Development and production of a flame retardant, general purpose, pressure sensitive adhesive tape

NASA Technical Reports Server (NTRS)

Monaghan, P. B.; Doggett, R. H.

1977-01-01

The specification results for the finished tape properties were as follows: (1) adhesive strength (180 deg peel) on aluminum from 107 to 143 grams per centimeter (0.6 to 0.8 pounds per inch); (2) adhesive strength (180 deg peel) on stainless steel from 71 to 107 grams per centimeter (0.4 to 0.6 pounds per inch); (3) unwind resistance of 536 to 714 grams per centimeter (3 to 4 pounds per inch); (4) tensile strength minimum of 7143 grams per centimeter (40 pounds per inch); (5) elongation from 5 to 10% at break; (6) tear strength, Elmendorf from 200 to 350 grams (0.44 to 0.77 pounds); and (7) tear strength, tongue from 363 to 408 grams (0.8 to 0.9) pounds).

Ultrashort pulse laser dicing of thin Si wafers: the influence of laser-induced periodic surface structures on the backside breaking strength

NASA Astrophysics Data System (ADS)

Domke, Matthias; Egle, Bernadette; Piredda, Giovanni; Stroj, Sandra; Fasching, Gernot; Bodea, Marius; Schwarz, Elisabeth

2016-11-01

High power electronic chips are usually fabricated on about 50 µm thin Si wafers to improve heat dissipation. At these chip thicknesses mechanical dicing becomes challenging. Chippings may occur at the cutting edges, which reduce the mechanical stability of the die. Thermal load changes could then lead to sudden chip failure. Ultrashort pulsed lasers are a promising tool to improve the cutting quality, because thermal side effects can be reduced to a minimum. However, laser-induced periodic surface structures occur at the sidewalls and at the trench bottom during scribing. The goal of this study was to investigate the influence of these periodic structures on the backside breaking strength of the die. An ultrafast laser with a pulse duration of 380 fs and a wavelength of 1040 nm was used to cut a wafer into single chips. The pulse energy and the number of scans was varied. The cuts in the wafer were investigated using transmitted light microscopy, the sidewalls of the cut chips were investigated using scanning electron and confocal microscopy, and the breaking strength was evaluated using the 3-point bending test. The results indicated that periodic holes with a distance of about 20-30 µm were formed at the bottom of the trench, if the number of scans was set too low to completely cut the wafer; the wafer was only perforated. Mechanical breaking of the bridges caused 5 µm deep kerfs in the sidewall. These kerfs reduced the breaking strength at the backside of the chip to about 300 MPa. As the number of scans was increased, the bridges were ablated and the wafer was cut completely. Periodic structures were observed on the sidewall; the roughness was below 1 µm. The surface roughness remained on a constant level even when the number of scans was doubled. However, the periodic structures on the sidewall seemed to vanish and the probability to remove local flaws increases with the number of scans. As a consequence, the breaking strength was increased to about 700 MPa.

Thermal and mechanical properties of reduced graphene oxide/polyurethane nanocomposite.

PubMed

Pokharel, Pashupati; Lee, Dai Soo

2014-08-01

Reduced graphene oxide (RGO) based polyurethane (PU) nanocomposites have been successfully prepared without using solvent by in-situ polymerization. RGO was derived from microwave (MW) irradiation of graphite oxide (GO) powder prepared by a modified Hummer's method. A minimum amount of poly(tetramethylene glycol) (PTMEG) was added during the dispersion of RGO in a solvent to stabilize the graphene sheets and to prevent RGO from the restacking after the removal of the solvent. After the reaction of RGO with 4,4'-diphenylmethane diisocyanate (MDI), we obtained the concentrate of RGO in MDI with a minimum amount of PTMEG. Our method facilitated the fine dispersion of RGO in PU elastomers and improved the interfacial strength between RGO and PU. With the incorporation of 2.0 wt% of RGO, the tensile strength and Young's modulus of the PU nanocomposites increased by 30% and 50%, respectively without sacrificing the elongation at break. It was found that the crystalline portion of hard segments of the PU was lowered by the RGO in the nanocomposites.

46 CFR 160.076-21 - Component materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... by § 160.076-25(d)(2)(iii). (c) The average grab breaking strength and tear strength of the inflation....076-25(d)(2)(ii), must be at least 90% of the grab breaking strength and tear strength determined from... breaking strength or tear strength may be more than 20% below the results obtained in approval testing. (d...

How Does Definition of Minimum Break Length Affect Objective Measures of Sitting Outcomes Among Office Workers?

PubMed

Kloster, Stine; Danquah, Ida Høgstedt; Holtermann, Andreas; Aadahl, Mette; Tolstrup, Janne Schurmann

2017-01-01

Harmful health effects associated with sedentary behavior may be attenuated by breaking up long periods of sitting by standing or walking. However, studies assess interruptions in sitting time differently, making comparisons between studies difficult. It has not previously been described how the definition of minimum break duration affects sitting outcomes. Therefore, the aim was to address how definitions of break length affect total sitting time, number of sit-to-stand transitions, prolonged sitting periods and time accumulated in prolonged sitting periods among office workers. Data were collected from 317 office workers. Thigh position was assessed with an ActiGraph GT3X+ fixed on the right thigh. Data were exported with varying bout length of breaks. Afterward, sitting outcomes were calculated for the respective break lengths. Absolute numbers of sit-to-stand transitions decreased, and number of prolonged sitting periods and total time accumulated in prolonged sitting periods increased, with increasing minimum break length. Total sitting time was not influenced by varying break length. The definition of minimum break length influenced the sitting outcomes with the exception of total sitting time. A standard definition of break length is needed for comparison and interpretation of studies in the evolving research field of sedentary behavior.

Tissue soldering with biodegradable polymer films: in-vitro investigation of hydration effects on weld strength

NASA Astrophysics Data System (ADS)

Sorg, Brian S.; Welch, Ashley J.

2001-05-01

Previous work demonstrated increased breaking strengths of tissue repaired with liquid albumin solder reinforced with a biodegradable polymer film compared to unreinforced control specimens. It was hypothesized that the breaking strength increase was due to reinforcement of the liquid solder cohesive strength. Immersion in a moist environment can decrease the adhesion of solder to tissue and negate any strength benefits gained from reinforcement. The purpose of this study was to determine if hydrated specimens repaired with reinforced solder would still be stronger than unreinforced controls. A 50%(w/v) bovine serum albumin solder with 0.5 mg/mL Indocyanine Green dye was used to repair an incision in bovine aorta. The solder was coagulated with 806-nm diode laser light. A poly(DL-lactic- co-glycolic acid) film was used to reinforce the solder (the controls had no reinforcement). The repaired tissues were immersed in phosphate buffered saline for time periods of 1 and 2 days. The breaking strengths of all of the hydrated specimens decreased compared to the acute breaking strengths. However, the reinforced specimens still had larger breaking strengths than the unreinforced controls. These results indicate that reinforcement of a liquid albumin solder may have the potential to improve the breaking strength in a clinical setting.

46 CFR 169.521 - Stowage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... vessel must— (i) Have a breaking strength of at least the breaking strength of the painter. (ii) If... attachment fitting, a means for attaching the painter must be provided by a wire or line that— (i) Encircles the body of the device; (ii) Will not slip off; (iii) Has a breaking strength that is at least the...

46 CFR 169.521 - Stowage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... vessel must— (i) Have a breaking strength of at least the breaking strength of the painter. (ii) If... attachment fitting, a means for attaching the painter must be provided by a wire or line that— (i) Encircles the body of the device; (ii) Will not slip off; (iii) Has a breaking strength that is at least the...

46 CFR 169.521 - Stowage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... vessel must— (i) Have a breaking strength of at least the breaking strength of the painter. (ii) If... attachment fitting, a means for attaching the painter must be provided by a wire or line that— (i) Encircles the body of the device; (ii) Will not slip off; (iii) Has a breaking strength that is at least the...

Predicting Tissue Breaking Strengths in the Epileptic Brain with T2 Relaxometry: Application of Pulsed Water Jet Dissection System for Epilepsy Surgery.

PubMed

Takahashi, Yoko; Iwasaki, Masaki; Nakagawa, Atsuhiro; Sato, Shiho; Nakasato, Nobukazu; Tominaga, Teiji

2017-11-01

Background  The piezo actuator-driven pulsed water jet (ADPJ) system is a novel surgical instrument that enables dissection of tissue without thermal damage. Using the ADPJ system in epilepsy surgery requires prediction of the tissue breaking strength of the epileptic brain. The aim of this study was to elucidate whether magnetic resonance imaging T2 relaxometry could predict the breaking strength. Methods  A total of 12 patients with drug-resistant temporal lobe epilepsy who received surgical treatment were included in the study. All the patients qualified for surgery after a comprehensive preoperative evaluation for the treatment of epilepsy. T2 relaxation time, breaking strength of the hippocampus, and an anterior temporal lobe specimen obtained from surgery with dissection depth determined by the ADPJ system were examined. Results  Preoperative T2 relaxation times of the anterior temporal lobe and hippocampus showed mild positive correlation with breaking strength (R 2  = 0.60). The hippocampus showed higher T2 relaxation time than the temporal lobe. Hippocampal sclerosis seemed to have higher breaking strength than other pathologies, suggesting the correlation depends on the anatomical location and histopathology. The dissection depth of the extirpated lesion was negatively correlated with the breaking strength at input voltages of 10 V (R 2  = - 0.34) and 20 V (R 2  = - 0.20). Conclusions  T2 relaxometry may be useful to predict tissue breaking strength in the epileptic brain that allows safe application of the ADPJ system in epilepsy surgery. Georg Thieme Verlag KG Stuttgart · New York.

46 CFR 180.137 - Stowage of life floats and buoyant apparatus.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Have a breaking strength of at least the breaking strength of the painter; (2) If synthetic, be of a... attachment fitting, a means for attaching the painter must be provided by a wire or line that: (1) Encircles the body of the device; (2) Will not slip off; (3) Has a breaking strength that is at least the...

46 CFR 180.137 - Stowage of life floats and buoyant apparatus.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Have a breaking strength of at least the breaking strength of the painter; (2) If synthetic, be of a... attachment fitting, a means for attaching the painter must be provided by a wire or line that: (1) Encircles the body of the device; (2) Will not slip off; (3) Has a breaking strength that is at least the...

46 CFR 180.137 - Stowage of life floats and buoyant apparatus.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Have a breaking strength of at least the breaking strength of the painter; (2) If synthetic, be of a... attachment fitting, a means for attaching the painter must be provided by a wire or line that: (1) Encircles the body of the device; (2) Will not slip off; (3) Has a breaking strength that is at least the...

Response of jammed packings to thermal fluctuations

NASA Astrophysics Data System (ADS)

Wu, Qikai; Bertrand, Thibault; Shattuck, Mark D.; O'Hern, Corey S.

2017-12-01

We focus on the response of mechanically stable (MS) packings of frictionless, bidisperse disks to thermal fluctuations, with the aim of quantifying how nonlinearities affect system properties at finite temperature. In contrast, numerous prior studies characterized the structural and mechanical properties of MS packings of frictionless spherical particles at zero temperature. Packings of disks with purely repulsive contact interactions possess two main types of nonlinearities, one from the form of the interaction potential (e.g., either linear or Hertzian spring interactions) and one from the breaking (or forming) of interparticle contacts. To identify the temperature regime at which the contact-breaking nonlinearities begin to contribute, we first calculated the minimum temperatures Tc b required to break a single contact in the MS packing for both single- and multiple-eigenmode perturbations of the T =0 MS packing. We find that the temperature required to break a single contact for equal velocity-amplitude perturbations involving all eigenmodes approaches the minimum value obtained for a perturbation in the direction connecting disk pairs with the smallest overlap. We then studied deviations in the constant volume specific heat C¯V and deviations of the average disk positions Δ r from their T =0 values in the temperature regime TC ¯V100 for linear spring interactions is independent of system size. This result emphasizes that contact-breaking nonlinearities are dominant over form nonlinearities in the low-temperature range Tc b

Evaluation of wound healing, antioxidant and antimicrobial efficacy of Jasminum auriculatum Vahl. leaves.

PubMed

Arun, Mittal; Satish, Sardana; Anima, Pandey

2016-01-01

To validate the ethno-therapeutic claim of the traditionally used plant Jasminum auriculatum (J. auriculatum) in skin diseases, by evaluating its wound healing potential along with its antioxidant and antimicrobial properties; so as to understand their role in wound healing. Excision and incision wound models were used to evaluate the wound healing activity on albino rats. The wound healing potential was assessed by measuring rate of wound contraction, epithelialization period, hydroxyproline content, skin breaking strength and histopathological parameters. Reference standard drug was Nitrofurazone ointment. The antioxidant activity was determined using 2, 2-diphenyl-1-picrylhydrazyl (DPPH) method. The antimicrobial activity was determined by agar well diffusion method and minimum inhibitory concentration by serial dilution method. Higher rate of wound contraction (83.66±0.50% on 15th day), decrease in the period of epithelialization (17.83±1.6days), higher skin breaking strength (170.71±1.52g), higher collagen content and favourable histopathological changes revealed that topical application of ointment containing successive ethanolic extract (S.E.E) of J. auriculatum leaves has the most potent wound healing ability compared to control group in both the models studied. The DPPH radical scavenging activity of successive ethanolic extract was found to be 33.39µg/ml. Successive ethanolic extract was found to be most effective against Pseudomonas auregenosa having a zone of inhibition 16.65±0.6mm and the minimum inhibitory concentration was 0.78mg/ml. The data of this study indicate that successive ethanolic extract of the leaves exhibit potent wound healing, antioxidant and antimicrobial properties. This justifies the ethno-medicinal use of plant for the treatment of wound and microbial infections.

Evaluation of wound healing, antioxidant and antimicrobial efficacy of Jasminum auriculatum Vahl. leaves

PubMed Central

Arun, Mittal; Satish, Sardana; Anima, Pandey

2016-01-01

Objective: To validate the ethno-therapeutic claim of the traditionally used plant Jasminum auriculatum (J. auriculatum) in skin diseases, by evaluating its wound healing potential along with its antioxidant and antimicrobial properties; so as to understand their role in wound healing. Materials and Methods: Excision and incision wound models were used to evaluate the wound healing activity on albino rats. The wound healing potential was assessed by measuring rate of wound contraction, epithelialization period, hydroxyproline content, skin breaking strength and histopathological parameters. Reference standard drug was Nitrofurazone ointment. The antioxidant activity was determined using 2, 2-diphenyl-1-picrylhydrazyl (DPPH) method. The antimicrobial activity was determined by agar well diffusion method and minimum inhibitory concentration by serial dilution method. Results: Higher rate of wound contraction (83.66±0.50% on 15th day), decrease in the period of epithelialization (17.83±1.6days), higher skin breaking strength (170.71±1.52g), higher collagen content and favourable histopathological changes revealed that topical application of ointment containing successive ethanolic extract (S.E.E) of J. auriculatum leaves has the most potent wound healing ability compared to control group in both the models studied. The DPPH radical scavenging activity of successive ethanolic extract was found to be 33.39µg/ml. Successive ethanolic extract was found to be most effective against Pseudomonas auregenosa having a zone of inhibition 16.65±0.6mm and the minimum inhibitory concentration was 0.78mg/ml. Conclusion: The data of this study indicate that successive ethanolic extract of the leaves exhibit potent wound healing, antioxidant and antimicrobial properties. This justifies the ethno-medicinal use of plant for the treatment of wound and microbial infections. PMID:27462552

Instability of superfluid Fermi gases induced by a rotonlike density mode in optical lattices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yunomae, Yoshihiro; Yamamoto, Daisuke; Danshita, Ippei

2009-12-15

We study the stability of superfluid Fermi gases in deep optical lattices in the BCS-Bose-Einstein condensation (BEC) crossover at zero temperature. Within the tight-binding attractive Hubbard model, we calculate the spectrum of the low-energy Anderson-Bogoliubov (AB) mode as well as the single-particle excitations in the presence of superfluid flow in order to determine the critical velocities. To obtain the spectrum of the AB mode, we calculate the density response function in the generalized random-phase approximation applying the Green's function formalism developed by Cote and Griffin to the Hubbard model. We find that the spectrum of the AB mode is separatedmore » from the particle-hole continuum having the characteristic rotonlike minimum at short wavelength due to the strong charge-density-wave fluctuations. The energy of the rotonlike minimum decreases with increasing the lattice velocity and it reaches zero at the critical velocity which is smaller than the pair-breaking velocity. This indicates that the superfluid state is energetically unstable due to the spontaneous emission of the short-wavelength rotonlike excitations of the AB mode instead due to pair breaking. We determine the critical velocities as functions of the interaction strength across the BCS-BEC crossover regime.« less

Break-technique handheld dynamometry: relation between angular velocity and strength measurements.

PubMed

Burns, Stephen P; Spanier, David E

2005-07-01

To determine whether the muscle strength, as measured with break-technique handheld dynamometry (HHD), is dependent on the angular velocity achieved during testing and to compare reliability at different angular velocities. Repeated-measures study. Participants underwent HHD by using make-technique (isometric) and break-technique (eccentric) dynamometry at 3 prespecified angular velocities. Elbow movement was recorded with an electrogoniometer. Inpatient spinal cord injury unit. Convenience sample of 20 persons with tetraplegia with weakness of elbow flexors or extensors. Not applicable. Elbow angular velocity and muscle strength recorded during HHD. With the break technique, angular velocities averaging 15 degrees , 33 degrees , and 55 degrees /s produced 16%, 30%, and 51% greater strength measurements, respectively, than velocities recorded by using the make technique (all P < .006 for comparisons between successive techniques). The intraclass correlation coefficient for intrarater reliability was .89 or greater for all testing techniques. Greater strength is recorded with faster angular velocities during HHD. Differences in angular velocity may explain the wide range previously reported for break- versus make-technique strength measurements. Variation in angular velocity is a potential source of variability in serial HHD strength measurements, and for this reason the make technique may be preferable.

Laser-tissue soldering with biodegradable polymer films in vitro: film surface morphology and hydration effects.

PubMed

Sorg, B S; Welch, A J

2001-01-01

Previous research introduced the concept of using biodegradable polymer film reinforcement of a liquid albumin solder for improvement of the tensile strength of repaired incisions in vitro. In this study, the effect of creating small pores in the PLGA films on the weld breaking strength is studied. Additionally, the effect of hydration on the strength of the reinforced welds is investigated. A 50%(w/v) bovine serum albumin solder with 0.5 mg/mL Indocyanine Green dye was used to repair an incision in bovine aorta. The solder was coagulated with an 806-nm CW diode laser. A poly(DL-lactic-co-glycolic acid) (PLGA) film was used to reinforce the solder (the controls had solder but no reinforcement). Breaking strengths were measured acutely and after hydration in saline for 1 and 2 days. The data were analyzed by ANOVA (P < 0.05) and multiple comparisons of means were performed using the Newman-Keuls test. The creation of pores in the PLGA films qualitatively improved the film flexibility without having an apparent adverse effect on the breaking strength, while the actual technique of applying the film and solder had more of an effect. The acute maximum average breaking strengths of some of the film reinforced specimens (114.7 g-134.4 g) were significantly higher (P < 0.05) than the acute maximum average breaking strength of the unreinforced control specimens (68.3 g). Film reinforced specimens were shown to have a statistically significantly higher breaking strength than unreinforced controls after 1- and 2-day hydration. Reinforcement of liquid albumin solders in laser-assisted incision repair appears to have advantages over conventional methods that do not reinforce the cohesive strength of the solder in terms of acute breaking strength and after immersion in moist environments for short periods of time. Using a film with the solder applied to one surface only may be advantageous over other techniques.

Steel Fibers Reinforced Concrete Pipes - Experimental Tests and Numerical Simulation

NASA Astrophysics Data System (ADS)

Doru, Zdrenghea

2017-10-01

The paper presents in the first part a state of the art review of reinforced concrete pipes used in micro tunnelling realised through pipes jacking method and design methods for steel fibres reinforced concrete. In part two experimental tests are presented on inner pipes with diameters of 1410mm and 2200mm, and specimens (100x100x500mm) of reinforced concrete with metal fibres (35 kg / m3). In part two experimental tests are presented on pipes with inner diameters of 1410mm and 2200mm, and specimens (100x100x500mm) of reinforced concrete with steel fibres (35 kg / m3). The results obtained are analysed and are calculated residual flexural tensile strengths which characterise the post-cracking behaviour of steel fibres reinforced concrete. In the third part are presented numerical simulations of the tests of pipes and specimens. The model adopted for the pipes test was a three-dimensional model and loads considered were those obtained in experimental tests at reaching breaking forces. Tensile stresses determined were compared with mean flexural tensile strength. To validate tensile parameters of steel fibres reinforced concrete, experimental tests of the specimens were modelled with MIDAS program to reproduce the flexural breaking behaviour. To simulate post - cracking behaviour was used the method σ — ε based on the relationship stress - strain, according to RILEM TC 162-TDF. For the specimens tested were plotted F — δ diagrams, which have been superimposed for comparison with the similar diagrams of experimental tests. The comparison of experimental results with those obtained from numerical simulation leads to the following conclusions: - the maximum forces obtained by numerical calculation have higher values than the experimental values for the same tensile stresses; - forces corresponding of residual strengths have very similar values between the experimental and numerical calculations; - generally the numerical model estimates a breaking force greater than that obtained in the experimental tests. Experimental and numerical studies are used to establish the residual characteristic flexural tensile strength minimum guaranteed and limits of applicability of concrete pipes reinforced with steel fibres used in various field and loading situations.

Ultrafast-laser dicing of thin silicon wafers: strategies to improve front- and backside breaking strength

NASA Astrophysics Data System (ADS)

Domke, Matthias; Egle, Bernadette; Stroj, Sandra; Bodea, Marius; Schwarz, Elisabeth; Fasching, Gernot

2017-12-01

Thin 50-µm silicon wafers are used to improve heat dissipation of chips with high power densities. However, mechanical dicing methods cause chipping at the edges of the separated dies that reduce the mechanical stability. Thermal load changes may then lead to sudden chip failure. Recent investigations showed that the mechanical stability of the cut chips could be increased using ultrashort-pulsed lasers, but only at the laser entrance (front) side and not at the exit (back) side. The goal of this study was to find strategies to improve both front- and backside breaking strength of chips that were cut out of an 8″ wafer with power metallization using an ultrafast laser. In a first experiment, chips were cut by scanning the laser beam in single lines across the wafer using varying fluencies and scan speeds. Three-point bending tests of the cut chips were performed to measure front and backside breaking strengths. The results showed that the breaking strength of both sides increased with decreasing accumulated fluence per scan. Maximum breaking strengths of about 1100 MPa were achieved at the front side, but only below 600 MPa were measured for the backside. A second experiment was carried out to optimize the backside breaking strength. Here, parallel line scans to increase the distance between separated dies and step cuts to minimize the effect of decreasing fluence during scribing were performed. Bending tests revealed that breaking strengths of about 1100 MPa could be achieved also on the backside using the step cut. A reason for the superior performance could be found by calculating the fluence absorbed by the sidewalls. The calculations suggested that an optimal fluence level to minimize thermal side effects and periodic surface structures was achieved due to the step cut. Remarkably, the best breaking strengths values achieved in this study were even higher than the values obtained on state of the art ns-laser and mechanical dicing machines. This is the first study to the knowledge of the authors, which demonstrates that ultrafast-laser dicing improves the mechanical stability of thin silicon chips.

Tips for longwall conveyor chain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Courtney, J.C.; Fortune, J.

1977-03-01

Mining chain must be capable of sustaining imposed loads of 80 or 90 percent of its minimum breaking strength, and still return to its original dimensions. This means that the chain should behave like an extremely sophisticated spring up to very high load levels, and return to its unloaded state without any plastic stretch or permanent dimensional deformation having taken place. This feature is absolutely essential, not only to enable repeat loadings to be made, but to ensure that constant, precise engagement of the drive and idler sprockets takes place. The mining chain production process, therefore, is carefully designed somore » that the last stage of manufacture introduces these necessary features.« less

Balance between cell-substrate adhesion and myosin contraction determines the frequency of motility initiation in fish keratocytes.

PubMed

Barnhart, Erin; Lee, Kun-Chun; Allen, Greg M; Theriot, Julie A; Mogilner, Alex

2015-04-21

Cells are dynamic systems capable of spontaneously switching among stable states. One striking example of this is spontaneous symmetry breaking and motility initiation in fish epithelial keratocytes. Although the biochemical and mechanical mechanisms that control steady-state migration in these cells have been well characterized, the mechanisms underlying symmetry breaking are less well understood. In this work, we have combined experimental manipulations of cell-substrate adhesion strength and myosin activity, traction force measurements, and mathematical modeling to develop a comprehensive mechanical model for symmetry breaking and motility initiation in fish epithelial keratocytes. Our results suggest that stochastic fluctuations in adhesion strength and myosin localization drive actin network flow rates in the prospective cell rear above a critical threshold. Above this threshold, high actin flow rates induce a nonlinear switch in adhesion strength, locally switching adhesions from gripping to slipping and further accelerating actin flow in the prospective cell rear, resulting in rear retraction and motility initiation. We further show, both experimentally and with model simulations, that the global levels of adhesion strength and myosin activity control the stability of the stationary state: The frequency of symmetry breaking decreases with increasing adhesion strength and increases with increasing myosin contraction. Thus, the relative strengths of two opposing mechanical forces--contractility and cell-substrate adhesion--determine the likelihood of spontaneous symmetry breaking and motility initiation.

Reliability, Validity, and Sensitivity of a Novel Smartphone-Based Eccentric Hamstring Strength Test in Professional Football Players.

PubMed

Lee, Justin W Y; Cai, Ming-Jing; Yung, Patrick S H; Chan, Kai-Ming

2018-05-01

To evaluate the test-retest reliability, sensitivity, and concurrent validity of a smartphone-based method for assessing eccentric hamstring strength among male professional football players. A total of 25 healthy male professional football players performed the Chinese University of Hong Kong (CUHK) Nordic break-point test, hamstring fatigue protocol, and isokinetic hamstring strength test. The CUHK Nordic break-point test is based on a Nordic hamstring exercise. The Nordic break-point angle was defined as the maximum point where the participant could no longer support the weight of his body against gravity. The criterion for the sensitivity test was the presprinting and postsprinting difference of the Nordic break-point angle with a hamstring fatigue protocol. The hamstring fatigue protocol consists of 12 repetitions of the 30-m sprint with 30-s recoveries between sprints. Hamstring peak torque of the isokinetic hamstring strength test was used as the criterion for validity. A high test-retest reliability (intraclass correlation coefficient = .94; 95% confidence interval, .82-.98) was found in the Nordic break-point angle measurements. The Nordic break-point angle significantly correlated with isokinetic hamstring peak torques at eccentric action of 30°/s (r = .88, r 2  = .77, P < .001). The minimal detectable difference was 8.03°. The sensitivity of the measure was good enough that a significance difference (effect size = 0.70, P < .001) was found between presprinting and postsprinting values. The CUHK Nordic break-point test is a simple, portable, quick smartphone-based method to provide reliable and accurate eccentric hamstring strength measures among male professional football players.

24 CFR 904.108 - Break-even amount.

Code of Federal Regulations, 2011 CFR

2011-04-01

... amount. (a) Definition. The term “break-even amount” as used herein means the minimum average monthly... break-even amount, the excess shall constitute additional Project income and shall be deposited and used in the same manner as other Project income. (c) Deficit in monthly payment. When the homebuyer's...

A study of environmental characterization of conventional and advanced aluminum alloys for selection and design. Phase 2: The breaking load test method

NASA Technical Reports Server (NTRS)

Sprowls, D. O.; Bucci, R. J.; Ponchel, B. M.; Brazill, R. L.; Bretz, P. E.

1984-01-01

A technique is demonstrated for accelerated stress corrosion testing of high strength aluminum alloys. The method offers better precision and shorter exposure times than traditional pass fail procedures. The approach uses data from tension tests performed on replicate groups of smooth specimens after various lengths of exposure to static stress. The breaking strength measures degradation in the test specimen load carrying ability due to the environmental attack. Analysis of breaking load data by extreme value statistics enables the calculation of survival probabilities and a statistically defined threshold stress applicable to the specific test conditions. A fracture mechanics model is given which quantifies depth of attack in the stress corroded specimen by an effective flaw size calculated from the breaking stress and the material strength and fracture toughness properties. Comparisons are made with experimental results from three tempers of 7075 alloy plate tested by the breaking load method and by traditional tests of statistically loaded smooth tension bars and conventional precracked specimens.

Methods for the practical determination of the mechanical strength of tablets--from empiricism to science.

PubMed

Podczeck, Fridrun

2012-10-15

This review aims to awake an interest in the determination of the tensile strength of tablets of various shapes using a variety of direct and indirect test methods. The United States Pharmacopoeia monograph 1217 (USP35/NF30, 2011) has provided a very good approach to the experimental determination of and standards for the mechanical strength of tablets. Building on this monograph, it is hoped that the detailed account of the various methods provided in this review will encourage industrial and academic scientists involved in the development and manufacture of tablet formulations to take a step forward and determine the tensile strength of tablets, even if these are not simply flat disc-shaped or rectangular. To date there are a considerable number of valid test configurations and stress equations available, catering for many of the various shapes of tablets on the market. The determination of the tensile strength of tablets should hence replace the sole determination of a breaking force, because tensile strength values are more comparable and suggestions for minimum and/or maximum values are available. The review also identifies the gaps that require urgent filling. There is also a need for further analysis using, for example, Finite Element Method, to provide correct stress solutions for tablets of differing shapes, but this also requires practical experiments to find the best loading conditions, and theoretical stress solutions should be verified with practical experiments. Copyright © 2012 Elsevier B.V. All rights reserved.

Preliminary biocompatibility experiment of polymer films for laser-assisted tissue welding.

PubMed

Sorg, Brian S; Welch, Ashley J

2003-01-01

The purpose of this study was to examine the impact of a polymer film for liquid solder strength reinforcement on the short term healing of a wound closed by laser-tissue soldering. Full thickness incisions created on the dorsum of Sprague-Dawley rats were closed by laser-tissue soldering: albumin solder with Indocyanine Green (ICG) dye was inserted between the incision edges and photothermally coagulated with a diode laser. A poly(DL-lactic-co-glycolic acid) (PLGA) polymer film was implanted subcutaneously in the bottom of the incision (controls had no film). Specimens were harvested at 0, 3, 7, and 14 days for breaking strength testing and histological analysis. Breaking strengths of the controls at 0 and 14 days were statistically stronger than the specimens with the implanted films (t-test, P < 0.05). A slight difficulty in apposing the wound edges due to the film presence may have contributed to the low acute strengths. Interference with the wound contraction process by the films possibly contributed to the lower breaking strength at 14 days. Wound histology indicated a mild foreign body reaction to the polymer film material. The polymer film was well tolerated by the tissue, and the tissue response to the material was consistent with that seen in the literature. The breaking strength differences between control and film-implanted specimens at 0 and 14 days were probably the result of mechanical complications (tissue apposition and wound contraction) due to the presence of the film, and not due to the film material itself. The use of polymer film patches for liquid solder reinforcement and breaking strength enhancement may have certain application specific issues that need to be addressed. Strategies to account for these issues require further research. Copyright 2003 Wiley-Liss, Inc.

[Reinforcement for overdentures on abutment teeth].

PubMed

Osada, Tomoko

2006-04-01

This study investigated the effect of the position of reinforcement wires, differences in artificial teeth, and framework designs on the breaking strength of overdentures. The basal surfaces of composite resin teeth and acrylic resin teeth were removed using a carbide bur. A reinforcement wire or a wrought palatal bar was embedded near the occlusal surface or basal surface. Four types of framework structures were designed : conventional skeleton (skeleton), housing with skeleton (housing), housing plus short metal backing (metal backing), and housing plus long metal backing (double structure). After the wires, bars, and frameworks were sand-blasted with 50 microm Al(2)O(3) powder, they were primed with a metal primer and embedded in a heat-polymerized denture base resin. The breaking strengths (N) and maximum stiffness (N/mm) of two-week aged (37 degrees C) specimens were measured using a bending test (n=8). All data obtained at a crosshead speed of 2.0 mm/min were analyzed by ANOVA/Tukey's test (alpha=0.01). There were no statistical differences between the two kinds of artificial teeth (p>0.01). The wrought palatal bar had significantly higher strength than the reinforcement wire (p<0.01). Greater strengths were found for specimens with frameworks than those without frameworks (p<0.01). The breaking strength of the wrought palatal bar embedded near the occlusal surface was higher than that on the basal surface (p>0.01). The breaking strength and maximum stiffness of the double structure framework were significantly greater (p<0.01) than those of the conventional frameworks. The breaking strengths of overdentures were influenced by the size and position of the reinforcement wires. Double structure frameworks are recommended for overdentures to promote a long-term prognosis without denture breakage.

Effect of Oil Application, Age, Diet, and Pigmentation on the Tensile Strength and Breaking Point of Hair.

PubMed

Kavitha, S; Natarajan, Karthika; Thilagavathi, G; Srinivas, C R

2016-01-01

Hair strength depends on various factors such as nutrition, environmental factors, sunlight, oiling, aging, conditioner, etc. To compare the tensile strength and breaking point of the hair shaft between (1) vegetarian and nonvegetarian. (2) Those who regularly apply and those who do not apply oil. (3) Pigmented and nonpigmented hair, (4) childhood and elderly. Hair fibers were mounted in tensile strength testing machine Zwick/Roell Z010 and gradual force was administered. The elongation of hair fiber in mm and the maximum force required to break the hair strand were recorded for each fiber. Elasticity of the children's hair was more than the elasticity of adult ( P = 0.05) although tensile strength in children hair was not statistically significant (>0.05). Similarly, the tensile strength was more among those who regularly consumed nonvegetarian food but the difference was not statistically significant ( P > 0.05). There was no statistically significant difference in other groups ( P > 0.05). Elasticity in children hair is statistically more than elderly hair although there is no significant change in tensile strength.

32 CFR 147.23 - Breaks in service.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Breaks in service. 147.23 Section 147.23... Standards § 147.23 Breaks in service. If a person who requires access has been retired or separated from U.S... current, the agency regranting the access will, as a minimum, review an updated Standard Form 86 and...

46 CFR 189.35-9 - Plans.

Code of Federal Regulations, 2012 CFR

2012-10-01

... withstand and operate in excess of the breaking strength of the strongest section or wire to be used in any... application of a load equal to the nominal breaking strength of the strongest section or wire rope to be used... or for trailing objects, where the wire rope or cable is payed out beneath the surface and becomes...

46 CFR 189.35-9 - Plans.

Code of Federal Regulations, 2014 CFR

2014-10-01

... withstand and operate in excess of the breaking strength of the strongest section or wire to be used in any... application of a load equal to the nominal breaking strength of the strongest section or wire rope to be used... or for trailing objects, where the wire rope or cable is payed out beneath the surface and becomes...

46 CFR 189.35-9 - Plans.

Code of Federal Regulations, 2013 CFR

2013-10-01

... withstand and operate in excess of the breaking strength of the strongest section or wire to be used in any... application of a load equal to the nominal breaking strength of the strongest section or wire rope to be used... or for trailing objects, where the wire rope or cable is payed out beneath the surface and becomes...

33 CFR 401.12 - Minimum requirements-mooring lines and fairleads.

Code of Federal Regulations, 2010 CFR

2010-07-01

... forward and one mooring line shall lead astern from the break of the bow and shall be independently power... shall lead forward from the break of the bow and one line shall lead astern from the quarter and be... astern from the break of the bow through chocks to suitable mooring bitts on deck; (2) Vessels of more...

78 FR 32700 - Hours of Service of Drivers: U.S. Department of Energy (DOE); Application for Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-31

...) an exemption from the minimum 30-minute rest break provision of the Agency's hours-of-service (HOS... minutes or more of ``attendance time'' to meet the HOS rest break requirements providing they do not perform any other work during the break. DATES: This exemption is effective from July 1, 2013 through June...

A Simple Experiment to Demonstrate the Effects of Cracks on Materials Strength

ERIC Educational Resources Information Center

Sauls, Frederick C.

2011-01-01

A simple in-class experiment was designed to expose students to an aspect of materials science dealing with defects. Students break a series of paper strips to gauge the breaking strength. A precut transverse "crack" weakens the paper strip by a surprising amount. Adding a precut "crack stopper" greatly reduces the effect of the original "crack".…

Textural improvement of salt-reduced Alaska pollack (Theragra chalcogramma) roe product by CaCl2.

PubMed

Chen, Chaoping; Okazaki, Emiko; Osako, Kazufumi

2016-12-15

Salt-reduced Alaska pollack roe benefits public health by decreasing NaCl intake; however, it has a poor texture with low breaking strength. This study addresses the feasibility of NaCl reduction in salted roe products, with focusing on the improvement of breaking strength using CaCl2. Salted roe products were prepared by immersing Alaska pollack roe in either NaCl solutions (3.5, 7.0, 15.0, 20.0, and 25.0%) or 7.0% NaCl solutions with added CaCl2 (0.0, 0.5, 1.0, 2.0, and 3.0%). Breaking strength, moisture and salt contents, eggshell protein composition of the salted roe products, as well as total endogenous transglutaminase (TGase) activity in various NaCl and CaCl2 concentrations were analyzed. CaCl2 addition enhanced eggshell protein crosslinking and breaking strength of the salt-reduced roe products. An acyl transfer reaction catalyzed by calcium-dependent TGase may be responsible for the eggshell protein crosslinking and improved texture. Thus, we successfully developed a salt-reduced Alaska roe product using CaCl2. Copyright © 2016 Elsevier Ltd. All rights reserved.

High Tensile Strength Amalgams for In-Space Fabrication and Repair

NASA Technical Reports Server (NTRS)

Grugel, Richard N.

2006-01-01

Amalgams are well known for their use in dental practice as a tooth filling material. They have a number of useful attributes that include room temperature fabrication, corrosion resistance, dimensional stability, and very good compressive strength. These properties well serve dental needs but, unfortunately, amalgams have extremely poor tensile strength, a feature that severely limits other potential applications. Improved material properties (strength and temperature) of amalgams may have application to the freeform fabrication of repairs or parts that might be necessary during an extended space mission. Advantages would include, but are not limited to: the ability to produce complex parts, a minimum number of processing steps, minimum crew interaction, high yield - minimum wasted material, reduced gravity compatibility, minimum final finishing, safety, and minimum power consumption. The work presented here shows how the properties of amalgams can be improved by changing particle geometries in conjunction with novel engineering metals.

49 CFR 179.220-7 - Materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... indicated minimum tensile strength and elongation in the welded condition. (b) Carbon steel plate: The...) High alloy steel plate: High alloy steel plate must comply with one of the following specifications... Minimum tensile strength (p.s.i.) welded condition 1 Minimum elongation in 2 inches (percent) weld metal...

49 CFR 179.220-7 - Materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... indicated minimum tensile strength and elongation in the welded condition. (b) Carbon steel plate: The...) High alloy steel plate: High alloy steel plate must comply with one of the following specifications... Minimum tensile strength (p.s.i.) welded condition 1 Minimum elongation in 2 inches (percent) weld metal...

49 CFR 179.220-7 - Materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... indicated minimum tensile strength and elongation in the welded condition. (b) Carbon steel plate: The...) High alloy steel plate: High alloy steel plate must comply with one of the following specifications... Minimum tensile strength (p.s.i.) welded condition 1 Minimum elongation in 2 inches (percent) weld metal...

49 CFR 179.220-7 - Materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... indicated minimum tensile strength and elongation in the welded condition. (b) Carbon steel plate: The...) High alloy steel plate: High alloy steel plate must comply with one of the following specifications... Minimum tensile strength (p.s.i.) welded condition 1 Minimum elongation in 2 inches (percent) weld metal...

Ideal strength of bcc molybdenum and niobium

NASA Astrophysics Data System (ADS)

Luo, Weidong; Roundy, D.; Cohen, Marvin L.; Morris, J. W.

2002-09-01

The behavior of bcc Mo and Nb under large strain was investigated using the ab initio pseudopotential density-functional method. We calculated the ideal shear strength for the {211}<111> and {011}<111> slip systems and the ideal tensile strength in the <100> direction, which are believed to provide the minimum shear and tensile strengths. As either material is sheared in either of the two systems, it evolves toward a stress-free tetragonal structure that defines a saddle point in the strain-energy surface. The inflection point on the path to this tetragonal ``saddle-point'' structure sets the ideal shear strength. When either material is strained in tension along <100>, it initially follows the tetragonal, ``Bain,'' path toward a stress-free fcc structure. However, before the strained crystal reaches fcc, its symmetry changes from tetragonal to orthorhombic; on continued strain it evolves toward the same tetragonal saddle point that is reached in shear. In Mo, the symmetry break occurs after the point of maximum tensile stress has been passed, so the ideal strength is associated with the fcc extremum as in W. However, a Nb crystal strained in <100> becomes orthorhombic at tensile stress below the ideal strength. The ideal tensile strength of Nb is associated with the tetragonal saddle point and is caused by failure in shear rather than tension. In dimensionless form, the ideal shear and tensile strengths of Mo (τ*=τm/G111=0.12, σ*=σm/E100=0.078) are essentially identical to those previously calculated for W. Nb is anomalous. Its dimensionless shear strength is unusually high, τ*=0.15, even though the saddle-point structure that causes it is similar to that in Mo and W, while its dimensionless tensile strength, σ*=0.079, is almost the same as that of Mo and W, even though the saddle-point structure is quite different.

Effects of fishing rope strength on the severity of large whale entanglements.

PubMed

Knowlton, Amy R; Robbins, Jooke; Landry, Scott; McKenna, Henry A; Kraus, Scott D; Werner, Timothy B

2016-04-01

Entanglement in fixed fishing gear affects whales worldwide. In the United States, deaths of North Atlantic right (Eubalaena glacialis) and humpback whales (Megaptera novaeangliae) have exceeded management limits for decades. We examined live and dead whales entangled in fishing gear along the U.S. East Coast and the Canadian Maritimes from 1994 to 2010. We recorded whale species, age, and injury severity and determined rope polymer type, breaking strength, and diameter of the fishing gear. For the 132 retrieved ropes from 70 cases, tested breaking strength range was 0.80-39.63 kN (kiloNewtons) and the mean was 11.64 kN (SD 8.29), which is 26% lower than strength at manufacture (range 2.89-53.38 kN, mean = 15.70 kN [9.89]). Median rope diameter was 9.5 mm. Right and humpback whales were found in ropes with significantly stronger breaking strengths at time of manufacture than minke whales (Balaenoptera acuturostrata) (19.30, 17.13, and 10.47 mean kN, respectively). Adult right whales were found in stronger ropes (mean 34.09 kN) than juvenile right whales (mean 15.33 kN) and than all humpback whale age classes (mean 17.37 kN). For right whales, severity of injuries increased since the mid 1980s, possibly due to changes in rope manufacturing in the mid 1990s that resulted in production of stronger ropes at the same diameter. Our results suggest that broad adoption of ropes with breaking strengths of ≤ 7.56 kN (≤ 1700 lbsf) could reduce the number of life-threatening entanglements for large whales by at least 72%, and yet could provide sufficient strength to withstand the routine forces involved in many fishing operations. A reduction of this magnitude would achieve nearly all the mitigation legally required for U.S. stocks of North Atlantic right and humpback whales. Ropes with reduced breaking strength should be developed and tested to determine the feasibility of their use in a variety of fisheries. © 2015 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

46 CFR 117.137 - Stowage of life floats and buoyant apparatus.

Code of Federal Regulations, 2012 CFR

2012-10-01

... used to attach the float-free link to the vessel must: (1) Have a breaking strength of at least the breaking strength of the painter; (2) If synthetic, be of a dark color or of a type certified to be... painter must be provided by a wire or line which: (1) Encircles the body of the device; (2) Will not slip...

46 CFR 117.137 - Stowage of life floats and buoyant apparatus.

Code of Federal Regulations, 2013 CFR

2013-10-01

... used to attach the float-free link to the vessel must: (1) Have a breaking strength of at least the breaking strength of the painter; (2) If synthetic, be of a dark color or of a type certified to be... painter must be provided by a wire or line which: (1) Encircles the body of the device; (2) Will not slip...

Comparison of breaking tests for the characterization of the interfacial strength of bilayer tablets.

PubMed

Castrati, Luca; Mazel, Vincent; Busignies, Virginie; Diarra, Harona; Rossi, Alessandra; Colombo, Paolo; Tchoreloff, Pierre

2016-11-20

The bilayer tableting technology is gaining more acceptance in the drug industry, due to its ability to improve the drug delivery strategies. It is currently assessed by the European Pharmacopoeia, that the mechanical strength of tablets can be evaluated using a diametral breaking tester. This device applies a force diametrically, and records the tablet breaking point. This approach has been used to measure the structural integrity of single layer tablets as well as bilayer (and multi-layer) tablets. The latter ones, however, have a much complex structure. Therefore, testing a bilayer tablet with the currently used breaking test methodology might not be appropriate. The aim of this work was to compare results from several tests that have been proposed to quantify the interfacial strength of bilayer tablets. The obtained results would provide an indication on which tests are appropriate to evaluate the robustness of a bilayer tablet. Bilayer tablets were fabricated using a model formulation: Microcrystalline Cellulose (MCC) for the first layer, and spray dried lactose (SDLac) as second layer. Each set of tablets were tested using the following tests: Diametral Test, Shear Test and Indentation Test. The tablets were examined before and after the breaking test using Scanning Electron Microscopy (SEM). When a bilayer tablet was subjected to shearing or indentation, it showed signs of clear delamination. Differently, using the diametral test system, the tablets showed no clear difference, before and after the testing. However, when examining each layer via SEM, it was clear that a fracture occurred in the layer made of SDLac. Thus, the diametral test is a measure of the strength of one of the two layers and therefore it is not suited to test the mechanical strength of bilayer tablets. Copyright © 2016 Elsevier B.V. All rights reserved.

47 CFR 73.189 - Minimum antenna heights or field strength requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Minimum antenna heights or field strength... RADIO SERVICES RADIO BROADCAST SERVICES AM Broadcast Stations § 73.189 Minimum antenna heights or field..., frequency, or transmitter location must also request authority to install a new antenna system or to make...

47 CFR 73.189 - Minimum antenna heights or field strength requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Minimum antenna heights or field strength... RADIO SERVICES RADIO BROADCAST SERVICES AM Broadcast Stations § 73.189 Minimum antenna heights or field..., frequency, or transmitter location must also request authority to install a new antenna system or to make...

47 CFR 73.189 - Minimum antenna heights or field strength requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Minimum antenna heights or field strength... RADIO SERVICES RADIO BROADCAST SERVICES AM Broadcast Stations § 73.189 Minimum antenna heights or field..., frequency, or transmitter location must also request authority to install a new antenna system or to make...

47 CFR 73.189 - Minimum antenna heights or field strength requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Minimum antenna heights or field strength... RADIO SERVICES RADIO BROADCAST SERVICES AM Broadcast Stations § 73.189 Minimum antenna heights or field..., frequency, or transmitter location must also request authority to install a new antenna system or to make...

47 CFR 73.189 - Minimum antenna heights or field strength requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Minimum antenna heights or field strength... RADIO SERVICES RADIO BROADCAST SERVICES AM Broadcast Stations § 73.189 Minimum antenna heights or field..., frequency, or transmitter location must also request authority to install a new antenna system or to make...

Parameters of tensile strength, elongation, and tenacity of 70mm IIaO spectroscopic film

NASA Technical Reports Server (NTRS)

Hammond, Ernest C., Jr.; Peters, Kevin A.

1989-01-01

The 70mm IIaO spectroscopic film was tested to determine its tensile strength, elongation, and breaking strength, using an Instron (strength and compression) 4201 Test Instrument. These data provide information leading to the upper and lower limits of the above parameters for 70mm IIaO spectroscopic film. This film will be developed by a commercial developing machine after the Ultraviolet Telescope Space Shuttle Mission returns to the Earth in the early 1990's; thus, it is necessary to understand these force parameters. Several test strips of approximately 200mm in length were used. The results indicate that when a stress load of 100 kg was applied, the film elongated approximately 1.06mm and the break strength was 19.45 kilograms.

Autonomous Sensor Motes Employing Liquid-Bearing Rotary Stages

DTIC Science & Technology

2014-03-06

breaks off (Fig. 27d) as shown in the sudden change in force, indicating rotor pull off. The minimum of each curve indicates the maximum tensile load...configuration, with marks on the curves at the minimum energy positions are shown in Fig. 39. The minimum energy positions from Fig. 39are plotted as...rates between 5 and 17 Hz rotation rate plotted vs. rotor eccentricity. The minimum energy positions are indicated on each curve . 3.3 Discussion

Breaking of axial symmetry in excited heavy nuclei as identified in giant dipole resonance data

DOE PAGES

Grosse, E.; Junghans, A. R.; Massarczyk, R.

2017-11-28

Here, a recent theoretical prediction of a breaking of axial symmetry in quasi all heavy nuclei is confronted to a new critical analysis of photon strength functions of nuclei in the valley of stability. For the photon strength in the isovector giant dipole resonance (IVGDR) regime a parameterization of GDR shapes by the sum of three Lorentzians (TLO) is extrapolated to energies below and above the IVGDR. The impact of non-GDR modes adding to the low energy slope of photon strength is discussed including recent data on photon scattering and other radiative processes. These are shown to be concentrated inmore » energy regions where various model calculations predict intermediate collective strength; thus they are obviously separate from the IVGDR tail. The triple Lorentzian (TLO) ansatz for giant dipole resonances is normalized in accordance to the dipole sum rule. The nuclear droplet model with surface dissipation accounts well for positions and widths without local, nuclide specific, parameters. Very few and only global parameters are needed when a breaking of axial symmetry already in the valley of stability is admitted and hence a reliable prediction for electric dipole strength functions also outside of it is expected.« less

Breaking of axial symmetry in excited heavy nuclei as identified in giant dipole resonance data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grosse, E.; Junghans, A. R.; Massarczyk, R.

Here, a recent theoretical prediction of a breaking of axial symmetry in quasi all heavy nuclei is confronted to a new critical analysis of photon strength functions of nuclei in the valley of stability. For the photon strength in the isovector giant dipole resonance (IVGDR) regime a parameterization of GDR shapes by the sum of three Lorentzians (TLO) is extrapolated to energies below and above the IVGDR. The impact of non-GDR modes adding to the low energy slope of photon strength is discussed including recent data on photon scattering and other radiative processes. These are shown to be concentrated inmore » energy regions where various model calculations predict intermediate collective strength; thus they are obviously separate from the IVGDR tail. The triple Lorentzian (TLO) ansatz for giant dipole resonances is normalized in accordance to the dipole sum rule. The nuclear droplet model with surface dissipation accounts well for positions and widths without local, nuclide specific, parameters. Very few and only global parameters are needed when a breaking of axial symmetry already in the valley of stability is admitted and hence a reliable prediction for electric dipole strength functions also outside of it is expected.« less

Mechanical properties of biocompatible clay/P(MEO2MA-co-OEGMA) nanocomposite hydrogels.

PubMed

Xiang, Hengxue; Xia, Mengge; Cunningham, Alexander; Chen, Wei; Sun, Bin; Zhu, Meifang

2017-08-01

The effects of crosslinking density, polymer concentration and monomer ratio on the mechanical properties (tensile and compressive properties) of biocompatible clay/P(MEO 2 MA-co-OEGMA) nanocomposite (NC) hydrogels were investigated. These novel NC hydrogels, composed of inorganic/organic networks, were prepared via in-situ free radical polymerization. The results showed that with increasing inorganic crosslinking agent, i.e. clay concentration, an increase in the tensile strength, elongation at break and compressive strength was observed. Similarly, with increasing polymer concentration, the tensile strength and compressive strength of the NC hydrogels increased while the elongation at break decreased. Increasing the molar concentration of OEGMA in the comonomer led to an increase in the tensile strength of the NC hydrogels but a reduction in the compressive strength. Moreover, clay/P(MEO 2 MA-co-OEGMA) NC hydrogels presented good biocompatibility bolstering their application as tissue engineering scaffolds. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wave Breaking Dissipation in Fetch-Limited Seas

NASA Astrophysics Data System (ADS)

Schwendeman, M.; Thomson, J. M.; Gemmrich, J.

2012-12-01

Breaking waves on the ocean surface control wave growth and enhance air-sea interaction, yet field measurements of breaking are limited. A promising technique for field measurements of wave breaking uses the breaking crest length distribution Λ(c), introduced by Phillips (1985). However, calculating dynamic quantities from Λ(c) requires knowledge of the breaking strength parameter, b. Estimates of a b have varied over many orders of magnitude, and recent studies have attempted to model b in terms of sea state, such as wave steepness or saturation. We present comprehensive observations of breaking in fetch-limited conditions from Juan de Fuca Strait, WA. The wave evolution along fetch is explained by an observed energy budget using the radiative transfer equation (RTE), and the evolution is consistent with existing empirical fetch laws. Estimates of Λ(c) increase along fetch and are consistent with directly measured breaking rates. Using novel in situ measures of dissipation, as well as a residual term from the RTE budget, we obtain robust estimates of the wave breaking strength b. Results suggest that b decreases with wave steepness and saturation, in contrast with recent laboratory results (Drazen et al, 2008). This trend is discussed in terms of the fetch evolution and associated broadening of the equilibrium range in the wave spectra.Map of drifter tracks colored by wave height for two days in Juan de Fuca Strait, WA.

Riveting in metal airplane construction. Part III : strength of riveted joints in duralumin (continued)

NASA Technical Reports Server (NTRS)

Pleines, Wilhelm

1930-01-01

This report includes strength of riveted joints in duralumin, descriptions of test procedure and results of tests. Tabulated data includes: curshing strength by failure for various conditions, shearing strength of hole edge zone in direction of tearing, tearing strengths of plates weakened by rivet holes, and enlargement of holes at beginning of break.

Amnion-Derived Multipotent Progenitor Cells Increase Gain of Incisional Breaking Strength and Decrease Incidence and Severity of Acute Wound Failure

PubMed Central

Xing, Liyu; Franz, Michael G.; Marcelo, Cynthia L.; Smith, Charlotte A.; Marshall, Vivienne S.; Robson, Martin C.

2007-01-01

Objective: Acute wound failure is a common complication following surgical procedures and trauma. Laparotomy wound failure leads to abdominal dehiscence and incisional hernia formation. Delayed recovery of wound-breaking strength is one mechanism for laparotomy wound failure. Early fascial wounds are relatively acellular, and there is a delay in the appearance of acute wound growth factors and cytokines. The objective of this study was to accelerate and improve laparotomy wound healing using amnion-derived multipotent cells (AMPs). AMPs' nonimmunogenic phenotype and relative abundance support its role as a cell therapy. Methods: AMPs were injected into the load-bearing layer of rat abdominal walls prior to laparotomy, and cell viability was confirmed. Wound mechanical properties were measured over 28 days. The incidence and severity of laparotomy wound failure was measured in an incisional hernia model. Results: AMP cells were viable in laparotomy wounds for at least 28 days and did not migrate to other tissues. Laparotomy wound-breaking strength was increased by postoperative day 7 following AMP therapy. AMP therapy reduced the incidence of hernia formation and the size of hernia defects. Histology suggested stimulated wound fibroplasia and angiogenesis. Conclusions: AMP cell therapy reduces the incidence of laparotomy wound failure by accelerating the recovery of wound-breaking strength. This results in fewer incisional hernias and smaller hernia defects. PMID:18091982

Incorporation of coconut shell based nanoparticles in kenaf/coconut fibres reinforced vinyl ester composites

NASA Astrophysics Data System (ADS)

S, Abdul Khalil H. P.; Masri, M.; Saurabh, Chaturbhuj K.; Fazita, M. R. N.; Azniwati, A. A.; Sri Aprilia, N. A.; Rosamah, E.; Dungani, Rudi

2017-03-01

In the present study, a successful attempt has been made on enhancing the properties of hybrid kenaf/coconut fibers reinforced vinyl ester composites by incorporating nanofillers obtained from coconut shell. Coconut shells were grinded followed by 30 h of high energy ball milling for the production of nanoparticles. Particle size analyzer demonstrated that the size of 90% of obtained nanoparticles ranged between 15-140 nm. Furthermore, it was observed that the incorporation of coconut shell nanofillers into hybrid composite increased water absorption capacity. Moreover, tensile, flexural, and impact strength increased with the filler loading up to 3 wt.% and thereafter decrease was observed at higher filler concentration. However, elongation at break decreased and thermal stability increased in nanoparticles concentration dependent manner. Morphological analysis of composite with 3% of filler loading showed minimum voids and fiber pull outs and this indicated that the stress was successfully absorbed by the fiber.

The effect of carbon black (CB) loading on curing characteristics and mechanical properties of virgin acrylonitrile butadiene rubber (Nbrv)/recycled acrylonitrile butadiene rubber (Nbrr) blends

NASA Astrophysics Data System (ADS)

Husnan, M. A.; Ismail, H.; Shuib, R. K.

2018-02-01

Recently, the interest of polymer industry researchers have grown rapidly on the use of specific techniques which can reduce cost and utilize rubber waste into the processing form. The increasing of cognizance in environmental matters and the desire to sustain the resources had fortified the practice of recycling waste materials. In this work, the effect of carbon black loading on curing characteristics and mechanical properties of virgin acrylonitrile butadiene rubber/recycled acrylonitrile butadiene rubber (NBRv/NBRr) blends were studied. Cure time (t90), scorch time (tS2) and swelling percentage decreased but minimum torque (ML) and maximum torque (MH) increased with increasing carbon black (CB) loading in the blends. Increasing CB loading also increased tensile strength, tensile modulus (M100), hardness and compression set but decreased elongation at break (Eb) of NBRv/NBRr blends.

The bending strength of tablets with a breaking line--Comparison of the results of an elastic and a "brittle cracking" finite element model with experimental findings.

