Utilizing hydrologic, statistical, and geochemical tools to assess uranium mobility in surface and near-surface environments

NASA Astrophysics Data System (ADS)

Naftz, D. L.; Walton-Day, K. E.; Fuller, C.; Dam, W. L.; Briggs, M. A.; Snyder, T.

2015-12-01

Legacy uranium (U) mining and processing activities have resulted in soil and water contamination on Federal, state, and tribal lands in the western United States. Sites include legacy mill sites associated with U extraction now managed by the Department of Energy and thousands of waste dumps associated with U exploration, mining, and processing. Recently (2012), over 400,000 hectares of federally managed land in northern Arizona was withdrawn from consideration of mining for a 20-year period to protect the Grand Canyon watershed from potentially adverse effects of U mineral exploration and development. Ore from active and recently active U mines in the Colorado Plateau, the Henry Mountains Complex, and the Arizona Strip is transported to the only currently (2015) active conventional mill site in the western United States, located in Utah. Previous and ongoing U.S. Geological Survey assessments to examine U mobility at a variety of legacy and active sites associated with ore exploration, extraction, and processing will be presented as field-scale examples. Topics associated with site investigations will include: (1) offsite migration of radionuclides associated with the operation of the White Mesa U mill; (2) long-term contaminant transport from legacy U waste dumps on Bureau of Land Management regulated land in Utah; (3) application of incremental soil sampling techniques to determine pre- and post-mining radionuclide levels associated with planned and operating U mines in northern Arizona; (4) application of fiber optic digital temperature sensing equipment to identify areas where shallow groundwater containing elevated U levels may be discharging to a river adjacent to a reclaimed mill site in central Wyoming; and (5) field-scale manipulation of groundwater chemistry to limit U migration from a legacy upgrader site in southeastern Utah.

Effect of effluent from a nitrogen fertilizer factory and a pulp mill on the distribution and abundance of Aeromonas hydrophila in Albemarle Sound, North Carolina.

PubMed Central

Hazen, T C; Esch, G W

1983-01-01

The density of Aeromonas hydrophila, standard count bacteria, fecal coliform bacteria, and 18 physical and chemical parameters were measured simultaneously at six sites for 12 months in Albemarle Sound, N.C. One site was above and two sites were below the discharge plume of a Kraft pulping process paper mill. The fourth site was above and the remaining two sites were below the discharge point of a nitrogen fertilizer factory. The impact of the pulp mill on water quality was acute, whereas that of the nitrogen fertilizer factory was chronic and much more subtle. Diffusion chamber studies indicated that A. hydrophila survival is increased by pulp mill effluent and decreased by nitrogen fertilizer factory effluent. From correlation and regression analysis, A. hydrophila was found to be directly affected by phytoplankton density and, thus, indirectly by concentrations of phosphate, nitrate, and total organic carbon. These two point sources are suspect as indirect causes of red-sore disease epizootics, a disease of fish caused by A. hydrophila. PMID:6297393

Technical approaches to characterizing and cleaning up iron and steel mill sites under the brownfields initiative. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

EPA has developed this guide to provide decision-makers, such as city planners, private sector developers, and other involved in redeveloping brownfields, with a better understanding of the technical issues involved in assessing and cleaning up iron and steel mill sites so they can make the most informed decisions possible. This overview of the technical process involved in assessing and cleaning up brownfields sites can assist planners in making decisions at various stages of the project. An understanding of land use and industrial processes conducted in the past at a site can help the planner to conceptualize the site and identifymore » likely areas of contamination that may require cleanup. Numerous resources are suggested to facilitate characterization of the site and consideration of cleanup technologies.« less

Assessment of a Hydroxyapatite Permeable Reactive Barrier to Remediate Uranium at the Old Rifle Site Colorado.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Robert C.; Szecsody, James; Rigali, Mark J.

We have performed an initial evaluation and testing program to assess the effectiveness of a hydroxyapatite (Ca10(PO4)6(OH)2) permeable reactive barrier and source area treatment to decrease uranium mobility at the Department of Energy (DOE) former Old Rifle uranium mill processing site in Rifle, western Colorado. Uranium ore was processed at the site from the 1940s to the 1970s. The mill facilities at the site as well as the uranium mill tailings previously stored there have all been removed. Groundwater in the alluvial aquifer beneath the site still contains elevated concentrations of uranium, and is currently used for field tests tomore » study uranium behavior in groundwater and investigate potential uranium remediation technologies. The technology investigated in this work is based on in situ formation of apatite in sediment to create a subsurface apatite PRB and also for source area treatment. The process is based on injecting a solution containing calcium citrate and sodium into the subsurface for constructing the PRB within the uranium plume. As the indigenous sediment micro-organisms biodegrade the injected citrate, the calcium is released and reacts with the phosphate to form hydroxyapatite (precipitate). This paper reports on proof-of-principle column tests with Old Rifle sediment and synthetic groundwater.« less

Superfund Record of Decision (EPA Region 1): Stamina Mills site, North Smithfield, RI. (First remedial action), September 1990. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-09-28

The five-acre Stamina Mills site is a former textile weaving and finishing facility in North Smithfield, Providence County, Rhode Island. A portion of the site is within the 100-year floodplain and wetland area of the Branch River. The manufacturing process used cleaning solvents, acids, bases and dyes for coloring, pesticides for moth proofing, and plasticizers to coat fabrics. Mill process wastes were placed in a landfill onsite. EPA initiated three removal actions from 1984 to 1990, including an extension of the municipal water supply to residents obtaining water from the affected aquifer; and treatment of two underground and one above-groundmore » storage tanks, followed by offsite disposal. The Record of Decision (ROD) provides a final remedy and addresses both source control and management of contaminated ground water migration at the site. The primary contaminants of concern affecting the soil, debris, sediment, and ground water are VOCs including TCE and PCE; other organics including pesticides; and metals including chromium.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dam, William; Campbell, Sam; Johnson, Ray

Milling activities at a former uranium mill site near Riverton, Wyoming, USA, contaminated the shallow groundwater beneath and downgradient of the site. Although the mill operated for <6 years (1958-1963), its impact remains an environmental liability. Groundwater modeling predicted that contaminant concentrations were declining steadily, which confirmed the conceptual site model (CSM). However, local flooding in 2010 mobilized contaminants that migrated downgradient from the Riverton site and resulted in a dramatic increase in groundwater contaminant concentrations. This observation indicated that the original CSM was inadequate to explain site conditions and needed to be refined. In response to the new observationsmore » after the flood, a collaborative investigation to better understand site conditions and processes commenced. This investigation included installing 103 boreholes to collect soil and groundwater samples, sampling and analysis of evaporite minerals along the bank of the Little Wind River, an analysis of evaportranspiration in the shallow aquifer, and sampling naturally organic-rich sediments near groundwater discharge areas. The enhanced characterization revealed that the existing CSM did not account for high uranium concentrations in groundwater remaining on the former mill site and groundwater plume stagnation near the Little Wind River. Observations from the flood and subsequent investigations indicate that additional characterization is still needed to continue refining the CSM and determine the viability of the natural flushing compliance strategy. Additional sampling, analysis, and testing of soil and groundwater are necessary to investigate secondary contaminant sources, mobilization of contaminants during floods, geochemical processes, contaminant plume stagnation, distribution of evaporite minerals and organic-rich sediments, and mechanisms and rates of contaminant transfer from soil to groundwater. Future data collection will be used to continually revise the CSM and evaluate the compliance strategy at the site.« less

75 FR 8346 - Proposed CERCLA Administrative Settlement; Anderson-Calhoun Mine and Mill Site, Leadpoint, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

...-Calhoun Mine and Mill Site, Leadpoint, WA AGENCY: Environmental Protection Agency (EPA). ACTION: Notice...-Calhoun Mine and Mill Site in Leadpoint, Washington, with settling party Blue Tee Corporation. The... Anderson-Calhoun Mine and Mill Site in Leadpoint, Washington, EPA Docket No. CERCLA-10-2010-0105 and should...

IN-SITU DUOX™ CHEMICAL OXIDATION TECHNOLOGY TO TREAT CHLORINATED ORGANICS AT THE ROOSEVELT MILLS SITE, VERNON, CT: SITE CHARACTERIZATION AND TREATABILITY STUDY

EPA Science Inventory

A study was performed investigating the feasibility of applying the DUOX™ chemical oxidation technology to chlorinated solvent contaminated media at the Roosevelt Mills site in Vernon, Connecticut. The Roosevelt Mills site is a former woolen mill that included dry cleaning operat...

77 FR 4559 - Ecusta Mill Site, Pisgah Forest, Transylvania County, NC; Notice of Amended Settlement

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-30

... ENVIRONMENTAL PROTECTION AGENCY [EPA-R4-SFUND 2012-; FRL-9624-1] Ecusta Mill Site, Pisgah Forest... settlement for resolution of past response and future costs concerning the Ecusta Mill Superfund Site located... settlement are available from Ms. Paula V. Painter. Submit your comments by Site name Ecusta Mill Superfund...

General View of Kinckley Knitting Mill site, east end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General View of Kinckley Knitting Mill site, east end of site along Wister Street, looking north, showing ruin of stone mill building and smoke stack of the Germantown Dyeworks in background - Hinckley Knitting Mills, 21-35 East Wister Street, Philadelphia, Philadelphia County, PA

76 FR 2145 - International Paper Company, Franklin Pulp & Paper Mill, Including On-Site Leased Workers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-12

... Company, Franklin Pulp & Paper Mill, Including On-Site Leased Workers From Railserve, Franklin, VA..., applicable to workers and former workers of International Paper Company, Franklin Pulp & Paper Mill, Franklin... follows: All workers International Paper Company, Franklin Pulp & Paper Mill, including on-site leased...

Baseline risk assessment of ground water contamination at the uranium mill tailings site near Durango, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1995-02-01

This risk assessment evaluates the possibility of health and environmental risks from contaminated ground water at the uranium mill tailings site near Durango, Colorado. The former uranium processing site`s contaminated soil and material were removed and placed at a disposal site located in Body Canyon, Colorado, during 1986--1991 by the US Departments of Energy`s Uranium Mill Tailings Remedial Action (UMTRA) Project. Currently, the UMTRA Project is evaluating the nature and extent of ground water contamination at the site. This risk assessment follows an approach similar to that used by the US Environmental Protection Agency. The first step is to determinemore » what site-related contaminants are found in ground water samples. The next step in the risk assessment is to determine how much of these contaminants people might ingest if they got their drinking water from a well on the site. In accordance with standard practice for this type of risk assessment, the highest contaminant concentrations from the most contaminated wells are used. The risk assessment then explains the possible health problems that could result from this amount of contamination.« less

Analysis and pollution sources speculations of toxic gases in a secondary fiber paper mill.

PubMed

Tong, Xin; Liu, Zhang; Chen, Xiao Q; Shen, Wen H

2016-11-09

This paper quantitatively investigates the compositions of the gaseous pollutants in the ambient air of a secondary fiber paper mill. Total volatile organic compounds (TVOC), formaldehyde (HCHO), sulfur compounds (H2S), and hydrocarbon compounds (CxHy) were analyzed on six sampling sites with photo-ionisation detector, acetylacetone spectrophotometric method, and gas detector. The results revealed that, the high levels of TVOC and CxHy were detected at the wet end of paper machine and the office area, respectively; all the H2S contents on the six sites exceeded the limit (0.06 mg m(-3)) seriously; the HCHO concentrations at other five sites were out of the limit (0.10 mg m(-3)) except for the wastewater treatment plant. Furthermore, the necessary discussions about the possible pollution sources were considered on the process flow, the chemical agents used, and the ambient conditions in the paper mill. For the sake of air pollution control in paper mills, these remarkable results and analysis lay some technical basis in the following researches that should attract more attentions.

Geochemistry of Mine Waste and Mill Tailings, Meadow Deposits, Streambed Sediment, and General Hydrology and Water Quality for the Frohner Meadows Area, Upper Lump Gulch, Jefferson County, Montana

USGS Publications Warehouse

Klein, Terry L.; Cannon, Michael R.; Fey, David L.

2004-01-01

Frohner Meadows, an area of low-topographic gradient subalpine ponds and wetlands in glaciated terrane near the headwaters of Lump Gulch (a tributary of Prickly Pear Creek), is located about 15 miles west of the town of Clancy, Montana, in the Helena National Forest. Mining and ore treatment of lead-zinc-silver veins in granitic rocks of the Boulder batholith over the last 120 years from two sites (Frohner mine and the Nellie Grant mine) has resulted in accumulations of mine waste and mill tailings that have been distributed downslope and downstream by anthropogenic and natural processes. This report presents the results of an investigation of the geochemistry of the wetlands, streams, and unconsolidated-sediment deposits and the hydrology, hydrogeology, and water quality of the area affected by these sources of ore-related metals. Ground water sampled from most shallow wells in the meadow system contained high concentrations of arsenic, exceeding the Montana numeric water-quality standard for human health. Transport of cadmium and zinc in ground water is indicated at one site near Nellie Grant Creek based on water-quality data from one well near the creek. Mill tailings deposited in upper Frohner Meadow contribute large arsenic loads to Frohner Meadows Creek; Nellie Grant Creek contributes large arsenic, cadmium, and zinc loads to upper Frohner Meadows. Concentrations of total-recoverable cadmium, copper, lead, and zinc in most surface-water sites downstream from the Nellie Grant mine area exceeded Montana aquatic-life standards. Nearly all samples of surface water and ground water had neutral to slightly alkaline pH values. Concentrations of arsenic, cadmium, lead, and zinc in streambed sediment in the entire meadow below the mine waste and mill tailings accumulations are highly enriched relative to regional watershed-background concentrations and exceed consensus-based, probable-effects concentrations for streambed sediment at most sites. Cadmium, copper, and zinc typically are adsorbed to the surface coatings of streambed-sediment grains. Mine waste and mill tailings contain high concentrations of arsenic, cadmium, copper, lead, and zinc in a quartz-rich matrix. Most of the waste sites that were sampled had low acid-generating capacity, although one site (fine-grained mill tailings from the Nellie Grant mine deposited in the upper part of lower Frohner Meadows) had extremely high acid-generating potential because of abundant fine-grained pyrite. Two distinct sites were identified as metal sources based on streambed-sediment samples, cores in the meadow substrate, and mine and mill-tailings samples. The Frohner mine and mill site contribute material rich in arsenic and lead; similar material from the Nellie Grant mine and mill site is rich in cadmium and zinc.

The source of groundwater and solutes to Many Devils Wash at a former uranium mill site in Shiprock, New Mexico

USGS Publications Warehouse

Robertson, Andrew J.; Ranalli, Anthony J.; Austin, Stephen A.; Lawlis, Bryan R.

2016-04-21

The Shiprock Disposal Site is the location of the former Navajo Mill (Mill), a uranium ore-processing facility, located on a terrace overlooking the San Juan River in the town of Shiprock, New Mexico. Following the closure of the Mill, all tailings and associated materials were encapsulated in a disposal cell built on top of the former Mill and tailings piles. The milling operations, conducted at the site from 1954 to 1968, created radioactive tailings and process-related wastes that are now found in the groundwater. Elevated concentrations of constituents of concern—ammonium, manganese, nitrate, selenium, strontium, sulfate, and uranium—have also been measured in groundwater seeps in the nearby Many Devils Wash arroyo, leading to the inference that these constituents originated from the Mill. These constituents have also been reported in groundwater that is associated with Mancos Shale, the bedrock that underlies the site. The objective of this report is to increase understanding of the source of water and solutes to the groundwater beneath Many Devils Wash and to establish the background concentrations for groundwater that is in contact with the Mancos Shale at the site. This report presents evidence on three working hypotheses: (1) the water and solutes in Many Devils Wash originated from the operations at the former Mill, (2) groundwater in deep aquifers is upwelling under artesian pressure to recharge the shallow groundwater beneath Many Devils Wash, and (3) the groundwater beneath Many Devils Wash originates as precipitation that infiltrates into the shallow aquifer system and discharges to Many Devils Wash in a series of springs on the east side of the wash. The solute concentrations in the shallow groundwater of Many Devils Wash would result from the interaction of the water and the Mancos Shale if the source of water was upwelling from deep aquifers or precipitation.In order to compare the groundwater from various wells to groundwater that has been affected by Mill activities, a classification system was developed to determine which wells were most likely to have been affected. Affects to groundwater by the Mill were determined by using the reported uranium alpha activity ratios measured in groundwater samples, along with the concentration of the uranium and the location of the wells relative to the Mill. Activity ratios of 1.2 or less were determined to be the most reliable indicator of Mill-affected groundwater. Wells with samples that had a reported activity ratio of 1.2 or less were classified as Mill affected. To compare groundwater with background water-quality, data from groundwater seeps and springs in the Upper Eagle Nest Arroyo and Salt Creek Wash, located north of the San Juan River, are also presented and analyzed.Based on groundwater elevations and tritium concentrations measured in wells located between the disposal cell and Many Devils Wash, Mill water is not likely to reach Many Devils Wash. The tritium concentrations also indicate that groundwater from the Mill has not substantially affected Many Devils Wash in the past. Upwelling from deep aquifers was also determined to be an unlikely source, primarily by comparing the composition of the stable isotopes of water in the shallow groundwater with those reported in groundwater samples from the deeper aquifers. The stable-isotope compositions of the shallow groundwater around the site are enriched relative to the San Juan River and local meteoric lines, which suggests that most of the shallow groundwater has been influenced by evaporation and therefore was recharged at the surface. Several observations indicate that focused recharge is the likely source of groundwater in the area of Many Devils Wash. The visible erosional features in Many Devils Wash provide evidence of piping and groundwater sapping, and the distribution and type of vegetation in Many Devils Wash suggest that the focused recharge of precipitation is occurring. The estimated recharge from precipitation was calculated to be 0.0008 inches per year (in/yr) by using the mass-balance approach from reported seep discharge and 0.0011 in/yr using the chloride mass-balance approach.A conceptual model of groundwater quality beneath Many Devils Wash is presented to explain the source of solutes in the groundwater beneath Many Devils Wash. The major-ion concentrations and geochemical evolution in the groundwater beneath Many Devils Wash and across the study area support the conceptual model that the underlying Mancos Shale is the source of solutes. Differences in the major-ion composition between groundwater samples collected around the site, result from the degree of weathering to the Mancos Shale. The cation distribution appears to be an indicator of effects from the Mill, with samples from the Mill-affected wells largely having a calcium/magnesium-sulfate composition that resembles the reported compositions of more weathered shale; however, that composition could change if the Mill-processed water flowed into areas where the Mancos Shale was less weathered. On the basis of the widespread presence of uranium in the Mancos Shale and the distribution of aqueous uranium in the analog sites and other sites in the region, it appears likely that uranium in the groundwater of Many Devils Wash is naturally sourced from the Mancos Shale.

Accumulation of environmental contaminants in wood duck (Aix sponsa) eggs, with emphasis on polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans

USGS Publications Warehouse

Augspurger, T.P.; Echols, K.R.; Peterman, P.H.; May, T.W.; Orazio, C.E.; Tillitt, D.E.; Di Giulio, R.T.

2008-01-01

We measured polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs), organochlorine pesticides, and mercury in wood duck (Aix sponsa) eggs collected near a North Carolina (USA) bleached kraft paper mill. Samples were taken a decade after the mill stopped using molecular chlorine. Using avian toxic equivalency factors, 2,3,7,8-tetrachlorodibenzo-p-dioxin toxicity equivalent (TEQ) concentrations were 1-30 pg/g fresh wet weight in eggs (n = 48) collected near the mill in 2002-2005 and were significantly higher than those from a reference site (<1 pg/g) 25 km away. Geometric mean wood duck egg TEQs (6 pg/g) were one-fifth those measured at this site prior to the cessation of molecular chlorine bleaching. Concentrations of mercury in wood duck eggs from nests of the Roanoke River sites ranged from 0.01 to 0.14 ??g/g (geometric mean, 0.04 ??g/g) and were significantly higher than those from the reference site, where concentrations did not exceed 0.04 ??g/g (geometric mean, 0.02 ??g/g). All concentrations were lower than those associated with adverse effects in birds. The congener profiles, lack of contamination in reference site eggs, and decline in contaminant concentrations after process changes at the mill provide strong evidence that mill discharges influenced contamination of local wood duck eggs. Collectively, the results indicate that the wood duck is an effective sentinel of the spatial and temporal extent of PCDD, PCDF, and mercury contamination. ?? 2008 US Government.

TECHNICAL APPROACHES TO CHARACTERIZING AND CLEANING UP IRON AND STEEL MILL SITES UNDER THE BROWNFIELDS INITIATIVE

EPA Science Inventory

This document provides brownfields planners with an overview of the technical methods that can be used to achieve successful site assessment and cleanup which are two key components of the brownfields redevelopment process. No two brownfields sites are identical and planners will...

78 FR 46948 - Proposed Agreement Regarding Site Costs and Covenants Not To Sue for American Lead and Zinc Mill...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-02

... Not To Sue for American Lead and Zinc Mill Site, Ouray County, Colorado AGENCY: Environmental... provides for Settling Party's payment of certain response costs incurred at the American Lead and Zinc Mill... reference the American Lead and Zinc Mill Site, the EPA Docket No. CERCLA-08-2013- 0004. The Agency's...

Pillsbury Mills LLC Removal Site

EPA Pesticide Factsheets

The Pillsbury Mills LLC removal site is located at 1525 E. Phillips St., Springfield, IL. Residential properties are located immediately across the street on the north and east perimeters. The site is a former Pillsbury grain mill on about 18 acres.

Superfund Record of Decision (EPA Region 8): Anaconda Smelter site, (Operable Unit 11 - Flue Dust), Deer Lodge County, Anaconda, MT. (Second remedial action), September 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-09-23

The 6,000-acre Anaconda Smelter site is a former copper and ore processing facility in Deer Lodge County, Montana. Land use in the area is predominantly residential. The site is bounded on the north and east, respectively, by the Warm Springs Creek and Mill Creek, both of which are potential sources of drinking water. From 1884 until 1980 when activities ceased, the site was used for ore processing and smelting operations. In 1988, EPA conducted an investigation to determine the nature and extent of the flue dust contamination. A 1988 ROD addressed the Mill Creek Operable Unit (OU15) and documented themore » relocation of residents from the community surrounding the smelter site as the selected remedial action. The Record of Decision (ROD) addresses the Flue Dust Operable Unit (OU11). The primary contaminants of concern affecting this site from the flue dust materials are metals including arsenic, cadmium, and lead. The selected remedial action for the site is included.« less

75 FR 69471 - Smurfit-Stone Container Corporation, Containerboard Mill, Including On-Site Leased Workers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-12

... Corporation, Containerboard Mill, Including On-Site Leased Workers From KMW Enterprises, Ontonagon, MI... to workers of Smurfit-Stone Container Corporation, Containerboard Mill, Ontonagon, Michigan. The... Ontonagon, Michigan location of Smurfit-Stone Container Corporation, Containerboard Mill. The Department has...

77 FR 40637 - Smurfit-Stone Container Corporation, Containerboard Mill, Including On-Site Leased Workers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-10

... Corporation, Containerboard Mill, Including On-Site Leased Workers From KMW Enterprises and General Security... Assistance on May 6, 2010, applicable to workers of Smurfit-Stone Container Corporation, Containerboard Mill... Ontonagon, Michigan location of Smurfit-Stone Container Corporation, Containerboard Mill, Ontonagon...

40 CFR 192.03 - Monitoring.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.03 Monitoring. A...

40 CFR 192.03 - Monitoring.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.03 Monitoring. A...

40 CFR 192.03 - Monitoring.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.03 Monitoring. A...

40 CFR 192.03 - Monitoring.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AND ENVIRONMENTAL PROTECTION STANDARDS FOR URANIUM AND THORIUM MILL TAILINGS Standards for the Control of Residual Radioactive Materials from Inactive Uranium Processing Sites § 192.03 Monitoring. A...

Buffer zone monitoring plan for the Dos Rios subdivision, Gunnison, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-02-01

This report presents a plan for water quality monitoring at the Dos Rios subdivision (Units 2, 3, and the Island Unit) that is intended to satisfy the informational needs of residents who live southwest (downgradient) of the former Gunnison processing site. Water quality monitoring activities described in this report are designed to protect the public from residual contamination that entered the ground water as a result of previous uranium milling operations. Requirements presented in this monitoring plan are also included in the water sampling and analysis plan (WSAP) for the Gunnison Uranium Mill Tailings Remedial Action (UMTRA) Project site. Themore » Gunnison WSAP is a site-specific document prepared by the U.S. Department of Energy (DOE) that provides background, guidance, and justification for future ground water sampling and analysis activities for the UMTRA Project Gunnison processing and disposal sites. The WSAP will be updated annually, as additional water quality data are collected and interpreted, to provide ongoing protection for public health and the environment.« less

Occurrence of selected pharmaceutical and non-pharmaceutical compounds, and stable hydrogen and oxygen isotope ratios, in a riverbank filtration study, Platte River, Nebraska, 2001 to 2003, Volume 1

USGS Publications Warehouse

Vogel, J.R.; Verstraeten, Ingrid M.; Coplen, T.B.; Furlong, E.T.; Meyer, M.T.; Barber, L.B.

2005-01-01

Although studied extensively in recent years in Europe, the occurrence of endocrine disrupters and other organic wastewater compounds in the environment in the United States is not well documented. To better understand the efficiency of riverbank filtration with respect to endocrine disrupting compounds and to evaluate the use of riverbank filtration as an effective means of drinking-water treatment, a study was conducted during 2001-2003 by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency and the City of Lincoln, at an established riverbank-filtration well field with horizontal collector wells and vertical wells. This study provides information that will be useful for (1) increased understanding of the processes and factors important in controlling the transport of endocrine disrupters, such as pesticides and pharmaceuticals during riverbank filtration, (2) better understanding of the physical and chemical processes that affect riverbank-filtration efficiency, and (3) managing the water resources of the eastern Platte River Basin. This report presents analytical methods and data collected during the study. Data are presented as generalized statistics and in figures showing temporal variations. Sites from which water-quality samples were collected for this study included wastewater sites (a cattle feedlot lagoon, a hog confinement lagoon, and wastewater-treatment plant effluent), surface-water sites (Platte River, Salt Creek, and Loup Power Canal), ground-water sites (one collector well and three vertical wells), and drinking-water sites (raw and finished). Field water-quality properties were measured in samples from these sites. Pharmaceutical compounds were detected often in the wastewater-treatment plant effluent. Surface and ground water showed low-level concentrations of pharmaceuticals. Finished drinking-water samples did not contain detectable concentrations of pharmaceuticals except for low levels of cotinine and caffeine. Antibiotics were found in some of the wastewater samples and twice in Salt Creek. Antibiotics were not detected in any samples from the Platte River or the well field. Surface-water samples were analyzed for total organic carbon and ground-water samples were analyzed for dissolved organic carbon. Samples from all sites were analyzed for major ions. Herbicides commonly detected in surface, ground, and drinking water included acetachlor, alachlor, atrazine, and metolachlor as well as degradates of these compounds. Most of the samples from wastewater sites were found to contain predominantly acetamide degradates. High concentrations of several organic wastewater indicator compounds were detected at the wastewater sites and in Salt Creek. Several organic wastewater indicator compounds were detected multiple times in samples from the Platte River. Bromoform, a by-product of disinfection in the treatment plant, was found in samples from the finished drinking water. Stable hydrogen isotope ratios show a range in seasonal variation of -73.6 per mill to -38.1 per mill relative to Vienna Standard Mean Ocean Water (VSMOW) reference water and -69.2 per mill to -46.5 per mill for surface water and ground water, respectively. Oxygen isotope ratios for surface-water samples varied between -9.86 per mill and -5.05 per mill. Stable oxygen isotope ratios of ground waters varied between -9.62 per mill and -5.81 per mill.

Superfund Record of Decision (EPA Region 6): Cimarron Mining Corporation site, Operable Unit 1, Lincoln County, Carrizozo, NM. (First remedial action), September 1990

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-09-21

The 10.6-acre Cimarron Mining site, Lincoln County, New Mexico, is an inactive milling facility used to recover iron from ores transported to the site. A shallow aquifer, which is not a potential drinking water source, and a deeper primary drinking water aquifer lie beneath the site. Cyanide was used until 1982 to recover precious metals. The operation of the mill resulted in the discharge of contaminated liquids onsite. The sources of environmental cyanide contamination at the site are the processed waste materials, including tailings piles and cinder block trench sediment piles, the cyanide solution and tailings spillage areas, and themore » cyanide solution recycling and disposal areas, including cinder block trenches and an unlined discharge pit. The major sources of ground water contamination by cyanide are the cinder block trenches and the discharge pit. These areas of prolonged contact between cyanide solution and underlying soil led to cyanide contamination in the shallow aquifer. The ROD addresses contaminated shallow ground water at the Cimarron Mining mill area as Operable Unit 1 (OU1). The primary contaminants of concern affecting the ground water are inorganics including cyanide.« less

75 FR 20386 - Auburn Hosiery Mills, Inc., Currently Known as Delta Galil, Including On-Site Leased Workers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-19

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-71,321] Auburn Hosiery Mills, Inc... Auburn Hosiery Mills, Inc., including on-site leased workers from Quality Personnel, Auburn, Kentucky... related to apparel. Information shows that Auburn Hosiery Mills was merged into its parent company, Delta...

75 FR 26794 - International Paper Company Franklin Pulp & Paper Mill Including On-Site Leased Workers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-12

... Company Franklin Pulp & Paper Mill Including On-Site Leased Workers From Railserve, Franklin, VA; Amended... workers of International Paper Company, Franklin Pulp & Paper Mill, Franklin, Virginia. The notice was... Pulp & Paper Mill. The Department has determined that these workers were sufficiently under the control...

40 CFR 61.151 - Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating...

Code of Federal Regulations, 2010 CFR

2010-07-01

... sites for asbestos mills and manufacturing and fabricating operations. 61.151 Section 61.151 Protection... STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos § 61.151 Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating operations. Each owner...

40 CFR 61.151 - Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating...

Code of Federal Regulations, 2013 CFR

2013-07-01

... sites for asbestos mills and manufacturing and fabricating operations. 61.151 Section 61.151 Protection... STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos § 61.151 Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating operations. Each owner...

40 CFR 61.151 - Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating...

Code of Federal Regulations, 2014 CFR

2014-07-01

... sites for asbestos mills and manufacturing and fabricating operations. 61.151 Section 61.151 Protection... STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos § 61.151 Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating operations. Each owner...

40 CFR 61.151 - Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating...

Code of Federal Regulations, 2011 CFR

2011-07-01

... sites for asbestos mills and manufacturing and fabricating operations. 61.151 Section 61.151 Protection... STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos § 61.151 Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating operations. Each owner...

40 CFR 61.151 - Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating...

Code of Federal Regulations, 2012 CFR

2012-07-01

... sites for asbestos mills and manufacturing and fabricating operations. 61.151 Section 61.151 Protection... STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos § 61.151 Standard for inactive waste disposal sites for asbestos mills and manufacturing and fabricating operations. Each owner...

Engineering assessment of inactive uranium mill tailings, Durango Site, Durango, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-06-01

Ford, Bacon and Davis Utah Inc. has reevaluated the Durango site in order to revise the November 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Durango, Colorado. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the nearly 1.6 million tons of tailings at the Durango sitemore » constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors. The four alternative actions presented in this engineering assessment range from millsite and off-site decontamination with the addition of 3 m of stabilization cover material (Option I), to removal of the tailings to remote disposal sites and decontamination of the tailings site (Options II through IV). Cost estimates for the seven options range from about $10,700,000 for stabilization in-place, to about $21,800,000 for disposal at a distance of about 10 mi. Three principal alternatives for the reprocessing of the Durango tailings were examined: (a) heap leaching; (b) treatment at an existing mill; and (c) reprocessing at a new conventional mill constructed for tailings reprocessing. The cost of the uranium recovered would be about $30/lb U/sub 3/O/sub 8/ by either heap leach or conventional plant processes.« less

Data Validation Package October 2015 Groundwater and Surface Water Sampling at the Monticello, Utah, Processing Site January 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Jason; Smith, Fred

Sampling Period: October 12–14, 2015. This semiannual event includes sampling groundwater and surface water at the Monticello Mill Tailings Site. Sampling and analyses were conducted as specified in the 2004 Monticello Mill Tailings Site Operable Unit III Post-Record of Decision Monitoring Plan, Draft Final and Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated). Samples were collected from 52 of 61 planned locations (15 of 17 former mill site wells, 17 of 18 downgradient wells, 9 of 9 downgradient permeable reactive barrier wells, 2 of 7 seeps and wetlands, and 9 ofmore » 10 surface water locations). Locations MW00-07, Seep 1, Seep 2, Seep 3, Seep 5, Seep 6, SW00-01, T01-13, and T01-19 were not sampled because of insufficient water availability. All samples were filtered as specified in the monitoring plan. Duplicate samples were collected from surface water location W3-04 and from monitoring wells 82-08, 92-09, and 92-10. Water levels were measured at all but one sampled well and an additional set of wells. The contaminants of concern (COCs) for the Monticello Mill Tailings Site are arsenic, manganese, molybdenum, nitrate + nitrite as nitrogen (nitrate + nitrite as N), selenium, uranium, and vanadium. Time-concentration graphs of the COCs for all groundwater and surface water locations are included in this report. Locations with COCs that exceeded remediation goals are listed.« less

Monticello Mill Tailings Site Operable Unit III Annual Groundwater Report May 2014 Through April 2015, October 2015

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Jason; Smith, Fred

This report provides the annual analysis of water quality restoration progress, cumulative through April 2015, for Operable Unit (OU) III, surface water and groundwater, of the U.S. Department of Energy (DOE) Office of Legacy Management Monticello Mill Tailings Site (MMTS). The MMTS is a Comprehensive Environmental Response, Compensation, and Liability Act National Priorities List site located in and near the city of Monticello, San Juan County, Utah. MMTS comprises the 110-acre site of a former uranium- and vanadium-ore-processing mill (mill site) and 1,700 acres of surrounding private and municipal property. Milling operations generated 2.5 million cubic yards of waste (tailings)more » from 1942 to 1960. The tailings were impounded at four locations on the mill site. Inorganic constituents in the tailings drained from the impoundments to contaminate local surface water (Montezuma Creek) and groundwater in the underlying alluvial aquifer. Mill tailings dispersed by wind and water also contaminated properties surrounding and downstream of the mill site. Remedial actions to remove and isolate radiologically contaminated soil, sediment, and debris from the former mill site (OU I) and surrounding properties (OU II) were completed in 1999 with the encapsulation of the wastes in an engineered repository located on DOE property 1 mile south of the former mill site. Contamination of groundwater and surface water remains within OU III at levels that exceed water quality protection standards. Uranium is the primary contaminant of concern. LM implemented monitored natural attenuation with institutional controls as the OU III remedy in 2004. Because groundwater restoration proceeded more slowly than expected and did not meet performance criteria established in the OU III Record of Decision (June 2004), LM implemented a contingency action in 2009 by an Explanation of Significant Difference to include a pump-and-treat system using a single extraction well and treatment by zero-valent iron (ex-situ treatment system). The contingency action was optimized in 2015 with the installation of 8 extraction wells and 16 monitoring wells in a focused area of the aquifer (area of attainment). Contaminated water is treated by solar evaporation at an existing onsite LM facility. Environmental monitoring at OU III consists of twice-yearly (April and October) collection and analysis of hydrologic and water-quality data from an established network of observation wells, seeps, and surface water locations. The scope of monitoring was expanded in 2009 for the ex situ treatment system and in 2015 for the remedy optimization system. Operation and monitoring of the ex situ treatment system was discontinued in 2014 with the start-up of the remedy optimization system. No data anomalies for OU III water quality trending or restoration progress are identified for the May 2014 through April 2015 reporting period. Although some regions of the aquifer demonstrate decreasing concentration trends, such trending is not evident for the bulk of the aquifer and a prolonged restoration period is indicated. The groundwater contingency remedy optimization system captures significant contaminant mass (primarily uranium) from the area of attainment; however, because that system only became operational in 2015, a long-term forecast of restoration progress is premature.« less

Geochemical investigation of UMTRAP designated site at Durango, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Markos, G.; Bush, K.J.

1983-09-01

This report is the result of a geochemical investigation of the former uranium mill and tailings site at Durango, Colorado. This is one in a series of site specific geochemical investigations performed on the inactive uranium mill tailings included in the UMTRA Project. The objectives of the investigation are to characterize the geochemistry, to determine the contaminant distribution resulting from the former milling activities and tailings, and to infer chemical pathways and transport mechanisms from the contaminant distribution. The results will be used to model contaminant migration and to develop criteria for long-term containment media such as a cover systemmore » which is impermeable to contaminant migration. This report assumes a familiarity with the hydrologic conditions of the site and the geochemical concepts underlying the investigation. The results reported are based on a one-time sampling of waters and solid material from the background, the area adjacent to the site, and the site. The solid samples are water extracted remove easily soluble salts and acids extracted to remove cabonates and hydroxides. The water extracts and solid samples were analyzed for the major and trace elements. A limited number of samples were analyzed for radiological components. The report includes the methods of sampling, sample processing, analysis, and data interpretation. Three major conclusions are: (1) carbonate salts and low TDS characterize the tailings; (2) the adjacent area and raffinate ponds contain contaminants deposited by a single event of fluid permeation of the soils; and (3) the Animas River adjacent to the site has elevated gross alpha activity attributed to /sup 226/Ra in the sediments derived from the tailings or milling activities.« less

25. View of Botany Mills Lanolin Retrieval plant site looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. View of Botany Mills Lanolin Retrieval plant site looking northwest from Andrew McLean Company Textile Mill; Botany Worsted Mills and Dundee Canal at left - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

1. VIEW OF THE WILBURWOMBLE MILL SITE, LOOKING NORTHEAST FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW OF THE WILBUR-WOMBLE MILL SITE, LOOKING NORTHEAST FROM LITTLE JOHNS CREEK. THE THREE CONCRETE MORTAR BLOCKS MARK THE LOCATION OF THE STAMP BATTERIES - Wilbur-Womble Mill, Southern Edge Of Salt Spring Valley, Copperopolis, Calaveras County, CA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kautsky, Mark; Ranalli, Tony; Dander, David

The objective of this investigation was to identify and differentiate potential non- mill-related water inputs to a shallow terrace groundwater system through the use of aqueous chemical and isotopic tracers at a former uranium- and vanadium-ore processing facility. Terrace groundwater in the vicinity of the Shiprock, New Mexico, site is hypothesized to be largely anthropogenic because natural rates of recharge in the terrace are likely insufficient to sustain a continuous water table in the terrace alluvial system, as observed in several analogue terrace locations east of the site and in response to post-mill dewatering efforts across the site. The terracemore » is composed of alluvial sand and gravel and weathered and unweathered Mancos Shale. Terrace groundwater exists and flows in the alluvium and to a much less extent in the Mancos Shale. Historical data established that in both the terrace and floodplain below the terrace, mill-derived uranium and sulfate is found primarily in the alluvium and the upper portion of the weathered Mancos Shale. Groundwater extraction is being conducted in the vicinity of former mill operations and in washes and seeps to dewater the formation and remove contamination, thus eliminating these exposure pathways and minimizing movement to the floodplain. However, past and present contribution of non-mill anthropogenic water sources may be hindering the dewatering effort, resulting in reduced remedy effectiveness. Groundwater source signatures can be determined based on chemical and isotopic ratios and are used to help identify and delineate both mill and non-mill water contributions. Aqueous chemical and isotopic tracers, such as 234U/238U activity ratios and uranium concentrations, δ34S sulfate and sulfate concentrations, tritium concentrations, and δ2Hwater and δ18O water are being used in this Phase I study. The aqueous chemical and isotopic analysis has identified areas on the terrace where groundwater is derived from mill-related activities and areas where the groundwater is associated with non-mill activities. A separate field effort of Phase II work will follow, including investigating additional locations for these isotopes and examination of δ18Osulfate , δ34Ssulfate , and chlorofluorocarbon signatures.« less

Uranium and radium concentrations in plants growing on uranium mill tailings in South Dakota

Treesearch

Mark A. Rumble; Ardell J. Bjugstad

1986-01-01

Vegetation and soil samples were collected from a uranium mill tailings site and control sites in South Dakota. Uranium concentrations in soils from the mill tailings averaged 13.3 [micro]g g-1 compared to 5.1 [micro]g g-1 in soils from control sites. 226Ra concentrations in soils averaged 111.0 pCi g...

24. View of Botany Mills Lanolin Retrieval plant site looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. View of Botany Mills Lanolin Retrieval plant site looking north from Andrew McLean Company Textile Mill; Botany Worsted Mills and Dundee Canal at left, Passaic River at right - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kautsky, Mark; Miller, David

This annual report evaluates the performance of the groundwater remediation system at the Shiprock, New Mexico, Disposal Site (Shiprock site) for the period April 2015 through March 2016. The Shiprock site, a former uranium-ore processing facility remediated under the Uranium Mill Tailings Radiation Control Act, is managed by the U.S. Department of Energy (DOE) Office of Legacy Management. This annual report is based on an analysis of groundwater quality and groundwater level data obtained from site monitoring wells and the groundwater flow rates associated with the extraction wells, drains, and seeps. Background The Shiprock mill operated from 1954 to 1968more » on property leased from the Navajo Nation. Remediation of surface contamination, including stabilization of mill tailings in an engineered disposal cell, was completed in 1986. During mill operation, nitrate, sulfate, uranium, and other milling-related constituents leached into underlying sediments and contaminated groundwater in the area of the mill site. In March 2003, DOE initiated active remediation of groundwater at the site using extraction wells and interceptor drains. At that time, DOE developed a baseline performance report that established specific performance standards for the Shiprock site groundwater remediation system. The Shiprock site is divided into two distinct areas: the floodplain and the terrace. The floodplain remediation system consists of two groundwater extraction wells, a seep collection drain, and two collection trenches (Trench 1 and Trench 2). The terrace remediation system consists of nine groundwater extraction wells, two collection drains (Bob Lee Wash and Many Devils Wash), and a terrace drainage channel diversion structure. All extracted groundwater is pumped into a lined evaporation pond on the terrace. Compliance Strategy and Remediation Goals As documented in the Groundwater Compliance Action Plan, the U.S. Nuclear Regulatory Commission–approved compliance strategy for the floodplain is natural flushing supplemented by active remediation. The contaminants of concern (COCs) at the site are ammonia (total as nitrogen), manganese, nitrate (nitrate + nitrite as nitrogen), selenium, strontium, sulfate, and uranium. The compliance standards for nitrate, selenium, and uranium are listed in Title 40 Code of Federal Regulations Part 192. Regulatory standards are not available for ammonia, manganese, and sulfate; remediation goals for these constituents are either risk-based alternate cleanup standards or background levels. These standards and background levels apply only to the compliance strategy for the floodplain. The compliance strategy for the terrace is to eliminate exposure pathways at the washes and seeps and to apply supplemental standards in the western section.« less

Remedial action plan and site design for stabilization of the inactive Uranium Mill Tailing site Maybell, Colorado. Attachment 3, ground water hydrology report, Attachment 4, water resources protection strategy. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-06-01

The U.S. Environmental Protection Agency (EPA) has established health and environmental regulations to correct and prevent ground water contamination resulting from former uranium processing activities at inactive uranium processing sites (40 CFR Part 192 (1993)) (52 FR 36000 (1978)). According to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 (42 USC {section} 7901 et seq.), the U.S. Department of Energy (DOE) is responsible for assessing the inactive uranium processing sites. The DOE has decided that each assessment will include information on hydrogeologic site characterization. The water resources protection strategy that describes the proposed action compliance with the EPAmore » ground water protection standards is presented in Attachment 4, Water Resources Protection Strategy. Site characterization activities discussed in this section include the following: (1) Definition of the hydrogeologic characteristics of the environment, including hydrostratigraphy, aquifer parameters, areas of aquifer recharge and discharge, potentiometric surfaces, and ground water velocities. (2) Definition of background ground water quality and comparison with proposed EPA ground water protection standards. (3) Evaluation of the physical and chemical characteristics of the contaminant source and/or residual radioactive materials. (4) Definition of existing ground water contamination by comparison with the EPA ground water protection standards. (5) Description of the geochemical processes that affect the migration of the source contaminants at the processing site. (6) Description of water resource use, including availability, current and future use and value, and alternate water supplies.« less

Remedial action plan and site design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-02-01

This appendix assesses the present conditions and data gathered about the two inactive uranium mill tailings sites near Rifle, Colorado, and the designated disposal site six miles north of Rifle in the area of Estes Gulch. It consolidates available engineering, radiological, geotechnical, hydrological, meteorological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill, tailings, and disposal site so that the Remedial Action Contractor (RAC) may complete final designs for the remedial actions.

Revitalizing America's Mills: A Report on Brownfields Mill Projects

EPA Pesticide Factsheets

This report focuses on mills -- former textile, wood, paper, iron, and steel mills. The report describes the challenges and opportunities of mill sites with case studies highlighting some of the most creative solutions from across the country.

Thatcher Bay, Washington, Nearshore Restoration Assessment

USGS Publications Warehouse

Breems, Joel; Wyllie-Echeverria, Sandy; Grossman, Eric E.; Elliott, Joel

2009-01-01

The San Juan Archipelago, located at the confluence of the Puget Sound, the Straits of Juan de Fuca in Washington State, and the Straits of Georgia, British Columbia, Canada, provides essential nearshore habitat for diverse salmonid, forage fish, and bird populations. With 408 miles of coastline, the San Juan Islands provide a significant portion of the available nearshore habitat for the greater Puget Sound and are an essential part of the regional efforts to restore Puget Sound (Puget Sound Shared Strategy 2005). The nearshore areas of the San Juan Islands provide a critical link between the terrestrial and marine environments. For this reason the focus on restoration and conservation of nearshore habitat in the San Juan Islands is of paramount importance. Wood-waste was a common by-product of historical lumber-milling operations. To date, relatively little attention has been given to the impact of historical lumber-milling operations in the San Juan Archipelago. Thatcher Bay, on Blakely Island, located near the east edge of the archipelago, is presented here as a case study on the restoration potential for a wood-waste contaminated nearshore area. Case study components include (1) a brief discussion of the history of milling operations. (2) an estimate of the location and amount of the current distribution of wood-waste at the site, (3) a preliminary examination of the impacts of wood-waste on benthic flora and fauna at the site, and (4) the presentation of several restoration alternatives for the site. The history of milling activity in Thatcher Bay began in 1879 with the construction of a mill in the southeastern part of the bay. Milling activity continued for more than 60 years, until the mill closed in 1942. Currently, the primary evidence of the historical milling operations is the presence of approximately 5,000 yd3 of wood-waste contaminated sediments. The distribution and thickness of residual wood-waste at the site was determined by using sediment coring and GIS-based interpolation techniques. Additionally, pilot studies were conducted to characterize in place sediment redox, organic composition, and sulfide impacts to nearshore flora and fauna. We found that the presence of wood-waste in Thatcher Bay may alter the quality of the benthic habitat by contributing to elevated levels of total organic composition (TOC) of the sediment. Increased TOC favors anaerobic respiration in marine sediments, and sulfide, a toxic by-product of this process, was found at levels as high as 17.5 mg L-1 in Thatcher Bay. The Thatcher Bay sulfide levels are several orders of magnitude higher than those known to impact benthic invertebrates. Eelgrass, Zostera marina, located on the western margin of Thatcher Bay, was surveyed by using underwater video surveys. This baseline distribution will in part be used to measure the impact of any future remediation efforts. Additionally, the distribution and survey data can provide an estimate of propagule source for future colonization of restored sediment. Three restoration alternatives were considered, and a ranking matrix was developed to score each alternative against site-specific and regional criteria. The process identified the removal of wood-waste from a water-based platform as the preferred alternative. Our multidisciplinary investigation identified the location, thickness, and potential impacts of wood-waste that has persisted in the nearshore environment of Thatcher Bay since at least 1942. We also provide a process to efficiently evaluate alternatives to remediate the impact of this historical disturbance and to potentially contribute to an increase of nearshore diversity and productivity at this site. Elements of this approach could inform restoration planning at similarly impacted sites throughout the region.

Assessment and evaluation of engineering options at a low-level radioactive waste storage site

NASA Astrophysics Data System (ADS)

Kanehiro, B. Y.; Guvanasen, V.

1982-09-01

Solutions to hydrologic and geotechnical problems associated with existing disposal sites were sought and the efficiency of engineering options that were proposed to improve the integrity of such sites were evaluated. The Weldon Spring site is generally like other low-level nuclear waste sites, except that the wastes are primarily in the form of residues and contaminated rubble from the processing of uranium and thorium ores rather than industrial isotopes or mill tailings.

THE INTERPLAY BETWEEN GEOCHEMICAL REACTIONS AND ADVECTION-DISPERSION IN CONTAMINANT TRANSPORT AT A URANIUM MILL TAILINGS SITE

EPA Science Inventory

It is well known that the fate and transport of contaminants in the subsurface are controlled by complex processes including advection, dispersion-diffusion, and chemical reactions. However, the interplay between the physical transport processes and chemical reactions, and their...

75 FR 28295 - Cummins Filtration, Including On-Site Leased Workers From Manpower and Spherion Staffing...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-20

... Hagemeyer North America, Lake Mills, IA; Amended Certification Regarding Eligibility To Apply for Worker... from Manpower, Lake Mills, Iowa. The notice was published in the Federal Register on December 11, 2009... America were employed on-site at the Lake Mills, Iowa location of Cummins Filtration to provide...

Predicting site locations for biomass using facilities with Bayesian methods

Treesearch

Timothy M. Young; James H. Perdue; Xia Huang

2017-01-01

Logistic regression models combined with Bayesian inference were developed to predict locations and quantify factors that influence the siting of biomass-using facilities that use woody biomass in the Southeastern United States. Predictions were developed for two groups of mills, one representing larger capacity mills similar to pulp and paper mills (Group II...

26. View looking west; Botany Mills Lanolin Retrieval plant site ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. View looking west; Botany Mills Lanolin Retrieval plant site in foreground, Botany Worsted Mill in distance - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

Remedial action plan and site design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado. Volume 2, Appendices D and E: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-02-01

This appendix assesses the present conditions and data gathered about the two inactive uranium mill tailings sites near Rifle, Colorado, and the designated disposal site six miles north of Rifle in the area of Estes Gulch. It consolidates available engineering, radiological, geotechnical, hydrological, meteorological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill, tailings, and disposal site so that the Remedial Action Contractor (RAC) may complete final designs for the remedial actions.

Respirable Crystalline Silica Exposures During Asphalt Pavement Milling at Eleven Highway Construction Sites

PubMed Central

Hammond, Duane R.; Shulman, Stanley A.; Echt, Alan S.

2016-01-01

Asphalt pavement milling machines use a rotating cutter drum to remove the deteriorated road surface for recycling. The removal of the road surface has the potential to release respirable crystalline silica, to which workers can be exposed. This paper describes an evaluation of respirable crystalline silica exposures to the operator and ground worker from two different half-lane and larger asphalt pavement milling machines that had ventilation dust controls and water-sprays designed and installed by the manufacturers. Manufacturer A completed milling for eleven days at four highway construction sites in Wisconsin, while Manufacturer B completed milling for ten days at seven highway construction sites in Indiana. To evaluate the dust controls, full-shift personal breathing zone air samples were collected from an operator and ground worker during the course of normal employee work activities of asphalt pavement milling at eleven different sites. Forty-two personal breathing zone air samples were collected over 21 days (sampling on an operator and ground worker each day). All samples were below 50 µg/m3 for respirable crystalline silica, the National Institute for Occupational Safety and Health recommended exposure limit. The geometric mean personal breathing zone air sample was 6.2 µg/m3 for the operator and 6.1 µg/m3 for the ground worker for the Manufacturer A milling machine. The geometric mean personal breathing zone air sample was 4.2 µg/m3 for the operator and 9.0 µg/m3 for the ground worker for the Manufacturer B milling machine. In addition, upper 95% confidence limits for the mean exposure for each occupation were well below 50 µg/m3 for both studies. The silica content in the bulk asphalt material being milled ranged from 7% to 23% silica for roads milled by Manufacturer A and from 5% to 12% silica for roads milled by Manufacturer B. The results indicate that engineering controls consisting of ventilation controls in combination with water-sprays are capable of controlling occupational exposures to respirable crystalline silica generated by asphalt pavement milling machines on highway construction sites. PMID:26913983

Respirable crystalline silica exposures during asphalt pavement milling at eleven highway construction sites.

PubMed

Hammond, Duane R; Shulman, Stanley A; Echt, Alan S

2016-07-01

Asphalt pavement milling machines use a rotating cutter drum to remove the deteriorated road surface for recycling. The removal of the road surface has the potential to release respirable crystalline silica, to which workers can be exposed. This article describes an evaluation of respirable crystalline silica exposures to the operator and ground worker from two different half-lane and larger asphalt pavement milling machines that had ventilation dust controls and water-sprays designed and installed by the manufacturers. Manufacturer A completed milling for 11 days at 4 highway construction sites in Wisconsin, and Manufacturer B completed milling for 10 days at 7 highway construction sites in Indiana. To evaluate the dust controls, full-shift personal breathing zone air samples were collected from an operator and ground worker during the course of normal employee work activities of asphalt pavement milling at 11 different sites. Forty-two personal breathing zone air samples were collected over 21 days (sampling on an operator and ground worker each day). All samples were below 50 µg/m(3) for respirable crystalline silica, the National Institute for Occupational Safety and Health recommended exposure limit. The geometric mean personal breathing zone air sample was 6.2 µg/m(3) for the operator and 6.1 µg/m(3) for the ground worker for the Manufacturer A milling machine. The geometric mean personal breathing zone air sample was 4.2 µg/m(3) for the operator and 9.0 µg/m(3) for the ground worker for the Manufacturer B milling machine. In addition, upper 95% confidence limits for the mean exposure for each occupation were well below 50 µg/m(3) for both studies. The silica content in the bulk asphalt material being milled ranged from 7-23% silica for roads milled by Manufacturer A and from 5-12% silica for roads milled by Manufacturer B. The results indicate that engineering controls consisting of ventilation controls in combination with water-sprays are capable of controlling occupational exposures to respirable crystalline silica generated by asphalt pavement milling machines on highway construction sites.

1. VIEW, LOOKING NORTHEAST, SHOWING THE SITE OF THE EMPIRE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW, LOOKING NORTHEAST, SHOWING THE SITE OF THE EMPIRE MILL. THE ADIT IS AT TOP, ABOVE THE TERRACES FOR THE CRUSHER AND 5-STAMP MILL. REMAINS OF THE BOILER HOUSING ARE ON THE LOWER TERRACE, AT RIGHT, WITH ENGINE MOUNT TO LEFT - Empire Mill, Southern Edge of Salt Spring Valley, Copperopolis, Calaveras County, CA

Superfund Record of Decision (EPA Region 8): Anaconda Smelter Site, Mill Creek, Montana (first remedial action), October 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-10-02

The 160-acre community of Mill Creek is located in Deerlodge County, Montana, immediately adjacent to the Anaconda Smelter NPL site. The community of Mill Creek has been contaminated for over 100 years with smelter emissions, fugitive emissions of flu dust at the smelter, and continued fugitive emissions emanating from adjacent highly contaminated soils. Settled flue emissions in the community of Mill Creek, from the now-defunct copper-smelting operation, contain arsenic, cadmium, and lead. Environmental siting of the community and biological testing of pre-school children, led EPA to conclude that contamination in the Mill Creek area poses an imminent and substantial endangermentmore » to the health of individuals residing there. The primary contaminant of concern at this site is arsenic. Cadmium and lead are secondary contaminants of concern. The selected remedial action for the site includes: permanent relocation of all residents (8 homes) with temporary erosional stabilization of disturbed areas by establishing and maintaining a vegetative cover; demolition, consolidation, and storage.« less

Final programmatic environmental impact statement for the uranium mill tailings remedial action ground water project. Volume I

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1996-10-01

This programmatic environmental impact statement (PElS) was prepared for the Uranium Mill Tailings Remedial Action (UMTRA) Ground Water Project to comply with the National Environmental Policy Act (NEPA). This PElS provides an analysis of the potential impacts of the alternatives and ground water compliance strategies as well as potential cumulative impacts. On November 8, 1978, Congress enacted the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law, codified at 42 USC §7901 et seq. Congress found that uranium mill tailings " ... may pose a potential and significant radiation health hazard to the public, and that every reasonablemore » effort should be made to provide for stabilization, disposal, and control in a safe, and environmentally sound manner of such tailings in order to prevent or minimize other environmental hazards from such tailings." Congress authorized the Secretary of Energy to designate inactive uranium processing sites for remedial action by the U.S. Department of Energy (DOE). Congress also directed the U.S. Environmental Protection Agency (EPA) to set the standards to be followed by the DOE for this process of stabilization, disposal, and control. On January 5, 1983, EPA published standards (40 CFR Part 192) for the disposal and cleanup of residual radioactive materials. On September 3, 1985, the U.S. Court of Appeals for the Tenth Circuit set aside and remanded to EPA the ground water provisions of the standards. The EPA proposed new standards to replace remanded sections and changed other sections of 40 CFR Part 192. These proposed standards were published in the Federal Register on September 24, 1987 (52 FR 36000). Section 108 of the UMTRCA requires that DOE comply with EPA's proposed standards in the absence of final standards. The Ground Water Project was planned under the proposed standards. On January 11, 1995, EPA published the final rule, with which the DOE must now comply. The PElS and the Ground Water Project are in accordance with the final standards. The EPA reserves the right to modify the ground water standards, if necessary, based on changes in EPA drinking water standards. Appendix A contains a copy of the 1983 EPA ground water compliance standards, the 1987 proposed changes to the standards, and the 1995 final rule. Under UMTRA, DOE is responsible for bringing the designated processing sites into compliance with the EPA ground water standards and complying with all other applicable standards and requirements. The U.S. Nuclear Regulatory Commission (NRC) must concur with DOE's actions. States are full participants in the process. The DOE also must consult with any affected Indian tribes and the Bureau of Indian Affairs. Uranium processing activities at most of the inactive mill sites resulted in the contamination of ground water beneath and, in some cases, downgradient of the sites. This contaminated ground water often has elevated levels of constituents such as but not limited to uranium and nitrates. The purpose of the UMTRA Ground Water Project is to eliminate or reduce to acceptable levels the potential health and environmental consequences of milling activities by meeting the EPA ground water standards.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamboj, Sunita; Durham, Lisa A.

