Composite strengthening. [of nonferrous, fiber reinforced alloys

NASA Technical Reports Server (NTRS)

Stoloff, N. S.

1976-01-01

The mechanical behavior of unidirectionally reinforced metals is examined, with particular attention to fabrication techniques for artificial composites and eutectic alloys and to principles of fiber reinforcement. The properties of artificial composites are discussed in terms of strength of fiber composites, strength of ribbon-reinforced composites, crack initiation, crack propagation, and creep behavior. The properties of eutectic composites are examined relative to tensile strength, compressive strength, fracture, high-temperature strength, and fatigue. In the case of artificial composites, parallelism of fibers, good bonding between fibers and matrix, and freedom of fibers from damage are all necessary to ensure superior performance. For many eutectic systems there are stringent boundary conditions relative to melt purity and superheat, atmosphere control, temperature gradient, and growth rate in order to provide near-perfect alignment of the reinforcements with a minimum of growth defects.

Redox equilibria and the structural role of iron in alumino-silicate melts

NASA Astrophysics Data System (ADS)

Dickenson, M. P.; Hess, P. C.

1982-01-01

The relationship between the redox ratio Fe+2/(Fe+2+Fe+3) and the K2O/(K2O + Al2O3) ratio (K2O*) were experimentally investigated in silicate melts with 78 mol% SiO2 in the system SiO2-Al2O3-K2O-FeO-Fe2O3, in air at 1,400° C. Quenched glass compositions were analyzed by electron microprobe and wet chemical microtitration techniques. Minimum values of the redox ratio were obtained at K2O*≈0.5. The redox ratio in peralkaline melts (K2O*>0.5) increases slightly with K2O* whereas this ratio increases dramatically in peraluminous melts (K2O*<0.5) as K2O is replaced by Al2O3. These data indicate that all Fe+3 (and Al+3) occur as tetrahedral species charge balanced with K+ in peralkaline melts. In peraluminous melts, Fe+3 (and Al+3) probably occur as both tetrahedral species using Fe+2 as a charge-balancing cation and as network-modifying cations associated with non-bridging oxygen.

Fluorine and the viscosity of jadeite-leucite and nepheline-kalsilite melts at atmospheric pressure

NASA Astrophysics Data System (ADS)

Robert, G.; Bruno, M.; Carty, O.; Smith, R. A.; Whittington, A. G.

2017-12-01

While fluorine has a lower abundance than H2O and CO2 in most magmatic and volcanic systems, F is as effective as water at reducing the viscosity of silica-rich melts. Previous studies have also shown that, just like water, the effect of F in reducing melt viscosity is strongest in the most highly polymerized melts. We measured the viscosity of fluorine-free and fluorine-bearing melts along the jadeite-leucite (Jd-Lct) and nepheline-kalsilite (Ne-Kls) joins of the NaAlSiO4-KAlSiO4-SiO2 system. All compositions studied are metaluminous to slightly peraluminous, and nominally fully polymerized (noting that non-bridging oxygen sites exist in metaluminous and peraluminous glasses, their proportion being a function of Al/Si ratio and cation charge). We test whether the effects of fluorine on viscosity have a dependence on Na/K or Al/Si ratios in these melts. In fluorine-free melts, the K-rich melts have the highest viscosity and T12 (temperature of the 1012 Pas isokom). The mixed-alkali effect results in a viscosity minimum at compositions with intermediate Na/K ratios. At 1200K, for the Na- end-member melts, the lowest Al/Si ratio melts (nepheline-kalsilite melts) have the highest viscosity. Available literature data and extrapolation of trends from our measurements suggest there is little difference in viscosity between the K- end-member melts at 1200K. At high temperatures, the jadeite-leucite melts generally have higher viscosities than the nepheline-kalsilite melts. Fluorine reduces the viscosity of all of the melts we studied, and, although it has been suggested that fluorine preferentially bonds with potassium over sodium, its effects on viscosity appears to be approximately independent of Na/K ratio in metaluminous melts. With increasing Al/Si ratio, more order is required to satisfy the aluminum avoidance principle, but this also does not seem to affect the magnitude of viscosity reduction due to the addition of fluorine, at least for melts with intermediate Na/K ratio. Adding 8 mol% F to melts with Na/(Na+K) ratio of 0.5 results in a T12 reduction of 186°C relative to F-free melts.

Processes active in mafic magma chambers: The example of Kilauea Iki Lava Lake, Hawaii

USGS Publications Warehouse

Helz, R.T.

2009-01-01

Kilauea Iki lava lake formed in 1959 as a closed chamber of 40??million m3 of picritic magma. Repeated drilling and sampling of the lake allows recognition of processes of magmatic differentiation, and places time restrictions on the periods when they operated. This paper focuses on evidence for the occurrence of lateral convection in the olivine-depleted layer, and constraints on the timing of this process, as documented by chemical, petrographic and thermal data on drill core from the lake. Lateral convection appears to have occurred in two distinct layers within the most olivine-poor part of the lake, created a slightly olivine-enriched septum in the center of the olivine-depleted section. A critical marker for this process is the occurrence of loose clusters of augite microphenocrysts, which are confined to the upper half of the olivine-poor zone. This process, which took place between late 1962 and mid-1964, is inferred to be double-diffusive convection. Both this convection and a process of buoyant upwelling of minimum-density liquid from deep within the lake (Helz, R.T., Kirschenbaum H. and Marinenko, J.W., 1989. Diapiric melt transfer: a quick, efficient process of igneous differentiation: Geological Society of America Bulletin, v. 101, 578-594) result from the fact that melt density in Kilauea Iki compositions decreases as olivine and augite crystallize, above the incoming of plagioclase. The resulting density vs. depth profile creates (1) a region of gravitationally stable melt at the top of the chamber (the locus of double-diffusive convection) and (2) a region of gravitationally unstable melt at the base of the melt column (the source of upwelling minimum-density melt, Helz, R.T., Kirschenbaum H. and Marinenko, J.W., 1989. Diapiric melt transfer: a quick, efficient process of igneous differentiation: Geological Society of America Bulletin, v. 101, 578-594). By contrast the variation of melt density with temperature for the 1965 Makaopuhi lava lake does not show a decrease in density as temperature decreases, so neither process should have occurred in that lava lake. Because many mafic magmas crystallize significant olivine and/or pyroxene before they begin to crystallize plagioclase, the density relations observed for Kilauea Iki, and the processes that result from them, may be relevant to crystallization in other mafic magma chambers. The results for the 1965 Makaopuhi lava lake emphasize the role of bulk composition as a critical control on magmatic processes.

Melt inclusion evidence for the relative timing of assimilation and crystallisation in high MgO lavas, Mull, Scotland

NASA Astrophysics Data System (ADS)

Peate, D. W.; Ukstins Peate, I.; Rowe, M. C.; Thompson, J. M.; Kerr, A. C.

2010-12-01

Whole rock data on the Mull Plateau Group lavas (Scotland) show that the most primitive lavas (MgO >8 wt%) are the most crustally contaminated. One model is that hot, high-MgO magmas flow turbulently during ascent allowing more assimilation to occur than in the laminar flow regime expected for cooler, more viscous, lower-MgO magmas. We present data on rehomogenized olivine-hosted melt inclusions from four representative high-MgO flows to investigate the nature of the assimilation process in more detail. One complication on Mull is the potential effect of pervasive hydrothermal metamorphism on whole rock compositions. Melt inclusions are more protected against alteration effects within their host olivine crystal, and potentially allow more robust estimates of magmatic liquid compositions. Low sulphur contents were used to screen for degassed / breached inclusions, and the compositions of unbreached inclusions were corrected for post-entrapment crystallisation and Fe-loss. The four whole rock samples show a limited variation in Na2O (2.4-2.8 wt%) and K2O (0.23-0.29 wt%) despite a wide range in immobile element contents (e.g. Zr 62-126 ppm, Nb 2.4-4.6 ppm). In contrast, the melt inclusions show a far greater variability in Na2O (1.8-4.0 wt%) and K2O (0.02-0.35 wt%) and coherent positive correlations between K and Na. Melt inclusions from different samples show systematic correlations between alkalis (K+Na) and incompatible element ratios such as Zr/Y and La/Sm, indicating that the melt inclusions are recording magmatic values for fluid mobile elements such as K and Na. For the two most incompatible element enriched samples, the whole rock analysis is similar to the melt inclusions except for lower Na and higher Ba that are related to alteration. Therefore, any crustal assimilation in these magmas must have take place prior to the growth of the olivines in the samples. For the two more depleted samples, the melt inclusions have less contaminated compositions than the whole rocks, and also show broad trends of increasing K/Ti (extent of assimilation) with decreasing Fo% of the host olivine (extent of differentiation). For these samples, significant crustal assimilation must have taken place both during and after growth of the olivines in the samples. Melt inclusions from individual samples show limited variability in Zr/Y compared with K/Ti, indicating that aggregation of melts from different parts of the melting column must have occurred at deeper levels prior to growth of the olivines in the samples. Reconnaissance H2O and CO2 analyses by SIMS allow estimates to be made of minimum inclusion entrapment depths of at least 3 to 7 km. Although it is apparent that whole rock compositional variations still capture the broad details of crustal assimilation and melting histories for Mull lavas despite the variable effects of hydrothermal alteration, we demonstrate that melt inclusion data can more clearly resolve details of these magmatic processes.

Phase relations in the system NaCl-KCl-H2O. Part I: Differential thermal analysis of the NaCl-KCl liquidas at 1 atmosphere and 500, 1000, 1500, and 2000 bars

USGS Publications Warehouse

Chou, I.-Ming

1982-01-01

A simple differential thermal analysis (DTA) technique has been developed to study phase relations of various chemical systems at elevated pressures and temperatures. The DTA system has been calibrated against known melting temperatures in the system NaCl-KCl. Isobaric sections of the liquidus in the system NaCl-KCl have been determined at pressures of 1 atmosphere and 500, 1000, 1500, and 2000 bars. Using the least-squares method, the following equation was used to fit the experimental data: T(??C)= ??? i=0 6aiXiKCl where T is the liquidus temperature, XKCl is mole fraction of KCl, and ai (listed below) are the derived empirical constants. {A table is presented}. The liquidus temperatures estimated from these equations are within ??3??C of experimental values. The measured liquidus temperatures at 1 atmosphere agree with the best available data to within 5??C. The melting temperatures for pure end members at higher pressures agree with the values calculated from the Simon equation (Clark, 1959) to within 3??C. No previous melting data are available for the intermediate compositions at elevated pressures. Using the data in both heating and cooling scans, the minimum melting temperature at 1 atmosphere in the system was located at 658?? ?? 3??C where the sample has an equimolar composition. ?? 1982.

The Phillips pluton, Maine, USA: evidence of heterogeneous crustal sources and implications for granite ascent and emplacement mechanisms in convergent orogens

NASA Astrophysics Data System (ADS)

Pressley, Rachel A.; Brown, Michael

1999-03-01

The Phillips pluton (age of 403.8±1.3 Ma) was assembled at a crustal level below the contemporary brittle-plastic transition during regional dextral-reverse transpressive deformation. The pluton is composed dominantly of medium- to coarse-grained leucogranite sensu lato (s.l.), but within its bounds includes decametric massive outcrop of fine- to medium-grained granodiorite (s.l.). In places, the leucogranite contains centimetric enclaves apparently of the granodiorite. Granodiorite is host to more biotite than muscovite, and more calcic, oscillatory-zoned plagioclase, compared to the leucogranite. Pegmatitic granite and composite pegmatite-aplite occur as metric sheets within the pluton and as larger bodies outside the pluton to the SW. Magmatic fabrics, defined by biotite schlieren, occur locally in the leucogranite; the attitude of these fabrics and layering within the leucogranite are concordant with the NE-striking, steeply-dipping country rock foliation. K 2O contents, Rb/Sr ratios, Rb, Sr and Ba covariations, and chondrite-normalized rare earth element (REE) patterns of leucogranite are consistent with high-to-moderate a(H 2O) muscovite dehydration equilibrium eutectic melting of a predominantly pelite source similar to metasedimentary rocks of the surrounding central Maine belt (CMB). The REE patterns and Rb/Sr ratios of granodiorite also suggest derivation from a metasedimentary source, but more likely by moderate-to-low a(H 2O) (muscovite-) biotite dehydration equilibrium eutectic to non-eutectic (minimum) melting of a protolith dominated by greywacke in which garnet and plagioclase were residual phases. Both granite (s.l.) types have heterogeneous initial Nd isotope compositions. Samples of granodiorite define a range in ɛNd (404 Ma) of -1.8 to +0.1 (±0.3 2 σ uncertainty), and samples of leucogranite define a range in ɛNd (404 Ma) of -8.0 to -5.3 (±0.3 2 σ uncertainty). This bimodal distribution suggests that melts were derived from a minimum of two sources. The data are consistent with these sources being CMB metasedimentary rocks ( ɛNd (404 Ma)<-4) for the leucogranite, and Avalon-like (peri-Gondwanan) metasedimentary crust ( ɛNd (404 Ma)>-4) for the granodiorite. The range of Nd isotope compositions within each granite type most likely reflects isotopic heterogeneity inherited from the source. These data imply that the integrity of individual melt batches was maintained during ascent, and that extensive mixing of melt batches during emplacement at this level in the pluton did not occur, although centimetric enclaves have intermediate Nd isotope compositions consistent with small-scale interactions between magmas. We infer that the Phillips pluton represents the root of a larger pluton, and that what remains of this larger pluton is the feeder constructed from multiple melt batches arrested during waning flow of granite magma through a crustal-scale shear zone system.

Melting relations in the iron-sulfur system at ultra-high pressures - Implications for the thermal state of the earth

NASA Technical Reports Server (NTRS)

Williams, Quentin; Jeanloz, Raymond

1990-01-01

The melting temperatures of FeS-troilite and of a 10-wt-pct sulfur iron alloy have been measured to pressures of 120 and 90 GPa, respectively. The results document that FeS melts at a temperature of 4100 (+ or - 300) K at the pressure of the core-mantle boundary. Eutecticlike behavior persists in the iron-sulfur system to the highest pressures of measurements, in marked contrast to the solid-solutionlike behavior observed at high pressures in the iron-iron oxide system. Iron with 10-wt-pct sulfur melts at a similar temperature as FeS at core-mantle boundary conditions. If the sole alloying elements of iron within the core are sulfur and oxygen and the outer core is entirely liquid, the minimum temperature at the top of the outer core is 4900 (+ or - 400) K. Calculations of mantle geotherms dictate that there must be a temperature increase of between 1000 and 2000 K across thermal boundary layers within the mantle. If D-double-prime is compositionally stratified, it could accommodate the bulk of this temperature jump.

Water solubility in aluminous orthopyroxene and the origin of Earth's asthenosphere.

PubMed

Mierdel, Katrin; Keppler, Hans; Smyth, Joseph R; Langenhorst, Falko

2007-01-19

Plate tectonics is based on the concept of rigid lithosphere plates sliding on a mechanically weak asthenosphere. Many models assume that the weakness of the asthenosphere is related to the presence of small amounts of hydrous melts. However, the mechanism that may cause melting in the asthenosphere is not well understood. We show that the asthenosphere coincides with a zone where the water solubility in mantle minerals has a pronounced minimum. The minimum is due to a sharp decrease of water solubility in aluminous orthopyroxene with depth, whereas the water solubility in olivine continuously increases with pressure. Melting in the asthenosphere may therefore be related not to volatile enrichment but to a minimum in water solubility, which causes excess water to form a hydrous silicate melt.

Bromine partitioning between olivine and melt at OIB source conditions: Indication for volatile recycling

NASA Astrophysics Data System (ADS)

Joachim, Bastian; Ruzié, Lorraine; Burgess, Ray; Pawley, Alison; Clay, Patricia L.; Ballentine, Christopher J.

2016-04-01

Halogens play a key role in our understanding of volatile transport processes in the Earth's mantle. Their moderate (fluorine) to highly (iodine) incompatible and volatile behavior implies that their distribution is influenced by partial melting, fractionation and degassing processes as well as fluid mobilities. The heavy halogens, particularly bromine and iodine, are far more depleted in the Earth's mantle than expected from their condensation temperature (Palme and O'Neill 2014), so that their very low abundances in basalts and peridotites (ppb-range) make it analytically challenging to investigate their concentrations in Earth's mantle reservoirs and their behavior during transport processes (Pyle and Mather, 2009). We used a new experimental technique, which combines the irradiation technique (Johnson et al. 2000), laser ablation and conventional mass spectrometry. This enables us to present the first experimentally derived bromine partition coefficient between olivine and melt. Partitioning experiments were performed at 1500° C and 2.3 GPa, a P-T condition that is representative for partial melting processes in the OIB source region (Davis et al. 2011). The bromine partition coefficient between olivine and silicate melt at this condition has been determined to DBrol/melt = 4.37•10-4± 1.96•10-4. Results show that bromine is significantly more incompatible than chlorine (˜1.5 orders of magnitude) and fluorine (˜2 orders of magnitude) due to its larger ionic radius. We have used our bromine partitioning data to estimate minimum bromine abundances in EM1 and EM2 source regions. We used minimum bromine bulk rock concentrations determined in an EM1 (Pitcairn: 1066 ppb) and EM2 (Society: 2063 ppb) basalt (Kendrick et al. 2012), together with an estimated minimum melt fraction of 0.01 in OIB source regions (Dasgupta et al. 2007). The almost perfect bromine incompatibility results in minimum bromine abundances in EM1 and EM2 OIB source regions of 11 ppb and 20 ppb, respectively. The effect on the partitioning behaviour of other minerals such as pyroxene, mantle inhomogeneity, incongruent melting, a potential effect of iron, temperature, pressure or the presence of fluids, would be to shift the estimated bromine mantle source concentration to higher but not to lower values. Comparing our minimum bromine OIB source region estimate with the estimated primitive mantle bromine abundance (3.6 ppb; Lyubetskaya and Korenaga, 2007) implies that the OIB source mantle is enriched in bromine relative to the primitive mantle by at least a factor of 3 in EM1 source regions and a factor of 5.5 in EM2 source regions. One explanation is that bromine may be efficiently recycled into the OIB source mantle region through recycling of subducted oceanic crust. Dasgupta R, Hirschmann MM, Humayun, ND (2007) J. Petrol. 48, pp. 2093-2124. Davis FA, Hirschmann MM, Humayun M (2011) Earth Planet. Sci. Lett. 308, pp. 380-390. Johnson L, Burgess R, Turner G, Milledge JH, Harris JW (2000) Geochim. Cosmochim. Acta 64, pp. 717-732. Kendrick MA, Woodhead JD, Kamenetsky VS (2012) Geol. 32, pp. 441-444. Lyubetskaya T, Korenaga J (2007) J. Geophys. Res.-Sol. Earth 112, B03211. Palme H, O'Neill HStC (2014). Cosmochemical Estimates of Mantle Composition. Treat. Geochem. 2nd edition, 3, pp. 1-39. Pyle DM, Mather TA (2009) Chem. Geol. 263, pp. 110-121.

Argon-40/Argon-39 Age Spectra of Apollo 17 Highlands Breccia Samples by Laser Step Heating and the Age of the Serenitatis Basin

NASA Technical Reports Server (NTRS)

Dalrymple, G. Brent; Ryder, Graham

1996-01-01

We have obtained high-resolution (21-63 steps) Ar-40/Ar-39 age spectra using a continuous laser system on 19 submilligram samples of melt rocks and clasts from Apollo 17 samples collected from the pre-Imbrian highlands in the easternmost part of the Serenitatis basin. The samples include poikilitic melt rocks inferred to have been formed in the Serenitatis basin-forming impact, aphanitic melt rock whose compositions vary and whose provenance is uncertain, and granulite, gabbro, and melt clasts. Three of the poikilitic melts have similar age spectrum plateau ages (72395,96, 3893 +/- 16 Ma (2sigma); 72535,7, 3887 +/- 16 Ma; 76315,150, 3900 +/- 16 Ma) with a weighted mean age of 3893 +/- 9 Ma, which we interpret as the best age for the Serenitatis basin- forming impact. Published Ar-40/Ar-39 age spectrum ages of Apollo 17 poikilitic melts are consistent with our new age but are much less precise. Two poikilitic melts did not give plateaus and the maxima in their age spectra indicate ages of greater than or equal to 3869 Ma (72558,7) and greater than or equal to 3743 Ma (77135,178). Plateau ages of two poikilitic melts and two gabbro clasts from 73155 range from 3854 +/- 16 Ma to 3937 +/- 16 Ma and have probably been affected by the ubiquitous (older?) clasts and by post- formation heating (impact) events. Plateau ages from two of the aphanitic melt 'blobs' and two granulites in sample 72255 fall in the narrow range of 3850 q 16 Ma to 3869 q 16 Ma with a weighted mean of 3862 +/- 8 Ma. Two of the aphanitic melt blobs from 72255 have ages of 3883 +/- 16 Ma and greater than or equal to 3894 Ma, whereas a poikilitic melt clast (of different composition from the 'Serenitatis' melts) has an age of 3835 +/- 16 Ma, which is the upper limit for the accretion of 72255. These data suggest that either the aphanitic melts vary in age, as is also suggested by their varying chemical compositions, or they formed in the 72255 accretionary event about 3.84-3.85 Ga and older relict material is responsible for the dispersion of ages. In any case the aphanitic melts do not appear to be Serenitatis products. Our age for the Serenitatis impact shows, on the basis of the isotopic age evidence alone, that Serenitatis is greater than 20-25 Ma and probably greatr than 55-60 Ma older than Imbrium (less than or equal to 3870 Ma and probably less than or equal to 3836 Ma (Dalrymple and Ryder, 19931). Noritic granulite sample 78527 has a plateau age of 4146 +/- 17 Ma, representing a minimum age for cooling of this sample in the early lunar crust. So far there is no convincing evidence in the lunar melt rock record for basin-forming impacts significantly older than 3.9 Ga.

Making mushy magma chambers in the lower continental crust: Cold storage and compositional bimodality

NASA Astrophysics Data System (ADS)

Jackson, Matthew; Blundy, Jon; Sparks, Steve

2017-04-01

Increasing geological and geophysical evidence suggests that crustal magma reservoirs are normally low melt fraction 'mushes' rather than high melt fraction 'magma chambers'. Yet high melt fractions must form within these mush reservoirs to explain the observed flow and eruption of low crystallinity magmas. In many models, crystallinity is linked directly to temperature, with higher temperature corresponding to lower crystallinity (higher melt fraction). However, increasing temperature yields less evolved (silicic) melt composition for a given starting material. If mobile, low crystallinity magmas require high temperature, it is difficult to explain how they can have evolved composition. Here we use numerical modelling to show that reactive melt flow in a porous and permeable mush reservoir formed by the intrusion of numerous basaltic sills into the lower continental crust produces magma in high melt fraction (> 0.5) layers akin to conventional magma chambers. These magma-chamber-like layers contain evolved (silicic) melt compositions and form at low (close to solidus) temperatures near the top of the mush reservoir. Evolved magma is therefore kept in 'cold storage' at low temperature, but also at low crystallinity so the magma is mobile and can leave the mush reservoir. Buoyancy-driven reactive flow and accumulation of melt in the mush reservoir controls the temperature and composition of magma that can leave the reservoir. The modelling also shows that processes in lower crustal mush reservoirs produce mobile magmas that contain melt of either silicic or mafic composition. Intermediate melt compositions are present but are not within mobile magmas. Silicic melt compositions are found at high melt fraction within the magma-chamber like layers near the top of the mush reservoir. Mafic melt compositions are found at high melt fraction within the cooling sills. Melt elsewhere in the reservoir has intermediate composition, but remains trapped in the reservoir because the local melt fraction is too low to form a mobile magma. The model results are consistent with geochemical data suggesting that lower crustal magma reservoirs supply silicic and mafic melts to arc volcanoes, but intermediate magmas are formed by mixing in shallower reservoirs. We suggest here that lower crustal magma chambers primarily form in response to changes in bulk composition caused by melt migration and chemical reaction in a mush reservoir. This process is different to the conventional and widely applied models of magma chamber formation. Similar processes are likely to operate in shallow mush reservoirs, but will likely be further complicated by the presence of volatile phases, and mixing of different melt compositions sourced from deeper mush reservoirs.

Major and trace element modeling of mid-ocean ridge mantle melting from the garnet to the plagioclase stability fields: Generating local and global compositional variability

NASA Astrophysics Data System (ADS)

Brown, S. M.; Behn, M. D.; Grove, T. L.

2017-12-01

We present results of a combined petrologic - geochemical (major and trace element) - geodynamical forward model for mantle melting and subsequent melt modification. The model advances Behn & Grove (2015), and is calibrated using experimental petrology. Our model allows for melting in the plagioclase, spinel, and garnet fields with a flexible retained melt fraction (from pure batch to pure fractional), tracks residual mantle composition, and includes melting with water, variable melt productivity, and mantle mode calculations. This approach is valuable for understanding oceanic crustal accretion, which involves mantle melting and melt modification by migration and aggregation. These igneous processes result in mid-ocean ridge basalts that vary in composition at the local (segment) and global scale. The important variables are geophysical and geochemical and include mantle composition, potential temperature, mantle flow, and spreading rate. Accordingly, our model allows us to systematically quantify the importance of each of these external variables. In addition to discriminating melt generation effects, we are able to discriminate the effects of different melt modification processes (inefficient pooling, melt-rock reaction, and fractional crystallization) in generating both local, segment-scale and global-scale compositional variability. We quantify the influence of a specific igneous process on the generation of oceanic crust as a function of variations in the external variables. We also find that it is unlikely that garnet lherzolite melting produces a signature in either major or trace element compositions formed from aggregated melts, because when melting does occur in the garnet field at high mantle temperature, it contributes a relatively small, uniform fraction (< 10%) of the pooled melt compositions at all spreading rates. Additionally, while increasing water content and/or temperature promote garnet melting, they also increase melt extent, pushing the pooled composition to lower Sm/Yb and higher Lu/Hf.

Upgrading of automobile shredder residue via innovative granulation process 'ReGran'.

PubMed

Holthaus, Philip; Kappes, Moritz; Krumm, Wolfgang

2017-01-01

Stricter regulatory requirements concerning end-of-life vehicles and rising disposal costs necessitate new ways for automobile shredder residue utilisation. The shredder granulate and fibres, produced by the VW-SICON-Process, have a high energy content of more than 20 MJ kg -1 , which makes energy recovery an interesting possibility. Shredder fibres have a low bulk density of 60 kg m -3 , which prevents efficient storing and utilisation as a refuse-derived fuel. By mixing fibres with plastic-rich shredder granulate and heating the mixture, defined granules can be produced. With this 'ReGran' process, the bulk density can be enhanced by a factor of seven by embedding shredder fibres in the partially melted plastic mass. A minimum of 26-33 wt% granulate is necessary to create enough melted plastic. The process temperature should be between 240 °C and 250 °C to assure fast melting while preventing extensive outgassing. A rotational frequency of the mixing tool of 1000 r min -1 during heating and mixing ensures a homogenous composition of the granules. During cooling, lower rotational frequencies generate bigger granules with particles sizes of up to 60 mm at 300 r min -1 . To keep outgassing to a minimum, it is suggested to melt shredder granulate first and then add shredder fibres. Adding coal, wood or tyre fluff as a third component reduces chlorine levels to less than 1 wt%. The best results can be achieved with tyre fluff. In combination with the VW-SICON-Process, ReGran produces a solid recovered fuel or 'design fuel' tailored to the requirements of specific thermal processes.

The Minimum Potential Temperature of the Hawaiian Mantle is About 1420°C

NASA Astrophysics Data System (ADS)

Gudfinnsson, G. H.; Presnall, D. C.

2002-12-01

Picritic glasses found in turbidite sands near the submarine part of Kilauea's East Rift Zone contain up to 15 wt.% MgO and are the most magnesian Hawaiian volcanic glasses reported to date (Clague et al., 1991, 1995). They have olivine phenocrysts as magnesian as Fo90.7, and when their compositions are plotted together on normative diagrams, they form a distinct olivine fractionation trend. Melt geothermometers indicate that the eruption temperatures of the picrite magmas were as high as about 1320°C. On the assumption that these glasses represent primary melt compositions that coexisted with a lherzolite phase assemblage, the CMASNF geothermometer (Gudfinnsson and Presnall, 2001) yields a maximum temperature of generation of about 1480°C, which corresponds roughly to a pressure of 2.5 GPa. This assumes that the melts were essentially free of H2O and CO2. However, both of these volatile components have the potential to lower significantly the solidus temperatures of mantle peridotite and alter the chemistry of primary melts. The approximately 0.4 wt.% H2O measured in the Hawaiian picrite glasses is probably below the saturation limit for H2O, and can be assumed to be close to the original H2O content of the picrite melts. The measured amount of CO2 in the glasses is low as most CO2 was probably lost by degassing at the time of eruption. The CO2 content of primary magmas at Kilauea has been determined as 0.7 wt.% (Gerlach and Graeber, 1985; Gerlach et al., 2001). Whereas the addition of CO2 tends to shift melts derived from peridotite toward greater alkalinity, the addition of H2O tends to move liquids toward the quartz normative side of the basalt tetrahedron. Results of CO2- and H2O-bearing melting experiments indicate that with the low amounts of H2O and CO2 expected in the primary melts of Kilauea their effect on the position of phase boundaries will be small. From phase relations involving melt in equilibrium with a garnet lherzolite phase assemblage in the system CaO-MgO-Al2O3-SiO2-CO2, we estimate that the solidus temperature of mantle lherzolite is lowered by about 10°C for each 1 wt.% increase in the amount of CO2 in the melt. The effect of H2O is to lower the solidus temperature about 40°C for each 1 wt.% increase in this component. This yields a minimum potential temperature (Tp) for Hawaii of about 1420°C, which is consistent with data indicating at most only a very slight increase of heat flow at Hawaii relative to Pacific crust of the same age (Stein and Stein, 1993). This Tp is 140-160°C higher than petrological estimates of the average Tp of the MORB source (McKenzie and Bickle, 1988; Presnall et al., 2002). Our data do not constrain the upper limit of Tp at Hawaii.

New Experimental Results on the Interaction of Molten Corium with Reactor Vessel Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bechta, S.V.; Khabensky, V.B.; Granovsky, V.S.

In order to justify the concept of in-vessel core melt retention, it is necessary to understand the thermal and physico-chemical phenomena. Especially the interaction of the molten pool with the reactor vessel during outside cooling needs to be understood. These phenomena are very complex, in particular, where interactions with the oxidic melt are concerned. In the early stages of the retention process, the oxidic corium and the vessel steel interact under the conditions of low oxygen potential in the melt. These conditions can be simulated by a molten corium having the composition UO{sub 2}/ZrO{sub 2}/Zr, where the degree of Zr-oxidationmore » is in the range between 30 % (C-30) and 100 % (C-100). Corresponding experiments with prototypic melts at low oxygen potentials are being performed in the ISTC METCOR project 2. phase. These are: - MC 5 of corium composition 71w%UO{sub 2}-29w%ZrO{sub 2} (C-100) in neutral atmosphere (argon), - MC 6 of corium composition 76w%UO{sub 2}-9w%ZrO{sub 2}-15w%Zr (C{approx}30), also in argon. In test MC 5, the interaction of molten C-100 corium with a water-cooled steel specimen was studied for the following maximum temperatures at the specimen surface: 1075 deg. C, 1180 deg. C, 1315 deg. C and 1435 deg. C. The total duration of the experiment was {approx} 36 hours. The MC 5 test serves as a reference test for determining the characteristics of the interaction between oxidic melt and steel specimen under the conditions of minimum chemical interaction potential. To investigate the effect of substoichiometry, test No 6 was then performed with sub-oxidized molten corium C{approx}30. The maximum surface temperature of the cooled steel specimen was held at {approx} 1400 deg. C. The test duration was {approx} 10 hours. The ablation phenomena were found to differ significantly from those observed both in the reference test, as well as in former tests with oxidized melts, as they involved the formation of a low-melting metallic phase at the interface which contains iron, zirconium and uranium. The paper summarizes the results of the experiments and of the performed posttest analysis for tests MC 5 and MC 6. (authors)« less

Oxygen isotope composition of mafic magmas at Vesuvius

NASA Astrophysics Data System (ADS)

Dallai, L.; Cioni, R.; Boschi, C.; D'Oriano, C.

2009-12-01

The oxygen isotope composition of olivine and clinopyroxene from four plinian (AD 79 Pompeii, 3960 BP Avellino), subplinian (AD 472 Pollena) and violent strombolian (Middle Age activity) eruptions were measured to constrain the nature and evolution of the primary magmas of the last 4000 years of Mt. Vesuvius activity. A large set of mm-sized crystals was accurately separated from selected juvenile material of the four eruptions. Crystals were analyzed for their major and trace element compositions (EPMA, Laser Ablation ICP-MS), and for 18O/16O ratios. As oxygen isotope composition of uncontaminated mantle rocks on world-wide scale is well constrained (δ18Oolivine = 5.2 ± 0.3; δ18Ocpx = 5.6 ± 0.3 ‰), the measured values can be conveniently used to monitor the effects of assimilation/contamination of crustal rocks in the evolution of the primary magmas. Instead, typically uncontaminated mantle values are hardly recovered in Italian Quaternary magmas, mostly due to the widespread occurrence of crustal contamination of the primary magmas during their ascent to the surface (e.g. Alban Hills, Ernici Mts., and Aeolian Islands). Low δ18O values have been measured in olivine from Pompeii eruption (δ18Oolivine = 5.54 ± 0.03‰), whereas higher O-compositions are recorded in mafic minerals from pumices or scoria of the other three eruptions. Measured olivine and clinopyroxene share quite homogeneous chemical compositions (Olivine Fo 85-90 ; Diopside En 45-48, respectively), and represent phases crystallized in near primary mafic magmas, as also constrained by their trace element compositions. Data on melt inclusions hosted in crystals of these compositions have been largely collected in the past demonstrating that they crystallized from mafic melt, basaltic to tephritic in composition. Published data on volatile content of these melt inclusions reveal the coexistence of dissolved water and carbon dioxide, and a minimum trapping pressure around 200-300 MPa, suggesting that crystal growth possibly occurred during magma ascent from the source region or in a shallow reservoir at about 8-10 km depth. Recently, experimental data have suggested massive carbonate assimilation (up to about 20%) to derive potassic alkali magmas from trachybasaltic melts. Accordingly, the δ18O variability and the trace element contents of the studied minerals suggest possible contamination of primary melts by an O-isotope enriched, REE-poor contaminant like the limestone of Vesuvius basement. The δ18Oolivine and δ18Ocpx of the studied minerals define variable degrees of carbonate assimilation and magma crystallization for the different eruptions, and possibly within the same eruption, and show evidence of oxygen isotope equilibrium at high temperature. However, energy-constrained AFC model suggest that carbonate contamination was limited. On the basis of our data, we suggest that interaction between magma and a fluxing, decarbonation-derived CO2 fluid may be partly accounted for the measured O-isotope compositions.

Strengthening materials specifications

NASA Astrophysics Data System (ADS)

Sampath, K.

2005-10-01

Continuing efforts to strengthen materials specifications readily recognize that a mere compliance with a materials specification only assures a material meeting or exceeding the minimum expectations explicitly detailed in the specification. Implicitly, such efforts also recognize that additional and specific client needs must be addressed as supplementary requirements and introduced during material procurement to reduce risks and assure enhanced performance. This article describes two U.S. Navy-related case studies that allowed further strengthening of the materials specification process, using newer methods and renewed understanding. The first case demonstrates the use of a constraints-based modeling approach to specify the chemical composition of high-performance welding electrodes for critical U.S. Navy applications. This approach helps to distinguish high-performance welding electrode chemical compositions from rich and lean welding electrode chemical compositions that might limit the operational envelope, reduce performance, or both, while increasing overall cost of fabrication but otherwise meet electrode specification requirements. The second case identifies that the size of an ingot could be an important factor while specifying the aluminum and sulfur contents of very large-size, heavy-gauge plates. Renewed understanding of melt fluidity issues associated with the solidification of very large-size ingots shows that deficiencies in through-thickness ductility of heavy-gauge plates are related to controlling aluminum and sulfur contents of the voluminous melt, notwithstanding explicit compliance with specification requirements.

Influence of Silicate Melt Composition on Metal/Silicate Partitioning of W, Ge, Ga and Ni

NASA Technical Reports Server (NTRS)

Singletary, S. J.; Domanik, K.; Drake, M. J.

2005-01-01

The depletion of the siderophile elements in the Earth's upper mantle relative to the chondritic meteorites is a geochemical imprint of core segregation. Therefore, metal/silicate partition coefficients (Dm/s) for siderophile elements are essential to investigations of core formation when used in conjunction with the pattern of elemental abundances in the Earth's mantle. The partitioning of siderophile elements is controlled by temperature, pressure, oxygen fugacity, and by the compositions of the metal and silicate phases. Several recent studies have shown the importance of silicate melt composition on the partitioning of siderophile elements between silicate and metallic liquids. It has been demonstrated that many elements display increased solubility in less polymerized (mafic) melts. However, the importance of silicate melt composition was believed to be minor compared to the influence of oxygen fugacity until studies showed that melt composition is an important factor at high pressures and temperatures. It was found that melt composition is also important for partitioning of high valency siderophile elements. Atmospheric experiments were conducted, varying only silicate melt composition, to assess the importance of silicate melt composition for the partitioning of W, Co and Ga and found that the valence of the dissolving species plays an important role in determining the effect of composition on solubility. In this study, we extend the data set to higher pressures and investigate the role of silicate melt composition on the partitioning of the siderophile elements W, Ge, Ga and Ni between metallic and silicate liquid.

Probing the atomic structure of basaltic melts generated by partial melting of upper mantle peridotite (KLB-1): Insights from high-resolution solid-state NMR study

NASA Astrophysics Data System (ADS)

Park, S. Y.; Lee, S. K.

2015-12-01

Probing the structural disorder in multi-component silicate glasses and melts with varying composition is essential to reveal the change of macroscopic properties in natural silicate melts. While a number of NMR studies for the structure of multi-component silicate glasses and melts including basaltic and andesitic glasses have been reported (e.g., Park and Lee, Geochim. Cosmochim. Acta, 2012, 80, 125; Park and Lee, Geochim. Cosmochim. Acta, 2014, 26, 42), many challenges still remain. The composition of multi-component basaltic melts vary with temperature, pressure, and melt fraction (Kushiro, Annu. Rev. Earth Planet. Sci., 2001, 71, 107). Especially, the eutectic point (the composition of first melt) of nepheline-forsterite-quartz (the simplest model of basaltic melts) moves with pressure from silica-saturated to highly undersaturated and alkaline melts. The composition of basaltic melts generated by partial melting of upper mantle peridotite (KLB-1, the xenolith from Kilbourne Hole) also vary with pressure. In this study we report experimental results for the effects of composition on the atomic structure of Na2O-MgO-Al2O3-SiO2 (NMAS) glasses in nepheline (NaAlSiO4)-forsterite (Mg2SiO4)-quartz (SiO2) eutectic composition and basaltic glasses generated by partial melting of upper mantle peridotite (KLB-1) using high-resolution multi-nuclear solid-state NMR. The Al-27 3QMAS (triple quantum magic angle spinning) NMR spectra of NMAS glasses in nepheline-forsterite-quartz eutectic composition show only [4]Al. The Al-27 3QMAS NMR spectra of KLB-1 basaltic glasses show mostly [4]Al and a non-negligible fraction of [5]Al. The fraction of [5]Al, the degree of configurational disorder, increases from 0 at XMgO [MgO/(MgO+Al2O3)]=0.55 to ~3% at XMgO=0.79 in KLB-1 basaltic glasses while only [4]Al are observed in nepheline-forsterite-quartz eutectic composition. The current experimental results provide that the fraction of [5]Al abruptly increases by the effect of composition as well as pressure in natural silicate melts. The changes of the fraction of highly coordinated Al in multi-component silicate glasses and melts with composition can provide insight into the changes of macroscopic properties (e.g., entropy, viscosity, and diffusivity) with varying composition of melt.

Martian regolith in Elephant Moraine 79001 shock melts? Evidence from major element composition and sulfur speciation

NASA Astrophysics Data System (ADS)

Walton, E. L.; Jugo, P. J.; Herd, C. D. K.; Wilke, M.

2010-08-01

Shock veins and melt pockets in Lithology A of Martian meteorite Elephant Moraine (EETA) 79001 have been investigated using electron microprobe (EM) analysis, petrography and X-ray Absorption Near Edge Structure (XANES) spectroscopy to determine elemental abundances and sulfur speciation (S 2- versus S 6+). The results constrain the materials that melted to form the shock glasses and identify the source of their high sulfur abundances. The XANES spectra for EETA79001 glasses show a sharp peak at 2.471 keV characteristic of crystalline sulfides and a broad peak centered at 2.477 keV similar to that obtained for sulfide-saturated glass standards analyzed in this study. Sulfate peaks at 2.482 keV were not observed. Bulk compositions of EETA79001 shock melts were estimated by averaging defocused EM analyses. Vein and melt pocket glasses are enriched in Al, Ca, Na and S, and depleted in Fe, Mg and Cr compared to the whole rock. Petrographic observations show preferential melting and mobilization of plagioclase and pyrrhotite associated with melt pocket and vein margins, contributing to the enrichments. Estimates of shock melt bulk compositions obtained from glass analyses are biased towards Fe- and Mg- depletions because, in general, basaltic melts produced from groundmass minerals (plagioclase and clinopyroxene) will quench to a glass, whereas ultramafic melts produced from olivine and low-Ca pyroxene megacrysts crystallize during the quench. We also note that the bulk composition of the shock melt pocket cannot be determined from the average composition of the glass but must also include the crystals that grew from the melt - pyroxene (En 72-75Fs 20-21Wo 5-7) and olivine (Fo 75-80). Reconstruction of glass + crystal analyses gives a bulk composition for the melt pocket that approaches that of lithology A of the meteorite, reflecting bulk melting of everything except xenolith chromite. Our results show that EETA79001 shock veins and melt pockets represent local mineral melts formed by shock impedance contrasts, which can account for the observed compositional anomalies compared to the whole rock sample. The observation that melts produced during shock commonly deviate from the bulk composition of the host rock has been well documented from chondrites, rocks from terrestrial impact structures and other Martian meteorites. The bulk composition of shock melts reflects the proportions of minerals melted; large melt pockets encompass more minerals and approach the whole rock whereas small melt pockets and thin veins reflect local mineralogy. In the latter, the modal abundance of sulfide globules may reach up to 15 vol%. We conclude the shock melt pockets in EETA79001 lithology A contain no significant proportion of Martian regolith.

Melting phenomena: effect of composition for 55-atom Ag-Pd bimetallic clusters.

PubMed

Cheng, Daojian; Wang, Wenchuan; Huang, Shiping

2008-05-14

Understanding the composition effect on the melting processes of bimetallic clusters is important for their applications. Here, we report the relationship between the melting point and the metal composition for the 55-atom icosahedral Ag-Pd bimetallic clusters by canonical Monte Carlo simulations, using the second-moment approximation of the tight-binding potentials (TB-SMA) for the metal-metal interactions. Abnormal melting phenomena for the systems of interest are found. Our simulation results reveal that the dependence of the melting point on the composition is not a monotonic change, but experiences three different stages. The melting temperatures of the Ag-Pd bimetallic clusters increase monotonically with the concentration of the Ag atoms first. Then, they reach a plateau presenting almost a constant value. Finally, they decrease sharply at a specific composition. The main reason for this change can be explained in terms of the relative stability of the Ag-Pd bimetallic clusters at different compositions. The results suggest that the more stable the cluster, the higher the melting point for the 55-atom icosahedral Ag-Pd bimetallic clusters at different compositions.

Melting Processes at the Base of the Mantle Wedge: Melt Compositions and Melting Reactions for the First Melts of Vapor-Saturated Lherzolite

NASA Astrophysics Data System (ADS)

Grove, T. L.; Till, C. B.

2014-12-01

Vapor-saturated melting experiments have been performed at pressures near the base of the mantle wedge (3.2 GPa). The starting composition is a metasomatized lherzolite containing 3 wt. % H2O. Near-solidus melts and coexisting mineral phases have been characterized in experiments that span 925 to 1100 oC with melt % varying from 6 to 9 wt. %. Olivine, orthopyroxene, clinopyroxene and garnet coexist with melt over the entire interval and rutile is also present at < 1000 oC. Melt is andesitic in composition and varies from 60 wt. % SiO2 at 950 oC to 52 wt. % at 1075 oC. The Al2O3 contents of the melt are 13 to 14 wt. %, and CaO contents range from 1 and 4 wt. %. Melting is peritectic with orthopyroxene + liquid produced by melting of garnet + olivine + high-Ca pyroxene. In addition to quenched melt, we observe a quenched silicate component that is rhyolitic (>72 % SiO2) that we interpret as a precipitate from the coexisting supercritical H2O-rich vapor. Extrapolation of the measured compositional variation toward the solidus suggests that the first melt may be very SiO2 rich (i.e., granitic). We suggest that these granitic melts are the first melts of the mantle near the slab-wedge interface. As these SiO2-rich melts ascend into shallower, hotter overlying mantle, they continue to interact with the surrounding mantle and evolve in composition. These first melts may elucidate the geochemical and physical processes that accompany the beginnings of H2O flux melting.

Influence Of The Redox State On The Electrical Conductivity Of Basaltic Melts

NASA Astrophysics Data System (ADS)

Pommier, A.; Gaillard, F.; Pichavant, M.

2007-12-01

The electrical conductivity is an efficient probe of mass transfer processes within silicate melts and magmas. Previous studies have established that the electrical conductivity is sensitive to parameters such as temperature, melt composition and pressure. In contrast to what is known for Fe-bearing minerals, little attention has been given to the influence of redox state on the electrical conductivity of melts. Experiments were performed on tephritic and basaltic compositions respectively from Mt. Vesuvius and Pu'u 'O'o. Measurements were carried out on cylindrical glass samples (OD: 6 mm, ID: 1 mm, L: 8 mm) drilled from glass obtained by fusing each rock sample at 1400°C in air. A two-electrode configuration was adopted, with the electrical impedance being radially measured. A Pt wire was used as the internal electrode whereas a Pt tube served as the external electrode. Experiments were conducted at 1 atm in a vertical furnace between 1200°C and 1300°C, both in air and in a CO-CO2 atmosphere at a fO2 corresponding to NNO+1. Both reduction and oxidation experiments were performed. In reduction experiments (pure CO2 then CO-CO2 gas mixture), electrical conductivities progressively increase with time. The reverse is observed in oxidation experiments (CO-CO2 gas mixture then pure CO2). These variations of electrical conductivities are correlated with modifications of the Fe2+/Fe3+ ratio in the melt, and are consistent with the respective structural roles of Fe2+ and Fe3+. In both types of experiments, a minimum of about 400 mn is necessary before a plateau is reached, interpreted to reflect the kinetics of attainment of the equilibrium Fe2+/Fe3+ ratio in the melt. Differences between plateau and initial values are typically of a few ohms, much higher than the sensitivity of our measurements (better than 0.1 ohm). When increasing temperature, the time required for reaching plateau values decreases. At NNO+1, the electrical activation energy (Ea) was determined for both compositions: Ea=137 kJ/mol (tephrite) and 73 kJ/mol (basalt). Further experiments are necessary to quantify the influence of redox state on electrical conductivity, especially at fO2 below NNO+1.

Numerically design the injection process parameters of parts fabricated with ramie fiber reinforced green composites

NASA Astrophysics Data System (ADS)

Chen, L. P.; He, L. P.; Chen, D. C.; Lu, G.; Li, W. J.; Yuan, J. M.

2017-01-01

The warpage deformation plays an important role on the performance of automobile interior components fabricated with natural fiber reinforced composites. The present work investigated the influence of process parameters on the warpage behavior of A pillar trim made of ramie fiber (RF) reinforced polypropylene (PP) composites (RF/PP) via numerical simulation with orthogonal experiment method and range analysis. The results indicated that fiber addition and packing pressure were the most important factors affecting warpage. The A pillar trim can achieved the minimum warpage value as of 2.124 mm under the optimum parameters. The optimal process parameters are: 70% percent of the default value of injection pressure for the packing pressure, 20 wt% for the fiber addition, 185 °C for the melt °C for the mold temperature, 7 s for the filling time and 17 s for the packing time.

Mantle xenoliths from Central Vietnam: evidence for at least Meso-Proterozoic formation of the lithospheric mantle

NASA Astrophysics Data System (ADS)

Proßegger, Peter; Ntaflos, Theodoros; Ackerman, Lukáš; Hauzenberger, Christoph; Tran, Tuan Anh

2016-04-01

Intraplate Cenozoic basalts that are widely dispersed along the continental margin of East Asia belong to the Western Pacific "diffuse" igneous province. They consist mainly of alkali basalts, basanites,rarely nephelinites, which are mantle xenolith-bearing, potassic rocks and quartz tholeiites. The volcanism in this area has been attributed to the continental extension caused by the collision of India with Asia and by the subduction of the Pacific Ocean below Asia. We studied a suite of 24 mantle xenoliths from La Bang Lake, Dak Doa district and Bien Ho, Pleiku city in the Gia Province, Central Vietnam. They are predominantly spinel lherzolites (19) but spinel harburgites (3) and two garnet pyroxenites are present as well. The sizes of the xenoliths range from 5 to 40 cm in diameter with medium to coarse-grained protogranular textures. Whole rock major and trace element analyses display a wide range of compositions. The MgO concentration varies from 36.0 to 45.8 wt% whereas Al2O3 and CaO range from 0.63 to 4.36 wt% and from 0.52 to 4.21 wt% (with one sample having CaO of 6.63 wt%) respectively. Both CaO and Al2O3 positively correlate with MgO most likely indicating that the sampled rocks were derived from a common mantle source experienced variable degrees of partial melting. Mineral analyses show that the rock forming minerals are chemically homogeneous. The Fo contents of olivine vary between 89.2 and 91.2 and the Mg# of orthopyroxene and clinopyroxene range from 89 to 92 and 89 to 94 respectively. The range of Cr# for spinel is 0.06-0.26. Model calculations in both whole rock and clinopyroxenes show that lithospheric mantle underneath Central Vietnam experienced melt extractions that vary between 2-7, 12-15 and 20-30%. The majority of the primitive mantle-normalized whole rock and clinopyroxene REE patterns are parallel to each other indicating that clinopyroxene is the main repository of the trace elements. Clinopyroxenes are divided into two groups: group A with concave upwards REE and (La/Yb)N < 1 suggesting various degrees of melt extraction and group B with (La/Yb)N ranging between 1 and 10. The group B in a mantle normalized trace element diagram shows negative Pb and Sr anomalies compared to their neighbour elements, which together with the general absence of hydrous phases, suggest variable interaction with percolating silicate melt(s). The primitive-mantle normalized highly siderophile element (HSE) concentration pattern show almost no fractionation among Ir, Ru and Pt with only slight depletion in Os suggesting very limited effect of metasomatism on the HSE contents. On the other hand, most of the samples display clear Re addition from the percolating melts preventing calculation of reliable rhenium depletion ages (TRD). However, one sample with depleted Pd and Re signature yield TRD of 1.0 Ga which can be interpreted as a minimum SCLM stabilization age in this area. Mantle xenoliths from Central Vietnam range from fertile to depleted compositions partly affected by metasomatic silicate melts. Re-Os isotopic composition reveals a Meso-Proterozoic minimum stabilization age of the lithospheric mantle.

Effect of water on the composition of partial melts of greenstone and amphibolite

NASA Technical Reports Server (NTRS)

Beard, James S.; Lofgren, Gary E.

1989-01-01

Closed-system partial melts of hydrated, metamorphosed arc basalts and andesites (greenstones and amphibolites), where only water structurally bound in metamorphic minerals is available for melting (dehydration melting), are generally water-undersaturated, coexist with plagioclase-rich, anhydrous restites, and have compositions like island arc tonalites. In contrast, water-saturated melting at water pressures of 3 kilobars yields strongly peraluminous, low iron melts that coexist with an amphibole-bearing, plagioclase-poor restite. These melt compositions are unlike those of most natural silicic rocks. Thus, dehydration melting over a range of pressures in the crust of island arcs is a plausible mechanism for the petrogenesis of islands arc tonalite, whereas water-saturated melting at pressure of 3 kilobars and above is not.

Partial melting of TTG gneisses: crustal contamination and the production of granitic melts

NASA Astrophysics Data System (ADS)

Meade, F. C.; Masotta, M.; Troll, V. R.; Freda, C.; Johnson, T. E.; Dahren, B.

2011-12-01

Understanding partial melting of ancient TTG gneiss terranes is crucial when considering crustal contamination in volcanic systems, as these rocks are unlikely to melt completely at magmatic temperatures (1000-1200 °C) and crustal pressures (<500 MPa). Variations in the bulk composition of the gneiss, magma temperature, pressure (depth) and the composition and abundance of any fluids present will produce a variety of melt compositions, from partial melts enriched in incompatible elements to more complete melts, nearing the bulk chemistry of the parent gneiss. We have used piston cylinder experiments to simulate partial melting in a suite of 12 gneisses from NW Scotland (Lewisian) and Eastern Greenland (Ammassalik, Liverpool Land) under magma chamber temperature and pressure conditions (P=200 MPa, T=975 °C). These gneisses form the basement to much of the North Atlantic Igneous Province, where crustal contamination of magmas was commonplace but the composition of the crustal partial melts are poorly constrained [1]. The experiments produced partial melts in all samples (e.g. Fig 1). Electron microprobe analyses of glasses indicate they are compositionally heterogeneous and are significantly different from the whole rock chemistry of the parent gneisses. The melts have variably evolved compositions but are typically trachy-dacitic to rhyolitic (granitic). This integrated petrological, experimental and in-situ geochemical approach allows quantification of the processes of partial melting of TTG gneiss in a volcanic context, providing accurate major/trace element and isotopic (Sr, Pb) end-members for modeling crustal contamination. The experimental melts and restites will be compared geochemically with a suite of natural TTG gneisses, providing constraints on the extent to which the gneisses have produced and subsequently lost melt. [1] Geldmacher et al. (2002) Scottish Journal of Geology, v.38, p.55-61.

Along-strike variability of primitive magmas (major and volatile elements) inferred from olivine-hosted melt inclusions, southernmost Andean Southern Volcanic Zone, Chile

NASA Astrophysics Data System (ADS)

Weller, D. J.; Stern, C. R.

2018-01-01

Glass compositions of melt inclusions in olivine phenocrysts found in tephras derived from explosive eruptions of the four volcanoes along the volcanic front of the southernmost Andean Southern Volcanic Zone (SSVZ) are used to constrain primitive magma compositions and melt generation parameters. Primitive magmas from Hudson, Macá, and Melimoyu have similar compositions and are formed by low degrees (8-18%) of partial melting. Compared to these other three centers, primitive magmas from Mentolat have higher Al2O3 and lower MgO, TiO2 and other incompatible minor elements, and are generated by somewhat higher degrees (12-20%) of partial melting. The differences in the estimated primitive parental magma compositions between Mentolat and the other three volcanic centers are consistent with difference in the more evolved magmas erupted from these centers, Mentolat magmas having higher Al2O3 and lower MgO, TiO2 and other incompatible minor element contents, suggesting that these differences are controlled by melting processes in the mantle source region above the subducted oceanic plate. Parental magma S = 1430-594 and Cl = 777-125 (μg/g) contents of Hudson, Macá, and Melimoyu are similar to other volcanoes further north in the SVZ. However, Mentolat primitive magmas have notably higher concentrations of S = 2656-1227 and Cl = 1078-704 (μg/g). The observed along-arc changes in parental magma chemistry may be due to the close proximity below Mentolat of the subducted Guamblin Fracture Zone that could efficiently transport hydrous mineral phases, seawater, and sediment into the mantle, driving enhanced volatile fluxed melting beneath this center compared to the others. Table S2. Olivine-hosted melt inclusion compositions, host-olivine compositions, and the post-entrapment crystallization corrected melt inclusion compositions. Table S3. Olivine-hosted melt inclusion modeling information. Table S4. Major element compositions of the fractionation corrected melt inclusion in equilibrium with mantle olivine. Table S5. Melting parameters Fm and CoH2O. Table S6. Major element compositions of phenocrysts and glasses occurring with the olivine-hosted melt inclusions.

How do the radiative effects of springtime clouds and water vapor modulate the melt onset of Arctic sea ice?

NASA Astrophysics Data System (ADS)

Huang, Y.; Dong, X.; Xi, B.; Deng, Y.

2017-12-01

Earlier studies show that there is a strong positive correlation between the mean onset date of snow melt north of 70°N and the minimum Arctic sea ice extent (SIE) in September. Based on satellite records from 1980 to 2016, the September Arctic SIE minimum is most sensitive to the early melt onset over the Siberian Sea (73°-84°N, 90°-155°), which is defined as the area of focus (AOF) in this analysis. The day with melt onset exceeding 10% area of the AOF is marked as the initial melt date for a given year. With this definition, a strong positive correlation (r=0.59 at 99% confidence level) is found between the initial melt date over the AOF and the September SIE minimum over the Arctic. Daily anomalies of cloud and radiation properties are compared between six years with earliest initial melt dates (1990, 2012, 2007, 2003, 1991, 2016) and six years with latest initial melt dates (1996, 1984, 1983, 1982, 1987, 1992) using the NASA MERRA-2 reanalysis. Our results suggest that higher cloud water path (CWP) and precipitable water vapor (PWV) are clearly associated with early melt onset years through the period of mid-March to August. Major contrasts in CWP are found between the early and late onset years in a period of approximately 30 days prior to the onset to 30 days after the onset. As a result, the early melt onset years exhibit positive anomalies for downward longwave flux at the surface and negative anomalies for downward shortwave flux, shortwave cloud radiative effect (CRE) as well as net CRE. The negative net CRE is over-compensated by the positive longwave flux anomaly associated with elevated PWV, contributing to early melt onsets. The temporal evolution of CRE and PWV radiative effect during the entire melting season will be documented together with an analysis tracing the dynamical, mid-latitude origins of increased CWP and PWV prior to initial melt onsets.

Mechanical properties of melt-processed polymer blend of amorphous corn flour composite filler and styrene-butadiene rubber

USDA-ARS?s Scientific Manuscript database

The corn flour composite fillers were prepared by blending corn flour with rubber latex, dried, and cryogenically ground into powders, which were then melt-blended with rubber polymers in an internal mixer to form composites with enhanced mechanical properties. The composites prepared with melt-blen...

A New Spinel-Olivine Oxybarometer: Near-Liquidus Partitioning of V between Olivine-Melt, Spinel-Melt, and Spinel-Olivine in Martian Basalt Composition Y980459 as a Function of Oxygen Fugacity

NASA Technical Reports Server (NTRS)

Papike, J. J.; Le, L.; Burger, P. V.; Shearer, C. K.; Bell, A. S.; Jones, J.

2013-01-01

Our research on valence state partitioning began in 2005 with a review of Cr, Fe, Ti, and V partitioning among crystallographic sites in olivine, pyroxene, and spinel [1]. That paper was followed by several on QUE94201 melt composition and specifically on Cr, V, and Eu partitioning between pyroxene and melt [2-5]. This paper represents the continuation of our examination of the partitioning of multivalent V between olivine, spinel, and melt in martian olivine-phyric basalts of Y980459 composition [6, 7]. Here we introduce a new, potentially powerful oxybarometer, V partitioning between spinel and olivine, which can be used when no melt is preserved in the meteorite. The bulk composition of QUE94201 was ideal for our study of martian pyroxene-phyric basalts and specifically the partitioning between pyroxene-melt for Cr, V, and Eu. Likewise, bulk composition Y980459 is ideal for the study of martian olivine-phyric basalts and specifically for olivine-melt, spinel-melt, and spinel-olivine partitioning of V as a function of oxygen fugacity.

Are Avellino (4365 cal BP) and Pompeii twin plinian eruptions? Pre-eruptive constraints and degassing history

NASA Astrophysics Data System (ADS)

Boudon, Georges; Balcone-Boissard, Hélène; Villemant, Benoît.; Ucciani, Guillaume; Cioni, Raffaello

2010-05-01

Somma-Vesuvius activity started 35 ky ago and is characterized by numerous eruptions of variable composition and eruptive style, sometimes interrupted by long periods of unrest. The main explosive eruptions are represented by four plinian eruptions: Pomici di Base eruption (22 cal ky), Mercato (~8900 cal BP), Avellino (4365 cal BP) and Pompeii (79 AD). The 79 AD eruption embodies the most famous eruption since it's responsible of the destruction of Pompeii and Herculanum and it's the first described eruption. The Avellino eruption represents the last plinian event that preceded the Pompeii eruption. The eruptive sequence is similar to the 79 AD plinian eruption, with an opening phase preceding a main plinian fallout activity which ended by a phreatomagmatic phase. The fallout deposit displays a sharp colour contrast from white to grey pumice, corresponding to a magma composition evolution. We focus our study on the main fallout deposit that we sampled in detail in the Traianello quarry, 9 km North-North East of the crater, to investigate the degassing processes during the eruption, using volatile content and textural observations. Density and vesicularity measurements were obtained on a minimum of 100 pumice clasts sampled in 10 stratigraphic levels in the fallout deposit. On the basis of the density distribution, bulk geochemical data, point analytical measurements on glasses (melt inclusions and residual glass) and textural observations were obtained simultaneously on a minimum of 5 pumice clasts per eruptive unit. The glass composition, in particular the Na/K ratio, evolves from Na-rich phonolite for white pumices to a more K-rich phonolite for grey pumices. The pre-eruptive conditions are constrained by systematic Cl measurements in melt inclusions and matrix glass of pumice clasts. The entire magma was saturated relative to sub-critical fluids (a Cl-rich H2O vapour phase and a brine), with a Cl melt content buffered at ~6000 ppm, and a mean pre-eruptive H2O content depending of the magma composition. Most of the pumices of the different eruptive units show that H2O degassing during the eruption followed a typical closed-system evolution as expected for plinian eruption. Contrary to H2O, Cl was not efficiently degassed during the plinian phase of the eruption: the matrix glass composition remains close to the pre-eruptive content. Compared to the 79AD eruption the degassing processes showed by the whole Avellino plinian phase is more homogeneous and similar to the white pumice phase of the Pompeii eruption whereas the open-system degassing mode identified from the grey pumices of the 79AD eruption is not represented during the Avellino eruption.

Melt in the impact breccias from the Eyreville drill cores, Chesapeake Bay impact structure, USA

NASA Astrophysics Data System (ADS)

Bartosova, Katerina; Hecht, Lutz; Koeberl, Christian; Libowitzky, Eugen; Reimold, Wolf Uwe

2011-03-01

The center of the 35.3 Ma Chesapeake Bay impact structure (85 km diameter) was drilled during 2005/2006 in an ICDP-0USGS drilling project. The Eyreville drill cores include polymict impact breccias and associated rocks (1397-01551 m depth). Tens of melt particles from these impactites were studied by optical and electron microscopy, electron microprobe, and microRaman spectroscopy, and classified into six groups: m1—clear or brownish melt, m2—brownish melt altered to phyllosilicates, m3—colorless silica melt, m4—melt with pyroxene and plagioclase crystallites, m5—dark brown melt, and m6—melt with globular texture. These melt types have partly overlapping major element abundances, and large compositional variations due to the presence of schlieren, poorly mixed melt phases, partly digested clasts, and variable crystallization and alteration. The different melt types also vary in their abundance with depth in the drill core. Based on the chemical data, mixing calculations were performed to determine possible precursors of these melt particles. The calculations suggest that most melt types formed mainly from the thick sedimentary section of the target sequence (mainly the Potomac Formation), but an additional crystalline basement (schist/gneiss) precursor is likely for the most abundant melt types m2 and m5. Sedimentary rocks with compositions similar to those of the melt particles are present among the Eyreville core samples. Therefore, sedimentary target rocks were the main precursor of the Eyreville melt particles. However, the composition of the melt particles is not only the result of the precursor composition but also the result of changes during melting and solidification, as well as postimpact alteration, which must also be considered. The variability of the melt particle compositions reflects the variety of target rocks and indicates that there was no uniform melt source. Original heterogeneities, resulting from melting of different target rocks, may be preserved in impactites of some large impact structures that formed in volatile-rich targets, because no large melt body exists, in which homogenization would have taken place.

Revisiting the Potential of Melt Pond Fraction as a Predictor for the Seasonal Arctic Sea Ice Extent Minimum

NASA Technical Reports Server (NTRS)

Liu, Jiping; Song, Mirong; Horton, Radley M.; Hu, Yongyun

2015-01-01

The rapid change in Arctic sea ice in recent decades has led to a rising demand for seasonal sea ice prediction. A recent modeling study that employed a prognostic melt pond model in a stand-alone sea ice model found that September Arctic sea ice extent can be accurately predicted from the melt pond fraction in May. Here we show that satellite observations show no evidence of predictive skill in May. However, we find that a significantly strong relationship (high predictability) first emerges as the melt pond fraction is integrated from early May to late June, with a persistent strong relationship only occurring after late July. Our results highlight that late spring to mid summer melt pond information is required to improve the prediction skill of the seasonal sea ice minimum. Furthermore, satellite observations indicate a much higher percentage of melt pond formation in May than does the aforementioned model simulation, which points to the need to reconcile model simulations and observations, in order to better understand key mechanisms of melt pond formation and evolution and their influence on sea ice state.

The transition from granite to banded aplite-pegmatite sheet complexes: An example from Megiliggar Rocks, Tregonning topaz granite, Cornwall

NASA Astrophysics Data System (ADS)

Breiter, K.; Ďurišová, J.; Hrstka, T.; Korbelová, Z.; Vašinová Galiová, M.; Müller, A.; Simons, B.; Shail, R. K.; Williamson, B. J.; Davies, J. A.

2018-03-01

The genetic relationship between a granite pluton and adjacent complex of rare-metal pegmatite-aplite-banded sheets (Megiliggar Sheet Complex - MSC) has been studied at the border of the Tregonning topaz granite at Megiliggar Rocks, Cornwall, SW England. Similarities in whole-rock chemical and mineralogical compositions, together with a gradual change in textures away from the granite margin, provide strong evidence for a genetic link between the Tregonning Granite and MSC. The sheets are likely to represent apophyses of residual melt which escaped from the largely crystallized roof of the granite pluton. The escaping melt was peraluminous, had a composition near the F, B, Li slightly enriched granite minimum, and, in comparison with other Cornish granites, was enriched in F, Li, Rb, Cs, Sn, W, Nb, Ta, and U, and depleted in Fe, Mg, Ca, Sr, Th, Zr, and REE. With increasing distance from the Tregonning Granite, the silicate melt crystallized as homogeneous leucogranite sheets and banded complex sheets (i.e. combinations of bands with granitic, aplitic and pegmatitic textures), then layered aplite-pegmatites; this sequence becoming progressively more depleted in the fluxing and volatile elements F, Li, Rb, and Cs, but showing no change in Zr/Hf ratios. The fixed Zr/Hf ratio is interpreted as indicating a direct genetic link (parental melt) between all rock types, however the melt progressively lost fluxing and volatile elements with distance from the granite pluton, probably due to wall-rock reaction or fluid exsolution and migration via fractures. Differentiation of the primary melt into Na-Li-F-rich and separate K-B-rich domains was the dominant chemical process responsible for the textural and mineral diversity of the MSC. On a large (cliff-section) scale, the proximal Na-Li-F-rich leucogranite passes through complex sheets into K-B-rich aplite-pegmatites, whilst at a smaller (<1 m) scale, the K-B-rich bands are interspersed (largely overlain) by Na-Li-F-rich segregations. The grain size differences between the aplite and pegmatite could be related to pressure fluctuations and/or undercooling.

Hematite, pyroxene, and phyllosilicates on Mars: Implications from oxidized impact melt rocks from Manicouagan Crater, Quebec, Canada

NASA Technical Reports Server (NTRS)

Morris, Richard V.; Golden, D. C.; Bell, James F., III; Lauer, H. V., Jr.

1995-01-01

Visible and near-IR reflectivity, Mossbauer, and X ray diffraction data were obtained on powders of impact melt rock from the Manicouagan Impact Crater located in Quebec, Canada. The iron mineralogy is dominated by pyroxene for the least oxidized samples and by hematite for the most oxidized samples. Phyllosilicate (smectite) contents up to 15 wt % were found in some heavily oxidized samples. Nanophase hematite and/or paramagnetic ferric iron is observed in all samples. No hydrous ferric oxides (e.g., goethite, lepidocrocite, and ferrihydrite) were detected, which implies the alteration occurred above 250 C. Oxidative alteration is thought to have occurred predominantly during late-stage crystallization and subsolidus cooling of the impact melt by invasion of oxidizing vapors and/or solutions while the impact melt rocks were still hot. The near-IR band minimum correlated with the extent of aleration (Fe(3+)/Fe(sub tot)) and ranged from approx. 1000 nm (high-Ca pyroxene) to approx. 850 nm (bulk, well-crystalline hematite) for least and most oxidized samples, respectively. Intermediate band positions (900-920 nm) are attributed to low-Ca pyroxene and/or a composite band from hematite-pyroxene assemblages. Manicouagan data are consistent with previous assignments of hematite and pyroxene to the 850 and 1000 nm bands observed in Martian reflectivity spectra. Manicouagan data also show that possible assignments for intermediate band positions (900-920 nm) in Martian spectra are pyroxene and/or hematite-pyroxene assemblages. By analogy with impact melt sheets and in agreement with observables for Mars, oxidative alteration of Martian impact melt sheets above 250 C and subsequent erosion could produce rocks and soils with variable proportions of hematite (both bulk and nanophase), pyroxene, and phyllosilicates as iron-bearing mineralogies. If this process is dominant, these phases on Mars were formed rapidly at relatively high temperatures on a sporadic basis throughout the history of the planet. The Manicouagan samples also show that this mineralogical diversity can be accomplished at constant chemical composition, which is also indicated for Mars from analyses of soil at the two Viking landing sites.

Hematite, pyroxene, and phyllosilicates on Mars: Implications from oxidized impact melt rocks from Manicouagan Crater, Quebec, Canada

NASA Technical Reports Server (NTRS)

Morris, Richard V.; Golden, D. C.; Bell, James F., III; Lauer, H. V., Jr.

1995-01-01

Visible and near-IR refectivity, Moessbauer, and X ray diffraction data were obtained on powders of impact melt rock from the Manicouagan Impact Crater located in Quebec, Canada. The iron mineralogy is dominated by pyroxene for the least oxidized samples and by hematite for the most oxidized samples. Phyllosilicate (smectite) contents up to approximately 15 wt % were found in some heavily oxidized samples. Nanophase hematite and/or paramagnetic ferric iron is observed in all samples. No hydrous ferric oxides (e.g., goethite, lepidocrocite, and ferrihydrite) were detected, which implies the alteration occurred above 250 C. Oxidative alteration is thought to have occurred predominantly during late-stage crystallization and subsolidus cooling of the impact melt by invasion of oxidizing vapors and/or solutions while the impact melt rocks were still hot. The near-IR band minimum correlated with the extent of aleration Fe(3+)/Fe(sub tot) and ranged from approximately 1000 nm (high-Ca pyroxene) to approximately 850 nm (bulk, well-crystalline hematite) for least and most oxidized samples, respectively. Intermediate band positions (900-920 nm) are attributed to low-Ca pyroxene and/or a composite band from hematite-pyroxene assemblages. Manicouagan data are consistent with previous assignments of hematite and pyroxene to the approximately 850 and approximately 1000nm bands observed in Martian reflectivity spectra. Manicouagan data also show that possible assignments for intermediate band positions (900-920 nm) in Martian spectra are pyroxene and/or hematite-pyroxene assemblages. By analogy with impact melt sheets and in agreement with observables for Mars, oxidative alteration of Martian impact melt sheets above 250 C and subsequent erosion could produce rocks and soils with variable proportions of hematite (both bulk and nanophase), pyroxene, and phyllosilicates as iron-bearing mineralogies. If this process is dominant, these phases on Mars were formed rapidly at relativly high temperatures on a sporadic basis throughout the history of the planet. The Manicouagan samples also show that this mineralogical diversity can be accomplished at constant chemical composition, which is also indicated for Mars from the analyses of soil at the two Viking landing sites.

Computational alloy design of (Co1-xNix)88Zr7B4Cu1 nanocomposite soft magnets

NASA Astrophysics Data System (ADS)

Dong, B.; Healy, J.; Lan, S.; Daniil, M.; Willard, M. A.

2018-05-01

The dependence of coercivity on composition is an important factor for establishing optimized soft magnetic properties. In this study, we have used the random anisotropy and coherent rotation models to estimate the variation of coercivity with composition in (Co1-xNix)88Zr7B4Cu1 nanocomposite alloys. Our calculations that the magnetoelastic anisotropy contribution to coercivity dominates for Ni rich compositions (x > 0.5). A small range of compositions (0.65 < x < 0.75) is predicted to result in low values of coercivity (<10 A/m). To validate this prediction, (Co1-xNix)88Zr7B4Cu1 nanocomposites in this range were prepared by melt spinning followed by 3600 s isothermal annealing at the primary crystallization peak temperature (˜673 K). Hysteresis loops were measured using vibrating sample magnetometry at room temperature and saturation magnetostriction was measured using a strain gage based magnetostrictometer. Moderately small coercivities (30-40 A/m) and magnetostrictions (3-4 ppm) were measured at for samples with 0.685 < x < 0.725. Our measured coercivity had a minimum value of 32 A/m at x = 0.725, a shift in composition of about 5 at% in the direction of higher Ni content and without the anticipated low value of coercivity. Several reasons for the inaccuracy of this approach are described, including: ignored contributions from amorphous phase (especially in magnetoealstic anisotropy), composition segregation during crystallization leading to unpredictable compositional shifts in prediction, and the general observation that the predictability of minimum coercivity from minimal combined anisotropies has unexplained deviation even in far less complicated materials.

South-Tibetan partially molten batholiths: geophysical characterization and petrological assessment of their origin

NASA Astrophysics Data System (ADS)

Hetényi, G.; Pistone, M.; Nabelek, P. I.; Baumgartner, L. P.

2017-12-01

Zones of partial melt in the middle crust of Lhasa Block, Southern Tibet, have been geophysically observed as seismically reflective "bright spots" in the past 20 years. These batholiths bear important relevance for geodynamics as they serve as the principal observation at depth supporting channel-flow models in the Himalaya-Tibet orogen. Here we assess the spatial abundance of and partial melt volume fraction within these crustal batholiths, and establish lower and upper estimate bounds using a joint geophysical-petrological approach.Geophysical imaging constrains the abundance of partial melt zones to 5.6 km3 per surface-km2 on average (minimum: 3.1 km3/km2, maximum: 7.6 km3/km2 over the mapped area). Physical properties detected by field geophysics and interpreted by laboratory measurements constrain the amount of partial melt to be between 5 and 26 percent.We evaluate the compatibility of these estimates with petrological modeling based on geotherms, crustal bulk rock compositions and water contents consistent with the Lhasa Block. These simulations determine: (a) the physico-chemical conditions of melt generation at the base of the Tibetan crust and its transport and emplacement in the middle crust; (b) the melt percentage produced at the source, transported and emplaced to form the observed "bright spots". Two main mechanisms are considered: (1) melting induced by fluids produced during mineral dehydration reactions in the underthrusting Indian lower crust; (2) dehydration-melting reactions caused by heating within the Tibetan crust. We find that both mechanisms demonstrate first-order match in explaining the formation of the partially molten "bright spots". Thermal modelling shows that the Lhasa Block batholiths have only small amounts of melt and only for geologically short times (<4.5 Myr), if not continuously fed. This, together with their small size compared to the Tibetan Plateau, suggests that these partially molten zones are ephemeral and local features of the geodynamic evolution. Their transience excludes both long-distance and long-lasting channel flow transport in Tibet.

Partial melting kinetics of plagioclase-diopside pairs

NASA Astrophysics Data System (ADS)

Tsuchiyama, Akira

1985-09-01

Partial melting experiments on plagioclase (An60) and diopside have been carried out using pairs of large crystals to investigate textures and kinetics of melting. The experiments were done at one atmosphere pressure as a function of temperature (1,190 1,307° C) and time (1.5 192 h). Melting took place mainly at the plagioclase-diopside contact planes. Reaction zones composed of fine mixtures of calcic plagioclase and melt were developed from the surface of the plagioclase crystal inward. There exists a critical temperature, below which only a few % melting can occur over the duration of the experiments. This sluggish melting is caused by slow NaSi-CaAl diffusion in plagioclase, because the plagioclase crystal must change its composition to produce albite-rich cotectic melts. Diffusion in the solid also affects the chemical composition of the melts. During initial melting, potassium is preferentially extracted from plagioclase because K-Na diffusion in plagioclase is faster than that of NaSi-CaAl. This also causes a shift in the cotectic compositions. Above the “critical temperature”, on the other hand, melting is promoted by a metastable reaction in which the plagioclase composition does not change, and which produces melts with compositional gradients along the original An60-diopside tie line. The critical temperature is determined by the intersection of the cotectic and the An60-diopside tie line. Interdiffusion coefficients of plagioclase-diopside components in the melt are estimated from melting rates above the critical temperature by using a simplified steady-state diffusion model (e.g., 10-8 cm2/sec at 1,300° C). Many examples of reaction zones due to partial melting have been described as spongy or fingerprint-like textures in xenoliths. Metastable melting above the critical temperature is considered to take place in natural melting where there is a high degree of melting. However, we cannot exclude the possibility of disequilibrium created by sluggish melting controlled by diffusion in the minerals. If melting occurs close to the solidus, this process can be important even for partial melting in the upper mantle.

Electromagnetic and Microwave Absorption Properties of the Flake-Shaped Pr-Ho-Fe Alloys in the C-Band

NASA Astrophysics Data System (ADS)

Luo, Jialiang; Pan, Shunkang; Qiao, Ziqiang; Cheng, Lichun; Wang, Zhenzhong; Lin, Peihao; Chang, Junqing

2018-01-01

The polycrystalline samples Pr x Ho2- x Fe17 ( x = 0.0, 0.1, 0.2, 0.3, 0.4) were prepared by arc melting and high-energy ball milling method. The influences of Pr substitution on phase structure, morphology, saturation magnetization and electromagnetic parameters were investigated by x-ray diffraction, scanning electron microscopy, vibrating-sample magnetometry and vector network analyzer, respectively. The results show that the particle size increased and the saturation magnetization decreased with increasing Pr content. The minimum absorption peak frequency shifted towards a lower-frequency region with increasing Pr concentration. The minimum RL of Pr0.3Ho1.7Fe17 powder was -41.03 dB at 6.88 GHz with a coating thickness of 2.0 mm. With different thickness of 1.8-2.8 mm, the minimum reflection loss (RL) of Pr0.3Ho1.7Fe17 powder was less than -20 dB in the whole C-band (4-8 GHz). The microwave-absorbing properties of the composite with different weight ratios of Pr0.3Ho1.7Fe17/Co were researched. The microwave-absorbing peaks of the composites shifted to a lower frequency with increasing Co content. The minimum RL of Pr0.3Ho1.7Fe17/Co(10%) was -42.51 dB at 4.72 GHz with a coating thickness of 2.6 mm. This suggests that the Pr-Ho-Fe will be a promising microwave absorption material in higher-gigahertz frequency, especially in the C-band.

Magmatic infiltration and melting in the lower crust and upper mantle beneath the Cima volcanic field, California

USGS Publications Warehouse

Wilshire, H.G.; McGuire, A.V.

1996-01-01

Xenoliths of lower crustal and upper mantle rocks from the Cima volcanic field (CVF) commonly contain glass pockets, veins, and planar trains of glass and/or fluid inclusions in primary minerals. Glass pockets occupy spaces formerly occupied by primary minerals of the host rocks, but there is a general lack of correspondence between the composition of the glass and that of the replaced primary minerals. The melting is considered to have been induced by infiltration of basaltic magma and differentiates of basaltic magma from complex conduits formed by hydraulic fracturing of the mantle and crustal rocks, and to have occurred during the episode of CVF magmatism between ???7.5 Ma and present. Variable compositions of quenched melts resulted from mixing of introduced melts and products of melting of primary minerals, reaction with primary minerals, partial crystallization, and fractionation resulting from melt and volatile expulsion upon entrainment of the xenoliths. High silica melts (> ??? 60% SiO2) may result by mixing introduced melts with siliceous melts produced by reaction of orthopyroxene. Other quenched melt compositions range from those comparable to the host basalts to those with intermediate Si compositions and elevated Al, alkalis, Ti, P, and S; groundmass compositions of CVF basalts are consistent with infiltration of fractionates of those basalts, but near-solidus melting may also contribute to formation of glass with intermediate silica contents with infiltration only of volatile constituents.

Characterization of Mullite-Zirconia Composite Processed by Non-Transferred and Transferred Arc Plasma

NASA Astrophysics Data System (ADS)

Yugeswaran, S.; Selvarajan, V.; Lusvarghi, L.; I. Y. Tok, A.; D. Siva Rama, Krishna

2009-04-01

The arc plasma melting technique is a simple method to synthesize high temperature reaction composites. In this study, mullite-zirconia composite was synthesized by transferred and non-transferred arc plasma melting, and the results were compared. A mixture of alumina and zircon powders with a mole ratio of 3: 2 were ball milled for four hours and melted for two minutes in the transferred and non-transferred mode of plasma arcs. Argon and air were used as plasma forming gases. The phase and microstructural formation of melted samples were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). The microstructure of the composites was found to be affected by the mode of melting. In transferred arc melting, zirconia flowers with uniform lines along with mullite whiskers were obtained. In the case of non-transferred arc plasma melting, mullite whiskers along with star shape zirconia were formed. Differential thermal analysis (DTA) of the synthesized mullite-zirconia composites provided a deeper understanding of the mechanisms of mullite formation during the two different processes.

Integrated melt inclusion and crystal zoning study to track the timescales and pre-eruption dynamics of violent Strombolian eruptions at Llaima volcano, Chile

NASA Astrophysics Data System (ADS)

Ruth, D. C.; Costa Rodriguez, F.; Bouvet de Maisonneuve, C.; Calder, E. S.

2013-12-01

Melt inclusion compositions in crystals from many volcanic systems are notoriously variable and some times difficult to interpret. Their compositions can be a combination of rapid crystal growth, entrapment of local melt, and diffusive re-equilibration, among other processes. Additionally, chemical zoning in olivine records changing environmental conditions, most importantly temperature and magma composition. Many geochemical studies focus on either melt inclusion data or chemical zoning data to ascertain volcanic processes. Here we combine melt inclusion data with that of chemical zoning of the olivine host crystals from the 2008 violent Strombolian eruption of Llaima volcano, Chile, to obtain a more refined understanding of the processes related to crystal growth, melt inclusion formation, and magma dynamics. We investigated zoning characteristics in a suite of olivine crystals, created X-ray element maps (Al, Ca, Mg, P, Fe), and collected quantitative elemental abundances across chemical zones for detailed diffusion modeling. Melt inclusion compositions were collected via electron microprobe analysis and LA-ICPMS. We observe three types of zoning in the host olivine crystals: normal, reverse, and multiple zones with fluctuating Fo content. Reverse zoning was more common than the other types. Regardless of zoning character, multiple melt inclusions are present within a given olivine, often found near the crystal rim. For some of these melt inclusions, the olivine surrounding the melt inclusion was also zoned, often to a similar composition as the olivine rim. This implies that these inclusions remained connected with interstitial matrix melt until melt inclusion closure. These ';open' melt inclusions exhibited slightly different major (higher SiO2, Na2O+K2O, TiO2) and trace elements (positive Eu and Sr anomalies) compared to melt inclusions in the same olivine that were not surrounded by compositional zoning. Quantitative elemental profiles produce modeled timescales on the order of 10s-100s days prior to eruption. Zoning textures, melt inclusion compositions, and timescale modeling indicates that crystal dissolution (open melt inclusions), mafic magma injection (reverse zoning), and partial melting of upper crustal plagioclase-rich cumulates (positive Eu and Sr anomalies) were occurring in the months prior to the 2008 eruption. The combination of both melt inclusion data and textural data of the host crystals provides deeper insight into the nature and timing of deep and shallow reservoir processes that generate violent Strombolian eruptions at Llaima.

The Origin of Mercury's Surface Composition, an Experimental Investigation

NASA Technical Reports Server (NTRS)

Boujibar, A.; Righter, K.; Rapp, J. F.; Ross, D. K.; Pando, K. M.; Danielson, L. R.; Fontaine, E.

2016-01-01

Introduction: Results from MESSENGER spacecraft have confirmed the reduced nature of Mercury, based on its high core/mantle ratio and its FeO-poor and S-rich surface. Moreover, high resolution images revealed large volcanic plains and abundant pyroclastic deposits, suggesting major melting stages of the Mercurian mantle. In addition, MESSENGER has provided the most precise data to date on major elemental compositions of Mercury's surface. These results revealed considerable chemical heterogeneities that suggested several stages of differentiation and re-melting processes. This interpretation was challenged by our experimental previous study, which showed a similar compositional variation in the melting products of enstatite chondrites, which are a possible Mercury analogue. However, these experimental melts were obtained over a limited range of pressure (1 bar to 1 gigapascal) and were not compared to the most recent elemental maps. Therefore, here we extend the experimental dataset to higher pressures and perform a more quantitative comparison with Mercury's surface compositions measured by MESSENGER. In particular, we test whether these chemical heterogeneities result from mixing between polybaric melts. Our experiments and models show that the majority of chemical diversity of Mercury's surface can result from melting of a primitive mantle compositionally similar to enstatite chondrites in composition at various depths and degrees of melting. The high-Mg region's composition is reproduced by melting at high pressure (3 gigapascals) (Tab. 1), which is consistent with previous interpretation as being a large degraded impact basin based on its low elevation and thin average crust. While low-Mg NVP (North Volcanic Plains) are the result of melting at low pressure (1 bar), intermediate-Mg NVP, Caloris Basin and Rachmaninoff result from mixing of a high-pressure (3 gigapascals) and low-pressure components (1 bar for Rachmaninoff and 1 gigapascal for the other regions) (Tab. 1). Moreover, all compositions suggest mixing between low and high degree melts that indicate important differentiation processes.

The effects of sulfide composition on the solubility of sulfur in coexisting silicate melts

NASA Astrophysics Data System (ADS)

Smythe, Duane; Wood, Bernard; Kiseeva, Ekaterina

2016-04-01

The extent to which sulfur dissolves in silicate melts saturated in an immiscible sulfide phase is a fundamental question in igneous petrology and plays a primary role in the generation of magmatic ore deposits, volcanic degassing and planetary differentiation. Terrestrial sulfide melts often contain over 20 weight percent Ni + Cu, however, most experimental studies investigating sulfur solubility in silicate melt have been primarily concerned with the effects of silicate melt composition, and pure FeS has been use as the immiscible sulfide melt (O'Neill and Mavrogenes, 2002; Li and Ripley, 2005). To investigation of the effects of sulfide composition, in addition to those of temperature, pressure and silicate melt composition, on sulfur solubility in silicate melts, we have carried out a series of experiments done at pressures between 1.5 and 3 GPa and temperatures from 1400 to 1800C over a range of compositions of both the silicate and sulfide melt. We find that the solubility of sulfur in silicate melts drops significantly with the substitution of Ni and Cu for Fe in the immiscible sulfide melt, decreasing by approximately 40% at mole fractions of NiS + Cu2S of 0.4. Combining our results with those from the previous studies investigating sulfur solubility in silicate melts we have also found that solubility increases with increasing temperature and decreases pressure. These results show that without considering the composition of the immiscible sulfide phase the sulfur content of silicate melts can be significantly overestimated. This may serve to explain the relatively low sulfur concentrations in MORB melts, which previous models predict to be undersaturated in a sulfide phase despite showing chemical and textural evidence for sulfide saturation. Li, C. & Ripley, E. M. (2005). Empirical equations to predict the sulfur content of mafic magmas at sulfide saturation and applications to magmatic sulfide deposits. Mineralium Deposita 40, 218-230. O'Neill, H. S. C. & Mavrogenes, J. A. (2002). The Sulfide Capacity and the Sulfur Content at Sulfide Saturation of Silicate Melts at 1400°C and 1 bar. Journal of Petrology 43, 1049-1087.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmitt, Adam K.; Mahanthappa, Mahesh K.

Using a combination of small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), we document the composition-dependent morphologies of 39 new poly(lactide-block-1,4-butadiene-block-lactide) (LBL) block polymers, comprising a broad dispersity B segment (Mn = 4.5–17.7 kg/mol;more » $$\\def\\eth{{\\specialfont\\char238}}$$ = Mw/Mn = 1.72–1.88) and narrow dispersity L end blocks (Mn = 0.6–15.3 kg/mol; $$\\def\\eth{{\\specialfont\\char238}}$$ = 1.10–1.21) with volume fractions 0.26 ≤ fB ≤ 0.95. A subset of these samples undergo melt self-assembly into cylindrical, lamellar, and apparently bicontinuous morphologies. By assessing the states of order and disorder in these triblock polymer melts using temperature-dependent SAXS, we find that broad B segment dispersity increases the minimum segregation strength χN ≳ 27 required for LBL triblock self-assembly relative to the self-consistent mean-field theory prediction χN ≥ 17.9 for narrow dispersity analogues. While B segment dispersity has previously been shown to thermodynamically stabilize the self-assembled morphologies of low χ/high N ABA triblocks, the present study indicates that broad B block dispersity in related high χ/low N systems destabilizes the microphase-separated melt. These observations are rationalized in terms of recent theories that suggest that broad segmental dispersity substantially enhances fluctuation effects at low N, thus disfavoring melt segregation.« less

Short-term hot hardness characteristics of rolling-element steels

NASA Technical Reports Server (NTRS)

Chevalier, J. L.; Dietrich, M. W.; Zaretsky, E. V.

1972-01-01

Short-term hot hardness studies were performed with five vacuum-melted steels at temperatures from 294 to 887 K (70 to 1140 F). Based upon a minimum Rockwell C hardness of 58, the temperature limitation on all materials studied was dependent on the initial room temperature hardness and the tempering temperature of each material. For the same room temperature hardness, the short-term hot hardness characteristics were identical and independent of material composition. An equation was developed to predict the short-term hardness at temperature as a function of initial room temperature hardness for AISI 52100, as well as the high-speed tool steels.

Semiconductor crystal growth and segregation problems on earth and in space

NASA Technical Reports Server (NTRS)

Gatos, H. C.

1982-01-01

Semiconductor crystal growth and segregation problems are examined in the context of their relationship to material properties, and some of the problems are illustrated with specific experimental results. The compositional and structural defects encountered in semiconductors are largely associated with gravity-induced convective currents in the melt; additional problems are introduced by variations in stoichiometry. It is demonstrated that in near-zero gravity environment, crystal growth and segregation takes place under ideal steady-state conditions with minimum convective interference. A discussion of the advantages of zero-gravity crystal growth is followed by a summary of problems arising from the absence of gravitational forces.

Method of producing particulate-reinforced composites and composites produced thereby

DOEpatents

Han, Qingyou; Liu, Zhiwei

2013-12-24

A process for producing particle-reinforced composite materials through utilization of an in situ reaction to produce a uniform dispersion of a fine particulate reinforcement phase. The process includes forming a melt of a first material, and then introducing particles of a second material into the melt and subjecting the melt to high-intensity acoustic vibration. A chemical reaction initiates between the first and second materials to produce reaction products in the melt. The reaction products comprise a solid particulate phase, and the high-intensity acoustic vibration fragments and/or separates the reaction products into solid particles that are dispersed in the melt and are smaller than the particles of the second material. Also encompassed are particle-reinforced composite materials produced by such a process.

Method of producing particulate-reinforced composites and composites produced thereby

DOEpatents

Han, Qingyou; Liu, Zhiwei

2015-12-29

A process for producing particle-reinforced composite materials through utilization of an in situ reaction to produce a uniform dispersion of a fine particulate reinforcement phase. The process includes forming a melt of a first material, and then introducing particles of a second material into the melt and subjecting the melt to high-intensity acoustic vibration. A chemical reaction initiates between the first and second materials to produce reaction products in the melt. The reaction products comprise a solid particulate phase, and the high-intensity acoustic vibration fragments and/or separates the reaction products into solid particles that are dispersed in the melt and are smaller than the particles of the second material. Also encompassed are particle-reinforced composite materials produced by such a process.

Compositions of Mars Rocks: SNC Meteorites, Differentiates, and Soils

NASA Technical Reports Server (NTRS)

Rutherford, M. J.; Minitti, M.; Weitz, C. M.

1999-01-01

The 13 samples from Mars identified in the terrestrial meteorite collections vary from dunite to pyroxenite to microgabbro or basalt. All of these rocks appear to have formed from primitive melts with similar major element compositional characteristics; i.e., FeO-rich and Al2O3-Poor melts relative to terrestrial basalt compositions. Although all of the SNC rocks can be derived by melting of the same Al-depleted mantle, contamination of SNC's by a Rb-enriched mantle or crustal source is required to explain the different REE characteristics of SNC rocks. Thus, there are indications of an old crustal rocktype on Mars, and this rock does not appear to have been sampled. This paper focuses primarily on the composition of the SNC basalts, however, and on the compositions of rocks which could be derived from SNC basaltic melt by magmatic processes. In particular, we consider the possible compositions which could be achieved through accumulation of early-formed crystals in the SNC primitive magma. Through a set of experiments we have determined (1) melt (magma) compositions which could be produced by melt evolution as crystals are removed from batches of this magma cooling at depth, and (2) which evolved (Si02enriched, MgO-depleted) rock compositions could be produced from the SNC magma, and how these compare with the Pathfinder andesite composition. Finally, we compare the SNC magma compositions to the Mars soil composition in order to determine whether any source other than SNC is required.

Multicomponent homogeneous alloys and method for making same

DOEpatents

Dutta, Partha S.; Miller, Thomas R.

2003-09-02

The present application discloses a method for preparing a homogeneous ternary or quaternary alloy from a quaternary melt. The method includes providing a family of phase diagrams for the quaternary melt which shows (i) composition/temperature data, (ii) tie lines connecting equilibrium liquid and solid compositions, and (iii) isotherms representing boundaries of a miscibility gap. Based on the family of phase diagrams, a quaternary melt composition and an alloy growth temperature is selected. A quaternary melt having the selected quaternary melt composition is provided and a ternary or quaternary alloy is grown from the quaternary melt at the selected alloy growth temperature. A method for making homogeneous ternary or quaternary alloy from a ternary or quaternary melt is also disclosed, as are homogeneous quaternary single-crystal alloys which are substantially free from crystal defects and which have the formula A.sub.x B.sub.1-x C.sub.y D.sub.1-y, x and y being the same or different and in the range of 0.001 to 0.999.

Thermal and mass implications of magmatic evolution in the Lassen volcanic region, California, and minimum constraints on basalt influx to the lower crust

USGS Publications Warehouse

Guffanti, M.; Clynne, M.A.; Muffler, L.J.P.

1996-01-01

We have analyzed the heat and mass demands of a petrologic model of basaltdriven magmatic evolution in which variously fractionated mafic magmas mix with silicic partial melts of the lower crust. We have formulated steady state heat budgets for two volcanically distinct areas in the Lassen region: the large, late Quaternary, intermediate to silicic Lassen volcanic center and the nearby, coeval, less evolved Caribou volcanic field. At Caribou volcanic field, heat provided by cooling and fractional crystallization of 52 km3 of basalt is more than sufficient to produce 10 km3 of rhyolitic melt by partial melting of lower crust. Net heat added by basalt intrusion at Caribou volcanic field is equivalent to an increase in lower crustal heat flow of ???7 mW m-2, indicating that the field is not a major crustal thermal anomaly. Addition of cumulates from fractionation is offset by removal of erupted partial melts. A minimum basalt influx of 0.3 km3 (km2 Ma)-1 is needed to supply Caribou volcanic field. Our methodology does not fully account for an influx of basalt that remains in the crust as derivative intrusives. On the basis of comparison to deep heat flow, the input of basalt could be ???3 to 7 times the amount we calculate. At Lassen volcanic center, at least 203 km3 of mantle-derived basalt is needed to produce 141 km3 of partial melt and drive the volcanic system. Partial melting mobilizes lower crustal material, augmenting the magmatic volume available for eruption at Lassen volcanic center; thus the erupted volume of 215 km3 exceeds the calculated basalt input of 203 km3. The minimum basalt input of 1.6 km3 (km2 Ma)-1 is >5 times the minimum influx to the Caribou volcanic field. Basalt influx high enough to sustain considerable partial melting, coupled with locally high extension rate, is a crucial factor in development of Lassen volcanic center; in contrast. Caribou volcanic field has failed to develop into a large silicic center primarily because basalt supply there has been insufficient.

Electron-Beam Atomic Spectroscopy for In Situ Measurements of Melt Composition for Refractory Metals: Analysis of Fundamental Physics and Plasma Models

NASA Astrophysics Data System (ADS)

Gasper, Paul Joseph; Apelian, Diran

2015-04-01

Electron-beam (EB) melting is used for the processing of refractory metals, such as Ta, Nb, Mo, and W. These metals have high value and are critical to many industries, including the semiconductor, aerospace, and nuclear industries. EB melting can also purify secondary feedstock, enabling the recovery and recycling of these materials. Currently, there is no method for measuring melt composition in situ during EB melting. Optical emission spectroscopy of the plasma generated by EB impact with vapor above the melt, a technique here termed electron-beam atomic spectroscopy, can be used to measure melt composition in situ, allowing for analysis of melt dynamics, facilitating improvement of EB melting processes and aiding recycling and recovery of these critical and high-value metals. This paper reviews the physics of the plasma generation by EB impact by characterizing the densities and energies of electrons, ions, and neutrals, and describing the interactions between them. Then several plasma models are introduced and their suitability to this application analyzed. Lastly, a potential method for calibration-free composition measurement is described and the challenges for implementation addressed.

The structural role and homogeneous redox equilibria of iron in peraluminous, metaluminous and peralkaline silicate melts

NASA Astrophysics Data System (ADS)

Dickenson, M. P.; Hess, P. C.

1986-02-01

The compositional dependence of the redox ratio (FeO/FeO1.5) has been experimentally determined in K2O-Al2O3-SiO2-Fe2O3-FeO (KASFF) and K2O-CaO-Al2O3-SiO2-Fe2O3-FeO (KCASFF) silicate melts. Compositions were equilibrated at 1,450° C in air, with 78 mol % SiO2. KASFF melts have from 1 to 5 mol % Fe2O3 and include both peraluminous (K2OAl2O3) compositions. KCASFF melts have 1 mol % Fe2O3 encompassing peraluminous, metaluminous (CaO+K2O>Al2O3) and peralkaline compositions. Peralkaline KASFF melts with 1 mol % Fe2O3 have low and constant values for the redox ratio, whereas in peraluminous melts the redox ratio increases with increasing (K2O/Al2O3). Increasing total iron concentration increases the redox ratio in peraluminous melts and slightly decreases the redox ratio in peralkaline melts. Substituting CaO for K2O at fixed total iron (1 mol %) increases the redox ratio in both peraluminous and metaluminous KCASFF melts; however, the redox ratio in peralkaline KCASFF melts is not affected by this exchange. These data indicate that Fe3+ is in four-fold coordination, with K+ or Ca2+ providing local charge balance. The tetrahedral ferric species is most stable in peralkaline melts and least stable in peraluminous melts, due to the competition between Al3+ and Fe3+ for charge balancing cations in the latter melt. Tetrahedral Fe3+ is also less stable when Ca2+ provides local charge balance. The data are consistent with a network modifying role for Fe2+ in the melt. The data are interpreted to reflect the effects of melt composition on the partitioning of K+ and Ca2+ and Fe3+ and Al3+ between various species in the melt. These relationships are discussed in terms of homogeneous equilibria between various iron-bearing and iron-free melt species. The results also reflect the effect of liquid composition on the exchange potentials μFe3+ Al-1 and μCa0.5K-1. The exchange potentials are relatively constant in peralkaline melts, but decrease in metaluminous and peraluminous melts as both (CaO+K2O)/(CaO+K2O+Al2O3) and K2O/CaO decrease. These qualitative observations imply that minerals exhibiting these exchanges will also be similarly affected as liquid composition changes.

Low-pressure differentiation of tholeiitic lavas as recorded in segregation veins from Reykjanes (Iceland), Lanzarote (Canary Islands) and Masaya (Nicaragua)

NASA Astrophysics Data System (ADS)

Martin, E.; Sigmarsson, O.

2007-11-01

Segregation veins are common in lava sheets and result from internal differentiation during lava emplacement and degassing. They consist of evolved liquid, most likely replaced by gas-filter pressing from a ˜50% crystallised host lava. Pairs of samples, host lavas and associated segregation veins from the Reykjanes Peninsula (Iceland), Lanzarote (Canary Islands) and the Masaya volcano (Nicaragua) show extreme mineralogical and compositional variations (MgO in host lava, segregation veins and interstitial glass ranges from 8-10 wt%, 3-6 wt%, and to less than 0.01 wt%, respectively). These samples allow the assessment of the internal lava flow differentiation mechanism, since both the parental and derived liquid are known in addition to the last magma drops in the form of late interstitial glasses. The mineralogical variation, mass-balance calculated from major- and trace element composition, and transitional metal partition between crystals and melts are all consistent with fractional crystallisation as the dominant differentiation mechanism. The interstitial glasses are highly silicic (SiO2 = 70-80 wt%) and represent a final product of high-degree (75-97%) fractional crystallisation of olivine tholeiite at a pressure close to one atmosphere. The tholeiitic liquid-line-of-decent and the composition of the residual melts are governed by the K2O/Na2O of the initial basaltic magma. The granitic minimum is reached if the initial liquid has a high K2O/Na2O whereas trondhjemitic composition is the final product of magma with low initial K2O/Na2O.

Abrasive wear response of TIG-melted TiC composite coating: Taguchi approach

NASA Astrophysics Data System (ADS)

Maleque, M. A.; Bello, K. A.; Adebisi, A. A.; Dube, A.

2017-03-01

In this study, Taguchi design of experiment approach has been applied to assess wear behaviour of TiC composite coatings deposited on AISI 4340 steel substrates by novel powder preplacement and TIG torch melting processes. To study the abrasive wear behaviour of these coatings against alumina ball at 600° C, a Taguchi’s orthogonal array is used to acquire the wear test data for determining optimal parameters that lead to the minimization of wear rate. Composite coatings are developed based on Taguchi’s L-16 orthogonal array experiment with three process parameters (welding current, welding speed, welding voltage and shielding gas flow rate) at four levels. In this technique, mean response and signal-to-noise ratio are used to evaluate the influence of the TIG process parameters on the wear rate performance of the composite coated surfaces. The results reveal that welding voltage is the most significant control parameter for minimizing wear rate while the current presents the least contribution to the wear rate reduction. The study also shows the best optimal condition has been arrived at A3 (90 A), B4 (2.5 mm/s), C3 (30 V) and D3 (20 L/min), which gives minimum wear rate in TiC embedded coatings. Finally, a confirmatory experiment has been conducted to verify the optimized result and shows that the error between the predicted values and the experimental observation at the optimal condition lies within the limit of 4.7 %. Thus, the validity of the optimum condition for the coatings is established.

Large-Scale Impact Cratering and Early Earth Evolution

NASA Technical Reports Server (NTRS)

Grieve, R. A. F.; Cintala, M. J.