PubMed

Podczeck, Fridrun; Newton, J Michael; Fromme, Paul

2015-11-10

The aim of this work was to ascertain the influence of the position of the breaking line of bevel-edged tablets in a three-point bending test. Two different brands of commercially available, flat-round, bevel-edged tablets with a single central breaking line were studied. Breaking line positions tested, relative to the upper loading roll, were 0°, 22.5°, 45°, 67.5° and 90°. The breaking line faced either up- or downwards during the test. The practical results were compared with FEM results simulating similar test configurations. Tablets failed mainly across the failure plane, resulting in two tablet halves. An exception to this was found for tablets where the breaking line faced down and was positioned at an angle of 22.5° relative to the loading plane. Here the crack followed the breaking line in the centre of the tablets and only diverged towards the loading plane position at the edges of the tablets. The breaking line facing upwards resulted in a significantly higher tensile strength of the tablets compared to it facing downwards. However, with one exception, the orientation of the breaking line relative to the loading plane appeared not to affect the tensile strength values. A fully elastic FEM model indicated that both the position of the breaking line relative to the loading plane and as to whether the breaking line faced up- or downwards during the bending test would result in considerably different failure loads during practical experiments. The results also suggested that regardless of the breaking line position, when it is facing down crack propagation should start at the outer edges propagating towards the midpoint of the discs until failure occurs. Failure should hence always result in equal tablet halves, whereby the failure plane should coincide with the loading plane. Neither predictions fully reflected the practical behaviour of the tablets. Using a brittle cracking FEM model significantly larger tensile stresses for tablets with the breaking line positioned downwards at 0° or 22.5° relative to the loading plane were still predicted, but the differences between model and experimental values was greatly reduced. The remaining differences are more likely due to the inadequacy of the equation available to calculate the experimental tensile strength values. This equation cannot account for the presence of a breaking line and overestimates the thickness of the loading plane by the depth of the breaking line when in 0° or 22.5° position. If the depth of the breaking line is taken into account, the model predictions and the experimental findings are comparable. Also, in the brittle cracking FEM simulations the predicted crack propagation patterns were similar to those found in the experiments, and the model stress distributions across the lower surfaces were much more homogeneous and streamlined parallel to the loading plane. The brittle cracking model hence reflected the practicalities of the bending test more closely. The findings suggested that with the breaking line facing down fracture should always start in the centre of a tablet at its lower surface, initiated by the breaking line. Due to simultaneous development of larger stresses along the y-axis the tablet should still break into two equal halves along the loading plane, unless the position of the breaking line relative to the loading plane was 22.5°. In this case the tablet would fail by a mixed process, whereby failure would occur mainly along the breaking line, but due to simultaneous crack formation at the lower surface close to the bevel edge parallel to the loading plane the final breaking pattern would deviate from the breaking line about half-way from its centre, as seen in the practical experiments. Copyright © 2015 Elsevier B.V. All rights reserved.

Material Properties Analysis of Structural Members in Pumpkin Balloons

NASA Technical Reports Server (NTRS)

Sterling, W. J.

2003-01-01

The efficient design, service-life qualification, and reliability predictions for lightweight aerospace structures require careful mechanical properties analysis of candidate structural materials. The demand for high-quality laboratory data is particularly acute when the candidate material or the structural design has little history. The pumpkin-shaped super-pressure balloon presents both challenges. Its design utilizes load members (tendons) extending from apex to base around the gas envelope to achieve a lightweight structure. The candidate tendon material is highly weight-efficient braided HM cord. Previous mechanical properties studies of Zylon have focused on fiber and yarn, and industrial use of the material in tensile applications is limited. For high-performance polymers, a carefully plamed and executed properties analysis scheme is required to ensure the data are relevant to the desired application. Because no directly-applicable testing standard was available, a protocol was developed based on guidelines fiom professional and industry organizations. Due to the liquid-crystalline nature of the polymer, the cord is very stiff, creeps very little, and does not yield. Therefore, the key material property for this application is the breaking strength. The pretension load and gauge length were found to have negligible effect on the measured breaking strength over the ranges investigated. Strain rate was found to have no effect on breaking strength, within the range of rates suggested by the standards organizations. However, at the lower rate more similar to ULDB operations, the strength was reduced. The breaking strength increased when the experiment temperature was decreased from ambient to 183K which is the lowest temperature ULDB is expected to experience. The measured strength under all test conditions was well below that resulting from direct scale-up of fiber strength based on the manufacturers data. This expected result is due to the effects of the braiding process and material ageing.

76 FR 60405 - Inflatable Personal Flotation Devices

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-29

... criteria for the grab breaking strength, tear strength, seam strength, and permeability tests for inflation... Determining Gas Permeability Characteristics of Plastic Film and Sheeting), because those standards, or... Government and Indian tribes, or on the distribution of power and responsibilities between the Federal...

76 FR 17561 - Inflatable Personal Flotation Devices

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-30

... the grab breaking strength, tear strength, seam strength, and permeability tests for inflation chamber... Coated Fabrics), and ASTM D 1434-82 (Standard Test Method for Determining Gas Permeability... Government and Indian tribes, or on the distribution of power and responsibilities between the Federal...

A critical Examination of the Phenomenon of Bonding Area - Bonding Strength Interplay in Powder Tableting.

PubMed

Osei-Yeboah, Frederick; Chang, Shao-Yu; Sun, Changquan Calvin

2016-05-01

Although the bonding area (BA) and bonding strength (BS) interplay is used to explain complex tableting behaviors, it has never been experimentally proven. The purpose of this study is to unambiguously establish the distinct contributions of each by decoupling the contributions from BA and BS. To modulate BA, a Soluplus® powder was compressed into tablets at different temperatures and then broken following equilibration at 25°C. To modulate BS, tablets were equilibrated at different temperatures. To simultaneously modulate BA and BS, both powder compression and tablet breaking test were carried out at different temperatures. Lower tablet tensile strength is observed when the powder is compressed at a lower temperature but broken at 25°C. This is consistent with the increased resistance to polymer deformation at lower temperatures. When equilibrated at different temperatures, the tensile strength of tablets prepared under identical conditions increases with decreasing storage temperature, indicating that BS is higher at a lower temperature. When powder compression and tablet breaking are carried out at the same temperature, the profile with a maximum tensile strength at 4°C is observed due to the BA-BS interplay. By systematically varying temperature during tablet compression and breaking, we have experimentally demonstrated the phenomenon of BA-BS interplay in tableting.

The effects of chronic ketorolac tromethamine (toradol) on wound healing.

PubMed

Haws, M J; Kucan, J O; Roth, A C; Suchy, H; Brown, R E

1996-08-01

Intramuscular ketorolac is a commonly used nonsteroidal anti-inflammatory (NSAI) agent for analgesia in surgical patients. Increasing numbers of surgical patients are chronically taking some form of an NSAI drug. We examined the effects of "chronic" intramuscular ketorolac on the healing of a closed linear surgical wound in the rat. Wistar rats were pretreated with 4 mg per kilogram per day ketorolac intramuscularly prior to receiving dorsal incisional wounds. The ketorolac treatment was continued and after 2 weeks the wounds were excised and separated with a tensiometer to measure mechanical properties. Breaking strength was directly measured, tensile strength was calculated, and collagen concentrations at the wound site were determined. A significant decrease in the mean breaking strength was seen in the ketorolac-treated animals when compared to controls. The ketorolac-treated animals had a mean tensile strength less than the controls, although this difference did not reach statistical significance. The mean collagen concentration of the ketorolac-treated wounds was significantly less than the untreated wounds. Use of ketorolac for just 1 week prior to surgery in rats produced a significant decrease in the breaking strength of their wounds. With the increasing use of ketorolac in surgical patients as well as the increasing use of oral NSAI drugs, more study of this effect is warranted.

Determination of Parachute Joint Factors using Seam and Joint Testing

NASA Technical Reports Server (NTRS)

Mollmann, Catherine

2015-01-01

This paper details the methodology for determining the joint factor for all parachute components. This method has been successfully implemented on the Capsule Parachute Assembly System (CPAS) for the NASA Orion crew module for use in determining the margin of safety for each component under peak loads. Also discussed are concepts behind the joint factor and what drives the loss of material strength at joints. The joint factor is defined as a "loss in joint strength...relative to the basic material strength" that occurs when "textiles are connected to each other or to metals." During the CPAS engineering development phase, a conservative joint factor of 0.80 was assumed for each parachute component. In order to refine this factor and eliminate excess conservatism, a seam and joint testing program was implemented as part of the structural validation. This method split each of the parachute structural joints into discrete tensile tests designed to duplicate the loading of each joint. Breaking strength data collected from destructive pull testing was then used to calculate the joint factor in the form of an efficiency. Joint efficiency is the percentage of the base material strength that remains after degradation due to sewing or interaction with other components; it is used interchangeably with joint factor in this paper. Parachute materials vary in type-mainly cord, tape, webbing, and cloth -which require different test fixtures and joint sample construction methods. This paper defines guidelines for designing and testing samples based on materials and test goals. Using the test methodology and analysis approach detailed in this paper, the minimum joint factor for each parachute component can be formulated. The joint factors can then be used to calculate the design factor and margin of safety for that component, a critical part of the design verification process.

Dynamic breaking of a single gold bond

NASA Astrophysics Data System (ADS)

Pobelov, Ilya V.; Lauritzen, Kasper Primdal; Yoshida, Koji; Jensen, Anders; Mészáros, Gábor; Jacobsen, Karsten W.; Strange, Mikkel; Wandlowski, Thomas; Solomon, Gemma C.

2017-07-01

While one might assume that the force to break a chemical bond gives a measure of the bond strength, this intuition is misleading. If the force is loaded slowly, thermal fluctuations may break the bond before it is maximally stretched, and the breaking force will be less than the bond can sustain. Conversely, if the force is loaded rapidly it is more likely that the maximum breaking force is measured. Paradoxically, no clear differences in breaking force were observed in experiments on gold nanowires, despite being conducted under very different conditions. Here we explore the breaking behaviour of a single Au-Au bond and show that the breaking force is dependent on the loading rate. We probe the temperature and structural dependencies of breaking and suggest that the paradox can be explained by fast breaking of atomic wires and slow breaking of point contacts giving very similar breaking forces.

High Tensile Strength Amalgams for In-Space Repair and Fabrication

NASA Technical Reports Server (NTRS)

Grugel, R. N.

2005-01-01

Amalgams are defined as an alloy of mercury with one or more other metals. These, along with those based on gallium (also liquid at near room temperature), are widely used in dental practice as a tooth filling material. Amalgams have a number of useful attributes that indude room temperature compounding. corrosion resistance, dimensional stability, and good compressive strength. These properties well serve dental needs but, unfortunately, amalgams have extremely poor tensile strength, a feature that severely limits their applications. The work presented here demonstrates how, by modifying particle geometry, the tensile strength of amalgams can be increased and thus extending the range of potential applications. This is relevant to, for example, the freeform fabrication of replacement parts that might be necessary during an extended space mission. Advantages, i.e. Figures-of-Merit. include the ability to produce complex parts, minimum crew interaction, high yield - minimum wasted material, reduced gravity compatibility, minimum final finishing, safety, and minimum power consumption.

Nature's technical ceramic: the avian eggshell

PubMed Central

Hahn, Eric N.; Sherman, Vincent R.; Pissarenko, Andrei; Rohrbach, Samuel D.; Fernandes, Daniel J.

2017-01-01

Avian eggshells may break easily when impacted at a localized point; however, they exhibit impressive resistance when subjected to a well-distributed compressive load. For example, a common demonstration of material strength is firmly squeezing a chicken egg along its major axis between one's hands without breaking it. This research provides insight into the underlying mechanics by evaluating both macroscopic and microstructural features. Eggs of different size, varying from quail (30 mm) to ostrich (150 mm), are investigated. Compression experiments were conducted along the major axis of the egg using force-distributing rubber cushions between steel plates and the egg. The force at failure increases with egg size, reaching loads upwards of 5000 N for ostrich eggs. The corresponding strength, however, decreases with increasing shell thickness (intimately related to egg size); this is rationalized by a micro-defects model. Failure occurs by axial splitting parallel to the loading direction—the result of hoop tensile stresses due to the applied compressive load. Finite-element analysis is successfully employed to correlate the applied compressive force to tensile breaking strength for the eggs, and the influence of geometric ratio and microstructural heterogeneities on the shell's strength and fracture toughness is established. PMID:28123095

46 CFR 160.076-11 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... following methods: (1) Method 5100, Strength and Elongation, Breaking of Woven Cloth; Grab Method, 160.076-25; (2) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method, 160.076-25; (3) Method 5134, Strength of Cloth, Tearing; Tongue Method, 160.076-25. Underwriters Laboratories (UL) Underwriters...

Effect of reactive agent and transesterification catalyst on properties of PLA/PBAT blends

NASA Astrophysics Data System (ADS)

Pitivut, S.; Suttiruengwong, S.; Seadan, M.

2015-07-01

This research aimed to study the properties of poly (lactic acid) (PLA)/poly (butylene adipate-co-terephthalate) (PBAT) blends with two different reactive systems: free radical reaction through peroxide (Perkadox) and transesterification catalyst (tetrabutyl titanate; TBT). Two blends composed of PLA as a matrix phase with the composition of 80 and 70 percent by weight. PLA/PBAT blends with Perkadox were prepared in twin screw extruder, whereas PLA/PBAT blends with TBT were prepared in an internal mixer. The morphology of the blends was investigated by scanning electron microscope (SEM). Tensile and impact testingsof the blends were reported. In case of the blends with Perkadox, SEM micrographs revealed that the size of particles was substantially reduced when adding more Perkadox. Young's modulus and the tensile strength of all blend ratios were insignificantly changed, whereas the elongation at break was decreased when compared to non-reactive blends due to the possible crosslinking reaction as observed from melt flow index (MFI) values. When adding Perkadox, the impact strength of PLA/PBAT (80/20) remained almost unchanged. However, the impact strength of PLA/PBAT (70/30) was enhanced, increasing to 110% for 0.05 phr Perkadox. In case of the blends with TBT, SEM micrographs showed the decrease in the particle size of PBAT phase when adding TBT. Young's modulus and the tensile strength of all blend ratios were not different, but the elongation at break was improved when adding TBT owing to the transesterification reaction. For PLA/PBAT (80/20), the elongation at break was increased by 39%, whereas the elongation at break was increased by 15% for PLA/PLA (70/30). The impact strength of all blend ratios unaffected.

The assessment of bond strength between heat damaged concrete and high strength fibre reinforced concrete

NASA Astrophysics Data System (ADS)

Zahid, M. Z. A. Mohd; Muhamad, K.

2017-09-01

The aim of this study is to assess the bond strength between heat damaged concrete and high strength fibre reinforced concrete (HPFRC). Firstly, this paper presents the various steps taken to prepare the HPFRC with self-compacting property. The minimum targeted slump flow is 600 mm and minimum targeted compressive strength is 80 MPa. The key mix variables considered are such as type of superplasticizer, water cement ratio and silica fume content. Then, the bond strength between the heat damaged concrete with HPFRC was examined. The experimental parameters are heating temperature, surface treatment technique and curing method and the results show that, all experimental parameters are significantly affected the bond strength between heat damaged concrete and HPFRC.

Trends in record-breaking temperatures for the conterminous United States

NASA Astrophysics Data System (ADS)

Rowe, Clinton M.; Derry, Logan E.

2012-08-01

In an unchanging climate, record-breaking temperatures are expected to decrease in frequency over time, as established records become increasingly more difficult to surpass. This inherent trend in the number of record-breaking events confounds the interpretation of actual trends in the presence of any underlying climate change. Here, a simple technique to remove the inherent trend is introduced so that any remaining trend can be examined separately for evidence of a climate change. As this technique does not use the standard definition of a broken record, our records* are differentiated by an asterisk. Results for the period 1961-2010 indicate that the number of record* low daily minimum temperatures has been significantly and steadily decreasing nearly everywhere across the United States while the number of record* high daily minimum temperatures has been predominantly increasing. Trends in record* low and record* high daily maximum temperatures are generally weaker and more spatially mixed in sign. These results are consistent with other studies examining changes expected in a warming climate.

Effect of strain of layer and age at photostimulation on egg production, egg quality, and bone strength.

PubMed

Silversides, F G; Korver, D R; Budgell, K L

2006-07-01

Bone strength in layers is a concern for economic reasons and animal welfare concerns. Bone characteristics were investigated in 3 strains of hens: Babcock B-300, a small-bodied commercial white-egg layer; ISA-Brown, a commercial brown-egg layer; and an unselected Brown Leghorn line (BL). After being reared together in a single pen with 8 h of light per day, hens were caged with 14 h of light per day. Half of the hens were caged at 18 wk of age and the other half at 20 wk of age, resulting in a 2-wk difference in the age at photostimulation. Body weights, egg production, feed efficiency, and egg quality were measured throughout production. At 15, 25, 50, and 74 wk of age, hens were euthanized for sampling of the radius and the humerus. Breaking strength of the radius and humerus was measured, and the area and density of trabecular (largely medullary bone) and cortical bone were measured using quantitative computed tomography. Egg production and feed conversion of ISA-Brown hens was as good as or better than that of Babcock B-300 hens, and both commercial strains had higher production than the BL. Photostimulation late delayed sexual maturity and improved albumen and shell characteristics but had only minor effects on egg production and did not affect the yolk weight. The delayed photostimulation resulting from caging 2 wk later affected the radius by increasing the area of the trabecular space at 50 wk of age and the density of the bone in the trabecular space at 74 wk of age. Breaking strength of the humerus at 25 wk of age was greater for the birds that were photostimulated late but was not different later in the trial. The humerus, but not the radius, of the BL had a greater breaking strength than that of the commercial strains, suggesting that selection has decreased humeral breaking strength.

Tensile strength and impact resistance properties of materials used in prosthetic check sockets, copolymer sockets, and definitive laminated sockets.

PubMed

Gerschutz, Maria J; Haynes, Michael L; Nixon, Derek M; Colvin, James M

2011-01-01

Prosthetic sockets serve as the interface between people with amputations and their prostheses. Although most materials used to make prosthetic sockets have been used for many years, knowledge of these materials' properties is limited, especially after they are subjected to fabrication processes. This study evaluated tensile and impact properties of the current state-of-the-art materials used to fabricate prosthetic check sockets, copolymer sockets, and definitive laminated sockets. Thermolyn Rigid and Orfitrans Stiff check socket materials produced significantly lower tensile strength and impact resistance than polyethylene terephthalate glycol (PETG). Copolymer socket materials exhibited greater resistance to impact forces than the check socket materials but lower tensile strengths than PETG. The heated molding processes, for the check socket and copolymer materials, reduced both tensile strength and elongation at break. Definitive laminated sockets were sorted according to fabrication techniques. Nyglass material had significantly higher elongation, indicating a more ductile material than carbon-based laminations. Carbon sockets with pigmented resin had higher tensile strength and modulus at break than nonpigmented carbon sockets. Elongation at yield and elongation at break were similar for both types of carbon-based laminations. The material properties determined in this study provide a foundation for understanding and improving the quality of prosthetic sockets using current fabrication materials and a basis for evaluating future technologies.

Chain Ends and the Ultimate Tensile Strength of Polyethylene Fibers

NASA Astrophysics Data System (ADS)

O'Connor, Thomas C.; Robbins, Mark O.

Determining the tensile yield mechanisms of oriented polymer fibers remains a challenging problem in polymer mechanics. By maximizing the alignment and crystallinity of polyethylene (PE) fibers, tensile strengths σ ~ 6 - 7 GPa have been achieved. While impressive, first-principal calculations predict carbon backbone bonds would allow strengths four times higher (σ ~ 20 GPa) before breaking. The reduction in strength is caused by crystal defects like chain ends, which allow fibers to yield by chain slip in addition to bond breaking. We use large scale molecular dynamics (MD) simulations to determine the tensile yield mechanism of orthorhombic PE crystals with finite chains spanning 102 -104 carbons in length. The yield stress σy saturates for long chains at ~ 6 . 3 GPa, agreeing well with experiments. Chains do not break but always yield by slip, after nucleation of 1D dislocations at chain ends. Dislocations are accurately described by a Frenkel-Kontorova model, parametrized by the mechanical properties of an ideal crystal. We compute a dislocation core size ξ = 25 . 24 Å and determine the high and low strain rate limits of σy. Our results suggest characterizing such 1D dislocations is an efficient method for predicting fiber strength. This research was performed within the Center for Materials in Extreme Dynamic Environments (CMEDE) under the Hopkins Extreme Materials Institute at Johns Hopkins University. Financial support was provided by Grant W911NF-12-2-0022.

Theoretical investigations into the influence of the position of a breaking line on the tensile failure of flat, round, bevel-edged tablets using finite element methodology (FEM) and its practical relevance for industrial tablet strength testing.

PubMed

Podczeck, Fridrun; Newton, J Michael; Fromme, Paul

2014-12-30

Flat, round tablets may have a breaking ("score") line. Pharmacopoeial tablet breaking load tests are diametral in their design, and industrially used breaking load testers often have automatic tablet feeding systems, which position the tablets between the loading platens of the machine with the breaking lines in random orientation to the applied load. The aim of this work was to ascertain the influence of the position of the breaking line in a diametral compression test using finite element methodology (FEM) and to compare the theoretical results with practical findings using commercially produced bevel-edged, scored tablets. Breaking line test positions at an angle of 0°, 22.5°, 45°, 67.5° and 90° relative to the loading plane were studied. FEM results obtained for fully elastic and elasto-plastic tablets were fairly similar, but they highlighted large differences in stress distributions depending on the position of the breaking line. The stress values at failure were predicted to be similar for tablets tested at an angle of 45° or above, whereas at lower test angles the predicted breaking loads were up to three times larger. The stress distributions suggested that not all breaking line angles would result in clean tensile failure. Practical results, however, did not confirm the differences in the predicted breaking loads, but they confirmed differences in the way tablets broke. The results suggest that it is not advisable to convert breaking loads obtained on scored tablets into tablet tensile strength values, and comparisons between different tablets or batches should carefully consider the orientation of the breaking line with respect to the loading plane, as the failure mechanisms appear to vary. Copyright © 2014 Elsevier B.V. All rights reserved.

A comparison of the reliability of make versus break testing in measuring palmar abduction strength of the thumb.

PubMed

Lim, J X; Toh, R X; Chook, S K H; Sebastin, S J; Karjalainen, T

2014-06-01

Previous studies have established the role of quantitative measurements of palmar abduction strength of the thumb (PAST). This study compares the reliability of the 'make' versus the 'break' test in measuring PAST in healthy volunteers. In a 'make' test, the body part being tested is positioned at the start of its range of motion and the participant is asked to exert his/her maximal force. In a 'break' test, increasing force is applied to a body part after it has completed its range of motion, until the joint being tested gives way. PAST was measured in both hands in 100 healthy volunteers using a handheld device. Two examiners measured PAST using both the 'make' and 'break' test to determine inter-rater reliability. The tests were repeated in 30 volunteers 6 weeks after the initial testing to determine intra-rater reliability. Our results showed that the 'make' test has better inter and intra-rater reliability.

Dynamic Breaking Tests of Airplane Parts

NASA Technical Reports Server (NTRS)

Hertel, Heinrich

1933-01-01

The static stresses of airplane parts, the magnitude of which can be determined with the aid of static load assumptions, are mostly superposed by dynamic stresses, the magnitude of which has been but little explored. The object of the present investigation is to show how the strength of airplane parts can best be tested with respect to dynamic stresses with and without superposed static loading, and to what extent the dynamic strength of the parts depends on their structural design. Experimental apparatus and evaluation methods were developed and tried for the execution of vibration-strength tests with entire structural parts both with and without superposed static loading. Altogether ten metal spars and spar pieces and two wooden spars were subjected to vibration breaking tests.

Variability and interaction of some egg physical and eggshell quality attributes during the entire laying hen cycle.

PubMed

Sirri, F; Zampiga, M; Berardinelli, A; Meluzzi, A

2018-05-01

The aim of this study was to investigate the variability and relationships between some egg physical (egg weight, width, length, shape index, and surface area) and eggshell parameters (weight and percentage, thickness, breaking strength, and L*, a*, and b* values) during the entire laying hen cycle. A total of 8,000 eggs was collected every 5 wk, from 30 to 81 wk of hen age (10 samplings of 400 eggs/house), in 2 identical poultry houses equipped with enriched cages. For the statistical analysis, ANOVA, Bivariate Correlation, Principal Component Analysis (PCA), and Hierarchical Cluster Analysis were used. An increase of egg weight, length, and eggshell lightness (L*) associated with a reduction of eggshell percentage, breaking strength, and redness (a*) was observed as the hen aged (P < 0.05). Overall, the coefficients of variation resulted in <5% in width, length, shape index, and egg surface area; from 5 to 10% of egg weight, shell weight, shell percentage, shell thickness, L*, and b*; and >10% of eggshell breaking strength and a*. According to the PCA, the highest changes during the laying cycle are related to egg physical parameters (32%) and to eggshell breaking strength, percentage, and thickness (26%). The egg physical parameters appeared to be strongly correlated to each other, whereas a slight correlation between eggshell breaking strength and color attributes were evidenced (-0.231 and 0.289, respectively, for L* and a*; P < 0.01). Hierarchical cluster analysis, based on principal components of the overall egg attributes, is hereby considered, and evidenced dissimilarities for eggs laid from peak production up for 39 wk of hen age from the eggs laid afterwards. The latter group could also be divided into 2 subgroups, one comprising eggs laid from 44 and 53 wk of hen age and the other from 58 wk to the end. In conclusion, the large dataset created in this study allowed to extrapolate some robust information regarding the variability and correlations of the egg physical and eggshell quality attributes throughout the entire laying hen cycle.

49 CFR 238.230 - Safety appliances-new equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... a minimum weld strength, based on yield, of three times the strength of the number of SAE grade 2, 1...; (v) The weld is designed for infinite fatigue life in the application that it will be placed; (vi... upon request. At a minimum, this record shall include the date, time, location, identification of the...

49 CFR 195.306 - Test medium.

Code of Federal Regulations, 2010 CFR

2010-10-01

... which produces a hoop stress of 50 percent of specified minimum yield strength; (3) The test section is... pressure is equal to or greater than a pressure that produces a hoop stress of 50 percent of specified minimum yield strength; (3) The maximum hoop stress during the test does not exceed 80 percent of...

49 CFR 195.306 - Test medium.

Code of Federal Regulations, 2012 CFR

2012-10-01

... which produces a hoop stress of 50 percent of specified minimum yield strength; (3) The test section is... pressure is equal to or greater than a pressure that produces a hoop stress of 50 percent of specified minimum yield strength; (3) The maximum hoop stress during the test does not exceed 80 percent of...

29 CFR 1926.752 - Site layout, site-specific erection plan and construction sequence.

Code of Federal Regulations, 2011 CFR

2011-07-01

... standard test method of field-cured samples, either 75 percent of the intended minimum compressive design... the basis of an appropriate ASTM standard test method of field-cured samples, either 75 percent of the intended minimum compressive design strength or sufficient strength to support the loads imposed during...

29 CFR 1926.752 - Site layout, site-specific erection plan and construction sequence.

Code of Federal Regulations, 2013 CFR

2013-07-01

... standard test method of field-cured samples, either 75 percent of the intended minimum compressive design... the basis of an appropriate ASTM standard test method of field-cured samples, either 75 percent of the intended minimum compressive design strength or sufficient strength to support the loads imposed during...

29 CFR 1926.752 - Site layout, site-specific erection plan and construction sequence.

Code of Federal Regulations, 2012 CFR

2012-07-01

... standard test method of field-cured samples, either 75 percent of the intended minimum compressive design... the basis of an appropriate ASTM standard test method of field-cured samples, either 75 percent of the intended minimum compressive design strength or sufficient strength to support the loads imposed during...

29 CFR 1926.752 - Site layout, site-specific erection plan and construction sequence.

Code of Federal Regulations, 2010 CFR

2010-07-01

... standard test method of field-cured samples, either 75 percent of the intended minimum compressive design... the basis of an appropriate ASTM standard test method of field-cured samples, either 75 percent of the intended minimum compressive design strength or sufficient strength to support the loads imposed during...

29 CFR 1926.752 - Site layout, site-specific erection plan and construction sequence.

Code of Federal Regulations, 2014 CFR

2014-07-01

... standard test method of field-cured samples, either 75 percent of the intended minimum compressive design... the basis of an appropriate ASTM standard test method of field-cured samples, either 75 percent of the intended minimum compressive design strength or sufficient strength to support the loads imposed during...

Evaluation of Bone Strength During Aflatoxicosis and Ochratoxicosis †

PubMed Central

Huff, William E.; Doerr, John A.; Hamilton, Pat B.; Hamann, Donald D.; Peterson, Robert E.; Ciegler, Alex

1980-01-01

Young chickens were fed graded levels of aflatoxin (0, 0.625, 1.25, 2.5, 5.0, and 10.0 μg/g of diet) or ochratoxin (0, 0.5, 1.0, 2.0, 4.0, and 8.0 μg/g of diet), and the breaking strength, displacement before failure, and diameter of their tibias were determined. Breaking strength was decreased at growth inhibitory levels of aflatoxin (2.5 μg/g) and ochratoxin (2 μg/g), whereas a reduction in diameter required higher levels (5.0 and 4.0 μg/g, respectively). Bones from birds with ochratoxicosis selected to have diameters equal to control bones had lower breaking strength. In an attempt to negate mathematically the effect of decreased diameter and bias in any selection process, stress at time of failure of the bones was calculated and found to be decreased by feeding aflatoxin but not ochratoxin. Total displacement of bones before breaking was increased significantly (P < 0.05) by both toxins at the highest levels administered, but this increase was primarily the result of an increase in displacement from the start of failure to complete failure. Increased displacement associated with both toxicoses was equal in bones selected to be of equal diameter or in bones from the same treatment but of different diameters. However, calculation of modulus of elasticity which is corrected for diameter revealed aflatoxin had no effect whereas ochratoxin tripled the effect. These data indicate that the material properties of bones can be altered during mycotoxicoses and suggest yet another way in which mycotoxins are detrimental to animal health. PMID:7406489

Study on mechanical and ablative properties of EPDM/OMMT thermal insulating nanocomposites.

PubMed

Gao, Guoxin; Zhang, Zhicheng; Li, Xuefei; Meng, Qingjie; Zheng, Yuansuo; Jin, Zhihao

2010-11-01

In order to enhance the elongation at break, the ablation resistant properties as well as the tensile strength of the thermal insulating materials, organo-montmorillonite (OMMT) was introduced into the short aramid fibers reinforced Ethylene-Propylene-Diene Monomer (EPDM) based nanocomposites. The effects of OMMT content on the mechanical and ablative properties of the nanocomposites were investigated systematically. X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirm that EPDM-matrix has been intercalated into OMMT interlayers after a mixing process on a two-roll mill. The brittle fracture of nanocomposites also indicates that OMMT can lubricate aramid fiber to weaken the interfacial adhesive strength between the fibers and the matrix. As a result, the tensile strength and elongation at break are both improved sharply with OMMT content increasing from 1 phr to 7 phr. However, thanks to the inevitable agglomeration of OMMT with high loading inside the nanocomposites, the tensile strength and elongation at break reduce gently once OMMT is over 7 phr. Furthermore, the ablation resistant properties are improved greatly by increasing OMMT from 1 phr to 11 phr. Therefore, the optimal content of OMMT is 7-11 phr for the thermal insulating nanocomposites with big elongation and excellent ablation resistant properties.

Preparation and mechanical properties of rubber composites reinforced with carbon nanohorns.

PubMed

Isshiki, Tetsuya; Hashimoto, Mikiko; Morii, Masato; Ota, Yuki; Kaneda, Kazuo; Takahashi, Hidetaka; Yudasaka, Masako; Iijima, Sumio; Okino, Fujio

2010-06-01

Nitrile butadiene rubber (NBR) composites with single-wall carbon nanohorns (SWNHs, or simply NHs), hole-opened NHs (h-NHs), and carbon black (CB), the most commonly used nanocarbon rubber filler, were prepared, and their mechanical properties were compared. The NBR composites with h-NHs (NBR/h-NH) showed higher tensile strength than those with NHs (NBR/NH), and the tensile strength of NBR/h-NH or NBR/NH was much greater than those of the NBR composites with CB (NBR/CB). At 5 parts per hundred of rubber (phr), the tensile stresses at break of NBR/h-NH was about 1.8 times larger than those of NBR/CB, and the strain at the break, 1.2 times larger. Similarly, at 20 phr, both the tensile strength and strain at the break of NBR/h-NH were 1.4 times larger than those of NBR/CB. NBR/NH showed the highest hardness while having the smallest specific gravity. The present results indicate that NHs and h-NHs have much superior reinforcement effects to CB for NBR rubber matrix.

Mechanical strength of laser-welded cobalt-chromium alloy.

PubMed

Baba, N; Watanabe, I; Liu, J; Atsuta, M

2004-05-15

The purpose of this study was to investigate the effect of the output energy of laser welding and welding methods on the joint strength of cobalt-chromium (Co-Cr) alloy. Two types of cast Co-Cr plates were prepared, and transverse sections were made at the center of the plate. The cut surfaces were butted against one another, and the joints welded with a laser-welding machine at several levels of output energy with the use of two methods. The fracture force required to break specimens was determined by means of tensile testing. For the 0.5-mm-thick specimens, the force required to break the 0.5-mm laser-welded specimens at currents of 270 and 300 A was not statistically different (p > 0.05) from the results for the nonwelded control specimens. The force required to break the 1.0-mm specimens double-welded at a current of 270 A was the highest value among the 1.0-mm laser-welded specimens. The results suggested that laser welding under the appropriate conditions improved the joint strength of cobalt- chromium alloy. Copyright 2004 Wiley Periodicals, Inc.

Effect of Kevlar and carbon fibres on tensile properties of oil palm/epoxy composites

NASA Astrophysics Data System (ADS)

Amir, S. M. M.; Sultan, M. T. H.; Jawaid, M.; Cardona, F.; Ishak, M. R.; Yusof, M. R.

2017-12-01

Hybrid composites with natural and synthetic fibers have captured the interests of many researchers. In this work, Kevlar/oil palm Empty Fruit Bunch (EFB)/Kevlar and carbon/oil palm EFB hybrid/carbon composites were prepared using hand lay-up technique by keeping the oil palm EFB fiber as the core material. The tensile properties which include tensile strength, tensile modulus and elongation at break were investigated. It is observed that the tensile strength and modulus for carbon/oil palm EFB/carbon hybrid composites were much higher as compared with Kevlar/oil palm EFB/Kevlar hybrid composites. However, the elongation at break for Kevlar/oil palm EFB/Kevlar hybrid composites exhibited higher value as compared to carbon/oil palm EFB/carbon hybrid composites and oil palm EFB/epoxy composites. The tensile strength for carbon/oil palm EFB/carbon hybrid composites is 93.6 MPa and the tensile modulus for carbon/oil palm EFB/carbon hybrid composites is 6.5 GPa. The elongation at break for Kevlar/oil palm EFB/Kevlar hybrid composites is 3.6%.

A comparison of lateral ankle ligament suture anchor strength.

PubMed

Barber, F Alan; Herbert, Morley A; Crates, John M

2013-06-01

Lateral ankle ligament repairs increasingly use suture anchors instead of bone tunnels. Our purpose was to compare the biomechanical properties of a knotted and knotless suture anchor appropriate for a lateral ankle ligament reconstruction. In porcine distal fibulae, 10 samples of 2 different PEEK anchors were inserted. The attached sutures were cyclically loaded between 10N and 60N for 200 cycles. A destructive pull was performed and failure loads, cyclic displacement, stiffness, and failure mode recorded. PushLock 2.5 anchors failed before 200 cycles. PushLock 100 cycle displacement was less than Morphix 2.5 displacement (p<0.001). Ultimate failure load for anchors completing 200 cycles was 86.5N (PushLock) and 252.1N (Morphix) (p<0.05). The failure mode was suture breaking for all PushLocks while the Morphix failed equally by anchor breaking and suture breakage. The knotted Morphix demonstrated more displacement and greater failure strength than the knotless PushLock. The PushLock failed consistently with suture breaking. The Morphix anchor failed both by anchor breaking and by suture breaking. Copyright © 2012 European Foot and Ankle Society. Published by Elsevier Ltd. All rights reserved.

In Vitro Tensile Strength Study on Suturing Technique and Material.

PubMed

González-Barnadas, Albert; Camps-Font, Octavi; Espanya-Grifoll, Dunia; España-Tost, Antoni; Figueiredo, Rui; Valmaseda-Castellón, Eduard

2017-06-01

Suture technique and materials are important in preventing complications such as wound dehiscences. The purpose of this study was to determine the tensile strength of different suturing techniques, comparing several materials with different diameters. One hundred sixty sutures were performed using silk, e-PTFE, and 2 types of polyamide (monofilament and Supramid). Ten simple, 10 horizontal mattress, and 10 combinations of the two stitches were performed with 4-0 gauge of each material. Additionally, 10 simple sutures were performed with the 5-0 gauge of each material. The maximum tensile force resisted by each suture was recorded. When 5 mm of traction was applied, the polyamide monofilament resisted significantly better without untying or breaking compared with Supramid or silk, while the e-PTFE was superior to all the others. However, the force when e-PTFE 4-0 sutures untied or broke was lower than for either type of polyamide. The combined technique withstood a significantly higher tensile force before unknotting or breaking than did the simple and mattress stitches. The 5-0 gauges of silk and both types of polyamide showed lower tensile strengths than the 4-0 materials. Among the 5-0 sutures, Supramid showed a higher tensile strength than silk. The combined suture technique possessed greater tensile strength than did a simple or a horizontal mattress suture, and e-PTFE 4-0 withstood more traction without untying or breaking than did all the other materials, although at a lower tensile force. With the exception of e-PTFE, 4-0 sutures had greater tensile strength than did 5-0 sutures.

Studies on crosslinked hydroxyapatite-polyethylene composite as a bone-analogue material

NASA Astrophysics Data System (ADS)

Smolko, E.; Romero, G.

2007-08-01

The paper examines the use of different types of polymeric matrix composites in hard-tissue replacement applications. The composite samples were prepared with hydroxyapatite (HA) powder and polyethylenes of different densities. The raw material was first compounded in the extruder and the resulting composite pre-forms were compression molded into desired plates and irradiated with different doses. Modulus of elasticity in tension, tensile strength, tensile fracture strain, elongation at break and gel content were obtained for all composites. Ceramic filler distribution was investigated under scanning electron microscopy (SEM). With HA incorporated in the samples an increase in the values of Young's Modulus, (stiffness) was observed, while elongation at break decreased with the amount of filler, showing increase of brittleness. Tensile strengths at yield and at break decreased with the filler content for LD and MDPE and stayed constant for HDPE.

Compressive residual strength of graphite/epoxy laminates after impact

NASA Technical Reports Server (NTRS)

Guy, Teresa A.; Lagace, Paul A.

1992-01-01

The issue of damage tolerance after impact, in terms of the compressive residual strength, was experimentally examined in graphite/epoxy laminates using Hercules AS4/3501-6 in a (+ or - 45/0)(sub 2S) configuration. Three different impactor masses were used at various velocities and the resultant damage measured via a number of nondestructive and destructive techniques. Specimens were then tested to failure under uniaxial compression. The results clearly show that a minimum compressive residual strength exists which is below the open hole strength for a hole of the same diameter as the impactor. Increases in velocity beyond the point of minimum strength cause a difference in the damage produced and cause a resultant increase in the compressive residual strength which asymptotes to the open hole strength value. Furthermore, the results show that this minimum compressive residual strength value is independent of the impactor mass used and is only dependent upon the damage present in the impacted specimen which is the same for the three impactor mass cases. A full 3-D representation of the damage is obtained through the various techniques. Only this 3-D representation can properly characterize the damage state that causes the resultant residual strength. Assessment of the state-of-the-art in predictive analysis capabilities shows a need to further develop techniques based on the 3-D damage state that exists. In addition, the need for damage 'metrics' is clearly indicated.

Fiber length - fiber strength interrelationship for slash pine and its effect on pulp-sheet properties

Treesearch

F.F. Wangaard; George E. Woodson

1972-01-01

Based on a model developed for hardwood fiber strength-pulp property relationships, multiple-regression equations involving fiber strength, fiber length, and sheet density were determined to predict the properties of kraft pulps of slash pine (Pinus elliottii). Regressions for breaking length and burst factor accounted for 88 and 90 percent,...

Fiber length strength interrelationship for slash pine and its effect on pulp-sheet properties

Treesearch

F. G. Wangaard; G. E. Woodson

1973-01-01

Based on a model developed for hardwood fiber strength-pulp property relationships, multiple-regression equations involving fiber strength, fiber length, and sheet density were determined to predict the properties of kraft pulps of slash pine (Pinus elliottii). Regressions for breaking length and burst factor accounted for 88 and 90 percent,...

Frequency of effective wave activity and the recession of coastal bluffs: Calvert Cliffs, Maryland

USGS Publications Warehouse

Wilcock, P.R.; Miller, D.S.; Shea, R.H.; Kerkin, R.T.

1998-01-01

The Calvert Cliffs, Chesapeake Bay, Maryland, USA, erode by direct wave undercutting or by freeze/thaw erosion accompanied by wave removal of slope debris. Directly undercut slopes recede more rapidly, with long-term rates exceeding 1.0 m/yr; freeze/thaw slopes recede at rates approaching 0.5 m/yr. The frequency of wave height and water level at the shoreline is estimated for eleven sites based on a 37-year wind record, estimates of storm surge, offshore wave geometry, nearshore wave transformation, and breaking wave type. Locations experiencing the largest slope recession are not uniformly those with the largest cumulative wave energy; the resistance to erosion of the slope toe must also be accounted for. An index of relative wave strength is defined as the ratio of wave pressure T and the cohesive strength S of the slope material. For the Calvert Cliffs, a minimum relative wave strength for initiating erosion of intact material is 0.05 < T/S < 0.1. A cumulative duration of ???50 hours per year for T/S ??? 0.1 distinguishes undercut and nonundercut slopes and recession rates greater or lesser than 0.5 m/yr. The relative wave strength index may be used to identify sites at risk of increased erosion. At one site with a small historical erosion rate, the loss of a protective beach and associated decrease in toe elevation caused a positive shift in the frequency of large T/S. Direct wave undercutting and increased slope recession may be anticipated at this site, as indicated by the development of an undercut notch during the course of the study.

Solar-Cycle Variability of Magnetosheath Fluctuations at Earth and Venus

NASA Astrophysics Data System (ADS)

Dwivedi, N. K.; Narita, Y.; Kovacs, P.

2014-12-01

The magnetosheath is a region between the bow-shock and magnetopause and the magnetosheath plasma is mostly in the turbulent state. In the present investigation we put an effort to closely examine the magnetosheath fluctuations dependency on the solar-cycles (solar-maximum and solar minimum) at the magnetized planetary body (Earth) and their comparison with the un-magnetized planetary body (Venus) for the solar minimum. We use the CLUSTER FGM data for the solar-maximum (2001-2002), solar-minimum (2006-2008) and Venus fluxgate magnetometer data for the solar-minimum (2006-2008) to perform a comparative statistical study on the energy spectra and probability density function (PDF) and asses the spectral features of the magnetic fluctuations of the both planetary bodies. In the comparison we study the relation between the inertial ranges of the spectra and the temporal scales of non-Gaussian magnetic fluctuations derived from PDF analyses. The first can refer to turbulent cascade dynamics, while the latter may indicate intermittency. We first transformed the magnetic field data into mean field aligned coordinate system with respect to the large-scale magnetic field direction and then after we compute the power spectral density with the help of Welch algorithm. The computed energy spectra of Earth's magnetosheath show a moderate variability with the solar-cycles and have a broader inertial range. However the estimated energy spectra for the solar-minimum at Venus give the clear evidence of the existence of the break point in the vicinity of the ion gyroradius. After the break-point the energy spectra become steeper and show a distinctive spectral scales which is interpreted as the realization of the begging of the energy cascade. We also briefly address the influence of turbulence on the plasma transport and wave dynamics responsible for the spectral break and predict spectral features of the energy spectra for the solar-maximum at Venus based on the results obtained for the solar-minimum. The research leading to these results has received funding from the European Community's Seventh Framework Programme ([FP7/2007-2013]) under grant agreement number 313038/STORM.

An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends.

PubMed

Ahmed, Khalil

2015-11-01

Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE) compatibilized by Chloroprene rubber (CR) were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr) was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (M L) and maximum torque (M H) of blends increased with increasing weight ratio of HDPE while scorch time (ts2) cure time (tc90), compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties.

An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends

PubMed Central

Ahmed, Khalil

2014-01-01

Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE) compatibilized by Chloroprene rubber (CR) were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr) was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (ML) and maximum torque (MH) of blends increased with increasing weight ratio of HDPE while scorch time (ts2) cure time (tc90), compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties. PMID:26644917

An improved device to measure cottonseed strength

USDA-ARS?s Scientific Manuscript database

During processing, seeds of cotton cultivars with fragile seeds often break and produce seed coat fragments that can cause processing problems at textile mills. A cottonseed shear tester, previously developed to measure cottonseed strength, was modified with enhancements to the drive system to provi...

Using Appreciative Intelligence for Ice-Breaking: A New Design

ERIC Educational Resources Information Center

Verma, Neena; Pathak, Anil Anand

2011-01-01

Purpose: The purpose of this paper is to highlight the importance of applying appreciative intelligence and appreciative inquiry concepts to design a possibly new model of ice-breaking, which is strengths-based and very often used in any training in general and team building training in particular. Design/methodology/approach: The design has…

Characterization of silver nanoparticle-infused tissue adhesive for ophthalmic use.

PubMed

Yee, William; Selvaduray, Guna; Hawkins, Benjamin

2015-03-01

In this work, we demonstrate the successful enhancement of breaking strength, adhesive strength, and antibacterial efficacy of ophthalmic tissue adhesive (2-octyl cyanoacrylate) by doping with silver nanoparticles, and investigate the effects of nanoparticle size and concentration. Recent work has shown that silver nanoparticles are a viable antibacterial additive to many compounds, but their efficacy in tissue adhesives was heretofore untested. Our results indicate that doping the adhesive with silver nanoparticles reduced bacterial growth by an order of magnitude or more; nanoparticle size and concentration had minimal influence in the range tested. Tensile breaking strength of polymerized adhesive samples and adhesive strength between a T-shaped support and excised porcine sclera were measured using a universal testing machine according to ASTM (formerly American Society for Testing and Materials) standard techniques. Both tests showed significant improvement with the addition of silver nanoparticles. The enhanced mechanical strength and antibacterial efficacy of the doped adhesive supports the use of tissue adhesives as a viable supplement or alternative to sutures. Copyright © 2015 Elsevier Ltd. All rights reserved.

Quantum anharmonic oscillator plus delta-function potential: a molecular view of pairing formation and breaking in the coordinate space

NASA Astrophysics Data System (ADS)

Sumaryada, Tony; Maha Putra, Bima; Pramudito, Sidikrubadi

2017-05-01

We propose an alternative way to describe the pairing formation and breaking via a quantum anharmonic oscillator with a delta-function potential model. Unlike BCS theory, which describes the pairing formation in the momentum space, this model works in the coordinate space and is able to give a molecular view of pairing formation and breaking in the coordinate space. By exploring the dynamical interplay between the intrinsic factor (dissociation energy) and external factor (pairing strength) of this system additional information was gained, including the critical pairing strength and critical scattering length, which might relate to the BCS-BEC crossover phenomena and halo state formation. Although only the energetic aspect of pairing is described by this model, its simplicity and pedagogical steps might help undergraduate students to understand the pairing problem in a simple way.

Magnetic fields in Supernova Remnants and Pulsar-Wind Nebulae: Deductions from X-ray Observations

NASA Astrophysics Data System (ADS)

Reynolds, S. P.

2016-06-01

Magnetic field strengths B in synchrotron sources are notoriously difficult to measure. Simple arguments such as equipartition of energy can give values for which the total energy is a minimum, but there is no guarantee that Nature obeys it, or even if so, what particle population (just electrons? electrons plus ions?) should have an energy density comparable to that in magnetic field. However, the operation of synchrotron losses can provide additional information, if those losses are manifested in the synchrotron spectra as steepenings of the spectral-energy distribution above some characteristic frequency often called a "break" (though it is more typically a gradual curvature). A source of known age, if it has been accelerating particles continuously, will have such a break above the energy at which particle radiative lifetimes equal the source age, and this can give B. However, in spatially resolved sources such as supernova remnants (SNRs) and pulsar-wind nebulae (PWNe), systematic advection of particles, if at a known rate, gives a second measure of particle age to compare with radiative lifetimes. In most young SNRs, synchrotron X-rays make a contribution to the X-ray spectrum, and are usually found in thin rims at the remnant edges. If the rims are thin in the radial direction due to electron energy losses, a magnetic-field strength can be estimated. I present recent modeling of this process, along with models in which rims are thin due to decay of magnetic turbulence, and apply them to the remnants of SN 1006 and Tycho. In PWNe, outflows of relativistic plasma behind the pulsar wind termination shock are likely quite inhomogeneous, so magnetic-field estimates based on source lifetimes and assuming spatial uniformity can give misleading values for B. I shall discuss inhomogeneous PWN models and the effects they can have on B estimates.

Tough silk fibers prepared in air using a biomimetic microfluidic chip.

PubMed

Luo, Jie; Zhang, Lele; Peng, Qingfa; Sun, Mengjie; Zhang, Yaopeng; Shao, Huili; Hu, Xuechao

2014-05-01

Microfluidic chips with single channel were built to mimic the shear and elongation conditions in the spinning apparatus of spider and silkworm. Silk fibers dry-spun from regenerated silk fibroin (RSF) aqueous solution using the chip could be tougher than degummed natural silk. The artificial silk exhibited a breaking strength up to 614 MPa, a breaking elongation up to 27% and a breaking energy of 101 kJ/kg. Copyright © 2014 Elsevier B.V. All rights reserved.

46 CFR 160.176-4 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

... and Elongation, Breaking of Woven Cloth; Grab Method, incorporation by reference approved for § 160.176-13. (ii) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method, incorporation by reference approved for § 160.176-13. (iii) Method 5134, Strength of Cloth, Tearing; Tongue Method...

46 CFR 160.176-4 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

... and Elongation, Breaking of Woven Cloth; Grab Method, incorporation by reference approved for § 160.176-13. (ii) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method, incorporation by reference approved for § 160.176-13. (iii) Method 5134, Strength of Cloth, Tearing; Tongue Method...

46 CFR 160.077-5 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., Breaking of Woven Cloth; Grab Method. (ii) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method. (iii) Method 5134, Strength of Cloth, Tearing; Tongue Method. (iv) Method 5804.1, Weathering Resistance of Cloth; Accelerated Weathering Method. (v) Method 5762, Mildew Resistance of Textile Materials...

46 CFR 160.077-5 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Elongation, Breaking of Woven Cloth; Grab Method. (2) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method. (3) Method 5134, Strength of Cloth, Tearing; Tongue Method. (4) Method 5804.1, Weathering Resistance of Cloth; Accelerated Weathering Method. (5) Method 5762, Mildew Resistance of Textile Materials...

46 CFR 160.077-5 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., Breaking of Woven Cloth; Grab Method. (ii) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method. (iii) Method 5134, Strength of Cloth, Tearing; Tongue Method. (iv) Method 5804.1, Weathering Resistance of Cloth; Accelerated Weathering Method. (v) Method 5762, Mildew Resistance of Textile Materials...

46 CFR 160.077-5 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Elongation, Breaking of Woven Cloth; Grab Method. (2) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method. (3) Method 5134, Strength of Cloth, Tearing; Tongue Method. (4) Method 5804.1, Weathering Resistance of Cloth; Accelerated Weathering Method. (5) Method 5762, Mildew Resistance of Textile Materials...

Evaluation of aqueous leaves extract of Moringa oleifera Linn for wound healing in albino rats.

PubMed

Rathi, B S; Bodhankar, S L; Baheti, A M

2006-11-01

Aqueous extract of leaves of M. oleifera was investigated and rationalised for its wound healing activity. The aqueous extract was studied at dose level of 300 mg/kg body weight using resutured incision; excision and dead space wound models in rats. Significant increase in wound closure rate, skin-breaking strength, granuloma breaking strength, hydroxyproline content, granuloma dry weight and decrease in scar area was observed. The prohealing actions seem to be due to increased collagen deposition as well as better alignment and maturation. From the results obtained, it may be concluded that the aqueous extract of M. oleifera has significant wound healing property.

Influence of different crosslinking systems on the mechanical and morphological properties of thermoplastic vulcanizates

NASA Astrophysics Data System (ADS)

Patermann, Simone; Altstädt, Volker

2015-05-01

Thermoplastic vulcanizates (TPVs) combine the elastic properties of thermoset cross-linked rubbers with the melt processability of thermoplastics. The most representative examples of this class are the TPVs based on polypropylene (PP) and ethylene-propylene-diene terpolymer rubber (EPDM). The PP/EPDM blends were produced by dynamic vulcanization in a continuous extrusion process. The influence of different crosslinking systems was studied with regard to cross-link density, compression set, tensile strength/elongation at break and morphology. With increasing peroxide concentration, the cross-link density increases, leading to a reduction of the compression set by 50 %. The same improvement is only reachable with twice the concentration of phenolic resin. Only the peroxide cross-linked blends show smaller dispersed EPDM particles with increasing peroxide concentration. With a peroxide concentration between 0.2 and 0.5 wt. %, a maximum in tensile strength and elongation at break was found. For the phenolic resin cross-linked blends, the tensile strength stays almost constant with increasing phenolic resin concentration and the elongation at break shows best results at 0.5 wt. % phenolic resin. Compared to batch processes, the results show different values, but comparable trends.

A stochastic model for soft tissue failure using acoustic emission data.

PubMed

Sánchez-Molina, D; Martínez-González, E; Velázquez-Ameijide, J; Llumà, J; Rebollo Soria, M C; Arregui-Dalmases, C

2015-11-01

The strength of soft tissues is due mainly to collagen fibers. In most collagenous tissues, the arrangement of the fibers is random, but has preferred directions. The random arrangement makes it difficult to make deterministic predictions about the starting process of fiber breaking under tension. When subjected to tensile stress the fibers are progressively straighten out and then start to be stretched. At the beginning of fiber breaking, some of the fibers reach their maximum tensile strength and break down while some others remain unstressed (this latter fibers will assume then bigger stress until they eventually arrive to their failure point). In this study, a sample of human esophagi was subjected to a tensile breaking of fibers, up to the complete failure of the specimen. An experimental setup using Acoustic Emission to detect the elastic energy released is used during the test to detect the location of the emissions and the number of micro-failures per time unit. The data were statistically analyzed in order to be compared to a stochastic model which relates the level of stress in the tissue and the probability of breaking given the number of previously broken fibers (i.e. the deterioration in the tissue). The probability of a fiber breaking as the stretch increases in the tissue can be represented by a non-homogeneous Markov process which is the basis of the stochastic model proposed. This paper shows that a two-parameter model can account for the fiber breaking and the expected distribution for ultimate stress is a Fréchet distribution. Copyright © 2015 Elsevier Ltd. All rights reserved.

49 CFR 195.12 - What requirements apply to low-stress pipelines in rural areas?

Code of Federal Regulations, 2014 CFR

2014-10-01

... corresponding to: (A) A stress level equal to or less than 20-percent of the specified minimum yield strength of the line pipe; or (B) If the stress level is unknown or the pipeline is not constructed with steel... of the specified minimum yield strength of the line pipe; or (B) If the stress level is unknown or...

49 CFR 195.12 - What requirements apply to low-stress pipelines in rural areas?

Code of Federal Regulations, 2013 CFR

2013-10-01

... corresponding to: (A) A stress level equal to or less than 20-percent of the specified minimum yield strength of the line pipe; or (B) If the stress level is unknown or the pipeline is not constructed with steel... of the specified minimum yield strength of the line pipe; or (B) If the stress level is unknown or...

49 CFR 195.12 - What requirements apply to low-stress pipelines in rural areas?

Code of Federal Regulations, 2012 CFR

2012-10-01

... corresponding to: (A) A stress level equal to or less than 20-percent of the specified minimum yield strength of the line pipe; or (B) If the stress level is unknown or the pipeline is not constructed with steel... of the specified minimum yield strength of the line pipe; or (B) If the stress level is unknown or...

Sea Ice

NASA Technical Reports Server (NTRS)

Perovich, D.; Gerland, S.; Hendricks, S.; Meier, Walter N.; Nicolaus, M.; Richter-Menge, J.; Tschudi, M.

2013-01-01

During 2013, Arctic sea ice extent remained well below normal, but the September 2013 minimum extent was substantially higher than the record-breaking minimum in 2012. Nonetheless, the minimum was still much lower than normal and the long-term trend Arctic September extent is -13.7 per decade relative to the 1981-2010 average. The less extreme conditions this year compared to 2012 were due to cooler temperatures and wind patterns that favored retention of ice through the summer. Sea ice thickness and volume remained near record-low levels, though indications are of slightly thicker ice compared to the record low of 2012.

MORPHOMETRIC ANALYSIS AND STRENGTH DETERMINATION OF OSTEOSCLEROTIC BONE RESULTING FROM HEXACHLOROBENZENE (HCB) EXPOSURE

EPA Science Inventory

Hexachlorobenzene (HCB) exposure has been shown to induce hyperparathyroidism and osteosclerosis in rats. xperiments were undertaken to investigate the effects of HCB on femur morphometry as well as breaking strength. ischer 344 rats were dosed 5 days/wk for 15 wks with 0, 0.1, 1...

46 CFR 160.176-4 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... and Elongation, Breaking of Woven Cloth; Grab Method—160.176-13 (2) Method 5132, Strength of Cloth, Tearing; Falling-Pendulum Method—160.176-13 (3) Method 5134, Strength of Cloth, Tearing; Tongue Method—160.176-13 (4) Method 5804.1, Weathering Resistance of Cloth; Accelerated Weathering Method—160.176-8 (5...

