of material was decreased and the fiber structure was more loosely organized. Meanwhile, the results indicate that the treatment effect of wet milling is better than that of dry milling. The optimum parameters for the milling process were ball speed of 350 r/min, solid/liquid ratio of 1:10, raw material particle size with 0.5 mm, and number of balls of 20 (steel ball, Φ = 10 mm), grinding for 30 min. In comparison with water milling process, alkaline milling treatment could increase the enzymatic hydrolysis efficiency of corn stover by 110%; and through the digestion process with the combination of xylanase and cellulase mixture, the hydrolysis efficiency could increase by 160%.

Formability behavior studies on CP-Al sheets processed through the helical tool path of incremental forming process

NASA Astrophysics Data System (ADS)

Markanday, H.; Nagarajan, D.

2018-02-01

Incremental sheet forming (ISF) is a novel die-less sheet metal forming process, which can produce components directly from the CAD geometry using a CNC milling machine at less production time and cost. The formability of the sheet material used is greatly affected by the process parameters involved and tool path adopted, and the present study is aimed to investigate the influence of different process parameter values using the helical tool path strategy on the formability of a commercial pure Al and to achieve maximum formability in the material. ISF experiments for producing an 80 mm diameter axisymmetric dome were carried out on 2 mm thickness commercially pure Al sheets for different tool speeds and feed rates in a CNC milling machine with a 10 mm hemispherical forming tool. The obtained parts were analyzed for springback, amount of thinning and maximum forming depth. The results showed that when the tool speed was increased by keeping the feed rate constant, the forming depth and thinning were also increased. On contrary, when the feed rate was increased by keeping the tool speed constant, the forming depth and thinning were decreased. Springback was found to be higher when the feed rate was increased rather than the tool speed was increased.

Development of the Direct Fabrication Process for Plutonium Immobilization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.W.

2001-07-10

The current baseline process for fabricating pucks for the Plutonium Immobilization Program includes granulation of the milled feed prior to compaction. A direct fabrication process was demonstrated that eliminates the need for granulation.

Surface morphology study in high speed milling of soda lime glass

NASA Astrophysics Data System (ADS)

Konneh, Mohamed; Bagum, Mst. Nasima; Ali, Mohammad Yeakub; Amin, A. K. M. Nurul

2018-05-01

Soda lime glass has a wide range of applications in optical, bio-medical and semi-conductor industries. It is undeniably a challenging task to produce micro finish surface on an amorphous brittle solid like soda lime glass due to its low fracture toughness. In order to obtain such a finish surface, ductile machining has been exploited, as this usually cause's plastic flow which control crack propagation. At sub-micro scale cutting parameters, researchers achieved nano finish surface in micro milling operation using coated tool. However it is possible to enhance the rate of material removal (RMR) of soda lime glass at flexible cutting condition. High speed cutting at micro meter level, extend of thermal softening might be prominent than the strain gradient strengthening. The purpose of this study was to explore the effects of high cutting speed end milling parameters on the surface texture of soda lime glass using uncoated carbide tool. The spindle speed, depth of cut and feed rate were varied from 20,000 to 40,000 rpm, 10 to 30 mm/min and 30 to 50 µm respectively. Mathematical model of roughness has been developed using Response Surface Methodology (RSM). Experimental verification confirmed that surface roughness (Ra) 0.38 µm is possible to achieve at increased RMR, 4.71 mm3/min.

Effect of High-speed Milling tool path strategies on the surface roughness of Stavax ESR mold insert machining

NASA Astrophysics Data System (ADS)

Mebrahitom, A.; Rizuan, D.; Azmir, M.; Nassif, M.

2016-02-01

High speed milling is one of the recent technologies used to produce mould inserts due to the need for high surface finish. It is a faster machining process where it uses a small side step and a small down step combined with very high spindle speed and feed rate. In order to effectively use the HSM capabilities, optimizing the tool path strategies and machining parameters is an important issue. In this paper, six different tool path strategies have been investigated on the surface finish and machining time of a rectangular cavities of ESR Stavax material. CAD/CAM application of CATIA V5 machining module for pocket milling of the cavities was used for process planning.

53. VIEW OF CRUSHED OXIDIZED ORE BIN FROM EAST. SHOWS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

53. VIEW OF CRUSHED OXIDIZED ORE BIN FROM EAST. SHOWS ACCESS STAIR TO FEED LEVEL; DUST COLLECTOR ON LEFT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

13. VIEW OF FIRST FLOOR, LOOKING NORTHWEST. AT LEFT IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. VIEW OF FIRST FLOOR, LOOKING NORTHWEST. AT LEFT IS A 'EUREKA O.K.' BAGGING SCALE (S. Howe Co., Silver Creek, New York). THE SUSPENSION-TYPE HOPPER SCALE WEIGHS BULK FEED AS IT DESCENDS INTO A BAG SECURED BY THE RING AT THE BASE OF THE SCALE. AT RIGHT, FINISHED PRODUCTS ARE READY FOR SALE. AT CENTER REAR IS ONE OF THE MILL'S TWO VERTICAL TWIN-SPIRAL MIXERS. Photographer: Jet T. Lowe, 1985 - Alexander's Grist Mill, Lock 37 on Ohio & Erie Canal, South of Cleveland, Valley View, Cuyahoga County, OH

40 CFR 406.74 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true [Reserved] 406.74 Section 406.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Animal Feed Subcategory § 406.74 [Reserved] ...

Part height control of laser metal additive manufacturing process

NASA Astrophysics Data System (ADS)

Pan, Yu-Herng

Laser Metal Deposition (LMD) has been used to not only make but also repair damaged parts in a layer-by-layer fashion. Parts made in this manner may produce less waste than those made through conventional machining processes. However, a common issue of LMD involves controlling the deposition's layer thickness. Accuracy is important, and as it increases, both the time required to produce the part and the material wasted during the material removal process (e.g., milling, lathe) decrease. The deposition rate is affected by multiple parameters, such as the powder feed rate, laser input power, axis feed rate, material type, and part design, the values of each of which may change during the LMD process. Using a mathematical model to build a generic equation that predicts the deposition's layer thickness is difficult due to these complex parameters. In this thesis, we propose a simple method that utilizes a single device. This device uses a pyrometer to monitor the current build height, thereby allowing the layer thickness to be controlled during the LMD process. This method also helps the LMD system to build parts even with complex parameters and to increase material efficiency.

Electrospray Thrusters for Attitude Control of a 1-U CubeSat

NASA Astrophysics Data System (ADS)

Timilsina, Navin

With a rapid increase in the interest in use of nanosatellites in the past decade, finding a precise and low-power-consuming attitude control system for these satellites has been a real challenge. In this thesis, it is intended to design and test an electrospray thruster system that could perform the attitude control of a 1-unit CubeSat. Firstly, an experimental setup is built to calculate the conductivity of different liquids that could be used as propellants for the CubeSat. Secondly, a Time-Of-Flight experiment is performed to find out the thrust and specific impulse given by these liquids and hence selecting the optimum propellant. On the other hand, a colloidal thruster system for a 1-U CubeSat is designed in Solidworks and fabricated using Lathe and CNC Milling Machine. Afterwards, passive propellant feeding is tested in this thruster system. Finally, the electronic circuit and wireless control system necessary to remotely control the CubeSat is designed and the final testing is performed. Among the propellants studied, Ethyl ammonium nitrate (EAN) was selected as the best propellant for the CubeSat. Theoretical design and fabrication of the thruster system was performed successfully and so was the passive propellant feeding test. The satellite was assembled for the final experiment but unfortunately the microcontroller broke down during the first test and no promising results were found out. However, after proving that one thruster works with passive feeding, it could be said that the ACS testing would have worked if we had performed vacuum compatibility tests for other components beforehand.

21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

Code of Federal Regulations, 2010 CFR

2010-04-01

...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

Code of Federal Regulations, 2012 CFR

2012-04-01

...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

The optimization study on the tool wear of carbide cutting tool during milling Carbon Fibre Reinforced (CFRP) using Response Surface Methodology (RSM)

NASA Astrophysics Data System (ADS)

Nor Khairusshima, M. K.; Hafiz Zakwan, B. Muhammad; Suhaily, M.; Sharifah, I. S. S.; Shaffiar, N. M.; Rashid, M. A. N.

2018-01-01

Carbon Fibre Reinforced Plastic (CFRP) composite has become one of famous materials in industry, such as automotive, aeronautics, aerospace and aircraft. CFRP is attractive due to its properties, which promising better strength and high specification of mechanical properties other than its high resistance to corrosion. Other than being abrasive material due to the carbon nature, CFRP is an anisotropic material, which the knowledge of machining metal and steel cannot be applied during machining CFRP. The improper technique and parameters used to machine CFRP may result in high tool wear. This paper is to study the tool wear of 8 mm diameter carbide cutting tool during milling CFRP. To predict the suitable cutting parameters within range of 3500-6220 (rev/min), 200-245 (mm/min), and 0.4-1.8 (mm) for cutting speed, speed, feed rate and depth of cut respectively, which produce optimized result (less tool wear), Response Surface Methodology (RSM) has been used. Based on the developed mathematical model, feed rate was identified as the primary significant item that influenced tool wear. The optimized cutting parameters are cutting speed, feed and depth of cut of 3500 rev/min, 200 mm/min and 0.5 mm, respectively, with tool wear of 0.0267 mm. It is also can be observed that as the cutting speed and feed rate increased the tool wear is increasing.

1. Building 15 west elevation oblique showing coal conveyor, chute ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Building 15 west elevation oblique showing coal conveyor, chute and hopper. Coal feeds boiler in Building 3. View looking SE. - John & James Dobson Carpet Mill (West Parcel), Building No. 15, 4041-4055 Ridge Avenue, Philadelphia, Philadelphia County, PA

Credit WCT. Original 2¾" x 2Y4" color negative is housed ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Original 2-¾" x 2-Y4" color negative is housed in the JPL Photography Laboratory, Pasadena, California. View shows JPL staff member John Morrow loading the grinder hopper. The hopper has a 10 mesh screen to filter out particles too large for the mill. Oxidizer is passed steadily to the hammers by a stainless steel feed screw. Oxidizer may be passed through the mill several times depending on the fineness required by a given propellant formula; the maximum charge is 130 pounds (59.0 Kg). The drum below the mill has an electrically conductive plastic liner which receives the ground oxidizer (JPL negative no. JPL10279AC, 27 January 1989) - Jet Propulsion Laboratory Edwards Facility, Oxidizer Grinder Building, Edwards Air Force Base, Boron, Kern County, CA

The BSE risk of processing meat and bone meal in nonruminant feed: a quantitative assessment for the Netherlands.

PubMed

de Vos, Clazien J; Heres, Lourens

2009-04-01

The total ban on use of meat and bone meal (MBM) in livestock feed has been very successful in reducing bovine spongiform encephalopathy (BSE) spread, but also implies a waste of high-quality proteins resulting in economic and ecological loss. Now that the BSE epidemic is fading out, a partial lifting of the MBM ban might be considered. The objective of this study was to assess the BSE risk for the Netherlands if MBM derived from animals fit for human consumption, i.e., category 3 MBM, would be used in nonruminant feed. A stochastic simulation model was constructed that calculates (1) the probability that infectivity of undetected BSE-infected cows ends up with calves and (2) the quantity of infectivity (Q(inf)) consumed by calves in case of such an incident. Three pathways were considered via which infectivity can reach cattle: (1) cross-contamination in the feed mill, (2) cross-contamination on the primary farm, and (3) pasture contamination. Model calculations indicate that the overall probability that infectivity ends up with calves is 3.2%. In most such incidents the Q(inf) is extremely small (median = 6.5 x 10(-12) ID(50); mean = 1.8 x 10(-4) ID(50)), corresponding to an average probability of 1.3 x 10(-4) that an incident results in >or=1 new BSE infections. Cross-contamination in the feed mill is the most risky pathway. Combining model results with Dutch BSE prevalence estimates for the coming years, it can be concluded that the BSE risk of using category 3 MBM derived from Dutch cattle in nonruminant feed is very low.

Investigation of the changes in aerosolization behavior between the jet-milled and spray-dried colistin powders through surface energy characterization

PubMed Central

Jong, Teresa; Li, Jian; Mortonx, David A.V.; Zhou, Qi (Tony); Larson, Ian

2016-01-01

This study aimed to investigate the surface energy factors behind improved aerosolization performance of spray-dried colistin powder formulations compared to those produced by jet-milling. Inhalable colistin powder formulations were produced by jet-milling or spray-drying (with or without L-leucine). Scanning electron micrographs showed the jet-milled particles had irregularly angular shapes, while the spray-dried particles were more spherical. Significantly higher fine particle fractions (FPFs) were measured for the spray-dried (43.8-49.6%) vs. the jet-milled formulation (28.4 %) from a Rotahaler at 60L/min; albeit the size distribution of the jet-milled powder was smaller. Surprisingly, addition of L-leucine in the spray drying feed-solution gave no significant improvement in FPF. As measured by inverse gas chromatography, spray-dried formulations had significantly (p<0.001) lower dispersive, specific and total surface energy values and more uniform surface energy distributions than the jet-milled powder. Interestingly, no significant difference was measured in the specific and total surface energy values between the spray-dried formulation with or without L-leucine. Based upon our previous findings in the self-assembling behavior of colistin in aqueous solution and the surface energy data obtained here, we propose the self-assembly of colistin molecules during spray-drying, contributed significantly to the reduction of surface free energy and the superior aerosolization performance. PMID:26886330

Process to improve boiler operation by supplemental firing with thermally beneficiated low rank coal

DOEpatents

Sheldon, Ray W.

2001-01-01

The invention described is a process for improving the performance of a commercial coal or lignite fired boiler system by supplementing its normal coal supply with a controlled quantity of thermally beneficiated low rank coal, (TBLRC). This supplemental TBLRC can be delivered either to the solid fuel mill (pulverizer) or directly to the coal burner feed pipe. Specific benefits are supplied based on knowledge of equipment types that may be employed on a commercial scale to complete the process. The thermally beneficiated low rank coal can be delivered along with regular coal or intermittently with regular coal as the needs require.

Energy use pattern in rice milling industries-a critical appraisal.

PubMed

Goyal, S K; Jogdand, S V; Agrawal, A K

2014-11-01

Rice milling industry is one of the most energy consuming industries. Like capital, labour and material, energy is one of the production factors which used to produce final product. In economical term, energy is demand-derived goods and can be regarded as intermediate good whose demand depends on the demand of final product. This paper deals with various types of energy pattern used in rice milling industries viz., thermal energy, mechanical energy, electrical energy and human energy. The important utilities in a rice mill are water, air, steam, electricity and labour. In a rice mill some of the operations are done manually namely, cleaning, sun drying, feeding paddy to the bucket elevators, weighing and packaging, etc. So the man-hours are also included in energy accounting. Water is used for soaking and steam generation. Electricity is the main energy source for these rice mills and is imported form the state electricity board grids. Electricity is used to run motors, pumps, blowers, conveyors, fans, lights, etc. The variations in the consumption rate of energy through the use of utilities during processing must also accounted for final cost of the finished product. The paddy milling consumes significant quantity of fuels and electricity. The major energy consuming equipments in the rice milling units are; boilers and steam distribution, blowers, pumps, conveyers, elevators, motors, transmission systems, weighing, etc. Though, wide variety of technologies has been evolved for efficient use of energy for various equipments of rice mills, so far, only a few have improved their energy efficiency levels. Most of the rice mills use old and locally available technologies and are also completely dependent on locally available technical personnel.

21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION...-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may... microorganisms in cane-sugar and/or beet-sugar mills as specified in paragraph (b) of this section. (b) They are...

A static model of a Sendzimir mill for use in shape control

NASA Astrophysics Data System (ADS)

Gunawardene, G. W. D. M.

The design of shape control systems is an area of current interest in the steel industry. Shape is defined as the internal stress distribution resulting from a transverse variation in the reduction of the strip thickness. The object of shape control is to adjust the mill so that the rolled strip is free from internal stresses. Both static and dynamic models of the mill are required for the control system design.The subject of this thesis is the static model of the Sendzimir cold rolling mill, which is a 1-2-3-4 type cluster mill. The static model derived enables shape profiles to be calculated for a given set of actuator positions, and is used to generate the steady state mill gains. The method of calculation of these shape profiles is discussed. The shape profiles obtained for different mill schedules are plotted against the distance across the strip. The corresponding mill gains are calculated and these relate the shape changes to the actuator changes. These mill gains are presented in the form of a square matrix, obtained by measuring shape at eight points across the strip.

Occupational hearing loss of market mill workers in the city of Accra, Ghana.

PubMed

Kitcher, Emmanuel D; Ocansey, Grace; Abaidoo, Benjamin; Atule, Alidu

2014-01-01

Noise induced hearing loss (NIHL) is an irreversible sensorineural hearing loss associated with exposure to high levels of excessive noise. Prevention measures are not well established in developing countries. This comparative cross sectional study aims to determine the prevalence of hearing loss in both a group of high risk workers and a control group and to assess their knowledge of the effects of noise on hearing health. A total of 101 market mill workers and 103 controls employed within markets in the city of Accra, Ghana, were evaluated using a structured questionnaire and pure tone audiometry. The questionnaire assessed factors including self-reported hearing loss, tinnitus, knowledge on the effects of noise on hearing health and the use of hearing protective devices. Pure tone audiometric testing was conducted for both mill workers and controls. Noise levels at the work premises of the mill workers and controls were measured. Symptoms of hearing loss were reported by 24 (23.76%) and 8 (7.7%) mill workers and controls respectively. Fifty-five (54.5%) and fifty-four (52.37%) mill workers and controls exhibited knowledge of the effects of noise on hearing health. Five (5.0%) mill workers used hearing protective devices. There was significant sensorineural hearing loss and the presence of a 4 kHz audiometric notch among mill workers when compared with controls for the mean thresholds of 2 kHz, 3 kHz and 4 kHz (P = 0. 001). The prevalence of hearing loss in the better hearing ears of the mill workers and controls was 24.8% and 4.8% respectively (P < 0.5). The prevalence of hearing loss, which may be characteristic of NIHL in the better hearing ears of the mill workers and controls was 24.8% and 4.8% respectively. The majority of mill workers did not use hearing protection.

Simultaneous analysis of coccidiostats and sulfonamides in non-target feed by HPLC-MS/MS and validation following the Commission Decision 2002/657/EC.

PubMed

Gavilán, Rosa Elvira; Nebot, Carolina; Patyra, Ewelina; Miranda, Jose Manuel; Franco, Carlos Manuel; Cepeda, Alberto

2018-05-02

Taking into consideration the maximum level for coccidiostats included in the European Regulation 574/2011 and the fact that the presence of residues of sulfonamides in non-target feed is forbidden, the aim of this article is to present an analytical method based on HPLC-MS/MS for the identification and quantification of sulfonamides and coccidiostats in non-target feeds. The method was validated following Decision 2002/657/EC and recovery, repeatability, and reproducibility were within the limits stablished in the Decision. For coccidiostats, the decision limit and detection capability were calculated for the different species taking into account the maximum level allowed in Regulation 574/2011. The applicability of the method was investigated in 50 feed samples collected from dairy farms, 50 obtained from feed mills, and 10 interlaboratory feed samples.

40 CFR 406.71 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Specialized definitions. 406.71 Section 406.71 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Animal Feed Subcategory § 406.71 Specialized definitions. For...

75 FR 59666 - Agricultural Swaps

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-28

..., grain sorghums, mill feeds, butter, eggs, Solanum tuberosum (Irish potatoes), wool, wool tops, fats and oils (including lard, tallow, cottonseed oil, peanut oil, soybean oil, and all other fats and oils... the Commodity Exchange Act (a) Permitting Eligible Swap Participants To Submit for Clearing and ICE...

75 FR 65586 - Agricultural Commodity Definition

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-26

... processed from cellulose before it becomes fiber. Category two would include high fructose corn syrup, but... wheat, cotton, rice, corn, oats, barley, rye, flaxseed, grain sorghum, mill feeds, butter, eggs, and... remained unchanged since the 1974 amendments: ``The term ``commodity'' means wheat, cotton, rice, corn...

Relationships between tissue properties and operational parameters of a dental handpiece during simulated cavity preparation

PubMed Central

Sun, Hongyan; Lau, Andrew; Heo, Young C; Lin, Lianshan; DeLong, Ralph

2013-01-01

A preliminary study was conducted on the development of an intelligent dental handpiece with functionality to detect subtle changes in mechanical properties of tooth tissue during milling. Such equipment would be able to adopt changes in cutting parameters and make real-time measurements to avoid tooth tissue damage caused by overexertion and overextension of the cutting tool. A modified dental handpiece, instrumented with strain gauges, microphone, displacement sensor, and air pressure sensor, was mounted to a linear movement table and used to mill three to four cavities in >50 bovine teeth. Extracted sound frequency and density were analyzed along with force, air pressure, and displacement for correlations and trends. Experimental results showed a high correlation (coefficient close to 0.7) between the feed force, the rotational frequency, and the averaged gray scale. These results could form the basis of a feedback control system to improve the safety of dental cutting procedures. This article is written in memory of Dr Hongyan Sun, who passed away in 2011 at a young age of 37. PMID:23554848

Relationships between tissue properties and operational parameters of a dental handpiece during simulated cavity preparation.

PubMed

Sun, Hongyan; Lau, Andrew; Heo, Young C; Lin, Lianshan; Delong, Ralph; Fok, Alex

2013-01-01

A preliminary study was conducted on the development of an intelligent dental handpiece with functionality to detect subtle changes in mechanical properties of tooth tissue during milling. Such equipment would be able to adopt changes in cutting parameters and make real-time measurements to avoid tooth tissue damage caused by overexertion and overextension of the cutting tool. A modified dental handpiece, instrumented with strain gauges, microphone, displacement sensor, and air pressure sensor, was mounted to a linear movement table and used to mill three to four cavities in >50 bovine teeth. Extracted sound frequency and density were analyzed along with force, air pressure, and displacement for correlations and trends. Experimental results showed a high correlation (coefficient close to 0.7) between the feed force, the rotational frequency, and the averaged gray scale. These results could form the basis of a feedback control system to improve the safety of dental cutting procedures. This article is written in memory of Dr Hongyan Sun, who passed away in 2011 at a young age of 37.

Chip morphology as a performance predictor during high speed end milling of soda lime glass

NASA Astrophysics Data System (ADS)

Bagum, M. N.; Konneh, M.; Abdullah, K. A.; Ali, M. Y.

2018-01-01

Soda lime glass has application in DNA arrays and lab on chip manufacturing. Although investigation revealed that machining of such brittle material is possible using ductile mode under controlled cutting parameters and tool geometry, it remains a challenging task. Furthermore, ability of ductile machining is usually assed through machined surface texture examination. Soda lime glass is a strain rate and temperature sensitive material. Hence, influence on attainment of ductile surface due to adiabatic heat generated during high speed end milling using uncoated tungsten carbide tool is investigated in this research. Experimental runs were designed using central composite design (CCD), taking spindle speed, feed rate and depth of cut as input variable and tool-chip contact point temperature (Ttc) and the surface roughness (Rt) as responses. Along with machined surface texture, Rt and chip morphology was examined to assess machinability of soda lime glass. The relation between Ttc and chip morphology was examined. Investigation showed that around glass transition temperature (Tg) ductile chip produced and subsequently clean and ductile final machined surface produced.

Enhancing nutritiousness of lamb meat and preventing selenium deficiency.

USDA-ARS?s Scientific Manuscript database

Lamb meat is a naturally flavorful and nutritious product. Our research indicates that feeding a specific wheat-milling coproduct will enhance the nutritiousness of lamb, potentially add monetary value to lamb, and prevent Se deficiency. Selenium is an essential micromineral, and Se supplementation ...

72. DETAIL VIEW OF TRAM SUSPENSION CABLE OILING CAR. NOTE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

72. DETAIL VIEW OF TRAM SUSPENSION CABLE OILING CAR. NOTE CIRCULAR TRACTION CABLE CLAMP IN CENTER AND OIL FEED TO CABLE BETWEEN TWO RIGHT-HAND WHEELS. OIL REDUCED FRICTION AND RUST. - Shenandoah-Dives Mill, 135 County Road 2, Silverton, San Juan County, CO

Characterization of Scots pine stump-root biomass as feed-stock for gasification.

PubMed

Eriksson, Daniel; Weiland, Fredrik; Hedman, Henry; Stenberg, Martin; Öhrman, Olov; Lestander, Torbjörn A; Bergsten, Urban; Öhman, Marcus

2012-01-01

The main objective was to explore the potential for gasifying Scots pine stump-root biomass (SRB). Washed thin roots, coarse roots, stump heartwood and stump sapwood were characterized (solid wood, milling and powder characteristics) before and during industrial processing. Non-slagging gasification of the SRB fuels and a reference stem wood was successful, and the gasification parameters (synthesis gas and bottom ash characteristics) were similar. However, the heartwood fuel had high levels of extractives (≈19%) compared to the other fuels (2-8%) and thereby ≈16% higher energy contents but caused disturbances during milling, storage, feeding and gasification. SRB fuels could be sorted automatically according to their extractives and moisture contents using near-infrared spectroscopy, and their amounts and quality in forests can be predicted using routinely collected stand data, biomass functions and drill core analyses. Thus, SRB gasification has great potential and the proposed characterizations exploit it. Copyright © 2011 Elsevier Ltd. All rights reserved.

Machinability of experimental Ti-Ag alloys.

PubMed

Kikuchi, Masafumi; Takahashi, Masatoshi; Okuno, Osamu

2008-03-01

This study investigated the machinability of experimental Ti-Ag alloys (5, 10, 20, and 30 mass% Ag) as a new dental titanium alloy candidate for CAD/CAM use. The alloys were slotted with a vertical milling machine and carbide square end mills under two cutting conditions. Machinability was evaluated through cutting force using a three-component force transducer fixed on the table of the milling machine. The horizontal cutting force of the Ti-Ag alloys tended to decrease as the concentration of silver increased. Values of the component of the horizontal cutting force perpendicular to the feed direction for Ti-20% Ag and Ti-30% Ag were more than 20% lower than those for titanium under both cutting conditions. Alloying with silver significantly improved the machinability of titanium in terms of cutting force under the present cutting conditions.

Predictive Surface Roughness Model for End Milling of Machinable Glass Ceramic

NASA Astrophysics Data System (ADS)

Mohan Reddy, M.; Gorin, Alexander; Abou-El-Hossein, K. A.

2011-02-01

Advanced ceramics of Machinable glass ceramic is attractive material to produce high accuracy miniaturized components for many applications in various industries such as aerospace, electronics, biomedical, automotive and environmental communications due to their wear resistance, high hardness, high compressive strength, good corrosion resistance and excellent high temperature properties. Many research works have been conducted in the last few years to investigate the performance of different machining operations when processing various advanced ceramics. Micro end-milling is one of the machining methods to meet the demand of micro parts. Selecting proper machining parameters are important to obtain good surface finish during machining of Machinable glass ceramic. Therefore, this paper describes the development of predictive model for the surface roughness of Machinable glass ceramic in terms of speed, feed rate by using micro end-milling operation.

Flight of the Chinese white pine beetle (Coleoptera: Scolytidae) in relation to sex, body weight and energy reserve.

PubMed

Chen, H; Li, Z; Bu, S H; Tian, Z Q

2011-02-01

The flight distance, flight time and individual flight activities of males and females of Dendroctonus armandi were recorded during 96-h flight trials using a flight mill system. The body weight, glucose, glycogen and lipid content of four treatments (naturally emerged, starved, phloem-fed and water-fed) were compared among pre-flight, post-flight and unflown controls. There was no significant difference between males and females in total flight distance and flight time in a given 24-h period. The flight distance and flight time of females showed a significant linear decline as the tethered flying continued, but the sustained flight ability of females was better than that of males. The females had higher glycogen and lipid content than the males; however, there was no significant difference between both sexes in glucose content. Water-feeding and phloem-feeding had significant effects on longevity, survival days and flight potential of D. armandi, which resulted in longer feeding days, poorer flight potential and lower energy substrate content. Our results demonstrate that flight distances in general do not differ between water-fed and starved individuals, whereas phloem-fed females and males fly better than water-fed and starved individuals.

Effects of Adult Feeding and Overwintering Conditions on Energy Reserves and Flight Performance of Emerald Ash Borer (Coleoptera: Buprestidae).

PubMed

Tussey, Dylan A; Aukema, Brian H; Charvoz, Anthony M; Venette, Robert C

2018-06-06

Emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), an invasive beetle from Asia, spreads through human-mediated movement and active flight. The effects of adult feeding and overwintering conditions on A. planipennis energy reserves (e.g., lipid, glycogen, and sugars) and flight are poorly understood. We conjectured that the potential energetic demands associated with the production of cryoprotectants might affect dispersal capacity and partially explain slower spread of A. planipennis in Minnesota than in the other states. Two studies sought to measure the effects of adult feeding on lipid content and flight capacity. Adult A. planipennis were fed shamel ash, Fraxinus uhdei Wenzig, leaves for 0-20 d after emergence, and half were flown on a custom flight mill for 24 h, before being frozen for comparative lipid analysis with a control group. The second study compared the effects of adult feeding on energy reserves and flight capacity of A. planipennis that were originally from St. Paul, Minnesota but overwintered in infested logs placed in Grand Rapids, Minnesota (low winter temperature, -34°C) or St. Paul, Minnesota (-26.3°C). Live adults consumed foliage at a constant rate, but lipid content (percentage of fresh mass) did not change with increases in feeding or flight. Adult glycogen content declined with flight and increased only slightly with feeding. Overwintering location affected survival rates but not energy reserves or flight capacity. These results suggest that the flight capacity of A. planipennis is largely determined before emergence, with no differences in energy reserves after cryoprotectant investment.

40 CFR 406.75 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Standards of performance for new sources. 406.75 Section 406.75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Animal Feed Subcategory § 406.75...

40 CFR 406.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Pretreatment standards for new sources. 406.76 Section 406.76 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Animal Feed Subcategory § 406.76 Pretreatment...

Effects of various diets on the calcium and phosphorus composition of mealworms (Tenebrio molitor larvae) and superworms (Zophobas morio larvae).

PubMed

Latney, La'Toya V; Toddes, Barbara D; Wyre, Nicole R; Brown, Dorothy C; Michel, Kathryn E; Briscoe, Johanna A

2017-02-01

OBJECTIVE To evaluate whether the nutritive quality of Tenebrio molitor larvae and Zophobas morio larvae, which are commonly cultured as live food sources, is influenced by 4 commercially available diets used as nutritional substrates; identify which diet best improved calcium content of larvae; and identify the feeding time interval that assured the highest calcium intake by larvae. ANIMALS 2,000 Zophobas morio larvae (ie, superworms) and 7,500 Tenebrio molitor larvae (ie, mealworms). PROCEDURES Larvae were placed in control and diet treatment groups for 2-, 7-, and 10-day intervals. Treatment diets were as follows: wheat millings, avian hand feeding formula, organic avian mash diet, and a high-calcium cricket feed. Control groups received water only. After treatment, larvae were flash-frozen live with liquid nitrogen in preparation for complete proximate and mineral analyses. Analyses for the 2-day treatment group were performed in triplicate. RESULTS The nutrient composition of the high-calcium cricket feed groups had significant changes in calcium content, phosphorus content, and metabolizable energy at the 2-day interval, compared with other treatment groups, for both mealworms and superworms. Calcium content and calcium-to-phosphorus ratios for larvae in the high-calcium cricket feed group were the highest among the diet treatments for all treatment intervals and for both larval species. CONCLUSIONS AND CLINICAL RELEVANCE A 2-day interval with the high-calcium cricket feed achieved a larval nutrient composition sufficient to meet National Research Council dietary calcium recommendations for nonlactating rats. Mealworm calcium composition reached 2,420 g/1,000 kcal at 48 hours, and superworm calcium composition reached 2,070g/1,000 kcal at 48 hours. These findings may enable pet owners, veterinarians, insect breeders, and zoo curators to optimize nutritive content of larvae fed to insectivorous animals.

Effect of pelleting on survival of porcine epidemic diarrhea virus-contaminated feed.

PubMed

Cochrane, R A; Schumacher, L L; Dritz, S S; Woodworth, J C; Huss, A R; Stark, C R; DeRouchey, J M; Tokach, M D; Goodband, R D; Bia, J; Chen, Q; Zhang, J; Gauger, P C; Derscheid, R J; Magstadt, D R; Main, R G; Jones, C K

2017-03-01

Porcine epidemic diarrhea virus (PEDV) is a heat-sensitive virus that has devastated the U.S. swine industry. Because of its heat sensitivity, we hypothesized that a steam conditioner and pellet mill mimicking traditional commercial thermal processing may mitigate PEDV infectivity. Pelleting, a common feed processing method, includes the use of steam and shear forces, resulting in increased temperature of the processed feed. Two thermal processing experiments were designed to determine if different pellet mill conditioner retention times and temperatures would impact PEDV quantity and infectivity by analysis of quantitative reverse transcription PCR and bioassay. In Exp. 1, a 3 × 3 × 2 factorial design was used with 3 pelleting temperatures (68.3, 79.4, and 90.6°C), 3 conditioning times (45, 90, or 180 s), and 2 doses of viral inoculation (low, 1 × 10 tissue culture infectious dose (the concentration used to see cytopathic effect in 50% of the cells)/g, or high, 1 × 10 tissue culture infectious dose/g). Noninoculated and PEDV-inoculated unprocessed mash were used as controls. The low-dose PEDV-infected mash had 6.8 ± 1.8 cycle threshold (Ct) greater ( < 0.05) PEDV than the high-dose mash. Regardless of time or temperature, pelleting reduced ( < 0.05) the quantity of detectable viral PEDV RNA compared with the PEDV-inoculated unprocessed mash. Fecal swabs from pigs inoculated with the PEDV-positive unprocessed mash, regardless of dose, were clinically PEDV positive from 2 to 7 d (end of the trial) after inoculation. However, if either PEDV dose of inoculated feed was pelleted at any of the 9 tested conditioning time × temperature combinations, no PEDV RNA was detected in fecal swabs or cecum content. Based on Exp. 1 results, a second experiment was developed to determine the impact of lower processing temperatures on PEDV quantity and infectivity. In Exp. 2, PEDV-inoculated feed was pelleted at 1 of 5 conditioning temperatures (37.8, 46.1, 54.4, 62.8, and 71.1°C) for 30 s. The 5 increasing processing temperatures led to feed with respective mean Ct values of 32.5, 34.6, 37.0, 36.5, and 36.7, respectively. All samples had detectable PEDV RNA. However, infectivity was detected by bioassay only in pigs from the 37.8 and 46.1°C conditioning temperatures. Experiment 2 results suggest conditioning and pelleting temperatures above 54.4°C could be effective in reducing the quantity and infectivity of PEDV in swine feed. However, additional research is needed to prevent subsequent recontamination after pelleting as it is a point-in-time mitigation step.

Evaluation of a Biological Pathogen Decontamination Protocol for Animal Feed Mills.

PubMed

Huss, Anne R; Cochrane, Roger A; Deliephan, Aiswariya; Stark, Charles R; Jones, Cassandra K

2015-09-01

Animal feed and ingredients are potential vectors of pathogenic bacteria. Contaminated ingredients can contaminate facility equipment, leading to cross-contamination of other products. This experiment was conducted to evaluate a standardized protocol for decontamination of an animal feed manufacturing facility using Enterococcus faecium (ATCC 31282) as an indicator. A pelleted swine diet inoculated with E. faecium was manufactured, and environmental samples (swabs, replicate organism detection and counting plates, and air samples) were collected (i) before inoculation (baseline data), (ii) after production of inoculated feed, (iii) after physical removal of organic material using pressurized air, (iv) after application of a chemical sanitizer containing a quaternary ammonium-glutaraldehyde blend, (v) after application of a chemical sanitizer containing sodium hypochlorite, (vi) after facility heat-up to 60 8 C for 24 h, (vii) for 48 h, and (viii) for 72 h. Air samples collected outside the facility confirmed pathogen containment; E. faecium levels were equal to or lower than baseline levels at each sample location. The decontamination step and its associated interactions were the only variables that affected E. faecium incidence (P < 0.0001 versus P > 0.22). After production of the inoculated diet, 85.7% of environmental samples were positive for E. faecium. Physical cleaning of equipment had no effect on contamination (P = 0.32). Chemical cleaning with a quaternary ammonium-glutaraldehyde blend and sodium hypochlorite each significantly reduced E. faecium contamination (P < 0.0001) to 28.6 and 2.4% of tested surfaces, respectively. All samples were negative for E. faecium after 48 h of heating. Both wet chemical cleaning and facility heating but not physical cleaning resulted in substantial E. faecium decontamination. These results confirmed both successful containment and decontamination of biological pathogens in the tested pilot-scale feed mill.

40 CFR 63.2872 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... NESHAP General Provisions. (c) In this section as follows: Accounting month means a time interval defined... solvent from the extracted meal. Oilseeds processed in a conventional desolventizer produce crude vegetable oil and crude meal products, such as animal feed. Corn germ dry milling means a source that...

In Vitro Assays for Assessment of Androgenic and Estrogenic Activity of Defined Mixtures and Complex Environmental Samples

EPA Science Inventory

Point sources of endocrine active compounds to aquatic environments such as waste water treatment plants, pulp and paper mills, and animal feeding operations invariably contain complex mixtures of chemicals. The current study investigates the use of targeted in vitro assays des...

In vitro assays for assessment of androgenic and estrogenic activity of defined mixtures and complex environment samples

EPA Science Inventory

Point sources of potentially endocrine active compounds to aquatic environments such as waste water treatment plants, pulp and paper mills, and animal feeding operations invariably contain complex mixtures of chemicals. The current study investigates the use of targeted in vitro ...

9 CFR 149.1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the feed mill to the pork production site. Food Safety and Inspection Service (FSIS). The Food Safety... Administrator, Food Safety and Inspection Service, or any person authorized to act for the Administrator. FSIS program employee. Any individual employed by or acting as an agent on behalf of the Food Safety and...

9 CFR 149.1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the feed mill to the pork production site. Food Safety and Inspection Service (FSIS). The Food Safety... Administrator, Food Safety and Inspection Service, or any person authorized to act for the Administrator. FSIS program employee. Any individual employed by or acting as an agent on behalf of the Food Safety and...

9 CFR 149.1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the feed mill to the pork production site. Food Safety and Inspection Service (FSIS). The Food Safety... Administrator, Food Safety and Inspection Service, or any person authorized to act for the Administrator. FSIS program employee. Any individual employed by or acting as an agent on behalf of the Food Safety and...

40 CFR 63.2872 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... vegetable oil and crude meal products, such as animal feed. Corn germ dry milling means a source that processes corn germ that has been separated from the other corn components using a “dry” process of... to solvent recovery equipment such as extractors, desolventizer-toasters/dryer-coolers, flash...

40 CFR 63.2872 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... vegetable oil and crude meal products, such as animal feed. Corn germ dry milling means a source that processes corn germ that has been separated from the other corn components using a “dry” process of... to solvent recovery equipment such as extractors, desolventizer-toasters/dryer-coolers, flash...

40 CFR 63.2872 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... vegetable oil and crude meal products, such as animal feed. Corn germ dry milling means a source that processes corn germ that has been separated from the other corn components using a “dry” process of... to solvent recovery equipment such as extractors, desolventizer-toasters/dryer-coolers, flash...

Economic analysis for commingling effects of insect activity in the elevator boot area

USDA-ARS?s Scientific Manuscript database

Boot areas in commercial grain elevators and feed mills contribute to commingling of insects with grain that moves through the elevator leg. A partial budget and stochastic dominance model was developed to improve pest management decision-making and risk analysis assessment from commingling effects ...

Characterizing germinated brown rice milk beverage processes using green technologies

USDA-ARS?s Scientific Manuscript database

Rice feeds approximately half the world’s population. However, due to milling losses, white rice is a poor source of vitamins and minerals. Brown rice is nutritionally superior yet oils and rancidity can be problematic regarding storage and organoleptics. Germinating brown rice is known to increase ...

36. VIEW OF FRAMING BENT BETWEEN SECONDARY THICKENER No. 3 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. VIEW OF FRAMING BENT BETWEEN SECONDARY THICKENER No. 3 AND PRIMARY THICKENER No. 2 FROM WEST. NOTE MECHANISM ON PRIMARY No. 2 ON LEFT, BARREN SOLUTION FEED PIPE AT LOWER RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

49. VIEW FROM WEST OF DUST COLLECTOR BLOWER LOCATED AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

49. VIEW FROM WEST OF DUST COLLECTOR BLOWER LOCATED AT CRUSHED OXIDIZED ORE BIN FEED LEVEL. THE ROASTER IS BEYOND AND THE MACHINE SHOP IS ON THE TRAM TERRACE, UPPER RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Milled cereal straw accelerates earthworm (Lumbricus terrestris) growth more than selected organic amendments.

PubMed

Sizmur, Tom; Martin, Elodie; Wagner, Kevin; Parmentier, Emilie; Watts, Chris; Whitmore, Andrew P

2017-05-01

Earthworms benefit agriculture by providing several ecosystem services. Therefore, strategies to increase earthworm abundance and activity in agricultural soils should be identified, and encouraged. Lumbricus terrestris earthworms primarily feed on organic inputs to soils but it is not known which organic amendments are the most effective for increasing earthworm populations. We conducted earthworm surveys in the field and carried out experiments in single-earthworm microcosms to determine the optimum food source for increasing earthworm biomass using a selection of crop residues and organic wastes available to agriculture. We found that although farmyard manure increased earthworm populations more than cereal straw in the field, straw increased earthworm biomass more than manures when milled and applied to microcosms. Earthworm growth rates were positively correlated with the calorific value of the amendment and straw had a much higher calorific value than farmyard manure, greenwaste compost, or anaerobic digestate. Reducing the particle size of straw by milling to <3 mm made the energy in the straw more accessible to earthworms. The benefits and barriers to applying milled straw to arable soils in the field are discussed.

Assessment of a New Silicon Carbide Tubular Honeycomb Membrane for Treatment of Olive Mill Wastewaters

PubMed Central

Fraga, Maria C.; Sanches, Sandra; Crespo, João G.; Pereira, Vanessa J.

2017-01-01

Extremely high removals of total suspended solids and oil and grease were obtained when olive mill wastewaters were filtered using new silicon carbide tubular membranes. These new membranes were used at constant permeate flux to treat real olive mill wastewaters at pilot scale. The filtration conditions were evaluated and optimized in terms of the selection of the permeate flux and flux maintenance strategies employed—backpulsing and backwashing—in order to reduce fouling formation. The results obtained reveal that the combination of backpulses and backwashes helps to maintain the permeate flux, avoids transmembrane pressure increase and decreases the cake resistance. Moreover, membrane cleaning procedures were compared and the main agents responsible for fouling formation identified. Results also show that, under total recirculation, despite an increased concentration of pollutants in the feed stream, the quality of the permeate is maintained. Membrane filtration using silicon carbide membranes is an effective alternative to dissolved air flotation and can be applied efficiently to remove total suspended solids and oil and grease from olive mill wastewaters. PMID:28264453

Assessment of a New Silicon Carbide Tubular Honeycomb Membrane for Treatment of Olive Mill Wastewaters.

PubMed

Fraga, Maria C; Sanches, Sandra; Crespo, João G; Pereira, Vanessa J

2017-02-27

Extremely high removals of total suspended solids and oil and grease were obtained when olive mill wastewaters were filtered using new silicon carbide tubular membranes. These new membranes were used at constant permeate flux to treat real olive mill wastewaters at pilot scale. The filtration conditions were evaluated and optimized in terms of the selection of the permeate flux and flux maintenance strategies employed-backpulsing and backwashing-in order to reduce fouling formation. The results obtained reveal that the combination of backpulses and backwashes helps to maintain the permeate flux, avoids transmembrane pressure increase and decreases the cake resistance. Moreover, membrane cleaning procedures were compared and the main agents responsible for fouling formation identified. Results also show that, under total recirculation, despite an increased concentration of pollutants in the feed stream, the quality of the permeate is maintained. Membrane filtration using silicon carbide membranes is an effective alternative to dissolved air flotation and can be applied efficiently to remove total suspended solids and oil and grease from olive mill wastewaters.

Flank wears Simulation by using back propagation neural network when cutting hardened H-13 steel in CNC End Milling

NASA Astrophysics Data System (ADS)

Hazza, Muataz Hazza F. Al; Adesta, Erry Y. T.; Riza, Muhammad

2013-12-01

High speed milling has many advantages such as higher removal rate and high productivity. However, higher cutting speed increase the flank wear rate and thus reducing the cutting tool life. Therefore estimating and predicting the flank wear length in early stages reduces the risk of unaccepted tooling cost. This research presents a neural network model for predicting and simulating the flank wear in the CNC end milling process. A set of sparse experimental data for finish end milling on AISI H13 at hardness of 48 HRC have been conducted to measure the flank wear length. Then the measured data have been used to train the developed neural network model. Artificial neural network (ANN) was applied to predict the flank wear length. The neural network contains twenty hidden layer with feed forward back propagation hierarchical. The neural network has been designed with MATLAB Neural Network Toolbox. The results show a high correlation between the predicted and the observed flank wear which indicates the validity of the models.

A Study of Chip Formation Feedrates of Various Steels in Low-Speed Milling Process

NASA Astrophysics Data System (ADS)

Prasetyo, L.; Tauviqirrahman, M.; Rusnaldy

2017-05-01

Milling is a process of metal removal by feeding the workpiece a rotating multitoothed cutter. The objective of the study was to investigate the chip characteristics (chip length, width, and thickness) during the milling process by varying the feedrates and the types of materials used based on an experimental approach. The chosen materials were AISI 1020, AISI 1045, AISI 1090, AISI D2, and AISI 4340 with a high-speed steel (HSS) as a cutter. In this work, the feedrates were varied of 5, 10, and 15 mm/minutes with the depth of cut of 0.5 mm and a low spindle speed of 70 rpm. The results show that, in general, increasing the feedrate will lead to the growth of chip length, width, and thickness for all types of materials used. Also, related to the chip shape, AISI 1020 produces the discontinuous chip which can be related to its hardness value.

41. VIEW NORTH OF UPPER LEVEL OF CRUSHER ADDITION. DINGS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. VIEW NORTH OF UPPER LEVEL OF CRUSHER ADDITION. DINGS MAGNETIC PULLEY AT CENTER. ALSO SHOWS 100-TON CRUSHED UNOXIDIZED ORE BIN (RIGHT), PULLEY FORM 18 INCH BELT CONVEYOR CRUSHED OXIDIZED ORE BIN FEED AND STEPHENSADAMSON 25 TON/HR BUCKET ELEVATOR (UPPER CENTER). THE UPPER PORTION OF THE SAMPLING ELEVATOR IS ABOVE THE MAGNETIC PULLEY (CENTER LEFT) WITH THE ROUTE OF THE 16 INCH BELT CONVEYOR FINES FEED TO CRUSHED OXIDIZED ORE BIN TO ITS LEFT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Selective enrichment of a methanol-utilizing consortium using pulp & paper mill waste streams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gregory R. Mockos; William A. Smith; Frank J. Loge

Efficient utilization of carbon inputs is critical to the economic viability of the current forest products sector. Input carbon losses occur in various locations within a pulp mill, including losses as volatile organics and wastewater . Opportunities exist to capture this carbon in the form of value-added products such as biodegradable polymers. Waste activated sludge from a pulp mill wastewater facility was enriched for 80 days for a methanol-utilizing consortium with the goal of using this consortium to produce biopolymers from methanol-rich pulp mill waste streams. Five enrichment conditions were utilized: three high-methanol streams from the kraft mill foul condensatemore » system, one methanol-amended stream from the mill wastewater plant, and one methanol-only enrichment. Enrichment reactors were operated aerobically in sequencing batch mode at neutral pH and 25°C with a hydraulic residence time and a solids retention time of four days. Non-enriched waste activated sludge did not consume methanol or reduce chemical oxygen demand. With enrichment, however, the chemical oxygen demand reduction over 24 hour feed/decant cycles ranged from 79 to 89 %, and methanol concentrations dropped below method detection limits. Neither the non-enriched waste activated sludge nor any of the enrichment cultures accumulated polyhydroxyalkanoates (PHAs) under conditions of nitrogen sufficiency. Similarly, the non-enriched waste activated sludge did not accumulate PHAs under nitrogen limited conditions. By contrast, enriched cultures accumulated PHAs to nearly 14% on a dry weight basis under nitrogen limited conditions. This indicates that selectively-enriched pulp mill waste activated sludge can serve as an inoculum for PHA production from methanol-rich pulp mill effluents.« less

Selective Enrichment of a Methanol-Utilizing Consortium Using Pulp and Paper Mill Waste Streams

NASA Astrophysics Data System (ADS)

Mockos, Gregory R.; Smith, William A.; Loge, Frank J.; Thompson, David N.

