50 CFR 300.132 - Lobster harvest limitations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... harvest limitations. (a) Berried lobsters. A berried (egg-bearing) lobster in treaty waters may not be retained on board. A berried lobster must be returned immediately to the water unharmed. A berried lobster... lobster smaller than the minimum size limit must be returned immediately to the water unharmed. ...

50 CFR 622.40 - Limitations on traps and pots.

Code of Federal Regulations, 2012 CFR

2012-10-01

... limited to tyre palm, hemp, jute, cotton, wool, or silk. (B) Ungalvanized or uncoated iron wire with a... plastic, used or possessed in the EEZ, must have a minimum mesh size of 2.0 inches (5.1 cm) in the...

Using Satellite Imagery to Assess Large-Scale Habitat Characteristics of Adirondack Park, New York, USA

NASA Astrophysics Data System (ADS)

McClain, Bobbi J.; Porter, William F.

2000-11-01

Satellite imagery is a useful tool for large-scale habitat analysis; however, its limitations need to be tested. We tested these limitations by varying the methods of a habitat evaluation for white-tailed deer ( Odocoileus virginianus) in the Adirondack Park, New York, USA, utilizing harvest data to create and validate the assessment models. We used two classified images, one with a large minimum mapping unit but high accuracy and one with no minimum mapping unit but slightly lower accuracy, to test the sensitivity of the evaluation to these differences. We tested the utility of two methods of assessment, habitat suitability index modeling, and pattern recognition modeling. We varied the scale at which the models were applied by using five separate sizes of analysis windows. Results showed that the presence of a large minimum mapping unit eliminates important details of the habitat. Window size is relatively unimportant if the data are averaged to a large resolution (i.e., township), but if the data are used at the smaller resolution, then the window size is an important consideration. In the Adirondacks, the proportion of hardwood and softwood in an area is most important to the spatial dynamics of deer populations. The low occurrence of open area in all parts of the park either limits the effect of this cover type on the population or limits our ability to detect the effect. The arrangement and interspersion of cover types were not significant to deer populations.

Methods for the preparation and analysis of solids and suspended solids for methylmercury

USGS Publications Warehouse

DeWild, John F.; Olund, Shane D.; Olson, Mark L.; Tate, Michael T.

2004-01-01

This report presents the methods and method performance data for the determination of methylmercury concentrations in solids and suspended solids. Using the methods outlined here, the U.S. Geological Survey's Wisconsin District Mercury Laboratory can consistently detect methylmercury in solids and suspended solids at environmentally relevant concentrations. Solids can be analyzed wet or freeze dried with a minimum detection limit of 0.08 ng/g (as-processed). Suspended solids must first be isolated from aqueous matrices by filtration. The minimum detection limit for suspended solids is 0.01 ng per filter resulting in a minimum reporting limit ranging from 0.2 ng/L for a 0.05 L filtered volume to 0.01 ng/L for a 1.0 L filtered volume. Maximum concentrations for both matrices can be extended to cover nearly any amount of methylmercury by limiting sample size.

On the use of big-bang method to generate low-energy structures of atomic clusters modeled with pair potentials of different ranges.

PubMed

Marques, J M C; Pais, A A C C; Abreu, P E

2012-02-05

The efficiency of the so-called big-bang method for the optimization of atomic clusters is analysed in detail for Morse pair potentials with different ranges; here, we have used Morse potentials with four different ranges, from long- ρ = 3) to short-ranged ρ = 14) interactions. Specifically, we study the efficacy of the method in discovering low-energy structures, including the putative global minimum, as a function of the potential range and the cluster size. A new global minimum structure for long-ranged ρ = 3) Morse potential at the cluster size of n= 240 is reported. The present results are useful to assess the maximum cluster size for each type of interaction where the global minimum can be discovered with a limited number of big-bang trials. Copyright © 2011 Wiley Periodicals, Inc.

The minimum or natural rate of flow and droplet size ejected by Taylor cone-jets: physical symmetries and scaling laws

NASA Astrophysics Data System (ADS)

Gañán-Calvo, A. M.; Rebollo-Muñoz, N.; Montanero, J. M.

2013-03-01

We aim to establish the scaling laws for both the minimum rate of flow attainable in the steady cone-jet mode of electrospray, and the size of the resulting droplets in that limit. Use is made of a small body of literature on Taylor cone-jets reporting precise measurements of the transported electric current and droplet size as a function of the liquid properties and flow rate. The projection of the data onto an appropriate non-dimensional parameter space maps a region bounded by the minimum rate of flow attainable in the steady state. To explain these experimental results, we propose a theoretical model based on the generalized concept of physical symmetry, stemming from the system time invariance (steadiness). A group of symmetries rising at the cone-to-jet geometrical transition determines the scaling for the minimum flow rate and related variables. If the flow rate is decreased below that minimum value, those symmetries break down, which leads to dripping. We find that the system exhibits two instability mechanisms depending on the nature of the forces arising against the flow: one dominated by viscosity and the other by the liquid polarity. In the former case, full charge relaxation is guaranteed down to the minimum flow rate, while in the latter the instability condition becomes equivalent to the symmetry breakdown by charge relaxation or separation. When cone-jets are formed without artificially imposing a flow rate, a microjet is issued quasi-steadily. The flow rate naturally ejected this way coincides with the minimum flow rate studied here. This natural flow rate determines the minimum droplet size that can be steadily produced by any electrohydrodynamic means for a given set of liquid properties.

Minimum principles in electromagnetic scattering by small aspherical particles

NASA Astrophysics Data System (ADS)

Kostinski, Alex B.; Mongkolsittisilp, Ajaree

2013-12-01

We consider the question of optimal shapes, e.g., those causing minimal extinction among all shapes of equal volume. Guided by the isoperimetric property of a sphere, relevant in the geometrical optics limit of scattering by large particles, we examine an analogous question in the low frequency approximation, seeking to disentangle electric and geometric contributions. To that end, we survey the literature on shape functionals and focus on ellipsoids, giving a simple discussion of spherical optimality for the coated ellipsoidal particle. Monotonic increase with asphericity in the low frequency regime for orientation-averaged induced dipole moments and scattering cross-sections is also shown. Additional physical insight is obtained from the Rayleigh-Gans (transparent) limit and eccentricity expansions. We propose connecting low and high frequency regimes in a single minimum principle valid for all size parameters, provided that reasonable size distributions of randomly oriented aspherical particles wash out the resonances for intermediate size parameters. This proposal is further supported by the sum rule for integrated extinction.