A post-remediation radiological dose assessment was conducted for the Formerly Utilized Sites Remedial Action Program (FUSRAP) Linde Site by using the measured residual concentrations of the radionuclides of concern following the completion of the soils remedial action. The site’s FUSRAP-related contaminants of concern (COCs) are radionuclides associated with uranium processing activities conducted by the Manhattan Engineer District (MED) in support of the Nation’s early atomic energy and weapons program and include radium-226 (Ra-226), thorium-230 (Th-230), and total uranium (Utotal). Remedial actions to address Linde Site soils and structures were conducted in accordance with the Record of Decision for the Lindemore » Site, Tonawanda, New York (ROD) (USACE 2000a). In the ROD, the U.S. Army Corps of Engineers (USACE) determined that the cleanup standards found in Title 40, Part 192 of the Code of Federal Regulations (40 CFR Part 192), the standards for cleanup of uranium mill sites designated under the Uranium Mill Tailings Radiation Control Act (UMTRCA), and the Nuclear Regulatory Commission (NRC) standards for decommissioning of licensed uranium and thorium mills, found in 10 CFR Part 40, Appendix A, Criterion 6(6), are Applicable or Relevant and Appropriate Requirements (ARARs) for cleanup of MED-related contamination at the Linde Site. The major elements of this remedy will involve excavation of the soils with COCs above soil cleanup levels and placement of clean materials to meet the other criteria of 40 CFR Part 192.« less

Biogeochemical aspects of uranium mineralization, mining, milling, and remediation

USGS Publications Warehouse

Campbell, Kate M.; Gallegos, Tanya J.; Landa, Edward R.

2015-01-01

Natural uranium (U) occurs as a mixture of three radioactive isotopes: 238U, 235U, and 234U. Only 235U is fissionable and makes up about 0.7% of natural U, while 238U is overwhelmingly the most abundant at greater than 99% of the total mass of U. Prior to the 1940s, U was predominantly used as a coloring agent, and U-bearing ores were mined mainly for their radium (Ra) and/or vanadium (V) content; the bulk of the U was discarded with the tailings (Finch et al., 1972). Once nuclear fission was discovered, the economic importance of U increased greatly. The mining and milling of U-bearing ores is the first step in the nuclear fuel cycle, and the contact of residual waste with natural water is a potential source of contamination of U and associated elements to the environment. Uranium is mined by three basic methods: surface (open pit), underground, and solution mining (in situ leaching or in situ recovery), depending on the deposit grade, size, location, geology and economic considerations (Abdelouas, 2006). Solid wastes at U mill tailings (UMT) sites can include both standard tailings (i.e., leached ore rock residues) and solids generated on site by waste treatment processes. The latter can include sludge or “mud” from neutralization of acidic mine/mill effluents, containing Fe and a range of coprecipitated constituents, or barium sulfate precipitates that selectively remove Ra (e.g., Carvalho et al., 2007). In this chapter, we review the hydrometallurgical processes by which U is extracted from ore, the biogeochemical processes that can affect the fate and transport of U and associated elements in the environment, and possible remediation strategies for site closure and aquifer restoration.This paper represents the fourth in a series of review papers from the U.S. Geological Survey (USGS) on geochemical aspects of UMT management that span more than three decades. The first paper (Landa, 1980) in this series is a primer on the nature of tailings and radionuclide mobilization from them. The second paper (Landa, 1999) includes coverage of research carried out under the U.S. Department of Energy’s Uranium Mill Tailings Remedial Action Program (UMTRA). The third paper (Landa, 2004) reflects the increased focus of researchers on biotic effects in UMT environs. This paper expands the focus to U mining, milling, and remedial actions, and includes extensive coverage of the increasingly important alkaline in situ recovery and groundwater restoration.

Using existing growth models to predict RCW habitat development following site preparation: pitfalls of the process and potential growth response

Treesearch

Benjamin O. Knapp; Joan L. Walker

2013-01-01

Land managers throughout the Southeast are interested in restoring the longleaf pine (Pinus palustris Mill.) ecosystem, due in part to its value as habitat for the endangered red-cockaded woodpecker (Picoides borealis). In 2003, we established a study at Camp Lejeune, NC, to determine the effects of common site preparation...

41. View of Botany Worsted Mills looking southeast from site ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. View of Botany Worsted Mills looking southeast from site of former Forstmann and Huffman textile mill; water tank (No. 43A) at center, Dundee Canal to left - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muldoon, Joe; Yankovich, Tamara; Schramm, Laurier L.

The Gunnar Mine and mill site was the largest of some 38 now-abandoned uranium mines that were developed and operated in Northern Saskatchewan, Canada, during the Cold War years. During their operating lifetimes these mines produced large quantities of ore and tailings. The Gunnar mine (open pit and underground) produced over 5 million tonnes of uranium ore and nearly 4.4 million tonnes of mine tailings during its operations from 1955 through 1963. An estimated 2.2 to 2.7 million m{sup 3} of waste rock that was generated during the processing of the ore abuts the shores of Lake Athabasca, the 22.more » largest lake in the world. After closure in the 1960's, the Gunnar site was abandoned with little to no decommissioning being done. The Saskatchewan Research Council has been contracted to manage the clean-up of these abandoned northern uranium mine and mill sites. The Gunnar Mine, because of the magnitude of tailings and waste rock, is subject to an environmental site assessment process regulated by both provincial and federal governments. This process requires a detailed study of the environmental impacts that have resulted from the mining activities and an analysis of projected impacts from remediation efforts. The environmental assessment process, specific site studies, and public involvement initiatives are all now well underway. Due to the many uncertainties associated with an abandoned site, an adaptive remediation approach, utilizing a decision tree, presented within the environmental assessment documents will be used as part of the site regulatory licensing. A critical early task was dealing with major public safety hazards on the site. The site originally included many buildings that were remnants of a community of approximately 800 people who once occupied the site. These buildings, many of which contained high levels of asbestos, had to be appropriately abated and demolished. Similarly, the original mine head frame and mill site buildings, many of which still contained the original machinery and equipment, also had to be dismantled. Remediation options for the accumulated demolition debris have been assessed, as have remediation options for the waste rock and tailings, all of which form part of the environmental assessment. The regulatory requirements include the environmental assessment processes, a complex public involvement strategy, and licensing from the Canadian Nuclear Safety Commission (CNSC) with the long-term goal of releasing the property in a remediated and stable state to the Province of Saskatchewan. Prescribed environmental and land use endpoints will be determined based on the environmental assessment studies and remediation options analyzed and implemented. Ultimately, the site will be released into an institutional controls program that will allow long-term government management and monitoring. (authors)« less

TECHNICAL APPROACHES TO CHARACTERIZING AND CLEANING UP BROWNFIELDS SITES: PULP AND PAPER MILLS

EPA Science Inventory

This guidance document gives assistance to communities, decision-makers, states and municipalities, academia, and the private sector to address issues related to the redevelopment of Brownfields sites, specifically pulp and paper mills sites. The document helps users to understan...

10 CFR 40.2a - Coverage of inactive tailings sites.

Code of Federal Regulations, 2011 CFR

2011-01-01

... materials as defined in this part that are located at a site where milling operations are no longer active... defined in this part that is located at a site where milling operations are no longer active, if such site... 10 Energy 1 2011-01-01 2011-01-01 false Coverage of inactive tailings sites. 40.2a Section 40.2a...

10 CFR 40.2a - Coverage of inactive tailings sites.

Code of Federal Regulations, 2012 CFR

2012-01-01

... materials as defined in this part that are located at a site where milling operations are no longer active... defined in this part that is located at a site where milling operations are no longer active, if such site... 10 Energy 1 2012-01-01 2012-01-01 false Coverage of inactive tailings sites. 40.2a Section 40.2a...

10 CFR 40.2a - Coverage of inactive tailings sites.

Code of Federal Regulations, 2014 CFR

2014-01-01

... materials as defined in this part that are located at a site where milling operations are no longer active... defined in this part that is located at a site where milling operations are no longer active, if such site... 10 Energy 1 2014-01-01 2014-01-01 false Coverage of inactive tailings sites. 40.2a Section 40.2a...

10 CFR 40.2a - Coverage of inactive tailings sites.

Code of Federal Regulations, 2013 CFR

2013-01-01

... materials as defined in this part that are located at a site where milling operations are no longer active... defined in this part that is located at a site where milling operations are no longer active, if such site... 10 Energy 1 2013-01-01 2013-01-01 false Coverage of inactive tailings sites. 40.2a Section 40.2a...

Influence of Harvest Aid Herbicides on Seed Germination, Seedling Vigor and Milling Quality Traits of Red Lentil (Lens culinaris L.).

PubMed

Subedi, Maya; Willenborg, Christian J; Vandenberg, Albert

2017-01-01

Most red lentil produced worldwide is consumed in dehulled form, and post-harvest milling and splitting qualities are major concerns in the secondary processing industry. Lentil producers in northern temperate regions usually apply pre-harvest desiccants as harvest aids to accelerate the lentil crop drying process and facilitate harvesting operations. This paper reports on field studies conducted at Scott and Saskatoon, Saskatchewan, Canada in the 2012 and 2013 cropping seasons to evaluate whether herbicides applied as harvest aids alone or tank mixed with glyphosate affect seed germination, seedling vigor, milling, and splitting qualities. The site-year by desiccant treatment interaction for seed germination, vigor, and milling recovery yields was significant. Glyphosate applied alone or as tank mix with other herbicides (except diquat) reduced seed germination and seedling vigor at Saskatoon and Scott in 2012 only. Pyraflufen-ethyl (20 g ai ha -1 ) applied with glyphosate as well as saflufenacil (36 g ai ha -1 ) decreased dehulling efficiency, while saflufenacil and/or glufosinate with glyphosate reduced milling recovery and football recovery, although these effects were inconsistent. Application of diquat alone or in combination with glyphosate exhibited more consistent dehulling efficiency gains and increases in milling recovery yield. Significant but negative associations were observed between glyphosate residue in seeds and seed germination ( r = -0.84, p < 0.001), seed vigor ( r = -0.62, p < 0.001), dehulling efficiency ( r = -0.55, p < 0.001), and milling recovery ( r = -0.62, p < 0.001). These results indicate application of diquat alone or in combination with glyphosate may be a preferred option for lentil growers to improve milling recovery yield.

Influence of Harvest Aid Herbicides on Seed Germination, Seedling Vigor and Milling Quality Traits of Red Lentil (Lens culinaris L.)

PubMed Central

Subedi, Maya; Willenborg, Christian J.; Vandenberg, Albert

2017-01-01

Most red lentil produced worldwide is consumed in dehulled form, and post-harvest milling and splitting qualities are major concerns in the secondary processing industry. Lentil producers in northern temperate regions usually apply pre-harvest desiccants as harvest aids to accelerate the lentil crop drying process and facilitate harvesting operations. This paper reports on field studies conducted at Scott and Saskatoon, Saskatchewan, Canada in the 2012 and 2013 cropping seasons to evaluate whether herbicides applied as harvest aids alone or tank mixed with glyphosate affect seed germination, seedling vigor, milling, and splitting qualities. The site-year by desiccant treatment interaction for seed germination, vigor, and milling recovery yields was significant. Glyphosate applied alone or as tank mix with other herbicides (except diquat) reduced seed germination and seedling vigor at Saskatoon and Scott in 2012 only. Pyraflufen-ethyl (20 g ai ha−1) applied with glyphosate as well as saflufenacil (36 g ai ha−1) decreased dehulling efficiency, while saflufenacil and/or glufosinate with glyphosate reduced milling recovery and football recovery, although these effects were inconsistent. Application of diquat alone or in combination with glyphosate exhibited more consistent dehulling efficiency gains and increases in milling recovery yield. Significant but negative associations were observed between glyphosate residue in seeds and seed germination (r = −0.84, p < 0.001), seed vigor (r = −0.62, p < 0.001), dehulling efficiency (r = −0.55, p < 0.001), and milling recovery (r = −0.62, p < 0.001). These results indicate application of diquat alone or in combination with glyphosate may be a preferred option for lentil growers to improve milling recovery yield. PMID:28352275

1996 monitoring report for the Gunnison, Colorado, wetlands mitigation plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-01

The US Department of Energy (DOE) administers the Uranium Mill Tailings Remedial Action (UMTRA) Project to clean up uranium mill tailings and other surface contamination at 24 abandoned uranium mill sites in 10 states. One of these abandoned mill sites was near the town of Gunnison, Colorado. Surface remediation was completed at the Gunnison site in December 1995. Remedial action resulted in the elimination of 4.3 acres of wetlands and mitigation of this loss is through the enhancement of 17.8 acres of riparian plant communities in six spring-fed areas on US Bureau of Land Management mitigation sites. A five-year monitoringmore » program was then implemented to document the response of vegetation and wildlife to the exclusion of livestock. This report provides the results of the third year of the monitoring program.« less

Evaluation of impacts and mitigation assessments for the UMTRA Project: Gunnison and Durango pilot studies. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beranich, S.J.

1994-08-24

This report evaluates the impacts assessment and proposed mitigations provided in environmental documents concerning the US Department of Energy`s (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The projected impacts and proposed mitigations identified in UMTRA Project environmental documents were evaluated for two UMTRA Project sites. These sites are Gunnison and Durango, which are representative of currently active and inactive UMTRA Project sites, respectively. National Environmental Policy Act (NEPA) documentation was prepared for the remedial action at Durango and Gunnison as well as for the provision of an alternate water supply system at Gunnison. Additionally, environmental analysis was completed formore » mill site demolition Gunnison, and for a new road related to the Durango remedial action. The results in this report pertain only to the impact assessments prepared by the Regulatory Compliance staff as a part of the NEPA compliance requirements. Similarly, the mitigative measures documented are those that were identified during the NEPA process.« less

Regulatory Oversight of the Legacy Gunner Uranium Mine and Mill Site in Northern Saskatchewan, Canada - 13434

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stenson, Ron; Howard, Don

2013-07-01

As Canada's nuclear regulator, the Canadian Nuclear Safety Commission (CNSC) is responsible for licensing all aspects of uranium mining, including remediation activities at legacy sites. Since these sites already existed when the current legislation came into force in 2000, and the previous legislation did not apply, they present a special case. The Nuclear Safety and Control Act (NSCA), was written with cradle-to- grave oversight in mind. Applying the NSCA at the end of a 'facilities' life-cycle poses some challenges to both the regulator and the proponent. When the proponent is the public sector, even more challenges can present themselves. Althoughmore » the licensing process for legacy sites is no different than for any other CNSC license, assuring regulatory compliance can be more complicated. To demonstrate how the CNSC has approached the oversight of legacy sites the history of the Commission's involvement with the Gunnar uranium mine and mill site provides a good case study. The lessons learned from the CNSC's experience regulating the Gunnar site will benefit those in the future who will need to regulate legacy sites under existing or new legislation. (authors)« less

Engineering assessment of inactive uranium mill tailings: Maybell Site, Maybell, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1981-09-01

Ford, Bacon and Davis Utah Inc. has reevaluated the Maybell site in order to revise the October 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Maybell, Colorado. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 2.6 million dry tons of tailings at the Maybell sitemore » constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors. The two alternative actions presented in this engineering assessment range from millsite decontamination with the addition of 3 m of stabilization cover material (Option I), to disposal of the tailings in a nearby open pit mine and decontamination of the tailings site (Option II). Cost estimates for the two options are about $11,700,000 for stabilization in-place and about $22,700,000 for disposal within a distance of 2 mi. Three principal alternatives for the reprocessing of the Maybell tailings were examined: (a) heap leaching; (b) treatment at an existing mill; and (c) reprocessing at a new conventional mill constructed for tailings reprocessing. The cost of the uranium recovered would be about $125 and $165/lb of U/sub 3/O/sub 8/ by heap leach and conventional plant processes, respectively. The spot market price for uranium was $25/lb early in 1981. Therefore, reprocessing the tailings for uranium recovery is not economically attractive at present.« less

Engineering assessment of inactive uranium mill tailings: Maybell Site, Maybell, Colorado. Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1981-09-01

Ford, Bacon and Davis Utah Inc. has reevaluated the Maybell site in order to revise the October 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Maybell, Colorado. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 2.6 million dry tons of tailings at the Maybell sitemore » constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors. The two alternative actions presented in this engineering assessment range from millsite decontamination with the addition of 3 m of stabilization cover material (Option I), to disposal of the tailings in a nearby open pit mine and decontamination of the tailings site (Option II). Cost estimates for the two options are about $11,700,000 for stabilization in-place and about $22,700,000 for disposal within a distance of 2 mi. Three principal alternatives for the reprocessing of the Maybell tailings were examined: (a) heap leaching; (b) treatment at an existing mill; and (c) reprocessing at a new conventional mill constructed for tailings reprocessing. The cost of the uranium recovered would be about $125 and $165/lb of U/sub 3/O/sub 8/ by heap leach and conventional plant processes, respectively. The spot market price for uranium was $25/lb early in 1981. Therefore, reprocessing the tailings for uranium recovery is not economically attractive at present.« less

Changes of floodplain morphology by water mills: Legacy sediments stored behind mill dams as archive and source for pollution - Examples from the Wurm River, Lower Rhine Embayment, Germany

NASA Astrophysics Data System (ADS)

Buchty-Lemke, Michael; Frings, Roy; Hagemann, Lukas; Lehmkuhl, Frank; Maaß, Anna-Lisa; Schwarzbauer, Jan

2016-04-01

The Wurm River (Lower Rhine Embayment, Germany) is a small stream in a low mountain area near the Dutch-German border that has seen a lot of anthropogenic changes of its morphology since medieval times. Among other influencing factors, water mills, in particular, had an early impact on the sediment dynamics and created sediment traps. Several knickpoints in the long profile may represent the legacy of mill damming - or founded mill building at these spots. The knickpoints may also represent the aftermath of the colliery history. A study site in the upper reaches of the Wurm River features erosion terraces, incised following the demise of a mill dam in the early 20th century. The mill pond most likely collected sediment and additives e.g. used in agricultural and industrial processes. These legacy sediments from behind former mill dams provide information about anthropogenic pollution, particularly for the era of industrialization in the vicinity of the old industrial area of the city of Aachen. Along with the demise of the mill dam and the increased incision tendency, the sediments are also a secondary source for pollution in case of remobilization of contaminated sediments. Two major research questions are addressed. A) Which individual hydrological and geomorphological processes, both upstream and downstream, triggered the incision and the construction of the erosion terraces, which are preserved in the mill pond sediments? Is either the demised mill dam, or subsidence effects, or a combination of both the determining factor? B) Which contaminants are retained in the sediments? Is there a detectable point source for the pollutants or is it a mixture of diffuse anthropogenic (industry, agriculture, traffic, wastewater) and natural origin? To tackle these questions, sedimentological data are combined with geomorphological mapping and evaluation of historical data. A soil profile provides insight into the architecture of the floodplain, which is built of riverbed sediments overlain by stratified fine clastic and organic-rich material, representing the sediment being trapped when the mill dam existed. X-ray fluorescence and grain size analysis are used to determine the depositional process, provenance and chemostratigraphy. Knowledge about the distribution and fate of pollutants in sediments is valuable for river management purposes. Measures within the scope of the EU Water Framework Directive have been implemented at several breaches at the Wurm River, and further ones are planned. Potential risks due to remobilization of polluted alluvial sediments must thereby be taken into account. Furthermore, e.g. dismantling of transverse structures to improve passage for fish might trigger similar erosion processes and affects the sediment continuity.

Chalk Line Mill, Anniston, AL

EPA Pesticide Factsheets

The Chalk Line Mill property was the site of a textile mill which operated from 1887 until 1994. Demolition activities in 2004 removed most of the structures on-site, but also left large, unsightly piles of debris scattered across this 14-acre property. The City applied for and received a $200,000 Brownfields cleanup grant in 2007 to address contamination on the property and the Appalachian Regional Commission provided an additional $150,000 in funding.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The site observational work plan (SOWP) for the Riverton, Wyoming, Uranium Mill Tailings Remedial Action (UMTRA) Project Site is the first document for the UMTRA Ground Water Project to address site-specific activities to meet compliance with the U.S. Environmental Protection Agency (EPA) proposed ground water standards (52 FR 36000 (1987)). In support of the activities the regulatory framework and drivers are presented along with a discussion of the relationship of this SOWP to other UMTRA Ground Water Project programmatic documents. A combination of the two compliance strategies that will be recommended for this site are no remediation with the applicationmore » of alternate concentration levels (ACL) and natural flushing in conjunction with institutional controls. ACLs are to be applied to constituents that occur at concentrations above background levels but which are essential nutrients and occur within nutritional ranges and/or have very low toxicity and high dietary intake rates compared to the levels detected in the ground water. The essential premise of natural flushing is that ground water movement and natural attenuation processes will reduce the detected contamination to background levels within 1 00 years. These two recommended compliance strategies were evaluated by applying Riverton site-specific data to the compliance framework developed in the UMTRA Ground Water programmatic environmental impact statement. There are three aquifers beneath the site: a surficial unconfined aquifer, a middle semiconfined aquifer, and a deeper confined aquifer. The milling-related contamination at the site has affected both the surficial and semiconfined aquifers, although the leaky shale aquifers separating these units limits the downward migration of contamination into the semiconfined aquifer. A shale aquitard separates the semiconfined aquifer from the underlying confined aquifer which has not been contaminated by milling-related constituents.« less

Data Validation Package October 2016 Groundwater and Surface Water Sampling at the Monticello, Utah, Disposal and Processing Sites January 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Jason; Smith, Fred

Sampling Period: October 10–12, 2016. This semiannual event includes sampling groundwater and surface water at the Monticello Disposal and Processing Sites. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated) and Program Directive MNT-2016-01. Samples were collected from 54 of 64 planned locations (16 of 17 former mill site wells, 15 of 18 downgradient wells, 7 of 9 downgradient permeable reactive barrier wells, 3 of 3 bedrock wells, 4 of 7 seeps and wetlands, and 9 of 10 surface water locations).

Ecological, political and social challenges of prescribed fire restoration in east Texas pineywoods ecosystems: a case study

Treesearch

Sandra Rideout; Brian P. Oswald; Michael H. Legg

2003-01-01

The effectiveness of prescribed fire restoration of forested sites in three state parks in east Texas, USA was studied. Two sites consisted of mixed shortleaf (Pinus echinata Mill.) or loblolly pine (Pinus taeda L.) and broadleaf overstoreys. The third site was a longleaf pine (Pinus palustris Mill.)/little...

DEMONSTRATION BULLETIN: ADSORPTION-INTEGRATED-REACTION (AIR2000) PROCESS, KSE, INC.

EPA Science Inventory

This Bulletin is a brief description of the AIR2000 technology developed by KSE, Inc., of Amherst, MA. The AIR2000 unit treats air streams containing volatile organic compounds (VOCs). The demonstration occurred at the Stamina Mills superfund site in North Smithfield, RI from Aug...

US Department of Energy response to standards for remedial actions at inactive uranium processing sites: Proposed rule

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-01-29

The Title I groundwater standards for inactive uranium mill tailings sites, which were promulgated on January 5, 1983, by the US Environmental Protection Agency (EPA) for the Uranium Mill Tailings Remedial Action (UMTRA) Project, were remanded to the EPA on September 3, 1985, by the US Tenth Circuit Court of Appeals. The Court instructed the EPA to compile general groundwater standards for all Title I sites. On September 24, 1987, the EPA published proposed standards (52FR36000-36008) in response to the remand. This report includes an evaluation of the potential effects of the proposed EPA groundwater standards on the UMTRA Project,more » as well as a discussion of the DOE's position on the proposed standards. The report also contains and appendix which provides supporting information and cost analyses. In order to assess the impacts of the proposed EPA standards, this report summarizes the proposed EPA standards in Section 2.0. The next three sections assess the impacts of the three parts of the EPA standards: Subpart A considers disposal sites; Subpart B is concerned with restoration at processing sites; and Subpart C addresses supplemental standards. Section 6.0 integrates previous sections into a recommendations section. Section 7.0 contains the DOE response to questions posed by the EPA in the preamble to the proposed standards. 6 refs., 5 figs., 3 tabs.« less

78 FR 29155 - Notice of Filing of Plats of Survey; Montana

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-17

..., representing the dependent resurvey of M.S. No. 551, Strawberry Lode; M.S. No. 780, Strawberry Lode; M.S. No.781, Strawberry Extension Lode; M.S. No. 2599B, Clipper Mill Site; M.S. No. 2617B, Rustler Mill Site...

Enzymatic corn wet milling: engineering process and cost model

PubMed Central

Ramírez, Edna C; Johnston, David B; McAloon, Andrew J; Singh, Vijay

2009-01-01

Background Enzymatic corn wet milling (E-milling) is a process derived from conventional wet milling for the recovery and purification of starch and co-products using proteases to eliminate the need for sulfites and decrease the steeping time. In 2006, the total starch production in USA by conventional wet milling equaled 23 billion kilograms, including modified starches and starches used for sweeteners and ethanol production [1]. Process engineering and cost models for an E-milling process have been developed for a processing plant with a capacity of 2.54 million kg of corn per day (100,000 bu/day). These models are based on the previously published models for a traditional wet milling plant with the same capacity. The E-milling process includes grain cleaning, pretreatment, enzymatic treatment, germ separation and recovery, fiber separation and recovery, gluten separation and recovery and starch separation. Information for the development of the conventional models was obtained from a variety of technical sources including commercial wet milling companies, industry experts and equipment suppliers. Additional information for the present models was obtained from our own experience with the development of the E-milling process and trials in the laboratory and at the pilot plant scale. The models were developed using process and cost simulation software (SuperPro Designer®) and include processing information such as composition and flow rates of the various process streams, descriptions of the various unit operations and detailed breakdowns of the operating and capital cost of the facility. Results Based on the information from the model, we can estimate the cost of production per kilogram of starch using the input prices for corn, enzyme and other wet milling co-products. The work presented here describes the E-milling process and compares the process, the operation and costs with the conventional process. Conclusion The E-milling process was found to be cost competitive with the conventional process during periods of high corn feedstock costs since the enzymatic process enhances the yields of the products in a corn wet milling process. This model is available upon request from the authors for educational, research and non-commercial uses. PMID:19154623

Wastewater disposal to landfill-sites: a synergistic solution for centralized management of olive mill wastewater and enhanced production of landfill gas.

PubMed

Diamantis, Vasileios; Erguder, Tuba H; Aivasidis, Alexandros; Verstraete, Willy; Voudrias, Evangelos

2013-10-15

The present paper focuses on a largely unexplored field of landfill-site valorization in combination with the construction and operation of a centralized olive mill wastewater (OMW) treatment facility. The latter consists of a wastewater storage lagoon, a compact anaerobic digester operated all year round and a landfill-based final disposal system. Key elements for process design, such as wastewater pre-treatment, application method and rate, and the potential effects on leachate quantity and quality, are discussed based on a comprehensive literature review. Furthermore, a case-study for eight (8) olive mill enterprises generating 8700 m(3) of wastewater per year, was conceptually designed in order to calculate the capital and operational costs of the facility (transportation, storage, treatment, final disposal). The proposed facility was found to be economically self-sufficient, as long as the transportation costs of the OMW were maintained at ≤4.0 €/m(3). Despite that EU Landfill Directive prohibits wastewater disposal to landfills, controlled application, based on appropriately designed pre-treatment system and specific loading rates, may provide improved landfill stabilization and a sustainable (environmentally and economically) solution for effluents generated by numerous small- and medium-size olive mill enterprises dispersed in the Mediterranean region. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of site preparation treatments on early growth and survival of planted longleaf pine (Pinus palustris Mill.) seedlings in North Carolina

Treesearch

Benjamin O. Knapp; G. Geoff Wang; Joan L. Walker; Susan Cohen

2006-01-01

We tested the effects of eight site preparation treatments on early growth and survival of container-grown longleaf pine (Pinus palustris Mill.) seedlings. Treatments included an untreated check, six combinations of two initial vegetation control treatments (chopping or herbicide) with three planting site conditions (flat [no additional treatment],...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Metzler, D.; Gibb, J.P.; Glover, W.A.

Compliance with the mandate of the Uranium Mill Tailings Radiation Control Act (UMTRCA) at Uranium Mill Tailings Remedial Action (UMTRA) Project sites requires implementation of a groundwater remedial action plan that meets the requirements of Subpart B of the US Environmental Protection Agency`s proposed groundwater protection standards (40 CFR 192). The UMTRA Groundwater Project will ensure that unacceptable current risk or potential risk to the public health, safety and the environment resulting from the groundwater contamination attributable to the UMTRA sites, is mitigated in a timely and cost-efficient manner. For each UMTRA processing site and vicinity property where contamination exists,more » a groundwater remedial action plan must be developed that identifies hazardous constituents and establishes acceptable concentration limits for the hazardous constituents as either (a) alternate concentration limits (ACL), (b) maximum concentration limits (MCLs), (c) supplemental standards, or (d) background groundwater quality levels. Project optimization is a strategy that will aggressively work within the current regulatory framework using all available options to meet regulatory requirements. This strategy is outlined within.« less

76 FR 45300 - Notice of Issuance of Materials License SUA-1597 and Record of Decision for Uranerz Energy...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-28

... considered but eliminated from detailed analysis include conventional uranium mining and milling, conventional mining and heap leach processing, alternative site location, alternate lixiviants, and alternate...'s Agencywide Document Access and Management System (ADAMS), which provides text and image files of...

93. Photocopied August 1978 by the Harry S. Truman Library, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

93. Photocopied August 1978 by the Harry S. Truman Library, Independence, Missouri, from the original belonging to the Watkins Mill Historic Site. WATKINS MILL AS IT APPEARED C. 1910. - Watkins Mill, County Highway MM, Lawson, Ray County, MO

Historic mills and mill tailings as potential sources of contamination in and near the Humboldt River basin, northern Nevada. Chapter D.

USGS Publications Warehouse

Nash, J. Thomas; Stillings, Lisa L.

2003-01-01

Reconnaissance field studies of 40 mining districts in and near the Humboldt River basin have identified 83 mills and associated tailings impoundments and several other kinds of mineral-processing facilities (smelters, mercury retorts, heap-leach pads) related to historic mining. The majority of the mills and tailings sites are not recorded in the literature. All tailings impoundments show evidence of substantial amounts of erosion. At least 11 tailings dams were breached by flood waters, carrying fluvial tailings 1 to 15 km down canyons and across alluvial fans. Most of the tailings sites are dry most of the year, but some are near streams. Tailings that are wet for part of the year do not appear to be reacting significantly with those waters because physical factors such as clay layers and hard-pan cement appear to limit permeability and release of metals to surface waters. The major impact of mill tailings on surface- water quality may be brief flushes of runoff during storm events that carry acid and metals released from soluble mineral crusts. Small ephemeral ponds and puddles that tend to collect in trenches and low areas on tailings impoundments tend to be acidic and extremely enriched in metals, in part through cycles of evaporation. Ponded water that is rich in salts and metals could be acutely toxic to unsuspecting animals. Rare extreme storms have the potential to cause catastrophic failure of tailings impoundments, carry away metals in stormwaters, and transport tailings as debris flows for 1 to 15 km. In most situations these stormwaters and transported tailings could impact wildlife but probably would impact few or no people or domes-tic water wells. Because all identified historic tailings sites are several kilometers or more from the Humboldt River and major tributaries, tailings probably have no measurable impact on water quality in the main stem of the Humboldt River.

The Story of Story Mill-A Montana Community Working to Restore Wetlands

EPA Pesticide Factsheets

Story Mill, a 55-acre site on the outskirts of Bozeman, Montana, has undergone several transformations in recent history. The place is virtually a “mill of stories” with respect to land use, but originally it was a wetland.

Photomosaics and logs of trenches on the San Andreas Fault at Mill Canyon near Watsonville, California

USGS Publications Warehouse

Fumal, Thomas E.; Dawson, Timothy E.; Flowers, Rebecca; Hamilton, John C.; Heingartner, Gordon F.; Kessler, James; Samrad, Laura

2004-01-01

We present photomosaics and logs of the walls of trenches excavated for a paleoseismic study at Mill Canyon, one of two sites along the San Andreas fault in the Santa Cruz Mtns. on the Kelley-Thompson Ranch. This site was a part of Rancho Salsipuedes begining in 1834. It was purchased by the present owner’s family in 1851. Remnants of a cabin/mill operations still exist up the canyon dating from 1908 when the area was logged. At this location, faulting has moved a shutter ridge across the mouth of Mill Canyon ponding Holocene sediment. Recent faulting is confined to a narrow zone near the break in slope.

Bioethanol production from ball milled bagasse using an on-site produced fungal enzyme cocktail and xylose-fermenting Pichia stipitis.

PubMed

Buaban, Benchaporn; Inoue, Hiroyuki; Yano, Shinichi; Tanapongpipat, Sutipa; Ruanglek, Vasimon; Champreda, Verawat; Pichyangkura, Rath; Rengpipat, Sirirat; Eurwilaichitr, Lily

2010-07-01

Sugarcane bagasse is one of the most promising agricultural by-products for conversion to biofuels. Here, ethanol fermentation from bagasse has been achieved using an integrated process combining mechanical pretreatment by ball milling, with enzymatic hydrolysis and fermentation. Ball milling for 2 h was sufficient for nearly complete cellulose structural transformation to an accessible amorphous form. The pretreated cellulosic residues were hydrolyzed by a crude enzyme preparation from Penicillium chrysogenum BCC4504 containing cellulase activity combined with Aspergillus flavus BCC7179 preparation containing complementary beta-glucosidase activity. Saccharification yields of 84.0% and 70.4% for glucose and xylose, respectively, were obtained after hydrolysis at 45 degrees C, pH 5 for 72 h, which were slightly higher than those obtained with a commercial enzyme mixture containing Acremonium cellulase and Optimash BG. A high conversion yield of undetoxified pretreated bagasse (5%, w/v) hydrolysate to ethanol was attained by separate hydrolysis and fermentation processes using Pichia stipitis BCC15191, at pH 5.5, 30 degrees C for 24 h resulting in an ethanol concentration of 8.4 g/l, corresponding to a conversion yield of 0.29 g ethanol/g available fermentable sugars. Comparable ethanol conversion efficiency was obtained by a simultaneous saccharification and fermentation process which led to production of 8.0 g/l ethanol after 72 h fermentation under the same conditions. This study thus demonstrated the potential use of a simple integrated process with minimal environmental impact with the use of promising alternative on-site enzymes and yeast for the production of ethanol from this potent lignocellulosic biomass. 2009. Published by Elsevier B.V.

Process engineering with planetary ball mills.

PubMed

Burmeister, Christine Friederike; Kwade, Arno

2013-09-21

Planetary ball mills are well known and used for particle size reduction on laboratory and pilot scales for decades while during the last few years the application of planetary ball mills has extended to mechanochemical approaches. Processes inside planetary ball mills are complex and strongly depend on the processed material and synthesis and, thus, the optimum milling conditions have to be assessed for each individual system. The present review focuses on the insight into several parameters like properties of grinding balls, the filling ratio or revolution speed. It gives examples of the aspects of grinding and illustrates some general guidelines to follow for modelling processes in planetary ball mills in terms of refinement, synthesis' yield and contamination from wear. The amount of energy transferred from the milling tools to the powder is significant and hardly measurable for processes in planetary ball mills. Thus numerical simulations based on a discrete-element-method are used to describe the energy transfer to give an adequate description of the process by correlation with experiments. The simulations illustrate the effect of the geometry of planetary ball mills on the energy entry. In addition the imaging of motion patterns inside a planetary ball mill from simulations and video recordings is shown.

Effect of feed source and pyrolysis conditions on sugarcane bagasse biochar

USDA-ARS?s Scientific Manuscript database

Processing of sugarcane in sugar mills yield ca. 30% bagasse, a fibrous waste material composed mostly of crushed cane stalks. While 80-90% of the bagasse used on site as fuel, the remaining portion can be converted into a value-added product. One such option is thermal conversion of bagasse into bi...

System and method of forming nanostructured ferritic alloy

DOEpatents

Dial, Laura Cerully; DiDomizio, Richard; Alinger, Matthew Joseph; Huang, Shenyan

2016-07-26

A system for mechanical milling and a method of mechanical milling are disclosed. The system includes a container, a feedstock, and milling media. The container encloses a processing volume. The feedstock and the milling media are disposed in the processing volume of the container. The feedstock includes metal or alloy powder and a ceramic compound. The feedstock is mechanically milled in the processing volume using metallic milling media that includes a surface portion that has a carbon content less than about 0.4 weight percent.

1. VIEW, LOOKING WEST, AT THE SITE OF THE PINE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW, LOOKING WEST, AT THE SITE OF THE PINE LOG MILL. THE STONE RETAINING WALL ON THE RIGHT MARKS THE LOCATION OF THE 1896 20-STAMP FACILITY, EXPANDED SOUTH TO INCLUDE 20 ADDITIONAL STAMPS BY 1899 - Pine Log Mill, Southern Edge of Salt Spring Valley, Copperopolis, Calaveras County, CA

4. Long view of west half of site from Lawrence ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Long view of west half of site from Lawrence General Hospital parking deck (former location of coating mill) showing north side of rear portion of Wilder Mill and Paper Machine Building; view to southwest. - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

5. Long view of east half of site from Lawrence ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Long view of east half of site from Lawrence General Hospital parking deck (former location of coating mill) showing north side of Clay Storage Silos and northeast block of Wilder Mill; view to southwest. - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

Benefits of clean development mechanism application on the life cycle assessment perspective: a case study in the palm oil industry.

PubMed

Chuen, Onn Chiu; Yusoff, Sumiani

2012-03-01

This study performed an assessment on the beneficial of the Clean Development Mechanism (CDM) application on waste treatment system in a local palm oil industry in Malaysia. Life cycle assessment (LCA) was conducted to assess the environmental impacts of the greenhouse gas (GHG) reduction from the CDM application. Calculations on the emission reduction used the methodology based on AM002 (Avoided Wastewater and On-site Energy Use Emissions in the Industrial Sector) Version 4 published by United Nations Framework Convention on Climate Change (UNFCC). The results from the studies showed that the introduction of CDM in the palm oil mill through conversion of the captured biogas from palm oil mill effluent (POME) treatment into power generation were able to reduce approximate 0.12 tonnes CO2 equivalent concentration (tCO2e) emission and 30 kW x hr power generation per 1 tonne of fresh fruit bunch processed. Thus, the application of CDM methodology on palm oil mill wastewater treatment was able to reduce up to 1/4 of the overall environment impact generated in palm oil mill.

Investigation of the milling capabilities of the F10 Fine Grind mill using Box-Behnken designs.

PubMed

Tan, Bernice Mei Jin; Tay, Justin Yong Soon; Wong, Poh Mun; Chan, Lai Wah; Heng, Paul Wan Sia

2015-01-01

Size reduction or milling of the active is often the first processing step in the design of a dosage form. The ability of a mill to convert coarse crystals into the target size and size distribution efficiently is highly desirable as the quality of the final pharmaceutical product after processing is often still dependent on the dimensional attributes of its component constituents. The F10 Fine Grind mill is a mechanical impact mill designed to produce unimodal mid-size particles by utilizing a single-pass two-stage size reduction process for fine grinding of raw materials needed in secondary processing. Box-Behnken designs were used to investigate the effects of various mill variables (impeller, blower and feeder speeds and screen aperture size) on the milling of coarse crystals. Response variables included the particle size parameters (D10, D50 and D90), span and milling rate. Milled particles in the size range of 5-200 μm, with D50 ranging from 15 to 60 μm, were produced. The impeller and feeder speeds were the most critical factors influencing the particle size and milling rate, respectively. Size distributions of milled particles were better described by their goodness-of-fit to a log-normal distribution (i.e. unimodality) rather than span. Milled particles with symmetrical unimodal distributions were obtained when the screen aperture size was close to the median diameter of coarse particles employed. The capacity for high throughput milling of particles to a mid-size range, which is intermediate between conventional mechanical impact mills and air jet mills, was demonstrated in the F10 mill. Prediction models from the Box-Behnken designs will aid in providing a better guide to the milling process and milled product characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

88. Photocopied August 1978 by the Harry S. Truman Library, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

88. Photocopied August 1978 by the Harry S. Truman Library, Independence, Missouri, from the original belonging to the Watkins Mill Historic Site. HANDBILL WRITTEN BY WALTHUS L. WATKINS, ADVERTISING THE OPENING OF HIS MILL. DATED: MAY 8TH, 1861. - Watkins Mill, County Highway MM, Lawson, Ray County, MO

Summary of the engineering assessment of inactive uranium mill tailings, Durango Site, Durango, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-06-01

Ford, Bacon and Davis Utah Inc. has reevaluated the Durango site in order to revise the November 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Durango, Colorado. This engineering assessment has included the preparation of topographic measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the nearly 1.6 million tons of tailings at the Durango site constitutes the most significant environmental impact, although windblownmore » tailings and external gamma radiation also are factors. The four alternative actions presented in this engineering assessment range from millsite and off-site decontamination with the addition of 3 m of stabilization cover material (Option I), to removal of the tailings to remote disposal sites and decontamination of the tailings site (Options II through IV). Cost estimates for the seven options range from about $10,700,000 for stabilization in-place, to about $21,800,000 for disposal at a distance of about 10 mi. Three principal alternatives for the reprocessing of the Durango tailings were examined: (a) heap leaching; (b) treatment at an existing mill; and (c) reprocessing at a new conventional mill constructed for tailings reprocessing.« less

OVERVIEW OF STAMP MILL SITE,LOOKING SOUTHWEST. THE LOWER TRAM TERMINAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERVIEW OF STAMP MILL SITE,LOOKING SOUTHWEST. THE LOWER TRAM TERMINAL IS OUT OF FRAME, JUST TO THE RIGHT. WATER TANK, LOADING PLATFORM, AND TRAM TRESTLE LEADING UP TO THE TRAM TERMINAL ARE AT RIGHT. THE STRUCTURE AT EXTREME RIGHT BELOW THE TRESTLE, ARE REMAINS OF A SECONDARY ORE BIN, WITH BALL MILL FOUNDATIONS AND WOOD DEBRIS JUST BELOW ON THE SECOND LEVEL. AT CENTER IS A BOILER AND THE FRAME WORK OF A FILTER PRESS. THE SMALL STRUCTURE AT CENTER LEFT IS AN INTERPRETIVE SIGN PLACED BY THE PARK SERVICE. AT LOWER LEFT, THIRD LEVEL OF THE MILL, ARE THE REMAINS OF A BLACKSMITH'S FORGE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Nuclear facility decommissioning and site remedial actions: A selected bibliography, Volume 18. Part 1B: Citations with abstracts, sections 10 through 16

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-09-01

This bibliography contains 3,638 citations with abstracts of documents relevant to environmental restoration, nuclear facility decontamination and decommissioning (D and D), uranium mill tailings management, and site remedial actions. The bibliography contains scientific, technical, financial, and regulatory information that pertains to DOE environmental restoration programs. The citations are separated by topic into 16 sections, including (1) DOE Environmental Restoration Program; (2) DOE D and D Program; (3) Nuclear Facilities Decommissioning; (4) DOE Formerly Utilized sites Remedial Action Program; (5) NORM-Contaminated Site Restoration; (6) DOE Uranium Mill Tailings Remedial Action Project; (7) Uranium Mill Tailings Management; (8) DOE Site-Wide Remedial Actions;more » (9) DOE Onsite Remedial Action Projects; (10) Contaminated Site Remedial Actions; (11) DOE Underground Storage Tank Remediation; (12) DOE Technology Development, Demonstration, and Evaluation; (13) Soil Remediation; (14) Groundwater Remediation; (15) Environmental Measurements, Analysis, and Decision-Making; and (16) Environmental Management Issues.« less

BLENDING LOW ENRICHED URANIUM WITH DEPLETED URANIUM TO CREATE A SOURCE MATERIAL ORE THAT CAN BE PROCESSED FOR THE RECOVERY OF YELLOWCAKE AT A CONVENTIONAL URANIUM MILL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schutt, Stephen M.; Hochstein, Ron F.; Frydenlund, David C.

2003-02-27

Throughout the United States Department of Energy (DOE) complex, there are a number of streams of low enriched uranium (LEU) that contain various trace contaminants. These surplus nuclear materials require processing in order to meet commercial fuel cycle specifications. To date, they have not been designated as waste for disposal at the DOE's Nevada Test Site (NTS). Currently, with no commercial outlet available, the DOE is evaluating treatment and disposal as the ultimate disposition path for these materials. This paper will describe an innovative program that will provide a solution to DOE that will allow disposition of these materials atmore » a cost that will be competitive with treatment and disposal at the NTS, while at the same time recycling the material to recover a valuable energy resource (yellowcake) for reintroduction into the commercial nuclear fuel cycle. International Uranium (USA) Corporation (IUSA) and Nuclear Fuel Services, Inc. (NFS) have entered into a commercial relationship to pursue the development of this program. The program involves the design of a process and construction of a plant at NFS' site in Erwin, Tennessee, for the blending of contaminated LEU with depleted uranium (DU) to produce a uranium source material ore (USM Ore{trademark}). The USM Ore{trademark} will then be further processed at IUC's White Mesa Mill, located near Blanding, Utah, to produce conventional yellowcake, which can be delivered to conversion facilities, in the same manner as yellowcake that is produced from natural ores or other alternate feed materials. The primary source of feed for the business will be the significant sources of trace contaminated materials within the DOE complex. NFS has developed a dry blending process (DRYSM Process) to blend the surplus LEU material with DU at its Part 70 licensed facility, to produce USM Ore{trademark} with a U235 content within the range of U235 concentrations for source material. By reducing the U235 content to source material levels in this manner, the material will be suitable for processing at a conventional uranium mill under its existing Part 40 license to remove contaminants and enable the product to re-enter the commercial fuel cycle. The tailings from processing the USM Ore{trademark} at the mill will be permanently disposed of in the mill's tailings impoundment as 11e.(2) byproduct material. Blending LEU with DU to make a uranium source material ore that can be returned to the nuclear fuel cycle for processing to produce yellowcake, has never been accomplished before. This program will allow DOE to disposition its surplus LEU and DU in a cost effective manner, and at the same time provide for the recovery of valuable energy resources that would be lost through processing and disposal of the materials. This paper will discuss the nature of the surplus LEU and DU materials, the manner in which the LEU will be blended with DU to form a uranium source material ore, and the legal means by which this blending can be accomplished at a facility licensed under 10 CFR Part 70 to produce ore that can be processed at a conventional uranium mill licensed under 10 CFR Part 40.« less

Wind Resource Assessment Report: Mille Lacs Indian Reservation, Minnesota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jimenez, Antonio C.; Robichaud, Robi

The U.S. Environmental Protection Agency (EPA) launched the RE-Powering America's Land initiative to encourage development of renewable energy on potentially contaminated land and mine sites. EPA collaborated with the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) and the Mille Lacs Band of Chippewa Indians to evaluate the wind resource and examine the feasibility of a wind project at a contaminated site located on the Mille Lacs Indian Reservation in Minnesota. The wind monitoring effort involved the installation of a 60-m met tower and the collection of 18 months of wind data at multiple heights above the ground.more » This report focuses on the wind resource assessment, the estimated energy production of wind turbines, and an assessment of the economic feasibility of a potential wind project sited this site.« less

29 CFR 788.11 - “Transporting [such] products to the mill, processing plant, railroad, or other transportation...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false âTransporting [such] products to the mill, processing plant... EMPLOYED § 788.11 “Transporting [such] products to the mill, processing plant, railroad, or other transportation terminal.” The transportation or movement of logs or other forestry products to a “mill processing...

8. John and James Dobson Carpet Mill, East and West ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. John and James Dobson Carpet Mill, East and West Parcels, site plan, and survey lower left, 1865. Hexamer, Ernest and Son. Hexamer General Surveys, 1867-1895, Philadelphia, Pennsylvania: E. Hexamer and Son, 1865, p. 279. - John & James Dobson Carpet Mill (West Parcel), 4041-4055 Ridge Avenue, Philadelphia, Philadelphia County, PA

The Economics of Authorship: Online Paper Mills, Student Writers, and First-Year Composition

ERIC Educational Resources Information Center

Ritter, Kelly

2005-01-01

Using sample student analyses of online paper mill Web sites, student survey responses, and existing scholarship on plagiarism, authorship, and intellectual property, this article examines how the consumerist rhetoric of the online paper mills construes academic writing as a commodity for sale, and why such rhetoric appeals to students in…

TRANSPORT AND FATE OF AMMONIUM AND ITS IMPACT ON URANIUM AND OTHER TRACE ELEMENTS AT A FORMER URANIUM MILL TAILING SITE

PubMed Central

Miao, Ziheng; Nihat, Hakan; McMillan, Andrew Lee; Brusseau, Mark L.

2013-01-01

The remediation of ammonium-containing groundwater discharged from uranium mill tailing sites is a difficult problem facing the mining industry. The Monument Valley site is a former uranium mining site in the southwest US with both ammonium and nitrate contamination of groundwater. In this study, samples collected from 14 selected wells were analyzed for major cations and anions, trace elements, and isotopic composition of ammonium and nitrate. In addition, geochemical data from the U.S. Department of Energy (DOE) database were analyzed. Results showing oxic redox conditions and correspondence of isotopic compositions of ammonium and nitrate confirmed the natural attenuation of ammonium via nitrification. Moreover, it was observed that ammonium concentration within the plume area is closely related to concentrations of uranium and a series of other trace elements including chromium, selenium, vanadium, iron, and manganese. It is hypothesized that ammonium-nitrate transformation processes influence the disposition of the trace elements through mediation of redox potential, pH, and possibly aqueous complexation and solid-phase sorption. Despite the generally relatively low concentrations of trace elements present in groundwater, their transport and fate may be influenced by remediation of ammonium or nitrate at the site. PMID:24357895

Results of the independent verification of radiological remedial action at 397 East 3rd South Street, Monticello, Utah (MS00168)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, M.J.; Crutcher, J.W.

1991-07-01

In 1980 the site of a vanadium and uranium mill at Monticello, Utah, was accepted into the US Department of Energy's (DOE's) Surplus Facilities Management Program, with the objectives of restoring the government-owned mill site to safe levels of radioactivity, disposing of or containing the tailings in an environmentally safe manner, and performing remedial actions on off-site (vicinity) properties that had been contaminated by radioactive material resulting from mill operations. During 1987 and 1988, UNC Geotech, the remedial action contractor designated by DOE, performed remedial action on the vicinity property at 397 East 3rd South Street, Monticello, Utah. The Pollutantmore » Assessments Group (PAG) of Oak Ridge National Laboratory was assigned the responsibility of verifying the data supporting the adequacy of remedial action and confirming the site's compliance with DOE guidelines. The PAG found that the site successfully meets the DOE remedial action objectives. Procedures used by PAG are described. 3 refs., 2 tabs.« less

Results of the independent verification of radiological remedial action at 464 South 1st East Street, Monticello, Utah (MS00071)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, M.J.; Crutcher, J.W.

1991-07-01

In 1980 the site of a vanadium and uranium mill at Monticello, Utah, was accepted into the US Department of Energy's (DOE's) Surplus Facilities Management Program, with the objectives of restoring the government-owned mill site to safe levels of radioactivity, disposing of or containing the tailings in an environmentally safe manner, and performing remedial actions on off-site (vicinity) properties that had been contaminated by radioactive material resulting from mill operations. During 1986 and 1987, UNC Geotech, the remedial action contractor designated by DOE, performed remedial action on the vicinity property at 464 South 1st East Street, Monticello, Utah. The Pollutantmore » Assessments Group (PAG) of Oak Ridge National Laboratory was assigned the responsibility of verifying the data supporting the adequacy of remedial action and confirming the site's compliance with DOE guidelines. The PAG found that the site successfully meets the DOE remedial action objectives. Procedures used by PAG are described. 3 refs., 2 tabs.« less

Results of the independent verification of radiological remedial action at 16 East 5th South Street, Monticello, Utah (MS00075)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, M.J.; Crutcher, J.W.

1991-07-01

In 1980 the site of a vanadium and uranium mill at Monticello, Utah, was accepted into the US Department of Energy's (DOE's) Surplus Facilities Management Program, with the objectives of restoring the government-owned mill site to safe levels of radioactivity, disposing of or containing the tailings in an environmentally safe manner, and performing remedial actions on off-site (vicinity) properties that had been contaminated by radioactive material resulting from mill operations. During 1984 UNC Geotech, the remedial action contractor designated by DOE, performed remedial action on the vicinity property at 16 East 5th South Street, Monticello, Utah. The Pollutant Assessments Groupmore » (PAG) of Oak Ridge National Laboratory was assigned the responsibility of verifying the data supporting the adequacy of remedial action and confirming the site's compliance with DOE guidelines. The PAG found that the site successfully meets the DOE remedial action objectives. Procedures used by PAG are described. 3 refs., 2 tabs.« less

11. John and James Dobson Carpet Mill, East and West ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. John and James Dobson Carpet Mill, East and West parcels, site plan-upper left, elevation-lower left, and survey-right, 1877. Hexamer, Ernest and Son. Hexamer General Surveys, 1867-1895, Philadelphia, Pennsylvania: E. Hexamer and Son, 1877, pp. 1095-1096. - John & James Dobson Carpet Mill (West Parcel), 4041-4055 Ridge Avenue, Philadelphia, Philadelphia County, PA

13. John and James Dobson Carpet Mill, East and West ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. John and James Dobson Carpet Mill, East and West parcels, site plan-upper left, elevation-upper right, and survey-below, 1885. Hexamer, Ernest and Son. Hexamer General Surveys, 1867-1895, Philadelphia, Pennsylvania: E. Hexamer and Son, 1885, pp. 1890-1891. - John & James Dobson Carpet Mill (West Parcel), 4041-4055 Ridge Avenue, Philadelphia, Philadelphia County, PA

9. John and James Dobson Carpet Mill, portion of West ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. John and James Dobson Carpet Mill, portion of West parcel, site plan-left, elevation-upper right, and survey-lower right, 1873. Hexamer, Ernest and Son. Hexamer General Surveys 1867-1895, Philadelphia, Pennsylvania: E. Hexamer and Son, 1873, pp. 670-671. - John & James Dobson Carpet Mill (West Parcel), 4041-4055 Ridge Avenue, Philadelphia, Philadelphia County, PA

Biota of uranium mill tailings near the Black Hills

Treesearch

Mark A. Rumble

1982-01-01

Reclamation" often implies the enhancement of the land as wildlife habitat or for other productive uses. However, there are situations where revegetation to stabilize erosion is the only desired goal. Uranium mining and mill sites may fall into this later category. Data pertaining to plant and animal components on revegetated uranium mill tailings was collected....

The kinetics of composite particle formation during mechanical alloying

NASA Technical Reports Server (NTRS)

Aikin, B. J. M.; Courtney, T. H.

1993-01-01

The kinetics of composite particle formation during attritor milling of insoluble binary elemental powders have been examined. The effects of processing conditions (i.e., mill power, temperature, and charge ratio) on these kinetics were studied. Particle size distributions and fractions of elemental and composite particles were determined as functions of milling time and processing conditions. This allowed the deduction of phenomenological rate constants describing the propensity for fracture and welding during processing. For the mill-operating conditions investigated, the number of particles in the mill generally decreased with milling time, indicating a greater tendency for particle welding than fracture. Moreover, a bimodal size distribution is often obtained as a result of preferential welding. Copper and chromium 'alloy' primarily by encapsulation of Cr particles within Cu. This form of alloying also occurs in Cu-Nb alloys processed at low mill power and/or for short milling times. For other conditions, however, Cu-Nb alloys develop a lamellar morphology characteristic of mechanically alloyed two-phase ductile metals. Increasing mill power or charge (ball-to-powder weight) ratio (CR) increases the rate of composite particle formation.

The yellowed archives of yellowcake.

PubMed Central

Silver, K

1996-01-01

Extensive historical documentation of exposures and releases at government-owned energy facilities is a unique and valuable resource for analyzing and communicating health risks. Facilities at all stages of the atomic fuel cycle were the subject of numerous industrial hygiene, occupational health, and environmental assessments during the Cold War period. Uranium mines and mills on the Colorado Plateau were investigated as early as the 1940s. One such facility was the mill in Monticello, Utah, which began operation as a vanadium extraction plant in 1943 and was later adapted to recover uranium from carnotite ores. The mill ceased operation in 1960. The site was added to the federal Superfund list in 1986. ATSDR held public availability sessions in 1993 as part of its public health assessment process, at which several former mill workers voiced health concerns. An extensive literature search yielded several industrial hygiene evaluations of the Monticello mill and health studies that included Monticello workers, only two of which had been published in the peer-reviewed literature. In combination with the broader scientific literature, these historical reports provide a partial basis for responding to mill workers' contemporary health concerns. The strengths and limitations of the available exposure data for analytical epidemiologic studies and dose reconstruction are discussed. As an interim measure, the available historical documentation may be especially helpful in communicating about health risks with workers and communities in ways that acknowledge the historical context of their experience. Images p116-a p117-a p118-a PMID:8606907

10 CFR 40.28 - General license for custody and long-term care of uranium or thorium byproduct materials disposal...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false General license for custody and long-term care of uranium... long-term care of uranium or thorium byproduct materials disposal sites. (a) A general license is... in this part for uranium or thorium mill tailings sites closed under title II of the Uranium Mill...

10 CFR 40.28 - General license for custody and long-term care of uranium or thorium byproduct materials disposal...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false General license for custody and long-term care of uranium... long-term care of uranium or thorium byproduct materials disposal sites. (a) A general license is... in this part for uranium or thorium mill tailings sites closed under title II of the Uranium Mill...

10 CFR 40.28 - General license for custody and long-term care of uranium or thorium byproduct materials disposal...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false General license for custody and long-term care of uranium... long-term care of uranium or thorium byproduct materials disposal sites. (a) A general license is... in this part for uranium or thorium mill tailings sites closed under title II of the Uranium Mill...

10 CFR 40.28 - General license for custody and long-term care of uranium or thorium byproduct materials disposal...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false General license for custody and long-term care of uranium... long-term care of uranium or thorium byproduct materials disposal sites. (a) A general license is... in this part for uranium or thorium mill tailings sites closed under title II of the Uranium Mill...

Influence of attrition milling on nano-grain boundaries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rawers, J.; Cook, D.