Efficient utilization of carbon inputs is critical to the economic viability of the current forest products sector. Input carbon losses occur in various locations within a pulp mill, including losses as volatile organics and wastewater. Opportunities exist to capture this carbon in the form of value-added products such as biodegradable polymers. Wasteactivated sludge from a pulp mill wastewater facility was enriched for 80 days for a methanol-utilizing consortium with the goal of using this consortium to produce biopolymers from methanol-rich pulp mill waste streams. Five enrichment conditions were utilized: three high-methanol streams from the kraft mill foul condensate system, one methanol-amended stream from the mill wastewater plant, and one methanol-only enrichment. Enrichment reactors were operated aerobically in sequencing batch mode at neutral pH and 25°C with a hydraulic residence time and a solids retention time of 4 days. Non-enriched waste activated sludge did not consume methanol or reduce chemical oxygen demand. With enrichment, however, the chemical oxygen demand reduction over 24-h feed/ decant cycles ranged from 79 to 89%, and methanol concentrations dropped below method detection limits. Neither the non-enriched waste-activated sludge nor any of the enrichment cultures accumulated polyhydroxyalkanoates (PHAs) under conditions of nitrogen sufficiency. Similarly, the non-enriched waste activated sludge did not accumulate PHAs under nitrogen-limited conditions. By contrast, enriched cultures accumulated PHAs to nearly 14% on a dry weight basis under nitrogen-limited conditions. This indicates that selectively enriched pulp mill waste activated sludge can serve as an inoculum for PHA production from methanol-rich pulp mill effluents.

Fumonisins B1 and B2 in the corn-milling process and corn-based products, and evaluation of estimated daily intake.

PubMed

Savi, Geovana D; Piacentini, Karim C; Marchi, Djeini; Scussel, Vildes M

2016-01-01

The distribution of fumonisins (FBs: FB1 and FB2) in the corn-milling process and in corn-based products, as well as daily intake estimates for the Brazilian population were evaluated. Among corn fractions samples, corn meal had the highest mean concentration of FB1 (1305 µg kg(-1)) and FB2 (651 µg kg(-1)) and a distribution factors of 452% and 256% in relation to corn grain, respectively. On the other hand, the distribution factor of FB1 and FB2 in corn flour was found to be 144% and 88% respectively, which demonstrates that fumonisins in this fraction were reduced compared with corn grain. As a result, almost half the corn meal samples (47%) would be non-compliant with future Brazilian regulation (2017) for fumonisins. However, corn-based products, such as corn flakes and popcorn, were in compliance with the regulation. The average probable daily intake and maximum probable daily intake of fumonisins estimated for the Santa Catarina state (Brazil) population were below the provisional maximum tolerable daily intake of 2 µg kg(-1) body weight day(-1) for all corn samples. Despite this, the adoption of practices to control the occurrence of fumonisins should be applied to the corn-milling fractions that may contain a higher concentration of this toxin, such as corn meal, often used for animal feed in Brazil.

40 CFR 23.8 - Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. 23.8 Section 23.8 Protection of Environment... Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. Unless the Administrator...

40 CFR 23.8 - Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. 23.8 Section 23.8 Protection of Environment... Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. Unless the Administrator...

40 CFR 23.8 - Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. 23.8 Section 23.8 Protection of Environment... Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. Unless the Administrator...

40 CFR 23.8 - Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. 23.8 Section 23.8 Protection of Environment... Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. Unless the Administrator...

40 CFR 23.8 - Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Timing of Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. 23.8 Section 23.8 Protection of Environment... Administrator's action under Uranium Mill Tailings Radiation Control Act of 1978. Unless the Administrator...

Effect of replacing calcium salts of palm oil distillate with rapeseed oil, milled or whole rapeseeds on milk fatty-acid composition in cows fed maize silage-based diets.

PubMed

Givens, D I; Kliem, K E; Humphries, D J; Shingfield, K J; Morgan, R

2009-07-01

Inclusion of rapeseed feeds in dairy cow diets has the potential to reduce milk fat saturated fatty acid (SFA) and increase cis-monounsaturated fatty acid (cis-MUFA) content, but effectiveness may depend on the form in which the rapeseed is presented. Four mid-lactation Holstein dairy cows were allocated to four maize silage-based dietary treatments according to a 4 × 4 Latin Square design, with 28-day experimental periods. Treatments consisted of a control diet (C) containing 49 g/kg dry matter (DM) of calcium salts of palm oil distillate (CPO), or 49 g/kg DM of oil supplied as whole rapeseeds (WR), rapeseeds milled with wheat (MR) or rapeseed oil (RO). Replacing CPO with rapeseed feeds had no effect (P > 0.05) on milk fat and protein content, while milk yields were higher (P < 0.05) for RO and MR compared with WR (37.1, 38.1 and 34.3 kg/day, respectively). Substituting CPO with RO or MR reduced (P < 0.05) milk fat total SFA content (69.6, 55.6, 71.7 and 61.5 g/100 g fatty acids for C, RO, WR and MR, respectively) and enhanced (P < 0.05) milk cis-9 18:1 MUFA concentrations (corresponding values 18.6, 24.3, 17.0 and 23.0 g/100 g fatty acids) compared with C and WR. Treatments RO and MR also increased (P < 0.05) milk trans-MUFA content (4.4, 6.8, 10.5 g/100 g fatty acids, C, MR and RO, respectively). A lack of significant changes in milk fat composition when replacing CPO with WR suggests limited bioavailability of fatty acids in intact rapeseeds. In conclusion, replacing a commercial palm oil-based fat supplement in the diet with milled rapeseeds or rapeseed oil represented an effective strategy to alter milk fatty acid composition with the potential to improve human health. Inclusion of processed rapeseeds offered a good compromise for reducing milk SFA and increasing cis-MUFA, whilst minimising milk trans-MUFA and negative effects on animal performance.

Survey on Urinary Levels of Aflatoxins in Professionally Exposed Workers

PubMed Central

Ferri, Fulvio; Brera, Carlo; De Santis, Barbara; Fedrizzi, Giorgio; Bacci, Tiziana; Bedogni, Lorena; Capanni, Sauro; Collini, Giorgia; Crespi, Enrica; Debegnach, Francesca; Ferdenzi, Patrizia; Gargano, Angelo; Gattei, Daniela; Luberto, Ferdinando; Magnani, Ines; Magnani, Massimo Giuseppe; Mancuso, Pamela; Menotta, Simonetta; Mozzanica, Stefania; Olmi, Milva; Ombrini, Giuseppe; Sala, Orietta; Soricelli, Sabina; Vicentini, Massimo; Giorgi Rossi, Paolo

2017-01-01

Feed mill workers may handle or process maize contaminated with aflatoxins (AFs). This condition may lead to an unacceptable intake of toxins deriving from occupational exposure. This study assessed the serological and urinary levels of AFs in workers exposed to potentially contaminated dusts in two mills. From March to April 2014, blood and urine samples were collected, on Monday and Friday morning of the same working week from 29 exposed workers and 30 non-exposed controls. AFs (M1, G2, G1, B1, B2) and aflatoxicol (AFOH) A were analyzed. Each subject filled in a questionnaire to evaluate potential food-borne exposures to mycotoxins. AFs contamination in environmental dust was measured in both plants. No serum sample was found to be positive. Seventy four percent of urine samples (73.7%) revealed AFM1 presence. AFM1 mean concentration was 0.035 and 0.027 ng/mL in exposed and non-exposed workers, respectively (p = 0.432); the concentration was slightly higher in Friday’s than in Monday’s samples, in exposed workers, 0.040 versus (vs.) 0.031 and non-exposed controls (0.030 vs. 0.024, p = 0.437). Environmental AFs contamination ranged from 7.2 to 125.4 µg/kg. The findings of this study reveal the presence of higher AFs concentration in exposed workers than in non-exposed controls, although these differences are to be considered consistent with random fluctuations. PMID:28338636

Preparation of Si nano-crystals with controlled oxidation state from SiO disproportionated by ZrO2 ball-milling

NASA Astrophysics Data System (ADS)

Okamoto, Yuji; Harada, Yoshitomo; Ohta, Narumi; Takada, Kazunori; Sumiya, Masatomo

2016-09-01

We demonstrate that a SiO disproportionation reaction can be achieved simply by high energy mechanochemical milling. The planetary ball-milling of ZrO2 for a few minutes generated Si nano-crystals. Milling conditions including rotation speed, ball number, milling time, and type of ball material were able to control the oxidation states of Si. The ball-milled SiO powder was tested as an anode of a lithium battery. ZrO2 contamination from the vial and balls was eliminated by dipping the ball-milled SiO powder in (NH4)HSO4 molten salt and heating for 5 min. The disproportionated SiO powder showed characteristics comparable to those of a powder prepared by a conventional heating process taking several hours.

An analysis of the lumber planning process: Part I

Treesearch

Peter Koch

1955-01-01

Report of study of the peripheral-milling process of planing lumber. Relationships were determined between cutterhead horsepower and various combinations of specimen, cutterhead, and feed factors. Power demand curves are interpreted by comparion with simultaneous one micro-second photos of chips. Secondary consideration is given to quality of surface obtained. The...

An analysis of the lumber planning process: Part II

Treesearch

Peter Koch

1956-01-01

This study is part II of an investigation pertaining to the peripheral-milling process of planing lumber. Some relationships were determined between cutterhead horsepower and various combinations of specimen, cutterhead, and feed factors. Power demand curves were interpreted through comparison with simultaneously taken one micro-second photos of the forming chips....

Effect of carbonaceous soil amendments on potential mobility of weak acid herbicides in soil

USDA-ARS?s Scientific Manuscript database

Use of carbonaceous amendments in soil has been proposed to decrease potential offsite transport of weak acid herbicides and metabolites by increasing their sorption to soil. The effects of organic olive mill waste, biochars from different feed stocks, and humic acid bound to clay on sorption of MCP...

Effect of feed source and pyrolysis conditions on sugarcane bagasse biochar

USDA-ARS?s Scientific Manuscript database

Processing of sugarcane in sugar mills yield ca. 30% bagasse, a fibrous waste material composed mostly of crushed cane stalks. While 80-90% of the bagasse used on site as fuel, the remaining portion can be converted into a value-added product. One such option is thermal conversion of bagasse into bi...

21 CFR 558.4 - Requirement of a medicated feed mill license.

Code of Federal Regulations, 2014 CFR

2014-04-01

.../ton 75-125. Oxytetracycline 90-120 20.0 g/lb (4.4%) 75-125/65-135. Penicillin 80-120 10.0 g/lb (2.2... g/lb (2.2%) 85-125/70-130. Penicillin 85-115 5.0 g/lb (1.1%) 85-125/70-130. Sulfamethazine 85-115 10...

Experimental Investigations to evaluate the effects of cutting parameters on cutting temperature and residual stresses during milling process of the AISI 1045

NASA Astrophysics Data System (ADS)

Abdelkrim, M.; Brabie, G.; Belloufi, A.; Catalin, T.; Chirita, B.

2017-08-01

Today major metal cutting companies in industrial countries, looking to gain time and reduce manufacturing costs while respecting the environment. There are many phenomena which affect the quality and production costs of the product, including cutting efforts, cutting temperature, residual stresses, etc. A better understanding of these phenomena will reduce production costs and maximize productivity. The aim of this work is to analyze the effect of machining conditions (cutting speed, feed speed and cutting depth) on cutting temperature and residual stresses, during the milling operations using the response surface method. A good accuracy between predicted and measured values of the cutting temperature was found, the cutting speed and the depth of cut are parameters whose effect is most sensitive to the residual stresses and the cutting temperature.However, little influence has been registered in the case of an increase of the feed rate. The percentage of error is 4.57%, indicating that the numerical approach can accurately predict the cutting temperature of the AISI 1045.

Feasibility of composting combinations of sewage sludge, olive mill waste and winery waste in a rotary drum reactor.

PubMed

Fernández, Francisco J; Sánchez-Arias, Virginia; Rodríguez, Lourdes; Villaseñor, José

2010-10-01

Representative samples of the following biowastes typically generated in Castilla La Mancha (Spain) were composted using a pilot-scale closed rotary drum composting reactor provided with adequate control systems: waste from the olive oil industry (olive mill waste; OMW), winery-distillery waste containing basically grape stalk and exhausted grape marc (WDW), and domestic sewage sludge. Composting these biowastes was only successful when using a bulking agent or if sufficient porosity was supported. OMW waste composting was not possible, probably because of its negligible porosity, which likely caused anaerobic conditions. WDW was successfully composted using a mixture of solid wastes generated from the same winery. SS was also successfully composted, although its higher heavy metal content was a limitation. Co-composting was an adequate strategy because the improved mixture characteristics helped to maintain optimal operating conditions. By co-composting, the duration of the thermophilic period increased, the final maturity level improved and OMW was successfully composted. Using the proposed reactor, composting could be accelerated compared to classical outdoor techniques, enabling easy control of the process. Moisture could be easily controlled by wet air feeding and leachate recirculation. Inline outlet gas analysis helped to control aerobic conditions without excessive aeration. The temperature reached high values in a few days, and sufficient thermal requirements for pathogen removal were met. The correct combination of biowastes along with appropriate reactor design would allow composting as a management option for such abundant biowastes in this part of Spain. (c) 2010 Elsevier Ltd. All rights reserved.

Comparison study on disturbance estimation techniques in precise slow motion control

NASA Astrophysics Data System (ADS)

Fan, S.; Nagamune, R.; Altintas, Y.; Fan, D.; Zhang, Z.

2010-08-01

Precise low speed motion control is important for the industrial applications of both micro-milling machine tool feed drives and electro-optical tracking servo systems. It calls for precise position and instantaneous velocity measurement and disturbance, which involves direct drive motor force ripple, guide way friction and cutting force etc., estimation. This paper presents a comparison study on dynamic response and noise rejection performance of three existing disturbance estimation techniques, including the time-delayed estimators, the state augmented Kalman Filters and the conventional disturbance observers. The design technique essentials of these three disturbance estimators are introduced. For designing time-delayed estimators, it is proposed to substitute Kalman Filter for Luenberger state observer to improve noise suppression performance. The results show that the noise rejection performances of the state augmented Kalman Filters and the time-delayed estimators are much better than the conventional disturbance observers. These two estimators can give not only the estimation of the disturbance but also the low noise level estimations of position and instantaneous velocity. The bandwidth of the state augmented Kalman Filters is wider than the time-delayed estimators. In addition, the state augmented Kalman Filters can give unbiased estimations of the slow varying disturbance and the instantaneous velocity, while the time-delayed estimators can not. The simulation and experiment conducted on X axis of a 2.5-axis prototype micro milling machine are provided.

Respirable Crystalline Silica Exposures During Asphalt Pavement Milling at Eleven Highway Construction Sites

PubMed Central

Hammond, Duane R.; Shulman, Stanley A.; Echt, Alan S.

2016-01-01

Asphalt pavement milling machines use a rotating cutter drum to remove the deteriorated road surface for recycling. The removal of the road surface has the potential to release respirable crystalline silica, to which workers can be exposed. This paper describes an evaluation of respirable crystalline silica exposures to the operator and ground worker from two different half-lane and larger asphalt pavement milling machines that had ventilation dust controls and water-sprays designed and installed by the manufacturers. Manufacturer A completed milling for eleven days at four highway construction sites in Wisconsin, while Manufacturer B completed milling for ten days at seven highway construction sites in Indiana. To evaluate the dust controls, full-shift personal breathing zone air samples were collected from an operator and ground worker during the course of normal employee work activities of asphalt pavement milling at eleven different sites. Forty-two personal breathing zone air samples were collected over 21 days (sampling on an operator and ground worker each day). All samples were below 50 µg/m3 for respirable crystalline silica, the National Institute for Occupational Safety and Health recommended exposure limit. The geometric mean personal breathing zone air sample was 6.2 µg/m3 for the operator and 6.1 µg/m3 for the ground worker for the Manufacturer A milling machine. The geometric mean personal breathing zone air sample was 4.2 µg/m3 for the operator and 9.0 µg/m3 for the ground worker for the Manufacturer B milling machine. In addition, upper 95% confidence limits for the mean exposure for each occupation were well below 50 µg/m3 for both studies. The silica content in the bulk asphalt material being milled ranged from 7% to 23% silica for roads milled by Manufacturer A and from 5% to 12% silica for roads milled by Manufacturer B. The results indicate that engineering controls consisting of ventilation controls in combination with water-sprays are capable of controlling occupational exposures to respirable crystalline silica generated by asphalt pavement milling machines on highway construction sites. PMID:26913983

Respirable crystalline silica exposures during asphalt pavement milling at eleven highway construction sites.

PubMed

Hammond, Duane R; Shulman, Stanley A; Echt, Alan S

2016-07-01

Asphalt pavement milling machines use a rotating cutter drum to remove the deteriorated road surface for recycling. The removal of the road surface has the potential to release respirable crystalline silica, to which workers can be exposed. This article describes an evaluation of respirable crystalline silica exposures to the operator and ground worker from two different half-lane and larger asphalt pavement milling machines that had ventilation dust controls and water-sprays designed and installed by the manufacturers. Manufacturer A completed milling for 11 days at 4 highway construction sites in Wisconsin, and Manufacturer B completed milling for 10 days at 7 highway construction sites in Indiana. To evaluate the dust controls, full-shift personal breathing zone air samples were collected from an operator and ground worker during the course of normal employee work activities of asphalt pavement milling at 11 different sites. Forty-two personal breathing zone air samples were collected over 21 days (sampling on an operator and ground worker each day). All samples were below 50 µg/m(3) for respirable crystalline silica, the National Institute for Occupational Safety and Health recommended exposure limit. The geometric mean personal breathing zone air sample was 6.2 µg/m(3) for the operator and 6.1 µg/m(3) for the ground worker for the Manufacturer A milling machine. The geometric mean personal breathing zone air sample was 4.2 µg/m(3) for the operator and 9.0 µg/m(3) for the ground worker for the Manufacturer B milling machine. In addition, upper 95% confidence limits for the mean exposure for each occupation were well below 50 µg/m(3) for both studies. The silica content in the bulk asphalt material being milled ranged from 7-23% silica for roads milled by Manufacturer A and from 5-12% silica for roads milled by Manufacturer B. The results indicate that engineering controls consisting of ventilation controls in combination with water-sprays are capable of controlling occupational exposures to respirable crystalline silica generated by asphalt pavement milling machines on highway construction sites.

Possibilities for preservation of coarse particles in pelleting process to improve feed quality characteristics.

PubMed

Vukmirović, D; Fišteš, A; Lević, J; Čolović, R; Rakić, D; Brlek, T; Banjac, V

2017-10-01

Poultry diets are mainly used in pelleted form because pellets have many advantages compared to mash feed. On the other hand, pelleting causes reduction of feed particle size. The aim of this research was to investigate the possibility of increasing the content of coarse particles in pellets, and, at the same time, to produce pellets with satisfactory quality. In this research, the three grinding treatments of corn were applied using hammer mill with three sieve openings diameter: 3 mm (HM-3), 6 mm (HM-6) and 9 mm (HM-9). These grinding treatments were combined in pelleting process with three gaps between rollers and the die of pellet press (roller-die gap, RDG) (0.30, 1.15 and 2.00 mm) and three moisture contents of the pelleted material (14.5, 16.0 and 17.5%). The increased coarseness of grinding by the hammer mill resulted in the increased amount of coarse particles in pellets, especially when the smallest RDG was applied (0.30 mm), but pellet quality was greatly reduced. Increasing of RDG improved the quality of pellets produced from coarsely ground corn, but reduced the content of coarse particles in pellets and increased specific energy consumption of the pellet press. Increasing the moisture content of material to be pelleted (MC) significantly reduced energy consumption of the pellet press, but there was no significant influence of MC on particle size after pelleting and on the pellet quality. The optimal values of the pelleting process parameters were determined using desirability function method. The results of optimization process showed that to achieve the highest possible quantity of coarse particles in the pellets, and to produce pellets of satisfactory quality, with the lowest possible energy consumption of the pellet press, the coarsest grinding on hammer mill (HM-9), the largest RDG (2 mm) and the highest MC (17.5%) should be applied. Journal of Animal Physiology and Animal Nutrition © 2016 Blackwell Verlag GmbH.

Diagnosis and Management of Rumen Acidosis and Bloat in Feedlots.

PubMed

Meyer, Nathan F; Bryant, Tony C

2017-11-01

Ruminal acidosis and ruminal bloat represent the most common digestive disorders in feedlot cattle. Ruminants are uniquely adapted to digest and metabolize a large range of feedstuffs. Although cattle have the ability to handle various feedstuffs, disorders associated with altered ruminal fermentation can occur. Proper ruminal microorganism adaptation and a consistent substrate (ration) help prevent digestive disorders. Feed bunk management, sufficient ration fiber, consistent feed milling, and appropriate response to abnormal weather are additional factors important in prevention of digestive disorders. When digestive disorders are suspected, timely diagnosis is imperative. Copyright © 2017 Elsevier Inc. All rights reserved.

Study design and preliminary data analysis for a streambank fencing project in the Mill Creek Basin, Pennsylvania

USGS Publications Warehouse

Galeone, Daniel G.; Koerkle, Edward H.

1996-01-01

The Pequea Creek and Mill Creek Basins within Lancaster and Chester Counties in Pennsylvania have been identified as areas needing control of nonpoint-source (NFS) pollution to improve water quality. The two basins are a total of approximately 200 square miles and are primarily underlain by carbonate bedrock. Land use is predominantly agriculture. The most common agricultural NFS pollution-control practices implemented in the Pequea Creek and Mill Creek Basins are barnyard-runoff control and Streambank fencing. To provide land managers information on the effectiveness of Streambank fencing in controlling NFS pollution, a study is being conducted in two small paired watersheds within the Mill Creek Basin.

A Virtual Sensor for Online Fault Detection of Multitooth-Tools

PubMed Central

Bustillo, Andres; Correa, Maritza; Reñones, Anibal

2011-01-01

The installation of suitable sensors close to the tool tip on milling centres is not possible in industrial environments. It is therefore necessary to design virtual sensors for these machines to perform online fault detection in many industrial tasks. This paper presents a virtual sensor for online fault detection of multitooth tools based on a Bayesian classifier. The device that performs this task applies mathematical models that function in conjunction with physical sensors. Only two experimental variables are collected from the milling centre that performs the machining operations: the electrical power consumption of the feed drive and the time required for machining each workpiece. The task of achieving reliable signals from a milling process is especially complex when multitooth tools are used, because each kind of cutting insert in the milling centre only works on each workpiece during a certain time window. Great effort has gone into designing a robust virtual sensor that can avoid re-calibration due to, e.g., maintenance operations. The virtual sensor developed as a result of this research is successfully validated under real conditions on a milling centre used for the mass production of automobile engine crankshafts. Recognition accuracy, calculated with a k-fold cross validation, had on average 0.957 of true positives and 0.986 of true negatives. Moreover, measured accuracy was 98%, which suggests that the virtual sensor correctly identifies new cases. PMID:22163766

A virtual sensor for online fault detection of multitooth-tools.

PubMed

Bustillo, Andres; Correa, Maritza; Reñones, Anibal

2011-01-01

The installation of suitable sensors close to the tool tip on milling centres is not possible in industrial environments. It is therefore necessary to design virtual sensors for these machines to perform online fault detection in many industrial tasks. This paper presents a virtual sensor for online fault detection of multitooth tools based on a bayesian classifier. The device that performs this task applies mathematical models that function in conjunction with physical sensors. Only two experimental variables are collected from the milling centre that performs the machining operations: the electrical power consumption of the feed drive and the time required for machining each workpiece. The task of achieving reliable signals from a milling process is especially complex when multitooth tools are used, because each kind of cutting insert in the milling centre only works on each workpiece during a certain time window. Great effort has gone into designing a robust virtual sensor that can avoid re-calibration due to, e.g., maintenance operations. The virtual sensor developed as a result of this research is successfully validated under real conditions on a milling centre used for the mass production of automobile engine crankshafts. Recognition accuracy, calculated with a k-fold cross validation, had on average 0.957 of true positives and 0.986 of true negatives. Moreover, measured accuracy was 98%, which suggests that the virtual sensor correctly identifies new cases.

78 FR 27859 - New Animal Drugs; Change of Sponsor's Name and Address; Change of Sponsor

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-13

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Parts 510 and 558... Purina Mills, Inc., to Purina Nutrition LLC, and a change of sponsor for a new animal drug application (NADA) from Land O'Lakes Purina Feed LLC to Purina Nutrition LLC. The regulations are also being amended...

Effect of Recycle Sludge on Anaerobic Digestion of Palm Oil Mill Effluent in A Thermophilic Continuous Digester

NASA Astrophysics Data System (ADS)

Irvan; Trisakti, B.; Tomiuchi, Y.; Harahap, U.; Daimon, H.

2017-06-01

The objective of this research is to maintain short retention time and high degradation of palm oil mill effluent (POME) to biogas by applying recycle sludge. Fresh POME from Rambutan Mill without further treatment was used as feed. Two lab-scale digesters supported from Metawater Co. Ltd. have been applied to treat POME at thermophilic (55°C) condition. Both digesters were operated under intermittent operation mode. Experiments were performed in two methods: with and without recycle sludge. Hydraulic retention time (HRT) of both methods was maintained at 6 days, while sludge retention time (SRT) was maintained at various days. The result showed that by extending SRT in return sludge process where 25% of digested slurry recycled to the digester, improvement of volatile solid (VS) decomposition was obtained around 84% at HRT of 6 days and SRT of 21 days. Then, chemical oxygen demand (COD) removal efficiency could be reached until 85% by using recycle sludge.

Investigation on Effect of Material Hardness in High Speed CNC End Milling Process.

PubMed

Dhandapani, N V; Thangarasu, V S; Sureshkannan, G

2015-01-01

This research paper analyzes the effects of material properties on surface roughness, material removal rate, and tool wear on high speed CNC end milling process with various ferrous and nonferrous materials. The challenge of material specific decision on the process parameters of spindle speed, feed rate, depth of cut, coolant flow rate, cutting tool material, and type of coating for the cutting tool for required quality and quantity of production is addressed. Generally, decision made by the operator on floor is based on suggested values of the tool manufacturer or by trial and error method. This paper describes effect of various parameters on the surface roughness characteristics of the precision machining part. The prediction method suggested is based on various experimental analysis of parameters in different compositions of input conditions which would benefit the industry on standardization of high speed CNC end milling processes. The results show a basis for selection of parameters to get better results of surface roughness values as predicted by the case study results.

Investigation on Effect of Material Hardness in High Speed CNC End Milling Process

PubMed Central

Dhandapani, N. V.; Thangarasu, V. S.; Sureshkannan, G.

2015-01-01

This research paper analyzes the effects of material properties on surface roughness, material removal rate, and tool wear on high speed CNC end milling process with various ferrous and nonferrous materials. The challenge of material specific decision on the process parameters of spindle speed, feed rate, depth of cut, coolant flow rate, cutting tool material, and type of coating for the cutting tool for required quality and quantity of production is addressed. Generally, decision made by the operator on floor is based on suggested values of the tool manufacturer or by trial and error method. This paper describes effect of various parameters on the surface roughness characteristics of the precision machining part. The prediction method suggested is based on various experimental analysis of parameters in different compositions of input conditions which would benefit the industry on standardization of high speed CNC end milling processes. The results show a basis for selection of parameters to get better results of surface roughness values as predicted by the case study results. PMID:26881267

An experimental study of flank wear in the end milling of AISI 316 stainless steel with coated carbide inserts

NASA Astrophysics Data System (ADS)

Odedeyi, P. B.; Abou-El-Hossein, K.; Liman, M.

2017-05-01

Stainless steel 316 is a difficult-to-machine iron-based alloys that contain minimum of about 12% of chromium commonly used in marine and aerospace industry. This paper presents an experimental study of the tool wear propagation variations in the end milling of stainless steel 316 with coated carbide inserts. The milling tests were conducted at three different cutting speeds while feed rate and depth of cut were at (0.02, 0.06 and 01) mm/rev and (1, 2 and 3) mm, respectively. The cutting tool used was TiAlN-PVD-multi-layered coated carbides. The effects of cutting speed, cutting tool coating top layer and workpiece material were investigated on the tool life. The results showed that cutting speed significantly affected the machined flank wears values. With increasing cutting speed, the flank wear values decreased. The experimental results showed that significant flank wear was the major and predominant failure mode affecting the tool life.

Extracts deriving from olive mill waste water and their effects on the liver of the goldfish Carassius auratus fed with hypercholesterolemic diet.

PubMed

Alesci, Alessio; Cicero, Nicola; Salvo, Andrea; Palombieri, Deborah; Zaccone, Daniele; Dugo, Giacomo; Bruno, Maurizio; Vadalà, Rossella; Lauriano, Eugenia Rita; Pergolizzi, Simona

2014-01-01

The present research aims to evaluate the beneficial effects of polyphenols derived from waste water from a olive mill, obtained by non-plastic molecular imprinting device, in a hypercholesterolemic diet on Carassius auratus, commonly known as goldfish that was selected as experimental model. The study was conducted with morphological and histochemical analyses and also the data were supported by immunohistochemical analysis. Results show the beneficial activity of polyphenols with a reduction of the damage in the steatotic group, confirming that they may be suggested in the treatment of diseases by lipid accumulation, and used as any addition in feed for farmed fish, in order to improve the organoleptic and nutritional quality. The beneficial effects of waste oil extract should be suggested in the contexts of research programmes focused on the products to the health system. Furthermore, the olive mill waste water polyphenols free can be used as natural fertilizers.

Fabrication of micro-lens array on convex surface by meaning of micro-milling

NASA Astrophysics Data System (ADS)

Zhang, Peng; Du, Yunlong; Wang, Bo; Shan, Debin

2014-08-01

In order to develop the application of the micro-milling technology, and to fabricate ultra-precision optical surface with complex microstructure, in this paper, the primary experimental research on micro-milling complex microstructure array is carried out. A complex microstructure array surface with vary parameters is designed, and the mathematic model of the surface is set up and simulated. For the fabrication of the designed microstructure array surface, a micro three-axis ultra-precision milling machine tool is developed, aerostatic guideway drove directly by linear motor is adopted in order to guarantee the enough stiffness of the machine, and novel numerical control strategy with linear encoders of 5nm resolution used as the feedback of the control system is employed to ensure the extremely high motion control accuracy. With the help of CAD/CAM technology, convex micro lens array on convex spherical surface with different scales on material of polyvinyl chloride (PVC) and pure copper is fabricated using micro tungsten carbide ball end milling tool based on the ultra-precision micro-milling machine. Excellent nanometer-level micro-movement performance of the axis is proved by motion control experiment. The fabrication is nearly as the same as the design, the characteristic scale of the microstructure is less than 200μm and the accuracy is better than 1μm. It prove that ultra-precision micro-milling technology based on micro ultra-precision machine tool is a suitable and optional method for micro manufacture of microstructure array surface on different kinds of materials, and with the development of micro milling cutter, ultraprecision micro-milling complex microstructure surface will be achieved in future.

Uranium and radium concentrations in plants growing on uranium mill tailings in South Dakota

Treesearch

Mark A. Rumble; Ardell J. Bjugstad

1986-01-01

Vegetation and soil samples were collected from a uranium mill tailings site and control sites in South Dakota. Uranium concentrations in soils from the mill tailings averaged 13.3 [micro]g g-1 compared to 5.1 [micro]g g-1 in soils from control sites. 226Ra concentrations in soils averaged 111.0 pCi g...

Surface Finish and Residual Stresses Induced by Orthogonal Dry Machining of AA7075-T651

PubMed Central

Jomaa, Walid; Songmene, Victor; Bocher, Philippe

2014-01-01

The surface finish was extensively studied in usual machining processes (turning, milling, and drilling). For these processes, the surface finish is strongly influenced by the cutting feed and the tool nose radius. However, a basic understanding of tool/surface finish interaction and residual stress generation has been lacking. This paper aims to investigate the surface finish and residual stresses under the orthogonal cutting since it can provide this information by avoiding the effect of the tool nose radius. The orthogonal machining of AA7075-T651 alloy through a series of cutting experiments was performed under dry conditions. Surface finish was studied using height and amplitude distribution roughness parameters. SEM and EDS were used to analyze surface damage and built-up edge (BUE) formation. An analysis of the surface topography showed that the surface roughness was sensitive to changes in cutting parameters. It was found that the formation of BUE and the interaction between the tool edge and the iron-rich intermetallic particles play a determinant role in controlling the surface finish during dry orthogonal machining of the AA7075-T651 alloy. Hoop stress was predominantly compressive on the surface and tended to be tensile with increased cutting speed. The reverse occurred for the surface axial stress. The smaller the cutting feed, the greater is the effect of cutting speed on both axial and hoop stresses. By controlling the cutting speed and feed, it is possible to generate a benchmark residual stress state and good surface finish using dry machining. PMID:28788534

Modeling of Surface Geometric Structure State After Integratedformed Milling and Finish Burnishing

NASA Astrophysics Data System (ADS)

Berczyński, Stefan; Grochała, Daniel; Grządziel, Zenon

2017-06-01

The article deals with computer-based modeling of burnishing a surface previously milled with a spherical cutter. This method of milling leaves traces, mainly asperities caused by the cutting crossfeed and cutter diameter. The burnishing process - surface plastic treatment - is accompanied by phenomena that take place right in the burnishing ball-milled surface contact zone. The authors present the method for preparing a finite element model and the methodology of tests for the assessment of height parameters of a surface geometrical structure (SGS). In the physical model the workpieces had a cuboidal shape and these dimensions: (width × height × length) 2×1×4.5 mm. As in the process of burnishing a cuboidal workpiece is affected by plastic deformations, the nonlinearities of the milled item were taken into account. The physical model of the process assumed that the burnishing ball would be rolled perpendicularly to milling cutter linear traces. The model tests included the application of three different burnishing forces: 250 N, 500 N and 1000 N. The process modeling featured the contact and pressing of a ball into the workpiece surface till the desired force was attained, then the burnishing ball was rolled along the surface section of 2 mm, and the burnishing force was gradually reduced till the ball left the contact zone. While rolling, the burnishing ball turned by a 23° angle. The cumulative diagrams depict plastic deformations of the modeled surfaces after milling and burnishing with defined force values. The roughness of idealized milled surface was calculated for the physical model under consideration, i.e. in an elementary section between profile peaks spaced at intervals of crossfeed passes, where the milling feed fwm = 0.5 mm. Also, asperities after burnishing were calculated for the same section. The differences of the obtained values fall below 20% of mean values recorded during empirical experiments. The adopted simplification in after-milling SGS modeling enables substantial acceleration of the computing process. There is a visible reduction of the Ra parameter value for milled and burnished surfaces as the burnishing force rises. The tests determined an optimal burnishing force at a level of 500 N (lowest Ra = 0.24 μm). Further increase in the value of burnishing force turned out not to affect the surface roughness, which is consistent with the results obtained from experimental studies.

75 FR 26794 - International Paper Company Franklin Pulp & Paper Mill Including On-Site Leased Workers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-12

... Company Franklin Pulp & Paper Mill Including On-Site Leased Workers From Railserve, Franklin, VA; Amended... workers of International Paper Company, Franklin Pulp & Paper Mill, Franklin, Virginia. The notice was... Pulp & Paper Mill. The Department has determined that these workers were sufficiently under the control...

11. VIEW OF HORIZONTAL MIXER (GedgeGray Co., Lockland, Ohio), LOCATED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. VIEW OF HORIZONTAL MIXER (Gedge-Gray Co., Lockland, Ohio), LOCATED IN THE BASEMENT, MIXED ANIMAL FEED TO ORDER. THE WATER-POWERED MIXER WAS SUPERSEDED BY TWO ELECTRIC-POWERED VERTICAL MIXERS, ADDED IN THE 1940S. Photographer: Louise Taft Cawood, July 1986 - Alexander's Grist Mill, Lock 37 on Ohio & Erie Canal, South of Cleveland, Valley View, Cuyahoga County, OH

JPRS Report, China.

DTIC Science & Technology

1989-10-17

fermented livestock feeds; and processing chopped coarse fodders for agri- culture. JPRS-CAR-89-103 17 October 1989 ECONOMIC 43 4. Administration and...distribution of leftovers from brewing and fermentation industries and from non- staple food factories that use grain as raw materials. Residues from...bean product manufacturing plants and flour mills, and sediments from soy sauce, vinegar plants, distilleries and breweries should be managed and

Effectiveness of pulsed light treatment for degradation and detoxification of aflatoxin B1 and B2 in rough rice and rice bran

USDA-ARS?s Scientific Manuscript database

Aflatoxins primarily accumulate in the hull and bran layers of rough rice making these by-products of rice milling unsuitable for animal feed or human consumption. Contaminated rough rice is also a potential source of aflatoxin exposure to workers handling the grain during post-harvest storage and p...

Large-scale alcohol production from corn, grain sorghum, and crop residues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turhollow, A.F. Jr.

1982-01-01

The potential impacts that large-scale alcohol production from corn, grain sorghum, and crop residues may have on US agriculture in the year 2000 are investigated. A one-land-group interregional linear-programming model is used. The objective function is to minimize the cost of production in the agricultural sector, given specified crop demands and constrained resources. The impacts that levels of alcohol production, ranging from zero to 12 billion gallons, have at two projected levels of crop demands, two grain-to-alcohol conversion and two milling methods, wet and dry, rates are considered. The impacts that large-scale fuel alcohol production has on US agriculture aremore » small. The major impacts that occur are the substitution of milling by-products, DDG, gluten feed, and gluten meal, for soybean meal in livestock feed rations. Production of 12 billion gallons of alcohol is estimated to be equivalent to an 18 percent increase in crop exports. Improving the grain-to-alcohol conversion rate from 2.6 to 3.0 gallons per bushels reduces the overall cost of agricultural production by $989 billion when 12 billion gallons of alcohol are produced.« less

Evaluation of flotation for purification of pyrite for use in thermal batteries

NASA Astrophysics Data System (ADS)

Guidotti, R. A.; Reinhardt, F. W.

1992-07-01

The purification of pyrite (FeS2) used in Li-alloy/FeS2 thermal batteries by the physical process of flotation was evaluated for reduction of the quartz impurity. The process was compared to the standard process of leaching with concentrated hydrofluoric acid. Flotation was an attractive alternative because it avoided many of the safety and environmental concerns posed by the use of concentrated HF. The effects of particle size and initial purity of the pyrite feed material upon the final purity and yield of the product concentrate were examined for batch sizes from 3.5 to 921 kg. Feed materials as coarse as 8 mm and as fine as -325 mesh were treated; the coarse pyrite was ground wet in a rod mill or dry in a vibratory mill to -230 mesh prior to flotation. Both the HF-leached and the flotation-treated pyrite were leached with HCI (1:1 v/v) to remove acid-soluble impurities. The flotation-purified pyrite concentrates were formulated into catholytes; their electrochemical performance was evaluated in both single cells and 5-cell batteries for comparison to data generated under the same discharge conditions for catholytes formulated with HF/HCI purified pyrite.

Experimental and Mathematical Modeling for Prediction of Tool Wear on the Machining of Aluminium 6061 Alloy by High Speed Steel Tools

NASA Astrophysics Data System (ADS)

Okokpujie, Imhade Princess; Ikumapayi, Omolayo M.; Okonkwo, Ugochukwu C.; Salawu, Enesi Y.; Afolalu, Sunday A.; Dirisu, Joseph O.; Nwoke, Obinna N.; Ajayi, Oluseyi O.

2017-12-01

In recent machining operation, tool life is one of the most demanding tasks in production process, especially in the automotive industry. The aim of this paper is to study tool wear on HSS in end milling of aluminium 6061 alloy. The experiments were carried out to investigate tool wear with the machined parameters and to developed mathematical model using response surface methodology. The various machining parameters selected for the experiment are spindle speed (N), feed rate (f), axial depth of cut (a) and radial depth of cut (r). The experiment was designed using central composite design (CCD) in which 31 samples were run on SIEG 3/10/0010 CNC end milling machine. After each experiment the cutting tool was measured using scanning electron microscope (SEM). The obtained optimum machining parameter combination are spindle speed of 2500 rpm, feed rate of 200 mm/min, axial depth of cut of 20 mm, and radial depth of cut 1.0mm was found out to achieved the minimum tool wear as 0.213 mm. The mathematical model developed predicted the tool wear with 99.7% which is within the acceptable accuracy range for tool wear prediction.

17. Woodworking Mill (basement): view looking north showing Ames Iron ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. Woodworking Mill (basement): view looking north showing Ames Iron Works steam boiler; note turbine control handle in middle right of photo - Ben Thresher's Mill, State Aid No. 1, Barnet, Caledonia County, VT

An investigation into the design and performance of an automatic shape control system for a Sendzimir cold rolling mill

NASA Astrophysics Data System (ADS)

Dutton, Kenneth

Shape (or flatness) control for rolled steel strip is becoming increasingly important as customer requirements become more stringent. Automatic shape control is now more or less mandatory on all new four-high cold mills, but no comprehensive scheme yet exists on a Sendzimir mill. This is due to the complexity of the control system design on such a mill, where many more degrees of freedom for control exist than is the case with the four-high mills.The objective of the current work is to develop, from first principles, such a system; including automatic control of the As-U-Roll and first intermediate roll actuators in response to the measured strip shape. This thesis concerns itself primarily with the As-U-Roll control system. The material presented is extremely wide-ranging. Areas covered include the development of original static and dynamic mathematical models of the mill systems, and testing of the plant by data-logging to tune these models. A basic control system philosophy proposed by other workers is modified and developed to suit the practical system requirements and the data provided by the models. The control strategy is tested by comprehensive multivariable simulation studies. Finally, details are given of the practical problems faced when installing the system on the plant. These include problems of manual control inter-action bumpless transfer and integral desaturation.At the time of presentation of the thesis, system commissioning is still in progress and production results are therefore not yet available. Nevertheless, the simulation studies predict a successful outcome, although performance is expected to be limited until the first intermediate roll actuators are eventually included in the scheme also.

Twin-belt continuous caster with containment and cooling of the exiting cast product for enabling high-speed casting of molten-center product

DOEpatents

Dykes, Charles D.; Daniel, Sabah S.; Wood, J. F. Barry

1990-02-20

In continuously casting molten metal into cast product by a twin-belt machine, it is desirable to achieve dramatic increases in speed (linear feet per minute) at which cast product exits the machine, particularly in installations where steel cast product is intended to feed a downstream regular rolling mill (as distinct from a planetary mill) operating in tandem with the twin-belt caster. Such high-speed casting produces product with a relatively thin shell and molten interior, and the shell tends to bulge outwardly due to metallostatic head pressure of the molten center. A number of cooperative features enable high-speed, twin-belt casting: (1) Each casting belt is slidably supported adjacent to the caster exit pulley for bulge control and enhanced cooling of cast product. (2) Lateral skew steering of each belt provides an effective increase in moving mold length plus a continuity of heat transfer not obtained with prior art belt steering apparatus. (3) The exiting slab is contained and supported downstream from the casting machine to prevent bulging of the shell of the cast product, and (4) spray cooling is incorporated in the exit containment apparatus for secondary cooling of cast product.

Design, experimentation, and modeling of a novel continuous biodrying process

NASA Astrophysics Data System (ADS)

Navaee-Ardeh, Shahram

Massive production of sludge in the pulp and paper industry has made the effective sludge management increasingly a critical issue for the industry due to high landfill and transportation costs, and complex regulatory frameworks for options such as sludge landspreading and composting. Sludge dewatering challenges are exacerbated at many mills due to improved in-plant fiber recovery coupled with increased production of secondary sludge, leading to a mixed sludge with a high proportion of biological matter which is difficult to dewater. In this thesis, a novel continuous biodrying reactor was designed and developed for drying pulp and paper mixed sludge to economic dry solids level so that the dried sludge can be economically and safely combusted in a biomass boiler for energy recovery. In all experimental runs the economic dry solids level was achieved, proving the process successful. In the biodrying process, in addition to the forced aeration, the drying rates are enhanced by biological heat generated through the microbial activity of mesophilic and thermophilic microorganisms naturally present in the porous matrix of mixed sludge. This makes the biodrying process more attractive compared to the conventional drying techniques because the reactor is a self-heating process. The reactor is divided into four nominal compartments and the mixed sludge dries as it moves downward in the reactor. The residence times were 4-8 days, which are 2-3 times shorter than the residence times achieved in a batch biodrying reactor previously studied by our research group for mixed sludge drying. A process variable analysis was performed to determine the key variable(s) in the continuous biodrying reactor. Several variables were investigated, namely: type of biomass feed, pH of biomass, nutrition level (C/N ratio), residence times, recycle ratio of biodried sludge, and outlet relative humidity profile along the reactor height. The key variables that were identified in the continuous biodrying reactor were the type of biomass feed and the outlet relative humidity profiles. The biomass feed is mill specific and since one mill was studied for this study, the nutrition level of the biomass feed was found adequate for the microbial activity, and hence the type of biomass is a fixed parameter. The influence of outlet relative humidity profile was investigated on the overall performance and the complexity index of the continuous biodrying reactor. The best biodrying efficiency was achieved at an outlet relative humidity profile which controls the removal of unbound water at the wet-bulb temperature in the 1st and 2nd compartments of the reactor, and the removal of bound water at the dry-bulb temperature in the 3rd and 4th compartments. Through a systematic modeling approach, a 2-D model was developed to describe the transport phenomena in the continuous biodrying reactor. The results of the 2-D model were in satisfactory agreement with the experimental data. It was found that about 30% w/w of the total water removal (drying rate) takes place in the 1st and 2nd compartments mainly under a convection dominated mechanism, whereas about 70% w/w of the total water removal takes place in the 3rd and 4th compartments where a bioheat-diffusion dominated mechanism controls the transport phenomena. The 2-D model was found to be an appropriate tool for the estimation of the total water removal rate (drying rate) in the continuous biodrying reactor when compared to the 1-D model. A dimensionless analysis was performed on the 2-D model and established the preliminary criteria for the scale-up of the continuous biodrying process. Finally, a techno-economic assessment of the continuous biodrying process revealed that there is great potential for the implementation of the biodrying process in Canadian pulp and paper mills. The techno-economic results were compared to the other competitive existing drying technologies. It was proven that the continuous biodrying process results in significant economic benefits and has great potential to address the current industrial problems associated with sludge management.

A Low Noise, Microprocessor-Controlled, Internally Digitizing Rotating-Vane Electric Field Mill for Airborne Platforms

NASA Technical Reports Server (NTRS)

Bateman, M. G.; Stewart, M. F.; Blakeslee, R. J.; Podgorny, s. J.; Christian, H. J.; Mach, D. M.; Bailey, J. C.; Daskar, D.

2006-01-01

This paper reports on a new generation of aircraft-based rotating-vane style electric field mills designed and built at NASA's Marshall Spaceflight Center. The mills have individual microprocessors that digitize the electric field signal at the mill and respond to commands from the data system computer. The mills are very sensitive (1 V/m per bit), have a wide dynamic range (115 dB), and are very low noise (+/-1 LSB). Mounted on an aircraft, these mills can measure fields from +/-1 V/m to +/-500 kV/m. Once-per-second commanding from the data collection computer to each mill allows for precise timing and synchronization. The mills can also be commanded to execute a self-calibration in flight, which is done periodically to monitor the status and health of each mill.