Effects of consumption-oriented versus trophy-oriented fisheries on Muskellunge population size structure in northern Wisconsin

USGS Publications Warehouse

Faust, Matthew D.; Hansen, Michael J.

2016-01-01

To determine whether a consumption-oriented fishery was compatible with a trophy-oriented fishery for Muskellunge Esox masquinongy, we modeled effects of a spearing fishery and recreational angling fishery on population size structure (i.e., numbers of fish ≥ 102, 114, and 127 cm) in northern Wisconsin. An individual-based simulation model was used to quantify the effect of harvest mortality at currently observed levels of recreational angling and tribal spearing fishery exploitation, along with simulated increases in exploitation, for three typical growth potentials (i.e., low, moderate, and high) of Muskellunge in northern Wisconsin across a variety of minimum length limits (i.e., 71, 102, 114, and 127 cm). Populations with moderate to high growth potential and minimum length limits ≥ 114 cm were predicted to have lower declines in numbers of trophy Muskellunge when subjected to angling-only and mixed fisheries at observed and increased levels of exploitation, which suggested that fisheries with disparate motivations may be able to coexist under certain conditions such as restrictive length limits and low levels of exploitation. However, for most Muskellunge populations in northern Wisconsin regulated by a 102-cm minimum length limit, both angling and spearing fisheries may reduce numbers of trophy Muskellunge as larger declines were predicted across all growth potentials. Our results may be useful if Muskellunge management options in northern Wisconsin are re-examined in the future.

50 CFR 648.83 - Multispecies minimum fish sizes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Multispecies minimum fish sizes. 648.83... Measures for the NE Multispecies and Monkfish Fisheries § 648.83 Multispecies minimum fish sizes. (a) Minimum fish sizes. (1) Minimum fish sizes for recreational vessels and charter/party vessels that are not...

50 CFR 648.103 - Minimum fish sizes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Minimum fish sizes. 648.103 Section 648... Summer Flounder Fisheries § 648.103 Minimum fish sizes. (a) The minimum size for summer flounder is 14... carrying more than five crew members. (c) The minimum sizes in this section apply to whole fish or to any...

50 CFR 648.124 - Minimum fish sizes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Minimum fish sizes. 648.124 Section 648... Scup Fishery § 648.124 Minimum fish sizes. (a) The minimum size for scup is 9 inches (22.9 cm) TL for... charter boat, or more than five crew members if a party boat. (c) The minimum size applies to whole fish...

50 CFR 648.93 - Monkfish minimum fish sizes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 12 2012-10-01 2012-10-01 false Monkfish minimum fish sizes. 648.93... Measures for the NE Multispecies and Monkfish Fisheries § 648.93 Monkfish minimum fish sizes. (a) General... fish size requirements established in this section. Minimum Fish Sizes (Total Length/Tail Length) Total...

50 CFR 648.93 - Monkfish minimum fish sizes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Monkfish minimum fish sizes. 648.93... Measures for the NE Multispecies and Monkfish Fisheries § 648.93 Monkfish minimum fish sizes. (a) General... fish size requirements established in this section. Minimum Fish Sizes (Total Length/Tail Length) Total...

50 CFR 648.93 - Monkfish minimum fish sizes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 10 2011-10-01 2011-10-01 false Monkfish minimum fish sizes. 648.93... Measures for the NE Multispecies and Monkfish Fisheries § 648.93 Monkfish minimum fish sizes. (a) General... fish size requirements established in this section. Minimum Fish Sizes (Total Length/Tail Length) Total...

50 CFR 648.93 - Monkfish minimum fish sizes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Monkfish minimum fish sizes. 648.93... Measures for the NE Multispecies and Monkfish Fisheries § 648.93 Monkfish minimum fish sizes. (a) General... fish size requirements established in this section. Minimum Fish Sizes (Total Length/Tail Length) Total...

Fundamental Physical Limits for the Size of Future Planetary Surface Exploration Systems

NASA Astrophysics Data System (ADS)

Andrews, F.; Hobbs, S. E.; Honstvet, I.; Snelling, M.

2004-04-01

With the current interest in the potential use of Nanotechnology for spacecraft, it becomes increasingly likely that environmental sensor probes, such as the "lab-on-a-chip" concept, will take advantage of this technology and become orders of magnitude smaller than current sensor systems. This paper begins to investigate how small these systems could theoretically become, and what are the governing laws and limiting factors that determine that minimum size. The investigation focuses on the three primary subsystems for a sensor network of this nature Sensing, Information Processing and Communication. In general, there are few fundamental physical laws that limit the size of the sensor system. Limits tend to be driven by factors other than the laws of physics. These include user requirements, such as the acceptable probability of error, and the potential external environment.

Voltage scheduling for low power/energy

NASA Astrophysics Data System (ADS)

Manzak, Ali

2001-07-01

Power considerations have become an increasingly dominant factor in the design of both portable and desk-top systems. An effective way to reduce power consumption is to lower the supply voltage since voltage is quadratically related to power. This dissertation considers the problem of lowering the supply voltage at (i) the system level and at (ii) the behavioral level. At the system level, the voltage of the variable voltage processor is dynamically changed with the work load. Processors with limited sized buffers as well as those with very large buffers are considered. Given the task arrival times, deadline times, execution times, periods and switching activities, task scheduling algorithms that minimize energy or peak power are developed for the processors equipped with very large buffers. A relation between the operating voltages of the tasks for minimum energy/power is determined using the Lagrange multiplier method, and an iterative algorithm that utilizes this relation is developed. Experimental results show that the voltage assignment obtained by the proposed algorithm is very close (0.1% error) to that of the optimal energy assignment and the optimal peak power (1% error) assignment. Next, on-line and off-fine minimum energy task scheduling algorithms are developed for processors with limited sized buffers. These algorithms have polynomial time complexity and present optimal (off-line) and close-to-optimal (on-line) solutions. A procedure to calculate the minimum buffer size given information about the size of the task (maximum, minimum), execution time (best case, worst case) and deadlines is also presented. At the behavioral level, resources operating at multiple voltages are used to minimize power while maintaining the throughput. Such a scheme has the advantage of allowing modules on the critical paths to be assigned to the highest voltage levels (thus meeting the required timing constraints) while allowing modules on non-critical paths to be assigned to lower voltage levels (thus reducing the power consumption). A polynomial time resource and latency constrained scheduling algorithm is developed to distribute the available slack among the nodes such that power consumption is minimum. The algorithm is iterative and utilizes the slack based on the Lagrange multiplier method.