1999-03-01

Nanostructured materials have a relatively large proportion of their atoms associated with the grain boundary, and the method used to develop the nano-grains has a strong influence on the resulting grain boundary structure. In this study, attrition milling iron powders and blends of iron powders produced micron-size particles composed of nano-size grains. Mechanical cold-working powder resulted in dislocation generation, multiplication, and congealing that produced grain refinement. As the grain size approached nano-dimensions, dislocations were no longer sustained within the grain and once generated, rapidly diffused to the grain boundary. Dislocations on the grain boundary strained the local lattice structure which,more » as the grain size decreased, became the entire grain. Mechanical alloying of substitutional aluminium atoms into iron powder resulted in the aluminium atoms substituting for iron atoms in the grain boundary cells and providing a grain boundary structure similar to that of the iron powder processed in argon. Attrition milling iron powder in nitrogen gas resulted in nitrogen atoms being adsorbed onto the particle surface. Continued mechanical milling infused the nitrogen atoms into interstitial lattice sites on the grain boundary which also contributed to expanding and straining the local lattice.« less

The path back: oaks ( Quercus spp.) facilitate longleaf pine ( Pinus palustris ) seedling establishment in xeric sites

Treesearch

E. Louise Loudermilk; J. Kevin Hiers; Scott Pokswinski; Joseph J. O' Brien; Analie Barnett; Robert J. Mitchell

2016-01-01

Understanding plant–plant facilitation is critical for predicting how plant community function will respond to changing disturbance and climate. In longleaf pine (Pinus palustris Mill.) ecosystems of the southeastern United States, understanding processes that affect pine reproduction is imperative for conservation efforts that aim to maintain...

3. VIEW EAST OF MILL STREET BUILDINGS; 20 AT EXTREME ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. VIEW EAST OF MILL STREET BUILDINGS; 20 AT EXTREME LEFT CENTER; 21 AT MID-LEFT CENTER; 4 AT LEFT CENTER; RUNDBOGENSTIL TOWER AT CENTER; BUILDING 3 RIGHT CENTER; BUILDING 2 AT EXTREME RIGHT CENTER; BUILDING 3 IS THE OLDEST BUILDING ON SITE AND WAS BUILT CIRCA 1850 - Scovill Brass Works, 59 Mill Street, Waterbury, New Haven County, CT

19. View of Andrew McLean Company Textile Mill looking south; ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. View of Andrew McLean Company Textile Mill looking south; Building No. 2 at center, Botany Mills Lanolin Retrieval plant site in foreground - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

Microstructural characterization of low and high carbon CoCrMo alloy nanoparticles produced by mechanical milling

NASA Astrophysics Data System (ADS)

Simoes, T. A.; Goode, A. E.; Porter, A. E.; Ryan, M. P.; Milne, S. J.; Brown, A. P.; Brydson, R. M. D.

2014-06-01

CoCrMo alloys are utilised as the main material in hip prostheses. The link between this type of hip prosthesis and chronic pain remains unclear. Studies suggest that wear debris generated in-vivo may be related to post-operative complications such as inflammation. These alloys can contain different amounts of carbon, which improves the mechanical properties of the alloy. However, the formation of carbides could become sites that initiate corrosion, releasing ions and/or particles into the human body. This study analysed the mechanical milling of alloys containing both high and low carbon levels in relevant biological media, as an alternative route to generate wear debris. The results show that low carbon alloys produce significantly more nanoparticles than high carbon alloys. During the milling process, strain induces an fcc to hcp phase transformation. Evidence for cobalt and molybdenum dissolution in the presence of serum was confirmed by ICP-MS and TEM EDX techniques.

Microstructure and magnetic properties of MFe2O4 (M = Co, Ni, and Mn) ferrite nanocrystals prepared using colloid mill and hydrothermal method

NASA Astrophysics Data System (ADS)

Wang, Wei; Ding, Zui; Zhao, Xiruo; Wu, Sizhu; Li, Feng; Yue, Ming; Liu, J. Ping

2015-05-01

Three kinds of spinel ferrite nanocrystals, MFe2O4 (M = Co, Ni, and Mn), are synthesized using colloid mill and hydrothermal method. During the synthesis process, a rapid mixing and reduction of cations with sodium borohydride (NaBH4) take place in a colloid mill then through a hydrothermal reaction, a slow oxidation and structural transformation of the spinel ferrite nanocrystals occur. The phase purity and crystal lattice parameters are estimated by X-ray diffraction studies. Scanning electron microscopy and transmission electron microscopy images show the morphology and particle size of the as-synthesized ferrite nanocrystals. Raman spectrum reveals active phonon modes at room temperature, and a shifting of the modes implies cation redistribution in the tetrahedral and octahedral sites. Magnetic measurements show that all the obtained samples exhibit higher saturation magnetization (Ms). Meanwhile, experiments demonstrate that the hydrothermal reaction time has significant effects on microstructure, morphologies, and magnetic properties of the as-synthesized ferrite nanocrystals.

Environmental Assessment of remedial action at the Ambrosia Lake uranium mill tailings site, Ambrosia Lake, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-06-01

This document assesses and compares the environmental impacts of various alternatives for remedial action at the Ambrosia Lake uranium mill tailings site located near Ambrosia Lake, New Mexico. The designated site covers 196 acres and contains 111 acres of tailings and some of the original mill structures. The Uranium Mill Tailings Radiation Control Act (UMTRCA), Public Law 95-604, authorizes the US Department of Energy to clean up the site to reduce the potential health impacts associated with the residual radioactive materials remaining at the site and at associated properties off the site. The US Environmental Protection Agency promulgated standards formore » th remedial action (40 CFR Part 192). Remedial action must be performed in accordance with these standards and with the concurrence of the Nuclear Regulatory Commission. The proposed action is to stabilize the tailings at their present location by consolidating the tailings and associated contaminated materials into a recontoured pile. A radon barrier would be constructed over the pile and various erosion protection measures would be taken to assure the long-term stability of the pile. Another alternative which would involve moving the tailings to a new location is also assessed in this document. This alternative would generally involve greater short-term impacts and costs but would result in stabilization of the tailings at an undeveloped location. The no action alternative is also assessed in this document.« less

Directional genetic selection by pulp mill effluent on multiple natural populations of three-spined stickleback (Gasterosteus aculeatus).

PubMed

Lind, Emma E; Grahn, Mats

2011-05-01

Contamination can cause a rapid environmental change which may require populations to respond with evolutionary changes. To evaluate the effects of pulp mill effluents on population genetics, we sampled three-spined sticklebacks (Gasterosteus aculeatus) near four pulp mills and four adjacent reference sites and analyzed Amplified Fragment Length Polymorphism (AFLP) to compare genetic variability. A fine scale genetic structure was detected and samples from polluted sites separated from reference sites in multidimensional scaling plots (P<0.005, 1000 permutations) and locus-by-locus Analysis of Molecular Variance (AMOVA) further confirmed that habitats are significantly separated (F(ST)=0.021, P<0.01, 1023 permutations). The amount of genetic variation between populations did not differ between habitats, and populations from both habitats had similar levels of heterozygosity (polluted sites Nei's Hs=0.11, reference sites Nei's Hs=0.11). Still, pairwise F(ST): s between three, out of four, pairs of polluted-reference sites were significant. A F(ST)-outlier analysis showed that 21 (8.4%) loci were statistically different from a neutral distribution at the P<0.05 level and therefore indicated to be under divergent selection. When removing 13 F(ST)-outlier loci, significant at the P<0.01 level, differentiation between habitats disappeared in a multidimensional scaling plot. In conclusion, pulp mill effluence has acted as a selective agent on natural populations of G. aculeatus, causing a convergence in genotype composition change at multiple sites in an open environment. © The Author(s) 2011. This article is published with open access at Springerlink.com

Environmental assessment of remedial action at the Gunnison Uranium Mill Tailings Site, Gunnison, Colorado. [UMTRA Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bachrach, A.; Hoopes, J.; Morycz, D.

1984-12-01

This document assesses and compares the environmental impacts of various alternatives for remedial action at the Gunnison uranium of mill tailings site located 0.5 miles south of Gunnison, Colorado. The site covers 56 acres and contains 35 acres of tailings, 2 of the original mill buildings and a water tower. The Uranium Mill Tailings Radiation Control of Act of 1978 (UMTRCA), Public Law 95-604, authorizes the US Department of Energy to clean up the site to reduce the potential health impacts associated with the residual radioactive materials remaining at the site and at associated (vicinity) properties off the site. Themore » US Environmental Protection Agency promulgated standards for the remedial actions (40 CFR 192). Remedial actions must be performed in accordance with these standards and with the occurrence of the Nuclear Regulatory Commission. Four alternatives have been addressed in this document. The first alternative is to consolidate the tailings and associated contaminated soils into a recontoured pile on the southern portion of the existing site. A radon barrier of silty clay would be constructed over the pile and various erosion control measures would be taken to assure the long-term integrity of the pile. Two other alternatives which involve moving the tailings to new locations are assessed in this document. These alternatives generally involve greater short-term impacts and are more costly but would result in the tailings being stabilized in a location farther from the city of Gunnison. The no action alternative is also assessed.« less

West Virginia timber industry: an assessment of timber product output and use, 2007

Treesearch

Ronald J. Piva; Gregory W. Cook

2011-01-01

In 2007, there were 116 primary wood-processing mills in West Virginia, 60 fewer mills than in 2000. These mills processed 172.9 million cubic feet of industrial roundwood, of which 138.8 million cubic feet was harvested from the State. Another 50.5 million cubic feet of the industrial roundwood harvested in West Virginia was sent to primary wood-processing mills in...

Transport and Sources of Suspended Sediment in the Mill Creek Watershed, Johnson County, Northeast Kansas, 2006-07

USGS Publications Warehouse

Lee, Casey J.; Rasmussen, Patrick P.; Ziegler, Andrew C.; Fuller, Christopher C.

2009-01-01

The U.S. Geological Survey, in cooperation with the Johnson County Stormwater Management Program, evaluated suspended-sediment transport and sources in the urbanizing, 57.4 mi2 Mill Creek watershed from February 2006 through June 2007. Sediment transport and sources were assessed spatially by continuous monitoring of streamflow and turbidity as well as sampling of suspended sediment at nine sites in the watershed. Within Mill Creek subwatersheds (2.8-16.9 mi2), sediment loads at sites downstream from increased construction activity were substantially larger (per unit area) than those at sites downstream from mature urban areas or less-developed watersheds. Sediment transport downstream from construction sites primarily was limited by transport capacity (streamflow), whereas availability of sediment supplies primarily influenced transport downstream from mature urban areas. Downstream sampling sites typically had smaller sediment loads (per unit area) than headwater sites, likely because of sediment deposition in larger, less sloping stream channels. Among similarly sized storms, those with increased precipitation intensity transported more sediment at eight of the nine monitoring sites. Storms following periods of increased sediment loading transported less sediment at two of the nine monitoring sites. In addition to monitoring performed in the Mill Creek watershed, sediment loads were computed for the four other largest watersheds (48.6-65.7 mi2) in Johnson County (Blue River, Cedar, Indian, and Kill Creeks) during the study period. In contrast with results from smaller watersheds in Mill Creek, sediment load (per unit area) from the most urbanized watershed in Johnson County (Indian Creek) was more than double that of other large watersheds. Potential sources of this sediment include legacy sediment from earlier urban construction, accelerated stream-channel erosion, or erosion from specific construction sites, such as stream-channel disturbance during bridge renovation. The implication of this finding is that sediment yields from larger watersheds may remain elevated after the majority of urban development is complete. Surface soil, channel-bank, suspended-sediment, and streambed-sediment samples were analyzed for grain size, nutrients, trace elements, and radionuclides in the Mill Creek watershed to characterize suspended sediment between surface or channel-bank sources. Although concentrations and activities of cobalt, nitrogen, selenium, total organic carbon, cesium-137, and excess lead-210 had significant differences between surface and channel-bank samples, biases resulting from urban construction, additional sorption of constituents during sediment transport, and inability to accurately represent erosion from rills and gullies precluded accurate characterization of suspended-sediment source.

Ball milling pretreatment of corn stover for enhancing the efficiency of enzymatic hydrolysis.

PubMed

Lin, Zengxiang; Huang, He; Zhang, Hongman; Zhang, Lin; Yan, Lishi; Chen, Jingwen

2010-11-01

Ethanol can be produced from lignocellulosic biomass with the usage of ball milling pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields from lignocellulosic feed stocks are critical parameters for ethanol production process. The research results from this paper indicated that the yields of glucose and xylose were improved by adding any of the following dilute chemical reagents: H(2)SO(4), HCl, HNO(3), CH(3)COOH, HCOOH, H(3)PO(4), and NaOH, KOH, Ca(OH)(2), NH(3)·H(2)O in the ball milling pretreatment of corn stover. The optimal enzymatic hydrolysis efficiencies were obtained under the conditions of ball milling in the alkali medium that was due to delignification. The data also demonstrated that ball milling pretreatment was a robust process. From the microscope image of ball milling-pretreated corn stover, it could be observed that the particle size of material was decreased and the fiber structure was more loosely organized. Meanwhile, the results indicate that the treatment effect of wet milling is better than that of dry milling. The optimum parameters for the milling process were ball speed of 350 r/min, solid/liquid ratio of 1:10, raw material particle size with 0.5 mm, and number of balls of 20 (steel ball, Φ = 10 mm), grinding for 30 min. In comparison with water milling process, alkaline milling treatment could increase the enzymatic hydrolysis efficiency of corn stover by 110%; and through the digestion process with the combination of xylanase and cellulase mixture, the hydrolysis efficiency could increase by 160%.

Column Testing and 1D Reactive Transport Modeling to Evaluate Uranium Plume Persistence Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Raymond H.; Morrison, Stan; Morris, Sarah

Motivation for Study: Natural flushing of contaminants at various U.S. Department of Energy Office of Legacy Management sites is not proceeding as quickly as predicted (plume persistence) Objectives: Help determine natural flushing rates using column tests. Use 1D reactive transport modeling to better understand the major processes that are creating plume persistence Approach: Core samples from under a former mill tailings area Tailings have been removed. Column leaching using lab-prepared water similar to nearby Gunnison River water. 1D reactive transport modeling to evaluate processes

89. Photocopied August 1978 by the Harry S. Truman Library, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

89. Photocopied August 1978 by the Harry S. Truman Library, Independence, Missouri, from the original belonging to the Watkins Mill Historic Site. WALTHUS L. WATKINS. - Watkins Mill, County Highway MM, Lawson, Ray County, MO

U.S. Geological Survey research in radioactive waste disposal - Fiscal years 1986-1990

USGS Publications Warehouse

Trask, N.J.; Stevens, P.R.

1991-01-01

The report summarizes progress on geologic and hydrologic research related to the disposal of radioactive wastes. The research efforts are categorized according to whether they are related most directly to: (1) high-level wastes, (2) transuranic wastes, (3) low-level and mixed low-level and hazardous wastes, or (4) uranium mill tailings. Included is research applicable to the identification and geohydrologic characterization of waste-disposal sites, to investigations of specific sites where wastes have been stored, to development of techniques and methods for characterizing disposal sites, and to studies of geologic and hydrologic processes related to the transport and/or retention of waste radionuclides.

Results of the independent verification of radiological remedial action at 87 East 500 South Street, Monticello, Utah (MS00153)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, M.J.; Crutcher, J.W.

1991-07-01

In 1980 the iste of a vanadium and uranium mill at Monticello, Utah, was accepted into the US Department of Energy's (DOE's) Surplus Facilities Management Program, with the objectives of restoring the government-owned mill site to safe levels of radioactivity, disposing of or containing the tailings in an environmentally safe manner, and performing remedial actions on off-site (vicinity) properties that had been contaminated by radioactive material resulting from mill operations. During 1987 and 1988, UNC Geotech, the remedial action contractor designated by DOE, performed remedial action on the vicinity property at 87 East 500 South Street, Monticello, Utah. The Pollutantmore » Assessments Group (PAG) of Oak Ridge National Laboratory was assigned the responsibility of verifying the data supporting the adequacy of remedial action and confirming the site's compliance with DOE guidelines. The PAG found that the site successfully meets the DOE remedial action objectives. Procedures used by PAG are described. 3 refs., 2 tabs.« less

Results of the independent verification of radiological remedial action at 600 South Clayhill Drive (AKA 600 South Cemetery Road), Monticello, Utah (MS00145)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, M.J.; Crutcher, J.W.

1991-07-01

In 1980 the site of a vanadium and uranium mill at Monticello, Utah, was accepted into the US Department of Energy's (DOE's) Surplus Facilities Management Program, with the objectives of restoring the government-owned mill site to safe levels of radioactivity, disposing of or containing the tailings in an environmentally safe manner, and performing remedial actions on off-site (vicinity) properties that had been contaminated by radioactive material resulting from mill operations. During 1986 and 1987, UNC Geotech, the remedial action contractor designated by DOE, performed remedial action on the vicinity property at 600 South Cemetery Road (updated by San Juan Countymore » and the state of Utah to 600 South Clayhill Drive), Monticello, Utah. The Pollutant Assessments Group (PAG) of Oak Ridge National Laboratory was assigned the responsibility of verifying the data supporting the adequacy of remedial action and confirming the site's compliance with DOE guidelines. The PAG found that the site successfully meets the DOE remedial action objectives. Procedures used by PAG are described. 3 refs., 2 tabs.« less

Cleanup protocol for 226Ra-contaminated cobbly soil at UMTRA Project sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonzales, D.E.; Millard, J.B.; Miller, M.L.

The nonuniform distribution of 226Ra and other radiological contamination of cobbly soil encountered on several Uranium Mill Tailings Remedial Action Project sites is presented and discussed, and the concomitant challenges to the intent and implementation of the U.S. Environmental Protection Agency's soil cleanup standards are noted. In response to technical assessments and information presented to the U.S. Nuclear Regulatory Commission by the U.S. Department of Energy, the Nuclear Regulatory Commission has recently resolved the dilemma by concluding that compliance with Environmental Protection Agency soil cleanup standards for cobby soil at Uranium Mill Tailings Remedial Action Project sites would be adequatelymore » attained using bulk radionuclide concentrations, instead of requiring that the radionuclide concentration of the finer soil fraction passing a No. 4 mesh sieve met the standards. A Nuclear Regulatory Commission-approved procedure developed for cobbly soil remediation is outlined and discussed. The site-specific implementation of this procedure at Uranium Mill Tailings Remedial Action Project sites containing cobbly soil is estimated to save millions of dollars.« less

Matrix model of the grinding process of cement clinker in the ball mill

NASA Astrophysics Data System (ADS)

Sharapov, Rashid R.

2018-02-01

In the article attention is paid to improving the efficiency of production of fine powders, in particular Portland cement clinker. The questions of Portland cement clinker grinding in closed circuit ball mills. Noted that the main task of modeling the grinding process is predicting the granulometric composition of the finished product taking into account constructive and technological parameters used ball mill and separator. It is shown that the most complete and informative characterization of the grinding process in a ball mill is a grinding matrix taking into account the transformation of grain composition inside the mill drum. Shows how the relative mass fraction of the particles of crushed material, get to corresponding fraction. Noted, that the actual task of reconstruction of the matrix of grinding on the experimental data obtained in the real operating installations. On the basis of experimental data obtained on industrial installations, using matrix method to determine the kinetics of the grinding process in closed circuit ball mills. The calculation method of the conversion of the grain composition of the crushed material along the mill drum developed. Taking into account the proposed approach can be optimized processing methods to improve the manufacturing process of Portland cement clinker.

2. RW Meyer Sugar Mill: 18761899. Threeroll sugar mill, oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. RW Meyer Sugar Mill: 1876-1899. Three-roll sugar mill, one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: Top roll and one bottom roll, mill housing or cheeks, and spur pinion gears. The broken projection on the mill beside the bottom roll indicates the location of the cane tray. The cane juice crushed from the cane flowed into the juice tray below the bottom rolls. It then flowed into a wooden gutter and through a short tunnel in the mill's masonry enclosure and on to the boiling house for further processing. The opening at the base of the masency wall (In the photograph) is where the gutter ran from the mill to the boiling house. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

31. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill: oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill: one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: View down at the mill from top of the mill's circular masonry enclosure. Mill animals circling above the mill, on top of the enclosure, dragged booms radiating from the drive shaft to power the mill. The drive-shaft is no longer in its upright positon but is lying next to the mill in the foreground. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Media milling process optimization for manufacture of drug nanoparticles using design of experiments (DOE).

PubMed

Nekkanti, Vijaykumar; Marwah, Ashwani; Pillai, Raviraj

2015-01-01

Design of experiments (DOE), a component of Quality by Design (QbD), is systematic and simultaneous evaluation of process variables to develop a product with predetermined quality attributes. This article presents a case study to understand the effects of process variables in a bead milling process used for manufacture of drug nanoparticles. Experiments were designed and results were computed according to a 3-factor, 3-level face-centered central composite design (CCD). The factors investigated were motor speed, pump speed and bead volume. Responses analyzed for evaluating these effects and interactions were milling time, particle size and process yield. Process validation batches were executed using the optimum process conditions obtained from software Design-Expert® to evaluate both the repeatability and reproducibility of bead milling technique. Milling time was optimized to <5 h to obtain the desired particle size (d90 < 400 nm). The desirability function used to optimize the response variables and observed responses were in agreement with experimental values. These results demonstrated the reliability of selected model for manufacture of drug nanoparticles with predictable quality attributes. The optimization of bead milling process variables by applying DOE resulted in considerable decrease in milling time to achieve the desired particle size. The study indicates the applicability of DOE approach to optimize critical process parameters in the manufacture of drug nanoparticles.

The use of semipermeable membrane devices (SPMDs) to concentrate inducers of fish hepatic mixed function oxygenase (MFO): Chapter 12

USGS Publications Warehouse

Parrott, Joanne L.; Tillitt, Donald E.

1997-01-01

Semipermeable membrane devices (SPMDs) are sampling and concentrating devices comprised of a thin polyethylene membrane containing a small quantity of triolein. They have previously been used to sample air, water and sediments and have concentrated fish tainting compounds from pulp mill effluents. The ability to induce mixed function oxygenases (MFOs) is a property of a variety of organic effluents, but the compound(s) responsible for induction have not been identified. We wanted to see if SPMDs would accumulate the MFO-inducing chemical(s) from pulp mill effluents and oil refinery effluents. Dialysates of effluent-exposed SPMDs induced ethoxyresorufin-O-deethylase (EROD) activity in a fish (Poeciliopsis lucida) hepatoma cell line, PLHC-1. In pulp mill effluents and oil sands mining and refining wastewaters, potencies varied greatly, from a few to thousands of pg TCDD-EQ/g SPMD. Low levels of inducers were seen in four pulp mills on the Athabasca R., and higher levels at one New Brunswick bleached sulphite and two Ontario bleached kraft pulp mills. The highest levels of MFO inducers were in SPMDs deployed for 14 days in wastewater from an oil sands upgrading facility, as well as SPMDs deployed at two sites on Athabasca River tributaries in the oil sands area. This suggests that natural erosion and weathering, as well as industrial processing of the oil sands, can release potent MFO inducers. Background (reference) induction by SPMD extracts ranged from non-detectable (<1) to 20 pg TCDD-EQ/g SPMD. Reactive clean-up of one of the bleached kraft mill effluent-exposed SPMD extracts on a sulfuric acid/silica gel column resulted in loss of the inducer(s), which suggested a polyaromatic hydrocarbon-type of inducing chemical(s), rather than a dioxin or furan inducer. SPMD deployments proved useful in the detection of inducers within the pulp mill process streams as extracts of SPMDs exposed to untreated bleached sulphite effluent were ten to twenty times as potent as those from secondary-treated effluent. Little is known about the nature and identity of the MFO inducers from pulp mill and refinery effluents, but the use of SPMDs as concentrators of MFO-inducing substances appears a promising avenue for future research.

Rolling Mill Hill, Nashville, TN

EPA Pesticide Factsheets

Rolling Mill Hill was the home to Nashville General Hospital from 1890 to the 1990s and encompassed several buildings and structures. These existing buildings of historical significance were re-used in the form of apartments. The original Trolley Barns on the site are now artists’ lofts and are home to several companies and non-profit offices. Nance Place, which entails additional buildings built on-site, is a Tax Credit Workforce Housing Development and is Platinum LEED certified.

32. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill, oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill, one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: End of mill into which cane was fed between top and bottom roll. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Analysis of biological factors for determination of air pollution tolerance index of selected plants in Yamuna Nagar, India.

PubMed

Sharma, Manju; Panwar, Neeraj; Arora, Pooja; Luhach, Jyoti; Chaudhry, Smita

2013-05-01

Air pollution tolerance index (APTI) calculated for various plant species growing in vicinity of three different industrial areas (Paper mill, Sugar mill, Thermal Power Plant) and Yamuna River belt of Yamuna Nagar. Studies were carried out to determine the physiological response of ten plant species. The leaf samples collected from these plant species were used to determine their plant APTI by calculating the ascorbic acid, total chlorophyll, pH, and relative water content for all selected sites. Highest pH, relative water content, ascorbic acid and total chlorophyll was observed in Castor (9.86), Parthenium (96.99%), Ficus benghalensis (14.90 mg g(-1)) and Amaranthus (7.08 mg g(-1)) at Yamuna river, Thermal power plant, Yamuna river and paper mill respectively. It was concluded that out of ten species studied only one species (Ficus benghalensis) showed moderately tolerant response in all selected sites, while other species showed sensitive response. According to observed APTI values, Ficus benghalensis showed the highest value (21.65) at sugar mill followed by thermal power plant (19.38), Paper mill (17.65) and Yamuna River (17.61). The lowest APTI values were reported in Oxalis corniculata (6.42) at Yamuna River belt followed by Malvestrum at sugar mill (7.71).

Assessment of land suitability for olive mill wastewater disposal site selection by integrating fuzzy logic, AHP, and WLC in a GIS.

PubMed

Aydi, Abdelwaheb; Abichou, Tarek; Nasr, Imen Hamdi; Louati, Mourad; Zairi, Moncef

2016-01-01

This paper presents a geographic information system-based multi-criteria site selection tool of an olive mill wastewater (OMW) disposal site in Sidi Bouzid Region, Tunisia. The multi-criteria decision framework integrates ten constraints and six factors that relate to environmental and economic concerns, and builds a hierarchy model for OMW disposal site suitability. The methodology is used for preliminary assessment of the most suitable OMW disposal sites by combining fuzzy set theory and analytic hierarchy process (AHP). The fuzzy set theory is used to standardize factors using different fuzzy membership functions while the AHP is used to establish the relative importance of the criteria. The AHP makes pairwise comparisons of relative importance between hierarchy elements grouped by both environmental and economic decision criteria. The OMW disposal site suitability is achieved by applying a weighted linear combination that uses a comparison matrix to aggregate different importance scenarios associated with environmental and economic objectives. Three different scenarios generated by different weights applied to the two objectives. The scenario (a) assigns a weight of 0.75 to the environmental and 0.25 to the economic objective, scenario (b) has equal weights, and scenario (c) features weights of 0.25 and 0.75 for environmental and economic objectives, respectively. The results from this study assign the least suitable OMW disposal site of 2.5 % when environmental and economic objectives are rated equally, while a more suitable OMW disposal site of 1.0 % is generated when the economic objective is rated higher.

Process water reduction in a wire milling operation. 1989 summer intern report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alberg, J.

1989-12-31

Johnson Filtration Systems is a company located in New Brighton, Minnesota which employs 256 people. The focus of the project was to reduce the water usage of the wire milling operation. Water in the milling process is used to clean the wire and cool the mill components. Total annual water usage for this operation is six million gallons. The milling process changes the cross sectional shape of the wire by using flattening hammers and rollers. A synthetic coolant is used to enhance this process and remove heat. The coolant is removed from the wire as it is pulled through amore » squeegee, washed it with water and dried with an air knife.« less

2013 Annual Site Inspection and Monitoring Report for Uranium Mill Tailings Radiation Control Act Title II Disposal Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This report, in fulfillment of a license requirement, presents the results of long-term surveillance and maintenance activities conducted by the U.S. Department of Energy (DOE) Office of Legacy Management in 2013 at six uranium mill tailings disposal sites reclaimed under Title II of the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978. These activities verified that the UMTRCA Title II disposal sites remain in compliance with license requirements. DOE manages six UMTRCA Title II disposal sites under a general license granted by the U.S. Nuclear Regulatory Commission (NRC) established at Title 10 Code of Federal Regulations Part 40.28. Reclamationmore » and site transition activities continue at other sites, and DOE ultimately expects to manage approximately 27 Title II disposal sites. Long-term surveillance and maintenance activities and services for these disposal sites include inspecting and maintaining the sites; monitoring environmental media and institutional controls; conducting any necessary corrective action; and performing administrative, records, stakeholder services, and other regulatory functions. Annual site inspections and monitoring are conducted in accordance with site-specific long-term surveillance plans (LTSPs) and procedures established by DOE to comply with license requirements. Each site inspection is performed to verify the integrity of visible features at the site; to identify changes or new conditions that may affect the long-term performance of the site; and to determine the need, if any, for maintenance, follow-up inspections, or corrective action. LTSPs and site compliance reports are available online at http://www.lm.doe.gov« less

Purification of Tronoh Silica Sand via preliminary process of mechanical milling

NASA Astrophysics Data System (ADS)

H, Nazratulhuda; M, Othman

2016-02-01

The purification of Tronoh silica sand is an important step in expanding technical applications of this silica sand. However no research on purifying of Tronoh silica sand has been reported. This study is focused on ball milling technique as a preliminary technique for Tronoh silica sand purification. The objectives are to study the effect of ball milling to the purification of the silica sand and to analyze its characteristics after the ball milling process. The samples before and after milling process were analyzed by using XRF, XRD, SEM and TEM. Results showed that the purity of SiO2 was increased, the size of the particles has been reduced and the surface area has increased. The crystalline phases for the silica before and after 4 hour milling time were remained constant.

Effects of grazing on leaf area index, fractional cover and evapotranspiration by a desert phreatophyte community at a former uranium mill site on the Colorado Plateau

USGS Publications Warehouse

Bresloff, Cynthia J.; Nguyen, Uyen; Glenn, Edward P.; Waugh, Jody; Nagler, Pamela L.

2013-01-01

This study employed ground and remote sensing methods to monitor the effects of grazing on leaf area index (LAI), fractional cover (fc) and evapotranspiration (ET) of a desert phreatophyte community over an 11 year period at a former uranium mill site on the Colorado Plateau, U.S. Nitrate, ammonium and sulfate are migrating away from the mill site in a shallow alluvial aquifer. The phreatophyte community, consisting of Atriplex canescens (ATCA) and Sarcobatus vermiculatus (SAVE) shrubs, intercepts groundwater and could potentially slow the movement of the contaminant plume through evapotranspiration (ET). However, the site has been heavily grazed by livestock, reducing plant cover and LAI. We used livestock exclosures and revegetation plots to determine the effects of grazing on LAI, fc and ET, then projected the findings over the whole site using multi-platform remote sensing methods. We show that ET is approximately equal to annual precipitation at the site, but when ATCA and SAVE are protected from grazing they can develop high fc and LAI values, and ET can exceed annual precipitation, with the excess coming from groundwater discharge. Therefore, control of grazing could be an effective method to slow migration of contaminants at this and similar sites in the western U.S.

Processing of palm oil mill wastes based on zero waste technology

NASA Astrophysics Data System (ADS)

Irvan

2018-02-01

Indonesia is currently the main producer of palm oil in the world with a total production reached 33.5 million tons per year. In the processing of fresh fruit bunches (FFB) besides producing palm oil and kernel oil, palm oil mills also produce liquid and solid wastes. The increase of palm oil production will be followed by an increase in the production of waste generated. It will give rise to major environmental issues especially the discharge of liquid waste to the rivers, the emission of methane from digestion pond and the incineration of empty fruit bunches (EFB). This paper describes a zero waste technology in processing palm oil mill waste after the milling process. The technology involves fermentation of palm oil mill effluent (POME) to biogas by using continuous stirred tank reactor (CSTR) in the presence of thermophilic microbes, producing activated liquid organic fertilizer (ALOF) from discharge of treated waste effluent from biogas digester, composting EFB by spraying ALOF on the EFB in the composter, and producing pellet or biochar from EFB by pyrolysis process. This concept can be considered as a promising technology for palm oil mills with the main objective of eliminating the effluent from their mills.

Determination of Specific Forces and Tool Deflections in Micro-milling of Ti-6Al-4V alloy using Finite Element Simulations and Analysis

NASA Astrophysics Data System (ADS)

Farina, Simone; Thepsonti, Thanongsak; Ceretti, Elisabetta; Özel, Tugrul

2011-05-01

Titanium alloys offer superb properties in strength, corrosion resistance and biocompatibility and are commonly utilized in medical devices and implants. Micro-end milling process is a direct and rapid fabrication method for manufacturing medical devices and implants in titanium alloys. Process performance and quality depend upon an understanding of the relationship between cutting parameters and forces and resultant tool deflections to avoid tool breakage. For this purpose, FE simulations of chip formation during micro-end milling of Ti-6Al-4V alloy with an ultra-fine grain solid carbide two-flute micro-end mill are investigated using DEFORM software. At first, specific forces in tangential and radial directions of cutting during micro-end milling for varying feed advance and rotational speeds have been determined using designed FE simulations for chip formation process. Later, these forces are applied to the micro-end mill geometry along the axial depth of cut in 3D analysis of ABAQUS. Consequently, 3D distributions for tool deflections & von Misses stress are determined. These analyses will yield in establishing integrated multi-physics process models for high performance micro-end milling and a leap-forward to process improvements.

U.S. Geological Survey research in radioactive waste disposal - Fiscal years 1983, 1984, and 1985

USGS Publications Warehouse

Dinwiddie, G.A.; Trask, N.J.

1986-01-01

The report summarizes progress on geologic and hydrologic research related to the disposal of radioactive wastes. The research is described according to whether it is related most directly to: (1) high-level and transuranic wastes, (2) low-level wastes, or (3) uranium mill tailings. Included is research applicable to the identification and geohydrologic characterization of waste-disposal sites, to investigations of specific sites where wastes have been stored, and to studies of regions or environments where waste-disposal sites might be located. A significant part of the activity is concerned with techniques and methods for characterizing disposal sites and studies of geologic and hydrologic processes related to the transport and (or) retention of waste radionuclides.

Alternative Fuels Data Center: Ethanol Production

Science.gov Websites

States is produced from starch-based crops by dry- or wet-mill processing. Nearly 90% of ethanol plants are dry mills due to lower capital costs. Dry-milling is a process that grinds corn into flour and

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Durango, Colorado: Attachment 4, Water resources protection strategy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-12-01

To achieve compliance with the proposed US Environmental Protection Agency (EPA) groundwater protection standards (Subpart A of 40 CFR 192), the US Department of Energy (DOE) proposes to meet background concentrations or the EPA maximum concentration limits (MCLS) for hazardous constituents in groundwater in the uppermost aquifer (Cliff House/Menefee aquifer) at the point of compliance (POC) at the Uranium Mill Tailings Remedial Action (UMTRA) Project disposal site in Bodo Canyon near Durango, Colorado (DOE, 1989). Details of hydrologic site characterization at the disposal site are provided in Attachment 3, Groundwater Hydrology Report. The principal features of the water resources protectionmore » strategy for the Bodo Canyon disposal site are presented in this document.« less

Near-neighbor mixing and bond dilation in mechanically alloyed Cu-Fe

NASA Astrophysics Data System (ADS)

Harris, V. G.; Kemner, K. M.; Das, B. N.; Koon, N. C.; Ehrlich, A. E.; Kirkland, J. P.; Woicik, J. C.; Crespo, P.; Hernando, A.; Garcia Escorial, A.

1996-09-01

Extended x-ray-absorption fine-structure (EXAFS) measurements were used to obtain element-specific, structural, and chemical information of the local environments around Cu and Fe atoms in high-energy ball-milled CuxFe1-x samples (x=0.50 and 0.70). Analysis of the EXAFS data shows both Fe and Cu atoms reside in face-centered-cubic sites where the first coordination sphere consists of a mixture of Fe and Cu atoms in a ratio which reflects the as-prepared stoichiometry. The measured bond distances indicate a dilation in the bonds between unlike neighbors which accounts for the lattice expansion measured by x-ray diffraction. These results indicate that metastable alloys having a positive heat of mixing can be prepared via the high-energy ball-milling process.

Impacts of river management on low energy rivers in Normandy (France) over 3000 years, first results of a geomorphological and geoarchaeological approach.

NASA Astrophysics Data System (ADS)

Beauchamp, Axel; Lespez, Laurent; Le Gaillard, Ludovic; Bernard, Vincent; Delahaye, Daniel

2014-05-01

The European Water Framework Directive (WFD), issued in 2000 has the objective of improving the quality of water and aquatic environments. In France, the application of this law requires the dismantling and razing of structures built across waterways (mill valve, mill dam…) which no longer have any use today. The first archaeological results in Normandy show evidence of river management since the Iron Age (800 BC.). They also show that during the last 4000 years, floodplains have been affected by a significant vertical aggradation resulting from soil erosion in the catchment related to the development of agro- pastoral activities. However, these results say nothing about consequences of the proliferation of mill dams for hydrosedimentary flow for low energy rivers and their role in the development of sedimentary stocks in valley beds. The aim of this work is to measure the impact of the implementation of major hydraulic structures (mill inlet, mill dam, millrace, mill valve, drainage ditches...) on the rivers functioning in the past millennia to (1) propose a long term modeling Human/Ecosystem interaction for Lower-Normandy river systems and (2) to anticipate the geomorphological consequences related to dam-removal policy. This research is based on study sites located in the valley bed, most of them have been investigated by archaeologists and have revealed old hydraulic structures. Today, five sites have been identified in varied archaeological and hydromorphological contexts. Trenching was carried out upstream and downstream of hydraulic structures to uncover the Holocene sedimentary infilling of the valley floor. First results from the antique and medieval sites Montaigu-la-Brisette (Manche, FRANCE ) and Colomby (Manche, FRANCE ) show the influence of river management on the evolution of sedimentation in valley bed.

Psychosocial and health impacts of uranium mining and milling on Navajo lands.

PubMed

Dawson, Susan E; Madsen, Gary E

2011-11-01

The uranium industry in the American Southwest has had profoundly negative impacts on American Indian communities. Navajo workers experienced significant health problems, including lung cancer and nonmalignant respiratory diseases, and psychosocial problems, such as depression and anxiety. There were four uranium processing mills and approximately 1,200 uranium mines on the Navajo Nation's over 27,000 square miles. In this paper, a chronology is presented of how uranium mining and milling impacted the lives of Navajo workers and their families. Local community leaders organized meetings across the reservation to inform workers and their families about the relationship between worker exposures and possible health problems. A reservation-wide effort resulted in activists working with political leaders and attorneys to write radiation compensation legislation, which was passed in 1990 as the Radiation Exposure Compensation Act (RECA) and included underground uranium miners, atomic downwinders, and nuclear test-site workers. Later efforts resulted in the inclusion of surface miners, ore truck haulers, and millworkers in the RECA Amendments of 2000. On the Navajo Nation, the Office of Navajo Uranium Workers was created to assist workers and their families to apply for RECA funds. Present issues concerning the Navajo and other uranium-impacted groups include those who worked in mining and milling after 1971 and are excluded from RECA. Perceptions about uranium health impacts have contributed recently to the Navajo people rejecting a resumption of uranium mining and milling on Navajo lands.

Nouvelle methode d'integration energetique pour la retro-installation des procedes industriels et la transformation des usines papetieres

NASA Astrophysics Data System (ADS)

Bonhivers, Jean-Christophe

The increase in production of goods over the last decades has led to the need for improving the management of natural resources management and the efficiency of processes. As a consequence, heat integration methods for industry have been developed. These have been successful for the design of new plants: the integration principles are largely employed, and energy intensity has dramatically decreased in many processes. Although progress has also been achieved in integration methods for retrofit, these methods still need further conceptual development. Furthermore, methodological difficulties increase when trying to retrofit heat exchange networks that are closely interrelated to water networks, such as the case of pulp and paper mills. The pulp and paper industry seeks to increase its profitability by reducing production costs and optimizing supply chains. Recent process developments in forestry biorefining give this industry the opportunity for diversification into bio-products, increasing potential profit margins, and at the same time modernizing its energy systems. Identification of energy strategies for a mill in a changing environment, including the possibility of adding a biorefinery process on the industrial site, requires better integration methods for retrofit situations. The objective of this thesis is to develop an energy integration method for the retrofit of industrial systems and the transformation of pulp and paper mills, ant to demonstrate the method in case studies. Energy is conserved and degraded in a process. Heat can be converted into electricity, stored as chemical energy, or rejected to the environment. A systematic analysis of successive degradations of energy between the hot utilities until the environment, through process operations and existing heat exchangers, is essential in order to reduce the heat consumption. In this thesis, the "Bridge Method" for energy integration by heat exchanger network retrofit has been developed. This method is the first that considers the analysis of these degradations. The fundamental mechanism to reduce the heat consumption in an existing network has been made explicit; it is the basis of the developed method. The Bridge Method includes the definition of "a bridge", which is a set of modifications leading to heat reduction in a heat exchanger network. It is proven that, for a given set of streams, only bridges can lead to heat savings. The Bridge Method also includes (1) a global procedure for heat exchanger network retrofit, (2) a procedure to enumerate systematically the bridges, (3) "a network table" to easily evaluate them, and (4) an "energy transfer diagram" showing the effect of the two first principles of thermodynamics of energy conservation and degradation in industrial processes in order to identify energy savings opportunities. The Bridge Method can be used for the analysis of networks including several types of heat transfer, and site-wide analysis. The Bridge Method has been applied in case studies for retrofitting networks composed of indirect-contact heat exchangers, including the network of a kraft pulp mill, and also networks of direct-contact heat exchangers, including the hot water production system of a pulp mill. The method has finally been applied for the evaluation of a biorefinery process, alone or hosted in a kraft pulp mill. Results show that the use of the method significantly reduces the search space and leads to identification of the relevant solutions. The necessity of a bridge to reduce the inputs and outputs of a process is a consequence of the two first thermodynamics principles of energy conservation and increase in entropy. The concept of bridge alone can also be used as a tool for process analysis, and in numerical optimization-based approaches for energy integration.

30. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill: oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

30. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill: one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1885-1870. View: Masonry-lined passage-way leading to the mill at the center of its circular masonry enclosure. The passageway permitted cane to be carried to the mill and cane trash (bagasse) to be carried away. Bridges over the passageways, no longer in place, permitted the mill animals to circle and power the mill from above. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Processing study of high temperature superconducting Y-Ba-Cu-O ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Safari, A.; Wachtman, J.B. Jr.; Ward, C.

Processing of the YBa{sub 2}Cu{sub 3}O{sub 6+x} superconducting phase by employing different precursor powder preparation techniques (ball milling, attrition milling) and samples formed by different sintering conditions are discussed. The superconducting phase has been identified by powder x-ray diffraction. The effect of different powder processing and pressing conditions on the structure, density, resistivity and a.c. magnetic susceptibility were studied. Though there is no variation in T{sub c} for all the samples, attrition milled samples show a much lower resistance and less temperature dependence compared to ball milled samples above the superconducting transition temperature up to room temperature. Ball milled samplesmore » were loosely packed with more voids compared to attrition milled samples which are more densely packed with a needle-like structure.« less

Long-term surveillance plan for the Bodo Canyon Disposal Site, Durango, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-03-01

This long-term surveillance plan (LTSP) for the Durango, Colorado, Uranium Mill Tailings Remedial Action (UMTRA) Project disposal site describes the surveillance activities for the Durango (Bodo Canyon) disposal site, which will be referred to as the disposal site throughout this document. The US Department of Energy (DOE) will carry out these activities to ensure that the disposal site continues to function as designed. This LTSP was prepared as a requirement for acceptance under the US Nuclear Regulatory Commission (NRC) general license for custody and long-term care of residual radioactive materials (RRM). RRMs include tailings and other uranium ore processing wastesmore » still at the site, which the DOE determines to be radioactive. This LTSP is based on the DOE`s Guidance for Implementing the UMTRA Project Long-term Surveillance Program (DOE, 1992).« less

Post Audit of a Field Scale Reactive Transport Model of Uranium at a Former Mill Site

NASA Astrophysics Data System (ADS)

Curtis, G. P.

2015-12-01

Reactive transport of hexavalent uranium (U(VI)) in a shallow alluvial aquifer at a former uranium mill tailings site near Naturita CO has been monitored for nearly 30 years by the US Department of Energy and the US Geological Survey. Groundwater at the site has high concentrations of chloride, alkalinity and U(VI) as a owing to ore processing at the site from 1941 to 1974. We previously calibrated a multicomponent reactive transport model to data collected at the site from 1986 to 2001. A two dimensional nonreactive transport model used a uniform hydraulic conductivity which was estimated from observed chloride concentrations and tritium helium age dates. A reactive transport model for the 2km long site was developed by including an equilibrium U(VI) surface complexation model calibrated to laboratory data and calcite equilibrium. The calibrated model reproduced both nonreactive tracers as well as the observed U(VI), pH and alkalinity. Forward simulations for the period 2002-2015 conducted with the calibrated model predict significantly faster natural attenuation of U(VI) concentrations than has been observed by the persistent high U(VI) concentrations at the site. Alternative modeling approaches are being evaluating evaluated using recent data to determine if the persistence can be explained by multirate mass transfer models developed from experimental observations at the column scale(~0.2m), the laboratory tank scale (~2m), the field tracer test scale (~1-4m) or geophysical observation scale (~1-5m). Results of this comparison should provide insight into the persistence of U(VI) plumes and improved management options.

Putney Basketville Site Biomass CHP Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunsberger, Randolph; Mosey, Gail

2013-10-01

The U.S. Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response Center for Program Analysis developed the RE-Powering America's Land initiative to reuse contaminated sites for renewable energy generation when aligned with the community's vision for the site. The Putney, Vermont, Basketville site, formerly the location of a basket-making facility and a paper mill andwoolen mill, was selected for a feasibility study under the program. Biomass was chosen as the renewable energy resource based on abundant woody-biomass resources available in the area. Biomass combined heat and power (CHP) was selected as the technology due to nearby loads, includingmore » Putney Paper and Landmark College.« less

Environmental assessment of remedial action at the Gunnison Uranium Mill Tailings Site near Gunnison, Colorado. Final

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-02-01

The presence of contaminated uranium mill tailings adjacent to the city of Gunnison has been a local concern for many years. The following issues were identified during public meetings that were held by the DOE prior to distribution of an earlier version of this EA. Many of these issues will require mitigation. Groundwater contamination; in December 1989, a herd of 105 antelope were introduced in an area that includes the Landfill disposal site. There is concern that remedial action-related traffic in the area would result in antelope mortality. The proposed Tenderfoot Mountain haul road may restrict antelope access to theirmore » water supply; a second wildlife issue concerns the potential reduction in sage grouse use of breeding grounds (leks) and nesting habitat; the proposed Tenderfoot Mountain haul road would cross areas designated as wetlands by US Army Corps of Engineers (COE); the proposed disposal site is currently used for grazing by cattle six weeks a year in the spring. Additional concerns were stated in comments on a previous version of this EA. The proposed action is to consolidate and remove all contaminated materials associated with the Gunnison processing site to the Landfill disposal site six air miles east of Gunnison. All structures on the site (e.g., water tower, office buildings) were demolished in 1991. The debris is being stored on the site until it can be incorporated into the disposal cell at the disposal site. All contaminated materials would be trucked to the Landfill disposal site on a to-be-constructed haul road that crosses BLM-administered land.« less

Nuclear facility decommissioning and site remedial actions: A selected bibliography, Volume 13: Part 1, Main text

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goins, L.F.; Webb, J.R.; Cravens, C.D.

1992-09-01

This publication contains 1035 abstracted references on environmental restoration, nuclear facility decommissioning, uranium mill tailings management, and site remedial actions. These citations constitute the thirteenth in a series of reports prepared annually for the US Department of Energy (DOE) Environmental Restoration programs. Citations to foreign and domestic literature of all types. There are 13 major sections of the publication, including: (1) DOE Decontamination and Decommissioning Program; (2) Nuclear Facilities Decommissioning; (3) DOE Formerly Utilized Sites Remedial Action Program; (4) DOE Uranium Mill Tailings Remedial Action Project; (5) Uranium Mill Tailings Management; (6) DOE Environmental Restoration Program; (7) DOE Site-Specific Remedialmore » Actions; (8) Contaminated Site Restoration; (9) Remediation of Contaminated Soil and Groundwater; (10) Environmental Data Measurements, Management, and Evaluation; (11) Remedial Action Assessment and Decision-Making; (12) Technology Development and Evaluation; and (13) Environmental and Waste Management Issues. Bibliographic references are arranged in nine subject categories by geographic location and then alphabetically by first author, corporate affiliation, or publication title. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, subject category, and key word.« less

91. Photocopied August 1978 by the Harry S. Truman Library, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

91. Photocopied August 1978 by the Harry S. Truman Library, Independence, Missouri, from the original belonging to the Watkins Mill Historic Site. JOHN WATKINS, SECOND ELDEST SON AND EVENTUAL PARTNER WITH WALTHUS L. WATKINS. - Watkins Mill, County Highway MM, Lawson, Ray County, MO

1. VIEW, LOOKING FROM THE EAST, OF THE GOLD KNOLL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW, LOOKING FROM THE EAST, OF THE GOLD KNOLL SITE. MILL FOUNDATIONS ARE AT CENTER, WITH REMAINS OF THE TRESTLE ABOVE. WASTE DUMP FROM THE SHAFT IS AT LEFT - Gold Knoll Mill, Southern Edge of Salt Spring Valley, Copperopolis, Calaveras County, CA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goins, L.F.; Webb, J.R.; Cravens, C.D.

This publication contains 1035 abstracted references on environmental restoration, nuclear facility decommissioning, uranium mill tailings management, and site remedial actions. These citations constitute the thirteenth in a series of reports prepared annually for the US Department of Energy (DOE) Environmental Restoration programs. Citations to foreign and domestic literature of all types. There are 13 major sections of the publication, including: (1) DOE Decontamination and Decommissioning Program; (2) Nuclear Facilities Decommissioning; (3) DOE Formerly Utilized Sites Remedial Action Program; (4) DOE Uranium Mill Tailings Remedial Action Project; (5) Uranium Mill Tailings Management; (6) DOE Environmental Restoration Program; (7) DOE Site-Specific Remedialmore » Actions; (8) Contaminated Site Restoration; (9) Remediation of Contaminated Soil and Groundwater; (10) Environmental Data Measurements, Management, and Evaluation; (11) Remedial Action Assessment and Decision-Making; (12) Technology Development and Evaluation; and (13) Environmental and Waste Management Issues. Bibliographic references are arranged in nine subject categories by geographic location and then alphabetically by first author, corporate affiliation, or publication title. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, subject category, and key word.« less

Development of an electromechanical principle for wet and dry milling

NASA Astrophysics Data System (ADS)

Halbedel, Bernd; Kazak, Oleg

2018-05-01

The paper presents a novel electromechanical principle for wet and dry milling of different materials, in which the milling beads are moved under a time- and local-variable magnetic field. A possibility to optimize the milling process in such a milling machine by simulation of the vector gradient distribution of the electromagnetic field in the process room is presented. The mathematical model and simulation methods based on standard software packages are worked out. The results of numerical simulations and experimental measurements of the electromagnetic field in the working chamber of a developed and manufactured laboratory plant correlate well with each other. Using the obtained operating parameters, dry milling experiments with crushed cement clinker and wet milling experiments of organic agents in the laboratory plant are performed and the results are discussed here.

The Tool Life of Ball Nose end Mill Depending on the Different Types of Ramping

NASA Astrophysics Data System (ADS)

Vopát, Tomáš; Peterka, Jozef; Kováč, Martin

2014-12-01

The article deals with the cutting tool wear measurement process and tool life of ball nose end mill depending on upward ramping and downward ramping. The aim was to determine and compare the wear (tool life) of ball nose end mill for different types of copy milling operations, as well as to specify particular steps of the measurement process. In addition, we examined and observed cutter contact areas of ball nose end mill with machined material. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, cutting speed, feed rate, axial depth of cut and radial depth of cut were not changed. The cutting tool wear was measured on Zoller Genius 3s universal measuring machine. The results show different tool life of ball nose end mills depending on the copy milling strategy.

Microstructure and magnetic properties of MFe{sub 2}O{sub 4} (M = Co, Ni, and Mn) ferrite nanocrystals prepared using colloid mill and hydrothermal method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Wei, E-mail: wangwei@mail.buct.edu.cn; Ding, Zui; Zhao, Xiruo

2015-05-07

Three kinds of spinel ferrite nanocrystals, MFe{sub 2}O{sub 4} (M = Co, Ni, and Mn), are synthesized using colloid mill and hydrothermal method. During the synthesis process, a rapid mixing and reduction of cations with sodium borohydride (NaBH{sub 4}) take place in a colloid mill then through a hydrothermal reaction, a slow oxidation and structural transformation of the spinel ferrite nanocrystals occur. The phase purity and crystal lattice parameters are estimated by X-ray diffraction studies. Scanning electron microscopy and transmission electron microscopy images show the morphology and particle size of the as-synthesized ferrite nanocrystals. Raman spectrum reveals active phonon modesmore » at room temperature, and a shifting of the modes implies cation redistribution in the tetrahedral and octahedral sites. Magnetic measurements show that all the obtained samples exhibit higher saturation magnetization (M{sub s}). Meanwhile, experiments demonstrate that the hydrothermal reaction time has significant effects on microstructure, morphologies, and magnetic properties of the as-synthesized ferrite nanocrystals.« less

Dioxin effects on wood duck (Aix sponsa) embryos from sites near paper mills

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beeman, D.K.; Melancon, M.J.; Fleming, W.J.

Biological and biochemical variables were studied in wood duck embryos from four dioxin-contaminated sites near paper mills in the Southeastern United States and three reference sites. Sites were selected based on a history of dioxin contamination in both sediments and fish. In addition, wood duck embryos collected downstream from an Arkansas Superfund site with demonstrated dioxin-induced reproductive impairment served as positive controls. Whole clutches of eggs were collected from the wild after fifteen days of incubation and mechanically incubated. Two embryos per clutch were sacrificed at pipping and liver monooxygenase activities (BROD, EROD and MROD) were quantified. Hatching success wasmore » determined for the remainder of the nest. Preliminary results indicate no difference in monooxygenase activities across sites even though the authors have previously demonstrated induction of monooxygenase activity in wood duck embryos in laboratory studies. In addition, there were no differences in weight at pipping, liver weight and liver weight to body weight ratios. No differences were seen in hatching success or weight at hatch nor were there any gross morphological abnormalities. This may indicate that exposure of wood ducks nesting near these pulp paper mills is below those which cause elevated monooxygenase activities and reproductive impairment.« less

A real-time web-based optimal Biomass Site Assessment Tool (BioSAT): Module 1. An economic assessment of mill residues for the southern U.S.

Treesearch

Timothy M. Young; James H. Perdue; Andy Hartsell; Robert C. Abt; Donald Hodges; Timothy G. Rials

2009-01-01

Optimal locations for biomass facilities that use mill residues are identified for 13 southern U.S. states. The Biomass Site Assessment Tool (BioSAT) model is used to identify the top 20 locations for 13 southern U.S. states. The trucking cost model of BioSAT is used with Timber Mart South 2009 price data to estimate the total cost, average cost, and marginal costs for...

Lumber Cost Minimization through Optimum Grade-Mix Selection

Treesearch

Xiaoqiu Zuo; Urs Buehlmann; R. Edward Thomas; R. Edward Thomas

2003-01-01

Rough mills process kiln-dried lumber into components for the furniture and wood products industries, Lumber is a significant portion of total rough mill costs and lumber quality can have a serious impact on mill productivity. Lower quality lumber is less expensive yet is harder to process. Higher quality lumber is more expensive yet easier to process. The problem of...

An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring.

PubMed

Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

2016-02-23

An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies.

An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring

PubMed Central

Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

2016-01-01

An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies. PMID:26907297

40 CFR 60.670 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... mineral processing plants: each crusher, grinding mill, screening operation, bucket elevator, belt... grinding mills at hot mix asphalt facilities that reduce the size of nonmetallic minerals embedded in... or grinding mills above ground; and wet material processing operations (as defined in § 60.671). (b...

Baseline risk assessment of ground water contamination at the uranium mill tailings site near Durango, Colorado. Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-09-01

For the UMTRA Project site located near Durango, Colorado (the Durango site), the Surface Project cleanup occurred from 1986 to 1991. An evaluation was made to determine whether exposure to ground water contaminated by uranium processing could affect people`s health. Exposure could occur from drinking water pumped from a hypothetical well drilled in the contaminated ground water area. In addition, environmental risks may result if plants or animals are exposed to contaminated ground water, or surface water that has mixed with contaminated ground water. This risk assessment report is the first site-specific document prepared for the UMTRA Ground Water Projectmore » at the Durango site. The results of this report and further site characterization of the Durango site will be used to determine what is necessary to protect public health and the environment, and to comply with the EPA standards.« less

1. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill: oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill: one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: Historical view, 1934, from T.T. Waterman collection, Hawaiian Sugar Planters' Association. Large rectangular piece lying in front of the mill is the top of the mill frame appearing in its proper place in 1928 views. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Fabrication of novel cryomill for synthesis of high purity metallic nanoparticles

NASA Astrophysics Data System (ADS)

Kumar, Nirmal; Biswas, Krishanu

2015-08-01

The successful preparation of free standing metal nanoparticles with high purity in bulk quantity is the pre-requisite for any potential application. This is possible by using ball milling at cryogenic temperature. However, the most of ball mills available in the market do not allow preparing high purity metal nanoparticles by this route. In addition, it is not possible to carry out in situ measurements of process parameters as well as diagnostic of the process. In the present investigation, we present a detailed study on the fabrication of a cryomill, which is capable of avoiding contaminations in the product. It also provides in situ measurements and diagnostic of the low temperature milling process. Online monitoring of the milling temperature and observation of ball motion are the important aspects in the newly designed mill. The nanoparticles prepared using this fabricated mill have been found to be free standing and also free from contaminations.

Numerical simulation study on rolling-chemical milling process of aluminum-lithium alloy skin panel

NASA Astrophysics Data System (ADS)

Huang, Z. B.; Sun, Z. G.; Sun, X. F.; Li, X. Q.

2017-09-01

Single curvature parts such as aircraft fuselage skin panels are usually manufactured by rolling-chemical milling process, which is usually faced with the problem of geometric accuracy caused by springback. In most cases, the methods of manual adjustment and multiple roll bending are used to control or eliminate the springback. However, these methods can cause the increase of product cost and cycle, and lead to material performance degradation. Therefore, it is of significance to precisely control the springback of rolling-chemical milling process. In this paper, using the method of experiment and numerical simulation on rolling-chemical milling process, the simulation model for rolling-chemical milling process of 2060-T8 aluminum-lithium alloy skin was established and testified by the comparison between numerical simulation and experiment results for the validity. Then, based on the numerical simulation model, the relative technological parameters which influence on the curvature of the skin panel were analyzed. Finally, the prediction of springback and the compensation can be realized by controlling the process parameters.

