Enhanced auditory spatial localization in blind echolocators.

PubMed

Vercillo, Tiziana; Milne, Jennifer L; Gori, Monica; Goodale, Melvyn A

2015-01-01

Echolocation is the extraordinary ability to represent the external environment by using reflected sound waves from self-generated auditory pulses. Blind human expert echolocators show extremely precise spatial acuity and high accuracy in determining the shape and motion of objects by using echoes. In the current study, we investigated whether or not the use of echolocation would improve the representation of auditory space, which is severely compromised in congenitally blind individuals (Gori et al., 2014). The performance of three blind expert echolocators was compared to that of 6 blind non-echolocators and 11 sighted participants. Two tasks were performed: (1) a space bisection task in which participants judged whether the second of a sequence of three sounds was closer in space to the first or the third sound and (2) a minimum audible angle task in which participants reported which of two sounds presented successively was located more to the right. The blind non-echolocating group showed a severe impairment only in the space bisection task compared to the sighted group. Remarkably, the three blind expert echolocators performed both spatial tasks with similar or even better precision and accuracy than the sighted group. These results suggest that echolocation may improve the general sense of auditory space, most likely through a process of sensory calibration. Copyright © 2014 Elsevier Ltd. All rights reserved.

Underwater auditory localization by a swimming harbor seal (Phoca vitulina).

PubMed

Bodson, Anais; Miersch, Lars; Mauck, Bjoern; Dehnhardt, Guido

2006-09-01

The underwater sound localization acuity of a swimming harbor seal (Phoca vitulina) was measured in the horizontal plane at 13 different positions. The stimulus was either a double sound (two 6-kHz pure tones lasting 0.5 s separated by an interval of 0.2 s) or a single continuous sound of 1.2 s. Testing was conducted in a 10-m-diam underwater half circle arena with hidden loudspeakers installed at the exterior perimeter. The animal was trained to swim along the diameter of the half circle and to change its course towards the sound source as soon as the signal was given. The seal indicated the sound source by touching its assumed position at the board of the half circle. The deviation of the seals choice from the actual sound source was measured by means of video analysis. In trials with the double sound the seal localized the sound sources with a mean deviation of 2.8 degrees and in trials with the single sound with a mean deviation of 4.5 degrees. In a second experiment minimum audible angles of the stationary animal were found to be 9.8 degrees in front and 9.7 degrees in the back of the seal's head.

49 CFR 214.339 - Audible warning from trains.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Audible warning from trains. 214.339 Section 214... Audible warning from trains. Each railroad shall require that the locomotive whistle be sounded, and the locomotive bell be rung, by trains approaching roadway workers on or about the track. Such audible warning...

49 CFR 214.339 - Audible warning from trains.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Audible warning from trains. 214.339 Section 214... Audible warning from trains. Each railroad shall require that the locomotive whistle be sounded, and the locomotive bell be rung, by trains approaching roadway workers on or about the track. Such audible warning...

49 CFR 214.339 - Audible warning from trains.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Audible warning from trains. 214.339 Section 214... Audible warning from trains. Each railroad shall require that the locomotive whistle be sounded, and the locomotive bell be rung, by trains approaching roadway workers on or about the track. Such audible warning...

49 CFR 214.339 - Audible warning from trains.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Audible warning from trains. 214.339 Section 214... Audible warning from trains. Each railroad shall require that the locomotive whistle be sounded, and the locomotive bell be rung, by trains approaching roadway workers on or about the track. Such audible warning...

49 CFR 214.339 - Audible warning from trains.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Audible warning from trains. 214.339 Section 214... Audible warning from trains. Each railroad shall require that the locomotive whistle be sounded, and the locomotive bell be rung, by trains approaching roadway workers on or about the track. Such audible warning...

Research on the correlation between corona current spectrum and audible noise spectrum of HVDC transmission line

NASA Astrophysics Data System (ADS)

Liu, Yingyi; Zhou, Lijuan; Liu, Yuanqing; Yuan, Haiwen; Ji, Liang

2017-11-01

Audible noise is closely related to corona current on a high voltage direct current (HVDC) transmission line. In this paper, we measured a large amount of audible noise and corona current waveforms simultaneously based on the largest outdoor HVDC corona cage all over the world. By analyzing the experimental data, the related statistical regularities between a corona current spectrum and an audible noise spectrum were obtained. Furthermore, the generation mechanism of audible noise was analyzed theoretically, and the related mathematical expression between the audible noise spectrum and the corona current spectrum, which is suitable for all of these measuring points in the space, has been established based on the electro-acoustic conversion theory. Finally, combined with the obtained mathematical relation, the internal reasons for these statistical regularities appearing in measured corona current and audible noise data were explained. The results of this paper not only present the statistical association regularities between the corona current spectrum and the audible noise spectrum on a HVDC transmission line, but also reveal the inherent reasons of these associated rules.

Correlation between audible noise and corona current generated by AC corona discharge in time and frequency domains

NASA Astrophysics Data System (ADS)

Li, Xuebao; Wang, Jing; Li, Yinfei; Zhang, Qian; Lu, Tiebing; Cui, Xiang

2018-06-01

Corona-generated audible noise is induced by the collisions between space charges and air molecules. It has been proven that there is a close correlation between audible noise and corona current from DC corona discharge. Analysis on the correlation between audible noise and corona current can promote the cognition of the generation mechanism of corona discharge. In this paper, time-domain waveforms of AC corona-generated audible noise and corona current are measured simultaneously. The one-to-one relationship between sound pressure pulses and corona current pulses can be found and is used to remove the interferences from background noise. After the interferences are removed, the linear correlated relationships between sound pressure pulse amplitude and corona current pulse amplitude are obtained through statistical analysis. Besides, frequency components at the harmonics of power frequency (50 Hz) can be found both in the frequency spectrums of audible noise and corona current through frequency analysis. Furthermore, the self-correlation relationships between harmonic components below 400 Hz with the 50 Hz component are analyzed for audible noise and corona current and corresponding empirical formulas are proposed to calculate the harmonic components based on the 50 Hz component. Finally, based on the AC corona discharge process and generation mechanism of audible noise and corona current, the correlation between audible noise and corona current in time domain and frequency domain are interpreted qualitatively. Besides, with the aid of analytical expressions of periodic square waves, sound pressure pulses, and corona current pulses, the modulation effects from the AC voltage on the pulse trains are used to interpret the generation of the harmonic components of audible noise and corona current.

Remote infrared audible signage (RIAS) pilot program report.

DOT National Transportation Integrated Search

2011-07-01

The Remote Infrared Audible Sign Model Accessibility Program (RIAS MAP) is a program funded by the Federal Transit Administration (FTA) to evaluate the effectiveness of remote infrared audible sign systems in enabling persons with visual and cognitiv...

Underwater localization of pure tones by harbor seals (Phoca vitulina).

PubMed

Bodson, Anaïs; Miersch, Lars; Dehnhardt, Guido

2007-10-01

The underwater sound localization acuity of harbor seals (Phoca vitulina) was measured in the horizontal plane. Minimum audible angles (MAAs) of pure tones were determined as a function of frequency from 0.2 to 16 kHz for two seals. Testing was conducted in a 10-m-diam underwater half circle using a right/left psychophysical procedure. The results indicate that for both harbor seals, MAAs were large at high frequencies (13.5 degrees and 17.4 degrees at 16 kHz), transitional at intermediate frequencies (9.6 degrees and 10.1 degrees at 4 kHz), and particularly small at low frequencies (3.2 degrees and 3.1 degrees at 0.2 kHz). Harbor seals seem to be able to utilize both binaural cues, interaural time differences (ITDs) and interaural intensity differences (IIDs), but a significant decrease in the sound localization acuity with increasing frequency suggests that IID cues may not be as robust as ITD cues under water. These results suggest that the harbor seal can be regarded as a low-frequency specialist. Additionally, to obtain a MAA more representative of the species, the horizontal underwater MAA of six adult harbor seals was measured at 2 kHz under identical conditions. The MAAs of the six animals ranged from 8.8 degrees to 11.7 degrees , resulting in a mean MAA of 10.3 degrees .

High resolution miniaturized stepper ultrasonic motor using differential composite motion.

PubMed

Chu, Xiangcheng; Xing, Zengping; Li, Longtu; Gui, Zhilun

2004-03-01

Experiments show that there is a limited minimum stepped angle in ultrasonic motors (USM). The research on the minimum angle of stepper USM with 15 mm in diameter and wobbling mode is being carried out. This paper presents a novel way to decrease the minimum stepped angle of USM based on the principle of differential composite motion (DCM), i.e. clockwise and counterclockwise rotation. The prototype was fabricated and experiments proved that this method is useful and also keeps a high torque for a large stepped angle. The stator of the prototype is steel, and rotor is fiberglass, antifriction material or steel. The prototype can operate well over 150 h with a 5 kHz wide frequency band. The minimum stepped angle is 46" using a coventional method while 12" using DCM method proposed in this paper.

49 CFR 236.513 - Audible indicator.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards § 236.513 Audible indicator. (a) The automatic cab signal... control system shall have a distinctive sound and be clearly audible throughout the cab under all...

49 CFR 236.513 - Audible indicator.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards § 236.513 Audible indicator. (a) The automatic cab signal... control system shall have a distinctive sound and be clearly audible throughout the cab under all...

Multichannel Compression, Temporal Cues, and Audibility.

ERIC Educational Resources Information Center

Souza, Pamela E.; Turner, Christopher W.

1998-01-01

The effect of the reduction of the temporal envelope produced by multichannel compression on recognition was examined in 16 listeners with hearing loss, with particular focus on audibility of the speech signal. Multichannel compression improved speech recognition when superior audibility was provided by a two-channel compression system over linear…

Making Thinking Audible and Visible via Cooperative Learning

ERIC Educational Resources Information Center

Jacobs, George M.; Wang, Aili; Li, Xishuang; Xie, Yongye

2008-01-01

This chapter begins with a section that describes cooperative learning and explains eight cooperative learning principles. The second section looks briefly at why making thinking audible and visible enriches students' thinking. Making thinking audible means that teachers and students speak out what is going through their minds as they do a task,…

Methods and Applications of the Audibility Index in Hearing Aid Selection and Fitting

PubMed Central

Amlani, Amyn M.; Punch, Jerry L.; Ching, Teresa Y. C.

2002-01-01

During the first half of the 20th century, communications engineers at Bell Telephone Laboratories developed the articulation model for predicting speech intelligibility transmitted through different telecommunication devices under varying electroacoustic conditions. The profession of audiology adopted this model and its quantitative aspects, known as the Articulation Index and Speech Intelligibility Index, and applied these indices to the prediction of unaided and aided speech intelligibility in hearing-impaired listeners. Over time, the calculation methods of these indices—referred to collectively in this paper as the Audibility Index—have been continually refined and simplified for clinical use. This article provides (1) an overview of the basic principles and the calculation methods of the Audibility Index, the Speech Transmission Index and related indices, as well as the Speech Recognition Sensitivity Model, (2) a review of the literature on using the Audibility Index to predict speech intelligibility of hearing-impaired listeners, (3) a review of the literature on the applicability of the Audibility Index to the selection and fitting of hearing aids, and (4) a discussion of future scientific needs and clinical applications of the Audibility Index. PMID:25425917

The effect of a movie soundtrack on auditory event-related potentials in children, adolescents, and adults.

PubMed

Mahajan, Yatin; McArthur, Genevieve

2011-05-01

To determine if an audible movie soundtrack has a degrading effect on the auditory P1, N1, P2, N2, or mismatch negativity (MMN) event-related potentials (ERPs) in children, adolescents, or adults. The auditory ERPs of 36 children, 32 young adolescents, 19 older adolescents, and 10 adults were measured while they watched a movie in two conditions: with an audible soundtrack and with a silent soundtrack. In children and adolescents, the audible movie soundtrack had a significant impact on amplitude, latency or split-half reliability of the N1, P2, N2, and MMN ERPs. The audible soundtrack had minimal impact on the auditory ERPs of adults. These findings challenge previous claims that an audible soundtrack does not degrade the auditory ERPs of children. Further, the reliability of the MMN is poorer than P1, N1, P2, and N2 peaks in both sound-off and sound-on conditions. Researchers should be cautious about using an audible movie soundtrack when measuring auditory ERPs in younger listeners. Copyright © 2010 International Federation of Clinical Neurophysiology. All rights reserved.

Biological Effect of Audible Sound Control on Mung Bean (Vigna radiate) Sprout

PubMed Central

Cai, W.; He, H.; Zhu, S.; Wang, N.

2014-01-01

Audible sound (20–20000 Hz) widely exists in natural world. However, the interaction between audible sound and the growth of plants is usually neglected in biophysics research. Not much effort has been put forth in studying the relation of plant and audible sound. In this work, the effect of audible sound on germination and growth of mung bean (Vigna radiate) was studied under laboratory condition. Audible sound ranging 1000–1500 Hz, 1500–2000 Hz, and 2000–2500 Hz and intensities [80 dB (A), 90 dB (A), 100 dB (A)] were used to stimulate mung bean for 72 hours. The growth of mung bean was evaluated in terms of mean germination time, total length, and total fresh weight. Experimental results indicated that the sound wave can reduce the germination period of mung bean and the mung bean under treatments of sound with intensity around 90 dB and frequency around 2000 Hz and significant increase in growth. Audible sound treatment can promote the growth of mung bean differently for distinct frequency and intensity. The study provides us with a way to understand the effects and rules of sound field on plant growth and a new way to improve the production of mung bean. PMID:25170517

PT-SAFE: a software tool for development and annunciation of medical audible alarms.

PubMed

Bennett, Christopher L; McNeer, Richard R

2012-03-01

Recent reports by The Joint Commission as well as the Anesthesia Patient Safety Foundation have indicated that medical audible alarm effectiveness needs to be improved. Several recent studies have explored various approaches to improving the audible alarms, motivating the authors to develop real-time software capable of comparing such alarms. We sought to devise software that would allow for the development of a variety of audible alarm designs that could also integrate into existing operating room equipment configurations. The software is meant to be used as a tool for alarm researchers to quickly evaluate novel alarm designs. A software tool was developed for the purpose of creating and annunciating audible alarms. The alarms consisted of annunciators that were mapped to vital sign data received from a patient monitor. An object-oriented approach to software design was used to create a tool that is flexible and modular at run-time, can annunciate wave-files from disk, and can be programmed with MATLAB by the user to create custom alarm algorithms. The software was tested in a simulated operating room to measure technical performance and to validate the time-to-annunciation against existing equipment alarms. The software tool showed efficacy in a simulated operating room environment by providing alarm annunciation in response to physiologic and ventilator signals generated by a human patient simulator, on average 6.2 seconds faster than existing equipment alarms. Performance analysis showed that the software was capable of supporting up to 15 audible alarms on a mid-grade laptop computer before audio dropouts occurred. These results suggest that this software tool provides a foundation for rapidly staging multiple audible alarm sets from the laboratory to a simulation environment for the purpose of evaluating novel alarm designs, thus producing valuable findings for medical audible alarm standardization.

Health-Based Audible Noise Guidelines Account for Infrasound and Low-Frequency Noise Produced by Wind Turbines

PubMed Central

Berger, Robert G.; Ashtiani, Payam; Ollson, Christopher A.; Whitfield Aslund, Melissa; McCallum, Lindsay C.; Leventhall, Geoff; Knopper, Loren D.

2015-01-01

Setbacks for wind turbines have been established in many jurisdictions to address potential health concerns associated with audible noise. However, in recent years, it has been suggested that infrasound (IS) and low-frequency noise (LFN) could be responsible for the onset of adverse health effects self-reported by some individuals living in proximity to wind turbines, even when audible noise limits are met. The purpose of this paper was to investigate whether current audible noise-based guidelines for wind turbines account for the protection of human health, given the levels of IS and LFN typically produced by wind turbines. New field measurements of indoor IS and outdoor LFN at locations between 400 and 900 m from the nearest turbine, which were previously underrepresented in the scientific literature, are reported and put into context with existing published works. Our analysis showed that indoor IS levels were below auditory threshold levels while LFN levels at distances >500 m were similar to background LFN levels. A clear contribution to LFN due to wind turbine operation (i.e., measured with turbines on in comparison to with turbines off) was noted at a distance of 480 m. However, this corresponded to an increase in overall audible sound measures as reported in dB(A), supporting the hypothesis that controlling audible sound produced by normally operating wind turbines will also control for LFN. Overall, the available data from this and other studies suggest that health-based audible noise wind turbine siting guidelines provide an effective means to evaluate, monitor, and protect potential receptors from audible noise as well as IS and LFN. PMID:25759808

Health-based audible noise guidelines account for infrasound and low-frequency noise produced by wind turbines.

PubMed

Berger, Robert G; Ashtiani, Payam; Ollson, Christopher A; Whitfield Aslund, Melissa; McCallum, Lindsay C; Leventhall, Geoff; Knopper, Loren D

2015-01-01

Setbacks for wind turbines have been established in many jurisdictions to address potential health concerns associated with audible noise. However, in recent years, it has been suggested that infrasound (IS) and low-frequency noise (LFN) could be responsible for the onset of adverse health effects self-reported by some individuals living in proximity to wind turbines, even when audible noise limits are met. The purpose of this paper was to investigate whether current audible noise-based guidelines for wind turbines account for the protection of human health, given the levels of IS and LFN typically produced by wind turbines. New field measurements of indoor IS and outdoor LFN at locations between 400 and 900 m from the nearest turbine, which were previously underrepresented in the scientific literature, are reported and put into context with existing published works. Our analysis showed that indoor IS levels were below auditory threshold levels while LFN levels at distances >500 m were similar to background LFN levels. A clear contribution to LFN due to wind turbine operation (i.e., measured with turbines on in comparison to with turbines off) was noted at a distance of 480 m. However, this corresponded to an increase in overall audible sound measures as reported in dB(A), supporting the hypothesis that controlling audible sound produced by normally operating wind turbines will also control for LFN. Overall, the available data from this and other studies suggest that health-based audible noise wind turbine siting guidelines provide an effective means to evaluate, monitor, and protect potential receptors from audible noise as well as IS and LFN.

Dissecting auditory verbal hallucinations into two components: audibility (Gedankenlautwerden) and alienation (thought insertion).

PubMed

Sommer, Iris E; Selten, Jean-Paul; Diederen, Kelly M; Blom, Jan Dirk

2010-01-01

This study proposes a theoretical framework which dissects auditory verbal hallucinations (AVH) into 2 essential components: audibility and alienation. Audibility, the perceptual aspect of AVH, may result from a disinhibition of the auditory cortex in response to self-generated speech. In isolation, this aspect leads to audible thoughts: Gedankenlautwerden. The second component is alienation, which is the failure to recognize the content of AVH as self-generated. This failure may be related to the fact that cerebral activity associated with AVH is predominantly present in the speech production area of the right hemisphere. Since normal inner speech is derived from the left speech area, an aberrant source may lead to confusion about the origin of the language fragments. When alienation is not accompanied by audibility, it will result in the experience of thought insertion. The 2 hypothesized components are illustrated using case vignettes. Copyright 2010 S. Karger AG, Basel.

Reconfigurable Auditory-Visual Display

NASA Technical Reports Server (NTRS)

Begault, Durand R. (Inventor); Anderson, Mark R. (Inventor); McClain, Bryan (Inventor); Miller, Joel D. (Inventor)

2008-01-01

System and method for visual and audible communication between a central operator and N mobile communicators (N greater than or equal to 2), including an operator transceiver and interface, configured to receive and display, for the operator, visually perceptible and audibly perceptible signals from each of the mobile communicators. The interface (1) presents an audible signal from each communicator as if the audible signal is received from a different location relative to the operator and (2) allows the operator to select, to assign priority to, and to display, the visual signals and the audible signals received from a specified communicator. Each communicator has an associated signal transmitter that is configured to transmit at least one of the visual signals and the audio signal associated with the communicator, where at least one of the signal transmitters includes at least one sensor that senses and transmits a sensor value representing a selected environmental or physiological parameter associated with the communicator.

Evaluation of small arms noise in a natural soundscape-Bear Butte, SD

NASA Astrophysics Data System (ADS)

Braslau, David

2005-09-01

Most studies on soundscape intrusion have been limited to moving sources. Of less concern is noise from small arms. Potential impact was predicted from a proposed large small arms facility with 10000 rounds or more per day on the natural soundscape at Bear Butte, one of the most sacred sites of the Northern Cheyenne and other tribes. The primary impacted activity is meditation and oneness with the natural environment that can continue for several days through day and night. Non-natural sources included limited vehicles on a nearby highway and farm equipment, but few aircraft. Second-by-second ambient octave band readings were taken at 20 sites starting before sunrise. The minimum ambient level observed was 19.6 dBA but limits were encountered with a 1/2 in. microphone. Sound level data on small arms were projected from the proposed range four miles north of Bear Butte to elevated points on the Butte assuming a zero wind environment. Impact was evaluated using audibility, intrusiveness and impulse-weighted DNL. Projected levels were well above ambient. While the DNL was projected to increase by 15 dBA, this metric has little meaning for this type of activity. Assumptions related to outdoor sound propagation, audibility and impulsive noise perception are discussed.

Audibility and visual biasing in speech perception

NASA Astrophysics Data System (ADS)

Clement, Bart Richard

Although speech perception has been considered a predominantly auditory phenomenon, large benefits from vision in degraded acoustic conditions suggest integration of audition and vision. More direct evidence of this comes from studies of audiovisual disparity that demonstrate vision can bias and even dominate perception (McGurk & MacDonald, 1976). It has been observed that hearing-impaired listeners demonstrate more visual biasing than normally hearing listeners (Walden et al., 1990). It is argued here that stimulus audibility must be equated across groups before true differences can be established. In the present investigation, effects of visual biasing on perception were examined as audibility was degraded for 12 young normally hearing listeners. Biasing was determined by quantifying the degree to which listener identification functions for a single synthetic auditory /ba-da-ga/ continuum changed across two conditions: (1)an auditory-only listening condition; and (2)an auditory-visual condition in which every item of the continuum was synchronized with visual articulations of the consonant-vowel (CV) tokens /ba/ and /ga/, as spoken by each of two talkers. Audibility was altered by presenting the conditions in quiet and in noise at each of three signal-to- noise (S/N) ratios. For the visual-/ba/ context, large effects of audibility were found. As audibility decreased, visual biasing increased. A large talker effect also was found, with one talker eliciting more biasing than the other. An independent lipreading measure demonstrated that this talker was more visually intelligible than the other. For the visual-/ga/ context, audibility and talker effects were less robust, possibly obscured by strong listener effects, which were characterized by marked differences in perceptual processing patterns among participants. Some demonstrated substantial biasing whereas others demonstrated little, indicating a strong reliance on audition even in severely degraded acoustic conditions. Listener effects were not correlated with lipreading performance. The large effect of audibility suggests that conclusions regarding an increased reliance on vision among hearing- impaired listeners were premature, and that accurate comparisons only can be made after equating audibility. Further, if after such control, individual hearing- impaired listeners demonstrate the processing differences that were demonstrated in the present investigation, then these findings have the potential to impact aural rehabilitation strategies.

16 CFR Table 3 to Part 1512 - Minimum Acceptable Values for the Quantity A Defined in the Retroreflective Tire and Rim Test...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Minimum Acceptable Values for the Quantity A Defined in the Retroreflective Tire and Rim Test Procedure 3 Table 3 to Part 1512 Commercial Practices... Retroreflective Tire and Rim Test Procedure Observation angle (degrees) Entrance angle (degrees) Minimum...

Seeing Chemistry through Sound: A Submersible Audible Light Sensor for Observing Chemical Reactions for Students Who Are Blind or Visually Impaired

ERIC Educational Resources Information Center

Supalo, Cary A.; Kreuter, Rodney A.; Musser, Aaron; Han, Josh; Briody, Erika; McArtor, Chip; Gregory, Kyle; Mallouk, Thomas E.

2006-01-01

In order to enable students who are blind and visually impaired to observe chemical changes in solutions, a hand-held device was designed to output light intensity as an audible tone. The submersible audible light sensor (SALS) creates an audio signal by which one can observe reactions in a solution in real time, using standard laboratory…

Audible handheld Doppler ultrasound determines reliable and inexpensive exclusion of significant peripheral arterial disease.

PubMed

Alavi, Afsaneh; Sibbald, R Gary; Nabavizadeh, Reza; Valaei, Farnaz; Coutts, Pat; Mayer, Dieter

2015-12-01

To determine the accuracy of audible arterial foot signals with an audible handheld Doppler ultrasound for identification of significant peripheral arterial disease as a simple, quick, and readily available bedside screening tool. Two hundred consecutive patients referred to an interprofessional wound care clinic underwent audible handheld Doppler ultrasound of both legs. As a control and comparator, a formal bilateral lower leg vascular study including the calculation of Ankle Brachial Pressure Index and toe pressure (TP) was performed at the vascular lab. Diagnostic reliability of audible handheld Doppler ultrasound was calculated versus Ankle Brachial Pressure Index as the gold standard test. A sensitivity of 42.8%, a specificity of 97.5%, negative predictive value of 94.10%, positive predictive value of 65.22%, positive likelihood ratio of 17.52, and negative likelihood ratio of 0.59. The univariable logistic regression model had an area under the curve of 0.78. There was a statistically significant difference at the 5% level between univariable and multivariable area under the curves of the dorsalis pedis and posterior tibial models (p < 0.001). Audible handheld Doppler ultrasound proved to be a reliable, simple, rapid, and inexpensive bedside exclusion test of peripheral arterial disease in diabetic and nondiabetic patients. © The Author(s) 2015.

The influence of audibility on speech recognition with nonlinear frequency compression for children and adults with hearing loss

PubMed Central

McCreery, Ryan W.; Alexander, Joshua; Brennan, Marc A.; Hoover, Brenda; Kopun, Judy; Stelmachowicz, Patricia G.

2014-01-01

Objective The primary goal of nonlinear frequency compression (NFC) and other frequency lowering strategies is to increase the audibility of high-frequency sounds that are not otherwise audible with conventional hearing-aid processing due to the degree of hearing loss, limited hearing aid bandwidth or a combination of both factors. The aim of the current study was to compare estimates of speech audibility processed by NFC to improvements in speech recognition for a group of children and adults with high-frequency hearing loss. Design Monosyllabic word recognition was measured in noise for twenty-four adults and twelve children with mild to severe sensorineural hearing loss. Stimuli were amplified based on each listener’s audiogram with conventional processing (CP) with amplitude compression or with NFC and presented under headphones using a software-based hearing aid simulator. A modification of the speech intelligibility index (SII) was used to estimate audibility of information in frequency-lowered bands. The mean improvement in SII was compared to the mean improvement in speech recognition. Results All but two listeners experienced improvements in speech recognition with NFC compared to CP, consistent with the small increase in audibility that was estimated using the modification of the SII. Children and adults had similar improvements in speech recognition with NFC. Conclusion Word recognition with NFC was higher than CP for children and adults with mild to severe hearing loss. The average improvement in speech recognition with NFC (7%) was consistent with the modified SII, which indicated that listeners experienced an increase in audibility with NFC compared to CP. Further studies are necessary to determine if changes in audibility with NFC are related to speech recognition with NFC for listeners with greater degrees of hearing loss, with a greater variety of compression settings, and using auditory training. PMID:24535558

Audible vision for the blind and visually impaired in indoor open spaces.

PubMed

Yu, Xunyi; Ganz, Aura

2012-01-01

In this paper we introduce Audible Vision, a system that can help blind and visually impaired users navigate in large indoor open spaces. The system uses computer vision to estimate the location and orientation of the user, and enables the user to perceive his/her relative position to a landmark through 3D audio. Testing shows that Audible Vision can work reliably in real-life ever-changing environment crowded with people.

Sub-Audible Speech Recognition Based upon Electromyographic Signals

NASA Technical Reports Server (NTRS)

Jorgensen, Charles C. (Inventor); Agabon, Shane T. (Inventor); Lee, Diana D. (Inventor)

2012-01-01

Method and system for processing and identifying a sub-audible signal formed by a source of sub-audible sounds. Sequences of samples of sub-audible sound patterns ("SASPs") for known words/phrases in a selected database are received for overlapping time intervals, and Signal Processing Transforms ("SPTs") are formed for each sample, as part of a matrix of entry values. The matrix is decomposed into contiguous, non-overlapping two-dimensional cells of entries, and neural net analysis is applied to estimate reference sets of weight coefficients that provide sums with optimal matches to reference sets of values. The reference sets of weight coefficients are used to determine a correspondence between a new (unknown) word/phrase and a word/phrase in the database.

Tactical Sensors for Dispersed TNF (Tactical Nuclear Force) Units. Appendix 1.Tactical Sensory Survey.

DTIC Science & Technology

1983-06-30

activating a separate transmitter, audible alarm, or contact closure. This sensor is compatible with any device that utilizes an input pulse or...transmitter, audible alarm, or contact closure. This sensor is compatible *i with any device that utilizes an output to produce an alarm. 110-4769-002. This...used to generate an alarm by activating a separate transmitter, audible alarm, or contact closure. This sensor is compatible with any device that

A numerical model of acoustic wave caused by a single positive corona source

NASA Astrophysics Data System (ADS)

Zhang, Bo; Li, Zhen; He, Jinliang

2017-10-01

Audible noise accompanies corona discharge, which is one of the most important electromagnetic environment issues of high voltage transmission lines. Most of the studies on the audible noise generated by corona discharge focused on statistical analysis of the experimental results and a series of empirical formulas were derived to predict the audible noise. However, few of them interpreted the generating mechanism of the audible noise. Sound wave in the air is actually the fluctuation of the air, which lead to the hypothesis that the sound wave is generated by the interaction of the charged particles and the air molecules in the discharge progress. To validate this hypothesis, experiments were carried out in this paper to study the relationship between the audible noise and the corona current, including the correlation both in time domain and in frequency domain. Based on the experimental results, the fluid equations of the particles in the air were introduced to study the interactions among the electrons, ions, and neutral molecules in the discharge, and a numerical model for the amplitude of corona acoustic emission was developed and validated.

Audibility-based predictions of speech recognition for children and adults with normal hearing.

PubMed

McCreery, Ryan W; Stelmachowicz, Patricia G

2011-12-01

This study investigated the relationship between audibility and predictions of speech recognition for children and adults with normal hearing. The Speech Intelligibility Index (SII) is used to quantify the audibility of speech signals and can be applied to transfer functions to predict speech recognition scores. Although the SII is used clinically with children, relatively few studies have evaluated SII predictions of children's speech recognition directly. Children have required more audibility than adults to reach maximum levels of speech understanding in previous studies. Furthermore, children may require greater bandwidth than adults for optimal speech understanding, which could influence frequency-importance functions used to calculate the SII. Speech recognition was measured for 116 children and 19 adults with normal hearing. Stimulus bandwidth and background noise level were varied systematically in order to evaluate speech recognition as predicted by the SII and derive frequency-importance functions for children and adults. Results suggested that children required greater audibility to reach the same level of speech understanding as adults. However, differences in performance between adults and children did not vary across frequency bands. © 2011 Acoustical Society of America

Integrating the acoustics of running speech into the pure tone audiogram: a step from audibility to intelligibility and disability.

PubMed

Corthals, Paul

2008-01-01

The aim of the present study is to construct a simple method for visualizing and quantifying the audibility of speech on the audiogram and to predict speech intelligibility. The proposed method involves a series of indices on the audiogram form reflecting the sound pressure level distribution of running speech. The indices that coincide with a patient's pure tone thresholds reflect speech audibility and give evidence of residual functional hearing capacity. Two validation studies were conducted among sensorineurally hearing-impaired participants (n = 56 and n = 37, respectively) to investigate the relation with speech recognition ability and hearing disability. The potential of the new audibility indices as predictors for speech reception thresholds is comparable to the predictive potential of the ANSI 1968 articulation index and the ANSI 1997 speech intelligibility index. The sum of indices or a weighted combination can explain considerable proportions of variance in speech reception results for sentences in quiet free field conditions. The proportions of variance that can be explained in questionnaire results on hearing disability are less, presumably because the threshold indices almost exclusively reflect message audibility and much less the psychosocial consequences of hearing deficits. The outcomes underpin the validity of the new audibility indexing system, even though the proposed method may be better suited for predicting relative performance across a set of conditions than for predicting absolute speech recognition performance. (c) 2007 S. Karger AG, Basel

Effectiveness of Audible Warning Devices on Emergency Vehicles.

DOT National Transportation Integrated Search

1977-08-01

The purpose of the study was to examine the effectiveness of audible warning devices (AWD's) on emergency vehicles in terms of aural detectability. Community noise intrusion and opportunities for AWD optimization were also investigated. Measurements ...

Use of computed tomography to define a sacral safe corridor for placement of 2.7 mm cortical screws in feline sacroiliac luxation.

PubMed

Philp, Helen; Durand, Alexane; De Vicente, Felipe

2018-06-01

Objectives This study aimed to define a safe corridor for 2.7 mm cortical sacroiliac screw insertion in the dorsal plane (craniocaudal direction) using radiography and CT, and in the transverse plane (dorsoventral direction) using CT in feline cadavers. A further aim was to compare the values obtained by CT with those previously reported by radiography in the transverse plane. Methods Thirteen pelvises were retrieved from feline cadavers and dissected to expose one of the articular surfaces of the sacrum. A 2.7 mm screw was placed in the sacrum to a depth of approximately 1 cm in each exposed articular surface. Dorsoventral radiography and CT scanning of each specimen were performed. Multiplanar reconstructions were performed to allow CT evaluation in both the dorsal and transverse planes. Calculations were made to find the maximum, minimum and optimum angles for screw placement in craniocaudal (radiography and CT) and dorsoventral (CT) directions when using a 2.7 mm cortical screw. Results Radiographic measurement showed a mean optimum craniocaudal angle of 106° (range 97-112°). The mean minimum angle was 95° (range 87-107°), whereas the mean maximum angle was 117° (108-124°). Measurement of the dorsal CT scan images showed a mean optimum craniocaudal angle of 101° (range 94-110°). The mean minimum angle was 90° (range 83-99°), whereas the mean maximum angle was 113° (104-125°). The transverse CT scan images showed a mean dorsoventral minimum angle of 103° (range 95-113°), mean maximum angle of 115° (104-125°) and mean optimum dorsoventral angle of 111° (102-119°). Conclusions and relevance An optimum craniocaudal angle of 101° is recommended for 2.7 mm cortical screw placement in the feline sacral body, with a safety margin between 99° and 104°. No single angle can be recommended in the dorsoventral direction and therefore preoperative measuring on individual cats using CT images is recommended to establish the ideal individual angle in the transverse plane.

The effects of decreased audibility produced by high-pass noise masking on cortical event-related potentials to speech sounds/ba/and/da.

PubMed

Martin, B A; Sigal, A; Kurtzberg, D; Stapells, D R

1997-03-01

This study investigated the effects of decreased audibility produced by high-pass noise masking on cortical event-related potentials (ERPs) N1, N2, and P3 to the speech sounds /ba/and/da/presented at 65 and 80 dB SPL. Normal-hearing subjects pressed a button in response to the deviant sound in an oddball paradigm. Broadband masking noise was presented at an intensity sufficient to completely mask the response to the 65-dB SPL speech sounds, and subsequently high-pass filtered at 4000, 2000, 1000, 500, and 250 Hz. With high-pass masking noise, pure-tone behavioral thresholds increased by an average of 38 dB at the high-pass cutoff and by 50 dB one octave above the cutoff frequency. Results show that as the cutoff frequency of the high-pass masker was lowered, ERP latencies to speech sounds increased and amplitudes decreased. The cutoff frequency where these changes first occurred and the rate of the change differed for N1 compared to N2, P3, and the behavioral measures. N1 showed gradual changes as the masker cutoff frequency was lowered. N2, P3, and behavioral measures showed marked changes below a masker cutoff of 2000 Hz. These results indicate that the decreased audibility resulting from the noise masking affects the various ERP components in a differential manner. N1 is related to the presence of audible stimulus energy, being present whether audible stimuli are discriminable or not. In contrast, N2 and P3 were absent when the stimuli were audible but not discriminable (i.e., when the second formant transitions were masked), reflecting stimulus discrimination. These data have implications regarding the effects of decreased audibility on cortical processing of speech sounds and for the study of cortical ERPs in populations with hearing impairment.

Audible sonar images generated with proprioception for target analysis.

PubMed

Kuc, Roman B

2017-05-01

Some blind humans have demonstrated the ability to detect and classify objects with echolocation using palatal clicks. An audible-sonar robot mimics human click emissions, binaural hearing, and head movements to extract interaural time and level differences from target echoes. Targets of various complexity are examined by transverse displacements of the sonar and by target pose rotations that model movements performed by the blind. Controlled sonar movements executed by the robot provide data that model proprioception information available to blind humans for examining targets from various aspects. The audible sonar uses this sonar location and orientation information to form two-dimensional target images that are similar to medical diagnostic ultrasound tomograms. Simple targets, such as single round and square posts, produce distinguishable and recognizable images. More complex targets configured with several simple objects generate diffraction effects and multiple reflections that produce image artifacts. The presentation illustrates the capabilities and limitations of target classification from audible sonar images.

The importance of laughing in your face: influences of visual laughter on auditory laughter perception.

PubMed

Jordan, Timothy R; Abedipour, Lily

2010-01-01

Hearing the sound of laughter is important for social communication, but processes contributing to the audibility of laughter remain to be determined. Production of laughter resembles production of speech in that both involve visible facial movements accompanying socially significant auditory signals. However, while it is known that speech is more audible when the facial movements producing the speech sound can be seen, similar visual enhancement of the audibility of laughter remains unknown. To address this issue, spontaneously occurring laughter was edited to produce stimuli comprising visual laughter, auditory laughter, visual and auditory laughter combined, and no laughter at all (either visual or auditory), all presented in four levels of background noise. Visual laughter and no-laughter stimuli produced very few reports of auditory laughter. However, visual laughter consistently made auditory laughter more audible, compared to the same auditory signal presented without visual laughter, resembling findings reported previously for speech.

Quantification of the effects of audible rattle and source type on the human response to environmental vibration.

PubMed

Woodcock, J; Sica, G; Peris, E; Sharp, C; Moorhouse, A T; Waddington, D C

2016-03-01

The present research quantifies the influence of source type and the presence of audible vibration-induced rattle on annoyance caused by vibration in residential environments. The sources of vibration considered are railway and the construction of a light rail system. Data were measured in the United Kingdom using a socio-vibration survey (N = 1281). These data are analyzed using ordinal logit models to produce exposure-response relationships describing community annoyance as a function of vibration exposure. The influence of source type and the presence of audible vibration-induced rattle on annoyance are investigated using dummy variable analysis, and quantified using odds-ratios and community tolerance levels. It is concluded that the sample population is more likely to express higher levels of annoyance if the vibration source is construction compared to railway, and if vibration-induced rattle is audible.

COMAP: a new computational interpretation of human movement planning level based on coordinated minimum angle jerk policies and six universal movement elements.

PubMed

Emadi Andani, Mehran; Bahrami, Fariba

2012-10-01

Flash and Hogan (1985) suggested that the CNS employs a minimum jerk strategy when planning any given movement. Later, Nakano et al. (1999) showed that minimum angle jerk predicts the actual arm trajectory curvature better than the minimum jerk model. Friedman and Flash (2009) confirmed this claim. Besides the behavioral support that we will discuss, we will show that this model allows simplicity in planning any given movement. In particular, we prove mathematically that each movement that satisfies the minimum joint angle jerk condition is reproducible by a linear combination of six functions. These functions are calculated independent of the type of the movement and are normalized in the time domain. Hence, we call these six universal functions the Movement Elements (ME). We also show that the kinematic information at the beginning and end of the movement determines the coefficients of the linear combination. On the other hand, in analyzing recorded data from sit-to-stand (STS) transfer, arm-reaching movement (ARM) and gait, we observed that minimum joint angle jerk condition is satisfied only during different successive phases of these movements and not for the entire movement. Driven by these observations, we assumed that any given ballistic movement may be decomposed into several successive phases without overlap, such that for each phase the minimum joint angle jerk condition is satisfied. At the boundaries of each phase the angular acceleration of each joint should obtain its extremum (zero third derivative). As a consequence, joint angles at each phase will be linear combinations of the introduced MEs. Coefficients of the linear combination at each phase are the values of the joint kinematics at the boundaries of that phase. Finally, we conclude that these observations may constitute the basis of a computational interpretation, put differently, of the strategy used by the Central Nervous System (CNS) for motor planning. We call this possible interpretation "Coordinated Minimum Angle jerk Policy" or COMAP. Based on this policy, the function of the CNS in generating the desired pattern of any given task (like STS, ARM or gait) can be described computationally using three factors: (1) the kinematics of the motor system at given body states, i.e., at certain movement events/instances, (2) the time length of each phase, and (3) the proposed MEs. From a computational point of view, this model significantly simplifies the processes of movement planning as well as feature abstraction for saving characterizing information of any given movement in memory. Copyright © 2012 Elsevier B.V. All rights reserved.

Remote Infrared Audible Signage (RIAS) Pilot Program : evaluation report

DOT National Transportation Integrated Search

2009-09-01

This report presents evaluation findings on the Remote Infrared Audible Signage (RIAS) Pilot Program in the Puget Sound Region of Washington. The installation, demonstration and evaluation of RIAS were required by a provision in the Safe, Accountable...

76 FR 17613 - Aviation Service Regulations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-30

...) regarding audio visual warning systems (AVWS). OCAS, Inc. installs such technology under the trademark OCAS... frequencies to activate obstruction lighting and transmit audible warnings to aircraft on a potential... transmit audible warnings to pilots. We seek comment on operational, licensing, eligibility and equipment...

The rodent ultrasound production mechanism.

PubMed

Roberts, L H

1975-03-01

Rodents produce two types of sounds, audible and ultrasonic, that differ markedly in physical structure. Studies of sound production in light gases show that whereas the audible cries appear to be produced, as in the case of most other mammals, by vibrating structures in the larynx, the ultrasonic cries are produced by a different mechanism, probably a whistle. 'Bird-call' whistles are shown to have all the properties of rodent ultrasonic cries and to mimic them in almost every detail. Thus it is concluded that rodents have two distinct sound production mechanisms, one for audible cries and one for ultrasonic cries.

Audible sound treatment of the microalgae Picochlorum oklahomensis for enhancing biomass productivity.

PubMed

Cai, Weiming; Dunford, Nurhan Turgut; Wang, Ning; Zhu, Songming; He, Huinong

2016-02-01

It has been reported in the literature that exposure of microalgae cells to audible sound could promote growth. This study examined the effect of sound waves with the frequency of 1100 Hz, 2200 Hz, and 3300 Hz to stimulate the biomass productivity of an Oklahoma native strain, Picochlorum oklahomensis (PO). The effect of the frequency of sound on biomass mass was measured. This study demonstrated that audible sound treatment of the algae cultures at 2200 Hz was the most effective in terms of biomass production and volumetric oil yield. Copyright © 2015 Elsevier Ltd. All rights reserved.

Self-Assessed Hearing Handicap in Older Adults With Poorer-Than-Predicted Speech Recognition in Noise.

PubMed

Eckert, Mark A; Matthews, Lois J; Dubno, Judy R

2017-01-01

Even older adults with relatively mild hearing loss report hearing handicap, suggesting that hearing handicap is not completely explained by reduced speech audibility. We examined the extent to which self-assessed ratings of hearing handicap using the Hearing Handicap Inventory for the Elderly (HHIE; Ventry & Weinstein, 1982) were significantly associated with measures of speech recognition in noise that controlled for differences in speech audibility. One hundred sixty-two middle-aged and older adults had HHIE total scores that were significantly associated with audibility-adjusted measures of speech recognition for low-context but not high-context sentences. These findings were driven by HHIE items involving negative feelings related to communication difficulties that also captured variance in subjective ratings of effort and frustration that predicted speech recognition. The average pure-tone threshold accounted for some of the variance in the association between the HHIE and audibility-adjusted speech recognition, suggesting an effect of central and peripheral auditory system decline related to elevated thresholds. The accumulation of difficult listening experiences appears to produce a self-assessment of hearing handicap resulting from (a) reduced audibility of stimuli, (b) declines in the central and peripheral auditory system function, and (c) additional individual variation in central nervous system function.

Self-Assessed Hearing Handicap in Older Adults With Poorer-Than-Predicted Speech Recognition in Noise

PubMed Central

Matthews, Lois J.; Dubno, Judy R.

2017-01-01

Purpose Even older adults with relatively mild hearing loss report hearing handicap, suggesting that hearing handicap is not completely explained by reduced speech audibility. Method We examined the extent to which self-assessed ratings of hearing handicap using the Hearing Handicap Inventory for the Elderly (HHIE; Ventry & Weinstein, 1982) were significantly associated with measures of speech recognition in noise that controlled for differences in speech audibility. Results One hundred sixty-two middle-aged and older adults had HHIE total scores that were significantly associated with audibility-adjusted measures of speech recognition for low-context but not high-context sentences. These findings were driven by HHIE items involving negative feelings related to communication difficulties that also captured variance in subjective ratings of effort and frustration that predicted speech recognition. The average pure-tone threshold accounted for some of the variance in the association between the HHIE and audibility-adjusted speech recognition, suggesting an effect of central and peripheral auditory system decline related to elevated thresholds. Conclusion The accumulation of difficult listening experiences appears to produce a self-assessment of hearing handicap resulting from (a) reduced audibility of stimuli, (b) declines in the central and peripheral auditory system function, and (c) additional individual variation in central nervous system function. PMID:28060993

The effect of weight and drag on the sinking speed and lift/drag ratio of gliders

NASA Technical Reports Server (NTRS)

Kosin, R

1934-01-01

The most important factors in evaluating performance of gliders are minimum sinking speed and minimum gliding angle. To assure their optimum value the energy necessary for flight, that is, the energy of lift and friction must be kept very low, or in other words, weight and total drag which have a decisive effect on the sinking speed and on the gliding angle, must be kept to a minimum. How great the effect of a reduction of these two quantities will be shown in the following.

49 CFR Table 1 of Subpart B to... - Minimum Coefficient of Retroreflection (RA) (in Candela/Lux/Meter2) Requirement for...

Code of Federal Regulations, 2012 CFR

2012-10-01

...) 1 Table 1 of Subpart B to Part 224 Transportation Other Regulations Relating to Transportation... ROLLING STOCK Pt. 224, Subpt. B, Table 1 Table 1 of Subpart B to Part 224—Minimum Coefficient of... Performance Requirements) Entrance angle Observation angle 0.2 Degree Yellow or fluorescent yellow White 0.5...

49 CFR Table 1 of Subpart B to... - Minimum Coefficient of Retroreflection (RA) (in Candela/Lux/Meter2) Requirement for...

Code of Federal Regulations, 2011 CFR

2011-10-01

...) 1 Table 1 of Subpart B to Part 224 Transportation Other Regulations Relating to Transportation... ROLLING STOCK Pt. 224, Subpt. B, Table 1 Table 1 of Subpart B to Part 224—Minimum Coefficient of... Performance Requirements) Entrance angle Observation angle 0.2 Degree Yellow or fluorescent yellow White 0.5...

Objective measures of binaural masking level differences and comodulation masking release based on late auditory evoked potentials.

PubMed

Epp, Bastian; Yasin, Ifat; Verhey, Jesko L

2013-12-01

The audibility of important sounds is often hampered due to the presence of other masking sounds. The present study investigates if a correlate of the audibility of a tone masked by noise is found in late auditory evoked potentials measured from human listeners. The audibility of the target sound at a fixed physical intensity is varied by introducing auditory cues of (i) interaural target signal phase disparity and (ii) coherent masker level fluctuations in different frequency regions. In agreement with previous studies, psychoacoustical experiments showed that both stimulus manipulations result in a masking release (i: binaural masking level difference; ii: comodulation masking release) compared to a condition where those cues are not present. Late auditory evoked potentials (N1, P2) were recorded for the stimuli at a constant masker level, but different signal levels within the same set of listeners who participated in the psychoacoustical experiment. The data indicate differences in N1 and P2 between stimuli with and without interaural phase disparities. However, differences for stimuli with and without coherent masker modulation were only found for P2, i.e., only P2 is sensitive to the increase in audibility, irrespective of the cue that caused the masking release. The amplitude of P2 is consistent with the psychoacoustical finding of an addition of the masking releases when both cues are present. Even though it cannot be concluded where along the auditory pathway the audibility is represented, the P2 component of auditory evoked potentials is a candidate for an objective measure of audibility in the human auditory system. Copyright © 2013 Elsevier B.V. All rights reserved.

Audible and infrasonic noise levels in the cabins of modern agricultural tractors--does the risk of adverse, exposure-dependent effects still exist?

PubMed

Bilski, Bartosz

2013-06-01

The agricultural tractor is one of the most commonly used vehicles on farms and one of the most prominent sources of noise. This article presents an exemplary assessment of the audible and infrasonic noise levels in the cabins of selected modern wheeled agricultural tractors. Operator-perceived audible and infrasonic noise levels in the cabins were examined for 20 types of modern tractors during typical conditions of work. The tractors had been in use for no longer than 3 years, with rated power between 96 kW and 227 kW, designed and produced by world-renowned companies. Noise level measurements were performed in accordance with PN-EN ISO 9612:2011 (ISO 9612:2009). Audible noise levels (A-weighted) ranged from 62.1 to 87.4 dB-A (average: 68.2 to 83.8 dB-A) for different work tasks. The factors influencing noise levels include performed tasks, soil, weather conditions and the skills of individual drivers. In spectrum analysis, the highest noise levels occurred at frequencies 250 Hz, 1 and 2 kHz. Infrasound noise levels (G-weighted) ranged from 87.3 to 111.3 dB-G. The driver-experienced exposure to infrasound was found to increase significantly when the vehicle was in motion. Average audible noise levels have no potential to adversely affect the hearing organ during tasks performed inside the closed cabins of the analysed modern agricultural tractors. Due to the relatively low audible noise levels inside the cabins of modern agricultural tractors, non-auditory effects are the only adverse symptoms that can develop. Modern agricultural tractors emit considerable infrasonic noise levels. All tractors introduced into the market should be subjected to tests with regard to infrasonic noise levels.