50 CFR 648.165 - Bluefish minimum fish sizes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Bluefish minimum fish sizes. 648.165... Measures for the Atlantic Bluefish Fishery § 648.165 Bluefish minimum fish sizes. If the MAFMC determines through its annual review or framework adjustment process that minimum fish sizes are necessary to ensure...

50 CFR 648.165 - Bluefish minimum fish sizes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Bluefish minimum fish sizes. 648.165... Measures for the Atlantic Bluefish Fishery § 648.165 Bluefish minimum fish sizes. If the MAFMC determines through its annual review or framework adjustment process that minimum fish sizes are necessary to ensure...

50 CFR 648.165 - Bluefish minimum fish sizes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 12 2012-10-01 2012-10-01 false Bluefish minimum fish sizes. 648.165... Measures for the Atlantic Bluefish Fishery § 648.165 Bluefish minimum fish sizes. If the MAFMC determines through its annual review or framework adjustment process that minimum fish sizes are necessary to ensure...

50 CFR 648.162 - Minimum fish sizes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Minimum fish sizes. 648.162 Section 648... Atlantic Bluefish Fishery § 648.162 Minimum fish sizes. If the Council determines through its annual review or framework adjustment process that minimum fish sizes are necessary to assure that the fishing...

Comparisons of body sizes at sexual maturity and at sex change in the parrotfishes of Hawaii: input needed for management regulations and stock assessments.

PubMed

DeMartini, E E; Howard, K G

2016-02-01

First estimates of sex allocation patterns and body size-at-sexual maturity and at protogynous sex change are presented for the five major (including one endemic) species of parrotfishes of Hawaii. Median body size at initial maturation as a female (LM50) and at protogynous sex change from adult female to adult male (LΔ50) varied greatly among the five species. Estimates of LM50 were about 14, 17, 24, 34 and 35 cm fork length (LF) in palenose Scarus psittacus, Pacific bullethead Chlorurus spilurus, stareye Calotomus carolinus, spectacled Chlorurus perspicillatus and redlip parrotfish Scarus rubroviolaceus. Values of LΔ50 were c. 23, 27, 37, 46 and 47 cm LF in the respective species. Length at female maturation was proportional to maximum body size (Lmax) of the respective species, ranging from 50 to 72% and averaging 62% of Lmax across species. LΔ50 was also proportional to Lmax, ranging from 82 to 97% and averaging 92%. Males of both pairs of Scarus and Chlorurus spp. reported here are diandric. Only one of the five major species (C. carolinus) is functionally monandric, with either all or nearly all males secondarily derived from adult females. The broadly differing absolute body sizes at sexual maturation and at sex change among the five species have important implications for improving regulatory size limits for parrotfishes in the State of Hawaii, where parrotfish species have historically been managed based on a single minimum size limit of 30·5 cm LF. This study provides a model demonstration of why catch data for parrotfishes, and other size-structured reef-fish populations, should be recorded either by species or by functional size-groups of species that allow setting more meaningful minimum size limits. © 2016 The Fisheries Society of the British Isles.

Physical requirements and milestones for the HIT-PoP Experiment

NASA Astrophysics Data System (ADS)

Jarboe, Thomas

2011-10-01

Recent success with HIT-SI demonstrates the viability of steady inductive helicity injection (SIHI) as a spheromak formation and sustainment method. Results include the sustainment of toroidal current of over 50 kA, up to 40 kA of plasma current that is separate from the injectors, toroidal flux up to 6 times the peak injected flux, and j/n > 1014Am. All were achieved with 10MW or less applied power. This paper explores the requirements for a confinement test of the concept using a larger proof of principle experiment. The confinement experiment must not exceed the beta limit, the drift parameter limit, or the wall loading limit, where the drift parameter is (drift of electrons relative to ions to produce current)/(ion thermal speed). It must also exceed a minimum j/n, a minimum n a, and a minimum electron temperature, where a is the minor radius. The drift parameter limit and beta limit appear to play defining roles in spheromak performance leading to a very favorable scaling of wall loading with size. The milestones sequence suggested is the following: 1. Startup at drift parameter and beta limit minimum density. 2. Raise current until j/n exceeds 10-14Am. 3. Raise the current and temperature until T ~ 50 eV for good ionization. 4. Raise the current and density until n a > 2x1019 m-2 for neutral screening. 5. Raise current and temperature until T > 200eV so magnetic confinement can be studied.

50 CFR 648.126 - Scup minimum fish sizes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Scup minimum fish sizes. 648.126 Section... Scup Fishery § 648.126 Scup minimum fish sizes. (a) Moratorium (commercially) permitted vessels. The... whole fish or any part of a fish found in possession, e.g., fillets. These minimum sizes may be adjusted...

50 CFR 648.126 - Scup minimum fish sizes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 12 2012-10-01 2012-10-01 false Scup minimum fish sizes. 648.126 Section... Scup Fishery § 648.126 Scup minimum fish sizes. (a) Moratorium (commercially) permitted vessels. The... whole fish or any part of a fish found in possession, e.g., fillets. These minimum sizes may be adjusted...