Feasibility Study of Economics and Performance of Solar Photovoltaics at the Peru Mill Industrial Park in the City of Deming, New Mexico. A Study Prepared in Partnership with the Environmental Protection Agency for the RE-Powering America's Land Initiative: Siting Renewable Energy on Potentially Contaminated Land and Mine Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiatreungwattana, K.; Geiger, J.; Healey, V.

2013-04-01

The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Peru Mill Industrial Park site in the City of Deming, New Mexico, for a feasibility study of renewable energy production. The National Renewable Energy Laboratory (NREL) provided technical assistance for this project. The purpose of this report is to assess the site for a possible photovoltaic (PV) system installation and estimate the cost, performance, and site impacts of different PV options. In addition, the report recommends financing options that could assist in the implementation of a PV system at the site.

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Durango, Colorado: Attachment 4, Water resources protection strategy. Revised final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-12-01

To achieve compliance with the proposed US Environmental Protection Agency (EPA) groundwater protection standards (Subpart A of 40 CFR 192), the US Department of Energy (DOE) proposes to meet background concentrations or the EPA maximum concentration limits (MCLS) for hazardous constituents in groundwater in the uppermost aquifer (Cliff House/Menefee aquifer) at the point of compliance (POC) at the Uranium Mill Tailings Remedial Action (UMTRA) Project disposal site in Bodo Canyon near Durango, Colorado (DOE, 1989). Details of hydrologic site characterization at the disposal site are provided in Attachment 3, Groundwater Hydrology Report. The principal features of the water resources protectionmore » strategy for the Bodo Canyon disposal site are presented in this document.« less

Feasibility Study of Economics and Performance of Geothermal Power Generation at the Lakeview Uranium Mill Site in Lakeview, Oregon. A Study Prepared in Partnership with the Environmental Protection Agency for the RE-Powering America's Land Initiative: Siting Renewable Energy on Potentially Contaminated Land and Mine Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hillesheim, M.; Mosey, G.

2013-11-01

The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Lakeview Uranium Mill site in Lakeview, Oregon, for a feasibility study of renewable energy production. The EPA contracted with the National Renewable Energy Laboratory (NREL) to provide technical assistance for the project. The purpose of this report is to describe an assessment of the site for possible development of a geothermal power generation facility and to estimate the cost, performance, and site impacts for the facility. In addition, the report recommends development pathways that could assist in the implementation of a geothermal power systemmore » at the site.« less

Effects of grazing on leaf area index, fractional cover and evapotranspiration by a desert phreatophyte community at a former uranium mill site on the Colorado Plateau.

PubMed

Bresloff, Cynthia J; Nguyen, Uyen; Glenn, Edward P; Waugh, Jody; Nagler, Pamela L

2013-01-15

This study employed ground and remote sensing methods to monitor the effects of grazing on leaf area index (LAI), fractional cover (f(c)) and evapotranspiration (ET) of a desert phreatophyte community over an 11 year period at a former uranium mill site on the Colorado Plateau, U.S. Nitrate, ammonium and sulfate are migrating away from the mill site in a shallow alluvial aquifer. The phreatophyte community, consisting of Atriplex canescens (ATCA) and Sarcobatus vermiculatus (SAVE) shrubs, intercepts groundwater and could potentially slow the movement of the contaminant plume through evapotranspiration (ET). However, the site has been heavily grazed by livestock, reducing plant cover and LAI. We used livestock exclosures and revegetation plots to determine the effects of grazing on LAI, f(c) and ET, then projected the findings over the whole site using multi-platform remote sensing methods. We show that ET is approximately equal to annual precipitation at the site, but when ATCA and SAVE are protected from grazing they can develop high f(c) and LAI values, and ET can exceed annual precipitation, with the excess coming from groundwater discharge. Therefore, control of grazing could be an effective method to slow migration of contaminants at this and similar sites in the western U.S. Copyright © 2012 Elsevier Ltd. All rights reserved.

Comparison of high pressure homogenization and stirred bead milling for the production of nano-crystalline suspensions.

PubMed

Nakach, Mostafa; Authelin, Jean-René; Perrin, Marc-Antoine; Lakkireddy, Harivardhan Reddy

2018-05-19

Currently, the two technologies primarily used for the manufacturing of nano-crystalline suspensions using top down process (i.e. wet milling) are high pressure homogenization (HPH) and stirred bead milling (SBM). These two technologies are based upon different mechanisms, i.e., cavitation forces for HPH and shear forces for stirred bead milling. In this article, the HPH and SBM technologies are compared in terms of the impact of the suspension composition the process parameters and the technological configuration on milling performances and physical quality of the suspensions produced. The data suggested that both HPH and SBM are suitable for producing nano-crystalline suspensions, although SBM appeared more efficient than HPH, since the limit of milling (d 50 ) for SBM was found to be lower than that obtained with HPH (100 nm vs 200 nm). For both these technologies, regardless of the process parameters used for milling and the scale of manufacturing, the relationship of d 90 versus d 50 could be described by a unique master curve (technology signature of milling pathway) outlining that the HPH leads to more uniform particle size distribution as compared to SBM. Copyright © 2018 Elsevier B.V. All rights reserved.

Review of samples of tailings, soils and stream sediment adjacent to and downstream from the Ruth Mine, Inyo County, California

USGS Publications Warehouse

Rytuba, James J.; Kim, Christopher S.; Goldstein, Daniel N.

2011-01-01

The Ruth Mine and mill are located in the western Mojave Desert in Inyo County, California (fig. 1). The mill processed gold-silver (Au-Ag) ores mined from the Ruth Au-Ag deposit, which is adjacent to the mill site. The Ruth Au-Ag deposit is hosted in Mesozoic intrusive rocks and is similar to other Au-Ag deposits in the western Mojave Desert that are associated with Miocene volcanic centers that formed on a basement of Mesozoic granitic rocks (Bateman, 1907; Gardner, 1954; Rytuba, 1996). The volcanic rocks consist of silicic domes and associated flows, pyroclastic rocks, and subvolcanic intrusions (fig. 2) that were emplaced into Mesozoic silicic intrusive rocks (Troxel and Morton, 1962). The Ruth Mine is on Federal land managed by the U.S. Bureau of Land Management (BLM). Tailings from the mine have been eroded and transported downstream into Homewood Canyon and then into Searles Valley (figs. 3, 4, 5, and 6). The BLM provided recreational facilities at the mine site for day-use hikers and restored and maintained the original mine buildings in collaboration with local citizen groups for use by visitors (fig. 7). The BLM requested that the U.S. Geological Survey (USGS), in collaboration with Chapman University, measure arsenic (As) and other geochemical constituents in soils and tailings at the mine site and in stream sediments downstream from the mine in Homewood Canyon and in Searles Valley (fig. 3). The request was made because initial sampling of the site by BLM staff indicated high concentrations of As in tailings and soils adjacent to the Ruth Mine. This report summarizes data obtained from field sampling of mine tailings and soils adjacent to the Ruth Mine and stream sediments downstream from the mine on June 7, 2009. Our results permit a preliminary assessment of the sources of As and associated chemical constituents that could potentially impact humans and biota.

76 FR 44535 - Testing of Bisphenol A

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-26

... Web site is an ``anonymous access'' system, which means EPA will not know your identity or contact... INFORMATION: I. General Information A. Does this action apply to me? You may be potentially affected by this.... Paper recyclers (NAICS codes 322110, 322121, 3222), e.g., pulp mills, paper (except newsprint) mills...

Biota: sediment partitioning of aluminium smelter related PAHs and pulp mill related diterpenes by intertidal clams at Kitimat, British Columbia.

PubMed

Yunker, Mark B; Lachmuth, Cara L; Cretney, Walter J; Fowler, Brian R; Dangerfield, Neil; White, Linda; Ross, Peter S

2011-09-01

The question of polycyclic aromatic hydrocarbon (PAH) bioavailability and its relationship to specific PAH sources with different PAH binding characteristics is an important one, because bioavailability drives PAH accumulation in biota and ultimately the biochemical responses to the PAH contaminants. The industrial harbour at Kitimat (British Columbia, Canada) provides an ideal location to study the bioavailability and bioaccumulation of sediment hydrocarbons to low trophic level biota. Samples of soft shell clams (Mya arenaria) and intertidal sediment collected from multiple sites over six years at various distances from an aluminium smelter and a pulp and paper mill were analysed for 106 PAHs, plant diterpenes and other aromatic fraction hydrocarbons. Interpretation using PAH source ratios and multivariate data analysis reveals six principal hydrocarbon sources: PAHs in coke, pitch and emissions from anode combustion from the aluminium smelter, vascular plant terpenes and aromatised terpenes from the pulp and paper mill, petroleum PAHs from shipping and other anthropogenic activities and PAHs from natural plant detritus. Harbour sediments predominantly contain either pitch or pyrogenic PAHs from the smelter, while clams predominantly contain plant derived PAHs and diterpenes from the adjacent pulp mill. PAHs from the smelter have low bioavailability to clams (Biota-Sediment Accumulation Factors; BSAFs <1 for pitch and coke; <10 for anode combustion, decreasing to ∼0.1 for the mass 300 and 302 PAHs), possibly due to binding to pitch or soot carbon matrices. Decreases in PAH isomer ratios between sediments and clams likely reflect a combination of variation in uptake kinetics of petroleum PAHs and compound specific metabolism, with the importance of petroleum PAHs decreasing with increasing molecular weight. Plant derived compounds exhibit little natural bioaccumulation at reference sites, but unsaturated and aromatised diterpenes released from resins by industrial pulping processes are readily accumulated by the clams (BSAFs >500). Thus while most of the smelter associated PAHs in sediments may not be bioavailable to benthic organisms, the plant terpenes (including retene, totarol, ferruginol, manool, dehydroabietane and other plant terpenes that form the chemical defence mechanism of conifers) released by pulp mills are bioavailable and possess demonstrated toxic properties. The large scale release of plant terpenes by some of the many pulp mills located in British Columbia and elsewhere represents a largely undocumented risk to aquatic biota. Copyright © 2011 Elsevier Ltd. All rights reserved.

Production of β-xylosidase from Trichoderma asperellum KIF125 and its application in efficient hydrolysis of pretreated rice straw with fungal cellulase.

PubMed

Inoue, Hiroyuki; Kitao, Chiaki; Yano, Shinichi; Sawayama, Shigeki

2016-11-01

On-site cellulase and hemicellulase production is a promising way to reduce enzyme cost in the commercialization of the lignocellulose-to-ethanol process. A hemicellulase-producing fungal strain suitable for on-site enzyme production was selected from cultures prepared using wet disc-milling rice straw (WDM-RS) and identified as Trichoderma asperellum KIF125. KIF125 hemicellulase showed uniquely high abundance of β-xylosidase in the xylanolytic enzyme system compared to other fungal hemicellulase preparations. Supplementation of Talaromyces cellulolyticus cellulase with KIF125 hemicellulase was more effective than that with the hemicellulases from other fungal sources in reducing the total enzyme loading for the improvement of xylose yield in the hydrolysis of ball-milling RS, due to its high β-xylosidase dominance. β-Xylosidase in KIF125 hemicellulase was purified and classified as a glycosyl hydrolase family 3 enzyme with relatively high specificity for xylobiose. The production of KIF125 β-xylosidase in the fermentor was estimated as 118 U/g-WDM-RS (2350 U/L culture) at 48 h. These results demonstrate that KIF125 is promising as a practical hemicellulase source to combine with on-site cellulase production using T. cellulolyticus.

Fluidized Bed Opposed Jet Mill System for Processing Inorganic Materials

NASA Astrophysics Data System (ADS)

Al-Nuzal, S. M. D.; Mohammed, M. I.

2017-08-01

A jet mill system was built aiming to give values for processing inorganic materials, to be used for different industry. The milling housing of the system is composed of; milling chamber, compressed air nozzles which deliver compressed air in the milling chamber to accelerate sample particles. The classifier wheel is composed of two concentric pieces welded together under argon and coupled to a AC Motor, 0 - 9000 rpm, 2 kW, with AC frequencies convertor. The performances of this jet mill system were tried on five cheap locally available materials, viz. white sand, glass, iron oxide, black carbon and alum. It is possible to get particle sizes of less than 1 μm with narrow distribution of particle sizes.

Annual monitoring report for the Gunnison, Colorado, wetlands mitigation plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-10-01

The US Department of Energy (DOE) administers the Uranium Mill Tailings Remedial Action (UMTRA) Project to clean up uranium mill tailings and other surface contamination at 24 abandoned uranium mill sites in 10 states. One of these abandoned mill sites is near the town of Gunnison, Colorado; surface remediation and the environmental impacts of remedial action are described in the Gunnison environmental assessment (EA) (DOE, 1992). Remedial action resulted in the elimination of 4.3 acres (ac) 1.7 hectares (ha) of wetlands and mitigation of this loss of wetlands is being accomplished through the enhance of 18.4 ac (7.5 ha) ofmore » riparian plant communities in six spring feed areas on Bureau of Land Management (BLM) land. The description of the impacted and mitigation wetlands is provided in the Mitigation and Monitoring Plan for Impacted Wetlands at the Gunnison UMTRA Project Site, Gunnison, Colorado (DOE, 1994), which is attached to the US Army corps of Engineers (USACE) Section 404 Permit. As part of the wetlands mitigation plan, the six mitigation wetlands were fenced in the fall of 1993 to exclude livestock grazing. Baseline of grazed conditions of the wetlands vegetation was determined during the summer of 1993 (DOE, 1994). A 5-year monitoring program of these six sites has been implemented to document the response of vegetation and wildlife to the exclusion of livestock. This annual monitoring report provides the results of the first year of the 5-year monitoring period.« less

Influence of in situ and ex situ ZrO2 addition on the properties of MgB2

NASA Astrophysics Data System (ADS)

Chen, S. K.; Glowacki, B. A.; MacManus-Driscoll, J. L.; Vickers, M. E.; Majoros, M.

2004-02-01

The effect of ZrO2 addition on the properties of MgB2 has been studied using in situ and ex situ processes. The in situ process was performed by introducing ZrO2 from the milling tools into MgB2 throughout the planetary ball milling, whereas the ex situ process was accomplished by mixing ZrO2 from the milling tools with MgB2 by hand grinding in a mortar. A detectable amount of ZrO2 was present in MgB2 after 4 h of milling during the in situ process and its content increased with milling time as expected. The 400 h milled powder was partially amorphized and showed the formation of a minority ZrB2 phase. For milling up to 100 h, diamagnetism of MgB2 was significantly reduced while Tc remained unchanged. Superconductivity was totally destroyed after 148 h of milling. The loss of superconductivity is attributed to the effect of disordering induced by mechanical milling. As a result of in situ ZrO2 addition, the initial Tc and crystal structure of MgB2 could not be restored upon annealing. With increasing milling time, the expansion of lattice parameters in both the a-axis and c-axis may be due to possible substitution of Mg or B by Zr. The result from the magnetic measurement shows that Jc of MgB2 is deteriorated by in situ ZrO2 addition. On the other hand, ex situ ZrO2 addition with annealing did not degrade the Tc of MgB2.

A new approach for remediation of As-contaminated soil: ball mill-based technique.

PubMed

Shin, Yeon-Jun; Park, Sang-Min; Yoo, Jong-Chan; Jeon, Chil-Sung; Lee, Seung-Woo; Baek, Kitae

2016-02-01

In this study, a physical ball mill process instead of chemical extraction using toxic chemical agents was applied to remove arsenic (As) from contaminated soil. A statistical analysis was carried out to establish the optimal conditions for ball mill processing. As a result of the statistical analysis, approximately 70% of As was removed from the soil at the following conditions: 5 min, 1.0 cm, 10 rpm, and 5% of operating time, media size, rotational velocity, and soil loading conditions, respectively. A significant amount of As remained in the grinded fine soil after ball mill processing while more than 90% of soil has the original properties to be reused or recycled. As a result, the ball mill process could remove the metals bound strongly to the surface of soil by the surface grinding, which could be applied as a pretreatment before application of chemical extraction to reduce the load.

Influencing Factors and Workpiece's Microstructure in Laser-Assisted Milling of Titanium

NASA Astrophysics Data System (ADS)

Wiedenmann, R.; Liebl, S.; Zaeh, M. F.

Today's lightweight components have to withstand increasing mechanical and thermal loads. Therefore, advanced materials substitute conventional materials like steel or aluminum alloys. Using these high-performance materials the associated costs become prohibitively high. This paper presents the newest fundamental investigations on the hybrid process 'laser-assisted milling' which is an innovative technique to process such materials. The focus is on the validation of a numerical database for a CAD/CAM process control unit which is calculated by using simulation. Prior to that, the influencing factors on a laser-assisted milling process are systematically investigated using Design of Experiments (DoE) to identify the main influencing parameters coming from the laser and the milling operation.

33. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill, oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

33. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill, one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: From above the mill showing the three 15' x 22' horizontal rolls, mill frame or cheeks, portland cement foundation, and lower part of vertical drive shaft lying next mill in foreground. The loose metal piece resting on top of the mill frame matched the indented portion of the upper frame to form a bracket and bearing for the drive shaft when it was in its proper upright position. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Use of purple durum wheat to produce naturally functional fresh and dry pasta.

PubMed

Ficco, Donatella Bianca Maria; De Simone, Vanessa; De Leonardis, Anna Maria; Giovanniello, Valentina; Del Nobile, Matteo Alessandro; Padalino, Lucia; Lecce, Lucia; Borrelli, Grazia Maria; De Vita, Pasquale

2016-08-15

In this study, the effects of different milling procedures (roller-milling vs. stone-milling) and pasta processing (fresh vs. dried spaghetti), and cooking on the antioxidant components and sensory properties of purple durum wheat were investigated. Milling and pasta processing were performed using one purple and one conventional non-pigmented durum wheat genotypes, and the end-products were compared with commercial pasta. The results show that the stone milling process preserved more compounds with high health value (total fibre and carotenoids, and in the purple genotype, also anthocyanins) compared to roller-milling. The drying process significantly (p<0.05) reduced the content of anthocyanins (21.42 μg/g vs. 46.32 μg/g) and carotenoids (3.77 μg/g vs. 4.04 μg/g) with respect to the pasteurisation process involved in fresh pasta production. The sensory properties of pasta from the purple genotype did not significantly differ from commercial wholemeal pasta, and its in vitro glycemic index was even lower. Thus, it is possible to consider this genetic material as a good ingredient for the production of functional foods from cereals naturally rich in bioactive compounds. Copyright © 2016 Elsevier Ltd. All rights reserved.

Rough Mill Improvement Guide for Managers and Supervisors

Treesearch

Philip H. Mitchell; Jan Wiedenbeck; Bobby Ammerman; Bobby Ammerman

2005-01-01

Wood products manufacturers require an efficient recovery of product from lumber to remain profitable. A company's ability to obtain the best yield in lumber cut-up operations (i.e., the rough mill) varies according to the raw material, product, processing equipment, processing environment, and knowledge and skill of the rough mill's employees. This book...

Microbiological, Geochemical and Hydrologic Processes Controlling Uranium Mobility: An Integrated Field-Scale Subsurface Research Challenge Site at Rifle, Colorado, Quality Assurance Project Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fix, N. J.

The U.S. Department of Energy (DOE) is cleaning up and/or monitoring large, dilute plumes contaminated by metals, such as uranium and chromium, whose mobility and solubility change with redox status. Field-scale experiments with acetate as the electron donor have stimulated metal-reducing bacteria to effectively remove uranium [U(VI)] from groundwater at the Uranium Mill Tailings Site in Rifle, Colorado. The Pacific Northwest National Laboratory and a multidisciplinary team of national laboratory and academic collaborators has embarked on a research proposed for the Rifle site, the object of which is to gain a comprehensive and mechanistic understanding of the microbial factors andmore » associated geochemistry controlling uranium mobility so that DOE can confidently remediate uranium plumes as well as support stewardship of uranium-contaminated sites. This Quality Assurance Project Plan provides the quality assurance requirements and processes that will be followed by the Rifle Integrated Field-Scale Subsurface Research Challenge Project.« less

The challenge of climate to man

NASA Astrophysics Data System (ADS)

Hecht, Alan D.

Around 900 A.D. a group of small villages was established in northwest Iowa by Indians of what we now call the Mill Creek culture. Around 1400 A.D., after many prosperous years, the villages were abandoned. In the summer of 1963, archeological and geological excavations of several sites of the Mill Creek culture began. While three major sites were excavated, one known as Phipps site provided the clearest historical record of civilization in the area. To reconstruct both the habits of the Mill Creek people and the environment in which they lived, scientists have studied a wide assortment of remains preserved in the strata of northwestern Iowa. Unnoticed without the aid of a microscope are the remains of pollen grains blown into the area from surrounding trees. The pollen preserved in the strata can be read as an historic log of changes in the vegetation and climate surrounding the Mill Creek area. The village was occupied about 900 A.D. on the flood plain of Mill Creek. The pollen evidence shows that during the 10th and 11th centuries, the Indians lived in a region with tall-grass prairie on the uplands and woods on the valley terraces and valley floors. This vegetation is not very different from today's if one substitutes ‘cornfield’ for ‘prairie.’ From evidence given by fossil bones found in the strata, it seems that deer and elk were abundant and were hunted by these Indians. The Indian meat diet appears to have been dominated by these animals, supplemented only occasionally by bison. Maize was the main agricultural product.

Water- and Bed-Sediment Quality of Seguchie Creek and Selected Wetlands Tributary to Mille Lacs Lake in Crow Wing County, Minnesota, October 2003 to October 2006

USGS Publications Warehouse

Fallon, James D.; Yaeger, Christine S.

2009-01-01

Mille Lacs Lake and its tributaries, located in east-central Minnesota, are important resources to the public. In addition, many wetlands and lakes that feed Mille Lacs Lake are of high resource quality and vulnerable to degradation. Construction of a new four-lane expansion of U.S. Highway 169 has been planned along the western part of the drainage area of Mille Lacs Lake in Crow Wing County. Concerns exist that the proposed highway could affect the resource quality of surface waters tributary to Mille Lacs Lake. Baseline water- and bed-sediment quality characteristics of surface waters tributary to Mille Lacs Lake were needed prior to the proposed highway construction. The U.S. Geological Survey, in cooperation with the Minnesota Department of Transportation, characterized the water- and bed-sediment quality at selected locations that the proposed route intersects from October 2003 to October 2006. Locations included Seguchie Creek upstream and downstream from the proposed route and three wetlands draining to Mille Lacs Lake. The mean streamflow of Seguchie Creek increased between the two sites: flow at the downstream streamflow-gaging station of 0.22 cubic meter per second was 5.6 percent greater than the mean streamflow at the upstream streamflow-gaging station of 0.21 cubic meter per second. Because of the large amount of storage immediately upstream from both gaging stations, increases in flow were gradual even during intense precipitation. The ranges of most constituent concentrations in water were nearly identical between the two sampling sites on Seguchie Creek. No concentrations exceeded applicable water-quality standards set by the State of Minnesota. Dissolved-oxygen concentrations at the downstream gaging station were less than the daily minimum standard of 4.0 milligrams per liter for 6 of 26 measurements. Constituent loads in Seguchie Creek were greater at the downstream site than the upstream site for all measured, including dissolved chloride (1.7 percent), ammonia plus organic nitrogen (13 percent), total phosphorus (62 percent), and suspended sediment (11 percent) during the study. All constituents had seasonal peaks in spring and fall. The large loads during the fall resulted from unusually large precipitation and streamflow patterns. This caused the two greatest streamflow peaks at both sites to occur during October (2004 and 2005). In Seguchie Creek, bed-sediment concentrations of five metals and trace elements (arsenic, cadmium, chromium, lead, and zinc) exceeded the Interim Sediment Quality Guidelines (ISQG) set by the Canadian Council of Ministers of the Environment. Bed-sediment samples from the upstream site had more exceedances of ISQGs for metals and trace elements than did samples from the downstream site (seven and two exceedances, respectively). Bed-sediment samples from the downstream site had more exceedances of ISQGs (20 exceedances) for semivolatile organic compounds than did samples from the upstream site (8 exceedances), indicating different sources for organic compounds than for metals and trace elements. Concentrations of 11 semivolatile organic compounds exceeded ISQGs: ancenaphthene, acenaphthylene, anthracene, benzo[a]anthracene, benzo[a]pyrene, chrysene, fluoranthene, fluorene, naphthalene, phenanthrene, and pyrene. In bed-sediment samples collected from three wetlands, concentrations of all six metals exceeded ISQGs: arsenic, cadmium, chromium, copper, lead, and zinc. Concentrations of three semivolatile organic compounds exceeded ISQGs: flouranthene, phenanthrene, and pyrene. Results indicate that areas appearing relatively undisturbed and of high resource value can have degraded quality from previous unknown land use.

Contamination of the human food chain by uranium mill tailings piles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holtzman, R.B.; Urnezis, P.W.; Padova, A.

A study is in progress to estimate the contamination of the human food chain by uranium, /sup 230/Th, /sup 226/Ra /sup 210/Pb, and /sup 210/Po originating from tailing piles associated with uranium ore processing mills. Rabbits, cattle, vegetables, and grass were collected on or near two uranium mill sites. For controls, similar samples were obtained from areas 20 km or more from the mining and mill operations. For the onsite rabbits the mean /sup 226/Ra concentrations in muscle, lung, and kidney of 5.5, 14, and 15 pCi/kg wet, respectively, were substantially higher than those in the respective tissues of controlmore » animals (0.4, 1.5, and 0.2 pCi/kg). The levels in liver did not differ significantly between the groups. The concentrations in bone (femur and vertebra) were about 9000 and 350 pCi/kg ash for the onsite and offsite animals, respectively. The levels of /sup 210/Pb and /sup 210/Po did not differ significantly for a given tissue between the two groups, except that the /sup 210/Pb level in the kidney was greater in the onsite group. For cattle, the concentrations in muscle, liver, and kidney do not differ greatly between those grazed near the pile and the controls. The levels of /sup 226/Ra, and possibly of /sup 210/Pb, appear to be greater in the femur of the animals near the piles. Vegetables from a residential area on a mill site contained substantially greater concentrations of /sup 226/Ra and /sup 210/Pb than those reported for standard New York City diets. Grass and cattle dung from land irrigated by water containing 60 pCi/L /sup 226/Ra from uranium mines had concentrations of /sup 226/Ra and /sup 210/Pb 50 and 8 times, respectively, those in control samples. It is estimated that doubling the normal concentrations in meat and vegetables of uranium and daughter products could increase the dose equivalent rates to the skeletons of persons consuming these foods by 30 or more mrem/yr.« less

Influence of food supply and chlorinated hydrocarbon contaminants on breeding success of bald eagles.

PubMed

Gill, Christopher E; Elliott, John E

2003-01-01

Food supply and contaminants were investigated as possible causes of low bald eagle productivity near a bleached kraft pulp and paper mill at Crofton on Vancouver Island, British Columbia. Over a seven year period, 1992-1998, average productivity of five eagle territories situated south of the pulp mill at Crofton was significantly lower (0.43 young/occupied territory) than six territories north of the mill (1.04 young/occupied territory). A reference population of 32 territories located in Barkley Sound on the west coast of Vancouver Island demonstrated intermediary mean productivity (0.75 young/occupied territory). Measures of prey biomass delivered to nests were lowest south of the mill, and correlated significantly with nesting success. On average, measures of energy delivered to nests and a parameter determined to be related to prey availability, adult nest attendance time, accounted for about 70% of variability in nest success. Contaminant concentrations, including pulp mill derived polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs), as well as dichlorodiphenyldichloroethane (DDE), polychlorinated biphenyls (PCBs), and calculated tetrachlorodibenzo-p-dioxin toxic equivalents (TEQs) were significantly greater in plasma samples of nestlings from south of the mill compared to the other two sites, but did not correlate significantly with individual nest success data. Nests south of the mill concentrate around Maple Bay, which appears to be a deposition area for contaminants transported by tides and currents from sources such as the pulp mill. Concentrations of DDE and PCBs in plasma of nestling eagles from south of the mill were less than the critical values estimated to affect production of young. For TEQs, there are no published critical values for plasma by which to compare our results. We conclude that less than adequate energy provisioning to nests, presumably related to low prey availability, was likely the main cause of poor nest success south of the mill site at Crofton. However, higher concentrations of both DDE and PCDD/F derived TEQs may have acted in concert with food stress to further reduce bald eagle productivity.

Selected resin acids in effluent and receiving waters derived from a bleached and unbleached kraft pulp and paper mill

USGS Publications Warehouse

Quinn, B.P.; Booth, M.M.; Delfino, J.J.; Holm, S.E.; Gross, T.S.

2003-01-01

Water samples were collected on three dates at 24 sites influenced by effluent from Georgia-Pacific's Palatka Pulp and Paper Mill Operation, a bleached and unbleached kraft mill near Palatka, Florida, USA. The sampling sites were located within the mill retention ponds, Rice Creek, and the St. John's River. Samples were analyzed by gas chromatography-mass spectrometry for abietic, dehydroabietic, and isopimaric acids, all of which are potentially toxic by-products of pulp production. Isopimaric acid concentrations greater than 12 mg/L were measured at the mill's effluent outfall but were less than 20 ??g/L at the end of Rice Creek. This result indicates that the waters of Rice Creek provide dilution or conditions conducive for degradation or sorption of these compounds. Large differences in resin acid concentrations were observed between sampling events. In two sampling events, the maximum observed concentrations were less than 2 mg/L for each analyte. In a third sampling event, all of the compounds were detected at concentrations greater than 10 mg/L. Data from the three sample dates showed that resin acid concentrations were below 20 ??g/L before the confluence of Rice Creek and the St. John's River in all cases.

Nuclear facility decommissioning and site remedial actions: A selected bibliography: Volume 8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owen, P.T.; Michelson, D.C.; Knox, N.P.

1987-09-01

The 553 abstracted references on nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the eighth in a series of reports. Foreign and domestic literature of all types - technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions - has been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of energy's remedial action program. Major chapters are Surplus Facilities Management Program, Nuclear Facilities Decommissioning, Formerly Utilized Sites Remedial Action Program, Facilities Contaminated with Naturally Occurring Radionuclides, Uranium Mill Tailings Remedial Action Program,more » Uranium Mill Tailings Management, Technical Measurements Center, and General Remedial Action Program Studies. Chapter sections for chapters 1, 2, 5, and 6 include Design, Planning, and Regulations; Environmental Studies and Site Surveys; Health, Safety, and Biomedical Studies; Decontamination Studies; Dismantlement and Demolition; Site Stabilization and Reclamation; Waste Disposal; Remedial Action Experience; and General Studies. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication description. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, and keywords. The appendix contains a list of frequently used acronyms and abbreviations.« less

High frequency monitoring revels new insights into baseflow DOM processing

NASA Astrophysics Data System (ADS)

Khamis, K.; Bradley, C.; Blaen, P.; Krause, S.; Hannah, D. M.

2017-12-01

Dissolved organic matter (DOM) is important for myriad biogeochemical processes in river ecosystems. Currently, however, we have limited knowledge of DOM dynamics under low flow conditions as most previous studies have focused largely on storm event dynamics. Field deployable fluorescence technology offers new opportunities to explore diurnal DOM dynamics at finer time-steps and for longer periods than previously possible, thus providing new insights into in-stream DOM processing. In this study, we collected hourly fluorescence data (Spring - Fall) and a suite of hydro-climatological variables from two contrasting UK headwater watersheds: the urban Bourn Brook, Birmingham (52° 26' N, 1° 55' W) and agricultural Mill Haft, Shropshire (52° 48' N, 2° 14' W). We hypothesised that diurnal dynamics in humic-like fluorescence (Peak C; Ex. 365 nm / Em. 490 nm) would be driven by photo-oxidation processes; while tryptophan-like fluorescence (Peak T; Ex. 285 nm / Em. 345 nm) would respond to diurnal biomass production cycles. Wavelet analysis identified significant diurnal variations in Peak C for both the Bourn Brook and Mill Haft, with the strongest signal in early summer. While the amplitude was broadly similar between sites, peak timing and consistency differed, the Bourn Brook displayed peaks in the early morning (04:00 ± 2.2 h) and Mill Haft in early evening (19:00 ± 6.6 h). Cross wavelet analysis identified strong coherence with SW radiation for the urban stream but stronger relationships with discharge for the agricultural system. Hence, results from the Bourn Brook support our hypothesis regarding Peak C photo-oxidation processes but for Mill Haft, discharge (DOM dilution) appeared to be the key control. Contrary to our hypothesis, no strong diurnal pattern was identified for Peak T for either system. From this, we infer that the low levels of Peak T produced were rapidly taken up by bacteria and/or that productivity in these systems was low. Future work on in-stream DOM will benefit from improved integration of field deployable sensing and laboratory measurements.

Investigation of Natural Radioactivity in a Monazite Processing Plant in Japan.

PubMed

Iwaoka, Kazuki; Yajima, Kazuaki; Suzuki, Toshikazu; Yonehara, Hidenori; Hosoda, Masahiro; Tokonami, Shinji; Kanda, Reiko

2017-09-01

Monazite is a naturally occurring radioactive material that is processed for use in a variety of domestic applications. At present, there is little information available on potential radiation doses experienced by people working with monazite. The ambient dose rate and activity concentration of natural radionuclides in raw materials, products, and dust in work sites as well as the Rn and Rn concentrations in work sites were measured in a monazite processing plant in Japan. Dose estimations for plant workers were also conducted. The activity concentration of the U series in raw materials and products for the monazite processing plant was found to be higher than the relevant values described in the International Atomic Energy Agency Safety Standards. The ambient dose rates in the raw material yard were higher than those in other work sites. Moreover, the activity concentrations of dust in the milling site were higher than those in other work sites. The Rn concentrations in all work sites were almost the same as those in regular indoor environments in Japan. The Rn concentrations in all work sites were much higher than those in regular indoor environments in Japan. The maximum value of the effective dose for workers was 0.62 mSv y, which is lower than the reference level range (1-20 mSv y) for abnormally high levels of natural background radiation published in the International Commission of Radiological Protection Publication 103.

Process parameter dependent growth phenomena of naproxen nanosuspension manufactured by wet media milling.

PubMed

Bitterlich, A; Laabs, C; Krautstrunk, I; Dengler, M; Juhnke, M; Grandeury, A; Bunjes, H; Kwade, A

2015-05-01

The production of nanosuspensions has proved to be an effective method for overcoming bioavailability challenges of poorly water soluble drugs. Wet milling in stirred media mills and planetary ball mills has become an established top-down-method for producing such drug nanosuspensions. The quality of the resulting nanosuspension is determined by the stability against agglomeration on the one hand, and the process parameters of the mill on the other hand. In order to understand the occurring dependencies, a detailed screening study, not only on adequate stabilizers, but also on their optimum concentration was carried out for the active pharmaceutical ingredient (API) naproxen in a planetary ball mill. The type and concentration of the stabilizer had a pronounced influence on the minimum particle size obtained. With the best formulation the influence of the relevant process parameters on product quality was investigated to determine the grinding limit of naproxen. Besides the well known phenomenon of particle agglomeration, actual naproxen crystal growth and morphology alterations occurred during the process which has not been observed before. It was shown that, by adjusting the process parameters, those effects could be reduced or eliminated. Thus, besides real grinding and agglomeration a process parameter dependent ripening of the naproxen particles was identified to be a concurrent effect during the naproxen fine grinding process. Copyright © 2015 Elsevier B.V. All rights reserved.

Physiological changes in largemouth bass exposed to paper mill effluents under laboratory and field conditions

USGS Publications Warehouse

Sepulveda, M.S.; Gallagher, E.P.; Gross, T.S.

2004-01-01

We report here on studies designed to asses the effects of paper mill effluents on non-reproductive functions of free-ranging and captive Florida largemouth bass (Micropterus salmoides floridanus) This was accomplished by conducting an outdoor tank study, in which fish were exposed to well water or to 10%, 20%, 40%, and 80% full strength effluent for 28 or 56 days, and by sampling largemouth bass from sites within the St. Johns River, Florida, upstream and downstream from a paper mill plant. Blood and plasma samples from fish from the tank study and from fish sampled from the ambient sites were analyzed for over 20 variables. We also determined liver and spleen weights and examined them histologically. The most significant finding from the tank study was an increase in the concentration of albumin and hepatosomatic index for bass exposed to ???20% effluents for 56 days. Spleenosomatic index and number of melanomacrophage centers were decreased in bass from effluent-dominated sites (Palatka and Rice Creek), whereas concentrations of calcium, phosphorous, glucose, and creatinine were elevated in fish from these sites, compared to fish from reference streams. Fish from Rice Creek also had fewer red blood cells, and male bass from Palatka had lower concentrations of cholesterol. Plasma concentrations of albumin and hepatic concentrations of glutathione were elevated in males from Palatka, and both females and males from Rice Creek had higher concentrations of globulin. These results indicate a complex pattern of effects of paper mill effluents on several physiological functions. However, despite the myriad of treatment and site-related effects, most physiological parameters fell within normal ranges when compared to reports on largemouth bass and other freshwater species.

Uranium Mill Tailings Remedial Action Project Safety Advancement Field Effort (SAFE) Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-01

In 1992, the Uranium Mill Tailings Remedial Action (UMTRA) Project experienced several health and safety related incidents at active remediation project sites. As a result, the U.S. Department of Energy (DOE) directed the Technical Assistance Contractor (TAC) to establish a program increasing the DOE`s overall presence at operational remediation sites to identify and minimize risks in operations to the fullest extent possible (Attachments A and B). In response, the TAC, in cooperation with the DOE and the Remedial Action Contractor (RAC), developed the Safety Advancement Field Effort (SAFE) Program.

Analysis of Particle Distribution in Milled Al-Based Composites Reinforced by B4C Nanoparticles

NASA Astrophysics Data System (ADS)

Alihosseini, Hamid; Dehghani, Kamran

2017-04-01

In the present work, high-energy ball milling was employed to synthesize Al-(5-10 wt.%)B4C nanocomposite. To do this, two sizes of particles of 50 nm as nanoparticles (NPs) and 50 μm as coarse particles (CPs) were used. The morphology and microstructure of the milled powders were characterized using particle size analyzer, SEM, TEM and EDX techniques. It was found that milling time, B4C particles size and their content strongly affect the characteristics of powders during milling process. The breaking and cold welding of powders was recognized as two main competitive actions during the milling process that influence the microstructural evolutions. It was found that the presence of CPs led to the formation of microcracks which promote the fracture process of Al powders. The dominated mechanisms during the fabrication of composites and nanocomposites were discussed. Also, the theoretical issues regarding the changes in morphology and distribution of B4C particles in CPs and NPs are clarified.

12. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill: oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill: one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: Historical view, 1934, T.T. Waterman Collection, Hawaiian Sugar Planters' Association, Oahu, Hawaii. Masonry-lined passageway leading to the mill at the center of its circular masonry enclosure. The passageway permitted cane to be carried to the mill and cane trash (bagasse) to be carried away after milling. Bridges over the passageways, not in place, permitted the mill animals to circle and power the mill from above. View shows area prior to substantial overgrowth existing in 1978 views of the area. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Effects of uranium development on erosion and associated sedimentation in southern San Juan Basin, New Mexico

USGS Publications Warehouse

Cooley, Maurice E.

1979-01-01

A reconnaissance was made of some of the effects of uranium development on erosion and associated sedimentation in the southern San Juan Basin, where uranium development is concentrated. In general, the effects of exploration on erosion are minor, although erosion may be accelerated by the building of access roads, by activities at the drilling sites, and by close concentration of drilling sites. Areas where the greatest effects on erosion and sedimentation from mining and milling operations have occurred are: (1) in the immediate vicinity of mines and mills, (2) near waste piles, and (3) in stream channels where modifications, such as changes in depth have been caused by discharge of excess mine and mill water. Collapse of tailings piles could result in localized but excessive erosion and sedimentation.

Is the Internet Becoming a Bonanza for Diploma Mills?

ERIC Educational Resources Information Center

Guernsey, Lisa

1997-01-01

As the concept of earning a higher education degree at home becomes more accepted, diploma mills operating on the Internet proliferate. Students confuse unscrupulous institutions with legitimate distance education. Many use the World Wide Web as their primary marketing tool, with sites similar to those of accredited colleges, and do not appear to…

36 CFR 13.1904 - Kennecott Mines National Historic Landmark (KNHL).

Code of Federal Regulations, 2011 CFR

2011-07-01

..., DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Wrangell-St. Elias... and other mine openings; (c) Camping in or on any historic structure; and (d) Camping within the mill... center; and (e) Lighting or maintaining a fire within the mill site as defined in paragraph (d) of this...

Pulp capacity in the United States, 2000.

Treesearch

Brett R. Smith; Robert W. Rice; Peter J. Ince

2003-01-01

Production capacities of all woodpulp mills in the United States are identified by location, ownership, and process type. For each mill, production capacity is reported for the year 2000 by process type; total mill capacities are also reported for 1961, 1965, 1979, 1974, and 1983. In addition, the report summarizes the recent history and current status of woodpulp...

Leaders in Future and Current Technology Teaming Up to Improve Ethanol

Science.gov Websites

and NREL expertise to: Develop improvements in process throughput and water management for dry mill , Complete an overall process engineering model of the dry mill technology that identifies new ways to and operation of "dry mill" plants that currently produce ethanol from corn starch. Dry

Exposure pathway evaluations for sites that processed asbestos-contaminated vermiculite.

PubMed

Anderson, Barbara A; Dearwent, Steve M; Durant, James T; Dyken, Jill J; Freed, Jennifer A; Moore, Susan McAfee; Wheeler, John S

2005-01-01

The Agency for Toxic Substances and Disease Registry (ATSDR) is currently evaluating the potential public health impacts associated with the processing of asbestos-contaminated vermiculite at various facilities around the country. Vermiculite ore contaminated with significant levels of asbestos was mined and milled in Libby, Montana, from the early 1920s until 1990. The majority of the Libby ore was then shipped to processing facilities for exfoliation. ATSDR initiated the National Asbestos Exposure Review (NAER) to identify and evaluate exposure pathways associated with these processing facilities. This manuscript details ATSDR's phased approach in addressing exposure potential around these sites. As this is an ongoing project, only the results from a selected set of completed site analyses are presented. Historical occupational exposures are the most significant exposure pathway for the site evaluations completed to date. Former workers also probably brought asbestos fibers home on their clothing, shoes, and hair, and their household contacts may have been exposed. Currently, most site-related worker and community exposure pathways have been eliminated. One community exposure pathway of indeterminate significance is the current exposure of individuals through direct contact with waste rock brought home for personal use as fill material, driveway surfacing, or soil amendment. Trace levels of asbestos are present in soil at many of the sites and buried waste rock has been discovered at a few sites; therefore, future worker and community exposure associated with disturbing on-site soil during construction or redevelopment at these sites is also a potential exposure pathway.

Time-integrated Monitoring of Polychlorinated Dibenzo-p-dioxins and Polychlorinated Dibenzofurans (PCDD/Fs) in Urban and Industrial Wastewaters Using a Ceramic Toximeter and the CALUX Bioassay

PubMed Central

Addeck, Amr; Croes, Kim; Van Langenhove, Kersten; Denison, Michael S.; Elhamalawy, Ahmed; Elskens, Marc; Baeyens, Willy

2015-01-01

The ceramic toximeter as a passive sampler in combination with the CALUX bioassay was utilized as a time-integrated pollution-assessment technique for dioxin-like PCDD/Fs in wastewaters. Toximeters filled with XCARB and enclosed in stainless steel cages were submerged in wastewater of Belbeis drainage-canal and EMAK paper-mill, located in Egypt, for 28 days. Two samplers were removed every week from each site. Extracts from toximeters, from bottom-sediments, and from paper-mill sludge were analyzed by the CALUX. Results showed a regular increase in the amounts of PCDD/Fs trapped by the toximeters as sampling time increased. Time-weighted average concentrations (TWA) of PCDD/Fs in the wastewaters of the drainage-canal and paper-mill were 231 (214-281) and 26 (24.1-32.6) pg-BEQ L-1, respectively. Compared to literature data, this means a high pollution level for the drainage-canal water, while the pollution level in the paper-mill wastewater is similar to that reported for other paper mills. The PCDD/Fs levels in the drainage-canal bottom-sediments and in the paper-mill sludge were 8.3 and 14.6 pg-BEQ g-1 dry-weight, at the lower end of internationally reported values in similar compartments. The sampling rate of the tested toximeters for dissolved PCDD/Fs was about 3.6 mL d-1. Sediment/water partitioning coefficient log Kd of PCDD/Fs in the drainage-canal and the paper-mill was 1.42 and 2.70 respectively. The organic-carbon normalized partition coefficient log Koc was 4.17 and 3.19 respectively, and is lower than the reported values for other sites. PMID:24075528

Time-integrated monitoring of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in urban and industrial wastewaters using a ceramic toximeter and the CALUX bioassay.

PubMed

Addeck, Amr; Croes, Kim; Van Langenhove, Kersten; Denison, Michael S; Elhamalawy, Ahmed; Elskens, Marc; Baeyens, Willy

2014-01-01

The ceramic toximeter as a passive sampler in combination with the CALUX bioassay was utilized as a time-integrated pollution-assessment technique for dioxin-like PCDD/Fs in wastewaters. Toximeters filled with XCARB and enclosed in stainless steel cages were submerged in wastewater of Belbeis drainage-canal and EMAK paper-mill, located in Egypt, for 28 days. Two samplers were removed every week from each site. Extracts from toximeters, from bottom-sediments, and from paper-mill sludge were analyzed by the CALUX. Results showed a regular increase in the amounts of PCDD/Fs trapped by the toximeters as sampling time increased. Time-weighted average concentrations (TWA) of PCDD/Fs in the wastewaters of the drainage-canal and paper-mill were 231 (214-281) and 26 (24.1-32.6) pg-BEQL(-1), respectively. Compared to literature data, this means a high pollution level for the drainage-canal water, while the pollution level in the paper-mill wastewater is similar to that reported for other paper mills. The PCDD/Fs levels in the drainage-canal bottom-sediments and in the paper-mill sludge were 8.3 and 14.6 pg-BEQg(-1) dry-weight, at the lower end of internationally reported values in similar compartments. The sampling rate of the tested toximeters for dissolved PCDD/Fs was about 3.6 mL d(-1). Sediment/water partitioning coefficient logKd of PCDD/Fs in the drainage-canal and the paper-mill was 1.42 and 2.70 respectively. The organic-carbon normalized partition coefficient logKoc was 4.17 and 3.19 respectively, and is lower than the reported values for other sites. Copyright © 2013 Elsevier Ltd. All rights reserved.

Health assessment for Stamina Mills Site, North Smithfield, Providence County, Rhode Island, Region 1. CERCLIS No. RID980731442. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-11-15

The Stamina Mills site is on the National Priorities List (NPL). The environmental contamination of concern consists of methylene chloride, chromium, lead, nickel, trichloroethylene, perchloroethylene, and 1,2-dichloro- ethylene in groundwater; trichloroethylene, 1,2-dichloroethylene, methylene chloride, and nickel in surface water; trichloroethylene, 1,2-dichloroethylene, chloroform, methylene chloride, cyanide, 2-butanone, cadmium, lead, chromium, nickel, and dieldrin in soil; and chloroform, lead, nickel, and chromium in sediment. The site is considered to be of potential public health concern because of the risk to human health caused by the possibility of exposure to hazardous substances via soil, sediment, and surface water.

34. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill, oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill, one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: Side view of mill. Vertical drive shaft lying on ground in foreground. When drive-shaft was in upright position its bevel gear was meshed with the bevel gear of the top roll, transmitting the animals'circular motion around the drive shaft to the horizontal rolls. The foundation is of portland cement. The heavy timber mill bed, between the mill and the portland cement foundation has rolled away. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Degradation of TATP, TNT, and RDX using mechanically alloyed metals

NASA Technical Reports Server (NTRS)

Geiger, Cherie (Inventor); Sigman, Michael (Inventor); Fidler, Rebecca (Inventor); Clausen, Christian (Inventor)

2012-01-01

Bimetallic alloys prepared in a ball milling process, such as iron nickel (FeNi), iron palladium (FePd), and magnesium palladium (MgPd) provide in situ catalyst system for remediating and degrading nitro explosive compounds. Specifically, munitions, such as, 2,4,6-trinitrotoluene (TNT), cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX), nitrocellulose and nitroglycerine that have become contaminants in groundwater, soil, and other structures are treated on site to remediate explosive contamination.

Engineering and technology of industrial water power at Castleford Mills from the seventeenth century to the twentieth century

PubMed Central

Rollinson, Andrew N.

2016-01-01

This article tells the story of engineering and technology at Castleford Water Mills from the seventeenth century to the twentieth century through the presentation of recently discovered design plans and deeds, supplemented by other historical research. One of Castleford's mills was operated by Dr Thomas Allinson's Natural Food Company and therefore retained stoneground milling when fashions for white flour prompted other mills to switch to roller systems. The millstones were powered by a high-efficiency breastshot wheel, believed to be the last of its type taken out of industrial service in Britain. Many of its features, and its subsequent longevity, can be attributed to the influential works of William Fairbairn and John Smeaton. Detailed colour designs show the construction specifications of this water-wheel and its civil housing, along with other engineering plans such as a previously unrecorded Henry Simon horizontal turbine. Links with John Smeaton and the entry in his catalogue of designs for Castleford Oil Mill are also explored, and a former flood mill is identified at the site.

Response to Thermal Exposure of Ball-Milled Aluminum-Borax Powder Blends

NASA Astrophysics Data System (ADS)

Birol, Yucel

2013-04-01

Aluminum-borax powder mixtures were ball milled and heated above 873 K (600 °C) to produce Al-B master alloys. Ball-milled powder blends reveal interpenetrating layers of deformed aluminum and borax grains that are increasingly refined with increasing milling time. Thermal exposure of the ball-milled powder blends facilitates a series of thermite reactions between these layers. Borax, dehydrated during heating, is reduced by Al, and B thus generated reacts with excess Al to produce AlB2 particles dispersed across the aluminum grains starting at 873 K (600 °C). AlB2 particles start to form along the interface of the aluminum and borax layers. Once nucleated, these particles grow readily to become hexagonal-shaped crystals that traverse the aluminum grains with increasing temperatures as evidenced by the increase in the size as well as in the number of the AlB2 particles. Ball milling for 1 hour suffices to achieve a thermite reaction between borax and aluminum. Ball milling further does not impact the response of the powder blend to thermal exposure. The nucleation-reaction sites are multiplied, however, with increasing milling time and thus insure a higher number of smaller AlB2 particles. The size of the AlB2 platelets may be adjusted with the ball milling time.

Synthesis of Nano-Crystalline Cu-Cr Alloy by Mechanical Alloying

NASA Astrophysics Data System (ADS)

Sheibani, S.; Heshmati-Manesh, S.; Ataie, A.

In this paper, the influence of toluene as the process control agent (PCA) and pre-milling on the extension of solid solubility of 7 wt.% Cr in Cu by mechanical alloying in a high energy ball mill was investigated. The structural evolution and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques, respectively. The solid solution formation at different conditions was analyzed by copper lattice parameter change during the milling process. It was found that both the presence of PCA and pre-milling of Cr powder lead to faster dissolution of Cr. The mean crystallite size was also calculated and showed to be about 10 nm after 80 hours of milling.

Cavity formation and surface modeling of laser milling process under a thin-flowing water layer

NASA Astrophysics Data System (ADS)

Tangwarodomnukun, Viboon

2016-11-01

Laser milling process normally involves a number of laser scans over a workpiece to selectively remove the material and then to form cavities with shape and dimensions required. However, this process adversely causes a heat accumulation in work material, which can in turn damage the laser-milled area and vicinity in terms of recast deposition and change of material properties. Laser milling process performing in a thin-flowing water layer is a promising method that can overcome such damage. With the use of this technique, water can flush away the cut debris and at the same time cool the workpiece during the ablation. To understand the potential of this technique for milling application, the effects of process parameters on cavity dimensions and surface roughness were experimentally examined in this study. Titanium sheet was used as a workpiece to be milled by a nanosecond pulse laser under different water flow velocities. A smooth and uniform cut feature can be obtained when the metal was ablated under the high laser pulse frequency and high water flow velocity. Furthermore, a surface model based on the energy balance was developed in this study to predict the cavity profile and surface roughness. By comparing to the experiments, the predicted profiles had a good agreement with the measured ones.

2013 Annual Site Inspection and Monitoring Report for Uranium Mill Tailings Radiation Control Act Title I Disposal Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

This report, in fulfillment of a license requirement, presents the results of long-term surveillance and maintenance activities conducted by the U.S. Department of Energy (DOE) Office of Legacy Management (LM) in 2013 at 19 uranium mill tailings disposal sites established under Title I of the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978.1 These activities verified that the UMTRCA Title I disposal sites remain in compliance with license requirements. DOE operates 18 UMTRCA Title I sites under a general license granted by the U.S. Nuclear Regulatory Commission (NRC) in accordance with Title 10 Code of Federal Regulations Part 40.27more » (10 CFR 40.27). As required under the general license, a long-term surveillance plan (LTSP) for each site was prepared by DOE and accepted by NRC. The Grand Junction, Colorado, Disposal Site, one of the 19 Title I sites, will not be included under the general license until the open, operating portion of the cell is closed. The open portion will be closed either when it is filled or in 2023. This site is inspected in accordance with an interim LTSP. Long-term surveillance and maintenance services for these disposal sites include inspecting and maintaining the sites; monitoring environmental media and institutional controls; conducting any necessary corrective actions; and performing administrative, records, stakeholder relations, and other regulatory stewardship functions. Annual site inspections and monitoring are conducted in accordance with site-specific LTSPs and procedures established by DOE to comply with license requirements. Each site inspection is performed to verify the integrity of visible features at the site; to identify changes or new conditions that may affect the long-term performance of the site; and to determine the need, if any, for maintenance, follow-up or contingency inspections, or corrective action in accordance with the LTSP. LTSPs and site compliance reports are available on the Internet at http://www.lm.doe.gov/.« less

Influence of ball milling on atomic structure and magnetic properties of Co{sub 40}Fe{sub 22}Ta{sub 8}B{sub 30} glassy alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taghvaei, Amir Hossein, E-mail: Amirtaghvaei@gmail.com; Department of Materials Science and Engineering, Shiraz University of Technology, Shiraz; Stoica, Mihai

2014-06-01

The influence of ball milling on the atomic structure and magnetic properties of the Co{sub 40}Fe{sub 22}Ta{sub 8}B{sub 30} metallic glass with a high thermal stability and excellent soft magnetic properties has been investigated. After 14 h of milling, the obtained powders were found to consist mainly of an amorphous phase and a small fraction of the (Co,Fe){sub 21}Ta{sub 2}B{sub 6} nanocrystals. The changes in the reduced pair correlation functions suggest noticeable changes in the atomic structure of the amorphous upon ball milling. Furthermore, it has been shown that milling is accompanied by introduction of compressive and dilatational sites inmore » the glassy phase and increasing the fluctuation of the atomic-level hydrostatic stress without affecting the coordination number of the nearest neighbors. Ball milling has decreased the thermal stability and significantly affected the magnetic properties through increasing the saturation magnetization, Curie temperature of the amorphous phase and coercivity. - Highlights: • Ball milling affected the atomic structure of Co{sub 40}Fe{sub 22}Ta{sub 8}B{sub 30} metallic glass. • Mechanically-induced crystallization started after 4 h milling. • Milling increased the fluctuation of the atomic-level hydrostatic stress in glass. • Ball milling influenced the thermal stability and magnetic properties.« less

Arsenic sorption by nanocrystalline magnetite: an example of environmentally promising interface with geosphere.

PubMed

Bujňáková, Z; Baláž, P; Zorkovská, A; Sayagués, M J; Kováč, J; Timko, M

2013-11-15

In this paper, the sorption of arsenic onto nanocrystalline magnetite mineral Fe3O4 was studied in a model system. Nanocrystalline magnetite was produced by mechanical activation in a planetary ball mill from natural microcrystalline magnetite. As a consequence of milling, the specific surface area increased from 0.1m(2)/g to 11.9 m(2)/g and the surface site concentration enhanced from 2.2 sites/nm(2) to 8.4 sites/nm(2). These changes in surface properties of magnetite lead to the enhancement of arsenic removal from model system. The best sorption ability was achieved with magnetite sample activated for 90 min. In this case the sample was able to absorb around 4 mg/g. The structural changes of magnetite were also observed and the new hematite phase was detected after 120 min of milling. A good correlation between the decreasing particle size, increasing specific surface area and reduction of saturation magnetization was found. In desorption study, KOH and NaOH were found as the best eluents where more than 70% of arsenic was released back into the solution. The principal novelty of the paper is that mineral magnetite, truly one nature's gift can be used after "smart" milling (mechanical activation) as an effective arsenic sorbent. Copyright © 2013 Elsevier B.V. All rights reserved.

Rough mill simulator version 3.0: an analysis tool for refining rough mill operations

Treesearch

Edward Thomas; Joel Weiss

2006-01-01

ROMI-3 is a rough mill computer simulation package designed to be used by both rip-first and chop-first rough mill operators and researchers. ROMI-3 allows users to model and examine the complex relationships among cutting bill, lumber grade mix, processing options, and their impact on rough mill yield and efficiency. Integrated into the ROMI-3 software is a new least-...

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi Method

NASA Astrophysics Data System (ADS)

Hazza Faizi Al-Hazza, Muataz; Ibrahim, Nur Asmawiyah bt; Adesta, Erry T. Y.; Khan, Ahsan Ali; Abdullah Sidek, Atiah Bt.

2017-03-01

One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed milling, hard milling and dry milling. However, one of the most important challenges in this process is to control the flank wear rate. Therefore a analyzing the flank wear rate during machining should be investigated in order to determine the best cutting levels that will not affect the final quality of the product. In this research Taguchi method has been used to investigate the effect of cutting speed, feed rate and depth of cut and determine the best level s to minimize the flank wear rate up to total length of 0.3mm based on the ISO standard to maintain the finishing requirements.

Effect of milling time on microstructure and mechanical properties of Cu-Ni-graphite composites

NASA Astrophysics Data System (ADS)

Wang, Yiran; Gao, Yimin; Li, Yefei; Zhang, Chao; Huang, Xiaoyu; Zhai, Wenyan

2017-09-01

Cu-Ni-graphite composites are intended for application in switch slide baseplate materials. The microstructure of the composites depends strongly on the ball milling time, and a suitable time can significantly improve the properties of the Cu-Ni-graphite composites. In this study, a two-step milling method was employed. The morphology evolution and microstructural features of the powder was characterized at different milling times. Afterwards, the Cu-Ni-graphite composites were prepared in the process of cold pressing, sintering, re-pressing and re-sintering as a function of the different milling times. Finally, both the microstructure and mechanical properties of the Cu-Ni-graphite composites are discussed. The results show that no new phase was generated during the milling process. The morphology evolution of the mixture of Cu/Ni powder changed from spherical-like to cubic-like, plate-like and flake-like with an increasing milling time. The microstructure of the composites consisted of α-phase and graphite. The boundary area and quantity of pores changed as the milling time increased. The relative density, hardness and flexural strength reached maximum values at 15 h of milling time.