1997-01-01

The surface of the Moon attests to the importance of large-scale impact in its early crustal evolution. Previous models of the effects of a massive bombardment on terrestrial crustal evolution have relied on analogies with the Moon, with allowances for the presence of water and a thinner lithosphere. It is now apparent that strict lunar-terrestrial analogies are incorrect because of the "differential scaling" of crater dimensions and melt volumes with event size and planetary gravity. Impact melt volumes and "ancient cavity dimensions for specific impacts were modeled according to previous procedures. In the terrestrial case, the melt volume (V(sub m)) exceeds that of the transient cavity (V(sub tc)) at diameters > or = 400 km. This condition is reached on the Moon only with transient cavity diameters > or = 3000 km, equivalent to whole Moon melting. The melt volumes in these large impact events are minimum estimates, since, at these sizes, the higher temperature of the target rocks at depth will increase melt production. Using the modification-scaling relation of Croft, a transient cavity diameter of about 400 km in the terrestrial environment corresponds to an expected final impact "basin" diameter of about 900 km. Such a "basin" would be comparable in dimensions to the lunar basin Orientale. This 900-km "basin" on the early Earth, however, would not have had the appearance of Orientale. It would have been essentially a melt pool, and, morphologically, would have had more in common with the palimpsests structures on Callisto and Ganymede. With the terrestrial equivalents to the large multiring basins of the Moon being manifested as muted palimpsest-like structures filled with impact melt, it is unlikely they played a role in establishing the freeboard on the early Earth. The composition of the massive impact melt sheets (> 10 (exp 7) cu km) produced in "basin-forming" events on the early Earth would have most likely ranged from basaltic to more mafic for the largest impacts, where the melt volume would have reached well into the mantle. Any contribution from adiabatic melting or shock heating of the asthenosphere would have had similar mafic compositions. The depth of the melt sheets is unknown but would have been in the multilkilometer range. Bodies of basaltic melt > or = 300 m thick differentiate in the terrestrial environment, with the degree of differentiation being a function of the thickness of the body. We therefore expect that these thick, closed-system melt pools would have differentiated into an ultramafic-mafic base and felsic top. If only 10% of the impact melt produced in a single event creating a 400-km diameter transient cavity evolved into felsic differentiates, they would be comparable in volume to the Columbia River basalts. It has been estimated that at least 200 impact events of this size or larger occurred on the early Earth during a period of heavy bombardment. We speculate that these massive differentiated melt sheets may have had a role in the formation of the initial felsic component of the Earth's crust. Additional information is contained in the original.

Temperature and composition dependencies of trace element partitioning - Olivine/melt and low-Ca pyroxene/melt

NASA Technical Reports Server (NTRS)

Colson, R. O.; Mckay, G. A.; Taylor, L. A.

1988-01-01

This paper presents a systematic thermodynamic analysis of the effects of temperature and composition on olivine/melt and low-Ca pyroxene/melt partitioning. Experiments were conducted in several synthetic basalts with a wide range of Fe/Mg, determining partition coefficients for Eu, Ca, Mn, Fe, Ni, Sm, Cd, Y, Yb, Sc, Al, Zr, and Ti and modeling accurately the changes in free energy for trace element exchange between crystal and melt as functions of the trace element size and charge. On the basis of this model, partition coefficients for olivine/melt and low-Ca pyroxene/melt can be predicted for a wide range of elements over a variety of basaltic bulk compositions and temperatures. Moreover, variations in partition coeffeicients during crystallization or melting can be modeled on the basis of changes in temperature and major element chemistry.

Pb-free Sn-Ag-Cu ternary eutectic solder

DOEpatents

Anderson, Iver E.; Yost, Frederick G.; Smith, John F.; Miller, Chad M.; Terpstra, Robert L.

1996-06-18

A Pb-free solder includes a ternary eutectic composition consisting essentially of about 93.6 weight % Sn-about 4.7 weight % Ag-about 1.7 weight % Cu having a eutectic melting temperature of about 217.degree. C. and variants of the ternary composition wherein the relative concentrations of Sn, Ag, and Cu deviate from the ternary eutectic composition to provide a controlled melting temperature range (liquid-solid "mushy" zone) relative to the eutectic melting temperature (e.g. up to 15.degree. C. above the eutectic melting temperature).

Pb-free Sn-Ag-Cu ternary eutectic solder

DOEpatents

Anderson, I.E.; Yost, F.G.; Smith, J.F.; Miller, C.M.; Terpstra, R.L.

1996-06-18

A Pb-free solder includes a ternary eutectic composition consisting essentially of about 93.6 weight % Sn-about 4.7 weight % Ag-about 1.7 weight % Cu having a eutectic melting temperature of about 217 C and variants of the ternary composition wherein the relative concentrations of Sn, Ag, and Cu deviate from the ternary eutectic composition to provide a controlled melting temperature range (liquid-solid ``mushy`` zone) relative to the eutectic melting temperature (e.g. up to 15 C above the eutectic melting temperature). 5 figs.

Experimental constraints on mantle metasomatism caused by silicate and carbonate melts

NASA Astrophysics Data System (ADS)

Gervasoni, Fernanda; Klemme, Stephan; Rohrbach, Arno; Grützner, Tobias; Berndt, Jasper

2017-06-01

Metasomatic processes are responsible for many of the heterogeneities found in the upper mantle. To better understand the metasomatism in the lithospheric mantle and to illustrate the differences between metasomatism caused by hydrous silicate and carbonate-rich melts, we performed various interaction experiments: (1) Reactions between hydrous eclogite-derived melts and peridotite at 2.2-2.5 GPa and 900-1000 °C reproduce the metasomatism in the mantle wedge above subduction zones. (2) Reactions between carbonate-rich melts and peridotite at 2.5 GPa and 1050-1000 °C, and at 6 GPa and 1200-1250 °C simulate metasomatism of carbonatite and ultramafic silicate-carbonate melts in different regions of cratonic lithosphere. Our experimental results show that partial melting of hydrous eclogite produces hydrous Si- and Al-rich melts that react with peridotite and form bi-mineralic assemblages of Al-rich orthopyroxene and Mg-rich amphibole. We also found that carbonate-rich melts with different compositions react with peridotite and form new metasomatic wehrlitic mineral assemblages. Metasomatic reactions caused by Ca-rich carbonatite melt consume the primary peridotite and produce large amounts of metasomatic clinopyroxene; on the other hand, metasomatism caused by ultramafic silicate-carbonate melts produces less clinopyroxene. Furthermore, our experiments show that ultramafic silicate-carbonate melts react strongly with peridotite and cause crystallization of large amounts of metasomatic Fe-Ti oxides. The reactions of metasomatic melts with peridotite also change the melt composition. For instance, if the carbonatite melt is not entirely consumed during the metasomatic reactions, its melt composition may change dramatically, generating an alkali-rich carbonated silicate melt that is similar in composition to type I kimberlites.

Coupling geodynamic with thermodynamic modelling for reconstructions of magmatic systems

NASA Astrophysics Data System (ADS)

Rummel, Lisa; Kaus, Boris J. P.; White, Richard

2016-04-01

Coupling geodynamic with petrological models is fundamental for understanding magmatic systems from the melting source in the mantle to the point of magma crystallisation in the upper crust. Most geodynamic codes use very simplified petrological models consisting of a single, fixed, chemistry. Here, we develop a method to better track the petrological evolution of the source rock and corresponding volcanic and plutonic rocks by combining a geodynamic code with a thermodynamic model for magma generation and evolution. For the geodynamic modelling a finite element code (MVEP2) solves the conservation of mass, momentum and energy equations. The thermodynamic modelling of phase equilibria in magmatic systems is performed with pMELTS for mantle-like bulk compositions. The thermodynamic dependent properties calculated by pMELTS are density, melt fraction and the composition of the liquid and solid phase in the chemical system: SiO2-TiO2-Al2O3-Fe2O3-Cr2O3-FeO-MgO-CaO-Na2O-K2O-P2O5-H2O. In order to take into account the chemical depletion of the source rock with increasing melt extraction events, calculation of phase diagrams is performed in two steps: 1) With an initial rock composition density, melt fraction as well as liquid and solid composition are computed over the full upper mantle P-T range. 2) Once the residual rock composition (equivalent to the solid composition after melt extraction) is significantly different from the initial rock composition and the melt fraction is lower than a critical value, the residual composition is used for next calculations with pMELTS. The implementation of several melt extraction events take the change in chemistry into account until the solidus is shifted to such high temperatures that the rock cannot be molten anymore under upper mantle conditions. An advantage of this approach is that we can track the change of melt chemistry with time, which can be compared with natural constraints. In the thermo-mechanical code the thermodynamic dependent properties from pre-computed phase diagrams are carried by each particle using marker-in-cell method . Thus the physical and chemical properties can change locally as a function of previous melt extraction events, pressure and temperature conditions. After each melt extraction event, the residual rock composition is compared with the bulk composition of previous computed phase diagrams, so that the used phase diagram is replaced by the phase diagram with the closest bulk chemistry. In the thermo-mechanical code, the melt is extracted directly to the surface as volcanites and within the crust as plutonites. The density of the crust and new generated crust is calculated with the thermodynamic modelling tool Perple_X. We have investigated the influence of several input parameters on the magma composition to compare it with real rock samples from Eifel (West-Germany). In order to take the very inhomogeneous chemistry of European mantle into account, we include not only primitive mantle but also metasomatised mantle fragments in the melting source of a plume (Eifel plume).

Is EETA79001 Lithology B A True Melt Composition?

NASA Technical Reports Server (NTRS)

Arauza, S. J.; Jones, John H.; Mittlefehldt, D. W.; Le, L.

2010-01-01

EETA79001 is a member of the SNC (shergottite, nakhlite, chassignite) group of Martian meteorites. Most SNC meteorites are cumulates or partial cumulates [1] inhibiting calculation of parent magma compositions; only two (QUE94201 and Y- 980459) have been previously identified as true melt compositions. The goal of this study is to test whether EETA79001-B may also represent an equilibrium melt composition, which could potentially expand the current understanding of martian petrology.

Melts of garnet lherzolite: experiments, models and comparison to melts of pyroxenite and carbonated lherzolite

USGS Publications Warehouse

Grove, Timothy L.; Holbig, Eva S.; Barr, Jay A.; Till, Christy B.; Krawczynski, Michael J.

2013-01-01

Phase equilibrium experiments on a compositionally modified olivine leucitite from the Tibetan plateau have been carried out from 2.2 to 2.8 GPa and 1,380–1,480 °C. The experiments-produced liquids multiply saturated with spinel and garnet lherzolite phase assemblages (olivine, orthopyroxene, clinopyroxene and spinel ± garnet) under nominally anhydrous conditions. These SiO2-undersaturated liquids and published experimental data are utilized to develop a predictive model for garnet lherzolite melting of compositionally variable mantle under anhydrous conditions over the pressure range of 1.9–6 GPa. The model estimates the major element compositions of garnet-saturated melts for a range of mantle lherzolite compositions and predicts the conditions of the spinel to garnet lherzolite phase transition for natural peridotite compositions at above-solidus temperatures and pressures. We compare our predicted garnet lherzolite melts to those of pyroxenite and carbonated lherzolite and develop criteria for distinguishing among melts of these different source types. We also use the model in conjunction with a published predictive model for plagioclase and spinel lherzolite to characterize the differences in major element composition for melts in the plagioclase, spinel and garnet facies and develop tests to distinguish between melts of these three lherzolite facies based on major elements. The model is applied to understand the source materials and conditions of melting for high-K lavas erupted in the Tibetan plateau, basanite–nephelinite lavas erupted early in the evolution of Kilauea volcano, Hawaii, as well as younger tholeiitic to alkali lavas from Kilauea.

Oxygen isotope geochemistry of mafic magmas at Mt. Vesuvius

NASA Astrophysics Data System (ADS)

Dallai, Luigi; Raffaello, Cioni; Chiara, Boschi; Claudia, D'oriano

2010-05-01

Pumice and scoria from different eruptive layers of Mt. Vesuvius volcanic products contain mafic minerals consisting of High-Fo olivine and Diopsidic Pyroxene. These phases were crystallized in unerupted trachibasaltic to tephritic magmas, and were brought to surface by large phonolitic/tephri-phonolitic (e.g. Avellino and Pompei) and/or of tephritic and phono-tephritic (Pollena) eruptions. A large set of these mm-sized crystals was accurately separated from selected juvenile material and measured for their chemical compositions (EPMA, Laser Ablation ICP-MS) and 18O/16O ratios (conventional laser fluorination) to constrain the nature and evolution of the primary magmas at Mt. Vesuvius. Uncontaminated mantle δ18O values are hardly recovered in Italian Quaternary magmas, mostly due to the widespread occurrence of crustal contamination of the primary melts during their ascent to the surface (e.g. Alban Hills, Ernici Mts., and Aeolian Islands). At Mt. Vesuvius, measured olivine and clinopyroxene share quite homogeneous chemical compositions (Olivine Fo 85-90 ; Diopside En 45-48, respectively), and represent phases crystallized in near primary mafic magmas. Trace element composition constrains the near primary nature of the phases. Published data on volatile content of melt inclusions hosted in these crystals reveal the coexistence of dissolved water and carbon dioxide, and a minimum trapping pressure around 200-300 MPa, suggesting that crystal growth occurred in a reservoir at about 8-10 km depth. Recently, experimental data have suggested massive carbonate assimilation (up to about 20%) to derive potassic alkali magmas from trachybasaltic melts. Accordingly, the δ18O variability and the trace element content of the studied minerals suggest possible contamination of primary melts by an O-isotope enriched, REE-poor contaminant like the limestone of Vesuvius basement. Low, nearly primitive δ18O values are observed for olivine from Pompeii eruption, although still above the range of typical mantle minerals. The δ18Oolivine and δ18Ocpxof the minerals from all the studied eruptions define variable degrees of carbonate interaction and magma crystallization for the different eruptions, and possibly within the same eruption, and show evidence of oxygen isotope equilibrium at high temperature. However, energy-constrained AFC model suggest that carbonate assimilation was limited. On the basis of our data, we suggest that interaction between magma and a fluxing, decarbonation-derived CO2 fluid may be partly accounted for the measured O-isotope compositions.

An Approach to Processable Polyimides

NASA Technical Reports Server (NTRS)

Gariepy, Christopher A.; Eby, R. K.; Meador, Michael A.

1999-01-01

The use of polymer matrix composites (PMC's) in aircraft engines can lead to substantial weight savings over metals. This weight reduction correlates into better fuel economy, increased speed, and increased passenger load. Typically, high performance PMC's possess high thermal-oxidative stabilities (TOS) and high glass transition temperatures (Tg's) to withstand temperatures up to 316 C (600 F). One of the leading high temperature resins system available today is PMR-15 (Polymerization of Monomeric Reactants, MW=1500). This thermosetting polyimide utilizes addition curing through polymer endcaps which enables hand lay-up processing of carbon fiber composite parts with low void contents. However, the large amount of hand labor raises manufacturing costs and prohibits the use of PMR-15 in many aerospace applications. Resin Transfer Molding (RTM) provides an economical alternative, but it requires a melt Viscosity of less than 10(exp 3) centipoise (cP). This is much lower than the minimum melt viscosity of PMR-15 (about 10(exp 6) cP). To improve the processability of polyimides, the polymer backbone can be modified by incorporating flexible linkages, such as branching. bulky pendant groups, kinked structures, and twisted or non-coplanar moietes . The focus of this paper will be the introduction of non-coplanar biaryls into the PMR polyimide backbone to increase processability while maintaining high temperature performance.

A compositional tipping point governing the mobilization and eruption style of rhyolitic magma

NASA Astrophysics Data System (ADS)

di Genova, D.; Kolzenburg, S.; Wiesmaier, S.; Dallanave, E.; Neuville, D. R.; Hess, K. U.; Dingwell, D. B.

2017-12-01

The most viscous volcanic melts and the largest explosive eruptions on our planet consist of calcalkaline rhyolites. These eruptions have the potential to influence global climate. The eruptive products are commonly very crystal-poor and highly degassed, yet the magma is mostly stored as crystal mushes containing small amounts of interstitial melt with elevated water content. It is unclear how magma mushes are mobilized to create large batches of eruptible crystal-free magma. Further, rhyolitic eruptions can switch repeatedly between effusive and explosive eruption styles and this transition is difficult to attribute to the rheological effects of water content or crystallinity. Here we measure the viscosity of a series of melts spanning the compositional range of the Yellowstone volcanic system and find that in a narrow compositional zone, melt viscosity increases by up to two orders of magnitude. These viscosity variations are not predicted by current viscosity models and result from melt structure reorganization, as confirmed by Raman spectroscopy. We identify a critical compositional tipping point, independently documented in the global geochemical record of rhyolites, at which rhyolitic melts fluidize or stiffen and that clearly separates effusive from explosive deposits worldwide. This correlation between melt structure, viscosity and eruptive behaviour holds despite the variable water content and other parameters, such as temperature, that are inherent in natural eruptions. Thermodynamic modelling demonstrates how the observed subtle compositional changes that result in fluidization or stiffening of the melt can be induced by crystal growth from the melt or variation in oxygen fugacity. However, the rheological effects of water and crystal content alone cannot explain the correlation between composition and eruptive style. We conclude that the composition of calcalkaline rhyolites is decisive in determining the mobilization and eruption dynamics of Earth’s largest volcanic systems, resulting in a better understanding of how the melt structure controls volcanic processes.

A compositional tipping point governing the mobilization and eruption style of rhyolitic magma.

PubMed

Di Genova, D; Kolzenburg, S; Wiesmaier, S; Dallanave, E; Neuville, D R; Hess, K U; Dingwell, D B

2017-12-13

The most viscous volcanic melts and the largest explosive eruptions on our planet consist of calcalkaline rhyolites. These eruptions have the potential to influence global climate. The eruptive products are commonly very crystal-poor and highly degassed, yet the magma is mostly stored as crystal mushes containing small amounts of interstitial melt with elevated water content. It is unclear how magma mushes are mobilized to create large batches of eruptible crystal-free magma. Further, rhyolitic eruptions can switch repeatedly between effusive and explosive eruption styles and this transition is difficult to attribute to the rheological effects of water content or crystallinity. Here we measure the viscosity of a series of melts spanning the compositional range of the Yellowstone volcanic system and find that in a narrow compositional zone, melt viscosity increases by up to two orders of magnitude. These viscosity variations are not predicted by current viscosity models and result from melt structure reorganization, as confirmed by Raman spectroscopy. We identify a critical compositional tipping point, independently documented in the global geochemical record of rhyolites, at which rhyolitic melts fluidize or stiffen and that clearly separates effusive from explosive deposits worldwide. This correlation between melt structure, viscosity and eruptive behaviour holds despite the variable water content and other parameters, such as temperature, that are inherent in natural eruptions. Thermodynamic modelling demonstrates how the observed subtle compositional changes that result in fluidization or stiffening of the melt can be induced by crystal growth from the melt or variation in oxygen fugacity. However, the rheological effects of water and crystal content alone cannot explain the correlation between composition and eruptive style. We conclude that the composition of calcalkaline rhyolites is decisive in determining the mobilization and eruption dynamics of Earth's largest volcanic systems, resulting in a better understanding of how the melt structure controls volcanic processes.

Role of crystallizational differention in the origin of island-arc andesitic melts: evidence from data on melt inclusions and oxygen isotopes

NASA Astrophysics Data System (ADS)

Krasheninnikov, S. P.; Portnyagin, M.; Bindeman, I. N.; Bazanova, L. I.

2012-12-01

Several recent studies of melt inclusions in island-arc rocks revealed a strong bimodality of the melt compositions at the predominance of basic and silicic melts and the scarcity of intermediate melts with SiO2=59-66 wt% (e.g. [1]). These observations were used to interpret the origin of island-arc andesites by magma mingling, crustal assimilation and crystal accumulation rather than by fractional crystallization of basaltic magmas. In this work we addressed the question about the scarcity of andesitic melts in island-arc setting by systematic study of bulk compositions, melt inclusions and oxygen isotopes in minerals from Avachinskiy volcano in Kamchatka. We studied ~500 melt inclusions in 6 different mineral phases (Ol, Cpx, Opx, Pl, Amph, Mt), and concentrated on rapidly-quenched tephra samples from 40 Holocene eruptions of andesites and basaltic andesites. The melt inclusions span a large range of compositions from basalts to rhyolites. In comparison with host bulk tephra samples, melt inclusions tend to have more silicic compositions (up to 10 wt% of SiO2), and this disparity tend to increase with increasing SiO2 content in the host rocks. Both melt inclusion and host rock compositions form trends along the line dividing low- and middle-K island-arc series, and variations of major elements are continuous, without apparent bimodality, which is observed in data set from [1]. The MI statistical distribution is rather three-modal with maxima at ~56-58, ~66 and 74 wt% of SiO2. Much of the major element variability in MI can be explained by fractional crystallization from parental basaltic melts using numerical modeling of crystallization path. Magnetite crystallization starts at ~58 wt% of SiO2 and affects significantly on the evolutional path of melts. Abundant crystallization of magnetite lead to formation of more silica rich coexistent melts and change of crystallizing assemblage occurred at ~60 wt% of SiO2, when Opx replaced Ol, and Amph and Ap become stable. Paragenesis of OPx, CPx, Amph, Pl, Mt, Ilm and Ap dominated the following evolution of melts toward strongly acid compositions with 78-80 wt% SiO2. Individual Pl and Amph crystals are in magmatic isotopic equilibrium, have heavy δ18O values increasing from 6.3 ‰ in basaltic andesites to 7.1 ‰ in andesites, suggesting that magmatic evolution started from primary high-d18O basalt likely related to the abundant high-d18O sources described for Kamchatkan primitive magmas. The oxygen isotopic data support the conclusion that island-arc andesitic melts of Avachinsky Volcano generate predominantly due to the processes of fractional crystallization of high-d18O. The new data on composition of melt inclusions allowed us to reconstruct the entire spectrum of parental melts for Avacha volcano. Melt inclusions in different minerals form coherent trends of major elements, which can be well explained by fractional crystallization. Unlike some other island-arc volcanoes, Avachinskiy melts do not display clear bimodality of SiO2 content. Melts of intermediate compositions are relatively abundant and found in minerals from basaltic andesites. [1] Reuby & Blundy (2009) Nature, 461(7268), 1269-1273.

Properties of the Guin ungrouped iron meteorite - The origin of Guin and of group-IIE irons

NASA Astrophysics Data System (ADS)

Rubin, A. E.; Jerde, E. A.; Zong, P.; Wasson, J. T.; Westcott, J. W.; Mayeda, T. K.; Clayton, R. N.

1986-01-01

The composition and structure of the Guin ungrouped iron meteorite inclusions have been investigated experimentally. The structural characteristics of polished and etched slabs of the meteorite were studied microscopically in reflected light. Modal abundances of troilite nodules and silicate inclusions were determined by weighing paper traces. The bulk composition of the silicate inclusions was calculated by combining modal phase abundances and mineral compositions. It is found that the largest silicate inclusion (2 x 4 cm) consists mostly of a shock-melted plagioclase-rich matrix surrounding large, partly melted augite grains. The oxygen isotopic composition of the inclusion is near that of LL chondrites. The inclusion is found to be similar in composition to selected melt pocket glasses in ordinary chondrites produced in situ by preferential melting of plagioclase rock due to shock compression. It is suggested that the Guin assemblage was formed by impact melting on a chondritic parent body. Silicate inclusions in IIE irons share many of the compositional and petrological characteristics of the Guin inclusions, indicating that IIE irons also formed by impact-melting of chondritic materials. Black and white photomicrographs of the silicate inclusions are provided.

Controls on melting at spreading ridges from correlated abyssal peridotite - mid-ocean ridge basalt compositions

NASA Astrophysics Data System (ADS)

Regelous, Marcel; Weinzierl, Christoph G.; Haase, Karsten M.

2016-09-01

Variations in the volume and major element composition of basalt erupted along the global mid-ocean ridge system have been attributed to differences in mantle potential temperature, mantle composition, or plate spreading rate and lithosphere thickness. Abyssal peridotites, the residues of mantle melting beneath mid-ocean ridges, provide additional information on the melting process, which could be used to test these hypotheses. We compiled a global database of abyssal peridotite compositions averaged over the same ridge segments defined by Gale et al. (2013). In addition, we calculated the distance of each ridge segment to the nearest hotspots. We show that Cr# in spinel in abyssal peridotites is negatively correlated with Na90 in basalts from the same ridge segments on a global scale. Ridge segments that erupt basalts apparently produced by larger degrees of mantle melting are thus underlain by peridotites from which large amounts of melt have been extracted. We find that near-ridge hotspots have a more widespread influence on mid-ocean ridge basalt (MORB) composition and ridge depth than previously thought. However, when these hotspot-influenced ridge segments are excluded, the remaining segments show clear relationships between MORB composition, peridotite composition, and ridge depth with spreading rate. Very slow-spreading ridges (<20 mm/yr) are deeper, erupt basalts with higher Na90, Al90, K90/Ti90, and lower Fe90, Ca90/Al90, and expose peridotites with lower Cr# than intermediate and fast-spreading ridges. We show that away from hotspots, the spreading-rate dependence of the maximum degree of mantle melting inferred from Cr# in peridotites (FM) and the bulk degree of melting inferred from Na90 in basalts (FB) from the same ridge segments is unlikely to be due to variations in mantle composition. Nor can the effects of dynamic mantle upwelling or incomplete melt extraction at low spreading rates satisfactorily explain the observed compositions of abyssal peridotites and MORB from very slow-spreading ridges. Instead, the distinctive compositions of abyssal peridotites and MORB from very slow-spreading ridges could result from the presence of a thick lithospheric lid, leading to a lower average degree of melting, and a higher contribution to melting from more fertile mantle lithologies. Alternatively, spreading rate influences the thermal structure of the upper mantle such that the mantle beneath very slow-spreading ridges is cooler.

Melt Inclusions Record Extreme Compositional Variability in Primitive Magmas at Mauna Loa Volcano, Hawaii

NASA Astrophysics Data System (ADS)

Kamenetsky, V. S.; Norman, M. D.; Garcia, M. O.

2002-12-01

Melt inclusions carry potentially unique information about magmatic processes and the compositional evolution of erupted lavas. Major element compositions of olivine-hosted melt inclusions in submarine tholeiitic picrites from the southwest rift zone of Mauna Loa volcano have been studied to examine the compositional variability of primitive magmas feeding the world's largest volcano. Approximately 600 naturally quenched inclusions were examined from 8 samples with 3-25 vol% olivine phenocrysts and 9-22 wt% MgO. Olivine compositions ranged from Fo91-Fo82. The inclusions show a continuous variation in FeO contents from near-magmatic values (9 to 11 wt%) in the most evolved olivines to extremely low values (3.5 to 7.0 wt%) in the most primitive olivines. This appears to reflect a complex magmatic history for these crystals involving extensive re-equlibration of melts trapped by early formed phenocrysts with their host olivine. Extreme compositional variability also characterizes incompatible elements that would not be affected by equilibration with the host olivine. Inclusions trapped in relatively primitive olivines (Fo88-91) show a large range of K2O contents (0.1 to 2.1 wt%), whereas inclusions in more evolved olivines converge on whole rock compositions with 0.3 to 0.4 wt% K2O. Similarly, TiO2/K2O, Na2O/K2O, and K2O/P2O5 ratios of inclusions in primitive olivines span a much larger range than do inclusions hosted by more evolved olivines, with TiO2/K2O ratios extending from enriched to depleted compositions (1.2 to 24.7) in primitive olivines, and converging on whole rock compositions (TiO2/K2O = 6-9) in more evolved host olivine. This points toward extreme compositional variability in melts feeding Mauna Loa, and effective mixing of these melt parcels in the shallower summit reservoir to produce the restricted range of whole rock compositions sampled by erupted lavas. Whole rock compositions, therefore provide an integrated view of melting and high-level mixing processes, whereas melt inclusions provide more detailed information about source characteristics.

Duration of the Arctic sea ice melt season: Regional and interannual variability, 1979-2001

USGS Publications Warehouse

Belchansky, G.I.; Douglas, David C.; Platonov, Nikita G.

2004-01-01

Melt onset dates, freeze onset dates, and melt season duration were estimated over Arctic sea ice, 1979–2001, using passive microwave satellite imagery and surface air temperature data. Sea ice melt duration for the entire Northern Hemisphere varied from a 104-day minimum in 1983 and 1996 to a 124-day maximum in 1989. Ranges in melt duration were highest in peripheral seas, numbering 32, 42, 44, and 51 days in the Laptev, Barents-Kara, East Siberian, and Chukchi Seas, respectively. In the Arctic Ocean, average melt duration varied from a 75-day minimum in 1987 to a 103-day maximum in 1989. On average, melt onset in annual ice began 10.6 days earlier than perennial ice, and freeze onset in perennial ice commenced 18.4 days earlier than annual ice. Average annual melt dates, freeze dates, and melt durations in annual ice were significantly correlated with seasonal strength of the Arctic Oscillation (AO). Following high-index AO winters (January–March), spring melt tended to be earlier and autumn freeze later, leading to longer melt season durations. The largest increases in melt duration were observed in the eastern Siberian Arctic, coincident with cyclonic low pressure and ice motion anomalies associated with high-index AO phases. Following a positive AO shift in 1989, mean annual melt duration increased 2–3 weeks in the northern East Siberian and Chukchi Seas. Decreasing correlations between consecutive-year maps of melt onset in annual ice during 1979–2001 indicated increasing spatial variability and unpredictability in melt distributions from one year to the next. Despite recent declines in the winter AO index, recent melt distributions did not show evidence of reestablishing spatial patterns similar to those observed during the 1979–88 low-index AO period. Recent freeze distributions have become increasingly similar to those observed during 1979–88, suggesting a recurrent spatial pattern of freeze chronology under low-index AO conditions.

Temperature constraints on the Ginkgo flow of the Columbia River Basalt Group

NASA Astrophysics Data System (ADS)

Ho, Anita M.; Cashman, Katharine V.

1997-05-01

This study provides the first quantitative estimate of heat loss for a Columbia River Basalt Group flow. A glass composition-based geothermometer was experimentally calibrated for a composition representative of the 500-km-long Ginkgo flow of the Columbia River Basalt Group to measure temperature change during transport. Melting experiments were conducted on a bulk sample at 1 atm between 1200 and 1050 °C. Natural glass was sampled from the margin of a feeder dike near Kahlotus, Washington, and from pillow basalt at distances of 120 km (Vantage, Washington), 350 km (Molalla, Oregon), and 370 km (Portland, Oregon). Ginkgo basalt was also sampled at its distal end at Yaquina Head, Oregon (500 km). Comparison of the glass MgO content, K2O in plagioclase, and measured crystallinities in the experimental charges and natural samples tightly constrains the minimum flow temperature to 1085 ± 5 °C. Glass and plagioclase compositions indicate an upper temperature of 1095 ± 5 °C; thus the maximum temperature decrease along the flow axis of the Ginkgo is 20 °C, suggesting cooling rates of 0.02 0.04 °C/km. These cooling rates, substantially lower than rates observed in active and historic flows, are inconsistent with turbulent flow models. Calculated melt temperatures and viscosities of 240 750 Pa · s allow emplacement either as a fast laminar flow under an insulating crust or as a slower, inflated flow.

Global variations in abyssal peridotite compositions

NASA Astrophysics Data System (ADS)

Warren, Jessica M.

2016-04-01

Abyssal peridotites are ultramafic rocks collected from mid-ocean ridges that are the residues of adiabatic decompression melting. Their compositions provide information on the degree of melting and melt-rock interaction involved in the formation of oceanic lithosphere, as well as providing constraints on pre-existing mantle heterogeneities. This review presents a compilation of abyssal peridotite geochemical data (modes, mineral major elements, and clinopyroxene trace elements) for > 1200 samples from 53 localities on 6 major ridge systems. On the basis of composition and petrography, peridotites are classified into one of five lithological groups: (1) residual peridotite, (2) dunite, (3) gabbro-veined and/or plagioclase-bearing peridotite, (4) pyroxenite-veined peridotite, and (5) other types of melt-added peridotite. Almost a third of abyssal peridotites are veined, indicating that the oceanic lithospheric mantle is more fertile, on average, than estimates based on residual peridotites alone imply. All veins appear to have formed recently during melt transport beneath the ridge, though some pyroxenites may be derived from melting of recycled oceanic crust. A limited number of samples are available at intermediate and fast spreading rates, with samples from the East Pacific Rise indicating high degrees of melting. At slow and ultra-slow spreading rates, residual abyssal peridotites define a large (0-15% modal clinopyroxene and spinel Cr# = 0.1-0.6) compositional range. These variations do not match the prediction for how degree of melting should vary as a function of spreading rate. Instead, the compositional ranges of residual peridotites are derived from a combination of melting, melt-rock interaction and pre-existing compositional variability, where melt-rock interaction is used here as a general term to refer to the wide range of processes that can occur during melt transport in the mantle. Globally, 10% of abyssal peridotites are refractory (0% clinopyroxene, spinel Cr# > 0.5, bulk Al2O3 < 1 wt.%) and some ridge sections are dominated by harzburgites while lacking a significant basaltic crust. Abyssal ultramafic samples thus indicate that the mantle is multi-component, probably consisting of at least three components (lherzolite, harzburgite, and pyroxenite). Overall, the large compositional range among residual and melt-added peridotites implies that the oceanic lithospheric mantle is heterogeneous, which will lead to the generation of further heterogeneities upon subduction back into the mantle.

Melting of metasomatized peridotite at 4-6 GPa and up to 1200 °C: an experimental approach

NASA Astrophysics Data System (ADS)

Kessel, R.; Pettke, T.; Fumagalli, P.

2015-04-01

The phase assemblages and compositions in a K-bearing lherzolite + H2O system are determined between 4 and 6 GPa and 850-1200 °C, and the melting reactions occurring at subarc depth in subduction zones are constrained. Experiments were performed on a rocking multi-anvil apparatus. The experiments had around 16 wt% water content, and hydrous melt or aqueous fluid was segregated and trapped in a diamond aggregate layer. The compositions of the aqueous fluid and hydrous melt phases were measured using the cryogenic LA-ICP-MS technique. The residual lherzolite consists of olivine, orthopyroxene, clinopyroxene, and garnet, while diamond (C) is assumed to be inert. Hydrous and alkali-rich minerals were absent from the run products due to preferred dissolution of K2O (and Na2O) to the aqueous fluid/hydrous melt phases. The role of phlogopite in melting relations is, thus, controlled by the water content in the system: at the water content of around 16 wt% used here, phlogopite is unstable and thus does not participate in melting reactions. The water-saturated solidus, i.e., the first appearance of hydrous melt in the K-lherzolite composition, is located between 900 and 1000 °C at 4 GPa and between 1000 and 1100 °C at 5 and 6 GPa. Compositional jumps between hydrous melt and aqueous fluid at the solidus include a significant increase in the total dissolved solids load. All melts/fluids are peralkaline and calcium-rich. The melting reactions at the solidus are peritectic, as olivine, clinopyroxene, garnet, and H2O are consumed to generate hydrous melt plus orthopyroxene. Our fluid/melt compositional data demonstrate that the water-saturated hybrid peridotite solidus lies above 1000 °C at depths greater than 150 km and that the second critical endpoint is not reached at 6 GPa for a K2O-Na2O-CaO-FeO-MgO-Al2O3-SiO2-H2O-Cr2O3(-TiO2) peridotite composition.

Effect of process parameters on the density and porosity of laser melted AlSi10Mg/SiC metal matrix composite

NASA Astrophysics Data System (ADS)

Famodimu, Omotoyosi H.; Stanford, Mark; Oduoza, Chike F.; Zhang, Lijuan

2018-06-01

Laser melting of aluminium alloy—AlSi10Mg has increasingly been used to create specialised products in various industrial applications, however, research on utilising laser melting of aluminium matrix composites in replacing specialised parts have been slow on the uptake. This has been attributed to the complexity of the laser melting process, metal/ceramic feedstock for the process and the reaction of the feedstock material to the laser. Thus, an understanding of the process, material microstructure and mechanical properties is important for its adoption as a manufacturing route of aluminium metal matrix composites. The effects of several parameters of the laser melting process on the mechanical blended composite were thus investigated in this research. This included single track formations of the matrix alloy and the composite alloyed with 5% and 10% respectively for their reaction to laser melting and the fabrication of density blocks to investigate the relative density and porosity over different scan speeds. The results from these experiments were utilised in determining a process window in fabricating near-fully dense parts.

In situ study at high pressure and temperature of the environment of water in hydrous Na and Ca aluminosilicate melts and coexisting aqueous fluids

NASA Astrophysics Data System (ADS)

Le Losq, Charles; Dalou, Célia; Mysen, Bjorn O.

2017-07-01

The bonding and speciation of water dissolved in Na silicate and Na and Ca aluminosilicate melts were inferred from in situ Raman spectroscopy of the samples, in hydrothermal diamond anvil cells, while at crustal temperature and pressure conditions. Raman data were also acquired on Na silicate and Na and Ca aluminosilicate glasses, quenched from hydrous melts equilibrated at high temperature and pressure in a piston cylinder apparatus. In the hydrous melts, temperature strongly influences O-H stretching ν(O-H) signals, reflecting its control on the bonding of protons between different molecular complexes. Pressure and melt composition effects are much smaller and difficult to discriminate with the present data. However, the chemical composition of the melt + fluid system influences the differences between the ν(O-H) signals from the melts and the fluids and, hence, between their hydrogen partition functions. Quenching modifies the O-H stretching signals: strong hydrogen bonds form in the glasses below the glass transition temperature Tg, and this phenomenon depends on glass composition. Therefore, glasses do not necessarily record the O-H stretching signal shape in melts near Tg. The melt hydrogen partition function thus cannot be assessed with certainty using O-H stretching vibration data from glasses. From the present results, the ratio of the hydrogen partition functions of hydrous silicate melts and aqueous fluids mostly depends on temperature and the bulk melt + fluid system chemical composition. This implies that the fractionation of hydrogen isotopes between magmas and aqueous fluids in water-saturated magmatic systems with differences in temperature and bulk chemical composition will be different.

VOLATILECALC: A silicate melt-H2O-CO2 solution model written in Visual Basic for excel

USGS Publications Warehouse

Newman, S.; Lowenstern, J. B.

2002-01-01

We present solution models for the rhyolite-H2O-CO2 and basalt-H2O-CO2 systems at magmatic temperatures and pressures below ~ 5000 bar. The models are coded as macros written in Visual Basic for Applications, for use within MicrosoftR Excel (Office'98 and 2000). The series of macros, entitled VOLATILECALC, can calculate the following: (1) Saturation pressures for silicate melt of known dissolved H2O and CO2 concentrations and the corresponding equilibrium vapor composition; (2) open- and closed-system degassing paths (melt and vapor composition) for depressurizing rhyolitic and basaltic melts; (3) isobaric solubility curves for rhyolitic and basaltic melts; (4) isoplethic solubility curves (constant vapor composition) for rhyolitic and basaltic melts; (5) polybaric solubility curves for the two end members and (6) end member fugacities of H2O and CO2 vapors at magmatic temperatures. The basalt-H2O-CO2 macros in VOLATILECALC are capable of calculating melt-vapor solubility over a range of silicate-melt compositions by using the relationships provided by Dixon (American Mineralogist 82 (1997) 368). The output agrees well with the published solution models and experimental data for silicate melt-vapor systems for pressures below 5000 bar. ?? 2002 Elsevier Science Ltd. All rights reserved.

V OLATILEC ALC: a silicate melt-H 2O-CO 2 solution model written in Visual Basic for excel

NASA Astrophysics Data System (ADS)

Newman, Sally; Lowenstern, Jacob B.

2002-06-01

We present solution models for the rhyolite-H 2O-CO 2 and basalt-H 2O-CO 2 systems at magmatic temperatures and pressures below ˜5000 bar. The models are coded as macros written in Visual Basic for Applications, for use within Microsoft ® Excel (Office'98 and 2000). The series of macros, entitled V OLATILEC ALC, can calculate the following: (1) Saturation pressures for silicate melt of known dissolved H 2O and CO 2 concentrations and the corresponding equilibrium vapor composition; (2) open- and closed-system degassing paths (melt and vapor composition) for depressurizing rhyolitic and basaltic melts; (3) isobaric solubility curves for rhyolitic and basaltic melts; (4) isoplethic solubility curves (constant vapor composition) for rhyolitic and basaltic melts; (5) polybaric solubility curves for the two end members and (6) end member fugacities of H 2O and CO 2 vapors at magmatic temperatures. The basalt-H 2O-CO 2 macros in V OLATILEC ALC are capable of calculating melt-vapor solubility over a range of silicate-melt compositions by using the relationships provided by Dixon (American Mineralogist 82 (1997) 368). The output agrees well with the published solution models and experimental data for silicate melt-vapor systems for pressures below 5000 bar.

Trace Elements in Basalts From the Siqueiros Fracture Zone: Implications for Melt Migration Models

NASA Astrophysics Data System (ADS)

Pickle, R. C.; Forsyth, D. W.; Saal, A. E.; Nagle, A. N.; Perfit, M. R.

2008-12-01

Incompatible trace element (ITE) ratios in MORB from a variety of locations may provide insights into the melt migration process by constraining aggregated melt compositions predicted by mantle melting and flow models. By using actual plate geometries to create a 3-D thermodynamic mantle model, melt volumes and compositions at all depths and locations may be calculated and binned into cubes using the pHMELTS algorithm [Asimow et al., 2004]. These melts can be traced from each cube to the surface assuming several migration models, including a simplified pressure gradient model and one in which melt is guided upwards by a low permeability compacted layer. The ITE ratios of all melts arriving at the surface are summed, averaged, and compared to those of the actual sample compositions from the various MOR locales. The Siqueiros fracture zone at 8° 20' N on the East Pacific Rise (EPR) comprises 4 intra-transform spreading centers (ITSCs) across 140 km of offset between two longer spreading ridges, and is an excellent study region for several reasons. First, an abundance of MORB data is readily available, and the samples retrieved from ITSCs are unlikely to be aggregated in a long-lived magma chamber or affected by along-axis transport, so they represent melts extracted locally from the mantle. Additionally, samples at Siqueiros span a compositional range from depleted to normal MORB within the fracture zone yet have similar isotopic compositions to samples collected from the 9-10° EPR. This minimizes the effect of assuming a uniform source composition in our melting model despite a heterogeneous mantle, allowing us to consistently compare the actual lava composition with that predicted by our model. Finally, it has been demonstrated with preliminary migration models that incipient melts generated directly below an ITSC may not necessarily erupt at that ITSC but migrate laterally towards a nearby ridge due to enhanced pressure gradients. The close proximity of the ITSCs at Siqueiros to the large ridges bounding the fracture zone provide a good opportunity to model this phenomenon and may help explain the variable ITE ratios found between samples collected within the transform and those near the ridges.

Oxygen and U-Th isotopes and the timescales of hydrothermal exchange and melting in granitoid wall rocks at Mount Mazama, Crater Lake, Oregon

USGS Publications Warehouse

Ankney, Meagan E.; Bacon, Charles R.; Valley, John W.; Beard, Brian L.; Johnson, Clark M.

2017-01-01

We report new whole rock U-Th and in-situ oxygen isotope compositions for partially melted (0–50 vol% melt), low-δ18O Pleistocene granitoid blocks ejected during the ∼7.7 ka caldera-forming eruption of Mt. Mazama (Crater Lake, Oregon). The blocks are interpreted to represent wall rocks of the climactic magma chamber that, prior to eruption, experienced variable amounts of exchange with meteoric hydrothermal fluids and subsequent partial melting. U-Th and oxygen isotope results allow us to examine the timescales of hydrothermal circulation and partial melting, and provide an “outside in” perspective on the buildup to the climactic eruption of Mt. Mazama. Oxygen isotope compositions measured in the cores and rims of individual quartz (n = 126) and plagioclase (n = 91) crystals, and for transects across ten quartz crystals, document zonation in quartz (Δ18OCore-Rim ≤ 0.1–5.5‰), but show homogeneity in plagioclase (Δ18OCore-Rim ≤ ±0.8‰). We propose that oxygen isotope zonation in quartz records hydrothermal exchange followed by high-temperature exchange in response to partial melting caused by injection of basaltic to andesitic recharge magma into the deeper portions of the chamber. Results of modeling of oxygen diffusion in quartz indicates that hydrothermal exchange in quartz occurred over a period of ∼1000–63,000 years. Models also suggest that the onset of melting of the granitoids occurred a minimum of ∼10–200 years prior to the Mazama climactic eruption, an inference which is broadly consistent with results for magnetite homogenization and for Zr diffusion in melt previously reported by others.Uranium-thorium isotope compositions of most granitoid blocks are in 238U excess, and are in agreement with a 238U enriched array previously measured for volcanic rocks at Mt. Mazama. Uranium excess in the granitoids is likely due to enrichment via hydrothermal circulation, given their low δ18O values. The sample with the highest U excess (≥5.8%) also has the most 18O isotope depletion (average δ18Oplag = −4.0‰). The granitoids are a probable assimilant and source of U excess in volcanic rocks from Mt. Mazama. Two granitoids have Th excess and low δ18O values, interpreted to record leaching of U during hydrothermal alteration. A U-Th isochron based on the U excess array of the granitoids and volcanic rocks indicates that hydrothermal circulation initiated ∼40–75 kyrs before the climactic eruption, potentially marking the initiation of a persistent upper-crustal magma chamber. The U-Th ages are consistent with the maximum timescales inferred for hydrothermal alteration based on oxygen isotope zoning in quartz.

Hydrous partial melting in the sheeted dike complex at fast spreading ridges: experimental and natural observations

NASA Astrophysics Data System (ADS)

France, Lydéric; Koepke, Juergen; Ildefonse, Benoit; Cichy, Sarah B.; Deschamps, Fabien

2010-11-01

In ophiolites and in present-day oceanic crust formed at fast spreading ridges, oceanic plagiogranites are commonly observed at, or close to the base of the sheeted dike complex. They can be produced either by differentiation of mafic melts, or by hydrous partial melting of the hydrothermally altered sheeted dikes. In addition, the hydrothermally altered base of the sheeted dike complex, which is often infiltrated by plagiogranitic veins, is usually recrystallized into granoblastic dikes that are commonly interpreted as a result of prograde granulitic metamorphism. To test the anatectic origin of oceanic plagiogranites, we performed melting experiments on a natural hydrothermally altered dike, under conditions that match those prevailing at the base of the sheeted dike complex. All generated melts are water saturated, transitional between tholeiitic and calc-alkaline, and match the compositions of oceanic plagiogranites observed close to the base of the sheeted dike complex. Newly crystallized clinopyroxene and plagioclase have compositions that are characteristic of the same minerals in granoblastic dikes. Published silicic melt compositions obtained in classical MORB fractionation experiments also broadly match the compositions of oceanic plagiogranites; however, the compositions of the coexisting experimental minerals significantly deviate from those of the granoblastic dikes. Our results demonstrate that hydrous partial melting is a likely common process in the root zone of the sheeted dike complex, starting at temperatures exceeding 850°C. The newly formed melt can either crystallize to form oceanic plagiogranites or may be recycled within the melt lens resulting in hybridized and contaminated MORB melts. It represents the main MORB crustal contamination process. The residue after the partial melting event is represented by the granoblastic dikes. Our results support a model with a dynamic melt lens that has the potential to trigger hydrous partial melting reactions in the previously hydrothermally altered sheeted dikes. A new thermometer using the Al content of clinopyroxene is also elaborated.

Low-melting elemental metal or fusible alloy encapsulated polymerization initiator for delayed initiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermes, Robert E.

2017-08-15

An encapsulated composition for polymerization includes an initiator composition for initiating a polymerization reaction, and a capsule prepared from an elemental metal or fusible alloy having a melting temperature from about 20.degree. C. to about 200.degree. C. A fluid for polymerization includes the encapsulated composition and a monomer. When the capsule melts or breaks open, the initiator is released.

The Effect of Lithospheric Discontinuities on the Composition of Lavas From the Northern Galápagos Platform Extension

NASA Astrophysics Data System (ADS)

Schlitzer, W.; Harpp, K. S.; Mittelstaedt, E. L.; Kurz, M. D.; Geist, D.

2011-12-01

The platform supporting the Galápagos Archipelago extends ~50 km NW toward the Galápagos Spreading Center (GSC) into the Northern Galapagos Volcanic Province (NGVP), where it underlies Pinta, Marchena, and Genovesa Islands. Approximately 45 km north of Pinta is the southern termination of a ~100-km long transform fault, at 90o50'W. The seafloor surrounding the NGVP was surveyed and dredged during the 2010 MV1007 and 2001 DRIFT04 cruises. All the large volcanoes, including the islands, have elongate bathymetric footprints with extensive submarine ridges. Lavas from this small region (<150 km in diameter) exhibit isotopic and trace element signatures that span the compositional range of the entire Galápagos Archipelago. Pinta and its submarine extension have the most enriched signatures, whereas at the eastern end of the platform extension, Genovesa is indistinguishable from normal MORB. Samples dredged around Pinta and Marchena have intermediate compositions. In contrast, lavas from the adjacent transform fault are more depleted than those from Genovesa and anywhere along the GSC for hundreds of km in both directions. Lavas from this region exhibit a range of 3He/4He (6.5-9.5 Ra), significantly lower than the high 3He/4He signature of material erupted by the plume-rich western Galápagos shield volcanoes (>25 Ra). Whereas the compositions of lavas erupted on the Nazca Plate in the NGVP require 3 or more distinct mantle endmembers to explain their compositions, our data indicate that the platform extension region only requires components previously described for the Galápagos Islands. In addition, Sm/Yb decreases abruptly along an E-W transect from Pinta to Genovesa. Gibson and Geist (2010) concluded that Sm/Yb ratios reflect variations in surface wave velocities (Villagomez et al., 2007), enabling them to predict lithospheric thickness. We apply the relationship defined by Gibson and Geist to map lithospheric thickness across our study area. Our results suggest that the lithosphere (and thus minimum melt generation depth) gets progressively shallower from Pinta to Genovesa; this phenomenon may explain unexpected Holocene volcanism in the NGVP. The wide range in Sm/Yb further suggests a complex lithospheric structure underlying the platform extension, which we propose reflects formation of the adjacent GSC transform fault within the last ~3 Ma, possibly through a series of ridge jumps as suggested by modeling of new magnetic data. We propose a model in which heterogeneous plume material with enriched and depleted components (Ito and Mahoney, 2005) is migrating toward the GSC along the base of the lithosphere, having previously lost its primordial helium signature during deep melting near the western shield volcanoes. As the material crosses the complex lithospheric thickness variations in the NGVP, melt generation becomes progressively shallower. The enriched compositions at Pinta thus result from limited, deep melting of enriched compositions owing to a thick lithospheric cap. East of Pinta, the plume melts more extensively and to shallower depths, producing progressively depleted signatures toward Genovesa.

High porosity harzburgite and dunite channels for the transport of compositionally heterogeneous melts in the mantle: II. Geochemical consequences

NASA Astrophysics Data System (ADS)

Liang, Y.; Schiemenz, A.; Xia, Y.; Parmentier, E.

2009-12-01

In a companion numerical study [1], we explored the spatial distribution of high porosity harzburgite and dunite channels produced by reactive dissolution of orthopyroxene (opx) in an upwelling mantle column and identified a number of new features. In this study, we examine the geochemical consequences of channelized melt flow under the settings outlined in [1] with special attention to the transport of compositionally heterogeneous melts and their interactions with the surrounding peridotite matrix during melt migration in the mantle. Time-dependent transport equations for a trace element in the interstitial melt and solids that include advection, dispersion, and melt-rock reaction were solved in a 2-D upwelling column using the high-order numerical methods outlined in [1]. The melt and solid velocities were taken from the steady state or quasi-steady state solutions of [1]. In terms of trace element fractionation, the simulation domain can be divided into 4 distinct regions: (a) high porosity harzburgite channel, overlain by; (b) high porosity dunite channel; (c) low porosity compacting boundary layer surrounding the melt channels; and (d) inter-channel regions outside (c). In the limit of local chemical equilibrium, melting in region (d) is equivalent to batch melting, whereas melting and melt extraction in (c) is more close to fractional melting with the melt suction rate first increase from the bottom of the melting column to a maximum near the bottom of the dunite channel and then decrease upward in the compacting boundary layer. The melt composition in the high porosity harzburgite channel is similar to that produced by high-degree batch melting (up to opx exhaustion), whereas the melt composition in the dunite is a weighted average of the ultra-depleted melt from the harzburgite channel below, the expelled melt from the compacting boundary layer, and melt produced by opx dissolution along the sidewalls of the dunite channel. Compaction within the dunite channel drives part of the channel melt in the upper part of the dunite channel into the surrounding harzburgite, providing a physical mechanism for shallow level re-fertilization or mantle metasomatism. The presence of compacting waves in and around a dunite-harzburgite channel system further complicates the melt flow field and provides new mechanisms for melt-peridotite interaction in the mantle. In the presence of chemical heterogeneity, the assumption of local equilibrium between the melt and its surrounding crystals results in significant chromatographic fractionation for incompatible trace elements in the melt percolating in region (d), and moderate fractionation for melt flowing through the harzburgite channel. Chemical disequilibrium between the melt and crystals reduces the extent of chromatographic fractionation during melt percolation and may be needed to explain the observed geochemical data. Alternatively, compositionally heterogeneous melts may be extracted through the high porosity melt channels without interaction with the peridotite matrix. [1] Schiemenz et al. submitted to AGU Fall meeting, 2009.

Drilling constraints on bimodal volcanism and subsequent formation of contrasted uppermost crustal compositions at the middle Okinawa Trough

NASA Astrophysics Data System (ADS)

Yamasaki, T.; Takaya, Y.; Mukae, N.; Nagase, T.; Tindell, T.; Totsuka, S.; Uno, Y.; Yonezu, K.; Nozaki, T.; Ishibashi, J. I.; Kumagai, H.; Maeda, L.; Shipboard Scientist, C.

2016-12-01

The Okinawa Trough (OT) is a young and actively spreading back-arc basin, extending behind the Ryukyu arc-trench system in the southeastern margin of the East China Sea. The OT is believed to be in an initial rifting stage (starting from 6-9 Ma), prior to the normal/stable seafloor spreading which constitutes the main stage of back-arc basin formation. Two drilling cruises ‒ the IODP Exp. 331 and SIP CK14-04 D/V Chikyu Cruise (Exp. 907) in 2010 and 2014 ‒ were conducted at the Iheya North Knoll, middle OT. The Iheya North Knoll is a domal volcanic complex consisting of small volcanic bodies. On these cruises, pumiceous gravel and altered rhyolitic rocks, as well as hemi-pelagic sediments, hydrothermal clay and Kuroko-type ores, were recovered from the upper 200 m of the crust. From Feb. 11, 2016 to Mar. 17, 2016, the SIP CK16-01 (Exp. 908) D/V Chikyu cruise was conducted at Iheya North Knoll and the sediment-covered rifting center of the Iheya-Minor Ridge area, middle OT. The Iheya-Minor ridge area is also an active hydrothermal field, located 25 km southeast of the Iheya North Knoll. In this area, basaltic rocks are widely distributed, and drilling has confirmed that the basaltic materials continue to 120 m below the seafloor. From an igneous petrological point of view, the volcanic rocks in the Okinawa Trough are characterized by bimodal basaltic and rhyolitic compositions, with a compositional gap between SiO2 = 56-66 wt%. The origin of the rhyolitic rock has been interpreted as magmatic differentiation of basaltic magma. However, the existence of an active basalt-hosted hydrothermal field in the Iheya-Minor ridge area suggests the presence of hot basaltic rocks at a shallow position in the crust, and reaching recharged seawater at this depth. Furthermore, the composition of felsic rocks just after the compositional gap (SiO2 = 67 wt%) is very similar to that of the minimum melt of a granitic system, and experimental partial melt of hydrous basalt. Therefore, the contrast in the uppermost crustal composition between very close ( 25 km) areas can reasonably be explained by re-melting of hydrothermally-altered basaltic rocks and production of felsic magma at the upper crustal level, and direct eruption of basaltic magma at the seafloor.

Lithospheric thickness controlled compositional variations in potassic basalts of Northeast China by melt-rock interactions

NASA Astrophysics Data System (ADS)

Liu, Jian-Qiang; Chen, Li-Hui; Zeng, Gang; Wang, Xiao-Jun; Zhong, Yuan; Yu, Xun

2016-03-01

Melt-rock interaction is a common mantle process; however, it remains unclear how this process affects the composition of potassic basalt. Here we present a case study to highlight the link between compositional variations in the potassic basalts and melt-rock interaction in cold lithosphere. Cenozoic potassic basalts in Northeast China are strongly enriched in incompatible elements and show EM1-type Sr-Nd-Pb isotopes, suggesting an enriched mantle source. These rocks show good correlations between 87Sr/86Sr and K2O/Na2O and Rb/Nb. Notably, these ratios decrease with increasing lithospheric thickness, which may reflect melt-lithosphere interaction. Phlogopite precipitated when potassic melts passed through the lithospheric mantle, and K and Rb contents of the residual melts decreased over time. The thicker the lithosphere, the greater the loss of K and Rb from the magma. Therefore, the compositions of potassic basalts were controlled by both their enriched sources and reactions with lithospheric mantle.

Markov Chain Monte Carlo Inversion of Mantle Temperature and Composition, with Application to Iceland

NASA Astrophysics Data System (ADS)

Brown, Eric; Petersen, Kenni; Lesher, Charles

2017-04-01

Basalts are formed by adiabatic decompression melting of the asthenosphere, and thus provide records of the thermal, chemical and dynamical state of the upper mantle. However, uniquely constraining the importance of these factors through the lens of melting is challenging given the inevitability that primary basalts are the product of variable mixing of melts derived from distinct lithologies having different melting behaviors (e.g. peridotite vs. pyroxenite). Forward mantle melting models, such as REEBOX PRO [1], are useful tools in this regard, because they can account for differences in melting behavior and melt pooling processes, and provide estimates of bulk crust composition and volume that can be compared with geochemical and geophysical constraints, respectively. Nevertheless, these models require critical assumptions regarding mantle temperature, and lithologic abundance(s)/composition(s), all of which are poorly constrained. To provide better constraints on these parameters and their uncertainties, we have coupled a Markov Chain Monte Carlo (MCMC) sampling technique with the REEBOX PRO melting model. The MCMC method systematically samples distributions of key REEBOX PRO input parameters (mantle potential temperature, and initial abundances and compositions of the source lithologies) based on a likelihood function that describes the 'fit' of the model outputs (bulk crust composition and volume and end-member peridotite and pyroxenite melts) relative to geochemical and geophysical constraints and their associated uncertainties. As a case study, we have tested and applied the model to magmatism along Reykjanes Peninsula in Iceland, where pyroxenite has been inferred to be present in the mantle source. This locale is ideal because there exist sufficient geochemical and geophysical data to estimate bulk crust compositions and volumes, as well as the range of near-parental melts derived from the mantle. We find that for the case of passive upwelling, the models that best fit the geochemical and geophysical observables require elevated mantle potential temperatures ( 120 °C above ambient mantle), and 5% pyroxenite. The modeled peridotite source has a trace element composition similar to depleted MORB mantle, whereas the trace element composition of the pyroxenite is similar to enriched mid-ocean ridge basalt. These results highlight the promise of this method for efficiently exploring the range of mantle temperatures, lithologic abundances, and mantle source compositions that are most consistent with available observational constraints in individual volcanic systems. 1 Brown and Lesher (2016), G-cubed, 17, 3929-3968

Effect of modification of isotactic polypropylene by additives of polyamide 6/66 on structural characteristics of composites

NASA Astrophysics Data System (ADS)

Vorontsov, N. V.; Popov, A. A.; Margolin, A. L.

2017-12-01

Changes in the supramolecular structure of polymer composites based on isotactic polypropylene (PP) and polyamide 6/66 (PA) are studied depending on the PP : PA ratio. Temperatures and enthalpies of melting and crystallization of both PP and PA and their composites are determined depending on the composition of the mixtures. It was shown that the initial melting point of a composite does not change with increasing PA content in the blends. The crystallization temperature of the mixtures is shown to increase with the addition of PA and becomes much higher than the crystallization temperatures of both PP and PA. The observed effect can be due to a strong interaction between the PP and PA molecules, thus decreasing the molecular mobility and increasing the crystallization temperature. The crystallization and melting of PP-PA mixtures are found to proceed at the close temperatures, although the crystallization and melting temperatures of pure PP and pure PA differ widely. The melting and crystallization enthalpies decrease with increasing PA concentration in the mixtures, which indicates a decrease in the degree of crystallinity of the composite.

The Origin of the Compositional Diversity of Mercury's Surface Constrained From Experimental Melting of Enstatite Chondrites

NASA Technical Reports Server (NTRS)

Boujibar, A.; Righter, K.; Pando, K.; Danielson, L.

2015-01-01

Mercury is known as an endmember planet as it is the most reduced terrestrial planet with the highest core/mantle ratio. MESSENGER spacecraft has shown that its surface is FeO-poor (2-4 wt%) and Srich (up to 6-7 wt%), which confirms the reducing nature of its silicate mantle. Moreover, high resolution images revealed large volcanic plains and abundant pyroclastic deposits, suggesting important melting stages of the Mercurian mantle. This interpretation was confirmed by the high crustal thickness (up to 100 km) derived from Mercury's gravity field. This is also corroborated by a recent experimental result that showed that Mercurian partial melts are expected to be highly buoyant within the Mercurian mantle and could have risen from depths as high as the core-mantle boundary. In addition MESSENGER spacecraft provided relatively precise data on major elemental compositions of Mercury's surface. These results revealed important chemical and mineralogical heterogeneities that suggested several stages of differentiation and re-melting processes. However, the extent and nature of compositional variations produced by partial melting remains poorly constrained for the particular compositions of Mercury (very reducing conditions, low FeO-contents and high sulfur-contents). Therefore, in this study, we investigated the processes that lead to the various compositions of Mercury's surface. Melting experiments with bulk Mercury-analogue compositions were performed and compared to the compositions measured by MESSENGER.

Studies on Hot-Melt Prepregging on PRM-II-50 Polyimide Resin with Graphite Fibers

NASA Technical Reports Server (NTRS)

Shin, E. Eugene; Sutter, James K.; Juhas, John; Veverka, Adrienne; Klans, Ojars; Inghram, Linda; Scheiman, Dan; Papadopoulos, Demetrios; Zoha, John; Bubnick, Jim

2004-01-01

A second generation PMR (in situ Polymerization of Monomer Reactants) polyimide resin PMR-II-50, has been considered for high temperature and high stiffness space propulsion composites applications for its improved high temperature performance. As part of composite processing optimization, two commercial prepregging methods: solution vs. hot-melt processes were investigated with M40J fabrics from Toray. In a previous study a systematic chemical, physical, thermal and mechanical characterization of these composites indicated the poor resin-fiber interfacial wetting, especially for the hot-melt process, resulted in poor composite quality. In order to improve the interfacial wetting, optimization of the resin viscosity and process variables were attempted in a commercial hot-melt prepregging line. In addition to presenting the results from the prepreg quality optimization trials, the combined effects of the prepregging method and two different composite cure methods, i.e. hot press vs. autoclave on composite quality and properties are discussed.

Studies on Hot-Melt Prepregging of PMR-II-50 Polyimide Resin with Graphite Fibers

NASA Technical Reports Server (NTRS)

Shin, E. Eugene; Sutter, James K.; Juhas, John; Veverka, Adrienne; Klans, Ojars; Inghram, Linda; Scheiman, Dan; Papadopoulos, Demetrios; Zoha, John; Bubnick, Jim

2003-01-01

A Second generation PMR (in situ Polymerization of Monomer Reactants) polyimide resin, PMR-II-50, has been considered for high temperature and high stiffness space propulsion composites applications for its improved high temperature performance. As part of composite processing optimization, two commercial prepregging methods: solution vs. hot-melt processes were investigated with M40J fabrics from Toray. In a previous study a systematic chemical, physical, thermal and mechanical characterization of these composites indicated that poor resin-fiber interfacial wetting, especially for the hot-melt process, resulted in poor composite quality. In order to improve the interfacial wetting, optimization of the resin viscosity and process variables were attempted in a commercial hot-melt prepregging line. In addition to presenting the results from the prepreg quality optimization trials, the combined effects of the prepregging method and two different composite cure methods, i.e., hot press vs. autoclave on composite quality and properties are discussed.

Melting of the Primitive Mercurian Mantle, Insights into the Origin of Its Surface Composition

NASA Technical Reports Server (NTRS)

Boujibar, A.; Righter, K.; Rapp, J. F.; Ross, D. K.; Pando, K. M.; Danielson, L. R.; Fontaine, E.

2016-01-01

Recent findings of the MESSENGER mission on Mercury have brought new evidence for its reducing nature, widespread volcanism and surface compositional heteregeneity. MESSENGER also provided major elemental ratios of its surface that can be used to infer large-scale differentiation processes and the thermal history of the planet. Mercury is known as being very reduced, with very low Fe-content and high S and alkali contents on its surface. Its bulk composition is therefore likely close to EH enstatite chondrites. In order to elucidate the origin of the chemical diversity of Mercury's surface, we determined the melting properties of EH enstatite chondrites, at pressures between 1 bar and 3 GPa and oxygen fugacity of IW-3 to IW-5, using piston-cylinder experiments, combined with a previous study on EH4 melting at 1 bar. We found that the presence of Ca-rich sulfide melts induces significant decrease of Ca-content in silicate melts at low pressure and low degree of melting (F). Also at pressures lower than 3 GPa, the SiO2-content decreases with F, while it increases at 3 GPa. This is likely due to the chemical composition of the bulk silicate which has a (Mg+Fe+Ca)/Si ratio very close to 1 and to the change from incongruent to congruent melting of enstatite. We then tested whether the various chemical compositions of Mercury's surface can result from mixing between two melting products of EH chondrites. We found that the majority of the geochemical provinces of Mercury's surface can be explained by mixing of two melts, with the exception of the High-Al plains that require an Al-rich source. Our findings indicate that Mercury's surface could have been produced by polybaric melting of a relatively primitive mantle.

The effect of melt composition on the partitioning of trace elements between titanite and silicate melt

NASA Astrophysics Data System (ADS)

Prowatke, S.; Klemme, S.

2003-04-01

The aim of this study is to systematically investigate the influence of melt composition on the partitioning of trace elements between titanite and different silicate melts. Titanite was chosen because of its important role as an accessory mineral, particularly with regard to intermediate to silicic alkaline and calc-alkaline magmas [e.g. 1] and of its relative constant mineral composition over a wide range of bulk compositions. Experiments at atmospheric pressure were performed at temperatures between 1150°C and 1050°C. Bulk compositions were chosen to represent a basaltic andesite (SH3 - 53% SiO2), a dacite (SH2 - 65 SiO2) and a rhyolite (SH1 - 71% SiO2). Furthermore, two additional experimental series were conducted to investigate the effect of Al-Na and the Na-K ratio of melts on partitioning. Starting materials consisted of glasses that were doped with 23 trace elements including some selected rare earth elements (La, Ce, Pr, Sm, Gd, Lu), high field strength elements (Zr, Hf, Nb, Ta) and large ion lithophile elements (Cs, Rb, Ba) and Th and U. The experimental run products were analysed for trace elements using secondary ion mass spectrometry at Heidelberg University. Preliminary results indicate a strong effect of melt composition on trace element partition coefficients. Partition coefficients for rare-earth elements uniformly show a convex-upward shape [2, 3], since titanite accommodates the middle rare-earth elements more readily than the light rare-earth elements or the heavy rare-earth elements. Partition coefficients for the rare-earth elements follow a parabolic trend when plotted against ionic radius. The shape of the parabola is very similar for all studied bulk compositions, the position of the parabola, however, is strongly dependent on bulk composition. For example, isothermal rare-earth element partition coefficients (such as La) are incompatible (D<1) in alkali-rich silicate melts and strongly compatible (D>>1) in alkali-poor melt compositions. From our experimental data we present an model that combines the influence of the crystal lattice on partitioning with the effect of melt composition on trace element partition coefficients. [1] Nakada, S. (1991) Am. Mineral. 76: 548-560 [2] Green, T.H. and Pearson, N.J. (1986) Chem. Geol. 55: 105-119 [3] Tiepolo, M.; Oberti, R. and Vannucci, R. (2002) Chem. Geol. 191: 105-119

Oxidation and evaporation of sulfur species at atmospheric entry of iron sulfide fine particles

NASA Astrophysics Data System (ADS)

Isobe, H.; Murozono, K.

2017-12-01

Micrometeorites have the most abundant flux in current accumulation of planetary materials to the Earth. Micrometeorites are heated and reacted with upper atmosphere at atmospheric entry. Evaporation of meteoritic materials, especially sulfur species, may have environmental effect at upper atmosphere (e.g. Court and Sephton, 2011; Tomkins et al., 2016). Troilite is typical FeS phase in chondritic meteorites. In this study, quick heating and cooling experiments of FeS reagent particles were carried out with a fine particles free falling apparatus with controlled gas flow (Isobe and Gondo, 2013). Starting material reagent is inhomogeneous mixture of troilite, iron oxide and iron metal. Oxygen fugacity was controlled to FMQ +1.5 log unit. Maximum temperature of the particles was higher than 1400°C for approximately 0.5 seconds. Run products with rounded shape and smooth surface show the particles were completely melted. Chemical compositions of particles analyzed on cross sections are generally well homogenized from inhomogeneous starting materials by complete melting. Molar ratios of Fe in melted regions are close to 0.5, while compositions of S and O are various. Varieties of S and O compositions show various degree of oxidation and evaporation of sulfur. Distribution of compositions of melted regions in Fe-S-O system is plotted in liquidus compositions of FeO and FeS saturated melt. Troilite in micrometeorite is melted and oxidized by atmospheric entry. Compositions of FeS melt in fine spherules are following Fe-S-O phase relations even in a few seconds. Molar ratios of Fe in melt are close to 0.5, while compositions of S and O are various. Varieties of S and O compositions show various degree of oxidation and evaporation of sulfur. Evaporation of sulfur from meteoritic materials in atmospheric entry heating may depend on oxygen fugacity of the upper atmosphere. Sulfur supply from meteoritic materials to atmosphere may be limited on planets with oxygen-free atmosphere.

Dry sliding wear behavior of TIG welding clad WC composite coatings

NASA Astrophysics Data System (ADS)

Buytoz, Soner; Ulutan, Mustafa; Yildirim, M. Mustafa

2005-12-01

In this study, melted tungsten carbide powders on the surface of AISI 4340 steel was applied by using tungsten inert gas (TIG) method. It was observed that it has been solidified in different microstructures depending on the production parameters. As a result of microstructure examinations, in the surface modified layers an eutectic and dendrite solidification was observed together with WC, W 2C phases. In the layer produced, the hardness values varied between 950 and 1200 HV. The minimum mass loss was observed in the sample, which was treated in 1.209 mm/s production rate, 0.5 g/s powder feed rate and 13.9 kJ/cm heat input.

The Deep Crust Magmatic Refinery, Part 2 : The Magmatic Output of Numerical Models.

NASA Astrophysics Data System (ADS)

Bouilhol, P.; Riel, N., Jr.; Van Hunen, J.

2016-12-01

Metamorphic and magmatic processes occurring in the deep crust ultimately control the chemical and physical characteristic of the continental crust. A complex interplay between magma intrusion, crystallization, and reaction with the pre-existing crust provide a wide range of differentiated magma and cumulates (and / or restites) that will feed the upper crustal levels with evolved melt while constructing the lower crust. With growing evidence from field and experimental studies, it becomes clearer that crystallization and melting processes are non-exclusive but should be considered together. Incoming H2O bearing mantle melts will start to fractionate to a certain extent, forming cumulates but also releasing heat and H2O to the intruded host-rock allowing it to melt in saturated conditions. The end-result of such dynamic system is a function of the amount and composition of melt input, and extent of reaction with the host which is itself dependent on the migration mode of the melts. To better constrain lower crust processes, we have built up a numerical model [see Riel et al. associated abstract for methods] to explore different parameters, unravelling the complex interplay between melt percolation / crystallization and degassing / re-melting in a so called "hot zone" model. We simulated the intrusion of water bearing mantle melts at the base of an amphibolitized lower crust during a magmatic event that lasts 5 Ma. We varied several parameters such as Moho depth and melt rock ratio to better constrain what controls the final melt / lower crust composition.. We show the evolution of the chemical characteristics of the melt that escape the system during this magmatic event, as well as the resulting lower crust characteristics. We illustrate how the evolution of melt major elements composition reflects the progressive replacement of the crust towards compositions that are dominated by the mantle melt input. The resulting magmas cover a wide range of composition from tonalite to granite, and the modelled lower crust shows all the petrological characteristic of observed lower arc-crust.

An experimental investigation of agglutinate melting mechanisms - Shocked mixtures of sodium and potassium feldspars

NASA Technical Reports Server (NTRS)

Simon, S. B.; Papike, J. J.; Horz, F.; See, T. H.

1985-01-01

The results of an experiment designed to test the validity of the model for agglutinate formation involving fusion of the finest fraction or F3 are reported. Impact glasses were formed from various mixes of orthoclase and albite powders, which were used as analogs for soils with chemically constrasting coarse and fine fractions. The results showed that the single most important factor displacing the composition of a small-scale impact melt from the bulk composition of the source regolith is the fractionated composition of the finest soil fraction. Volatile loss and the amount of melting, which in turn are determined by the degree of shock, are also important. As predicted by the model, the lower pressure melts are the most fractionated, and higher pressure is accompanied by increased melting causing glass compositions to approach the bulk. In general, the systematics predicted by the model are observed; the model appears to be valid.

Heterozygote PCR product melting curve prediction.

PubMed

Dwight, Zachary L; Palais, Robert; Kent, Jana; Wittwer, Carl T

2014-03-01

Melting curve prediction of PCR products is limited to perfectly complementary strands. Multiple domains are calculated by recursive nearest neighbor thermodynamics. However, the melting curve of an amplicon containing a heterozygous single-nucleotide variant (SNV) after PCR is the composite of four duplexes: two matched homoduplexes and two mismatched heteroduplexes. To better predict the shape of composite heterozygote melting curves, 52 experimental curves were compared with brute force in silico predictions varying two parameters simultaneously: the relative contribution of heteroduplex products and an ionic scaling factor for mismatched tetrads. Heteroduplex products contributed 25.7 ± 6.7% to the composite melting curve, varying from 23%-28% for different SNV classes. The effect of ions on mismatch tetrads scaled to 76%-96% of normal (depending on SNV class) and averaged 88 ± 16.4%. Based on uMelt (www.dna.utah.edu/umelt/umelt.html) with an expanded nearest neighbor thermodynamic set that includes mismatched base pairs, uMelt HETS calculates helicity as a function of temperature for homoduplex and heteroduplex products, as well as the composite curve expected from heterozygotes. It is an interactive Web tool for efficient genotyping design, heterozygote melting curve prediction, and quality control of melting curve experiments. The application was developed in Actionscript and can be found online at http://www.dna.utah.edu/hets/. © 2013 WILEY PERIODICALS, INC.

P- T phase relations of silicic, alkaline, aluminous liquids: new results and applications to mantle melting and metasomatism

NASA Astrophysics Data System (ADS)

Draper, David S.; Green, Trevor H.

1999-07-01

We report new experimental results obtained under nominally anhydrous conditions at 1.0-1.5 GPa on a synthetic melt whose composition is typical of extreme-composition xenolith glasses. These results demonstrate that part of this extreme compositional range is in equilibrium with a lherzolitic assemblage (olivine, orthopyroxene, and clinopyroxene on the liquidus), extending our earlier findings [D.S. Draper, T.H. Green P- T phase relations of silicic, alkaline, aluminous mantle-xenolith glasses under anhydrous and C-O-H fluid-saturated conditions, J. Petrol. 38 (1997) 1187-1224] showing saturation with harzburgite minerals (olivine and orthopyroxene on the liquidus). The new results strengthen the view that such liquids can readily coexist with upper mantle rocks. Our results also bear on the current debate regarding the nature of low-degree mantle melts between proponents of the diamond-aggregate technique [who argue for comparatively silica- and alkali-rich low-degree melts; e.g., M.B. Baker, M.M. Hirschmann, M.S. Ghiorso, E.M. Stolper, Compositions of near-solidus peridotite melts from experiments and thermodynamic calculations, Nature 375 (1995) 308-311; M.B. Baker, M.M. Hirschmann, L.E. Wasylenki, E.M. Stolper, M.S. Ghiorso, Quest for low-degree mantle melts, Nature 381 (1996) 286] and those favoring the sandwich technique [who question the value of the diamond-aggregate work and argue that near-solidus melts must be nepheline- and olivine-normative; T.J. Falloon, D.H. Green, H.St.C. O'Neill, C.G. Ballhaus, Quest for low-degree mantle melts, Nature 381 (1996) 285; T.J. Falloon, D.H. Green, H.St.C. O'Neill, W.O. Hibberson, Experimental tests of low degree peridotite partial melt compositions: implications for the nature of anhydrous near-solidus peridotite melts at 1 GPa, Earth Planet. Sci. Lett. 152 (1997) 149-162]. Our results support aspects of both views. The sandwich-technique view is supported, for example, because all our liquids coexisting with mantle minerals are nepheline- and olivine-normative; and our olivine-liquid Fe-Mg exchange KD values fall on a trend similar to that supported by those workers. The diamond-aggregate view is supported, for example, because we find equilibrium between highly silicic, alkaline liquids and mantle minerals, showing the effect of high alkali contents to allow high silica contents at silica activities buffered by magnesian olivine and orthopyroxene at low pressure [M.M. Hirschmann, M.B. Baker, E.M. Stolper, The effect of alkalis on the silica content of mantle-derived melts, Geochim. Cosmochim. Acta 62 (1998) 883-902]. Additionally, the melting trends put forward by the sandwich-technique workers include revised low-degree melt compositions, as reported by Hirschmann et al., and our compositions fall on extensions of these trends. These new analyses also yield an olivine-liquid KD that more closely follows the trend of KD vs. melt alkali contents. The views of both sides of this controversy appear to permit, under certain conditions, the existence of small amounts of melt in the upper mantle with compositions similar to the extreme-composition xenolith glasses that are the focus of our work. On the basis of our new results, we conclude that extreme-composition xenolith glasses can act as agents of cryptic metasomatism in the upper mantle.

A Non-Arrhenian Viscosity Model for Natural Silicate Melts with Applications to Volcanology

NASA Astrophysics Data System (ADS)

Russell, J. K.; Giordano, D.; Dingwell, D. B.

2005-12-01

Silicate melt viscosity is the most important physical property in volcanic systems. It governs styles and rates of flow, velocity distributions in flowing magma, rates of vesiculation, and, ultimately, sets limits on coherent(vs. fragmented or disrupted) flow. The prediction of melt viscosity over the range of conditions found on terrestrial planets remains a challenge. However, the extraordinary increase in number and quality of published measurements of melt viscosity suggests the possibility of new models. Here we review the attributes of previous models for silicate melt viscosity and, then, present a new predictive model natural silicate melts. The importance of silicate melt viscosity was recognized early [1] and culminated in 2 models for predicting silicate melt viscosity [2,3]. These models used an Arrhenian T-dependence; they were limited by a limited experimental database dominated by high-T measurements. Subsequent models have aimed to: i) extend the compositional range of Arrhenian T-dependent models [4,5]; ii) to develop non-Arrhenian models for limited ranges of composition [6,7,8], iii) to develop new strategies for modelling the composition and T-dependence of viscosity [9,10,11], and, finally, to create chemical models for the non-Arrhenian T-dependence of natural melts [12]. We present a multicomponent model for the compositional and T dependence of silicate melt viscosity based on data spanning a wide range of anhydrous melt compositions. The experimental data include micropenetration and concentric cylinder viscometry measurements covering a viscosity range of 10-1 to 1012 Pa s and a T-range from 700 to 1650°C. These published data provide a high- quality database comprising ~ 800 experimental data on 44 well-characterized melt compositions. Our model uses the Adam-Gibbs equation to capture T-dependence: log η = A + B/[T · log (T/C)] where A, B, and C are adjustable parameters that vary for different melt compositions. We assume that all silicate melts converge to a common, but unknown, high-T limit (e.g., A) and that all compositional dependence is accommodated for by B and C. We adopt a linear compositional dependence for B and C: B = σi=1..n [xi βi] C = σi=1..n [xi γi] where xi's are the mole fractions of oxide components (n=8) and βi and γi are adjustable parameters. The model, therefore, comprises 2 · n+1 adjustable parameters which are optimized for against the experimental database including a common value of A and compositional coefficeints for B and C. The new model reproduces the original database to within experimental uncertainty and can predict the viscosity of silicate melts across the full range of conditions found in Nature. References Cited: [1] Friedman et al., 1963. J Geophys Res 68, 6523-6535. [2] Bottinga Y & Weill D 1972. Am J Sci 272, 438- 475. [3] Shaw HR 1972. Am J Sci 272, 438- 475. [4] Persikov ES 1991. Adv Phys Geochem 9, 1-40. [5] Prusevich AA 1988. Geol Geofiz 29, 67-69. [6] Baker DR 1996. Am Min 81, 126-134. [7] Hess KU & Dingwell DB 1996. Am Min 81, 1297- 1300. [8] Zhang, et al. 2003. Am min 88, 1741- 1752. [9] Russell et al. 2002. Eur J Min 14, 417-428. [10] Russell et al. 2003. Am Min 8, 1390- 1394. [11] Russell JK & Giordano D In Press. Geochim Cosmochim Acta. [12] Giordano D & Dingwell DB 2003. Earth Planet. Sci. Lett. 208, 337-349.

Evidence for the presence of carbonate melt during the formation of cumulates in the Colli Albani Volcanic District, Italy

NASA Astrophysics Data System (ADS)

Shaw, Cliff S. J.

2018-06-01

Fergusite and syenite xenoliths and mafic lapilli from two locations in the Villa Senni ignimbrite of the Colli Albani Volcanic District show evidence for fractionation of a silicate magma that led to exsolution of an immiscible carbonate melt. The fergusite xenoliths are divided into two groups on the basis of their clinopyroxene compositions. Group 1 clinopyroxene records the crystallisation of a silicate melt and enrichment of the melt in Al, Ti and Mn and depletion in Si as well as enrichment in incompatible trace elements. The second group of clinopyroxene compositions (group 2) comes mainly from Ba-F-phlogopite- and Ti-andradite-bearing fergusites. They have significantly higher Si and lower Al and Ti and, like the coexisting phlogopite and garnet are strongly enriched in Mn. The minerals in the fergusites containing group 2 clinopyroxene are enriched in Ba, Sr, Cs, V and Li all of which are expected to partition strongly into a carbonate melt phase relative to the coexisting silicate melt. The compositional data suggest that the group 1 fergusites record sidewall crystallisation of CO2-rich silicate melt and that once the melt reached a critical degree of fractionation, carbonate melt exsolved. The group 2 fergusites record continued crystallisation in this heterogeneous silicate - carbonate melt system. Composite xenoliths of fergusite and thermometamorphic skarn record contact times of hundreds to a few thousand years indicating that fractionation and assimilation was relatively rapid.

Mantle Evolution Beneath The Colorado Palteau: Interpreta-tion of The Study of Mineral Concentrate From Kimberlite Pipe Kl-1 Colorado.

NASA Astrophysics Data System (ADS)

Ashchepkov, I.; Vladykin, N.; Mitchell, R.; Coopersmith, H.; Garanin, V.; Saprykin, A. I.; Khmelnikova, O. S.

Mineral grains and their intergrowth from the concentrate form the KL1- kimberlite pipe Colorado plateau was analyzed by EPMA and LAM ICP MS in Analytic Center of UIGGM. Garnets reveal nearly continuous trend of the compositions divided into 5 intervals. 1 cumulates from the crust and Sp facie mantle; 2. Gar-Sp lherzolites; 3- Gar- wehrlites, lherzolites and harzburgites; 4- Gar lherzolites and harzburgites; 4. Pyroxenites and Il peri-dotites . They reveal three trend of Ti decrease with the ris- ing Cr content. Those in the inter-growth with the pyroxenes are less in Tio2 as well as the pyroxenes. Discrete large Cpx grains are richer in Na, Al, Cr. TP conditions determined for the clinopyroxenes with Nimis- Taylor, 2001 thermobarometer and barometer Ashchepkov, 2001 reveal the heating from 35 to 40-42 mv/m2 in 30-50kbar interval. The spinels show two compositional intervals 64-50% Cr2O3 and 47-30%. The branch with the essential enrichment to 8% TiO2with the Cr decrease what also suppose the peridotite alteration due to rising of evolving Ti-rich melts. Two descend- ing crystallization lines for the ilmenites suggest the (polybaric) differentiation in two magmatic chambers. The Cr-rich ilmenites and most Cr-rich subcalcis garnets were found in the serpentinized ilmenite harzburgites that probably surround the most deep mag-matic chamber. The Ilm -Q (coesite) intergrowth suggests the deep differenti- ation. Several ilmenites contain up to 11%MnO. Trace elements determined for the clinopyroxenes suppose small decree melting possibly under influence of subducted- related melts having definite U peak and Ta-Nb minimums. Their reaction with peri- dotites with garnet dissolution according to AFC model decrease La/Ybn ration as well as the Pb* and U peak. Two stages of the Ti-rich melt percolations suggested to be accompanied the plum- re-lated melts influence on the peridotite of Wyoming craton keel which was followed with fur-ther followed by submelting of the subducted essentially eclogitic Na-Ti material. The de-formations assist the melt percolation at the final stage. Supported by RBEF grants 05-99-65688, 00-05-65288

Method of producing particulate-reinforced composites and composties produced thereby

DOEpatents

Han, Qingyou; Liu, Zhiwei

2013-12-24

A process for producing particle-reinforced composite materials through utilization of an in situ reaction to produce a uniform dispersion of a fine particulate reinforcement phase. The process includes forming a melt of a first material, and then introducing particles of a second material into the melt and subjecting the melt to high-intenisty acoustic vibration. A chemical reaction initiates between the first and second materials to produce reaction products in the melt. The reaciton products comprise a solide particulate phase, and the high-intensity acoustic vibration fragments and/or separates the reaction products into solid particles that are dispersed in the melt and are smaller than the particles of the second material. Also encompassed are particles-reinforced composite materials produced by such a process.

Toward Assessing the Causes of Volcanic Diversity in the Cascades Arc

NASA Astrophysics Data System (ADS)

Till, C. B.; Kent, A. J.; Abers, G. A.; Pitcher, B.; Janiszewski, H. A.; Schmandt, B.

2017-12-01

A fundamental unanswered question in subduction system science is the cause of the observed diversity in volcanic arc style at an arc-segment to whole-arc scale. Specifically, we have yet to distinguish the predominant mantle and crustal processes responsible for the diversity of arc volcanic phenomenon, including the presence of central volcanoes vs. dispersed volcanism; episodicity in volcanic fluxes in time and space; variations in magma chemistry; and differences in the extent of magmatic focusing. Here we present a thought experiment using currently available data to estimate the relative role of crustal magmatic processes in producing the observed variations in Cascades arc volcanism. A compilation of available major element compositions of Quaternary arc volcanism and estimates of eruptive volumes are used to examine variations in the composition of arc magmas along strike. We then calculate the Quaternary volcanic heat flux into the crust, assuming steady state, required to produce the observed distribution of compositions via crystallization of mantle-derived primitive magmas vs. crustal melting using experiment constraints on possible liquid lines of descent and crustal melting scenarios. For pure crystallization, heat input into the crust scales with silica content, with dacitic to rhyolite compositions producing significantly greater latent heat relative to basalts to andesites. In contrast, the heat required to melt lower crustal amphibolite decreases with increasing silica and is likely provided by the latent heat of crystallization. Thus we develop maximum and minimum estimates for heat added to the crust at a given SiO2 range. When volumes are considered, we find that the average Quaternary volcanic heat flux at latitudes south of South Sister to be more than twice that to the north. Distributed mafic volcanism produces only a quarter to half the heat flux calculated for the main edifices at a given latitude because of their lesser eruptive volumes and quantities of evolved magma. When we compare our Quaternary heat flux calculations to a variety of geophysical observations, we find that regions of calculated higher volcanic heat flux coincide with regions of significantly lower crustal seismic wave speeds beneath and behind the arc, as well as with regions of significantly higher heat flow.

21 CFR 178.3130 - Antistatic and/or anti-fogging agents in food-packaging materials.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-hydroxyethyl)dodecanamide produced when diethanolamine is made to react with methyl laurate such that the... with methyl laurate such that the finished product: Has a minimum melting point of 36 °C; has a minimum...

Constraints on lithosphere-asthenosphere melt mixing in basaltic intraplate volcanism from olivine melt inclusions from southern Payenia, Argentina

NASA Astrophysics Data System (ADS)

Søager, Nina; Portnyagin, Maxim; Hoernle, Kaj; Holm, Paul Martin; Garbe-Schönberg, Dieter

2018-06-01

We present major and trace element compositions of melt inclusions from three alkali basalts from the Río Colorado volcanic field in the Payenia backarc province, Argentina. Modeling of diffusion profiles around the inclusions showed that most inclusions equilibrated <14 days after formation, indicating a short crustal residence time for the magmas and nearly direct ascent through the crust. Despite overlapping host rock isotopic compositions, the inclusions show a large variation in their degree of enrichment, and display trends that we interpret as mixing between asthenospheric OIB-type low K2O-high Nb/U melts and enriched high K2O-low Nb/U lithospheric mantle melts similar in composition to alkaline lamprophyres. The low Nb/U magmas are excessively enriched in the elements Cs, Rb, Ba, Th, U, K, Pb and Cl relative to Nb, Ta and REEs. The enriched low Nb/U components are interpreted to have formed by percolative fractional crystallization of asthenospheric high Nb/U melts in the lithospheric mantle involving crystallization of clinopyroxene, apatite and rutile. The residual fluid-rich melts either mixed directly with new batches of high Nb/U melts or metasomatized and veined the lithospheric mantle which later re-melted during continued volcanism. The major element compositions of the high K2O-low Nb/U components are distinct for the whole rocks and melt inclusions, and most enriched inclusions have lower SiO2 and higher TiO2 contents indicating derivation by melting of amphibole-bearing veins. In contrast, most whole rock low Nb/U basalts have higher SiO2 and lower TiO2 and were most likely formed by melting of pyroxenitic veins or peridotitic metasomatized lithospheric mantle.

Phase relations in the Fe-FeSi system at high pressures and temperatures

NASA Astrophysics Data System (ADS)

Fischer, Rebecca A.; Campbell, Andrew J.; Reaman, Daniel M.; Miller, Noah A.; Heinz, Dion L.; Dera, Przymyslaw; Prakapenka, Vitali B.

2013-07-01

The Earth's core is comprised mostly of iron and nickel, but it also contains several weight percent of one or more unknown light elements, which may include silicon. Therefore it is important to understand the high pressure, high temperature properties and behavior of alloys in the Fe-FeSi system, such as their phase diagrams. We determined melting temperatures and subsolidus phase relations of Fe-9 wt% Si and stoichiometric FeSi using synchrotron X-ray diffraction at high pressures and temperatures, up to ~200 GPa and ~145 GPa, respectively. Combining this data with that of previous studies, we generated phase diagrams in pressure-temperature, temperature-composition, and pressure-composition space. We find the B2 crystal structure in Fe-9Si where previous studies reported the less ordered bcc structure, and a shallower slope for the hcp+B2 to fcc+B2 boundary than previously reported. In stoichiometric FeSi, we report a wide B2+B20 two-phase field, with complete conversion to the B2 structure at ~42 GPa. The minimum temperature of an Fe-Si outer core is 4380 K, based on the eutectic melting point of Fe-9Si, and silicon is shown to be less efficient at depressing the melting point of iron at core conditions than oxygen or sulfur. At the highest pressures reached, only the hcp and B2 structures are seen in the Fe-FeSi system. We predict that alloys containing more than ~4-8 wt% silicon will convert to an hcp+B2 mixture and later to the hcp structure with increasing pressure, and that an iron-silicon alloy in the Earth's inner core would most likely be a mixture of hcp and B2 phases.

Phase relations in the Fe-FeSi system at high pressures and temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, Rebecca A.; Campbell, Andrew J.; Reaman, Daniel M.

2016-07-29

The Earth's core is comprised mostly of iron and nickel, but it also contains several weight percent of one or more unknown light elements, which may include silicon. Therefore it is important to understand the high pressure, high temperature properties and behavior of alloys in the Fe–FeSi system, such as their phase diagrams. We determined melting temperatures and subsolidus phase relations of Fe–9 wt% Si and stoichiometric FeSi using synchrotron X-ray diffraction at high pressures and temperatures, up to ~200 GPa and ~145 GPa, respectively. Combining this data with that of previous studies, we generated phase diagrams in pressure–temperature, temperature–composition,more » and pressure–composition space. We find the B2 crystal structure in Fe–9Si where previous studies reported the less ordered bcc structure, and a shallower slope for the hcp+B2 to fcc+B2 boundary than previously reported. In stoichiometric FeSi, we report a wide B2+B20 two-phase field, with complete conversion to the B2 structure at ~42 GPa. The minimum temperature of an Fe–Si outer core is 4380 K, based on the eutectic melting point of Fe–9Si, and silicon is shown to be less efficient at depressing the melting point of iron at core conditions than oxygen or sulfur. At the highest pressures reached, only the hcp and B2 structures are seen in the Fe–FeSi system. We predict that alloys containing more than ~4–8 wt% silicon will convert to an hcp+B2 mixture and later to the hcp structure with increasing pressure, and that an iron–silicon alloy in the Earth's inner core would most likely be a mixture of hcp and B2 phases.« less

Plastic phase change material and articles made therefrom

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abhari, Ramin

The present invention generally relates to a method for manufacturing phase change material (PCM) pellets. The method includes providing a melt composition, including paraffin and a polymer. The paraffin has a melt point of between about 10.degree. C. and about 50.degree. C., and more preferably between about 18.degree. C. and about 28.degree. C. In one embodiment, the melt composition includes various additives, such as a flame retardant. The method further includes forming the melt composition into PCM pellets. The method further may include the step of cooling the melt to increase the melt viscosity before pelletizing. Further, PCM compounds aremore » provided having an organic PCM and a polymer. Methods are provided to convert the PCM compounds into various form-stable PCMs. A method of coating the PCMs is included to provide PCMs with substantially no paraffin seepage and with ignition resistance properties.« less

Petrology of Impact-Melt Rocks at the Chicxulub Multiring Basin, Yucatan, Mexico

NASA Technical Reports Server (NTRS)

Schuraytz, Benjamin C.; Sharpton, Virgil L.; Marin, Luis E.

1994-01-01

Compositions and textures of melt rocks from the upper part of the Chicxulub structure are typical of melt rocks at other large terrestrial impact structures. Apart from variably elevated iridium concentrations (less than 1.5 to 13.5 +/- 0.9 ppb) indicating nonuniform dissemination of a meteoritic component, bulk rock and phenocryst compositions imply that these melt rocks were derived exclusively from continental crust and platform-sediment target lithologies. Modest differences in bulk chemistry among samples from wells located approximately 40 km apart suggest minor variations in relative contributions of these target lithologies to the melts. Subtle variations in the compositions of early-formed pyroxene and plagioclase also support minor primary differences in chemistry between the melts. Evidence for pervasive hydrothermal alteration of the porous mesostasis includes albite, K-feldspar, quartz, epidote, chlorite, and other phyllosilicates, as well as siderophile element-enriched sulfides, suggesting the possibility that Chicxulub, like Sudbury, may host important ore deposits.

Effect of strain rate on mechanical properties of melt-processed soy flour composite filler and styrene-butadiene blends

USDA-ARS?s Scientific Manuscript database

Polymer composites were prepared by melt-mixing polymer and soy flour composite fillers in an internal mixer. Soy flour composite fillers were prepared by blending aqueous dispersion of soy flour with styrene-butadiene rubber latex, dried, and cryogenically ground into powders. Upon crosslinking, th...

CO2 Solubility in Rhyolitic Melts as a Function of P, T, and fO2 - Implications for Carbon Flux in Subduction Zones

NASA Astrophysics Data System (ADS)

Duncan, M. S.; Dasgupta, R.

2013-12-01

Understanding the balance between subduction inputs vs. arc output of carbon is critical for constraining the global carbon cycle. However, the agent of carbon transfer from slab to sub-arc mantle is not constrained [1]. Partial melt of ocean-floor sediments is thought to be a key agent of mass transfer in subduction zones, accounting for the trace element characteristics of arc magmas [2]. Yet the carbon carrying capacity of rhyolitic partial melts of sediments remains unknown at sub-arc depths. In our previous work [3], we constrained CO2 solubility of natural rhyolite from 1.5-3.0 GPa, 1300 °C and logfO2 at FMQ×1.0. However, the effects of T and fO2 on CO2 solubility remain unconstrained. In particular, for sediments with organic carbon, graphite stability is expected and the fO2 of C-dissolution can be lower, which may affect the solubility. Thus it is critical to constrain the CO2 solubility of sediment partial melts under graphite-saturated conditions. We determined CO2 solubility of a model rhyolite composition, similar to partial melt composition of natural metapelite [4], at graphite saturation, using Pt/Gr capsules and a piston cylinder device. Experiments were conducted at 1.5-3.0 GPa and 1100-1400 °C. FTIR was employed to measure the concentrations of CO2 and H2O in doubly polished experimental glasses. Raman and SIMS were used to determine the presence of reduced carbon species and total carbon, respectively. FTIR spectra reveal that CO2 is dissolved as both molecular CO2 (CO2mol.) and carbonates (CO32-). For graphite-saturated, hydrous melts with measured H2O ~2.0 wt.%, CO2tot. (CO2mol.+CO32-) values increase with increasing P from ~0.6 to 1.2 wt.% from 1.5 to 3.0 GPa at 1300 °C. These values are lower than more oxidized melts with the same water content, which were 0.85 to 1.99 wt.% CO2 as P increased. At 3 GPa, graphite-saturated experiments from 1100 to 1300 °C yield CO2tot. value of 1.18-1.20 wt.%, suggesting minor effect of temperature in bulk CO2 solubility. To meet the minimum requirement of 3000 ppm CO2 in primary arc magma [5,6], the required sediment melt contribution is 0.18-0.28 wt.% CO2, which is distinctly lower than the solubility limit of graphite-saturated melt. However, 1.7 wt.% CO2 in primary arc basalts [5] exceeds the solubility limit of reduced, hydrous melts, which is in contrast to more oxidized, hydrous melts which can contribute up to 2 wt.% CO2. We determine that ~1.7-15% of sediment melt would be required to meet 3000 ppm CO2 in the primary arc basalt depending on the depth of melting (1.5-3.0 GPa) and the degree of mantle wedge melting (15-30%). This contribution is higher than that previously calculated for the more oxidized melts, but still may not be an unreasonable slab flux. [1] Dasgupta (2013) RiMG, 75, 183-229; [2] Plank and Langmuir (1993) Nature, 362, 739-743. [3] Duncan and Dasgupta. (in review) GCA; [4] Tsuno and Dasgupta (2011) CMP, 161, 743-763; [5] Blundy et al. (2010) EPSL, 290, 289-301; [6] Wallace (2005) JVGR, 140, 217-240.

PROCESS FOR SEPARATING URANIUM FISSION PRODUCTS

DOEpatents

Spedding, F.H.; Butler, T.A.; Johns, I.B.

1959-03-10

The removal of fission products such as strontium, barium, cesium, rubidium, or iodine from neutronirradiated uranium is described. Uranium halide or elemental halogen is added to melted irradiated uranium to convert the fission products to either more volatile compositions which vaporize from the melt or to higher melting point compositions which separate as solids.

Tin in granitic melts: The role of melting temperature and protolith composition

NASA Astrophysics Data System (ADS)

Wolf, Mathias; Romer, Rolf L.; Franz, Leander; López-Moro, Francisco Javier

2018-06-01

Granite bound tin mineralization typically is seen as the result of extreme magmatic fractionation and late exsolution of magmatic fluids. Mineralization, however, also could be obtained at considerably less fractionation if initial melts already had enhanced Sn contents. We present chemical data and results from phase diagram modeling that illustrate the dominant roles of protolith composition, melting conditions, and melt extraction/evolution for the distribution of Sn between melt and restite and, thus, the Sn content of melts. We compare the element partitioning between leucosome and restite of low-temperature and high-temperature migmatites. During low-temperature melting, trace elements partition preferentially into the restite with the possible exception of Sr, Cd, Bi, and Pb, that may be enriched in the melt. In high-temperature melts, Ga, Y, Cd, Sn, REE, Pb, Bi, and U partition preferentially into the melt whereas Sc, V, Cr, Co, Ni, Mo, and Ba stay in the restite. This contrasting behavior is attributed to the stability of trace element sequestering minerals during melt generation. In particular muscovite, biotite, titanite, and rutile act as host phases for Sn and, therefore prevent Sn enrichment in the melt as long as they are stable phases in the restite. As protolith composition controls both the mineral assemblage and modal contents of the various minerals, protolith composition eventually also controls the fertility of a rock during anatexis, restite mineralogy, and partitioning behavior of trace metals. If a particular trace element is sequestered in a phase that is stable during partial melting, the resulting melt is depleted in this element whereas the restite becomes enriched. Melt generation at high temperature may release Sn when Sn-hosts become unstable. If melt has not been lost before the breakdown of Sn-hosts, Sn contents in the melt will increase but never will be high. In contrast, if melt has been lost before the decomposition of Sn-hosts, the small volume of the high-temperature melt will not be diluted by low-temperature, low-Sn melts and, therefore, could have high Sn-contents. The combination of multiple melt extractions and Sn-mobilization at high temperature results in strong Sn enrichment in late, high-temperature melts. Metal enrichment during partial melting becomes particularly efficient, if the sedimentary protolith had experienced intense chemical alteration as the loss of Na and Ca together with a relative enrichment of K favors muscovite-rich metamorphic mineral assemblages that produce large amounts of melt during muscovite dehydration melting.

Formation of Apollo 16 impactites and the composition of late accreted material: Constraints from Os isotopes, highly siderophile elements and sulfur abundances

NASA Astrophysics Data System (ADS)

Gleißner, Philipp; Becker, Harry

2017-03-01

Fe-Ni metal-schreibersite-troilite intergrowths in Apollo 16 impact melt rocks and new highly siderophile element (HSE) and S abundance data indicate that millimeter-scale closed-system fractional crystallization processes during cooling of impactor-derived metal melt droplets in impact-melts are the main reason for compositional variations and strong differences in abundances and ratios of HSE in multiple aliquots from Apollo 16 impact melt rocks. Element ratios obtained from linear regression of such data are therefore prone to error, but weighted averages take into account full element budgets in the samples and thus represent a more accurate estimate of their impactor contributions. Modeling of solid metal-liquid metal partitioning in the Fe-Ni-S-P system and HSE patterns in impactites from different landing sites suggest that bulk compositions of ancient lunar impactites should be representative of impact melt compositions and that large-scale fractionation of the HSE by in situ segregation of solid metal or sulfide liquid in impact melt sheets most likely did not occur. The compositional record of lunar impactites indicates accretion of variable amounts of chondritic and non-chondritic impactor material and the mixing of these components during remelting of earlier ejecta deposits. The non-chondritic composition appears most prominently in some Apollo 16 impactites and is characterized by suprachondritic HSE/Ir ratios which increase from refractory to moderately volatile HSE and exhibit a characteristic enrichment of Ru relative to Pt. Large-scale fractional crystallization of solid metal from sulfur and phosphorous rich metallic melt with high P/S in planetesimal or embryo cores is currently the most likely process that may have produced these compositions. Similar materials or processes may have contributed to the HSE signature of the bulk silicate Earth (BSE).

Coupled petrological-geodynamical modeling of a compositionally heterogeneous mantle plume

NASA Astrophysics Data System (ADS)

Rummel, Lisa; Kaus, Boris J. P.; White, Richard W.; Mertz, Dieter F.; Yang, Jianfeng; Baumann, Tobias S.

2018-01-01

Self-consistent geodynamic modeling that includes melting is challenging as the chemistry of the source rocks continuously changes as a result of melt extraction. Here, we describe a new method to study the interaction between physical and chemical processes in an uprising heterogeneous mantle plume by combining a geodynamic code with a thermodynamic modeling approach for magma generation and evolution. We pre-computed hundreds of phase diagrams, each of them for a different chemical system. After melt is extracted, the phase diagram with the closest bulk rock chemistry to the depleted source rock is updated locally. The petrological evolution of rocks is tracked via evolving chemical compositions of source rocks and extracted melts using twelve oxide compositional parameters. As a result, a wide variety of newly generated magmatic rocks can in principle be produced from mantle rocks with different degrees of depletion. The results show that a variable geothermal gradient, the amount of extracted melt and plume excess temperature affect the magma production and chemistry by influencing decompression melting and the depletion of rocks. Decompression melting is facilitated by a shallower lithosphere-asthenosphere boundary and an increase in the amount of extracted magma is induced by a lower critical melt fraction for melt extraction and/or higher plume temperatures. Increasing critical melt fractions activates the extraction of melts triggered by decompression at a later stage and slows down the depletion process from the metasomatized mantle. Melt compositional trends are used to determine melting related processes by focusing on K2O/Na2O ratio as indicator for the rock type that has been molten. Thus, a step-like-profile in K2O/Na2O might be explained by a transition between melting metasomatized and pyrolitic mantle components reproducible through numerical modeling of a heterogeneous asthenospheric mantle source. A potential application of the developed method is shown for the West Eifel volcanic field.

