Lunar surface mining for automated acquisition of helium-3: Methods, processes, and equipment

NASA Technical Reports Server (NTRS)

Li, Y. T.; Wittenberg, L. J.

1992-01-01

In this paper, several techniques considered for mining and processing the regolith on the lunar surface are presented. These techniques have been proposed and evaluated based primarily on the following criteria: (1) mining operations should be relatively simple; (2) procedures of mineral processing should be few and relatively easy; (3) transferring tonnages of regolith on the Moon should be minimized; (4) operations outside the lunar base should be readily automated; (5) all equipment should be maintainable; and (6) economic benefit should be sufficient for commercial exploitation. The economic benefits are not addressed in this paper; however, the energy benefits have been estimated to be between 250 and 350 times the mining energy. A mobile mining scheme is proposed that meets most of the mining objectives. This concept uses a bucket-wheel excavator for excavating the regolith, several mechanical electrostatic separators for beneficiation of the regolith, a fast-moving fluidized bed reactor to heat the particles, and a palladium diffuser to separate H2 from the other solar wind gases. At the final stage of the miner, the regolith 'tailings' are deposited directly into the ditch behind the miner and cylinders of the valuable solar wind gases are transported to a central gas processing facility. During the production of He-3, large quantities of valuable H2, H2O, CO, CO2, and N2 are produced for utilization at the lunar base. For larger production of He-3 the utilization of multiple-miners is recommended rather than increasing their size. Multiple miners permit operations at more sites and provide redundancy in case of equipment failure.

Lunar surface mining for automated acquisition of helium-3: Methods, processes, and equipment

NASA Astrophysics Data System (ADS)

Li, Y. T.; Wittenberg, L. J.

1992-09-01

In this paper, several techniques considered for mining and processing the regolith on the lunar surface are presented. These techniques have been proposed and evaluated based primarily on the following criteria: (1) mining operations should be relatively simple; (2) procedures of mineral processing should be few and relatively easy; (3) transferring tonnages of regolith on the Moon should be minimized; (4) operations outside the lunar base should be readily automated; (5) all equipment should be maintainable; and (6) economic benefit should be sufficient for commercial exploitation. The economic benefits are not addressed in this paper; however, the energy benefits have been estimated to be between 250 and 350 times the mining energy. A mobile mining scheme is proposed that meets most of the mining objectives. This concept uses a bucket-wheel excavator for excavating the regolith, several mechanical electrostatic separators for beneficiation of the regolith, a fast-moving fluidized bed reactor to heat the particles, and a palladium diffuser to separate H2 from the other solar wind gases. At the final stage of the miner, the regolith 'tailings' are deposited directly into the ditch behind the miner and cylinders of the valuable solar wind gases are transported to a central gas processing facility. During the production of He-3, large quantities of valuable H2, H2O, CO, CO2, and N2 are produced for utilization at the lunar base. For larger production of He-3 the utilization of multiple-miners is recommended rather than increasing their size. Multiple miners permit operations at more sites and provide redundancy in case of equipment failure.

Statistical methods of estimating mining costs

USGS Publications Warehouse

Long, K.R.

2011-01-01

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to reestimate "Taylor's Rule" which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

30 CFR 784.25 - Return of coal processing waste to abandoned underground workings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Return of coal processing waste to abandoned... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL... RECLAMATION AND OPERATION PLAN § 784.25 Return of coal processing waste to abandoned underground workings. (a...

30 CFR 784.25 - Return of coal processing waste to abandoned underground workings.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Return of coal processing waste to abandoned... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL... RECLAMATION AND OPERATION PLAN § 784.25 Return of coal processing waste to abandoned underground workings. (a...

30 CFR 784.25 - Return of coal processing waste to abandoned underground workings.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Return of coal processing waste to abandoned... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL... RECLAMATION AND OPERATION PLAN § 784.25 Return of coal processing waste to abandoned underground workings. (a...

Solar photo-Fenton mineralization of antipyrine in aqueous solution.

PubMed

Durán, A; Monteagudo, J M; Sanmartín, I; Carrasco, A

2013-11-30

The mineralization of an aqueous solution of antipyrine (C11H12N2O), an emerging contaminant, using a solar photocatalytic oxidation process assisted with ferrioxalate was evaluated in a compound parabolic collector (CPC) pilot plant. Under the selected operating conditions ([H2O2] = 250 ppm, [Fe] = 14 ppm, pH = 2.7, and [(COOH)2·2H2O] = 80 ppm), 60% of TOC is removed just 5 min after treating an aqueous solution containing 50 ppm of antipyrine. The addition of oxalic acid up to a maximum concentration of 80 ppm significantly increases the mineralization rate during the first 15 min of the reaction. The synergism between the solar and dark H2O2/ferrioxalate process was quantified at 79%, calculated from the pseudo first-order mineralization rate constants. The operational costs due to the consumption of electrical energy, reagents and catalysts were calculated from the optimal conditions and compared with a novel sono-photocatalytic process using artificial UV-light. The results showed that the ferrioxalate-assisted solar photo-Fenton process was economically feasible, being able to achieve up to 60% mineralization with a total cost of 4.5 cent €/g TOC removed (1.1 €/m(3)). Copyright © 2013 Elsevier Ltd. All rights reserved.

30 CFR 282.29 - Reports and records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE... mining and processing activity; the number of days operations were conducted; the identity, quantity... mining. All excavations shall be shown in such manner that the volume of OCS minerals produced during a...

Raman Laser Spectrometer (RLS) on-board data processing and compression

NASA Astrophysics Data System (ADS)

Diaz, C.; Lopez, G.; Hermosilla, I.; Catalá, A.; Rodriguez, J. A.; Perez, C.; Diaz, E.

2013-09-01

The Raman Laser Spectrometer (RLS) is one of the Pasteur Payload instruments, within the ESA's Aurora Exploration Programme, ExoMars mission. Particularly, the RLS scientific objectives are as follows: identify organic compound and search for life; identify the mineral products and indicators of biologic activities; characterize mineral phases produced by water-related processes; characterize igneous minerals and their alteration products; characterise water/geochemical environment as a function of depth in the shallow subsurface. The straightforward approach of operating the instrument would result in a vast amount of spectrum images. A flexible on-board data processing concept has been designed to accommodate scientific return to the sample nature and data downlink bandwidth.

30 CFR 769.13 - Contents of petitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Contents of petitions. 769.13 Section 769.13 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR AREAS UNSUITABLE FOR MINING PETITION PROCESS FOR DESIGNATION OF FEDERAL LANDS AS UNSUITABLE FOR ALL OR CERTAIN TYPES OF SURFACE COAL MINING OPERATIONS...

Characterization of potential mineralization in Afghanistan: four permissive areas identified using imaging spectroscopy data

USGS Publications Warehouse

King, Trude V.V.; Berger, Byron R.; Johnson, Michaela R.

2014-01-01

As part of the U.S. Geological Survey and Department of Defense Task Force for Business and Stability Operations natural resources revitalization activities in Afghanistan, four permissive areas for mineralization, Bamyan 1, Farah 1, Ghazni 1, and Ghazni 2, have been identified using imaging spectroscopy data. To support economic development, the areas of potential mineralization were selected on the occurrence of selected mineral assemblages mapped using the HyMap™ data (kaolinite, jarosite, hydrated silica, chlorite, epidote, iron-bearing carbonate, buddingtonite, dickite, and alunite) that may be indicative of past mineralization processes in areas with limited or no previous mineral resource studies. Approximately 30 sites were initially determined to be candidates for areas of potential mineralization. Additional criteria and material used to refine the selection and prioritization process included existing geologic maps, Landsat Thematic Mapper data, and published literature. The HyMapTM data were interpreted in the context of the regional geologic and tectonic setting and used the presence of alteration mineral assemblages to identify areas with the potential for undiscovered mineral resources. Further field-sampling, mapping, and supporting geochemical analyses are necessary to fully substantiate and verify the specific deposit types in the four areas of potential mineralization.

40 CFR 60.674 - Monitoring of operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... compliance with the applicable PM concentration limit in Table 2 of this subpart. The revised visible... Mineral Processing Plants § 60.674 Monitoring of operations. (a) The owner or operator of any affected... repeat testing requirement specified in Table 3 of this subpart provided that the affected facility meets...

Production of Copper as a Complex Mining and Metallurgical Processing System in Polish Copper Mines of the Legnica-Glogów Copper Belt

NASA Astrophysics Data System (ADS)

Malewski, Jerzy

2017-12-01

Geological and technological conditions of Cu production in the Polish copper mines of the Legnica-Glogów Copper Belt are presented. Cu production is recognized as a technological fractal consisting of subsystems for mineral exploration, ore extraction and processing, and metallurgical treatment. Qualitative and quantitative models of these operations have been proposed, including estimation of their costs of process production. Numerical calculations of such a system have been performed, which allow optimize the system parameters according to economic criteria under variable Cu mineralization in the ore deposit. The main objective of the study is to develop forecasting tool for analysis of production efficiency in domestic copper mines based on available sources of information. Such analyses are primarily of social value, allowing for assessment of the efficiency of management of local mineral resources in the light of current technological and market constraints. At the same time, this is a concept of the system analysis method to manage deposit exploitation on operational and strategic level.

30 CFR 785.22 - In situ processing activities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false In situ processing activities. 785.22 Section... REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS FOR SPECIAL CATEGORIES OF MINING § 785.22 In situ processing... reclamation operations utilizing in situ processing activities. (b) Any application for a permit for...

30 CFR 785.22 - In situ processing activities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false In situ processing activities. 785.22 Section... REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS FOR SPECIAL CATEGORIES OF MINING § 785.22 In situ processing... reclamation operations utilizing in situ processing activities. (b) Any application for a permit for...

30 CFR 785.22 - In situ processing activities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false In situ processing activities. 785.22 Section... REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS FOR SPECIAL CATEGORIES OF MINING § 785.22 In situ processing... reclamation operations utilizing in situ processing activities. (b) Any application for a permit for...

30 CFR 785.22 - In situ processing activities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false In situ processing activities. 785.22 Section... REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS FOR SPECIAL CATEGORIES OF MINING § 785.22 In situ processing... reclamation operations utilizing in situ processing activities. (b) Any application for a permit for...

30 CFR 785.22 - In situ processing activities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false In situ processing activities. 785.22 Section... REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS FOR SPECIAL CATEGORIES OF MINING § 785.22 In situ processing... reclamation operations utilizing in situ processing activities. (b) Any application for a permit for...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

CRIB; the mineral resources data bank of the U.S. Geological Survey

USGS Publications Warehouse

Calkins, James Alfred; Kays, Olaf; Keefer, Eleanor K.

1973-01-01

The recently established Computerized Resources Information Bank (CRIB) of the U.S. Geological Survey is expected to play an increasingly important role in the study of United States' mineral resources. CRIB provides a rapid means for organizing and summarizing information on mineral resources and for displaying the results. CRIB consists of a set of variable-length records containing the basic information needed to characterize one or more mineral commodities, a mineral deposit, or several related deposits. The information consists of text, numeric data, and codes. Some topics covered are: name, location, commodity information, geology, production, reserves, potential resources, and references. The data are processed by the GIPSY program, which performs all the processing tasks needed to build, operate, and maintain the CRIB file. The sophisticated retrieval program allows the user to make highly selective searches of the files for words, parts of words, phrases, numeric data, word ranges, numeric ranges, and others, and to interrelate variables by logic statements to any degree of refinement desired. Three print options are available, or the retrieved data can be passed to another program for further processing.

Sequestering CO2 in the Built Environment

NASA Astrophysics Data System (ADS)

Constantz, B. R.

2009-12-01

Calera’s Carbonate Mineralization by Aqueous Precipitation (CMAP) technology with beneficial reuse has been called, “game-changing” by Carl Pope, Director of the Sierra Club. Calera offers a solution to the scale of the carbon problem. By capturing carbon into the built environment through carbonate mineralization, Calera provides a sound and cost-effective alternative to Geologic Sequestration and Terrestrial Sequestration. The CMAP technology permanently converts carbon dioxide into a mineral form that can be stored above ground, or used as a building material. The process produces a suite of carbonate-containing minerals of various polymorphic forms. Calera product can be substituted into blends with ordinary Portland cements and used as aggregate to produce concrete with reduced carbon, carbon neutral, or carbon negative footprints. For each ton of product produced, approximately half a ton of carbon dioxide can be sequestered using the Calera process. Coal and natural gas are composed of predominately istopically light carbon, as the carbon in the fuel is plant-derived. Thus, power plant CO2 emissions have relatively low δ13C values.The carbon species throughout the CMAP process are identified through measuring the inorganic carbon content, δ13C values of the dissolved carbonate species, and the product carbonate minerals. Measuring δ13C allows for tracking the flue gas CO2 throughout the capture process. Initial analysis of the capture of propane flue gas (δ13C ˜ -25 ‰) with seawater (δ13C ˜ -10 ‰) and industrial brucite tailings from a retired magnesium oxide plant in Moss Landing, CA (δ13C ˜ -7 ‰ from residual calcite) produced carbonate mineral products with a δ13C value of ˜ -20 ‰. This isotopically light carbon, transformed from flue gas to stable carbonate minerals, can be transferred and tracked through the capture process, and finally to the built environment. CMAP provides an economical solution to global warming by producing a usable product. While the cost of this process may, in some cases, exceed the selling price of the resultant materials, the value produced combined with available carbon credits makes this CMAP technology economically and environmentally sustainable. Calera operates a pilot plant in Moss Landing, CA, which is within the Monterey Bay Marine Sanctuary. The pilot plant is complete with a coal-fired burner simulator (CFBS) and laboratory. During operation, seawater is drawn in and subsequently combined with a variety of natural and manufactured minerals. Propane or coal flue gas from the CFBS is then contacted with the slurry suspension. The precipitated minerals are separated from the seawater and are further processed to produce cement or other building materials. After the seawater flows through the Calera process, it is returned to the ocean largely unchanged, with the exception of being calcium and magnesium depleted. An overview of the process, reporting the δ13C values throughout the CMAP process, along with the risk involved in changing regulations will be presented.

Plan for Management of Mineral Assess on Native Tribal Lands and for Formation of a Fully Integrated Natural Gas and Oil Exploration and Production Company

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blechner, Michael H.; Carroll, Herbert B.; Johnson, William I.

1999-04-27

This report describes a plan for Native American tribes to assume responsibility for and operation of tribal mineral resources using the Osage Tribe as an example. Under this plan, the tribal council select and employ a qualified Director to assume responsibility for management of their mineral reservations. The procurement process should begin with an application for contracting to the Bureau of Indian Affairs. Under this plan, the Director will develop strategies to increase income by money management and increasing exploitation of natural gas, oil, and other minerals.

Stable isotope and mineralogical investigation of the genesis of amethyst geodes in the Los Catalanes gemological district, Uruguay, southernmost Paraná volcanic province

NASA Astrophysics Data System (ADS)

Duarte, Lauren C.; Hartmann, Leo A.; Ronchi, Luiz H.; Berner, Zsolt; Theye, Thomas; Massonne, Hans J.

2011-03-01

Stable isotopes (C, O, S) and mineralogical studies of the world-class amethyst-geode deposits of the Los Catalanes gemological district, Uruguay, constrain processes operative during mineral deposition. The mineralized basaltic andesites from the Cretaceous Paraná volcanic province are intensely altered to zeolites (clinoptilolite) and clay minerals. Variations in the δ18O values of silica minerals in geodes (chalcedony, quartz, and amethyst) are much larger and the values generally somewhat lower (21.2-31.5‰) in the Uruguayan deposits than in the Ametista do Sul area of southern Brazil. The range of δ34S values (-15.0 to -0.3‰) of altered basaltic rocks requires (in addition to sulfur of magmatic origin) the involvement of 34S-depleted sedimentary sulfur from bacterial sulfate reduction. The results delimit the mineralizing processes to a post-eruption environment characterized by low temperature and strong interaction of the lava flows with meteoric water.

Process Metallurgy an Enabler of Resource Efficiency: Linking Product Design to Metallurgy in Product Centric Recycling

NASA Astrophysics Data System (ADS)

Reuter, Markus; van Schaik, Antoinette

In this paper the link between process metallurgy, classical minerals processing, product centric recycling and urban/landfill mining is discussed. The depth that has to be achieved in urban mining and recycling must glean from the wealth of theoretical knowledge and insight that have been developed in the past in minerals and metallurgical processing. This background learns that recycling demands a product centric approach, which considers simultaneously the multi-material interactions in man-made complex `minerals'. Fast innovation in recycling and urban mining can be achieved by further evolving from this well developed basis, evolving the techniques and tools that have been developed over the years. This basis has already been used for many years to design, operate and control industrial plants for metal production. This has been the basis for Design for Recycling rules for End-of-Life products. Using, among others, the UNEP Metal Recycling report as a basis (authors are respectively Lead and Main authors of report), it is demonstrated that a common theoretical basis as developed in metallurgy and minerals processing can help much to level the playing field between primary processing, secondary processing, recycling, and urban/landfill mining and product design hence enhancing resource efficiency. Thus various scales of detail link product design with metallurgical process design and its fundamentals.

Pseudophasic extraction method for the separation of ultra-fine minerals

DOEpatents

Chaiko, David J.

2002-01-01

An improved aqueous-based extraction method for the separation and recovery of ultra-fine mineral particles. The process operates within the pseudophase region of the conventional aqueous biphasic extraction system where a low-molecular-weight, water soluble polymer alone is used in combination with a salt and operates within the pseudo-biphase regime of the conventional aqueous biphasic extraction system. A combination of low molecular weight, mutually immiscible polymers are used with or without a salt. This method is especially suited for the purification of clays that are useful as rheological control agents and for the preparation of nanocomposites.

Innovative treatment trains of bottom ash (BA) from municipal solid waste incineration (MSWI) in Germany.

PubMed

Holm, Olaf; Simon, Franz-Georg

2017-01-01

The industrial sector of bottom ash (BA) treatment from municipal solid waste incineration (MSWI) in Germany is currently changing. In order to increase the recovery rates of metals or to achieve a higher quality of mineral aggregates derived from BA, new procedures have been either implemented to existing plants or completely new treatment plants have been built recently. Three treatment trains, which are designated as entire sequences of selected processing techniques of BA, are introduced and compared. One treatment train is mainly characterized by usage of a high speed rotation accelerator whereas another is operating completely without crushing. In the third treatment train the BA is processed wet directly after incineration. The consequences for recovered metal fractions and the constitution of remaining mineral aggregates are discussed in the context of legislative and economical frameworks. Today the recycling or disposal options of mineral residues still have a high influence on the configuration and the operation mode of the treatment trains of BA despite of the high value of recovered metals. Copyright © 2016 Elsevier Ltd. All rights reserved.

36 CFR 292.67 - Operating plan approval-outstanding mineral rights.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-outstanding mineral rights. 292.67 Section 292.67 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.67 Operating plan approval—outstanding mineral rights. (a) Upon receipt of an operating plan...

36 CFR 292.67 - Operating plan approval-outstanding mineral rights.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-outstanding mineral rights. 292.67 Section 292.67 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.67 Operating plan approval—outstanding mineral rights. (a) Upon receipt of an operating plan...

36 CFR 292.67 - Operating plan approval-outstanding mineral rights.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-outstanding mineral rights. 292.67 Section 292.67 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.67 Operating plan approval—outstanding mineral rights. (a) Upon receipt of an operating plan...

36 CFR 292.67 - Operating plan approval-outstanding mineral rights.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-outstanding mineral rights. 292.67 Section 292.67 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.67 Operating plan approval—outstanding mineral rights. (a) Upon receipt of an operating plan...

Hazard recognition in mining: A psychological perspective. Information circular/1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perdue, C.W.; Kowalski, K.M.; Barrett, E.A.

1995-07-01

This U.S. Bureau of Mines report considers, from a psychological perspective, the perceptual process by which miners recognize and respond to mining hazards. It proposes that if the hazard recognition skills of miners can be improved, mining accidents may be reduced to a significant degree. Prior studies of hazard perception in mining are considered, as are relevant studies from investigations of military target identification, pilot and gunnery officer training, transportation safety, automobile operator behavior, as well as research into sensory functioning and visual information processing. A general model of hazard perception is introduced, and selected concepts from the psychology ofmore » perception that are applicable to the detection of mining hazards are reviewed. Hazard recognition is discussed as a function of the perceptual cues available to the miner as well as the cognitive resources and strategies employed by the miner. The development of expertise in resonding to hazards is related to individual differences in the experience, aptitude, and personality of the worker. Potential applications to miner safety and training are presented.« less

Application of computational methods to analyse and investigate physical and chemical processes of high-temperature mineralizing of condensed substances in gas stream

NASA Astrophysics Data System (ADS)

Markelov, A. Y.; Shiryaevskii, V. L.; Kudrinskiy, A. A.; Anpilov, S. V.; Bobrakov, A. N.

2017-11-01

A computational method of analysis of physical and chemical processes of high-temperature mineralizing of low-level radioactive waste in gas stream in the process of plasma treatment of radioactive waste in shaft furnaces was introduced. It was shown that the thermodynamic simulation method allows fairly adequately describing the changes in the composition of the pyrogas withdrawn from the shaft furnace at different waste treatment regimes. This offers a possibility of developing environmentally and economically viable technologies and small-sized low-cost facilities for plasma treatment of radioactive waste to be applied at currently operating nuclear power plants.

36 CFR 292.66 - Operating plan requirements-outstanding mineral rights.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-outstanding mineral rights. 292.66 Section 292.66 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.66 Operating plan requirements—outstanding mineral rights. (a) Proposals for mineral...

36 CFR 292.66 - Operating plan requirements-outstanding mineral rights.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-outstanding mineral rights. 292.66 Section 292.66 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.66 Operating plan requirements—outstanding mineral rights. (a) Proposals for mineral...

36 CFR 292.66 - Operating plan requirements-outstanding mineral rights.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-outstanding mineral rights. 292.66 Section 292.66 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.66 Operating plan requirements—outstanding mineral rights. (a) Proposals for mineral...

36 CFR 292.66 - Operating plan requirements-outstanding mineral rights.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-outstanding mineral rights. 292.66 Section 292.66 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral Rights § 292.66 Operating plan requirements—outstanding mineral rights. (a) Proposals for mineral...

Individual Learning Route as a Way of Highly Qualified Specialists Training for Extraction of Solid Commercial Minerals Enterprises

NASA Astrophysics Data System (ADS)

Oschepkova, Elena; Vasinskaya, Irina; Sockoluck, Irina

2017-11-01

In view of changing educational paradigm (adopting of two-tier system of higher education concept - undergraduate and graduate programs) a need of using of modern learning and information and communications technologies arises putting into practice learner-centered approaches in training of highly qualified specialists for extraction and processing of solid commercial minerals enterprises. In the unstable market demand situation and changeable institutional environment, from one side, and necessity of work balancing, supplying conditions and product quality when mining-and-geological parameters change, from the other side, mining enterprises have to introduce and develop the integrated management process of product and informative and logistic flows under united management system. One of the main limitations, which keeps down the developing process on Russian mining enterprises, is staff incompetence at all levels of logistic management. Under present-day conditions extraction and processing of solid commercial minerals enterprises need highly qualified specialists who can do self-directed researches, develop new and improve present arranging, planning and managing technologies of technical operation and commercial exploitation of transport and transportation and processing facilities based on logistics. Learner-centered approach and individualization of the learning process necessitate the designing of individual learning route (ILR), which can help the students to realize their professional facilities according to requirements for specialists for extraction and processing of solid commercial minerals enterprises.

Hydrogeochemistry and microbiology of mine drainage: An update

USGS Publications Warehouse

Nordstrom, D. Kirk; Blowes, D.W; Ptacek, C.J.

2015-01-01

The extraction of mineral resources requires access through underground workings, or open pit operations, or through drillholes for solution mining. Additionally, mineral processing can generate large quantities of waste, including mill tailings, waste rock and refinery wastes, heap leach pads, and slag. Thus, through mining and mineral processing activities, large surface areas of sulfide minerals can be exposed to oxygen, water, and microbes, resulting in accelerated oxidation of sulfide and other minerals and the potential for the generation of low-quality drainage. The oxidation of sulfide minerals in mine wastes is accelerated by microbial catalysis of the oxidation of aqueous ferrous iron and sulfide. These reactions, particularly when combined with evaporation, can lead to extremely acidic drainage and very high concentrations of dissolved constituents. Although acid mine drainage is the most prevalent and damaging environmental concern associated with mining activities, generation of saline, basic and neutral drainage containing elevated concentrations of dissolved metals, non-metals, and metalloids has recently been recognized as a potential environmental concern. Acid neutralization reactions through the dissolution of carbonate, hydroxide, and silicate minerals and formation of secondary aluminum and ferric hydroxide phases can moderate the effects of acid generation and enhance the formation of secondary hydrated iron and aluminum minerals which may lessen the concentration of dissolved metals. Numerical models provide powerful tools for assessing impacts of these reactions on water quality.

Optimization of Mineral Separator for Recovery of Total Heavy Minerals of Bay of Bengal using Central Composite Design

NASA Astrophysics Data System (ADS)

Routray, Sunita; Swain, Ranjita; Rao, Raghupatruni Bhima

2017-04-01

The present study is aimed at investigating the optimization of a mineral separator for processing of beach sand minerals of Bay of Bengal along Ganjam-Rushikulya coast. The central composite design matrix and response surface methodology were applied in designing the experiments to evaluate the interactive effects of the three most important operating variables, such as feed quantity, wash water rate and Shake amplitude of the deck. The predicted values were found to be in good agreement with the experimental values (R2 = 0.97 for grade and 0.98 for recovery). To understand the impact of each variable, three dimensional (3D) plots were also developed for the estimated responses.

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

Coastal deposits of heavy mineral sands; Global significance and US resources

USGS Publications Warehouse

Van Gosen, Bradley S.; Bleiwas, Donald I.; Bedinger, George M.; Ellefsen, Karl J.; Shah, Anjana K.

2016-01-01

Ancient and modern coastal deposits of heavy mineral sands (HMS) are the principal source of several heavy industrial minerals, with mining and processing operations on every continent except Antarctica. For example, HMS deposits are the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, obtained from the minerals ilmenite (Fe2+TiO3), rutile (TiO2) and leucoxene (an alteration product of ilmenite). HMS deposits are also the principal source of zircon (ZrSiO4), from which zirconium dioxide (ZrO2) is obtained for uses mostly in refractory products. Sometimes monazite [(Ce,La,Nd,Th)PO4] is recovered as a byproduct mineral, sought for its rare earth elements and thorium (Ault and others, 2016; Sengupta and Van Gosen, 2016; Van Gosen and Tulsidas, 2016). 

30 CFR 282.31 - Suspension of production or other operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Suspension of production or other operations. 282.31 Section 282.31 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR Obligations and Responsibilities of Lessees § 282.31...

Natural thorium resources and recovery: Options and impacts

USGS Publications Warehouse

Ault, Timothy; Van Gosen, Bradley S.; Krahn, Steven; Croff, Allen

2016-01-01

This paper reviews the front end of the thorium fuel cycle, including the extent and variety of thorium deposits, the potential sources of thorium production, and the physical and chemical technologies required to isolate and purify thorium. Thorium is frequently found within rare earth element–bearing minerals that exist in diverse types of mineral deposits, often in conjunction with other minerals mined for their commercial value. It may be possible to recover substantial quantities of thorium as a by-product from active titanium, uranium, tin, iron, and rare earth mines. Incremental physical and chemical processing is required to obtain a purified thorium product from thorium minerals, but documented experience with these processes is extensive, and incorporating thorium recovery should not be overly challenging. The anticipated environmental impacts of by-product thorium recovery are small relative to those of uranium recovery since existing mining infrastructure utilization avoids the opening and operation of new mines and thorium recovery removes radionuclides from the mining tailings.

The microbiology of biomining: development and optimization of mineral-oxidizing microbial consortia.

PubMed

Rawlings, Douglas E; Johnson, D Barrie

2007-02-01

Biomining, the use of micro-organisms to recover precious and base metals from mineral ores and concentrates, has developed into a successful and expanding area of biotechnology. While careful considerations are made in the design and engineering of biomining operations, microbiological aspects have been subjected to far less scrutiny and control. Biomining processes employ microbial consortia that are dominated by acidophilic, autotrophic iron- or sulfur-oxidizing prokaryotes. Mineral biooxidation takes place in highly aerated, continuous-flow, stirred-tank reactors or in irrigated dump or heap reactors, both of which provide an open, non-sterile environment. Continuous-flow, stirred tanks are characterized by homogeneous and constant growth conditions where the selection is for rapid growth, and consequently tank consortia tend to be dominated by two or three species of micro-organisms. In contrast, heap reactors provide highly heterogeneous growth environments that change with the age of the heap, and these tend to be colonized by a much greater variety of micro-organisms. Heap micro-organisms grow as biofilms that are not subject to washout and the major challenge is to provide sufficient biodiversity for optimum performance throughout the life of a heap. This review discusses theoretical and pragmatic aspects of assembling microbial consortia to process different mineral ores and concentrates, and the challenges for using constructed consortia in non-sterile industrial-scale operations.

75 FR 70279 - Agency Information Collection Activities: Submitted for Office of Management and Budget Review...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-17

...-length AUDIT PROCESS transmission contracts, See Note. production and operating agreements and related... production method. 1206.458(c)(1)(iv) and (c)(2)(vi).. Submit arm's-length washing AUDIT PROCESS contracts...). The Secretary is required by various laws to manage mineral resource production from Federal and...

40 CFR 436.152 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

40 CFR 436.142 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

40 CFR 436.132 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

40 CFR 436.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY.... The height difference between the maximum safe surge capacity level and the normal operating level...

To build a mine: Prospect to product

NASA Technical Reports Server (NTRS)

Gertsch, Richard E.

1992-01-01

The terrestrial definition of ore is a quantity of earth materials containing a mineral that can be extracted at a profit. While a space-based resource-gathering operation may well be driven by other motives, such an operation should have the most favorable cost-benefit ratio possible. To this end, principles and procedures already tested by the stringent requirements of the profit motive should guide the selection, design, construction, and operation of a space-based mine. Proceeding from project initiation to a fully operational mine requires several interacting and overlapping steps, which are designed to facilitate the decision process and insure economic viability. The steps to achieve a fully operational mine are outlined. Presuming that the approach to developing nonterrestrial resources will parallel that for developing mineral resources on Earth, we can speculate on some of the problems associated with developing lunar and asteroidal resources. The baseline for our study group was a small lunar mine and oxygen extraction facility. The development of this facility is described in accordance with the steps outlined.

25 CFR 215.23a - Suspension of operations and production on leases for minerals other than oil and gas.

Code of Federal Regulations, 2010 CFR

2010-04-01

... minerals other than oil and gas. 215.23a Section 215.23a Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.23a Suspension of operations and production on leases for minerals other than oil and gas. The provisions of...

Soil Organic Carbon and Its interaction with Minerals in Two Hillslopes with Different Climates and Erosion Processes

NASA Astrophysics Data System (ADS)

Wang, X.; Yoo, K.; Wackett, A. A.; Gutknecht, J.; Amundson, R.; Heimsath, A. M.

2017-12-01

Climate and topography have been widely recognized as important factors regulating soil organic carbon (SOC) dynamics but their interactive effects on SOC storage and its pools remain poorly constrained. Here we aimed to evaluate SOC storages and carbon-mineral interactions along two hillslope transects with moderately different climates (MAP: 549 mm vs. 816 mm) in Southeastern Australia. We sampled soil along the convex (eroding)-to-convergent (depositional) continuum at each hillslope transect and conducted size and density fractionation of these samples. In responses to the difference in climate factor, SOC inventories of eroding soils were twice as large at the wetter site compared with the drier site but showed little difference between two sites in depositional soils. These trends in SOC inventories were primarily controlled by SOC concentrations and secondarily by soil thicknesses. Similar patterns were observed for mineral associated organic carbon (MOC), and the abundances of MOC were controlled by the two independently operating processes affecting MOC concentration and fine-heavy fraction minerals. The contents and species of secondary clay and iron oxide minerals, abundances of particulate organic carbon, and bioturbation affected MOC concentrations. In contrast, the abundances of fine-heavy fraction minerals were impacted by erosion mechanisms that uniquely responded to regional- and micro- climate conditions. Consequently, topographic influences on SOC inventories and carbon-mineral interactions were more strongly pronounced in the drier climate where vegetation and erosion mechanisms were sensitive to microclimate. Our results highlight the significance of understanding topography and erosional processes in capturing climatic effects on soil carbon dynamics.

40 CFR 436.382 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... capacity level and the normal operating level must be greater than the inches of rain representing the 10...

40 CFR 436.72 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... level and the normal operating level must be greater than the inches of rain representing the 10-year...

78 FR 35602 - Coeur d'Alene Basin Restoration Plan, Kootenai, Shoshone and Benewah Counties, Idaho

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-13

... zinc mining areas in the United States. The majority of mining and mineral processing in the Basin... operations contain metals, including lead, zinc, cadmium, and arsenic. A significant portion of these wastes...

Mineralizing urban net-zero water treatment: Field experience for energy-positive water management.

PubMed

Wu, Tingting; Englehardt, James D

2016-12-01

An urban net-zero water treatment system, designed for energy-positive water management, 100% recycle of comingled black/grey water to drinking water standards, and mineralization of hormones and other organics, without production of concentrate, was constructed and operated for two years, serving an occupied four-bedroom, four-bath university residence hall apartment. The system comprised septic tank, denitrifying membrane bioreactor (MBR), iron-mediated aeration (IMA) reactor, vacuum ultrafilter, and peroxone or UV/H 2 O 2 advanced oxidation, with 14% rainwater make-up and concomitant discharge of 14% of treated water (ultimately for reuse in irrigation). Chemical oxygen demand was reduced to 12.9 ± 3.7 mg/L by MBR and further decreased to below the detection limit (<0.7 mg/L) by IMA and advanced oxidation treatment. The process produced a mineral water meeting 115 of 115 Florida drinking water standards that, after 10 months of recycle operation with ∼14% rainwater make-up, had a total dissolved solids of ∼500 mg/L, pH 7.8 ± 0.4, turbidity 0.12 ± 0.06 NTU, and NO 3 -N concentration 3.0 ± 1.0 mg/L. None of 97 hormones, personal care products, and pharmaceuticals analyzed were detected in the product water. For a typical single-home system with full occupancy, sludge pumping is projected on a 12-24 month cycle. Operational aspects, including disinfection requirements, pH evolution through the process, mineral control, advanced oxidation by-products, and applicability of point-of-use filters, are discussed. A distributed, peroxone-based NZW management system is projected to save more energy than is consumed in treatment, due largely to retention of wastewater thermal energy. Recommendations regarding design and operation are offered. Copyright © 2016 Elsevier Ltd. All rights reserved.