50 CFR 648.126 - Scup minimum fish sizes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Scup minimum fish sizes. 648.126 Section... Scup Fishery § 648.126 Scup minimum fish sizes. (a) Moratorium (commercially) permitted vessels. The... whole fish or any part of a fish found in possession, e.g., fillets. These minimum sizes may be adjusted...

Gigantism, temperature and metabolic rate in terrestrial poikilotherms

PubMed Central

Makarieva, Anastassia M; Gorshkov, Victor G; Li, Bai-Lian

2005-01-01

The mechanisms dictating upper limits to animal body size are not well understood. We have analysed body length data for the largest representatives of 24 taxa of terrestrial poikilotherms from tropical, temperate and polar environments. We find that poikilothermic giants on land become two–three times shorter per each 10 degrees of decrease in ambient temperature. We quantify that this diminution of maximum body size accurately compensates the drop of metabolic rate dictated by lower temperature. This supports the idea that the upper limit to body size within each taxon can be set by a temperature-independent critical minimum value of mass-specific metabolic rate, a fall below which is not compatible with successful biological performance. PMID:16191647

Three Essays In and Tests of Theoretical Urban Economics

NASA Astrophysics Data System (ADS)

Zhao, Weihua

This dissertation consists of three essays on urban economics. The three essays are related to urban spatial structure change, energy consumption, greenhouse gas emissions, and housing redevelopment. Chapter 1 answers the question: Does the classic Standard Urban Model still describe the growth of cities? Chapter 2 derives the implications of telework on urban spatial structure, energy consumption, and greenhouse gas emissions. Chapter 3 investigates the long run effects of minimum lot size zoning on neighborhood redevelopment. Chapter 1 identifies a new implication of the classic Standard Urban Model, the "unitary elasticity property (UEP)", which is the sum of the elasticity of central density and the elasticity of land area with respect to population change is approximately equal to unity. When this implication of the SUM is tested, it fits US cities fairly well. Further analysis demonstrates that topographic barriers and age of housing stock are the key factors explaining deviation from the UEP. Chapter 2 develops a numerical urban simulation model with households that are able to telework to investigate the urban form, congestion, energy consumption and greenhouse gas emission implications of telework. Simulation results suggest that by reducing transportation costs, telework causes sprawl, with associated longer commutes and consumption of larger homes, both of which increase energy consumption. Overall effects depend on who captures the gains from telework (workers versus firms), urban land use regulation such as height limits or greenbelts, and the fraction of workers participating in telework. The net effects of telework on energy use and GHG emissions are generally negligible. Chapter 3 applies dynamic programming to investigate the long run effects of minimum lot size zoning on neighborhood redevelopment. With numerical simulation, comparative dynamic results show that minimum lot size zoning can delay initial land conversion and slow down demolition and housing redevelopment. Initially, minimum lot size zoning is not binding. However, as city grows, it becomes binding and can effectively distort housing supply. It can lower both floor area ratio and residential density, and reduce aggregate housing supply. Overall, minimum lot size zoning can stabilize the path of structure/land ratios, housing service levels, structure density, and housing prices. In addition, minimum lot size zoning provides more incentive for developer to maintain the building, slow structure deterioration, and raise the minimum level of housing services provided over the life cycle of development.

Hedge math: Theoretical limits on minimum stockpile size across nuclear hedging strategies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lafleur, Jarret Marshall; Roesler, Alexander W.

2016-09-01

In June 2013, the Department of Defense published a congressionally mandated, unclassified update on the U.S. Nuclear Employment Strategy. Among the many updates in this document are three key ground rules for guiding the sizing of the non-deployed U.S. nuclear stockpile. Furthermore, these ground rules form an important and objective set of criteria against which potential future stockpile hedging strategies can be evaluated.

Automated predesign of aircraft

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.; Kruse, G. S.; Tanner, C. J.; Wilson, P. J.

1978-01-01

Program uses multistation structural-synthesis to size and design box-beam structures for transport aircraft. Program optimizes static strength and scales up to satisfy fatigue and fracture criteria. It has multimaterial capability and library of materials properties, including advanced composites. Program can be used to evaluate impact on weight of variables such as materials, types of construction, structural configurations, minimum gage limits, applied loads, fatigue lives, crack-growth lives, initial crack sizes, and residual strengths.

50 CFR 648.147 - Black sea bass minimum fish sizes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Black sea bass minimum fish sizes. 648... Measures for the Black Sea Bass Fishery § 648.147 Black sea bass minimum fish sizes. (a) Moratorium (commercially) permitted vessels. The minimum size for black sea bass is 11 inches (27.94 cm) total length for...

50 CFR 648.147 - Black sea bass minimum fish sizes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 12 2012-10-01 2012-10-01 false Black sea bass minimum fish sizes. 648... Measures for the Black Sea Bass Fishery § 648.147 Black sea bass minimum fish sizes. (a) Moratorium (commercially) permitted vessels. The minimum size for black sea bass is 11 inches (27.94 cm) total length for...

50 CFR 648.147 - Black sea bass minimum fish sizes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Black sea bass minimum fish sizes. 648... Measures for the Black Sea Bass Fishery § 648.147 Black sea bass minimum fish sizes. (a) Moratorium (commercially) permitted vessels. The minimum size for black sea bass is 11 inches (27.94 cm) total length for...

50 CFR 648.124 - Minimum fish sizes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 10 2011-10-01 2011-10-01 false Minimum fish sizes. 648.124 Section 648... Scup Fishery § 648.124 Minimum fish sizes. Link to an amendment published at 76 FR 60633, Sept. 29... if a party boat. (c) The minimum size applies to whole fish or any part of a fish found in possession...

Passive Rocket Diffuser Theory: A Re-Examination of Minimum Second Throat Size

NASA Technical Reports Server (NTRS)

Jones, Daniel R.