Modern prescription theory and application: realistic expectations for speech recognition with hearing AIDS.

PubMed

Johnson, Earl E

2013-01-01

A major decision at the time of hearing aid fitting and dispensing is the amount of amplification to provide listeners (both adult and pediatric populations) for the appropriate compensation of sensorineural hearing impairment across a range of frequencies (e.g., 160-10000 Hz) and input levels (e.g., 50-75 dB sound pressure level). This article describes modern prescription theory for hearing aids within the context of a risk versus return trade-off and efficient frontier analyses. The expected return of amplification recommendations (i.e., generic prescriptions such as National Acoustic Laboratories-Non-Linear 2, NAL-NL2, and Desired Sensation Level Multiple Input/Output, DSL m[i/o]) for the Speech Intelligibility Index (SII) and high-frequency audibility were traded against a potential risk (i.e., loudness). The modeled performance of each prescription was compared one with another and with the efficient frontier of normal hearing sensitivity (i.e., a reference point for the most return with the least risk). For the pediatric population, NAL-NL2 was more efficient for SII, while DSL m[i/o] was more efficient for high-frequency audibility. For the adult population, NAL-NL2 was more efficient for SII, while the two prescriptions were similar with regard to high-frequency audibility. In terms of absolute return (i.e., not considering the risk of loudness), however, DSL m[i/o] prescribed more outright high-frequency audibility than NAL-NL2 for either aged population, particularly, as hearing loss increased. Given the principles and demonstrated accuracy of desensitization (reduced utility of audibility with increasing hearing loss) observed at the group level, additional high-frequency audibility beyond that of NAL-NL2 is not expected to make further contributions to speech intelligibility (recognition) for the average listener.

An audible automobile back-up pedestrian warning device--development and evaluation

DOT National Transportation Integrated Search

1976-11-01

The purpose of the study was to develop and field-test an audible back-up warning device for use on automobiles. Detailed criteria of pedestrian age and hearing ability combined with noise characteristics of typical accident sites provide the basis f...

Audibility threshold spectrum for prominent discrete tone analysis

NASA Astrophysics Data System (ADS)

Kimizuka, Ikuo

2005-09-01

To evaluate the annoyance of tonal components in noise emissions, ANSI S1.13 (for general purposes) and/or ISO 7779/ECMA-74 (dedicatedfor IT equipment) state two similar metrics: tone-to-noise ratio (TNR) and prominence ratio(PR). By these or either of these two parameters, noise of question with a sharp spectral peak is analyzed by high resolution FFF and classified as prominent when it exceeds some criterion curve. According to present procedures, however this designation is dependent on only the spectral shape. To resolve this problem, the author proposes a threshold spectrum of human ear audibility. The spectrum is based on the reference threshold of hearing which is defined in ISO 389-7 and/or ISO 226. With this spectrum, one can objectively define whether the noise peak of question is audible or not, by simple comparison of the peak amplitude of noise emission and the corresponding value of threshold. Applying the threshold, one can avoid overkilling or unnecessary action for noise. Such a peak with absolutely low amplitude is not audible.

Experimental demonstrations in audible frequency range of band gap tunability and negative refraction in two-dimensional sonic crystal.

PubMed

Pichard, Hélène; Richoux, Olivier; Groby, Jean-Philippe

2012-10-01

The propagation of audible acoustic waves in two-dimensional square lattice tunable sonic crystals (SC) made of square cross-section infinitely rigid rods embedded in air is investigated experimentally. The band structure is calculated with the plane wave expansion (PWE) method and compared with experimental measurements carried out on a finite extend structure of 200 cm width, 70 cm depth and 15 cm height. The structure is made of square inclusions of 5 cm side with a periodicity of L = 7.5 cm placed inbetween two rigid plates. The existence of tunable complete band gaps in the audible frequency range is demonstrated experimentally by rotating the scatterers around their vertical axis. Negative refraction is then analyzed by use of the anisotropy of the equi-frequency surface (EFS) in the first band and of a finite difference time domain (FDTD) method. Experimental results finally show negative refraction in the audible frequency range.

The effects of limited bandwidth and noise on verbal processing time and word recall in normal-hearing children.

PubMed

McCreery, Ryan W; Stelmachowicz, Patricia G

2013-09-01

Understanding speech in acoustically degraded environments can place significant cognitive demands on school-age children who are developing the cognitive and linguistic skills needed to support this process. Previous studies suggest the speech understanding, word learning, and academic performance can be negatively impacted by background noise, but the effect of limited audibility on cognitive processes in children has not been directly studied. The aim of the present study was to evaluate the impact of limited audibility on speech understanding and working memory tasks in school-age children with normal hearing. Seventeen children with normal hearing between 6 and 12 years of age participated in the present study. Repetition of nonword consonant-vowel-consonant stimuli was measured under conditions with combinations of two different signal to noise ratios (SNRs; 3 and 9 dB) and two low-pass filter settings (3.2 and 5.6 kHz). Verbal processing time was calculated based on the time from the onset of the stimulus to the onset of the child's response. Monosyllabic word repetition and recall were also measured in conditions with a full bandwidth and 5.6 kHz low-pass cutoff. Nonword repetition scores decreased as audibility decreased. Verbal processing time increased as audibility decreased, consistent with predictions based on increased listening effort. Although monosyllabic word repetition did not vary between the full bandwidth and 5.6 kHz low-pass filter condition, recall was significantly poorer in the condition with limited bandwidth (low pass at 5.6 kHz). Age and expressive language scores predicted performance on word recall tasks, but did not predict nonword repetition accuracy or verbal processing time. Decreased audibility was associated with reduced accuracy for nonword repetition and increased verbal processing time in children with normal hearing. Deficits in free recall were observed even under conditions where word repetition was not affected. The negative effects of reduced audibility may occur even under conditions where speech repetition is not impacted. Limited stimulus audibility may result in greater cognitive effort for verbal rehearsal in working memory and may limit the availability of cognitive resources to allocate to working memory and other processes.

Ergonomic audit of a specially engineered sonic powered toothbrush with unique sensing and control technologies, the Sonicare Flexcare, and the Oral-B Smart Series 5000.

PubMed

Hunter, Gail; Burns, Laurie; Bone, Brian; Mintel, Thomas; Jimenez, Eduardo

2012-01-01

The presence of ergonomic features can impact the marketplace success of a new product. Metaphase Design Group, Inc., in partnership with the Colgate-Palmolive Company, conducted an ergonomic audit on three electric toothbrushes: a specially engineered sonic powered toothbrush with unique sensing and control technologies, the Sonicare FlexCare, and the Oral-B Smart Series 5000. The ergonomic audit was conducted by Metaphase Design Groups's ergonomic and usability experts. Two experts used the toothbrushes over a one-week period and assessed the performance of each brush against a set of ergonomic principles. The three toothbrushes have some solid ergonomic features. They each have adequate grip zones, provide grip security with elastomeric materials, and provide easy access to the on/off button. The most distinctive feature is the longitudinal shape of the handle of the specially engineered sonic powered toothbrush with unique sensing and control technologies. This handle angles downward at the top end and provides additional advantages through improved grip security and visibility. Yet all three toothbrushes have different opportunities for improvement. The Sonicare Flex Care toothbrush has a cluttered and complicated user interface that is difficult to read. The disadvantages of the Oral-B Smart Series 5000 toothbrush are related to its physical dimensions and audible feedback. The specially engineered sonic powered toothbrush with unique sensing afid control technologies is surprising to use with its changes in speeds, brush movements, and resulting changes in audible feedback.

P-Wave to Rayleigh-wave conversion coefficients for wedge corners; model experiments

USGS Publications Warehouse

Gangi, A.F.; Wesson, R.L.

1978-01-01

An analytic solution is not available for the diffraction of elastic waves by wedges; however, numerical solutions of finite-difference type are available for selected wedge angles. The P- to Rayleigh-wave conversion coefficients at wedge tips have been measured on two-dimensional seismic models for stress-free wedges with wedge angles, ??0, of 10, 30, 60, 90 and 120??. The conversion coefficients show two broad peaks and a minimum as a function of the angle between the wedge face and the direction of the incident P-wave. The minimum occurs for the P wave incident parallel to the wedge face and one maximum is near an incidence angle of 90?? to the wedge face. The amplitude of this maximum, relative to the other, decreases as the wedge angle increases. The asymmetry of the conversion coefficients, CPR(??; ??0), relative to parallel incidence (?? = 0) increases as the wedge angle increases. The locations of the maxima and the minimum as well as the asymmetry can be explained qualitatively. The conversion coefficients are measured with an accuracy of ??5% in those regions where there are no interfering waves. A comparison of the data for the 10?? wedge with the theoretical results for a half plane (0?? wedge) shows good correlation. ?? 1978.

Analysis and Design of Launch Vehicle Flight Control Systems

NASA Technical Reports Server (NTRS)

Wie, Bong; Du, Wei; Whorton, Mark

2008-01-01

This paper describes the fundamental principles of launch vehicle flight control analysis and design. In particular, the classical concept of "drift-minimum" and "load-minimum" control principles is re-examined and its performance and stability robustness with respect to modeling uncertainties and a gimbal angle constraint is discussed. It is shown that an additional feedback of angle-of-attack or lateral acceleration can significantly improve the overall performance and robustness, especially in the presence of unexpected large wind disturbance. Non-minimum-phase structural filtering of "unstably interacting" bending modes of large flexible launch vehicles is also shown to be effective and robust.

46 CFR 154.804 - Vacuum protection.

Code of Federal Regulations, 2013 CFR

2013-10-01

... FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo Vent.... (2) There must be a pressure switch that operates an audible and visual alarm in the cargo control station identifying the tank and the alarm condition and a remote group audible and visual alarm in the...

46 CFR 154.804 - Vacuum protection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo Vent.... (2) There must be a pressure switch that operates an audible and visual alarm in the cargo control station identifying the tank and the alarm condition and a remote group audible and visual alarm in the...

46 CFR 154.804 - Vacuum protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo Vent.... (2) There must be a pressure switch that operates an audible and visual alarm in the cargo control station identifying the tank and the alarm condition and a remote group audible and visual alarm in the...

Application of TrackEye in equine locomotion research.

PubMed

Drevemo, S; Roepstorff, L; Kallings, P; Johnston, C J

1993-01-01

TrackEye is an analysis system, which is applicable for equine biokinematic studies. It covers the whole process from digitizing of images, automatic target tracking and analysis. Key components in the system are an image work station for processing of video images and a high-resolution film-to-video scanner for 16-mm film. A recording module controls the input device and handles the capture of image sequences into a videodisc system, and a tracking module is able to follow reference markers automatically. The system offers a flexible analysis including calculations of markers displacements, distances and joint angles, velocities and accelerations. TrackEye was used to study effects of phenylbutazone on the fetlock and carpal joint angle movements in a horse with a mild lameness caused by osteo-arthritis in the fetlock joint of a forelimb. Significant differences, most evident before treatment, were observed in the minimum fetlock and carpal joint angles when contralateral limbs were compared (p < 0.001). The minimum fetlock angle and the minimum carpal joint angle were significantly greater in the lame limb before treatment compared to those 6, 37 and 49 h after the last treatment (p < 0.001).

Pars plana Ahmed valve and vitrectomy in patients with glaucoma associated with posterior segment disease.

PubMed

Wallsh, Josh O; Gallemore, Ron P; Taban, Mehran; Hu, Charles; Sharareh, Behnam

2013-01-01

To assess the safety and efficacy of a modified technique for pars plana placement of the Ahmed valve in combination with pars plana vitrectomy in the treatment of glaucoma associated with posterior segment disease. Thirty-nine eyes with glaucoma associated with posterior segment disease underwent pars plana vitrectomy combined with Ahmed valve placement. All valves were placed in the pars plana using a modified technique, without the pars plana clip, and using a scleral patch graft. The 24 eyes diagnosed with neovascular glaucoma had an improvement in intraocular pressure from 37.6 mmHg to 13.8 mmHg and best-corrected visual acuity from 2.13 logarithm of minimum angle of resolution to 1.40 logarithm of minimum angle of resolution. Fifteen eyes diagnosed with steroid-induced glaucoma had an improvement in intraocular pressure from 27.9 mmHg to 14.1 mmHg and best-corrected visual acuity from 1.38 logarithm of minimum angle of resolution to 1.13 logarithm of minimum angle of resolution. Complications included four cases of cystic bleb formation and one case of choroidal detachment and explantation for hypotony. Ahmed valve placement through the pars plana during vitrectomy is an effective option for managing complex cases of glaucoma without the use of the pars plana clip.

49 CFR 214.511 - Required audible warning devices for new on-track roadway maintenance machines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... roadway maintenance machines. 214.511 Section 214.511 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.511 Required audible warning devices for new on-track roadway maintenance machines. Each new on-track roadway maintenance machine shall...

49 CFR 214.511 - Required audible warning devices for new on-track roadway maintenance machines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... roadway maintenance machines. 214.511 Section 214.511 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.511 Required audible warning devices for new on-track roadway maintenance machines. Each new on-track roadway maintenance machine shall...

33 CFR 86.05 - Sound signal intensity and range of audibility.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Sound signal intensity and range... HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Whistles § 86.05 Sound signal intensity and range of audibility. A whistle on a vessel shall provide, in the...

33 CFR 86.05 - Sound signal intensity and range of audibility.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Sound signal intensity and range... HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Whistles § 86.05 Sound signal intensity and range of audibility. A whistle on a vessel shall provide, in the...

33 CFR 86.05 - Sound signal intensity and range of audibility.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Sound signal intensity and range... HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Whistles § 86.05 Sound signal intensity and range of audibility. A whistle on a vessel shall provide, in the...

Audible Conversational Affordances and Constraints of Verbalizing Professional Noticing during Prospective Teacher Lesson Study

ERIC Educational Resources Information Center

Amador, Julie M.; Carter, Ingrid S.

2018-01-01

Lesson Study, which assumes multiple variations, is a collaborative method that provides an opportunity for teachers to notice professionally. We analyzed how audible conversational components afforded and constrained the verbalization of professional noticing of a lesson study team. The team, comprised of six prospective teachers, a classroom…

Modern Prescription Theory and Application: Realistic Expectations for Speech Recognition With Hearing Aids

PubMed Central

2013-01-01

A major decision at the time of hearing aid fitting and dispensing is the amount of amplification to provide listeners (both adult and pediatric populations) for the appropriate compensation of sensorineural hearing impairment across a range of frequencies (e.g., 160–10000 Hz) and input levels (e.g., 50–75 dB sound pressure level). This article describes modern prescription theory for hearing aids within the context of a risk versus return trade-off and efficient frontier analyses. The expected return of amplification recommendations (i.e., generic prescriptions such as National Acoustic Laboratories—Non-Linear 2, NAL-NL2, and Desired Sensation Level Multiple Input/Output, DSL m[i/o]) for the Speech Intelligibility Index (SII) and high-frequency audibility were traded against a potential risk (i.e., loudness). The modeled performance of each prescription was compared one with another and with the efficient frontier of normal hearing sensitivity (i.e., a reference point for the most return with the least risk). For the pediatric population, NAL-NL2 was more efficient for SII, while DSL m[i/o] was more efficient for high-frequency audibility. For the adult population, NAL-NL2 was more efficient for SII, while the two prescriptions were similar with regard to high-frequency audibility. In terms of absolute return (i.e., not considering the risk of loudness), however, DSL m[i/o] prescribed more outright high-frequency audibility than NAL-NL2 for either aged population, particularly, as hearing loss increased. Given the principles and demonstrated accuracy of desensitization (reduced utility of audibility with increasing hearing loss) observed at the group level, additional high-frequency audibility beyond that of NAL-NL2 is not expected to make further contributions to speech intelligibility (recognition) for the average listener. PMID:24253361

Exposure to audible and infrasonic noise by modern agricultural tractors operators.

PubMed

Bilski, Bartosz

2013-03-01

The wheeled agricultural tractor is one of the most prominent sources of noise in agriculture. This paper presents the assessment of the operator's exposure to audible and infrasonic noise in 32 selected modern wheeled agricultural tractors designed and produced by world-renowned companies in normal working conditions. The tractors have been in use for no longer than 4 years, with rated power of 51 kW to up to 228 kW (as per 97/68 EC). Audible and infrasonic noise level measurements and occupational exposure analysis to noise were performed according to ISO 9612:2009 (strategy 1 - task-based measurements). The measurements were made in different typical work conditions inside and outside of tractors cabs. The results indicated that exposure levels to noise perceived by the operators (L(ex,Te) between 62,3 and 84,7 dB-A) and can make a small risk of potential adversely effects on hearing during tasks performed inside the closed cab. It should be remarked that uncertainty interval is wider and in in some conditions can occur transgression of audible noise occupational exposure limits. The measured audible noise levels can potentially develop the non-auditory effects. Analysed tractors emit considerable infrasonic noise levels that tend to exceed the occupational exposure limits (both inside and outside the driver's cab). The levels of infrasound: 83,8-111,4 dB-G. All tractors introduced for sale should be subjected to tests in terms of infrasonic noise levels. The applicable standards for low frequency noise and its measurement methods for vehicles, including agricultural tractors, should be scientifically revised. In the last years there has been a noticeable technical progress in reduction of audible noise exposure at the tractors operators workplaces with simultaneously lack of important works for limitation of exposure to infrasound. Author discuss possible health and ergonomic consequencies of such exposure. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Modeling contact angle hysteresis of a liquid droplet sitting on a cosine wave-like pattern surface.

PubMed

Promraksa, Arwut; Chen, Li-Jen

2012-10-15

A liquid droplet sitting on a hydrophobic surface with a cosine wave-like square-array pattern in the Wenzel state is simulated by using the Surface Evolver to determine the contact angle. For a fixed drop volume, multiple metastable states are obtained at two different surface roughnesses. Unusual and non-circular shape of the three-phase contact line of a liquid droplet sitting on the model surface is observed due to corrugation and distortion of the contact line by structure of the roughness. The contact angle varies along the contact line for each metastable state. The maximum and minimum contact angles among the multiple metastable states at a fixed viewing angle correspond to the advancing and the receding contact angles, respectively. It is interesting to observe that the advancing/receding contact angles (and contact angle hysteresis) are a function of viewing angle. In addition, the receding (or advancing) contact angles at different viewing angles are determined at different metastable states. The contact angle of minimum energy among the multiple metastable states is defined as the most stable (equilibrium) contact angle. The Wenzel model is not able to describe the contact angle along the three-phase contact line. The contact angle hysteresis at different drop volumes is determined. The number of the metastable states increases with increasing drop volume. Drop volume effect on the contact angles is also discussed. Crown Copyright © 2012. Published by Elsevier Inc. All rights reserved.

Coupling of Head and Body Movement with Motion of the Audible Environment

ERIC Educational Resources Information Center

Stoffregen, Thomas A.; Villard, Sebastien; Kim, ChungGon; Ito, Kiyohide; Bardy, Benoit G.

2009-01-01

The authors asked whether standing posture could be controlled relative to audible oscillation of the environment. Blindfolded sighted adults were exposed to acoustic flow in a moving room, and were asked to move so as to maintain a constant distance between their head and the room. Acoustic flow had direct (source) and indirect (reflected)…

Use of Audible and Chart-recorded Ultrasonography to Monitor Fetal Heart Rate and Uterine Blood Flow Parameters in Cattle

USDA-ARS?s Scientific Manuscript database

The objective of the present study was to evaluate the use of audible chart-recorded doppler ultrasonography (DUS) to monitor both uterine blood flow and fetal heart rate (FHR) during pregnancy in dairy cattle. Possible applications of DUS include the monitoring of fetal distress when a pregnancy be...

The Use of Audible Traffic Signals in the United States.

ERIC Educational Resources Information Center

Peck, A. F.; Uslan, M.

1990-01-01

This paper discusses audible traffic signals (ATS) and their use by visually impaired pedestrians in the United States and other countries. Areas of concern are noted, including the types of intersections at which ATS should be installed, the locations of poles and buttons for activating the system, and the specific type of device used.…

Bimodal behavior of post-measured entropy and one-way quantum deficit for two-qubit X states

NASA Astrophysics Data System (ADS)

Yurischev, Mikhail A.

2018-01-01

A method for calculating the one-way quantum deficit is developed. It involves a careful study of post-measured entropy shapes. We discovered that in some regions of X-state space the post-measured entropy \\tilde{S} as a function of measurement angle θ \\in [0,π /2] exhibits a bimodal behavior inside the open interval (0,π /2), i.e., it has two interior extrema: one minimum and one maximum. Furthermore, cases are found when the interior minimum of such a bimodal function \\tilde{S}(θ ) is less than that one at the endpoint θ =0 or π /2. This leads to the formation of a boundary between the phases of one-way quantum deficit via finite jumps of optimal measured angle from the endpoint to the interior minimum. Phase diagram is built up for a two-parameter family of X states. The subregions with variable optimal measured angle are around 1% of the total region, with their relative linear sizes achieving 17.5%, and the fidelity between the states of those subregions can be reduced to F=0.968. In addition, a correction to the one-way deficit due to the interior minimum can achieve 2.3%. Such conditions are favorable to detect the subregions with variable optimal measured angle of one-way quantum deficit in an experiment.

Triple innominate osteotomy for Legg-Calvé-Perthes disease in children: does the lateral coverage change with time?

PubMed

Hosalkar, Harish; Munhoz da Cunha, Ana Laura; Baldwin, Keith; Ziebarth, Kai; Wenger, Dennis R

2012-09-01

Triple innominate osteotomy (TIO) is one of the modalities of surgical containment in Legg-Calvé-Perthes disease (LCPD). However, overcoverage with TIO can lead to pincer impingement. We therefore asked (1) whether TIO contained the femoral head in Catterall Stages III and IV of LCPD; (2) whether the center-edge (CE) angle, acetabular roof arc angle (ARA), and Sharp's angle changed during the growing years; and (3) what percentage of patients had radiographic evidence of pincer impingement beyond a minimum followup of 3 years. We identified 19 children who had 20 TIOs performed for Catterall Stages III and IV LCPD. Two blinded observers assessed sequential radiographs. Each observer made two sets of readings more than 2 weeks apart. Femoral head extrusion index, CE angle of Wiberg, ARA, and Sharp's angle were measured. Minimum followup was 3 years to document continued acetabular growth (mean, 3.8 years; range, 3-7 years). All patients exhibited femoral head containment at last followup. Eleven of 20 hips demonstrated no radiographic evidence of pincer morphology beyond a minimum followup of 3 years (mean, 3.8 years). Patients with CE angle corrected to 44° or less and an ARA of greater than -6° after TIO did not demonstrate a pincer morphology at last followup. TIO resulted in femoral head containment in all cases. Lateral acetabular coverage changed during the growing years in all patients. Surgical correction beyond 44° of CE angle and -6° of ARA should be avoided to prevent pincer morphology later.

Audible Image Description as an Accommodation in Statewide Assessments for Students with Visual and Print Disabilities

ERIC Educational Resources Information Center

Ferrell, Kay Alicyn; Correa-Torres, Silvia M.; Howell, Jennifer Johnson; Pearson, Robert; Carver, Wendy Morrow; Groll, Amy Spencer; Anthony, Tanni L.; Matthews, Deborah; Gould, Bryan; O'Connell, Trisha; Botsford, Kathryn D,; Dewald, Hong Phangia; Smyth, Catherine A.; Dewald, Aaron John

2017-01-01

Introduction:Although image description has been identified as an accommodation for presentations conducted in the classroom, only a few U.S. states have approved it for use in high-stakes assessments. This study examined the use of audible image description as an assessment accommodation for students with visual and print disabilities by…

Validity and Reliability of Visual Analog Scaling for Assessment of Hypernasality and Audible Nasal Emission in Children With Repaired Cleft Palate.

PubMed

Baylis, Adriane; Chapman, Kathy; Whitehill, Tara L; Group, The Americleft Speech

2015-11-01

To investigate the validity and reliability of multiple listener judgments of hypernasality and audible nasal emission, in children with repaired cleft palate, using visual analog scaling (VAS) and equal-appearing interval (EAI) scaling. Prospective comparative study of multiple listener ratings of hypernasality and audible nasal emission. Multisite institutional. Five trained and experienced speech-language pathologist listeners from the Americleft Speech Project. Average VAS and EAI ratings of hypernasality and audible nasal emission/turbulence for 12 video-recorded speech samples from the Americleft Speech Project. Intrarater and interrater reliability was computed, as well as linear and polynomial models of best fit. Intrarater and interrater reliability was acceptable for both rating methods; however, reliability was higher for VAS as compared to EAI ratings. When VAS ratings were plotted against EAI ratings, results revealed a stronger curvilinear relationship. The results of this study provide additional evidence that alternate rating methods such as VAS may offer improved validity and reliability over EAI ratings of speech. VAS should be considered a viable method for rating hypernasality and nasal emission in speech in children with repaired cleft palate.

Guitar Strings as Standing Waves: A Demonstration

NASA Astrophysics Data System (ADS)

Davis, Michael

2007-08-01

An undergraduate student's first exposure to modern atomic theory tends to start with Bohr's model of the atom. This familiar introduction to atomic structure also marks a general chemistry student's first foray into waves. Many popular chemistry textbooks illustrate the concept of a standing wave in the development of the modern quantum model by using the phrase “as seen on a guitar string”. In these illustrations, the wave itself is often small and difficult to discern. The same phenomenon, however, can be easily and audibly observed. This demonstration uses an acoustic guitar to produce three unique harmonic vibrations, each of which is representative of a standing wave and illustrates the concept of quantization. Manipulation of the guitar string to produce a standing wave is pervasive in popular music and is audibly recognizable. Lightly placing a finger on the 12th, 7th, or 5th fret and strumming any one or all six strings can produce an audible example of a standing wave on a guitar. This corresponds to a standing wave with 1, 2, or 3 nodes, respectively. Attempting to induce a node at other points on a guitar string does not generate a standing wave, due to destructive interference, thus no audible tone is produced.

Propeller Flaps With Reduced Rotational Angles: Clinical Experience on 40 Consecutive Reconstructions Performed at Different Anatomical Sites.

PubMed

Brunetti, Beniamino; Tenna, Stefania; Poccia, Igor; Persichetti, Paolo

2017-02-01

Despite of the widespread use of 180-degree propeller flaps in the field of soft tissue reconstruction, less information are available in the current literature to standardize the use of propeller flaps with reduced degrees of rotation.The authors report their experience with propeller flaps with reduced rotational angles reviewing clinical applications and outcomes of the technique in a series of 40 consecutive reconstructions. Forty elective defects of various etiologies located in different regions of the body (head and neck, trunk, buttocks and perineum, extremities) were reconstructed with less than 180 degrees rotated propeller flaps. The technique was applied to patients presenting with a strong audible perforator detected in close proximity to the wound and the defect located in a position adjacent to the axis of the chosen perforasome. Defect size ranged from 2 × 2 to 15 × 9 cm. Flap dimensions ranged from 5 × 2 to 21 × 10 cm. The flaps were based on 1 (34) or 2 (6) perforators and were mobilized with an angle of rotation of 45, 90, and 135 degrees in 7, 24, and 9 patients, respectively. Mean operative time was 105 minutes. All flaps survived postoperatively. In only 4 cases (10%) partial flap necrosis was registered. All flaps achieved adequate and durable reconstruction with excellent contour, with a follow-up ranging between 6 months and 2 years. Propeller flaps with reduced rotational angles represent a safe and versatile option to reconstruct soft tissues defects at different anatomical sites.

Effect of Afterbody Length and Keel Angle on Minimum Depth of Step for Landing Stability and on Take-Off Stability of a Flying Boat

NASA Technical Reports Server (NTRS)

Olson, Roland E; Land, Norman S

1949-01-01

Tests were made to fill partly the need for information on the effect of afterbody dimensions on the hydrodynamic stability of a flying boat in smooth water. The dimensions investigated were depth of step, angle of afterbody keel, and length of afterbody. An analysis of the data showed that as either the afterbody length or keel angle was increased an accompanying increase in depth of step was required in order to maintain adequate landing stability. The landing-tests results have been reduced to an empirical formula giving the minimum depth of step in terms of afterbody length and keel angle. This formula is compared with results from other tank tests, and the correlation is fairly good. The formula thus becomes of use in preliminary design.

Intelligent Weather Agent

NASA Technical Reports Server (NTRS)

Spirkovska, Liljana (Inventor)

2006-01-01

Method and system for automatically displaying, visually and/or audibly and/or by an audible alarm signal, relevant weather data for an identified aircraft pilot, when each of a selected subset of measured or estimated aviation situation parameters, corresponding to a given aviation situation, has a value lying in a selected range. Each range for a particular pilot may be a default range, may be entered by the pilot and/or may be automatically determined from experience and may be subsequently edited by the pilot to change a range and to add or delete parameters describing a situation for which a display should be provided. The pilot can also verbally activate an audible display or visual display of selected information by verbal entry of a first command or a second command, respectively, that specifies the information required.

14 CFR 23.149 - Minimum control speed.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Minimum control speed. 23.149 Section 23... Maneuverability § 23.149 Minimum control speed. (a) VMC is the calibrated airspeed at which, when the critical... still inoperative, and thereafter maintain straight flight at the same speed with an angle of bank of...

14 CFR 23.149 - Minimum control speed.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Minimum control speed. 23.149 Section 23... Maneuverability § 23.149 Minimum control speed. (a) VMC is the calibrated airspeed at which, when the critical... still inoperative, and thereafter maintain straight flight at the same speed with an angle of bank of...

Segmental and Suprasegmental Perception in Children Using Hearing Aids.

PubMed

Wenrich, Kaitlyn A; Davidson, Lisa S; Uchanski, Rosalie M

Suprasegmental perception (perception of stress, intonation, "how something is said" and "who says it") and segmental speech perception (perception of individual phonemes or perception of "what is said") are perceptual abilities that provide the foundation for the development of spoken language and effective communication. While there are numerous studies examining segmental perception in children with hearing aids (HAs), there are far fewer studies examining suprasegmental perception, especially for children with greater degrees of residual hearing. Examining the relation between acoustic hearing thresholds, and both segmental and suprasegmental perception for children with HAs, may ultimately enable better device recommendations (bilateral HAs, bimodal devices [one CI and one HA in opposite ears], bilateral CIs) for a particular degree of residual hearing. Examining both types of speech perception is important because segmental and suprasegmental cues are affected differentially by the type of hearing device(s) used (i.e., cochlear implant [CI] and/or HA). Additionally, suprathreshold measures, such as frequency resolution ability, may partially predict benefit from amplification and may assist audiologists in making hearing device recommendations. The purpose of this study is to explore the relationship between audibility (via hearing thresholds and speech intelligibility indices), and segmental and suprasegmental speech perception for children with HAs. A secondary goal is to explore the relationships among frequency resolution ability (via spectral modulation detection [SMD] measures), segmental and suprasegmental speech perception, and receptive language in these same children. A prospective cross-sectional design. Twenty-three children, ages 4 yr 11 mo to 11 yr 11 mo, participated in the study. Participants were recruited from pediatric clinic populations, oral schools for the deaf, and mainstream schools. Audiological history and hearing device information were collected from participants and their families. Segmental and suprasegmental speech perception, SMD, and receptive vocabulary skills were assessed. Correlations were calculated to examine the significance (p < 0.05) of relations between audibility and outcome measures. Measures of audibility and segmental speech perception are not significantly correlated, while low-frequency pure-tone average (unaided) is significantly correlated with suprasegmental speech perception. SMD is significantly correlated with all measures (measures of audibility, segmental and suprasegmental perception and vocabulary). Lastly, although age is not significantly correlated with measures of audibility, it is significantly correlated with all other outcome measures. The absence of a significant correlation between audibility and segmental speech perception might be attributed to overall audibility being maximized through well-fit HAs. The significant correlation between low-frequency unaided audibility and suprasegmental measures is likely due to the strong, predominantly low-frequency nature of suprasegmental acoustic properties. Frequency resolution ability, via SMD performance, is significantly correlated with all outcomes and requires further investigation; its significant correlation with vocabulary suggests that linguistic ability may be partially related to frequency resolution ability. Last, all of the outcome measures are significantly correlated with age, suggestive of developmental effects. American Academy of Audiology

Characteristics of pitch angle distributions of hundreds of keV electrons in the slot region and inner radiation belt

NASA Astrophysics Data System (ADS)

Zhao, H.; Li, X.; Blake, J. B.; Fennell, J. F.; Claudepierre, S. G.; Baker, D. N.; Jaynes, A. N.; Malaspina, D. M.

2014-12-01

The pitch angle distribution (PAD) of energetic electrons in the slot region and inner radiation belt received little attention in the past decades due to the lack of quality measurements. Using the state-of-the-art pitch angle-resolved data from the Magnetic Electron Ion Spectrometer instrument onboard the Van Allen Probes, a detailed analysis of hundreds of keV electron PADs below L = 4 is performed, in which the PADs are categorized into three types: normal (flux peaking at 90°), cap (exceedingly peaking narrowly around 90°), and 90° minimum (lower flux at 90°) PADs. By examining the characteristics of the PADs of ˜460 keV electrons for over a year, we find that the 90° minimum PADs are generally present in the inner belt (L<2), while normal PADs dominate at L˜3.5-4. In the region between, 90° minimum PADs dominate during injection times and normal PADs dominate during quiet times. Cap PADs appear mostly at the decay phase of storms in the slot region and are likely caused by the pitch angle scattering of hiss waves. Fitting the normal PADs into sinnα form, the parameter n is much higher below L = 3 than that in the outer belt and relatively constant in the inner belt but changes significantly in the slot region (2 < L < 3) during injection times. As for the 90° minimum PADs, by performing a detailed case study, we find in the slot region this type of PAD is likely caused by chorus wave heating, but this mechanism can hardly explain the formation of 90° minimum PADs at the center of inner belt.

Optimal link budget to maximize data receiving from remote sensing satellite at different ground stations

NASA Astrophysics Data System (ADS)

Godse, Vinay V.; Rukmini, B.

2016-10-01

Earth observation satellite plays a significant role for global situation awareness. The earth observation satellite uses imaging payloads in RF and IR bands, which carry huge amount of data, needs to be transferred during visibility of satellite over the ground station. Location of ground station plays a very important role in communication with LEO satellites, as orbital speed of LEO satellite is much higher than earth rotation speed. It will be accessible for particular equatorial ground station for a very short duration. In this paper we want to maximize data receiving by optimizing link budget and receiving data at higher elevation links. Data receiving at multiple ground stations is preferred to counter less pass duration due to higher elevation links. Our approach is to calculate link budget for remote sensing satellite with a fixed power input and varying different minimum elevation angles to obtain maximum data. The minimum pass duration should be above 3 minutes for effective communication. We are proposing to start process of command handling as soon as satellite is visible to particular ground station with low elevation angle up to 5 degree and start receiving data at higher elevation angles to receive data with higher speed. Cartosat-2B LEO earth observation satellite is taken for the case study. Cartosat-2B will complete around 14 passes over equator in a day, out of which only 4-5 passes will be useful for near equator ground stations. Our aim is to receive data at higher elevation angles at higher speed and increase amount of data download, criteria being minimum pass duration of 3 minutes, which has been set for selecting minimum elevation angle.

Minimum viewing angle for visually guided ground speed control in bumblebees.

PubMed

Baird, Emily; Kornfeldt, Torill; Dacke, Marie

2010-05-01

To control flight, flying insects extract information from the pattern of visual motion generated during flight, known as optic flow. To regulate their ground speed, insects such as honeybees and Drosophila hold the rate of optic flow in the axial direction (front-to-back) constant. A consequence of this strategy is that its performance varies with the minimum viewing angle (the deviation from the frontal direction of the longitudinal axis of the insect) at which changes in axial optic flow are detected. The greater this angle, the later changes in the rate of optic flow, caused by changes in the density of the environment, will be detected. The aim of the present study is to examine the mechanisms of ground speed control in bumblebees and to identify the extent of the visual range over which optic flow for ground speed control is measured. Bumblebees were trained to fly through an experimental tunnel consisting of parallel vertical walls. Flights were recorded when (1) the distance between the tunnel walls was either 15 or 30 cm, (2) the visual texture on the tunnel walls provided either strong or weak optic flow cues and (3) the distance between the walls changed abruptly halfway along the tunnel's length. The results reveal that bumblebees regulate ground speed using optic flow cues and that changes in the rate of optic flow are detected at a minimum viewing angle of 23-30 deg., with a visual field that extends to approximately 155 deg. By measuring optic flow over a visual field that has a low minimum viewing angle, bumblebees are able to detect and respond to changes in the proximity of the environment well before they are encountered.

Weight compensation characteristics of Armeo®Spring exoskeleton: implications for clinical practice and research.

PubMed

Perry, Bonnie E; Evans, Emily K; Stokic, Dobrivoje S

2017-02-17

Armeo®Spring exoskeleton is widely used for upper extremity rehabilitation; however, weight compensation provided by the device appears insufficiently characterized to fully utilize it in clinical and research settings. Weight compensation was quantified by measuring static force in the sagittal plane with a load cell attached to the elbow joint of Armeo®Spring. All upper spring settings were examined in 5° increments at the minimum, maximum, and two intermediate upper and lower module length settings, while keeping the lower spring at minimum. The same measurements were made for minimum upper spring setting and maximum lower spring setting at minimum and maximum module lengths. Weight compensation was plotted against upper module angles, and slope was analyzed for each condition. The Armeo®Spring design prompted defining the slack angle and exoskeleton balance angle, which, depending on spring and length settings, divide the operating range into different unloading and loading regions. Higher spring tensions and shorter module lengths provided greater unloading (≤6.32 kg of support). Weight compensation slope decreased faster with shorter length settings (minimum length = -0.082 ± 0.002 kg/°; maximum length = -0.046 ± 0.001 kg/°) independent of spring settings. Understanding the impact of different settings on the Armeo®Spring weight compensation should help define best clinical practice and improve fidelity of research.

Application of a simple recording system to the analysis of free-play behavior in autistic children1

PubMed Central

Boer, Arend P.

1968-01-01

An observational system, which has been developed to facilitate recording of the total behavioral repertoire of autistic children, involves time-sampling recording of behavior with the help of a common Stenograph machine. Categories which exhausted all behavior were defined. Each category corresponded with a designated key on the Stenograph machine. The observer depressed one key at each 1-sec interval. The observer was paced by audible beats from a metronome. A naive observer can be used with this method. The observer is not mechanically limited and a minimum of observer training is required to obtain reliable measures. The data sampled during a five-week observation period indicated the stability of a taxonomic instrument of behavior based upon direct, time-sampling observations and the stability of spontaneous autistic behavior. Results showed that the behavior of the subjects was largely nonrandom and unsocialized in character. PMID:16795193

Application of a simple recording system to the analysis of free-play behavior in autistic children.

PubMed

Boer, A P

1968-01-01

An observational system, which has been developed to facilitate recording of the total behavioral repertoire of autistic children, involves time-sampling recording of behavior with the help of a common Stenograph machine. Categories which exhausted all behavior were defined. Each category corresponded with a designated key on the Stenograph machine. The observer depressed one key at each 1-sec interval. The observer was paced by audible beats from a metronome. A naive observer can be used with this method. The observer is not mechanically limited and a minimum of observer training is required to obtain reliable measures. The data sampled during a five-week observation period indicated the stability of a taxonomic instrument of behavior based upon direct, time-sampling observations and the stability of spontaneous autistic behavior. Results showed that the behavior of the subjects was largely nonrandom and unsocialized in character.

16 CFR Table 2 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1 2 Table 2 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION... 1512—Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1 Observation angle Front, rear...

Applications of sub-audible speech recognition based upon electromyographic signals

NASA Technical Reports Server (NTRS)

Jorgensen, C. Charles (Inventor); Betts, Bradley J. (Inventor)

2009-01-01

Method and system for generating electromyographic or sub-audible signals (''SAWPs'') and for transmitting and recognizing the SAWPs that represent the original words and/or phrases. The SAWPs may be generated in an environment that interferes excessively with normal speech or that requires stealth communications, and may be transmitted using encoded, enciphered or otherwise transformed signals that are less subject to signal distortion or degradation in the ambient environment.

Mechanism For Adjustment Of Commutation Of Brushless Motor

NASA Technical Reports Server (NTRS)

Schaefer, Richard E.

1995-01-01

Mechanism enables adjustment of angular position of set of Hall-effect devices that sense instantaneous shaft angle of brushless dc motor. Outputs of sensors fed to commutation circuitry. Measurement of shaft angle essential for commutation; that is, application of voltage to stator windings must be synchronized with shaft angle. To obtain correct angle measurement for commutation, Hall-effect angle sensors positioned at proper reference angle. The present mechanism accelerates adjustment procedure and makes it possible to obtain more accurate indication of minimum-current position because it provides for adjustment while motor running.

Infants' response to the audible and visible properties of the human face: II. Discrimination of differences between singing and adult-directed speech.

PubMed

Lewkowicz, D J

1998-05-01

Human infants' responsiveness to the audible and visible features of human faces was studied by habituating them to a person speaking a prepared script in an adult-directed manner and then administering a series of separate test trials where a person could be seen, heard, or seen and heard singing. When habituated to a female person speaking in an adult-directed manner and tested with a singing female 4, 6, and 8-month-old infants responded to the audible, visible, and bimodal changes, whereas 3-month-old infants only responded to the visual and bimodal changes. In contrast, when habituated to a male person speaking in an adult-directed manner and tested with a singing female, all age groups discriminated all three types of changes. These findings demonstrate that infants are responsive to differences between low- and high-prosody content inherent in both the facial and vocal characteristics of the human face and that, whereas responsiveness to the visible and bimodal features associated with differences between adult-directed speech and singing is present as early as 3 months of age, responsiveness to the audible features emerges between 3 and 4 months of age depending on whether gender differences are present as well.

Cell type-specific suppression of mechanosensitive genes by audible sound stimulation.

PubMed

Kumeta, Masahiro; Takahashi, Daiji; Takeyasu, Kunio; Yoshimura, Shige H

2018-01-01

Audible sound is a ubiquitous environmental factor in nature that transmits oscillatory compressional pressure through the substances. To investigate the property of the sound as a mechanical stimulus for cells, an experimental system was set up using 94.0 dB sound which transmits approximately 10 mPa pressure to the cultured cells. Based on research on mechanotransduction and ultrasound effects on cells, gene responses to the audible sound stimulation were analyzed by varying several sound parameters: frequency, wave form, composition, and exposure time. Real-time quantitative PCR analyses revealed a distinct suppressive effect for several mechanosensitive and ultrasound-sensitive genes that were triggered by sounds. The effect was clearly observed in a wave form- and pressure level-specific manner, rather than the frequency, and persisted for several hours. At least two mechanisms are likely to be involved in this sound response: transcriptional control and RNA degradation. ST2 stromal cells and C2C12 myoblasts exhibited a robust response, whereas NIH3T3 cells were partially and NB2a neuroblastoma cells were completely insensitive, suggesting a cell type-specific response to sound. These findings reveal a cell-level systematic response to audible sound and uncover novel relationships between life and sound.

Cell type-specific suppression of mechanosensitive genes by audible sound stimulation

PubMed Central

Takahashi, Daiji; Takeyasu, Kunio; Yoshimura, Shige H.

2018-01-01

Audible sound is a ubiquitous environmental factor in nature that transmits oscillatory compressional pressure through the substances. To investigate the property of the sound as a mechanical stimulus for cells, an experimental system was set up using 94.0 dB sound which transmits approximately 10 mPa pressure to the cultured cells. Based on research on mechanotransduction and ultrasound effects on cells, gene responses to the audible sound stimulation were analyzed by varying several sound parameters: frequency, wave form, composition, and exposure time. Real-time quantitative PCR analyses revealed a distinct suppressive effect for several mechanosensitive and ultrasound-sensitive genes that were triggered by sounds. The effect was clearly observed in a wave form- and pressure level-specific manner, rather than the frequency, and persisted for several hours. At least two mechanisms are likely to be involved in this sound response: transcriptional control and RNA degradation. ST2 stromal cells and C2C12 myoblasts exhibited a robust response, whereas NIH3T3 cells were partially and NB2a neuroblastoma cells were completely insensitive, suggesting a cell type-specific response to sound. These findings reveal a cell-level systematic response to audible sound and uncover novel relationships between life and sound. PMID:29385174

Apparatus for monitoring X-ray beam alignment

DOEpatents

Steinmeyer, Peter A.

1991-10-08

A self-contained, hand-held apparatus is provided for minitoring alignment of an X-ray beam in an instrument employing an X-ray source. The apparatus includes a transducer assembly containing a photoresistor for providing a range of electrical signals responsive to a range of X-ray beam intensities from the X-ray beam being aligned. A circuit, powered by a 7.5 VDC power supply and containing an audio frequency pulse generator whose frequency varies with the resistance of the photoresistor, is provided for generating a range of audible sounds. A portion of the audible range corresponds to low X-ray beam intensity. Another portion of the audible range corresponds to high X-ray beam intensity. The transducer assembly may include an a photoresistor, a thin layer of X-ray fluorescent material, and a filter layer transparent to X-rays but opaque to visible light. X-rays from the beam undergoing alignment penetrate the filter layer and excite the layer of fluorescent material. The light emitted from the fluorescent material alters the resistance of the photoresistor which is in the electrical circuit including the audio pulse generator and a speaker. In employing the apparatus, the X-ray beam is aligned to a complete alignment by adjusting the X-ray beam to produce an audible sound of the maximum frequency.

Apparatus for monitoring X-ray beam alignment

DOEpatents

Steinmeyer, P.A.

1991-10-08

A self-contained, hand-held apparatus is provided for monitoring alignment of an X-ray beam in an instrument employing an X-ray source. The apparatus includes a transducer assembly containing a photoresistor for providing a range of electrical signals responsive to a range of X-ray beam intensities from the X-ray beam being aligned. A circuit, powered by a 7.5 VDC power supply and containing an audio frequency pulse generator whose frequency varies with the resistance of the photoresistor, is provided for generating a range of audible sounds. A portion of the audible range corresponds to low X-ray beam intensity. Another portion of the audible range corresponds to high X-ray beam intensity. The transducer assembly may include an a photoresistor, a thin layer of X-ray fluorescent material, and a filter layer transparent to X-rays but opaque to visible light. X-rays from the beam undergoing alignment penetrate the filter layer and excite the layer of fluorescent material. The light emitted from the fluorescent material alters the resistance of the photoresistor which is in the electrical circuit including the audio pulse generator and a speaker. In employing the apparatus, the X-ray beam is aligned to a complete alignment by adjusting the X-ray beam to produce an audible sound of the maximum frequency. 2 figures.

Measurement of Capillary Radius and Contact Angle within Porous Media.

PubMed

Ravi, Saitej; Dharmarajan, Ramanathan; Moghaddam, Saeed

2015-12-01

The pore radius (i.e., capillary radius) and contact angle determine the capillary pressure generated in a porous medium. The most common method to determine these two parameters is through measurement of the capillary pressure generated by a reference liquid (i.e., a liquid with near-zero contact angle) and a test liquid. The rate of rise technique, commonly used to determine the capillary pressure, results in significant uncertainties. In this study, we utilize a recently developed technique for independently measuring the capillary pressure and permeability to determine the equivalent minimum capillary radii and contact angle of water within micropillar wick structures. In this method, the experimentally measured dryout threshold of a wick structure at different wicking lengths is fit to Darcy's law to extract the maximum capillary pressure generated by the test liquid. The equivalent minimum capillary radii of different wick geometries are determined by measuring the maximum capillary pressures generated using n-hexane as the working fluid. It is found that the equivalent minimum capillary radius is dependent on the diameter of pillars and the spacing between pillars. The equivalent capillary radii of micropillar wicks determined using the new method are found to be up to 7 times greater than the current geometry-based first-order estimates. The contact angle subtended by water at the walls of the micropillars is determined by measuring the capillary pressure generated by water within the arrays and the measured capillary radii for the different geometries. This mean contact angle of water is determined to be 54.7°.

Modeling the directivity of parametric loudspeaker

NASA Astrophysics Data System (ADS)

Shi, Chuang; Gan, Woon-Seng

2012-09-01

The emerging applications of the parametric loudspeaker, such as 3D audio, demands accurate directivity control at the audible frequency (i.e. the difference frequency). Though the delay-and-sum beamforming has been proven adequate to adjust the steering angles of the parametric loudspeaker, accurate prediction of the mainlobe and sidelobes remains a challenging problem. It is mainly because of the approximations that are used to derive the directivity of the difference frequency from the directivity of the primary frequency, and the mismatches between the theoretical directivity and the measured directivity caused by system errors incurred at different stages of the implementation. In this paper, we propose a directivity model of the parametric loudspeaker. The directivity model consists of two tuning vectors corresponding to the spacing error and the weight error for the primary frequency. The directivity model adopts a modified form of the product directivity principle for the difference frequency to further improve the modeling accuracy.

Spatial hearing ability of the pigmented Guinea pig (Cavia porcellus): Minimum audible angle and spatial release from masking in azimuth.

PubMed

Greene, Nathaniel T; Anbuhl, Kelsey L; Ferber, Alexander T; DeGuzman, Marisa; Allen, Paul D; Tollin, Daniel J

2018-08-01

Despite the common use of guinea pigs in investigations of the neural mechanisms of binaural and spatial hearing, their behavioral capabilities in spatial hearing tasks have surprisingly not been thoroughly investigated. To begin to fill this void, we tested the spatial hearing of adult male guinea pigs in several experiments using a paradigm based on the prepulse inhibition (PPI) of the acoustic startle response. In the first experiment, we presented continuous broadband noise from one speaker location and switched to a second speaker location (the "prepulse") along the azimuth prior to presenting a brief, ∼110 dB SPL startle-eliciting stimulus. We found that the startle response amplitude was systematically reduced for larger changes in speaker swap angle (i.e., greater PPI), indicating that using the speaker "swap" paradigm is sufficient to assess stimulus detection of spatially separated sounds. In a second set of experiments, we swapped low- and high-pass noise across the midline to estimate their ability to utilize interaural time- and level-difference cues, respectively. The results reveal that guinea pigs can utilize both binaural cues to discriminate azimuthal sound sources. A third set of experiments examined spatial release from masking using a continuous broadband noise masker and a broadband chirp signal, both presented concurrently at various speaker locations. In general, animals displayed an increase in startle amplitude (i.e., lower PPI) when the masker was presented at speaker locations near that of the chirp signal, and reduced startle amplitudes (increased PPI) indicating lower detection thresholds when the noise was presented from more distant speaker locations. In summary, these results indicate that guinea pigs can: 1) discriminate changes in source location within a hemifield as well as across the midline, 2) discriminate sources of low- and high-pass sounds, demonstrating that they can effectively utilize both low-frequency interaural time and high-frequency level difference sound localization cues, and 3) utilize spatial release from masking to discriminate sound sources. This report confirms the guinea pig as a suitable spatial hearing model and reinforces prior estimates of guinea pig hearing ability from acoustical and physiological measurements. Copyright © 2018 Elsevier B.V. All rights reserved.