Applications of Geomatics in Surface Mining

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Górniak-Zimroz, Justyna; Milczarek, Wojciech; Pactwa, Katarzyna

2017-12-01

In terms of method of extracting mineral from deposit, mining can be classified into: surface, underground, and borehole mining. Surface mining is a form of mining, in which the soil and the rock covering the mineral deposits are removed. Types of surface mining include mainly strip and open-cast methods, as well as quarrying. Tasks associated with surface mining of minerals include: resource estimation and deposit documentation, mine planning and deposit access, mine plant development, extraction of minerals from deposits, mineral and waste processing, reclamation and reclamation of former mining grounds. At each stage of mining, geodata describing changes occurring in space during the entire life cycle of surface mining project should be taken into consideration, i.e. collected, analysed, processed, examined, distributed. These data result from direct (e.g. geodetic) and indirect (i.e. remote or relative) measurements and observations including airborne and satellite methods, geotechnical, geological and hydrogeological data, and data from other types of sensors, e.g. located on mining equipment and infrastructure, mine plans and maps. Management of such vast sources and sets of geodata, as well as information resulting from processing, integrated analysis and examining such data can be facilitated with geomatic solutions. Geomatics is a discipline of gathering, processing, interpreting, storing and delivering spatially referenced information. Thus, geomatics integrates methods and technologies used for collecting, management, processing, visualizing and distributing spatial data. In other words, its meaning covers practically every method and tool from spatial data acquisition to distribution. In this work examples of application of geomatic solutions in surface mining on representative case studies in various stages of mine operation have been presented. These applications include: prospecting and documenting mineral deposits, assessment of land accessibility for a potential large-scale surface mining project, modelling mineral deposit (granite) management, concept of a system for management of conveyor belt network technical condition, project of a geoinformation system of former mining terrains and objects, and monitoring and control of impact of surface mining on mine surroundings with satellite radar interferometry.

Controls on Mississippi Valley-Type Zn-Pb mineralization in Behabad district, Central Iran: Constraints from spatial and numerical analyses

NASA Astrophysics Data System (ADS)

Parsa, Mohammad; Maghsoudi, Abbas

2018-04-01

The Behabad district, located in the central Iranian microcontinent, contains numerous epigenetic stratabound carbonate-hosted Zn-Pb ore bodies. The mineralizations formed as fault, fracture and karst fillings in the Permian-Triassic formations, especially in Middle Triassic dolostones, and comprise mainly non-sulfides zinc ores. These are all interpreted as Mississippi Valley-type (MVT) base metal deposits. From an economic geological point of view, it is imperative to recognize the processes that have plausibly controlled the emplacement of MVT Zn-Pb mineralization in the Behabad district. To address the foregoing issue, analyses of the spatial distribution of mineral deposits comprising fry and fractal techniques and analysis of the spatial association of mineral deposits with geological features using distance distribution analysis were applied to assess the regional-scale processes that could have operated in the distribution of MVT Zn-Pb deposits in the district. The obtained results based on these analytical techniques show the main trends of the occurrences are NW-SE and NE-SW, which are parallel or subparallel to the major northwest and northeast trending faults, supporting the idea that these particular faults could have acted as the main conduits for transport of mineral-bearing fluids. The results of these analyses also suggest that Permian-Triassic brittle carbonate sedimentary rocks have served as the lithological controls on MVT mineralization in the Behabad district as they are spatially and temporally associated with mineralization.

30 CFR 250.1600 - Performance standard.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Performance standard. 250.1600 Section 250.1600 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1600 Performance standard. Operations to...

NDCEE Annual Technologies Publication

DTIC Science & Technology

2003-04-01

Engineering Center TBP Thermophilic (Biological) Process TCP Trivalent chromium pretreatment 3-D Three-dimensional TNT 2,4,6 trinitrotoluene TTU Transit-Time...to be able to restore worn, improperly machined or salvaged service parts. Trivalent Chromium Plating: This process eliminates the use of chromic...acid, thereby reducing health risks to operators. Trivalent chromium forms insoluble mineral precipitates in groundwater, which eliminates the chemical

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Mineral material operations. 292.68 Section 292.68 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material...

30 CFR 48.27 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2010 CFR

2010-07-01

... RETRAINING OF MINERS Training and Retraining of Miners Working at Surface Mines and Surface Areas of... shall not be required for miners who have been trained and who have demonstrated safe operating... required for miners who have performed the new work tasks and who have demonstrated safe operating...

25 CFR 225.32 - Permission to start operations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Permission to start operations. 225.32 Section 225.32 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS OIL AND GAS, GEOTHERMAL, AND SOLID MINERALS AGREEMENTS Minerals Agreements § 225.32 Permission to start operations. (a) No...

25 CFR 225.32 - Permission to start operations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Permission to start operations. 225.32 Section 225.32 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS OIL AND GAS, GEOTHERMAL, AND SOLID MINERALS AGREEMENTS Minerals Agreements § 225.32 Permission to start operations. (a) No...

30 CFR 250.259 - What sulphur operations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What sulphur operations information must accompany the DPP or DOCD? 250.259 Section 250.259 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Information Contents of Development and Production Plans (dpp) and Development Operations Coordination...

30 CFR 250.611 - Traveling-block safety device.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Traveling-block safety device. 250.611 Section 250.611 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... operation weekly and after each drill-line slipping operation. The results of the operational check shall be...

SELENIUM TREATMENT/REMOVAL ALTERNATIVES DEMONSTRATION PROJECT - MINE WASTE TECHNOLOGY PROGRAM ACTIVITY III, PROJECT 20

EPA Science Inventory

This document is the final report for EPA's Mine WAste Technology Program (MWTP) Activity III, Project 20--Selenium Treatment/Removal Alternatives Demonstration project. Selenium contamination originates from many sources including mining operations, mineral processing, abandoned...

Zirconium and hafnium

USGS Publications Warehouse

Jones, James V.; Piatak, Nadine M.; Bedinger, George M.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Zirconium and hafnium are corrosion-resistant metals that are widely used in the chemical and nuclear industries. Most zirconium is consumed in the form of the main ore mineral zircon (ZrSiO4, or as zirconium oxide or other zirconium chemicals. Zirconium and hafnium are both refractory lithophile elements that have nearly identical charge, ionic radii, and ionic potentials. As a result, their geochemical behavior is generally similar. Both elements are classified as incompatible because they have physical and crystallochemical properties that exclude them from the crystal lattices of most rock-forming minerals. Zircon and another, less common, ore mineral, baddeleyite (ZrO2), form primarily as accessory minerals in igneous rocks. The presence and abundance of these ore minerals in igneous rocks are largely controlled by the element concentrations in the magma source and by the processes of melt generation and evolution. The world’s largest primary deposits of zirconium and hafnium are associated with alkaline igneous rocks, and, in one locality on the Kola Peninsula of Murmanskaya Oblast, Russia, baddeleyite is recovered as a byproduct of apatite and magnetite mining. Otherwise, there are few primary igneous deposits of zirconium- and hafnium-bearing minerals with economic value at present. The main ore deposits worldwide are heavy-mineral sands produced by the weathering and erosion of preexisting rocks and the concentration of zircon and other economically important heavy minerals, such as ilmenite and rutile (for titanium), chromite (for chromium), and monazite (for rare-earth elements) in sedimentary systems, particularly in coastal environments. In coastal deposits, heavy-mineral enrichment occurs where sediment is repeatedly reworked by wind, waves, currents, and tidal processes. The resulting heavy-mineral-sand deposits, called placers or paleoplacers, preferentially form at relatively low latitudes on passive continental margins and supply 100 percent of the world’s zircon. Zircon makes up a relatively small percentage of the economic heavy minerals in most deposits and is produced primarily as a byproduct of heavy-mineral-sand mining for titanium minerals.From 2003 to 2012, world zirconium mineral concentrates production increased by more than 40 percent, and Australia and South Africa were the leading producers. Global consumption of zirconium mineral concentrates generally increased during the same time period, largely as a result of increased demand in developing economies in Asia and the Middle East. Global demand weakened in 2012, causing a decrease in world production of zirconium mineral concentrates and delaying the development of several new mining projects. Global consumption is expected to increase in the future, however, as demand from the ceramics, chemicals, and metals industries increases (driven by renewed growth in developing economies) and demand for zirconium and hafnium metal increases (driven by the construction and operation of new nuclear powerplants).The behaviors of zirconium and hafnium in the environment are very similar to one another in that most zirconium- and hafnium-bearing minerals have limited solubility and reactivity. Anthropogenic sources of zirconium, and likely hafnium, are from industrial zirconium-containing byproducts and emissions from the processing of sponge zirconium, and exposure to the general population from these sources is small. Zirconium and hafnium are likely not essential to human health and generally are considered to be of low toxicity to humans. The main exposure risks are associated with industrial inhalation and dermal exposure. Because of the low solubility of zirconium and hafnium, ecological health concerns in the aquatic environment and in soils are minimal. Heavy-mineral-sand mining may lead to increased erosion rates when the mining is managed improperly. In addition, surface mining requires removal of the overlying organic soil layer and produces waste material that includes tailings and slimes. The soil removal and mining activity disturbs the surrounding ecosystem and alters the character of the landscape. Dry mineral separation processes create high amounts of airborne dust, whereas wet mineral separation processes do not. In operations that restore the landscape to pre-mining conditions, the volume of waste and the impact on the landscape may be relatively temporary.

30 CFR 62.180 - Training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Training. 62.180 Section 62.180 Mineral... OCCUPATIONAL NOISE EXPOSURE § 62.180 Training. (a) The mine operator must, within 30 days of a miner's enrollment into a hearing conservation program, provide the miner with training. The mine operator must give...

Effect of Natural Mineral on Methane Production and Process Stability During Semi-Continuous Mono-Digestion of Maize Straw.

PubMed

González-Suárez, A; Pereda-Reyes, I; Pozzi, E; da Silva, A José; Oliva-Merencio, D; Zaiat, M

2016-04-01

The effect of natural mineral on the mono-digestion of maize straw was evaluated in continuously stirred tank reactors (CSTRs) at 38 °C. Different strategies of mineral addition were studied. The organic loading rate (OLR) was varied from 0.5 to 2.5 g volatile solid (VS) L(-1) d(-1). A daily addition of 1 g mineral L(-1) in reactor 2 (R2) diminished the methane production by about 11 % with respect to the initial phase. However, after a gradual addition of mineral, an average methane yield of 257 NmL CH4 g VS(-1) was reached and the methane production was enhanced by 30 % with regard to R1. An increase in the frequency of mineral addition did not enhance the methane production. The archaeal community was more sensitive to the mineral than the bacterial population whose similarity stayed high between R1 and R2. Significant difference in methane yield was found for both reactors throughout the operation.

From urban municipalities to polar bioremediation: the characterisation and contribution of biogenic minerals for water treatment.

PubMed

Freidman, Benjamin L; Northcott, Kathy A; Thiel, Peta; Gras, Sally L; Snape, Ian; Stevens, Geoff W; Mumford, Kathryn A

2017-06-01

Minerals of biological origin have shown significant potential for the separation of contaminants from water worldwide. This study details the contribution of biologically derived minerals to water treatment operations, with a focus on filtration media from urban municipalities and remote cold regions. The results support biofilm-embedded iron and manganese to be the building blocks of biogenic mineral development on activated carbon and nutrient-amended zeolites. The presence of similar iron and manganese oxidising bacterial species across all filter media supports the analogous morphologies of biogenic minerals between sites and suggests that biological water treatment processes may be feasible across a range of climates. This is the first time the stages of biogenic mineral formation have been aligned with comprehensive imaging of the biofilm community and bacterial identification; especially with respect to cold regions. Where biogenic mineral formation occurs on filter media, the potential exists for enhanced adsorption for a range of organic and inorganic contaminants and improved longevity of filter media beyond the adsorption or exchange capacities of the raw material.

Characterization of flotation color by machine vision

NASA Astrophysics Data System (ADS)

Siren, Ari

1999-09-01

Flotation is the most common industrial method by which valuable minerals are separated from waste rock after crushing and grinding the ore. For process control, flotation plants and devices are equipped with conventional and specialized sensors. However, certain variables are left to the visual observation of the operator, such as the color of the froth and the size of the bubbles in the froth. The ChaCo-Project (EU-Project 24931) was launched in November 1997. In this project a measuring station was built at the Pyhasalmi flotation plant. The system includes an RGB camera and a spectral color measuring instrument for the color inspection of the flotation. The RGB camera or visible spectral range is also measured to compare the operators' comments on the color of the froth relating to the sphalerite concentration and the process balance. Different dried mineral (sphalerite) ratios were studied with iron pyrite to find out about the minerals' typical spectral features. The correlation between sphalerite spectral reflectance and sphalerite concentration over various wavelengths are used to select the proper camera system with filters or to compare the results with the color information from the RGB camera. Various machine vision candidate techniques are discussed for this application and the preprocessed information of the dried mineral colors is used and adapted to the online measuring station. Moving froth bubbles produce total reflections, disturbing the color information. Polarization filters are used and the results are reported. Also the reflectance outside the visible light is studied and reported.

Comparative study of UV/TiO2, UV/ZnO and photo-Fenton processes for the organic reactive dye degradation in aqueous solution.

PubMed

Peternel, Igor T; Koprivanac, Natalija; Bozić, Ana M Loncarić; Kusić, Hrvoje M

2007-09-05

In this study advanced oxidation processes (AOPs), UV/TiO(2), UV/ZnO and photo-Fenton, were applied in order to degrade C.I. Reactive Red 45 (RR45) dye in aqueous solution. The effects of key operating parameters, such as initial pH, catalyst and hydrogen peroxide dosage as well as the effect of initial dye concentration on decolorization and mineralization extents were studied. Primary objective was to determine the optimal conditions for each of the processes. The influence of added zeolite on the process efficiency was also studied. UV/vis spectrophotometric and total organic carbon (TOC) measurements were performed for determination of decolorization and mineralization extents. It has been found that photo-Fenton process was the most efficient with 74.2% TOC removal and complete color removal achieved after a 1h treatment.

Coal liquefaction process

DOEpatents

Karr, Jr., Clarence

1977-04-19

An improved coal liquefaction process is provided which enables conversion of a coal-oil slurry to a synthetic crude refinable to produce larger yields of gasoline and diesel oil. The process is characterized by a two-step operation applied to the slurry prior to catalytic desulfurization and hydrogenation in which the slurry undergoes partial hydrogenation to crack and hydrogenate asphaltenes and the partially hydrogenated slurry is filtered to remove minerals prior to subsequent catalytic hydrogenation.

Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

NASA Astrophysics Data System (ADS)

Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

2017-12-01

Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

Native Language Processing using Exegy Text Miner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Compton, J

2007-10-18

Lawrence Livermore National Laboratory's New Architectures Testbed recently evaluated Exegy's Text Miner appliance to assess its applicability to high-performance, automated native language analysis. The evaluation was performed with support from the Computing Applications and Research Department in close collaboration with Global Security programs, and institutional activities in native language analysis. The Exegy Text Miner is a special-purpose device for detecting and flagging user-supplied patterns of characters, whether in streaming text or in collections of documents at very high rates. Patterns may consist of simple lists of words or complex expressions with sub-patterns linked by logical operators. These searches are accomplishedmore » through a combination of specialized hardware (i.e., one or more field-programmable gates arrays in addition to general-purpose processors) and proprietary software that exploits these individual components in an optimal manner (through parallelism and pipelining). For this application the Text Miner has performed accurately and reproducibly at high speeds approaching those documented by Exegy in its technical specifications. The Exegy Text Miner is primarily intended for the single-byte ASCII characters used in English, but at a technical level its capabilities are language-neutral and can be applied to multi-byte character sets such as those found in Arabic and Chinese. The system is used for searching databases or tracking streaming text with respect to one or more lexicons. In a real operational environment it is likely that data would need to be processed separately for each lexicon or search technique. However, the searches would be so fast that multiple passes should not be considered as a limitation a priori. Indeed, it is conceivable that large databases could be searched as often as necessary if new queries were deemed worthwhile. This project is concerned with evaluating the Exegy Text Miner installed in the New Architectures Testbed running under software version 2.0. The concrete goals of the evaluation were to test the speed and accuracy of the Exegy and explore ways that it could be employed in current or future text-processing projects at Lawrence Livermore National Laboratory (LLNL). This study extended beyond this to evaluate its suitability for processing foreign language sources. The scope of this study was limited to the capabilities of the Exegy Text Miner in the file search mode and does not attempt simulating the streaming mode. Since the capabilities of the machine are invariant to the choice of input mode and since timing should not depend on this choice, it was felt that the added effort was not necessary for this restricted study.« less

Tree disease and wood decay as agents of environmental and social change

Treesearch

Kevin T. Smith

2018-01-01

The breakdown or decay of wood is a prominent process in landscape health and disease. The bulk of the energy captured and stored by natural woodlands, orchards, and agroforestry operations is allocated to produce wood. The release of that stored energy and the cycling of the constituent mineral elements into environmental pools and other organisms is through processes...

Optical-electronic system for express analysis of mineral raw materials dressability by color sorting method

NASA Astrophysics Data System (ADS)

Alekhin, Artem A.; Gorbunova, Elena V.; Chertov, Aleksandr N.; Petuhova, Darya B.

2013-04-01

Due to the depletion of solid minerals ore reserves and the involvement in the production of the poor and refractory ores a process of continuous appreciation of minerals is going. In present time at the market of enrichment equipment are well represented optical sorters of various firms. All these sorters are essentially different from each other by parameters of productivity, classes of particles sizes for processed raw, nuances of decision algorithm, as well as by color model (RGB, YUV, HSB, etc.) chosen to describe the color of separating mineral samples. At the same time there is no dressability estimation method for mineral raw materials without direct semi-industrial test on the existing type of optical sorter, as well as there is no equipment realizing mentioned dressability estimation method. It should also be note the lack of criteria for choosing of one or another manufacturer (or type) of optical sorter. A direct consequence of this situation is the "opacity" of the color sorting method and the rejection of its potential customers. The proposed solution of mentioned problems is to develop the dressability estimation method, and to create an optical-electronic system for express analysis of mineral raw materials dressability by color sorting method. This paper has the description of structure organization and operating principles of experimental model optical-electronic system for express analysis of mineral raw material. Also in this work are represented comparison results of the proposed optical-electronic system and the real color sorter.

Financial Responsibility Calculator to Accompany Proposed Requirements Under CERCLA Section 108(b) For Classes of Facilities in the Hardrock Mining Industry

EPA Pesticide Factsheets

This calculator will help stakeholders (owners and operators) of hardrock mines or mineral processing facilities calculate the amount of financial responsibility they should obtain under the proposed CERCLA 108b requirements

Recovery of PET from packaging plastics mixtures by wet shaking table.

PubMed

Carvalho, M T; Agante, E; Durão, F

2007-01-01

Recycling requires the separation of materials appearing in a mass of wastes of heterogeneous composition and characteristics, into single, almost pure, component/material flows. The separation of materials (e.g., some types of plastics) with similar physical properties (e.g., specific gravity) is often accomplished by human sorting. This is the case of the separation of packaging plastics in municipal solid wastes (MSW). The low cost of virgin plastics and low value of recycled plastics necessitate the utilization of low cost techniques and processes in the recycling of packaging plastics. An experimental study was conducted to evaluate the feasibility of production of a PET product, cleaned from PVC and PS, using a wet shaking table. The wet shaking table is an environmentally friendly process, widely used to separate minerals, which has low capital and operational costs. Some operational variables of the equipment, as well as different feed characteristics, were considered. The results show that the separation of these plastics is feasible although, similarly to the mineral field, in somewhat complex flow sheets.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

1995-12-05

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other mineral particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, Kazimierz; Ignasiak, Boleslaw; Pawlak, Wanda; Kulik, Conrad; Lebowitz, Howard E.

1995-01-01

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

1997-02-11

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, Kazimierz; Ignasiak, Boleslaw; Pawlak, Wanda; Kulik, Conrad; Lebowitz, Howard E.

1997-01-01

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

20 CFR 725.495 - Criteria for determining a responsible operator.

Code of Federal Regulations, 2010 CFR

2010-04-01

... any other potentially liable operator which may be deemed to have been the miner's most recent... the responsible operator if no more recent employer may be considered a potentially liable operator. (4) If the miner's most recent employment by an operator ended while the operator was authorized to...

Geometallurgy of ironsand from the Waikato North Head deposit, New Zealand

USGS Publications Warehouse

Mauk, Jeffrey L.; Cocker, Helen A; Rogers, Harold; Ogiliev, Jamie; Padya, Alex B

2016-01-01

The Waikato North Head deposit produces a magnetic mineral concentrate from Quaternary sands that formed in a coastal setting in the North Island of New Zealand. Detailed examination of the magnetic mineral fraction of the different stratigraphic horizons mined at Waikato North Head shows that the youngest units yield concentrates with significant concentrations of gangue minerals that are included as composite grains, inclusions in titanomagnetite, and as gangue grains with titanomagnetite inclusions. The most abundant gangue minerals in the magnetic fractions of all mined units are pyroxene and amphibole; feldspar, quartz, and biotite are less abundant. The magnetic minerals, which are predominantly titanomagnetite, are used as feed for the Iron Plant in New Zealand Steel’s Glenbrook Steel Mill. From time to time, excessive accretion formation impacts the operation of the rotary reduction kilns of the Iron Plant. Olivine group minerals are the most common silicate phase in these accretions, and we hypothesise that the silicon and magnesium in these minerals are derived from the gangue minerals that are included in the magnetic mineral concentrate from the ironsands. Although various remediation processes are possible, the simplest and most cost effective would appear to be ensuring adequate blending of material from different stratigraphic units, particularly when the youngest strata are being mined in the deposit.

The Zapot pegmatite mineral county

USGS Publications Warehouse

Foord, E.E.; Soregaroli, A.E.; Gordon, H.M.

1999-01-01

The Zapot pegmatite is currently being mined for mineral specimens (chiefly amazonite, topaz and smoky quartz in miarolitic cavities), for gemstones (topaz and smoky quartz) and for decorative rock (amazonite). The deposit is owned and operated by Harvey Gordon Minerals of Reno, Nevada, and is the only amazonite-topaz mining operation in the state. Thousands of specimens from this operation have reached the collector market.

30 CFR 582.29 - Reports and records.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE.... The report shall show for each calendar month the location of each mining and processing activity; the... determined from G&G surveys, bottom sampling, drill holes, trenching, dredging, or mining. All excavations...

30 CFR 582.29 - Reports and records.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE.... The report shall show for each calendar month the location of each mining and processing activity; the... determined from G&G surveys, bottom sampling, drill holes, trenching, dredging, or mining. All excavations...

30 CFR 582.29 - Reports and records.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE.... The report shall show for each calendar month the location of each mining and processing activity; the... determined from G&G surveys, bottom sampling, drill holes, trenching, dredging, or mining. All excavations...

20 CFR 725.495 - Criteria for determining a responsible operator.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Third, to any other potentially liable operator which may be deemed to have been the miner's most recent... the responsible operator if no more recent employer may be considered a potentially liable operator. (4) If the miner's most recent employment by an operator ended while the operator was authorized to...

20 CFR 725.495 - Criteria for determining a responsible operator.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Third, to any other potentially liable operator which may be deemed to have been the miner's most recent... the responsible operator if no more recent employer may be considered a potentially liable operator. (4) If the miner's most recent employment by an operator ended while the operator was authorized to...

20 CFR 725.495 - Criteria for determining a responsible operator.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Third, to any other potentially liable operator which may be deemed to have been the miner's most recent... the responsible operator if no more recent employer may be considered a potentially liable operator. (4) If the miner's most recent employment by an operator ended while the operator was authorized to...

20 CFR 725.495 - Criteria for determining a responsible operator.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Third, to any other potentially liable operator which may be deemed to have been the miner's most recent... the responsible operator if no more recent employer may be considered a potentially liable operator. (4) If the miner's most recent employment by an operator ended while the operator was authorized to...

Propham mineralization in aqueous medium by anodic oxidation using boron-doped diamond anode: influence of experimental parameters on degradation kinetics and mineralization efficiency.

PubMed

Ozcan, Ali; Sahin, Yücel; Koparal, A Savaş; Oturan, Mehmet A

2008-06-01

This study aims the removal of a carbamate herbicide, propham, from aqueous solution by direct electrochemical advanced oxidation process using a boron-doped diamond (BDD) anode. This electrode produces large quantities of hydroxyl radicals from oxidation of water, which leads to the oxidative degradation of propham up to its total mineralization. Effect of operational parameters such as current, temperature, pH and supporting electrolyte on the degradation and mineralization rate was studied. The applied current and temperature exert a prominent effect on the total organic carbon (TOC) removal rate of the solutions. The mineralization of propham can be performed at any pH value between 3 and 11 without any loss in oxidation efficiency. The propham decay and its overall mineralization reaction follows a pseudo-first-order kinetics. The apparent rate constant value of propham oxidation was determined as 4.8 x 10(-4)s(-1) at 100 mA and 35 degrees C in the presence of 50mM Na(2)SO(4) in acidic media (pH: 3). A general mineralization sequence was proposed considering the identified oxidation intermediates.

Characteristics and adaptability of iron- and sulfur-oxidizing microorganisms used for the recovery of metals from minerals and their concentrates

PubMed Central

Rawlings, Douglas E

2005-01-01

Microorganisms are used in large-scale heap or tank aeration processes for the commercial extraction of a variety of metals from their ores or concentrates. These include copper, cobalt, gold and, in the past, uranium. The metal solubilization processes are considered to be largely chemical with the microorganisms providing the chemicals and the space (exopolysaccharide layer) where the mineral dissolution reactions occur. Temperatures at which these processes are carried out can vary from ambient to 80°C and the types of organisms present depends to a large extent on the process temperature used. Irrespective of the operation temperature, biomining microbes have several characteristics in common. One shared characteristic is their ability to produce the ferric iron and sulfuric acid required to degrade the mineral and facilitate metal recovery. Other characteristics are their ability to grow autotrophically, their acid-tolerance and their inherent metal resistance or ability to acquire metal resistance. Although the microorganisms that drive the process have the above properties in common, biomining microbes usually occur in consortia in which cross-feeding may occur such that a combination of microbes including some with heterotrophic tendencies may contribute to the efficiency of the process. The remarkable adaptability of these organisms is assisted by several of the processes being continuous-flow systems that enable the continual selection of microorganisms that are more efficient at mineral degradation. Adaptability is also assisted by the processes being open and non-sterile thereby permitting new organisms to enter. This openness allows for the possibility of new genes that improve cell fitness to be selected from the horizontal gene pool. Characteristics that biomining microorganisms have in common and examples of their remarkable adaptability are described. PMID:15877814

Characteristics and adaptability of iron- and sulfur-oxidizing microorganisms used for the recovery of metals from minerals and their concentrates.

PubMed

Rawlings, Douglas E

2005-05-06

Microorganisms are used in large-scale heap or tank aeration processes for the commercial extraction of a variety of metals from their ores or concentrates. These include copper, cobalt, gold and, in the past, uranium. The metal solubilization processes are considered to be largely chemical with the microorganisms providing the chemicals and the space (exopolysaccharide layer) where the mineral dissolution reactions occur. Temperatures at which these processes are carried out can vary from ambient to 80 degrees C and the types of organisms present depends to a large extent on the process temperature used. Irrespective of the operation temperature, biomining microbes have several characteristics in common. One shared characteristic is their ability to produce the ferric iron and sulfuric acid required to degrade the mineral and facilitate metal recovery. Other characteristics are their ability to grow autotrophically, their acid-tolerance and their inherent metal resistance or ability to acquire metal resistance. Although the microorganisms that drive the process have the above properties in common, biomining microbes usually occur in consortia in which cross-feeding may occur such that a combination of microbes including some with heterotrophic tendencies may contribute to the efficiency of the process. The remarkable adaptability of these organisms is assisted by several of the processes being continuous-flow systems that enable the continual selection of microorganisms that are more efficient at mineral degradation. Adaptability is also assisted by the processes being open and non-sterile thereby permitting new organisms to enter. This openness allows for the possibility of new genes that improve cell fitness to be selected from the horizontal gene pool. Characteristics that biomining microorganisms have in common and examples of their remarkable adaptability are described.

A modified sulfate process to lunar oxygen

NASA Technical Reports Server (NTRS)

Sullivan, Thomas A.

1992-01-01

A modified sulfate process which produces oxygen from iron oxide-bearing minerals in lunar soil is under development. Reaction rates of ilmenite in varying strength sulfuric acid have been determined. Quantitative conversion of ilmenite to ferrous sulfate was observed over a range of temperatures and concentrations. Data has also been developed on the calcination of by-product sulfates. System engineering for overall operability and simplicity has begun, suggesting that a process separating the digestion and sulfate dissolution steps may offer an optimum process.

30 CFR 250.1601 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Definitions. 250.1601 Section 250.1601 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1601 Definitions. Terms used in this...

An open data mining framework for the analysis of medical images: application on obstructive nephropathy microscopy images.

PubMed

Doukas, Charalampos; Goudas, Theodosis; Fischer, Simon; Mierswa, Ingo; Chatziioannou, Aristotle; Maglogiannis, Ilias

2010-01-01

This paper presents an open image-mining framework that provides access to tools and methods for the characterization of medical images. Several image processing and feature extraction operators have been implemented and exposed through Web Services. Rapid-Miner, an open source data mining system has been utilized for applying classification operators and creating the essential processing workflows. The proposed framework has been applied for the detection of salient objects in Obstructive Nephropathy microscopy images. Initial classification results are quite promising demonstrating the feasibility of automated characterization of kidney biopsy images.

Verification of geomechanical integrity and prediction of long-term mineral trapping for the Ketzin CO2 storage pilot site

NASA Astrophysics Data System (ADS)

Kempka, Thomas; De Lucia, Marco; Kühn, Michael

2014-05-01

Static and dynamic numerical modelling generally accompany the entire CO2 storage site life cycle. Thereto, it is required to match the employed models with field observations on a regular basis in order to predict future site behaviour. We investigated the coupled processes at the Ketzin CO2 storage pilot site [1] using a model coupling concept focusing on the temporal relevance of processes involved (hydraulic, chemical and mechanical) at given time-scales (site operation, abandonment and long-term stabilization). For that purpose, long-term dynamic multi-phase flow simulations [2], [3] established the basis for all simulations discussed in the following. Hereby, pressure changes resulting in geomechanical effects are largest during site operation, whereas geochemical reactions are governed by slow kinetics resulting in a long-term stabilization. To account for mechanical integrity, which may be mainly affected during site operation, we incorporated a regional-scale coupled hydro-mechanical model. Our simulation results show maximum ground surface displacements of about 4 mm, whereas shear and tensile failure are not observed. Consequently, the CO2 storage operation at the Ketzin pilot site does not compromise reservoir, caprock and fault integrity. Chemical processes responsible for mineral trapping are expected to mainly occur during long-term stabilization at the Ketzin pilot site [4]. Hence, our previous assessment [3] was extended by integrating two long-term mineral trapping scenarios. Thereby, mineral trapping contributes to the trapping mechanisms with 11.7 % after 16,000 years of simulation in our conservative and with 30.9 % in our maximum reactivity scenarios. Dynamic flow simulations indicate that only 0.2 % of the CO2 injected (about 67,270 t CO2 in total) is in gaseous state, but structurally trapped after 16,000 years. Depending on the studied long-term scenario, CO2 dissolution is the dominating trapping mechanism with 68.9 % and 88.1 %, respectively. We verified the mechanical integrity of the storage system during site operation and predicted the trapping mechanisms for the Ketzin pilot site based on a time-dependent integration of relevant processes for a time period of 16,000 years. Supported by our coupled modelling results, we conclude that CO2 storage at the Ketzin site is safe and reliable on the pilot scale. References [1] Martens, S., Kempka, T., Liebscher, A., Lüth, S., Möller, F., Myrttinen, A., Norden, B., Schmidt-Hattenberger, C., Zimmer, M., Kühn, M. Europe's longest-operating on-shore CO2 storage site at Ketzin, Germany: a progress report after three years of injection. Environmental Earth Sciences 2012 67(2): 323-334. [2] Kempka, T., Kühn, M. Numerical simulations of CO2 arrival times and reservoir pressure coincide with observations from the Ketzin pilot site, Germany. Environmental Earth Sciences 2013 70(8): 3675-3685. [3] Kempka, T., Klein, E., De Lucia, M., Tillner, E., Kühn, M. Assessment of Long-term CO2 Trapping Mechanisms at the Ketzin Pilot Site (Germany) by Coupled Numerical Modelling. Energy Procedia 2013 37: 5419-5426. [4] Klein, E., De Lucia, M., Kempka, T., Kühn, M. Evaluation of long-term mineral trapping at the Ketzin pilot site for CO2 storage: An integrative approach using geochemical modelling and reservoir simulation. International Journal of Greenhouse Gas Control 2013 19: 720-730.

30 CFR 822.11 - Essential hydrologic functions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Essential hydrologic functions. 822.11 Section... IN ALLUVIAL VALLEY FLOORS § 822.11 Essential hydrologic functions. (a) The operator of a surface coal... throughout the mining and reclamation process the essential hydrologic functions of an alluvial valley floor...

30 CFR 582.5 - Disclosure of data and information to the public.

Code of Federal Regulations, 2012 CFR

2012-07-01

... public. 582.5 Section 582.5 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE... or more leases, to ensure proper Mining Plans for a common orebody, or to promote operational safety...), unitization agreement, or joint Mining Plan. (c) Geophysical data, processed geophysical information, and...

30 CFR 582.5 - Disclosure of data and information to the public.

Code of Federal Regulations, 2013 CFR

2013-07-01

... public. 582.5 Section 582.5 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE... or more leases, to ensure proper Mining Plans for a common orebody, or to promote operational safety...), unitization agreement, or joint Mining Plan. (c) Geophysical data, processed geophysical information, and...

30 CFR 582.5 - Disclosure of data and information to the public.

Code of Federal Regulations, 2014 CFR

2014-07-01

... public. 582.5 Section 582.5 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE... or more leases, to ensure proper Mining Plans for a common orebody, or to promote operational safety...), unitization agreement, or joint Mining Plan. (c) Geophysical data, processed geophysical information, and...

77 FR 16865 - Proposed Extension of Existing Information Collection; Occupational Noise Exposure

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

..., administrative controls, and personal protective equipment to protect miners from harmful levels of noise that..., compressors, conveyors, trucks, loaders, and other heavy-duty equipment for the excavation, haulage, and processing of material. This equipment creates high sound levels, exposing machine operators as well as...

43 CFR 3590.0-7 - Scope.

Code of Federal Regulations, 2013 CFR

2013-10-01

... hydrocarbon from tar sands or oil shale by in-situ methods utilizing boreholes or wells, part 3160 of this... regulations in this part govern operations for the discovery, testing, development, mining, reclamation, and processing of all minerals under lease, license or permit issued for Federal lands under the regulations in...

43 CFR 3590.0-7 - Scope.

Code of Federal Regulations, 2012 CFR

2012-10-01

... hydrocarbon from tar sands or oil shale by in-situ methods utilizing boreholes or wells, part 3160 of this... regulations in this part govern operations for the discovery, testing, development, mining, reclamation, and processing of all minerals under lease, license or permit issued for Federal lands under the regulations in...