Evaluation of the Mating Competitiveness of the Adult Oriental Fruit Fly Reared as Larvae in Liquid vs. Those Raised on Standard Wheat-based Diets

USDA-ARS?s Scientific Manuscript database

Three strains (standard lab, DTWP pupal color sexing strain and wild strain) of adult oriental fruit flies, which were reared as larvae on a liquid diet, mill feed diet (Tanaka’s diet), or natural host fruit diet, were evaluated for mating competitiveness in both indoor and outdoor Boller’s mating c...

92. VIEW OF PRECIPITATION AREA FROM SOUTHWEST. VACUUM CLARIFIER TANK ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

92. VIEW OF PRECIPITATION AREA FROM SOUTHWEST. VACUUM CLARIFIER TANK No. 1 AT LOWER LEFT, UNDER LAUNDER FEED TO GOLD TANK No. 2, AND VACUUM CLARIFIER TANK No. 2, AT MIDRIGHT. VACUUM RECEIVER TANK ON UPPER LEFT. PIPE TO TOP CENTER OF TANK TAKES OUTFLOW FROM CLARIFIER LEAVES. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Use of a complete starter feed in grain adaptation programs for feedlot cattle.

PubMed

Schneider, C J; Nuttelman, B L; Shreck, A L; Burken, D B; Griffin, W A; Gramkow, J L; Stock, R A; Klopfenstein, T J; Erickson, G E

2017-08-01

Four experiments evaluated the use of a complete starter feed (RAMP; Cargill Corn Milling, Blair, NE) for grain adaptation. In Exp. 1, 229 yearling steers (397 ± 28.4 kg BW) were used to compare a traditional adaptation program (CON) with adapting cattle with RAMP in either a 1- (RAMP-1RS) or 2- (RAMP-2RS) ration system. From d 23 to slaughter, cattle were fed a common finishing diet. In Exp. 2, 390 yearling steers (341 ± 14 kg BW) were used to compare accelerated grain adaptation programs with RAMP with 2 control treatments where RAMP was blended with a finishing diet containing either 25 (CON25) or 47.5% (CON47) Sweet Bran (Cargill Corn Milling) in 4 steps fed over 24 d to adapt cattle. Rapid adaptation treatments involved feeding RAMP for 10 d followed by a blend of RAMP and a 47% Sweet Bran finishing diet to transition cattle with 3 blends fed for 1 d each (3-1d), 2 blends fed for 2 d each (2-2d), or 1 blend fed for 4 d (1-4d). From d 29 to slaughter, all cattle were fed a common finishing diet. In Exp. 3, 300 steer calves (292 ± 21 kg BW) were used to compare the CON47 and 1-4d adaptation programs with directly transitioning cattle from RAMP, which involved feeding RAMP for 10 d and then switching directly to F1 on d 11 (1-STEP). From d 29 until slaughter, F2 was fed to all cattle. In Exp. 4, 7 ruminally fistulated steers (482 ± 49 kg BW) were used in a 35-d trial to compare the CON47 and 1-STEP adaptation programs. Ruminal pH and intake data from the first 6 d of F1and first 6 d of F2 were used to compare adaptation systems. Adaptation with RAMP-1RS and RAMP-2RS increased ( < 0.01) G:F compared with cattle adapted using CON in Exp. 1. Feeding RAMP-1RS increased ADG ( = 0.03) compared with CON. Intakes were similar ( = 0.39) among treatments. Daily gain, DMI, G:F, and carcass traits were similar ( > 0.11) among treatments in Exp. 2. Daily gain, DMI, and G:F were not different ( > 0.20) among treatments on d 39 or over the entire feeding period in Exp. 3. When F1 or F2 was being fed, DMI was similar ( ≥ 0.40) for CON47 and 1-STEP in Exp. 4. When F1 or F2 was being fed, 1-STEP cattle had lower average ruminal pH ( ≤ 0.03) and greater time below a pH of 5.3 ( ≤ 0.03). Using RAMP for grain adaptation improved performance compared with traditional adaptation. Rapid adaptation with RAMP decreased pH, but no performance differences were observed between long and rapid RAMP adaptation programs. Therefore, cattle started on RAMP do not require extensive adaptation before feeding a finishing diet with Sweet Bran.

Estimation of tool wear length in finish milling using a fuzzy inference algorithm

NASA Astrophysics Data System (ADS)

Ko, Tae Jo; Cho, Dong Woo

1993-10-01

The geometric accuracy and surface roughness are mainly affected by the flank wear at the minor cutting edge in finish machining. A fuzzy estimator obtained by a fuzzy inference algorithm with a max-min composition rule to evaluate the minor flank wear length in finish milling is introduced. The features sensitive to minor flank wear are extracted from the dispersion analysis of a time series AR model of the feed directional acceleration of the spindle housing. Linguistic rules for fuzzy estimation are constructed using these features, and then fuzzy inferences are carried out with test data sets under various cutting conditions. The proposed system turns out to be effective for estimating minor flank wear length, and its mean error is less than 12%.

Mycotoxin Contamination in the EU Feed Supply Chain: A Focus on Cereal Byproducts.

PubMed

Pinotti, Luciano; Ottoboni, Matteo; Giromini, Carlotta; Dell'Orto, Vittorio; Cheli, Federica

2016-02-15

Mycotoxins represent a risk to the feed supply chain with an impact on economies and international trade. A high percentage of feed samples have been reported to be contaminated with more than one mycotoxin. In most cases, the concentrations were low enough to ensure compliance with the European Union (EU) guidance values or maximum admitted levels. However, mycotoxin co-contamination might still exert adverse effects on animals due to additive/synergistic interactions. Studies on the fate of mycotoxins during cereal processing, such as milling, production of ethanol fuels, and beer brewing, have shown that mycotoxins are concentrated into fractions that are commonly used as animal feed. Published data show a high variability in mycotoxin repartitioning, mainly due to the type of mycotoxins, the level and extent of fungal contamination, and a failure to understand the complexity of food processing technologies. Precise knowledge of mycotoxin repartitioning during technological processes is critical and may provide a sound technical basis for feed managers to conform to legislation requirements and reduce the risk of severe adverse market and trade repercussions. Regular, economical and straightforward feed testing is critical to reach a quick and accurate diagnosis of feed quality. The use of rapid methods represents a future challenge.

Mycotoxin Contamination in the EU Feed Supply Chain: A Focus on Cereal Byproducts

PubMed Central

Pinotti, Luciano; Ottoboni, Matteo; Giromini, Carlotta; Dell’Orto, Vittorio; Cheli, Federica

2016-01-01

Mycotoxins represent a risk to the feed supply chain with an impact on economies and international trade. A high percentage of feed samples have been reported to be contaminated with more than one mycotoxin. In most cases, the concentrations were low enough to ensure compliance with the European Union (EU) guidance values or maximum admitted levels. However, mycotoxin co-contamination might still exert adverse effects on animals due to additive/synergistic interactions. Studies on the fate of mycotoxins during cereal processing, such as milling, production of ethanol fuels, and beer brewing, have shown that mycotoxins are concentrated into fractions that are commonly used as animal feed. Published data show a high variability in mycotoxin repartitioning, mainly due to the type of mycotoxins, the level and extent of fungal contamination, and a failure to understand the complexity of food processing technologies. Precise knowledge of mycotoxin repartitioning during technological processes is critical and may provide a sound technical basis for feed managers to conform to legislation requirements and reduce the risk of severe adverse market and trade repercussions. Regular, economical and straightforward feed testing is critical to reach a quick and accurate diagnosis of feed quality. The use of rapid methods represents a future challenge. PMID:26891326

Numerical simulation study on rolling-chemical milling process of aluminum-lithium alloy skin panel

NASA Astrophysics Data System (ADS)

Huang, Z. B.; Sun, Z. G.; Sun, X. F.; Li, X. Q.

2017-09-01

Single curvature parts such as aircraft fuselage skin panels are usually manufactured by rolling-chemical milling process, which is usually faced with the problem of geometric accuracy caused by springback. In most cases, the methods of manual adjustment and multiple roll bending are used to control or eliminate the springback. However, these methods can cause the increase of product cost and cycle, and lead to material performance degradation. Therefore, it is of significance to precisely control the springback of rolling-chemical milling process. In this paper, using the method of experiment and numerical simulation on rolling-chemical milling process, the simulation model for rolling-chemical milling process of 2060-T8 aluminum-lithium alloy skin was established and testified by the comparison between numerical simulation and experiment results for the validity. Then, based on the numerical simulation model, the relative technological parameters which influence on the curvature of the skin panel were analyzed. Finally, the prediction of springback and the compensation can be realized by controlling the process parameters.

75 FR 55274 - Change of Address for Region 5 State and Local Agencies; Technical Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-10

... Health District, Air Pollution Control, 33 Mill Street, Painesville, OH 44077. (xiv) Mahoning and...; Director, Canton City Health Department, Air Pollution Control Division, 420 Market Avenue North, Canton.... (xiii) Geauga and Lake Counties; Lake County General Health District, Air Pollution Control, 33 Mill...

Understanding dental CAD/CAM for restorations - dental milling machines from a mechanical engineering viewpoint. Part A: chairside milling machines.

PubMed

Lebon, Nicolas; Tapie, Laurent; Duret, Francois; Attal, Jean-Pierre

2016-01-01

The dental milling machine is an important device in the dental CAD/CAM chain. Nowadays, dental numerical controlled (NC) milling machines are available for dental surgeries (chairside solution). This article provides a mechanical engineering approach to NC milling machines to help dentists understand the involvement of technology in digital dentistry practice. First, some technical concepts and definitions associated with NC milling machines are described from a mechanical engineering viewpoint. The technical and economic criteria of four chairside dental NC milling machines that are available on the market are then described. The technical criteria are focused on the capacities of the embedded technologies of these milling machines to mill both prosthetic materials and types of shape restorations. The economic criteria are focused on investment costs and interoperability with third-party software. The clinical relevance of the technology is assessed in terms of the accuracy and integrity of the restoration.

Aerobic dynamic feeding as a strategy for in situ accumulation of polyhydroxyalkanoate in aerobic granules.

PubMed

Gobi, K; Vadivelu, V M

2014-06-01

Aerobic dynamic feeding (ADF) strategy was applied in sequencing batch reactor (SBR) to accumulate polyhydroxyalkanoate (PHA) in aerobic granules. The aerobic granules were able to remove 90% of the COD from palm oil mill effluent (POME). The volatile fatty acids (VFAs) in the POME are the sole source of the PHA accumulation. In this work, 100% removal of propionic and butyric acids in the POME were observed. The highest amount of PHA produced in aerobic granules was 0.6833mgPHA/mgbiomass. The PHA formed was identified as a P (hydroxybutyrate-co-hydroxyvalerate) P (HB-co-HV). Copyright © 2014 Elsevier Ltd. All rights reserved.

10 CFR 150.15a - Continued Commission authority pertaining to byproduct material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... consistent with the provisions of the Uranium Mill Tailings Radiation Control Act of 1978, provided that the... Mill Tailings Radiation Control Act of 1978; and (6) The authority to enter into arrangements as may be...

Determination of regulatory ionophore coccidiostat residues in feedstuffs at carry-over levels by liquid chromatography-mass spectrometry

PubMed Central

Stramenga, Arianna; Colagrande, Maria Novella; Campana, Guido; Scortichini, Giampiero; Migliorati, Giacomo; Compagnone, Dario

2017-01-01

In this study samples of feedstuffs were collected from different feed mills and animal farms located in central Italy and analyzed for ionophore coccidiostat residues at carry-over levels by liquid chromatography-mass spectrometry. Since unavoidable cross-contamination of feedstuffs may occur during their production as well as distribution and storage, the collection of samples covered all these different stages. Residues of lasalocid, monensin, salinomycin and maduramicin were detected in 32.4% of samples, both at production and storage level. The maximum content for unavoidable carry-over set by Regulation (EU) No 574/2011 was exceeded in 11.3% of samples. The variability of the results highlighted the different approach of each investigated feed business operator to avoid any cross-contamination in non-target feed. The method developed in this study can be able to detect ionophore coccidiostats at low concentrations consequent to carry-over. PMID:28792977

Prevalence of respiratory symptoms and disorders among rice mill workers in India.

PubMed

Ghosh, Tirthankar; Gangopadhyay, Somnath; Das, Banibrata

2014-05-01

Lung function tests have become an integral part of assessment of pulmonary disease. Diseases of the respiratory system induced by occupational dusts are influenced by the duration of exposure. The aim of the study is to investigate the impairment of lung function and prevalence of respiratory symptoms among the rice mill workers. A total of 120 rice mill workers from three districts of Karnataka were included in this study. Fifty urban dwellers from the same socio-economic level were selected as controls. The study included clinical examination, assessment of respiratory symptoms, pulmonary function test, measurement of peak expiratory flow rate, absolute eosinophil count, ESR estimation, total IgE estimation and radiographic test. The present study has shown that the rice mill workers complained of several types of respiratory disorders like phlegm (40.8 %), dyspnea (44.2 %), chest tightness (26.7 %), cough (21.7 %), and nose irritation (27.5 %). Rice mill workers exposed to dust presented significantly (p < 0.05) lower levels of FVC (3.44 ± 0.11), FEV1 (2.73 ± 0.15) and PEFR (304.95 ± 28.79) than the controls. The rice mill workers are having significantly higher absolute eosinophil counts, total IgE and ESR than control groups. The hematological findings suggest that the harmful effects may be linked to both non-specific irritation and allergic responses to rice husk dust among rice mill workers. Dust exposure in the working environment affects the lung function values and increased the respiratory symptoms among the rice mill workers.

Effects of pelleting conditioner retention time on nursery pig growth performance.

PubMed

Lewis, L L; Stark, C R; Fahrenholz, A C; Goncalves, M A D; DeRouchey, J M; Jones, C K

2015-03-01

A total of 180 nursery pigs (PIC 327 × 1050; initially 12.6 kg) were used in an 18-d study to determine the effects of pellet mill conditioning parameters and feed form on pig performance. All diets were similar, and different feed processing parameters were used to create experimental treatments. Factors considered were conditioning time (15, 30, or 60 s) and feed form (mash or pelleted). To remove the confounding factor of feed form, pelleted samples were reground to a similar particle size as the mash diet. Treatments included: 1) mash diet without thermal processing (negative control), 2) pelleted diet conditioned for 30 s (positive control), 3) pelleted diet conditioned for 15 s and reground, 4) pelleted diet conditioned for 30 s and reground, and 5) pelleted diet conditioned for 60 s and reground. Pigs were weaned and fed a common acclimation diet for 21 d before the start of the experiment. Growth and feed disappearance were then measured for 18 d. All diets had similar levels of percentage total starch, but thermally processed diets had a 1.67 to 1.87-fold increase in percentage gelatinized starch compared to the mash diet. Average daily gain and G:F did not differ between treatments overall, but pigs fed the positive control pelleted diet had decreased ADFI ( < 0.05) compared to pigs fed all other diets. Preplanned contrasts revealed that pigs fed mash diets tended to have greater ADG ( < 0.10) compared to those fed pelleted and reground diets. This suggests that processing may have had a negative influence on feed utilization, which is further supported by the finding that pigs fed mash diets tended to have greater ADG ( < 0.10) compared to those fed diets that were thermally processed, regardless of regrinding. Considering these results, it was not surprising that pigs fed mash diets had greater ADG and ADFI ( < 0.05) than those fed pelleted diets. When directly comparing diets conditioned at 60 rpm, fed either as whole pellets or reground to mash consistency, pigs fed pelleted diets had improved G:F ( < 0.05) due to lower ADFI ( < 0.05) but similar ADG. The expected improvement in G:F from pelleting (6.8%) was observed but lost when diets were reground to near original mash particle size. This may indicate that diet form from the actual pelleting process impacts G:F more than conditioner retention time.

40 CFR 192.00 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.00 Applicability. This... sites under section 108 of the Uranium Mill Tailings Radiation Control Act of 1978 (henceforth...

40 CFR 192.00 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.00 Applicability. This... sites under section 108 of the Uranium Mill Tailings Radiation Control Act of 1978 (henceforth...

40 CFR 192.00 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.00 Applicability. This... sites under section 108 of the Uranium Mill Tailings Radiation Control Act of 1978 (henceforth...

40 CFR 192.00 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.00 Applicability. This... sites under section 108 of the Uranium Mill Tailings Radiation Control Act of 1978 (henceforth...

38. VIEW OF CRUSHER ROOM FROM NORTH. THE CRUSHER IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. VIEW OF CRUSHER ROOM FROM NORTH. THE CRUSHER IS MISSING, BUT THREE GRIZZLIES AND THE FEED GATE FROM THE SOUTH ORE BIN ARE STILL VISIBLE. PULLEY AT BOTTOM OF THE VIEW IS THE BEGINNING OF THE 24 INCH BELT CONVEYOR. NOTE SOUTH BIN DIAGONAL SHEATHING MATCHES THAT IN VIEW SD-2-3. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Higher accumulation of proteinase inhibitors in flowers than leaves and fruits as a possible basis for differential feeding preference of Helicoverpa armigera on tomato (Lycopersicon esculentum Mill, Cv. Dhanashree).

PubMed

Damle, Mrunal S; Giri, Ashok P; Sainani, Mohini N; Gupta, Vidya S

2005-11-01

Tomato (Lycopersicon esculentum, Mill; cultivar- Dhanashree) proteinase inhibitors (PIs) were tested for their trypsin inhibitory (TI) and Helicoverpa armigera gut proteinases inhibitory (HGPI) activity in different organs of the tomato plants. Analysis of TI and HGPI distribution in various parts of the plant showed that flowers accumulated about 300 and 1000 times higher levels of TI while 700 and 400 times higher levels of HGPI as compared to those in leaves and fruits, respectively. Field observation that H. armigera larvae infest leaves and fruits but not the flowers could be at least partially attributed to the protective role-played by the higher levels of PIs in the flower tissue. Tomato PIs inhibited about 50-80% HGP activity of H. armigera larvae feeding on various host plants including tomato, of larvae exposed to non-host plant PIs and of various larval instars. Tomato PIs were found to be highly stable to insect proteinases wherein incubation of inhibitor with HGP even for 3h at optimum conditions did not affect inhibitory activity. Bioassay using H. armigera larvae fed on artificial diet containing tomato PIs revealed adverse effect on larval growth, pupae development, adult formation and fecundity.

The use of cutting temperature to evaluate the machinability of titanium alloys.

PubMed

Kikuchi, Masafumi

2009-02-01

This study investigated the machinability of titanium, two commercial titanium alloys (Ti-6Al-4V and Ti-6Al-7Nb) and free-cutting brass using the cutting temperature. The cutting temperature was estimated by measuring the thermal electromotive force of the tool-workpiece thermocouple during cutting. The thermoelectric power of each metal relative to the tool had previously been determined. The metals were slotted using a milling machine and carbide square end mills under four cutting conditions. The cutting temperatures of Ti-6Al-4V and Ti-6Al-7Nb were significantly higher than that of the titanium, while that of the free-cutting brass was lower. This result coincided with the relationship of the magnitude of the cutting forces measured in a previous study. For each metal, the cutting temperature became higher when the depth of cut or the cutting speed and feed increased. The increase in the cutting speed and feed was more influential on the value than the increase in the depth of cut when two cutting conditions with the same removal rates were compared. The results demonstrated that cutting temperature measurement can be utilized to develop a new material for dental CAD/CAM applications and to optimize the cutting conditions.

Environmental noise levels affect the activity budget of the Florida manatee

NASA Astrophysics Data System (ADS)

Miksis-Olds, Jennifer L.; Donaghay, Percy L.; Miller, James H.; Tyack, Peter L.

2005-09-01

Manatees inhabit coastal bays, lagoons, and estuaries because they are dependent on the aquatic vegetation that grows in shallow waters. Food requirements force manatees to occupy the same areas in which human activities are the greatest. Noise produced from human activities has the potential to affect these animals by eliciting responses ranging from mild behavioral changes to extreme aversion. This study quantifies the behavioral responses of manatees to both changing levels of ambient noise and transient noise sources. Results indicate that elevated environmental noise levels do affect the overall activity budget of this species. The proportion of time manatees spend feeding, milling, and traveling in critical habitats changed as a function of noise level. More time was spent in the directed, goal-oriented behaviors of feeding and traveling, while less time was spent milling when noise levels were highest. The animals also responded to the transient noise of approaching vessels with changes in behavioral state and movements out of the geographical area. This suggests that manatees detect and respond to changes in environmental noise levels. Whether these changes legally constitute harassment and produce biologically significant effects need to be addressed with hypothesis-driven experiments and long-term monitoring. [For Animal Bioacoustics Best Student Paper Award.

A Novel Hybrid Error Criterion-Based Active Control Method for on-Line Milling Vibration Suppression with Piezoelectric Actuators and Sensors

PubMed Central

Zhang, Xingwu; Wang, Chenxi; Gao, Robert X.; Yan, Ruqiang; Chen, Xuefeng; Wang, Shibin

2016-01-01

Milling vibration is one of the most serious factors affecting machining quality and precision. In this paper a novel hybrid error criterion-based frequency-domain LMS active control method is constructed and used for vibration suppression of milling processes by piezoelectric actuators and sensors, in which only one Fast Fourier Transform (FFT) is used and no Inverse Fast Fourier Transform (IFFT) is involved. The correction formulas are derived by a steepest descent procedure and the control parameters are analyzed and optimized. Then, a novel hybrid error criterion is constructed to improve the adaptability, reliability and anti-interference ability of the constructed control algorithm. Finally, based on piezoelectric actuators and acceleration sensors, a simulation of a spindle and a milling process experiment are presented to verify the proposed method. Besides, a protection program is added in the control flow to enhance the reliability of the control method in applications. The simulation and experiment results indicate that the proposed method is an effective and reliable way for on-line vibration suppression, and the machining quality can be obviously improved. PMID:26751448

Crystallization of high-strength nano-scale leucite glass-ceramics.

PubMed

Theocharopoulos, A; Chen, X; Wilson, R M; Hill, R; Cattell, M J

2013-11-01

Fine-grained, high strength, translucent leucite dental glass-ceramics are synthesized via controlled crystallization of finely milled glass powders. The objectives of this study were to utilize high speed planetary milling of an aluminosilicate glass for controlled surface crystallization of nano-scale leucite glass-ceramics and to test the biaxial flexural strength. An aluminosilicate glass was synthesized, attritor or planetary milled and heat-treated. Glasses and glass-ceramics were characterized using particle size analysis, X-ray diffraction and scanning electron microscopy. Experimental (fine and nanoscale) and commercial (Ceramco-3, IPS Empress Esthetic) leucite glass-ceramics were tested using the biaxial flexural strength (BFS) test. Gaussian and Weibull statistics were applied. Experimental planetary milled glass-ceramics showed an increased leucite crystal number and nano-scale median crystal sizes (0.048-0.055 μm(2)) as a result of glass particle size reduction and heat treatments. Experimental materials had significantly (p<0.05) higher mean BFS and characteristic strength values than the commercial materials. Attritor milled and planetary milled (2h) materials showed no significant (p>0.05) strength difference. All other groups' mean BFS and characteristic strengths were found to be significantly different (p<0.05) to each other. The mean (SD) MPa strengths measured were: Attritor milled: 252.4 (38.7), Planetary milled: 225.4 (41.8) [4h milling] 255.0 (35.0) [2h milling], Ceramco-3: 75.7 (6.8) and IPS Empress: 165.5 (30.6). Planetary milling enabled synthesis of nano-scale leucite glass-ceramics with high flexural strength. These materials may help to reduce problems associated with brittle fracture of all-ceramic restorations and give reduced enamel wear. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

John Stuart Mill on Freedom, Education, and Social Reform.

ERIC Educational Resources Information Center

Carbone, Peter F.

1983-01-01

Examines the social philosophy of John Stuart Mill, emphasizing his views on freedom, education, and social reform. Considers Mill's individualism and reformism, the conflict between freedom and control that characterizes his work, and the importance of freedom and education. Suggests caution in drawing educational implications from his work. (DAB)

Operating System For Numerically Controlled Milling Machine

NASA Technical Reports Server (NTRS)

Ray, R. B.

1992-01-01

OPMILL program is operating system for Kearney and Trecker milling machine providing fast easy way to program manufacture of machine parts with IBM-compatible personal computer. Gives machinist "equation plotter" feature, which plots equations that define movements and converts equations to milling-machine-controlling program moving cutter along defined path. System includes tool-manager software handling up to 25 tools and automatically adjusts to account for each tool. Developed on IBM PS/2 computer running DOS 3.3 with 1 MB of random-access memory.

A comparative study of cultural methods for the detection of Salmonella in feed and feed ingredients

PubMed Central

Koyuncu, Sevinc; Haggblom, Per

2009-01-01

Background Animal feed as a source of infection to food producing animals is much debated. In order to increase our present knowledge about possible feed transmission it is important to know that the present isolation methods for Salmonella are reliable also for feed materials. In a comparative study the ability of the standard method used for isolation of Salmonella in feed in the Nordic countries, the NMKL71 method (Nordic Committee on Food Analysis) was compared to the Modified Semisolid Rappaport Vassiliadis method (MSRV) and the international standard method (EN ISO 6579:2002). Five different feed materials were investigated, namely wheat grain, soybean meal, rape seed meal, palm kernel meal, pellets of pig feed and also scrapings from a feed mill elevator. Four different levels of the Salmonella serotypes S. Typhimurium, S. Cubana and S. Yoruba were added to each feed material, respectively. For all methods pre-enrichment in Buffered Peptone Water (BPW) were carried out followed by enrichments in the different selective media and finally plating on selective agar media. Results The results obtained with all three methods showed no differences in detection levels, with an accuracy and sensitivity of 65% and 56%, respectively. However, Müller-Kauffmann tetrathionate-novobiocin broth (MKTTn), performed less well due to many false-negative results on Brilliant Green agar (BGA) plates. Compared to other feed materials palm kernel meal showed a higher detection level with all serotypes and methods tested. Conclusion The results of this study showed that the accuracy, sensitivity and specificity of the investigated cultural methods were equivalent. However, the detection levels for different feed and feed ingredients varied considerably. PMID:19192298

Decoupling the Arrhenius equation via mechanochemistry.

PubMed

Andersen, Joel M; Mack, James

2017-08-01

Mechanochemistry continues to reveal new possibilities in chemistry including the opportunity for "greening" reactions. Nevertheless, a clear understanding of the energetic transformations within mechanochemical systems remains elusive. We employed a uniquely modified ball mill and strategically chosen Diels-Alder reactions to evaluate the role of several ball-milling variables. This revealed three different energetic regions that we believe are defining characteristics of most, if not all, mechanochemical reactors. Relative to the locations of a given ball mill's regions, activation energy determines whether a reaction is energetically easy (Region I), challenging (Region II), or unreasonable (Region III) in a given timeframe. It is in Region II, that great sensitivity to mechanochemical conditions such as vial material and oscillation frequency emerge. Our unique modifications granted control of reaction vessel temperature, which in turn allowed control of the locations of Regions I, II, and III for our mill. Taken together, these results suggest envisioning vibratory mills (and likely other mechanochemical methodologies) as molecular-collision facilitating devices that act upon molecules occupying a thermally-derived energy distribution. This unifies ball-milling energetics with solution-reaction energetics via a common tie to the Arrhenius equation, but gives mechanochemistry the unique opportunity to influence either half of the equation. In light of this, we discuss a strategy for translating solvent-based reaction conditions to ball milling conditions. Lastly, we posit that the extra control via frequency factor grants mechanochemistry the potential for greater selectivity than conventional solution reactions.

Utilization of lime-dried sludge for eco-cement clinker production: effects of different feeding points.

PubMed

Cao, Haihua; Liu, Wei; Xu, Jingcheng; Liu, Jia; Huang, Juwen; Huang, Xiangfeng; Li, Guangming

2018-02-01

Co-processing lime-dried sludge (LDS) in cement kilns is an appropriate technique to solve the problem of LDS disposal and promote the sustainable development for cement industry. However, there were limited studies that investigated the effects of feeding points on product quality and cement kiln emissions. In this study, simulated experiments were conducted by dividing the feeding points into high-temperature zones (HTZs) and raw mill (RM). Cement quality and major cement kiln emission characteristics were comprehensively investigated. The results showed that in terms of burnability, compressive strength and microstructure, the optimum co-processing amount of LDS were 9 wt% when feeding at RM, while 6% when feeding at HTZs. Meanwhile, the organic emissions of RM samples were mainly low environmental risk compounds of amides and nitrogenous heterocyclic compounds. Inorganic gaseous pollutions of NO X and SO 2 , respectively, were 8.11 mg/g DS and 12.89 mg/g DS, compared with 7.61 mg/g DS and 4.44 mg/g DS for HTZs. However, all the cement kiln emissions concentration were still much lower than standard requirements. Overall, RM had a bigger LDS co-processing capacity and higher, but acceptable, cement kiln emissions. Feeding LDS via RM could dispose larger amounts of sludge and provide more alternative materials for cement manufacturing.

Bay Mills' Bold Approach

ERIC Educational Resources Information Center

Freedman, Eric

2011-01-01

It's a long, long way from Bay Mills Community College, near the shores of frigid Lake Superior, to Detroit. But distance, time and demographics aside, the school and the city are united by Bay Mills' status as the nation's only tribally controlled college that authorizes quasi-public schools, known officially as public school academies. And it's…

The synergistic effects of combining the high energy mechanical milling and wet milling on Si negative electrode materials for lithium ion battery

NASA Astrophysics Data System (ADS)

Hou, Shang-Chieh; Su, Yuh-Fan; Chang, Chia-Chin; Hu, Chih-Wei; Chen, Tsan-Yao; Yang, Shun-Min; Huang, Jow-Lay

2017-05-01

The submicro-sized and nanostructured Si aggregated powder is prepared by combinational routes of high energy mechanical milling (HEMM) and wet milling. Milled Si powder is investigated by particle size analyzer, SEM, TEM, XPS and XRD as well as the control ones. Its electrode is also investigated by in situ XRD and electrochemical performance. Morphology reveals that combining the high energy mechanical milling and wet milling not only fracture primary Si particles but also form submicro-sized Si aggregates constructed by amorphous and nanocrystalline phases. Moreover, XPS shows that wet milling in ethanol trigger Sisbnd Osbnd CH2CH3 bonding on Si surface might enhance the SEI formation. In situ XRD analysis shows negative electrode made of submicro-sized Si aggregated powder can effectively suppress formation of crystalline Li15Si4 during lithiation and delithiation due to amorphous and nanocrystalline construction. Thus, the submicro-sized Si powder with synergistic effects combining the high energy mechanical milling and wet milling in ethanol as negative electrode performs better capacity retention.

Chlorpyrifos residual behaviors in field crops and transfers during duck pellet feed processing.

PubMed

Li, Rui; Wei, Wei; He, Liang; Hao, Lili; Ji, Xiaofeng; Zhou, Yu; Wang, Qiang

2014-10-22

Chlorpyrifos is a widely used organophosphorus pesticide in agricultural crops (including food) and animal feeds in China, resulting in heavy contamination. Many studies have focused on the food-processing effects on chlorpyrifos removal, but sufficient information is not observed for feed-processing steps. Here, chlorpyrifos residual behaviors in field crops and its transfers in duck pellet feed-processing steps were evaluated. In field trials, the highest residues for rice grain, shelled corn, and soybean seed were 12.0, 0.605, and 0.220 mg/kg, respectively. Residues of all rice grain and about half of shelled corn exceeded the maximum residue limits (MRLs) of China, and five soybean seeds exceeded the MRL of China. Chlorpyrifos residue was reduced 38.2% in brown rice after the raw rice grain was hulled. The residue in bran increased 71.2% after milling from brown rice. During the squashing step, the residue reduced 73.8% in soybean meal. The residues reduced significantly (23.7-36.8%) during the process of granulating for rice, maize, and soybean products. Comparatively, the grinding process showed only limited influence on chlorpyrifos removal (<10%). The residues of duck pellet feeds produced from highly contaminated raw materials of this study were 1.01 mg/kg (maize-soybean feed) and 3.20 mg/kg (rice-soybean feed), which were much higher than the generally accepted value (>0.1 mg/kg) for animal feeding. Chlorpyrifos residues were removed significantly by processing steps of pellet feeds, but the residue of raw materials was the determining factor for the safety of duck feeding.

Identification of milling and baking quality QTL in multiple soft wheat mapping populations

USDA-ARS?s Scientific Manuscript database

Wheat derived food products require a range of characteristics. Identification and understanding of the genetic components controlling end-use quality of wheat is important for crop improvement. We assessed the underlying genetics controlling specific milling and baking quality parameters of soft wh...

45. VIEW OF UPPER LEVEL CRUSHER ADDITION FROM CRUSHED OXIDIZED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. VIEW OF UPPER LEVEL CRUSHER ADDITION FROM CRUSHED OXIDIZED ORE BIN. 18 INCH BELT CONVEYOR BIN FEED, LOWER CENTER, WITH STEPHENS-ADAMSON 25 TON/HR ELEVATOR SPLIT DISCHARGE (OXIDIZED/UNOXIDIZED) IN CENTER. CRUDE ORE BINS AND MACHINE SHOP BEYOND. NOTE TOP OF CRUSHED OXIDIZED ORE BIN IS BELOW TOP OF CRUDE ORE BINS. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Critical Technology Assessment of Five Axis Simultaneous Control Machine Tools

DTIC Science & Technology

2009-07-01

assessment, BIS specifically examined: • The application of Export Control Classification Numbers ( ECCN ) 2B001.b.2 and 2B001.c.2 controls and related...availability of certain five axis simultaneous control mills, mill/turns, and machining centers controlled by ECCN 2B001.b.2 (but not grinders controlled by... ECCN 2B001.c.2) exists to China and Taiwan, which both have an indigenous capability to produce five axis simultaneous control machine tools with

Collaborative study on the effect of grinding on the detection of bones from processed animal proteins in feed by light microscopy.

PubMed

Veys, Pascal; Planchon, Viviane; Colbert, Ruairi; Cruz, Clara; Frick, Geneviève; Ioannou, Ioannis; Marchis, Daniela; Nordkvist, Erik; Paradies-Severin, Inge; Pohto, Arja; Weiss, Roland; Baeten, Vincent; Berben, Gilbert

2017-08-01

Bone fragments are essential structures for the detection of processed animal proteins (PAPs) in feed by light microscopy for official controls according to Annex VI of European Union Regulation EC/152/2009. The preparation of samples submitted for analysis requires a grinding step to make them suitable for microscopic slide preparation and observation. However, there are no technical guidelines set down for this step despite the fact that it can lead to an increase in bone numbers due to fragmentation. This was demonstrated by an in-house study carried out by the Irish National Reference Laboratory (NRL) for animal protein detection. The present collaborative study investigated the possible effects of three different grinding conditions on the final result for a feed adulterated with 0.05 and 0.01% (w/w) of PAP. The microscopic analysis either combined or not with an Alizarin Red staining was carried out by 10 different laboratories. The results demonstrated that although a large variation in the numbers of bone fragments was noted, five of the six different grinding/staining combinations applied at two levels of PAP adulteration did not significantly (at p = 0.05) differ from one another. The only exception occurred when grinding the feed containing 0.05% of PAP with a rotor mill equipped with a 0.5-mm sieve and combined with a staining which resulted in a greater number of bone fragments by forced fragmentation. Overall, the impact of the grinding/staining combinations on the final results was shown to be negligible when considering the regulatory limit of detection (LOD) requirement for the method and the current rules of implementation of the light microscopic method. From a total of 180 analyses carried out on the feed matrix containing 0.05% of PAP no false-negative result was observed, and at a level of 0.01% PAP only 10 false-negative results occurred.

Toolpath Strategy and Optimum Combination of Machining Parameter during Pocket Mill Process of Plastic Mold Steels Material

NASA Astrophysics Data System (ADS)

Wibowo, Y. T.; Baskoro, S. Y.; Manurung, V. A. T.

2018-02-01

Plastic based products spread all over the world in many aspects of life. The ability to substitute other materials is getting stronger and wider. The use of plastic materials increases and become unavoidable. Plastic based mass production requires injection process as well Mold. The milling process of plastic mold steel material was done using HSS End Mill cutting tool that is widely used in a small and medium enterprise for the reason of its ability to be re sharpened and relatively inexpensive. Study on the effect of the geometry tool states that it has an important effect on the quality improvement. Cutting speed, feed rate, depth of cut and radii are input parameters beside to the tool path strategy. This paper aims to investigate input parameter and cutting tools behaviors within some different tool path strategy. For the reason of experiments efficiency Taguchi method and ANOVA were used. Response studied is surface roughness and cutting behaviors. By achieving the expected quality, no more additional process is required. Finally, the optimal combination of machining parameters will deliver the expected roughness and of course totally reduced cutting time. However actually, SMEs do not optimally use this data for cost reduction.

Surface Roughness Optimization of Polyamide-6/Nanoclay Nanocomposites Using Artificial Neural Network: Genetic Algorithm Approach

PubMed Central

Moghri, Mehdi; Omidi, Mostafa; Farahnakian, Masoud

2014-01-01

During the past decade, polymer nanocomposites attracted considerable investment in research and development worldwide. One of the key factors that affect the quality of polymer nanocomposite products in machining is surface roughness. To obtain high quality products and reduce machining costs it is very important to determine the optimal machining conditions so as to achieve enhanced machining performance. The objective of this paper is to develop a predictive model using a combined design of experiments and artificial intelligence approach for optimization of surface roughness in milling of polyamide-6 (PA-6) nanocomposites. A surface roughness predictive model was developed in terms of milling parameters (spindle speed and feed rate) and nanoclay (NC) content using artificial neural network (ANN). As the present study deals with relatively small number of data obtained from full factorial design, application of genetic algorithm (GA) for ANN training is thought to be an appropriate approach for the purpose of developing accurate and robust ANN model. In the optimization phase, a GA is considered in conjunction with the explicit nonlinear function derived from the ANN to determine the optimal milling parameters for minimization of surface roughness for each PA-6 nanocomposite. PMID:24578636

High productivity mould robotic milling in Al-5083

NASA Astrophysics Data System (ADS)

Urresti, Iker; Arrazola, Pedro Jose; Ørskov, Klaus Bonde; Pelegay, Jose Angel

2018-05-01

Industrial serial robots were usually limited to welding, handling or spray painting operations until very recent years. However, some industries have already realized about their important capabilities in terms of flexibility, working space, adaptability and cost. Hence, currently they are seriously being considered to carry out certain metal machining tasks. Therefore, robot based machining is presented as a cost-saving and flexible manufacturing alternative compared to conventional CNC machines especially for roughing or even pre-roughing of large parts. Nevertheless, there are still some drawbacks usually referred as low rigidity, accuracy and repeatability. Thus, the process productivity is usually sacrificed getting low Material Removal Rates (MRR), and consequently not being competitive. Nevertheless, in this paper different techniques to obtain increased productivity are presented, though an appropriate selection of cutting strategies and parameters that are essential for it. During this research some rough milling tests in Al-5083 are presented where High Feed Milling (HFM) is implemented as productive cutting strategy and the experimental modal analysis named Tap-testing is used for the suitable choice of cutting conditions. Competitive productivity rates are experienced while process stability is checked through the cutting forces measurements in order to prove the effectiveness of the experimental modal analysis for robotic machining.

DOE/NETL's phase II mercury control technology field testing program: preliminary economic analysis of activated carbon injection.

PubMed

Jones, Andrew P; Hoffmann, Jeffrey W; Smith, Dennis N; Feeley, Thomas J; Murphy, James T

2007-02-15

Based on results of field testing conducted by the U.S. Department of Energy's National Energy Technology Laboratory (DOE/NETL), this article provides preliminary costs for mercury control via conventional activated carbon injection (ACI), brominated ACI, and conventional ACI coupled with the application of a sorbent enhancement additive (SEA) to coal prior to combustion. The economic analyses are reported on a plant-specific basis in terms of the cost required to achieve low (50%), mid (70%), and high (90%) levels of mercury removal "above and beyond" the baseline mercury removal achieved by existing emission control equipment. In other words, the levels of mercury control are directly attributable to ACI. Mercury control costs via ACI have been amortized on a current dollar basis. Using a 20-year book life, levelized costs for the incremental increase in cost of electricity (COE), expressed in mills per kilowatt-hour (mills/kWh), and the incremental cost of mercury control, expressed in dollars per pound of mercury removed ($/lb Hg removed), have been calculated for each level of ACI mercury control. For this analysis, the increase in COE varied from 0.14 mills/kWh to 3.92 mills/kWh. Meanwhile, the incremental cost of mercury control ranged from $3810/lb Hg removed to $166000/lb Hg removed.

Impact of industrial effluents on the biochemical composition of fresh water fish Labeo rohita.

PubMed

Muley, D V; Karanjkar, D M; Maske, S V

2007-04-01

In acute toxicity (96 hr) experiment the fingerlings of freshwater fish Labeo rohita was exposed to tannery, electroplating and textile mill effluents. The LC0 and LC50 concentrations were 15% and 20% for tannery effluents, 3% and 6% for electroplating effluents and 18% and 22% for textile mill effluents respectively. It was found that, electroplating effluent was more toxic than tannery and textile mill wastes. After acute toxicity experiments for different industrial effluents, various tissues viz. gill, liver, muscle and kidney were obtained separately from control, LC0 and LC50 groups. These tissues were used for biochemical estimations. The glycogen content in all the tissues decreased considerably upon acute toxicity of three industrial effluents except muscle in LC50 group of tannery effluent and kidney in LC50 group of textile mill effluent, when compared to control group. The total protein content decreased in all tissues in three effluents except gills in LC50 group of tannery effluent, kidney in LC50 group of electroplating effluent and kidney in LC0 group of textile mill effluent. In general total lipid content decreased in all tissues after acute exposure when compared to control group. The results obtained in the present study showed that, the industrial effluents from tannery, electroplating and textile mills caused marked depletion in biochemical composition in various tissues of the fish Labeo rohita after acute exposure.

Zeolite/magnetite composites as catalysts on the Synthesis of Methyl Esters (MES) from cooking oil

NASA Astrophysics Data System (ADS)

Sriatun; Darmawan, Adi; Sriyanti; Cahyani, Wuri; Widyandari, Hendri

2018-05-01

The using of zeolite/magnetite composite as a catalyst for the synthesis of methyl esters (MES) of cooking oil has been performed. In this study the natural magnetite was extracted from the iron sand of Semarang marina beach and milled by high energy Milling (HEM) with ball: magnetite ratio: 1:1. The composites prepared from natural zeolite and natural magnetite with zeolite: magnetite ratio 1:1; 2:1; 3:1 and 4:1. Preparation of methyl ester was catalyzed by composite of zeolite/magnetite through transeserification reaction, it was studied on variation of catalyst concentration (w/v) 1%, 3%, 5% and 10% to feed volume. The reaction product are mixture of methyl Oleic (MES), methyl Palmitic (MES) and methyl Stearic (MES). Character product of this research include density, viscosity, acid number and iodine number has fulfilled to SNI standard 7182: 2015.

Vermiremediation of dyeing sludge from textile mill with the help of exotic earthworm Eisenia fetida Savigny.

PubMed

Bhat, Sartaj Ahmad; Singh, Jaswinder; Vig, Adarsh Pal

2013-09-01

The aim of present study was for the vermiremediation of dyeing sludge from textile mill into nutrient-rich vermicompost using earthworm Eisenia fetida. The dyeing sludge was mixed with cattle dung in different ratios, i.e., 0:100 (D0), 25:75 (D25), 50:50 (D50), 75:25 (D75), and 100:0 (D100) with earthworms, and 0:100 (S0), 25:75 (S25), 50:50 (S50), 75:25 (S75), and 100:0 (S100) without earthworms. Minimum mortality and maximum population build-up were observed in a 25:75 mixture. Nitrogen, phosphorus, sodium, and pH increased from the initial to the final products with earthworms, while electrical conductivity, C/N ratio, organic carbon, and potassium declined in all the feed mixtures. Vermicomposting with E. fetida was better for composting to change this sludge into nutrient-rich manure.

Annual monitoring report for the Gunnison, Colorado, wetlands mitigation plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-10-01

The US Department of Energy (DOE) administers the Uranium Mill Tailings Remedial Action (UMTRA) Project to clean up uranium mill tailings and other surface contamination at 24 abandoned uranium mill sites in 10 states. One of these abandoned mill sites is near the town of Gunnison, Colorado; surface remediation and the environmental impacts of remedial action are described in the Gunnison environmental assessment (EA) (DOE, 1992). Remedial action resulted in the elimination of 4.3 acres (ac) 1.7 hectares (ha) of wetlands and mitigation of this loss of wetlands is being accomplished through the enhance of 18.4 ac (7.5 ha) ofmore » riparian plant communities in six spring feed areas on Bureau of Land Management (BLM) land. The description of the impacted and mitigation wetlands is provided in the Mitigation and Monitoring Plan for Impacted Wetlands at the Gunnison UMTRA Project Site, Gunnison, Colorado (DOE, 1994), which is attached to the US Army corps of Engineers (USACE) Section 404 Permit. As part of the wetlands mitigation plan, the six mitigation wetlands were fenced in the fall of 1993 to exclude livestock grazing. Baseline of grazed conditions of the wetlands vegetation was determined during the summer of 1993 (DOE, 1994). A 5-year monitoring program of these six sites has been implemented to document the response of vegetation and wildlife to the exclusion of livestock. This annual monitoring report provides the results of the first year of the 5-year monitoring period.« less

Investigations on Surface Milling of Hardened AISI 4140 Steel with Pulse Jet MQL Applicator

NASA Astrophysics Data System (ADS)

Bashir, Mahmood Al; Mia, Mozammel; Dhar, Nikhil Ranjan

2018-06-01

In this article, an experimental investigation was performed in milling hardened AISI 4140 steel of hardness 40 HRC. The machining was performed in both dry and minimal quantity lubricant (MQL) conditions, as part of neat machining, to make a strong comparison of the undertaken machining environments. The MQL was impinged int the form of pulse jet, by using the specially developed pulse-jet-attachment, to ensure that the cutting fluid can be applied in different timed pulses and quantities at critical zones. The tool wear, cutting force and surface roughness were taken as the quality responses while cutting speed, table feed rate and flow rate of the pulse were considered as influential factors. The depth of cut was kept constant at 1.50 mm because of its less significant effects and the straight oil was adopted as cutting fluid in pulse-jet-MQL. The effects of different factors, on the quality responses, are analyzed using ANOVA. It is observed that MQL applicator system exhibits overall better performance when compared to dry milling by reducing surface roughness, cutting force and prolonging tool life but a flow rate of 150 ml/h has tremendous effects on the responses. This investigation and afterward results are expected to aid the industrial practitioner and researcher to adopt the pulse-MQL in high speed milling to prolong tool life, reduce tool wear, diminish cutting force generation and promote better surface finish.

Investigations on Surface Milling of Hardened AISI 4140 Steel with Pulse Jet MQL Applicator

NASA Astrophysics Data System (ADS)

Bashir, Mahmood Al; Mia, Mozammel; Dhar, Nikhil Ranjan

2016-06-01

In this article, an experimental investigation was performed in milling hardened AISI 4140 steel of hardness 40 HRC. The machining was performed in both dry and minimal quantity lubricant (MQL) conditions, as part of neat machining, to make a strong comparison of the undertaken machining environments. The MQL was impinged int the form of pulse jet, by using the specially developed pulse-jet-attachment, to ensure that the cutting fluid can be applied in different timed pulses and quantities at critical zones. The tool wear, cutting force and surface roughness were taken as the quality responses while cutting speed, table feed rate and flow rate of the pulse were considered as influential factors. The depth of cut was kept constant at 1.50 mm because of its less significant effects and the straight oil was adopted as cutting fluid in pulse-jet-MQL. The effects of different factors, on the quality responses, are analyzed using ANOVA. It is observed that MQL applicator system exhibits overall better performance when compared to dry milling by reducing surface roughness, cutting force and prolonging tool life but a flow rate of 150 ml/h has tremendous effects on the responses. This investigation and afterward results are expected to aid the industrial practitioner and researcher to adopt the pulse-MQL in high speed milling to prolong tool life, reduce tool wear, diminish cutting force generation and promote better surface finish.