A general method for the derivation of the functional forms of the effective energy terms in coarse-grained energy functions of polymers. II. Backbone-local potentials of coarse-grained O 1 →4 -bonded polyglucose chains

NASA Astrophysics Data System (ADS)

Lubecka, Emilia A.; Liwo, Adam

2017-09-01

Based on the theory of the construction of coarse-grained force fields for polymer chains described in our recent work [A. K. Sieradzan et al., J. Chem. Phys. 146, 124106 (2017)], in this work effective coarse-grained potentials, to be used in the SUGRES-1P model of polysaccharides that is being developed in our laboratory, have been determined for the O ⋯O ⋯O virtual-bond angles (θ ) and for the dihedral angles for rotation about the O ⋯O virtual bonds (γ ) of 1 → 4 -linked glucosyl polysaccharides, for all possible combinations of [α ,β ]-[d,l]-glucose. The potentials of mean force corresponding to the virtual-bond angles and the virtual-bond dihedral angles were calculated from the free-energy surfaces of [α ,β ]-[d,l]-glucose pairs, determined by umbrella-sampling molecular-dynamics simulations with the AMBER12 force field, or combinations of the surfaces of two pairs sharing the overlapping residue, respectively, by integrating the respective Boltzmann factor over the dihedral angles λ for the rotation of the sugar units about the O ⋯O virtual bonds. Analytical expressions were subsequently fitted to the potentials of mean force. The virtual-bond-torsional potentials depend on both virtual-bond-dihedral angles and virtual-bond angles. The virtual-bond-angle potentials contain a single minimum at about θ =14 0° for all pairs except β -d-[α ,β ] -l-glucose, where the global minimum is shifted to θ =150° and a secondary minimum appears at θ =90°. The torsional potentials favor small negative γ angles for the α -d-glucose and extended negative angles γ for the β -d-glucose chains, as observed in the experimental structures of starch and cellulose, respectively. It was also demonstrated that the approximate expression derived based on Kubo's cluster-cumulant theory, whose coefficients depend on the identity of the disugar units comprising a trisugar unit that defines a torsional potential, fits simultaneously all torsional potentials very well, thus reducing the number of parameters significantly.

Anomalous contact angle hysteresis of a captive bubble: advancing contact line pinning.

PubMed

Hong, Siang-Jie; Chang, Feng-Ming; Chou, Tung-He; Chan, Seong Heng; Sheng, Yu-Jane; Tsao, Heng-Kwong

2011-06-07

Contact angle hysteresis of a sessile drop on a substrate consists of continuous invasion of liquid phase with the advancing angle (θ(a)) and contact line pinning of liquid phase retreat until the receding angle (θ(r)) is reached. Receding pinning is generally attributed to localized defects that are more wettable than the rest of the surface. However, the defect model cannot explain advancing pinning of liquid phase invasion driven by a deflating bubble and continuous retreat of liquid phase driven by the inflating bubble. A simple thermodynamic model based on adhesion hysteresis is proposed to explain anomalous contact angle hysteresis of a captive bubble quantitatively. The adhesion model involves two solid–liquid interfacial tensions (γ(sl) > γ(sl)′). Young’s equation with γ(sl) gives the advancing angle θ(a) while that with γ(sl)′ due to surface rearrangement yields the receding angle θ(r). Our analytical analysis indicates that contact line pinning represents frustration in surface free energy, and the equilibrium shape corresponds to a nondifferential minimum instead of a local minimum. On the basis of our thermodynamic model, Surface Evolver simulations are performed to reproduce both advancing and receding behavior associated with a captive bubble on the acrylic glass.

A Simple Accurate Alternative to the Minimum-Deviation Method for the Determination of the Refractive Index of a Prism.

ERIC Educational Resources Information Center

Waldenstrom, S.; Naqvi, K. Razi

1978-01-01

Proposes an alternative to the classical minimum-deviation method for determining the refractive index of a prism. This new "fixed angle of incidence method" may find applications in research. (Author/GA)

Effect of Impact Angle on the Erosion Rate of Coherent Granular Soil, with a Chernozemic Soil as an Example

NASA Astrophysics Data System (ADS)

Larionov, G. A.; Bushueva, O. G.; Gorobets, A. V.; Dobrovol'skaya, N. G.; Kiryukhina, Z. P.; Krasnov, S. F.; Kobylchenko Kuksina, L. V.; Litvin, L. F.; Sudnitsyn, I. I.

2018-02-01

It has been shown in experiments in a hydraulic flume with a knee-shaped bend that the rate of soil erosion more than doubles at the flow impact angles to the channel side from 0° to 50°. At higher channel bends, the experiment could not be performed because of backwater. Results of erosion by water stream approaching the sample surface at angles between 2° and 90° are reported. It has been found that the maximum erosion rate is observed at flow impact angles of about 45°, and the minimum rate at 90°. The minimum soil erosion rate is five times lower than the maximum erosion rate. This is due to the difference in the rate of free water penetration into the upper soil layer, and the impact of the hydrodynamic pressure, which is maximum at the impact angle of 90°. The penetration of water into the interaggregate space results in the breaking of bonds between aggregates, which is the main condition for the capture of particles by the flow.

Silent emergency alarm system for schools and the like

NASA Technical Reports Server (NTRS)

Read, W. S.; Roberts, V. W. (Inventor)

1973-01-01

An emergency alert system is described. In a school each classroom (or other area) is instrumented with a hidden microphone and receiver tuned to a non-audible frequency. The receivers' outputs are connected to a central display unit in the school's administrative office. Each instructor is provided with a small concealable transmitter which, when hand activated by the instructor upon the occurrance of any emergency, generates a non-audible signal at the receiver's tuned frequency.

The homogeneity of audibility and prosody of Zulu words for speech reception threshold (SRT) testing.

PubMed

Panday, Seema; Kathard, Harsha; Pillay, Mershen; Govender, Cyril

2009-01-01

The aim of this investigation was to determine which of 58 preselected Zulu words developed by Panday et al. (2007) could be used for Speech Reception Threshold (SRT) testing. To realize this aim the homogeneity of audibility of 58 bisyllabic Zulu low tone verbs was measured, followed by an analysis of the prosodic features of the selected words. The words were digitally recorded by a Zulu first language male speaker and presented at 6 intensity levels to 30 Zulu first language speakers (18-25 years, mean age of 21.5 years), whose hearing was normal. Homogeneity of audibility was determined by employing logistic regression analysis. Twenty eight words met the criterion of homogeneity of audibility. This was evidenced by a mean slope of 50% at 5.98%/dB. The prosodic features of the twenty eight words were further analyzed using a computerized speech laboratory system. The findings confirmed that the pitch contours of the words followed the prosodic pattern apparent within Zulu linguistic structure. Eighty nine percent of the Zulu verbs were found to have a difference in the pitch pattern between the two syllables i.e. the first syllable was low in pitch, while the second syllable was high in pitch. It emerged that the twenty eight words could be used for establishing SRT within a normal hearing Zulu speaking population. Further research within clinical populations is recommended.

Frequencies of inaudible high-frequency sounds differentially affect brain activity: positive and negative hypersonic effects.

PubMed

Fukushima, Ariko; Yagi, Reiko; Kawai, Norie; Honda, Manabu; Nishina, Emi; Oohashi, Tsutomu

2014-01-01

The hypersonic effect is a phenomenon in which sounds containing significant quantities of non-stationary high-frequency components (HFCs) above the human audible range (max. 20 kHz) activate the midbrain and diencephalon and evoke various physiological, psychological and behavioral responses. Yet important issues remain unverified, especially the relationship existing between the frequency of HFCs and the emergence of the hypersonic effect. In this study, to investigate the relationship between the hypersonic effect and HFC frequencies, we divided an HFC (above 16 kHz) of recorded gamelan music into 12 band components and applied them to subjects along with an audible component (below 16 kHz) to observe changes in the alpha2 frequency component (10-13 Hz) of spontaneous EEGs measured from centro-parieto-occipital regions (Alpha-2 EEG), which we previously reported as an index of the hypersonic effect. Our results showed reciprocal directional changes in Alpha-2 EEGs depending on the frequency of the HFCs presented with audible low-frequency component (LFC). When an HFC above approximately 32 kHz was applied, Alpha-2 EEG increased significantly compared to when only audible sound was applied (positive hypersonic effect), while, when an HFC below approximately 32 kHz was applied, the Alpha-2 EEG decreased (negative hypersonic effect). These findings suggest that the emergence of the hypersonic effect depends on the frequencies of inaudible HFC.

Characteristics of Pitch Angle Distributions of 100s Kev Electrons in the Slot Region and Inner Radiation Belt­­­­­­­­

NASA Astrophysics Data System (ADS)

Zhao, H.; Li, X.; Blake, J. B.; Fennell, J.; Claudepierre, S. G.; Baker, D. N.; Jaynes, A. N.; Malaspina, D.

2014-12-01

The pitch angle distribution (PAD) of energetic electrons in the slot region and inner radiation belt received little attention in the past decades due to the lack of quality measurements. Using the state-of-art pitch-angle-resolved data from the Magnetic Electron Ion Spectrometer (MagEIS) instrument onboard the Van Allen Probes, a detailed analysis of 100s keV electron PADs below L =4 is performed, in which the PADs is categorized into three types: normal (flux peaking at 90°), cap (exceedingly peaking narrowly around 90°) and 90°-minimum (lower flux at 90°) PADs. By examining the characteristics of the PADs of 460 keV electrons for over a year, we find that the 90°-minimum PADs are generally present in the inner belt (L<2), while normal PADs dominate at L~3.5-4. In the region between, 90°-minimum PADs dominate during injection times and normal PADs dominate during quiet times. Cap PADs appear mostly at the decay phase of storms in the slot region and are likely caused by the pitch angle scattering of hiss waves. Fitting the normal PADs into sinnα form, the parameter n is much higher below L=3 than that in the outer belt and relatively constant in the inner belt but changes significantly in the slot region (2

Psychoacoustic Analysis of Synthesized Jet Noise

NASA Technical Reports Server (NTRS)

Okcu, Selen; Rathsam, Jonathan; Rizzi, Stephen A.

2013-01-01

An aircraft noise synthesis capability is being developed so the annoyance caused by proposed aircraft can be assessed during the design stage. To make synthesized signals as realistic as possible, high fidelity simulation is required for source (e.g., engine noise, airframe noise), propagation and receiver effects. This psychoacoustic study tests whether the jet noise component of synthesized aircraft engine noise can be made more realistic using a low frequency oscillator (LFO) technique to simulate fluctuations in level observed in recordings. Jet noise predictions are commonly made in the frequency domain based on models of time-averaged empirical data. The synthesis process involves conversion of the frequency domain prediction into an audible pressure time history. However, because the predictions are time-invariant, the synthesized sound lacks fluctuations observed in recordings. Such fluctuations are hypothesized to be perceptually important. To introduce time-varying characteristics into jet noise synthesis, a method has been developed that modulates measured or predicted 1/3-octave band levels with a (<20Hz) LFO. The LFO characteristics are determined through analysis of laboratory jet noise recordings. For the aft emission angle, results indicate that signals synthesized using a generic LFO are perceived as more similar to recordings than those using no LFO, and signals synthesized with an angle-specific LFO are more similar to recordings than those synthesized with a generic LFO.

Far Forward Life Support System (FFLSS) Phase II

DTIC Science & Technology

2001-05-01

button will clear audible, flashing , or constant red alarms. Pushing the Config button drops down to the Level 2 menu (bottom line of Figure 8). In...disabled. Again, with testing this audible noise can be disabled. The visual flashing or constant red cannot be disabled. Pushing Return goes back to Level...Calling PLOTPIXEL( x ,y) and PLOTLINE(xl,x2,yl,y2) is as simple as pushing the appropriate bytes (unsigned integers) onto the stack and jumping to the

Effects of consumption-oriented versus trophy-oriented fisheries on Muskellunge population size structure in northern Wisconsin

USGS Publications Warehouse

Faust, Matthew D.; Hansen, Michael J.

2016-01-01

To determine whether a consumption-oriented fishery was compatible with a trophy-oriented fishery for Muskellunge Esox masquinongy, we modeled effects of a spearing fishery and recreational angling fishery on population size structure (i.e., numbers of fish ≥ 102, 114, and 127 cm) in northern Wisconsin. An individual-based simulation model was used to quantify the effect of harvest mortality at currently observed levels of recreational angling and tribal spearing fishery exploitation, along with simulated increases in exploitation, for three typical growth potentials (i.e., low, moderate, and high) of Muskellunge in northern Wisconsin across a variety of minimum length limits (i.e., 71, 102, 114, and 127 cm). Populations with moderate to high growth potential and minimum length limits ≥ 114 cm were predicted to have lower declines in numbers of trophy Muskellunge when subjected to angling-only and mixed fisheries at observed and increased levels of exploitation, which suggested that fisheries with disparate motivations may be able to coexist under certain conditions such as restrictive length limits and low levels of exploitation. However, for most Muskellunge populations in northern Wisconsin regulated by a 102-cm minimum length limit, both angling and spearing fisheries may reduce numbers of trophy Muskellunge as larger declines were predicted across all growth potentials. Our results may be useful if Muskellunge management options in northern Wisconsin are re-examined in the future.

A Patient-Centered, Provider-Facilitated Approach to the Refinement of Nonlinear Frequency Compression Parameters Based on Subjective Preference Ratings of Amplified Sound Quality.

PubMed

Johnson, Earl E; Light, Keri C

2015-09-01

To evaluate sound quality preferences of participants wearing hearing aids with different strengths of nonlinear frequency compression (NFC) processing versus no NFC processing. Two analysis methods, one without and one with a qualifier as to the magnitude of preferences, were compared for their percent agreement to differentiate a small difference in perceived sound quality as a result of applied NFC processing. A single-blind design was used with participants unaware of the presence or strength of NFC processing (independent variable). The National Acoustic Laboratories-Nonlinear 2 (NAL-NL2) prescription of amplification was chosen because audibility is intentionally not prescribed in the presence of larger sensorineural hearing loss thresholds. A lack of prescribed audibility, when present, was deemed an objective qualifier for NFC. NFC is known to improve the input bandwidth available to listeners when high-frequency audibility is not otherwise available and increasing strengths of NFC were examined. Experimental condition 3 (EC3) was stronger than the manufacturer default (EC2). More aggressive strengths (e.g., EC4 and EC5), however, were expected to include excessive distortion and even reduce the output bandwidth that had been prescribed as audible by NAL-NL2 (EC1). A total of 14 male Veterans with severe high-frequency sensorineural hearing loss. Participant sound quality preference ratings (dependent variable) without a qualifier as to the magnitude of preference were analyzed based on binomial probability theory, as is traditional with paired comparison data. The ratings with a qualifier as to the magnitude of preference were analyzed based on the nonparametric statistic of the Wilcoxon signed rank test. The binomial probability analysis method identified a sound quality preference as well as the nonparametric probability test method. As the strength of NFC increased, more participants preferred the EC with less NFC. Fourteen of 14 participants showed equal preference between EC1 and EC2 perhaps, in part, because EC2 showed no objective improvement in audibility for six of the 14 participants (42%). Thirteen of the 14 participants showed no preference between NAL-NL2 and EC3, but all participants had an objective improvement in audibility. With more NFC than EC3, more and more participants preferred the other EC with less NFC in the paired comparison. By referencing the recommended sensation levels of amplitude compression (e.g., NAL-NL2) in the ear canal of hearing aid wearers, the targeting of NFC parameters can likely be optimized with respect to improvements in effective audibility that may contribute to speech recognition without adversely impacting sound quality. After targeting of NFC parameters, providers can facilitate decisions about the use of NFC parameters (strengths of processing) via sound quality preference judgments using paired comparisons. American Academy of Audiology.

Wideband acoustic records of explosive volcanic eruptions at Stromboli: New insights on the explosive process and the acoustic source

NASA Astrophysics Data System (ADS)

Goto, A.; Ripepe, M.; Lacanna, G.

2014-06-01

Wideband acoustic waves, both inaudible infrasound (<20 Hz) and audible component (>20 Hz), generated by strombolian eruptions were recorded at 5 kHz and correlated with video images. The high sample rate revealed that in addition to the known initial infrasound, the acoustic signal includes an energetic high-frequency (typically >100 Hz) coda. This audible signal starts before the positive infrasound onset goes negative. We suggest that the infrasonic onset is due to magma doming at the free surface, whereas the immediate high-frequency signal reflects the following explosive discharge flow. During strong gas-rich eruptions, positively skewed shockwave-like components with sharp compression and gradual depression appeared. We suggest that successive bursting of overpressurized small bubbles and the resultant volcanic jets sustain the highly gas-rich explosions and emit the audible sound. When the jet is supersonic, microexplosions of ambient air entrained in the hot jet emit the skewed waveforms.

Beaconing Signalization Substantially Reduces Blind Pedestrians’ Veer on Snow-Covered Pavement

PubMed Central

Guth, David A.; Long, Richard G.; Kim, Dae Shik; Robertson, Elizabeth A.; Reesor, Abbie L.; Bacik, Catherine J.; Eckert, Jaclyn M.

2017-01-01

Veering outside of crosswalks is a common problem experienced by individuals who are blind. One technology found to be effective for reducing this veer when other guidance cues are absent is audible beaconing. However, veering in general and veering from crosswalks in particular have been studied primarily on smooth, flat walking surfaces such as clear pavement. This experiment compared veering on clear pavement with veering on snow-covered pavement, with and without audible beaconing. Eleven blind participants traveling with long canes attempted to walk a straight path for 72 ft (21.9 m), a typical length of a six-lane crosswalk. Beaconing substantially reduced veering at 36 ft (11.0 m) and 72 ft from the starting point and enabled participants to remain within a simulated crosswalk. Walking on snow was not found to affect veering but did increase the number of steps taken. The findings suggest that in snowy and clear conditions alike, audible beaconing is an effective wayfinding tool for intersections equipped with accessible pedestrian signals. PMID:29307955

Short-Term and Working Memory Impairments in Early-Implanted, Long-Term Cochlear Implant Users Are Independent of Audibility and Speech Production

PubMed Central

AuBuchon, Angela M.; Pisoni, David B.; Kronenberger, William G.

2015-01-01

OBJECTIVES Determine if early-implanted, long-term cochlear implant (CI) users display delays in verbal short-term and working memory capacity when processes related to audibility and speech production are eliminated. DESIGN Twenty-three long-term CI users and 23 normal-hearing controls each completed forward and backward digit span tasks under testing conditions which differed in presentation modality (auditory or visual) and response output (spoken recall or manual pointing). RESULTS Normal-hearing controls reproduced more lists of digits than the CI users, even when the test items were presented visually and the responses were made manually via touchscreen response. CONCLUSIONS Short-term and working memory delays observed in CI users are not due to greater demands from peripheral sensory processes such as audibility or from overt speech-motor planning and response output organization. Instead, CI users are less efficient at encoding and maintaining phonological representations in verbal short-term memory utilizing phonological and linguistic strategies during memory tasks. PMID:26496666

Short-Term and Working Memory Impairments in Early-Implanted, Long-Term Cochlear Implant Users Are Independent of Audibility and Speech Production.

PubMed

AuBuchon, Angela M; Pisoni, David B; Kronenberger, William G

2015-01-01

To determine whether early-implanted, long-term cochlear implant (CI) users display delays in verbal short-term and working memory capacity when processes related to audibility and speech production are eliminated. Twenty-three long-term CI users and 23 normal-hearing controls each completed forward and backward digit span tasks under testing conditions that differed in presentation modality (auditory or visual) and response output (spoken recall or manual pointing). Normal-hearing controls reproduced more lists of digits than the CI users, even when the test items were presented visually and the responses were made manually via touchscreen response. Short-term and working memory delays observed in CI users are not due to greater demands from peripheral sensory processes such as audibility or from overt speech-motor planning and response output organization. Instead, CI users are less efficient at encoding and maintaining phonological representations in verbal short-term memory using phonological and linguistic strategies during memory tasks.

Beaconing Signalization Substantially Reduces Blind Pedestrians' Veer on Snow-Covered Pavement.

PubMed

Guth, David A; Long, Richard G; Kim, Dae Shik; Robertson, Elizabeth A; Reesor, Abbie L; Bacik, Catherine J; Eckert, Jaclyn M

2017-01-01

Veering outside of crosswalks is a common problem experienced by individuals who are blind. One technology found to be effective for reducing this veer when other guidance cues are absent is audible beaconing. However, veering in general and veering from crosswalks in particular have been studied primarily on smooth, flat walking surfaces such as clear pavement. This experiment compared veering on clear pavement with veering on snow-covered pavement, with and without audible beaconing. Eleven blind participants traveling with long canes attempted to walk a straight path for 72 ft (21.9 m), a typical length of a six-lane crosswalk. Beaconing substantially reduced veering at 36 ft (11.0 m) and 72 ft from the starting point and enabled participants to remain within a simulated crosswalk. Walking on snow was not found to affect veering but did increase the number of steps taken. The findings suggest that in snowy and clear conditions alike, audible beaconing is an effective wayfinding tool for intersections equipped with accessible pedestrian signals.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo Baonian; Gossmann, Hans-Joachim; Toh, Terry

Angle control has been widely accepted as the key requirement for ion implantation in semiconductor device processing. From an ion implanter point of view, the incident ion direction should be measured and corrected by suitable techniques, such as XP-VPS for the VIISta implanter platform, to ensure precision ion placement in device structures. So called V-curves have been adopted to generate the wafer-based calibration using channeling effects as the Si lattice steer ions into a channeling direction. Thermal Wave (TW) or sheet resistance (Rs) can be used to determine the minimum of the angle response curve. Normally it is expected thatmore » the TW and Rs have their respective minima at identical angles. However, the TW and Rs response to the angle variations does depend on factors such as implant species, dose, and wafer temperature. Implant damage accumulation effects have to be considered for data interpretation especially for some 'abnormal' V-curve data. In this paper we will discuss some observed 'abnormal' angle responses, such as a) TW/Rs reverse trend for Arsenic beam, 2) 'W' shape of Rs Boron, and 3) apparent TW/Rs minimum difference for high tilt characterization, along with experimental data and TCAD simulations.« less

Minimum emittance in TBA and MBA lattices

NASA Astrophysics Data System (ADS)

Xu, Gang; Peng, Yue-Mei

2015-03-01

For reaching a small emittance in a modern light source, triple bend achromats (TBA), theoretical minimum emittance (TME) and even multiple bend achromats (MBA) have been considered. This paper derived the necessary condition for achieving minimum emittance in TBA and MBA theoretically, where the bending angle of inner dipoles has a factor of 31/3 bigger than that of the outer dipoles. Here, we also calculated the conditions attaining the minimum emittance of TBA related to phase advance in some special cases with a pure mathematics method. These results may give some directions on lattice design.

Electrocardiogram provides a continuous heart rate faster than oximetry during neonatal resuscitation.

PubMed

Katheria, Anup; Rich, Wade; Finer, Neil

2012-11-01

To compare the time required to obtain a continuous audible heart rate signal from an electrocardiogram (ECG) monitor and pulse oximeter (PO) in infants requiring resuscitation. Infants who had both ECG and PO placed during resuscitation were analyzed using video and analog recordings. The median times from arrival until the ECG electrodes and PO sensor were placed, and the time to achieve audible tones from the devices, were compared. Forty-six infants had ECG and PO data. Thirty infants were very low birth weight (23-30 weeks). There was a difference in the median total time to place either device (26 vs 38 seconds; P = .04), and a difference (P < .001) in the time to achieve an audible heart rate signal after ECG lead (2 seconds) versus PO probe (24 seconds) placement. In infants weighing >1500 g (n = 16), the median time (interquartile range) to place the ECG was 20 seconds (14-43) whereas the time to place the PO was 36 seconds (28-56) (P = .74). The median times (interquartile range) to acquire a signal from the ECG and PO were 4 seconds (1-6) and 32 seconds (15-40, P = .001), respectively. During the first minutes of resuscitation, 93% of infants had an ECG heart rate compared with only 56% for PO. Early application of ECG electrodes during infant resuscitation can provide the resuscitation team with a continuous audible heart rate, and its use may improve the timeliness of appropriate critical interventions.

The effects of audibility and novel word learning ability on vocabulary level in children with cochlear implants.

PubMed

Davidson, Lisa S; Geers, Ann E; Nicholas, Johanna G

2014-07-01

A novel word learning (NWL) paradigm was used to explore underlying phonological and cognitive mechanisms responsible for delayed vocabulary level in children with cochlear implants (CIs). One hundred and one children using CIs, 6-12 years old, were tested along with 47 children with normal hearing (NH). Tests of NWL, receptive vocabulary, and speech perception at 2 loudness levels were administered to children with CIs. Those with NH completed the NWL task and a receptive vocabulary test. CI participants with good audibility (GA) versus poor audibility (PA) were compared on all measures. Analysis of variance was used to compare performance across the children with NH and the two groups of children with CIs. Multiple regression analysis was employed to identify independent predictors of vocabulary outcomes. Children with CIs in the GA group scored higher in receptive vocabulary and NWL than children in the PA group, although they did not reach NH levels. CI-aided pure tone threshold and performance on the NWL task predicted independent variance in vocabulary after accounting for other known predictors. Acquiring spoken vocabulary is facilitated by GA with a CI and phonological learning and memory skills. Children with CIs did not learn novel words at the same rate or achieve the same receptive vocabulary levels as their NH peers. Maximizing audibility for the perception of speech and direct instruction of new vocabulary may be necessary for children with CIs to reach levels seen in peers with NH.

Projectile motion in real-life situation: Kinematics of basketball shooting

NASA Astrophysics Data System (ADS)

Changjan, A.; Mueanploy, W.

2015-06-01

Basketball shooting is a basic practice for players. The path of the ball from the players to the hoop is projectile motion. For undergraduate introductory physics courses student must be taught about projectile motion. Basketball shooting can be used as a case study for learning projectile motion from real-life situation. In this research, we discuss the relationship between optimal angle, minimum initial velocity and the height of the ball before the player shoots the ball for basketball shooting problem analytically. We found that the value of optimal angle and minimum initial velocity decreases with increasing the height of the ball before the player shoots the ball.

Position Between Trunk and Pelvis During Gait Depending on the Gross Motor Function Classification System.

PubMed

Sanz-Mengibar, Jose Manuel; Altschuck, Natalie; Sanchez-de-Muniain, Paloma; Bauer, Christian; Santonja-Medina, Fernando

2017-04-01

To understand whether there is a trunk postural control threshold in the sagittal plane for the transition between the Gross Motor Function Classification System (GMFCS) levels measured with 3-dimensional gait analysis. Kinematics from 97 children with spastic bilateral cerebral palsy from spine angles according to Plug-In Gait model (Vicon) were plotted relative to their GMFCS level. Only average and minimum values of the lumbar spine segment correlated with GMFCS levels. Maximal values at loading response correlated independently with age at all functional levels. Average and minimum values were significant when analyzing age in combination with GMFCS level. There are specific postural control patterns in the average and minimum values for the position between trunk and pelvis in the sagittal plane during gait, for the transition among GMFCS I-III levels. Higher classifications of gross motor skills correlate with more extended spine angles.

Long-Wave Infrared Semiconductor Negative Refraction Metamaterials for High-Resolution Imaging

DTIC Science & Technology

2011-02-14

corresponding to the minimum in TM-polarized reflection. Negative refraction region starts from discontinuity of the Brewster angle (~8) and ends when... Brewster angle disappears (~11 ). Page | 5 Goal 2: loss reduction by incorporating the material gain As mentioned above, the design of...Tuning the focus of a plasmonic lens by the incident angle ,” Appl. Phys. Lett. 88, 171108 (2006). 11. I. I. Smolyaninov, D. L. Mazzoni, J. Mait, and C

14 CFR 29.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2011 CFR

2011-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 23.1391 - Minimum intensities in the horizontal plane of position lights.

Code of Federal Regulations, 2012 CFR

2012-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white) 110° to...

14 CFR 29.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2013 CFR

2013-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 27.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2013 CFR

2013-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 10° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 25.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 23.1391 - Minimum intensities in the horizontal plane of position lights.

Code of Federal Regulations, 2013 CFR

2013-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white) 110° to...

14 CFR 25.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2011 CFR

2011-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10° 10° to 20° 20° to 110° 40 30 5 A (rear white...

14 CFR 29.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 27.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2011 CFR

2011-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 10° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 25.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2013 CFR

2013-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 27.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 10° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 23.1391 - Minimum intensities in the horizontal plane of position lights.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white) 110° to...

14 CFR 27.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2012 CFR

2012-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 10° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 25.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2012 CFR

2012-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10° 10° to 20° 20° to 110° 40 30 5 A (rear white...

14 CFR 29.1391 - Minimum intensities in the horizontal plane of forward and rear position lights.

Code of Federal Regulations, 2012 CFR

2012-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (forward red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white...

14 CFR 23.1391 - Minimum intensities in the horizontal plane of position lights.

Code of Federal Regulations, 2011 CFR

2011-01-01

...: Dihedral angle (light included) Angle from right or left of longitudinal axis, measured from dead ahead Intensity (candles) L and R (red and green) 0° to 10°10° to 20° 20° to 110° 4030 5 A (rear white) 110° to...

Nonlinear Control Theory for Missile Autopilot Design.

DTIC Science & Technology

1987-04-24

minimum-time controller which includes constraints on both controls and angle-of-attack is developed and an example is given. -12- - - -~ *% PO PmCF E- A...constructed. In this case, some ideas from robotics on minimum-time trajectory planning under path constraints (see, e.g., Rajan (1985), Sahar and...Auto Cont., Vol. AC-29, No. 4, p. 361. Rajan, V.T. (1985), "Minimum-Time Trajectory Planning ", Proc IEEE Kobotics and Automation Conf., St. Louis. Reed

Development of a Novel Bone Conduction Verification Tool Using a Surface Microphone: Validation With Percutaneous Bone Conduction Users.

PubMed

Hodgetts, William; Scott, Dylan; Maas, Patrick; Westover, Lindsey

2018-03-23

To determine if a newly-designed, forehead-mounted surface microphone would yield equivalent estimates of audibility when compared to audibility measured with a skull simulator for adult bone conduction users. Data was analyzed using a within subjects, repeated measures design. There were two different sensors (skull simulator and surface microphone) measuring the same hearing aid programmed to the same settings for all subjects. We were looking for equivalent results. Twenty-one adult percutaneous bone conduction users (12 females and 9 males) were recruited for this study. Mean age was 54.32 years with a standard deviation of 14.51 years. Nineteen of the subjects had conductive/mixed hearing loss and two had single-sided deafness. To define audibility, we needed to establish two things: (1) in situ-level thresholds at each audiometric frequency in force (skull simulator) and in sound pressure level (SPL; surface microphone). Next, we measured the responses of the preprogrammed test device in force on the skull simulator and in SPL on the surface mic in response to pink noise at three input levels: 55, 65, and 75 dB SPL. The skull simulator responses were converted to real head force responses by means of an individual real head to coupler difference transform. Subtracting the real head force level thresholds from the real head force output of the test aid yielded the audibility for each audiometric frequency for the skull simulator. Subtracting the SPL thresholds from the surface microphone from the SPL output of the test aid yielded the audibility for each audiometric frequency for the surface microphone. The surface microphone was removed and retested to establish the test-retest reliability of the tool. We ran a 2 (sensor) × 3 (input level) × 10 (frequency) mixed analysis of variance to determine if there were any significant main effects and interactions. There was a significant three-way interaction, so we proceeded to explore our planned comparisons. There were 90 planned comparisons of interest, three at each frequency (3 × 10) for the three input levels (30 × 3). Therefore, to minimize a type 1 error associated with multiple comparisons, we adjusted alpha using the Holm-Bonferroni method. There were five comparisons that yielded significant differences between the skull simulator and surface microphone (test and retest) in the estimation of audibility. However, the mean difference in these effects was small at 3.3 dB. Both sensors yielded equivalent results for the majority of comparisons. Models of bone conduction devices that have intact skin cannot be measured with the skull simulator. This study is the first to present and evaluate a new tool for bone conduction verification. The surface microphone is capable of yielding equivalent audibility measurements as the skull simulator for percutaneous bone conduction users at multiple input levels. This device holds potential for measuring other bone conduction devices (Sentio, BoneBridge, Attract, Soft headband devices) that do not have a percutaneous implant.

Design Enhancements of the Two-Dimensional, Dual Throat Fluidic Thrust Vectoring Nozzle Concept

NASA Technical Reports Server (NTRS)

Flamm, Jeffrey D.; Deere, Karen A.; Mason, Mary L.; Berrier, Bobby L.; Johnson, Stuart K.

2006-01-01

A Dual Throat Nozzle fluidic thrust vectoring technique that achieves higher thrust-vectoring efficiencies than other fluidic techniques, without sacrificing thrust efficiency has been developed at NASA Langley Research Center. The nozzle concept was designed with the aid of the structured-grid, Reynolds-averaged Navier-Stokes computational fluidic dynamics code PAB3D. This new concept combines the thrust efficiency of sonic-plane skewing with increased thrust-vectoring efficiencies obtained by maximizing pressure differentials in a separated cavity located downstream of the nozzle throat. By injecting secondary flow asymmetrically at the upstream minimum area, a new aerodynamic minimum area is formed downstream of the geometric minimum and the sonic line is skewed, thus vectoring the exhaust flow. The nozzle was tested in the NASA Langley Research Center Jet Exit Test Facility. Internal nozzle performance characteristics were defined for nozzle pressure ratios up to 10, with a range of secondary injection flow rates up to 10 percent of the primary flow rate. Most of the data included in this paper shows the effect of secondary injection rate at a nozzle pressure ratio of 4. The effects of modifying cavity divergence angle, convergence angle and cavity shape on internal nozzle performance were investigated, as were effects of injection geometry, hole or slot. In agreement with computationally predicted data, experimental data verified that decreasing cavity divergence angle had a negative impact and increasing cavity convergence angle had a positive impact on thrust vector angle and thrust efficiency. A curved cavity apex provided improved thrust ratios at some injection rates. However, overall nozzle performance suffered with no secondary injection. Injection holes were more efficient than the injection slot over the range of injection rates, but the slot generated larger thrust vector angles for injection rates less than 4 percent of the primary flow rate.

Optimal Space Station solar array gimbal angle determination via radial basis function neural networks

NASA Technical Reports Server (NTRS)

Clancy, Daniel J.; Oezguener, Uemit; Graham, Ronald E.

1994-01-01

The potential for excessive plume impingement loads on Space Station Freedom solar arrays, caused by jet firings from an approaching Space Shuttle, is addressed. An artificial neural network is designed to determine commanded solar array beta gimbal angle for minimum plume loads. The commanded angle would be determined dynamically. The network design proposed involves radial basis functions as activation functions. Design, development, and simulation of this network design are discussed.

Objective lens simultaneously optimized for pupil ghosting, wavefront delivery and pupil imaging

NASA Technical Reports Server (NTRS)

Olczak, Eugene G (Inventor)

2011-01-01

An objective lens includes multiple optical elements disposed between a first end and a second end, each optical element oriented along an optical axis. Each optical surface of the multiple optical elements provides an angle of incidence to a marginal ray that is above a minimum threshold angle. This threshold angle minimizes pupil ghosts that may enter an interferometer. The objective lens also optimizes wavefront delivery and pupil imaging onto an optical surface under test.

New vibro-acoustic paradigms in biological tissues with application to diagnosis of pulmonary disorders

NASA Astrophysics Data System (ADS)

Zhang, Xiangling

The fundamental objective of the present study is to improve our understanding of audible sound propagation in the pulmonary system and torso. A related applied objective is to assess the feasibility of using audible acoustics for diagnosis of specific pulmonary conditions, such as pneumothorax (PTX). To accomplish these objectives, this study includes theoretical, computational and experimental developments aimed at: (1) better identifying the mechanical dynamic properties of soft biological tissues found in the torso region, (2) investigating the mechanisms of sound attenuation that occur when a PTX is present using greatly simplified theoretical and computational models, and (3) exploring the feasibility and utility of more comprehensive and precise computational finite element models of audible sound propagation in the pulmonary system and torso that would aid in related diagnostic developments. Mechanical material properties of soft biological tissue are studied for the low audible frequency range. The sensitivity to shear viscoelastic material constants of theoretical solutions for radiation impedance and surface wave motion are compared. Theoretical solutions are also compared to experimental measurements and numerical results from finite element analysis. It is found that, while prior theoretical solutions for radiation impedance are accurate, use of such measurements to estimate shear viscoelastic constants is not as precise as the use of surface wave measurements. The feasibility of using audible sound for diagnosis of pneumothorax is studied. Simplified one- and two-dimensional theoretical and numerical models of sound transmission through the pulmonary system and chest region to the chest wall surface are developed to more clearly understand the mechanism of energy loss when a pneumothorax is present, relative to a baseline case. A canine study on which these models are based predicts significant decreases in acoustic transmission strength when a pneumothorax is presented, in qualitative agreement with experimental measurements in dogs. Finally, the feasibility of building three-dimensional computational models is studied based on CT images of human subject or combination of the Horsfield airway model with geometry of other parts approximate from medical illustration. Preliminary results from these models show the same trend of acoustic energy loss when a PTX is present.

Territorial black-capped chickadee males respond faster to high- than to low-frequency songs in experimentally elevated noise conditions

PubMed Central

Slabbekoorn, Hans; Otter, Ken A.

2017-01-01

Low-frequency urban noise can interfere with avian communication through masking. Some species are able to shift the frequency of their vocalizations upwards in noisy conditions, which may reduce the effects of masking. However, results from playback studies investigating whether or not such vocal changes improve audibility in noisy conditions are not clear; the responses of free-ranging individuals to shifted signals are potentially confounded by functional trade-offs between masking-related audibility and frequency-dependent signal quality. Black-capped chickadees (Poecile atricapillus) naturally sing their songs at several different frequencies as they pitch-shift to match conspecifics during song-matching contests. They are also known to switch to higher song frequencies in response to experimental noise exposure. Each male produces both high- and low-frequency songs and absolute frequency is not a signal of aggression or dominance, making this an interesting species in which to test whether higher-frequency songs are more audible than lower-frequency songs in noisy conditions. We conducted playback studies across southern and central British Columbia, Canada, using paired song stimuli (high- vs low-frequency songs, n = 24 pairs) embedded in synthetic background noise created to match typical urban sound profiles. Over the course of each playback, the signal-to-noise ratio of the song stimuli was gradually increased by raising the amplitude of the song stimuli while maintaining background noise at a constant amplitude. We evaluated variation in how quickly and aggressively territorial males reacted to each of the paired stimuli. We found that males responded more quickly to playbacks of high- than low-frequency songs when high-frequency songs were presented first, but not when low-frequency songs were first. This difference may be explained by high-frequency songs being more audible combined with a carry-over effect resulting in slower responses to the second stimulus due to habituation. We observed no difference in overall aggression between stimuli. These results suggest that high-frequency songs may be more audible under noisy conditions. PMID:28462051

Estimation of additive forces and moments for supersonic inlets

NASA Technical Reports Server (NTRS)

Perkins, Stanley C., Jr.; Dillenius, Marnix F. E.

1991-01-01

A technique for estimating the additive forces and moments associated with supersonic, external compression inlets as a function of mass flow ratio has been developed. The technique makes use of a low order supersonic paneling method for calculating minimum additive forces at maximum mass flow conditions. A linear relationship between the minimum additive forces and the maximum values for fully blocked flow is employed to obtain the additive forces at a specified mass flow ratio. The method is applicable to two-dimensional inlets at zero or nonzero angle of attack, and to axisymmetric inlets at zero angle of attack. Comparisons with limited available additive drag data indicate fair to good agreement.

Audible acoustics in high-shear wet granulation: application of frequency filtering.

PubMed

Hansuld, Erin M; Briens, Lauren; McCann, Joe A B; Sayani, Amyn

2009-08-13

Previous work has shown analysis of audible acoustic emissions from high-shear wet granulation has potential as a technique for end-point detection. In this research, audible acoustic emissions (AEs) from three different formulations were studied to further develop this technique as a process analytical technology. Condenser microphones were attached to three different locations on a PMA-10 high-shear granulator (air exhaust, bowl and motor) to target different sound sources. Size, flowability and tablet break load data was collected to support formulator end-point ranges and interpretation of AE analysis. Each formulation had a unique total power spectral density (PSD) profile that was sensitive to granule formation and end-point. Analyzing total PSD in 10 Hz segments identified profiles with reduced run variability and distinct maxima and minima suitable for routine granulation monitoring and end-point control. A partial least squares discriminant analysis method was developed to automate selection of key 10 Hz frequency groups using variable importance to projection. The results support use of frequency refinement as a way forward in the development of acoustic emission analysis for granulation monitoring and end-point control.

Directional guidance from audible pedestrian signals for street crossing.

PubMed

Wall, Robert S; Ashmead, Daniel H; Bentzen, Billie Louise; Barlow, Janet

2004-10-10

Typical audible pedestrian signals indicate when the pedestrian walk interval is in effect but provide little, or even misleading information for directional alignment. In three experiments, blind and blindfolded sighted adults crossed a simulated crossing with recorded traffic noise to approximate street sounds. This was done to investigate how characteristics of signal presentation affected usefulness of the auditory signal for guiding crossing behaviour. Crossing was more accurate when signals came only from the far end of the crossing rather than the typical practice of presenting signals simultaneously from both ends. Alternating the signal between ends of the crossing was not helpful. Also, the customary practice of signalling two parallel crossings at the same time drew participants somewhat toward the opposite crossing. Providing a locator tone at the end of the crossing during the pedestrian clearance interval improved crossing accuracy. These findings provide a basis for designing audible pedestrian signals to enhance directional guidance. The principal findings were the same for blind and sighted participants and applied across a range of specific signals (e.g. chirps, clicks, voices).

Audible Beaconing with Accessible Pedestrian Signals

PubMed Central

Barlow, Janet M.; Scott, Alan C.; Bentzen, Billie Louise

2010-01-01

Purpose Although Accessible Pedestrian Signals (APS) are often assumed to provide wayfinding information, the type of APS that has been typically installed in the U.S has not had positive effects on finding crosswalks, locating pushbuttons, or providing directional guidance. This paper reports the results of research on crossings by blind pedestrians at complex signalized intersections, before and after the installation of APS with innovative audible beaconing features, designed to improve wayfinding. Methods Objective data on measures of street crossing performance by 56 participants was obtained at four intersections, two each in Charlotte, NC, and Portland, OR. Results In the first round of testing, APS with beaconing features resulted in only slightly improved wayfinding. Revisions to the audible beaconing features resulted in improved performance on four measures of wayfinding as compared to the pre-installation condition: beginning crossings within the crosswalk, ending crossings within the crosswalk, independence in finding the starting location, and independence in aligning to cross. Implications for Practice Use of APS that provide beaconing from the far-end of the crosswalk show promise of improving wayfinding at street crossings. PMID:20622978

Possibility of Atherosclerosis in an Arterial Bifurcation Model

PubMed Central

Arjmandi-Tash, Omid; Razavi, Seyed Esmail; Zanbouri, Ramin

2011-01-01

Introduction Arterial bifurcations are susceptible locations for formation of atherosclerotic plaques. In the present study, steady blood flow is investigated in a bifurcation model with a non-planar branch. Methods The influence of different bifurcation angles and non-planar branch is demonstrated on wall shear stress (WSS) distribution using three-dimensional Navier–Stokes equations. Results The WSS values are low in two locations at the top and bottom walls of the mother vessels just before the bifurcation, especially for higher bifurcation angles. These regions approach the apex of bifurcation with decreasing the bifurcation angle. The WSS magnitudes approach near to zero at the outer side of bifurcation plane and these locations are separation-prone. By increasing the bifurcation angle, the minimum WSS decreases at the outer side of bifurcation plane but low WSS region squeezes. WSS peaks exist on the inner side of bifurcation plane near the entry section of daughter vessels and these initial peaks drop as bifurcation angle is increased. Conclusion It is concluded that the non-planarity of the daughter vessel lowers the minimum WSS at the outer side of bifurcation and increases the maximum WSS at the inner side. So it seems that the formation of atherosclerotic plaques at bifurcation region in direction of non-planar daughter vessel is more risky. PMID:23678432

Research of working pulsation in closed angle based on rotating-sleeve distributing-flow system

NASA Astrophysics Data System (ADS)

Zhang, Yanjun; Zhang, Hongxin; Zhao, Qinghai; Jiang, Xiaotian; Cheng, Qianchang

2017-08-01

In order to reduce negative effects including hydraulic impact, noise and mechanical vibration, compression and expansion of piston pump in closed volume are used to optimize the angle between valve port and chamber. In addition, the mathematical model about pressurization and depressurization in pump chamber are analyzed based on distributing-flow characteristic, and it is necessary to use simulation software Fluent to simulate the distributing-flow fluid model so as to select the most suitable closed angle. As a result, when compression angle is 3°, the angle is closest to theoretical analysis and has the minimum influence on flow and pump pressure characteristic. Meanwhile, cavitation phenomenon appears in pump chamber in different closed angle on different degrees. Besides the flow pulsation is increasingly smaller with increasing expansion angle. Thus when expansion angle is 2°, the angle is more suitable for distributing-flow system.

Study on Operation Optimization of Pumping Station's 24 Hours Operation under Influences of Tides and Peak-Valley Electricity Prices

NASA Astrophysics Data System (ADS)

Yi, Gong; Jilin, Cheng; Lihua, Zhang; Rentian, Zhang

2010-06-01

According to different processes of tides and peak-valley electricity prices, this paper determines the optimal start up time in pumping station's 24 hours operation between the rating state and adjusting blade angle state respectively based on the optimization objective function and optimization model for single-unit pump's 24 hours operation taking JiangDu No.4 Pumping Station for example. In the meantime, this paper proposes the following regularities between optimal start up time of pumping station and the process of tides and peak-valley electricity prices each day within a month: (1) In the rating and adjusting blade angle state, the optimal start up time in pumping station's 24 hours operation which depends on the tide generation at the same day varies with the process of tides. There are mainly two kinds of optimal start up time which include the time at tide generation and 12 hours after it. (2) In the rating state, the optimal start up time on each day in a month exhibits a rule of symmetry from 29 to 28 of next month in the lunar calendar. The time of tide generation usually exists in the period of peak electricity price or the valley one. The higher electricity price corresponds to the higher minimum cost of water pumping at unit, which means that the minimum cost of water pumping at unit depends on the peak-valley electricity price at the time of tide generation on the same day. (3) In the adjusting blade angle state, the minimum cost of water pumping at unit in pumping station's 24 hour operation depends on the process of peak-valley electricity prices. And in the adjusting blade angle state, 4.85%˜5.37% of the minimum cost of water pumping at unit will be saved than that of in the rating state.

Quantitative measuring system for combustible gas with audible tick rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batz, J.E.

1979-09-04

Northern Illinois Gas Co.'s new gas-detection instrument is lightweight, portable, easy to use, and in compliance with industry standards as an intrinsically safe device. The instrument uses a semiconductor gas-sensor element energyzed with the regulated voltage source. Placed in the atmosphere to be tested, the detector generates a signal representative of the concentration of natural gas in the air. A meter displays the signal to determine whether the area is hazardous; a variable-repetition-rate blocking oscillator feeding a speaker responds to the signal, generating an audible tick rate useful in locating a leak.

3D simulation of an audible ultrasonic electrolarynx using difference waves.

PubMed

Mills, Patrick; Zara, Jason

2014-01-01

A total laryngectomy removes the vocal folds which are fundamental in forming voiced sounds that make speech possible. Although implanted prosthetics are commonly used in developed countries, simple handheld vibrating electrolarynxes are still common worldwide. These devices are easy to use but suffer from many drawbacks including dedication of a hand, mechanical sounding voice, and sound leakage. To address some of these drawbacks, we introduce a novel electrolarynx that uses vibro-acoustic interference of dual ultrasonic waves to generate an audible fundamental frequency. A 3D simulation of the principles of the device is presented in this paper.

FIREX mission requirements document for nonrenewable resources

NASA Technical Reports Server (NTRS)

Dixon, T.; Carsey, F.

1982-01-01

The proposed mission requirements and a proposed experimental program for satellite synthetic aperture radar (SAR) system named FIREX (Free-Flying Imaging Radar Experiment) for nonrenewable resources is described. The recommended spacecraft minimum SAR system is a C-band imager operating in four modes: (1) low look angle HH-polarized; (2) intermediate look angle, HH-polarized; (3) intermediate look angle, IIV-polarized; and (4) high look angle HH-polarized. This SAR system is complementary to other future spaceborne imagers such as the Thematic Mapper on LANDSAT-D. A near term aircraft SAR based research program is outlined which addresses specific mission design issues such as preferred incidence angles or polarizations for geologic targets of interest.

Design of an all-attitude flight control system to execute commanded bank angles and angles of attack

NASA Technical Reports Server (NTRS)

Burgin, G. H.; Eggleston, D. M.

1976-01-01

A flight control system for use in air-to-air combat simulation was designed. The input to the flight control system are commanded bank angle and angle of attack, the output are commands to the control surface actuators such that the commanded values will be achieved in near minimum time and sideslip is controlled to remain small. For the longitudinal direction, a conventional linear control system with gains scheduled as a function of dynamic pressure is employed. For the lateral direction, a novel control system, consisting of a linear portion for small bank angle errors and a bang-bang control system for large errors and error rates is employed.