43 CFR 3590.0-7 - Scope.

Code of Federal Regulations, 2014 CFR

2014-10-01

... hydrocarbon from tar sands or oil shale by in-situ methods utilizing boreholes or wells, part 3160 of this... regulations in this part govern operations for the discovery, testing, development, mining, reclamation, and processing of all minerals under lease, license or permit issued for Federal lands under the regulations in...

43 CFR 3590.0-7 - Scope.

Code of Federal Regulations, 2011 CFR

2011-10-01

... hydrocarbon from tar sands or oil shale by in-situ methods utilizing boreholes or wells, part 3160 of this... regulations in this part govern operations for the discovery, testing, development, mining, reclamation, and processing of all minerals under lease, license or permit issued for Federal lands under the regulations in...

36 CFR 292.67 - Operating plan approval-outstanding mineral rights.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Operating plan approval-outstanding mineral rights. 292.67 Section 292.67 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral...

36 CFR 292.66 - Operating plan requirements-outstanding mineral rights.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Operating plan requirements-outstanding mineral rights. 292.66 Section 292.66 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE NATIONAL RECREATION AREAS Smith River National Recreation Area Outstanding Mineral...

Dissipation of bentazone, pyrimethanil and boscalid in biochar and digestate based soil mixtures for biopurification systems.

PubMed

Mukherjee, Santanu; Tappe, Wolfgang; Weihermueller, Lutz; Hofmann, Diana; Köppchen, Stephan; Laabs, Volker; Schroeder, Tom; Vereecken, Harry; Burauel, Peter

2016-02-15

Biopurification systems, such as biofilters, are biotechnological tools to prevent point sources of pesticide pollution stemming from on-farm operations. For the purification processes pesticide sorption and mineralization and/or dissipation are essential and both largely depend on the type of filling materials and the pesticide in use. In this paper the mineralization and dissipation of three contrasting (14)C-labeled pesticides (bentazone, boscalid, and pyrimethanil) were investigated in laboratory incubation experiments using sandy soil, biochar produced from Pine woodchips, and/or digestate obtained from anaerobic digestion process using maize silage, chicken manure, beef and pig urine as feedstock. The results indicate that the addition of digestate increased pesticide mineralization, whereby the mineralization was not proportional to the digestate loads in the mixture, indicating a saturation effect in the turnover rate of pesticides. This effect was in correlation with the amount of water extractable DOC, obtained from the digestate based mixtures. Mixing biochar into the soil generally reduced total mineralization and led to larger sorption/sequestration of the pesticides, resulting in faster decrease of the extractable fraction. Also the addition of biochar to the soil/digestate mixtures reduced mineralization compared to the digestate alone mixture but mineralization rates were still higher as for the biochar/soil alone. In consequence, the addition of biochar to the soil generally decreased pesticide dissipation times and larger amounts of biochar led to high amounts of non-extractable residues of pesticide in the substrates. Among the mixtures tested, a mixture of digestate (5%) and biochar (5%) gave optimal results with respect to mineralization and simultaneous sorption for all three pesticides. Copyright © 2015 Elsevier B.V. All rights reserved.

Lunar material resources: An overview

NASA Technical Reports Server (NTRS)

Carter, James L.

1992-01-01

The analysis of returned lunar samples and a comparison of the physical and chemical processes operating on the Moon and on the Earth provide a basis for predicting both the possible types of material resources (especially minerals and rocks) and the physical characteristics of ore deposits potentially available on the Moon. The lack of free water on the Moon eliminates the classes of ore deposits that are most exploitable on Earth; namely, (1) hydrothermal, (2) secondary mobilization and enrichment, (3) precipitation from a body of water, and (4) placer. The types of lunar materials available for exploitation are whole rocks and their contained minerals, regolith, fumarolic and vapor deposits, and nonlunar materials, including solar wind implantations. Early exploitation of lunar material resources will be primarily the use of regolith materials for bulk shielding; the extraction from regolith fines of igneous minerals such as plagioclase feldspars and ilmenite for the production of oxygen, structural metals, and water; and possibly the separation from regolith fines of solar-wind-implanted volatiles. The only element, compound, or mineral, that by itself has been identified as having the economic potential for mining, processing, and return to Earth is helium-3.

Process for coal liquefaction in staged dissolvers

DOEpatents

Roberts, George W.; Givens, Edwin N.; Skinner, Ronald W.

1983-01-01

There is described an improved liquefaction process by which coal is converted to a low ash and low sulfur carbonaceous material that can be used as a fuel in an environmentally acceptable manner without costly gas scrubbing equipment. In the process, coal is slurried with a pasting oil, passed through a preheater and at least two dissolvers in series in the presence of hydrogen-rich gases at elevated temperatures and pressures. Solids, including mineral ash and unconverted coal macerals, are separated from the condensed reactor effluent. In accordance with the improved process, the first dissolver is operated at a higher temperature than the second dissolver. This temperature sequence produces improved product selectivity and permits the incorporation of sufficient hydrogen in the solvent for adequate recycle operations.

30 CFR 57.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Operator-carrying overhead cranes. 57.16014 Section 57.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 56.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Operator-carrying overhead cranes. 56.16014 Section 56.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 56.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operator-carrying overhead cranes. 56.16014 Section 56.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 57.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operator-carrying overhead cranes. 57.16014 Section 57.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2012 CFR

2012-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Withdrawal from operation of the mining...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2014 CFR

2014-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Withdrawal from operation of the mining...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2013 CFR

2013-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Withdrawal from operation of the mining...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2011 CFR

2011-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Withdrawal from operation of the mining...

30 CFR 250.1612 - Well-control drills.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Well-control drills. 250.1612 Section 250.1612 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1612 Well-control drills. Well-control...

30 CFR 250.511 - Traveling-block safety device.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Traveling-block safety device. 250.511 Section 250.511 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... after each drill-line slipping operation. The results of the operational check must be entered in the...

Dyes removal from textile wastewater using graphene based nanofiltration

NASA Astrophysics Data System (ADS)

Makertihartha, I. G. B. N.; Rizki, Z.; Zunita, M.; Dharmawijaya, P. T.

2017-05-01

Wastewater produced from textile industry is having more strict regulation. The major pollutant of wastewater from textile industry is Dyes. Dyes have several harsh properties i.e toxic, volatile, complexing easily with mineral ions that are dissolved in water (decreasing the amount of important mineral ions in water), and hard to disintegrate, therefore it must be removed from the waste stream. There are several methods and mechanisms to remove dyes such as chemical and physical sorption, evaporation, biological degradation, and photocatalytic system that can be applied to the waste stream. Membrane-based separation technology has been introduced in dyes removal treatment and is well known for its advantages (flexibility, mild operating condition, insensitive to toxic pollutant). Graphene and its derivatives are novel materials which have special properties due to its ultrathin layer and nanometer-size pores. Thus, the materials are very light yet strong. Moreover, it has low cost and easy to fabricate. Recently, the application of graphene and its derivatives in nanofiltration membrane processes is being widely explored. This review investigates the potentials of graphene based membrane in dyes removal processes. The operating conditions, dyes removal effectiveness, and the drawbacks of the process are the main focus in this paper.

Photonic efficiency of the photodegradation of paracetamol in water by the photo-Fenton process.

PubMed

Yamal-Turbay, E; Ortega, E; Conte, L O; Graells, M; Mansilla, H D; Alfano, O M; Pérez-Moya, M

2015-01-01

An experimental study of the homogeneous Fenton and photo-Fenton degradation of 4-amidophenol (paracetamol, PCT) is presented. For all the operation conditions evaluated, PCT degradation is efficiently attained by both Fenton and photo-Fenton processes. Also, photonic efficiencies of PCT degradation and mineralization are determined under different experimental conditions, characterizing the influence of hydrogen peroxide (H2O2) and Fe(II) on both contaminant degradation and sample mineralization. The maximum photonic degradation efficiencies for 5 and 10 mg L(-1) Fe(II) were 3.9 (H2O2 = 189 mg L(-1)) and 5 (H2O2 = 378 mg L(-1)), respectively. For higher concentrations of oxidant, H2O2 acts as a "scavenger" radical, competing in pollutant degradation and reducing the reaction rate. Moreover, in order to quantify the consumption of the oxidizing agent, the specific consumption of the hydrogen peroxide was also evaluated. For all operating conditions of both hydrogen peroxide and Fe(II) concentration, the consumption values obtained for Fenton process were always higher than the corresponding values observed for photo-Fenton. This implies a less efficient use of the oxidizing agent for dark conditions.

Impact of solvent extraction organics on bioleaching by Acidithiobacillus ferrooxidans

NASA Astrophysics Data System (ADS)

Yu, Hualong; Liu, Xiaorong; Shen, Junhui; Chi, Daojie

2017-03-01

Solvent extraction organics (SX organics) entrained and dissoluted in the raffinate during copper SX operation, can impact bioleaching in case of raffinate recycling. The influence of SX organics on bioleaching process by Acidithiobacillus ferrooxidans (At. ferrooxidans) has been investigated. The results showed that, cells of At. ferrooxidans grew slower with contaminated low-grade chalcopyrite ores in shaken flasks bioleaching, the copper bioleaching efficiency reached 15%, lower than that of 24% for uncontaminated minerals. Obviously, the SX organics could adsorb on mineral surface and hinder its contact with bacterials, finanlly lead to the low bioleaching efficiency.

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 910.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 910.795 Section 910.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE GEORGIA § 910.795 Small operator...

30 CFR 947.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 947.795 Section 947.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE WASHINGTON § 947.795 Small operator...

30 CFR 922.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 922.795 Section 922.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE MICHIGAN § 922.795 Small operator...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 250.424 - What are the requirements for prolonged drilling operations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... drilling operations? 250.424 Section 250.424 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Casing and Cementing Requirements § 250.424 What are the requirements for prolonged...

30 CFR 912.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 912.795 Section 912.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE IDAHO § 912.795 Small operator...

30 CFR 56.19057 - Hoist operator's physical fitness.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hoist operator's physical fitness. 56.19057 Section 56.19057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoisting Procedures § 56.19057 Hoist operator's physical fitness. No person shall operate a hoist...

30 CFR 57.19057 - Hoist operator's physical fitness.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hoist operator's physical fitness. 57.19057 Section 57.19057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoisting Procedures § 57.19057 Hoist operator's physical fitness. No person shall operate a hoist...

30 CFR 56.19057 - Hoist operator's physical fitness.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hoist operator's physical fitness. 56.19057 Section 56.19057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoisting Procedures § 56.19057 Hoist operator's physical fitness. No person shall operate a hoist...

30 CFR 57.19057 - Hoist operator's physical fitness.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hoist operator's physical fitness. 57.19057 Section 57.19057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoisting Procedures § 57.19057 Hoist operator's physical fitness. No person shall operate a hoist...

30 CFR 56.19057 - Hoist operator's physical fitness.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hoist operator's physical fitness. 56.19057 Section 56.19057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoisting Procedures § 56.19057 Hoist operator's physical fitness. No person shall operate a hoist...

30 CFR 57.19057 - Hoist operator's physical fitness.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hoist operator's physical fitness. 57.19057 Section 57.19057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoisting Procedures § 57.19057 Hoist operator's physical fitness. No person shall operate a hoist...

Sacrificial adsorbate for surfactants utilized in chemical floods of enhanced oil recovery operations

DOEpatents

Johnson, Jr., James S.; Westmoreland, Clyde G.

1982-01-01

The present invention is directed to a sacrificial or competitive adsorbate for surfactants contained in chemical flooding emulsions for enhanced oil recovery operations. The adsorbate to be utilized in the method of the present invention is a caustic effluent from the bleach stage or the weak black liquor from the digesters and pulp washers of the kraft pulping process. This effluent or weak black liquor is injected into an oil-bearing subterranean earth formation prior to or concurrent with the chemical flood emulsion and is adsorbed on the active mineral surfaces of the formation matrix so as to effectively reduce adsorption of surfactant in the chemical flood. Alternatively, the effluent or liquor can be injected into the subterranean earth formation subsequent to a chemical flood to displace the surfactant from the mineral surfaces for the recovery thereof.

Sacrificial adsorbate for surfactants utilized in chemical floods of enhanced oil recovery operations

DOEpatents

Johnson, J.S. Jr.; Westmoreland, C.G.

1980-08-20

The present invention is directed to a sacrificial or competitive adsorbate for surfactants contained in chemical flooding emulsions for enhanced oil recovery operations. The adsorbate to be utilized in the method of the present invention is a caustic effluent from the bleach stage or the weak black liquor from the digesters and pulp washers of the kraft pulping process. This effluent or weak black liquor is injected into an oil-bearing subterranean earth formation prior to or concurrent with the chemical flood emulsion and is adsorbed on the active mineral surfaces of the formation matrix so as to effectively reduce adsorption of surfactant in the chemical flood. Alternatively, the effluent or liquor can be injected into the subterranean earth formation subsequent to a chemical flood to displace the surfactant from the mineral surfaces for the recovery thereof.

Formation of secondary minerals in a lysimeter approach - A mineral-microbe interaction

NASA Astrophysics Data System (ADS)

Schäffner, F.; Merten, D.; De Giudici, G.; Beyer, A.; Akob, D. M.; Ricci, P. C.; Küsel, K.; Büchel, G.

2012-04-01

Heavy metal contamination of large areas due to uranium mining operations poses a serious long-term environmental problem. In the Ronneburg district (eastern Thuringia, Germany), leaching of low grade uranium bearing ores (uranium content < 300 g/t) occurred from 1972 to 1990 using acid mine drainage (AMD; pH 2.7-2.8) and diluted sulphuric acid (10 g/l). Secondary mineral phases like birnessite, todorokite and goethite occur within a natural attenuation process associated with enrichment of heavy metals, especially Cd, Ni, Co, Cu and Zn due to a residual contamination even after remediation efforts. To reveal the processes of secondary mineral precipitation in the field a laboratory lysimeter approach was set up under in situ-like conditions. Homogenized soil from the field site and pure quartz sand were used as substrates. In general, in situ measurements of redox potentials in the substrates showed highly oxidizing conditions (200-750 mV). Water was supplied to the lysimeter from below via a mariottés bottle containing contaminated groundwater from the field. Evaporation processes were allowed, providing a continuous flow of water. This led to precipitation of epsomite and probably aplowite on the top layer of substrate, similar to what is observed in field investigations. After 4 weeks, the first iron and manganese bearing secondary minerals became visible. Soil water samples were used to monitor the behaviour of metals within the lysimeter. Saturation indices (SI) for different secondary minerals were calculated with PHREEQC. The SI of goethite showed oversaturation with respect to the soil solution. SEM-EDX analyses and IR spectroscopy confirmed the formation of goethite. Geochemical data revealed that goethite formation was mainly dominated by Eh/pH processes and that heavy metals, e.g. Zn and U, could be enriched in this phase. Although Eh/pH data does not support formation of manganese minerals, Mn(II)-oxidizing bacteria (MOB) could be isolated from field soil samples, supporting the fact that microorganisms may influence this natural attenuation process. Laser ablation ICP-MS data reveal accumulation of manganese in MOB biomass on Mn(II)-containing agar plates. Furthermore, it was possible to show the importance of iron on this process, as some MOB isolates were able to oxidize manganese independently from the iron content, whereas some are not. The latter isolates are only able to oxidize manganese if iron is present in the media. In the lysimeter, SEM-EDX data showed microorganisms in organic rich phases together with the occurrence of manganese, oxygen, and nickel, indicating manganese oxides enriched in nickel. Although this new mineral phases could not yet be identified microprobe EDX results from polished thin sections showed needle-like mineral structures that are similar to the birnessite and todorokite samples observed from field samples. Hence, the lysimeter experiment revealed that the formation of iron and manganese minerals that are involved in heavy metal natural attenuation is result of both abiotic and biotic processes.

30 CFR 250.131 - Will MMS notify me before conducting an inspection?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Will MMS notify me before conducting an inspection? 250.131 Section 250.131 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF General Inspection of Operations...

76 FR 54782 - Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-02

... Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer..., Interior. ACTION: Notice of the Availability of Environmental Documents Prepared for OCS Mineral Proposals by the Gulf of Mexico OCS Region. SUMMARY: The Bureau of Ocean Energy Management, Regulation and...

75 FR 67994 - Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-04

... Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer..., Interior. ACTION: Notice of the availability of environmental documents prepared for OCS mineral proposals by the Gulf of Mexico OCS Region. SUMMARY: The Bureau of Ocean Energy Management, Regulation and...

75 FR 67996 - Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-04

... Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer... regarding whether those effects have significant impacts. Environmental Assessments are used to evaluate.... ACTION: Notice of the Availability of Environmental Documents Prepared for OCS Mineral Proposals by the...

76 FR 16632 - Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-24

... Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...: Notice of the Availability of Environmental Documents Prepared for OCS Mineral Proposals by the Gulf of Mexico OCS Region. SUMMARY: The Bureau of Ocean Energy Management, Regulation and Enforcement (BOEMRE...

76 FR 38673 - Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-01

... Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer..., Interior. ACTION: Notice of the availability of environmental documents prepared for OCS mineral proposals by the Gulf of Mexico OCS Region. SUMMARY: The Bureau of Ocean Energy Management, Regulation and...

30 CFR 250.136 - How will MMS determine if my operating performance is unacceptable?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will MMS determine if my operating performance is unacceptable? 250.136 Section 250.136 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT...) Accidents and their nature; (b) Pollution events, environmental damages and their nature; (c) Incidents of...

30 CFR 250.256 - What related facilities and operations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What related facilities and operations information must accompany the DPP or DOCD? 250.256 Section 250.256 Mineral Resources MINERALS MANAGEMENT... SHELF Plans and Information Contents of Development and Production Plans (dpp) and Development...

The 'Risk' of Implementing New Regulations on Game-Changing Technology: Sequestering CO2 in the Built Environment.

NASA Astrophysics Data System (ADS)

Constantz, B.

2009-05-01

Calera's Carbon Capture and Conversion (CCC) technology with beneficial reuse has been called, "game- changing" by Carl Pope, Director of the Sierra Club. Calera offers a solution to the scale of the carbon problem. By capturing carbon into the built environment, Calera provides a sound and cost-effective alternative to Geologic Sequestration and Terrestrial Sequestration. By chemically bonding carbon dioxide into carbonate minerals, this CCC technology permanently converts CO2 into a mineral form which can be stored above- ground, on the floor of the ocean, or used as a building material. The process produces a suite of carbonate containing minerals of various polymorphic forms and crystallographic characteristics, which can be substituted into blends with portland cements to produce concretes with reduced carbon, carbon neutral, and negative carbon footprints. For each ton of product produced, approximately half a ton of carbon dioxide is sequestered using the Calera process. A number of different technologies have been proposed for trapping CO2 into a permanent mineral form. One such process utilizes flue gas from power plants, cement plants, foundries, etc. as a feedstock for production of carbonate mineral forms which can be used as cements and aggregates for making concrete. The carbonate materials produced are essentially forms of limestone, which have morphologies which allow them to glue themselves together when mixed with water, just as conventional portland cement does. The result is a cemented limestone product, which has the permanent structure and stability of the limestone, which forms 10% of the earth's crust. A significant advantage of this process is that it does not require the separation of CO2 from the flue gas, a highly cost and energy intensive step. By producing a usable product, CCC also provides an economical solution to global warming. While the cost of this process may, in some cases, exceed the selling price of the resultant materials, the value produced combined with available carbon credits makes this CCC technology economically and environmentally sustainable. Calera has a pilot plant and laboratory operating at Moss Landing, CA, within the Monterey Bay Marine Sanctuary. During operation, the Calera process draws in seawater, which is combined with a variety of natural and manufactured minerals held in liquid suspension. Flue gas from the neighboring power plant is then sparged through the liquid. The process may also be enhanced by supplementing the water with additional minerals. These minerals are then separated from the seawater and are further processed to produce cement or other building materials. After the seawater flows through the Calera process, additional flue gas is sparged through the water to restore the native bicarbonate buffer levels and pH to match the pH of the incoming seawater, and within the prescribed limits. The outflow will be largely unchanged, with the exception of being calcium and magnesium depleted. One of the biggest hurdles Calera faces today is gaining support for this new technology. Most of the state and federal regulatory agencies are very familiar with geologic sequestration, and consequently most of the legislative language is geared towards supporting this form of carbon capture. For example, when a Request for Proposal comes out from the Department of Energy it often limits applicants to some form of geologic sequestration activity. This scenario is true for grant funding, loans and tax credits. Calera is spending a considerable amount of time and effort to open these opportunities up to all forms of carbon capture. An overview of the process along with the risk involved in changing regulations will be presented.

40 CFR 436.242 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... from that impoundment. The height difference between the maximum safe surge capacity level and the normal operating level must be greater than the inches of rain representing the 10-year, 24-hour rainfall...

40 CFR 436.232 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... from that impoundment. The height difference between the maximum safe surge capacity level and the normal operating level must be greater than the inches of rain representing the 10-year, 24-hour rainfall...

40 CFR 436.62 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... from that impoundment. The height difference between the maximum safe surge capacity level and the normal operating level must be greater than the inches of rain representing the 10-year, 24-hour rainfall...

40 CFR 436.192 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... discharged from that impoundment. The height difference between the maximum safe surge capacity level and the normal operating level must be greater than the inches of rain representing the 10-year, 24-hour rainfall...

40 CFR 436.252 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... from that impoundment. The height difference between the maximum safe surge capacity level and the normal operating level must be greater than the inches of rain representing the 10-year, 24-hour rainfall...

40 CFR 436.262 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY... from that impoundment. The height difference between the maximum safe surge capacity level and the normal operating level must be greater than the inches of rain representing the 10-year, 24-hour rainfall...

75 FR 65034 - Petition for Modification of Existing Mandatory Safety Standard

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-21

... application, processing, and disposition of petitions for modification. This notice is a summary of a petition for modification filed by the party listed below to modify the application of an existing mandatory... operator or representative of miners to file a petition to modify the application of any mandatory safety...

40 CFR 60.675 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Test methods and procedures. 60.675... Mineral Processing Plants § 60.675 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in...

30 CFR 282.5 - Disclosure of data and information to the public.

Code of Federal Regulations, 2011 CFR

2011-07-01

... public. 282.5 Section 282.5 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND... unitization of operations on two or more leases, to ensure proper Mining Plans for a common orebody, or to... the affected lease(s), unitization agreement, or joint Mining Plan. (c) Geophysical data, processed...

30 CFR 580.41 - What types of geological data and information must I submit to BOEM?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (including geochemical) data and information describing each operation of analysis, processing, and... 30 Mineral Resources 2 2014-07-01 2014-07-01 false What types of geological data and information... CONTINENTAL SHELF Data Requirements Geological Data and Information § 580.41 What types of geological data and...

30 CFR 580.41 - What types of geological data and information must I submit to BOEM?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (including geochemical) data and information describing each operation of analysis, processing, and... 30 Mineral Resources 2 2013-07-01 2013-07-01 false What types of geological data and information... CONTINENTAL SHELF Data Requirements Geological Data and Information § 580.41 What types of geological data and...

The fate of cyanide in leach wastes at gold mines: an environmental perspective

USGS Publications Warehouse

Johnson, Craig A.

2015-01-01

Cyanide-containing and cyanide-related species are subject to attenuation mechanisms that lead to dispersal to the atmosphere, chemical transformation to other carbon and nitrogen species, or sequestration as cyanometallic precipitates or adsorbed species on mineral surfaces. Dispersal to the atmosphere and chemical transformation amount to permanent elimination of cyanide, whereas sequestration amounts to storage of cyanide in locations from which it can potentially be remobilized by infiltrating waters if conditions change. From an environmental perspective, the most significant cyanide releases from gold leach operations involve catastrophic spills of process solutions or leakage of effluent to the unsaturated or saturated zones. These release pathways are unfavorable for two important cyanide attenuation mechanisms that tend to occur naturally: dispersal of free cyanide to the atmosphere and sunlight-catalyzed dissociation of strong cyanometallic complexes, which produces free cyanide that can then disperse to the atmosphere. The widest margins of environmental safety will be achieved where mineral processing operations are designed so that time for offgassing, aeration, and sunlight exposure are maximized in the event that cyanide-bearing solutions are released inadvertently.

30 CFR 250.408 - May I use alternative procedures or equipment during drilling operations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... during drilling operations? 250.408 Section 250.408 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.408 May I use alternative procedures or equipment...

30 CFR 250.1602 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1602 Applicability. (a) The requirements of this subpart P are applicable to all exploration, development, and production operations under an...

Application of fuzzy AHP method to IOCG prospectivity mapping: A case study in Taherabad prospecting area, eastern Iran

NASA Astrophysics Data System (ADS)

Najafi, Ali; Karimpour, Mohammad Hassan; Ghaderi, Majid

2014-12-01

Using fuzzy analytical hierarchy process (AHP) technique, we propose a method for mineral prospectivity mapping (MPM) which is commonly used for exploration of mineral deposits. The fuzzy AHP is a popular technique which has been applied for multi-criteria decision-making (MCDM) problems. In this paper we used fuzzy AHP and geospatial information system (GIS) to generate prospectivity model for Iron Oxide Copper-Gold (IOCG) mineralization on the basis of its conceptual model and geo-evidence layers derived from geological, geochemical, and geophysical data in Taherabad area, eastern Iran. The FuzzyAHP was used to determine the weights belonging to each criterion. Three geoscientists knowledge on exploration of IOCG-type mineralization have been applied to assign weights to evidence layers in fuzzy AHP MPM approach. After assigning normalized weights to all evidential layers, fuzzy operator was applied to integrate weighted evidence layers. Finally for evaluating the ability of the applied approach to delineate reliable target areas, locations of known mineral deposits in the study area were used. The results demonstrate the acceptable outcomes for IOCG exploration.

30 CFR 57.5070 - Miner training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Miner training. 57.5070 Section 57.5070 Mineral... Agents, and Diesel Particulate Matter Diesel Particulate Matter-Underground Only § 57.5070 Miner training. (a) Mine operators must provide annual training to all miners at a mine covered by this part who can...

Carbon Mineralization by Aqueous Precipitation for Beneficial Use of CO 2 from Flue Gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Devenney, Martin; Gilliam, Ryan; Seeker, Randy

The objective of this project was to demonstrate an innovative process to mineralize CO 2 from flue gas directly to reactive carbonates and maximize the value and versatility of its beneficial use products. The program scope includes the design, construction, and testing of a CO 2 Conversion to Material Products (CCMP) Pilot Demonstration Plant utilizing CO 2 from the flue gas of a power production facility in Moss Landing, CA as well as flue gas from coal combustion. This final report details all development, analysis, design and testing of the project. Also included in the final report are an updatedmore » Techno-Economic Analysis and CO 2 Lifecycle Analysis. The subsystems included in the pilot demonstration plant are the mineralization subsystem, the Alkalinity Based on Low Energy (ABLE) subsystem, the waste calcium oxide processing subsystem, and the fiber cement board production subsystem. The fully integrated plant was proven to be capable of capturing CO 2 from various sources (gas and coal) and mineralizing it into a reactive calcium carbonate binder and subsequently producing commercial size (4ftx8ft) fiber cement boards. The final report provides a description of the “as built” design of these subsystems and the results of the commissioning activities that have taken place to confirm operability. The report also discusses the results of the fully integrated operation of the facility. Fiber cement boards have been produced in this facility exclusively using reactive calcium carbonate from captured CO 2 from flue gas. These boards meet all US and China appropriate acceptance standards. Use demonstrations for these boards are now underway.« less

78 FR 72096 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-02

... environmental documents prepared for OCS mineral proposals by the Gulf of Mexico OCS Region. SUMMARY: BOEM, in... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management [MMAA104000] Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region...

78 FR 47746 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... Environmental Documents Prepared for OCS Mineral Proposals by the Gulf of Mexico OCS Region. SUMMARY: BOEM, in... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management [MMAA104000] Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region...

78 FR 27422 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-10

... Environmental Documents Prepared for OCS Mineral Proposals by the Gulf of Mexico OCS Region. SUMMARY: BOEM, in... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management MMAA104000 Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region...

30 CFR 250.400 - Who is subject to the requirements of this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Who is subject to the requirements of this subpart? 250.400 Section 250.400 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations...

30 CFR 750.13 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 750.13 Section 750.13 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS...

30 CFR 250.130 - Why does MMS conduct inspections?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 250.130 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF General Inspection of Operations § 250.130... or other downhole operations. These include facilities under jurisdiction of other Federal agencies...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

Problem of the thermodynamic status of the mixed-layer minerals

USGS Publications Warehouse

Zen, E.-A.

1962-01-01

Minerals that show mixed layering, particularly with the component layers in random sequence, pose problems because they may behave thermodynamically as single phases or as polyphase aggregates. Two operational criteria are proposed for their distinction. The first scheme requires two samples of mixed-layer material which differ only in the proportions of the layers. If each of these two samples are allowed to equilibrate with the same suitably chosen monitoring solution, then the intensive parameters of the solution will be invariant if the mixed-layer sample is a polyphase aggregate, but not otherwise. The second scheme makes use of the fact that portions of many titration curves of clay minerals show constancy of the chemical activities of the components in the equilibrating solutions, suggesting phase separation. If such phase separation occurs for a mixed-layer material, then, knowing the number of independent components in the system, it should be possible to decide on the number of phases the mixed-layer material represents. Knowledge of the phase status of mixed-layer material is essential to the study of the equilibrium relations of mineral assemblages involving such material, because a given mixed-layer mineral will be plotted and treated differently on a phase diagram, depending on whether it is a single phase or a polyphase aggregate. Extension of the titration technique to minerals other than the mixed-layer type is possible. In particular, this method may be used to determine if cryptoperthites and peristerites are polyphase aggregates. In general, for any high-order phase separation, the method may be used to decide just at what point in this continuous process the system must be regarded operationally as a polyphase aggregate. ?? 1962.

Ranger's Legacy

NASA Technical Reports Server (NTRS)

1987-01-01

With its Landsat satellites, development of sensors, and advancement of processing techniques, NASA provided the initial technology base for another Earth-benefit application of image processing, Earth resources survey by means of remote sensing. Since each object has its own unique "signature," it is possible to distinguish among surface features and to generate computer-processed imagery identifying specific features of importance to resource managers. This capability, commercialized by Perceptive Scientific Instruments, Inc., offers practical application in such areas as agricultural crop forecasting, rangeland and forest management, land use planning, mineral and petroleum exploration, map making, water quality evaluation and disaster assessment. Major users of the technology have been federal, state, and local governments, but it is making its way into commercial operations, for example, resource exploration companies looking for oil, gas and mineral sources, and timber production firms seeking more efficient treeland management. Supporting both government and private users is a small industry composed of companies producing the processing hardware software. As is the case in the medical application, many of these companies are direct offspring of NASA's work.

Decolorization of brilliant green dye using immersed lamp sonophotocatalytic reactor

NASA Astrophysics Data System (ADS)

Gole, Vitthal L.; Priya, Astha; Danao, Sanjay P.

2017-12-01

The textile and dye industries require an enormous amount of water for processing and produce a large volume of wastewater. Generated wastewater had potential hazards and a threat to the aquatic biota. The present work investigates the decolorization of brilliant green dye using a combination of two advanced oxidation techniques viz sonocatalysis and photocatalysis (immersed lamp) known as sonophotocatalysis (3 L capacity). The efficiency of decolorization is further improved in the presence of various additives viz. copper oxide, zinc oxide, and sodium chloride. The maximum decolorization of brilliant green (BG) (94.8% in 120 min) obtained in the presence of zinc oxide. The total organic carbon of the treated samples was measured to monitor complete mineralization of BG. The sonophotocatalytic process (in the presence of zinc oxide) shows maximum mineralization. Synergic combination of two oxidation processes increased the production of oxidizing radicals. Continuous cleaning of catalyst surface (due to sonolysis effect) improves the activity of the catalyst for photolysis operation. The present work is highly useful for the development of a sonophotocatalytic process.

50 CFR 29.32 - Mineral rights reserved and excepted.

Code of Federal Regulations, 2013 CFR

2013-10-01

... practicable, conduct all exploration, development, and production operations in such a manner as to prevent... to the minimum space compatible with the conduct of efficient mineral operations. Persons conducting...

50 CFR 29.32 - Mineral rights reserved and excepted.

Code of Federal Regulations, 2010 CFR

2010-10-01

... practicable, conduct all exploration, development, and production operations in such a manner as to prevent... to the minimum space compatible with the conduct of efficient mineral operations. Persons conducting...

50 CFR 29.32 - Mineral rights reserved and excepted.

Code of Federal Regulations, 2014 CFR

2014-10-01

... practicable, conduct all exploration, development, and production operations in such a manner as to prevent... to the minimum space compatible with the conduct of efficient mineral operations. Persons conducting...

50 CFR 29.32 - Mineral rights reserved and excepted.

Code of Federal Regulations, 2011 CFR

2011-10-01

... practicable, conduct all exploration, development, and production operations in such a manner as to prevent... to the minimum space compatible with the conduct of efficient mineral operations. Persons conducting...

50 CFR 29.32 - Mineral rights reserved and excepted.

Code of Federal Regulations, 2012 CFR

2012-10-01

... practicable, conduct all exploration, development, and production operations in such a manner as to prevent... to the minimum space compatible with the conduct of efficient mineral operations. Persons conducting...

The mineralogy of bauxite for producing smelter-grade alumina

NASA Astrophysics Data System (ADS)

Authier-Martin, M.; Forte, G.; Ostap, S.; See, J.

2001-12-01

Aluminum-producing companies rely on low-cost, high-purity, smelter-grade alumina (aluminum oxide), and alumina production utilizes the bulk of bauxites mined world-wide. The mineralogy of the bauxites has a significant impact on the operation of the Bayer process for alumina production. Typically, the Bayer process produces smelter-grade alumina of 99.5% Al2O3, starting from bauxite containing 30% to 60% Al2O3. The main objective of the Bayer process is to extract the maximum amount of aluminum from the bauxite at as high an aluminate concentration in solution as possible, while limiting any troublesome side reactions. Only with a better understanding of the chemistry of the mineral species and a strict control of the operating/processing conditions can the Bayer process produce efficiently, a low cost, high-quality alumina with minimum detrimental environmental impact.

30 CFR 921.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 921.795 Section 921.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE MASSACHUSETTS § 921.795 Small...

30 CFR 57.15014 - Eye protection when operating grinding wheels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Eye protection when operating grinding wheels. 57.15014 Section 57.15014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... NONMETAL MINES Personal Protection Surface and Underground § 57.15014 Eye protection when operating...

30 CFR 57.15014 - Eye protection when operating grinding wheels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Eye protection when operating grinding wheels. 57.15014 Section 57.15014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... NONMETAL MINES Personal Protection Surface and Underground § 57.15014 Eye protection when operating...