2016-01-01

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure during testing without using active control systems. Among the most critical design parameters is the relative area of the diffuser throat to that of the nozzle throat. A smaller second throat is generally desirable because it decreases the stagnation-to-ambient pressure ratio the diffuser requires for nominal operation. There is a limit, however. Below a certain size, the second throat can cause pressure buildup within the diffuser and prevent it from reaching the start condition that protects the nozzle from side-load damage. This paper presents a method for improved estimation of the minimum second throat area which enables diffuser start. The new 3-zone model uses traditional quasi-one-dimensional compressible flow theory to approximate the structure of two distinct diffuser flow fields observed in Computational Fluid Dynamics (CFD) simulations and combines them to provide a less-conservative estimate of the second throat size limit. It is unique among second throat sizing methods in that it accounts for all major conical nozzle and second throat diffuser design parameters within its limits of application. The performance of the 3-zone method is compared to the historical normal shock and force balance methods, and verified against a large number of CFD simulations at specific heat ratios of 1.4 and 1.25. Validation is left as future work, and the model is currently intended to function only as a first-order design tool.

78 FR 44461 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Snapper-Grouper Fishery off the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-24

... discards of red snapper (fish returned to the water because they are less than the minimum size limit). Red... to the water. Prohibiting the release of red snapper caught within the bag limits was discussed by... inches (76.2 cm), TL, or larger, in the South Atlantic off Florida, and red snapper and vermilion snapper...

"PowerUp"!: A Tool for Calculating Minimum Detectable Effect Sizes and Minimum Required Sample Sizes for Experimental and Quasi-Experimental Design Studies

ERIC Educational Resources Information Center

Dong, Nianbo; Maynard, Rebecca

2013-01-01

This paper and the accompanying tool are intended to complement existing supports for conducting power analysis tools by offering a tool based on the framework of Minimum Detectable Effect Sizes (MDES) formulae that can be used in determining sample size requirements and in estimating minimum detectable effect sizes for a range of individual- and…

Atomistic modeling of dropwise condensation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sikarwar, B. S., E-mail: bssikarwar@amity.edu; Singh, P. L.; Muralidhar, K.

The basic aim of the atomistic modeling of condensation of water is to determine the size of the stable cluster and connect phenomena occurring at atomic scale to the macroscale. In this paper, a population balance model is described in terms of the rate equations to obtain the number density distribution of the resulting clusters. The residence time is taken to be large enough so that sufficient time is available for all the adatoms existing in vapor-phase to loose their latent heat and get condensed. The simulation assumes clusters of a given size to be formed from clusters of smallermore » sizes, but not by the disintegration of the larger clusters. The largest stable cluster size in the number density distribution is taken to be representative of the minimum drop radius formed in a dropwise condensation process. A numerical confirmation of this result against predictions based on a thermodynamic model has been obtained. Results show that the number density distribution is sensitive to the surface diffusion coefficient and the rate of vapor flux impinging on the substrate. The minimum drop radius increases with the diffusion coefficient and the impinging vapor flux; however, the dependence is weak. The minimum drop radius predicted from thermodynamic considerations matches the prediction of the cluster model, though the former does not take into account the effect of the surface properties on the nucleation phenomena. For a chemically passive surface, the diffusion coefficient and the residence time are dependent on the surface texture via the coefficient of friction. Thus, physical texturing provides a means of changing, within limits, the minimum drop radius. The study reveals that surface texturing at the scale of the minimum drop radius does not provide controllability of the macro-scale dropwise condensation at large timescales when a dynamic steady-state is reached.« less

50 CFR 648.72 - Minimum surf clam size.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Atlantic Surf Clam and Ocean Quahog Fisheries § 648.72 Minimum surf clam size. (a) Minimum length. The minimum length for surf clams is 4.75 inches (12.065 cm). (b) Determination of compliance. No more than 50... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Minimum surf clam size. 648.72 Section 648...

Lack of size selectivity for paddlefish captured in hobbled gillnets

USGS Publications Warehouse

Scholten, G.D.; Bettoli, P.W.

2007-01-01

A commercial fishery for paddlefish Polyodon spathula caviar exists in Kentucky Lake, a reservoir on the lower Tennessee River. A 152-mm (bar-measure) minimum mesh size restriction on entanglement gear was enacted in 2002 and the minimum size limit was increased to 864 mm eye-fork length to reduce the possibility of recruitment overfishing. Paddlefish were sampled in 2003-2004 using experimental monofilament gillnets with panels of 89, 102, 127, 152, 178, and 203-mm meshes and the efficacy of the mesh size restriction was evaluated. Following the standards of commercial gear used in that fishery, nets were "hobbled" (i.e., 128 m ?? 3.6 m nets were tied down to 2.4 m; 91 m ?? 9.1 m nets were tied down to 7.6 m). The mean lengths of paddlefish (Ntotal = 576 fish) captured in each mesh were similar among most meshes and bycatch rates of sublegal fish did not vary with mesh size. Selectivity curves could not be modeled because the mean and modal lengths of fish captured in each mesh did not increase with mesh size. Ratios of fish girth to mesh perimeter (G:P) for individual fish were often less than 1.0 as a result of the largest meshes capturing small paddlefish. It is unclear whether lack of size selectivity for paddlefish was because the gillnets were hobbled, the unique morphology of paddlefish, or the fact that they swim with their mouths agape when filter feeding. The lack of size selectivity by hobbled gillnets fished in Kentucky Lake means that managers cannot influence the size of paddlefish captured by commercial gillnet gear by changing minimum mesh size regulations. ?? 2006 Elsevier B.V. All rights reserved.

48 CFR 52.247-61 - F.o.b. Origin-Minimum Size of Shipments.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false F.o.b. Origin-Minimum Size... Clauses 52.247-61 F.o.b. Origin—Minimum Size of Shipments. As prescribed in 47.305-16(c), insert the following clause in solicitations and contracts when volume rates may apply: F.o.b. Origin—Minimum Size of...

77 FR 4754 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Snapper-Grouper Fishery off the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-31

... recreational annual catch limits (ACLs) have been met before the end of the fishing year for the past 3 fishing... lb (1,134 kg), round weight; and (3) the South Atlantic Unlimited Snapper-Grouper Permit must have... minimum size limit from 12 inches (30.5 cm), total length (TL) to 13 inches (33 cm), TL, and to increase...

The provision of clearances accuracy in piston - cylinder mating

NASA Astrophysics Data System (ADS)

Glukhov, V. I.; Shalay, V. V.