MODULATION OF GALACTIC COSMIC RAYS OBSERVED AT L1 IN SOLAR CYCLE 23

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fludra, A., E-mail: Andrzej.Fludra@stfc.ac.uk

2015-01-20

We analyze a unique 15 yr record of galactic cosmic-ray (GCR) measurements made by the SOHO Coronal Diagnostic Spectrometer NIS detectors, recording integrated GCR numbers with energies above 1.0 GeV between 1996 July and 2011 June. We are able to closely reproduce the main features of the SOHO/CDS GCR record using the modulation potential calculated from neutron monitor data by Usoskin et al. The GCR numbers show a clear solar cycle modulation: they decrease by 50% from the 1997 minimum to the 2000 maximum of the solar cycle, then return to the 1997 level in 2007 and continue to rise, in 2009 Decembermore » reaching a level 25% higher than in 1997. This 25% increase is in contrast with the behavior of Ulysses/KET GCR protons extrapolated to 1 AU in the ecliptic plane, showing the same level in 2008-2009 as in 1997. The GCR numbers are inversely correlated with the tilt angle of the heliospheric current sheet. In particular, the continued increase of SOHO/CDS GCRs from 2007 until 2009 is correlated with the decrease of the minimum tilt angle from 30° in mid-2008 to 5° in late 2009. The GCR level then drops sharply from 2010 January, again consistent with a rapid increase of the tilt angle to over 35°. This shows that the extended 2008 solar minimum was different from the 1997 minimum in terms of the structure of the heliospheric current sheet.« less

16 CFR Table 1 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2014 CFR

2014-01-01

..., and side reflectors; entrance angle in degrees 0 10 up/down 20 left/right Pedal reflectors; entrance angle in degrees 0 10 up/down 20 left/right 0.2 27.0 18.0 9.0 7.5 6.0 3.0 0.3 6.0 4.8 2.4 1.5 .28 .20...

16 CFR Table 1 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2011 CFR

2011-01-01

..., and side reflectors; entrance angle in degrees 0 10 up/down 20 left/right Pedal reflectors; entrance angle in degrees 0 10 up/down 20 left/right 0.2 27.0 18.0 9.0 7.5 6.0 3.0 0.3 6.0 4.8 2.4 1.5 .28 .20...

16 CFR Table 1 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2010 CFR

2010-01-01

..., and side reflectors; entrance angle in degrees 0 10 up/down 20 left/right Pedal reflectors; entrance angle in degrees 0 10 up/down 20 left/right 0.2 27.0 18.0 9.0 7.5 6.0 3.0 0.3 6.0 4.8 2.4 1.5 .28 .20...

16 CFR Table 1 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2013 CFR

2013-01-01

..., and side reflectors; entrance angle in degrees 0 10 up/down 20 left/right Pedal reflectors; entrance angle in degrees 0 10 up/down 20 left/right 0.2 27.0 18.0 9.0 7.5 6.0 3.0 0.3 6.0 4.8 2.4 1.5 .28 .20...

16 CFR Table 1 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2012 CFR

2012-01-01

..., and side reflectors; entrance angle in degrees 0 10 up/down 20 left/right Pedal reflectors; entrance angle in degrees 0 10 up/down 20 left/right 0.2 27.0 18.0 9.0 7.5 6.0 3.0 0.3 6.0 4.8 2.4 1.5 .28 .20...

77 FR 73956 - Facilitating the Use of Microwave for Wireless Backhaul and Other Uses and Providing Additional...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-12

... incorrect and an entry to the table under Directional antennas in Sec. 101.115(b)(2) is incorrect. This... antennas. * * * * * (b) * * * (2) * * * Antenna Standards Maximum Minimum radiation suppression to angle in... \\1\\ antenna (included gain (dBi) 5[deg] 10[deg] 15[deg] 20[deg] 30[deg] 100[deg] 140[deg] angle in to...

Determining Metacarpophalangeal Flexion Angle Tolerance for Reliable Volumetric Joint Space Measurements by High-resolution Peripheral Quantitative Computed Tomography.

PubMed

Tom, Stephanie; Frayne, Mark; Manske, Sarah L; Burghardt, Andrew J; Stok, Kathryn S; Boyd, Steven K; Barnabe, Cheryl

2016-10-01

The position-dependence of a method to measure the joint space of metacarpophalangeal (MCP) joints using high-resolution peripheral quantitative computed tomography (HR-pQCT) was studied. Cadaveric MCP were imaged at 7 flexion angles between 0 and 30 degrees. The variability in reproducibility for mean, minimum, and maximum joint space widths and volume measurements was calculated for increasing degrees of flexion. Root mean square coefficient of variance values were < 5% under 20 degrees of flexion for mean, maximum, and volumetric joint spaces. Values for minimum joint space width were optimized under 10 degrees of flexion. MCP joint space measurements should be acquired at < 10 degrees of flexion in longitudinal studies.

An analysis of the impact of cabin floor angle restrictions on L/D for a typical supersonic transport

NASA Technical Reports Server (NTRS)

Radkey, R. L.

1974-01-01

High floor angles at cruise have been identified as a significant problem facing airline and public acceptance of a supersonic transport. In order to explore the relationship between cruise performances and floor angle, four related wing-fuselage design and integration studies have been conducted. The studies were: (1) a fuselage camber study in which perturbations in the fuselage camber distribution were examined with a baseline wing, (2) a wing optimization study in which wings were optimized for minimum drag at C sub L's less than the design C sub L. These wings were optimized as wing planform camber surfaces alone and evaluated with a baseline fuselage, (3) a second wing optimization study in which wings were optimized for minimum drag at C sub L's less than the design C sub L but for this study the wings were optimized in the presence of the baseline fuselage, and (4) a third wing optimization study in which wings were optimized for minmum drag subject to C sub M constraints designed to produce more positive C sub MO's, thereby reducing trim drag. The studies indicated that it was not possible to both improve the aircraft cruise L/D and substantially reduce the cruise floor angle. The studies did indicate that the cruise floor angle could be reduced by reducing the fuselage incidence relative to the wing, but the reduction in floor angle was accompanied by a substantial reduction in L/D.

Dynamic stiffness of chemically and physically ageing rubber vibration isolators in the audible frequency range: Part 2—waveguide solution

NASA Astrophysics Data System (ADS)

Kari, Leif

2017-09-01

The dynamic stiffness of a chemically and physically ageing rubber vibration isolator in the audible frequency range is modelled as a function of ageing temperature, ageing time, actual temperature, time, frequency and isolator dimension. In particular, the dynamic stiffness for an axially symmetric, homogeneously aged rubber vibration isolator is derived by waveguides where the eigenmodes given by the dispersion relation for an infinite cylinder satisfying traction free radial surface boundary condition are matched to satisfy the displacement boundary conditions at the lateral surface ends of the finite rubber cylinder. The constitutive equations are derived in a companion paper (Part 1). The dynamic stiffness is calculated over the whole audible frequency range 20-20,000 Hz at several physical ageing times for a temperature history starting at thermodynamic equilibrium at +25°C and exposed by a sudden temperature step down to -60°C and at several chemical ageing times at temperature +25°C with simultaneous molecular network scission and reformation. The dynamic stiffness results are displaying a strong frequency dependence at a short physical ageing time, showing stiffness magnitude peaks and troughs, and a strong physical ageing time dependence, showing a large stiffness magnitude increase with the increased physical ageing time, while the peaks and troughs are smoothed out. Likewise, stiffness magnitude peaks and troughs are frequency-shifted with increased chemical ageing time. The developed model is possible to apply for dynamic stiffness prediction of rubber vibration isolator over a broad audible frequency range under realistic environmental condition of chemical ageing, mainly attributed to oxygen exposure from outside and of physical ageing, primarily perceived at low-temperature steps.

Oak Ridge Reservation Public Warning Siren System Annual Test Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. F. Gee

2000-10-01

The full operational test of the Oak Ridge Reservation (ORR) Public Warning Siren System (PWSS) was successfully conducted on September 27, 2000. The annual test is a full-scale sounding of the individual siren systems around each of the three Department of Energy (DOE) sites in Oak Ridge, Tennessee. The purpose of the annual test is to demonstrate and validate the siren systems' ability to alert personnel outdoors in the Immediate Notification Zones (INZ) (approximately two miles) around each site. The success of this test is based on two critical functions of the siren system. The first function is system operability.more » The system is considered operable if 90% of the sirens are operational. System diagnostics and direct field observations were used to validate the operability of the siren systems. Based on the diagnostic results and field observations, greater than 90% of the sirens were considered operational. The second function is system audibility. The system is considered audible if the siren could be heard in the immediate notification zones around each of the three sites. Direct field observations, along with sound level measurements, were used to validate the audibility of the siren system. Based on the direct field observations and sound level measurements, the siren system was considered audible. The combination of field observations, system diagnostic status reports, and sound level measurements provided a high level of confidence that the system met and would meet operational requirements upon demand. As part of the overall system test, the Tennessee Emergency Management Agency (TEMA) activated the Emergency Alerting System (EAS), which utilized area radio stations to make announcements regarding the test and to remind residents of what to do in the event of an actual emergency.« less

The coherent interlayer resistance of a single, rotated interface between two stacks of AB graphite

NASA Astrophysics Data System (ADS)

Habib, K. M. Masum; Sylvia, Somaia S.; Ge, Supeng; Neupane, Mahesh; Lake, Roger K.

2013-12-01

The coherent, interlayer resistance of a misoriented, rotated interface between two stacks of AB graphite is determined for a variety of misorientation angles. The quantum-resistance of the ideal AB stack is on the order of 1 to 10 mΩ μm2. For small rotation angles, the coherent interlayer resistance exponentially approaches the ideal quantum resistance at energies away from the charge neutrality point. Over a range of intermediate angles, the resistance increases exponentially with cell size for minimum size unit cells. Larger cell sizes, of similar angles, may not follow this trend. The energy dependence of the interlayer transmission is described.

16 CFR Table 2 to Part 1512 - Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Minimum Candlepower per Incident Foot-Candle for Clear Reflector 1 2 Table 2 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION..., and side reflectors; entrance angle in degrees 30 left/right 40 left/right 50 left/right 0.2 8.0 7.0 6...

Spatial separation benefit for unaided and aided listening

PubMed Central

Ahlstrom, Jayne B.; Horwitz, Amy R.; Dubno, Judy R.

2013-01-01

Consonant recognition in noise was measured at a fixed signal-to-noise ratio as a function of low-pass-cutoff frequency and noise location in older adults fit with bilateral hearing aids. To quantify age-related differences, spatial benefit was assessed in younger and older adults with normal hearing. Spatial benefit was similar for all groups suggesting that older adults used interaural difference cues to improve speech recognition in noise equivalently to younger adults. Although amplification was sufficient to increase high-frequency audibility with spatial separation, hearing-aid benefit was minimal, suggesting that factors beyond simple audibility may be responsible for limited hearing-aid benefit. PMID:24121648

Passive pavement-mounted acoustical linguistic drive alert system and method

DOEpatents

Kisner, Roger A.; Anderson, Richard L.; Carnal, Charles L.; Hylton, James O.; Stevens, Samuel S.

2001-01-01

Systems and methods are described for passive pavement-mounted acoustical alert of the occupants of a vehicle. A method of notifying a vehicle occupant includes providing a driving medium upon which a vehicle is to be driven; and texturing a portion of the driving medium such that the textured portion interacts with the vehicle to produce audible signals, the textured portion pattern such that a linguistic message is encoded into the audible signals. The systems and methods provide advantages because information can be conveyed to the occupants of the vehicle based on the location of the vehicle relative to the textured surface.

System and Method for Providing a Real Time Audible Message to a Pilot

NASA Technical Reports Server (NTRS)

Johnson, Walter W. (Inventor); Lachter, Joel B. (Inventor); Koteskey, Robert W. (Inventor); Battiste, Vernol (Inventor)

2016-01-01

A system and method for providing information to a crew of the aircraft while in-flight. The system includes a module having: a receiver for receiving a message while in-flight; a filter having a set of screening parameters and operative to filter the message based on the set of screening parameters; and a converter for converting the message into an audible message. The message includes a pilot report having at least one of weather information, separation information, congestion information, flight deviation information and destination information. The message is sent to the aircraft by another aircraft or an air traffic controller.

Low Voltage MEMS Digital Loudspeaker Array Based on Thin-film PZT Actuators

NASA Astrophysics Data System (ADS)

Fanget, S.; Casset, F.; Dejaeger, R.; Maire, F.; Desloges, B.; Deutzer, J.; Morisson, R.; Bohard, Y.; Laroche, B.; Escato, J.; Leclere, Q.

This paper reports on the development of a Digital Loudspeaker Array (DLA) solution based on Pb(Zr0.52,Ti0.48)O3 (PZT) thin-film actuated membranes. These membranes called speaklets are arranged in a matrix and operate in a binary manner by emitting short pulses of sound pressure. Using the principle of additivity of pressures in the air, it is possible to reconstruct audible sounds. For the first time, electromechanical and acoustic characterizations are reported on a 256-MEMS-membranes DLA. Sounds audible as far as several meters from the loudspeaker have been generated using low voltage (8 V).

Evaluation of a multi-channel algorithm for reducing transient sounds.

PubMed

Keshavarzi, Mahmoud; Baer, Thomas; Moore, Brian C J

2018-05-15

The objective was to evaluate and select appropriate parameters for a multi-channel transient reduction (MCTR) algorithm for detecting and attenuating transient sounds in speech. In each trial, the same sentence was played twice. A transient sound was presented in both sentences, but its level varied across the two depending on whether or not it had been processed by the MCTR and on the "strength" of the processing. The participant indicated their preference for which one was better and by how much in terms of the balance between the annoyance produced by the transient and the audibility of the transient (they were told that the transient should still be audible). Twenty English-speaking participants were tested, 10 with normal hearing and 10 with mild-to-moderate hearing-impairment. Frequency-dependent linear amplification was provided for the latter. The results for both participant groups indicated that sounds processed using the MCTR were preferred over the unprocessed sounds. For the hearing-impaired participants, the medium and strong settings of the MCTR were preferred over the weak setting. The medium and strong settings of the MCTR reduced the annoyance produced by the transients while maintaining their audibility.

The Audible Pop from Thoracic Spine Thrust Manipulation and Its Relation to Short-Term Outcomes in Patients with Neck Pain

PubMed Central

Cleland, Joshua A.; Flynn, Timothy W.; Childs, John D.; Eberhart, Sarah

2007-01-01

Clinicians routinely consider the success of a thrust manipulation technique based on the presence or absence of an audible pop despite the lack of evidence suggesting that this pop is associated with improved outcomes. The purpose of this study was to determine the relationship between the number of audible pops with thoracic spinal manipulation and improvement in pain and function in patients with mechanical neck pain. In this prospective cohort study, 78 patients referred to physical therapy with mechanical neck pain underwent a standardized examination and thoracic spine manipulation treatment protocol. All patients were treated with a total of 6 thrust manipulation techniques directed to the thoracic spine followed by a basic cervical range of motion exercise. The treating clinician recorded the presence or absence of a pop during each manipulation. Outcomes were assessed at a 2–4 day follow-up with an 11-point numeric pain rating (NPRS), the Neck Disability Index, the patient Global Rating of Change (GROC), and measurements of cervical range of motion (CROM). The relationship between the number of pops and change scores for pain, disability, and CROM was first examined using Pearson correlation coefficients. Individuals were then categorized as having received ≤3 or >3 pops. Repeated measures analyses of variance were used to examine whether achievement of >3 pops resulted in improved outcome. Seventy-eight patients with a mean age of 42 (SD 11.3) years participated in the study. Pearson correlation coefficients revealed no significant correlation existed between the number of pops and outcomes with the exception of 3 of the 6 CROM measurements, which were inversely related. There was no significant interaction for group X time for any of the dependent measures (P>0.05). The odds ratio for patients experiencing dramatic improvement was in favor of the group experiencing ≤3 pops but this was not clinically meaningful (1.3: 95% CI 0.46, 3.7). The results of this analysis provide preliminary evidence for the hypothesis that there is no relationship between the number of audible pops during thoracic spine thrust manipulation and clinically meaningful improvements in pain, disability, or CROM in patients with mechanical neck pain. Additionally, a greater number of audible pops experienced was not associated with a dramatic improvement with manipulation treatment. PMID:19066662

Heat transfer from an oxidized large copper surface to liquid helium: Dependence on surface orientation and treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iwamoto, A.; Mito, T.; Takahata, K.

Heat transfer of large copper plates (18 x 76 mm) in liquid helium has been measured as a function of orientation and treatment of the heat transfer surface. The results relate to applications of large scale superconductors. In order to clarify the influence of the area where the surface treatment peels off, the authors studied five types of heat transfer surface areas including: (a) 100% polished copper sample, (b) and (c) two 50% oxidized copper samples having different patterns of oxidation, (d) 75% oxidized copper sample, (e) 90% oxidized copper sample, and (f) 100% oxidized copper sample. They observed thatmore » the critical heat flux depends on the heat transfer surface orientation. The critical heat flux is a maximum at angles of 0{degrees} - 30{degrees} and decreases monotonically with increasing angles above 30{degrees}, where the angle is taken in reference to the horizontal axis. On the other hand, the minimum heat flux is less dependent on the surface orientation. More than 75% oxidation on the surface makes the critical heat flux increase. The minimum heat fluxes of the 50 and 90% oxidized Cu samples approximately agree with that of the 100% oxidized Cu sample. Experiments and calculations show that the critical and the minimum heat fluxes are a bilinear function of the fraction of oxidized surface area.« less

Improved Time-Lapsed Angular Scattering Microscopy of Single Cells

NASA Astrophysics Data System (ADS)

Cannaday, Ashley E.

By measuring angular scattering patterns from biological samples and fitting them with a Mie theory model, one can estimate the organelle size distribution within many cells. Quantitative organelle sizing of ensembles of cells using this method has been well established. Our goal is to develop the methodology to extend this approach to the single cell level, measuring the angular scattering at multiple time points and estimating the non-nuclear organelle size distribution parameters. The diameters of individual organelle-size beads were successfully extracted using scattering measurements with a minimum deflection angle of 20 degrees. However, the accuracy of size estimates can be limited by the angular range detected. In particular, simulations by our group suggest that, for cell organelle populations with a broader size distribution, the accuracy of size prediction improves substantially if the minimum angle of detection angle is 15 degrees or less. The system was therefore modified to collect scattering angles down to 10 degrees. To confirm experimentally that size predictions will become more stable when lower scattering angles are detected, initial validations were performed on individual polystyrene beads ranging in diameter from 1 to 5 microns. We found that the lower minimum angle enabled the width of this delta-function size distribution to be predicted more accurately. Scattering patterns were then acquired and analyzed from single mouse squamous cell carcinoma cells at multiple time points. The scattering patterns exhibit angular dependencies that look unlike those of any single sphere size, but are well-fit by a broad distribution of sizes, as expected. To determine the fluctuation level in the estimated size distribution due to measurement imperfections alone, formaldehyde-fixed cells were measured. Subsequent measurements on live (non-fixed) cells revealed an order of magnitude greater fluctuation in the estimated sizes compared to fixed cells. With our improved and better-understood approach to single cell angular scattering, we are now capable of reliably detecting changes in organelle size predictions due to biological causes above our measurement error of 20 nm, which enables us to apply our system to future studies of the investigation of various single cell biological processes.

Rotation of the optical polarization angle associated with the 2008 γ-ray flare of blazar W Comae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sorcia, Marco; Benítez, Erika; Cabrera, José I.

2014-10-10

An R-band photopolarimetric variability analysis of the TeV bright blazar W Comae between 2008 February 28 and 2013 May 17 is presented. The source showed a gradual tendency to decrease its mean flux level with a total change of 3 mJy. A maximum and minimum brightness states in the R band of 14.25 ± 0.04 and 16.52 ± 0.1 mag, respectively, were observed, corresponding to a maximum variation of ΔF = 5.40 mJy. We estimated a minimum variability timescale of Δt = 3.3 days. A maximum polarization degree P = 33.8% ± 1.6%, with a maximum variation of ΔP =more » 33.2%, was found. One of our main results is the detection of a large rotation of the polarization angle from 78° to 315° (Δθ ∼ 237°) that coincides in time with the γ-ray flare observed in 2008 June. This result indicates that both optical and γ-ray emission regions could be co-spatial. During this flare, a correlation between the R-band flux and polarization degree was found with a correlation coefficient of r {sub F} {sub –} {sub p} = 0.93 ± 0.11. From the Stokes parameters, we infer the existence of two optically thin synchrotron components that contribute to the polarized flux. One of them is stable with a constant polarization degree of 11%. Assuming a shock-in jet model during the 2008 flare, we estimated a maximum Doppler factor δ {sub D} ∼ 27 and a minimum of δ {sub D} ∼ 16; a minimum viewing angle of the jet ∼2.°0; and a magnetic field B ∼ 0.12 G.« less

Rotated grating coupled surface plasmon resonance on wavelength-scaled shallow rectangular gratings

NASA Astrophysics Data System (ADS)

Szalai, A.; Szekeres, G.; Balázs, J.; Somogyi, A.; Csete, Maria

2013-09-01

Theoretical investigation of rotated grating coupling phenomenon was performed on a multilayer comprising 416-nmperiodic shallow rectangular polymer grating on bimetal film made of gold and silver layers. During the multilayer illumination by 532 nm wavelength p-polarized light the polar and azimuthal angles were varied. In presence of 0-35 nm, 0-50 nm and 15-50 nm thick polymer-layers at the valleys and hills splitting was observed on the dual-angle dependent reflectance in two regions: (i) close to 0° azimuthal angle corresponding to incidence plane parallel to the periodic pattern (P-orientation); and (ii) around ~33.5°/29°/30° azimuthal angle (C-orientation), in agreement with our previous experimental studies. The near-field study revealed that in P-orientation the E-field is enhanced at the glass side with p/2 periodicity at the first minimum appearing at 49°/50°/52° polar angles, and comprises maxima below both the valleys and hills; while E-field enhancement is observable both at the glass and polymer side with p-periodicity at the second minimum developing at 55°/63/64° tilting, comprising maxima intermittently below the valleys or above the hills. In Corientation coupled plasmonic modes are observable, involving modes propagating along the valleys at the secondary maxima appearing at ~35°/32°/32° azimuthal and ~49°/51°/56° polar angles, while modes confined along the polymer hills are observable at the primary minima, which are coupled most strongly at the ~31.5°/25°/28° azimuthal and ~55°/63°/66° polar angles. The secondary peak observable in C-orientation is proposed for biosensing applications, since the supported modes are confined along the valleys, where biomolecules prefer to attach.

Role of macular hole angle in macular hole closure.

PubMed

Chhablani, Jay; Khodani, Mitali; Hussein, Abdullah; Bondalapati, Sailaja; Rao, Harsha B; Narayanan, Raja; Sudhalkar, Aditya

2015-12-01

To evaluate correlation of various spectral-domain optical coherence tomography (SD-OCT) parameters including macular hole angle as well as various indices with anatomical and visual outcomes after idiopathic macular hole repair surgery. Retrospective study of 137 eyes of 137 patients who underwent idiopathic macular hole repair surgery between January 2008 and January 2014 was performed. Various qualitative parameters such as presence of vitreomacular traction, epiretinal membrane and cystic edges at the macular hole as well as quantitative parameters such as maximum diameter on the apex of the hole, minimum diameter between edges, nasal and temporal vertical height, longest base diameter and macular hole angle between the retinal edge and the retinal pigment epithelium were noted. Indices including hole form factor, Macular Hole Index (MHI), Diameter Hole Index and Tractional Hole Index (THI) were calculated. Univariate and multivariate regression analysis was performed separately for final visual acuity (VA) and type of closure as dependent variable in relation to SD-OCT parameters as independent variables. On multivariate regression only minimum diameter between edges (p≤0.01) and longest base diameter (p≤0.03) were correlated significantly with both, type 1 closure and final VA. Among the indices, significant correlation of MHI (p=0.009) was noted with type of closure and that of THI with final VA (p=0.017). Our study shows no significant correlation between macular hole angle and hole closure. Minimum diameter between the edges and longest diameter of the hole are best predictors of hole closure and postoperative VA. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Running Technique is an Important Component of Running Economy and Performance

PubMed Central

FOLLAND, JONATHAN P.; ALLEN, SAM J.; BLACK, MATTHEW I.; HANDSAKER, JOSEPH C.; FORRESTER, STEPHANIE E.

2017-01-01

ABSTRACT Despite an intuitive relationship between technique and both running economy (RE) and performance, and the diverse techniques used by runners to achieve forward locomotion, the objective importance of overall technique and the key components therein remain to be elucidated. Purpose This study aimed to determine the relationship between individual and combined kinematic measures of technique with both RE and performance. Methods Ninety-seven endurance runners (47 females) of diverse competitive standards performed a discontinuous protocol of incremental treadmill running (4-min stages, 1-km·h−1 increments). Measurements included three-dimensional full-body kinematics, respiratory gases to determine energy cost, and velocity of lactate turn point. Five categories of kinematic measures (vertical oscillation, braking, posture, stride parameters, and lower limb angles) and locomotory energy cost (LEc) were averaged across 10–12 km·h−1 (the highest common velocity < velocity of lactate turn point). Performance was measured as season's best (SB) time converted to a sex-specific z-score. Results Numerous kinematic variables were correlated with RE and performance (LEc, 19 variables; SB time, 11 variables). Regression analysis found three variables (pelvis vertical oscillation during ground contact normalized to height, minimum knee joint angle during ground contact, and minimum horizontal pelvis velocity) explained 39% of LEc variability. In addition, four variables (minimum horizontal pelvis velocity, shank touchdown angle, duty factor, and trunk forward lean) combined to explain 31% of the variability in performance (SB time). Conclusions This study provides novel and robust evidence that technique explains a substantial proportion of the variance in RE and performance. We recommend that runners and coaches are attentive to specific aspects of stride parameters and lower limb angles in part to optimize pelvis movement, and ultimately enhance performance. PMID:28263283

Tables for Supersonic Flow Around Right Circular Cones at Small Angle of Attack

NASA Technical Reports Server (NTRS)

Sims, Joseph L.

1964-01-01

The solution of supersonic flow fields by the method of characteristics requires that starting conditions be known. Ferri, in reference 1, developed a method-of-characteristics solution for axially symmetric bodies of revolution at small angles of attack. With computing machinery that is now available, this has become a feasible method for computing the aerodynamic characteristics of bodies near zero angle of attack. For sharp-nosed bodies of revolution, the required starting line may be obtained by computing the flow field about a cone at a small angle of attack. This calculation is readily performed using Stone's theory in reference 2. Some solutions of this theory are available in reference 3. However, the manner in which these results are presented, namely in a wind-fixed coordinate system, makes their use somewhat cumbersome. Additionally, as pointed out in reference 4, the flow component perpendicular to the meridian planes was computed incorrectly. The results contained herein have been computed in the same basic manner as those of reference 3 with the correct velocity normal to the meridian planes. Also, all results have been transferred into the body-fixed coordinate system. Therefore, the values tabulated herein may be used, in conjunction with the respective zero-angle-of-attack results of reference 5, as starting conditions for the method-of-characteristics solution of the flow field about axially symmetric bodies of revolution at small angles of attack. As in the zero-angle-of-attack case (ref. 5) the present results have been computed using the ideal gas value of 1.4 for the ratio of the specific heats of air. Solutions are given for cone angles from 2.5 deg to 30 deg in increments of 2.5 deg. For each cone angle, results were computed for a constant series of free-stream Mach numbers from 1.5 to 20. In addition, a solution was computed which yielded the minimum free-stream Mach number for a completely supersonic conical flow field. For cone angles of 27.5 deg and 30 deg, this minimum free-stream Mach number was above 1.5. Consequently, solutions at this Mach number were not computed for these two cone angles.

Canine sacroiliac luxation: anatomic study of the craniocaudal articular surface angulation of the sacrum to define a safe corridor in the dorsal plane for placement of screws used for fixation in lag fashion.

PubMed

Bowlt, Kelly L; Shales, Christopher J

2011-01-01

To define a safe corridor in the dorsal plane relative to the articular surface for placement of a single screw in lag fashion to achieve stabilization of sacroiliac luxation in the dog. Cadaveric study. Dorsoventral radiographs of denuded canine sacra (n=49) were taken to determine the safe corridor in the craniocaudal plane, and the maximum, optimum and minimum angles were calculated that would allow a screw inserted in lag fashion to engage at least 60% of the width of the sacral body without cranial or caudal penetration through the bone. The mean safe corridor in the dorsal plane is ∼24° wide. Mean craniocaudal minimum, optimum and maximum drill angles from the drill start point were 88°, 100°, and 111° from the articular surface, respectively. No single angle will completely avoid risk of screw penetration beyond the safe corridor cranially and caudally. There is sufficient anatomic variation between different canine sacra that a single angle cannot be recommended for screw placement in the dorsal plane. A standard angle cannot be recommended for screw placement in lag fashion within the canine sacrum in the dorsal plane. Because of the narrow width of the safe corridor, preoperative measurements on radiographs are recommended and a range of angled drill guides may be useful to decrease surgeon margin of error. © Copyright 2010 by The American College of Veterinary Surgeons.

Experimental and analytical studies of a true airspeed sensor

NASA Technical Reports Server (NTRS)

Goglia, G. L.; Shen, J. Y.

1983-01-01

A true airspeed sensor based on the precession of a vortex whistle for sensing airspeeds up to 321.9 km/hr (200 mph). In an attempt to model the complicated fluid mechanics of the vortex precession, three dimensional, inviscid, unsteady, incompressible fluid flow was studied by using the hydrodynamical linearized stability theory. The temporal stability approach was used to derive the relationship between the true airspeed and frequency response. The results show that the frequency response is linearly proportional to the airspeed. A computer program was developed to obtain the numerical solution. Computational results for various parameters were obtained. The designed sensor basically consisted of a vortex tube, a swirler, and a transducer system. A microphone converted the audible tone to an electronic frequency signal. Measurements for both the closed conduit tests and wind tunnel tests were recorded. For a specific flow rate or airspeed, larger exit swirler angles produced higher frequencies. For a smaller cross sectional area in the precessional flow region, the frequency was higher. It was observed that as the airspeed was increased the Strouhal number remained constant.

Investigating locomotion of dairy cows by use of high speed cinematography.

PubMed

Herlin, A H; Drevemo, S

1997-05-01

The longterm influence of management systems on the locomotion of 17 dairy cows was investigated by high speed cinematography (100 frames/s) and kinematic analysis. Angular patterns and hoof trajectories of the left fore- and hindlimbs are presented and statistics made of occurring minimum and maximum angles. At the recording, 3 cows had been kept in tie-stalls (TI) and 6 cows in cubicles (CI) for a consecutive time of about 2.5 years while 8 cows had been kept on grass for about 3 months. Four of the grazing cows had earlier been kept in cubicles (CG) and 4 in tie-stalls (TG) during earlier off grazing seasons together with TI and CI cows. The CI cows had a smaller maximum angle of the elbow joint compared to TI, TG and CG cows. The hock joint angle of the CI cows was less flexed during the stance phase than in TI and CG cows while the minimum angle during the swing phase was greater in the TI and CI cows compared to TG and CG cows. Pastured cows (TG and CG) had a less pronounced flexion of the fetlock joint angle during the stance compared to cows kept indoors (TI and CI). The results suggest that slatted floor and lack of exercise during summer grazing may affect locomotion. This is indicated by restrictions in the movements of the elbow and hock joints and in less fetlock joint flexion at full support.

Characterization of Dilatant Shear Bands in Castlegate Sandstone Using Micro-Computed Tomography

NASA Astrophysics Data System (ADS)

Rosenthal, R. E.; Issen, K. A.; Richards, M. C.; Ingraham, M. D.

2016-12-01

Deformation bands in granular rock are thin tabular zones of localized shear and/or volumetric strain, which affect permeability and can impact fluid flow, extraction and storage. The present work characterizes dilatant shear bands formed in Castlegate sandstone (a high porosity reservoir analog) during true triaxial laboratory testing (Ingraham et al., 2013a) at low mean stresses. X-ray micro-computed tomography (micro-CT) scans produced 3-dimensional voxel files containing density information of tested specimens. Micro-CT data were thresholded to extract the least dense voxels, corresponding to pore space and localized dilation. Plane fits were determined by a custom algorithm that calculated the angle between the band normal and maximum compression direction. For tests at the same mean stress, the band angle is lower when intermediate principal stress approaches minimum compression and higher when it approaches maximum compression. Micro-CT band angles were compared to angles from the specimen jackets (Ingraham et al., 2013a), and band angles from plane fits through located acoustic emissions (AE) events (Ingraham et al. 2013b). For non-axisymmetric stress states (three unique principal stresses), one primary dilatant shear band formed in each specimen. Occasionally, secondary bands traversing part of the specimen were also identified. The principal band angles from the micro-CT scans were on average within 3 degrees of the jacket angles and within 9 degrees of AE angles. For axisymmetric stress states (intermediate principal stress equal to maximum or minimum compression) micro-CT results reveal multiple conjugate and/or parallel bands. Each jacket angle correlated to a micro-CT angle within 4 degrees. Micro-CT results also reveal that, regardless of stress state, each band is comprised of a network of interconnected pore space pathways meandering between grain clusters, as opposed to an opening fracture/joint. Ingraham MD, KA Issen, DJ Holcomb, 2013a, J. Geophys. Res. Solid Earth, Vol. 118, pp. 536-552, doi:10.1002/jgrb.50084. Ingraham MD, KA Issen, DJ Holcomb, 2013b, Acta Geotech., Vol. 8, Iss. 6, pp. 645-663, DOI: 10.1007/s11440-013-0275-y.

Performance evaluation of the inverse dynamics method for optimal spacecraft reorientation

NASA Astrophysics Data System (ADS)

Ventura, Jacopo; Romano, Marcello; Walter, Ulrich

2015-05-01

This paper investigates the application of the inverse dynamics in the virtual domain method to Euler angles, quaternions, and modified Rodrigues parameters for rapid optimal attitude trajectory generation for spacecraft reorientation maneuvers. The impact of the virtual domain and attitude representation is numerically investigated for both minimum time and minimum energy problems. Owing to the nature of the inverse dynamics method, it yields sub-optimal solutions for minimum time problems. Furthermore, the virtual domain improves the optimality of the solution, but at the cost of more computational time. The attitude representation also affects solution quality and computational speed. For minimum energy problems, the optimal solution can be obtained without the virtual domain with any considered attitude representation.

Development of micro-electromechanical system (MEMS) cochlear biomodel

NASA Astrophysics Data System (ADS)

Ngelayang, Thailis Bounya Anak; Latif, Rhonira

2015-05-01

Human cochlear is undeniably one of the most amazing organs in human body. The functional mechanism is very unique in terms of its ability to convert the sound waves in the form of mechanical vibrations into the electrical nerve impulses. It is known that the normal human auditory system can perceive the audible frequency range between 20 Hz to 20 kHz. Scientists have conducted several researches trying to build the artificial basilar membrane in the human cochlea (cochlear biomodel). Micro-electromechanical system (MEMS) is one of the potential inventions that have the ability to mimic the active behavior of the basilar membrane. In this paper, an array of MEMS bridge beams that are mechanically sensitive to the perceived audible frequency has been proposed. An array of bridge bridge beams with 0.5 µm thickness and length varying from 200 µm to 2000 µm have been designed operate within the audible frequency range. In the bridge beams design, aluminium (Al), copper (Cu), tantalum (Ta) and platinum (Pt) have considered as the material for the bridge beam structure. From the finite element (FE) and lumped element (LE) models of the MEMS bridge beams, platinum has been found to be the best material for the cochlear biomodel design, closely mimicking the basilar membrane.

Cortical Auditory Evoked Potentials Reveal Changes in Audibility with Nonlinear Frequency Compression in Hearing Aids for Children: Clinical Implications

PubMed Central

Ching, Teresa Y. C.; Zhang, Vicky W.; Hou, Sanna; Van Buynder, Patricia

2016-01-01

Hearing loss in children is detected soon after birth via newborn hearing screening. Procedures for early hearing assessment and hearing aid fitting are well established, but methods for evaluating the effectiveness of amplification for young children are limited. One promising approach to validating hearing aid fittings is to measure cortical auditory evoked potentials (CAEPs). This article provides first a brief overview of reports on the use of CAEPs for evaluation of hearing aids. Second, a study that measured CAEPs to evaluate nonlinear frequency compression (NLFC) in hearing aids for 27 children (between 6.1 and 16.8 years old) who have mild to severe hearing loss is reported. There was no significant difference in aided sensation level or the detection of CAEPs for /g/ between NLFC on and off conditions. The activation of NLFC was associated with a significant increase in aided sensation levels for /t/ and /s/. It also was associated with an increase in detection of CAEPs for /t/ and /s/. The findings support the use of CAEPs for checking audibility provided by hearing aids. Based on the current data, a clinical protocol for using CAEPs to validate audibility with amplification is presented. PMID:27587920

Measures for assessing architectural speech security (privacy) of closed offices and meeting rooms.

PubMed

Gover, Bradford N; Bradley, John S

2004-12-01

Objective measures were investigated as predictors of the speech security of closed offices and rooms. A new signal-to-noise type measure is shown to be a superior indicator for security than existing measures such as the Articulation Index, the Speech Intelligibility Index, the ratio of the loudness of speech to that of noise, and the A-weighted level difference of speech and noise. This new measure is a weighted sum of clipped one-third-octave-band signal-to-noise ratios; various weightings and clipping levels are explored. Listening tests had 19 subjects rate the audibility and intelligibility of 500 English sentences, filtered to simulate transmission through various wall constructions, and presented along with background noise. The results of the tests indicate that the new measure is highly correlated with sentence intelligibility scores and also with three security thresholds: the threshold of intelligibility (below which speech is unintelligible), the threshold of cadence (below which the cadence of speech is inaudible), and the threshold of audibility (below which speech is inaudible). The ratio of the loudness of speech to that of noise, and simple A-weighted level differences are both shown to be well correlated with these latter two thresholds (cadence and audibility), but not well correlated with intelligibility.

Surface response of a viscoelastic medium to subsurface acoustic sources with application to medical diagnosis

NASA Astrophysics Data System (ADS)

Royston, Thomas J.; Yazicioglu, Yigit; Loth, Francis

2003-02-01

The response at the surface of an isotropic viscoelastic medium to buried fundamental acoustic sources is studied theoretically, computationally and experimentally. Finite and infinitesimal monopole and dipole sources within the low audible frequency range (40-400 Hz) are considered. Analytical and numerical integral solutions that account for compression, shear and surface wave response to the buried sources are formulated and compared with numerical finite element simulations and experimental studies on finite dimension phantom models. It is found that at low audible frequencies, compression and shear wave propagation from point sources can both be significant, with shear wave effects becoming less significant as frequency increases. Additionally, it is shown that simple closed-form analytical approximations based on an infinite medium model agree well with numerically obtained ``exact'' half-space solutions for the frequency range and material of interest in this study. The focus here is on developing a better understanding of how biological soft tissue affects the transmission of vibro-acoustic energy from biological acoustic sources below the skin surface, whose typical spectral content is in the low audible frequency range. Examples include sound radiated from pulmonary, gastro-intestinal and cardiovascular system functions, such as breath sounds, bowel sounds and vascular bruits, respectively.

Development of micro-electromechanical system (MEMS) cochlear biomodel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ngelayang, Thailis Bounya Anak; Latif, Rhonira

Human cochlear is undeniably one of the most amazing organs in human body. The functional mechanism is very unique in terms of its ability to convert the sound waves in the form of mechanical vibrations into the electrical nerve impulses. It is known that the normal human auditory system can perceive the audible frequency range between 20 Hz to 20 kHz. Scientists have conducted several researches trying to build the artificial basilar membrane in the human cochlea (cochlear biomodel). Micro-electromechanical system (MEMS) is one of the potential inventions that have the ability to mimic the active behavior of the basilar membrane. Inmore » this paper, an array of MEMS bridge beams that are mechanically sensitive to the perceived audible frequency has been proposed. An array of bridge bridge beams with 0.5 µm thickness and length varying from 200 µm to 2000 µm have been designed operate within the audible frequency range. In the bridge beams design, aluminium (Al), copper (Cu), tantalum (Ta) and platinum (Pt) have considered as the material for the bridge beam structure. From the finite element (FE) and lumped element (LE) models of the MEMS bridge beams, platinum has been found to be the best material for the cochlear biomodel design, closely mimicking the basilar membrane.« less

Underwater noise from three types of offshore wind turbines: estimation of impact zones for harbor porpoises and harbor seals.

PubMed

Tougaard, Jakob; Henriksen, Oluf Damsgaard; Miller, Lee A

2009-06-01

Underwater noise was recorded from three different types of wind turbines in Denmark and Sweden (Middelgrunden, Vindeby, and Bockstigen-Valar) during normal operation. Wind turbine noise was only measurable above ambient noise at frequencies below 500 Hz. Total sound pressure level was in the range 109-127 dB re 1 microPa rms, measured at distances between 14 and 20 m from the foundations. The 1/3-octave noise levels were compared with audiograms of harbor seals and harbor porpoises. Maximum 1/3-octave levels were in the range 106-126 dB re 1 microPa rms. Maximum range of audibility was estimated under two extreme assumptions on transmission loss (3 and 9 dB per doubling of distance, respectively). Audibility was low for harbor porpoises extending 20-70 m from the foundation, whereas audibility for harbor seals ranged from less than 100 m to several kilometers. Behavioral reactions of porpoises to the noise appear unlikely except if they are very close to the foundations. However, behavioral reactions from seals cannot be excluded up to distances of a few hundred meters. It is unlikely that the noise reaches dangerous levels at any distance from the turbines and the noise is considered incapable of masking acoustic communication by seals and porpoises.

Longitudinal changes in speech recognition in older persons.

PubMed

Dubno, Judy R; Lee, Fu-Shing; Matthews, Lois J; Ahlstrom, Jayne B; Horwitz, Amy R; Mills, John H

2008-01-01

Recognition of isolated monosyllabic words in quiet and recognition of key words in low- and high-context sentences in babble were measured in a large sample of older persons enrolled in a longitudinal study of age-related hearing loss. Repeated measures were obtained yearly or every 2 to 3 years. To control for concurrent changes in pure-tone thresholds and speech levels, speech-recognition scores were adjusted using an importance-weighted speech-audibility metric (AI). Linear-regression slope estimated the rate of change in adjusted speech-recognition scores. Recognition of words in quiet declined significantly faster with age than predicted by declines in speech audibility. As subjects aged, observed scores deviated increasingly from AI-predicted scores, but this effect did not accelerate with age. Rate of decline in word recognition was significantly faster for females than males and for females with high serum progesterone levels, whereas noise history had no effect. Rate of decline did not accelerate with age but increased with degree of hearing loss, suggesting that with more severe injury to the auditory system, impairments to auditory function other than reduced audibility resulted in faster declines in word recognition as subjects aged. Recognition of key words in low- and high-context sentences in babble did not decline significantly with age.

Physiological and content considerations for a second low frequency channel for bass management, subwoofers, and low frequency enhancement (LFE)

NASA Astrophysics Data System (ADS)

Miller, Robert E. (Robin)

2005-04-01

Perception of very low frequencies (VLF) below 125 Hz reproduced by large woofers and subwoofers (SW), encompassing 3 octaves of the 10 regarded as audible, has physiological and content aspects. Large room acoustics and vibrato add VLF fluctuations, modulating audible carrier frequencies to >1 Hz. By convention, sounds below 90 Hz produce no interaural cues useful for spatial perception or localization, therefore bass management redirects the VLF range from main channels to a single (monaural) subwoofer channel, even if to more than one subwoofer. Yet subjects claim they hear a difference between a single subwoofer channel and two (stereo bass). If recordings contain spatial VLF content, is it possible physiologically to perceive interaural time/phase difference (ITD/IPD) between 16 and 125 Hz? To what extent does this perception have a lifelike quality; to what extent is it localization? If a first approximation of localization, would binaural SWs allow a higher crossover frequency (smaller satellite speakers)? Reported research supports the Jeffress model of ITD determination in brain structures, and extending the accepted lower frequency limit of IPD. Meanwhile, uncorrelated very low frequencies exist in all tested multi-channel music and movie content. The audibility, recording, and reproduction of uncorrelated VLF are explored in theory and experiments.

Detection Rates of Cortical Auditory Evoked Potentials at Different Sensation Levels in Infants with Sensory/Neural Hearing Loss and Auditory Neuropathy Spectrum Disorder

PubMed Central

Gardner-Berry, Kirsty; Chang, Hsiuwen; Ching, Teresa Y. C.; Hou, Sanna

2016-01-01

With the introduction of newborn hearing screening, infants are being diagnosed with hearing loss during the first few months of life. For infants with a sensory/neural hearing loss (SNHL), the audiogram can be estimated objectively using auditory brainstem response (ABR) testing and hearing aids prescribed accordingly. However, for infants with auditory neuropathy spectrum disorder (ANSD) due to the abnormal/absent ABR waveforms, alternative measures of auditory function are needed to assess the need for amplification and evaluate whether aided benefit has been achieved. Cortical auditory evoked potentials (CAEPs) are used to assess aided benefit in infants with hearing loss; however, there is insufficient information regarding the relationship between stimulus audibility and CAEP detection rates. It is also not clear whether CAEP detection rates differ between infants with SNHL and infants with ANSD. This study involved retrospective collection of CAEP, hearing threshold, and hearing aid gain data to investigate the relationship between stimulus audibility and CAEP detection rates. The results demonstrate that increases in stimulus audibility result in an increase in detection rate. For the same range of sensation levels, there was no difference in the detection rates between infants with SNHL and ANSD. PMID:27587922

Alpha particle condensation in {sup 12}C and nuclear rainbow scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohkubo, S.; Hirabayashi, Y.

2008-05-12

It is shown that the large radius of the Hoyle state of {sup 12}C with a dilute density distribution in an {alpha} particle condensate can be clearly seen in the shift of the rainbow angle (therefore the Airy minimum) to a larger angle in {alpha}+{sup 12}C rainbow scattering at the high energy region and prerainbow oscillations in {sup 3}He+{sup 12}C scattering at the lower energy region.

A Partially Saturated Constitutive Theory for Compacted Fills

DTIC Science & Technology

2004-06-01

degree of Doctor of Philosophy. COL James R. Rowan, EN , was Commander and Executive Director of ERDC, and Dr. James R. Houston was Director. CHAPTER...Reconsolidation Index CR Slope of the reconsolidation line Maximum Friction Angle of3 Friction Angle PHILIM traMaterial Ratio of minimum to maximum4 Phi Ratio PH ...Josa, A., (1988). "Un modelo elastoplastico para suelos no saturados," Tesis Doctorae, Universitat Politecnica de Catalunya, Barcelons, Spain. Lawton

Jet slurry erosion performance of composite clad and its characterization

NASA Astrophysics Data System (ADS)

B, Lohit R.; Horakeri, Gururaj S.; Bhovi, Prabakhar M.

2016-09-01

In the present work, development of composite cladding consists of Cr23C6 (chromium carbide) as reinforcement particles 20 wt. % in Ni-based matrix 80 wt. % on austenitic stainless steel through exposure of microwave radiation has been carried out. The jet slurry erosion test was performed on microwave composite clad. The functional performance of composite clad has been evaluated for different parametric conditions like varying impingement velocity and impact angle. The increasing weight loss trend was observed with time for the first 30 min. after that the individual trend decreased; at high impingement velocity and maximum impact angle. SEM micrographs of eroded clad samples at various impact angle and impingement velocity were discussed. The maximum weight loss occurred at 90° angle and velocity of 60 m/s, and minimum at 30° angle and velocity of 20 m/s.

Anomalous and Galactic Cosmic Ray Intensities at 1 AU During the Approach to the Cycle 24/25 Solar Minimum and Throughout the Last 20 Years

NASA Astrophysics Data System (ADS)

Leske, R. A.; Cummings, A. C.; Mewaldt, R. A.; Cohen, C.; Stone, E. C.; Wiedenbeck, M. E.

2017-12-01

Anomalous cosmic ray (ACR) intensities at 1 AU generally track galactic cosmic ray (GCR) intensities, but with differences between solar polarity cycles: at high rigidities, GCRs reach higher peak intensities during A<0 cycles, while ACRs have been higher at A>0 solar minima. At present, during the approach to an A>0 solar minimum, ACR oxygen above 8 MeV/nucleon as measured by the Advanced Composition Explorer (ACE) has already reached the peak intensities seen during the 2009 A<0 solar minimum, but is still 40% below the levels seen in 1997 during the last A>0 minimum. The GCR iron intensity at 300 MeV/nucleon, on the other hand, is presently comparable to that in 1997 but remains 10% below its record-setting 2009 value. Drift effects play an important role in the modulation of both ACRs and GCRs. Positively charged ions drift inward along the heliospheric current sheet (HCS) during A<0 cycles and their intensities are thus sensitive to the HCS tilt angle, which remained high for much of the last solar cycle. We have previously shown that both ACR and GCR intensities were significantly higher for a given HCS tilt angle during the 2000-2012 A<0 cycle than they were during the prior (1980-1990) A<0 cycle, and this trend appears to be continuing into the new A>0 cycle. But while GCR intensities in 2009 reached the highest levels recorded during the last 50 years, ACR intensities were only similar to those in the 1980s A<0 minimum. Factors such as a weaker interplanetary magnetic field, perhaps with a reduction in the ACR source strength or greater sensitivity of ACRs than GCRs to the HCS tilt angle, may account for the difference in their modulation behavior.We present 20 years of ACR and GCR intensity data acquired by ACE throughout two solar cycles, with emphasis on recent observations, and discuss possible reasons for the differences in the relative behavior of ACRs and GCRs in the different solar cycles.

Sensitivity of 30-cm mercury bombardment ion thruster characteristics to accelerator grid design

NASA Technical Reports Server (NTRS)

Rawlin, V. K.

1978-01-01

The design of ion optics for bombardment thrusters strongly influences overall performance and lifetime. The operation of a 30 cm thruster with accelerator grid open area fractions ranging from 43 to 24 percent, was evaluated and compared with experimental and theoretical results. Ion optics properties measured included the beam current extraction capability, the minimum accelerator grid voltage to prevent backstreaming, ion beamlet diameter as a function of radial position on the grid and accelerator grid hole diameter, and the high energy, high angle ion beam edge location. Discharge chamber properties evaluated were propellant utilization efficiency, minimum discharge power per beam amp, and minimum discharge voltage.