The influence of melt composition on the partitioning of REEs, Y, Sc, Zr and Al between forsterite and melt in the system CMAS

NASA Astrophysics Data System (ADS)

Evans, Thomas M.; O'Neill, Hugh St. C.; Tuff, James

2008-12-01

Partition coefficients for a range of Rare Earth Elements (REEs), Y, Sc, Al and Zr were determined between forsteritic olivine (nearly end-member Mg 2SiO 4) and ten melt compositions in the system CaO-MgO-Al 2O 3-SiO 2 (CMAS) at 1 bar and 1400 °C, with concentrations of the trace elements in the olivine and the melt measured by laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The REEs and Sc were added at levels sufficient to ensure that concentrations in the olivine were well above the detection limits. The REE partition coefficients (DREEol/melt) decrease with increasing silica in the melt, indicating strong bonding between REEO 1.5 and SiO 2 in the melt. The variation of DREEol/melt as a function of ionic radius is well described by the Brice equation for each composition, although a small proportion of this variation is due to the increase in the strength of the REEO 1.5-SiO 2 interactions in the melt with ionic radius. Scandium behaves very similarly to the REEs, but a global fit of the data from all ten melt compositions suggests that DScol/melt deviates somewhat from the parabolas established by the REE and Y, implying that Sc may substitute into olivine differently to that of the REEs. In contrast to the behaviour of the large trivalent cations, the concentration of Al in olivine is proportional to the square root of its concentration in the melt, indicating a coupled substitution in olivine with a high degree of short-range order. The lack of any correlation of REE partition coefficients with Al in olivine or melt suggests that the REE substitution in olivine is charge-balanced by cation vacancies. The partition coefficient of the tetravalent trace element Zr, which is highly incompatible in olivine, depends on the CaO content of the melt.

Dependence of Ru2O3 Activity on Composition of Silicate Melts: Using Statistical Correlations to Infer Thermodynamic Behavior in the Melt

NASA Technical Reports Server (NTRS)

Colson, R. O.; Malum, K. M.

2005-01-01

Understanding variations in activity with composition is an essential step in improving prediction of partition coefficients during magma evolution. Variations in activity with composition are complex and do not generally exhibit ideal behavior relative to a traditional melt-component set. Although deviations from component ideality can be modeled numerically by simply fitting to compositional variables (such as in a regular or subregular solution model), such models have not been particularly successful for describing variations in trace component activities. A better approach might be to try to identify components that do a better job of describing the behavior of the species in the melt. Electrochemical Measurement of Ru2O3 activities: Electrodes were inserted into silicate melt beads of various compositions (Table 1) suspended on Ptwire loops in a 1-atm gas mixing furnace. An electrical potential was imposed between the electrodes, the imposed potential increasing along a step ramp with a pulse imposed on each step (Fig. 1). Current flows between electrodes when electroactive species in the melt are oxidized or reduced at the electrodes. The resulting current was measured at the top and bottom of the voltage pulse, and the difference (the differential current) was plotted against potential. The peak of the resulting curve is related to the activity coefficient for the particular electroactive species (Ru2O3) in the melt [1, 2, 3]. A significant part of the nonideal contribution to activity is due not to intrinsic properties of the component in the melt, but to our ignorance about the state and mixing properties of the component in the melt.

Olivine-hosted melt inclusions record efficient mixing of mantle melts in continental flood basalt provinces

NASA Astrophysics Data System (ADS)

Jennings, E. S.; Gibson, S. A.; Maclennan, J.; Heinonen, J. S.

2017-12-01

Primitive melt inclusions trapped in various minerals found in global ridge settings have been shown to record highly variable magmatic compositions. Mantle melting is expected to be near-fractional, producing a wide range of melt compositions that must accumulate and mix in crustal magma chambers. In primitive rocks, the melt inclusion variability observed in major, trace and isotope geochemistry is consistent to the first order with partial melting of variably depleted mantle, and indicate that the host phases began to crystallise prior to the completion of melt aggregation and mixing. We present new major and trace element data from a large number of rehomogenised olivine-hosted melt inclusions from the Cretaceous Paraná-Etendeka and Jurassic Karoo continental flood basalt (CFB) provinces [1]. We show that the major element chemistry of the melt inclusions can be severely disrupted by the rehomogenisation process and, as a consequence, their initial compositions cannot easily be back-calculated. However, despite the age of the samples, the trace element geochemistry of the melt inclusions is well-preserved. Despite coming from near-liquidus olivines from primitive picrites and ferropicrites, the inclusions are remarkably homogeneous; none of the anticipated variability in incompatible trace element compositions is observed. When considered alongside literature data, it appears that variability in primitive melts - as recorded by melt inclusions - is low in CFBs and OIBs relative to ridge settings, e.g. Iceland. We suggest that the tectonic setting imposes a control on the mixing of mantle melts: hot, plume-derived melts generated beneath relatively thick lithosphere may be prone to efficient mixing, perhaps due to their low viscosity, long transport pathways, and/or a superliquidus emplacement temperature [1]. This interpretation is supported by the almost non-existent variability of olivine-hosted inclusions from ferropicrite samples: these magmas represents the deepest, hottest and lowest viscosity magma of all the samples considered. [1] Jennings E. S., Gibson S. A., Maclennan J. and Heinonen J. S. (2017) Deep mixing of mantle melts beneath continental flood basalt provinces: Constraints from olivine-hosted melt inclusions in primitive magmas. Geochimica et Cosmochimica Acta 196, 36-57.

Pyroxene-melt equilibria. [for lunar maria basalts

NASA Technical Reports Server (NTRS)

Nielsen, R. L.; Drake, M. J.

1979-01-01

A thermodynamic analysis of pyroxene-melt equilibria is performed through use of a literature survey of analyses of high-Ca pyroxene and coexisting silicate melt pairs and analyses of low-Ca pyroxene silicate melt pairs. Reference is made to a modified version of a model developed by Bottinga and Weill (1972) which more successfully accounts for variations in melt composition than does a model which considers the melt to be composed of simple oxides which mix ideally. By using a variety of pyroxene melt relations, several pyroxene-melt and low-Ca pyroxene-high-Ca pyroxene geothermometers are developed which have internally consistant precisions of approximately + or - 20 C. Finally, it is noted that these equations may have application in modeling the evolution of mineral compositions during differentiation of basaltic magmas.

Composition of Impact Melt Debris from the Eltanin Impact Strewn Field, Bellingshausen Sea

NASA Technical Reports Server (NTRS)

Kyte, Frank T.

2002-01-01

The impact of the km-sized Eltanin asteroid into the Bellingshausen Sea produced mm- to cm-sized vesicular impact melt-rock particles found in sediment cores across a large area of the ocean floor. These particles are composed mainly of olivine and glass with minor chromite and traces of NiFe-sulfides. Some particles have inclusions of unmelted mineral and rock fragments from the precursor asteroid. Although all samples of melt rock examined have experienced significant alteration since their deposition in the late Pliocene, a significant portion of these particles have interiors that remain pristine and can be used to estimate the bulk composition of the impact melt. The bulk composition of the melt-rock particles is similar to the composition of basaltic meteorites such as howardites or mesosiderite silicates, with a contribution from seawater salts and a siderophile-rich component. There is no evidence that the Eltanin impact melt contains a significant terrestrial silicate component that might have been incorporated by mixing of the projectile with oceanic crust. If terrestrial silicates were incorporated into the melt, then their contribution must be much less than 10 wt%. Since excess K, Na, and CI are not present in seawater proportions, uptake of these elements into the melt must have been greatest for K and least for CI, producing a K/CI ratio about 4 times that in seawater. After correcting for the seawater component, the bulk composition of the Eltanin impact melt provides the best estimate of the bulk composition of the Eltanin asteroid. Excess Fe in the impact melt, relative to that in howardites, must be from a significant metal phase in the parent asteroid. Although the estimated Fe:Ni:Ir ratios (8:1:4 x 10(exp -5)) are similar to those in mesosiderite metal nodules (10:1:6 x 10(exp -5), excess Co and Au by factors of about 2 and 10 times, respectively, imply a metal component distinct from that in typical mesosiderites. An alternative interpretation, that siderophiles have been highly fractionated from a mesosiderite source, would require loss of about 90% of the original metal from the impact melt and the sediments, and is unsupported by any observational data. More likely, the excess Fe in the melt rocks is 'representative of the amount of metal in the impacting asteroid, which is estimated to be 4+/- 1 wt%.

A new approach to reconstructing the composition and evolution of kimberlite melts: A case study of the archetypal Bultfontein kimberlite (Kimberley, South Africa)

NASA Astrophysics Data System (ADS)

Soltys, Ashton; Giuliani, Andrea; Phillips, David

2018-04-01

The compositions of kimberlite melts at depth and upon emplacement in the upper crust remain elusive. This can be attributed to the unquantified effects of multiple processes, such as alteration, assimilation, xenocryst contamination, and fractional crystallisation. The inability to accurately constrain the composition and physical properties of kimberlite melts prevents a comprehensive understanding of their petrogenesis. To improve constraints on the compositions of kimberlite melts, we have combined modal analysis including the discrimination of xenocrystic from magmatic phases, with mineral chemistry determinations to reconstruct a whole-rock composition. We apply this approach to a sample of "fresh" macrocrystic hypabyssal kimberlite (sample BK-1) from the Bultfontein mine (Kimberley, South Africa). The accuracy of this whole-rock reconstruction method is validated by the similarity between reconstructed and measured whole-rock compositions. A series of corrections are then applied to account for the effects of post-emplacement serpentinisation, pre-emplacement olivine crystallisation, and the inclusion and assimilation of mantle material. This approach permits discernment of melt compositions at different stages of kimberlite evolution. The primitive melt parental to the Bultfontein kimberlite is estimated to contain 17.4-19.0 wt% SiO2, 20.2-22.8 wt% MgO, 20.9-21.9 wt% CaO, 2.1-2.3 wt% P2O5, 1.2-1.4 wt% TiO2, 0.9-1.1 wt% Al2O3, and 0.6-0.7 wt% K2O, and has a Mg# of 83.4-84.4. Primary volatile contents (i.e., after an attempt to account for volatile loss) are tentatively estimated at 2.1-2.2 wt% H2O and 22.9-25.4 wt% CO2. This composition is deficient in SiO2, MgO and H2O, but enriched in CaO and CO2 compared with most previous estimates of primitive kimberlite melts. We suggest that the primitive melt parental to the Bultfontein kimberlite was a transitional silicate-carbonate melt, which was progressively enriched in SiO2, MgO, Al2O3, Cr2O3, and Na2O through the assimilation of lithospheric mantle material. Comparisons with experimentally produced low-degree melts of carbonated lherzolite indicate that the Bultfontein kimberlite could have formed by 0.5% melting of asthenospheric mantle at 6.0-8.6 GPa (i.e., 190-285 km) and 1400-1500 °C. The low calculated Na2O contents (<0.2 wt%), which are inconsistent with derivation from low-degree melting of lherzolite, suggest that an alkali-bearing, volatile-rich fluid was exsolved during ascent or released after emplacement, and subsequently removed.

Hydrous melt-rock reaction in the shallow mantle wedge

NASA Astrophysics Data System (ADS)

Mitchell, A.; Grove, T. L.

2017-12-01

In subduction zone magmatism, hotter, deeper hydrous mantle melts rise and interact with the shallower, cooler depleted mantle in the uppermost part of the mantle wedge. Here, we experimentally investigate these hydrous reactions using three different ratios of a 1.6 GPa mantle melt and an overlying 1.2 GPa harzburgite from 1060 to 1260 °C. At low ratios of melt/mantle (20:80 and 5:95), the crystallizing assemblages are dunites, harzburgites, and lherzolites (as a function of temperature). When the ratio of deeper melt to overlying mantle is 70:30, the crystallizing assemblage is a wehrlite. This shows that wehrlites, which are observed in ophiolites and mantle xenoliths, can be formed by large amounts of deeper melt fluxing though the mantle wedge during ascent. In all cases, orthopyroxene dissolves in the melt, and olivine crystallizes along with pyroxenes and spinel. The amount of reaction between deeper melts and overlying mantle, simulated here by the three starting compositions, imposes a strong influence on final melt compositions, particularly in terms of depletion. At the lowest melt/mantle ratios, the resulting melt is an extremely depleted Al-poor, high-Si andesite. As the fraction of melt to mantle increases, final melts resemble primitive basaltic andesites found in arcs globally. Wall rock temperature is a key variable; over a span of <80 °C, reaction with deeper melt creates the entire range of mantle lithologies from a depleted dunite to a harzburgite to a refertilized lherzolite. Together, the experimental phase equilibria, melt compositions, and calculated reaction coefficients provide a framework for understanding how melt-wall rock reaction occurs in the natural system during melt ascent in the mantle wedge.

Simulating the behavior of volatiles belonging to the C-O-H-S system in silicate melts under magmatic conditions with the software D-Compress

NASA Astrophysics Data System (ADS)

Burgisser, Alain; Alletti, Marina; Scaillet, Bruno

2015-06-01

Modeling magmatic degassing, or how the volatile distribution between gas and melt changes at pressure varies, is a complex task that involves a large number of thermodynamical relationships and that requires dedicated software. This article presents the software D-Compress, which computes the gas and melt volatile composition of five element sets in magmatic systems (O-H, S-O-H, C-S-O-H, C-S-O-H-Fe, and C-O-H). It has been calibrated so as to simulate the volatiles coexisting with three common types of silicate melts (basalt, phonolite, and rhyolite). Operational temperatures depend on melt composition and range from 790 to 1400 °C. A specificity of D-Compress is the calculation of volatile composition as pressure varies along a (de)compression path between atmospheric and 3000 bars. This software was prepared so as to maximize versatility by proposing different sets of input parameters. In particular, whenever new solubility laws on specific melt compositions are available, the model parameters can be easily tuned to run the code on that composition. Parameter gaps were minimized by including sets of chemical species for which calibration data were available over a wide range of pressure, temperature, and melt composition. A brief description of the model rationale is followed by the presentation of the software capabilities. Examples of use are then presented with outputs comparisons between D-Compress and other currently available thermodynamical models. The compiled software and the source code are available as electronic supplementary materials.

Use of Microgravity to Control the Microstructure of Eutectics

NASA Technical Reports Server (NTRS)

Wilcox, William R.; Regel, Liya L.; Smith, Reginald W.

1999-01-01

The long term goal of this project is to be able to control the microstructure of directionally solidified eutectic alloys, through an improved understanding of the influence of convection. Prior experimental results on the influence of microgravity on the microstructure of fibrous eutectics have been contradictory. Theoretical work at Clarkson University showed that buoyancy-driven convection in the vertical Bridgman configuration is not vigorous enough to alter the concentration field in the melt sufficiently to cause a measurable change in microstructure when the eutectic grows at minimum supercooling. Currently, there are four other hypotheses that might explain the observed changes in microstructure of fibrous eutectics caused by convection: (1) Disturbance of the concentration boundary layer arising from an off-eutectic melt composition and growth at the extremum; (2) Disturbance of the concentration boundary layer of a habit-modifying impurity; (3) Disturbance of the concentration boundary layer arising from an off-eutectic interfacial composition due to non-extremum growth; and (4) A fluctuating freezing rate combined with differences in the kinetics of fiber termination and fiber formation. We favor the last of these hypotheses. Thus, the primary objective of the present grant is to determine experimentally and theoretically the influence of a periodically varying freezing rate on eutectic solidification. A secondary objective is to determine the influence of convection on the microstructure of at least one other eutectic alloy that might be suitable for flight experiments.

Equation of state and phase diagram of Fe-16Si alloy as a candidate component of Earth's core

NASA Astrophysics Data System (ADS)

Fischer, Rebecca A.; Campbell, Andrew J.; Caracas, Razvan; Reaman, Daniel M.; Dera, Przymyslaw; Prakapenka, Vitali B.

2012-12-01

The outer core of the Earth contains several weight percent of one or more unknown light elements, which may include silicon. Therefore it is critical to understand the high pressure-temperature properties and behavior of an iron-silicon alloy with a geophysically relevant composition (16 wt% silicon). We experimentally determined the melting curve, subsolidus phase diagram, and equations of state of all phases of Fe-16 wt%Si to 140 GPa, finding a conversion from the D03 crystal structure to a B2+hcp mixture at high pressures. The melting curve implies that 3520 K is a minimum temperature for the Earth's outer core, if it consists solely of Fe-Si alloy, and that the eutectic composition in the Fe-Si system is less than 16 wt% silicon at core-mantle boundary conditions. Comparing our new equation of state to that of iron and the density of the core, we find that for an Fe-Ni-Si outer core, 11.3±1.5 wt% silicon would be required to match the core's observed density at the core-mantle boundary. We have also performed first-principles calculations of the equations of state of Fe3Si with the D03 structure, hcp iron, and FeSi with the B2 structure using density-functional theory.

Equation of state and phase diagram of Fe-16Si alloy as a candidate component of Earth's core

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, Rebecca A; Campbell, Andrew J; Caracas, Razvan

2016-07-29

The outer core of the Earth contains several weight percent of one or more unknown light elements, which may include silicon. Therefore it is critical to understand the high pressure–temperature properties and behavior of an iron–silicon alloy with a geophysically relevant composition (16 wt% silicon). We experimentally determined the melting curve, subsolidus phase diagram, and equations of state of all phases of Fe–16 wt%Si to 140 GPa, finding a conversion from the D0 3 crystal structure to a B2+hcp mixture at high pressures. The melting curve implies that 3520 K is a minimum temperature for the Earth's outer core, ifmore » it consists solely of Fe–Si alloy, and that the eutectic composition in the Fe–Si system is less than 16 wt% silicon at core–mantle boundary conditions. Comparing our new equation of state to that of iron and the density of the core, we find that for an Fe–Ni–Si outer core, 11.3±1.5 wt% silicon would be required to match the core's observed density at the core–mantle boundary. We have also performed first-principles calculations of the equations of state of Fe 3Si with the D0 3 structure, hcp iron, and FeSi with the B2 structure using density-functional theory.« less

The composition of primary carbonate melts and their evolution through wallrock reaction in the mantle

NASA Astrophysics Data System (ADS)

Dalton, John A.; Wood, Bernard J.

1993-10-01

We have experimentally determined the composition of near-soldus melts from depleted natural Iherzolite at pressures greater than 25 kbar. The melts are carbontitic with low alkali contents and Ca/(Ca + Mg) ratios of 0.72-0.74. Primary carbonate melts from fertile mantle are more sodic with Ca/(Ca + Mg + Fe + Na) of 0.52 and Na/(Na + Ca + Mg + Fe) up to 0.15. The melt compositions are similar to many natural magnesio-carbonatites, but differ substantially from the more abundant calcio-carbonatites. Experimentally we find that calcio-carbonatites are produced by wallrock reaction of primary melts with harzburgite at pressures of less than 25 kbar. At 15 kbar we have obtained a Ca/(Ca + Mg + Fe + Na) ratio of up to 0.87 and very low Na contents generated by this process. Values of Ca/(Ca + Mg + Fe + Na) up to 0.95 are possible at lower pressures. Low pressure wallrock reaction of primary carbonate melt with fertile Iherzolite produces melts richer in Na2CO3, corresponding to possible parental magmas of natrocarbonatite. Wallrock reaction at low pressures transforms the bulk peridotite composition from that of a harzburgite or Iherzolite to wehrlite. Examples of such carbonatite metasomatism are now widely documented. Our experiments show that the calcium content of olivine and the jadeite content of clinopyroxene may be used to constrain the Ca and Na contents respectively of the cabonatite melt responsible for metasomatism.

Compositional Variation in Apollo 16 Impact-Melt Breccias and Inferences for the Geology and Bombardment History of the Central Highlands of the Moon

NASA Technical Reports Server (NTRS)

Korotev, Randy L.

1994-01-01

High-precision data for the concentrations of a number of lithophile and siderophile elements were obtained on multiple subsamples from 109 impact-melt rocks and breccias (mostly crystalline) from the Apollo 16 site. Compositions of nearly all Apollo 16 melt rocks fall on one of two trends of increasing Sm concentration with increasing Sc concentration. The Eastern trend (lower Sm/Sc, Mg/Fe, and Sm/Yb ratios) consists of compositional groups 3 and 4 of previous classification schemes. These melt rocks are feldspathic, poor in incompatible and siderophile elements, and appear to have provenance in the Descartes formation to the east of the site. The Western trend (higher Sm/Sc. Mg/Fe, and Sm/ Yb ratios) consists of compositional groups 1 and 2. These relatively mafic, KREEP-bearing breccias are a major component (approx.35%) of the Cayley plains west of the site and are unusual, compared to otherwise similar melt breccias from other sites, in having high concentrations of Fe-Ni metal ( 1-2 %). The metal is the carrier of the low-Ir/Au (approx. 0.3 x chondritic) siderophile-element signature that is characteristic of the Apollo 16 site. Four compositionally distinct groups (1M, 1F, 2DB, and 2NR) of Western-trend melt breccias occur that are each represented by at least six samples. Compositional group 1 or previous classification schemes (the 'poikilitic' or 'LKFM' melt breccias) can be subdivided into two groups. Group 1M (represented by six samples, including 60315) is characterized by lower Al2O3 concentrations, higher MgO and alkali concentrations, and higher Mg/Fe and Cr/Sc ratios than group 1F (represented by fifteen samples, including 65015). Group 1M also has siderophile-element concentrations averaging about twice those of group lF and Ir/Au and Ir/Ni ratios that are even lower than those of other Western-trend melt rocks (Ir/Au = 0.24 +/- 0.03. CI-normalized). At the mafic extreme of group 2 ('VHA' melt breccias), the melt lithology occurring as clasts in feldspathic fragmental breccias from North Ray crater (group 2NR) is compositionally distinct from the melt lithology ofdimict breccias from the Cayley plains (group 2DB) in having higher concentrations of Sc, Cr, and heavy rare earth elements and lower concentrations of siderophile elements. The distinct siderophile-element signature (high absolute abundances, low Ir/Au ratio) suggest that the four groups ofmafic melt breccia are all somehow related. Ratios ofsome lithophile elements also suggest that they are more closely related to each other than then, are to melt breccias from other Apoll sites. However, none of the breccia compositions can be related to any of the others by any simple process of igneous fractionation or mixing involving common lunar materials. Thus, the origin of the four groups of mafic melt breccia is enigmatic. If they were produced in only one or two impacts, then a mechanism exists for generating regimes of impact-melt breccia in a single impact that are substantially different from each other in composition. For various reasons, including the problem of delivering large volumes of four different types of melt to the Apollo 16 site, it is unlikely that any of these breccias were produced in basin-forming impacts. If they were produced in as many as four crater-forming impacts, then the unusual siderophile-element signature is difficult to explain. Possible explanations are (1) the four groups of melt breccia all contain metal from a single, earlier impact, (2) they were each formed by related metal-rich meteoroids, or (3) some common postimpact process has resulted in metal of similar composition in each of four melt pools. Within a compositional group, most intrasample and intersample variation in lithophile element concentrations is caused by differences among samples in the proportion of a component of normative anorthosite or noritic anorthosite. In most cases, this compositional variation probably reflects variation in clast abundance. For group 2DB (and probably 2NR), differences in abundance of a component of ferroan anorthosite (estimated Al2O3 approx. 32%) accounts for the compositional variation. For groups 1M and 1F, the anorthositic component is more mafic (estimated Al203 approx. 26%). Some group-2 samples may be related by a troctolitic component of varying abundance.

Computational-Experimental Processing of Boride/Carbide Composites by Reactive Infusion of Hf Alloy Melts into B4C

DTIC Science & Technology

2015-09-16

AFRL-AFOSR-VA-TR-2015-0314 Computational -Experimental Processing of Boride /Carbide Composites by Reactive Infusion of Hf Alloy Melts into B4C...Computational -Experimental Processing of Boride /Carbide Composites by Reactive Infusion of Hf Alloy Melts into B4C 5a.  CONTRACT NUMBER 5b.  GRANT...with a packed bed of B4C to form boride - carbide precipitates. Although the ultimate goal of the research endeavor is to enhance significantly the

Partial melting of metagreywackes, Part II. Compositions of minerals and melts

NASA Astrophysics Data System (ADS)

Montel, Jean-Marc; Vielzeuf, Daniel

A series of experiments on the fluid-absent melting of a quartz-rich aluminous metagreywacke has been carried out. In this paper, we report the chemical composition of the phases present in the experimental charges as determined by electron microprobe. This analytical work includes biotite, plagioclase, orthopyroxene, garnet, cordierite, hercynite, staurolite, gedrite, oxide, and glass, over the range 100-1000MPa, 780-1025°C. Biotites are Na- and Mg-rich, with Ti contents increasing with temperature. The compositions of plagioclase range from An17 to An35, with a significant orthoclase component, and are always different from the starting minerals. At high temperature, plagioclase crystals correspond to ternary feldspars with Or contents in the range 11-20 mol%. Garnets are almandine pyrope grossular spessartine solid solutions, with a regular and significant increase of the grossular content with pressure. All glasses are silicic (SiO2=67.6-74.4 wt%), peraluminous, and leucocratic (FeO+MgO=0.9-2.9 wt%), with a bulk composition close to that of peraluminous leucogranites, even for degrees of melting as high as 60 vol.%. With increasing pressure, SiO2 contents decrease while K2O increases. At any pressure, the melt compositions are more potassic than the water-saturated granitic minima. The H2O contents estimated by mass balance are in the range 2.5-5.6 wt%. These values are higher than those predicted by thermodynamic models. Modal compositions were estimated by mass balance calculations and by image processing of the SEM photographs. The positions of the 20 to 70% isotects (curves of equal proportion of melt) have been located in the pressure-temperature space between 100MPa and 1000MPa. With increasing pressure, the isotects shift toward lower temperature between 100 and 200MPa, then bend back toward higher temperature. The melting interval increases with pressure; the difference in temperature between the 20% and the 70% isotects is 40°C at 100MPa, and 150°C at 800MPa. The position of the isotects is interpreted in terms of both the solubility of water in the melt and the nature of the reactions involved in the melting process. A comparison with other partial melting experiments suggests that pelites are the most fertile source rocks above 800MPa. The difference in fertility between pelites and greywackes decreases with decreasing pressure. A review of the glass compositions obtained in experimental studies demonstrates that partial melting of fertile rock types in the crust (greywackes, pelites, or orthogneisses) produces only peraluminous leucogranites. More mafic granitic compositions such as the various types of calk-alkaline rocks, or mafic S-type rocks, have never been obtained during partial melting experiments. Thus, only peraluminous leucogranites may correspond to liquids directly formed by partial melting of metasediments. Other types of granites involve other components or processes, such as restite unmixing from the source region, and/or interaction with mafic mantle-derived materials.

Generation of Primary Kilauea Magmas: Constraints on Pressure, Temperature and Composition of Melts

NASA Astrophysics Data System (ADS)

Gudfinnsson, G. H.; Presnall, D. C.

2004-12-01

Picrite glasses from the submarine extension of Kilauea, Puna Ridge, which contain up to 15.0 wt% MgO, are the most magnesian glass samples reported from Hawaii. Their compositions form a distinct olivine fractionation trend. A comparison of this trend with phase relations of garnet lherzolite in the CaO-MgO-Al2O3-SiO2 (CMAS) and CaO-MgO-Al2O3-SiO2-Na2O-FeO (CMASNF) system indicates that melts parental to the Hawaiian picrites are produced by melting of a garnet lherzolite source at a pressure of 5 ± 1 GPa. The primary melt composition for Kilauea proposed by Clague et al. (1995), which has 18.4 wt% MgO, is close to the expected 5 GPa melt composition. By using the pressure-independent CMASNF geothermometer (Gudfinnsson and Presnall, 2001), we obtain a temperature of formation of 1450° C for the most magnesian Puna Ridge glass after correction for the presence of 0.4 wt% H2O and 0.7 wt% CO2. This assumes that the glass is not much modified after separation from the lherzolite source. However, comparison with phase relations in the CMAS system strongly suggests that the most magnesian Puna Ridge glasses are the product of some olivine fractionation, and therefore give temperature considerably lower than that of the source. When applied to the proposed Kilauea primary melt composition of Clague et al. (1995), the CMASNF geothermometer gives a melting temperature of 1596° C or about 1565° C after correction for the presence of volatiles. This compares well with the anhydrous solidus temperature of 1600 ± 15° C at 5 GPa for the fertile KR4003 lherzolite (Lesher et al., 2003), which has the complete garnet lherzolite phase assemblage present at the solidus at this pressure. This consistency supports use of phase relations from the CMAS system and the CMASNF geothermometer to the Puna Ridge picrite compositions. With the pressure and temperature of melting known, one can calculate the potential temperature of the Hawaiian mantle, provided certain conditions are met. The calculation assumes that the temperature at the point of melt segregation is close to the temperature of the solid adiabat. If extensive melting has occurred prior to the segregation, this will be incorrect. Secondly, it is assumed that the melting is occurring at the non-conducting part of the geotherm. Provided this is the case and the Kilauea primary melt composition truly represents a near-primary melt composition, we derive a potential temperature for the mantle beneath Kilauea of about 1500° C. The very high temperature and pressure conditions for magma generation at Hawaii appear to be unmatched by any other currently active volcanism on the Earth. Thus, of all the candidates for plume status, Hawaii appears to be the most robust.

Young Prehistoric Kilauea Lava Flows From Uwekahuna Bluff, Hawaii: Mixed Source or Hybrid Magmas?

NASA Astrophysics Data System (ADS)

Marske, J. P.; Pietruszka, A. J.; Garcia, M. O.; Norman, M. D.; Rhodes, J. M.

2004-12-01

For the last 350 kyr, nearly the entire known compositional range of subaerial and submarine Kilauea lavas lie within the range defined by the volcano's historical eruptions. In contrast, Rhodes et al. (1989) discovered that some Kilauea lavas have Mauna Loa-like major-and trace-element signatures and concluded that Mauna Loa magmas may periodically invade Kilauea's shallow plumbing system. Here, we present new major- and trace- element data for 25 sequential prehistoric lava flows (0.5 to <2 ka) from the upper 55 m of the north wall of Kilauea caldera at Uwekahuna Bluff (UB). Although historical Kilauea and Mauna Loa lavas have been compositionally distinct for most of the last 230 kyr, our results show that the UB lavas span the geochemical spectrum between these neighboring volcanoes. At a given MgO content, the abundances of major elements (e.g., SiO2, TiO2, or CaO) in the UB lavas typically plot between historical Mauna Loa and Kilauea values, suggesting that these lavas originated from compositionally intermediate parental magmas or from hybridization between historical Kilauea- and Mauna Loa-type magmas. In contrast to the major element abundances, ratios of highly to moderately incompatible elements (e.g., Nb/Y) in the UB lavas are mostly Mauna Loa-like. These incompatible trace element ratios reveal a rapid fluctuation of Kilauea's lava composition since prehistoric times: (1) two lava flows at the base of the suite record a decrease in Nb/Y from historical Kilauea- to historical Mauna Loa-type values, (2) a weathered hiatus near the middle of the flow sequence coincides with a gradual Nb/Y minimum and reversal, and (3) the top three lava flows transition back into historical Kilauea-type Nb/Y values with a smooth temporal connection to the oldest historical lavas from this volcano. The systematic variations of these UB trace-element ratios may result from gradual mixing between Kilauea- and Mauna Loa-type magmas within the summit reservoir and/or varying degrees of partial melting of a Mauna Loa-like mantle heterogeneity within Kilauea's source region. Highly incompatible element ratios (e.g., Rb/Nb), which are typically unaffected by variable melt fraction, indicate that changes in the degree of partial melting alone cannot explain these Mauna Loa-like lava flows. Pb, Sr and Nd isotopic ratios of the Uwekahuna Bluff lavas will be presented to differentiate mantle source and melting effects from magma chamber processes.

Mixing Silicate Melts with High Viscosity Contrast by Chaotic Dynamics: Results from a New Experimental Device

NASA Astrophysics Data System (ADS)

de Campos, Cristina; Perugini, Diego; Ertel-Ingrisch, Werner; Dingwell, Donald B.; Poli, Giampiero

2010-05-01

A new experimental device has been developed to perform chaotic mixing between high viscosity melts under controlled fluid-dynamic conditions. The apparatus is based on the Journal Bearing System (JBS). It consists of an outer cylinder hosting the melts of interest and an inner cylinder, which is eccentrically located. Both cylinders can be independently moved to generate chaotic streamlines in the mixing system. Two experiments were performed using as end-members different proportions of a peralkaline haplogranite and a mafic melt, corresponding to the 1 atm eutectic composition in the An-Di binary system. The two melts were stirred together in the JBS for ca. two hours, at 1,400° C and under laminar fluid dynamic condition (Re of the order of 10-7). The viscosity ratio between the two melts, at the beginning of the experiment, was of the order of 103. Optical analyses of experimental samples revealed, at short length scale (of the order of μm), a complex pattern of mixed structures. These consisted of an intimate distribution of filaments; a complex inter-fingering of the two melts. Such features are typically observed in rocks thought to be produced by magma mixing processes. Stretching and folding dynamics between the melts induced chaotic flow fields and generated wide compositional interfaces. In this way, chemical diffusion processes become more efficient, producing melts with highly heterogeneous compositions. A remarkable modulation of compositional fields has been obtained by performing short time-scale experiments and using melts with a high viscosity ratio. This indicates that chaotic mixing of magmas can be a very efficient process in modulating compositional variability in igneous systems, especially under high viscosity ratios and laminar fluid-dynamic regimes. Our experimental device may replicate magma mixing features, observed in natural rocks, and therefore open new frontiers in the study of this important petrologic and volcanological process.

Composition of primary fluid and melt inclusions in regenerated olivines from hypabyssal kimberlites of the Malokuonapskaya pipe (Yakutia)

NASA Astrophysics Data System (ADS)

Tomilenko, A. A.; Kuzmin, D. V.; Bulbak, T. A.; Timina, T. Yu.; Sobolev, N. V.

2015-11-01

The primary fluid and melt inclusions in regenerated zonal crystals of olivine from kimberlites of the Malokuonapskaya pipe were first examined by means of microthermometry, optic and scanning electron microscopy, and Raman spectroscopy. The high-pressure genesis of homogenous central parts of the olivines was revealed, probably under intense metasomatism at early hypogene stages with subsequent regeneration in the kimberlitic melt. The olivine crystals were regenerated from silicate-carbonate melts at about 1100°C. The composition of the kimberlitic melt was changed by way of an increase in the calcium content.

Effects of Natural Rubber on Microwave Absorption Characteristics of Some Li-Ni-Zn Ferrite-Thermoplastic Natural Rubber Composites

NASA Astrophysics Data System (ADS)

Abdul Hamid, Siti Atkah; Abdullah, Mustaffa Hj.; Ahmad, Sahrim Hj.; Mansor, Abdul Aziz; Yusoff, Ahmad Nazlim

2002-09-01

A microwave (Li0.5Fe0.5)0.4Ni0.3Zn0.3Fe2O4 (LNZ) ferrite was prepared by a conventional sintering method in air. Thermoplastic natural rubber (TPNR) was prepared from polypropylene (PP) and natural rubber (NR) in the ratios of 80:20, 70:30, 60:40, 50:50 and 40:60 with liquid natural rubber as a compatibilizer by a melt blending technique. LNZ ferrite-TPNR composites with 20 wt% ferrite filler were prepared using a Brabender plasticorder internal mixer. The microwave electromagnetic properties of the composites were studied in the frequency range of 0.3-13.5 GHz using a microwave vector network analyzer (MVNA). The real and imaginary components of the relative complex dielectric permittivity (\\varepsilonr*=\\varepsilonr\\prime-j\\varepsilonr\\prime\\prime) and magnetic permeability (μr*=μr\\prime-jμr\\prime\\prime) were calculated from the measured complex scattering parameters (S11* and S12*) using the Nicolson-Ross model. The dielectric and magnetic properties were found to depend on the NR and PP content in the composites. The minimum reflection loss (RL) under the matching conditions increases with increasing NR content.

Origin Of Extreme 3He/4He Signatures In Icelandic Lavas: Insights From Melt Inclusion Studies

NASA Astrophysics Data System (ADS)

Harlou, R.; Kent, A. J.; Breddam, K.; Davidson, J. P.; Pearson, D. G.

2003-12-01

Helium isotopes are considered a powerful tool for tracking different mantle domains. Yet, the origin of He isotope variations in many basaltic suites remains enigmatic and often difficult to link with more lithophile chemical and isotopic tracers. One problem is that He isotope ratios are measured from crushed olivines and thus reflect prior fluid and melt fluxes trapped in inclusions within the olivine grains, whereas the lithophile elements mainly reflect the host lava. In an attempt to link He and lithophile element variations, we have characterized the major and trace element composition including volatile elements, of olivine-hosted melt inclusions from three ankaramitic lavas from Vestfirdir, NW-Iceland. Previous studies have reported extreme 3He/4He ratios from NW-Iceland and one ankaramite (SEL97) has been suggested to provide the most precise estimate of the radiogenic (Sr-Nd-Pb) isotopic composition of a relatively undegassed (high 3He/4He) mantle component (C or FOZO) common to several ocean islands (Hilton et al. 1999, EPSL 173, 53-60). The samples investigated here exhibit amongst the highest 3He/4He ratios observed in terrestrial rocks (42.9 and 34.8 R/Ra). A detailed account of the trace element signature of melt inclusions in these samples may thus help explain the origin of FOZO. One sample of similar composition to these, has a lower He content and a relatively poorly defined He isotope composition of 8.15 +/- 5.1 R/Ra (Breddam & Kurz, 2001, EOS, 82, F1315). In terms of major elements, the whole rock data reflect olivine accumulation, whereas the melt inclusion data reflect ol + cpx fractionation. The melt inclusions are generally basaltic (Mg#: 52-62), with primitive mantle normalised trace element concentrations that are broadly parallel the host lavas. There is little compositional difference between melt inclusion populations from high and low 3He/4He lavas, although inclusions of the low 3He/4He lava have lower S and moderately lower Cl. The observed range of trace element ratios: [La/Sm]N 1-4, [La/Yb]N 1-5, Sr/Nd 14-24, Ba/Rb 9-23, and Ce/Pb 5-46, covers much of the range observed in Icelandic alkali basalts. The compositional similarities between inclusions and host lavas suggests that bulk rock compositions are petrogenetically related to the melts sampled by melt inclusions. If He predominantly resides in these inclusions, it suggests that the whole rock composition is an aggregate derived from the same melts that contain the measured He.

Vapor-Saturated Melting of Fertile Peridotite Revisited: A new Experimental Approach and Re-evaluation of the Hydrous Peridotite Solidus

NASA Astrophysics Data System (ADS)

Grove, T. L.

2001-12-01

The vapor-saturated melting relations of peridotite have been determined for a fertile mantle composition of Hart and Zindler (1986, Chem Geol 57: 247) over the pressure range of 1.2 to 2.4 GPa. For example, at 1.2 GPa melt is present at a temperature of 980° C and at 2.4 GPa melt is present at 920° C. These temperatures should be viewed as maximum values for the vapor-saturated solidus (although see below) because the initial melting temperature of multi-phase, multicomponent systems can often be difficult to detect. At 2.4 GPa the melt composition is highly silica-undersaturated and very aluminous ( ~ 21 wt. % Al2O3). Wet mantle melts are thought to be high in silica, but this is not the case for these hydrous melts. At 1.2 GPa, melt fractions are too small to allow reliable analysis. The experiments have been carried out in a piston cylinder apparatus using Au capsules. The starting material is an oxide mixture containing 14.5 wt. % H2O added as brucite. Free water present in the experiment after quenching indicates subsolidus conditions. The absence of fluid in experiments above the vapor-saturated solidus shows that all of the free H2O is dissolved in the melt. The high H2O content of the starting material moves the bulk composition close to the vapor-saturated melt composition, therefore increasing the amount of melt produced close to the solidus and making detection of low melt fraction possible. Studies of the hydrous peridotite solidus carried out between 1970 and 1975 by Mysen and Boettcher, Kushiro and others, Green and Millhollen and others at 2.0 GPa ranged from < 800 to ~ 1000° C, a variation of over 200 degrees. In a subduction zone environment a fluid-rich component released from the slab ascends into hotter overlying mantle and melting initiates at the vapor-saturated solidus. Melting would begin at a depth of ~ 75 km in the mantle wedge, for a realistic thermal structure. Melting would continue as these initial H2O-rich buoyant melts ascend into hotter, shallower mantle and re-equilibrate with their surroundings. The initiation of melting deep in the mantle wedge has implications for both chemical and mechanical processes in the subduction zone environment.

Do Hf isotopes in magmatic zircons represent those of their host rocks?

NASA Astrophysics Data System (ADS)

Wang, Di; Wang, Xiao-Lei; Cai, Yue; Goldstein, Steven L.; Yang, Tao

2018-04-01

Lu-Hf isotopic system in zircon is a powerful and widely used geochemical tracer in studying petrogenesis of magmatic rocks and crustal evolution, assuming that zircon Hf isotopes can represent initial Hf isotopes of their parental whole rock. However, this assumption may not always be valid. Disequilibrium partial melting of continental crust would preferentially melt out non-zircon minerals with high time-integrated Lu/Hf ratios and generate partial melts with Hf isotope compositions that are more radiogenic than those of its magma source. Dissolution experiments (with hotplate, bomb and sintering procedures) of zircon-bearing samples demonstrate this disequilibrium effect where partial dissolution yielded variable and more radiogenic Hf isotope compositions than fully dissolved samples. A case study from the Neoproterozoic Jiuling batholith in southern China shows that about half of the investigated samples show decoupled Hf isotopes between zircons and the bulk rocks. This decoupling could reflect complex and prolonged magmatic processes, such as crustal assimilation, magma mixing, and disequilibrium melting, which are consistent with the wide temperature spectrum from ∼630 °C to ∼900 °C by Ti-in-zircon thermometer. We suggest that magmatic zircons may only record the Hf isotopic composition of their surrounding melt during crystallization and it is uncertain whether their Hf isotopic compositions can represent the primary Hf isotopic compositions of the bulk magmas. In this regard, using zircon Hf isotopic compositions to trace crustal evolution may be biased since most of these could be originally from disequilibrium partial melts.

Slab-derived metasomatism in the Carpathian-Pannonian mantle revealed by investigations of mantle xenoliths from the Bakony-Balaton Highland Volcanic Field

NASA Astrophysics Data System (ADS)

Créon, Laura; Delpech, Guillaume; Rouchon, Virgile; Guyot, François

2017-08-01

A suite of fifteen peridotite xenoliths from the Bakony-Balaton Highland Volcanic Field (BBHVF, Pannonian Basin, Central Europe) that show abundant petrographic evidence of fluid and melt percolation were studied in order to decipher the formation of their melt pockets and veins. The suite mainly consists of "fertile" lherzolites (5.8-19.9 vol.% clinopyroxene) and a few harzburgites (1.9-5.4 vol.% clinopyroxene) from well-known localities (Szentbékkálla, Szigliget) and two previously unreported localities (Füzes-tó and Mindszentkálla). Major and trace element data indicate that most of the peridotites record variable degrees of partial melt extraction, up to > 15% for the harzburgites. Subsequently, the xenoliths experienced at least two stages of metasomatic modification. The first stage was associated with percolation of a volatile-bearing silicate melt and resulted in crystallization of amphibole, enrichment in the most incompatible trace elements (Ba, Th, U, Sr), and development of negative Nb-Ta anomalies in clinopyroxene. The second and last metasomatic event, widespread beneath the BBHVF, is associated with the formation of silicate melt pockets, physically connected to a network of melt veins, with large and abundant CO2 vesicles. The glass in these veins has sub-alkaline trachy-andesitic composition and displays an OIB-like trace element signature. Its composition attests to the migration through a supra-subduction zone mantle wedge of silicic melt highly enriched in volatiles (CO2, H2O, Cl, F), LILE, REE and HFSE and consistent with compositions of natural and experimental examples of slab melting-derived magma. In the present case, however, melt was likely derived from melting of oceanic crust and carbonated sediments under conditions where Nb-rich mineral phases were not stable in the residue. A likely scenario for the origin such melts involves melting after subduction ceased as the slab thermally equilibrated with the asthenosphere. Melt-rock reactions due to ascent of hot, CO2-rich, siliceous melt to near-Moho depths triggered destabilization of amphibole and primary clinopyroxene, spinel, and possibly olivine. The resulting andesitic glass in melt pockets evolved to more mafic compositions due to mantle mineral assimilation but has heterogeneous trace element signatures mostly inherited from preexisting amphibole. The present example of melt-rock reactions between highly volatile-enriched siliceous slab-derived melt and peridotite from the upper part of the lithospheric mantle ultimately produced derivative melt with major element composition akin to calc-alkaline basaltic andesite, with generally low trace elements concentrations but selective pronounced enrichments in LILE's such as Ba, Sr, Pb.

A Study of Melt Inclusions in Tin-Mineralized Granites From Zinnwald, Germany

NASA Astrophysics Data System (ADS)

Sookdeo, C. A.; Webster, J. D.; Eschen, M. L.; Tappen, C. M.

2001-12-01

We have analyzed silicate melt inclusions from drill core samples from the eastern Erzgebirge region, Germany, to investigate magmatic-hydrothermal and mineralizing processes in compositionally evolved, tin-bearing granitic magmas. Silicate melt inclusions are small blebs of glass that are trapped or locked within phenocrysts and may contain high concentrations of volatiles that usually leave magma via degassing. Quartz phenocrysts were carefully hand picked from crushed samples of albite-, zinnwaldite- +/- lepidolite-bearing granitic dikes from Zinnwald and soaked in cold dilute HF to remove any attached groundmass. The cleaned phenocrysts were loaded into precious metal capsules with several drops of immersion oil to create a reducing environment at high temperature. The quartz-bearing capsules were inserted into quartz glass tubes, loaded into a furnace for heating at temperatures of 1025\\deg and 1050\\deg C (1atm) for periods of 20 to 30 hours, and subsequently the inclusions were quenched to glass. The inclusions were analyzed for major and minor elements (including F, Cl, and P) by electron microprobe and for H2O, trace elements, and ore elements by ion microprobe. The melt inclusion compositions are similar to that of the whole-rock sample from which the quartz separates were extracted. The average melt inclusion and whole-rock compositions are peraluminous, high in silica and rare alkalis, and low in MgO, CaO, FeO, MnO, and P2O5. Unlike the whole-rock sample, the melt inclusions contain from 0.5 to more than 4 wt.% F. The Cl contents of the inclusions are variable and range from hundreds of ppm to several thousand ppm. The variable and strong enrichments in F of the melt inclusions may correlate with (Na2O/Na2O+K2O) in the inclusions which is consistent with crystal fractionation of feldspars which drives the residual melt to increasing Na contents. Overall, the compositions of these melt inclusions are different from melt inclusions extracted from the highly peraluminous, tin-mineralized granites of the western Erzgebirge region. The latter represent extreme compositional evolution of P- and F-rich magmas. The inclusions from the albite-, zinnwaldite-, +/- lepidolite-bearing granitic dikes of Zinnwald are more similar, compositionally, to those in tin-mineralized rhyolites of Mexico and New Mexico; the Erzgebirge dike melt inclusions container comparatively greater abundances of Li, Sn, and F, however.

Evaluation of a Melt Infiltrated SiC/SiC Ceramic Matrix Composite

DTIC Science & Technology

2017-12-20

AFRL-RX-WP-TR-2018-0080 EVALUATION OF A MELT INFILTRATED SIC/SIC CERAMIC MATRIX COMPOSITE Larry P. Zawada Universal Technology...REPORT TYPE 3. DATES COVERED (From - To) 20 December 2017 Final 1 January 2009 – 20 November 2017 4. TITLE AND SUBTITLE EVALUATION OF A MELT...4 3.1 Materials Description .....................................................................................................4 3.2 Purchase and

Eruption style at Kīlauea Volcano in Hawai‘i linked to primary melt composition

USGS Publications Warehouse

Sides. I.R.,; Edmonds, M.; Maclennan, J.; Swanson, Don; Houghton, Bruce F.

2014-01-01

Explosive eruptions at basaltic volcanoes have been linked to gas segregation from magmas at shallow depths in the crust. The composition of primary melts formed at greater depths was thought to have little influence on eruptive style. Ocean island basaltic volcanoes are the product of melting of a geochemically heterogeneous mantle plume and are expected to give rise to heterogeneous primary melts. This range in primary melt composition, particularly with respect to the volatile components, will profoundly influence magma buoyancy, storage and eruption style. Here we analyse the geochemistry of a suite of melt inclusions from 25 historical eruptions at the ocean island volcano of Kīlauea, Hawai‘i, over the past 600 years. We find that more explosive styles of eruption at Kīlauea Volcano are associated statistically with more geochemically enriched primary melts that have higher volatile concentrations. These enriched melts ascend faster and retain their primary nature, undergoing little interaction with the magma reservoir at the volcano’s summit. We conclude that the eruption style and magma-supply rate at Kīlauea are fundamentally linked to the geochemistry of the primary melts formed deep below the volcano. Magmas might therefore be predisposed towards explosivity right at the point of formation in their mantle source region.

Partitioning of Ni, Co and V between Spinel-Structured Oxides and Silicate Melts: Importance of Spinel Composition

NASA Technical Reports Server (NTRS)

Righter, K.; Leeman, W. P.; Hervig, R. L.

2006-01-01

Partitioning of Ni, Co and V between Cr-rich spinels and basaltic melt has been studied experimentally between 1150 and 1325 C, and at controlled oxygen fugacity from the Co-CoO buffer to slightly above the hematite magnetite buffer. These new results, together with new Ni, Co and V analyses of experimental run products from Leeman [Leeman, W.P., 1974. Experimental determination of the partitioning of divalent cations between olivine and basaltic liquid, Pt. II. PhD thesis, Univ. Oregon, 231 - 337.], show that experimentally determined spinel melt partition coefficients (D) are dependent upon temperature (T), oxygen fugacity (fO2) and spinel composition. In particular, partition coefficients determined on doped systems are higher than those in natural (undoped) systems, perhaps due to changing activity coefficients over the composition range defined by the experimental data. Using our new results and published runs (n =85), we obtain a multilinear regression equation that predicts experimental D(V) values as a function of T, fO2, concentration of V in melt and spinel composition. This equation allows prediction of D(V) spinel/melt values for natural mafic liquids at relevant crystallization conditions. Similarly, D(Ni) and D(Co) values can be inferred from our experiments at redox conditions approaching the QFM buffer, temperatures of 1150 to 1250 C and spinel composition (early Cr-bearing and later Ti-magnetite) appropriate for basic magma differentiation. When coupled with major element modelling of liquid lines of descent, these values (D(Ni) sp/melt=10 and D(Co) sp/melt=5) closely reproduce the compositional variation observed in komatiite, mid-ocean ridge basalt (MORB), ocean island basalt (OIB) and basalt to rhyolite suites.

Low-Degree Partial Melting Experiments of CR and H Chondrite Compositions: Implications for Asteroidal Magmatism Recorded in GRA 06128 and GRA 06129 T

NASA Technical Reports Server (NTRS)

Usui, T.; Jones, John H.; Mittlefehldt, D. W.

2010-01-01

Studies of differentiated meteorites have revealed a diversity of differentiation processes on their parental asteroids; these differentiation mechanisms range from whole-scale melting to partial melting without the core formation [e.g., 1]. Recently discovered paired achondrites GRA 06128 and GRA 06129 (hereafter referred to as GRA) represent unique asteroidal magmatic processes. These meteorites are characterized by high abundances of sodic plagioclase and alkali-rich whole-rock compositions, implying that they could originate from a low-degree partial melt from a volatile-rich oxidized asteroid [e.g., 2, 3, 4]. These conditions are consistent with the high abundances of highly siderophile elements, suggesting that their parent asteroid did not segregate a metallic core [2]. In this study, we test the hypothesis that low-degree partial melts of chondritic precursors under oxidizing conditions can explain the whole-rock and mineral chemistry of GRA based on melting experiments of synthesized CR- and H-chondrite compositions.

Polymineralic inclusions in mantle chromitites from the Oman ophiolite indicate a highly magnesian parental melt

NASA Astrophysics Data System (ADS)

Rollinson, Hugh; Mameri, Lucan; Barry, Tiffany

2018-06-01

Polymineralic inclusions interpreted as melt inclusions in chromite from the dunitic Moho Transition Zone in the Maqsad area of the Oman ophiolite have been analysed and compositions integrated using a rastering technique on the scanning electron microscope. The inclusions now comprise a range of inter-grown hydrous phases including pargasite, aspidolite, phlogopite and chlorite, indicating that the parental melts were hydrous. Average inclusion compositions for seven samples contain between 23.1 and 26.8 wt% MgO and 1.7-3.6 wt% FeO. Compositions were corrected to allow for the low FeO concentrations using coexisting olivine compositions. These suggest that the primary melt has between 20 and 22 wt% MgO and 7-9.7 wt% FeO and has an affinity with boninitic melts, although the melts have a higher Ti content than most boninites. Average rare earth element concentrations suggest that the melts were derived from a REE depleted mantle source although fluid-mobile trace elements indicate a more enriched source. Given the hydrous nature of the inclusions this enrichment could be fluid driven. An estimate of the melt temperature can be made from the results of homogenisation experiments on these inclusions and suggests 1300 °C, which implies for a harzburgite solidus, relatively shallow melting at depths of <50 km and is consistent with a boninitic origin. The current "basaltic" nature of the chromite host to highly magnesian melt inclusions suggests that the dunitic Moho Transition Zone operated as a reaction filter in which magnesian melts were transformed into basalts by the removal of high magnesian olivines, particularly in areas where the Moho Transition Zone is unusually thick. We propose therefore that podiform mantle chromitites, even those with an apparent MORB-like chemical signature, have crystallised from a highly magnesian parental melt. The data presented here strongly support the view that this took place in a subduction initiation setting.

Using MELTS to understand the evolution of silicic magmas: Challenges and successes in modeling the Highland Range Volcanic Sequence (NV)

NASA Astrophysics Data System (ADS)

Vaum, R. C.; Gualda, G. A.; Ghiorso, M. S.; Miller, C. F.; Colombini, L. L.

2009-12-01

The Highland Range near Searchlight, Nevada is comprised of mid-Miocene, intermediate to silicic volcanic rocks. This study focuses on the most silicic portion of the eruptive sequence (16.0-16.5 Ma). The first eruptions during this interval were effusive and produced trachydacite (66-70 wt% SiO2), but later the eruptive style shifted to explosive and compositions were more evolved (70-78 wt% SiO2). Glass compositions in rocks saturated in both quartz and sanidine align along the 150 MPa quartz+sanidine saturation surface, suggesting that the Highland Range magmas equilibrated in a single reservoir at that pressure. We are interested in better understanding this transition in eruptive style from effusive to eruptive, and our approach is based on modeling melt evolution using MELTS thermodynamic modeling software. We selected representative samples from key stratigraphic units, and focused on samples for which whole-rock and glass compositions, as well as mineral abundances, are available. This allows for direct comparison of simulation results with existing data. Initial simulations showed that MELTS predicts unrealistic paths of evolution when compared to the glass compositions and to the phase relations in the Qz-Ab-Or ternary. In particular, the stability field of quartz predicted by MELTS is much too small, causing melts to become exceedingly silicic (>80 wt% SiO2). Sanidine, on the other hand, has fairly sodic compositions and crystallizes too early in the sequence; therefore, simulated melt compositions are never as potassic as the analyzed glasses. Similar results are obtained when modeling the evolution of the Bishop and Campanian magmas, showing that these are systematic problems in MELTS calibration. Accordingly, we have adjusted the enthalpy of quartz and potassium end-member of the feldspar solid solution in MELTS so that the quartz-sanidine saturation surface is correctly predicted. We find that this modified version of MELTS much better models the evolution of silicic magmas. Sanidine begins to crystallize at lower temperatures, causing evolved melts to become significantly more potassic. Also, MELTS prediction of quartz saturation is in agreement with the position of the experimentally determined 150 MPa quartz+sanidine saturation surface. Importantly, the melt evolution that this modified version of MELTS predicts is very consistent with whole-rock data, glass chemistry, and mineral abundances in samples from the Highland Range. Simulations using the modified version of MELTS show that it works remarkably well, at least for relatively low degrees of crystallization. But a more reliable model to simulate the evolution of silicic magmas is necessary to more properly simulate the evolution of silicic systems, in particular at high degrees of crystallinity. We are currently working to create gMELTS, an associated solution model of the haplogranitic system, which, once completed, will be optimized to simulate the evolution of silicic systems.

Melting and dissolution of subducting crust at high pressures: the key role of white mica

NASA Astrophysics Data System (ADS)

Schmidt, Max W.; Vielzeuf, Daniel; Auzanneau, Estelle

2004-11-01

Conditions of melting in the crust are generally controlled by the availability of aqueous fluid and, in the absence of fluid, by the stability of hydroxylated minerals. To depths of 80-90 km, melting is controlled by amphibole and biotite. At greater depths, both phases are unstable in crustal compositions. Simultaneous experiments on a mid-ocean ridge basalt (MORB), a greywacke, and a pelite with excess H2O of 0.4-1.4 wt.% demonstrate that, at >100 km depth (≥3.5 GPa), all three bulk compositions are composed of garnet+clinopyroxene+phengite+coesite±kyanite±rutile, phengitic white mica being the only hydrous mineral present at near-melting temperatures. At 4 GPa, melting reactions, temperatures, and initial melt compositions are thus similar in the entire subducted crust. Fluid-saturated initial melting takes place near 850 °C and melt productivities are proportional to phengite contents. All three bulk compositions produce initially slightly peraluminous potassic Si-rich granites with K:Na molar ratios of 1.4-2.0 and containing 8-13 wt.% H2O. The relatively low Na-contents of these melts result from clinopyroxene/melt partitioning coefficients (Dcpx/melt) of 2.2-4.0 at near solidus temperatures. At higher pressures (≥6.5 GPa), we infer that classical melting does not take place. Instead, the bulk H2O-contents (1.5-2.1 wt.%) in the starting materials, although low, are apparently sufficient to dissolve phengite entirely near 1050 °C. This suggests that pressure conditions beyond the singular endpoint (or second critical point) which terminates the wet solidus as defined by Ricci in 1951 [J.E. Ricci, The phase rule and heterogeneous equilibrium, Dover Publications, Inc. New York (1951) 505 p.] were reached for all three bulk compositions. Extraction of these "supercritical" solute-rich (but Na-poor) melts, which contain about 30-40% H2O, or extraction of the potassic granite melts at lower pressure leave an anhydrous garnet+clinopyroxene±coesite±kyanite±rutile residue. Our results suggest that, except for extremely cold subduction zones, the subducting crust will lose all its potassium (and most of B, Be, Rb, and Ba, and other phengite-hosted trace elements) through leaching or melting during its descent to 300 km. The potassium-rich silica-saturated liquids will immediately react with the peridotite when entering the mantle wedge thus creating source regions for ultrapotassic magmas.

Origin of Aphyric Phonolitic Magmas: Natural Evidences and Experimental Constraints

NASA Astrophysics Data System (ADS)

Masotta, M.; Freda, C.; Gaeta, M.

2010-12-01

Large explosive phonolitic eruptions are commonly characterised by aphyric juvenile eruptive products. Taking into account the low density contrast among phonolitic composition and settling phases (i.e., feldspar and leucite), the almost complete lack of crystals in these differentiated compositions rises the question of which process could produce such an efficient crystal-melt separation. Seeking for an answer, we have investigated crystallization in presence of a thermal gradient as a possible mechanism for crystal-melt separation, considering both chemical and physical effects acting on a variably crystallized system. Using a natural tephri-phonolitic composition as starting material (M.te Aguzzo scoria cone, Sabatini Volcanic District, Central Italy), we have reproduced thermal gradient-driven crystallization in order to simulate the crystallization process in a thermally zoned magma chamber. Crystallization degree (paragenesis made of clinopyroxene±feldspars±leucite) as well as melt composition varies along the thermal gradient. In particular, melt composition ranges from the tephri-phonolitic starting composition at the bottom of the charge (hottest and aphyric zone) to phonolitic at the top (cooler and heterogeneously-crystallised zone). Backscattered images of experimental products clearly evidence: i) the aphyric tephri-phonolitic melt region at the bottom of the charge; ii) a drop-shaped crystal clustering in the middle zone; and iii) large aphyric belt and pockets (up to 100 µm wide) of phonolitic melt, with large deformed-shaped sanidine occurring at their margin, at the charge top region. The latter two features, resulting from solid-melt displacements, suggest that the segregation of phonolitic melt can be related to crystal sinking and compaction. On the other hand, the compositional variability of the melt along the thermal gradient is directly related to the crystallization degree, indicating that chemical diffusion and thermal migration have negligible effect at the experimental scale. Experimental results suggest that, in presence of a thermal gradient, a filter-press differentiation mechanism (i.e. sinking+compaction) is able to produce heterogeneous magma differentiation characterised by a wide range of melt compositions (in our case from tephri-phonolitic to phonolitic). Although the limitation due to the vertical shape of the charge and consequent shear effects occurring at the lateral walls (thus limiting the mobility of the crystal clusters), experimental duration of 24 h is enough to allow crystal-melt separation by means of settling and compaction, indicating that timescale for such a process is extremely rapid and effective at experimental conditions. Actually, experimental textures and phase relations are in good agreement with those observed in natural lithic enclaves (from Sabatini Volcanic District) representative of the crystallizing boundary layer of a phonolitic magma chamber. Thus, we speculate that gravitative collapses of a mushy zone from the magma chamber roof of a thermally zoned magma chamber may produce top accumulation of highly differentiated and aphyric melts.

Markers of the pyroxenite contribution in the major-element compositions of oceanic basalts: Review of the experimental constraints

NASA Astrophysics Data System (ADS)

Lambart, Sarah; Laporte, Didier; Schiano, Pierre

2013-02-01

Based on previous and new results on partial melting experiments of pyroxenites at high pressure, we attempt to identify the major element signature of pyroxenite partial melts and to evaluate to what extent this signature can be transmitted to the basalts erupted at oceanic islands and mid-ocean ridges. Although peridotite is the dominant source lithology in the Earth's upper mantle, the ubiquity of pyroxenites in mantle xenoliths and in ultramafic massifs, and the isotopic and trace elements variability of oceanic basalts suggest that these lithologies could significantly contribute to the generation of basaltic magmas. The question is how and to what degree the melting of pyroxenites can impact the major-element composition of oceanic basalts. The review of experimental phase equilibria of pyroxenites shows that the thermal divide, defined by the aluminous pyroxene plane, separates silica-excess pyroxenites (SE pyroxenites) on the right side and silica-deficient pyroxenites (SD pyroxenites) on the left side. It therefore controls the melting phase relations of pyroxenites at high pressure but, the pressure at which the thermal divide becomes effective, depends on the bulk composition; partial melt compositions of pyroxenites are strongly influenced by non-CMAS elements (especially FeO, TiO2, Na2O and K2O) and show a progressive transition from the liquids derived from the most silica-deficient compositions to those derived from the most silica-excess compositions. Another important aspect for the identification of source lithology is that, at identical pressure and temperature conditions, many pyroxenites produce melts that are quite similar to peridotite-derived melts, making the determination of the presence of pyroxenite in the source regions of oceanic basalts difficult; only pyroxenites able to produce melts with low SiO2 and high FeO contents can be identified on the basis of the major-element compositions of basalts. In the case of oceanic island basalts, high CaO/Al2O3 ratios can also reveal the presence of pyroxenite in the source-regions. Experimental and thermodynamical observations also suggest that the interactions between pyroxenite-derived melts and host peridotites play a crucial role in the genesis of oceanic basalts by generating a wide range of pyroxenites in the upper mantle: partial melting of such secondary pyroxenites is able to reproduce the features of primitive basalts, especially their high MgO contents, and to impart, at least in some cases, the major-element signature of the original pyroxenite melt to the oceanic basalts. Finally, we highlight that the fact the very silica depleted compositions (SiO2 < 42 wt.%) and high TiO2 contents of some ocean island basalts seem to require the contribution of fluids (CO2 or H2O) through melting of either carbonated lithologies (peridotite or pyroxenite) or amphibole-rich veins.

Derivation of intermediate to silicic magma from the basalt analyzed at the Vega 2 landing site, Venus.

PubMed

Shellnutt, J Gregory

2018-01-01

Geochemical modeling using the basalt composition analyzed at the Vega 2 landing site indicates that intermediate to silicic liquids can be generated by fractional crystallization and equilibrium partial melting. Fractional crystallization modeling using variable pressures (0.01 GPa to 0.5 GPa) and relative oxidation states (FMQ 0 and FMQ -1) of either a wet (H2O = 0.5 wt%) or dry (H2O = 0 wt%) parental magma can yield silicic (SiO2 > 60 wt%) compositions that are similar to terrestrial ferroan rhyolite. Hydrous (H2O = 0.5 wt%) partial melting can yield intermediate (trachyandesite to andesite) to silicic (trachydacite) compositions at all pressures but requires relatively high temperatures (≥ 950°C) to generate the initial melt at intermediate to low pressure whereas at high pressure (0.5 GPa) the first melts will be generated at much lower temperatures (< 800°C). Anhydrous partial melt modeling yielded mafic (basaltic andesite) and alkaline compositions (trachybasalt) but the temperature required to produce the first liquid is very high (≥ 1130°C). Consequently, anhydrous partial melting is an unlikely process to generate derivative liquids. The modeling results indicate that, under certain conditions, the Vega 2 composition can generate silicic liquids that produce granitic and rhyolitic rocks. The implication is that silicic igneous rocks may form a small but important component of the northeast Aphrodite Terra.

Derivation of intermediate to silicic magma from the basalt analyzed at the Vega 2 landing site, Venus

PubMed Central

2018-01-01

Geochemical modeling using the basalt composition analyzed at the Vega 2 landing site indicates that intermediate to silicic liquids can be generated by fractional crystallization and equilibrium partial melting. Fractional crystallization modeling using variable pressures (0.01 GPa to 0.5 GPa) and relative oxidation states (FMQ 0 and FMQ -1) of either a wet (H2O = 0.5 wt%) or dry (H2O = 0 wt%) parental magma can yield silicic (SiO2 > 60 wt%) compositions that are similar to terrestrial ferroan rhyolite. Hydrous (H2O = 0.5 wt%) partial melting can yield intermediate (trachyandesite to andesite) to silicic (trachydacite) compositions at all pressures but requires relatively high temperatures (≥ 950°C) to generate the initial melt at intermediate to low pressure whereas at high pressure (0.5 GPa) the first melts will be generated at much lower temperatures (< 800°C). Anhydrous partial melt modeling yielded mafic (basaltic andesite) and alkaline compositions (trachybasalt) but the temperature required to produce the first liquid is very high (≥ 1130°C). Consequently, anhydrous partial melting is an unlikely process to generate derivative liquids. The modeling results indicate that, under certain conditions, the Vega 2 composition can generate silicic liquids that produce granitic and rhyolitic rocks. The implication is that silicic igneous rocks may form a small but important component of the northeast Aphrodite Terra. PMID:29584745

Evolution of Shock Melt Compositions in Lunar Agglutinates

NASA Technical Reports Server (NTRS)

Vance, A. M.; Christoffersen, R.; Keller, L. P.

2015-01-01

Lunar agglutinates are aggregates of regolith grains fused together in a glassy matrix of shock melt produced during smaller-scale (mostly micrometeorite) impacts. Agglutinate formation is a key space weathering process under which the optically-active component of nanophase metallic Fe (npFe(sup 0)) is added to the lunar regolith. Here we have used energy-dispersive X-ray (EDX) compositional spectrum imaging in the SEM to quantify the chemical homogeneity of agglutinitic glass, correlate its homogeneity to its parent soil maturity, and identify the principle chemical components contributing to the shock melt compositional variations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermes, Robert E.

An encapsulated composition for polymerization includes an initiator composition for initiating a polymerization reaction, and a capsule prepared from an elemental metal or fusible alloy having a melting temperature from about 20.degree. C. to about 200.degree. C. A fluid for polymerization includes the encapsulated composition and a monomer. When the capsule melts or breaks open, the initiator is released.

Experimental Constraints on the Chemical Differentiation of Mercurys Mantle

NASA Technical Reports Server (NTRS)

Boujibar, A.; Righter, K.; Pando, K.; Danielson, L.

2015-01-01

Mercury is known as being the most reduced terrestrial planet with the highest core/mantle ratio. Results from MESSENGER spacecraft have shown that its surface is FeO-poor (2-4 wt%) and S-rich (up to 6-7 wt%), which confirms the reducing nature of its silicate mantle. In addition several features suggest important melting stages of the Mercurian mantle: widespread volcanic deposits on its surface, a high crustal thickness (approximately 10% of the planet's volume) and chemical compositions of its surface suggesting several stages of differentiation and remelting processes. Therefore it is likely that igneous processes like magma ocean crystallization and continuous melting have induced chemical and mineralogical heterogeneities in the Mercurian mantle. The extent and nature of compositional variations produced by partial melting remains poorly constrained for the particular compositions of Mercury (very reducing conditions, low FeO-contents and high sulfur-contents). Melting experiments with bulk Mercury-analogue compositions are scarce and with poorly con-trolled starting compositions. Therefore additional experimental data are needed to better understand the differentiation processes that lead to the observed chemical compositions of Mercury's surface.

Method of making silicon carbide-silicon composite having improved oxidation resistance

NASA Technical Reports Server (NTRS)

Wang, Hongyu (Inventor); Luthra, Krishan Lal (Inventor)

2002-01-01

A Silicon carbide-silicon matrix composite having improved oxidation resistance at high temperatures in dry or water-containing environments is provided. A method is given for sealing matrix cracks in situ in melt infiltrated silicon carbide-silicon matrix composites. The composite cracks are sealed by the addition of various additives, such as boron compounds, into the melt infiltrated silicon carbide-silicon matrix.

Silicon carbide-silicon composite having improved oxidation resistance and method of making

NASA Technical Reports Server (NTRS)

Wang, Hongyu (Inventor); Luthra, Krishan Lal (Inventor)

1999-01-01

A Silicon carbide-silicon matrix composite having improved oxidation resistance at high temperatures in dry or water-containing environments is provided. A method is given for sealing matrix cracks in situ in melt infiltrated silicon carbide-silicon matrix composites. The composite cracks are sealed by the addition of various additives, such as boron compounds, into the melt infiltrated silicon carbide-silicon matrix.

Characterization of frictional melting processes in subduction zone faults by trace element and isotope analyses

NASA Astrophysics Data System (ADS)

Ishikawa, T.; Ujiie, K.

2017-12-01

Pseudotachylytes found in exhumed accretionary complexes, which are considered to be formed originally at seismogenic depths, are of great importance for elucidating frictional melting and concomitant dynamic weakening of the fault during earthquake in subduction zones. However, fluid-rich environment of the subduction zone faults tends to cause extensive alteration of the pseudotachylyte glass matrix in later stages, and thus it has been controversial that pseudotachylytes are rarely formed or rarely preserved. Chemical analysis of the fault rocks, especially on fluid-immobile trace elements and isotopes, can be a useful means to identify and quantify the frictional melting occurred in subduction zone faults. In this paper, we report major and trace element and Sr isotope compositions for pseudotachylyte-bearing dark veins and surrounding host rocks from the Mugi area of the Shimanto accretionary complex (Ujiie et al., J. Struct. Geol. 2007). Samples were collected from a rock chip along the microstructure using a micro-drilling technique, and then analyzed by ICP-MS and TIMS. Major element compositions of the dark veins showed a clear shift from the host rock composition toward the illite composition. The dark veins, either unaltered or completely altered, were also characterized by extreme enrichment in some of the trace elements such as Ti, Zr, Nb and Th. These results are consistent with disequilibrium melting of the fault zone. Model calculations revealed that the compositions of the dark veins can be produced by total melting of clay-rich matrix in the source rock, leaving plagioclase and quartz grains almost unmolten. The calculations also showed that the dark veins are far more enriched in melt component than that expected from the source rock compositions, suggesting migration and concentration of frictional melt during the earthquake faulting. Furthermore, Sr isotope data of the dark veins implied the occurrence of frictional melting in multiple stages. These results demonstrate that trace element and isotope analyses are useful not only to detect preexistence of pseudotachylytes but also to evaluate the frictional melting in subduction zone faults quantitatively.

Evidence for chemically heterogeneous Arctic mantle beneath the Gakkel Ridge

NASA Astrophysics Data System (ADS)

D'Errico, Megan E.; Warren, Jessica M.; Godard, Marguerite

2016-02-01

Ultraslow spreading at mid-ocean ridges limits melting due to on-axis conductive cooling, leading to the prediction that peridotites from these ridges are relatively fertile. To test this, we examined abyssal peridotites from the Gakkel Ridge, the slowest spreading ridge in the global ocean ridge system. Major and trace element concentrations in pyroxene and olivine minerals are reported for 14 dredged abyssal peridotite samples from the Sparsely Magmatic (SMZ) and Eastern Volcanic (EVZ) Zones. We observe large compositional variations among peridotites from the same dredge and among dredges in close proximity to each other. Modeling of lherzolite trace element compositions indicates varying degrees of non-modal fractional mantle melting, whereas most harzburgite samples require open-system melting involving interaction with a percolating melt. All peridotite chemistry suggests significant melting that would generate a thick crust, which is inconsistent with geophysical observations at Gakkel Ridge. The refractory harzburgites and thin overlying oceanic crust are best explained by low present-day melting of a previously melted heterogeneous mantle. Observed peridotite compositional variations and evidence for melt infiltration demonstrates that fertile mantle components are present and co-existing with infertile mantle components. Melt generated in the Gakkel mantle becomes trapped on short length-scales, which produces selective enrichments in very incompatible rare earth elements. Melt migration and extraction may be significantly controlled by the thick lithosphere induced by cooling at such slow spreading rates. We propose the heterogeneous mantle that exists beneath Gakkel Ridge is the consequence of ancient melting, combined with subsequent melt percolation and entrapment.

The record of mantle heterogeneity preserved in Earth's oceanic crust

NASA Astrophysics Data System (ADS)

Burton, K. W.; Parkinson, I. J.; Schiano, P.; Gannoun, A.; Laubier, M.

2017-12-01

Earth's oceanic crust is produced by melting of the upper mantle where it upwells beneath mid-ocean ridges, and provides a geographically widespread elemental and isotopic `sample' of Earth's mantle. The chemistry of mid-ocean ridge basalts (MORB), therefore, holds key information on the compositional diversity of the upper mantle, but the problem remains that mixing and reaction during melt ascent acts to homogenise the chemical variations they acquire. Nearly all isotope and elemental data obtained thus far are for measurements of MORB glass, and this represents the final melt to crystallise, evolving in an open system. However, the crystals that are present are often not in equilibrium with their glass host. Melts trapped in these minerals indicate that they crystallised from primitive magmas that possess diverse compositions compared to the glass. Therefore, these melt inclusions preserve information on the true extent of the mantle that sources MORB, but are rarely amenable to precise isotope measurement. An alternative approach is to measure the isotope composition of the primitive minerals themselves. Our new isotope data indicates that these minerals crystallised from melts with significantly different isotope compositions to their glass host, pointing to a mantle source that has experienced extreme melt depletion. These primitive minerals largely crystallised in the lower oceanic crust, and our preliminary data for lower crustal rocks and minerals shows that they preserve a remarkable range of isotope compositions. Taken together, these results indicate that the upper mantle sampled by MORB is extremely heterogeneous, reflecting depletion and enrichment over much of Earth's geological history.

Structure and Properties of Melt-spun Bio-based Polyamide/Eu(TTA)3Phen Composite fibers

NASA Astrophysics Data System (ADS)

Li, Yunye; Lou, Pengfei; Jia, Qingxiu

2018-02-01

In this paper, the bio-based polyamide (PA ) was melt polymerized from four bio-based monomers. Composites of the bio-based PA and europium complex Eu(TTA)3Phen were prepared through solution mixing using N, N-Dimethylformamide (DMF) and formic acid as the mixed solvent, and then composite fibers were obtained by melt spinning method. The structure and properties of the melt-spun composite fibers were characterized by FTIR and SEM. The results indicated that the Eu(TTA)3Phen complex, with the average diameter below 300 nm, was homogeneously dispersed in the PA matrix. FTIR spectra indicated that the coordination bond between carbonyl of BDIS and Eu(TTA)3Phen complex formed, which was also confirmed by the mechanical properties. The initial modulus and breaking strength of these fibers can arrived at 2.5GPa and 0.3GPa, respectively.

Thermal and chemical evolution in the early Solar System as recorded by FUN CAIs: Part II - Laboratory evaporation of potential CMS-1 precursor material

NASA Astrophysics Data System (ADS)

Mendybaev, Ruslan A.; Williams, Curtis D.; Spicuzza, Michael J.; Richter, Frank M.; Valley, John W.; Fedkin, Alexei V.; Wadhwa, Meenakshi

2017-03-01

We present the results of laboratory experiments in which a forsterite-rich melt estimated to be a potential precursor of Allende CMS-1 FUN CAI was evaporated into vacuum for different lengths of time at 1900 °C. The evaporation of this melt resulted in residues that define trajectories in chemical as well as magnesium, silicon and oxygen isotopic composition space and come very close to the measured properties of CMS-1. The isotopic composition of the evaporation residues was also used to determine the kinetic isotopic fractionation factors [α2,1 (vapor-melt) defined as the ratio of isotopes 2 and 1 of a given element in the evaporating gas divided by their ratio in the evaporating source] for evaporation of magnesium (α25,24 for 25Mg/24Mg), silicon (α29,28 for 29Si/28Si) and oxygen (α18,16 for 18O/16O) from the forsterite-rich melt at 1900 °C. The values of α25,24 = 0.98383 ± 0.00033 and α29,28 = 0.99010 ± 0.00038 are essentially independent of change in the melt composition as evaporation proceeds. In contrast, α18,16 changes from 0.9815 ± 0.0016 to ∼0.9911 when the residual melt composition changes from forsteritic to melilitic. Using the determined values of α25,24 and α29,28 and present-day bulk chemical composition of the CMS-1, the composition of the precursor of the inclusion was estimated to be close to the clinopyroxene + spinel + forsterite assemblage condensed from a solar composition gas. The correspondence between the chemical composition and isotopic fractionation of experimental evaporation residues and the present-day bulk chemical and isotopic compositions of CMS-1 is evidence that evaporation played a major role in the chemical evolution of CMS-1.

Nonlinear system identification of the reduction nickel oxide smelting process in electric arc furnace

NASA Astrophysics Data System (ADS)

Gubin, V.; Firsov, A.

2018-03-01

As the title implies the article describes the nonlinear system identification of the reduction smelting process of nickel oxide in electric arc furnaces. It is suggested that for operational control ratio of components of the charge must be solved the problem of determining the qualitative composition of the melt in real time. The use of 0th harmonic of phase voltage AC furnace as an indirect measure of the melt composition is proposed. Brief description of the mechanism of occurrence and nature of the non-zero 0th harmonic of the AC voltage of the arc is given. It is shown that value of 0th harmonic of the arc voltage is not function of electrical parameters but depends of the material composition of the melt. Processed industrial data are given. Hammerstein-Wiener model is used for description of the dependence of 0th harmonic of the furnace voltage from the technical parameters of melting furnace: the melt composition and current. Recommendations are given about the practical use of the model.

Experimental correlation of melt structures, nucleation rates, and thermal histories of silicate melts

NASA Technical Reports Server (NTRS)

Boynton, W. V.; DRAKE; HILDEBRAND; JONES; LEWIS; TREIMAN; WARK

1987-01-01

The theory and measurement of the structure of liquids is an important aspect of modern metallurgy and igneous petrology. Liquid structure exerts strong controls on both the types of crystals that may precipitate from melts and on the chemical composition of those crystals. An interesting aspect of melt structure studies is the problem of melt memories; that is, a melt can retain a memory of previous thermal history. This memory can influence both nucleation behavior and crystal composition. This melt memory may be characterized quantitatively with techniques such as Raman, infrared and NMR spectroscopy to provide information on short-range structure. Melt structure studies at high temperature will take advantage of the microgravity conditions of the Space Station to perform containerless experiments. Melt structure determinations at high temperature (experiments that are greatly facilitated by containerless technology) will provide invaluable information for materials science, glass technology, and geochemistry. In conjunction with studies of nucleation behavior and nucleation rates, information relevant to nucleation in magma chambers in terrestrial planets will be acquired.

Investigating Planetesimal Evolution by Experiments with Fe-Ni Metallic Melts: Light Element Composition Effects on Trace Element Partitioning Behavior

NASA Astrophysics Data System (ADS)

Chabot, N. L.

2017-12-01

As planetesimals were heated up in the early Solar System, the formation of Fe-Ni metallic melts was a common occurrence. During planetesimal differentiation, the denser Fe-Ni metallic melts separated from the less dense silicate components, though some meteorites suggest that their parent bodies only experienced partial differentiation. If the Fe-Ni metallic melts did form a central metallic core, the core eventually crystallized to a solid, some of which we sample as iron meteorites. In all of these planetesimal evolution processes, the composition of the Fe-Ni metallic melt influenced the process and the resulting trace element chemical signatures. In particular, the metallic melt's "light element" composition, those elements present in the metallic melt in a significant concentration but with lower atomic masses than Fe, can strongly affect trace element partitioning. Experimental studies have provided critical data to determine the effects of light elements in Fe-Ni metallic melts on trace element partitioning behavior. Here I focus on combining numerous experimental results to identify trace elements that provide unique insight into constraining the light element composition of early Solar System Fe-Ni metallic melts. Experimental studies have been conducted at 1 atm in a variety of Fe-Ni systems to investigate the effects of light elements on trace element partitioning behavior. A frequent experimental examination of the effects of light elements in metallic systems involves producing run products with coexisting solid metal and liquid metal phases. Such solid-metal-liquid-metal experiments have been conducted in the Fe-Ni binary system as well as Fe-Ni systems with S, P, and C. Experiments with O-bearing or Si-bearing Fe-Ni metallic melts do not lend themselves to experiments with coexisting solid metal and liquid metal phases, due to the phase diagrams of these elements, but experiments with two immiscible Fe-Ni metallic melts have provided insight into the qualitative effects of O and Si relative to the well-determined effects of S. Together, these experimental studies provide a robust dataset to identify key elements that are predicted to produce distinct chemical signatures as a function of different Fe-Ni metallic melt compositions during planetesimal evolution processes.

Compositions of Magmatic and Impact Melt Sulfides in Tissint And EETA79001: Precursors of Immiscible Sulfide Melt Blebs in Shergottite Impact Melts

NASA Technical Reports Server (NTRS)

Ross, D. K.; Rao, M. N.; Nyquist, L.; Agee, C.; Sutton, S.

2013-01-01

Immiscible sulfide melt spherules are locally very abundant in shergottite impact melts. These melts can also contain samples of Martian atmospheric gases [1], and cosmogenic nuclides [2] that are present in impact melt, but not in the host shergottite, indicating some components in the melt resided at the Martian surface. These observations show that some regolith components are, at least locally, present in the impact melts. This view also suggests that one source of the over-abundant sulfur in these impact melts could be sulfates that are major constituents of Martian regolith, and that the sulfates were reduced during shock heating to sulfide. An alternative view is that sulfide spherules in impact melts are produced solely by melting the crystalline sulfide minerals (dominantly pyrrhotite, Fe(1-x)S) that are present in shergottites [3]. In this abstract we report new analyses of the compositions of sulfide immiscible melt spherules and pyrrhotite in the shergottites Tissint, and EETA79001,507, and we use these data to investigate the possible origins of the immiscible sulfide melt spherules. In particular, we use the metal/S ratios determined in these blebs as potential diagnostic criteria for tracking the source material from which the numerous sulfide blebs were generated by shock in these melts.

Valence State Partitioning of Cr and V Between Olivine-Melt and Pyroxene-Melt in Experimental Basalts of a Eucritic Composition

NASA Technical Reports Server (NTRS)

Karner, J. M.; Jones, J. H.; Le, L.

2017-01-01

The partitioning of multivalent elements in basaltic systems can elucidate the oxygen fugacity (fO2) conditions under which basalts formed on planetary bodies (Earth, Moon, Mars, asteroids). Chromium and V are minor and trace elements in basaltic melts, partition into several minerals that crystallize from basaltic melts, exist in multiple valence states at differing fO2 conditions, and can therefore be used as oxybarometers for basaltic melts. Chromium is mostly 3+ in terrestrial basaltic melts at relatively high fO2 values (= IW+3.5), and mostly 2+ in melts at low fO2 values (= IW-1), such as those on the Moon and some asteroids. At intermediate fO2s, (i.e., IW-1 to IW+3.5), basaltic melts contain both Cr3+ and Cr2+. Vanadium in basaltic melts is mostly 4+ at high fO2, mostly 3+ at low fO2, and a mix of V3+ and V4+ at intermediate fO2 con-ditions. Understanding the partitioning of Cr and V into silicate phases with changing fO2 is therefore critical to the employment of Cr and V oxybarometers. In this abstract we examine the equilibrium partitioning of Cr and V between olivine/melt and pyroxene/melt in experimental charges of a eucritic composition produced at differing fO2 conditions. This study will add to the experimental data on DCr and DV (i.e., olivine/melt, pyroxene/melt) at differing fO2, and in turn these D values will be used to assess the fO2 of eucrite basalts and perhaps other compositionally similar planetary basalts.

Zn isotopic heterogeneity in the mantle: A melting control?

NASA Astrophysics Data System (ADS)

Doucet, Luc S.; Mattielli, Nadine; Ionov, Dmitri A.; Debouge, Wendy; Golovin, Alexander V.

2016-10-01

We present new Zn elemental and isotope data on seventeen fertile and refractory mantle peridotite xenoliths. Eleven fertile peridotites are garnet and spinel lherzolites from Vitim and Tariat (Siberia and Mongolia) and represent some of the most pristine fertile peridotites available. Six refractory peridotites are spinel harzburgites from the Udachnaya kimberlite (Siberian craton) that are nearly pristine residues of high-degree polybaric melting at high pressure (7-4 GPa). Geochemical data suggest that Zn isotopic compositions in the peridotites have not been affected by post-melting processes such as metasomatism, contamination by the host-magmas or alteration. The fertile peridotites have uniform Zn concentrations (59 ± 2 ppm) and Zn isotopic compositions with δ66Zn (relative to JMC-Lyon-03-0749l) = +0.30 ± 0.03‰ consistent with the Bulk Silicate Earth estimates of δ66Zn = +0.28 ± 0.05‰ (Chen et al., 2013). The refractory peridotites have Zn concentrations ranging from 30 to 48 ppm and δ66Zn from + 0.10 ± 0.01 ‰ to + 0.18 ± 0.01 ‰ with an average of + 0.14 ± 0.03 ‰. Our data suggest that the lithospheric mantle has a heterogeneous Zn isotopic composition. Modeling of Zn isotope partitioning during partial melting of fertile mantle suggests that high degrees of melt extraction (>30%) may significantly fractionate Zn isotopes (up to 0.16‰) and that during mantle melting, Zn concentrations and isotopic compositions are mainly controlled by the stability of clinopyroxene and garnet within the melting residue. Because the stability of clinopyroxene and garnet is mainly pressure dependent we suggest that both the depth and the degrees of melt extraction may control Zn isotope fractionation during mantle melting.

Tholeiitic basalt magmatism of Kilauea and Mauna Loa volcanoes of Hawaii

USGS Publications Warehouse

Murata, K.J.

1970-01-01

The primitive magmas of Kilauca and Mauna Loa are generated by partial melting of mantle peridotite at depths of -60 km or more. Results of high-pressure melting experiments indicate that the primitive melt must contain at least 20% MgO in order to have olivine as a liquidus mineral. The least fractionated lavas of both volcanoes have olivine (Fa13) on the liquidus at 1 atmosphere, suggesting that the only substance lost from the primitive melt, during a rather rapid ascent to the surface, is olivine. This relation allows the primitive composition to be computed by adding olivine to the composition of an erupted lava until total MgO is at least 20 percent. Although roughly similar, historic lavas of the two volcanoes show a consistent difference in composition. The primitive melt of Mauna Loa contains 20% more dissolved orthopyroxene, a high-temperature melting phase in the mantle, and is deficient in elements such as potassium, uranium, and niobium, which presumably occur in minor low-melting phases. Mauna Loa appears to be the older volcano, deriving its magma at higher temperature and greater depth from a more depleted source rock. ?? 1970 Springer-Verlag.

The Effect of the Melt Viscosity and Impregnation of a Film on the Mechanical Properties of Thermoplastic Composites

PubMed Central

Kim, Jong Won; Lee, Joon Seok

2016-01-01

Generally, to produce film-type thermoplastic composites with good mechanical properties, high-performance reinforcement films are used. In this case, films used as a matrix are difficult to impregnate into tow due to their high melt viscosity and high molecular weight. To solve the problem, in this paper, three polypropylene (PP) films with different melt viscosities were used separately to produce film-type thermoplastic composites. A film with a low melt viscosity was stacked so that tow was impregnated first and a film with a higher melt viscosity was then stacked to produce the composite. Four different composites were produced by regulating the pressure rising time. The thickness, density, fiber volume fraction (Vf), and void content (Vc) were analyzed to identify the physical properties and compare them in terms of film stacking types. The thermal properties were identified by using differential scanning calorimetry (DSC) and dynamical mechanical thermal analysis (DMTA). The tensile property, flexural property, interlaminar shear strength (ILSS), and scanning electron microscopy (SEM) were performed to identify the mechanical properties. For the films with low molecular weight, impregnation could be completed fast but showed low strength. Additionally, the films with high molecular weight completed impregnation slowly but showed high strength. Therefore, appropriate films should be used considering the forming process time and their mechanical properties to produce film-type composites. PMID:28773572

Oxygen production by electrolysis of molten lunar regolith

NASA Technical Reports Server (NTRS)

Haskin, Larry A.

1990-01-01

The goal of this study was threefold. First, the theoretical energy requirements of the process were to be defined. This includes studies of the relevant oxidation-reduction reactions in the melt, their kinetics and energies of reaction, and experimental determination of production efficiencies and melt resistivities as functions of melt composition and applied potential. Second, the product(s) of silicate electrolysis were to be characterized. This includes: (1) evaluating the phase relationships in the systems SiO2-TiO2-Al2O3-MgO-FeO-CaO and Fe-Si; (2) estimating the compositions of the metal products as a function of applied potential and feedstock composition based on phase equilibria in the Fe-Si system and free energy values for SiO2 and FeO reported in the literature; (3) definition of compositions of products in actual experiments; and (4) definition of the form the product takes (whether phases separate or remain fixed, whether crystals settle or float in the remaining melt, and how large crystals form). Third, materials for these highly corrosive high-temperature silicate melts were to be identified. This includes identifing materials that may be either inert or thermodynamically stable in these melts, and experimental testing of the materials to confirm that they do not deteriorate. The results are discussed within this framework.

Buoyancy-driven melt segregation in the earth's moon. I - Numerical results

NASA Technical Reports Server (NTRS)

Delano, J. W.

1990-01-01

The densities of lunar mare magmas have been estimated at liquidus temperatures for pressures from 0 to 47 kbar (0.4 GPa; center of the moon) using a third-order Birch-Murnaghan equation and compositionally dependent parameters from Large and Carmichael (1987). Results on primary magmatic compositions represented by pristine volcanic glasses suggest that the density contrast between very-high-Ti melts and their liquidus olivines may approach zero at pressures of about 25 kbar (2.5 GPa). Since this is the pressure regime of the mantle source regions for these magmas, a compositional limit of eruptability for mare liquids may exist that is similar to the highest Ti melt yet observed among the lunar samples. Although the moon may have generated magmas having greater than 16.4 wt pct TiO2, those melts would probably not have reached the lunar surface due to their high densities, and may have even sunk deeper into the moon's interior as negatively buoyant diapirs. This process may have been important for assimilative interactions in the lunar mantle. The phenomenon of melt/solid density crossover may therefore occur not only in large terrestrial-type objects but also in small objects where, despite low pressures, the range of melt compositions is extreme.

Quantitative Model to Predict Melts on the Ol-Opx Saturation Boundary during Mantle Melting: The Role of H2O

NASA Astrophysics Data System (ADS)

Andrews, A. L.; Grove, T. L.

2014-12-01

Two quantitative, empirical models are presented that predict mantle melt compositions in equilibrium with olivine (ol) + orthopyroxene (opx) ± spinel (sp) as a function of variable pressure and H2O content. The models consist of multiple linear regressions calibrated using new data from H2O-undersaturated primitive and depleted mantle lherzolite melting experiments as well as experimental literature data. The models investigate the roles of H2O, Pressure, 1-Mg# (1-[XMg/(XMg+XFe)]), NaK# ((Na2O+K2O)/(Na2O+K2O+CaO)), TiO2, and Cr2O3 on mantle melt compositions. Melts are represented by the pseudoternary endmembers Clinopyroxene (Cpx), Olivine (Ol), Plagioclase (Plag), and Quartz (Qz) of Tormey et al. (1987). Model A returns predictive equations for the four endmembers with identical predictor variables, whereas Model B chooses predictor variables for the four compositional endmember equations and temperature independently. We employ the use of Akaike Information Criteria (Akaike, 1974) to determine the best predictor variables from initial variables chosen through thermodynamic reasoning and by previous models. In both Models A and B, the coefficients for H2O show that increasing H2O drives the melt to more Qz normative space, as the Qz component increases by +0.012(3) per 1 wt.% H2O. The other endmember components decrease and are all three times less affected by H2O (Ol: -0.004(2); Cpx: -0.004(2); Plag: -0.004(3)). Consistent with previous models and experimental data, increasing pressure moves melt compositions to more Ol normative space at the expense of the Qz component. The models presented quantitatively determine the influence of H2O, Pressure, 1-Mg#, NaK#, TiO2, and Cr2O3 on mantle melts in equilibrium with ol+opx±sp; the equations presented can be used to predict melts of known mantle source compositions saturated in ol+opx±sp. References Tormey, Grove, & Bryan (1987), doi: 10.1007/BF00375227. Akaike (1974), doi: 10.1109/TAC.1974.1100705.

Phase behavior and reactive transport of partial melt in heterogeneous mantle model

NASA Astrophysics Data System (ADS)

Jordan, J.; Hesse, M. A.

2013-12-01

The reactive transport of partial melt is the key process that leads to the chemical and physical differentiation of terrestrial planets and smaller celestial bodies. The essential role of the lithological heterogeneities during partial melting of the mantle is increasingly recognized. How far can enriched melts propagate while interacting with the ambient mantle? Can the melt flow emanating from a fertile heterogeneity be localized through a reactive infiltration feedback in a model without exogenous factors or contrived initial conditions? A full understanding of the role of heterogeneities requires reactive melt transport models that account for the phase behavior of major elements. Previous work on reactive transport in the mantle focuses on trace element partitioning; we present the first nonlinear chromatographic analysis of reactive melt transport in systems with binary solid solution. Our analysis shows that reactive melt transport in systems with binary solid solution leads to the formation of two separate reaction fronts: a slow melting/freezing front along which enthalpy change is dominant and a fast dissolution/precipitation front along which compositional changes are dominated by an ion-exchange process over enthalpy change. An intermediate state forms between these two fronts with a bulk-rock composition and enthalpy that are not necessarily bounded by the bulk-rock composition and enthalpy of either the enriched heterogeneity or the depleted ambient mantle. The formation of this intermediate state makes it difficult to anticipate the porosity changes and hence the stability of reaction fronts. Therefore, we develop a graphical representation for the solution that allows identification of the intermediate state by inspection, for all possible bulk-rock compositions and enthalpies of the heterogeneity and the ambient mantle. We apply the analysis to the partial melting of an enriched heterogeneity. This leads to the formation of moving precipitation front that followes a stationary melting front which creates low porosity intermediate states. Therefore, localization of the melt flow is not observed because the precipitation front is stable and the melting front is always stationary under these conditions. This analysis illustrates the counterintuitive behavior that can arise when the phase behavior is taken into account and is a first step to understanding reactive melt transport and the reactive constraints on channelization in partial melts. ¬¬

Study of rheological properties of polypropylene/organoclay hybrid materials.

PubMed

Yu, Suzhu; Liu, Songlin; Zhao, Jianhong; Yong, Ming Shyan

2006-12-01

Polypropylene nanocomposites reinforced with organic modified montmorillonite clay have been fabricated by melt compounding using extrusion. The morphology of the composites is studied with transmission electron microscopy and X-ray diffraction. The melt-state rheological properties of the nanocomposites have been investigated as a function of temperature and organoclay loading. It is found that the organoclays are intercalated and dispersed evenly in the matrix. The storage and loss moduli of the hybrid composites decrease with temperature and increase with organoclay concentration. Both polypropylene and its composites demonstrate a melt-like rheological behavior, indicating the low degree of exfoliation of the organoclay. A shear thinning behavior is found for both polypropylene and its composites, but the onset of shear thinning for organoclay composites occurs at lower shear rates.

Melt-Infiltration Process For SiC Ceramics And Composites

NASA Technical Reports Server (NTRS)

Behrendt, Donald R.; Singh, Mrityunjay

1994-01-01

Reactive melt infiltration produces silicon carbide-based ceramics and composites faster and more economically than do such processes as chemical vapor infiltration (CVI), reaction sintering, pressureless sintering, hot pressing, and hot isostatic pressing. Process yields dense, strong materials at relatively low cost. Silicon carbide ceramics and composites made by reactive melt infiltration used in combustor liners of jet engines and in nose cones and leading edges of high-speed aircraft and returning spacecraft. In energy industry, materials used in radiant-heater tubes, heat exchangers, heat recuperators, and turbine parts. Materials also well suited to demands of advanced automobile engines.

Experimental determination of CO2 content at graphite saturation along a natural basalt-peridotite melt join: Implications for the fate of carbon in terrestrial magma oceans

NASA Astrophysics Data System (ADS)

Duncan, Megan S.; Dasgupta, Rajdeep; Tsuno, Kyusei

2017-05-01

Knowledge of the carbon carrying capacity of peridotite melt at reducing conditions is critical to constrain the mantle budget and planet-scale distribution of carbon set at early stage of differentiation. Yet, neither measurements of CO2 content in reduced peridotite melt nor a reliable model to extrapolate the known solubility of CO2 in basaltic (mafic) melt to solubility in peridotitic (ultramafic) melt exist. There are several reasons for this gap; one reason is due to the unknown relative contributions of individual network modifying cations, such as Ca2+ versus Mg2+, on carbonate dissolution particularly at reducing conditions. Here we conducted high pressure, temperature experiments to estimate the CO2 contents in silicate melts at graphite saturation over a compositional range from natural basalts toward peridotite at a fixed pressure (P) of 1.0 GPa, temperature (T) of 1600 °C, and oxygen fugacity (log ⁡ fO2 ∼ IW + 1.6). We also conducted experiments to determine the relative effects of variable Ca and Mg contents in mafic compositions on the dissolution of carbonate. Carbon in quenched glasses was measured and characterized using Fourier transform infrared spectroscopy (FTIR) and Raman Spectroscopy and was found to be dissolved as carbonate (CO32-). The FTIR spectra showed CO32- doublets that shifted systematically with the MgO and CaO content of silicate melts. Using our data and previous work we constructed a new composition-based model to determine the CO2 content of ultramafic (peridotitic) melt representative of an early Earth, magma ocean composition at graphite saturation. Our data and model suggest that the dissolved CO2 content of reduced, peridotite melt is significantly higher than that of basaltic melt at shallow magma ocean conditions; however, the difference in C content between the basaltic and peridotitic melts may diminish with depth as the more depolymerized peridotite melt is more compressible. Using our model of CO2 content at graphite saturation as a function of P-T-fO2-melt composition, we predict that a superliquidus shallow magma ocean should degas CO2. Whereas if the increase of fO2 with depth is weak, a magma ocean may ingas a modest amount of carbon during crystallization. Further, using the carbon content of peridotite melt at log ⁡ fO2 of IW and the knowledge of C content of Fe-rich alloy melt, we also consider the core-mantle partitioning of carbon, showing that DCmetal/peridotite of a shallow magma ocean is generally higher than previously estimated.

Generation of Silicic Melts in the Early Izu-Bonin Arc Recorded by Detrital Zircons in Proximal Arc Volcaniclastic Rocks From the Philippine Sea

NASA Astrophysics Data System (ADS)

Barth, A. P.; Tani, K.; Meffre, S.; Wooden, J. L.; Coble, M. A.; Arculus, R. J.; Ishizuka, O.; Shukle, J. T.

2017-10-01

A 1.2 km thick Paleogene volcaniclastic section at International Ocean Discovery Program Site 351-U1438 preserves the deep-marine, proximal record of Izu-Bonin oceanic arc initiation, and volcano evolution along the Kyushu-Palau Ridge (KPR). Pb/U ages and trace element compositions of zircons recovered from volcaniclastic sandstones preserve a remarkable temporal record of juvenile island arc evolution. Pb/U ages ranging from 43 to 27 Ma are compatible with provenance in one or more active arc edifices of the northern KPR. The abundances of selected trace elements with high concentrations provide insight into the genesis of U1438 detrital zircon host melts, and represent useful indicators of both short and long-term variations in melt compositions in arc settings. The Site U1438 zircons span the compositional range between zircons from mid-ocean ridge gabbros and zircons from relatively enriched continental arcs, as predicted for melts in a primitive oceanic arc setting derived from a highly depleted mantle source. Melt zircon saturation temperatures and Ti-in-zircon thermometry suggest a provenance in relatively cool and silicic melts that evolved toward more Th and U-rich compositions with time. Th, U, and light rare earth element enrichments beginning about 35 Ma are consistent with detrital zircons recording development of regional arc asymmetry and selective trace element-enriched rear arc silicic melts as the juvenile Izu-Bonin arc evolved.

Using the South Pole-Aitken (SPA) Impact Melt Composition to Infer Upper Mantle Mineralogy and Timing of Potential Mantle Overturn

NASA Astrophysics Data System (ADS)

Kring, D. A.; Needham, D. H.

2018-05-01

Observed melt composition within the SPA basin are consistent with an impact prior to mantle overturn, when the upper mantle contained clinopyroxene rather than olivine. Potentially, the impact triggered mantle overturn.

Origin and evolution of primitive melts from the Debunscha Maar, Cameroon: Consequences for mantle source heterogeneity within the Cameroon Volcanic Line

NASA Astrophysics Data System (ADS)

Ngwa, Caroline N.; Hansteen, Thor H.; Devey, Colin W.; van der Zwan, Froukje M.; Suh, Cheo E.

2017-09-01

Debunscha Maar is a monogenetic volcano forming part of the Mt. Cameroon volcanic field, located within the Cameroon Volcanic Line (CVL). Partly glassy cauliflower bombs have primitive basanite-picrobasalt compositions and contain abundant normally and reversely zoned olivine (Fo 77-87) and clinopyroxene phenocrysts. Naturally quenched melt inclusions in the most primitive olivine phenocrysts show compositions which, when corrected for post-entrapment modification, cover a wide range from basanite to alkali basalt (MgO 6.9-11.7 wt%), and are generally more primitive than the matrix glasses (MgO 5.0-5.5 wt%) and only partly fall on a common liquid line of descent with the bulk rock samples and matrix glasses. Melt inclusion trace element compositions lie on two distinct geochemical trends: one (towards high Ba/Nb) is thought to represent the effect of various proportions of anhydrous lherzolite and amphibole-bearing peridotite in the source, while the other (for example, high La/Y) reflects variable degrees of partial melting. Comparatively low fractionation-corrected CaO in the melt inclusions with the highest La/Y suggests minor involvement of a pyroxenite source component that is only visible at low degrees of melting. Most of the samples show elevated Gd/Yb, indicating up to 8% garnet in the source. The range of major and trace elements represented by the melt inclusions covers the complete geochemical range given by basalts from different volcanoes of the Cameroon volcanic line, indicating that geochemical signatures that were previously thought to be volcano-specific in fact are probably present under all volcanoes. Clinopyroxene-melt barometry strongly indicates repeated mixing of compositionally diverse melts within the upper mantle at 830 ± 170 MPa prior to eruption. Mantle potential temperatures estimated for the primitive melt inclusions suggest that the thermal influence of a mantle plume is not required to explain the magma petrogenesis.

Apatite-Melt Partitioning at 1 Bar: An Assessment of Apatite-Melt Exchange Equilibria Resulting from Non-Ideal Mixing of F and Cl in Apatite

NASA Technical Reports Server (NTRS)

McCubbin, F. M.; Ustunisik, G.; Vander Kaaden, K. E.