Quality control troubleshooting tools for the mill floor

Treesearch

John Dramm

2000-01-01

Statistical Process Control (SPC) provides effective tools for improving process quality in the forest products industry resulting in reduced costs and improved productivity. Implementing SPC helps identify and locate problems that occur in wood products manufacturing. SPC tools achieve their real value when applied on the mill floor for monitoring and troubleshooting...

Field Operations and Enforcement Manual for Air Pollution Control. Volume III: Inspection Procedures for Specific Industries.

ERIC Educational Resources Information Center

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume III, explains in detail the following: inspection procedures for specific sources, kraft pulp mills, animal rendering, steel mill furnaces, coking operations, petroleum refineries, chemical plants, non-ferrous smelting and refining, foundries, cement plants, aluminum…

21 CFR 558.4 - Requirement of a medicated feed mill license.

Code of Federal Regulations, 2013 CFR

2013-04-01

.../ton 75-125. Oxytetracycline 90-120 20.0 g/lb (4.4%) 75-125/65-135. Penicillin 80-120 10.0 g/lb (2.2... 85-115 10.0 g/lb (2.2%) 85-125/70-130. Penicillin 85-115 5.0 g/lb (1.1%) 85-125/70-130.../lb (2.2%) 70-130. Penicillin 80-120 5.0 g/lb (1.1%) 70-130. Thiabendazole 94-106 45.4 g/lb (10.0%) >7...

21 CFR 558.4 - Requirement of a medicated feed mill license.

Code of Federal Regulations, 2011 CFR

2011-04-01

.../ton 75-125. Oxytetracycline 90-120 20.0 g/lb (4.4%) 75-125/65-135. Penicillin 80-120 10.0 g/lb (2.2... 10.0 g/lb (2.2%) 85-125/70-130. Penicillin 85-115 5.0 g/lb (1.1%) 85-125/70-130. Sulfamethazine 85.../lb (2.2%) 70-130. Penicillin 80-120 5.0 g/lb (1.1%) 70-130. Thiabendazole 94-106 45.4 g/lb (10.0%) >7...

21 CFR 558.4 - Requirement of a medicated feed mill license.

Code of Federal Regulations, 2012 CFR

2012-04-01

.../ton 75-125. Oxytetracycline 90-120 20.0 g/lb (4.4%) 75-125/65-135. Penicillin 80-120 10.0 g/lb (2.2... 10.0 g/lb (2.2%) 85-125/70-130. Penicillin 85-115 5.0 g/lb (1.1%) 85-125/70-130. Sulfamethazine 85.../lb (2.2%) 70-130. Penicillin 80-120 5.0 g/lb (1.1%) 70-130. Thiabendazole 94-106 45.4 g/lb (10.0%) >7...

The effects of physical and chemical preprocessing on the flowability of corn stover

DOE PAGES

Crawford, Nathan C.; Nagle, Nick; Sievers, David A.; ...

2015-12-20

Continuous and reliable feeding of biomass is essential for successful biofuel production. However, the challenges associated with biomass solids handling are commonly overlooked. In this study, we examine the effects of preprocessing (particle size reduction, moisture content, chemical additives, etc.) on the flow properties of corn stover. Compressibility, flow properties (interparticle friction, cohesion, unconfined yield stress, etc.), and wall friction were examined for five corn stover samples: ground, milled (dry and wet), acid impregnated, and deacetylated. The ground corn stover was found to be the least compressible and most flowable material. The water and acid impregnated stovers had similar compressibilities.more » Yet, the wet corn stover was less flowable than the acid impregnated sample, which displayed a flow index equivalent to the dry, milled corn stover. The deacetylated stover, on the other hand, was the most compressible and least flowable examined material. However, all of the tested stover samples had internal friction angles >30°, which could present additional feeding and handling challenges. All of the ''wetted'' materials (water, acid, and deacetylated) displayed reduced flowabilities (excluding the acid impregnated sample), and enhanced compressibilities and wall friction angles, indicating the potential for added handling issues; which was corroborated via theoretical hopper design calculations. All of the ''wetted'' corn stovers require larger theoretical hopper outlet diameters and steeper hopper walls than the examined ''dry'' stovers.« less

The effects of physical and chemical preprocessing on the flowability of corn stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, Nathan C.; Nagle, Nick; Sievers, David A.

Continuous and reliable feeding of biomass is essential for successful biofuel production. However, the challenges associated with biomass solids handling are commonly overlooked. In this study, we examine the effects of preprocessing (particle size reduction, moisture content, chemical additives, etc.) on the flow properties of corn stover. Compressibility, flow properties (interparticle friction, cohesion, unconfined yield stress, etc.), and wall friction were examined for five corn stover samples: ground, milled (dry and wet), acid impregnated, and deacetylated. The ground corn stover was found to be the least compressible and most flowable material. The water and acid impregnated stovers had similar compressibilities.more » Yet, the wet corn stover was less flowable than the acid impregnated sample, which displayed a flow index equivalent to the dry, milled corn stover. The deacetylated stover, on the other hand, was the most compressible and least flowable examined material. However, all of the tested stover samples had internal friction angles >30°, which could present additional feeding and handling challenges. All of the ''wetted'' materials (water, acid, and deacetylated) displayed reduced flowabilities (excluding the acid impregnated sample), and enhanced compressibilities and wall friction angles, indicating the potential for added handling issues; which was corroborated via theoretical hopper design calculations. All of the ''wetted'' corn stovers require larger theoretical hopper outlet diameters and steeper hopper walls than the examined ''dry'' stovers.« less

Process for Transition of Uranium Mill Tailings Radiation Control Act Title II Disposal Sites to the U.S. Department of Energy Office of Legacy Management for Long-Term Surveillance and Maintenance

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This document presents guidance for implementing the process that the U.S. Department of Energy (DOE) Office of Legacy Management (LM) will use for assuming perpetual responsibility for a closed uranium mill tailings site. The transition process specifically addresses sites regulated under Title II of the Uranium Mill Tailings Radiation Control Act (UMTRCA) but is applicable in principle to the transition of sites under other regulatory structures, such as the Formerly Utilized Sites Remedial Action Program.

A microcomputed tomography evaluation of the marginal fit of cobalt-chromium alloy copings fabricated by new manufacturing techniques and alloy systems.

PubMed

Kim, Eun-Ha; Lee, Du-Hyeong; Kwon, Sung-Min; Kwon, Tae-Yub

2017-03-01

Although new digital manufacturing techniques are attracting interest in dentistry, few studies have comprehensively investigated the marginal fit of fixed dental prostheses fabricated with such techniques. The purpose of this in vitro microcomputed tomography (μCT) study was to evaluate the marginal fit of cobalt-chromium (Co-Cr) alloy copings fabricated by casting and 3 different computer-aided design and computer-aided manufacturing (CAD-CAM)-based processing techniques and alloy systems. Single Co-Cr metal crowns were fabricated using 4 different manufacturing techniques: casting (control), milling, selective laser melting, and milling/sintering. Two different commercial alloy systems were used for each fabrication technique (a total of 8 groups; n=10 for each group). The marginal discrepancy and absolute marginal discrepancy of the crowns were determined with μCT. For each specimen, the values were determined from 4 different regions (sagittal buccal, sagittal lingual, coronal mesial, and coronal distal) by using imaging software and recorded as the average of the 4 readings. For each parameter, the results were statistically compared with 2-way analysis of variance and appropriate post hoc analysis (using Tukey or Student t test) (α=.05). The milling and selective laser melting groups showed significantly larger marginal discrepancies than the control groups (70.4 ±12.0 and 65.3 ±10.1 μm, respectively; P<.001), whereas the milling/sintering groups exhibited significantly smaller values than the controls (P=.004). The milling groups showed significantly larger absolute marginal discrepancy than the control groups (137.4 ±29.0 and 139.2 ±18.9 μm, respectively; P<.05). In the selective laser melting and milling/sintering groups, the absolute marginal discrepancy values were material-specific (P<.05). Nonetheless, the milling/sintering groups yielded statistically comparable (P=.935) or smaller (P<.001) absolute marginal discrepancies to the control groups. The findings of this in vitro μCT study showed that the marginal fit values of the Co-Cr alloy greatly depended on the fabrication methods and, occasionally, the alloy systems. Fixed dental prostheses produced by using the milling/sintering technique can be considered clinically acceptable in terms of marginal fit. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Microcidal effects of a new pelleting process.

PubMed

Ekperigin, H E; McCapes, R H; Redus, R; Ritchie, W L; Cameron, W J; Nagaraja, K V; Noll, S

1990-09-01

The microcidal efficiency of a new pelleting process was evaluated in four trials. Also, different methods of measuring temperature and moisture were compared and attempts were made to determine the influence on efficiency of pH changes occurring during processing. In the new process, the traditional boiler-conditioner was replaced by an Anaerobic Pasteurizing Conditioning (APC) System. Microcidal efficiency of the APC System, by itself or in conjunction with a pellet mill, appeared to be 100% against Escherichia coli and nonlactose-fermenters, 99% against aerobic mesophiles, and 90% against fungi. These levels of efficiency were attained when the temperature and moisture of feed conditioned in the APC System for 4.6 +/- .5 min were 82.9 +/- 2.4 C and 14.9 +/- .3%, respectively. On-line temperature probes were reliable and provided quick, accurate estimates of feed temperature. The near infrared scanner and microwave oven methods of measuring moisture were much quicker but less accurate than the in vacuo method. There were no differences among the pH of samples of raw, conditioned, and pelleted feed.

Synthesis of Nano-Crystalline Cu-Cr Alloy by Mechanical Alloying

NASA Astrophysics Data System (ADS)

Sheibani, S.; Heshmati-Manesh, S.; Ataie, A.

In this paper, the influence of toluene as the process control agent (PCA) and pre-milling on the extension of solid solubility of 7 wt.% Cr in Cu by mechanical alloying in a high energy ball mill was investigated. The structural evolution and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques, respectively. The solid solution formation at different conditions was analyzed by copper lattice parameter change during the milling process. It was found that both the presence of PCA and pre-milling of Cr powder lead to faster dissolution of Cr. The mean crystallite size was also calculated and showed to be about 10 nm after 80 hours of milling.

Development of the first force-controlled robot for otoneurosurgery.

PubMed

Federspil, Philipp A; Geisthoff, Urban W; Henrich, Dominik; Plinkert, Peter K

2003-03-01

In some surgical specialties (eg, orthopedics), robots are already used in the operating room for bony milling work. Otological surgery and otoneurosurgery may also greatly benefit from the enhanced precision of robotics. Experimental study on robotic milling of oak wood and human temporal bone specimen. A standard industrial robot with a six-degrees-of-freedom serial kinematics was used, with force feedback to proportionally control the robot speed. Different milling modes and characteristic path parameters were evaluated to generate milling paths based on computer-aided design (CAD) geometry data of a cochlear implant and an implantable hearing system. The best-suited strategy proved to be the spiral horizontal milling mode with the burr held perpendicular to the temporal bone surface. To reduce groove height, the distance between paths should equal half the radius of the cutting burr head. Because of the vibration of the robot's own motors, a high oscillation of the SD of forces was encountered. This oscillation dropped drastically to nearly 0 Newton (N) when the burr head made contact with the dura mater, because of its damping characteristics. The cutting burr could be kept in contact with the dura mater for an extended period without damaging it, because of the burr's blunt head form. The robot moved the burr smoothly according to the encountered resistances. The study reports the first development of a functional robotic milling procedure for otoneurosurgery with force-based speed control. Future plans include implementation of ultrasound-based local navigation and performance of robotic mastoidectomy.

Growth response of broilers to spray-dried plasma in pelleted or expanded feed processed at high temperature.

PubMed

Campbell, J M; Russell, L E; Crenshaw, J D; Behnke, K C; Clark, P M

2006-09-01

A series of 4 experiments evaluated effects of mash conditioning temperature from a pellet mill or expander on performance of broilers fed pelleted diets containing spray-dried plasma (SDP). All experiments utilized Ross x Ross 308 male broilers randomly assigned to their respective treatments (6 or 10 broilers/pen and 8 or 10 pens/treatment). Treatments in Exp. 1 consisted of a control (0% SDP), SDP coated postpelleting, or SDP blended into the meal prepelleting. Experiment 2 and 3 included the same 3 treatments as in Exp. 1 but with additional treatments of SDP blended into the meal and conditioned at 90 or 95 degrees C before pelleting. In Exp. 4, treatments consisted of a control (0% SDP) or SDP blended into the meal and pelleted (85 degrees C conditioning temperature) or expanded (149 degrees C final effective temperature) and then pelleted. Corn-soybean meal-based diets were formulated to be equal in lysine and ME in all experiments. Pelleted diets were conditioned for 15 s at 85 degrees C, and expanded diets were conditioned at 95 degrees C, 29.7 MJ/t, 13.95 kg/cm2 cone pressure, exit temperature of 149 degrees C, and then pelleted through a 4 x 32-mm die. In Exp. 1, ADG and feed intake were improved (P < 0.05) for broilers fed SDP from d 1 to 28 of age, with greater BW at d 42. In Exp. 2, both in early (d 1 to 28 of age) phases, and overall (d 1 to 42 of age), broilers fed SDP had improved (P < 0.05) gain and efficiency. In Exp. 3, ADG, feed intake, efficiency of gain, and BW were improved (P < 0.01) for broilers fed SDP from d 1 to 21 of age, regardless of conditioning temperature. In Exp. 4, broilers fed SDP had improved (P < 0.05) gain, BW, and feed intake regardless of processing method. Overall, the results of all of the experiments demonstrated that pellet conditioning temperature from 85 to 95 degrees C and expander temperatures to 149 degrees C did not impair the positive growth effects of SDP in pelleted or expanded broiler feed.

Cell morphology, viability, osteocalcin activity, and alkaline phosphatase activity in milled versus unmilled surface of the femoral head.

PubMed

Rhyu, Kee Hyung; Cho, Chang Hoon; Yoon, Kyung Sik; Chun, Young Soo

2016-12-01

To evaluate cellular activity in milled versus unmilled surface of the femoral head in 21 patients who underwent robot-assisted total hip arthroplasty(THA). The femoral head of 21 consecutive patients who underwent robot-assisted THA for osteonecrosis was used. 10 cc of trabecular bone from the entire milled surface was obtained using a curette. The same amount of trabecular bone was obtained at least 1 cm away from the milled surface and served as a matched control. Cell morphology, viability, osteocalcin activity, and alkaline phosphatase activity in milled versus unmilled surface were assessed. Cell morphology of the milled or unmilled surface was comparable; cells were smaller in the milled surface. Cell viability was a mean of 40% higher in the milled surface (107.4% vs. 67.2%, p<0.001); cell viability at 5 time points was comparable in each group. Osteocalcin activity of cells was slightly higher in the milled surface (1.43 vs. 1.24 ng/ml, p=0.69). Alkaline phosphatase activity of cells was slightly higher in the unmilled surface (150 105 vs. 141 789 U/L, p=0.078). The milled and unmilled surfaces of the femoral head were comparable in terms of cell morphology, viability, osteocalcin activity, and alkaline phosphatase activity.

Study on mycoflora of poultry feed ingredients and finished feed in Iran

PubMed Central

Ghaemmaghami, Seyed Soheil; Modirsaneii, Mehrdad; Khosravi, Ali Reza; Razzaghi-Abyaneh, Mehdi

2016-01-01

Background and Objectives: Unhygienic poultry feedstuffs can lead to nutrient losses and detrimental effect on poultry production and public health. In the present study, mycobiota and colony-forming units per gram in ingredients and finish poultry feed was evaluated with special reference to potentially mycotoxigenic fungi. Materials and Methods: Eighty five samples of corn, soybean meal and poultry finished feed were collected from nine poultry feed factories located in three provinces i.e. Tehran, Alborz and Qom in Iran from October 2014 to January 2015. Samples were cultured on Sabouraud dextrose agar (SDA), Aspergillus flavus and parasiticus agar (AFPA) and dichloran rosebengal chloramphenicol agar (DRBC) and incubated at 28 °C for 7–10 days. Purified fungal colonies were identified by a combination of macro- and microscopic morphological criteria. For determining the rate of fungal contamination, samples were cultured on SDA and colony forming units (CFUs) were calculated. Results: A total of 384 fungal isolates belonging to 7 genera of filamentous fungi and yeasts were obtained from corn (124 isolates), soybean meal (92 isolates), and feed before (72 isolates), and after pelleting (96 isolates). The most prominent fungal isolate in corn, soybean meal and feed before pelleting (feed as mash form) was Fusarium but in feed after pelleting was Aspergillus. Among 5 Aspergillus species isolated, potentially aflatoxigenic A. flavus isolates was predominant in corn (46.6%), soybean meal (72.7%) and poultry finished feed (75%). CFUs results indicated that 9/22 corn samples (40.9%), none of 22 soybean meal samples, 19/41 finished feed (46.3%) were contaminated higher than the standard limit. Conclusions: Our results indicated that corn, soybean meal and finished feed of poultry feed mill are contaminated with various fungal genera by different levels sometimes higher that the standard limits. Contamination with potentially mycotoxigenic fungi especially Aspergillus species may be considered as a human public health hazard. PMID:27092224

Study on mycoflora of poultry feed ingredients and finished feed in Iran.

PubMed

Ghaemmaghami, Seyed Soheil; Modirsaneii, Mehrdad; Khosravi, Ali Reza; Razzaghi-Abyaneh, Mehdi

2016-02-01

Unhygienic poultry feedstuffs can lead to nutrient losses and detrimental effect on poultry production and public health. In the present study, mycobiota and colony-forming units per gram in ingredients and finish poultry feed was evaluated with special reference to potentially mycotoxigenic fungi. Eighty five samples of corn, soybean meal and poultry finished feed were collected from nine poultry feed factories located in three provinces i.e. Tehran, Alborz and Qom in Iran from October 2014 to January 2015. Samples were cultured on Sabouraud dextrose agar (SDA), Aspergillus flavus and parasiticus agar (AFPA) and dichloran rosebengal chloramphenicol agar (DRBC) and incubated at 28 °C for 7-10 days. Purified fungal colonies were identified by a combination of macro- and microscopic morphological criteria. For determining the rate of fungal contamination, samples were cultured on SDA and colony forming units (CFUs) were calculated. A total of 384 fungal isolates belonging to 7 genera of filamentous fungi and yeasts were obtained from corn (124 isolates), soybean meal (92 isolates), and feed before (72 isolates), and after pelleting (96 isolates). The most prominent fungal isolate in corn, soybean meal and feed before pelleting (feed as mash form) was Fusarium but in feed after pelleting was Aspergillus. Among 5 Aspergillus species isolated, potentially aflatoxigenic A. flavus isolates was predominant in corn (46.6%), soybean meal (72.7%) and poultry finished feed (75%). CFUs results indicated that 9/22 corn samples (40.9%), none of 22 soybean meal samples, 19/41 finished feed (46.3%) were contaminated higher than the standard limit. Our results indicated that corn, soybean meal and finished feed of poultry feed mill are contaminated with various fungal genera by different levels sometimes higher that the standard limits. Contamination with potentially mycotoxigenic fungi especially Aspergillus species may be considered as a human public health hazard.

Role of climatic factors on damage incidence by Dermolepida albohirtum (Coleoptera: Scarabaeidae), in Burdekin sugarcane fields, Australia.

PubMed

Horsfield, Andrew; Sallam, Mohamed Nader S; Drummond, Frank A; Williams, Don J; Schultz, Rod J

2008-04-01

Inconsistent control of Dermolepida albohirtum (Waterhouse) (Coleoptera: Scarabaeidae) in the period after the removal of organochlorines allowed us to study the impact of climatic variables and insecticide application on subsequent damage in sugarcane (Saccharum spp.). D. albohirtum damage records from the Invicta and Inkerman mill areas of the Burdekin district of North Queensland were compared with climatic averages during spring from 1989 to 2003. D. albohirtum damage demonstrated autocorrelation, indicating that the area of damage will increase from one year to the next if the grub is not effectively controlled. Insecticide use did not significantly impact on the area of damage between 1989 and 2003. Of the climatic variables evaluated, only pan evaporation was significant, and it was inversely related to the subsequent area of grub damage. Therefore, we suggest that weather conditions in spring impact on beetle emergence, feeding, and oviposition. Hot and dry spring weather may reduce beetle activity and ultimately the severity of crop damage, whereas wet and mild spring weather may favor beetle activity and an increase in the area of potential crop damage.

Carbohydrate composition and in vitro digestibility of dry matter and nonstarch polysaccharides in corn, sorghum, and wheat and coproducts from these grains.

PubMed

Jaworski, N W; Lærke, H N; Bach Knudsen, K E; Stein, H H

2015-03-01

The objectives of this work were to determine carbohydrate composition and in vitro digestibility of DM and nonstarch polysaccharides (NSP) in corn, wheat, and sorghum and coproducts from these grains. In the initial part of this work, the carbohydrate composition of 12 feed ingredients was determined. The 12 ingredients included 3 grains (corn, sorghum, and wheat), 3 coproducts from the dry grind industry (corn distillers dried grains with solubles [DDGS] and 2 sources of sorghum DDGS), 4 coproducts from the wet milling industry (corn gluten meal, corn gluten feed, corn germ meal, and corn bran), and 2 coproducts from the flour milling industry (wheat middlings and wheat bran). Results indicated that grains contained more starch and less NSP compared with grain coproducts. The concentration of soluble NSP was low in all ingredients. Cellulose, arabinoxylans, and other hemicelluloses made up approximately 22, 49, and 29% (DM basis), respectively, of the NSP in corn and corn coproducts and approximately 25, 43, and 32% (DM basis), respectively, of the NSP in sorghum and sorghum DDGS. Cellulose, arabinoxylans, and other hemicelluloses made up approximately 16, 64, and 20% (DM basis), respectively, of the NSP in wheat and wheat coproducts. The concentration of lignin in grains was between 0.8 and 1.8% (DM basis), whereas coproducts contained between 2.2 and 11.5% lignin (DM basis). The in vitro ileal digestibility of NSP was close to zero or negative for all feed ingredients, indicating that pepsin and pancreas enzymes have no effect on in vitro degradation of NSP. A strong negative correlation ( = 0.97) between in vitro ileal digestibility of DM and the concentration of NSP in feed ingredients was observed. In vitro total tract digestibility of NSP ranged from 6.5% in corn bran to 57.3% in corn gluten meal. In conclusion, grains and grain coproducts contain mostly insoluble NSP and arabinoxylans make up the majority of the total NSP fraction. The in vitro digestibility of NSP depends on the amount and type of NSP and degree of lignification in the feed ingredient. The NSP composition of grains and grain coproducts plays an important role in determining the extent of fermentation of NSP; therefore, NSP composition influences the energy value of grains and grain coproducts.

10. Interior view of first floor showing 6 of 7 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Interior view of first floor showing 6 of 7 roller mills. All shown were manufactured by Allis-Chalmers. Wheel in foreground controls turbine speed. - Fisher-Fallgatter Mill, Waupaca, Waupaca County, WI

6. View of the end of the lower raceway showing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. View of the end of the lower raceway showing the gates and controlling mechanisms for channeling water into the Industry Mill. - Industry Mill, Van Houten & Prospect Street, Paterson, Passaic County, NJ

WATER POLLUTION ABATEMENT IN THE WISCONSIN PAPER INDUSTRY

EPA Science Inventory

The study estimates the costs incurred by paper mills in the State of Wisconsin to comply with water pollution control requirements and compares these costs to those incurred by similar mills in other states.

Improved Design Process Part of the Ship Producibility Program of the National Shipbuilding Research Program

DTIC Science & Technology

1977-04-01

Exh and Escape Fresh Water Feed Treatment Cargo Oil Tank Cleaning Diesel Generator Piping Piping Material Schedule List of Motors and... tank length frame and stiffener spacing, etc. One yard buys only mill edge plates, and one yard buys only cold flange quality plates. 2-13 C. POST...gage boards, all interconnecting piping and valves, and all mounted on a common foundation, or a pump room assembled on a tank top unit. Use of packages

21 CFR 558.4 - Requirement of a medicated feed mill license.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 90-120 20.0 g/lb (4.4%) 75-125/65-135. Penicillin 80-120 10.0 g/lb (2.2%) 65-135. Poloxalene 90-110... 10.0 g/lb (2.2%) 85-125/70-130. Penicillin 85-115 5.0 g/lb (1.1%) 85-125/70-130. Sulfamethazine 85.... Chlortetracycline 85-125 10.0g/lb (2.2%) 70-130. Penicillin 80-120 5.0 g/lb (1.1%) 70-130. Thiabendazole 94-106 45.4...

Growth and subsequent egg production performance of shika-brown pullets fed graded levels of cooked Lablab purpureus beans.

PubMed

Abeke, F O; Ogundipe, S O; Sekoni, A A; Dafwvang, I I; Adeyinka, I A; Oni, O O; Abeke, A

2007-04-01

The lablab seeds were cooked for 30 min, sundried for three days and thereafter milled and incorporated into chickens' diets. Six treatments, comprising of six dietary levels of lablab at 0.0, 7.5, 15.0, 22.5, 30.0 and 37.5%, respectively was fed during the grower's phase. Results obtained for the growers phase indicate that final weight (g/bird), weight gain (g/bird) and feed cost (N kg(-1)) decreased significantly (p < 0.05) as the level of lablab increased in the diet. Feed intake (g/bird and g/bird/day) as well as feed cost (N/bird) and total cost (N/bird) also decreased significantly (p < 0.05) as the level oflablab increased in the diet up to 22.5% inclusion level before increasing as the level of lablab in the diets continued to increase. The level of lablab in the diet had no effect on mortality throughout the experimental period. In addition haematological parameters such as Packed Cell Volume (PCV), Haemoglobin (Hb) and Total Protein (TP) were not significantly (p < 0.05) affected by feeding diets containing graded levels of cooked lablab beans to pullets. Results obtained during the laying phase indicates that feeding lablab seed meal up to 22.5% in the diets at the growers stage had no significant adverse effect (p < 0.05) on final weight, feed intake, feed efficiency, percent henday and henhoused egg production, percent production at peak, kilogramme feed per twelve eggs, feed cost per twelve eggs, Haugh Unit and yolk index. However, age of birds at first egg, age at 50% production and age at peak egg production were increased significantly (p > 0.05) with increase in the level of lablab seed meal in the growers diets.

Feasibility of utilization of horse dung spiked filter cake in vermicomposters using exotic earthworm Eisenia foetida.

PubMed

Sangwan, Pritam; Kaushik, C P; Garg, V K

2008-05-01

This contribution reports the potential of vermicomposting technology in the management of horse dung (HD) spiked sugar mill filter cake (SMFC) using an epigeic earthworm Eisenia foetida under laboratory conditions. A total of six vermicomposters filled with different ratios of HD and SMFC were maintained for this study. The growth and fecundity of E. foetida was monitored for 12 weeks. Maximum growth was recorded in 90% HD+10% SMFC feed mixture containing vermicomposter. Earthworms' biomass gain and reproduction was favorably up to 50% HD+50% SMFC feed composition. Maximum cocoons were also recorded in 90% HD+10% SMFC feed mixtures, however increasing proportions of SMFC in different vermicomposters affected the growth and fecundity of worms. A significant decrease in C:N ratio and increase in total kjeldahl nitrogen, total available phosphorus and calcium contents was recorded. The heavy metals content was higher in the vermicompost obtained in all the reactors than initial feed substrates. Based on investigations it is concluded that vermicomposting could be an alternative technology for the management of filter cake if it is mixed in 1:1 ratio with horse dung.

Analysis of sugar mill effluent and its influence on germination and growth of African marigold ( Tagetes erecta L.)

NASA Astrophysics Data System (ADS)

Vaithiyanathan, Thanapal; Sundaramoorthy, Perumal

2017-12-01

Sugar industry is a very important agro-based industry in India and it discharges large amount of effluent into water bodies to create high pollution in water bodies which affects the plants and other living organisms. In the present investigation, the physico-chemical analyses of N. P. K. R. Ramaswamy co-operative sugar mill effluent was determined and impact of different concentrations (control, 10, 25, 50, 75 and 100%) of sugar mill effluent on seed germination behavior of African marigold ( Tagetes erecta L.) was studied. The morphological parameters such as germination percentage, shoot length, root length, fresh weight and dry weight of seedlings, seed vigour index, tolerance index and percentage of phytotoxicity were calculated. The results recorded for the analyses of sugar mill effluent indicated their some parameters such as PH, EC, acidity, TDS, TS, BOD, COD, sulphate, magnesium, nitrogen, zinc, iron, copper, lead, manganese and oil and grease exceeded the permissible limit compared to Tamil Nadu Pollution Control Board (TNPCB) and then germination and growth parameters increased in lower (10%) concentration of sugar mill effluent and this morphological parameters gradually decreased with increasing effluent concentration. The lower (10%) concentration of sugar mill effluent may be used for irrigation purposes.

[Distribution and environmental conditions related to the behavior in the bottlenose dolphin (Tursiops truncatus) and the spotted dolphin (Stenella attenuata) (Cetacea: Delphinidae) in Golfo Dulce, Costa Rica].

PubMed

Cubero-Pardo, Priscilla

2007-06-01

Habitat characteristics influencing behavior in animal species vary locally. The influence that a particular environmental characteristic can have on a species depends not only on other variables, but on morphological, physiological and social conditions of that species. In this study, developed from June 1996 to July 1997, I studied whether specific behaviors are related to particular distribution areas and environmental factors in the bottlenose (Tursiops truncatus) and the spotted dolphin (Stenella attenuata). The study area was covered along oblicuous linear transects, and the behavior of single groups was observed from 15 min to 5 h. Environmental factors such as depth, temperature, salinity and distance from shore, among others, were considered. For the bottlenose dolphin, foraging/feeding activities showed exclusive coincidence with river mouths, coral reef and mangrove areas, while social and milling activities where seen close to feeding areas. Traveling occurred along different points parallel to the coast, with a low percentage of cases across the gulf (16.56 %), suggesting that the bottlenose rarely crosses from one side to the other. In the spotted dolphin, several behaviors were observed simultaneously in the schools and it was not possible to associate areas with particular behaviors. The lack of significant relationships among activities and particular environmental variables (ANOVA tests) is attributed to three aspects: (a) transitions among activities generally occurred into a low variable area, (b) dolphins often traveled along large areas without changing activities and (c) environmental conditions in Golfo Dulce are homogeneous. In the two species the highest average in the number of individuals per group corresponded to the category of active socializing, followed by traveling, passive socializing and feeding. In the case of the bottlenose dolphin, the smallest group size was associated with feeding activities (ANOVA, F= 2.624, p=0.037, n=156, df=4), while in the spotted dolphin the smallest group size corresponded to milling activities (ANOVA, F=3.817, p=0.009, n=51, df=4).

Radiation dosimetry on revegetated uranium mill tailings in western South Dakota

Treesearch

Mark A. Rumble

1986-01-01

Measurement of gamma radiation using thermoluminescent dosimeters on three uranium mill tailings areas and a control area showed exposure rates below ground depended on the amount and type of soil covering. Covering tailings with 30 cm of shale and 60 cm of topsoil reduced gamma radiation exposure belowground to rates similar to the control area. Soil covering of 30 cm...

Effect of hydroalcoholic fruit extract of Persea americana Mill. on high fat diet induced obesity: A dose response study in rats.

PubMed

Monika, Padmanabhan; Geetha, Arumugam

2016-06-01

The fruits of Persea Americana Mill., commonly known as Avocado, are traditionally consumed for various health benefits including weight reduction. Here, we studied the effect of hydroalcoholic fruit extract of Persea americana (HAEPA) on high fat diet (HFD) induced obesity in rats. Obesity was induced in male Sprague Dawley rats by feeding HFD for 14 wk. The hypolipidemic effect was evaluated by co-administering 25, 50, 100 and 200 mg/kg body wt. of HAEPA. There was a significant increase in weight gain, body mass index (BMI), blood lipids, low density lipoproteins (LDL), lipid peroxides (LPO) and serum transaminases in HFD fed rats. HFD+HAEPA fed rats showed a significant decrease in blood lipids, LPO, liver lipids and increase in antioxidant status when compared to HFD control rats. The activity of lipid metabolic key enzymes such as fatty acid synthase and HMG CoA reductase in liver were also found to be decreased significantly in HAEPA co-administered rats. Lipoprotein lipase activity was found increased in HFD+HAEPA rats. Among the 4 doses studied, 100 mg of HAEPA/kg body wt. exhibited optimum hypolipidemic activity. Histopathological observations in liver and visceral adipose tissue added more evidence for the lipid lowering effect of HAEPA. It can be concluded that avocado fruit extract can act as hypolipidemic agent probably by modulating the activities of HMG CoA reductase and fatty acid synthase in liver.

Effects of processing, particle size and moisturizing of sorghum-based feeds on pellet quality and broiler production.

PubMed

da Silva, Patrícia Garcia; Oliveira, Luana Martins Schaly; de Oliveira, Nayanne Rodrigues; de Moura Júnior, Fábio Ataides; Silva, Maura Regina Sousa; Cordeiro, Deibity Alves; Minafra, Cibele Silva; Dos Santos, Fabiana Ramos

2018-01-01

This study aimed to assess the effect of pelleted and expanded sorghum-based feeds prepared with different moisture levels and particle size of ingredients on metabolizable energy, ileal digestibility of amino acids and broiler performance. The experiment was performed with 720 male broiler chicks of the Cobb strain, with treatments of six replications, with 15 birds each; they were arranged in a completely randomized design and 2×2×2 factorial scheme (pelleted or expanded feed processing, 0.8% or 1.6% moisture addition in the mixer, and particle size of 650 or 850 microns). Higher pellet quality (pellets, % and pellet durability index [PDI]) was obtained in expanded diets and inclusion of 1.6% moisture. The particle size of 850 microns increased the PDI of final diet. All studied treatments had no significant effect on weight gain and broiler carcass and cut yields. Lower feed conversion occurred for birds fed pelleted feed at 42 d. The highest apparent metabolizable energy (AME) and apparent metabolizable energy corrected to zero nitrogen balance (AMEn) values of feed in the initial rearing phase (10 to 13 days) were observed in birds fed pelleted feed or for feed prepared with 1.6% moisture. The highest ileal digestibility coefficients of amino acids were obtained with the consumption of pelleted feed prepared with a particle size of 650 microns and 1.6% moisture. Pelleted feed prepared with a milling particle size of 650 microns and 1.6% moisture provided increased ileal digestibility of amino acids and AMEn in the starter period. However, the expanded feed improved pellet quality and feed conversion of broilers at 42 days of age. We conclude that factors such as moisture, particle size and processing affect the pellet quality, and therefore should be considered when attempting to optimize broiler performance.

Humpback whale “super-groups” – A novel low-latitude feeding behaviour of Southern Hemisphere humpback whales (Megaptera novaeangliae) in the Benguela Upwelling System

PubMed Central

Seakamela, S. Mduduzi; Meÿer, Michael A.; Kirkman, Stephen P.; Barendse, Jaco; Cade, David E.; Hurwitz, David; Kennedy, Amy S.; Kotze, Pieter G. H.; McCue, Steven A.; Thornton, Meredith; Vargas-Fonseca, O. Alejandra; Wilke, Christopher G.

2017-01-01

Southern Hemisphere humpback whales (Megaptera novaeangliae) generally undertake annual migrations from polar summer feeding grounds to winter calving and nursery grounds in subtropical and tropical coastal waters. Evidence for such migrations arises from seasonality of historic whaling catches by latitude, Discovery and natural mark returns, and results of satellite tagging studies. Feeding is generally believed to be limited to the southern polar region, where Antarctic krill (Euphausia superba) has been identified as the primary prey item. Non-migrations and / or suspended migrations to the polar feeding grounds have previously been reported from a summer presence of whales in the Benguela System, where feeding on euphausiids (E. lucens), hyperiid amphipods (Themisto gaudichaudii), mantis shrimp (Pterygosquilla armata capensis) and clupeid fish has been described. Three recent research cruises (in October/November 2011, October/November 2014 and October/November 2015) identified large tightly-spaced groups (20 to 200 individuals) of feeding humpback whales aggregated over at least a one-month period across a 220 nautical mile region of the southern Benguela System. Feeding behaviour was identified by lunges, strong milling and repetitive and consecutive diving behaviours, associated bird and seal feeding, defecations and the pungent “fishy” smell of whale blows. Although no dedicated prey sampling could be carried out within the tightly spaced feeding aggregations, observations of E. lucens in the region of groups and the full stomach contents of mantis shrimp from both a co-occurring predatory fish species (Thyrsites atun) and one entangled humpback whale mortality suggest these may be the primary prey items of at least some of the feeding aggregations. Reasons for this recent novel behaviour pattern remain speculative, but may relate to increasing summer humpback whale abundance in the region. These novel, predictable, inter-annual, low latitude feeding events provide considerable potential for further investigation of Southern Hemisphere humpback feeding behaviours in these relatively accessible low-latitude waters. PMID:28249036

Humpback whale "super-groups" - A novel low-latitude feeding behaviour of Southern Hemisphere humpback whales (Megaptera novaeangliae) in the Benguela Upwelling System.

PubMed

Findlay, Ken P; Seakamela, S Mduduzi; Meÿer, Michael A; Kirkman, Stephen P; Barendse, Jaco; Cade, David E; Hurwitz, David; Kennedy, Amy S; Kotze, Pieter G H; McCue, Steven A; Thornton, Meredith; Vargas-Fonseca, O Alejandra; Wilke, Christopher G

2017-01-01

Southern Hemisphere humpback whales (Megaptera novaeangliae) generally undertake annual migrations from polar summer feeding grounds to winter calving and nursery grounds in subtropical and tropical coastal waters. Evidence for such migrations arises from seasonality of historic whaling catches by latitude, Discovery and natural mark returns, and results of satellite tagging studies. Feeding is generally believed to be limited to the southern polar region, where Antarctic krill (Euphausia superba) has been identified as the primary prey item. Non-migrations and / or suspended migrations to the polar feeding grounds have previously been reported from a summer presence of whales in the Benguela System, where feeding on euphausiids (E. lucens), hyperiid amphipods (Themisto gaudichaudii), mantis shrimp (Pterygosquilla armata capensis) and clupeid fish has been described. Three recent research cruises (in October/November 2011, October/November 2014 and October/November 2015) identified large tightly-spaced groups (20 to 200 individuals) of feeding humpback whales aggregated over at least a one-month period across a 220 nautical mile region of the southern Benguela System. Feeding behaviour was identified by lunges, strong milling and repetitive and consecutive diving behaviours, associated bird and seal feeding, defecations and the pungent "fishy" smell of whale blows. Although no dedicated prey sampling could be carried out within the tightly spaced feeding aggregations, observations of E. lucens in the region of groups and the full stomach contents of mantis shrimp from both a co-occurring predatory fish species (Thyrsites atun) and one entangled humpback whale mortality suggest these may be the primary prey items of at least some of the feeding aggregations. Reasons for this recent novel behaviour pattern remain speculative, but may relate to increasing summer humpback whale abundance in the region. These novel, predictable, inter-annual, low latitude feeding events provide considerable potential for further investigation of Southern Hemisphere humpback feeding behaviours in these relatively accessible low-latitude waters.

Effects of processing, particle size and moisturizing of sorghum-based feeds on pellet quality and broiler production

PubMed Central

2018-01-01

Objective This study aimed to assess the effect of pelleted and expanded sorghum-based feeds prepared with different moisture levels and particle size of ingredients on metabolizable energy, ileal digestibility of amino acids and broiler performance. Methods The experiment was performed with 720 male broiler chicks of the Cobb strain, with treatments of six replications, with 15 birds each; they were arranged in a completely randomized design and 2×2×2 factorial scheme (pelleted or expanded feed processing, 0.8% or 1.6% moisture addition in the mixer, and particle size of 650 or 850 microns). Results Higher pellet quality (pellets, % and pellet durability index [PDI]) was obtained in expanded diets and inclusion of 1.6% moisture. The particle size of 850 microns increased the PDI of final diet. All studied treatments had no significant effect on weight gain and broiler carcass and cut yields. Lower feed conversion occurred for birds fed pelleted feed at 42 d. The highest apparent metabolizable energy (AME) and apparent metabolizable energy corrected to zero nitrogen balance (AMEn) values of feed in the initial rearing phase (10 to 13 days) were observed in birds fed pelleted feed or for feed prepared with 1.6% moisture. The highest ileal digestibility coefficients of amino acids were obtained with the consumption of pelleted feed prepared with a particle size of 650 microns and 1.6% moisture. Conclusion Pelleted feed prepared with a milling particle size of 650 microns and 1.6% moisture provided increased ileal digestibility of amino acids and AMEn in the starter period. However, the expanded feed improved pellet quality and feed conversion of broilers at 42 days of age. We conclude that factors such as moisture, particle size and processing affect the pellet quality, and therefore should be considered when attempting to optimize broiler performance. PMID:28920405

Valorization of solid waste products from olive oil industry as potential adsorbents for water pollution control--a review.

PubMed

Bhatnagar, Amit; Kaczala, Fabio; Hogland, William; Marques, Marcia; Paraskeva, Christakis A; Papadakis, Vagelis G; Sillanpää, Mika

2014-01-01

The global olive oil production for 2010 is estimated to be 2,881,500 metric tons. The European Union countries produce 78.5% of the total olive oil, which stands for an average production of 2,136,000 tons. The worldwide consumption of olive oil increased of 78% between 1990 and 2010. The increase in olive oil production implies a proportional increase in olive mill wastes. As a consequence of such increasing trend, olive mills are facing severe environmental problems due to lack of feasible and/or cost-effective solutions to olive-mill waste management. Therefore, immediate attention is required to find a proper way of management to deal with olive mill waste materials in order to minimize environmental pollution and associated health risks. One of the interesting uses of solid wastes generated from olive mills is to convert them as inexpensive adsorbents for water pollution control. In this review paper, an extensive list of adsorbents (prepared by utilizing different types of olive mill solid waste materials) from vast literature has been compiled, and their adsorption capacities for various aquatic pollutants removal are presented. Different physicochemical methods that have been used to convert olive mill solid wastes into efficient adsorbents have also been discussed. Characterization of olive-based adsorbents and adsorption mechanisms of various aquatic pollutants on these developed olive-based adsorbents have also been discussed in detail. Conclusions have been drawn from the literature reviewed, and suggestions for future research are proposed.

Comparison of control and quality of bone cutting by using optical topographical imaging guided mechanical drill and 1070 nm laser with in-line coherent imaging

NASA Astrophysics Data System (ADS)

Razani, Marjan; Soudagar, Yasaman; Yu, Karen; Galbraith, Christopher M.; Webster, Paul J. L.; Van Vlack, Cole; Sun, Cuiru; Mariampillai, Adrian; Leung, Michael K. K.; Standish, Beau; Kiehl, Tim-Rasmus; Fraser, James M.; Yang, Victor X. D.

2013-03-01

Precision depth control of bone resection is necessary for safe surgical procedures in the spine. In this paper, we compare the control and quality of cutting bovine tail bone, as an ex vivo model of laminectomy and bony resection simulating spinal surgery, planned with micro-CT data and executed using two approaches: (a) mechanical milling guided by optical topographical imaging (OTI) and (b) optical milling using closed-loop inline coherent imaging (ICI) to monitor and control the incision depth of a high-power 1070 nm fiber laser in situ. OTI provides the in situ topology of the 2-dimensional surface of the bone orientation in the mechanical mill which is registered with the treatment plan derived from the micro-CT data. The coregistration allows the plan to be programmed into the mill which is then used as a benchmark of current surgical techniques. For laser cutting, 3D optical land marking with coaxial camera vision and the ICI system is used to coregister the treatment plan. The unstable, carbonization-mediated ablation behaviour of 1070 nm light and the unknown initial geometry of bone leads to unpredictable ablation which substantially limits the depth accuracy of open-loop cutting. However, even with such a non-ideal cutting laser, we demonstrate that ICI provides in situ high-speed feedback that automatically and accurately limits the laser's cut depth to effectively create an all-optical analogue to the mechanical mill.

75 FR 6337 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control of Carbon...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... Oxygen Furnaces AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule. SUMMARY: EPA... basic oxygen furnaces (BOFs) at steel mills with a new CO standard for BOFs at steel mills. In the Final...

Antifeedant compounds from three species of Apiaceae active against the field slug, Deroceras reticulatum (Muller).

PubMed

Birkett, Michael A; Dodds, Catherine J; Henderson, Ian F; Leake, Lucy D; Pickett, John A; Selby, Martin J; Watson, Peter

2004-03-01

Extracts of volatiles from foliage of three plants in the Apiaceae, Conium maculatum L. (hemlock), Coriandrum sativum L. (coriander), and Petroselinum crispum Mill. (Nym.) (parsley), previously shown to exhibit antifeedant activity in assays with the field slug, Deroceras reticulatum (Muller) (Limacidae: Pulmonata), were studied further to identify the active components. Coupled gas chromatography-mass spectrometry (GC-MS) and neurophysiological assays using tentacle nerve preparations resulted in the identification of 11 active compounds from the three extracts. Wheat flour feeding bioassays were used to determine which of these compounds had the highest antifeedant activity. One of the most active compounds was the alkaloid gamma-coniceine, from C. maculatum. The role of potentially toxic alkaloids as semiochemicals and the potential for using such compounds as crop protection agents to prevent slug feeding damage is discussed.

[Application of three control banding tools to occupational health risk assessment of titanium dioxide manufacturing factory].

PubMed

Xu, H D; Zhao, L; Tang, S C; Zhang, J; Kong, F L; Jia, G

2016-12-20

Objective: To explore and validate suitable risk assessment methods for titanium dioxide though applying three risk assessment tools for nanomaterials based on the control banding (CB) approach. Methods: A factory manufacturing titanium dioxide in Jinan city, Shandong province, was assessed using a quantitative exposure method and qualitative risk assessment methods in September, 2014. A condensation particle counter equipment was used to monitor the number concentration of particles at packaging workshop and jet milling workshop. We employed three control banding tools, including CB nanotool, Stoffenmanager nano and the Guidance on working safely with nanomaterials and nanoproducts (GWSNN) to evaluate the two workshops, then compared the evaluation results. Results: The increases of particle concentrations were generated directly by packaging and jet milling processes, the number concentration from (3.52±1.46) ×10(4)/cm(3) to (14.70±8.86) ×10(4)/cm(3) at packaging workshop and from (0.97±0.25) ×10(4)/cm(3) to (1.26±0.35) ×10(4)/cm(3) at milling workshop (both P <0.05) . The number concentrations at packaging workshop were higher than those at jet milling workshop during both manufacturing and break times (both P <0.05) . The results of CB nanotool showed that the risk level of the packaging workshop was classified as high and the risk level of the jet milling workshop was classified asmedium. The results of Stoffenmanager nano showed that the risk level of the packaging workshop was classified as medium and the risk level of the jet milling workshop was classified as low. The results of GWSNN showed that the risk level of packaging workshop was classified as high and the risk level of jet milling workshop was classified as low. Conclusion: The results of evaluation based on the three control banding tools are related and aligned with the results of quantitative monitoring, so they are all suitable to perform occupational health risk assessment on industrial scale production of titanium dioxideto some extent.

Preparation and physicochemical characterization of spray-dried and jet-milled microparticles containing bosentan hydrate for dry powder inhalation aerosols.