The Variance of Solar Wind Magnetic Fluctuations: Solutions and Further Puzzles

NASA Technical Reports Server (NTRS)

Roberts, D. A.; Goldstein, M. L.

2006-01-01

We study the dependence of the variance directions of the magnetic field in the solar wind as a function of scale, radial distance, and Alfvenicity. The study resolves the question of why different studies have arrived at widely differing values for the maximum to minimum power (approximately equal to 3:1 up to approximately equal to 20:1). This is due to the decreasing anisotropy with increasing time interval chosen for the variance, and is a direct result of the "spherical polarization" of the waves which follows from the near constancy of |B|. The reason for the magnitude preserving evolution is still unresolved. Moreover, while the long-known tendency for the minimum variance to lie along the mean field also follows from this view (as shown by Barnes many years ago), there is no theory for why the minimum variance follows the field direction as the Parker angle changes. We show that this turning is quite generally true in Alfvenic regions over a wide range of heliocentric distances. The fact that nonAlfvenic regions, while still showing strong power anisotropies, tend to have a much broader range of angles between the minimum variance and the mean field makes it unlikely that the cause of the variance turning is to be found in a turbulence mechanism. There are no obvious alternative mechanisms, leaving us with another intriguing puzzle.

AEROX: Computer program for transonic aircraft aerodynamics to high angles of attack. Volume 1: Aerodynamic methods and program users' guide

NASA Technical Reports Server (NTRS)

Axelson, J. A.

1977-01-01

The AEROX program estimates lift, induced-drag and pitching moments to high angles (typ. 60 deg) for wings and for wingbody combinations with or without an aft horizontal tail. Minimum drag coefficients are not estimated, but may be input for inclusion in the total aerodynamic parameters which are output in listed and plotted formats. The theory, users' guide, test cases, and program listing are presented.

Sound localization skills in children who use bilateral cochlear implants and in children with normal acoustic hearing

PubMed Central

Grieco-Calub, Tina M.; Litovsky, Ruth Y.

2010-01-01

Objectives To measure sound source localization in children who have sequential bilateral cochlear implants (BICIs); to determine if localization accuracy correlates with performance on a right-left discrimination task (i.e., spatial acuity); to determine if there is a measurable bilateral benefit on a sound source identification task (i.e., localization accuracy) by comparing performance under bilateral and unilateral listening conditions; to determine if sound source localization continues to improve with longer durations of bilateral experience. Design Two groups of children participated in this study: a group of 21 children who received BICIs in sequential procedures (5–14 years old) and a group of 7 typically-developing children with normal acoustic hearing (5 years old). Testing was conducted in a large sound-treated booth with loudspeakers positioned on a horizontal arc with a radius of 1.2 m. Children participated in two experiments that assessed spatial hearing skills. Spatial hearing acuity was assessed with a discrimination task in which listeners determined if a sound source was presented on the right or left side of center; the smallest angle at which performance on this task was reliably above chance is the minimum audible angle. Sound localization accuracy was assessed with a sound source identification task in which children identified the perceived position of the sound source from a multi-loudspeaker array (7 or 15); errors are quantified using the root-mean-square (RMS) error. Results Sound localization accuracy was highly variable among the children with BICIs, with RMS errors ranging from 19°–56°. Performance of the NH group, with RMS errors ranging from 9°–29° was significantly better. Within the BICI group, in 11/21 children RMS errors were smaller in the bilateral vs. unilateral listening condition, indicating bilateral benefit. There was a significant correlation between spatial acuity and sound localization accuracy (R2=0.68, p<0.01), suggesting that children who achieve small RMS errors tend to have the smallest MAAs. Although there was large intersubject variability, testing of 11 children in the BICI group at two sequential visits revealed a subset of children who show improvement in spatial hearing skills over time. Conclusions A subset of children who use sequential BICIs can acquire sound localization abilities, even after long intervals between activation of hearing in the first- and second-implanted ears. This suggests that children with activation of the second implant later in life may be capable of developing spatial hearing abilities. The large variability in performance among the children with BICIs suggests that maturation of sound localization abilities in children with BICIs may be dependent on various individual subject factors such as age of implantation and chronological age. PMID:20592615

Global Images of Trapped Ring Current Ions During Main Phase of 17 March 2015 Geomagnetic Storm as Observed by TWINS

NASA Technical Reports Server (NTRS)

Perez, J. D.; Goldstein, J.; McComas, D. J.; Valek, P.; Fok, Mei-Ching; Hwang, Kyoung-Joo

2016-01-01

A unique view of the trapped particles in the inner magnetosphere provided by energetic neutral atom (ENA) imaging is used to observe the dynamics of the spatial structure and the pitch angle anisotropy on a global scale during the last 6 h of the main phase of a large geomagnetic storm (minimum SYM-H 230 nT) that began on 17 March 2015. Ion flux and pressure anisotropy obtained from Two Wide-angle Imaging Neutral-atom Spectrometers (TWINS) ENA images are shown. The ion flux shows two peaks, an inner one at approximately radii 34 RE in the dusk-to-midnight sector and an outer peak at radii 89 RE prior to midnight. The inner peak is relatively stationary during the entire period with some intensification during the final steep decline in SYM-H to its minimum. The outer peak shows the significant temporal variation brightening and dimming and finally disappearing at the end of the main phase. The pressure anisotropy shows the expected perpendicular pitch angles inside of L 6 but shows parallel pitch angles at greater L values. This is interpreted as consistent with pitch angle-dependent drift as modeled in the Tsy05 magnetic field and Comprehensive Inner Magnetosphere-Ionosphere simulations. The TWINS results are compared directly with Radiation Belt Storm Probes Ion Composition Experiment (RBSPICE)-A measurements. Using 15 min snapshots of flux and pressure anisotropy from TWINS along the path of RBSPICE-A during the 6 h focused upon in this study, the essential features displayed in the TWINS global images are supported.

Measurement and interpretation of crustal deformation rates associated with postglacial rebound

NASA Technical Reports Server (NTRS)

Davis, James L.

1994-01-01

Analysis of Global Positioning System (GPS) data from two sites separated by horizontal distance of only approximately 2.2 m yielded phase residuals exhibiting a systematic elevation angle dependence. One of the two GPS antennas was mounted on an approximately 1 m high concrete pillar, and the other was mounted on a standard wooden tripod. We performed elevation angle cutoff tests with these data, and established that the vertical coordinate of site position was sensitive to the minimum elevation angle (elevation cutoff) of the data analyzed. For example, the vertical coordinate of site position changed by 9.7 plus or minus 0.8 mm when the minimum elevation angle was increased from 10 to 25. We performed simulations based on a simple (ray tracing) multipath model with a single horizontal reflector, and demonstrated that the elevation angle cutoff test results and the pattern of the residual versus elevation angle could be qualitatively reproduced if the reflector were located 0.1-0.2 m beneath the antenna phase center. We therefore, hypothesized that the source of the elevation-angle-dependent error were multipath reflections and scattering and that the horizontal surface of the pillar, located a distance of approximately 0.2 m beneath the antenna phase center, was the primary reflector. We tested this hypothesis by placing microwave absorbing material between the antenna and the pillar in a number of configurations and analyzed the changes in apparent position of the antenna. The results indicate that (1) the horizontal surface of the pillar is indeed the main reflector, (2) both the concrete and the metal plate embedded in the pillar are significant reflectors, and (3) the reflection can be reduced to a great degree by the use of microwave absorbing materials. These results have significant implications for the accuracy of global GPS geodetic tracking networks which use pillar-antenna configuration identical or similar to the one used here (at the Westford WFRD GPS site).

Time-resolved fluorescence of thioredoxin single-tryptophan mutants: modeling experimental results with minimum perturbation mapping

NASA Astrophysics Data System (ADS)

Silva, Norberto D., Jr.; Haydock, Christopher; Prendergast, Franklyn G.

1994-08-01

The time-resolved fluorescence decay of single tryptophan (Trp) proteins is typically described using either a distribution of lifetimes or a sum of two or more exponential terms. A possible interpretation for this fluorescence decay heterogeneity is the existence of different isomeric conformations of Trp about its (chi) +1) and (chi) +2) dihedral angles. Are multiple Trp conformations compatible with the remainder of the protein in its crystallographic configuration or do they require repacking of neighbor side chains? It is conceivable that isomers of the neighbor side chains interconvert slowly on the fluorescence timescale and contribute additional lifetime components to the fluorescence intensity. We have explored this possibility by performing minimum perturbation mapping simulations of Trp 28 and Trp 31 in thioredoxin (TRX) using CHARMm 22. Mappings of Trp 29 and Trp 31 give the TRX Trp residue energy landscape as a function of (chi) +1) and (chi) +2) dihedral angles. Time-resolved fluorescence intensity and anisotropy decay of mutant TRX (W28F and W31F) are measured and interpreted in light of the above simulations. Relevant observables, like order parameters and isomerization rates, can be derived from the minimum perturbation maps and compared with experiment.

Vortices for K-shell ionization of carbon by electron impact

NASA Astrophysics Data System (ADS)

Ward, S. J.; Macek, J. H.

2014-05-01

Using the Coulomb-Born approximation, we obtained a deep minimum in the TDCS for K-shell ionization of carbon by electron impact. The minimum is due to a vortex in the velocity field. We considered the electron to be ejected in the scattering plane, which we took to be the xz -plane. The minimum was obtained for the kinematics of an incident energy Ei = 1801 . 2 eV , scattering angle θf =4° , energy of ejected electron Ek = 5 . 5 eV , and angle of the ejected electron θk =239° . We analyzed the importance of various multipole components in an expansion of the Coulomb-Born T-matrix. We also considered the electron ejected out of the scattering plane for Ei = 1801 . 2 eV and θf =4° and located the positions of vortices for small but nonzero values of ky, the y - component of the momentum of the ejected electron. We constructed the vortex line for the kinematics of Ei = 1801 . 2 eV and θf =4° . S. J. W. and J. H. M. acknowledge support from NSF under grant no. PHYS- 0968638 and from D.O.E. under grant number DE-FG02-02ER15283, respectively.

2D tilting MEMS micro mirror integrating a piezoresistive sensor position feedback

NASA Astrophysics Data System (ADS)

Lani, S.; Bayat, D.; Despont, M.

2015-02-01

An integrated position sensor for a dual-axis electromagnetic tilting mirror is presented. This tilting mirror is composed of a silicon based mirror directly assembled on a silicon membrane supported by flexible beams. The position sensors are constituted by 4 Wheatstone bridges of piezoresistors which are fabricated by doping locally the flexible beams. A permanent magnet is attached to the membrane and the scanner is mounted above planar coils deposited on a ceramic substrate to achieve electromagnetic actuation. The performances of the piezoresistive sensors are evaluated by measuring the output signal of the piezoresistors as a function of the tilt of the mirror and the temperature. White light interferometry was performed for all measurement to measure the exact tilt angle. The minimum detectable angle with such sensors was 30µrad (around 13bits) in the range of the minimum resolution of the interferometer. The tilt reproducibility was 0.0186%, obtained by measuring the tilt after repeated actuations with a coil current of 50mA during 30 min and the stability over time was 0.05% in 1h without actuation. The maximum measured tilt angle was 6° (mechanical) limited by nonlinearity of the MEMS system.

Statistical analysis of midlatitude spread F using multi-station digisonde observations

NASA Astrophysics Data System (ADS)

Bhaneja, P.; Earle, G. D.; Bullett, T. W.

2018-01-01

A comprehensive statistical study of midlatitude spread F (MSF) is presented for five midlatitude stations in the North American sector. These stations include Ramey AFB, Puerto Rico (18.5°N, 67.1°W, -14° declination angle), Wallops Island, Virginia (37.95°N, 75.5°W, -11° declination angle), Dyess, Texas (32.4°N, 99.8°W, 6.9° declination angle), Boulder, Colorado (40°N, 105.3°W, 10° declination angle), and Vandenberg AFB, California (34.8°N, 120.5°W, 13° declination angle). Pattern recognition algorithms are used to determine the presence of both range and frequency spread F. Data from 1996 to 2011 are analyzed, covering all of Solar Cycle 23 and the beginning of Solar Cycle 24. Variations with respect to season and solar activity are presented, including the effects of the extended minimum between cycles 23 and 24.

A Symmetric Time-Varying Cluster Rate of Descent Model

NASA Technical Reports Server (NTRS)

Ray, Eric S.

2015-01-01

A model of the time-varying rate of descent of the Orion vehicle was developed based on the observed correlation between canopy projected area and drag coefficient. This initial version of the model assumes cluster symmetry and only varies the vertical component of velocity. The cluster fly-out angle is modeled as a series of sine waves based on flight test data. The projected area of each canopy is synchronized with the primary fly-out angle mode. The sudden loss of projected area during canopy collisions is modeled at minimum fly-out angles, leading to brief increases in rate of descent. The cluster geometry is converted to drag coefficient using empirically derived constants. A more complete model is under development, which computes the aerodynamic response of each canopy to its local incidence angle.

Extreme ultraviolet reflector

DOEpatents

Newnam, Brian E.

1990-01-01

A multi-faceted mirror forms a retroreflector for a resonator loop in a free electron laser (FEL) operating in the XUV (.lambda.=10-100 nm). The number of facets is determined by the angle-of-incidence needed to obtain total external reflectance (TER) from the facet surface and the angle through which the FEL beam is to be turned. Angles-of-incidence greater than the angle for TER may be used to increase the area of the beam incident on the surface and reduce energy absorption density. Suitable surface films having TER in the 10-100 nm range may be formed from a variety of materials, including Al, single-crystal Si, Ag, and Rh. One of the facets is formed as an off-axis conic section to collimate the output beam with minimum astigmatism.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajkumar, K.; Rajavel, K.; Cameron, D. C.

This paper reports the electrowetting properties of liquid droplet on superhydrophobic silicon nanowires with Atomic layer deposited (ALD) Al{sub 2}O{sub 3} as dielectric layer. Silicon wafer were etched by metal assisted wet chemical etching with silver as catalyst. ALD Al{sub 2}O{sub 3} films of 10nm thickness were conformally deposited over silicon nanowires. Al{sub 2}O{sub 3} dielectric film coated silicon nanowires was chemically modified with Trichloro (1H, 1H, 2H, 2H-perfluorooctyl) silane to make it superhydrophobic(SHP). The contact angle was measured and all the samples exhibited superhydrophobic nature with maximum contact angles of 163° and a minimum contact angle hysteresis of 6°.more » Electrowetting induced a maximum reversible decrease of the contact angle of 20°at 150V in air.« less

Aerodynamic Design of Axial-flow Compressors. Volume 2

NASA Technical Reports Server (NTRS)

1956-01-01

Available experimental two-dimensional-cascade data for conventional compressor blade sections are correlated. The two-dimensional cascade and some of the principal aerodynamic factors involved in its operation are first briefly described. Then the data are analyzed by examining the variation of cascade performance at a reference incidence angle in the region of minimum loss. Variations of reference incidence angle, total-pressure loss, and deviation angle with cascade geometry, inlet Mach number, and Reynolds number are investigated. From the analysis and the correlations of the available data, rules and relations are evolved for the prediction of the magnitude of the reference total-pressure loss and the reference deviation and incidence angles for conventional blade profiles. These relations are developed in simplified forms readily applicable to compressor design procedures.

Vowel perception by noise masked normal-hearing young adults

NASA Astrophysics Data System (ADS)

Richie, Carolyn; Kewley-Port, Diane; Coughlin, Maureen

2005-08-01

This study examined vowel perception by young normal-hearing (YNH) adults, in various listening conditions designed to simulate mild-to-moderate sloping sensorineural hearing loss. YNH listeners were individually age- and gender-matched to young hearing-impaired (YHI) listeners tested in a previous study [Richie et al., J. Acoust. Soc. Am. 114, 2923-2933 (2003)]. YNH listeners were tested in three conditions designed to create equal audibility with the YHI listeners; a low signal level with and without a simulated hearing loss, and a high signal level with a simulated hearing loss. Listeners discriminated changes in synthetic vowel tokens /smcapi e ɛ invv æ/ when F1 or F2 varied in frequency. Comparison of YNH with YHI results failed to reveal significant differences between groups in terms of performance on vowel discrimination, in conditions of similar audibility by using both noise masking to elevate the hearing thresholds of the YNH and applying frequency-specific gain to the YHI listeners. Further, analysis of learning curves suggests that while the YHI listeners completed an average of 46% more test blocks than YNH listeners, the YHI achieved a level of discrimination similar to that of the YNH within the same number of blocks. Apparently, when age and gender are closely matched between young hearing-impaired and normal-hearing adults, performance on vowel tasks may be explained by audibility alone.

Cortical Auditory Evoked Potentials in (Un)aided Normal-Hearing and Hearing-Impaired Adults

PubMed Central

Van Dun, Bram; Kania, Anna; Dillon, Harvey

2016-01-01

Cortical auditory evoked potentials (CAEPs) are influenced by the characteristics of the stimulus, including level and hearing aid gain. Previous studies have measured CAEPs aided and unaided in individuals with normal hearing. There is a significant difference between providing amplification to a person with normal hearing and a person with hearing loss. This study investigated this difference and the effects of stimulus signal-to-noise ratio (SNR) and audibility on the CAEP amplitude in a population with hearing loss. Twelve normal-hearing participants and 12 participants with a hearing loss participated in this study. Three speech sounds—/m/, /g/, and /t/—were presented in the free field. Unaided stimuli were presented at 55, 65, and 75 dB sound pressure level (SPL) and aided stimuli at 55 dB SPL with three different gains in steps of 10 dB. CAEPs were recorded and their amplitudes analyzed. Stimulus SNRs and audibility were determined. No significant effect of stimulus level or hearing aid gain was found in normal hearers. Conversely, a significant effect was found in hearing-impaired individuals. Audibility of the signal, which in some cases is determined by the signal level relative to threshold and in other cases by the SNR, is the dominant factor explaining changes in CAEP amplitude. CAEPs can potentially be used to assess the effects of hearing aid gain in hearing-impaired users. PMID:27587919

New orientation and accessibility option for persons with visual impairment: transportation applications for remote infrared audible signage.

PubMed

Crandall, William; Bentzen, Billie Louise; Myers, Linda; Brabyn, John

2001-05-01

BACKGROUND: For a blind or visually impaired person, a vital prerequisite to accessing any feature of the built environment is being able to find this feature. Braille signs, even where available, do not replace the functions of print signage because they cannot be read from a distance. Remotely readable infrared signs utilise spoken infrared message transmissions to label key environmental features, so that a blind person with a suitable receiver can locate and identify them from a distance. METHODS: Three problems that are among the most challenging and dangerous faced by blind travellers are negotiating complex transit stations, locating bus stops and safely and efficiently crossing light-controlled intersections. We report the results of human factors studies using a remote infrared audible sign system (RIAS), Talking Signs(R), in these critical tasks, examining issues such as the amount of training needed to use the system, its impact on performance and safety, benefits for different population subgroups and user opinions of its value. RESULTS: Results are presented in the form of both objective performance measures and in subjects' ratings of the usefulness of the system in performing these tasks. Findings are that blind people can quickly and easily learn to use remote infrared audible signage effectively and that its use improves travel safety, efficiency and independence.? CONCLUSIONS: The technology provides equal access to a wide variety of public facilities.

Analytical and numerical analysis of the slope of von Mises planar trusses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalina, M.; Frantík, P.

2016-06-08

In the present paper, there are presented post-critical stress states which will occur at loading by vertical shift of the top joint in the direction downwards. The formation of certain stress states depends on the size of the angle formed by a straight beam of the von Mises planar truss with horizontal plane. Numerical and analytical methods and their problems with finding the angle were described. The numerical solution applies the method of searching for a minimum of potential energy.

Diffraction effects on angular response of X-ray collimators

NASA Technical Reports Server (NTRS)

Blake, R. L.; Barrus, D. M.; Fenimore, E.

1976-01-01

Angular responses have been measured for X-ray collimators with half-widths ranging from minutes of arc down to 10 arcsec. In the seconds-of-arc range, diffraction peaks at off-axis angles can masquerade as side lobes of the collimator angular response. Measurements and qualitative physical arguments lead to a rule of thumb for collimator design; namely, the angle of first minimum in the Fraunhofer single-slit diffraction pattern should be less than one-fourth of the collimator geometrical full-width at half-maximum intensity.

DC conductivity of twisted bilayer graphene: Angle-dependent transport properties and effects of disorder

NASA Astrophysics Data System (ADS)

Andelković, M.; Covaci, L.; Peeters, F. M.

2018-03-01

The in-plane dc conductivity of twisted bilayer graphene is calculated using an expansion of the real-space Kubo-Bastin conductivity in terms of Chebyshev polynomials. We investigate within a tight-binding approach the transport properties as a function of rotation angle, applied perpendicular electric field, and vacancy disorder. We find that for high-angle twists, the two layers are effectively decoupled, and the minimum conductivity at the Dirac point corresponds to double the value observed in monolayer graphene. This remains valid even in the presence of vacancies, hinting that chiral symmetry is still preserved. On the contrary, for low twist angles, the conductivity at the Dirac point depends on the twist angle and is not protected in the presence of disorder. Furthermore, for low angles and in the presence of an applied electric field, we find that the chiral boundary states emerging between AB and BA regions contribute to the dc conductivity, despite the appearance of localized states in the AA regions. The results agree qualitatively with recent transport experiments in low-angle twisted bilayer graphene.

Single-mode fibers to single-mode waveguides coupling with minimum Fresnel back-reflection

NASA Astrophysics Data System (ADS)

Sneh, Anat; Ruschin, Shlomo; Marom, Emanuel

1991-04-01

Slantly polished fibers and waveguides coupling as a means for achieving both low optical power reflection and efficient power transmission is proposed. Return losses exceeding -70 dB can be obtained in fiber-to-Lithium Niobate waveguides operating at ) = 0.633 jm and ) = 1.3 pm by polishing the fiber at an angle of 6°. A phase matching condition between the propagation constants ,8 and the polishing angles in the fiber and the waveguide: fl(fiber)sincx(fiber) = fl(waveguide)sina(waveguide) must be fulifiled in order to enable efficient power coupling. Polishing angle tolerances of approximately lO are allowed for a maximum of 1 dB decrease in the coupling efficiency.

Scanning pattern angle effect on the resulting properties of selective laser sintered monolayers of Cu-Sn-Ni powder

NASA Astrophysics Data System (ADS)

Sabelle, Matías; Walczak, Magdalena; Ramos-Grez, Jorge

2018-01-01

Laser-based layer manufacturing of metals, also known as additive manufacturing, is a growing research field of academic and industrial interest. However, in the associated laser-driven processes (i.e. selective laser sintering (SLS) or melting (SLM)), optimization of some parameters has not been fully explored. This research aims at determining how the angle of laser scanning pattern (i.e. build orientation) in SLS affects the mechanical properties and structure of an individual Cu-Sn-Ni alloy metallic layer sintered in the process. Experiments consist in varying the angle of the scanning pattern (0°, 30°, 45° 60° and 90° relative to the transverse dimension of the piece), at constant scanning speed and laser beam power, producing specimens of different thicknesses. A noticeable effect of the scan angle on the mechanical strength and degree of densification of the sintered specimens is found. Thickness of the resulting monolayer correlates negatively with increasing scan angle, whereas relative density correlates positively. A minimum porosity and maximum UTS are found at the angle of 60°. It is concluded that angle of the scanning pattern angle plays a significant role in SLS of metallic monolayers.

Aerodynamic Characteristics of a Flying-Boat Hull Having a Length-Beam Ratio of 15, TED No. NACA 2206

NASA Technical Reports Server (NTRS)

Riebe, John M.; Naeseth, Rodger L.

1951-01-01

An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of a flying-boat hull of a length-beam ratio of 15 in the presence of a wing. The investigation was an extension of previous tests made on hulls of length-beam ratios of 6, 9, and 12; these hulls were designed to have approximately the same hydrodynamic performance with respect to spray and resistance characteristics. Comparison with the previous investigation at lower length-beam ratios indicated a reduction in minimum drag coefficients of 0.0006 (10 peroent)with fixed transition when the length-beam ratio was extended from 12 to 15. As with the hulls of lower length-beam ratio, the drag reduction with a length-beam ratio of 15 occurred throughout the range of angle of attack tested and the angle of attack for minimum drag was in the range from 2deg to 3deg. Increasing the length-beam ratio from 12 to 15 reduced the hull longitudinal instability by an mount corresponding to an aerodynamic-center shift of about 1/2 percent of the mean aerodynamic chord of the hypothetical flying boat. At an angle of attack of 2deg, the value of the variation of yawing-moment coefficient with angle of yaw for a length-beam ratio of 15 was 0.00144, which was 0.00007 larger than the value for a length-beam ratio of 12.

An Empirical Model of Radiation Belt Electron Pitch Angle Distributions Based On Van Allen Probes Measurements

NASA Astrophysics Data System (ADS)

Zhao, H.; Friedel, R. H. W.; Chen, Y.; Reeves, G. D.; Baker, D. N.; Li, X.; Jaynes, A. N.; Kanekal, S. G.; Claudepierre, S. G.; Fennell, J. F.; Blake, J. B.; Spence, H. E.

2018-05-01

Based on over 4 years of Van Allen Probes measurements, an empirical model of radiation belt electron equatorial pitch angle distribution (PAD) is constructed. The model, developed by fitting electron PADs with Legendre polynomials, provides the statistical PADs as a function of L-shell (L = 1-6), magnetic local time, electron energy ( 30 keV to 5.2 MeV), and geomagnetic activity (represented by the Dst index) and is also the first empirical PAD model in the inner belt and slot region. For megaelectron volt electrons, model results show more significant day-night PAD asymmetry of electrons with higher energies and during disturbed times, which is caused by geomagnetic field configuration and flux radial gradient changes. Steeper PADs with higher fluxes around 90° pitch angle and lower fluxes at lower pitch angles for higher-energy electrons and during active times are also present, which could be due to electromagnetic ion cyclotron wave scattering. For hundreds of kiloelectron volt electrons, cap PADs are generally present in the slot region during quiet times and their energy-dependent features are consistent with hiss wave scattering, while during active times, cap PADs are less significant especially at outer part of slot region, which could be due to the complex energizing and transport processes. The 90°-minimum PADs are persistently present in the inner belt and appear in the slot region during active times, and minima at 90° pitch angle are more significant for electrons with higher energies, which could be a critical evidence in identifying the underlying physical processes responsible for the formation of 90°-minimum PADs.

Scleral Buckling Using a Non-contact Wide-Angle Viewing System with a 25-Gauge Chandelier Endoilluminator.

PubMed

Jo, Jaehyuck; Moon, Byung Gil; Lee, Joo Yong

2017-12-01

To report the outcome of scleral buckling using a non-contact wide-angle viewing system with a 25-gauge chandelier endoilluminator. Retrospective analyses of medical records were performed for 17 eyes of 16 patients with primary rhegmatogenous retinal detachment (RRD) without proliferative vitreoretinopathy who had undergone conventional scleral buckling with cryoretinopexy using the combination of a non-contact wide-angle viewing system and chandelier endoillumination. The patients were eight males and five females with a mean age of 26.8 ± 10.2 (range, 11 to 47) years. The mean follow-up period was 7.3 ± 3.1 months. Baseline best-corrected visual acuity was 0.23 ± 0.28 logarithm of the minimum angle of resolution units. Best-corrected visual acuity at the final visit showed improvement (0.20 ± 0.25 logarithm of the minimum angle of resolution units), but the improvement was not statistically significant (p = 0.722). As a surgery-related complication, there was vitreous loss at the end of surgery in one eye. As a postoperative complication, increased intraocular pressure (four cases) and herpes simplex epithelial keratitis (one case) were controlled postoperatively with eye drops. One case of persistent RRD after primary surgery needed additional vitrectomy, and the retina was postoperatively attached. Scleral buckling with chandelier illumination as a surgical technique for RRD has the advantages of relieving the surgeon's neck pain from prolonged use of the indirect ophthalmoscope and sharing the surgical procedure with another surgical team member. In addition, fine retinal breaks that are hard to identify using an indirect ophthalmoscope can be easily found under the microscope by direct endoillumination. © 2017 The Korean Ophthalmological Society

Directed translocation of a flexible polymer through a cone-shaped nano-channel

NASA Astrophysics Data System (ADS)

Nikoofard, Narges; Khalilian, Hamidreza; Fazli, Hossein

2013-08-01

Translocation of a flexible polymer through a cone-shaped channel is studied, theoretically and using computer simulations. Our simulations show that the shape of the channel causes the polymer translocation to be a driven process. The effective driving force of entropic origin acting on the polymer is calculated as a function of the length and the apex-angle of the channel, theoretically. It is found that the translocation time is a non-monotonic function of the apex-angle of the channel. By increasing the apex-angle from zero, the translocation time shows a minimum and then a maximum. Also, it is found that regardless of the value of the apex-angle, the translocation time is a uniformly decreasing function of the channel length. The results of the theory and the simulation are in good qualitative agreement.

16 CFR 1210.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... visual effects, or that depicts (logos, decals, art work, etc.) or resembles in physical form or function... produce a flame; and produces an audible or visual signal that will be clearly discernible when the...

16 CFR 1210.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... visual effects, or that depicts (logos, decals, art work, etc.) or resembles in physical form or function... produce a flame; and produces an audible or visual signal that will be clearly discernible when the...

Assessment of crustal velocity models using seismic refraction and reflection tomography

NASA Astrophysics Data System (ADS)

Zelt, Colin A.; Sain, Kalachand; Naumenko, Julia V.; Sawyer, Dale S.

2003-06-01

Two tomographic methods for assessing velocity models obtained from wide-angle seismic traveltime data are presented through four case studies. The modelling/inversion of wide-angle traveltimes usually involves some aspects that are quite subjective. For example: (1) identifying and including later phases that are often difficult to pick within the seismic coda, (2) assigning specific layers to arrivals, (3) incorporating pre-conceived structure not specifically required by the data and (4) selecting a model parametrization. These steps are applied to maximize model constraint and minimize model non-uniqueness. However, these steps may cause the overall approach to appear ad hoc, and thereby diminish the credibility of the final model. The effect of these subjective choices can largely be addressed by estimating the minimum model structure required by the least subjective portion of the wide-angle data set: the first-arrival times. For data sets with Moho reflections, the tomographic velocity model can be used to invert the PmP times for a minimum-structure Moho. In this way, crustal velocity and Moho models can be obtained that require the least amount of subjective input, and the model structure that is required by the wide-angle data with a high degree of certainty can be differentiated from structure that is merely consistent with the data. The tomographic models are not intended to supersede the preferred models, since the latter model is typically better resolved and more interpretable. This form of tomographic assessment is intended to lend credibility to model features common to the tomographic and preferred models. Four case studies are presented in which a preferred model was derived using one or more of the subjective steps described above. This was followed by conventional first-arrival and reflection traveltime tomography using a finely gridded model parametrization to derive smooth, minimum-structure models. The case studies are from the SE Canadian Cordillera across the Rocky Mountain Trench, central India across the Narmada-Son lineament, the Iberia margin across the Galicia Bank, and the central Chilean margin across the Valparaiso Basin and a subducting seamount. These case studies span the range of modern wide-angle experiments and data sets in terms of shot-receiver spacing, marine and land acquisition, lateral heterogeneity of the study area, and availability of wide-angle reflections and coincident near-vertical reflection data. The results are surprising given the amount of structure in the smooth, tomographically derived models that is consistent with the more subjectively derived models. The results show that exploiting the complementary nature of the subjective and tomographic approaches is an effective strategy for the analysis of wide-angle traveltime data.

Applying six classifiers to airborne hyperspectral imagery for detecting giant reed

USDA-ARS?s Scientific Manuscript database

This study evaluated and compared six different image classifiers, including minimum distance (MD), Mahalanobis distance (MAHD), maximum likelihood (ML), spectral angle mapper (SAM), mixture tuned matched filtering (MTMF) and support vector machine (SVM), for detecting and mapping giant reed (Arundo...

The Mobility Decision. 1990 Wheelchair Guide.

ERIC Educational Resources Information Center

Henke, Cliff

1990-01-01

This article presents tips for parents shopping for wheelchairs for children with special mobility needs. Manual versus power chairs, dimensions, maneuverability, weight, transportability, durability, adaptability, maximum/minimum speeds, battery life (for power chairs), climbing angle, and other features are discussed. Factors to consider in…

16 CFR § 1210.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... visual effects, or that depicts (logos, decals, art work, etc.) or resembles in physical form or function... produce a flame; and produces an audible or visual signal that will be clearly discernible when the...

49 CFR 382.103 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-10-01

... who are required to wear military uniforms), and active duty U.S. Coast Guard personnel; or (3) Who a... governmental functions, are equipped with audible and visual signals, and are not subject to normal traffic...

49 CFR 382.103 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-10-01

... who are required to wear military uniforms), and active duty U.S. Coast Guard personnel; or (3) Who a... governmental functions, are equipped with audible and visual signals, and are not subject to normal traffic...

49 CFR 382.103 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-10-01

... who are required to wear military uniforms), and active duty U.S. Coast Guard personnel; or (3) Who a... governmental functions, are equipped with audible and visual signals, and are not subject to normal traffic...

49 CFR 382.103 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-10-01

... who are required to wear military uniforms), and active duty U.S. Coast Guard personnel; or (3) Who a... governmental functions, are equipped with audible and visual signals, and are not subject to normal traffic...

49 CFR 382.103 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

... who are required to wear military uniforms), and active duty U.S. Coast Guard personnel; or (3) Who a... governmental functions, are equipped with audible and visual signals, and are not subject to normal traffic...

Simulation of Acoustic Noise Generated by an Airbreathing, Beam-Powered Launch Vehicle

NASA Astrophysics Data System (ADS)

Kennedy, W. C.; Van Laak, P.; Scarton, H. A.; Myrabo, L. N.

2005-04-01

A simple acoustic model is developed for predicting the noise signature vs. power level for advanced laser-propelled lightcraft — capable of single-stage flights into low Earth orbit. This model predicts the noise levels generated by a pulsed detonation engine (PDE) during the initial lift-off and acceleration phase, for two representative `tractor-beam' lightcraft designs: a 1-place `Mercury' vehicle (2.5-m diameter, 900-kg); and a larger 5-place `Apollo' vehicle (5-m diameter, 5555-kg) — both the subject of an earlier study. The use of digital techniques to simulate the expected PDE noise signature is discussed, and three examples of fly-by noise signatures are presented. The reduction, or complete elimination of perceptible noise from such engines, can be accomplished by shifting the pulse frequency into the supra-audible or sub-audible range.

Design and analysis of ultrasonic monaural audio guiding device for the visually impaired.

PubMed

Kim, Keonwook; Kim, Hyunjai; Yun, Gihun; Kim, Myungsoo

2009-01-01

The novel Audio Guiding Device (AGD) based on the ultrasonic, which is named as SonicID, has been developed in order to localize point of interest for the visually impaired. The SonicID requires the infrastructure of the transmitters for broadcasting the location information over the ultrasonic carrier. The user with ultrasonic headset receives the information with variable amplitude upon the location and direction of the user due to the ultrasonic characteristic and modulation method. This paper proposes the monaural headset form factor of the SonicID which improves the daily life of the beneficiary compare to the previous version which uses the both ears. Experimental results from SonicID, Bluetooth, and audible sound show that the SonicID demonstrates comparable localization performance to the audible sound with silence to others.

Perception of the Multisensory Coherence of Fluent Audiovisual Speech in Infancy: Its Emergence & the Role of Experience

PubMed Central

Lewkowicz, David J.; Minar, Nicholas J.; Tift, Amy H.; Brandon, Melissa

2014-01-01

To investigate the developmental emergence of the ability to perceive the multisensory coherence of native and non-native audiovisual fluent speech, we tested 4-, 8–10, and 12–14 month-old English-learning infants. Infants first viewed two identical female faces articulating two different monologues in silence and then in the presence of an audible monologue that matched the visible articulations of one of the faces. Neither the 4-month-old nor the 8–10 month-old infants exhibited audio-visual matching in that neither group exhibited greater looking at the matching monologue. In contrast, the 12–14 month-old infants exhibited matching and, consistent with the emergence of perceptual expertise for the native language, they perceived the multisensory coherence of native-language monologues earlier in the test trials than of non-native language monologues. Moreover, the matching of native audible and visible speech streams observed in the 12–14 month olds did not depend on audio-visual synchrony whereas the matching of non-native audible and visible speech streams did depend on synchrony. Overall, the current findings indicate that the perception of the multisensory coherence of fluent audiovisual speech emerges late in infancy, that audio-visual synchrony cues are more important in the perception of the multisensory coherence of non-native than native audiovisual speech, and that the emergence of this skill most likely is affected by perceptual narrowing. PMID:25462038

Perception of the multisensory coherence of fluent audiovisual speech in infancy: its emergence and the role of experience.

PubMed

Lewkowicz, David J; Minar, Nicholas J; Tift, Amy H; Brandon, Melissa

2015-02-01

To investigate the developmental emergence of the perception of the multisensory coherence of native and non-native audiovisual fluent speech, we tested 4-, 8- to 10-, and 12- to 14-month-old English-learning infants. Infants first viewed two identical female faces articulating two different monologues in silence and then in the presence of an audible monologue that matched the visible articulations of one of the faces. Neither the 4-month-old nor 8- to 10-month-old infants exhibited audiovisual matching in that they did not look longer at the matching monologue. In contrast, the 12- to 14-month-old infants exhibited matching and, consistent with the emergence of perceptual expertise for the native language, perceived the multisensory coherence of native-language monologues earlier in the test trials than that of non-native language monologues. Moreover, the matching of native audible and visible speech streams observed in the 12- to 14-month-olds did not depend on audiovisual synchrony, whereas the matching of non-native audible and visible speech streams did depend on synchrony. Overall, the current findings indicate that the perception of the multisensory coherence of fluent audiovisual speech emerges late in infancy, that audiovisual synchrony cues are more important in the perception of the multisensory coherence of non-native speech than that of native audiovisual speech, and that the emergence of this skill most likely is affected by perceptual narrowing. Copyright © 2014 Elsevier Inc. All rights reserved.

Study of motion of optimal bodies in the soil of grid method

NASA Astrophysics Data System (ADS)

Kotov, V. L.; Linnik, E. Yu

2016-11-01

The paper presents a method of calculating the optimum forms in axisymmetric numerical method based on the Godunov and models elastoplastic soil vedium Grigoryan. Solved two problems in a certain definition of generetrix rotation of the body of a given length and radius of the base, having a minimum impedance and maximum penetration depth. Numerical calculations are carried out by a modified method of local variations, which allows to significantly reduce the number of operations at different representations of generetrix. Significantly simplify the process of searching for optimal body allows the use of a quadratic model of local interaction for preliminary assessments. It is noted the qualitative similarity of the process of convergence of numerical calculations for solving the optimization problem based on local interaction model and within the of continuum mechanics. A comparison of the optimal bodies with absolutely optimal bodies possessing the minimum resistance of penetration below which is impossible to achieve under given constraints on the geometry. It is shown that the conical striker with a variable vertex angle, which equal to the angle of the solution is absolutely optimal body of minimum resistance of penetration for each value of the velocity of implementation will have a final depth of penetration is only 12% more than the traditional body absolutely optimal maximum depth penetration.

Temporal change in the electromechanical properties of dielectric elastomer minimum energy structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchberger, G., E-mail: erda.buchberger@jku.at; Hauser, B.; Jakoby, B.

Dielectric elastomer minimum energy structures (DEMES) are soft electronic transducers and energy harvesters with potential for consumer goods. The temporal change in their electromechanical properties is of major importance for engineering tasks. Therefore, we study acrylic DEMES by impedance spectroscopy and by optical methods for a total time period of approx. 4.5 months. We apply either compliant electrodes from carbon black particles only or fluid electrodes from a mixture of carbon black particles and silicone oil. From the measurement data, the equivalent series capacitances and resistances as well as the bending angles of the transducers are obtained. We find thatmore » the equivalent series capacitances change in average between −12 %/1000 h and −4.0 %/1000 h, while the bending angles decrease linearly with slopes ranging from −15 %/1000 h to −7 %/1000 h. Transducers with high initial bending angles and electrodes from carbon black particles show the smallest changes of the electromechanical characteristics. The capacitances decrease faster for DEMES with fluid electrodes. Some DEMES of this type reveal huge and unpredictable fluctuations of the resistances over time due to the ageing of the contacts. Design guidelines for DEMES follow directly from the observed transient changes of their electromechanical performance.« less

Quality assessment of two- and three-dimensional unstructured meshes and validation of an upwind Euler flow solver

NASA Technical Reports Server (NTRS)

Woodard, Paul R.; Batina, John T.; Yang, Henry T. Y.

1992-01-01

Quality assessment procedures are described for two-dimensional unstructured meshes. The procedures include measurement of minimum angles, element aspect ratios, stretching, and element skewness. Meshes about the ONERA M6 wing and the Boeing 747 transport configuration are generated using an advancing front method grid generation package of programs. Solutions of Euler's equations for these meshes are obtained at low angle-of-attack, transonic conditions. Results for these cases, obtained as part of a validation study demonstrate accuracy of an implicit upwind Euler solution algorithm.

Solid state laser

NASA Technical Reports Server (NTRS)

Rines, Glen A. (Inventor); Moulton, Peter F. (Inventor); Harrison, James (Inventor)

1993-01-01

A wavelength-tunable, injection-seeded, dispersion-compensated, dispersively-pumped solid state laser includes a lasing medium; a highly reflective mirror; an output coupler; at least one isosceles Brewster prism oriented to the minimum deviation angle between the medium and the mirror for directing light of different wavelengths along different paths; means for varying the angle of the highly reflective mirror relative to the light from at least one Brewster angle for selecting a predetermined laser operating wavelength; a dispersion compensation apparatus associated with the lasing medium; a laser injection seeding port disposed between the dispersion compensation apparatus and one of the mirror and coupler and including a reflective surface at an acute non-Brewster angle to the laser beam for introducing a seed input; a dispersion compensation apparatus associated with the laser medium including opposite chirality optical elements; the lasing medium including a pump surface disposed at an acute angle to the laser beam to define a discrete path for the pumping laser beam separate from the pumped laser beam.

Parametric Investigation on the Use of Lateral and Logitudinal Rotor Trim Flapping for Tiltrotor Noise Reduction

NASA Technical Reports Server (NTRS)

Malpica, Carlos

2017-01-01

This paper presents an acoustics parametric study of the effect of varying lateral and longitudinal rotor trim flapping angles (tip-path-plane tilt) on noise radiated by an isolated 26-ft diameter proprotor, similar to that of the AW609 tiltrotor, in edgewise flight. Three tip-path-plane angle of attack operating conditions of -9, 0 and 6 deg, at 80 knots, were investigated. Results showed that: 1) minimum noise was attained for the tip-path-plane angle of attack value of -9 deg, and 2) changing the cyclic trim state (i.e., controls) altered the airloads and produced noticeable changes to the low-frequency (LF) and blade-vortex interaction (BVI) radiated-noise magnitude and directionality. In particular, by trimming the rotor to a positive (inboard) lateral flapping angle of 4 deg, further reductions up to 3 dB in the low-frequency noise sound pressure level were attained without significantly impacting the BVI noise for longitudinal tip-path-plane angles of -9 and 6 deg.

Hurricane Irene

Atmospheric Science Data Center

2013-04-19

... scale, with maximum sustained winds of 115 mph (185 kph), and a minimum central pressure of 951 hPa, according to NOAA's National ... an angle of 46 degrees. The storm is visible to the north of Cuba, which is located in the lower left of the image. Irene's eye is covered ...

High mobility work station restraint support

NASA Technical Reports Server (NTRS)

Schermerhorn, R. S.

1971-01-01

Chair holds man in semistanding posture enabling astronauts to work comfortably with minimum restriction in weightless environment. Seat, angled at 130 deg to back support, twists and swivels up to 20 deg in all directions but forward. Two flexible thigh clips prevent occupant from slipping off.

Incident flux angle induced crystal texture transformation in nanostructured molybdenum films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, L.; Lu, T.-M.; Wang, G.-C.

2012-07-15

Molybdenum films were observed to undergo a dramatic change in crystal texture orientation when the incident flux angle was varied in an oblique angle sputter deposition on amorphous substrates. Reflection high-energy electron diffraction pole figure and scanning electron microscopy were used to analyze in detail the texture orientation of the films. The normal incident deposition resulted in a fiber texture film with the minimum energy (110) crystal plane parallel to the substrate surface. A (110)[110] biaxial texture was observed for the samples grown with low incident angles of less than 45 Degree-Sign , with respect to the surface normal. Onmore » the other hand, for an oblique angle deposition of larger than 60 Degree-Sign , a (111)[112] biaxial texture was observed and appeared to be consistent with a zone T structure where the geometrically fastest growth [001] direction of a crystal plays a dominant role in defining the texture. We argue that a structural transition had occurred when the incident flux was varied from near normal incidence to a large angle.« less

SCD 02 thermal design

NASA Technical Reports Server (NTRS)

Cardoso, Humberto Pontes

1990-01-01

The Satelite de Coleta de Dados (SCD) 02 (Data Collection Satellite) has the following characteristics: 115 kg weight, octagonal prism shape, 1 m diameter, and 0.67 m height. Its specified orbit is nearly circular, 700 km altitude, is inclined 25 deg with respect to the equator line, and has 100 min period. The electric power is supplied by eight solar panels installed on the lateral sides of the satellite. The equipment is located on the central (both faces) and lower (internal face) panels. The satellite is spin stabilized and its attitude control is such that during its lifetime, the solar aspect angle will vary between 80 and 100 deg with respect to its spin axis. Two critical cases were selected for thermal control design purposes: Hot case (maximum solar constant, solar aspect angle equal to 100 deg, minimum eclipse time and maximum internal heat dissipation); and a passive thermal design concept was achieved and the maximum and minimum equipment operating temperatures were obtained through a 109 node finite difference mathematical model.

Research on the system performance evaluation of minimum-shift keying in uplink ground-to-satellite with gamma-gamma distribution

NASA Astrophysics Data System (ADS)

Wang, Yi; Zhang, Ao; Ma, Jing

2017-07-01

Minimum-shift keying (MSK) has the advantages of constant envelope, continuous phase, and high spectral efficiency, and it is applied in radio communication and optical fiber communication. MSK modulation of coherent detection is proposed in the ground-to-satellite laser communication system; in addition, considering the inherent noise of uplink, such as intensity scintillation and beam wander, the communication performance of the MSK modulation system with coherent detection is studied in the uplink ground-to-satellite laser. Based on the gamma-gamma channel model, the closed form of bit error rate (BER) of MSK modulation with coherent detection is derived. In weak, medium, and strong turbulence, the BER performance of the MSK modulation system is simulated and analyzed. To meet the requirements of the ground-to-satellite coherent MSK system to optimize the parameters and configuration of the transmitter and receiver, the influence of the beam divergence angle, the zenith angle, the transmitter beam radius, and the receiver diameter are studied.

Geometrically distributed one-dimensional photonic crystals for light-reflection in all angles.

PubMed

Alagappan, G; Wu, P

2009-07-06

We demonstrate that a series of one-dimensional photonic crystals made of any dielectric materials, with the periods are distributed in a geometrical progression of a common ratio, r < rc (theta,P), where rc is a structural parameter that depends on the angle of incidence, theta, and polarization, P, is capable of blocking light of any spectral range. If an omni-directional reflection is desired for all polarizations and for all incident angles smaller than thetao, then r < rc (theta(o),p), where p is the polarization with the electric field parallel to the plane of incidence. We present simple and formula like expressions for rc, width of the bandgap, and minimum number of photonic crystals to achieve a perfect light reflection.

Simplified planar model of a car steering system with rack and pinion and McPherson suspension

NASA Astrophysics Data System (ADS)

Knapczyk, J.; Kucybała, P.

2016-09-01

The paper presents the analysis and optimization of steering system with rack and pinion and McPherson suspension using spatial model and equivalent simplified planar model. The dimension of the steering linkage that give minimum steering error can be estimated using planar model. The steering error is defined as the difference between the actual angle made by the outer front wheel during steering manoeuvers and the calculated angle for the same wheel based on the Ackerman principle. For a given linear rack displacement, a specified steering arms angular displacements are determined while simultaneously ensuring best transmission angle characteristics (i) without and (ii) with imposing linear correlation between input and output. Numerical examples are used to illustrate the proposed method.

21 CFR 870.1025 - Arrhythmia detector and alarm (including ST-segment measurement and alarm).

Code of Federal Regulations, 2011 CFR

2011-04-01

... a visible or audible signal or alarm when atrial or ventricular arrhythmia, such as premature contraction or ventricular fibrillation, occurs. (b) Classification. Class II (special controls). The guidance...

21 CFR 870.1025 - Arrhythmia detector and alarm (including ST-segment measurement and alarm).

Code of Federal Regulations, 2010 CFR

2010-04-01

... a visible or audible signal or alarm when atrial or ventricular arrhythmia, such as premature contraction or ventricular fibrillation, occurs. (b) Classification. Class II (special controls). The guidance...

46 CFR 160.151-57 - Servicing procedure.

Code of Federal Regulations, 2011 CFR

2011-10-01

... its weight loss exceeds five percent of the weight of the charge, it must be recharged. (c) When an... in the buoyancy tubes is audible, accompanied by pressure loss, condemn the liferaft. If it is not...

Thermodynamics of Surface Nanobubbles.

PubMed

Zargarzadeh, Leila; Elliott, Janet A W

2016-11-01

In this paper, we examine the thermodynamic stability of surface nanobubbles. The appropriate free energy is defined for the system of nanobubbles on a solid surface submerged in a supersaturated liquid solution at constant pressure and temperature, under conditions where an individual nanobubble is not in diffusive contact with a gas phase outside of the system or with other nanobubbles on the time scale of the experiment. The conditions under which plots of free energy versus the radius of curvature of the nanobubbles show a global minimum, which denotes the stable equilibrium state, are explored. Our investigation shows that supersaturation and an anomalously high contact angle (measured through the liquid) are required to have stable surface nanobubbles. In addition, the anomalously high contact angle of surface nanobubbles is discussed from the standpoint of a framework recently proposed by Koch, Amirfazli, and Elliott that relates advancing and receding contact angles to thermodynamic equilibrium contact angles, combined with the existence of a gas enrichment layer.