2017-08-01

The paper is aimed at increasing the quality of the pumping equipment in oil and gas industry. The main purpose of the study is to stabilize maximum values of productivity and durability of the pumping equipment based on the selective assembly of the cylinder-piston kinematic mating by optimization criterion. It is shown that the minimum clearance in the piston-cylinder mating is formed by maximum material dimensions. It is proved that maximum material dimensions are characterized by their own laws of distribution within the tolerance limits for the diameters of the cylinder internal mirror and the outer cylindrical surface of the piston. At that, their dispersion zones should be divided into size groups with a group tolerance equal to half the tolerance for the minimum clearance. The techniques for measuring the material dimensions - the smallest cylinder diameter and the largest piston diameter according to the envelope condition - are developed for sorting them into size groups. Reliable control of the dimensions precision ensures optimal minimum clearances of the piston-cylinder mating in all the size groups of the pumping equipment, necessary for increasing the equipment productivity and durability during the production, operation and repair processes.

50 CFR 648.93 - Monkfish minimum fish sizes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Monkfish minimum fish sizes. 648.93... Measures for the NE Multispecies and Monkfish Fisheries § 648.93 Monkfish minimum fish sizes. (a) General provisions. All monkfish caught by vessels issued a valid Federal monkfish permit must meet the minimum fish...

50 CFR 697.20 - Size, harvesting and landing requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... length. (1) The minimum carapace length for all American lobsters harvested in or from the EEZ Nearshore... length for all American lobsters landed, harvested, or possessed by vessels issued a Federal limited access American lobster permit fishing in or electing to fish in the Nearshore Management Area 1 or the...

50 CFR 640.27 - Spiny lobster import prohibitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 10 2011-10-01 2011-10-01 false Spiny lobster import prohibitions. 640.27... ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE SPINY LOBSTER FISHERY OF THE GULF OF MEXICO AND SOUTH ATLANTIC Management Measures § 640.27 Spiny lobster import prohibitions. (a) Minimum size limits for...

50 CFR 697.20 - Size, harvesting and landing requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... length. (1) The minimum carapace length for all American lobsters harvested in or from the EEZ Nearshore... length for all American lobsters landed, harvested, or possessed by vessels issued a Federal limited access American lobster permit fishing in or electing to fish in the Nearshore Management Area 1 or the...

50 CFR 640.27 - Spiny lobster import prohibitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Spiny lobster import prohibitions. 640.27... ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE SPINY LOBSTER FISHERY OF THE GULF OF MEXICO AND SOUTH ATLANTIC Management Measures § 640.27 Spiny lobster import prohibitions. (a) Minimum size limits for...

Quantifying environmental limiting factors on tree cover using geospatial data.

PubMed

Greenberg, Jonathan A; Santos, Maria J; Dobrowski, Solomon Z; Vanderbilt, Vern C; Ustin, Susan L

2015-01-01

Environmental limiting factors (ELFs) are the thresholds that determine the maximum or minimum biological response for a given suite of environmental conditions. We asked the following questions: 1) Can we detect ELFs on percent tree cover across the eastern slopes of the Lake Tahoe Basin, NV? 2) How are the ELFs distributed spatially? 3) To what extent are unmeasured environmental factors limiting tree cover? ELFs are difficult to quantify as they require significant sample sizes. We addressed this by using geospatial data over a relatively large spatial extent, where the wall-to-wall sampling ensures the inclusion of rare data points which define the minimum or maximum response to environmental factors. We tested mean temperature, minimum temperature, potential evapotranspiration (PET) and PET minus precipitation (PET-P) as potential limiting factors on percent tree cover. We found that the study area showed system-wide limitations on tree cover, and each of the factors showed evidence of being limiting on tree cover. However, only 1.2% of the total area appeared to be limited by the four (4) environmental factors, suggesting other unmeasured factors are limiting much of the tree cover in the study area. Where sites were near their theoretical maximum, non-forest sites (tree cover < 25%) were primarily limited by cold mean temperatures, open-canopy forest sites (tree cover between 25% and 60%) were primarily limited by evaporative demand, and closed-canopy forests were not limited by any particular environmental factor. The detection of ELFs is necessary in order to fully understand the width of limitations that species experience within their geographic range.

50 CFR 648.83 - Multispecies minimum fish sizes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... vessels are subject to the following minimum fish sizes, determined by total length (TL): Minimum Fish Sizes (TL) for Commercial Vessels Species Size(inches) Cod 22 (55.9 cm) Haddock 18 (45.7 cm) Pollock 19 (48.3 cm) Witch flounder (gray sole) 14 (35.6 cm) Yellowtail flounder 13 (33.0 cm) American plaice...

50 CFR 648.83 - Multispecies minimum fish sizes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... vessels are subject to the following minimum fish sizes, determined by total length (TL): Minimum Fish Sizes (TL) for Commercial Vessels Species Size(inches) Cod 19 (48.3 cm) Haddock 16 (40.6 cm) Pollock 19 (48.3 cm) Witch flounder (gray sole) 13 (33 cm) Yellowtail flounder 12 (30.5 cm) American plaice (dab...

50 CFR 648.83 - Multispecies minimum fish sizes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... vessels are subject to the following minimum fish sizes, determined by total length (TL): Minimum Fish Sizes (TL) for Commercial Vessels Species Size(inches) Cod 19 (48.3 cm) Haddock 16 (40.6 cm) Pollock 19 (48.3 cm) Witch flounder (gray sole) 13 (33 cm) Yellowtail flounder 12 (30.5 cm) American plaice (dab...

50 CFR 648.83 - Multispecies minimum fish sizes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... vessels are subject to the following minimum fish sizes, determined by total length (TL): Minimum Fish Sizes (TL) for Commercial Vessels Species Size(inches) Cod 22 (55.9 cm) Haddock 18 (45.7 cm) Pollock 19 (48.3 cm) Witch flounder (gray sole) 14 (35.6 cm) Yellowtail flounder 13 (33.0 cm) American plaice...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Altabet, Y. Elia; Debenedetti, Pablo G., E-mail: pdebene@princeton.edu; Stillinger, Frank H.