Biomechanical properties of wheat grains: the implications on milling.

PubMed

Hourston, James E; Ignatz, Michael; Reith, Martin; Leubner-Metzger, Gerhard; Steinbrecher, Tina

2017-01-01

Millennia of continuous innovation have driven ever increasing efficiency in the milling process. Mechanically characterizing wheat grains and discerning the structure and function of the wheat bran layers can contribute to continuing innovation. We present novel shear force and puncture force testing regimes to characterize different wheat grain cultivars. The forces endured by wheat grains during the milling process can be quantified, enabling us to measure the impact of commonly applied grain pretreatments, such as microwave heating, extended tempering, enzyme and hormone treatments on grains of different 'hardness'. Using these methods, we demonstrate the importance of short tempering phases prior to milling and identify ways in which our methods can detect differences in the maximum force, energy and breaking behaviours of hard and soft grain types. We also demonstrate for the first time, endosperm weakening in wheat, through hormone stratification on single bran layers. The modern milling process is highly refined, meaning that small, cultivar specific, adjustments can result in large increases in downstream profits. We believe that methods such as these, which enable rapid testing of milling pretreatments and material properties can help to drive an innovation process that has been core to our industrial efforts since prehistory. © 2017 The Authors.

Biomechanical properties of wheat grains: the implications on milling

PubMed Central

Reith, Martin

2017-01-01

Millennia of continuous innovation have driven ever increasing efficiency in the milling process. Mechanically characterizing wheat grains and discerning the structure and function of the wheat bran layers can contribute to continuing innovation. We present novel shear force and puncture force testing regimes to characterize different wheat grain cultivars. The forces endured by wheat grains during the milling process can be quantified, enabling us to measure the impact of commonly applied grain pretreatments, such as microwave heating, extended tempering, enzyme and hormone treatments on grains of different ‘hardness’. Using these methods, we demonstrate the importance of short tempering phases prior to milling and identify ways in which our methods can detect differences in the maximum force, energy and breaking behaviours of hard and soft grain types. We also demonstrate for the first time, endosperm weakening in wheat, through hormone stratification on single bran layers. The modern milling process is highly refined, meaning that small, cultivar specific, adjustments can result in large increases in downstream profits. We believe that methods such as these, which enable rapid testing of milling pretreatments and material properties can help to drive an innovation process that has been core to our industrial efforts since prehistory. PMID:28100826

Responses of shortfin eel (Anguilla australis) exposed in situ to pulp and paper effluent.

PubMed

van den Heuvel, Michael R; Landman, Michael J; Tremblay, Louis A

2006-10-01

The responses of shortfin eel (Anguilla australis) to discharges from two pulp and paper mills, municipal wastewater, and a geothermal power plant wastewater were examined. Eels were caged at 3 sites along the Tarawera River, North Island, New Zealand, to explore effects of a 3-wk exposure down a contamination gradient (Ref --> D1 --> D2). Most of the observed effects were seen in eels caged at the furthest downstream site (D2), below all the discharge areas. General hematology in eels was unaffected, as measures did not differ markedly at the two downstream sites compared with the reference site. At D2, eels were significantly lighter per unit length (reduced condition factor), although liver and spleen size (LSI and SSI) were unaffected. Significantly elevated circulating sex steroid concentrations (testosterone and estradiol) were measured in D2 eels and increasing sex steroid levels at both sites downstream of the reference site were observed. Significant ethoxyresorufin O-deethylase (EROD) activity induction was seen in D2 eels and bile chemistry showed significant accumulation of pyrene and retene equivalents. However, significantly greater concentrations of total resin acids were found in the bile of eels from the intermediate site (D1), between the two pulp and paper mills. The higher polycyclic aromatic hydrocarbon (PAH) equivalents found in the bile of D2 eels suggest that resin acid neutrals, particularly retene, are responsible for some of the effects observed in eels at the furthest downstream exposure site. Levels of pulp and paper mill extractives in sediment, including the PAH retene, support this conclusion.

76 FR 70170 - Proposed Alternative Soils Standards for the Uravan, Colorado Uranium Mill

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... identified four discrete areas that are not in full compliance with the soil remediation standards. The... State of Colorado and the EPA to proceed with delisting the Uravan site from the NPL. Four discrete... four discrete areas are referred to as: the Mill Hillside Area; A-Plant North Area; River Ponds Area...

Impacts of prescribed fire on Pinus rigida Mill

Treesearch

Nicholas J. Carlo; Heidi J. Renninger; Kenneth L. Clark; Karina V.R. Schäfer

2016-01-01

A comparative analysis of the impacts of prescribed fire on three upland forest stands in the Northeastern Atlantic Plain, NJ, USA, was conducted. Effects of prescribed fire on water use and gas exchange of overstory pines were estimated via sap-flux rates and photosynthetic measurements on Pinus rigida Mill. Each study site had two sap-flux plots...

Cloud-based application for rice moisture content measurement using image processing technique and perceptron neural network

NASA Astrophysics Data System (ADS)

Cruz, Febus Reidj G.; Padilla, Dionis A.; Hortinela, Carlos C.; Bucog, Krissel C.; Sarto, Mildred C.; Sia, Nirlu Sebastian A.; Chung, Wen-Yaw

2017-02-01

This study is about the determination of moisture content of milled rice using image processing technique and perceptron neural network algorithm. The algorithm involves several inputs that produces an output which is the moisture content of the milled rice. Several types of milled rice are used in this study, namely: Jasmine, Kokuyu, 5-Star, Ifugao, Malagkit, and NFA rice. The captured images are processed using MATLAB R2013a software. There is a USB dongle connected to the router which provided internet connection for online web access. The GizDuino IOT-644 is used for handling the temperature and humidity sensor, and for sending and receiving of data from computer to the cloud storage. The result is compared to the actual moisture content range using a moisture tester for milled rice. Based on results, this study provided accurate data in determining the moisture content of the milled rice.

The FEM Simulation on End Mill of Plastic Doors and Windows Corner Cleaning Based on Deform-3D

NASA Astrophysics Data System (ADS)

Li, Guoping; Huang, Zhenyong; Wang, Xiaohui

2017-12-01

In the plastic doors and windows corner cleaning process, the rotating speed, the feed rate and the milling cutter diameter are the main factors that affect the efficiency and quality of the of corner cleaning. In this paper, SolidWorks will be used to establish the 3D model of end mills, and use Deform-3D to research the end mill milling process. And using orthogonal experiment design method to analyze the effect of rotating speed, the feed rate and the milling cutter diameter on the axial force variation, and to get the overall trend of axial force and the selection of various parameters according to the influence of axial force change. Finally, simulate milling experiment used to get the actual axial force data to verify the reliability of the FEM simulation model. And the conclusion obtained in this paper has important theoretical value in improving the plastic doors and windows corner cleaning efficiency and quality.

Kaolinosis in a cotton mill worker.

PubMed

Levin, J L; Frank, A L; Williams, M G; McConnell, W; Suzuki, Y; Dodson, R F

1996-02-01

A 62-year-old white male employed for 43 years in the polishing room of a cotton textile mill was admitted to a tertiary care center with progressive dyspnea and productive cough that had not responded to therapy for tuberculosis. In spite of aggressive antibiotic therapy and respiratory support, the patient died as a consequence of respiratory failure. Small rounded and irregular opacities had been noted on the chest radiograph. Review of job-site spirometry demonstrated a worsening restrictive pattern over a 4-year period prior to his death. Additional occupational history revealed long-term exposure to kaolin in the polishing room, and pathologic examination of lung tissue confirmed extensive fibrosis and substantial quantities of kaolin. Kaolinosis is a disease typically found among individuals involved in mining or processing this material rather than in user industries. This case illustrates the importance of obtaining a complete occupational history in reaching a diagnosis. The clinicopathologic aspects of kaolinosis are also reviewed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rounaghi, S.A., E-mail: s.a.rounaghi@gmail.com; Kiani Rashid, A.R.; Eshghi, H., E-mail: heshghi@ferdowsi.um.ac.ir

Decomposition of melamine was studied by solid state reaction of melamine and aluminum powders during high energy ball-milling. The milling procedure performed for both pure melamine and melamine/Al mixed powders as the starting materials for various times up to 48 h under ambient atmosphere. The products were characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The results revealed that Al causes melamine deammoniation at the first stages of milling and further milling process leads to the s-triazine ring degradation while nano-crystallite hexagonal aluminum nitride (h-AlN) was the main solid product. Comparison to milling process, the possibility ofmore » the reaction of melamine with Al was also investigated by thermal treatment method using differential scanning calorimeter (DSC) and thermo gravimetric analyzer (TGA). Melamine decomposition occurred by thermal treatment in the range of 270-370 Degree-Sign C, but no reaction between melamine and aluminum was observed. - Graphical Abstract: Mechanochemical reaction of melamine with Al resulted in the formation of nanocrystalline AlN after 7 h milling time Highlights: Black-Right-Pointing-Pointer High energy ball milling of melamine and aluminum results decomposition of melamine with elimination of ammonia. Black-Right-Pointing-Pointer Nano-crystalline AlN was synthesized by the mechanochemical route. Black-Right-Pointing-Pointer Milling process has no conspicuous effect on pure melamine degradation. Black-Right-Pointing-Pointer No reaction takes place by heating melamine and aluminum powder mixture in argon.« less

Activity of Plodia interpunctella (Lepidoptera: Pyralidae) in and around flour mills.

PubMed

Doud, C W; Phillips, T W

2000-12-01

Studies were conducted at two flour mills where male Indian meal moths, Plodia interpunctella (Hübner), were captured using pheromone-baited traps. Objectives were to determine the distribution of male P. interpunctella at different locations in and around the mills throughout the season, and to monitor moth activity before and after one of the mills was fumigated with methyl bromide to assess efficacy of treatment. Commercially available sticky traps baited with the P. interpunctella sex pheromone were placed at various locations outside and within the larger of the two mills (mill 1). Moths were captured inside mill 1 after methyl bromide fumigations. The highest numbers of P. interpunctella were caught outside the facility and at ground floor locations near outside openings. Additional traps placed in the rooms above the concrete stored-wheat silos at mill 1 during the second year captured more moths than did traps within the mill's production and warehouse areas. In another study, moths were trapped at various distances from a smaller flour mill (mill 2) to determine the distribution of moths outdoors relative to the mill. There was a negative correlation between moth capture and distance from the facility, which suggested that moth activity was concentrated at or near the flour mill. The effectiveness of the methyl bromide fumigations in suppressing moth populations could not be assessed with certainty because moths captured after fumigation may have immigrated from outside through opened loading bay warehouse doors. This study documents high levels of P. interpunctella outdoors relative to those recorded inside a food processing facility. Potential for immigration of P. interpunctella into flour mills and other stored product facilities from other sources may be greater than previously recognized. Moth entry into a food processing facility after fumigation is a problem that should be addressed by pest managers.

Preparation of folic acid conjugated hematite nanoparticles using high energy ball milling for biomedical applications

NASA Astrophysics Data System (ADS)

Sahu, Dwipak Prasad; Jammalamadaka, S. Narayana

2018-04-01

The controlled release and targeted delivery of drug to tumour sites using magnetic nanoparticles (MNPs) for the treatment of cancer & other ailments is current focus of research. Here we describe our efforts in functionalization of hematite nanoparticles α-Fe2O3 with polyethylene glycol (PEG) and activation with Folic Acid (FA) (ligand) using a high energy ball milling process. An extra peak at 48.3° in XRD hints an encapsulation of polyethylene glycol on α-Fe2O3 nanoparticles (NPs). The decrease in the intensity of absorption spectra peaks in UV - Vis NIR spectrum pertinent to activated α-Fe2O3 NPs indicate indeed there is a conjugation of folic acid on top of PEG. Thermo-gravimetric analysis shows 5% weight loss for the activated α-Fe2O3 NPs due to desorption of chemi-adsorbed PEG from NPs and its further decomposition. Magnetization measurements indicates indeed the coercivity persists even after activating the NPs with FA. We believe presence of coercivity in MNPs can be exploited in magnetic hyperthermia treatment of cancer cell by applying suitable amount of field at the targeted site.

Green plants as solar energy converters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1976-06-01

A survey covers the potential of energy production from biomass and solid wastes; various processes for the combustion of wastes, such as the co-combustion of solid waste and sewage sludge at the St. Paul/Seneca Treatment Plant Sludge Incinerator; various biological processes for the conversion of solid wastes to fuel such as the Institute of Gas Technology 400 l. digestor for the biogasification of municipal solid waste and sewage solids to a methane-rich product gas; the use of industrial wastes for fuel, such as slash and mill residues used as fuel in lumber mills; the biogasification of animal wastes by usingmore » small-scale on-site digesters to produce methane gas for cooking and lighting; energy farming methods, such as growing giant California kelp, sargassum, and plankton as suitable feedstock for the production of methane, fertilizers, and food; problems, such as the possible alteration of the reflectivity of large areas of the earth's surface by rapidly growing plants raised for biomass; and benefits such as the reduction in air, water, and land pollution associated with the use of wastes and biomass grown especially for energy.« less

ROMI-3: Rough-Mill Simulator Version 3.0: User's Guide

Treesearch

Joel M. Weiss; R. Edward Thomas; R. Edward Thomas

2005-01-01

ROMI-3 Rough-Mill Simulator is a software package that simulates current industrial practices for rip-first and chop-first lumber processing. This guide shows the user how to set up and examine the results of simulations of current or proposed mill practices. ROMI-3 accepts cutting bills with as many as 600 combined solid and/or panel part sizes. Plots of processed...

Ball milling: An experimental support to the energy transfer evaluated by the collision model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magini, M.; Iasonna, A.; Padella, F.

1996-01-01

In recent years several attempts have been made in order to understand the fundamentals of the ball milling process. The aim of these approaches is to establish predictive capabilities for this process, i.e. the possibility of obtaining a given product by suitable choosing the proper milling conditions. Maurice and Courtney have modeled ball milling in a planetary and in a vibratory mill including parameters like impact times, areas of the colliding surfaces (derived from hertzian collision theory), powder strain rates and pressure peak during collision. Burgio et al derived the kinematic equations of a ball moving on a planetary millmore » and the consequent ball-to-powder energy transfer occurring in a single collision event. The fraction of input energy transferred to the powder was subsequently estimated by an analysis of the collision event. Finally an energy map was constructed which was the basis for a model with predictive capabilities. The aim of the present article is to show that the arguments used to construct the model of the milling process has substantial experimental support.« less

Modeling of Surface Geometric Structure State After Integratedformed Milling and Finish Burnishing

NASA Astrophysics Data System (ADS)

Berczyński, Stefan; Grochała, Daniel; Grządziel, Zenon

2017-06-01

The article deals with computer-based modeling of burnishing a surface previously milled with a spherical cutter. This method of milling leaves traces, mainly asperities caused by the cutting crossfeed and cutter diameter. The burnishing process - surface plastic treatment - is accompanied by phenomena that take place right in the burnishing ball-milled surface contact zone. The authors present the method for preparing a finite element model and the methodology of tests for the assessment of height parameters of a surface geometrical structure (SGS). In the physical model the workpieces had a cuboidal shape and these dimensions: (width × height × length) 2×1×4.5 mm. As in the process of burnishing a cuboidal workpiece is affected by plastic deformations, the nonlinearities of the milled item were taken into account. The physical model of the process assumed that the burnishing ball would be rolled perpendicularly to milling cutter linear traces. The model tests included the application of three different burnishing forces: 250 N, 500 N and 1000 N. The process modeling featured the contact and pressing of a ball into the workpiece surface till the desired force was attained, then the burnishing ball was rolled along the surface section of 2 mm, and the burnishing force was gradually reduced till the ball left the contact zone. While rolling, the burnishing ball turned by a 23° angle. The cumulative diagrams depict plastic deformations of the modeled surfaces after milling and burnishing with defined force values. The roughness of idealized milled surface was calculated for the physical model under consideration, i.e. in an elementary section between profile peaks spaced at intervals of crossfeed passes, where the milling feed fwm = 0.5 mm. Also, asperities after burnishing were calculated for the same section. The differences of the obtained values fall below 20% of mean values recorded during empirical experiments. The adopted simplification in after-milling SGS modeling enables substantial acceleration of the computing process. There is a visible reduction of the Ra parameter value for milled and burnished surfaces as the burnishing force rises. The tests determined an optimal burnishing force at a level of 500 N (lowest Ra = 0.24 μm). Further increase in the value of burnishing force turned out not to affect the surface roughness, which is consistent with the results obtained from experimental studies.

The dispersion of fine chitosan particles by beads-milling

NASA Astrophysics Data System (ADS)

Rochima, Emma; Utami, Safira; Hamdani, Herman; Azhary, Sundoro Yoga; Praseptiangga, Danar; Joni, I. Made; Panatarani, Camellia

2018-02-01

This research aimed to produce fine chitosan particles from a crab shell waste by beads-milling method by two different concentration of PEG as dispersing agent (150 and 300 wt. %). The characterization was performed to obtain the size and size distribution, the characteristics of functional groups and the degree of deacetylation. The results showed that the chitosan fine particles was obtained with a milling time 120 minutes with the best concentration of PEG 400 150 wt. %. The average particle size of the as-prepared suspension is 584 nm after addition of acetic acid solution (1%, v/v). Beads milling process did not change the glucosamine and N-acetylglucosamine content on chitosan structure which is indicated by degree of deacetylation higher than 70%. It was concluded that beads milling process can be applied to prepare chitosan fineparticles by proper adjustment in the milling time, pH and dosage of dispersing agent.

The use of inverse phase gas chromatography to measure the surface energy of crystalline, amorphous, and recently milled lactose.

PubMed

Newell, H E; Buckton, G; Butler, D A; Thielmann, F; Williams, D R

2001-05-01

To assess differences in surface energy due to processing induced disorder and to understand whether the disorder dominated the surfaces of particles. Inverse gas chromatography was used to compare the surface energies of crystalline, amorphous, and ball milled lactose. The milling process made ca 1% of the lactose amorphous, however the dispersive contribution to surface energy was 31.2, 37.1, and 41.6 mJ m(-2) for crystalline, spray dried and milled lactose, respectively. A physical mixture of crystalline (99%) and amorphous (1%) material had a dispersive surface energy of 31.5 mJ m(-2). Milling had made the surface energy similar to that of the amorphous material in a manner that was very different to a physical mixture of the same amorphous content. The milled material will have similar interfacial interactions to the 100% amorphous material.

Synthesis and characterization of nanocrystalline Co-Fe-Nb-Ta-B alloy

NASA Astrophysics Data System (ADS)

Raanaei, Hossein; Fakhraee, Morteza

2017-09-01

In this research work, structural and magnetic evolution of Co57Fe13Nb8Ta4B18 alloy, during mechanical alloying process, have been investigated by using, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, electron dispersive X-ray spectroscopy, differential thermal analysis and also vibrating sample magnetometer. It is observed that at 120 milling time, the crystallite size reaches to about 7.8 nm. Structural analyses show that, the solid solution of the initial powder mixture occurs at160 h milling time. The coercivity behavior demonstrates a rise, up to 70 h followed by decreasing tendency up to final stage of milling process. Thermal analysis of 160 h milling time sample reveals two endothermic peaks. The characterization of annealed milled sample for 160 h milling time at 427 °C shows crystallite size growth accompanied by increasing in saturation magnetization.

Nuclear facility decommissioning and site remedial actions. Volume 6. A selected bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owen, P.T.; Michelson, D.C.; Knox, N.P.

1985-09-01

This bibliography of 683 references with abstracts on the subject of nuclear facility decommissioning, uranium mill tailings management, and site remedial actions is the sixth in a series of annual reports prepared for the US Department of Energy's Remedial Action Programs. Foreign as well as domestic literature of all types - technical reports, progress reports, journal articles, conference papers, symposium proceedings, theses, books, patents, legislation, and research project descriptions - has been included. The bibliography contains scientific (basic research as well as applied technology), economic, regulatory, and legal literature pertinent to the US Department of Energy's remedial action program. Majormore » chapters are: (1) Surplus Facilities Management Program; (2) Nuclear Facilities Decommissioning; (3) Formerly Utilized Sites Remedial Action Program; (4) Facilities Contaminated with Natural Radioactivity; (5) Uranium Mill Tailings Remedial Action Program; (6) Grand Junction Remedial Action Program; (7) Uranium Mill Tailings Management; (8) Technical Measurements Center; and (9) General Remedial Action Program Studies. Chapter sections for chapters 1, 2, 5, and 7 include Design, Planning, and Regulations; Environmental Studies and Site Surveys; Health, Safety, and Biomedical Studies; Decontamination Studies; Dismantlement and Demolition; Site Stabilization and Reclamation; Waste Disposal; Remedial Action Experience; and General Studies. The references within each chapter or section are arranged alphabetically by leading author. References having no individual author are arranged by corporate affiliation or by publication description.« less

Exposure to biohazards in wood dust: bacteria, fungi, endotoxins, and (1-->3)-beta-D-glucans.

PubMed

Alwis, K U; Mandryk, J; Hocking, A D

1999-09-01

Personal exposure to fungi, bacteria, endotoxin, and (1-->3)-beta-D-glucan was determined at different woodworking sites--logging sites, sawmills, woodchipping sites, and joineries. Exposure levels to fungi at logging sites and sawmills were in the range of 10(3)-10(4) cfu/m3, at the woodchipping mill, 10(3)-10(5) cfu/m3, and at joineries, 10(2)-10(4) cfu/m3. Although mean endotoxin levels were lower than the suggested threshold value of 20 ng/m3, some personal exposures at sawmills and a joinery exceeded the standard. The geometric mean personal (1-->3)-beta-D-glucan exposure level at the woodchipping mill was 2.32 ng/m3, at sawmills, 1.37 ng/m3, at logging sites, 2.02 ng/m3, and at joineries, 0.43 ng/m3. Highly significant associations were found between mean personal inhalable endotoxin exposures and Gram-negative bacteria levels (p < 0.0001), and mean personal inhalable (1-->3)-beta-D-glucan exposures and fungi levels (p = 0.0003). The prevalence of cough, phlegm, chronic bronchitis, nasal symptoms, frequent headaches, and eye and throat irritations was significantly higher among woodworkers than controls. Dose-response relationships were found between personal exposures and work-related symptoms among joinery workers and sawmill and chip mill workers.

Esthetic considerations for the treatment of the edentulous maxilla based on current informatic alternatives: a case report.

PubMed

Rodríguez-Tizcareño, Mario H; Barajas, Lizbeth; Pérez-Gásque, Marisol; Gómez, Salvador

2012-06-01

This report presents a protocol used to transfer the virtual treatment plan data to the surgical and prosthetic reality and its clinical application, bone site augmentation with computer-custom milled bovine bone graft blocks to their ideal architecture form, implant insertion based on image-guided stent fabrication, and the restorative manufacturing process through computed tomography-based software programs and navigation systems and the computer-aided design and manufacturing techniques for the treatment of the edentulous maxilla.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dam, William; Gil, Dr. April; Johnson, Raymond H.

The US Department of Energy Office of Legacy Management (LM) is responsible for maintaining protective public health and environmental conditions at former uranium mill tailings sites nationwide via long-term stewardship. One of these sites, a former uranium mill near Riverton, Wyoming, is within the boundary of the Wind River Indian Reservation and operated from 1958 to 1963. Tailings and contaminated material associated with mill operations were removed and transported to an offsite disposal cell in 1989. The remedial action was completed under Title I of the Uranium Mill Tailings Radiation Control Act of 1978. Milling operations, which included an unlinedmore » tailings impoundment and an unlined evaporation pond, contaminated the shallow groundwater, resulting in a downgradient groundwater plume that discharges to the Little Wind River. A natural flushing compliance strategy was implemented in 1998. This strategy allows contaminants of concern to naturally flush from the groundwater, provided that contaminants flush below US Environmental Protection Agency maximum concentration limits within 100 years. As part of the compliance strategy, LM has implemented a groundwater monitoring program along with institutional controls that include the installation of an alternate water supply, continued sampling of private wells, and restrictions on well drilling and gravel pit construction. LM works closely with local stakeholders and community members to ensure that these institutional controls are in place and maintained. The Riverton site provides an interesting case study where contaminant remobilization due to river flooding prompted a reevaluation of the conceptual site model to verify if the current compliance strategy would remain protective of human health and the environment. Concentrations of groundwater contaminants, which include sulfate, molybdenum, and uranium, were transiently elevated following flooding of the Little Wind River in 2010 and 2016. These flood events provided the impetus to investigate other aspects of the hydrologic system, including the unsaturated zone, naturally reduced (sulfidic) zones, and evaporite deposits. New site conceptual models, field and laboratory studies, and numerical models are being developed to explain how biogeochemical sediment–water interactions contribute to plume persistence and flood-related increases in groundwater concentrations. Updated human health and ecological risk assessments are progressing to evaluate the risk to human health and the environment based on current site conditions. Groundwater concentrations may remain above US Environmental Protection Agency maximum concentration limits beyond the 100-year natural flushing regulatory time frame. LM in its capacity as a long-term steward continues to monitor the site to ensure protectiveness is maintained and to determine the feasibility of alternative compliance and remediation strategies.« less

Carotenoid Stability during Dry Milling, Storage, and Extrusion Processing of Biofortified Maize Genotypes.

PubMed

Ortiz, Darwin; Ponrajan, Amudhan; Bonnet, Juan Pablo; Rocheford, Torbert; Ferruzzi, Mario G

2018-05-09

Translation of the breeding efforts designed to biofortify maize ( Z. mays) genotypes with higher levels of provitamin A carotenoid (pVAC) content for sub-Saharan Africa is dependent in part on the stability of carotenoids during postharvest through industrial and in-home food processing operations. The purpose of this study was to simulate production of commercial milled products by determining the impact of dry milling and extrusion processing on carotenoid stability in three higher pVAC maize genotypes (C17xDE3, Orange ISO, Hi27xCML328). Pericarp and germ removal of biofortified maize kernels resulted in ∼10% loss of total carotenoids. Separating out the maize flour fraction (<212 μm) resulted in an additional ∼15% loss of total carotenoids. Carotenoid degradation was similar across milled maize fractions. Dry-milled products of Orange ISO and Hi27xCML328 genotypes showed ∼28% pVAC loss after 90-days storage. Genotype C17xDE3, with highest levels of all- trans-β-carotene, showed a 68% pVAC loss after 90-day storage. Extrusion processing conditions were optimal at 35% extrusion moisture, producing fully cooked instant maize flours with high pVAC retention (70-93%). These results support the notion that postharvest losses in maize milled fractions may be dependent, in part, on genotype and that extrusion processing may provide an option for preserving biofortified maize products.

Effect of ball milling materials and methods on powder processing of Bi2223 superconductors

NASA Astrophysics Data System (ADS)

Yavuz, M.; Maeda, H.; Vance, L.; Liu, H. K.; Dou, S. X.

1998-10-01

Various milling systems consisting of agate and polypropylene grinding containers, agate and YSZ balls, and dry and wet milling were used in planetary ball-milling and YSZ balls and YSZ container were used in wet and dry attrition milling. The differently milled powders were then evaluated by measurements of particle size, surface area, porosity, size distribution and chemical analysis of the Si, Zr and C contents. The results show that dry milling is much more efficient for particle size reduction in planetary milling than wet milling, whereas wet milling and dry milling gave quite similar results in attrition milling. Meanwhile 0953-2048/11/10/056/img6 contamination was found in powder milled with an agate container with agate balls. Some C contamination from the polypropylene container was detected after milling, but negligible Zr from YSZ balls and C from the grinding carrier (hexane). It was found that after 1 h milling in the planetary mill fracture mechanisms transform from the elastic to the plastic region. Therefore, further milling is not very effective. It was also shown that the Bi2212 phase decomposes into several non-superconducting oxides such as 0953-2048/11/10/056/img7, CuO and a main amorphous phase after extensive dry milling.

Investigation of formation of cut off layers and productivity of screw milling process

NASA Astrophysics Data System (ADS)

Ambrosimov, S. K.; Morozova, A. V.

2018-03-01

The article presents studies of a new method for complex milling surfaces with a screw feed motion. Using the apparatus of algebra of logic, the process of formation of cut metal layers and processing capacity is presented.

Structural and Morphological Evaluation of Nano-Sized MoSi2 Powder Produced by Mechanical Milling

NASA Astrophysics Data System (ADS)

Sameezadeh, Mahmood; Farhangi, Hassan; Emamy, Masoud

Nano-sized intermetallic powders have received great attention owing to their property advantages over conventional micro-sized counterparts. In the present study nano-sized MoSi2 powder has been produced successfully from commercially available MoSi2 (3 μm) by a mechanical milling process carried out for a period of 100 hours. The effects of milling time on size and morphology of the powders were studied by SEM and TEM and image analyzing system. The results indicate that the as-received micrometric powder with a wide size distribution of irregular shaped morphology changes to a narrow size distribution of nearly equiaxed particles with the progress of attrition milling up to 100 h, reaching an average particle size of 71 nm. Structural evolution of milled samples was characterized by XRD to determine the crystallite size and lattice microstrain using Williamson-Hall method. According to the results, the crystallite size of the powders decreases continuously down to 23 nm with increasing milling time up to 100 h and this size refinement is more rapid at the early stages of the milling process. On the other hand, the lattice strain increases considerably with milling up to 65 h and further milling causes no significant changes of lattice strain.

Analyzing the effect of tool edge radius on cutting temperature in micro-milling process

NASA Astrophysics Data System (ADS)

Liang, Y. C.; Yang, K.; Zheng, K. N.; Bai, Q. S.; Chen, W. Q.; Sun, G. Y.

2010-10-01

Cutting heat is one of the important physical subjects in the cutting process. Cutting heat together with cutting temperature produced by the cutting process will directly have effects on the tool wear and the life as well as on the workpiece processing precision and surface quality. The feature size of the workpiece is usually several microns. Thus, the tiny changes of cutting temperature will affect the workpiece on the surface quality and accuracy. Therefore, cutting heat and temperature generated in micro-milling will have significantly different effect than the one in the traditional tools cutting. In this paper, a two-dimensional coupled thermal-mechanical finite element model is adopted to determine thermal fields and cutting temperature during the Micro-milling process, by using software Deform-2D. The effect of tool edge radius on effective stress, effective strain, velocity field and cutting temperature distribution in micro-milling of aluminum alloy Al2024-T6 were investigated and analyzed. Also, the transient cutting temperature distribution was simulated dynamically. The simulation results show that the cutting temperature in Micro-milling is lower than those occurring in conventional milling processes due to the small loads and low cutting velocity. With increase of tool edge radius, the maximum temperature region gradually occurs on the contact region between finished surfaced and flank face of micro-cutter, instead of the rake face or the corner of micro-cutter. And this phenomenon shows an obvious size effect.

Nuclear facility decommissioning and site remedial actions: a selected bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owen, P.T.; Knox, N.P.; Fielden, J.M.

This bibliography contains 693 references with abstracts on the subject of nuclear facility decommissioning, uranium mill tailings management, and site remedial actions. Foreign, as well as domestic, literature of all types - technical reports, progress reports, journal articles, conference papers, symposium proceedings, theses, books, patents, legislation, and research project descriptions - has been included in this publication. The bibliography contains scientific (basic research as well as applied technology), economic, regulatory, and legal literature pertinent to the US Department of Energy's Remedial Action Program. Major chapters are Surplus Facilities Management Program, Nuclear Facilities Decommissioning, Formerly Utilized Sites Remedial Action Program, Uraniummore » Mill Tailings Remedial Action Program, Grand Junction Remedial Action Program, and Uranium Mill Tailings Management. Chapter sections for chapters 1 and 2 include: Design, Planning, and Regulations; Site Surveys; Decontamination Studies; Dismantlement and Demolition; Land Decontamination and Reclamation; Waste Disposal; and General Studies. The references within each chapter are arranged alphabetically by leading author. References having no individual author are arranged by corporate author or by title. Indexes are provided for (1) author; (2) corporate affiliation; (3) title; (4) publication description; (5) geographic location; and (6) keywords. An appendix of 202 bibliographic references without abstracts or indexes has been included in this bibliography. This appendix represents literature identified but not abstracted due to time constraints.« less

NDE investigation of the timber foundation in the historic Kennecott Mine Concentration Mill Building

Treesearch

James P. Wacker; Xiping Wang; Douglas R. Rammer; Bessie M. Woodward

2011-01-01

The U.S. National Park Service acquired the National Historic Copper Mine at Kennecott, Alaska, in 1998. There was uncertainty about the condition of the timber-cribbing foundation supporting the concentration mill, the largest building in the mine complex. A comprehensive on-site evaluation of the timber cribbing foundation was performed in summer 2009. The inspection...

A comparative evaluation of explosion hazards in chemical and mechanical pulp bleaching systems

Treesearch

Peter W. Hart; Alan W. Rudie

2010-01-01

Over the past several years, at least three pulp mills in North America have experienced catastrophic events that resulted in the explosion of pumps, mixers, and tanks. All these mills were using 50% concentration hydrogen peroxide at the site of the explosions. In at least two instances, alkali catalyzed decomposition of peroxide is implicated in the explosion....

42. View of Botany Worsted Mills looking northeast along Sherman ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. View of Botany Worsted Mills looking northeast along Sherman Street; site of 95-97 Dayton Avenue in right distance, at end of Sherman Street - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

Site quality relationships for shortleaf pine

Treesearch

David L. Graney

1986-01-01

Existing information about site quality relationships for shortleaf pine (Pinus echinata Mill.) in the southeastern United States is reviewed in this paper. Estimates of site quality, whether from direct tree measurements or indirect estimates based on soil and site features, are only local observations for many points on the landscape. To be of value to the land...

Health assessment for Cimarron Mining Corporation, Carrizozo, Lincoln County, New Mexico, Region 6. CERCLIS No. NMD980749378. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-05-09

The Cimarron Mining Corporation, an Update 7 National Priorities List site, is located in the southeastern section of Carrizozo, Lincoln County, New Mexico. From 1979 to 1982 the site was operated as a milling operation where precious metals were extracted from crushed iron ore by using either sodium cyanide or potassium cyanide mixed with a metal stripper in a leaching process. Currently the site is inactive; however, drums of sodium/potassium cyanide and solid metal stripping and recovery compounds remain on-site. Preliminary environmental monitoring data indicate chromium, cyanide, lead, and nitrate contamination of on-site groundwater, and cyanide contamination of on-site soil,more » tailings, and wastes. The most likely pathways for contaminant transport to off-site areas appear to be those associated with groundwater and soil. Pathways for human exposure to site-associated contaminants include ingestion of contaminated groundwater and soil and inhalation of contaminated dusts. The site is of potential public health concern because of possible human exposure to site contaminants.« less

Effect of ball milling and heat treatment process on MnBi powders magnetic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Wei; Polikarpov, Evgueni; Choi, Jung-Pyung

The metallic compound MnBi has high intrinsic coercivity with large positive temperature coefficient. The coercivity of MnBi exceeds 12 kOe and 26 kOe at 300 K and 523 K, respectively. Hence MnBi is a good candidate for the hard phase in exchange coupled nanocomposite magnets. In order to maximize the loading of the soft phase, the size of the MnBi particle has to be close to 500 nm, the size of single magnetic domain. Low energy milling is the common method to reduce MnBi particle size. However, only 3-7 mu m size particle can be achieved without significant decomposition. Here,more » we report our effort on preparing submicron MnBi powders using traditional powder metallurgy methods. Mn55Bi45 magnetic powders were prepared using arc melting method, followed by a series of thermal-mechanical treatment to improve purity, and finished with low energy ball milling at cryogenic temperature to achieve submicron particle size. The Mn55Bi45 powders were decomposed during ball milling process and recovered during 24 h 290 degrees C annealing process. With increasing ball-milling time, the saturation magnetization of MnBi decreases, while the coercivity increases. Annealing after ball milling recovers some of the magnetization, indicating the decomposition occurred during the ball-milling process can be reversed. The coercivity of Mn55Bi45 powders are also improved as a result of the heat treatment at 290 degrees C for 24 h. The world record magnetization 71.2 emu/g measured applying a field of 23 kOe has been achieved via low energy ball mill at room temperature« less

Application of dragonfly algorithm for optimal performance analysis of process parameters in turn-mill operations- A case study

NASA Astrophysics Data System (ADS)

Vikram, K. Arun; Ratnam, Ch; Lakshmi, VVK; Kumar, A. Sunny; Ramakanth, RT

2018-02-01

Meta-heuristic multi-response optimization methods are widely in use to solve multi-objective problems to obtain Pareto optimal solutions during optimization. This work focuses on optimal multi-response evaluation of process parameters in generating responses like surface roughness (Ra), surface hardness (H) and tool vibration displacement amplitude (Vib) while performing operations like tangential and orthogonal turn-mill processes on A-axis Computer Numerical Control vertical milling center. Process parameters like tool speed, feed rate and depth of cut are considered as process parameters machined over brass material under dry condition with high speed steel end milling cutters using Taguchi design of experiments (DOE). Meta-heuristic like Dragonfly algorithm is used to optimize the multi-objectives like ‘Ra’, ‘H’ and ‘Vib’ to identify the optimal multi-response process parameters combination. Later, the results thus obtained from multi-objective dragonfly algorithm (MODA) are compared with another multi-response optimization technique Viz. Grey relational analysis (GRA).

Time-Integrated Monitoring of Dioxin-Like Polychlorinated Biphenyls (dl-PCBs) in Aquatic Environments using the Ceramic Toximeter and the CALUX Bioassay

PubMed Central

Addeck, Amr; Croes, Kim; Van Langenhove, Kersten; Denison, Michael S.; Afify, Ahmed S.; Gao, Yue; Elskens, Marc; Baeyens, Willy

2015-01-01

Ceramic passive samplers or toximeters (packed with active carbon 1% w/w on celite), in combination with the CALUX bioassay have been used as a time-integrated monitoring technique for dissolved dioxin-like PCBs in urban and industrial wastewaters. The technique showed to be reliable during laboratory experiments: (1) PCB-126 amounts extracted from the passive samplers increased linearly with the time of exposure and (2) PCB-126 concentrations calculated from the amounts accumulated by the passive samplers were in agreement with their concentrations in the testing solution. Afterwards the toximeters were applied in the field. Two sampling sites located in Egypt were chosen: the Belbeis drainage canal, and the EMAK paper mill. A total of 18 ceramic toximeters were exposed to the wastewater in both sampling sites for a maximum period of 4 weeks. Two samplers were collected weekly from each site to monitor the increase in target analytes over time. Extracts were analyzed using the CALUX bioassay and the total dioxin-like PCB toxicity was reported for the aqueous phase (water column), as well as the solid phase (sediment and sludge) in both sampling sites. The time-weighted average concentration (TWA) of dl-PCBs in wastewater of the paper mill during the sampling period ranged between 7.1 and 9.1 pg-BEQ L-1, while that of the drainage canal ranged between 9.5 and 12.2 pg-BEQ L-1. The dl-PCBs in the fibrous sludge (paper mill) and bottom sediment (drainage canal) were 0.5 and 0.4 pg-BEQ g-1 dry-weight, respectively. The organic-carbon normalized partition coefficients between sediment and water (log Koc) for the paper mill and the canal were 2.4 and 4.3, respectively. PMID:24468390

Optimization and cost estimation of novel wheat biorefining for continuous production of fermentation feedstock.

PubMed

Arifeen, Najmul; Wang, Ruohang; Kookos, Ioannis; Webb, Colin; Koutinas, Apostolis A

2007-01-01

A wheat-based continuous process for the production of a nutrient-complete feedstock for bioethanol production by yeast fermentation has been cost-optimized. This process could substitute for the current wheat dry milling process employed in industry for bioethanol production. Each major wheat component (bran, gluten, starch) is extracted and processed for different end-uses. The separate stages, liquefaction and saccharification, used currently in industry for starch hydrolysis have been integrated into a simplified continuous process by exploiting the complex enzymatic consortium produced by on-site fungal bioconversions. A process producing 120 m3 h-1 nutrient-complete feedstock for bioethanol production containing 250 g L-1 glucose and 0.85 g L-1 free amino nitrogen would result in a production cost of $0.126/kg glucose.

Response of imperiled Okaloosa darters to stream restoration

USGS Publications Warehouse

Reeves, David B.; Tate, William B.; Jelks, Howard L.; Jordan, Frank

2016-01-01

The Okaloosa Darter Etheostoma okaloosae is a small percid endemic to six stream drainages in northwestern Florida. The U.S. Fish and Wildlife Service listed Okaloosa Darters as endangered in 1973 and downlisted them to threatened in 2011 because of habitat improvements and increasing abundance across much of their geographic range. Delisting is possible if remaining recovery criteria are met, including restoration of degraded stream reaches. Impounded reaches of Anderson Branch, Mill Creek, and Toms Creek were restored by removing impediments to water flow, draining impoundments, and reconstructing stream reaches. Restorations of Anderson Branch and Mill Creek were designed to rehabilitate populations of Okaloosa Darters without significantly affecting popular recreational activities at these locations. Restorations were evaluated from 2007 to 2013 by comparing counts of Okaloosa Darters and the composition of microhabitats in restored and nearby undisturbed reference sites. Okaloosa Darters were absent from degraded stream reaches at the beginning of the study, but they rapidly colonized once restorations were completed. Counts of Okaloosa Darters in reference and restoration sites in Anderson Branch were similar by the end of the study, whereas counts in restoration sites were significantly lower than nearby reference sites in Mill and Toms creeks. Restoration sites tended to have lower coverage of sand and root and higher coverage of macrophytes. As riparian vegetation surrounding restoration sites matures to a closed canopy that reduces excessive growth of macrophytes, stream microhabitats and numbers of darters will probably become similar to reference sites. Restoration of degraded stream sites increased abundance and distribution of Okaloosa Darters and reconnected formerly isolated upstream and downstream populations. These projects demonstrated that restoration is a useful conservation tool for imperiled fishes such as Okaloosa Darters and can be undertaken without interfering with popular recreational activities.

High-conversion hydrolysates and corn sweetener production in dry-grind corn process.

USDA-ARS?s Scientific Manuscript database

Most corn is processed to fuel ethanol and distillers’ grain animal feed using the dry grind process. However, wet milling is needed to refine corn starch. Corn starch is in turn processed to numerous products, including glucose and syrup. However, wet milling is a capital, labor, and energy intensi...

Feasibility investigations on multi-cutter milling process: A novel fabrication method for microreactors with multiple microchannels

NASA Astrophysics Data System (ADS)

Pan, Minqiang; Zeng, Dehuai; Tang, Yong

A novel multi-cutter milling process for multiple parallel microchannels with manifolds is proposed to address the challenge of mass manufacture as required for cost-effective commercial applications. Several slotting cutters are stacked together to form a composite tool for machining microchannels simultaneously. The feasibility of this new fabrication process is experimentally investigated under different machining conditions and reaction characteristics of methanol steam reforming for hydrogen production. The influences of cutting parameters and the composite tool on the microchannel qualities and burr formation are analyzed. Experimental results indicate that larger cutting speed, smaller feed rate and cutting depth are in favor of obtaining relatively good microchannel qualities and small burrs. Of all the cutting parameters considered in these experiments, 94.2 m min -1 cutting speed, 23.5 mm min -1 feed rate and 0.5 mm cutting depth are found to be the optimum value. According to the comparisons of experimental results of multi-cutter milling process and estimated one of other alternative methods, it is found that multi-cutter milling process shows much shorter machining time and higher work removal rate than that of other alternative methods. Reaction characteristics of methanol steam reforming in microchannels also indicate that multi-cutter milling process is probably suitable for a commercial application.

Efficient production of nanoparticle-loaded orodispersible films by process integration in a stirred media mill.

PubMed

Steiner, Denise; Finke, Jan Henrik; Kwade, Arno

2016-09-25

Orodispersible films possess a great potential as a versatile platform for nanoparticle-loaded oral dosage forms. In this case, poorly water-soluble organic materials were ground in a stirred media mill and embedded into a polymer matrix. The aim of this study was the shortening of this manufacturing process by the integration of several process steps into a stirred media mill without facing disadvantages regarding the film quality. Furthermore, this process integration is time conserving due to the high stress intensities provided in the mill and applicable for high solids contents and high suspension viscosities. Two organic materials, the model compound Anthraquinone and the active pharmaceutical ingredient Naproxen were investigated in this study. Besides the impact of the film processing on the crystallinity of the particles in the orodispersible film, a particle load of up to 50% was investigated with the new developed processing route. Additionally, a disintegration test was developed, combining an appropriate amount of saliva substitute and a clear endpoint determination. In summary, high nanoparticle loads in orodispersible films with good particle size preservation after film redispersion in water as well as a manufacturing of the film casting mass within a few minutes in a stirred media mill was achieved. Copyright © 2016 Elsevier B.V. All rights reserved.

10. DETAILED VIEW OF THE EAST ELEVATION. THE UPPER SET ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. DETAILED VIEW OF THE EAST ELEVATION. THE UPPER SET OF WINDOWS PROVIDE LIGHT FOR THE DELIVERY LEVEL. THE LOWER SETS OF WINDOWS PROVIDE LIGHT TO THREE STORY SPACE BENEATH THE DELIVERY LEVEL AND BEHIND THE ORE STORAGE BINS. NOTE THE ORE DELIVER TRESTLE AT THE TIME THE PHOTOGRAPH WAS TAKEN, THE MODERN CEMENT MIXER AND WHEELBARROWS WERE FOR THIS WORK. NOTE THE MORTAR BOXES ON THEIR SIDES. IT IS UNCLEAR IF THESE WERE FROM EARLIER STAMPS AT THIS MILL OR IF THEY WERE BROUGHT TO THE SITE FROM OTHER MILLS IN THE REGION. RISDON IRON WORKS IS CAST INTO THE MORTARS AND THEY ALSO BEAR A PLATE: WHITE, ROGERS AND CO. MILL WRIGHTS. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Point Defects in Quenched and Mechanically-Milled Intermetallic Compounds

NASA Astrophysics Data System (ADS)

Sinha, Praveen

Investigations were made of structural and thermal point defects in the highly-ordered B2 compound PdIn and deformation-induced defects in PdIn and NiAl. The defects were detected through the quadrupole interactions they induce at nearby ^{111}In/Cd probe atoms using the technique of perturbed gamma-gamma angular correlations (PAC). Measurements on annealed PdIn on both sides of stoichiometry show structural defects that are the Pd vacancies on the Pd-poor side of the stoichiometry and Pd antisite atoms on the Pd-rich side. Signals were attributed to various defect configurations near the In/Cd probes. In addition to the first-shell Pd vacancy and second-shell Pd antisite atom configurations previously observed by Hahn and Muller, we observed two Pd-divacancy configurations in the first shell, a fourth-shell Pd vacancy, a second-shell In vacancy and the combination of a first -shell Pd vacancy and fourth-shell Pd vacancy. Vacancies on both the Pd and In sublattices were detected after quenching. Fractions of probe atoms having each type of neighboring vacancy defect were observed to increase monotonically with quenching temperature over the range 825-1500 K. For compositions very close to 50.15 at.% Pd, nearly equal site fractions were observed for Pd and In vacancies, indicating that the Schottky vacancy-pair defect is the thermal defect at high temperature. The formation enthalpy of the Schottky defect was determined from measurements of the Pd-vacancy site fraction to be 1.30(18) eV from analysis of quenching data in the range 825-1200 K, using the law of mass action and assuming a random distribution. Above 1200 K, the Pd-vacancy concentration was observed to be saturated at a value of 1.3(2) atomic percent. For more Pd-rich compositions, evidence was also obtained for a defect reaction in which a Pd antisite atom and Pd vacancy react to form an In vacancy, thereby increasing the In vacancy concentration and decreasing the Pd vacancy concentration. Analysis of defect concentrations allowed the conclusion that the In vacancy signal was due to second-shell and not third-shell defects. PAC spectroscopy was applied to study deformation -induced defects in PdIn and NiAl after mechanically milling in a SPEX 8000 vibrator mill for periods of up to four hours. For PdIn, the Pd vacancy concentration increased rapidly for short milling times and was observed to saturate at a value of 3.5(5) at.% after 10 minutes of milling when milling was carried out using a WC vial to avoid sample contamination. Such a large vacancy concentration accounts for 4.41(63) kJ mol-1 excess-stored energy in milled PdIn and implies a high density of "broken bonds" which may lead to mechanical instability of the lattice. Milling also produced In antisite atoms on the Pd sublattice. The antisite-atom concentration increased linearly with milling time, reaching a value of 4.0(7) at.% after 2 hours of milling. The Ni vacancy concentration in NiAl was also observed to increase with milling and to saturate after two hours of milling. Here, the "local" Ni vacancy concentration in the first-neighbor shell of the probe, deduced from the vacancy site fraction, was in excess of values that should occur if defects were located at random. This is attributed to binding between the Ni vacancy and the In/Cd probe, which is known from other work to be 0.22 eV.

Hot mill process parameters impacting on hot mill tertiary scale formation

NASA Astrophysics Data System (ADS)

Kennedy, Jonathan Ian

For high end steel applications surface quality is paramount to deliver a suitable product. A major cause of surface quality issues is from the formation of tertiary scale. The scale formation depends on numerous factors such as thermo-mechanical processing routes, chemical composition, thickness and rolls used. This thesis utilises a collection of data mining techniques to better understand the influence of Hot Mill process parameters on scale formation at Port Talbot Hot Strip Mill in South Wales. The dataset to which these data mining techniques were applied was carefully chosen to reduce process variation. There are several main factors that were considered to minimise this variability including time period, grade and gauge investigated. The following data mining techniques were chosen to investigate this dataset: Partial Least Squares (PLS); Logit Analysis; Principle Component Analysis (PCA); Multinomial Logistical Regression (MLR); Adaptive Neuro Inference Fuzzy Systems (ANFIS). The analysis indicated that the most significant variable for scale formation is the temperature entering the finishing mill. If the temperature is controlled on entering the finishing mill scale will not be formed. Values greater than 1070 °C for the average Roughing Mill and above 1050 °C for the average Crop Shear temperature are considered high, with values greater than this increasing the chance of scale formation. As the temperature increases more scale suppression measures are required to limit scale formation, with high temperatures more likely to generate a greater amount of scale even with fully functional scale suppression systems in place. Chemistry is also a significant factor in scale formation, with Phosphorus being the most significant of the chemistry variables. It is recommended that the chemistry specification for Phosphorus be limited to a maximum value of 0.015 % rather than 0.020 % to limit scale formation. Slabs with higher values should be treated with particular care when being processed through the Hot Mill to limit scale formation.

The SHOLO mill: return on investment versus mill design

Treesearch

Hugh W. Reynolds; Charles J. Gatchell; Charles J. Gatchell

1971-01-01

The newly developed SHOLO (from SHOrt Log) process can be used to convert low-grade hardwood logs into parts for standard warehouse pallets and pulp chips. Should you build a SHOLO mill? This paper has been prepared to help you decide.

Performance of Color Camera Machine Vision in Automated Furniture Rough Mill Systems

Treesearch

D. Earl Kline; Agus Widoyoko; Janice K. Wiedenbeck; Philip A. Araman

1998-01-01

The objective of this study was to evaluate the performance of color camera machine vision for lumber processing in a furniture rough mill. The study used 134 red oak boards to compare the performance of automated gang-rip-first rough mill yield based on a prototype color camera lumber inspection system developed at Virginia Tech with both estimated optimum rough mill...

An exploratory investigation of polar organic compounds in waters from a lead–zinc mine and mill complex

USGS Publications Warehouse

Rostad, Colleen E.; Schmitt, Christopher J.; Schumacher, John G.; Leiker, Thomas J.

2011-01-01

Surface water samples were collected in 2006 from a lead mine-mill complex in Missouri to investigate possible organic compounds coming from the milling process. Water samples contained relatively high concentrations of dissolved organic carbon (DOC; greater than 20 mg/l) for surface waters but were colorless, implying a lack of naturally occurring aquatic humic or fulvic acids. Samples were extracted by three different types of solid-phase extraction and analyzed by electrospray ionization/mass spectrometry. Because large amounts of xanthate complexation reagents are used in the milling process, techniques were developed to extract and analyze for sodium isopropyl xanthate and sodium ethyl xanthate. Although these xanthate reagents were not found, trace amounts of the degradates, isopropyl xanthyl thiosulfonate and isopropyl xanthyl sulfonate, were found in most locations sampled, including the tailings pond downstream. Dioctyl sulfosuccinate, a surfactant and process filtering aid, was found at concentrations estimated at 350 μg/l at one mill outlet, but not downstream. Release of these organic compounds downstream from lead-zinc mine and milling areas has not previously been reported. A majority of the DOC remains unidentified.

A post-processing study on aluminum surface by fiber laser: Removing face milling patterns

NASA Astrophysics Data System (ADS)

Kayahan, Ersin

2018-05-01

The face milling process of the metal surface is a well-known machining process of using rotary cutters to remove material from a workpiece. Flat metal surfaces can be produced by a face milling process. However, in practice, visible, traced marks following the motion of points on the cutter's face are usually apparent. In this study, it was shown that milled patterns can be removed by means of 20 W fiber laser on the aluminum surface (AA7075). Experimental results also showed that roughened and hydrophobic surface can be produced with optimized laser parameters. It is a new approach to remove the patterns from the metal surface and can be explained through roughening by re-melting instead of ablation. The new method is a strong candidate to replace sandblasting the metal surface. It is also cheap and environmentally friendly.

An argon ion beam milling process for native AlOx layers enabling coherent superconducting contacts

NASA Astrophysics Data System (ADS)

Grünhaupt, Lukas; von Lüpke, Uwe; Gusenkova, Daria; Skacel, Sebastian T.; Maleeva, Nataliya; Schlör, Steffen; Bilmes, Alexander; Rotzinger, Hannes; Ustinov, Alexey V.; Weides, Martin; Pop, Ioan M.

2017-08-01

We present an argon ion beam milling process to remove the native oxide layer forming on aluminum thin films due to their exposure to atmosphere in between lithographic steps. Our cleaning process is readily integrable with conventional fabrication of Josephson junction quantum circuits. From measurements of the internal quality factors of superconducting microwave resonators with and without contacts, we place an upper bound on the residual resistance of an ion beam milled contact of 50 mΩ μm2 at a frequency of 4.5 GHz. Resonators for which only 6% of the total foot-print was exposed to the ion beam milling, in areas of low electric and high magnetic fields, showed quality factors above 106 in the single photon regime, and no degradation compared to single layer samples. We believe these results will enable the development of increasingly complex superconducting circuits for quantum information processing.

Synthesis and magnetization studies of nanopowder Fe₇₀Ni₂₀Cr₁₀ alloys prepared by high energy milling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chater, R., E-mail: chatersamy@yahoo.fr; Bououdina, M., E-mail: mboudina@gmail.com; Department of Physics, College of Science, University of Bahrain, PO Box 32038, Kingdom of Bahrain

2013-05-01

Nanocrystalline Fe{sub 1–x–y}Ni xCr y (x=20, y=10% in Wt)) alloy samples were prepared by mechanical alloying process. Fe, Ni and Cr elemental powders have been ball milled in a planetary mill for various periods of time, up to 27 h. XRD analysis allowed the determination of the structure of the mixture, the average crystallite size and the lattice parameter as a function of milling time. The complete formation of FeNiCr is observed after 27 h milling. With increasing milling time from 0 to 27 h, it is observed that the lattice parameter increases from 0.3515 to 0.3593 nm as wellmore » as an increase of microstrain from 0.15 to 0.40%, whereas the grain size decreases from 48 to 13 nm. Grain morphology of the powders at different formation stages was examined using SEM. Saturation magnetization and coercive fields derived from the hysteresis curves are discussed as a function of milling time. - Graphical abstract: Fe₇₀Ni₂₀Cr₁₀ nanopowders were prepared using a planetary ball mill. The structure and microstructure vary with milling time; thereby important modifications of the magnetic properties were observed and discussed. Highlights: • Nanocrystalline Fe₇₀Ni₂₀Cr₁₀ alloy were prepared by the mechanical alloying process. • The complete formation of Fe₇₀Ni₂₀Cr₁₀ is observed after 24 h milling. • With increasing milling time, the grain size decreases, while the strain increases. • The SEM images allowed following the morphology of the materials at different stages. • M s and H C derived from the hysteresis are discussed as a function of milling time.« less

An improved FIB sample preparation technique for site-specific plan-view specimens: A new cutting geometry.

PubMed

Li, Chen; Habler, Gerlinde; Baldwin, Lisa C; Abart, Rainer

2018-01-01

Focused ion beam (FIB) sample preparation technique in plan-view geometry allows direct correlations of the atomic structure study via transmission electron microscopy with micrometer-scale property measurements. However, one main technical difficulty is that a large amount of material must be removed underneath the specimen. Furthermore, directly monitoring the milling process is difficult unless very large material volumes surrounding the TEM specimen site are removed. In this paper, a new cutting geometry is introduced for FIB lift-out sample preparation with plan-view geometry. Firstly, an "isolated" cuboid shaped specimen is cut out, leaving a "bridge" connecting it with the bulk material. Subsequently the two long sides of the "isolated" cuboid are wedged, forming a triangular prism shape. A micromanipulator needle is used for in-situ transfer of the specimen to a FIB TEM grid, which has been mounted parallel with the specimen surface using a simple custom-made sample slit. Finally, the grid is transferred to the standard FIB grid holder for final thinning with standard procedures. This new cutting geometry provides clear viewing angles for monitoring the milling process, which solves the difficulty of judging whether the specimen has been entirely detached from the bulk material, with the least possible damage to the surrounding materials. With an improved success rate and efficiency, this plan-view FIB lift-out specimen preparation technique should have a wide application for material science. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Synchrotron X-ray characterization of mackinawite and uraninite relevant to bio-remediation of groundwater contaminated with uranium

NASA Astrophysics Data System (ADS)

Carpenter, J.; Hyun, S.; Hayes, K. F.