Optimal Electrodynamic Tether Phasing Maneuvers

NASA Technical Reports Server (NTRS)

Bitzer, Matthew S.; Hall, Christopher D.

2007-01-01

We study the minimum-time orbit phasing maneuver problem for a constant-current electrodynamic tether (EDT). The EDT is assumed to be a point mass and the electromagnetic forces acting on the tether are always perpendicular to the local magnetic field. After deriving and non-dimensionalizing the equations of motion, the only input parameters become current and the phase angle. Solution examples, including initial Lagrange costates, time of flight, thrust plots, and thrust angle profiles, are given for a wide range of current magnitudes and phase angles. The two-dimensional cases presented use a non-tilted magnetic dipole model, and the solutions are compared to existing literature. We are able to compare similar trajectories for a constant thrust phasing maneuver and we find that the time of flight is longer for the constant thrust case with similar initial thrust values and phase angles. Full three-dimensional solutions, which use a titled magnetic dipole model, are also analyzed for orbits with small inclinations.

Correlation Between Geometric Similarity of Ice Shapes and the Resulting Aerodynamic Performance Degradation: A Preliminary Investigation Using WIND

NASA Technical Reports Server (NTRS)

Wright, William B.; Chung, James

1999-01-01

Aerodynamic performance calculations were performed using WIND on ten experimental ice shapes and the corresponding ten ice shapes predicted by LEWICE 2.0. The resulting data for lift coefficient and drag coefficient are presented. The difference in aerodynamic results between the experimental ice shapes and the LEWICE ice shapes were compared to the quantitative difference in ice shape geometry presented in an earlier report. Correlations were generated to determine the geometric features which have the most effect on performance degradation. Results show that maximum lift and stall angle can be correlated to the upper horn angle and the leading edge minimum thickness. Drag coefficient can be correlated to the upper horn angle and the frequency-weighted average of the Fourier coefficients. Pitching moment correlated with the upper horn angle and to a much lesser extent to the upper and lower horn thicknesses.

Computational Study of Fluidic Thrust Vectoring using Separation Control in a Nozzle

NASA Technical Reports Server (NTRS)

Deere, Karen; Berrier, Bobby L.; Flamm, Jeffrey D.; Johnson, Stuart K.

2003-01-01

A computational investigation of a two- dimensional nozzle was completed to assess the use of fluidic injection to manipulate flow separation and cause thrust vectoring of the primary jet thrust. The nozzle was designed with a recessed cavity to enhance the throat shifting method of fluidic thrust vectoring. The structured-grid, computational fluid dynamics code PAB3D was used to guide the design and analyze over 60 configurations. Nozzle design variables included cavity convergence angle, cavity length, fluidic injection angle, upstream minimum height, aft deck angle, and aft deck shape. All simulations were computed with a static freestream Mach number of 0.05. a nozzle pressure ratio of 3.858, and a fluidic injection flow rate equal to 6 percent of the primary flow rate. Results indicate that the recessed cavity enhances the throat shifting method of fluidic thrust vectoring and allows for greater thrust-vector angles without compromising thrust efficiency.

A unified viscous theory of lift and drag of 2-D thin airfoils and 3-D thin wings

NASA Technical Reports Server (NTRS)

Yates, John E.

1991-01-01

A unified viscous theory of 2-D thin airfoils and 3-D thin wings is developed with numerical examples. The viscous theory of the load distribution is unique and tends to the classical inviscid result with Kutta condition in the high Reynolds number limit. A new theory of 2-D section induced drag is introduced with specific applications to three cases of interest: (1) constant angle of attack; (2) parabolic camber; and (3) a flapped airfoil. The first case is also extended to a profiled leading edge foil. The well-known drag due to absence of leading edge suction is derived from the viscous theory. It is independent of Reynolds number for zero thickness and varies inversely with the square root of the Reynolds number based on the leading edge radius for profiled sections. The role of turbulence in the section induced drag problem is discussed. A theory of minimum section induced drag is derived and applied. For low Reynolds number the minimum drag load tends to the constant angle of attack solution and for high Reynolds number to an approximation of the parabolic camber solution. The parabolic camber section induced drag is about 4 percent greater than the ideal minimum at high Reynolds number. Two new concepts, the viscous induced drag angle and the viscous induced separation potential are introduced. The separation potential is calculated for three 2-D cases and for a 3-D rectangular wing. The potential is calculated with input from a standard doublet lattice wing code without recourse to any boundary layer calculations. Separation is indicated in regions where it is observed experimentally. The classical induced drag is recovered in the 3-D high Reynolds number limit with an additional contribution that is Reynold number dependent. The 3-D viscous theory of minimum induced drag yields an equation for the optimal spanwise and chordwise load distribution. The design of optimal wing tip planforms and camber distributions is possible with the viscous 3-D wing theory.

Speech Recognition and Parent Ratings From Auditory Development Questionnaires in Children Who Are Hard of Hearing.

PubMed

McCreery, Ryan W; Walker, Elizabeth A; Spratford, Meredith; Oleson, Jacob; Bentler, Ruth; Holte, Lenore; Roush, Patricia

2015-01-01

Progress has been made in recent years in the provision of amplification and early intervention for children who are hard of hearing. However, children who use hearing aids (HAs) may have inconsistent access to their auditory environment due to limitations in speech audibility through their HAs or limited HA use. The effects of variability in children's auditory experience on parent-reported auditory skills questionnaires and on speech recognition in quiet and in noise were examined for a large group of children who were followed as part of the Outcomes of Children with Hearing Loss study. Parent ratings on auditory development questionnaires and children's speech recognition were assessed for 306 children who are hard of hearing. Children ranged in age from 12 months to 9 years. Three questionnaires involving parent ratings of auditory skill development and behavior were used, including the LittlEARS Auditory Questionnaire, Parents Evaluation of Oral/Aural Performance in Children rating scale, and an adaptation of the Speech, Spatial, and Qualities of Hearing scale. Speech recognition in quiet was assessed using the Open- and Closed-Set Test, Early Speech Perception test, Lexical Neighborhood Test, and Phonetically Balanced Kindergarten word lists. Speech recognition in noise was assessed using the Computer-Assisted Speech Perception Assessment. Children who are hard of hearing were compared with peers with normal hearing matched for age, maternal educational level, and nonverbal intelligence. The effects of aided audibility, HA use, and language ability on parent responses to auditory development questionnaires and on children's speech recognition were also examined. Children who are hard of hearing had poorer performance than peers with normal hearing on parent ratings of auditory skills and had poorer speech recognition. Significant individual variability among children who are hard of hearing was observed. Children with greater aided audibility through their HAs, more hours of HA use, and better language abilities generally had higher parent ratings of auditory skills and better speech-recognition abilities in quiet and in noise than peers with less audibility, more limited HA use, or poorer language abilities. In addition to the auditory and language factors that were predictive for speech recognition in quiet, phonological working memory was also a positive predictor for word recognition abilities in noise. Children who are hard of hearing continue to experience delays in auditory skill development and speech-recognition abilities compared with peers with normal hearing. However, significant improvements in these domains have occurred in comparison to similar data reported before the adoption of universal newborn hearing screening and early intervention programs for children who are hard of hearing. Increasing the audibility of speech has a direct positive effect on auditory skill development and speech-recognition abilities and also may enhance these skills by improving language abilities in children who are hard of hearing. Greater number of hours of HA use also had a significant positive impact on parent ratings of auditory skills and children's speech recognition.

Simulator study of the effectiveness of an automatic control system designed to improve the high-angle-of-attack characteristics of a fighter airplane

NASA Technical Reports Server (NTRS)

Gilbert, W. P.; Nguyen, L. T.; Vangunst, R. W.

1976-01-01

A piloted, fixed-base simulation was conducted to study the effectiveness of some automatic control system features designed to improve the stability and control characteristics of fighter airplanes at high angles of attack. These features include an angle-of-attack limiter, a normal-acceleration limiter, an aileron-rudder interconnect, and a stability-axis yaw damper. The study was based on a current lightweight fighter prototype. The aerodynamic data used in the simulation were measured on a 0.15-scale model at low Reynolds number and low subsonic Mach number. The simulation was conducted on the Langley differential maneuvering simulator, and the evaluation involved representative combat maneuvering. Results of the investigation show the fully augmented airplane to be quite stable and maneuverable throughout the operational angle-of-attack range. The angle-of-attack/normal-acceleration limiting feature of the pitch control system is found to be a necessity to avoid angle-of-attack excursions at high angles of attack. The aileron-rudder interconnect system is shown to be very effective in making the airplane departure resistant while the stability-axis yaw damper provided improved high-angle-of-attack roll performance with a minimum of sideslip excursions.

Visual field structure in the Empress Leilia, Asterocampa leilia (Lepidoptera, Nymphalidae): dimensions and regional variation in acuity.

PubMed

Rutowski, Ronald L; Warrant, Eric J

2002-02-01

Male Empress Leilia butterflies ( Asterocampa leilia) use a sit-and-wait tactic to locate mates. To see how vision might influence male behavior, we studied the morphology, optics, and receptor physiology of their eyes and found the following. (1) Each eye's visual field is approximately hemispherical with at most a 10 degrees overlap in the fields of the eyes. There are no large sexual differences in visual field dimensions. (2) In both sexes, rhabdoms in the frontal and dorsal ommatidia are longer than those in other eye regions. (3) Interommatidial angles are smallest frontally and around the equator of the eye. Minimum interommatidial angles are 0.9-1 degrees in males and 1.3-1.4 degrees in females. (4) Acceptance angles of ommatidia closely match interommatidial angles in the frontal region of the eye. We conclude that vision in these butterflies is mostly monocular and that males have more acute vision than females, especially in the frontal region (large facets, small interommatidial angles, small acceptance angles, long rhabdoms, and a close match between interommatidial angles and acceptance angles). This study also suggests that perched males direct their most acute vision where females are likely to appear but show no eye modifications that appear clearly related to a mate-locating tactic.

Growth and analysis of gallium arsenide-gallium antimonide single and two-phase nanoparticles

NASA Astrophysics Data System (ADS)

Schamp, Crispin T.

When evaluating the path of phase transformations in systems with nanoscopic dimensions one often relies on bulk phase diagrams for guidance because of the lack of phase diagrams that show the effect of particle size. The GaAs-GaSb pseudo-binary alloy is chosen for study to gain insight into the size dependence of solid-solubility in a two-phase system. To this end, a study is performed using independent laser ablation of high purity targets of GaAs and GaSb. The resultant samples are analyzed by transmission electron microscopy. Experimental results indicate that GaAs-GaSb nanoparticles have been formed with compositions that lie within the miscibility gap of bulk GaAs-GaSb. An unusual nanoparticle morpohology resembling the appearance of ice cream cones has been observed in single component experiments. These particles are composed of a spherical cap of Ga in contact with a crystalline cone of either GaAs or GaSb. The cones take the projected 2-D shape of a triangle or a faceted gem. The liquid Ga is found to consistently be of spherical shape and wets to the widest corners of the cone, suggesting an energy minimum exists at that wetting condition. To explore this observation a liquid sphere is modeled as being penetrated by a solid gem. The surface energies of the solid and liquid, and interfacial energy are summed as a function of penetration depth, with the sum showing a cusped minimum at the penetration depth corresponding to the waist of the gem. The angle of contact of the liquid wetting the cone is also calculated, and Young's contact angle is found to occur when the derivative of the total energy with respect to penetration depth is zero, which can be a maximum or a minimum depending on the geometrical details. The spill-over of the meniscus across the gem corners is found to be energetically favorable when the contact angle achieves the value of the equilibrium angle; otherwise the meniscus is pinned at the corners.

Initial utility experience with cluster of three Mod-2 wind turbine systems

NASA Technical Reports Server (NTRS)

Seely, D. B.; Warchol, E. J.; Butler, N. G.; Ciranny, S.

1982-01-01

This paper describes the initial utility experiences of operating three MOD-2s during the Engineering Acceptance Testing. Electrical quantities of bus voltage, phase currents and power are initially being recorded to evaluate impacts to customers on the 69-kV subtransmission line during synchronization and operation of one or more WTSs. To date, effects on the system have been essentially undetectable. Measurements of television signal strengths were taken at an existing television remote pickup and relay station at the WTS site. Potential TV signal interference problems from the WTSs have been avoided by replacing the remote pickups with microwave repeater links for the four TV channels received from Portland, Oregon. Preliminary measurements of audible and sub-audible noise levels indicate that the upwind rotor, tubular tower design of the MOD-2 does not have the pulsing high intensity infrasound problems experienced by the MOD-1 machine at Boone, North Carolina.

Metronome rate and walking foot contact time in young adults.

PubMed

Dickstein, Ruth; Plax, Michael

2012-02-01

It is assumed that when people walk guided by an audible constant rate, they match foot contact to the external pace. The purpose of this preliminary study was to test that assumption by examining the temporal relationship between audible signals generated by a metronome and foot contact time during gait. Ten healthy young women were tested in walking repetitions guided by metronome rates of 60, 110, and 150 beats/min. Metronome beats and foot contact times were collected in real time. The findings indicated that foot contact was not fully synchronized with the auditory signals; the shortest time interval between the metronome beat and foot contact time was at the prescribed rate of 60 beats/min., while the longest interval was at the rate of 150 beats/min. The correlation between left and right foot contact times was highest with the slowest rate and lowest with the fastest rate.

Neurophysiological evidence of efference copies to inner speech

PubMed Central

Jack, Bradley N; Pearson, Daniel; Griffiths, Oren; Luque, David; Harris, Anthony WF; Spencer, Kevin M; Le Pelley, Mike E

2017-01-01

Efference copies refer to internal duplicates of movement-producing neural signals. Their primary function is to predict, and often suppress, the sensory consequences of willed movements. Efference copies have been almost exclusively investigated in the context of overt movements. The current electrophysiological study employed a novel design to show that inner speech – the silent production of words in one’s mind – is also associated with an efference copy. Participants produced an inner phoneme at a precisely specified time, at which an audible phoneme was concurrently presented. The production of the inner phoneme resulted in electrophysiological suppression, but only if the content of the inner phoneme matched the content of the audible phoneme. These results demonstrate that inner speech – a purely mental action – is associated with an efference copy with detailed auditory properties. These findings suggest that inner speech may ultimately reflect a special type of overt speech. PMID:29199947

Hush House-induced vibrations at the Arkansas Air National Guard Facility, Fort Smith, Arkansas. Environmental research papers, 1 October 1986-30 September 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Battis, J.C.

1987-11-13

The T-10 jet engine ground run-up noise suppressor, or Hush House, was designed to reduce the audible effects of jet engine testing on the surrounding community. At least in part, the noise-suppression characteristics of the Hush House are achieved by the transfer of energy from the audible (> 20 Hz) to the infrasonic range (<20 Hz). At some sites these lower-frequency emissions have had deleterious effects on the vibro-acoustic environment of nearby buildings. This report describes a case study on this problem and demonstrates that existing siting criteria for the Hush House are inadequate; in one case being too stringentmore » and in another case too lax. An acoustic-emissions model for the Hush House is proposed based on multiple jet-type sources.« less

Emergency Vehicle Siren Noise Effectiveness

NASA Astrophysics Data System (ADS)

D'Angela, Peter

Navigating safely through traffic, while responding to an emergency, is often a challenge for emergency responders. To help alert other motorists, these responders use emergency lights and/or sirens. However, the former is useful only if within clear visual range of the other drivers. This shortcoming puts a greater emphasis on the importance of the audible emergency siren, which has its own shortcomings. This study considered several emergency siren systems with the goal to determine the most effective siren system(s) based on several criteria. Multiple experimental measurements and subjective analysis using jury testing using an NVH driving simulator were performed. It was found that the traditional mechanical siren was the most effective audible warning device; however, with significantly reduced electrical power requirements, the low frequency Rumbler siren, in conjunction with a more conventional electronic Yelp siren, was the preferred option. Recommendations for future work are also given.

Investigating the Feedback Path in a Jet-Surface Resonant Interaction

NASA Technical Reports Server (NTRS)

Zaman, Khairul; Fagan, Amy; Bridges, James; Brown, Cliff

2015-01-01

A resonant interaction between an 8:1 aspect ratio rectangular jet and flat-plates, placed parallel to the jet, is addressed in this study. For certain relative locations of the plates, the resonance takes place with accompanying audible tones. Even when the tone is not audible the sound pressure level spectra is often marked by conspicuous peaks. The frequencies of the spectral peaks, as functions of the streamwise length of the plate and its relative location to the jet as well as the jet Mach number, are explored in an effort of understand the flow mechanism. It is demonstrated that the tones are not due to a simple feedback between the plates trailing edge and the nozzle exit; the leading edge also comes into play in determining the frequency. An acoustic feedback path, involving diffraction from the leading edge, appears to explain the frequencies of some of the spectral peaks.

Theoretical studies on leaky-SAW properties influenced by layers on anisotropic piezoelectric crystals.

PubMed

Wallner, P; Ruile, W; Weigel, R

2000-01-01

Theoretical studies on the behavior of leaky-SAW (LSAW) properties in layered structures were performed. For these calculations rotYX LiTaO (3) and rotYX LiNbO(3) LSAW crystal cuts were used, assuming different layer materials. For LSAWs both the velocity and the inherent loss due to bulk wave emission into the substrate are strongly influenced by distinct layer parameters. As a result, these layer properties like elastic constants or thickness have shown a strong influence on the crystal cut angle of minimum LSAW loss. Moreover, for soft and stiff layer materials, a different shift of the LSAW loss minimum can occur. Therefore, using double-layer structures, the shift of the LSAW loss minimum can be influenced by appropriate chosen layers and ratios.

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to a line from stem to blossom end. When measuring for maximum size, “diameter” means the smallest dimension of the apple determined by...

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to a line from stem to blossom end. When measuring for maximum size, “diameter” means the smallest dimension of the apple determined by...

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., CERTIFICATION, AND STANDARDS) United States Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to... dimension of the apple determined by passing the apple through a round opening in any position. U.S...

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., CERTIFICATION, AND STANDARDS) United States Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to... dimension of the apple determined by passing the apple through a round opening in any position. U.S...

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to a line from stem to blossom end. When measuring for maximum size, “diameter” means the smallest dimension of the apple determined by...

46 CFR 177.900 - Deck rails.

Code of Federal Regulations, 2010 CFR

2010-10-01

... rails must be designed and constructed to withstand a point load of 91 kilograms (200 pounds) applied at... simultaneously. (c) Where space limitations make deck rails impractical for areas designed for crew use only...) high. (4) While engaged in big game angling, the minimum rail height may be reduced to not less than...

46 CFR 177.900 - Deck rails.

Code of Federal Regulations, 2012 CFR

2012-10-01

... rails must be designed and constructed to withstand a point load of 91 kilograms (200 pounds) applied at... simultaneously. (c) Where space limitations make deck rails impractical for areas designed for crew use only...) high. (4) While engaged in big game angling, the minimum rail height may be reduced to not less than...

46 CFR 177.900 - Deck rails.

Code of Federal Regulations, 2014 CFR

2014-10-01

... rails must be designed and constructed to withstand a point load of 91 kilograms (200 pounds) applied at... simultaneously. (c) Where space limitations make deck rails impractical for areas designed for crew use only...) high. (4) While engaged in big game angling, the minimum rail height may be reduced to not less than...

46 CFR 177.900 - Deck rails.

Code of Federal Regulations, 2011 CFR

2011-10-01

... rails must be designed and constructed to withstand a point load of 91 kilograms (200 pounds) applied at... simultaneously. (c) Where space limitations make deck rails impractical for areas designed for crew use only...) high. (4) While engaged in big game angling, the minimum rail height may be reduced to not less than...

46 CFR 177.900 - Deck rails.

Code of Federal Regulations, 2013 CFR

2013-10-01

... rails must be designed and constructed to withstand a point load of 91 kilograms (200 pounds) applied at... simultaneously. (c) Where space limitations make deck rails impractical for areas designed for crew use only...) high. (4) While engaged in big game angling, the minimum rail height may be reduced to not less than...

7 CFR 51.1859 - Size.

Code of Federal Regulations, 2011 CFR

2011-01-01

... cherry tomatoes and Pyriforme type tomatoes commonly referred to as pear shaped tomatoes, and other... Standards for Fresh Tomatoes 1 Size § 51.1859 Size. (a) The size of tomatoes packed in any standard type... measurement for minimum diameter shall be the largest diameter of the tomato measured at right angles to a...

7 CFR 51.1859 - Size.

Code of Federal Regulations, 2010 CFR

2010-01-01

... cherry tomatoes and Pyriforme type tomatoes commonly referred to as pear shaped tomatoes, and other... Standards for Fresh Tomatoes 1 Size § 51.1859 Size. (a) The size of tomatoes packed in any standard type... measurement for minimum diameter shall be the largest diameter of the tomato measured at right angles to a...

The Recognizability and Localizability of Auditory Alarms: Setting Global Medical Device Standards.

PubMed

Edworthy, Judy; Reid, Scott; McDougall, Siné; Edworthy, Jonathan; Hall, Stephanie; Bennett, Danielle; Khan, James; Pye, Ellen

2017-11-01

Objective Four sets of eight audible alarms matching the functions specified in IEC 60601-1-8 were designed using known principles from auditory cognition with the intention that they would be more recognizable and localizable than those currently specified in the standard. Background The audible alarms associated with IEC 60601-1-8, a global medical device standard, are known to be difficult to learn and retain, and there have been many calls to update them. There are known principles of design and cognition that might form the basis of more readily recognizable alarms. There is also scope for improvement in the localizability of the existing alarms. Method Four alternative sets of alarms matched to the functions specified in IEC 60601-1-8 were tested for recognizability and localizability and compared with the alarms currently specified in the standard. Results With a single exception, all prototype sets of alarms outperformed the current IEC set on both recognizability and localizability. Within the prototype sets, auditory icons were the most easily recognized, but the other sets, using word rhythms and simple acoustic metaphors, were also more easily recognized than the current alarms. With the exception of one set, all prototype sets were also easier to localize. Conclusion Known auditory cognition and perception principles were successfully applied to an existing audible alarm problem. Application This work constitutes the first (benchmarking) phase of replacing the alarms currently specified in the standard. The design principles used for each set demonstrate the relative ease with which different alarm types can be recognized and localized.

Scanning mirror for infrared sensors

NASA Technical Reports Server (NTRS)

Anderson, R. H.; Bernstein, S. B.

1972-01-01

A high resolution, long life angle-encoded scanning mirror, built for application in an infrared attitude sensor, is described. The mirror uses a Moire' fringe type optical encoder and unique torsion bar suspension together with a magnetic drive to meet stringent operational and environmental requirements at a minimum weight and with minimum power consumption. Details of the specifications, design, and construction are presented with an analysis of the mirror suspension that allows accurate prediction of performance. The emphasis is on mechanical design considerations, and brief discussions are included on the encoder and magnetic drive to provide a complete view of the mirror system and its capabilities.

Rovers Eye View of 3 Year Trek on Mars

NASA Image and Video Library

2010-06-11

309 images of the Martian horizon taken during 13-mile journey from Victoria crater to Endeavour crater. Numbers at top left are Martian day numbers (sols). Audio comes from rover accelerometer data adjusted to an audible frequency.

Evaluation of the effectiveness of centerline rumble stripes on rural roads.

DOT National Transportation Integrated Search

2015-03-01

This report documents the site characteristics, constructability, summary of audibility testing, and maintenance response of centerline rumble : stripes at two locations: US Route 4 in Mendon-Killington and VT Route 105 in Sheldon. : The primary obje...

49 CFR 393.75 - Tires.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Has body ply or belt material exposed through the tread or sidewall, (2) Has any tread or sidewall separation, (3) Is flat or has an audible leak, or (4) Has a cut to the extent that the ply or belt material...

49 CFR 393.75 - Tires.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Has body ply or belt material exposed through the tread or sidewall, (2) Has any tread or sidewall separation, (3) Is flat or has an audible leak, or (4) Has a cut to the extent that the ply or belt material...

49 CFR 393.75 - Tires.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Has body ply or belt material exposed through the tread or sidewall, (2) Has any tread or sidewall separation, (3) Is flat or has an audible leak, or (4) Has a cut to the extent that the ply or belt material...

49 CFR 393.75 - Tires.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Has body ply or belt material exposed through the tread or sidewall, (2) Has any tread or sidewall separation, (3) Is flat or has an audible leak, or (4) Has a cut to the extent that the ply or belt material...

49 CFR 393.75 - Tires.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Has body ply or belt material exposed through the tread or sidewall, (2) Has any tread or sidewall separation, (3) Is flat or has an audible leak, or (4) Has a cut to the extent that the ply or belt material...

Computers for Interactive Learning.

ERIC Educational Resources Information Center

Grabowski, Barbara; Aggen, William

1984-01-01

Analyzes features of computer-based interactive video including sophisticated answer judging, diagnostic feedback, simulation, animation, audible tones, touch sensitive screen, function keys, and video enhancements, and matches these to the characteristics and pedagogical styles of learners. The learner characteristics discussed include internal…

Characterization of St. Lawrence blue whale vocalizations and their correlation with field observations

NASA Astrophysics Data System (ADS)

Berchok, Catherine L.

During four field seasons from 1998--2001, 115 hours of acoustic recordings were made in the presence of the well-studied St. Lawrence population of blue whales. The primary field site for this study was the estuary region of the St. Lawrence River (Quebec, Canada) with most recordings made between mid-August and late October. Effort was concentrated in the daylight hours, although occasionally extending past nightfall. An inexpensive and portable recording system was built that was easy to deploy and provided quality recordings in a variety of sea conditions. It consisted of a calibrated omni-directional hydrophone with a flat (+/-3dB) response from 5Hz to 800Hz; and a surface isolation buoy to minimize the vertical movement of the sensor. During the recording sessions detailed field notes were taken on all blue whales within sight, with individual identities confirmed through photo-identification work between sessions. Notes were also taken on all other species sighted during the recording sessions. Characterization of the more than one-thousand blue whale calls detected during this study revealed that the St. Lawrence repertoire is much more extensive than previously reported. Three infrasonic (<20Hz) and four audible range (30--200Hz) call types were detected in this study, with much time/frequency variation seen within each type. The infrasonic calls were long (5--30s) in duration and arranged into regularly patterned series. These calls were similar in call characteristics and spacing to those detected in the North Atlantic, but had much shorter and more variable patterned series. The audible call types were much shorter (1--4s), and occurred singly or in irregularly spaced clusters, although a special patterning was seen that contained both regular and irregular spaced components. Comparison of the daily, seasonal, and spatial distributions of calling behavior with those of several biological parameters revealed interesting differences between the three call types examined. The trends seen suggest a migratory, reproductive, or foraging context for the infrasonic calls. A closer-range social context is suggested for the audible downsweeps, which have been detected in foraging situations as well as in courtship displays. The audible mixed-pattern call type appears to have a primarily reproductive context.

CAVITATION SOUNDS DURING CERVICOTHORACIC SPINAL MANIPULATION.

PubMed

Dunning, James; Mourad, Firas; Zingoni, Andrea; Iorio, Raffaele; Perreault, Thomas; Zacharko, Noah; de Las Peñas, César Fernández; Butts, Raymond; Cleland, Joshua A

2017-08-01

No study has previously investigated the side, duration or number of audible cavitation sounds during high-velocity low-amplitude (HVLA) thrust manipulation to the cervicothoracic spine. The primary purpose was to determine which side of the spine cavitates during cervicothoracic junction (CTJ) HVLA thrust manipulation. Secondary aims were to calculate the average number of cavitations, the duration of cervicothoracic thrust manipulation, and the duration of a single cavitation. Quasi-experimental study. Thirty-two patients with upper trapezius myalgia received two cervicothoracic HVLA thrust manipulations targeting the right and left T1-2 articulation, respectively. Two high sampling rate accelerometers were secured bilaterally 25 mm lateral to midline of the T1-2 interspace. For each manipulation, two audio signals were extracted using Short-Time Fourier Transformation (STFT) and singularly processed via spectrogram calculation in order to evaluate the frequency content and number of instantaneous energy bursts of both signals over time for each side of the CTJ. Unilateral cavitation sounds were detected in 53 (91.4%) of 58 cervicothoracic HVLA thrust manipulations and bilateral cavitation sounds were detected in just five (8.6%) of the 58 thrust manipulations; that is, cavitation was significantly (p<0.001) more likely to occur unilaterally than bilaterally. In addition, cavitation was significantly (p<0.0001) more likely to occur on the side contralateral to the clinician's short-lever applicator. The mean number of audible cavitations per manipulation was 4.35 (95% CI 2.88, 5.76). The mean duration of a single manipulation was 60.77 ms (95% CI 28.25, 97.42) and the mean duration of a single audible cavitation was 4.13 ms (95% CI 0.82, 7.46). In addition to single-peak and multi-peak energy bursts, spectrogram analysis also demonstrated high frequency sounds, low frequency sounds, and sounds of multiple frequencies for all 58 manipulations. Cavitation was significantly more likely to occur unilaterally, and on the side contralateral to the short-lever applicator contact, during cervicothoracic HVLA thrust manipulation. Clinicians should expect multiple cavitation sounds when performing HVLA thrust manipulation to the CTJ. Due to the presence of multi-peak energy bursts and sounds of multiple frequencies, the cavitation hypothesis (i.e. intra-articular gas bubble collapse) alone appears unable to explain all of the audible sounds during HVLA thrust manipulation, and the possibility remains that several phenomena may be occurring simultaneously. 2b.

A vortex line for K-shell ionization of a carbon atom by electron impact

NASA Astrophysics Data System (ADS)

Ward, S. J.; Macek, J. H.

2014-10-01

We obtained using the Coulomb-Born approximation a deep minimum in the TDCS for K-shell ionization of a carbon atom by electron impact for the electron ejected in the scattering plane. The minimum is obtained for the kinematics of the energy of incident electron Ei = 1801.2 eV, the scattering angle θf = 4°, the energy of the ejected electron Ek = 5 . 5 eV, and the angle for the ejected electron θk = 239°. This minimum is due to a vortex in the velocity field. At the position of the vortex, the nodal lines of Re [ T ] and Im [ T ] intersect. We decomposed the CB1 T-matrix into its multipole components for the kinematics of a vortex, taking the z'-axis parallel to the direction of the momentum transfer vector. The m = +/- 1 dipole components are necessary to obtain a vortex. We also considered the electron to be ejected out of the scattering plane and obtained the positions of the vortex for different values of the y-component of momentum of the ejected electron, ky. We constructed the vortex line for the kinematics of Ei = 1801.2 eV and θf = 4°. S.J.W. and J.H.M. acknowledge support from NSF under Grant No. PHYS- 0968638 and from D.O.E. under Grant Number DE-FG02-02ER15283, respectively.

Shaping Cutter Original Profile for Fine-module Ratchet Teeth Cutting

NASA Astrophysics Data System (ADS)

Sharkov, O. V.; Koryagin, S. I.; Velikanov, N. L.

2018-03-01

The methods for determining geometric characteristics of a theoretical original profile of the cutter for cutting ratchet teeth with a module of 0.3–1.0 mm are considered in the article. Design models describing the shaping process of cutting edges of cutter teeth are developed. Systems of expressions for determining coordinates of the points of front and back edges of cutter teeth; the workpiece angles of rotation during the cutting process; the minimum cutter radius are received. The basic data when using the proposed technique are: radii of circumferences passing through cavities of cutter teeth and external cut teeth; the gradient angle and length of straight section of the front edge of a cut tooth; angles of rotation of the cutter and the workpiece at the moment of shaping.

Joining by plating: optimization of occluded angle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dini, J.W.; Johnson, H.R.; Kan, Y.R.

1978-11-01

An empirical method has been developed for predicting the minimum angle required for maximum joint strength for materials joined by plating. This is done through a proposed power law failure function, whose coefficients are taken from ring shear and conical head tensile data for plating/substrate combinations and whose exponent is determined from one set of plated-joint data. Experimental results are presented for Al-Ni-Al (7075-T6) and AM363-Ni-AM363 joints, and the failure function is used to predict joint strengths for Al-Ni-Al (2024-T6), UTi-Ni-UTi, and Be-Ti-Be.

Quality assessment of two- and three-dimensional unstructured meshes and validation of an upwind Euler flow solver

NASA Technical Reports Server (NTRS)

Woodard, Paul R.; Yang, Henry T. Y.; Batina, John T.

1992-01-01

Quality assessment procedures are described for two-dimensional and three-dimensional unstructured meshes. The procedures include measurement of minimum angles, element aspect ratios, stretching, and element skewness. Meshes about the ONERA M6 wing and the Boeing 747 transport configuration are generated using an advancing front method grid generation package of programs. Solutions of Euler's equations for these meshes are obtained at low angle-of-attack, transonic conditions. Results for these cases, obtained as part of a validation study demonstrate the accuracy of an implicit upwind Euler solution algorithm.

Light transfer through windows with external condensation

NASA Astrophysics Data System (ADS)

Zhu, Keyong; Li, Shaoling; Pilon, Laurent

2018-03-01

This study investigates systematically light transfer through windows supporting cap-shaped droplets on their external face. The presence of such droplets may have negative effects on the conversion efficiency of solar cells, distorts image quality of lenses, or hinders visibility through windows and windshields. Here, the directional-hemispherical transmittance was predicted by the Monte Carlo ray-tracing method. The droplets were monodisperse or polydisperse randomly distributed on the outside face of optically smooth windows. For nonabsorbing droplets, the diameter and size distribution did not have a significant effect on the window directional-hemispherical transmittance. The latter was nearly independent of contact angle for incident angle θi ≤ 30°. However, the directional-hemispherical transmittance decreased monotonously with increasing incident angle and droplet contact angle for contact angle θc ≤ 70° to reach a minimum at a contact angle θc,min beyond which it increased with increasing contact angle before reaching a plateau at large contact angles. This was attributed to total internal reflection at the back window/air and droplet/air interfaces. For absorbing droplets, the normal-hemispherical transmittance decreased significantly with increasing droplet contact angle, mean diameter, polydispersity, and projected surface area coverage due to strong absorption within the droplets. Moreover, the normal-hemispherical transmittance decreased with increasing contact angle for θc< 90° and remained constant and independent of the droplets' absorption index, mean diameter, and contact angle for θc ≥ 90°. Finally, Analytical expressions for the upper and lower bounds of the normal-hemispherical transmittance as a function of droplet contact angle, optical properties, and projected surface area coverage were derived.

Sneeze to leave: African wild dogs (Lycaon pictus) use variable quorum thresholds facilitated by sneezes in collective decisions.

PubMed

Walker, Reena H; King, Andrew J; McNutt, J Weldon; Jordan, Neil R

2017-09-13

In despotically driven animal societies, one or a few individuals tend to have a disproportionate influence on group decision-making and actions. However, global communication allows each group member to assess the relative strength of preferences for different options among their group-mates. Here, we investigate collective decisions by free-ranging African wild dog packs in Botswana. African wild dogs exhibit dominant-directed group living and take part in stereotyped social rallies: high energy greeting ceremonies that occur before collective movements. Not all rallies result in collective movements, for reasons that are not well understood. We show that the probability of rally success (i.e. group departure) is predicted by a minimum number of audible rapid nasal exhalations (sneezes), within the rally. Moreover, the number of sneezes needed for the group to depart (i.e. the quorum) was reduced whenever dominant individuals initiated rallies, suggesting that dominant participation increases the likelihood of a rally's success, but is not a prerequisite. As such, the 'will of the group' may override dominant preferences when the consensus of subordinates is sufficiently great. Our findings illustrate how specific behavioural mechanisms (here, sneezing) allow for negotiation (in effect, voting) that shapes decision-making in a wild, socially complex animal society. © 2017 The Author(s).

How Different Marker Sets Affect Joint Angles in Inverse Kinematics Framework.

PubMed

Mantovani, Giulia; Lamontagne, Mario

2017-04-01

The choice of marker set is a source of variability in motion analysis. Studies exist which assess the performance of marker sets when direct kinematics is used, but these results cannot be extrapolated to the inverse kinematic framework. Therefore, the purpose of this study was to examine the sensitivity of kinematic outcomes to inter-marker set variability in an inverse kinematic framework. The compared marker sets were plug-in-gait, University of Ottawa motion analysis model and a three-marker-cluster marker set. Walking trials of 12 participants were processed in opensim. The coefficient of multiple correlations was very good for sagittal (>0.99) and transverse (>0.92) plane angles, but worsened for the transverse plane (0.72). Absolute reliability indices are also provided for comparison among studies: minimum detectable change values ranged from 3 deg for the hip sagittal range of motion to 16.6 deg of the hip transverse range of motion. Ranges of motion of hip and knee abduction/adduction angles and hip and ankle rotations were significantly different among the three marker configurations (P < 0.001), with plug-in-gait producing larger ranges of motion. Although the same model was used for all the marker sets, the resulting minimum detectable changes were high and clinically relevant, which warns for caution when comparing studies that use different marker configurations, especially if they differ in the joint-defining markers.

Estrus- and steroid-induced changes in circadian rhythms in a diurnal rodent, Octodon degus.

PubMed

Labyak, S E; Lee, T M

1995-09-01

Diurnal Octodon degus exhibited marked alterations in activity and temperature in conjunction with the 3 wk estrous cycle when housed in LD12:12 light cycle. On the day of estrus, mean daily activity increases 109%, mean core temperature rises .4 degree C, activity onset is advanced 2 h, and amplitudes of both rhythms decline compared with the 3 days prior to estrus. On the day following estrus, activity onset was delayed 4.9 h, and mean activity and core temperature fell below that of the preestrus period. Ovariectomy significantly reduced mean temperature (.98 degree C) but did not significantly alter mean activity, and eliminated cyclic effects of estrus. Estrogen replacement led to a nonsignificant elevation in mean activity and core temperature with no change in the phase angle of entrainment. Progesterone replacement significantly reduced mean core temperature and mean activity, while only the phase angle difference between temperature minimum and activity onset was significantly altered. Intact degus maintained in constant darkness displayed only transient fluctuations in activity onset and temperature minimum during and after estrus. Estrogen or progesterone treatment of ovariectomized, free-running degus altered mean temperature and activity levels, but did not influence tau. Changes in phase angle of entrainment during estrus are not the result of hormone effects on the circadian clock but likely reflect increased or decreased levels of activity.

Solar axion search technique with correlated signals from multiple detectors

DOE PAGES

Xu, Wenqin; Elliott, Steven R.

2017-01-25

The coherent Bragg scattering of photons converted from solar axions inside crystals would boost the signal for axion-photon coupling enhancing experimental sensitivity for these hypothetical particles. Knowledge of the scattering angle of solar axions with respect to the crystal lattice is required to make theoretical predications of signal strength. Hence, both the lattice axis angle within a crystal and the absolute angle between the crystal and the Sun must be known. In this paper, we examine how the experimental sensitivity changes with respect to various experimental parameters. We also demonstrate that, in a multiple-crystal setup, knowledge of the relative axismore » orientation between multiple crystals can improve the experimental sensitivity, or equivalently, relax the precision on the absolute solar angle measurement. However, if absolute angles of all crystal axes are measured, we find that a precision of 2°–4° will suffice for an energy resolution of σ E = 0.04E and a flat background. Lastly, we also show that, given a minimum number of detectors, a signal model averaged over angles can substitute for precise crystal angular measurements, with some loss of sensitivity.« less

CFD investigation of pentamaran ship model with chine hull form on the resistance characteristics

NASA Astrophysics Data System (ADS)

Yanuar; Sulistyawati, W.

2018-03-01

This paper presents an investigation of pentamaran hull form with chine hull form to the effects of outriggers position, asymmetry, and deadrise angles on the resistance characteristics. The investigation to the resistance characteristics by modelling pentamaran hull form using chine with symmetrical main hull and asymmetric outboard on the variation deadrise angles: 25°, 30°, 35° and Froude number 0,1 to 0,7. On calm water resistance characteristics of six pentamaran models with chine-hull form examined by variation of deadrise angles by using CFD. Comparation with Wigley hull form, the maximum resistance drag reduction of the chine hull form was reduced by 15.81% on deadrise 25°, 13.8% on deadrise 30°, and 20.38% on deadrise 35°. While the smallest value of total resistance coefficient was generated from chine 35° at R/L:1/14 and R/L:1/7. Optimum hull form for minimum resistance has been obtained, so it is interesting to continue with angle of entrance and stem angle of hull for further research.

Testing a satellite automatic nutation control system. [on synchronous meteorological satellite

NASA Technical Reports Server (NTRS)

Hrasiar, J. A.

1974-01-01

Testing of a particular nutation control system for the synchronous meteorological satellite (SMS) is described. The test method and principles are applicable to nutation angle control for other satellites with similar requirements. During its ascent to synchronous orbit, a spacecraft like the SMS spins about its minimum-moment-of-inertia axis. An uncontrolled spacecraft in this state is unstable because torques due to fuel motion increase the nutation angle. However, the SMS is equipped with an automatic nutation control (ANC) system which will keep the nutation angle close to zero. Because correct operation of this system is critical to mission success, it was tested on an air-bearing table. The ANC system was mounted on the three-axis air-bearing table which was scaled to the SMS and equipped with appropriate sensors and thrusters. The table was spun up in an altitude chamber and nutation induced so that table motion simulated spacecraft motion. The ANC system was used to reduce the nutation angle. This dynamic test of the ANC system met all its objectives and provided confidence that the ANC system will control the SMS nutation angle.

33 CFR 86.05 - Sound signal intensity and range of audibility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... average background noise level at the listening posts (taken to be 68 dB in the octave band centered on... regarded as typical but under conditions of strong wind or high ambient noise level at the listening post...

30 CFR 75.1600-2 - Communication facilities; working sections; installation and maintenance requirements; audible or...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., however, that where trolley phones and telephones are both used, an alternate source of power for the trolley phone system is not required. (d) Trolley phones connected to the trolley wire shall be grounded...

Sonotropic effects of commercial air transport sound on birds.

DOT National Transportation Integrated Search

1962-03-01

The Electra sound spectrum contains an audible chirp which appears identical in frequency and wave form to the chirp of field crickets. Field observations strongly indicate the sound of the taxiing Electra exerts an attraction for starlings, and poss...

SU-F-J-200: An Improved Method for Event Selection in Compton Camera Imaging for Particle Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mackin, D; Beddar, S; Polf, J

2016-06-15

Purpose: The uncertainty in the beam range in particle therapy limits the conformality of the dose distributions. Compton scatter cameras (CC), which measure the prompt gamma rays produced by nuclear interactions in the patient tissue, can reduce this uncertainty by producing 3D images confirming the particle beam range and dose delivery. However, the high intensity and short time windows of the particle beams limit the number of gammas detected. We attempt to address this problem by developing a method for filtering gamma ray scattering events from the background by applying the known gamma ray spectrum. Methods: We used a 4more » stage Compton camera to record in list mode the energy deposition and scatter positions of gammas from a Co-60 source. Each CC stage contained a 4×4 array of CdZnTe crystal. To produce images, we used a back-projection algorithm and four filtering Methods: basic, energy windowing, delta energy (ΔE), or delta scattering angle (Δθ). Basic filtering requires events to be physically consistent. Energy windowing requires event energy to fall within a defined range. ΔE filtering selects events with the minimum difference between the measured and a known gamma energy (1.17 and 1.33 MeV for Co-60). Δθ filtering selects events with the minimum difference between the measured scattering angle and the angle corresponding to a known gamma energy. Results: Energy window filtering reduced the FWHM from 197.8 mm for basic filtering to 78.3 mm. ΔE and Δθ filtering achieved the best results, FWHMs of 64.3 and 55.6 mm, respectively. In general, Δθ filtering selected events with scattering angles < 40°, while ΔE filtering selected events with angles > 60°. Conclusion: Filtering CC events improved the quality and resolution of the corresponding images. ΔE and Δθ filtering produced similar results but each favored different events.« less

Analysis of Slug Test Response in a Fracture of a Large Dipping Angle

NASA Astrophysics Data System (ADS)

Chen, C.

2013-12-01

A number of cross-borehole slug tests were conducted in a Cenozoic folded sandstone formation, where a fracture has a dipping angle as large as 47°. As all the slug test models available in literature assume the formation to be horizontal, a slug test model taking into account the dipping angle effect is developed herein. Due to the presence of the dipping angle, there is a uniform regional groundwater flow, and the flow field generated by the test is not raidally symmetrical with respect to the test well. When the fracture hydraulic conductivity is relatively low, a larger dipping angle causes larger wellbore flow rates, leading to a faster recovery of the non-oscillatory test response. When the fracture hydraulic conductivity is relatively high, a larger dipping angle causes smaller wellbore heads, resulting in an increase of amplitude of the oscillatory test response; yet little influence on the frequency of oscillation. In general, neglecting the dipping angle may lead to an overestimate of hydraulic conductivity and an underestimate of the storage coefficient. The dipping angle effect is more pronounced for a larger storage coefficient, being less sensitive to transmissivity. An empirical relationship is developed for the minimum dipping angle, smaller than which the dipping angle effect can be safely neglected, as a function of the dimensionless storage coefficient. This empirical relationship helps evaluate whether or not the dipping angle needs to be considered in data analysis. The slug test data in the fracture of a 47°dipping angle is analyzed using the current model, and it is found that neglecting the dip angle can result in a 30% overestimate of transmissivity and a 61% underestimate of the storage coefficient.

Failure of Castlegate Sandstone under True Triaxial Loading

NASA Astrophysics Data System (ADS)

Ingraham, M. D.; Issen, K. A.; Holcomb, D. J.

2011-12-01

Understanding the stress conditions that cause deformation bands to form can provide insight into the geologic processes in a given location. In particular, understanding the relationship of the intermediate principal stress with respect to maximum and minimum compression when bands form, could provide useful information about the intermediate principal stress in field settings. Therefore, a series of tests were performed to investigate the effect of the intermediate principal stress on the mechanical response and failure of Castlegate sandstone under true triaxial states of stress. Constant mean stress tests were run at five different stress states ranging from: 1) intermediate principal stress equal to minimum compression to 2) intermediate principal stress equal to maximum compression. Failure occurred either through deformation band formation or apparent bulk compaction. Specimens that formed a deformation band experienced a stress drop at band formation. For a given level of intermediate principal stress, the peak stress increases with increasing mean stress. Additionally, as intermediate principal stress increases, the peak stress decreases for a given mean stress. Acoustic emissions (AE) recorded during testing were used to locate failure events in three-dimensional space within the sample. This allowed for more detailed investigation of the formation and propagation of the band(s) within the specimen. In specimens that appear to have undergone bulk compaction, AE events were randomly distributed throughout the sample. For specimens with bands, the band angles were measured as the angle between the maximum principal stress direction and the normal to the band that formed. Band angles tend to increase with increasing intermediate principal stress, and decrease with increasing mean stress. Results from the AE data shows that the band angle evolves during testing and the band that is expressed on the surface of the specimen at the conclusion of testing is not always the band that initially formed. AE results also show that low angle bands tend to be more diffuse than higher angle bands. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

14 CFR 25.771 - Pilot compartment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the propellers so that no member of the minimum flight crew (established under § 25.1523), or part of the controls, lies in the region between the plane of rotation of any inboard propeller and the surface generated by a line passing through the center of the propeller hub making an angle of five...

14 CFR 25.771 - Pilot compartment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the propellers so that no member of the minimum flight crew (established under § 25.1523), or part of the controls, lies in the region between the plane of rotation of any inboard propeller and the surface generated by a line passing through the center of the propeller hub making an angle of five...

14 CFR 25.771 - Pilot compartment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the propellers so that no member of the minimum flight crew (established under § 25.1523), or part of the controls, lies in the region between the plane of rotation of any inboard propeller and the surface generated by a line passing through the center of the propeller hub making an angle of five...

14 CFR 25.771 - Pilot compartment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the propellers so that no member of the minimum flight crew (established under § 25.1523), or part of the controls, lies in the region between the plane of rotation of any inboard propeller and the surface generated by a line passing through the center of the propeller hub making an angle of five...

Rugby and Mathematics: A Surprising Link among Geometry, the Conics, and Calculus.

ERIC Educational Resources Information Center

Jones, Troy; Jackson, Steven

2001-01-01

Describes a rugby problem designed to help students understand the maximum-minimum situation. Presents a series of explorations that locate an optimal place for kicking the ball to maximize the angle at the goalposts. Uses interactive geometry software to construct a model of the situation. Includes a sample student activity. (KHR)

14 CFR 29.177 - Static directional stability.

Code of Federal Regulations, 2011 CFR

2011-01-01

... pedal motion with throttle and collective controls held constant at the trim conditions specified in... control deflection for sideslip angles up to the lesser of— (1) ±25 degrees from trim at a speed of 15 knots less than the speed for minimum rate of descent varying linearly to ±10 degrees from trim at VNE...

Electron Pitch-Angle Distribution in Pressure Balance Structures Measured by Ulysses/SWOOPS

NASA Technical Reports Server (NTRS)

Yamauchi, Yohei; Suess, Steven T.; Sakurai, Takashi; Six, N. Frank (Technical Monitor)

2002-01-01

Pressure balance structures (PBSs) are a common feature in the high-latitude solar wind near solar minimum. From previous studies, PBSs are believed to be remnants of coronal plumes. Yamauchi et al [2002] investigated the magnetic structures of the PBSs, applying a minimum variance analysis to Ulysses/Magnetometer data. They found that PBSs contain structures like current sheets or plasmoids, and suggested that PBSs are associated with network activity such as magnetic reconnection in the photosphere at the base of polar plumes. We have investigated energetic electron data from Ulysses/SWOOPS to see whether bi-directional electron flow exists and we have found evidence supporting the earlier conclusions. We find that 45 ot of 53 PBSs show local bi-directional or isotopic electron flux or flux associated with current-sheet structure. Only five events show the pitch-angle distribution expected for Alfvenic fluctuations. We conclude that PBSs do contain magnetic structures such as current sheets or plasmoids that are expected as a result of network activity at the base of polar plumes.

Neutral points of skylight polarization observed during the total eclipse on 11 August 1999.