PubMed

Lee, Hyo-Jung; Kang, Ji-Hyun; Lee, Hong-Goo; Kim, Dong-Wook; Rhee, Yun-Seok; Kim, Ju-Young; Park, Eun-Seok; Park, Chun-Woong

2016-01-01

The objectives of this study were to prepare bosentan hydrate (BST) microparticles as dry powder inhalations (DPIs) via spray drying and jet milling under various parameters, to comprehensively characterize the physicochemical properties of the BST hydrate microparticles, and to evaluate the aerosol dispersion performance and dissolution behavior as DPIs. The BST microparticles were successfully prepared for DPIs by spray drying from feeding solution concentrations of 1%, 3%, and 5% (w/v) and by jet milling at grinding pressures of 2, 3, and 4 MPa. The physicochemical properties of the spray-dried (SD) and jet-milled (JM) microparticles were determined via scanning electron microscopy, atomic force microscopy, dynamic light scattering particle size analysis, Karl Fischer titration, surface analysis, pycnometry, differential scanning calorimetry, powder X-ray diffraction, and Fourier transform infrared spectroscopy. The in vitro aerosol dispersion performance and drug dissolution behavior were evaluated using an Anderson cascade impactor and a Franz diffusion cell, respectively. The JM microparticles exhibited an irregular corrugated surface and a crystalline solid state, while the SD microparticles were spherical with a smooth surface and an amorphous solid state. Thus, the in vitro aerosol dispersion performance and dissolution behavior as DPIs were considerably different due to the differences in the physicochemical properties of the SD and JM microparticles. In particular, the highest grinding pressures under jet milling exhibited excellent aerosol dispersion performance with statistically higher values of 56.8%±2.0% of respirable fraction and 33.8%±2.3% of fine particle fraction and lower mass median aerodynamic diameter of 5.0±0.3 μm than the others ( P <0.05, analysis of variance/Tukey). The drug dissolution mechanism was also affected by the physicochemical properties that determine the dissolution kinetics of the SD and JM microparticles, which were well fitted into the Higuchi and zero-order models, respectively.

Parametric Techniques for Multichannel Signal Processing.

DTIC Science & Technology

1985-10-01

AD-A165 649 PARAMETRIC TECHNIQUES FOR MULTICHANNEL SIGNAL PROCESSING(U) SYSTEM CONTROL TECHNOLOGY INC PALO RLTO CA B FRIEDLANDER OCT 85 5498-87 RRO...CONTRACT NO. DAAG29-83-C-0027 SYSTEMS CONTROL TECHNOLOGY, INC. DT1I? q4 1801 PAGE MILL ROAD ELI PALO ALTO, CALIFORNIA 94304EL C MAR 193 £4 APPROVED FOR...PROJECT, TASK Systems Control Technology, Inc. AREA & WORK UNIT NUMBERS 1801 Page Mill Road Palo Alto, CA 94304 II :ON?’ROLLING OFFICE NAME AND

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Durango, Colorado: Remedial action selection report. Revised final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-12-01

The uranium mill tailings site near Durango, Colorado, was one of 24 inactive uranium mill sites designated to be remediated by the US Department of Energy (DOE) under the Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA). Part of the UMTRCA requires that the US Nuclear Regulatory Commission (NRC) concur with the DOE`s Remedial Action Plan (RAP) and certify that the remedial action conducted at the site complies with the standards promulgated by the US Environmental Protection Agency (EPA). Included in the RAP is this Remedial Action Selection Report (RAS), which has been developed to serve a two-fold purpose.more » First, it describes the activities that have been conducted by the DOE to accomplish remediation and long-term stabilization and control of the radioactive materials at the inactive uranium mill processing site near Durango, Colorado. Secondly, this document and the rest of the RAP, upon concurrence and execution by the DOE, the State of Colorado, and the NRC, become Appendix B of the Cooperative Agreement between the DOE and the State of Colorado.« less

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Durango, Colorado: Remedial action selection report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-12-01

The uranium mill tailings site near Durango, Colorado, was one of 24 inactive uranium mill sites designated to be remediated by the US Department of Energy (DOE) under the Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA). Part of the UMTRCA requires that the US Nuclear Regulatory Commission (NRC) concur with the DOE's Remedial Action Plan (RAP) and certify that the remedial action conducted at the site complies with the standards promulgated by the US Environmental Protection Agency (EPA). Included in the RAP is this Remedial Action Selection Report (RAS), which has been developed to serve a two-fold purpose.more » First, it describes the activities that have been conducted by the DOE to accomplish remediation and long-term stabilization and control of the radioactive materials at the inactive uranium mill processing site near Durango, Colorado. Secondly, this document and the rest of the RAP, upon concurrence and execution by the DOE, the State of Colorado, and the NRC, become Appendix B of the Cooperative Agreement between the DOE and the State of Colorado.« less

Characterization of ball-milled carbon nanotube dispersed aluminum mixed powders

NASA Astrophysics Data System (ADS)

Maleque, M. A.; Abdullah, U.; Yaacob, I.; Ali, Y.

2016-04-01

Currently, carbon nanotube (CNT) is attracting much interest as fibrous materials for reinforcing aluminum matrix composites due to unique properties, such as high strength, elastic modulus, flexibility and high aspect ratios. However, the quality of the dispersion is the major concerning factor which determines the homogeneity of the enhanced mechanical and tribological properties of the composite. This work study and characterized carbon nanotube dispersion in ballmilled CNT-aluminum mixed powders with four different formulations such as 1, 1.5, 2 and 2.5 wt% CNT under high energy planetary ball milling operations. The ball milling was performed for two hours at constant milling speed of 250 rpm under controlled atmosphere. The characterization is performed using FESEM and EDX analyzer for mapping, elemental and line analysis. The experimental results showed homogeneous dispersion of CNTs in aluminum matrix. The composite mixture showed similar pattern from mapping, elemental and line analysis. Identification of only two peaks proved that controlled atmosphere during milling prevented the formation of inter metallic compounds such as aluminum carbide in the composite mixture. Therefore, this CNT-A1 composite powder mixture can be used for new nano-composite development without any agglomeration problem.

Grinding as an approach to the production of high-strength, dispersion-strengthened nickel-base alloys

NASA Technical Reports Server (NTRS)

Orth, N. W.; Quatinetz, M.; Weeton, J. W.

1970-01-01

Mechanical process produces dispersion-strengthened metal alloys. Power surface contamination during milling is removed by a cleaning method that involves heating thin shapes or partially-compacted milled powder blends in hydrogen to carefully controlled temperature schedules.

DESIGN CONSIDERATIONS FOR PULP AND PAPER-MILL SLUDGE LANDFILLS

EPA Science Inventory

This report presents procedures for the engineering design and control of pulp and paper-mill sludge disposal landfills. Engineering design will allow more efficient use, thereby contributing to economic and environmental benefits. To form the basis for engineering design of slud...

Milling induced amorphisation and recrystallization of α-lactose monohydrate.

PubMed

Badal Tejedor, Maria; Pazesh, Samaneh; Nordgren, Niklas; Schuleit, Michael; Rutland, Mark W; Alderborn, Göran; Millqvist-Fureby, Anna

2018-02-15

Preprocessing of pharmaceutical powders is a common procedure to condition the materials for a better manufacturing performance. However, such operations may induce undesired material properties modifications when conditioning particle size through milling, for example. Modification of both surface and bulk material structure will change the material properties, thus affecting the processability of the powder. Hence it is essential to control the material transformations that occur during milling. Topographical and mechanical changes in surface properties can be a preliminary indication of further material transformations. Therefore a surface evaluation of the α-lactose monohydrate after short and prolonged milling times has been performed. Unprocessed α-lactose monohydrate and spray dried lactose were evaluated in parallel to the milled samples as reference examples of the crystalline and amorphous lactose structure. Morphological differences between unprocessed α-lactose, 1 h and 20 h milled lactose and spray dried lactose were detected from SEM and AFM images. Additionally, AFM was used to simultaneously characterize particle surface amorphicity by measuring energy dissipation. Extensive surface amorphicity was detected after 1 h of milling while prolonged milling times showed only a moderate particle surface amorphisation. Bulk material characterization performed with DSC indicated a partial amorphicity for the 1 h milled lactose and a fully amorphous thermal profile for the 20 h milled lactose. The temperature profiles however, were shifted somewhat in the comparison to the amorphous reference, particularly after extended milling, suggesting a different amorphous state compared to the spray-dried material. Water loss during milling was measured with TGA, showing lower water content for the lactose amorphized through milling compared to spray dried amorphous lactose. The combined results suggest a surface-bulk propagation of the amorphicity during milling in combination with a different amorphous structural conformation to that of the amorphous spray dried lactose. The hardened surface may be due to either surface crystallization of lactose or to formation of a low-water glass transition. Copyright © 2017 Elsevier B.V. All rights reserved.

Application of variable teeth pitch face mill as chatter suppression method for non-rigid technological system

NASA Astrophysics Data System (ADS)

Svinin, V. M.; Savilov, A. V.

2018-03-01

The article describes the results of experimental studies on the effects of variation type for variable teeth pitches on low-rigidity workpiece chatter suppression efficiency in a feed direction and in a direction of the normal to the machined surface. Mill operation performance was identified by comparing the amplitudes of dominant chatter harmonics using constant and variable teeth pitches. The following variable pitch formation variants were studied: alternative, linear rising, and linear rising falling. The angle difference of adjacent teeth pitches ranged from 0 to 10°, from 5 to 8° and from 5 to 10° with interval of 1°. The experiments showed that for all variants, machining dynamics performance resulted from the difference of adjacent pitches corresponding to a half the chatter wavelength along the cutting surface. The alternative nature of a variable teeth pitch is most efficient as it almost completely suppresses the chatters. Theoretical explanations of the results are presented

Use of dry-milling derived thin stillage for producing eicosapentaenoic acid (EPA) by the fungus Pythium irregulare.

PubMed

Liang, Yi; Zhao, Xuefei; Strait, Megan; Wen, Zhiyou

2012-05-01

This study was to explore the use of thin stillage, a major byproduct in dry milling corn-ethanol plants, for production of eicosapentaenoic acid (EPA) by the fungus Pythium irregulare. Thin stillage contains various compounds that were ideal for fungal growth. Thin stillage concentration and temperature played important roles in fungal growth and EPA production. When 50% thin stillage was used in a stepwise temperature shift culture process, the cell density reached 23 g/L at day 9 with EPA yield and productivity of 243 and 27 mg/L day, respectively. The fungal biomass contained 39% lipid, 28% protein, 30% carbohydrate, and 3% ash. The fungal culture also generated a nutrient-depleted liquid by removing organic compounds in the raw thin stillage. The results collectively showed a new use of thin stillage by feeding to the fungus P. irregulare for producing omega-3 fatty acids. Copyright © 2012 Elsevier Ltd. All rights reserved.

Impact of cogongrass management strategies on generalist predators in cogongrass-infested longleaf pine plantations.

PubMed

Sells, Sallie M; Held, David W; Enloe, Stephen F; Loewenstein, Nancy J; Eckhardt, Lori G

2015-03-01

Cogongrass (Imperata cylindrica Beav.) is an aggressive, invasive weed with a global distribution. In North America, it threatens the integrity of southeastern pine agroecosystems, including longleaf pine (Pinus palustris Mill.). While studies have examined the impacts of cogongrass and various vegetation management strategies on longleaf pine understory plant communities, little is known about how they impact associated insect communities. To understand the effect of cogongrass management strategies on arthropod natural enemies and bark beetles, a split-plot design was used to test fire (whole-plot) and four subplot treatments (control, herbicide, seeding and herbicide plus seeding). Arthropods were sampled using pitfall traps and sweep samples. After 2 years of sampling, total natural enemies were not significantly affected by subplot treatment but were affected by burn treatment. Upon subdividing natural enemies into groups, only spiders were significantly affected by subplot treatment, but predatory beetles and ants were significantly affected by burn treatment. The abundance of root-feeding bark beetles (Hylastes spp.) was not significant by subplot or whole-plot treatments. Multiple applications of herbicide remain the most effective way to manage cogongrass in longleaf pine. In this study, we found limited evidence that cogongrass management with herbicides would negatively impact arthropod natural enemies associated with longleaf pine or locally increase root-feeding bark beetles. © 2014 Society of Chemical Industry.

PBB episode in Michigan: an overall appraisal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fries, G.F.

1985-01-01

Polybrominated biphenyls (PBB) were used as a fire retardant. In common with other halogenated hydrocarbons, PBBs are lipophilic and resistant to chemical and metabolic degradation. Cattle on about 25 Michigan farms were exposed to as much as 250 g per head of PBB when it was accidentally mixed in cattle feed in 1973 to 1974. Livestock exposures several orders of magnitude lower occurred on several hundred other farms because of carryover and equipment contamination in feed mills. Approximately 85% of the Michigan population received some exposure to PBB because dairy product marketing involves mixing milk from many farms. A fewmore » cases of high human exposure, which may have been as great as 10 g, occurred when residents of the more highly exposed farms consumed their own products. Although numerous clinical signs and pathological changes were reported in exposed cattle, only anorexia, lacrimation, emaciation, hyperkeratosis, and kidney damage were confirmed in controlled studies. The acute toxicity of PBB in laboratory animals is low, but a variety of subacute effects have been reported. Induction of microsomal enzymes, enlargement and histopathological changes of the liver, fetotoxicity, and immunosuppression are among the more significant. Epidemiological studies of exposed humans have revealed no pattern of clinical signs or symptoms that were related to PBB exposure. A complete evaluation of the human consequences of exposure to PBB await the conclusion of long-term epidemiological studies. 84 references.« less

Design description of the Tangaye Village photovoltaic power system

NASA Astrophysics Data System (ADS)

Martz, J. E.; Ratajczak, A. F.

1982-06-01

The engineering design of a stand alone photovoltaic (PV) powered grain mill and water pump for the village of Tangaye, Upper Volta is described. The socioeconomic effects of reducing the time required by women in rural areas for drawing water and grinding grain were studied. The suitability of photovoltaic technology for use in rural areas by people of limited technical training was demonstrated. The PV system consists of a 1.8-kW (peak) solar cell array, 540 ampere hours of battery storage, instrumentation, automatic controls, and a data collection and storage system. The PV system is situated near an improved village well and supplies d.c. power to a grain mill and a water pump. The array is located in a fenced area and the mill, battery, instruments, controls, and data system are in a mill building. A water storage tank is located near the well. The system employs automatic controls which provide battery charge regulation and system over and under voltage protection. This report includes descriptions of the engineering design of the system and of the load that it serves; a discussion of PV array and battery sizing methodology; descriptions of the mechanical and electrical designs including the array, battery, controls, and instrumentation; and a discussion of the safety features. The system became operational on March 1, 1979.

Design description of the Tangaye Village photovoltaic power system

NASA Technical Reports Server (NTRS)

Martz, J. E.; Ratajczak, A. F.

1982-01-01

The engineering design of a stand alone photovoltaic (PV) powered grain mill and water pump for the village of Tangaye, Upper Volta is described. The socioeconomic effects of reducing the time required by women in rural areas for drawing water and grinding grain were studied. The suitability of photovoltaic technology for use in rural areas by people of limited technical training was demonstrated. The PV system consists of a 1.8-kW (peak) solar cell array, 540 ampere hours of battery storage, instrumentation, automatic controls, and a data collection and storage system. The PV system is situated near an improved village well and supplies d.c. power to a grain mill and a water pump. The array is located in a fenced area and the mill, battery, instruments, controls, and data system are in a mill building. A water storage tank is located near the well. The system employs automatic controls which provide battery charge regulation and system over and under voltage protection. This report includes descriptions of the engineering design of the system and of the load that it serves; a discussion of PV array and battery sizing methodology; descriptions of the mechanical and electrical designs including the array, battery, controls, and instrumentation; and a discussion of the safety features. The system became operational on March 1, 1979.

Milling of rice grains. The degradation on three structural levels of starch in rice flour can be independently controlled during grinding.

PubMed

Tran, Thuy T B; Shelat, Kinnari J; Tang, Daniel; Li, Enpeng; Gilbert, Robert G; Hasjim, Jovin

2011-04-27

Whole polished rice grains were ground using cryogenic and hammer milling to understand the mechanisms of degradation of starch granule structure, whole (branched) molecular structure, and individual branches of the molecules during particle size reduction (grinding). Hammer milling caused greater degradation to starch granules than cryogenic milling when the grains were ground to a similar volume-median diameter. Molecular degradation of starch was not evident in the cryogenically milled flours, but it was observed in the hammer-milled flours with preferential cleavage of longer (amylose) branches. This can be attributed to the increased grain brittleness and fracturability at cryogenic temperatures, reducing the mechanical energy required to diminish the grain size and thus reducing the probability of chain scission. The results indicate, for the first time, that branching, whole molecule, and granule structures of starch can be independently altered by varying grinding conditions, such as grinding force and temperature.

Nano-sized crystalline drug production by milling technology.

PubMed

Moribe, Kunikazu; Ueda, Keisuke; Limwikrant, Waree; Higashi, Kenjirou; Yamamoto, Keiji

2013-01-01

Nano-formulation of poorly water-soluble drugs has been developed to enhance drug dissolution. In this review, we introduce nano-milling technology described in recently published papers. Factors affecting the size of drug crystals are compared based on the preparation methods and drug and excipient types. A top-down approach using the comminution process is a method conventionally used to prepare crystalline drug nanoparticles. Wet milling using media is well studied and several wet-milled drug formulations are now on the market. Several trials on drug nanosuspension preparation using different apparatuses, materials, and conditions have been reported. Wet milling using a high-pressure homogenizer is another alternative to preparing production-scale drug nanosuspensions. Dry milling is a simple method of preparing a solid-state drug nano-formulation. The effect of size on the dissolution of a drug from nanoparticles is an area of fundamental research, but it is sometimes incorrectly evaluated. Here, we discuss evaluation procedures and the associated problems. Lastly, the importance of quality control, process optimization, and physicochemical characterization are briefly discussed.

Understanding Longitudinal Wood Fiber Ultra-structure for Producing Cellulose Nanofibrils Using Disk Milling with Diluted Acid Prehydrolysis

NASA Astrophysics Data System (ADS)

Qin, Yanlin; Qiu, Xueqing; Zhu, J. Y.

2016-10-01

Here we used dilute oxalic acid to pretreat a kraft bleached Eucalyptus pulp (BEP) fibers to facilitate mechanical fibrillation in producing cellulose nanofibrils using disk milling with substantial mechanical energy savings. We successfully applied a reaction kinetics based combined hydrolysis factor (CHFX) as a severity factor to quantitatively control xylan dissolution and BEP fibril deploymerization. More importantly, we were able to accurately predict the degree of polymerization (DP) of disk-milled fibrils using CHFX and milling time or milling energy consumption. Experimentally determined ratio of fibril DP and number mean fibril height (diameter d), DP/d, an aspect ratio measurer, were independent of the processing conditions. Therefore, we hypothesize that cellulose have a longitudinal hierarchical structure as in the lateral direction. Acid hydrolysis and milling did not substantially cut the “natural” chain length of cellulose fibrils. This cellulose longitudinal hierarchical model provides support for using weak acid hydrolysis in the production of cellulose nanofibrils with substantially reduced energy input without negatively affecting fibril mechanical strength.

17. INTERIOR VIEW, BASEMENT, LOOKING SOUTHWEST AT THE GEAR PIT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. INTERIOR VIEW, BASEMENT, LOOKING SOUTHWEST AT THE GEAR PIT BELOW THE GRINDING STONES, SHOWING WOODEN COGS ATTACHED TO UNDERGROUND TURBINES. FRICTION DRIVE VISIBLE BEHIND CONTROL BAR (LEFT) WHICH OPERATES SMUT MILL - Schech's Mill, Beaver Creek State Park, La Crescent, Houston County, MN

Vertical marginal gap evaluation of conventional cast and computer numeric controlled-milled titanium full-arch implant-supported frameworks.

PubMed

Alfadda, Sara A

2014-01-01

To use a novel approach to measure the amount of vertical marginal gap in computer numeric controlled (CNC)-milled titanium frameworks and conventional cast frameworks. Ten cast frameworks were fabricated on the mandibular master casts of 10 patients. Then, 10 CNC-milled titanium frameworks were fabricated by laser scanning the cast frameworks. The vertical marginal gap was measured and analyzed using the Contura-G2 coordinate measuring machine and special computer software. The CNC-milled titanium frameworks showed an overall reduced mean vertical gap compared with the cast frameworks in all five analogs. This difference was highly statistically significant in the distal analogs. The largest mean gap in the cast framework was recorded in the most distal analogs, and the least amount was in the middle analog. Neither of the two types of frameworks provided a completely gap-free superstructure. The CNCmilled titanium frameworks showed a significantly smaller vertical marginal gap than the cast frameworks.

Dose response effect of cement dust on respiratory muscles competence in cement mill workers.

PubMed

Meo, Sultan A; Azeem, Muhammad A; Qureshi, Aijaz A; Ghori, G Moinudin; Al-Drees, Abdul Majeed; Feisal Subhan, Mirza Muhammad

2006-12-01

Electromyography (EMG) of respiratory muscles is a reliable method of assessing the ventilatory muscle function, but still its use has not been fully utilized to determine the occupational and environmental hazards on respiratory muscles. Therefore, EMG of intercostal muscles was performed to determine the dose response effect of cement dust on respiratory muscles competence. Matched cross-sectional study of EMG in 50 non-smoking cement mill workers with an age range of 20 - 60 years, who worked without the benefit of cement dust control ventilation or respiratory protective devices. EMG was performed by using surface electrodes and chart recorder. Significant reduction was observed in number of peaks (p < 0.0005), maximum peak amplitude (p < 0.0005), peak-to-peak amplitude (p < 0.0005) and duration of response (p < 0.0005) in cement mill workers compared to their matched control. Cement dust impairs the intercostal muscle competence and stratification of results shows a dose-effect of years of exposure in cement mill.

Sub-nanometer milling of layered materials by a focused Helium Ion Beam

NASA Astrophysics Data System (ADS)

Zhang, Hongzhou; Fox, Daniel; Zhou, Yangbo; O'Connell, Robert

2014-03-01

The modification of the structure and geometry of materials at the nanoscale can be used to tailor their properties. A controllable process which can achieve this is required for the development of next generation nano-devices. We used the highly focused beam of helium ions in a helium ion microscope (HIM) to fabricate nanostructures within various layered materials such as graphene, MoS2, TiO2 and Mn2O3. Arbitrary patterns can be defined in order to produce structures such as nanoribbons. The edge configuration of atoms in such structures plays a large role in defining their properties. High resolution transmission electron microscopy (TEM) and scanning-TEM (STEM) were used to analyse the structure of the materials after milling. The direct milling of the materials by the helium ions means this approach is suitable for a wide range of nanomaterials. Complex structures can be realized via sophisticated beam control. This also results in the ability to mill along different directions in a crystal, producing edges with different configurations.

Vermicomposting of sugar industry waste (press mud) mixed with cow dung employing an epigeic earthworm Eisenia fetida.

PubMed

Sangwan, P; Kaushik, C P; Garg, V K

2010-01-01

In India, millions of tons of press mud (PM) are generated by sugar mills every year. This paper reports the potential of vermitechnology to convert sugar industry waste PM mixed with cow dung (CD) into vermicompost, employing an epigeic earthworm Eisenia fetida. A total of six different reactors were established having different ratios of PM and CD including one control (CD only). The growth and fecundity of E. fetida was monitored for 13 weeks. Maximum growth was recorded in 100% CD, but earthworms grew and reproduced favourably up to 1:1 PM and CD feed composition. However, greater percentages of PM in different reactors significantly affected the growth and fecundity of worms. Vermicomposting resulted in a decrease in carbon concentration and an increase in nitrogen, phosphorus and calcium concentrations of the vermicompost. Investigations indicated that vermicomposting could be an alternative technology for the management of PM into useful fertilizing material, if mixed at maximum 50% with CD.

Influencing Factors and Workpiece's Microstructure in Laser-Assisted Milling of Titanium

NASA Astrophysics Data System (ADS)

Wiedenmann, R.; Liebl, S.; Zaeh, M. F.

Today's lightweight components have to withstand increasing mechanical and thermal loads. Therefore, advanced materials substitute conventional materials like steel or aluminum alloys. Using these high-performance materials the associated costs become prohibitively high. This paper presents the newest fundamental investigations on the hybrid process 'laser-assisted milling' which is an innovative technique to process such materials. The focus is on the validation of a numerical database for a CAD/CAM process control unit which is calculated by using simulation. Prior to that, the influencing factors on a laser-assisted milling process are systematically investigated using Design of Experiments (DoE) to identify the main influencing parameters coming from the laser and the milling operation.

Work-related symptoms and dose-response relationships for personal exposures and pulmonary function among woodworkers.

PubMed

Mandryk, J; Alwis, K U; Hocking, A D

1999-05-01

Four sawmills, a wood chipping mill, and five joineries in New South Wales, Australia, were studied for the effects of personal exposure to wood dust, endotoxins. (1-->3)-beta-D-glucans, Gram-negative bacteria, and fungi on lung function among woodworkers. Personal inhalable and respirable dust sampling was carried out. The lung function tests of workers were conducted before and after a workshift. The mean percentage cross-shift decrease in lung function was markedly high for woodworkers compared with the controls. Dose-response relationships among personal exposures and percentage cross-shift decrease in lung function and percentage predicted lung function were more pronounced among joinery workers compared with sawmill and chip mill workers. Woodworkers had markedly high prevalence of regular cough, phlegm, and chronic bronchitis compared with controls. Significant associations were found between percentage cross-shift decrease in FVC and regular phlegm and blocked nose among sawmill and chip mill workers. Both joinery workers and sawmill and chip mill workers showed significant relationships between percentage predicted lung function (FVC, FEV1, FEV1/FVC, FEF25-75%) and respiratory symptoms. Wood dust and biohazards associated with wood dust are potential health hazards and should be controlled.

Direct heat geothermal opportunities at Pahoa, Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moreau, J.; Jones, W.L.

1980-09-01

A geothermal commercial park located near Pahoa, Hawaii, has been found to be technically feasible. However, community acceptance varies from optimistic support for the job opportunities to only lukewarm acceptance by most residents of the nearby planned residential community. Interviews, team evaluations, and calculations of energy and transportation savings were used to reduce a list of candidate processes to four. These four include an ethanol plant, a cattle feed mill, a protein recovery plant, and a papaya processing facility. In addition, a research laboratory is planned for the evaluation of other processes identified as very promising.

Allergic contact dermatitis from a paper mill slimicide containing 2-bromo-4'-hydroxyacetophenone.

PubMed

Jensen, Charlotte D; Andersen, Klaus E

2003-03-01

Slimicides are biocidal products used in paper mills to inhibit the proliferation of slime-forming microorganisms that would otherwise spoil the paper products. A laboratory technician working at a paper mill had recurring dermatitis related to contact with the slimicide Busan 1130. We report the first case of allergic contact dermatitis from the slimicide Busan 1130. Diagnostic patch testing was performed with solutions of Busan 1130 and its active ingredient, 2-bromo-4'-hydroxyacetophenone (BHAP). Twenty-five controls were also tested. The patient showed a ++ reaction to 0.1% Busan 1130 aqueous solution and 0.01% BHAP in ethanol. All controls were negative. The patient had recurrent allergic contact dermatitis from exposure to BHAP contained in the slimicide Busan 1130.

Factors affecting the flight capacity of Tetrastichus planipennisi (Hymenoptera: Eulophidae), a classical biological control agent of Agrilus planipennis (Coleoptera: Buprestidae).

PubMed

Fahrner, Samuel J; Lelito, Jonathan P; Blaedow, Karen; Heimpel, George E; Aukema, Brian H

2014-12-01

The dispersal characteristics of a biological control agent can have direct implications on the ability of that agent to control populations of a target host. Tetrastichus planipennisi Yang (Hymenoptera: Eulophidae) is a parasitic wasp native to eastern Asia that has been introduced into the United States as part of a classical biological control program against the emerald ash borer Agrilus planipennis Fairmaire (Coleoptera: Buprestidae). We used computer-monitored flight mills to investigate the role of age, feeding status, mating status, and size on the flight capacity of female T. planipennisi over a 24-h period. We also compared flight capacity between sexes. Flight distance of female T. planipennisi representative of populations released in the biological control program averaged 1.26 km in 24 h with a maximum flight of just over 7 km. Median flight distance, however, was 422 m. The flight capacity of females fed a honey-water solution was 41× that of females provided only water, who flew very little. Larger females were capable of flying farther distances, but age did not affect the flight capacity of females up to 70 d posteclosion. Females dispersed 6× farther than did their smaller, male counterparts. The implications of our findings to host-parasitoid interactions and release protocols for distributing T. planipennisi are discussed.

An outbreak of Salmonella Typhimurium phage type 42 associated with the consumption of raw flour.

PubMed

McCallum, Lisa; Paine, Shevaun; Sexton, Kerry; Dufour, Muriel; Dyet, Kristin; Wilson, Maurice; Campbell, Donald; Bandaranayake, Don; Hope, Virginia

2013-02-01

A cluster of salmonellosis cases caused by Salmonella Typhimurium phage type 42 (STM42) emerged in New Zealand in October 2008. STM42 isolates from a wheat-based poultry feed raw material (broll; i.e., product containing wheat flour and particles of grain) had been identified in the 2 months prior to this cluster. Initial investigations indicated that eating uncooked baking mixture was associated with illness. A case-control study was conducted to test the hypothesis that there was an association between STM42 cases and consumption of raw flour or other baking ingredients. Salmonella isolates from human and non-human sources were compared using pulsed-field gel electrophoresis (PFGE) and multiple-locus variable number tandem repeat analysis (MLVA). Environmental investigations included testing flour and other baking ingredients from case homes, unopened bags of flour purchased from retail stores, and inspection of an implicated flour mill. A case-control study of 39 cases and 66 controls found cases had 4.5 times the odds of consuming uncooked baking mixture as controls (95% confidence interval [CI] 1.6-12.5, p-value 0.001). Examination of individual baking ingredients found that, after adjusting for eggs, flour had an odds ratio (OR) of 5.7 (95% CI 1.1-29.1, p-value 0.035). After adjusting for flour, eggs had an OR of 0.8 (95% CI 0.2-3.4, p-value 0.762). PFGE patterns were identical for all STM42 isolates tested; however, MLVA distinguished isolates that were epidemiologically linked to the cluster. STM42 was recovered from flour taken from four cases' homes, two unopened packs purchased from retail stores and packs from three batches of retrieved (recalled) product. This outbreak was associated with the consumption of uncooked baking mixture containing flour contaminated with STM42. The implicated flour mill initiated a voluntary withdrawal from sale of all batches of flour thought to be contaminated. Media releases informed the public about implicated flour brands and the risks of consuming uncooked baking mixture.

Surface hardening of Al alloys through controlled ball-milling and sintering.

PubMed

Kim, Seek Hyeoun; Kim, Yong Jin; Ahn, Jung-Ho

2012-07-01

One of the drawbacks of aluminum and its alloys is the lack of proper heat-treatment for surface-hardening. In the present work, a new and simple method of hardening the surface of aluminum and its alloys was developed. Low-energy ball-milling using specific process control agents (PCAs) was employed, using subsequent sintering in a controlled atmosphere. The PCAs in the present work were very effective both for milling and the formation of hard nanocrystalline dispersoids during sintering. The residual oxygen in a sintering atmosphere also played an important role in the formation of AIN or Al-O-N dispersoids. Through the proper control of the processing atmosphere and PCAs, the hardness and thickness of the hardened layers could be adjusted. The results of the wear test showed that the present aluminum alloys can be effectively utilized as light-weight components with a good wear resistance. Furthermore, the present method involves a simple forming process of die-compaction and sintering.

Biofuel manufacturing from woody biomass: effects of sieve size used in biomass size reduction.

PubMed

Zhang, Meng; Song, Xiaoxu; Deines, T W; Pei, Z J; Wang, Donghai

2012-01-01

Size reduction is the first step for manufacturing biofuels from woody biomass. It is usually performed using milling machines and the particle size is controlled by the size of the sieve installed on a milling machine. There are reported studies about the effects of sieve size on energy consumption in milling of woody biomass. These studies show that energy consumption increased dramatically as sieve size became smaller. However, in these studies, the sugar yield (proportional to biofuel yield) in hydrolysis of the milled woody biomass was not measured. The lack of comprehensive studies about the effects of sieve size on energy consumption in biomass milling and sugar yield in hydrolysis process makes it difficult to decide which sieve size should be selected in order to minimize the energy consumption in size reduction and maximize the sugar yield in hydrolysis. The purpose of this paper is to fill this gap in the literature. In this paper, knife milling of poplar wood was conducted using sieves of three sizes (1, 2, and 4 mm). Results show that, as sieve size increased, energy consumption in knife milling decreased and sugar yield in hydrolysis increased in the tested range of particle sizes.

Milling assisted synthesis of calcium zirconate СаZrО3

NASA Astrophysics Data System (ADS)

Kalinkin, A. M.; Nevedomskii, V. N.; Kalinkina, E. V.; Balyakin, K. V.

2014-08-01

Monophase calcium zirconate (CaZrO3) has been prepared from the equimolar ZrO2 + CaCO3 mixture by two-step synthesis process. In the first step, mechanical treatment of the mixture is performed in an AGO-2 planetary ball mill. In the second step, the milled mixture is annealed to form calcium zirconate. High-energy ball milling of the (ZrO2+CaCO3) mixture results in decrease in the temperature of CaZrO3 formation during annealing at 950 °C. The enhancement of CaZrO3 synthesis is due to accumulation of excess energy by the reagents, decreasing the particle size and notable increase in the interphase area because of “smearing” of CaCO3 on ZrO2 particles during milling. Nanocrystalline calcium zirconate has been produced by controlling the annealing temperature and time.

Ethanol production, corn gluten feed, and EC trade. Agriculture information bulletin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, M.

1993-07-01

The profitability of ethanol depends not only on sales of ethanol, but on sales of several coproducts of corn wet-milling such as corn gluten feed (CGF). CGF demand and supply are affected by several European Community (EC) and US policies, such as EC grain price supports and US energy policies. Changes in existing policies and programs could have a significant effect on the CGF market and, consequently, on the profitability of ethanol production. The report examines the implications of several policy options on demand, supply, and price of CGF and on the profitability of ethanol production. The policy changes examinedmore » include: (1) the effect of proposed changes in EC farm and trade policies, and (2) the effect of increased ethanol production due to proposed US environmental policies, such as the reauthorization of the Clean Air Act.« less

Contamination risk of stable isotope samples during milling.

PubMed

Isaac-Renton, M; Schneider, L; Treydte, K

2016-07-15

Isotope analysis of wood is an important tool in dendrochronology and ecophysiology. Prior to mass spectrometry analysis, wood must be homogenized, and a convenient method involves a ball mill capable of milling samples directly in sample tubes. However, sample-tube plastic can contaminate wood during milling, which could lead to biological misinterpretations. We tested possible contamination of whole wood and cellulose samples during ball-mill homogenization for carbon and oxygen isotope measurements. We used a multi-factorial design with two/three steel milling balls, two sample amounts (10 mg, 40 mg), and two milling times (5 min, 10 min). We further analyzed abrasion by milling empty tubes, and measured the isotope ratios of pure contaminants. A strong risk exists for carbon isotope bias through plastic contamination: the δ(13) C value of polypropylene deviated from the control by -6.77‰. Small fibers from PTFE filter bags used during cellulose extraction also present a risk as the δ(13) C value of this plastic deviated by -5.02‰. Low sample amounts (10 mg) showed highest contamination due to increased abrasion during milling (-1.34‰), which is further concentrated by cellulose extraction (-3.38‰). Oxygen isotope measurements were unaffected. A ball mill can be used to homogenize samples within test tubes prior to oxygen isotope analysis, but not prior to carbon or radiocarbon isotope analysis. There is still a need for a fast, simple and contamination-free sample preparation procedure. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

40 CFR 62.2350 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) emissions from existing kraft pulp mills and tall oil plants (both new and existing) submitted on May 24... is June 1, 1990. (5) Control of metals, acid gases, organic compounds and nitrogen oxide emissions... existing facilities in the following categories of sources: (1) Sulfuric acid plants. (2) Kraft pulp mills...

40 CFR 62.2350 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) emissions from existing kraft pulp mills and tall oil plants (both new and existing) submitted on May 24... is June 1, 1990. (5) Control of metals, acid gases, organic compounds and nitrogen oxide emissions... existing facilities in the following categories of sources: (1) Sulfuric acid plants. (2) Kraft pulp mills...

40 CFR 62.2350 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) emissions from existing kraft pulp mills and tall oil plants (both new and existing) submitted on May 24... is June 1, 1990. (5) Control of metals, acid gases, organic compounds and nitrogen oxide emissions... existing facilities in the following categories of sources: (1) Sulfuric acid plants. (2) Kraft pulp mills...

40 CFR 62.2350 - Identification of plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) emissions from existing kraft pulp mills and tall oil plants (both new and existing) submitted on May 24... is June 1, 1990. (5) Control of metals, acid gases, organic compounds and nitrogen oxide emissions... existing facilities in the following categories of sources: (1) Sulfuric acid plants. (2) Kraft pulp mills...

Effect of grinding intensity and pelleting of the diet on indoor particulate matter concentrations and growth performance of weanling pigs.

PubMed

Ulens, T; Demeyer, P; Ampe, B; Van Langenhove, H; Millet, S

2015-02-01

This study evaluated the effect of feed form and grinding intensity of the pig diet and the interaction between both on the particulate matter (PM) concentrations inside a pig nursery and the growth performances of weanling pigs. Four diets were compared: finely ground meal, coarsely ground meal, finely ground pellets, and coarsely ground pellets. Four weaning rounds with 144 pigs per weaning round, divided over 4 identical compartments, were monitored. Within each weaning round, each compartment was randomly assigned to 1 of 4 treatments. A hammer mill with a screen of 1.5 or 6 mm was used to grind the ingredients of the finely ground and coarsely ground feeds, respectively. Indoor concentrations of the following PM fractions were measured: PM that passes through a size-selective inlet with a 50 % efficiency cutoff at 10 (PM10) , 2.5 (PM2.5), or 1 (PM1) μm aerodynamic diameter, respectively (USEPA, 2004). Feeding pelleted diets instead of meal diets gave rise to higher PM10 (P < 0.001), PM2.5 (P < 0.001), and PM1 (P < 0.001) concentrations. Grinding intensity had an effect only on PM10 (P < 0.05) concentrations. No interaction between feed form and grinding intensity was found for any of the PM fractions. Interactions (P < 0.05) between feed form and grinding intensity on ADFI and ADG were found. Grinding intensity had an effect only on the meal diets with higher ADFI for the coarsely ground meal. Pigs fed the finely ground meal had a lower (P < 0.001) ADG than the other 3 diets. Feed efficiency was influenced only by the feed form (P < 0.001) and not by the grinding intensity. Pelleting the feed gave rise to a higher G:F. In conclusion, a contradiction between environmental concerns and performance results was found. Feeding pelleted diets to the piglets improved growth performance but also increased indoor PM concentrations.

BLENDING LOW ENRICHED URANIUM WITH DEPLETED URANIUM TO CREATE A SOURCE MATERIAL ORE THAT CAN BE PROCESSED FOR THE RECOVERY OF YELLOWCAKE AT A CONVENTIONAL URANIUM MILL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schutt, Stephen M.; Hochstein, Ron F.; Frydenlund, David C.

2003-02-27

Throughout the United States Department of Energy (DOE) complex, there are a number of streams of low enriched uranium (LEU) that contain various trace contaminants. These surplus nuclear materials require processing in order to meet commercial fuel cycle specifications. To date, they have not been designated as waste for disposal at the DOE's Nevada Test Site (NTS). Currently, with no commercial outlet available, the DOE is evaluating treatment and disposal as the ultimate disposition path for these materials. This paper will describe an innovative program that will provide a solution to DOE that will allow disposition of these materials atmore » a cost that will be competitive with treatment and disposal at the NTS, while at the same time recycling the material to recover a valuable energy resource (yellowcake) for reintroduction into the commercial nuclear fuel cycle. International Uranium (USA) Corporation (IUSA) and Nuclear Fuel Services, Inc. (NFS) have entered into a commercial relationship to pursue the development of this program. The program involves the design of a process and construction of a plant at NFS' site in Erwin, Tennessee, for the blending of contaminated LEU with depleted uranium (DU) to produce a uranium source material ore (USM Ore{trademark}). The USM Ore{trademark} will then be further processed at IUC's White Mesa Mill, located near Blanding, Utah, to produce conventional yellowcake, which can be delivered to conversion facilities, in the same manner as yellowcake that is produced from natural ores or other alternate feed materials. The primary source of feed for the business will be the significant sources of trace contaminated materials within the DOE complex. NFS has developed a dry blending process (DRYSM Process) to blend the surplus LEU material with DU at its Part 70 licensed facility, to produce USM Ore{trademark} with a U235 content within the range of U235 concentrations for source material. By reducing the U235 content to source material levels in this manner, the material will be suitable for processing at a conventional uranium mill under its existing Part 40 license to remove contaminants and enable the product to re-enter the commercial fuel cycle. The tailings from processing the USM Ore{trademark} at the mill will be permanently disposed of in the mill's tailings impoundment as 11e.(2) byproduct material. Blending LEU with DU to make a uranium source material ore that can be returned to the nuclear fuel cycle for processing to produce yellowcake, has never been accomplished before. This program will allow DOE to disposition its surplus LEU and DU in a cost effective manner, and at the same time provide for the recovery of valuable energy resources that would be lost through processing and disposal of the materials. This paper will discuss the nature of the surplus LEU and DU materials, the manner in which the LEU will be blended with DU to form a uranium source material ore, and the legal means by which this blending can be accomplished at a facility licensed under 10 CFR Part 70 to produce ore that can be processed at a conventional uranium mill licensed under 10 CFR Part 40.« less

Preparation of autogenous bone grafts in two different bone mills.

PubMed

Erpenstein, H; Diedrich, P; Borchard, R

2001-12-01

The purpose of this study was to evaluate the performance of two bone mills (R Quetin Bone Mill and Micro Knochenmühle, Aesculap) for the grinding of autogenous bone (intraoral, cortical) according to the following criteria: (1) loss of bone during the grinding process, (2) particle size of the chips, (3) variability in chip size, (4) technical handling, and (5) cost-benefit ratio. The amount of material loss was determined by harvesting 30 bone cores from the mandibular symphysis of a pig. Each specimen was weighed before and after the grinding procedure on scales with an accuracy of 0.1 mg. The size and variability of the bone particles were determined histomorphometrically. Twenty-seven bone specimens from different patients were analyzed. Eight were ground with the Aesculap and 12 with the Quetin mill. Seven specimens harvested with a Brånemark implant bur served as controls. A histologic section was prepared from each specimen, and 10 bone particles per section were subjected to histomorphometric analysis. The Quetin mill was superior in all points to the Aesculap mill for the requirements of a periodontal practice.

Understanding dental CAD/CAM for restorations--dental milling machines from a mechanical engineering viewpoint. Part B: labside milling machines.

PubMed

Lebon, Nicolas; Tapie, Laurent; Duret, Francois; Attal, Jean-Pierre

2016-01-01

Nowadays, dental numerical controlled (NC) milling machines are available for dental laboratories (labside solution) and dental production centers. This article provides a mechanical engineering approach to NC milling machines to help dental technicians understand the involvement of technology in digital dentistry practice. The technical and economic criteria are described for four labside and two production center dental NC milling machines available on the market. The technical criteria are focused on the capacities of the embedded technologies of milling machines to mill prosthetic materials and various restoration shapes. The economic criteria are focused on investment cost and interoperability with third-party software. The clinical relevance of the technology is discussed through the accuracy and integrity of the restoration. It can be asserted that dental production center milling machines offer a wider range of materials and types of restoration shapes than labside solutions, while labside solutions offer a wider range than chairside solutions. The accuracy and integrity of restorations may be improved as a function of the embedded technologies provided. However, the more complex the technical solutions available, the more skilled the user must be. Investment cost and interoperability with third-party software increase according to the quality of the embedded technologies implemented. Each private dental practice may decide which fabrication option to use depending on the scope of the practice.

Diet Replenishment for Ad-libitum–fed Mice Housed in Social Groups is Compatible with Shelf Life

PubMed Central

Huerkamp, Michael J; Dowdy, Minida R

2008-01-01

Regulatory guidelines and best practices in the care of research animals allow diets milled for laboratory animals to be used within 180 d of formulation but otherwise permit latitude and professional judgment in how and when feed is offered. As such, practices at some research institutions allow for the replenishment (‘topping up’) of fresh chow over that existing in the cage food hopper, rather than complete replacement of the diet on a regular basis. To determine the depletion rate of a pelleted diet as fed from a conventional overhead food hopper, the consumption of full hoppers of food was measured for breeding pairs of mice in production and gender-specific groups of weanlings and juvenile mice kept in ventilated cages at 71.9 ± 0.2 °F (approximately 22.6 °C) and 40% ± 5% relative humidity. Breeding pairs of mice depleted 97% of a 250-g ration within 44 d of offering and consumed diet at a rate of 4.7 ± 0.5 g per mouse daily. Gender-grouped weanling and juvenile mice housed 5 to 6 per cage exhausted more than 99% of a 500-g ration of diet in 24 d and consumed chow at a rate of 3.4 ± 0.3 g per animal daily. These findings suggest that breeding pairs and groups of mice kept 5 to 6 per cage deplete feed at such a rate that diets can be fed by using replenishment provided diet is offered within 5 mo of the milling date. PMID:18459713

40 CFR 421.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... dried Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (b) Subpart C—Scrap Screening and Milling... per million pounds) of aluminum scrap screened and milled Lead .000 .000 Zinc .000 .000 Ammonia (as N... .000 Ammonia (as N) .000 .000 (d) Subpart C—Demagging Wet Air Pollution Control. PSNS Pollutant or...

40 CFR 421.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... dried Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (b) Subpart C—Scrap Screening and Milling... per million pounds) of aluminum scrap screened and milled Lead .000 .000 Zinc .000 .000 Ammonia (as N... .000 Ammonia (as N) .000 .000 (d) Subpart C—Demagging Wet Air Pollution Control. PSNS Pollutant or...

40 CFR 421.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... dried Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (b) Subpart C—Scrap Screening and Milling... per million pounds) of aluminum scrap screened and milled Lead .000 .000 Zinc .000 .000 Ammonia (as N... .000 Ammonia (as N) .000 .000 (d) Subpart C—Demagging Wet Air Pollution Control. PSNS Pollutant or...

40 CFR 421.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... dried Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (b) Subpart C—Scrap Screening and Milling... per million pounds) of aluminum scrap screened and milled Lead .000 .000 Zinc .000 .000 Ammonia (as N... .000 Ammonia (as N) .000 .000 (d) Subpart C—Demagging Wet Air Pollution Control. PSNS Pollutant or...

40 CFR 421.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... dried Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (b) Subpart C—Scrap Screening and Milling... per million pounds) of aluminum scrap screened and milled Lead .000 .000 Zinc .000 .000 Ammonia (as N... .000 Ammonia (as N) .000 .000 (d) Subpart C—Demagging Wet Air Pollution Control. PSNS Pollutant or...

Biology and biological control of Dalmatian and yellow toadflax

Treesearch

Sharlene E. Sing; Rosemarie De Clerck-Floate; Richard W. Hansen; Hal Pearce; Carol Bell Randall; Ivo Tosevski; Sarah M. Ward

2016-01-01

Dalmatian toadflax, Linaria dalmatica (L.) Mill., and yellow toadflax, Linaria vulgaris Mill., are exotic weeds of rangeland, grassland, forests, and cropland. Both Dalmatian and yellow toadflax are short-lived perennial forbs that are easily recognized by their yellow snapdragon- like flowers (Figure 1a, 1b). Both species propagate by seed and vegetatively...

Effect of shrinkage on isothermal drying behavior of 2-phase olive mill waste

USDA-ARS?s Scientific Manuscript database

The objective of this study was to determine the drying behavior of 2-phase olive mill waste (2POMW) under isothermal microwave-convection drying conditions. 2POMW samples were dried in a thin layer in a variable-power pilot microwave oven with impinging air, using a feedback controller to maintain...