77 FR 9961 - Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-21

... accordance with the provisions of 36 CFR 9.17, Randy Elliott has filed a proposed plan of operations to conduct mining operations on lands embracing Mineral Survey No. 923, patented mineral property within Wrangell-St. Elias National Park and Preserve. Public Availability: This plan of operations is available...

Teleoperated control system for underground room and pillar mining

DOEpatents

Mayercheck, William D.; Kwitowski, August J.; Brautigam, Albert L.; Mueller, Brian K.

1992-01-01

A teleoperated mining system is provided for remotely controlling the various machines involved with thin seam mining. A thin seam continuous miner located at a mining face includes a camera mounted thereon and a slave computer for controlling the miner and the camera. A plurality of sensors for relaying information about the miner and the face to the slave computer. A slave computer controlled ventilation sub-system which removes combustible material from the mining face. A haulage sub-system removes material mined by the continuous miner from the mining face to a collection site and is also controlled by the slave computer. A base station, which controls the supply of power and water to the continuous miner, haulage system, and ventilation systems, includes cable/hose handling module for winding or unwinding cables/hoses connected to the miner, an operator control module, and a hydraulic power and air compressor module for supplying air to the miner. An operator controlled host computer housed in the operator control module is connected to the slave computer via a two wire communications line.

System approach to automation and robotization of drivage

NASA Astrophysics Data System (ADS)

Zinov’ev, VV; Mayorov, AE; Starodubov, AN; Nikolaev, PI

2018-03-01

The authors consider the system approach to finding ways of no-man drilling and blasting in the face area by means of automation and robotization of operations with a view to reducing injuries in mines. The analysis is carried out in terms of the drilling and blasting technology applied in Makarevskoe Coal Field, Kuznetsk Coal Basin. Within the system-functional approach and using INDEFO procedure, the processes of drilling and blasthole charging are decomposed into related elementary operations. The automation and robotization methods to avoid the presence of miners in the face are found for each operation.

30 CFR 250.519 - How often do I have to monitor for casing pressure?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How often do I have to monitor for casing pressure? 250.519 Section 250.519 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations Casing Pressure Management §...

Electro activation of persulfate using iron sheet as low-cost electrode: the role of the operating conditions.

PubMed

Silveira, Jefferson E; Cardoso, Tais O; Barreto-Rodrigues, Marcio; Zazo, Juan A; Casas, José A

2018-05-01

This work assesses the role of the operational conditions upon the electro-activation of persulfate (PS) using sacrificed iron electrode as a continuous low-cost Fe 2+ source. An aqueous phenol solution (100 mg L -1 ) was selected as model effluent. The studied variables include current density (1-10 mA cm -2 ), persulfate concentration (0.7-2.85 g L -1 ), temperature (30-90°C) and the solution conductivity (2.7-20.7 mS cm -1 ) using Na 2 SO 4 and NaCl as supporting electrolyte. A mineralization degree of around 80% with Na 2 SO 4 and 92% in presence of NaCl was achieved at 30°C using 2.15 g L -1 PS at the lowest current density tested (1 mA cm -2 ). Besides PS concentration, temperature was the main variable affecting the process. In the range of 30-70°C, it showed a positive effect, achieving TOC conversion above 95% (using Na 2 SO 4 under the previous conditions) along with a significant increase in iron sludge, which adversely affects the economy of the process. A lumped and simplified kinetic model based on persulfate consumption and TOC mineralization is suggested. The activation energy obtained for the TOC decay was 29 kJ mol -1 . An estimated operating cost of US$ 3.00 per m 3 was obtained, demonstrating the economic feasibility of this process.

Potential Aquifer Vulnerability in Regions Down-Gradient from ...

EPA Pesticide Factsheets

Sandstone-hosted roll-front uranium ore deposits originate when U(VI) dissolved in groundwater is reduced and precipitated as insoluble U(IV) minerals. Groundwater redox geochemistry, aqueous complexation, and solute migration are instrumental in leaching uranium from source rocks and transporting it in low concentrations to a chemical redox interface where it is deposited in an ore zone typically containing the uranium minerals uraninite, pitchblende, and/or coffinite; various iron sulfides; native selenium; clays; and calcite. In situ recovery (ISR) of these uranium ores is a process of contacting the uranium mineral deposit with leaching (lixiviant) fluids via injection of the lixiviant into wells drilled into the subsurface aquifer that hosts uranium ore, while other extraction wells pump the dissolved uranium after dissolution of the uranium minerals. Environmental concerns during and after ISR include water quality impacts from: 1) potential excursions of leaching solutions away from the injection zone into down-dip, underlying, or overlying aquifers; 2) potential migration of uranium and its decay products (e.g., Ra, Rn, Pb); and, 3) potential migration of redox-sensitive trace metals (e.g., Fe, Mn, Mo, Se, V), metalloids (e.g., As), and anions (e.g., sulfate). This review describes the geochemical processes that control roll-front uranium transport and fate in groundwater systems, identifies potential aquifer vulnerabilities to ISR operations, identifies

30 CFR 582.27 - Conduct of operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Conduct of operations. 582.27 Section 582.27 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE... is necessary to be conducted prior to submission of a Mining Plan shall be in accordance with an...

30 CFR 582.27 - Conduct of operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Conduct of operations. 582.27 Section 582.27 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE... is necessary to be conducted prior to submission of a Mining Plan shall be in accordance with an...

30 CFR 582.27 - Conduct of operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Conduct of operations. 582.27 Section 582.27 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE... is necessary to be conducted prior to submission of a Mining Plan shall be in accordance with an...

30 CFR 933.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 933.795 Section 933.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NORTH CAROLINA § 933.795 Small...

30 CFR 942.795 - Small operator assistance program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance program. 942.795 Section 942.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE TENNESSEE § 942.795 Small...

30 CFR 903.795 - Small operator assistance program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance program. 903.795 Section 903.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE ARIZONA § 903.795 Small...

30 CFR 941.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 941.795 Section 941.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE SOUTH DAKOTA § 941.795 Small...

30 CFR 939.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 939.795 Section 939.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE RHODE ISLAND § 939.795 Small...

30 CFR 905.795 - Small operator assistance program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance program. 905.795 Section 905.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE CALIFORNIA § 905.795 Small...

30 CFR 90.205 - Approved sampling devices; operation; air flowrate.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approved sampling devices; operation; air... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-COAL MINERS WHO HAVE EVIDENCE OF THE DEVELOPMENT OF PNEUMOCONIOSIS Sampling Procedures § 90.205 Approved sampling devices; operation; air flowrate...

30 CFR 56.15014 - Eye protection when operating grinding wheels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Eye protection when operating grinding wheels. 56.15014 Section 56.15014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... MINES Personal Protection § 56.15014 Eye protection when operating grinding wheels. Face shields or...

30 CFR 56.15014 - Eye protection when operating grinding wheels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Eye protection when operating grinding wheels. 56.15014 Section 56.15014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... MINES Personal Protection § 56.15014 Eye protection when operating grinding wheels. Face shields or...

30 CFR 250.132 - What must I do when MMS conducts an inspection?

Code of Federal Regulations, 2010 CFR

2010-07-01

...? 250.132 Section 250.132 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF General Inspection of Operations... refueling facilities for any helicopters we use to regulate offshore operations. (b) You must make the...

30 CFR 1206.120 - How are operating allowances determined?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false How are operating allowances determined? 1206.120 Section 1206.120 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.120 How are operating allowances determined...

30 CFR 1206.120 - How are operating allowances determined?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false How are operating allowances determined? 1206.120 Section 1206.120 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.120 How are operating allowances determined...

30 CFR 1206.120 - How are operating allowances determined?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false How are operating allowances determined? 1206.120 Section 1206.120 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.120 How are operating allowances determined...

Implementation plan for Bolivian Mineral Exploration Fund

USGS Publications Warehouse

Kirkemo, Harold

1978-01-01

Bolivia ranks second among world producers of tin and antimony, and first in bismuth production. Mineral exports in 1975 were valued at $314.2 million, nearly 60 percent of the value of all exports, and petroleum product exports totalled nearly $157 million, or 30 percent of the total. Tin accounted for 58 percent of the total value of metallic mineral exports. The central government derived about 19 percent of its total tax revenues in 1975 from the mining sector. The mining sector consists of the large, medium, and small mining subsectors, a classification established by the government. Individual operations are referred to as large, medium, or small depending upon the subsector into which they are classified. All large mining enterprises are owned and operated by a government corporation, COMIBOL; the medium and small operations are privately owned. COMIBOL's exports in 1975 were valued at $171.8 million or 70 percent of the total mineral exports; the medium mines accounted for $55.5 million or 23 percent, and the small mines for $17.5 million or 7 percent of the total. The combination of high operating costs, low productivity, inadequate ore reserves, and insufficient risk capital for exploration and development has led to the realization that there is an urgent need to improve the situation for mining in Bolivia. Proposals are being studied to revise the tax code, a program is underway to evaluate selected mineral deposits for possible exploration and development, and programs are under consideration to encourage minerals exploration. A minerals exploration plan is proposed which would offer technical and financial aid to various segments in the minerals field. A program, estimated to cost between $2 million and $2.5 million annually, and to be operated by a new agency in the Ministry of Mining and Metallurgy, is outlined.

Potential for improved extraction of tellurium as a byproduct of current copper mining processes

NASA Astrophysics Data System (ADS)

Hayes, S. M.; Spaleta, K. J.; Skidmore, A. E.

2016-12-01

Tellurium (Te) is classified as a critical element due to its increasing use in high technology applications, low average crustal abundance (3 μg kg-1), and primary source as a byproduct of copper extraction. Although Te can be readily recovered from copper processing, previous studies have estimated a 4 percent extraction efficiency, and few studies have addressed Te behavior during the entire copper extraction process. The goals of the present study are to perform a mass balance examining Te behavior during copper extraction and to connect these observations with mineralogy of Te-bearing phases which are essential first steps in devising ways to optimize Te recovery. Our preliminary mass balance results indicate that less than 3 percent of Te present in copper ore is recovered, with particularly high losses during initial concentration of copper ore minerals by flotation. Tellurium is present in the ore in telluride minerals (e.g., Bi-Te-S phases, altaite, and Ag-S-Se-Te phases identified using electron microprobe) with limited substitution into sulfide minerals (possibly 10 mg kg-1 Te in bulk pyrite and chalcopyrite). This work has also identified Te accumulation in solid-phase intermediate extraction products that could be further processed to recover Te, including smelter dusts (158 mg kg-1) and pressed anode slimes (2.7 percent by mass). In both the smelter dusts and anode slimes, X-ray absorption spectroscopy indicates that about two thirds of the Te is present as reduced tellurides. In anode slimes, electron microscopy shows that the remaining Te is present in an oxidized form in a complex Te-bearing oxidate phase also containing Pb, Cu, Ag, As, Sb, and S. These results clearly indicate that more efficient, increased recovery of Te may be possible, likely at minimal expense from operating copper processing operations, thereby providing more Te for manufacturing of products such as inexpensive high-efficiency solar panels.

Mineral deposit densities for estimating mineral resources

USGS Publications Warehouse

Singer, Donald A.

2008-01-01

Estimates of numbers of mineral deposits are fundamental to assessing undiscovered mineral resources. Just as frequencies of grades and tonnages of well-explored deposits can be used to represent the grades and tonnages of undiscovered deposits, the density of deposits (deposits/area) in well-explored control areas can serve to represent the number of deposits. Empirical evidence presented here indicates that the processes affecting the number and quantity of resources in geological settings are very general across many types of mineral deposits. For podiform chromite, porphyry copper, and volcanogenic massive sulfide deposit types, the size of tract that geologically could contain the deposits is an excellent predictor of the total number of deposits. The number of mineral deposits is also proportional to the type’s size. The total amount of mineralized rock is also proportional to size of the permissive area and the median deposit type’s size. Regressions using these variables provide a means to estimate the density of deposits and the total amount of mineralization. These powerful estimators are based on analysis of ten different types of mineral deposits (Climax Mo, Cuban Mn, Cyprus massive sulfide, Franciscan Mn, kuroko massive sulfide, low-sulfide quartz-Au vein, placer Au, podiform Cr, porphyry Cu, and W vein) from 108 permissive control tracts around the world therefore generalizing across deposit types. Despite the diverse and complex geological settings of deposit types studied here, the relationships observed indicate universal controls on the accumulation and preservation of mineral resources that operate across all scales. The strength of the relationships (R 2=0.91 for density and 0.95 for mineralized rock) argues for their broad use. Deposit densities can now be used to provide a guideline for expert judgment or used directly for estimating the number of most kinds of mineral deposits.

Short-term belowground responses to thinning and burning treatments in southwestern ponderosa pine forests of the USA

Treesearch

Steven T. Overby; Stephen C. Hart

2016-01-01

Microbial-mediated decomposition and nutrient mineralization are major drivers of forest productivity. As landscape-scale fuel reduction treatments are being implemented throughout the fire-prone western United States of America, it is important to evaluate operationally how these wildfire mitigation treatments alter belowground processes. We quantified these important...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

Geothermal resources and energy complex use in Russia

NASA Astrophysics Data System (ADS)

Svalova, V.

2009-04-01

Geothermal energy use is the perspective way to clean sustainable development of the world. Russia has rich high and low temperature geothermal resources and makes good steps in their use. In Russia the geothermal resources are used predominantly for heat supply both heating of several cities and settlements on Northern Caucasus and Kamchatka with a total number of the population 500000. Besides in some regions of country the deep heat is used for greenhouses of common area 465000 m2. Most active the hydrothermal resources are used in Krasnodar territory, Dagestan and on Kamchatka. The approximately half of extracted resources is applied for heat supply of habitation and industrial puttings, third - to a heating of greenhouses, and about 13 % - for industrial processes. Besides the thermal waters are used approximately on 150 health resorts and 40 factories on bottling mineral water. The most perspective direction of usage of low temperature geothermal resources is the use of heat pumps. This way is optimal for many regions of Russia - in its European part, on Ural and others. The electricity is generated by some geothermal power plants (GeoPP) only in the Kamchatka Peninsula and Kuril Islands. At present three stations work in Kamchatka: Pauzhetka GeoPP (11MW e installed capacity) and two Severo-Mutnovka GeoPP ( 12 and 50 MWe). Moreover, another GeoPP of 100 MVe is now under preparation in the same place. Two small GeoPP are in operation in Kuril's Kunashir Isl, and Iturup Isl, with installed capacity of 2,б MWe and 6 MWe respectively. There are two possible uses of geothermal resources depending on structure and properties of thermal waters: heat/power and mineral extraction. The heat/power direction is preferable for low mineralized waters when valuable components in industrial concentration are absent, and the general mineralization does not interfere with normal operation of system. When high potential geothermal waters are characterized by the high mineralization and propensity for scaling, the extraction of mineral components should be considered. The mineral-extraction direction is basic for geothermal waters, containing valuable components in industrial quantities. Thus, the ability to extract minerals is dependent upon the use and maturity of recovery technologies. For such waters the heat is an added product, which use can raise efficiency of basic mineral production processes and even to save fuel. The process of extraction of valuable components should be dominant in such systems. The most significant deposits of thermal waters represent the brines containing from 35 up to 400 and more g/l of salts. They are mineral raw materials for many chemical elements. Many brines can become deposits of valuable chemical elements: cesium, boron, strontium, tantalum, magnesium, calcium, tungsten, etc. Basically it is possible to recover iodine, bromine, boron, chloride salts of ammonium, potassium, sodium, calcium and magnesium from natural solutions using inexpensive technological solutions. Extraction of other chemical elements is complicated due to high cost of technology. There is a perspective method of ion-exchange pitches for selective extraction of certain components from natural waters. In a basis of the method there is the principle of selective sorption of ions of useful elements or their complexes in solutions with special compounds. Works of some scientific institutes in Russia strive to create the procedures of chemical processing of hydrothermal minerals to expand the spheres of its economic application. Many laboratory and natural tests on extraction of valuable components from thermal waters confirm the necessity and an opportunity of complex use of this nonconventional raw material. It is planned to recover I, Br, KCl, CaCl, NaCl from brines in Yaroslavl area. New methods of mineral and valuable elements extraction from industrial solutions are developed on the basis of biosorbent use.

30 CFR 48.7 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2010 CFR

2010-07-01

... to new work tasks as mobile equipment operators, drilling machine operators, haulage and conveyor... protective measures a miner can take against these hazards, and the contents of the mine's HazCom program... operation in the mine, which require new or different operating procedures. (4) Such other courses as may be...

43 CFR Appendix B to Part 2 - Mineral Leasing Act and Mineral Leasing Act for Acquired Lands-Special Rules

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 1 2013-10-01 2013-10-01 false Mineral Leasing Act and Mineral Leasing... 2—Mineral Leasing Act and Mineral Leasing Act for Acquired Lands—Special Rules (a) Definitions. As... conduct coal exploration operations on land subject to the Mineral Leasing Act, under 30 U.S.C. 201(b), or...

43 CFR Appendix B to Part 2 - Mineral Leasing Act and Mineral Leasing Act for Acquired Lands-Special Rules

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 1 2014-10-01 2014-10-01 false Mineral Leasing Act and Mineral Leasing... 2—Mineral Leasing Act and Mineral Leasing Act for Acquired Lands—Special Rules (a) Definitions. As... conduct coal exploration operations on land subject to the Mineral Leasing Act, under 30 U.S.C. 201(b), or...

43 CFR Appendix F to Part 2 - Mineral Leasing Act and Mineral Leasing Act for Acquired Lands-Special Rules

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 1 2011-10-01 2011-10-01 false Mineral Leasing Act and Mineral Leasing... 2—Mineral Leasing Act and Mineral Leasing Act for Acquired Lands—Special Rules (a) Definitions. As... conduct coal exploration operations on land subject to the Mineral Leasing Act, under 30 U.S.C. 201(b), or...

43 CFR Appendix F to Part 2 - Mineral Leasing Act and Mineral Leasing Act for Acquired Lands-Special Rules

Code of Federal Regulations, 2010 CFR

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Mineral Leasing Act and Mineral Leasing... 2—Mineral Leasing Act and Mineral Leasing Act for Acquired Lands—Special Rules (a) Definitions. As... conduct coal exploration operations on land subject to the Mineral Leasing Act, under 30 U.S.C. 201(b), or...

Automated classification of Acid Rock Drainage potential from Corescan drill core imagery

NASA Astrophysics Data System (ADS)

Cracknell, M. J.; Jackson, L.; Parbhakar-Fox, A.; Savinova, K.

2017-12-01

Classification of the acid forming potential of waste rock is important for managing environmental hazards associated with mining operations. Current methods for the classification of acid rock drainage (ARD) potential usually involve labour intensive and subjective assessment of drill core and/or hand specimens. Manual methods are subject to operator bias, human error and the amount of material that can be assessed within a given time frame is limited. The automated classification of ARD potential documented here is based on the ARD Index developed by Parbhakar-Fox et al. (2011). This ARD Index involves the combination of five indicators: A - sulphide content; B - sulphide alteration; C - sulphide morphology; D - primary neutraliser content; and E - sulphide mineral association. Several components of the ARD Index require accurate identification of sulphide minerals. This is achieved by classifying Corescan Red-Green-Blue true colour images into the presence or absence of sulphide minerals using supervised classification. Subsequently, sulphide classification images are processed and combined with Corescan SWIR-based mineral classifications to obtain information on sulphide content, indices representing sulphide textures (disseminated versus massive and degree of veining), and spatially associated minerals. This information is combined to calculate ARD Index indicator values that feed into the classification of ARD potential. Automated ARD potential classifications of drill core samples associated with a porphyry Cu-Au deposit are compared to manually derived classifications and those obtained by standard static geochemical testing and X-ray diffractometry analyses. Results indicate a high degree of similarity between automated and manual ARD potential classifications. Major differences between approaches are observed in sulphide and neutraliser mineral percentages, likely due to the subjective nature of manual estimates of mineral content. The automated approach presented here for the classification of ARD potential offers rapid, repeatable and accurate outcomes comparable to manually derived classifications. Methods for automated ARD classifications from digital drill core data represent a step-change for geoenvironmental management practices in the mining industry.

Spatial variation in microbial processes controlling carbon mineralization within soils and sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fendorf, Scott; Kleber, Markus; Nico, Peter

Soils have a defining role in global carbon cycling, having one of the largest dynamic stocks of C on earth—3300 Pg of C are stored in soils, which is three-times the amount stored in the atmosphere and more than the terrestrial land plants. An important control on soil organic matter (SOM) quantities is the mineralization rate. It is well recognized that the rate and extent of SOM mineralization is affected by climatic factors and mineral-organic matter associations. What remained elusive is to what extent constraints on microbial metabolism induced by the respiratory pathway, and specifically the electron acceptor in respiration,more » control overall rates of carbon mineralization in soils. Therefore, physical factors limiting oxygen diffusion such as soil texture and aggregate size (soil structure) may therefore be central controls on C mineralization rates. The goal of our research was therefore to determine if variations in microbial metabolic rates induced by anaerobic microsites in soils are a major control on SOM mineralization rates and thus storage. We performed a combination of laboratory experiments and field investigations will be performed to fulfill our research objectives. We used laboratory studies to examine fundamental factors of respiratory constraints (i.e., electron acceptor) on organic matter mineralization rates. We ground our laboratory studies with both manipulation of field samples and in-field measurements. Selection of the field sites is guided by variation in soil texture and structure while having (other environmental/soil factors constant. Our laboratory studies defined redox gradients and variations in microbial metabolism operating at the aggregate-scale (cm-scale) within soils using a novel constructed diffusion reactor. We further examined micro-scale variation in terminal electron accepting processes and resulting C mineralization rates within re-packed soils. A major outcome of our research is the ability to quantitatively place the importance of aggregate-based heterogeneity in microbial redox processes and the resulting lack of oxygen on the rate of carbon mineralization. Collectively, our research shows that anaerobic microsites are prevalent in soils and are important regulators of soil carbon persistence, shifting microbial metabolism to less efficient anaerobic respiration and selectively protecting otherwise bioavailable, reduced organic compounds such as lipids and waxes from decomposition. Further, shifting from anaerobic to aerobic conditions leads to a 10-fold increase in volume-specific mineralization rate, illustrating the sensitivity of anaerobically protected carbon to disturbance. Vulnerability of anaerobically protected carbon to future climate or land use change thus constitutes a yet unrecognized soil carbon-climate feedback that should be incorporated into terrestrial ecosystem models.« less

Homogeneous sonophotolysis of food processing industry wastewater: Study of synergistic effects, mineralization and toxicity removal.

PubMed

Durán, A; Monteagudo, J M; Sanmartín, I; Gómez, P

2013-03-01

The mineralization of industrial wastewater coming from food industry using an emerging homogeneous sonophotolytic oxidation process was evaluated as an alternative to or a rapid pretreatment step for conventional anaerobic digestion with the aim of considerably reducing the total treatment time. At the selected operation conditions ([H(2)O(2)]=11,750ppm, pH=8, amplitude=50%, pulse length (cycles)=1), 60% of TOC is removed after 60min and 98% after 180min when treating an industrial effluent with 2114ppm of total organic carbon (TOC). This process removed completely the toxicity generated during storing or due to intermediate compounds. An important synergistic effect between sonolysis and photolysis (H(2)O(2)/UV) was observed. Thus the sonophotolysis (ultrasound/H(2)O(2)/UV) technique significantly increases TOC removal when compared with each individual process. Finally, a preliminary economical analysis confirms that the sono-photolysis with H(2)O(2) and pretreated water is a profitable system when compared with the same process without using ultrasound waves and with no pretreatment. Copyright © 2012 Elsevier B.V. All rights reserved.

77 FR 15118 - Information Collection Activities: Operations in the Outer Continental Shelf for Minerals Other...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-14

...-0005; OMB Number 1014-NEW] Information Collection Activities: Operations in the Outer Continental Shelf for Minerals Other Than Oil, Gas, and Sulphur; Submitted for Office of Management and Budget (OMB... (ICR) for approval of the paperwork requirements in the regulations under Operations in the Outer...

30 CFR 250.402 - When and how must I secure a well?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 250.402 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.402 When and how must I secure a well? Whenever you interrupt drilling operations, you must...

30 CFR 57.12071 - Movement or operation of equipment near high-voltage powerlines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Movement or operation of equipment near high-voltage powerlines. 57.12071 Section 57.12071 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION...-voltage powerlines. When equipment must be moved or operated near energized high-voltage powerlines (other...

30 CFR 250.1619 - Well records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Well records. 250.1619 Section 250.1619 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1619 Well records. (a) Complete and accurate records for each well and all well operations shall be retained for a period of 2 years at the...

Effects of High Pressure ORE Grinding on the Efficiency of Flotation Operations

NASA Astrophysics Data System (ADS)

Saramak, Daniel; Krawczykowska, Aldona; Młynarczykowska, Anna

2014-10-01

This article discusses issues related to the impact of the high pressure comminution process on the efficiency of the copper ore flotation operations. HPGR technology improves the efficiency of mineral resource enrichment through a better liberation of useful components from waste rock as well as more efficient comminution of the material. Research programme included the run of a laboratory flotation process for HPGR crushing products at different levels of operating pressures and moisture content. The test results showed that products of the high-pressure grinding rolls achieved better recoveries in flotation processes and showed a higher grade of useful components in the flotation concentrate, in comparison to the ball mill products. Upgrading curves have also been marked in the following arrangement: the content of useful component in concentrate the floatation recovery. All upgrading curves for HPGR products had a more favourable course in comparison to the curves of conventionally grinded ore. The results also indicate that various values of flotation recoveries have been obtained depending on the machine operating parameters (i.e. the operating pressure), and selected feed properties (moisture).

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Other minerals and deep-lying lead and zinc minerals. 215... LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead and zinc minerals. Except as provided in § 215.6(b), leases on Quapaw Indian lands, for mining...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Other minerals and deep-lying lead and zinc minerals. 215... LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead and zinc minerals. Except as provided in § 215.6(b), leases on Quapaw Indian lands, for mining...

43 CFR Appendix F to Part 2 - Mineral Leasing Act and Mineral Leasing Act for Acquired Lands-Special Rules

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 1 2012-10-01 2011-10-01 true Mineral Leasing Act and Mineral Leasing Act...—Mineral Leasing Act and Mineral Leasing Act for Acquired Lands—Special Rules (a) Definitions. As used in... conduct coal exploration operations on land subject to the Mineral Leasing Act, under 30 U.S.C. 201(b), or...

Mortality patterns of rock and slag mineral wool production workers: an epidemiological and environmental study.

PubMed Central

Robinson, C F; Dement, J M; Ness, G O; Waxweiler, R J

1982-01-01

An epidemiological and environmental study of rock and slag mineral wool production workers was undertaken at a plant that has been in operation since the early 1900s. Size characteristics of fibres produced by each process at the plant and data from industrial hygiene surveys were used to evaluate current and past exposures. These data suggest that the average historical airborne fibre concentration probably did not exceed 2.5 fibres/cc before 1935 and 1.0 fibre/cc after 1935. A retrospective cohort mortality study was designed to assess mortality patterns. Detailed occupational histories were compiled on all plant employees. All jobs in the plant were assigned to one of eight potential exposure categories to assess the extent and severity of mineral wool exposure and the effect of other significant exposures on employee mortality. Findings included an increase in the number of deaths due to cancer of the digestive system and non-malignant respiratory disease among workers who had over 20 years' exposure to mineral wool or who had survived 20 years since their first exposure to mineral wool. These findings are not inconsistent with those of Enterline's (Symposium on Biological Effects of Mineral Fibres, Lyon, France, September 1979) in the Thermal Insulation Manufacturers' Association's mortality study of men employed in four mineral wool plants. PMID:6279138

Corrosion of heavy minerals during weathering and diagenesis: A catalog for optical analysis

NASA Astrophysics Data System (ADS)

Andò, Sergio; Garzanti, Eduardo; Padoan, Marta; Limonta, Mara

2012-12-01

A practical classification of surface textures observed on detrital grains in sands and sandstones is proposed, in order to enhance data reproducibility among operators and to implement the use of high-resolution heavy-mineral data in studies of sediment-generation, provenance, and diagenesis. Five stages of progressive weathering (unweathered, corroded, etched, deeply etched, skeletal) are recognized for diverse detrital minerals. Archetypal grains displaying increasing degrees of corrosion are illustrated in numerous color tables for visual comparison. This catalog, specifically devised to systematically collect valuable information for paleoclimatic or diagenetic interpretation during routine grain-counting under the microscope, is here shown to represent a useful subsidiary tool to reveal the different degrees of weathering for diverse minerals in modern sands of equatorial Africa, and to identify post-depositional modifications of detrital assemblages in buried orogenic sediments of the Bengal Basin. The data thus obtained need to be interpreted by carefully considering the concentration of heavy minerals in each sample, which provides the fundamental clue to quantify the degree of heavy-mineral depletion caused by either pre-depositional or post-depositional processes. The scrutiny of dissolution effects has applications in the study of the chemical properties of minerals and of diagenetic evolution, helping us to understand the development of secondary porosity and to assess the potential of water and hydrocarbon reservoirs.

50 CFR 29.31 - Mineral ownerships in the United States.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 8 2011-10-01 2011-10-01 false Mineral ownerships in the United States... INTERIOR (CONTINUED) THE NATIONAL WILDLIFE REFUGE SYSTEM LAND USE MANAGEMENT Mineral Operations § 29.31 Mineral ownerships in the United States. Where mineral rights to lands in wildlife refuge areas are vested...

50 CFR 29.31 - Mineral ownerships in the United States.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 9 2014-10-01 2014-10-01 false Mineral ownerships in the United States... INTERIOR (CONTINUED) THE NATIONAL WILDLIFE REFUGE SYSTEM LAND USE MANAGEMENT Mineral Operations § 29.31 Mineral ownerships in the United States. Where mineral rights to lands in wildlife refuge areas are vested...

50 CFR 29.31 - Mineral ownerships in the United States.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 9 2012-10-01 2012-10-01 false Mineral ownerships in the United States... INTERIOR (CONTINUED) THE NATIONAL WILDLIFE REFUGE SYSTEM LAND USE MANAGEMENT Mineral Operations § 29.31 Mineral ownerships in the United States. Where mineral rights to lands in wildlife refuge areas are vested...

50 CFR 29.31 - Mineral ownerships in the United States.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 9 2013-10-01 2013-10-01 false Mineral ownerships in the United States... INTERIOR (CONTINUED) THE NATIONAL WILDLIFE REFUGE SYSTEM LAND USE MANAGEMENT Mineral Operations § 29.31 Mineral ownerships in the United States. Where mineral rights to lands in wildlife refuge areas are vested...

50 CFR 29.31 - Mineral ownerships in the United States.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Mineral ownerships in the United States... INTERIOR (CONTINUED) THE NATIONAL WILDLIFE REFUGE SYSTEM LAND USE MANAGEMENT Mineral Operations § 29.31 Mineral ownerships in the United States. Where mineral rights to lands in wildlife refuge areas are vested...

Mineral facilities of Africa and the Middle East

USGS Publications Warehouse

Eros, J.M.; Candelario-Quintana, Luissette

2006-01-01

This map displays over 1,500 mineral facilities in Africa and the Middle East. The mineral facilities include mines, plants, mills, or refineries of aluminum, cement, coal, copper, diamond, gold, iron and steel, nickel, platinum-group metals, salt, and silver, among others. The data used in this poster were compiled from multiple sources, including the 2004 USGS Minerals Yearbook (Africa and Middle East volume), Minerals Statistics and Information from the USGS Web site (http://minerals.usgs.gov/minerals/), and data collected by USGS minerals information country specialists. Data reflect the most recent published table of industry structure for each country. Other sources include statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Due to the sensitivity of some energy commodity data, the quality of these data should be evaluated on a country-by-country basis. Additional information and explanation is available from the country specialists. See Table 1 for general information about each mineral facility site including country, location and facility name, facility type, latitude, longitude, mineral commodity, mining method, main operating company, status, capacity, and units.

Reproducibility of CT bone densitometry: operator versus automated ROI definition.

PubMed

Louis, O; Luypaert, R; Kalender, W; Osteaux, M

1988-05-01

Intrasubject reproducibility with repeated determination of vertebral mineral density from a given set of CT images was investigated. The region of interest (ROI) in 10 patient scans was selected by four independent operators either manually or with an automated procedure separating cortical and spongeous bone, the operators being requested to interact in ROI selection. The mean intrasubject variation was found to be much lower with the automated process (0.3 to 0.6%) than with the conventional method (2.5 to 5.2%). In a second study, 10 patients were examined twice to determine the reproducibility of CT slice selection by the operator. The errors were of the same order of magnitude as in ROI selection.

Dust from mineral extraction: regulation of emissions in England

NASA Astrophysics Data System (ADS)

Marker, Brian

2013-04-01

The United Kingdom, which includes England, has fairly high levels of rainfall but sporadic droughts occur especially in the east. Mineral working gives rise to dust. Concerns about dust soiling are major source of public objections to new minerals extraction operations. Dust emissions from mineral workings are a significant cause of public concern in the United Kingdom and are recognised as sources of health concerns and nuisance. Emissions are controlled through a number of complementary sets of regulations that are generally well observed by the industry and well enforced by the relevant public authorities. comprehensive system of regulation, based on European and national law, to deal with all aspects of these operations including pollution control, planning, occupational health and safety and statutory nuisances. Most minerals applications are subject to EIA which forms that basis for planning and environmental conditions and monitoring of operations. There are limit values on PM10 and PM2.5 in air, and for potentially harmful elements (PHEs) in soils and water, derived from European regulations but, as yet, no limit values for PHEs (other than radioactive materials) in air. Stakeholder engagement is encouraged so that members of the public can express concerns during minerals operations and operators can quickly deal with these. While some effects inevitably remain, the levels of dust emissions are kept low through good site design and management, proper use of machinery which is equipped to minimise emissions, and good training of the workforce. Operational sites are required to have dust monitoring equipment located outside the site boundary so that any emerging problems can be detected and addressed quickly.

Role of mineralization inhibitors in the regulation of hard tissue biomineralization: relevance to initial enamel formation and maturation

PubMed Central

Margolis, Henry C.; Kwak, Seo-Young; Yamazaki, Hajime

2014-01-01

Vertebrate mineralized tissues, i.e., enamel, dentin, cementum, and bone, have unique hierarchical structures and chemical compositions. Although these tissues are similarly comprised of a crystalline calcium apatite mineral phase and a protein component, they differ with respect to crystal size and shape, level and distribution of trace mineral ions, the nature of the proteins present, and their relative proportions of mineral and protein components. Despite apparent differences, mineralized tissues are similarly derived by highly concerted extracellular processes involving matrix proteins, proteases, and mineral ion fluxes that collectively regulate the nucleation, growth and organization of forming mineral crystals. Nature, however, provides multiple ways to control the onset, rate, location, and organization of mineral deposits in developing mineralized tissues. Although our knowledge is quite limited in some of these areas, recent evidence suggests that hard tissue formation is, in part, controlled through the regulation of specific molecules that inhibit the mineralization process. This paper addresses the role of mineralization inhibitors in the regulation of biological mineralization with emphasis on the relevance of current findings to the process of amelogenesis. Mineralization inhibitors can also serve to maintain driving forces for calcium phosphate precipitation and prevent unwanted mineralization. Recent evidence shows that native phosphorylated amelogenins have the capacity to prevent mineralization through the stabilization of an amorphous calcium phosphate precursor phase, as observed in vitro and in developing teeth. Based on present findings, the authors propose that the transformation of initially formed amorphous mineral deposits to enamel crystals is an active process associated with the enzymatic processing of amelogenins. Such processing may serve to control both initial enamel crystal formation and subsequent maturation. PMID:25309443

A study of iron mineral transformation to reduce red mud tailings.