PubMed

Horváth, Gábor; Pomozi, István; Gál, József

2003-01-20

We report here on the observation of unpolarized (neutral) points in the sky during the total solar eclipse on 11 August 1999. Near the zenith a neutral point was observed at 450 nm at two different points of time during totality. Around this celestial point the distribution of the angle of polarization was heterogeneous: The electric field vectors on the one side were approximately perpendicular to those on the other side. At another moment of totality, near the zenith a local minimum of the degree of linear polarization occurred at 550 nm. Near the antisolar meridian, at a low elevation another two neutral points occurred at 450 nm at a certain moment during totality. Approximately at the position of these neutral points, at another moment of totality a local minimum of the degree of polarization occurred at 550 nm, whereas at 450 nm a neutral point was observed, around which the angle-of-polarization pattern was homogeneous: The electric field vectors were approximately horizontal on both sides of the neutral point.

[Study on once sampling quantitation based on information entropy of ISSR amplified bands of Houttuynia cordata].

PubMed

Wang, Haiqin; Liu, Wenlong; He, Fuyuan; Chen, Zuohong; Zhang, Xili; Xie, Xianggui; Zeng, Jiaoli; Duan, Xiaopeng

2012-02-01

To explore the once sampling quantitation of Houttuynia cordata through its DNA polymorphic bands that carried information entropy, from other form that the expression of traditional Chinese medicine polymorphism, genetic polymorphism, of traditional Chinese medicine. The technique of inter simple sequence repeat (ISSR) was applied to analyze genetic polymorphism of H. cordata samples from the same GAP producing area, the DNA genetic bands were transformed its into the information entropy, and the minimum once sampling quantitation with the mathematical mode was measured. One hundred and thirty-four DNA bands were obtained by using 9 screened ISSR primers to amplify from 46 strains DNA samples of H. cordata from the same GAP, the information entropy was H=0.365 6-0.978 6, and RSD was 14.75%. The once sampling quantitation was W=11.22 kg (863 strains). The "once minimum sampling quantitation" were calculated from the angle of the genetic polymorphism of H. cordata, and a great differences between this volume and the amount from the angle of fingerprint were found.

Classification of resistance to passive motion using minimum probability of error criterion.

PubMed

Chan, H C; Manry, M T; Kondraske, G V

1987-01-01

Neurologists diagnose many muscular and nerve disorders by classifying the resistance to passive motion of patients' limbs. Over the past several years, a computer-based instrument has been developed for automated measurement and parameterization of this resistance. In the device, a voluntarily relaxed lower extremity is moved at constant velocity by a motorized driver. The torque exerted on the extremity by the machine is sampled, along with the angle of the extremity. In this paper a computerized technique is described for classifying a patient's condition as 'Normal' or 'Parkinson disease' (rigidity), from the torque versus angle curve for the knee joint. A Legendre polynomial, fit to the curve, is used to calculate a set of eight normally distributed features of the curve. The minimum probability of error approach is used to classify the curve as being from a normal or Parkinson disease patient. Data collected from 44 different subjects was processes and the results were compared with an independent physician's subjective assessment of rigidity. There is agreement in better than 95% of the cases, when all of the features are used.

Extracting Vegetation Coverage in Dry-hot Valley Regions Based on Alternating Angle Minimum Algorithm

NASA Astrophysics Data System (ADS)

Y Yang, M.; Wang, J.; Zhang, Q.

2017-07-01

Vegetation coverage is one of the most important indicators for ecological environment change, and is also an effective index for the assessment of land degradation and desertification. The dry-hot valley regions have sparse surface vegetation, and the spectral information about the vegetation in such regions usually has a weak representation in remote sensing, so there are considerable limitations for applying the commonly-used vegetation index method to calculate the vegetation coverage in the dry-hot valley regions. Therefore, in this paper, Alternating Angle Minimum (AAM) algorithm of deterministic model is adopted for selective endmember for pixel unmixing of MODIS image in order to extract the vegetation coverage, and accuracy test is carried out by the use of the Landsat TM image over the same period. As shown by the results, in the dry-hot valley regions with sparse vegetation, AAM model has a high unmixing accuracy, and the extracted vegetation coverage is close to the actual situation, so it is promising to apply the AAM model to the extraction of vegetation coverage in the dry-hot valley regions.

Echolocation call intensity and directionality in flying short-tailed fruit bats, Carollia perspicillata (Phyllostomidae).

PubMed

Brinkløv, Signe; Jakobsen, Lasse; Ratcliffe, John M; Kalko, Elisabeth K V; Surlykke, Annemarie

2011-01-01

The directionality of bat echolocation calls defines the width of bats' sonar "view," while call intensity directly influences detection range since adequate sound energy must impinge upon objects to return audible echoes. Both are thus crucial parameters for understanding biosonar signal design. Phyllostomid bats have been classified as low intensity or "whispering bats," but recent data indicate that this designation may be inaccurate. Echolocation beam directionality in phyllostomids has only been measured through electrode brain-stimulation of restrained bats, presumably excluding active beam control via the noseleaf. Here, a 12-microphone array was used to measure echolocation call intensity and beam directionality in the frugivorous phyllostomid, Carollia perspicillata, echolocating in flight. The results showed a considerably narrower beam shape (half-amplitude beam angles of approximately 16° horizontally and 14° vertically) and louder echolocation calls [source levels averaging 99 dB sound pressure level (SPL) root mean square] for C. perspicillata than was found for this species when stationary. This suggests that naturally behaving phyllostomids shape their sound beam to achieve a longer and narrower sonar range than previously thought. C. perspicillata orient and forage in the forest interior and the narrow beam might be adaptive in clutter, by reducing the number and intensity of off-axis echoes.

Speech recognition and parent-ratings from auditory development questionnaires in children who are hard of hearing

PubMed Central

McCreery, Ryan W.; Walker, Elizabeth A.; Spratford, Meredith; Oleson, Jacob; Bentler, Ruth; Holte, Lenore; Roush, Patricia

2015-01-01

Objectives Progress has been made in recent years in the provision of amplification and early intervention for children who are hard of hearing. However, children who use hearing aids (HA) may have inconsistent access to their auditory environment due to limitations in speech audibility through their HAs or limited HA use. The effects of variability in children’s auditory experience on parent-report auditory skills questionnaires and on speech recognition in quiet and in noise were examined for a large group of children who were followed as part of the Outcomes of Children with Hearing Loss study. Design Parent ratings on auditory development questionnaires and children’s speech recognition were assessed for 306 children who are hard of hearing. Children ranged in age from 12 months to 9 years of age. Three questionnaires involving parent ratings of auditory skill development and behavior were used, including the LittlEARS Auditory Questionnaire, Parents Evaluation of Oral/Aural Performance in Children Rating Scale, and an adaptation of the Speech, Spatial and Qualities of Hearing scale. Speech recognition in quiet was assessed using the Open and Closed set task, Early Speech Perception Test, Lexical Neighborhood Test, and Phonetically-balanced Kindergarten word lists. Speech recognition in noise was assessed using the Computer-Assisted Speech Perception Assessment. Children who are hard of hearing were compared to peers with normal hearing matched for age, maternal educational level and nonverbal intelligence. The effects of aided audibility, HA use and language ability on parent responses to auditory development questionnaires and on children’s speech recognition were also examined. Results Children who are hard of hearing had poorer performance than peers with normal hearing on parent ratings of auditory skills and had poorer speech recognition. Significant individual variability among children who are hard of hearing was observed. Children with greater aided audibility through their HAs, more hours of HA use and better language abilities generally had higher parent ratings of auditory skills and better speech recognition abilities in quiet and in noise than peers with less audibility, more limited HA use or poorer language abilities. In addition to the auditory and language factors that were predictive for speech recognition in quiet, phonological working memory was also a positive predictor for word recognition abilities in noise. Conclusions Children who are hard of hearing continue to experience delays in auditory skill development and speech recognition abilities compared to peers with normal hearing. However, significant improvements in these domains have occurred in comparison to similar data reported prior to the adoption of universal newborn hearing screening and early intervention programs for children who are hard of hearing. Increasing the audibility of speech has a direct positive effect on auditory skill development and speech recognition abilities, and may also enhance these skills by improving language abilities in children who are hard of hearing. Greater number of hours of HA use also had a significant positive impact on parent ratings of auditory skills and children’s speech recognition. PMID:26731160

Gauche effect in 1,2-difluoroethane. Hyperconjugation, bent bonds, steric repulsion.

PubMed

Goodman, Lionel; Gu, Hongbing; Pophristic, Vojislava

2005-02-17

Natural bond orbital deletion calculations show that whereas the gauche preference arises from vicinal hyperconjugative interaction between anti C-H bonds and C-F* antibonds, the cis C-H/C-F* interactions are substantial (approximately 25% of the anti interaction). The established significantly >60 degrees FCCF dihedral angle for the equilibrium conformer can then be rationalized in terms of the hyperconjugation model alone by taking into account both anti interactions that maximize near 60 degrees and the smaller cis interactions that maximize at a much larger dihedral angle. This explanation does not invoke repulsive forces to rationalize the 72 degrees equilibrium conformer angle. The relative minimum energy for the trans conformer is the consequence of a balance between decreasing hyperconjugative stabilization and decreasing steric destabilization as the FCCF torsional angle approaches 180 degrees . The torsional coordinate is predicted to be strongly contaminated by CCF bending, with the result that approximately half of the trans --> gauche stabilization energy stems from mode coupling.

3D scanning characteristics of an amorphous silicon position sensitive detector array system.

PubMed

Contreras, Javier; Gomes, Luis; Filonovich, Sergej; Correia, Nuno; Fortunato, Elvira; Martins, Rodrigo; Ferreira, Isabel

2012-02-13

The 3D scanning electro-optical characteristics of a data acquisition prototype system integrating a 32 linear array of 1D amorphous silicon position sensitive detectors (PSD) were analyzed. The system was mounted on a platform for imaging 3D objects using the triangulation principle with a sheet-of-light laser. New obtained results reveal a minimum possible gap or simulated defect detection of approximately 350 μm. Furthermore, a first study of the angle for 3D scanning was also performed, allowing for a broad range of angles to be used in the process. The relationship between the scanning angle of the incident light onto the object and the image displacement distance on the sensor was determined for the first time in this system setup. Rendering of 3D object profiles was performed at a significantly higher number of frames than in the past and was possible for an incident light angle range of 15 ° to 85 °.

Trapped Ring Current Ion Dynamics During the 17-18 March 2015 Geomagnetic Storm Obtained from TWINS ENA Images

NASA Astrophysics Data System (ADS)

Perez, J. D.; Goldstein, J.; McComas, D. J.; Valek, P. W.; Fok, M. C. H.; Hwang, K. J.

2015-12-01

On 17-18 March 2015, there was a large (minimum SYM/H < -200 nT) geomagnetic storm. The Two Wide-Angle Imaging Neutral Atom Spectrometers (TWINS) mission, the first stereoscopic ENA magnetospheric imager, provides global images of the inner magnetosphere from which global distributions of ion flux, energy spectra, and pitch angle distributions are obtained. We will show how the observed ion pressure correlates with SYM/H. Examples of multiple peaks in the ion spatial distribution which may be due to multiple injections and/or energy and pitch angle dependent drift will be illustrated. Energy spectra will be shown to be non-Maxwellian, frequently having two peaks, one in the 10 keV range and another near 40 keV. Pitch angle distributions will be shown to have generally perpendicular anisotropy and that this can be time, space and energy dependent. The results are consistent with Comprehensive Inner Magnetosphere-Ionosphere (CIMI) model simulations.

Audible monitor for electroplating

NASA Technical Reports Server (NTRS)

Burowick, E. A.

1979-01-01

"No buzzer" indicates early problem in electroplating when parts are properly immersed into electropolating bath. Buzzer sounds when current flows through part; however, if current is cut, buzzer stops warning that parts must be removed and refinished thus preventing unnecessary waste of electrical energy and labor.

The Unusual Minimum of Cycle 23: Observations and Interpretation

NASA Astrophysics Data System (ADS)

Martens, Petrus C.; Nandy, D.; Munoz-Jaramillo, A.

2009-05-01

The current minimum of cycle 23 is unusual in its long duration, the very low level to which Total Solar Irradiance (TSI) has fallen, and the small flux of the open polar fields. The deep minimum of TSI seems to be related to an unprecedented dearth of polar faculae, and hence to the small amount of open flux. Based upon surface flux transport models it has been suggested that the causes of these phenomena may be an unusually vigorous meridional flow, or even a deviation from Joy's law resulting in smaller Joy angles than usual for emerging flux in cycle 23. There is also the possibility of a connection with the recently inferred emergence in polar regions of bipoles that systematically defy Hale's law. Much speculation has been going on as to the consequences of this exceptional minimum: are we entering another global minimum, is this the end of the 80 year period of exceptionally high solar activity, or is this just a statistical hiccup? Dynamo simulations are underway that may help answer this question. As an aside it must be mentioned that the current minimum of TSI puts an upper limit in the TSI input for global climate simulations during the Maunder minimum, and that a possible decrease in future solar activity will result in a very small but not insignificant reduction in the pace of global warming.

[Study on the disabilities in aged 0-7 years children in Shenzhen, China].

PubMed

Sun, Xi-bin; Qu, Cheng-yi; Yang, Lei; Yan, Jia-mu; Xie, Jian-wen; Chen, Yi-qing; Long, Mo; Liang, Wei; Li, Su-pei; Gao, Shou-yan; Yin, Dong-yi; Zhou, Wen-pei; Shi, Shuai; Hua, Fang; Zhou, Ben-li; Zhu, Shao-ming; Wang, Li; Feng, Dai-hao; Zhou, Lin

2003-11-01

To explore the prevalence of vision, mental, audibility, language, psychiatry, extremity, and influence factors in the 0 - 7 year olds. A total number of 77,727 0 - 7 year old children living in Shenzhen city were tested with tree phase screening under the Chinese standard of evaluation in disabilities. The prevalence of all disabilities was 5.59 per thousand (adjusted rate was 8.49 per thousand with a false negative of 3.1 per thousand ). The prevalence of mental disease was the highest (1.88 per thousand, with adjusted rate 3.43 per thousand ), the prevalence of language disability was 1.88 per thousand (including retarded language development, with adjusted rate 3.43 per thousand ). The prevalence rates of psychiatry, extremity and audibility disability were 1.59 per thousand, 1.56 per thousand, 1.11 per thousand respectively with of vision the lowest (0.37 per thousand ). The prevalence of all disabilities, audibility, language and mental was on the increase with age. The difference was statistically significant. Among all different age groups regarding psychiatric disease, the highest fell in the 2 - 4 year olds. The prevalence of extremity was not statistically different among age groups. The suspected agents of disease which occurred before or during pregnancy took up 45.7%. The prevalence of six kinds disabilities in Shenzhen was about 10 per thousand lower than that of the samples of the nation in 1989, but two times higher than that of similar studies in Japan. The prevalence rates of language and psychiatric disease were higher than that of the nation in 1989. The causation should be further studied.

Wind turbines and human health.

PubMed

Knopper, Loren D; Ollson, Christopher A; McCallum, Lindsay C; Whitfield Aslund, Melissa L; Berger, Robert G; Souweine, Kathleen; McDaniel, Mary

2014-01-01

The association between wind turbines and health effects is highly debated. Some argue that reported health effects are related to wind turbine operation [electromagnetic fields (EMF), shadow flicker, audible noise, low-frequency noise, infrasound]. Others suggest that when turbines are sited correctly, effects are more likely attributable to a number of subjective variables that result in an annoyed/stressed state. In this review, we provide a bibliographic-like summary and analysis of the science around this issue specifically in terms of noise (including audible, low-frequency noise, and infrasound), EMF, and shadow flicker. Now there are roughly 60 scientific peer-reviewed articles on this issue. The available scientific evidence suggests that EMF, shadow flicker, low-frequency noise, and infrasound from wind turbines are not likely to affect human health; some studies have found that audible noise from wind turbines can be annoying to some. Annoyance may be associated with some self-reported health effects (e.g., sleep disturbance) especially at sound pressure levels >40 dB(A). Because environmental noise above certain levels is a recognized factor in a number of health issues, siting restrictions have been implemented in many jurisdictions to limit noise exposure. These setbacks should help alleviate annoyance from noise. Subjective variables (attitudes and expectations) are also linked to annoyance and have the potential to facilitate other health complaints via the nocebo effect. Therefore, it is possible that a segment of the population may remain annoyed (or report other health impacts) even when noise limits are enforced. Based on the findings and scientific merit of the available studies, the weight of evidence suggests that when sited properly, wind turbines are not related to adverse health. Stemming from this review, we provide a number of recommended best practices for wind turbine development in the context of human health.

Wind Turbines and Human Health

PubMed Central

Knopper, Loren D.; Ollson, Christopher A.; McCallum, Lindsay C.; Whitfield Aslund, Melissa L.; Berger, Robert G.; Souweine, Kathleen; McDaniel, Mary

2014-01-01

The association between wind turbines and health effects is highly debated. Some argue that reported health effects are related to wind turbine operation [electromagnetic fields (EMF), shadow flicker, audible noise, low-frequency noise, infrasound]. Others suggest that when turbines are sited correctly, effects are more likely attributable to a number of subjective variables that result in an annoyed/stressed state. In this review, we provide a bibliographic-like summary and analysis of the science around this issue specifically in terms of noise (including audible, low-frequency noise, and infrasound), EMF, and shadow flicker. Now there are roughly 60 scientific peer-reviewed articles on this issue. The available scientific evidence suggests that EMF, shadow flicker, low-frequency noise, and infrasound from wind turbines are not likely to affect human health; some studies have found that audible noise from wind turbines can be annoying to some. Annoyance may be associated with some self-reported health effects (e.g., sleep disturbance) especially at sound pressure levels >40 dB(A). Because environmental noise above certain levels is a recognized factor in a number of health issues, siting restrictions have been implemented in many jurisdictions to limit noise exposure. These setbacks should help alleviate annoyance from noise. Subjective variables (attitudes and expectations) are also linked to annoyance and have the potential to facilitate other health complaints via the nocebo effect. Therefore, it is possible that a segment of the population may remain annoyed (or report other health impacts) even when noise limits are enforced. Based on the findings and scientific merit of the available studies, the weight of evidence suggests that when sited properly, wind turbines are not related to adverse health. Stemming from this review, we provide a number of recommended best practices for wind turbine development in the context of human health. PMID:24995266

Spontaneous obliteration of spontaneous vertebral arteriovenous fistula associated with fibromuscular dysplasia after partial surgery: A case report.

PubMed

Iampreechakul, Prasert; Siriwimonmas, Somkiet

2016-12-01

We describe a patient with spontaneous obliteration of spontaneous vertebral arteriovenous fistula (VAVF) associated with fibromuscular dysplasia (FMD) after partial surgery. A 52-year-old hypertensive female woke up one morning with left shoulder pain and weakness of the left upper extremity. A few days later, she developed left-sided audible bruit. She was treated for left frozen shoulder and supportive treatment for audible bruit for four years. She was referred from her general physician to a neurosurgeon because of left arm weakness. Physical examination showed signs of cervical radiculomyelopathy. Magnetic resonance imaging (MRI) showed an extradural mass on the left side of the cervical spinal canal from level C2 to C6. Provisional diagnosis was epidural vascular tumour. Laminectomy and partial removal of the mass was performed at level C5 to C6. Pathological report revealed suspected vascular malformation. Postoperative MRI showed thrombosed epidural vascular structure. Angiography showed dysplastic changes of both vertebral arteries representing FMD with VAVF of the left vertebral artery at level C1-C2. Two years after surgery, follow-up MRI demonstrated complete spontaneous resolution of the large thrombosed epidural vein. Disappearance of her audible bruit immediately after surgery and gradual improvement of her cervical radiculomyelopathy were observed after two years of clinical follow-up. From the literature, we found another 11 patients with 12 VAVFs who had spontaneous obliteration or cure of their fistulas. In the present case, spontaneous obliteration of the fistula seems to correlate with surgery inducing closure of the epidural venous exit leading to thrombosis of the enlarged epidural draining vein. © The Author(s) 2016.

Triple differential cross-sections of Ne (2s2) in coplanar to perpendicular plane geometry

NASA Astrophysics Data System (ADS)

Chen, L. Q.; Khajuria, Y.; Chen, X. J.; Xu, K. Z.

2003-10-01

The distorted wave Born approximation (DWBA) with the spin averaged static exchange potential has been used to calculate the triple differential cross-sections (TDCSs) for Ne (2s^2) ionization by electron impact in coplanar to perpendicular plane symmetric geometry at 110.5 eV incident electron energy. The present theoretical results at gun angles Psi = 0^circ (coplanar symmetric geometry) and Psi = 90^circ (perpendicular plane geometry) are in satisfactory agreement with the available experimental data. A deep interference minimum appears in the TDCS in the coplanar symmetric geometry and a strong peak at scattering angle xi = 90^circ caused by the single collision mechanism has been observed in the perpendicular plane geometry. The TDCSs at the gun angles Psi = 30^circ, and Psi = 60^circ are predicted.

Error reduction program: A progress report

NASA Technical Reports Server (NTRS)

Syed, S. A.

1984-01-01

Five finite differences schemes were evaluated for minimum numerical diffusion in an effort to identify and incorporate the best error reduction scheme into a 3D combustor performance code. Based on this evaluated, two finite volume method schemes were selected for further study. Both the quadratic upstream differencing scheme (QUDS) and the bounded skew upstream differencing scheme two (BSUDS2) were coded into a two dimensional computer code and their accuracy and stability determined by running several test cases. It was found that BSUDS2 was more stable than QUDS. It was also found that the accuracy of both schemes is dependent on the angle that the streamline make with the mesh with QUDS being more accurate at smaller angles and BSUDS2 more accurate at larger angles. The BSUDS2 scheme was selected for extension into three dimensions.

Solvent effect on the conformation of Benzil

NASA Astrophysics Data System (ADS)

Pawelka, Z.; Koll, A.; Zeegers-Huyskens, Th.

2001-10-01

The conformation of benzil is investigated by PM3 and density functional theory (B3LYP) combined with the 6-31G(d,p) basis set. The variation of the relative energy with the Odbnd C-Cdbnd O torsion angle indicates only one rather flat minimum, reflecting the flexibility of the benzil molecule. The dipole moment is measured in several organic solvents of various polarity and the IR and Raman spectra investigated in the Cdbnd O stretching region in the same solvents. The torsional Odbnd C-Cdbnd O angle is evaluated from the dipolar and vibrational data. The results indicate that, in all the solvents, benzil is in a skewed conformation, the cisoid conformation being slightly favoured when the polarity of the solvent increases. The contribution of electrostatic and specific interactions to the reduction of the torsional angle is discussed.

Common angle plots as perception-true visualizations of categorical associations.

PubMed

Hofmann, Heike; Vendettuoli, Marie

2013-12-01

Visualizations are great tools of communications-they summarize findings and quickly convey main messages to our audience. As designers of charts we have to make sure that information is shown with a minimum of distortion. We have to also consider illusions and other perceptual limitations of our audience. In this paper we discuss the effect and strength of the line width illusion, a Muller-Lyer type illusion, on designs related to displaying associations between categorical variables. Parallel sets and hammock plots are both affected by line width illusions. We introduce the common-angle plot as an alternative method for displaying categorical data in a manner that minimizes the effect from perceptual illusions. Results from user studies both highlight the need for addressing line-width illusions in displays and provide evidence that common angle charts successfully resolve this issue.

INTERNAL LIMITING MEMBRANE PEELING VERSUS INVERTED FLAP TECHNIQUE FOR TREATMENT OF FULL-THICKNESS MACULAR HOLES: A COMPARATIVE STUDY IN A LARGE SERIES OF PATIENTS.

PubMed

Rizzo, Stanislao; Tartaro, Ruggero; Barca, Francesco; Caporossi, Tomaso; Bacherini, Daniela; Giansanti, Fabrizio

2017-12-08

The inverted flap (IF) technique has recently been introduced in macular hole (MH) surgery. The IF technique has shown an increase of the success rate in the case of large MHs and in MHs associated with high myopia. This study reports the anatomical and functional results in a large series of patients affected by MH treated using pars plana vitrectomy and gas tamponade combined with internal limiting membrane (ILM) peeling or IF. This is a retrospective, consecutive, nonrandomized comparative study of patients affected by idiopathic or myopic MH treated using small-gauge pars plana vitrectomy (25- or 23-gauge) between January 2011 and May 2016. The patients were divided into two groups according to the ILM removal technique (complete removal vs. IF). A subgroup analysis was performed according to the MH diameter (MH < 400 µm and MH ≥ 400 µm), axial length (AL < 26 mm and AL ≥ 26 mm), and the presence of chorioretinal atrophy in the macular area (present or absent). We included 620 eyes of 570 patients affected by an MH, 300 patients underwent pars plana vitrectomy and ILM peeling and 320 patients underwent pars plana vitrectomy and IF. Overall, 84.94% of the patients had complete anatomical success characterized by MH closure after the operation. In particular, among the patients who underwent only ILM peeling the closure rate was 78.75%; among the patients who underwent the IF technique, it was 91.93% (P = 0.001); and among the patients affected by full-thickness MH ≥400 µm, success was achieved in 95.6% of the cases in the IF group and in 78.6% in the ILM peeling group (P = 0.001); among the patients with an axial length ≥26 mm, success was achieved in 88.4% of the cases in the IF group and in 38.9% in the ILM peeling group (P = 0.001). Average preoperative best-corrected visual acuity was 0.77 (SD = 0.32) logarithm of the minimum angle of resolution (20/118 Snellen) in the peeling group and 0.74 (SD = 0.33) logarithm of the minimum angle of resolution (20/110 Snellen) in the IF group (P = 0.31). Mean postoperative best-corrected visual acuity was 0.52 (SD = 0.42) logarithm of the minimum angle of resolution (20/66 Snellen) in the peeling group and 0.43 (SD = 0.31) logarithm of the minimum angle of resolution (20/53 Snellen) in the IF group (P = 0.003). Vitrectomy associated with the inverted ILM flap technique seems to be effective surgery for idiopathic and myopic large MHs, improving both functional and anatomical outcomes.

Orbit and geometry constraints on the design and operation of a long-life SIRTF mission. [Shuttle Infrared Telescope Facility

NASA Technical Reports Server (NTRS)

Jackson, R. W.

1984-01-01

For a long-life SIRTF mission, the ability of the telescope to observe targets everywhere in the sky is an important requirement. For low-inclination orbits, a telescope aperture shade must be designed for Sun and Earth Limb avoidance angles of 50 deg to 60 deg to prevent unwanted radiation from entering the telescope. The minimum orbit inclination depends on the Earth Limb avoidance angle. About 30 percent of the sky will be prohibited for observations during any day in orbit, with about 100 days in orbit required to observe the entire sky.

46 CFR 63.15-7 - Alarms.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING AUTOMATIC AUXILIARY BOILERS General Requirements § 63.15-7 Alarms. (a) An audible alarm must automatically sound when a flame safety system shutdown occurs. A visible indicator must indicate that the shutdown was caused by the flame safety system...

46 CFR 63.15-7 - Alarms.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING AUTOMATIC AUXILIARY BOILERS General Requirements § 63.15-7 Alarms. (a) An audible alarm must automatically sound when a flame safety system shutdown occurs. A visible indicator must indicate that the shutdown was caused by the flame safety system...

46 CFR 63.15-7 - Alarms.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING AUTOMATIC AUXILIARY BOILERS General Requirements § 63.15-7 Alarms. (a) An audible alarm must automatically sound when a flame safety system shutdown occurs. A visible indicator must indicate that the shutdown was caused by the flame safety system...

46 CFR 63.15-7 - Alarms.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING AUTOMATIC AUXILIARY BOILERS General Requirements § 63.15-7 Alarms. (a) An audible alarm must automatically sound when a flame safety system shutdown occurs. A visible indicator must indicate that the shutdown was caused by the flame safety system...

46 CFR 63.15-7 - Alarms.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING AUTOMATIC AUXILIARY BOILERS General Requirements § 63.15-7 Alarms. (a) An audible alarm must automatically sound when a flame safety system shutdown occurs. A visible indicator must indicate that the shutdown was caused by the flame safety system...

40 CFR 65.143 - Closed vent systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... storage vessel, process vent, transfer rack, or equipment leaks. (1) Collection of emissions. Each closed... material from a storage vessel, transfer rack or equipment leaks. Inspection records shall be generated as... (B) Conduct annual visual inspections for visible, audible, or olfactory indications of leaks. (ii...

75 FR 34486 - Petitions for Modification

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-17

... while continuously monitoring for methane levels. Immediately prior to the use of the non-permissible equipment, the mine atmosphere will be tested for methane within 6 inches, and would be continuously monitored with an approved instrument capable of providing both visual and audible alarms. Methane levels...

46 CFR 151.40-10 - Operational requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... shall operate when either the pressure or the temperature exceeds the operating limits of the system... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES BARGES... Operational requirements. Control systems, required by Table 151.05 shall be provided with an audible or...

Analysis of modeling cumulative noise from simultaneous flights volume 2 : supplemental analysis

DOT National Transportation Integrated Search

2012-12-31

This is the second of two volumes of the report on modeling cumulative noise from simultaneous flights. This volume examines the effect of several modeling input cases on Percent Time Audible results calculated by the Integrated Noise Model. The case...

29 CFR 1926.555 - Conveyors.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors § 1926.555... operator's station. Conveyor systems shall be equipped with an audible warning signal to be sounded... tagged out with a “Do Not Operate” tag during repairs and when operation is hazardous to employees...

29 CFR 1926.555 - Conveyors.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors § 1926.555... operator's station. Conveyor systems shall be equipped with an audible warning signal to be sounded... tagged out with a “Do Not Operate” tag during repairs and when operation is hazardous to employees...

29 CFR 1926.555 - Conveyors.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors § 1926.555... operator's station. Conveyor systems shall be equipped with an audible warning signal to be sounded... tagged out with a “Do Not Operate” tag during repairs and when operation is hazardous to employees...

29 CFR 1926.555 - Conveyors.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors § 1926.555... operator's station. Conveyor systems shall be equipped with an audible warning signal to be sounded... tagged out with a “Do Not Operate” tag during repairs and when operation is hazardous to employees...

10 CFR 70.24 - Criticality accident requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Criticality accident requirements. 70.24 Section 70.24... Applications § 70.24 Criticality accident requirements. (a) Each licensee authorized to possess special nuclear...-sensitive radiation detectors which will energize clearly audible alarm signals if accidental criticality...

10 CFR 70.24 - Criticality accident requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Criticality accident requirements. 70.24 Section 70.24... Applications § 70.24 Criticality accident requirements. (a) Each licensee authorized to possess special nuclear...-sensitive radiation detectors which will energize clearly audible alarm signals if accidental criticality...

10 CFR 70.24 - Criticality accident requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Criticality accident requirements. 70.24 Section 70.24... Applications § 70.24 Criticality accident requirements. (a) Each licensee authorized to possess special nuclear...-sensitive radiation detectors which will energize clearly audible alarm signals if accidental criticality...

10 CFR 70.24 - Criticality accident requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Criticality accident requirements. 70.24 Section 70.24... Applications § 70.24 Criticality accident requirements. (a) Each licensee authorized to possess special nuclear...-sensitive radiation detectors which will energize clearly audible alarm signals if accidental criticality...

10 CFR 70.24 - Criticality accident requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Criticality accident requirements. 70.24 Section 70.24... Applications § 70.24 Criticality accident requirements. (a) Each licensee authorized to possess special nuclear...-sensitive radiation detectors which will energize clearly audible alarm signals if accidental criticality...

A Noise Level Prediction Method Based on Electro-Mechanical Frequency Response Function for Capacitors

PubMed Central

Zhu, Lingyu; Ji, Shengchang; Shen, Qi; Liu, Yuan; Li, Jinyu; Liu, Hao

2013-01-01

The capacitors in high-voltage direct-current (HVDC) converter stations radiate a lot of audible noise which can reach higher than 100 dB. The existing noise level prediction methods are not satisfying enough. In this paper, a new noise level prediction method is proposed based on a frequency response function considering both electrical and mechanical characteristics of capacitors. The electro-mechanical frequency response function (EMFRF) is defined as the frequency domain quotient of the vibration response and the squared capacitor voltage, and it is obtained from impulse current experiment. Under given excitations, the vibration response of the capacitor tank is the product of EMFRF and the square of the given capacitor voltage in frequency domain, and the radiated audible noise is calculated by structure acoustic coupling formulas. The noise level under the same excitations is also measured in laboratory, and the results are compared with the prediction. The comparison proves that the noise prediction method is effective. PMID:24349105

Comparing phase-sensitive and phase-insensitive echolocation target images using a monaural audible sonar.

PubMed

Kuc, Roman

2018-04-01

This paper describes phase-sensitive and phase-insensitive processing of monaural echolocation waveforms to generate target maps. Composite waveforms containing both the emission and echoes are processed to estimate the target impulse response using an audible sonar. Phase-sensitive processing yields the composite signal envelope, while phase-insensitive processing that starts with the composite waveform power spectrum yields the envelope of the autocorrelation function. Analysis and experimental verification show that multiple echoes form an autocorrelation function that produces near-range phantom-reflector artifacts. These artifacts interfere with true target echoes when the first true echo occurs at a time that is less than the total duration of the target echoes. Initial comparison of phase-sensitive and phase-insensitive maps indicates that both display important target features, indicating that phase is not vital. A closer comparison illustrates the improved resolution of phase-sensitive processing, the near-range phantom-reflectors produced by phase-insensitive processing, and echo interference and multiple reflection artifacts that were independent of the processing.

Meteor fireball sounds identified

NASA Technical Reports Server (NTRS)

Keay, Colin

1992-01-01

Sounds heard simultaneously with the flight of large meteor fireballs are electrical in origin. Confirmation that Extra/Very Low Frequency (ELF/VLF) electromagnetic radiation is produced by the fireball was obtained by Japanese researchers. Although the generation mechanism is not fully understood, studies of the Meteorite Observation and Recovery Project (MORP) and other fireball data indicate that interaction with the atmosphere is definitely responsible and the cut-off magnitude of -9 found for sustained electrophonic sounds is supported by theory. Brief bursts of ELF/VLF radiation may accompany flares or explosions of smaller fireballs, producing transient sounds near favorably placed observers. Laboratory studies show that mundane physical objects can respond to electrical excitation and produce audible sounds. Reports of electrophonic sounds should no longer be discarded. A catalog of over 300 reports relating to electrophonic phenomena associated with meteor fireballs, aurorae, and lightning was assembled. Many other reports have been cataloged in Russian. These may assist the full solution of the similar long-standing and contentious mystery of audible auroral displays.

High-speed imaging, acoustic features, and aeroacoustic computations of jet noise from Strombolian (and Vulcanian) explosions

NASA Astrophysics Data System (ADS)

Taddeucci, J.; Sesterhenn, J.; Scarlato, P.; Stampka, K.; Del Bello, E.; Pena Fernandez, J. J.; Gaudin, D.

2014-05-01

High-speed imaging of explosive eruptions at Stromboli (Italy), Fuego (Guatemala), and Yasur (Vanuatu) volcanoes allowed visualization of pressure waves from seconds-long explosions. From the explosion jets, waves radiate with variable geometry, timing, and apparent direction and velocity. Both the explosion jets and their wave fields are replicated well by numerical simulations of supersonic jets impulsively released from a pressurized vessel. The scaled acoustic signal from one explosion at Stromboli displays a frequency pattern with an excellent match to those from the simulated jets. We conclude that both the observed waves and the audible sound from the explosions are jet noise, i.e., the typical acoustic field radiating from high-velocity jets. Volcanic jet noise was previously quantified only in the infrasonic emissions from large, sub-Plinian to Plinian eruptions. Our combined approach allows us to define the spatial and temporal evolution of audible jet noise from supersonic jets in small-scale volcanic eruptions.

Industrial wind turbines and adverse health effects.

PubMed

Jeffery, Roy D; Krogh, Carmen M E; Horner, Brett

2014-01-01

Some people living in the environs of industrial wind turbines (IWTs) report experiencing adverse health and socioeconomic effects. This review considers the hypothesis that annoyance from audible IWTs is the cause of these adverse health effects. We searched PubMed and Google Scholar for articles published since 2000 that included the terms "wind turbine health," "wind turbine infrasound," "wind turbine annoyance," "noise annoyance" or "low frequency noise" in the title or abstract. Industrial wind turbines produce sound that is perceived to be more annoying than other sources of sound. Reported effects from exposure to IWTs are consistent with well-known stress effects from persistent unwanted sound. If placed too close to residents, IWTs can negatively affect the physical, mental and social well-being of people. There is sufficient evidence to support the conclusion that noise from audible IWTs is a potential cause of health effects. Inaudible low-frequency noise and infrasound from IWTs cannot be ruled out as plausible causes of health effects.

Photoacoustic Sounds from Meteors.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spalding, Richard E.; Tencer, John; Sweatt, William C.

2015-03-01

High-speed photometric observations of meteor fireballs have shown that they often produce high-amplitude light oscillations with frequency components in the kHz range, and in some cases exhibit strong millisecond flares. We built a light source with similar characteristics and illuminated various materials in the laboratory, generating audible sounds. Models suggest that light oscillations and pulses can radiatively heat dielectric materials, which in turn conductively heats the surrounding air on millisecond timescales. The sound waves can be heard if the illuminated material is sufficiently close to the observer’s ears. The mechanism described herein may explain many reports of meteors that appearmore » to be audible while they are concurrently visible in the sky and too far away for sound to have propagated to the observer. This photoacoustic (PA) explanation provides an alternative to electrophonic (EP) sounds hypothesized to arise from electromagnetic coupling of plasma oscillation in the meteor wake to natural antennas in the vicinity of an observer.« less

Concealed wire tracing apparatus

DOEpatents

Kronberg, J.W.

1994-05-31

An apparatus and method that combines a signal generator and a passive signal receiver to detect and record the path of partially or completely concealed electrical wiring without disturbing the concealing surface is disclosed. The signal generator applies a series of electrical pulses to the selected wiring of interest. The applied pulses create a magnetic field about the wiring that can be detected by a coil contained within the signal receiver. An audible output connected to the receiver and driven by the coil reflects the receivers position with respect to the wiring. The receivers audible signal is strongest when the receiver is directly above the wiring and the long axis of the receivers coil is parallel to the wiring. A marking means is mounted on the receiver to mark the location of the wiring as the receiver is directed over the wiring's concealing surface. Numerous marks made on various locations of the concealing surface will trace the path of the wiring of interest. 4 figs.

Unvoiced Speech Recognition Using Tissue-Conductive Acoustic Sensor

NASA Astrophysics Data System (ADS)

Heracleous, Panikos; Kaino, Tomomi; Saruwatari, Hiroshi; Shikano, Kiyohiro

2006-12-01

We present the use of stethoscope and silicon NAM (nonaudible murmur) microphones in automatic speech recognition. NAM microphones are special acoustic sensors, which are attached behind the talker's ear and can capture not only normal (audible) speech, but also very quietly uttered speech (nonaudible murmur). As a result, NAM microphones can be applied in automatic speech recognition systems when privacy is desired in human-machine communication. Moreover, NAM microphones show robustness against noise and they might be used in special systems (speech recognition, speech transform, etc.) for sound-impaired people. Using adaptation techniques and a small amount of training data, we achieved for a 20 k dictation task a[InlineEquation not available: see fulltext.] word accuracy for nonaudible murmur recognition in a clean environment. In this paper, we also investigate nonaudible murmur recognition in noisy environments and the effect of the Lombard reflex on nonaudible murmur recognition. We also propose three methods to integrate audible speech and nonaudible murmur recognition using a stethoscope NAM microphone with very promising results.

A noise level prediction method based on electro-mechanical frequency response function for capacitors.

PubMed

Zhu, Lingyu; Ji, Shengchang; Shen, Qi; Liu, Yuan; Li, Jinyu; Liu, Hao

2013-01-01

The capacitors in high-voltage direct-current (HVDC) converter stations radiate a lot of audible noise which can reach higher than 100 dB. The existing noise level prediction methods are not satisfying enough. In this paper, a new noise level prediction method is proposed based on a frequency response function considering both electrical and mechanical characteristics of capacitors. The electro-mechanical frequency response function (EMFRF) is defined as the frequency domain quotient of the vibration response and the squared capacitor voltage, and it is obtained from impulse current experiment. Under given excitations, the vibration response of the capacitor tank is the product of EMFRF and the square of the given capacitor voltage in frequency domain, and the radiated audible noise is calculated by structure acoustic coupling formulas. The noise level under the same excitations is also measured in laboratory, and the results are compared with the prediction. The comparison proves that the noise prediction method is effective.

Audible thunder characteristic and the relation between peak frequency and lightning parameters

NASA Astrophysics Data System (ADS)

Yuhua, Ouyang; Ping, Yuan

2012-02-01

In recent summers, some natural lightning optical spectra and audible thunder signals were observed. Twelve events on 15 August 2008 are selected as samples since some synchronizing information about them are obtained, such as lightning optical spectra, surface E-field changes, etc. By using digital filter and Fourier transform, thunder frequency spectra in observation location have been calculated. Then the two main propagation effects, finite amplitude propagation and attenuation by air, are calculated. Upon that we take the test thunder frequency spectra and work backward to recalculate the original frequency spectra near generation location. Thunder frequency spectra and the frequency distribution varying with distance are researched. According to the theories on plasma, the channel temperature and electron density are further calculated by transition parameters of lines in lightning optical spectra. Pressure and the average ionization degree of each discharge channel are obtained by using Saha equations, charge conservation equations and particle conservation equations. Moreover, the relationship between the peak frequency of each thunder and channel parameters of the lightning is studied.

Adaptive color halftoning for minimum perceived error using the blue noise mask

NASA Astrophysics Data System (ADS)

Yu, Qing; Parker, Kevin J.

1997-04-01

Color halftoning using a conventional screen requires careful selection of screen angles to avoid Moire patterns. An obvious advantage of halftoning using a blue noise mask (BNM) is that there are no conventional screen angle or Moire patterns produced. However, a simple strategy of employing the same BNM on all color planes is unacceptable in case where a small registration error can cause objectionable color shifts. In a previous paper by Yao and Parker, strategies were presented for shifting or inverting the BNM as well as using mutually exclusive BNMs for different color planes. In this paper, the above schemes will be studied in CIE-LAB color space in terms of root mean square error and variance for luminance channel and chrominance channel respectively. We will demonstrate that the dot-on-dot scheme results in minimum chrominance error, but maximum luminance error and the 4-mask scheme results in minimum luminance error but maximum chrominance error, while the shift scheme falls in between. Based on this study, we proposed a new adaptive color halftoning algorithm that takes colorimetric color reproduction into account by applying 2-mutually exclusive BNMs on two different color planes and applying an adaptive scheme on other planes to reduce color error. We will show that by having one adaptive color channel, we obtain increased flexibility to manipulate the output so as to reduce colorimetric error while permitting customization to specific printing hardware.

Two-Diffraction-Order, Beam-Splitting, Imaging Spectrometer

NASA Technical Reports Server (NTRS)

Labaw, Clayton C.; Burns, Ronald N.

1995-01-01

Two-octave imaging spectrometer utilizes light of two harmonically related wavelengths diffracted to harmonically related orders at same angles, followed by separation via dichroic beam splitter before final imaging. Conceptual design of spectrometer calls for minimum number of optical elements to achieve coverage of required visible and near-infrared wavelengths in instrument of reduced size, weight, and cost.

14 CFR 27.177 - Static directional stability.

Code of Federal Regulations, 2011 CFR

2011-01-01

... with the throttle and collective controls held constant at the trim conditions specified in § 27.175(a... for sideslip angles up to the lesser of— (1) ±25 degrees from trim at a speed of 15 knots less than the speed for minimum rate of descent varying linearly to ±10 degrees from trim at VNE; (2) The steady...

Seismic analysis for translational failure of landfills with retaining walls.

PubMed

Feng, Shi-Jin; Gao, Li-Ya

2010-11-01

In the seismic impact zone, seismic force can be a major triggering mechanism for translational failures of landfills. The scope of this paper is to develop a three-part wedge method for seismic analysis of translational failures of landfills with retaining walls. The approximate solution of the factor of safety can be calculated. Unlike previous conventional limit equilibrium methods, the new method is capable of revealing the effects of both the solid waste shear strength and the retaining wall on the translational failures of landfills during earthquake. Parameter studies of the developed method show that the factor of safety decreases with the increase of the seismic coefficient, while it increases quickly with the increase of the minimum friction angle beneath waste mass for various horizontal seismic coefficients. Increasing the minimum friction angle beneath the waste mass appears to be more effective than any other parameters for increasing the factor of safety under the considered condition. Thus, selecting liner materials with higher friction angle will considerably reduce the potential for translational failures of landfills during earthquake. The factor of safety gradually increases with the increase of the height of retaining wall for various horizontal seismic coefficients. A higher retaining wall is beneficial to the seismic stability of the landfill. Simply ignoring the retaining wall will lead to serious underestimation of the factor of safety. Besides, the approximate solution of the yield acceleration coefficient of the landfill is also presented based on the calculated method. Copyright © 2010 Elsevier Ltd. All rights reserved.

Energy Landscapes for the Self-Assembly of Supramolecular Polyhedra

NASA Astrophysics Data System (ADS)

Russell, Emily R.; Menon, Govind

2016-06-01

We develop a mathematical model for the energy landscape of polyhedral supramolecular cages recently synthesized by self-assembly (Sun et al. in Science 328:1144-1147, 2010). Our model includes two essential features of the experiment: (1) geometry of the organic ligands and metallic ions; and (2) combinatorics. The molecular geometry is used to introduce an energy that favors square-planar vertices (modeling {Pd}^{2+} ions) and bent edges with one of two preferred opening angles (modeling boomerang-shaped ligands of two types). The combinatorics of the model involve two-colorings of edges of polyhedra with four-valent vertices. The set of such two-colorings, quotiented by the octahedral symmetry group, has a natural graph structure and is called the combinatorial configuration space. The energy landscape of our model is the energy of each state in the combinatorial configuration space. The challenge in the computation of the energy landscape is a combinatorial explosion in the number of two-colorings of edges. We describe sampling methods based on the symmetries of the configurations and connectivity of the configuration graph. When the two preferred opening angles encompass the geometrically ideal angle, the energy landscape exhibits a very low-energy minimum for the most symmetric configuration at equal mixing of the two angles, even when the average opening angle does not match the ideal angle.

Sample Training Based Wildfire Segmentation by 2D Histogram θ-Division with Minimum Error

PubMed Central

Dong, Erqian; Sun, Mingui; Jia, Wenyan; Zhang, Dengyi; Yuan, Zhiyong

2013-01-01

A novel wildfire segmentation algorithm is proposed with the help of sample training based 2D histogram θ-division and minimum error. Based on minimum error principle and 2D color histogram, the θ-division methods were presented recently, but application of prior knowledge on them has not been explored. For the specific problem of wildfire segmentation, we collect sample images with manually labeled fire pixels. Then we define the probability function of error division to evaluate θ-division segmentations, and the optimal angle θ is determined by sample training. Performances in different color channels are compared, and the suitable channel is selected. To further improve the accuracy, the combination approach is presented with both θ-division and other segmentation methods such as GMM. Our approach is tested on real images, and the experiments prove its efficiency for wildfire segmentation. PMID:23878526

Technique for enhancing the power output of an electrostatic generator employing parametric resonance

DOEpatents

Post, Richard F.

2016-02-23

A circuit-based technique enhances the power output of electrostatic generators employing an array of axially oriented rods or tubes or azimuthal corrugated metal surfaces for their electrodes. During generator operation, the peak voltage across the electrodes occurs at an azimuthal position that is intermediate between the position of minimum gap and maximum gap. If this position is also close to the azimuthal angle where the rate of change of capacity is a maximum, then the highest rf power output possible for a given maximum allowable voltage at the minimum gap can be attained. This rf power output is then coupled to the generator load through a coupling condenser that prevents suppression of the dc charging potential by conduction through the load. Optimized circuit values produce phase shifts in the rf output voltage that allow higher power output to occur at the same voltage limit at the minimum gap position.

Open arthrolysis for elbow stiffness increases carrying angle but has no impact on functional recovery.

PubMed

Fan, Dapeng; Wang, Wei; Hildebrand, Kevin A; Fan, Cun-Yi

2016-09-09

With the exception of normal anatomic changes in the medial collateral ligament and radial head, other factors related to carrying angle changes have not been systematically studied. We reviewed patients who underwent open arthrolysis of the elbow, and evaluated if open arthrolysis could change carrying angle. We then identified factors associated with carrying angle changes. Fifty patients with a minimum of 24 months of follow-up after open arthrolysis were evaluated retrospectively. Preoperative and postoperative carrying angles were compared. The carrying angles of 36 elbows in 36 patients were unchanged after surgery (Group A), while the carrying angles of 14 elbows in 14 patients increased postoperatively (Group B). In Group A, mean postoperative extension and flexion were 7° (range 0-24°) and 125° (range 10-135°) respectively, while mean postoperative pronation and supination were 60° (range 50-80°) and 65° (range 30-85°), respectively. In Group B, mean postoperative extension and flexion were 25° (range 0-40°) and 128° (range 60-138°), while mean postoperative pronation and supination were 65° (range 45-85°) and 60° (range 45-75°), respectively. No significant difference in range of motion and Mayo Elbow Performance Score was observed between the two groups. During open arthrolysis, humeral trochlea debridement and techniques for improving forearm rotation could increase carrying angle. However, this had no impact on elbow functional recovery.

Language (In)competency, Communication Strategies, and the Development of an International Academic Teacher Identity: Becoming an Audible Minority

ERIC Educational Resources Information Center

McAllum, Kirstie

2017-01-01

Despite universities' enthusiasm for internationalization, international academic mobility requires considerable institutional and cultural adjustment in terms of teaching and supervision styles, research expectations, and departmental relationships. Although language competency underpins these practices, research on international academics has…

NOAA Weather Radio

Science.gov Websites

Information Reception Problems NWR Alarms Automated Voices FIPS Codes NWR - Special Needs SAME USING SAME SAME does not make an audible beep. However, it will display the words "CHECK RECEPTION" until it Reception Problems General Information NWR Alarms FIPS Codes Automated Voices Spanish Voices Public

46 CFR 95.15-30 - Alarms.

Code of Federal Regulations, 2012 CFR

2012-10-01

... automatically and audibly for at least 20 seconds before carbon dioxide is discharged into the space; (2) Be..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CARGO AND MISCELLANEOUS VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 95.15-30 Alarms. (a) A protected space must be fitted with an...