Improved Warm-Working Process For An Iron-Base Alloy

NASA Technical Reports Server (NTRS)

Cone, Fred P.; Cryns, Brendan J.; Miller, John A.; Zanoni, Robert

1992-01-01

Warm-working process produces predominantly unrecrystallized grain structure in forgings of iron-base alloy A286 (PWA 1052 composition). Yield strength and ultimate strength increased, and elongation and reduction of area at break decreased. Improved process used on forgings up to 10 in. thick and weighing up to 900 lb.

Planning to break unwanted habits: habit strength moderates implementation intention effects on behaviour change.

PubMed

Webb, Thomas L; Sheeran, Paschal; Luszczynska, Aleksandra

2009-09-01

Implementation intention formation promotes effective goal striving and goal attainment. However, little research has investigated whether implementation intentions promote behaviour change when people possess strong antagonistic habits. Experiment 1 developed relatively habitual responses that, after a task switch, had a detrimental impact on task performance. Forming an if-then plan reduced the negative impact of habit on performance. However, the effect of forming implementation intentions was smaller among participants who possessed strong habits as compared to participants who had weaker habits. Experiment 2 provided a field test of the role of habit strength in moderating the relationship between implementation intentions and behaviour in the context of smoking. Implementation intentions reduced smoking among participants with weak or moderate smoking habits, but not among participants with strong smoking habits. In summary, habit strength moderates the effectiveness of if-then plan formation in breaking unwanted habits.

Dope dyeing of lyocell fiber with NMMO-based carbon black dispersion.

PubMed

Zhang, Liping; Sun, Weize; Xu, Dan; Li, Min; Agbo, Christiana; Fu, Shaohai

2017-10-15

NMMO-based carbon black (CB) dispersion was prepared and its properties as well as its compatibility with lyocell spinning solution were further investigated. Modified lignosulfonate (SP) was verified to be the preeminent dispersant for the preparation of NMMO-based CB dispersion with mass ratio of SP to CB 20% and water to NMMO 13%. The compatibility of NMMO-based CB dispersion with lyocell spinning solution had close relation with dispersant structure and CB content. Mass ratio of CB to cellulose affects the mechanical properties, color strength and crystallinity of lyocell fiber. 0.5% CB increased the breaking strength and elongation of lyocell fiber, whiles breaking strength and elongation of the lyocell fiber were reduced slightly when 2.0% CB was used. The dope dyed fiber showed excellent rubbing and washing fastness as well as migration resistance to water, ethanol and acetone. Copyright © 2017 Elsevier Ltd. All rights reserved.

Explicitly broken supersymmetry with exactly massless moduli

NASA Astrophysics Data System (ADS)

Dong, Xi; Freedman, Daniel Z.; Zhao, Yue

2016-06-01

The AdS/CFT correspondence is applied to an analogue of the little hierarchy problem in three-dimensional supersymmetric theories. The bulk is governed by a super-gravity theory in which a U(1) × U(1) R-symmetry is gauged by Chern-Simons fields. The bulk theory is deformed by a boundary term quadratic in the gauge fields. It breaks SUSY completely and sources an exactly marginal operator in the dual CFT. SUSY breaking is communicated by gauge interactions to bulk scalar fields and their spinor superpartners. The bulk-to-boundary propagator of the Chern-Simons fields is a total derivative with respect to the bulk coordinates. Integration by parts and the Ward identity permit evaluation of SUSY breaking effects to all orders in the strength of the deformation. The R-charges of scalars and spinors differ so large SUSY breaking mass shifts are generated. Masses of R-neutral particles such as scalar moduli are not shifted to any order in the deformation strength, despite the fact that they may couple to R-charged fields running in loops. We also obtain a universal deformation formula for correlation functions under an exactly marginal deformation by a product of holomorphic and anti-holomorphic U(1) currents.

Axial strength test for round flat faced versus capsule shaped bilayer tablets.

PubMed

Franck, Jason; Abebe, Admassu; Keluskar, Rekha; Martin, Kyle; Majumdar, Antara; Kottala, Niranjan; Stamato, Howard

2015-03-01

There has been increasing interest in fixed dose combination (FDC) therapy. Multi-layer tablets are a popular choice among various technologies to deliver FDCs. In most cases, round flat faced tooling is used in testing tablets as they have the simplest geometry. However, shaped tooling is more common for commercial products and may have an effect on bilayer tablet strength. Capsule shaped bilayer tablets, similar to a commercial image, and holders conforming to the tablet topology, were compared with similar round flat faced bilayer tablets and their corresponding holders. Bilayer tablets were subjected to an axial test device, until fracture and the quantitative breaking force value was recorded. As the second layer compression force increases, regardless of holder design, an increase in breaking force occurs as expected. This consistent trend provides insight regarding the breaking force of capsule shaped bilayer tablets. The results of this study show that at lower second layer compression forces, tablet geometry does not significantly impact the results. However, at higher compression forces, a significant difference in breaking force between tablet geometries exists. Therefore, using a test geometry close to the final commercial tablet image is recommended to have the most accurate prediction for tablet breakage.

An MIP model to schedule the call center workforce and organize the breaks

NASA Astrophysics Data System (ADS)

Türker, Turgay; Demiriz, Ayhan

2016-06-01

In modern economies, companies place a premium on managing their workforce efficiently especially in labor intensive service sector, since the services have become the significant portion of the economies. Tour scheduling is an important tool to minimize the overall workforce costs while satisfying the minimum service level constraints. In this study, we consider the workforce management problem of an inbound call-center while satisfying the call demand within the short time periods with the minimum cost. We propose a mixed-integer programming model to assign workers to the daily shifts, to determine the weekly off-days, and to determine the timings of lunch and other daily breaks for each worker. The proposed model has been verified on the weekly demand data observed at a specific call center location of a satellite TV operator. The model was run on both 15 and 10 minutes demand estimation periods (planning time intervals).

Glass breaking strength: The role of surface flaws and treatments

NASA Technical Reports Server (NTRS)

Moore, D.

1985-01-01

Although the intrinsic strength of silicon dioxide glass is of the order of 10 to the 6th power lb/sq in, the practical strength is roughly two orders of magnitude below this theoretical limit, and depends almost entirely on the surface condition of the glass, that is, the number and size of flaws and the residual surface compression (temper) in the glass. Glass parts always fail in tension when these flaws grow under sustained loading to some critical size. Research associated with glass encapsulated crystalline-Si photovoltaic (PV) modules has greatly expanded our knowledge of glass breaking strength and developed sizeable data base for commercially available glass types. A detailed design algorithm is developed for thickness sizing of rectangular glass plates subject to pressure loads. Additional studies examine the strength of glass under impact loading conditions such as that caused by hail. Although the fundamentals of glass breakage are directly applicable to thin film modules, the fracture strength of typical numerical glass must be replaced with data that reflect the high temperature tin oxide processing, laser scribing, and edge processing peculiar to thin film modules. The fundamentals of glass breakage applicable to thin film modules and preliminary fracture strength data for a variety of 1 ft square glass specimens representing preprocessed and post processed sheets from current amorphous-Si module manufacturers are presented.

Mechanical sea-ice strength parameterized as a function of ice temperature

NASA Astrophysics Data System (ADS)

Hata, Yukie; Tremblay, Bruno

2016-04-01

Mechanical sea-ice strength is key for a better simulation of the timing of landlock ice onset and break-up in the Canadian Arctic Archipelago (CAA). We estimate the mechanical strength of sea ice in the CAA by analyzing the position record measured by the several buoys deployed in the CAA between 2008 and 2013, and wind data from the Canadian Meteorological Centre's Global Deterministic Prediction System (CMC_GDPS) REforecasts (CGRF). First, we calculate the total force acting on the ice using the wind data. Next, we estimate upper (lower) bounds on the sea-ice strength by identifying cases when the sea ice deforms (does not deform) under the action of a given total force. Results from this analysis show that the ice strength of landlock sea ice in the CAA is approximately 40 kN/m on the landfast ice onset (in ice growth season). Additionally, it becomes approximately 10 kN/m on the landfast ice break-up (in melting season). The ice strength decreases with ice temperature increase, which is in accord with results from Johnston [2006]. We also include this new parametrization of sea-ice strength as a function of ice temperature in a coupled slab ocean sea ice model. The results from the model with and without the new parametrization are compared with the buoy data from the International Arctic Buoy Program (IABP).

Development of Low-Carbon, Copper-Strengthened HSLA Steel Plate for Naval Ship Construction

DTIC Science & Technology

1990-06-01

steel plate microstructures, 2% nital etch . ...................................................... 13 2. Charpy V-notch impact energy transition for...met a minimum yield strength requirement of 80 ksi yield strength through 3/4 inch gage, had high Charpy V-notch impact energy at low tempera- tures...tempered HSLA line-pipe steels, which typically could not meet the minimum Charpy V-notch impact toughness requirement of 35 ft-lb at -1 200 F. In 1984

Stress corrosion evaluation of powder metallurgy aluminum alloy 7091 with the breaking load test method

NASA Technical Reports Server (NTRS)

Domack, Marcia S.

1987-01-01

The stress corrosion behavior of the P/M aluminum alloy 7091 is evaluated in two overaged heat treatment conditions, T7E69 and T7E70, using an accelerated test technique known as the breaking load test method. The breaking load data obtained in this study indicate that P/M 7091 alloy is highly resistant to stress corrosion in both longitudinal and transverse orientations at stress levels up to 90 percent of the material yield strength. The reduction in mean breaking stress as a result of corrosive attack is smallest for the more overaged T7E70 condition. Details of the test procedure are included.

The raising of minimum alcohol prices in Saskatchewan, Canada: impacts on consumption and implications for public health.

PubMed

Stockwell, Tim; Zhao, Jinhui; Giesbrecht, Norman; Macdonald, Scott; Thomas, Gerald; Wettlaufer, Ashley

2012-12-01

We report impacts on alcohol consumption following new and increased minimum alcohol prices in Saskatchewan, Canada. We conducted autoregressive integrated moving average time series analyses of alcohol sales and price data from the Saskatchewan government alcohol monopoly for 26 periods before and 26 periods after the intervention. A 10% increase in minimum prices significantly reduced consumption of beer by 10.06%, spirits by 5.87%, wine by 4.58%, and all beverages combined by 8.43%. Consumption of coolers decreased significantly by 13.2%, cocktails by 21.3%, and liqueurs by 5.3%. There were larger effects for purely off-premise sales (e.g., liquor stores) than for primarily on-premise sales (e.g., bars, restaurants). Consumption of higher strength beer and wine declined the most. A 10% increase in minimum price was associated with a 22.0% decrease in consumption of higher strength beer (> 6.5% alcohol/volume) versus 8.17% for lower strength beers. The neighboring province of Alberta showed no change in per capita alcohol consumption before and after the intervention. Minimum pricing is a promising strategy for reducing the public health burden associated with hazardous alcohol consumption. Pricing to reflect percentage alcohol content of drinks can shift consumption toward lower alcohol content beverage types.

Symmetry breaking and singularity structure in Bose-Einstein condensates

NASA Astrophysics Data System (ADS)

Commeford, K. A.; Garcia-March, M. A.; Ferrando, A.; Carr, Lincoln D.

2012-08-01

We determine the trajectories of vortex singularities that arise after a single vortex is broken by a discretely symmetric impulse in the context of Bose-Einstein condensates in a harmonic trap. The dynamics of these singularities are analyzed to determine the form of the imprinted motion. We find that the symmetry-breaking process introduces two effective forces: a repulsive harmonic force that causes the daughter trajectories to be ejected from the parent singularity and a Magnus force that introduces a torque about the axis of symmetry. For the analytical noninteracting case we find that the parent singularity is reconstructed from the daughter singularities after one period of the trapping frequency. The interactions between singularities in the weakly interacting system do not allow the parent vortex to be reconstructed. Analytic trajectories were compared to the actual minima of the wave function, showing less than 0.5% error for an impulse strength of v=0.00005. We show that these solutions are valid within the impulse regime for various impulse strengths using numerical integration of the Gross-Pitaevskii equation. We also show that the actual duration of the symmetry-breaking potential does not significantly change the dynamics of the system as long as the strength is below v=0.0005.

Fabrication and properties of polyvinyl alcohol/starch blend films: Effect of composition and humidity.

PubMed

Tian, Huafeng; Yan, Jiaan; Rajulu, A Varada; Xiang, Aimin; Luo, Xiaogang

2017-03-01

In this work, starch/polyvinyl alcohol (PVA) blend films with different compositions were prepared by melt processing. The effect of the composition and relative humidity (RH) on the structure and properties of the resulting blends were investigated. OH groups on starch and PVA formed hydrogen bonding interactions, which could improve the compatibility of the two components. With the increase of starch, the degree of crystallinity of PVA component decreased. The fracture surface of the blend films exhibited rough surface, suggesting the tough fracture. With the increase of starch, the water uptake at equilibrium decreased. With the increase of RH, the water uptake at equilibrium of the resulting blends increased. The tensile strength, elongation at break and Young's modulus decreased with increasing content of starch. However, at 50% starch content, the flexibility of the blend films was still high, with the elongation at break more than 1000% and tensile strength of 9MPa, which was superior to the commonly LDPE package films. The tensile strength and Young's modulus decreased with the increase of RH, while the elongation at break was enhanced dramatically, indicating the improved flexibility. Therefore, these kinds of blend films exhibited wide application potentials as packaging materials. Copyright © 2016 Elsevier B.V. All rights reserved.

Wound Healing Activity of Topical Application Forms Based on Ayurveda

PubMed Central

Datta, Hema Sharma; Mitra, Shankar Kumar; Patwardhan, Bhushan

2011-01-01

The traditional Indian medicine—Ayurveda, describes various herbs, fats, oils and minerals with anti-aging as well as wound healing properties. With aging, numerous changes occur in skin, including decrease in tissue cell regeneration, decrease in collagen content, loss of skin elasticity and mechanical strength. We prepared five topical anti-aging formulations using cow ghee, flax seed oil, Phyllanthus emblica fruits, Shorea robusta resin, Yashada bhasma as study materials. For preliminary efficacy evaluation of the anti-aging activity we chose excision and incision wound healing animal models and studied the parameters including wound contraction, collagen content and skin breaking strength which in turn is indicative of the tissue cell regeneration capacity, collagenation capacity and mechanical strength of skin. The group treated with the formulations containing Yashada bhasma along with Shorea robusta resin and flax seed oil showed significantly better wound contraction (P < .01), higher collagen content (P < .05) and better skin breaking strength (P < .01) as compared to control group; thus proposing them to be effective prospective anti-aging formulations. PMID:19252191

Probabilistic simulation of uncertainties in composite uniaxial strengths

NASA Technical Reports Server (NTRS)

Chamis, C. C.; Stock, T. A.

1990-01-01

Probabilistic composite micromechanics methods are developed that simulate uncertainties in unidirectional fiber composite strengths. These methods are in the form of computational procedures using composite mechanics with Monte Carlo simulation. The variables for which uncertainties are accounted include constituent strengths and their respective scatter. A graphite/epoxy unidirectional composite (ply) is studied to illustrate the procedure and its effectiveness to formally estimate the probable scatter in the composite uniaxial strengths. The results show that ply longitudinal tensile and compressive, transverse compressive and intralaminar shear strengths are not sensitive to single fiber anomalies (breaks, intergacial disbonds, matrix microcracks); however, the ply transverse tensile strength is.

Alloys For Corrosive, Hydrogen-Rich Environments

NASA Technical Reports Server (NTRS)

Mcpherson, William B.; Bhat, Biliyar N.; Chen, Po-Shou; Kuruvilla, A. K.; Panda, Binayak

1993-01-01

"NASA-23" denotes class of alloys resisting both embrittlement by hydrogen and corrosion. Weldable and castable and formed by such standard processes as rolling, forging, and wire drawing. Heat-treated to obtain desired combinations of strength and ductility in ranges of 100 to 180 kpsi yield strength, 120 to 200 kpsi ultimate tensile strength, and 10 to 30 percent elongation at break. Used in place of most common aerospace structural alloy, Inconel(R) 718.

Toughening elastomers with sacrificial bonds and watching them break.

PubMed

Ducrot, Etienne; Chen, Yulan; Bulters, Markus; Sijbesma, Rint P; Creton, Costantino

2014-04-11

Elastomers are widely used because of their large-strain reversible deformability. Most unfilled elastomers suffer from a poor mechanical strength, which limits their use. Using sacrificial bonds, we show how brittle, unfilled elastomers can be strongly reinforced in stiffness and toughness (up to 4 megapascals and 9 kilojoules per square meter) by introducing a variable proportion of isotropically prestretched chains that can break and dissipate energy before the material fails. Chemoluminescent cross-linking molecules, which emit light as they break, map in real time where and when many of these internal bonds break ahead of a propagating crack. The simple methodology that we use to introduce sacrificial bonds, combined with the mapping of where bonds break, has the potential to stimulate the development of new classes of unfilled tough elastomers and better molecular models of the fracture of soft materials.

49 CFR 179.220-6 - Thickness of plates.

Code of Federal Regulations, 2010 CFR

2010-10-01

... heads; P = Minimum required bursting pressure in psig; S = Minimum tensile strength of plate material in p.s.i. as prescribed in AAR Specifications for Tank Cars, appendix M, Table M1; t = Minimum... seamless heads; L = Main inside radius to which head is dished, measured on concave side in inches; P...

Effects of trampling on morphological and mechanical traits of dryland shrub species do not depend on water availability.

PubMed

Xu, Liang; Freitas, Sofia M A; Yu, Fei-Hai; Dong, Ming; Anten, Niels P R; Werger, Marinus J A

2013-01-01

In semiarid drylands water shortage and trampling by large herbivores are two factors limiting plant growth and distribution. Trampling can strongly affect plant performance, but little is known about responses of morphological and mechanical traits of woody plants to trampling and their possible interaction with water availability. Seedlings of four shrubs (Caragana intermedia, Cynanchum komarovi, Hedysarum laeve and Hippophae rhamnoides) common in the semiarid Mu Us Sandland were grown at 4% and 10% soil water content and exposed to either simulated trampling or not. Growth, morphological and mechanical traits were measured. Trampling decreased vertical height and increased basal diameter and stem resistance to bending and rupture (as indicated by the increased minimum bend and break force) in all species. Increasing water availability increased biomass, stem length, basal diameter, leaf thickness and rigidity of stems in all species except C. komarovii. However, there were no interactive effects of trampling and water content on any of these traits among species except for minimum bend force and the ratio between stem resistance to rupture and bending. Overall shrub species have a high degree of trampling resistance by morphological and mechanical modifications, and the effects of trampling do not depend on water availability. However, the increasing water availability can also affect trade-off between stem strength and flexibility caused by trampling, which differs among species. Water plays an important role not only in growth but also in trampling adaptation in drylands.

From brittle to ductile fracture in disordered materials.

PubMed

Picallo, Clara B; López, Juan M; Zapperi, Stefano; Alava, Mikko J

2010-10-08

We introduce a lattice model able to describe damage and yielding in heterogeneous materials ranging from brittle to ductile ones. Ductile fracture surfaces, obtained when the system breaks once the strain is completely localized, are shown to correspond to minimum energy surfaces. The similarity of the resulting fracture paths to the limits of brittle fracture or minimum energy surfaces is quantified. The model exhibits a smooth transition from brittleness to ductility. The dynamics of yielding exhibits avalanches with a power-law distribution.

Material Properties and Antimicrobial Activity of Polyhydroxybutyrate (PHB) Films Incorporated with Vanillin.

PubMed

Xavier, Janifer Raj; Babusha, Sudalaimuthu Thangaraj; George, Johnsy; Ramana, Karna Venkata

2015-07-01

Polyhydroxybutyrate (PHB) was produced by Bacillus mycoides DFC 1, isolated from garden soil. Antimicrobial (AM) films of PHB were prepared by incorporating vanillin (4-hydroxy-3-methoxybenzaldehyde) from 10 to 200 μg/g of PHB. The films were assessed for antimicrobial activity against foodborne pathogens and spoilage bacteria comprising of Escherichia coli, Salmonella typhimurium, Shigella flexneri, and Staphylococcus aureus and fungi such as Aspergillus flavus, Aspergillus fumigatus, Aspergillus niger, Aspergillus parasiticus, Aspergillus ochraceus, Penicillium viridicatum, and Penicillium clavigerum. The minimum concentration of vanillin required to exhibit antimicrobial activity was ≥80 μg/g PHB for bacteria and ≥50 μg/g PHB for fungi. The PHB films with and without vanillin were studied for mechanical and thermal properties such as tensile strength, Young's modulus, percentage elongation to break, melting temperature, and heat of fusion. The thermal stability of the films was studied using thermogravimetric analysis. The release kinetics of vanillin into food matrices was also checked using food stimulants. The study is intended to find applications for PHB films containing vanillin to enhance the shelf life of foods in the form of biodegradable wrapper.

Design of the NUSC (Naval Underwater System Center) Replacement TCP (transducer Calibration Platform) Mooring for Lake Seneca, Dresden, New York

DTIC Science & Technology

1983-05-01

SMP has sinkers attached to wire rope within the water column. This location of sinkers was not duplicated on the TCP moor because of possible wear and...breaking (new chain) 1-3/4" wire rope breaking strength is approx. 224. kips; F.S. = 6.4 against breaking (new rope) Buoy, dia=9.5’,h=5’ buoy freeboard is...6.4 against breakingconnecting agis 1-3/4" wire rope with J b- chain tails 13 See Appendix B for details of the mooring buoy design and Appendix C

Cooperation and competition between two symmetry breakings in a coupled ratchet

NASA Astrophysics Data System (ADS)

Li, Chen-Pu; Chen, Hong-Bin; Fan, Hong; Xie, Ge-Ying; Zheng, Zhi-Gang

2018-03-01

We investigate the collective mechanism of coupled Brownian motors in a flashing ratchet in the presence of coupling symmetry breaking and space symmetry breaking. The dependences of directed current on various parameters are extensively studied in terms of numerical simulations and theoretical analysis. Reversed motion can be achieved by modulating multiple parameters including the spatial asymmetry coefficient, the coupling asymmetry coefficient, the coupling free length and the coupling strength. The dynamical mechanism of these transport properties can be reasonably explained by the effective potential theory and the cooperation or competition between two symmetry breakings. Moreover, adjusting the Gaussian white noise intensity, which can induce weak reversed motion under certain condition, can optimize and manipulate the directed transport of the ratchet system.

Impact of symmetry breaking in networks of globally coupled oscillators

NASA Astrophysics Data System (ADS)

Premalatha, K.; Chandrasekar, V. K.; Senthilvelan, M.; Lakshmanan, M.

2015-05-01

We analyze the consequences of symmetry breaking in the coupling in a network of globally coupled identical Stuart-Landau oscillators. We observe that symmetry breaking leads to increased disorderliness in the dynamical behavior of oscillatory states and consequently results in a rich variety of dynamical states. Depending on the strength of the nonisochronicity parameter, we find various dynamical states such as amplitude chimera, amplitude cluster, frequency chimera, and frequency cluster states. In addition we also find disparate transition routes to recently observed chimera death states in the presence of symmetry breaking even with global coupling. We also analytically verify the chimera death region, which corroborates the numerical results. These results are compared with that of the symmetry-preserving case as well.

Wilson-loop instantons

NASA Technical Reports Server (NTRS)

Lee, Kimyeong; Holman, Richard; Kolb, Edward W.

1987-01-01

Wilson-loop symmetry breaking is considered on a space-time of the form M4 x K, where M4 is a four-dimensional space-time and K is an internal space with nontrivial and finite fundamental group. It is shown in a simple model that the different vacua obtained by breaking a non-Abelian gauge group by Wilson loops are separated in the space of gauge potentials by a finite energy barrier. An interpolating gauge configuration is then constructed between these vacua and shown to have minimum energy. Finally some implications of this construction are discussed.

16 CFR 1500.86 - Exemptions from classification as a banned toy or other banned article for use by children.

Code of Federal Regulations, 2014 CFR

2014-01-01

... materials other than those materials (such as ABS (acrylonitrile butadiene styrene), nylon, and high-impact polystyrene) that are injection-molded and possess high-impact characteristics. (B) The cord: Is of high tensile strength, synthetic fibers that are braided or woven, having a breaking strength in excess of 445...

16 CFR 1500.86 - Exemptions from classification as a banned toy or other banned article for use by children.

Code of Federal Regulations, 2012 CFR

2012-01-01

... materials other than those materials (such as ABS (acrylonitrile butadiene styrene), nylon, and high-impact polystyrene) that are injection-molded and possess high-impact characteristics. (B) The cord: Is of high tensile strength, synthetic fibers that are braided or woven, having a breaking strength in excess of 445...

16 CFR 1500.86 - Exemptions from classification as a banned toy or other banned article for use by children.

Code of Federal Regulations, 2011 CFR

2011-01-01

... materials other than those materials (such as ABS (acrylonitrile butadiene styrene), nylon, and high-impact polystyrene) that are injection-molded and possess high-impact characteristics. (B) The cord: Is of high tensile strength, synthetic fibers that are braided or woven, having a breaking strength in excess of 445...

A laser-induced pulsed water jet for layer-selective submucosal dissection of the esophagus

PubMed Central

Sato, C; Yamada, M; Nakagawa, A; Yamamoto, H; Fujishima, F; Tominaga, T; Satomi, S; Ohuchi, N

2016-01-01

Background and aims: Conventional water jet devices have been used for injecting fluid to lift up lesions during endoscopic submucosal dissection or endoscopic mucosal resection procedures. However, these devices cannot dissect the submucosal layer effectively. Here we aim to elucidate the dissection capability of a laser-induced pulsed water jet and to clarify the mechanism of dissection with layer selectivity. Materials (Subjects) and methods: Pulsed water jets were ejected from a stainless nozzle by accelerating saline using the energy of a pulsed holmium: yttrium-aluminum-garnet laser. The impact force (strength) of the jet was evaluated using a force meter. Injection of the pulsed jet into the submucosal layer was documented by high-speed imaging. The physical properties of the swine esophagus were evaluated by measuring the breaking strength. Submucosal dissection of the swine esophagus was performed and the resection bed was evaluated histologically. Results: Submucosal dissection of the esophagus was accomplished at an impact force of 1.11–1.47 N/pulse (laser energy: 1.1–1.5 J/pulse; standoff distance: 60 mm). Histological specimens showed clear dissection at the submucosal layer without thermal injury. The mean static breaking strength of the submucosa (0.11 ± 0.04 MPa) was significantly lower than that of the mucosa (1.32 ± 0.18 MPa), and propria muscle (1.45 ± 0.16 MPa). Conclusions: The pulsed water jet device showed potential for achieving selective submucosal dissection. It could achieve mucosal, submucosal, and muscle layer selectivity owing to the varied breaking strengths. PMID:27853343

The Raising of Minimum Alcohol Prices in Saskatchewan, Canada: Impacts on Consumption and Implications for Public Health

PubMed Central

Zhao, Jinhui; Giesbrecht, Norman; Macdonald, Scott; Thomas, Gerald; Wettlaufer, Ashley

2012-01-01

Objectives. We report impacts on alcohol consumption following new and increased minimum alcohol prices in Saskatchewan, Canada. Methods. We conducted autoregressive integrated moving average time series analyses of alcohol sales and price data from the Saskatchewan government alcohol monopoly for 26 periods before and 26 periods after the intervention. Results. A 10% increase in minimum prices significantly reduced consumption of beer by 10.06%, spirits by 5.87%, wine by 4.58%, and all beverages combined by 8.43%. Consumption of coolers decreased significantly by 13.2%, cocktails by 21.3%, and liqueurs by 5.3%. There were larger effects for purely off-premise sales (e.g., liquor stores) than for primarily on-premise sales (e.g., bars, restaurants). Consumption of higher strength beer and wine declined the most. A 10% increase in minimum price was associated with a 22.0% decrease in consumption of higher strength beer (> 6.5% alcohol/volume) versus 8.17% for lower strength beers. The neighboring province of Alberta showed no change in per capita alcohol consumption before and after the intervention. Conclusions. Minimum pricing is a promising strategy for reducing the public health burden associated with hazardous alcohol consumption. Pricing to reflect percentage alcohol content of drinks can shift consumption toward lower alcohol content beverage types. PMID:23078488

30 CFR 56.19021 - Minimum rope strength.

Code of Federal Regulations, 2010 CFR

2010-07-01

...=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0-0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0 (c) Tail ropes....19021 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 57.19021 - Minimum rope strength.

Code of Federal Regulations, 2011 CFR

2011-07-01

...=Static Load×4.0. (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0. (c) Tail....19021 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 57.19021 - Minimum rope strength.

Code of Federal Regulations, 2010 CFR

2010-07-01

...=Static Load×4.0. (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0. (c) Tail....19021 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 56.19021 - Minimum rope strength.

Code of Federal Regulations, 2011 CFR

2011-07-01

...=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0-0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0 (c) Tail ropes....19021 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 75.1431 - Minimum rope strength.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) For rope lengths 3,000 feet or greater: Minimum Value=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH...

30 CFR 75.1431 - Minimum rope strength.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) For rope lengths 3,000 feet or greater: Minimum Value=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH...

49 CFR 192.505 - Strength test requirements for steel pipeline to operate at a hoop stress of 30 percent or more...

Code of Federal Regulations, 2013 CFR

2013-10-01

... sections of pipe, for which a post installation test is impractical, a preinstallation strength test must... 49 Transportation 3 2013-10-01 2013-10-01 false Strength test requirements for steel pipeline to...: MINIMUM FEDERAL SAFETY STANDARDS Test Requirements § 192.505 Strength test requirements for steel pipeline...

Point sensitive NMR imaging system using a magnetic field configuration with a spatial minimum

DOEpatents

Eberhard, P.H.

A point-sensitive NMR imaging system in which a main solenoid coil produces a relatively strong and substantially uniform magnetic field and a pair of perturbing coils powered by current in the same direction superimposes a pair of relatively weak perturbing fields on the main field to produce a resultant point of minimum field strength at a desired location in a direction along the Z-axis. Two other pairs of perturbing coils superimpose relatively weak field gradients on the main field in directions along the X- and Y-axes to locate the minimum field point at a desired location in a plane normal to the Z-axes. An rf generator irradiates a tissue specimen in the field with radio frequency energy so that desired nuclei in a small volume at the point of minimum field strength will resonate.

A Rational Approach to Determine Minimum Strength Thresholds in Novel Structural Materials

NASA Technical Reports Server (NTRS)

Schur, Willi W.; Bilen, Canan; Sterling, Jerry

2003-01-01

Design of safe and survivable structures requires the availability of guaranteed minimum strength thresholds for structural materials to enable a meaningful comparison of strength requirement and available strength. This paper develops a procedure for determining such a threshold with a desired degree of confidence, for structural materials with none or minimal industrial experience. The problem arose in attempting to use a new, highly weight-efficient structural load tendon material to achieve a lightweight super-pressure balloon. The developed procedure applies to lineal (one dimensional) structural elements. One important aspect of the formulation is that it extrapolates to expected probability distributions for long length specimen samples from some hypothesized probability distribution that has been obtained from a shorter length specimen sample. The use of the developed procedure is illustrated using both real and simulated data.

Breaking through the strength-ductility trade-off dilemma in an Al-Si-based casting alloy.

PubMed

Dang, B; Zhang, X; Chen, Y Z; Chen, C X; Wang, H T; Liu, F

2016-08-09

Al-Si-based casting alloys have a great potential in various industrial applications. Common strengthening strategies on these alloys are accompanied inevitably by sacrifice of ductility, known as strength-ductility trade-off dilemma. Here, we report a simple route by combining rapid solidification (RS) with a post-solidification heat treatment (PHT), i.e. a RS + PHT route, to break through this dilemma using a commercial Al-Si-based casting alloy (A356 alloy) as an example. It is shown that yield strength and elongation to failure of the RS + PHT processed alloy are elevated simultaneously by increasing the cooling rate upon RS, which are not influenced by subsequent T6 heat treatment. Breaking through the dilemma is attributed to the hierarchical microstructure formed by the RS + PHT route, i.e. highly dispersed nanoscale Si particles in Al dendrites and nanoscale Al particles decorated in eutectic Si. Simplicity of the RS + PHT route makes it being suitable for industrial scaling production. The strategy of engineering microstructures offers a general pathway in tailoring mechanical properties of other Al-Si-based alloys. Moreover, the remarkably enhanced ductility of A356 alloy not only permits strengthening further the material by work hardening but also enables possibly conventional solid-state forming of the material, thus extending the applications of such an alloy.

Breaking through the strength-ductility trade-off dilemma in an Al-Si-based casting alloy

PubMed Central

Dang, B.; Zhang, X.; Chen, Y. Z.; Chen, C. X.; Wang, H. T.; Liu, F.

2016-01-01

Al-Si-based casting alloys have a great potential in various industrial applications. Common strengthening strategies on these alloys are accompanied inevitably by sacrifice of ductility, known as strength-ductility trade-off dilemma. Here, we report a simple route by combining rapid solidification (RS) with a post-solidification heat treatment (PHT), i.e. a RS + PHT route, to break through this dilemma using a commercial Al-Si-based casting alloy (A356 alloy) as an example. It is shown that yield strength and elongation to failure of the RS + PHT processed alloy are elevated simultaneously by increasing the cooling rate upon RS, which are not influenced by subsequent T6 heat treatment. Breaking through the dilemma is attributed to the hierarchical microstructure formed by the RS + PHT route, i.e. highly dispersed nanoscale Si particles in Al dendrites and nanoscale Al particles decorated in eutectic Si. Simplicity of the RS + PHT route makes it being suitable for industrial scaling production. The strategy of engineering microstructures offers a general pathway in tailoring mechanical properties of other Al-Si-based alloys. Moreover, the remarkably enhanced ductility of A356 alloy not only permits strengthening further the material by work hardening but also enables possibly conventional solid-state forming of the material, thus extending the applications of such an alloy. PMID:27502444

Plasticization of Poly (lactic) acid Film as a Potential Coating Material

NASA Astrophysics Data System (ADS)

Yang, Ping; Li, Hua; Liu, Qingsong; Dong, Hongbiao; Duan, Yafei; Zhang, Jiasong

2018-01-01

PLA-based composite films with different plasticizers, such as polyethylene glycol (PEG) and Tributyl citrate (TBC), were prepared using a solvent casting method and their machanical, water absorbency and NO3 --N permeability properties were tested. Tensile strength, elongation at break, water absorbency and NO3 --N permeability of neat PLA film were 1.99 ± 0.04 MPa, 2.7 ± 0.46%, 29.33 ± 0.3% and 216.03 ± 19.92 mg·L-1·m-2·h-1, respectively. After the addition of plasticizers the tensile strength were decreased, tensile strength of flims added 40wt% TBC and PEG decreased by 59.3% and 52.26%. While the elongation at break of the PLA film gradually increased. The elongation at break reached the value of 23.96±0.48% and 38.55±1.66% for the films added PEG and TBC respectively at the concentration of 40wt%. Water absorbency decreased as the increase of plasticizers. The NO3 --N permeability attained a maximum of 300.05±10.47 and 270.97±14.54 mg·L-1·m-2·h-1 for films added PEG and TBC at the concentration of 10 wt % respectively. Considered the NO3 --N permeability, PEG at 10wt% seemed the better plasticizer for PLA used in control release of fertilizer.

The effect of increasing chitosan on the characteristics of bioplastic from starch talas (Colocasia esculenta) using plasticizer sorbitol

NASA Astrophysics Data System (ADS)

Ginting, M. H. S.; Lubis, M.; Sidabutar, T.; Sirait, T. P.

2018-03-01

The aims of this research to determine the profile of starch gelatinization, bioplastic and the effect of increasing chitosan and sorbitol to the properties of tensile strength and elongation of break bioplastic. Preparation of bioplastics was used by casting method, that is 30% w/v solution of starch mixed with chitosan solution (0.5 w/v; 1 w/v; 1.5 w/v; 2 w/v; and 2.5 w/v) and plasticizer sorbitol (10 % w/w; 20 % w/w; 30 % w/w; 40 % w/w and 50 % w/w) were heated using a hotplate magnetic stirrer at 750C. The results of Rapid Visco Analyzer (RVA) obtained by starch and bioplastic gelatinization temperature of 72.94°C 77.72°C with peak viscosity 6632 cP and 3476 cP. Analysis of Fourier Transform Infrared (FTIR) and Scanning Electron Microscopy (SEM) obtained the change a functional group of bioplastic OH at wave number 3765 cm-1 and uneven chitosan distribution, and there is still an empty fraction. The addition of chitosan and sorbitol had an effect on tensile strength and elongation at break, tensile strength and elongation at break the highest of 8.36 MPa and 22.06% in starch composition 30%, 2.5 w/v chitosan and sorbitol 30% w/w.

16 CFR § 1500.86 - Exemptions from classification as a banned toy or other banned article for use by children.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (acrylonitrile butadiene styrene), nylon, and high-impact polystyrene) that are injection-molded and possess high-impact characteristics. (B) The cord: Is of high tensile strength, synthetic fibers that are braided or woven, having a breaking strength in excess of 445 Newtons (100 pounds); is free of fraying or any other...

Biotic - Abiotic Interface Between they Body and the Artificial Limb

DTIC Science & Technology

2008-09-29

transcutaneous amputation prosthesis ; machining; osseointegration; polycaprolactone; surface roughness; tensile strength; tissue adhesion; tissue...centrifuge at 2000 rpm for 5 minutes to remove air bubbles. This solution was then used for scaffold printing. Printing PCL Scaffolds The syringe was...Instron Corp., Norwood, Massachusetts) was used to test breaking strength. Briefly, the skin and underlying disc was removed en-block measuring

Signatures of moderate (M-class) and low (C and B class) intensity solar flares on the equatorial electrojet current: Case studies

NASA Astrophysics Data System (ADS)

Chakrabarty, D.; Bagiya, Mala S.; Thampi, Smitha V.; Pathan, B. M.; Sekar, R.

2013-12-01

The present investigation brings out, in contrast to the earlier works, the changes in the equatorial electrojet (EEJ) current in response to a few moderate (M-class) and low (C and B class) intensity solar flares during 2005-2010. Special care is taken to pick these flare events in the absence of prompt electric field perturbations associated with geomagnetic storms and substorms that also affect the electrojet current. Interestingly, only the normalized (with respect to the pre-flare level) deviations of daytime EEJ (and not the deviations alone) change linearly with the increases in the EUV and X-ray fluxes. These linear relationships break down during local morning hours when the E-region electric field approaches zero before reversal of polarity. This elicits that the response of EEJ strength corresponding to less-intense flares can be appropriately gauged only when the local time variation of the quiet time E-region zonal electric field is taken into account. The flare events enhanced the EEJ strength irrespective of normal or counter electrojet (CEJ) conditions that shows that solar flares change the E-region ionization density and not the electric field. In addition, the enhancements in the X-ray and EUV fluxes, for these flares occurring during this solar minimum period, are found to be significantly correlated as opposed to the solar maximum period, indicating the differences in the solar processes in different solar epochs.

Combined effect of pH and heating conditions on the physical properties of Alaska pollock surimi gels.

PubMed

Lee, Myeong Gi; Yoon, Won Byong; Park, Jae W

2017-06-01

Physical properties of Alaska pollock surimi paste were investigated as affected by pH (4.0 and 6.0-10.0) and heating conditions (slow and fast). The highest values of gel strength and deformability, as shown by breaking force and penetration distance, were obtained at pH 7.5-8.0, while the lowest values were at pH 10.0 followed by pH 6.0 and pH 6.5, respectively. Two-step slow heating process increased the breaking strength value nearly two times higher than one-step fast heating. The effect of pH was strikingly high at pH 7.5 when gels were prepared using 2-step heating, indicating the pH dependence of endogenous transglutaminase. However, the highest gel strength was obtained at pH 8.0 when gels were prepared in fast heating. Whiteness value (L - 3b*) increased significantly (p < .05) as pH increased from 6.0 to 6.5, but thereafter decreased significantly (p < .05) as pH increased. L* value (lightness) and b* value (yellowness) continuously decreased as the pH is shifted from 6.0 to 10. Fast heated gels showed the lowest yellowness, resulting in whiter appearance, probably due to the effect of reduced browning reaction. The uniqueness of this study was to measure the combined effect of pH and heating conditions on the gel texture and color. There were various studies dealing with pH or heating conditions independently. As the primary character for surimi seafood is gel texture and color. The highest values of gel strength and deformability, as shown by breaking force and penetration distance, were obtained at pH 7.5-8.0, while the lowest values were at pH 10.0 followed by pH 6.0 and pH 6.5, respectively. Two-step slow heating process increased the breaking strength value nearly two times higher than one-step fast heating. Whiteness value (L - 3b*) increased significantly as pH increased from 6.0 to 6.5, but thereafter decreased significantly as pH increased. L* value (lightness) and b* value (yellowness) continuously decreased as the pH is shifted from 6.0 to 10. Fast heated gels showed the lowest yellowness, resulting in whiter appearance. © 2016 Wiley Periodicals, Inc.

PT-symmetry breaking with divergent potentials: Lattice and continuum cases

NASA Astrophysics Data System (ADS)

Joglekar, Yogesh N.; Scott, Derek D.; Saxena, Avadh

2014-09-01

We investigate the parity- and time-reversal (PT-) symmetry breaking in lattice models in the presence of long-ranged, non-Hermitian, PT-symmetric potentials that remain finite or become divergent in the continuum limit. By scaling analysis of the fragile PT threshold for an open finite lattice, we show that continuum loss-gain potentials Vα(x)∝i|x|αsgn(x) have a positive PT-breaking threshold for α >-2, and a zero threshold for α ≤-2. When α <0 localized states with complex (conjugate) energies in the continuum energy band occur at higher loss-gain strengths. We investigate the signatures of PT-symmetry breaking in coupled waveguides, and show that the emergence of localized states dramatically shortens the relevant time scale in the PT-symmetry broken region.

30 CFR 77.1431 - Minimum rope strength.

Code of Federal Regulations, 2011 CFR

2011-07-01

...=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0 (c) Tail ropes... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH...

30 CFR 77.1431 - Minimum rope strength.

Code of Federal Regulations, 2010 CFR

2010-07-01

...=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0 (c) Tail ropes... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH...

A physical mechanism for the prediction of the sunspot number during solar cycle 21. [graphs (charts)

NASA Technical Reports Server (NTRS)

Schatten, K. H.; Scherrer, P. H.; Svalgaard, L.; Wilcox, J. M.

1978-01-01

On physical grounds it is suggested that the sun's polar field strength near a solar minimum is closely related to the following cycle's solar activity. Four methods of estimating the sun's polar magnetic field strength near solar minimum are employed to provide an estimate of cycle 21's yearly mean sunspot number at solar maximum of 140 plus or minus 20. This estimate is considered to be a first order attempt to predict the cycle's activity using one parameter of physical importance.

Investigation of concrete containing condensed silica fume.

DOT National Transportation Integrated Search

1986-01-01

The properties of hydraulic cement concretes containing silica fume were investigated to assess their suitability for use in overlays with s minimum thickness of 1 1/4 in. The properties studied were compressive and flexural strengths, bond strength,...

Calculation of temperature distribution and rheological properties of the lithosphere along geotransect in the Red Sea region

NASA Astrophysics Data System (ADS)

Dérerová, Jana; Kohút, Igor; Radwan, Anwar H.; Bielik, Miroslav

2017-12-01

The temperature model of the lithosphere along profile passing through the Red Sea region has been derived using 2D integrated geophysical modelling method. Using the extrapolation of failure criteria, lithology and calculated temperature distribution, we have constructed the rheological model of the lithosphere in the area. We have calculated the strength distribution in the lithosphere and constructed the strength envelopes for both compressional and extensional regimes. The obtained results indicate that the strength steadily decreases from the Western desert through the Eastern desert towards the Red Sea where it reaches its minimum for both compressional and extensional regime. Maximum strength can be observed in the Western desert where the largest strength reaches values of about 250-300 MPa within the upper crust on the boundary between upper and lower crust. In the Eastern desert we observe slightly decreased strength with max values about 200-250 MPa within upper crust within 15 km with compression being dominant. These results suggest mostly rigid deformation in the region or Western and Eastern desert. In the Red Sea, the strength rapidly decreases to its minimum suggesting ductile processes as a result of higher temperatures.

Evaluation of the wound-healing activity of Hibiscus rosa sinensis L (Malvaceae) in Wistar albino rats.

PubMed

Bhaskar, Anusha; Nithya, V

2012-01-01

To investigate the wound-healing potency of the ethanolic extract of the flowers of Hibiscus rosa sinensis. The wound-healing activity of H. rosa sinensis (5 and 10% w/w) on Wistar albino rats was studied using three different models viz., excision, incision and dead space wound. The parameters studied were breaking strength in incision model, granulation tissue dry weight, breaking strength and collagen content in dead space wound model, percentage of wound contraction and period of epithelization in excision wound model. The granulation tissue formed on days 4, 8, 12, and 16 (post-wound) was used to estimate total collagen, hexosamine, protein, DNA and uronic acid. Data were analyzed by Analysis of Variance (ANOVA) test. P<0.05 was considered statistically significant. The extract increased cellular proliferation and collagen synthesis at the wound site, as evidenced by increase in DNA, total protein and total collagen content of granulation tissues. The extract-treated wounds were found to heal much faster as indicated by improved rates of epithelialization and wound contraction. The extract of H. rosa sinensis significantly (P<0.001) increased the wound-breaking strength in the incision wound model compared to controls. The extract-treated wounds were found to epithelialize faster, and the rate of wound contraction was significantly (P<0.001) increased as compared to control wounds. Wet and dry granulation tissue weights in a dead space wound model increased significantly (P<0.001). There was a significant increase in wound closure rate, tensile strength, dry granuloma weight, wet granuloma weight and decrease in epithelization period in H. rosa sinensis-treated group as compared to control and standard drug-treated groups. The ethanolic extract of H. rosa sinensis had greater wound-healing activity than the nitrofurazone ointment.

What to Do if a Compact Fluorescent Light (CFL) Bulb or Fluorescent Tube Light Bulb Breaks: Printable Instructions

EPA Pesticide Factsheets

The broken bulb can continue to release mercury vapor until it is cleaned up and removed. This cleanup guidance represents minimum recommended actions to reduce mercury exposure, and will be updated as more efficient practices are identified.

Wave-induced stress and breaking of sea ice in a coupled hydrodynamic discrete-element wave-ice model

NASA Astrophysics Data System (ADS)

Herman, Agnieszka

2017-11-01

In this paper, a coupled sea ice-wave model is developed and used to analyze wave-induced stress and breaking in sea ice for a range of wave and ice conditions. The sea ice module is a discrete-element bonded-particle model, in which ice is represented as cuboid grains floating on the water surface that can be connected to their neighbors by elastic joints. The joints may break if instantaneous stresses acting on them exceed their strength. The wave module is based on an open-source version of the Non-Hydrostatic WAVE model (NHWAVE). The two modules are coupled with proper boundary conditions for pressure and velocity, exchanged at every wave model time step. In the present version, the model operates in two dimensions (one vertical and one horizontal) and is suitable for simulating compact ice in which heave and pitch motion dominates over surge. In a series of simulations with varying sea ice properties and incoming wavelength it is shown that wave-induced stress reaches maximum values at a certain distance from the ice edge. The value of maximum stress depends on both ice properties and characteristics of incoming waves, but, crucially for ice breaking, the location at which the maximum occurs does not change with the incoming wavelength. Consequently, both regular and random (Jonswap spectrum) waves break the ice into floes with almost identical sizes. The width of the zone of broken ice depends on ice strength and wave attenuation rates in the ice.

Heterogeneous autoregressive model with structural break using nearest neighbor truncation volatility estimators for DAX.

PubMed

Chin, Wen Cheong; Lee, Min Cherng; Yap, Grace Lee Ching

2016-01-01

High frequency financial data modelling has become one of the important research areas in the field of financial econometrics. However, the possible structural break in volatile financial time series often trigger inconsistency issue in volatility estimation. In this study, we propose a structural break heavy-tailed heterogeneous autoregressive (HAR) volatility econometric model with the enhancement of jump-robust estimators. The breakpoints in the volatility are captured by dummy variables after the detection by Bai-Perron sequential multi breakpoints procedure. In order to further deal with possible abrupt jump in the volatility, the jump-robust volatility estimators are composed by using the nearest neighbor truncation approach, namely the minimum and median realized volatility. Under the structural break improvements in both the models and volatility estimators, the empirical findings show that the modified HAR model provides the best performing in-sample and out-of-sample forecast evaluations as compared with the standard HAR models. Accurate volatility forecasts have direct influential to the application of risk management and investment portfolio analysis.

Odor Control Test Plan of the Urine Containment Bag (UCB) for Orion Utilization

NASA Technical Reports Server (NTRS)

Casper, Stephanie; Williams, Nicole M. M.

2010-01-01

The purpose of this test is to evaluate the odor containment of the urine containment bag (UCB), P/N SDD46107234-306 in an environment simulating a spacecraft capsule. The goal is to determine the time of odor break through and the acceptability of the odor, once break through occurs. The goal is to simulate, as close as possible, the volume ratio (trash to free volume), trash content (vomit, urine, feces, and food trash), humidity and temperature of the capsule. The goal for minimum break through is 48 hours (Orion Block 0) from the start of the test. The goal for acceptability of odor is 2 weeks (including docked ISS time for Orion Block 0). Two UCB's will be tested simultaneously in different chambers. The one UCB will be tested empty, serving as a control. Odor break through will be based upon the when the filled UCB total organics exceeds that of the control (empty UCB) by a level detectable by a human panel (approximately 2 ppm).

Friction Stir Weld Restart+Reweld Repair Allowables

NASA Technical Reports Server (NTRS)

Clifton, Andrew

2008-01-01

A friction stir weld (FSW) repair method has been developed and successfully implemented on Al 2195 plate material for the Space Shuttle External Fuel Tank (ET). The method includes restarting the friction stir weld in the termination hole of the original weld followed by two reweld passes. Room temperature and cryogenic temperature mechanical properties exceeded minimum FSW design strength and compared well with the development data. Simulated service test results also compared closely to historical data for initial FSW, confirming no change to the critical flaw size or inspection requirements for the repaired weld. Testing of VPPA fusion/FSW intersection weld specimens exhibited acceptable strength and exceeded the minimum design value. Porosity, when present at the intersection was on the root side toe of the fusion weld, the "worst case" being 0.7 inch long. While such porosity may be removed by sanding, this "worst case" porosity condition was tested "as is" and demonstrated that porosity did not negatively affect the strength of the intersection weld. Large, 15-inch "wide panels" FSW repair welds were tested to demonstrate strength and evaluate residual stresses using photo stress analysis. All results exceeded design minimums, and photo stress analysis showed no significant stress gradients due to the presence of the restart and multi-pass FSW repair weld.

From breaking point to breakthrough during the ICU stay: A qualitative study of family members' experiences of long-term intensive care patients' pathways towards survival.

PubMed

Haugdahl, Hege S; Eide, Regina; Alexandersen, Ingeborg; Paulsby, Tove Engan; Stjern, Berit; Lund, Stine Borgen; Haugan, Gørill

2018-05-18

To explore family members' experiences of long-term intensive care unit (ICU) patients' pathways towards survival and to highlight family members' efforts to promote the patient's health during the ICU stay. Although considerable research has been devoted to the substantial burden of long-term ICU patients, less attention has been paid to health promoting factors that facilitate patients' health and survival during ICU stays. Support from family members can improve patient outcome. However, there is little knowledge of the specific contributions provided by family members. A hermeneutic phenomenological approach, within the context of Antonovsky's salutogenic theory and Merleau-Ponty's phenomenology of the body, involving the body as the fundament of experience and understanding. In-depth qualitative interviews. Thirteen family members of long-term ICU patients were interviewed once, at six to 18 months after ICU discharge. The consolidated criteria for reporting qualitative research were used. Three themes were identified: (1) A body at a breaking point; (2) Family members' presence and; (3) Breaking through. In the perspective of the family members, their beloved ones were at a breaking point between life and death. The family's presence was significantly health promoting, demonstrating and communicating love and sensitivity. Moreover, family members' understanding of the patient's unique characteristics and personality was crucial to the patient's experience of being understood, recognized and acknowledged. Inner strength represented a life force capable of moving the patient from the breaking point towards a breakthrough towards life. Family members purposely used their knowledge about the patient to trigger, nurture and release the patient's inner strength. Family presence helps to trigger, arouse and release a patient's inner strength, representing important health promoting factors facilitating patients' health and survival during an ICU stay. Insights into tThe unique and vital health promoting influence of family participation indicate the responsibility of the ICU team to provide support for families. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

7 CFR 993.97 - Exhibit A; minimum standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... condition; (3) end cracks; (4) fermentation; (5) skin or flesh damage; (6) scab; (7) burned; (8) mold; (9... substantially affected. (3) End cracks means callous growth cracks, at the blossom end of prunes, aggregating... flavor is substantially affected. (5) Skin or flesh damage means growth cracks, splits, breaks in skin or...

Point sensitive NMR imaging system using a magnetic field configuration with a spatial minimum

DOEpatents

Eberhard, Philippe H.

1985-01-01

A point-sensitive NMR imaging system (10) in which a main solenoid coil (11) produces a relatively strong and substantially uniform magnetic field and a pair of perturbing coils (PZ1 and PZ2) powered by current in the same direction superimposes a pair of relatively weak perturbing fields on the main field to produce a resultant point of minimum field strength at a desired location in a direction along the Z-axis. Two other pairs of perturbing coils (PX1, PX2; PY1, PY2) superimpose relatively weak field gradients on the main field in directions along the X- and Y-axes to locate the minimum field point at a desired location in a plane normal to the Z-axes. An RF generator (22) irradiates a tissue specimen in the field with radio frequency energy so that desired nuclei in a small volume at the point of minimum field strength will resonate.

Dynamic fracture toughness of ASME SA508 Class 2a ASME SA533 grade A Class 2 base and heat affected zone material and applicable weld metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logsdon, W.A.; Begley, J.A.; Gottshall, C.L.

1978-03-01

The ASME Boiler and Pressure Vessel Code, Section III, Article G-2000, requires that dynamic fracture toughness data be developed for materials with specified minimum yield strengths greater than 50 ksi to provide verification and utilization of the ASME specified minimum reference toughness K/sub IR/ curve. In order to qualify ASME SA508 Class 2a and ASME SA533 Grade A Class 2 pressure vessel steels (minimum yield strengths equal 65 kip/in./sup 2/ and 70 kip/in./sup 2/, respectively) per this requirement, dynamic fracture toughness tests were performed on these materials. All dynamic fracture toughness values of SA508 Class 2a base and HAZ material,more » SA533 Grade A Class 2 base and HAZ material, and applicable weld metals exceeded the ASME specified minimum reference toughness K/sub IR/ curve.« less

The chiral magnetic effect and chiral symmetry breaking in SU(3) quenched lattice gauge theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braguta, V. V., E-mail: braguta@mail.ru; Buividovich, P. V., E-mail: buividovich@itep.ru; Kalaydzhyan, T., E-mail: tigran.kalaydzhyan@desy.de

2012-04-15

We study some properties of the non-Abelian vacuum induced by strong external magnetic field. We perform calculations in the quenched SU(3) lattice gauge theory with tadpole-improved Luescher-Weisz action and chirally invariant lattice Dirac operator. The following results are obtained: The chiral symmetry breaking is enhanced by the magnetic field. The chiral condensate depends on the strength of the applied field as a power function with exponent {nu} = 1.6 {+-} 0.2. There is a paramagnetic polarization of the vacuum. The corresponding susceptibility and other magnetic properties are calculated and compared with the theoretical estimations. There are nonzero local fluctuations ofmore » the chirality and electromagnetic current, which grow with the magnetic field strength. These fluctuations can be a manifestation of the Chiral Magnetic Effect.« less

Esophageal mucosal breaks in gastroesophageal reflux disease partially responsive to proton pump inhibitor therapy.

PubMed

Shaheen, Nicholas J; Denison, Hans; Björck, Karin; Silberg, Debra G

2013-04-01

Approximately 20-30% of patients with gastroesophageal reflux disease (GERD) do not experience complete symptom resolution during proton pump inhibitor (PPI) therapy. The aim of this study was to determine the prevalence of esophageal mucosal breaks among patients who have a partial response to PPI therapy. This was an analysis of data from a phase 2b clinical trial carried out to assess the efficacy and safety of a reflux inhibitor, lesogaberan (AZD3355), as an add-on to PPI therapy in this patient population (clinicaltrials.gov reference: NCT01005251). A total of 661 patients with persistent GERD symptoms who had received a minimum of 4 weeks of PPI therapy were included in the study. The prevalence of esophageal mucosal breaks was assessed according to (i) the most recent endoscopy results from within the previous 24 months, if available ("historical" endoscopies), and (ii) the results of endoscopies performed at study baseline ("baseline" endoscopies). Baseline endoscopies were not carried out in patients who had a historical endoscopy showing an absence of esophageal mucosal breaks. Historical endoscopy results were available for 244 patients, of whom 48 (19.7%) had esophageal mucosal breaks. Baseline endoscopies were carried out in 465 patients, of whom 146 (31.4%) had esophageal mucosal breaks. Sensitivity analyses showed a prevalence of esophageal mucosal breaks of 20-30%. In both the historical and baseline endoscopies, most esophageal mucosal breaks were Los Angeles grades A or B. In patients with GERD symptoms partially responsive to PPI therapy, mild-to-moderate severity esophageal mucosal breaks are common (prevalence 20-30%), and may contribute to symptom etiology.

Enhancement of mechanical properties of 3D printed hydroxyapatite by combined low and high molecular weight polycaprolactone sequential infiltration.

PubMed

Suwanprateeb, Jintamai; Thammarakcharoen, Faungchat; Hobang, Nattapat

2016-11-01

A new infiltration technique using a combination of low and high molecular weight polycaprolactone (PCL) in sequence was developed as a mean to improve the mechanical properties of three dimensional printed hydroxyapatite (HA). It was observed that using either high (M n ~80,000) or low (M n ~10,000) molecular weight infiltration could only increase the flexural modulus compared to non-infiltrated HA, but did not affect strength, strain at break and energy at break. In contrast, a combination of low and high molecular infiltration in sequence increased the flexural modulus, strength and energy at break compared to those of non-infiltrated HA or infiltrated by high or low molecular weight PCL alone. This overall enhancement was found to be attributed to the densification of low molecular weight PCL and the reinforcement of high molecular PCL concurrently. The combined low and high molecular weight infiltration in sequence also maintained high osteoblast proliferation and differentiation of the composites at the similar level of the HA. Densification was a dominant mechanism for the change in modulus with porosity and density of the infiltrated HA/PCL composites. However, both densification and the reinforcing performance of the infiltration phase were crucial for strength and toughening enhancement of the composites possibly by the defect healing and stress shielding mechanisms. The sequence of using low molecular weight infiltration and followed by high molecular infiltration was seen to provide the greatest flexural properties and highest cells proliferation and differentiation capabilities.