PubMed

Li, L Y

2001-01-01

This study examines the effects of iron mineral transformation in an aluminum extraction process on the settling behavior, and the physical and chemical properties of the resulting red mud slurry that must be disposed of. By producing a red mud with a higher solid content, the total volume of mud slurry will also be reduced for a given alumina production rate and more caustic soda will be recovered. The settling behavior and the mineralogical, physical, and physico-chemical properties of one bauxite and three red muds processed under varying conditions were analyzed based on examination of the iron mineral transformations. The properties of red muds derived from the same bauxite can differ markedly due to variations in operating conditions of the Bayer process, such as temperature and the addition of a reducing agent. The settling of red mud can be improved by converting goethite into hematite and/or magnetite to produce a mud of larger particle size, smaller specific surface area, and larger specific gravity, characteristics which reduce the total volume of mud slurry to be disposed of and which allow for less potential contamination from caustic soda. This study also found that the by-product--Bayer sodalite--has the high exchange capacity for Na+ that might contribute to the long-term environmental problems.

Managing the potential risks of using bacteria-laden water in mineral processing to protect freshwater.

PubMed

Liu, Wenying; Moran, Chris J; Vink, Sue

2013-06-18

The minerals industry is being driven to access multiple water sources and increase water reuse to minimize freshwater withdrawal. Bacteria-laden water, such as treated effluent, has been increasingly used as an alternative to freshwater for mineral processing, in particular flotation, where conditions are favorable for bacterial growth. However, the risk posed by bacteria to flotation efficiency is poorly understood. This could be a barrier to the ongoing use of this water source. This study tested the potential of a previously published risk-based approach as a management tool to both assist mine sites in quantifying the risk from bacteria, and finding system-wide cost-effective solutions for risk mitigation. The result shows that the solution of adjusting the flotation chemical regime could only partly control the risk. The second solution of using tailings as an absorbent was shown to be effective in the laboratory in reducing bacterial concentration and thus removing the threat to flotation recovery. The best solution is likely to combine internal and external approaches, that is, inside and outside processing plants. Findings in this study contribute possible methods applicable to managing the risk from water-borne bacteria to plant operations that choose to use bacteria-containing water, when attempting to minimize freshwater use, and avoiding the undesirable consequences of increasing its use.

30 CFR 250.256 - What related facilities and operations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What related facilities and operations information must accompany the DPP or DOCD? 250.256 Section 250.256 Mineral Resources BUREAU OF OCEAN ENERGY... OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Contents of Development and Production Plans...

Digital data base application to porphyry copper mineralization in Alaska; case study summary

USGS Publications Warehouse

Trautwein, Charles M.; Greenlee, David D.; Orr, Donald G.

1982-01-01

The purpose of this report is to summarize the progress in use of digital image analysis techniques in developing a conceptual model for assessing porphyry copper mineral potential. The study area consists of approximately the southern one-half of the 1? by 3? Nabesna quadrangle in east-central Alaska. The digital geologic data base consists of data compiled under the Alaskan Mineral Resource Assessment Program (AMRAP) as well as digital elevation data and Landsat spectral reflectance data from the Multispectral Scanner System. The digital data base used to develop and implement a conceptual model for porphyry-type copper mineralization consisted of 16 original data types and 18 derived data sets formatted in a grid-cell (raster) structure and registered to a map base in the Universal Transverse Mercator (UTM) projection. Minimum curvature and inverse distance squared interpolation techniques were used to generate continuous surfaces from sets of irregularly spaced data points. Processing requirements included: (1) merging or overlaying of data sets, (2) display and color coding of maps and images, (3) univariate and multivariate statistical analyses, and (4) compound overlaying operations. Data sets were merged and processed to create stereoscopic displays of continuous surfaces. The ratio of several data sets were calculated to evaluate relative variations and to enhance the display of surface alteration (gossans). Factor analysis and principal components analysis techniques were used to determine complex relationships and correlations between data sets. The resultant model consists of 10 parameters that identify three areas most likely to contain porphyry copper mineralization; two of these areas are known occurrences of mineralization and the third is not well known. Field studies confirmed that the three areas identified by the model have significant copper potential.

30 CFR 282.42 - Payments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Payments. 282.42 Section 282.42 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR Payments § 282.42 Payments. Rentals, royalties...

30 CFR 282.7 - Jurisdictional controversies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Jurisdictional controversies. 282.7 Section 282.7 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR General § 282.7...

Aerobic sludge granulation for simultaneous anaerobic decolorization and aerobic aromatic amines mineralization for azo dye wastewater treatment.

PubMed

Yan, Lawrence K Q; Fung, Ka Y; Ng, Ka M

2018-06-01

In this study, the capability of using aerobic granules to undergo simultaneous anaerobic decolorization and aerobic aromatic amines degradation was demonstrated for azo dye wastewater treatment. An integrated acclimation-granulation process was devised, with Mordant Orange 1 as the model pollutant. Performance tests were carried out in a batch column reactor to evaluate the effect of various operating parameters. The optimal condition was to use 1.0-1.7 mm (1.51 ± 0.33 mm) granules, 5 g/L biomass, and 4000 mg/L organics as nutrient; and supplement the wastewater with 1  mg/L dissolved oxygen. This led to a dye mineralization of 61 ± 2%, an anaerobic dye removal of 88 ± 1%, and an aerobic aromatic amines removal of 70 ± 3% within 48 h. This study showed that simultaneous anaerobic/aerobic process by aerobic granules could be a possible alternative to the conventional activated sludge process.

The study of the mobile compressor unit heat losses recovery system waste heat exchanger thermal insulation types influence on the operational efficiency

NASA Astrophysics Data System (ADS)

Yusha, V. L.; Chernov, G. I.; Kalashnikov, A. M.

2017-08-01

The paper examines the mobile compressor unit (MCU) heat losses recovery system waste heat exchanger prototype external thermal insulation types influence on the operational efficiency. The study is conducted by means of the numerical method through the modellingof the heat exchange processes carried out in the waste heat exchanger in ANSUS. Thermaflex, mineral wool, penofol, water and air were applied as the heat exchanger external insulation. The study results showed the waste heat exchanger external thermal insulationexistence or absence to have a significant impact on the heat exchanger operational efficiency.

Interfacial properties and coal cleaning in the LICADO process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chi, S.M.B.

1986-01-01

The LICADO LIquid CArbon DiOxide process is currently being investigated as a new technique for cleaning coal. It relies on the relative wettability of clean coal and mineral particles between liquid CO/sub 2/ and water so that when liquid CO/sub 2/ is dispersed into a coal-water slurry, it tends to form agglomerates with the clean coal particles and float them to the liquid CO/sub 2/ phase. The mineral particles, on the other hand, remain in the aqueous phase as refuse. Since the surface/interfacial properties of fine coal particles play such an important role in this coal cleaning operation, an understandingmore » of their behavior becomes indispensable. In order to understand the separation mechanisms involved in the LICADO process, it is necessary to study the interfacial interactions occurring in the CO/sub 2/-water-coal system. It is believed that a relationship between the process performance and the wetting characteristics of the coal/refuse particles can be established. Upper Freeport -200 mesh coal from Indiana County, PA with 23.5% ash content was selected for the experimental work. A specially designed high pressure experimental unit, equipped with necessary optical and photographic accessories, was constructed for this study. Contact angles were also measured on the coal surface under two different sample pretreatment conditions: water-first-wet and liquid CO/sub 2/-first-wet. The results infer that an optimum mixing is necessary to provide sufficient shear force to expose the clean coal particles to the CO/sub 2/ droplets. The coal maceral and mineral association on the coal particle surface was determined based on the reflective grey level distinction between the mineral and Litho-type of various coal components.« less

Degradation of a cationic dye (Rhodamine 6G) using hydrodynamic cavitation coupled with other oxidative agents: Reaction mechanism and pathway.

PubMed

Rajoriya, Sunil; Bargole, Swapnil; Saharan, Virendra Kumar

2017-01-01

In the present study, decolorization and mineralization of a cationic dye, Rhodamine 6G (Rh6G), has been carried out using hydrodynamic cavitation (HC). Two cavitating devices such as slit and circular venturi were used to generate cavitation in HC reactor. The process parameters such as initial dye concentration, solution pH, operating inlet pressure, and cavitation number were investigated in detail to evaluate their effects on the decolorization efficiency of Rh6G. Decolorization of Rh6G was marginally higher in the case of slit venturi as compared to circular venturi. The kinetic study showed that decolorization and mineralization of the dye fitted first-order kinetics. The loadings of H 2 O 2 and ozone have been optimized to intensify the decolorization and mineralization efficiency of Rh6G using HC. Nearly 54% decolorization of Rh6G was obtained using a combination of HC and H 2 O 2 at a dye to H 2 O 2 molar ratio of 1:30. The combination of HC with ozone resulted in 100% decolorization in almost 5-10min of processing time depending upon the initial dye concentration. To quantify the extent of mineralization, total organic carbon (TOC) analysis was also performed using various processes and almost 84% TOC removal was obtained using HC coupled with 3g/h of ozone. The degradation by-products formed during the complete degradation process were qualitatively identified by liquid chromatography-mass spectrometry (LC-MS) and a detailed degradation pathway has been proposed. Copyright © 2016 Elsevier B.V. All rights reserved.

Ultrasound-assisted advanced oxidation processes for water decontamination.

PubMed

Ince, Nilsun H

2018-01-01

The study reflects a part of my experience in sonochemistry and ultrasound-assisted advanced oxidation processes (AOPs) acquired during the last fifteen years with my research team. The data discussed were selected from studies with azo dyes, endocrine disrupting compounds and analgesic/anti-inflammatory pharmaceuticals, which are all classified as "hazardous" or "emerging" contaminants. The research focused on their treatability by ultrasound (US) and AOPs with emphasis on the mineralization of organic carbon. Some of the highlights as pointed out in the manuscript are: i) ultrasound is capable of partially or completely oxidizing the above contaminant groups if the operating conditions are properly selected and optimized, but incapable of mineralizing them; ii) the mechanism of degradation in homogeneous solutions is OH-mediated oxidation in the bulk solution or at the bubble-liquid interface, depending on the molecular properties of the contaminant, the applied frequency and pH; iii) US-assisted AOPs such as ozonation, UV/peroxide, Fenton and UV/Fenton are substantially more effective than ultrasound alone, particularly for the mineralization process; iv) catalytic processes involving TiO 2 , alumina and zero-valent iron and assisted by ultrasound are promising options not only for the destruction of the parent compounds, but also for the mineralization of their oxidation byproducts. The degradation reactions in heterogeneous solutions take place mostly at the catalyst surface despite the high-water solubility of the compounds; v) sonolytic modification of the above catalysts to reduce their particle size (to nano-levels) or to decorate the surface with metallic nanoparticles increases the catalytic activity under sonolysis, photolysis and both, and improves the stability of the catalyst. Copyright © 2017 Elsevier B.V. All rights reserved.

30 CFR 48.11 - Hazard training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hazard training. 48.11 Section 48.11 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING TRAINING AND RETRAINING OF MINERS Training and Retraining of Underground Miners § 48.11 Hazard training. (a) Operators...

The mineral economy of Brazil--Economia mineral do Brasil

USGS Publications Warehouse

Gurmendi, Alfredo C.; Barboza, Frederico Lopes; Thorman, Charles H.

1999-01-01

This study depicts the Brazilian government structure, mineral legislation and investment policy, taxation, foreign investment policies, environmental laws and regulations, and conditions in which the mineral industry operates. The report underlines Brazil's large and diversified mineral endowment. A total of 37 mineral commodities, or groups of closely related commodities, is discussed. An overview of the geologic setting of the major mineral deposits is presented. This report is presented in English and Portuguese in pdf format.

Biomining-biotechnologies for extracting and recovering metals from ores and waste materials.

PubMed

Johnson, D Barrie

2014-12-01

The abilities of acidophilic chemolithotrophic bacteria and archaea to accelerate the oxidative dissolution of sulfide minerals have been harnessed in the development and application of a biotechnology for extracting metals from sulfidic ores and concentrates. Biomining is currently used primarily to leach copper sulfides and as an oxidative pretreatment for refractory gold ores, though it is also used to recover other base metals, such as cobalt, nickel and zinc. Recent developments have included using acidophiles to process electronic wastes, to extract metals from oxidized ores, and to selectively recover metals from process waters and waste streams. This review describes the microorganisms and mechanisms involved in commercial biomining operations, how the technology has developed over the past 50 years, and discusses the challenges and opportunities for mineral biotechnologies in the 21st century. Copyright © 2014 Elsevier Ltd. All rights reserved.

[Nutritional status, body composition and bone mineral density in gastric bypass females: impact of socioeconomic level].

PubMed

de la Maza, María Pía; Leiva, Laura; Barrera, Gladys; Boggiano, Carolina; Herrera, Tomás; Pérez, Yanet; Gattás, Vivien; Bunout, Daniel; Hirsch, Sandra

2008-11-01

Roux-en-Y gastric bypass (RYGBP) has had a posilive impact on co-mobidities associated with obesity. However, in the long-term it can induce micronutrient deficiencies. To petform a complete nutritional assessment in a group of women previously operated of RYGBP from different socioeconomic levels (SEL). Thirtyy three women (19 high SEL and 14 low SEL), were assessed by dietary recalls, anthropometric measurements, muscle strength, bone mineral density, routine clinical laboratory, semm leeds of vitamin B12, 25OH-vitamin D, folate, calcium, ferritine ceruloplasmin and indicators of bone tutnoter (paratbohormone, osteocalcin and urinary pyridinolines). Their values were compared to those of 30 control women (18 high SEL and 12 low SEL). Low SEL operated women consumed fewer vitamin and mineral supplements compared with their high SEL pairs. No cases of vitamin B12, folic acid or copper deficiencies were detected. Frequency of iron deficiency was similar in patients and controls. Vitamin D insufficiency was higher among patients than in controls (p = 0.047), regardless SEL. Patients had also a higher frequency of high senum P771 and osteocakin and urinary pyridinoline levels. However, no differences in bone mineral density were obseived between operated women and controls. Vitamin and mineral deficiencies were lower than expected among operated women. However problems associated with vitamin D deficiency were highly prevalent among patients operated of RYGBP, irrespective SEL. These alterations were only detectable through specific markers at this stage, because they did not translate into lower bone mineral density (BMD) of sutgical patients, probably due to the higher pre-operative BMD of these moibid obese patients

30 CFR 581.19 - Lease term.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Lease term. 581.19 Section 581.19 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER... thereafter as leased OCS minerals are being produced in accordance with an approved mining operation or the...

30 CFR 581.19 - Lease term.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Lease term. 581.19 Section 581.19 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER... thereafter as leased OCS minerals are being produced in accordance with an approved mining operation or the...

30 CFR 581.19 - Lease term.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Lease term. 581.19 Section 581.19 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER... thereafter as leased OCS minerals are being produced in accordance with an approved mining operation or the...

30 CFR 282.41 - Method of royalty calculation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Method of royalty calculation. 282.41 Section 282.41 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR Payments § 282.41 Method...

30 CFR 282.1 - Purpose and authority.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Purpose and authority. 282.1 Section 282.1 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR General § 282.1 Purpose and authority. (a) The...

30 CFR 282.4 - Opportunities for review and comment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Opportunities for review and comment. 282.4 Section 282.4 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR General § 282.4...

30 CFR 282.0 - Authority for information collection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Authority for information collection. 282.0 Section 282.0 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR General § 282.0...

30 CFR 550.246 - What mineral resource conservation information must accompany the DPP or DOCD?

Code of Federal Regulations, 2013 CFR

2013-07-01

... SHELF Plans and Information Contents of Development and Production Plans (dpp) and Development Operations Coordination Documents (docd) § 550.246 What mineral resource conservation information must... 30 Mineral Resources 2 2013-07-01 2013-07-01 false What mineral resource conservation information...

30 CFR 550.246 - What mineral resource conservation information must accompany the DPP or DOCD?

Code of Federal Regulations, 2014 CFR

2014-07-01

... SHELF Plans and Information Contents of Development and Production Plans (dpp) and Development Operations Coordination Documents (docd) § 550.246 What mineral resource conservation information must... 30 Mineral Resources 2 2014-07-01 2014-07-01 false What mineral resource conservation information...

30 CFR 550.246 - What mineral resource conservation information must accompany the DPP or DOCD?

Code of Federal Regulations, 2012 CFR

2012-07-01

... SHELF Plans and Information Contents of Development and Production Plans (dpp) and Development Operations Coordination Documents (docd) § 550.246 What mineral resource conservation information must... 30 Mineral Resources 2 2012-07-01 2012-07-01 false What mineral resource conservation information...

30 CFR 217.200 - Audits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Audits. 217.200 Section 217.200 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR MINERALS REVENUE MANAGEMENT AUDITS AND INSPECTIONS Coal § 217.200 Audits. An audit of the accounts and books of operators/lessees for the purpose of...

36 CFR 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... mineral leasing. 1005.14 Section 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing laws are...

36 CFR 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... mineral leasing. 1005.14 Section 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing laws are...

36 CFR 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... mineral leasing. 1005.14 Section 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing laws are...

30 CFR 780.37 - Road systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Road systems. 780.37 Section 780.37 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.37 Road systems...

30 CFR 780.37 - Road systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Road systems. 780.37 Section 780.37 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.37 Road systems...

30 CFR 780.37 - Road systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Road systems. 780.37 Section 780.37 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.37 Road systems...

Thermophilic microorganisms in biomining.

PubMed

Donati, Edgardo Rubén; Castro, Camila; Urbieta, María Sofía

2016-11-01

Biomining is an applied biotechnology for mineral processing and metal extraction from ores and concentrates. This alternative technology for recovering metals involves the hydrometallurgical processes known as bioleaching and biooxidation where the metal is directly solubilized or released from the matrix for further solubilization, respectively. Several commercial applications of biomining can be found around the world to recover mainly copper and gold but also other metals; most of them are operating at temperatures below 40-50 °C using mesophilic and moderate thermophilic microorganisms. Although biomining offers an economically viable and cleaner option, its share of the world´s production of metals has not grown as much as it was expected, mainly considering that due to environmental restrictions in many countries smelting and roasting technologies are being eliminated. The slow rate of biomining processes is for sure the main reason of their poor implementation. In this scenario the use of thermophiles could be advantageous because higher operational temperature would increase the rate of the process and in addition it would eliminate the energy input for cooling the system (bioleaching reactions are exothermic causing a serious temperature increase in bioreactors and inside heaps that adversely affects most of the mesophilic microorganisms) and it would decrease the passivation of mineral surfaces. In the last few years many thermophilic bacteria and archaea have been isolated, characterized, and even used for extracting metals. This paper reviews the current status of biomining using thermophiles, describes the main characteristics of thermophilic biominers and discusses the future for this biotechnology.

Logistic Principles Application for Managing the Extraction and Transportation of Solid Minerals

NASA Astrophysics Data System (ADS)

Tyurin, Alexey

2017-11-01

Reducing the cost of resources in solid mineral extraction is an urgent task. For its solution the article proposes logistic approach use to management of mining company all resources, including extraction processes, transport, mineral handling and storage. The account of the uneven operation of mining, transport units and complexes for processing and loading coal into railroad cars allows you to identify the shortcomings in the work of the entire enterprise and reduce resources use at the planned production level. In the article the mining planning model taking into account the dynamics of the production, transport stations and export coal to consumers rail transport on example of Krasnoyarsk region Nazarovo JSC «Razrez Sereul'skiy». Rolling planning methods use and data aggregation allows you to split the planning horizon (month) on equal periods and to use of dynamic programming method for building mining optimal production programme for the month. Coal mining production program definition technique will help align the work of all enterprise units, to optimize resources of all areas, to establish a flexible relationship between manufacturer and consumer, to take into account the irregularity of rail transport.

Earth Obsersation taken by the Expedition 11 crew

NASA Image and Video Library

2005-06-27

ISS011-E-09680 (27 June 2005) --- Searles Lake, California is featured in this image photographed by an Expedition 11 crewmember on the International Space Station. Searles Lake is known for the abundance of rare elements and evaporite minerals, such as trona, hanksite, and halite formed within its sediments. These minerals dissolve in water or very humid environments. According to NASA scientists who are studying the Space Station photography, during the Pleistocene Epoch (beginning approximately two million years ago), Searles Lake was one of a chain of lakes fed by streamflow from the Sierra Nevada to the west. Lake levels rose and fell dependant on glacial outwash from the Sierra Nevada as climates shifted. Successive layers of sediment were deposited as lake levels fluctuated, preserving an important record of regional climate change. The lakes gradually dried up completely as climatic conditions became hotter and drier (as today), forming a string of enclosed basins with no outlets (playas). This photograph depicts the Searles Lake playa (characterized by white surface mineral deposits) bounded by the Argus and Slate Mountains. The width of the playa is approximately 10 kilometers. The center of the image is dominated by mining operations that extract sodium- and potassium-rich minerals (primarily borax and salt) for industrial use. Minerals are primarily in naturally-occurring brines that are pumped to the surface and evaporated to crystallize the minerals. A large evaporation pond (black) is visible in the center of the image. Further processing concentrates the minerals and removes excess water.

Modeling particulate matter emissions during mineral loading process under weak wind simulation.

PubMed

Zhang, Xiaochun; Chen, Weiping; Ma, Chun; Zhan, Shuifen

2013-04-01

The quantification of particulate matter emissions from mineral handling is an important problem for the quantification of global emissions on industrial sites. Mineral particulate matter emissions could adversely impact environmental quality in mining regions, transport regions, and even on a global scale. Mineral loading is an important process contributing to mineral particulate matter emissions, especially under weak wind conditions. Mathematical models are effective ways to evaluate particulate matter emissions during the mineral loading process. The currently used empirical models based on the form of a power function do not predict particulate matter emissions accurately under weak wind conditions. At low particulate matter emissions, the models overestimated, and at high particulate matter emissions, the models underestimated emission factors. We conducted wind tunnel experiments to evaluate the particulate matter emission factors for the mineral loading process. A new approach based on the mathematical form of a logistical function was developed and tested. It provided a realistic depiction of the particulate matter emissions during the mineral loading process, accounting for fractions of fine mineral particles, dropping height, and wind velocity. Copyright © 2013 Elsevier B.V. All rights reserved.

30 CFR 795.8 - Application approval and notice.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Application approval and notice. 795.8 Section 795.8 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SMALL OPERATOR ASSISTANCE PERMANENT REGULATORY PROGRAM-SMALL OPERATOR ASSISTANCE PROGRAM § 795.8...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 41.12 - Changes; notification by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Changes; notification by operator. 41.12 Section 41.12 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR FILING AND OTHER ADMINISTRATIVE REQUIREMENTS NOTIFICATION OF LEGAL IDENTITY Notification of Legal Identity § 41.12...

30 CFR 41.12 - Changes; notification by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Changes; notification by operator. 41.12 Section 41.12 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR FILING AND OTHER ADMINISTRATIVE REQUIREMENTS NOTIFICATION OF LEGAL IDENTITY Notification of Legal Identity § 41.12...

30 CFR 250.1634 - Site security.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1634 Site security. (a) All locations... Regional Supervisor as soon as possible but no later than the next business day after discovery of the...

Recent trends in Cuba’s mining and petroleum industries

USGS Publications Warehouse

Wacaster, Susan; Baker, Michael S.; Soto-Viruet, Yadira; Textoris, Steven D.

2015-03-31

In response to recent diplomatic developments between Cuba and the United States, the National Minerals Information Center compiled available information on the mineral industries of Cuba. This fact sheet highlights a new map and table that identify mines, mineral processing facilities, and petroleum facilities as well as information on location, operational status, and ownership. It also addresses the current status of known mineral industry projects, historical developments, and trends of the Cuban economy with an emphasis on mineral industries, and the supply and demand for Cuba’s mineral resources.In 2013, Cuba was estimated to be among the world’s top ten producers of cobalt and nickel, which are the country’s leading exports. Cuba’s current crude oil and associated natural gas production from onshore and shallow water coastal reservoirs is approximately 50,000 barrels per day of liquids and about 20,000 barrels per day oil equivalent of natural gas. In 2013, the value of mining and quarrying activities accounted for 0.6 percent of Cuba’s gross domestic product (GDP), compared with 1.4 percent in 2000. The value of production from Cuba’s industrial manufacturing sector increased by 88 percent between 1993 and 2013, whereas the sector’s share in the GDP decreased by about 3 percent during the same time period reflecting economic growth in other sectors of the economy.

30 CFR 285.638 - What must I do upon completion of my commercial operations as approved in my COP or FERC license?

Code of Federal Regulations, 2010 CFR

2010-07-01

... operations as approved in my COP or FERC license? 285.638 Section 285.638 Mineral Resources MINERALS... FACILITIES ON THE OUTER CONTINENTAL SHELF Plans and Information Requirements Activities Under An Approved Cop § 285.638 What must I do upon completion of my commercial operations as approved in my COP or FERC...

30 CFR 57.22204 - Main fan operation and inspection (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main fan operation and inspection (I-A, II-A, III, and V-A mines). 57.22204 Section 57.22204 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... Main fan operation and inspection (I-A, II-A, III, and V-A mines). Main fans shall be— (a) Provided...

30 CFR 203.54 - How does my relief arrangement for an oil and gas lease operate if prices rise sharply?

Code of Federal Regulations, 2010 CFR

2010-07-01

... gas lease operate if prices rise sharply? 203.54 Section 203.54 Mineral Resources MINERALS MANAGEMENT... arrangement for an oil and gas lease operate if prices rise sharply? In those months when your current reference price rises by at least 25 percent above your base reference price, you must pay the effective...

30 CFR 57.22204 - Main fan operation and inspection (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Main fan operation and inspection (I-A, II-A, III, and V-A mines). 57.22204 Section 57.22204 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... Main fan operation and inspection (I-A, II-A, III, and V-A mines). Main fans shall be— (a) Provided...

30 CFR 282.6 - Disclosure of data and information to an adjacent State.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Disclosure of data and information to an adjacent State. 282.6 Section 282.6 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER CONTINENTAL SHELF FOR MINERALS OTHER THAN OIL, GAS, AND SULPHUR...

36 CFR § 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... mineral leasing. § 1005.14 Section § 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing...

Mineral Property Management - Division of Mining, Land, and Water

Science.gov Websites

Mineral Property Management This section in the division maintains the records for mineral property rights established under state laws and regulations. The timely maintenance of property right records is fundamental to the mineral industry operating. Property right records must be current and up-to-date for title

30 CFR 62.120 - Action level.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Action level. 62.120 Section 62.120 Mineral... OCCUPATIONAL NOISE EXPOSURE § 62.120 Action level. If during any work shift a miner's noise exposure equals or exceeds the action level the mine operator must enroll the miner in a hearing conservation program that...

30 CFR 62.120 - Action level.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Action level. 62.120 Section 62.120 Mineral... OCCUPATIONAL NOISE EXPOSURE § 62.120 Action level. If during any work shift a miner's noise exposure equals or exceeds the action level the mine operator must enroll the miner in a hearing conservation program that...

Photo-Fenton and Fenton-like processes for the treatment of the antineoplastic drug 5-fluorouracil under simulated solar radiation.

PubMed

Koltsakidou, Α; Antonopoulou, M; Sykiotou, M; Εvgenidou, Ε; Konstantinou, I; Lambropoulou, D A

2017-02-01

In the present study, photo-Fenton and Fenton-like processes were investigated for the degradation and mineralization of the antineoplastic drug 5-fluorouracil (5-FU). For the optimization of photo-Fenton treatment under simulated solar light (SSL) radiation, the effects of several operating parameters (i.e., 5-FU concentration, Fe 3+ , and oxidant concentration) on the treatment efficiency were studied. According to the results, SSL/[Fe(C 2 Ο 4 ) 3 ] 3- /Η 2 Ο 2 process was the most efficient, since faster degradation of 5-FU and higher mineralization percentages were achieved. All the applied processes followed quite similar transformation routes which include defluorination-hydroxylation as well as pyrimidine ring opening, as demonstrated by the transformation products identified by high resolution mass spectrometry analysis. The toxicity of the treated solutions was evaluated using the Microtox assay. In general, low toxicity was recorded for the initial solution and the solution at the end of the photocatalytic treatment, while an increase in the overall toxicity was observed only at the first stages of SSL/Fe 3+ /Η 2 Ο 2 and SSL/Fe 3+ /S 2 O 8 2- processes.

Advanced oxidation and disinfection processes for onsite net-zero greywater reuse: A review.

PubMed

Gassie, Lucien W; Englehardt, James D

2017-11-15

Net-zero greywater (NZGW) reuse, or nearly closed-loop recycle of greywater for all original uses, can recover both water and its attendant hot-water thermal energy, while avoiding the installation and maintenance of a separate greywater sewer in residential areas. Such a system, if portable, could also provide wash water for remote emergency health care units. However, such greywater reuse engenders human contact with the recycled water, and hence superior treatment. The purpose of this paper is to review processes applicable to the mineralization of organics, including control of oxidative byproducts such as bromate, and maintenance of disinfection consistent with potable reuse guidelines, in NZGW systems. Specifically, TiO 2 -UV, UV-hydrogen peroxide, hydrogen peroxide-ozone, ozone-UV advanced oxidation processes, and UV, ozone, hydrogen peroxide, filtration, and chlorine disinfection processes were reviewed for performance, energy demand, environmental impact, and operational simplicity. Based on the literature reviewed, peroxone is the most energy-efficient process for organics mineralization. However, in portable applications where delivery of chemicals to the site is a concern, the UV-ozone process appears promising, at higher energy demand. In either case, reverse osmosis, nanofiltration, or ED may be useful in controlling the bromide precursor in make-up water, and a minor side-stream of ozone may be used to prevent microbial regrowth in the treated water. Where energy is not paramount, UV-hydrogen peroxide and UV-TiO 2 can be used to mineralize organics while avoiding bromate formation, but may require a secondary process to prevent microbial regrowth. Chlorine and ozone may be useful for maintenance of disinfection residual. Copyright © 2017 Elsevier Ltd. All rights reserved.

30 CFR 750.15 - Coal exploration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal exploration. 750.15 Section 750.15 Mineral... PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.15 Coal exploration. Coal exploration operations on Indian lands shall be conducted in accordance with 25 CFR part 216...

30 CFR 750.15 - Coal exploration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal exploration. 750.15 Section 750.15 Mineral... PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.15 Coal exploration. Coal exploration operations on Indian lands shall be conducted in accordance with 25 CFR part 216...

30 CFR 750.15 - Coal exploration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal exploration. 750.15 Section 750.15 Mineral... PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.15 Coal exploration. Coal exploration operations on Indian lands shall be conducted in accordance with 25 CFR part 216...

30 CFR 750.15 - Coal exploration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal exploration. 750.15 Section 750.15 Mineral... PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.15 Coal exploration. Coal exploration operations on Indian lands shall be conducted in accordance with 25 CFR part 216...

30 CFR 750.15 - Coal exploration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal exploration. 750.15 Section 750.15 Mineral... PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.15 Coal exploration. Coal exploration operations on Indian lands shall be conducted in accordance with 25 CFR part 216...

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

30 CFR 77.211 - Draw-off tunnels; stockpiling and reclaiming operations; general.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Draw-off tunnels; stockpiling and reclaiming operations; general. 77.211 Section 77.211 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.211 Draw-off tunnels; stockpiling and...

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Mud program. 250.1614 Section 250.1614 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614 Mud program. (a) The quantities, characteristics, use, and testing of drilling mud and the related drilling procedures shall be designed and...

30 CFR 70.220 - Status change reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... to all miners expected to wear a CPDM. The training shall be completed prior to a miner wearing a... cutting machine. On the cutting machine operator or on the cutting machine within 36 inches inby the normal working position; (2) Conventional section blasting off the solid. On the loading machine operator...

30 CFR 285.405 - How do I designate an operator?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 285.405 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE ENERGY ALTERNATE USES OF EXISTING FACILITIES ON THE OUTER CONTINENTAL SHELF Lease and Grant... identify the new designated operator within 72 hours on a form approved by MMS. The lessee(s) or grantee(s...

30 CFR 250.602 - Equipment movement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Workover Operations § 250.602 Equipment movement... surface with a pump-through-type tubing plug and at the surface with a closed master valve prior to moving...

30 CFR 250.502 - Equipment movement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations § 250.502 Equipment movement... surface with a pump-through-type tubing plug and at the surface with a closed master valve prior to moving...

25 CFR 225.30 - Bonds.

Code of Federal Regulations, 2010 CFR

2010-04-01

... AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS OIL AND GAS, GEOTHERMAL, AND SOLID MINERALS... Circular No. 570). (b) An operator may file a $75,000 bond for all geothermal, mining, or oil and gas... operator may file a $150,000 bond for full nationwide coverage to cover all geothermal or oil and gas...

25 CFR 225.30 - Bonds.

Code of Federal Regulations, 2011 CFR

2011-04-01

... AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS OIL AND GAS, GEOTHERMAL, AND SOLID MINERALS... Circular No. 570). (b) An operator may file a $75,000 bond for all geothermal, mining, or oil and gas... operator may file a $150,000 bond for full nationwide coverage to cover all geothermal or oil and gas...

30 CFR 250.430 - When must I install a diverter system?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 250.430 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter... before you drill a conductor or surface hole. The diverter system consists of a diverter sealing element...

30 CFR 250.466 - What records must I keep?

Code of Federal Regulations, 2010 CFR

2010-07-01

....466 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to... records for each well. You must keep drilling records onsite while drilling activities continue. After...

30 CFR 250.407 - What tests must I conduct to determine reservoir characteristics?

Code of Federal Regulations, 2010 CFR

2010-07-01

... reservoir characteristics? 250.407 Section 250.407 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.407 What tests must I conduct to determine...

30 CFR 250.246 - What mineral resource conservation information must accompany the DPP or DOCD?

Code of Federal Regulations, 2011 CFR

2011-07-01

... OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Contents of Development and Production Plans (dpp) and Development Operations Coordination Documents (docd) § 250.246 What mineral resource... information, as applicable, must accompany your DPP or DOCD: (a) Technology and reservoir engineering...

Integrated electrocoagulation-electrooxidation process for the treatment of soluble coffee effluent: Optimization of COD degradation and operation time analysis.