2016-01-01

The mineral apatite [Ca5(PO4)3(F,Cl,OH)] is present in a wide range of planetary materials. Due to the presence of volatiles within its crystal structure (X-site), many recent studies have attempted to use apatite to constrain the volatile contents of planetary magmas and mantle sources. In order to use the volatile contents of apatite to precisely determine the abundances of volatiles in coexisting silicate melt or fluids, thermodynamic models for the apatite solid solution and for the apatite components in multi-component silicate melts and fluids are required. Although some thermodynamic models for apatite have been developed, they are incomplete. Furthermore, no mixing model is available for all of the apatite components in silicate melts or fluids, especially for F and Cl components. Several experimental studies have investigated the apatite-melt and apatite-fluid partitioning behavior of F, Cl, and OH in terrestrial and planetary systems, which have determined that apatite-melt partitioning of volatiles are best described as exchange equilibria similar to Fe-Mg partitioning between olivine and silicate melt. However, McCubbin et al. recently reported that the exchange coefficients may vary in portions of apatite compositional space where F, Cl, and OH do not mix ideally in apatite. In particular, solution calorimetry data of apatite compositions along the F-Cl join exhibit substantial excess enthalpies of mixing. In the present study, we conducted apatite-melt partitioning experiments in evacuated, sealed silica-glass tubes at approximately 1 bar and 950-1050 degrees Centigrade on a synthetic Martian basalt composition equivalent to the basaltic shergottite Queen Alexandria Range (QUE) 94201. These experiments were conducted dry, at low pressure, to assess the effects of temperature and apatite composition on the partitioning behavior of F and Cl between apatite and basaltic melt along the F-Cl apatite binary join, where there is non-ideal mixing of F and Cl in apatite.

Electrical Conductivity of Molten DyCl3-NaCl and DyCl3-KCl Systems: An Approach to Structural Interpretations of Rare Earth Chloride Melts

NASA Astrophysics Data System (ADS)

Iwadate, Yasuhiko; Ohkubo, Takahiro

2017-11-01

Electrical conductivities (κs) of molten DyCl3-NaCl and DyCl3-KCl systems were estimated by measuring the impedances of each mixture melt at any temperature and/or frequency. The molar volumes (Vms) were measured by dilatometry and represented as a polynomial empirical equation of temperature and composition. Due to both the properties, the molar conductivities (Λms) were calculated and their temperature and/or composition dependences were discussed from the standpoint of structural features as well. The κs increased curvilinearly with increasing temperature across the whole composition ranges. This trend was also applied to the Λms which was fitted by an Arrhenius-type equation. The relationship of Λms with melt composition was studied and the Λms were found to decrease with increasing composition of DyCl3. These findings were interpreted based on the results of structural science so far reported, and finally, the relationship between Λms and the structures of pure rare earth chloride melts was discussed.

Silica-enriched mantle sources of subalkaline picrite-boninite-andesite island arc magmas

NASA Astrophysics Data System (ADS)

Bénard, A.; Arculus, R. J.; Nebel, O.; Ionov, D. A.; McAlpine, S. R. B.

2017-02-01

Primary arc melts may form through fluxed or adiabatic decompression melting in the mantle wedge, or via a combination of both processes. Major limitations to our understanding of the formation of primary arc melts stem from the fact that most arc lavas are aggregated blends of individual magma batches, further modified by differentiation processes in the sub-arc mantle lithosphere and overlying crust. Primary melt generation is thus masked by these types of second-stage processes. Magma-hosted peridotites sampled as xenoliths in subduction zone magmas are possible remnants of sub-arc mantle and magma generation processes, but are rarely sampled in active arcs. Published studies have emphasised the predominantly harzburgitic lithologies with particularly high modal orthopyroxene in these xenoliths; the former characteristic reflects the refractory nature of these materials consequent to extensive melt depletion of a lherzolitic protolith whereas the latter feature requires additional explanation. Here we present major and minor element data for pristine, mantle-derived, lava-hosted spinel-bearing harzburgite and dunite xenoliths and associated primitive melts from the active Kamchatka and Bismarck arcs. We show that these peridotite suites, and other mantle xenoliths sampled in circum-Pacific arcs, are a distinctive peridotite type not found in other tectonic settings, and are melting residues from hydrous melting of silica-enriched mantle sources. We explore the ability of experimental studies allied with mantle melting parameterisations (pMELTS, Petrolog3) to reproduce the compositions of these arc peridotites, and present a protolith ('hybrid mantle wedge') composition that satisfies the available constraints. The composition of peridotite xenoliths recovered from erupted arc magmas plausibly requires their formation initially via interaction of slab-derived components with refractory mantle prior to or during the formation of primary arc melts. The liquid compositions extracted from these hybrid sources are higher in normative quartz and hypersthene (i.e., they have a more silica-saturated character) in comparison with basalts derived from prior melt-depleted asthenospheric mantle beneath ridges. These primary arc melts range from silica-rich picrite to boninite and high-Mg basaltic andesite along a residual spinel harzburgite cotectic. Silica enrichment in the mantle sources of arc-related, subalkaline picrite-boninite-andesite suites coupled with the amount of water and depth of melting, are important for the formation of medium-Fe ('calc-alkaline') andesite-dacite-rhyolite suites, key lithologies forming the continental crust.

Ferrobasalt-rhyolite immiscibility in tholeiitic volcanic and plutonic series (Invited)

NASA Astrophysics Data System (ADS)

Charlier, B.; Namur, O.; Kamenetsky, V. S.; Grove, T. L.

2013-12-01

One atmosphere experiments show that silicate liquid immiscibility develops between Fe-rich and Si-rich melts below 1000-1020°C in compositionally diverse lavas that represent classical tholeiitic trends, such as Mull, Iceland, Snake River Plain and Sept Iles. Extreme iron enrichment along the evolution trend is not necessary; immiscibility also develops during iron depletion and silica enrichment after Fe-Ti oxide saturation. Natural liquid lines of descent for major tholeiitic series also approach or intersect the experimentally-defined compositional space of immiscibility. The importance of ferrobasalt-rhyolite unmixing in both volcanic and plutonic environments is supported by worldwide occurrence of immiscible globules in the mesostasis of erupted basalts, and by unmixed melt inclusions in cumulus phases of major layered intrusions such as Sept Iles, Skaergaard and Sudbury. A clear case of liquid immiscibility is also recorded in intrusive tholeiitic gabbros from the Siberian Large Igneous Province and is evidenced by textures and compositions of millimeter-sized silicate melt pools trapped in native iron. An important implication of immiscibility in natural ferrobasaltic provinces is the development of a compositional gap characterized by the absence of intermediate compositions, a major feature observed in many tholeiitic provinces and referred to as the Daly gap. The compositions of experimental silica-rich immiscible melts coincide with those of natural rhyolites with high FeOtot and low Al2O3, which suggests a potential role for large-scale immiscibility in the petrogenesis of late-stage ferroan silicic melts. No evidence for the paired ferrobasaltic melt is observed in volcanic provinces, probably because of its uneruptable characteristics. Instead, Fe-Ti×P-rich gabbros crystallized at depth and are the cumulate products of immiscible Fe-rich melts in plutonic settings, a feature clearly evidenced in the Sept Iles intrusion. The production of immiscible Fe-Ti-Ca-P liquids has also important implications for the formation of some iron deposits associated with alkaline lavas.

Geophysical constraints on the compensation mechanism of the Galápagos swell

NASA Astrophysics Data System (ADS)

Canales, J.; Ito, G.; Detrick, R. S.; Sinton, J. M.

2001-12-01

We use geophysical observations such as bathymetry, gravity, and seismic crustal thickness to understand the origin of the Galápagos swell. Wide-angle refraction and multichannel reflection seismic data show that the crust along the Galápagos Spreading Center (GSC) between 97.5° W and 91° W thickens by 2.3 km as the Galápagos plume is approached from the west [Ito et al., this meeting]. Axial depth along the GSC shoals by 1800 m, 60% of which is due to dynamic topography and changes in axial morphology. The remaining 700 m correspond to the amplitude of the Galápagos bathymetric swell, 75% of which is explained by crustal thickening. The eastward shoaling of the swell and increase in crustal thickness along the GSC is accompained by a progressive decrease in mantle Bouguer gravity anomaly (MBA). Assuming a constant crustal thickness model, the MBA reaches a minimum value of -70 mGal near 91.25° W. After correcting for changes in crustal thickness, however, the gravity anomaly shows a minimum of -25 mGal near 92.2° W, the area where the GSC is intersected by the Wolf-Darwin volcanic lineament. We attribute the remaining 25% of swell bathymetry and 35% of gravity anomaly to an eastward reduction of mantle density above an effective compensation depth, constrained to be 50-200 km. Simple melting calculations assuming passive mantle upwelling predict that the observed crustal thickenning is consistent with a small eastward increase in mantle temperature of 15-25 ° C. This thermal anomaly produces an eastward decrease in mantle density due to thermal expansion and the subsequent along-axis variation in melt depletion. For preferred mantle compensation depths of 50-150 km the thermal effects can explain 40 to 70% of the mantle density anomaly required by the geophysical observations. Therefore, our results require the existence of compositionally-buoyant mantle beneath the GCS near the Galápagos plume. We will discuss plausible origins for the mantle anomaly such as depleted mantle by the upwelling plume, melt retention, or a mantle source enriched in incompatible elements and volatiles [Cushman et al., this meeting], and their implications for melting beneath the Galápagos plume-ridge system.

Compositional dependent partial molar volume and compressibility of CO2 in rhyolite, phonolite and basalt glasses

NASA Astrophysics Data System (ADS)

Lerch, P.; Seifert, R.; Malfait, W. J.; Sanchez-Valle, C.

2012-12-01

Carbon dioxide is the second most abundant volatile in magmatic systems and plays an important role in many magmatic processes, e.g. partial melting, volatile saturation, outgassing. Despite this relevance, the volumetric properties of carbon-bearing silicates at relevant pressure and temperature conditions remain largely unknown because of considerable experimental difficulties associated with in situ measurements. Density and elasticity measurements on quenched glasses can provide an alternative source of information. For dissolved water, such measurements indicate that the partial molar volume is independent of compositions at ambient pressure [1], but the partial molar compressibility is not [2, 3]. Thus the partial molar volume of water may depend on melt composition at elevated pressure. For dissolved CO2, no such data is available. In order to constrain the effect of magma composition on the partial molar volume and compressibility of dissolved carbon, we determined the density and elasticity for three series of carbon-bearing basalt, phonolite and rhyolite glasses, quenched from 3.5 GPa and relaxed at ambient pressure. The CO2 content varies between 0 to 3.90 wt% depending on the glass composition. Glass densities were determined using the sink/float method in a diiodomethane (CH2I2) - acetone mixture. Brillouin measurements were conducted on relaxed and unrelaxed silicate glasses in platelet geometry to determine the compressional (VP) and shear (VS) wave velocities and elastic moduli. The partial molar volume of CO2 in rhyolite, phonolite and basalt glasses is 25.4 ± 0.9, 22.1 ± 0.6 and 26.6 ±1.8 cm3/mol, respectively. Thus, unlike for dissolved water, the partial molar volume of CO2 displays a resolvable compositional effect. Although the composition and CO2/carbonate speciation of the phonolite glasses is intermediate between that of the rhyolite and basalt glasses, the molar volume is not. Similar to dissolved water, the partial molar bulk modulus of CO2 displays a strong compositional effect. If these compositional dependencies persist in the analogue melts, the partial molar volume of dissolved CO2 will depend on melt composition, both at low and elevated pressure. Thus, for CO2-bearing melts, a full quantitative understanding of density dependent magmatic processes, such as crystal fractionation, magma mixing and melt extraction will require in situ measurements for a range of melt compositions. [1] Richet, P. et al., 2000, Contrib Mineral Petrol, 138, 337-347. [2] Malfait et al. 2011, Am. Mineral. 96, 1402-1409. [3] Whittington et al., 2012, Am. Mineral. 97, 455-467.

Degassing-induced crystallization in silicate melt inclusion: evaluating the role of post-entrapment changes in melt inclusion from the SW volcanic flows of Deccan Large Igneous Province (Deccan LIP) lava.

NASA Astrophysics Data System (ADS)

Rani Choudhary, Babita

2017-04-01

Melt inclusions represent sampling of magma during their growth in magma chambers and during ascent to the surface. Several studies of melt inclusions in Large Igneous Provinces (LIPs) in different parts of the world have been documented in the literature (Sobolev et al. 2011; Kamenetsky et al. 2012). Melt inclusions study from Deccan LIP can provide new insights into the physio-chemical conditions and evolution of this important LIP. The Deccan LIP was fissure eruption mainly emplaced over a very short duration at 66 Ma (Schoene et al. 2015). To better characterize and explain the diversity in geochemical composition, petrogenesis and volatile degassing, melt inclusions studies have been carried out in clinopyroxene and plagioclase feldspar from a suite of samples in the Western Ghats section. Samples were obtained from the upper three formations (the Wai subgroup). The inclusions are primary and range in shape and size varies from a few microns, up to 100 microns. The inclusions are crystalline, and contain daughter phases. Some are glassy, with or without a shrinkage bubble. The melt inclusions show substantial variations in major element composition. Inclusions are significantly enriched in TiO2 (3.68 to 0.08 wt%) and FeO (18.3 to 2.63 wt%). SiO2 ranges from 43.4-66.8 wt% and classification diagrams of total alkali (Na2O+K2O) Vs. silica melt inclusions show that most inclusions are of sub-alkaline to mildly alkaline composition. Al2O3 ranges from 9.7- 22.4wt % and MgO 18.3-1.6. EPMA measurements demonstrated the presence of daughter crystals, such as magnetite and titanomagnetite, and high FeO, TiO2 and CaO within melt inclusions among the silicate daughter crystal clusters. Volatiles are determined have wide range in composition in both plagioclase- and pyroxene-hosted melt inclusions by using FTIR technique, values up to 2wt% H2Ototal and 1808 ppm CO2. Moreover the variability in composition and volatiles the melt from the samples in a single flow suggests that trapped melts were significantly affected by degassing and the post-entrapment changes. After each hiatus of the magmatic pulse the differentiated residual magma was enriched in Fe-Mg-Ti. Post-entrapment crystal aggregates contribute to the alteration of the melt phase within the inclusions (Choudhary and Jadhav 2010) i.e. fractionating tholeiitic lavas follow a trend that reflected by iron saturation until Fe-Ti oxides start to precipitate. Compositional concentrations are affected by diffusion from the plagioclase host into the inclusion, e.g. precipitation of host, resulting the high Al2O3 .Therefore melt inclusions showed evolved fractionated melt with the presence of aggregated crystals indicating that formation of these Fe-Ti oxides have occurred in an aqueous condition. As well, the formation of daughter mineral assemblages (titanomagnetite, and magnetite crystallization inside the inclusions) promotes the diffusion of hydrogen out of the inclusions.

Experimental determination of carbon solubility in Fe-Ni-S melts

NASA Astrophysics Data System (ADS)

Zhang, Zhou; Hastings, Patrick; Von der Handt, Anette; Hirschmann, Marc M.

2018-03-01

To investigate the effect of metal/sulfide and Ni/Fe ratio on the C storage capacity of sulfide melts, we determine carbon solubility in Fe-Ni-S melts with various (Fe + Ni)/S and Ni/Fe via graphite-saturated high-pressure experiments from 2-7 GPa and 1200-1600 °C. Consistent with previous results, C solubility is high (4-6 wt.%) in metal-rich sulfide melts and diminishes with increasing S content. Melts with near M/S = 1 (XS > 0.4) have <0.5 wt.% C in equilibrium with graphite. C solubility is diminished modestly with increased Ni/Fe ratio, but the effect is most pronounced for S-poor melts, and becomes negligible in near-monosulfide compositions. Immiscibility between S-rich and C-rich melts is observed in Ni-poor compositions, but above ∼18 wt.% Ni there is complete miscibility. Because mantle sulfide compositions are expected to have high Ni concentrations, sulfide-carbide immiscibility is unlikely in natural mantle melts. An empirical parameterization of C solubility in Ni-Fe-S melts as a function of S and Ni contents allows estimation of the C storage capacity of sulfide in the mantle. Importantly, as the metal/sulfide (M/S) ratio of the melt increases, C storage increases both because C solubility increases and because the mass fraction of melt is enhanced by addition of metal from surrounding silicates. Under comparatively oxidized conditions where melts are near M/S = 1, as prevails at <250 km depth, bulk C storage is <3 ppm. In the deeper, more reduced mantle where M/S increases, up to 200 ppm C in typical mantle with 200 ± 100 ppm S can be stored in Fe-Ni-S melts. Thus, metal-rich sulfide melts are the principal host of carbon in the deep upper mantle and below. Residual carbon is present either as diamond or, if conditions are highly reduced and total C concentrations are low, solid alloy.

Fluoride salts as phase change materials for thermal energy storage in the temperature range 1000-1400 K

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

1988-01-01

Eutectic compositions and congruently melting intermediate compounds in binary and ternary fluoride salt systems were characterized for potential use as latent heat of fusion phase change materials to store thermal energy in the temperature range 1000-1400 K. The melting points and eutectic compositions for many systems with published phase diagrams were experimentally verified and new eutectic compositions having melting points between 1000 and 1400 K were identified. Heats of fusion of several binary and ternary eutectics and congruently melting compounds were experimentally measured by differential scanning calorimetry. For a few systems in which heats of mixing in the melts have been measured, heats of fusion of the eutectics were calculated from thermodynamic considerations and good agreement was obtained between the measured and calculated values. Several combinations of salts with high heats of fusion per unit mass (greater than 0.7 kJ/g) have been identified for possible use as phase change materials in advanced solar dynamic space power applications.

Evaporation in the young solar nebula as the origin of 'just-right' melting of chondrules

PubMed

Cohen; Hewins; Yu

2000-08-10

Chondrules are millimetre-sized, solidified melt spherules formed in the solar nebula by an early widespread heating event of uncertain nature. They were accreted into chondritic asteroids, which formed about 4.56 billion years ago and have not experienced melting or differentiation since that time. Chondrules have diverse chemical compositions, corresponding to liquidus temperatures in the range 1,350-1,800 degrees C. Most chondrules, however, show porphyritic textures (consisting of large crystals in a distinctly finer grained or glassy matrix), indicative of melting within the narrow range 0-50 degrees C below the liquidus. This suggests an unusual heating mechanism for chondrule precursors, which would raise each individual chondrule to just the right temperature (particular to individual bulk composition) in order to form porphyritic textures. Here we report the results of isothermal melting of a chondritic composition at nebular pressures. Our results suggest that evaporation stabilizes porphyritic textures over a wider range of temperatures below the liquidus (about 200 degrees C) than previously believed, thus removing the need for individual chondrule temperature buffering. In addition, we show that evaporation explains many chondrule bulk and mineral compositions that have hitherto been difficult to understand.

Evolution of the Moon's Mantle and Crust as Reflected in Trace-Element Microbeam Studies of Lunar Magmatism

NASA Astrophysics Data System (ADS)

Shearer, C. K.; Floss, C.

Ion microprobe trace-element studies of lunar cumulates [ferroan anorthosites (FAN), highlands Mg suite (HMS), and highlands alkali suite (HAS)] and volcanic glasses have provided an additional perspective in reconstructing lunar magmatism and early differentiation. Calculated melt compositions for the FANs indicate that a simple lunar magma ocean (LMO) model does not account for differences between FANs with highly magnesian mafic minerals and “typical” ferroan anorthosites. The HMS and HAS appear to have crystallized from magmas that had incompatible trace-element concentrations equal to or greater than KREEP. Partial melting of distinct, hybridized sources is consistent with these calculated melt compositions. However, the high-Mg silicates with relatively low Ni content that are observed in the HMS are suggestive of other possible processes (reduction, metal removal). The compositions of the picritic glasses indicate that they were produced by melting of hybrid cumulate sources produced by mixing of early and late LMO cumulates. The wide compositional range of near-primitive mare basalts indicates small degrees of localized melting preserved the signature of distinct mantle reservoirs. The relationship between ilmenite anomalies and 182W in the mare basalts suggests that the LMO crystallized over a short period of time.

Local melting to design strong and plastically deformable bulk metallic glass composites

PubMed Central

Qin, Yue-Sheng; Han, Xiao-Liang; Song, Kai-Kai; Tian, Yu-Hao; Peng, Chuan-Xiao; Wang, Li; Sun, Bao-An; Wang, Gang; Kaban, Ivan; Eckert, Jürgen

2017-01-01

Recently, CuZr-based bulk metallic glass (BMG) composites reinforced by the TRIP (transformation-induced plasticity) effect have been explored in attempt to accomplish an optimal of trade-off between strength and ductility. However, the design of such BMG composites with advanced mechanical properties still remains a big challenge for materials engineering. In this work, we proposed a technique of instantaneously and locally arc-melting BMG plate to artificially induce the precipitation of B2 crystals in the glassy matrix and then to tune mechanical properties. Through adjusting local melting process parameters (i.e. input powers, local melting positions, and distances between the electrode and amorphous plate), the size, volume fraction, and distribution of B2 crystals were well tailored and the corresponding formation mechanism was clearly clarified. The resultant BMG composites exhibit large compressive plasticity and high strength together with obvious work-hardening ability. This compelling approach could be of great significance for the steady development of metastable CuZr-based alloys with excellent mechanical properties. PMID:28211890

Theoretical Investigation of Calculating Temperatures in the Combining Zone of Cu/Fe Composite Plate Jointed by Explosive Welding

NASA Astrophysics Data System (ADS)

Qu, Y. D.; Zhang, W. J.; Kong, X. Q.; Zhao, X.

2016-03-01

The heat-transfer behavior of the interface of Flyer plate (or Base Plate) has great influence on the microcosmic structures, stress distributions, and interface distortion of the welded interface of composite plates by explosive welding. In this paper, the temperature distributions in the combing zone are studied for the case of Cu/Fe composite plate jointed by explosive welding near the lower limit of explosive welding. The results show that Flyer plate (Cu plate) and Base Plate (Fe plate) firstly almost have the same melting rate in the explosive welding process. Then, the melting rate of Cu plate becomes higher than that of Fe plate. Finally, the melt thicknesses of Cu plate and Fe plate trend to be different constants, respectively. Meanwhile, the melting layer of Cu plate is thicker than that of Fe plate. The research could supply some theoretical foundations for calculating the temperature distribution and optimizing the explosive welding parameters of Cu/Fe composite plate to some extent.

Petrologic Modeling of Magmatic Evolution in The Elysium Volcanic Province

NASA Astrophysics Data System (ADS)

Susko, D.; Karunatillake, S.; Hood, D.

2017-12-01

The Elysium Volcanic Province (EVP) on Mars is a massive expanse of land made up of many hundreds of lava flows of various ages1. The variable surface ages within this volcanic province have distinct elemental compositions based on the derived values from the Gamma Ray Spectrometer (GRS) suite2. Without seismic data or ophiolite sequences on Mars, the compositions of lavas on the surface provide some of the only information to study the properties of the interior of the planet. The Amazonian surface age and isolated nature of the EVP in the northern lowlands of Mars make it ideal for analyzing the mantle beneath Elysium during the most recent geologic era on Mars. The MELTS algorithm is one of the most commonly used programs for simulating compositions and mineral phases of basaltic melt crystallization3. It has been used extensively for both terrestrial applications4 and for other planetary bodies3,5. The pMELTS calibration of the algorithm allows for higher pressure (10-30 kbars) regimes, and is more appropriate for modeling melt compositions and equilibrium conditions for a source within the martian mantle. We use the pMELTS program to model how partial melting of the martian mantle could evolve magmas into the surface compositions derived from the GRS instrument, and how the mantle beneath Elysium has changed over time. We attribute changes to lithospheric loading by long term, episodic volcanism within the EVP throughout its history. 1. Vaucher, J. et al. The volcanic history of central Elysium Planitia: Implications for martian magmatism. Icarus 204, 418-442 (2009). 2. Susko, D. et al. A record of igneous evolution in Elysium, a major martian volcanic province. Scientific Reports 7, 43177 (2017). 3. El Maarry, M. R. et al. Gamma-ray constraints on the chemical composition of the martian surface in the Tharsis region: A signature of partial melting of the mantle? Journal of Volcanology and Geothermal Research 185, 116-122 (2009). 4. Ding, S. & Dasgupta, R. The fate of sulfide during decompression melting of peridotite - implications for sulfur inventory of the MORB-source depleted upper mantle. Earth and Planetary Science Letters 459, 183-195 (2017). 5. Sakaia, R., Nagaharaa, H., Ozawaa, K. & Tachibanab, S. Composition of the lunar magma ocean constrained by the conditions for the crust formation. Icarus 229, 45-56 (2014).

The Divnoe meteorite: Petrology, chemistry, oxygen isotopes and origin

NASA Technical Reports Server (NTRS)

Petaev, M. I.; Barsukova, L. D.; Lipschultz, M. E.; Wang, M.-S.; Ariskin, A. A.; Clayton, R. N.; Mayeda, T. K.

1994-01-01

The Divnoe meteorite is an olivine-rich primitive achondrite with subchondritic chemistry and mineralogy. It has a granoblastic, coarse-grained, olivine groundmass (CGL: coarse-grained lithology) with relatively large pyroxene-plagioclase poiklitic patches (PP) and small fine-grained domains of an opaque-rich lithology (ORL). Both PP and ORL are inhomogeneously distributed and display reaction boundaries with the groundmass. Major silicates, olivine Fa(20-28) and orthopyroxyene Fs(20-28 Wo(0.5-2.5), display systematic differences in composition between CGL and ORL as well as a complicated pattern of variations within CGL. Accessory plagioclase has low K content and displays regular igneous zoning with core compositions An(40-45) and rims An(32-37). The bulk chemical composition of Divnoe is similar to that of olivine-rich primitive achondrites, except for a depletion of incompatible elements and minor enrichment of refractory siderophiles. Oxygen isotope compositions for whole-rock and separated minerals from Divnoe fall in a narrow range, with mean delta O-18 = +4.91, delta O-17 = +2.24, and Delta O-17 = -0.26 +/- 0.11. The isotopic composition is not within the range of any previously recognized group but is very close to that of the brachinites. To understand the origin of Divnoe lithologies, partial melting and crystallization were modelled using starting compositions equal to that of Divnoe and some chondritic meteorites. It was found that the Divnoe composition could be derived from a chondritic source region by approximately 20 wt% partial melting at Ta approximately 1300 C and log(fO2) = IW-1.8, followed by approximtely 60 wt% crystallization of the partial melt formed, and removal of the still-liquid portion of the partial melt. Removal of the last partial melt resulted in depletion of the Divnoe plagioclase in Na and K. In this scenario, CGL represents the residue of partial melting, and PP is a portion of the partial melt that crystallized in situ. The ORL was formed during the final stages of partial melting by reaction between gaseous sulfur and residual olivine in the source region. A prominent feature of Divnoe is fine micron-scale chemical variations within olivine grains, related to lamellar structures the olivines display. The origin of these structures is not known.

Experimental constraints on the origin of high-Mg andesites: the effect of H2O and silica activity on mantle melt compositions

NASA Astrophysics Data System (ADS)

Moore, G. M.; Roggensack, K.

2009-12-01

Understanding the role volatiles (H2O, CO2) play in the origin of mantle-related melts is an important part of arc magma petrogenesis, and has implications for our understanding of many aspects of subduction zone volcanism including mass fluxes, volcanic degassing, and eruptive style. Both the occurrence of high-Mg andesites (HMA) in particular tectonic settings and their association with high H2O contents make HMA a unique window into hydrous subduction-related mantle melting processes. A significant amount of experimental work at mantle conditions has shown that increasing H2O content in the melt will not only stabilize olivine with respect to orthopyroxene, but will also increase the SiO2 content of the melt to andesitic amounts (e.g. Gaetani and Grove, 1998; Tatsumi, 1981; Tatsumi, 2006), suggesting that HMA could be a primary mantle melt if enough H2O is present. This hypothesis is supported by the rare occurrence of mantle xenoliths in Mg-rich andesites (Blatter and Carmichael, 1998; Tanaka and Aoki, 1981) that often contain hydrous mineral phases. Reliable thermodynamic modelling of such hydrous silicate melts in equilibrium with the mantle has proven difficult because of the relatively small set of experiments that allow this type of analysis. There are also experimental and analytical difficulties in dealing with hydrous high P-T samples (e.g. quench to a glass, rapid melt-solid reaction on quench, electron beam sensitivity of resulting glass, volatile content determination, etc), and statistical difficulties in determining robust model parameters because of the large degree of co-variance in the data set (e.g. T and H2O melt content). With the goal of addressing these problems, we conducted a series of “sandwich” type experiments at 1.0 GPa and 1200 deg C that saturated various hydrous melt compositions with olivine and opx. Our previous results have shown that the silica activity coefficient correlates negatively with H2O content (Moore and Roggensack, 2007), consistent with the earlier experimental phase equilibria results and the modeling of Carmichael (2002). New results using a broader range of starting melt compositions are presented here, showing that there is a significant effect of initial alkali content on the amount of melting of the mineral assemblage. This has the net result that the experimental melt compositions converge to a narrow range at high H2O contents that do not reproduce the observed HMA compositions, implying that the experimental P-T conditions used are not correct for generating HMA magmas. Use of this new data to thermodynamically model the influence of P, T, and melt composition (including H2O content) is underway, and will constrain whether hydrous arc lavas, including HMA, can be attributed to a primitive mantle origin, or whether other magmatic processes are necessary to generate their observed bulk compositions. It will also quantify the amount of H2O necessary to generate such magmas, giving insight into the potential H2O content present in the sub-arc mantle source regions, and allowing a more precise estimate of volatile fluxes in volcanic arc settings.

Cannibalism of olivine-rich cumulate xenoliths during the 1998 eruption of Piton de la Fournaise (La Réunion hotspot): Implications for the generation of magma diversity

NASA Astrophysics Data System (ADS)

Salaün, A.; Villemant, B.; Semet, M. P.; Staudacher, T.

2010-12-01

Contrasting with its unusual isotopic homogeneity compared to other hotspot volcanoes, Piton de la Fournaise has produced a large diversity of basaltic magmas over its 0.5 Ma history: picrites and two types of transitional basalts with distinct petrological and chemical compositions. A minor group of evolved basalts (anomalous group of basalts or AGB) is enriched in both compatible (Mg, Fe, Ti, Cr, and Ni) and incompatible (K, Th, and La) elements and depleted in Ca and Si relative to the dominant group of evolved basalts. The 1998 eruption simultaneously produced the two basaltic types at two distinct vents (Hudson vent: AGB, Kapor vent: common basalt) but from the same feeding conduit. Glasses of both magmas are close in composition and belong to the single differentiation trend defined by all 1998-2007 glass compositions. Thermodynamic model (MELTS code) shows that AGB-type magmas cannot be produced by high pressure (> 1 GPa) clinopyroxene fractionation as previously proposed and that all melts of the 1998-2007 activity period are produced by low pressure (< 800 MPa) crystal fractionation from the most primitive basalt (MgO ~ 9%). Modal composition of 1998 lavas (mass balance calculation and SEM image analysis) and olivine crystal composition show that Hudson lavas have assimilated significant fractions of olivine xenocrysts contrary to Kapor lavas. In addition, the higher incompatible element contents of Hudson lavas suggest contamination by a differentiated (trachytic) melt. All AGB share the following characteristics: (i) evolved glass compositions, (ii) 5-10% olivine xenocrysts, and (iii) vents located in a narrow region at the summit of the edifice. They are interpreted as the result of the assimilation of olivine-rich xenoliths either by evolved melts or by basaltic melts contaminated by low fractions of differentiated melts produced from interstitial glass frequently coating cumulates minerals or resulting from partial melting of cumulates bearing pyroxene or plagioclase (wehrlitic to gabbroic cumulates). The scarcity of AGB magmas is attributed to their shallow transfer path in rarely intruded lateral zones of Piton de la Fournaise volcano: wehrlitic to gabbroic cumulates bodies are either heterogeneously distributed within the edifice or have been depleted in low melting point components in the 'Rift Zone' where most of the recent eruptive events are emplaced. These results emphasize the exceptional chemical homogeneity of the primary basaltic melt involved in volcanic activity of Piton de la Fournaise hotspot for 0.5 Ma and the increasingly recognized role of magma-wall rock interactions in erupted magma compositions.

Study of the production of unique new glasses

NASA Technical Reports Server (NTRS)

Happe, R. A.

1972-01-01

A number of high new oxide glasses have been prepared by a laser-spin melting technique where droplets are ejected from a molten mass. Techniques have been developed for measuring the optical properties of most of the new glasses so produced. A preliminary study of processing equipment for producing new glasses in a zero gravity environment onboard manned space laboratory is reported. Induction and laser melting emerge as preferred techniques for melting spheroids of new glass compositions in space. Sample calculations for power required to induction melt new glass compositions are presented. Cooling rate calculations show that radiation cooling of the high melting materials results in very short cooling times for 1/2 inch diameters to temperatures where the spheroids can be handled.

Asthenospheric kimberlites: Volatile contents and bulk compositions at 7 GPa

NASA Astrophysics Data System (ADS)

Stamm, Natalia; Schmidt, Max W.

2017-09-01

During ascent, kimberlites react with the lithospheric mantle, entrain and assimilate xenolithic material, loose volatiles and suffer from syn- and post-magmatic alteration. Consequently, kimberlite rocks deviate heavily from their primary melt. Experiments at 7 GPa, 1300-1480 °C, 10-30 wt% CO2 and 0.46 wt% H2O on a proposed primitive composition from the Jericho kimberlite show that saturation with a lherzolitic mineral assemblage occurs only at 1300-1350 °C for a carbonatitic melt with <8 wt% SiO2 and >35 wt% CO2. At asthenospheric temperatures of >1400 °C, where the Jericho melt stays kimberlitic, this composition saturates only in low-Ca pyroxene, garnet and partly olivine. We hence forced the primitive Jericho kimberlite into multiple saturation with a lherzolitic assemblage by adding a compound peridotite. Saturation in olivine, low- and high-Ca pyroxene and garnet was obtained at 1400-1650 °C (7 GPa), melts are kimberlitic with 18-29 wt% SiO2 + Al2O3, 22.1-24.6 wt% MgO, 15-27 wt% CO2 and 0.4-7.1 wt% H2O; with a trade-off of H2O vs. CO2 and temperature. Melts in equilibrium with high-Ca pyroxene with typical mantle compositions have ≥2.5 wt% Na2O, much higher than the commonly proposed 0.1-0.2 wt%. The experiments allow for a model of kimberlite origin in the convective upper mantle, which only requires mantle upwelling that causes melting at the depth where elemental carbon (in metal, diamond or carbide) converts to CO2 (at ∼250 km). If primary melts leading to kimberlites contain a few wt% H2O, then adiabatic temperatures of 1400-1500 °C would yield asthenospheric mantle melts that are kimberlitic (>18 wt% SiO2 + Al2O3) but not carbonatitic (<10 wt% SiO2 + Al2O3) in composition, carbonatites only forming 100-200 °C below the adiabat. These kimberlites represent small melt fractions concentrating CO2 and H2O and then acquire part of their chemical signature by assimilation/fractionation during ascent in the subcratonic lithosphere.

Method for preparing homogeneous single crystal ternary III-V alloys

DOEpatents

Ciszek, Theodore F.

1991-01-01

A method for producing homogeneous, single-crystal III-V ternary alloys of high crystal perfection using a floating crucible system in which the outer crucible holds a ternary alloy of the composition desired to be produced in the crystal and an inner floating crucible having a narrow, melt-passing channel in its bottom wall holds a small quantity of melt of a pseudo-binary liquidus composition that would freeze into the desired crystal composition. The alloy of the floating crucilbe is maintained at a predetermined lower temperature than the alloy of the outer crucible, and a single crystal of the desired homogeneous alloy is pulled out of the floating crucible melt, as melt from the outer crucible flows into a bottom channel of the floating crucible at a rate that corresponds to the rate of growth of the crystal.

Method for producing melt-infiltrated ceramic composites using formed supports

DOEpatents

Corman, Gregory Scot; Brun, Milivoj Konstantin; McGuigan, Henry Charles

2003-01-01

A method for producing shaped articles of ceramic composites provides a high degree of dimensional tolerance to these articles. A fiber preform is disposed on a surface of a stable formed support, a surface of which is formed with a plurality of indentations, such as grooves, slots, or channels. Precursors of ceramic matrix materials are provided to the fiber preform to infiltrate from both sides of the fiber preform. The infiltration is conducted under vacuum at a temperature not much greater than a melting point of the precursors. The melt-infiltrated composite article substantially retains its dimension and shape throughout the fabrication process.

Oxygen and iron production by electrolytic smelting of lunar soil

NASA Technical Reports Server (NTRS)

Colson, R. O.; Haskin, L. A.

1991-01-01

Oxygen, present in abundance in nearly all lunar materials, can theoretically be extracted by molten silicate electrolysis from any known lunar rock. Derivation of oxygen by this method has been amply demonstrated experimentally in silicate melts of a variety of compositions. This work can be divided into three categories: (1) measurement of solubilities of metals (atomic) in silicate melts; (2) electrolysis experiments under various conditions of temperature, container material, electrode configuration, current density, melt composition, and sample mass (100 to 2000 mg) measuring energy required and character of resulting products; and (3) theoretical assessment of compositional requirements for steady state operations of an electrolysis cell.

Description of the containerless melting of glass in low gravity

NASA Technical Reports Server (NTRS)

Ray, C. S.; Day, D. E.

1983-01-01

A brief description is given of a single-axis, acoustic levitator/furnace apparatus used to position, heat, melt, and quench multicomponent oxide, glass-forming compositions in low gravity. This apparatus is capable of processing eight approximately spherical samples (about 6 mm diameter) at temperatures up to 1550 C in a dry air atmosphere. Results are also presented for a containerless melting experiment conducted on SPAR VI where a ternary CaO-Ga2O3-SiO2 composition was levitated and quenched to a glass. Selected properties of the glass prepared on SPAR VI are compared with the properties of glass samples of identical composition prepared on earth.

Assimilation by lunar mare basalts: Melting of crustal material and dissolution of anorthite

NASA Astrophysics Data System (ADS)

Finnila, A. B.; Hess, P. C.; Rutherford, M. J.

1994-07-01

We discuss techniques for calculating the amount of crustal assimilation possible in lunar magma chambers and dikes based on thermal energy balances, kinetic rates, and simple fluid mechanical constraints. Assuming parent magmas of picritic compositions, we demonstrate the limits on the capacity of such magmas to melt and dissolve wall rock of anorthitic, troctolitic, noritic, and KREEP (quartz monzodiorite) compositions. Significant melting of the plagioclase-rich crustal lithologies requires turbulent convection in the assimilating magma and an efficient method of mixing in the relatively buoyant and viscous new melt. Even when this occurs, the major element chemistry of the picritic magmas will change by less than 1-2 wt %. Diffusion coefficients measured for Al2O3 from an iron-free basalt and an orange glass composition are 10-12 sq m/s at 1340 C and 10-11 sq m/s at 1390 C. These rates are too slow to allow dissolution of plagioclase to significantly affect magma compositions. Picritic magmas can melt significant quantities of KREEP, which suggests that their trace element chemistry may still be affected by assimilation processes; however, mixing viscous melts of KREEP composition with the fluid picritic magmas could be prohibitively difficult. We conclude that only a small part of the total major element chemical variation in the mare basalt and volcanic glass collection is due to assimilation/fractional crystallization processes near the lunar surface. Instead, most of the chemical variation in the lunar basalts and volcanic glasses must result from assimilation at deeper levels or from having distinct source regions in a heterogeneous lunar mantle.

Assimilation by lunar mare basalts: Melting of crustal material and dissolution of anorthite

NASA Technical Reports Server (NTRS)

Finnila, A. B.; Hess, P. C.; Rutherford, M. J.

1994-01-01

We discuss techniques for calculating the amount of crustal assimilation possible in lunar magma chambers and dikes based on thermal energy balances, kinetic rates, and simple fluid mechanical constraints. Assuming parent magmas of picritic compositions, we demonstrate the limits on the capacity of such magmas to melt and dissolve wall rock of anorthitic, troctolitic, noritic, and KREEP (quartz monzodiorite) compositions. Significant melting of the plagioclase-rich crustal lithologies requires turbulent convection in the assimilating magma and an efficient method of mixing in the relatively buoyant and viscous new melt. Even when this occurs, the major element chemistry of the picritic magmas will change by less than 1-2 wt %. Diffusion coefficients measured for Al2O3 from an iron-free basalt and an orange glass composition are 10(exp -12) sq m/s at 1340 C and 10(exp -11) sq m/s at 1390 C. These rates are too slow to allow dissolution of plagioclase to significantly affect magma compositions. Picritic magmas can melt significant quantities of KREEP, which suggests that their trace element chemistry may still be affected by assimilation processes; however, mixing viscous melts of KREEP composition with the fluid picritic magmas could be prohibitively difficult. We conclude that only a small part of the total major element chemical variation in the mare basalt and volcanic glass collection is due to assimilation/fractional crystallization processes near the lunar surface. Instead, most of the chemical variation in the lunar basalts and volcanic glasses must result from assimilation at deeper levels or from having distinct source regions in a heterogeneous lunar mantle.

A Study on New Composite Thermoplastic Propellant

NASA Astrophysics Data System (ADS)

Kahara, Takehiro; Nakayama, Masanobu; Hasegawa, Hiroshi; Katoh, Kazushige; Miyazaki, Shigehumi; Maruizumi, Haruki; Hori, Keiichi; Morita, Yasuhiro; Akiba, Ryojiro

Efforts have been paid to realize a new composite propellant using thermoplastics as a fuel binder and lithium as a metallic fuel. Thermoplastics binder makes it possible the storage of solid propellant in small blocks and to provide propellants blocks into rocket motor case at a quantity needed just before use, which enables the production facility of solid propellant at a minimum level, thus, production cost significantly lower. Lithium has been a candidate for a metallic fuel for the ammonium perchlorate based composite propellants owing to its capability to reduce the hydrogen chloride in the exhaust gas, however, never been used because lithium is not stable at room conditions and complex reaction products between oxygen, nitrogen, and water are formed at the surface of particles and even in the core. However, lithium particles whose surface shell structure is well controlled are rather stable and can be stored in thermoplastics for a long period. Evaluation of several organic thermoplastics whose melting temperatures are easily tractable was made from the standpoint of combustion characteristics, and it is shown that thermoplastics propellants can cover wide range of burning rate spectrum. Formation of well-defined surface shell of lithium particles and its kinetics are also discussed.

Impact melts in the MAC88105 lunar meteorite - Inferences for the lunar magma ocean hypothesis and the diversity of basaltic impact melts

NASA Technical Reports Server (NTRS)

Taylor, G. J.

1991-01-01

The MAC88105 lunar meteorite, as represented by thin section 78, contains three major types of impact melt breccias. The most abundant type is clast-laden, fine-grained, and rich in Al2O3 (28 wt pct); these clasts constitute most of the meteorite. Their abundance and aluminous nature indicate that the MAC88105 source area was very aluminous. This is consistent with formation of the primordial lunar crust from a global magma ocean. The second type of impact melt is represented by only one clast in 78. It has a basaltic bulk composition similar to many other lunar impact melts, but is significantly richer in P2O5 than most and has a much lower MgO/(MgO + FeO). The third impact-melt type resembles a prominent melt group at Apollo 16, but has lower MgO/(MgO + FeO). These data show that basaltic impact melts are compositionally diverse. Dating samples of the Al-rich impact melts and the new types of basaltic impact melts from this meteorite can test the idea that the Moon suffered a terminal cataclysm 3.9 Ga ago.

Melt Transport and Mantle Assimilation at Atlantis Massif (IODP Site U1309): Evidence from Chemical Profiles along Olivine Crystallographic Axes

NASA Astrophysics Data System (ADS)

Ferrando, C.; Godard, M.; Ildefonse, B.; Rampone, E.

2017-12-01

Olivine-rich troctolites (Ol > 70%, Ol T) indicate that extensive melt impregnation of preexisting Ol rich lithologies participate to the building of slow spread crust. To constrain their origin and their impact on the structure and geochemistry of oceanic crust, we realized a multi-scale petro-structural, geochemical, and numerical modelling study of Ol T drilled at IODP Hole U1309D (Atlantis Massif, Exp. 304/305). Ol T display deformed (high temperature imprint) corroded coarse grained to undeformed fine grained Ol embayed in poikilitic Cpx and Plg. Ol crystallographic preferred orientations show [001] cluster suggesting formation after impregnation and assimilation of a deformed Ol rich matrix at high melt/rock ratios. Ol have variable major and minor element compositions, but similar fractionated REE (DyN/YbN = 0.04 - 0.11). Chemical traverses along principal crystallographic axes of Ol are flat suggesting local equilibrium between Ol and neighboring phases. 3 types of Ol T were distinguished. Ol T 1 - 2 display sharp contacts. Ol T 1 has Ol <75% (single grains) and primitive compositions (Mg# = 85-86; Ni = 1870-2840 ppm, Mn = 1570-1950 ppm; Li = 1.2 - 2.7 ppm). Ol T 2 have high Ol ( > 75%, dominantly aggregates) yet more evolved composition (Mg# = 83-84, Ni = 1790 - 2510 ppm, Mn = 1760 - 1990 ppm, Li = 1.5 - 3.9 ppm) in contrast to modal and composition trends predicted by MORB crystallization. Ol T 3 has diffusive contacts with gabbroic veins, variable modal Ol with the most evolved compositions and record late stages of Ol-T formation. Ol T compositions are best modelled assuming percolation of primitive MORB melts into Hole U1309B harzburgite, triggering Opx dissolution, followed by Ol assimilation and Plg + Cpx crystallization. Modelling shows that Ol Ni variations at constant Mg# in Ol T are mantle inherited. Ol T 1 compositions were fitted assuming higher Ol assimilation (Ma = 0.06 - 0.13) in contrast to Ol T 2 -3 (Ma = 0.01 - 0.02). Ol T 3 was `buffered' by more evolved melts and shows cooling of reacted melts. We interpret the 3 Ol T types as resulting from initial local spatial variations in mantle permeability (pyroxene distribution?) which in turn controlled melt transport and mantle-melt interactions. We expect that such reactive percolation processes will shift MORB compositions to apparent high pressure fractionation.

CaCu3Ti4O12-PVDF polymeric composites with enhanced capacitive energy density

NASA Astrophysics Data System (ADS)

Ouyang, Xin; Cao, Peng; Zhang, Weijun; Liu, Zhuofeng; Huang, Zhaohui; Gao, Wei

2015-03-01

CaCu3Ti4O12 (CCTO)-poly(vinylidene fluoride (PVDF)) composites were prepared by melt blending and hot molding techniques. The addition of CCTO remarkably enhanced the dielectric properties and the thermal conductivity of PVDF composites, while the melting point of the PVDF composites ( 170°C) was almost independent of the CCTO concentration. Based on the results of dielectric constant and dielectric breakdown voltage, the PVDF composite containing 40 vol.% CCTO fillers shows the optimized capacitive energy storage potential (7.81 J/cm3).

Origin of the Powai ankaramite, and the composition, P-T conditions of equilibration and evolution of the primary magmas of the Deccan tholeiites

NASA Astrophysics Data System (ADS)

Chatterjee, Nilanjan; Sheth, Hetu

2015-03-01

The Powai ankaramite flow from Mumbai, western Deccan Traps, contains abundant crystals of augite (En59-47Fs10-14Wo27-42, 22-40 modal %, 3-5 mm) and olivine (Fo84-74, 11-16 modal %, 1-2 mm), and minor plagioclase (An71, ~0.5 mm) embedded in a fine-grained matrix. Minor orthopyroxene (En79-77Fs16-19Wo5-4) with irregular and embayed margins is mantled by thick augite overgrowth rims. The Fe-Mg distribution between the large crystals and bulk rock shows disequilibrium, indicating that the ankaramite is a cumulate rock. The ankaramite probably formed by the intrusion of tholeiitic melt into a cumulate pile with olivine, augite, and orthopyroxene left by the crystallization of earlier magmas, resulting in orthopyroxene dissolution and subsequent precipitation of augite. Olivine-hosted melt inclusions and melts represented by the ankaramite groundmass and some associated tholeiitic dikes are multiply saturated with olivine + plagioclase + clinopyroxene at ≤6 kb according to phase equilibrium constraints. Calculations involving incremental addition of equilibrium phases to these melts and to the common aphyric tholeiites of the voluminous Ambenali and Mahabaleshwar Formations show that their primary magmas (wt% SiO2: 48-50, MgO: 9.8-11.8, and FeO: 7.2-7.9, and Mg# 70-74) last equilibrated with spinel lherzolite at ~8-13 kb (~30-49 km depths) and ~1268-1332 °C, and trace element considerations indicate ≤15 % batch melting of mantle. These tholeiitic primary magmas then underwent olivine gabbro fractionation in upper crustal magma chambers at depths ≤23 km. The minimum depth of equilibration of the primary magmas is shallower than the present-day Moho in the Mumbai area based on seismological data, indicating localized mantle upwelling and lower crustal interactions previously inferred from the Nd-Sr isotopic ratios and other geochemical characteristics of the ankaramite and associated tholeiites.

Solvent Free Low-Melt Viscosity Imide Oligomers And Thermosetting Polyimide Composites

NASA Technical Reports Server (NTRS)

Chuang, CHun-Hua (Inventor)

2006-01-01

This invention relates to the composition and a solvent-free process for preparing novel imide oligomers and polymers specifically formulated with effective amounts of a dianhydride such as 2,3,3',4-biphenyltetra carboxylic dianydride (a-BPDA), at least one aromatic diamine' and an endcapped of 4-phenylethynylphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260-280" C. When the imide oligomer melt is cured at about 371 C. in a press or autoclave under 100-500 psi, the melt resulted in a thermoset polyimide having a glass transition temperature (T(sub g)) equal to and above 310 C. A novel feature of this process is that the monomers; namely the dianhydrides, diamines and the endcaps, are melt processable to form imide oligomers at temperatures ranging between 232-280 C. (450-535 F) without any solvent. These low-melt imide oligomers can be easily processed by resin transfer molding (RTM), vacuum-assisted resin transfer molding (VARTM) or the resin infusion process with fiber preforms e.g. carbon, glass or quartz preforms to produce polyimide matrix composites with 288-343C (550-650 F) high temperature performance capability.

Lithologies contributing to the clast population in Apollo 17 LKFM basaltic impact melts

NASA Technical Reports Server (NTRS)

Norman, Marc D.; Taylor, G. Jeffrey; Spudis, Paul; Ryder, Graham

1992-01-01

LKFM basaltic impact melts are abundant among Apollo lunar samples, especially those from Apollo 15, 16, and 17. They are generally basaltic in composition, but are found exclusively as impact melts. They seem to be related to basins and so could represent the composition of the lower lunar crust. They contain lithic clasts that cannot be mixed in any proportion to produce the composition of the melt matrix; components rich in transition elements (Ti, Cr, Sc) and REE are not considered. To search for the mysterious cryptic component, we previously investigated the mineral clast population in two Apollo 14 LKFM basaltic impact melts, 15445 and 15455. The cryptic component was not present in the mineral clast assemblage of these breccias either, but some olivine and pyroxene grains appeared to be from lithologies not represented among identified igneous rocks from the lunar highlands. In addition, none of the mineral clasts could be unambiguously assigned to a ferroan anorthosite source. We have now extended this study to Apollo 17, starting with two LKFM impact melt breccias (76295 and 76315) from the Apollo 17 station 6 boulder. The results from the study are presented.

Experimental Constraints on the Partitioning Behavior of F, Cl, and OH Between Apatite and Basaltic Melt

NASA Technical Reports Server (NTRS)

McCubbin, Francis M.; Barnes, Jessica J.; Vander Kaaden, Kathleen E.; Boyce, Jeremy W.; Ustunisik, Gokce; Whitson, Eric S.

2017-01-01

The mineral apatite is present in a wide range of planetary materials. The presence of volatiles (F, Cl, and OH) within its crystal structure (X-site) have motivated numerous studies to investigate the partitioning behavior of F, Cl, and OH between apatite and silicate melt with the end goal of using apatite to constrain the volatile contents of planetary magmas and mantle sources. A number of recent experimental studies have investigated the apatite-melt partitioning behavior of F, Cl, and OH in magmatic systems. Apatite-melt partitioning of volatiles are best described as exchange equilibria similar to Fe-Mg partitioning between olivine and silicate melt. However, the partitioning behavior is likely to change as a function of temperature, pressure, oxygen fugacity, apatite composition, and melt composition. In the present study, we have conducted experiments to assess the partitioning behavior of F, Cl, and OH between apatite and silicate melt over a pressure range of 0-6 gigapascals, a temperature range of 950-1500 degrees Centigrade, and a wide range of apatite ternary compositions. All of the experiments were conducted between iron-wustite oxidation potentials IW minus 1 and IW plus 2 in a basaltic melt composition. The experimental run products were analyzed by a combination of electron probe microanalysis and secondary ion mass spectrometry (NanoSIMS). Temperature, apatite crystal chemistry, and pressure all play important roles in the partitioning behavior of F, Cl, and OH between apatite and silicate melt. In portions of apatite ternary space that undergo ideal mixing of F, Cl, and OH, exchange coefficients remain constant at constant temperature and pressure. However, exchange coefficients vary at constant temperature (T) and pressure (P) in portions of apatite compositional space where F, Cl, and OH do not mix ideally in apatite. The variation in exchange coefficients exhibited by apatite that does not undergo ideal mixing far exceeds the variations induced by changes in temperature (T) or pressure (P) . In regions where apatite undergoes ideal mixing of F, Cl, and OH, temperature has a stronger effect than pressure on the partitioning behavior, but both are important. Furthermore, fluorine becomes less compatible in apatite with increasing pressure and temperature. We are still in the process of analyzing our experimental run products, but we plan to quantify the effects of P and T on apatite-melt partitioning of F, Cl, and OH.

The effects of small amounts of H2O on partial melting of model spinel lherzolite in the system CMAS

NASA Astrophysics Data System (ADS)

Liu, X.; St. C. Oneill, H.

2003-04-01

Water (H_2O) is so effective at lowering the solidus temperatures of silicate systems that even small amounts of H_2O are suspected to be important in the genesis of basaltic magmas. The realization that petrologically significant amounts of H_2O can be stored in nominally anhydrous mantle minerals (olivine and pyroxenes) has fundamental implications for the understanding of partial melting in the mantle, for it implies that the role that H_2O plays in mantle melting may not be appropriately described by models in which the melting is controlled by hydrous phases such as amphibole. Although the effect of water in suppressing the liquidus during crystallization is quite well understood, such observations do not provide direct quantitative information on the solidus. This is because liquidus crystallization occurs at constant major-element composition of the system, but at unbuffered component activities (high thermodynamic variance). By contrast, for partial melting at the solidus the major-element component activities are buffered by the coexisting crystalline phases (low variance), but the major-element composition of the melt can change as a function of added H_2O. Accordingly we have determined both the solidus temperature and the melt composition in the system CMAS with small additions of H_2O, to 4 wt%, in equilibrium with the four-phase lherzolite assemblage of fo+opx+cpx+sp. Experiments were conducted at 1.1 GPa and temperatures from 1473 K to the dry solidus at 1593 K in a piston-cylinder apparatus. Starting materials were pre-synthesised assemblage of fo+opx+cpx+sp, plus an oxide/hydroxide mix of approximately the anticipated melt composition. H_2O was added as either Mg(OH)_2 or Al(OH)_3. The crystalline assemblage and melt starting mix were added as separate layers inside sealed Pt capsules, to ensure large volumes of crystal-free melt. After the run doubly polished sections were prepared in order to analyse the quenched melt by FTIR spectroscopy, to quantify the amounts of H_2O. This is necessary, as Pt capsules are to some extent open to H_2 diffusion. All melts were found to contain CO_2 (<0.7 wt%), which appears to come mainly from the hydroxide starting materials but also by C diffusion through the Pt capsule. Since CO_2 is experimentally correlated with H_2O, its presence significantly effects the interpretation of the results. Ignoring this complication, we find that 1 wt% H_2O decreases the solidus by ˜40 K; melt compositions do not change greatly, the main effect being a small decrease in MgO.

A multi-component evaporation model for beam melting processes

NASA Astrophysics Data System (ADS)

Klassen, Alexander; Forster, Vera E.; Körner, Carolin

2017-02-01

In additive manufacturing using laser or electron beam melting technologies, evaporation losses and changes in chemical composition are known issues when processing alloys with volatile elements. In this paper, a recently described numerical model based on a two-dimensional free surface lattice Boltzmann method is further developed to incorporate the effects of multi-component evaporation. The model takes into account the local melt pool composition during heating and fusion of metal powder. For validation, the titanium alloy Ti-6Al-4V is melted by selective electron beam melting and analysed using mass loss measurements and high-resolution microprobe imaging. Numerically determined evaporation losses and spatial distributions of aluminium compare well with experimental data. Predictions of the melt pool formation in bulk samples provide insight into the competition between the loss of volatile alloying elements from the irradiated surface and their advective redistribution within the molten region.

Tracing mantle processes with Fe isotopes

NASA Astrophysics Data System (ADS)

Weyer, S.; Ionov, D.

2006-12-01

High precision Fe isotope measurements have been performed on various mantle peridotites (fertile lherzolites, harzburgites, metasomatised Fe-enriched rocks) and volcanic rocks (mainly oceanic basalts) from different localities and tectonic settings. Pimitive peridotites (Mg# = 0.894) yield delta56Fe = 0.02 and are significantly lighter than the basalts (average delta56Fe = 0.11). Furthermore, the peridotites display a negative correlation of iron isotopes with Mg#. Taken together, these findings imply that Fe isotopes fractionate during partial melting, with heavy isotopes preferentially entering the melt [1, 2]. A particularly good correlation of the Fe isotope composition and Mg# shown by poorly metasomatised spinel lherzolites of three localities (Horoman, Kamchatka and Lherz) was used to model Fe isotope fractionation during partial melting, resulting in alphamantle-melt = 1.0003. This value implies higher Fe isotope fractionation between residual mantle and mantle-derived melts (i.e. Delta56Femantle-melt = 0.2-0.3) than the observed difference between the peridotites and the basalts in this study. Our data on plagioclase lherzolites from Horoman and spinel lherzolites from other localities indicate that the difference in Fe isotope composition between mantle and basalts may be reduced by partial re-equilibration between the isotopically heavy basalts and the isotopically light depleted lithospheric mantle during melt ascent. Besides partial melting, the Fe isotope composition of mantle peridotites can also be significantly modified by metasomatic events. At two localities (Tok, Siberia and Tariat, Mongolia) Fe isotopes correlates with the Fe concentration of the peridotites, which was increased up to 14.5% FeO by melt percolation. Such processes can be accompanied by chromatographic effects and produce a range of Fe isotope compositions in the percolation columns, from extremely light to heavy (delta56Fe = -0.42 to +0.17). We propose that Fe isotopes can be used as a sensitive tracer to identify such metasomatic processes in the mantle. [1] Weyer et al. (2005) EPSL 240: 251-264 [2] Williams et al. (2005) EPSL 235 : 435-452

The Formation of Novel Thermoplastic Composites from Liquid Crystalline Polymers and Their Blends

DTIC Science & Technology

1991-07-01

melting point of the Vectra. This is due to the long relaxation time of the LCPs ccjzIed with the much higher viscosity of the matrix polymer. Ultem...the LCP reinforcing characteristics i.e. orientation and morphology can be retained upon post-processing provided that the melting point of the LCP is...isothermal compression molding and involves deforming the composites in a cold press after heating the blends at temperatures below the melting point of

The Influence of Technological Regimes of Synthesizing a Solar Furnace on the Phase Composition of TiO2-CuO Cermets and the Optical Properties of Coatings on Their Basis

NASA Astrophysics Data System (ADS)

Suleimanov, S. Kh.; Dyskin, V. G.; Dzhanklich, M. U.; Dudko, O. A.; Kulagina, N. A.

2018-01-01

We present the results of studying the effect of technological synthesis regimes of a solar furnace using the method of a partial metal reduction of one of the oxides on the phase formation of cermet composite materials of the TiO2-CuO system. It has been established that the phase composition of the synthesized cermet composite materials depends on the carbon concentration, melting temperature and cooling rate. The dependence of the spectral-optical properties of selectively absorbing coatings on the production technology and properties of synthesized composite materials has been presented. It has been found that the coatings fabricated by melting in air with overheating at a melt cooling rate of about 105-106°C/s have the highest values of the integral absorption coefficient, α s = 91.0-94.5%.

Processing and Properties of SiC/MoSi2-SiC Composites Fabricated by Melt Infiltration

NASA Technical Reports Server (NTRS)

Bhatt, Ramakrishna T.; Hebsur, Mohan G.

2000-01-01

Hi-Nicalon SiC fiber reinforced MoSi2-SiC matrix composites (SiC/MoSi2-SiC) have been fabricated by the melt infiltration approach. The composite consists of approximately 60 vol%, 2-D woven BN/SiC coated Hi-Nicalon SiC fibers and approximately 40 vol% MoSi2-SiC matrix. The room temperature tensile properties and thermal conductivity of the SiC/MoSi2-SiC composites were measured and compared with those of the melt infiltrated SiC/SiC composites. The influence oi fiber architecture on tensile properties was also evaluated. Results indicate that the primary modulus, stress corresponding to deviation from linearity, and transverse thermal conductivity values for the SiC/MoSi2-SiC composites are significantly lower than those for the SiC/SiC composites. Microcracking of the matrix due to the large difference in thermal expansion between MoSi2 and SiC appears to be the reason for the lower matrix dominated properties of SiC/MoSi2-SiC composites.

Oceanic Volcanism from the Low-Velocity Zone - Without Mantle Plumes (Invited)

NASA Astrophysics Data System (ADS)

Presnall, D. C.; Gudfinnsson, G. H.

2010-12-01

The existence of hot mantle plumes is addressed by using a combination of regional and global shear-wave data, major-element compositions of Hawaiian and MORB glasses (including Iceland), and phase relations for natural lherzolite and the systems CaO-MgO-Al2O3-SiO2-CO2 and CaO-MgO-Al2O3-SiO2-Na2O-FeO. At the East Pacific Rise, the depth of minimum shear wave velocity (Vsv), which we interpret to be the depth of maximum melting, occurs at ~65 km (Webb & Forsyth, 1998, Science, 280, 1229; Conder et al., 2002, JGR, 107, 2344)). This depth increases with lithospheric age and stabilizes at ~150 km (~5 GPa) for ages > ~75 my (Maggi et al., 2006, GJI, 166, 1384). Variations in shear wave anisotropy follow the same pattern (Ekström, 2000, Geophys. Mon. 121, 239) but with a slightly shallower depth of ~130 km for the maximum shear wave anisotropy of the mature Pacific. For a given volcano, the classical Hawaiian sequence of volcanism is early alkalic lavas extracted at ~3 GPa, 1350°C (Sisson et al., 2009, CMP, 158, 803), then voluminous tholeiitic lavas at ~ 4-5 GPa, 1450-1560°C (~150 km), and final alkalic lavas that contain, on Oahu, nanodiamond-bearing xenoliths (Wirth & Rocholl, 2003, EPSL, 211, 357; Frezotti & Peccerillo, 2007, EPSL, 262, 273) and require melt extraction at a pressure slightly > 6 GPa. This progressive increase in P-T conditions of the Hawaiian source matches the equilibrium magma-stratigraphy vs depth indicated by phase relations along a mature-ocean geotherm. This consistency indicates that Hawaiian volcanism occurs by progressively deeper extraction of magmas from a mature LVZ by fracturing of the overlying LID. No decompression melting or enhanced temperature is indicated. At spreading ridges, including Iceland, the absence of glass compositions that define olivine-controlled crystallization trends and the phase equilibrium constraint that all MORBs are extracted at ~1250-1280°C, 1.2-1.5 GPa (Presnall & Gudfinnsson, 2008, JPet., 49, 615) are in excellent agreement with the seismic observation of minimum shear-wave velocity and maximum shear-wave anisotropy (maximum melting) beneath ridges at ~ 65 km. Thus, all MORBs, including those at Iceland, are extracted within the thermal boundary layer along a perturbed geotherm at temperatures cooler than magma-extraction temperatures at Hawaii. This requires a steepened dT/dP slope of the conductive portion of the geotherm at ridges, which is consistent with oceanic heat-flow data vs crustal age. Mantle temperatures for the strongest plume candidate, Hawaii, are consistent with temperatures of oceanic mantle elsewhere of a corresponding age. Temperatures of magma-extraction along all oceanic ridges are far below temperatures consistent with hot mantle plumes.

The Chemical Structure of the Hawaiian Mantle Plume

NASA Astrophysics Data System (ADS)

Ren, Z.; Hirano, N.; Hirata, T.; Takahashi, E.; Ingle, S.

2004-12-01

Numerous geochemical studies of Hawaiian basaltic lavas have shown that the Hawaiian mantle plume is isotopically heterogeneous. However, the distribution and scale of these heterogeneities remain unknown. This is essentially due to the complex interactions created by melting a heterogeneous source, subsequent aggregation of the melts on their way to the surface, and mixing that takes place in shallow magma chambers prior to eruption. In sum, the measured compositions of bulk lavas may represent only _eaverage_f compositions that do not fully reflect the complexity of either the mantle source heterogeneity and/or chemical structure. Melt inclusions, or samples of the local magma frozen in olivine phenocrysts during their formation, are better at recording the complex magmatic history than are the bulk samples. Here, we report major and trace element compositions of olivine-hosted melt inclusions from submarine Haleakala lavas that were collected by 2001-2002 JAMSTEC cruises measured by EPMA and LA-ICP-MS after homogenization at 1250° C, QFM for 20min. Melt inclusions from the submarine Hana Ridge (Haleakala volcano) show large ranges in CaO/Al2O3 (0.92-1.50), TiO2/Na2O (0.79-1.60) and Sr/Nb (14.56-36.60), Zr/Nb (6.48-16.95), ranging from Kilauea-like to Mauna Loa-like compositions within separately-sampled lavas as well as in a single host lava sample. Bulk rocks geochemistry shows that major element composition and trace element ratios such as Zr/Nb, Sr/Nb (Ren et al., 2004a, in press, J. Petrol.) together with Pb, Nd and Sr isotopic ratios (Ren et al., 2004b, submitted to J. Petrol.) of Haleakala shield volcano also display systematic compositional variation changing from a Kilauea-like in the submarine Hana Ridge (main shield stage) to Kilauea-Mauna Loa-like in the subaerial Honomanu stage (late shield stage, data from Chen and Frey, 1991). Some of the compositional variations in melt inclusions in single rocks are wider range than over-all variation observed in bulk rocks. It is important that both Kilauea-like and Mauna Loa-like compositions co-exist in melt inclusions in single submarine Hana Ridge rocks which are identified as Kilauea-like based on bulk geochemistry. These observations are inconsistent with the current interpretation that magma compositions are controlled by concentric zonation of the Hawaiian mantle plume (e.g. Kea component and Loa component), manifested as the Kea trend and the Loa trend volcanoes (e.g. Hauri, 1996; Lassiter et al., 1996). Our new data from olivine-hosted melt inclusions imply that the chemical structure of the Hawaiian mantle plume is significantly more complicated than previously modeled and the length-scale of chemical heterogeneity must be remarkably smaller than estimated based on bulk rock geochemistry.

Defining the chemical role of H2O in mantle melts: Effect of melt composition and H2O content on the activity of SiO2

NASA Astrophysics Data System (ADS)

Moore, G.; Roggensack, K.

2007-12-01

Quantifying the influence of volatiles (H2O, CO2) on the chemistry of mantle melts is a critical aspect of understanding the petrogenesis of arc magmas. A significant amount of experimental work done on the effect of H2O on the solidii of various mantle compositions, as well as on multiple saturation points of various primitive melts, has shown that H2O stabilizes olivine with respect to orthopyroxene. Or, in other words, at constant activity of SiO2, the presence of H2O decreases the activity coefficient of SiO2 in the melt, potentially leading to mantle melts that have suprisingly high SiO2 contents (Carmichael, 2002). Quantification and modelling of this behavior in hydrous silicate melts in equilibrium with the mantle have proven problematic, due mainly to a relatively small set of experiments that allow this type of thermodynamic analysis, and because of the experimental and analytical difficulties of dealing with hydrous high P-T samples (e.g. quench to a glass, rapid melt-solid reaction on quench, electron beam sensitivity of resulting glass, volatile content determination, etc). A further complication in the existing data includes co-variance of important experimental parameters (e.g. T and H2O content), making robust statistical regression analysis difficult and potentially misleading. We present here results of high P-T experiments conducted at a single pressure and temperature (1.0 GPa, 1200 deg C) that have the specific goal of quantifying the effect of H2O, as well as other melt components, on the activity coefficient of SiO2 in mantle melts. Using a "sandwich" type experiment, basaltic melts are saturated with an olivine plus orthopyroxene mineral assemblage with varying H2O and CO2 contents. The resulting samples have their bulk solid phase and glass compositions determined using EPMA, and the volatile content of the glass is determined by FTIR. The activity of SiO2 is then calculated using the olivine and orthopyroxene compositions. This value is then used, along with the mole fraction of SiO2 that is measured in the glass, to calculate an activity coefficient for SiO2 in that particular melt. The results show that for two starting compositions, H2O clearly has a strong negative effect on the activity coefficient of SiO2, consistent with some earlier intepretations. Further work is being conducted on differing starting compositions, as well as increasing the range of volatile contents, in order to better quantify their influence on this important chemical parameter of mantle melts. Ultimately, these experiments will help determine whether hydrous arc lavas, including high-Mg andesites, can be attributed to a primitive mantle origin, or whether other magmatic processes are necessary to generate their observed bulk compositions. It will also quantify the amount of H2O necessary to generate such magmas, giving insight into the potential H2O content present in the sub-arc mantle source regions, and allowing a more precise estimate of volatile fluxes in volcanic arc settings.

Identification of mothball powder composition by float tests and melting point tests.

PubMed

Tang, Ka Yuen

2018-07-01

The aim of the study was to identify the composition, as either camphor, naphthalene, or paradichlorobenzene, of mothballs in the form of powder or tiny fragments by float tests and melting point tests. Naphthalene, paradichlorobenzene and camphor mothballs were blended into powder and tiny fragments (with sizes <1/10 of the size of an intact mothball). In the float tests, the mothball powder and tiny fragments were placed in water, saturated salt solution and 50% dextrose solution (D50), and the extent to which they floated or sank in the liquids was observed. In the melting point tests, the mothball powder and tiny fragments were placed in hot water with a temperature between 53 and 80 °C, and the extent to which they melted was observed. Both the float and melting point tests were then repeated using intact mothballs. Three emergency physicians blinded to the identities of samples and solutions visually evaluated each sample. In the float tests, paradichlorobenzene powder partially floated and partially sank in all three liquids, while naphthalene powder partially floated and partially sank in water. Naphthalene powder did not sink in D50 or saturated salt solution. Camphor powder floated in all three liquids. Float tests identified the compositions of intact mothball accurately. In the melting point tests, paradichlorobenzene powder melted completely in hot water within 1 min while naphthalene powder and camphor powder did not melt. The melted portions of paradichlorobenzene mothballs were sometimes too small to be observed in 1 min but the mothballs either partially or completely melted in 5 min. Both camphor and naphthalene intact mothballs did not melt in hot water. For mothball powder, the melting point tests were more accurate than the float tests in differentiating between paradichlorobenzene and non-paradichlorobenzene (naphthalene or camphor). For intact mothballs, float tests performed better than melting point tests. Float tests can identify camphor mothballs but melting point tests cannot. We suggest melting point tests for identifying mothball powder and tiny fragments while float tests are recommended for intact mothball and large fragments.

Evidence for large compositional ranges in coeval melts erupted from Kīlauea's summit reservoir: Chapter 7

USGS Publications Warehouse

Helz, Rosalind T.; Clague, David A.; Mastin, Larry G.; Rose, Timothy R.; Carey, Rebecca; Cayol, Valérie; Poland, Michael P.; Weis, Dominique

2015-01-01

Petrologic observations on Kīlauea's lavas include abundant microprobe analyses of glasses, which show the range of melts available in Kīlauea's summit reservoir over time. During the past two centuries, compositions of melts erupted within the caldera have been limited to MgO = 6.3–7.5 wt%. Extracaldera lavas of the 1959, 1971, and 1974 eruptions contain melts with up to 10.2, 8.9, and 9.2 wt% MgO, respectively, and the 1924 tephra contains juvenile Pele's tears with up to 9.1 wt% MgO. Melt compositions from explosive deposits at Kīlauea, including the Keanakāko‘i (A.D. 1500–1800), Kulanaokuaiki (A.D. 400–1000), and Pāhala (10–25 ka) tephra units, show large ranges of MgO contents. The range of melt MgO is 6.5–11.0 wt% for the Keanakāko‘i; the Kulanaokuaiki extends to 12.5% MgO and the Pāhala Ash includes rare shards with 13–14.5% MgO. The frequency distributions for MgO in the Keanakāko‘i and Kulanaokuaiki glasses are bimodal, suggesting preferential magma storage at two different depths. Kīlauea's summit reservoir contains melts ranging from 6.5 to at least 11.0 wt% MgO, and such melts were available for sampling near instantaneously and repeatedly over centuries. More magnesian melts are inferred to have risen directly from greater depth.

Nepheline structural and chemical dependence on melt composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marcial, José; Crum, Jarrod; Neill, Owen

Nepheline crystallizes upon slow-cooling in some melts concentrated in Na2O and Al2O3, which can result in a residual glass phase of low chemical durability. Nepheline can incorporate many components often found in high-level waste radioactive borosilicate glass, including glass network ions (e.g., Si, Al, Fe), alkali metals (e.g., Cs, K, Na, and possibly Li), alkaline-earth metals (e.g., Ba, Sr, Ca, Mg), and transition metals (e.g., Mn, and possibly Cr, Zn, Ni). When crystallized from melts of different compositions, nepheline chemistry varies as a function of starting glass composition. Five simulated high level nuclear waste borosilicate glasses shown to crystallize largemore » fractions of nepheline on slow cooling, were selected for study. These melts constituted a range of Al2O3, B2O3, CaO, Na2O, K2O, Fe2O3, and SiO2 compositions. Compositional analyses of nepheline crystals in glass by electron probe micro-analysis (EPMA) indicate that boron is unlikely to be present in any significant concentration, if at all, in nepheline. Also, several models are presented for calculating the fraction of vacancies in the nepheline structure.« less

The parent magma of the nakhlite meteorites - Clues from melt inclusions

NASA Technical Reports Server (NTRS)

Harvey, Ralph P.; Mcsween, Harry Y., Jr.

1992-01-01

Several forms of trapped liquid found within nakhlite meteorites have been examined, including interstitial melt and magmatic inclusions within the cores of large olivine grains. Differences in the mineralogy and texture between two types of trapped melt inclusions, and between these inclusions and the mesostasis, indicate that vitrophyric inclusions are most appropriate for estimating the composition of a nakhlite parental magma in equilibrium with early-forming olivine and augite. Parent liquids were calculated from the mineralogy of large inclusions in Nakhla and Governador Valadares, using a system of mass-balance equations solved by linear regression methods. The chosen parental liquids were cosaturated in olivine and augite and had Mg/Fe values consistent with measured augite/liquid Kds. These parental magma compositions are similar to other published compositions for Nakhla, Chassigny, and Shergotty parental melts, and may correspond to a significant magma type on Mars.

Preparation and Properties of a Novel Microcrystalline Cellulose-Filled Composites Based on Polyamide 6/High-Density Polyethylene

PubMed Central

Xu, Shihua; Yi, Shunmin; He, Jun; Wang, Haigang; Fang, Yiqun; Wang, Qingwen

2017-01-01

In the present study, lithium chloride (LiCl) was utilized as a modifier to reduce the melting point of polyamide 6 (PA6), and then 15 wt % microcrystalline cellulose (MCC) was compounded with low melting point PA6/high-density polyethylene (HDPE) by hot pressing. Crystallization analysis revealed that as little as 3 wt % LiCl transformed the crystallographic forms of PA6 from semi-crystalline to an amorphous state (melting point: 220 °C to none), which sharply reduced the processing temperature of the composites. LiCl improved the mechanical properties of the composites, as evidenced by the fact that the impact strength of the composites was increased by 90%. HDPE increased the impact strength of PA6/MCC composites. In addition, morphological analysis revealed that incorporation of LiCl and maleic anhydride grafted high-density polyethylene (MAPE) improved the interfacial adhesion. LiCl increased the glass transition temperature of the composites (the maximum is 72.6 °C). PMID:28773169

Nd, Sr and Pb isotopic composition of metasomatised xenoliths from the backarc Patagonian Mantle Wedge: Insights into the origin of the uprising melts

NASA Astrophysics Data System (ADS)

Zanetti, Alberto; Mazzucchelli, Maurizio; Hemond, Christope; Cipriani, Anna; Bertotto, Gustavo W.; Cingolani, Carlos; Vannucci, Riccardo

2010-05-01

Information about the geochemical composition of metasomatic melts migrating through the Patagonian mantle wedge is provided by the ultramafic xenoliths occurrence of Tres Lagos (TL; lat. 49.13°S, long. 71.18°W), Argentina. Such a locality is placed at the eastern border of the Meseta de la Muerte backarc basaltic plateau, where a post-plateau volcanic diatreme contains mantle xenoliths in both pyroclastites and lavas. Its latitude corresponds with the Northern limit of the Austral Volcanic Arc (AVZ), which is separated from the Southern Volcanic Zone (SVZ) by a gap in the arc magmatism ranging between 49° and 46°30' latitude S. The analysed xenoliths have been distinguished into two groups (Group 1 & 2). Group 1 consists of lherzolites and harzburgites, whereas Group 2 is formed by harzburgites. The texture of the Group 1 lherzolites varies from protogranular to granoblastic to porphyroblastic, whereas Group 1 harzburgites have always granoblastic texture. Group 2 harzburgites have granular texture, which may change to porphyroblastic owing to the random concentration of large olivine and orthopyroxene crystals. The clinopyroxenes (Cpx) from Group 1 lherzolites have PM-normalised REE patterns ranging from LREE-depleted (LaN/SmN= 0.24-0.37), to LREE-enriched (LaN/YbN up to 4.08) and spoon-shaped: the latter have minimum at Pr and Pr-Yb concentrations similar to those shown by the LREE-depleted Cpx. The Cpx from Group 1 harzburgites have lower REE concentrations with respect to the lherzolite ones and their REE patterns vary from HREE-enriched, steadily fractionated, (LaN/YbN = 0.21-0.35, Ybn ~ 1-2) to spoon-shaped (LaN/SmN = 2.81; SmN/YbN = 0.89; YbN ~ 3. The Cpx from the Group 2 harzburgites have convex-upward (LaN/SmN = 0.31; SmN/YbN = 1.50) to LREE-enriched (LaN/YbN = 2.94) patterns. The Sr, Nd and Pb isotopic compositions of the Group 1 clinopyroxenes form arrays spanning from DM to the field delimited by the TL basaltic lavas, pointing to EMI end-member. Conversely, Group 2 Cpx have much more radiogenic Sr and less radiogenic Nd values, approaching more closely the EMI and EMII end-members: these features are associated to unradiogenic lead isotopic compositions (206Pb/204Pb = 17.4-18.1; 207Pb/204Pb = 15.55-15.60; 208Pb/204Pb = 37.3-38.5). The combination of petrographic, trace element and isotopic features indicate that TL harzburgites are likely residua after melt-assisted partial melting triggered by melt/fluid migration in the hottest, and perhaps deeper, parts of the pristine DM lithosphere. The interpretation of the Pb, Sr and Nd isotope composition of Group 2 Cpx is not trivial. In analogy with the interpretation proposed for SWIR, it could unravel the occurrence of mantle sources which incorporated ancient crust and failed to homogenise with the DM mantle. Alternatively, it could be the evidence for ancient continental crust of the South America plate dragged down into the mantle by slab motion.

Liquid-liquid phase transformations and the shape of the melting curve.

PubMed

Makov, G; Yahel, E

2011-05-28

The phase diagram of elemental liquids has been found to be surprisingly rich, including variations in the melting curve and transitions in the liquid phase. The effect of these transitions in the liquid state on the shape of the melting curve is analyzed. First-order phase transitions intersecting the melting curve imply piecewise continuous melting curves, with solid-solid transitions generating upward kinks or minima and liquid-liquid transitions generating downward kinks or maxima. For liquid-liquid phase transitions proposed for carbon, phosphorous selenium, and possibly nitrogen, we find that the melting curve exhibits a kink. Continuous transitions imply smooth extrema in the melting curve, the curvature of which is described by an exact thermodynamic relation. This expression indicates that a minimum in the melting curve requires the solid compressibility to be greater than that of the liquid, a very unusual situation. This relation is employed to predict the loci of smooth maxima at negative pressures for liquids with anomalous melting curves. The relation between the location of the melting curve maximum and the two-state model of continuous liquid-liquid transitions is discussed and illustrated by the case of tellurium. © 2011 American Institute of Physics

Geochemical Comparison of Four Cores from the Manson Impact Structure

NASA Technical Reports Server (NTRS)

Korotev, Randy L.; Rockow, Kaylynn M.; Jolliff, Bradley L.; Haskin, Larry A.; McCarville, Peter; Crossey, Laura J.

1996-01-01

Concentrations of 33 elements were determined in relatively unaltered, matrix-rich samples of impact breccia at approximately 3-m-depth intervals in the M-1 core from the Manson impact structure, Iowa. In addition, 46 matrix-rich samples from visibly altered regions of the M-7, M-8, and M-10 cores were studied, along with 42 small clasts from all four cores. Major element compositions were determined for a subset of impact breccias from the M-1 core, including matrix-rich impact-melt breccia. Major- and trace-element compositions were also determined for a suite of likely target rocks. In the M-1 core, different breccia units identified from lithologic examination of cores are compositionally distinct. There is a sharp compositional discontinuity at the boundary between the Keweenawan-shale-clast breccia and the underlying unit of impact-melt breccia (IMB) for most elements, suggesting minimal physical mixing between the two units during emplacement. Samples from the 40-m-thick IMB (M-1) are all similar to each other in composition, although there are slight increases in concentration with depth for those elements that have high concentrations in the underlying fragmental-matrix suevite breccia (SB) (e.g., Na, Ca, Fe, Sc), presumably as a result of greater clast proportions at the bottom margin of the unit of impact-melt breccia. The high degree of compositional similarity we observe in the impact-melt breccias supports the interpretation that the matrix of this unit represents impact melt. That our analyses show such compositional similarity results in part from our technique for sampling these breccias: for each sample we analyzed a few small fragments (total mass: approximately 200 mg) selected to be relatively free of large clasts and visible signs of alteration instead of subsamples of powders prepared from a large mass of breccia. The mean composition of the matrix-rich part of impact-melt breccia from the M-1 core can be modeled as a mixture of approximately 35% shale and siltstone (Proterozoic "Red Clastics"), 23% granite, 40% hornblende-biotite gneiss, and a small component (less than 2%) of mafic-dike rocks.

Effect of a Nonplanar Melt-Solid Interface On Lateral Compositional Distribution During Unidirectional Solidification of a Binary Alloy with a Constant Growth Velocity V. Pt. 1; Theory

NASA Technical Reports Server (NTRS)

Wang, Jai-Ching; Watring, D.; Lehoczky. S. L.; Su, C. H.; Gillies, D.; Szofran, F.; Sha, Y. G.; Sha, Y. G.

1999-01-01

Infrared detected materials, such as Hg(1-x)Cd(x)Te, Hg(1-x)Zn(x)Te have energy gaps almost linearly proportional to their composition. Due to the wide separation of liquidus and solidus curves of their phase diagram, there are compositional segregation in both of the axial and radial directions of these crystals grown in the Bridgman system unidirectionally with constant growth rate. It is important to understand the mechanisms, which affect lateral segregation such that large radially uniform composition crystal can be produced. Following Coriel, etc's treatment, we have developed a theory to study the effect of a curved melt-solid interface shape on lateral composition distribution. The model is considered to be a cylindrical system with azimuthal symmetry and a curved melt-solid interface shape which can be expressed as a linear combination of a series of Bessell's functions. The results show that melt-solid interface shape has a dominant effect on the lateral composition distribution of these systems. For small values of beta, the solute concentration at the melt-solid interface scales linearly with interface shape with a proportional constant of the produce of beta and (1 -k), where beta = VR/D, with V as growth velocity, R as the sample radius, D as the diffusion constant and k as the distribution constant. A detailed theory will be presented. A computer code has been developed and simulations have been performed and compared with experimental results. These will be published in another paper.

Effect of a Nonplanar Melt-Solid Interface on Lateral Compositional Distribution during Unidirectional Solidification of a Binary Alloy with a Constant Growth Velocity V. Part 1; Theory

NASA Technical Reports Server (NTRS)

Wang, Jai-Ching; Watring, Dale A.; Lehoczky, Sandor L.; Su, Ching-Hua; Gillies, Don; Szofran, Frank

1999-01-01

Infrared detector materials, such as Hg(1-x)Cd(x)Te, Hg(1-x)Zn(x)Te have energy gaps almost linearly proportional to its composition. Due to the wide separation of liquidus and solidus curves of their phase diagram, there are compositional segregations in both of axial and radial directions of these crystals grown in the Bridgman system unidirectionally with constant growth rate. It is important to understand the mechanisms which affect lateral segregation such that large uniform radial composition crystal is possible. Following Coriell, etc's treatment, we have developed a theory to study the effect of a curved melt-solid interface shape on the lateral composition distribution. The system is considered to be cylindrical system with azimuthal symmetric with a curved melt-solid interface shape which can be expressed as a linear combination of a series of Bessell's functions. The results show that melt-solid interface shape has a dominate effect on lateral composition distribution of these systems. For small values of b, the solute concentration at the melt-solid interface scales linearly with interface shape with a proportional constant of the product of b and (1 - k), where b = VR/D, with V as growth velocity, R as sample radius, D as diffusion constant and k as distribution constant. A detailed theory will be presented. A computer code has been developed and simulations have been performed and compared with experimental results. These will be published in another paper.

Isotope and trace element insights into heterogeneity of subridge mantle

NASA Astrophysics Data System (ADS)

Mallick, Soumen; Dick, Henry J. B.; Sachi-Kocher, Afi; Salters, Vincent J. M.

2014-06-01

Geochemical data for abyssal peridotites are used to determine the relationship to mid-ocean ridge basalts from several locations at ridge segments on the SW Indian Ridge (SWIR), the Mid-Cayman-Rise (MCR), and the Mid-Atlantic Ridge (MAR). Based on chemical and petrological criteria peridotites are categorized as being either dominantly impregnated with melt or being residual after recent melting. Those that are considered impregnated with melt also have isotopic compositions similar to the basalts indicating impregnation by an aggregate MORB melt. A SWIR and MCR residual peridotite Nd-isotopic compositions partly overlap the Nd-isotopic compositions of the basalts but extend to more radiogenic compositions. The differences between peridotite and basalt Nd-isotopic compositions can be explained by incorporating a low-solidus component with enriched isotopic signature in the subridge mantle: a component that is preferentially sampled by the basalts. At the MAR, peridotites and associated basalts have overlapping Nd-isotopic compositions, suggesting a more homogeneous MORB mantle. The combined chemistry and petrography indicates a complex history with several depletion and enrichment events. The MCR data indicate that a low-solidus component can be a ubiquitous component of the asthenosphere. Residual abyssal peridotites from limited geographic areas also show significant chemical variations that could be associated with initial mantle heterogeneities related to events predating the ridge-melting event. Sm-Nd model ages for possible earlier depletion events suggest these could be as old as 2.4 Ga. This article was corrected on 9 JULY 2014. See the end of the full text for details.

The partitioning of sulfur between multicomponent aqueous fluids and felsic melts

NASA Astrophysics Data System (ADS)

Binder, Bernd; Wenzel, Thomas; Keppler, Hans

2018-02-01

Sulfur partitioning between melt and fluid phase largely controls the environmental impact of volcanic eruptions. Fluid/melt partitioning data also provide the physical basis for interpreting changes in volcanic gas compositions that are used in eruption forecasts. To better constrain some variables that control the behavior of sulfur in felsic systems, in particular the interaction between different volatiles, we studied the partitioning of sulfur between aqueous fluids and haplogranitic melts at 200 MPa and 750-850 °C as a function of oxygen fugacity (Ni-NiO or Re-ReO2 buffer), melt composition (Al/(Na + K) ratio), and fluid composition (NaCl and CO2 content). The data confirm a first-order influence of oxygen fugacity on the partitioning of sulfur. Under "reducing conditions" (Ni-NiO buffer), D fluid/melt is nearly one order of magnitude larger (323 ± 14 for a metaluminous melt) than under "oxidizing conditions" (Re-ReO2 buffer; 74 ± 5 for a metaluminous melt). This effect is likely related to a major change in sulfur speciation in both melt and fluid. Raman spectra of the quenched fluids show the presence of H2S and HS- under reducing conditions and of SO4 2- and HSO4 - under oxidizing conditions, while SO2 is undetectable. The latter observation suggests that already at the Re-ReO2 buffer, sulfur in the fluid is almost completely in the S6+ state and, therefore, more oxidized than expected according to current models. CO2 in the fluid (up to x CO2 = 0.3) has no effect on the fluid/melt partitioning of sulfur, neither under oxidizing nor under reducing conditions. However, the effect of NaCl depends on redox state. While at oxidizing conditions, D fluid/melt is independent of x NaCl, the fluid/melt partition coefficient strongly decreases with NaCl content under reducing conditions, probably due to a change from H2S to NaSH as dominant sulfur species in the fluid. A decrease of D fluid/melt with alkali content in the melt is observed over the entire compositional range under reducing conditions, while it is prominent only between the peraluminous and metaluminous composition in oxidizing experiments. Overall, the experimental results suggest that for typical oxidized, silicic to intermediate subduction zone magmas, the degassing of sulfur is not influenced by the presence of other volatiles, while under reducing conditions, strong interactions with chlorine are observed. If the sulfur oxidation state is preserved during an explosive eruption, a large fraction of the sulfur released from oxidized magmas may be in the S6+ state and may remain undetected by conventional methods that only measure SO2. Accordingly, the sulfur yield and the possible climatic impact of some eruptions may be severely underestimated.

Temperature-profile detector

DOEpatents

Not Available

1981-01-29

Temperature profiles at elevated temperature conditions are monitored by use of an elongated device having two conductors spaced by the minimum distance required to normally maintain an open circuit between them. The melting point of one conductor is selected at the elevated temperature being detected, while the melting point of the other is higher. As the preselected temperature is reached, liquid metal will flow between the conductors creating short circuits which are detectable as to location.

Temperature profile detector

DOEpatents

Tokarz, Richard D.

1983-01-01

Temperature profiles at elevated temperature conditions are monitored by use of an elongated device having two conductors spaced by the minimum distance required to normally maintain an open circuit between them. The melting point of one conductor is selected at the elevated temperature being detected, while the melting point of the other is higher. As the preselected temperature is reached, liquid metal will flow between the conductors, creating short circuits which are detectable as to location.

Nuclear reactor melt arrest and coolability device

DOEpatents

Theofanous, Theo G.; Dinh, Nam Truc; Wachowiak, Richard M.

2016-06-14

Example embodiments provide a Basemat-Internal Melt Arrest and Coolability device (BiMAC) that offers improved spatial and mechanical characteristics for use in damage prevention and risk mitigation in accident scenarios. Example embodiments may include a BiMAC having an inclination of less than 10-degrees from the basemat floor and/or coolant channels of less than 4 inches in diameter, while maintaining minimum safety margins required by the Nuclear Regulatory Commission.

Does Change in the Arctic Sea Ice Indicate Climate Change? A Lesson Using Geospatial Technology

ERIC Educational Resources Information Center

Bock, Judith K.

2011-01-01

The Arctic sea ice has not since melted to the 2007 extent, but annual summer melt extents do continue to be less than the decadal average. Climate fluctuations are well documented by geologic records. Averages are usually based on a minimum of 10 years of averaged data. It is typical for fluctuations to occur from year to year and season to…

Physico-chemical transition from peridotite assemblage to the eclogite one (experimental data at 7.0 GPa).

NASA Astrophysics Data System (ADS)

Butvina, Valentina; Litvin, Yurii

2010-05-01

Peridotites and eclogites, including diamond-bearing ones, are the basic ultra-basic and basic rocks of the upper mantle (Ringwood, 1969, 1975; Sobolev, 1974; Marakushev, 1985; Taylor & Anand, 2004). These rocks are presented in the assemblage of mantle xenolyths in kimberlites, but the basic minerals of peridotite paragenesis, olivine, orthopyroxene, garnet and clinopyroxene as well as of an eclogite paragenesis, garnet and omphacite are wide-spread synthetic inclusions in diamonds. The cases of finding minerals and peridotite and eclogite parageneses in diamond are described. It implies that these parageneses can have a single mantle source. However, the formation of peridotite and eclogite mineral parageneses at differentiation of the primary ultrabasite melt during physico-chemical single process is possible only at overcoming the 'eclogite' thermal barrier (O'Hara, 1968; Litvin, 1991). Eclogite genesis is one of the most difficult and discussional problems of modern petrology. Among investigators there is an opinion about eclogite heterogeneity not only on conditions of formation (crust, mantle), but also by composition of the initial rocks (para-, orthoeclogites) as well as by the way of their formation (magmatic, metamorphic, metasomatic). In literature diamond-bearing eclogite nodules of kimberlite pipes are often considered as metamorphic, which are formed at subduction of the Archean or of the Proterozoic oceanic crust (MacGregor & Manton, 1986; McCandless & Gurney, 1986, 1997 et al.). Only the presence of Na2O in garnet and K2O in clinopyroxene is a criterion of their participation in mantle magmatic processes. Together with the hypotheses considered on eclogite origin there exists a version suggested in papers (Kushiro, 1972; Kushiro & Yoder, 1974), according to which mantle eclogites could be formed due to peridotite substance in the processes of fractional crystallization of ultrabasite magmas. The present paper is devoted to the experimental study of this problem. Physico-chemical transition from peridotite assemblage to the eclogite one can be only ensured by the processes of fractional crystallization of mantle magmatic melts. The primary melting and magmatic evolution of mantle garnet lerzolite (or the Ringwood pyrolite) is controlled by a five-phase peritectics 'p' Ol+Opx+Cpx+Grt+L and four cotectic curves conjugated to it (Litvin, 1991). In melting and evolution of melts of both olivine eclogites and coesite and corundum eclogites the corresponding five-phase eutectics are of a dominant importance. A general ridge for all elementary tetrahedrons (simplexes) is a line of compositions diopside-pyrope (clinopyroxene-garnet) which bimineral eclogite assemblages belong to. The internal section En-Di-Cor of the general tetrahendric diagram (symplex complex) separates olivine-saturated and silica-saturated compositions. 'Eclogite' thermal barrier is 'thermal barrier' on (O'Hara, 1968), on the cotectic line Opx+Cpx+Grt+L, connecting 'peridotite' peritectic and 'eclogite' eutectic points. Meanwhile, at equilibrium (and fractional) crystallization of peridotite system in the peritectic point 'p' orthopyroxene vanishes as a result of the peritectic reaction 'orthopyroxene + melt - clinopyroxene' (Davis, 1963; Litvin, 1991). With further temperature decrease the composition of the remnant melt is controlled by the nonorthopyroxene cotectics Ol+Cpx+Grt+L first, in the limits of the peridotite 'simplex', but then mechanism of fractional crystallization is also realized in the limits of the olivine-eclogite 'simplex' up to the corresponding nonvariant eutectics. The considered cotectics Ol+Cpx+Grt+L is of the greatest interest from the viewpoint of a possible change of compositions of remnant melts from olivine-normative to silica-normative ones. One can assume that under the conditions of fractional melt crystallization along the cotectic curve Ol+Cpx+Grt+L together with olivine jigging accumulation of incorehent elements, including Na, Fe etc. takes place. It leads to a gradual increase of jadeite component content in remnant melts what creates grounds for reactional interaction of jadeite and olivine components with olivine vanishing and garnet formation in accordance with the reaction found in (Litvin et al., 2004). A gradual decrease of olivine component content in remnant melts caused by that fact realizes a 'turn' to the cotectic curve Ol+Cpx+Grt+L in the direction of the boundary section En - Di - Cor and, probably its exit to the line Di-Prp (clinopyroxene-garnet). Further under the conditions of fractional crystallization melt composition point can penetrate into the volumes of coesite-eclogite, kyanite-eclogite and corundum-eclogite 'symplexes'. Thus, an overcoming of 'eclogite' thermal barrier between olivine-normative peridotite-pyroxene and SiO2 - normative eclogite compositions occurs. So, one can speak about the 'destruction' of liquidus peridotite-eclogite thermal barrier in the limits of the peridotite 'simplex' as a result of realization of two reaction mechanisms: (1) vanishing of orthopyroxene as a result of its peritectic reaction with the melt with clinopyroxene formation and (2) olivine vanishing as a result of its reactional interaction of jadeite with garnet formation. If with respect to the first mechanism definite experimental evidence exists (Litvin, 1991; Davis, 1963) then for the second mechanism it is absent. Due to this fact the main purpose of this paper is an experimental study of phase relationships in the model system forsterite-dioside-jadeite at pressure of 7 GPa and foundation of possible physico-chemical correct transitions between peridotite and eclogite parageneses with overcoming liquidus 'eclogite' thermal barrier. To construct a diagram of a ternary system forsterite-diopside-jadeite it is necessary to study its boundary binary sections forsterite-jadeite and fosterite-diopside as well as a number of internal polythermic sections. The section jadeite-diopside at 7 GPa has been studied earlier (Bobrov, Litvin, Kojitani, Akaogi, 2006; 2008) and it is characterized by the unlimited miscibility of jadeite and diopside components in solid and liquid states. The first experimental results obtained at the initial stage of the investigation of this problem can be characterized as follows. For the experimental study polythermic sections of forsterite-(jadeite50diopside50) and forsterite-(jadeite25diopside75) have been chosen. The obtained data testify to the fact that olivine vanishing and garnet formation are realized in both sections. The problem of further investigations is to search minimum concentrations of jadeite in the composition of this system where a total olivine vanishing takes place. Thus, the performed experimental investigations of the model system forsterite-diospside-jadeite at pressure 7 GPa testify to the fact that forsterite (olivine) is a stable phase in the boundary system forsterite-diopside (olivine-clinopyroxene). While introducing rather low contents of jadeite component into the composition of this system the reaction of jadeite component with forsterite takes place in the melt. As a result, garnet appears as liquidus phase.

Assimilation by Lunar Mare Basalts: Melting of Crustal Material and Dissolution of Anorthite

NASA Technical Reports Server (NTRS)

Finnila, A. B.; Hess, P. C.; Rutherford, M. J.

1994-01-01

We discuss techniques for calculating the amount of crustal assimilation possible in lunar magma chambers and dikes based on thermal energy balances, kinetic rates, and simple fluid mechanical constraints. Assuming parent magmas of picritic compositions, we demonstrate the limits on the capacity of such magmas to melt and dissolve wall rock of anorthitic, troctolitic, noritic, and KREEP (quartz monzodiorite) compositions. Significant melting of the plagioclase-rich crustal lithologies requires turbulent convection in the assimilating magma and an efficient method of mixing in the relatively buoyant and viscous new melt. Even when this occurs, the major element chemistry of the picritic magmas will change by less than 1-2 wt %. Diffusion coefficients measured for Al2O3 from an iron-free basalt and an orange glass composition are 10(exp -12) m(exp 2) s(exp -1) at 1340 C and 10(exp -11) m(exp 2) s(exp -1) at 1390 C. These rates are too slow to allow dissolution of plagioclase to significantly affect magma compositions. Picritic magmas can melt significant quantities of KREEP, which suggests that their trace element chemistry may still be affected by assimilation processes; however, mixing viscous melts of KREEP composition with the fluid picritic magmas could be prohibitively difficult. We conclude that only a small part of the total major element chemical variation in the mare basalt and volcanic glass collection is due to assimilation/fractional crystallization processes near the lunar surface. Instead, most of the chemical variation in the lunar basalts and volcanic glasses must result from assimilation at deeper levels or from having distinct source regions in a heterogeneous lunar mantle.

Carbonatitic liquids and COH fluids from epidote-dolomite eclogites at 3.7 - 4.6 GPa: new perspectives on carbon transfer at subduction zones

NASA Astrophysics Data System (ADS)

Poli, S.

2013-12-01

Current knowledge on the solidus temperature for carbonate-bearing rocks suggests that carbonatitic liquids should not form in a subducted oceanic lithosphere, unless anomalous thermal relaxation occurs. For a mildly warm subduction path, COH-bearing basaltic eclogites are expected to loose all H2O component at epidote breakdown, located at approx. 2.8-3.0 GPa. Above this pressure limit, the solidus is that of a carbonated basaltic eclogite which shows a minimum temperature of 1020 °C at 4.0-4.5 GPa (Dasgupta et al. 2004). However, the oceanic crust includes a range of gabbroic rocks, altered on rifts and transforms, with large amounts of An-rich plagioclase. It has been shown that epidote disappearance with pressure depend on the normative anorthite content of the bulk composition considered (Poli et al. 2009); we therefore expect that altered gabbros might display a much wider pressure range where epidote persists, potentially affecting the solidus relationships. Notably, this applies to epidosite rocks formed in hydrothermal environments at oceanic settings, then recovered in high-pressure and ultra-high pressure terrains. New experimental data from 3.7 to 4.6 GPa, 750°C to 1000 °C are intended to unravel the effect of variable bulk and volatile compositions in model eclogites, enriched in the normative anorthite component (An37 and An45). Experiments are performed in piston cylinder and multianvil machines apparatus, using both single and, buffered, double capsule techniques. Garnet, clinopyroxene and coesite form in all syntheses. Lawsonite was found to persist at 3.7 GPa, 750 °C, with both dolomite and magnesite; at 3.8 GPa, 775-800 °C, fluid saturated conditions, epidote coexists with kyanite, dolomite and magnesite. The anhydrous assemblage garnet, omphacite, aragonite, kyanite is found at 4.2 GPa, 850 °C. At 900 °C, fluid-rich conditions, a silicate fluid/melt of granitoid composition, a carbonatitic melt and Na-carbonate are observed. Close to fluid-saturation, 3.8-4.2 GPa, 900 °C, garnet and Na-rich clinopyroxene coexist with a carbonatitic melt and dolomite. The carbonatitic melt is richer in Ca compared to dolomite, consistently with phase relationships in the model system MgCO3-FeCO3-CaCO3. In fluid-undersaturated compositions, fluid-absent melting of epidote + dolomite, enlarged in its pressure stability for An-rich gabbros, is expected to promote the generation of carbonatitic liquids. The subsolidus breakdown of epidote in the presence of carbonates at depths exceeding 120 km provides a major source of COH fluids at subarc depth. In warm subduction zones, the possibility of extracting carbonatitic liquids from a variety of gabbroic rocks and epidosites offers new scenarios on the metasomatic processes in the lithospheric wedge of subduction zones and a new mechanism for recycling carbon. Dasgupta R., Hirschmann M.M., Withers A. (2004) Earth Planet Sci Lett, 227: 73-85 Poli S., Franzolin E., Fumagalli P., Crottini A. (2009) Earth Planet Sci Lett, 278: 350-360

Lithological, Chemical and Chronological Constraints on Melt Extraction from the Mantle Section of the ~492 Ma Shetland Ophiolite Complex, Scotland

NASA Astrophysics Data System (ADS)

O'Driscoll, B.; Walker, R. J.; Clay, P. L.; Day, J. M.; Ash, R. D.; Daly, J. S.