2010-12-01

Uranium (U) originating from mining operations for weapon manufacturing and nuclear energy production is a significant radionuclide contaminant in groundwater local to uranium mining, uranium milling, and uranium mill tailing (UMT) storage sites. In the USA, the Department of Energy (DOE) is currently overseeing approximately 24 Uranium Mill Tailing Remediation Action (UMTRA) sites which have collectively processed over 27 million tons of uranium ore1,2. In-Situ microbial bio-reduction of the highly mobile U6+ ion into the dramatically less mobile U4+ ion has been demonstrated as an effective remedial process to inhibit uranium migration in the aqueous phase3. The resistance of this process to oxidization and possible remobilization of U when bioremediation stops (and oxidants such as oxygen from the air or nitrate in water diffuse into the formation) in the long term is not known. UMTRA site studies3 have shown that iron sulfide solids are produced by sulfate reducing bacteria (SRB) during U bioremediation, and some forms of these iron sulfide solids are known to be effective oxidant scavengers, potentially protecting against re-oxidation and thus remobilization of U. This work is investigating the role of iron sulfide solids in the long-term immobilization of reduced U compounds after bioremediation is completed in groundwater local to UMTRA sites. Re-oxidation tests are being performed in packed media columns loaded with both FeS and U solids. High quality mackinawite (FeS), and uraninite (UO2) have been synthesized in our laboratory via a wet chemistry approach. These synthetic materials are expected to mimic the naturally occurring and biogenic materials present in biologically stimulated UMTRA sites. In order to establish the initial conditions of the prepared experimental columns and to compare synthetic and biogenic FeS and UO2, these synthesized materials have been characterized with synchrotron radiation at the Stanford Synchrotron Radiation Lightsource using synchrotron x-ray powder diffraction (SXRD) and extended x-ray absorption fine structure (EXAFS). SXRD data were collected and analyzed with profile fitting to determine lattice parameters and crystallite size for comparison with published values for both biogenic and synthetic materials. This is particularly of interest for UO2, as there is very little information on particle size and lattice parameters for synthetic UO2 in the literature. Profile fitting of the SXRD data for FeS gives lattice parameters of a = b = 3.668 and a mean crystallite size of 5 to 8 nm. Both of these values are in good agreement with published values. For fresh UO2, lattice parameters were determined as a = b = c = 5.4 nm for both freshly synthesized and aged (3 months) UO2 and particle size was determined to be 3.5 nm for fresh UO2 and 5.83 nm for aged UO2. This suggests a growth mechanism for crystallites over time, and an inferred decrease in reactivity.

Productivity and cost analysis of a mobile pyrolysis system deployed to convert mill residues into biochar

Treesearch

Woodam Chung; Dongyeob Kim; Nathaniel Anderson

2012-01-01

Forest and mill residues are a promising source of biomass feedstock for the production of bioenergy, biofuels and bioproducts. However, high costs of transportation and handling of feedstock often make utilization of forest residues, such as logging slash, financially unviable. As a result, these materials are often considered waste and left on site to decompose or...

The genetics of shortleaf pine (Pinus echinata mill.) with implications for restoration and management

Treesearch

John F. Stewart; Rodney E. Will; Barbara S. Crane; C. Dana Nelson

2016-01-01

Shortleaf pine (Pinus echinata Mill.) is an important commercial timber resource and forest ecosystem component in the southeastern USA. The species occurs in mainly drier sites as an early- to mid-successional species, is fireadapted, and it plays an important role in the fire ecology of the region. However, shortleaf pine genetics are not well-studied, especially in...

Remedial action plan and site design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-02-01

This volume contains appendices D6 through D8 containing laboratory test data: from MK-F investigation, 1987, Old Rifle and New Rifle sites; on bentonite amended radon barrier material; and from MK-F investigation, 1987, riprap tests.

SITE BULLETIN, ATTENUATED ANAEROBIC DECHLORINATION OF GROUNDWATER USING HRC MACTEC - HARDING ESE

EPA Science Inventory

A SITE demonstration of the Harding ESE permeable reactive barrier wall (PRBW) was conducted on the contaminated groundwater from the Fisherville Mill site in Grafton, MA beginning June 2000 to July 2003. Installation of the PRBW was accomplished by injecting HRC into a series of...

Longleaf pine site zones

Treesearch

Phillip J. Craul; John S. Kush; William D. Boyer

2005-01-01

The authors delineate six major climatic areas of the longleaf pine (Pinus palustris Mill.) region. They subdivide these areas into 21 site zones, each of which is deemed homogenous with respect to climate, physiography, and soils. The site zones are mapped and their climate, physiography, and soils described. The authors recommend that plantings of...

An environmentally friendly ball milling process for recovery of valuable metals from e-waste scraps.

PubMed

Zhang, Zhi-Yuan; Zhang, Fu-Shen; Yao, TianQi

2017-10-01

The present study reports a mechanochemical (MC) process for effective recovery of copper (Cu) and precious metals (i.e. Pd and Ag) from e-waste scraps. Results indicated that the mixture of K 2 S 2 O 8 and NaCl (abbreviated as K 2 S 2 O 8 /NaCl hereafter) was the most effective co-milling reagents in terms of high recovery rate. After co-milling with K 2 S 2 O 8 /NaCl, soluble metallic compounds were produced and consequently benefit the subsequent leaching process. 99.9% of Cu and 95.5% of Pd in the e-waste particles could be recovered in 0.5mol/L diluted HCl in 15min. Ag was concentrated in the leaching residue as AgCl and then recovered in 1mol/L NH 3 solution. XRD and XPS analysis indicated that elemental metals in the raw materials were transformed into their corresponding oxidation state during ball milling process at low temperature, implying that solid-solid phase reactions is the reaction mechanism. Based on the results and thermodynamic parameters of the probable reactions, possible reaction pathways during ball milling were proposed. Suggestion on category of e-waste for ball milling process was put forward according to the experiment results. The designed metal recovery process of this study has the advantages of highly recovery rate and quick leaching speed. Thus, this study offers a promising and environmentally friendly method for recovering valuable metals from e-waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

Site remediation using photocatalytic VOC destruction of chlorinated hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brunet, R.A.H.; Pearcey, R.; Kittrell, J.R.

1999-07-01

An innovative environmental technology has been developed and demonstrated for cost-effective control of toxic air emissions, such as trichloroethylene (TCE) and perchloroethylene (PCE), found in soil and groundwater at hazardous waste sites and in industrial effluents. The technology uses UV light and a proprietary photocatalyst to adsorb and destroy pollutants at ambient conditions, even with high humidity. Air stripping and soil vapor extraction efficiently transfer the pollutants to the gas phase, where they can be economically treated by photocatalysis without the risk of hazardous by-product formation. The AIR2000 photocatalytic technology was successfully installed at the Stamina Mills Superfund site inmore » Rhode Island, where a commercial scale unit is treating 700 cfm of up to 1,000 ppm TCE, mixed with PCE, dichloroethylene (DCE), trichloroethane (TCA), and vinyl chloride (VC) produced through a combination of soil vapor extraction (SVE) and air stripping. As part of the EPA SITE program, the system was monitored for overall destruction removal efficiency (DRE) and hazardous by-product formation. A DRE in excess of 99% was reported over the first four months of operation, with greater than 99.99% DRE achieved, without production of hazardous by-products. The operating cost of the system is approximately 20% of activated carbon adsorption, which provides approximately $1,500,000 in cost savings over the life of the Stamina Mills project. The Adsorption Integrated Reaction (AIR) process is the recipient of the 1997 SBIR Technology of the Year award, the 1998 EPA Environmental Technology Innovator Award, and the 1998 R and D 100 Award.« less

Site index model for naturally regenerated even-aged longleaf pine

Treesearch

Dwight K. Lauer; John S. Kush

2013-01-01

Data from the Regional Longleaf Growth Study (339 permanent sample plots) were used to develop a site index model for naturally regenerated, even-aged longleaf pine (Pinus palustris Mill.). The site index equation was derived using the generalized algebraic difference approach and is base-age invariant. Using height as a measure of site productivity...

Nano-sized crystalline drug production by milling technology.

PubMed

Moribe, Kunikazu; Ueda, Keisuke; Limwikrant, Waree; Higashi, Kenjirou; Yamamoto, Keiji

2013-01-01

Nano-formulation of poorly water-soluble drugs has been developed to enhance drug dissolution. In this review, we introduce nano-milling technology described in recently published papers. Factors affecting the size of drug crystals are compared based on the preparation methods and drug and excipient types. A top-down approach using the comminution process is a method conventionally used to prepare crystalline drug nanoparticles. Wet milling using media is well studied and several wet-milled drug formulations are now on the market. Several trials on drug nanosuspension preparation using different apparatuses, materials, and conditions have been reported. Wet milling using a high-pressure homogenizer is another alternative to preparing production-scale drug nanosuspensions. Dry milling is a simple method of preparing a solid-state drug nano-formulation. The effect of size on the dissolution of a drug from nanoparticles is an area of fundamental research, but it is sometimes incorrectly evaluated. Here, we discuss evaluation procedures and the associated problems. Lastly, the importance of quality control, process optimization, and physicochemical characterization are briefly discussed.

Experimental Study in Taguchi Method on Surface Quality Predication of HSM

NASA Astrophysics Data System (ADS)

Ji, Yan; Li, Yueen

2018-05-01

Based on the study of ball milling mechanism and machining surface formation mechanism, the formation of high speed ball-end milling surface is a time-varying and cumulative Thermos-mechanical coupling process. The nature of this problem is that the uneven stress field and temperature field affect the machined surface Process, the performance of the processing parameters in the processing interaction in the elastic-plastic materials produced by the elastic recovery and plastic deformation. The surface quality of machining surface is characterized by multivariable nonlinear system. It is still an indispensable and effective method to study the surface quality of high speed ball milling by experiments.

Distribution of selected volatile organic compounds determined with water-to-vapor diffusion samplers at the interface between ground water and surface water, Centredale Manor site, North Providence, Rhode Island, September 1999

USGS Publications Warehouse

Church, Peter E.; Lyford, Forest P.; Clifford, Scott

2000-01-01

Volatile organic compounds are present in soils and ground water at the Centredale Manor Superfund Site in North Providence, Rhode Island. In September 1999, water-to-vapor diffusion samplers were placed in the bottom sediments of waterways adjacent to the site to identify possible contaminated ground-water discharge areas. The approximate12-acre site is a narrow stretch of land between the eastern bank of the Woonasquatucket River, downstream from the U.S. Route 44 bridge and a former mill raceway. The samplers were placed along a 2,250-foot reach of the Woonasquatucket River, in the former mill raceway several hundred feet to the east and parallel to the river, and in a cross channel between the river and former mill raceway. Volatile organic compounds were detected in 84 of the 104 water-to-vapor diffusion samplers retrieved. Trichloroethylene and tetrachloro-ethylene were the principal volatile organic compounds detected. The highest vapor concentrations measured for these two chemicals were from diffusion samplers located along an approximate 100-foot reach of the Woonasquatucket River about 500 feet downstream of the bridge; here trichloroethylene and tetrachloroethylene vapor concentrations ranged from about 2,000 to 180,000 and 1,600 to 1,400,000 parts per billion by volume, respectively. Upstream and downstream from this reach and along the former mill raceway, trichloroethylene and tetrachloroethylene vapor concentrations from the diffusion samples were generally less than 100 parts per billion by volume. Along the lower reaches of the river and mill raceway, however, and in the cross channel, vapor concentrations of trichloroethylene exceeded 100 parts per billion by volume and tetrachloroethylene exceeded 1,000 parts per billion by volume in several diffusion samples. Although diffusion sample vapor concentrations are higher than water concentrations in surface waters and in ground water, and they should only be interpreted qualitatively as relative values, these values provide important information as to potential discharge areas of contaminants.

Energy Efficiency Feasibility Study and Resulting Plan for the Bay Mills Indian Community

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kushman, Chris

In 2011 the Inter-Tribal Council of Michigan, Inc. was awarded an Energy Efficiency Development and Deployment in Indian Country grant from the U.S. Department of Energy’s Tribal Energy Program. This grant aimed to study select Bay Mills Indian Community community/government buildings to determine what is required to reduce each building’s energy consumption by 30%. The Bay Mills Indian Community (BMIC) buildings with the largest expected energy use were selected for this study and included the Bay Mills Ellen Marshall Health Center building, Bay Mills Indian Community Administration Building, Bay Mills Community College main campus, Bay Mills Charter School and themore » Waishkey Community Center buildings. These five sites are the largest energy consuming Community buildings and comprised the study area of this project titled “Energy Efficiency Feasibility Study and Resulting Plan for the Bay Mills Indian Community”. The end objective of this study, plan and the Tribe is to reduce the energy consumption at the Community’s most energy intensive buildings that will, in turn, reduce emissions at the source of energy production, reduce energy expenditures, create long lasting energy conscious practices and positively affect the quality of the natural environment. This project’s feasibility study and resulting plan is intended to act as a guide to the Community’s first step towards planned energy management within its buildings/facilities. It aims to reduce energy consumption by 30% or greater within the subject facilities with an emphasis on energy conservation and efficiency. The energy audits and related power consumption analyses conducted for this study revealed numerous significant energy conservation and efficiency opportunities for all of the subject sites/buildings. In addition, many of the energy conservation measures require no cost and serve to help balance other measures requiring capital investment. Reoccurring deficiencies relating to heating, cooling, thermostat setting inefficiencies, powering computers, lighting, items linked to weatherization and numerous other items were encountered that can be mitigated with the energy conservation measures developed and specified during the course of this project.« less

Surface complexation modeling of U(VI) adsorption by aquifer sediments from a former mill tailings site at Rifle, Colorado

USGS Publications Warehouse

Hyun, S.P.; Fox, P.M.; Davis, J.A.; Campbell, K.M.; Hayes, K.F.; Long, P.E.

2009-01-01

A study of U(VI) adsorption by aquifer sediment samples from a former uranium mill tailings site at Rifle, Colorado, was conducted under oxic conditions as a function of pH, U(VI), Ca, and dissolved carbonate concentration. Batch adsorption experiments were performed using <2mm size sediment fractions, a sand-sized fraction, and artificial groundwater solutions prepared to simulate the field groundwater composition. To encompass the geochemical conditions of the alluvial aquifer at the site, the experimental conditions ranged from 6.8 ?? 10-8 to 10-5 M in [U(VI)]tot, 7.2 to 8.0 in pH, 3.0 ?? 10-3 to 6.0 ?? 10 -3 M in [Ca2+], and 0.05 to 2.6% in partial pressure of carbon dioxide. Surface area normalized U(VI) adsorption Kd values for the sand and <2 mm sediment fraction were similar, suggesting a similar reactive surface coating on both fractions. A two-site two-reaction, nonelectrostatic generalized composite surface complexation model was developed and successfully simulated the U(VI) adsorption data. The model successfully predicted U(VI) adsorption observed from a multilevel sampling well installed at the site. A comparison of the model with the one developed previously for a uranium mill tailings site at Naturita, Colorado, indicated that possible calcite nonequilibrium of dissolved calcium concentration should be evaluated. The modeling results also illustrate the importance of the range of data used in deriving the best fit model parameters. ?? 2009 American Chemical Society.

Nuclear facility decommissioning and site remedial actions: A selected bibliography, Vol. 18. Part 2. Indexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-09-01

This bibliography contains 3638 citations with abstracts of documents relevant to environmental restoration, nuclear facility decontamination and decommissioning (D&D), uranium mill tailings management, and site remedial actions. This report is the eighteenth in a series of bibliographies prepared annually for the U.S. Department of Energy (DOE) Office of Environmental Restoration. Citations to foreign and domestic literature of all types - technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions - have been included in Part 1 of the report. The bibliography contains scientific, technical, financial, and regulatory information that pertains to DOE environmentalmore » restoration programs. The citations are separated by topic into 16 sections, including (1) DOE Environmental Restoration Program; (2) DOE D&D Program; (3) Nuclear Facilities Decommissioning; (4) DOE Formerly Utilized Sites Remedial Action Programs; (5) NORM-Contaminated Site Restoration; (6) DOE Uranium Mill Tailings Remedial Action Project; (7) Uranium Mill Tailings Management; (8) DOE Site-Wide Remedial Actions; (9) DOE Onsite Remedial Action Projects; (10) Contaminated Site Remedial Actions; (11) DOE Underground Storage Tank Remediation; (12) DOE Technology Development, Demonstration, and Evaluations; (13) Soil Remediation; (14) Groundwater Remediation; (15) Environmental Measurements, Analysis, and Decision-Making; and (16) Environmental Management Issues. Within the 16 sections, the citations are sorted by geographic location. If a geographic location is not specified, the citations are sorted according to the document title. In Part 2 of the report, indexes are provided for author, author affiliation, selected title phrase, selected title word, publication description, geographic location, and keyword.« less

Nuclear facility decommissioning and site remedial actions: a selected bibliography. Volume 5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owen, P.T.; Knox, N.P.; Chilton, B.D.

1984-09-01

This bibliography of 756 references with abstracts on the subject of nuclear facility decommissioning, uranium mill tailings management, and site remedial actions is the fifth in a series of annual reports prepared for the US Department of Energy, Division of Remedial Action Projects. Foreign as well as domestic literature of all types - technical reports, progress reports, journal articles, conference papers, symposium proceedings, theses, books, patents, legislation, and research project descriptions - has been included in this publication. The bibliography contains scientific (basic research as well as applied technology), economic, regulatory, and legal literature pertinent to the US Department ofmore » Energy's Remedial Action Program. Major chapters are: (1) Surplus Facilities Management Program; (2) Nuclear Facilities Decommissioning; (3) Formerly Utilized Sites Remedial Action Program; (4) Uranium Mill Tailings Remedial Action Program; (5) Grand Junction Remedial Action Program; (6) Uranium Mill Tailings Management; and (7) Technical Measurements Center. Chapter sections for chapters 1, 2, 4, and 6 include Design, Planning, and Regulations; Environmental Studies and Site Surveys; Decontamination Studies; Dismantlement and Demolition; Site Stabilization and Reclamation; Waste Disposal; Remedial Action Experience; and General Studies. The references within each chapter or section are arranged alphabetically by leading author. References having no individual author are arranged by corporate author or by title. Indexes are provided for the categories of author, corporate affiliation, title, publication description, geographic location, and keywords. The Appendix contains a list of frequently used acronyms.« less

Reproductive and biochemical biomarkers in largemouth bass sampled downstream of a pulp and paper mill in Florida

USGS Publications Warehouse

Sepulveda, M.S.; Gallagher, E.P.; Wieser, C.M.; Gross, T.S.

2004-01-01

The objective of this study was to evaluate the effects of bleached/unbleached kraft mill effluents (B/UKME) on the reproductive parameters of free-ranging Florida largemouth bass (Micropterus salmoides floridanus). The reproductive parameters measured included gonadosomatic index (GSI), histological evaluation of gonads, and plasma concentrations of vitellogenin (VTG), 17??-estradiol, and 11-ketotestosterone (11-KT). Hepatic ethoxyresorufin-O-deethylase (EROD) activity was measured as a marker of exposure to cytochrome P450-inducing agents in these effluents. Endpoints were compared among adult bass sampled from tributary and mainstream effluent-contaminated and reference sites. Females sampled from the site closest to the mill outfall had a significant five-fold increase in EROD activity compared to bass sampled from reference streams. Although sex hormones were significantly reduced in bass from exposed sites, there were no differences in VTG and GSI across sites. The absence of organism-level responses was probably not related to a lack of sensitivity, as previous studies in our laboratory have shown that bass exposed to these effluents exhibit changes in GSI and in other measures associated with reproductive success. In females, inverse relationships were observed between VTG and GSI and EROD activity. These relationship, however, were not consistent within all of the sites studied. Collectively, our findings indicate that hepatic EROD induction is an effective marker of B/UKME exposure in largemouth bass and that it might be associated with antiestrogenic effects in this species. ?? 2003 Elsevier Inc. All rights reserved.

Comparison of five-axis milling and rapid prototyping for implant surgical templates.

PubMed

Park, Ji-Man; Yi, Tae-Kyoung; Koak, Jai-Young; Kim, Seong-Kyoon; Park, Eun-Jin; Heo, Seong-Joo

2014-01-01

This study aims to compare and evaluate the accuracy of surgical templates fabricated using coordinate synchronization processing with five-axis milling and design-related processing with rapid prototyping (RP). Master phantoms with 10 embedded gutta-percha cylinders hidden under artificial gingiva were fabricated and imaged using cone beam computed tomography. Vectors of the hidden cylinders were extracted and transferred to those of the planned implants through reverse engineering using virtual planning software. An RP-produced template was fabricated by stereolithography in photopolymer at the RP center according to planned data. Metal sleeves were bonded after holes were bored (group RP). For the milled template, milling coordinates were synchronized using the conversion process for the coordinate synchronization platform located on the model's bottom. Metal bushings were set on holes milled on the five-axis milling machine, on which the model was fixed through the coordinate synchronization plate, and the framework was constructed on the model using orthodontic resin (group CS). A computed tomography image was taken with templates firmly fixed on models using anchor pins (RP) or anchor screws (CS). The accuracy was analyzed via reverse engineering. Differences between the two groups were compared by repeated measures two-factor analysis. From the reverse-engineered image of the template on the experimental model, RP-produced templates showed significantly larger deviations than did milled surgical guides. Maximum deviations of the group RP were 1.58 mm (horizontal), 1.68 mm (vertical), and 8.51 degrees (angular); those of the group CS were 0.68 mm (horizontal), 0.41 mm (vertical), and 3.23 degrees (angular). A comparison of milling and RP template production methods showed that a vector-milled surgical guide had significantly smaller deviations than did an RP-produced template. The accuracy of computer-guided milled surgical templates was within the safety margin of previous studies.

An evaluation of biomarkers of reproductive function and potential contaminant effects in Florida largemouth bass ( Micropterus salmoidesfloridanus) sampled from the St. Johns River.

PubMed

Sepúlveda, María S; Johnson, William E; Higman, John C; Denslow, Nancy D; Schoeb, Trenton R; Gross, Timothy S

2002-04-22

The objective of this study was to describe and compare several reproductive parameters for Florida largemouth bass (Micropterus salmoides floridanus) inhabiting the St. Johns River and exposed to different types and/or degrees of contamination. Welaka was selected as the reference site in this study because of its low urban and agricultural development, Palatka is in close proximity to a paper mill plant, the Green Cove site is influenced by marine shipping activities and Julington Creek site receives discharges of domestic wastewater and storm water runoff from recreational boating marinas. For this study, bass were sampled both prior to (September 1996) and during the spawning season (February 1997). In order to characterize chemical exposure, bass livers were analyzed for up to 90 trace organics and 11 trace metal contaminants. Reproductive parameters measured included gonadosomatic index (GSI), histological evaluation of gonads and plasma concentrations of vitellogenin (VTG), 17beta-estradiol (E2) and 11-ketotestosterone (11-KT). In general, the sum of organic chemicals was highest in livers from Palatka bass and bass from Green Cove and Julington Creek had higher hepatic concentrations of low molecular polycyclic aromatic hydrocarbons and polychlorinated biphenyls when compared to fish from Welaka. Metals were more variable across sites, with highest mean concentrations found in bass from either Julington Creek (Ag, As, Cr, Cu, Zn) or Welaka (Cd, Hg, Pb, Se, Tn). Female bass from Palatka and Green Cove had lower concentrations of E2, VTG and lower GSI in relation to Welaka. Males from Palatka and Green Cove showed comparable declines in 11-KT in relation to males from Julington Creek and GSI were decreased only in Palatka males. These results indicate a geographical trend in reproductive effects, with changes being most pronounced at the site closest to the paper mill (Palatka) and decreasing as the St. Johns River flows downstream. Since reproductive alterations were most evident in bass sampled from the site closest to the paper mill discharge, it is possible that exposure to these effluents might explain at least some of the results reported here. However, the presence of reproductive alterations in fish sampled at a considerable distance from the mill discharge (Green Cove, 40 km) would suggest exposure to chemicals released from sources other than the paper mill plant. It is clear that additional studies are needed to evaluate the potential impact of these reproductive changes in populations of Florida largemouth bass inhabiting the St. Johns River.

An evaluation of biomarkers of reproductive function and potential contaminant effects in Florida largemouth bass (Micropterus salmoides floridanus) sampled from the St. Johns River

USGS Publications Warehouse

Sepulveda, M.S.; Johnson, W.E.; Higman, J.C.; Denslow, N.D.; Schoeb, T.R.; Gross, T.S.

2002-01-01

The objective of this study was to describe and compare several reproductive parameters for Florida largemouth bass (Micropterus salmoides floridanus) inhabiting the St. Johns River and exposed to different types and/or degrees of contamination. Welaka was selected as the reference site in this study because of its low urban and agricultural development, Palatka is in close proximity to a paper mill plant, the Green Cove site is influenced by marine shipping activities and Julington Creek site receives discharges of domestic wastewater and storm water runoff from recreational boating marinas. For this study, bass were sampled both prior to (September 1996) and during the spawning season (February 1997). In order to characterize chemical exposure, bass livers were analyzed for up to 90 trace organics and 11 trace metal contaminants. Reproductive parameters measured included gonadosomatic index (GSI), histological evaluation of gonads and plasma concentrations of vitellogenin (VTG), 17??-estradiol (E2) and 11-ketotestosterone (11-KT). In general, the sum of organic chemicals was highest in livers from Palatka bass and bass from Green Cove and Julington Creek had higher hepatic concentrations of low molecular polycyclic aromatic hydrocarbons and polychlorinated biphenyls when compared to fish from Welaka. Metals were more variable across sites, with highest mean concentrations found in bass from either Julington Creek (Ag, As, Cr, Cu, Zn) or Welaka (Cd, Hg, Pb, Se, Tn). Female bass from Palatka and Green Cove had lower concentrations of E2, VTG and lower GSI in relation to Welaka. Males from Palatka and Green Cove showed comparable declines in 11-KT in relation to males from Julington Creek and GSI were decreased only in Palatka males. These results indicate a geographical trend in reproductive effects, with changes being most pronounced at the site closest to the paper mill (Palatka) and decreasing as the St. Johns River flows downstream. Since reproductive alterations were most evident in bass sampled from the site closest to the paper mill discharge, it is possible that exposure to these effluents might explain at least some of the results reported here. However, the presence of reproductive alterations in fish sampled at a considerable distance from the mill discharge (Green Cove, 40 km) would suggest exposure to chemicals released from sources other than the paper mill plant. It is clear that additional studies are needed to evaluate the potential impact of these reproductive changes in populations of Florida largemouth bass inhabiting the St. Johns River. ?? 2002 Elsevier Science B.V. All rights reserved.

Molecular implications of drug-polymer solubility in understanding the destabilization of solid dispersions by milling.

PubMed

Yang, Ziyi; Nollenberger, Kathrin; Albers, Jessica; Qi, Sheng

2014-07-07

The solubility of drugs in polymer matrixes has been recognized as one of the key factors governing the physical stability of solid dispersions. This study has explored the implications of drug solubility on the destabilization that occurs on milling, which is often used as an additional process for hot melt extruded (HME) solid dispersions. The theoretical drug solubility in the polymer was first predicted using various theoretical and experimental approaches. The destabilization effects of high-energy mechanical milling on the solid dispersions with drug loadings below and above the predicted solubility were then investigated using a range of thermal, microscopic, and spectroscopic techniques. Four model drug-polymer combinations were studied. The HME formulations with drug loading below the predicted solid solubility (undersaturated and true molecular dispersion) showed good stability against milling. In contrast, milling destabilized supersaturated HME dispersions via increasing molecular mobility and creating phase-separated, amorphous, drug-rich domains. However, these additional amorphous drug-rich domains created by milling show good stability under ambient conditions, though crystallization can be accelerated by additional heating. These results highlighted that the processing method used to prepare the solid dispersions may play a role in facilitating the stabilization of amorphous drug in supersaturated solid dispersions. The degree of supersaturation of the drug in the polymer showed significant impact on the destabilization behavior of milling on solid dispersions. An improved understanding of the destabilization behavior of solid dispersions upon milling can provide new insights into the processing related apparent solubility of drugs in polymers.

Off-Site Radiation Exposure Review Project: Phase 2 soils program

DOE Office of Scientific and Technical Information (OSTI.GOV)

McArthur, R.D.; Miller, F.L. Jr.

1989-12-01

To help estimate population doses of radiation from fallout originating at the Nevada Test Site, soil samples were collected throughout the western United States. Each sample was prepared by drying and ball-milling, then analyzed by gamma-spectrometry to determine the amount of {sup 137}Cs it contained. Most samples were also analyzed by chemical separation and alpha-spectrometry to determine {sup 239 + 240}Pu and by isotope mass spectroscopy to determine the ratios of {sup 240}Pu to {sup 239}Pu and {sup 241}Pu to {sup 239}Pu. The total inventories of cesium and plutonium at 171 sites were computed from the results. This report describesmore » the sample collection, processing, and analysis, presents the analytical results, and assesses the quality of the data. 10 refs., 9 figs., 12 tabs.« less

Health implications of radionuclide levels in cattle raised near U mining and milling facilities in Ambrosia Lake, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lapham, S.C.; Millard, J.B.; Samet, J.M.

1989-03-01

This study was conducted to determine radionuclide tissue levels in cattle raised near U mining and milling facilities. Ambrosia Lake, New Mexico, has been the site of extensive U mining for 30 y and contains several underground U mines, a processing mill, and two large U tailings piles. Ten cows were purchased from two grazing areas in Ambrosia Lake and ten control animals were purchased from Crownpoint, New Mexico. Muscle, liver, kidney, and bone tissue taken from these animals, and environmental samples, including water, grasses and soil collected from the animals' grazing areas, were analyzed for /sup 238/U, /sup 234/U,more » /sup 230/Th, /sup 226/Ra, /sup 210/Pb, and /sup 210/Po. Mean radionuclide levels in cattle tissue and environmental samples from Ambrosia Lake were higher in almost every comparison than those found in respective controls. Liver and kidney tissues were particularly elevated in /sup 226/Ra and /sup 210/Po. Radiation dose commitments from eating cattle tissue with these radionuclide concentrations were calculated. We concluded that the health risk to the public from eating exposed cattle is minimal, unless large amounts of this tissue, especially liver and kidney, are ingested.« less

PPSITE - A New Method of Site Evaluation for Longleaf Pine: Model Development and User's Guide

Treesearch

Constance A. Harrington

1990-01-01

A model was developed to predict site index (base age 50 years) for longleaf pine (Pinus palustris Mill.). The model, named PPSITE, was based on soil characteristics, site location on the landscape, and land history. The model was constrained so that the relationship between site index and each soil-site variable was consistent with what was known...

A Generational Change in Site Index for Naturally Established Longleaf Pine on a South Alabama Coastal Plain Site

Treesearch

William D. Boyer

2001-01-01

Research on longleaf pine (Pinus palustris Mill.) has been carried out for over 50 yr on a coastal plain site in south Alabama. Studies havie included the original second-growth stands and also naturally established third-growth stands. Site index data revealed that estimated site index values for third growth generally exceeded those for second...

A generational change in site index for naturally established longleaf pine on a south Alabama Coastal Plain site

Treesearch

William D. Boyer

2001-01-01

Research on longleaf pine (Pinus palustris Mill.) has been carried out for over 50 yr on a Coastal Plain site in south Alabama. Studies have included the original second-growth stands and also naturally established third-growth stands. Site index data revealed that estimated site index values for third growth generally exceeded those for second...

Energy and greenhouse gas profiles of polyhydroxybutyrates derived from corn grain: a life cycle perspective.

PubMed

Kim, Seungdo; Dale, Bruce E

2008-10-15

Polyhydroxybutyrates (PHB) are well-known biopolymers derived from sugars orvegetable oils. Cradle-to-gate environmental performance of PHB derived from corn grain is evaluated through life cycle assessment (LCA), particularly nonrenewable energy consumption and greenhouse gas emissions. Site-specific process information on the corn wet milling and PHB fermentation and recovery processes was obtained from Telles. Most of energy used in the corn wet milling and PHB fermentation and recovery processes is generated in a cogeneration power plant in which corn stover, assumed to be representative of a variety of biomass sources that could be used, is burned to generate electricity and steam. County level agricultural information is used in estimating the environmental burdens associated with both corn grain and corn stover production. Results show that PHB derived from corn grain offers environmental advantages over petroleum-derived polymers in terms of nonrenewable energy consumption and greenhouse gas emissions. Furthermore, PHB provides greenhouse gas credits, and thus PHB use reduces greenhouse gas emissions compared to petroleum-derived polymers. Corn cultivation is one of the environmentally sensitive areas in the PHB production system. More sustainable practices in corn cultivation (e.g., using no-tillage and winter cover crops) could reduce the environmental impacts of PHB by up to 72%.

High-resolution neutron diffraction study of microstructural changes in nanocrystalline ball-milled niobium carbide NbC{sub 0.93}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balagurov, Anatoly M.; Bobrikov, Ivan A.; Bokuchava, Gizo D.

2015-11-15

High resolution neutron diffraction was applied for elucidating of the microstructural evolution of nanocrystalline niobium carbide NbC{sub 0.93} powders subjected to high-energy ball milling. The diffraction patterns were collected with the high resolution Fourier diffractometer HRFD by using the reverse time-of-flight (RTOF) mode of data acquisition. The traditional single diffraction line analysis, the Rietveld method and more advanced Whole Powder Pattern Modeling technique were applied for the data analysis. The comparison of these techniques was performed. It is established that short-time milling produces a non-uniform powder, in which two distinct fractions with differing microstructure can be identified. Part of themore » material is in fact milled efficiently, with a reduction in grain size, an increase in the quantity of defects, and a corresponding tendency to decarburize reaching a composition NbC{sub 0.80} after 15 h of milling. The rest of the powder is less efficiently processed and preserves its composition and lower defect content. Larger milling times should have homogenized the system by increasing the efficiently milled fraction, but the material is unable to reach a uniform and homogeneous state. It is definitely shown that RTOF neutron diffraction patterns can provide the very accurate data for microstructure analysis of nanocrystalline powders. - Highlights: • The NbC{sub 0.93} powder was processed by high-energy ball milling. • The microstrain and dislocation density increase with milling time increase. • The corresponding decrease in crystallite size with milling time was observed. • The material exhibits the presence of two fractions after ball milling. • The RTOF neutron diffraction data are suitable for accurate microstructure analysis.« less

40 CFR 63.1341 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... other materials to form cement. Clinker cooler means equipment into which clinker product leaving the... kiln or coal mills using exhaust gases from the clinker cooler are not an in-line coal mill. In-line kiln/raw mill means a system in a portland cement production process where a dry kiln system is...

40 CFR 63.1341 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... other materials to form cement. Clinker cooler means equipment into which clinker product leaving the... kiln or coal mills using exhaust gases from the clinker cooler are not an in-line coal mill. In-line kiln/raw mill means a system in a portland cement production process where a dry kiln system is...

Wheat mill stream properties for discrete element method modeling

USDA-ARS?s Scientific Manuscript database

A discrete phase approach based on individual wheat kernel characteristics is needed to overcome the limitations of previous statistical models and accurately predict the milling behavior of wheat. As a first step to develop a discrete element method (DEM) model for the wheat milling process, this s...

Milled industrial beet color kinetics and total soluble solid contents by image analysis

USDA-ARS?s Scientific Manuscript database

Industrial beets are an emerging feedstock for biofuel and bioproducts industry in the US. Milling of industrial beets is the primary step in front end processing (FEP) for ethanol production. Milled beets undergo multiple pressings with water addition during raw beet juice extraction, and extracted...

14. View of ruins at southeast corner of site between ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. View of ruins at southeast corner of site between Clay Storage Silo (on left) and Wilder Mill (on right); view to southwest. - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

Insect pest management decisions in food processing facilities

USDA-ARS?s Scientific Manuscript database

Pest management decision making in food processing facilities such as flour mills, rice mills, human and pet food manufacturing facilities, distribution centers and warehouses, and retail stores is a challenging undertaking. Insect pest management programs require an understanding of the food facili...

75 FR 17126 - Foreign-Trade Zone 26-Atlanta, Georgia, Application for Expansion and Reorganization under...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

..., Jeffersonville (Twiggs County); Site 16 (308 acres) -- Meridian 75 Logistics Center, located at Interstate 75 and Rumble Road, Forsyth (Monroe County); Site 17 (193 acres) -- Majestic Airport Center III, located at... Futral Road, Griffin (Spalding County); Site 9 (321 acres) -- at the Hamilton Mill Business Center...

Uranium association with iron-bearing phases in mill tailings from Gunnar, Canada.

PubMed

Othmane, Guillaume; Allard, Thierry; Morin, Guillaume; Sélo, Madeleine; Brest, Jessica; Llorens, Isabelle; Chen, Ning; Bargar, John R; Fayek, Mostafa; Calas, Georges

2013-11-19

The speciation of uranium was studied in the mill tailings of the Gunnar uranium mine (Saskatchewan, Canada), which operated in the 1950s and 1960s. The nature, quantification, and spatial distribution of uranium-bearing phases were investigated by chemical and mineralogical analyses, fission track mapping, electron microscopy, and X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) spectroscopies at the U LIII-edge and Fe K-edge. In addition to uranium-containing phases from the ore, uranium is mostly associated with iron-bearing minerals in all tailing sites. XANES and EXAFS data and transmission electron microscopy analyses of the samples with the highest uranium concentrations (∼400-700 mg kg(-1) of U) demonstrate that uranium primarily occurs as monomeric uranyl ions (UO2(2+)), forming inner-sphere surface complexes bound to ferrihydrite (50-70% of the total U) and to a lesser extent to chlorite (30-40% of the total U). Thus, the stability and mobility of uranium at the Gunnar site are mainly influenced by sorption/desorption processes. In this context, acidic pH or alkaline pH with the presence of UO2(2+)- and/or Fe(3+)-complexing agents (e.g., carbonate) could potentially solubilize U in the tailings pore waters.

A new milling machine for computer-aided, in-office restorations.

PubMed

Kurbad, Andreas

Chairside computer-aided design/computer-aided manufacturing (CAD/CAM) technology requires an effective technical basis to obtain dental restorations with optimal marginal accuracy, esthetics, and longevity in as short a timeframe as possible. This article describes a compact, 5-axis milling machine based on an innovative milling technology (5XT - five-axis turn-milling technique), which is capable of achieving high-precision milling results within a very short processing time. Furthermore, the device's compact dimensioning and state-of-the-art mode of operation facilitate its use in the dental office. This model is also an option to be considered for use in smaller dental laboratories, especially as the open input format enables it to be quickly and simply integrated into digital processing systems already in use. The possibility of using ceramic and polymer materials with varying properties enables the manufacture of restorations covering all conceivable indications in the field of fixed dental prosthetics.

Preparation of Si nano-crystals with controlled oxidation state from SiO disproportionated by ZrO2 ball-milling

NASA Astrophysics Data System (ADS)

Okamoto, Yuji; Harada, Yoshitomo; Ohta, Narumi; Takada, Kazunori; Sumiya, Masatomo

2016-09-01

We demonstrate that a SiO disproportionation reaction can be achieved simply by high energy mechanochemical milling. The planetary ball-milling of ZrO2 for a few minutes generated Si nano-crystals. Milling conditions including rotation speed, ball number, milling time, and type of ball material were able to control the oxidation states of Si. The ball-milled SiO powder was tested as an anode of a lithium battery. ZrO2 contamination from the vial and balls was eliminated by dipping the ball-milled SiO powder in (NH4)HSO4 molten salt and heating for 5 min. The disproportionated SiO powder showed characteristics comparable to those of a powder prepared by a conventional heating process taking several hours.

The milling of pristine and brominated P-100 graphite fibers

NASA Technical Reports Server (NTRS)

Dillehay, M. E.; Gaier, J. R.

1986-01-01

Techniques were developed for the ball milling of pristine and brominated P-100 graphite fibers. Because of the lubrication properties of graphite, large ball loads (50 percent by volume) were required. Use of 2-propanol as a milling medium enhanced the efficiency of the process. Milled brominated P-100 fibers had resistivities which were indistinguishable from milled pristine P-100 fibers. Apparent loss of bromine from the brominated fibers suggests that bromine would not be the intercalate of choice in applications where milled fibers of this type are required. Other intercalates which do not degas may be more appropriate for a milled fiber application. These same results, however, do provide evidence that bromine molecules leave the fiber surface when removed from overpressure of bromine. While exploring possible solvent media for milling purposes, it was found that brominated fibers are stable in a wide variety of organic solvents.

Fracture, roughness and phase transformation in CAD/CAM milling and subsequent surface treatments of lithium metasilicate/disilicate glass-ceramics.

PubMed

Alao, Abdur-Rasheed; Stoll, Richard; Song, Xiao-Fei; Abbott, John R; Zhang, Yu; Abduo, Jaafar; Yin, Ling

2017-10-01

This paper studied surface fracture, roughness and morphology, phase transformations, and material removal mechanisms of lithium metasilicate/disilicate glass ceramics (LMGC/LDGC) in CAD/CAM-milling and subsequent surface treatments. LMGC (IPS e.max CAD) blocks were milled using a chairside dental CAD/CAM milling unit and then treated in sintering, polishing and glazing processes. X-ray diffraction was performed on all processed surfaces. Scanning electron microscopy (SEM) was applied to analyse surface fracture and morphology. Surface roughness was quantitatively characterized by the arithmetic average surface roughness R a and the maximum roughness R z using desktop SEM-assisted morphology analytical software. The CAD/CAM milling induced extensive brittle cracks and crystal pulverization on LMGC surfaces, which indicate that the dominant removal mechanism was the fracture mode. Polishing and sintering of the milled LMGC lowered the surface roughness (ANOVA, p < 0.05), respectively, while sintering also fully transformed the weak LMGC to the strong LDGC. However, polishing and glazing of LDGC did not significantly improve the roughness (ANOVA, p > 0.05). In comparison of all applied fabrication process routes, it is found that CAD/CAM milling followed by polishing and sintering produced the smoothest surface with R a = 0.12 ± 0.08µm and R z = 0.89 ± 0.26µm. Thus , it is proposed as the optimized process route for LMGC/LDGC in dental restorations. This route enables to manufacture LMGC/LDGC restorations with cost effectiveness, time efficiency, and improved surface quality for better occlusal functions and reduced bacterial plaque accumulation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluating the Role of Small Impoundments in Legacy Sediment Storage

NASA Astrophysics Data System (ADS)

Bain, D. J.; Salant, N.; Green, M. B.; Wreschnig, A. J.; Urbanova, T.

2009-12-01

Recent research highlighting the prevalence of dams built for water power in the mid-1800s has led to suggestions that strategies for managing legacy sediment in the Eastern United States should be re-evaluated. However, the link between reach-scale observations of historic dam sites to processes at the catchment scale have not been examined, nor have the role of other, similar historic changes been evaluated. This presentation will compare dam dynamics, including mill density data and synthetic estimates of beaver populations with sedimentation rates recorded in sediment cores. If low-head dams were a dominant mechanism in sediment storage, we expect to see changes in sedimentation rates with the expatriation of the beaver and the rise and decline of water power. Further, we expect to see spatial variation in these changes as beaver and mill densities and potential sediment yield are spatially heterogeneous. Ultimately, dramatic changes in sediment yield due to land use and hydrological alterations likely drove sedimentation rates; the mechanistic importance of storage likely depends on temporal coincidence.

Determination of rational parameters for process of grinding materials pre-crushed by pressure in ball mill

NASA Astrophysics Data System (ADS)

Romanovich, A. A.; Romanovich, L. G.; Chekhovskoy, E. I.

2018-03-01

The article presents the results of experimental studies on the grinding process of a clinker preliminarily ground in press roller mills in a ball mill equipped with energy exchange devices. The authors studied the influence of the coefficients of loading for grinding bodies of the first and second mill chambers, their lengths, angles of inclination, and the mutual location of energy exchange devices (the ellipse segment and the double-acting blade) on the output parameters of the grinding process (productivity, drive power consumption and specific energy consumption). It is clarified that the best results of the disaggregation and grinding process, judging by the minimum specific energy consumption in the grinding of clinker with an anisotropic texture after force deformation between the rolls of a press roller shredder, are achieved at a certain angle of ellipse segment inclination; the length of the first chamber and the coefficients of loading the chambers with grinding bodies.

35. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill, oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

35. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill, one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: Bevel gear at lower end of vertical drive shaft in foreground turned bevel gear of top roll when the vertical drive shaft was in place in the brass-bearing socket in the middle ground of the photograph. The bolts above the top roll and at the side of the two bottom rolls adjusted the pressure and position of the rolls' brass bearings. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

A comparison of field-dependent rheological properties between spherical and plate-like carbonyl iron particles-based magneto-rheological fluids

NASA Astrophysics Data System (ADS)

Tan Shilan, Salihah; Amri Mazlan, Saiful; Ido, Yasushi; Hajalilou, Abdollah; Jeyadevan, Balachandran; Choi, Seung-Bok; Azhani Yunus, Nurul

2016-09-01

This work proposes different sizes of the plate-like particles from conventional spherical carbonyl iron (CI) particles by adjusting milling time in the ball mill process. The ball mill process to make the plate-like particles is called a solid-state powder processing technique which involves repeated welding, fracturing and re-welding of powder particles in a high-energy ball mill. The effect of ball milling process on the magnetic behavior of CI particles is firstly investigated by vibrating sample magnetometer. It is found form this investigation that the plate-like particles have higher saturation magnetization (about 8%) than that of the spherical particles. Subsequently, for the investigation on the sedimentation behavior the cylindrical measurement technique is used. It is observed from this measurement that the plate-like particles show slower sedimentation rate compared to the spherical particles indicating higher stability of the MR fluid. The field-dependent rheological properties of MR fluids based on the plate-like particles are then investigated with respect to the milling time which is directly connected to the size of the plate-like particles. In addition, the field-dependent rheological properties such as the yield stress are evaluated and compared between the plate-like particles based MR fluids and the spherical particles based MR fluid. It is found that the yield shear stress of the plate-like particles based MR fluid is increased up to 270% compared to the spherical particles based MR fluid.

The timber industries of Pennsylvania, 1988

Treesearch

Eric H. Wharton; John L. Bearer; John L. Bearer

1993-01-01

Evaluates regional timber output of Pennsylvania. Results are based on a survey of primary processing mills located in the state, and of mills in other states that used wood from Pennsylvania. Contains statistics on industrial timber production and mill receipts and the production and final end use of manufacturing residues. Comparisons are made between historical and...

Role of intensive milling in the processing of barium ferrite/magnetite/iron hybrid magnetic nano-composites via partial reduction of barium ferrite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molaei, M.J., E-mail: mj.molaee@merc.ac.ir; Delft Chem Tech, Faculty of Applied Sciences, Delft University of Technology, Julianalaan 136, 2628 BL Delft; Ataie, A.

2015-03-15

In this research a mixture of barium ferrite and graphite was milled for different periods of time and then heat treated at different temperatures. The effects of milling time and heat treatment temperature on the phase composition, thermal behavior, morphology and magnetic properties of the samples have been investigated using X-ray diffraction, differential thermal analysis, high resolution transmission electron microscopy and vibrating sample magnetometer techniques, respectively. X-ray diffraction results revealed that BaFe{sub 12}O{sub 19}/Fe{sub 3}O{sub 4} nanocomposites form after a 20 h milling due to the partial reduction of BaFe{sub 12}O{sub 19}. High resolution transmission electron microscope images of amore » 40 h milled sample showed agglomerated structure consisting of nanoparticles with a mean particle size of 30 nm. Thermal analysis of the samples via differential thermal analysis indicated that for un-milled samples, heat treatment up to 900 °C did not result in α-Fe formation, while for a 20 h milled sample heat treatment at 700 °C resulted in reduction process progress to the formation of α-Fe. Wustite was disappeared in an X-ray diffraction pattern of a heat treated sample at 850 °C, by increasing the milling time from 20 to 40 h. By increasing the milling time, the structure of heat treated samples becomes magnetically softer due to an increase in saturation magnetization and a decrease in coercivity. Saturation magnetization and coercivity of a sample milled for 20 h and heat treated at 850 °C were 126.3 emu/g and 149.5 Oe which by increasing the milling time to 40 h, alter to 169.1 emu/g and 24.3 Oe, respectively. High coercivity values of milled and heat treated samples were attributed to the nano-scale formed iron particles. - Graphical abstract: Display Omitted - Highlights: • Barium ferrite and graphite were treated mechano-thermally. • Increasing milling time increases reduction progress after heat treatment. • Composites including iron nano-crystals forms by milling and heat treatment. • Shorter milling time results in higher H{sub C} of the milled and heat treated samples.« less

Impact of planetary ball milling parameters on the microstructure and pinning properties of polycrystalline superconductor Y3Ba5Cu8Oy

NASA Astrophysics Data System (ADS)

Slimani, Y.; Hannachi, E.; Azzouz, F. Ben; Salem, M. Ben

2018-06-01

We have reported the influence of planetary high energy ball milling parameters on morphology, microstructure and flux pinning capability of polycrystalline Y3Ba5Cu8Oy. Samples were prepared through the standard solid-state reaction by using two different milling methods, ball milling in a planetary crusher and hand grinding in a mortar. Phase analysis by X-ray diffraction (XRD) method, microstructural examination by scanning electron microscope (SEM), electrical resistivity, the global and intra-granular critical current densities measurements are done to characterize the samples. The processing parameters of the planetary milling have a considerable impact on the final product properties. SEM observations show the presence of nanoscale entities submerged within the Y3Ba5Cu8Oy crystallites. The results show that the fine grain microstructure of the Y3Ba5Cu8Oy bulk induced by ball milling process contributes to critical currents density enhancement in the magnetic field and promotes an optimized flux pinning ability.

Design and Development of a Three-Component Force Sensor for Milling Process Monitoring

PubMed Central

Li, Yingxue; Zhao, Yulong; Fei, Jiyou; Qin, Yafei; Zhao, You; Cai, Anjiang; Gao, Song

2017-01-01

A strain-type three-component table dynamometer is presented in this paper, which reduces output errors produced by cutting forces imposed on the different milling positions of a workpiece. A sensor structure with eight parallel elastic beams is proposed, and sensitive regions and Wheastone measuring circuits are also designed in consideration of eliminating the influences of the eccentric forces. To evaluate the sensor decoupling performance, both of the static calibration and dynamic milling test were implemented in different positions of the workpiece. Static experiment results indicate that the maximal deviation between the measured forces and the standard inputs is 4.58%. Milling tests demonstrate that with same machining parameters, the differences of the measured forces between different milling positions derived by the developed sensor are no larger than 6.29%. In addition, the natural frequencies of the dynamometer are kept higher than 2585.5 Hz. All the measuring results show that as a strain-type dynamometer, the developed force sensor has an improved eccentric decoupling accuracy with natural frequencies not much decreased, which owns application potential in milling process monitoring. PMID:28441354

Nanocomposite bulk of mechanically milled Al-Pb samples consolidated pore-free by the high-energy rate forming technique.

PubMed

Csanády, Agnes; Sajó, István; Lábár, János L; Szalay, András; Papp, Katalin; Balaton, Géza; Kálmán, Erika

2005-06-01

It is shown that pore-free bulk samples were produced by the high-energy rate forming axis-symmetrical powder compaction method for different application purposes in case of the very different, immiscible Al and Pb metal pair. The starting Al-Pb nanocomposites were made by mechanical milling of atomized Al and Pb powders either in a SPEX 9000 or a Fritsch Pulverisette 4 mill. Due to the conditions that milling was carried out in air, the PbO layer, originally existing at the surface of the atomized Pb powder, ruptured and was also dispersed in the composite. The presence of the nano PbO particles was proven by XRD and TEM (BF, DF, SAED). When the energy of milling was high, the PbO crystallites became so small that they could hardly be seen by XRD technique. Local distribution of the PbO nanoparticles was still visible in a TEM, using the process diffraction method. Both XRD and SAED proved to be useful for the evaluation of the results of the milling process and compaction.

Synthesis of Nano-Crystalline Gamma-TiAl Materials

NASA Technical Reports Server (NTRS)

Hales, Stephen J.; Vasquez, Peter

2003-01-01

One of the principal problems with nano-crystalline materials is producing them in quantities and sizes large enough for valid mechanical property evaluation. The purpose of this study was to explore an innovative method for producing nano-crystalline gamma-TiAl bulk materials using high energy ball milling and brief secondary processes. Nano-crystalline powder feedstock was produced using a Fritsch P4(TM) vario-planetary ball mill recently installed at NASA-LaRC. The high energy ball milling process employed tungsten carbide tooling (vials and balls) and no process control agents to minimize contamination. In a collaborative effort, two approaches were investigated, namely mechanical alloying of elemental powders and attrition milling of pre-alloyed powders. The objective was to subsequently use RF plasma spray deposition and short cycle vacuum hot pressing in order to effect consolidation while retaining nano-crystalline structure in bulk material. Results and discussion of the work performed to date are presented.

PLYMAP : a computer simulation model of the rotary peeled softwood plywood manufacturing process

Treesearch

Henry Spelter

1990-01-01

This report documents a simulation model of the plywood manufacturing process. Its purpose is to enable a user to make quick estimates of the economic impact of a particular process change within a mill. The program was designed to simulate the processing of plywood within a relatively simplified mill design. Within that limitation, however, it allows a wide range of...

Minimization of energy and surface roughness of the products machined by milling

NASA Astrophysics Data System (ADS)

Belloufi, A.; Abdelkrim, M.; Bouakba, M.; Rezgui, I.

2017-08-01

Metal cutting represents a large portion in the manufacturing industries, which makes this process the largest consumer of energy. Energy consumption is an indirect source of carbon footprint, we know that CO2 emissions come from the production of energy. Therefore high energy consumption requires a large production, which leads to high cost and a large amount of CO2 emissions. At this day, a lot of researches done on the Metal cutting, but the environmental problems of the processes are rarely discussed. The right selection of cutting parameters is an effective method to reduce energy consumption because of the direct relationship between energy consumption and cutting parameters in machining processes. Therefore, one of the objectives of this research is to propose an optimization strategy suitable for machining processes (milling) to achieve the optimum cutting conditions based on the criterion of the energy consumed during the milling. In this paper the problem of energy consumed in milling is solved by an optimization method chosen. The optimization is done according to the different requirements in the process of roughing and finishing under various technological constraints.

Application of Odor Sensors to Ore Sorting and Mill Feed Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael G. Nelson

2005-08-01

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modeling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing that will allow optimization of the mill processes on an almost real-time basis. This is not happening because mill feed it ismore » often treated as a uniform material, when in reality it varies in composition and characteristics. An investigation was conducted to assess the suitability of odor sensors for maintaining traceability in ore production and processing. Commercially available sensors are now used in food processing, environmental monitoring, and other applications and can detect the presence of very small amounts (0.1-500 ppm) of some molecules. An assortment of such molecules could be used to ''tag'' blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ''electronic noses'' could be used to assess its characteristics in real time. It was found that the Cyranose 320{trademark}, a commercially available odor sensor, can easily distinguish among samples of rock marked with almond, cinnamon, citronella, lemon, and orange oils. Further, the sensor could detect mixtures of rocks marked with various combinations of these oils. Treatment of mixtures of galena and silica with odorant compounds showed no detrimental effects on flotation response in laboratory tests. Additional work is recommended to determine how this concept can be extended to the marking of large volumes of materials.« less

Nuclear facility decommissioning and site remedial actions: A selected bibliography, volume 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owen, P.T.; Knox, N.P.; Michelson, D.C.

1988-09-01

The 604 abstracted references on nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the ninth in a series of reports prepared annually for the US Department of Energy's Remedial Action Programs. Foreign and domestic literature of all types--technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions--has been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of Energy's remedial action programs. Major sections are (1) Surplus Facilities Management Program, (2) Nuclear Facilities Decommissioning, (3) Formerly Utilized Sites Remedial Action Program, (4) Facilitiesmore » Contaminated with Naturally Occurring Radionuclides, (5) Uranium Mill Tailings Remedial Action Program, (6) Uranium Mill Tailings Management, (7) Technical Measurements Center, and (8) General Remedial Action Program Studies. Subsections for sections 1, 2, 5, and 6 include: Design, Planning, and Regulations; Environmental Studies and Site Surveys; Health, Safety, and Biomedical Studies; Decontamination Studies; Dismantlement and Demolition; Site Stabilization and Reclamation; Waste Disposal; Remedial Action Experience; and General Studies. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication description. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, and keywords. This report is a product of the Remedial Action Program Information Center (RAPIC), which selects and analyzes information on remedial actions and relevant radioactive waste management technologies. RAPIC staff and resources are available to meet a variety of information needs. Contact the center at (615) 576-0568 or FTS 626-0568.« less

Russian Experience in the Regulatory Supervision of the Uranium Legacy Sites - 12441

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiselev, M.F.; Romanov, V.V.; Shandala, N.K.

2012-07-01

Management of the uranium legacy is accompanied with environmental impact intensity of which depends on the amount of the waste generated, the extent of that waste localization and environmental spreading. The question is: how hazardous is such impact on the environment and human health? The criterion for safety assurance is adequate regulation of the uranium legacy. Since the establishment of the uranium industry, the well done regulatory system operates in the FMBA of Russia. Such system covers inter alia, the uranium legacy. This system includes the extent laboratory network of independent control and supervision, scientific researches, regulative practices. The currentmore » Russian normative and legal basis of the regulation and its application practice has a number of problems relating to the uranium legacy, connected firstly with the environmental remediation. To improve the regulatory system, the urgent tasks are: -To introduce the existing exposure situation into the national laws and standards in compliance with the ICRP system. - To develop criteria for site remediation and return, by stages, to uncontrolled uses. The similar criteria have been developed within the Russian-Norwegian cooperation for the purpose of remediation of the sites for temporary storage of SNF and RW. - To consider possibilities and methods of optimization for the remediation strategies under development. - To separate the special category - RW resulted from uranium ore mining and dressing. The current Russian RW classification is based on the waste subdivision in terms of the specific activities. Having in mind the new RW-specific law, we receive the opportunity to separate some special category - RW originated from the uranium mining and milling. Introduction of such category can simplify significantly the situation with management of waste of uranium mining and milling processes. Such approach is implemented in many countries and approved by IAEA. The category of 'RW originated from uranium mining and milling' is to be introduced as the legal acts and regulatory documents. The recent ICRP recommendations provide the flexible approaches for solving of such tasks. The FMBA of Russia recognizes the problems of radiation safety assurance related to the legacy of the former USSR in the uranium mining industry. Some part of the regulatory problems assumes to be solved within the EurAsEC inter-state target program 'Reclamation of the territories of the EurAsEC member states affected by the uranium mining and milling facilities'. Using the example of the uranium legacy sites in Kyrgyz and Tajikistan which could result in the tran-boundary disasters and require urgent reclamation, the experience will be gained to be used in other states as well. Harmonization of the national legislations and regulative documents on radiation safety assurance is envisaged. (authors)« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The 18-acre Joseph Forest Products (JFP) site is a wood-processing facility in the City of Joseph, Wallowa County, Oregon. Land use in the area is predominantly industrial and agricultural. The City of Enterprise uses two springs located 4,000 feet from JFP to serve as its municipal water supply. In 1974, and again from 1977 to 1985, Joseph Forest Products, Inc., used the site as a lumber mill, processing wood into lumber products. The selected remedial action for the site includes demolishing contaminated onsite structures, including the process, storage, and mixing tanks, and the wooden structures and concrete slabs, followed bymore » offsite disposal; decontaminating the concrete drip pad and tanks, followed by recycling or offsite disposal of debris; excavating surface and subsurface soil, with screening and segregation of hazardous waste for offsite disposal, with stabilization, if necessary, prior to disposal at appropriate facilities; backfilling any excavated areas; removing asbestos from the facility, with offsite disposal; removing underground storage tanks and any associated contaminated soil, with scrapping or offsite disposal; monitoring ground water; and implementing institutional controls, including deed and land use restrictions or environmental notices. The estimated capital cost for this remedial action is $550,000, with an annual O M cost of $24,000 for 3 years.« less

Nuclear facility decommissioning and site remedial actions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knox, N.P.; Webb, J.R.; Ferguson, S.D.