PubMed

Ibarra-Taquez, Harold N; GilPavas, Edison; Blatchley, Ernest R; Gómez-García, Miguel-Ángel; Dobrosz-Gómez, Izabela

2017-09-15

Soluble coffee production generates wastewater containing complex mixtures of organic macromolecules. In this work, a sequential Electrocoagulation-Electrooxidation (EC-EO) process, using aluminum and graphite electrodes, was proposed as an alternative way for the treatment of soluble coffee effluent. Process operational parameters were optimized, achieving total decolorization, as well as 74% and 63.5% of COD and TOC removal, respectively. The integrated EC-EO process yielded a highly oxidized (AOS = 1.629) and biocompatible (BOD 5 /COD ≈ 0.6) effluent. The Molecular Weight Distribution (MWD) analysis showed that during the EC-EO process, EC effectively decomposed contaminants with molecular weight in the range of 10-30 kDa. In contrast, EO was quite efficient in mineralization of contaminants with molecular weight higher than 30 kDa. A kinetic analysis allowed determination of the time required to meet Colombian permissible discharge limits. Finally, a comprehensive operational cost analysis was performed. The integrated EC-EO process was demonstrated as an efficient alternative for the treatment of industrial effluents resulting from soluble coffee production. Copyright © 2017 Elsevier Ltd. All rights reserved.

Idaho and Montana non-fuel exploration database 1980-1997

USGS Publications Warehouse

Buckingham, David A.; DiFrancesco, Carl A.; Porter, Kenneth E.; Bleiwas, Donald I.; Causey, J. Douglas; Ferguson, William B.

2006-01-01

This report describes a relational database containing information about mineral exploration projects in the States of Idaho and Montana for the years 1980 through 1997 and a spatial (geographic) database constructed using data from the relational database. The focus of this project was to collect information on exploration for mineral commodities with the exception of sand, gravel, coal, geothermal, oil, and gas. The associate databases supplied with this report are prototypes that can be used or modified as needed. The following sources were used to create the databases-serial mining periodicals; annual mineral publications; mining company reports; U.S. Bureau of Mines (USBM) and U.S. Geological Survey (USGS) publications; an Idaho mineral property data base developed by Dave Boleneus, USGS, Spokane, Washington; Montana state publications; and discussions with representatives of Montana, principally the Montana Bureau of Mines and Geology and the Department of Environmental Quality. Fifty commodity groups were reported between the 596 exploration projects identified in this study. Precious metals (gold, silver, or platinum group elements) were the primary targets for about 67 percent of the exploration projects. Information on 17 of the projects did not include commodities. No location could be determined for 51 projects, all in Idaho. During the time period evaluated, some mineral properties were developed into large mining operations (for example Beal Mountain Mine, Stillwater Mine, Troy Mine, Montana Tunnels Mine) and six properties were reclaimed. Environmental Impact Statements were done on four properties. Some operating mines either closed or went through one or more shutdowns and re-openings. Other properties, where significant resources were delineated by recent exploration during this time frame, await the outcome of important factors for development such as defining additional reserves, higher metal prices, and the permitting process. Many of these projects examined relatively minor mineral occurrences. Approximately half of the exploration projects are located on Federal lands and about 40 percent were on lands managed by the U.S. Forest Service. More than 75 percent of the exploration occurred in areas with significant previous mineral activity.

Comparison of various advanced oxidation processes used in remediation of industrial wastewater laden with recalcitrant pollutants

NASA Astrophysics Data System (ADS)

Krishnan, S.; Rawindran, H.; Sinnathambi, C. M.; Lim, J. W.

2017-06-01

Due to the scarcity of water, it has become a necessity to improve the quality of wastewater that is discharged into the environment. Conventional wastewater treatment can be either a physical, chemical, and/or biological processes, or in some cases a combination of these operations. The main purpose of wastewater treatment is to eliminate nutrients, solids, and organic compounds from effluents. Current wastewater treatment technologies are deemed ineffective in the complete removal of pollutants, particularly organic matter. In many cases, these organic compounds are resistant to conventional treatment methods, thus creating the necessity for tertiary treatment. Advanced oxidation process (AOP), constitutes as a promising treatment technology for the management of wastewater. AOPs are characterised by a common chemical feature, where they utilize the highly reactive hydroxyl radicals for achieving complete mineralization of the organic pollutants into carbon dioxide and water. This paper delineates advanced oxidation processes currently used for the remediation of water and wastewater. It also provides the cost estimation of installing and running an AOP system. The costs are separated into three categories: capital, operational, and operating & maintenance.

The life cycle of a mineral deposit: a teacher's guide for hands-on mineral education activities

USGS Publications Warehouse

Frank, Dave; Galloway, John; Assmus, Ken

2005-01-01

This teacher's guide defines what a mineral deposit is and how a mineral deposit is identified and measured, how the mineral resources are extracted, and how the mining site is reclaimed; how minerals and mineral resources are processed; and how we use mineral resources in our every day lives. Included are 10 activitybased learning exercises that educate students on basic geologic concepts; the processes of finding, identifying, and extracting the resources from a mineral deposit; and the uses of minerals. The guide is intended for K through 12 Earth science teachers and students and is designed to meet the National Science Content Standards as defined by the National Research Council (1996). To assist in the understanding of some of the geology and mineral terms, see the Glossary (appendix 1) and Minerals and Their Uses (appendix 2). The process of finding or exploring for a mineral deposit, extracting or mining the resource, recovering the resource, also known as beneficiation, and reclaiming the land mined can be described as the “life cycle” of a mineral deposit. The complete process is time consuming and expensive, requiring the use of modern technology and equipment, and may take many years to complete. Sometimes one entity or company completes the entire process from discovery to reclamation, but often it requires multiple groups with specialized experience working together. Mineral deposits are the source of many important commodities, such as copper and gold, used by our society, but it is important to realize that mineral deposits are a nonrenewable resource. Once mined, they are exhausted, and another source must be found. New mineral deposits are being continuously created by the Earth but may take millions of years to form. Mineral deposits differ from renewable resources, such as agricultural and timber products, which may be replenished within a few months to several years.

Portable Raman monitoring of modern cleaning and consolidation operations of artworks on mineral supports.

PubMed

Martínez-Arkarazo, I; Sarmiento, A; Maguregui, M; Castro, K; Madariaga, J M

2010-08-01

Any restoration performed on cultural heritage artworks must guarantee a low impact on the treated surfaces. Although completely risk-free methods do not exist, the use of tailor-made procedures and the continuous monitoring by portable instrumentation is surely one of the best approaches to conduct a modern restoration process. In this work, a portable Raman monitoring, combined sometimes with spectroscopic techniques providing the elemental composition, is the key analysis technique in the three-step restoration protocol proposed: (a) in situ analysis of the surface to be treated (original composition and degradation products/pollutants) and the cleaning agents used as extractants, (b) the thermodynamic study of the species involved in the treatment in order to design a suitable restoration method and (c) application and monitoring of the treatment. Two cleaning operations based on new technologies were studied and applied to two artworks on mineral supports: a wall painting affected by nitrate impact, and a black crusted stone (chalk) altarpiece. Raman bands of nitrate and gypsum, respectively, decreased after the step-by-step operations in each case, which helped restorers to decide when the treatment was concluded, thus avoiding any further damage to the treated surface of the artworks.

Reducing the chlorine dioxide demand in final disinfection of drinking water treatment plants using activated carbon.

PubMed

Sorlini, Sabrina; Biasibetti, Michela; Collivignarelli, Maria Cristina; Crotti, Barbara Marianna

2015-01-01

Chlorine dioxide is one of the most widely employed chemicals in the disinfection process of a drinking water treatment plant (DWTP). The aim of this work was to evaluate the influence of the adsorption process with granular activated carbon (GAC) on the chlorine dioxide consumption in final oxidation/disinfection. A first series of tests was performed at the laboratory scale employing water samples collected at the outlet of the DWTP sand filter of Cremona (Italy). The adsorption process in batch conditions with seven different types of GAC was studied. A second series of tests was performed on water samples collected at the outlet of four GAC columns installed at the outlet of the DWTP sand filter. The results showed that the best chlorine dioxide demand (ClO2-D) reduction yields are equal to 60-80% and are achieved in the first 30 min after ClO2 addition, during the first 16 days of the column operation using a mineral, coal-based, mesoporous GAC. Therefore, this carbon removes organic compounds that are more rapidly reactive with ClO2. Moreover, a good correlation was found between the ClO2-D and UV absorbance at wavelength 254 nm using mineral carbons; therefore, the use of a mineral mesoporous GAC is an effective solution to control the high ClO2-D in the disinfection stage of a DWTP.

Electroflotation

NASA Astrophysics Data System (ADS)

Chen, Xueming; Chen, Guohua

Electroflotation (EF) is the flotation using electrolytically generated bubbles of hydrogen and oxygen for separating suspended substances from aqueous phases. This process was first proposed by Elmore in 1905 for flotation of valuable minerals from ores. Compared with the conventional dissolved air flotation (DAF), EF has many advantages, including high flotation efficiency, compact units, easy operation, and less maintenance. Therefore, EF is an attractive alternative to DAF. This technique has been proven very effective in treating oily wastewater or oil-water emulsion, mining wastewater, groundwater, food processing wastewater, restaurant wastewater, industrial sewage, heavy metals containing effluent, and many other water and wastewaters.

Antibiotics mineralization by electrochemical and UV-based hybrid processes: evaluation of the synergistic effect.

PubMed

Wohlmuth da Silva, Salatiel; Arenhart Heberle, Alan Nelson; Pereira Santos, Alexia; Siqueira Rodrigues, Marco Antônio; Pérez-Herranz, Valentín; Moura Bernardes, Andréa

2018-05-29

Antibiotics are not efficiently removed in conventional wastewater treatments. In fact, different advanced oxidation process (AOPs), including ozone, peroxide, UV radiation, among others, are being investigated in the elimination of microcontaminants. Most of AOPs proved to be efficient on the degradation of antibiotics, but the mineralization is on the one hand not evaluated or on the other hand not high. At this work, the UV-based hybrid process, namely Photo-assisted electrochemical oxidation (PEO), was applied, aiming the mineralization of microcontaminants such as the antibiotics Amoxicillin (AMX), Norfloxacin (NOR) and Azithromycin (AZI). The influence of the individual contributions of electrochemical oxidation (EO) and the UV-base processes on the hybrid process (PEO) was analysed. Results showed that AMX and NOR presented higher mineralization rate under direct photolysis than AZI due to the high absorption of UV radiation. For the EO processes, a low mineralization was found for all antibiotics, what was associated to a mass-transport limitation related to the low concentration of contaminants (200 µg/L). Besides that, an increase in mineralization was found, when heterogeneous photocatalysis and EO are compared, due to the influence of UV radiation, which overcomes the mass-transport limitations. Although the UV-based processes control the reaction pathway that leads to mineralization, the best results to mineralize the antibiotics were achieved by PEO hybrid process. This can be explained by the synergistic effect of the processes that constitute them. A higher mineralization was achieved, which is an important and useful finding to avoid the discharge of microcontaminants in the environment.

Flexible recycling with Boliden technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hedlund, L.

There is today a long and well-documented experience of the use of Boliden ``Kaldo`` technology for treatment of various feed materials. The process is in commercial operation in the Boliden Mineral`s Roennskaer plant in Sweden for treatment of copper scraps and lead concentrates (in campaigns). This plant was built in 1976 for treatment of lead dusts from the copper plant but later modified to take other raw materials. Boliden`s Kaldo technology has been in operation since 1991 for treatment of low-grade copper scraps in Enirisorse`s plant in Porto Marghera (Venice), Italy. The plant is producing 25,000 tons of blister coppermore » per year. The Kaldo furnace is a high-intensity smelting unit, where several successive treatment steps can be done in the same vessel. The furnace can be totally enclosed to protect the working environment, and the small off-gas volume can easily be dedusted. Input materials can vary over a very wide range, the products will be a dump slag with low (0,5%) copper and lead contents and black copper or blister copper. The dust from the process can be used for zinc production. A new development is autogenous smelting of scrap in a Pierce-Smith converter, implemented at Compagnie Generale d`Electrolyse du Palais in France.« less

30 CFR 90.210 - Respirable dust samples; report to operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-COAL MINERS WHO HAVE EVIDENCE OF THE DEVELOPMENT OF PNEUMOCONIOSIS Sampling Procedures § 90.210 Respirable dust samples; report to operator. (a) The Secretary shall... for voiding any samples; and, (7) The Social Security Number of the part 90 miner. (b) Upon receipt...

30 CFR 250.103 - Where can I find more information about the requirements in this part?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements in this part? 250.103 Section 250.103 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF General... part? MMS may issue Notices to Lessees and Operators (NTLs) that clarify, supplement, or provide more...

30 CFR 210.101 - Who must submit production reports?

Code of Federal Regulations, 2010 CFR

2010-07-01

... MANAGEMENT FORMS AND REPORTS Production Reports-Oil and Gas § 210.101 Who must submit production reports? (a... operator number. To obtain an operator number, refer to the MMS Minerals Production Reporter Handbook for... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Who must submit production reports? 210.101...

30 CFR 250.133 - Will MMS reimburse me for my expenses related to inspections?

Code of Federal Regulations, 2010 CFR

2010-07-01

... to inspections? 250.133 Section 250.133 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF General Inspection of Operations § 250.133 Will MMS reimburse me for my expenses related to inspections? Upon request...

76 FR 79705 - Information Collection Activities: Operations in the Outer Continental Shelf for Minerals Other...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-22

.... BSEE-2011-0005; OMB Control Number 1014-NEW] Information Collection Activities: Operations in the Outer Continental Shelf for Minerals Other than Oil, Gas, and Sulphur; Submitted for Office of Management and Budget... Office of Management and Budget (OMB) for review and approval. The information collection request (ICR...

77 FR 57581 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-18

... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region AGENCY: Bureau of Ocean Energy Management (BOEM), Interior. ACTION: Notice of the availability of environmental...

77 FR 34405 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-11

... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region AGENCY: Bureau of Ocean Energy Management (BOEM), Interior. ACTION: Notice of the availability of environmental...

77 FR 74213 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-13

... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region AGENCY: Bureau of Ocean Energy Management (BOEM), Interior. ACTION: Notice of the availability of environmental...

77 FR 18263 - Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-27

... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management Environmental Documents Prepared for Proposed Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer Continental Shelf (OCS) Region AGENCY: Bureau of Ocean Energy Management, Interior. ACTION: Notice of the availability of Environmental...

30 CFR 250.455 - What are the general requirements for a drilling fluid program?

Code of Federal Regulations, 2010 CFR

2010-07-01

... drilling fluid program? 250.455 Section 250.455 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.455 What are the general requirements for a...

30 CFR 250.462 - What are the requirements for well-control drills?

Code of Federal Regulations, 2010 CFR

2010-07-01

... drills? 250.462 Section 250.462 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Other Drilling Requirements § 250.462 What are the requirements for well-control drills? You must...

30 CFR 62.160 - Hearing protectors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.160 Hearing protectors. (a) A mine operator must provide a hearing protector to a miner whose noise exposure equals or exceeds the action level under § 62.120 of this part. In addition, the mine operator must: (1) Train the miner in accordance with § 62.180 of this...

30 CFR 250.259 - What sulphur operations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What sulphur operations information must accompany the DPP or DOCD? 250.259 Section 250.259 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT... OUTER CONTINENTAL SHELF Plans and Information Contents of Development and Production Plans (dpp) and...

30 CFR 550.259 - What sulphur operations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false What sulphur operations information must accompany the DPP or DOCD? 550.259 Section 550.259 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT... toxic or thermal impacts on the environment caused by the discharge of bleedwater. (b) Subsidence. An...

30 CFR 550.259 - What sulphur operations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false What sulphur operations information must accompany the DPP or DOCD? 550.259 Section 550.259 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT... toxic or thermal impacts on the environment caused by the discharge of bleedwater. (b) Subsidence. An...

30 CFR 56.19107 - Precautions for work in compartment affected by hoisting operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Precautions for work in compartment affected by hoisting operation. 56.19107 Section 56.19107 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND...

30 CFR 57.19107 - Precautions for work in compartment affected by hoisting operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Precautions for work in compartment affected by hoisting operation. 57.19107 Section 57.19107 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL...

30 CFR 206.264 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false In-situ and surface gasification and... THE INTERIOR MINERALS REVENUE MANAGEMENT PRODUCT VALUATION Federal Coal § 206.264 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in-situ or...

30 CFR 206.463 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false In-situ and surface gasification and... THE INTERIOR MINERALS REVENUE MANAGEMENT PRODUCT VALUATION Indian Coal § 206.463 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in-situ or...

30 CFR 210.01 - What is the purpose of this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... identifies information collections required by the Minerals Management Service (MMS), Minerals Revenue Management (MRM), in the normal course of operations. This information is submitted by various parties... Federal and Indian minerals revenue management. Information collected regarding production, royalties, and...

Degradation of reactive orange 4 dye using hydrodynamic cavitation based hybrid techniques.

PubMed

Gore, Mohan M; Saharan, Virendra Kumar; Pinjari, Dipak V; Chavan, Prakash V; Pandit, Aniruddha B

2014-05-01

In the present work, degradation of reactive orange 4 dye (RO4) has been investigated using hydrodynamic cavitation (HC) and in combination with other AOP's. In the hybrid techniques, combination of hydrodynamic cavitation and other oxidizing agents such as H2O2 and ozone have been used to get the enhanced degradation efficiency through HC device. The hydrodynamic cavitation was first optimized in terms of different operating parameters such as operating inlet pressure, cavitation number and pH of the operating medium to get the maximum degradation of RO4. Following the optimization of HC parameters, the degradation of RO4 was carried out using the combination of HC with H2O2 and ozone. It has been found that the efficiency of the HC can be improved significantly by combining it with H2O2 and ozone. The mineralization rate of RO4 increases considerably with 14.67% mineralization taking place using HC alone increases to 31.90% by combining it with H2O2 and further increases to 76.25% through the combination of HC and ozone. The synergetic coefficient of greater than one for the hybrid processes of HC+H2O2 and HC+Ozone has suggested that the combination of HC with other oxidizing agents is better than the individual processes for the degradation of dye effluent containing RO4. The combination of HC with ozone proves to be the most energy efficient method for the degradation of RO4 as compared to HC alone and the hybrid process of HC and H2O2. Copyright © 2013 Elsevier B.V. All rights reserved.

Tribocharging Lunar Soil for Electrostatic Beneficiation

NASA Technical Reports Server (NTRS)

2008-01-01

Future human lunar habitation requires using in situ materials for both structural components and oxygen production. Lunar bases must be constructed from thermal-and radiation-shielding materials that will provide significant protection from the harmful cosmic energy which normally bombards the lunar surface. In addition, shipping oxygen from Earth is weight-prohibitive, and therefore investigating the production of breathable oxygen from oxidized mineral components is a major ongoing NASA research initiative. Lunar regolith may meet the needs for both structural protection and oxygen production. Already a number of oxygen production technologies are being tested, and full-scale bricks made of lunar simulant have been sintered. The beneficiation, or separation, of lunar minerals into a refined industrial feedstock could make production processes more efficient, requiring less energy to operate and maintain and producing higher-performance end products. The method of electrostatic beneficiation used in this research charges mineral powders (lunar simulant) by contact with materials of a different composition. The simulant acquires either a positive or negative charge depending upon its composition relative to the charging material.

Trace element diffusion in minerals: the role of multiple diffusion mechanisms operating simultaneously

NASA Astrophysics Data System (ADS)

Dohmen, R.; Marschall, H.; Wiedenbeck, M.; Polednia, J.; Chakraborty, S.

2016-12-01

Diffusion of trace elements, often with ionic charge that differs from those of ions in the regular structural sites of a mineral, controls a number of important processes in rocks, such as: (i) Closure of radiogenic isotopic systems, (e.g. Pb diffusion in rutile; REE diffusion in garnet); (ii) Closure of trace element thermometers (e.g., Zr in rutile, Mg in plagioclase, Al in olivine); (iii) Closure of element exchange between melt inclusions and host minerals (e.g., H, REE in olivine). In addition, preserved trace element zoning profiles in minerals can be used for diffusion chronometry (e.g. Nb in rutile, Mg in plagioclase). However, experimentally determined diffusion coefficients of these trace elements are in many cases controversial (e.g., REE in olivine: [1] vs. [2]; Mg in plagioclase: [3] vs. [4]). We have carried out experiments to study the diffusion behavior in olivine, rutile, and plagioclase, and are able to show that two mechanisms of diffusion, differing in rates by up to four orders of magnitude, may operate simultaneously in a given crystal. The two mechanisms result in complex diffusion profile shapes. As a general rule, the incorporation of heterovalent substituting elements in relatively high concentrations is necessary to activate two diffusion mechanisms. This behavior is produced by the control of these elements on the point defect chemistry of a mineral - these impurities become a majority point defect when a threshold concentration limit is exceeded. In certain cases, e.g., for Li in olivine, the trace element can also be incorporated in different sites, resulting in interaction of the different species with other point defects (vacancies) during diffusion. Thus, depending on the diffusion couple used in the experiment, the associated concentration gradients within the mineral, and the analytical techniques used to measure the diffusion profile, only one diffusion mechanism may be activated or detected. These studies allow us to explain some of the differing results noted above and such considerations need to be taken into account when modelling diffusion in natural systems. [1] Cherniak 2010, Am Mineral 95:362-368; [2] Spandler and O'Neill 2010, Contrib Mineral Petrol 159:791-818; [3] Faak et al. 2013 Geochim Cosmochim Acta 123:195-217; [4] Van Orman et al. 2014 Earth Planet Sci Lett 385:79-88

Urban net-zero water treatment and mineralization: experiments, modeling and design.

PubMed

Englehardt, James D; Wu, Tingting; Tchobanoglous, George

2013-09-01

Water and wastewater treatment and conveyance account for approximately 4% of US electric consumption, with 80% used for conveyance. Net zero water (NZW) buildings would alleviate demands for a portion of this energy, for water, and for the treatment of drinking water for pesticides and toxic chemical releases in source water. However, domestic wastewater contains nitrogen loads much greater than urban/suburban ecosystems can typically absorb. The purpose of this work was to identify a first design of a denitrifying urban NZW treatment process, operating at ambient temperature and pressure and circum-neutral pH, and providing mineralization of pharmaceuticals (not easily regulated in terms of environmental half-life), based on laboratory tests and mass balance and kinetic modeling. The proposed treatment process is comprised of membrane bioreactor, iron-mediated aeration (IMA, reported previously), vacuum ultrafiltration, and peroxone advanced oxidation, with minor rainwater make-up and H2O2 disinfection residual. Similar to biological systems, minerals accumulate subject to precipitative removal by IMA, salt-free treatment, and minor dilution. Based on laboratory and modeling results, the system can produce potable water with moderate mineral content from commingled domestic wastewater and 10-20% rainwater make-up, under ambient conditions at individual buildings, while denitrifying and reducing chemical oxygen demand to below detection (<3 mg/L). While economics appear competitive, further development and study of steady-state concentrations and sludge management options are needed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Potential aquifer vulnerability in regions down-gradient from uranium in situ recovery (ISR) sites.

PubMed

Saunders, James A; Pivetz, Bruce E; Voorhies, Nathan; Wilkin, Richard T

2016-12-01

Sandstone-hosted roll-front uranium ore deposits originate when U(VI) dissolved in groundwater is reduced and precipitated as insoluble U(IV) minerals. Groundwater redox geochemistry, aqueous complexation, and solute migration are important in leaching uranium from source rocks and transporting it in low concentrations to a chemical redox interface where it is deposited in an ore zone typically containing the uranium minerals uraninite, pitchblende, and/or coffinite; various iron sulfides; native selenium; clays; and calcite. In situ recovery (ISR) of uranium ores is a process of contacting the uranium mineral deposit with leaching and oxidizing (lixiviant) fluids via injection of the lixiviant into wells drilled into the subsurface aquifer that hosts uranium ore, while other extraction wells pump the dissolved uranium after dissolution of the uranium minerals. Environmental concerns during and after ISR include water quality degradation from: 1) potential excursions of leaching solutions away from the injection zone into down-gradient, underlying, or overlying aquifers; 2) potential migration of uranium and its decay products (e.g., Ra, Rn, Pb); and, 3) potential mobilization and migration of redox-sensitive trace metals (e.g., Fe, Mn, Mo, Se, V), metalloids (e.g., As), and anions (e.g., sulfate). This review describes the geochemical processes that control roll-front uranium transport and fate in groundwater systems, identifies potential aquifer vulnerabilities to ISR operations, identifies data gaps in mitigating these vulnerabilities, and discusses the hydrogeological characterization involved in developing a monitoring program. Published by Elsevier Ltd.

Chromium-removal processes during groundwater remediation by a zerovalent iron permeable reactive barrier.

PubMed

Wilkin, Richard T; Su, Chunming; Ford, Robert G; Paul, Cynthia J

2005-06-15

Solid-phase associations of chromium were examined in core materials collected from a full-scale, zerovalent iron permeable reactive barrier (PRB) at the U.S. Coast Guard Support Center located near Elizabeth City, NC. The PRB was installed in 1996 to treat groundwater contaminated with hexavalent chromium. After eight years of operation, the PRB remains effective at reducing concentrations of Cr from average values >1500 microg L(-1) in groundwater hydraulically upgradient of the PRB to values <1 microg L(-1) in groundwater within and hydraulically downgradient of the PRB. Chromium removal from groundwater occurs at the leading edge of the PRB and also within the aquifer immediately upgradient of the PRB. These regions also witness the greatest amount of secondary mineral formation due to steep geochemical gradients that result from the corrosion of zerovalent iron. X-ray absorption near-edge structure (XANES) spectroscopy indicated that chromium is predominantly in the trivalent oxidation state, confirming that reductive processes are responsible for Cr sequestration. XANES spectra and microscopy results suggest that Cr is, in part, associated with iron sulfide grains formed as a consequence of microbially mediated sulfate reduction in and around the PRB. Results of this study provide evidence that secondary iron-bearing mineral products may enhance the capacity of zerovalent iron systems to remediate Cr in groundwater, either through redox reactions at the mineral-water interface or by the release of Fe(II) to solution via mineral dissolution and/or metal corrosion.

29 CFR 2700.62 - Name of miner witness.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Name of miner witness. 2700.62 Section 2700.62 Labor... Hearings § 2700.62 Name of miner witness. A Judge shall not, until 2 days before a hearing, disclose or order a person to disclose to an operator or his agent the name of a miner who is expected by the Judge...

26 CFR 1.614-3 - Rules relating to separate operating mineral interests in the case of mines.

Code of Federal Regulations, 2010 CFR

2010-04-01

... method of mining the mineral, the location of the excavations or other workings in relation to the mineral deposit or deposits, and the topography of the area. The determination of the taxpayer as to the...

30 CFR 220.030 - Maintenance of records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR MINERALS REVENUE MANAGEMENT... cessation of NPSL operations by the lessee. All other documents, journals and records shall be maintained..., whichever comes later, except that nothing in these regulations shall limit the time of investigation or the...

Biodegradation performance of environmentally-friendly insulating oil

NASA Astrophysics Data System (ADS)

Yang, Jun; He, Yan; Cai, Shengwei; Chen, Cheng; Wen, Gang; Wang, Feipeng; Fan, Fan; Wan, Chunxiang; Wu, Liya; Liu, Ruitong

2018-02-01

In this paper, biodegradation performance of rapeseed insulating oil (RDB) and FR3 insulating oil (FR3) was studied by means of ready biodegradation method which was performed with Organization for Economic Co-operation and Development (OECD) 301B. For comparison, the biodegradation behaviour of 25# mineral insulating oil was also characterized with the same method. The testing results shown that the biodegradation degree of rapeseed insulating oil, FR3 insulating oil and 25# mineral insulating oil was 95.8%, 98.9% and 38.4% respectively. Following the “new chemical risk assessment guidelines” (HJ/T 154 - 2004), which illustrates the methods used to identify and assess the process safety hazards inherent. The guidelines can draw that the two vegetable insulating oils, i.e. rapeseed insulating oil and FR3 insulating oil are easily biodegradable. Therefore, the both can be classified as environmentally-friendly insulating oil. As expected, 25# mineral insulating oil is hardly biodegradable. The main reason is that 25# mineral insulating oil consists of isoalkanes, cyclanes and a few arenes, which has few unsaturated bonds. Biodegradation of rapeseed insulating oil and FR3 insulating oil also remain some difference. Biodegradation mechanism of vegetable insulating oil was revealed from the perspective of hydrolysis kinetics.

Assessment of Hg contamination and exposure to miners and schoolchildren at a small-scale gold mining and recovery operation in Thailand.

PubMed

Umbangtalad, S; Parkpian, P; Visvanathan, C; Delaune, R D; Jugsujinda, A

2007-12-01

Gold extracted by Hg-amalgamation process, which can cause both health and environmental problems, is widespread in South East Asia including Myanmar, Laos, Cambodia, and Thailand. Small-scale gold mining operations have been carried out since the year 2000 in Phanom Pha District, Phichit Province, Thailand. Since no data is available for evaluating Hg exposure, an investigation of mercury (Hg) contamination and exposure assessment was carried out at this mine site. Environmental monitoring illustrated the total Hg in water was as high as 4 microg/l while Hg in sediment ranged between 102 to 325 microg/kg dry weight. Both Hg deposition from the air (1.28 microg/100 cm(2)/day) and concentration in surface soil (20,960 microg/kg dry weight) were elevated in the area of amalgamation. The potential of Hg exposure to miners as well as to schoolchildren was assessed. The concentrations of Hg in urine of 79 miners who were directly (group I) or indirectly (group II) involved in the gold recovery operation were 32.02 and 20.04 microg/g creatinine, respectively, which did not exceed regulatory limits (35 microg/g creatinine). Hair Hg levels in both groups (group I and group II) also were not significantly higher than the non-exposed group. In terms of risk factors, gender and nature of food preparation and consumption were the two significant variables influencing the concentration of Hg in urine of miners (P < 0.05). A hazard quotient (HQ) was estimated based on the inorganic Hg exposure of individual miners. The HQ values of group I were in a range 16 to 218 times higher than the safety level set as 1. By comparison the group II HQ index was very low (0.03-0.39). The miners in group I who worked and ate food from this area experienced potentially high exposure to Hg associated with the mining process. In a second Hg exposure assessment, a group of 59 schoolchildren who attended an elementary school near the gold mine site was evaluated for Hg exposure. A slightly higher Hg urine concentration was detected in group I and group II (involved and not involved in gold recovery) at average levels of 15.82 and 9.95 microg/g creatinine, respectively. The average Hg values for both groups were below the established levels indicating no risk from Hg intake. Average Hg hair level in all schoolchildren (0.93 microg/g) was not significantly higher than reference group. There were two variables (gender and personal hygiene) which affected the concentration of Hg in urine of schoolchildren (P < 0.05). The result (HQ) also suggested that schoolchildren were not at risk (< 1). Schoolchildren involved in gold mining activities showed some indirect exposure to Hg from the adults working in mining area.

Mineral-organic interfacial processes: potential roles in the origins of life.

PubMed

Cleaves, H James; Michalkova Scott, Andrea; Hill, Frances C; Leszczynski, Jerzy; Sahai, Nita; Hazen, Robert

2012-08-21

Life is believed to have originated on Earth ∼4.4-3.5 Ga ago, via processes in which organic compounds supplied by the environment self-organized, in some geochemical environmental niches, into systems capable of replication with hereditary mutation. This process is generally supposed to have occurred in an aqueous environment and, likely, in the presence of minerals. Mineral surfaces present rich opportunities for heterogeneous catalysis and concentration which may have significantly altered and directed the process of prebiotic organic complexification leading to life. We review here general concepts in prebiotic mineral-organic interfacial processes, as well as recent advances in the study of mineral surface-organic interactions of potential relevance to understanding the origin of life.

State summaries: Oklahoma

USGS Publications Warehouse

Krukowski, S.T.

2006-01-01

In 2005, Oklahoma mines produced both industrial minerals and coal. No metals were mined in the state. Based on value, leading industrial minerals include crushed stone followed by cement, construction sand and gravel, industrial sand and gravel, iodine and gypsum. The Oklahoma Department of Mines (ODOM) reported that more than 343 mine operators produced nonfuel minerals from 405 mines in the state. However, 530 mining permitted sites were on file. The Oklahoma Miner Training Institute (OMTI) held 239 classes for 33,768 classroom hours of instruction, in which 84 coal miners and 4,587 metal/nonmetal miners were trained.

30 CFR 227.401 - What are a State's responsibilities if it processes production reports or royalty reports?

Code of Federal Regulations, 2010 CFR

2010-07-01

... and Reports, the MMS Minerals Production Reporter Handbook, any interagency memorandum of... processes production reports or royalty reports? 227.401 Section 227.401 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR MINERALS REVENUE MANAGEMENT DELEGATION TO STATES States...

30 CFR 581.32 - Waiver, suspension, or reduction of rental, minimum royalty, or production royalty.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Waiver, suspension, or reduction of rental, minimum royalty, or production royalty. 581.32 Section 581.32 Mineral Resources BUREAU OF OCEAN ENERGY... operator(s) if applicable. The application shall either: (1)(i) Show the location and extent of all mining...

30 CFR 581.32 - Waiver, suspension, or reduction of rental, minimum royalty, or production royalty.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Waiver, suspension, or reduction of rental, minimum royalty, or production royalty. 581.32 Section 581.32 Mineral Resources BUREAU OF OCEAN ENERGY... operator(s) if applicable. The application shall either: (1)(i) Show the location and extent of all mining...

30 CFR 581.32 - Waiver, suspension, or reduction of rental, minimum royalty, or production royalty.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Waiver, suspension, or reduction of rental, minimum royalty, or production royalty. 581.32 Section 581.32 Mineral Resources BUREAU OF OCEAN ENERGY... operator(s) if applicable. The application shall either: (1)(i) Show the location and extent of all mining...

26 CFR 1.614-3 - Rules relating to separate operating mineral interests in the case of mines.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 7 2011-04-01 2009-04-01 true Rules relating to separate operating mineral interests in the case of mines. 1.614-3 Section 1.614-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Natural Resources § 1...

30 CFR 250.445 - What are the requirements for kelly valves, inside BOPs, and drill-string safety valves?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., inside BOPs, and drill-string safety valves? 250.445 Section 250.445 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.445 What...

30 CFR 250.251 - If I propose activities in the Alaska OCS Region, what planning information must accompany the DPP?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Region, what planning information must accompany the DPP? 250.251 Section 250.251 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE... Development Operations Coordination Documents (docd) § 250.251 If I propose activities in the Alaska OCS...

Hydrologic and water quality effects of thinning Loblolly Pine

Treesearch

Johnny M. Grace; R. W. Skaggs; G. M. Chescheir

2006-01-01

Forest operations such as harvesting, thinning, and site preparation can affect the hydrologic behavior of watersheds on poorly drained soils. The influence of these operations conducted on organic soil sites can be more pronounced than on mineral soil sites due to the differences in bulk density and soil moisture relationships that exist between mineral and organic...