2015-12-01

The mantle sections of ophiolites offer a means of studying the composition and structure of the oceanic mantle. In particular, the relations between different lithologies can be established in the field, permitting an assessment of the relative timing of processes such as melt extraction and melt-rock reaction. The Shetland Ophiolite Complex (SOC) contains a well-preserved mantle section that is dominated by harzburgite (≥70 vol.%), with dominantly chondritic present-day 187Os/188Os compositions1. Melt extraction and melt-rock reaction is evident in the form of dunite and chromitite layers and lenses, with thicknesses ranging from millimetres-to-metres. These lithologies are characteristic of supra-subduction zone processing and are considered to relate to closure of the Iapetus Ocean at ~492 Ma1. However, evidence of much earlier melt extraction has been suggested for some SOC harzburgites, which have relatively unradiogenic 187Os/188Os compositions that yield TRD model ages as old as ~1.4 Ga1. In order to assess the scales at which such compositional heterogeneities are preserved in the mantle, a small (45 m2) area of the SOC mantle section was selected for detailed lithological mapping and sampling. A selection of harzburgites (n=8), dunites (n=6) and pyroxenites (n=2) from this area has been analysed for their Os isotope and highly-siderophile element (HSE) compositions. Six of the harzburgites and four of the dunites have relative HSE abundances and gOs values that are approximately chondritic, with gOs ranging only from -0.6 to +2.7 (n=10). Two dunites have more radiogenic gOs (up to +7.5), that is correlated with enhanced concentrations of accessory base-metal sulphides, suggesting formation via melt percolation and melt-rock reaction. The two remaining harzburgites have less radiogenic gOs (-3.5 and -4), yielding Mesoproterozoic TRD ages. The new data indicate that a comparable range of Os isotope compositions to that previously measured across the entire SOC mantle section is present in the mapped area, i.e., at the m2 scale, revealing the modest scale of isotopic and chemical heterogeneity in the oceanic mantle. 1O'Driscoll B, Day JMD, Walker RJ, Daly JS, McDonough WF, Piccoli PM (2012). Earth and Planetary Science Letters 333-334: 226-237.

Chromium isotope heterogeneity in the mantle

NASA Astrophysics Data System (ADS)

Xia, Jiuxing; Qin, Liping; Shen, Ji; Carlson, Richard W.; Ionov, Dmitri A.; Mock, Timothy D.

2017-04-01

To better constrain the Cr isotopic composition of the silicate Earth and to investigate potential Cr isotopic fractionation during high temperature geological processes, we analyzed the Cr isotopic composition of different types of mantle xenoliths from diverse geologic settings: fertile to refractory off-craton spinel and garnet peridotites, pyroxenite veins, metasomatised spinel lherzolites and associated basalts from central Mongolia, spinel lherzolites and harzburgites from North China, as well as cratonic spinel and garnet peridotites from Siberia and southern Africa. The δ53CrNIST 979 values of the peridotites range from - 0.51 ± 0.04 ‰ (2SD) to + 0.75 ± 0.05 ‰ (2SD). The results show a slight negative correlation between δ53Cr and Al2O3 and CaO contents for most mantle peridotites, which may imply Cr isotopic fractionation during partial melting of mantle peridotites. However, highly variable Cr isotopic compositions measured in Mongolian peridotites cannot be caused by partial melting alone. Instead, the wide range in Cr isotopic composition of these samples most likely reflects kinetic fractionation during melt percolation. Chemical diffusion during melt percolation resulted in light Cr isotopes preferably entering into the melt. Two spinel websterite veins from Mongolia have extremely light δ53Cr values of - 1.36 ± 0.04 ‰ and - 0.77 ± 0.06 ‰, respectively, which are the most negative Cr isotopic compositions yet reported for mantle-derived rocks. These two websterite veins may represent crystallization products from the isotopically light melt that may also metasomatize some peridotites in the area. The δ53Cr values of highly altered garnet peridotites from southern Africa vary from - 0.35 ± 0.04 ‰ (2SD) to + 0.12 ± 0.04 ‰ (2SD) and increase with increasing LOI (Loss on Ignition), reflecting a shift of δ53Cr to more positive values by secondary alteration. The Cr isotopic composition of the pristine, fertile upper mantle is estimated as δ53Cr = - 0.14 ± 0.12 ‰, after corrections for the effects of partial melting and metasomatism. This value is in line with that estimated for the BSE (- 0.12 ± 0.10 ‰) previously.

Origin and Role of Recycled Crust in Flood Basalt Magmatism: Case Study of the Central East Greenland Rifted Margin

NASA Astrophysics Data System (ADS)

Brown, E.; Lesher, C. E.

2015-12-01

Continental flood basalts (CFB) are extreme manifestations of mantle melting derived from chemically/isotopically heterogeneous mantle. Much of this heterogeneity comes from lithospheric material recycled into the convecting mantle by a range of mechanisms (e.g. subduction, delamination). The abundance and petrogenetic origins of these lithologies thus provide important constraints on the geodynamical origins of CFB magmatism, and the timescales of lithospheric recycling in the mantle. Basalt geochemistry has long been used to constrain the compositions and mean ages of recycled lithologies in the mantle. Typically, this work assumes the isotopic compositions of the basalts are the same as their mantle source(s). However, because basalts are mixtures of melts derived from different sources (having different fusibilities) generated over ranges of P and T, their isotopic compositions only indirectly represent the isotopic compositions of their mantle sources[1]. Thus, relating basalts compositions to mantle source compositions requires information about the melting process itself. To investigate the nature of lithologic source heterogeneity while accounting for the effects of melting during CFB magmatism, we utilize the REEBOX PRO forward melting model[2], which simulates adiabatic decompression melting in lithologically heterogeneous mantle. We apply the model to constrain the origins and abundance of mantle heterogeneity associated with Paleogene flood basalts erupted during the rift-to-drift transition of Pangea breakup along the Central East Greenland rifted margin of the North Atlantic igneous province. We show that these basalts were derived by melting of a hot, lithologically heterogeneous source containing depleted, subduction-modified lithospheric mantle, and <10% recycled oceanic crust. The Paleozoic mean age we calculate for this recycled crust is consistent with an origin in the region's prior subduction history, and with estimates for the mean age of recycled crust in the modern Iceland plume[3]. These results suggest that this lithospheric material was not recycled into the lower mantle before becoming entrained in the Iceland plume. [1] Rudge et al. (2013). GCA, 114, p112-143; [2] Brown & Lesher (2014). Nat. Geo., 7, p820-824; [3] Thirlwall et al. (2004). GCA, 68, p361-386

Mantle melting and melt refertilization beneath the Southwest Indian Ridge: Mineral composition of abyssal peridotites

NASA Astrophysics Data System (ADS)

Chen, Ling; Zhu, Jihao; Chu, Fengyou; Dong, Yan-hui; Liu, Jiqiang; Li, Zhenggang; Zhu, Zhimin; Tang, Limei

2017-04-01

As one of the slowest spreading ridges of the global ocean ridge system, the Southwest Indian Ridge (SWIR) is characterized by discontinued magmatism. The 53°E segment between the Gallieni fracture zone (FZ) (52°20'E) and the Gazelle FZ (53°30'E) is a typical amagmatic segment (crustal thickness <2km) (Zhou and Dick, 2013) that opens a window to the mantle thus provides a chance to detect the mantle composition directly. We examine the mineral compositions of 17 peridotite samples from the 53°E amagmatic segment. The results show that the peridotites can be divided into two groups. The Group 1 peridotites are characterized by clinopyroxenes having LREE depleted patterns that is typical for the abyssal peridotite, thus are thought to be the residue of the mantle melting. The Group 2 peridotites show the lowest HREE content within the SWIR peridotites but are anomaly enriched in LREE, with flat or U-type REE patterns, thus cannot be the pure residue of mantle melting. Mineral compositions of the Group 2 peridotites are more depleted than that of peridotites sampled near the Bouvet hot spot (Johnson et al., 1990), implying that the depleted mantle beneath the 53°E segment may be the residue of ancient melting event. This hypothesis is supported by the the low Ol/Opx ratios, coarse grain sizes (>1cm) Opx, and Mg-rich mineral compositions akin to harzburgite xenoliths that sample old continental lithospheric mantle (Kelemen et al., 1998). Melt refertilization model shows that Group 2 peridotites were affected by an enriched low-degree partial melt from the garnet stability field. These results indicate that depleted mantle which experiences ancient melting event are more sensitive to melt refertilization, thus may reduce the melt flux, leading to extremely thin crust at 53°E segment. This research was granted by the National Basic Research Programme of China (973 programme) (grant No. 2013CB429705) and the Fundamental Research Funds of Second Institute of Oceanography, State Oceanic Administration (JG1603, SZ1507). References: Johnson K T M, Dick H J B, Shimizu N. Melting in the oceanic upper mantle: An ion microprobe study of diopsides in abyssal peridotites[J]. Journal of Geophysical Research, 1990, 95(B3):2661-2678. Kelemen P B, Hart S R, Bernstein S. Silica enrichment in the continental upper mantle via melt/rock reaction[J]. Earth & Planetary Science Letters, 1998, 164(1-2):387-406. Zhou H, Dick H J. Thin crust as evidence for depleted mantle supporting the Marion Rise.[J]. Nature, 2013, 494(7436):195-200.

Syntectic Reactions involving Limestones and Limestone-Derived Carbonatitic Melts in the Generation of some Peralkalic Magmas: Reflections on Reginald Daly's Insights 100 Years Later

NASA Astrophysics Data System (ADS)

Lentz, D.

2017-12-01

The theoretical analysis of how sedimentary limestones and marbles could melt as a result of infiltrative contact metasomatism associated with silicate magmas, enables reconsideration of the limestone syntectic (assimilation) hypothesis for the origin of some peralkalic rocks. Reginald Daly's syntectic model published in detail in early 1918 fell out of favor because experimental evidence from the early 1960's suggested; 1) that limestone assimilation would increase P(CO2) and cause solidification of the silicate intrusion, 2) that there is a thermal barrier between silica-saturated and undersaturated magmas that would inhibit extensive desilication of the magma, and 3) the endothermic decarbonation reactions would require heat via magmatic crystallization of near-solidus magmas. However, these concerns were not as critical for high-T mafic melts relative to more low-T silicic melts, although most subsequent researchers dismissed syntexis as isotopic arguments also seemed robust. However, skarn-related limestone melts can interact much more easily with silicate magma, resulting in calc-silicate-forming (endoskarn-like) limestone syntectic (desilication - calcification-magnesification processes) decarbonation reactions with compositional evolution into the silica-undersaturated field. If mafic in composition originally when syntectically modified, then the CO2-bearing derivative peralkalic melt may subsequently react with the dominant volume magma or fractionate separately into a more evolved composition. As well, an increase in P(CO2) within the modified silicate fraction coupled with compositional evolution to more silica-undersaturated compositions enhances the stability of the immiscible, extremely low viscosity carbonate melt fraction. In addition, dynamic interaction of these co-existing immiscible melts (analogous to the current hypothesis) would partition elements, as well as isotopic signatures, such that they would be virtually unrecognizable as having a crustal level syntectic origin, based on mass-balance principles and Rayleigh decarbonation isotopic equilibria, as they do in many infiltrative skarn systems. Essentially, this partly vindicates the basic premise of Daly's limestone syntectic hypothesis for the origin of some peralkalic igneous rocks.

Evidence for a homogeneous primary magma at Piton de la Fournaise (La Réunion): A geochemical study of matrix glass, melt inclusions and Pélé's hairs of the 1998-2008 eruptive activity

NASA Astrophysics Data System (ADS)

Villemant, B.; Salaün, A.; Staudacher, T.

2009-07-01

Magmas erupted at Piton de la Fournaise volcano since 0.5 Ma, display a large petrological and chemical range (picrites, 2 types of transitional basalts and differentiated magmas) and low amplitude isotopic heterogeneities. The recent activity (1998-2008) includes all magma types except evolved magmas. Matrix glass compositions from quenched lavas and Pélé's hairs of the whole 1998-2008 period define a single differentiation trend from a common basaltic melt (MgO ~ 9%) for the first time identified in the 2007 magmas. More primitive melt compositions (MgO ~ 12.5%) are only evidenced by olivine crystals with high Fo contents (Fo 85-88.4). Evolutions of major and trace element of glass and mineral compositions are consistently modelled by a unique low pressure crystal fractionation process. The composition range of olivine melt inclusions is distinct from that of matrix glass and Pélé's hair and corresponds to equilibrium crystallisation in closed system of melts trapped from the main differentiation series at high temperature. The range of basaltic types at Piton de la Fournaise is the result of large variations in the differentiation degree (10 to 35% crystallisation) of a single primary basaltic melt and the addition in highly variable amounts (up to 50% in picrites) of co-genetic olivine or gabbroic cumulates. These cumulates may represent the shallow and dense bodies identified by seismic tomography and have likely been produced by the repetitive intrusion and differentiation of basalts along Piton de la Fournaise history. Depending on the shallow transfer paths, ascending magmas may disaggregate and incorporate various types of cumulates, explaining all particular features of basaltic magmas and picrites. These results emphasize the exceptional chemical homogeneity of the primary basaltic melt and of the differentiation process involved in volcanic activity of La Réunion hotspot since 0.5 Ma and the increasingly recognised role of melt-wall rock interactions in compositional and petrological diversity of erupted magmas.

Meltable magnetic biocomposites for controlled release

NASA Astrophysics Data System (ADS)

Müller, R.; Zhou, M.; Dellith, A.; Liebert, T.; Heinze, T.

2017-06-01

New biocompatible composites with adjustable melting point in the range of 30-140 °C, consisting of magnetite nanoparticles embedded into a matrix of meltable dextran fatty acid ester are presented which can be softened under an induced alternating magnetic field (AMF). The chosen thermoplastic magnetic composites have a melting range close to human body temperature and can be easily shaped into disk or coating film under melting. The composite disks were loaded with green fluorescent protein (GFP) as a model protein. Controlled release of the protein was realized with high frequent alternating magnetic field of 20 kA/m at 400 kHz. These results showed that under an AMF the release of GFP from magnetic composite was accelerated compared to the control sample without exposure to AMF. Furthermore a texturing of particles in the polymer matrix by a static magnetic field was investigated.

Solvent free low-melt viscosity imide oligomers and thermosetting polymide composites

NASA Technical Reports Server (NTRS)

Chuang, Chun-Hua (Inventor)

2012-01-01

.[.This invention relates to the composition and a solvent-free process for preparing novel imide oligomers and polymers specifically formulated with effective amounts of a dianhydride such as 2,3,3',4-biphenyltetra carboxylic dianydride (a-BPDA), at least one aromatic diamine and an endcapped of 4-phenylethynylphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260-280.degree. C. When the imide oligomer melt is cured at about 371.degree. C. in a press or autoclave under 100-500 psi, the melt resulted in a thermoset polyimide having a glass transition temperature (T.sub.g) equal to and above 310.degree. C. A novel feature of this process is that the monomers; namely the dianhydrides, diamines and the endcaps, are melt processable to form imide oligomers at temperatures ranging between 232-280.degree. C. (450-535.degree. F.) without any solvent. These low-melt imide oligomers can be easily processed by resin transfer molding (RTM), vacuum-assisted resin transfer molding (VARTM) or the resin infusion process with fiber preforms e.g. carbon, glass or quartz preforms to produce polyimide matrix composites with 288-343.degree. C. (550-650.degree. F.) high temperature performance capability..]. .Iadd.This invention relates to compositions and a solvent-free reaction process for preparing imide oligomers and polymers specifically derived from effective amounts of dianhydrides such as 2,3,3',4'-biphenyltetracarboxylic dianhydride (a-BPDA), at least one aromatic polyamine and an end-cap such as 4-phenylethynyphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260.degree. C.-280.degree. C..Iaddend.

An experimental study of Fe-Ni exchange between sulfide melt and olivine at upper mantle conditions: implications for mantle sulfide compositions and phase equilibria

NASA Astrophysics Data System (ADS)

Zhang, Zhou; von der Handt, Anette; Hirschmann, Marc M.

2018-03-01

The behavior of nickel in the Earth's mantle is controlled by sulfide melt-olivine reaction. Prior to this study, experiments were carried out at low pressures with narrow range of Ni/Fe in sulfide melt. As the mantle becomes more reduced with depth, experiments at comparable conditions provide an assessment of the effect of pressure at low-oxygen fugacity conditions. In this study, we constrain the Fe-Ni composition of molten sulfide in the Earth's upper mantle via sulfide melt-olivine reaction experiments at 2 GPa, 1200 and 1400 °C, with sulfide melt X_{{{Ni}}}^{{{Sulfide}}}={{Ni}}/{{Ni+{Fe}}} (atomic ratio) ranging from 0 to 0.94. To verify the approach to equilibrium and to explore the effect of {f_{{{O}2}}} on Fe-Ni exchange between phases, four different suites of experiments were conducted, varying in their experimental geometry and initial composition. Effects of Ni secondary fluorescence on olivine analyses were corrected using the PENELOPE algorithm (Baró et al., Nucl Instrum Methods Phys Res B 100:31-46, 1995), "zero time" experiments, and measurements before and after dissolution of surrounding sulfides. Oxygen fugacities in the experiments, estimated from the measured O contents of sulfide melts and from the compositions of coexisting olivines, were 3.0 ± 1.0 log units more reduced than the fayalite-magnetite-quartz (FMQ) buffer (suite 1, 2 and 3), and FMQ - 1 or more oxidized (suite 4). For the reduced (suites 1-3) experiments, Fe-Ni distribution coefficients K_{{D}}{}={(X_{{{Ni}}}^{{{sulfide}}}/X_{{{Fe}}}^{{{sulfide}}})}/{(X_{{{Ni}}^{{{olivine}}}/X_{{{Fe}}}^{{{olivine}}})}} are small, averaging 10.0 ± 5.7, with little variation as a function of total Ni content. More oxidized experiments (suite 4) give larger values of K D (21.1-25.2). Compared to previous determinations at 100 kPa, values of K D from this study are chiefly lower, in large part owing to the more reduced conditions of the experiments. The observed difference does not seem attributable to differences in temperature and pressure between experimental studies. It may be related in part to the effects of metal/sulfur ratio in sulfide melt. Application of these results to the composition of molten sulfide in peridotite indicates that compositions are intermediate in composition (X_{{{Ni}}}^{{{sulfide}}} 0.4-0.6) in the shallow mantle at 50 km, becomes more Ni rich with depth as the O content of the melt diminishes, reaching a maximum (0.6-0.7) at depths near 80-120 km, and then becomes more Fe rich in the deeper mantle where conditions are more reduced, approaching (X_{{{Ni}}}^{{{sulfide}}} 0.28) > 140 km depth. Because Ni-rich sulfide in the shallow upper mantle melts at lower temperature than more Fe-rich compositions, mantle sulfide is likely molten in much of the deep continental lithosphere, including regions of diamond formation.

The effect of melt composition on metal-silicate partitioning of siderophile elements and constraints on core formation in the angrite parent body

NASA Astrophysics Data System (ADS)

Steenstra, E. S.; Sitabi, A. B.; Lin, Y. H.; Rai, N.; Knibbe, J. S.; Berndt, J.; Matveev, S.; van Westrenen, W.

2017-09-01

We present 275 new metal-silicate partition coefficients for P, S, V, Cr, Mn, Co, Ni, Ge, Mo, and W obtained at moderate P (1.5 GPa) and high T (1683-1883 K). We investigate the effect of silicate melt composition using four end member silicate melt compositions. We identify possible silicate melt dependencies of the metal-silicate partitioning of lower valence elements Ni, Ge and V, elements that are usually assumed to remain unaffected by changes in silicate melt composition. Results for the other elements are consistent with the dependence of their metal-silicate partition coefficients on the individual major oxide components of the silicate melt composition suggested by recently reported parameterizations and theoretical considerations. Using multiple linear regression, we parameterize compiled metal-silicate partitioning results including our new data and report revised expressions that predict their metal-silicate partitioning behavior as a function of P-T-X-fO2. We apply these results to constrain the conditions that prevailed during core formation in the angrite parent body (APB). Our results suggest the siderophile element depletions in angrite meteorites are consistent with a CV bulk composition and constrain APB core formation to have occurred at mildly reducing conditions of 1.4 ± 0.5 log units below the iron-wüstite buffer (ΔIW), corresponding to a APB core mass of 18 ± 11%. The core mass range is constrained to 21 ± 8 mass% if light elements (S and/or C) are assumed to reside in the APB core. Incorporation of light elements in the APB core does not yield significantly different redox states for APB core-mantle differentiation. The inferred redox state is in excellent agreement with independent fO2 estimates recorded by pyroxene and olivine in angrites.

Molybdenum Isotopic Composition of the Archean Mantle As Inferred from Studies of Komatiites

NASA Astrophysics Data System (ADS)

Greber, N. D.; Puchtel, I. S.; Nagler, T. F.; Mezger, K.

2014-12-01

Molybdenum isotopic composition has been shown to be a powerful tool in studies of planetary processes, e.g. estimating core formation temperatures [1,2]. However, Mo isotope compositions of terrestrial reservoirs are not well constrained. In order to better constrain the Mo isotopic composition of the early Earth's mantle, komatiites from four locations were analyzed for their Mo concentrations and isotopic compositions. Komatiites are particularly appropriate for this type of study because they formed by high degrees of partial melting of the mantle leading to a complete base metal sulfide removal from the residual mantle and the production of sulfur-undersaturated melts and thus a quantitative removal of Mo from the source into the melt. All samples, except for two strongly altered specimens specifically chosen to study the effects of secondary alteration, are very fresh having preserved most of their primary mineralogy. The Mo concentrations in komatiites range from 10 to 120 ng/g. Fresh komatiites have lighter δ98Mo (NIST SRM 3134 = 0.25‰, [3]) than altered samples. The estimated primary Mo isotope compositions of the studied komatiite melts range from 0.02 ± 0.16‰ to 0.19 ± 0.14‰ and are therefore indistinguishable within analytical uncertainty (2SD) from published values for chondritic meteorites (0.09 ± 0.04 ‰; 2SD; [2]) and lighter than the proposed average for Earth's continental crust (0.3 to 0.4‰ [4]). All data combined, although overlapping in errors, show a consistent trend of lighter δ98Mo and lower Mo concentrations in more melt-depleted mantle sources, indicating incompatible behaviour of Mo and preferential mobilization of heavy Mo isotopes during mantle melting. [1] Hin et al. (2013) EPSL, 379 [2] Burkhardt et al. (2014) EPSL, 391 [3] Nägler, et al. (2014) GGR, 38. [4] Voegelin et al. (2014) Lithos, 190-191.

Electrical Conductivity Measurements on Hydrous Carbonate Melts at Mantle Pressure

NASA Astrophysics Data System (ADS)

Sifre, D.; Gaillard, F.

2012-04-01

Electromagnetic methods image mantle regions in the asthenosphere with elevated conductivity (0.1 to 1 S.m-1), which constrasts with the conductivity of dry olivine (10-2 to 10-3 S.m-1). A correct interpretation of the petrological nature of the conductive mantle is critical for our understanding of mantle geodynamics because such conductive regions indicate mantle rocks with physical and chemical properties that importantly deviates from the canonical peridotites. For decades, such anomalously high mantle conductivities have been attributed to mineralogical defects associated to few tens of ppm water incorporated in olivine. Most recent experimental surveys, however, refute this hydrous olivine model. Conductive mantle regions could then reflect partial melting. The presence of melts in the Earth's mantle has long been proved by geochemical observations and experimental petrology on peridotite rocks. The requirement for melting in the asthenospheric mantle is the presence of volatile species (water, carbon dioxide, halogens). Small melt fractions are then produced by small volatile contents and they are the first liquids produced by melting magma. This study reports electrical conductivity measurements on such melts at mantle pressure and temperature. We investigated on melt chemical compositions produced by melting of peridotite that would interact with CO2-H2O and Cl. Such melts are carbonatite melts, carbonated silicate melts, hydrous carbonate melts, hydrous basalts. A new system allowing in situ electrical conductivity measurements in piston cylinder has been deployed. This design has been specifically adapted to perfom measurements on liquid samples with elevated electrical conductivities. The chemical compositions investigated are pure liquid CaCO3 and CaMg(CO3)2, to which, cloride (as salts), silicate (as basalts) and water (as brucite) have been added. Experiments have been realized at 1.5 and 2.7 GPa pressure and temperature of 1000-1700° C. Impedance spectrometry measurements are realized using a Solartron gainphase analyser. In the liquid state, which was identified at T varying from 1000-1700° C depending on chemical compositions, all investigated samples are extremely conductive, i.e. >100 S.m-1. It is 10,000 times more conductive than mantle olivine at similar P and T. The conductivities of samples increase with temperature and Arrhenius relationships can be adjusted. Activation energies depend on chemical compositions and vary from 40 to 80 kJ.mol-1. Conductivity of melts increases in the following sequence: CaCO3 < MgCa(CO3)2 < (MgCa(CO3)2)0.9 (NaCl)0.1 < (CaCO3)0.45 (NaCl)0.1 (MgH2O2)0.45. The latter melt composition is a simplified synthetic analogue of fluid inclusions entrapped in diamonds. Its electrical conductivity increases to >200 S.m-1 at 1410° C and 2.7 GPa. An electromagnetic survey (Tarits et al, this session) identifies a conductive mantle underneath mid-ocean ridge from 100 to nearly 500 km of depth. The determined conductivity, 0.1 S.m-1, is obtained considering 0.07 volume % of hydrous carbonated melts in peridotite rocks. This is equivalent to a peridotite with 175 ppm CO2 and 67 ppm water stored as small melt fraction wetting grain boundaries. Geochemical and geodynamic implications are discussed by Gaillard (this session).

Core Formation: an Experimental Study of Metallic Melt-Silicate Segregation

NASA Astrophysics Data System (ADS)

Herpfer, M. A.; Larimer, J. W.

1993-07-01

To a large extent, the question of how metallic cores form reduces to the problem of understanding the surface tension between metallic melts and silicates [1]. This problem was addressed by performing experiments to determine the surface tensions between metallic melts with variable S contents and the silicate phases (olivine and orthopyroxene) expected in planetary mantles. The experiments were conducted in a piston-cylinder apparatus at P = 1GPa and T = 1250-1450 degrees C. Textural and chemical equilibration was confirmed in several ways: theoretical estimates were checked by conducting a series of experiments at progressively longer times (up to 72 hrs) until phase composition and dihedral angle ceased to change and the distribution of measured "apparent" angles matched the standard cumulative frequency curve. The dihedral "wetting" angles (theta) were measured from high resolution photomicrgraphs using a 10X optical protractor; 100-400 measurements were made for most experiments. The dihedral angle is related to the ratio of interfacial energies: gamma(sub)ss/gamma(sub)sl = 2 cos(theta/2), where gamma(sub)ss and gamma(sub)sl are the interfacial energies between solid-solid and liquid-solid. Since data exist for the pertinent solid-solid energies, the liquid-solid interfacial energies can be computed from measured theta values. However, the important relations are best expressed in terms of theta values. The extent to which a melt is interconnected along grain boundaries, and hence able to flow and segregate depends on the value of theta and the fraction of melt present. When theta < 60 degrees, the liquid can be interconnected at all melt fractions but when theta > 60 degrees, the melt fraction must be at least 1 vol% and increses as theta increases. Actually there is a predicted effect, analogous to a hysteresis effect, where for a given theta value the amount of melt that needs to be added for interconnection is greater than the amount left when the melt disconnects (pinches off). In our experiments, where dense metallic melt drained away, the disconnect theta values match the theoretical predictions. The composition of the metallic melt in the experiments was varied from stoichiometric FeS to Fe/S ratios near the the eutectic and on to more Fe rich compositons. The theta values vary in a systematic manner; for example, for melts in contact with olivine at 1300 degrees C the theta values range from 67 degrees for FeS to 55 degrees at the eutectic and back toward higher values at higher Fe contents. Theoretical considerations indicate that eutectic compositions are expected to have the lowest theta values, just as observed. The theta values indicate that melts with eutectic composition can interconnect and segregate at 1-2 vol% melt fraction at 1300 degrees C. Some previous estimates of the melt fraction required for interconnection are much higher [2,3], but the inferences were drawn from experiments that were not designed to test for textural equilibrium, fraction of melt present, etc. The present experiments clearly show that metallic melts can readily segregate from solid silicates. Simple extrapolations to other phases, compositions and PT conditions provide a rather complete picture of how the "plumbing" worked in the mantles of planetary objects during the initial stages of core segregation. References: [1] Stevenson D. J. (1990) In Origin of the Earth, 231-249. [2] Taylor G. J. (1989) LPSC XX, 1109. [3] Walker D. and Agee C. B. Meteor. 23, 81-91.

The Apollo 17 'melt sheet' - Chemistry, age and Rb/Sr systematics

NASA Technical Reports Server (NTRS)

Winzer, S. R.; Nava, D. F.; Schuhmann, S.; Philpotts, J. A.; Schuhmann, P. J.; Lum, R. K. L.; Lindstrom, M. M.; Lindstrom, D. J.

1977-01-01

Major, minor, and trace-element compositions, age data, and Rb/Sr systematics of Apollo 17 boulders have been compiled, and additional analyses performed on a norite breccia clast (77215) included in the Apollo 17, Station 7 boulder. The Apollo 17 boulders are found to be identical or nearly so in major, minor, and trace-element composition, suggesting that they all originated as an impact melt analogous to melt sheets found in larger terrestrial craters. The matrix dates (Ar-40/Ar-39) and Rb/Sr systematics available suggest that this impact melt formed by a single impact about 4 billion years ago. This impact excavated, shocked, brecciated, and melted norites, norite cumulates, and possibly anorthositic gabbros and dunites about 4.4 billion years old. The impact was likely a major one, possibly the Serenitatis basin-forming event.

A Modeling Approach to Fiber Fracture in Melt Impregnation

NASA Astrophysics Data System (ADS)

Ren, Feng; Zhang, Cong; Yu, Yang; Xin, Chunling; Tang, Ke; He, Yadong

2017-02-01

The effect of process variables such as roving pulling speed, melt temperature and number of pins on the fiber fracture during the processing of thermoplastic based composites was investigated in this study. The melt impregnation was used in this process of continuous glass fiber reinforced thermoplastic composites. Previous investigators have suggested a variety of models for melt impregnation, while comparatively little effort has been spent on modeling the fiber fracture caused by the viscous resin. Herein, a mathematical model was developed for impregnation process to predict the fiber fracture rate and describe the experimental results with the Weibull intensity distribution function. The optimal parameters of this process were obtained by orthogonal experiment. The results suggest that the fiber fracture is caused by viscous shear stress on fiber bundle in melt impregnation mold when pulling the fiber bundle.

Brittle deformation in Southern Granulite Terrane (SGT): A study of pseudotachylyte bearing fractures along Gangavalli Shear Zone (GSZ), Tamil Nadu, India.

NASA Astrophysics Data System (ADS)

mohan Behera, Bhuban; Thirukumaran, Venugopal; Biswal, Tapas kumar

2016-04-01

High grade metamorphism and intense deformation have given a well recognition to the Southern Granulite Terrane (SGT) in India. TTG-Charnockite and basic granulites constitute the dominant lithoassociation of the area. Dunite-peridotite-anorthosite-shonkinite and syenites are the intrusives. TTG-charnockite-basic granulite have undergone F1 (isoclinal recumbent), F2 (NE-SW) and F3 (NW-SE) folds producing several interference pattern. E-W trending Neoarchean and Palaeoproterozoic Salem-Attur Shear Zone exhibits a low angle ductile thrust as well as some foot print of late stage brittle deformation near Gangavalli area of Tamil Nadu. The thrust causes exhumation of basic granulites to upper crust. Thrusting along the decollement has retrograded the granulite into amphibolite rock. Subsequently, deformation pattern of Gangavalli area has distinctly marked by numerous vertical to sub-vertical fractures mostly dominating along 0-15 and 270-300 degree within charnockite hills that creates a maximum stress (σ1) along NNW and minimum stress (σ3) along ENE. However, emplacement of pseudotachylyte vein along N-S dominating fracture indicates a post deformational seismic event. Extensive fractures produce anastomose vein with varying thickness from few millimeters to 10 centimeters on the outcrop. ICP-AES study results an isochemical composition of pseudotachylyte vein that derived from the host charnockitic rock where it occurs. But still some noticeable variation in FeO-MgO and Na2O-CaO are obtained from different parts within the single vein showing heterogeneity melt. Electron probe micro analysis of thin sections reveals the existence of melt immiscibility during its solidification. Under dry melting condition, albitic rich melts are considered to be the most favorable composition for microlites (e.g. sheaf and acicular micro crystal) re-crystallization. Especially, acicular microlites preserved tachylite texture that suggest its formation before the final coagulation. Profuse sub-rounded clasts embedded in the melt are identified as hexagonal β-quartz (through XRD technique) that has undergone decrepitation along grain boundary. Thus partial melting of quartz can be suggested an ultrahigh temperature of 1550 degree Celsius has reached during formation of Gangavalli pseudotachylyte. Magmatic zircon grains from the pseudotachylyte veins are providing two age groups; the oldest ages are 2550±16 and 2508±14 Ma while the younger ages are 1848±24 and 1875±22 Ma. Here, we interpret that these zircons have no relation with the formation of pseudotachylyte because of its fast solidification. Hence, protolith belongs to 1848±24 and 1875±22 Ma age with xenocrysts of 2550±16 and 2508±14 Ma.

Amphibole-bearing multiphase solid inclusions in olivine, the Murotomisaki Gabbro, Southwest Japan: An evidence of hydrous flux melting

NASA Astrophysics Data System (ADS)

Hoshide, T.; Obata, M.

2009-12-01

The Murotomisaki Gabbro is a sill-like layered intrusion of up to 220m thickness exposed near Cape Muroto, Southwest Japan. Despite the small size of the intrusion, it contains well-developed centimeter- to meter-scale layered structures of modal variation of olivine, plagioclase and augite. Hoshide et al (2006a, b) identified the ’crystal accumulation zone’ (40m from the bottom) that was formed by gravitational settling of olivine crystals and the ’crystal growth zone’ (40-100m from the bottom), in which olivine crystals grew significantly. The fine-scale compositional layering is best developed in the ’crystal growth zone’. Amphibole-bearing multiphase solid inclusions (called ‘the amphibole-clot inclusions’) are common in olivine crystals from both the crystal accumulation- and the crystal growth zones. The amphibole clot inclusions show spherical or convex-polygonal shapes and are composed of pargasitic amphibole, biotite and orthopyroxene, with minor amounts of augite, apatite and opaque minerals. Plagioclase rarely occurs in the amphibole clot inclusions. Bulk chemical compositions of the inclusions, obtained from mineral microprobe analyses and modal composition, are characteristically high in MgO content (16-23 wt %) and they roughly lie between presumable fractionated melt compositions and olivine compositions. From observations above, it is likely that amphibole clot inclusions are of melt origin, which had formed from some hydrous melts probably entrapped in growing olivine crystals. However, it may be difficult to explain both the very magnesian nature of the inclusion and absence of plagioclase in the inclusion by the crystallization of the normal hydrous basaltic melt. The difficulty may be resolved if we suppose, for a trapped melt composition, a more magnesian (i.e., picritic) composition. The highly magnesian nature of the amphibole clot inclusions may suggest that significant amount of olivine component had been added to fractionated melts that was once equilibrated with olivine. Such addition of olivine component may be realized by dissolution of olivine, which may be induced by introduction of water from the lower horizons of the crystallization boundary layer (e.g., McBirney, 1987). Amphibole clot inclusion in olivine is, therefore, considered to be a new evidence for dissolution of olivine by hydrous fluxing.

Complications in Determining Oxygen Fugacities From Olivine-Melt Equilibrium Illustrated by the Pu'u'O'o Lavas, Hawaii

NASA Astrophysics Data System (ADS)

McCann, V. E.; Barton, M.; Thornber, C. R.

2005-12-01

We have shown previously that oxygen fugacities calculated from olivine-melt equilibrium using rim compositions agree well with those calculated from analyzed Fe3+/σFe for MORB and for Icelandic OIB (MORB - average ΔFMQ -0.72 versus -0.70, Iceland average ΔFMQ -0.49 versus -0.58). The agreement between oxygen fugacities calculated from Ol-melt equilibrium and those calculated from analyzed Fe3+/σFe is excellent for individual samples of MORB from the FAMOUS region and Blanco Trough ( difference in calculated ΔFMQ < 0.30). Published analyses of Fe3+/σFe yield oxygen fugacilties of ΔFMQ= -0.72±0.43 for lavas from Kilauea and Mauna Loa, and ΔFMQ=0.91±0.72 for Loihi, very close to those for MORB. Oxygen fugacities determined using carefully selected Ol-melt analyses (ΔFMQ= -0.43±0.32) are in reasonable agreement with those determined from Fe3+/σFe for Kilauea and Mauna Loa, and agreement between fO2 calculated from Ol-melt equilibrium (ΔFMQ= -0.26) and that calculated from Fe3+/σFe (ΔFMQ= -0.64) is excellent for one sample from Kilauea. However, olivine-melt pairs from some samples, including those from the Pu'u'O'o lavas, yield anomalously high or low estimates of fO2 (average ΔFMQ =-0.6907, range -4.07 to +0.34). We suggest that these anomalous values reflect the complex history of olivines in these lavas, in particular the effects of magma mixing. Some olivines in the Pu'u'O'o lavas clearly have rims that are anomalously rich in Fa, whereas others have rims that are anomalously rich in Fo and do not appear to have equilibrium compositions. Given the dependence of olivine composition on melt Fe3+/σFe, there is no simple method to determine the equilibrium composition of olivine for a particular melt. However, detailed zoning profiles and analyses of microphenocrysts allow probable equilibrium compositions to be identified. We suggest that the average fO2 of Hawaiian lavas lies close to (ΔFMQ= -1) based on published results using spinel-melt equilibrium and Fe-Ni exchange between olivine and sulfide liquid. Olivine-glass inclusion data for Koolau samples also suggest (ΔFMQ= ~-1).

Volcanic Infillings of Large Basins on Mercury as Indicators of Mantle Thermal State and Composition

NASA Astrophysics Data System (ADS)

Padovan, Sebastiano; Tosi, Nicola; Plesa, Ana-Catalina; Ruedas, Thomas

2017-04-01

The crust of Mercury is mostly the cumulative result of partial melting in the mantle associated with solid-state convection [1]. The details of how the surface composition represents the result of dynamical processes in the interior are difficult to elucidate. Explanations for the observed geochemically varied surface include a heterogeneous mantle, the effects of ancient giant impacts, an evolving mantle composition, or a combination of these processes [e.g., 2]. Here we explore the effects of large impacts on mantle dynamics and associated melt production. With the convection code GAIA we compute thermal evolution histories of Mercury compatible with the expected amount of heat producing elements in the mantle and with the crustal thickness inferred from gravity and topography data. We estimate the thermal anomalies in the mantle generated by large impacts using scaling laws [3]. Impactors have a velocity of 42 km/s and an impact angle of 45°, as appropriate for Mercury [4]. Their size is varied in order to produce basins with diameters in the range from 715 km (Rembrandt) to 1550 km (Caloris). Depending on the timing of the impact, the melt erupting in the basin interior is a combination of convective melt generated at depth and shallow melt resulting from shallow impact-induced convective currents. The volcanic infillings following an impact happening early in the evolution of the planet, when convection is still vigorous, are dominated by convective melt. Later in the evolution, the erupted melt shows the signature of the impact-induced shallow melt. We show that the properties of melt sheets within the young large basins Caloris and Rembrandt depend on the mantle thermal state and composition. In particular, we predict the source depth of the volcanic plains within large young basins to be different from the source depth of older surface units, a result that can help explaining the peculiar composition of the volcanic plains inside Caloris [2, 5]. [1] Tosi N. et al. (2013), JGR-Planets, 118, 2474—2487. [2] Weider S.Z. et al. (2015) EPSL, 416, 109—120. [3] Roberts J.H. and Barnouin O.S. (2012), JGR-Planets, 117, E02007. [4] Le Feuvre M. and Wieczorek M.A. (2008), Icarus, 197, 291—306. [5] Namur O. and Charlier B. (2017), Nature Geosc., 10, 9—13.

Melt extraction and mantle source at a Southwest Indian Ridge Dragon Bone amagmatic segment on the Marion Rise

NASA Astrophysics Data System (ADS)

Gao, Changgui; Dick, Henry J. B.; Liu, Yang; Zhou, Huaiyang

2016-03-01

This paper works on the trace and major element compositions of spatially associated basalts and peridotites from the Dragon Bone amagmatic ridge segment at the eastern flank of the Marion Platform on the ultraslow spreading Southwest Indian Ridge. The rare earth element compositions of basalts do not match the pre-alteration Dragon Bone peridotite compositions, but can be modeled by about 5 to 10% non-modal batch equilibrium melting from a DMM source. The Dragon Bone peridotites are clinopyroxene-poor harzburgite with average spinel Cr# 27.7. The spinel Cr# indicates a moderate degree of melting. However, CaO and Al2O3 of the peridotites are lower than other abyssal peridotites at the same Mg# and extent of melting. This requires a pyroxene-poor initial mantle source composition compared to either hypothetical primitive upper mantle or depleted MORB mantle sources. We suggest a hydrous melting of the initial Dragon Bone mantle source, as wet melting depletes pyroxene faster than dry. According to the rare earth element patterns, the Dragon Bone peridotites are divided into two groups. Heavy REE in Group 1 are extremely fractionated from middle REE, which can be modeled by 7% fractional melting in the garnet stability field and another 12.5 to 13.5% in the spinel stability field from depleted and primitive upper mantle sources, respectively. Heavy REE in Group 2 are slightly fractionated from middle REE, which can be modeled by 15 to 20% fractional melting in the spinel stability field from a depleted mantle source. Both groups show similar melting degree to other abyssal peridotites. If all the melt extraction occurred at the middle oceanic ridge where the peridotites were dredged, a normal 6 km thick oceanic crust is expected at the Dragon Bone segment. However, the Dragon Bone peridotites are exposed in an amagmatic ridge segment where only scattered pillow basalts lie on a partially serpentinized mantle pavement. Thus their depletion requires an earlier melting occurred at other place. Considering the hydrous melting of the initial Dragon Bone mantle source, we suggest the earlier melting event occurred in an arc terrain, prior to or during the closure of the Mozambique Ocean in the Neproterozoic, and the subsequent assembly of Gondwana. Then, the Al2O3 depleted and thus buoyant peridotites became the MORB source for Southwest Indian Ridge and formed the Marion Rise during the Gondwana breakup.

The variable influence of P 2O 5 on the viscosity of melts of differing alkali/aluminium ratio: Implications for the structural role of phosphorus in silicate melts

NASA Astrophysics Data System (ADS)

Toplis, M. J.; Dingwell, D. B.

1996-11-01

The shear viscosities of forty melts in the system Na 2OAl 2O 3SiO 2P 2O 5 have been determined in the temperature range 1652-1052°C using the concentric cylinder method. Six P-free compositions containing ˜67 mol% SiO 2 varying in molar Na/(Na + Al) from 0.70 (peralkaline) to 0.44 (peraluminous) were studied, to each of which successive additions of up to 7 mol% (13 wt%) P 2O 5 were made. At a fixed temperature, viscosities in the P-free system show a maximum, not at the 'charge-balanced' metaluminous composition ( Na/(Na + Al) = 0.50 ), but at Na/(Na + Al) = 0.47 . Addition of P to peralkaline melts results in an increase in viscosity. With progressive additions of P to mildly peralkaline melts ( Na/(Na + Al) < 0.60 ), there is a maximum in melt viscosity that occurs at lower P content as the peralkalinity of the melt decreases. In contrast, the addition of P to the metaluminous and peraluminous melts causes a decrease in melt viscosity. The magnitude of this decrease is identical for the metaluminous, and mildly peraluminous ( Na/(Na + Al) = 0.47 ) compositions, but smaller for the most peraluminous melt ( Na/(Na + Al) = 0.44 ). The following inferences are made from the present viscosity data, together with spectroscopic data from the literature: (1) At the metaluminous join in the P-free system, not all the Al is present as a charge-balanced network-former. Between the metaluminous join and the viscosity maximum the incorporation of a small proportion of Al (3% relative) in a charge-balancing role (for Al IV) could explain the observations. (2) The addition of P to peralkaline melts results in the formation of Na phosphate complexes which, upon exhaustion of excess Na, have the stoichiometry of extended metaphosphate chains with Na/P ratios that tend to 1 as the metaluminous ioin is approached. (3) Estimates of the relative effects of Na and Al phosphate melt complexes on viscosity are consistent with the formation of both NaPO 3 and AlPO 4 melt complexes upon addition of P to metaluminous melts. (4) In the most peraluminous melts studied, P is inferred to interact with both excess Al and network-forming aluminates, suggesting that these two species have similar energetic stabilities. Given that many granites lie close to the metaluminous join in composition, the results of this study have implications for the physical and chemical evolution of such natural systems.

Effects of water, depth and temperature on partial melting of mantle-wedge fluxed by hydrous sediment-melt in subduction zones

NASA Astrophysics Data System (ADS)

Mallik, Ananya; Dasgupta, Rajdeep; Tsuno, Kyusei; Nelson, Jared

2016-12-01

This study investigates the partial melting of variable bulk H2O-bearing parcels of mantle-wedge hybridized by partial melt derived from subducted metapelites, at pressure-temperature (P-T) conditions applicable to the hotter core of the mantle beneath volcanic arcs. Experiments are performed on mixtures of 25% sediment-melt and 75% fertile peridotite, from 1200 to 1300 °C, at 2 and 3 GPa, with bulk H2O concentrations of 4 and 6 wt.%. Combining the results from these experiments with previous experiments containing 2 wt.% bulk H2O (Mallik et al., 2015), it is observed that all melt compositions, except those produced in the lowest bulk H2O experiments at 3 GPa, are saturated with olivine and orthopyroxene. Also, higher bulk H2O concentration increases melt fraction at the same P-T condition, and causes exhaustion of garnet, phlogopite and clinopyroxene at lower temperatures, for a given pressure. The activity coefficient of silica (ϒSiO2) for olivine-orthopyroxene saturated melt compositions (where the activity of silica, aSiO2 , is buffered by the reaction olivine + SiO2 = orthopyroxene) from this study and from mantle melting studies in the literature are calculated. In melt compositions generated at 2 GPa or shallower, with increasing H2O concentration, ϒSiO2 increases from <1 to ∼1, indicating a transition from non-ideal mixing as OH- in the melt (ϒSiO2 <1) to ideal mixing as molecular H2O (ϒSiO2 ∼1). At pressures >2 GPa, ϒSiO2 >1 at higher H2O concentrations in the melt, indicate requirement of excess energy to incorporate molecular H2O in the silicate melt structure, along with a preference for bridging species and polyhedral edge decorations. With vapor saturation in the presence of melt, ϒSiO2 decreases indicating approach towards ideal mixing of H2O in silicate melt. For similar H2O concentrations in the melt, ϒSiO2 for olivine-orthopyroxene saturated melts at 3 GPa is higher than melts at 2 GPa or shallower. This results in melts generated at 3 GPa being more silica-poor than melts at 2 GPa. Thus, variable bulk H2O and pressure of melt generation results in the partial melts from this study varying in composition from phonotephrite to basaltic andesite at 2 GPa and foidite/phonotephrite to basalt at 3 GPa, forming a spectrum of arc magmas. Modeling suggests that the trace element patterns of sediment-melt are unaffected by the process of hybridization within the hotter core of the mantle-wedge. K2O/H2O and H2O/Ce ratios of the sediment-melts are unaffected, within error, by the process of hybridization of the mantle-wedge. This implies that thermometers based on K2O/H2O and H2O/Ce ratios of arc lavas may be used to estimate slab-top temperatures when (a) sediment-melt from the slab reaches the hotter core of the mantle-wedge by focused flow (b) sediment-melt freezes in the overlying mantle at the slab-mantle interface and the hybridized package rises as a mélange diapir and partially melts at the hotter core of the mantle-wedge. Based on the results from this study and previous studies, both channelized and porous flow of sediment-melt/fluid through the sub-arc mantle can explain geochemical signatures of arc lavas under specific geodynamic scenarios of fluid/melt fluxing, hybridization, and subsequent mantle melting.

Effect of Low-Melting Metals (Pb, Bi, Cd, In) on the Structure, Phase Composition, and Properties of Casting Al-5% Si-4% Cu Alloy

NASA Astrophysics Data System (ADS)

Yakovleva, A. O.; Belov, N. A.; Bazlova, T. A.; Shkalei, I. V.

2018-01-01

The effect of low-melting metals (Pb, Bi, Cd, In) on the structure, phase composition, and properties of the Al-5% Si-4% Cu alloy was studied using calculations. Polythermal sections have been reported, which show that the considered systems are characterized by the presence of liquid regions and monotectic reactions. The effect of low-melting metals on the microstructure and hardening of base alloy in the cast and heat-treated states has been studied.

Kinetics of the melting front movement in process of centrifugal induction surfacing of powder material with nanoscale modificaters

NASA Astrophysics Data System (ADS)

Sasnouski, I.; Kurylionak, A.

2018-03-01

For solving the problem of improving the powder coatings modified by nanostructure components obtained by induction surfacing method tribological characteristics it is necessary to study the kinetics of the powdered layer melting and define the minimum time of melting. For powdered layer predetermined temperature maintenance at sintering mode stage it is required to determine the temperature difference through blank thickness of the for one hundred-day of the define the warm-up swing on of the stocking up by solving the thermal conductivity stationary problem for quill (hollow) cylinder with internal heat source. Herewith, since in practice thickness of the cylinder wall is much less then its diameter and the temperature difference is comparatively small, the thermal conductivity dependence upon the temperature can be treated as negligible. As it was shown by our previous studies, in the induction heating process under powdered material centrifugal surfacing (i.e. before achieving the melting temperature) the temperature distribution in powdered layer thickness may be considered even. Hereinafter, considering the blank part induction heating process quasi-stationarity under Fo big values, it is possible to consider its internal surface heating as developing with constant velocity. As a result of development the melting front movement mathematical model in a powdered material with nanostructure modifiers the minimum surfacing time is defined. It allows to minimize negative impact of thermal influence on formation of applied coating structure, to raise productivity of the process, to lower power inputs and to ensure saving of nonferrous and high alloys by reducing the allowance for machining. The difference of developed mathematical model of melting front movement from previously known is that the surface temperature from which the heat transfer occures is a variable and varies with a time after the linear law.

Magma degassing: novel experiments with multiple volatile species on H2O, CO2, S and Cl and development of a new thermodynamic model

NASA Astrophysics Data System (ADS)

Lesne, P.; Witham, F.; Kohn, S.; Blundy, J.; Botcharnikov, R. E.; Behrens, H.

2010-12-01

Geochemical measurements, from chemistry of melt inclusion to gas fluxes and compositions, give important clues to help understand magma and gas transport from a magma chamber towards the surface. These data are of the utmost importance to constrain models of the mass transport processes occurring in volcanic systems. Experimental work is central to testing such models. The behaviour of water and carbon dioxide fluids in basaltic melts have been well studied in previous works (i.e. Dixon et al., 1995; Newman & Lowenstern, 2002; Papale et al., 2006). The various models agree that the gases exsolved at high pressures are rich in CO_{2}, and at lower pressures, when most of the CO_{2} has already moved to the fluid phase, H_{2}O strongly partitions into the fluid and the melt become dehydrated (e.g. Newman & Lowenstern, 2002; Papale et al, 2006). S and Cl are much less abundant in the atmosphere than H_{2}O and CO_{2} and therefore give much higher signal ratio to noise ratios than volcanogenic H_{2}O and CO_{2}. H_{2}O, CO_{2}, S and Cl being the major volatiles measured at vent in melt inclusions in volcanic systems, a detailed model of S and Cl behaviour in basaltic melts is highly valuable in order to better understand volcanic gas emissions, and to test models of degassing processes. We have developed a model for mixed C-O-H-S-Cl fluids in equilibrium with basalt. The model is based on the premise that the volumetrically dominant volatile components, H_{2}O and CO_{2}, will determine the behaviour of S and Cl. Equilibrium experiments between a C-O-H-S-Cl fluid and basaltic melts from Stromboli and Masaya have been performed, at 1150°C, under oxidized conditions and at pressure from 25 to 400MPa. Analyses of volatiles dissolved in the melt and determined fluid composition allow us to determine equilibrium constants and partition coefficients of S and Cl between a CO_{2}-H_{2}O-rich fluid phase and basaltic melt. Equilibrium constants were parameterized using a S-rich basaltic composition (Stromboli), and have been tested against independent S-poor basaltic composition melts for Stromboli, and two volatile compositions from Masaya volcano. Our model reproduces all these experimental data with good agreement. The geochemical model will be published as a user-friendly software package, SolEx, to allow easy prediction of melt and fluid phase chemistries. We hope that this will facilitate comparisons between fluid-mechanical models of volcanic behaviour and measurements of melt inclusion chemistry and emitted gas compositions and fluxes. Dixon et al., 1995, J. Pet., 36, 1607-1631; Newman & Lowenstern, 2002, Computers & Geosciences, 28, 597-604; Papale et al., 2006, Chem. Geol., 229, 78-95.

Os-Hf-Sr-Nd isotope and PGE systematics of spinel peridotite xenoliths from Tok, SE Siberian craton: Effects of pervasive metasomatism in shallow refractory mantle

NASA Astrophysics Data System (ADS)

Ionov, Dmitri A.; Shirey, Steven B.; Weis, Dominique; Brügmann, Gerhard

2006-01-01

Os-Hf-Sr-Nd isotopes and PGE were determined in peridotite xenoliths carried to the surface by Quaternary alkali basaltic magmas in the Tokinsky Stanovik Range on the Aldan shield. These data constrain the timing and nature of partial melting and metasomatism in the lithospheric mantle beneath SE Siberian craton. The xenoliths range from the rare fertile spinel lherzolites to the more abundant, strongly metasomatised olivine-rich (70-84%) rocks. Hf-Sr-Nd isotope compositions of the xenoliths are mainly within the fields of oceanic basalts. Most metasomatised xenoliths have lower 143Nd / 144Nd and 176Hf / 177Hf and higher 87Sr / 86Sr than the host basalts indicating that the metasomatism is older and has distinct sources. A few xenoliths have elevated 176Hf / 177Hf (up to 0.2838) and plot above the Hf-Nd mantle array defined by oceanic basalts. 187Os / 188Os in the poorly metasomatised, fertile to moderately refractory (Al2O3 ≥ 1.6%) Tok peridotites range from 0.1156 to 0.1282, with oldest rhenium depletion ages being about 2 Ga. The 187Os / 188Os in these rocks show good correlations with partial melting indices (e.g. Al2O3, modal cpx); the intercept of the Al-187Os / 188Os correlation with lowest Al2O3 estimates for melting residues (∼0.3-0.5%) has a 187Os / 188Os of ∼0.109 suggesting that these peridotites may have experienced melt extraction as early as 2.8 Gy ago. 187Os / 188Os in the strongly metasomatised, olivine-rich xenoliths (0.6-1.3% Al2O3) ranges from 0.1164 to 0.1275 and shows no apparent links to modal or chemical compositions. Convex-upward REE patterns and high abundances of heavy to middle REE in these refractory rocks indicate equilibration with evolved silicate melts at high melt / rock ratios, which may have also variably elevated their 187Os / 188Os. This inference is supported by enrichments in Pd and Pt on chondrite-normalised PGE abundance patterns in some of the rocks. The melt extraction ages for the Tok suite of 2.0 to 2.8 Ga are younger than oldest Os ages reported for central Siberian craton, but they must be considered minimum estimates because of the extensive metasomatism of the most refractory Tok peridotites. This metasomatism could have occurred in the late Mesozoic to early Cenozoic when the Tok region was close to the subduction-related Pacific margin of Siberia and experienced large-scale tectonic and magmatic activity. This study indicates that metasomatic effects on the Re-Os system in the shallow lithospheric mantle can be dramatic.

Thermal and petrologic constraints on the lower crustal melt accumulation in the Salton Sea Geothermal Field

NASA Astrophysics Data System (ADS)

Karakas, O.; Dufek, J.; Mangan, M.; Wright, H. M. N.

2014-12-01

Heat transfer in active volcanic areas is governed by complex coupling between tectonic and magmatic processes. These two processes provide unique imprints on the petrologic and thermal evolution of magma by controlling the geometry, depth, longevity, composition, and fraction of melt in the crust. The active volcanism, tectonic extension, and significantly high surface heat flow in Salton Sea Geothermal Field, CA, provides information about the dynamic heat transfer processes in its crust. The volcanism in the area is associated with tectonic extension over the last 500 ka, followed by subsidence and sedimentation at the surface level and dike emplacement in the lower crust. Although significant progress has been made describing the tectonic evolution and petrology of the erupted products of the Salton Buttes, their coupled control on the crustal heat transfer and feedback on the melt evolution remain unclear. To address these concepts, we develop a two-dimensional finite volume model and investigate the compositional and thermal evolution of the melt and crust in the Salton Sea Geothermal Field through a one-way coupled thermal model that accounts for tectonic extension, lower crustal magma emplacement, sedimentation, and subsidence. Through our simulations, we give quantitative estimates to the thermal and compositional evolution and longevity of the lower crustal melt source in the crustal section. We further compare the model results with petrologic constraints. Our thermal balance equations show that crustal melting is limited and the melt is dominated by mantle-derived material. Similarly, petrologic work on δ18O isotope ratios suggests fractional crystallization of basalt with minor crustal assimilation. In addition, we suggest scenarios for the melt fraction, composition, enthalpy release, geometry and depth of magma reservoirs, their temporal evolution, and the timescales of magmatic storage and evolution processes. These parameters provide the source conditions for the dynamics of surface volcanism and the presence of a geothermal system, which modify the thermal and mechanical structure of the crust.

Diffusion of major and trace elements in natural silicate melts as a tool to investigate timescales in magma mixing

NASA Astrophysics Data System (ADS)

González-García, Diego; Zezza, Angela; Behrens, Harald; Vetere, Francesco; Petrelli, Maurizio; Morgavi, Daniele; Perugini, Diego

2016-04-01

New melt injection into a shallow magma chamber is regarded as one of the potential triggers for explosive volcanic eruptions. Chemical diffusion occurring between the two mixing melts is a time-dependent process, and thus has the potential to shed light on the timescales involved in magma mixing events leading to an eruption. In order to achieve this, a complete database of diffusion coefficients in natural melts is a necessary prerequisite. We have carried out a set of 12 diffusion couple experiments in order to determine diffusion coefficients (D) of major and trace elements in two natural silicate melts. Two end-members from the Vulcano island (Aeolian archipelago, Italy) have been chosen for the experiments: a shoshonite (Vulcanello lava platform) and a rhyolitic obsidian (Pietre Cotte lava flow, La Fossa cone). Glasses from each end-member with added water contents of 0 wt%, 1 wt% and 2 wt% were produced in an Internally Heated Pressure Vessel (IHPV). Two glass cylinders with similar water content but different base composition are inserted in Au-Pd capsules and experiments are run in the IHPV at 1200° C with pressure from 0.5 to 3 kbar. Experiment capsules are rapidly quenched and analyzed by FTIR, EPMA and LA-ICP-MS for H2O, major and trace elements, respectively, along 2 mm linear profiles extending across the interface. A Boltzmann-Matano approach is used to obtain concentration-dependent diffusivities. The obtained concentration-distance profiles are asymmetric and extend deeper into the shoshonite relative to the rhyolite, indicating that diffusion is slower in the latter. Results show that diffusivities are notably accelerated by the presence of H2O in the melt. Experiments performed by using water-free glass show diffusivities one order of magnitude lower compared to glasses containing up to 2 wt% H2O. The effect of pressure, in the investigated range, is negligible and falls within measurement error. Among major elements, Si and Ti are the slowest diffusing components, while Na is the fastest. Uphill diffusion minima are observed in Al, Na and some trace elements (Y, Nb, Pb). In contrast to other trace elements, light REE show prominent minima next to the interface between the two melts, with the minimum depth diminishing towards HREE.

From mantle peridotites to hybrid troctolites: Textural, structural and geochemical evolution during multi-stage melt-rock interaction history

NASA Astrophysics Data System (ADS)

Basch, V.; Rampone, E.; Crispini, L.; Ferrando, C.; Ildefonse, B.; Godard, M.

2017-12-01

Recent studies investigate the replacive formation of hybrid troctolites from mantle peridotites after multiple stages of melt-rock reactions. However, none of these studies are conducted in a field-controlled geological setting displaying the clear evolution from peridotite to dunite to troctolite. We investigated the Mt.Maggiore and Erro Tobbio ophiolitic peridotites. They both preserve structural and chemical records of two distinct melt-rock interaction stages, from a reactive melt percolation at spinel facies to plagioclase-bearing melt impregnation at shallower lithospheric depths. We performed EBSD and in situ geochemical analyses to document the textural, structural and geochemical variations of the olivine matrix during melt-rock interactions and the associated evolution from peridotite to dunite to troctolite. The olivine-saturated reactive melt percolation leads to the dissolution of mantle pyroxenes in peridotite, and to the formation of replacive dunite. At shallower level, melt impregnation leads to the crystallization of plagioclase in the dunite, and to the formation of hybrid troctolite. The latter is characterized by textural, structural and geochemical features acquired during dunitization and impregnation processes. We documented a textural evolution of the olivine matrix (decrease in grain area, tortuosity and aspect ratio) during impregnation, with a progressive corrosion of mantle olivines by a reactive melt. As a result, olivine in the hybrid troctolites occurs both as coarse deformed relicts and disrupted undeformed grains. During melt-rock interactions, the variation in olivine Crystallographic Preferred Orientation is related to the local melt/rock ratio involved in the percolation process. At high melt/rock ratio, a change from axial-[100] to axial-[010] is observed, with the disaggregation of the solid matrix. REE-enriched compositions are observed in olivine of dunites and troctolites. A geochemical modeling of melt-rock interactions (Plate Model) fits the observed evolution of modal composition with the measured trace element composition variability. The combined field, structural, and geochemical investigation of the evolution from a mantle protolith to the product of the reactions truly supports the hybrid origin of an olivine-rich troctolite.

Melting and Vaporization of the 1223 Phase in the System (Tl-Pb-Ba-Sr-Ca-Cu-O)

PubMed Central

Cook, L. P.; Wong-Ng, W.; Paranthaman, P.

1996-01-01

The melting and vaporization of the 1223 [(Tl,Pb):(Ba,Sr):Ca:Cu] oxide phase in the system (Tl-Pb-Ba-Sr-Ca-Cu-O) have been investigated using a combination of dynamic methods (differential thermal analysis, thermogravimetry, effusion) and post-quenching characterization techniques (powder x-ray diffraction, scanning electron microscopy, energy dispersive x-ray spectrometry). Vaporization rates, thermal events, and melt compositions were followed as a function of thallia loss from a 1223 stoichiometry. Melting and vaporization equilibria of the 1223 phase are complex, with as many as seven phases participating simultaneously. At a total pressure of 0.1 MPa the 1223 phase was found to melt completely at (980 ± 5) °C in oxygen, at a thallia partial pressure (pTl2O) of (4.6 ± 0.5) kPa, where the quoted uncertainties are standard uncertainties, i.e., 1 estimated standard deviation. The melting reaction involves five other solids and a liquid, nominally as follows: 1223→1212+(Ca,Sr)2CuO3+(Sr,Ca)CuO2+BaPbO3+(Ca,Sr)O+Liquid Stoichiometries of the participating phases have been determined from microchemical analysis, and substantial elemental substitution on the 1212 and 1223 crystallographic sites is indicated. The 1223 phase occurs in equilibrium with liquids from its melting point down to at least 935 °C. The composition of the lowest melting liquid detected for the bulk compositions of this study has been measured using microchemical analysis. Applications to the processing of superconducting wires and tapes are discussed. PMID:27805086

Elemental composition of the Martian crust.

PubMed

McSween, Harry Y; Taylor, G Jeffrey; Wyatt, Michael B

2009-05-08

The composition of Mars' crust records the planet's integrated geologic history and provides clues to its differentiation. Spacecraft and meteorite data now provide a global view of the chemistry of the igneous crust that can be used to assess this history. Surface rocks on Mars are dominantly tholeiitic basalts formed by extensive partial melting and are not highly weathered. Siliceous or calc-alkaline rocks produced by melting and/or fractional crystallization of hydrated, recycled mantle sources, and silica-poor rocks produced by limited melting of alkali-rich mantle sources, are uncommon or absent. Spacecraft data suggest that martian meteorites are not representative of older, more voluminous crust and prompt questions about their use in defining diagnostic geochemical characteristics and in constraining mantle compositional models for Mars.

The origin of Cu/Au ratios in porphyry-type ore deposits.

PubMed

Halter, Werner E; Pettke, Thomas; Heinrich, Christoph A

2002-06-07

Microanalysis of major and trace elements in sulfide and silicate melt inclusions by laser-ablation inductively coupled plasma mass spectrometry indicates a direct link between a magmatic sulfide liquid and the composition of porphyry-type ore deposits. Copper (Cu), gold (Au), and iron (Fe) are first concentrated in a sulfide melt during magmatic evolution and then released to an ore-forming hydrothermal fluid exsolved late in the history of a magma chamber. The composition of sulfide liquids depends on the initial composition and source of the magma, but it also changes during the evolution of the magma in the crust. Magmatic sulfide melts may exert the dominant direct control on the economic metal ratios of porphyry-type ore deposits.

Final report for SERDP WP-2209 Replacement melt-castable formulations for Composition B

DTIC Science & Technology

2017-05-19

Chemical reaction of the materials in the melt ............................................................... 5 Thermal degradation of materials...reasons other than the hazard of explosion, these include: • Chemical reaction of the materials in the melt • Thermal degradation at low...temperature • Sublimation and condensation of explosive material on equipment and exposure to workers Chemical reaction of the materials in the melt

Mineralogy and composition of the oceanic mantle

USGS Publications Warehouse

Putirka, Keith; Ryerson, F.J.; Perfit, Michael; Ridley, W. Ian

2011-01-01

The mineralogy of the oceanic basalt source region is examined by testing whether a peridotite mineralogy can yield observed whole-rock and olivine compositions from (1) the Hawaiian Islands, our type example of a mantle plume, and (2) the Siqueiros Transform, which provides primitive samples of normal mid-ocean ridge basalt. New olivine compositional data from phase 2 of the Hawaii Scientific Drilling Project (HSDP2) show that higher Ni-in-olivine at the Hawaiian Islands is due to higher temperatures (T) of melt generation and processing (by c. 300°C) related to the Hawaiian mantle plume. DNi is low at high T, so parental Hawaiian basalts are enriched in NiO. When Hawaiian (picritic) parental magmas are transported to shallow depths, olivine precipitation occurs at lower temperatures, where DNi is high, leading to high Ni-in-olivine. Similarly, variations in Mn and Fe/Mn ratios in olivines are explained by contrasts in the temperatures of magma processing. Using the most mafic rocks to delimit Siqueiros and Hawaiian Co and Ni contents in parental magmas and mantle source compositions also shows that both suites can be derived from natural peridotites, but are inconsistent with partial melting of natural pyroxenites. Whole-rock compositions at Hawaii and Siqueiros are also matched by partial melting experiments conducted on peridotite bulk compositions. Hawaiian whole-rocks have elevated FeO contents compared with Siqueiros, which can be explained if Hawaiian parental magmas are generated from peridotite at 4-5 GPa, in contrast to pressures of slightly greater than 1 GPa for melt generation at Siqueiros; these pressures are consistent with olivine thermometry, as described in an earlier paper. SiO2-enriched Koolau compositions are reproduced if high-Fe Hawaiian parental magmas re-equilibrate at 1-1·5 GPa. Peridotite partial melts from experimental studies also reproduce the CaO and Al2O3 contents of Hawaiian (and Siqueiros) whole-rocks. Hawaiian magmas have TiO2 contents, however, that are enriched compared with melts from natural peridotites and magmas derived from the Siqueiros depleted mantle, and consequently may require an enriched source. TiO2 is not the only element that is enriched relative to melts of natural peridotites. Moderately incompatible elements, such as Ti, Zr, Hf, Y, and Eu, and compatible elements, such as Yb and Lu, are all enriched at the Hawaiian Islands. Such enrichments can be explained by adding 5-10% mid-ocean ridge basalt (crust) to depleted mantle; when the major element composition of such a mixture is recast into mineral components, the result is a fertile peridotite mineralogy.

Chemistry of Aviation Fuels

NASA Technical Reports Server (NTRS)

Knepper, Bryan; Hwang, Soon Muk; DeWitt, Kenneth J.

2004-01-01

Minimum ignition energies of various methanol/air mixtures were measured in a temperature controlled constant volume combustion vessel using a spark ignition method with a spark gap distance of 2 mm. The minimum ignition energies decrease rapidly as the mixture composition (equivalence ratio, Phi) changes from lean to stoichiometric, reach a minimum value, and then increase rather slowly with Phi. The minimum of the minimum ignition energy (MIE) and the corresponding mixture composition were determined to be 0.137 mJ and Phi = 1.16, a slightly rich mixture. The variation of minimum ignition energy with respect to the mixture composition is explained in terms of changes in reaction chemistry.

Thermodynamic controls on element partitioning between titanomagnetite and andesitic-dacitic silicate melts

NASA Astrophysics Data System (ADS)

Sievwright, R. H.; Wilkinson, J. J.; O'Neill, H. St. C.; Berry, A. J.

2017-08-01

Titanomagnetite-melt partitioning of Mg, Mn, Al, Ti, Sc, V, Co, Ni, Cu, Zn, Ga, Zr, Nb, Mo, Hf and Ta was investigated experimentally as a function of oxygen fugacity ( fO2) and temperature ( T) in an andesitic-dacitic bulk-chemical compositional range. In these bulk systems, at constant T, there are strong increases in the titanomagnetite-melt partitioning of the divalent cations (Mg2+, Mn2+, Co2+, Ni2+, Zn2+) and Cu2+/Cu+ with increasing fO2 between 0.2 and 3.7 log units above the fayalite-magnetite-quartz buffer. This is attributed to a coupling between magnetite crystallisation and melt composition. Although melt structure has been invoked to explain the patterns of mineral-melt partitioning of divalent cations, a more rigorous justification of magnetite-melt partitioning can be derived from thermodynamic principles, which accounts for much of the supposed influence ascribed to melt structure. The presence of magnetite-rich spinel in equilibrium with melt over a range of fO2 implies a reciprocal relationship between a(Fe2+O) and a(Fe3+O1.5) in the melt. We show that this relationship accounts for the observed dependence of titanomagnetite-melt partitioning of divalent cations with fO2 in magnetite-rich spinel. As a result of this, titanomagnetite-melt partitioning of divalent cations is indirectly sensitive to changes in fO2 in silicic, but less so in mafic bulk systems.

Theoretical/best practice energy use in metalcasting operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schifo, J. F.; Radia, J. T.

2004-05-01

This study determined the theoretical minimum energy requirements for melting processes for all ferrous and noferrous engenieering alloys. Also the report details the Best Practice energy consumption for the industry.

Experimental Crystallization of Yamato 980459

NASA Technical Reports Server (NTRS)

Jones, John H.; Galenas, M. G.; Danielson, L. R.

2009-01-01

Currently, only two martian meteorites QUE 94201 (QUE) and Yamato 980459 (Y98) have been experimentally shown to me true melt compositions. Most martian meteorites are instead, cumulates or partial cumulates. We have performed experiments on a Y98 composition to assess whether QUE could be related to Y98 by some fractionation process [1]. Y98 is a basaltic shergottite from the SNC (Shergotty, Nakhla, Chassigny) meteorite group. Y98 is composed of 26% olivine, 48% pyroxene, 25% mesostasis, and no plagioclase [2]. The large size of the olivine megacrysts and absence of plagioclase suggest that the parental melt which formed this meteorite had begun cooling slowly until some mechanism, such as magma ascent, caused rapid cooling [3]. Y98 s olivines have the highest Mg content of all the shergottites suggesting that it is the most primitive [4]. Y98 has been determined to be a melt composition by comparing the composition of experimental liquidus olivines with the composition of the cores of Y98 olivines [4]. The liquidus of Y98 is predicted by MELTS [5] and by experimentation [6] to be 1450 C. Analyses of Y98 show it to be very depleted in LREEs and it has similar depleted patterns as other shergottites such as QUE [7].

Metal/Silicate Partitioning of P, Ga, and W at High Pressures and Temperatures: Dependence on Silicate Melt Composition

NASA Technical Reports Server (NTRS)

Bailey, Edward; Drake, Michael J.

2004-01-01

The distinctive pattern of element concentrations in the upper mantle provides essential evidence in our attempts to understand the accretion and differentiation of the Earth (e.g., Drake and Righter, 2002; Jones and Drake, 1986; Righter et al., 1997; Wanke 1981). Core formation is best investigated through use of metal/silicate partition coefficients for siderophile elements. The variables influencing partition coefficients are temperature, pressure, the major element compositions of the silicate and metal phases, and oxygen fugacity. Examples of studies investigating the effects of these variables on partitioning behavior are: composition of the metal phase by Capobianco et al. (1999) and Righter et al. (1997); silicate melt composition by Watson (1976), Walter and Thibault (1995), Hillgren et al. (1996), Jana and Walker (1997), and Jaeger and Drake (2000); and oxygen fugacity by Capobianco et al. (1999), and Walter and Thibault (1995). Here we address the relative influences of silicate melt composition, pressure and temperature.

Low melting high lithia glass compositions and methods

DOEpatents

Jantzen, Carol M.; Pickett, John B.; Cicero-Herman, Connie A.; Marra, James C.

2003-09-23

The invention relates to methods of vitrifying waste and for lowering the melting point of glass forming systems by including lithia formers in the glass forming composition in significant amounts, typically from about 0.16 wt % to about 11 wt %, based on the total glass forming oxides. The lithia is typically included as a replacement for alkali oxide glass formers that would normally be present in a particular glass forming system. Replacement can occur on a mole percent or weight percent basis, and typically results in a composition wherein lithia forms about 10 wt % to about 100 wt % of the alkali oxide glass formers present in the composition. The present invention also relates to the high lithia glass compositions formed by these methods. The invention is useful for stabilization of numerous types of waste materials, including aqueous waste uranium oxides The decrease in melting point achieved by the present invention desirably prevents volatilization of hazardous or radioactive species during vitrification.

Predicting major element mineral/melt equilibria - A statistical approach

NASA Technical Reports Server (NTRS)

Hostetler, C. J.; Drake, M. J.

1980-01-01

Empirical equations have been developed for calculating the mole fractions of NaO0.5, MgO, AlO1.5, SiO2, KO0.5, CaO, TiO2, and FeO in a solid phase of initially unknown identity given only the composition of the coexisting silicate melt. The approach involves a linear multivariate regression analysis in which solid composition is expressed as a Taylor series expansion of the liquid compositions. An internally consistent precision of approximately 0.94 is obtained, that is, the nature of the liquidus phase in the input data set can be correctly predicted for approximately 94% of the entries. The composition of the liquidus phase may be calculated to better than 5 mol % absolute. An important feature of this 'generalized solid' model is its reversibility; that is, the dependent and independent variables in the linear multivariate regression may be inverted to permit prediction of the composition of a silicate liquid produced by equilibrium partial melting of a polymineralic source assemblage.

Polyimide Composites Based on Asymmetric Dianhydrides (a-ODPA vs a-BPDA)

NASA Technical Reports Server (NTRS)

Chuang, Kathy C.; Criss, Jim M., Jr.; Mintz, Eric A.

2009-01-01

Two series of low-melt viscosity imide resins (2-15 poise at 260-280 C) were formulated from either asymmetric oxydiphthalic anhydride (a-ODPA) or asymmetric biphenyl dianhydride (a- BPDA) with 4-phenylethynyl endcap (PEPA), along with 3,4'-oxydianiline, 3,4 - methylenedianiline, 3,3 -methylenedianiline or 3,3 -diaminobenzophenone, using a solvent-free melt process. These low-melt viscosity imide resins were fabricated into polyimide/T650-35 carbon fabric composites by resin transfer molding (RTM). Composites from a-ODPA based resins display better open-hole compression strength and short beam shear strength from room temperature to 288 C than that of the corresponding a-BPDA based resins. However, due to the lower Tg s of a-ODPA based resins (265-330 C), their corresponding composites do not possess 315 C use capability while the a-BPDA based composites do. In essence, RTM 370 (T g = 370 C), derived from a-BPDA and 3,4 -ODA and PEPA, exhibits the best overall property performance at 315 C (600 F).

First experimental observations on melting and chemical modification of volcanic ash during lightning interaction.

PubMed

Mueller, S P; Helo, C; Keller, F; Taddeucci, J; Castro, J M

2018-01-23

Electrification in volcanic ash plumes often leads to syn-eruptive lightning discharges. High temperatures in and around lightning plasma channels have the potential to chemically alter, re-melt, and possibly volatilize ash fragments in the eruption cloud. In this study, we experimentally simulate temperature conditions of volcanic lightning in the laboratory, and systematically investigate the effects of rapid melting on the morphology and chemical composition of ash. Samples of different size and composition are ejected towards an artificially generated electrical arc. Post-experiment ash morphologies include fully melted spheres, partially melted particles, agglomerates, and vesiculated particles. High-speed imaging reveals various processes occurring during the short lightning-ash interactions, such as particle melting and rounding, foaming, and explosive particle fragmentation. Chemical analyses of the flash-melted particles reveal considerable bulk loss of Cl, S, P and Na through thermal vaporization. Element distribution patterns suggest convection as a key process of element transport from the interior of the melt droplet to rim where volatiles are lost. Modeling the degree of sodium loss delivers maximum melt temperatures between 3290 and 3490 K. Our results imply that natural lighting strikes may be an important agent of syn-eruptive morphological and chemical processing of volcanic ash.

The Extra Flask

NASA Astrophysics Data System (ADS)

Thielemann, R.

1981-05-01

It seemed quite natural and logical for me to want to address such an informed group about some of the many superalloys developed over the past forty years-but then I realized that most, if not all of them are listed with their compositions and properties in the ASM Metals Handbook, so this subject did not seem promising. At this point I started to think about the many new and important developments in processing techniques that made the melting, casting, and forming of the alloys possible. It seemed to me that the new procedures were, in most every instance, just as important as the new compositions themselves. Without the new techniques, many of the higher strength compositions were difficult, if not impossible to produce by existing procedures. Certainly, vacuum induction melting allowed us to melt and cast the titanium-and aluminum-bearing compositions without incurring the usual oxide and nitride inclusions.

High Temperature Transfer Molding Resins Based on 2,3,3',4'-Biphenyltetracarboxylic Dianhydride

NASA Technical Reports Server (NTRS)

Smith, J. G., Jr.; Connell, J. W.; Hergenrother, P. M.; Yokota, R.; Criss, J. M.

2002-01-01

As part of an ongoing effort to develop materials for resin transfer molding (RTM) processes to fabricate high performance/high temperature composite structures, phenylethynyl containing imides have been under investigation. New phenylethynyl containing imide compositions were prepared using 2,3,3',4'-biphenyltetracarboxylic dianhydride (a-BPDA) and evaluated for cured glass transition temperature (Tg), melt flow behavior, and for processability into flat composite panels via RTM. The a-BPDA imparts a unique combination of properties that are desirable for high temperature transfer molding resins. In comparison to its symmetrical counterpart (i.e. 3,3',4,4'-biphenyltetracarboxylic dianhydride), a-BPDA affords oligomers with lower melt viscosities and when cured, higher Tgs. Several candidates exhibited the appropriate combination of properties such as a low and stable melt viscosity required for RTM processes, high cured Tg, and moderate toughness. The chemistry, physical, and composite properties of select resins will be discussed.

Effect of Cooling Rate and Oxygen Fugacity on the Crystallization of the Queen Alexandra Range 94201 Martian Melt Composition

NASA Technical Reports Server (NTRS)

Koizumi, E.; Mikouchi, T.; McKay, G.; Schwandt, C.; Monkawa, A.; Miyamoto, M.

2002-01-01

Although many basaltic shergottites have been recently found in north African deserts, QUE94201 basaltic shergottite (QUE) is still important because of its particular mineralogical and petrological features. This meteorite is thought to represent its parent melt composition [1 -3] and to crystallize under most reduced condition in this group [1,4]. We performed experimental study by using the synthetic glass that has the same composition as the bulk of QUE. After homogenization for 48 hours at 1300 C, isothermal and cooling experiments were done under various conditions (e.g. temperature, cooling rates, and redox states). Our goals are (1) to verify that QUE really represents its parent melt composition, (2) to estimate a cooling rate of this meteorite, (3) to clarify the crystallization sequences of present minerals, and (4) to verity that this meteorite really crystallized under reduced condition.

Worldwide occurrence of silica-rich melts in sub-continental and sub-oceanic mantle minerals

NASA Astrophysics Data System (ADS)

Schiano, P.; Clocchiatti, R.

1994-04-01

ROCK samples derived from the Earth's upper mantle commonly show indirect evidence for chemical modification. Such modification, or 'metasomatism', can be recognized by the precipitation of exotic minerals such as phlogopite, amphibole or apatite1, and by the overprinting of the bulk compositions of the mantle rocks by a chemical signature involving the enrichment of potassium and other 'incompatible' elements2. Here we study the composition of the metasomatic agents more directly by examining melt and fluid inclusions trapped in mantle minerals. These inclusions are secondary, forming trails along healed fracture planes. A systematic study of the chemical compositions and entrapment temperatures and pressures of inclusions from 14 ultramaflc peridotites from both continental and oceanic intraplate regions shows that volatile- and silica-rich metasomatic melts are present throughout the litho-sphere. Their compositions, which differ dramatically from those of erupted, mantle-derived magmas, are more akin to continental than to oceanic crust.

Use of olivine and plagioclase saturation surfaces for the petrogenetic modeling of recrystallized basic plutonic systems

NASA Technical Reports Server (NTRS)

Hanson, G. N.

1983-01-01

During petrogenetic studies of basic plutonic rocks, there are at least three major questions to be considered: (1) what were the relative proportions of cumulate crystals and intercumulus melt in a given sample? (2) what is the composition and variation in composition of the melts within the pluton? and (3) what is the original composition of the liquids, their source and evolution prior to the time of emplacement? Use of both saturation surfaces can place strong limits on the compositions of potential cumulate phases and intercumulus melts. Consideration of appropriate trace elements can indicate whether a sample is an orthocumulate, adcumulate or mesocumulate. Thus, when trace element and petrographic data are considered together with the saturation surfaces, it should be possible to begin to answer the three major questions given above, even for strongly recrystallized basic plutons.

SLUDGE BATCH 4 BASELINE MELT RATE FURNACE AND SLURRY-FED MELT RATE FURNACE TESTS WITH FRITS 418 AND 510 (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M. E.; Jones, T. M.; Miller, D. H.

Several Slurry-Fed Melt Rate Furnace (SMRF) tests with earlier projections of the Sludge Batch 4 (SB4) composition have been performed.1,2 The first SB4 SMRF test used Frits 418 and 320, however it was found after the test that the REDuction/OXidation (REDOX) correlation at that time did not have the proper oxidation state for manganese. Because the manganese level in the SB4 sludge was higher than previous sludge batches tested, the impact of the higher manganese oxidation state was greater. The glasses were highly oxidized and very foamy, and therefore the results were inconclusive. After resolving this REDOX issue, Frits 418,more » 425, and 503 were tested in the SMRF with the updated baseline SB4 projection. Based on dry-fed Melt Rate Furnace (MRF) tests and the above mentioned SMRF tests, two previous frit recommendations were made by the Savannah River National Laboratory (SRNL) for processing of SB4 in the Defense Waste Processing Facility (DWPF). The first was Frit 503 based on the June 2006 composition projections.3 The recommendation was changed to Frit 418 as a result of the October 2006 composition projections (after the Tank 40 decant was implemented as part of the preparation plan). However, the start of SB4 processing was delayed due to the control room consolidation outage and the repair of the valve box in the Tank 51 to Tank 40 transfer line. These delays resulted in changes to the projected SB4 composition. Due to the slight change in composition and based on preliminary dry-fed MRF testing, SRNL believed that Frit 510 would increase throughput in processing SB4 in DWPF. Frit 418, which was used in processing Sludge Batch 3 (SB3), was a viable candidate and available in DWPF. Therefore, it was used during the initial SB4 processing. Due to the potential for higher melt rates with Frit 510, SMRF tests with the latest SB4 composition (1298 canisters) and Frits 510 and 418 were performed at a targeted waste loading (WL) of 35%. The '1298 canisters' describes the number of equivalent canisters that would be produced from the beginning of the current contract period before SB3 is blended with SB4. The melt rate for the SMRF SB4/Frit 510 test was 14.6 grams/minute. Due to cold cap mounding problems with the SMRF SB4/Frit 418 feed at 50 weight % solids that prevented a melt rate determination, this feed was diluted to 45 weight % solids. The melt rate for this diluted feed was 8.9 grams/minute. A correction factor of 1.2 for estimating the melt rate at 50 weight % solids from 45 weight % solids test results (based on previous SMRF testing5) was then used to estimate a melt rate of 10.7 grams/minute for SB4/Frit 418 at 50 weight % solids. Therefore, the use of Frit 510 versus Frit 418 with SB4 resulted in a higher melt rate (14.6 versus an estimated 10.7 grams/minute). For reference, a previous SMRF test with SB3/Frit 418 feed at 35% waste loading and 50 weight % solids resulted in a melt rate of 14.1 grams/minute. Therefore, depending on the actual feed rheology, the use of Frit 510 with SB4 could result in similar melt rates as experienced with SB3/Frit 418 feed in the DWPF.« less

Effect of accelerated crucible rotation on melt composition in high-pressure vertical Bridgman growth of cadmium zinc telluride

NASA Astrophysics Data System (ADS)

Yeckel, Andrew; Derby, Jeffrey J.

2000-02-01

Three-dimensional axisymmetric, time-dependent simulations of the high-pressure vertical Bridgman growth of large-diameter cadmium zinc telluride are performed to study the effect of accelerated crucible rotation (ACRT) on crystal growth dynamics. The model includes details of heat transfer, melt convection, solid-liquid interface shape, and dilute zinc segregation. Application of ACRT greatly improves mixing in the melt, but causes an overall increased deflection of the solid-liquid interface. The flow exhibits a Taylor-Görtler instability at the crucible sidewall, which further enhances melt mixing. The rate of mixing depends strongly on the length of the ACRT cycle, with an optimum half-cycle length between 2 and 4 Ekman time units. Significant melting of the crystal occurs during a portion of the rotation cycle, caused by periodic reversal of the secondary flow at the solid-liquid interface, indicating the possibility of compositional striations.

Impact melt breccias at the Apollo 17 landing site

NASA Technical Reports Server (NTRS)

Ryder, Graham

1992-01-01

Impact melt breccias are by far the most common highland rock type collected on the Apollo 17 mission. They tend to be fine grained, with virtually no clast-free impact melt rocks having been identified. All the highland boulders sampled are impact melt breccia, with the possible exception of one South Massif boulder that might have a friable matrix (but nonetheless consists dominantly of impact melt) and a shocked igneous norite boulder from the North Massif. The impact melt breccias were originally described as metaclastic, but their melt origin became apparent as work progressed. Chemical compositions appear to allow natural groupings of the impact melt breccias. Various groupings of the impact melt breccias are discussed.

Texturing by cooling a metallic melt in a magnetic field.

PubMed

Tournier, Robert F; Beaugnon, Eric

2009-02-01

Processing in a magnetic field leads to the texturing of materials along an easy-magnetization axis when a minimum anisotropy energy exists at the processing temperature; the magnetic field can be applied to a particle assembly embedded into a liquid, or to a solid at a high diffusion temperature close to the melting temperature or between the liquidus and the solidus temperatures in a region of partial melting. It has been shown in many experiments that texturing is easy to achieve in congruent and noncongruent compounds by applying the field above the melting temperature T m or above the liquidus temperature of alloys. Texturing from a melt is successful when the overheating temperature is just a few degrees above T m and fails when the processing time above T m is too long or when the overheating temperature is too high; these observations indicate the presence of unmelted crystals above T m with a size depending on these two variables that act as growth nuclei. A recent model that predicts the existence of unmelted crystals above the melting temperature is used to calculate their radius in a bismuth melt.

Phase diagram of Ag-Pd bimetallic nanoclusters by molecular dynamics simulations: solid-to-liquid transition and size-dependent behavior.

PubMed

Kim, Da Hye; Kim, Hyun You; Ryu, Ji Hoon; Lee, Hyuck Mo

2009-07-07

This report on the solid-to-liquid transition region of an Ag-Pd bimetallic nanocluster is based on a constant energy microcanonical ensemble molecular dynamics simulation combined with a collision method. By varying the size and composition of an Ag-Pd bimetallic cluster, we obtained a complete solid-solution type of binary phase diagram of the Ag-Pd system. Irrespective of the size and composition of the cluster, the melting temperature of Ag-Pd bimetallic clusters is lower than that of the bulk state and rises as the cluster size and the Pd composition increase. Additionally, the slope of the phase boundaries (even though not exactly linear) is lowered when the cluster size is reduced on account of the complex relations of the surface tension, the bulk melting temperature, and the heat of fusion. The melting of the cluster initially starts at the surface layer. The initiation and propagation of a five-fold icosahedron symmetry is related to the sequential melting of the cluster.

Estimation of Melt Ponds over Arctic Sea Ice using MODIS Surface Reflectance Data

NASA Astrophysics Data System (ADS)

Ding, Y.; Cheng, X.; Liu, J.

2017-12-01

Melt ponds over Arctic sea ice is one of the main factors affecting variability of surface albedo, increasing absorption of solar radiation and further melting of snow and ice. In recent years, a large number of melt ponds have been observed during the melt season in Arctic. Moreover, some studies have suggested that late spring to mid summer melt ponds information promises to improve the prediction skill of seasonal Arctic sea ice minimum. In the study, we extract the melt pond fraction over Arctic sea ice since 2000 using three bands MODIS weekly surface reflectance data by considering the difference of spectral reflectance in ponds, ice and open water. The preliminary comparison shows our derived Arctic-wide melt ponds are in good agreement with that derived by the University of Hamburg, especially at the pond distribution. We analyze seasonal evolution, interannual variability and trend of the melt ponds, as well as the changes of onset and re-freezing. The melt pond fraction shows an asymmetrical growth and decay pattern. The observed melt ponds fraction is almost within 25% in early May and increases rapidly in June and July with a high fraction of more than 40% in the east of Greenland and Beaufort Sea. A significant increasing trend in the melt pond fraction is observed for the period of 2000-2017. The relationship between melt pond fraction and sea ice extent will be also discussed. Key Words: melt ponds, sea ice, Arctic

Clapeyron slope reversal in the melting curve of AuGa2 at 5.5 GPa.

PubMed

Geballe, Z M; Raju, S V; Godwal, B K; Jeanloz, R

2013-10-16

We use x-ray diffraction in a resistively heated diamond anvil cell to extend the melting curve of AuGa2 beyond its minimum at 5.5 GPa and 720 K, and to constrain the high-temperature phase boundaries between cubic (fluorite structure), orthorhombic (cottunite structure) and monoclinic phases. We document a large change in Clapeyron slope that coincides with the transitions from cubic to lower symmetry phases, showing that a structural transition is the direct cause of the change in slope. In addition, moderate (~30 K) to large (90 K) hysteresis is detected between melting and freezing, from which we infer that at high pressures, AuGa2 crystals can remain in a metastable state at more than 5% above the thermodynamic melting temperature.

The evolution of continental roots in numerical thermo-chemical mantle convection models including differentiation by partial melting

NASA Astrophysics Data System (ADS)

de Smet, J. H.; van den Berg, A. P.; Vlaar, N. J.

1999-09-01

Incorporating upper mantle differentiation through decompression melting in a numerical mantle convection model, we demonstrate that a compositionally distinct root consisting of depleted peridotite can grow and remain stable during a long period of secular cooling. Our modeling results show that in a hot convecting mantle partial melting will produce a compositional layering in a relatively short time of about 50 Ma. Due to secular cooling mantle differentiation finally stops before 1 Ga. The resulting continental root remains stable on a billion year time scale due to the combined effects of its intrinsically lower density and temperature-dependent rheology. Two different parameterizations of the melting phase-diagram are used in the models. The results indicate that during the Archaean melting occurred on a significant scale in the deep regions of the upper mantle, at pressures in excess of 15 GPa. The compositional depths of continental roots extend to 400 km depending on the potential temperature and the type of phase-diagram parameterization used in the model. The results reveal a strong correlation between lateral variations of temperature and the thickness of the continental root. This shows that cold regions in cratons are stabilized by a thick depleted root.

Evolution of Shock Melt Compositions in Lunar Regoliths

NASA Technical Reports Server (NTRS)

Vance, A. M.; Christoffersen, R.; Keller, L. P.; Berger, E. L.; Noble, S. K.

2016-01-01

Space weathering processes - driven primarily by solar wind ion and micrometeorite bombardment, are constantly changing the surface regoliths of airless bodies, such as the Moon. It is essential to study lunar soils in order to fully under-stand the processes of space weathering, and how they alter the optical reflectance spectral properties of the lunar surface relative to bedrock. Lunar agglutinates are aggregates of regolith grains fused together in a glassy matrix of shock melt produced during micrometeorite impacts into the lunar regolith. The formation of the shock melt component in agglutinates involves reduction of Fe in the target material to generate nm-scale spherules of metallic Fe (nanophase Fe0 or npFe0). The ratio of elemental Fe, in the form of npFe0, to FeO in a given bulk soil indicates its maturity, which increases with length of surface exposure as well as being typically higher in the finer-size fraction of soils. The melting and mixing process in agglutinate formation remain poorly understood. This includes incomplete knowledge regarding how the homogeneity and overall compositional trends of the agglutinate glass portions (agglutinitic glass) evolve with maturity. The aim of this study is to use sub-micrometer scale X-ray compositional mapping and image analysis to quantify the chemical homogeneity of agglutinitic glass, correlate its homogeneity to its parent soil maturity, and identify the principal chemical components contributing to the shock melt composition variations. An additional focus is to see if agglutinitic glass contains anomalously high Fe sub-micron scale compositional domains similar to those recently reported in glassy patina coatings on lunar rocks.

In situ determination of binary alloy melt compositions in the LHDAC by X- Radiography

NASA Astrophysics Data System (ADS)

Lord, O. T.; Walter, M. J.; Walker, D.; Clark, S. M.

2008-12-01

Constraining the light element in Earth's molten outer core requires an understanding of the melting phase relations in iron-light element binary systems. For example, it is critical to determine the composition of liquids at binary eutectics. Typically such measurements are carried out after the sample has been quenched in temperature and pressure. Such 'cook and look' methods possibly suffer from systematic errors introduced by exsolution of the light element from the melt on quench and error in the reintegration of the liquid composition [1]. Here, we present a novel method for the determination of melt compositions in iron-light element binary systems in situ in the LHDAC at simultaneous high-pressure, high-temperature conditions. Samples consist of a light element bearing compound, such as FeO, surrounded by a pure iron ring, forming a donut ~100 μm in diameter and ~15 μm thick. The donuts are loaded into stainless steel gaskets in the DAC, sandwiched between discs fabricated from sol-gel deposited nanocrystalline Al2O3 with similar dimensions to the donut. Pressure is monitored by ruby fluorescence during compression. The sample is heated at the boundary between the iron and light element compound using two 100 W IR lasers in a double-sided configuration at beamline 12.2.2 at the Advanced Light Source. Temperature is measured by spectroradiometry. Before, during and after melting, X-radiographic images of the sample are taken by shining a defocused beam of synchrotron X-rays through the sample and onto a CdWO4 phosphor. The visible light from the phosphor is then focused onto a high resolution CCD, where absorption contrast images are recorded. The absorption of the molten region is then determined, and it's composition calculated by linear interpolation between the absorption of the two solid end members. As a test of the reliability of the method we measured the Fe-FeS eutectic to 20 GPa and our results are in good agreement with previous studies that are based on various ex situ techniques. We measured the eutectic composition between Fe and Fe3C up to 44 GPa, and found that the carbon content of the eutectic drops rapidly above about 10 GPa, dropping to less that 1 wt% by 44 GPa. This result is generally consistent with the thermodynamic calculations of Wood [2]. Experiments on the Fe-FeSi eutectic yielded an increase in the Si content of the eutectic to 35 GPa, consistent with data from large volume press experiments [3] Notably, melting experiments at 35-43 GPa and ~2500 K on a boundary between Fe and FeO failed to yield evidence of a melt with a composition distinguishable from pure iron. However, an experiment at 12 GPa and 2700 K between Fe and FeO(OH) did yield a melt with a composition intermediate between the two end members. This suggests that O solubility in the Fe-O eutectic melt is low at mid-mantle pressures, but that H may dissolve into the melt by itself or in combination with O. [1] Walker, D., 2005. Core-Mantle chemical issues. Canad. Min., 43, 1553-1564 [2] Wood, B. J., 1993. Carbon in the core. Earth Planet Sci. Lett., 117, 593-607 [3] Kuwayama, Y. & Hirose, K., 2004. Phase relations in the system Fe-FeSi at 21 GPa. Am. Min., 89, 273-276.

Early Earth Felsic Crust Formation: Insights from Numerical Modelling of High-MgO Archaean Basalt Partial Melting

NASA Astrophysics Data System (ADS)

Riel, N., Jr.

2015-12-01

The Tonalite-Trondhjemite-Granodiorite series (TTGs) represent the bulk of the felsic continental crust that formed between 4.4 and 2.5 Ga and is preserved in Archaean craton (3.8-2.5 Ga). It is now recognized that the petrogenesis of TTG series derives from an hydrous mafic system at high pressure. However, the source of the early TTGs (3.5-3.2 Ga) have not been preserved and its characteristics are still debated. In this study we use thermodynamical modelling coupled with two-phase flow to investigate the products of partial melting of high-MgO primary mafic crust. Our model setup is made of a 45-km thick hydrated mafic crust and is heated above the solidus from 50 to 200°C. To explore the effects of melt-rock interactions during melt transfer (via two-phase flow), the melt composition is modelled either in thermodynamic equilibrium with the rock or in thermodynamic disequilibrium. Our modelling results show that partial melting of hydrous high-MgO metabasalt crust can produce significant volumes of felsic melt. The average composition of these melts is SiO2-rich > 62%, Mg# = 40-50, Na2O ~6%, MgO = 0.5-1% which is consistent with the composition of TTGs. The residual rock after melt segregation is composed of olivine + garnet + pyroxene which is in agreement with Archaean eclogites found in mantle xenoliths of Archaean cratons. Moreover, the depleted residual rock is denser than the mantle and is likely to be recycled in the mantle. We show that the early felsic crust with a TTGs signature could have been formed by partial melting of high-MgO hydrated metabasaltic crust, and propose that plume-related activity and/or rapid burial due to high volcanic activity are likely geodynamic conditions to generate an early felsic crust.

Heterogeneous mineral assemblages in martian meteorite Tissint as a result of a recent small impact event on Mars

NASA Astrophysics Data System (ADS)

Walton, E. L.; Sharp, T. G.; Hu, J.; Filiberto, J.

2014-09-01

The microtexture and mineralogy of shock melts in the Tissint martian meteorite were investigated using scanning electron microscopy, Raman spectroscopy, transmission electron microscopy and synchrotron micro X-ray diffraction to understand shock conditions and duration. Distinct mineral assemblages occur within and adjacent to the shock melts as a function of the thickness and hence cooling history. The matrix of thin veins and pockets of shock melt consists of clinopyroxene + ringwoodite ± stishovite embedded in glass with minor Fe-sulfide. The margins of host rock olivine in contact with the melt, as well as entrained olivine fragments, are now amorphosed silicate perovskite + magnesiowüstite or clinopyroxene + magnesiowüstite. The pressure stabilities of these mineral assemblages are ∼15 GPa and >19 GPa, respectively. The ∼200-μm-wide margin of a thicker, mm-size (up to 1.4 mm) shock melt vein contains clinopyroxene + olivine, with central regions comprising glass + vesicles + Fe-sulfide spheres. Fragments of host rock within the melt are polycrystalline olivine (after olivine) and tissintite + glass (after plagioclase). From these mineral assemblages the crystallization pressure at the vein edge was as high as 14 GPa. The interior crystallized at ambient pressure. The shock melts in Tissint quench-crystallized during and after release from the peak shock pressure; crystallization pressures and those determined from olivine dissociation therefore represent the minimum shock loading. Shock deformation in host rock minerals and complete transformation of plagioclase to maskelynite suggest the peak shock pressure experienced by Tissint ⩾ 29-30 GPa. These pressure estimates support our assessment that the peak shock pressure in Tissint was significantly higher than the minimum 19 GPa required to transform olivine to silicate perovskite plus magnesiowüstite. Small volumes of shock melt (<100 μm) quench rapidly (0.01 s), whereas thermal equilibration will occur within 1.2 s in larger volumes of melt (1 mm2). The apparent variation in shock pressure recorded by variable mineral assemblages within and around shock melts in Tissint is consistent with a shock pulse on the order of 10-20 ms combined with a longer duration of post-shock cooling and complex thermal history. This implies that the impact on Mars that shocked and ejected Tissint at ∼1 Ma was not exceptionally large.

Evolution of the Campanian Ignimbrite Magmatic System I: Constraints on Compositional Zonation and Eruption Probability Imposed By Phase Equilibria

NASA Astrophysics Data System (ADS)

Fowler, S.; Spera, F.; Bohrson, W.; Belkin, H.; Devivo, B.

2005-12-01

The eruption and deposition of the ~39.3 ka Campanian Ignimbrite (CI), a large volume (~200 km3 DRE) trachytic to phonolitic ignimbrite, is the dominant event in the history of the Campi Flegrei volcanic field near Naples, Italy. In an effort to comprehend its petrological evolution, we have conducted ~~110 MELTS (Ghiorso, 1997) phase equilibria simulations of the major element evolution of parental CI magma. The goals of this work are to approximate oxygen fugacity (fO2), initial dissolved water content and pressure at which isobaric closed system fractional crystallization of parental melt most accurately captures the observed liquid line of descent and to study the implications of heat extraction from parental CI magma with respect to the origin of compositional zonation and the probability of explosive eruption. Although the CI magma body did not evolve as a perfectly closed system, this assumption allows quantitative insight into magma-host rock mass exchange using trace element and isotopic data (see companion contribution by Bohrson et al.). The parental melt composition was reconstructed using data for melt inclusions trapped within CI clinopyroxene phenocrysts reported by Webster et al. (2003), while allowing for reaction between parental melt and clinopyroxene host. The inferred parental melt is a basaltic trachyandesite. The search space for pressure, (fO2) and initial dissolved H2O was 0.1-0.5 in 0.05 GPa increments, QFM-1 to QFM+3 and 1, 2 and 3 wt. % H2O, respectively. The criteria used to judge the quality of a simulation include correspondence of the MELTS prediction with CI liquid and phenocryst compositions. Results indicate that a good first-order model involves evolution from a basaltic trachyandesite parent by isobaric (~0.15 GPa) crystal fractionation initially containing ~3 wt% dissolved H2O along the QFM+1 buffer. H2O first saturates at 1127°C at 0.15 GPa when the dissolved water content is ~4 wt %. A striking result is the discovery of a pseudo-invariant point at ~883°C (Tip) and 0.15 GPa. The fraction of melt changes abruptly from ~0.5 to ~0.1 at Tip due to the simultaneous crystallization of alkali feldspar, plagioclase, spinel, biotite and apatite. At Tip, there is a dramatic decrease in the viscosity of melt (by a factor of four) and magma density (~5%) and an increase in the dissolved H2O content of the melt (from 4.4-5.1 wt%) and in the volume fraction,θ, of supercritical fluid in the multiphase system. In particular, θ increases from ~0.05 at 885°C to ~0.6 at 882°C. The liquid composition also changes discontinuously at Tip with Si, Na, and H2O increasing and K and Al decreasing as temperature falls below Tip. The marked variations in composition and properties of volatile-saturated melt and magma were the trigger that led to the catastrophic eruption and formation of the compositionally-zoned CI magma. Because phase equilibria modeling provides information on the enthalpy changes associated with fractional crystallization and because the dimensions of the CI magma chamber and heat extraction rate can be approximated, a time scale for CI magmatic evolution can be derived. The estimated crystallization duration (τ) is10-100 ka and 75% of τ is spent at or near Tip.

What do we really know about Earth's early crust?

NASA Astrophysics Data System (ADS)

Rudnick, R. L.; Tang, M.