1990-09-01

The 394 abstracted references on environmental restoration, nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the eleventh in a series of reports prepared annually for the US Department of Energy's Remedial Action Programs. Citations to foreign and domestic literature of all types -- technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions -- have been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of Energy's Remedial Action Programs. Major sections are (1) Surplus Facilities Management Program, (2) Nuclear Facilities Decommissioning, (3)more » Formerly Utilized Sites Remedial Action Programs, (4) Facilities Contaminated with Naturally Occurring Radionuclides, (5) Uranium Mill Tailings Remedial Action Program, (6) Grand Junction Remedial Action Program, (7) Uranium Mill Tailings Management, (8) Technical Measurements Center, (9) Remedial Action Program, and (10) Environmental Restoration Program. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication title. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, subject category, and keywords. This report is a product of the Remedial Action Program Information Center (RAPIC), which selects and analyzes information on remedial actions and relevant radioactive waste management technologies.« less

Health assessment for Anaconda Smelter Site, Anaconda, Deer Lodge County, Montana, Region 8. CERCLIS No. MTD093291656. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-02-05

The Environmental Protection Agency (EPA,) Region VIII has requested that the Agency for Toxic Substances and Disease Registry (ATSDR) evaluate the Remedial Investigation and Feasibility Study (RI/FS) Reports for the Mill Creek, Montana Anaconda Swelter Site. Extensive environmental sampling by EPA, urinary arsenic surveys conducted by the Centers for Disease Control, the Endangerment Assessment (EA,) and the RI have consistently shown extensive contamination of soils and house dust by arsenic, cadmium, and lead, and episodic contamination of drinking water with arsenic above the EPA Maximal Contaminant Level (MCL). The RI presents results of calculations showing, potentially, an elevated excess lifetimemore » risk of skin cancer for males from chronic exposure to arsenic by ingestion. The calculations were performed only for males, the most sensitive subpopulation; however, the female subpopulation would also be expected to have a lesser but elevated excess skin cancer risk from ingestion of arsenic. The long-term health effects of cadmium and lead are additional concerns. When EPA makes a Record of Decision (ROD) for the Mill Creek site, ATSDR can more readily make a definitive statement about the adequacy of the chosen Alternative for reducing the public health risk at Mill Creek.« less

Investigation into process-induced de-aggregation of cohesive micronised API particles.

PubMed

Hoffmann, Magnus; Wray, Patrick S; Gamble, John F; Tobyn, Mike

2015-09-30

The aim of this study was to assess the impact of unit processes on the de-aggregation of a cohesive micronised API within a pharmaceutical formulation using near-infrared chemical imaging. The impact on the primary API particles was also investigated using an image-based particle characterization system with integrated Raman analysis. The blended material was shown to contain large, API rich domains which were distributed in-homogeneously across the sample, suggesting that the blending process was not aggressive enough to disperse aggregates of micronised drug particles. Cone milling, routinely used to improve the homogeneity of such cohesive formulations, was observed to substantially reduce the number and size of API rich domains; however, several smaller API domains survived the milling process. Conveyance of the cone milled formulation through the Alexanderwerk WP120 powder feed system completely dispersed all remaining aggregates. Importantly, powder feed transmission of the un-milled formulation was observed to produce an equally homogeneous API distribution. The size of the micronised primary drug particles remained unchanged during powder feed transmission. These findings provide further evidence that this powder feed system does induce shear, and is in fact better able to disperse aggregates of a cohesive micronised API within a blend than the blend-mill-blend step. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

Hardwood regeneration related to overstory shortleaf pine basal area and site index in Arkansas and eastern Oklahoma

Treesearch

Douglas J. Stevenson; Thomas B. Lynch; James M. Guldin

2007-01-01

Shortleaf pine (Pinus echinata Mill.) grows in association with many other woody species, particularly understory hardwoods, which compete with it, limiting its productivity. Along with other species, sweet-gum (Liquidambar styracifua L.) is a major competitor on better-quality sites but decreases rapidly in importance as pine site...

Bridging the gap between tribal risk perceptions and scientific decision-making for uranium legacy sites located in Native American communities

NASA Astrophysics Data System (ADS)

Joseph, C.; Waugh, W.; Glenn, E.; Chief, K.

2017-12-01

There are approximately 15,000 abandoned uranium mines (AUM) in the western United States, of which 500 AUMs are located in the Colorado Plateau Four-Corners region. Uranium mill tailings, referred to as legacy waste, compromise the largest volume of any category of radioactive waste in the nation. Today, the Department of Energy Legacy Management is responsible for long-term stewardship and maintenance of inactive uranium processing sites that have been remediated to prevent further migration and exposure of tailings to the environment and surrounding communities. In collaboration with the DOE-LM, I am investigating the impact of climate change and community adaptation on the long-term performance of disposal cell covers for uranium mill tailings located in Native American communities, as well as how these communities have adapted to and perceive these areas. I am interested in how abiotic engineered cell covers may be candidate sites for future conversion to vegetated evapotranspirative caps for arid to semi-arid climates. The objectives are to: 1) assess above-ground tissue of plants encroaching engineered cell covers for concentrations of uranium, radium, selenium, molybdenum, thorium, arsenic, lead, and manganese and compare them to control sites; 2) determine if above-cell plant tissue is accumulating to toxic levels that may create an exposure pathway, 3) identify climate scenarios for site locations and determine how short-and long-scale climate projections will influence spatial and temporal plant distribution for specific woody species; and 4) evaluate the risk perceptions of Hopi villages located five miles downstream of one site location. To date, risk perception and stakeholder outreach to the Hopi communities has been absent. This study will help inform how land use, water use, and sustenance practices may contribute to environmental health disparities for one of the few tribes that has maintained physical continuity within their ancestral homeland.

Degradation and biodegradability improvement of the olive mill wastewater by peroxi-electrocoagulation/electrooxidation-electroflotation process with bipolar aluminum electrodes.

PubMed

Esfandyari, Yahya; Mahdavi, Yousef; Seyedsalehi, Mahdi; Hoseini, Mohammad; Safari, Gholam Hossein; Ghozikali, Mohammad Ghanbari; Kamani, Hossein; Jaafari, Jalil

2015-04-01

Olive mill wastewater is considered as one of the most polluting effluents of the food industry and constitutes a source of important environmental problems. In this study, the removal of pollutants (chemical oxygen demand (COD), biochemical oxygen demand (BOD5), polyphenols, turbidity, color, total suspended solids (TSS), and oil and grease) from olive oil mill processing wastewater by peroxi-electrocoagulation/electrooxidation-electroflotation process with bipolar aluminum electrodes was evaluated using a pilot continuous reactor. In the electrochemical unit, aluminum (Al), stainless steel, and RuO2/Ti plates were used. The effects of pH, hydrogen peroxide doses, current density, NaCl concentrations, and reaction times were studied. Under optimal conditions of pH 4, current density of 40 mA/m(2), 1000 mg/L H2O2, 1 g/L NaCl, and 30-min reaction time, the peroxi-electrochemical method yielded very effective removal of organic pollution from the olive mill wastewater diluted four times. The treatment process reduced COD by 96%, BOD5 by 93.6%, total, polyphenols by 94.4%, color by 91.4%, turbidity by 88.7, suspended solids by 97% and oil and grease by 97.1%. The biodegradability index (BOD5/COD) increased from 0.29 to 0.46. Therefore, the peroxi-electrocoagulation/electrooxidation-electroflotation process is considered as an effective and feasible process for pre-treating olive mill wastewater, making possible a post-treatment of the effluent in a biological system.

Aerosol particle and organic vapor concentrations at industrial work sites in Malaysia.

PubMed

Armstrong, R W; Rood, M J; Sani, S; Mohamed, M; Rashid, M; Jab, A T; Landsberger, S

2001-01-01

The objective of this study was to establish baseline data about air pollutants potentially related to nasopharyngeal carcinoma (NPC) in the Federal Territory and Selangor, Malaysia. During 1991-1993, ambient air quality was monitored at 42 work sites representing ten industrial sectors: adhesive manufacturing, foundries, latex processing, metalworking, plywood/veneer milling, ricemilling, rubber tire manufacturing, sawmilling, shoemaking, and textile related industries. At each work site, aerosol particle size distributions and concentrations of formaldehyde, benzene, toluene, isopropyl alcohol, and furfural were measured. Mean aerosol particle concentrations ranged from 61 micrograms/m3 in foundries to 5,578 micrograms/m3 in ricemills, with five industries (adhesives, metalworking, ricemilling, sawmilling, and shoemaking) exceeding the US EPA 24-hr ambient air standard for PM-10. Formaldehyde concentrations exceeded the threshold limit value (TLV) in adhesives factories. Other vapours and elements measured were well below TLVs.

5. VIEW OF BERYLLIUM PROCESSING AREA, ROLLING MILL. BERYLLIUM FORMING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. VIEW OF BERYLLIUM PROCESSING AREA, ROLLING MILL. BERYLLIUM FORMING BEGAN IN SIDE A OF THE BUILDING IN 1962. (11/5/73) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

7 CFR 868.256 - Milling requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... FOR CERTAIN AGRICULTURAL COMMODITIES United States Standards for Brown Rice for Processing Principles....252(g)) in brown rice for processing, the degree of milling shall be equal to, or better than, that of the interpretive line sample for “well-milled” rice. [42 FR 40869, Aug. 12, 1977. Redesignated at...

7 CFR 868.256 - Milling requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... FOR CERTAIN AGRICULTURAL COMMODITIES United States Standards for Brown Rice for Processing Principles....252(g)) in brown rice for processing, the degree of milling shall be equal to, or better than, that of the interpretive line sample for “well-milled” rice. [42 FR 40869, Aug. 12, 1977. Redesignated at...

Post-processing, energy production use of sugarcane bagasse ash

USDA-ARS?s Scientific Manuscript database

Sugarcane bagasse ash (SBA) is a multi-process by-product produced from the milling of sugarcane. Bagasse is the fibrous material remaining after removing the sugar, water, and other impurities from the sugarcane delivered to the mill. Louisiana produces an estimated 2.7 mt of bagasse each year. In ...

Post-processing, energy production use of sugarcane bagasse ash

USDA-ARS?s Scientific Manuscript database

Sugarcane bagasse ash (SBA) is a multi-processed by-product produced from the milling of sugarcane. Bagasse is the fibrous material remaining after removing the sugar, water, and other impurities from the sugarcane delivered to the mill. Louisiana produces an estimated 3 million tons of bagasse each...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

Lumber defect detection abilities of furniture rough mill employees

Treesearch

Henry A. Huber; Charles W. McMillin; John P. McKinney

1985-01-01

To cut parts from boards, rough mill employees must be able to see defects, calculate the proper location of cuts, manually position the board, and remain alert. The objective of this study was to evaluate how well rough mill employees perform the task of recognizing, locating, and identifying surface defects independent of the calculation and positioning process....

Process Capability of High Speed Micro End-Milling of Inconel 718 with Minimum Quantity Lubrication

NASA Astrophysics Data System (ADS)

Rahman, Mohamed Abd; Yeakub Ali, Mohammad; Rahman Shah Rosli, Abdul; Banu, Asfana

2017-03-01

The demand for micro-parts is expected to grow and micro-machining has been shown to be a viable manufacturing process to produce these products. These micro-products may be produced from hard-to-machine materials such as superalloys under little or no metal cutting fluids to reduce machining cost or drawbacks associated with health and environment. This project aims to investigate the capability of micro end-milling process of Inconel 718 with minimum quantity lubrication (MQL). Microtools DT-110 multi-process micro machine was used to machine 10 micro-channels with MQL and 10 more under dry condition while maintaining the same machining parameters. The width of the micro-channels was measured using digital microscope and used to determine the process capability indices, Cp and Cpk. QI Macros SPC for Excel was used to analyze the resultant machining data. The results indicated that micro end-milling process of Inconel 718 was not capable under both MQL and dry cutting conditions as indicated by the Cp values of less than 1.0. However, the use of MQL helped the process to be more stable and capable. Results obtained showed that the process variation was greatly reduced by using MQL in micro end-milling of Inconel 718.

Synthesis and characterization of magnetite-maghemite nanoparticles obtained by the high-energy ball milling method

NASA Astrophysics Data System (ADS)

Velásquez, A. A.; Marín, C. C.; Urquijo, J. P.

2018-03-01

We present the process of synthesis and characterization of magnetite-maghemite nanoparticles by the ball milling method. The particles were synthesized in a planetary ball mill equipped with vials and balls of tempered steel, employing dry and wet conditions. For dry milling, we employed microstructured analytical-grade hematite (α-Fe2O3), while for wet milling, we mixed hematite and deionized water. Milling products were characterized by X-ray diffraction, transmission electron microscopy, room temperature Mössbauer spectroscopy, vibrating sample magnetometry, and atomic absorption spectroscopy. The Mössbauer spectrum of the dry milling product was well fitted with two sextets of hematite, while the spectrum of the wet milling product was well fitted with three sextets of spinel phase. X-ray measurements confirmed the phases identified by Mössbauer spectroscopy in both milling conditions and a reduction in the crystallinity of the dry milling product. TEM measurements showed that the products of dry milling for 100 h and wet milling for 24 h consist of aggregates of nanoparticles distributed in size, with mean particle size of 10 and 15 nm, respectively. Magnetization measurements of the wet milling product showed little coercivity and a saturation magnetization around 69 emu g-1, characteristic of a nano-spinel system. Atomic absorption measurements showed that the chromium contamination in the wet milling product is approximately two orders of magnitude greater than that found in the dry milling product for 24 h, indicating that the material of the milling bodies, liberated more widely in wet conditions, plays an important role in the conversion hematite-spinel phase.

Nanofabrication and ion milling introduced effects on magnetic properties in magnetic recording

NASA Astrophysics Data System (ADS)

Sun, Zhenzhong

Perpendicular magnetic nanostructures have played an important role in magnetic recording technologies. In this dissertation, a systematic study on the CoPt magnetic nanostructures from fabrication, characterization to computer simulation has been performed. During the fabrication process, ion irradiation/bombardment in ion mill can cause physical damage to the magnetic nanostructures and degrade their magnetic properties. To study the effect of ion damage on CoPt nanostructures, different degrees of ion damage are introduced into CoPt nanopillars by varying the accelerating voltage in ion mill. The results demonstrate that the ion damage can reduce the coercivity by softening circumferential edge, and therefore changes the switching mechanism from coherent rotation to nucleation followed by rapid domain wall propagation. The SFD of CoPt nanostructures is independent of ion damage and is mainly determined by the intrinsic anisotropy distribution of the film rather than the nanostructure size distribution. Anisotropy-graded bit-patterned media are fabricated and studied based on high anisotropy L10-FePt material system. L10-FePt thin films with linearly and quadratically distributed anisotropy are achieved by varying substrate temperature during film growth. After patterning, the anisotropy-graded L10-FePt nanopillars display a reduced switching field and maintain a good thermal stability compared to the non-graded one. Experimental investigation and comparison further prove the concept of "anisotropy-graded" bit-patterned media and their potential application in the future magnetic recording. During magnetic write head fabrication, ion-beam damage may degrade the performance of the magnetic write pole. A surface sensitive MOKE is used to characterize the magnetic properties of these etched FeCo films. MOKE measurement shows a hard axis hysteresis loop with a high Mr in the high power etched film due to the ion beam introduced defects. The high power etched film also shows the highest RMS by AFM measurement. The geometric peaks at the top surface may have shape anisotropy and serve as the pinning sites. These magnetic pinning sites can prevent the nucleation center forming at the top surface during the switching process and lead to a high Mr in the top surface region.

Improved oral bioavailability of probucol by dry media-milling.

PubMed

Li, Jia; Yang, Yan; Zhao, Meihui; Xu, Hui; Ma, Junyuan; Wang, Shaoning

2017-09-01

The polymer/probucol co-milled mixtures were prepared to improve drug dissolution rate and oral bioavailability. Probucol, a BCS II drug, was co-milled together with Copovidone (Kollidon VA64, VA64), Soluplus, or MCC using the dry media-milling process with planetary ball-milling equipment. The properties of the milled mixtures including morphology, crystal form, vitro drug dissolution and in vivo oral bioavailability in rats were evaluated. Probucol existed as an amorphous in the matrix of the co-milled mixtures containing VA64, which helped to enhance drug dissolution. The ternary mixture composed of VA64, RH40, and probucol showed increased dissolution rates in both sink and non-sink conditions. It also had a higher oral bioavailability compared to the reference formulation. Dry-media milling of binary or ternary mixtures composed of drug, polymer and surfactant possibly have wide applications to improve dissolution rate and oral bioavailability of water-insoluble drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of machining accuracy during free form surface milling simulation for different milling strategies

NASA Astrophysics Data System (ADS)

Matras, A.; Kowalczyk, R.

2014-11-01

The analysis results of machining accuracy after the free form surface milling simulations (based on machining EN AW- 7075 alloys) for different machining strategies (Level Z, Radial, Square, Circular) are presented in the work. Particular milling simulations were performed using CAD/CAM Esprit software. The accuracy of obtained allowance is defined as a difference between the theoretical surface of work piece element (the surface designed in CAD software) and the machined surface after a milling simulation. The difference between two surfaces describes a value of roughness, which is as the result of tool shape mapping on the machined surface. Accuracy of the left allowance notifies in direct way a surface quality after the finish machining. Described methodology of usage CAD/CAM software can to let improve a time design of machining process for a free form surface milling by a 5-axis CNC milling machine with omitting to perform the item on a milling machine in order to measure the machining accuracy for the selected strategies and cutting data.

Role of Sample Processing Strategies at the European Union National Reference Laboratories (NRLs) Concerning the Analysis of Pesticide Residues.

PubMed

Hajeb, Parvaneh; Herrmann, Susan S; Poulsen, Mette E

2017-07-19

The guidance document SANTE 11945/2015 recommends that cereal samples be milled to a particle size preferably smaller than 1.0 mm and that extensive heating of the samples should be avoided. The aim of the present study was therefore to investigate the differences in milling procedures, obtained particle size distributions, and the resulting pesticide residue recovery when cereal samples were milled at the European Union National Reference Laboratories (NRLs) with their routine milling procedures. A total of 23 NRLs participated in the study. The oat and rye samples milled by each NRL were sent to the European Union Reference Laboratory on Cereals and Feedingstuff (EURL) for the determination of the particle size distribution and pesticide residue recovery. The results showed that the NRLs used several different brands and types of mills. Large variations in the particle size distributions and pesticide extraction efficiencies were observed even between samples milled by the same type of mill.

A study of processing parameters in thermal-sprayed alumina and zircon mixtures

NASA Astrophysics Data System (ADS)

Li, Y.; Khor, K. A.

2002-06-01

A method of plasma spraying of alumina and zircon mixtures to form ZrO2-mullite composites has been proposed and developed. The feedstock is prepared by a combination of mechanical alloying, which allows formation of fine-grained, homogeneous solid-solution mixtures, followed by plasma spheroidization that yields rapid solidified microstructures and enhanced compositional homogeneity. The effects of ball-milling duration and milling media were studied. It was found that zirconia is a more efficient milling media and that increasing milling duration enhanced the dissociation of zircon. Flame spray and plasma spray processes were used to spheroidize the spray-dried powders. The temperature of the flame spray was found to be insufficient to melt the powders completely. The processing parameters of the plasma spray played an important role in zircon decomposition and mullite formation. Increasing the arc current or reducing secondary gas pressure caused more zircon to decompose and more mullite to form after heat treatment at 1200 °C for 3 h. Dissociation of zircon and the amount of mullite for med can be enhanced significantly when using the more efficient, computerized plasma-spraying system and increasing the ball-milling duration from 4 to 8 h.

Toward the complete utilization of rice straw: Methane fermentation and lignin recovery by a combinational process involving mechanical milling, supporting material and nanofiltration.

PubMed

Sasaki, Kengo; Okamoto, Mami; Shirai, Tomokazu; Tsuge, Yota; Fujino, Ayami; Sasaki, Daisuke; Morita, Masahiko; Matsuda, Fumio; Kikuchi, Jun; Kondo, Akihiko

2016-09-01

Rice straw was mechanically milled using a process consuming 1.9MJ/kg-biomass, and 10g/L of unmilled or milled rice straw was used as the carbon source for methane fermentation in a digester containing carbon fiber textile as the supporting material. Milling increased methane production from 226 to 419mL/L/day at an organic loading rate of 2180mg-dichromate chemical oxygen demand/L/day, corresponding to 260mLCH4/gVS. Storage of the fermentation effluent at room temperature decreased the weight of the milled rice straw residue from 3.81 to 1.00g/L. The supernatant of the effluent was subjected to nanofiltration. The black concentrates deposited on the nanofiltration membranes contained 53.0-57.9% lignin. Solution nuclear magnetic resonance showed that lignin aromatic components such as p-hydroxyphenyl (H), guaiacyl (G), and syringyl (S) were retained primarily, and major lignin interunit structures such as the β-O-4-H/G unit were absent. This combinational process will aid the complete utilization of rice straw. Copyright © 2016. Published by Elsevier Ltd.

Bioplastic production using wood mill effluents as feedstock.

PubMed

Ben, M; Mato, T; Lopez, A; Vila, M; Kennes, C; Veiga, M C

2011-01-01

Fibreboard production is one of the most important industrial activities in Galicia (Spain). Great amounts of wastewater are generated, with properties depending on the type of wood, treatment process, final product and water reusing, among others. These effluents are characterized by a high chemical oxygen demand, low pH and nutrients limitation. Although anaerobic digestion is one of the most suitable processes for the treatment, lately bioplastics production (mainly polyhydroxyalkanoates) from wastewaters with mixed cultures is being evaluated. Substrate requirements for these processes consist of high organic matter content and low nutrient concentration. Therefore, wood mill effluents could be a suitable feedstock. In this work, the possibility of producing bioplastics from to wood mill effluents is evaluated. First, wood mill effluent was converted to volatile fatty acids in an acidogenic reactor operated at two different hydraulic retention times of 1 and 1.5 d. The acidification percentage obtained was 37% and 42%, respectively. Then, aerobic batch assays were performed using fermented wood mill effluents obtained at different hydraulic retention times. Assays were developed using different cultures as inoculums. The maximum storage yield of 0.57 Cmmol/Cmmol was obtained when when the culture was enriched on a synthetic media.

Scale-up of organic reactions in ball mills: process intensification with regard to energy efficiency and economy of scale.

PubMed

Stolle, Achim; Schmidt, Robert; Jacob, Katharina

2014-01-01

The scale-up of the Knoevenagel-condensation between vanillin and barbituric acid carried out in planetary ball mills is investigated from an engineering perspective. Generally, the reaction proceeded in the solid state without intermediate melting and afforded selectively only one product. The reaction has been used as a model to analyze the influence and relationship of different parameters related to operation in planetary ball mills. From the viewpoint of technological parameters the milling ball diameter, dMB, the filling degree with respect to the milling balls' packing, ΦMB,packing, and the filling degree of the substrates with respect to the void volume of the milling balls' packing, ΦGS, have been investigated at different reaction scales. It was found that milling balls with small dMB lead to higher yields within shorter reaction time, treaction, or lower rotation frequency, rpm. Thus, the lower limit is set considering the technology which is available for the separation of the milling balls from the product after the reaction. Regarding ΦMB,packing, results indicate that the optimal value is roughly 50% of the total milling beakers' volume, VB,total, independent of the reaction scale or reaction conditions. Thus, 30% of VB,total are taken by the milling balls. Increase of the initial batch sizes changes ΦGS significantly. However, within the investigated parameter range no negative influence on the yield was observed. Up to 50% of VB,total can be taken over by the substrates in addition to 30% for the total milling ball volume. Scale-up factors of 15 and 11 were realized considering the amount of substrates and the reactor volume, respectively. Beside technological parameters, variables which influence the process itself, treaction and rpm, were investigated also. Variation of those allowed to fine-tune the reaction conditions in order to maximize the yield and minimize the energy intensity.

Peculiarities of binding composition production in vortex jet mill

NASA Astrophysics Data System (ADS)

Zagorodnyuk, L. Kh; Lesovik, V. S.; Sumskoy, D. A.; Elistratkin, M. Yu; Makhortov, D. S.

2018-03-01

The article investigates the disintegration of perlite production waste in a vortex jet mill; the regularities of milling were established. Binding compositions were obtained at different ratios of cement vs. perlite sand production waste in the vortex jet mill in various milling regimes. The peculiarities of milling processes were studied, and technological and physicomechanical properties of the binding compositions were determined as well. The microstructure of the cement stones made of activated Portland cement and binding compositions in the vortex jet mill was elucidated by electron microscopy. The open pores of the cement-binding compositions prepared using perlite fillers were found to be filled by newgrowths at different stages of collective growth. The microstructure of the binding compositions is dense due to rationally proportioned composition, effective mineral filler— perlite waste — that creates additional substrates for internal composite microstructure formation, mechanochemical activation of raw mixture, which allows obtaining composites with required properties.

Mechanochemical stabilization and sintering of nanocrystalline the (ZrO2)0.97 (Y2O3)0.03 solid solution from pure oxides

NASA Astrophysics Data System (ADS)

Rendtorff, N. M.; Suárez, G.; Sakka, Y.; Aglietti, E. F.

2011-10-01

The mechanochemical activation processing has proved to be an effective technique to enhance a solid-state reaction at relatively low temperatures. In such a process, the mechanical effects of milling, such as reduction of particle size and mixture homogenization, are accompanied by chemical effects, such as partial decomposition of salts or hydroxides resulting in very active reactants. The objective of the present work is to obtain (ZrO2)0.97(Y2O3)0.03 nanocrystalline tetragonal solid solution powders directly using a high energy milling on a mixture of the pure oxides. A second objective is to evaluate the efficiency of the processing proposed and to characterize both textural and structural evolution of the mixtures during the milling processes and throughout posterior low temperature treatments. The Textural and structural evolution were studied by XRD analysis, specific area measurements (BET) and SEM. Firstly a decrease of the crystallinity of the reactants was observed, followed by the disappearance of Y2O3 diffraction peaks and the partial appearance of the tetragonal phase at room temperature. The solid solution proportion was increased with the high energy milling time, obtaining complete stabilization of the tetragonal solid solution with long milling treatments (60 min).The obtained powders were uniaxially pressed and sintered at different temperatures (600-1400°C) the influence of the milling time was correlated with the sinterization degree and final crystalline composition of the materials. Finally, fully stabilized nanocrystalline zirconia materials were obtained satisfactorily by the proposed method.

An Intensified Vibratory Milling Process for Enhancing the Breakage Kinetics during the Preparation of Drug Nanosuspensions.

PubMed

Li, Meng; Zhang, Lu; Davé, Rajesh N; Bilgili, Ecevit

2016-04-01

As a drug-sparing approach in early development, vibratory milling has been used for the preparation of nanosuspensions of poorly water-soluble drugs. The aim of this study was to intensify this process through a systematic increase in vibration intensity and bead loading with the optimal bead size for faster production. Griseofulvin, a poorly water-soluble drug, was wet-milled using yttrium-stabilized zirconia beads with sizes ranging from 50 to 1500 μm at low power density (0.87 W/g). Then, this process was intensified with the optimal bead size by sequentially increasing vibration intensity and bead loading. Additional experiments with several bead sizes were performed at high power density (16 W/g), and the results were compared to those from wet stirred media milling. Laser diffraction, scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, and dissolution tests were used for characterization. Results for the low power density indicated 800 μm as the optimal bead size which led to a median size of 545 nm with more than 10% of the drug particles greater than 1.8 μm albeit the fastest breakage. An increase in either vibration intensity or bead loading resulted in faster breakage. The most intensified process led to 90% of the particles being smaller than 300 nm. At the high power intensity, 400 μm beads were optimal, which enhanced griseofulvin dissolution significantly and signified the importance of bead size in view of the power density. Only the optimally intensified vibratory milling led to a comparable nanosuspension to that prepared by the stirred media milling.

Mechanochemical processing for metals and metal alloys

DOEpatents

Froes, Francis H.; Eranezhuth, Baburaj G.; Prisbrey, Keith

2001-01-01

A set of processes for preparing metal powders, including metal alloy powders, by ambient temperature reduction of a reducible metal compound by a reactive metal or metal hydride through mechanochemical processing. The reduction process includes milling reactants to induce and complete the reduction reaction. The preferred reducing agents include magnesium and calcium hydride powders. A process of pre-milling magnesium as a reducing agent to increase the activity of the magnesium has been established as one part of the invention.

44. View of Botany Worsted Mills looking southeast along Dayton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. View of Botany Worsted Mills looking southeast along Dayton Avenue; building No. 2 at left, building No. 4 rising at center, building No. 68-69 at end of avenue; site of 95-97 Dayton Avenue and other former Botany buildings at right - Dundee Canal Industrial Historic District, Beginning at George Street in Passaic & extending north along Dundee Canal approximately 1.2 miles to Canal headgates opposite East Clifton Avenue in Clifton, Passaic, Passaic County, NJ

STABLE GENETIC STRUCTURE OF CENTRAL STONEROLLER POPULATIONS IN A POLLUTED URBAN STREAM

EPA Science Inventory

Mill Creek, which runs through Cincinnati, Ohio, is one of the most severely polluted urban streams in the United States. The creek is threatened by streamside landfills and toxic waste sites along the streams banks (including five designated superfund sites), industrial and res...

Hardwoods on pine sites: competition or antagonistic symbiosis

Treesearch

Michael D. Cain

1990-01-01

Early development of natural loblolly (Pinus taeda L.) and shortleaf pine (Pinus echinata Mill.) regeneration was monitored in two research studies and two research demonstrations between 1980 and I989 in southern Arkansas. Site preparation and hardwood control incorporated the use of herbicides, mechanical treatments, or...

Uptake of uranium by aquatic plants growing in fresh water ecosystem around uranium mill tailings pond at Jaduguda, India.

PubMed

Jha, V N; Tripathi, R M; Sethy, N K; Sahoo, S K

2016-01-01

Concentration of uranium was determined in aquatic plants and substrate (sediment or water) of fresh water ecosystem on and around uranium mill tailings pond at Jaduguda, India. Aquatic plant/substrate concentration ratios (CRs) of uranium were estimated for different sites on and around the uranium mill tailings disposal area. These sites include upstream and downstream side of surface water sources carrying the treated tailings effluent, a small pond inside tailings disposal area and residual water of this area. Three types of plant groups were investigated namely algae (filamentous and non-filamentous), other free floating & water submerged and sediment rooted plants. Wide variability in concentration ratio was observed for different groups of plants studied. The filamentous algae uranium concentration was significantly correlated with that of water (r=0.86, p<0.003). For sediment rooted plants significant correlation was found between uranium concentration in plant and the substrate (r=0.88, p<0.001). Both for other free floating species and sediment rooted plants, uranium concentration was significantly correlated with Mn, Fe, and Ni concentration of plants (p<0.01). Filamentous algae, Jussiaea and Pistia owing to their high bioproductivity, biomass, uranium accumulation and concentration ratio can be useful for prospecting phytoremediation of stream carrying treated or untreated uranium mill tailings effluent. Copyright © 2015 Elsevier B.V. All rights reserved.

OVERVIEW OF REMAINS OF DEWATERING BUILDING, LOOKING SOUTH TOWARD CYANIDE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERVIEW OF REMAINS OF DEWATERING BUILDING, LOOKING SOUTH TOWARD CYANIDE PROCESSING AREA. WATER USED IN PROCESSING AT THE STAMP MILL WAS CIRCULATED HERE FOR RECLAMATION. SANDS WERE SETTLED OUT AND DEPOSITED IN ONE OF TWO TAILINGS HOLDING AREAS. CLEARED WATER WAS PUMPED BACK TO THE MILL FOR REUSE. THIS PROCESS WAS ACCOMPLISHED BY THE USE OF SETTLING CONES, EIGHT FEET IN DIAMETER AND SIX FEET HIGH. THE REMAINS OF FOUR CONES ARE AT CENTER, BEHIND THE TANK IN THE FOREGROUND. TO THE LEFT IS THE MAIN ACCESS ROAD BETWEEN THE MILL AND THE PARKING LOT. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Structure and magnetic properties of mechanically alloyed Co and Co-Ni

NASA Astrophysics Data System (ADS)

Guessasma, S.; Fenineche, N.

The influence of milling process on magnetic properties of Co and Co-Ni materials is studied. Coercivity, squareness ratio and crystallite size of mechanically alloyed Co-Ni material were related to milling time. For Co material, coercivity, cubic phase ratio and crystallite size were related to milling energy considering the vial and plateau rotation velocities. An artificial neural network (ANN) combining the parameters for both materials is used to predict magnetic and structure results versus milling conditions. Predicted results showed that milling energy is mostly dependent on the ratio vial to plateau rotation velocities and that milling times larger than 40 h do not add significant change to both structure and magnetic responses. Magnetic parameters were correlated to crystallite size and the D 6 law was only valid for small sizes.

Long-term surveillance plan for the Bodo Canyon Disposal Site, Durango, Colorado. Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-11-01

This long-term surveillance plan (LTSP) for the Uranium Mill Tailings Remedial Act on (UMTRA) Project Bodo Canyon disposal site at Durango, Colorado, describes the surveillance activities for the disposal site. The US Department of Energy (DOE) will carry out these activities to ensure that the disposal call continues to function as designed This LTSP was prepared as a requirement for DOE acceptance under the US Nuclear Regulatory Commission (NRC) general license for custody and long-term care of residual radioactive materials (RRM) from processing uranium ore. This LTSP documents that the land and interests are owned by the United States andmore » details how long-term care of the disposal site will be carried out. It is based on the DOE`s Guidance for Implementing the UMTRA Project Long-term Surveillance Program (DOE, 1992a). Following the introduction, contents of this report include the following: site final condition; site drawings and photographs; permanent site surveillance features; ground water monitoring; annual site inspections; unscheduled inspections; custodial maintenance; corrective action; record keeping and reporting requirements; emergency notification and reporting; quality assurance; personal health and safety; list of contributions; and references.« less

Forest products industries of the southern Middle-Atlantic states, 1985 - 1986

Treesearch

Eric H. Wharton; Kevin Mullarkey; Kevin Mullarkey

1993-01-01

Evaluates regional timber output of Maryland, Delaware, and New Jersey. Results are based on a survey of primary processing mills located in these states and of mills in other states that used wood from the region. Contains statistics on industrial timber production and mill receipts and the production and final end use of manufacturing residues. Comparisons are made...

Spray drying of a phenolic-rich membrane filtration fraction of olive mill wastewater: Optimization and dried product quality

USDA-ARS?s Scientific Manuscript database

Olive mill wastewater (OMWW) from two California mills (3-phase and 2-phase) was subjected to a two-step membrane filtration process using a novel vibratory system. The obtained reverse osmosis retentate (RO-R) is a phenolic-rich co-product stream, and the reverse osmosis permeate is a near-pure wat...

Resolving the pulpwood canvass with inventory harvest information

Treesearch

Joseph M. McCollum; Tony G. Johnson

2012-01-01

The Resource Use section of the Forest Inventory and Analysis (FIA) Program has done a canvas of wood processing mills for timber product output (TPO) throughout the southern United States. Pulpmills in the South are canvassed on an annual basis, while all other mills (e.g., sawmills, veneer mills, etc.) are canvassed every two years. Attempts have been made to graph...

Role of tool marks inside spherical mitigation pit fabricated by micro-milling on repairing quality of damaged KH2PO4 crystal

PubMed Central

Chen, Ming-Jun; Cheng, Jian; Yuan, Xiao-Dong; Liao, Wei; Wang, Hai-Jun; Wang, Jing-He; Xiao, Yong; Li, Ming-Quan

2015-01-01

Repairing initial slight damage site into stable structures by engineering techniques is the leading strategy to mitigate the damage growth on large-size components used in laser-driven fusion facilities. For KH2PO4 crystals, serving as frequency converter and optoelectronic switch-Pockels cell, micro-milling has been proven the most promising method to fabricate these stable structures. However, tool marks inside repairing pit would be unavoidably introduced due to the wearing of milling cutter in actual repairing process. Here we quantitatively investigate the effect of tool marks on repairing quality of damaged crystal components by simulating its induced light intensification and testing the laser-induced damage threshold. We found that due to the formation of focusing hot spots and interference ripples, the light intensity is strongly enhanced with the presence of tool marks, especially for those on rear surfaces. Besides, the negative effect of tool marks is mark density dependent and multiple tool marks would aggravate the light intensification. Laser damage tests verified the role of tool marks as weak points, reducing the repairing quality. This work offers new criterion to comprehensively evaluate the quality of repaired optical surfaces to alleviate the bottleneck issue of low laser damage threshold for optical components in laser-driven fusion facilities. PMID:26399624

Influence of soil site class on growth and decay of northern white-cedar and two associates in Maine

Treesearch

P.V. Hofmeyer; R.S. Seymour; L.S. Kenefic

2009-01-01

Basal area growth of outwardly sound northern white-cedar (Thuja occidentalis L.) was compared with that of balsam fir (Abies balsamea [L.] Mill.) and red spruce (Picea rubens Sarg.) across site and light exposure class gradients on 60 sites throughout northern Maine. Once adjusted for sapwood area,...

Remedial action plan and site design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado. Volume 5, Addenda D6--D8 to Appendix D: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-02-01

This volume contains appendices D6 through D8 containing laboratory test data: from MK-F investigation, 1987, Old Rifle and New Rifle sites; on bentonite amended radon barrier material; and from MK-F investigation, 1987, riprap tests.

Furniture rough mill costs evaluated by computer simulation

Treesearch

R. Bruce Anderson

1983-01-01

A crosscut-first furniture rough mill was simulated to evaluate processing and raw material costs on an individual part basis. Distributions representing the real-world characteristics of lumber, equipment feed speeds, and processing requirements are programed into the simulation. Costs of parts from a specific cutting bill are given, and effects of lumber input costs...

Quality control troubleshooting tools for the mill floor

Treesearch

John Dramm

2000-01-01

Statistical Process Control (SPC) provides effective tools for improving process quality in the forest products industry resulting in reduced costs and improved productivity. Implementing SPC helps identify and locate problems that occur in wood products manufacturing. SPC tools achieve their real value when applied on the mill floor for monitoring and troubleshooting...

Effect of processing methods on the mechanical properties of natural rubber filled with stearic acid modified soy protein particles

USDA-ARS?s Scientific Manuscript database

Natural rubber was reinforced with stearic acid modified soy protein particles prepared with a microfluidizing and ball milling process. Longer ball milling time tends to increase tensile strength of the rubber composites. Elastic modulus of the composites increased with the increasing filler concen...

[Study on two preparation methods for beta-CD inclusion compound of four traditional Chinese medicine volatile oils].

PubMed

Li, Hailiang; Cui, Xiaoli; Tong, Yan; Gong, Muxin

2012-04-01

To compare inclusion effects and process conditions of two preparation methods-colloid mill and saturated solution-for beta-CD inclusion compound of four traditional Chinese medicine volatile oils and study the relationship between each process condition and volatile oil physical properties and the regularity of selective inclusion of volatile oil components. Volatile oils from Nardostachyos Radix et Rhizoma, Amomi Fructus, Zingiberis Rhizoma and Angelicaesinensis Radix were prepared using two methods in the orthogonal test. These inclusion compounds by optimized processes were assessed and compared by such methods as TLC, IR and scanning electron microscope. Inclusion oils were extracted by steam distillation, and the components found before and after inclusion were analyzed by GC-MS. Analysis showed that new inclusion compounds, but inclusion compounds prepared by the two processes had differences to some extent. The colloid mill method showed a better inclusion effect than the saturated solution method, indicating that their process conditions had relations with volatile oil physical properties. There were differences in the inclusion selectivity of components between each other. The colloid mill method for inclusion preparation is more suitable for industrial requirements. To prepare volatile oil inclusion compounds with heavy gravity and high refractive index, the colloid mill method needs longer time and more water, while the saturated solution method requires higher temperature and more beta-cyclodextrin. The inclusion complex prepared with the colloid mill method contains extended molecular weight chemical composition, but the kinds of components are reduced.

Powder metallurgy preparation of Mg-Ca alloy for biodegradable implant application

NASA Astrophysics Data System (ADS)

Annur, D.; Suhardi, A.; Amal, M. I.; Anwar, M. S.; Kartika, I.

2017-04-01

Magnesium and its alloys is a promising candidate for implant application especially due to its biodegradability. In this study, Mg-7Ca alloys (in weight %) were processed by powder metallurgy from pure magnesium powder and calcium granule. Milling process was done in a shaker mill using stainless steel balls in various milling time (3, 5, and 8 hours) followed by compaction and sintering process. Different sintering temperatures were used (450°C and 550°C) to examine the effect of sintering temperature on mechanical properties and corrosion resistance. Microstructure evaluation was characterized by X-ray diffraction, scanning electron microscope and energy dispersive X-ray spectroscopy. Mechanical properties and corrosion behavior were examined through hardness testing and electrochemical testing in Hank’s solution (simulation body fluid). In this report, a prolonged milling time reduced particle size and later affected mechanical properties of Mg alloy. Meanwhile, the phase analysis showed that α Mg, Mg2Ca, MgO phases were formed after the sintering process. Further, this study showed that Mg-Ca alloy with different powder metallurgy process would have different corrosion rate although there were no difference of Ca content in the alloy.

An integrated condition-monitoring method for a milling process using reduced decomposition features

NASA Astrophysics Data System (ADS)

Liu, Jie; Wu, Bo; Wang, Yan; Hu, Youmin

2017-08-01

Complex and non-stationary cutting chatter affects productivity and quality in the milling process. Developing an effective condition-monitoring approach is critical to accurately identify cutting chatter. In this paper, an integrated condition-monitoring method is proposed, where reduced features are used to efficiently recognize and classify machine states in the milling process. In the proposed method, vibration signals are decomposed into multiple modes with variational mode decomposition, and Shannon power spectral entropy is calculated to extract features from the decomposed signals. Principal component analysis is adopted to reduce feature size and computational cost. With the extracted feature information, the probabilistic neural network model is used to recognize and classify the machine states, including stable, transition, and chatter states. Experimental studies are conducted, and results show that the proposed method can effectively detect cutting chatter during different milling operation conditions. This monitoring method is also efficient enough to satisfy fast machine state recognition and classification.

Toward a better understanding of the lignin isolation process from wood.

PubMed

Guerra, Anderson; Filpponen, Ilari; Lucia, Lucian A; Saquing, Carl; Baumberger, Stephanie; Argyropoulos, Dimitris S

2006-08-09

The recently developed protocol for isolating enzymatic mild acidolysis lignins (EMAL) coupled with the novel combination of derivatization followed by reductive cleavage (DFRC) and quantitative (31)P NMR spectroscopy were used to better understand the lignin isolation process from wood. The EMAL protocol is shown to offer access at lignin samples that are more representative of the overall lignin present in milled wood. The combination of DFRC/(31)P NMR provided a detailed picture on the effects of the isolation conditions on the lignin structure. More specifically, we have used vibratory and ball milling as the two methods of wood pulverization and have compared their effects on the lignin structures and molecular weights. Vibratory-milling conditions cause substantial lignin depolymerization. Lignin depolymerization occurs via the cleavage of uncondensed beta-aryl ether linkages, while condensed beta-aryl ethers and dibenzodioxocins were found to be resistant to such mechanical action. Condensation and side chain oxidations were induced mechanochemically under vibratory-milling conditions as evidenced by the increased amounts of condensed phenolic hydroxyl and carboxylic acid groups. Alternatively, the mild mechanical treatment offered by ball milling was found not to affect the isolated lignin macromolecular structure. However, the overall lignin yields were found to be compromised when the mechanical action was less intense, necessitating longer milling times under ball-milling conditions. As compared to other lignin preparations isolated from the same batch of milled wood, the yield of EMAL was about four times greater than the corresponding milled wood lignin (MWL) and about two times greater as compared to cellulolytic enzyme lignin (CEL). Molecular weight distribution analyses also pointed out that the EMAL protocol allows the isolation of lignin fractions that are not accessed by any other lignin isolation procedures.

Discrete element method based scale-up model for material synthesis using ball milling

NASA Astrophysics Data System (ADS)

Santhanam, Priya Radhi

Mechanical milling is a widely used technique for powder processing in various areas. In this work, a scale-up model for describing this ball milling process is developed. The thesis is a combination of experimental and modeling efforts. Initially, Discrete Element Model (DEM) is used to describe energy transfer from milling tools to the milled powder for shaker, planetary, and attritor mills. The rolling and static friction coefficients are determined experimentally. Computations predict a quasisteady rate of energy dissipation, E d, for each experimental configuration. It is proposed that the milling dose defined as a product of Ed and milling time, t, divided by the mass of milled powder, mp characterizes the milling progress independently of the milling device or milling conditions used. Once the milling dose is determined for one experimental configuration, it can be used to predict the milling time required to prepare the same material in any milling configuration, for which Ed is calculated. The concept is validated experimentally for DEM describing planetary and shaker mills. For attritor, the predicted Ed includes substantial contribution from milling tool interaction events with abnormally high forces (>103 N). The energy in such events is likely dissipated to heat or plastically deform milling tools rather than refine material. Indeed, DEM predictions for the attritor correlate with experiments when such events are ignored in the analysis. With an objective of obtaining real-time indicators of milling progress, power, torque, and rotation speed of the impeller of an attritor mill are measured during preparation of metal matrix composite powders in the subsequent portion of this thesis. Two material systems are selected and comparisons made between in-situ parameters and experimental milling progress indicators. It is established that real-time measurements can certainly be used to describe milling progress. However, they need to be interpreted carefully depending on hardness of brittle component relative to milling media. To improve the DEM model of the attritor mill, it is desired to avoid the removal of unrealistic, high-force events using an approach that would not predict such events in the first place. It is observed that during experiments in attritor, balls may jam causing an increased resistance to the impeller's rotation. The impeller may instantaneously slow down, quickly returning to its pre-set rotation rate. Previous DEM models did not account for such rapid changes in the impeller's rotation. In this work, this relationship between impeller's torque and rotation rate is obtained experimentally and introduced in DEM. As a result, predicted Ed, are shown to correlate well with the experimental data. Finally, a methodology is proposed combining an experiment and its DEM description enabling one to identify the appropriate interaction parameters for powder systems. The experiment uses a miniature vibrating hopper and can be applied to characterize the powder flow for variety of materials. The hopper is designed to hold up to 20,000 particles of 50-mum diameter, which can be directly described in DEM. Based on comparison of discharge rate from experiments and model, all 6 interaction parameters were analyzed and the ideal conditions identified for Zirconia beads. The values of these parameters for powders are generally not the same as those established for macroscopic bodies. In addition, effects of some other experimental parameters such as particle size distribution and amplitude of vibration are also investigated.

Solid state amorphization in the Al-Fe binary system during high energy milling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Urban, P., E-mail: purban@us.es; Montes, J. M.; Cintas, J.

2013-12-16

In the present study, mechanical alloying (MA) of Al75Fe25 elemental powders mixture was carried out in argon atmosphere, using a high energy attritor ball mill. The microstructure of the milled products at different stages of milling was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The results showed that the amorphous phase content increased by increasing the milling time, and after 50 hours the amorphization process became complete. Heating the samples resulted in the crystallization of the synthesized amorphous alloys and the appearance of the equilibrium intermetallic compounds Al{sub 5}Fe{submore » 2}.« less

Associations between urinary biomarkers of oxidative stress and air pollutants observed in a randomized crossover exposure to steel mill emissions.

PubMed

Pelletier, Guillaume; Rigden, Marc; Kauri, Lisa Marie; Shutt, Robin; Mahmud, Mamun; Cakmak, Sabit; Kumarathasan, Premkumari; Thomson, Errol M; Vincent, Renaud; Broad, Gayle; Liu, Ling; Dales, Robert

2017-04-01

The effects of industrial air pollution on human health have not been as thoroughly investigated as those of urban air pollution which originates mostly from automotive transport. To better assess the health impacts of point sources of industrial air pollution, a randomized crossover exposure study was conducted. Sixty one young and healthy volunteers were randomly assigned to spend five consecutive eight-hour days near a steel mill or at a location five kilometres away. After a nine or sixteen-day washout period, volunteers spent another five consecutive days at the second site. Meteorological conditions and air pollutants were monitored at both exposure sites. On each exposure day, the first morning urine was collected along with a second urine sample obtained immediately before leaving the exposure site at the end of the day. Urinary levels of biomarkers of oxidative stress 8-hydroxy-2'-deoxyguanosine (8-OHdG, a biomarker of oxidative DNA damage), malondialdehyde (MDA, a biomarker of lipid peroxidation), 8-isoprostane (8-IsoP, a bioactive metabolite resulting from the peroxidation of arachidonic acid) and Vascular Endothelial Growth Factor (VEGF, involved in response to oxidative stress) were measured. According to mixed-effects linear regression models, intra-individual variations in 8-OHdG urinary levels were significantly associated with exposure site, but surprisingly, lower levels were observed at the steel mill site. Delayed, temporally-defined associations with specific air pollutants were observed for 8-OHdG, 8-IsoP and VEGF. However, these associations were subtle, presented complex patterns and their biological consequences remain unclear. Crown Copyright © 2016. Published by Elsevier GmbH. All rights reserved.

32. EXTERIOR VIEW LOOKING INTO THE SEVENTH TAILRACE (COUNTING FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. EXTERIOR VIEW LOOKING INTO THE SEVENTH TAILRACE (COUNTING FROM THE DOWNSTREAM END TO THE UPSTREAM END - SOUTHEAST TO NORTHWEST). THIS AREA IS THE PORTION OF THE PULP MILL THAT WAS NEVER REBUILT AFTER A DEVASTATING FIRE IN 1925 AND SUBSEQUENT END TO PULP PRODUCTION AT THIS SITE. NOTE THE DRIVE SHAFT AND OTHER REMNANTS FROM THE PULP MILLING OPERATION. - Potomac Power Plant, On West Virginia Shore of Potomac River, about 1 mile upriver from confluence with Shenandoah River, Harpers Ferry, Jefferson County, WV

Probing the magnetic moment of FePt micromagnets prepared by focused ion beam milling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Overweg, H. C.; Haan, A. M. J. den; Eerkens, H. J.

2015-08-17

We investigate the degradation of the magnetic moment of a 300 nm thick FePt film induced by Focused Ion Beam (FIB) milling. A 1 μm × 8 μm rod is milled out of a film by a FIB process and is attached to a cantilever by electron beam induced deposition. Its magnetic moment is determined by frequency-shift cantilever magnetometry. We find that the magnetic moment of the rod is μ = 1.1 ± 0.1 × 10{sup −12} Am{sup 2}, which implies that 70% of the magnetic moment is preserved during the FIB milling process. This result has important implications for atom trapping and magnetic resonance force microscopy, which are addressed inmore » this paper.« less

Magnesium Nanocomposites: Current Status and Prospects for Army Applications

DTIC Science & Technology

2011-09-01

and reinforcement that cannot be produced through melt-based processing . In mechanical alloying , the powder and milling media are placed into...mixing vessels that are agitated in a high-energy milling machine. During the mixing process , the powder particles undergo repeated cycles of cold ...welding and fracturing of interparticle bonds. At the end of the process , the powder has been alloyed to the desired composition. Although typically used

Coliform Bacteria and Nitrogen Fixation in Pulp and Paper Mill Effluent Treatment Systems

PubMed Central

Gauthier, Francis; Neufeld, Josh D.; Driscoll, Brian T.; Archibald, Frederick S.

2000-01-01

The majority of pulp and paper mills now biotreat their combined effluents using activated sludge. On the assumption that their wood-based effluents have negligible fixed N, and that activated-sludge microorganisms will not fix significant N, these mills routinely spend large amounts adding ammonia or urea to their aeration tanks (bioreactors) to permit normal biomass growth. N2 fixation in seven Eastern Canadian pulp and paper mill effluent treatment systems was analyzed using acetylene reduction assays, quantitative nitrogenase (nifH) gene probing, and bacterial isolations. In situ N2 fixation was undetectable in all seven bioreactors but was present in six associated primary clarifiers. One primary clarifier was studied in greater detail. Approximately 50% of all culturable cells in the clarifier contained nifH, of which >90% were Klebsiella strains. All primary-clarifier coliform bacteria growing on MacConkey agar were identified as klebsiellas, and all those probed contained nifH. In contrast, analysis of 48 random coliform isolates from other mill water system locations showed that only 24 (50%) possessed the nifH gene, and only 13 (27%) showed inducible N2-fixing activity. Thus, all the pulp and paper mill primary clarifiers tested appeared to be sites of active N2 fixation (0.87 to 4.90 mg of N liter−1 day−1) and a microbial community strongly biased toward this activity. This may also explain why coliform bacteria, especially klebsiellas, are indigenous in pulp and paper mill water systems. PMID:11097883

The effects of lumber length on part yields in gang-rip-first rough mills

Treesearch

Peter C. Hamner; Brian H. Bond; Janice K. Wiedenbeck

2002-01-01

The lumber processed in most rough mills typically arrives from vendors in packages of random width boards with lengths ranging from 8 to 16 feet. However, little attention has been given to analyzing how differences in board lengths affect rough mill yield given varying part-prioritization strategies and cutting bill scenarios. The objective of this study was to...

Effect of microwave- and microwave-convection drying conditions on the total soluble phenolic content of 2-phase olive mill waste

USDA-ARS?s Scientific Manuscript database

The California olive oil industry produces tons of 2-phase olive mill waste (2POMW) every year as a byproduct of the olive oil milling process. 2POMW is rich in health-promoting phenolic compounds, but it is greater than 60% moisture (wet basis) in its native form and thus expensive to store and tr...

Rough Mill Simulations Reveal That Productivity When Processing Short Lumber Can Be High

Treesearch

Janice K. Wiedenbeck; Philip A. Araman

1995-01-01

Handling rates and costs associated with using short-length lumber (less than 8 ft. long) in furniture and cabinet industry rough mills have been assumed to be prohibitive. Discrete-event systems simulation models of both a crosscut-first and gang-rip-first rough mill were built to measure the effect of lumber length on equipment utilization and the volume and value of...

Shoot water relations of mature black spruce families displaying a genotype x environment interaction in growth rate. I. Family and site effects over three growing seasons

Treesearch

Kurt H. Johnsen; John E Major

1999-01-01

Pressure-volume curves were determined for black spruce (Picea mariana (Mill.) BSP) trees from four full-sib families. During the first two years, trees were measured from a plantation on a dry site. In the third year, trees were sampled from the dry site and a wet site. Diurnal measurements of shoot water potential allowed in situ ...

The effects of the mechanical–chemical stabilization process for municipal solid waste incinerator fly ash on the chemical reactions in cement paste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Cheng-Gang; Sun, Chang-Jung, E-mail: sun.3409@hotmail.com; Gau, Sue-Huai

2013-04-15

Highlights: ► Milling extracted MSWI fly ash. ► Increasing specific surface area, destruction of the crystalline texture, and increasing the amount of amorphous materials. ► Increasing heavy metal stability. ► Inducing pozzolanic reactions and increasing the early and later strength of the cement paste. - Abstract: A water extraction process can remove the soluble salts present in municipal solid waste incinerator (MSWI) fly ash, which will help to increase the stability of the synthetic materials produced from the MSWI fly ash. A milling process can be used to stabilize the heavy metals found in the extracted MSWI fly ash (EA)more » leading to the formation of a non-hazardous material. This milled extracted MSWI fly ash (MEA) was added to an ordinary Portland cement (OPC) paste to induce pozzolanic reactions. The experimental parameters included the milling time (96 h), water to binder ratios (0.38, 0.45, and 0.55), and curing time (1, 3, 7 and 28 days). The analysis procedures included inductively coupled plasma atomic emission spectroscopy (ICP/AES), BET, mercury intrusion porosimetry (MIP), X-ray diffraction (XRD), and nuclear magnetic resonance (NMR) imaging. The results of the analyses indicate that the milling process helped to stabilize the heavy metals in the MEA, with an increase in the specific surface area of about 50 times over that of OPC. The addition of the MEA to the OPC paste decreased the amount of Ca(OH){sub 2} and led to the generation of calcium–silicate–hydrates (C–S–H) which in turned increased the amount of gel pores and middle sized pores in the cement. Furthermore, a comparison shows an increase in the early and later strength over that of OPC paste without the addition of the milled extracted ash. In other words, the milling process could stabilize the heavy metals in the MEA and had an activating effect on the MEA, allowing it to partly substitute OPC in OPC paste.« less

Three-dimensional organization of the endoplasmic reticulum membrane around the mitochondrial constriction site in mammalian cells revealed by using focused-ion beam tomography.