30 CFR 250.520 - When do I have to perform a casing diagnostic test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... test? 250.520 Section 250.520 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations Casing Pressure Management § 250.520 When do I have to perform a casing diagnostic test? (a) You...

30 CFR 582.22 - Delineation Plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Delineation Plan. 582.22 Section 582.22 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... minerals, and generate other information needed for the development of a comprehensive Testing or Mining...

30 CFR 582.22 - Delineation Plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Delineation Plan. 582.22 Section 582.22 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... minerals, and generate other information needed for the development of a comprehensive Testing or Mining...

30 CFR 582.22 - Delineation Plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Delineation Plan. 582.22 Section 582.22 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... minerals, and generate other information needed for the development of a comprehensive Testing or Mining...

30 CFR 282.50 - Appeals.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Appeals. 282.50 Section 282.50 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... for instructions on how to appeal any order or decision that we issue under this part. [65 FR 3857...

30 CFR 48.6 - Experienced miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (b) Experienced miners must complete the training prescribed in this section before beginning work... to work environment. The course shall include a visit and tour of the mine. The methods of mining... responsibilities of such supervisors and miners' representatives; and an introduction to the operator's rules and...

30 CFR 62.170 - Audiometric testing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... audiometric testing of the miner's hearing sensitivity for the purpose of establishing a valid baseline... the miner's hearing sensitivity as the baseline audiogram if it meets the audiometric testing... the testing. (2) The mine operator must notify the miner to avoid high levels of noise for at least 14...

30 CFR 62.170 - Audiometric testing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... audiometric testing of the miner's hearing sensitivity for the purpose of establishing a valid baseline... the miner's hearing sensitivity as the baseline audiogram if it meets the audiometric testing... the testing. (2) The mine operator must notify the miner to avoid high levels of noise for at least 14...

30 CFR 62.170 - Audiometric testing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... audiometric testing of the miner's hearing sensitivity for the purpose of establishing a valid baseline... the miner's hearing sensitivity as the baseline audiogram if it meets the audiometric testing... the testing. (2) The mine operator must notify the miner to avoid high levels of noise for at least 14...

30 CFR 62.170 - Audiometric testing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... audiometric testing of the miner's hearing sensitivity for the purpose of establishing a valid baseline... the miner's hearing sensitivity as the baseline audiogram if it meets the audiometric testing... the testing. (2) The mine operator must notify the miner to avoid high levels of noise for at least 14...

30 CFR 62.170 - Audiometric testing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... audiometric testing of the miner's hearing sensitivity for the purpose of establishing a valid baseline... the miner's hearing sensitivity as the baseline audiogram if it meets the audiometric testing... the testing. (2) The mine operator must notify the miner to avoid high levels of noise for at least 14...

Application of fuzzy logic and fuzzy AHP to mineral prospectivity mapping of porphyry and hydrothermal vein copper deposits in the Dananhu-Tousuquan island arc, Xinjiang, NW China

NASA Astrophysics Data System (ADS)

Zhang, Nannan; Zhou, Kefa; Du, Xishihui

2017-04-01

Mineral prospectivity mapping (MPM) is a multi-step process that ranks promising target areas for further exploration. Fuzzy logic and fuzzy analytical hierarchy process (AHP) are knowledge-driven MPM approaches. In this study, both approaches were used for data processing, based on which MPM was performed for porphyry and hydrothermal vein copper deposits in the Dananhu-Tousuquan island arc, Xinjiang. The results of the two methods were then compared. The two methods combined expert experience and the Studentized contrast (S(C)) values of the weights-of-evidence approach to calculate the weights of 15 layers, and these layers were then integrated by the gamma operator (γ). Through prediction-area (P-A) plot analysis, the optimal γ for fuzzy logic and fuzzy AHP was determined as 0.95 and 0.93, respectively. The thresholds corresponding to different levels of metallogenic probability were defined via concentration-area (C-A) fractal analysis. The prediction performances of the two methods were compared on this basis. The results showed that in MPM based on fuzzy logic, the area under the receiver operating characteristic (ROC) curve was 0.806 and 81.48% of the known deposits were predicted, whereas in MPM based on fuzzy AHP, the area under the ROC curve was 0.862 and 92.59% of the known deposits were predicted. Therefore, prediction based on fuzzy AHP is more accurate and can provide directions for future prospecting.

Recovery of magnetite from low grade banded magnetite quartzite (BMQ) ore

NASA Astrophysics Data System (ADS)

Tripathy, Alok; Bagchi, Subhankar; Rao, Danda Srinivas; Nayak, Bijaya Ketana; Rout, Prashanta Kumar; Biswal, Surendra Kumar

2018-04-01

There has been a steady increase of iron ore demand in the last few decades. This growing demand could be countered by use of low grade iron ore after beneficiation. Banded iron formations (BIF) are one of the resources of such low grade iron ores. Banded magnetite quartzite (BMQ) is one such BIF and a source of iron phase mineral in the form of magnetite. In the present study a low grade BMQ ore containing around 25.47% Fe was beneficiated for recovery of magnetite. XRD study shows that quartz, magnetite, hematite, and goethite are the major minerals phases present in the low grade BMQ sample. Unit operations such as crushing, scrubbing, grinding, and magnetic separations were used for recovering magnetite. Based on the large scale beneficiation studies the process flowsheet has been developed for enrichment of magnetite. It was found that with the help of developed process flowsheet it is possible to enrich Fe value up to 65.14% in the concentrate with a yield of 24.59%.

Review of the Scientific Understanding of Radioactive Waste at the U.S. DOE Hanford Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Reid A.; Buck, Edgar C.; Chun, Jaehun

This paper reviews the origin and chemical and rheological complexity of radioactive waste at the U.S. Department of Energy’s Hanford Site. The waste, stored in underground tanks, was generated via three distinct processes over decades of plutonium extraction operations. Although close records were kept of original waste disposition, tank-to-tank transfers and conditions that impede equilibrium complicate our understanding of the chemistry, phase composition, and rheology of the waste. Tank waste slurries comprise particles and aggregates from nano to micron scales, with varying densities, morphologies, heterogeneous compositions, and complicated responses to flow regimes and process conditions. Further, remnant or changing radiationmore » fields may affect the stability and rheology of the waste. These conditions pose challenges for transport through conduits or pipes to treatment plants for vitrification. Additionally, recalcitrant boehmite degrades glass quality and must be reduced prior to vitrification, but dissolves much more slowly than predicted given surface normalized rates. Existing empirical models based on ex situ experiments and observations lack true predictive capabilities. Recent advances in in situ microscopy, aberration corrected TEM, theoretical modeling across scales, and experimental methods for probing the physics and chemistry at mineral-fluid and mineral-mineral interfaces are being implemented to build robustly predictive physics-based models.« less

Understanding Contaminants Associated with Mineral Deposits

USGS Publications Warehouse

Verplanck, Philip L.

2008-01-01

Interdisciplinary studies by the U.S. Geological Survey (USGS) have resulted in substantial progress in understanding the processes that control *the release of metals and acidic water from inactive mines and mineralized areas, *the transport of metals and acidic water to streams, and *the fate and effect of metals and acidity on downstream ecosystems. The potential environmental effects associated with abandoned and inactive mines, resulting from the complex interaction of a variety of chemical and physical processes, is an area of study that is important to the USGS Mineral Resources Program. Understanding the processes contributing to the environmental effects of abandoned and inactive mines is also of interest to a wide range of stakeholders, including both those responsible for managing lands with historically mined areas and those responsible for anticipating environmental consequences of future mining operations. The recently completed (2007) USGS project entitled 'Process Studies of Contaminants Associated with Mineral Deposits' focused on abandoned and inactive mines and mineralized areas in the Rocky Mountains of Montana, Colorado, New Mexico, Utah, and Arizona, where there are thousands of abandoned mines. Results from these studies provide new information that advances our understanding of the physical and biogeochemical processes causing the mobilization, transport, reaction, and fate of potentially toxic elements (including aluminum, arsenic, cadmium, copper, iron, lead, and zinc) in mineralized near-surface systems and their effects on aquatic and riparian habitat. These interdisciplinary studies provide the basis for scientific decisionmaking and remedial action by local, State, and Federal agencies charged with minimizing the effects of potentially toxic elements on the environment. Current (2007) USGS research highlights the need to understand (1) the geologic sources of metals and acidity and the geochemical reactions that release them from their sources, (2) the pathways that facilitate transport from those sources, and (3) the processes that control the fate of the elements once released from the sources. Experts in the fields of economic geology, structural geology, mineralogy, geophysics, geochemistry, hydrology, ground-water modeling, microbiology, and toxicology came together for a series of studies that address these relationships on scales ranging from the microscopic to the watershed. This Circular presents results and highlights from the detailed, interdisciplinary studies that include investigations in both mining-affected areas and mineralized but unmined areas. The first section of the Circular describes laboratory and site-scale field investigations that primarily focus on mineralogic and biologic controls on the source and release of metals and acidity from mine-waste rock and hydrothermally altered areas. The second section describes a set of basin- to watershed-scale studies that not only investigate the source and release of metals and acidity but also the transport of these constituents away from the source areas. The third section is a summary of results from postremediation ecosystem monitoring. For more information on these and other project-related studies, please visit the project Web site at http://minerals.cr.usgs.gov/projects/contaminants/index.html. The Web site includes a complete bibliography and detailed descriptions of each interdisciplinary study.

Livers, guts and gills: mapping the decay profiles of soft tissues to understand authigenic mineral replacement.

NASA Astrophysics Data System (ADS)

Clements, Thomas; Purnell, Mark; Gabbott, Sarah

2016-04-01

The hard mineralised parts of organisms such as shells, teeth and bones dominate the fossil record. There are, however, sites around the world where soft-tissues are preserved often through rapid replacement of original tissue by rapidly-precipitating authigenic minerals. These exceptionally well-preserved soft-bodied fossils are much more informative about the anatomy, physiology, ecology and behaviour of ancient organisms as well as providing a more inclusive picture of ecosystems and evolution throughout geological time. However, despite the wealth of information that soft-bodied fossils can provide they must first be correctly interpreted as the processes of both decay and preservation act to modify the carcass from its in vivo condition. Decay leads to alteration of the appearance and topology of anatomy, and ultimately to loss. Preservation is selective with some anatomical features being more likely to be captured than others. These problems are especially germane to the interpretation of deep-time and/or enigmatic fossils where no modern analogue exist for comparative anatomical analysis. It is therefore of vital importance to understand the processes carcasses undergo during the fossilisation process, , in order to interpret the anatomical remains of fossils and thus extract true evolutionary presence or absence of anatomy from absence due to taphonomic biases. We have designed a series of novel experiments to investigate, in real time, how decay processes affect the fossilisation potential of soft-tissues - especially of internal anatomy. Our data allow us to unravel both the timing and sequence of anatomical decay of different organs. At the same time through measuring Eh and pH in selected organs we can predict when anatomical features will fall in to the window of authigenic mineralization and thus potentially become preserved. We can also place constraints on which minerals will operate to capture tissues. Our findings are applied to the fossil record allowing greater accuracy in reading the record of exceptionally preserved organisms.

30 CFR 582.24 - Mining Plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Mining Plan. 582.24 Section 582.24 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... § 582.24 Mining Plan. All OCS mineral development and production activities shall be conducted in...

30 CFR 582.24 - Mining Plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Mining Plan. 582.24 Section 582.24 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... § 582.24 Mining Plan. All OCS mineral development and production activities shall be conducted in...

30 CFR 582.24 - Mining Plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Mining Plan. 582.24 Section 582.24 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... § 582.24 Mining Plan. All OCS mineral development and production activities shall be conducted in...

30 CFR 90.100 - Respirable dust standard.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MANDATORY HEALTH STANDARDS-COAL MINERS WHO HAVE EVIDENCE OF THE DEVELOPMENT OF PNEUMOCONIOSIS Dust Standards, Rights of Part 90 Miners § 90.100 Respirable dust standard. After the twentieth calendar day following receipt of notification from MSHA that a Part 90 miner is employed at the mine, the operator shall...

30 CFR 227.200 - What are a State's general responsibilities if it accepts a delegation?

Code of Federal Regulations, 2010 CFR

2010-07-01

... it accepts a delegation? 227.200 Section 227.200 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR MINERALS REVENUE MANAGEMENT DELEGATION TO STATES States' Responsibilities to... delegation? For each delegated function you perform, you must: (a) Operate in compliance with all Federal...

36 CFR 5.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Prospecting, mining, and mineral leasing. 5.14 Section 5.14 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR COMMERCIAL AND PRIVATE OPERATIONS § 5.14 Prospecting, mining, and mineral leasing...

36 CFR 5.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Prospecting, mining, and mineral leasing. 5.14 Section 5.14 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR COMMERCIAL AND PRIVATE OPERATIONS § 5.14 Prospecting, mining, and mineral leasing...

36 CFR 5.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Prospecting, mining, and mineral leasing. 5.14 Section 5.14 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR COMMERCIAL AND PRIVATE OPERATIONS § 5.14 Prospecting, mining, and mineral leasing...

36 CFR 5.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Prospecting, mining, and mineral leasing. 5.14 Section 5.14 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR COMMERCIAL AND PRIVATE OPERATIONS § 5.14 Prospecting, mining, and mineral leasing...

30 CFR 250.253 - What lease stipulations information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What lease stipulations information must accompany the DPP or DOCD? 250.253 Section 250.253 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Information Contents of Development and Production Plans (dpp) and Development Operations Coordination...

30 CFR 250.262 - What administrative information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What administrative information must accompany the DPP or DOCD? 250.262 Section 250.262 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF... Information Contents of Development and Production Plans (dpp) and Development Operations Coordination...

30 CFR 250.254 - What mitigation measures information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What mitigation measures information must accompany the DPP or DOCD? 250.254 Section 250.254 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Information Contents of Development and Production Plans (dpp) and Development Operations Coordination...

30 CFR 250.255 - What decommissioning information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What decommissioning information must accompany the DPP or DOCD? 250.255 Section 250.255 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF... Information Contents of Development and Production Plans (dpp) and Development Operations Coordination...

ProteMiner-SSM: a web server for efficient analysis of similar protein tertiary substructures.

PubMed

Chang, Darby Tien-Hau; Chen, Chien-Yu; Chung, Wen-Chin; Oyang, Yen-Jen; Juan, Hsueh-Fen; Huang, Hsuan-Cheng

2004-07-01

Analysis of protein-ligand interactions is a fundamental issue in drug design. As the detailed and accurate analysis of protein-ligand interactions involves calculation of binding free energy based on thermodynamics and even quantum mechanics, which is highly expensive in terms of computing time, conformational and structural analysis of proteins and ligands has been widely employed as a screening process in computer-aided drug design. In this paper, a web server called ProteMiner-SSM designed for efficient analysis of similar protein tertiary substructures is presented. In one experiment reported in this paper, the web server has been exploited to obtain some clues about a biochemical hypothesis. The main distinction in the software design of the web server is the filtering process incorporated to expedite the analysis. The filtering process extracts the residues located in the caves of the protein tertiary structure for analysis and operates with O(nlogn) time complexity, where n is the number of residues in the protein. In comparison, the alpha-hull algorithm, which is a widely used algorithm in computer graphics for identifying those instances that are on the contour of a three-dimensional object, features O(n2) time complexity. Experimental results show that the filtering process presented in this paper is able to speed up the analysis by a factor ranging from 3.15 to 9.37 times. The ProteMiner-SSM web server can be found at http://proteminer.csie.ntu.edu.tw/. There is a mirror site at http://p4.sbl.bc.sinica.edu.tw/proteminer/.

Fluoride and apatite formation in vivo and in vitro.

PubMed

Aoba, Takaaki; Shimazu, Yoshihito; Taya, Yuji; Soeno, Yuuichi; Sato, Kaori; Miake, Yasuo

2003-01-01

In recent years, the biomineralization process has attracted much interest from academics and industries for potential technological application. The rule in biomineralization is to have a variety of interfaces and surfaces which can act as nucleators. The ultimate step in any biomineralization process, i.e. the deposition of mineral, must conform to the driving forces operating on the system. A new paradigm in the assessment of the driving force for biomineralization is that a variety of ions existing in the mineralizing milieu are not a bystander, but are instead an active player that directly regulates the precipitation process and nature of biogenic apatites. Thus, the most putative stoichiometric model of a biomineral is (Ca)(5-x)(Mg)q(Na)u(HPO4)v(CO3)w(PO4)(3-y)(OH,F)(1-z). Fluoride participates in many aspects of calcium phosphate formation in vivo and has enormous effects on its process and on the nature and properties of the final products. In the development of biogenic apatites, fluoride ion in the mineralizing media is supposed to accelerate the hydrolysis of acidic precursor(s) and increase the growth rates by augmenting the driving force for precipitation. Inhibitory activities of ions and molecules are related to their adsorption onto the apatite surfaces. From theoretical and practical points of view, it is of paramount importance to elucidate and predict the effect and outcome of fluoride (accelerator) and inhibitors of biological relevance, because of their use in combination for healthcare in dentistry and medicine, e.g. prevention of dental caries and calculus deposition and in the formulation of antiosteoporosis treatments.

The application of the electrodynamic separator in minerals beneficiation

NASA Astrophysics Data System (ADS)

Skowron, M.; Syrek, P.; Surowiak, A.

2017-05-01

The aim of presented paper is elaboration of methodology of upgrading natural minerals in example of chalcocite and bornite sample. The results were obtained by means of laboratory drum separator. This device operates in accordance to properties of materials, which in this case was electrical conductivity. The study contains the analysis of the forces occurring inside of electrodynamic separator chamber, that act on the particles of various electrical properties. Both, the potential and electric field strength distributions were calculated, with set of separators setpoints. Theoretical analysis influenced on separator parameters, and hence impacted the empirical results too. Next, the authors conducted empirical research on chalcocite and bornite beneficiation by means of electrodynamic separation. The results of this process were shown graphically in form of upgrading curves of chalcocite considering elementary copper and lead.

Microbial mineralization of cis-dichloroethene and vinyl chloride as a component of natural attenuation of chloroethene contaminants under conditions identified in the field as anoxic

USGS Publications Warehouse

Bradley, Paul M.

2012-01-01

Chlororespiration is a key component of remediation at many chloroethene-contaminated sites. In some instances, limited accumulation of reductive dechlorination daughter products may suggest that natural attenuation is not adequate for site remediation. This conclusion is justified when evidence for parent compound (tetrachloroethene, PCE, or trichloroethene, TCE) degradation is lacking. For many chloroethene-contaminated shallow aquifer systems, however, non-conservative losses of the parent compounds are clear but the mass balance between parent compound attenuation and accumulation of reductive dechlorination daughter products is incomplete. Incomplete mass balance indicates a failure to account for important contaminant attenuation mechanisms, and is consistent with contaminant degradation to non-diagnostic mineralization products. An ongoing technical debate over the potential for mineralization of dichloroethene (DCE) and vinyl chloride (VC) to CO2 in the complete absence of diatomic oxygen has largely obscured the importance of microbial DCE/VC mineralization at dissolved oxygen (DO) concentrations below the current field standard (DO < 0.1-0.5 milligrams per liter) for nominally anoxic conditions. This study demonstrates that oxygen-based microbial mineralization of DCE and VC can be substantial under field conditions that are frequently characterized as "anoxic." Because mischaracterization of operant contaminant biodegradation processes can lead to expensive and ineffective remedial actions, a modified framework for assessing the potential importance of oxygen during chloroethene biodegradation was developed.

A new microcolumn flotation cell for determining the wettability and floatability of minerals.

PubMed

Ozkan, A; Yekeler, M

2003-05-15

Flotation is one of the most important physicochemical processes for mineral separations and other recovery operations. Flotation machines have been developed since the beginning of the 19th century and are still under intensive research and development. The cell we devised is a combination of the Canadian column flotation cell and the Partridge-Smith cell. The materials used for the construction of the new cell are cheap and use available laboratory accessories and aquarium materials. The cell functions well in terms of its scale, control, and sample requirement. It can be used both in the laboratory for research and in classrooms for demonstrations of experiments. Some of the data obtained by the flotation method using this cell are in good agreement with data measured independently on the same minerals by the contact angles method. The critical values of surface tension of wetting (gamma(c)) for talc, sulfur, and chemically treated surfaces of calcite and barite obtained by the contact angle measurements were 31, 26, 30.5, and 31.2 mN/m, respectively. On the other hand, the gamma(c) values of those minerals, obtained using our new designed flotation cell, were 30, 28, 31.4, and 34.5 mN/m, respectively. The measurements obtained in our experiment are also comparable to those previously published for the same minerals.

IMPROVING TACONITE PROCESSING PLANT EFFICIENCY BY COMPUTER SIMULATION, Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

William M. Bond; Salih Ersayin

2007-03-30

This project involved industrial scale testing of a mineral processing simulator to improve the efficiency of a taconite processing plant, namely the Minorca mine. The Concentrator Modeling Center at the Coleraine Minerals Research Laboratory, University of Minnesota Duluth, enhanced the capabilities of available software, Usim Pac, by developing mathematical models needed for accurate simulation of taconite plants. This project provided funding for this technology to prove itself in the industrial environment. As the first step, data representing existing plant conditions were collected by sampling and sample analysis. Data were then balanced and provided a basis for assessing the efficiency ofmore » individual devices and the plant, and also for performing simulations aimed at improving plant efficiency. Performance evaluation served as a guide in developing alternative process strategies for more efficient production. A large number of computer simulations were then performed to quantify the benefits and effects of implementing these alternative schemes. Modification of makeup ball size was selected as the most feasible option for the target performance improvement. This was combined with replacement of existing hydrocyclones with more efficient ones. After plant implementation of these modifications, plant sampling surveys were carried out to validate findings of the simulation-based study. Plant data showed very good agreement with the simulated data, confirming results of simulation. After the implementation of modifications in the plant, several upstream bottlenecks became visible. Despite these bottlenecks limiting full capacity, concentrator energy improvement of 7% was obtained. Further improvements in energy efficiency are expected in the near future. The success of this project demonstrated the feasibility of a simulation-based approach. Currently, the Center provides simulation-based service to all the iron ore mining companies operating in northern Minnesota, and future proposals are pending with non-taconite mineral processing applications.« less

Bone mineral decreases in the calcanei in men after arthroscopic shoulder surgery: a prospective study over 5 years.

PubMed

Elmlund, Anna O; Kartus, Jüri; Ejerhed, Lars

2016-12-01

It is well known that injuries and surgical procedures in the lower extremities affect bone mineral both in the injured limb and in the contralateral limb. The possible effect on bone mineral after upper extremity surgery is not well studied, and the aim of this study was to study the effect on bone mineral in the calcanei after arthroscopic shoulder surgery. Twenty-two men scheduled for arthroscopic shoulder surgery underwent bone mineral area (BMA) mass measurements in both calcanei using the Calscan DXL device prior to surgery and after 6, 18, 36 and 60 months. On every occasion, the Tegner activity score and EuroQoL 5-dimensions (EQ-5D) were assessed. During 5 years, there was a significant decrease in the BMA in both calcanei (p = 0.003). The Tegner activity score decreased from preinjury to the operation and did not increase significantly after the operation. The EQ-5D increased significantly after the operation. The bone mineral in the calcanei in men during the 5-year study period decreased more than the expected age-dependent decline after arthroscopic shoulder surgery. There was an increase in health-related quality of life as measured with the EQ-5D after arthroscopic Bankart reconstruction. Case-control study, Level III.

26 CFR 1.614-2 - Election to aggregate separate operating mineral interests under section 614(b) prior to its...

Code of Federal Regulations, 2011 CFR

2011-04-01

...) INCOME TAXES (CONTINUED) Natural Resources § 1.614-2 Election to aggregate separate operating mineral... various natural resources industries or in any one of the natural resources industries, such as coal, oil... mine, well, or other natural deposit were in the production stage. The term does not include royalty...

Evolution of ribozymes in the presence of a mineral surface

PubMed Central

Stephenson, James D.; Popović, Milena; Bristow, Thomas F.

2016-01-01

Mineral surfaces are often proposed as the sites of critical processes in the emergence of life. Clay minerals in particular are thought to play significant roles in the origin of life including polymerizing, concentrating, organizing, and protecting biopolymers. In these scenarios, the impact of minerals on biopolymer folding is expected to influence evolutionary processes. These processes include both the initial emergence of functional structures in the presence of the mineral and the subsequent transition away from the mineral-associated niche. The initial evolution of function depends upon the number and distribution of sequences capable of functioning in the presence of the mineral, and the transition to new environments depends upon the overlap between sequences that evolve on the mineral surface and sequences that can perform the same functions in the mineral's absence. To examine these processes, we evolved self-cleaving ribozymes in vitro in the presence or absence of Na-saturated montmorillonite clay mineral particles. Starting from a shared population of random sequences, RNA populations were evolved in parallel, along separate evolutionary trajectories. Comparative sequence analysis and activity assays show that the impact of this clay mineral on functional structure selection was minimal; it neither prevented common structures from emerging, nor did it promote the emergence of new structures. This suggests that montmorillonite does not improve RNA's ability to evolve functional structures; however, it also suggests that RNAs that do evolve in contact with montmorillonite retain the same structures in mineral-free environments, potentially facilitating an evolutionary transition away from a mineral-associated niche. PMID:27793980

Crossing disciplines and scales to understand the critical zone

USGS Publications Warehouse

Brantley, S.L.; Goldhaber, M.B.; Vala, Ragnarsdottir K.

2007-01-01

The Critical Zone (CZ) is the system of coupled chemical, biological, physical, and geological processes operating together to support life at the Earth's surface. While our understanding of this zone has increased over the last hundred years, further advance requires scientists to cross disciplines and scales to integrate understanding of processes in the CZ, ranging in scale from the mineral-water interface to the globe. Despite the extreme heterogeneities manifest in the CZ, patterns are observed at all scales. Explanations require the use of new computational and analytical tools, inventive interdisciplinary approaches, and growing networks of sites and people.

Review of the Scientific Understanding of Radioactive Waste at the U.S. DOE Hanford Site.

PubMed

Peterson, Reid A; Buck, Edgar C; Chun, Jaehun; Daniel, Richard C; Herting, Daniel L; Ilton, Eugene S; Lumetta, Gregg J; Clark, Sue B

2018-01-16

This Critical Review reviews the origin and chemical and rheological complexity of radioactive waste at the U.S. Department of Energy Hanford Site. The waste, stored in underground tanks, was generated via three distinct processes over decades of plutonium extraction operations. Although close records were kept of original waste disposition, tank-to-tank transfers and conditions that impede equilibrium complicate our understanding of the chemistry, phase composition, and rheology of the waste. Tank waste slurries comprise particles and aggregates from nano to micro scales, with varying densities, morphologies, heterogeneous compositions, and complicated responses to flow regimes and process conditions. Further, remnant or changing radiation fields may affect the stability and rheology of the waste. These conditions pose challenges for transport through conduits or pipes to treatment plants for vitrification. Additionally, recalcitrant boehmite degrades glass quality and the high aluminum content must be reduced prior to vitrification for the manufacture of waste glass of acceptable durability. However, caustic leaching indicates that boehmite dissolves much more slowly than predicted given surface normalized rates. Existing empirical models based on ex situ experiments and observations generally only describe material balances and have not effectively predicted process performance. Recent advances in the areas of in situ microscopy, aberration-corrected transmission electron microscopy, theoretical modeling across scales, and experimental methods for probing the physics and chemistry at mineral-fluid and mineral-mineral interfaces are being implemented to build robustly predictive physics-based models.

Complete removal of AHPS synthetic dye from water using new electro-fenton oxidation catalyzed by natural pyrite as heterogeneous catalyst.

PubMed

Labiadh, Lazhar; Oturan, Mehmet A; Panizza, Marco; Hamadi, Nawfel Ben; Ammar, Salah

2015-10-30

The mineralization of a new azo dye - the (4-amino-3-hydroxy-2-p-tolylazo-naphthalene-1-sulfonic acid) (AHPS) - has been studied by a novel electrochemical advanced oxidation process (EAOP), consisting in electro-Fenton (EF) oxidation, catalyzed by pyrite as the heterogeneous catalyst - the so-called 'pyrite-EF'. This solid pyrite used as heterogeneous catalyst instead of a soluble iron salt, is the catalyst the system needs for production of hydroxyl radicals. Experiments were performed in an undivided cell equipped with a BDD anode and a commercial carbon felt cathode to electrogenerate in situ H2O2 and regenerate ferrous ions as catalyst. The effects on operating parameters, such as applied current, pyrite concentration and initial dye content, were investigated. AHPS decay and mineralization efficiencies were monitored by HPLC analyses and TOC measurements, respectively. Experimental results showed that AHPS was quickly oxidized by hydroxyl radicals (OH) produced simultaneously both on BDD surface by water discharge and in solution bulk from electrochemically assisted Fenton's reaction with a pseudo-first-order reaction. AHPS solutions with 175 mg L(-1) (100 mg L(-1) initial TOC) content were then almost completely mineralized in 8h. Moreover, the results demonstrated that, under the same conditions, AHPS degradation by pyrite electro-Fenton process was more powerful than the conventional electro-Fenton process. Copyright © 2015 Elsevier B.V. All rights reserved.

The Ebola virus disease outbreak and the mineral sectors of Guinea, Liberia, and Sierra Leone

USGS Publications Warehouse

Bermúdez-Lugo, Omayra; Menzie, William D.

2015-01-01

In response to the uncertainty surrounding the status of mineral projects in Guinea, Liberia, and Sierra Leone, the National Minerals Information Center compiled information on the distribution of mines, mineral facilities, and mineral projects under development in the three countries. This fact sheet provides information on the role that the mineral sector plays in their respective economies, on the operating status of mining projects through yearend 2014, and on the coordinated actions by mining companies to support governments and international relief organizations in their efforts to contain the EVD outbreak.

Atmospheric Processing and Iron Mobilization of Ilmenite: Iron-Containing Ternary Oxide in Mineral Dust Aerosol.

PubMed

Hettiarachchi, Eshani; Hurab, Omar; Rubasinghege, Gayan

2018-02-08

Over the last several decades, iron has been identified as a limiting nutrient in about half of the world's oceans. Its most significant source is identified as deposited iron-containing mineral dust that has been processed during atmospheric transportation. The current work focuses on chemical and photochemical processing of iron-containing mineral dust particles in the presence of nitric acid, and an organic pollutant dimethyl sulfide under atmospherically relevant conditions. More importantly, ilmenite (FeTiO 3 ) is evaluated as a proxy for the iron-containing mineral dust. The presence of titanium in its lattice structure provides higher complexity to mimic mineral dust, yet it is simple enough to study reaction pathways and mechanisms. Here, spectroscopic methods are combined with dissolution measurements to investigate atmospheric processing of iron in mineral dust, with specific focus on particle mineralogy, particle size, and their environmental conditions (i.e., pH and solar flux). Our results indicate that the presence of titanium elemental composition enhances iron dissolution from mineral dust, at least by 2-fold comparison with its nontitanium-containing counterparts. The extent of iron dissolution and speciation is further influenced by the above factors. Thus, our work highlights these important, yet unconsidered, factors in the atmospheric processing of iron-containing mineral dust aerosol.

Mg- and K-bearing borates and associated evaporites at Eagle Borax spring, Death Valley, California: A spectroscopic exploration

USGS Publications Warehouse

Crowley, J.K.

1996-01-01

Efflorescent crusts at the Eagle Borax spring in Death Valley, California, contain an array of rare Mg and K borate minerals, several of which are only known from one or two other localities. The Mg- and/or K-bearing borates include aristarainite, hydroboracite, kaliborite, mcallisterite, pinnoite, rivadavite, and santite. Ulexite and probertite also occur in the area, although their distribution is different from that of the Mg and K borates. Other evaporite minerals in the spring vicinity include halite, thenardite, eugsterite, gypsum-anhydrite, hexahydrite, and bloedite. Whereas the first five of these minerals are found throughout Death Valley, the last two Mg sulfates are more restricted in occurrence and are indicative of Mg-enriched ground water. Mineral associations observed at the Eagle Borax spring, and at many other borate deposits worldwide, can be explained by the chemical fractionation of borate-precipitating waters during the course of evaporative concentration. The Mg sulfate and Mg borate minerals in the Eagle Borax efflorescent crusts point to the fractionation of Ca by the operation of a chemical divide involving Ca carbonate and Na-Ca borate precipitation in the subsurface sediments. At many other borate mining localities, the occurrence of ulexite in both Na borate (borax-kernite) and Ca borate (ulexite-colemanite) deposits similarly reflects ulexite's coprecipitation with Ca carbonate at an early concentration stage. Such ulexite may perhaps be converted to colemanite by later reaction with the coexisting Ca carbonate - the latter providing the additional Ca2+ ions needed for the conversion. Mg and Ca-Mg borates are the expected late-stage concentration products of waters forming ulexite-colemanite deposits and are therefore most likely to occur in the marginal zones or nearby mud facies of ulexite-colemanite orebodies. Under some circumstances, Mg and Ca-Mg borates might provide a useful prospecting guide for ulexite-colemanite deposits, although the high solubility of Mg borate minerals may prevent their formation in lacustrine settings and certainly inhibits their geologic preservation. The occurrence of Mg borates in borax-kernite deposits is also related to fractionation processes and points to the operation of an Mg borate chemical divide, characterized by Mg borate precipitation ahead of Mg carbonate. All of these considerations imply that Mg is a significant chemical component of many borate-depositing ground waters, even though Mg borate minerals may not be strongly evident in borate orebodies. The Eagle Borax spring borates and other evaporite minerals were studied using spectroscopic and X-ray powder diffraction methods, which were found to be highly complementary. Spectral reflectance measurements provide a sensitive means for detecting borates present in mixtures with other evaporites and can be used to screen samples rapidly for X-ray diffraction analysis. The apparently limited occurrence of Mg and K borate minerals compared to Ca and Na borates may stem partly from the inefficiency of X-ray diffraction methods for delineating the mineralogy of large and complex deposits. Spectral reflectance measurements can be made in the laboratory, in the field, on the mine face, and even remotely. Reflectance data should have an important role in studies of existing deposit mineralogy and related chemical fractionation processes, and perhaps in the discovery of new borate mineral resources.

30 CFR 285.613 - How will MMS process my SAP?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will MMS process my SAP? 285.613 Section 285.613 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE... Requirements Contents of the Site Assessment Plan § 285.613 How will MMS process my SAP? (a) The MMS will...

30 CFR 285.648 - How will MMS process my GAP?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will MMS process my GAP? 285.648 Section 285.648 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE... Requirements Contents of the General Activities Plan § 285.648 How will MMS process my GAP? (a) The MMS will...

Nanostructured ZnO-TiO2 thin film oxide as anode material in electrooxidation of organic pollutants. Application to the removal of dye Amido black 10B from water.