2016-12-01

The oldest minerals on Earth, the detrital Hadean Jack Hills zircons from western Australia, show evidence for their crystallization from hydrous, low temperature, granitic magmas. However, considerable debate centers on whether the parental melts are minimum-melt granites formed in subduction zone settings and implying widespread, evolved continental crust (e.g., Harrison, 2009, AREPS), or crystallized from the last differentiates of mafic magmas (Darling et al., 2009, Geology), or even late differentiates of impact melt sheets on a largely water-covered Earth (Kenny et al., 2016, Geology). Another means by which to interrogate the nature of Earth's early crust is through analyses of ancient fine-grained terrigenous sedimentary rocks such as shales or glacial diamictites, which provide averages of the surface of the Earth that is exposed to chemical weathering and erosion. From these studies it has long been known that Archean crust contained a higher proportion of mafic rocks. However, only recently has that proportion been constrained based on a change in the average MgO content of the upper continental crust from 15 wt.% at 3.2 Ga, to 4 wt.% at 2.6 Ga (Tang et al., 2016, Science). These data for terrigeneous sediments require the pre 3.2 Ga crust to be dominated by mafic rocks (only 10-40% `granite' s.l.) and to be high-standing and susceptible to subareal weathering and erosion, implying the mafic crust was thick (see Tang and Rudnick, this meeting). The dramatic transition that occurred in upper crustal composition between 3.2 and 2.6 Ga likely marks the onset of widespread subduction as a means of generating voluminous granite.

Trace element distributions in primitive achondrites

NASA Technical Reports Server (NTRS)

Davis, Andrew M.; Prinz, Martin; Weisberg, Michael K.

1993-01-01

The primitive achondrites have approximately chondritic bulk chemical composition but achondritic textures. Clayton et al. show that nine of these meteorites, the acapulcoites and the lodranites, have similar oxygen isotopic compositions. The acapulcoites appear to be highly metamorphosed, but undifferentiated meteorites of chondritic composition; whereas, the lodranites appear to have lost a feldspathic partial melt. In order to learn more about metamorphic processes and partial melt removal, we have measured the trace element compositions of constituent phases of a number of primitive achondrites by ion microprobe. We have analyzed two acapulcoites, Acapulco and ALH81261 (paired with ALH77081), and three londranites, Lodran, LEW88280, and MAC88177. In addition, we analyzed LEW88663, which has the bulk composition, mineral chemistry, and oxygen isotopic composition of L-chondrites, but is metal-free and has an achondrite texture; and Divnoe, a plagioclase-poor, olivine-rich primitive achondrite with an oxygen isotopic composition similar to that of the group IAB iron meteorites. These meteorites show a variety of REE patterns in their constituent phases, and there are consistent differences between acapulcoites and lodranites that are consistent with removal of a LREE- and Eu-enriched melt that is apparently responsible for the low plagioclase content of lodranites.

Preparation and characterization of acorn starch/poly(lactic acid) composites modified with functionalized vegetable oil derivates.

PubMed

Li, Shouhai; Xia, Jianling; Xu, Yuzhi; Yang, Xuejuan; Mao, Wei; Huang, Kun

2016-05-20

Composites of acorn starch (AS) and poly(1actic acid) (PLA) modified with dimer fatty acid (DFA) or dimer fatty acid polyamide (DFAPA) were produced by a hot-melt extrusion method. The effects of DFA and DFAPA contents on the mechanical, hydrophobic, thermal properties and melt fluidity of the composites were studied under an invariable AS-to-PLA mass ratio of 40/60. SEM and DMA research results show that the compatibility of AS/PLA composites are determined by the dosage of DFA or DFAPA. The hydrophobicity and melt fluidity of composites are improved with the addition of DFA and DFAPA. The glass transition temperatures of the composites are all reduced remarkably by additives DFA and DFAPA. However, DFA and DFAPA exert different effects on the mechanical properties of AS/PLA composites. In the DFAPA-modified system, the tensile and flexural strength first increase and then decrease with the increase of DFAPA dosage; the mechanical strength is maximized when the dosage of DFAPA is 2 wt% of total weight. In the DFA-modified system, the tensile and flexural strength decrease with the increase of DFA dosage. Copyright © 2016 Elsevier Ltd. All rights reserved.

Partial melting of granitoids under eclogite-facies conditions: nanogranites from felsic granulites from Orlica-Śnieżnik Dome (Bohemian Massif)

NASA Astrophysics Data System (ADS)

Ferrero, Silvio; O'Brien, Patrick; Walczak, Katarzyna; Wunder, Bernd; Hecht, Lutz

2014-05-01

Melt inclusions (MI) study in migmatites is a powerful tool to retrieve the original composition of the anatectic melt, both as major elements (Ferrero et al., 2012) and fluid contents (Bartoli et al., 2013). Crystallized MI, or "nanogranites" (Cesare et al., 2009), were identified within HP felsic granulites from Orlica-Śnieżnik Dome, NE Bohemian Massif (Walczak, 2011). The investigated samples are Grt+Ky leucogranulites originated from a granitic protolith, with assemblage Qtz+Pl+Kfs+Grt+Ky+Ttn+Rt+Ilm. Nanogranites occur in garnet as primary inclusions, and consist of Qtz+Ab+Bt+Kfs±Ep±Ap. Such assemblage results from the crystallization of a melt generated during a partial melting reaction; the same reaction is also responsible for the production of the host garnet, interpreted therefore as a peritectic phase. Besides nanogranites, former presence of melt is supported by the occurrence of tiny pseudomorphs of melt-filled pores (Holness & Sawyer, 2008) and euhedral faces in garnet. Garnet composition, with Grs =0.28-0.31, phase assemblage (kyanite, ternary feldspar) and classic thermobarometry suggest that partial melting took place at T≥875°C and P~2.2-2.6 GPa, under eclogite-facies conditions. Although other authors reported palisade quartz after coesite in this area (see e.g. Bakun-Czubarow, 1992), no clear evidence of UHP conditions have been identified during this study. Piston cylinder re-homogenization experiments were performed on MI-bearing garnet chips to obtain the composition of the pristine anatectic melt. The first data from experiments in the range 850-950°C and 2-2.2 GPa show that nanogranites can be re-melted at T≥875°. However, homogenization has not been reached yet since new Grt, with lower CaO and higher MgO, crystallizes on the walls of the inclusion. As P increases, the modal amount of new phase decreases, while its composition evolves closer to those of the host garnet. Further experiments at higher pressure are in underway, with the aim to achieve full re-homogenization and reproduce the system garnet+melt present during anatexis. References Bakun-Czubarow, N., 1992. Quartz pseudomorphs after coesite and quartz exsolutions in eclogitic omphacites of the Zlote Mountains in the Sudetes, SW Poland. Archeological Mineralogy, 48, 3-25. Bartoli, O., Cesare, B., Poli, S., Bodnar, R.J., Acosta-Vigil, A., Frezzotti, M.L. & Meli, S., 2013. Recovering the composition of melt and the fluid regime at the onset of crustal anatexis and S-type granite formation. Geology, 41, 115-118. Cesare, B., Ferrero, S., Salvioli-Mariani, E., Pedron, D. & Cavallo, A., 2009. Nanogranite and glassy inclusions: the anatectic melt in migmatites and granulites. Geology, 37, 627-630. Ferrero, S., Bartoli, O., Cesare, B., Salvioli Mariani, E., Acosta-Vigil, A., Cavallo, A., Groppo, C. & Battiston, S., 2012. Microstructures of melt inclusions in anatectic metasedimentary rocks. Journal of Metamorphic Geology, 30, 303-322. Holness, M.B. & Sawyer, E.W., 2008. On the pseudomorphing of melt-filled pores during the crystallization of migmatites. Journal of Petrology, 49, 1343-1363. Walczak, K., 2011. "Interpretation of Sm-Nd and Lu-Hf dating of garnets from high pressure and high temperature rocks in the light of the trace elements distribution." Doctoral dissertation, Institute of Geological Sciences, Polish Academy of Sciences, Poland.

Melt densities in the CaO-FeO-Fe 2O 3-SiO 2 system and the compositional dependence of the partial molar volume of ferric iron in silicate melts

NASA Astrophysics Data System (ADS)

Dingwell, Donald B.; Brearley, Mark

1988-12-01

The densities of 10 melts in the CaO-FeO-Fe 2O 3-SiO 2 system were determined in equilibrium with air, in the temperature range of 1200 to 1550°C, using the double-bob Archimedean technique. Melt compositions range from 6 to 58 wt% SiO 2, 14 to 76 wt% Fe 2O 3 and 10 to 46 wt% CaO. The ferric-ferrous ratios of glasses drop-quenched from loop fusion equilibration experiments were determined by 57Fe Mössbauer spectroscopy. Melt densities range from 2.689 to 3.618 gm/cm 3 with a mean standard deviation from replicate experiments of 0.15%. Least-squares regressions of molar volume versus molar composition have been performed and the root mean squared deviation shows that a linear combination of partial molar volumes for the oxide components (CaO, FeO, Fe 2O 3 and SiO 2) cannot describe the data set within experimental error. Instead, the inclusion of excess terms in CaFe 3+ and CaSi (product terms using the oxides) is required to yield a fit that describes the experimental data within error. The nonlinear compositional-dependence of the molar volumes of melts in this system can be explained by structural considerations of the roles of Ca and Fe 3+. The volume behavior of melts in this system is significantly different from that in the Na 2O-FeO-Fe 2O 3-SiO 2 system, consistent with the proposal that a proportion of Fe 3+ in melts in the CaO-FeO-Fe 2O 3-SiO 2 system is not tetrahedrally-coordinated by oxygen, which is supported by differences in 57Fe Mössbauer spectra of glasses. Specifically, this study confirms that the 57Fe Mössbauer spectra exhibit an area asymmetry and higher values of isomer shift of the ferric doublet that vary systematically with composition and temperature (this study; Dingwell and Virgo, 1987, 1988). These observations are consistent with a number of other lines of evidence ( e.g., homogeneous redox equilibria, Dickenson and Hess, 1986; viscosity, Dingwell and Virgo, 1987,1988). Two species of ferric iron, varying in proportions with temperature, composition and redox state, are sufficient to describe the above observations. The presence of more than one coordination geometry for Fe 3+ in low pressure silicate melts has several implications for igneous petrogenesis. The possible effects on compressibility, the pressure dependence of the redox ratio, and redox enthalpy are briefly noted.

Impact History on Vesta: Petrographic, Compositional and Future Chronological Studies of Melt Clasts in Howardites

NASA Technical Reports Server (NTRS)

Cartwright, J. A.; Mittlefehldt, D. W.; Hodges, K. V.; Wadhwa, M.

2015-01-01

Howardite meteorites are polymict breccias composed mainly of eucritic and diogenitic material that likely originate from the surface of the Asteroid 4 Vesta. They can be separated into two subtypes: Regolithic, which represent the lithified remains of the active vestan regolith; Fragmental, which represent simpler polymict breccias. Amongst the regolithic features observed in the former, melt clasts are particularly striking for their appearance and compositional variability. They range from glassy spherules to finely crystalline (i.e., devitrified) clasts, and clasts containing only relict mineral grains to those containing only phenocrysts. Glasses can be separated into compositional sub-types including those with low FeO/MgO ratios (less than 5) -low alkali glasses, K-rich (K2O greater than 0.2 wt.%), Na-rich (Na2O greater than 0.6 wt.%) and CaO-rich, and those with high FeO/MgO ratios (greater than 10). There is also a distinction to be made between primary volcanic melt clasts and those produced by impacts. While suggested that a lack of chemical homogeneity among their studied melt clasts ruled out a primary volcanic origin, the low siderophile element contents observed in such clasts suggest less compositional influence from impactors than commonly assumed. Studying the chronology of the impact melt clasts in howardites can help us to better determine the timing of impact events on Vesta and the asteroid belt. In this research, we are launching an investigation into the petrology, composition (major/trace element and noble gas) and chronology of melt clasts in howardites. We have selected a set of howardites known to contain large quantities of melt clasts, and have begun the petrological and compositional studies of these materials. Once the melt clasts have been fully classified, we aim to perform chronological studies of individual clasts using both the Ar-40/Ar-39 and Pb-Pb chronometers, as well as determine the noble gas components present. Of particular note, the study will take advantage of the laser ablation techniques associated with the noble gas facilities at ASU, which will allow high-resolution, in-situ analysis of individual clasts. The broader aim of this work is to ascertain whether the impact flux in the region of the asteroid belt was similar to that on the Moon. Our understanding of impact events in the inner Solar System relies heavily on our analyses of lunar meteorites and returned samples, and there is currently some debate regarding whether there was a "Lunar Cataclysm" event around approx. 3.9 Ga, or the end of an epoch of "Late Heavy Bombardment" (LHB) at this time. New and more comprehensive constraints on howardite melt clast ages may help determine whether the asteroid belt experienced such a cataclysm or LHB.

Determining pre-eruptive compositions of late Paleozoic magma from kaolinized volcanic ashes: Analysis of glass inclusions in quartz microphenocrysts from tonsteins

NASA Astrophysics Data System (ADS)

Webster, James D.; Congdon, Roger D.; Lyons, Paul C.

1995-02-01

Glass inclusions in quartz microphenocrysts were analyzed for major and minor elements by electron microprobe and H, Li, Be, B, Rb, Sr, Y, Nb, Mo, Sn, Cs, Ce, Th, and U by ion microprobe. The phenocrysts and inclusions occur as fresh relicts in about eleven strongly kaolinized, air-fall volcanic ash units (tonsteins) that outcrop in five states located in the central Appalachian basin; the ashes were erupted during the Pennsylvanian. Even though the whole-rock tonstein samples are extremely altered, the glass trapped in quartz microphenocrysts preserves pre-eruptive melt compositions, and, consequently, the inclusions are useful for determining compositions of source magmas and identifying geochemical trends indicative of magmatic evolution. Interpretation of inclusion compositions indicates the strongly altered tonsteins were derived from potassium-enriched, metaluminous to mildly peraluminous magma(s). The tonsteins can be divided into two groups on the basis of trapped melt compositions: older tonsteins that have inclusions with high Sr and normative quartz contents and comparatively low concentrations of U, Th, Rb, Y, Cs, Nb, F, and Cl (±Be) and younger tonsteins whose inclusions contain low Sr and normative quartz and high concentrations of U, Th, Rb, Y, Cs, Nb, F, and Cl (±Be). In general, as concentrations of Sr decreased, the magmatic abundances of Rb, Y, Cs, Nb, U, Th, Cl, and F (±Be) increased. The associated magma or magmas were highly evolved, volatile enriched, and contained Rb, Nb, and Y abundances characteristic of continental within-plate granites; compositions ranged from high-silica rhyolite to topaz rhyolite. Pre-eruptive volatile abundances in the source magma(s) were generally high but also highly variable. Chlorine contents of melt(s) ranged from 0.02-0.23 wt%, and F ranged from 0.01-0.7 wt%. Concentrations of H 2O in melt(s) ranged from 1.6-6.5 wt%. The high pre-eruptive H 2O contents are consistent with large eruptive volumes indicating the precursor rhyolites, which weathered to tonsteins, were a result of plinian eruptions. Even though pre-eruptive water concentrations exhibit no recognizable trends with any elements studied, magmatic evolution appears to have been a strong function of F and H 2O in melt(s); the thermal stabilities of quartz and feldspar were controlled by F and H 2O activities at pressures of approximately 0.5-1 kbar.

The role of the metasomatized oceanic lithosphere on the composition of mid-ocean ridge basalts from the East Pacific Rise

NASA Astrophysics Data System (ADS)

Shimizu, K.; Saal, A. E.

2016-12-01

In the present study, we evaluate the effect of melting of a metasomatized oceanic lithosphere on the chemical composition of MORB using the East Pacific Rise (EPR) mid-ocean ridge basalts (MORB) from the Quebrada-Discovery-GoFar (QDG) transform fault system, Northern EPR seamounts, and Macquarie Island [1-3]. EMORB from the QDG have trace element and volatile-refractory element ratios different from those measured in NEPR seamounts and Macquarie EMORB. The unique chemical composition of the QDG EMORB might indicate contribution from the oceanic lithosphere during the formation of intra-transform spreading centers due to clockwise rotation in Pacific-Nazca plate relative motion. In addition, the compositions of some of the Petit-spot lavas recently erupted along lithospheric fractures in the Pacific Plate in response to its flexure near the Japan Trench [4] have geochemical signatures that might suggest melts derived from a metasomatized oceanic mantle lithosphere. We evaluate this hypothesis using a geochemical model assuming a two-component asthenospheric mantle (DDMM and EDMM) and formation of hydrous cumulates in the oceanic mantle lithosphere by crystallization of low degree melts of the EDMM [3, 5]. The model suggests that melting of the hydrous cumulates can reproduce the composition of EMORB from QDG transform fault and some of the Petit-spot lavas. The process of melting the metasomatized oceanic lithosphere may significantly affect the chemical composition of MORB, and the common assumption for the purely asthenosphere origin of MORB could lead to inaccurate estimates of the Earth's upper mantle composition. We also show that similar process might affect not only oceanic, but also off-craton sub continental mantle lithosphere. References: [1] Niu et al., 2002 EPSL 199. [2] Kamenetsky et al., 2002 J Petrol 43. [3] Shimizu et al., 2016 GCA 176. [4] Hirano et al., 2006 Science 313. [5] Pilet et al., 2011 J Petrol 52.

Producing Martian Lithologies with Geophysically-Constrained Martian Mantle Compositions

NASA Astrophysics Data System (ADS)

Minitti, M. E.; Fei, Y.; Bertka, C. M.

2008-12-01

The Martian meteorites, rocks measured by the Mars Exploration Rovers (MER) and lithologies detected by orbital assets represent a diversity of igneous rocks that collectively provide insight into the formation and evolution of Mars. Experimental studies aimed at reproducing the observed igneous lithologies have met with varying degrees of success [e.g., 1,2,3], No study has yet been able to reproduce both Martian meteorite parent magmas and the basalts measured by MER at Gusev Crater [e.g., 1,3]. We attempted a different approach to successfully reproducing Martian igneous lithologies by using geophysical constraints on Martian bulk Fe (wt.%), Fe/Si and mantle Mg# [4,5] to identify mixtures of chondrite compositions that formed plausible Martian mantle compositions. We identified two candidate chondrite mixtures for Mars, CM+L and H+L. We synthesized the CM+L and H+L compositions from oxide, carbonate and phosphate powders and fixed them at an oxygen fugacity below the magnetite-wüstite buffer (MW-1). We conducted experiments at 2 GPa (corresponding to ~150 km in the Martian mantle) between 1300-1600 °C for 4-48 hours in the end-loaded piston cylinder apparatus at the Geophysical Laboratory. Thusfar, we have also conducted experiments at 4 GPa (corresponding to ~320 km in the Martian mantle) between 1425-1475 °C for 210-240 minutes in a Walker-type multi-anvil apparatus at the Geophysical Laboratory. We utilized an 18/11 (octahedron edge length/truncated edge length, in mm) assembly. In both assembly types, the sample was contained within a graphite capsule welded into a Pt tube. We analyzed the experiment products in electron probes at either the Geophysical Laboratory or Arizona State University. Fe and Mg contents of olivine, orthopyroxene and melt were used to assess the attainment of equilibrium for each run product. No significant difference exists between the CM+L and H+L experiment products. The near-solidus phase assemblage of the 2-GPa experiments is ol+opx+cpx. Melts at 2 GPa have MgO, FeO, and Mg# values that either overlap those of Martian meteorite parent melts or are capable of reproducing Martian meteorite parent melt compositions through low-pressure olivine fractionation. The 2- GPa melts do not, however, have CaO/Al2O3 values that intersect those of the Martian meteorite parent magmas. This finding mirrors the inability of previous studies [e.g., 1] to form the Martian meteorites. However, the 2-GPa products can lead to Gusev-like basalts via a two-step process. 20-25% melting yields basalt compositions from which subsequent low pressure olivine fractionation leads to basalts with MgO, FeO, CaO and Al2O3 contents and Mg# and CaO/Al2O3 values like those of the Gusev basalts. The near-solidus phase assemblage of the 4-GPa experiments is ol+opx+cpx+garnet. The melt composition resulting from ~20% melting of the CM+L mantle composition has MgO, FeO, CaO and Al2O3 contents and Mg# and CaO/Al2O3 values that fall among Martian meteorite parent magma compositions. Thus, the geophysically-constrained mantle compositions are capable of producing melts with Gusev and Martian meteorite parent magma affinities by simply shifting the pressure of melting. [1] Bertka C.M. and Holloway J.R. (1994) CMP 115, 313-322. [2] Agee C.B. and Draper D.S. (2005) LPSC XXXVI, #1434. [3] Monders A. et al. (2007) MaPS, 42, 131-148. [4] Bertka C.M. and Fei Y. (1998) Science, 281, 1838-1840. [5] Bertka C.M. and Fei Y. (1998) EPSL, 157:79-88.

Hydrogen Isotopic Systematics of Nominally Anhydrous Phases in Martian Meteorites

NASA Astrophysics Data System (ADS)

Tucker, Kera

Hydrogen isotope compositions of the martian atmosphere and crustal materials can provide unique insights into the hydrological and geological evolution of Mars. While the present-day deuterium-to-hydrogen ratio (D/H) of the Mars atmosphere is well constrained (~6 times that of terrestrial ocean water), that of its deep silicate interior (specifically, the mantle) is less so. In fact, the hydrogen isotope composition of the primordial martian mantle is of great interest since it has implications for the origin and abundance of water on that planet. Martian meteorites could provide key constraints in this regard, since they crystallized from melts originating from the martian mantle and contain phases that potentially record the evolution of the H 2O content and isotopic composition of the interior of the planet over time. Examined here are the hydrogen isotopic compositions of Nominally Anhydrous Phases (NAPs) in eight martian meteorites (five shergottites and three nakhlites) using Secondary Ion Mass Spectrometry (SIMS). This study presents a total of 113 individual analyses of H2O contents and hydrogen isotopic compositions of NAPs in the shergottites Zagami, Los Angeles, QUE 94201, SaU 005, and Tissint, and the nakhlites Nakhla, Lafayette, and Yamato 000593. The hydrogen isotopic variation between and within meteorites may be due to one or more processes including: interaction with the martian atmosphere, magmatic degassing, subsolidus alteration (including shock), and/or terrestrial contamination. Taking into consideration the effects of these processes, the hydrogen isotope composition of the martian mantle may be similar to that of the Earth. Additionally, this study calculated upper limits on the H2O contents of the shergottite and nakhlite parent melts based on the measured minimum H2O abundances in their maskelynites and pyroxenes, respectively. These calculations, along with some petrogenetic assumptions based on previous studies, were subsequently used to infer the H2O contents of the mantle source reservoirs of the depleted shergottites (200-700 ppm) and the nakhlites (10-100 ppm). This suggests that mantle source of the nakhlites is systematically drier than that of the depleted shergottites, and the upper mantle of Mars may have preserved significant heterogeneity in its H2O content. Additionally, this range of H2O contents is not dissimilar to the range observed for the Earth's upper mantle.

Silsesquioxanes as precursors to ceramic composites

NASA Technical Reports Server (NTRS)

Hurwitz, Frances I.; Hyatt, Lizbeth H.; Gorecki, Joy; Damore, Lisa

1987-01-01

Silsesquioxanes having the general structure RSiO sub 1.5, where R = methyl, propyl, or phenyl, melt flow at 70 to 100 C. Above 100 C, free -OH groups condense. At 225 C further crosslinking occurs, and the materials form thermosets. Pyrolysis, with accompanying loss of volatiles, takes place at nominally 525 C. At higher temperatures, the R group serves as an internal carbon soruce for carbo-thermal reduction to SiC accompanied by the evolution of CO. By blending silsesquioxanes with varying R groups, both the melt rheology and composition of the fired ceramic can be controlled. Fibers can be spun from the melt which are stable in argon in 1400 C. The silsesquioxanes also were used as matrix precursors for Nicalon and alpha-SiC platelet reinforced composites.

The Growth and Characterization of the Bismuth Strontium-Calcium 2212 Superconductor

NASA Astrophysics Data System (ADS)

Moulton, Linda Vidale

A miniaturized float zone technique, sometimes referred to as the Laser-heated Pedestal Growth (LHPG) method, was used to produce high quality crystals of the incongruently melting rm Bi_2Sr_2CaCu _2O_{8+delta} (2212) superconductor. The main focus of this research was to (1) produce superconducting samples having different compositions, (2) identify the melt compositions and growth temperatures which produced these samples, and (3) determine the variation of their superconducting transition temperature (T _{rm C}) with composition and processing conditions. The rm Bi_2(Sr,Ca) _3Cu_2O_{8+delta} crystallization experiments were supplemented by a series of similar experiments on the incongruently melting compound rm Ca_3Al_2O_6. The phase equilibria in the CaO-rm Al_2O _3 system has been thoroughly studied, and by analyzing the float-zone growth of this simpler and better-characterized material, it was verified that phase equilibria information and solidification behavior could be extracted from and explained by these solidification experiments. Two different types of nonplanar, crystal/melt interface morphologies were observed in the rm Ca_3Al_2O_6 experiments. Each reflected the influence of the phase equilibria in the CaO-rm Al_2O_3 system and component segregation in the melt. The molten zone compositions were found to approach those predicted by the CaO-rm Al_2O_3 phase diagram as the growth rate decreased, in accordance with the Burton-Prim Slichter relationship. Excellent agreement was obtained between actual phases found to coexist at the rm Ca_3Al_2O_6 /melt interface and the predictions of classical crystal growth theory. Based on the results of the rm Ca _3Al_2O_6 crystallization study, the crystal/melt equilibria in the far more complex rm Bi_2O_3-SrO-CaO-CuO system was evaluated by determining the phases formed during the superconductor growth experiments. The melt compositions were found to be rm Bi_2O_3 -rich and SrO-poor relative to the compositions of the 2212 crystals grown from them. The CaO and CuO segregation coefficients, on the other hand, were observed to be near unity. As one would expect for an incongruently -melting compound, segregation at the solidification front generally decreased with increasing crystallization temperature, but all the segregation coefficients were not observed to simultaneously approach unity. The superconducting transition temperatures (T _{rm C}'s) of six as-crystallized samples having homogeneous crystal compositions were also measured. Sample T_{rm C} was observed to increase with increasing growth temperature and, therefore, change with crystal composition. The results of this study suggested that it is desirable to grow crystals at the highest possible crystallization temperature since they will: (1) have the highest as-grown T_{rm C} 's, and (2) solidify with the least component segregation at the growth interface. In addition, the analysis presented here suggests that such growth is not recommended at higher growth rates, since crystals with mid-range solidus compositions (and consequently, moderate growth temperatures) should crystallize most reliably as single-phase samples at higher growth rates.

New Insights From Whole Rock and Mineral Data on the Magmatic and Tectonic Evolution of the Columbia River Basalt Group (USA)

NASA Astrophysics Data System (ADS)

Caprarelli, G.; Reidel, S. P.

2004-12-01

The Miocene Columbia River Basalt Group (CRBG) of north-western USA was emplaced in a geologically dynamic setting characterized by a close association between magmatism and lithospheric thinning and rifting. We present and discuss electron probe microanalysis and XRFA data obtained from samples spanning the entire sequence of the CRBG. The examined basalts have near-aphyric textures. No glass is present, and plagioclase and augitic clinopyroxene are dominant matrix and groundmass phases. Plagioclase microcrysts are labradoritic to bytownitic. Whole rock compositions were taken as proxies of the liquid compositions. Application of plagioclase / melt and clinopyroxene / melt geothermobarometers indicated that during crustal ascent the magmas were dry, and that pre-eruptive pressures and temperatures ranged from 0 to 0.66 GPa and 1393 to 1495 K, respectively. In a P-T diagram most of the samples are distributed along a general CRBG trend, while some samples plot along a parallel higher temperature trend. The calculated P-T values, the positive correlation between calculated P and T, and no horizontal alignment of the data, exclude the presence of upper crustal solidification fronts, and indicate that magma aggregation zones were located deeper than 25 km, plausibly immediately below the Moho, that in this region is at a depth of approximately 35 km. Episodic stretching of the lithosphere best explains the observed parallel P-T trends. Whole rock major element abundances resulted from fractional crystallization of the magmas during ascent. To retrieve the compositions of the primitive melts we added to the bulk rock compositions variable amounts of magnesian olivine [Mg/(Mg+Fe) = 0.88], and derived the evolution of olivine fractionating magmas in equilibrium with mantle harzburgite. Two groups of samples were found, corresponding to the parallel P-T trends obtained from mineral / melt calculations. The highest temperature trend corresponds to samples whose calculated primitive compositions are in agreement with those obtained from peridotite melting experiments (as published in the relevant literature). Interpretation of results for rocks belonging to the general CRBG trend suggests, either: (a) that higher forsteritic content olivine should be used in the calculations; or, (b) that melt / ol / opx reactions occurred. Investigation of the CRBG primitive compositions has relevance with regard to the geodynamic evolution models of this region. We are currently undertaking melt inclusion studies of suitable CRBG samples.

Earth's Various Recipes for Making Lherzolites

NASA Astrophysics Data System (ADS)

Becker, H.; van Acken, D.

2007-12-01

Petrological and cosmochemical arguments suggest that the convecting upper mantle overall should have a lherzolitic composition, otherwise, continous production of MORB would not be feasible. The predominance of harzburgites among ocean floor peridotites fits this picture because harzburgites are commonly believed to be the residue of high degrees of partial melting at shallow depths, with fertile components lost during polybaric partial melting. Implicitly, it is commonly assumed that the deeper parts of the asthenosphere and new-formed lithosphere should be residues of low-degree partial melting. This view has been supported by the abundance of lherzolites among mantle xenoliths and orogenic peridotite massifs. But is this model really correct? Data and observations on oceanic and continental peridotites accumulated over recent years hint that reality is more complicated. On the basis of mineral and whole rock compositions, and isotopic data, it has long been suspected that many continental peridotites have undergone some form of pyroxene addition via percolating melts, yet the efficacy of these processes has been uncertain. Novel combination of structural and chemical work by Le Roux et al. (2007) indicates that melt influx may have converted deformed harzburgitic rocks of the Lherz peridotite massif into little-deformed spinel lherzolites. Refertilization by MORB-like sub-lithospheric melts, and marble cake style stretching of pyroxenites have been implicated as major processes that affected the composition of peridotites from the Totalp spinel lherzolite body, a fragment of Jurassic ultra-slow spreading Thetys ocean floor in the Swiss Alps (van Acken et al., 2007). Refertilization by melts has been associated with lherzolites from oceanic fracture zones (e. g., Seyler and Bonatti, 1997) and may be responsible for lherzolites alternating with harzburgitic domains at the Arctic Gakkel ridge (Liu et al. 2007). Evidence for compositional transformation of depleted peridotites into fertile rocks, both in young oceanic and in continental settings brings up questions that need to be addressed in the future: How common are truly residual lherzolites? Are lherzolites suitable to constrain the composition of the primitive mantle? How are fertile components in the asthenosphere distributed? Mantle rocks may have more surprises in stock.

The Origin of Silicic Arc Crust - Insights from the Northern Pacific Volcanic Arcs through Space and Time

NASA Astrophysics Data System (ADS)

Straub, S. M.; Kelemen, P. B.

2016-12-01

The remarkable compositional similarities of andesitic crust at modern convergent margins and the continental crust has long evoked the hypothesis of similar origins. Key to understanding either genesis is understanding the mode of silica enrichment. Silicic crust cannot be directly extracted from the upper mantle. Hence, in modern arcs, numerous studies - observant of the pervasive and irrefutable evidence of melt mixing - proposed that arc andesites formed by mixing of mantle-derived basaltic melts and fusible silicic material from the overlying crust. Mass balance requires the amount of silicic crust in such hybrid andesites to be on the order to tens of percent, implying that their composition to be perceptibly influenced by the various crustal basements. In order to test this hypothesis, major and trace element compositions of mafic and silicic arc magmas with arc-typical low Ce/Pb< 10 of Northern Pacific arcs (Marianas through Mexico) were combined with Pb isotope ratios. Pb isotope ratios are considered highly sensitive to crustal contamination, and hence should reflect the variable composition of the oceanic and continental basement on which these arcs are constructed. In particular, in thick-crust continental arcs where the basement is isotopically different from the mantle and crustal assimilation thought to be most prevalent, silicic magmas must be expected to be distinct from those of the associated mafic melts. However, in a given arc, the Pb isotope ratios are constant with increasing melt silica regardless of the nature of the basement. This observation argues against a melt origin of silicic melts from the crustal basement and suggest them to be controlled by the same slab flux as their co-eval mafic counterparts. This inference is validated by the spatial and temporal pattern of arc Pb isotope ratios along the Northern Pacific margins and throughout the 50 million years of Cenozoic evolution of the Izu Bonin Mariana arc/trench system that are can be related to with systematic, `real-time' changes in the composition of the slab flux with no role of the crustal basement. In summary, these data suggest that that silicic melts are ultimately genetically linked to the mafic co-eval series from the mantle, by such mechanisms as fractional crystallization, or melt-rock reactions, or a combination of both.

Geochemical Character of the Aono Volcanic Group in SW Japan Arc: Implications for Genetic Relationship between Slab Melting and EM Isotopic Signature

NASA Astrophysics Data System (ADS)

Shimoda, G.; Shinjoe, H.; Kogiso, T.; Ishizuka, O.; Yamashita, K.; Yoshitake, M.; Itoh, J.; Ogasawara, M.

2016-12-01

The SW Japan arc is characterized by active subduction of a relatively young (15-26 Ma) segment of the Philippine Sea plate, Shikoku basin, beneath the Eurasian plate and is known for the occurrence of adakites on the quaternary volcanic front. As adakite is typically generated in subduction zones, where high geothermal gradients can be attained in the slab, the adakite magmas are considered to be produced by slab melting. From this perspective, adakites are considered to be modern geochemical analogues of the tonalite-trondhjemite-granodiorite (TTG) suite that can be a major constituent of early continental crust. It has been inferred that recycling of continental crustal material back into the mantle could be a possible origin of enriched mantle reservoirs, such as EM1 and EM2. In order to reveal the role of slab melting on the production of EM isotopic signature, we have conducted a detailed major/trace element and Pb-Nd-Sr isotopic study of 17 adakites from Aono volcanic group in the western end of Honshu Island. The isotopic compositions of the Aono volcanic rocks clearly form a mixing line between the Shikoku back arc basin basalts and local sediments from the Nankai Trough. In addition, the isotopic compositions of Aono adakites have depleted isotopic composition showing some overlap with subducted Shikoku basin basalts. This may imply that the chemical composition of Aono adakites could be mainly derived from Shikoku basin basalts as pointed out by recent work (Kimura et al., 2014). Accordingly, the effect of crustal contamination or sediment melting could be relatively small. On the basis of this assumption, the chemical composition of Aono adakites are used to estimate the chemical fractionation during slab melting. In this presentation, we will present new results of isotopic and trace element analyses of adakites from Aono volcanic group in the SW Japan and discuss role of slab melting in the production of EM reservoirs.

Melting relations of model lherzolite in the system CaO-MgO-Al2O3-SiO2 at 2.4-3.4 GPa and the generation of komatiites

NASA Astrophysics Data System (ADS)

Gudfinnsson, Gudmundur H.; Presnall, Dean C.

1996-12-01

Isobarically invariant phase relations in the CaO-MgO-Al2O3-SiO2 system (CMAS) involving the lherzolite phase assemblage in equilibrium with liquid have been determined at 2.4-3.4 GPa. These phase relations form the solidus of model lherzolite in the CMAS system. Our data, which include determinations of all phase compositions, are in excellent agreement with the 3.0 and 4.0 GPa points of Milholland and Presnall [1991] and Davis and Schairer [1965], respectively. The invariant transition on the P-T solidus curve from spinel- to garnet-lherzolite at 3.0 GPa, 1575°C [Milholland and Presnall, 1991], is confirmed, but we observe that the theoretically required temperature depression on the solidus curve at this point is not experimentally detectable. Composition trends along the solidus take a sharp turn at the transition. In the spinel-lherzolite stability field, melt compositions become increasingly Fo-normative and less En-normative with increasing pressure, but become less Fo-normative and more pyroxenitic as pressure increases in the garnet-lherzolite stability field. Calculated melting reactions indicate that forsterite is in reaction relationship with the melt up to 3.0 GPa. Orthopyroxene is also in reaction relationship at pressures higher than just over 2.8 GPa and is the only phase in reaction relationship with the melt in the garnet-lherzolite stability field. Comparison of the normative compositions and the CaO/Al2O3 values of the komatiites of Gorgona Island and of the Reliance Formation in Zimbabwe with the compositions of liquids along the solidus of model lherzolite in the CMAS system indicates that the former komatiites were generated at pressures close to 3.7 GPa and the latter at close to 4.5 GPa, assuming that the melt generation occurred in the presence of the complete garnet-lherzolite assemblage.

Hf-Nd isotope decoupling in the oceanic lithosphere: constraints from spinel peridotites from Oahu, Hawaii

NASA Astrophysics Data System (ADS)

Bizimis, Michael; Sen, Gautam; Salters, Vincent J. M.

2004-01-01

We present a detailed geochemical investigation on the Hf, Nd and Sr isotope compositions and trace and major element contents of clinopyroxene mineral separates from spinel lherzolite xenoliths from the island of Oahu, Hawaii. These peridotites are believed to represent the depleted oceanic lithosphere beneath Oahu, which is a residue of a MORB-related melting event some 80-100 Ma ago at a mid-ocean ridge. Clinopyroxenes from peridotites from the Salt Lake Crater (SLC) show a large range of Hf isotopic compositions, from ɛHf=12.2 (similar to the Honolulu volcanics series) to extremely radiogenic, ɛHf=65, at nearly constant 143Nd/ 144Nd ratios ( ɛNd=7-8). None of these samples show any isotopic evidence for interaction with Koolau-type melts. A single xenolith from the Pali vent is the only sample with Hf and Nd isotopic compositions that falls within the MORB field. The Hf isotopes correlate positively with the degree of depletion in the clinopyroxene (e.g. increasing Mg#, Cr#, decreasing Ti and heavy REE contents), but also with increasing Zr and Hf depletions relative to the adjacent REE in a compatibility diagram. The Lu/Hf isotope systematics of the SLC clinopyroxenes define apparent ages of 500 Ma or older and these compositions cannot be explained by mixing between any type of Hawaiian melts and the depleted Pacific lithosphere. Metasomatism of an ancient (e.g. 1 Ga or older) depleted peridotite protolith can, in principle, explain these apparent ages and the Nd-Hf isotope decoupling, but requires that the most depleted samples were subject to the least amount of metasomatism. Alternatively, the combined isotope, trace and major element compositions of these clinopyroxenes are best described by metasomatism of the 80-100 Ma depleted oceanic lithosphere by melts products of extensive mantle-melt interaction between Honolulu Volcanics-type melts and the depleted lithosphere.

An electrochemical series of redox couples in silicate melts - A review and applications to geochemistry

NASA Technical Reports Server (NTRS)

Schreiber, Henry D.

1987-01-01

An electrochemical series for redox couples in a glass-forming oxide melt is developed. This series is a quantitative numerical scale of reference reduction potentials of the redox couples in a silicate melt that is a model for basaltic magmas. The redox couples are ordered in terms of their reference reduction potentials; the order appears to be relatively independent of the exact melt composition and temperature. Thus, upon calibration to a desired composition, oxygen fugacity, and temperature, this electrochemical series can provide estimates of redox state proportions in basaltic magmas on different planetary bodies. The geochemical electrochemical series can also be used to understand the interrelationship of the redox state of the magma and the presence of volatile species such as oxygen, water, sulfur gases, and carbon gases.

Properties of sugar-based low-melting mixtures

NASA Astrophysics Data System (ADS)

Fischer, Veronika; Kunz, Werner

2014-05-01

Physico-chemical properties of ternary sugar-based low-melting mixtures were determined. Choline chloride, urea and glucose or sorbitol, serving as sugars, were blended in various compositions. The refractive index, density, viscosity, decomposition temperatures and glass transition temperatures were measured. Further, the influence of temperature and water content was investigated. The results show that the mixtures are liquid below room temperature and the viscosity and density are dependent on the temperature and composition. Moreover, the viscosity decreases with increasing water content. These mixtures are biodegradable, low toxic, non-volatile, non-reactive with water and can be accomplished with low-cost materials. In consideration of these advantages and a melting point below room temperature, these low-melting mixtures can be a good alternative to ionic liquids as well as environmentally unfriendly and toxic solvents.

Melt-infiltrated Sic Composites for Gas Turbine Engine Applications

NASA Technical Reports Server (NTRS)

Morscher, Gregory N.; Pujar, Vijay V.

2004-01-01

SiC-SiC ceramic matrix composites (CMCs) manufactured by the slurry -cast melt-infiltration (MI) process are leading candidates for many hot-section turbine engine components. A collaborative program between Goodrich Corporation and NASA-Glenn Research Center is aimed at determining and optimizing woven SiC/SiC CMC performance and reliability. A variety of composites with different fiber types, interphases and matrix compositions have been fabricated and evaluated. Particular focus of this program is on the development of interphase systems that will result in improved intermediate temperature stressed-oxidation properties of this composite system. The effect of the different composite variations on composite properties is discussed and, where appropriate, comparisons made to properties that have been generated under NASA's Ultra Efficient Engine Technology (UEET) Program.

Preparation and crystalline studies of PVDF hybrid composites

NASA Astrophysics Data System (ADS)

Chethan P., B.; Renukappa, N. M.; Sanjeev, Ganesh

2018-04-01

The conducting polymer composites have become increasingly important for electrical and electronic applications due to their flexibility, easy of processing, high strength and low cost. A flexible conducting polymer hybrid composite was prepared by melt mixing of nickel coated multi-walled carbon nanotubes (Ni-MWNT) and graphitized carbon nanofibres (GCNF) in Polyvinylidene fluoride (PVDF) matrix. The crystalline structures of the nano composites were studied by X-ray diffraction (XRD) method and showed characteristic peaks at 17.7°, 18.5°, 20° and 26.7° of 2θ. The β phase crystalline nature of the composite films, degree of crystallinity, melting temperature and crystallization behavior of the hybrid composites were studied using appropriate characterization techniques. The filler in the insulating polymer matrix plays crucial role to improve the crystallinity of the composites.

Evaluation of the Lithospheric Contribution to Southern Rio Grande Rift Mafic Melts

NASA Astrophysics Data System (ADS)

Konter, J. G.; Crocker, L.; Anaya, L. M.; Rooney, T. O.

2011-12-01

As continental rifting proceeds, the accommodation of lithospheric thinning by mechanical extension and magmatic intrusion represents an important but poorly constrained tectonic process. Insight into role of the magmatic component may come from the composition of volcanic products, which can record magma-lithosphere interactions. The volcanic activity in continental rift environments is frequently characterized by bimodal associations of mafic and silicic volcanism with heterogenous lithospheric contributions. We present a new integrated data set from several mafic volcanic fields in the Rio Grande Rift, consisting of major and trace element compositions, as well as isotopes. This data set provides insight into asthenospheric melting processes and interactions with the overlying lithosphere. The melting processes and the related extensional volcanism is the result of foundering of the Farallon slab. Large volume silicic eruptions such as those in the Sierra Madre Occidental originate from a large contribution of lithospheric melting, with a subordinate asthenospheric contribution. In contrast, Late Tertiary and Quaternary basaltic volcanic fields in the Rio Grande Rift were likely sourced in the asthenosphere and did not reside in the lithosphere for substantial periods. As a result the region is the ideal natural laboratory to investigate the interaction of asthenospheric melts with the lithosphere. In particular the wide array of volcanic fields contain multiple xenolith localities, such as Kilbourne Hole, providing direct samples of lithosphere and crust. Although previous studies have focused on correlations between amount of extension related to Farallon slab foundering, volcanic compositions, and their mantle sources, we present data that suggest that some compositional signatures may pre-date current tectonic processes. Radiogenic isotope data from several volcanic fields in New Mexico show a converging pattern in Pb isotope compositions, focusing on the unradiogenic Pb isotope composition of lower crustal xenoliths from Kilbourne Hole. The opposite ends of the converging trends are more radiogenic for some volcanic fields than the (lithospheric) mantle xenoliths of the Potrillo, San Carlos and Geranimo volcanic fields. Combined Pb-Sr isotope compositions for these fields are consistent with a trend from lower crustal xenoliths to mantle xenoliths, but show more variability. This variability may be explained by a small upper crustal contribution, in agreement with the Pb isotope systematics. Therefore, a common unradiogenic lower crustal composition likely contributed to the asthenospheric melts, followed by upper crustal contamination. The unradiogenic character of the lower crust implies an ancient event created the required low U/Pb ratios that generated the present-day Pb isotope compositions.

Melting of Fe-Si-O alloys: the Fate of Coexisting Si and O in the Core

NASA Astrophysics Data System (ADS)

Arveson, S. M.; Lee, K. K. M.

2017-12-01

The light element budget of Earth's core plays an integral role in sustaining outer core convection, which powers the geodynamo. Many experiments have been performed on binary iron compounds, but the results do not robustly agree with seismological observations and geochemical constraints. Earth's core is almost certainly made up of multiple light elements, so the future of core composition studies lies in ternary (or higher order) systems in order to examine interactions between light elements. We perform melting experiments on Fe-Si-O alloys in a laser-heated diamond-anvil cell to 80 GPa and 4000 K. Using 2D multi- wavelength imaging radiometry together with textural and chemical analysis of quenched samples, we measure the high-pressure melting curves and determine partitioning of light elements between the melt and the coexisting solid. Quenched samples are analyzed both in map view and in cross section using scanning electron microscopy (SEM) and electron microprobe analysis (EPMA) to examine the 3D melt structure and composition. Partitioning of light elements between molten and solid alloys dictates (1) the density contrast at the ICB, which drives compositional convection in the outer core and (2) the temperature of the CMB, an integral parameter for understanding the deep Earth. Our experiments suggest silicon and oxygen do not simply coexist in the melt and instead show complex solubility based on temperature. Additionally, we do not find evidence of crystallization of SiO2 at low oxygen content as was recently reported.11 Hirose, K., et al., Crystallization of silicon dioxide and compositional evolution of the Earth's core. Nature, 2017. 543(7643): p. 99-102.

Microstructure and Mechanical Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration of Zr2Cu into Porous Preforms from Partially Carburized W Powders

NASA Astrophysics Data System (ADS)

Wang, Dong; Wang, Yu-Jin; Huo, Si-Jia; Zhao, Yan-Wei; Ouyang, Jia-Hu; Song, Gui-Ming; Zhou, Yu

2018-03-01

W-ZrC composites with different W contents from 48 to 73 vol.% have been synthesized by reactive melt infiltration of Zr2Cu melt into porous preforms from partially carburized W powders at 1300 °C for 1 h in vacuum. The influences of carbon content and porosity in the preforms on microstructure and mechanical properties of W-ZrC composites are investigated. Cold isostatic pressing followed by pre-sintering process is used to produce porous preforms with suitable porosities of 53.6-47% under a pressure of 100 MPa to allow sufficient penetration of Zr2Cu melt into the preforms. Small amounts of Cu-rich phases form in the synthesized W-ZrC composites after a complete reaction of y/2xZr2Cu(l) + WC y (s) = y/xZrC x (s) + W(s) + y/2xCu(l). These Cu-rich phases are distributed not only at the phase boundaries of W matrix and ZrC grains, but also in the interior of ZrC x grains. With decreasing W content from 73 to 48 vol.% in the W-ZrC composites, the flexural strength and fracture toughness increase from 519 to 657 MPa and from 9.1 to 10.6 MPa m1/2, respectively.

How unique is the Udachnaya-East kimberlite? Comparison with kimberlites from the Slave Craton (Canada) and SW Greenland

NASA Astrophysics Data System (ADS)

Kamenetsky, Vadim S.; Kamenetsky, Maya B.; Weiss, Yakov; Navon, Oded; Nielsen, Troels F. D.; Mernagh, Terrence P.

2009-11-01

The origin of alkali carbonates and chlorides in the groundmass of unaltered Udachnaya-East kimberlites in Siberia is still controversial. Contrary to existing dogma that the Udachnaya-East kimberlite was either contaminated by the crustal sediments or platform brines, magmatic origin of the groundmass assemblage has been proposed on the basis of melt immiscibility textures, melt inclusion studies, and strontium and neon isotope compositions. We further tested the idea of alkali- and chlorine enrichment of the kimberlite parental melt by studying olivine-hosted melt inclusions and secondary serpentine in kimberlites from the Slave Craton, Canada (Gahcho Kué, Jericho, Aaron and Leslie pipes) and southern West Greenland (Majuagaa dyke). Host olivine phenocrysts closely resemble groundmass olivine from the Udachnaya-East kimberlite in morphology, compositions (high-Fo, low-Ca), complex zoning with cores of varying shapes and compositions and rims of constant Fo. Melt inclusions in olivine consist of several translucent and opaque daughter phases and vapour bubble(s). The daughter crystals studied in unexposed inclusions by laser Raman spectroscopy and in carefully exposed inclusions by WDS-EDS are represented by Na-K chlorides, calcite, dolomite, magnesite, Ca-Na, Ca-Na-K and Ca-Mg-Ba carbonates, bradleyite Na 3 Mg(CO 3)(PO 4), K-bearing nahpoite Na 2(HPO 4), apatite, phlogopite and tetraferriphlogopite, unidentified sulphates, Fe sulphides, djerfisherite, pyrochlore (Na,Ca) 2Nb 2O 6(OH,F), monticellite, Cr-spinel and Fe-Ti oxides. High abundances of Na, K (e.g., (Na + K)/Ca = 0.15-0.85) and incompatible trace elements in the melt inclusions are confirmed by LA-ICPMS analysis of individual inclusions. Heating experiments show that melting of daughter minerals starts and completes at low temperatures (~ 100 °C and 600 °C, respectively), further reinforcing the similarity with the Udachnaya-East kimberlite. Serpentine minerals replacing olivine in some of the studied kimberlites demonstrate elevated abundances of chlorine (up to 3-4 wt.%), especially in the early generation. Despite heterogeneous distribution of chlorine such abundances are significantly higher than in the serpentine in abyssal and ophiolitic peridotites (< 0.5 wt.%). The groundmass of most kimberlites, including those studied here and altered kimberlites from the Udachnaya pipe, contain no alkali carbonates and chlorides and have low Na 2O (< 0.2 wt.%). We believe that alteration disturbs original melt compositions, with the alkaline elements and chlorine being mostly affected. However, the compositions of melt inclusions and serpentine are indicative of the chemical signature of a parental kimberlite melt. It appears that enrichment in alkalies and chlorine, as seen in unaltered Udachnaya-East kimberlites, is shared by other kimberlites, and thus can be assigned to deep mantle origin.

High Temperature Mechanical Behavior of MgAl2O4-YAG Eutectic Ceramic In Situ Composites by Float Zone Method

NASA Astrophysics Data System (ADS)

Abalı, Serkan

2017-09-01

The directionally solidified eutectic MgAl2O4-Y3Al5O12 crystal was prepared at a pressure of 0.4 MPa of ambient nitrogen gas by the high frequency induction heated floating zone furnace. In order to determine the high temperature characteristics, directionally solidified MgAl2O4-Y3Al5O12 eutectic phase has been analyzed with creep test, tensile strength, young modulus and fracture toughness at the various temperatures and the microstructural variations have been studied according to the analysis results. It has been seen that directionally solidified with zone melting MgAl2O4-YAG eutectic ceramic which has given the value of 168 MPa below 10-6/s strain rate at 1,700 °C temperature has revealed minimum stress.

Rhenium-osmium-isotope constraints on the age of iron meteorites

NASA Technical Reports Server (NTRS)

Horan, M. F.; Morgan, J. W.; Walker, R. J.; Grossman, J. N.

1992-01-01

Rhenium and osmium concentrations and the osmium isotopic compositions of iron meteorites were determined by negative thermal ionization mass spectrometry. Data for the IIA iron meteorites define an isochron with an uncertainty of approximately +/-31 million years for meteorites about 4500 million years old. Although an absolute rhenium-osmium closure age for this iron group cannot be as precisely constrained because of uncertainty in the decay constant of Re-187, an age of 4460 million years ago is the minimum permitted by combined uncertainties. These age constraints imply that the parent body of the IIAB magmatic irons melted and subsequently cooled within 100 million years after the formation of the oldest portions of chondrites. Other iron meteorites plot above the IIA isochron, indicating that the planetary bodies represented by these iron groups may have cooled significantly later than the parent body of the IIA irons.

Rhenium-osmium isotope constraints on the age of iron meteorites

USGS Publications Warehouse

Horan, M.F.; Morgan, J.W.; Walker, R.J.; Grossman, J.N.

1992-01-01

Rhenium and osmium concentrations and the osmium isotopic compositions of iron meteorites were determined by negative thermal ionization mass spectrometry. Data for the IIA iron meteorites define an isochron with an uncertainty of approximately ??31 million years for meteorites ???4500 million years old. Although an absolute rhenium-osmium closure age for this iron group cannot be as precisely constrained because of uncertainty in the decay constant of 187Re, an age of 4460 million years ago is the minimum permitted by combined uncertainties. These age constraints imply that the parent body of the IIAB magmatic irons melted and subsequently cooled within 100 million years after the formation of the oldest portions of chondrites. Other iron meteorites plot above the IIA isochron, indicating that the planetary bodies represented by these iron groups may have cooled significantly later than the parent body of the IIA irons.

Evaluation of frictional melting on the basis of trace element analyses of fault rocks

NASA Astrophysics Data System (ADS)

Ishikawa, T.; Ujiie, K.

2016-12-01

Pseudotachylytes (solidified frictional melts produced during seismic slip) found in exhumed accretionary complexes are considered to have formed originally at seismogenic depths, and help our understanding of the dynamics of earthquake faulting in subduction zones. The frictional melting should affect rock chemistry. Actually, major element compositions of unaltered pseudotachylyte matrix in the Shimanto accretionary complex are reported to be similar to that of illite, implying disequilibrium melting in the slip zone (Ujiie et al., 2007). Bulk-rock trace element analyses of the pseudotachylyte-bearing fault rocks also revealed their shift to the clay-mineral-like compositions (Honda et al., 2011). Toward better understanding of the frictional melting using chemical means, we carried out detailed major and trace element analyses for pseudotachylyte-bearing dark veins and surrounding host rocks from the Mugi area of the Shimanto accretionary complex (Ujiie et al., 2007). About one milligram each of samples was collected from a rock chip along the microstructure by using the PC-controlled micro-drilling apparatus, and then analyzed by ICP-MS. Host rocks showed a series of compositional trends controlled by mixing of detrital sedimentary components. Unaltered part of the pseudotachylyte vein, on the other hand, showed striking enrichment of fluid-immobile trace elements, consistent with selective melting of fine-grained, clay-rich matrix of the fault rock. Importantly, completely altered parts of the dark veins exhibit essentially the same characteristics as the unaltered part, indicating that the trace element composition of the pseudotachylyte is well preserved even after considerable alteration in the later stages. These results demonstrate that trace element and structural analyses are useful to detect preexistence of pseudotachylytes resulting from selective frictional melting of clay minerals. It has been controversial that pseudotachylytes are rarely formed or rarely preserved. Trace element analyses on clay-rich localized slipping zones shed light on this topic. References: Ujiie et al. (2007) J. Struct. Geol. 29, 599-613; Honda et al. (2011) GRL 38, L06310.

A temporal record of pre-eruptive magmatic volatile contents at Campi Flegrei: Insights from texturally-constrained apatite analyses

NASA Astrophysics Data System (ADS)

Stock, Michael J.; Isaia, Roberto; Humphreys, Madeleine C. S.; Smith, Victoria C.; Pyle, David M.

2016-04-01

Apatite is capable of incorporating all major magmatic volatile species (H2O, CO2, S, Cl and F) into its crystal structure. Analysis of apatite volatile contents can be related to parental magma compositions through the application of pressure and temperature-dependent exchange reactions (Piccoli and Candela, 1994). Once included within phenocrysts, apatite inclusions are isolated from the melt and preserve a temporal record of magmatic volatile contents in the build-up to eruption. In this work, we measured the volatile compositions of apatite inclusions, apatite microphenocrysts and pyroxene-hosted melt inclusions from the Astroni 1 eruption of Campi Flegrei, Italy (Stock et al. 2016). These data are coupled with magmatic differentiation models (Gualda et al., 2012), experimental volatile solubility data (Webster et al., 2014) and thermodynamic models of apatite compositional variations (Piccoli and Candela, 1994) to decipher pre-eruptive magmatic processes. We find that apatite halogen/OH ratios decreased through magmatic differentiation, while melt inclusion F and Cl concentrations increased. Melt inclusion H2O contents are constant at ~2.5 wt%. These data are best explained by volatile-undersaturated differentiation over most of the crystallisation history of the Astroni 1 melt, with melt inclusion H2O contents reset at shallow levels during ascent. Given the high diffusivity of volatiles in apatite (Brenan, 1993), the preservation of volatile-undersaturated melt compositions in microphenocrysts suggests that saturation was only achieved 10 - 103 days before eruption. We suggest that late-stage transition into a volatile-saturated state caused an increase in magma chamber overpressure, which ultimately triggered the Astroni 1 eruption. This has major implications for monitoring of Campi Flegrei and other similar volcanic systems. Piccoli and Candela, 1994. Am. J. of Sc., 294, 92-135. Stock et al., 2016, Nat. Geosci. Gualda et al., 2012. J. Pet., 53, 875-890. Webster et al., 2014. J. Pet., 55, 2217-2248. Brenan, 1993. Chem. Geol., 110, 195-210.

Apatite-Melt Partitioning of Volatiles in Basaltic Systems: Implications for Determining Volatile Abundances in Planetary Bodies from Apatite

NASA Technical Reports Server (NTRS)

McCubbin, F. M.

2017-01-01

Apatite [Ca5(PO4)3(F,Cl,OH)] is present in a wide range of planetary materials, and due to the presence of volatiles within its crystal structure (X-site), many recent studies have attempted to use apatite to constrain the volatile contents of planetary magmas and mantle sources [i.e., 1]. Experimental studies have investigated the apatite-melt partitioning behavior of F, Cl, and OH in basaltic systems [e.g., 2- 3], reporting that apatite-melt partitioning of volatiles is best described as exchange equilibria similar to Fe-Mg partitioning between olivine and silicate melt. However, exchange coefficients may vary as a function of temperature, pressure, melt composition, and/or oxygen fugacity. Furthermore, exchange coefficients may vary in portions of apatite compositional space where F, Cl, and OH do not mix ideally in apatite [3]. In these regions of ternary space, we anticipate that crystal chemistry could influence partitioning behavior. Consequently, we conducted experiments to investigate the effect of apatite crystal chemistry on apatite-melt partitioning of F, Cl, and OH.

Core Formation on Asteroid 4 Vesta: Iron Rain in a Silicate Magma Ocean

NASA Technical Reports Server (NTRS)

Kiefer, Walter S.; Mittlefehldt, David W.

2017-01-01

Geochemical observations of the eucrite and diogenite meteorites, together with observations made by NASA's Dawn spacecraft, suggest that Vesta resembles H chondrites in bulk chemical composition, possibly with about 25% of a CM-chondrite like composition added in. For this model, the core is 15% by mass (or 8 volume %) of the asteroid. The abundances of moderately siderophile elements (Ni, Co, Mo, W, and P) in eucrites require that essentially all of the metallic phase in Vesta segregated to form a core prior to eucrite solidification. Melting in the Fe-Ni-S system begins at a cotectic temperature of 940 deg. C. Only about 40% of the total metal phase, or 3-4 volume % of Vesta, melts prior to the onset of silicate melting. Liquid iron in solid silicate initially forms isolated pockets of melt; connected melt channels, which are necessary if the metal is to segregate from the silicate, are only possible when the metal phase exceeds about 5 volume %. Thus, metal segregation to form a core does not occur prior to the onset of silicate melting.

Stability and growth of continental shields in mantle convection models including recurrent melt production

NASA Astrophysics Data System (ADS)

de Smet, J. H.; van den Berg, A. P.; Vlaar, N. J.

1998-10-01

The long-term growth and stability of compositionally layered continental upper mantle has been investigated by numerical modelling. We present the first numerical model of a convecting mantle including differentiation through partial melting resulting in a stable compositionally layered continental upper mantle structure. This structure includes a continental root extending to a depth of about 200 km. The model covers the upper mantle including the crust and incorporates physical features important for the study of the continental upper mantle during secular cooling of the Earth since the Archaean. Among these features are: a partial melt generation mechanism allowing consistent recurrent melting, time-dependent non-uniform radiogenic heat production, and a temperature- and pressure-dependent rheology. The numerical results reveal a long-term growth mechanism of the continental compositional root. This mechanism operates through episodical injection of small diapiric upwellings from the deep layer of undepleted mantle into the continental root which consists of compositionally distinct depleted mantle material. Our modelling results show the layered continental structure to remain stable during at least 1.5 Ga. After this period mantle differentiation through partial melting ceases due to the prolonged secular cooling and small-scale instabilities set in through continental delamination. This stable period of 1.5 Ga is related to a number of limitations in our model. By improving on these limitations in the future this stable period will be extended to more realistic values.

Magma storage constrains by compositional zoning of plagioclase from dacites of the caldera forming eruptions of Vetrovoy Isthmus and Lvinaya Past’ Bay (Iturup Island, Kurile Islands)

NASA Astrophysics Data System (ADS)

Maksimovich, I. A.; Smirnov, S. Z.; Kotov, A. A.; Timina, T. Yu; Shevko, A. V.

2017-12-01

The Vetrovoy Isthmus and the Lvinaya Past’ Bay on the Iturup island (Kuril island arc) are the results of large Plinian eruptions of compositionally similar dacitic magmas. This study is devoted to a comparative analysis of the storage and crystallization conditions for magma reservoirs, which were a source of large-scale explosive eruptions. The plagioclase is most informative mineral in studying of the melt evolution. The studied plagioclases possess a complex zoning patterns, which are not typical for silicic rocks in island-arc systems. It was shown that increase of Ca in the plagioclase up to unusually high An95 is related to increase of H2O pressure in both volcanic magma chambers. The study revealed that minerals of the Vetrovoy Isthmus and Lvinaya Past’ crystallized from compositionally similar melts. Despite the compositional similarity of the melts, the phenocryst assemblage of the Lvinaya Past’ differs from the Vetrovoy Isthmus by the presence of the amphibole, which indicates that the pressure in the magmatic chamber exceeded 1-2 kbar at a 4-6 wt. % of H2O in the melt. The rocks of the Vetrovoy Isthmus do not contain amphibole phenocrysts, but melt and fluid inclusions assemblages in plagioclase demonstrate that the magma degassed in the course of evolution. This is an indication that the pressure did not exceed significantly 1-2 kbar.

A fully coupled petrological geodynamical model to investigate the evolution of crustal magma chambers

NASA Astrophysics Data System (ADS)

Rummel, Lisa; Kaus, Boris J. P.; White, Richard W.

2017-04-01

The evolution of crustal magma chambers can be considered from a range of different physical and chemical perspectives. Most previous studies focus either on the petrological side (assuming only thermal effects and ignoring mechanics), or on the mechanical evolution (assuming a fixed melt chemistry). Here, we develop a method that fully couples petrological with geodynamic modelling, by combining a finite element code, MVEP2, with a thermodynamic modelling approach (Perple_X) that takes the evolving chemistry into account. The evolution of melt chemistry in a crustal magma chamber is analyzed by focusing on the effects of depth and temperature as well as size and shape of the magma chamber(s). The models show that each of these factors influences the melting behavior of rocks, the magma composition and their effects on the mechanics in the upper lithosphere. Interactions with country rocks (assimilation), ongoing rock depletion (fractional melting) and a possible open system behavior (fractional crystallization) and their effects on magma chemistry are taken into account. The chemical and mineralogical evolution of the melt source, composition (10 oxide component system) of intrusive and extrusive rocks as well as melt fraction and density are tracked on particles using a marker-in-cell-method in the geodynamic code. After each melt extraction event, the employed phase diagram is updated or recalculated based on the residuum chemistry that shifts the solidus to higher temperatures with sequential melt extraction. The resulting wide range in chemical compositions and the volume of intrusive and extrusive rocks are tracked in time and space over the melting region. The newly generated crust employs phase diagrams which are directly computed from the chemistry of extracted melts. Plutons are able to melt again as long as the local temperature is higher in the model than the solidus temperature in the employed phase diagram. As a result, our models make testable predictions on types of erupted lavas. We show an application to the plume-related intracontinental West Eifel volcanism (Germany), where our models explain a sudden change in K2O/Na2O-ratios in the volcanic rocks by a transition between melting a metasomatized and a pyrolitic mantle. We also show initial results from crustal melt extraction in an arc system.

Carbonatite and silicate melt metasomatism of the mantle surrounding the Hawaiian plume: Evidence from volatiles, trace elements, and radiogenic isotopes in rejuvenated-stage lavas from Niihau, Hawaii

NASA Astrophysics Data System (ADS)

Dixon, Jacqueline; Clague, David A.; Cousens, Brian; Monsalve, Maria Luisa; Uhl, Jessika

2008-09-01

We present new volatile, trace element, and radiogenic isotopic compositions for rejuvenated-stage lavas erupted on Niihau and its submarine northwest flank. Niihau rejuvenated-stage Kiekie Basalt lavas are mildly alkalic and are isotopically similar to, though shifted to higher 87Sr/86Sr and lower 206Pb/204Pb than, rejuvenated-stage lavas erupted on other islands and marginal seafloor settings. Kiekie lavas display trace element heterogeneity greater than that of other rejuvenated-stage lavas, with enrichments in Ba, Sr, and light-rare earth elements resulting in high and highly variable Ba/Th and Sr/Ce. The high Ba/Th lavas are among the least silica-undersaturated of the rejuvenated-stage suite, implying that the greatest enrichments are associated with the largest extents of melting. Kiekie lavas also have high and variable H2O/Ce and Cl/La, up to 620 and 39, respectively. We model the trace element concentrations of most rejuvenated-stage lavas by small degrees (˜1% to 9%) of melting of depleted peridotite recently metasomatized by a few percent of an enriched incipient melt (0.5% melting) of the Hawaiian plume. Kiekie lavas are best explained by 4% to 13% partial melting of a peridotite source metasomatized by up to 0.2% carbonatite, similar in composition to oceanic carbonatites from the Canary and Cape Verde Islands, with lower proportion of incipient melt than that for other rejuvenated-stage lavas. Primary H2O and Cl of the carbonatite component must be high, but variability in the volatile data may be caused by heterogeneity in the carbonatite composition and/or interaction with seawater. Our model is consistent with predictions based on carbonated eclogite and peridotite melting experiments in which (1) carbonated eclogite and peridotite within the Hawaiian plume are the first to melt during plume ascent; (2) carbonatite melt metasomatizes plume and surrounding depleted peridotite; (3) as the plume rises, silica-undersaturated silicate melts are also produced and contribute to the metasomatic signature. The metasomatic component is best preserved at the margins of the plume, where low extents of melting of the metasomatized depleted mantle surrounding the plume are sampled during flexural uplift. Formation of carbonatite melts may provide a mechanism to transfer plume He to the margins of the plume.

Experimental study of the electrolysis of silicate melts

NASA Technical Reports Server (NTRS)

Keller, R.; Larimer, K. T.

1991-01-01

To produce oxygen from lunar resources, it may be feasible to melt and electrolyze local silicate ores. This possibility was explored experimentally with synthesized melts of appropriate compositions. Platinum electrodes were employed at a melt temperature of 1425 C. When silicon components of the melt were reduced, the platinum cathode degraded rapidly, which prompted the substitution of a graphite cathode substrate. Discrete particles containing iron or titanium were found in the solidified electrolyte after three hours of electrolysis. Electrolyte conductivities did not decrease substantially, but the escape of gas bubbles, in some cases, appeared to be hindered by high viscosity of the melt.

The role of liquid-liquid immiscibility and crystal fractionation in the genesis of carbonatite magmas: insights from Kerimasi melt inclusions

NASA Astrophysics Data System (ADS)

Guzmics, Tibor; Zajacz, Zoltán; Mitchell, Roger H.; Szabó, Csaba; Wälle, Markus

2015-02-01

We have reconstructed the compositional evolution of the silicate and carbonate melt, and various crystalline phases in the subvolcanic reservoir of Kerimasi Volcano in the East African Rift. Trace element concentrations of silicate and carbonate melt inclusions trapped in nepheline, apatite and magnetite from plutonic afrikandite (clinopyroxene-nepheline-perovskite-magnetite-melilite rock) and calciocarbonatite (calcite-apatite-magnetite-perovskite-monticellite-phlogopite rock) show that liquid immiscibility occurred during the generation of carbonatite magmas from a CO2-rich melilite-nephelinite magma formed at relatively high temperatures (1,100 °C). This carbonatite magma is notably more calcic and less alkaline than that occurring at Oldoinyo Lengai. The CaO-rich (32-41 wt%) nature and alkali-"poor" (at least 7-10 wt% Na2O + K2O) nature of these high-temperature (>1,000 °C) carbonate melts result from strong partitioning of Ca (relative to Mg, Fe and Mn) in the immiscible carbonate and the CaO-rich nature (12-17 wt%) of its silicate parent (e.g., melilite-nephelinite). Evolution of the Kerimasi carbonate magma can result in the formation of natrocarbonatite melts with similar composition to those of Oldoinyo Lengai, but with pronounced depletion in REE and HFSE elements. We suggest that this compositional difference results from the different initial parental magmas, e.g., melilite-nephelinite at Kerimasi and a nephelinite at Oldoinyo Lengai. The difference in parental magma composition led to a significant difference in the fractionating mineral phase assemblage and the element partitioning systematics upon silicate-carbonate melt immiscibility. LA-ICP-MS analysis of coeval silicate and carbonate melt inclusions provides an opportunity to infer carbonate melt/silicate melt partition coefficients for a wide range of elements. These data show that Li, Na, Pb, Ca, Sr, Ba, B, all REE (except Sc), U, V, Nb, Ta, P, Mo, W and S are partitioned into the carbonate melt, whereas Mg, Mn, Fe, Co, Cu, Zn, Al, Sc, Ti, Hf and Zr are partitioned into the silicate melt. Potassium and Rb show no preferential partitioning. Kerimasi melt inclusions show that the immiscible calcic carbonate melt is strongly enriched in Sr, Ba, Pb, LREE, P, W, Mo and S relative to other trace elements. Comparison of our data with experimental results indicates that preferential partitioning of oxidized sulfur (as SO4 2-), Ca and P (as PO4 3-) into the carbonate melt may promote the partitioning of Nb, Ta, Pb and all REE, excluding Sc, into this phase. Therefore, it is suggested that P and S enrichment in calcic carbonate magmas promotes the genesis of REE-rich carbonatites by liquid immiscibility. Our study shows that changes in the partition coefficients of elements between minerals and the coexisting melts along the liquid line of descent are rather significant at Kerimasi. This is why, in addition to the REE, Nb, Ta and Zr are also enriched in Kerimasi calciocarbonatites. We consider significant amounts of apatite and perovskite precipitated from melilite-nephelinite-derived carbonate melt as igneous minerals can have high LREE, Nb and Zr contents relative to other carbonatite minerals.

An empirical method for calculating melt compositions produced beneath mid-ocean ridges: for axis and off-axis (seamounts) melting application

NASA Astrophysics Data System (ADS)

Batiza, Rodey

1991-12-01

We present a new method for calculating the major element compositions of primary melts parental to mid-ocean ridge basalt (MORB). This model is based on the experimental data of Jaques and Green (1980), Falloon et al. (1988), and Falloon and Green (1987, 1988) which are ideal for this purpose. Our method is empirical and employs solid-liquid partition coefficients (Di) from the experiments. We empirically determine Di=f(P,F) and use this to calculate melt compositions produced by decompression-induced melting along an adiabat (column melting). Results indicate that most MORBs can be generated by 10-20% partial melting at initial pressures (P0) of 12-21 kbar. Our primary MORB melts have MgO=10-12 wt %. We fractionate these at low pressure to an MgO content of 8.0 wt% in order to interpret natural MORB liquids. This model allows us to calculate Po, Pf, To, Tf, and F for natural MORB melts. We apply the model to interpret MORB compositions and mantle upwelling patterns beneath a fast ridge (East Pacific Rise (EPR) 8°N to 14°N), a slow ridge (mid-Atlantic Ridge (MAR) at 26°S), and seamounts near the EPR (Lamont seamount chain). We find mantle temperature differences of up to 50°-60°C over distances of 30-50 km both across axis and along axis at the EPR. We propose that these are due to upward mantle flow in a weakly conductive (versus adiabatic) temperature gradient. We suggest that the EPR is fed by a wide (~100 km) zone of upwelling due to plate separation but has a central core of faster buoyant flow. An along-axis thermal dome between the Siqueiros transform and the 11°45' Overlapping Spreading Center (OSC) may represent such an upwelling; however, in general there is a poor correlation between mantle temperature, topography, and the segmentation pattern at the EPR. For the Lamont seamounts we find regular across-axis changes in Po and F suggesting that the melt zone pinches out off axis. This observation supports the idea that the EPR is fed by a broad upwelling which diminishes in vigor off axis. In contrast with the EPR axis, mantle temperature correlates well with topography at the MAR, and there is less melting under offsets. The data are consistent with weaker upwelling under offsets and a adiabatic temperature gradient in the subaxial mantle away from offsets. The MAR at 26°S exhibits the so-called local trend of Klein and Langmuir (1989). Our model indicates that the local trend cannot be due solely to intracolumn melting processes. The local trend seems to be genetically associated with slow-spreading ridges, and we suggest it is due to melting of multiple individual domains that differ in initial and final melting pressure within segments fed by buoyant focused mantle flow.

An empirical method for calculating melt compositions produced beneath mid-ocean ridges: Application for axis and off-axis (seamounts) melting

NASA Astrophysics Data System (ADS)

Niu, Yaoling; Batiza, Rodey

1991-12-01

We present a new method for calculating the major element compositions of primary melts parental to mid-ocean ridge basalt (MORB). This model is based on the experimental data of Jaques and Green (1980), Falloon et al. (1988), and Falloon and Green (1987, 1988) which are ideal for this purpose. Our method is empirical and employs solid-liquid partition coefficients (Di) from the experiments. We empirically determine Di = ƒ(P,F) and use this to calculate melt compositions produced by decompression-induced melting along an adiabat (column melting). Results indicate that most MORBs can be generated by 10-20% partial melting at initial pressures (P0) of 12-21 kbar. Our primary MORB melts have MgO = 10-12 wt %. We fractionate these at low pressure to an MgO content of 8.0 wt % in order to interpret natural MORB liquids. This model allows us to calculate Po, Pƒ, To, Tƒ, and F for natural MORB melts. We apply the model to interpret MORB compositions and mantle upwelling patterns beneath a fast ridge (East Pacific Rise (EPR)8°N to 14°N), a slow ridge (mid-Atlantic Ridge (MAR) at 26°S), and seamounts near the EPR (Lament seamount chain). We find mantle temperature differences of up to 50°-60°C over distances of 30-50 km both across axis and along axis at the EPR. We propose that these are due to upward mantle flow in a weakly conductive (versus adiabatic) temperature gradient. We suggest that the EPR is fed by a wide (-100 km) zone of upwelling due to plate separation but has a central core of faster buoyant flow. An along-axis thermal dome between the Siqueiros transform and the 11°45' Overlapping Spreading center (OSC) may represent such an upwelling; however, in general there is a poor correlation between mantle temperature, topography, and the segmentation pattern at the EPR. For the Lament seamounts we find regular across-axis changes in Po and F suggesting that the melt zone pinches out off axis. This observation supports the idea that the EPR is fed by a broad upwelling which diminishes in vigor off axis. In contrast with the EPR axis, mantle temperature correlates well with topography at the MAR, and there is less melting under offsets. The data are consistent with weaker upwelling under offsets and an adiabatic temperature gradient in the sub axial mantle away from offsets. The MAR at 26°S exhibits the so-called local trend of Klein and Langmuir (1989). Our model indicates that the local trend cannot be due solely to intracolumn melting processes. The local trend seems to be genetically associated with slow-spreading ridges, and we suggest it is due to melting of multiple individual domains that differ in initial and final melting pressure within segments fed by buoyant focused mantle flow.

Enceladus: three-act play and current state

NASA Astrophysics Data System (ADS)

Luan, J.; Goldreich, P.

2017-12-01

Eccentricity (e) growth as Enceladus migrates deeper into mean motion resonance with Dione results in increased tidal heating. As the bottom of the ice shell melts, the rate of tidal heating jumps and runaway melting ensues. At the end of run-away melting, the shell's thickness has fallen below the value at which the frequency of free libration equals the orbital mean motion and e has damped to well below its current value. Subsequently, both the shell thickness and e partake in a limit cycle. As e damps toward its minimum value, the shell's thickness asymptotically approaches its resonant value from below. After minimum e, the shell thickens quickly and e grows even faster. This cycle is likely to have been repeated multiple times in the past. Currently, e is much smaller than its equilibrium value corresponding to the shell thickness. Physical libration resonance resolves this mystery, it ensures that the low-e and medium-thickness state is present for most of the time between consecutive limit cycles. It is a robust scenario that avoids fine tuning or extreme parameter choice, and naturally produces episodic stages of high heating, consistent with softening of topographical features on Enceladus.

Picritic glasses from Hawaii

USGS Publications Warehouse

Clague, D.A.; Weber, W.S.; Dixon, J.E.

1991-01-01

ESTIMATES of the MgO content of primary Hawaiian tholeiitic melts range from 8wt% to as high as 25wt% (refs 1, 2). In general, these estimates are derived from analysis of the whole-rock composition of lavas, coupled with the compositions of the most magnesian olivine phenocrysts observed. But the best estimate of magma composition comes from volcanic glass, as it represents the liquid composition at the time of quenching; minimal changes occur during the quenching process. Here we report the discovery of tholeiitic basalt glasses, recovered offshore of Kilauea volcano, that contain up to 15.0 wt% MgO. To our knowledge, these are the most magnesian glasses, and have the highest eruption temperatures (??? 1,316 ??C), yet found. The existence of these picritic (high-MgO) liquids provides constraints on the temperature structure of the upper mantle, magma transport and the material and thermal budgets of the Hawaiian volcanoes. Furthermore, picritic melts are affected little by magma-reservoir processes, and it is therefore relatively straightforward to extrapolate back to the composition of the primary melt and its volatile contents.

Developing a Hygrometer for Water-Undersaturated Lherzolite Melts

NASA Astrophysics Data System (ADS)

Guild, M. R.; Till, C. B.

2017-12-01

The effect of water on the composition of primitive mantle melts at arc volcanoes is a topic of wide interest and has been addressed in a number of previous experimental studies including Hirose & Kawamoto (1995), Gaetani & Grove (1998), Till et al. (2012) and Mitchell & Grove (2015). The current study builds upon the work by previous authors in an effort to develop a more robust hygrometer for primitive lherzolite melts at water-undersaturated conditions. The starting composition for this experimental study is a mixture of 75% primitive upper mantle and 25% primitive basalt (Baker et al., 1991) with a bulk H2O content of 2 wt. %. Experiments were performed at Arizona State University in the Experimental Petrology and Igneous processes Center (EPIC) from 1.2-1.6 GPa at 1150-1300 ºC for 2 days in a piston cylinder apparatus to reflect conditions relevant for arc melt equilibration (Till 2017). A double capsule design was used to prevent Fe and H2O loss with an inner Fe-presaturated Au80Pd20 capsule and an outer Au80Pd20 capsule. Run products were analyzed by electron microprobe and determined to be successful when they demonstrated 0-5% Fe-loss, olivine-melt KDs of 0.27-0.30, and minimal H2O loss. The water-undersaturated melt composition are in equilibrium with ol+opx+sp±cpx. Run products at 1.6 GPa do not contain cpx in the mineral assemblage over the studied temperature range. Observed melt compositions have SiO2 contents of 48-49 wt. % at 1.2 GPa and 46-49 wt.% at 1.6 GPa. Our experimental results suggest an enhanced effect of water on increasing the SiO2 content of the melt compared to previous studies on systems with similar water contents and anhydrous systems. Baker, et al., JGR 96, 21819-21842 (1991). Gaetani & Grove, CMP 131, 323-346 (1998). Hirose & Kawamoto, EPSL 133, 463-473 (1995). Mitchell & Grove, CMP 170, 13 (2015). Till, Am. Mineral, 102, 931-947 (2017). Till, et al., JGR 117 (2012).

Production of fiberglass/metal composite material suitable for building habitat and manufacturing facilities

NASA Technical Reports Server (NTRS)

1987-01-01

The production of a fiberglass/metal composite material suitable for building habitats and manufacturing facilities was the project for Clemson. The concept and development of the knowledge necessary to produce glass fibers originated in the spring semester. During the summer, while at Johnson Space Center, fiberglass from a rock composition similar to ones found at the Apollo 16 site on the moon was successfully produced. The project this year was a continuation of last year's studies. We addressed the following problems which emerged as the work progressed: (1) Methods for coating the fibers with a metal were explored. We manufactured composites in two stages: Glass fibers without any coating on them; and fibers coated with metals as they were made. This proved to be a difficult process. Future activities include using a chemical vapor deposition process on fibers which have been made. (2) A glass furnace was developed which relies primarily on solar energy for melting the glass. The temperature of the melted glass is maintained by electrical means. The design is for 250 kg of glass per day. An electrical engineering student developed a scheme for controlling the melting and manufacturing process from the earth. This was done to minimize the human risk. Graphite refractories are relied on to contain the melt. (3) The glass composition chosen for the project is a relatively pure anorthite which is available in the highland regions of the lunar surface. A major problems with this material is that it melts at a comparatively high temperature. This problem will be solved by using graphite refractory materials for the furnace. The advantage of this glass composition is that it is very stable and does not tend to crystallize. (4) We have also refined the experimental furnace and fiber making machinery which we will be using at Johnson Space Center this summer. We believe that we will be able to draw and coat glass fibers in a vacuum for use in composites. We intend to make and test the mechanical properties of these composites.

Mafic intrusion remobilising silicic magma under El Hierro, Canary Islands

NASA Astrophysics Data System (ADS)

Sigmarsson, O.; Laporte, D.; Marti, J.; Devouard, B.; Cluzel, N.

2012-04-01

The 2011 submarine eruption at El Hierro, Canary Islands, has produced volcanic bombs that degas at sea surface, boil seawater and sink when cooled and degassed. At the beginning of the eruption white coloured pumices enveloped in darker coloured spatters floated on land. These composite pumices show evidence of magma mingling with folds and undulations of the darker coloured magma within the white pumice suggesting magma mingling in a viscous regime. The white pumice is highly vesicular and resembles foam. Most of the vesicular structure is made of tightly packed, polygonal bubbles of uniform size (˜ 100 μm), suggesting a single event of homogeneous bubble nucleation. An earlier event of heterogeneous bubble nucleation is indicated by the presence of a few large bubbles developed around tiny quartz crystals. Both the darker and lighter coloured pumices are almost aphyric. A few olivine crystals with perfect euhedral morphology occur within the darker part. Rare olivines of same composition are also found in the white pumice glass but then display somewhat rounded outlines and hopper-type structure. Melt inclusions in olivines of the darker pumice are of the same composition as the enveloping mafic glass, whereas olivines in the mixing boundary layer have melt inclusions of less mafic composition. The whole-rock composition and slightly more evolved glass composition are of basanitc and alkali rhyolitic composition (at the limit of the trachyte field) according to the TAS classification. Such rhyolitic compositions are rare in the Canaries. Analyses of residual volatile concentration in the glasses show that the silicic glass is highly degassed (F: 511 ±222; Cl: 202 ±58; S: below detection limit; values in ppm,1SD, n=10), whereas the basanitic glass still has very high halogene concentrations (F: 1354 ±151; Cl: 1026 ±47; S: 362 ±29; 1SD, n=10). In-situ analysis of trace element compositions of the dark glasses reveal typical basanitic compositions with elevated incompatible element concentrations and primitive mantle normalised spectra characteristic for the Canary Island basanites (e.g. La is of 100 times higher concentration than primitive mantle with important LREE enrichments). In contrast, the trace element composition of the alkali rhyolite shows surprisingly low concentrations for all elements except the most incompatible ones (such as Rb, Ba, K and Th). All other measured incompatible LILE, HFSE and REE have significantly lower concentration than the basanitic counterpart. This differences increase with the atomic number of the REE reaching maximum for the MREE and thus forming an intriguing U-shaped rhyolite spectra. Furthermore, unusual U-depletion is observed in the rhyolite. Other negative spikes, such as those for Sr and P, are readily accounted for by the removal of plagioclase and apatite during magma evolution from a basanite to a more evolved melt. The results obtained so far suggest an intrusion of gas-rich basanitic melt at the base of an evolved intrusion remobilising a stagnant phonolitic melt present as late differentiate in the crust. Interaction with old oceanic crust and the volcanic edifice can be quantified and shown to have modified the phonolite melt composition and produced the alkali rhyolitic composition of the white floating pumice. Extensive gas exsolution shortly before the melt-glass transition explains the foam texture and the low volatile concentrations in the quenched alkali rhyolite.

Petrological Constraints on Melt Generation Beneath the Asal Rift (Djibouti)

NASA Astrophysics Data System (ADS)

Pinzuti, P.; Humler, E.; Manighetti, I.; Gaudemer, Y.; Bézos, A.

2010-12-01

The temporal evolution of the mantle melting processes in the Asal Rift is evaluated from the chemical composition of 95 lava flows sampled along 10 km of the rift axis and 8 km off-axis (that is for the last 650 ky). The major element composition and the trace element ratios of aphyric basalts across the Asal Rift show a symmetric pattern relative to the rift axis and preserved a clear signal of mantle melting depth variations. FeO, Fe8.0, Sm/YbN and Zr/Y increase, whereas SiO2 and Lu/HfN decrease from the rift axis to the rift shoulders. These variations are qualitatively consistent with a shallower melting beneath the rift axis than off-axis and the data show that the melting regime is inconsistent with a passive upwelling model. In order to quantify the depth range and extent of melting, we invert Na8.0 and Fe8.0 contents of basalts based on a pure active upwelling model. Beneath the rift axis, melting paths are shallow, from 60 to 30 km. These melting paths are consistent with adiabatic melting in normal-temperature asthenosphere, beneath an extensively thinned mantle lithosphere. In contrast, melting on the rift shoulders occurred beneath a thick mantle lithosphere and required mantle solidus temperature 180°C hotter than normal (melting paths from 110 to 75 km). The calculated rate of lithospheric thinning is high (6.0 cm yr-1) and could explain the survival of a metastable garnet within the mantle at depth shallower than 90 km beneath the modern Asal Rift.

Mesozoic crustal thickening of the eastern North China craton: Evidence from eclogite xenoliths and petrologic implications

NASA Astrophysics Data System (ADS)

Xu, Wenliang; Gao, Shan; Wang, Qinghai; Wang, Dongyan; Liu, Yongsheng

2006-09-01

A suite of xenoliths of eclogite, garnet clinopyroxenite, and felsic gneiss is found in Early Cretaceous high-Mg [Mg# >45, where Mg# = molar 100 × Mg/(Mg + Fetotal)] adakitic intrusions from the Xuzhou-Huaibei (Xu-Huai) region along the southeastern margin of the North China craton. The primary mineral assemblage of garnet + omphacite/augite + quartz + rutile ± pargasite of the eclogite and garnet clinopyroxenite xenoliths defines a minimum pressure of >1.5 GPa, while the estimated peak metamorphic temperatures range from 800 to 1060 °C. An Sm-Nd whole-rock garnet isochron and zircon U-Pb dates show that timing of the eclogite facies metamorphism took place ca. 220 Ma. This Triassic age agrees with the age of eclogites from the Dabie-Sulu ultrahigh-pressure metamorphic (UHPM) belt. The ages of abundant Late Archean to early Paleoproterozoic (2.3 2.6Ga) inherited zircons correspond to the most prominent crustal growth event in the North China craton. In addition, these xenoliths and their host high-Mg adakitic intrusions have complementary major and trace element compositions, suggesting that the adakites formed by partial melting of Archean metabasalts that were the protoliths of the Xu-Huai eclogite and garnet clinopyroxenite xenoliths. Trace element and Sr-Nd isotopic modeling shows that the high-Mg adakitic intrusions can be modeled as melts from ˜40% partial melting of the metabasalts in the eclogite facies, followed by interaction with the convecting mantle and variable degrees of crustal assimilation. Together with the similar zircon age populations between the xenoliths and the host rocks, these lines of evidence strongly suggest their genetic link via thickening, foundering, and partial melting of the Archean North China craton mafic lower crust, followed by adakitic melt-mantle interaction. The crustal thickening resulted from Triassic collision between the Yangtze craton and the North China craton, which produced the Dabie-Sulu UHPM belt in the subducting Yangtze plate and eclogitization of the basaltic crustal root of the overriding North China craton plate. Such processes may have played an important role in generating the high-Mg character of the continental crust.

Evolution of major and trace elements and volatile contents of selected magmas in the Campi Flegrei and Procida volcanic fields, Italy, based on melt inclusion

NASA Astrophysics Data System (ADS)

Esposito, R.; Badescu, K.; Steele-MacInnis, M.; Lima, A.; De Vivo, B.; Cannatelli, C.; Manning, C. E.; Bodnar, R. J.

2017-12-01

The active Campi Flegrei (CF) volcanic field in southern Italy has been intensively studied owing to the volcanic risk to which the 1.5 million people in the area are exposed. The volcanic Island of Procida (IP) is located just southwest from CF but shows no signs of volcanic activity today. The IP volcanic products are the most primitive volcanic products of these two related volcanic fields. In this study, the major and minor element and volatile (H2O, CO2, S, Cl and F) compositions of melt inclusions (MI) hosted in sanidine, clinopyroxene, plagioclase and olivine were determined. MI data from this study and from the literature were compared with bulk rock data to test for agreement between MI compositions and compositions of CF and IP magmas determined by bulk rock analyses. Although MI compositions overlap with those of the bulk rock, some MI show anomalous compositions for one or a combination of Al2O3, FeO, P2O5, and TiO2. These MI represent melts produced by dissolution-reaction-mixing and were not included for the interpretation of volatile contents. Major elements and volatile concentrations of bubble-free MI that are interpreted to be representative of CF and IP were compared to crystal host compositions and to melt compositions obtained using rhyolite-MELTS simulations. Data suggest that less evolved magmas beneath the studied area crystallize either isobarically at ≥200 MPa (≥7.5 km) or polybarically during ascent to shallow depths under volatile-saturated conditions. Bubble-free MI representative of the least differentiated magmas can be divided into two groups. One group of MI is representative of simple fractional crystallization under volatile-saturated conditions from a primitive trachybasaltic melt. The other group of MI is representative of recharge of a primitive basaltic magma mixing with the preexisting primitive trachybasaltic magma before eruption. We suggest that the mixing process occurred at relatively great depth. Extensive isobaric crystallization of the trachybasaltic magmas beneath CF at 7.5 km may have generated trachy-phonolitic magmas, such as those associated with the Neapolitan Yellow Tuff that is characterized by a relatively high H2O content. These volatile saturated trachy-phonolitic magmas ascend through the crust and trigger high-magnitude eruptions.

The Changing Nature of the Hawaiian Hotspot in the Late Cretaceous-Early Tertiary: Evidence From Helium Isotopes and Melt Inclusion Compositions

NASA Astrophysics Data System (ADS)

Keller, R.; Graham, D.; Duncan, R.; Regelous, M.

2002-12-01

Ocean Drilling Program Leg 197 recovered basaltic basement from three of the Late Cretaceous-Paleogene Emperor seamounts: Detroit (Sites 1203 and 1204), Nintoku (Site 1205), and Koko (Site 1206) seamounts. The depths of penetration into basement achieved by this drilling (140-450 m), the range of rock types recovered (hawaiites, alkalic basalts, and tholeiitic basalts), and the age range (48-76 Ma) makes this one of the most comprehensive collections of the volcanic products of the Hawaiian hotspot available, and opens up new opportunities to study the temporal evolution of the Hawaiian hotspot during the Late Cretaceous and early Tertiary. Previous studies of the chemical evolution of the Hawaiian hotspot (Lanphere et al., 1980; Keller et al., 2000) found significant temporal variations. For example, Sr isotopic ratios of the tholeiitic basalts remain fairly constant along the Hawaiian Islands/Ridge between Kilauea volcano on Hawaii and the Hawaiian-Emperor bend, but then decrease steadily northward along the Emperor seamounts. Trace element compositions (especially the rare earth element patterns) also show limited variations along the Hawaiian Islands/Ridge, but change toward more depleted values northward along the Emperor seamounts. The trend to more MORB-like compositions back in time was attributed to a decrease in distance between the hotspot and the nearest spreading center, although a more comprehensive study suggests that variations in lithospheric thickness also caused changes in the composition of the plume melts (Regelous et al., 2002). We will complement these previous studies and the ongoing work of the other Leg 197 scientists by studying two aspects of the Emperor seamount basalts: helium isotopes and melt inclusion compositions. We will measure the helium isotopic ratios of selected olivine separates from three of the Leg 197 drill sites and from DSDP Site 433 on Suiko seamount (65 Ma) to determine if the composition of the Hawaiian "plume signal" has changed over time. We will also analyze the major and trace element compositions of melt inclusions that were isolated from shallow-level magma mixing and crystal fractionation processes to determine how much of the geochemical variations observed in the Emperor basalts are due to changes in melting processes. All of the drill sites recovered olivine and plagioclase phenocrysts suitable for melt inclusion studies.

Validating predictions made by a thermo-mechanical model of melt segregation in sub-volcanic systems

NASA Astrophysics Data System (ADS)

Roele, Katarina; Jackson, Matthew; Morgan, Joanna

2014-05-01

A quantitative understanding of the spatial and temporal evolution of melt distribution in the crust is crucial in providing insights into the development of sub-volcanic crustal stratigraphy and composition. This work aims to relate numerical models that describe the base of volcanic systems with geophysical observations. Recent modelling has shown that the repetitive emplacement of mantle-derived basaltic sills, at the base of the lower crust, acts as a heat source for anatectic melt generation, buoyancy-driven melt segregation and mobilisation. These processes form the lowermost architecture of complex sub-volcanic networks as upward migrating melt produces high melt fraction layers. These 'porosity waves' are separated by zones with high compaction rates and have distinctive polybaric chemical signatures that suggest mixed crust and mantle origins. A thermo-mechanical model produced by Solano et al in 2012 has been used to predict the temperatures and melt fractions of successive high porosity layers within the crust. This model was used as it accounts for the dynamic evolution of melt during segregation and migration through the crust; a significant process that has been neglected in previous models. The results were used to input starting compositions for each of the layers into the rhyolite-MELTS thermodynamic simulation. MELTS then determined the approximate bulk composition of the layers once they had cooled and solidified. The mean seismic wave velocities of the polymineralic layers were then calculated using the relevant Voight-Reuss-Hill mixture rules, whilst accounting for the pressure and temperature dependence of seismic wave velocity. The predicted results were then compared with real examples of reflectivity for areas including the UK, where lower crustal layering is observed. A comparison between the impedance contrasts at compositional boundaries is presented as it confirms the extent to which modelling is able to make predictions that are consistent with the real data. This highlights improvements that could be made to the thermo-mechanical model, such as an extension into 3-D that would be capable of capturing the effects of convective instabilities. In addition, it describes how far numerical models are capable of reducing the uncertainty in the parameter space for poorly defined crustal properties. Most importantly however, it gives an improved understanding of the intrusion and development of melt zones in the continental crust that ultimately control the formation of volcanic systems. [1] Solano, J. M. S., M. D. Jackson, R. S. J. Sparks, J. D. Blundy, and C. Annen (2012). Melt segregation in deep crustal hot zones: a mechanism for chemical differentiation, crustal assimilation and the formation of evolved magmas. Journal of Petrology, 53, Number 10, Pages 1999-2026. DOI: 10.1093/petrology/egs041.

Recent advances in the study of the UO2-PuO2 phase diagram at high temperatures

NASA Astrophysics Data System (ADS)

Böhler, R.; Welland, M. J.; Prieur, D.; Cakir, P.; Vitova, T.; Pruessmann, T.; Pidchenko, I.; Hennig, C.; Guéneau, C.; Konings, R. J. M.; Manara, D.

2014-05-01

Recently, novel container-less laser heating experimental data have been published on the melting behaviour of pure PuO2 and PuO2-rich compositions in the uranium dioxide-plutonium dioxide system. Such data showed that previous data obtained by more traditional furnace heating techniques were affected by extensive interaction between the sample and its containment. It is therefore paramount to check whether data so far used by nuclear engineers for the uranium-rich side of the pseudo-binary dioxide system can be confirmed or not. In the present work, new data are presented both in the UO2-rich part of the phase diagram, most interesting for the uranium-plutonium dioxide based nuclear fuel safety, and in the PuO2 side. The new results confirm earlier furnace heating data in the uranium-dioxide rich part of the phase diagram, and more recent laser-heating data in the plutonium-dioxide side of the system. As a consequence, it is also confirmed that a minimum melting point must exist in the UO2-PuO2 system, at a composition between x(PuO2) = 0.4 and x(PuO2) = 0.7 and 2900 K ⩽ T ⩽ 3000 K. Taking into account that, especially at high temperature, oxygen chemistry has an effect on the reported phase boundary uncertainties, the current results should be projected in the ternary U-Pu-O system. This aspect has been extensively studied here by X-ray diffraction and X-ray absorption spectroscopy. The current results suggest that uncertainty bands related to oxygen behaviour in the equilibria between condensed phases and gas should not significantly affect the qualitative trend of the current solid-liquid phase boundaries.

Dynamic melting in plume heads: the formation of Gorgona komatiites and basalts

NASA Astrophysics Data System (ADS)

Arndt, Nicholas T.; Kerr, Andrew C.; Tarney, John

1997-01-01

The small Pacific island of Gorgona, off the coast of Colombia, is well known for its spectacular spinifex-textured komatiites. These high-Mg liquids, which have been linked to a late Cretaceous deep mantle plume, are part of a volcanic series with a wide range of trace-element compositions, from moderately enriched basalts ( La/SmN ˜ 1.5) to extremely depleted ultramafic tuffs and picrites ( La/SmN ˜ 0.2). Neither fractional crystallization, nor partial melting of a homogeneous mantle source, can account for this large variation: the source must have been chemically heterogeneous. Low 143Nd/144Nd in the more enriched basalts indicates some initial source heterogeneity but most of the variation in magma compositions is believed to result from dynamic melting during the ascent of a plume. Modelling of major- and trace-element compositions suggests that ultramafic magmas formed at ˜ 60-100 km depth, and that the melt extraction that gave rise to their depleted sources started at still greater depths. The ultra-depleted lavas represent magmas derived directly from the hottest, most depleted parts of the plume; the more abundant moderately depleted basalts are interpreted as the products of pooling of liquids from throughout the melting region.

Chelyabinsk meteorite explains unusual spectral properties of Baptistina Asteroid Family

NASA Astrophysics Data System (ADS)

Reddy, Vishnu; Sanchez, Juan A.; Bottke, William F.; Cloutis, Edward A.; Izawa, Matthew R. M.; O'Brien, David P.; Mann, Paul; Cuddy, Matthew; Le Corre, Lucille; Gaffey, Michael J.; Fujihara, Gary

2014-07-01

We investigated the spectral and compositional properties of Chelyabinsk meteorite to identify its possible parent body in the main asteroid belt. Our analysis shows that the meteorite contains two spectrally distinct but compositionally indistinguishable components of LL5 chondrite and shock blackened/impact melt material. Our X-ray diffraction analysis confirms that the two lithologies of the Chelyabinsk meteorite are extremely similar in modal mineralogy. The meteorite is compositionally similar to LL chondrite and its most probable parent asteroid in the main belt is a member of the Flora family. Our work confirms previous studies (e.g., Vernazza et al. [2008]. Nature 454, 858-860; de León, J., Licandro, J., Serra-Ricart, M., Pinilla-Alonso, N., Campins, H. [2010]. Astron. Astrophys. 517, A23; Dunn, T.L., Burbine, T.H., Bottke, W.F., Clark, J.P. [2013]. Icarus 222, 273-282), linking LL chondrites to the Flora family. Intimate mixture of LL5 chondrite and shock blackened/impact melt material from Chelyabinsk provides a spectral match with (8) Flora, the largest asteroid in the Flora family. The Baptistina family and Flora family overlap each other in dynamical space. Mineralogical analysis of (298) Baptistina and 11 small family members shows that their surface compositions are similar to LL chondrites, although their absorption bands are subdued and albedos lower when compared to typical S-type asteroids. A range of intimate mixtures of LL5 chondrite and shock blackened/impact melt material from Chelyabinsk provides spectral matches for all these BAF members. We suggest that the presence of a significant shock/impact melt component in the surface regolith of BAF members could be the cause of lower albedo and subdued absorption bands. The conceptual problem with part of this scenario is that impact melts are very rare within ordinary chondrites. Of the ∼42,000 ordinary chondrites, less than 0.5% (203) of them contain impact melts. A major reason that impact melts are rare in meteorites is that high impact velocities (V > 10 km/s) are needed to generate the necessary shock pressures and temperatures (e.g., Pierazzo, E., Melosh, H.J. [1998]. Hydrocode modeling of oblique impacts: The fate of the projectile. In: Origin of the Earth and Moon, Proceedings of the Conference. LPI Contribution No. 957) unless the target material is highly porous. Nearly all asteroid impacts within the main belt are at ∼5 km/s (Bottke, W.F., Nolan, M.C., Greenberg, R., Kolvoord, R.A. [1994]. Collisional lifetimes and impact statistics of near-Earth asteroids. In: Tucson, Gehrels T. (Ed.), Hazards Due to Comets and Asteroids. The University of Arizona Press, Arizona, pp. 337-357), which prevents them from producing much impact melt unless they are highly porous. However, shock darkening is an equally efficient process that takes place at much lower impact velocities (∼2 km/s) and can cause the observed spectral effects. Spectral effects of shock darkening and impact melt are identical. The parent asteroid of BAF was either a member of the Flora family or had the same basic composition as the Floras (LL Chondrite). The shock pressures produced during the impact event generated enough impact melt or shock blackening to alter the spectral properties of BAF, but keep the BAF composition largely unchanged. Collisional mixing of shock blackened/impact melt and LL5 chondritic material could have created the Baptistina Asteroid Family with composition identical to those of the Floras, but with subdued absorption bands. Shock darkening and impact melt play an important role in altering the spectral and albedo properties of ordinary chondrites and our work confirms earlier work by Britt and Pieters (Britt, D.T., Pieters, C.M. [1994]. Geochimica et Cosmochimica Acta 58, 3905-3919).

Solidification observations and sliding wear behavior of vacuum arc melting processed Ni-Al-TiC composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karantzalis, A.E., E-mail: akarantz@cc.uoi.gr; Lekatou, A.; Tsirka, K.

2012-07-15

Monolithic Ni{sub 3}Al and Ni-25 at.%Al intermetallic matrix TiC-reinforced composites were successfully produced by vacuum arc melting. TiC crystals were formed through a dissolution-reprecipitation mechanism and their final morphology is explained by means of a) Jackson's classical nucleation and growth phenomena and b) solidification rate considerations. The TiC presence altered the matrix microconstituents most likely due to specific melt-particle interactions and crystal plane epitaxial matching. TiC particles caused a significant decrease on the specific wear rate of the monolithic Ni{sub 3}Al alloy and the possible wear mechanisms are approached by means of a) surface oxidation, b) crack/flaws formation, c) materialmore » detachment and d) debris-counter surfaces interactions. - Highlights: Black-Right-Pointing-Pointer Vacuum arc melting (VAM) of Ni-Al based intermetallic matrix composite materials. Black-Right-Pointing-Pointer Solidification phenomena examination. Black-Right-Pointing-Pointer TiC crystal formation and growth mechanisms. Black-Right-Pointing-Pointer Sliding wear examination.« less

Theoretical calculation of the melting curve of Cu-Zr binary alloys

DOE PAGES

Gunawardana, K. G.S.H.; Wilson, S. R.; Mendelev, M. I.; ...

2014-11-14

Helmholtz free energies of the dominant binary crystalline solids found in the Cu-Zr system at high temperatures close to the melting curve are calculated. This theoretical approach combines fundamental measure density functional theory (applied to the hard-sphere reference system) and a perturbative approach to include the attractive interactions. The studied crystalline solids are Cu(fcc), Cu 51Zr 14(β), CuZr(B 2), CuZr 2(C11b), Zr(hcp), and Zr(bcc). The calculated Helmholtz free energies of crystalline solids are in good agreement with results from molecular-dynamics (MD) simulations. Using the same perturbation approach, the liquid phase free energies are calculated as a function of composition andmore » temperature, from which the melting curve of the entire composition range of this system can be obtained. Phase diagrams are determined in this way for two leading embedded atom method potentials, and the results are compared with experimental data. Furthermore, theoretical melting temperatures are compared both with experimental values and with values obtained directly from MD simulations at several compositions.« less

Melt inclusion evidence for a volatile-enriched (H2O, Cl, B) component in parental magmas of Gorgona Island komatiites

NASA Astrophysics Data System (ADS)

Kamenetsky, V.; Sobolev, A.; McDonough, W.