Leaching behavior of U, Mn, Sr, and Pb from different particle-size fractions of uranium mill tailings.

PubMed

Liu, Bo; Peng, Tongjiang; Sun, Hongjuan

2017-06-01

Pollution by the release of heavy metals from tailings constitutes a potential threat to the environment. To characterize the processes governing the release of Mn, Sr, Pb, and U from the uranium mill tailings, a dynamic leaching test was applied for different size of uranium mill tailings samples. Inductively coupled plasma atomic emission spectroscopy (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS) were performed to determine the content of Mn, Sr, Pb, and U in the leachates. The release of mobile Mn, Sr, Pb, and U fraction was slow, being faster in the initial stage and then attained a near steady-state condition. The experimental results demonstrate that the release of Mn, Sr, Pb, and U from uranium mill tailings with different size fractions is controlled by a variety of mechanisms. Surface wash-off is the release mechanism for Mn. The main release mechanism of Sr and Pb is the dissolution in the initial leaching stage. For U, a mixed process of wash-off and diffusion is the controlling mechanism.

Toward intradermal vaccination: preparation of powder formulations by collapse freeze-drying.

PubMed

Etzl, Elsa E; Winter, Gerhard; Engert, Julia

2014-03-01

Intradermal powder immunization is an emerging technique in vaccine delivery. The purpose of this study was to generate powder particles for intradermal injection by freeze-drying and subsequent cryo-milling. Two different freeze-drying protocols were compared, a moderate freeze-drying cycle and an aggressive freeze-drying cycle, which induced a controlled collapse of the sugar matrix. Ovalbumin served as model antigen. The influence of collapse drying and cryo-milling on particle morphology and protein stability was investigated. Cryo-milling generated irregularly shaped particles of size 20-70 µm. The recovery of soluble monomer of ovalbumin was not changed during freeze-drying and after cryo-milling, or after 12 months of storage at 2-8 °C. A slight increase in higher molecular weight aggregates was found in formulations containing the polymer dextran after 12 months of storage at 50 °C. Light obscuration measurements showed an increase in cumulative particle counts after cryo-milling that did not further increase during storage at 2-8 °C for 12 months. The applicability of the cryo-milling process to other therapeutic proteins was shown using recombinant human granulocyte-colony stimulating factor. Collapse freeze-drying and subsequent cryo-milling allows the generation of particles suitable for intradermal powder injection.

AISI/DOE Advanced Process Control Program Vol. 3 of 6 Microstructure Engineering in Hot Strip Mills, Part 1 of 2: Integrated Mathematical Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.K. Brimacombe; I.V. Samarasekera; E.B. Hawbolt

1999-07-31

This report describes the work of developing an integrated model used to predict the thermal history, deformation, roll forces, microstructural evolution and mechanical properties of steel strip in a hot-strip mill. This achievement results from a joint research effort that is part of the American Iron and Steel Institute's (AIS) Advanced Process Control Program, a collaboration between the U.S. DOE and fifteen North American Steelmakers.

New pressure control method of mixed gas in a combined cycle power plant of a steel mill

NASA Astrophysics Data System (ADS)

Xie, Yudong; Wang, Yong

2017-08-01

The enterprise production concept is changing with the development of society. A steel mill requires a combined-cycle power plant, which consists of both a gas turbine and steam turbine. It can recycle energy from the gases that are emitted from coke ovens and blast furnaces during steel production. This plant can decrease the overall energy consumption of the steel mill and reduce pollution to our living environment. To develop a combined-cycle power plant, the pressure in the mixed-gas transmission system must be controlled in the range of 2.30-2.40 MPa. The particularity of the combined-cycle power plant poses a challenge to conventional controllers. In this paper, a composite control method based on the Smith predictor and cascade control was proposed for the pressure control of the mixed gases. This method has a concise structure and can be easily implemented in actual industrial fields. The experiment has been conducted to validate the proposed control method. The experiment illustrates that the proposed method can suppress various disturbances in the gas transmission control system and sustain the pressure of the gas at the desired level, which helps to avoid abnormal shutdowns in the combined-cycle power plant.

On Operating a Nanofiltration Membrane for Olive Mill Wastewater Purification at Sub- and Super-Boundary Conditions.

PubMed

Stoller, Marco; Ochando-Pulido, Javier Miguel; Field, Robert

2017-07-14

In the last decades, membrane processes have gained a significant share of the market for wastewater purification. Although the product (i.e., purified water) is not of high added value, these processes are feasible both technically and from an economic point of view, provided the flux is relatively high and that membrane fouling is strongly inhibited. By controlling membrane fouling, the membrane may work for years without service, thus dramatically reducing operating costs and the need for membrane substitution. There is tension between operating at high permeate fluxes, which enhances fouling but reduces capital costs, and operating at lower fluxes which increases capital costs. Operating batch membrane processes leads to increased difficulties, since the feed fed to the membrane changes as a function of the recovery value. This paper is concerned with the operation of such a process. Membrane process designers should therefore avoid membrane fouling by operating membranes away from the permeate flux point where severe fouling is triggered. The design and operation of membrane purification plants is a difficult task, and the precision to properly describe the evolution of the fouling phenomenon as a function of the operating conditions is a key to success. Many reported works have reported on the control of fouling by operating below the boundary flux. On the other hand, only a few works have successfully sought to exploit super-boundary operating conditions; most super-boundary operations are reported to have led to process failures. In this work, both sub- and super-boundary operating conditions for a batch nanofiltration membrane process used for olive mill wastewater treatment were investigated. A model to identify a priori the point of transition from a sub-boundary to a super-boundary operation during a batch operation was developed, and this will provide membrane designers with a helpful tool to carefully avoid process failures.

Controlled cooling technology for bar and rod mills -- Computer simulation and operational results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mauk, P.J.; Kruse, M.; Plociennik, U.

The Controlled Cooling Technology (CCT) developed by SMS to simulate the rolling process and automatic control of the water cooling sections is presented. The Controlled Rolling and Cooling Technology (CRCT) model is a key part of the CCT system. It is used to simulate temperature management for the rolling stock on the computer before the actual rolling process takes place. This makes it possible to dispense with extensive rolling tests in the early stages of project planning and to greatly reduce the extent of such tests prior to the start of commercial production in a rolling mill. The CRCT modelmore » has been in use at Von Moos Stahl Ag for three years. It demonstrates that, by targeted improvement of the set-up values in both the technology and the plant, it is possible to improve microstructure quality and achieve better geometrical parameters in the rolled products. Also, the results gained with the CCT system in practical operation at the Kia Steel Bar Mill, Kunsan, Korea, are presented.« less

Assessment of the Content of Fluorescent Tracer in Granular Feed Mixture.

PubMed

Matuszek, Dominika B; Wojtkiewicz, Krystian

2018-05-03

Background: This paper describes the use of fluorescence induced by UV radiation to evaluate the share of tracer in feed mixture. Methods: For the purpose of this study, three substances were used. They are as follows: Tinopal, Rhodamine B, and Uranine. Tracer in the form of maize or kardi was added to chicken feed before the mixing process. Grains used in the process were grinded in the mill sieve with a mesh size of 4 and 6 mm. The drawn samples of the mixture were illuminated with UV radiation to make grain tracer light, and then the photo was taken with a digital camera. The acquired images were analyzed with the use of a computer program running on the RGB color model, which was the way to obtain essential information about the percentage share of tracer. Results: It was observed that, in the case of kardi grains, the proposed method gives results significantly deviating from the verification method. Conclusions: Only the tests with the use of maize having an average particle diameter of 2.4 mm and tinted with the solution of Rhodamine B led to acceptable results (consensual with the predetermined verification level).

Industrial contributions of arsenic to the environment.

PubMed Central

Nelson, K W

1977-01-01

Arsenic is present in all copper, lead, and zinc sulfide ores and is carried along with those metals in the mining, milling and concentrating process. Separation, final concentration and refining of by-product arsenic as the trioxide is achieved at smelters. Arsenic is the essential consistent element of many compounds important and widely used in agriculture and wood preservation. Lesser amounts are used in metal alloys, glass-making, and feed additives. There is no significant recycling. Current levels of arsenic emissions to the atmosphere from smelters and power plants and ambient air concentrations are given as data of greatest environmental interest. PMID:908308

MILLS-REINCKE PHENOMENON AND TYPHOID CONTROL BY VACCINE

PubMed Central

McGee, Harold G.

1920-01-01

Assuming typhoid to be an index of conditions favoring other causes of death, this author calls attention to the likelihood that anti-typhoid vaccination, by attacking typhoid alone, really masks sanitary conditions and may permit unnecessary deaths. Complete eradication of typhoid through vaccination would not affect the three other deaths suggested by the Mills-Reincke hypothesis. PMID:18010339

Biology and biological control of Dalmatian and yellow toadflax

Treesearch

Linda M. Wilson; Sharlene E. Sing; Gary L. Piper; Richard W. Hansen; Rosemarie De Clerck-Floate; Daniel K. MacKinnon; Carol Bell Randall

2005-01-01

Dalmatian toadflax, Linaria dalmatica (L.) P. Mill. ssp. dalmatica (Fig. 1a), and yellow toadflax, Linaria vulgaris (L.) P. Mill. (Fig. 1b), are exotic [see Glossary] weeds of rangeland, forests and cropland. Although several species of weedy toadflax have been intentionally or accidentally introduced to North America, these two species are by far the most common and...

The automatic lumber planing mill

Treesearch

Peter Koch

1957-01-01

It is probable that a truly automatic planning operation could be devised if some of the variables commonly present in the mill-run lumber were eliminated and the remaining variables kept under close control. This paper will deal with the more general situation faced by mostl umber manufacturing plants. In other words, it will be assumed that the incoming lumber has...

Residual efficacy of pyrethrin+methoprene for control of Tribolium castaneum and Tribolium confusum in a commercial flour mill

USDA-ARS?s Scientific Manuscript database

Concrete arenas with and without flour were placed in open, obstructed, and hidden positions inside a commercial flour mill and exposed to a combination treatment of pyrethrin + methoprene. Bioassays were conducted 1, 3, 5, and 7 weeks after the arenas were treated by adding flour to those arenas th...

Nutritional recommendations of feedlot consulting nutritionists: The 2015 New Mexico State and Texas Tech University survey.

PubMed

Samuelson, K L; Hubbert, M E; Galyean, M L; Löest, C A

2016-06-01

The 2015 feedlot consulting nutritionist survey is a collaborative project between New Mexico State University and Texas Tech University that focuses on summarizing the professional practices of consulting feedlot nutritionists and updates a 2007 survey. Forty-nine consulting feedlot nutritionists were asked to participate, of which 24 completed the survey. The nutritionists surveyed service over 14,000,000 cattle annually and were representatives from individual consulting practices (54.2%), corporate cattle feeding companies (20.8%), corporate feed manufacturing companies (20.8%), or a combination of consulting practices (4.2%). The survey was completed using a web-based survey tool and contained 101 questions that were divided into sections regarding general information about the consulting practice; general cattle management; receiving cattle management, diet adaption; mixers, feed mills, and feeding management; grains and grain processing; grain by-product use; roughage use; information about supplements and microingredients; liquid feed use; nutrient formulation; feed additive use; and information used as a basis for nutritional recommendations. In most cases, the results of the current survey were similar to those reported for the 2007 survey, with a few notable exceptions such as shifts in cattle numbers and preferences for specific feedstuffs. The present study introduced a number of new questions not included in the 2007 survey that focused on management strategies used in the receiving period. Data from this survey provide insight into current nutritional and management practices of consulting nutritionists and, as in past surveys, should be useful for informing national committees that make nutritional recommendations for cattle, as well as nutrition and management strategies employed within university research settings.

Performance Modeling and Cost Analysis of a Pilot-Scale Reverse Osmosis Process for the Final Purification of Olive Mill Wastewater

PubMed Central

Ochando-Pulido, Javier Miguel; Hodaifa, Gassan; Victor-Ortega, Maria Dolores; Martinez-Ferez, Antonio

2013-01-01

A secondary treatment for olive mill wastewater coming from factories working with the two-phase olive oil production process (OMW-2) has been set-up on an industrial scale in an olive oil mill in the premises of Jaén (Spain). The secondary treatment comprises Fenton-like oxidation followed by flocculation-sedimentation and filtration through olive stones. In this work, performance modelization and preliminary cost analysis of a final reverse osmosis (RO) process was examined on pilot scale for ulterior purification of OMW-2 with the goal of closing the loop of the industrial production process. Reduction of concentration polarization on the RO membrane equal to 26.3% was provided upon increment of the turbulence over the membrane to values of Reynolds number equal to 2.6 × 104. Medium operating pressure (25 bar) should be chosen to achieve significant steady state permeate flux (21.1 L h−1 m−2) and minimize membrane fouling, ensuring less than 14.7% flux drop and up to 90% feed recovery. Under these conditions, irreversible fouling below 0.08 L h−2 m−2 bar−1 helped increase the longevity of the membrane and reduce the costs of the treatment. For 10 m3 day−1 OMW-2 on average, 47.4 m2 required membrane area and 0.87 € m−3 total costs for the RO process were estimated. PMID:24957058

The assessment and the farmers' perceived ranking of feed resources and coping strategies with feed scarcity in smallholder dairy farming in selected district towns of Jimma Zone, Ethiopia.

PubMed

Duguma, Belay; Dermauw, Veronique; Janssens, Geert

2017-06-01

Inadequate quantity and quality of feed resources are major constraints limiting milk production and reproductive performance of dairy cattle in Ethiopia. The aim of this study was to assess dairy cattle feed resources, feeding practices, the farmers' perceived ranking of feed resources, causes of feed shortage, and coping strategies to feed scarcity in smallholder dairy system in selected district towns of Jimma Zone, Ethiopia. Data were obtained by interviewing 52 randomly selected smallholder dairy farmers using structured questionnaires and through direct observations. Results showed that 20 main feed types used by dairy farmers were identified and categorized into natural pastures, crop residues, green feeds, hay, agro-industrial by-products, concentrate mix, and non-conventional feeds. Overall, natural pasture (mean rank = 0.453), non-conventional feeds (0.307), cut green feeds (0.086), conserved hay (0.076), crop residues (0.049), and concentrate feeds (0.029) were ranked as the main feed resources in decreasing order of importance. Natural pasture grazing (92.2% of the respondents), hay (35.6%), and green feeds (29.4%) were the most important conventional basal feeds used. Wheat bran (11.7% of the respondents) followed by commercial concentrate mix (9.4%), Noug seedcake (8.3%), grain (7.8%), and molasses (6.1%) were the concentrate supplements used. Overall, bulule-flour mill leftovers (67.2% of the farmers), bean and pea hulls (57.2%) and atella-local brew by-product (37.2%), enset (Ensete ventricosum, 34.4%), and sugarcane top (32.2%) were the non-conventional feeds available and used during feed scarcity. Barley and teff (Eragrostis teff) straws and maize and sorghum stovers were the main crop residues used in the dry seasons. Overall, 73.9, 12.2, 12.2, and 1.7% of the respondents practiced free grazing, zero grazing, semi-zero, and a combination of zero- and free-grazing systems, respectively. Over 84% of the respondents in the dry season and 50% in the wet season reported experiencing a shortage of feeds. Poor feed availability (73.9% of the respondents) was reported as the main causes of feed shortage followed by shortage of pastureland (7.8%). Increased use of bulule (55.6% of the respondents), crop residues (16.1%), non-conventional feed resources (14.4%), conserved hay (11.1%), purchased green feeds and concentrates (1.1%), and reducing herd size (1.1%) were the farmers' adopted coping strategies to mitigate feed shortage. It is suggested that technical intervention to improve the quality and efficient utilization of the existing feed resources is crucial to enable sustainable feed supply and boost milk production. Technologies that are easy to adopt, feasible, and low cost are also needed to be developed in participatory manner.

Computer numerically controlled (CNC) aspheric shaping with toroidal Wheels (Abstract Only)

NASA Astrophysics Data System (ADS)

Ketelsen, D.; Kittrell, W. C.; Kuhn, W. M.; Parks, R. E.; Lamb, George L.; Baker, Lynn

1987-01-01

Contouring with computer numerically controlled (CNC) machines can be accomplished with several different tool geometries and coordinated machine axes. To minimize the number of coordinated axes for nonsymmetric work to three, it is common practice to use a spherically shaped tool such as a ball-end mill. However, to minimize grooving due to the feed and ball radius, it is desirable to use a long ball radius, but there is clearly a practical limit to ball diameter with the spherical tool. We have found that the use of commercially available toroidal wheels permits long effective cutting radii, which in turn improve finish and minimize grooving for a set feed. In addition, toroidal wheels are easier than spherical wheels to center accurately. Cutting parameters are also easier to control because the feed rate past the tool does not change as the slope of the work changes. The drawback to the toroidal wheel is the more complex calculation of the tool path. Of course, once the algorithm is worked out, the tool path is as easily calculated as for a spherical tool. We have performed two experiments with the Large Optical Generator (LOG) that were ideally suited to three-axis contouring--surfaces that have no axis of rotational symmetry. By oscillating the cutting head horizontally or vertically (in addition to the motions required to generate the power of the surface) , and carefully coordinating those motions with table rotation, the mostly astigmatic departure for these surfaces is produced. The first experiment was a pair of reflector molds that together correct the spherical aberration of the Arecibo radio telescope. The larger of these was 5 m in diameter and had a 12 cm departure from the best-fit sphere. The second experiment was the generation of a purely astigmatic surface to demonstrate the feasibility of producing axially symmetric asphe.rics while mounted and rotated about any off-axis point. Measurements of the latter (the first experiment had relatively loose tolerances) indicate an accuracy only 3 or 4 times that achieved by conventional two-axis contouring (10 AM as opposed to 3 pm rms) The successful completion of these projects demonstrates the successful application of three-axis contouring with the LOG. Toroidal cutters have also solved many of the drawbacks of spherical wheels. Work remains to be done in improving machine response and decreasing the contribution of backlash errors.

An Industrial Perspective of CAM/ROB Fuzzy Integrated Postprocessing Implementation for Redundant Robotic Workcells Applicability for Big Volume Prototyping

NASA Astrophysics Data System (ADS)

Andrés, J.; Gracia, L.; Tornero, J.; García, J. A.; González, F.

2009-11-01

The implementation of a postprocessor for the NX™ platform (Siemens Corp.) is described in this paper. It is focused on a milling redundant robotic milling workcell consisting of one KUKA KR 15/2 manipulator (6 rotary joints, KRC2 controller) mounted on a linear axis and synchronized with a rotary table (i.e., two additional joints). For carrying out a milling task, a choice among a set of possible configurations is required, taking into account the ability to avoid singular configurations by using both additional joints. Usually, experience and knowledge of the workman allow an efficient control in these cases, but being it a tedious job. Similarly to this expert knowledge, a stand-alone fuzzy controller has been programmed with Matlab's Fuzzy Logic Toolbox (The MathWorks, Inc.). Two C++ programs complement the translation of the toolpath tracking (expressed in the Cartesian space) from the NX™-CAM module into KRL (KUKA Robot Language). In order to avoid singularities or joint limits, the location of the robot and the workpiece during the execution of the task is fit after an inverse kinematics position analysis and a fuzzy inference (i.e., fuzzy criterion in the Joint Space). Additionally, the applicability of robot arms for the manufacture of big volume prototypes with this technique is proven by means of one case studied. It consists of a big orographic model to simulate floodways, return flows and retention storage of a reservoir in the Mijares river (Puebla de Arenoso, Spain). This article deals with the problem for a constant tool orientation milling process and sets the technological basis for future research at five axis milling operations.

Fabrication of nano ZrO2 dispersed novel W79Ni10Ti5Nb5 alloy by mechanical alloying and pressureless sintering

NASA Astrophysics Data System (ADS)

Sahoo, R. R.; Patra, A.; Karak, S. K.

2017-02-01

A high energy planetary ball-mill was employed to synthesize tungsten (W) based alloy with nominal composition of W79Ni10Ti5Nb5(ZrO2)1 (in wt. %) for 20 h with chrome steel as grinding media, toluene as process control agent (PCA) along with compaction at 500 MPa pressure for 5 mins and sintering at 1500°C for 2 h using Ar atmosphere. X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS), elemental mapping and Transmission electron microscopy (TEM) was used to study the phase formation, microstructure of both milled powder and consolidated alloy. The crystallite size of W in W79Ni10Ti5Nb5(ZrO2)1 powder was 37 nm, 14.7 nm at 10 h and 20 h of milling respectively and lattice strain enhances to 0.54% at 20 h of milling. The crystallite size reduction is more at 10 h of milling and the rate drop beyond 10 to 20 h of milling. The intense improvement in dislocation density was evident upto 10 h of milling and the rate decreases between 10 to 20 h of milling. Increase in the lattice parameter of tungsten in W79Ni10Ti5Nb5(ZrO2)1 alloy upto 0.09% was observed at 10 h of milling owing to severe stress assisted deformation followed by contraction upto 0.07% at 20 h of milling due to formation of solid solution. The large spherical particles at 0 h of milling transformed to elongated shape at 10 h of milling and finer morphology at 20 h of milling. The average particle size reduced from 100 µm to 4.5 µm with the progress of milling from 0 to 20 h. Formation of fine polycrystallites of W was revealed by bright field TEM analysis and the observed crystallite size from TEM study was well supported by the evaluated crystallite size from XRD. XRD pattern and SEM micrograph of sintered alloy revealed the formation of NbNi, Ni3Ti intermetallic phases. Densification of 91.5% was attained in the 20 h milled and sintered alloy. Mechanical behaviour of the sintered product was evaluated by hardness and wear study. W79Ni10Ti5Nb5(ZrO2)1 alloy showed increase in hardness with decreasing load. The wear rate increases with increasing load due to higher abrasion effect at higher load.

An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring.

PubMed

Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

2016-02-23

An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies.

An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring

PubMed Central

Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

2016-01-01

An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies. PMID:26907297

The gas-sensing potential of nanocrystalline SnO2 produced by a mechanochemical milling via centrifugal action

NASA Astrophysics Data System (ADS)

Kersen, Ü.

In this work, the synthesis of undoped nanocrystalline tin dioxide powders and the subsequent preparation of SnO2 thick-films were studied. An initial mixture of SnCl2 and Ca(OH)2 was sealed in a vial for milling in an air atmosphere. Heat treatment of the milled powder resulted in the formation of tetragonal and orthorhombic SnO2 phases, which was confirmed by X-ray diffraction (XRD) analysis. It was found that crystallite size could be controlled by varying the milling time, the rotation speed and the temperature used for the heat treatment. Crystallite sizes in the range 20 to 30 nm (determined by XRD measurements) were obtained. The total pore volume was 0.22 ml/g for a measured particle size of 37 m2/g. No contamination of the powder during milling was found. The response of the prepared thick-films to H2S gas in the concentration range 0.5 to 10 ppm in air was investigated as a function of the preparation conditions. The advantage of mechanochemical synthesis of powder is its relative simplicity, low cost and possibility of obtaining isolated, unagglomerated nanosized grains. It is shown that chemical reactions, which usually occur in the vibratory mill to produce the SnO phase, can also be initiated during a short processing time in the centrifugal mill.

Effects of airborne Aspergillus on serum aflatoxin B1 and liver enzymes in workers handling wheat flour.

PubMed

Saad-Hussein, A; Taha, M M; Fadl, N N; Awad, A-H; Mahdy-Abdallah, H; Moubarz, G; Aziz, H; El-Shamy, K A

2016-01-01

The present work aimed to investigate the relationship between occupational exposure to airborne molds, serum aflatoxin B1 (AFB1), and liver enzymes of workers handling wheat flour. The study included 90 bakers, 100 flour milling workers, and 100 controls with no exposure to flour dust. Workplace aspects such as temperature and relative humidity were measured. Airborne fungi were collected and identified. In all subjects included, the serum levels of AFB1, serum albumin (Alb), aspartate aminotransferase (AST), alanine aminotransferase (ALT), and alkaline phosphatase (ALP) were measured. Air temperature and relative humidity were found to be higher in bakeries than in flour mill sections. Airborne Aspergillus species were isolated in dust particles <8 µm in size. The concentration of Aspergillus flavus and Aspergillus niger were higher in bakeries than in the flour mill sections. They were higher in the grinding section than in other mill sections. The serum AFB1-Alb adduct and ALP levels were significantly higher in bakers compared to milling workers (p < 0.0001, p = 0.05), respectively. The liver enzymes AST and ALT were significantly higher among milling workers and bakers than controls (p < 0.05, p < 0.0001), respectively. The duration of exposure was significantly correlated with serum AFB1 in bakers. Moreover, there was significant correlation between serum AFB1, each of ALT and AST levels in bakers. chronic occupational exposure to high concentrations of Aspergillus in workplaces may cause elevations in serum levels of AFB1 and liver enzymes in workers exposed to flour dust. Hence, worker protection measures should be consistently adopted and enforced at the workplace. © The Author(s) 2015.

The transcriptome of the developing grain: a resource for understanding seed development and the molecular control of the functional and nutritional properties of wheat.

PubMed

Rangan, Parimalan; Furtado, Agnelo; Henry, Robert J

2017-10-11

Wheat is one of the three major cereals that have been domesticated to feed human populations. The composition of the wheat grain determines the functional properties of wheat including milling efficiency, bread making, and nutritional value. Transcriptome analysis of the developing wheat grain provides key insights into the molecular basis for grain development and quality. The transcriptome of 35 genotypes was analysed by RNA-Seq at two development stages (14 and 30 days-post-anthesis, dpa) corresponding to the mid stage of development (stage Z75) and the almost mature seed (stage Z85). At 14dpa, most of the transcripts were associated with the synthesis of the major seed components including storage proteins and starch. At 30dpa, a diverse range of genes were expressed at low levels with a predominance of genes associated with seed defence and stress tolerance. RNA-Seq analysis of changes in expression between 14dpa and 30dpa stages revealed 26,477 transcripts that were significantly differentially expressed at a FDR corrected p-value cut-off at ≤0.01. Functional annotation and gene ontology mapping was performed and KEGG pathway mapping allowed grouping based upon biochemical linkages. This analysis demonstrated that photosynthesis associated with the pericarp was very active at 14dpa but had ceased by 30dpa. Recently reported genes for flour yield in milling and bread quality were found to influence wheat quality largely due to expression patterns at the earlier seed development stage. This study serves as a resource providing an overview of gene expression during wheat grain development at the early (14dpa) and late (30dpa) grain filling stages for use in studies of grain quality and nutritional value and in understanding seed biology.

Compounding rifampin suspensions with improved injectability for nasogastric enteral feeding tube administration.

PubMed

de Villiers, Melgardt M; Vogel, Laura; Bogenschutz, Monica C; Fingerhut, Bonnie J; D'Silva, Joseph B; Moore, Anne

2010-01-01

Often medications that have to be administered to patients via a nasogastric enteral feeding tubes are only available as tablets and capsules with no suitable commercial liquid alternatives. In such situations, pharmacists and nurses have to compound the tablets and capsule contents into liquid suspension formulations for dosing. The risk of occlusion of the enteral tubes during administration is reduced by employing liquid suspensions that are composed of small and uniform particles, not subject to rapid rates of settling, resistant to caking, and easily and uniformly re-suspended upon agitation. Present techniques often employ a manual process, such as a mortar and pestle, to accomplish the particle size reduction and subsequent incorporation into a suitable liquid diluent. A new compounding device has been invented that employs an automated wet-milling process in a single-use disposable plastic container to compound the suspensions. The two processes were compared using Rifampin capsules and various liquid diluents. A prototype version of the new device was employed in the experiments. The physical characteristics of the compounded suspensions were evaluated by determining sedimentation rate, sedimentation volume, and particle size and shape using laser light scattering, optical microscopy, and scanning electron microscopy techniques. The use characteristic of the compounded suspensions was evaluated using a nasogastric tube inject ability test. The results indicated that suspensions prepared using the new device were more resistant to sedimentation and caking and were easier to re-disperse into a uniform mixture by gentle shaking. The results were a consequence of the particles generated by the new device which were found to be smaller and more uniform in shape and size. The suspensions prepared using the new device did not cause blockage of the enteral feeding tubes in comparison to those prepared using a mortar and pastle. In conclusion, the results indicate that the wet-milling process employed by the new compounding device produces liquid suspensions that are more suitable for dosing via nasogastric enteral tubes in comparison to the manual mortar and pestle method that is presently employed.

29. INTERIOR VIEW LOOKING SOUTHWEST IN THE ELECTRICAL MOTOR ROOM. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. INTERIOR VIEW LOOKING SOUTHWEST IN THE ELECTRICAL MOTOR ROOM. CONTROL PANELS ARE ON THE LEFT SIDE OF THE IMAGE (MOST OF THE SALVAGEABLE EQUIPMENT HAS BEEN REMOVED FROM THESE PANELS. A TRANSFORMER FOR GENERAL ELECTRICAL NEEDS IN THE MILL IS LOCATED ABOVE THE DOOR. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Effects of site preparation treatments on early growth and survival of planted longleaf pine (Pinus palustris Mill.) seedlings in North Carolina

Treesearch

Benjamin O. Knapp; G. Geoff Wang; Joan L. Walker; Susan Cohen

2006-01-01

We tested the effects of eight site preparation treatments on early growth and survival of container-grown longleaf pine (Pinus palustris Mill.) seedlings. Treatments included an untreated check, six combinations of two initial vegetation control treatments (chopping or herbicide) with three planting site conditions (flat [no additional treatment],...

Effect of process control agent on the porous structure and mechanical properties of a biomedical Ti-Sn-Nb alloy produced by powder metallurgy.

PubMed

Nouri, A; Hodgson, P D; Wen, C E

2010-04-01

The influence of different amounts and types of process control agent (PCA), i.e., stearic acid and ethylene bis-stearamide, on the porous structure and mechanical properties of a biomedical Ti-16Sn-4Nb (wt.%) alloy was investigated. Alloy synthesis was performed on elemental metal powders using high-energy ball milling for 5h. Results indicated that varying the PCA content during ball milling led to a drastic change in morphology and particle-size distribution of the ball-milled powders. Porous titanium alloy samples sintered from the powders ball milled with the addition of various amounts of PCA also revealed different pore morphology and porosity. The Vickers hardness of the sintered titanium alloy samples exhibited a considerable increase with increasing PCA content. Moreover, the addition of larger amounts of PCA in the powder mixture resulted in a significant increase in the elastic modulus and peak stress for the sintered porous titanium alloy samples under compression. It should also be mentioned that the addition of PCA introduced contamination (mainly carbon and oxygen) into the sintered porous product. Crown Copyright 2009. Published by Elsevier Ltd. All rights reserved.

SASS Applied to Optimum Work Roll Profile Selection in the Hot Rolling of Wide Steel

NASA Astrophysics Data System (ADS)

Nolle, Lars

The quality of steel strip produced in a wide strip rolling mill depends heavily on the careful selection of initial ground work roll profiles for each of the mill stands in the finishing train. In the past, these profiles were determined by human experts, based on their knowledge and experience. In previous work, the profiles were successfully optimised using a self-organising migration algorithm (SOMA). In this research, SASS, a novel heuristic optimisation algorithm that has only one control parameter, has been used to find the optimum profiles for a simulated rolling mill. The resulting strip quality produced using the profiles found by SASS is compared with results from previous work and the quality produced using the original profile specifications. The best set of profiles found by SASS clearly outperformed the original set and performed equally well as SOMA without the need of finding a suitable set of control parameters.

Dietary milled flaxseed and flaxseed oil improve N-3 fatty acid status and do not affect glycemic control in individuals with well-controlled type 2 diabetes.

PubMed

Taylor, Carla G; Noto, Amy D; Stringer, Danielle M; Froese, Sylvia; Malcolmson, Linda

2010-02-01

To determine the effects of dietary consumption of milled flaxseed or flaxseed oil on glycemic control, n-3 fatty acid status, anthropometrics, and adipokines in individuals with type 2 diabetes. Thirty-four participants were randomized into a parallel, controlled trial. The participants were adults with type 2 diabetes (age 52.4 +/- 1.5 years, body mass index 32.4 +/- 1.0 kg/m(2), n = 17 men and 17 women). Participants consumed a selection of bakery products containing no flax (control group [CTL], n = 9), milled flaxseed (FXS, n = 13; 32 g/d), or flaxseed oil (FXO, n = 12; 13 g/d) daily for 12 weeks. The FXS and FXO groups received equivalent amounts of alpha-linolenic acid (ALA; 7.4 g/day). The primary outcome measures were fasting plasma hemoglobin A(1c), glucose, insulin, and phospholipid fatty acid composition. The secondary outcome measures were fasting circulating leptin and adiponectin, as well as body weight, body mass index, and waist circumference. Dietary intake assessment and calculations for homeostasis model assessment for insulin resistance and quantified insulin sensitivity check were also completed. The FXS and FXO groups had increases in plasma phospholipid n-3 fatty acids (ALA, eicosapentaenoic acid [EPA], or decosapentaenoic acid [DPA], but not docosahexaenoic acid), and the FXO group had more EPA and DPA in plasma phospholipids compared to the FXS group. All groups had similar caloric intakes; however, the CTL group experienced a 4% weight gain compared to baseline (p < 0.05), while both flax groups had constant body weights during the study period. All other parameters, including glycemic control, were unchanged by dietary treatment. Milled FXS and FXO intake does not affect glycemic control in adults with well-controlled type 2 diabetes. Possible prevention of weight gain by flax consumption warrants further investigation.

SBR treatment of olive mill wastewaters: dilution or pre-treatment?

PubMed

Farabegoli, G; Chiavola, A; Rolle, E

2012-01-01

The olive-oil extraction industry is an economically important activity for many countries of the Mediterranean Sea area, with Spain, Greece and Italy being the major producers. This activity, however, may represent a serious environmental problem due to the discharge of highly polluted effluents, usually referred to as 'olive mill wastewaters' (OMWs). They are characterized by high values of chemical oxygen demand (COD) (80-300 g/L), lipids, total polyphenols (TPP), tannins and other substances difficult to degrade. An adequate treatment before discharging is therefore required to reduce the pollutant load. The aim of the present paper was to evaluate performances of a biological process in a sequencing batch reactor (SBR) fed with pre-treated OMWs. Pre-treatment consisted of a combined acid cracking (AC) and granular activated carbon (GAC) adsorption process. The efficiency of the system was compared with that of an identical SBR fed with the raw wastewater only diluted. Combined AC and GAC adsorption was chosen to be used prior to the following biological process due to its capability of providing high removal efficiencies of COD and TPP and also appreciable improvement of biodegradability. Comparing results obtained with different influents showed that best performances of the SBR were obtained by feeding it with raw diluted OMWs (dOMWs) and at the lowest dilution ratio (1:25): in this case, the removal efficiencies were 90 and 76%, as average, for COD and TPP, respectively. Feeding the SBR with either the pre-treated or the raw dOMWs at 1:50 gave very similar values of COD reduction (74%); however, an improvement of the TPP removal was observed in the former case.

In vitro and in vivo assessment of the effect of initial moisture content and drying temperature on the feeding value of maize grain.

PubMed

Huart, F; Malumba, P; Odjo, S; Al-Izzi, W; Béra, F; Beckers, Y

2018-06-11

1. This study assessed the impact of drying temperature (54, 90, and 130°C) and maize grain moisture content at harvest (36% and 29%) on in vitro digestibility, the growth performance and ileal digestibility of broiler chickens. 2. In contrast to the results from the in vitro digestibility, apparent ileal digestibility of starch and energy decreased when the drying temperature was raised from 54 to 130°C, and this effect was more pronounced in maize grain harvested at high initial moisture content (36%). Ileal protein digestibility of maize grain decreased significantly when dried at the intermediate temperature (90°C) and with a high harvest moisture content (36%). Drying temperature and initial moisture content did not significantly affect AMEn. 3. When maize was dried at 130°C, the particle sizes of flour recovered after standard milling procedures decreased significantly, which would influence animal growth performance and in vivo digestibility through animal feed selection.

Effect of co-milled wheat, green gram and barley on the rheological and quality characteristics of cookies.

PubMed

Tulse, Siddharth B; V, Reshma; Rajiv, Jyotsna; Sakhare, Suresh D

2015-10-01

Studies were carried out on the co-milling of wheat (W), green gram (GG) and barley (BR) grains using a roller milling system. The co-milled straight run flours obtained by varying proportions of wheat, barley and green gram WGGBR-1 (90:5:5), WGGBR-2 (80:10:10) and WGGBR-3 (70:15:15) were used in the cookie baking experiments. As the amount of GG and BR increased in blend, water absorption increased (56.5-58.4%) and dough stability and extensibility values decreased (104-92 mm). Hardness of cookie doughs and spread ratio (7.70-6.00) of cookies decreased and breaking strength values increased from 2900 to 3700 g in cookies made using co-milled blends WGGBR-1, WGGBR-2 and WGGBR-3. The highest breaking strength value (3700 g), large islands, gummy mouth feel and lowest overall quality score of 51.5 were recorded for cookies made with blend WGGBR-3 indicating that the cookies had unacceptable hard texture. The optimum blend for cookies was WGGBR-2 (80:10:10) and the cookies possessed slightly small islands, crisp, light texture and a pleasant taste. These cookies had 12.30 and 8.00% protein and dietary fibre as against the control cookie values of 8 and 4%, respectively. The in vitro protein digestibility of the control cookies was 61% and it was 51% for cookies made with WGGBR-2 blend. © The Author(s) 2014.

Design and evaluation of a Stochastic Optimal Feed-forward and Feedback Technology (SOFFT) flight control architecture

NASA Technical Reports Server (NTRS)

Ostroff, Aaron J.; Proffitt, Melissa S.

1994-01-01

This paper describes the design and evaluation of a stochastic optimal feed-forward and feedback technology (SOFFT) control architecture with emphasis on the feed-forward controller design. The SOFFT approach allows the designer to independently design the feed-forward and feedback controllers to meet separate objectives and then integrate the two controllers. The feed-forward controller has been integrated with an existing high-angle-of-attack (high-alpha) feedback controller. The feed-forward controller includes a variable command model with parameters selected to satisfy level 1 flying qualities with a high-alpha adjustment to achieve desired agility guidelines, a nonlinear interpolation approach that scales entire matrices for approximation of the plant model, and equations for calculating feed-forward gains developed for perfect plant-model tracking. The SOFFT design was applied to a nonlinear batch simulation model of an F/A-18 aircraft modified for thrust vectoring. Simulation results show that agility guidelines are met and that the SOFFT controller filters undesired pilot-induced frequencies more effectively during a tracking task than a flight controller that has the same feedback control law but does not have the SOFFT feed-forward control.

A case-control study of bladder cancer in the United States rubber and tyre industry.

PubMed

Checkoway, H; Smith, A H; McMichael, A J; Jones, F S; Monson, R R; Tyroler, H A

1981-08-01

A case-control study of bladder cancer was conducted in five United States rubber and tyre companies to determine if there were high-risk jobs and work areas within the industry. The study included 220 male cases of bladder cancer, of whom 107 were identified from hospital record reviews and 113 from death certificates. Each case was matched individually with two industry controls by sex, race, year of birth, and company. One control was matched additionally by year of hire and duration of employment. Comparisons of cases and controls not matched by year of hire and age of hire showed no differences for those variables, which suggests that age and calendar period of first exposure to the industry were not risk determinants. When the work histories of both cases and controls were contrasted it was found that cases were more likely than controls to have worked in milling (odds ratio (OR) = 1.91) and calender operation (OR = 2.21) jobs. The relative risk estimates for milling and calender operation both exhibited linear trends of increase with duration of exposure. Milling and calender operation jobs entail potential exposures to volatilised reaction products from heated rubber stock. A better understanding of aetiological associations with job type will require more detailed characterisation of the work environment with regard to the sources and levels of aromatic amines and other suspected bladder carcinogens.

A case-control study of bladder cancer in the United States rubber and tyre industry.

PubMed Central

Checkoway, H; Smith, A H; McMichael, A J; Jones, F S; Monson, R R; Tyroler, H A

1981-01-01

A case-control study of bladder cancer was conducted in five United States rubber and tyre companies to determine if there were high-risk jobs and work areas within the industry. The study included 220 male cases of bladder cancer, of whom 107 were identified from hospital record reviews and 113 from death certificates. Each case was matched individually with two industry controls by sex, race, year of birth, and company. One control was matched additionally by year of hire and duration of employment. Comparisons of cases and controls not matched by year of hire and age of hire showed no differences for those variables, which suggests that age and calendar period of first exposure to the industry were not risk determinants. When the work histories of both cases and controls were contrasted it was found that cases were more likely than controls to have worked in milling (odds ratio (OR) = 1.91) and calender operation (OR = 2.21) jobs. The relative risk estimates for milling and calender operation both exhibited linear trends of increase with duration of exposure. Milling and calender operation jobs entail potential exposures to volatilised reaction products from heated rubber stock. A better understanding of aetiological associations with job type will require more detailed characterisation of the work environment with regard to the sources and levels of aromatic amines and other suspected bladder carcinogens. PMID:7272236

Effect of ball-milling surfactants on the interface chemistry in hot-compacted SmCo5 magnets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, WF; Sepehri-Amin, H; Zheng, LY

2012-11-01

Anisotropic SmCo5 nanoflakes prepared by high-energy ball-milling with surfactants have great potential in applications for high-performance nanocomposite magnets. For such "nanocomposite" applications, the surface structure and chemistry of nanoflakes are crucial for achieving high coercivity. In this study, hot-pressed samples from anisotropic SmCo5 nanoflakes, ball-milled with different surfactants, oleic acid (OA) and oleylamine (OY), were investigated. Interface layers between the SmCo5 nanoflakes were found to consist of samarium oxides and a soft magnetic Co phase. These surface layers contribute to the degradation of hard magnetic performance, which is confirmed by scanning transmission electron microscopy-energy dispersive X-ray spectroscopy analysis of themore » cross-section of a single flake ball-milled with OA. Samples milled with OY show a much thinner interface layer in compacted samples, which means that the surface degradation during ball-milling with OY is much less than that with OA. The results show clearly that the choice of proper surfactant and the control of processing parameters are the key factors for improving the surface condition of the nanoflakes and the resulting hard magnetic properties. (C) 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.« less

Optimization of the Technological Synthesis of Refractory Compounds

NASA Astrophysics Data System (ADS)

Gaidar, S. M.; Karelina, M. Yu.; Prikhod'ko, V. M.; Volkov, A. A.

2017-12-01

The results of experimental studies, which are related to the regulation of the fractional composition of refractory compounds by roll milling in using controlled roll opening and unbalanced peripheral speeds of rollers, are reported. The content of prepared fine, middle, and coarse fractions is within 50-80%; in this case, the milling time of synthesis products is less than the time of ball milling by an order of magnitude. The application of roll milling for refining the products of self-propagating high-temperature synthesis can be most efficient in using together with heat-generating reactor to solve the main problem of self-propagating synthesis (SHS), which is a problem for recent several decades (the problem is the creation of intense automated production of refractory compounds in using continuous manufacturing cycle within a energotechnological system with the recovery of a great quantity of heat released during SHS).

Hydroamination reactions of alkynes with ortho-substituted anilines in ball mills: synthesis of benzannulated N-heterocycles by a cascade reaction.

PubMed

Weiße, Maik; Zille, Markus; Jacob, Katharina; Schmidt, Robert; Stolle, Achim

2015-04-20

It was demonstrated that ortho-substituted anilines are prone to undergo hydroamination reactions with diethyl acetylenedicarboxylate in a planetary ball mill. A sequential coupling of the intermolecular hydroamination reaction with intramolecular ring closure was utilized for the syntheses of benzooxazines, quinoxalines, and benzothiazines from readily available building blocks, that is, electrophilic alkynes and anilines with OH, NH, or SH groups in the ortho position. For the heterocycle formation, it was shown that several stress conditions were able to initiate the reaction in the solid state. Processing in a ball mill seemed to be advantageous over comminution with mortar and pestle with respect to process control. In the latter case, significant postreaction modification occurred during solid-state analysis. Cryogenic milling proved to have an adverse effect on the molecular transformation of the reagents. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of Nano-Crystalline Gamma-TiAl Materials

NASA Technical Reports Server (NTRS)

Hales, Stephen J.; Vasquez, Peter

2003-01-01

One of the principal problems with nano-crystalline materials is producing them in quantities and sizes large enough for valid mechanical property evaluation. The purpose of this study was to explore an innovative method for producing nano-crystalline gamma-TiAl bulk materials using high energy ball milling and brief secondary processes. Nano-crystalline powder feedstock was produced using a Fritsch P4(TM) vario-planetary ball mill recently installed at NASA-LaRC. The high energy ball milling process employed tungsten carbide tooling (vials and balls) and no process control agents to minimize contamination. In a collaborative effort, two approaches were investigated, namely mechanical alloying of elemental powders and attrition milling of pre-alloyed powders. The objective was to subsequently use RF plasma spray deposition and short cycle vacuum hot pressing in order to effect consolidation while retaining nano-crystalline structure in bulk material. Results and discussion of the work performed to date are presented.

Airway responsiveness to methacholine, respiratory symptoms, and dust exposure levels in grain and flour mill workers in eastern France.

PubMed

Massin, N; Bohadana, A B; Wild, P; Kolopp-Sarda, M N; Toamain, J P

1995-06-01

Our goal was to assess the relation between dust exposure levels and the respiratory health status of workers in grain and flour mills in eastern France. We studied 118 male workers from 11 mills and 164 unexposed male controls. Dust concentration was measured by personal sampling methods. Outcome variables included respiratory symptoms, routine pulmonary function tests, and indices of airway responsiveness to methacholine. A great within- and between-area variability of inhalable dust concentration was found in all mills. A dose-response relationship was observed between dust exposure levels and chronic respiratory symptoms, suggesting that exposure to grain and flour dust may lead to chronic bronchitis. A significant relation was found between dust exposure and airway hyper-responsiveness; this finding is important since it has been hypothesized that the latter abnormality may lead to or be a predisposing factor in subsequent chronic, irreversible airflow obstruction.

Lightning prevention systems for paper mills

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carpenter, R.B. Jr.

1989-05-01

Paper mills are increasingly relying on sensitive electronic equipment to control their operations. However, the sensitivity of these devices has made mills vulnerable to the effects of lightning strokes. An interruption in the power supply or the destruction of delicate microcircuits can have devastating effects on mill productivity. The authors discuss how lightning strokes can be prevented by a Dissipation Array system (DAS). During the past 17 years, the concept has been applied to a host of applications in regions with a high incidence of lightning activity. With nearly 700 systems now installed, more than 4000 system-years of history havemore » been accumulated. Areas as large as 1 km{sup 2} and towers as high as 2000 ft have been protected and completely isolated from lightning strokes. There have been very few failures, and in every case, the cause of the failure was determined and corrected.« less

Mineralogical controls on aluminum and magnesium in uranium mill tailings: Key Lake, Saskatchewan, Canada.

PubMed

Gomez, M A; Hendry, M J; Koshinsky, J; Essilfie-Dughan, J; Paikaray, S; Chen, J

2013-07-16

The mineralogy and evolution of Al and Mg in U mill tailings are poorly understood. Elemental analyses (ICP-MS) of both solid and aqueous phases show that precipitation of large masses of secondary Al and Mg mineral phases occurs throughout the raffinate neutralization process (pH 1-11) at the Key Lake U mill, Saskatchewan, Canada. Data from a suite of analytical methods (ICP-MS, EMPA, laboratory- and synchrotron-based XRD, ATR-IR, Raman, TEM, EDX, ED) and equilibrium thermodynamic modeling showed that nanoparticle-sized, spongy, porous, Mg-Al hydrotalcite is the dominant mineralogical control on Al and Mg in the neutralized raffinate (pH ≥ 6.7). The presence of this secondary Mg-Al hydrotalcite in mineral samples of both fresh and 15-year-old tailings indicates that the Mg-Al hydrotalcite is geochemically stable, even after >16 years in the oxic tailings body. Data shows an association between the Mg-Al hydrotalcite and both As and Ni and point to this Mg-Al hydrotalcite exerting a mineralogical control on the solubility of these contaminants.