PubMed

El-Kacemi, Sana; Zazou, Hicham; Oturan, Nihal; Dietze, Matthias; Hamdani, Mohamed; Es-Souni, Mohammed; Oturan, Mehmet A

2017-01-01

Electrochemical oxidative degradation of diazo dye Amido black 10B (AB10B) as model pollutant in water has been studied using nanostructured ZnO-TiO 2 thin films deposited on graphite felt (GrF) substrate as anode. The influence of various operating parameters, namely the current intensity, the nature and concentration of catalyst, the nature of electrode materials (anode/cathode), and the adsorption of dye and ambient light were investigated. It was found that the oxidative degradation of AB10B followed pseudo first-order kinetics. The optimal operating conditions for the degradation of 0.12 mM (74 mg L -1 ) dye concentration and mineralization of its aqueous solution were determined as GrF-ZnO-TiO 2 thin film anode, 100 mA current intensity, and 0.1 mM Fe 2+ (catalyst) concentration. Under these operating conditions, discoloration of AB10B solution was reached at 60 min while 6 h treatment needed for a mineralization degree of 91 %. Therefore, this study confirmed that the electrochemical process is effective for the degradation of AB10B in water using nanostructured ZnO-TiO 2 thin film anodes.

Time-lapse Raman imaging of osteoblast differentiation

PubMed Central

Hashimoto, Aya; Yamaguchi, Yoshinori; Chiu, Liang-da; Morimoto, Chiaki; Fujita, Katsumasa; Takedachi, Masahide; Kawata, Satoshi; Murakami, Shinya; Tamiya, Eiichi

2015-01-01

Osteoblastic mineralization occurs during the early stages of bone formation. During this mineralization, hydroxyapatite (HA), a major component of bone, is synthesized, generating hard tissue. Many of the mechanisms driving biomineralization remain unclear because the traditional biochemical assays used to investigate them are destructive techniques incompatible with viable cells. To determine the temporal changes in mineralization-related biomolecules at mineralization spots, we performed time-lapse Raman imaging of mouse osteoblasts at a subcellular resolution throughout the mineralization process. Raman imaging enabled us to analyze the dynamics of the related biomolecules at mineralization spots throughout the entire process of mineralization. Here, we stimulated KUSA-A1 cells to differentiate into osteoblasts and conducted time-lapse Raman imaging on them every 4 hours for 24 hours, beginning 5 days after the stimulation. The HA and cytochrome c Raman bands were used as markers for osteoblastic mineralization and apoptosis. From the Raman images successfully acquired throughout the mineralization process, we found that β-carotene acts as a biomarker that indicates the initiation of osteoblastic mineralization. A fluctuation of cytochrome c concentration, which indicates cell apoptosis, was also observed during mineralization. We expect time-lapse Raman imaging to help us to further elucidate osteoblastic mineralization mechanisms that have previously been unobservable. PMID:26211729

Time-lapse Raman imaging of osteoblast differentiation

NASA Astrophysics Data System (ADS)

Hashimoto, Aya; Yamaguchi, Yoshinori; Chiu, Liang-Da; Morimoto, Chiaki; Fujita, Katsumasa; Takedachi, Masahide; Kawata, Satoshi; Murakami, Shinya; Tamiya, Eiichi

2015-07-01

Osteoblastic mineralization occurs during the early stages of bone formation. During this mineralization, hydroxyapatite (HA), a major component of bone, is synthesized, generating hard tissue. Many of the mechanisms driving biomineralization remain unclear because the traditional biochemical assays used to investigate them are destructive techniques incompatible with viable cells. To determine the temporal changes in mineralization-related biomolecules at mineralization spots, we performed time-lapse Raman imaging of mouse osteoblasts at a subcellular resolution throughout the mineralization process. Raman imaging enabled us to analyze the dynamics of the related biomolecules at mineralization spots throughout the entire process of mineralization. Here, we stimulated KUSA-A1 cells to differentiate into osteoblasts and conducted time-lapse Raman imaging on them every 4 hours for 24 hours, beginning 5 days after the stimulation. The HA and cytochrome c Raman bands were used as markers for osteoblastic mineralization and apoptosis. From the Raman images successfully acquired throughout the mineralization process, we found that β-carotene acts as a biomarker that indicates the initiation of osteoblastic mineralization. A fluctuation of cytochrome c concentration, which indicates cell apoptosis, was also observed during mineralization. We expect time-lapse Raman imaging to help us to further elucidate osteoblastic mineralization mechanisms that have previously been unobservable.

30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

30 CFR 44.9 - Posting of petition.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Posting of petition. 44.9 Section 44.9 Mineral... REQUIREMENTS RULES OF PRACTICE FOR PETITIONS FOR MODIFICATION OF MANDATORY SAFETY STANDARDS General § 44.9 Posting of petition. An operator of a mine for which there is no representative of miners shall post a...

30 CFR 582.11 - Director's authority.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE... of two or more OCS mineral leases or portions of two or more OCS mineral leases into a single mining... leases or portions of leases as a single mining unit is in the interest of conservation of the natural...

30 CFR 582.11 - Director's authority.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE... of two or more OCS mineral leases or portions of two or more OCS mineral leases into a single mining... leases or portions of leases as a single mining unit is in the interest of conservation of the natural...

30 CFR 250.242 - What information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

....258; (q) Sulphur operations information required by § 250.259; (r) Coastal zone management information... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What information must accompany the DPP or DOCD? 250.242 Section 250.242 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR...

30 CFR 250.261 - What environmental impact analysis (EIA) information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Operations Coordination Documents (docd) § 250.261 What environmental impact analysis (EIA) information must... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What environmental impact analysis (EIA) information must accompany the DPP or DOCD? 250.261 Section 250.261 Mineral Resources MINERALS MANAGEMENT...

30 CFR 250.404 - What are the requirements for the crown block?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the requirements for the crown block? 250.404 Section 250.404 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... the results of this operational check in the driller's report. [68 FR 8423, Feb. 20, 2003] ...

Prediction of low bone mass using a combinational approach of cortical and trabecular bone measures from dental panoramic radiographs.

PubMed

Kathirvelu, D; Anburajan, M

2014-09-01

The aim of this study is to extract cortical and trabecular features of the mandible and to develop a novel combinational model of mandibular cortical thickness, trabecular bone area and age in order to predict low bone mineral density or osteoporosis from a dental panoramic radiograph. The study involved 64 south Indian women (age = 52.5 ± 12.7 years) categorised into two groups (normal and low bone mineral density) based on total femur bone mineral density. The dental panoramic radiographs were obtained by a digital scanner, and measurement of total bone mineral density at the right femur was performed by a dual-energy X-ray absorptiometry scanner. The mandibular cortical thickness and panoramic mandibular index were measured bilaterally, and the mean values were considered. The region of interest of 128 × 128 pixels around the mental foramen region was manually cropped and subjected to pre-processing, normalisation and average threshold-based segmentation to determine trabecular bone area. Multiple linear regression analyses of cortical and trabecular measures along with age were performed to develop a combinational model to classify subjects as normal and low bone mineral density. The proposed approach demonstrated strong correlation (r = 0.76; p < 0.01) against the total bone mineral density and resulted in accuracy, sensitivity and positive predictive values of 0.84, 0.92 and 0.85, respectively; the receiver operating characteristic outcomes disclosed that the area under the curve was 0.89.Our results suggest that the proposed combinational model could be useful to diagnose subjects with low bone mineral density. © IMechE 2014.

Antiquity of the biological sulphur cycle: evidence from sulphur and carbon isotopes in 2700 million-year-old rocks of the Belingwe Belt, Zimbabwe.

PubMed Central

Grassineau, N V; Nisbet, E G; Bickle, M J; Fowler, C M; Lowry, D; Mattey, D P; Abell, P; Martin, A

2001-01-01

Sulphur and carbon isotopic analyses on small samples of kerogens and sulphide minerals from biogenic and non-biogenic sediments of the 2.7 x 10(9) years(Ga)-old Belingwe Greenstone Belt (Zimbabwe) imply that a complex biological sulphur cycle was in operation. Sulphur isotopic compositions display a wider range of biological fractionation than hitherto reported from the Archaean. Carbon isotopic values in kerogen record fractionations characteristic of rubisco activity methanogenesis and methylotrophy and possibly anoxygenic photosynthesis. Carbon and sulphur isotopic fractionations have been interpreted in terms of metabolic processes in 2.7 Ga prokaryote mat communities, and indicate the operation of a diverse array of metabolic processes. The results are consistent with models of early molecular evolution derived from ribosomal RNA. PMID:11209879

A world of minerals in your mobile device

USGS Publications Warehouse

Jenness, Jane E.; Ober, Joyce A.; Wilkins, Aleeza M.; Gambogi, Joseph

2016-09-15

Mobile phones and other high-technology communications devices could not exist without mineral commodities. More than one-half of all components in a mobile device—including its electronics, display, battery, speakers, and more—are made from mined and semiprocessed materials (mineral commodities). Some mineral commodities can be recovered as byproducts during the production and processing of other commodities. As an example, bauxite is mined for its aluminum content, but gallium is recovered during the aluminum production process. The images show the ore minerals (sources) of some mineral commodities that are used to make components of a mobile device. On the reverse side, the map and table depict the major source countries producing these mineral commodities along with how these commodities are used in mobile devices. For more information on minerals, visit http://minerals.usgs.gov.

Conflict minerals from the Democratic Republic of the Congo—Tin processing plants, a critical part of the tin supply chain

USGS Publications Warehouse

Anderson, Charles

2015-03-24

Post-beneficiation processing plants (generally called smelters and refineries) for 3TG mineral ores and concentrates were identified by company and industry association representatives as being a link in the 3TG mineral supply chain through which these minerals can be traced to their source of origin (mine). The determination of the source of origin is critical to the development of a complete and transparent conflict-free mineral supply chain. Tungsten processing plants were the subject of the first fact sheet in this series published by the USGS NMIC in August 2014. Background information about historical conditions and multinational stakeholders’ voluntary due diligence guidance for minerals from conflict-affected and high-risk areas was presented in the tungsten fact sheet. Tantalum processing plants were the subject of the second fact sheet in this series published by the USGS NMIC in December 2014. This fact sheet, the third in the series about 3TG minerals, focuses on the tin supply chain by listing selected processors that produced tin materials commercially worldwide during 2013–14. It does not provide any information regarding the sources of the material processed in these facilities.

26 CFR 1.614-4 - Treatment under the Internal Revenue Code of 1939 with respect to separate operating mineral...

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Treatment under the Internal Revenue Code of 1939..., in the case of oil and gas wells. 1.614-4 Section 1.614-4 Internal Revenue INTERNAL REVENUE SERVICE....614-4 Treatment under the Internal Revenue Code of 1939 with respect to separate operating mineral...

Bibliography of articles and reports on mineral-separation techniques, processes, and applications

NASA Technical Reports Server (NTRS)

Harmon, R. S.

1971-01-01

A bibliography of published articles and reports on mineral-separation techniques, processes, and applications is presented along with an author and subject index. This information is intended for use in the mineral-separation facility of the Lunar Receiving Laboratory at the NASA Manned Spacecraft Center and as an aid and reference to persons involved or interested in mineral separation.

Titanium mineral resources in heavy-mineral sands in the Atlantic coastal plain of the southeastern United States

USGS Publications Warehouse

Van Gosen, Bradley S.; Ellefsen, Karl J.

2018-04-16

This study examined titanium distribution in the Atlantic Coastal Plain of the southeastern United States; the titanium is found in heavy-mineral sands that include the minerals ilmenite (Fe2+TiO3), rutile (TiO2), or leucoxene (an alteration product of ilmenite). Deposits of heavy-mineral sands in ancient and modern coastal plains are a significant feedstock source for the titanium dioxide pigments industry. Currently, two heavy-mineral sands mining and processing operations are active in the southeast United States producing concentrates of ilmenite-leucoxene, rutile, and zircon. The results of this study indicate the potential for similar deposits in many areas of the Atlantic Coastal Plain.This study used the titanium analyses of 3,457 stream sediment samples that were analyzed as part of the U.S. Geological Survey’s National Geochemical Survey program. This data set was analyzed by an integrated spatial modeling technique known as Bayesian hierarchical modeling to map the regional-scale, spatial distribution of titanium concentrations. In particular, clusters of anomalous concentrations of titanium occur: (1) along the Fall Zone, from Virginia to Alabama, where metamorphic and igneous rocks of the Piedmont region contact younger sediments of the Coastal Plain; (2) a paleovalley near the South Carolina and North Carolina border; (3) the upper and middle Atlantic Coastal Plain of North Carolina; (4) the majority of the Atlantic Coastal Plain of Virginia; and (5) barrier islands and stretches of the modern shoreline from South Carolina to northeast Florida. The areas mapped by this study could help mining companies delimit areas for exploration.

Optimization of the Electrochemical Extraction and Recovery of Metals from Electronic Waste Using Response Surface Methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diaz, Luis A.; Clark, Gemma G.; Lister, Tedd E.

The rapid growth of the electronic waste can be viewed both as an environmental threat and as an attractive source of minerals that can reduce the mining of natural resources, and stabilize the market of critical materials, such as rare earths. Here in this article surface response methodology was used to optimize a previously developed electrochemical recovery process for base metals from electronic waste using a mild oxidant (Fe 3+). Through this process an effective extraction of base metals can be achieved enriching the concentration of precious metals and significantly reducing environmental impacts and operational costs associated with the wastemore » generation and chemical consumption. The optimization was performed using a bench-scale system specifically designed for this process. Operational parameters such as flow rate, applied current density and iron concentration were optimized to reduce the specific energy consumption of the electrochemical recovery process to 1.94 kWh per kg of metal recovered at a processing rate of 3.3 g of electronic waste per hour.« less

Optimization of the Electrochemical Extraction and Recovery of Metals from Electronic Waste Using Response Surface Methodology

DOE PAGES

Diaz, Luis A.; Clark, Gemma G.; Lister, Tedd E.

2017-06-08

The rapid growth of the electronic waste can be viewed both as an environmental threat and as an attractive source of minerals that can reduce the mining of natural resources, and stabilize the market of critical materials, such as rare earths. Here in this article surface response methodology was used to optimize a previously developed electrochemical recovery process for base metals from electronic waste using a mild oxidant (Fe 3+). Through this process an effective extraction of base metals can be achieved enriching the concentration of precious metals and significantly reducing environmental impacts and operational costs associated with the wastemore » generation and chemical consumption. The optimization was performed using a bench-scale system specifically designed for this process. Operational parameters such as flow rate, applied current density and iron concentration were optimized to reduce the specific energy consumption of the electrochemical recovery process to 1.94 kWh per kg of metal recovered at a processing rate of 3.3 g of electronic waste per hour.« less

43 CFR 3275.11 - What are a facility operator's obligations?

Code of Federal Regulations, 2011 CFR

2011-10-01

... of, or damage to, geothermal and other energy and minerals resources; and (d) Comply with the... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) GEOTHERMAL RESOURCE LEASING...

Soil developments in polar deserts: Implications for exobiology and future Mars missions

NASA Technical Reports Server (NTRS)

Gibson, Everett K., Jr.

1989-01-01

Chemical alterations, weathering, and diagenesis of soil profiles from the dry valleys of Antarctica were studied as analogs of regolith development for the Martian regolith. Chemical weathering processes play an important part in soil development within the dry valleys of Antarctica. A suite of core samples were studied which were taken within the valley floors in addition to samples taken in the vicinity of evaporite and brine ponds. Analysis of water soluable cations and anions from core samples were performed along with petrographic analysis of selected samples. It was shown that ionic transport processes operate primarily above the permafrost zone. Abundances of the water soluable ions reflect the nature of secondary minerals produced by evaporation and weathering. Chloride, calcium, and sodium abundances for soils from the cores within the North and South Forks of Wright Valley, reflect the secondary mineralogy of the soil columns. Calculations for Na, Ca, and Cl abundances reflect the appearance of halite and antarcticite. In areas where excess Ca is present, X-ray diffraction studies show the presence of gypsum. It is well known that the Martian surface conditions may be favorable for chemical weathering. Primary silicates would be expected to be reactive with any ground water. It seems likely that Martian subsurface water is available to assist in the weathering of the primary minerals. Such weathering could result in the formation of clays, sulfates, carbonates, hydrates, halides, and zeolites. The dry valley cores have shown that they maybe excellent analogs to weathering processes on the near-surface of Mars. Since movement of water within the near-surface region clearly results in chemical weathering, leaching, and salt formation in the dry valleys, similar processes are probably operating within the Martian regolith.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirk, D.W.

The generation of industrial solid wastes containing leachable species of environmental concern is a problem for developing and developed nations alike. These materials arise from direct processing of mineral ores, from production of metals and minerals, from manufacturing operations, and from air and water pollution treatment processes. The general characteristics that make these wastes intractable is that their content of hazardous species is not easily liberated from the waste yet is not bound so tightly that they are safe for landfill disposal or industrial use. The approach taken in this work is a thermal treatment that separates the inorganic contaminantsmore » from the wastes. The objective is to provide recovery and reuse of both the residual solids and liberated contaminants. The results from operating this technique using two very different types of waste are described. The reasons that the process will work for a wide variety of wastes are explored. By using the knowledge of the thermodynamic stability of the phases found from the characterization analyses, a thermal regime was found that allowed separation of the contaminants without capturing the matrix materials. Bench scale studies were carried out using a tube furnace. Samples of the wastes were heated in crucible boats from 750 to 1150{degrees}C in the presence of various chlorinating agents. The offgas contained 90{sup +}% of the targeted contaminants despite their complex matrix form. The residue was free of contamination. As a result of the efficient concentrating mechanism of the process, the contaminants in the offgas solids are attractive for reuse in metallurgical industries. As an additional benefit, the organic contaminants of the residues were eliminated. Dioxin traces in the solids before treatment were absent after treatment. 15 refs., 4 figs., 4 tabs.« less

Conflict minerals from the Democratic Republic of the Congo: global tantalum processing plants, a critical part of the tantalum supply chain

USGS Publications Warehouse

Papp, John F.

2014-01-01

Post-beneficiation processing plants (generally called smelters and refineries) for 3TG mineral ores and concentrates were identified by company and industry association representatives as being the link in the 3TG mineral supply chain through which these minerals can be traced to their source of origin (mine). The determination of the source of origin is critical to the development of a complete and transparent conflict-free mineral supply chain. Tungsten processing plants were the subject of the first fact sheet in this series published by USGS NMIC in August 2014. Background information about historical conditions and multinational stakeholders’ voluntary due diligence guidance for minerals from conflict-affected and high-risk areas is presented in the tungsten fact sheet. This fact sheet, the second in a series about 3TG minerals, focuses on the tantalum supply chain by listing selected processors that produced tantalum materials commercially worldwide during 2013–14. It does not provide any information regarding the sources of material processed in these facilities.

Numerical modelling of fluid-rock interactions: Lessons learnt from carbonate rocks diagenesis studies

NASA Astrophysics Data System (ADS)

Nader, Fadi; Bachaud, Pierre; Michel, Anthony

2015-04-01

Quantitative assessment of fluid-rock interactions and their impact on carbonate host-rocks has recently become a very attractive research topic within academic and industrial realms. Today, a common operational workflow that aims at predicting the relevant diagenetic processes on the host rocks (i.e. fluid-rock interactions) consists of three main stages: i) constructing a conceptual diagenesis model including inferred preferential fluids pathways; ii) quantifying the resulted diagenetic phases (e.g. depositing cements, dissolved and recrystallized minerals); and iii) numerical modelling of diagenetic processes. Most of the concepts of diagenetic processes operate at the larger, basin-scale, however, the description of the diagenetic phases (products of such processes) and their association with the overall petrophysical evolution of sedimentary rocks remain at reservoir (and even outcrop/ well core) scale. Conceptual models of diagenetic processes are thereafter constructed based on studying surface-exposed rocks and well cores (e.g. petrography, geochemistry, fluid inclusions). We are able to quantify the diagenetic products with various evolving techniques and on varying scales (e.g. point-counting, 2D and 3D image analysis, XRD, micro-CT and pore network models). Geochemical modelling makes use of thermodynamic and kinetic rules as well as data-bases to simulate chemical reactions and fluid-rock interactions. This can be through a 0D model, whereby a certain process is tested (e.g. the likelihood of a certain chemical reaction to operate under specific conditions). Results relate to the fluids and mineral phases involved in the chemical reactions. They could be used as arguments to support or refute proposed outcomes of fluid-rock interactions. Coupling geochemical modelling with transport (reactive transport model; 1D, 2D and 3D) is another possibility, attractive as it provides forward simulations of diagenetic processes and resulting phases. This contribution is based on several studies that were undertaken on carbonate rocks diagenesis in some of the major reservoir rocks in the Middle East and outcrop analogues in Europe. Here, the main processes at hand are related to fracture-related dolomitization and carbonate dissolution. We would like to present the workflows we have followed and the questioning that resulted for a series of case studies. The way forward, seems evident as the integration of workflows and numerical modelling tools at different scales, bringing better constrains on the boundary data and less uncertainty.

A novel mineral flotation process using Thiobacillus ferrooxidans.

PubMed

Nagaoka, T; Ohmura, N; Saiki, H

1999-08-01

Oxidative leaching of metals by Thiobacillus ferrooxidans has proven useful in mineral processing. Here, we report on a new use for T. ferrooxidans, in which bacterial adhesion is used to remove pyrite from mixtures of sulfide minerals during flotation. Under control conditions, the floatabilities of five sulfide minerals tested (pyrite, chalcocite, molybdenite, millerite, and galena) ranged from 90 to 99%. Upon addition of T. ferrooxidans, the floatability of pyrite was significantly suppressed to less than 20%. In contrast, addition of the bacterium had little effect on the floatabilities of the other minerals, even when they were present in relatively large quantities: their floatabilities remained in the range of 81 to 98%. T. ferrooxidans thus appears to selectively suppress pyrite floatability. As a consequence, 77 to 95% of pyrite was removed from mineral mixtures while 72 to 100% of nonpyrite sulfide minerals was recovered. The suppression of pyrite floatability was caused by bacterial adhesion to pyrite surfaces. When normalized to the mineral surface area, the number of cells adhering to pyrite was significantly larger than the number adhering to other minerals. These results suggest that flotation with T. ferrooxidans may provide a novel approach to mineral processing in which the biological functions involved in cell adhesion play a key role in the separation of minerals.

A Novel Mineral Flotation Process Using Thiobacillus ferrooxidans

PubMed Central

Nagaoka, Toru; Ohmura, Naoya; Saiki, Hiroshi

1999-01-01

Oxidative leaching of metals by Thiobacillus ferrooxidans has proven useful in mineral processing. Here, we report on a new use for T. ferrooxidans, in which bacterial adhesion is used to remove pyrite from mixtures of sulfide minerals during flotation. Under control conditions, the floatabilities of five sulfide minerals tested (pyrite, chalcocite, molybdenite, millerite, and galena) ranged from 90 to 99%. Upon addition of T. ferrooxidans, the floatability of pyrite was significantly suppressed to less than 20%. In contrast, addition of the bacterium had little effect on the floatabilities of the other minerals, even when they were present in relatively large quantities: their floatabilities remained in the range of 81 to 98%. T. ferrooxidans thus appears to selectively suppress pyrite floatability. As a consequence, 77 to 95% of pyrite was removed from mineral mixtures while 72 to 100% of nonpyrite sulfide minerals was recovered. The suppression of pyrite floatability was caused by bacterial adhesion to pyrite surfaces. When normalized to the mineral surface area, the number of cells adhering to pyrite was significantly larger than the number adhering to other minerals. These results suggest that flotation with T. ferrooxidans may provide a novel approach to mineral processing in which the biological functions involved in cell adhesion play a key role in the separation of minerals. PMID:10427053

Study on the Classification of the Uranium Mineral of Venta de Cardena; ESTUDIO SOBRE LA CLASIFICACION DEL MINERAL DE VENTA DE CARDENA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Otero, A.R.

1959-01-01

The behavior of uranium mineral from Venta de Cardena in a spiral classifier which operates in a closed system with a ball mill was studied to obtain data for the design of a milling-classification system with a production capacity of 200 tons per day with a particle size less than 0.417 mm. The characteristics of such a system, the problems in normal operation, the inconveriences which these cause, and their solution were investigated. Correlations between these tests and the results obtained with long glass tubes are presented. (J.S.R.)

Vulnerability of soils towards mining operations in gold-bearing sands in Chile

NASA Astrophysics Data System (ADS)

Jordán, Manuel Miguel; González, Irma; Bech, Jaume; Sanfeliu, Teófilo; Pardo, Francisco

2015-04-01

The contamination levels in handicraft mining, despite less production and processing less equipment, have high repercussions upon the environment in many cases. High-grade ore extraction, flotation, gravity concentration, acid leaching cementation and mercury amalgamation are the main metallurgical technologies employed. Gold recovery involving milling and amalgamation appears to the most contamination source of mercury. This research work is only a starting point for carrying out a risk probability mapping of pollutants of the gold bearing sands. In southern Chile, with a mild and rainy climate, high levels of pollutants have been detected in some gold placer deposits. The handicraft gold-bearing sands studied are located in X Region of "Los Lagos" in southern Chile. A great quantity of existing secondary deposits in the X Region is located in the coastal mountain range. The lithological units that are found in this range correspond with metamorphic rocks of a Paleozoic crystalline base that present an auriferous content liberated from the successive erosive processes suffered. Metasedimentary and metavolcanic rocks also make up part of this range, but their auriferous load is much smaller. The methodology used in the characterization of the associated mineralization consists of testing samples with a grain size distribution, statistical parameter analysis and mineralogical analysis using a petrographic microscope, XRD and SEM/EDX. The chemical composition was determined by means of XRF and micro-chemical analysis. The major concentrations of heavy minerals are located in areas of dynamic river energy. In the studied samples, more the 75 % of the heavy minerals were distributed among grain sizes corresponding to thin sand (0.25-0.05 mm) with good grain selection. The main minerals present in the selected analysed samples were gold, zircon, olivine, ilmenite, hornblende, hematite, garnet, choromite, augite, epidote, etc. The main heavy metals found were mercury, lead, cadmium, crome, zinc, cobalt, cooper, platinum, gold, indium, tellurium, etc., and as well some traces of cerium, praseodymium, gadolinium, neodymium, samarium and lanthanum. The recurring presence of Pb, sulphur and Hg, among others, in mineral species like galena and cinnabar reveal accumulation indices, a product of the contaminating action of human beings. This is notable since no records exist of natural deposits of these minerals that can justify their presence, and records were utilized from semi-industrial exploitations for the extaction of gold where Hg is utilized in the amalgamation processes.

Women, mercury and artisanal gold mining : Risk communication and mitigation

NASA Astrophysics Data System (ADS)

Hinton, J. J.; Veiga, M. M.; Beinhoff, C.

2003-05-01

Artisanal miners employ rudimentary techniques for minéral extraction and often operate under hazardous, labour intensive, highly disorganized and illegal conditions. Gold is the main mineral extracted by artisanal miners, and the ecological and human health impacts resulting from mercury (Hg) use in gold extraction warrant special consideration. More than 30% of world's 13 million artisanal miners are women and, as they are often perceived to be less suited for labour intensive mining methods, the majority of women work in the processing aspect of artisanal mining, including amalgamation with Hg. As women are also predominantly responsible for food preparation, they are in an excellent position to respond to health risks associated with consumption of Hg-contaminated foods in impacted areas. In addition to their influence on consumption habits, women in artisanal mining communities may be in a position to effect positive change with respect to the technologies employed. Thus, gender sensitive approaches are necessary to reduce exposure risks to women and their families, promote clean technologies and support the development of stronger, healthier artisanal mining communities. This paper describes the roles of women in artisanal gold mining, highlights their importance in reducing the Hg exposure in these communities, and provides insight into how risks from Hg pollution can effectively be communicated and mitigated.

Degradation pathways of aniline in aqueous solutions during electro-oxidation with BDD electrodes and UV/H2O2 treatment.

PubMed

Benito, Aleix; Penadés, Aida; Lliberia, Josep Lluis; Gonzalez-Olmos, Rafael

2017-01-01

In this work, it has been studied the mineralization of aniline, a toxic substance of low biodegradability typically found in many industrial wastewaters, through electro-oxidation using boron doped diamond (BDD) electrodes and photo-oxidation (UV photolysis and UV/H 2 O 2 treatments). It was observed that in electro-oxidation and UV/H 2 O 2 , it was feasible to reach aniline mineralizations higher than 85%. Two different degradation routes have been observed during the aniline oxidation in these two treatments. The first route was the mineralization pathway, in which aniline was oxidized to CO 2 , water and nitrate. The second route was the polyaniline pathway in which polyanilines of high molecular weight are formed. The intermediate compounds involved in both degradation routes are different depending on the treatment used. In the electro-oxidation, denitrification processes were also observed. From an economical point of view, electro-oxidation of aniline using BDD electrodes is more interesting than UV/H 2 O 2 due it has an 87% lower operational cost. So, electro-oxidation using BDD electrodes seems to be a more suitable technique for the mineralization of wastewater containing aniline than UV or H 2 O 2 based technologies. Copyright © 2016 Elsevier Ltd. All rights reserved.

30 CFR 281.32 - Waiver, suspension, or reduction of rental, minimum royalty or production royalty.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Waiver, suspension, or reduction of rental, minimum royalty or production royalty. 281.32 Section 281.32 Mineral Resources BUREAU OF OCEAN ENERGY... the location and extent of all mining operations and a tabulated statement of the minerals mined and...

30 CFR 250.260 - What Coastal Zone Management Act (CZMA) information must accompany the DPP or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What Coastal Zone Management Act (CZMA) information must accompany the DPP or DOCD? 250.260 Section 250.260 Mineral Resources MINERALS MANAGEMENT... Operations Coordination Documents (docd) § 250.260 What Coastal Zone Management Act (CZMA) information must...

26 CFR 1.611-2 - Rules applicable to mines, oil and gas wells, and other natural deposits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... during each operating period, (iii) The average quality or grade of the mineral reserves, (iv) The... rate of exhaustion, quality or grade of the mineral, percentage of recovery, cost of development... the quality of the mineral valued, including the grade or gravity in the case of oil; (ix) The number...

30 CFR 250.291 - When and how must I submit the DWOP?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When and how must I submit the DWOP? 250.291 Section 250.291 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND... completed safety system design and before you begin to procure or fabricate the safety and operational...

30 CFR 254.1 - Who must submit a spill-response plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Who must submit a spill-response plan? 254.1 Section 254.1 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL-SPILL... spill-response plan? (a) If you are the owner or operator of an oil handling, storage, or transportation...

Electronic scraps--recovering of valuable materials from parallel wire cables.

PubMed

de Araújo, Mishene Christie Pinheiro Bezerra; Chaves, Arthur Pinto; Espinosa, Denise Crocce Romano; Tenório, Jorge Alberto Soares

2008-11-01

Every year, the number of discarded electro-electronic products is increasing. For this reason recycling is needed, to avoid wasting non-renewable natural resources. The objective of this work is to study the recycling of materials from parallel wire cable through unit operations of mineral processing. Parallel wire cables are basically composed of polymer and copper. The following unit operations were tested: grinding, size classification, dense medium separation, electrostatic separation, scrubbing, panning, and elutriation. It was observed that the operations used obtained copper and PVC concentrates with a low degree of cross contamination. It was concluded that total liberation of the materials was accomplished after grinding to less than 3 mm, using a cage mill. Separation using panning and elutriation presented the best results in terms of recovery and cross contamination.

Swelling properties of montmorillonite and beidellite clay minerals from molecular simulation: Comparison of temperature interlayer cation, and charge location effects

DOE PAGES

Teich-McGoldrick, Stephanie L.; Greathouse, Jeffery A.; Jove-Colon, Carlos F.; ...

2015-08-27

In this study, the swelling properties of smectite clay minerals are relevant to many engineering applications including environmental remediation, repository design for nuclear waste disposal, borehole stability in drilling operations, and additives for numerous industrial processes and commercial products. We used molecular dynamics and grand canonical Monte Carlo simulations to study the effects of layer charge location, interlayer cation, and temperature on intracrystalline swelling of montmorillonite and beidellite clay minerals. For a beidellite model with layer charge exclusively in the tetrahedral sheet, strong ion–surface interactions shift the onset of the two-layer hydrate to higher water contents. In contrast, for amore » montmorillonite model with layer charge exclusively in the octahedral sheet, weaker ion–surface interactions result in the formation of fully hydrated ions (two-layer hydrate) at much lower water contents. Clay hydration enthalpies and interlayer atomic density profiles are consistent with the swelling results. Water adsorption isotherms from grand canonical Monte Carlo simulations are used to relate interlayer hydration states to relative humidity, in good agreement with experimental findings.« less

Generation and Performance of Automated Jarosite Mineral Detectors for Vis/NIR Spectrometers at Mars

NASA Technical Reports Server (NTRS)

Gilmore, M. S.; Bornstein, B.; Merrill, M. D.; Castano, R.; Greenwood, J. P.

2005-01-01

Sulfate salt discoveries at the Eagle and Endurance craters in Meridiani Planum by the Mars Exploration Rover Opportunity have proven mineralogically the existence and involvement of water in Mars past. Visible and near infrared spectrometers like the Mars Express OMEGA, the Mars Reconnaissance Orbiter CRISM and the 2009 Mars Science Laboratory Rover cameras are powerful tools for the identification of water-bearing salts and other high priority minerals at Mars. The increasing spectral resolution and rover mission lifetimes represented by these missions currently necessitate data compression in order to ease downlink restrictions. On board data processing techniques can be used to guide the selection, measurement and return of scientifically important data from relevant targets, thus easing bandwidth stress and increasing scientific return. We have developed an automated support vector machine (SVM) detector operating in the visible/near-infrared (VisNIR, 300-2500 nm) spectral range trained to recognize the mineral jarosite (typically KFe3(SO4)2(OH)6), positively identified by the Mossbauer spectrometer at Meridiani Planum. Additional information is included in the original extended abstract.

Promising Technologies of Mining and Processing of Solid Minerals

NASA Astrophysics Data System (ADS)

Shabaev, Sergey; Ivanov, Seregey; Vakhianov, Evgeniy

2017-11-01

The continuing growth in mineral extraction entails an increase in industrial waste, which in turn has a negative impact on the environment. Rubber-tired vehicles, in which the tires wear colossally, is mainly used as a transport for loading, unloading, transportation and other types of work in the extraction of solid minerals. The used tires are not disposed in any way, but are stored in special areas where harmful toxic substances are emitted under the influence of ultraviolet rays. Therefore, a decision was made to find a method for utilization and rational use of industrial waste in the road construction sector. The operating temperature of composite rubber-bituminous binders based on rubber crumb from the used automobile tires is estimated in this paper, which is necessary for assigning technological parameters of production and laying of asphalt-concrete mixtures produced on their basis. It is established that composite rubber-bituminous binders based on rubber chips from the used automobile tires, produced according to the two-stage technology, have the same viscosity as the original petroleum bitumen, at a temperature increased by 20°C.