2003-04-01

Late Cretaceous komatiites of Gorgona Island are unambiguous samples of ultra-mafic melts related to a hot and possibly 'wet' mantle plume. Despite significant efforts in studying komatiites, their volatile abundances remain largely unknown because of significant alteration of rocks and lack of fresh glasses. This work presents major, trace and volatile element data for 22 partially homogenised (at 1275oC and 1 bar pressure) melt inclusions in olivine (Fo 90.5-91.5) from a Gorgona Isl. komatiite (# Gor 94-3). Major element compositions (except FeO which is notably lower by up to 5 wt% as a result of post-entrapment re-equilibration) and most lithophile trace elements of melt inclusions are indistinguishable from the whole rock komatiites. With the exception of three inclusions that have low Na, H2O, Cl, F and S (likely compromised and degassed during heating) most compositions are characterised by relatively constant and high volatile abundances (H2O 0.4-0.8 wt%, Cl 0.02-0.03 wt%, B 0.8-1.4 ppm). These are interpreted as representative of original volatiles in parental melts because they correspond to the internal volatile pressure in the closed inclusions significantly exceeding 1 bar pressure of heating experiment. Although H2O is strongly enriched (PM-normalised H2O/Ce 10-17) its concentrations correlate well with many elements (e.g. Yb, Er, Y, Ti, Sr, Be). Other positive anomalies on the overall depleted (La/Sm 0.26-0.33) PM normalized compositional spectra of melt inclusions are shown by B (B/K 2.4-5.4) and Cl (Cl/K 11-16). Compositions of melt inclusions, when corrected for Fe loss and recalculated in equilibrium with host olivine, have high MgO (15.4-16.4 wt%; Mg# of 74) and substantial H2O (0.4-0.6 wt%) contents. This together with the data on other 'enriched' elements argues for the presence of previously unknown volatile-enriched component in the parental melts of Gorgona Isl. komatiites. We discuss contamination of magmas by altered oceanic crust in the plumbing system, the involvement of volatile-rich subduction related component(s) in the mantle source, and the geochemical control from residual garnet during the generation of komatiite primary melts.

Low-melting point heat transfer fluid

DOEpatents

Cordaro, Joseph Gabriel; Bradshaw, Robert W.

2010-11-09

A low-melting point, heat transfer fluid made of a mixture of five inorganic salts including about 29.1-33.5 mol % LiNO.sub.3, 0-3.9 mol % NaNO.sub.3, 2.4-8.2 mol % KNO.sub.3, 18.6-19.9 mol % NaNO.sub.2, and 40-45.6 mol % KNO.sub.2. These compositions can have liquidus temperatures below 80.degree. C. for some compositions.

Generation of trondhjemite from partial melting of dacite under granulite facies conditions: an example from the New Jersey Highlands, USA

USGS Publications Warehouse

Puffer, J.H.; Volkert, R.A.

1991-01-01

New field and geochemical data place the Losee Metamorphic Suite (a tonalite/trondhjemite complex) of northern New Jersey into the context of a major Proterozoic continental are represented by a discontinuous belt of northern Appalachian metadacite. Samples of Losee rock range from extremely leucocratic trondhjemite locally associated with amphibolite, to banded biotite, hornblende, pyroxene, and garnet-bearing tonalites. The major element and REE composition of the tonalite closely resembles dacite from continental are settings and model melts extracted from an eclogite residue by partial melting at 15 kbar. The REE composition of most Losee trondhjemite is enriched in REE, particularly HREE, compared with Losee tonalite, and is interpreted as the product of local anatectic melting of Losee tonalite (metadacite) that occurred in a granulite facies environment during the Grenville orogeny. ?? 1991.

Space- and Ground-Based Crystal Growth Using a Baffle (CGB)

NASA Technical Reports Server (NTRS)

Ostrogorsky, A. G.; Marin, C.; Peignier, T.; Duffar, T.; Volz, M.; Jeter, L.; Luz, P.

2001-01-01

The composition of semiconductor crystals produced in space by conventional melt-growth processes (directional solidification and zone melting) is affected by minute levels of residual micro-acceleration, which causes natural convection. The residual acceleration has random magnitude, direction and frequency. Therefore, the velocity field in the melt is apriori unpredictable. As a result, the composition of the crystals grown in space can not be predicted and reproduced. The method for directional solidification with a submerged heater or a baffle was developed under NASA sponsorship. The disk-shaped baffle acts as a partition, creating a small melt zone at the solid-liquid interface. As a result, in ground based experiment the level of buoyancy-driven convection at the interface is significantly reduced. In several experiments with Te-doped GaSb, nearly diffusion controlled segregation was achieved.

Method for melting glass by measurement of non-bridging oxygen

DOEpatents

Jantzen, Carol M.

1992-01-01

A method for making better quality molten glass in a glass melter, the glass having the desired viscosity and, preferably, also the desired resistivity so that the glass melt can be established effectively and the product of the glass melter will have the desired level of quality. The method includes the adjustment of the composition of the glass constituents that are fed into the melter in accordance with certain correlations that reliably predict the viscosity and resistivity from the melter temperature and the melt composition, then heating the ingredients to the melter's operating temperature until they melt and homogenize. The equations include the calculation of a "non-bridging oxygen" term from the numbers of moles of the various ingredients, and then the determination of the viscosity and resistivity from the operating temperature of the melter and the non-bridging oxygen term.

Studies on the reactive melt infiltration of silicon and silicon-molybdenum alloys in porous carbon

NASA Technical Reports Server (NTRS)

Singh, M.; Behrendt, D. R.

1992-01-01

Investigations on the reactive melt infiltration of silicon and silicon-1.7 and 3.2 at percent molybdenum alloys into porous carbon preforms have been carried out by process modeling, differential thermal analysis (DTA) and melt infiltration experiments. These results indicate that the initial pore volume fraction of the porous carbon preform is a critical parameter in determining the final composition of the raction-formed silicon carbide and other residual phases. The pore size of the carbon preform is very detrimental to the exotherm temperatures due to liquid silicon-carbon reactions encountered during the reactive melt infiltration process. A possible mechanism for the liquid silicon-porous (glassy) carbon reaction has been proposed. The composition and microstructure of the reaction-formed silicon carbide has been discussed in terms of carbon preform microstructures, infiltration materials, and temperatures.

Concentrations and behavior of oxygen and oxide ion in melts of composition CaO.MgO.xSiO2

NASA Technical Reports Server (NTRS)

Semkow, K. W.; Haskin, L. A.

1985-01-01

The behavior of oxygen and oxide ion in silicate melts was investigated through their electrochemical reactions at a platinum electrode. Values are given for the diffusion coefficient for molecular oxygen in diopside melt and the activation energy of diffusion. It is shown that molecular oxygen dissociates prior to undergoing reduction and that oxide ion reacts quickly with silicate polymers when it is produced. The concentration of oxide ion is kept low by a buffering effect of the silicate, the exact level being dependent on the silicate composition. Data on the kinetics of reaction of the dissociation of molecular oxygen and on the buffering reactions are provided. It is demonstrated that the data on oxygen in these silicate melts are consistent with those for solid buffers.

Petrogenesis of Miller Range 07273, a new type of anomalous melt breccia: Implications for impact effects on the H chondrite asteroid

NASA Astrophysics Data System (ADS)

Ruzicka, Alex M.; Hutson, Melinda; Friedrich, Jon M.; Rivers, Mark L.; Weisberg, Michael K.; Ebel, Denton S.; Ziegler, Karen; Rumble, Douglas; Dolan, Alyssa A.

2017-09-01

Miller Range 07273 is a chondritic melt breccia that contains clasts of equilibrated ordinary chondrite set in a fine-grained (<5 μm), largely crystalline, igneous matrix. Data indicate that MIL was derived from the H chondrite parent asteroid, although it has an oxygen isotope composition that approaches but falls outside of the established H group. MIL also is distinctive in having low porosity, cone-like shapes for coarse metal grains, unusual internal textures and compositions for coarse metal, a matrix composed chiefly of clinoenstatite and omphacitic pigeonite, and troilite veining most common in coarse olivine and orthopyroxene. These features can be explained by a model involving impact into a porous target that produced brief but intense heating at high pressure, a sudden pressure drop, and a slower drop in temperature. Olivine and orthopyroxene in chondrule clasts were the least melted and the most deformed, whereas matrix and troilite melted completely and crystallized to nearly strain-free minerals. Coarse metal was largely but incompletely liquefied, and matrix silicates formed by the breakdown during melting of albitic feldspar and some olivine to form pyroxene at high pressure (>3 GPa, possibly to 15-19 GPa) and temperature (>1350 °C, possibly to ≥2000 °C). The higher pressures and temperatures would have involved back-reaction of high-pressure polymorphs to pyroxene and olivine upon cooling. Silicates outside of melt matrix have compositions that were relatively unchanged owing to brief heating duration.

A hybrid composite dike suite from the northern Arabian Nubian Shield, southwest Jordan: Implications for magma mixing and partial melting of granite by mafic magma

NASA Astrophysics Data System (ADS)

Jarrar, Ghaleb H.; Yaseen, Najel; Theye, Thomas

2013-03-01

The Arabian Nubian Shield is an exemplary juvenile continental crust of Neoproterozoic age (1000-542 Ma). The post-collisional rift-related stage (~ 610 to 542 Ma) of its formation is characterized among others by the intrusion of several generations of simple and composite dikes. This study documents a suite of hybrid composite dikes and a natural example of partial melting of granite by a mafic magma from the northernmost extremity of Arabian Nubian Shield in southwest Jordan. The petrogenesis of this suite is discussed on the basis of field, petrographic, geochemical, and Rb/Sr isotopic data. These dikes give spectacular examples of the interaction between basaltic magma and the granitic basement. This interaction ranges from brecciation, partial melting of the host alkali feldspar granite to complete assimilation of the granitic material. Field structures range from intrusive breccia (angular partially melted granitic fragments in a mafic groundmass) to the formation of hybrid composite dikes that are up to 14 m in thickness. The rims of these dikes are trachyandesite (latite) with alkali feldspar ovoids (up to 1 cm in diameter); while the central cores are trachydacite to dacite and again with alkali feldspar ovoids and xenoliths from the dike rims. The granitic xenoliths in the intrusive breccia have been subjected to at least 33% partial melting. A seven-point Rb/Sr isochron from one of these composite dikes yields an age of 561 ± 33 Ma and an initial 87Sr/86Sr ratio of 0.70326 ± 0.0003 (2σ) and MSWD of 0.62. Geochemical modeling using major, trace, rare earth elements and isotopes suggests the generation of the hybrid composite dike suite through the assimilation of 30% to 60% granitic crustal material by a basaltic magma, while the latter was undergoing fractional crystallization at different levels in the continental crust.

Experimental calibration of a new oxybarometer for silicic magmas based on the partitioning of vanadium between magnetite and silicate melt

NASA Astrophysics Data System (ADS)

Arató, Róbert; Audétat, Andreas

2016-04-01

Oxygen fugacity is an important parameter in magmatic systems that affects the stability of mineral phases and fluid species. However, there is no well-established method to reconstruct the oxygen fugacity of slowly cooled magmas such as granite, for example, because existing oxybarometers (e.g., magnetite-ilmenite method) are susceptible to re-equilibration processes during slow cooling and thus lead to erroneous results when applied for granitic rocks. In this study, we aim at developing an oxybarometer that is based on the partitioning of vanadium (a redox-sensitive element) between magnetite inclusions and silicate melt inclusions preserved in quartz phenocrysts, where they were protected from subsolidus alteration and can be measured as entities by LA-ICP-MS. In the first - experimental - part of this study we investigated the effects of temperature (800-950 ° C), pressure (1-2 kbar), oxygen fugacity (from ΔFMQ+0.7 to ΔFMQ+4.0), magnetite composition, and melt composition on the partition coefficient of vanadium between magnetite and melt (DVmgt-melt). The experiments were carried out in cold-seal pressure vessels and the starting material was a mixture of V-doped haplogranite glasses or natural obsidian powder with variable aluminum saturation index (ASI), and synthetic, V-free magnetite of 10-20 μm grain size. The vanadium partition coefficient was found to depend strongly on oxygen fugacity, and to lesser (but still considerable) degrees on melt composition and temperature. A more than 1.5 log unit decrease in DVmgt-melt values with increasing oxygen fugacity can be explained by a change of the dominant valence state of V in the silicate melt. For a given oxygen fugacity buffer DVmgt-melt decreases with increasing temperature, but this reflects mostly the change in absolute fO2 values while the net temperature effect is in fact positive. DVmgt-melt depends significantly on melt composition, resulting in higher D-values with increasing aluminum saturation index (ASI). This seems to reflect less favorable incorporation of V into peraluminous melts compared to depolymerized, peralkaline melts. Changing pressure from 1 to 2 kbar had an effect only at NNO, causing 0.3 log unit increase in D, whereas the Ti-content of magnetite turned out to have negligible effect on the V partitioning. In summary, the dependence of DVmgt-melt on temperature, ASI and oxygen fugacity can be described by the following regression equation: logD(V)mgt/melt=-1.22+0.31*10^5/T(° K) +1.73*ASI -0.49*ΔFMQ First tests of the equation on natural samples were carried out on rapidly cooled tuffs and vitrophyres from variable tectonic settings, for which fO2 could be constrained independently by the magnetite-ilmenite method. All calculated fO2 values fall within ± 0.75 log unit within those suggested by the Fe-Ti oxybarometer, whereas 12 out of 16 samples agree within 0.5 log units .

Toward a coherent model for the melting behavior of the deep Earth's mantle

NASA Astrophysics Data System (ADS)

Andrault, D.; Bolfan-Casanova, N.; Bouhifd, M. A.; Boujibar, A.; Garbarino, G.; Manthilake, G.; Mezouar, M.; Monteux, J.; Parisiades, P.; Pesce, G.

2017-04-01

Knowledge of melting properties is critical to predict the nature and the fate of melts produced in the deep mantle. Early in the Earth's history, melting properties controlled the magma ocean crystallization, which potentially induced chemical segregation in distinct reservoirs. Today, partial melting most probably occurs in the lowermost mantle as well as at mid upper-mantle depths, which control important aspects of mantle dynamics, including some types of volcanism. Unfortunately, despite major experimental and theoretical efforts, major controversies remain about several aspects of mantle melting. For example, the liquidus of the mantle was reported (for peridotitic or chondritic-type composition) with a temperature difference of ∼1000 K at high mantle depths. Also, the Fe partitioning coefficient (DFeBg/melt) between bridgmanite (Bg, the major lower mantle mineral) and a melt was reported between ∼0.1 and ∼0.5, for a mantle depth of ∼2000 km. Until now, these uncertainties had prevented the construction of a coherent picture of the melting behavior of the deep mantle. In this article, we perform a critical review of previous works and develop a coherent, semi-quantitative, model. We first address the melting curve of Bg with the help of original experimental measurements, which yields a constraint on the volume change upon melting (ΔVm). Secondly, we apply a basic thermodynamical approach to discuss the melting behavior of mineralogical assemblages made of fractions of Bg, CaSiO3-perovskite and (Mg,Fe)O-ferropericlase. Our analysis yields quantitative constraints on the SiO2-content in the pseudo-eutectic melt and the degree of partial melting (F) as a function of pressure, temperature and mantle composition; For examples, we find that F could be more than 40% at the solidus temperature, except if the presence of volatile elements induces incipient melting. We then discuss the melt buoyancy in a partial molten lower mantle as a function of pressure, F and DFeBg/melt. In the lower mantle, density inversions (i.e. sinking melts) appear to be restricted to low F values and highest mantle pressures. The coherent melting model has direct geophysical implications: (i) in the early Earth, the magma ocean crystallization could not occur for a core temperature higher than ∼5400 K at the core-mantle boundary (CMB). This temperature corresponds to the melting of pure Bg at 135 GPa. For a mantle composition more realistic than pure Bg, the right CMB temperature for magma ocean crystallization could have been as low as ∼4400 K. (ii) There are converging arguments for the formation of a relatively homogeneous mantle after magma ocean crystallization. In particular, we predict the bulk crystallization of a relatively large mantle fraction, when the temperature becomes lower than the pseudo-eutectic temperature. Some chemical segregation could still be possible as a result of some Bg segregation in the lowermost mantle during the first stage of the magma ocean crystallization, and due to a much later descent of very low F, Fe-enriched, melts toward the CMB. (iii) The descent of such melts could still take place today. There formation should to be related to incipient mantle melting due to the presence of volatile elements. Even though, these melts can only be denser than the mantle (at high mantle depths) if the controversial value of DFeBg/melt is indeed as low as suggested by some experimental studies. This type of melts could contribute to produce ultra-low seismic velocity anomalies in the lowermost mantle.

Petrogenesis of siliceous high-Mg series rocks as exemplified by the Early Paleoproterozoic mafic volcanic rocks of the Eastern Baltic Shield: enriched mantle versus crustal contamination

NASA Astrophysics Data System (ADS)

Bogina, Maria; Zlobin, Valeriy; Sharkov, Evgenii; Chistyakov, Alexeii

2015-04-01

The Early Paleoproterozoic stage in the Earth's evolution was marked by the initiation of global rift systems, the tectonic nature of which was determined by plume geodynamics. These processes caused the voluminous emplacement of mantle melts with the formation of dike swarms, mafic-ultramafic layered intrusions, and volcanic rocks. All these rocks are usually considered as derivatives of SHMS (siliceous high-magnesian series). Within the Eastern Baltic Shield, the SHMS volcanic rocks are localized in the domains with different crustal history: in the Vodlozero block of the Karelian craton with the oldest (Middle Archean) crust, in the Central Block of the same craton with the Neoarchean crust, and in the Kola Craton with a heterogeneous crust. At the same time, these rocks are characterized by sufficiently close geochemical characteristics: high REE fractionation ((La/Yb)N = 4.9-11.7, (La/Sm)N=2.3-3.6, (Gd/Yb)N =1.66-2.74)), LILE enrichment, negative Nb anomaly, low to moderate Ti content, and sufficiently narrow variations in Nd isotope composition from -2.0 to -0.4 epsilon units. The tectonomagmatic interpretation of these rocks was ambiguous, because such characteristics may be produced by both crustal contamination of depleted mantle melts, and by generation from a mantle source metasomatized during previous subduction event. Similar REE patterns and overlapping Nd isotope compositions indicate that the studied basaltic rocks were formed from similar sources. If crustal contamination en route to the surface would play a significant role in the formation of the studied basalts, then almost equal amounts of contaminant of similar composition are required to produce the mafic rocks with similar geochemical signatures and close Nd isotopic compositions, which is hardly possible for the rocks spaced far apart in a heterogeneous crust. This conclusion is consistent with analysis of some relations between incompatible elements and their ratios. In particular, the rocks show no correlation between Th/Ta and La/Yb, (Nb/La)pm ratio and Th content, and eNd and (Nb/La)N ratio. At the same time, some correlation observed in the eNd-Mg# and (La/Sm)N-(Nb/La)N diagrams in combination with the presence of inherited zircons in the rocks does not allow us to discard completely the crustal contamination. Examination of Sm/Yb-La/Sm relations and the comparison with model melting curves for garnet and spinel lherzolites showed that the parental melts of the rocks were derived by 10-30% mantle melting at garnet-spinel facies transition. Two stage model can be proposed to explain such remarkable isotope-geochemical homogeneity of the mafic volcanic rocks over a large area: (1) ubiquitous emplacement of large volumes of sanukitoid melts in the lower crust of the shield at 2.7 Ga; (2) underplating of plume-derived DM melts at the crust-mantle boundary, melting of the lower crust of sanukitoid composition, and subsequent mixing of these melts with formation of SHMS melts at 2.4 Ga. A simple mixing model showed that in this case the Nd isotope composition of obtained melts remained practically unchanged at variable amounts of contaminant (up to 30%). This work was supported by the RFBR no. 14-05-00458.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newell, J; Miller, D; Stone, M

The Savannah River National Laboratory (SRNL) was tasked to provide an assessment of the downstream impacts to the Defense Waste Processing Facility (DWPF) of decisions regarding the implementation of Al-dissolution to support sludge mass reduction and processing. Based on future sludge batch compositional projections from the Liquid Waste Organization's (LWO) sludge batch plan, assessments have been made with respect to the ability to maintain comparable projected operating windows for sludges with and without Al-dissolution. As part of that previous assessment, candidate frits were identified to provide insight into melt rate for average sludge batches representing with and without Al-dissolution flowsheets.more » Initial melt rate studies using the melt rate furnace (MRF) were performed using five frits each for Cluster 2 and Cluster 4 compositions representing average without and with Al-dissolution. It was determined, however, that the REDOX endpoint (Fe{sup 2+}/{Sigma}Fe for the glass) for Clusters 2 and 4 resulted in an overly oxidized feed which negatively affected the initial melt rate tests. After the sludge was adjusted to a more reduced state, additional testing was performed with frits that contained both high and low concentrations of sodium and boron oxides. These frits were selected strictly based on the ability to ascertain compositional trends in melt rate and did not necessarily apply to any acceptability criteria for DWPF processing. The melt rate data are in general agreement with historical trends observed at SRNL and during processing of SB3 (Sludge Batch 3)and SB4 in DWPF. When MAR acceptability criteria were applied, Frit 510 was seen to have the highest melt rate at 0.67 in/hr for Cluster 2 (without Al-dissolution), which is compositionally similar to SB4. For Cluster 4 (with Al-dissolution), which is compositionally similar to SB3, Frit 418 had the highest melt rate at 0.63 in/hr. Based on this data, there appears to be a slight advantage of the Frit 510 based system without Al-dissolution relative to the Frit 418 based system with Al-dissolution. Though the without aluminum dissolution scenario suggests a slightly higher melt rate with frit 510, several points must be taken into consideration: (1) The MRF does not have the ability to assess liquid feeds and, thus, rheology impacts. Instead, the MRF is a 'static' test bed in which a mass of dried melter feed (SRAT product plus frit) is placed in an 'isothermal' furnace for a period of time to assess melt rate. These conditions, although historically effective in terms of identifying candidate frits for specific sludge batches and mapping out melt rate versus waste loading trends, do not allow for assessments of the potential impact of feed rheology on melt rate. That is, if the rheological properties of the slurried melter feed resulted in the mounding of the feed in the melter (i.e., the melter feed was thick and did not flow across the cold cap), melt rate and/or melter operations (i.e., surges) could be negatively impacted. This could affect one or both flowsheets. (2) Waste throughput factors were not determined for Frit 510 and Frit 418 over multiple waste loadings. In order to provide insight into the mission life versus canister count question, one needs to define the maximum waste throughput for both flowsheets. Due to funding limitations, the melt rate testing only evaluated melt rate at a fixed waste loading. (3) DWPF will be processing SB5 through their facility in mid-November 2008. Insight into the over arching questions of melt rate, waste throughput, and mission life can be obtained directly from the facility. It is recommended that processing of SB5 through the facility be monitored closely and that data be used as input into the decision making process on whether to implement Al-dissolution for future sludge batches.« less

Silicate glasses and sulfide melts in the ICDP-USGS Eyreville B core, Chesapeake Bay impact structure, Virginia, USA

USGS Publications Warehouse

Belkin, H.E.; Horton, J. Wright

2009-01-01

Optical and electron-beam petrography of melt-rich suevite and melt-rock clasts from selected samples from the Eyreville B core, Chesapeake Bay impact structure, reveal a variety of silicate glasses and coexisting sulfur-rich melts, now quenched to various sulfi de minerals (??iron). The glasses show a wide variety of textures, fl ow banding, compositions, devitrifi cation, and hydration states. Electron-microprobe analyses yield a compositional range of glasses from high SiO2 (>90 wt%) through a range of lower SiO2 (55-75 wt%) with no relationship to depth of sample. Some samples show spherical globules of different composition with sharp menisci, suggesting immiscibility at the time of quenching. Isotropic globules of higher interfacial tension glass (64 wt% SiO2) are in sharp contact with lower-surface-tension, high-silica glass (95 wt% SiO2). Immiscible glass-pair composition relationships show that the immiscibility is not stable and probably represents incomplete mixing. Devitrifi cation varies and some low-silica, high-iron glasses appear to have formed Fe-rich smectite; other glass compositions have formed rapid quench textures of corundum, orthopyroxene, clinopyroxene, magnetite, K-feldspar, plagioclase, chrome-spinel, and hercynite. Hydration (H2O by difference) varies from ~10 wt% to essentially anhydrous; high-SiO2 glasses tend to contain less H2O. Petrographic relationships show decomposition of pyrite and melting of pyrrhotite through the transformation series; pyrite? pyrrhotite? troilite??? iron. Spheres (~1 to ~50 ??m) of quenched immiscible sulfi de melt in silicate glass show a range of compositions and include phases such as pentlandite, chalcopyrite, Ni-As, monosulfi de solid solution, troilite, and rare Ni-Fe. Other sulfi de spheres contain small blebs of pure iron and exhibit a continuum with increasing iron content to spheres that consist of pure iron with small, remnant blebs of Fe-sulfi de. The Ni-rich sulfi de phases can be explained by melting and/or concentrating targetderived Ni without requiring an asteroid impactor source component. The presence of locally unaltered glasses in these rocks suggests that in some rock volumes, isolation from postimpact hydrothermal systems was suffi cient for glass preservation. Pressure and temperature indicators suggest that, on a thin-section scale, the suevites record rapid mixing and accumulation of particles that sustained widely different peak temperatures, from clasts that never exceeded 300 ?? 50 ??C, to the bulk of the glasses where melted sulfi de and unmelted monazite suggest temperatures of 1500 ?? 200 ??C. The presence of coesite in some glass-bearing samples suggests that pressures exceeded ~3 GPa. ?? 2009 Geological Society of America.

The Cr Redox Record of fO2 Variation in Angrites. Evidence for Redox Conditions of Angrite Petrogenesis and Parent Body

NASA Technical Reports Server (NTRS)

Shearer, Charles K.; Bell, Aaron S.; Burger, Paul V.; Papike, James J.; Jones, John; Le, Loan

2016-01-01

Angrites represent some of the earliest stages of planetesimal differentiation. Not surprisingly, there is no simple petrogenetic model for their origin. Petrogenesis has been linked to both magmatic and impact processes. Studies demonstrated that melting of chondritic material (e.g. CM, CV) at redox conditions where pure iron metal is unstable (e.g., IW+1 to IW+2) produced angrite-like melts. Alternatively, angrites were produced at more reducing conditions (

Primitive Melt Inclusions from Multiple Samples from the FAMOUS Zone: Insights into the Mantle Melting Column and the Fractionation Processes

NASA Astrophysics Data System (ADS)

Laubier, M.; Langmuir, C. H.

2008-12-01

On mid-ocean ridges, the influential work by Sobolev and Shimizu (Nature, 1993) and Sobolev (Petrology, 1996) has inferred fractional melting during polybaric upwelling by showing that olivine-hosted inclusions were formed over a range of pressures. However melt inclusion studies have often concerned single MORB samples and may be seen as anecdotal in the sense that they are neither repeated nor globally verified. Recent modeling and experimental results also suggest the importance of post-entrapment processes for major and trace elements. This study presents major and trace element data in 300 olivine-hosted melt inclusions from 11 samples from the FAMOUS segment on the Mid-Atlantic Ridge. Published data from Shimizu (Phys. Earth Planet. Int., 1998) and Kamenetsky (EPSL, 1996; spinel-hosted inclusions) are also reported. In parallel, major and trace element measurements were performed in 150 glasses of the segment in order to have consistent datasets. Melt inclusions, trapped in olivine phenocrysts Mg#85-92, display complex trends in major element plots and can be divided into three groups. Group 1, the largest, is characterized by high MgO (9.4-13.4 wt.%), intermediate SiO2 and Al2O3 contents. Group 2 displays distinctively high Al2O3 (up to 18.4 wt.%), low SiO2 (as low as 46.5 wt.%) and high MgO (10.5-12.8 wt.%) contents, along with low CaO and variable TiO2, K2O and incompatible element concentrations. Group 3 consists of the melt inclusions trapped in less primitive olivines (Mg#<88.5) and displays higher SiO2, CaO and trace element contents. In the lava population, two groups can be distinguished. A small subset, that shares many features with the group 2 melt inclusions, displays high MgO and Al2O3 and low SiO2 and incompatible element contents. This type of lava - high-Al, low-Si and high-Mg - has been previously reported for various mid-ocean ridges (e.g., le Roux et al., Contrib. Min. Petrol., 2002; Eason and Sinton, EPSL, 2008). The second group plots along liquid lines of descent at low pressure starting from the compositions of the group 1 melt inclusions. Modeling of continuous polybaric melting and crystallization shows that the different inclusion groups are derived from melts formed at various pressures in the melting column (~12-6 kbar). After segregation from the mantle, the three batches of melts are fractionated at distinct pressures. The group 2 melt inclusions are consistent with the highest pressure of melt formation and a major role of cpx+olivine fractionation at high pressure (8 kbar), whereas group 3 results indicate the lowest pressure of extraction and entrapment (1kbar). An important observation is that high-Al, low-Si lavas contain melt inclusions from both the low-Si, high-Al group 2 and normal compositions (groups 1 and 3). These lavas can be reproduced by mixing between these two populations of inclusions, followed by some extent of differentiation. Therefore, this study shows that lavas represent averages of melts differentiated from the melt inclusions, and that the major element variability among inclusions can be explained by the combined effects of polybaric melting and crystallization at variable pressure. Trace element compositions of group 1 and 2 melt inclusions show large variations; incompatible element ratios (Ba/La, Rb/Nb, etc) suggest local source heterogeneity. Further modeling will be carried out in order to distinguish between the effects of partial melting and source composition.

Mutual interaction between high and low stereo-regularity components for crystallization and melting behaviors of polypropylene blend fibers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawai, Kouya; Takarada, Wataru; Kikutani, Takeshi, E-mail: kikutani.t.aa@m.titech.ac.jp

Crystallization and melting behaviors of blend fibers of two types of polypropylene (PP), i.e. high stereo-regularity/high molecular weight PP (HPP) and low stereo-regularity/low molecular weight PP (LPP), was investigated. Blend fibers consisting of various HPP/LPP compositions were prepared through the melt spinning process. Differential scanning calorimetry (DSC), temperature modulated DSC (TMDSC) and wide-angle X-ray diffraction (WAXD) analysis were applied for clarifying the crystallization and melting behaviors of individual components. In the DSC measurement of blend fibers with high LPP composition, continuous endothermic heat was detected between the melting peaks of LPP at around 40 °C and that of HPP atmore » around 160 °C. Such endothermic heat was more distinct for the blend fibers with higher LPP composition indicating that the melting of LPP in the heating process was hindered because of the presence of HPP crystals. On the other hand, heat of crystallization was detected at around 90 °C in the case of blend fibers with LPP content of 30 to 70 wt%, indicating that the crystallization of HPP component was taking place during the heating of as-spun blend fibers in the DSC measurement. Through the TMDSC analysis, re-organization of the crystalline structure through the simultaneous melting and re-crystallization was detected in the cases of HPP and blend fibers, whereas re-crystallization was not detected during the melting of LPP fibers. In the WAXD analysis during the heating of fibers, amount of a-form crystal was almost constant up to the melting in the case of single component HPP fibers, whereas there was a distinct increase of the intensity of crystalline reflections from around 100 °C, right after the melting of LPP in the case of blend fibers. These results suggested that the crystallization of HPP in the spinning process as well as during the conditioning process after spinning was hindered by the presence of LPP.« less

The Deep Crust Magmatic Refinery, Part 1: A Coupled Thermodynamic and Two-phase Flow Model

NASA Astrophysics Data System (ADS)

Riel, N., Jr.; Bouilhol, P.; Van Hunen, J.; Velic, M.; Magni, V.

2016-12-01

Metamorphic and magmatic processes occurring in the deep crust ultimately control the chemical and physical characteristic of the continental crust. A complex interplay between magma intrusion, crystallization, and reaction with the pre-existing crust provide a wide range of differentiated magma and cumulates (and / or restites) that will feed the upper crustal levels with evolved melt while constructing the lower crust. With growing evidence from field and experimental studies, it becomes clearer that crystallization and melting processes are non-exclusive but should be considered together. Incoming H2O bearing mantle melts will start to fractionate to a certain extent, forming cumulates but also releasing heat and H2O to the intruded host-rock allowing it to melt in saturated conditions. The end-result of such dynamic system is a function of the amount and composition of melt input, and extent of reaction with the host which is itself dependent on the migration mode of the melts. To assess the dynamics of this deep magmatic system we developed a new 2-D two-phase flow code using finite volume method. Our formulation takes into account: (i) melt flow through a viscous porous matrix with temperature- and melt-content dependent host-rock viscosity, (ii) heat transfer, assuming local thermal equilibrium between solid and liquid, (iii) thermodynamic modelling of stable phases, (iv) injection of fractionated melt from crystallizing basalt at the Moho and (v) chemical advection of both the solid and liquid compositions. Here we present the core of our modelling approach, especially the petrological implementation. We show in details that our thermodynamic model can reproduce well both the sub- and supra solidus phase relationship and composition of the host-rock. We apply our method to an idealized amphibolite lower crust that is affected by a magmatic event represented by the intrusion of a wet mantle melt into the crust at Moho depth. The models [see Bouilhol et al. associated abstract for results] allow calculating the different proportion of phases present in the system through time.

Investigation of molybdate melts as an alternative method of reprocessing used nuclear fuel

DOE PAGES

Hames, Amber L.; Tkac, Peter; Paulenova, Alena; ...

2017-01-17

Here, an investigation of molybdate melts containing sodium molybdate (Na 2MoO 4) and molybdenum trioxide (MoO 3) to achieve the separation of uranium from fission products by crystallization has been performed. The separation is based on the difference in solubility of the fission product metal oxides compared to the uranium oxide or molybdate in the molybdate melt. The molybdate melt dissolves uranium dioxide at high temperatures, and upon cooling, uranium precipitates as uranium dioxide or molybdate, whereas the fission product metals remain soluble in the melt. Small-scale experiments using gram quantities of uranium dioxide have been performed to investigate themore » feasibility of UO 2 purification from the fission products. The composition of the uranium precipitate as well as data for partitioning of several fission product surrogates between the uranium precipitate and molybdate melt for various melt compositions are presented and discussed. The fission products Cs, Sr, Ru and Rh all displayed very large distribution ratios. The fission products Zr, Pd, and the lanthanides also displayed good distribution ratios (D > 10). A melt consisting of 20 wt% MoO 3-50 wt% Na 2MoO 4-30 wt% UO 2 heated to 1313 K and cooled to 1123 K for the physical separation of the UO 2 product from the melt, and washed once with Na 2MoO 4 displays optimum conditions for separation of the UO 2 from the fission products.« less

Impact of textural anisotropy on syn-kinematic partial melting of natural gneisses: an experimental approach.

NASA Astrophysics Data System (ADS)

Ganzhorn, Anne-Céline; Trap, Pierre; Arbaret, Laurent; Champallier, Rémi; Fauconnier, Julien; Labrousse, Loic; Prouteau, Gaëlle

2015-04-01

Partial melting of continental crust is a strong weakening process controlling its rheological behavior and ductile flow of orogens. This strength weakening due to partial melting is commonly constrained experimentally on synthetic starting material with derived rheological law. Such analog starting materials are preferentially used because of their well-constrained composition to test the impact of melt fraction, melt viscosity and melt distribution upon rheology. In nature, incipient melting appears in particular locations where mineral and water contents are favorable, leading to stromatic migmatites with foliation-parallel leucosomes. In addition, leucosomes are commonly located in dilatants structural sites like boudin-necks, in pressure shadows, or in fractures within more competent layers of migmatites. The compositional layering is an important parameter controlling melt flow and rheological behavior of migmatite but has not been tackled experimentally for natural starting material. In this contribution we performed in-situ deformation experiments on natural rock samples in order to test the effect of initial gneissic layering on melt distribution, melt flow and rheological response. In-situ deformation experiments using a Paterson apparatus were performed on two partially melted natural gneissic rocks, named NOP1 & PX28. NOP1, sampled in the Western Gneiss Region (Norway), is biotite-muscovite bearing gneiss with a week foliation and no gneissic layering. PX28, sampled from the Sioule Valley series (French Massif Central), is a paragneiss with a very well pronounced layering with quartz-feldspar-rich and biotite-muscovite-rich layers. Experiments were conducted under pure shear condition at axial strain rate varying from 5*10-6 to 10-3 s-1. The main stress component was maintained perpendicular to the main plane of anisotropy. Confining pressure was 3 kbar and temperature ranges were 750°C and 850-900°C for NOP1 and PX28, respectively. For the 750°C experiments NOP1 was previously hydrated at room pressure and temperature. According to melt fraction, deformation of partially molten gneiss induced different strain patterns. For low melt fraction, at 750°C, deformation within the initially isotropic gneiss NOP1 is localized along large scales shear-zones oriented at about 60° from main stress component σ1. In these zones quartz grains are broken and micas are sheared. Melt is present as thin film (≥20 µm) at muscovite-quartz grain boundaries and intrudes quartz aggregates as injections parallel to σ1. For higher melt fraction, at 850°C, deformation is homogeneously distributed. In the layered gneiss PX28, deformation is partitioned between mica-rich and quartz-rich layers. For low melt fraction, at 850°C, numerous conjugate shear-bands crosscut mica-rich layers. Melt is present around muscovite grains and intrudes quartz grains in the favor of fractures. For high melt fractions, at 900°C, melt assisted creep within mica-rich layers is responsible for boudinage of the quartz-feldspar rich layers. Melt-induced veining assists the transport of melt toward inter-boudin zones. Finite strain pattern and melt distribution after deformation of PX28 attest for appearance of strong pressure gradients leading to efficient melt flow. The subsequent melt redistribution strongly enhance strain partitioning and strength weakening, as shown by differential stress vs. strain graphs. Our experiments have successfully reproduced microstructures commonly observed in migmatitic gneisses like boudinage of less fertile layers. Comparison between non-layered and layered gneisses attest for strong influence of compositional anisotropies inherited from the protolith upon melt distribution and migmatite strength.

Effects of chemical composition of fly ash on efficiency of metal separation in ash-melting of municipal solid waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okada, Takashi, E-mail: t-okada@u-fukui.ac.jp; Tomikawa, Hiroki

2013-03-15

Highlights: ► Separation of Pb and Zn from Fe and Cu in ash-melting of municipal solid waste. ► Molar ratio of Cl to Na and K in fly ash affected the metal-separation efficiency. ► The low molar ratio and a non-oxidative atmosphere were better for the separation. - Abstract: In the process of metal separation by ash-melting, Fe and Cu in the incineration residue remain in the melting furnace as molten metal, whereas Pb and Zn in the residue are volatilized. This study investigated the effects of the chemical composition of incineration fly ash on the metal-separation efficiency of themore » ash-melting process. Incineration fly ash with different chemical compositions was melted with bottom ash in a lab-scale reactor, and the efficiency with which Pb and Zn were volatilized preventing the volatilization of Fe and Cu was evaluated. In addition, the behavior of these metals was simulated by thermodynamic equilibrium calculations. Depending on the exhaust gas treatment system used in the incinerator, the relationships among Na, K, and Cl concentrations in the incineration fly ash differed, which affected the efficiency of the metal separation. The amounts of Fe and Cu volatilized decreased by the decrease in the molar ratio of Cl to Na and K in the ash, promoting metal separation. The thermodynamic simulation predicted that the chlorination volatilization of Fe and Cu was prevented by the decrease in the molar ratio, as mentioned before. By melting incineration fly ash with the low molar ratio in a non-oxidative atmosphere, most of the Pb and Zn in the ash were volatilized leaving behind Fe and Cu.« less

Lattice thermal conductivity of silicate glasses at high pressures

NASA Astrophysics Data System (ADS)

Chang, Y. Y.; Hsieh, W. P.

2016-12-01

Knowledge of the thermodynamic and transport properties of magma holds the key to understanding the thermal evolution and chemical differentiation of Earth. The discovery of the remnant of a deep magma ocean above the core mantle boundary (CMB) from seismic observations suggest that the CMB heat flux would strongly depend on the thermal conductivity, including lattice (klat) and radiative (krad) components, of dense silicate melts and major constituent minerals around the region. Recent measurements on the krad of dense silicate glasses and lower-mantle minerals show that krad of dense silicate glasses could be significantly smaller than krad of the surrounding solid mantle phases, and therefore the dense silicate melts would act as a thermal insulator in deep lower mantle. This conclusion, however, remains uncertain due to the lack of direct measurements on the lattice thermal conductivity of silicate melts under relevant pressure-temperature conditions. Besides the CMB, magmas exist in different circumstances beneath the surface of the Earth. Chemical compositions of silicate melts vary with geological and geodynamic settings of the melts and have strong influences on their thermal properties. In order to have a better view of heat transport within the Earth, it is important to study compositional and pressure dependences of thermal properties of silicate melts. Here we report experimental results on lattice thermal conductivities of silicate glasses with basaltic and rhyolitic compositions up to Earth's lower mantle pressures using time-domain thermoreflectance coupled with diamond-anvil cell techniques. This study not only provides new data for the thermal conductivity of silicate melts in the Earth's deep interior, but is crucial for further understanding of the evolution of Earth's complex internal structure.

Flux growth utilizing the reaction between flux and crucible

DOE PAGES

Yan, J. -Q.

2015-01-22

Flux growth involves dissolving the components of the target compound in an appropriate flux at high temperatures and then crystallizing under supersaturation controlled by cooling or evaporating the flux. A refractory crucible is generally used to contain the high temperature melt. Moreover, the reaction between the melt and crucible materials can modify the composition of the melt, which typically results in growth failure, or contaminates the crystals. Thus one principle in designing a flux growth is to select suitable flux and crucible materials thus to avoid any reaction between them. In this paper, we review two cases of flux growthmore » in which the reaction between flux and Al 2O 3 crucible tunes the oxygen content in the melt and helps the crystallization of desired compositions. For the case of La 5Pb 3O, the Al 2O 3 crucible oxidizes La to form a passivating La 2O 3 layer which not only prevents further oxidization of La in the melt but also provides [O] to the melt. Finally, in the case of La 0.4Na 0.6Fe 2As 2, it is believed that the Al 2O 3 crucible reacts with NaAsO 2 and the reaction consumes oxygen in the melt thus maintaining an oxygen-free environment.« less

Making rhyolite in a basalt crucible

NASA Astrophysics Data System (ADS)

Eichelberger, John

2016-04-01

Iceland has long attracted the attention of those concerned with the origin of rhyolitic magmas and indeed of granitic continental crust, because it presents no alternative for such magmas other than deriving them from a basaltic source. Hydrothermally altered basalt has been identified as the progenitor. The fact that rhyolite erupts as pure liquid requires a process of melt-crustal separation that is highly efficient despite the high viscosity of rhyolite melt. Volcanoes in Iceland are foci of basaltic magma injection along the divergent plate boundary. Repeated injection produces remelting, digestion, and sometimes expulsion or lateral withdrawal of material resulting in a caldera, a "crucible" holding down-dropped and interlayered lava flows, tephras, and injected sills. Once melting of this charge begins, a great deal of heat is absorbed in the phase change. Just 1% change in crystallinity per degree gives a melt-present body an effective heat capacity >5 times the subsolidus case. Temperature is thus buffered at the solidus and melt composition at rhyolite. Basalt inputs are episodic ("fires") so likely the resulting generation of rhyolite by melting is too. If frequent enough to offset cooling between events, rhyolite melt extractions will accumulate as a rhyolite magma reservoir rather than as discrete crystallized sills. Evidently, such magma bodies can survive multiple firings without themselves erupting, as the 1875 eruption of Askja Caldera of 0.3 km3 of rhyolite equilibrated at 2-km depth without previous leakage over a ten-millennium period and the surprise discovery of rhyolite magma at 2-km depth in Krafla suggest. Water is required for melting; otherwise melting cannot begin at a temperature lower than that of the heat source. Because the solubility of water in melt is pressure-dependent and almost zero at surface pressure, there must be a minimum depth at which basalt-induced melting can occur and a rhyolite reservoir sustained. In practice, the storage limit is likely near 2-km depth at which IDDP-1 and other Krafla boreholes encountered rhyolite melt. Rearrangement of components within the crucible during brewing produces little in terms of a gravity or deformation signals, hence the surprise in finding newly intruded magma. Below 2 km much of the charge in the crucible is near the basalt solidus, so that pockets, sills, and chambers of near-liquidus rhyolite magma will all be close to thermal and chemical equilibrium. Heat is advected upwards from the mantle first by basalt to the crucible, then by rhyolite magma within the crucible, then by hydrothermal fluid to the surface. A major portion of the thermal energy is stored as latent heat of crystallization of rhyolite magma. Such a view challenges some basic tenets of volcano hazard assessment and geothermal energy. The Krafla Magma Drilling Project of the International Continental Scientific Drilling Program will provide a critical test in 2017 by coring from subsolidus granite to liquidus rhyolite, wherein the transitions of heat advection by hydrothermal fluid, to heat conduction, to heat advection by rhyolite magma must occur.

Vitrification of waste with conitnuous filling and sequential melting

DOEpatents

Powell, James R.; Reich, Morris

2001-09-04

A method of filling a canister with vitrified waste starting with a waste, such as high-level radioactive waste, that is cooler than its melting point. Waste is added incrementally to a canister forming a column of waste capable of being separated into an upper zone and a lower zone. The minimum height of the column is defined such that the waste in the lower zone can be dried and melted while maintaining the waste in the upper zone below its melting point. The maximum height of the column is such that the upper zone remains porous enough to permit evolved gases from the lower zone to flow through the upper zone and out of the canister. Heat is applied to the waste in the lower zone to first dry then to raise and maintain its temperature to a target temperature above the melting point of the waste. Then the heat is applied to a new lower zone above the melted waste and the process of adding, drying and melting the waste continues upward in the canister until the entire canister is filled and the entire contents are melted and maintained at the target temperature for the desired period. Cooling of the melted waste takes place incrementally from the bottom of the canister to the top, or across the entire canister surface area, forming a vitrified product.

Fused Bead Analysis of Diogenite Meteorites

NASA Technical Reports Server (NTRS)

Mittlefehldt, D.W.; Beck, B.W.; McSween, H.Y.; Lee, C.T. A.

2009-01-01

Bulk rock chemistry is an essential dataset in meteoritics and planetary science [1]. A common method used to obtain the bulk chemistry of meteorites is ICP-MS. While the accuracy, precision and low detection limits of this process are advantageous [2], the sample size used for analysis (approx.70 mg) can be a problem in a field where small and finite samples are the norm. Fused bead analysis is another bulk rock analytical technique that has been used in meteoritics [3]. This technique involves forming a glass bead from 10 mg of sample and measuring its chemistry using a defocused beam on a microprobe. Though the ICP-MS has lower detection limits than the microprobe, the fused bead method destroys a much smaller sample of the meteorite. Fused bead analysis was initially designed for samples with near-eutectic compositions and low viscosities. Melts generated of this type homogenize at relatively low temperatures and produce primary melts near the sample s bulk composition [3]. The application of fused bead analysis to samples with noneutectic melt compositions has not been validated. The purpose of this study is to test if fused bead analysis can accurately determine the bulk rock chemistry of non-eutectic melt composition meteorites. To determine this, we conduct two examinations of the fused bead. First, we compare ICP-MS and fused bead results of the same samples using statistical analysis. Secondly, we inspect the beads for the presence of crystals and chemical heterogeneity. The presence of either of these would indicate incomplete melting and quenching of the bead.

Metal matrix-metal nanoparticle composites with tunable melting temperature and high thermal conductivity for phase-change thermal storage.

PubMed

Liu, Minglu; Ma, Yuanyu; Wu, Hsinwei; Wang, Robert Y

2015-02-24

Phase-change materials (PCMs) are of broad interest for thermal storage and management applications. For energy-dense storage with fast thermal charging/discharging rates, a PCM should have a suitable melting temperature, large enthalpy of fusion, and high thermal conductivity. To simultaneously accomplish these traits, we custom design nanocomposites consisting of phase-change Bi nanoparticles embedded in an Ag matrix. We precisely control nanoparticle size, shape, and volume fraction in the composite by separating the nanoparticle synthesis and nanocomposite formation steps. We demonstrate a 50-100% thermal energy density improvement relative to common organic PCMs with equivalent volume fraction. We also tune the melting temperature from 236-252 °C by varying nanoparticle diameter from 8.1-14.9 nm. Importantly, the silver matrix successfully prevents nanoparticle coalescence, and no melting changes are observed during 100 melt-freeze cycles. The nanocomposite's Ag matrix also leads to very high thermal conductivities. For example, the thermal conductivity of a composite with a 10% volume fraction of 13 nm Bi nanoparticles is 128 ± 23 W/m-K, which is several orders of magnitude higher than typical thermal storage materials. We complement these measurements with calculations using a modified effective medium approximation for nanoscale thermal transport. These calculations predict that the thermal conductivity of composites with 13 nm Bi nanoparticles varies from 142 to 47 W/m-K as the nanoparticle volume fraction changes from 10 to 35%. Larger nanoparticle diameters and/or smaller nanoparticle volume fractions lead to larger thermal conductivities.

Pre-1991 sulfur transfer between mafic injections and dacite magma in the Mt. Pinatubo reservoir

USGS Publications Warehouse

Di, Muro A.; Pallister, J.; Villemant, B.; Newhall, C.; Semet, M.; Martinez, M.; Mariet, C.

2008-01-01

Before the 1991-1992 activity, a large andesite lava dome belonging to the penultimate Pinatubo eruptive period (Buag ??? 500??BP) formed the volcano summit. Buag porphyritic andesite contains abundant amphibole-bearing microgranular enclaves of basaltic-andesite composition. Buag enclaves have lower K2O and incompatible trace element (LREE, U, Th) contents than mafic pulses injected in the Pinatubo reservoir during the 1991-1992 eruptive cycle. This study shows that Buag andesite formed by mingling of a hot, water-poor and reduced mafic magma with cold, hydrous and oxidized dacite. Depending on their size, enclaves experienced variable re-equilibration during mixing/mingling. Re-equilibration resulted in hydration, oxidation and transfer of mobile elements (LILE, Cu) from the dacite to the mafic melts and prompted massive amphibole crystallization. In Buag enclaves, S-bearing phases (sulfides, apatite) and melt inclusions in amphibole and plagioclase record the evolution of sulfur partition among melt, crystal and fluid phases during magma cooling and oxidation. At high temperature, sulfur is partitioned between andesitic melt and sulfides (Ni-pyrrhotite). Magma cooling, oxidation and hydration resulted in exsolution of a S-Cl-H2O vapor phase at the S-solubility minimum near the sulfide-sulfate redox boundary. Primary magmatic sulfide (pyrrhotite) and xenocrystic sulfide grains (pyrite), recycled together with olivines and pyroxenes from old mafic intrusives, were replaced by Cu-rich phases (chalcopyrite, cubanite) and, partially, by Ba-Sr sulfate. Sulfides degassed and transformed into residual spongy magnetite in response to fS2 drop during final magma ascent and decompression. Our research suggests that a complete evaluation of the sulfur budget at Pinatubo must take into account the en route S assimilation from the country rocks. Moreover, this study shows that the efficiency of sulfur transfer between mafic recharges and injected magmas is controlled by the extent and rate of mingling, hydrous flushing and melt oxidation. Vigorous mixing/mingling and transformation of the magmatic recharge into a spray of small enclaves is required in order to efficiently strip their primary S-content that otherwise remains locked in the sulfides. Hydrous flushing increases the magma oxidation state of the recharges and modifies their primary volatile concentrations that cannot be recovered by the study of late-formed mineral phases and melt inclusions. Conversely, S stored in both late-formed Cu-rich sulfides and interstitial rhyolitic melt represents the pre-eruptive sulfur budget immediately available for release from mafic enclaves during their decompression. ?? 2008 Elsevier B.V.

CO2 solubility and speciation in rhyolitic sediment partial melts at 1.5-3.0 GPa - Implications for carbon flux in subduction zones

NASA Astrophysics Data System (ADS)

Duncan, Megan S.; Dasgupta, Rajdeep

2014-01-01

Partial melts of subducting sediments are thought to be critical agents in carrying trace elements and water to arc basalt source regions. Sediment partial melts may also act as a carrier of CO2. However, the CO2 carrying capacity of natural rhyolitic melts that derive from partial fusion of downgoing sediment at sub-arc depths remains unconstrained. We conducted CO2-solubility experiments on a rhyolitic composition similar to average, low-degree experimental partial melt of pelitic sediments between 1.5 and 3.0 GPa at 1300 °C and containing variable water content. Concentrations of water and carbon dioxide were measured using FTIR. Molecular CO2(CO2mol.) and carbonate anions (CO32-) both appear as equilibrium species in our experimental melts. Estimated total CO2 concentrations (CO2mol.+CO32-) increased with increasing pressure and water content. At 3.0 GPa, the bulk CO2 solubility are in the range of ∼1-2.5 wt.%, for melts with H2O contents between 0.5 and 3.5 wt.%. For melts with low H2O content (∼0.5 wt.%), CO2mol. is the dominant carbon species, while in more H2O-rich melts CO32- becomes dominant. The experimentally determined, speciation-specific CO2 solubilities yielded thermodynamic parameters that control dissolution of CO2 vapor both as CO2mol. and as CO32- in silicate melt for each of our compositions with different water content; CO2vapor ↔CO2melt :lnK0=-15 to -18, ΔV0 = 29 to 14 cm3 mol-1 and CO2vapor +Omelt →CO32-melt :lnK0=-20 to -14, ΔV0 = 9 to 27 cm3 mol-1, with ΔV0 of reaction being larger for formation of CO2mol. in water-poor melts and for formation of CO32- in water-rich melts. Our bulk CO2 solubility data, [CO2] (in wt.%) can be fitted as a function of pressure, P (in GPa) and melt water content, [H2O] (in wt.%) with the following function: [CO2](wt.%)=(-0.01108[H2O]+0.03969)P2+(0.10328[H2O]+0.41165)P. This parameterization suggests that over the range of sub-arc depths of 72-173 km, water-rich sediment partial melt may carry as much as 2.6-5.5 wt.% CO2 to the sub-arc mantle source regions. At saturation, 1.6-3.3 wt.% sediment partial melt relative to the mantle wedge is therefore sufficient to bring up the carbon budget of the mantle wedge to produce primary arc basalts with 0.3 wt.% CO2. Sediment plumes in mantle wedge: Sediment plumes or diapirs may form from the downgoing slab because the sediment layer atop the slab is buoyant relative to the overlying, hanging wall mantle (Currie et al., 2007; Behn et al., 2011). Via this process, sediment layers with carbonates would carry CO2 to the arc source region. Owing to the higher temperature in the mantle wedge, carbonate can breakdown. Behn et al. (2011) suggested that sediment layers as thin as 100 m, appropriate for modern arcs, could form sediment diapirs. They predicted that diapirs would form from the slab in the sub-arc region for most subduction zones today without requiring hydrous melting. H2O-rich fluid driven carbonate breakdown: Hydrous fluid flushing of the slab owing to the breakdown of hydrous minerals could drive carbonate breakdown (Kerrick and Connolly, 2001b; Grove et al., 2002; Gorman et al., 2006). The addition of water would cause decarbonation creating an H2O-CO2-rich fluid that would then flux through the overlying sediment layer, lower the solidus temperature, and trigger melting. Recent geochemical (Cooper et al., 2012) and geodynamic (van Keken, 2003; Syracuse et al., 2010) constraints suggest that the sub-arc slab top temperatures are above the hydrous fluid-present sediment solidus, thus in the presence of excess fluid, both infiltration induced decarbonation and sediment melting may occur. Hot subduction: This is relevant for subduction zones such as Cascadia and Mexico, where slab-surface temperatures are estimated to be higher (Syracuse et al., 2010). A higher temperature could cause carbonate breakdown and sediment partial melting without requiring a hydrous fluid flux. In this case a relatively dry silicate sediment melt will have the opportunity to dissolve and carry CO2. For hot subduction zones, even if sedimentary layer itself does not carry carbonate, CO2 released from basalt-hosted carbonates may be dissolved in sediment partial melt. Experiments conducted on subducted sediment compositions show that the partial melt compositions are generally rhyolitic (Johnson and Plank, 1999; Hermann and Green, 2001; Schmidt et al., 2004; Auzanneau et al., 2006; Hermann and Spandler, 2008; Spandler et al., 2010; Tsuno and Dasgupta, 2011). Therefore, solubility of CO2 in rhyolitic sediment partial melts needs to be known. Previous studies on rhyolitic melts experimentally determined CO2 solubility from 0.05 to 0.66 GPa (Fig. 1; Fogel and Rutherford, 1990; Blank et al., 1993; Tamic et al., 2001). This pressure range is not appropriate for global sub-arc depth range of 72-173 km (Syracuse and Abers, 2006) settings (P = 2-5 GPa). Carbon dioxide solubility experiments at pressures from 1.5 to 3.5 GPa are available but only on simple compositions - i.e., albite, which does not have the chemical complexity of natural sediment partial melts (Fig. 1; Brey, 1976; Mysen, 1976; Mysen et al., 1976; Mysen and Virgo, 1980; Stolper et al., 1987; Brooker et al., 1999). For example, natural rhyolitic melt derived from partial fusion of pelitic sediments contain non-negligible concentrations of Ca2+, Mg2+, Fe2+. Many of these studies were also conducted under mixed-volatile conditions (CO2 + H2O) with H2O contents from 0.06 to 3.3 wt.%. These studies were used in calculating various solubility models: Volatile-Calc (Newman and Lowenstern, 2002), that of Liu et al. (2005), and that of Papale et al. (2006). Volatile-Calc can be used to calculate CO2 solubility only on a generic rhyolite composition up to 0.5 GPa. The model of Liu et al. (2005) is also on a generic rhyolite up to 0.5 GPa, but can calculate mixed volatile concentrations provided the vapor composition is known. The model of Papale et al. (2006) can be used to calculate mixed volatile concentrations for a melt composition of interest, but only up to 1.0 GPa.The literature data show that CO2 solubility increases with increasing pressure and decreases with increasing melt silica content (decreasing NBO/T; e.g., Brooker et al., 2001). The effect of temperature remains somewhat ambiguous, but is thought to be relatively smaller than the pressure or compositional effects, with Mysen (1976) measuring increasing CO2 solubility with temperature for albite melt, Brooker et al. (2001) and Fogel and Rutherford (1990) noticing decreasing CO2 solubility with increasing temperature, and Stolper et al. (1987) concluding that temperature has essentially no effect on total melt CO2 concentration at saturation. The presence of water in the melt also is known to affect CO2 solution (e.g., Mysen, 1976; Eggler and Rosenhauer, 1978), yet quantitative effect of water on CO2 solution in natural rhyolitic melt has only been investigated up to 0.5 GPa (Tamic et al., 2001). In order to determine the CO2 carrying capacity of sediment partial melts, experiments must be conducted at conditions (pressure, temperature, major element compositions, and XH2O) relevant to sub-arc settings.In this study we measured the solubility and speciation of CO2 in rhyolitic sediment partial melts. Experiments were conducted from 1.5 to 3.0 GPa at 1300 °C with variable water contents and synthesized glasses were analyzed for water and carbon speciation using Fourier-transformed infrared spectroscopy. Our measured solubility data allowed us to constrain volume change and equilibrium constant of the CO2 dissolution reactions. Moreover, we parameterize CO2 solubility in sediment partial melt as a function of pressure and melt water content. Our data and empirical model suggest that the CO2 carrying capacity of sediment partial melts is sufficiently high at sub-arc depths and hydrous sediment melt can potentially carry the necessary dose of CO2 to arc mantle source regions.

The He isotope composition of the earliest picrites erupted by the Ethiopia plume, implications for mantle plume source

NASA Astrophysics Data System (ADS)

Stuart, Finlay; Rogers, Nick; Davies, Marc

2016-04-01

The earliest basalts erupted by mantle plumes are Mg-rich, and typically derived from mantle with higher potential temperature than those derived from the convecting upper mantle at mid-ocean ridges and ocean islands. The chemistry and isotopic composition of picrites from CFB provide constraints on the composition of deep Earth and thus the origin and differentiation history. We report new He-Sr-Nd-Pb isotopic composition of the picrites from the Ethiopian flood basalt province from the Dilb (Chinese Road) section. They are characterized by high Fe and Ti contents for MgO = 10-22 wt. % implying that the parent magma was derived from a high temperature low melt fraction, most probably from the Afar plume head. The picrite 3He/4He does not exceed 21 Ra, and there is a negative correlation with MgO, the highest 3He/4He corresponding to MgO = 15.4 wt. %. Age-corrected 87Sr/86Sr (0.70392-0.70408) and 143Nd/144Nd (0.512912-0.512987) display little variation and are distinct from MORB and OIB. Age-corrected Pb isotopes display a significant range (e.g. 206Pb/204Pb = 18.70-19.04) and plot above the NHRL. These values contrast with estimates of the modern Afar mantle plume which has lower 3He/4He and Sr, Nd and Pb isotope ratios that are more comparable with typical OIB. These results imply either interaction between melts derived from the Afar mantle plume and a lithospheric component, or that the original Afar mantle plume had a rather unique radiogenic isotope composition. Regardless of the details of the origins of this unusual signal, our observations place a minimum 3He/4He value of 21 Ra for the Afar mantle plume, significantly greater than the present day value of 16 Ra, implying a significant reduction over 30 Myr. In addition the Afar source was less degassed than convecting mantle but more degassed than mantle sampled by the proto-Iceland plume (3He/4He ~50 Ra). This suggests that the largest mantle plumes are not sourced in a single deep mantle domain with a common depletion history and that they do not mix with shallower mantle reservoirs to the same extent.

Configurational Heat Capacity of Na- and Ca-bearing Aluminosilicate Melts

NASA Astrophysics Data System (ADS)

Webb, S. L.

2006-12-01

The Na2O-Al2O3-SiO2 and CaO-Al2O3-SiO2 systems are used as analogs for the more complex natural magmatic systems of the Earth in studies of the physical properties, structure and flow mechanisms of silicate melts. Although the description of flow in binary alkali-silicate melts is clear; that for multi-oxide compositions quickly becomes very complex. The addition of aluminium to melts creates the need for a charge-balancing cation for the tetrahedrally co-ordinated Al3+. With the presence of both mono- and di-valent ions there are questions about which atom is preferred as the charge balancer and which will create non-bridging oxygens. This study addresses the structure of peraluminous and peralkaline/metaluminous Na2O-CaO-Al2O3-SiO2 melts and the change in structure with composition via determination of their shear viscosity and heat capacity. Viscosity has been determined using the micropenetration technique and the heat capacity and configurational heat capacity have been determined by differential scanning calorimetry. While the viscosity of these melts indicates structural changes at the condition where there are no longer enough Na+ or Ca2+ to charge balance all of the Al3+ in tetrahedral co-ordination, it is the heat capacity data which provides more information about the energy required for flow to occur in the melts as the structure changes due to changing composition. The configurational heat capacity can be determined from the difference between the liquid (cpl) and the glass (cpg) heat capacity at the glass transition temperature. To a first approximation cpg can be calculated from a linear summation of the cps of the oxide components. Similarly, if there are no anomalous changes in melt structure upon heating through Tg, the cpl will be a linear sum of the contributions of the component oxides. Configurational entropy Sconf(Tg) has been calculated from the viscosity data using the Adam-Gibbs equation for viscosity as a function of configurational entropy and temperature. In addition to the change in structure implied from changes in the trends of the viscosity and heat capacity data when there are no longer enough charge balancers for all of the Al3+ in tetrahedral co-ordination, there also appears to be a change in structure at the composition where there are no longer enough Ca2+ in the melt that each Al3+ tetrahedron has its own charge balancer that is the composition at which pairs of Al3+ tetrahedra must share a Ca2+ as charge balancer.

Structural environments of incompatible elements in silicate glass/melt systems: I. Zirconium at trace levels

NASA Astrophysics Data System (ADS)

Farges, Franã§Ois; Ponader, Carl W.; Brown, Gordon E., Jr.

1991-06-01

The structural environments of trace levels (2˜000 ppm) of Zr 4+ in several silicate glasses were examined as a function of melt composition and polymerization using Extended X-ray Absorption Fine Structure (EXAFS) spectroscopy. Glass compositions investigated were albite (NaAlSi 3O 8: AB) and a peralkaline composition (Na 3.3AlSi 7O 17: PR)- Zirconium was added to the oxide-carbonate mix prior to melting in the form of ZrO 2 (baddeleyite). A second set of Zr-silicate glasses containing 2000 ppm Zr and 1.0 to 2.4 wt% halogens (F as NaF and Cl as NaCl) was also synthesized. These included the Zr-AB and Zr-PR base-glass compositions as well as Zr-sodium trisilicate composition (Na2Si 3O 7: TS). In all glasses studied, Zr is mainly 6-coordinated by oxygen atoms ( d[Zr-O] ˜2.07 ± 0.01 Å). In the most polymerized glass (AB), a small but significant amount of Zr was also found to occur in 8-coordinated sites ( d[Zr-O] ˜2.22 Å). No clear evidence for F or Cl complexes of Zr was observed in any of the halogen-containing glasses. The regularity of the Zr site increases in the series AB < TS ˜PR. We attribute this change to an increase in the number of non-bridging oxygens in the first-coordination sphere of Zr related to the depolymerizing effects of halogens and/or sodium. Minor but significant interactions of Zr with the tetrahedral network were observed ( d[Zr-{Si, Al}] ˜3.65-3.71 Å ± 0.03 Å), which are consistent with Zr-O-{Si, Al} angles close to 160-170°, as in catapleiite (Na 2ZrSi 3O 9 · 2H 2O). Intermediaterange order, as reflected by the presence and number of second-neighbor {Si, Al} around Zr, increases significantly with increasing melt polymerization. The local environment around Zr is more strongly influenced by bonding requirements than by the network topology of the melt. Stabilization of zirconium in 6-coordinated sites in relatively depolymerized melts should act to decrease the crystal-melt partition coefficients of Zr and may explain the normally incompatible character of Zr during magmatic differentiation. The presence of Zr in sites of higher coordination (ZrO 8) in highly polymerized melts could be a precursor to the crystallization of zircon from such melts and thus may explain why Zr becomes a more compatible element, especially in the latest stages of magmatic differentiation.

Melting of the primitive martian mantle at 0.5-2.2 GPa and the origin of basalts and alkaline rocks on Mars

NASA Astrophysics Data System (ADS)

Collinet, Max; Médard, Etienne; Charlier, Bernard; Vander Auwera, Jacqueline; Grove, Timothy L.

2015-10-01

We have performed piston-cylinder experiments on a primitive martian mantle composition between 0.5 and 2.2 GPa and 1160 to 1550 °C. The composition of melts and residual minerals constrain the possible melting processes on Mars at 50 to 200 km depth under nominally anhydrous conditions. Silicate melts produced by low degrees of melting (<10 wt.%) were analyzed in layers of vitreous carbon spheres or in micro-cracks inside the graphite capsule. The total range of melt fractions investigated extends from 5 to 50 wt.%, and the liquids produced display variable SiO2 (43.7-59.0 wt.%), MgO (5.3-18.6 wt.%) and Na2O + K2O (1.0-6.5 wt.%) contents. We provide a new equation to estimate the solidus temperature of the martian mantle: T (°C) = 1033 + 168.1 P (GPa) - 14.22P2 (GPa), which places the solidus 50 °C below that of fertile terrestrial peridotites. Low- and high-degree melts are compared to martian alkaline rocks and basalts, respectively. We suggest that the parental melt of Adirondack-class basalts was produced by ∼25 wt.% melting of the primitive martian mantle at 1.5 GPa (∼135 km) and ∼1400 °C. Despite its brecciated nature, NWA 7034/7533 might be composed of material that initially crystallized from a primary melt produced by ∼10-30 wt.% melting at the same pressure. Other igneous rocks from Mars require mantle reservoirs with different CaO/Al2O3 and FeO/MgO ratios or the action of fractional crystallization. Alkaline rocks can be derived from mantle sources with alkali contents (∼0.5 wt.%) similar to the primitive mantle.

Eucrite Impact Melt NWA 5218 - Evidence for a Large Crater on Vesta

NASA Technical Reports Server (NTRS)

Wittmann, Axel; Hiroi, Takahiro; Ross, Daniel K.; Herrin, Jason S.; Rumble, Douglas, III; Kring, David A.

2011-01-01

Northwest Africa (NWA) 5218 is a 76 g achondrite that is classified as a eucrite [1]. However, an initial classification [2] describes it as a "eucrite shock-melt breccia...(in which) large, partially melted cumulate basalt clasts are set in a shock melt flow...". We explore the petrology of this clast-bearing impact melt rock (Fig. 1), which could be a characteristic lithology at large impact craters on asteroid Vesta [3]. Methods: Optical microscopy, scanning electronmicroscopy, and Raman spectroscopy were used on a thin section (Fig. 1) for petrographic characterization. The impact melt composition was determined by 20 m diameter defocused-beam analyses with a Cameca SX-100 electron microprobe. The data from 97 spots were corrected for mineral density effects [4]. Constituent mineral phases were analyzed with a focusedbeam. Bidirectonal visible and near-infrared (VNIR) and biconical FT-IR reflectance spectra were measured on the surface of a sample slab on its central melt area and on an eucrite clast, and from 125-500 m and <125 m powders of melt. Results: General petrography: The sample specimen is a coherent, medium dark-grey (N4), melt rock. The thin section captures a central, subophitic-textured melt that contains 1 cm to tens of m-size subangular to rounded, variably-shocked eucrite clasts. Clasts >100 m are coarse-grained with equigranular 1 mm size plagioclase, quartz, and clinopyroxene (Fig. 1). Single crystals of chromite, ilmenite, zircon, Ca-Mg phosphate, Fe-metal, and troilite are embedded in the melt. Polymineralic clasts are mostly compositionally similar to the above mentioned larger clasts but scarce granulitic fragments are observed as well.

Melt damage simulation of W-macrobrush and divertor gaps after multiple transient events in ITER

NASA Astrophysics Data System (ADS)

Bazylev, B. N.; Janeschitz, G.; Landman, I. S.; Loarte, A.; Pestchanyi, S. E.

2007-06-01

Tungsten in the form of macrobrush structure is foreseen as one of two candidate materials for the ITER divertor and dome. In ITER, even for moderate and weak ELMs when a thin shielding layer does not protect the armour surface from the dumped plasma, the main mechanisms of metallic target damage remain surface melting and melt motion erosion, which determines the lifetime of the plasma facing components. The melt erosion of W-macrobrush targets with different geometry of brush surface under the heat loads caused by weak ELMs is numerically investigated using the modified code MEMOS. The optimal angle of brush surface inclination that provides a minimum of surface roughness is estimated for given inclination angles of impacting plasma stream and given parameters of the macrobrush target. For multiple disruptions the damage of the dome gaps and the gaps between divertor cassettes caused by the radiation impact is estimated.

Impact melting of the Cachari eucrite 3.0 Gy ago

NASA Technical Reports Server (NTRS)

Bogard, D. D.; Taylor, G. J.; Keil, K.; Smith, M. R.; Schmitt, R. A.

1985-01-01

The chemical compositions and Ar-isotope gas-retention ages of host phase and glass veins in the Cachari eucrite are determined by microprobe and neutron-activation analysis and mass spectrometry, respectively. The results are presented in tables, graphs, and back-scattered electron images and characterized in detail. The compositions are found to support the thesis that the glass formed by shock melting of the host rock (or of rock having the same composition). The Ar-39/Ar-40 ages of host and glass are given as 3.04 + or - 0.07 Gyr and 3.47 + or - 0.04 Gyr, respectively; the former value is taken as the true data of melting, and the latter is attributed to incomplete postmelt degassing of Ar from the glass phase. The implications of the relative youth of this and other eucrites and howardites for the regolith history of the parent body are considered.

The temperature of primary melts and mantle sources of komatiites, OIBs, MORBs and LIPs

NASA Astrophysics Data System (ADS)

Sobolev, Alexander

2015-04-01

There is general agreement that the convecting mantle, although mostly peridotitic in composition, is compositionally and thermally heterogeneous on different spatial scales. The amount, sizes, temperatures and compositions of these heterogeneities significantly affect mantle dynamics because they may diverge greatly from dominant peridotites in their density and fusibility. Differences in potential temperature and composition of mantle domains affect magma production and cannot be easily distinguished from each other. This has led to radically different interpretations of the melting anomalies that produce ocean-island basalts, large igneous provinces and komatiites: most scientists believe that they originate as hot, deep-sourced mantle plumes; but a small though influential group (e.g. Anderson 2005, Foulger, 2010) propose that they derive from high proportions of easily fusible recycled or delaminated crust, or in the case of komatiites contain large amount of H2O (e.g. Grove & Parman, 2004). The way to resolve this ambiguity is an independent estimation of temperature and composition of mantle sources of various types of magma. In this paper I report application of newly developed olivine-spinel-melt geothermometers based on partition of Al, Cr, Sc and Y for different primitive lavas from mid-ocean ridges, ocean-island basalts, large igneous provinces and komatiites. The results suggest significant variations of crystallization temperature for the same Fo of high magnesium olivines of different types of mantle-derived magmas: from the lowest (down to 1220 degree C) for MORB to the highest (up to over 1500 degree C) for komatiites and Siberian meimechites. These results match predictions from Fe-Mg olivine-melt equilibrium and confirm the relatively low temperature of the mantle source of MORB and higher temperatures in the mantle plumes that produce the OIB of Iceland, Hawaii, Gorgona, Archean komatiites and several LIPs (e.g Siberian and NAMP). The established liquidus temperatures and compositions of primary melts allow estimating potential temperatures and compositions of their mantle sources. The results strongly confirm mantle plume theory and presence of variable amounts of recycled crustal material in the mantle sources. This study has been founded by Russian Science Foundation grant 14-17-00491.

Aegirine-melt element partitioning and implications for the formation of nepheline syenite REE deposits

NASA Astrophysics Data System (ADS)

Beard, Charles; van Hinsberg, Vincent; Stix, John; Wilke, Max

2017-04-01

Sodic clinopyroxene is a key fractionating phase in alkaline magmatic systems but its impact on metal enrichment processes, and the formation of REE + HFSE mineralizations in particular, is not fully understood. Sodic pyroxenes appear to more readily incorporate REE than their calcic equivalents1. Despite this, melts in evolved alkaline systems can attain high REE contents, even up to economic levels (e.g. the Nechalacho layered suite in Canada2). To constrain the control of pyroxene on REE + HFSE behaviour in alkaline magmas, a series of internally heated pressure vessel experiments was performed to determine pyroxene-melt element partitioning systematics. Synthetic trachy-andesite to phonolite compositions were run water saturated at 650-825°C with fO2 buffered by ca. 1 bar of H2 (QFM + 1) or by Hm-Mt (QFM +5). Fluorine was added to selected experiments (0.3 to 2.5 wt %) to ascertain its effect on element partitioning. Run products were analysed by EMP for major elements and LA-ICP-MS for trace elements. Mineral and glass compositions bracket the compositions of natural alkaline systems, allowing for direct application of our experimental results to nature. Our results indicate that REE partitioning systematics vary strongly with pyroxene composition: Diopside-rich pyroxenes (Aeg5-25) prefer the MREE, medium aegirine pyroxenes (Aeg25-50) preferentially incorporate the LREE, whereas high aegirine pyroxenes (Aeg55-95) strongly prefer HREE. REE partitioning coefficients are 0.3-40, typically 2-6, with minima for high aegirine pyroxenes. Melt composition (e.g. (Na+K)/Al) also impacts partitioning although to a lesser extent, except for the F-content, which shows no impact at all. The composition of fractionating pyroxene has a major impact on the REE pattern of the residual melt, and thus on the ability of a system to develop economic concentrations of the REE. Element partitioning systematics suggest that late-crystallising aegirine-rich cumulates would be HREE-rich, in accord with the composition of mineralised intrusions, such as Nechalacho2. 1 - Marks, M., Halama, R., Wenzel, T. & Markl, G., 2004. Chem. Geol. 211, 185-215. 2 - Möller, V. & Williams-Jones, A. E., 2016. J. Petrology 57, 229-276.

A carbon-rich region in Miller Range 091004 and implications for ureilite petrogenesis

NASA Astrophysics Data System (ADS)

Day, James M. D.; Corder, Christopher A.; Cartigny, Pierre; Steele, Andrew M.; Assayag, Nelly; Rumble, Douglas; Taylor, Lawrence A.

2017-02-01

Ureilite meteorites are partially melted asteroidal-peridotite residues, or more rarely, cumulates that can contain greater than three weight percent carbon. Here we describe an exceptional C-rich lithology, composed of 34 modal % large (up to 0.8 mm long) crystalline graphite grains, in the Antarctic ureilite meteorite Miller Range (MIL) 091004. This C-rich lithology is embedded within a silicate region composed dominantly of granular olivine with lesser quantities of low-Ca pyroxene, and minor FeNi metal, high-Ca pyroxene, spinel, schreibersite and troilite. Petrological evidence indicates that the graphite was added after formation of the silicate region and melt depletion. Associated with graphite is localized reduction of host olivine (Fo88-89) to nearly pure forsterite (Fo99), which is associated with FeNi metal grains containing up to 11 wt.% Si. The main silicate region is typical of ureilite composition, with highly siderophile element (HSE) abundances ∼0.3 × chondrite, 187Os/188Os of 0.1260-0.1262 and Δ17O of -0.81 ± 0.16‰. Mineral trace-element analyses reveal that the rare earth elements (REE) and the HSE are controlled by pyroxene and FeNi metal phases in the meteorite, respectively. Modeling of bulk-rock REE and HSE abundances indicates that the main silicate region experienced ∼6% silicate and >50% sulfide melt extraction, which is at the lower end of partial melt removal estimated for ureilites. Miller Range 091004 demonstrates heterogeneous distribution of carbon at centimeter scales and a limited range in Mg/(Mg + Fe) compositions of silicate grain cores, despite significant quantities of carbon. These observations demonstrate that silicate rim reduction was a rapid disequilibrium process, and came after silicate and sulfide melt removal in MIL 091004. The petrography and mineral chemistry of MIL 091004 is permissive of the graphite representing late-stage C-rich melt that pervaded silicates, or carbon that acted as a lubricant during anatexis and impact disruption in the parent body. Positive correlation of Pt/Os ratios with olivine core compositions, but a wide range of oxygen isotope compositions, indicates that ureilites formed from a compositionally heterogeneous parent body that experienced variable sulfide and metal melt-loss that is most pronounced in relatively oxidized ureilites with Δ17O between -1.5 and ∼0‰.

Experimental simulation of the alkali-carbonate metasomatism

NASA Astrophysics Data System (ADS)

Gorbachev, Nikolay; Kostyuk, Anastasia

2010-05-01

Close association of alkaline and ultrabasic rocks, carbonatites, apatitic and sulfidic mineralization, features of structure testify about mantle a source and the important role alcalic-carbonaceous fluids in genesis of these rocks. Formation alkaline silicate, carbonaceous and sulfidic melts, phase relationship, behaviour of the ti-tan, phosphorus, sulphur and zircon has been experimentally studied at pressure 3.9 GPa, temperature 1250°С in system peridotit-basalt (eclogite)-alcalic-carbonaceous fluid with additives in quality acces-sory minerals, apatite, nickel-containing pyrrhotite, ilmenite, zircon. Experiments were carried out using of apparatus high pressure (piston cilinder and anvil with hole) by a quenching technique. It was used two ampoules (platinum and peridotite, content basalt powder) method. Duration of experiments was 6-8 hours. Products of experiments were studied on electronic scanning microscope Tescan VEGA TS 5130MM with YAG detector of secondary and reflected elec-tron and energy-dispersive the x-ray microanalyzer with semi-conductor Si (Li) detector INCA Energy 350. The morphology, structure and relationship of glass, inclusions of carbonatic and sulfidic globules specify in existence in the conditions of experiment immiscibility silicate, carbonate and sulfidic melts. The composition of silicate melt answered phonolite, carbonaceous melts it is essential calciferous composition with an impurity of alkaline metals and silicate components. Solubility of zircon in silicate melts reached 0.8 wt.% ZrO2, in co-existing carbonaceous melt - 1.5 wt.%. Concentration TiO2 and Р2О5 in silicate melt reached 2 wt.%, in carbonaceous melt - 1.7 wt.% TiO2 and up to 14 wt.% Р2О5. Concentration of sulphur in these melts did not exceed 0.2 мас. %. From minerals of liqudus the main concentrators of the titan and phosphorus were the X-phase and phlogopite - up to 8 wt.% TiO2 and up to 3 wt.% Р2О5 in the X-phase, up to 6 wt. % TiO2 and to 2.5 wt. % Р2О5 in phlogopite. Absence ilmenite and apatite in experimental samples under the studied conditions is obviously caused by their high solubility in co-existing phases. The composition of X-phase is similar to composition of Cpx, but X-phase enrich in TiO2 and de-plete in SiO2 . The partition coefficient of oxides some elements between silicate and carbonaceous melts Dka/si increasing from SiO2 (D<1) to CaO (D>10). Reduction of solubility of apatite in alkaline silicate melt at pressure decline promotes silicate-phosphate stratification and formation of apatite mineralization at introduction of mantle magmas into the earth crust. Supported by grant RFBR № 09-05-01131, ONZ th. 2

Electrolysis of lunar soil to produce oxygen and metals

NASA Technical Reports Server (NTRS)

Colson, Russell O.; Haskin, Larry A.; Keller, R.

1991-01-01

The discussion of melt electrolysis consists of three sections. The implications of the chemistry and physics of fluxed and raw melts on melt electrolysis are discussed first. This includes discussion of the factor that influence melt resistivity, melt viscosity, oxygen production efficiency, and the theoretical energy required to produce oxygen. Second, the implications of phase equilibria and solubilities in silicate melts on the selection of materials for container and electrodes are discussed. The implications of proposed container and electrode materials on melt composition and how this effects expected resistivities, viscosities, as outlined in the first section are discussed. Finally, a general discussion of the basic features of both the fluxed and unfluxed melt electrolysis is given, including their advantages and disadvantages and how they compare with alternative processes.

SiC-Based Composite Materials Obtained by Siliconizing Carbon Matrices

NASA Astrophysics Data System (ADS)

Shikunov, S. L.; Kurlov, V. N.

2017-12-01

We have developed a method for fabrication of parts of complicated configuration from composite materials based on SiC ceramics, which employs the interaction of silicon melt with the carbon matrix having a certain composition and porosity. For elevating the operating temperatures of ceramic components, we have developed a method for depositing protective silicon-carbide coatings that is based on the interaction of the silicon melt and vapor with carbon obtained during thermal splitting of hydrocarbon molecules. The new structural ceramics are characterized by higher operating temperatures; chemical stability; mechanical strength; thermal shock, wear and radiation resistance; and parameters stability.

Interaction of tungsten with tungsten carbide in a copper melt

NASA Astrophysics Data System (ADS)

Bodrova, L. E.; Goida, E. Yu.; Pastukhov, E. A.; Marshuk, L. A.; Popova, E. A.

2013-07-01

The chemical interaction between tungsten and tungsten carbide in a copper melt with the formation of W2C at 1300°C is studied. It is shown that the mechanical activation of a composition consisting of copper melt + W and WC powders by low-temperature vibrations initiates not only the chemical interaction of its solid components but also their refinement.

Melt rheological properties of natural fiber-reinforced polypropylene

Treesearch

Jarrod J. Schemenauer; Tim A. Osswald; Anand R. Sanadi; Daniel F. Caulfield

2000-01-01

The melt viscosities and mechanical properties of 3 different natural fiber-polypropylene composites were investigated. Coir (coconut), jute, and kenaf fibers were compounded with polypropylene at 30% by weight content. A capillary rheometer was used to evaluate melt viscosity. The power-law model parameters are reported over a shear rate range between 100 to 1000 s–1...

Determining the thermodynamic melting parameters of sulfamethoxazole, trimethoprim, urea, nicodin, and their double eutectics by differential scanning calorimetry

NASA Astrophysics Data System (ADS)

Agafonova, E. V.; Moshchenskii, Yu. V.; Tkachenko, M. L.

2013-08-01

The literature data on the thermodynamic melting characteristics of sulfamethoxazole, urea, trimethoprim, and nicodin are analyzed for individual compounds. Their enthalpies and melting points, either individually or in the composition of eutectics, are found by means of DSC. The entropies of fusion and the cryoscopic constants of individual compounds are calculated.

Kinetics of Melting and Dissolution in Lunar Materials

NASA Technical Reports Server (NTRS)

Hess, Paul C.

2002-01-01

An understanding of the petrogenesis of lunar magmas, particularly mare basalts and the parent magmas to the Mg-rich suite, remains an unfulfilled goal. The fact is not surprising given the complexity of the problem. On the Moon, the source region for lunar magmas is not primitive mantle but rather a series of cumulate rocks that vary widely in both minerology and major and minor element contents. The stratigraphy of the cumulate mantle is not likely to be very regular given that the culumate pile is formed initially in an unstable configuration and subsequent thermal and compositional heterogeneities on a number of length scales. These lithologic heterogeneities, the large range of pressures and temperatures over which melts are generated on the Moon, and the close juxtaposition of cumulate rock with widely varying solidii introduce significant complications to the nature of the melting relations that control melt generation. These factors, coupled with the likelihood that polybaric fractional melting of varying efficiencies ultimately control the composition of planetary progress, are ample reasons why the lunar magmas remain the enigma they are. To make progress, phase equilibria studies must be coupled with a detailed understanding of the time scales and the dynamics of crystal and melt reequilibration processes.

Containerless processing of glass forming melts in space

NASA Technical Reports Server (NTRS)

Day, D. E.; Ray, C. S.

1988-01-01

The near weightlessness of a material in the reduced gravity environment of space offers the opportunity of melting and cooling glass forming compositions without a container. This reduces the heterogeneous nucleation/crystallization which usually occurs at the walls of the container, thereby, extending the range of glass forming compositions. Based primarily on this idea, containerless glass forming experiments, which used a single axis acoustic levitator/furnace (SAAL), were conducted on SPAR rocket flights, 6 and 8, and on Space Shuttle mission, STS-7 and STS-61A. The experiments on the Space Shuttle were designed to include other studies related to melt homogenization and mixing, development of techniques for preparing uncontaminated preflight samples, and simple shaping experiments.

Melting relations in the Fe-rich portion of the system FeFeS at 30 kb pressure

USGS Publications Warehouse

Brett, R.; Bell, P.M.

1969-01-01

The melting relations of FeFeS mixtures covering the composition range from Fe to Fe67S33 have been determined at 30 kb pressure. The phase relations are similar to those at low pressure. The eutectic has a composition of Fe72.9S27.1 and a temperature of 990??C. Solubility of S in Fe at elevated temperatures at 30 kb is of the same order of magnitude as at low pressure. Sulfur may have significantly lowered the melting point of iron in the upper mantle during the period of coalescence of metal prior to core formation in the primitive earth. ?? 1969.

Constraints on Ureilite Petrogenesis and Carbon-Metal-Silicate Equilibria on the UPB

NASA Astrophysics Data System (ADS)

Goodrich, C. A.; Holloway, J. R.

1992-07-01

The most important constraints on models of ureilite petrogenesis are 1) Ureilites have lost a basaltic complement (they are ultramafic, extremely depleted in plagiophile elements, enriched in HREE, and have negative Eu anomalies and superchondritic Ca/Al ratios). 2) Ureilites experienced long equilibration times at high T (indicated by coarse grain size, extreme homogeneity of core crystals, correlations between olivine and pyroxene compositions, and metamorphic-like textures), followed by rapid cooling (indicated by structural features of pyroxene and narrow reduction rims on olivine). 3) Ureilites are probably residues (based on mass balance) but partly crystallized from melts. 4) Ureilites are derived from a minimum of six reservoirs that were distinct in oxygen isotopic composition and did not equilibrate with one another (this is consistent with the observation that olivine and pyroxene cores do not show correlations of mg with MnO, Cr2O3, Sm/Eu or Lu/Eu). 5) There is a correlation between oxygen isotopic composition and mg ratio in ureilites. Similar correlations are observed for Allende chondrules and group means of H3-L3-LL3 chondrites (Fig. 1), and are argued to result from nebular processes [1]. 6) If graphite-metal-silicate-CO/CO2 equilibrium was established during melting, then mg ratios of ureilites were determined by depth because CCO redox reactions are strongly pressure-dependent. Cohenite-bearing metallic spherule inclusions in the silicates and euhedral shapes of large graphite crystals in low-shock ureilites have been taken as evidence of equilibrium. Olivine reduction rims, highly variable interstitial metal compositions, and a lack of correlation between mg and metal content argue against equilibrium. 7) Ureilites either lost a low melting-T metal fraction or gained a refractory-rich metal component. (they have high abundances of siderophile elements but show fractionation between [Os, Ir, W, Re] and [Ni, Ga, Ge, Au]). 8) Primordial noble gases were retained in some carbon phases. 9) Ureilites formed at ~4.55 Ga but both Sm-Nd and Rb-Sr isotopic systematics have been subsequently disturbed. Constraints 1-4 are best met if ureilites are partial melt residues produced by ~25% equilibrium partial melting on an oxygen-isotopically heterogeneous parent body in >=6 distinct melting zones. If there was no global magma ocean, km-sized melting zones would not equilibrate oxygen with one another in 10 m.y. Constraints 5 and 6 appear difficult to reconcile. If the UPB inherited a nebular oxygen isotope-mg correlation how could this correlation have survived partial melting? If the melting zones all experienced approximately the same degree of melting (Mn/Mg, Cr/Mg, and HRE provide evidence for this), and silicate equilibria determined mg, then the original correlation may simply have shifted to higher mg, consistent with the position of the ureilite trend relative to the Allende trends (Fig. 1). However, if mg was depth-dependent then it is unlikely that any oxygen isotope-mg correlation would remain. Also, noble gases in carbon would be lost (violating constraint 8) during carbon redox reactions. All constraints would be better met if graphite-metal-silicate-CO/CO2 equilibrium was not established during partial melting. If graphite was primary but a CO/CO2 fluid phase was not present then there would have been no pressure/depth dependence of fO(sub)2. As long as the pressure was sufficiently high (~100-200 bars) to stabilize the most ferroan ureilite (Fo 76) then the more magnesian ureilites would have been stable in the presence of graphite and metal. On the other hand, constraints 7, 8, and 9 could be neatly met if most of the carbon was not primary but a carbon-metal-noble gas assemblage was added as a late component to the ultramafic rocks. The cohenite-bearing metallic spherules are rare and tiny (10-50 micrometers) compared to interstitial metal (mm-sized irregular grains). They appear to have been droplets of immiscible, hypereutectic Fe(Ni)-C liquids that were trapped by crystallizing silicates. In contrast, the interstitial metal and graphite show no evidence of having been a liquid Fe-C alloy and their confinement to grain boundaries and reduction rims is consistent with late addition. Goodrich and Berkley (2) argued that the spherules were carbon-saturated at 1200-1225 degrees C and therefore that the silicate liquid must have contained graphite. However, in the Fe-C system the stable graphite liquidus is much steeper than the metastable cohenite liquidus, and although these alloys were cohenite-saturated, they were not graphite-saturated. Hence, the silicate magma probably did not contain graphite and carbon was not the dominant control on fO(sub)2. Thus, it may be possible to reconcile the main constraints on ureilite petrogenesis without high pressures. [1] R.N. Clayton & T.K. Mayeda (1988] GCA 52, 1313. [2] C.A. Goodrich & J.L. Berkely (1986) GCA 50, 681.

Method for melting glass by measurement of non-bridging oxygen

DOEpatents

Jantzen, C.M.

1992-04-07

A method is described for making better quality molten glass in a glass melter, the glass having the desired viscosity and, preferably, also the desired resistivity so that the glass melt can be established effectively and the product of the glass melter will have the desired level of quality. The method includes the adjustment of the composition of the glass constituents that are fed into the melter in accordance with certain correlations that reliably predict the viscosity and resistivity from the melter temperature and the melt composition, then heating the ingredients to the melter's operating temperature until they melt and homogenize. The equations include the calculation of a non-bridging oxygen' term from the numbers of moles of the various ingredients, and then the determination of the viscosity and resistivity from the operating temperature of the melter and the non-bridging oxygen term. 4 figs.

A spectroscopic and computational study of Al(III) complexes in sodium cryolite melts: ionic composition in a wide range of cryolite ratios.

PubMed

Nazmutdinov, Renat R; Zinkicheva, Tamara T; Vassiliev, Sergey Yu; Glukhov, Dmitri V; Tsirlina, Galina A; Probst, Michael

2010-04-01

The structure of sodium cryolite melts was studied using Raman spectroscopy and quantum chemical calculations performed at the density functional theory level. The existence of bridged forms in the melts was argued first from the analysis of experimental Raman spectra. In the quantum chemical modelling emphasis was put on the construction of potential energy surfaces describing the formation/dissociation of certain complex species. Effects of the ionic environment were found to play a crucial role in the energetics of model processes. The structure of the simplest possible polymeric forms involving two Al centres linked through F atoms ("dimers") was thoroughly investigated. The calculated equilibrium constants and model Raman spectra yield additional evidence in favour of the dimers. This agrees with a self-consistent analysis of a series of Raman spectra for a wide range of the melt composition. Copyright 2010. Published by Elsevier B.V.

Apollo 16 impact-melt splashes - Petrography and major-element composition

NASA Technical Reports Server (NTRS)

See, Thomas H.; Horz, Friedrich; Morris, Richard V.

1986-01-01

Petrographic and major-element analyses are applied to 50 Apollo 16 impact-melt splash (IMS) samples in order to determine their origin and assess the nature of the subregolith source. The macroscopic analyses reveal that the IMSs exhibit a glassy appearance, but the textures range from holohyaline to hyalopilitic. Schlieren-rich glasses dominate the holohyaline areas, and the crystalline areas are mainly spherulitic. It is observed that most IMSs contain feldspathic monomineralic and lithic clasts and no regolithic materials. It is detected that the chemistry of most IMSs is not like the local regolith and appears to represent varied mixtures of VHA impact-melt breccias and anorthosite; the host rocks are mainly dimict breccias. It is concluded that the Cayley Formation is a polymict deposit composed of VHA impact-melt breccias and anorthosites. Tables revealing the macroscopic characteristics of the IMSs and the major-element composition of IMSs and various host rock are presented.

Reactive melt infiltration of silicon-molybdenum alloys into microporous carbon preforms

NASA Technical Reports Server (NTRS)

Singh, M.; Behrendt, D. R.

1995-01-01

Investigations on the reactive melt infiltration of silicon-1.7 and 3.2 at.% molybdenum alloys into microporous carbon preforms have been carried out by modeling, differential thermal analysis (DTA), and melt infiltration experiments. These results indicate that the pore volume fraction of the carbon preform is a very important parameter in determining the final composition of the reaction-formed silicon carbide and the secondary phases. Various undesirable melt infiltration results, e.g. choking-off, specimen cracking, silicon veins, and lake formation, and their correlation with inadequate preform properties are presented. The liquid silicon-carbon reaction exotherm temperatures are influenced by the pore and carbon particle size of the preform and the compositions of infiltrants. Room temperature flexural strength and fracture toughness of materials made by the silicon-3.2 at.% molybdenum alloy infiltration of medium pore size preforms are also discussed.

Segregation effects during solidification in weightless melts

NASA Technical Reports Server (NTRS)

Li, C.

1973-01-01

Two types of melt segregation effects were studied: (1) evaporative segregation, or segregation due to surface evaporation; and (2) freezing segregation, or segregation due to liquid-solid phase transformation. These segregation effects are closely related. In fact, evaporative segregation always precedes freezing segregation to some degree and must often be studied prior to performing meaningful solidification experiments. This is particularly true since evaporation may cause the melt composition, at least at the critical surface regions or layers to be affected manyfold within seconds so that the surface region or layer melting point and other thermophysical properties, nucleation characteristics, base for undercooling, and critical velocity to avoid constitutional supercooling, may be completely unexpected. An important objective was, therefore, to develop the necessary normal evaporation equations for predicting the compositional changes within specified times at temperature and to correlate these equations with actual experimental data collected from the literature.

Integrated Assessment and Improvement of the Quality Assurance System for the Cosworth Casting Process

NASA Astrophysics Data System (ADS)

Yousif, Dilon

The purpose of this study was to improve the Quality Assurance (QA) System at the Nemak Windsor Aluminum Plant (WAP). The project used Six Sigma method based on Define, Measure, Analyze, Improve, and Control (DMAIC). Analysis of in process melt at WAP was based on chemical, thermal, and mechanical testing. The control limits for the W319 Al Alloy were statistically recalculated using the composition measured under stable conditions. The "Chemistry Viewer" software was developed for statistical analysis of alloy composition. This software features the Silicon Equivalency (SiBQ) developed by the IRC. The Melt Sampling Device (MSD) was designed and evaluated at WAP to overcome traditional sampling limitations. The Thermal Analysis "Filters" software was developed for cooling curve analysis of the 3XX Al Alloy(s) using IRC techniques. The impact of low melting point impurities on the start of melting was evaluated using the Universal Metallurgical Simulator and Analyzer (UMSA).

Cogenetic Rock Fragments from a Lunar Soil: Evidence of a Ferroan Noritic-Anorthosite Pluton on the Moon

NASA Technical Reports Server (NTRS)

Jolliff, B. L.; Haskin, L. A.

1995-01-01

The impact that produced North Ray Crater, Apollo 16 landing site, exhumed rocks that include relatively mafic members of the lunar ferroan anorthositic suite. Bulk and mineral compositions indicate that a majority of 2-4 mm lithic fragments from sample 67513, including impact breccias and monomict igneous rocks, are related to a common noritic-anorthosite precursor. Compositions and geochemical trends of these lithic fragments and of related samples collected along the rim of North Ray Crater suggest that these rocks derived from a single igneous body. This body developed as an orthocumulate from a mixture of cumulus plagioclase and mafic intercumulus melt, after the plagioclase had separated from any cogenetic mafic minerals and had become concentrated into a crystal mush (approximately 70 wt% plagioclase, 30 wt% intercumulus melt). We present a model for the crystallization of the igneous system wherein "system" is defined as cumulus plagioclase and intercumulus melt. The initial accumulation of plagioclase is analogous to the formation of thick anorthosites of the terrestrial Stillwater Complex; however, a second stage of formation is indicated, involving migration of the cumulus-plagioclase-intercumulus-melt system to a higher crustal level, analogous to the emplacement of terrestrial massif anorthosites. Compositional variations of the lithic fragments from sample 67513 are consistent with dominantly equilibrium crystallization of intercumulus melt. The highly calcic nature of orthocumulus pyroxene and plagioclase suggests some reaction between the intercumulus melt and cumulus plagioclase, perhaps facilitated by some recrystallization of cumulus plagioclase. Bulk compositions and mineral assemblages of individual rock fragments also require that most of the mafic minerals fortned in close contact with cumulus plagioclase, not as separate layers. The distribution of compositions (and by inference, modes) has a narrow peak at anorthosite and a broader, larger peak at noritic anoilhosite. Characteristics of the samples and their geochemical trends imply an origin in a system that was large relative to the (unknown) size of the impact that produced the breccias of ferroan noritic-anorthosite composition that were excavated later by the formation of North Ray Crater, and they appear to be consistent with an origin of the suite within a perched plagioclase cumulate. If the Moon's crust formed by accumulation of plagioclase in a magma ocean, ferroan noritic anothosite, formed as an orthocumulate, is an alternative to extensive adcumulus formation of ferroan anorthosite (greater than 90 vol% plagiclase). This provides a relatively mafic ferroan anorthositic component (approximately 15 vol% mafics), which is required by mass-balance models of compositions of polymict lunar-crustal materials. The inferred bulk composition of the system of cumulus plagioclase and intercumulus melt is similar to that of ferroan regolith breccia MacAlpine Hills 88104/5, a lunar-highland meteorite, and may represent a common and widespread component of the Moon's early highland crust.

Thermal sprayed composite melt containment tubular component and method of making same

DOEpatents

Besser, Matthew F.; Terpstra, Robert L.; Sordelet, Daniel J.; Anderson, Iver E.

2002-03-19

A tubular thermal sprayed melt containment component for transient containment of molten metal or alloy wherein the tubular member includes a thermal sprayed inner melt-contacting layer for contacting molten metal or alloy to be processed, a thermal sprayed heat-generating layer deposited on the inner layer, and an optional thermal sprayed outer thermal insulating layer. The thermal sprayed heat-generating layer is inductively heated as a susceptor of an induction field or electrical resistively heated by passing electrical current therethrough. The tubular thermal sprayed melt containment component can comprise an elongated melt pour tube of a gas atomization apparatus where the melt pour tube supplies molten material from a crucible to an underlying melt atomization nozzle.

A preliminary study on isotopic evolution of ice by a melting experiment

NASA Astrophysics Data System (ADS)

Ham, J. Y.; Lee, J.; Lee, W. S.; Han, Y.; Hur, S. D.

2016-12-01

Evidences of melted snow at surface were found on some ice cores. Melted layers may generate a significant error when paleo-temperature was retrieved from ice cores using stable water isotopes. To resolve this problem, it is necessary to understand the isotopic changes of ice and its meltwater that is made during the ice and snow melting. Isotopic fractionations between liquid water and snow have been discussed by Taylor et al. (2002) and Lee et al. (2009). The goal of this work is to understand isotopic evolution of ice and its meltwater. Melting experiments in a cold room were designed and conducted with heat source (infrared lamp) to mimic solar radiation. Melting rates were calculated in terms of specific discharge (g/min). To control melting rates, distances between ice surface and heat source were adjusted in various conditions (1 cm, 10 cm and 20 cm). The experiments were conducted by three different melting rates, 1.6 g/min, 3.5 g/min and 5.8 g/min. We used cubic ice that has 3 cm in width, length and height in dimension with 1.5 kg or 2 kg of ice used totally. The total time spent melting the whole ice was 592, 783, and 1180 minutes, respectively. Cold room temperature was range of -1 to 1°C, which removes an effect of air temperature. Meltwater samples were collected and isotopic compositions of oxygen and hydrogen were determined by a cavity ring down spectrometer (Picarro L-1120) installed at the Korea Polar Research Institute. We also analyzed bulk water and bulk ice to make the ice used in the experiments (-8.20 ‰ and -58.73 ‰ for oxygen and hydrogen isotopes, respectively). The isotopic compositions of meltwater increased linearly or to a second degree polynomial. The isotopic variations were larger in the lower melting rates, compared to the higher melting rates (0.65 of lower melting rates vs. 0.35 higher melting rates for oxygen isotope). The slope of linear regression between oxygen and hydrogen ranged 6.2, 7.3 and 6.2, which is less than that of the Global Meteoric Water Line (8) and the sublimation (7.7) suggested by Earman et al. (2006). We believe that isotopic exchange between liquid water and ice plays a crucial role in the variations of isotopes for the ice and its meltwater. We will modify a physically based 1-D model used in the previous studies to better understand the isotopic compositions of ice and its meltwater.

Mantle Wedge formation during Subduction Initiation: evidence from the refertilized base of the Oman ophiolitic mantle

NASA Astrophysics Data System (ADS)

Prigent, C.; Guillot, S.; Agard, P.; Godard, M.; Lemarchand, D.; Ulrich, M.

2015-12-01

Although the Oman ophiolite is classically regarded as being the direct analog of oceanic lithosphere created at fast spreading ridges, the geodynamic context of its formation is still highly debated. The other alternative end-member model suggests that this ophiolite entirely formed in a supra-subduction zone setting. The latter one is supported by studies on volcanic sequences whereas studies dealing on the mantle section do not involve a significant influence of subduction processes on its structure and composition. We herein focus on basal peridotites from all along the ophiolite strike in order to decipher and characterize potential fluid/melt transfers relate to subduction processes. Samples were taken across the basal banded unit directly overlying the amphibolitic/granulitic metamorphic sole which represents an accreted part of the lower plate. We carried out a petrological, structural and geochemical study on these rocks and their constitutive minerals. Our results show that basal peridotites range from lherzolites to highly depleted harzburgites in composition. Clinopyroxenes (cpx) display melt impregnation textures and co-crystallized with HT/HP amphiboles (amph), spinels and sulfurs. Major and trace elements of the constitutive minerals indicate that these minerals represent trapped incremental partial melt after hydrous melting. Different cpx-bearing lithologies then result from varying degrees of partial melting and melt extraction. Combined with Boron isotopic data, we demonstrate that fluids responsible for hydrous melting of these ophiolitic basal peridotites are subduction-related, most likely derived from dehydration of the metamorphic sole during its formation in subduction initiation. From these observations and thermal constraints, we interpret the occurrence of these basal lherzolites as representing a freezing front developed by thermal re-equilibration (cooling) during subduction processes: subduction-related hydrous partial melts were extracted at different degrees until getting ultimately trapped, and crystallized cpx, amph and other associated minerals. If our interpretation is correct, the base of the Oman ophiolite could provide the best proxy for the composition of a frozen-in, incipiently forming mantle wedge.