Mechanical Reinforcement of Epoxy Composites with Carbon Fibers and HDPE

NASA Astrophysics Data System (ADS)

He, R.; Chang, Q.; Huang, X.; Li, J.

2018-01-01

Silanized carbon fibers (CFs) and a high-density polyethylene with amino terminal groups (HDPE) were introduced into epoxy resins to fabricate high-performance composites. A. mechanical characterization of the composites was performed to investigate the effect of CFs in cured epoxy/HDPE systems. The composites revealed a noticeable improvement in the tensile strength, elongation at break, flexural strength, and impact strength in comparison with those of neat epoxy and cured epoxy/HDPE systems. SEM micrographs showed that the toughening effect could be explained by yield deformations, phase separation, and microcracking.

Gravity signatures of terrane accretion

NASA Astrophysics Data System (ADS)

Franco, Heather; Abbott, Dallas

1999-01-01

In modern collisional environments, accreted terranes are bracketed by forearc gravity lows, a gravitational feature which results from the abandonment of the original trench and the initiation of a new trench seaward of the accreted terrane. The size and shape of the gravity low depends on the type of accreted feature and the strength of the formerly subducting plate. Along the Central American trench, the accretion of Gorgona Island caused a seaward trench jump of 48 to 66 km. The relict trench axes show up as gravity lows behind the trench with minimum values of -78 mgal (N of Gorgona) and -49 mgal (S of Gorgona) respectively. These forearc gravity lows have little or no topographic expression. The active trench immediately seaward of these forearc gravity lows has minimum gravity values of -59 mgal (N of Gorgona) and -58 mgal (S of Gorgona), respectively. In the north, the active trench has a less pronounced gravity low than the sediment covered forearc. In the Mariana arc, two Cretaceous seamounts have been accreted to the Eocene arc. The northern seamount is most likely a large block, the southern seamount may be a thrust slice. These more recent accretion events have produced modest forearc topographic and gravity lows in comparison with the topographic and gravity lows within the active trench. However, the minimum values of the Mariana forearc gravity lows are modest only by comparison to the Mariana Trench (-216 mgal); their absolute values are more negative than at Gorgona Island (-145 to -146 mgal). We speculate that the forearc gravity lows and seaward trench jumps near Gorgona Island were produced by the accretion of a hotspot island from a strong plate. The Mariana gravity lows and seaward trench jumps (or thrust slices) were the result of breaking a relatively weak plate close to the seamount edifice. These gravity lows resulting from accretion events should be preserved in older accreted terranes.

High-scale SUSY from an R -invariant new inflation in the landscape

NASA Astrophysics Data System (ADS)

Kawasaki, Masahiro; Yamada, Masaki; Yanagida, Tsutomu T.; Yokozaki, Norimi

2016-03-01

We provide an anthropic reason for the supersymmetry breaking scale being much higher than the electroweak scale, as indicated by the null result of collider experiments and the observed 125 GeV Higgs boson. We focus on a new inflation model as a typical low-scale inflation model that may be expected in the string landscape. In this model, R symmetry is broken at the minimum of the inflaton potential, and its breaking scale is related to the reheating temperature. Once we admit that the anthropic principle requires thermal leptogenesis, we obtain a lower bound for the gravitino mass, which is related to the R symmetry breaking scale. This scenario and resulting gravitino mass predict the consistent amplitude of density perturbations. We also find that string axions and saxions are consistently implemented in this scenario.

Investigation of the physical properties, antioxidant and antimicrobial activity of ternary potato starch-furcellaran-gelatin films incorporated with lavender essential oil.

PubMed

Jamróz, Ewelina; Juszczak, Lesław; Kucharek, Mateusz

2018-07-15

Lavender essential oil (OEL) was added to starch, furcellaran and gelatin (S/F/G) films in concentrations of 2%, 4% and 6%. The films were examined in terms of physical properties (thickness, density, water solubility, water absorption and degree of swelling) and mechanical properties (tensile strength, elongation at break). The test results show that the film thickness increased upon addition of OEL. The solubility, water absorption and degree of swelling of the film decreased with increasing concentration of oils. Tensile strength (TS) decreased considerably with increasing concentration of oil, which resulted in lower mechanical strength. Parameters of elongation at break (EAB) were not changed. The thermal behaviour of the film was affected by OEL. Possible interaction between film matrix and lavender oil was confirmed using FTIR. Antioxidant properties proved to be significantly enhanced with increasing OEL concentration. The microbiological analysis confirmed antimicrobial properties of S/F/G with OEL. S/F/G films with OEL can provide new formulation of active packaging with potential food-technology applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Nambu-Jona-Lasinio model in a parallel electromagnetic field

NASA Astrophysics Data System (ADS)

Wang, Lingxiao; Cao, Gaoqing; Huang, Xu-Guang; Zhuang, Pengfei

2018-05-01

We explore the features of the UA (1) and chiral symmetry breaking of the Nambu-Jona-Lasinio model without the Kobayashi-Maskawa-'t Hooft determinant term in the presence of a parallel electromagnetic field. We show that the electromagnetic chiral anomaly can induce both finite neutral pion condensate and isospin-singlet pseudo-scalar η condensate and thus modifies the chiral symmetry breaking pattern. In order to characterize the strength of the UA (1) symmetry breaking, we evaluate the susceptibility associated with the UA (1) charge. The result shows that the susceptibility contributed from the chiral anomaly is consistent with the behavior of the corresponding η condensate. The spectra of the mesonic excitations are also studied.

Estimated Effects of Different Alcohol Taxation and Price Policies on Health Inequalities: A Mathematical Modelling Study.

PubMed

Meier, Petra S; Holmes, John; Angus, Colin; Ally, Abdallah K; Meng, Yang; Brennan, Alan

2016-02-01

While evidence that alcohol pricing policies reduce alcohol-related health harm is robust, and alcohol taxation increases are a WHO "best buy" intervention, there is a lack of research comparing the scale and distribution across society of health impacts arising from alternative tax and price policy options. The aim of this study is to test whether four common alcohol taxation and pricing strategies differ in their impact on health inequalities. An econometric epidemiological model was built with England 2014/2015 as the setting. Four pricing strategies implemented on top of the current tax were equalised to give the same 4.3% population-wide reduction in total alcohol-related mortality: current tax increase, a 13.4% all-product duty increase under the current UK system; a value-based tax, a 4.0% ad valorem tax based on product price; a strength-based tax, a volumetric tax of £0.22 per UK alcohol unit (= 8 g of ethanol); and minimum unit pricing, a minimum price threshold of £0.50 per unit, below which alcohol cannot be sold. Model inputs were calculated by combining data from representative household surveys on alcohol purchasing and consumption, administrative and healthcare data on 43 alcohol-attributable diseases, and published price elasticities and relative risk functions. Outcomes were annual per capita consumption, consumer spending, and alcohol-related deaths. Uncertainty was assessed via partial probabilistic sensitivity analysis (PSA) and scenario analysis. The pricing strategies differ as to how effects are distributed across the population, and, from a public health perspective, heavy drinkers in routine/manual occupations are a key group as they are at greatest risk of health harm from their drinking. Strength-based taxation and minimum unit pricing would have greater effects on mortality among drinkers in routine/manual occupations (particularly for heavy drinkers, where the estimated policy effects on mortality rates are as follows: current tax increase, -3.2%; value-based tax, -2.9%; strength-based tax, -6.1%; minimum unit pricing, -7.8%) and lesser impacts among drinkers in professional/managerial occupations (for heavy drinkers: current tax increase, -1.3%; value-based tax, -1.4%; strength-based tax, +0.2%; minimum unit pricing, +0.8%). Results from the PSA give slightly greater mean effects for both the routine/manual (current tax increase, -3.6% [95% uncertainty interval (UI) -6.1%, -0.6%]; value-based tax, -3.3% [UI -5.1%, -1.7%]; strength-based tax, -7.5% [UI -13.7%, -3.9%]; minimum unit pricing, -10.3% [UI -10.3%, -7.0%]) and professional/managerial occupation groups (current tax increase, -1.8% [UI -4.7%, +1.6%]; value-based tax, -1.9% [UI -3.6%, +0.4%]; strength-based tax, -0.8% [UI -6.9%, +4.0%]; minimum unit pricing, -0.7% [UI -5.6%, +3.6%]). Impacts of price changes on moderate drinkers were small regardless of income or socioeconomic group. Analysis of uncertainty shows that the relative effectiveness of the four policies is fairly stable, although uncertainty in the absolute scale of effects exists. Volumetric taxation and minimum unit pricing consistently outperform increasing the current tax or adding an ad valorem tax in terms of reducing mortality among the heaviest drinkers and reducing alcohol-related health inequalities (e.g., in the routine/manual occupation group, volumetric taxation reduces deaths more than increasing the current tax in 26 out of 30 probabilistic runs, minimum unit pricing reduces deaths more than volumetric tax in 21 out of 30 runs, and minimum unit pricing reduces deaths more than increasing the current tax in 30 out of 30 runs). Study limitations include reducing model complexity by not considering a largely ineffective ban on below-tax alcohol sales, special duty rates covering only small shares of the market, and the impact of tax fraud or retailer non-compliance with minimum unit prices. Our model estimates that, compared to tax increases under the current system or introducing taxation based on product value, alcohol-content-based taxation or minimum unit pricing would lead to larger reductions in health inequalities across income groups. We also estimate that alcohol-content-based taxation and minimum unit pricing would have the largest impact on harmful drinking, with minimal effects on those drinking in moderation.

Stable SU(5) monopoles with higher magnetic charge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miyamoto, S.; Sato, H.; Tomohiro, S.

1985-09-15

Taking into account the electroweak breaking effects, some multiply charged monopoles were shown to be stable by Gardner and Harvey. We give the explicit Ansa$uml: tze for finite-energy, nonsingular solutions of these stable higher-strength monopoles with eg = 1,(3/2),3. We also give the general stability conditions and the detailed behavior of the interaction potentials between two monopoles which produce the stable higher-strength monopoles.

High performance concrete in a bridge in Richlands, Virginia

DOT National Transportation Integrated Search

1999-09-01

The Virginia Department of Transportation built a high-performance concrete (HPC) bridge with high-strength and low-permeability concrete in Richlands. The beams had a minimum compressive strength of 69 MPa (10,000 psi) at 28 days and large, 15 mm (0...

Pore geometry as a control on rock strength

NASA Astrophysics Data System (ADS)

Bubeck, A.; Walker, R. J.; Healy, D.; Dobbs, M.; Holwell, D. A.

2017-01-01

The strength of rocks in the subsurface is critically important across the geosciences, with implications for fluid flow, mineralisation, seismicity, and the deep biosphere. Most studies of porous rock strength consider the scalar quantity of porosity, in which strength shows a broadly inverse relationship with total porosity, but pore shape is not explicitly defined. Here we use a combination of uniaxial compressive strength measurements of isotropic and anisotropic porous lava samples, and numerical modelling to consider the influence of pore shape on rock strength. Micro computed tomography (CT) shows that pores range from sub-spherical to elongate and flat ellipsoids. Samples that contain flat pores are weaker if compression is applied parallel to the short axis (i.e. across the minimum curvature), compared to compression applied parallel to the long axis (i.e. across the maximum curvature). Numerical models for elliptical pores show that compression applied across the minimum curvature results in relatively broad amplification of stress, compared to compression applied across the maximum curvature. Certain pore shapes may be relatively stable and remain open in the upper crust under a given remote stress field, while others are inherently weak. Quantifying the shape, orientations, and statistical distributions of pores is therefore a critical step in strength testing of rocks.

The Peculiar Solar Minimum 23/24 Revealed by the Microwave Butterfly Diagram

NASA Technical Reports Server (NTRS)

Gopalswamy, Natchimuthuk; Yashiro, Seiji; Makela, Pertti; Shibasaki, Kiyoto; Hathaway, David

2010-01-01

The diminished polar magnetic field strength during the minimum between cycles 23 and 24 is also reflected in the thermal radio emission originating from the polar chromosphere. During solar minima, the polar corona has extended coronal holes containing intense unipolar flux. In microwave images, the coronal holes appear bright, with a brightness enhancement of 500 to 2000 K with respect to the quiet Sun. The brightness enhancement corresponds to the upper chromosphere, where the plasma temperature is approx.10000 K. We constructed a microwave butterfly diagram using the synoptic images obtained by the Nobeyama radioheliograph (NoRH) showing the evolution of the polar and low latitude brightness temperature. While the polar brightness reveals the chromospheric conditions, the low latitude brightness is attributed to active regions in the corona. When we compared the microwave butterfly diagram with the magnetic butterfly diagram, we found a good correlation between the microwave brightness enhancement and the polar field strength. The microwave butterfly diagram covers part of solar cycle 22, whole of cycle 23, and part of cycle 24, thus enabling comparison between the cycle 23/24 and cycle 22/23 minima. The microwave brightness during the cycle 23/24 minimum was found to be lower than that during the cycle 22/23 minimum by approx.250 K. The reduced brightness temperature is consistent with the reduced polar field strength during the cycle 23/24 minimum seen in the magnetic butterfly diagram. We suggest that the microwave brightness at the solar poles is a good indicator of the speed of the solar wind sampled by Ulysses at high latitudes..

Airfoil profiles for minimum pressure drag at supersonic velocities -- general analysis with application to linearized supersonic flow

NASA Technical Reports Server (NTRS)

Chapman, Dean R

1952-01-01

A theoretical investigation is made of the airfoil profile for minimum pressure drag at zero lift in supersonic flow. In the first part of the report a general method is developed for calculating the profile having the least pressure drag for a given auxiliary condition, such as a given structural requirement or a given thickness ratio. The various structural requirements considered include bending strength, bending stiffness, torsional strength, and torsional stiffness. No assumption is made regarding the trailing-edge thickness; the optimum value is determined in the calculations as a function of the base pressure. To illustrate the general method, the optimum airfoil, defined as the airfoil having minimum pressure drag for a given auxiliary condition, is calculated in a second part of the report using the equations of linearized supersonic flow.

Biocompatibility and strength properties of nitinol shape memory alloy suture in rabbit tendon.

PubMed

Kujala, Sauli; Pajala, Ari; Kallioinen, Matti; Pramila, Antti; Tuukkanen, Juha; Ryhänen, Jorma

2004-01-01

Nitinol (NiTi) is a promising new tendon suture material with good strength, easy handling and good super-elastic properties. NiTi sutures were implanted for biocompatibility testing into the right medial gastrocnemius tendon in 15 rabbits for 2, 6 and 12 weeks. Additional sutures were implanted in subcutaneous tissue for strength measurements in order to determine the effect of implantation on strength properties of NiTi suture material. Braided polyester sutures (Ethibond) of approximately the same diameter were used as control. Encapsulating membrane formation around the sutures was minimal in the case of both materials. The breaking load of NiTi was significantly greater compared to braided polyester. Implantation did not affect the strength properties of either material.

Lodging Resistance of Japonica Rice (Oryza Sativa L.): Morphological and Anatomical Traits due to top-Dressing Nitrogen Application Rates.

PubMed

Zhang, Wujun; Wu, Longmei; Wu, Xiaoran; Ding, Yanfeng; Li, Ganghua; Li, Jingyong; Weng, Fei; Liu, Zhenghui; Tang, She; Ding, Chengqiang; Wang, Shaohua

2016-12-01

Lodging in rice production often limits grain yield and quality by breaking or bending stems. Excessive nitrogen (N) fertilizer rates are the cause of poor lodging resistance in rice, but little is known about the effect of top-dressing N application rates on the mechanical strength of japonica rice plants, especially how the anatomical structure in culms is affected by N. In this study, field experiments on two japonica rice varieties with three top-dressing N application rates, 0 kg N ha(-1) (LN), 135 kg N ha(-1) (MN), and 270 kg N ha(-1) (HN) as urea, were conducted. Wuyunjing23, a lodging-resistant japonica rice cultivar and W3668, a lodging-susceptible japonica rice cultivar were used. The lodging index, breaking strength, morphological and anatomical traits in culms were measured in this study. The visual lodging rate in japonica rice differed remarkably between genotypes and top-dressing N treatments. The higher lodging index of rice plants was primarily attributed to the weak breaking strength of the lower internodes. The longer elongated basal internodes were responsible for higher plant height and a higher lodging index. Correlation analysis showed that breaking strength was significantly and positively correlated with the thickness of the mechanical tissue but was significantly and negatively correlated with the inner diameter of the major axis (b2). With increasing top-dressing N rates, the sclerenchyma cells of the mechanical tissues and the vascular bundles of the Wuyunjing23 cultivar varied little. The plant height, inner diameter of the minor axis (a2) and b2 increased significantly, but the area of the large vascular bundle (ALVB) and the area of the small vascular bundle (ASVB) decreased significantly and resulted in lower stem strength and a higher lodging index under higher top-dressing N conditions. The culm diameter of the W3668 cultivar increased slightly with no significant difference, and the sclerenchyma cells in the mechanical tissues and vascular bundles showed deficient lignifications under high top-dressing N conditions. Moreover, the ALVB and the ASVB decreased significantly, while the area of air chambers (AAC) increased rapidly. An improvement in the lodging resistance of japonica rice plants could be achieved by reducing the length of the lower internodes, decreasing the inner culm diameter and developing a thicker mechanical tissue. Top-dressing N application increased the plant height and inner culm diameter and decreased the ALVB and the ASVB of the Wuyunjing23 cultivar and caused deficient lignified sclerenchyma cells, lowered the ALVB and the ASVB, and increased the AAC of the W3668 cultivar resulting in weaker stem strength and a higher lodging index.

A comparative study of retentive strengths of zinc phosphate, polycarboxylate and glass ionomer cements with stainless steel crowns - an in vitro study.

PubMed

Raghunath Reddy, M H; Subba Reddy, V V; Basappa, N

2010-01-01

An in vitro study was conducted to compare the retentive strengths of zinc phosphate, polycarboxylate and glass ionomer cements using Instron universal testing machine. Thirty preformed and pretrimmed stainless steel crowns were used for cementation on 30 extracted human primary molars which were divided into three groups of 10 teeth in each group. Then the teeth were stored in artificial saliva and incubated at 37°C for 24 h. A load was applied on to the crown and was gradually increased till the crown showed dislodgement, and then the readings were recorded using Instron recorder and analyzed for statistical significance. The surface area of crown was measured by graphical method. The retentive strength was expressed in terms of kg/cm 2 , which was calculated by the equation load divided by area. Retentive strengths of zinc phosphate (ranged from a minimum of 16.93 to amaximum of 28.13 kg/cm 2 with mean of 21.28 kg/cm 2 ) and glass ionomer cement (minimum of 13.69 - 28.15 kg/cm 2 with mean of 20.69 kg/cm 2 ) were greater than that of polycarboxylate cement (minimum of 13.26 - 22.69 kg/cm 2 with mean of 16.79 kg/cm 2 ). Negligible difference (0.59 kg/cm 2 ) of retentive strength was observed between zinc phosphate (21.28 kg/cm 2 ) and glass ionomer cements (20.69 kg/cm 2 ). Glass ionomer cements can be recommended for cementation of stainless steel crowns because of its advantages and the retentive strength was almost similar to that of zinc phosphate cement.

Investigating Hastily-Formed Collaborative Networks

DTIC Science & Technology

2007-03-01

support a minimum range of 250 meters since this is the minimum required length of a fire hose . • Jurisdiction Area Network (JAN): This is the main...but typical braided one-half inch polypropylene rope weighs less than two pounds per one hundred 4-19 feet and has tensile strengths greater than two

25 CFR 542.11 - What are the minimum internal control standards for pari-mutuel wagering?

Code of Federal Regulations, 2011 CFR

2011-04-01

...; (ii) Gaming operation name (or identification number) and station number; (iii) Race track, race number, horse identification or event identification, as applicable; (iv) Type of bet(s), each bet amount... wagering on race events while on duty, including during break periods. (g) Computer reports standards. (1...

Isospin-symmetry breaking in masses of N ≃ Z nuclei

NASA Astrophysics Data System (ADS)

Bączyk, P.; Dobaczewski, J.; Konieczka, M.; Satuła, W.; Nakatsukasa, T.; Sato, K.

2018-03-01

Effects of the isospin-symmetry breaking (ISB) beyond mean-field Coulomb terms are systematically studied in nuclear masses near the N = Z line. The Coulomb exchange contributions are calculated exactly. We use extended Skyrme energy density functionals (EDFs) with proton-neutron-mixed densities, to which we add new terms breaking the isospin symmetry. Two parameters associated with the new terms are determined by fitting mirror and triplet displacement energies (MDEs and TDEs) of isospin multiplets. The new EDFs reproduce MDEs for the T = 1/2 doublets and T = 1 triplets, and TDEs for the T = 1 triplets. Relative strengths of the obtained isospin-symmetry-breaking terms are not consistent with the differences in the NN scattering lengths, ann, app, and anp. Based on low-energy experimental data, it seems thus impossible to delineate the strong-force ISB effects from beyond-mean-field Coulomb-energy corrections.

The decoupling of the glass transitions in the two-component p-spin spherical model

NASA Astrophysics Data System (ADS)

Ikeda, Harukuni; Ikeda, Atsushi

2016-07-01

Binary mixtures of large and small particles with a disparate size ratio exhibit a rich phenomenology at their glass transition points. In order to gain insights on such systems, we introduce and study a two-component version of the p-spin spherical spin glass model. We employ the replica method to calculate the free energy and the phase diagram. We show that when the strengths of the interactions of each component are not widely separated, the model has only one glass phase characterized by the conventional one-step replica symmetry breaking. However when the strengths of the interactions are well separated, the model has three glass phases depending on the temperature and component ratio. One is the ‘single’ glass phase in which only the spins of one component are frozen while the spins of the other component remain mobile. This phase is characterized by the one-step replica symmetry breaking. The second is the ‘double’ glass phase obtained by cooling the single glass phase further, in which the spins of the remaining mobile component are also frozen. This phase is characterized by the two-step replica symmetry breaking. The third is also the ‘double’ glass phase, which, however, is formed by the simultaneous freezing of the spins of both components at the same temperatures and is characterized by the one-step replica symmetry breaking. We discuss the implications of these results for the glass transitions of binary mixtures.

46 CFR 96.35-5 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... by reference, see § 96.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

46 CFR 96.35-5 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... by reference, see § 96.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

46 CFR 96.35-5 - General.

Code of Federal Regulations, 2014 CFR

2014-10-01

... by reference, see § 96.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

46 CFR 96.35-5 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... by reference, see § 96.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

Mechanical, Optical, and Barrier Properties of Soy Protein Film As Affected by Phenolic Acid Addition.

PubMed

Insaward, Anchana; Duangmal, Kiattisak; Mahawanich, Thanachan

2015-11-04

This study aimed to explore the effect of phenolic acid addition on properties of soy protein film. Ferulic (FE), caffeic (CA), and gallic (GA) acids as well as their oxidized products were used in this study. Phenolic acid addition was found to have a significant effect (p ≤ 0.05) on the mechanical properties of the film. GA-containing films exhibited the highest tensile strength and elongation at break, followed by those with added CA and FE, respectively. Oxidized phenolic acids were shown to produce a film with higher tensile strength and elongation at break than their unoxidized counterparts. Phenolic acid addition also affected film color and transparency. As compared to the control, phenolic-containing film samples demonstrated reduced water vapor permeability and water solubility and increased contact angle, especially at high concentrations of oxidized phenolic acid addition.

Concentrated autologous plasma protein: a biochemically neutral solder for tissue welding.

PubMed

Stewart, R B; Bleustein, C B; Petratos, P B; Chin, K C; Poppas, D P; Kung, R T

2001-01-01

Xenographic or allographic serum protein solders used for laser welding may have immunologic and/or pathogenic complications. The objective of these studies was to develop a safe, autologous solder. Five methods of preparing concentrated autologous plasma protein solder (CAPPS) were evaluated. Next, the CAPPS was evaluated via (1) thermal denaturation studies using differential scanning calorimetry, (2) tissue welding studies to characterize both acute and healing properties. The optimal concentration method to produce CAPPS rapidly was a dialysis method using chemical (osmotic) forces. The CAPPS showed similar denaturation profiles to serum albumin (SA) solders. Acutely, CAPPS provided comparable breaking strengths to SA solders. At 7 days, there was no significant difference in breaking strength or histology between 50% human SA solder and CAPPS (using a porcine skin model). These studies demonstrate that the CAPPS system provides acceptable acute and chronic properties for laser welding. Copyright 2001 Wiley-Liss, Inc.

Enhancement of the interface in poly(L-lactide) and poly(propylidene carbonate) blends by introducing of poly(L-lactide)-grafted graphene oxide to improve mechanical properties

NASA Astrophysics Data System (ADS)

Li, Qi; Qin, Shengxue; Tian, Xiujuan; Chen, Xueyang; Chen, Yunlei; Niu, Yanhua; Zhao, Lifen

2018-03-01

Enhancement of the interfacial structure has great significances in achieving polymer blends with high mechanical performance. To improve the mechanical properties of poly(L-lactide) (PLLA)/poly(propylidene carbonate) (PPC) blends, the covalent functionalized graphene oxide by PLLA chains (PLLA-g-GO) was synthesized by a two-step strategy. It could migrate from the thermally preferred PPC phase to the interfaces of PLLA and PPC and promote the formation of a network-like structure. As a consequence, the tensile strength and elongation at break were both improved. Furthermore, the PLLA-g-GO located at the interface could induce the crystallization at the boundary, which brought the significant improvement of the tensile strength and elongation at break. This result may be beneficial for designing high-performance PLLA materials.

Dynamical Evolution of an Effective Two-Level System with {\\mathscr{P}}{\\mathscr{T}} Symmetry

NASA Astrophysics Data System (ADS)

Du, Lei; Xu, Zhihao; Yin, Chuanhao; Guo, Liping

2018-05-01

We investigate the dynamics of parity- and time-reversal (PT ) symmetric two-energy-level atoms in the presence of two optical and a radio-frequency (rf) fields. The strength and relative phase of fields can drive the system from unbroken to broken PT symmetric regions. Compared with the Hermitian model, Rabi-type oscillation is still observed, and the oscillation characteristics are also adjusted by the strength and relative phase in the region of unbroken PT symmetry. At exception point (EP), the oscillation breaks down. To better understand the underlying properties we study the effective Bloch dynamics and find the emergence of the z components of the fixed points is the feature of the PT symmetry breaking and the projections in x-y plane can be controlled with high flexibility compared with the standard two-level system with PT symmetry. It helps to study the dynamic behavior of the complex PT symmetric model.

Effect of Filler Content and Chemical Modification on Mechanical Properties of Polylactic Acid/Polymethyl Methacrylate/Nypa Fruticans Husk Biocomposites

NASA Astrophysics Data System (ADS)

Mohamad Syahmie, MR; Pei Leng, T.; Nurul Najwa, Zabidi

2018-03-01

The main purpose of incorporating Nypa fruticans husks (NFH) into Polylactic acid (PLA)/Polymethylmethacrylate (PMMA) is to decrease the costs and enhanced the properties of the biocomposites. 3-Aminopropyl Triethoxysilane (3-APE) was used as coupling agent. The effect of NFH content and 3-APE on the mechanical properties and morphology of the biocomposites were investigated. Results show that the effect of NFH content increased Young’s modulus but decreased the tensile strength and elongation at break of PLA/PMMA/NFH biocomposites. However, silanized biocomposites using 3-APE) was found to enhanced the tensile strength and Young’s modulus but decreased the elongation at break of the silanized biocomposites. Scanning electron microscopy (SEM) study of the tensile fracture surface of the biocomposites indicated that the used of 3-APE as couling agent improved the interfacial interaction netween NFH and PLA/PMMA blends.

Effect of organo clay on curing, mechanical and dielectric properties of NR/SBR blends

NASA Astrophysics Data System (ADS)

Ravikumar, K.; Joseph, Reji; Ravichandran, K.

2018-04-01

Natural rubber (NR) and styrene butadiene rubber (SBR) based elastomeric blends reinforced with organically modified Sodium bentonite clay were prepared by two roll mills. Vulcanization parameters such as minimum and maximum torque values scorch and cure times are measured by Oscillating Disc Rheometer. Mechanical properties such as Tensile strength, modulus at 100%, 200% and 300% elongation and elongation at break and Hardness were measured by Universal testing machine and Durometer Shore A hardness meter respectively. Dielectric properties such as dielectric constant (ε’), dissipation factor (tanδ) and volume resistivity (ρv) were measured at room temperature. The curing studies show that torque values are increasing in NR/SBR blends by increase NR content. The scorch and optimum cure time in NR/SBR blends reinforced organo modified clay was found through increase in the SBR content. This may be due to better processing safety of the NR/SBR blends reinforced with organo modified clay. Mechanical properties show that addition of SBR in blends, tensile strength, elongation modulus increases, but 100% modulus slightly increases and no change was observed in Hardness. Dielectric studies show that dielectric constant of NR and SBR rubbers are almost same, it may due to their non-polar nature. But addition of SBR in NR/SBR blend, dielectric constant gradually increases and maximum value observed at 50/50 ratio. But no considerable change was observed in dissipation factor. Frequency dependant resistivity shows that volume resistivity was not changed with respect to frequency up to 3.5 kHz and beyond that the frequency dependence resistivity was found.

Strength and flexibility properties of advanced ceramic fabrics

NASA Technical Reports Server (NTRS)

Sawko, P. M.; Tran, H. K.

1985-01-01

The mechanical properties of four advanced ceramic fabrics were measured at a temperature range of 23C to 1200C. The fabrics evaluated were silica, high and low-boria content aluminoborosilicate, and silicon carbide. Properties studied included fabric break strengths from room temperature to 1200C, and bending durability after temperature conditioning at 1200C and 1400C. The interaction of the fabric and ceramic insulation was also studied for shrinkage, appearance, bend resistance, and fabric-to-insulation bonding. Based on these tests, the low-boria content aluminoborosilicate fabric retained more strength and fabric durability than the other fabrics studied at high temperature.

Strength and flexibility properties of advanced ceramic fabrics

NASA Technical Reports Server (NTRS)

Sawko, P. M.; Tran, H. K.

1985-01-01

The mechanical properties of four advanced ceramic fabrics are measured at a temperature range of 23 C to 1200 C. The fabrics evaluated are silica, high-and low-boria content aluminoborosilicate, and silicon carbide. Properties studied include fabric break strengths from room temperature to 1200 C, and bending durability after temperature conditioning at 1200 C and 1400 C. The interaction of the fabric and ceramic insulation is also studied for shrinkage, appearance, bend resistance, and fabric-to-insulation bonding. Based on these tests, the low-boria content aluminoborosilicate fabric retains more strength and fabric durability than the other fabrics studied at high temperature.

Observations of the UTLS: An analysis of the double tropopause and its relationship to Rossby waves and the tropopause inversion layer

NASA Astrophysics Data System (ADS)

Peevey, Tanya

The upper troposphere lower stratosphere (UTLS) is a region of minimum temperatures that contains the tropopause. As a transition region between the troposphere and the stratosphere, the UTLS contains various processes that facilitate stratosphere-troposphere exchange (STE) which can redistribute radiatively important species such as water vapor or ozone. One potential marker for STE is the double tropopause (DT). Therefore this study seeks to further understand how DTs form and how they could enhance the current understanding of some STE processes in the UTLS. Using data from the High Resolution Dynamic Limb Sounder (HIRDLS), a data set with high vertical and horizontal resolution, newly discovered DT structures are found over the Pacific and Atlantic oceans that suggest a relationship between the DT and both storm tracks and Rossby waves. The association between DTs and storm tracks is examined by further analyzing the recently discovered and unexpected relationship between the DT and the tropopause inversion layer (TIL) in a developing baroclinic disturbance. Results show an increase in the number of DTs when the lapse rate of the extratropical TIL is less than -2°C/km, i.e. when the TIL is stronger and the local stability is higher. Composites of ERA-Interim DT profiles for three different TIL strengths shows that the vertical motion and relative vorticity both decrease as the TIL increases, which suggests the warm conveyor belt as a mechanism. This is investigated further with a case study analysis of a developing extratropical cyclone in the Pacific Ocean. Additionally, an analysis of DTs in relation to the large scale flow responsible for storm development shows a strong correlation between monthly Rossby wave activity, ozone laminae and DT variability. Further examination shows that if these waves break a DT will be found with a wave breaking event about 30% of the time in the eastern Pacific and eastern Atlantic oceans, both regions of poleward wave breaking. These results highlight a new and more complicated DT structure that is a product of both large scale dynamics and small scale vertical motions, thus adding new information to the current understanding of the UTLS.

A method for predicting the fatigue life of pre-corroded 2024-T3 aluminum from breaking load tests

NASA Astrophysics Data System (ADS)

Gruenberg, Karl Martin

Characterization of material properties is necessary for design purposes and has been a topic of research for many years. Over the last several decades, much progress has been made in identifying metrics to describe fracture mechanics properties and developing procedures to measure the appropriate values. However, in the context of design, there has not been as much success in quantifying the susceptibility of a material to corrosion damage and its subsequent impact on material behavior in the framework of fracture mechanics. A natural next step in understanding the effects of corrosion damage was to develop a link between standard material test procedures and fatigue life in the presence of corrosion. Simply stated, the goal of this investigation was to formulate a cheaper and quicker method for assessing the consequences of corrosion on remaining fatigue life. For this study, breaking load specimens and fatigue specimens of a single nominal gage (0.063″) of aluminum alloy 2024-T3 were exposed to three levels of corrosion. The breaking load specimens were taken from three different material lots, and the fatigue tests were carried out at three stress levels. All failed specimens, both breaking load and fatigue specimens, were examined to characterize the damage state(s) and failure mechanism(s). Correlations between breaking load results and fatigue life results in the presence of corrosion damage were developed using a fracture mechanics foundation and the observed mechanisms of failure. Where breaking load tests showed a decrease in strength due to increased corrosion exposure, the corresponding set of fatigue tests showed a decrease in life. And where breaking load tests from different specimen orientations exhibited similar levels of strength, the corresponding set of fatigue specimens showed similar lives. The spread from shortest to longest fatigue lives among the different corrosion conditions decreased at the higher stress levels. Life predictions based on breaking load data were generally shorter than the experimental lives by an average of 20%. The life prediction methodology developed from this investigation is a very valuable tool for the purpose of assessing material substitution for aircraft designers, alloy differentiation for manufacturers, or inspection intervals and aircraft retirement schedules for aircraft in service.

Propagation and Breaking at High Altitudes of Gravity Waves Excited by Tropospheric Forcing

NASA Technical Reports Server (NTRS)

Prusa, Joseph M.; Smolarkiewicz, Piotr K.; Garcia, Rolando R.

1996-01-01

An anelastic approximation is used with a time-variable coordinate transformation to formulate a two-dimensional numerical model that describes the evolution of gravity waves. The model is solved using a semi-Lagrangian method with monotone (nonoscillatory) interpolation of all advected fields. The time-variable transformation is used to generate disturbances at the lower boundary that approximate the effect of a traveling line of thunderstorms (a squall line) or of flow over a broad topographic obstacle. The vertical propagation and breaking of the gravity wave field (under conditions typical of summer solstice) is illustrated for each of these cases. It is shown that the wave field at high altitudes is dominated by a single horizontal wavelength; which is not always related simply to the horizontal dimension of the source. The morphology of wave breaking depends on the horizontal wavelength; for sufficiently short waves, breaking involves roughly one half of the wavelength. In common with other studies, it is found that the breaking waves undergo "self-acceleration," such that the zonal-mean intrinsic frequency remains approximately constant in spite of large changes in the background wind. It is also shown that many of the features obtained in the calculations can be understood in terms of linear wave theory. In particular, linear theory provides insights into the wavelength of the waves that break at high altitudes, the onset and evolution of breaking. the horizontal extent of the breaking region and its position relative to the forcing, and the minimum and maximum altitudes where breaking occurs. Wave breaking ceases at the altitude where the background dissipation rate (which in our model is a proxy for molecular diffusion) becomes greater than the rate of dissipation due to wave breaking, This altitude, in effect, the model turbopause, is shown to depend on a relatively small number of parameters that characterize the waves and the background state.

The ultraviolet variations of iota Cas

NASA Technical Reports Server (NTRS)

Molnar, M. R.; Mallama, A. D.; Soskey, D. G.; Holm, A. V.

1976-01-01

The Ap variable star iota Cas was observed with the photometers on OAO-2 covering the spectral range 1430-4250 A. The ultraviolet light curves show a double wave with primary minimum and maximum at phase ? 0.00 and 0.35, respectively. Secondary minimum light is at phase ? 0.65 with secondary maximum at phase ? 0.85. The light curves longward of 3150 A vary in opposition to those shortward of this 'null region'. Ground-based coude spectra show that the Fe II and Cr II line strengths have a double-wave variation such that maximum strength occurs at minimum ultraviolet light. We suggest that the strong ultraviolet opacities due to photoionization and line blanketing by these metals may cause the observed photometric variations. We have also constructed an oblique-rotator model which shows iron and chromium lying in a great circle band rather than in circular spots.

49 CFR 179.300-6 - Thickness of plates.

Code of Federal Regulations, 2010 CFR

2010-10-01

....037 Where: d = inside diameter in inches; E = 1.0 welded joint efficiency; P = minimum required bursting pressure in psig; S = minimum tensile strength of plate material in p.s.i. as prescribed in § 179... −d 2) where: d = inside diameter in inches; D = outside diameter in inches; p = tank test pressure in...

Preliminary structural design of composite main rotor blades for minimum weight

NASA Technical Reports Server (NTRS)

Nixon, Mark W.

1987-01-01

A methodology is developed to perform minimum weight structural design for composite or metallic main rotor blades subject to aerodynamic performance, material strength, autorotation, and frequency constraints. The constraints and load cases are developed such that the final preliminary rotor design will satisfy U.S. Army military specifications, as well as take advantage of the versatility of composite materials. A minimum weight design is first developed subject to satisfying the aerodynamic performance, strength, and autorotation constraints for all static load cases. The minimum weight design is then dynamically tuned to avoid resonant frequencies occurring at the design rotor speed. With this methodology, three rotor blade designs were developed based on the geometry of the UH-60A Black Hawk titanium-spar rotor blade. The first design is of a single titanium-spar cross section, which is compared with the UH-60A Black Hawk rotor blade. The second and third designs use single and multiple graphite/epoxy-spar cross sections. These are compared with the titanium-spar design to demonstrate weight savings from use of this design methodology in conjunction with advanced composite materials.

Effect of Age and Caponization on Blood Parameters and Bone Development of Male Native Chickens in Taiwan

PubMed Central

Lin, Cheng-Yung; Hsu, Jenn-Chung; Wan, Tien-Chun

2012-01-01

An experiment was carried out to determine the effect of age and caponization on the development blood and bone characteristics development in male country chickens in Taiwan. A total of two hundred 8-wk-old LRI native chicken cockerels, Taishi meat No.13 from LRI-COA, were used as experimental animals. Cockerels were surgically caponized at 8 wks of age. Twelve birds in each group were bled and dressed from 8 wks to 35 wks of age at 1 to 5 wk intervals. The results indicated that the plasma testosterone concentration was significantly (p<0.05) lower in capons after 12 wks of age (caponized treatment after 4 wks) than that of the intact males. The relative tibia weight, bone breaking strength, cortical thickness, bone ash, bone calcium, bone phosphorus and bone magnesium contents were significantly (p<0.05) higher in intact males, while capons had higher (p<0.05) plasma ionized calcium, inorganic phosphorus and alkaline phosphatase concentration. The plasma testosterone concentration, relative tibia weight, tibia length, breaking strength, cortical thickness, bone ash, calcium, and phosphorus contents of intact males chickens increased significantly (p<0.05) with the advance of age. In addition, the relative tibia weight of capons peaked at 18 wks of age, and declined at 35 wks of age. The bone ash, calcium and phosphorus content increased most after 14 wks of age in male native chickens in Taiwan. Also, tibia length and cortical thickness peaked at 22 wks of age. However, the peak of bone strength was found at 26 wks of age. These findings support the assertion that androgens can directly influence bone composition fluxes in male chickens. Caponization caused a significant increase in bone loss at 4 wks post treatment, which reflected bone cell damage, and demonstrated reductions in the relative tibia weight, breaking strength, cortical thickness, bone ash, calcium, phosphorus and magnesium contents, and increases in plasma ionized calcium, inorganic phosphorus and alkaline phosphatase concentration. PMID:25049655

Evaluation of the wound-healing activity of Hibiscus rosa sinensis L (Malvaceae) in Wistar albino rats

PubMed Central

Bhaskar, Anusha; Nithya, V.

2012-01-01

Objective: To investigate the wound-healing potency of the ethanolic extract of the flowers of Hibiscus rosa sinensis. Materials and Methods: The wound-healing activity of H. rosa sinensis (5 and 10% w/w) on Wistar albino rats was studied using three different models viz., excision, incision and dead space wound. The parameters studied were breaking strength in incision model, granulation tissue dry weight, breaking strength and collagen content in dead space wound model, percentage of wound contraction and period of epithelization in excision wound model. The granulation tissue formed on days 4, 8, 12, and 16 (post-wound) was used to estimate total collagen, hexosamine, protein, DNA and uronic acid. Data were analyzed by Analysis of Variance (ANOVA) test. P<0.05 was considered statistically significant. Results: The extract increased cellular proliferation and collagen synthesis at the wound site, as evidenced by increase in DNA, total protein and total collagen content of granulation tissues. The extract-treated wounds were found to heal much faster as indicated by improved rates of epithelialization and wound contraction. The extract of H. rosa sinensis significantly (P<0.001) increased the wound-breaking strength in the incision wound model compared to controls. The extract-treated wounds were found to epithelialize faster, and the rate of wound contraction was significantly (P<0.001) increased as compared to control wounds. Wet and dry granulation tissue weights in a dead space wound model increased significantly (P<0.001). There was a significant increase in wound closure rate, tensile strength, dry granuloma weight, wet granuloma weight and decrease in epithelization period in H. rosa sinensis-treated group as compared to control and standard drug-treated groups. Conclusion: The ethanolic extract of H. rosa sinensis had greater wound-healing activity than the nitrofurazone ointment. PMID:23248396

26 CFR 1.410(a)-9 - Maternity and paternity absence.

Code of Federal Regulations, 2010 CFR

2010-04-01

... reason of a maternity or paternity absence described in section 410(a)(5)(E)(i) or 411(a)(6)(E)(i) is the... any reason other than a quit, discharge, retirement, or death). The period from July 1, 1987, to June... plan increases the minimum period of consecutive 1-year breaks required to disregard any service (or...

Synthesis of a New Titanate Coupling Agent for the Modification of Calcium Sulfate Whisker in Poly(Vinyl Chloride) Composite

PubMed Central

Yuan, Wenjin; Lu, Yunhua; Xu, Shiai

2016-01-01

A new titanate coupling agent synthesized from polyethylene glycol (PEG), isooctyl alcohol, and phosphorus pentoxide (P2O5) was used for the modification of calcium sulfate whiskers (CSWs) and the preparation of high-performance CSW/poly(vinyl chloride) (PVC) composites. The titanate coupling agent (sTi) and the modified CSWs (sTi–CSW) were characterized by Fourier transform infrared (FTIR) spectroscopy, and the mechanical, dynamic mechanical, and heat resistant properties and thermostability of sTi–CSW/PVC and CSW/PVC composites were compared. The results show that sTi–CSW/PVC composite with 10 wt. % whisker content has the best performance, and its tensile strength, Young’s modulus, elongation at break, break strength, and impact strength are 67.2 MPa, 1926 MPa, 233%, 51.1 MPa, and 12.75 KJ·m−2, with an increase of 20.9%, 11.5%, 145.3%, 24.6%, and 65.4% compared to that of CSW/PVC composite at the same whisker content. As the whisker content increases, the storage modulus increases, the Vicat softening temperature decreases slightly, and the glass transition temperature increases at first and then decreases. PMID:28773748

Resisting tempting foods and smoking behavior: implications from a self-control theory perspective.

PubMed

Shmueli, Dikla; Prochaska, Judith J

2009-05-01

Individuals may desire to diet or restrain from eating certain foods while attempting to quit smoking out of concern for weight gain. However, previous research and clinical tobacco treatment guidelines suggest that concurrent dieting may undermine attempts to quit smoking. The current study applied the self-control strength model, which posits that self-regulation relies on a limited strength that is consumed with use, to test whether resisting tempting sweets would lead to a greater likelihood of subsequent smoking. Participants were 101 cigarette smokers randomly assigned to resist eating either from a tempting plate of sweets or from a plate of less tempting vegetables. All participants were then given a 10-min recess. Whether participants smoked during the break, measured with a breath carbon monoxide sample, served as the primary dependent variable. As predicted, participants who resisted sweets were more likely to smoke during the break (53.2%) than those who resisted vegetables (34.0%), chi2(1, N = 101) = 3.65 p < .05. The findings support the tenets of the self-control strength model and suggest the mechanism by which dietary restraint may harm efforts at quitting smoking.

Evaluation of Candidate Materials for Fines Filter Media in the C2 Canister

DTIC Science & Technology

1992-05-01

Philadelphia PA 19103. (5) Owens - Corning Technical Center, "Breaking Strength", Test Report 48708, October 1, 1990. (6) ASTM F778-88, "Gas Flow...strength per ASTM D1682-64. Appendix A 39 OWENS - CORNING TESTING SERVICES TECHNICAL CENTER, 2790 Columbus Rd. OWENS - CORNING FIBERGLAS CORPORATION Granville... Owens - Corning Testing Services makes no warranty, express or implied, whether of merchantability or fitness for any particular purpose, with respect to

Comparison of acellular dermal matrix and synthetic mesh for lateral chest wall reconstruction in a rabbit model.

PubMed

Holton, Luther H; Chung, Thomas; Silverman, Ronald P; Haerian, Hafez; Goldberg, Nelson H; Burrows, Whitney M; Gobin, Andrea; Butler, Charles E

2007-04-01

Synthetic mesh is used for chest wall reconstruction, but infection or exposure can occur and necessitate removal. Human acellular dermal matrix (AlloDerm) has been used to reconstruct musculofascial defects in the trunk with low infection and herniation rates. AlloDerm may have advantages over synthetic mesh for chest wall reconstruction. This study compared outcomes and repair strengths of AlloDerm to expanded polytetrafluoroethylene mesh used for repair of rib cage defects. A 3 x 3-cm, full-thickness, lateral rib cage defect was created in each rabbit and repaired with expanded polytetrafluoroethylene (n = 8) or acellular dermal matrix (n = 9). At 4 weeks, the animals were euthanized and evaluated for lung herniation/dehiscence, strength of adhesions between the implant and intrapleural structures, and breaking strength of the implant materials and the implant-fascia interface. Tissue sections were analyzed with histologic and immunohistochemical staining to evaluate cellular infiltration and vascularization. No herniation or dehiscence occurred with either material. The incidence and strength of adhesions was similar between materials. The mean breaking strength of the AlloDerm-fascia interface (14.5 +/- 8.9 N) was greater than the expanded polytetrafluoroethylene-fascia interface (8.7 +/- 4.4 N; p = 0.027) and similar to the rib-intercostal-rib interface of the contralateral native chest wall (14.0 +/- 5.6 N). The AlloDerm grafts became infiltrated with cells and vascularized after implantation. AlloDerm used for chest wall reconstruction results in greater implant-defect interface strength than expanded polytetrafluoroethylene. The ability of AlloDerm to become vascularized and remodeled by autologous cells and to resist infection may be advantageous for chest wall reconstruction.

Correlation between strength properties in standard test specimens and molded phenolic parts

NASA Technical Reports Server (NTRS)

Turner, P S; Thomason, R H

1946-01-01

This report describes an investigation of the tensile, flexural, and impact properties of 10 selected types of phenolic molding materials. The materials were studied to see in what ways and to what extent their properties satisfy some assumptions on which the theory of strength of materials is based: namely, (a) isotropy, (b) linear stress-strain relationship for small strains, and (c) homogeneity. The effect of changing the dimensions of tensile and flexural specimens and the span-depth ratio in flexural tests were studied. The strengths of molded boxes and flexural specimens cut from the boxes were compared with results of tests on standard test specimens molded from the respective materials. The nonuniformity of a material, which is indicated by the coefficient of variation, affects the results of tests made with specimens of different sizes and tests with different methods of loading. The strength values were found to depend on the relationship between size and shape of the molded specimen and size and shape of the fillers. The most significant variations observed within a diversified group of materials were found to depend on the orientation of fibrous fillers. Of secondary importance was the dependence of the variability of test results on the pieces of filler incorporated into the molding powder as well as on the size of the piece. Static breaking strength tests on boxes molded from six representative phenolic materials correlated well with falling-ball impact tests on specimens cut from molded flat sheets. Good correlation was obtained with Izod impact tests on standard test specimens prepared from the molding materials. The static breaking strengths of the boxes do not correlate with the results of tensile or flexural tests on standard specimens.

Estimated Effects of Different Alcohol Taxation and Price Policies on Health Inequalities: A Mathematical Modelling Study

PubMed Central

Meier, Petra S.; Holmes, John; Angus, Colin; Ally, Abdallah K.; Meng, Yang; Brennan, Alan

2016-01-01

Introduction While evidence that alcohol pricing policies reduce alcohol-related health harm is robust, and alcohol taxation increases are a WHO “best buy” intervention, there is a lack of research comparing the scale and distribution across society of health impacts arising from alternative tax and price policy options. The aim of this study is to test whether four common alcohol taxation and pricing strategies differ in their impact on health inequalities. Methods and Findings An econometric epidemiological model was built with England 2014/2015 as the setting. Four pricing strategies implemented on top of the current tax were equalised to give the same 4.3% population-wide reduction in total alcohol-related mortality: current tax increase, a 13.4% all-product duty increase under the current UK system; a value-based tax, a 4.0% ad valorem tax based on product price; a strength-based tax, a volumetric tax of £0.22 per UK alcohol unit (= 8 g of ethanol); and minimum unit pricing, a minimum price threshold of £0.50 per unit, below which alcohol cannot be sold. Model inputs were calculated by combining data from representative household surveys on alcohol purchasing and consumption, administrative and healthcare data on 43 alcohol-attributable diseases, and published price elasticities and relative risk functions. Outcomes were annual per capita consumption, consumer spending, and alcohol-related deaths. Uncertainty was assessed via partial probabilistic sensitivity analysis (PSA) and scenario analysis. The pricing strategies differ as to how effects are distributed across the population, and, from a public health perspective, heavy drinkers in routine/manual occupations are a key group as they are at greatest risk of health harm from their drinking. Strength-based taxation and minimum unit pricing would have greater effects on mortality among drinkers in routine/manual occupations (particularly for heavy drinkers, where the estimated policy effects on mortality rates are as follows: current tax increase, −3.2%; value-based tax, −2.9%; strength-based tax, −6.1%; minimum unit pricing, −7.8%) and lesser impacts among drinkers in professional/managerial occupations (for heavy drinkers: current tax increase, −1.3%; value-based tax, −1.4%; strength-based tax, +0.2%; minimum unit pricing, +0.8%). Results from the PSA give slightly greater mean effects for both the routine/manual (current tax increase, −3.6% [95% uncertainty interval (UI) −6.1%, −0.6%]; value-based tax, −3.3% [UI −5.1%, −1.7%]; strength-based tax, −7.5% [UI −13.7%, −3.9%]; minimum unit pricing, −10.3% [UI −10.3%, −7.0%]) and professional/managerial occupation groups (current tax increase, −1.8% [UI −4.7%, +1.6%]; value-based tax, −1.9% [UI −3.6%, +0.4%]; strength-based tax, −0.8% [UI −6.9%, +4.0%]; minimum unit pricing, −0.7% [UI −5.6%, +3.6%]). Impacts of price changes on moderate drinkers were small regardless of income or socioeconomic group. Analysis of uncertainty shows that the relative effectiveness of the four policies is fairly stable, although uncertainty in the absolute scale of effects exists. Volumetric taxation and minimum unit pricing consistently outperform increasing the current tax or adding an ad valorem tax in terms of reducing mortality among the heaviest drinkers and reducing alcohol-related health inequalities (e.g., in the routine/manual occupation group, volumetric taxation reduces deaths more than increasing the current tax in 26 out of 30 probabilistic runs, minimum unit pricing reduces deaths more than volumetric tax in 21 out of 30 runs, and minimum unit pricing reduces deaths more than increasing the current tax in 30 out of 30 runs). Study limitations include reducing model complexity by not considering a largely ineffective ban on below-tax alcohol sales, special duty rates covering only small shares of the market, and the impact of tax fraud or retailer non-compliance with minimum unit prices. Conclusions Our model estimates that, compared to tax increases under the current system or introducing taxation based on product value, alcohol-content-based taxation or minimum unit pricing would lead to larger reductions in health inequalities across income groups. We also estimate that alcohol-content-based taxation and minimum unit pricing would have the largest impact on harmful drinking, with minimal effects on those drinking in moderation. PMID:26905063

Lithospheric strength variations as a control on new plate boundaries: examples from the northern Red Sea region

NASA Astrophysics Data System (ADS)

Steckler, Michael S.; ten Brink, Uri S.

1986-08-01

The complex plate boundary between Arabia and Africa at the northern end of the Red Sea includes the Gulf of Suez rift and the Gulf of Aqaba—Dead Sea transform. Geologic evidence indicates that during the earliest phase of rifting the Red Sea propagated NNW towards the Mediterranean Sea creating the Gulf of Suez. Subsequently, the majority of the relative movement between the plates shifted eastward to the Dead Sea transform. We propose that an increase in the strength of the lithosphere across the Mediterranean continental margin acted as a barrier to the propagation of the rift. A new plate boundary, the Dead Sea transform formed along a zone of minimum strength. We present an analysis of lithospheric strength variations across the Mediterranean continental margin. The main factors controlling these variations are the geotherm, crustal thickness and composition, and sediment thickness. The analysis predicts a characteristic strength profile at continental margins which consists of a marked increase in strength seaward of the hinge zone and a strength minimum landward of the hinge zone. This strength profile also favors the creation of thin continental slivers such as the Levant west of the Dead Sea transform and the continental promontory containing Socotra Island at the mouth of the Gulf of Aden. Calculations of strength variations based on changes of crustal thickness, geotherm and sediment thickness can be extended to other geologic settings as well. They can explain the location of rerifting events at intracratonic basins, of backarc basins and of major continental strike-slip zones.

Synchrotron X-ray Scattering; Sensile Strength and Strain-Induced Crystallization in Carbon Black Filled Natural Rubber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toki,S.; Minouchi, N.; Sics, I.

2008-01-01

The tensile strength of rubber depends on a combination of contributions, in particular on the finite extensibility of chain segments between network points and on strain-induced crystallization. In order to achieve high tensile strength at high strain at break, we optimized the composition and processing parameters to gain high molecular flexibility by the cure conditions, to acquire high flexibility of sulfur bridges by the accelerator, and to increase the modulus level without losing rubber molecule flexibility by carbon black. As a result, our formula performed a tensile strength of 42.5 MPa at 25 C under ISO-37, as officially measured bymore » the Society of Rubber Industry, Japan, in 2004.« less

Tensile Properties of Under-Matched Weld Joints for 950 MPa Steel.

NASA Astrophysics Data System (ADS)

Yamamoto, Kouji; Arakawa, Toshiaki; Akazawa, Nobuki; Yamamoto, Kousei; Matsuo, Hiroki; Nakagara, Kiyoyuki; Suita, Yoshikazu

In welding of 950 MPa-class high tensile strength steel, preheating is crucial in order to avoid cold cracks, which, however, eventually increases welding deformations. One way to decrease welding deformations is lowering preheating temperature by using under-matched weld metal. Toyota and others clarify that although breaking elongation can decrease due to plastic constraint effect under certain conditions, static tensile of under-matched weld joints is comparable to that of base metal. However, there has still been no report about joint static tensile of under-matched weld joints applied to 950 MPa-class high tensile strength steel. In this study, we aim to research tensile strength and fatigue strength of under-matched weld joints applied to 950 MPa-class high tensile steel.

Self-healable electrically conducting wires for wearable microelectronics.

PubMed

Sun, Hao; You, Xiao; Jiang, Yishu; Guan, Guozhen; Fang, Xin; Deng, Jue; Chen, Peining; Luo, Yongfeng; Peng, Huisheng

2014-09-01

Electrically conducting wires play a critical role in the advancement of modern electronics and in particular are an important key to the development of next-generation wearable microelectronics. However, the thin conducting wires can easily break during use, and the whole device fails to function as a result. Herein, a new family of high-performance conducting wires that can self-heal after breaking has been developed by wrapping sheets of aligned carbon nanotubes around polymer fibers. The aligned carbon nanotubes offer an effective strategy for the self-healing of the electric conductivity, whereas the polymer fiber recovers its mechanical strength. A self-healable wire-shaped supercapacitor fabricated from a wire electrode of this type maintained a high capacitance after breaking and self-healing. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mechanical enhancement and in vitro biocompatibility of nanofibrous collagen-chitosan scaffolds for tissue engineering.