Mineral scale management Part III, Nonprocess elements in the paper industry

Treesearch

Alan W. Rudie; Peter W. Hart

2006-01-01

Efforts to comply with effluent standards have led to a situation where mills have little leeway in managing trace metals without developing mineral scale deposits. In most cases, the trace metals can be managed with minor process changes and siitable levels of process control. The principal tools available to the mill are pH and good washing in the first chorine...

Phanerochaete flavido-alba Laccase Induction and Modification of Manganese Peroxidase Isoenzyme Pattern in Decolorized Olive Oil Mill Wastewaters

PubMed Central

Pérez, J.; de la Rubia, T.; Hamman, O. Ben; Martínez, J.

1998-01-01

Lignin-degrading enzymes were partially purified from supernatant solutions obtained from Phanerochaete flavido-alba-decolorized olive oil mill wastewaters (OMW). The dominant enzymes, manganese peroxidases, exhibited different isoform patterns in decolorized OMW-containing cultures than in residue-free samples. Laccase induction was also detected in OMW-containing cultures but not in control cultures. PMID:9647858

Indirect interactions between arbuscular mycorrhizal fungi and Spodoptera exigua alter photosynthesis and plant endogenous hormones.

PubMed

He, Lei; Li, Changyou; Liu, Runjin

2017-08-01

Peanut (Arachis hypogaea Linn. cv: Luhua 11) and tomato (Lycopersicon esculentum Mill. cv: Zhongshu 4) were inoculated with arbuscular mycorrhizal fungi (AMF) Funneliformis mosseae BEG167 (Fm), Rhizophagus intraradices BEG141 (Ri), and Glomus versiforme Berch (Gv), and/or Spodoptera exigua (S. exigua) under greenhouse conditions. Results indicated that feeding by S. exigua had little influence on colonization of peanut plants by AMF, but improved colonization of tomato by Fm and Gv. Feeding by S. exigua had little influence on leaf net photosynthetic rate, transpiration rate, and stomatal conductance of nonmycorrhizal peanut plants but significantly improved net photosynthetic rate and transpiration rate of mycorrhizal plants of both hosts. AMF with or without S. exigua inoculation improved host plant photosynthetic characteristics, growth, and hormone status. Fm showed maximum beneficial effects, followed by Gv. The concentrations and ratios of phytohormones abscisic acid (ABA), indole-3-acetic acid (IAA), gibberellin (GA), zeatin riboside (ZR), and jasmonic acid (JA) in the leaves of the host plants were changed due to the interaction between AMF and S. exigua. Generally, AMF with or without S. exigua inoculation increased the concentrations of GA, ZR, and JA and the ratios of IAA/ABA, GA/ABA, ZR/ABA, and IAA + GA + ZR/ABA, while feeding by S. exigua on nonmycorrhizal plants showed the opposite effect. The concentration of JA in the leaves of peanut and tomato inoculated with Fm or Fm + S. exigua was 1.9 and 1.9 times and 2.5 and 2.7 times, respectively, greater than that of the controls inoculated with neither. There was a negative correlation between the JA concentration and the survival percentage of S. exigua larva. We conclude that indirect interactions between AMF and insect herbivores changed the photosynthetic and hormone characteristics, and ratios of phytohormones, thereby revealing mechanisms of belowground-aboveground interactions.

Experience of Application of Liquid Lubricating Materials during Wide Strip Hot Rolling

NASA Astrophysics Data System (ADS)

Platov, S. I.; Dema, R. R.; Kharchenko, M. V.; Amirov, R. N.

2017-12-01

The paper presents the results of the scientific and practical research of roller systems operation at feed of liquid lubricating materials through the example of the wide strip hot rolling Mill-2000 at PAO MMK. The experiments proved that application of lubricating materials leads to decrease of energy-power parameters of the process by 12 to 15 %, and reduction of work roll wear by 10 to 12%. The practical results of the study are developed recommendations on determination of consumption-volumetric parameters of the supplied lubricating material depending on rheological and geometrical parameters of the rolled strip and current wear of work rolls.

Surface Roughness Optimization Using Taguchi Method of High Speed End Milling For Hardened Steel D2

NASA Astrophysics Data System (ADS)

Hazza Faizi Al-Hazza, Muataz; Ibrahim, Nur Asmawiyah bt; Adesta, Erry T. Y.; Khan, Ahsan Ali; Abdullah Sidek, Atiah Bt.

2017-03-01

The main challenge for any manufacturer is to achieve higher quality of their final products with maintains minimum machining time. In this research final surface roughness analysed and optimized with maximum 0.3 mm flank wear length. The experiment was investigated the effect of cutting speed, feed rate and depth of cut on the final surface roughness using D2 as a work piece hardened to 52-56 HRC, and coated carbide as cutting tool with higher cutting speed 120-240 mm/min. The experiment has been conducted using L9 design of Taguchi collection. The results have been analysed using JMP software.

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 3 2013-07-01 2013-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 3 2012-07-01 2012-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

31 CFR 540.317 - Uranium feed; natural uranium feed.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance:Treasury 3 2014-07-01 2014-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

DDR-type zeolite membrane synthesis, modification and gas permeation studies

DOE PAGES

Yang, Shaowei; Cao, Zishu; Arvanitis, Antonios; ...

2016-01-22

DDR-type zeolite membrane was synthesized on porous α-alumina substrate by hydrothermal treatment of a ball-milled Sigmal-1 crystal seed layer in an aluminum-free precursor solution containing 1-Adamantylamine as the structure directing agent (SDA). The as-synthesized DDR zeolite membranes were defect-free but the supported zeolite layers were susceptible to crack development during the subsequent high-temperature SDA removal process. The cracks were effectively eliminated by the liquid phase chemical deposition method using tetramethoxysilane as the precursor for silica deposits. The modified membrane was extensively studied for H 2, He, O 2, N 2, CO 2, CH 4, and i-C 4H 10 pure gasmore » permeation and CO 2/CH 4 mixture separation. At 297 K and 2-bar feed gas pressure, the membrane achieved a CO 2/CH 4 separation factor of ~92 for a feed containing 90% CO 2, which decreased to 62 for a feed containing 10% CO 2 with the CO 2 permeance virtually unchanged at ~1.8×10 –7 mol/m• sup>2 s • Pa regardless of the feed composition. It also exhibited an O 2/N 2 permselectivity of 1.8 at 297 K. Furthermore, the gas permeation behaviors of the current aluminum-containing DDR type zeolite membrane are generally in good agreement with the findings in both experimental and theoretical studies on the pure-silica DDR membranes in recent literature.« less

Radium-226 whole-body gamma counting and 222Rn breath analysis: report on a subject exposed to uranium mill tailings.

PubMed

Lucas, H F

1991-02-01

One of two boys born in September 1949 who played on U mill tailings between age 8 and 12 was diagnosed as having leukemia at age 15.5. The exposed and control subjects were well matched; they were approximately the same age and both were 1.85 m (6' 1") in height and weighed 75.2 kg (165 pounds). The result obtained by gamma spectrometric method for the exposed subject was 0 +/- 17 Bq (0 +/- 470 pCi), while that for the control subject was 4 +/- 15 Bq (100 +/- 400 pCi). The result obtained by the Rn breath method for the exposed subject was 4.4 +/- 0.7 Bq (120 +/- 20 pCi), while that for the control was 5.4 +/- 1.4 Bq (150 +/- 38 pCi). These results suggest that the 226Ra body burden of the exposed subject is within the range of those observed in subjects exposed only through normal food sources, which have a mean 226Ra content of 1.5 Bq (range: 0.4-4.4 Bq) so that no significant mill-tailing intake is indicated. The best estimate of alpha particle dose to the red marrow from 226Ra and its decay products was 0.05 mGy at age 14 and 0.10 mGy at age 38. This dose, when compared to that observed in the dial painters, suggests that the leukemia was not caused by uptake of Ra from the mill tailings.

Neural and Molecular Mechanisms Involved in Controlling the Quality of Feeding Behavior: Diet Selection and Feeding Patterns

PubMed Central

2017-01-01

We are what we eat. There are three aspects of feeding: what, when, and how much. These aspects represent the quantity (how much) and quality (what and when) of feeding. The quantitative aspect of feeding has been studied extensively, because weight is primarily determined by the balance between caloric intake and expenditure. In contrast, less is known about the mechanisms that regulate the qualitative aspects of feeding, although they also significantly impact the control of weight and health. However, two aspects of feeding quality relevant to weight loss and weight regain are discussed in this review: macronutrient-based diet selection (what) and feeding pattern (when). This review covers the importance of these two factors in controlling weight and health, and the central mechanisms that regulate them. The relatively limited and fragmented knowledge on these topics indicates that we lack an integrated understanding of the qualitative aspects of feeding behavior. To promote better understanding of weight control, research efforts must focus more on the mechanisms that control the quality and quantity of feeding behavior. This understanding will contribute to improving dietary interventions for achieving weight control and for preventing weight regain following weight loss. PMID:29053636

Risk Factors for Developing Work-Related Musculoskeletal Disorders during Dairy Farming.

PubMed

Taghavi, Sayed Mohammad; Mokarami, Hamidreza; Ahmadi, Omran; Stallones, Lorann; Abbaspour, Asghar; Marioryad, Hossein

2017-01-01

Dairy farming work involves frequent use of poor postures. These postures may increase the risk of developing musculoskeletal disorders among dairy workers. To assess postural load during performance of various tasks related to dairy farming. This cross-sectional study was conducted on a dairy farm in Iran. In order to assess postural load, tasks related to dairy farming were divided into 3 categories: feeding, milking, and manure disposal. Each task was then divided into its constituent work subdivisions (tasks). Finally, the working posture for each work subdivision was evaluated using Rapid Entire Body Assessment (REBA). Based on the results from the REBA score, the poorest risk scores (risk level 4) were associated with the following tasks: (1) manure disposal, (2) filling feed bags, and (3) pouring milk into a bucket. Other tasks such as filling corn containers, pouring corn into the milling machine, preparing the feed, pouring food into mangers, attaching the milking machine, and pouring milk from a bucket into a tank imposed high risk (risk level 3). The risk for the tasks of washing and disinfecting the udders were assessed as medium risks. The risk levels associated with most of the tasks on the studied farm were unacceptably high. Therefore, it is essential to implement ergonomic interventions to reduce risk levels of the tasks.

Fabrication and Characterization of novel W80Ni10Nb10 alloy produced by mechanical alloying

NASA Astrophysics Data System (ADS)

Saxena, R.; Patra, A.; Karak, S. K.; Pattanaik, A.; Mishra, S. C.

2016-02-01

Nanostructured tungsten (W) based alloy with nominal composition of W80Ni10Nb10 (in wt. %) was synthesized by mechanical alloying of elemental powders of tungsten (W), nickel (Ni), niobium (Nb) in a high energy planetary ball-mill for 20 h using chrome steel as grinding media and toluene as process control agent followed by compaction at 500 MPa pressure for 5 mins and sintering at 1500°C for 2 h in Ar atmosphere. The phase evolution and the microstructure of the milled powder and consolidated product were investigated by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The crystallite size of W in W80Ni10Nb10 powder was reduced from 100 μm at 0 h to 45.6 nm at 10 h and 34.1 nm at 20 h of milling whereas lattice strain increases to 35% at 20 h of milling. The dislocation density shows sharp increase up to 5 h of milling and the rate of increase drops beyond 5 to 20 h of milling. The lattice parameter of tungsten in W80Ni10Nb10 expanded upto 0.04% at 10 h of milling and contracted upto 0.02% at 20 h of milling. The SEM micrograph revealed the presence of spherical and elongated particles in W80Ni10Nb10 powders at 20 h of milling. The particle size decreases from 100 μm to 2 μm with an increase in the milling time from 0 to 20 hours. The crystallite size of W in milled W80Ni10Nb10 alloy as evident from bright field TEM image was in well agreement with the measured crystallite size from XRD. Structure of W in 20 h milled W80Ni10Nb10 alloy was identified by indexing of selected area diffraction (SAD) pattern. Formation of NbNi intermetallic was evident from XRD pattern and SEM micrograph of sintered alloy. Maximum sinterability of 90.8% was achieved in 20 h milled sintered alloy. Hardness and wear study was also conducted to investigate the mechanical behaviour of the sintered product. Hardness of W80Ni10Nb10 alloy reduces with increasing load whereas wear rate increases with increasing load. The evaluated hardness value in the present study for all loads is lower than the literature reported hardness of nanostructured W.

Development of a theory-based questionnaire to assess structure and control in parent feeding (SCPF).

PubMed

Savage, Jennifer S; Rollins, Brandi Y; Kugler, Kari C; Birch, Leann L; Marini, Michele E

2017-01-26

Parents shape children's eating environments and act as powerful socialization agents, impacting young children's behavioral controls of food intake. Most feeding measures assess parents' use of control to manage children's intake of energy dense foods. The Structure and Control in Parent Feeding (SCPF) questionnaire was developed to assess more positive aspects of feeding practices with their young children -setting limits, providing routines-that promote self-regulation, as well as controlling feeding practices. A mixed method approach was used to develop the SCPF. In 2013, cognitive interviews informed the modification, deletion and/or replacement of items. In 2014, the survey was distributed statewide to mothers of toddlers aged 12 to 36 months participating in the Women, Infants, and Children program. In 2016, exploratory factor analyses was conducted to test our theoretical parenting model and content validity and criterion validity were assessed (n = 334). Exploratory factor analysis (EFA) and second-order EFA revealed a 2-factor, 22-item Structure model and a 2-factor, 12-item Control model. Internal consistencies for all factors exceeded 0.70. As predicted, the Structure superfactor was positivity associated with responsiveness, whereas the Control superfactor was positively associated with demandingness on the Caregiver's Feeding Styles Questionnaire. The Structure subscales were also positively associated with mealtime behaviors and Control subscales were positively associated with control-oriented feeding measures from the Control in Parent Feeding Practices questionnaire. The SCPF questionnaire is a reliable tool that can be used to assess aspects of structure- and control-based feeding practices to better understand how parents feed their toddlers.

Improved results for the mass spectrum of N = 1 supersymmetric SU(3) Yang-Mills theory

NASA Astrophysics Data System (ADS)

Ali, Sajid; Bergner, Georg; Gerber, Henning; Giudice, Pietro; Kuberski, Simon; Münster, Gernot; Montvay, István; Piemonte, Stefano; Scior, Philipp

2018-03-01

This talk summarizes the results of the DESY-Münster collaboration for N = 1 supersymmetric Yang-Mills theory with the gauge group SU(3). It is an updated status report with respect to our preliminary data presented at the last conference. In order to control the lattice artefacts we have now considered a clover improved fermion action and different values of the gauge coupling.

Graphite-to-Graphene: Total Conversion.

PubMed

Buzaglo, Matat; Bar, Ilan Pri; Varenik, Maxim; Shunak, Liran; Pevzner, Svetlana; Regev, Oren

2017-02-01

The rush to develop graphene applications mandates mass production of graphene sheets. However, the currently available complex and expensive production technologies are limiting the graphene commercialization. The addition of a protective diluent to graphite during ball-milling is demonstrated to result in a game-changer yield (>90%) of defect-free graphene, whose size is controlled by the milling energy and the diluent type. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mechanically Milled Irregular Zinc Nanoparticles for Printable Bioresorbable Electronics.

PubMed

Mahajan, Bikram K; Yu, Xiaowei; Shou, Wan; Pan, Heng; Huang, Xian

2017-05-01

Bioresorbable electronics is predominantly realized by complex and time-consuming anhydrous fabrication processes. New technology explores printable methods using inks containing micro- or nano-bioresorbable particles (e.g., Zn and Mg). However, these particles have seldom been obtained in the context of bioresorbable electronics using cheap, reliable, and effective approaches with limited study on properties essential to printable electronics. Here, irregular nanocrystalline Zn with controllable sizes and optimized electrical performance is obtained through ball milling approach using polyvinylpyrrolidone (PVP) as a process control agent to stabilize Zn particles and prevent cold welding. Time and PVP dependence of the ball milled particles are studied with systematic characterizations of morphology and composition of the nanoparticles. The results reveal crystallized Zn nanoparticles with a size of ≈34.834 ± 1.76 nm and low surface oxidation. The resulting Zn nanoparticles can be readily printed onto bioresorbable substrates and sintered at room temperature using a photonic sintering approach, leading to a high conductivity of 44 643 S m -1 for printable zinc nanoparticles. The techniques to obtain Zn nanoparticles through ball milling and processing them through photonic sintering may potentially lead to a mass fabrication method for bioresorbable electronics and promote its applications in healthcare, environmental protection, and consumer electronics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Zero Discharge Performance of an Industrial Pilot-Scale Plant Treating Palm Oil Mill Effluent

PubMed Central

Mahmood, Qaisar; Qiu, Jiang-Ping; Li, Yin-Sheng; Chang, Yoon-Seong; Chi, Li-Na; Li, Xu-Dong

2015-01-01

Palm oil is one of the most important agroindustries in Malaysia. Huge quantities of palm oil mill effluent (POME) pose a great threat to aqueous environment due to its very high COD. To make full use of discharged wastes, the integrated “zero discharge” pilot-scale industrial plant comprising “pretreatment-anaerobic and aerobic process-membrane separation” was continuously operated for 1 year. After pretreatment in the oil separator tank, 55.6% of waste oil in raw POME could be recovered and sold and anaerobically digested through 2 AnaEG reactors followed by a dissolved air flotation (DAF); average COD reduced to about 3587 mg/L, and biogas production was 27.65 times POME injection which was used to generate electricity. The aerobic effluent was settled for 3 h or/and treated in MBR which could remove BOD3 (30°C) to less than 20 mg/L as required by Department of Environment of Malaysia. After filtration by UF and RO membrane, all organic compounds and most of the salts were removed; RO permeate could be reused as the boiler feed water. RO concentrate combined with anaerobic surplus sludge could be used as biofertilizer. PMID:25685798

A Study on Micro-Machining Technology for the Machining of NiTi: Five-Axis Micro-Milling and Micro Deep-Hole Drilling

NASA Astrophysics Data System (ADS)

Biermann, D.; Kahleyss, F.; Krebs, E.; Upmeier, T.

2011-07-01

Micro-sized applications are gaining more and more relevance for NiTi-based shape memory alloys (SMA). Different types of micro-machining offer unique possibilities for the manufacturing of NiTi components. The advantage of machining is the low thermal influence on the workpiece. This is important, because the phase transformation temperatures of NiTi SMAs can be changed and the components may need extensive post manufacturing. The article offers a simulation-based approach to optimize five-axis micro-milling processes with respect to the special material properties of NiTi SMA. Especially, the influence of the various tool inclination angles is considered for introducing an intelligent tool inclination optimization algorithm. Furthermore, aspects of micro deep-hole drilling of SMAs are discussed. Tools with diameters as small as 0.5 mm are used. The possible length-to-diameter ratio reaches up to 50. This process offers new possibilities in the manufacturing of microstents. The study concentrates on the influence of the cutting speed, the feed and the tool design on the tool wear and the quality of the drilled holes.

Economics of an ecotourism operation in Belize

NASA Astrophysics Data System (ADS)

Kangas, Patrick; Shave, Mary; Shave, Paul

1995-09-01

The economic inputs and outputs for the Possum Point Biological Station in Belize during 1990 1992 are described to illustrate some aspects of an ecotourism operation. Eight hundred fifty-four people in 59 groups visited Possum Point during the study period to tour rain forests, estuaries, and coral reefs. The economic input to Possum Point from these groups increased from 74,552 in 1990 to 166,268 in 1992. Outputs were for license fees, capital improvements, goods and services, labor, fossil fuels, and development of a historic sugar mill site. An annual donation was also made to a scholarship fund for local Belizean students. The net cash balance of income and outputs changed from negative (-6678) in 1990 to positive (+4811) in 1992, suggesting development of the economic operation. Possum Point meets the economic criteria for ecotourism by feeding back some tourist monies for community and environmental support, particularly donations for the sugar mill site and the scholarship fund. Most of the outputs from Possum Point (about 80%) were retained in the local economy through employment and purchases, which have a positive influence on the local community. We conclude that ecotourism operations, such as Possum Point, offer important sustainable development opportunities for Belize.

Zero discharge performance of an industrial pilot-scale plant treating palm oil mill effluent.

PubMed

Wang, Jin; Mahmood, Qaisar; Qiu, Jiang-Ping; Li, Yin-Sheng; Chang, Yoon-Seong; Chi, Li-Na; Li, Xu-Dong

2015-01-01

Palm oil is one of the most important agroindustries in Malaysia. Huge quantities of palm oil mill effluent (POME) pose a great threat to aqueous environment due to its very high COD. To make full use of discharged wastes, the integrated "zero discharge" pilot-scale industrial plant comprising "pretreatment-anaerobic and aerobic process-membrane separation" was continuously operated for 1 year. After pretreatment in the oil separator tank, 55.6% of waste oil in raw POME could be recovered and sold and anaerobically digested through 2 AnaEG reactors followed by a dissolved air flotation (DAF); average COD reduced to about 3587 mg/L, and biogas production was 27.65 times POME injection which was used to generate electricity. The aerobic effluent was settled for 3 h or/and treated in MBR which could remove BOD3 (30°C) to less than 20 mg/L as required by Department of Environment of Malaysia. After filtration by UF and RO membrane, all organic compounds and most of the salts were removed; RO permeate could be reused as the boiler feed water. RO concentrate combined with anaerobic surplus sludge could be used as biofertilizer.

Uptake of trace elements and radionuclides from uranium mill tailings by four-wing saltbush (Atriplex canescens) and alkali sacaton (Sporobolus airoides). [Radium 226; Uranium; Molybdenum; Selenium; Vanadium; Astatine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dreesen, D.R.; Marple, M.L.

1979-01-01

A greenhouse experiment was performed to determine the uptake of trace elements and radionuclides from uranium mill tailings by native plant species. Four-wing saltbush and alkali sacaton were grown in alkaline tailings covered with soil and in soil alone as controls. The tailings material was highly enriched in Ra-226, Mo, U, Se, V, and As compared with three local soils. The shrub grown in tailings had elevated concentrations of Mo, Se, Ra-226, U, As, and Na compared with the controls. Alkali sacaton contained high concentrations of Mo, Se, Ra-226, and Ni when grown on tailings. Molybdenum and selenium concentrations inmore » plants grown in tailings are above levels reported to be toxic to grazing animals. These results indicate that the bioavailability of Mo and Se in alkaline environments makes these elements among the most hazardous contaminants present in uranium mill wastes.« less

Interactions Forces and the Flow-Induced Coalescence of Drops and Bubbles

NASA Technical Reports Server (NTRS)

Leal, L. Gary; Israelachvili, J.

2004-01-01

In order to accomplish the proposed macroscale experimental goals, we designed and built a pair of miniaturized computer-controlled four-roll mills, similar but much smaller than the 4-roll mill that had been develop earlier in Prof. Leal's group for studies of drop deformation and breakup. This unique experimental facility allows for controlled experiments on the breakup and coalescence of very small drops in the size range of 20-200 micrometers in diameter for a wide variety of flows and under a wide range of flow conditions including time-dependent flows, etc. The small size of this device is necessary for coalescence studies, since coalescence occurs in viscous fluids at capillary numbers that are large enough to be experimentally accessible only for drops that are smaller than approximately 100_m in diameter. Using these miniaturized 4-roll mills, we have obtained the first quantitative data (so far as we are aware) on the flow-induced coalescence process.

The relationship between milling a new silica-doped zirconia and its resistance to low-temperature degradation (LTD): a pilot study.

PubMed

Nakamura, Takashi; Usami, Hirofumi; Ohnishi, Hiroshi; Nishida, Hisataka; Tang, Xuehua; Wakabayashi, Kazumichi; Sekino, Tohru; Yatani, Hirofumi

2012-02-03

The aim of this study was to determine the machinability of new silica-doped Y-TZP by CAD/CAM and the resistance to low temperature degradation of the milled sample by comparing with a commercial HIP type Y-TZP material. The copings could be milled from silica-doped Y-TZP blocks without chipping, and there was no significant difference between the two types of Y-TZP materials in either the marginal or the inner gap between the abutment and the coping. After aging, the monoclinic content in the commercial Y-TZP copings increased from 25% before testing to 65%, while that of silica-doped Y-TZP copings slightly increased from 23% to 30%. The silica-doped Y-TZP copings did not have any significant difference in fracture load in a comparison between the control group and the aging group, while the commercial Y-TZP copings had a significantly lower fracture load for the aging group than for the control group.

A Simple Flight Mill for the Study of Tethered Flight in Insects.

PubMed

Attisano, Alfredo; Murphy, James T; Vickers, Andrew; Moore, Patricia J

2015-12-10

Flight in insects can be long-range migratory flights, intermediate-range dispersal flights, or short-range host-seeking flights. Previous studies have shown that flight mills are valuable tools for the experimental study of insect flight behavior, allowing researchers to examine how factors such as age, host plants, or population source can influence an insects' propensity to disperse. Flight mills allow researchers to measure components of flight such as speed and distance flown. Lack of detailed information about how to build such a device can make their construction appear to be prohibitively complex. We present a simple and relatively inexpensive flight mill for the study of tethered flight in insects. Experimental insects can be tethered with non-toxic adhesives and revolve around an axis by means of a very low friction magnetic bearing. The mill is designed for the study of flight in controlled conditions as it can be used inside an incubator or environmental chamber. The strongest points are the very simple electronic circuitry, the design that allows sixteen insects to fly simultaneously allowing the collection and analysis of a large number of samples in a short time and the potential to use the device in a very limited workspace. This design is extremely flexible, and we have adjusted the mill to accommodate different species of insects of various sizes.

Associations of parental feeding styles with child snacking behaviour and weight in the context of general parenting.

PubMed

Rodenburg, Gerda; Kremers, Stef P J; Oenema, Anke; van de Mheen, Dike

2014-05-01

To examine cross-sectional and longitudinal (one-year follow-up) associations of parental feeding styles with child snacking behaviour and weight in the context of general parenting, taking into account the multidimensionality of the controlling feeding style. Linear regression analyses were performed. Parents completed a questionnaire to measure five feeding style dimensions (Instrumental Feeding, Emotional Feeding, Encouragement, Overt Control and Covert Control) and children's fruit, energy-dense snack and sugar-sweetened beverage (SSB) intakes. Children's height and weight were measured to calculate their BMI Z-scores. Moderation by parenting style was tested by adding interaction terms to the regression analyses. Observational study in the Netherlands. Parent-child dyads (n 1275) participating in the INPACT (IVO Nutrition and Physical Activity Child cohorT) study; children were (on average) 9 years of age. Instrumental Feeding and Emotional Feeding were negatively related to child fruit intake one year later and positively to (changes in) child energy-dense snack intake. Encouragement was negatively related to child energy-dense snacking and SSB intake one year later. Overt Control was cross-sectionally and prospectively related to (changes in) child energy-dense snacking and SSB intake in a negative direction. Covert Control showed similar associations with child energy-dense snacking and SSB intake as Overt Control. Although Covert Control was also positively related to child fruit intake and (changes in) child BMI Z-score, bootstrapping analyses revealed only a differential effect of Overt Control and Covert Control on child BMI Z-score one year later, with Covert Control displaying a stronger, positive association. Moderation analyses showed that some significant associations between parental feeding styles and outcome measures were dependent on the degree of psychological control and behavioural control. Instrumental Feeding and Emotional Feeding may have a detrimental impact on children's snacking behaviour, while Encouragement, Overt Control and Covert Control may lead to less energy-dense snacking and less SSB intake. Overt Control and Covert Control have differential effects on child BMI Z-score one year later, which supports the idea that they should be treated as separate constructs. Prospective studies with a longer follow-up may elucidate the causal pathways between the various feeding styles and children's snacking behaviour and weight, as well as the moderating influences of psychological and behavioural control.

Submicron particle monitoring of paving and related road construction operations.

PubMed

Freund, Alice; Zuckerman, Norman; Baum, Lisa; Milek, Debra

2012-01-01

This study identified activities and sources that contribute to ultrafine and other submicron particle exposure that could trigger respiratory symptoms in highway repair workers. Submicron particle monitoring was conducted for paving, milling, and pothole repair operations in a major metropolitan area where several highway repair workers were identified as symptomatic for respiratory illness following exposures at the 2001 World Trade Center disaster site. Exposure assessments were conducted for eight trades involved in road construction using a TSI P-Trak portable condensation particle counter. Direct readings near the workers' breathing zones and observations of activities and potential sources were logged on 7 days on 27 workers using four different models of pavers and two types of millers. Average worker exposure levels ranged from 2 to 3 times background during paving and from 1 to 4 times background during milling. During asphalt paving, average personal exposures to submicron particulates were 25,000-60,000, 28,000-70,000, and 23,000-37,000 particles/ cm(3) for paver operators, screed operators, and rakers, respectively. Average personal exposures during milling were 19,000-111,000, 28,000-81,000, and 19,000 particles/cm(3) for the large miller operators, miller screed operators, and raker, respectively. Personal peak exposures were measured up to 467,000 and 455,000 particles/cm(3) in paving and milling, respectively. Several sources of submicron particles were identified. These included the diesel and electric fired screed heaters; engine exhaust from diesel powered construction vehicles passing by or idling; raking, dumping, and paving of asphalt; exhaust from the hotbox heater; pavement dust or fumes from milling operations, especially when the large miller started and stopped; and secondhand cigarette smoke. To reduce the potential for health effects in workers, over 40 recommendations were made to control exposures, including improved maintenance of paver ventilation systems; diesel fume engineering controls; reduced idling; provision of cabs for the operators; and improved dust suppression systems on the milling machine.

Design of a Computerised Flight Mill Device to Measure the Flight Potential of Different Insects.

PubMed

Martí-Campoy, Antonio; Ávalos, Juan Antonio; Soto, Antonia; Rodríguez-Ballester, Francisco; Martínez-Blay, Victoria; Malumbres, Manuel Pérez

2016-04-07

Several insect species pose a serious threat to different plant species, sometimes becoming a pest that produces significant damage to the landscape, biodiversity, and/or the economy. This is the case of Rhynchophorus ferrugineus Olivier (Coleoptera: Dryophthoridae), Semanotus laurasii Lucas (Coleoptera: Cerambycidae), and Monochamus galloprovincialis Olivier (Coleoptera: Cerambycidae), which have become serious threats to ornamental and productive trees all over the world such as palm trees, cypresses, and pines. Knowledge about their flight potential is very important for designing and applying measures targeted to reduce the negative effects from these pests. Studying the flight capability and behaviour of some insects is difficult due to their small size and the large area wherein they can fly, so we wondered how we could obtain information about their flight capabilities in a controlled environment. The answer came with the design of flight mills. Relevant data about the flight potential of these insects may be recorded and analysed by means of a flight mill. Once an insect is attached to the flight mill, it is able to fly in a circular direction without hitting walls or objects. By adding sensors to the flight mill, it is possible to record the number of revolutions and flight time. This paper presents a full description of a computer monitored flight mill. The description covers both the mechanical and the electronic parts in detail. The mill was designed to easily adapt to the anatomy of different insects and was successfully tested with individuals from three species R. ferrugineus, S. laurasii, and M. galloprovincialis.

Nanocrystalline Nb-Al-Ge mixtures fabricated using wet mechanical milling

NASA Astrophysics Data System (ADS)

Pusceddu, E.; Charlton, S.; Hampshire, D. P.

2008-02-01

An investigation into Nb-Al-Ge mixtures is presented with special attention to the superconducting compounds Nb3(Al1-xGex) with x = 0, 0.3 and 1, which are reported to provide the highest upper critical field values for Nb-based compounds. Wet mechanical milling using copper milling media and distilled water as a process control agent (PCA) was used with the intention of improving the yield, properties and the performance of these materials. Very high yields of nanocrystalline material were achieved but significant copper contamination occurred - confirmed using inductively-coupled-plasma atomic-emission-spectroscopy. Simultaneous thermogravimetric measurements and differential scanning calorimetry were performed on powders milled for up to 20 h with different PCA content, to quantify the work done on the powders. A typical grain size of a few nm was obtained for the Nb-Al-Ge mixtures after several hours milling. Powder ground for 20 h with 5% PCA was processed using a hot isostatic press (HIP) operating at 2000 atm and temperatures up to 750 °C. The room temperature resistivity decreased as the temperature of the HIPing increased. Unfortunately, despite the nanocrystalline microstructure of the powders and the high HIP temperatures, if superconducting material was formed it was below the detection level of resistivity, Ac. susceptibility and SQUID measurements. We conclude that during milling there was widespread contamination of the powders by the PCA so that milling with distilled water as a PCA is not to be recommended for fabricating nanocrystalline Nb3(Al1-xGex) A15 superconducting compounds.

Design of a Computerised Flight Mill Device to Measure the Flight Potential of Different Insects

PubMed Central

Martí-Campoy, Antonio; Ávalos, Juan Antonio; Soto, Antonia; Rodríguez-Ballester, Francisco; Martínez-Blay, Victoria; Malumbres, Manuel Pérez

2016-01-01

Several insect species pose a serious threat to different plant species, sometimes becoming a pest that produces significant damage to the landscape, biodiversity, and/or the economy. This is the case of Rhynchophorus ferrugineus Olivier (Coleoptera: Dryophthoridae), Semanotus laurasii Lucas (Coleoptera: Cerambycidae), and Monochamus galloprovincialis Olivier (Coleoptera: Cerambycidae), which have become serious threats to ornamental and productive trees all over the world such as palm trees, cypresses, and pines. Knowledge about their flight potential is very important for designing and applying measures targeted to reduce the negative effects from these pests. Studying the flight capability and behaviour of some insects is difficult due to their small size and the large area wherein they can fly, so we wondered how we could obtain information about their flight capabilities in a controlled environment. The answer came with the design of flight mills. Relevant data about the flight potential of these insects may be recorded and analysed by means of a flight mill. Once an insect is attached to the flight mill, it is able to fly in a circular direction without hitting walls or objects. By adding sensors to the flight mill, it is possible to record the number of revolutions and flight time. This paper presents a full description of a computer monitored flight mill. The description covers both the mechanical and the electronic parts in detail. The mill was designed to easily adapt to the anatomy of different insects and was successfully tested with individuals from three species R. ferrugineus, S. laurasii, and M. galloprovincialis. PMID:27070600

High-resolution stress measurements for microsystem and semiconductor applications

NASA Astrophysics Data System (ADS)

Vogel, Dietmar; Keller, Juergen; Michel, Bernd

2006-04-01

Research results obtained for local stress determination on micro and nanotechnology components are summarized. It meets the concern of controlling stresses introduced to sensors, MEMS and electronics devices during different micromachining processes. The method bases on deformation measurement options made available inside focused ion beam equipment. Removing locally material by ion beam milling existing stresses / residual stresses lead to deformation fields around the milled feature. Digital image correlation techniques are used to extract deformation values from micrographs captured before and after milling. In the paper, two main milling features have been analyzed - through hole and through slit milling. Analytical solutions for stress release fields of in-plane stresses have been derived and compared to respective experimental findings. Their good agreement allows to settle a method for determination of residual stress values, which is demonstrated for thin membranes manufactured by silicon micro technology. Some emphasis is made on the elimination of main error sources for stress determination, like rigid body object displacements and rotations due to drifts of experimental conditions under FIB imaging. In order to illustrate potential application areas of the method residual stress suppression by ion implantation is evaluated by the method and reported here.

FIB-based measurement of local residual stresses on microsystems

NASA Astrophysics Data System (ADS)

Vogel, Dietmar; Sabate, Neus; Gollhardt, Astrid; Keller, Juergen; Auersperg, Juergen; Michel, Bernd

2006-03-01

The paper comprises research results obtained for stress determination on micro and nanotechnology components. It meets the concern of controlling stresses introduced to sensors, MEMS and electronics devices during different micromachining processes. The method bases on deformation measurement options made available inside focused ion beam equipment. Removing locally material by ion beam milling existing stresses / residual stresses lead to deformation fields around the milled feature. Digital image correlation techniques are used to extract deformation values from micrographs captured before and after milling. In the paper, two main milling features have been analyzed - through hole and through slit milling. Analytical solutions for stress release fields of in-plane stresses have been derived and compared to respective experimental findings. Their good agreement allows to settle a method for determination of residual stress values, which is demonstrated for thin membranes manufactured by silicon micro technology. Some emphasis is made on the elimination of main error sources for stress determination, like rigid body object displacements and rotations due to drifts of experimental conditions under FIB imaging. In order to illustrate potential application areas of the method residual stress suppression by ion implantation is evaluated by the method and reported here.

19. WHEELPIT AREA OF 1814 MILL WHERE JACOB PERKINS BREASTWHEEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. WHEELPIT AREA OF 1814 MILL WHERE JACOB PERKINS BREASTWHEEL WAS INSTALLED AND CONTROLLED BY PAUL MOODY FLYBALL GOVERNOR, LOOKING NORTH, WITH WEST (UPSTREAM) WALL AT LEFT. EXTRA HEAVY LONGITUDINAL BEAMS ORIGINALLY SPANNED WHEELPIT AREA WITHOUT INTERNAL SUPPORTS (METAL COLUMNS IN PHOTO ARE A RECENT ADDITION). EVIDENCE OF HEADRACE ENTRANCE ARCH HAS BEEN OBLITERATED BY CONCRETE RETAINING WALL AT REAR. - Boston Manufacturing Company, 144-190 Moody Street, Waltham, Middlesex County, MA

A 10-Year Evaluation of Prescribed Winter Burns in Uneven-Aged Stands of Pinus taeda L. and P. echinata Mill.: Woody Understorey Vegetation Response

Treesearch

Michael D. Cain

1993-01-01

Abstract.The effects of burning cycles and pine basal area levels were assessed on natural pine regeneration and hardwood development in uneven-aged stands of loblolly andshortleafpines (Pinw taeda L. and P. echinata Mill.). The treatments included an unburned control and prescribed winter burrs at 3-, 6-, and 9-yr intervals. Basal area treatments were 9, 14, 18, and...

Microstructure Engineering in Hot Strip Mills, Part 1 of 2: Integrated mathematical Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.K. Brimacombe; I.V. Samaraseker; E.B. Hawbolt

1998-09-30

This report describes the work of developing an integrated model used to predict the thermal history, deformation, roll forces, microstructural evaluation and mechanical properties of steel strip in a hot-strip mill. This achievement results from a join research effort that is part of the American Iron and Steel Institute's (AISI) Advanced Process Control Program, a collaboration between the U.S. DOE and fifteen North American steel makers.

Real-time pair-feeding of animals

NASA Technical Reports Server (NTRS)

Leon, H. A.; Connolly, J. P.; Hitchman, M. J.; Humbert, J. E.

1972-01-01

Automatic pair-feeding system was developed which immediately dispenses same amount of food to control animal as has been consumed by experimental animal that has free access to food. System consists of: master feeding system; slave feeding station; and control mechanism. Technique performs real time pair-feeding without attendant time lag.

Vermicomposting of Paper Mill Sludge with Eisenia fetida for its Conversion to Nutrient Using Different Seed Materials

NASA Astrophysics Data System (ADS)

Mohan, S. Mariraj

2017-12-01

In this study, it was aimed for effective utilization of paper mill sludge through vermicomposting by varying seed proportion with sp. Eisenia fetida. Nine plastic trays were used for the experimental work including control. Different seed proportions of cow dung and cattle dung were tested. The multiplication of earthworms in terms of number was counted at the end of vermicomposting. The N, K, Ca, Na values of the manure in each vermibin were estimated before and after vermicomposting. In this study, it was concluded that tray A2 which has combination of 75% Cow dung (CD) and 25% Paper Mill Sludge (PMS) provided better nitrogen synthesis and lowering C/N ratio, whereas tray A4 (25%CD + 75% PMS) yielded better Calcium recovery. Both the seed materials were found to be suitable for Potassium recovery. From this study, it was inferred that vermicomposting of paper mill sludge with sp. Eisenia fetida along with seed materials can also solve the problem of disposal of this sludge.

Use of Residual Solids from Pulp and Paper Mills for Enhancing Strength and Durability of Ready-Mixed Concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tarun R. Naik; Yoon-moon Chun; Rudolph N. Kraus

2003-09-18

This research was conducted to establish mixture proportioning and production technologies for ready-mixed concrete containing pulp and paper mill residual solids and to study technical, economical, and performance benefits of using the residual solids in the concrete. Fibrous residuals generated from pulp and paper mills were used, and concrete mixture proportions and productions technologies were first optimized under controlled laboratory conditions. Based on the mixture proportions established in the laboratory, prototype field concrete mixtures were manufactured at a ready-mixed concrete plant. Afterward, a field construction demonstration was held to demonstrate the production and placement of structural-grade cold-weather-resistant concrete containing residualmore » solids.« less

Breastfeeding Is Associated with a Maternal Feeding Style Low in Control from Birth

PubMed Central

Brown, Amy; Lee, Michelle

2013-01-01

Background The influence of maternal child-feeding style upon child weight and eating style for children over the age of twelve months is well established. However there is little empirical evidence examining maternal child-feeding style during milk feeding despite evidence that mothers who breastfeed exert lower levels of control over later diet. The aim of this paper was to examine variation in maternal child-feeding style during the first six months postpartum and to explore associations with mode of milk feeding and infant weight. Methods The Child Feeding Questionnaire (CFQ) is frequently used to measure maternal child-feeding style in preschool children. 390 mothers with an infant aged 0–6 months completed an adapted version of the CFQ to measure maternal child-feeding style during milk feeding. Participants reported breastfeeding duration, infant weight and perceived size. Results Principle components analysis of questionnaire items produced six factors; encouraging feeding, feeding to a routine, limiting intake, concern for weight, monitoring and perceived responsibility. Breastfeeding was associated with lower levels of control compared to formula feeding. Infant birth weight was significantly inversely associated with concern for weight, monitoring and encouraging feeding. Discussion Formula feeding is associated with greater maternal control of child-feeding from birth whilst a lower birth weight is linked to concerns for infant weight and pressure to eat. As early maternal child-feeding relationships may impact negatively upon longer term child weight and eating style, identifying variations in maternal feeding style and understanding the factors that influence this is pertinent. PMID:23382881

Heat rejection sublimator

NASA Technical Reports Server (NTRS)

Dingell, Charles W. (Inventor); Quintana, Clemente E. (Inventor); Le, Suy (Inventor); Clark, Michael R. (Inventor); Cloutier, Robert E. (Inventor); Hafermalz, David Scott (Inventor)

2009-01-01

A sublimator includes a sublimation plate having a thermal element disposed adjacent to a feed water channel and a control point disposed between at least a portion of the thermal element and a large pore substrate. The control point includes a sintered metal material. A method of dissipating heat using a sublimator includes a sublimation plate having a thermal element and a control point. The thermal element is disposed adjacent to a feed water channel and the control point is disposed between at least a portion of the thermal element and a large pore substrate. The method includes controlling a flow rate of feed water to the large pore substrate at the control point and supplying heated coolant to the thermal element. Sublimation occurs in the large pore substrate and the controlling of the flow rate of feed water is independent of time. A sublimator includes a sublimation plate having a thermal element disposed adjacent to a feed water channel and a control point disposed between at least a portion of the thermal element and a large pore substrate. The control point restricts a flow rate of feed water from the feed water channel to the large pore substrate independent of time.

Competition Impacts on Growth of Naturally Regenerated Loblolly Pine Seedlings

Treesearch

Michael D. Cain

1988-01-01

Intrusive competition control was used for 3 years in a nuturally regenerated, even-aged stand of loblolly and shortleaf pines (Pinus taeda L. and P. echinata Mill.) in southern Arkansas. Treatments included: no competition control, woody competition control, herbaceous competition control, and total control of nonpine vegetation...

Early discharge with tube feeding at home for preterm infants is associated with longer duration of breast feeding.

PubMed

Meerlo-Habing, Z E; Kosters-Boes, E A; Klip, H; Brand, P L P

2009-07-01

Mothers of preterm infants are more likely to discontinue breast feeding early than mothers of term infants. We evaluated the effect of early discharge with tube feeding of preterm infants under close supervision by paediatric nurse specialists on the duration of breast feeding. Case-control study. Medium/high-care neonatal unit of a large district general hospital. Preterm infants (<37 weeks' gestational age). Early discharge with tube feeding under close supervision by paediatric nurse specialists or regular follow-up of preterm infants discharged with oral feeding. Duration of breast feeding assessed by telephone interview 6 months after birth. There were 50 preterm infants in the early discharge group and 78 in the control group. Mothers in the early discharge group continued to breast feed longer than mothers in the control group (log rank test, p = 0.028). Four months after discharge, 63% of preterm infants in the control group were fed formula compared to 36% in the early discharge group (95% CI for difference 9% to 43%, p = 0.04). The relative risk of breast feeding cessation 6 months after birth in the early discharge group compared to the control group was 0.63 (95% CI 0.41 to 0.96). After adjustment for smoking, gestational age and birth weight, this relative risk was 0.67 (95% CI 0.43 to 1.05). Close supervision and follow-up by paediatric nurse specialists of preterm infants discharged early with tube feeding appears to increase duration of breast feeding. A randomised controlled trial to confirm these findings is warranted.

7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

Code of Federal Regulations, 2011 CFR

2011-01-01

... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

Size and morphology controlled NiSe nanoparticles as efficient catalyst for the reduction reactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subbarao, Udumula; Marakatti, Vijaykumar S.; Amshumali, Mungalimane K.

Facile and efficient ball milling and polyol methods were employed for the synthesis of nickel selenide (NiSe) nanoparticle. The particle size of the NiSe nanoparticle has been controlled mechanically by varying the ball size in the milling process. The role of the surfactants in the formation of various morphologies was studied. The compounds were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray energy dispersive spectroscopy (EDS). The efficiency of the NiSe nanoparticle as a catalyst was tested for the reduction of para-nitroaniline (PNA) to para-phenyldiamine (PPD) and para-nitrophenol (PNP) to para-aminophenol (PAP)more » using NaBH{sub 4} as the reducing agent. Particle size, morphology and the presence of surfactant played a crucial role in the reduction process. - Graphical abstract: NiSe nanoparticles in different size and morphology were synthesized using facile ball milling and polyol methods. Particle size, morphology and the presence of surfactant in these materials played a crucial role in the hydrogenation of PNA and PNP. - Highlights: • NiSe nanoparticles synthesized using ball milling and solution phase methods. • NiSe nanoparticle is an efficient catalyst for the reduction of PNA and PNP. • NiSe is found to be better than the best reported noble metal catalysts.« less

Design and fabrication of complete dentures using CAD/CAM technology

PubMed Central

Han, Weili; Li, Yanfeng; Zhang, Yue; lv, Yuan; Zhang, Ying; Hu, Ping; Liu, Huanyue; Ma, Zheng; Shen, Yi

2017-01-01

Abstract The aim of the study was to test the feasibility of using commercially available computer-aided design and computer-aided manufacturing (CAD/CAM) technology including 3Shape Dental System 2013 trial version, WIELAND V2.0.049 and WIELAND ZENOTEC T1 milling machine to design and fabricate complete dentures. The modeling process of full denture available in the trial version of 3Shape Dental System 2013 was used to design virtual complete dentures on the basis of 3-dimensional (3D) digital edentulous models generated from the physical models. The virtual complete dentures designed were exported to CAM software of WIELAND V2.0.049. A WIELAND ZENOTEC T1 milling machine controlled by the CAM software was used to fabricate physical dentitions and baseplates by milling acrylic resin composite plates. The physical dentitions were bonded to the corresponding baseplates to form the maxillary and mandibular complete dentures. Virtual complete dentures were successfully designed using the software through several steps including generation of 3D digital edentulous models, model analysis, arrangement of artificial teeth, trimming relief area, and occlusal adjustment. Physical dentitions and baseplates were successfully fabricated according to the designed virtual complete dentures using milling machine controlled by a CAM software. Bonding physical dentitions to the corresponding baseplates generated the final physical complete dentures. Our study demonstrated that complete dentures could be successfully designed and fabricated by using CAD/CAM. PMID:28072686

Detoxification of Olive Mill Wastewater and Bioconversion of Olive Crop Residues into High-Value-Added Biomass by the Choice Edible Mushroom Hericium erinaceus.