A combined basalt and peridotite perspective on 14 million years of melt generation at the Atlantis Bank segment of the Southwest Indian Ridge: Evidence for temporal changes in mantle dynamics?

USGS Publications Warehouse

Coogan, L.A.; Thompson, G.M.; MacLeod, C.J.; Dick, H.J.B.; Edwards, S.J.; Hosford, Scheirer A.; Barry, T.L.

2004-01-01

Little is known about temporal variations in melt generation and extraction at midocean ridges largely due to the paucity of sampling along flow lines. Here we present new whole-rock major and trace element data, and mineral and glass major element data, for 71 basaltic samples (lavas and dykes) and 23 peridotites from the same ridge segment (the Atlantis Bank segment of the Southwest Indian Ridge). These samples span an age range of almost 14 My and, in combination with the large amount of published data from this area, allow temporal variations in melting processes to be investigated. Basalts show systematic changes in incompatible trace element ratios with the older samples (from ???8-14 Ma) having more depleted incompatible trace element ratios than the younger ones. There is, however, no corresponding change in peridotite compositions. Peridotites come from the top of the melting column, where the extent of melting is highest, suggesting that the maximum degree of melting did not change over this interval of time. New and published Nd isotopic ratios of basalts, dykes and gabbros from this segment suggest that the average source composition has been approximately constant over this time interval. These data are most readily explained by a model in which the average source composition and temperature have not changed over the last 14 My, but the dynamics of mantle flow (active-to-passive) or melt extraction (less-to-more efficient extraction from the 'wings' of the melting column) has changed significantly. This hypothesised change in mantle dynamics occurs at roughly the same time as a change from a period of detachment faulting to 'normal' crustal accretion. We speculate that active mantle flow may impart sufficient shear stress on the base of the lithosphere to rotate the regional stress field and promote the formation of low angle normal faults. ?? 2004 Elsevier B.V. All rights reserved.

Experience melting through the Earth's lower mantle via LH-DAC experiments on MgO-SiO2 and CaO-MgO-SiO2 systems

NASA Astrophysics Data System (ADS)

Baron, Marzena A.; Lord, Oliver T.; Walter, Michael J.; Trønnes, Reidar G.

2015-04-01

The large low shear-wave velocity provinces (LLSVPs) and ultra-low velocity zones (ULVZs) of the lowermost mantle [1] are likely characterized by distinct chemical compositions, combined with temperature anomalies. The heterogeneities may have originated by fractional crystallization of the magma ocean during the earliest history of the Earth [2,3] and/or the continued accretion at the CMB of subducted basaltic oceanic crust [4,5]. These structures and their properties control the distribution and magnitude of the heat flow at the CMB and therefore the convective dynamics and evolution of the whole Earth. To determine the properties of these structures and thus interpret the seismic results, a good understanding of the melting phase relations of relevant basaltic and peridotitic compositions are required throughout the mantle pressure range. The melting phase relations of lower mantle materials are only crudely known. Recent experiments on various natural peridotitic and basaltic compositions [6-8] have given wide ranges of solidus and liquidus temperatures at lower mantle pressures. The melting relations for MgO, MgSiO3 and compositions along the MgO-SiO2 join from ab initio theory [e.g. 9,10] is broadly consistent with a thermodynamic model for eutectic melt compositions through the lower mantle based on melting experiments in the MgO-SiO2 system at 16-26 GPa [3]. We have performed a systematic study of the melting phase relations of analogues for peridotitic mantle and subducted basaltic crust in simple binary and ternary systems that capture the major mineralogy of Earth's lower mantle, using the laser-heated diamond anvil cell (LH-DAC) technique at 25-100 GPa. We determined the eutectic melting temperatures involving the following liquidus mineral assemblages: 1. bridgmanite (bm) + periclase (pc) and bm + silica in the system MgO-SiO2 (MS), corresponding to model peridotite and basalt compositions 2. bm + pc + Ca-perovskite (cpv) and bm + silica + cpv in the system CaO-MgO-SiO2 (CMS). The eutectic melting temperatures (Te) were determined by multi-chamber DAC-experiments on near-eutectic compositions [3,9]. Ultra-fine W-powder mixed into the samples absorbed the laser energy. The samples were heated at a rate of 500-1500 K/min by increasing the laser power. More than 75-90% eutectic melt is produced at the the solidus, resulting in rapid aggregation of the W-powder and inefficient laser energy absorption. The resulting plateau in the temperature versus power curve is interpreted as Te. Our preliminary results show an expected positive p-Te correlation, with lower Te for the CMS-system. The dTe/dp slope for the bm-silica eutectic is lower than for the bm-pc eutectic in the MS-system. The experimental results agree with the DFT-studies and thermodynamic models. We have also developed a novel technique for micro-fabrication of metal-encapsulated samples (Re, W, Mo), to investigate more precisely the melting phase relations in the lower mantle pressure range. The metal-covered, 20 μm thick sample disc, placed between thermal insulation layers in the DAC, will be laser-heated at the two flat surfaces, providing low thermal gradients and preventing reaction between the sample and the pressure medium. [1] Lay and Garnero (2007, AGU Monograph); [2] Labrosse et al (2007, Nature); [3] Liebske and Frost (2012, EPSL); [4] Elkins-Tanton (2012, Ann Rev Earth Planet Sci); [5] Hirose et al (1999, Nature); [6] Fiquet et al (2010, Science); [7] Andrault et al (2011, EPSL); [8] Andrault et al (2014, Science); [9] de Koker et al (2013, EPSL); [10] de Koker and Strixrude (2009, Geophys J Int).

A Living Periodic Table.

ERIC Educational Resources Information Center

Marshall, James L.

2000-01-01

Introduces a portable and permanent set of the elemental collection including 87 samples of elements which are, minimum, one gram or more. Demonstrates radioactivity, magnetism, fluorescence, melting solids, spectral analysis, and conduction of heat. Includes a display of minerals associated with the elements. (YDS)

Ophiolite Perspectives on Oceanic Mantle Heterogeneity

NASA Astrophysics Data System (ADS)

Walker, R. J.; O'Driscoll, B.; Day, J. M.; Ash, R. D.; Daly, J. S.

2014-12-01

The mantle sections of ophiolites offer a useful approach to studying compositional heterogeneities in the oceanic mantle. A potential caveat is that the tectonic provenance of ophiolites is often not easy to decipher, although many have undergone at least supra-subduction zone (SSZ) processing. Significant outstanding questions include the degree to which ophiolite peridotites preserve evidence of pre-SSZ events and the way that SSZ melt extraction modifies the character of these peridotites. A suite of Caledonian ophiolites associated with the closure of the Iapetus Ocean offers an opportunity to shed light on these issues, in particular to assess the degree to which long (regional) wavelength compositional heterogeneities survive SSZ melting. Observations on the combined highly-siderophile element (HSE) and 187Os/188Os systematics of the broadly coetaneous (490-500 Ma) Shetland Ophiolite Complex (Scotland) and Leka Ophiolite Complex (LOC; Norway) are presented here. Generally, the lithological composition of each locality is harzburgitic, and hosts lenses and layers of dunite, chromitite and pyroxenite that are interpreted as representing SSZ-related (channelised) melt migration and melt-rock interaction. Although the bulk of the harzburgitic rocks have approximately chondritic initial 187Os/188Os and HSE abundances, ancient (Proterozoic) melt depletion (TRD =1.4 to 1 Ga) is recorded in ~10% of samples from each locality. This is also commonly observed in abyssal peridotites. One important implication of the data is that SSZ melt generation/migration has had no discernible impact on the bulk Os isotopic composition of the Iapetus oceanic mantle. By contrast, non-harzburgitic lithologies consistently exhibit more radiogenic initial 187Os/188Os and more variable HSE abundances. The dunites, chromitites and pyroxenites of the LOC can be separated into two groups on the basis of isochrons that they define; yielding ages of 481±22 Ma and 589±15 Ma, respectively. The former age corresponds, within error, to the accepted age of the ophiolite (497 ± 2 Ma). The meaning of the latter age is uncertain, but may correspond to the early stages of Iapetus opening. The data imply that the oceanic mantle represented by both ophiolites resembles a 'patchwork' of peridotites of different ages and compositions.

Evaluation of stability region for scandium-containing rare-earth garnet single crystals and their congruent-melting compositions

NASA Astrophysics Data System (ADS)

Kaurova, I. A.; Domoroshchina, E. N.; Kuz'micheva, G. M.; Rybakov, V. B.

2017-06-01

Single crystals of scandium-containing rare-earth garnets in system R-Sc-C-O (R3+=Y, Gd; C3+=Al, Ga) have been grown by the Czochralski technique. X-ray diffraction analysis has been used to refine crystal compositions. The fundamental difference between the melt compositions and compositions of grown crystals has been found (except for compositions of congruent-melting compounds, CMC). The specific features of garnet solid solution formation have been established and the ternary diagrams with real or hypothetical phases have been built. The dinamics of coordination polyhedra changes with the formation of substitutional solid solutions have been proposed based on the mathematical modeling and experimental data. Possible existence of CMC with garnet structure in different systems as well as limit content of Sc ions in dodecahedral and octahedral sites prior to their partial substitution of ions, located in other sites, have been evaluated. It was established that the redistribution of cations over crystallographic sites (antistructural point defects) due to system self-organization to maintain its stability may be accompanied by cation ordering and the symmetry change of individual polyhedrons and/or the whole crystal.

Mantle potential temperature estimates and primary melt compositions of the Low-Ti Emeishan flood basalt

NASA Astrophysics Data System (ADS)

Shellnutt, J. G.; Pham, Thuy T.

2018-05-01

The Late Permian Emeishan large igneous province (ELIP) is considered to be one of the best examples of a mantle plume derived large igneous province. One of the primary observations that favour a mantle plume regime is the presence of ultramafic volcanic rocks. The picrites suggest primary mantle melts erupted and that mantle potential temperatures (TP) of the ELIP were > 200oC above ambient mantle conditions. However, they may represent a mixture of liquid and cumulus olivine and pyroxene rather than primary liquids. Consequently, temperature estimates based on the picrite compositions may not be accurate. Here we calculate mantle potential temperature (TP) estimates and primary liquids compositions using PRIMELT3 for the low-Ti (Ti/Y < 500) Emeishan basalt as they represent definite liquid compositions. The calculated TP yield a range from 1400oC to 1550oC, which is consistent with variability across a mantle plume axis. The primary melt compositions of the basalts are mostly picritic. The results of this study indicate that the Emeishan basalt was produced by a high temperature regime and that a few of the ultramafic volcanic rocks may be indicative of primary liquids.

Fe-C-Si ternary composite coating on CP-titanium and its tribological properties

NASA Astrophysics Data System (ADS)

Maleque, M. A.; Saffina, W.; Ahmed, A. S.; Ali, M. Y.

2017-03-01

This study focused on the development of ternary composite coating through incorporation of Fe-C-Si ternary powder mixtures on CP-Ti substrate and characterizes the microstructure, hardness and wears behavior in presence of Jatropha oil. In this work, the surface of commercial purity titanium (CP-Ti) was modified using a tungsten inert gas (TIG) surface melting technique. The wear behavior of coated CP-titanium was performed using pin-on-disk machine. The results showed that the melt track has dendritic microstructure which was homogenously distributed throughout the melt pool. This Fe-C-Si ternary composite coating enhanced the surface hardness of CP-Ti significantly from 175 HV for the untreated substrate to ∼800 HV for the Fe-C-Si coated CP-Ti due to the formation of intermetallic compounds.. The wear results showed that less wear volume loss was observed on the composite coated CP-Ti in presence of Jatropha-biodiesel compared to uncoated CP-Ti. The achievement of this hard Fe-C-Si composite coating on the surface of CP-Ti can broadened new prospect for many engineering applications that use biodiesel under different tribological variables.

Constant average olivine Mg# in cratonic mantle reflects Archaean mantle melting to the exhaustion of orthopyroxene

NASA Astrophysics Data System (ADS)

Bernstein, S.; Kelemen, P. B.; Hanghoj, K.

2006-12-01

Shallow (garnet-free) cratonic mantle, occurring as xenoliths in kimberlites and alkaline basaltic lavas, has high Mg# (100x Mg/(Mg+Fe)>92) and is poor in Al and Ca compared to off-cratonic mantle. Many xenoliths show rhenium-depletion age of > 3 Ga, and are thus representative of depleted mantle peridotite that form an integral part of the stable nuclei of Archaean (2.5-3.8 Ga) cratons. Accordingly, the depleted composition of the xenolith suites is linked to Archaean melt extraction events. We have compiled data for many suites of shallow cratonic mantle xenoliths worldwide, including samples from cratons of Kaapvaal, Tanzania, Siberia, Slave, North China and Greenland, and encompassing both the classic orthopyroxene-rich peridotites of Kaapvaal and orthopyroxene-poor peridotites from Greenland. The suites show a remarkably small range in average olivine Mg# of 92.8 +/- 0.2. Via comparison with data for experimental melting of mantle peridotite compositions, we explain consistent olivine Mg# in the shallow cratonic mantle as the result of mantle melting and melt extraction to the point of orthopyroxene exhaustion, leaving a nearly monomineralic olivine, or dunitic, residue. Experimental data for peridotite melting at pressures less than 4 GPa and data on natural rocks suggest that mantle olivine has a Mg# of about 92.8 at the point of orthopyroxene exhaustion. If the melt extraction was efficient, no further melting could take place without a considerable temperature increase or melt/fluid flux through the dunite residue at high temperatures. While the high Mg#, dunite-dominated xenolith suites from e.g. Greenland represent simple residues from mantle melting, the orthopyroxene-rich xenolith suites with identical Mg# as known from e. g. Kaapvaal must reflect some additional processes. We envisage their derivation from dunite protoliths via subsequent melt/rock reaction with silica-rich melts or, in some cases, possibly as residues at higher average melting pressures.

Hf isotope evidence for effective impact melt homogenisation at the Sudbury impact crater, Ontario, Canada

NASA Astrophysics Data System (ADS)

Kenny, Gavin G.; Petrus, Joseph A.; Whitehouse, Martin J.; Daly, J. Stephen; Kamber, Balz S.

2017-10-01

We report on the first zircon hafnium-oxygen isotope and trace element study of a transect through one of the largest terrestrial impact melt sheets. The differentiated melt sheet at the 1.85 Ga, originally ca. 200 km in diameter Sudbury impact crater, Ontario, Canada, yields a tight range of uniform zircon Hf isotope compositions (εHf(1850) of ca. -9 to -12). This is consistent with its well-established crustal origin and indicates differentiation from a single melt that was initially efficiently homogenised. We propose that the heterogeneity in other isotopic systems, such as Pb, in early-emplaced impact melt at Sudbury is associated with volatility-related depletion during the impact cratering process. This depletion leaves the isotopic systems of more volatile elements more susceptible to contamination during post-impact assimilation of country rock, whereas the systems of more refractory elements preserve initial homogeneities. Zircon oxygen isotope compositions in the melt sheet are also restricted in range relative to those in the impacted target rocks. However, they display a marked offset approximately one-third up the melt sheet stratigraphy that is interpreted to be a result of post-impact assimilation of 18O-enirched rocks into the base of the cooling impact melt. Given that impact cratering was a more dominant process in the early history of the inner Solar System than it is today, and the possibility that impact melt sheets were sources of ex situ Hadean zircon grains, these findings may have significance for the interpretation of the early zircon Hf record. We speculate that apparent εHf-time arrays observed in the oldest terrestrial and lunar zircon datasets may be related to impact melting homogenising previously more diverse crust. We also show that spatially restricted partial melting of rocks buried beneath the superheated impact melt at Sudbury provided a zircon crystallising environment distinct to the impact melt sheet itself.

Melt Compositional Diversities in Early Ignimbrite from the 2.08 Ma Huckleberry Ridge Eruption, Yellowstone

NASA Astrophysics Data System (ADS)

Swallow, E. J.; Wilson, C. J. N.; Myers, M.; Collins, K. S.

2016-12-01

Detailed, stratigraphically-constrained geochemical analyses can shed light on the nature of magma systems and mechanisms behind the initiation and escalation of large caldera-forming eruptions1,2. The 2.08 Ma, ˜2,500 km3 Huckleberry Ridge Tuff is the first of three caldera-forming eruptions in the Yellowstone area3, and consists of a widespread initial fall deposit3,4 followed by three ignimbrite members3: A, B and C. Myers et al.2 demonstrated the episodic and multi-vent initiation of the HRT event during eruption of the initial fall deposits, with sequential tapping of three discrete melt bodies, the last of which becomes dominant within the later fall deposits. Here, we build on their dataset to consider glass compositions in the earliest-erupted parts of the overlying ignimbrite (member A). Trace element analyses of ignimbrite shards reveals clustering of compositions and signifies a continuation of the tapping of multiple melt domains. Principal component and cluster analysis indicate at least seven clusters, separated out by crystal fractionation processes. These early flows tapped a range of melts (paralleled by whole-rock magma compositions), from highly evolved (as in the fall deposits) to hotter, less evolved material not represented in the fall deposits. Variations are greatest in Ba (10-900 ppm), Rb/Sr ratios (10-210) and degrees of LREE depletion. However there is an absence of geographical variation, with locations north and south of the subsequent caldera, and in proximal and distal regions, exhibiting similar ranges of glass composition from inferred contemporaneous flow deposition. These observations suggest complexities in the early stages of the tapping of a heterogeneous magma chamber (comprising multiple melt/magma domains), possibly accompanying the onset of caldera collapse. We also consider that external controls, such as rifting, were at least initially important as an eruption trigger2 but understanding of the mechanisms controlling the onset of ignimbrite generation is complicated by the apparent lack of a compositionally coherent melt-dominant magma body. 1Pistolesi et al. (2016): Geology 44, 487-490; 2Myers et al. (2016): Earth Planet Sci Lett (in press); 3Christiansen (2001): USGS Prof Paper 729-G; 4Izett & Wilcox (1982), USGS Map I-1325.

Materials science research in microgravity

NASA Technical Reports Server (NTRS)

Perepezko, John H.

1992-01-01

There are several important attributes of an extended duration microgravity environment that offer a new dimension in the control of the microstructure, processing, and properties of materials. First, when gravitational effects are minimized, buoyancy driven convection flows are also minimized. The flows due to density differences, brought about either by composition or temperature gradients will then be reduced or eliminated to permit a more precise control of the temperature and the composition of a melt which is critical in achieving high quality crystal growth of electronic materials or alloy structures. Secondly, body force effects such as sedimentation, hydrostatic pressure, and deformation are similarly reduced. These effects may interfere with attempts to produce uniformly dispersed or aligned second phases during melt solidification. Thirdly, operating in a microgravity environment will facilitate the containerless processing of melts to eliminate the limitations of containment for reactive melts. The noncontacting forces such as those developed from electromagnet, electrostatic, or acoustic fields can be used to position samples. With this mode of operation, contamination can be minimized to enable the study of reactive melts and to eliminate extraneous crystal nucleation so that novel crystalline structures and new glass compositions may be produced. In order to take advantage of the microgravity environment for materials research, it has become clear that reliable processing models based on a sound ground based experimental experience and an established thermophysical property data base are essential.

Experimental Behavior of Sulfur Under Primitive Planetary Differentiation Processes, the Sulfide Formations in Enstatite Meteorites and Implications for Mercury.

NASA Technical Reports Server (NTRS)

Malavergne, V.; Brunet, F.; Righter, K.; Zanda, B.; Avril, C.; Borensztajn, S.; Berthet, S.

2012-01-01

Enstatite meteorites are the most reduced naturally-occuring materials of the solar system. The cubic monosulfide series with the general formula (Mg,Mn,Ca,Fe)S are common phases in these meteorite groups. The importance of such minerals, their formation, composition and textural relationships for understanding the genesis of enstatite chondrites (EC) and aubrites, has long been recognized (e.g. [1]). However, the mechanisms of formation of these sulfides is still not well constrained certainly because of possible multiple ways to produce them. We propose to simulate different models of formation in order to check their mineralogical, chemical and textural relevancies. The solubility of sulfur in silicate melts is of primary interest for planetary mantles, particularly for the Earth and Mercury. Indeed, these two planets could have formed, at least partly, from EC materials (e.g. [2, 3, 4]). The sulfur content in silicate melts depends on the melt composition but also on pressure (P), temperature (T) and oxygen fugacity fO2. Unfortunately, there is no model of general validity in a wide range of P-T-fO2-composition which describes precisely the evolution of sulfur content in silicate melts, even if the main trends are now known. The second goal of this study is to constrain the sulfur content in silicate melts under reducing conditions and different temperatures.

Constraints on the Parental Melts of Enriched Shergottites from Image Analysis and High Pressure Experiments

NASA Technical Reports Server (NTRS)

Collinet, M.; Medard, E.; Devouard, B.; Peslier, A.

2012-01-01

Martian basalts can be classified in at least two geochemically different families: enriched and depleted shergottites. Enriched shergottites are characterized by higher incompatible element concentrations and initial Sr-87/Sr-86 and lower initial Nd-143/Nd-144 and Hf-176/Hf-177 than depleted shergottites [e.g. 1, 2]. It is now generally admitted that shergottites result from the melting of at least two distinct mantle reservoirs [e.g. 2, 3]. Some of the olivine-phyric shergottites (either depleted or enriched), the most magnesian Martian basalts, could represent primitive melts, which are of considerable interest to constrain mantle sources. Two depleted olivine-phyric shergottites, Yamato (Y) 980459 and Northwest Africa (NWA) 5789, are in equilibrium with their most magnesian olivine (Fig. 1) and their bulk rock compositions are inferred to represent primitive melts [4, 5]. Larkman Nunatak (LAR) 06319 [3, 6, 7] and NWA 1068 [8], the most magnesian enriched basalts, have bulk Mg# that are too high to be in equilibrium with their olivine megacryst cores. Parental melt compositions have been estimated by subtracting the most magnesian olivine from the bulk rock composition, assuming that olivine megacrysts have partially accumulated [3, 9]. However, because this technique does not account for the actual petrography of these meteorites, we used image analysis to study these rocks history, reconstruct their parent magma and understand the nature of olivine megacrysts.

The Effects of Annealing Temperatures on Composition and Strain in SixGe1−x Obtained by Melting Growth of Electrodeposited Ge on Si (100)

PubMed Central

Abidin, Mastura Shafinaz Zainal; Morshed, Tahsin; Chikita, Hironori; Kinoshita, Yuki; Muta, Shunpei; Anisuzzaman, Mohammad; Park, Jong-Hyeok; Matsumura, Ryo; Mahmood, Mohamad Rusop; Sadoh, Taizoh; Hashim, Abdul Manaf

2014-01-01

The effects of annealing temperatures on composition and strain in SixGe1−x, obtained by rapid melting growth of electrodeposited Ge on Si (100) substrate were investigated. Here, a rapid melting process was performed at temperatures of 1000, 1050 and 1100°C for 1 s. All annealed samples show single crystalline structure in (100) orientation. A significant appearance of Si-Ge vibration mode peak at ~00 cm−1 confirms the existence of Si-Ge intermixing due to out-diffusion of Si into Ge region. On a rapid melting process, Ge melts and reaches the thermal equilibrium in short time. Si at Ge/Si interface begins to dissolve once in contact with the molten Ge to produce Si-Ge intermixing. The Si fraction in Si-Ge intermixing was calculated by taking into account the intensity ratio of Ge-Ge and Si-Ge vibration mode peaks and was found to increase with the annealing temperatures. It is found that the strain turns from tensile to compressive as the annealing temperature increases. The Si fraction dependent thermal expansion coefficient of SixGe1−x is a possible cause to generate such strain behavior. The understanding of compositional and strain characteristics is important in Ge/Si heterostructure as these properties seem to give significant effects in device performance. PMID:28788521

The Effects of Annealing Temperatures on Composition and Strain in Si x Ge1-x Obtained by Melting Growth of Electrodeposited Ge on Si (100).

PubMed

Abidin, Mastura Shafinaz Zainal; Morshed, Tahsin; Chikita, Hironori; Kinoshita, Yuki; Muta, Shunpei; Anisuzzaman, Mohammad; Park, Jong-Hyeok; Matsumura, Ryo; Mahmood, Mohamad Rusop; Sadoh, Taizoh; Hashim, Abdul Manaf

2014-02-24

The effects of annealing temperatures on composition and strain in Si x Ge 1- x , obtained by rapid melting growth of electrodeposited Ge on Si (100) substrate were investigated. Here, a rapid melting process was performed at temperatures of 1000, 1050 and 1100 °C for 1 s. All annealed samples show single crystalline structure in (100) orientation. A significant appearance of Si-Ge vibration mode peak at ~400 cm -1 confirms the existence of Si-Ge intermixing due to out-diffusion of Si into Ge region. On a rapid melting process, Ge melts and reaches the thermal equilibrium in short time. Si at Ge/Si interface begins to dissolve once in contact with the molten Ge to produce Si-Ge intermixing. The Si fraction in Si-Ge intermixing was calculated by taking into account the intensity ratio of Ge-Ge and Si-Ge vibration mode peaks and was found to increase with the annealing temperatures. It is found that the strain turns from tensile to compressive as the annealing temperature increases. The Si fraction dependent thermal expansion coefficient of Si x Ge 1- x is a possible cause to generate such strain behavior. The understanding of compositional and strain characteristics is important in Ge/Si heterostructure as these properties seem to give significant effects in device performance.

Effect of composition in the development of carbamazepine hot-melt extruded solid dispersions by application of mixture experimental design.

PubMed

Djuris, Jelena; Ioannis, Nikolakakis; Ibric, Svetlana; Djuric, Zorica; Kachrimanis, Kyriakos

2014-02-01

This study investigates the application of hot-melt extrusion for the formulation of carbamazepine (CBZ) solid dispersions, using polyethyleneglycol-polyvinyl caprolactam-polyvinyl acetate grafted copolymer (Soluplus, BASF, Germany) and polyoxyethylene-polyoxypropylene block copolymer (Poloxamer 407). In agreement with the current Quality by Design principle, formulations of solid dispersions were prepared according to a D-optimal mixture experimental design, and the influence of formulation composition on the properties of the dispersions (CBZ heat of fusion and release rate) was estimated. Prepared solid dispersions were characterized using differential scanning calorimetry, attenuated total reflectance infrared spectroscopy and hot stage microscopy, as well as by determination of the dissolution rate of CBZ from the hot-melt extrudates. Solid dispersions of CBZ can be successfully prepared using the novel copolymer Soluplus. Inclusion of Poloxamer 407 as a plasticizer facilitated the processing and decreased the hardness of hot-melt extrudates. Regardless of their composition, all hot-melt extrudates displayed an improvement in the release rate compared to the pure CBZ, with formulations having the ratio of CBZ : Poloxamer 407 = 1 : 1 showing the highest increase in CBZ release rate. Interactions between the mixture components (CBZ and polymers), or quadratic effects of the components, play a significant role in overall influence on the CBZ release rate. © 2013 Royal Pharmaceutical Society.

Modeling the Thermostructural Stability of Melt-infiltrated Sic/sic Composites

NASA Technical Reports Server (NTRS)

DiCarlo, James A.; Bhatt, Ramakrishna T.; McCue, Terry R.

2003-01-01

SiC/SiC composites developed by NASA with Sylramic-iBN fibers and melt-infiltrated (MI) SiC-Si matrices have demonstrated 1000-hour rupture life in air at 100 MPa and 1315OC. Recently it has been determined that a major factor controlling the long-term rupture life of these composites is not environment or stress, but an intrinsic microstructural and strength instability caused by a thermally-induced silicon attack of the Sic fibers. The objective of this paper is to present a simple diffusion-based analytical model which predicts well the observed effects of stress-free thermal exposure on the residual tensile strength of Sylramic-iBN/SiC-Si composites. The practical implications of the model for SiC/SiC composites with MI matrices are discussed.

Apatite: A New Tool For Understanding The Temporal Variability Of Magmatic Volatile Contents

NASA Astrophysics Data System (ADS)

Stock, M. J.; Humphreys, M.; Smith, V.; Pyle, D. M.; Isaia, R.

2015-12-01

The apatite crystal structure is capable of incorporating H2O, F and Cl, as well as trace CO2 and sulphur. These can be related to parental magma compositions through application of a series of pressure and temperature-dependent exchange reactions (Piccoli and Candela, 1994), permitting apatite crystals to preserve a record of all major volatile species in the melt. Furthermore, due to the general incompatibility of P in other rock-forming minerals, apatite is ubiquitous in igneous systems and often begins crystallising early, such that apatite inclusions within phenocrysts record melt volatile contents throughout magmatic differentiation. In this work, we compare the compositions of apatite inclusions and microphenocrysts with pyroxene-hosted melt inclusions from the Astroni 1 eruption of Campi Flegrei, Italy. These data are coupled with magmatic differentiation models (Gualda et al., 2012), experimental volatile solubility data (Webster et al., 2014) and thermodynamic models of apatite compositional variations (Piccoli and Candela, 1994) to determine a time-series of magmatic volatile evolution in the build-up to eruption. We find that apatite halogen/OH ratios decreased through magmatic differentiation, while melt inclusion F and Cl concentrations increased. Melt inclusion H2O contents are constant at ~2.5 wt%. These data are best explained by volatile-undersaturated differentiation over most of the crystallisation history of the Astroni 1 melt, with melt inclusion H2O contents reset during ascent, due to rapid H diffusion through the phenocryst hosts (Woods et al., 2000). Given the rapid diffusivity of volatiles in apatite (Brenan, 1993), preservation of undersaturated compositions in microphenocrysts suggests that saturation was only achieved a few days to months before eruption and that it may have been the transition into a volatile-saturated state that ultimately triggered eruption. Piccoli and Candela, 1994. Am. J. of Sc., 294, 92-135. Gualda et al., 2012. J. Pet., 53, 875-890. Webster et al., 2014. J. Pet., 55, 2217-2248. Woods et al., 2000. Am. Min., 85, 480-487. Brenan, 1993. Chem. Geol., 110, 195-210.

Maruyamaite, a new K-dominant tourmaline coexisting with diamond -an important accessory mineral in UHP rocks

NASA Astrophysics Data System (ADS)

Stock, M. J.; Humphreys, M.; Smith, V.; Pyle, D. M.; Isaia, R.

2014-12-01

The apatite crystal structure is capable of incorporating H2O, F and Cl, as well as trace CO2 and sulphur. These can be related to parental magma compositions through application of a series of pressure and temperature-dependent exchange reactions (Piccoli and Candela, 1994), permitting apatite crystals to preserve a record of all major volatile species in the melt. Furthermore, due to the general incompatibility of P in other rock-forming minerals, apatite is ubiquitous in igneous systems and often begins crystallising early, such that apatite inclusions within phenocrysts record melt volatile contents throughout magmatic differentiation. In this work, we compare the compositions of apatite inclusions and microphenocrysts with pyroxene-hosted melt inclusions from the Astroni 1 eruption of Campi Flegrei, Italy. These data are coupled with magmatic differentiation models (Gualda et al., 2012), experimental volatile solubility data (Webster et al., 2014) and thermodynamic models of apatite compositional variations (Piccoli and Candela, 1994) to determine a time-series of magmatic volatile evolution in the build-up to eruption. We find that apatite halogen/OH ratios decreased through magmatic differentiation, while melt inclusion F and Cl concentrations increased. Melt inclusion H2O contents are constant at ~2.5 wt%. These data are best explained by volatile-undersaturated differentiation over most of the crystallisation history of the Astroni 1 melt, with melt inclusion H2O contents reset during ascent, due to rapid H diffusion through the phenocryst hosts (Woods et al., 2000). Given the rapid diffusivity of volatiles in apatite (Brenan, 1993), preservation of undersaturated compositions in microphenocrysts suggests that saturation was only achieved a few days to months before eruption and that it may have been the transition into a volatile-saturated state that ultimately triggered eruption. Piccoli and Candela, 1994. Am. J. of Sc., 294, 92-135. Gualda et al., 2012. J. Pet., 53, 875-890. Webster et al., 2014. J. Pet., 55, 2217-2248. Woods et al., 2000. Am. Min., 85, 480-487. Brenan, 1993. Chem. Geol., 110, 195-210.

Temperature Dependence of Electrical Resistance of Woven Melt-Infiltrated SiCf/SiC Ceramic Matrix Composites

NASA Technical Reports Server (NTRS)

Appleby, Matthew P.; Morscher, Gregory N.; Zhu, Dongming

2016-01-01

Recent studies have successfully shown the use of electrical resistance (ER)measurements to monitor room temperature damage accumulation in SiC fiber reinforced SiC matrix composites (SiCf/SiC) Ceramic Matrix Composites (CMCs). In order to determine the feasibility of resistance monitoring at elevated temperatures, the present work investigates the temperature dependent electrical response of various MI (Melt Infiltrated)-CVI (Chemical Vapor Infiltrated) SiC/SiC composites containing Hi-Nicalon Type S, Tyranno ZMI and SA reinforcing fibers. Test were conducted using a commercially available isothermal testing apparatus as well as a novel, laser-based heating approach developed to more accurately simulate thermomechanical testing of CMCs. Secondly, a post-test inspection technique is demonstrated to show the effect of high-temperature exposure on electrical properties. Analysis was performed to determine the respective contribution of the fiber and matrix to the overall composite conductivity at elevated temperatures. It was concluded that because the silicon-rich matrix material dominates the electrical response at high temperature, ER monitoring would continue to be a feasible method for monitoring stress dependent matrix cracking of melt-infiltrated SiC/SiC composites under high temperature mechanical testing conditions. Finally, the effect of thermal gradients generated during localized heating of tensile coupons on overall electrical response of the composite is determined.

Studies of thermal dissolution of RDX in TNT melt

NASA Astrophysics Data System (ADS)

Suvorova, N. A.; Hamilton, V. T.; Oschwald, D. M.; Balakirev, F. F.; Smilowitz, L. B.; Henson, B. F.

2017-01-01

The thermal response of energetic materials is studied due to its importance in issues of material safety and surety. Secondary high explosives which melt before they thermally decompose present challenging systems to model due to the addition of material flow. Composition B is a particularly challenging system due to its multiphase nature with a low melt component (TNT) and a high melt component (RDX). The dissolution of RDX crystals in molten TNT at the temperature below RDX melting point has been investigated using hot stage microscopy. In this paper, we present data on the dissolution rate of RDX crystals in molten TNT as a function of temperature above the TNT melt.

Partial melting of the Allende (CV3) meteorite - Implications for origins of basaltic meteorites

NASA Technical Reports Server (NTRS)

Jurewicz, A. J. G.; Mittlefehldt, D. W.; Jones, J. H.

1991-01-01

Eucrites and angrites are distinct types of basaltic meteorites whose origins are poorly known. Experiments in which samples of the Allende (CV3) carbonaceous chondrite were partially melted indicate that partial melts can resemble either eucrites or angrites, depending only on the oxygen fugacity. Melts are eucritic if this variable is below that of the iron-wuestite buffer or angritic if above it. With changing pressure, the graphite-oxygen redox reaction can produce oxygen fugacities that are above or below those of the iron-wuestite buffer. Therefore, a single, homogeneous, carbonaceous planetoid greater than 110 kilometers in radius could produce melts of drastically different composition, depending on the depth of melting.

Thermoplastic/Nanotube Composite Fibers

NASA Astrophysics Data System (ADS)

Haggenmueller, Reto; Fischer, John; Winey, Karen

2000-03-01

A combination of solvent casting and melt mixing methods are used to compound selected thermoplastics with single-wall carbon nanotubes. Subsequently, melt extrusion is used to form thermoplastic-nanotube composite fibers. The structural characteristics are investigated by electron microscopy and x-ray scattering methods. In addition the electrical, thermal and mechanical properties were measured. Correlations are sought between the viscoelastic properties of the compounded materials, the nanotube loading and elongation ratio after spinning, and the properties of the resultant fibers.

Petrologic constraints on the surface processes on asteroid 4 Vesta and on excavation depths of diogenite fragments

NASA Technical Reports Server (NTRS)

Grove, T. L.

1993-01-01

The eucrite-howardite-diogenite meteorite groups are though to be related by magmatic processes. Asteroid 4 Vesta has been proposed as the parent body for these basaltic achondrite meteorites. The similarity of the planetesimal's surface composition to eucrite and diogenite meteorites and the large size of the asteroid (r = 250 km) make it an attractive source, but its position in the asteroid belt far from the known resonances from which meteorites originate make a relation between Vesta and eucrite-howardite-giogenite group problematic. It has been proposed that diogenites are low-Ca pyroxene-rich cumulates that crystallized from a magnesian parent (identified in howardite breccias), and this crystallization process led to evolved eucrite derivative magmas. This eucrite-diogenite genetic relationship places constraints on the physical conditions under which crystallization occurred. Elevated pressure melting experiments on magnesian eucrite parent compositions show that the minimum pressure at which pyroxene crystallization could lead to the observed compositions of main series eucrites is 500 bars, equivalent to a depth of 135 km in a 4 Vesta-sized eucrite parent body. Therefore, the observation of diogenite on the surface of 4 Vesta requires a post-crystallization process that excavates diogenite cumulate from depth. The discovery of diogenite asteroidal fragments is consistent with an impact event on 4 Vesta that penetrated the deep interior of this planetesimal.

Experimental and Petrological Constraints on Lunar Differentiation from the Apollo 15 Green Picritic Glasses

NASA Technical Reports Server (NTRS)

Elkins-Tanton, Linda T.; Chatterjee, Nilanjan; Grove, Timothy L.

2003-01-01

Phase equilibrium experiments on the most magnesian Apollo 15C green picritic glass composition indicate a multiple saturation point with olivine and orthopyroxene at 1520 C and 1.3 GPa (about 260 km depth in the moon). This composition has the highest Mg# of any lunar picritic glass and the shallowest multiple saturation point. Experiments on an Apollo 15A composition indicate a multiple saturation point with olivine and orthopyroxene at 1520 C and 2.2 GPa (about 440 km depth in the moon). The importance of the distinctive compositional trends of the Apollo 15 groups A, B, and C picritic glasses merits the reanalysis of NASA slide 15426,72 with modern electron microprobe techniques. We confirm the compositional trends reported by Delano (1979, 1986) in the major element oxides SiO2, TiO2, Al2O3, Cr2O3, FeO, MnO, MgO, and CaO, and we also obtained data for the trace elements P2O5, K2O, Na2O, NiO, S, Cu, Cl, Zn, and F. Petrogenetic modeling demonstrates that the Apollo 15 A-B-C glass trends could not have been formed by fractional crystallization or any continuous assimilation/fractional crystallization (AFC) process. The B and C glass compositional trends could not have been formed by batch or incremental melting of an olivine + orthopyroxene source or any other homogeneous source, though the A glasses may have been formed by congruent melting over a small pressure range at depth. The B compositional trend is well modeled by starting with an intermediate A composition and assimilating a shallower, melted cumulate, and the C compositional trend is well modeled by a second assimilation event. The assimilation process envisioned is one in which heat and mass transfer were separated in space and time. In an initial intrusive event, a picritic magma crystallized and provided heat to melt magma ocean cumulates. In a later replenishment event, the picritic magma incrementally mixed with the melted cumulate (creating the compositional trends in the green glass data set), ascended to the lunar surface, and erupted as a fire fountain. A barometer created from multiple saturation points provides a depth estimate of other glasses in the A-B-C trend and of the depths of assimilation. This barometer demonstrates that the Apollo 15 A-B-C trend originated over a depth range of approx.460 km to approx.260 km within the moon.

Apatite-hosted melt inclusions in Damiao massif anorthosite complex, North China

NASA Astrophysics Data System (ADS)

Wang, M.; Veksler, I. V.; Zhang, Z.

2014-12-01

Models for the nelsonite formation are currently highly contentious, with liquid immiscibility and fractional crystallization as frequently proposed formation mechanisms. The nelsonites in the Damiao massif anorthosite complex in the North China Craton and experimental evidence are revisited for the existence of silica-free CaO-FeO-Fe2O3-TiO2-P2O5 immiscible nelsonitic liquids. Our results of differential scanning calorimetry (DSC) demonstrate that nelsonite with the composition of one-third apatite and two-thirds Fe-Ti oxides by weight completely melts well above 1450 ºC, which is in good agreement with numerous experimental studies of the CaO-P2O5-FexO system in connection to metallurgy. Thus, the composition cannot be molten at temperatures relevant for crystallization of the Damiao magma. A review of experimental studies of liquid immiscibility and analyses of natural immiscible glasses show that all the liquids on the Fe- and P-rich side of the miscibility gap have at least 20 wt. % of aluminosilicate components. Main results of this study come from the analyses of apatite-hosted melt inclusions in Damiao nelsonite. The inclusions range from ~3 to 200 μm in diameter. They are ubiquitous and meet all the morphological criteria of primary melt inclusions crystallised into assemblages of daughter minerals. Almost all of them contain vermiculite and chlorite, and some contain biotite, amphibole, phlogopite and Fe-Ti oxides. Out of dozens analysed inclusions, only three have high contents of SiO2 (62.1-73.8 wt. %) and low contents of FeO (0.25-2.35 wt. %). Bulk compositions of other inclusions show large variations in SiO2 (20.79-50.16 wt. %) and FeOt (13.44-32.78 wt. %). With a few exceptions, the inclusions are very low in CaO (0.04-1.51 wt. %, and high in Al2O3 (10-21.17 wt. %). Despite the high Fe content, the compositions differ from those of the typical immiscible Fe-rich melts. It appears that the cumulus apatite crystallised from Fe-rich, hydrated silicate melt. We propose that the inclusions at Damiao record a trend of intercumulus melt evolution, which was strongly affected by separation of a hydrothermal fluid phase and the losses of alkali and Ca silicate components from the melt into the fluid.

A Little Island With A Big Secret: Isla Rábida, Galápagos

NASA Astrophysics Data System (ADS)

Bercovici, H.; Geist, D.; Harpp, K. S.; Almeida, M.; Mahr, J.; Pimentel, R.; Cleary, Z.

2016-12-01

The Galápagos Archipelago is a hotspot island chain 1000 km west of Ecuador, where the vast majority of the lavas are basaltic. Four volcanoes in the archipelago, Rábida, Santiago, Pinzón, and Alcedo, erupt rhyolites and trachytes. Isla Rábida, a small island 50 km east of the mantle plume center, is the focus of this project. It is 5 km2 in area, and lavas range from 0.9 to 1.1 Ma. About 25% of the rocks in our suite are intermediate to felsic, extending from Mg#=2 to 57. Major and trace element data indicate the evolved rocks formed by advanced crystallization of basaltic magma. One of the unique aspects of Rábida is the cumulate xenolith suite ranging from olivine gabbro to ferroan granite. The basalts have 6 to 58 modal% plagioclase phenocrysts, which we interpret as mixtures of melt and accumulated plagioclase mush at the margins of the shallow reservoir. Thus, Rábida erupts material that has undergone different extents of crystallization and crystal sorting from pure melts, to melt-mush hybrids, to solidified cumulates. This hypothesis is evaluated by comparing plagioclase compositions from the xenoliths and the lavas. Plagioclases in two of the lavas, one with Mg#=57 and the other with Mg#=36, have similar compositions and zonation patterns to each other. There is on average less than 4% change in anorthite content from the core of the plagioclases in the basalts to the rim, with the compositions overall varying between An22 and An37. Both melts likely picked up the crystals from the same plagioclase mush before eruption. In comparison to plagioclases in an olivine-gabbro xenolith from Rábida, those in the lavas are less zoned, suggesting that the lavas' plagioclases experienced a different growth environment. Plagioclases in the xenolith are normally zoned, with cores averaging An37 and rims averaging An32. The xenolith's plagioclases also have more diverse compositions than those in the lavas. The normal zoning in the xenolith's plagioclase is likely from late-stage crystallization of evolved intercumulus melt. Our results suggest that the extraordinary petrologic diversity of Rábida is attributable to crystal-liquid segregation and reincorporation of plagioclase in various melts. These processes result in the eruption of pure melt, melt mixed with mush, and cumulates.

Constraining the Volatile Regime of Primitive Somma-Vesuvius Magmas Based on the Compositions of Phenocrysts and Melt Inclusions

NASA Astrophysics Data System (ADS)

Danyushevsky, L. V.; Esposito, R.; De Vivo, B.; Redi, D.; Lima, A.; Bodnar, R. J.; Gurenko, A.

2017-12-01

The volcanic complex of Mt. Somma-Vesuvius is located in the Campanian Plain on east of Naples. We present the results of a mineralogical and melt inclusion studies of primitive volcanic products erupted during the last 2 magmatic cycles of Soma-Vesuvius, aimed at better understanding the volatile fluxes and eruptive behaviour of the volcano. Our results suggest that despite large differences in the compositions of the erupted magmas (from olivine-bearing basaltic lavas to leucite-bearing phonolites) and the eruption style (from plinian to strombolian), there was very little change in the nature of the parental magmas. Melt inclusions in olivine phenocrysts in all volcanic products and styles reveal the highest volatile contents in the most magnesian, early formed crystals (Fo90; H2O 4-5 wt%; CO2 3,000-4,000 ppm), decreasing to near 0 levels of concentrations in olivine Fo70. Major and trace element compositions of the clinopyroxene phenocrysts (Mg#92-70) also suggest a similar parental magma composition and similar liquid lines of decent for all Somma-Vesuvius eruptions. Our results are best explained by a model which relates the eruption style to the intensity of melt supply under the volcano. High intensity plinian eruptions occur after a prolonged repose time, whereas strombolian eruptions occur during periods of more frequent volcanic activity [1]. We will also discuss possible implications for the role of carbonate assimilation during magma evolution of Somma-Vesuvius and for total volatile budget of the SOmma-Vesuvius eruptions. [1] [42] Lima, A., Danyushevsky, L.V., De Vivo, B. and Fedele, L. 2003: A model for the evolution of the Mt. Somma-Vesuvius magmatic system based on fluid and melt inclusion investigations. In: Melt Inclusions in volcanic systems: Methods, applications and Problems (B. De Vivo & R.J. Bodnar, Eds), Series: Developments in Volcanology. No. 5 Elsevier, Amsterdam, 227-251

Compositional diversity in peridotites as result of a multi-process history: The Pacific-derived Santa Elena ophiolite, northwest Costa Rica

NASA Astrophysics Data System (ADS)

Escuder-Viruete, Javier; Baumgartner, Peter O.; Castillo-Carrión, Mercedes

2015-08-01

The Santa Elena ophiolite (SEO) is an ultramafic nappe of more than 270 km2 overlying a tectonic serpentinite-matrix mélange in northwest Costa Rica. It is mainly composed of Cpx-rich and Cpx-poor harzburgites (~ 2.5 km-thick), with minor lherzolite, dunite and chromitite, as well as intrusive mafic sills and subvertical dikes, which coalesce into an upper Isla Negritos gabbroic sill complex. Minerals and whole-rock features of the Cpx-rich and Cpx-poor harzburgites share features of the abyssal and supra-subduction zone (SSZ) peridotites, respectively. To explain these characteristics two-stages of melting and refertilization processes are required. By means of trace element modeling, the composition of Cpx-rich harzburgites may be reproduced by up to ~ 5-10% melting of a primitive mantle source, and the composition of Cpx-poor harzburgites and dunites by ~ 15-18% melting of an already depleted mantle. Therefore, the Cpx-rich harzburgites can be interpreted as product of first-stage melting and low-degrees of melt-rock interaction in a mid-ocean ridge environment, and the Cpx-poor harzburgites and dunites as the product of second-stage melting and refertilization in a SSZ setting. The mafic sills and the Isla Negrito gabbros are genetically related and can be explained as crystallization from the liquids that were extracted from the lower SSZ mantle levels and emplaced at shallow conditions. The Murciélagos Island basalts are not directly related to the ultramafic and mafic rocks of the SEO. Their E-MORB-like composition is similar to most of the CLIP mafic lavas and suggests a common Caribbean plume-related source. The SEO represents a fragment of Pacific-derived, SSZ oceanic lithosphere emplaced onto the southern North America margin during the late Cretaceous. Because of the predominance of rollback-induced extension during its history, only a limited amount of crustal rocks were formed and preserved in the SEO.

Voluminous arc dacites as amphibole reaction-boundary liquids

NASA Astrophysics Data System (ADS)

Blatter, Dawnika L.; Sisson, Thomas W.; Hankins, W. Ben

2017-05-01

Dacites dominate the large-volume, explosive eruptions in magmatic arcs, and compositionally similar granodiorites and tonalites constitute the bulk of convergent margin batholiths. Shallow, pre-eruptive storage conditions are well known for many dacitic arc magmas through melt inclusions, Fe-Ti oxides, and experiments, but their potential origins deeper in the crust are not well determined. Accordingly, we report experimental results identifying the P-T-H2O conditions under which hydrous dacitic liquid may segregate from hornblende (hbl)-gabbroic sources either during crystallization-differentiation or partial melting. Two compositions were investigated: (1) MSH-Yn-1 dacite (SiO2: 65 wt%) from Mount St. Helens' voluminous Yn tephra and (2) MSH-Yn-1 + 10% cpx to force saturation with cpx and map a portion of the cpx + melt = hbl peritectic reaction boundary. H2O-undersaturated (3, 6, and 9 wt% H2O) piston cylinder experiments were conducted at pressures, temperatures, and fO2 appropriate for the middle to lower arc crust (400, 700, and 900 MPa, 825-1100 °C, and the Re-ReO2 buffer ≈ Ni-NiO + 2). Results for MSH-Yn-1 indicate near-liquidus equilibrium with a cpx-free hbl-gabbro residue (hbl, plg, magnetite, ± opx, and ilmeno-hematite) with 6-7 wt% dissolved H2O, 925 °C, and 700-900 MPa. Opx disappears down-temperature consistent with the reaction opx + melt = hbl. Cpx-added phase relations are similar in that once 10% cpx crystallizes, multiple saturation is attained with cpx, hbl, and plg, +/- opx, at 6-7 wt% dissolved H2O, 940 °C, and 700-900 MPa. Plg-hbl-cpx saturated liquids diverge from plg-hbl-opx saturated liquids, consistent with the MSH-Yn-1 dacite marking a liquid composition along a peritectic distributary reaction boundary where hbl appears down-temperature as opx + cpx are consumed. The abundance of saturating phases along this distributary peritectic (liquid + hbl + opx + cpx + plg + oxides) reduces the variance, so liquids are restricted to dacite-granodiorite-tonalite compositions. Higher-K dacites than the Yn would also saturate with biotite, further limiting their compositional diversity. Theoretical evaluation of the energetics of peritectic melting of pargasitic amphiboles indicates that melting and crystallization of amphibole occur abruptly, proximal to amphibole's high-temperature stability limit, which causes the system to dwell thermally under the conditions that produce dacitic compositions. This process may account for the compositional homogeneity of dacites, granodiorites, and tonalites in arc settings, but their relative mobility compared to rhyolitic/granitic liquids likely accounts for their greater abundance.

Composition of the Cayley Formation at Apollo 16 as inferred from impact melt splashes

NASA Technical Reports Server (NTRS)

Morris, Richard V.; Horz, Friedrich; See, Thomas H.

1986-01-01

Abundances of major and trace elements and magnetic properties of 50 impact melt splashes (IMSs) from the Apollo 16 landing site are analzyed to determine the composition of their meteoritic component. MgO-Sc and Ca-Sc variation diagrams and least-squares mixing models are utilized to analyze the IMS, soil, and rock data. Consideration is given to progenitor lithologies of the IMS, the number of impact events represented by the IMS, and the heterogeneity of impact melts from single events. It is observed that the IMSs are composed of either a mixture of anorthosite and low-Sc impact melt rocks or anorthositic norite. It is determined that the surface Cayley layer is composed of TiO2, MgO, Sc, and La concentrations of 0.69, and 7.1 wt pct and 10.5 and 21.2 microg/g, respectively and 0.38 and 5.9 wt pct and 6.1 and 11.8 microg/g, respectively, for the subsurface Cayley layer. The Descartes Formation composition is estimated as TiO2, MgO, Sc, and La concentrations of 0.25, and 3.5 wt pct and 7.7 and 2.2 microg/g, respectively.

Melt Inclusion Analysis of RBT 04262 with Relationship to Shergottites and Mars Surface Compositions

NASA Technical Reports Server (NTRS)

Potter, S. A.; Brandon, A. D.; Peslier, A. H.

2015-01-01

Martian meteorite RBT 04262 is in the shergottite class. It displays the two lithologies typically found in "lherzolitic shergottites": one with a poikilitic texture of large pyroxene enclosing olivine and another with non-poikilitic texture. In the case of RBT 04262, the latter strongly ressembles an olivine- phyric shergottite which led the initial classification of this meteorite in that class. RBT 04262 has been studied with regards to its petrology, geochemistry and cosmic ray exposure and belongs to the enriched oxidized end-member of the shergottites. Studies on RBT 04262 have primarily focused on the bulk rock composition or each of the lithologies independently. To further elucidate RBT 04262's petrology and use it to better understand Martian geologic history, an in-depth study of its melt inclusions (MI) is being conducted. The MI chosen for this study are found within olivine grains. MI are thought to be trapped melts of the crystallizing magma preserved by the encapsulating olivine and offer snapshots of the composition of the magma as it evolves. Some MI, in the most Mg-rich part of the olivine of olivine-pyric shergottites, may even be representative of the meteorite parent melt.

Green glass vitrophyre 78526 - An impact of very low-Ti mare basalt composition

NASA Technical Reports Server (NTRS)

Warner, R. D.; Taylor, G. J.; Kiel, K.; Planner, H. H.; Nehru, C. E.; Ma, M.-S.; Schmitt, R. A.

1978-01-01

Rake sample 78526 is an 8.77 g rock consisting primarily of vitrophyric pale green glass with subordinate mineral and lithic relics. Petrographic and compositional evidence leads to the following conclusions: (1) the bulk composition represents that of a mixture formed by impact melting of at least two different textural and compositional varieties of VLT mare basalt that are now present in the rock as lithic relics and a poorly defined low-Ti mare basalt component observed in thin section only in the form of isolated mineral relics; (2) the admixed VLT mare basalts had REE abundances lower than those found in other mare basalts (but probably higher than emerald green glass) and REE patterns showing significant enrichment of the heavy relative to light REE's, suggesting that they were derived by comparatively high degrees of partial melting of a clinopyroxene-rich source region; and (3) the impact melt supercooled to produce the vitrophyre, with rather sharply contrasting textural domains present in the vitrophyre resulting from differences in nucleation kinetics and degrees of supercooling in various portions of the sample.

Phase composition and microstructure of WC-Co alloys obtained by selective laser melting

NASA Astrophysics Data System (ADS)

Khmyrov, Roman S.; Shevchukov, Alexandr P.; Gusarov, Andrey V.; Tarasova, Tatyana V.

2018-03-01

Phase composition and microstructure of initial WC, BK8 (powder alloy 92 wt.% WC-8 wt.% Co), Co powders, ball-milled powders with four different compositions (1) 25 wt.% WC-75 wt.% Co, (2) 30 wt.% BK8-70 wt.% Co, (3) 50 wt.% WC-50 wt.% Co, (4) 94 wt.% WC-6 wt.% Co, and bulk alloys obtained by selective laser melting (SLM) from as-milled powders in as-melted state and after heat treatment were investigated by scanning electron microscopy and X-ray diffraction analysis. Initial and ball-milled powders consist of WC, hexagonal α-Co and face-centered cubic β-Co. The SLM leads to the formation of major new phases W3Co3C, W4Co2C and face-centered cubic β-Co-based solid solution. During the heat treatment, there occurs partial decomposition of the face-centered cubic β-Co-based solid solution with the formation of W2C and hexagonal α-Co solid solution. The microstructure of obtained bulk samples, in general, corresponds to the observed phase composition.

MeltMigrator: A MATLAB-based software for modeling three-dimensional melt migration and crustal thickness variations at mid-ocean ridges following a rules-based approach

NASA Astrophysics Data System (ADS)

Bai, Hailong; Montési, Laurent G. J.; Behn, Mark D.

2017-01-01

MeltMigrator is a MATLAB®-based melt migration software developed to process three-dimensional mantle temperature and velocity data from user-supplied numerical models of mid-ocean ridges, calculate melt production and melt migration trajectories in the mantle, estimate melt flux along plate boundaries, and predict crustal thickness distribution on the seafloor. MeltMigrator is also capable of calculating compositional evolution depending on the choice of petrologic melting model. Programmed in modules, MeltMigrator is highly customizable and can be expanded to a wide range of applications. We have applied it to complex mid-ocean ridge model settings, including transform faults, oblique segments, ridge migration, asymmetrical spreading, background mantle flow, and ridge-plume interaction. In this technical report, we include an example application to a segmented mid-ocean ridge. MeltMigrator is available as a supplement to this paper, and it is also available from GitHub and the University of Maryland Geodynamics Group website.

A sulfide-saturated lunar mantle?

NASA Astrophysics Data System (ADS)

Brenan, James M.; Mungall, James E.

2017-04-01

Although much work has been done to understand the controls on the sulfur content at sulfide saturation (SCSS) for terrestrial melt compositions, little information exists to evaluate the SCSS for the high FeO compositions typical of lunar magmas, and at the reduced conditions of the Moon's interior. Experiments were done to measure the SCSS for a model low Ti mare basalt with 20 wt% FeO at 1400oC as a function of fO2 and pressure. Synthetic lunar basalt was encapsulated along with stoichiometric FeS in capsules made from Fe-Ir alloy. The fO2 of the experiment can be estimated by the heterogeneous equilibrium: Femetal + 1 /2 O2 = FeOsilicate Variation in the metal composition, by addition of Ir, serves to change the fO2 of the experiment. Capsule compositions spanning the range Fe25Ir75 to Fe96Ir4 (at%) were synthesized by sintering of pressed powders under reducing conditions. Fe100 capsules were fabricated from pure Fe rod. For a melt with 20 wt% FeO, this range in capsule composition spans the fO2 interval of ˜IW-1 (Fe100, Fe96Ir4) to IW+2.2 (Fe25Ir75). Experiments were done over the pressure interval of 0.1 MPa to 2 GPa. Results for experiments involving Fe100capsules indicate that the SCSS decreases from ˜2000 ppm (0.1 MPa) to 700 ppm (2 GPa). Experiments done thus far at 1 GPa, involving the range of capsule compositions indicated, show a marked decrease in SCSS as the Fe content of the capsule increases (fO2 decreases). Complementary to the decrease in SCSS is a drop in the sulfur content of the coexisting sulfide melt, from ˜50 at% at ΔIW = +2.2 to ˜20 at% at ΔIW-1. In fact, both the composition of the sulfide melt and the SCSS are essentially indistinguishable for Fe96Ir4 and Fe100 compositions. Results thus far indicate that at reduced conditions and high pressure, the SCSS for high FeO lunar compositions is low, and overlaps with Apollo 11 melt inclusion data. Importantly, such low SCSS does not require Fe metal saturation, and suggests that some lunar source regions could be saturated in a low sulfur, sulfide melt. Additional sulfide-silicate partitioning experiments for the PGE and Re have also been done at Fe-metal saturation at 1400oC, 0.1 MPa using chromite capsules sealed in silica ampoules. Results confirm that the highly siderophile elements (HSE) will be strongly sequestered by residual sulfide, and that the concentrations of these elements will be strongly depleted in lunar basalts. Hence, estimates of the HSE content of the lunar mantle from basalt compositions must take into account the fractionation imposed by sulfide-silicate partitioning at reduced conditions.

Compositional zoning of the bishop tuff

USGS Publications Warehouse

Hildreth, W.; Wilson, C.J.N.

2007-01-01

Compositional data for >400 pumice clasts, organized according to eruptive sequence, crystal content, and texture, provide new perspectives on eruption and pre-eruptive evolution of the >4600 km3 of zoned rhyolitic magma ejected as the BishopTuff during formation of Long Valley caldera. Proportions and compositions of different pumice types are given for each ignimbrite package and for the intercalated plinian pumice-fall layers that erupted synchronously. Although withdrawal of the zoned magma was less systematic than previously realized, the overall sequence displays trends toward greater proportions of less evolved pumice, more crystals (0-5 24 wt %), and higher FeTi-oxide temperatures (714-818??C). No significant hiatus took place during the 6 day eruption of the BishopTuff, nearly all of which issued from an integrated, zoned, unitary reservoir. Shortly before eruption, however, the zoned melt-dominant portion of the chamber was invaded by batches of disparate lower-silica rhyolite magma, poorer in crystals than most of the resident magma but slightly hotter and richer in Ba, Sr, andTi. Interaction with resident magma at the deepest levels tapped promoted growth ofTi-rich rims on quartz, Ba-rich rims on sanidine, and entrapment of near-rim melt inclusions relatively enriched in Ba and CO2.Varied amounts of mingling, even in higher parts of the chamber, led to the dark gray and swirly crystal-poor pumices sparsely present in all ashflow packages. As shown by FeTi-oxide geothermometry, the zoned rhyolitic chamber was hottest where crystal-richest, rendering any model of solidification fronts at the walls or roof unlikely.The main compositional gradient (75-195 ppm Rb; 0.8-2.2 ppm Ta; 71-154 ppm Zr; 0.40-1.73% FeO*) existed in the melt, prior to crystallization of the phenocryst suite observed, which included zircon as much as 100 kyr older than the eruption.The compositions of crystals, though themselves largely unzoned, generally reflect magma temperature and the bulk compositional gradient, implying both that few crystals settled or were transported far and that the observed crystals contributed little to establishing that gradient. Upward increases in aqueous gas and dissolved water, combined with the adiabatic gradient (for the 5 km depth range tapped) and the roofward decline in liquidus temperature of the zoned melt, prevented significant crystallization against the roof, consistent with dominance of crystal-poor magma early in the eruption and lack of any roof-rind fragments among the Bishop ejecta, before or after onset of caldera collapse. A model of secular incremental zoning is advanced wherein numerous batches of crystal-poor melt were released from a mush zone (many kilometers thick) that floored the accumulating rhyolitic melt-rich body. Each batch rose to its own appropriate level in the melt-buoyancy gradient, which was selfsustaining against wholesale convective re-homogenization, while the thick mush zone below buffered it against disruption by the deeper (non-rhyolitic) recharge that augmented the mush zone and thermally sustained the whole magma chamber. Crystal-melt fractionation was the dominant zoning process, but it took place not principally in the shallow melt-rich body but mostly in the pluton-scale mush zone before and during batchwise melt extraction. ?? Published by Oxford University Press (2007).

Viscosities of Fe Ni, Fe Co and Ni Co binary melts

NASA Astrophysics Data System (ADS)

Sato, Yuzuru; Sugisawa, Koji; Aoki, Daisuke; Yamamura, Tsutomu

2005-02-01

Viscosities of three binary molten alloys consisting of the iron group elements, Fe, Ni and Co, have been measured by using an oscillating cup viscometer over the entire composition range from liquidus temperatures up to 1600 °C with high precision and excellent reproducibility. The viscosities measured showed good Arrhenius linearity for all the compositions. The viscosities of Fe, Ni and Co as a function of temperature are as follows: \\eqalign{ & \\log \\eta={-}0.6074 + 2493/T\\qquad for\\quad Fe\\\\ & \\log \\eta={-}0.5695 + 2157/T\\qquad for\\quad Ni \\\\ & \\log \\eta={-}0.6620 + 2430/T\\qquad for\\quad Co.} The isothermal viscosities of Fe-Ni and Fe-Co binary melts increase monotonically with increasing Fe content. On the other hand, in Ni-Co binary melt, the isothermal viscosity decreases slightly and then increases with increasing Co. The activation energy of Fe-Co binary melt increased slightly on mixing, and those of Fe-Ni and Ni-Co melts decreased monotonically with increasing Ni content. The above behaviour is discussed based on the thermodynamic properties of the alloys.

Cycling of sulfur in subduction zones: The geochemistry of sulfur in the Mariana Island Arc and back-arc trough

USGS Publications Warehouse

Alt, J.C.; Shanks, Wayne C.; Jackson, M.C.

1993-01-01

The sulfur contents and sulfur isotopic compositions of 24 glassy submarine volcanics from the Mariana Island Arc and back-arc Mariana Trough were determined in order to investigate the hypothesis that subducted seawater sulfur (??34S = 21???) is recycled through arc volcanism. Our results for sulfur are similar to those for subaerial arc volcanics: Mariana Arc glasses are enriched in 34S (??34S = up to 10.3???, mean = 3.8???) and depleted in S (20-290 ppm, mean = 100 ppm) relative to MORB (850 ppm S, ??34S = 0.1 ?? 0.5???). The back-arc trough basalts contain 200-930 ppm S and have ??34S values of 1.1 ?? 0.5???, which overlap those for the arc and MORB. The low sulfur contents of the arc and some of the trough glasses are attributed to (1) early loss of small amounts of sulfur through separation of immiscible sulfide and (2) later vapor-melt equilibrium control of sulfur contents and loss of sulfur in a vapor phase from sulfide-undersaturated melts near the minimum in sulfur solubility at f{hook}O2 ??? NNO (nickel-nickel oxide). Although these processes removed sulfur from the melts their effects on the sulfur isotopic compositions of the melts were minimal. Positive trends of ??34S with 87Sr 86Sr, LILE and LREE contents of the arc volcanics are consistent with a metasomatic seawater sulfur component in the depleted sub-arc mantle source. The lack of a 34S-rich slab signature in the trough lavas may be attributed to equilibration of metasomatic fluid with mantle material along the longer pathway from the slab to the source of the trough volcanics. Sulfur is likely to have been transported into the mantle wedge by metasomatic fluid derived from subducted sediments and pore fluids. Gases extracted from vesicles in arc and back-arc samples are predominantly H2O, with minor CO2 and traces of H2S and SO2. CO2 in the arc and back-arc rocks has ??13C values of -2.1 to -13.1???, similar to MORB. These data suggest that degassing of CO2 could explain the slightly lower ??13C values for some Mariana Trough volcanic glasses, and that incorporation of subduction-derived organic carbon into the Mariana Trough mantle source may not be necessary. More analyses are required to resolve this question, however. ?? 1993.

Generating Melt During Exhumation of Continental Crust from Ultrahigh Pressure (UHP) Conditions

NASA Astrophysics Data System (ADS)

Brown, M.; Wang, S.; Wang, L.; Piccoli, P. M.; Johnson, T. E.

2017-12-01

Hydrate breakdown rather than fluid-present melting is commonly cited during exhumation of UHP continental crust, but may have been overemphasized in relation to petrographic evidence. In this study from the central Sulu belt, China, we posit that dm- to m-scale dikes of leucosome in stromatic migmatite, formerly UHP eclogite, crystallized from hydrous melt derived by evolution of supercritical fluid as it drained through exhuming crust and increased in solute content. Leucosomes comprise Qz + Ph + Ab + Aln/Ep + Grt. Overgrowths of Zrn on inherited cores and new grains crystallized at ca. 223-219 Ma, within the age range of HP eclogite facies recrystallization in the belt. Si-in-Ph/Ti-in-Zrn thermobarometry yields crystallization conditions of 3.0-2.5 GPa at 830-770 °C. Compositions are granitic with normalized TE patterns enriched in LREE relative to HREE and enriched in LILE relative to HFSE, features consistent with crystallization from crustally derived hydrous melt. The leucosomes have Sr-Nd isotope compositions intermediate between host eclogites and surrounding gneisses. At the metamorphic peak, the source rocks were likely fluid deficient or fluid absent. During exhumation from UHP conditions, structural water stored in nominally anhydrous minerals during the prograde evolution was exsolved to form a grain boundary supercritical fluid in eclogite and gneiss. By migrating from grain boundaries into channels and draining from the volumetrically dominant gneiss through eclogite, the fluid acquired a blended Sr-Nd isotope composition intermediate between end-members. Concomitantly, the ascending fluid evolved to a denser, more viscous and more polymerized hydrous melt by dissolution of the silicate matrix. Trapped around the transition from UHP to HP eclogite facies conditions, the melt crystallized by diffusive loss of water to the host eclogite. Aggregates of Pl + Bt around Ph and thin films and cuspate veinlets/patches of Kfs along grain boundaries in leucosomes are consistent with subsequent low degrees of melting by Ph breakdown. Phase equilibria modeling indicates melting occurred during the transition from HP eclogite to amphibolite facies, with final subsolidus equilibration at 1.04-0.87 GPa and T <640 °C. However, Ph-breakdown melting was not the mechanism by which the leucosomes formed.

Melting mode and source lithology inferred from trace element systematic in historical olivine from Lanzarote, Canary Islands

NASA Astrophysics Data System (ADS)

Gómez-Ulla, Alejandra; Sigmarsson, Olgeir; Guðfinnsson, Guðmundur H.

2017-04-01

Trace element concentrations and ratios in olivine phenocrysts, such as fractionation-corrected Ni x (FeO/MgO) and Fe/Mn, have been shown useful as probes of pyroxenite derived component in mixtures of primary mantle melts (e.g. Sobolev et al., 2007). For instance, higher Ni and lower Mn and Ca contents are expected in partial melts of pyroxenite compared to those of lherzolite. We have measured trace element concentrations in olivine from 1730-1736 AD (Timanfaya) and 1824 AD eruptions in Lanzarote (Canary Islands), which erupted mafic and mantle nodule bearing magmas, ranging in composition from highly silica-undersaturated basanite through alkali basalt to tholeiite. The early basanite exhibit the largest olivine trace element variation covering the range of those from MORB and OIB worldwide, whereas later erupted tholeiite have values typical from pyroxenite derived melts. The Fo value decreased systematically with time during the 1730-36 eruption and the proportion of silica-saturated primary melt increased in the parental magma mixture with time. At the end of the eruption, tholeiite magmas crystallized olivine with, increasing concentrations of Mn and Ca and higher Ca/Al at relatively uniform Ni x (FeO/MgO) and Fe/Mn, all of which is readily explained by increased decompression melting at lower temperature. The basanite from the eruption that took place in 1824 AD has olivine with even higher Fo value and trace element variability similar those of the Timanfaya basanite. The fact that the Lanzarote basanite contain olivine with trace element systematic spanning that of MORB and pyroxenite melt can be explained by CO2-flux melting of a lithologically heterogeneous source, generating the diverse compositions. Initial reactive porous flow through depleted oceanic lithosphere and equilibration with dunitic restite of percolating pyroxenite melt may have amplified the observed Ni depletion in olivine of the earliest basanite. The fact that olivine compositions and basanite magma were reproduced approximately a century later may reflect episodic carbonatic fluxing in the slowly uprising Canarian mantle plume.

Slab and Sediment Melting during Subduction Initiation: Mantle Plagiogranites from the Oman Ophiolite

NASA Astrophysics Data System (ADS)

Rollinson, H. R.

2014-12-01

Granitoid dykes up to several hundred metres wide and 2 km long are found in depleted harzburgites in the mantle section of the Oman ophiolite. They vary in composition from tonalite to potassic granite and are generally more potassic than the crustal plagiogranites found within the sheeted dyke complex higher up within the ophiolite stratigraphy. Some granites are strongly peraluminous and contain garnet and andalusite. They are geochemically variable, some with REE that are relatively unfractionated ((La/Yb)n= 3.5-6.0, flat middle to heavy REE, steep light REE) to those which are highly fractionated ((La/Yb)n= 28-220). On primitive-mantle normalised plots some have very high concentrations of fluid-mobile elements - Cs, Rb, Th, U and Pb. Few have significant Ta-Nb anomalies. On the Ca-Fe-Mg-Ti discrimination diagram of Patino Douce (J. Petrol., 1999) whole-rock compositions define a spectrum between felsic-pelite derived melts and amphibolite-derived melts. There is a chemical similarity between the least REE fractionated plagiogranites (generally tonalites and granodiorites) and melts of an amphibolitic parent. This is supported by the occurrence of mafic xenoliths in some dykes, the presence of hornblende and highly calcic cores (up to An85) in some plagioclase grains. Trace element modelling using Oman Geotimes lavas as the starting composition indicates that melting took place in the garnet stability field, although enrichment in the melt in Cs, Rb, Ba and Pb suggests that there was another component present in addition to the mafic parent. Other plagiogranites (trondhjemites and granites) have a strongly peraluminous chemistry and mineralogy and geochemical similarities with the Himalayan leucogranites implying that they were derived from a sedimentary protolith. These mantle plagiogranites are more prevalent in the northern outcrops of the ophiolite. The volume of granitoid melt and the depth of melting preclude their derivation from the sole of the ophiolite, rather they were derived during subduction by the partial melting of the slab and associated sediment and emplaced into the overlying mantle wedge. Current subduction-initiation models for supra-subduction ophiolites should integrate this process into their thinking.

Osmium isotope and highly siderophile element systematics of lunar impact melt breccias: Implications for the late accretion history of the Moon and Earth

USGS Publications Warehouse

Puchtel, I.S.; Walker, R.J.; James, O.B.; Kring, D.A.

2008-01-01

To characterize the compositions of materials accreted to the Earth-Moon system between about 4.5 and 3.8 Ga, we have determined Os isotopic compositions and some highly siderophile element (HSE: Re, Os, Ir, Ru, Pt, and Pd) abundances in 48 subsamples of six lunar breccias. These are: Apollo 17 poikilitic melt breccias 72395 and 76215; Apollo 17 aphanitic melt breccias 73215 and 73255; Apollo 14 polymict breccia 14321; and lunar meteorite NWA482, a crystallized impact melt. Plots of Ir versus other HSE define excellent linear correlations, indicating that all data sets likely represent dominantly two-component mixtures of a low-HSE target, presumably endogenous component, and a high-HSE, presumably exogenous component. Linear regressions of these trends yield intercepts that are statistically indistinguishable from zero for all HSE, except for Ru and Pd in two samples. The slopes of the linear regressions are insensitive to target rock contributions of Ru and Pd of the magnitude observed; thus, the trendline slopes approximate the elemental ratios present in the impactor components contributed to these rocks. The 187Os/188Os and regression-derived elemental ratios for the Apollo 17 aphanitic melt breccias and the lunar meteorite indicate that the impactor components in these samples have close affinities to chondritic meteorites. The HSE in the Apollo 17 aphanitic melt breccias, however, might partially or entirely reflect the HSE characteristics of HSE-rich granulitic breccia clasts that were incorporated in the impact melt at the time of its creation. In this case, the HSE characteristics of these rocks may reflect those of an impactor that predated the impact event that led to the creation of the melt breccias. The impactor components in the Apollo 17 poikilitic melt breccias and in the Apollo 14 breccia have higher 187Os/188Os, Pt/Ir, and Ru/Ir and lower Os/Ir than most chondrites. These compositions suggest that the impactors they represent were chemically distinct from known chondrite types, and possibly represent a type of primitive material not currently delivered to Earth as meteorites. ?? 2008 Elsevier Ltd.

Deformation, static recrystallization, and reactive melt transport in shallow subcontinental mantle xenoliths (Tok Cenozoic volcanic field, SE Siberia)

NASA Astrophysics Data System (ADS)

Tommasi, Andréa; Vauchez, Alain; Ionov, Dmitri A.

2008-07-01

Partial melting and reactive melt transport may change the composition, microstructures, and physical properties of mantle rocks. Here we explore the relations between deformation and reactive melt transport through detailed microstructural analysis and crystallographic orientation measurements in spinel peridotite xenoliths that sample the shallow lithospheric mantle beneath the southeastern rim of the Siberian craton. These xenoliths have coarse-grained, annealed microstructures and show petrographic and chemical evidence for variable degrees of reaction with silicate melts and fluids, notably Fe-enrichment and crystallization of metasomatic clinopyroxene (cpx). Olivine crystal preferred orientations (CPO) range from strong to weak. [010]-fiber patterns, characterized by a point concentration of [010] normal to the foliation and by dispersion of [100] in the foliation plane with a weak maximum parallel to the lineation, predominate relative to the [100]-fiber patterns usually observed in lithospheric mantle xenoliths and peridotite massifs. Variations in olivine CPO patterns or intensity are not correlated with modal and chemical compositions. This, together with the analysis of microstructures, suggests that reactive melt percolation postdated both deformation and static recrystallization. Preferential crystallization of metasomatic cpx along (010) olivine grain boundaries points to an influence of the preexisting deformation fabrics on melt transport, with higher permeability along the foliation. Similarity between orthopyroxene (opx) and cpx CPO suggests that cpx orientations may be inherited from those of opx during melt-rock reaction. As observed in previous studies, reactive melt transport does not weaken olivine CPO and seismic anisotropy in the upper mantle, except in melt accumulation domains. In contrast, recovery and selective grain growth during static recrystallization may lead to development of [010]-fiber olivine CPO and, if foliations are horizontal, result in apparent isotropy for vertically propagating SKS waves, but strong anisotropy for horizontally propagating surface waves.

Carbonate-silicate liquid immiscibility in the mantle propels kimberlite magma ascent

NASA Astrophysics Data System (ADS)

Kamenetsky, Vadim S.; Yaxley, Gregory M.

2015-06-01

Kimberlite is a rare volcanic rock renowned as the major host of diamonds and originated at the base of the subcontinental lithospheric mantle. Although kimberlite magmas are dense in crystals and deeply-derived rock fragments, they ascend to the surface extremely rapidly, enabling diamonds to survive. The unique physical properties of kimberlite magmas depend on the specific compositions of their parental melts that, in absence of historical eruptions and due to pervasive alteration of kimberlite rocks, remain highly debatable. We explain exceptionally rapid ascent of kimberlite magma from mantle depths by combining empirical data on the essentially carbonatite composition of the kimberlite primary melts and experimental evidence on interaction of the carbonate liquids with mantle minerals. Our experimental study shows that orthopyroxene is completely dissolved in a Na2CO3 melt at 2.0-5.0 GPa and 1000-1200 °C. The dissolution of orthopyroxene results in homogeneous silicate-carbonate melt at 5.0 GPa and 1200 °C, and is followed by unmixing of carbonate and carbonated silicate melts and formation of stable magmatic emulsion at lower pressures and temperatures. The dispersed silicate melt has a significant capacity for storing a carbonate component in the deep mantle (13 wt% CO2 at 2.0 GPa). We envisage that this component reaches saturation and is gradually released as CO2 bubbles, as the silicate melt globules are transported upwards through the lithosphere by the carbonatite magma. The globules of unmixed, CO2-rich silicate melt are continuously produced upon further reaction between the natrocarbonatite melt and mantle peridotite. On decompression the dispersed silicate melt phase ensures a continuous supply of CO2 bubbles that decrease density and increase buoyancy and promote rapid ascent of the magmatic emulsion.

Basalts, gabbroic cumulates and andesite generation in the Lesser Antilles - An experimental perspective

NASA Astrophysics Data System (ADS)

Pichavant, M.; Di Carlo, I.; Lesne, P.; Wulput, L.; Maury, R. C.; Macdonald, R.

2012-12-01

New experiments have been performed to explore the petrological relationships between basaltic magmas, gabbroic cumulates, amphibole (Amph) crystallization and andesite generation in the Lesser Antilles arc. Four natural basalt starting materials representative of typical high-MgO (HMB) and high-Al2O3 (HAB) along the arc have been selected. Results are combined with previous experimental work on mafic melts from Mt Pelée and St Vincent. Under H2O-saturated conditions, Amph stability is about 25°C higher in HMB than HAB, being limited to a maximum of1050-1100°C at 10 kbar. Amph is the liquidus phase for the 3 high-Al2O3 basalts above 4 kbar (> 6 wt% H2O in melt), and very close to the liquidus for the high-MgO basalt at 10 kbar (9-10 wt% H2O in melt). Derivative liquids from the crystallization of Amph-bearing assemblages are basaltic to dacitic, depending on parental melt composition, extent of crystallization and experimental fO2. Fractionation of > 20 wt% Amph is necessary to produce andesitic-dacitic liquids from basaltic parents. Amph composition reflects the Al/Si and Mg# of their parental melts. It generally divides into two groups, one Si-poor and Al-rich (pargasite: gabbroic cumulates, basalts, andesites) and the other Si-rich and Al-poor (edenite: dioritic cumulates, andesites, dacites). The systematic presence of Amph in gabbroic cumulate blocks, its near-absence in basaltic to andesitic lavas, plus the compositional contrast between the two Amph groups, suggest the existence of an Amph-free "window" along the P-T-X magma evolution trend. In gabbroic cumulates, Amph shows systematic differences between islands (similar Mg# but higher AlIV in Martinique than in St Vincent). Our experimental results suggest that the origin of the St Vincent gabbroic assemblages can be traced back to residual melts generated from the crystallization of high-MgO basalts. However, Amph with the highest AlIV(eg, Martinique, Montserrat) have not been reproduced in our experiments, suggesting that these gabbroic assemblages originate from melts different from our starting compositions. High AlIV in Amph (at high Mg#) implies highly aluminous and/or silica-poor primitive parental melts unlike the high-MgO basalt group. We explore the different possibilities for the origin of such parental melts, including the hypothesis of the existence of at least two types of primitive liquids in the Lesser Antilles arc.

Geochemistry and thermodynamics of an earthquake: A case study of pseudotachylites within mylonitic granitoid

NASA Astrophysics Data System (ADS)

Jiang, Hehe; Lee, Cin-Ty A.; Morgan, Julia K.; Ross, Catherine H.

2015-11-01

Pseudotachylites are melts produced by frictional heating during seismic slip. Understanding their origin and their influence on slip behavior is critical to understanding the physics of earthquakes. To provide insight into this topic, we conducted a case study in the proto-mylonitic to mylonitic Asbestos Mountain granitoid in the eastern Peninsular Ranges batholith (California), which records both ductile (mylonites) and brittle deformation features (pseudotachylites and ultracataclasites). U-Pb chronology and Zr thermometry of titanite porphyroblasts in the mylonites indicate that mylonitization of the plutons occurred at near solidus conditions (∼ 750 °C) over a 10 Ma interval from 89 to 78 Ma. Mylonitization resulted in recrystallization of quartz, plagioclase and biotite, with the biotite concentrated into biotite-rich foliation planes. Subsequent brittle deformation is superimposed on the ductile fabrics. Micro-XRF elemental mapping and in situ LA-ICP-MS analyses on these brittle deformation products show that the pseudotachylites are more mafic (lower Si, but higher Fe) and K-rich than the host mylonite, while the ultracataclasites are intermediate between the host and the pseudotachylites. Inverse mass balance calculations show that both brittle deformation products are depleted in quartz but enriched in biotite, with the pseudotachylites showing the most significant enrichment in biotite, indicating preferential involvement of biotite during brittle deformation. We suggest that biotite-rich layers generated during ductile deformation may have been the preferred locus of subsequent brittle deformation, presumably because such layers represent zones of weakness. Frictional heating associated with slip along such planes results in melting, which causes a decrease in viscosity, in turn leading to further strain localization. During the short time span of an earthquake, frictional melting appears to be a disequilibrium process, in which the minerals are melted in order of their melting points, from biotite (∼ 800 °C) to plagioclase (∼ 1400 °C) and finally to quartz (∼ 1700 °C), rather than by equilibrium melting, which results in silicic eutectoid melts at lower temperatures (∼ 650 °C). Thus, with progressive slip, melt composition should evolve from mafic to felsic, eventually approaching the bulk composition of the host rock. The mafic composition of the pseudotachylites thus indicates that they formed between the melting point of biotite and plagioclase (800- 1400 °C). Our chemical and modeling analyses on the pseudotachylites suggest that the chemical composition of pseudotachylites can potentially be used to constrain the thermodynamic conditions in the shear zone as well as earthquake source mechanics.

Minerals and melt inclusions as keys to understanding magma reservoir processes during formation of volcanic and plutonic mafic-ultramafic complexes in the Maimecha Kotui Province (Polar Siberia)

NASA Astrophysics Data System (ADS)

Simonov, Vladimir; Vasiliev, Yurii; Kotlyarov, Alexey; Stupakov, Sergey

2016-04-01

Magmatic complexes in the Maimecha Kotui Province (Polar Siberia) attract attention of researchers because they contain ultramafic volcanic rocks - meimechites, being products of crystallization of the ultrabasic deep mantle melts (Sobolev et al., 1991, 2009, 2011; Ryabchikov et al., 2002; Vasiliev, Gora, 2014). Effusive meimechites together with intrusive dunites of the Guli massif form ancient (253-246 Ma) volcanic and plutonic association, in which also pyroxenites and alkaline rocks are situated. Conditions of formation of this association were established with the help of minerals and melt inclusions study. The cumulative structure of the Guli massif dunites consists of rather large (2-4 mm) olivine crystals and dividing them zones (0.5-0.7 mm), filled with fine grains of clinopyroxenes and ore minerals (magnetite, ilmenite and chromite). The extended forms of well faceted pyroxene crystals testify to their fast growth from melt between cumulative olivines. Thus, crystallization of clinopyroxenes and ore minerals leads to formation between olivines ore pyroxenites, which are presented in the Guli massif by independent bodies. Analysis of olivine, Cr-spinel and clinopyroxene compositions testify to similarity of conditions of the Guli massif dunites crystallization on the one hand with formation of platinum-bearing Uralian-Alaskan-type mafic-ultramafic complexes and with another - show participation of meimechite magma. Major element composition of melt inclusions in Cr-spinel has shown that dunites of the Guli massif were crystallized with participation of subalkaline picrite magmatic systems, that are relative to melts, responsible of formation of platinum-bearing mafic-ultramafic complexes and meimechites. Peculiarities of trace and rare-earth elements distribution in melt inclusions in Cr-spinel of dunites are actually similar to inclusions in olivine of meimechites. Overall, data on composition of inclusions directly testify to formation of considered dunites from ultrabasic melt close to meimechite magma. The affinity of melts, forming dunites and meimechites, is confirmed by computer simulations, shown high crystallization temperature of olivines from dunites (1590-1415°C) (Simonov et al., 2014, 2015), actually coinciding with data on olivines from meimechite - 1600-1420°C (Sobolev et al., 1991, 2009). A part of this ultrabasic melts was crystallized in the magma chambers (with formation of cumulative dunites) and another part - came up to a surface with formation of effusive meimechites. Presence in Cr-spinels from Guli massif dunites melt inclusions with rather large (up to 50 μm) well faceted olivine crystals, situated in the quenching fine-grained association of minerals (clinopyroxene, feldspar and nepheline), testifies to change of a quiet mode of crystallization by sharp falling of parameters of magma during olivine cumulation in the magma chamber, that resulted in appearance of alkaline rocks. As a whole, minerals and melt inclusions study testify to formation of volcanic and plutonic complexes in the Maimecha Kotui Province (Polar Siberia) as a result of evolution of primary deep mantle ultrabasic melts (similar by its chemical composition to meimechites) during cumulative processes in the magma chambers.

Amphibole and Phlogopite Formation on the R Chondrite Parent Body: An Experimental Investigation

NASA Astrophysics Data System (ADS)

Lunning, N. G.; Waters, L. E.; McCoy, T. J.

2017-07-01

High-temperature hydrated minerals can form at the pressures and the temperatures expected for the interiors of planetesimals. Under water-saturated conditions, minimum silicate melting can initiate at temperatures as low as 870°C at 40 MPa.

Interactions between surface waters in King George Island, Antarctica - a stable isotope perspective

NASA Astrophysics Data System (ADS)

Perşoiu, Aurel; Bădăluşă, Carmen

2017-04-01

In this paper we present a first study of the isotopic composition of surface waters in the southern peninsulas (Barton, Fildes, Weaver and Potter) of King George Island, Antarctica. We have collected > 200 samples of snow and snowmelt, water (lake, river and spring), ice (glacier ice and permafrost) from the four peninsulas in February 2016 and analyzed them for their oxygen and hydrogen stable isotopic composition. Samples from lake water (50+) indicate a clear west-east depletion trend, suggesting a rain-out process as air masses are moving westward (and are progressively depleted in heavy isotopes) from their origin in the Drake Passage. In both Fildes and Barton Peninsulas, permafrost samples have the heaviest isotopic composition, most probably due to preferential incorporation of heavy isotopes in the ice during freezing (and no fractionation during melting). As permafrost melts, the resulting water mixes with isotopically lighter infiltrated snowmelt, and thus the groundwater has a lower isotopic composition. Further, lake and river (the later fed by lakes) water has the lightest isotopic composition, being derived mostly from the melting of light snow and glacier ice. It seems feasible to separate isotopically water in lakes/rivers (largely fed by melting multi-year glaciers and snow) and water from melting of snow/ground ice This preliminary study suggests that it is possible to separate various water sources in the southern peninsulas of King George Island, and this separation could be used to study permafrost degradation, as well as feeding and migration patterns in the bird fauna, with implications for protection purposes. Acknowledgments. The National Institute of Research and Development for Biological Sciences (Bucharest, Romania) and the Korean polar institute financially supported fieldwork in King George Island. We thank the personal at King Sejong (South Korea), Belingshaussen (Russia) and Carlini (Argentina) stations in King George Island for logistic supports.

Trace element evidence for a depleted component intrinsic to the Hawaiian plume

NASA Astrophysics Data System (ADS)

DeFelice, C.; Mallick, S.; Saal, A. E.; Huang, S.

2017-12-01

The Hawaii Scientific Drilling Project (HSDP) recovered 3.5 km of Mauna Kea post-shield and shield stage basalts to investigate the geochemical evolution of a Hawaiian shield stage volcano and to constrain the geochemical structure of Hawaiian plume. A group of tholeiitic lavas from 1760-1810 meters below sea level (mbsl) have higher CaO content at given MgO content and are called high-CaO basalts. Isotopes of Pb, Sr, Hf, and Nd of these basalts show they are the most depleted shield basalts ever recovered in Hawaii. Their 206Pb/204Pb-208Pb/204Pb values indicate that they are not related to Pacific MORB. Their Ba/Th values (115-160) are characteristic of Hawaiian plume material and they are isotopically similar to Hawaiian rejuvenated stage lavas. To further investigate this relationship, we compare high-CaO basalts to the Honolulu Volcanics, a set of rejuvenated stage lavas. To determine their possible petrogenetic relation, we calculate their parental melt composition by adding or removing olivine until their geochemical composition is in equilibrium with Fo90. The High-CaO basalt parent magma composition has a much flatter REE pattern and much lower absolute REE contents than that of the Honolulu lavas. Batch melting forward models are calculated to determine potential sources that could contribute to both the Honolulu Volcanics and high-CaO basalts petrogenesis. Both parental magma compositions can be recreated by melting the same rejuvenated-stage source composition to varying degrees. Honolulu Volcanics are the result of a low degree of melting of the rejuvenated source, while higher degrees of melting reproduce the high-CaO basalts. The High-CaO basalts, erupted during shield-stage volcanism, show that the depleted component that rejuvenated stage basalts form from can be sampled during the most voluminous stage of volcanism, and is likely intrinsic to the plume.

First results from analysis of coordinated AVIRIS, TIMS, and ISM (French) data for the Ronda (Spain) and Beni Bousera (Morocco) peridotites

NASA Technical Reports Server (NTRS)

Mustard, J. F.; Hurtrez, S.; Pinet, P.; Sotin, C.

1992-01-01

Ultramafic rocks are relatively rare at the Earth's surface but constitute the vast majority of the Earth by volume. Exposures of ultramafic bodies are therefore crucial for deducing many important processes that occur in the Earth's mantle. An important science question regarding the spatial distribution, abundance, and composition of mafic minerals in ultramafic bodies that can be examined with advanced sensor data is the melting process. When a lherzolite melts, clinopyroxene (cpx) melts first and therefore variations in the modal amount of cpx remaining in the mantle are a reflection of the amount of fractional melting that has occurred. Fe goes preferentially into the melt during melting but a 20 percent batch melting (i.e. closed system) acquires less Fe relative to 20 percent fractional melting (i.e. open system). Since the strength and wavelength of diagnostic absorptions is a strong function of Fe content, it is possible to make maps of the variation in Fe:Mg ratios which can be related to the general melting process. Accurate ground-truth information about local mineralogy provides internal calibration and consistency checks. Investigations using imaging spectrometer are very complementary to field studies because advanced sensor data can provide a synoptic view of modal mineralogy and chemical composition whereas field studies focus on detailed characterization of local areas. Two excellent exposures of ultramafic lithologies are being investigated with visible to mid-infrared imaging spectrometer data: the Ronda peridotite near Ronda, Spain and the Beni Bousera ophiolitic fragment in northern Morocco. Although separated by the Alboran Sea, these bodies are thought to be related and represent fertile sub-continental mantle. The Ronda peridotite is predominantly spinel lherzolite but grades into harzburgite and shows considerable variation in major and trace element compositions. Mafic layering and dykes (i.e. olivine gabbro) are also observed. This indicates some sections of the peridotite have experienced greater degrees of partial melting. The Beni Bousera peridotite also contains mafic layers and dykes and grades into harzburgite representing similar fundamental shifts in the bulk chemistry of this ultramafic body probably related to an episode of partial melting. The specific mode of emplacement of these bodies is controversial and important for understanding the tectonic evolution of this region. Our investigations are not necessarily designed to help resolve this controversy. Rather, these exposures provide excellent and unusual examples of fertile mantle which have undergone variable degrees of partial melting.

Dynamics of the Axial Melt Lens/Dike transition at fast spreading ridges: assimilation and hydrous partial melting

NASA Astrophysics Data System (ADS)

France, L.; Ildefonse, B.; Koepke, J.

2009-04-01

Recent detailed field studies performed in the Oman ophiolite on the gabbro/sheeted dike transition, compared to corresponding rocks from the EPR drilled by IODP (Site 1256), constrain a general model for the dynamics of the axial melt lens (AML) present at fast spreading ridges (France et al., 2008). This model implies that the AML/dike transition is a dynamic interface migrating up- and downward, and that the isotropic gabbro horizon on top of the igneous section represents its fossilization. It is also proposed that upward migrations are associated to reheating of the base of the sheeted dike complex and to assimilation processes. Plagiogranitic lithologies are observed close to the truncated base of the dikes and are interpreted to represent frozen melts generated by partial melting of previously hydrothermalized sheeted dikes. Relicts of previously hydrothermalized lithologies are also observed in the fossil melt lens, and are associated to lithologies that have crystallized under high water activities, with clinopyroxene crystallizing before plagioclase, and An-rich plagioclase. To better understand our field data, we performed hydrous partial melting experiments at shallow pressures (0.1 GPa) under slightly oxidizing conditions (NNO oxygen buffer) and water saturated conditions on hydrothermalized sheeted dike sample from the Oman ophiolite. These experiments have been performed between 850°C and 1030°C; two additional experiments in the subsolidus regime were also conducted (750°C and 800°C). Clinopyroxenes formed during incongruent melting at low temperature (<910°C) have compositions that match those from the corresponding natural rocks (reheated base of the sheeted dike and relicts of assimilated lithologies). In particular, the characteristic low TiO2 and Al2O3 contents are reproduced. The experimental melts produced at low temperatures correspond to compositions of typical natural plagiogranites. In natural settings, these silicic liquids would be mixed with the basaltic melt of the AML, resulting in intermediate compositions that can be observed in the isotropic gabbro horizon. Our study suggests that assimilation of previously hydrothermalized lithologies in the melt lens is a common process at fast spreading ridges. This process should consequently be carefully considered in geochemical studies that deal with the origin of MORB. France L., Ildefonse B., Koepke J., (2008) The fossilisation of a dynamic melt lens at fast spreading centers: insights from the Oman ophiolite. Eos Trans. AGU, 89(53), Fall Meet. Suppl. Abstract V51F-2111

Mesoarchean melting and Neoarchean to Paleoproterozoic metasomatism during the formation of the cratonic mantle keel beneath West Greenland

NASA Astrophysics Data System (ADS)

van Acken, D.; Luguet, A.; Pearson, D. G.; Nowell, G. M.; Fonseca, R. O. C.; Nagel, T. J.; Schulz, T.

2017-04-01

Highly siderophile element (HSE) concentration and 187Os/188Os isotopic heterogeneity has been observed on various scales in the Earth's mantle. Interaction of residual mantle peridotite with infiltrating melts has been suggested to overprint primary bulk rock HSE signatures originating from partial melting, contributing to the heterogeneity seen in the global peridotite database. Here we present a detailed study of harzburgitic xenolith 474527 from the Kangerlussuaq suite, West Greenland, coupling the Re-Os isotope geochemistry with petrography of both base metal sulfides (BMS) and silicates to assess the impact of overprint induced by melt-rock reaction on the Re-Os isotope system. Garnet harzburgite sample 474527 shows considerable heterogeneity in the composition of its major phases, most notably olivine and Cr-rich garnet, suggesting formation through multiple stages of partial melting and subsequent metasomatic events. The major BMS phases show a fairly homogeneous pentlandite-rich composition typical for BMS formed via metasomatic reaction, whereas the 187Os/188Os compositions determined for 17 of these BMS are extremely heterogeneous ranging between 0.1037 and 0.1981. Analyses by LA-ICP-MS reveal at least two populations of BMS grains characterized by contrasting HSE patterns. One type of pattern is strongly enriched in the more compatible HSE Os, Ir, and Ru over the typically incompatible Pt, Pd, and Re, while the other type shows moderate enrichment of the more incompatible HSE and has overall lower compatible HSE/incompatible HSE composition. The small-scale heterogeneity observed in these BMS highlights the need for caution when utilizing the Re-Os system to date mantle events, as even depleted harzburgite samples such as 474527 are likely to have experienced a complex history of metasomatic overprinting, with uncertain effects on the HSE.

A dearth of intermediate melts at subduction zone volcanoes and the petrogenesis of arc andesites.

PubMed

Reubi, Olivier; Blundy, Jon

2009-10-29

Andesites represent a large proportion of the magmas erupted at continental arc volcanoes and are regarded as a major component in the formation of continental crust. Andesite petrogenesis is therefore fundamental in terms of both volcanic hazard and differentiation of the Earth. Andesites typically contain a significant proportion of crystals showing disequilibrium petrographic characteristics indicative of mixing or mingling between silicic and mafic magmas, which fuels a long-standing debate regarding the significance of these processes in andesite petrogenesis and ultimately questions the abundance of true liquids with andesitic composition. Central to this debate is the distinction between liquids (or melts) and magmas, mixtures of liquids with crystals, which may or may not be co-genetic. With this distinction comes the realization that bulk-rock chemical analyses of petrologically complex andesites can lead to a blurred picture of the fundamental processes behind arc magmatism. Here we present an alternative view of andesite petrogenesis, based on a review of quenched glassy melt inclusions trapped in phenocrysts, whole-rock chemistry, and high-pressure and high-temperature experiments. We argue that true liquids of intermediate composition (59 to 66 wt% SiO(2)) are far less common in the sub-volcanic reservoirs of arc volcanoes than is suggested by the abundance of erupted magma within this compositional range. Effective mingling within upper crustal magmatic reservoirs obscures a compositional bimodality of melts ascending from the lower crust, and masks the fundamental role of silicic melts (>/=66 wt% SiO(2)) beneath intermediate arc volcanoes. This alternative view resolves several puzzling aspects of arc volcanism and provides important clues to the integration of plutonic and volcanic records.

Interactions between solidification and compositional convection in mushy layers

NASA Technical Reports Server (NTRS)

Worster, M. Grae

1994-01-01

Mushy layers are ubiquitous during the solidification of alloys. They are regions of mixed phase wherein solid crystals are bathed in the melt from which they grew. The matrix of crystals forms a porous medium through which the melt can flow, driven either by external forces or by its own buoyancy in a gravitational field. Buoyancy-driven convection of the melt depends both on temperature gradients, which are necessary for solidification, and on compositional gradients, which are generated as certain components of the alloy are preferentially incorporated in the solid phase and the remaining components are expelled into the melt. In fully liquid regions, the combined action of temperature and concentration on the density of the liquid can cause various forms of double-diffusive convection. However, in the interior of mushy regions the temperature and concentration are thermodynamically coupled so only single-diffusive convection can occur. Typically, the effect of composition on the buoyancy of the melt is much greater than the effect of temperature, and thus convection in mushy layers in driven primarily by the computational gradients within them. The rising interstitial liquid is relatively dilute, having come from colder regions of the mushy layer, where the liquidus concentration is lower, and can dissolve the crystal matrix through which it flows. This is the fundamental process by which chimneys are formed. It is a nonlinear process that requires the convective velocities to be sufficiently large, so fully fledged chimneys (narrow channels) might be avoided by means that weaken the flow. Better still would be to prevent convection altogether, since even weak convection will cause lateral, compositional inhomogeneities in castings. This report outlines three studies that examine the onset of convection within mushy layers.

Copper isotope fractionation during partial melting and melt percolation in the upper mantle: Evidence from massif peridotites in Ivrea-Verbano Zone, Italian Alps

NASA Astrophysics Data System (ADS)

Huang, Jian; Huang, Fang; Wang, Zaicong; Zhang, Xingchao; Yu, Huimin

2017-08-01

To investigate the behavior of Cu isotopes during partial melting and melt percolation in the mantle, we have analyzed Cu isotopic compositions of a suite of well-characterized Paleozoic peridotites from the Balmuccia and Baldissero massifs in the Ivrea-Verbano Zone (IVZ, Northern Italy). Our results show that fresh lherzolites and harzburgites have a large variation of δ65Cu ranging from -0.133 to 0.379‰, which are negatively correlated with Al2O3 contents as well as incompatible platinum-group (e.g., Pd) and chalcophile element (e.g., Cu, S, Se, and Te) contents. The high δ65Cu can be explained by Cu isotope fractionation during partial melting of a sulfide-bearing peridotite source, with the light isotope (63Cu) preferentially entering the melts. The low δ65Cu can be attributed to precipitation of sulfides enriched in 63Cu during sulfur-saturated melt percolation. Replacive dunites from the Balmuccia massif display high δ65Cu from 0.544 to 0.610‰ with lower Re, Pd, S, Se, and Te contents and lower Pd/Ir ratios relative to lherzolites, which may result from dissolution of sulfides during interactions between S-undersaturated melts and lherzolites at high melt/rock ratios. Thus, our results suggest that partial melting and melt percolation largely account for the Cu isotopic heterogeneity of the upper mantle. The correlation between δ65Cu and Cu contents of the lherzolites and harzburgites was used to model Cu isotope fractionation during partial melting of a sulfide-bearing peridotite, because Cu is predominantly hosted in sulfide. The modelling results indicate an isotope fractionation factor of αmelt-peridotite = 0.99980-0.99965 (i.e., 103lnαmelt-peridotite = -0.20 to -0.35‰). In order to explain the Cu isotopic systematics of komatiites and mid-ocean ridge basalts reported previously, the estimated αmelt-peridotite was used to simulate Cu isotopic variations in melts generated by variable degrees of mantle melting. The results suggest that high degrees (>25%) of partial melting extracts nearly all source Cu and it cannot produce Cu isotope fractionation in komatiites relative to their mantle source, and that sulfide segregation during magma evolution have modified Cu isotopic compositions of mid-ocean ridge basalts.

Evaluation of Graphite Fiber/Polyimide PMCs from Hot Melt vs Solution Prepreg

NASA Technical Reports Server (NTRS)

Shin, E. Eugene; Sutter, James K.; Eakin, Howard; Inghram, Linda; McCorkle, Linda; Scheiman, Dan; Papadopoulos, Demetrios; Thesken, John; Fink, Jeffrey E.

2002-01-01

Carbon fiber reinforced high temperature polymer matrix composites (PMC) have been extensively investigated as potential weight reduction replacements of various metallic components in next generation high performance propulsion rocket engines. The initial phase involves development of comprehensive composite material-process-structure-design-property-in-service performance correlations and database, especially for a high stiffness facesheet of various sandwich structures. Overview of the program plan, technical approaches and current multi-team efforts will be presented. During composite fabrication, it was found that the two large volume commercial prepregging methods (hot-melt vs. solution) resulted in considerably different composite cure behavior. Details of the process-induced physical and chemical modifications in the prepregs, their effects on composite processing, and systematic cure cycle optimization studies will be discussed. The combined effects of prepregging method and cure cycle modification on composite properties and isothermal aging performance were also evaluated.