PubMed

Zou, Fengjuan; Li, Runrun; Jiang, Jianjun; Mo, Xiumei; Gu, Guofeng; Guo, Zhongwu; Chen, Zonggang

2017-12-01

The collagen-chitosan complex with a three-dimensional nanofiber structure was fabricated to mimic native ECM for tissue repair and biomedical applications. Though the three-dimensional hierarchical fibrous structures of collagen-chitosan composites could provide more adequate stimulus to facilitate cell adhesion, migrate and proliferation, and thus have the potential as tissue engineering scaffolding, there are still limitations in their applications due to the insufficient mechanical properties of natural materials. Because poly (vinyl alcohol) (PVA) and thermoplastic polyurethane (TPU) as biocompatible synthetic polymers can offer excellent mechanical properties, they were introduced into the collagen-chitosan composites to fabricate the mixed collagen/chitosan/PVA fibers and a sandwich structure (collagen/chitosan-TPU-collagen/chitosan) of nanofiber in order to enhance the mechanical properties of the nanofibrous collagen-chitosan scaffold. The results showed that the tensile behavior of materials was enhanced to different degrees with the difference of collagen content in the fibers. Besides the Young's modulus had no obvious changes, both the break strength and the break elongation of materials were heightened after reinforced by PVA. For the collagen-chitosan nanofiber reinforced by TPU, both the break strength and the Young's modulus of materials were heightened in different degrees with the variety of collagen content in the fibers despite the decrease of the break elongation of materials to some extent. In vitro cell test demonstrated that the materials could provide adequate environment for cell adhesion and proliferation. All these indicated that the reinforced collagen-chitosan nanofiber could be as potential scaffold for tissue engineering according to the different mechanical requirements in clinic.

49 CFR 195.112 - New pipe.

Code of Federal Regulations, 2013 CFR

2013-10-01

... with the following: (a) The pipe must be made of steel of the carbon, low alloy-high strength, or alloy... sets forth the chemical requirements for the pipe steel and mechanical tests for the pipe to provide... made, the specified minimum yield strength or grade, and the pipe size. The marking must be applied in...

49 CFR 195.112 - New pipe.

Code of Federal Regulations, 2012 CFR

2012-10-01

... with the following: (a) The pipe must be made of steel of the carbon, low alloy-high strength, or alloy... sets forth the chemical requirements for the pipe steel and mechanical tests for the pipe to provide... made, the specified minimum yield strength or grade, and the pipe size. The marking must be applied in...

49 CFR 195.112 - New pipe.

Code of Federal Regulations, 2014 CFR

2014-10-01

... with the following: (a) The pipe must be made of steel of the carbon, low alloy-high strength, or alloy... sets forth the chemical requirements for the pipe steel and mechanical tests for the pipe to provide... made, the specified minimum yield strength or grade, and the pipe size. The marking must be applied in...

49 CFR 195.112 - New pipe.

Code of Federal Regulations, 2011 CFR

2011-10-01

... with the following: (a) The pipe must be made of steel of the carbon, low alloy-high strength, or alloy... sets forth the chemical requirements for the pipe steel and mechanical tests for the pipe to provide... made, the specified minimum yield strength or grade, and the pipe size. The marking must be applied in...

49 CFR 195.112 - New pipe.

Code of Federal Regulations, 2010 CFR

2010-10-01

... with the following: (a) The pipe must be made of steel of the carbon, low alloy-high strength, or alloy... sets forth the chemical requirements for the pipe steel and mechanical tests for the pipe to provide... made, the specified minimum yield strength or grade, and the pipe size. The marking must be applied in...

Relationship of magnetic field strength and brightness of fine-structure elements in the solar temperature minimum region

NASA Technical Reports Server (NTRS)

Cook, J. W.; Ewing, J. A.

1990-01-01

A quantitative relationship was determined between magnetic field strength (or magnetic flux) from photospheric magnetograph observations and the brightness temperature of solar fine-structure elements observed at 1600 A, where the predominant flux source is continuum emission from the solar temperature minimum region. A Kitt Peak magnetogram and spectroheliograph observations at 1600 A taken during a sounding rocket flight of the High Resolution Telescope and Spectrograph from December 11, 1987 were used. The statistical distributions of brightness temperature in the quiet sun at 1600 A, and absolute value of magnetic field strength in the same area were determined from these observations. Using a technique which obtains the best-fit relationship of a given functional form between these two histogram distributions, a quantitative relationship was determined between absolute value of magnetic field strength B and brightness temperature which is essentially linear from 10 to 150 G. An interpretation is suggested, in which a basal heating occurs generally, while brighter elements are produced in magnetic regions with temperature enhancements proportional to B.

Mechanical tensile testing of titanium 15-3-3-3 and Kevlar 49 at cryogenic temperatures

NASA Astrophysics Data System (ADS)

James, B. L.; Martinez, R. M.; Shirron, P.; Tuttle, J.; Galassi, N. M.; McGuinness, D. S.; Puckett, D.; Francis, J. J.; Flom, Y.

2012-06-01

Titanium 15-3-3-3 and Kevlar 49 are highly desired materials for structural components in cryogenic applications due to their low thermal conductivity at low temperatures. Previous tests have indicated that titanium 15-3-3-3 becomes increasingly brittle as the temperature decreases. Furthermore, little is known regarding the mechanical properties of Kevlar 49 at low temperatures, most specifically its Young's modulus. This testing investigates the mechanical properties of both materials at cryogenic temperatures through cryogenic mechanical tensile testing to failure. The elongation, ultimate tensile strength, yield strength, and break strength of both materials are provided and analyzed here.

Mechanical Tensile Testing of Titanium 15-3-3-3 and Kevlar 49 at Cryogenic Temperatures

NASA Technical Reports Server (NTRS)

James, Bryan L.; Martinez, Raul M.; Shirron, Peter; Tuttle, Jim; Galassi, Nicholas M.; Mcguinness, Daniel S.; Puckett, David; Francis, John J.; Flom, Yury

2011-01-01

Titanium 15-3-3-3 and Kevlar 49 are highly desired materials for structural components in cryogenic applications due to their low thennal conductivity at low temperatures. Previous tests have indicated that titanium 15-3-3-3 becomes increasingly brittle as the temperature decreases. Furthermore, little is known regarding the mechanical properties of Kevlar 49 at low temperatures, most specifically its Young's modulus. This testing investigates the mechanical properties of both materials at cryogenic temperatures through cryogenic mechanical tensile testing to failure. The elongation, ultimate tensile strength, yield strength, and break strength of both materials are provided and analyzed here.

Large-wave simulation of spilling breaking and undertow current over constant slope beach

NASA Astrophysics Data System (ADS)

Dimas, Athanassios; Kolokythas, Gerasimos; Dimakopoulos, Aggelos

2011-11-01

The three-dimensional, free-surface flow, developing by the propagation of nonlinear breaking waves over a constant slope bed, is numerically simulated. The main objective is to investigate the effect of spilling breaking on the characteristics of the induced undertow current by performing large-wave simulations (LWS) based on the numerical solution of the Navier-Stokes equations subject to the fully nonlinear free-surface boundary conditions and the appropriate bottom, inflow and outflow boundary conditions. The equations are properly transformed so that the computational domain becomes time-independent. In the present study, the case of incoming waves with wavelength to inflow depth ratio λ/ d ~ 6.6 and wave steepness H/ λ ~0.025, over bed of slope tan β = 1/35, is investigated. The LWS predicts satisfactorily breaking parameters - height and depth - and wave dissipation in the surf zone, in comparison to experimental data. In the corresponding LES, breaking height and depth are smaller and wave dissipation in the surf zone is weaker. For the undertow current, it is found that it is induced by the breaking process at the free surface, while its strength is controlled by the bed shear stress. Finally, the amplitude of the bed shear stress increases substantially in the breaking zone, becoming up to six times larger than the respective amplitude at the outer region.

Proceedings of the Annual Mechanics of Composites Review (8th) Held at Wright-Patterson AFB, Ohio on 5-7 October 1982.

DTIC Science & Technology

1983-04-01

Spectrum Fatigue Behavior of Postbuckled Shear Panels; PO01 246 Development of Analysis for Predicting Compression Fatigt Life and Residual Strength in...Lazyup and Frequency Effects on Fatigue Life of Composites, POOl 256 Effect of Stress Ratio on Fatigue Life of Composites,’ POOl 257 High-Load Transfer...L. Agerwall, Northrop Corporation 0950-1020 BREAK 1020-1100 DEVELOPMENT OF ANALYSIS FOR PREDICTING COMPRESSION 34 FATIGUE LIFE AND RESIDUAL STRENGTH

Relationship between Age and the Ability to Break Scored Tablets

PubMed Central

Notenboom, Kim; Vromans, Herman; Schipper, Maarten; Leufkens, Hubert G. M.; Bouvy, Marcel L.

2016-01-01

Background: Practical problems with the use of medicines, such as difficulties with breaking tablets, are an often overlooked cause for non-adherence. Tablets frequently break in uneven parts and loss of product can occur due to crumbling and powdering. Health characteristics, such as the presence of peripheral neuropathy, decreased grip strength and manual dexterity, can affect a patient's ability to break tablets. As these impairments are associated with aging and age-related diseases, such as Parkinson's disease and arthritis, difficulties with breaking tablets could be more prevalent among older adults. The objective of this study was to investigate the relationship between age and the ability to break scored tablets. Methods: A comparative study design was chosen. Thirty-six older adults and 36 young adults were systematically observed with breaking scored tablets. Twelve different tablets were included. All participants were asked to break each tablet by three techniques: in between the fingers with the use of nails, in between the fingers without the use of nails and pushing the tablet downward with one finger on a solid surface. It was established whether a tablet was broken or not, and if broken, whether the tablet was broken accurately or not. Results: The older adults experienced more difficulties to break tablets compared to the young adults. On average, the older persons broke 38.1% of the tablets, of which 71.0% was broken accurately. The young adults broke 78.2% of the tablets, of which 77.4% was broken accurately. Further analysis by mixed effects logistic regression revealed that age was associated with the ability to break tablets, but not with the accuracy of breaking. Conclusions: Breaking scored tablets by hand is less successful in an elderly population compared to a group of young adults. Health care providers should be aware that tablet breaking is not appropriate for all patients and for all drugs. In case tablet breaking is unavoidable, a patient's ability to break tablets should be assessed by health care providers and instructions on the appropriate method of breaking should be provided. PMID:27507946

Landau level splitting in Cd3As2 under high magnetic fields

NASA Astrophysics Data System (ADS)

Cao, Junzhi; Liang, Sihang; Zhang, Cheng; Liu, Yanwen; Huang, Junwei; Jin, Zhao; Chen, Zhi-Gang; Wang, Zhijun; Wang, Qisi; Zhao, Jun; Li, Shiyan; Dai, Xi; Zou, Jin; Xia, Zhengcai; Li, Liang; Xiu, Faxian

2015-07-01

Three-dimensional topological Dirac semimetals (TDSs) are a new kind of Dirac materials that exhibit linear energy dispersion in the bulk and can be viewed as three-dimensional graphene. It has been proposed that TDSs can be driven to other exotic phases like Weyl semimetals, topological insulators and topological superconductors by breaking certain symmetries. Here we report the first transport experiment on Landau level splitting in TDS Cd3As2 single crystals under high magnetic fields, suggesting the removal of spin degeneracy by breaking time reversal symmetry. The detected Berry phase develops an evident angular dependence and possesses a crossover from non-trivial to trivial state under high magnetic fields, a strong hint for a fierce competition between the orbit-coupled field strength and the field-generated mass term. Our results unveil the important role of symmetry breaking in TDSs and further demonstrate a feasible path to generate a Weyl semimetal phase by breaking time reversal symmetry.

Landau level splitting in Cd3As2 under high magnetic fields.

PubMed

Cao, Junzhi; Liang, Sihang; Zhang, Cheng; Liu, Yanwen; Huang, Junwei; Jin, Zhao; Chen, Zhi-Gang; Wang, Zhijun; Wang, Qisi; Zhao, Jun; Li, Shiyan; Dai, Xi; Zou, Jin; Xia, Zhengcai; Li, Liang; Xiu, Faxian

2015-07-13

Three-dimensional topological Dirac semimetals (TDSs) are a new kind of Dirac materials that exhibit linear energy dispersion in the bulk and can be viewed as three-dimensional graphene. It has been proposed that TDSs can be driven to other exotic phases like Weyl semimetals, topological insulators and topological superconductors by breaking certain symmetries. Here we report the first transport experiment on Landau level splitting in TDS Cd3As2 single crystals under high magnetic fields, suggesting the removal of spin degeneracy by breaking time reversal symmetry. The detected Berry phase develops an evident angular dependence and possesses a crossover from non-trivial to trivial state under high magnetic fields, a strong hint for a fierce competition between the orbit-coupled field strength and the field-generated mass term. Our results unveil the important role of symmetry breaking in TDSs and further demonstrate a feasible path to generate a Weyl semimetal phase by breaking time reversal symmetry.

Landau level splitting in Cd3As2 under high magnetic fields

PubMed Central

Cao, Junzhi; Liang, Sihang; Zhang, Cheng; Liu, Yanwen; Huang, Junwei; Jin, Zhao; Chen, Zhi-Gang; Wang, Zhijun; Wang, Qisi; Zhao, Jun; Li, Shiyan; Dai, Xi; Zou, Jin; Xia, Zhengcai; Li, Liang; Xiu, Faxian

2015-01-01

Three-dimensional topological Dirac semimetals (TDSs) are a new kind of Dirac materials that exhibit linear energy dispersion in the bulk and can be viewed as three-dimensional graphene. It has been proposed that TDSs can be driven to other exotic phases like Weyl semimetals, topological insulators and topological superconductors by breaking certain symmetries. Here we report the first transport experiment on Landau level splitting in TDS Cd3As2 single crystals under high magnetic fields, suggesting the removal of spin degeneracy by breaking time reversal symmetry. The detected Berry phase develops an evident angular dependence and possesses a crossover from non-trivial to trivial state under high magnetic fields, a strong hint for a fierce competition between the orbit-coupled field strength and the field-generated mass term. Our results unveil the important role of symmetry breaking in TDSs and further demonstrate a feasible path to generate a Weyl semimetal phase by breaking time reversal symmetry. PMID:26165390

Stimulation of wound healing by positively charged dextran beads depends upon clustering of beads and cells in close proximity to the wound.

PubMed

Tawil, N J; Connors, D; Gies, D; Bennett, S; Gruskin, E; Mustoe, T

1999-01-01

We have previously shown that positively charged dextran (DEAE A25) increases wound breaking strength in linear incisions in rats and nonhuman primates at days 10-14 postwounding. In this article, we examined the cellular responses to different types of charged dextran beads (DEAE A50 and Cytodex-1) in culture studies and in rat incisional wounds. We show that Cytodex 1 and DEAE A50 beads also increased wound breaking strength in a rat linear incisional model. However, the increase was approximately 30-40% less than that observed in wounds treated with DEAE A25 beads. The main distinction between the three types of beads was the presence of bead clusters observed in tissue sections. Wounds treated with DEAE A25 beads formed distinct clusters while both Cytodex 1 and DEAE A50 beads clustered to a lesser extent or failed to cluster at all. We propose that the different types of charged dextran beads improve healing by promoting cell adhesion and encouraging proliferation in close proximity to the wound. We also hypothesize that the 30-40% improvement in wound breaking strength seen with DEAE A25 beads compared to other types of charged dextran beads (DEAE A50 and Cytodex-1) originates from the unique characteristic of DEAE A25 beads in forming cell-bead aggregates adjacent to the wounded area. This clustering, in turn, affects the distribution of cells infiltrating the wounded area (such as macrophages) during the healing process and, as a consequence, alters the distribution of matrix molecules and growth factors secreted by these cells.

Investigation into the optimal prosthetic material for wound healing of abdominal wall defects

PubMed Central

Akcakaya, Adem; Aydogdu, Ibrahim; Citgez, Bulent

2018-01-01

The purpose of this experimental study is to investigate and compare the effects of prosthetic materials used for wound healing of abdominal wall hernias. A total of 60 rats were divided into five equal groups: Group I, control subjected to laparotomy; group II, abdominal wall defect 3×2 cm+polypropylene (PP) mesh; group III, abdominal wall defect 3×2 cm+PP mesh+hyaluronate and carboxymethylcellulose (H-CMC; Seprafilm®); group IV, abdominal wall defect 3×2 cm+polytetrafluoroethylene (PTFE; Composix™); and group V, abdominal wall defect 3×2 cm+polyethylene terephthalate (PET; Dacron®). A total of 14 days after the surgery, rats were sacrificed and the meshes with the surrounding tissue were extracted in block. The breaking strength of the mesh from the fascia was recorded. The healing tissue was examined with the index of histopathology and the hydroxyproline value was analyzed using the Switzer method. Both the breaking strength and histopathological index of the wound healing were significantly improved in groups II and III compared with that in groups IV and V (P<0.001). Hydroxyproline values were the highest in group I (P<0.001). There was also a statistically significant difference between groups II and IV, and group V and the other groups (P<0.001). The present findings demonstrated that PP mesh and PP mesh+H-CMC had a superior breaking strength and improved histopathologic indices compared with PTFE and PET. Furthermore, hydroxyproline values were the lowest in the PET group. In conclusion, wound healing was improved in the PP mesh group and the PP mesh+H-CMC group compared with the PTFE and PET groups according to the present study parameters. PMID:29399133

[Cereal bars with soy protein and wheat germ, physicochemical characteristics and texture during the storage].

PubMed

Castro Freitas, Daniela D G

2005-09-01

Studies analyzing cereal bars have reported on consumer characteristics and preferences in sensory analyses and on their market growth, however little has been published on their physicochemical data and texture properties. Thus the objective of this research was to provide information about the storage of a cereal bar formulation with high protein and vitamin levels based on soy protein and wheat germ, packaged in 3 different films (A: PET/PEBD; B: PETmet/PEBD; C: PET/PEBD/AL/PEBD), during 6 months under environmental conditions of temperature (25 +/- 2 degrees C) and relative humidity (56%). The moisture content, water activity, pH and total acidity of the cereal bars were determined. The textural measurements accompanied during storage were breaking strength, hardness and cohesiveness. The cereal bars presented variations in water activity (Aw), moisture content and total acidity during storage. The moisture content of the bars tended to increase, which led to a significant (p = 0.05) influence on the texture characteristics of breaking strength and hardness, in the different packaging films tested. The increase in the values for breaking strength (A: 4756,5N; B: 5093,0N; C: 5575,6N) at 45 days of storage was attributed to a possible crystallization of the agglutinating syrup used for the bars. The textured soy protein used in the formulation could also have contributed to this fact due to its hygroscopic character, also interfering in the decrease in the cohesiveness measurements (deformation) with time. The effect of the different barrier properties of the packaging films tested was significant (p < 0.05) in the stability of the cereal bars during storage.

49 CFR 571.139 - Standard No. 139; New pneumatic radial tires for light vehicles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... breaking away of pieces of the tread or sidewall. Cord means the strands forming the plies in the tire... with a 12-inch or smaller rim diameter, each tire shall have not less than six treadwear indicators... mountain, there must be a six-sided snowflake having a minimum height of one-half the tallest peak...

Retinal detachment in pseudophakia.

PubMed

Galin, M A; Poole, T A; Obstbaum, S A

1979-07-01

In a series of cataract patients excluding myopic individuals, under age 60 years, and cases in which vitreous loss occurred, retinal detachment was no less frequent after intracapsular cataract extraction and Sputnik iris supported lenses than in controls. Both groups were followed up for a minimum of two years. The detachments predominantly occurred from retinal breaks in areas of the retina that looked normal preoperatively.

Bonding strength of alkyl-2-cyanoacrylates to bone in vitro.

PubMed

Kilpikari, J; Lapinsuo, M; Törmälä, P; Pätiälä, H; Rokkanen, P

1986-10-01

This study measured the bonding strength between alkyl-2-cyanoacrylates and bone, and examined how treatment of the bone surface with acid, and prolonged exposure to moisture, affected this strength. The initial strength of all cyanoacrylates was high (9.6-11.2 N/mm2). In long-term experiments under water, n- and i-butylcyanoacrylates lost their strength at a far slower rate than ethylcyanoacrylates. However, the butylcyanoacrylates also showed a decrease of 15% in strength after three weeks. Pretreatment of the bone surface with acid did not have a marked effect on bonding strength, although SEM investigation revealed that the acid treatment had increased the porosity of the bone surface. A study of the fracture surface proved that the adhesive film tended to loosen or break after 3 to 6 weeks under water. The decrease in the bonding strength was probably due to the degradation of the adhesive film in water which loosened mechanical bonds between the bone and adhesive. Considering clinical use it would be necessary to achieve better long-term strength.

Early Treatment in Shock

DTIC Science & Technology

2011-06-01

mem -6 branes releasing RNA into the lysis solution, and shears the genomic DNA decreasing 7 the viscosity of the lysate. Whole blood lysates from...doses, compared with saline controls. The L-arginine groups 3 showed increased OHP and wound breaking strength as compared with both shocked 4 and

Investigation on thermal oxidative aging of nitrile rubber (NBR) O-rings under compression stress

NASA Astrophysics Data System (ADS)

Liu, X. R.; Zhang, W. F.; Lou, W. T.; Huang, Y. X.; Dai, W.

2017-11-01

The degradation behaviors of nitrile rubber O-rings exposure to air under compression were investigated at three elevated temperatures. The physical and mechanical properties of the aging samples before and after exposure at selected time were studied by measuring weight loss, tensile strength and elongation at break. The Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and fracture morphology were used to reveal the microstructural changes of the aging samples. The results indicate that the weight decreased with exposure time and temperature. Based on the results of the crosslinking density, the crosslinking predominates during the most of aging process. The significant changes in tensile strength and elongation at break also indicate the severe degradation in air. The fracture morphology results show that the fracture surface after 64 days of exposure to air turns rough and present defects. The ATR-FTIR results demonstrate that the hydroxyl groups were formed for the samples aged in air.

PP/EPDM-blends by dynamic vulcanization: Influence of increasing peroxide concentration on mechanical, morphological and rheological characteristics

NASA Astrophysics Data System (ADS)

Patermann, S.; Altstädt, V.

2014-05-01

Thermoplastic vulcanizates (TPVs) combine the elastic properties of thermoset cross-linked rubbers with the melt processability of thermoplastics. The most representative examples of this class are the TPVs based on polypropylene (PP) and ethylene-propylenediene terpolymer rubber (EPDM). The PP/EPDM blends were produced by dynamic vulcanization in a continuous extrusion process. The influence of different peroxide concentrations was studied with regard to cross-link density, compression set, tensile strength/elongation at break and morphology. With increasing peroxide concentration, the cross-link density increases, leading to a reduction of the compression set by 50 %. The cross-linked blends show smaller dispersed EPDM particles than the uncured one. With a peroxide concentration between 0.2 and 0.6 % a maximum in tensile strength and elongation at break was found and with increasing peroxide concentration, the complex viscosity of the TPVs decreases. Compared to batch processes, the results show nearly the same trends.

Enhanced physicochemical properties of chitosan/whey protein isolate composite film by sodium laurate-modified TiO2 nanoparticles.

PubMed

Zhang, Wei; Chen, Jiwang; Chen, Yue; Xia, Wenshui; Xiong, Youling L; Wang, Hongxun

2016-03-15

Chitosan/whey protein isolate film incorporated with sodium laurate-modified TiO2 nanoparticles was developed. The nanocomposite film was characterized by scanning electron microscopy, X-ray diffraction and differential scanning calorimetry, and investigated in physicochemical properties as color, tensile strength, elongation at break, water vapor permeability and water adsorption isotherm. Our results showed that the nanoparticles improved the compatibility of whey protein isolate and chitosan. Addition of nanoparticles increased the whiteness of chitosan/whey protein isolate film, but decreased its transparency. Compared with binary film, the tensile strength and elongation at break of nanocomposite film were increased by 11.51% and 12.01%, respectively, and water vapor permeability was decreased by 7.60%. The equilibrium moisture of nanocomposite film was lower than binary film, and its water sorption isotherm of the nanocomposite film fitted well to Guggenheim-Anderson-deBoer model. The findings contributed to the development of novel food packaging materials. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of peppermint and citronella essential oils on properties of fish skin gelatin edible films

NASA Astrophysics Data System (ADS)

Yanwong, S.; Threepopnatkul, P.

2015-07-01

Fish skin gelatin films incorporated with peppermint and citronella essential oils at difference concentrations (10, 20 and 30% w/w) were prepared by solution casting. Addition of peppermint oil contributed to a significant decrease of tensile strength and Young's modulus, while the percent elongation at break showed an obvious increase except at 30% w/w. On the other hand, addition of citronella oils promoted a great increase of tensile strength and young's modulus, but an intense decrease of the percent elongation at break. At the predetermined content, the film incorporated with citronella oils outperformed the one with peppermint oils in term of water vapor transmission and solubility in water. Thermal properties of gelatin films with citronella oils exhibited an enhancement in heat stability, while the one with peppermint oils showed slight decrease in heat stability. The additions with both of essential oils exhibited excellent antibacterial properties against both Staphylococcus aureus and Escherichia coli.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ushizima, Daniela; Perciano, Talita; Krishnan, Harinarayan

Fibers provide exceptional strength-to-weight ratio capabilities when woven into ceramic composites, transforming them into materials with exceptional resistance to high temperature, and high strength combined with improved fracture toughness. Microcracks are inevitable when the material is under strain, which can be imaged using synchrotron X-ray computed micro-tomography (mu-CT) for assessment of material mechanical toughness variation. An important part of this analysis is to recognize fibrillar features. This paper presents algorithms for detecting and quantifying composite cracks and fiber breaks from high-resolution image stacks. First, we propose recognition algorithms to identify the different structures of the composite, including matrix cracks andmore » fibers breaks. Second, we introduce our package F3D for fast filtering of large 3D imagery, implemented in OpenCL to take advantage of graphic cards. Results show that our algorithms automatically identify micro-damage and that the GPU-based implementation introduced here takes minutes, being 17x faster than similar tools on a typical image file.« less

Rheological, physical and sensorial evaluation of cookies supplemented with dairy powders.

PubMed

Sert, Durmuş; Demir, M Kürşat; Ertaş, Nilgün

2016-04-01

The effect of dairy powders (skim milk powder, butter milk powder, sodium caseinate, yoghurt powder, milk powder and colostrum powder) on cookie quality was studied. Cookies were tested for aw, calorimetric energy, diameter, thickness, spread ratio, breaking strength, colour, dough consistency and sensory evaluation. The lowest aw values were obtained for cookies containing colostrum powder; also the highest calorimetric energy values were obtained from the colostrum powder-added cookies. Diameter values of cookies with the addition of skim milk powder, butter milk powder, yoghurt powder and milk powder were higher than that of sodium caseinate and colostrum powder. The lowest spread ratio was measured in the cookie samples with added skim milk powder. The addition of yoghurt powder gave the highest breaking strength of cookies. Cookies with sodium caseinate addition exhibited the highest lightness (L*) values than the other cookies with different dairy powders. Cookies prepared with butter milk powder received the highest scores for colour, appearance, texture, crispness and overall acceptability. © The Author(s) 2015.

A comparative study of gelatin and starch-based nano-composite films modified by nano-cellulose and chitosan for food packaging applications.

PubMed

Noorbakhsh-Soltani, S M; Zerafat, M M; Sabbaghi, S

2018-06-01

Environmental concerns have led to extensive research for replacing polymer-based food packaging with bio-nano-composites. In this study, incorporation of nano-cellulose into gelatin and starch matrices is investigated for this purpose. Chitosan is used to improve mechanical, anti-fungal and waterproof properties. Experiments are designed and analyzed using response surface methodology. Nano-Cellulose is synthesized via acid hydrolysis and incorporated in base matrices through wet processing. Also, tensile strength test, food preservation, transparency in visible and UV and water contact angle are performed on the nano-composite films. DSC/TGA and air permeability tests are also performed on the optimal films. The results show that increasing nano-cellulose composition to 10% leads to increase the tensile strength at break to 8121 MN/m 2 and decrease the elongation at break. Also, increasing chitosan composition from 5% to 30% can enhance food preservation up to 15 days. Copyright © 2018 Elsevier Ltd. All rights reserved.

Preparation and characterization of semi-refined kappa carrageenan-based edible film for nano coating application on minimally processed food

NASA Astrophysics Data System (ADS)

Manuhara, Godras Jati; Praseptiangga, Danar; Muhammad, Dimas Rahadian Aji; Maimuni, Bawani Hindami

2016-02-01

Shorter and easier processing of semi-refined kappa carrageenan extracted from Euchema cottonii red seaweed result in cheaper price of the polysaccharide. In this study, edible film was prepared from the semi-refined carrageenan without any salt addition. The effect of the carrageenan concentration (1.0, 1.5, and 2.0% w/v) on physical and mechanical properties of the edible film was studied. Edible film thickness and tensile strength increased but elongation at break and water vapor transmission rate (WVTR) decreased as the concentration increased. Based on the characteristic of the edible film, formulation using 2% carrageenan was recommended. The edible film demonstrated the characteristic as follow: 0.054 mm thickness, 21.14 MPa tensile strength, 12.36% elongation at break, and 9.56 g/m2.hour WVTR. It was also noted the carrageenan-based edible film indicated potential physical and mechanical characteristics for nano coating applications on minimally processed food.

Quantifying the Impact of Additional Laboratory Tests on the Quality of a Geomechanical Model

NASA Astrophysics Data System (ADS)

Fillion, Marie-Hélène; Hadjigeorgiou, John

2017-05-01

In an open-pit mine operation, the design of safe and economically viable slopes can be significantly influenced by the quality and quantity of collected geomechanical data. In several mining jurisdictions, codes and standards are available for reporting exploration data, but similar codes or guidelines are not formally available or enforced for geotechnical design. Current recommendations suggest a target level of confidence in the rock mass properties used for slope design. As these guidelines are qualitative and somewhat subjective, questions arise regarding the minimum number of tests to perform in order to reach the proposed level of confidence. This paper investigates the impact of defining a priori the required number of laboratory tests to conduct on rock core samples based on the geomechanical database of an operating open-pit mine in South Africa. In this review, to illustrate the process, the focus is on uniaxial compressive strength properties. Available strength data for 2 project stages were analysed using the small-sampling theory and the confidence interval approach. The results showed that the number of specimens was too low to obtain a reliable strength value for some geotechnical domains even if more specimens than the minimum proposed by the ISRM suggested methods were tested. Furthermore, the testing sequence used has an impact on the minimum number of specimens required. Current best practice cannot capture all possibilities regarding the geomechanical property distributions, and there is a demonstrated need for a method to determine the minimum number of specimens required while minimising the influence of the testing sequence.

Aerogel Projects Ongoing in MSFC's Engineering Directorate

NASA Technical Reports Server (NTRS)

Shular, D. A.; Smithers, G. A.; Plawsky, J. L.

2001-01-01

When we speak of an aerogel material, we are referring more to process and structure than to a specific substance. Aerogel, considered the lightest solid material, has been made from silica for seventy years. Resorcinol-formaldehyde, organic aerogels have been developed more recently. However, aerogel can be made from almost any type of substance, even lead. Because an aerogel is mostly air (about 99%), the solid substance used will affect the weight very little. The problem with aerogels is their low tensile strength and lack of elasticity. Therefore, the challenge is to find ways to make the stronger or ways to circumvent the strength issue. Organic aerogels have slightly higher strength than base silica aerogels, while the carbonized version has three to five times the break strength of the base aerogel.

Torsional Rigidity of Single Actin Filaments and Actin-Actin Bond Breaking Force under Torsion Measured Directly by in vitro Micromanipulation

NASA Astrophysics Data System (ADS)

Tsuda, Yuri; Yasutake, Hironori; Ishijima, Akihiko; Yanagida, Toshio

1996-11-01

Knowledge of the elastic properties of actin filaments is crucial for considering its role in muscle contraction, cellular motile events, and formation of cell shape. The stiffness of actin filaments in the directions of stretching and bending has been determined. In this study, we have directly determined the torsional rigidity and breaking force of single actin filaments by measuring the rotational Brownian motion and tensile strength using optical tweezers and microneedles, respectively. Rotational angular fluctuations of filaments supplied the torsional rigidity as (8.0 ± 1.2) × 10-26 Nm2. This value is similar to that deduced from the longitudinal rigidity, assuming the actin filament to be a homogeneous rod. The breaking force of the actin-actin bond was measured while twisting a filament through various angles using microneedles. The breaking force decreased greatly under twist, e.g., from 600-320 pN when filaments were turned through 90 degrees, independent of the rotational direction. Our results indicate that an actin filament exhibits comparable flexibility in the rotational and longitudinal directions, but breaks more easily under torsional load.

Single particles accelerate final stages of capillary break-up

NASA Astrophysics Data System (ADS)

Lindner, Anke; Fiscina, Jorge Eduardo; Wagner, Christian

2015-06-01

Droplet formation of suspensions is present in many industrial and technological processes such as coating and food engineering. Whilst the finite-time singularity of the minimum neck diameter in capillary break-up of simple liquids can be described by well-known self-similarity solutions, the pinching of non-Brownian suspension depends in a complex way on the particle dynamics in the thinning thread. Here we focus on the very dilute regime where the filament contains only isolated beads to identify the physical mechanisms leading to the pronounced acceleration of the filament thinning observed. This accelerated regime is characterized by an asymmetric shape of the filament with an enhanced curvature that depends on the size and the spatial distribution of the particles within the capillary thread.

Scalable Indoor Localization via Mobile Crowdsourcing and Gaussian Process

PubMed Central

Chang, Qiang; Li, Qun; Shi, Zesen; Chen, Wei; Wang, Weiping

2016-01-01

Indoor localization using Received Signal Strength Indication (RSSI) fingerprinting has been extensively studied for decades. The positioning accuracy is highly dependent on the density of the signal database. In areas without calibration data, however, this algorithm breaks down. Building and updating a dense signal database is labor intensive, expensive, and even impossible in some areas. Researchers are continually searching for better algorithms to create and update dense databases more efficiently. In this paper, we propose a scalable indoor positioning algorithm that works both in surveyed and unsurveyed areas. We first propose Minimum Inverse Distance (MID) algorithm to build a virtual database with uniformly distributed virtual Reference Points (RP). The area covered by the virtual RPs can be larger than the surveyed area. A Local Gaussian Process (LGP) is then applied to estimate the virtual RPs’ RSSI values based on the crowdsourced training data. Finally, we improve the Bayesian algorithm to estimate the user’s location using the virtual database. All the parameters are optimized by simulations, and the new algorithm is tested on real-case scenarios. The results show that the new algorithm improves the accuracy by 25.5% in the surveyed area, with an average positioning error below 2.2 m for 80% of the cases. Moreover, the proposed algorithm can localize the users in the neighboring unsurveyed area. PMID:26999139

Attributing Historical Changes in Probabilities of Record-Breaking Daily Temperature and Precipitation Extreme Events

DOE PAGES

Shiogama, Hideo; Imada, Yukiko; Mori, Masato; ...

2016-08-07

Here, we describe two unprecedented large (100-member), longterm (61-year) ensembles based on MRI-AGCM3.2, which were driven by historical and non-warming climate forcing. These ensembles comprise the "Database for Policy Decision making for Future climate change (d4PDF)". We compare these ensembles to large ensembles based on another climate model, as well as to observed data, to investigate the influence of anthropogenic activities on historical changes in the numbers of record-breaking events, including: the annual coldest daily minimum temperature (TNn), the annual warmest daily maximum temperature (TXx) and the annual most intense daily precipitation event (Rx1day). These two climate model ensembles indicatemore » that human activity has already had statistically significant impacts on the number of record-breaking extreme events worldwide mainly in the Northern Hemisphere land. Specifically, human activities have altered the likelihood that a wider area globally would suffer record-breaking TNn, TXx and Rx1day events than that observed over the 2001- 2010 period by a factor of at least 0.6, 5.4 and 1.3, respectively. However, we also find that the estimated spatial patterns and amplitudes of anthropogenic impacts on the probabilities of record-breaking events are sensitive to the climate model and/or natural-world boundary conditions used in the attribution studies.« less

Preparation and Testing of Plant Seed Meal-based Wood Adhesives

PubMed Central

He, Zhongqi; Chapital, Dorselyn C.

2015-01-01

Recently, the interest in plant seed meal-based products as wood adhesives has steadily increased, as these plant raw materials are considered renewable and environment-friendly. These natural products may serve as alternatives to petroleum-based adhesives to ease environmental and sustainability concerns. This work demonstrates the preparation and testing of the plant seed-based wood adhesives using cottonseed and soy meal as raw materials. In addition to untreated meals, water washed meals and protein isolates are prepared and tested. Adhesive slurries are prepared by mixing a freeze-dried meal product with deionized water (3:25 w/w) for 2 hr. Each adhesive preparation is applied to one end of 2 wood veneer strips using a brush. The tacky adhesive coated areas of the wood veneer strips are lapped and glued by hot-pressing. Adhesive strength is reported as the shear strength of the bonded wood specimen at break. Water resistance of the adhesives is measured by the change in shear strength of the bonded wood specimens at break after water soaking. This protocol allows one to assess plant seed-based agricultural products as suitable candidates for substitution of synthetic-based wood adhesives. Adjustments to the adhesive formulation with or without additives and bonding conditions could optimize their adhesive properties for various practical applications. PMID:25867092

Preparation and testing of plant seed meal-based wood adhesives.

PubMed

He, Zhongqi; Chapital, Dorselyn C

2015-03-05

Recently, the interest in plant seed meal-based products as wood adhesives has steadily increased, as these plant raw materials are considered renewable and environment-friendly. These natural products may serve as alternatives to petroleum-based adhesives to ease environmental and sustainability concerns. This work demonstrates the preparation and testing of the plant seed-based wood adhesives using cottonseed and soy meal as raw materials. In addition to untreated meals, water washed meals and protein isolates are prepared and tested. Adhesive slurries are prepared by mixing a freeze-dried meal product with deionized water (3:25 w/w) for 2 hr. Each adhesive preparation is applied to one end of 2 wood veneer strips using a brush. The tacky adhesive coated areas of the wood veneer strips are lapped and glued by hot-pressing. Adhesive strength is reported as the shear strength of the bonded wood specimen at break. Water resistance of the adhesives is measured by the change in shear strength of the bonded wood specimens at break after water soaking. This protocol allows one to assess plant seed-based agricultural products as suitable candidates for substitution of synthetic-based wood adhesives. Adjustments to the adhesive formulation with or without additives and bonding conditions could optimize their adhesive properties for various practical applications.

Effect of human urine on the tensile strength of sutures used for hypospadias surgery.

PubMed

Kerstein, Ryan L; Sedaghati, Tina; Seifalian, Alexander M; Kang, Norbert

2013-06-01

Hypospadias is the most common congenital condition affecting between 1 in 250 and 300 live births. Even in experienced hands, surgery to repair this congenital defect can have a high complication rate. Wound dehiscence is reported to occur in 5% and fistula formation in 6%-40% depending on technique. The choice of suture material has been shown to affect the complication rate although there is (currently) no consensus about the best suture material to use. Ideally, the sutures used for urethroplasty should be absorbable while maintaining sufficient mechanical strength to support the wounds until they are self-supporting and able to resist urinary flow. Previous studies have compared the effects of human urine on different suture materials especially catgut. However, catgut is now banned in Europe. Our study examined the tensile and breaking strength as well as rate of degradation for four types of absorbable suture now commonly used for hypospadias repairs in the UK. We examined the effect of prolonged storage (up to 27 days) in human urine on 6/0 gauge Vicryl, Vicryl Rapide, Monocryl and polydioxanone (PDS) sutures. These four suture materials are commonly used by the senior plastic consultant surgeon (NK) for hypospadias repairs. 50 mm sections of these suture materials were stored in either urine or saline as control. At specified time points, each suture was placed in a uniaxial load testing machine to assess the stress-strain profile and the mechanical load required to break the suture was measured. Exposure to urine reduced the tensile and breaking strength of all the suture materials tested. PDS demonstrated the greatest resilience. Vicryl Rapide was the weakest suture and degraded completely by day 6. Vicryl and Monocryl had similar degradation profiles, but Vicryl retained more of its tensile strength for longer. There is a balance to be struck between the duration that a suture material must remain in any surgical wound and the risk that it causes foreign body effects. The results of this study suggest that Vicryl has the best characteristics for urethroplasty of the four suture materials tested. Copyright © 2013 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

Effect of electroacupuncture stimulation on long-term recovery following Achilles tendon rupture in a rat model.

PubMed

Imaeda, Miwa; Hojo, Tatsuya; Kitakoji, Hiroshi; Tanaka, Kazuto; Itoi, Megumi; Inoue, Motohiro

2018-04-19

In this study we examined the effect of electroacupuncture (EA) stimulation on the mechanical strength of the rat Achilles tendon after long-term recovery. Using 20 rats, an Achilles tendon rupture model was created in an invasive manner. The rats were assigned to one of three groups, that received EA treatment (EA group), minimal acupuncture (MA group) or remained untreated (Control group). In the EA group, EA stimulation (5 ms, 50 Hz, 20 µA, 20 min) was applied to the rupture region over a period of 90 days (five times/week). In the MA group, needles were inserted into the same positions as in the EA group but no electrical current was applied. After 90 days the tendon was measured to calculate the cross-sectional area of the rupture region. Then, the mechanical strength of the tendon was measured by tensile testing. No significant differences were observed between the three groups in cross-sectional area of the injured tendon. For maximum breaking strength, the EA group showed a significantly higher threshold compared with the Control group (P<0.05) but not the MA group (P=0.24). No significant difference was seen between the MA group and the Control group (P=0.96). Given the EA group showed a significant increase in maximum breaking strength, it is likely that EA stimulation increases the mechanical strength of a repaired tendon after long-term recovery, and EA stimulation could be useful for preventing re-rupture. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Mechanical & morphological properties of attapulgite/NR composites: Effect of mixing time variation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nor, Nor Aina Mohd, E-mail: ayena90@yahoo.com; Othman, Nadras, E-mail: srnadras@usm.my; Ismail, Hanafi, E-mail: ihanafi@usm.my

2015-07-22

The development of composite material based on attapulgite clay (ATP) as a filler and natural rubber (NR) matrices were prepared by combination of melt mixing and latex compounding methods. Sonication technique was chosen in this work to disperse the attapulgite suspension. 6 phr of attapulgite loading was fabricated using different time of mixing ranging from 30 minutes until 2 hours and sonication time was kept constant at 15 minutes. Then, co-coagulating HA latex with attapulgite clay suspension through latex compounding method produced the masterbatch. The masterbatch was compounded with natural rubber by melt mixing method. The mechanical and morphological characteristicsmore » were investigated in this work. From mechanical testing, M1 showed the highest value of tensile and tear strength. By comparing with M30 and M2, M1 shows high 300% tensile modulus and lower crosslink density. However, when the time of mixing was prolonged to 2 hours, the results for tensile strength, elongation at break and tear strength were decreased. This is due to flocculation of attapulgite particles. Sonication techniques also proved that the tensile strength and elongation at break of these three samples were higher compared to gum NR (NR) and attapulgite compounded with NR using a conventional method (in-situ 6). From field emission scanning electron microscope (FESEM) results, it revealed that M1 had good dispersion in the NR system. It is proved that the higher tensile strength was due to good dispersion of attapulgite clay in the NR matrix. It was also supported from crosslink density, which is lower than NR and in-situ 6 results. It showed that the penetration of toluene solvent into rubber compound was restricted. The optimum time, M1 give the best results, which can be compared to control the sample.« less

Cognitive Load Theory and the Use of Worked Examples as an Instructional Strategy in Physics for Distance Learners: A Preliminary Study

ERIC Educational Resources Information Center

Saw, Kim Guan

2017-01-01

This article revisits the cognitive load theory to explore the use of worked examples to teach a selected topic in a higher level undergraduate physics course for distance learners at the School of Distance Education, Universiti Sains Malaysia. With a break of several years from receiving formal education and having only minimum science…

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2012 CFR

2012-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

Mechanical Strength and Broadband Transparency Improvement of Glass Wafers via Surface Nanostructures.

PubMed

Kumar, Amarendra; Kashyap, Kunal; Hou, Max T; Yeh, J Andrew

2016-06-17

In this study, we mechanically strengthened a borosilicate glass wafer by doubling its bending strength and simultaneously enhancing its transparency using surface nanostructures for different applications including sensors, displays and panels. A fabrication method that combines dry and wet etching is used for surface nanostructure fabrication. Specifically, we improved the bending strength of plain borosilicate glass by 96% using these surface nanostructures on both sides. Besides bending strength improvement, a limited optical transmittance enhancement of 3% was also observed in the visible light wavelength region (400-800 nm). Both strength and transparency were improved by using surface nanostructures of 500 nm depth on both sides of the borosilicate glass without affecting its bulk properties or the glass manufacturing process. Moreover, we observed comparatively smaller fragments during the breaking of the nanostructured glass, which is indicative of strengthening. The range for the nanostructure depth is defined for different applications with which improvements of the strength and transparency of borosilicate glass substrate are obtained.

Mechanical Strength and Broadband Transparency Improvement of Glass Wafers via Surface Nanostructures

PubMed Central

Kumar, Amarendra; Kashyap, Kunal; Hou, Max T.; Yeh, J. Andrew

2016-01-01

In this study, we mechanically strengthened a borosilicate glass wafer by doubling its bending strength and simultaneously enhancing its transparency using surface nanostructures for different applications including sensors, displays and panels. A fabrication method that combines dry and wet etching is used for surface nanostructure fabrication. Specifically, we improved the bending strength of plain borosilicate glass by 96% using these surface nanostructures on both sides. Besides bending strength improvement, a limited optical transmittance enhancement of 3% was also observed in the visible light wavelength region (400–800 nm). Both strength and transparency were improved by using surface nanostructures of 500 nm depth on both sides of the borosilicate glass without affecting its bulk properties or the glass manufacturing process. Moreover, we observed comparatively smaller fragments during the breaking of the nanostructured glass, which is indicative of strengthening. The range for the nanostructure depth is defined for different applications with which improvements of the strength and transparency of borosilicate glass substrate are obtained. PMID:27322276

Bending strength of shallow glued-laminated beams of a uniform grade

Treesearch

Catherine M. Marx; Russell C. Moody

1981-01-01

Ninety glued-laminated Douglas-fir or southern pine beams of a uniform grade with 2-, 4-, or 6-laminations were evaluated in static bending tests. No specially graded tension laminations or end joints were used. The purpose of the tests was to determine which of three present design criteria best predict near minimum bending strength values for shallow glued-laminated...

Advances in Low Carbon, High Strength Ferrous Alloys

DTIC Science & Technology

1993-04-01

35 TABLES 1. Specified chemical compositions and mechanical properties for GMAW/SAW/ GTAW wire electrodes, MIL-XXXS type, for welding...minimum service temperature of +300 F. The chromium and molybdenum additions improved hardenability and promoted the formation of mar- tensite in thick...alloying ele- ments ( chromium , nickel and molybdenum) are required, especially for thick sections. Production of high strength steel plate for military

Connecting with the Big Picture

ERIC Educational Resources Information Center

Brophy, Jere

2009-01-01

This article concludes the special issue on identity and motivation by discussing the five preceding contributions. It identifies strengths and limitations in each article and places them within a larger context, indicating ways that the authors could broaden the scope of their inquiries by breaking free of existing limitations or adding…

Asbestos and Asbestosis. LC Science Tracer Bullet.

ERIC Educational Resources Information Center

Alderson, Karen L., Comp.

Asbestos is a naturally occurring mineral found in several forms and because of its temperature-resisting properties, flexibility, and strength, it was widely used in the construction industry, automobile industry, and textile industry. Asbestos becomes dangerous when it crumbles and breaks releasing fibers that can cause asbestosis and certain…

Reading Professionals: The Vital Link.

ERIC Educational Resources Information Center

Gabler, Carol L.

The Family Literacy Program in Eau Claire, Wisconsin is an example of a strong linkage between professional educators, volunteers, and parents. The program uses the strengths of reading professionals working with preschool students and adult learners in order to break the intergenerational cycle of illiteracy. Cooperation and hard work are the…

Thoughts on Designing Things To NOT Break.

ERIC Educational Resources Information Center

Klajnscek, Rich

1998-01-01

Explains aspects of the design and loading of high-ropes courses and other challenge-course equipment. Discusses the engineer's factor of safety, determined by industry standards or the level of risk considered acceptable; definitions of terms for material strength; and the forces involved in loads sustained by belay ropes and cables. (SV)

Recommendations for Implementing an Aquatic Plyometric Program.

ERIC Educational Resources Information Center

Miller, Michael G.; Berry, David C.; Gilders, Roger; Bullard, Sue

2001-01-01

Describes the advantages of using plyometric programs in the water, explaining that they may provide athletes with several benefits (e.g., added resistance, which increases muscle strength, and getting a break from more monotonous drills on land). The paper discusses: the physical properties of water, aquatic rehabilitation that incorporates…

46 CFR 195.35-5 - General.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 1014 (incorporated by reference, see § 195.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire rope shall be either inherently corrosion-resistant, or made so by galvanizing or... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

46 CFR 195.35-5 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 1014 (incorporated by reference, see § 195.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire rope shall be either inherently corrosion-resistant, or made so by galvanizing or... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

46 CFR 195.35-5 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 1014 (incorporated by reference, see § 195.01-3). (d) All lifelines shall be of steel or bronze wire rope. Steel wire rope shall be either inherently corrosion-resistant, or made so by galvanizing or... breaking strength of 1,500 pounds. (e) All equipment shall be maintained in an operative condition, and it...

Safety of working patterns among UK neuroradiologists: what can we learn from the aviation industry and cognitive science?

PubMed

Reicher, John; Currie, Stuart; Birchall, Daniel

2018-04-01

As the volume and complexity of imaging in the UK continues to rise, there is pressure on radiologists to spend increasing lengths of time reporting to cope with the growing workload. However, there is limited guidance for radiologists about structuring the working day to strike the necessary balance between achieving satisfactory reporting volume and maintaining quality and safety. We surveyed 86 neuroradiologists (receiving 59 responses), regarding time spent reporting, frequency and duration of work breaks, and break activities. Our results demonstrate that some neuroradiologists report for up to 12 h a day and for 4 h before taking a break. Mean duration of breaks is less than 15 min and these often consist of computer screen-based or cognitively demanding tasks. Many areas of medicine have looked to the aviation industry to develop improvements in safety through regulated, standardised practices. There are parallels between the work of air traffic controllers (ATCs) and radiologists. We review the legislation that controls the working hours of UK ATCs to minimise fatigue-related errors, and its scientific basis. We also consider the vigilance decrement, a concept in cognitive science which describes the reduction in performance with increasing time-on-task. We conclude that, in comparison with ATCs, work patterns among radiologists are poorly standardised and potentially dangerous. Evidence suggests that placing limits on reporting time and minimum break duration, as well as ensuring appropriate break activities, can benefit reporting quality. It is imperative that radiologists and managers heed these lessons, to improve standards and protect patients from error.

Weldability evaluation of high tensile plates using GMAW process

NASA Astrophysics Data System (ADS)

Datta, R.; Mukerjee, D.; Rohira, K. L.; Veeraraghavan, R.

1999-08-01

High tensile plates, SAILMA-450 high impact (HI) (yield strength, 45 kg/mm2 minimum; ultimate tensile strength, 57 kg/mm2 minimum; elongation, 19% minimum; Charpy impact energy 2.0 kg.m at -20 °C minimum) were successfully developed at the Steel Authority of India Ltd., up to 32 mm plate thickness. Since then the steel has been extensively used for the fabrication of impellers, bridges, excavators, and mining machineries, where welding is an important processing step. The present study deals with the weldability properties of SAILMA-450 HI plates employing the gas metal arc welding process and carbon dioxide gas. Implant and elastic restraint cracking tests were conducted to assess the cold cracking resistance of the weld joint under different welding conditions. The static fatigue limit values were found to be in excess of minimum specified yield strength at higher heat input levels (9.4 and 13.0 kJ/cm), indicating adequate cold cracking resistance. The critical restraint intensities, K cr, were found to vary between 720 and 1280 kg/mm2, indicating that the process can be utilized for fabrication of structures involving moderate to low restraint intensities (200 to 1000 kg/mm2). Lamellar tear tests conducted using full thickness plates at heat input levels ranging from 10 to 27 kJ/cm showed no incidence of lamellar tear upon visual, ultrasonic, and four-section macroexamination. These tests were repeated using machined plates, such that the midthickness of the plates (segregated zone) corresponded to the heat affected zone of the weld. No cracks were observed, indicating good lamellar tear resistance of the weld joint. Optimized welding conditions were formulated based on these tests. The weld joint was subjected to extensive tests to assess the physical properties and soundness of the weld joint. The weld joint exhibited good strength (64.7 kg/mm2) and impact toughness (5.7 and 3.5 kg.m at -20 °C for weld metal and heat affected zone properties. Crack tip opening displacement (CTOD) tests carried out for parent metal, heat-affected zone, and weld metal resulted in δm values of 0.41, 0.40, and 0.34 mm, respectively, which indicates adequate resistance to cleavage fracture. It was concluded that the weld joint conforms to the requirements of SAILMA-450 HI specification and ensures a high integrity of the fabricated products.

Comparative studies on the mechanical properties of natural rubber and natural rubber filled with multi-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Ismail, R.; Ibrahim, A.; Rusop, M.; Adnan, A.

2018-05-01

The present article compares the mechanical properties of natural rubber (NR) and carbon nanotubes (CNTs) filled natural rubber composites. Four types of nanocomposite specimens are fabricated with different MWCNT loadings: 0 wt% (pure natural rubber), 1 wt%, 3 wt%, and 5 wt%. The specimens are tested for their mechanical properties. It is observed that the tensile strength, hardness and elongation break of CNTs filled rubber composites are remarkably higher than that of raw rubber indicating the inherent reinforcing potential of CNTs. Percentage of the elongation at break of rubber CNTs composites is lower than that of raw rubber.

Tuning the cosmological constant, broken scale invariance, unitarity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Förste, Stefan; Manz, Paul; Physikalisches Institut der Universität Bonn,Nussallee 12, 53115 Bonn

2016-06-10

We study gravity coupled to a cosmological constant and a scale but not conformally invariant sector. In Minkowski vacuum, scale invariance is spontaneously broken. We consider small fluctuations around the Minkowski vacuum. At the linearised level we find that the trace of metric perturbations receives a positive or negative mass squared contribution. However, only for the Fierz-Pauli combination the theory is free of ghosts. The mass term for the trace of metric perturbations can be cancelled by explicitly breaking scale invariance. This reintroduces fine-tuning. Models based on four form field strength show similarities with explicit scale symmetry breaking due tomore » quantisation conditions.« less

A Comparative Study of Some Properties of Cassava and Tree Cassava Starch Films

NASA Astrophysics Data System (ADS)

Belibi, P. C.; Daou, T. J.; Ndjaka, J. M. B.; Nsom, B.; Michelin, L.; Durand, B.

Cassava and tree cassava starch films plasticized with glycerol were produced by casting method. Different glycerol contents (30, 35, 40 and 45 wt. % on starch dry basis) were used and the resulting films were fully characterized. Their water barrier and mechanical properties were compared. While increasing glycerol concentration, moisture content, water solubility, water vapour permeability, tensile strength, percent elongation at break and Young's modulus decreased for both cassava and tree cassava films. Tree cassava films presented better values of water vapour permeability, water solubility and percent elongation at break compared to those of cassava films, regardless of the glycerol content.

Strength Training and Detraining in Different Populations: Case Studies

PubMed Central

Marques, Mário C.; Zajac, Adam; Pereira, Ana; Costa, Aldo M.

2011-01-01

Many researchers have demonstrated that a specific strength training program can improve maximal strength and, the rate of force production, reduce the incidence of muscle-skeletal injury, and contribute to faster injury recovery times, thereby minimizing the number of missed practice sessions or competitions. Yet, to our best knowledge, there is no apparent consensus on the appropriate method of muscle strength and power training to enhance performance in distinct populations groups. Interruptions in training process because of illness, injury, holidays, post-season break or other factors are normal situations in any kind of sport. However, the detraining period and its consequences are not well reported in sports literature, and namely during puberty. Therefore, the aim of this paper was to discuss several case studies concerning different populations such us physical students, age-swimming competitors and elite power athletes. PMID:23487418

Weak reversible cross links may decrease the strength of aligned fiber bundles.

PubMed

Nabavi, S Soran; Hartmann, Markus A

2016-02-21

Reversible cross-linking is an effective strategy to specifically tailor the mechanical properties of polymeric materials that can be found in a variety of biological as well as man-made materials. Using a simple model in this paper the influence of weak, reversible cross-links on the mechanical properties of aligned fiber bundles is investigated. Special emphasis in this analysis is put on the strength of the investigated structures. Using Monte Carlo methods two topologies of cross-links exceeding the strength of the covalent backbone are studied. Most surprisingly only two cross-links are sufficient to break the backbone of a multi chain system, resulting in a reduced strength of the material. The found effect crucially depends on the ratio of inter- to intra-chain cross-links and, thus, on the grafting density that determines this ratio.

Damage development in titanium metal matrix composites subjected to cyclic loading

NASA Technical Reports Server (NTRS)

Johnson, W. S.

1992-01-01

Several layups of SCS-6/Ti-15-3 composites were investigated. Fatigue tests were conducted and analyzed for both notched and unnotched specimens at room temperature and elevated temperatures. Thermo-mechanical fatigue results were analyzed. Test results indicated that the stress in the 0 degree fibers is the controlling factor in fatigue life. The static and fatigue strength of these materials is shown to be strongly dependent on the level of residual stresses and the fiber/matrix interfacial strength. Fatigue tests of notched specimens showed that cracks can initiate and grow many fiber spacings in the matrix materials without breaking fibers. Fiber bridging models were applied to characterize the crack growth behavior. The matrix cracks are shown to significantly reduce the residual strength of notched composites. The notch strength of these composites was accurately predicted using a micromechanics based methodology.

Damage development in titanium metal-matrix composites subjected to cyclic loading

NASA Technical Reports Server (NTRS)

Johnson, W. S.

1993-01-01

Several layups of SCS-6/Ti-15-3 composites were investigated. Fatigue tests were conducted and analyzed for both notched and unnotched specimens at room temperature and elevated temperatures. Thermo-mechanical fatigue results were analyzed. Test results indicated that the stress in the 0 degree fibers is the controlling factor in fatigue life. The static and fatigue strength of these materials is shown to be strongly dependent on the level of residual stresses and the fiber/matrix interfacial strength. Fatigue tests of notched specimens showed that cracks can initiate and grow many fiber spacings in the matrix materials without breaking fibers. Fiber bridging models were applied to characterize the crack growth behavior. The matrix cracks are shown to significantly reduce the residual strength of notched composites. The notch strength of these composites was accurately predicted using a micromechanics based methodology.