In particle systems with cohesive interactions, the pressure-density relationship of the mechanically stable inherent structures sampled along a liquid isotherm (i.e., the equation of state of an energy landscape) will display a minimum at the Sastry density ρ{sub S}. The tensile limit at ρ{sub S} is due to cavitation that occurs upon energy minimization, and previous characterizations of this behavior suggested that ρ{sub S} is a spinodal-like limit that separates all homogeneous and fractured inherent structures. Here, we revisit the phenomenology of Sastry behavior and find that it is subject to considerable finite-size effects, and the development of the inherentmore » structure equation of state with system size is consistent with the finite-size rounding of an athermal phase transition. What appears to be a continuous spinodal-like point at finite system sizes becomes discontinuous in the thermodynamic limit, indicating behavior akin to a phase transition. We also study cavitation in glassy packings subjected to athermal expansion. Many individual expansion trajectories averaged together produce a smooth equation of state, which we find also exhibits features of finite-size rounding, and the examples studied in this work give rise to a larger limiting tension than for the corresponding landscape equation of state.« less

Developing recreational harvest regulations for an unexploited lake trout population

USGS Publications Warehouse

Lenker, Melissa A; Weidel, Brian C.; Jensen, Olaf P.; Solomon, Christopher T.

2016-01-01

Developing fishing regulations for previously unexploited populations presents numerous challenges, many of which stem from a scarcity of baseline information about abundance, population productivity, and expected angling pressure. We used simulation models to test the effect of six management strategies (catch and release; trophy, minimum, and maximum length limits; and protected and exploited slot length limits) on an unexploited population of Lake Trout Salvelinus namaycush in Follensby Pond, a 393-ha lake located in New York State’s Adirondack Park. We combined field and literature data and mark–recapture abundance estimates to parameterize an age-structured population model and used the model to assess the effects of each management strategy on abundance, catch per unit effort (CPUE), and harvest over a range of angler effort (0–2,000 angler-days/year). Lake Trout density (3.5 fish/ha for fish ≥ age 13, the estimated age at maturity) was similar to densities observed in other unexploited systems, but growth rate was relatively slow. Maximum harvest occurred at levels of effort ≤ 1,000 angler-days/year in all the scenarios considered. Regulations that permitted harvest of large postmaturation fish, such as New York’s standard Lake Trout minimum size limit or a trophy size limit, resulted in low harvest and high angler CPUE. Regulations that permitted harvest of small and sometimes immature fish, such as a protected slot or maximum size limit, allowed high harvest but resulted in low angler CPUE and produced rapid declines in harvest with increases in effort beyond the effort consistent with maximum yield. Management agencies can use these results to match regulations to management goals and to assess the risks of different management options for unexploited Lake Trout populations and other fish species with similar life history traits.

Determining size and dispersion of minimum viable populations for land management planning and species conservation

NASA Astrophysics Data System (ADS)

Lehmkuhl, John F.

1984-03-01

The concept of minimum populations of wildlife and plants has only recently been discussed in the literature. Population genetics has emerged as a basic underlying criterion for determining minimum population size. This paper presents a genetic framework and procedure for determining minimum viable population size and dispersion strategies in the context of multiple-use land management planning. A procedure is presented for determining minimum population size based on maintenance of genetic heterozygosity and reduction of inbreeding. A minimum effective population size ( N e ) of 50 breeding animals is taken from the literature as the minimum shortterm size to keep inbreeding below 1% per generation. Steps in the procedure adjust N e to account for variance in progeny number, unequal sex ratios, overlapping generations, population fluctuations, and period of habitat/population constraint. The result is an approximate census number that falls within a range of effective population size of 50 500 individuals. This population range defines the time range of short- to long-term population fitness and evolutionary potential. The length of the term is a relative function of the species generation time. Two population dispersion strategies are proposed: core population and dispersed population.

50 CFR 648.233 - Minimum Fish Sizes. [Reserved

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Minimum Fish Sizes. [Reserved] 648.233 Section 648.233 Wildlife and Fisheries FISHERY CONSERVATION AND MANAGEMENT, NATIONAL OCEANIC AND... Measures for the Spiny Dogfish Fishery § 648.233 Minimum Fish Sizes. [Reserved] ...

50 CFR 622.208 - Minimum mesh size applicable to rock shrimp off Georgia and Florida.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Minimum mesh size applicable to rock... mesh size applicable to rock shrimp off Georgia and Florida. (a) The minimum mesh size for the cod end of a rock shrimp trawl net in the South Atlantic EEZ off Georgia and Florida is 17/8 inches (4.8 cm...

50 CFR 622.208 - Minimum mesh size applicable to rock shrimp off Georgia and Florida.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Minimum mesh size applicable to rock... mesh size applicable to rock shrimp off Georgia and Florida. (a) The minimum mesh size for the cod end of a rock shrimp trawl net in the South Atlantic EEZ off Georgia and Florida is 17/8 inches (4.8 cm...

Two cell-counting factors regulate the aggregate size of the cellular slime mold Dictyostelium discoideum.

PubMed

Okuwa, T; Katayama, T; Takano, A; Kodaira, K; Yasukawa, H

2001-12-01

Countin, a cell-counting factor in Dictyostelium discoideum, is considered to limit the maximum size of the multicellular structure, because a countin null strain forms a huge fruiting body compared to that of the wild-type. A novel gene, countin2, that is highly homologous to countin (40% identity in amino acid sequence) was identified in the D. discoideum genome. The countin2 null strain formed a 1.7-fold higher number of the aggregates, resulting in smaller fruiting bodies compared with those of wild-type cells. Thus, the Countin2 protein is thought to limit the minimum size of the multicellular structure. The size and number of aggregates formed by a mixture of countin null and countin2 null strains were the same as those of the wild-type. These findings demonstrate that a combination of Countin and Countin2 proteins determines the appropriate size of the multicellular structure of D. discoideum.