PubMed

Koutrotsios, Georgios; Larou, Evangelia; Mountzouris, Konstantinos C; Zervakis, Georgios I

2016-09-01

Environmentally acceptable disposal of olive cultivation residues (e.g., olive prunings; olive pruning residues (OLPR)) and olive mill wastes is of paramount importance since they are generated in huge quantities within a short time. Moreover, olive mill wastewater (OMW) or sludge-like effluents ("alperujo"; two-phase olive mill waste (TPOMW)) are highly biotoxic. Hericium erinaceus is a white-rot fungus which produces choice edible mushrooms on substrates rich in lignocellulosics, and its suitability for the treatment of olive by-products was examined for the first time. Fungal growth resulted in a notable reduction of OMW's pollution parameters (i.e., 65 % decolorization, 47 % total phenolic reduction, and 52 % phytotoxicity decrease) and correlated with laccase and manganese peroxidase activities. Solid-state fermentation of various mixtures of OLPR, TPOMW, and beech sawdust (control) by H. erinaceus qualified OLPR in subsequent cultivation experiments, where it exhibited high mushroom yields and biological efficiency (31 %). Analyses of proximate composition and bioactive compound content revealed that mushrooms deriving from OLPR substrates showed significantly higher crude fat, total glucan, β-glucan, total phenolics, and ferric-reducing antioxidant potential values than the control. H. erinaceus demonstrated the potential to detoxify OMW and bioconvert OLPR into high-quality biomass, and hence, this fungus could be successfully exploited for the treatment of such by-products.

Are different generations of CAD/CAM milling machines capable to produce restorations with similar quality?

PubMed

Roperto, Renato; Assaf, Hussein; Soares-Porto, Thiago; Lang, Lisa; Teich, Sorin

2016-10-01

Different CAD/CAM machines' generation may impact the restoration overall quality. The present study evaluated the marginal fit of CAD/CAM restorations manufactured with different generations of CEREC milling unit systems. Sixteen typodont teeth were divided into two groups (n=8) according to the machine's generation assigned. These are control group (G1): Cerec AC with Bluecam/Cerec 3 milling unit and (G2): Cerec AC with Bluecam/MC XL Premium Package milling unit. Scanning of the preparation were performed and crowns were milled using the Vita Mark II blocks. Blocks were cemented using epoxy glue on the pulpal floor only and finger pressure applied for 1 min. Upon completion of the cementation step, misfits between the restoration and abutment were measured by microphotography and the silicone replica technique using light body silicon material on Mesial (M) and Distal (D) surfaces. Mean and SDs of marginal gaps in micrometers were: G1/M: 94.90 (±38.52), G1/D: 88.53 (±44.87), G2/M: 85.65 (±29.89), G2/D: 95.28 (±28.13). Two-way ANOVA indicated no significant differences among different groups ( P >0.05); surface area ( P >0.05) and the interaction ( P >0.05). Overall, G2 had greater margin gaps than G1, however, without statistical difference ( P >0.05). Difference in milling unit generation did not significantly affect the marginal fit. Marginal gap means were in the range of the clinical acceptance levels for both generations of Cerec milling units, regardless the teeth site area. Key words: CAD/CAM, margin, ceramics.

A study to promote breast feeding in the Helsinki Metropolitan area in Finland.

PubMed

Hannula, Leena S; Kaunonen, Marja E; Puukka, Pauli J

2014-06-01

the aim of this study was to assess the impact of providing intensified support for breast feeding during the perinatal period. a quasi-experimental design with non-equivalent control group. three public maternity hospitals (two study, one control) in the Helsinki Metropolitan area in Finland. a convenience sample of 705 mothers (431 in the intervention group, 274 in the control group). in this study, families in the intervention group had access to intensified breast feeding support from midpregnancy, whereas those in the control group had access to normal care. Intensified support included lectures and workshops to health professionals, and families in the intervention group had access to more intensive support and counselling for breast feeding and a breast feeding outpatient clinic. Additionally, an internet-based intervention was only used in the intervention group, but not in the control group. Mothers in the control group received normal care from the midwifery and nursing professionals who were to continue their work normally. The data were analysed statistically. altogether 705 women participated in the study. In the intervention group (n=431), 76% of the women breast fed exclusively throughout the hospital stay, compared to 66% of the mothers in the control group (n=274). In multivariate analysis, the likelihood of exclusive breast feeding at the time of responding (at hospital discharge or after that at home) was increased by the mother not being treated for an underlying illness or medical problem during pregnancy, being in the intervention group, having normal vaginal childbirth, high breast feeding confidence, positive attitude towards breast feeding, good coping with breast feeding, and 24-hour presence of the infant's father in the ward. the low exclusive breast feeding rates of newborns could be increased by using intensified breast feeding support. Mothers' health problems during pregnancy can decrease exclusive breast feeding. Mothers with health problems or other than normal childbirth should receive extra breast feeding support, and the presence of fathers in the ward should be encouraged. Intensified breast feeding counselling and support helps mothers to breast feed exclusively. This support should be available in a variety of forms, so that mothers can choose the type of support they need. As breast feeding counselling and support is intensified, more mothers succeed with exclusive breast feeding. © 2013 Published by Elsevier Ltd.

Hot mill process parameters impacting on hot mill tertiary scale formation

NASA Astrophysics Data System (ADS)

Kennedy, Jonathan Ian

For high end steel applications surface quality is paramount to deliver a suitable product. A major cause of surface quality issues is from the formation of tertiary scale. The scale formation depends on numerous factors such as thermo-mechanical processing routes, chemical composition, thickness and rolls used. This thesis utilises a collection of data mining techniques to better understand the influence of Hot Mill process parameters on scale formation at Port Talbot Hot Strip Mill in South Wales. The dataset to which these data mining techniques were applied was carefully chosen to reduce process variation. There are several main factors that were considered to minimise this variability including time period, grade and gauge investigated. The following data mining techniques were chosen to investigate this dataset: Partial Least Squares (PLS); Logit Analysis; Principle Component Analysis (PCA); Multinomial Logistical Regression (MLR); Adaptive Neuro Inference Fuzzy Systems (ANFIS). The analysis indicated that the most significant variable for scale formation is the temperature entering the finishing mill. If the temperature is controlled on entering the finishing mill scale will not be formed. Values greater than 1070 °C for the average Roughing Mill and above 1050 °C for the average Crop Shear temperature are considered high, with values greater than this increasing the chance of scale formation. As the temperature increases more scale suppression measures are required to limit scale formation, with high temperatures more likely to generate a greater amount of scale even with fully functional scale suppression systems in place. Chemistry is also a significant factor in scale formation, with Phosphorus being the most significant of the chemistry variables. It is recommended that the chemistry specification for Phosphorus be limited to a maximum value of 0.015 % rather than 0.020 % to limit scale formation. Slabs with higher values should be treated with particular care when being processed through the Hot Mill to limit scale formation.

Exposure to grain dust and microbial components in the Norwegian grain and compound feed industry.

PubMed

Halstensen, Anne Straumfors; Heldal, Kari Kulvik; Wouters, Inge M; Skogstad, Marit; Ellingsen, Dag G; Eduard, Wijnand

2013-11-01

The aim of this study was to extensively characterize grain workers' personal exposure during work in Norwegian grain elevators and compound feed mills, to identify differences in exposures between the workplaces and seasons, and to study the correlations between different microbial components. Samples of airborne dust (n = 166) were collected by full-shift personal sampling during work in 20 grain elevators and compound feed mills during one autumn season and two winter seasons. The personal exposure to grain dust, endotoxins, β-1→3-glucans, bacteria, and fungal spores was quantified. Correlations between dust and microbial components and differences between workplaces and seasons were investigated. Determinants of endotoxin and β-1→3-glucan exposure were evaluated by linear mixed-effect regression modeling. The workers were exposed to an overall geometric mean of 1.0mg m(-3) inhalable grain dust [geometric standard deviation (GSD) = 3.7], 628 endotoxin units m(-3) (GSD = 5.9), 7.4 µg m(-3) of β-1→3-glucan (GSD = 5.6), 21 × 10(4) bacteria m(-3) (GSD = 7.9) and 3.6 × 10(4) fungal spores m(-3) (GSD = 3.4). The grain dust exposure levels were similar across workplaces and seasons, but the microbial content of the grain dust varied substantially between workplaces. Exposure levels of all microbial components were significantly higher in grain elevators compared with all other workplaces. The grain dust exposure was significantly correlated (Pearson's r) with endotoxin (rp = 0.65), β-1→3-glucan (rp = 0.72), bacteria (rp = 0.44) and fungal spore (rp = 0.48) exposure, whereas the explained variances were strongly dependent on the workplace. Bacteria, grain dust, and workplace were important determinants for endotoxin exposure, whereas fungal spores, grain dust, and workplace were important determinants for β-1→3-glucan exposure. Although the workers were exposed to a relatively low mean dust level, the microbial exposure was high. Furthermore, the exposure levels of microbial components varied between workplaces although the dust levels were similar. We therefore recommend that exposure levels at different workplaces should be assessed separately and a task-based assessment should be done for detailed evaluation of efficient dust-reducing measures. The microbial content and knowledge of health effects of the microbial components should be considered in health risk evaluations of these workplaces.

Road Construction Safety Audit for Interstate Reconstruction. Volume 2.

DOT National Transportation Integrated Search

1998-10-01

Traffic control alternatives associated with reconstruction projects on a rural interstate have been investigated in this research. Slab replacement projects, milling/resurfacing projects, and traffic controls in the vicinity of interstate ramps were...

Road Construction Safety Audit for Interstate Reconstruction. Volume 1.

DOT National Transportation Integrated Search

1998-10-01

Traffic control alternatives associated with reconstruction projects on a rural interstate have been investigated in this research. Slab replacement projects, milling/resurfacing projects, and traffic controls in the vicinity of interstate ramps were...

Low level impurities in imported wheat are a likely source of feral transgenic oilseed rape (Brassica napus L.) in Switzerland.

PubMed

Schulze, Juerg; Brodmann, Peter; Oehen, Bernadette; Bagutti, Claudia

2015-11-01

In Switzerland, the cultivation of genetically modified (GM) oilseed rape (Brassica napus L.) and the use of its seeds for food and feed are not permitted. Nevertheless, the GM oilseed rape events GT73, MS8×RF3, MS8 and RF3 have recently been found in the Rhine port of Basel, Switzerland. The sources of GM oilseed rape seeds have been unknown. The main agricultural good being imported at the Rhine port of Basel is wheat and from 2010 to 2013, 19% of all Swiss wheat imports originated from Canada. As over 90% of all oilseed rape grown in Canada is GM, we hypothesised that imports of Canadian wheat may contain low level impurities of GM oilseed rape. Therefore, waste fraction samples gathered during the mechanical cleaning of Canadian wheat from two Swiss grain mills were analysed by separating oilseed rape seeds from waste fraction samples and testing DNA of pooled seeds for the presence of transgenes by real-time PCR. Furthermore, oilseed rape seeds from each grain mill were sown in a germination experiment, and seedling DNA was tested for the presence of transgenes by real-time PCR. GT73, MS8×RF3, MS8 and RF3 oilseed rape was detected among seed samples and seedlings of both grain mills. Based on this data, we projected a mean proportion of 0.005% of oilseed rape in wheat imported from Canada. Besides Canadian wheat, the Rhine port of Basel does not import any other significant amounts of agricultural products from GM oilseed rape producing countries. We therefore conclude that Canadian wheat is the major source of unintended introduction of GM oilseed rape seeds into Switzerland.

High-efficiency cogeneration boiler bagasse-ash geochemistry and mineralogical change effects on the potential reuse in synthetic zeolites, geopolymers, cements, mortars, and concretes.

PubMed

Clark, Malcolm W; Despland, Laure M; Lake, Neal J; Yee, Lachlan H; Anstoetz, Manuela; Arif, Elisabeth; Parr, Jeffery F; Doumit, Philip

2017-04-01

Sugarcane bagasse ash re-utilisation has been advocated as a silica-rich feed for zeolites, pozzolans in cements and concretes, and geopolymers. However, many papers report variable success with the incorporation of such materials in these products as the ash can be inconsistent in nature. Therefore, understanding what variables affect the ash quality in real mills and understanding the processes to characterise ashes is critical in predicting successful ash waste utilisation. This paper investigated sugarcane bagasse ash from three sugar mills (Northern NSW, Australia) where two are used for the co-generation of electricity. Data shows that the burn temperatures of the bagasse in the high-efficiency co-generation boilers are much higher than those reported at the temperature measuring points. Silica polymorph transitions indicate the high burn temperatures of ≈1550 °C, produces ash dominated α -quartz rather than expected α-cristobilite and amorphous silica; although α-cristobilite, and amorphous silica are present. Furthermore, burn temperatures must be ≤1700 °C, because of the absence of lechatelierite where silica fusing and globulisation dominates. Consequently, silica-mineralogy changes deactivate the bagasse ash by reducing silica solubility, thus making bagasse ash utilisation in synthetic zeolites, geopolymers, or a pozzolanic material in mortars and concretes more difficult. For the ashes investigated, use as a filler material in cements and concrete has the greatest potential. Reported mill boiler temperatures discrepancies and the physical characteristics of the ash, highlight the importance of accurate temperature monitoring at the combustion seat if bagasse ash quality is to be prioritised to ensure a usable final ash product.

Monticello Mill Tailings Site, Operable Unit lll, Annual Groundwater Report, May 2015 Through April 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Jason; Smith, Fred

This report provides the annual analysis of water quality restoration progress, cumulative through April 2016, for Operable Unit (OU) III, surface water and groundwater, of the U.S. Department of Energy (DOE) Office of Legacy Management (LM) Monticello Mill Tailings Site (MMTS). The MMTS is a Comprehensive Environmental Response, Compensation, and Liability Act National Priorities List site located in and near the city of Monticello, San Juan County, Utah. MMTS comprises the 110-acre site of a former uranium- and vanadium-ore-processing mill (mill site) and 1700 acres of surrounding private and municipal property. Milling operations generated 2.5 million cubic yards of wastemore » (tailings) from 1942 to 1960. The tailings were impounded at four locations on the mill site. Inorganic constituents in the tailings drained from the impoundments to contaminate local surface water (Montezuma Creek) and groundwater in the underlying alluvial aquifer. Mill tailings dispersed by wind and water also contaminated properties surrounding and downstream of the mill site. Remedial actions to remove and isolate radiologically contaminated soil, sediment, and debris from the former mill site, Operable Unit I (OU I), and surrounding properties (OU II) were completed in 1999 with the encapsulation of the wastes in an engineered repository located on DOE property 1 mile south of the former mill site. This effectively removed the primary source of groundwater contamination; however, contamination of groundwater and surface water remains within OU III at levels that exceed water quality protection standards. Uranium is the primary contaminant of concern (COC). LM implemented monitored natural attenuation with institutional controls as the OU III remedy in 2004. Because groundwater restoration proceeded more slowly than expected and did not meet performance criteria established in the OU III Record of Decision (June 2004), LM implemented a contingency action in 2009 by an Explanation of Significant Difference to include a pump-and­ treat system using a single extraction well and treatment by zero-valent iron (ex situ treatment system). The contingency action was optimized in 2015 with the installation of8 extraction wells and 16 monitoring wells in a focused area of the aquifer, the area of attainment (AOA). Contaminated water is treated by solar evaporation at an existing facility at the LM repository.« less

Livestock feed resources utilization practices in Tanqua-Abergelle district of Tigray, Northern Ethiopia.

PubMed

Gebremariam, Tikabo; Belay, Shumuye

2016-08-01

A study was carried out with the objective to assess the utilization practices of local feed resources. It was implemented in Tanqua-Abergelle district of the Tigray region, Northern Ethiopia. Lemlem and Gera peasant associations (PAs) were selected purposively based on their potentiality in livestock resources and road access for household (HH) interview purpose. Likewise, Sheka-Tekli and Hadinet PAs were chosen for the purpose of focus group discussion (FGD). A total of 60 HHs (30 from each PA) were selected randomly for interview using semi-structured questionnaire. About 16 % of the respondents were female HHs. Two FGDs were held with key informants. The collected data were analyzed using SPSS (2013, version 21) statistical software procedures. The study area is characterized by mixed crop-livestock farming system with high interaction between crop and livestock. Livestock are the mainstay for the farm community with many benefits as sources of draught, meat, milk, income, and manures. Cattle are kept primarily for the purpose of draught power with meat and milk as secondary products, whereas shoats are kept mainly for cash income, manure, meat, and milk. The land holding size per HH was 1.44 ha while the herd size was 4.93 tropical livestock unit (TLU). Almost all the land holding (97 %) is allocated for crop cultivation with lesser for forage production (<1 %) indicating poor attention for fodder harvesting. The cattle herd is composed of local breeds (99 %) with less exotic/crossbred (1 %), indicating that the livestock rearing is practiced using local breed. Crop residues, natural pastures, stubble grazing, hay, and browsing are the main feed resources for animals. The availability and contribution of each feed vary with season and areas. Sorghum stover is the main feed source in the area and followed by maize stover, Eragrostis tef straw, and pulse straws. Crop residues are fed as basal diet with no or less supplementation using local concentrates like Attela and mill by-products. Industrial by-products are rarely used in the livestock feeding system for their high price and less availability. Likewise, improved forages are not widely utilized as feed sources.

Assessment of the best available wastewater management techniques for a textile mill: cost and benefit analysis.

PubMed

Dogan, Bugce; Kerestecioglu, Merih; Yetis, Ulku

2010-01-01

In the present study, several water recovery and end-of-pipe wastewater treatment alternatives were evaluated towards the evaluation of Best Available Techniques (BATs) for the management of wastewaters from a denim textile mill in accordance with the European Union's Integrated Pollution Prevention and Control (IPPC) Directive. For this purpose, an assessment that translates the key environmental aspects into a quantitative measure of environmental performance and also financial analysis was performed for each of the alternatives. The alternatives considered for water recovery from dyeing wastewaters were nanofiltration (NF) with coagulation and/or microfiltration (MF) pre-treatment, ozonation or peroxone and Fenton oxidation. On the other hand, for the end-of-pipe treatment of the mill's mixed wastewater, ozonation, Fenton oxidation, membrane bioreactor (MBR) and activated sludge (AS) process followed by membrane filtration technologies were evaluated. The results have indicated that membrane filtration process with the least environmental impacts is the BAT for water recovery. On the other side, MBR technology has appeared as the BAT for the end-of-pipe treatment of the mill's mixed wastewater. A technical and financial comparison of these two BAT alternatives revealed that water recovery via membrane filtration from dyeing wastewaters is selected as the BAT for the water and wastewater management in the mill.

A Comparative study between MPC and PI controller to control vacuum distillation unit for producing LVGO, MVGO, and HVGO

NASA Astrophysics Data System (ADS)

Wahid, A.; Prasetyo, A. P.

2018-03-01

This study describes the selection of controllers in the vacuum distillation unit (VDU) between a model predictive control (MPC) and a proportional-integral (PI) controller by comparing the integral square error (ISE) values. Design of VDU in this simulation is based on modified Metso Automation Inc. scheme. Controlled variables in this study are feed flow rate, feed temperature, top stage pressure, condenser level, bottom stage temperature, LVGO (light vacuum gas oil), MVGO (medium vacuum gas oil), and HVGO (heavy vacuum gas oil) flow rate. As a result, control performance improvements occurred as using MPC compared to PI controllers, when testing a set-point change, of feed flow rate control, feed temperature, top-stage pressure, bottom-stage temperature and flow rate of LVGO, MVGO, and HVGO, respectively, 36%, 6%, 92%, 53%, 90%, 96% and 88%. Only on condenser level control PI performs much better than the MPC. So PI controller is used for level condenser control. While for the test of disturbance rejection, by changing feed flow rate by 10%, there is improvement of control performance using MPC compared to PI controller on feed temperature control, top-stage pressure, bottom-stage temperature and flow rate LVGO, MVGO and HVGO 0.3%, 0.7%, 14%, 2.7%, 10.6% and 4.3%, respectively.

Sensory Characteristics and Volatile Components of Dry Dog Foods Manufactured with Sorghum Fractions.

PubMed

Donfrancesco, Brizio Di; Koppel, Kadri

2017-06-17

Descriptive sensory analysis and gas chromatography-mass spectrometry (GC-MS) with a modified headspace solid-phase microextraction (SPME) method was performed on three extruded dry dog food diets manufactured with different fractions of red sorghum and a control diet containing corn, brewer's rice, and wheat as a grain source in order to determine the effect of sorghum fractions on dry dog food sensory properties. The aroma compounds and flavor profiles of samples were similar with small differences, such as higher toasted aroma notes, and musty and dusty flavor in the mill-feed sample. A total of 37 compounds were tentatively identified and semi-quantified. Aldehydes were the major group present in the samples. The total volatile concentration was low, reflecting the mild aroma of the samples. Partial least squares regression was performed to identify correlations between sensory characteristics and detected aroma compounds. Possible relationships, such as hexanal and oxidized oil, and broth aromatics were identified. Volatile compounds were also associated with earthy, musty, and meaty aromas and flavor notes. This study showed that extruded dry dog foods manufactured with different red sorghum fractions had similar aroma, flavor, and volatile profiles.

Utilization of Mucuna pruriens whole pods to feed lactating hair ewes.

PubMed

Peniche-Gonzalez, Irina Nadieska; Sarmiento-Franco, Luis Armando; Santos-Ricalde, Ronald Herve

2018-03-27

Twenty nine Pelibuey × Katahdin hair ewes rearing single lamb were used during 42 days of lactation to evaluate the effect of including the Mucuna pruriens whole pods in the diets of lactating ewes on milk production and offspring performance. Animals were distributed at random into three experimental diets: a control diet without Mucuna (M0), and two more diets with the inclusion of 13 (M13) and 26% (M26), of milled pods of Mucuna pruriens, respectively. Dry matter intake, was not significantly different (P > 0.05) among diets. Milk yield (P > 0.05) was 734, 786, and 694 g/day for diets M0, M13, and M26, respectively. Milk fat (P > 0.05), milk protein (P > 0.05), and milk lactose (P > 0.05) did not differ between treatments. Lambs had similar daily weight gain (P > 0.05) among diets (180, 174, and 171 g/day for diets M0, M13, and M26, respectively). Diets with Mucuna whole pods were 5.6 and 12.9% more profitable (M13 and M26, respectively) than control diet. Under the conditions of this work, Mucuna pruriens whole pods can be included up to 26% in the diets of lactating crossbred hair ewes without negatively affecting their productive performance during the first 6 weeks of lactation.

A pharmaco-epidemiological study of antibacterial treatments and bacterial diseases in Norwegian aquaculture from 2011 to 2016.

PubMed

Lillehaug, Atle; Børnes, Christine; Grave, Kari

2018-05-07

The sales and prescription of antibacterials for use in Norwegian fish-farming according to diagnosis, fish species and production stage from 2011 to 2016 are analysed. The study is based on antibacterial sales data from wholesalers, pharmacies and feed mills and on prescription data obtained from a register of all prescriptions of antibacterials used in farmed fish. The results show that the fish-farming industry uses very small volumes of antibacterials. In 2016, a total of 212 kg were sold; the only antibacterial substances sold were florfenicol and oxolinic acid. The total amount corresponded to 0.16 mg kg-1 fish slaughtered, or to approximately 0.14% of the fish produced that year. The majority of prescriptions were for non-specific bacterial infections; as most common diseases are under control by vaccination. Most prescriptions for salmonid fish were during early production stages. However, due to higher biomasses of fish, the highest quantities of antibacterials were prescribed during the seawater production phase of Atlantic salmon Salmo salar. An increasing proportion of the prescriptions was for other species, including cleaner fish used for salmon lice control; in 2016 most prescriptions were for this fish category. Due to the negligible use of antibacterials in Norwegian aquaculture, in particular for on-growers, the risk of development of antimicrobial resistance and its transmission to humans through consumption of fish is considered negligible.

Effect of cellooligosaccharide or synbiotic feeding on growth performance, fecal condition and hormone concentrations in Holstein calves.

PubMed

Hasunuma, Toshiya; Kawashima, Kenji; Nakayama, Hirofumi; Murakami, Toshiaki; Kanagawa, Hiroyuki; Ishii, Takashige; Akiyama, Kiyoshi; Yasuda, Kenji; Terada, Fuminori; Kushibiki, Shiro

2011-08-01

We investigated the effect of cellooligosaccharide (CE) or a combination of dextran and Lactobacillus casei ssp. casei strain JCM1134(T) (synbiotic; SB) feeding on growth performance, fecal condition and hormone concentrations in Holstein calves. Fifty-two female Holstein calves were randomly assigned to three treatment groups: CE feeding group (n = 16), SB feeding group (n = 18), and control group (n = 18). Body weight at 90 days of age, as well as daily body weight gain (DG) and feed efficiency after weaning to 90 days of age were greater (P < 0.05) in the CE feeding group than in the control group. The total fecal score tended to be lower (P < 0.1) in the SB feeding group than in the control group. Plasma insulin concentration was higher (P < 0.05) in the CE feeding group than in the control group at 90 days of age. Our results indicate that CE feeding improved DG and feed efficiency in calves. On the other hand, there was less effect on growth performance and fecal Escherichia coli counts in calves fed SB. 2011 The Authors. Animal Science Journal © 2011 Japanese Society of Animal Science.

PHA Productivity and Yield of Ralstonia eutropha When Intermittently or Continuously Fed a Mixture of Short Chain Fatty Acids

PubMed Central

Chakraborty, Panchali; Muthukumarappan, Kasiviswanathan; Gibbons, William R.

2012-01-01

The research described in this present study was part of a larger effort focused on developing a dual substrate, dual fermentation process to produce Polyhydroxyalkanoate (PHA). The focus of this study was developing and optimizing a strategy for feeding a mixture of SCFAs (simulated ARF) and maximizing PHA production in a cost-effective way. Three different feeding strategies were examined in this study. The substrate evaluated in this study for the growth phase of R. eutropha was condensed corn solubles, a low-value byproduct of the dry-mill, corn ethanol industry. The culture was grown to high cell densities in nitrogen-supplemented condensed corn solubles media in 5 L bioreactors. The overall growth rate of R. eutropha was 0.2 h−1. The 20 mL ARF feeding every 3 h from 48 to 109 h strategy gave the best results in terms of PHA production. PHA productivity (0.0697 g L−1 h−1), PHA concentration (8.37 g L−1), and PHA content (39.52%) were the highest when ARF was fed every 3 h for 61 h. This study proved that condensed corn solubles can be potentially used as a growth medium to boost PHA production by R. eutropha thus reducing the overall cost of biopolymer production. PMID:23118512

Improvement of cement plant dust emission by bag filter system

NASA Astrophysics Data System (ADS)

Wahyu Purnomo, Chandra; Budhijanto, Wiratni; Alfisyah, Muziibu; Triyono

2018-03-01

The limestone quarry in PT Indocement Tunggal Prakarsa (ITP) in Cirebon is considered as a complex quarry in terms of chemical composition and material hardness. From the beginning of the plant operation up to the end of 2015, the dust removal was rely on electrostatic precipitator (EP) system. Whenever limestone from specific quarry zones were incorporated into Raw Mill (RM) feed or there was an upset condition, the dust emission increased significantly. Beside higher demand of electricity, an EP system requires lower gas inlet temperature in order to remove the dust effectively which requires larger cooling water in the previous gas conditioning tower to cool down gas from 400 °C to about 100 °C. By considering the drawbacks, the EP system was replaced by a bag filter (BF) system. The BF allows higher temperature of gas inlet and it has higher dust removal efficiency. In this study, the efficiency of the two different dust removal systems is compared. The effect of process variables i.e. RM feed, kiln feed, inlet temperature and pressure, and small size particle fraction to the dust emission are studied by multivariate linier regression analysis. It is observed that the BF system can reduce significantly the dust emission from 30 to 6 mg/m3 and in the same time reducing CO2 emission by 0.24 ton/year from the electricity consumption saving.

Coal fracturing and heteroatom removal. Annual report, fiscal year 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sapienza, R.; Slegeir, W.; Butcher, T.

1983-09-01

Coal-water slurry fuels offer a practical, economical method to use coal, replacing the 3 million barrels of oil used per day to fuel utility boilers, industrial heaters, and furnaces in the US. The mineral matter and in some cases the costs of grinding are major impediments to the direct use of this fuel in existing fluid fuel combustors. A process for the simultaneous cleaning and fracturing of a variety of coals has been explored at Brookhaven National Laboratory. This process entails exposure of coal to a carbon dioxide-water solvent system under pressure. Substantial amounts of mineral matter are leached intomore » the liquid phase, significantly lowering the concentrations of alkaline, and alkaline earth metals, and of silica- and alumina-like minerals in the coal. Grindability studies have been conducted in a laboratory ball mill using processed coal. Grinding times for large-size feed coal (1-3/8 to 3/8 in.) are reduced by a factor up to 10 following exposure to CO/sub 2//water. With smaller-feed coal (4 x 8 mesh), however, improvements in grindability are much smaller. An integrated system has been constructed in which coal is ground while under CO/sub 2/ pressure. Significant improvements in grindability have been observed with this system, even with smaller-feed coal. 20 refs., 8 figs., 24 tabs.« less

Modelling of End Milling of AA6061-TiCp Metal Matrix Composite

NASA Astrophysics Data System (ADS)

Vijay Kumar, S.; Cheepu, Muralimohan; Venkateswarlu, D.; Asohan, P.; Senthil Kumar, V.

2018-03-01

The metal-matrix composites (MMCs) are used in various applications hence lot of research has been carried out on MMCs. To increase the properties of Albased MMCs many ceramic reinforcements have been identified, among which TiC is played vital role because of its properties like high hardness, stiffness and wear resistance. In the present work, a neural network and statistical modelling approach is going to use for the prediction of surface roughness (Ra) and cutting forces in computerised numerical control milling machine. Experiments conducted on a CNC milling machine based on the full factorial design and resulted data used to train and checking the network performance. The sample prepared from in-situ technique and heat treated to get uniform properties. The ANN model has shown satisfactory performance comparatively.

Modelling of End Milling of AA6061-TiCp Metal Matrix Composite

NASA Astrophysics Data System (ADS)

Vijay Kumar, S.; Cheepu, Muralimohan; Venkateswarlu, D.; Asohan, P.; Senthil Kumar, V.

2018-03-01

The metal-matrix composites (MMCs) are used in various applications hence lot of research has been carried out on MMCs. To increase the properties of Al-based MMCs many ceramic reinforcements have been identified, among which TiC is played vital role because of its properties like high hardness, stiffness and wear resistance. In the present work, a neural network and statistical modelling approach is going to use for the prediction of surface roughness (Ra) and cutting forces in computerised numerical control milling machine. Experiments conducted on a CNC milling machine based on the full factorial design and resulted data used to train and checking the network performance. The sample prepared from in-situ technique and heat treated to get uniform properties. The ANN model has shown satisfactory performance comparatively.

Effectiveness duckweed (Lemna minor) as an alternative native chicken feed native chicken (Gallus domesticus)

NASA Astrophysics Data System (ADS)

Putra, A.; Ritonga, M. Z.

2018-02-01

This study aimed to know the effectiveness duckweed as feed as native chicken (Gallus domesticus) on growth period (weight gain, feed intake and feed conversion). This research was conducted in Desa Telaga Jernih Kabupaten Langkat. The study was conducted in February 2017 until May 2017. This study use completely randomized design (CRD) with 4 treatments and 5 Replication, where each treatment consisting of 5 Native chickens unsexing. The treatment was used P0 = control (feed manufacturing), P1 = ration conventional with 10% duckweed, P2 = ration conventional with 20% duckweed, P3 = ration conventional with 30% duckweed. The parameters observed were weight gain, feed consumption and feed conversion. The results showed not significantly effect in body weight gain, feed consumption and feed conversion. Where the average of best weight gain on treatment P0 (control), P2 (20% duckweed), P3 (30% duckweed) and P1 (10% duckweed), average of best feed consumption in P0 (control), P2 (20% duckweed ) Of P1 (10% duckweed) and P3 (30% duckweed), P1 (10% duckweed) and P3 (30% duckweed), average of best feed conversion rate in P0 (control), P2 (20% duckweed) P1 (10% duckweed) and P3 (30% duckweed).

Effects of prescribed fire and other plant community restoration treatments on tree mortality, bark beetles, and other saproxylic coleoptera of longleaf pine, Pinus palustris Mill., on the coastal plain of Alabama

Treesearch

Joshua W. Campbell; James L. Hanula; Kenneth W. Outcalt

2008-01-01

Treatments to restore understory plant communities of mature (50-80-year old) longleaf pine (Pinus palustris Mill.) and reduce risks of wildfire were applied to 10 ha plots that had a substantial shrub layer due to lack of fire. Plots were located in the Coastal Plain of Alabama and treatments consisted of: (1) untreated control, (2) growing season...

Multiscale Monte Carlo equilibration: Pure Yang-Mills theory

DOE PAGES

Endres, Michael G.; Brower, Richard C.; Orginos, Kostas; ...

2015-12-29

In this study, we present a multiscale thermalization algorithm for lattice gauge theory, which enables efficient parallel generation of uncorrelated gauge field configurations. The algorithm combines standard Monte Carlo techniques with ideas drawn from real space renormalization group and multigrid methods. We demonstrate the viability of the algorithm for pure Yang-Mills gauge theory for both heat bath and hybrid Monte Carlo evolution, and show that it ameliorates the problem of topological freezing up to controllable lattice spacing artifacts.

National Program for Inspection of Non-Federal Dams. Knox Mill Dam (ME 00276), Megunticook River Basin, Camden, Maine. Phase I Inspection Report.

DTIC Science & Technology

1978-08-01

been furnished the owner, Camden Water & Power Co., 33 Mechanic Street, ..... a ine 0,-43. Co-ies of this report will be made available to the public...gn Branch Engineering Division SAUL CO ER, Member Chief, Water Control Branch Engineering Division APPROVAL RECOMMENDED: JOE B. FRYAR Chief...Camden Water & Power Co. 33 Mechanic Street Camden, Maine 04843 Tne Camden Water and Power Company is an affiliate of Knox Woolen Mills Company. f

Description of Manufacture - Optical Elements for Five Control Instruments

DTIC Science & Technology

1951-04-01

the rotation of the mill. Pressure is applied at each turning point. When the abrasive on the mill is spent (i.e., has lost its catting efficiency...in hot water or by soaking, first in kerosene, then in alcohol. Shellac is removed by soaking in alcohol or in a dilute caustic bath, and other...room tempera- tures, the solutions are spent in just 10 min- utes. At the end of this time the residual solution is poured out and the dish is

Comparative study of lung functions in women working in different fibre industries.

PubMed

Khanam, F; Islam, N; Hai, M A

2008-07-01

A cross sectional work has been done on Bangladeshi females, working in different fibre industries, to study the effect of exposure to fibre dust on pulmonary functions. The ventilatory capacities were measured by VMI ventilometer in 653 apparently healthy women (160, 162 and 167 were jute, textile and garment industry workers, respectively). For the controls 164 females were recruited who never worked in any fibre industry. The observed FVC, FEV1 and PEFR were lower in all groups of fibre industry workers than those of the control. Among the industry workers, the jute mill workers had the lowest ventilatory capacities and garment industry workers had the highest values. The jute and textile mill workers had also significantly lower FEV1 and PEFR than those of garment industry workers. The FEV1 and PEFR were significantly lower in jute mill workers than those of textile ill workers. The low ventilatory capacities were almost proportionate with the length of service of the workers. Thus, the present study indicates that the fibre dust, on regular exposure for longer duration, may limit the lung functions.

Residential proximity to industrial sites in the area of Taranto (Southern Italy). A case-control cancer incidence study.

PubMed

Marinaccio, Alessandro; Belli, Stefano; Binazzi, Alessandra; Scarselli, Alberto; Massari, Stefania; Bruni, Antonella; Conversano, Michele; Crosignani, Paolo; Minerba, Aldo; Zona, Amerigo; Comba, Pietro

2011-01-01

The association between cancer incidence and the residence near polluting facilities in an industrial area nearby Taranto has been investigated. Age, sex and occupational exposure were controlled as confounding variables in a case-control study (658 cases, 2092 controls). High risks were evidenced close to the steel mill (OR: 3.54), coke plant (OR: 4.80), mineral deposit (OR: 3.33) and shipbuilding (OR: 4.29) for pleural neoplasm, and to the steel mill (OR: 1.65) and shipbuilding (OR: 1.79) for lung cancer. After adjustment for occupational exposure, increasing trends of risk were observed both for lung and bladder cancers. Cancer risks were evidenced near industrial sites and the introduction of "occupational exposure" as a confounder modified significantly the risks with respect to distance from the source of pollution, particularly for pleural, lung and bladder cancers.

31. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill: oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill: one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: View down at the mill from top of the mill's circular masonry enclosure. Mill animals circling above the mill, on top of the enclosure, dragged booms radiating from the drive shaft to power the mill. The drive-shaft is no longer in its upright positon but is lying next to the mill in the foreground. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Breast feeding, bottle feeding, and maternal autonomic responses to stress.

PubMed

Mezzacappa, Elizabeth Sibolboro; Kelsey, Robert M; Katkin, Edward S

2005-04-01

The aim of this study was to examine the effects of breast feeding on autonomic nervous system (ANS) response to stressors. Sympathetic and parasympathetic activities were examined before, during, and after standard laboratory stressors in women who were either exclusively breast feeding (n=14) or nonexclusively breast feeding (n=14), and in non-postpartum controls (n=15). Mothers who breast fed exclusively showed greater levels of parasympathetic cardiac modulation and slower heart rate (HR) throughout the session and less HR increase and preejection period (PEP) shortening to mental arithmetic (MA) than did nonexclusive breast feeders and controls. Nonexclusive breast-feeders showed greater electrodermal reactivity to, and greater differences in skin conductance response (SCR) frequency between baseline and recovery from cold pressor (CP) than did either exclusive breast-feeders or controls. Sympathetic activity was negatively related to the number of breast feedings and positively related to bottle feedings. Breast feeding shifts maternal ANS balance toward relatively greater parasympathetic and lesser sympathetic activity; the opposite occurs with bottle feeding. The frequency of feeding also is a critical factor in determining breast feeding effects on maternal ANS function.

Ecotoxicological studies with newly hatched larvae of Concholepas concholepas (Mollusca, Gastropoda): bioassay with secondary-treated kraft pulp mill effluents.

PubMed

Manríquez, Patricio H; Llanos-Rivera, Alejandra; Galaz, Sylvana; Camaño, Andrés

2013-12-01

The Chilean abalone or "loco" (Concholepas concholepas, Bruguière 1789) represent the most economically important marine recourse exploited from inner inshore Management and Exploitation Areas for Benthic Resources along the Chilean coast. In this study, newly-hatched larvae of C. concholepas were investigated as a potential model species for marine ecotoxicological studies. The study developed a behavioral standard protocol for assessing the impact that kraft pulp mill effluents after secondary treatment have on C. concholepas larvae. Under controlled laboratory conditions, newly-hatched larvae were exposed to a series of different concentrations of kraft pulp mill effluents with secondary treatment (Pinus spp. and Eucalyptus spp.), potassium dichromate as standard reference toxicant and effluent-free control conditions. Regardless of the type of effluent the results indicated that diluted kraft pulp effluent with secondary treatment had reduced effect on larval survival. Low larval survivals were only recorded when they were exposed to high concentrations of the reference toxicant. This suggests that C. concholepas larval bioassay is a simple method for monitoring the effects of kraft pulp mill effluents with secondary treatment discharged into the sea. The results indicated that dilution of ca. 1% of the effluent with an elemental chlorine free (ECF) secondary treatment is appropriate for achieving low larval mortalities, such as those obtained under control conditions with filtered seawater, and to minimize their impact on early ontogenetic stages of marine invertebrates such as newly-hatched larvae of C. concholepas. The methodological aspects of toxicological testing and behavioral responses described here with newly-hatched larvae of C. concholepas can be used to evaluate in the future the potential effects of other stressful conditions as other pollutants or changes in seawater pH associated with ocean acidification. © 2013 Elsevier Inc. All rights reserved.

FEEDING THE CHILD WITH A HANDICAP.

ERIC Educational Resources Information Center

DAMON, ALICE A.; AND OTHERS

SUGGESTIONS ON MEETING NUTRITIONAL AND FEEDING SKILL NEEDS OF HANDICAPPED CHILDREN ARE PRESENTED FOR PARENTS. PRINCIPLES OF GROWTH AND DEVELOPMENT COMMON TO ALL CHILDREN AND THE EFFECT THIS DEVELOPMENT HAS ON FEEDING ARE DISCUSSED. INSTRUCTIONS ARE GIVEN FOR ENCOURAGING CONTROL OF SWALLOWING, SUCKING, TONGUE CONTROL, CHEWING, AND SELF-FEEDING.…

Studies on rye (Secale cereale L.) lines exhibiting a range of extract viscosities. 2. Rheological and baking characteristics of rye and rye/wheat blends and feeding value for chicks of wholemeals and breads.

PubMed

Ragaee, S M; Campbell, G L; Scoles, G J; McLeod, J G; Tyler, R T

2001-05-01

Five rye lines exhibiting a wide range of extract viscosities were evaluated for the rheological and baking properties of their flours, individually and in blends with hard red spring wheat flour. Commercial cultivars of rye and triticale were included in the study as controls. Extract viscosities of rye flours were higher than those of corresponding wholemeals, indicating shifting of water-extractable arabinoxylan into flour during roller milling. Falling numbers of the rye flours correlated positively with their extract viscosities in the presence (r = 0.73, p < 0.05) or absence (r = 0.65, p < 0.05) of an enzyme inhibitor. Farinograms revealed the weakness of rye and triticale flours compared to wheat flour. Extract viscosities of rye flours were negatively correlated (r = -0.65, p < 0.05) with mixing tolerance index and positively correlated (r = 0.64, p < 0.05) with dough stability, suggesting a positive impact of extract viscosity on dough strength. Extract viscosity was negatively correlated (r = -0.74, p < 0.05) with loaf volume and specific volume (r = -0.73, p < 0.05) and positively correlated (r = 0.73, p < 0.05) with loaf weight of rye/wheat bread. Overall, the results indicated that 30% of flour from high or low extract viscosity rye could be incorporated into rye/wheat breads without seriously compromising bread quality. Inclusion of rye, particularly high extract viscosity rye, in chick diets seriously impeded growth performance and feed efficiency. Part of the arabinoxylan survived bread-making and exerted an effect on chicks, although substantially lower digesta viscosities were observed in chicks fed rye bread diets than in those fed rye wholemeals.

Transmission and control of Salmonella in the pig feed chain: a conceptual model.

PubMed

Binter, Claudia; Straver, Judith Maria; Häggblom, Per; Bruggeman, Geert; Lindqvist, Per-Anders; Zentek, Jürgen; Andersson, Mats Gunnar

2011-03-01

Infected breeder pigs and contaminated feed represent potential sources of Salmonella introduction to fattening pig herds and may thereby cause human infections acquired via consumption of contaminated pork. Modelling approaches such as quantitative microbial risk assessment could improve the design of strategies for control and tracing of Salmonella in the feed chain. However, the construction of such models requires a thorough understanding of the dynamics of the feed chain, including production processes, microbial processes and transport logistics. The present article illustrates a conceptual model of Salmonella in the pig feed chain and explores the possibilities for quantitative modelling including identifying major gaps in data. Information was collected from peer-reviewed scientific journals, official documents and reports and by means of interviews with experts from authorities and the feed industry. Data on prevalence of Salmonella in different parts of the feed chain are difficult to compare as observed prevalence may be biased by variations in sampling procedures as well as limitations of the detection methods. There are almost no data on numbers of Salmonella in commodities of the feed chain, which often makes it difficult to evaluate risks, intervention strategies and sampling plans in a quantitative manner. Tracing the source of Salmonella contamination is hampered by the risk of cross-contamination as well as various mixing and partitioning events along the supply chain, which sometimes makes it impossible to trace the origin of a lot back to a batch or producer. Available information points to contaminated feed materials, animal vectors and persistent contamination of production environments as important sources of Salmonella in feed production. Technological procedures such as hydrothermal or acid treatment can be used to control Salmonella in feed production. However, a large fraction of pig feed is produced without decontamination procedures. Prevention of recontamination and control of moisture throughout the chain are thus critical factors for controlling Salmonella in feed production. To verify successful control it is necessary to have monitoring strategies able to detect low levels of Salmonella heterogeneously distributed in large volumes of feed and feed material in bulk. Experience from monitoring programs and research investigations indicates that sampling of dust and sweepings from control points along the production line is an efficient strategy to gain an indication of Salmonella contamination. Copyright © 2010 Elsevier B.V. All rights reserved.

A modified milling system, using a bimodal distribution of highly resistant ceramics. Part 1. A natural hydroxyapatite study.

PubMed

Harabi, Abdelhamid; Harabi, Esma

2015-06-01

A careful combination of the main parameters controlling natural hydroxyapatite (NHA: Ca10(PO4)6(OH)2) production such as milling techniques, sintering temperature and holding time may lead to an interesting NHA based bio-ceramics without any foreign oxide additions. In this way, an original wet milling setup has been proposed to obtain sub-micron sized NHA powders. In order to avoid any possible NHA decomposition, a precise Ca/P ratio of NHA derived from animals was selected accordingly. Also, an alternative direct visual approach of the bone age classification was also proposed. A relative density of about 95% was obtained for powders sintered at 1300°C for 2h. The best Vickers micro-hardness and 3 point bending strength values for these sintered samples, using this proposed milling system and without any additions, were 4.7±0.3GPa and 37MPa, respectively. Finally, a complete correlation between the powder microstructure and the final product properties has been established. Copyright © 2015 Elsevier B.V. All rights reserved.

Analysis and pollution sources speculations of toxic gases in a secondary fiber paper mill.

PubMed

Tong, Xin; Liu, Zhang; Chen, Xiao Q; Shen, Wen H

2016-11-09

This paper quantitatively investigates the compositions of the gaseous pollutants in the ambient air of a secondary fiber paper mill. Total volatile organic compounds (TVOC), formaldehyde (HCHO), sulfur compounds (H2S), and hydrocarbon compounds (CxHy) were analyzed on six sampling sites with photo-ionisation detector, acetylacetone spectrophotometric method, and gas detector. The results revealed that, the high levels of TVOC and CxHy were detected at the wet end of paper machine and the office area, respectively; all the H2S contents on the six sites exceeded the limit (0.06 mg m(-3)) seriously; the HCHO concentrations at other five sites were out of the limit (0.10 mg m(-3)) except for the wastewater treatment plant. Furthermore, the necessary discussions about the possible pollution sources were considered on the process flow, the chemical agents used, and the ambient conditions in the paper mill. For the sake of air pollution control in paper mills, these remarkable results and analysis lay some technical basis in the following researches that should attract more attentions.

Experimental evaluation of tool run-out in micro milling

NASA Astrophysics Data System (ADS)

Attanasio, Aldo; Ceretti, Elisabetta

2018-05-01

This paper deals with micro milling cutting process focusing the attention on tool run-out measurement. In fact, among the effects of the scale reduction from macro to micro (i.e., size effects) tool run-out plays an important role. This research is aimed at developing an easy and reliable method to measure tool run-out in micro milling based on experimental tests and an analytical model. From an Industry 4.0 perspective this measuring strategy can be integrated into an adaptive system for controlling cutting forces, with the objective of improving the production quality, the process stability, reducing at the same time the tool wear and the machining costs. The proposed procedure estimates the tool run-out parameters from the tool diameter, the channel width, and the phase angle between the cutting edges. The cutting edge phase measurement is based on the force signal analysis. The developed procedure has been tested on data coming from micro milling experimental tests performed on a Ti6Al4V sample. The results showed that the developed procedure can be successfully used for tool run-out estimation.