Chicanos y Chicanas Prominentes.

ERIC Educational Resources Information Center

Wood, Theodore E. B.

A sequel to "A Portfolio of Outstanding Americans of Mexican Descent", this portfolio contains 24 portraits and biographical sketches in both English and Spanish of Mexican American personalities who have become familiar as emergent figures in various sectors of public life. Featured are several women who have made themselves audible as…

46 CFR 154.1340 - Temperature measuring devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Each device must actuate an audible and visual alarm at the cargo control station and a remote group... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment... cargo control station. (c) Except for independent tanks type C, each cargo containment system for a...

46 CFR 154.1340 - Temperature measuring devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Each device must actuate an audible and visual alarm at the cargo control station and a remote group... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment... cargo control station. (c) Except for independent tanks type C, each cargo containment system for a...

46 CFR 154.1340 - Temperature measuring devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Each device must actuate an audible and visual alarm at the cargo control station and a remote group... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment... cargo control station. (c) Except for independent tanks type C, each cargo containment system for a...

46 CFR 154.1340 - Temperature measuring devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Each device must actuate an audible and visual alarm at the cargo control station and a remote group... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment... cargo control station. (c) Except for independent tanks type C, each cargo containment system for a...

46 CFR 154.1340 - Temperature measuring devices.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Each device must actuate an audible and visual alarm at the cargo control station and a remote group... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment... cargo control station. (c) Except for independent tanks type C, each cargo containment system for a...

16 CFR 1210.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... which this regulation applies. (d) Novelty lighter means a lighter that has entertaining audio or visual effects, or that depicts (logos, decals, art work, etc.) or resembles in physical form or function... produce a flame; and produces an audible or visual signal that will be clearly discernible when the...

30 CFR 57.14214 - Train warnings.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Train warnings. 57.14214 Section 57.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Equipment Safety Practices and Operational Procedures § 57.14214 Train warnings. A warning that is audible...

30 CFR 56.14214 - Train warnings.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Train warnings. 56.14214 Section 56.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Safety Practices and Operational Procedures § 56.14214 Train warnings. A warning that is audible above...

30 CFR 56.14214 - Train warnings.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Train warnings. 56.14214 Section 56.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Safety Practices and Operational Procedures § 56.14214 Train warnings. A warning that is audible above...

30 CFR 56.14214 - Train warnings.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Train warnings. 56.14214 Section 56.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Safety Practices and Operational Procedures § 56.14214 Train warnings. A warning that is audible above...

30 CFR 56.14214 - Train warnings.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Train warnings. 56.14214 Section 56.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Safety Practices and Operational Procedures § 56.14214 Train warnings. A warning that is audible above...

30 CFR 56.14214 - Train warnings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Train warnings. 56.14214 Section 56.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Safety Practices and Operational Procedures § 56.14214 Train warnings. A warning that is audible above...

30 CFR 57.14214 - Train warnings.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Train warnings. 57.14214 Section 57.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Equipment Safety Practices and Operational Procedures § 57.14214 Train warnings. A warning that is audible...

30 CFR 57.14214 - Train warnings.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Train warnings. 57.14214 Section 57.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Equipment Safety Practices and Operational Procedures § 57.14214 Train warnings. A warning that is audible...

30 CFR 57.14214 - Train warnings.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Train warnings. 57.14214 Section 57.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Equipment Safety Practices and Operational Procedures § 57.14214 Train warnings. A warning that is audible...

30 CFR 57.14214 - Train warnings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Train warnings. 57.14214 Section 57.14214 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Equipment Safety Practices and Operational Procedures § 57.14214 Train warnings. A warning that is audible...

30 CFR 18.20 - Quality of material, workmanship, and design.

Code of Federal Regulations, 2011 CFR

2011-07-01

... TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES... facilitate inspection and maintenance. (b) MSHA will test only electrical equipment that in the opinion of... shall be accessible for field inspection, where practicable. (e) An audible warning device shall be...

30 CFR 18.20 - Quality of material, workmanship, and design.

Code of Federal Regulations, 2010 CFR

2010-07-01

... TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES... facilitate inspection and maintenance. (b) MSHA will test only electrical equipment that in the opinion of... shall be accessible for field inspection, where practicable. (e) An audible warning device shall be...

Quieter Cars and the Safety of Blind Pedestrians, Phase 2 : Development of Potential Specifications for Vehicle Countermeasure Sounds.

DOT National Transportation Integrated Search

2011-10-01

This project performed research to support the development of potential specifications for vehicle : sounds, (i.e., audible countermeasures) to be used in vehicles while operating in electric mode in specific low speed : conditions. The purpose of th...

CAVITATION SOUNDS DURING CERVICOTHORACIC SPINAL MANIPULATION

PubMed Central

Mourad, Firas; Zingoni, Andrea; Iorio, Raffaele; Perreault, Thomas; Zacharko, Noah; de las Peñas, César Fernández; Butts, Raymond; Cleland, Joshua A.

2017-01-01

Background No study has previously investigated the side, duration or number of audible cavitation sounds during high-velocity low-amplitude (HVLA) thrust manipulation to the cervicothoracic spine. Purpose The primary purpose was to determine which side of the spine cavitates during cervicothoracic junction (CTJ) HVLA thrust manipulation. Secondary aims were to calculate the average number of cavitations, the duration of cervicothoracic thrust manipulation, and the duration of a single cavitation. Study Design Quasi-experimental study Methods Thirty-two patients with upper trapezius myalgia received two cervicothoracic HVLA thrust manipulations targeting the right and left T1-2 articulation, respectively. Two high sampling rate accelerometers were secured bilaterally 25 mm lateral to midline of the T1-2 interspace. For each manipulation, two audio signals were extracted using Short-Time Fourier Transformation (STFT) and singularly processed via spectrogram calculation in order to evaluate the frequency content and number of instantaneous energy bursts of both signals over time for each side of the CTJ. Result Unilateral cavitation sounds were detected in 53 (91.4%) of 58 cervicothoracic HVLA thrust manipulations and bilateral cavitation sounds were detected in just five (8.6%) of the 58 thrust manipulations; that is, cavitation was significantly (p<0.001) more likely to occur unilaterally than bilaterally. In addition, cavitation was significantly (p<0.0001) more likely to occur on the side contralateral to the clinician's short-lever applicator. The mean number of audible cavitations per manipulation was 4.35 (95% CI 2.88, 5.76). The mean duration of a single manipulation was 60.77 ms (95% CI 28.25, 97.42) and the mean duration of a single audible cavitation was 4.13 ms (95% CI 0.82, 7.46). In addition to single-peak and multi-peak energy bursts, spectrogram analysis also demonstrated high frequency sounds, low frequency sounds, and sounds of multiple frequencies for all 58 manipulations. Discussion Cavitation was significantly more likely to occur unilaterally, and on the side contralateral to the short-lever applicator contact, during cervicothoracic HVLA thrust manipulation. Clinicians should expect multiple cavitation sounds when performing HVLA thrust manipulation to the CTJ. Due to the presence of multi-peak energy bursts and sounds of multiple frequencies, the cavitation hypothesis (i.e. intra-articular gas bubble collapse) alone appears unable to explain all of the audible sounds during HVLA thrust manipulation, and the possibility remains that several phenomena may be occurring simultaneously. Level of Evidence 2b PMID:28900571

A Missing Puzzle Piece in Murray's Law: the Optimal Angle of Junctions

NASA Astrophysics Data System (ADS)

Wang, Ruo-Qian; Taylor, Katherine; Winter, Amos G.; Global Engineering; Research Lab Team

2014-11-01

Branching flows are common in biological systems, such as the circulatory and respiratory systems of animals. The optimal radii of parent and daughter branches can be explained with Murray's law, which dictates that the sum of metabolic and pumping costs is minimized. Murray's Law can be used to determine the diameter of cascading channels but misses an important parameter: the angles of the branches. Past hydraulic studies have investigated the angle effect, but have not focused on whether this geometry follows Murray's Law; while a simple network optimization is able to show that at low Reynolds numbers a branch with a parent channel connecting to n equally distant channels obeying Murray's Law has a minimum total head loss with a branching angle θ, such that cos θ =n-2/3 , but it's not valid for high Reynolds number flows, which may experience separation and turbulence at the branches. The present study is focused on determining the optimal branch angle that complies with Murray's Law for moderate Reynolds numbers. Computational studies using Open FOAM and experiments using 3D printed branched channels will be presented. These results will be used to quantify the effect of Reynolds number on optimal branch geometry.

Influence of Joint Angle on EMG-Torque Model During Constant-Posture, Torque-Varying Contractions.

PubMed

Liu, Pu; Liu, Lukai; Clancy, Edward A

2015-11-01

Relating the electromyogram (EMG) to joint torque is useful in various application areas, including prosthesis control, ergonomics and clinical biomechanics. Limited study has related EMG to torque across varied joint angles, particularly when subjects performed force-varying contractions or when optimized modeling methods were utilized. We related the biceps-triceps surface EMG of 22 subjects to elbow torque at six joint angles (spanning 60° to 135°) during constant-posture, torque-varying contractions. Three nonlinear EMG σ -torque models, advanced EMG amplitude (EMG σ ) estimation processors (i.e., whitened, multiple-channel) and the duration of data used to train models were investigated. When EMG-torque models were formed separately for each of the six distinct joint angles, a minimum "gold standard" error of 4.01±1.2% MVC(F90) resulted (i.e., error relative to maximum voluntary contraction at 90° flexion). This model structure, however, did not directly facilitate interpolation across angles. The best model which did so achieved a statistically equivalent error of 4.06±1.2% MVC(F90). Results demonstrated that advanced EMG σ processors lead to improved joint torque estimation as do longer model training durations.

Beam angle selection incorporation of anatomical heterogeneities for pencil beam scanning charged-particle therapy

NASA Astrophysics Data System (ADS)

Toramatsu, Chie; Inaniwa, Taku

2016-12-01

In charged particle therapy with pencil beam scanning (PBS), localization of the dose in the Bragg peak makes dose distributions sensitive to lateral tissue heterogeneities. The sensitivity of a PBS plan to lateral tissue heterogeneities can be reduced by selecting appropriate beam angles. The purpose of this study is to develop a fast and accurate method of beam angle selection for PBS. The lateral tissue heterogeneity surrounding the path of the pencil beams at a given angle was quantified with the heterogeneity number representing the variation of the Bragg peak depth across the cross section of the beams using the stopping power ratio of body tissues with respect to water. To shorten the computation time, one-dimensional dose optimization was conducted along the central axis of the pencil beams as they were directed by the scanning magnets. The heterogeneity numbers were derived for all possible beam angles for treatment. The angles leading to the minimum mean heterogeneity number were selected as the optimal beam angle. Three clinical cases of head and neck cancer were used to evaluate the developed method. Dose distributions and their robustness to setup and range errors were evaluated for all tested angles, and their relation to the heterogeneity numbers was investigated. The mean heterogeneity number varied from 1.2 mm-10.6 mm in the evaluated cases. By selecting a field with a low mean heterogeneity number, target dose coverage and robustness against setup and range errors were improved. The developed method is simple, fast, accurate and applicable for beam angle selection in charged particle therapy with PBS.

Optical parameters of TN display with dichroic dye

NASA Astrophysics Data System (ADS)

Olifierczuk, Marek; Zielinski, Jerzy; Perkowski, Pawel

2000-05-01

The present work contain the studies on optical parameters (contrast ratio, viewing angle, birefringence and brightness) of twisted nematic display with black dichroic dye which is designed for an application in large-area information and advertising systems. The numerical optimization of display with a dye has been done. The absorption characteristic of the dye has been obtained. Birefringence of doped mixtures (Delta) n has been measured. The contrast ratio of doped mixtures has been measured in wide temperature range from -25 degree(s)C to +70 degree(s)C. The angle characteristics of contrast ratio for +20 degree(s)C have been obtained. In the work the detailed results describing the effect of a dye on temperature dependence of birefringence and contrast ratio, moreover, the effect of dye on the viewing angle for the first and second transmission minimum will be presented. Additionally, the dielectric characteristics of different mixtures will be shown.

Geostationary Coastal and Air Pollution Events (GeoCAPE) Wide Angle Spectrometer (WAS)

NASA Technical Reports Server (NTRS)

Kotecki, Carl; Chu, Martha; Mannino, Antonio; Marx, Catherine Trout; Bowers, Gregory A.; Bolognese, Jeffrey A.; Matson, Elizabeth A.; McBirney, Thomas R.; Earle, Cleland P.; Choi, Michael K.;

Moiré-reduction method for slanted-lenticular-based quasi-three-dimensional displays

NASA Astrophysics Data System (ADS)

Zhuang, Zhenfeng; Surman, Phil; Zhang, Lei; Rawat, Rahul; Wang, Shizheng; Zheng, Yuanjin; Sun, Xiao Wei

2016-12-01

In this paper we present a method for determining the preferred slanted angle for a lenticular film that minimizes moiré patterns in quasi-three-dimensional (Q3D) displays. We evaluate the preferred slanted angles of the lenticular film for the stripe-type sub-pixel structure liquid crystal display (LCD) panel. Additionally, the sub-pixels mapping algorithm of the specific angle is proposed to assign the images to either the right or left eye channel. A Q3D display prototype is built. Compared with the conventional SLF, this newly implemented Q3D display can not only eliminate moiré patterns but also provide 3D images in both portrait and landscape orientations. It is demonstrated that the developed slanted lenticular film (SLF) provides satisfactory 3D images by employing a compact structure, minimum moiré patterns and stabilized 3D contrast.

New observations of the low energy proton inner belt

NASA Astrophysics Data System (ADS)

Guild, T. B.; Mazur, J. E.; Looper, M. D.; Blake, J. B.

2013-12-01

We present preliminary results of the trapped low energy (6-32 MeV) proton population in the inner radiation belt (L>1.8) from May, 2008 through present. These observations were made by the High Linear Energy Transfer (HiLET) proton telescope, part of the TWIN-ES instrument suite on the TWINS-2 spacecraft. This collimated telescope measures pitch-angle-resolved proton fluxes as it rises through the inner radiation belt twice per day. We present pitch angle distributions of low energy protons as a function of L, and show how the flux and pitch angle distributions change from the deep solar minimum of 2009 through the rising phase of solar cycle 24. Particular emphasis will be given to inner belt dynamics throughout this interval, both gradual and abrupt, and a discussion of the candidate processes responsible for these changes will be given.

Calibration of Gimbaled Platforms: The Solar Dynamics Observatory High Gain Antennas

NASA Technical Reports Server (NTRS)

Hashmall, Joseph A.

2006-01-01

Simple parameterization of gimbaled platform pointing produces a complete set of 13 calibration parameters-9 misalignment angles, 2 scale factors and 2 biases. By modifying the parameter representation, redundancy can be eliminated and a minimum set of 9 independent parameters defined. These consist of 5 misalignment angles, 2 scale factors, and 2 biases. Of these, only 4 misalignment angles and 2 biases are significant for the Solar Dynamics Observatory (SDO) High Gain Antennas (HGAs). An algorithm to determine these parameters after launch has been developed and tested with simulated SDO data. The algorithm consists of a direct minimization of the root-sum-square of the differences between expected power and measured power. The results show that sufficient parameter accuracy can be attained even when time-dependent thermal distortions are present, if measurements from a pattern of intentional offset pointing positions is included.

Wave-driven butterfly distribution of Van Allen belt relativistic electrons.

PubMed

Xiao, Fuliang; Yang, Chang; Su, Zhenpeng; Zhou, Qinghua; He, Zhaoguo; He, Yihua; Baker, D N; Spence, H E; Funsten, H O; Blake, J B

2015-10-05

Van Allen radiation belts consist of relativistic electrons trapped by Earth's magnetic field. Trapped electrons often drift azimuthally around Earth and display a butterfly pitch angle distribution of a minimum at 90° further out than geostationary orbit. This is usually attributed to drift shell splitting resulting from day-night asymmetry in Earth's magnetic field. However, direct observation of a butterfly distribution well inside of geostationary orbit and the origin of this phenomenon have not been provided so far. Here we report high-resolution observation that a unusual butterfly pitch angle distribution of relativistic electrons occurred within 5 Earth radii during the 28 June 2013 geomagnetic storm. Simulation results show that combined acceleration by chorus and magnetosonic waves can successfully explain the electron flux evolution both in the energy and butterfly pitch angle distribution. The current provides a great support for the mechanism of wave-driven butterfly distribution of relativistic electrons.

Energy Minimization of Discrete Protein Titration State Models Using Graph Theory.

PubMed

Purvine, Emilie; Monson, Kyle; Jurrus, Elizabeth; Star, Keith; Baker, Nathan A

2016-08-25

There are several applications in computational biophysics that require the optimization of discrete interacting states, for example, amino acid titration states, ligand oxidation states, or discrete rotamer angles. Such optimization can be very time-consuming as it scales exponentially in the number of sites to be optimized. In this paper, we describe a new polynomial time algorithm for optimization of discrete states in macromolecular systems. This algorithm was adapted from image processing and uses techniques from discrete mathematics and graph theory to restate the optimization problem in terms of "maximum flow-minimum cut" graph analysis. The interaction energy graph, a graph in which vertices (amino acids) and edges (interactions) are weighted with their respective energies, is transformed into a flow network in which the value of the minimum cut in the network equals the minimum free energy of the protein and the cut itself encodes the state that achieves the minimum free energy. Because of its deterministic nature and polynomial time performance, this algorithm has the potential to allow for the ionization state of larger proteins to be discovered.

Energy Minimization of Discrete Protein Titration State Models Using Graph Theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Purvine, Emilie AH; Monson, Kyle E.; Jurrus, Elizabeth R.

There are several applications in computational biophysics which require the optimization of discrete interacting states; e.g., amino acid titration states, ligand oxidation states, or discrete rotamer angles. Such optimization can be very time-consuming as it scales exponentially in the number of sites to be optimized. In this paper, we describe a new polynomial-time algorithm for optimization of discrete states in macromolecular systems. This algorithm was adapted from image processing and uses techniques from discrete mathematics and graph theory to restate the optimization problem in terms of maximum flow-minimum cut graph analysis. The interaction energy graph, a graph in which verticesmore » (amino acids) and edges (interactions) are weighted with their respective energies, is transformed into a flow network in which the value of the minimum cut in the network equals the minimum free energy of the protein, and the cut itself encodes the state that achieves the minimum free energy. Because of its deterministic nature and polynomial-time performance, this algorithm has the potential to allow for the ionization state of larger proteins to be discovered.« less

Energy Minimization of Discrete Protein Titration State Models Using Graph Theory

PubMed Central

Purvine, Emilie; Monson, Kyle; Jurrus, Elizabeth; Star, Keith; Baker, Nathan A.

2016-01-01

There are several applications in computational biophysics which require the optimization of discrete interacting states; e.g., amino acid titration states, ligand oxidation states, or discrete rotamer angles. Such optimization can be very time-consuming as it scales exponentially in the number of sites to be optimized. In this paper, we describe a new polynomial-time algorithm for optimization of discrete states in macromolecular systems. This algorithm was adapted from image processing and uses techniques from discrete mathematics and graph theory to restate the optimization problem in terms of “maximum flow-minimum cut” graph analysis. The interaction energy graph, a graph in which vertices (amino acids) and edges (interactions) are weighted with their respective energies, is transformed into a flow network in which the value of the minimum cut in the network equals the minimum free energy of the protein, and the cut itself encodes the state that achieves the minimum free energy. Because of its deterministic nature and polynomial-time performance, this algorithm has the potential to allow for the ionization state of larger proteins to be discovered. PMID:27089174

46 CFR 154.1365 - Audible and visual alarms.

Code of Federal Regulations, 2010 CFR

2010-10-01

... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment... it to be turned off after sounding. For remote group alarms this arrangement must not interrupt the..., except for remote group alarms, the location of each fault that actuates it. (d) Each vessel must have...

30 CFR 57.14132 - Horns and backup alarms for surface equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... NONMETAL MINES Machinery and Equipment Safety Devices and Maintenance Requirements § 57.14132 Horns and backup alarms for surface equipment. (a) Manually-operated horns or other audible warning devices provided on self-propelled mobile equipment as a safety device shall be maintained in a functional...

AFB's Computerized Travel Aid: Two Years of Research and Development.

ERIC Educational Resources Information Center

Uslan, Mark M.; And Others

1983-01-01

Progress on the computerized travel aid, an electronic device, using elements of the Polaroid Sonar Camera and a microprocessor, for visually handicapped persons is reviewed, and research on the effectiveness of various models noted. Recommended modifications touch on aspects of mounting, beam shape, and audible outputs. (CL)

30 CFR 75.344 - Compressors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... air course or to the surface and equipped with sensors to monitor for heat and for carbon monoxide or smoke. The sensors shall deenergize power to the compressor, activate a visual and audible alarm located... every 31 days, sensors installed to monitor for carbon monoxide shall be calibrated with a known...

77 FR 56265 - Proposed Information Collection Submitted to the Office of Management and Budget (OMB); Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-12

... the second experiment will evaluate the lack of effectiveness in current audible warnings designed to...: Title: Recruitment of human subjects for observational experiments regarding keyless ignition controls... motor vehicle safety standards (FMVSSs). Human factors observational experiments are proposed to support...

The Sounds of Science

ERIC Educational Resources Information Center

Grant, Julian

2017-01-01

In this article, Julian Grant, a Prep VI class teacher at Bridgewater School, Worsley, Manchester, explores the cross-curricular nature of language in scientific recording and how children can waken an audible science world with words. The ideas that came from what started as an applied vocabulary exercise demonstrated just how many…

30 CFR 75.344 - Compressors.

Code of Federal Regulations, 2011 CFR

2011-07-01

... air course or to the surface and equipped with sensors to monitor for heat and for carbon monoxide or smoke. The sensors shall deenergize power to the compressor, activate a visual and audible alarm located... every 31 days, sensors installed to monitor for carbon monoxide shall be calibrated with a known...

30 CFR 75.344 - Compressors.

Code of Federal Regulations, 2013 CFR

2013-07-01

... air course or to the surface and equipped with sensors to monitor for heat and for carbon monoxide or smoke. The sensors shall deenergize power to the compressor, activate a visual and audible alarm located... every 31 days, sensors installed to monitor for carbon monoxide shall be calibrated with a known...

30 CFR 75.344 - Compressors.

Code of Federal Regulations, 2014 CFR

2014-07-01

... air course or to the surface and equipped with sensors to monitor for heat and for carbon monoxide or smoke. The sensors shall deenergize power to the compressor, activate a visual and audible alarm located... every 31 days, sensors installed to monitor for carbon monoxide shall be calibrated with a known...

30 CFR 75.344 - Compressors.

Code of Federal Regulations, 2012 CFR

2012-07-01

... air course or to the surface and equipped with sensors to monitor for heat and for carbon monoxide or smoke. The sensors shall deenergize power to the compressor, activate a visual and audible alarm located... every 31 days, sensors installed to monitor for carbon monoxide shall be calibrated with a known...

46 CFR 95.15-30 - Alarms.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Dioxide Extinguishing Systems, Details § 95.15-30 Alarms. (a) Spaces which are protected by a carbon... audible alarm in such spaces which will be automatically sounded when the carbon dioxide is admitted to... sound during the 20 second delay period prior to the discharge of carbon dioxide into the space, and the...

77 FR 69923 - Petition for Waiver of Compliance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-21

... businesses, while maintaining the safety of an audible warning by ringing the bell. A copy of the petition, as well as any written communications concerning the petition, is available for review online at www... following methods: Web site: http://www.regulations.gov/ . Follow the online instructions for submitting...

30 CFR 250.1004 - Safety equipment requirements for DOI pipelines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Pipelines and Pipeline Rights-of... a flow safety valve (FSV). (ii) For sulphur operations, incoming pipelines delivering gas to the power plant platform may be equipped with high- and low-pressure sensors (PSHL), which activate audible...

30 CFR 250.1004 - Safety equipment requirements for DOI pipelines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL... operations, incoming pipelines delivering gas to the power plant platform may be equipped with high- and low-pressure sensors (PSHL), which activate audible and visual alarms in lieu of requirements in paragraph (b...

46 CFR 28.320 - Fixed gas fire extinguishing systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... only in a normally unoccupied machinery space, paint locker, or space containing flammable liquid... protect more than one space. The quantity of extinguishing agent must be at least sufficient for the... to indicate the discharge of the extinguishing agent; (ii) An audible alarm to sound upon discharge...

46 CFR 28.320 - Fixed gas fire extinguishing systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... only in a normally unoccupied machinery space, paint locker, or space containing flammable liquid... protect more than one space. The quantity of extinguishing agent must be at least sufficient for the... to indicate the discharge of the extinguishing agent; (ii) An audible alarm to sound upon discharge...

46 CFR 28.320 - Fixed gas fire extinguishing systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... only in a normally unoccupied machinery space, paint locker, or space containing flammable liquid... protect more than one space. The quantity of extinguishing agent must be at least sufficient for the... to indicate the discharge of the extinguishing agent; (ii) An audible alarm to sound upon discharge...

16 CFR 1500.17 - Banned hazardous substances.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (including but not limited to cherry bombs, M-80 salutes, silver salutes, and other large firecrackers, aerial bombs, and other fireworks designed to produce audible effects, and including kits and components... rocket), aerial bombs, and devices that may be confused with candy or other foods, such as “dragon eggs...

46 CFR 62.25-20 - Instrumentation, alarms, and centralized stations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ENGINEERING VITAL SYSTEM AUTOMATION General Requirements for All Automated Vital Systems § 62.25-20... there is no off position. (5) Automation alarms must be separate and independent of the following: (i... with a means to test audible and visual annunciators; (iv) Provide for normal equipment starting and...

Acoustics in Physical Education Settings: The Learning Roadblock

ERIC Educational Resources Information Center

Ryan, Stu; Mendel, Lisa Lucks

2010-01-01

Background: The audibility of teachers and peers is an essential factor in determining the academic performance of school children. However, acoustic conditions in most classrooms are less than optimal and have been viewed as "hostile listening environments" that undermine the learning of children in school. While research has shown that…

46 CFR 184.610 - Public address systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... public address system must be a fixed installation and be audible during normal operating conditions... system operable from the operating station. (d) On a vessel of not more than 19.8 meters (65 feet) in... passengers, a public address system is not required if a public announcement made from operating station...

33 CFR 146.105 - General alarm system.

Code of Federal Regulations, 2010 CFR

2010-07-01

... manned facility must have a general alarm system. When operated, this system shall be audible in all... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false General alarm system. 146.105 Section 146.105 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED...

46 CFR 154.1335 - Pressure and vacuum protection.

Code of Federal Regulations, 2012 CFR

2012-10-01

... audible and visual alarm at the cargo control station, and a remote group alarm in the wheelhouse. (c) If... SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and...) Has remote readouts at the cargo control station. (2) If vacuum protection is required under § 154.804...

46 CFR 154.1335 - Pressure and vacuum protection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... audible and visual alarm at the cargo control station, and a remote group alarm in the wheelhouse. (c) If... SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and...) Has remote readouts at the cargo control station. (2) If vacuum protection is required under § 154.804...

46 CFR 154.1335 - Pressure and vacuum protection.

Code of Federal Regulations, 2013 CFR

2013-10-01

... audible and visual alarm at the cargo control station, and a remote group alarm in the wheelhouse. (c) If... SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and...) Has remote readouts at the cargo control station. (2) If vacuum protection is required under § 154.804...

46 CFR 154.1335 - Pressure and vacuum protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... audible and visual alarm at the cargo control station, and a remote group alarm in the wheelhouse. (c) If... SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and...) Has remote readouts at the cargo control station. (2) If vacuum protection is required under § 154.804...

46 CFR 63.25-7 - Exhaust gas boilers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... results in inadequate heat transfer, a high temperature alarm or low flow alarm must be activated. An... insufficient to ensure proper heat transfer. Additionally, an audible alarm must automatically sound, and a... water level, the control system must supply the feed water at a rate sufficient to ensure proper heat...

46 CFR 63.25-7 - Exhaust gas boilers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... results in inadequate heat transfer, a high temperature alarm or low flow alarm must be activated. An... insufficient to ensure proper heat transfer. Additionally, an audible alarm must automatically sound, and a... water level, the control system must supply the feed water at a rate sufficient to ensure proper heat...

30 CFR 57.14200 - Warnings prior to starting or moving equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Warnings prior to starting or moving equipment... NONMETAL MINES Machinery and Equipment Safety Practices and Operational Procedures § 57.14200 Warnings... equipment, equipment operators shall sound a warning that is audible above the surrounding noise level or...

30 CFR 57.14200 - Warnings prior to starting or moving equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Warnings prior to starting or moving equipment... NONMETAL MINES Machinery and Equipment Safety Practices and Operational Procedures § 57.14200 Warnings... equipment, equipment operators shall sound a warning that is audible above the surrounding noise level or...

30 CFR 27.23 - Automatic warning device.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Automatic warning device. 27.23 Section 27.23... Automatic warning device. (a) An automatic warning device shall be suitably constructed for incorporation in... automatic warning device shall include an alarm signal (audible or colored light), which shall be made to...

30 CFR 27.23 - Automatic warning device.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Automatic warning device. 27.23 Section 27.23... Automatic warning device. (a) An automatic warning device shall be suitably constructed for incorporation in... automatic warning device shall include an alarm signal (audible or colored light), which shall be made to...

30 CFR 27.23 - Automatic warning device.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Automatic warning device. 27.23 Section 27.23... Automatic warning device. (a) An automatic warning device shall be suitably constructed for incorporation in... automatic warning device shall include an alarm signal (audible or colored light), which shall be made to...

30 CFR 27.23 - Automatic warning device.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Automatic warning device. 27.23 Section 27.23... Automatic warning device. (a) An automatic warning device shall be suitably constructed for incorporation in... automatic warning device shall include an alarm signal (audible or colored light), which shall be made to...

Conceptual apparatus for detecting leaks of nonconductive liquids

NASA Technical Reports Server (NTRS)

Walsh, G. D.

1968-01-01

Apparatus detects leaks at joints in lines carrying electrically nonconductive liquids. The proposed apparatus could include a panel that would give a visual or audible indication of a leak /to permit manual shutdown/ and/or an electromechanical actuator that would automatically cut off the flow when a leak occurs.

How to Generate Chaos at Home.

ERIC Educational Resources Information Center

Smith, Douglas

1992-01-01

Describes an electronic circuit that can function as a prototype for chaotic systems. Specific applied voltages produce chaotic signals that can be viewed with an oscilloscope or be made audible with a home stereo system. Provides directions for assembly with typical costs, mathematical basis of chaos theory, and experimental extensions. (JJK)

Automatic patient respiration failure detection system with wireless transmission

NASA Technical Reports Server (NTRS)

Dimeff, J.; Pope, J. M.

1968-01-01

Automatic respiration failure detection system detects respiration failure in patients with a surgically implanted tracheostomy tube, and actuates an audible and/or visual alarm. The system incorporates a miniature radio transmitter so that the patient is unencumbered by wires yet can be monitored from a remote location.

Radioactive Decay: Audio Data Collection

ERIC Educational Resources Information Center

Struthers, Allan

2009-01-01

Many phenomena generate interesting audible time series. This data can be collected and processed using audio software. The free software package "Audacity" is used to demonstrate the process by recording, processing, and extracting click times from an inexpensive radiation detector. The high quality of the data is demonstrated with a simple…

In-vehicle evaluation of milled rumble strips at pre- and post-chip sealed maintenance periods : final report.

DOT National Transportation Integrated Search

2017-01-01

Driver fatigue and drowsiness can have a profound impact on safety. Centerline and shoulder rumble strips (RS) are popular countermeasures designed to produce audible and tactile warning when vehicles deviate from the travel lane onto the RS. This re...

46 CFR 130.460 - Placement of machinery alarms.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Placement of machinery alarms. 130.460 Section 130.460..., AND MISCELLANEOUS EQUIPMENT AND SYSTEMS Automation of Unattended Machinery Spaces § 130.460 Placement of machinery alarms. (a) Visible and audible alarms must be installed at the pilothouse to indicate...

46 CFR 130.460 - Placement of machinery alarms.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Placement of machinery alarms. 130.460 Section 130.460..., AND MISCELLANEOUS EQUIPMENT AND SYSTEMS Automation of Unattended Machinery Spaces § 130.460 Placement of machinery alarms. (a) Visible and audible alarms must be installed at the pilothouse to indicate...

46 CFR 130.460 - Placement of machinery alarms.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Placement of machinery alarms. 130.460 Section 130.460..., AND MISCELLANEOUS EQUIPMENT AND SYSTEMS Automation of Unattended Machinery Spaces § 130.460 Placement of machinery alarms. (a) Visible and audible alarms must be installed at the pilothouse to indicate...

46 CFR 130.460 - Placement of machinery alarms.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Placement of machinery alarms. 130.460 Section 130.460..., AND MISCELLANEOUS EQUIPMENT AND SYSTEMS Automation of Unattended Machinery Spaces § 130.460 Placement of machinery alarms. (a) Visible and audible alarms must be installed at the pilothouse to indicate...

Discrepancy in clinical versus radiological parameters describing deformity due to brace treatment for moderate idiopathic scoliosis.

PubMed

Kotwicki, Tomasz; Kinel, Edyta; Stryla, Wanda; Szulc, Andrzej

2007-12-03

The shape of the torso in patients with idiopathic scoliosis is considered to reflect the shape of the vertebral column, however the direct correlation between parameters describing clinical deformity and those characterizing radiological curvature was reported to be weak. It is not clear if the management proposed for scoliosis (physiotherapy, brace, surgery) affects equally the shape of the axial skeleton and the surface of the body. The aim of the study was to compare clinical deformity of (1) idiopathic scoliosis girls being under brace treatment for radiological curves of 25 to 40 degrees and (2) non treated scoliotic girls matched for age and Cobb angle. Cross-sectional study of 24 girls wearing the brace versus 26 girls without brace treatment, matched for age and Cobb angle. Patients wearing the brace for more than 6 months, when comparing to patients without brace, may present different external morphology of the trunk, in spite of having similar Cobb angle. Material. girls, idiopathic scoliosis, growing age (10-16 years), Cobb angle minimum 25 degrees , maximum 40 degrees . The braced group consisted of girls wearing a TLSO brace (Cheneau) for more than 6 months with minimum of 16 hours per day. The non-braced group consisted of girls first seen for their spinal deformity, previously not treated. The groups presented similar curve pattern. Methods. Scoliometer exam: angle of trunk rotation at three levels of the spine: upper thoracic, main thoracic, lumbar or thoracolumbar. The maximal angle was noted at each level and the sum of three levels was calculated. Posterior trunk symmetry index (POTSI) and Hump Sum were measured using surface topography. Cobb angle was 34.9 degrees +/- 4.8 degrees in braced and 32.7 degrees +/- 4.9 degrees in un-braced patients (difference not significant). The age was 14.1 +/- 1.6 years in braced patients and 13.1 +/- 1.9 years in un-braced group (p = 0.046). The value of angle of trunk rotation in the main curvature was 8.4 degrees +/- 2.7 degrees in braced and 11.4 degrees +/- 2.7 degrees in un-braced patients (difference extremely significant, p = 0.0003). The value of the sum of angles of trunk rotation at three levels of the trunk was 12.8 degrees +/- 4.6 degrees in braced and 16.5 degrees +/- 3.8 degrees in un-braced patients (difference very significant, p = 0.0038). The POTSI did not differ significantly between the groups (p = 0.78), the Hump Sum values were not quite different (p = 0.07). (1) Adolescent girls wearing the brace for idiopathic scoliosis of 25 to 40 degrees of Cobb angle, reveal smaller clinical rotational deformity of their back than non-treated girls having similar radiological deformity. (2) Evaluation of the results of treatment for idiopathic scoliosis should consider parameters describing both clinical and radiological deformity.

Multidimensional CAT Item Selection Methods for Domain Scores and Composite Scores with Item Exposure Control and Content Constraints

ERIC Educational Resources Information Center

Yao, Lihua

2014-01-01

The intent of this research was to find an item selection procedure in the multidimensional computer adaptive testing (CAT) framework that yielded higher precision for both the domain and composite abilities, had a higher usage of the item pool, and controlled the exposure rate. Five multidimensional CAT item selection procedures (minimum angle;…

46 CFR 178.330 - Simplified stability proof test (SST).

Code of Federal Regulations, 2011 CFR

2011-10-01

... limits of heel: (1) On a flush deck vessel, not more than one-half of the freeboard may be immersed. (2... is less, may be immersed. (7) In no case may the angle of heel exceed 14 degrees. (e) The limits of heel must be measured at: (1) The point of minimum freeboard; or (2) At a point three-quarters of the...

49 CFR 571.218 - Standard No. 218; Motorcycle helmets.

Code of Federal Regulations, 2013 CFR

2013-10-01

... provide peripheral vision clearance of at least 105° to each side of the mid-sagittal plane, when the... basic plane that are within the angles of peripheral vision (see Figure 3). S5.5 Projections. A helmet... including 70 percent for a minimum of 4 hours. (b) Low temperature. Expose to any temperature from 5 °F to...

49 CFR 571.218 - Standard No. 218; Motorcycle helmets.

Code of Federal Regulations, 2014 CFR

2014-10-01

... provide peripheral vision clearance of at least 105° to each side of the mid-sagittal plane, when the... basic plane that are within the angles of peripheral vision (see Figure 3). S5.5 Projections. A helmet... including 70 percent for a minimum of 4 hours. (b) Low temperature. Expose to any temperature from 5 °F to...

47 CFR 25.205 - Minimum angle of antenna elevation.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) of this section must still meet the effective isotropically radiated power (e.i.r.p.) and e.i.r.p. density towards the horizon limits contained in § 25.204(h) and (i). (c) VMESs making a special showing... limits contained in § 25.204(j). [70 FR 4784, Jan. 31, 2005, as amended at 74 FR 57099, Nov. 4, 2009] ...

The Effect of Nose Shape on the Drag of Bodies of Revolution at Zero Angle of Attack

NASA Technical Reports Server (NTRS)

Seiff, Alvin; Sandahl, Carl A.

1951-01-01

The subject of this paper is the drag of the nose section of bodies of revolution at zero angle of attack. The magnitude of the nose drag in relation to the total drag is very distinctly a function of the body design and the Mach number. It can range from a very small fraction of the total drag of the order of 10 percent to a very large fraction as high as 80 percent. The natural objective of nose design is to minimize the drag, but this objective is not always the primary one. Sometimes other factors overshadow the desire for minimum drag. The most conspicuous example of this is the proposal of guidance engineers that large-diameter spheres and other very blunt shapes be used at the nose tip. This paper will attempt to discuss both phases of the problem, noses for minimum drag and noses with very blunt tips. The state of the theory will also be reviewed and recent theoretical developments described, since the theory still remains a very valuable tool for assaying the effects of compromises in design and departure from shapes for which experimental data are available.

Energy management of three-dimensional minimum-time intercept. [for aircraft flight optimization

NASA Technical Reports Server (NTRS)

Kelley, H. J.; Cliff, E. M.; Visser, H. G.

1985-01-01

A real-time computer algorithm to control and optimize aircraft flight profiles is described and applied to a three-dimensional minimum-time intercept mission. The proposed scheme has roots in two well known techniques: singular perturbations and neighboring-optimal guidance. Use of singular-perturbation ideas is made in terms of the assumed trajectory-family structure. A heading/energy family of prestored point-mass-model state-Euler solutions is used as the baseline in this scheme. The next step is to generate a near-optimal guidance law that will transfer the aircraft to the vicinity of this reference family. The control commands fed to the autopilot (bank angle and load factor) consist of the reference controls plus correction terms which are linear combinations of the altitude and path-angle deviations from reference values, weighted by a set of precalculated gains. In this respect the proposed scheme resembles neighboring-optimal guidance. However, in contrast to the neighboring-optimal guidance scheme, the reference control and state variables as well as the feedback gains are stored as functions of energy and heading in the present approach. Some numerical results comparing open-loop optimal and approximate feedback solutions are presented.

Electrostatic Interactions Between Glycosaminoglycan Molecules

NASA Astrophysics Data System (ADS)

Song, Fan; Moyne, Christian; Bai, Yi-Long

2005-02-01

The electrostatic interactions between nearest-neighbouring chondroitin sulfate glycosaminoglycan (CS-GAG) molecular chains are obtained on the bottle brush conformation of proteoglycan aggrecan based on an asymptotic solution of the Poisson-Boltzmann equation the CS-GAGs satisfy under the physiological conditions of articular cartilage. The present results show that the interactions are associated intimately with the minimum separation distance and mutual angle between the molecular chains themselves. Further analysis indicates that the electrostatic interactions are not only expressed to be purely exponential in separation distance and decrease with the increasing mutual angle but also dependent sensitively on the saline concentration in the electrolyte solution within the tissue, which is in agreement with the existed relevant conclusions.

Chirp-Z analysis for sol-gel transition monitoring.

PubMed

Martinez, Loïc; Caplain, Emmanuel; Serfaty, Stéphane; Griesmar, Pascal; Gouedard, Gérard; Gindre, Marcel

2004-04-01

Gelation is a complex reaction that transforms a liquid medium into a solid one: the gel. In gel state, some gel materials (DMAP) have the singular property to ring in an audible frequency range when a pulse is applied. Before the gelation point, there is no transmission of slow waves observed; after the gelation point, the speed of sound in the gel rapidly increases from 0.1 to 10 m/s. The time evolution of the speed of sound can be measured, in frequency domain, by following the frequency spacing of the resonance peaks from the Synchronous Detection (SD) measurement method. Unfortunately, due to a constant frequency sampling rate, the relative error for low speeds (0.1 m/s) is 100%. In order to maintain a low constant relative error, in the whole speed time evolution range, Chirp-Z Transform (CZT) is used. This operation transforms a time variant signal to a time invariant one using only a time dependant stretching factor (S). In the frequency domain, the CZT enables us to stretch each collected spectrum from time signals. The blind identification of the S factor gives us the complete time evolution law of the speed of sound. Moreover, this method proves that the frequency bandwidth follows the same time law. These results point out that the minimum wavelength stays constant and that it only depends on the gel.

Drop impact on spherical soft surfaces

NASA Astrophysics Data System (ADS)

Chen, Simeng; Bertola, Volfango

2017-08-01

The impact of water drops on spherical soft surfaces is investigated experimentally through high-speed imaging. The effect of a convex compliant surface on the dynamics of impacting drops is relevant to various applications, such as 3D ink-jet printing, where drops of fresh material impact on partially cured soft substrates with arbitrary shape. Several quantities which characterize the morphology of impacting drops are measured through image-processing, including the maximum and minimum spreading angles, length of the wetted curve, and dynamic contact angle. In particular, the dynamic contact angle is measured using a novel digital image-processing scheme based on a goniometric mask, which does not require edge fitting. It is shown that the surface with a higher curvature enhances the retraction of the spreading drop; this effect may be due to the difference of energy dissipation induced by the curvature of the surface. In addition, the impact parameters (elastic modulus, diameter ratio, and Weber number) are observed to significantly affect the dynamic contact angle during impact. A quantitative estimation of the deformation energy shows that it is significantly smaller than viscous dissipation.

Electron pitch angle distributions throughout the magnetosphere as observed on Ogo 5.

NASA Technical Reports Server (NTRS)

West, H. I., Jr.; Buck, R. M.; Walton, J. R.

1973-01-01

A survey of the equatorial pitch angle distributions of energetic electrons is provided for all local times out to radial distances of 20 earth radii on the night side of the earth and to the magnetopause on the day side of the earth. In much of the inner magnetosphere and in the outer magnetosphere on the day side of the earth, the normal loss cone distribution prevails. The effects of drift shell splitting - i.e., the appearance of pitch angle distributions with minimums at 90 deg, called butterfly distributions - become apparent in the early afternoon magnetosphere at extended distances, and the distribution is observed in to 5.5 earth radii in the nighttime magnetosphere. Inside about 9 earth radii the pitch angle effects are quite energy-dependent. Beyond about 9 earth radii in the premidnight magnetosphere during quiet times the butterfly distribution is often observed. It is shown that these electrons cannot survive a drift to dawn without being considerably modified. The role of substorm activity in modifying these distributions is identified.

Unique features of laterally aligned GeSi nanowires self-assembled on the vicinal Si (001) surface misoriented toward the [100] direction

NASA Astrophysics Data System (ADS)

Zhou, Tong; Vastola, Guglielmo; Zhang, Yong-Wei; Ren, Qijun; Fan, Yongliang; Zhong, Zhenyang

2015-03-01

We demonstrate laterally aligned and catalyst-free GeSi nanowires (NWs) via self-assembly of Ge on miscut Si (001) substrates toward the [100] direction by an angle θ (θ < 11°). The NWs are bordered by (001) and (105) facets, which are thermodynamically stable. By tuning the miscut angle θ, the NW height can be easily modulated with a nearly constant width. The thickness of the wetting layer beneath the NWs also shows a peculiar behavior with a minimum at around 6°. An analytical model, considering the variation of both the surface energy and the strain energy of the epilayer on vicinal surfaces with the miscut angle and layer thickness, shows good overall agreement with the experimental results. It discloses that both the surface energy and stain energy of the epilayer on vicinal surfaces can be considerably affected in the same trend by the surface steps. Our results not only shed new light on the growth mechanism during heteroepitaxial growth, but also pave a prominent way to fabricate and meanwhile modulate laterally aligned and dislocation-free NWs.We demonstrate laterally aligned and catalyst-free GeSi nanowires (NWs) via self-assembly of Ge on miscut Si (001) substrates toward the [100] direction by an angle θ (θ < 11°). The NWs are bordered by (001) and (105) facets, which are thermodynamically stable. By tuning the miscut angle θ, the NW height can be easily modulated with a nearly constant width. The thickness of the wetting layer beneath the NWs also shows a peculiar behavior with a minimum at around 6°. An analytical model, considering the variation of both the surface energy and the strain energy of the epilayer on vicinal surfaces with the miscut angle and layer thickness, shows good overall agreement with the experimental results. It discloses that both the surface energy and stain energy of the epilayer on vicinal surfaces can be considerably affected in the same trend by the surface steps. Our results not only shed new light on the growth mechanism during heteroepitaxial growth, but also pave a prominent way to fabricate and meanwhile modulate laterally aligned and dislocation-free NWs. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr07433e

Effect of Multiangular Observations on Crop Chlorophyll Content Retrieval Using Field Top-Of Spectrometer Data

NASA Astrophysics Data System (ADS)

Jiao, Q.; Liu, L.; Zhang, B.

2017-12-01

Leaf chlorophyll content is an important indicator of crop growth condition that determines final crop yield. A lot of research on remote sensing of leaf chlorophyll content were based on reflectance data acquired from nadir direction. However, reflectance data at nadir may be affected by soil background. In fact, many satellite sensors with capability of chlorophyll retrieval, like the 68.5 degrees field-of-view MERIS, have produced large multiangular data. This study tries to assess the anisotropic effect on the retrieval of leaf chlorophyll content using field hyperspectral data of wheat canopy. The field multi-angle observation experiment of winter wheat was carried out in April 2017 in Xiaotangshan agriculture demonstration study site in Beijing. Field canopy spectra and leaf chlorophyll content of winter wheat were measured. The most used indices for chlorophyll content retrieval, such as CIred-edge, REP, MTCI, MCARI/OSAVI[705,750], TCARI/OSAVI[705,750], were calculated based on the filed multiangular reflectance. The ratio index TCARI/OSAVI owned the best results in estimating leaf chlorophyll content (R2 of 0.62) among all the selected indices, when using the top-of-canopy reflectance at nadir. The determination coefficient of the relationship of TCARI/OSAVI with chlorophyll content reached its peak (R2 of 0.70) at angle of 15 degrees, and the minimum R2 value of only 0.25 at angle of 60 degrees. The MTCI got the peak of determination coefficient (R2 of 0.63) at angle of 15 degrees and the minimum value (R2 of 0.57) for 60 degrees. Our results showed the MTCI could keep a more satisfactory correlation with leaf chlorophyll content of winter wheat, however the mean values of the MTCI basically decreased as the observation angle increases. This work shows the strong anisotropic effects of top-of-canopy reflectance which influences most of selected popular chlorophyll indices. If spectral index selection is proper, multiangular remote sensing could produce higher accuracy for leaf chlorophyll content retrieval than only using nadir observation. Multi-angular remote sensing has the potential of leaf chlorophyll content retrieval for diagnosis of crop nitrogen stress or water stress.

Angle of Attack Modulation for Mars Entry Terminal State Optimization

NASA Technical Reports Server (NTRS)

Lafleur, Jarret M.; Cerimele, Christopher J.

2009-01-01

From the perspective of atmospheric entry, descent, and landing (EDL), one of the most foreboding destinations in the solar system is Mars due in part to its exceedingly thin atmosphere. To benchmark best possible scenarios for evaluation of potential Mars EDL system designs, a study is conducted to optimize the entry-to-terminal-state portion of EDL for a variety of entry velocities and vehicle masses, focusing on the identification of potential benefits of enabling angle of attack modulation. The terminal state is envisioned as one appropriate for the initiation of terminal descent via parachute or other means. A particle swarm optimizer varies entry flight path angle, ten bank profile points, and ten angle of attack profile points to find maximum-final-altitude trajectories for a 10 30 m ellipsled at 180 different combinations of values for entry mass, entry velocity, terminal Mach number, and minimum allowable altitude. Parametric plots of maximum achievable altitude are shown, as are examples of optimized trajectories. It is shown that appreciable terminal state altitude gains (2.5-4.0 km) over pure bank angle control may be possible if angle of attack modulation is enabled for Mars entry vehicles. Gains of this magnitude could prove to be enabling for missions requiring high-altitude landing sites. Conclusions are also drawn regarding trends in the bank and angle of attack profiles that produce the optimal trajectories in this study, and directions for future work are identified.