Breaking Boundaries: Complementary and Alternative Medicine Provider Framing of Preventive Care.

PubMed

Agarwal, Vinita

2017-11-01

This textual examination extends understandings of how complementary and alternative medicine (CAM) providers constitute preventive care in their discourse by identifying the frame of breaking boundaries referencing relational, structural, and philosophical orientations in their practice with their clients. Analysis of semistructured, in-depth interviews with CAM providers ( n = 17) reveals that the frame of breaking boundaries was comprised of three themes: finding one's own strength; I don't prescribe, so I'm exploring; and ground yourself, and have an escape route. The themes describe preventive care by identifying how CAM providers negotiate their relational positionality in connecting with clients, structural positionality within the field of health care, and philosophical positionality within the ontological understandings that guide how health is defined and conceptualized. The study contributes toward enhancing diverse understandings of constituting preventive care in practice and suggests pragmatic implications for addressing biomedical provider communication with their patients seeking CAM care alongside conventional treatments.

Preparation of UV-protective kefiran/nano-ZnO nanocomposites: physical and mechanical properties.

PubMed

Shahabi-Ghahfarrokhi, Iman; Khodaiyan, Faramarz; Mousavi, Mohammad; Yousefi, Hossein

2015-01-01

In this study, we investigated the effect of ZnO nanoparticles (ZN) as a UV-protective agent of kefiran biopolymers. Our results showed that with increasing ZN content, the tensile strength, elongation at break, and tensile energy to break the kefiran film and nanocomposites also increased. Kefiran nanocomposites with a ZN content higher than 2% produced a UV-protective film with good visual properties, low sensibility to water, and low water-vapor permeability. The thermal properties of all specimens, analyzed by DSC, showed that the ZN content had a negative effect on Tg and a positive effect on nanocomposites' melting point. TEM, SEM micrography and XRD spectrum analysis confirmed the hypothesis that ZNs act like a ball bearing, making movement of kefiran chains easier and increasing elongation at break, while simultaneously decreasing the Tg of kefiran nanocomposites. Copyright © 2014 Elsevier B.V. All rights reserved.

Heat resistance study of basalt fiber material via mechanical tests

NASA Astrophysics Data System (ADS)

Gao, Y. Q.; Jia, C.; Meng, L.; Li, X. H.

2017-12-01

This paper focuses on the study of the relationship between the fracture strength of basalt rovings and temperature. Strong stretching performance of the rovings has been tested after the treatment at fixed temperatures but different heating time and then the fracture strength of the rovings exposed to the heating at different temperatures and cooled in different modes investigated. Finally, the fracture strength of the basalt material after the heat treatment was studied. The results showed that the room-temperature strength tends to decrease with an increase of the heat treatment time at 250 °C, but it has the local maximum after 2h heating. And the basalt rovings strength increased after the heat treatment up to 200 °C. It was 16.7 percent higher than the original strength. The strength depends not only on the temperature and duration of the heating, but also on the cooling mode. The value of the strength measured after cold water cooling was less by 6.3% compared with an ambient air cooling mode. The room-temperature breaking strength of the rovings heated at 200 °C and 100 °C for 2 hours each increased by about 14.6% with respect to unpretreated basalt rovings.

Chiral Symmetry Breaking in Peptide Systems During Formation of Life on Earth.

PubMed

Konstantinov, Konstantin K; Konstantinova, Alisa F

2018-03-01

Chiral symmetry breaking in complex chemical systems with a large number of amino acids and a large number of similar reactions was considered. It was shown that effective averaging over similar reaction channels may result in very weak effective enantioselectivity of forward reactions, which does not allow most of the known models to result in chiral symmetry breaking during formation of life on Earth. Models with simple and catalytic synthesis of a single amino acid, formation of peptides up to length five, and sedimentation of insoluble pair of substances were considered. It was shown that depending on the model and the values of the parameters, chiral symmetry breaking may occur in up to about 10% out of all possible unique insoluble pair combinations even in the absence of any catalytic synthesis and that minimum total number of amino acids in the pair is 5. If weak enantioselective forward catalytic synthesis of amino acids is present, then the number of possible variants, in which chiral symmetry breaking may occur, increases substantially. It was shown that that the most interesting catalysts have zero or one amino acid of "incorrect" chirality. If the parameters of the model are adjusted in such a way to result in an increase of concentration of longer peptides, then catalysts with two amino acids of incorrect chirality start to appear at peptides of length five. Models of chiral symmetry breaking in the presence of epimerization were considered for peptides up to length three. It was shown that the range of parameters in which chiral symmetry breaking could occur significantly shrinks in comparison to previously considered models with peptides up to length two. An experiment of chiral symmetry breaking was proposed. The experiment consists of a three-step cycle: reversible catalytic synthesis of amino acids, reversible synthesis of peptides, and irreversible sedimentation of insoluble substances.

Chiral Symmetry Breaking in Peptide Systems During Formation of Life on Earth

NASA Astrophysics Data System (ADS)

Konstantinov, Konstantin K.; Konstantinova, Alisa F.

2018-03-01

Chiral symmetry breaking in complex chemical systems with a large number of amino acids and a large number of similar reactions was considered. It was shown that effective averaging over similar reaction channels may result in very weak effective enantioselectivity of forward reactions, which does not allow most of the known models to result in chiral symmetry breaking during formation of life on Earth. Models with simple and catalytic synthesis of a single amino acid, formation of peptides up to length five, and sedimentation of insoluble pair of substances were considered. It was shown that depending on the model and the values of the parameters, chiral symmetry breaking may occur in up to about 10% out of all possible unique insoluble pair combinations even in the absence of any catalytic synthesis and that minimum total number of amino acids in the pair is 5. If weak enantioselective forward catalytic synthesis of amino acids is present, then the number of possible variants, in which chiral symmetry breaking may occur, increases substantially. It was shown that that the most interesting catalysts have zero or one amino acid of "incorrect" chirality. If the parameters of the model are adjusted in such a way to result in an increase of concentration of longer peptides, then catalysts with two amino acids of incorrect chirality start to appear at peptides of length five. Models of chiral symmetry breaking in the presence of epimerization were considered for peptides up to length three. It was shown that the range of parameters in which chiral symmetry breaking could occur significantly shrinks in comparison to previously considered models with peptides up to length two. An experiment of chiral symmetry breaking was proposed. The experiment consists of a three-step cycle: reversible catalytic synthesis of amino acids, reversible synthesis of peptides, and irreversible sedimentation of insoluble substances.

Polar Chromospheric Signatures of the Subdued Cycle 23/24 Solar Minimum

NASA Technical Reports Server (NTRS)

Gopalswamy, N.; Yashiro, S.; Makela, P.; Shibasaki, K.; Hathaway, D.

2010-01-01

Coronal holes appear brighter than the quiet Sun in microwave images, with a brightness enhancement of 500 to 2000 K. The brightness enhancement corresponds to the upper chromosphere, where the plasma temperature is about 10000 K. We constructed a microwave butterfly diagram using the synoptic images obtained by the Nobeyama radioheliograph (NoRH) showing the evolution of the polar and low latitude brightness temperature. While the polar brightness reveals the chromospheric conditions, the low latitude brightness is attributed to active regions in the corona. When we compared the microwave butterfly diagram with the magnetic butterfly diagram, we found a good correlation between the microwave brightness enhancement and the polar field strength. The microwave butterfly diagram covers part of solar cycle 22, whole of cycle 23, and part of cycle 24, thus enabling comparison between the cycle 23/24 and cycle 22/23 minima. The microwave brightness during the cycle 23/24 minimum was found to be lower than that during the cycle 22/23 minimum by approximately 250 K. The reduced brightness temperature is consistent with the reduced polar field strength during the cycle 23/24 minimum seen in the magnetic butterfly diagram. We suggest that the microwave brightness at the solar poles is a good indicator of the speed of the solar wind sampled by Ulysses at high latitudes.

Phenology of temperate trees in tropical climates

NASA Astrophysics Data System (ADS)

Borchert, Rolf; Robertson, Kevin; Schwartz, Mark D.; Williams-Linera, Guadalupe

2005-09-01

Several North American broad-leaved tree species range from the northern United States at ˜47°N to moist tropical montane forests in Mexico and Central America at 15-20°N. Along this gradient the average minimum temperatures of the coldest month (T Jan), which characterize annual variation in temperature, increase from -10 to 12°C and tree phenology changes from deciduous to leaf-exchanging or evergreen in the southern range with a year-long growing season. Between 30 and 45°N, the time of bud break is highly correlated with T Jan and bud break can be reliably predicted for the week in which mean minimum temperature rises to 7°C. Temperature-dependent deciduous phenology—and hence the validity of temperature-driven phenology models—terminates in southern North America near 30°N, where T Jan>7°C enables growth of tropical trees and cultivation of frost-sensitive citrus fruits. In tropical climates most temperate broad-leaved species exchange old for new leaves within a few weeks in January-February, i.e., their phenology becomes similar to that of tropical leaf-exchanging species. Leaf buds of the southern ecotypes of these temperate species are therefore not winter-dormant and have no chilling requirement. As in many tropical trees, bud break of Celtis, Quercus and Fagus growing in warm climates is induced in early spring by increasing daylength. In tropical climates vegetative phenology is determined mainly by leaf longevity, seasonal variation in water stress and day length. As water stress during the dry season varies widely with soil water storage, climate-driven models cannot predict tree phenology in the tropics and tropical tree phenology does not constitute a useful indicator of global warming.

New true-triaxial rock strength criteria considering intrinsic material characteristics

NASA Astrophysics Data System (ADS)

Zhang, Qiang; Li, Cheng; Quan, Xiaowei; Wang, Yanning; Yu, Liyuan; Jiang, Binsong

2018-02-01

A reasonable strength criterion should reflect the hydrostatic pressure effect, minimum principal stress effect, and intermediate principal stress effect. The former two effects can be described by the meridian curves, and the last one mainly depends on the Lode angle dependence function. Among three conventional strength criteria, i.e. Mohr-Coulomb (MC), Hoek-Brown (HB), and Exponent (EP) criteria, the difference between generalized compression and extension strength of EP criterion experience a firstly increase then decrease process, and tends to be zero when hydrostatic pressure is big enough. This is in accordance with intrinsic rock strength characterization. Moreover, the critical hydrostatic pressure I_c corresponding to the maximum difference of between generalized compression and extension strength can be easily adjusted by minimum principal stress influence parameter K. So, the exponent function is a more reasonable meridian curves, which well reflects the hydrostatic pressure effect and is employed to describe the generalized compression and extension strength. Meanwhile, three Lode angle dependence functions of L_{{MN}}, L_{{WW}}, and L_{{YMH}}, which unconditionally satisfy the convexity and differential requirements, are employed to represent the intermediate principal stress effect. Realizing the actual strength surface should be located between the generalized compression and extension surface, new true-triaxial criteria are proposed by combining the two states of EP criterion by Lode angle dependence function with a same lode angle. The proposed new true-triaxial criteria have the same strength parameters as EP criterion. Finally, 14 groups of triaxial test data are employed to validate the proposed criteria. The results show that the three new true-triaxial exponent criteria, especially the Exponent Willam-Warnke criterion (EPWW) criterion, give much lower misfits, which illustrates that the EP criterion and L_{{WW}} have more reasonable meridian and deviatoric function form, respectively. The proposed new true-triaxial strength criteria can provide theoretical foundation for stability analysis and optimization of support design of rock engineering.

Relationship between isometric thigh muscle strength and minimum clinically important differences in knee function in osteoarthritis: data from the osteoarthritis initiative.

PubMed

Ruhdorfer, Anja; Wirth, Wolfgang; Eckstein, Felix

2015-04-01

To determine the relationship between thigh muscle strength and clinically relevant differences in self-assessed lower leg function. Isometric knee extensor and flexor strength of 4,553 Osteoarthritis Initiative participants (2,651 women and 1,902 men) was related to the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) physical function scores by linear regression. Further, groups of male and female participant strata with minimum clinically important differences (MCIDs) in WOMAC function scores (6 of 68 units) were compared across the full range of observed values and to participants without functional deficits (WOMAC score 0). The effect of WOMAC knee pain and body mass index on the above relationships was explored using stepwise regression. Per regression equations, a 3.7% reduction in extensor strength and a 4.0% reduction in flexor strength were associated with an MCID in WOMAC function in women, and, respectively, a 3.6% and 4.8% reduction in men. For strength divided by body weight, reductions were 5.2% and 6.7%, respectively, in women and 5.8% and 6.7%, respectively, in men. Comparing MCID strata across the full observed range of WOMAC function confirmed the above estimates and did not suggest nonlinear relationships across the spectrum of observed values. WOMAC pain correlated strongly with WOMAC function, but extensor (and flexor) muscle strength contributed significant independent information. Reductions of approximately 4% in isometric muscle strength and of 6% in strength per body weight were related to a clinically relevant difference in WOMAC functional disability. Longitudinal studies will need to confirm these relationships within persons. Muscle extensor (and flexor) strength (per body weight) provided significant independent information in addition to pain in explaining variability in lower leg function. Copyright © 2015 by the American College of Rheumatology.

Frost injury to bitterbrush in eastern California

Treesearch

R. S. Smith; R. F. Scharpf; E. R. Schneegas

1965-01-01

Widespread dieback of Purshia tridentata, on the Inyo National Forest in eastern California in the spring of 1964, was caused by a severe 3-day frost with daily minimums down to 13°F. An unusually warm 9-day period-with temperatures up to 70°F., which preceded the frost by a week, had induced the bitterbrush to break dormancy and start shoot elongation when the frost...

Celeris: A GPU-accelerated open source software with a Boussinesq-type wave solver for real-time interactive simulation and visualization

NASA Astrophysics Data System (ADS)

Tavakkol, Sasan; Lynett, Patrick

2017-08-01

In this paper, we introduce an interactive coastal wave simulation and visualization software, called Celeris. Celeris is an open source software which needs minimum preparation to run on a Windows machine. The software solves the extended Boussinesq equations using a hybrid finite volume-finite difference method and supports moving shoreline boundaries. The simulation and visualization are performed on the GPU using Direct3D libraries, which enables the software to run faster than real-time. Celeris provides a first-of-its-kind interactive modeling platform for coastal wave applications and it supports simultaneous visualization with both photorealistic and colormapped rendering capabilities. We validate our software through comparison with three standard benchmarks for non-breaking and breaking waves.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shiogama, Hideo; Imada, Yukiko; Mori, Masato

Here, we describe two unprecedented large (100-member), longterm (61-year) ensembles based on MRI-AGCM3.2, which were driven by historical and non-warming climate forcing. These ensembles comprise the "Database for Policy Decision making for Future climate change (d4PDF)". We compare these ensembles to large ensembles based on another climate model, as well as to observed data, to investigate the influence of anthropogenic activities on historical changes in the numbers of record-breaking events, including: the annual coldest daily minimum temperature (TNn), the annual warmest daily maximum temperature (TXx) and the annual most intense daily precipitation event (Rx1day). These two climate model ensembles indicatemore » that human activity has already had statistically significant impacts on the number of record-breaking extreme events worldwide mainly in the Northern Hemisphere land. Specifically, human activities have altered the likelihood that a wider area globally would suffer record-breaking TNn, TXx and Rx1day events than that observed over the 2001- 2010 period by a factor of at least 0.6, 5.4 and 1.3, respectively. However, we also find that the estimated spatial patterns and amplitudes of anthropogenic impacts on the probabilities of record-breaking events are sensitive to the climate model and/or natural-world boundary conditions used in the attribution studies.« less

The Effects of Spectral Nudging on Arctic Temperature and Precipitation Extremes as Produced by the Pan-Arctic WRF

NASA Astrophysics Data System (ADS)

Glisan, J. M.; Gutowski, W. J.; Higgins, M.; Cassano, J. J.

2011-12-01

Pan-Arctic WRF (PAW) simulations produced using the 50-km wr50a domain developed for the fully-coupled Regional Arctic Climate Model (RACM) were found to produce deep atmospheric circulation biases over the northern Pacific Ocean, manifested in pressure, geopotential height, and temperature fields. Various remedies were unsuccessfully tested to correct these large biases, such as modifying the physical domain or using different initial/boundary conditions. Spectral (interior) nudging was introduced as a way of constraining the model to be more consistent with observed behavior. However, such control over numerical model behavior raises concerns over how much nudging may affect unforced variability and extremes. Strong nudging may reduce or filter out extreme events, since the nudging pushes the model toward a relatively smooth, large-scale state. The question then becomes - what is the minimum spectral nudging needed to correct the biases occurring on the RACM domain while not limiting PAW simulation of extreme events? To determine this, case studies were devised, using a six-member PAW ensemble on the RACM grid with varying spectral nudging strength. Two simulations were run, one in the cold season (January 2007) and one in a warm season (July 2007). Precipitation and 2-m temperature fields were extracted from the output and analyzed to determine how changing spectral nudging strength impacts both temporal and spatial temperature and precipitation extremes. The maximum and minimum temperatures at each point from among the ensemble members were examined, on the 95th confidence interval. The maximum and minimums over the simulation period will also be considered. Results suggest that there is a marked lack of sensitivity to the degrees of nudging. Moreover, it appears nudging strength can be considerably smaller than the standard strength and still produce reliably good simulations.

On the non-existence of a sharp cooling break in gamma-ray burst afterglow spectra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uhm, Z. Lucas; Zhang, Bing, E-mail: uhm@physics.unlv.edu, E-mail: zhang@physics.unlv.edu

Although the widely used analytical afterglow model of gamma-ray bursts (GRBs) predicts a sharp cooling break ν {sub c} in its afterglow spectrum, the GRB observations so far rarely show clear evidence for a cooling break in their spectra or a corresponding temporal break in their light curves. Employing a Lagrangian description of the blast wave, we conduct a sophisticated calculation of the afterglow emission. We precisely follow the cooling history of non-thermal electrons accelerated into each Lagrangian shell. We show that a detailed calculation of afterglow spectra does not in fact give rise to a sharp cooling break atmore » ν {sub c}. Instead, it displays a very mild and smooth transition, which occurs gradually over a few orders of magnitude in energy or frequency. The main source of this slow transition is that different mini shells have different evolutionary histories of the comoving magnetic field strength B, so that deriving the current value of ν {sub c} of each mini shell requires an integration of its cooling rate over the time elapsed since its creation. We present the time evolution of optical and X-ray spectral indices to demonstrate the slow transition of spectral regimes and discuss the implications of our result in interpreting GRB afterglow data.« less

Can nature's design be improved upon? High strength, transparent nacre-like nanocomposites with double network of sacrificial cross links.

PubMed

Podsiadlo, Paul; Kaushik, Amit K; Shim, Bong Sup; Agarwal, Ashish; Tang, Zhiyong; Waas, Anthony M; Arruda, Ellen M; Kotov, Nicholas A

2008-11-20

The preparation of a high-strength and highly transparent nacre-like nanocomposite via layer-by-layer assembly technique from poly(vinyl alcohol) (PVA) and Na+-montmorillonite clay nanosheets is reported in this article. We show that a high density of weak bonding interactions between the polymer and the clay particles: hydrogen, dipole-induced dipole, and van der Waals undergoing break-reform deformations, can lead to high strength nanocomposites: sigmaUTS approximately 150 MPa and E' approximately 13 GPa. Further introduction of ionic bonds into the polymeric matrix creates a double network of sacrificial bonds which dramatically increases the mechanical properties: sigmaUTS approximately 320 MPa and E' approximately 60 GPa.

Truncated disc surface brightness profiles produced by flares

NASA Astrophysics Data System (ADS)

Borlaff, Alejandro; Eliche-Moral, M. Carmen; Beckman, John; Font, Joan

2017-03-01

Previous studies have discarded that flares in galactic discs may explain the truncation that are frequently observed in highly-inclined galaxies (Kregel et al. 2002). However, no study has systematically analysed this hypothesis using realistic models for the disc, the flare and the bulge. We derive edge-on and face-on surface brightness profiles for a series of realistic galaxy models with flared discs that sample a wide range of structural and photometric parameters across the Hubble Sequence, accordingly to observations. The surface brightness profile for each galaxy model has been simulated for edge-on and face-on views to find out whether the flared disc produces a significant truncation in the disc in the edge-on view compared to the face-on view or not. In order to simulate realistic images of disc galaxies, we have considered the observational distribution of the photometric parameters as a function of the morphological type for three mass bins (10 < log10(M/M ⊙) < 10.7, 10.7 < log10(M/M ⊙) < 11 and log10(M/M ⊙) > 11), and four morphological type bins (S0-Sa, Sb-Sbc, Sc-Scd and Sd-Sdm). For each mass bin, we have restricted the photometric and structural parameters of each modelled galaxy to their characteristic observational ranges (μ0, disc, μeff, bulge, B/T, M abs, r eff, n bulge, h R, disc) and the flare in the disc (h z, disc/h R, disc, ∂h z, disc/∂R, see de Grijs & Peletier 1997, Graham 2001, López-Corredoira et al. 2002, Yoachim & Dalcanton 2006, Bizyaev et al. 2014, Mosenkov et al. 2015). Contrary to previous claims, the simulations show that realistic flared disks can be responsible for the truncations observed in many edge-on systems, preserving the profile of the non-flared analogous model in face-on view. These breaks reproduce the properties of the weak-to-intermediate breaks observed in many real Type-II galaxies in the diagram relating the radial location of the break (R brkII) in units of the inner disk scale-length with the break strength S (Laine et al. 2014). Radial variation of the scale-height of the disc (flaring) can explain the existence of many breaks in edge-on galaxies, especially of those with low break strengths 10\\frac{ho}{hi} \\sim \\ [-0.3,-0.1]$ .

The mechanism of earthquake

NASA Astrophysics Data System (ADS)

Lu, Kunquan; Cao, Zexian; Hou, Meiying; Jiang, Zehui; Shen, Rong; Wang, Qiang; Sun, Gang; Liu, Jixing

2018-03-01

The physical mechanism of earthquake remains a challenging issue to be clarified. Seismologists used to attribute shallow earthquake to the elastic rebound of crustal rocks. The seismic energy calculated following the elastic rebound theory and with the data of experimental results upon rocks, however, shows a large discrepancy with measurement — a fact that has been dubbed as “the heat flow paradox”. For the intermediate-focus and deep-focus earthquakes, both occurring in the region of the mantle, there is not reasonable explanation either. This paper will discuss the physical mechanism of earthquake from a new perspective, starting from the fact that both the crust and the mantle are discrete collective system of matters with slow dynamics, as well as from the basic principles of physics, especially some new concepts of condensed matter physics emerged in the recent years. (1) Stress distribution in earth’s crust: Without taking the tectonic force into account, according to the rheological principle of “everything flows”, the normal stress and transverse stress must be balanced due to the effect of gravitational pressure over a long period of time, thus no differential stress in the original crustal rocks is to be expected. The tectonic force is successively transferred and accumulated via stick-slip motions of rock blocks to squeeze the fault gouge and then exerted upon other rock blocks. The superposition of such additional lateral tectonic force and the original stress gives rise to the real-time stress in crustal rocks. The mechanical characteristics of fault gouge are different from rocks as it consists of granular matters. The elastic moduli of the fault gouges are much less than those of rocks, and they become larger with increasing pressure. This peculiarity of the fault gouge leads to a tectonic force increasing with depth in a nonlinear fashion. The distribution and variation of the tectonic stress in the crust are specified. (2) The strength of crust rocks: The gravitational pressure can initiate the elasticity-plasticity transition in crust rocks. By calculating the depth dependence of elasticity-plasticity transition and according to the actual situation analysis, the behaviors of crust rocks can be categorized in three typical zones: elastic, partially plastic and fully plastic. As the proportion of plastic portion reaches about 10% in the partially plastic zone, plastic interconnection may occur and the variation of shear strength in rocks is mainly characterized by plastic behavior. The equivalent coefficient of friction for the plastic slip is smaller by an order of magnitude, or even less than that for brittle fracture, thus the shear strength of rocks by plastic sliding is much less than that by brittle breaking. Moreover, with increasing depth a number of other factors can further reduce the shear yield strength of rocks. On the other hand, since earthquake is a large-scale damage, the rock breaking must occur along the weakest path. Therefore, the actual fracture strength of rocks in a shallow earthquake is assuredly lower than the average shear strength of rocks as generally observed. The typical distributions of the average strength and actual fracture strength in crustal rocks varying with depth are schematically illustrated. (3) The conditions for earthquake occurrence and mechanisms of earthquake: An earthquake will lead to volume expansion, and volume expansion must break through the obstacle. The condition for an earthquake to occur is as follows: the tectonic force exceeds the sum of the fracture strength of rock, the friction force of fault boundary and the resistance from obstacles. Therefore, the shallow earthquake is characterized by plastic sliding of rocks that break through the obstacles. Accordingly, four possible patterns for shallow earthquakes are put forward. Deep-focus earthquakes are believed to result from a wide-range rock flow that breaks the jam. Both shallow earthquakes and deep-focus earthquakes are the energy release caused by the slip or flow of rocks following a jamming-unjamming transition. (4) The energetics and impending precursors of earthquake: The energy of earthquake is the kinetic energy released from the jamming-unjamming transition. Calculation shows that the kinetic energy of seismic rock sliding is comparable with the total work demanded for rocks’ shear failure and overcoming of frictional resistance. There will be no heat flow paradox. Meanwhile, some valuable seismic precursors are likely to be identified by observing the accumulation of additional tectonic forces, local geological changes, as well as the effect of rock state changes, etc.

Synapse Specificity of Long-Term Potentiation Breaks Down with Aging

ERIC Educational Resources Information Center

Ris, Laurence; Godaux, Emile

2007-01-01

Memory shows age-related decline. According to the current prevailing theoretical model, encoding of memories relies on modifications in the strength of the synapses connecting the different cells within a neuronal network. The selective increases in synaptic weight are thought to be biologically implemented by long-term potentiation (LTP). Here,…

49 CFR 215.5 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS General § 215.5 Definitions. As used in this part: (a) Break... significantly diminish the strength of the member are not considered to be “cracked”; (c) Railroad freight car means a car designed to carry freight, or railroad personnel, by rail and includes a: (1) Box car; (2...

49 CFR 215.5 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS General § 215.5 Definitions. As used in this part: (a) Break... significantly diminish the strength of the member are not considered to be “cracked”; (c) Railroad freight car means a car designed to carry freight, or railroad personnel, by rail and includes a: (1) Box car; (2...

49 CFR 215.5 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS General § 215.5 Definitions. As used in this part: (a) Break... significantly diminish the strength of the member are not considered to be “cracked”; (c) Railroad freight car means a car designed to carry freight, or railroad personnel, by rail and includes a: (1) Box car; (2...

49 CFR 215.5 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS General § 215.5 Definitions. As used in this part: (a) Break... significantly diminish the strength of the member are not considered to be “cracked”; (c) Railroad freight car means a car designed to carry freight, or railroad personnel, by rail and includes a: (1) Box car; (2...

Access to Higher Education by the Luck of the Draw

ERIC Educational Resources Information Center

Stone, Peter

2013-01-01

Random selection is a fair way to break ties between applicants of equal merit seeking admission to institutions of higher education (with "merit" defined here in terms of the intrinsic contribution higher education would make to the applicant's life). Opponents of random selection commonly argue that differences in strength between…

46 CFR 163.002-21 - Approval tests.

Code of Federal Regulations, 2011 CFR

2011-10-01

... must not break or crack during these tests. (2) Platform strength. If the pilot hoist has a lift... deck interlock must prevent movement of the ladder or lift platform when the lever is activated. (4... of the hoist is placed on its ladder or lift platform. The ladder or lift platform is repeatedly...

46 CFR 164.023-7 - Performance; non-standard thread.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Performance; non-standard thread. 164.023-7 Section 164... Performance; non-standard thread. (a) Use Codes 1, 2, 3, 4BC, 4RB, 5 (any). Each non-standard thread which...) testing machine. (2) Single strand breaking strength (after weathering). After exposure in a sunshine...

46 CFR 164.023-7 - Performance; non-standard thread.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Performance; non-standard thread. 164.023-7 Section 164... Performance; non-standard thread. (a) Use Codes 1, 2, 3, 4BC, 4RB, 5 (any). Each non-standard thread which...) testing machine. (2) Single strand breaking strength (after weathering). After exposure in a sunshine...

None but Ourselves Can Free Our Minds: Critical Computational Literacy as a Pedagogy of Resistance

ERIC Educational Resources Information Center

Lee, Clifford H.; Soep, Elisabeth

2016-01-01

Critical computational literacy (CCL) is a new pedagogical and conceptual framework that combines the strengths of critical literacy and computational thinking. Through CCL, young people conceptualize, create, and disseminate digital projects that break silences, expose important truths, and challenge unjust systems, all the while building skills…

The Seeking of Self: Voices of the Abandoned in the Work of Brock Cole.

ERIC Educational Resources Information Center

Smith, S. Scot

1999-01-01

Presents three young adult novels by Brock Cole discussing a phenomenological quest for self-identity that breaks the traditional pattern often found in young adult literature. Discusses the novels "The Goats" (1987), "Celine" (1989), and "The Facts Speak for Themselves" (1997) where adolescents show strength,…

A comparative study of ground tire rubber devulcanization using twin screw extruder and internal mixer

NASA Astrophysics Data System (ADS)

Ujianto, O.; Putri, D. B.; Jayatin; AWinarto, D.

2017-07-01

Devulcanization of ground tire rubber (GTR) was done using twin screw extruder (TSE) and internal mixer (IM). Processing parameters were varied to analyze its effect on gel content. Fourier Transform Infrared Spectroscopy (FTIR) analysis was performed as qualitative technique to confirm structural change. The devulcanized rubbers with the least gel content percentage produced in both TSE and IM were then used as filler in natural rubber (NR)/coconut coir (CC) composite preparation. Effects of gel content percentage on NR/CC composite tensile strength and elongation at break were analyzed. The results show that the gel content decreased by 41% for sample processed in TSE and 50% in IM compared to control sample. Overall, the devulcanization is influenced by high energy generated by thermal or thermo-mechanical process. FTIR spectra show chemically structural changes of GTR as C=C, CH2, CH3 with higher intensity for IM sample than its counterpart indicated devulcanization. The replacement of GTR to DGTR on NR/CC/GTR composites provided less network structures and resulted better tensile strength and elongation at break.

Weakly and strongly coupled Belousov-Zhabotinsky patterns.

PubMed

Weiss, Stephan; Deegan, Robert D

2017-02-01

We investigate experimentally and numerically the synchronization of two-dimensional spiral wave patterns in the Belousov-Zhabotinsky reaction due to point-to-point coupling of two separate domains. Different synchronization modalities appear depending on the coupling strength and the initial patterns in each domain. The behavior as a function of the coupling strength falls into two qualitatively different regimes. The weakly coupled regime is characterized by inter-domain interactions that distorted but do not break wave fronts. Under weak coupling, spiral cores are pushed around by wave fronts in the other domain, resulting in an effective interaction between cores in opposite domains. In the case where each domain initially contains a single spiral, the cores form a bound pair and orbit each other at quantized distances. When the starting patterns consist of multiple randomly positioned spiral cores, the number of cores decreases with time until all that remains are a few cores that are synchronized with a partner in the other domain. The strongly coupled regime is characterized by interdomain interactions that break wave fronts. As a result, the wave patterns in both domains become identical.

Weakly and strongly coupled Belousov-Zhabotinsky patterns

NASA Astrophysics Data System (ADS)

Weiss, Stephan; Deegan, Robert D.

2017-02-01

We investigate experimentally and numerically the synchronization of two-dimensional spiral wave patterns in the Belousov-Zhabotinsky reaction due to point-to-point coupling of two separate domains. Different synchronization modalities appear depending on the coupling strength and the initial patterns in each domain. The behavior as a function of the coupling strength falls into two qualitatively different regimes. The weakly coupled regime is characterized by inter-domain interactions that distorted but do not break wave fronts. Under weak coupling, spiral cores are pushed around by wave fronts in the other domain, resulting in an effective interaction between cores in opposite domains. In the case where each domain initially contains a single spiral, the cores form a bound pair and orbit each other at quantized distances. When the starting patterns consist of multiple randomly positioned spiral cores, the number of cores decreases with time until all that remains are a few cores that are synchronized with a partner in the other domain. The strongly coupled regime is characterized by interdomain interactions that break wave fronts. As a result, the wave patterns in both domains become identical.

A torque, tension and stress corrosion evaluation of high strength A286 bolts

NASA Technical Reports Server (NTRS)

Montano, J. W.

1986-01-01

The problems associated with overtorque applied to the Booster Separation Motor (BSM) Igniter Adapter high strength 200 KSI (1379 Mpa) A286 CRES bolts and the threaded holes of the 7075-T73 aluminum alloy BSM cases are addressed. The evaluation included torque, tensile, and stress corrosion tests incorporating the A286 CRES bolts and the 7075-T73 aluminum alloy BSM cases. The tensile test data includes ultimate tensile load (UTL), Johnson's 2/3 yield load (J2/3YL), proportional limit load (PLL), and total bolt stretch. Torque tension data includes torque, torque induced load, and positive and negative break-away torque. Stress corrosion test data reflect the overtorque and the resulting torque induced loads sustained by the A286 CRES bolts torqued into a 7075-T73 aluminum alloy forged dome with threaded holes. After 60 days of salt fog exposure, the positive and the negative break-away torques, the subsequent mechanical property tensile test results, and the BSM dome threaded hole axial tensile pullout loads are reported.

Modeling bipolar stimulation of cardiac tissue

NASA Astrophysics Data System (ADS)

Galappaththige, Suran K.; Gray, Richard A.; Roth, Bradley J.

2017-09-01

Unipolar stimulation of cardiac tissue is often used in the design of cardiac pacemakers because of the low current required to depolarize the surrounding tissue at rest. However, the advantages of unipolar over bipolar stimulation are not obvious at shorter coupling intervals when the tissue near the pacing electrode is relatively refractory. Therefore, this paper analyzes bipolar stimulation of cardiac tissue. The strength-interval relationship for bipolar stimulation is calculated using the bidomain model and a recently developed parsimonious ionic current model. The strength-interval curves obtained using different electrode separations and arrangements (electrodes placed parallel to the fibers versus perpendicular to the fibers) indicate that bipolar stimulation results in more complex activation patterns compared to unipolar stimulation. An unusually low threshold stimulus current is observed when the electrodes are close to each other (a separation of 1 mm) because of break excitation. Unlike for unipolar stimulation, anode make excitation is not present during bipolar stimulation, and an abrupt switch from anode break to cathode make excitation can cause dramatic changes in threshold with very small changes in the interval. These results could impact the design of implantable pacemakers and defibrillators.

Structural analysis, and antioxidant and antibacterial properties of chitosan-poly (vinyl alcohol) biodegradable films.

PubMed

Hajji, Sawssen; Chaker, Achraf; Jridi, Mourad; Maalej, Hana; Jellouli, Kemel; Boufi, Sami; Nasri, Moncef

2016-08-01

The development and characterization of biodegradable blend films based on chitosan and poly (vinyl alcohol) for possible use in a variety of biological activities are reported. Fourier transform infrared spectroscopy (FTIR) spectra of chitosan-poly (vinyl alcohol) (Ch/PVA) films showed characteristics peaks shifting to a lower frequency range due to hydrogen bonding between -OH of PVA and -NH2 of chitosan. The chitosan and PVA polymers presented good compatibility. The morphology study of chitosan and composite films showed a compact and homogenous structure. The tensile strength and elongation at break increased with PVA content. In fact, the highest tensile strength and elongation at break (53.58 MPa and 454 %) occurs with pure PVA film. The results showed that PVA incorporation in the blends contributes to increase the intermolecular interactions, thus improving the mechanical properties. In addition, the prepared films demonstrated high antioxidant activities monitored by 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical-scavenging, reducing power, and β-carotene bleaching activity. Nevertheless, PVA addition reduced antioxidant and antibacterial activities against Gram-positive and Gram-negative bacteria tested.

UNCOVERING THE INTRINSIC VARIABILITY OF GAMMA-RAY BURSTS

NASA Astrophysics Data System (ADS)

Golkhou, V. Zach; Butler, Nathaniel R

2014-08-01

We develop a robust technique to determine the minimum variability timescale for gamma-ray burst (GRB) light curves, utilizing Haar wavelets. Our approach averages over the data for a given GRB, providing an aggregate measure of signal variation while also retaining sensitivity to narrow pulses within complicated time series. In contrast to previous studies using wavelets, which simply define the minimum timescale in reference to the measurement noise floor, our approach identifies the signature of temporally smooth features in the wavelet scaleogram and then additionally identifies a break in the scaleogram on longer timescales as a signature of a true, temporally unsmooth light curve feature or features. We apply our technique to the large sample of Swift GRB gamma-ray light curves and for the first time—due to the presence of a large number of GRBs with measured redshift—determine the distribution of minimum variability timescales in the source frame. We find a median minimum timescale for long-duration GRBs in the source frame of Δtmin = 0.5 s, with the shortest timescale found being on the order of 10 ms. This short timescale suggests a compact central engine (3000 km). We discuss further implications for the GRB fireball model and present a tantalizing correlation between the minimum timescale and redshift, which may in part be due to cosmological time dilation.

Improved Ablation Resistance of Silicone Rubber Composites by Introducing Montmorillonite and Silicon Carbide Whisker

PubMed Central

Zhang, Guangwu; Wang, Fuzhong; Huang, Zhixiong; Dai, Jing; Shi, Minxian

2016-01-01

Montmorillonite (MMT) was added to silicone rubber (SR) to improve the ablation resistance of the silicone. Following this, different quantities of silicon carbide whiskers (SiCw) were incorporated into the MMT/SR to yield a hybrid, ablative composite. The tensile strength and elongation at break of the composite increased after the addition of MMT. The ablation test results showed that MMT helped to form a covering layer by bonding with the silica and other components on the ablated surface. The linear and mass ablation rates exhibited decreases of 22.5% and 18.2%, respectively, in comparison to a control sample. After further incorporation of SiCw as the second filler, the resulting composites exhibited significantly higher tensile strength and ablation resistance, but not particularly lower elongation at break in comparison to the control sample. The SiCw/MMT fillers were beneficial in forming a dense and compact covering layer that delayed the heat and oxygen diffusion into the inner layers, which improved the ablation properties effectively. The remaining whiskers acted as a micro skeleton to maintain the composite’s char strength. Compared to the control sample, the linear and mass ablation rates of the composite after incorporating 6 phr SiCw and 10 phr MMT decreased by 59.2% and 43.6%, respectively. These experimental results showed that the fabricated composites exhibited outstanding mechanical properties and excellent ablation resistance. PMID:28773846

Physical Characteristics of Coleus tuberosus Flour and Noodle in Various Arenga Starch Substitution

NASA Astrophysics Data System (ADS)

Miftakhussolikhah; Ariani, D.; Angwar, M.; Kevin, J.

2017-04-01

Coleus tuberosus is one of local commodities in Indonesia which contains high carbohydrate. However, its utilization does note maximally. Therefore, C. tuberosus made into flour by grater method, and then used for noodle making with arenga strach as substituting material. The aim of this study was to determine the effect of C. tuberosus flour substitution in noodle preparation from arenga starch on its textural and sensory properties. In this study, noodle was made in some variations which were 100% arenga starch; 75% arenga starch:25% C. tuberosus flour; 50% arenga starch:50% C. tuberosus flour; 25% arenga starch:75% C. tuberosus flour and 100% C. tuberosus flour. Characterization of noodle were investigated including water content, strength, tensile strength, strain at break and stickiness. Sensory evaluation was conducted to analyse consumers acceptance. Noodle was compared with two commercial products. The result showed that arenga starch substitution in C. tuberosus noodle affect textural properties of noodle. The higher concentration of C. tuberosus flour caused tensile strength and strain at break getting low. The water content and stickiness were increased as the C. tuberosus flour substitution ratio increase. None of the noodle resulted from C. tuberosus flour and arenga starch mixture was exactly as same as maize and rice commercial noodles. However 25% of C.tuberosus noodle has better characteristics than other C.tuberosus noodles.

Improved Ablation Resistance of Silicone Rubber Composites by Introducing Montmorillonite and Silicon Carbide Whisker.

PubMed

Zhang, Guangwu; Wang, Fuzhong; Huang, Zhixiong; Dai, Jing; Shi, Minxian

2016-08-24

Montmorillonite (MMT) was added to silicone rubber (SR) to improve the ablation resistance of the silicone. Following this, different quantities of silicon carbide whiskers (SiCw) were incorporated into the MMT/SR to yield a hybrid, ablative composite. The tensile strength and elongation at break of the composite increased after the addition of MMT. The ablation test results showed that MMT helped to form a covering layer by bonding with the silica and other components on the ablated surface. The linear and mass ablation rates exhibited decreases of 22.5% and 18.2%, respectively, in comparison to a control sample. After further incorporation of SiCw as the second filler, the resulting composites exhibited significantly higher tensile strength and ablation resistance, but not particularly lower elongation at break in comparison to the control sample. The SiCw/MMT fillers were beneficial in forming a dense and compact covering layer that delayed the heat and oxygen diffusion into the inner layers, which improved the ablation properties effectively. The remaining whiskers acted as a micro skeleton to maintain the composite's char strength. Compared to the control sample, the linear and mass ablation rates of the composite after incorporating 6 phr SiCw and 10 phr MMT decreased by 59.2% and 43.6%, respectively. These experimental results showed that the fabricated composites exhibited outstanding mechanical properties and excellent ablation resistance.

Utilization of mango seed starch in manufacture of bioplastic reinforced with microparticle clay using glycerol as plasticizer

NASA Astrophysics Data System (ADS)

Maulida; Kartika, T.; Harahap, M. B.; Ginting, M. H. S.

2018-02-01

Bioplastics are plastics that can be used just like conventional plastics but will disintegrate by the activity of microorganisms into water and carbon dioxide. Starch is a natural polymer material that can used for bioplastic production. The addition of reinforcing particles has been shown to improve the mechanical properties of bioplastics. The aim of this research is to know the potency of mango seed starch and microparticle clay as filler and glycerol concentration as plasticizer on tensile strength and elongation at break, functional group (FTIR) and surface morphology (SEM). In this study used mango seed starch size of 5 grams, with the variation of clay filler mass of 0; 3; 6 and nine wt%, while the mass of glycerol with a variation of 0; 20; 25; 30; And 35% wt. The heating temperature of the bioplastics solution used was 80.53 °C. The resulting bioplastics was analyzed for their physical and chemical properties, including FTIR, SEM, tensile strength, elongation at break. The FTIR analysis shows that no new functional groups was formed. From the analysis of mango starch content obtained 62.82%, 44.0% amylopectin content, amylose content 14.82%, and water content 12.65%. In this study obtained bioplastics with the best conditions on the use of 6% clay and 25% glycerol, with a tensile strength of 5.657MPa, percent elongation at breakup 43.431%.

Recyclable plastics as substrata for settlement and growth of bryozoans Bugula neritina and barnacles Amphibalanus amphitrite.

PubMed

Li, Heng-Xiang; Orihuela, Beatriz; Zhu, Mei; Rittschof, Daniel

2016-11-01

Plastics are common and pervasive anthropogenic debris in marine environments. Floating plastics provide opportunities to alter the abundance, distribution and invasion potential of sessile organisms that colonize them. We selected plastics from seven recycle categories and quantified settlement of (i) bryozoans Bugula neritina (Linnaeus, 1758) in the lab and in the field, and of (ii) barnacles Amphibalanus (= Balanus) amphitrite (Darwin, 1854) in the field. In the laboratory we cultured barnacles on the plastics for 8 weeks and quantified growth, mortality, and breaking strength of the side plates. In the field all recyclable plastics were settlement substrata for bryozoans and barnacles. Settlement depended on the type of plastic. Fewer barnacles settled on plastic surfaces compared to glass. In the lab and in the field, bryozoan settlement was higher on plastics than on glass. In static laboratory rearing, barnacles growing on plastics were initially significantly smaller than on glass. This suggested juvenile barnacles were adversely impacted by materials leaching from the plastics. Barnacle mortality was not significantly different between plastic and glass surfaces, but breaking strength of side plates of barnacles on polyvinyl chloride (PVC) and polycarbonate (PC) were significantly lower than breakage strength on glass. Plastics impact marine ecosystems directly by providing new surfaces for colonization with fouling organisms and by contaminants shown previously to leach out of plastics and impact biological processes. Published by Elsevier Ltd.

The Energy Spectrum of Solar Energetic Electrons

NASA Astrophysics Data System (ADS)

Wang, L.; Yang, L.; Krucker, S.; Wimmer-Schweingruber, R. F.; Bale, S. D.

2015-12-01

Here we present a statistical survey of the energy spectrum of solar energetic electron events (SEEs) observed by the WIND 3DP instrument from 1995 though 2014. For SEEs with the minimum energy below 10 keV and the maximum energy above 100 keV, ~85% (~2%) have a double-power-law energy spectrum with a steepening (hardening) above the break energy, while ~13% have a single-power-law energy spectrum at all energies. The average spectral index is ~2.4 below the energy break and is ~4.0 above the energy break. For SEEs detected only at energies <10 keV (>20 keV), they generally show a single-power-law spectrum with the average index of ~3.0 (~3.3). The spectrum of SEEs detected only below 10 keV appears to get harder with increasing solar activity, but the spectrum of SEEs with higher-energy electrons shows no clear correlation with solar activity. We will also investigate whether the observed energy spectrum of SEEs at 1 AU mainly reflects the electron acceleration at the Sun or the electron transport in the interplanetary medium.

Simulating Hydraulic Fracturing: Failure in soft versus hard rocks

NASA Astrophysics Data System (ADS)

Aleksans, J.; Koehn, D.; Toussaint, R.

2017-12-01

In this contribution we discuss the dynamic development of hydraulic fractures, their evolution and the resulting seismicity during fluid injection in a coupled numerical model. The model describes coupling between a solid that can fracture dynamically and a compressible fluid that can push back at the rock and open fractures. With a series of numerical simulations we show how the fracture pattern and seismicity change depending on changes in depth, injection rate, Young's Modulus and breaking strength. Our simulations indicate that the Young's Modulus has the largest influence on the fracture dynamics and also the related seismicity. Simulations of rocks with a Young's modulus smaller than 10 GPa show dominant mode I failure and a growth of fracture aperture with a decrease in Young's modulus. Simulations of rocks with a higher Young's modulus than 10 GPa show fractures with a constant aperture and fracture growth that is mainly governed by a growth in crack length and an increasing amount of mode II failure. We propose that two distinct failure regimes are observed in the simulations, above 10 GPa rocks break with a constant critical stress intensity factor whereas below 10 GPa they break reaching a critical cohesion, i.e. a critical tensile strength. These results are very important for the prediction of fracture dynamics and seismicity during fluid injection, especially since we see a transition from one failure regime to another at around 10 GPa, a Young's modulus that lies in the middle of possible values for natural shale rocks.

The effect of cellulose nanocrystal (CNC) from rattan biomass as filler and citric acid as co-plasticizer on tensile properties of sago starch biocomposite

NASA Astrophysics Data System (ADS)

Nasution, Halimatuddahliana; Harahap, Hamidah; Afandy, Yayang; Fath, M. Thoriq Al

2017-11-01

Biocomposite containing cellulose nanocrystals (CNC) from rattan biomass as fillers and citric acid as co-plasticizer. Rattan biomass is a fiber waste from processing industry of rattan which contains 37.6% cellulose. Isolation of alpha cellulose from rattan biomass was prepared by using three stages: delignification, alkalization, and bleaching. It was delignificated with 3.5% HNO3 and NaNO2, precipitated with 17.5% NaOH, bleaching process with 10% H2O2. The preparation of CNC includes acid hydrolysis using 45% H2SO4 and followed by mechanical processes of ultrasonication, centrifugation, and filtration with a dialysis membrane. Biocomposite was prepared using a solution casting method, which includes 1-4 wt % CNC as fillers, 10-40 wt% citric acid as co-plasticizer and 30 wt% glycerol as plasticizer. The results of TGA, SEM and XRD characteristic of CNC show that CNC has low residue mass, rod like and network like shape with crystallinity index 84.46%. Biocomposite characteristic consists of SEM, tensile strength and elongation at break. The resultshows that biocomposites by addition of CNC and citric acid have a smooth surface and homogeneous distribution of fillers. The tensile strength of biocomposites was increased by addition CNC and citric acid. The addition of CNC decreases the elongation at break but by addition of citric acid, the elongation at break was increased.

Observations of seasonal exchange in the Celtic Sea slope region from underwater gilders

NASA Astrophysics Data System (ADS)

Porter, Marie; Inall, Mark; Smeed, David; Palmer, Matthew; Dumont, Estelle; Aleynik, Dmitry

2015-04-01

Between June 2012 and January 2013, four underwater gliders, profiling to a maximum depth of 1000m, occupied a transect between 47.6°N, 10.3°W and 48.4°N, 9.3°W, perpendicular to the Celtic Sea continental slope. Due to the significant and well-documented internal tide activity in this region and the relatively slow through-water speed of gliders it is first demonstrated that the chosen sampling methodology minimised aliasing of the internal tide. Gliders were flown along a repeat transect and care was taken to ensure that each location was sampled at a different phase of the tide on repeat occupations. Through monthly averaging of the transect data, the effects of the internal tide are minimised and the lower frequency processes made visible. In this presentation we highlight the importance of the lower frequency variability in contributing to cross-slope exchange. Analysis of monthly averaged glider transect data suggests two distinct regimes; 1) Summer, June - October, when the surface water was temperature stratified and, 2) Winter, from October to January, when the seasonal thermocline was mixed down to below the depth of the shelf break (200 m). During the stratified summer months a well-defined shelf break salinity front limits the exchange of water between the ocean and the shelf, preventing the spread of the more saline, sub-surface ocean water (centred at ~150m) onto the shelf. Nevertheless, some cross-slope flow is identified during these months: an intermediate depth salinity minimum (centred at ~600m) is observed to upwell (from 600m to 200-300m) up the slope, sometimes continuing onto the shelf. As the stratification is eroded during the winter months, subsurface upwelling switches to downwelling, and the intermediate depth salinity minimum (~600m) retreats away from the slope region removing it as a potential source of oceanic water on the shelf. Downwelling near to the slope does however allow for an intrusion of the shallower high salinity water onto the shelf reducing the control of the shelf break salinity front, although it has not been ascertained whether this extends further onto the shelf than the shelf break region.

Production of Bacterial Cellulose by Gluconacetobacter hansenii Using Corn Steep Liquor As Nutrient Sources

PubMed Central

Costa, Andrea F. S.; Almeida, Fabíola C. G.; Vinhas, Glória M.; Sarubbo, Leonie A.

2017-01-01

Cellulose is mainly produced by plants, although many bacteria, especially those belonging to the genus Gluconacetobacter, produce a very peculiar form of cellulose with mechanical and structural properties that can be exploited in numerous applications. However, the production cost of bacterial cellulose (BC) is very high to the use of expensive culture media, poor yields, downstream processing, and operating costs. Thus, the purpose of this work was to evaluate the use of industrial residues as nutrients for the production of BC by Gluconacetobacter hansenii UCP1619. BC pellicles were synthesized using the Hestrin–Schramm (HS) medium and alternative media formulated with different carbon (sugarcane molasses and acetylated glucose) and nitrogen sources [yeast extract, peptone, and corn steep liquor (CSL)]. A jeans laundry was also tested. None of the tested sources (beside CSL) worked as carbon and nutrient substitute. The alternative medium formulated with 1.5% glucose and 2.5% CSL led to the highest yield in terms of dry and hydrated mass. The BC mass produced in the alternative culture medium corresponded to 73% of that achieved with the HS culture medium. The BC pellicles demonstrated a high concentration of microfibrils and nanofibrils forming a homogenous, compact, and three-dimensional structure. The biopolymer produced in the alternative medium had greater thermal stability, as degradation began at 240°C, while degradation of the biopolymer produced in the HS medium began at 195°C. Both biopolymers exhibited high crystallinity. The mechanical tensile test revealed the maximum breaking strength and the elongation of the break of hydrated and dry pellicles. The dry BC film supported up to 48 MPa of the breaking strength and exhibited greater than 96.98% stiffness in comparison with the hydrated film. The dry film supported up to 48 MPa of the breaking strength and exhibited greater than 96.98% stiffness in comparison with the hydrated film. The values obtained for the Young’s modulus in the mechanical tests in the hydrated samples indicated low values for the variable rigidity. The presence of water in the interior and between the nanofibers of the hydrated BC only favored the results for the elasticity, which was 56.37% higher when compared to the dry biomaterial. PMID:29089941

Breaking rocks made easy: subcritical processes and tectonic predesign

NASA Astrophysics Data System (ADS)

Voigtlaender, Anne; Krautblatter, Michael

2017-04-01

In geomorphic studies, to change in landforms, e.g. by rock slope failure, fluvial or glacial erosion, a threshold is commonly assumed, which is crossed either by an increase in external driving or a decrease of internal resisting forces, respectively. If the threshold is crossed, bedrock breaks and slope fails, rivers incise and glaciers plug and sew their bed. Here we put forward a focus on the decrease of the resisting forces, as an increase in the driving forces, to match the strength of bedrock, is not that likely. We suggest that the degradation of resisting forces of bedrock can be better explained by subcritical processes like creep, fatigue and stress corrosion interplaying with tectonic predesign. Both concepts, subcritical processes and tectonic predesign have been issued in the last century, but have not been widely accepted nor have their assumptions been explicitly stressed in recent case studies. Moreover both concepts profit especially on scale issues if merged. Subcritical crack growth, includes different mechanisms promoting fractures well below the ultimate strength. Single infinitesimal but irreversible damage and deformations are induced in the material over time. They interact with inherent microstructural flaws and low applied stresses, limiting local strength and macroscopic behavior of bedrock. This reissues the concept of tectonic predesigned, as proposed by A.E. Scheidegger, which not only encompasses structural features that determine the routing of drainage patterns and shear planes, e.g. joints, faults and foliations, but also the (neo)tectonic stress-field and the (in-situ) strain state of bedrocks and mountains. Combining subcritical processes and tectonic predesign we can better explain, why and where we see a dissected, eroded and geomorphic divers' landscape. In this conceptual framework actual magnitudes of the driving forces are accounted for and so is the nature of the bedrock material, to better understand the trajectories of the forms we study, and break rocks easily.

Ionic strength and DOC determinations from various freshwater sources to the San Francisco Bay

USGS Publications Warehouse

Hunter, Y.R.; Kuwabara, J.S.

1994-01-01

An exact estimation of dissolved organic carbon (DOC) within the salinity gradient of zinc and copper metals is significant in understanding the limit to which DOC could influence metal speciation. A low-temperature persulfate/oxygen/ultraviolet wet oxidation procedure was utilized for analyzing DOC samples adapted for ionic strength from major freshwater sources of the northern and southern regions of San Francisco Bay. The ionic strength of samples was modified with a chemically defined seawater medium up to 0.7M. Based on the results, a minimum effect of ionic strength on oxidation proficiency for DOC sources to the Bay over an ionic strength gradient of 0.0 to 0.7 M was observed. There was no major impacts of ionic strength on two Suwanee River fulvic acids. In general, the noted effects associated with ionic strength were smaller than the variances seen in the aquatic environment between high- and low-temperature methods.

High performance carbon fibers from very high molecular weight polyacrylonitrile precursors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, E. Ashley; Weisenberger, Matthew C.; Abdallah, Mohamed G.

In this study, carbon fibers are unique reinforcing agents for lightweight composite materials due to their outstanding mechanical properties and low density. Current technologies are capable of producing carbon fibers with 90-95% of the modulus of perfect graphite (~1025 GPa). However, these same carbon fibers possess less than 10% of the theoretical carbon fiber strength, estimated to be about 100 GPa.[1] Indeed, attempts to increase carbon fiber rigidity results in lower breaking strength. To develop advanced carbon fibers with both very high strength and modulus demands a new manufacturing methodology. Here, we report a method of manufacturing high strength, verymore » high modulus carbon fibers from a very high molecular weight (VHMW) polyacrylonitrile (PAN) precursor without the use of nanomaterial additives such as nucleating or structure-templating agents, as have been used by others.[2,3]« less

Microstructural and Mechanical Properties of Hot Roll Bonded Titanium Alloy/Low Carbon Steel Plate

NASA Astrophysics Data System (ADS)

Yu, Chao; Qi, Zi-chen; Yu, Hui; Xu, Cheng; Xiao, Hong

2018-03-01

In this paper, a titanium alloy and low carbon steel were bonded via hot rolling in a vacuum, and the effect of roll bonding temperature and reduction ratio on the microstructural and mechanical properties of the plate was studied. When the bonding temperature was between 850 and 1050 °C, the shear strength of the interface increased with an increasing reduction ratio from 18 to 70%. At a bonding temperature of 950 °C and at a rolling reduction ratio of 70%, the best bonding strength was obtained, and a shear fracture occurred on the low carbon steel matrix. At 1050 °C, brittle compounds, i.e., TiC, FeTi, and Fe2Ti, formed at the interface, which decreased the bonding strength. The large reduction ratio can break up compounds at the interface and extrude fresh metal for bonding, thereby increasing the bonding strength.

Indirect and direct tensile behavior of Devonian oil shales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chong, K.P.; Chen, J.L.; Dana, G.F.

1984-03-01

Ultimate indirect tensile strengths of Devonian oil shales across the bedding planes is a mechanical property parameter important to predicting how oil shale will break. This is particularly important to in-situ fragmentation. The Split Cylinder Test was used to determine the indirect tensile strengths between the bedding planes. Test specimens, cored perpendicular to the bedding planes, representing oil shales of different oil yields taken from Silver Point Quad in DeKalb County, Tennessee and Friendship in Scioto County, Ohio, were subjected to the Split Cylinder Test. Linear regression equations relating ultimate tensile strength across the bedding planes to volume percent ofmore » organic matter in the rock were developed from the test data. In addition, direct tensile strengths were obtained between the bedding planes for the Tennessee oil shales. This property is important for the design of horizontal fractures in oil shales. Typical results were presented.« less

Contribution of Hydrogen Bonds to Paper Strength Properties.