PubMed

Ohta, Keisuke; Okayama, Satoko; Togo, Akinobu; Nakamura, Kei-Ichiro

2014-11-01

The endoplasmic reticulum (ER) and mitochondria associate at multiple contact sites to form specific domains known as mitochondria-ER associated membranes (MAMs) that play a role in the regulation of various cellular processes such as Ca2+ transfer, autophagy, and inflammation. Recently, it has been suggested that MAMs are also involved in mitochondrial dynamics, especially fission events. Cytological analysis showed that ER tubules were frequently located close to each other in mitochondrial fission sites that accumulate fission-related proteins. Three-dimensional (3D) imaging of ER-mitochondrial contacts in yeast mitochondria by using cryo-electron tomography also showed that ER tubules were attached near the constriction site, which is considered to be a fission site1). MAMs have been suggested to play a role in the initiation of mitochondrial fission, although the molecular relationships between MAMs and the mitochondrial fission process have not been established. Although an ER-mitochondrial membrane association has also been observed at the fission site in mammalian mitochondria, the detailed organization of MAMs around mammalian mitochondria remains to be established. To visualize the 3D distribution of the ER-mitochondrial contacts around the mitochondria, especially around the constriction site in mammalian cells, we attempted 3D structural analysis of the mammalian cytoplasm using high-resolution focused ion-beam scanning electron microscopy (FIB-SEM) tomography, and observed the distribution pattern of ER contacts around the mammalian mitochondrial constriction site.Rat hepatocytes and HeLa cells were used. Liver tissue was obtained from male rats (Wistar, 6W) fixed by transcardial perfusion of 2% paraformaldehyde and 2.5% glutaraldehyde in 0.1 M cacodylate buffer (pH 7.4) under deep anesthesia. HeLa cells were fixed with the same fixative. The specimens were then stained en bloc to enhance membrane contrast and embedded in epoxy resin2). The surface of the specimens was freshly exposed using an ultramicrotome and examined by FIB/SEM (Quanta 3D FEG, FEI, USA). Ion-beam milling and image acquisition cycles were performed under the following conditions. The milling was performed with a gallium ion beam at 30 kV with a current of 100 pA, with a milling pitch of 10 nm/step. Material contrast images using backscattered electrons (BSE) were acquired at a landing energy of 2 keV with a bias voltage of 1.5-2.5 kV using a vCD detector. The remaining acquisition parameters were as follows: beam current = 11 pA, dwell time = 6-30 µs/pixel, image size = 1024 × 883 pixel (5.9 × 5.1 µm), pixel size = 5.8 nm/pixel. The resultant image stack was processed using Avizo 6.3 and Amira 5.4(FEI, USA).Reconstructed volume showed the existence of several constriction sites on mitochondria in both chemically fixed normal hepatocytes and HeLa cells. Each material contrast image of specimen surfaces showed two types of membrane associations between the ER and mitochondria. The first was an osmiophilic bridge-like structure; these bridges were approximately 50 nm in length, and they connected the ER membrane and the mitochondrial outer membrane (OMM). The second was a close apposition (< 20 nm) of the ER membrane and the OMM. Membrane segmentation revealed the 3D distribution of the membrane contacts; 10 to 20% of the mitochondrial surface was occupied by ER contacts. No fundamental difference was observed between hepatocytes and HeLa cells in the distribution pattern of the contacts. Although ER-contacts and bridge-like structures were occasionally found to accumulate around the mitochondrial constriction area, we did not observe any ring-like ER tubules around the mammalian mitochondrial constriction site, as in yeast. These results suggest that the role of ER-membrane associations in the mitochondrial fission process may differ between mammals and yeast. © The Author 2014. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Multiphysical FE-analysis of a front-end bending phenomenon in a hot strip mill

NASA Astrophysics Data System (ADS)

Ilmola, Joonas; Seppälä, Oskari; Leinonen, Olli; Pohjonen, Aarne; Larkiola, Jari; Jokisaari, Juha; Putaansuu, Eero

2018-05-01

In hot steel rolling processes, a slab is generally rolled to a transfer bar in a roughing process and to a strip in a hot strip rolling process. Over several rolling passes the front-end may bend upward or downward due to asymmetrical rolling conditions causing entry problems in the next rolling pass. Many different factors may affect the front-end bending phenomenon and are very challenging to measure. Thus, a customized finite element model is designed and built to simulate the front-end bending phenomenon in a hot strip rolling process. To simulate the functioning of the hot strip mill precisely, automated controlling logic of the mill must be considered. In this paper we studied the effect of roll bite friction conditions and amount of reduction on the front-end bending phenomenon in a hot strip rolling process.

An experimental analysis of process parameters to manufacture micro-channels in AISI H13 tempered steel by laser micro-milling

NASA Astrophysics Data System (ADS)

Teixidor, D.; Ferrer, I.; Ciurana, J.

2012-04-01

This paper reports the characterization of laser machining (milling) process to manufacture micro-channels in order to understand the incidence of process parameters on the final features. Selection of process operational parameters is highly critical for successful laser micromachining. A set of designed experiments is carried out in a pulsed Nd:YAG laser system using AISI H13 hardened tool steel as work material. Several micro-channels have been manufactured as micro-mold cavities varying parameters such as scanning speed (SS), pulse intensity (PI) and pulse frequency (PF). Results are obtained by evaluating the dimensions and the surface finish of the micro-channel. The dimensions and shape of the micro-channels produced with laser-micro-milling process exhibit variations. In general the use of low scanning speeds increases the quality of the feature in both surface finishing and dimensional.

Bioluminescence inhibition assays for toxicity screening of wood extractives and biocides in paper mill process waters.

PubMed

Rigol, Anna; Latorre, Anna; Lacorte, Sílvia; Barceló, Damià

2004-02-01

The risk associated with wood extractives, biocides, and other additives in pulp and paper mill effluents was evaluated by performing a characterization of process waters and effluents in terms of toxicity and chemical analysis. The individual toxicity of 10 resin acids, two unsaturated fatty acids, and three biocides was estimated by measuring the bioluminescence inhibition with a ToxAlert 100 system. Median effective concentration values (EC50) of 4.3 to 17.9, 1.2 to 1.5, and 0.022 to 0.50 mg/L were obtained, respectively. Mixtures of these three families of compounds showed antagonistic effects. Chemical analysis of process waters was performed by liquid chromatography- and gas chromatography-mass spectrometry. Biocides such as 2-(thiocyanomethylthio)-benzotiazole (TCMTB) (EC50 = 0.022 mg/L) and 2,2-dibromo-3-nitrilpropionamide (DBNPA) (EC50 = 0.50 mg/L) were the most toxic compounds tested and were detected at concentrations of 16 and 59 microg/L, respectively, in a closed-circuit recycling paper mill. Process waters from kraft pulp mills, printing paper mills, and packing board paper mills showed the highest concentration of resin acids (up to 400 microg/L) and accounted for inhibition percentages up to 100%. Detergent degradation products such as nonylphenol (NP) and octylphenol (OP) and the plasticizer bisphenol A (BPA) were also detected in the waters at levels of 0.6 to 10.6, 0.3 to 1.4, and 0.7 to 187 microg/L, respectively. However, once these waters were biologically treated, the concentration of detected organic compounds diminished and the toxicity decreased in most cases to values of inhibition lower than 20%.

Self-assembled nanoparticle arrays as nanomasks for pattern transfer

NASA Astrophysics Data System (ADS)

Sachan, M.; Bonnoit, C.; Hogg, C.; Evarts, E.; Bain, J. A.; Majetich, S. A.; Park, J.-H.; Zhu, J.-G.

2008-07-01

Argon ion milling was used to transfer the pattern of sparse 12 nm iron oxide nanoparticles into underlying thin films of Pt and magnetic tunnel junction stacks and quantify their etching rates and morphological evolution. Under typical milling conditions, Pt milled at 10 nm min-1, while the isolated particles of iron oxide used for the mask milled at 5 nm min-1. Dilute dispersions of nanoparticles were used to produce the sparse nanomasks, and high resolution scanning electron microscopy (SEM) and atomic force microscopy were used to monitor the evolution of etched structures as a function of milling time. SEM measurements indicate an apparent 20% increase in feature diameter before the features began to diminish under additional milling, suggesting redeposition as a limiting feature in the milling of dense arrays. Simulations of the milling process in nanoparticle arrays that include redeposition are consistent with this observation. These simulations predict that an edge-to-edge spacing of 3 nm in a dense array is feasible, but that redeposition reduces the final structure aspect ratio from that of the masking array by as much as a factor of two.

The study on dynamic properties of monolithic ball end mills with various slenderness

NASA Astrophysics Data System (ADS)

Wojciechowski, Szymon; Tabaszewski, Maciej; Krolczyk, Grzegorz M.; Maruda, Radosław W.

2017-10-01

The reliable determination of modal mass, damping and stiffness coefficient (modal parameters) for the particular machine-toolholder-tool system is essential for the accurate estimation of vibrations, stability and thus the machined surface finish formed during the milling process. Therefore, this paper focuses on the analysis of ball end mill's dynamical properties. The tools investigated during this study are monolithic ball end mills with different slenderness values, made of coated cemented carbide. These kinds of tools are very often applied during the precise milling of curvilinear surfaces. The research program included the impulse test carried out for the investigated tools clamped in the hydraulic toolholder. The obtained modal parameters were further applied in the developed tool's instantaneous deflection model, in order to estimate the tool's working part vibrations during precise milling. The application of the proposed dynamics model involved also the determination of instantaneous cutting forces on the basis of the mechanistic approach. The research revealed that ball end mill's slenderness can be considered as an important milling dynamics and machined surface quality indicator.

Considerations on the quantitative analysis of apparent amorphicity of milled lactose by Raman spectroscopy.

PubMed

Pazesh, Samaneh; Lazorova, Lucia; Berggren, Jonas; Alderborn, Göran; Gråsjö, Johan

2016-09-10

The main purpose of the study was to evaluate various pre-processing and quantification approaches of Raman spectrum to quantify low level of amorphous content in milled lactose powder. To improve the quantification analysis, several spectral pre-processing methods were used to adjust background effects. The effects of spectral noise on the variation of determined amorphous content were also investigated theoretically by propagation of error analysis and were compared to the experimentally obtained values. Additionally, the applicability of calibration method with crystalline or amorphous domains in the estimation of amorphous content in milled lactose powder was discussed. Two straight baseline pre-processing methods gave the best and almost equal performance. By the succeeding quantification methods, PCA performed best, although the classical least square analysis (CLS) gave comparable results, while peak parameter analysis displayed to be inferior. The standard deviations of experimental determined percentage amorphous content were 0.94% and 0.25% for pure crystalline and pure amorphous samples respectively, which was very close to the standard deviation values from propagated spectral noise. The reasonable conformity between the milled samples spectra and synthesized spectra indicated representativeness of physical mixtures with crystalline or amorphous domains in the estimation of apparent amorphous content in milled lactose. Copyright © 2016 The Author(s). Published by Elsevier B.V. All rights reserved.

Amorphization of itraconazole by inorganic pharmaceutical excipients: comparison of excipients and processing methods.

PubMed

Grobelny, Pawel; Kazakevich, Irina; Zhang, Dan; Bogner, Robin

2015-01-01

The aim of this study was to investigate the effects of solid carriers and processing routes on the properties of amorphous solid dispersions of itraconazole. Three solid carriers with a range of surface properties were studied, (1) a mesoporous silicate, magnesium aluminum silicate (Neusilin US2), (2) a nonporous silicate of corresponding composition (Veegum) and (3) a non-silicate, inorganic excipient, calcium phosphate dibasic anhydrous (A-TAB). The drug was incorporated via either solvent-deposition or ball milling. Both the maximum drug deposited by solvent-based method that produced an amorphous composite and the time for complete amorphization by co-milling was determined by X-ray powder diffraction (XRPD). Changes in the drug and excipients were monitored by nitrogen adsorption and wettability of the powder. The ability of the excipients to amorphize the drug and enhance its dissolution was related to the powder characteristics. Neusilin provided the fastest amorphization time in the mill and highest drug loading by solvent-deposition, compared with the other two excipients. Solvent-deposition provided greater dissolution enhancement than milling, due to the reduction in Neusilin porosity during high energy milling.This study confirms that substrates as well as the processing routes have notable influence on the drug deposition, amorphization, physical stability and drug in vitro release.

Emissions of PAHs derived from sugarcane burning and processing in Chiapas and Morelos México.

PubMed

Mugica-Alvarez, Violeta; Santiago-de la Rosa, Naxieli; Figueroa-Lara, Jesús; Flores-Rodríguez, Julio; Torres-Rodríguez, Miguel; Magaña-Reyes, Miguel

2015-09-15

Sugarcane burning is an agricultural practice implemented to ease farm worker duties; nevertheless, as a consequence, tons of particles are emitted to the atmosphere. Additionally, during harvesting the sugar-mills operate the whole day emitting hundreds of tons of pollutants. Therefore, health risks to neighboring population should be a major governmental concern, leading first to identification and quantification of toxic compounds, such as polycyclic aromatic hydrocarbons (PAHs). In order to establish the magnitude of the problem, four sampling campaigns of PM10 and PM2.5 were carried out in this study, during harvesting and no-harvesting seasons in two municipalities of México, with different climatic and social conditions. Concentrations of PM10, PM2.5, and organic compounds were determined daily, followed by extraction, identification and quantification of the 17 EPA-established PAHs from all samples. The results showed that during harvest, the PM10 mass increased lightly in Chiapas, but approximately twice in Morelos, whereas total PAH concentrations increased twice and six times, respectively. The most abundant PAHs, namely: indene [1,2,3cd] pyrene, benzo[b]fluoranthene, benzo[a]pyrene and dibenzo [a,h] anthracene are composed of 5 or more aromatic rings. Of the total PAHs quantified, 44% to 52% corresponded to carcinogenic compounds, consequently, the overall carcinogenic potential increased twice or three times. Principal component analysis with varimax rotation was applied to source apportionment at each site, suggesting three different sources during harvesting: the combustion process in the sugar mill, sugarcane burning and vehicular emissions. The combustion markers for sugar mill are, BAA, BBF, BKF, BAP, IND and BGP, whereas for sugarcane burning were ANT, PHE, FLT and PYR. The results obtained indicate that processing and burning sugarcane are the main sources of the PAH levels measured, proving that the health risks are boosted during harvesting due to increases of PM and PAHs. Copyright © 2015 Elsevier B.V. All rights reserved.

40 CFR 406.55 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling Subcategory § 406... to the provisions of this subpart: There shall be no discharge of process waste water pollutants to...

40 CFR 406.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling... technology economically achievable: there shall be no discharge of process waste water pollutants to...

40 CFR 406.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling... technology economically achievable: there shall be no discharge of process waste water pollutants to...

40 CFR 406.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling... technology economically achievable: there shall be no discharge of process waste water pollutants to...

40 CFR 406.55 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling Subcategory § 406... to the provisions of this subpart: There shall be no discharge of process waste water pollutants to...

40 CFR 406.55 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling Subcategory § 406... to the provisions of this subpart: There shall be no discharge of process waste water pollutants to...

40 CFR 406.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling... technology economically achievable: there shall be no discharge of process waste water pollutants to...

The effects of processing techniques on magnesium-based composite

NASA Astrophysics Data System (ADS)

Rodzi, Siti Nur Hazwani Mohamad; Zuhailawati, Hussain

2016-12-01

The aim of this study is to investigate the effect of processing techniques on the densification, hardness and compressive strength of Mg alloy and Mg-based composite for biomaterial application. The control sample (pure Mg) and Mg-based composite (Mg-Zn/HAp) were fabricated through mechanical alloying process using high energy planetary mill, whilst another Mg-Zn/HAp composite was fabricated through double step processing (the matrix Mg-Zn alloy was fabricated by planetary mill, subsequently HAp was dispersed by roll mill). As-milled powder was then consolidated by cold press into 10 mm diameter pellet under 400 MPa compaction pressure before being sintered at 300 °C for 1 hour under the flow of argon. The densification of the sintered pellets were then determined by Archimedes principle. Mechanical properties of the sintered pellets were characterized by microhardness and compression test. The results show that the density of the pellets was significantly increased by addition of HAp, but the most optimum density was observed when the sample was fabricated through double step processing (1.8046 g/cm3). Slight increment in hardness and ultimate compressive strength were observed for Mg-Zn/HAp composite that was fabricated through double step processing (58.09 HV, 132.19 MPa), as compared to Mg-Zn/HAp produced through single step processing (47.18 HV, 122.49 MPa).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raj K. Rajamani; Sanjeeva Latchireddi; Sravan K. Prathy

The U.S. mining industry operates approximately 80 semi-autogenesis grinding mills (SAG) throughout the United States. Depending on the mill size the SAG mills draws between 2 MW and 17 MW. The product from the SAG mill is further reduced in size using pebble crushers and ball mills. Hence, typical gold or copper ore requires between 2.0 and 7.5 kWh per ton of energy to reduce the particle size. Considering a typical mining operation processes 10,000 to 100,000 tons per day the energy expenditure in grinding is 50 percent of the cost of production of the metal. A research team frommore » the University of Utah is working to make inroads into saving energy in these SAG mills. In 2003, Industries of the Future Program of the Department of Energy tasked the University of Utah team to build a partnership between the University and the mining industry for the specific purpose of reducing energy consumption in SAG mills. A partnership was formed with Cortez Gold Mines, Kennecott Utah Copper Corporation, Process Engineering Resources Inc. and others. In the current project, Cortez Gold Mines played a key role in facilitating the 26-ft SAG mill at Cortez as a test mill for this study. According to plant personnel, there were a number of unscheduled shut downs to repair broken liners and the mill throughput fluctuated depending on ore type. The University team had two softwares, Millsoft and FlowMod to tackle the problem. Millsoft is capable of simulating the motion of charge in the mill. FlowMod calculates the slurry flow through the grate and pulp lifters. Based on this data the two models were fine-tuned to fit the Cortez SAG will. In the summer of 2004 a new design of shell lifters were presented to Cortez and in September 2004 these lifters were installed in the SAG mill. By December 2004 Cortez Mines realized that the SAG mill is drawing approximately 236-kW less power than before while maintaining the same level of production. In the first month there was extreme cycling and operators had to learn more. Now the power consumption is 0.3-1.3 kWh/ton lower than before. The actual SAG mill power draw is 230-370 kW lower. Mill runs 1 rpm lesser in speed on the average. The re-circulation to the cone crusher is reduced by 1-10%, which means more efficient grinding of critical size material is taking place in the mill. All of the savings have resulted in reduction of operating cost be about $0.023-$0.048/ ton.« less

Comparison of particle sizes between 238PuO 2 before aqueous processing, after aqueous processing, and after ball milling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mulford, Roberta Nancy

Particle sizes determined for a single lot of incoming Russian fuel and for a lot of fuel after aqueous processing are compared with particle sizes measured on fuel after ball-milling. The single samples of each type are believed to have particle size distributions typical of oxide from similar lots, as the processing of fuel lots is fairly uniform. Variation between lots is, as yet, uncharacterized. Sampling and particle size measurement methods are discussed elsewhere.

High energy ball milling and supercritical carbon dioxide impregnation as co-processing methods to improve dissolution of tadalafil.

PubMed

Krupa, Anna; Descamps, Marc; Willart, Jean-François; Jachowicz, Renata; Danède, Florence

2016-12-01

Tadalafil (TD) is a crystalline drug of a high melting point (T m =299°C) and limited solubility in water (<5μg/mL). These properties may result in reduced and variable bioavailability after oral administration. Since the melting of TD is followed by its decomposition, the drug processing at high temperatures is limited. The aim of the research is, therefore, to improve the dissolution of TD by its co-processing with the hydrophilic polymer Soluplus® (SL) at temperatures below 40°C. In this study, two methods, i.e. high energy ball-milling and supercritical carbon dioxide impregnation (scCO 2 ) are compared, with the aim to predict their suitability for the vitrification of TD. The influence of the amount of SL and the kind of co-processing method on TD thermal properties is analyzed. The results show that only the high energy ball milling process makes it possible to obtain a completely amorphous form of TD, with the characteristic X-ray 'halo' pattern. The intensity of the Bragg peaks diminishes for all the formulations treated with scCO 2 , but these samples remain crystalline. The MDSC results show that high energy ball milling is capable of forcing the mixing of TD and SL at a molecular level, providing a homogeneous amorphous solid solution. The glass transition temperatures (T g ), determined for the co-milled formulations, range from 79°C to 139°C and they are higher than T g of pure SL (ca. 70°C) and lower than T g of pure TD (ca. 149°C). In contrast to the co-milled formulations which are in the form of powder, all the formulations after scCO 2 impregnation form a hard residue, sticking to the reaction vessel, which needs to be ground before analysis or further processing. Finally, the dissolution studies show that not only has SL a beneficial effect on the amount of TD dissolved, but also both co-processing methods make the dissolution enhancement of TD possible. After co-processing by scCO 2 , the amount of TD dissolved increases with the decreasing amount of SL, whereas in the case of the co-milled formulations, the higher the amount of SL in the glassy solution is, the higher the amount of TD dissolved. Copyright © 2016 Elsevier B.V. All rights reserved.

40 CFR 61.190 - Designation of facilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Lewiston, New York; the Weldon Spring Site, Weldon Spring, Missouri; the Middlesex Sampling Plant, Middlesex, New Jersey; the Monticello Uranium Mill Tailings Pile, Monticello, Utah. This subpart does not...

Powder processing and mechanical properties of Silver0.86Lead19Antimony telluride20 (LAST) and Lead0.95Tin0.05Tellurium - Lead sulfide 8% (Lead telluride -Lead sulfide) thermoelectric materials

NASA Astrophysics Data System (ADS)

Ni, Jennifer Elisabeth

Thermoelectric (TE) materials convert between thermal and electrical energy and when used with existing processes will increase the efficiency via waste heat recovery. Ag0.86Pb19SbTe20 (LAST) and Pb0.95Sn0.05Te - PbS 8% (PbTe-PbS) materials exhibit good thermoelectric (TE) properties and have potential applications as thermoelectric generators in waste heat recovery. However, to fully characterize the thermo-mechanical behavior of LAST and PbTe-PbS materials under in-service conditions, knowledge is needed of the mechanical and thermal properties at room and high temperature. As fracture strength is inversely proportional to the square root of grain size, cast ingots were powder processed to reduce powder particle size. Three different powder processing methods were used (1) dry milling only, (2) wet milling only, or (3) dry milling and wet milling The specimens were fabricated using hot pressing or pulsed electric current sintering (PECS) from planetary ball milled powders. In this study, elastic moduli, including Young's modulus, shear modulus, and Poisson's ratio, were measured dynamically using resonant ultrasound spectroscopy (RUS) at room temperature and as a function of temperature up to 663 K. The room temperature porosity dependence for Young's modulus followed the empirical exponential relationships common for brittle materials, with a material dependent constant bPE of 3.5 and 1.3 for LAST and PbTe-PbS, respectively. The room temperature Young's modulus for a theoretically dense specimen was 58.4 +/- 0.6 GPa and 56.2 +/- 0.4 GPa for for LAST and PbTe-PbS, respectively. For hot pressed PbTe-PbS specimens, the Vickers indentations mean hardness and fracture toughness was 1.18 + 0.09 GPa and 0.35 +/- 0.04 MPa·m 1/2. The coefficient of thermal expansion is important for understanding the mechanical response of a material to a thermal gradient or a thermal transient. For PbTe-PbS the coefficient of thermal expansion measured using dilatometry and high temperature x-ray diffraction was 21.5 x 10-6 K -1. Bloating during post-densification annealing was measured indirectly using resonant ultrasound spectroscopy and dilatometry and directly using scanning electron microscopy. Dry milled only PECS-processed PbTe-PbS specimens did not bloat during post-densification anneals up to 936 K. Hot pressed and PECS-processed specimens processed from wet milled and dry and wet milled powder bloated during densification anneals at temperatures over 603 K.

Towards quality by design in pharmaceutical manufacturing: modelling and control of air jet mills

NASA Astrophysics Data System (ADS)

Bhonsale, Satyajeet; Telen, Dries; Stokbroekx, Bard; Van Impe, Jan

2017-06-01

Milling is an important step in pharmaceutical manufacturing as it not only determines the final formulation of the drug product, but also influences the bioavailability and dissolution rate of the active pharmaceutical ingredient (API). In this respect, the air jet mill (AJM) is most commonly used in the pharmaceutical industry as it is a non-contaminating and non-degrading self-classifying process capable of delivering narrow particle size distributions (PSD). Keeping the principles of Quality by Design in mind, the Critical Process Parameters (CPPs) of the AJM have been identified to be the pressures at the grinding nozzles, and the feed rate which affect the PSD, surface charge and the morphology of the product (i.e. the Critical Material Attributes (CMAs)). For the purpose of this research, the PSD is considered to be the only relevant CMA. A population balance based model is proposed to simulate the dynamics milling operation by utilizing the concept of breakage functions. This model agrees qualitatively with experimental observations of the air jet mill unit present at Janssen Pharmaceutica but further steps for model validation need to be carried out.

Ball milling pretreatment of oil palm biomass for enhancing enzymatic hydrolysis.

PubMed

Zakaria, Mohd Rafein; Fujimoto, Shinji; Hirata, Satoshi; Hassan, Mohd Ali

2014-08-01

Oil palm biomass, namely empty fruit bunch and frond fiber, were pretreated using a planetary ball mill. Particle sizes and crystallinity index values of the oil palm biomass were significantly reduced with extended ball mill processing time. The treatment efficiency was evaluated by the generation of glucose, xylose, and total sugar conversion yields from the pretreatment process compared to the amount of sugars from raw materials. Glucose and xylose contents were determined using high-performance liquid chromatography. An increasing trend in glucose and xylose yield as well as total sugar conversion yield was observed with decreasing particle size and crystallinity index. Oil palm frond fiber exhibited the best material yields using ball milling pretreatment with generated glucose, xylose, and total sugar conversion yields of 87.0, 81.6, and 85.4%, respectively. In contrast, oil palm empty fruit bunch afforded glucose and xylose of 70.0 and 82.3%, respectively. The results obtained in this study showed that ball mill-treated oil palm biomass is a suitable pretreatment method for high conversion of glucose and xylose.

Powder metallurgy of Ge, Si, and Ge-Si

NASA Astrophysics Data System (ADS)

Schilz, Jürgen; Langenbach, Marion

1993-03-01

id="ab1"Planetary ball-milling and pressing behaviour of Ge, Si and Ge-Si powder mixtures are investigated. Scanning and transmission electron microscopy observations revealed the different microstructure of the two elements after milling: Ge remains in a microcrystalline state, whereas Si can be comminuted into grains consisting of nanocrystalline regions. Planetary milling of the two elements together, using agate balls and vial, did not reveal any compound formation. By hot-isostatic pressing, pure Ge and Ge-Si mixtures were densified to a higher value than pure Si. This denotes a plastic flow of the Ge component at a process temperature of 800°C. The microhardness of hot-pressed Ge reaches the bulk value; hot-pressed Si is very soft. Energy dispersive X-ray analysis and X-ray diffraction did not detect any impurity contamination from vial and milling media wear. Moreover, by electrical transport measurements it turned out that the net carrier concentration density resulting from electrical active impurities introduced by the milling and pressing process is below 2 x 1016 cm 3 at room temperature.

Mechanism of solid state amorphization of glucose upon milling.

PubMed

Dujardin, N; Willart, J F; Dudognon, E; Danède, F; Descamps, M

2013-02-07

Crystalline α-glucose is known to amorphize upon milling at -15 °C while it remains structurally invariant upon milling at room temperature. We have taken advantage of this behavior to compare the microstructural evolutions of the material in both conditions in order to identify the essential microstructural features which drive the amorphization process upon milling. The investigations have been performed by differential scanning calorimetry and by powder X-ray diffraction. The results indicate that two different amorphization mechanisms occur upon milling: an amorphization at the surface of crystallites due to the mechanical shocks and a spontaneous amorphization of the crystallites as they reach a critical size, which is close to 200 Å in the particular case of α-glucose.

Ground water hydrology report: Revision 1, Attachment 3. Final

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-01

This report presents ground water hydrogeologic activities for the Maybell, Colorado, Uranium Mill Tailings Remedial Action Project site. The Department of Energy has characterized the hydrogeology, water quality, and water resources at the site and determined that the proposed remedial action would comply with the requirements of the EPA ground water protection standards.

Environmental Assessment of Ground Water Compliance at the Durango, Colorado, UMTRA Project Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

N /A

2002-11-29

The U.S. Department of Energy (DOE) is proposing a ground water compliance strategy for the Uranium Mill Tailings Remedial Action (UMTRA) Project site near Durango, Colorado. DOE has prepared this environmental assessment to provide the public with information concerning the potential effects of this proposed strategy.

Mulch and Hexazinone Herbicide Shorten the Time Longleaf Pine Seedlings are in the Grass Stage and Increase Height Growth

Treesearch

James D. Haywood

2000-01-01

Herbaceous plant control with mulch or hexazinone herbicide influenced planted longleaf pine (Pinus palustris Mill.) seedling total height on a silt loam site in central Louisiana. The site had been sheared and windrowed in 1991, and rotary mowed before three treatments were...

Space processing applications of ion beam technology. [surface finishing, welding, milling and film deposition

NASA Technical Reports Server (NTRS)

Grodzka, P. G.

1977-01-01

Ion thruster engines for spacecraft propulsion can serve as ion beam sources for potential space processing applications. The advantages of space vacuum environments and the possible gravity effects on thruster ion beam materials operations such as thin film growth, ion milling, and surface texturing were investigated. The direct gravity effect on sputter deposition and vapor deposition processes are discussed as well as techniques for cold and warm welding.

Influence of forest and rangeland management on anadromous fish habitat in Western North America: processing mills and camps.

Treesearch

Donald C. Schmiege

1980-01-01

For nearly 50 years, effluents from pulp and paper mills have been known to be toxic to fish and other aquatic animals. Lethal concentrations have been determined for several species of fish and other organisms. Many factors- -such as water temperature, age of fish, and additional stresses—affect the ability of fish to withstand pollution. Kraft mill wastes...

IMPROVED MAGNESIUM OXIDE SLIP CASTING METHOD

DOEpatents

Stoddard, S.D.; Nuckolls, D.E.

1963-12-31

A process for making an aqueous magnesium oxide slip casting slurry comprising the steps of mixing finely ground fused magnesium oxide with water, milling the slurry for at least 30 hours at a temperature of 2-10 deg C (the low temperature during milling inhibiting the formation of hydrated magnesium oxide), discharging the slurry from the mill, adding hydrochloric acid as a deflocculent, and adding a scum inhibitor is presented. (AEC)

Engineering assessment of inactive uranium mill tailings, Gunnison Site, Gunnison, Colorado. Phase II, Title I

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1977-11-01

Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Gunnison, Colorado. The Phase II - Title I services include the preparation of topographic measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 0.5 million tons of tailings at the Gunnison site constitutes the most significant environmental impact, although windblownmore » tailings and external gamma radiation are also factors. The nine alternative actions presented range from millsite decontamination (Option I), to adding various depths of stabilization cover material (Options II and III), to removal of the tailings to long-term storage sites and decontamination of the present site (Options IV through IX). Cost estimates for the nine options range from $480,000 to $5,890,000. Reprocessing the tailings for uranium does not appear to be economically attractive at present.« less

Fractionation of the rice bran layer and quantification of vitamin E, oryzanol, protein, and rice bran saccharide

PubMed Central

Schramm, Rebecca; Abadie, Alicia; Hua, Na; Xu, Zhimin; Lima, Marybeth

2007-01-01

Value-added processing with respect to rice milling has traditionally treated the rice bran layer as a homogenous material that contains significant concentrations of high-value components of interest for pharmaceutical and nutraceutical applications. Investigators have shown that high-value components in the rice bran layer vary from differences in kernel-thickness, bran fraction, rice variety, and environmental conditions during the growing season. The objectives of this study were to quantify the amount of rice bran removed at pre-selected milling times and to correlate the amount of rice bran removed at each milling time with the concentration of vitamin E, gamma-oryzanol, rice bran saccharide, and protein obtained. The ultimate goal of this research is to show that rice bran fractionation is a useful method to obtain targeted, nutrient-rich bran samples for value-added processing. Two long grain rice cultivars, Cheniere and Cypress, were milled at discrete times between 3 and 40 seconds using a McGill mill to obtain bran samples for analysis. Results showed that the highest oryzanol and protein concentrations were found in the outer portion of the rice bran layer, while the highest rice bran saccharide concentration was found in the inner portion of the bran layer. Vitamin E concentration showed no significant difference across the bran layer within a variety, though the highest magnitude of concentration occurs within the first 10 seconds of milling for both varieties. To extract the higher concentration of oryzanol and protein only the outer portion of the bran layer requires processing, while to extract the higher concentration of rice bran saccharide, only the inner portion of the bran layer requires processing. Rice bran fractionation allows for the selective use of portions of the bran layer and is advantageous for two reasons: (1) bran fractions contain higher concentrations of components of interest with respect to the overall bran layer average, and (2) less bran needs to be processed to obtain components of interest. PMID:18271946

Impact of process parameters on the breakage kinetics of poorly water-soluble drugs during wet stirred media milling: a microhydrodynamic view.

PubMed

Afolabi, Afolawemi; Akinlabi, Olakemi; Bilgili, Ecevit

2014-01-23

Wet stirred media milling has proven to be a robust process for producing nanoparticle suspensions of poorly water-soluble drugs. As the process is expensive and energy-intensive, it is important to study the breakage kinetics, which determines the cycle time and production rate for a desired fineness. Although the impact of process parameters on the properties of final product suspensions has been investigated, scant information is available regarding their impact on the breakage kinetics. Here, we elucidate the impact of stirrer speed, bead concentration, and drug loading on the breakage kinetics via a microhydrodynamic model for the bead-bead collisions. Suspensions of griseofulvin, a model poorly water-soluble drug, were prepared in the presence of two stabilizers: hydroxypropyl cellulose and sodium dodecyl sulfate. Laser diffraction, scanning electron microscopy, and rheometry were used to characterize them. Various microhydrodynamic parameters including a newly defined milling intensity factor was calculated. An increase in either the stirrer speed or the bead concentration led to an increase in the specific energy and the milling intensity factor, consequently faster breakage. On the other hand, an increase in the drug loading led to a decrease in these parameters and consequently slower breakage. While all microhydrodynamic parameters provided significant physical insight, only the milling intensity factor was capable of explaining the influence of all parameters directly through its strong correlation with the process time constant. Besides guiding process optimization, the analysis rationalizes the preparation of a single high drug-loaded batch (20% or higher) instead of multiple dilute batches. Copyright © 2013 Elsevier B.V. All rights reserved.

Magnetic properties of ball-milled SrFe12O19 particles consolidated by Spark-Plasma Sintering

PubMed Central

Stingaciu, Marian; Topole, Martin; McGuiness, Paul; Christensen, Mogens

2015-01-01

The room-temperature magnetic properties of ball-milled strontium hexaferrite particles consolidated by spark-plasma sintering are strongly influenced by the milling time. Scanning electron microscopy revealed the ball-milled SrFe12O19 particles to have sizes varying over several hundred nanometers. X-Ray powder-diffraction studies performed on the ball-milled particles before sintering clearly demonstrate the occurrence of a pronounced amorphization process. During sintering at 950 oC, re-crystallization takes place, even for short sintering times of only 2 minutes and transformation of the amorphous phase into a secondary phase is unavoidable. The concentration of this secondary phase increases with increasing ball-milling time. The remanence and maximum magnetization values at 1T are weakly influenced, while the coercivity drops dramatically from 2340 Oe to 1100 Oe for the consolidated sample containing the largest amount of secondary phase. PMID:26369360

San Sebastián: the social and political effects of sugar mill closure in Mexico.

PubMed

Powell, Kathy

2007-01-01

Mexico's sugar mills face an uncertain future: the closure of San Sebastián may well presage others if the climate for sugar production on national and international levels does not improve. While the continued squeezing of small cane producers reflects processes affecting peasant agriculture generally in Mexico, and indeed beyond, the fate of the mill workers made redundant when the mill closed similarly mirrors broad tendencies in labor in both the developed and developing world under neoliberalism. Former workers fell back upon personal, family, and community resources by migrating to the U.S. or locally reconstructing livelihoods characterized by a reduction in income, security, and access to social benefits. This article reports on the impact of the mill closure on the livelihoods of former mill worker families in the community of San Sebastián and offers some observations on their responses to the situation.

Effect of temperature, time, and milling process on yield, flavonoid, and total phenolic content of Zingiber officinale water extract

NASA Astrophysics Data System (ADS)

Andriyani, R.; Kosasih, W.; Ningrum, D. R.; Pudjiraharti, S.

2017-03-01

Several parameters such as temperature, time of extraction, and size of simplicia play significant role in medicinal herb extraction. This study aimed to investigate the effect of those parameters on yield extract, flavonoid, and total phenolic content in water extract of Zingiber officinale. The temperatures used were 50, 70 and 90°C and the extraction times were 30, 60 and 90 min. Z. officinale in the form of powder and chips were used to study the effect of milling treatment. The correlation among those variables was analysed using ANOVA two-way factors without replication. The result showed that time and temperature did not influence the yield of extract of Powder simplicia. However, time of extraction influenced the extract of simplicia treated without milling process. On the other hand, flavonoid and total phenolic content were not influenced by temperature, time, and milling treatment.

Hydroamination reactions of alkynes with ortho-substituted anilines in ball mills: synthesis of benzannulated N-heterocycles by a cascade reaction.

PubMed

Weiße, Maik; Zille, Markus; Jacob, Katharina; Schmidt, Robert; Stolle, Achim

2015-04-20

It was demonstrated that ortho-substituted anilines are prone to undergo hydroamination reactions with diethyl acetylenedicarboxylate in a planetary ball mill. A sequential coupling of the intermolecular hydroamination reaction with intramolecular ring closure was utilized for the syntheses of benzooxazines, quinoxalines, and benzothiazines from readily available building blocks, that is, electrophilic alkynes and anilines with OH, NH, or SH groups in the ortho position. For the heterocycle formation, it was shown that several stress conditions were able to initiate the reaction in the solid state. Processing in a ball mill seemed to be advantageous over comminution with mortar and pestle with respect to process control. In the latter case, significant postreaction modification occurred during solid-state analysis. Cryogenic milling proved to have an adverse effect on the molecular transformation of the reagents. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Multi-category micro-milling tool wear monitoring with continuous hidden Markov models

NASA Astrophysics Data System (ADS)

Zhu, Kunpeng; Wong, Yoke San; Hong, Geok Soon

2009-02-01

In-process monitoring of tool conditions is important in micro-machining due to the high precision requirement and high tool wear rate. Tool condition monitoring in micro-machining poses new challenges compared to conventional machining. In this paper, a multi-category classification approach is proposed for tool flank wear state identification in micro-milling. Continuous Hidden Markov models (HMMs) are adapted for modeling of the tool wear process in micro-milling, and estimation of the tool wear state given the cutting force features. For a noise-robust approach, the HMM outputs are connected via a medium filter to minimize the tool state before entry into the next state due to high noise level. A detailed study on the selection of HMM structures for tool condition monitoring (TCM) is presented. Case studies on the tool state estimation in the micro-milling of pure copper and steel demonstrate the effectiveness and potential of these methods.

Bioassays with caged hyalella azteca to determine in situ toxicity downstream of two Saskatchewan, Canada, uranium operations.

PubMed

Robertson, Erin L; Liber, Karsten

2007-11-01

The main objectives of this in situ study were to evaluate the usefulness of an in situ bioassay to determine if downstream water bodies at the Key Lake and Rabbit Lake uranium operations (Saskatchewan, Canada) were toxic to Hyalella azteca and, if toxicity was observed, to differentiate between the contribution of surface water and sediment contamination to in situ toxicity. These objectives were achieved by performing 4-d in situ bioassays with laboratory-reared H. azteca confined in specially designed, paired, surface water and sediment exposure chambers. Results from the in situ bioassays revealed significant mortality, relative to the respective reference site, at the exposure sites at both Key Lake (p

Natural and Enhanced Attenuation of Soil and Groundwater at the Monument Valley, Arizona, DOE Legacy Waste Site—10281

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waugh, W.J.; Miller, D.E.; Morris, S.A.

2010-03-07

The U.S. Department of Energy (DOE), the Navajo Nation, and the University of Arizona are exploring natural and enhanced attenuation remedies for groundwater contamination at a former uranium-ore processing site near Monument Valley, Arizona. DOE removed radioactive tailings from the Monument Valley site in 1994. Nitrate and ammonium, waste products of the milling process, remain in an alluvial groundwater plume spreading from the soil source where tailings were removed. Planting and irrigating two native shrubs, fourwing saltbush and black greasewood, markedly reduced both nitrate and ammonium in the source area over an 8-year period. Total nitrogen dropped from 350 mg/kgmore » in 2000 to less than 200 mg/kg in 2008. Most of the reduction is attributable to irrigation-enhanced microbial denitrification rather than plant uptake. However, soil moisture and percolation flux monitoring show that the plantings control the soil water balance in the source area, preventing additional leaching of nitrogen compounds. Enhanced denitrification and phytoremediation also look promising for plume remediation. Microcosm experiments, nitrogen isotopic fractionation analysis, and solute transport modeling results suggest that (1) up to 70 percent of nitrate in the plume has been lost through natural denitrification since the mill was closed in 1968, and (2) injection of ethanol may accelerate microbial denitrification in plume hot spots. A field-scale ethanol injection pilot study is underway. Landscape-scale remote sensing methods developed for the project suggest that transpiration from restored native phreatophyte populations rooted in the aquifer could limit further expansion of the plume. An evaluation of landfarm phytoremediation, the irrigation of native shrub plantings with high nitrate water pumped from the alluvial aquifer, is also underway.« less

Using thermally stimulated current (TSC) to investigate disorder in micronized drug substance produced at different milling energies.

PubMed

Forcino, Rachel; Brum, Jeffrey; Galop, Marc; Sun, Yan

2010-10-01

To investigate the use of thermally stimulated current (TSC) to characterize disorder resulting from micronization of a crystalline drug substance. Samples processed at different milling energies are characterized, and annealing studied. Molecular mobility in micronized drug substance was studied using TSC and compared to results from differential scanning calorimetry (DSC). The micronized drug substance TSC spectra are compared to crystalline and amorphous references. TSC shows distinct relaxation modes for micronized material in comparison to a single weak exotherm observed with DSC. Molecular mobility modes are unique for micronized material compared to the amorphous reference indicating physically distinct disorder compared to phase-separated amorphous material. Signals are ascribed as arising from crystal defects. TSC differentiates material processed at different milling energies showing reasonable correlation between the AUC of the α-relaxation and micronization energy. The annealing process of crystal defects in micronized drug appears to proceed differently for α and β relaxations. TSC proves sensitive to the crystal defects in the micronized drug substance studied here. The technique is able to differentiate distinct types of disorder and can be used to characterize noncrystalline regions arising from milling processes which are physically distinct from amorphous material.

Hardwood regeneration related to overstory shortleaf pine (Pinus echinata mill.) basal area, site index, and time since cutting in Arkansas and eastern Oklahoma

Treesearch

Douglas J. Stevenson; Thomas B. Lynch; James M. Guldin

2010-01-01

Shortleaf pine grows in association with many other species, particularly understory hardwoods, which compete with it, limiting its productivity (Bower and Ferguson 1968, Cain 1988). Which species are the most competitive varies with site quality, density of the pine overstory and years since thinning. Basal area and site index closely approximate the principle...

AmeriFlux CA-Gro Ontario - Groundhog River, Boreal Mixedwood Forest.

DOE Data Explorer

McCaughey, Harry [Queen's University

2016-01-01

This is the AmeriFlux version of the carbon flux data for the site CA-Gro Ontario - Groundhog River, Boreal Mixedwood Forest.. Site Description - Groundhog River (FCRN or CCP site "ON-OMW") is situated in a typical boreal mixedwood forest in northeastern Ontario (48.217 degrees north and 82.156 degrees west) about 80 km southwest of Timmins in Reeves Twp. near the Groundhog River. Rowe (1972) places the site in the Missinaibi-Cabonga Section of the Boreal Forest Region. In terms of ecoregion and ecozone, the site is in the Lake Timiskaming Lowlands of the Boreal Shield. The forest developed after high-grade logging in the 1930's. The average age in 2013 is estimated at beteen 75 and 80 years. The forest is dominated by five species characteristic of Ontario boreal mixedwoods: trembling aspen (Populus tremuloides Michx.), black spruce (Picea mariana (Mill.) B.S.P.), white spruce (Picea glauca (Moench.) Voss.), white birch (Betula papyrifera Marsh.), and balsam fir (Abies balsamea (L.) Mill.). The surficial geology is a lacustrine deposit of varved or massive clays, silts and silty sands. The soil is an orthic gleysol with a soil moisture regime classified as fresh to very fresh. Plonski (1974) rates it as a site class 1. The topography is simple and flat with an overall elevation of 340 m ASL.

2015 Uranium Mill Tailings Radiation Control Act (UMTRCA) Title ll Annual Report, L-Bar, New Mexico Disposal Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frazier, William; Johnson, Dick

The L-Bar, New Mexico, Uranium Mill Tailings Radiation Control Act (UMTRCA) Title II Disposal Site was inspected on August 18, 2015. The tailings impoundment was in excellent condition. Erosion and vegetation measurements to monitor the condition of the impoundment cover indicated that no erosion is occurring, and perennial vegetation foliar cover at the measurement plots increased substantially compared to previous years due to above-average precipitation for the year. A short segment of the perimeter fence near the site entrance was realigned in spring 2015 because a gully was undermining the fence corner. Loose fence strands at another location were repairedmore » during the inspection, and a section of fence needs to be realigned to avoid areas affected by deep gullies and sediment deposition. Inspectors identified no other maintenance needs or cause for a follow-up inspection. Groundwater monitoring is required every 3 years. The next monitoring event will be in 2016.« less

Optimize Operating Conditions on Fine Particle Grinding Process with Vertically Stirred Media Mill

NASA Astrophysics Data System (ADS)

Yang, Yang; Rowson, Neil; Ingram, Andy

2016-11-01

Stirred media mill recently is commonly utilized among mining process due to its high stressing intensity and efficiency. However, the relationship between size reduction and flow pattern within the mixing pot is still not fully understand. Thus, this work investigates fine particle grinding process within vertically stirred media mills by altering stirrer geometry, tip speed and solids loading. Positron Emitting Particle Tracking (PEPT) technology is utilized to plot routine of particles velocity map. By tacking trajectory of a single particle movement within the mixing vessel, the overall flow pattern is possible to be plotted. Ground calcium carbonate, a main product of Imerys, is chosen as feeding material (feed size D80 30um) mixed with water to form high viscous suspension. To obtain fine size product (normally D80 approximately 2um), large amount of energy is drawn by grinding mill to break particles through impact, shear attrition or compression or a combination of them. The results indicate higher energy efficient is obtained with more dilute suspension. The optimized stirrer proves more energy-saving performance by altering the slurry circulate. Imerys Minerals Limited.

Challenges in Special Steel Making

NASA Astrophysics Data System (ADS)

Balachandran, G.

2018-02-01

Special bar quality [SBQ] is a long steel product where an assured quality is delivered by the steel mill to its customer. The bars have enhanced tolerance to higher stress application and it is demanded for specialised component making. The SBQ bars are sought for component making processing units such as closed die hot forging, hot extrusion, cold forging, machining, heat treatment, welding operations. The final component quality of the secondary processing units depends on the quality maintained at the steel maker end along with quality maintained at the fabricator end. Thus, quality control is ensured at every unit process stages. The various market segments catered to by SBQ steel segment is ever growing and is reviewed. Steel mills need adequate infrastructure and technological capability to make these higher quality steels. Some of the critical stages of processing SBQ and the critical quality maintenance parameters at the steel mill in the manufacture has been brought out.

Computer Vision Hardware System for Automating Rough Mills of Furniture Plants

Treesearch

Richard W. Conners; Chong T. Ng; Thomas H. Drayer; Joe G. Tront; D. Earl Kline; C.J. Gatchell

1990-01-01

The rough mill of a hardwood furniture or fixture plant is the place where dried lumber is cut into the rough parts that will be used in the rest of the manufacturing process. Approximately a third of the cost of operating the rough mill is the cost of the raw material. Hence any increase in the number of rough parts produced from a given volume of raw material can...

Effects of Processing and Powder Size on Microstructure and Reactivity in Arrested Reactive Milled Al + Ni

DTIC Science & Technology

2012-05-01

reactive milled (RM) experiments forming nickel aluminides [3,4,6,8–10,12,15,16,18,19], titanium - based alloys [5] and combustion reactions in metal...highly heterogeneous and is refined during processing until reaction occurs. The refinement process consists of the cold welding of powder grains within... welding at the surface of deforming particles, which pro-Table 2 Sample preparation measurements corresponding to the designed exper- iments presented

Mid-Infrared Study of Samples from Several Stones from the Sutter's Mill Meteorite

NASA Technical Reports Server (NTRS)

Sandford, Scott; Nuevo, Michel; Flynn, George J.; Wirick, Sue

2013-01-01

On April 22, 2012, a fireball was observed over California and Nevada, and the falling fragments of the meteorite were detected by weather radar near small townships in the El Dorado County, California. Some of these stones were collected at Sutter s Mill, in the historic site where the California gold rush was initiated, giving the name to this meteorite. Thus far, 77 pieces of the meteorite have been collected, for a total mass of 943 g, with the biggest stone weighing 205 g [1].

43 CFR 3832.34 - How may I use my mill site?

Code of Federal Regulations, 2014 CFR

2014-10-01

... recovery); (2) Mine administrative and support buildings, warehouses and maintenance buildings, electrical... treatment plants; and (6) Any other use that is reasonably incident to mine development and operation...

Identification of the Criteria for Decision Making of Cut-Away Peatland Reuse

NASA Astrophysics Data System (ADS)

Padur, Kadi; Ilomets, Mati; Põder, Tõnis

2017-03-01

The total area of abandoned milled peatlands which need to be rehabilitated for sustainable land-use is nearly 10,000 ha in Estonia. According to the agreement between Estonia and the European Union, Estonia has to create suitable conditions for restoration of 2000 ha of abandoned cut-away peatlands by 2023. The decisions on rehabilitation of abandoned milled peatlands have so far relied on a limited knowledgebase with unestablished methodologies, thus the decision making process needs a significant improvement. This study aims to improve the methodology by identifying the criteria for optimal decision making to ensure sustainable land use planning after peat extraction. Therefore relevant environmental, social and economic restrictive and weighted comparison criteria, which assess reuse alternatives suitability for achieving the goal, is developed in cooperation with stakeholders. Restrictive criteria are arranged into a decision tree to help to determine the implementable reuse alternatives in various situations. Weighted comparison criteria are developed in cooperation with stakeholders to rank the reuse alternatives. The comparison criteria are organised hierarchically into a value tree. In the situation, where the selection of a suitable rehabilitation alternative for a specific milled peatland is going to be made, the weighted comparison criteria values need to be identified and the presented approach supports the optimal and transparent decision making. In addition to Estonian context the general results of the study could also be applied to a cut-away peatlands in other regions with need-based site-dependent modifications of criteria values and weights.

Identification of the Criteria for Decision Making of Cut-Away Peatland Reuse.

PubMed

Padur, Kadi; Ilomets, Mati; Põder, Tõnis

2017-03-01

The total area of abandoned milled peatlands which need to be rehabilitated for sustainable land-use is nearly 10,000 ha in Estonia. According to the agreement between Estonia and the European Union, Estonia has to create suitable conditions for restoration of 2000 ha of abandoned cut-away peatlands by 2023. The decisions on rehabilitation of abandoned milled peatlands have so far relied on a limited knowledgebase with unestablished methodologies, thus the decision making process needs a significant improvement. This study aims to improve the methodology by identifying the criteria for optimal decision making to ensure sustainable land use planning after peat extraction. Therefore relevant environmental, social and economic restrictive and weighted comparison criteria, which assess reuse alternatives suitability for achieving the goal, is developed in cooperation with stakeholders. Restrictive criteria are arranged into a decision tree to help to determine the implementable reuse alternatives in various situations. Weighted comparison criteria are developed in cooperation with stakeholders to rank the reuse alternatives. The comparison criteria are organised hierarchically into a value tree. In the situation, where the selection of a suitable rehabilitation alternative for a specific milled peatland is going to be made, the weighted comparison criteria values need to be identified and the presented approach supports the optimal and transparent decision making. In addition to Estonian context the general results of the study could also be applied to a cut-away peatlands in other regions with need-based site-dependent modifications of criteria values and weights.

Processing mill scale study data on a type 650 electronic machine.

Treesearch

Floyd A. Johnson

1956-01-01

During April 1956, about 20,000 boards from 210 white fir and 290 western hemlock logs were measured at a lumber mill in western Washington. A magnetic drum, data-processing machine (type 650) was then used to calculate board-feet volumes by lumber grade for each log, and average board-foot volumes by lumber grade for each log diameter-class within log grades and...

Mineral scale management Part III, Nonprocess elements in the paper industry

Treesearch

Alan W. Rudie; Peter W. Hart

2006-01-01

Efforts to comply with effluent standards have led to a situation where mills have little leeway in managing trace metals without developing mineral scale deposits. In most cases, the trace metals can be managed with minor process changes and siitable levels of process control. The principal tools available to the mill are pH and good washing in the first chorine...

Using manufacturing simulators to evaluate important processing decisions in the furniture and cabinet industries

Treesearch

Janice K. Wiedenbeck; Philip A. Araman

1995-01-01

We've been telling the wood industry about our process simulation modeling research and development work for several years. We've demonstrated our crosscut-first and rip-first rough mill simulation and animation models. Weâve advised companies on how they could use simulation modeling to help make critically important, pending decisions related to mill layout...

75 FR 65509 - Notice of Lodging of Consent Decree Under the Comprehensive Environmental Response, Compensation...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-25

... is hereby given that on October 14, 2010 a proposed Consent Decree with Georgia-Pacific Consumer... Green Bay Superfund Site in northeastern Wisconsin (the ``Site''). The proposed Consent Decree would... from a line across the River slightly upstream of the company's paper mill in the City of Green Bay...

Longleaf pine site response to repeated fertilization and forest floor removal by raking and prescribed burning

Treesearch

Kim Ludovici; Robert Eaton; Stanley Zarnoch

2018-01-01

Removal of forest floor litter by pine needle raking and prescribed burning is a common practice in longleaf pine (Pinus palustris Mill.) stands on Coastal Plain sites in the Southeastern United States. Repeated removal of litter by raking and the loss of surface organic matter from controlled burns can affect the...

Effects of prescribed fire on vegetation and fuel loads in longleaf pine stands in the bluestem range

Treesearch

James D. Haywood

2010-01-01

Three longleaf pine (Pinus palustris Mill.) sites in the bluestem (Andropogon spp. and Schizachyrium spp.) range were selected in Louisiana for a 40-month study: a shelterwood, a small pole stand, and a newly planted clearcut. On each site, two treatments were applied: check and prescribed fires (PF). Prescribed...

From loblolly to longleaf: fifth-year results of a longleaf pine restoration study at two ecologically distinct sites

Treesearch

Benjamin O. Knapp; G. Geoff Wang; Joan L. Walker; Huifeng Hu

2015-01-01

Historical land-use and management practices in the southeastern United States have resulted in the widespread conversion of many upland sites from dominance of longleaf pine (Pinus palustris Mill.) to loblolly pine (P. taeda L.) in the time following European settlement. Given the ecological, economic, and cultural...

76 FR 72920 - Notification of a Public Teleconference of the Chartered Science Advisory Board

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-28

... Document ``Considerations Related to Post-Closure Monitoring of Uranium In-Situ ISL/ISR Sites.'' DATES: The... Monitoring of Uranium In-Situ ISL/ISR Sites.'' The SAB will comply with the provisions of FACA and all... Environmental Protection Standards for Uranium and Thorium Mill Tailings in regard to underground In-Situ Leach...

Dual centrifugation - A new technique for nanomilling of poorly soluble drugs and formulation screening by an DoE-approach.

PubMed

Hagedorn, Martin; Bögershausen, Ansgar; Rischer, Matthias; Schubert, Rolf; Massing, Ulrich

2017-09-15

The development of nanosuspensions of poorly soluble APIs takes a lot of time and high amount of active material is needed. In this publication the use of dual centrifugation (DC) for an effective and rapid API-nanomilling is described for the first time. DC differs from normal centrifugation by an additional rotation of the samples during centrifugation, resulting in a very fast and powerful movement of the samples inside the vials, which - in combination with milling beads - result in effective milling. DC-nanomilling was compared to conventional wet ball milling and results in same or even smaller particle sizes. Also drug concentrations up to 40% can be processed. The process is fast (typical 90min) and the temperature can be controlled. DC-nanomilling appears to be very gentle, experiments showed no change of the crystal structure during milling. Since batch sizes are very small (100-1000mg) and since 40 sample vials can be processed in parallel, DC is ideal for the screening of suitable polymer/surfactant combinations. Fenofibrate was used to investigate DC-nanomilling for formulation screening by applying a DoE-approach. The presented data also show that the results of DC-nanomilling experiments are highly comparable to the results obtained by common agitator mills. Copyright © 2017 Elsevier B.V. All rights reserved.

The effect of milling frequency on a mechanochemical organic reaction monitored by in situ Raman spectroscopy

PubMed Central

Julien, Patrick A; Malvestiti, Ivani

2017-01-01

We provide the first in situ and real-time study of the effect of milling frequency on the course of a mechanochemical organic reaction conducted using a vibratory shaker (mixer) ball mill. The use of in situ Raman spectroscopy for real-time monitoring of the mechanochemical synthesis of a 2,3-diphenylquinoxaline derivative revealed a pronounced dependence of chemical reactivity on small variations in milling frequency. In particular, in situ measurements revealed the establishment of two different regimes of reaction kinetics at different frequencies, providing tentative insight into processes of mechanical activation in organic mechanochemical synthesis. PMID:29114323

Diel changes in water chemistry in an arsenic-rich stream and treatment-pond system

USGS Publications Warehouse

Gammons, C.H.; Grant, T.M.; Nimick, D.A.; Parker, S.R.; DeGrandpre, M.D.

2007-01-01

Arsenic concentrations are elevated in surface waters of the Warm Springs Ponds Operable Unit (WSPOU), located at the head of the upper Clark Fork River Superfund site, Montana, USA. Arsenic is derived from historical deposition of smelter emissions (Mill and Willow Creeks) and historical mining and milling wastes (Silver Bow Creek). Although long-term monitoring has characterized the general seasonal and flow-related trends in As concentrations in these streams and the pond system used to treat Silver Bow Creek water, little is known about solubility controls and sorption processes that influence diel cycles in As concentrations. Diel (24-h) sampling was conducted in July 2004 and August 2005 at the outlet of the treatment ponds, at two locations along a nearby reconstructed stream channel that diverts tributary water around the ponds, and at Silver Bow Creek 2??km below the ponds. Dissolved As concentration increased up to 51% during the day at most of the stream sites, whereas little or no diel change was displayed at the treatment-pond outlet. The strong cycle in streams is explained by pH- and temperature-dependent sorption of As onto hydrous metal oxides or biofilms on the streambed. Concentrations of dissolved Ca2+ and HCO3- at the stream sites showed a diel temporal pattern opposite to that of As, and geochemical modeling supports the hypothesis that the concentrations of Ca2+ and HCO3- were controlled by precipitation of calcite during the warm afternoon hours when pH rose above 9.0. Nightly increases in dissolved Mn and Fe(II) concentrations were out of phase with concentrations of other divalent cations and are more likely explained by redox phenomena. ?? 2007 Elsevier B.V. All rights reserved.

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2012 CFR

2012-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2011 CFR

2011-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2014 CFR

2014-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2013 CFR

2013-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...