PubMed

Przybysz, Piotr; Dubowik, Marcin; Kucner, Marta Anna; Przybysz, Kazimierz; Przybysz Buzała, Kamila

2016-01-01

The objective of this work was to investigate the influence of hydrogen bonds between fibres on static and dynamic strength properties of paper. A commercial bleached pinewood kraft pulp was soaked in water, refined in a PFI, and used to form paper webs in different solvents, such as water, methanol, ethanol, n-propanol and n-butanol, to determine the effect of their dipole moment on static and dynamic strength properties of resulting paper sheets. Paper which was formed in water, being the solvent of the highest dipole moment among the tested ones, showed the highest breaking length and tear resistance. When paper webs were formed in n-butanol, which was the least polar among the solvents, these parameters were reduced by around 75%. These results provide evidence of the importance of water in paper web formation and strong impact of hydrogen bonds between fibres on strength properties of paper.

Contribution of Hydrogen Bonds to Paper Strength Properties

PubMed Central

Przybysz, Piotr; Dubowik, Marcin; Kucner, Marta Anna; Przybysz, Kazimierz; Przybysz Buzała, Kamila

2016-01-01

The objective of this work was to investigate the influence of hydrogen bonds between fibres on static and dynamic strength properties of paper. A commercial bleached pinewood kraft pulp was soaked in water, refined in a PFI, and used to form paper webs in different solvents, such as water, methanol, ethanol, n-propanol and n-butanol, to determine the effect of their dipole moment on static and dynamic strength properties of resulting paper sheets. Paper which was formed in water, being the solvent of the highest dipole moment among the tested ones, showed the highest breaking length and tear resistance. When paper webs were formed in n-butanol, which was the least polar among the solvents, these parameters were reduced by around 75%. These results provide evidence of the importance of water in paper web formation and strong impact of hydrogen bonds between fibres on strength properties of paper. PMID:27228172

High performance carbon fibers from very high molecular weight polyacrylonitrile precursors

DOE PAGES

Morris, E. Ashley; Weisenberger, Matthew C.; Abdallah, Mohamed G.; ...

2016-02-02

In this study, carbon fibers are unique reinforcing agents for lightweight composite materials due to their outstanding mechanical properties and low density. Current technologies are capable of producing carbon fibers with 90-95% of the modulus of perfect graphite (~1025 GPa). However, these same carbon fibers possess less than 10% of the theoretical carbon fiber strength, estimated to be about 100 GPa.[1] Indeed, attempts to increase carbon fiber rigidity results in lower breaking strength. To develop advanced carbon fibers with both very high strength and modulus demands a new manufacturing methodology. Here, we report a method of manufacturing high strength, verymore » high modulus carbon fibers from a very high molecular weight (VHMW) polyacrylonitrile (PAN) precursor without the use of nanomaterial additives such as nucleating or structure-templating agents, as have been used by others.[2,3]« less

Experimental and analytical investigation of the fracture processes of boron/aluminum laminates containing notches

NASA Technical Reports Server (NTRS)

Johnson, W. S.; Bigelow, C. A.; Bahei-El-din, Y. A.

1983-01-01

Experimental results for five laminate orientations of boron/aluminum composites containing either circular holes or crack-like slits are presented. Specimen stress-strain behavior, stress at first fiber failure, and ultimate strength were determined. Radiographs were used to monitor the fracture process. The specimens were analyzed with a three-dimensional elastic-elastic finite-element model. The first fiber failures in notched specimens with laminate orientation occurred at or very near the specimen ultimate strength. For notched unidirectional specimens, the first fiber failure occurred at approximately one-half of the specimen ultimate strength. Acoustic emission events correlated with fiber breaks in unidirectional composites, but did not for other laminates. Circular holes and crack-like slits of the same characteristic length were found to produce approximately the same strength reduction. The predicted stress-strain responses and stress at first fiber failure compared very well with test data for laminates containing 0 deg fibers.

Automated predesign of aircraft

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.; Kruse, G. S.; Tanner, C. J.; Wilson, P. J.

1978-01-01

Program uses multistation structural-synthesis to size and design box-beam structures for transport aircraft. Program optimizes static strength and scales up to satisfy fatigue and fracture criteria. It has multimaterial capability and library of materials properties, including advanced composites. Program can be used to evaluate impact on weight of variables such as materials, types of construction, structural configurations, minimum gage limits, applied loads, fatigue lives, crack-growth lives, initial crack sizes, and residual strengths.

Extended Bose-Hubbard model with dipolar and contact interactions

NASA Astrophysics Data System (ADS)

Biedroń, Krzysztof; Łącki, Mateusz; Zakrzewski, Jakub

2018-06-01

We study the phase diagram of the one-dimensional boson gas trapped inside an optical lattice with contact and dipolar interaction, taking into account next-nearest terms for both tunneling and interaction. Using the density-matrix renormalization group, we calculate how the locations of phase transitions change with increasing dipolar interaction strength for average density ρ =1 . Furthermore, we show the emergence of pair-correlated phases for a large dipolar interaction strength and ρ ≥2 , including a supersolid phase with an incommensurate density wave ordering manifesting the corresponding spontaneous breaking of the translational symmetry.

Nonlinear mechanics of thermoreversibly associating dendrimer glasses

NASA Astrophysics Data System (ADS)

Srikanth, Arvind; Hoy, Robert S.; Rinderspacher, Berend C.; Andzelm, Jan W.

2013-10-01

We model the mechanics of associating trivalent dendrimer network glasses with a focus on their energy dissipation properties. Various combinations of sticky bond (SB) strength and kinetics are employed. The toughness (work to fracture) of these systems displays a surprising deformation-protocol dependence; different association parameters optimize different properties. In particular, “strong, slow” SBs optimize strength, while “weak, fast” SBs optimize ductility via self-healing during deformation. We relate these observations to breaking, reformation, and partner switching of SBs during deformation. These studies point the way to creating associating-polymer network glasses with tailorable mechanical properties.

The Effect of Multi Wall Carbon Nanotubes on Some Physical Properties of Epoxy Matrix

NASA Astrophysics Data System (ADS)

Al-Saadi, Tagreed M.; hammed Aleabi, Suad; Al-Obodi, Entisar E.; Abdul-Jabbar Abbas, Hadeel

2018-05-01

This research involves using epoxy resin as a matrix for making a composite material, while the multi wall carbon nanotubes (MWNCTs) is used as a reinforcing material with different fractions (0.0,0.02, 0.04, 0.06) of the matrix weight. The mechanical ( hardness ), electrical ( dielectric constant, dielectric loss factor, dielectric strength, electrical conductivity ), and thermal properties (thermal conductivity ) were studied. The results showed the increase of hardness, thermal conductivity, electrical conductivity and break down strength with the increase of MWCNT concentration, but the behavior of dielectric loss factor and dielectric constant is opposite that.

Development of UHPC Mixtures Utilizing Natural and Industrial Waste Materials as Partial Replacements of Silica Fume and Sand

PubMed Central

2014-01-01

In the exploratory study presented in this paper, an attempt was made to develop different mixtures of ultrahigh performance concrete (UHPC) using various locally available natural and industrial waste materials as partial replacements of silica fume and sand. Materials such as natural pozzolana (NP), fly ash (FA), limestone powder (LSP), cement kiln dust (CKD), and pulverized steel slag (PSS), all of which are abundantly available in Saudi Arabia at little or no cost, were employed in the development of the UHPC mixtures. A base mixture of UHPC without replacement of silica fume or sand was selected and a total of 24 trial mixtures of UHPC were prepared using different percentages of NP, FA, LSP, CKD, and PSS, partially replacing the silica fume and sand. Flow and 28-d compressive strength of each UHPC mixture were determined to finally select those mixtures, which satisfied the minimum flow and strength criteria of UHPC. The test results showed that the utilization of NP, FA, LSP, CKD, and PSS in production of UHPC is possible with acceptable flow and strength. A total of 10 UHPC mixtures were identified with flow and strength equal to or more than the minimum required. PMID:25197709

Structural and mechanical properties of glassy water in nanoscale confinement.

PubMed

Lombardo, Thomas G; Giovambattista, Nicolás; Debenedetti, Pablo G

2009-01-01

We investigate the structure and mechanical properties of glassy water confined between silica-based surfaces with continuously tunable hydrophobicity and hydrophilicity by computing and analyzing minimum energy, mechanically stable configurations (inherent structures). The structured silica substrate imposes long-range order on the first layer of water molecules under hydrophobic confinement at high density (p > or = 1.0 g cm(-3)). This proximal layer is also structured in hydrophilic confinement at very low density (p approximately 0.4 g cm(-3)). The ordering of water next to the hydrophobic surface greatly enhances the mechanical strength of thin films (0.8 nm). This leads to a substantial stress anisotropy; the transverse strength of the film exceeds the normal strength by 500 MPa. The large transverse strength results in a minimum in the equation of state of the energy landscape that does not correspond to a mechanical instability, but represents disruption of the ordered layer of water next to the wall. In addition, we find that the mode of mechanical failure is dependent on the type of confinement. Under large lateral strain, water confined by hydrophilic surfaces preferentially forms voids in the middle of the film and fails cohesively. In contrast, water under hydrophobic confinement tends to form voids near the walls and fails by loss of adhesion.

ZERODUR: bending strength data for etched surfaces

NASA Astrophysics Data System (ADS)

Hartmann, Peter; Leys, Antoine; Carré, Antoine; Kerz, Franca; Westerhoff, Thomas

2014-07-01

In a continuous effort since 2007 a considerable amount of new data and information has been gathered on the bending strength of the extremely low thermal expansion glass ceramic ZERODUR®. By fitting a three parameter Weibull distribution to the data it could be shown that for homogenously ground surfaces minimum breakage stresses exist lying much higher than the previously applied design limits. In order to achieve even higher allowable stress values diamond grain ground surfaces have been acid etched, a procedure widely accepted as strength increasing measure. If surfaces are etched taking off layers with thickness which are comparable to the maximum micro crack depth of the preceding grinding process they also show statistical distributions compatible with a three parameter Weibull distribution. SCHOTT has performed additional measurement series with etch solutions with variable composition testing the applicability of this distribution and the possibility to achieve further increase of the minimum breakage stress. For long term loading applications strength change with time and environmental media are important. The parameter needed for prediction calculations which is combining these influences is the stress corrosion constant. Results from the past differ significantly from each other. On the basis of new investigations better information will be provided for choosing the best value for the given application conditions.

Improving UV Resistance of High Performance Fibers

NASA Astrophysics Data System (ADS)

Hassanin, Ahmed

High performance fibers are characterized by their superior properties compared to the traditional textile fibers. High strength fibers have high modules, high strength to weight ratio, high chemical resistance, and usually high temperature resistance. It is used in application where superior properties are needed such as bulletproof vests, ropes and cables, cut resistant products, load tendons for giant scientific balloons, fishing rods, tennis racket strings, parachute cords, adhesives and sealants, protective apparel and tire cords. Unfortunately, Ultraviolet (UV) radiation causes serious degradation to the most of high performance fibers. UV lights, either natural or artificial, cause organic compounds to decompose and degrade, because the energy of the photons of UV light is high enough to break chemical bonds causing chain scission. This work is aiming at achieving maximum protection of high performance fibers using sheathing approaches. The sheaths proposed are of lightweight to maintain the advantage of the high performance fiber that is the high strength to weight ratio. This study involves developing three different types of sheathing. The product of interest that need be protected from UV is braid from PBO. First approach is extruding a sheath from Low Density Polyethylene (LDPE) loaded with different rutile TiO2 % nanoparticles around the braid from the PBO. The results of this approach showed that LDPE sheath loaded with 10% TiO2 by weight achieved the highest protection compare to 0% and 5% TiO2. The protection here is judged by strength loss of PBO. This trend noticed in different weathering environments, where the sheathed samples were exposed to UV-VIS radiations in different weatheromter equipments as well as exposure to high altitude environment using NASA BRDL balloon. The second approach is focusing in developing a protective porous membrane from polyurethane loaded with rutile TiO2 nanoparticles. Membrane from polyurethane loaded with 4% rutile TiO2 nanoparticles showed excellent protection of braid from PBO. Only 7.5% strength loss was observed. To optimize the degree of protection of the sheath loaded with UV blocker particles, computational models were developed to optimize the protective layer thickness/weight and the amount of UV particles that provide the maximum protection with lightest weight of the protective layer and minimum amount of UV particles. The simulated results were found to be higher that the experimental results due to the tendency of nanoparticles to be agglomerated in real experiments. The third approach to achieve a maximum protection with the minimum weight added is constructing a sleeve from SpectraRTM (Ultra High Molecular Weight Polyethylene (UHMWPE) high performance fiber), which is known to resist UV, woven fabric. Covering the braid from PBO fiber with Spectra RTM woven fabric provide hybrid structure with two compatible components that can share the load and thus maintain the high strength to weight ratio. Although the SpectraRTM fabric had maximum cover factor, 20 % of visible light and about 15 % of UV were able to penetrate the fabric. This transmittance of UV-VIS light negatively affected the protection performance of the SpectraRTM woven fabric layer. It is thought that SpectraRTM fabric be coated with a thin layer (mentioned earlier) containing UV blocker for additional protection while maintain strength contribution to the hybrid structure. To maximize the strength to weight ratio of the hybrid structure (with core from PBO braid and sheath from SpectraRTM woven fabric) an established finite element model was utilized. The theoretical results using the finite element theory indicated that by controlling the bending rigidity of the filling yarn of the SpectraRTM fabric, the extension at peak load of woven fabric in warp direction (loading direction) could be controlled to match the braid extension at peak load. The match in the extension at peak load of the two components of the hybrid structure allowed the maximum strength to weight ratio. Thus, the SpectraRTM woven layer could achieve both the protection from UV and the load share in the hybrid structure.

Evolution of the pygmy dipole resonance in Sn isotopes

NASA Astrophysics Data System (ADS)

Toft, H. K.; Larsen, A. C.; Bürger, A.; Guttormsen, M.; Görgen, A.; Nyhus, H. T.; Renstrøm, T.; Siem, S.; Tveten, G. M.; Voinov, A.

2011-04-01

Nuclear level density and γ-ray strength functions of Sn121,122 below the neutron separation energy are extracted with the Oslo method using the (He3,He3'γ) and (He3,αγ) reactions. The level densities of Sn121,122 display steplike structures, interpreted as signatures of neutron pair breaking. An enhancement in both strength functions, compared to standard models for radiative strength, is observed in our measurements for Eγ≳5.2 MeV. This enhancement is compatible with pygmy resonances centered at ≈8.4(1) and ≈8.6(2) MeV, respectively, and with integrated strengths corresponding to ≈1.8-5+1% of the classical Thomas-Reiche-Kuhn sum rule. Similar resonances were also seen in Sn116-119. Experimental neutron-capture cross reactions are well reproduced by our pygmy resonance predictions, while standard strength models are less successful. The evolution as a function of neutron number of the pygmy resonance in Sn116-122 is described as a clear increase of centroid energy from 8.0(1) to 8.6(2) MeV, but with no observable difference in integrated strengths.

The breaking load method - Results and statistical modification from the ASTM interlaboratory test program

NASA Technical Reports Server (NTRS)

Colvin, E. L.; Emptage, M. R.

1992-01-01

The breaking load test provides quantitative stress corrosion cracking data by determining the residual strength of tension specimens that have been exposed to corrosive environments. Eight laboratories have participated in a cooperative test program under the auspices of ASTM Committee G-1 to evaluate the new test method. All eight laboratories were able to distinguish between three tempers of aluminum alloy 7075. The statistical analysis procedures that were used in the test program do not work well in all situations. An alternative procedure using Box-Cox transformations shows a great deal of promise. An ASTM standard method has been drafted which incorporates the Box-Cox procedure.

FAST TRACK COMMUNICATION: Criticality-induced universality in ratchets

NASA Astrophysics Data System (ADS)

Chacón, Ricardo

2010-08-01

Conclusive mathematical arguments are presented supporting the ratchet conjecture (Chacón 2007 J. Phys. A: Math. Theor. 40 F413), i.e. the existence of a universal force waveform which optimally enhances directed transport by symmetry breaking. Specifically, such a particular waveform is shown to be unique for both temporal and spatial biharmonic forces, and general (non-perturbative) laws providing the dependence of the strength of directed transport on the force parameters are deduced for these forces. The theory explains previous results for a great diversity of systems subjected to such biharmonic forces and provides a universal quantitative criterion to optimize any application of the ratchet effect induced by symmetry breaking of temporal and spatial biharmonic forces.

Hanford's Simulated Low Activity Waste Cast Stone Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Young

2013-08-20

Cast Stone is undergoing evaluation as the supplemental treatment technology for Hanford’s (Washington) high activity waste (HAW) and low activity waste (LAW). This report will only cover the LAW Cast Stone. The programs used for this simulated Cast Stone were gradient density change, compressive strength, and salt waste form phase identification. Gradient density changes show a favorable outcome by showing uniformity even though it was hypothesized differently. Compressive strength exceeded the minimum strength required by Hanford and greater compressive strength increase seen between the uses of different salt solution The salt waste form phase is still an ongoing process asmore » this time and could not be concluded.« less

Lorentz violation with a universal minimum speed as foundation of de Sitter relativity

NASA Astrophysics Data System (ADS)

Cruz, Cláudio Nassif; Dos Santos, Rodrigo Francisco; Amaro de Faria, A. C.

We aim to investigate the theory of Lorentz violation with an invariant minimum speed called Symmetrical Special Relativity (SSR) from the viewpoint of its metric. Thus, we should explore the nature of SSR-metric in order to understand the origin of the conformal factor that appears in the metric by deforming Minkowski metric by means of an invariant minimum speed that breaks down Lorentz symmetry. So, we are able to realize that there is a similarity between SSR and a new space with variable negative curvature ( -∞ < ℛ < 0) connected to a set of infinite cosmological constants (0 < Λ < ∞), working like an extended de Sitter (dS) relativity, so that such extended dS-relativity has curvature and cosmological “constant” varying in time. We obtain a scenario that is more similar to dS-relativity given in the approximation of a slightly negative curvature for representing the current universe having a tiny cosmological constant. Finally, we show that the invariant minimum speed provides the foundation for understanding the kinematics origin of the extra dimension considered in dS-relativity in order to represent the dS-length.

Estimation of Confined Peak Strength of Crack-Damaged Rocks

NASA Astrophysics Data System (ADS)

Bahrani, Navid; Kaiser, Peter K.

2017-02-01

It is known that the unconfined compressive strength of rock decreases with increasing density of geological features such as micro-cracks, fractures, and veins both at the laboratory specimen and rock block scales. This article deals with the confined peak strength of laboratory-scale rock specimens containing grain-scale strength dominating features such as micro-cracks. A grain-based distinct element model, whereby the rock is simulated with grains that are allowed to deform and break, is used to investigate the influence of the density of cracks on the rock strength under unconfined and confined conditions. A grain-based specimen calibrated to the unconfined and confined strengths of intact and heat-treated Wombeyan marble is used to simulate rock specimens with varying crack densities. It is demonstrated how such cracks affect the peak strength, stress-strain curve and failure mode with increasing confinement. The results of numerical simulations in terms of unconfined and confined peak strengths are used to develop semi-empirical relations that relate the difference in strength between the intact and crack-damaged rocks to the confining pressure. It is shown how these relations can be used to estimate the confined peak strength of a rock with micro-cracks when the unconfined and confined strengths of the intact rock and the unconfined strength of the crack-damaged rock are known. This approach for estimating the confined strength of crack-damaged rock specimens, called strength degradation approach, is then verified by application to published laboratory triaxial test data.

Evaluation of alternative model selection criteria in the analysis of unimodal response curves using CART

USGS Publications Warehouse

Ribic, C.A.; Miller, T.W.

1998-01-01

We investigated CART performance with a unimodal response curve for one continuous response and four continuous explanatory variables, where two variables were important (ie directly related to the response) and the other two were not. We explored performance under three relationship strengths and two explanatory variable conditions: equal importance and one variable four times as important as the other. We compared CART variable selection performance using three tree-selection rules ('minimum risk', 'minimum risk complexity', 'one standard error') to stepwise polynomial ordinary least squares (OLS) under four sample size conditions. The one-standard-error and minimum-risk-complexity methods performed about as well as stepwise OLS with large sample sizes when the relationship was strong. With weaker relationships, equally important explanatory variables and larger sample sizes, the one-standard-error and minimum-risk-complexity rules performed better than stepwise OLS. With weaker relationships and explanatory variables of unequal importance, tree-structured methods did not perform as well as stepwise OLS. Comparing performance within tree-structured methods, with a strong relationship and equally important explanatory variables, the one-standard-error-rule was more likely to choose the correct model than were the other tree-selection rules 1) with weaker relationships and equally important explanatory variables; and 2) under all relationship strengths when explanatory variables were of unequal importance and sample sizes were lower.

Chromospheric Signatures of the Subdued Cycle 23/24 Solar Minimum in Microwaves

NASA Technical Reports Server (NTRS)

Yashiro, S.; Makela, P.; Shibasaki, K.; Hathaway, D.

2011-01-01

Coronal holes appear brighter than the quiet Sun in microwave images, with a brightness enhancement of 500 to 2000 K. The brightness enhancement corresponds to the upper chromosphere, where the plasma temperature is about 10000 K. We constructed a microwave butterfly diagram using the synoptic images obtained by the Nobeyama radio-heliograph (NoRH) showing the evolution of the polar and low latitude brightness temperature. While the polar brightness reveals the chromospheric conditions, the low latitude brightness is attributed to active regions in the corona. When we compared the microwave butterfly diagram with the magnetic butterfly diagram, we found a good correlation between the microwave brightness enhancement and the polar field strength. The microwave butterfly diagram covers part of solar cycle 22, whole of cycle 23, and part of cycle 24, thus enabling comparison between the cycle 23/24 and cycle 22/23 minima. The microwave brightness during the cycle 23/24 minimum was found to be lower than that during the cycle 22/23 minimum by approx.250 K. The reduced brightness temperature is consistent with the reduced polar field strength during the cycle 23/24 minimum seen in the magnetic butterfly diagram. We suggest that the microwave brightness at the solar poles is a good indicator of the speed of the solar wind sampled by Ulysses at high latitudes.

33 CFR 165.803 - Mississippi River-regulated navigation area.

Code of Federal Regulations, 2013 CFR

2013-07-01

... breaking strength of three parts of 7/8 inch diameter wire rope; or (3) Fixed rigging that is at least... end of the tier is secured to at least one mooring device. (3) Each wire rope used between the... inch diameter wire rope. (4) Each wire rope used between the downstream end of a barge and a mooring...

33 CFR 165.803 - Mississippi River-regulated navigation area.

Code of Federal Regulations, 2012 CFR

2012-07-01

... breaking strength of three parts of 7/8 inch diameter wire rope; or (3) Fixed rigging that is at least... end of the tier is secured to at least one mooring device. (3) Each wire rope used between the... inch diameter wire rope. (4) Each wire rope used between the downstream end of a barge and a mooring...

33 CFR 165.803 - Mississippi River-regulated navigation area.

Code of Federal Regulations, 2011 CFR

2011-07-01

... breaking strength of three parts of 7/8 inch diameter wire rope; or (3) Fixed rigging that is at least... end of the tier is secured to at least one mooring device. (3) Each wire rope used between the... inch diameter wire rope. (4) Each wire rope used between the downstream end of a barge and a mooring...

33 CFR 165.803 - Mississippi River-regulated navigation area.

Code of Federal Regulations, 2014 CFR

2014-07-01

... breaking strength of three parts of 7/8 inch diameter wire rope; or (3) Fixed rigging that is at least... end of the tier is secured to at least one mooring device. (3) Each wire rope used between the... inch diameter wire rope. (4) Each wire rope used between the downstream end of a barge and a mooring...

Black Families and the Struggle for Survival.

ERIC Educational Resources Information Center

Billingsley, Andrew; And Others

Breaking away from those who see the structure of family life in the black community as pathological, this study wishes to assist a lay audience in identifying the strengths of black families. The book provides both insights and resources for engaging churches and black families in the common task of enhancing black family life. Where the church's…

How to Break through Techno-Shock and Build Multi-Media Units.

ERIC Educational Resources Information Center

Sutz, Rachel; Warren, Maria W.; Williams, Holly

1998-01-01

Describes how three teachers learned about using Hyperstudio (presentation software), constructed a Web page, and created an original film as part of a unit on Florida writers. Recommends three major strategies for learning a new technology: choose the literary works, then the technology; build on your strengths; and learn to talk to the…

Flexural strength of proof-tested and neutron-irradiated silicon carbide

NASA Astrophysics Data System (ADS)

Price, R. J.; Hopkins, G. R.

1982-08-01

Proof testing before service is a valuable method for ensuring the reliability of ceramic structures. Silicon carbide has been proposed as a very low activation first-wall and blanket structural material for fusion devices, where it would experience a high flux of fast neutrons. Strips of three types of silicon carbide were loaded in four-point bending to a stress sufficient to break about a third of the specimens. Groups of 16 survivors were irradiated to 2 × 10 26n/ m2 ( E>0.05 MeV) at 740°C and bend tested to failure. The strength distribution of chemically vapor-deposited silicon carbide (Texas Instruments) was virtually unchanged by irradiation. The mean strength of sintered silicon carbide (Carborundum Alpha) was reduced 34% by irradiation, while the Weibull modulus and the truncated strength distribution characteristic of proof-tested material were retained. Irradiation reduced the mean strength of reaction-bonded silicon carbide (Norton NC-430) by 58%, and the spread in strength values was increased. We conclude that for the chemically vapor-deposited and the sintered silicon carbide the benefits of proof testing to eliminate low strength material are retained after high neutron exposures.

The minimum or natural rate of flow and droplet size ejected by Taylor cone-jets: physical symmetries and scaling laws

NASA Astrophysics Data System (ADS)

Gañán-Calvo, A. M.; Rebollo-Muñoz, N.; Montanero, J. M.

2013-03-01

We aim to establish the scaling laws for both the minimum rate of flow attainable in the steady cone-jet mode of electrospray, and the size of the resulting droplets in that limit. Use is made of a small body of literature on Taylor cone-jets reporting precise measurements of the transported electric current and droplet size as a function of the liquid properties and flow rate. The projection of the data onto an appropriate non-dimensional parameter space maps a region bounded by the minimum rate of flow attainable in the steady state. To explain these experimental results, we propose a theoretical model based on the generalized concept of physical symmetry, stemming from the system time invariance (steadiness). A group of symmetries rising at the cone-to-jet geometrical transition determines the scaling for the minimum flow rate and related variables. If the flow rate is decreased below that minimum value, those symmetries break down, which leads to dripping. We find that the system exhibits two instability mechanisms depending on the nature of the forces arising against the flow: one dominated by viscosity and the other by the liquid polarity. In the former case, full charge relaxation is guaranteed down to the minimum flow rate, while in the latter the instability condition becomes equivalent to the symmetry breakdown by charge relaxation or separation. When cone-jets are formed without artificially imposing a flow rate, a microjet is issued quasi-steadily. The flow rate naturally ejected this way coincides with the minimum flow rate studied here. This natural flow rate determines the minimum droplet size that can be steadily produced by any electrohydrodynamic means for a given set of liquid properties.

Imaging the Tear Film: A Comparison Between the Subjective Keeler Tearscope-Plus™ and the Objective Oculus® Keratograph 5M and LipiView® Interferometer.

PubMed

Markoulli, Maria; Duong, Tran Bao; Lin, Margaret; Papas, Eric

2018-02-01

To compare non-invasive break-up time (NIBUT) when measured with the Tearscope-Plus™ and the Oculus® Keratograph 5M, and to compare lipid layer thicknesses (LLT) when measured with the Tearscope-Plus™ and the LipiView®. This study also set out to establish the repeatability of these methods. The following measurements were taken from both eyes of 24 participants on two occasions: non-invasive keratograph break-up time using the Oculus® (NIKBUT-1 and NIKBUT-average), NIBUT using the Tearscope-Plus™, and LLT using the LipiView® (minimum, maximum, and average) and Tearscope-Plus™. The Tearscope-Plus™ grades were converted to nanometers. There were no significant differences between eyes (Tearscope-Plus™ NIBUT: p = 0.52; NIKBUT-1: p = 0.052; NIKBUT-average: p = 0.73; Tearscope-Plus™ LLT: p = 0.13; LipiView® average, maximum, or minimum: p = 0.68, 0.39 and 0.50, respectively) or days (Tearscope-Plus™ NIBUT: p = 0.32; NIKBUT-1: p = 0.65; NIKBUT-average: p = 0.54; Tearscope-Plus™ LLT: p = 0.26; LipiView® average, maximum, or minimum: p = 0.20, 0.09, and 0.10, respectively). LLT was significantly greater with the Tearscope-Plus™ (80.4 ± 34.0 nm) compared with the LipiView® average (56.3 ± 16.1 nm, p = 0.007), minimum (50.1 ± 15.8 nm, p < 0.001) but not maximum (67.2 ± 19.6 nm, p = 0.55). NIBUT was significantly greater with the Tearscope-Plus™ (15.9 ± 10.7 seconds) compared to the NIKBUT-1 (8.2 ± 3.5 seconds, p = 0.006) but not NIKBUT-average (10.9 ± 3.9 seconds, p = 0.08). The Tearscope-Plus™ is not interchangeable with either the Oculus® K5M measurement of tear stability (NIKBUT-1) or the LipiView® maximum and minimum lipid thickness.

Atmospheric Transport and Mixing linked to Rossby Wave Breaking in GFDL Dynamical Core

NASA Astrophysics Data System (ADS)

Liu, C.; Barnes, E. A.

2015-12-01

Atmospheric transport and mixing plays an important role in the global energy balance and the distribution of health-related chemical constituents. Previous studies suggest a close linkage between large-scale transport and Rossby wave breaking (RWB). In this work, we use the GFDL spectral dynamical core to investigate this relationship and study the response of RWB-related transport in different climate scenarios. In a standard control run, we quantify the contribution of RWB to the total transport and mixing of an idealized tracer. In addition, we divide the contribution further into the two types of RWB - anticyclonic wave breaking (AWB) and cyclonic wave breaking (CWB) -- and contrast their efficiency at transport and mixing. Our results are compared to a previous study in which the transport ability of the two types of RWB is studied for individual baroclinic wave life-cycles. In a series of sensitivity runs, we study the response of RWB-related transport and mixing to various states of the jet streams. The responses of the mean strength, frequency, and the efficiency of RWB-related transport are documented and the implications for the transport and mixing in a warmer climate are discussed.

Thermalization and light cones in a model with weak integrability breaking

DOE PAGES

Bertini, Bruno; Essler, Fabian H. L.; Groha, Stefan; ...

2016-12-09

Here, we employ equation-of-motion techniques to study the nonequilibrium dynamics in a lattice model of weakly interacting spinless fermions. Our model provides a simple setting for analyzing the effects of weak integrability-breaking perturbations on the time evolution after a quantum quench. We establish the accuracy of the method by comparing results at short and intermediate times to time-dependent density matrix renormalization group computations. For sufficiently weak integrability-breaking interactions we always observe prethermalization plateaus, where local observables relax to nonthermal values at intermediate time scales. At later times a crossover towards thermal behavior sets in. We determine the associated time scale,more » which depends on the initial state, the band structure of the noninteracting theory, and the strength of the integrability-breaking perturbation. Our method allows us to analyze in some detail the spreading of correlations and in particular the structure of the associated light cones in our model. We find that the interior and exterior of the light cone are separated by an intermediate region, the temporal width of which appears to scale with a universal power law t 1/3.« less

Calcium requirements of growing rats based on bone mass, structure, or biomechanical strength are similar.

PubMed

Hunt, Janet R; Hunt, Curtiss D; Zito, Carol Ann; Idso, Joseph P; Johnson, LuAnn K

2008-08-01

Although calcium (Ca) supplementation increases bone density, the increase is small and the effect on bone strength and fracture risk is uncertain. To investigate if bone mass, morphology, and biomechanical properties are affected by deficient to copious dietary Ca concentrations, the long bones (tibia and femur) of growing female Sprague-Dawley rats (8/group) were assessed after 13 wk of consuming 1, 2, 3, 4, 5, 6, or 7 g Ca/kg of a modified AIN-93G diet. Dietary phosphorous (P) and vitamin D remained constant at recommended concentrations. The assessment included mineralization, density, biomechanical properties of breaking by a 3-point flexure test, and morphological properties by microcomputed topography scanning of trabecular bone of the proximal tibia metaphysis. Dietary treatment did not affect food intake, weight gain, renal and muscle Ca concentrations, and bone hydroxyproline. All bone parameters measured were significantly impaired by Ca deficiency in rats fed the diet containing 1 g Ca/kg. Modest impairments occurred with some parameters (bone density, biomechanical bending moment, modulus of elasticity, and stress) in rats fed 2 g Ca/kg, but all parameters stabilized between 2 and 3 g/kg diet, with no differences between 3 and 7 g/kg. The results suggest that a threshold response in bone Ca retention or bone mass at approximately 2.5 g Ca/kg diet is associated with similar threshold responses in bone breaking strength and related biomechanics as well as trabecular structural properties. There was no evidence of a relative P deficiency or of improved or impaired bone strength and structure as Ca intakes increased beyond those needed to maximize bone density.

Effects of autoclave sterilization on properties of dental rubber dam as related to its use as barrier membrane in guided tissue regeneration.

PubMed

Apinhasmit, Wandee; Limsombutanon, Somchai; Swasdison, Somporn; Suppipat, Nophadol

2003-10-01

Dental rubber dams (RDs) were used as barrier membranes in guided tissue regeneration for the treatment of periodontal intraosseous defects with acceptable clinical results. The aim of the present study was to investigate the effects of autoclave sterilization on properties of RD as related to its use as a barrier membrane in guided tissue regeneration. RDs were sterilized by either an autoclave, gamma irradiation, or chemical agents and then co-cultured with human gingival fibroblasts. The cell responses to sterilized RDs were investigated by inverted phase contrast microscopy, scanning electron microscopy (SEM) and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) technique. The surface alterations of the autoclaved RDs were observed under SEM. The tensile strength, tear strength and elongation at break of the autoclaved RDs were tested by a universal testing machine. The results from cell culture, microscopic and MTT studies showed that RDs sterilized by autoclave and gamma irradiation did not deteriorate gingival fibroblasts and provided surfaces suitable for cell attachment, whereas chemical-sterilized RDs were toxic to these cells. Ultrastructurally, surface changes from the non-autoclaved RDs, including some melted areas, small pores and folds were observed on the autoclaved RD surface. The tensile strength and tear strength of the autoclaved RDs were significantly lower than those of the non-autoclaved RDs (p = 0.042, p < 0.001, respectively). In contrast, the elongation at break of the autoclaved RDs was higher than that of the non-autoclaved RDs (p < 0.001). These results suggest that the autoclave sterilization deteriorated the physical properties of RDs even though they seemed to be compatible to the cultured human cells. Therefore, the sterilization method should be taken into consideration when RDs are utilized as barrier membranes.

Catharanthus roseus flower extract has wound-healing activity in Sprague Dawley rats

PubMed Central

Nayak, BS; Pinto Pereira, Lexley M

2006-01-01

Background Catharanthus roseus L (C. roseus) has been used to treat a wide assortment of diseases including diabetes. The objective of our study was to evaluate the antimicrobial and wound healing activity of the flower extract of Catharanthus in rats. Methods Wound healing activity was determined in rats, after administration (100 mg kg-1 day-1) of the ethanol extract of C. roseus flower, using excision, incision and dead space wounds models. The animals were divided into two groups of 6 each in all the models. In the excision model, group 1 animals were topically treated with carboxymethyl cellulose as placebo control and group 2 received topical application of the ethanol extract of C. roseus at a dose of 100 mg/kg body weight/day. In an incision and dead space model group 1 animals were given normal saline and group 2 received the extract orally at a dose of 100 mg kg-1 day-1. Healing was assessed by the rate of wound contraction, period of epithelization, tensile strength (skin breaking strength), granulation tissue weight, and hydoxyproline content. Antimicrobial activity of the flower extract against four microorganisms was also assessed Results The extract of C. roseus significantly increased the wound breaking strength in the incision wound model compared with controls (P < 0.001). The extract-treated wounds were found to epithelialize faster, and the rate of wound contraction was significantly increased in comparison to control wounds (P < 0.001), Wet and dry granulation tissue weights, and hydroxyproline content in a dead space wound model increased significantly (p < 0.05). Pseudomonas aeruginosa and Staphylococcus aureus demonstrated sensitivity to C. roseus Conclusion Increased wound contraction and tensile strength, augmented hydroxyproline content along with antimicrobial activity support the use of C. roseus in the topical management of wound healing. PMID:17184528

Mechanisms Governing Interannual Variability of Stratosphere-to-Troposphere Ozone Transport

NASA Astrophysics Data System (ADS)

Albers, John R.; Perlwitz, Judith; Butler, Amy H.; Birner, Thomas; Kiladis, George N.; Lawrence, Zachary D.; Manney, Gloria L.; Langford, Andrew O.; Dias, Juliana

2018-01-01

Factors governing the strength and frequency of stratospheric ozone intrusions over the Pacific-North American region are considered for their role in modulating tropospheric ozone on interannual timescales. The strength of the association between two major modes of climate variability—the El Niño-Southern Oscillation (ENSO) and the Northern Annular Mode (NAM)—and the amount of ozone contained in stratospheric intrusions are tested in the context of two mechanisms that modulate stratosphere-to-troposphere transport (STT) of ozone: (StratVarO3) the winter season buildup of ozone abundances in the lowermost stratosphere (LMS) and (JetVar) Pacific jet and wave breaking variability during spring. In essence, StratVarO3 corresponds to variability in the amount of ozone per intrusion, while JetVar governs the frequency of intrusions. The resulting analysis, based on two different reanalysis products, suggests that StratVarO3 is more important than JetVar for driving interannual variations in STT of ozone over the Pacific-North American region. In particular, the abundance of ozone in the LMS at the end of winter is shown to be a robust indicator of the amount of ozone that will be contained in stratospheric intrusions during the ensuing spring. Additionally, it is shown that the overall strength of the winter season stratospheric NAM is a useful predictor of ozone intrusion strength. The results also suggest a nuanced relationship between the phase of ENSO and STT of ozone. While ENSO-related jet variability is associated with STT variability, it is wave breaking frequency rather than typical ENSO teleconnection patterns that is responsible for the ENSO-STT relationship.

Characteristic study of chitosan addition in Tilapia (Oreochromis niloticus) bone based gelatin film

NASA Astrophysics Data System (ADS)

Atmaka, W.; Yudhistira, B.; Putro, M. I. S.

2018-03-01

Tilapia (Oreochromis niloticus) is one of popular fish species in Indonesia. The high number in tilapia’s production and export of tilapia resulting in the increase of bone fish waste. an attempt to decrease the amount of the aforementioned waste, the fish bones were turned into gelatine. The gelatine produced from this waste can be put to good use by turning it into edible film due to its high water resistance and low tensile strength value. However, in order to make a proper film, both the water resistance and the tensile strength value needs another appropriate additional biopolymer. In this case, the appropriate biopolymer needed both to form the film and to repair its characteristics is chitosan. The purpose of this research is to find out the effect of the chitosan addition on the tilapia bone based gelatine film. The research used several mixtures of gelatine (G) and chitosan (C) with the following ratio: G100:C0 (GC1), G75:C25 (GC2), G50:C50 (GC3), G25:C75 (GC4), G0:C100 (GC5). ANOVA results (P<0.05) shows that the addition of chitosan on the gelatine film affected its characteristics in thickness, solubility, tensile strength, elongation at break, Fourier Transform Infrared (FTIR), color a, and color b but no significant effects on the vapor permeability and color L. The best result is shown on GC2 with thickness 0.119 mm; solubility 74.95%; tensile strength 2.635 Mpa; elongation at break 68.26%; water vapor permeability 5.897 g/h m2 and FTIR. The parameters in GC2 shows good compatibility between the two biopolymers.

Four-Week Unstructured Break Improved Athletic Performance in Collegiate Rugby Players.

PubMed

Jensen, Courtney D; Gleason, Derrick; VanNess, Mark

2018-06-01

Jensen, CD, Gleason, D, and VanNess, JM. Four-week unstructured break improved athletic performance in collegiate rugby players. J Strength Cond Res 32(6): 1671-1677, 2018-This study analyzed the changes in athletic performance and anthropometric characteristics in collegiate male club rugby athletes (n = 14) after a 4-week winter break. All measurements were collected before and after the break. Body composition was assessed by body mass index and hydrostatic weighing. Performance measurements were as follows: V[Combining Dot Above]O2max, vertical jump, 10-yard sprint, squat max, and bench press max. Before testing, each subject was acclimated to the protocols to reduce learning effects. During the 4-week break, no workouts were provided for the athletes; it was unsupervised and unstructured. Participants were required to maintain and submit self-reported nutritional and activity logs during this period. After the break, the athletes demonstrated a 5.0% improvement in V[Combining Dot Above]O2max (absolute increase of 2.25 ml·kg·min), 6.8% improvement in vertical jump (1.50 inches), and a 14.3% increase in squat max (38.64 lb). Although increases in body mass (1.0%) were not significant, the body fat percentage exhibited a relative increase of 19.3% (absolute change from 13.35 to 15.93%). A significant discriminate function analysis indicated statistical differences between groups based on these variables. Self-reported behavior logs confirmed participation in >3 days of moderate to intense physical activity per week but somewhat poor dietary habits. These results indicate that collegiate rugby athletes may not need prescribed exercise routines during seasonal breaks in the athletic schedule. However, it may be beneficial to provide structured nutritional advice during unsupervised periods.

42 CFR 425.706 - Minimum necessary data.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) The claim payment type. (9) Date of birth and death, if applicable. (10) TIN. (11) NPI. (b) The.... (6) Days supplied. (7) Brand name. (8) Generic name. (9) Drug strength. (10) TIN. (11) NPI. (12...

42 CFR 425.706 - Minimum necessary data.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) The claim payment type. (9) Date of birth and death, if applicable. (10) TIN. (11) NPI. (b) The.... (6) Days supplied. (7) Brand name. (8) Generic name. (9) Drug strength. (10) TIN. (11) NPI. (12...

42 CFR 425.706 - Minimum necessary data.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) The claim payment type. (9) Date of birth and death, if applicable. (10) TIN. (11) NPI. (b) The.... (6) Days supplied. (7) Brand name. (8) Generic name. (9) Drug strength. (10) TIN. (11) NPI. (12...

Flow and turbulence structure in a hypertidal estuary with the world's biggest tidal bore

NASA Astrophysics Data System (ADS)

Tu, Junbiao; Fan, Daidu

2017-04-01

Turbulent and flow structure associated with breaking tidal bores are deliberately investigated on the basis of field measurements. High-resolution velocity and hydrographic data are collected in the middle Qiantang Estuary by a vertical array of acoustic Doppler velocimeters and optical backscatter sensors, collaborated with a bottom-mounted acoustic Doppler current profiler. Besides obvious variations in diurnal and spring-neap tidal cycles, the estuarine dynamics is featured by extreme asymmetry in flood and ebb tides. The flood tide is abnormally accelerated to generate tidal bores at the first 10 min or more, with breaking or undular configurations at the front. The occurrence of peak flow velocity, turbulent kinetic energy (TKE), and TKE dissipation rate (ɛ) is definitely associated with breaking bores, with their values several times to 2 orders of magnitude larger than the corresponding secondary peak values during the maximum ebb flows. Flow and turbulence dynamics are significantly affected by the tidal-bore Froude number. A sandwich ɛ structure is clear exhibited with the maximum value at the surface, secondary maximum near the bed, and the minimum at the intermediate. Dual TKE sources are indicated by an approximate local balance between shear production and dissipation near the bottom, and a top-down TKE dissipation using the modified Froude scaling in the vertical water column. The highly elevated dissipation by breaking bores is comparable to that by intense breaking waves in the surf zone, and the former potentially penetrates the entire water column to produce extreme sediment-resuspension events in combination with intense bottom shear stress.

Theory of vibratory mobilization and break-up of non-wetting fluids entrapped in pore constrictions

NASA Astrophysics Data System (ADS)

Beresnev, I.; Li, W.; Vigil, D.

2006-12-01

Quantitative dynamics of a non-wetting (e. g., NAPL) ganglion entrapped in a pore constriction and subjected to vibrations can be approximated by the equation of motion of an oscillator moving under the effect of the external pressure gradient, inertial oscillatory force, and restoring capillary force. The solution of the equation provides the conditions under which the droplet experiences forced oscillations without being mobilized or is liberated upon the acceleration of the wall exceeding an "unplugging" threshold. This solution provides a quantitative tool for the estimation of the parameters of vibratory fields needed to liberate entrapped non-wetting fluids. For typical pore sizes encountered in reservoirs and aquifers, wall accelerations must exceed at least several m/sec2 and even higher levels to mobilize the droplets of NAPL; however, in the populations of ganglia entrapped in natural porous environments, many may reside very near their mobilization thresholds and may be mobilized by extremely low accelerations as well. For given acceleration, lower seismic frequencies are more efficient. The ganglia may also break up into smaller pieces when passing through pore constrictions. The snap-off is governed by the geometry only; for constrictions with sinusoidal profile (spatial wavelength of L and maximum and minimum radii of rmax and rmin, the break-up occurs if L > 2π(rmin rmax)1/2. Computational fluid dynamics shows the details of the break-up process.

Landau level splitting in Cd3As2 under high magnetic fields

NASA Astrophysics Data System (ADS)

Zhang, Cheng; Cao, Junzhi; Liang, Sihang; Xia, Zhengcai; Li, Liang; Xiu, Faxian

2015-03-01

Three-dimensional (3D) topological Dirac semimetals (TDSs) are a new kind of Dirac materials that adopt nontrivial topology in band structure and possess degenerated massless Dirac fermions in the bulk. It has been proposed that TDSs can be driven to other exotic phases like Weyl semimetals, topological insulators and topological superconductors by breaking certain symmetries. Here we report the first transport evidence of Landau level splitting in TDS Cd3As2 single crystals under high magnetic fields, suggesting the removal of spin degeneracy by breaking time reversal symmetry (TRS). The observed Landau level splitting is originated from the joint contributions of orbit and Zeeman splitting in Cd3As2. In addition, the detected Berry phase is found to vary from nontrivial to trivial at different field directions, revealing a fierce competition between the orbit-coupled field strength and the field-generated mass term. Our results demonstrate a feasible path to generate a Weyl semimetal phase based on the TDSs by breaking TRS.

Effect of thermoplastic polyurethane (TPU) on the thermal and mechanical properties of polylactic acid (PLA)/curcumin blends

NASA Astrophysics Data System (ADS)

Sharifah, I. S. S.; Adnan, M. D. A.; Nor Khairusshima, M. K.; Shaffiar, N. M.; Buys, Y. F.

2018-01-01

Polylactic acid (PLA) is known to be brittle by nature and thus limits the flexibility of the polymer. A possible solution to enhance the flexibility of PLA is to add a flexible polymeric based material such as thermoplastic polyurethane (TPU). In this study, 30-50 wt% of TPU was added into PLA/curcumin blends to improve its flexibility. Thermal analysis using differential scanning calorimetry shows that further additions of TPU at the expense of PLA did not affect the glass transition temperature, crystallisation temperature and melting temperature of the blends. Fibers of PLA/curcumin/TPU were successfully drawn and Single Fiber Tensile Test (SFTT) showed vast improvement in elongation at break. The initial addition of 30 wt% of TPU to the brittle PLA/curcumin composition causes a significant increase in elongation at break by 39 times and further additions at 50 wt %, the elongation at break increases by 105 times. However, with the increase in elongation, a decrease in strength and Young’s modulus was observed.

Anthocyanin yield and skin softening during maceration, as affected by vineyard row orientation and grape ripeness of Vitis vinifera L. cv. Shiraz.

PubMed

Giacosa, Simone; Marengo, Fabio; Guidoni, Silvia; Rolle, Luca; Hunter, Jacobus J

2015-05-01

Anthocyanin and mechanical properties were evaluated on Shiraz grapes, picked from both sides of North-South and East-West vineyard row orientations at two harvest dates. Wines were made from each combination. The evaluation and evolution of crushed skin mechanical properties during maceration-fermentation, as also affected by grape ripeness, are shown for the first time. No significant differences in anthocyanin content were found in the grapes between the two vineyard row orientations. However, a significant decrease in anthocyanins and berry skin break force (also referred as skin hardness or strength) was found between the two harvest dates. During maceration, a reduction in the crushed berry skin break force of more than 15% occurred. The intact berries and macerated skins showed similarity in skin break energy values. The anthocyanin profile of the grapes and of the wines prominently displayed malvidin forms, changed mainly by the ripeness level of the grapes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Developing criteria for performance-based concrete specifications.

DOT National Transportation Integrated Search

2013-07-01

For more than 50 years now, concrete technology has advanced, but CDOT specifications for durability have : remained mostly unchanged. The minimum cement content for a given strength is derived from mix design : guidelines that were developed before ...

Factors affecting healing rates after arthroscopic double-row rotator cuff repair.

PubMed

Tashjian, Robert Z; Hollins, Anthony M; Kim, Hyun-Min; Teefey, Sharlene A; Middleton, William D; Steger-May, Karen; Galatz, Leesa M; Yamaguchi, Ken

2010-12-01

Double-row arthroscopic rotator cuff repairs were developed to improve initial biomechanical strength of repairs to improve healing rates. Despite biomechanical improvements, failure of healing remains a clinical problem. To evaluate the anatomical results after double-row arthroscopic rotator cuff repair with ultrasound to determine postoperative repair integrity and the effect of various factors on tendon healing. Case series; Level of evidence, 4. Forty-eight patients (49 shoulders) who had a complete arthroscopic rotator cuff repair (double-row technique) were evaluated with ultrasound at a minimum of 6 months after surgery. Outcome was evaluated at a minimum of 1-year follow-up with standardized history and physical examination, visual analog scale for pain, active forward elevation, and preoperative and postoperative shoulder scores according to the system of the American Shoulder and Elbow Surgeons and the Simple Shoulder Test. Quantitative strength was measured postoperatively. Ultrasound and physical examinations were performed at a minimum of 6 months after surgery (mean, 16 months; range, 6 to 36 months) and outcome questionnaire evaluations at a minimum of 12 months after surgery (mean, 29 months; range, 12 to 55 months). Of 49 repairs, 25 (51%) were healed. Healing rates were 67% in single-tendon tears (16 of 24 shoulders) and 36% in multitendon tears (9 of 25 shoulders). Older age and longer duration of follow-up were correlated with poorer tendon healing (P < .03). Visual analog scale for pain, active forward elevation, American Shoulder and Elbow Surgeons scores, and Simple Shoulder Test scores all had significant improvement from baseline after repair (P < .0001). Increased age and longer duration of follow-up were associated with lower healing rates after double-row rotator cuff repair. The biological limitation at the repair site, as reflected by the effects of age on healing, appears to be the most important factor influencing tendon healing, even after maximizing repair biomechanical strength with a double-row construct.

Entanglement entropy of a three-spin-interacting spin chain with a time-reversal-breaking impurity at one boundary.

PubMed

Nag, Tanay; Rajak, Atanu

2018-04-01

We investigate the effect of a time-reversal-breaking impurity term (of strength λ_{d}) on both the equilibrium and nonequilibrium critical properties of entanglement entropy (EE) in a three-spin-interacting transverse Ising model, which can be mapped to a p-wave superconducting chain with next-nearest-neighbor hopping and interaction. Importantly, we find that the logarithmic scaling of the EE with block size remains unaffected by the application of the impurity term, although, the coefficient (i.e., central charge) varies logarithmically with the impurity strength for a lower range of λ_{d} and eventually saturates with an exponential damping factor [∼exp(-λ_{d})] for the phase boundaries shared with the phase containing two Majorana edge modes. On the other hand, it receives a linear correction in term of λ_{d} for an another phase boundary. Finally, we focus to study the effect of the impurity in the time evolution of the EE for the critical quenching case where the impurity term is applied only to the final Hamiltonian. Interestingly, it has been shown that for all the phase boundaries, contrary to the equilibrium case, the saturation value of the EE increases logarithmically with the strength of impurity in a certain regime of λ_{d} and finally, for higher values of λ_{d}, it increases very slowly dictated by an exponential damping factor. The impurity-induced behavior of EE might bear some deep underlying connection to thermalization.

Effects of Hibiscus rosa sinensis L (Malvaceae) on wound healing activity: a preclinical study in a Sprague Dawley rat.

PubMed

Shivananda Nayak, B; Sivachandra Raju, S; Orette, F A; Chalapathi Rao, A V

2007-06-01

Hibiscus rosa sinensis (H rosa sinensis), a plant product, has been used for the treatment of a variety of diseases as well as to promote wound healing. The wound-healing activity of the ethanol extract of H rosa sinensis flower was determined in rats, using excision, incision, and dead space wound models and is presented in this report. The animals were randomly divided into 2 groups of 6 each in all the models. Test group animals in each model were treated with the ethanol extract of H rosa sinensis orally by mixing in drinking water (120 mg kg(-1) day(-1)), and the control group animals were maintained with plain drinking water. Healing was assessed by the rate of wound contraction, period of epithelialization, tensile strength (skin breaking strength), granulation tissue weight, and hydroxyproline content. The antimicrobial activity of the flower extract against selected microorganisms that infect the wounds was also assessed. Animals treated with the extract exhibited an 86% reduction in the wound area compared with controls, who exhibited a 75% reduction. The extract-treated animals were found to epithelize their wounds significantly faster than controls (P < .002) and have shown significantly higher skin-breaking strength than controls (P < .002). The dry and wet weight of granulation tissue and hydroxyproline content were also increased significantly when compared with controls. The reported observations suggest H rosa sinensis aids wound healing in the rat model.

Entanglement entropy of a three-spin-interacting spin chain with a time-reversal-breaking impurity at one boundary

NASA Astrophysics Data System (ADS)

Nag, Tanay; Rajak, Atanu

2018-04-01

We investigate the effect of a time-reversal-breaking impurity term (of strength λd) on both the equilibrium and nonequilibrium critical properties of entanglement entropy (EE) in a three-spin-interacting transverse Ising model, which can be mapped to a p -wave superconducting chain with next-nearest-neighbor hopping and interaction. Importantly, we find that the logarithmic scaling of the EE with block size remains unaffected by the application of the impurity term, although, the coefficient (i.e., central charge) varies logarithmically with the impurity strength for a lower range of λd and eventually saturates with an exponential damping factor [˜exp(-λd) ] for the phase boundaries shared with the phase containing two Majorana edge modes. On the other hand, it receives a linear correction in term of λd for an another phase boundary. Finally, we focus to study the effect of the impurity in the time evolution of the EE for the critical quenching case where the impurity term is applied only to the final Hamiltonian. Interestingly, it has been shown that for all the phase boundaries, contrary to the equilibrium case, the saturation value of the EE increases logarithmically with the strength of impurity in a certain regime of λd and finally, for higher values of λd, it increases very slowly dictated by an exponential damping factor. The impurity-induced behavior of EE might bear some deep underlying connection to thermalization.

Production of bioplastic from jackfruit seed starch (Artocarpus heterophyllus) reinforced with microcrystalline cellulose from cocoa pod husk (Theobroma cacao L.) using glycerol as plasticizer

NASA Astrophysics Data System (ADS)

Lubis, M.; Gana, A.; Maysarah, S.; Ginting, M. H. S.; Harahap, M. B.

2018-02-01

The production of bioplastic from jackfruit seed starch reinforced with microcrystalline cellulose (MCC) cocoa pod husk using glycerol as plasticizer was investigated to determine the most optimum mass and volume of MCC and glycerol in producing bioplastics. To produce MCC, Cocoa pod husk was subjected to alkali treatment, bleaching, and hydrochloric acid hydrolysis. The degree of crystallinity of MCC, were determined by XRD, functional group by FT-IR and morphologycal analysis by SEM. Analysis of bioplastic mechanical properties includes tensile strength and elongation at break based on ASTM D882 standard. Bioplastics were produced by casting method from jackfruit seed starch and reinforced with MCC from cocoa pod husk at starch mass to MCC ratio of 6:4, 7:3, 8:2, and 9:1, using glycerol as plasticizer at 20%, 25%, 30% (wt/v of glycerol to starch). From the result, the isolated MCC from cocoa pod husk were in a form of rod-like shape of length 5-10 µm with diameter 11.635 nm and 74% crystallinity. The highest tensile strength of bioplastics was obtained at starch to MCC mass ratio of 8:2, addition of 20% glycerol with measured tensile strength of 0.637 MPa and elongation at break of 7.04%. Transform infrared spectroscopy showed the functional groups of bioplastics, which the majority of O-H groups were found at the bioplastics with reinforcing filler MCC that represented substantial hydrogen bonds.

A model for wave control on coral breakage and species distribution in the Hawaiian Islands

USGS Publications Warehouse

Storlazzi, C.D.; Brown, E.K.; Field, M.E.; Rodgers, K.; Jokiel, P.L.

2005-01-01

The fringing reef off southern Molokai, Hawaii, is currently being studied as part of a multi-disciplinary project led by the US Geological Survey. As part of this study, modeling and field observations were utilized to help understand the physical controls on reef morphology and the distribution of different coral species. A model was developed that calculates wave-induced hydrodynamic forces on corals of a specific form and mechanical strength. From these calculations, the wave conditions under which specific species of corals would either be stable or would break due to the imposed wave-induced forces were determined. By combining this hydrodynamic force-balance model with various wave model output for different oceanographic conditions experienced in the study area, we were able to map the locations where specific coral species should be stable (not subject to frequent breakage) in the study area. The combined model output was then compared with data on coral species distribution and coral cover at 12 sites along Molokai's south shore. Observations and modeling suggest that the transition from one coral species to another may occur when the ratio of the coral colony's mechanical strengths to the applied (wave-induced) forces may be as great as 5:1, and not less than 1:1 when corals would break. This implies that coral colony's mechanical strength and wave-induced forces may be important in defining gross coral community structure over large (orders of 10's of meters) spatial scales. ?? Springer-Verlag 2004.

Physical and functional comparison of Coated VICRYL* Plus Antibacterial Suture (coated polyglactin 910 suture with triclosan) with Coated VICRYL* Suture (coated polyglactin 910 suture).

PubMed

Storch, Mark; Scalzo, Howard; Van Lue, Stephen; Jacinto, Gabriel

2002-01-01

The goal of this study was to compare the physical and functional properties of coated polyglactin 910 suture with and without triclosan by human assessment and instrument-based measurements. Surgeons specializing in general, orthopedic, plastic, or gynecologic surgery evaluated the suture materials in an in vivo porcine model with regard to (1) ease of passage through tissue, (2) first-throw knot holding, (3) knot tie-down smoothness, (4) knot security, (5) surgical handling, and (6) overall evaluation. Breaking strength retention was determined at 14, 21, 28, and 35 days post-implantation in rats using a tensile strength measurement device. The absorption rate was determined in rats by histopathology at 7, 28, 56, 63, 70, and 77 days post-implantation. The tactile smoothness and tie-down behavior of both wet and dry sutures were evaluated by product characterization technicians. The scores for surgeons' evaluation of suture material were favorable and similar for both sutures. Surgeons could not reliably make a distinction in handling between the two sutures. Breaking strength retention was the same for both sutures, ranging from 79% on day 14 to 5% on day 35. Both sutures were essentially absorbed at 70 days post-implantation. Product characterization assessment of the two sutures found them to be indistinguishable. The addition of triclosan to coated polyglactin 910 sutures did not affect physical handling properties or performance characteristics based on the testing and evaluations performed.

Predictions of thermal buckling strengths of hypersonic aircraft sandwich panels using minimum potential energy and finite element methods

NASA Technical Reports Server (NTRS)

Ko, William L.

1995-01-01

Thermal buckling characteristics of hypersonic aircraft sandwich panels of various aspect ratios were investigated. The panel is fastened at its four edges to the substructures under four different edge conditions and is subjected to uniform temperature loading. Minimum potential energy theory and finite element methods were used to calculate the panel buckling temperatures. The two methods gave fairly close buckling temperatures. However, the finite element method gave slightly lower buckling temperatures than those given by the minimum potential energy theory. The reasons for this slight discrepancy in eigensolutions are discussed in detail. In addition, the effect of eigenshifting on the eigenvalue convergence rate is discussed.

Influence of proximal end diverting colostomy on the healing of left-sided colonic anastomosis: an experimental study in rats.

PubMed

Bielecki, K; Grotowski, M; Kalczak, M

1995-01-01

The purpose of this study was to evaluate the healing of an experimental left-sided colonic anastomosis in rats protected by an end diverting proimal colostomy. The anastomoses were studied by radiological and biochemical examination and breaking strength was estimated. The results were compared with a non-operated group and with a group of rats having a non-defunctional anastomosis constructed in the same manner. In animals with an end diverting colostomy, anastomotic protein levels and enzymic activity were lower than in those with a colostomy, and the development of anastomotic strength was delayed compared with those not defunctioned.

Kevlar reinforced neoprene composites

NASA Technical Reports Server (NTRS)

Penn, B. G.; Daniels, J. G.; White, W. T.; Thompson, L. M.; Clemons, L. M.

1985-01-01

Kevlar/neoprene composites were prepared by two techniques. One method involved the fabrication of a composite from a rubber prepreg prepared by coating Kevlar with viscous neoprene solution and then allowing the solvent to evaporate (solution impregnation technique). The second method involved heating a stack of Kevlar/neoprene sheets at a temperature sufficient to cause polymer flow (melt flow technique). There was no significant difference in the breaking strength and percent elongation for samples obtained by the two methods; however the shear strength obtained for samples fabricated by the solution impregnation technique (275 psi) was significantly higher than that found for the melt flow fabricated samples (110 psi).

Morphological and Mechanical Properties of Polypropylene[PP]/Poly(Ethylene Vinyl Acetate)[EVA] Blends. I. Homopolymer PP/Eva Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramirez-Vargas, E.

2000-10-01

Morphological and mechanical properties of polypropylene [PP]/poly(ethylene vinyl acetate) [EVA] blends have been studied. Infrared results using thin films first indicated a transition toward compatibility between both components at concentrations above 40% EVA. The transition was verified with different experimental techniques and it was associated to morphological changes and mechanical properties. The PP/EVA blends were mechanically evaluated in terms of impact and tensile strength to determine the influence of blending on the performance properties of these materials. Agreement was found between the transition and the enhancement of both elongation at break and impact strength.

Heat waves and jet stream relations - nature of dry and wet shifts around the 2.8 kyr BP event in Central Europe

NASA Astrophysics Data System (ADS)

Slowinski, M. M.; Persoiu, A.; Slowinska, S.; Marcisz, K.; Ionita, M.; Lamentowicz, M.

2017-12-01

Solar insolation was the main driver of N Hemisphere storm tracks changes, with significant impacts on European climate variability during the Holocene. Consequently, the Homeric solar minimum, which occurred between 2,750 and 2,550 cal BP, was characterized by cooling and increase in wind strength and humidity in W Europe. In contrast, environmental reconstructions from Central and E Europe show that the climatic changes during this period were often more complex, with increased hydrological instability and a shift towards drier conditions. These contrasting conditions could be explained by the blocking in a stationary position of a high-pressure system above Central and E Europe as a result of the behavior of the jet stream. In order to understand how these changes in the behavior of the jet stream were acting in the past, we have analyzed a modern analogue to better understand the climatic map of Europe during the Homeric minimum of the 9th century BC. Thus, in summer 2015, a northward extending meander of the jet stream led to dry and hot conditions in C Europe, blocking the transport of Atlantic-sourced moisture eastwards and leading to increased precipitation in W Europe. Contrary, in 2013, the position of the high-pressure cells associated with the meandering of the jet-stream was located over W Russia and E Europe (both affected by heat waves resulting from meridional advection of dry/hot air), leading to more Rossby waves breaking over C Europe and delivering record amounts of precipitation. To test whether a similar mechanism could act on longer times scales, we have analyzed two high-resolution palaeoclimate datasets from E Europe (Rąbień peatbog, Poland and Scăriloara Ice Cave, Romania), located in areas with both N Atlantic and Mediterranean climatic influences. At the time of the Homeric Solar Minimum, warm climatic conditions dominated in SE Europe, with advection of warm and dry air from the Mediterranean. W Europe was rather wet around that time and these contrasting conditions could have been the result of blocking conditions over C Europe, induced by a solar-influenced strongly meandering jet-stream. Our recent monitoring observation and paleoclimate data support studies that presents link between arctic polar vortex, jet streams, sea-ice formation in the Arctic and climate variability in Europe.

Composite strengthening. [of nonferrous, fiber reinforced alloys

NASA Technical Reports Server (NTRS)

Stoloff, N. S.

1976-01-01

The mechanical behavior of unidirectionally reinforced metals is examined, with particular attention to fabrication techniques for artificial composites and eutectic alloys and to principles of fiber reinforcement. The properties of artificial composites are discussed in terms of strength of fiber composites, strength of ribbon-reinforced composites, crack initiation, crack propagation, and creep behavior. The properties of eutectic composites are examined relative to tensile strength, compressive strength, fracture, high-temperature strength, and fatigue. In the case of artificial composites, parallelism of fibers, good bonding between fibers and matrix, and freedom of fibers from damage are all necessary to ensure superior performance. For many eutectic systems there are stringent boundary conditions relative to melt purity and superheat, atmosphere control, temperature gradient, and growth rate in order to provide near-perfect alignment of the reinforcements with a minimum of growth defects.

The Theory of Distributed Practice as Related to Acquisition of Psychomotor Skills by Adolescents in a Selected Curricular Field.

ERIC Educational Resources Information Center

Drake, James Bob

1981-01-01

From results on the tensile strength and nick-break average jury evaluations test, it was concluded that with the same total practice time, different distributions of welding practice time intervals (15, 30, and 45 minutes) influence the quality of butt welds made by ninth-grade vocational agriculture students. (Author/SJL)

A Critical Analysis and Assessment of High Power Switches

DTIC Science & Technology

1978-09-01

applications. Because of field-distorting corona discharges in high voltage gas gaps it is difficult to predict the exact break- down strength of a nonuniform ...applied field. The streamer velocity is a/R Vs =E 2 a/R (A-9) i n i - laiR -i e o 411 where S= mobility of electrons E = applied electric field a = length

Germany knows mining

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Whether it is the nuance of precision or robust rock breaking strength, German suppliers have the expertise. Germany has about 120 companies in the mining equipment industry, employing some 16,000 people. The article describes some recent developments of the following companies: DBT, Liebherr, Atlas Copco, BASF, Boart Longyear, Eickhoff, IBS, Maschinenfabrik Glueckauf, Komatsu, TAKRA, Terex O & R, Thyssen Krupp Foerdertechnik and Wirtgen. 7 photos.

46 CFR 169.537 - Description of equipment for lifefloats.

Code of Federal Regulations, 2014 CFR

2014-10-01

... between the deck on which the life float(s) are stowed and the light draft of the vessel, (2) Have a... persons or more, the breaking strength must be at least 13.4 KN (3000 lbs.), (3) Be of a dark color, if synthetic, or of a type certified to be resistant to deterioration from ultraviolet light, and (4) Be stowed...

46 CFR 169.537 - Description of equipment for lifefloats.

Code of Federal Regulations, 2010 CFR

2010-10-01

... between the deck on which the life float(s) are stowed and the light draft of the vessel, (2) Have a... persons or more, the breaking strength must be at least 13.4 KN (3000 lbs.), (3) Be of a dark color, if synthetic, or of a type certified to be resistant to deterioration from ultraviolet light, and (4) Be stowed...

46 CFR 169.537 - Description of equipment for lifefloats.

Code of Federal Regulations, 2013 CFR

2013-10-01

... between the deck on which the life float(s) are stowed and the light draft of the vessel, (2) Have a... persons or more, the breaking strength must be at least 13.4 KN (3000 lbs.), (3) Be of a dark color, if synthetic, or of a type certified to be resistant to deterioration from ultraviolet light, and (4) Be stowed...

The Tower and Glass Marbles Problem

ERIC Educational Resources Information Center

Denman, Richard T.; Hailey, David; Rothenberg, Michael

2010-01-01

The Catseye Marble company tests the strength of its marbles by dropping them from various levels of their office tower, to find the highest floor from which a marble will not break. We find the smallest number of drops required and from which floor each drop should be made. We also find out how these answers change if a restriction is placed on…

Oceanography and Mine Warfare

DTIC Science & Technology

2000-03-13

of breaking waves , the position and strength of surface currents, and the propagation of the tide into very shallow waters. In the surf zone...6) sediment properties determine shock wave propagation , a method for mine neutralization in the surf zone. 48 OCEANOGRAPHY AND MINE WARFARE...mines will be buried in the sediments, sedimentary explosive shock wave propagation is critical for determining operational performance. Presently, we

Potential Performance Criteria for Combat Ration Packs - Texture Profile Analysis

DTIC Science & Technology

2014-11-01

12 3.3.1 Apricot & coconut muesli bar...Figure 5 Texture vs aw of canned puddings stored at 30 °C for up to 730 days. 3.3 Muesli Bar The three muesli bars (apricot and coconut , tropical...Apricot & coconut muesli bar No significant changes were observed during storage for texture attributes, except at 40 °C for break strength and

46 CFR 160.073-10 - Construction and performance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... in figure 160.073-10. The link must be formed from a single salt water corrosion-resistant wire. A loop at least 50 mm (2 in.) in diameter must be provided at each end of the wire. Each loop must be permanently secured. (b) The breaking strength of each link must be between: (1) 450 N (100 lb.) and 600 N...

46 CFR 160.073-10 - Construction and performance.

Code of Federal Regulations, 2011 CFR

2011-10-01

... in figure 160.073-10. The link must be formed from a single salt water corrosion-resistant wire. A loop at least 50 mm (2 in.) in diameter must be provided at each end of the wire. Each loop must be permanently secured. (b) The breaking strength of each link must be between: (1) 450 N (100 lb.) and 600 N...

46 CFR 160.073-10 - Construction and performance.

Code of Federal Regulations, 2013 CFR

2013-10-01

... in figure 160.073-10. The link must be formed from a single salt water corrosion-resistant wire. A loop at least 50 mm (2 in.) in diameter must be provided at each end of the wire. Each loop must be permanently secured. (b) The breaking strength of each link must be between: (1) 450 N (100 lb.) and 600 N...

46 CFR 160.073-10 - Construction and performance.

Code of Federal Regulations, 2012 CFR

2012-10-01

... in figure 160.073-10. The link must be formed from a single salt water corrosion-resistant wire. A loop at least 50 mm (2 in.) in diameter must be provided at each end of the wire. Each loop must be permanently secured. (b) The breaking strength of each link must be between: (1) 450 N (100 lb.) and 600 N...

46 CFR 160.073-10 - Construction and performance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... in figure 160.073-10. The link must be formed from a single salt water corrosion-resistant wire. A loop at least 50 mm (2 in.) in diameter must be provided at each end of the wire. Each loop must be permanently secured. (b) The breaking strength of each link must be between: (1) 450 N (100 lb.) and 600 N...

Characteristics of a Healthy Family and Family Strengths: A Cross-Cultural Study.

ERIC Educational Resources Information Center

Lin, Phylis Lan; Chen, Jeaw-mei

This study explored how American and Taiwanese students viewed the ideal model of a healthy family in the 1980s and showed that contemporary families are changing and coping, not breaking up and dying. The subjects were 649 students from six universities in Indiana and Taiwan. The questionnaire was composed of 127 items that focused on five…

Strength properties of interlocking compressed earth brick units

NASA Astrophysics Data System (ADS)

Saari, S.; Bakar, B. H. Abu; Surip, N. A.

2017-10-01

This study presents a laboratory investigation on the properties of interlocking compressed earth brick (ICEB) units. Compressive strength, which is one of the most important properties in masonry structures, is used to determine masonry performance. The compressive strength of the ICEB units was determined by applying a compressive strength test for 340 units from four types of ICEB. To analyze the strength of the ICEB units, each unit was capped by a steel plate at the top and bottom to create a flat surface, and then ICEB was loaded until failure. The average compressive strength of the corresponding ICEB units are as follows: wall brick, 19.15 N/mm2; beam brick, 16.99 N/mm2; column brick, 13.18 N/mm2; and half brick, 11.79 N/mm2. All the ICEB units had compressive strength of over 5 N/mm2, which is the minimum strength for a load-bearing brick. This study proves that ICEB units may be used as load-bearing bricks. The strength of ICEBs is equal to that of other common bricks and blocks that are currently available in the market.

Coupling of Molecular Emitters and Plasmonic Cavities beyond the Point-Dipole Approximation.

PubMed

Neuman, Tomáš; Esteban, Ruben; Casanova, David; García-Vidal, Francisco J; Aizpurua, Javier

2018-04-11

As the size of a molecular emitter becomes comparable to the dimensions of a nearby optical resonator, the standard approach that considers the emitter to be a point-like dipole breaks down. By adoption of a quantum description of the electronic transitions of organic molecular emitters, coupled to a plasmonic electromagnetic field, we are able to accurately calculate the position-dependent coupling strength between a plasmon and an emitter. The spatial distribution of excitonic and photonic quantum states is found to be a key aspect in determining the dynamics of molecular emission in ultrasmall cavities both in the weak and strong coupling regimes. Moreover, we show that the extreme localization of plasmonic fields leads to the selection rule breaking of molecular excitations.

Determination of Stress-Corrosion Cracking in Aluminum-Lithium Alloy ML377

NASA Technical Reports Server (NTRS)

Valek, Bryan C.

1995-01-01

The use of aluminum-lithium alloys for aerospace applications is currently being studied at NASA Langley Research Center's Metallic Materials Branch. The alloys in question will operate under stress in a corrosive environment. These conditions are ideal for the phenomena of Stress-Corrosion Cracking (SCC) to occur. The test procedure for SCC calls for alternate immersion and breaking load tests. These tests were optimized for the lab equipment and materials available in the Light Alloy lab. Al-Li alloy ML377 specimens were then subjected to alternate immersion and breaking load tests to determine residual strength and resistance to SCC. Corrosion morphology and microstructure were examined under magnification. Data shows that ML377 is highly resistant to stress-corrosion cracking.

Unconventional Superconductivity in La(7)Ir(3) Revealed by Muon Spin Relaxation: Introducing a New Family of Noncentrosymmetric Superconductor That Breaks Time-Reversal Symmetry.

PubMed

Barker, J A T; Singh, D; Thamizhavel, A; Hillier, A D; Lees, M R; Balakrishnan, G; Paul, D McK; Singh, R P

2015-12-31

The superconductivity of the noncentrosymmetric compound La(7)Ir(3) is investigated using muon spin rotation and relaxation. Zero-field measurements reveal the presence of spontaneous static or quasistatic magnetic fields below the superconducting transition temperature T(c)=2.25  K-a clear indication that the superconducting state breaks time-reversal symmetry. Furthermore, transverse-field rotation measurements suggest that the superconducting gap is isotropic and that the pairing symmetry of the superconducting electrons is predominantly s wave with an enhanced binding strength. The results indicate that the superconductivity in La(7)Ir(3) may be unconventional and paves the way for further studies of this family of materials.

Observation of scale invariance and conformal symmetry breaking in expanding Fermi gases

NASA Astrophysics Data System (ADS)

Elliott, Ethan; Joseph, James; Thomas, John

2014-05-01

We precisely test scale invariance and examine local thermal equilibrium in the hydrodynamic expansion of a Fermi gas of atoms as a function of interaction strength. After release from an anisotropic optical trap, we observe that a resonantly interacting gas obeys scale-invariant hydrodynamics, where the mean square cloud size = expands ballistically (like a noninteracting gas) and the energy-averaged bulk viscosity is consistent with zero, 0 . 00 (0 . 04) ℏ n , with n the density. In contrast, the aspect ratios of the cloud exhibit anisotropic ``elliptic'' flow with an energy-dependent shear viscosity. Tuning away from resonance, we observe conformal symmetry breaking, where deviates from ballistic flow. NSF, DOE, ARO, AFO.

The breaking of flavor democracy in the quark sector

NASA Astrophysics Data System (ADS)

Fritzsch, Harald; Xing, Zhi-Zhong; Zhang, Di

2017-09-01

The democracy of quark flavors is a well-motivated flavor symmetry, but it must be properly broken in order to explain the observed quark mass spectrum and flavor mixing pattern. We reconstruct the texture of flavor democracy breaking and evaluate its strength in a novel way, by assuming a parallelism between the Q=+2/3 and Q=-1/3 quark sectors and using a nontrivial parametrization of the flavor mixing matrix. Some phenomenological implications of such democratic quark mass matrices, including their variations in the hierarchy basis and their evolution from the electroweak scale to a super-high energy scale, are also discussed. Supported by National Natural Science Foundation of China (11375207) and National Basic Research Program of China (2013CB834300)

Optical transparency and mechanical properties of semi-refined iota carrageenan film reinforced with SiO2 as food packaging material

NASA Astrophysics Data System (ADS)

Aji, Afifah Iswara; Praseptiangga, Danar; Rochima, Emma; Joni, I. Made; Panatarani, Camellia

2018-02-01

Food packaging is important for protecting food from environmental influences such as heat, light, water vapor, oxygen, dirt, dust particles, gas emissions and so on, which leads to decrease the quality of food. The most widely used type of packaging in the food industry is plastic which is made from synthetic polymers and takes hundreds of years to biodegrade. Recently, food packaging with high bio-degradability is being developed using biopolymer combined with nanoparticles as reinforcing agent (filler) to improve its properties. In this study, semi-refined iota carrageenan films were prepared by incorporating SiO2 nanoparticles as filler at different concentrations (0%, 0.5%, 1.0% and 1.5% w/w carrageenan) using solution casting method. The optical transparency and mechanical properties (tensile strength and elongation at break) of the films were analyzed. The results showed that incorporation of SiO2 nanoparticles to carrageenan matrix on optical transparency of the films. For the mechanical properties, the highest tensile strength was found for incorporation of 0.5% SiO2, while the elongation at break of the films improved with increasing SiO2 concentration.

Effect of carboxylic acids as compatibilizer agent on mechanical properties of thermoplastic starch and polypropylene blends.

PubMed

Martins, Andréa Bercini; Santana, Ruth Marlene Campomanes

2016-01-01

In this work, polypropylene/thermoplastic starch (PP/TPS) blends were prepared as an alternative material to use in disposable packaging, reducing the negative polymeric environmental impact. Unfortunately, this material displays morphological characteristics typical of immiscible polymer blends and a compatibilizer agent is needed. Three different carboxyl acids: myristic (C14), palmitic (C16) and stearic acids (C18) were used as natural compatibilizer agent (NCA). The effects of NCA on the mechanical, physical, thermal and morphological properties of PP/TPS blends were investigated and compared against PP/TPS with and without PP-grafted maleic anhydride (PPgMA). When compared to PP/TPS, blends with C18, PPgMA and C14 presented an improvement of 25, 22 and 17% in tensile strength at break and of 180, 194 and 259% in elongation at break, respectively. The highest increase, 54%, in the impact strength was achieved with C14 incorporation. Improvements could be seen, through scanning electron microscopy (SEM) images, in the compatibility between the immiscible components by acids incorporation. These results showed that carboxylic acids, specifically C14, could be used as compatibilizer agent and could substitute PPgMA. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of reaction time and polyethylene glycol monooleate-isocyanate composition on the properties of polyurethane-polysiloxane modified epoxy

NASA Astrophysics Data System (ADS)

Triwulandari, Evi; Ramadhan, Mohammad Kemilau; Ghozali, Muhammad

2017-11-01

Polyurethane-polysiloxane modified epoxy based on polyethylene glycol monooleate (PSME-PEGMO) was synthesized. Polyethylene glycol monooleate (PEGMO) for the synthesis of PSME-GMO was synthesized via esterification between oleic acid and polyethylene glycol by using sodium hydroxide as catalyst. Synthesis of PSME-PEGMO was conducted by reacting epoxy, isocyanate, PEGMO, and polysiloxane (hydrolyzed and condensable 3-glycidyloxypropyltrimethoxysilane) simultaneously in one step. This synthesis was carried out by varied the reaction time (1, 2, 3 hours), PEGMO-isocyanate composition (PI composition: 10 and 20 % toward epoxy), and isocyanate/PEGMO ratio (NCO/OH ratio: 1.5 and 2.5). Characterization of PSME-PEGMO was conducted by determining the isocyanate conversion, viscosity analysis, mechanical properties (tensile strength and elongation at break) and thermal analysis using thermogravimetric analysis (TGA). The data show that the PI composition and NCO/OH ratio does not affect the isocyanate conversion linearly. The viscosity of PSME-PEGMO product at ratio and composition variation show has tended to increase with increasing of reaction time. The highest tensile strength and elongation at break PSME-PEGMO was shown by PI composition 20%, NCO/OH ratio 2.5 and reaction time 3 hours.

Trapping and breaking of in vivo nicked DNA during pulsed-field gel electrophoresis

PubMed Central

Khan, Sharik R.; Kuzminov, Andrei

2013-01-01

Pulsed field gel electrophoresis (PFGE) offers a high-resolution approach to quantify chromosomal fragmentation in bacteria, measured as percent of chromosomal DNA entering the gel. The degree of separation in PFG depends upon the size of DNA, as well as various conditions of electrophoresis, such as electric field strength (FS), time of electrophoresis, switch time and buffer composition. Here we describe a new parameter, the structural integrity of the sample DNA itself, that influences its migration through PFGs. We show that sub-chromosomal fragments containing both spontaneous and DNA damage-induced nicks are prone to breakage during PFGE. Such breakage at single strand interruptions results in artefactual decrease in molecular weight of linear DNA making accurate determination of the number of double strand breaks difficult. While breakage of nicked sub-chromosomal fragments is FS-independent, some high molecular weight sub-chromosomal fragments are also trapped within wells under the standard PFGE conditions. This trapping can be minimized by lowering the field strength and increasing the time of electrophoresis. We discuss how breakage of nicked DNA may be mechanistically linked to trapping. Our results suggest how to optimize conditions for PFGE when quantifying chromosomal fragmentation induced by DNA damage. PMID:23770235

Simulation of breaking waves using the high-order spectral method with laboratory experiments: Wave-breaking onset

NASA Astrophysics Data System (ADS)

Seiffert, Betsy R.; Ducrozet, Guillaume; Bonnefoy, Félicien

2017-11-01

This study investigates a wave-breaking onset criteria to be implemented in the non-linear potential flow solver HOS-NWT. The model is a computationally efficient, open source code, which solves for the free surface in a numerical wave tank using the High-Order Spectral (HOS) method. The goal of this study is to determine the best method to identify the onset of random single and multiple breaking waves over a large domain at the exact time they occur. To identify breaking waves, a breaking onset criteria based on the ratio of local energy flux velocity to the local crest velocity, introduced by Barthelemy et al. (2017) is selected. The breaking parameter is uniquely applied in the numerical model in that calculations of the breaking onset criteria ratio are not made only at the location of the wave crest, but at every point in the domain and at every time step. This allows the model to calculate the onset of a breaking wave the moment it happens, and without knowing anything about the wave a priori. The application of the breaking criteria at every point in the domain and at every time step requires the phase velocity to be calculated instantaneously everywhere in the domain and at every time step. This is achieved by calculating the instantaneous phase velocity using the Hilbert transform and dispersion relation. A comparison between more traditional crest-tracking techniques shows the calculation of phase velocity using Hilbert transform at the location of the breaking wave crest provides a good approximation of crest velocity. The ability of the selected wave breaking criteria to predict single and multiple breaking events in two dimensions is validated by a series of large-scale experiments. Breaking waves are generated by energy focusing and modulational instability methods, with a wide range of primary frequencies. Steep irregular waves which lead to breaking waves, and irregular waves with an energy focusing wave superimposed are also generated. This set of waves provides a wide range of breaking-wave strengths, types and scales for validation of the model. A comparison of calculations made using HOS-NWT with experimental measurements show that the model is successful at predicting the occurrence of wave breaking, as well as accurately calculating breaking onset time and location. Although the current study is limited to a unidirectional wave field, the success of the wave-breaking model presented provides the basis for application of the model in a multidirectional wave field. By including wave breaking onset with the addition of an appropriate energy dissipation model into HOS-NWT, we can increase the application range of the model, as well as decrease the occurrence of numerical instabilities that are associated with breaking waves in a potential flow solver. An accurate description of the wave field is useful for predicting the dynamic response of offshore vessels and marine renewable energy devices, predicting loads on marine structures and the general physics of ocean waves, for example.

Observations of shallow water marine ambient sound: the low frequency underwater soundscape of the central Oregon coast.

PubMed

Haxel, Joseph H; Dziak, Robert P; Matsumoto, Haru

2013-05-01

A year-long experiment (March 2010 to April 2011) measuring ambient sound at a shallow water site (50 m) on the central OR coast near the Port of Newport provides important baseline information for comparisons with future measurements associated with resource development along the inner continental shelf of the Pacific Northwest. Ambient levels in frequencies affected by surf-generated noise (f < 100 Hz) characterize the site as a high-energy end member within the spectrum of shallow water coastal areas influenced by breaking waves. Dominant sound sources include locally generated ship noise (66% of total hours contain local ship noise), breaking surf, wind induced wave breaking and baleen whale vocalizations. Additionally, an increase in spectral levels for frequencies ranging from 35 to 100 Hz is attributed to noise radiated from distant commercial ship commerce. One-second root mean square (rms) sound pressure level (SPLrms) estimates calculated across the 10-840 Hz frequency band for the entire year long deployment show minimum, mean, and maximum values of 84 dB, 101 dB, and 152 dB re 1 μPa.

Microfluidic breakups of confined droplets against a linear obstacle: The importance of the viscosity contrast

NASA Astrophysics Data System (ADS)

Salkin, Louis; Courbin, Laurent; Panizza, Pascal

2012-09-01

Combining experiments and theory, we investigate the break-up dynamics of deformable objects, such as drops and bubbles, against a linear micro-obstacle. Our experiments bring the role of the viscosity contrast Δη between dispersed and continuous phases to light: the evolution of the critical capillary number to break a drop as a function of its size is either nonmonotonic (Δη>0) or monotonic (Δη≤0). In the case of positive viscosity contrasts, experiments and modeling reveal the existence of an unexpected critical object size for which the critical capillary number for breakup is minimum. Using simple physical arguments, we derive a model that well describes observations, provides diagrams mapping the four hydrodynamic regimes identified experimentally, and demonstrates that the critical size originating from confinement solely depends on geometrical parameters of the obstacle.

The engineering of construction specifications for externally bonded FRP composites

NASA Astrophysics Data System (ADS)

Yang, Xinbao

This dissertation, consisting of six technical papers, presents the results of research on the theme of developing engineering and the construction specifications for externally bonded FRP composites. For particular, the work focuses on three critical aspects of the performance of FRP systems: fiber misalignment, corner radius, and lap splice length. Based on both experimental and theoretical investigations, the main contribution of this work is the development of recommendations on fiber misalignment limit, minimum corner radius, lap splice length to be used as guidance in the construction practice of FRP strengthening of concrete structures. The first three papers focus on the strength and stiffness degradation of CFRP laminates from fiber misalignment. It was concluded that misalignment affects strength more than stiffness. In practice, when all fibers in a laminate can be regarded as through fibers, it is recommended to use a reduction factor for strength and no reduction factor for stiffness to account for fiber misalignment. Findings from concrete beams strengthened with misaligned CFRP laminates verified these recommendations. The fourth and fifth papers investigate the effect of corner radius on the mechanical properties of CFRP laminates wrapped around a rectangular cross section. A unique reusable test device was fabricated to determine fiber stress and radial stress of CFRP laminates with different corner radii. Comparison performed with finite element analyses shows that the test method and the reusable device were viable and the stress concentration needs to be considered in FRP laminate wrapped corners. A minimum of 1.0 in. corner radius was recommended for practice. The sixth paper summarizes the research on the lap splice length of FRP laminates under static and repeated loads. Although a lap splice length of 1.5 in. is sufficient for CFRP laminates to develop the ultimate static tensile strength, a minimum of 4.0 in. is recommended in order to account for repeated loads.

Experimental and Modeling Study on Detachment of Silver Nanoparticles in Saturated Granular Media

NASA Astrophysics Data System (ADS)

Kim, I.; Jeon, C. H.; Lawler, D. F.

2017-12-01

The detachment of citrate-capped silver nanoparticles (AgNPs) previously captured in a column packed with 350-μm glass beads was investigated either by increasing the hydrodynamic force (filtration velocity) or by reducing electrosteric attraction. Overall, the physical enforcement showed negligible (0.4 0.7%) release of attached AgNPs while the chemically-driven force resulted in the noticeable release up to 25.5% of attached AgNPs. Among the chemical parameters tested in this study, Na ionic strength reduction clearly demonstrated the reversible deposition in the secondary energy minimum of classical DLVO theory, yielding the most significant release of the attached AgNPs. The immediate and transient AgNP release after the ionic strength reduction further corroborated the weak deposition. However, an insignificant release was observed with Ca ionic strength reduction due to the strong Ca-citrate complexation and the subsequent deposition in the primary energy minimum; calculations indicated that the depth of the secondary energy minimum was only 1/10 that of the Na ion case. The natural organic matter (NOM) coating on both AgNPs and granular media resulted in approximately 6.1% greater AgNP release compared to the case without NOM coating, indicating additional weak deposition due to the reduced steric attraction between AgNPs and granular media. A modified filtration model in agreement with the experimental data provided the estimated detachment coefficient as a transient AgNP releasing capacity independent of the amount of attached AgNPs. The marginal difference between the detachment coefficients from Na ionic strength reduction and NOM coating indicates the release potential by NOM coating was possibly underestimated in the experimental study due to a lesser amount of the initially attached AgNPs. The findings provide insights into chemical factors on possible reentrainment behavior of the engineered nanoparticles in soil and groundwater contamination.

Strength Loss in MA-MOX Green Pellets from Radiation Damage to Binders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paul A. Lessing; W.R. Cannon; Gerald W. Egeland

The fracture strength of green Minor Actinides (MA)-MOX pellets containing 75 wt.% DUO2, 20 wt. % PuO2, 3 wt. % AmO2 and 2 wt. % NpO2 was studied as a function of storage time, after mixing in the binder and before sintering, to test the effect of radiation damage on binders. Fracture strength degraded continuously over the 10 days of the study for all three binders studied: PEG binder (Carbowax 8000), microcrystalline wax (Mobilcer X) and Styrene-acrylic copolymer (Duramax B1022) but the fracture strength of Duramax B1022 degraded the least. For instance, for several hours after mixing Carbowax 8000 withmore » MA MOX, the fracture strength of a pellet was reasonably high and pellets were easily handled without breaking but the pellets were too weak to handle after 10 days. Strength measured using diametral compression test showed strength degradation was more rapid in pellets containing 1.0 wt. % Carbowax PEG 8000 compared to those containing only 0.2 wt. %, suggesting that irradiation not only left the binder less effective but also reduced the pellet strength. In contrast the strength of pellets containing Duramax B1022 degraded very little over the 10 day period. It was suggested that the styrene portion of the Duramax B1022 copolymer provided the radiation resistance.« less

30 CFR 75.1904 - Underground diesel fuel tanks and safety cans.

Code of Federal Regulations, 2011 CFR

2011-07-01

...— (1) Have steel walls of a minimum 3/16-inch thickness, or walls made of other metal of a thickness that provides equivalent strength; (2) Be protected from corrosion; (3) Be of seamless construction or...

30 CFR 75.1904 - Underground diesel fuel tanks and safety cans.

Code of Federal Regulations, 2014 CFR

2014-07-01

...— (1) Have steel walls of a minimum 3/16-inch thickness, or walls made of other metal of a thickness that provides equivalent strength; (2) Be protected from corrosion; (3) Be of seamless construction or...

30 CFR 75.1904 - Underground diesel fuel tanks and safety cans.

Code of Federal Regulations, 2012 CFR

2012-07-01

...— (1) Have steel walls of a minimum 3/16-inch thickness, or walls made of other metal of a thickness that provides equivalent strength; (2) Be protected from corrosion; (3) Be of seamless construction or...

30 CFR 75.1904 - Underground diesel fuel tanks and safety cans.

Code of Federal Regulations, 2013 CFR

2013-07-01

...— (1) Have steel walls of a minimum 3/16-inch thickness, or walls made of other metal of a thickness that provides equivalent strength; (2) Be protected from corrosion; (3) Be of seamless construction or...

49 CFR 238.223 - Locomotive fuel tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... an industry standard providing at least an equivalent level of safety if approved by FRA under § 238..., at a minimum, be equivalent to a 5/16-inch thick steel plate with a yield strength of 25,000 pounds...

Weld Metallurgy and Mechanical Properties of High Manganese Ultra-high Strength Steel Dissimilar Welds

NASA Astrophysics Data System (ADS)

Dahmen, Martin; Lindner, Stefan; Monfort, Damien; Petring, Dirk

The increasing demand for ultra-high strength steels in vehicle manufacturing leads to the application of new alloys. This poses a challenge on joining especially by fusion welding. A stainless high manganese steel sheet with excellent strength and deformation properties stands in the centre of the development. Similar and dissimilar welds with a metastable austenitic steel and a hot formed martensitic stainless steel were performed. An investigation of the mixing effects on the local microstructure and the hardness delivers the metallurgical features of the welds. Despite of carbon contents above 0.4 wt.% none of the welds have shown cracks. Mechanical properties drawn from tensile tests deliver high breaking forces enabling a high stiffness of the joints. The results show the potential for the application of laser beam welding for joining in assembly of structural parts.

Fatigue limits of titanium-bar joints made with the laser and the electric resistance welding techniques: microstructural characterization and hardness properties.

PubMed

Degidi, Marco; Nardi, Diego; Morri, Alessandro; Sighinolfi, Gianluca; Tebbel, Florian; Marchetti, Claudio

2017-09-01

Fatigue behavior of the titanium bars is of utmost importance for the safe and reliable operation of dental implants and prosthetic constructions based on these implants. To date, however, only few data are available on the fatigue strength of dental prostheses made with electric resistance welding and laser welding techniques. This in-vitro study highlighted that although the joints made with the laser welding approach are credited of a superior tensile strength, joints made with electric resistance welding exhibited double the minimum fatigue strength with respect to the joints made with laser welding (120 vs 60 N).

Optimal estimation of the optomechanical coupling strength

NASA Astrophysics Data System (ADS)

Bernád, József Zsolt; Sanavio, Claudio; Xuereb, André

2018-06-01

We apply the formalism of quantum estimation theory to obtain information about the value of the nonlinear optomechanical coupling strength. In particular, we discuss the minimum mean-square error estimator and a quantum Cramér-Rao-type inequality for the estimation of the coupling strength. Our estimation strategy reveals some cases where quantum statistical inference is inconclusive and merely results in the reinforcement of prior expectations. We show that these situations also involve the highest expected information losses. We demonstrate that interaction times on the order of one time period of mechanical oscillations are the most suitable for our estimation scenario, and compare situations involving different photon and phonon excitations.

The dynamic properties behavior of high strength concrete under different strain rate

NASA Astrophysics Data System (ADS)

Abdullah, Hasballah; Husin, Saiful; Umar, Hamdani; Rizal, Samsul

2005-04-01

This paper present a number experimental data and numerical technique used in the dynamic behavior of high strength concrete. A testing device is presented for the experimental study of dynamic behavior material under high strain rates. The specimen is loaded by means of a high carbon steel Hopkinson pressure bar (40 mm diameter, 3000 mm long input bar and 1500 mm long out put bar) allowing for the testing of specimen diameter is large enough in relation to the size of aggregates. The other method also proposed for measuring tensile strength, the measurement method based on the superposition and concentration of tensile stress wave reflected both from the free-free ends of striking bar and the specimen bar. The compression Hopkinson bar test, the impact tensile test of high strength concrete bars are performed, together with compression static strength test. In addition, the relation between break position under finite element simulation and impact tensile strength are examined. The three-dimensional simulation of the specimen under transient loading are presented and comparisons between the experimental and numerical simulation on strain rate effects of constitutive law use in experimental are study.

Electrical Breakdown in Water Vapor

NASA Astrophysics Data System (ADS)

Škoro, N.; Marić, D.; Malović, G.; Graham, W. G.; Petrović, Z. Lj.

2011-11-01

In this paper investigations of the voltage required to break down water vapor are reported for the region around the Paschen minimum and to the left of it. In spite of numerous applications of discharges in biomedicine, and recent studies of discharges in water and vapor bubbles and discharges with liquid water electrodes, studies of the basic parameters of breakdown are lacking. Paschen curves have been measured by recording voltages and currents in the low-current Townsend regime and extrapolating them to zero current. The minimum electrical breakdown voltage for water vapor was found to be 480 V at a pressure times electrode distance (pd) value of around 0.6 Torr cm (˜0.8 Pa m). The present measurements are also interpreted using (and add additional insight into) the developing understanding of relevant atomic and particularly surface processes associated with electrical breakdown.

12 mJ Yb:YAG/Cr:YAG microchip laser

NASA Astrophysics Data System (ADS)

Guo, Xiaoyang; Tokita, Shigeki; Kawanaka, Junji

2018-02-01

By cryogenically cooling the Yb:YAG/Cr:YAG medium, one can break through the damage limit of Yb:YAG/Cr:YAG passively Q-switched microchip lasers at room temperature and thus achieve a shorter minimum pulse duration. In the proof of principle experiment we carried out, a 160.6 ps pulse duration was obtained. To the best of our knowledge, this is the first realization of sub-200 ps pulse operation for an Yb:YAG/Cr:YAG microchip laser

Probabilistically Perfect Cloning of Two Pure States: Geometric Approach.

PubMed

Yerokhin, V; Shehu, A; Feldman, E; Bagan, E; Bergou, J A

2016-05-20

We solve the long-standing problem of making n perfect clones from m copies of one of two known pure states with minimum failure probability in the general case where the known states have arbitrary a priori probabilities. The solution emerges from a geometric formulation of the problem. This formulation reveals that cloning converges to state discrimination followed by state preparation as the number of clones goes to infinity. The convergence exhibits a phenomenon analogous to a second-order symmetry-breaking phase transition.

Increase of tensile strength and toughness of bio-based diglycidyl ether of bisphenol A with chitin nanowhiskers

PubMed Central

Wang, Mian; Xue, Han; Feng, Zhiwei; Cheng, Binfeng; Yang, Haijie

2017-01-01

It is challenging to reinforce and toughen thermoset epoxy resins. We describe a slurry-compounding technique to transfer a uniform dispersion of chitin nanowhiskers (CW) in ethanol into an epoxy matrix. The incorporation of the hydrophilic CW reinforces the oil-soluble diglycidyl ether of bisphenol A (DGEBA). The resultant CW/epoxy bionanocomposites were transparent and showed considerably enhanced thermal and mechanical properties with tensile strength, modulus, toughness, and elongation at break being increased by 49%, 16%, 457%, and 250%, with only 2.5 wt.% CW. This improvement in strength and toughness is rare for thermoset epoxy/rigid nanofiller systems. We hypothesize that CW with many free amine groups could function not only as a nanofiller but also as a macromolecular polyamine hardener that participates in epoxy curing. The strong covalent interaction between the filler and the matrix allowed for efficient load transfer across the interfaces, which accounted for the greater strength and toughness. PMID:28604774

Transverse stresses and modes of failure in tree branches and other beams.

PubMed

Ennos, A R; van Casteren, A

2010-04-22

The longitudinal stresses in beams subjected to bending also set up transverse stresses within them; they compress the cross section when the beam's curvature is being increased and stretch it when its curvature is being reduced. Analysis shows that transverse stresses rise to a maximum at the neutral axis and increase with both the bending moment applied and the curvature of the beam. These stresses can qualitatively explain the fracture behaviour of tree branches. Curved 'hazard beams' that are being straightened split down the middle because of the low transverse tensile strength of wood. By contrast, straight branches of light wood buckle when they are bent because of its low transverse compressive strength. Branches of denser wood break, but the low transverse tensile strength diverts the crack longitudinally when the fracture has only run half-way across the beam, to produce their characteristic 'greenstick fracture'. The bones of young mammals and uniaxially reinforced composite beams may also be prone to greenstick fracture because of their lower transverse tensile strength.

Effects of Sintering and Extrusion on the Microstructures and Mechanical Properties of a SiC/Al-Cu Composite

NASA Astrophysics Data System (ADS)

Sun, Chao; Shen, Rujuan; Song, Min

2012-03-01

This article studied the effects of sintering and extrusion on the microstructures and mechanical properties of SiC particle reinforced Al-Cu alloy composite produced by powder metallurgy method. It has been shown that both extrusion and increasing sintering temperature can significantly improve the strength and plasticity of the composite. The extrusion and increase of the sintering temperature can break up the oxide coating on the matrix powder surfaces, decrease the number of pores, accelerate the elements' diffusion and increase the density and particle interfacial bonding strength, thus significantly improve the mechanical properties of the composite. The strength and hardness of the composite increase and the elongation decreases with increasing the aging time at under-aged stage, while the strength and hardness start to decrease and the elongation starts to increase with increasing the aging time at over-aged stage due to the formation and growth of the secondary strengthening precipitates in the Al-Cu matrix.

Increase of tensile strength and toughness of bio-based diglycidyl ether of bisphenol A with chitin nanowhiskers.

PubMed

Wang, Mian; Xue, Han; Feng, Zhiwei; Cheng, Binfeng; Yang, Haijie

2017-01-01

It is challenging to reinforce and toughen thermoset epoxy resins. We describe a slurry-compounding technique to transfer a uniform dispersion of chitin nanowhiskers (CW) in ethanol into an epoxy matrix. The incorporation of the hydrophilic CW reinforces the oil-soluble diglycidyl ether of bisphenol A (DGEBA). The resultant CW/epoxy bionanocomposites were transparent and showed considerably enhanced thermal and mechanical properties with tensile strength, modulus, toughness, and elongation at break being increased by 49%, 16%, 457%, and 250%, with only 2.5 wt.% CW. This improvement in strength and toughness is rare for thermoset epoxy/rigid nanofiller systems. We hypothesize that CW with many free amine groups could function not only as a nanofiller but also as a macromolecular polyamine hardener that participates in epoxy curing. The strong covalent interaction between the filler and the matrix allowed for efficient load transfer across the interfaces, which accounted for the greater strength and toughness.

Statistical mechanical analysis of linear programming relaxation for combinatorial optimization problems

NASA Astrophysics Data System (ADS)

Takabe, Satoshi; Hukushima, Koji

2016-05-01

Typical behavior of the linear programming (LP) problem is studied as a relaxation of the minimum vertex cover (min-VC), a type of integer programming (IP) problem. A lattice-gas model on the Erdös-Rényi random graphs of α -uniform hyperedges is proposed to express both the LP and IP problems of the min-VC in the common statistical mechanical model with a one-parameter family. Statistical mechanical analyses reveal for α =2 that the LP optimal solution is typically equal to that given by the IP below the critical average degree c =e in the thermodynamic limit. The critical threshold for good accuracy of the relaxation extends the mathematical result c =1 and coincides with the replica symmetry-breaking threshold of the IP. The LP relaxation for the minimum hitting sets with α ≥3 , minimum vertex covers on α -uniform random graphs, is also studied. Analytic and numerical results strongly suggest that the LP relaxation fails to estimate optimal values above the critical average degree c =e /(α -1 ) where the replica symmetry is broken.

An explanation for the tiny value of the cosmological constant and the low vacuum energy density

NASA Astrophysics Data System (ADS)

Nassif, Cláudio

2015-09-01

The paper aims to provide an explanation for the tiny value of the cosmological constant and the low vacuum energy density to represent the dark energy. To accomplish this, we will search for a fundamental principle of symmetry in space-time by means of the elimination of the classical idea of rest, by including an invariant minimum limit of speed in the subatomic world. Such a minimum speed, unattainable by particles, represents a preferred reference frame associated with a background field that breaks down the Lorentz symmetry. The metric of the flat space-time shall include the presence of a uniform vacuum energy density, which leads to a negative pressure at cosmological length scales. Thus, the equation of state for the cosmological constant [ p(pressure) (energy density)] naturally emerges from such a space-time with an energy barrier of a minimum speed. The tiny values of the cosmological constant and the vacuum energy density will be successfully obtained, being in agreement with the observational results of Perlmutter, Schmidt and Riess.

Statistical mechanical analysis of linear programming relaxation for combinatorial optimization problems.

PubMed

Takabe, Satoshi; Hukushima, Koji

2016-05-01

Typical behavior of the linear programming (LP) problem is studied as a relaxation of the minimum vertex cover (min-VC), a type of integer programming (IP) problem. A lattice-gas model on the Erdös-Rényi random graphs of α-uniform hyperedges is proposed to express both the LP and IP problems of the min-VC in the common statistical mechanical model with a one-parameter family. Statistical mechanical analyses reveal for α=2 that the LP optimal solution is typically equal to that given by the IP below the critical average degree c=e in the thermodynamic limit. The critical threshold for good accuracy of the relaxation extends the mathematical result c=1 and coincides with the replica symmetry-breaking threshold of the IP. The LP relaxation for the minimum hitting sets with α≥3, minimum vertex covers on α-uniform random graphs, is also studied. Analytic and numerical results strongly suggest that the LP relaxation fails to estimate optimal values above the critical average degree c=e/(α-1) where the replica symmetry is broken.

Does Cervical Interlaminar Epidural Steroid Injection with Low-Dose Lidocaine Cause Objective Upper Extremity Weakness? A Preliminary Study.

PubMed

McCormick, Zachary L; Nelson, Ariana; Kendall, Mark C; McCarthy, Robert J; Nagpal, Geeta; Walega, David R

2017-12-01

Low-dose local anesthetic is often used in cervical interlaminar epidural steroid injections (CIESI), yet its effect on upper extremity strength has not been studied. The presence of consequent weakness has potential implications for postprocedure safety. This study aimed to determine whether low-dose lidocaine in a C7-T1 CIESI causes objective weakness. Prospective case series. Academic pain center. Adults, cervical radicular pain. Participants underwent CIESI with 1 mL of 1% lidocaine (3 mL total injectate). Elbow flexion (EF), wrist extension (WE), elbow extension (EE), and handgrip strength were measured by dynamometry at baseline, 15 minutes, and 30 minutes postinjection. Changes in strength from baseline and the proportion of participants with a minimum perceptible change in EF, WE, EE, and handgrip strength (≥20%) and 95% confidence intervals (CIs) were calculated. Twenty-seven participants were included. At 15 and 30 minutes postinjection, there was no within-participant difference in EF, WE, EE, and handgrip strength from baseline overall. Nonetheless, five (19%, 95% CI = 4-33) of the participants demonstrated a 20% or greater strength decrease in at least one myotomal distribution. A 20% or greater decrease in strength was present in left EF 4% (95% CI = 0-11%), right EF 7% (95% CI = 0-17%), left WE 4% (95% CI = 0-11%), and right WE 7% (95% CI = 0-17%). The present data suggest that CIESI with an injectate volume of 3 mL that includes 1 mL of 1% lidocaine may result in objective upper extremity weakness that is above the minimum threshold of perception in a subset of patients. © 2017 American Academy of Pain Medicine. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

The strength of metal matrix composites

NASA Astrophysics Data System (ADS)

Baxter, William J.

1992-11-01

There is intensive interest in metal matrix composites (MMCs) for automotive components, and the first production applications in Japan use discontinuous fibers as the reinforcements. These fibers are randomly oriented, resulting in an MMC with isotropic properties. However, there are conflicting reports on the tensile strengths attainable. In some cases, the strength increases with increasing volume fraction (V f) of fibers, while in other cases, there is little or no benefit. A simple method is proposed to calculate the strength of this type of MMC. It is shown that the fibers oriented perpendicular to the stress direction play a key role, and the strength depends upon the strength of the interfacial bond. Upper and lower limits of the composite strength are calculated. If the bond strength is larger than the matrix strength, the composite strength has a maximum value which increases with V f. If the bond strength is weaker than the matrix, the composite strength has a minimum value which is either weakly dependent or even independent of V f. These calculations are in good agreement with examples taken from the literature of aluminum composites reinforced with either A12O3, graphite, or SiC. The strength of the matrix alloy is shown to be a very important parameter: weak alloys are easily strengthened, while in certain cases, strong alloys may be weakened.

General and mechanistic optimal relationships for tensile strength of doubly convex tablets under diametrical compression.

PubMed

Razavi, Sonia M; Gonzalez, Marcial; Cuitiño, Alberto M

2015-04-30

We propose a general framework for determining optimal relationships for tensile strength of doubly convex tablets under diametrical compression. This approach is based on the observation that tensile strength is directly proportional to the breaking force and inversely proportional to a non-linear function of geometric parameters and materials properties. This generalization reduces to the analytical expression commonly used for flat faced tablets, i.e., Hertz solution, and to the empirical relationship currently used in the pharmaceutical industry for convex-faced tablets, i.e., Pitt's equation. Under proper parametrization, optimal tensile strength relationship can be determined from experimental results by minimizing a figure of merit of choice. This optimization is performed under the first-order approximation that a flat faced tablet and a doubly curved tablet have the same tensile strength if they have the same relative density and are made of the same powder, under equivalent manufacturing conditions. Furthermore, we provide a set of recommendations and best practices for assessing the performance of optimal tensile strength relationships in general. Based on these guidelines, we identify two new models, namely the general and mechanistic models, which are effective and predictive alternatives to the tensile strength relationship currently used in the pharmaceutical industry. Copyright © 2015 Elsevier B.V. All rights reserved.

Polariton solitons and nonlinear localized states in a one-dimensional semiconductor microcavity

NASA Astrophysics Data System (ADS)

Chen, Ting-Wei; Cheng, Szu-Cheng

2018-01-01

This paper presents numerical studies of cavity polariton solitons (CPSs) in a resonantly pumped semiconductor microcavity with an imbedded spatial defect. In the bistable regime of the well-known homogeneous polariton condensate, with proper incident wave vector and pump strength, bright and/or dark cavity solitons can be found in the presence of a spatially confined potential. The minimum pump strength required to observe the CPSs or nonlinear localized states in this parametric pump scheme is therefore reported.

Optical Boron Nitride Insulator Erosion Characterization of a 200 W Xenon Hall Thruster

DTIC Science & Technology

2005-05-01

Hall thruster boron nitride insulator is evaluated as a diagnostic for real-time evaluation of thruster insulator erosion. Three Hall thruster plasma control variables are examined: ion energy (discharge potential), ion flux (propellant flow), and plasma conductivity (magnetic field strength). The boron emission, and hence the insulator erosion rate, varies linearly with ion energy and ion flux. A minimum erosion rate appears at intermediate magnetic field strengths. This may indicate that local plasma conductivity significantly affects the divergence

Suppression of Growth by Multiplicative White Noise in a Parametric Resonant System

NASA Astrophysics Data System (ADS)

Ishihara, Masamichi

2015-02-01

The growth of the amplitude in a Mathieu-like equation with multiplicative white noise is studied. To obtain an approximate analytical expression for the exponent at the extremum on parametric resonance regions, a time-interval width is introduced. To determine the exponents numerically, the stochastic differential equations are solved by a symplectic numerical method. The Mathieu-like equation contains a parameter α determined by the intensity of noise and the strength of the coupling between the variable and noise; without loss of generality, only non-negative α can be considered. The exponent is shown to decrease with α, reach a minimum and increase after that. The minimum exponent is obtained analytically and numerically. As a function of α, the minimum at α≠0, occurs on the parametric resonance regions of α=0. This minimum indicates suppression of growth by multiplicative white noise.

Behavior modification after inactivation of cerebellar dentate nuclei.

PubMed

Peterson, Todd C; Villatoro, Lee; Arneson, Tom; Ahuja, Brittany; Voss, Stephanie; Swain, Rodney A

2012-08-01

Effort-based decision making occurs when subjects are given a choice between a reward available at a high response cost and a reward available at a low response cost and is altered in individuals with disorders such as autism or particular patterns of brain injury. The current study explored the relationship between effort-based decision making and reinforcement characteristics in the T maze. This was done using both normal animals and animals with bilateral inactivation of the cerebellar dentate nuclei. Rats chose between alternatives in which one arm contained high-density reinforcement (HR) and the other arm contained low-density reinforcement (LR). During training, the HR arm was obstructed and the point at which the animal no longer worked for reinforcement (breaking point) was determined. The cerebellar dentate nuclei were then transiently inactivated and once again breaking points were assessed. The results indicated that inactivation of the dentate nucleus disrupted effort-based decision making. Additionally, altering both the palatability and the magnitude of the reinforcement were assessed in an attempt to reestablish the original preinactivation breaking point. It was hypothesized that an increase in the strength or magnitude of the reinforcement would promote an increase in the breaking point of the animal even when the cerebellum was inactivated. The results indicated that with both strategies animals effectively reestablished original breaking points. The results of this study will inform the current literature regarding the modification of behavior after brain injury and further the understanding of the behavioral deficits associated with cerebellar dysfunction.

Coherent Structures and Evolution of Vorticity in Short-Crested Breaking Surface Waves

NASA Astrophysics Data System (ADS)

Kirby, James; Derakhti, Morteza

2017-11-01

We employ a multi-phase LES/VOF code to study turbulence and coherent structures generated during breaking of short-crested surface water waves. We examine the evolution of coherent vortex structures evolving at the scale of the width of the breaking event, and their long-time interaction with smaller vortex loops formed by the local instability of the breaking crest. Long-time results are often characterized by the detachment of the larger scale vortex loop from the surface and formation of a closed vortex ring. The evolution of circulation for the vortical flow field is examined. The initial concentration of forcing close to the free surface leads to spatial distributions of both span-wise and vertical vorticity distributions which are concentrated close to the surface. This result, which persists into shallow water, is at odds with the basic simplicity of the Peregrine mechanism, suggesting that even shallow flows such as the surf zone should be regarded as being forced (in dissipative situations) by a wave-induced surface stress rather than a uniform-over-depth body force. The localized forcing leads to the development of a complex pattern of stream-wise vorticity, comparable in strength to the vertical and span-wise components, and also persist into shallow water. NSF OCE-1435147.

Mechanical properties of direct core build-up materials.

PubMed

Combe, E C; Shaglouf, A M; Watts, D C; Wilson, N H

1999-05-01

This work was undertaken to measure mechanical properties of a diverse group of materials used for direct core build-ups, including a high copper amalgam, a silver cermet cement, a VLC resin composite and two composites specifically developed for this application. Compressive strength, elastic modulus, diametral tensile strength and flexural strength and modulus were measured for each material as a function of time up to 3 months, using standard specification tests designed for the materials. All the materials were found to meet the minimum specification requirements except in terms of flexural strength for the amalgam after 1 h and the silver cermet at all time intervals. There proved to be no obvious superior material in all respects for core build-ups, and the need exists for a specification to be established specifically for this application.

Homogeneity of Mechanical Properties of Underwater Friction Stir Welded 2219-T6 Aluminum Alloy

NASA Astrophysics Data System (ADS)

Liu, H. J.; Zhang, H. J.; Yu, L.

2011-11-01

Underwater friction stir welding (FSW) has been demonstrated to be available for the improvement in tensile strength of normal FSW joints. In order to illuminate the intrinsic reason for strength improvement through underwater FSW, a 2219 aluminum alloy was underwater friction stir welded and the homogeneity of mechanical properties of the joint was investigated by dividing the joint into three layers. The results indicate that the tensile strength of the three layers of the joint is all improved by underwater FSW, furthermore, the middle and lower layers have larger extent of strength improvement than the upper layer, leading to an increase in the homogeneity of mechanical properties of the joint. The minimum hardness value of each layer, especially the middle and lower layers, is improved under the integral water cooling effect, which is the intrinsic reason for the strength improvement of underwater joint.