50 CFR 300.122 - Relation to other laws.

Code of Federal Regulations, 2013 CFR

2013-10-01

... REGULATIONS Vessels of the United States Fishing in Colombian Treaty Waters § 300.122 Relation to other laws... placed under the command of a person who is not a citizen of the United States. (b) Minimum size limitations for certain species, such as reef fish in the Gulf of Mexico, may apply to vessels transiting the...

50 CFR 300.122 - Relation to other laws.

Code of Federal Regulations, 2011 CFR

2011-10-01

... REGULATIONS Vessels of the United States Fishing in Colombian Treaty Waters § 300.122 Relation to other laws... placed under the command of a person who is not a citizen of the United States. (b) Minimum size limitations for certain species, such as reef fish in the Gulf of Mexico, may apply to vessels transiting the...

50 CFR 300.122 - Relation to other laws.

Code of Federal Regulations, 2010 CFR

2010-10-01

... REGULATIONS Vessels of the United States Fishing in Colombian Treaty Waters § 300.122 Relation to other laws... placed under the command of a person who is not a citizen of the United States. (b) Minimum size limitations for certain species, such as reef fish in the Gulf of Mexico, may apply to vessels transiting the...

50 CFR 300.122 - Relation to other laws.

Code of Federal Regulations, 2014 CFR

2014-10-01

... REGULATIONS Vessels of the United States Fishing in Colombian Treaty Waters § 300.122 Relation to other laws... placed under the command of a person who is not a citizen of the United States. (b) Minimum size limitations for certain species, such as reef fish in the Gulf of Mexico, may apply to vessels transiting the...

50 CFR 300.122 - Relation to other laws.

Code of Federal Regulations, 2012 CFR

2012-10-01

... REGULATIONS Vessels of the United States Fishing in Colombian Treaty Waters § 300.122 Relation to other laws... placed under the command of a person who is not a citizen of the United States. (b) Minimum size limitations for certain species, such as reef fish in the Gulf of Mexico, may apply to vessels transiting the...

50 CFR 622.458 - Caribbean spiny lobster import prohibitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., AND SOUTH ATLANTIC Spiny Lobster Fishery of Puerto Rico and the U.S. Virgin Islands § 622.458... applies any place subject to the jurisdiction of the United States other than Puerto Rico or the U.S. Virgin Islands, and a more restrictive minimum size limit that applies to Puerto Rico and the U.S. Virgin...

76 FR 56322 - Atlantic Surfclam and Ocean Quahog Fisheries; 2012 Fishing Quotas for Atlantic Surfclams and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-13

.... 101013504-0610-02] RIN 0648-XA529 Atlantic Surfclam and Ocean Quahog Fisheries; 2012 Fishing Quotas for.... ACTION: Temporary rule. SUMMARY: NMFS suspends the minimum size limit for Atlantic surfclams for the 2012... 2012 will remain status quo. Regulations governing these fisheries require NMFS to notify the public in...

78 FR 25047 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Snapper-Grouper Fishery Off the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-29

... regulatory discards of red snapper (fish returned to the water because they are below the minimum size limit... red snapper in 2010, as well as the closure of vermilion snapper to commercial harvest in September 2009, most likely caused this increase in participation. Vermilion snapper is the primary target...

50 CFR 622.458 - Caribbean spiny lobster import prohibitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., AND SOUTH ATLANTIC Spiny Lobster Fishery of Puerto Rico and the U.S. Virgin Islands § 622.458.... Virgin Islands, and a more restrictive minimum size limit that applies to Puerto Rico and the U.S. Virgin Islands. (1) No person may import a Caribbean spiny lobster with less than a 6-ounce (170-gram) tail...

The Elderly Population with Chronic Functional Disability: Implications for Home Care Eligibility.

ERIC Educational Resources Information Center

Stone, Robyn I.; Murtaugh, Christopher M.

1990-01-01

Assessed effect of changes in minimum number of activities of daily living (ALD) and instrumental activities of daily living (IADL) limitations, types of help, and duration of disability required on size of population potentially eligible for home care benefits. Only 411,000 elders met restrictive disability criteria; over 4 million would qualify…

Improved Time-Lapsed Angular Scattering Microscopy of Single Cells

NASA Astrophysics Data System (ADS)

Cannaday, Ashley E.

By measuring angular scattering patterns from biological samples and fitting them with a Mie theory model, one can estimate the organelle size distribution within many cells. Quantitative organelle sizing of ensembles of cells using this method has been well established. Our goal is to develop the methodology to extend this approach to the single cell level, measuring the angular scattering at multiple time points and estimating the non-nuclear organelle size distribution parameters. The diameters of individual organelle-size beads were successfully extracted using scattering measurements with a minimum deflection angle of 20 degrees. However, the accuracy of size estimates can be limited by the angular range detected. In particular, simulations by our group suggest that, for cell organelle populations with a broader size distribution, the accuracy of size prediction improves substantially if the minimum angle of detection angle is 15 degrees or less. The system was therefore modified to collect scattering angles down to 10 degrees. To confirm experimentally that size predictions will become more stable when lower scattering angles are detected, initial validations were performed on individual polystyrene beads ranging in diameter from 1 to 5 microns. We found that the lower minimum angle enabled the width of this delta-function size distribution to be predicted more accurately. Scattering patterns were then acquired and analyzed from single mouse squamous cell carcinoma cells at multiple time points. The scattering patterns exhibit angular dependencies that look unlike those of any single sphere size, but are well-fit by a broad distribution of sizes, as expected. To determine the fluctuation level in the estimated size distribution due to measurement imperfections alone, formaldehyde-fixed cells were measured. Subsequent measurements on live (non-fixed) cells revealed an order of magnitude greater fluctuation in the estimated sizes compared to fixed cells. With our improved and better-understood approach to single cell angular scattering, we are now capable of reliably detecting changes in organelle size predictions due to biological causes above our measurement error of 20 nm, which enables us to apply our system to future studies of the investigation of various single cell biological processes.

A cavitation transition in the energy landscape of simple cohesive liquids and glasses

NASA Astrophysics Data System (ADS)

Altabet, Y. Elia; Stillinger, Frank H.; Debenedetti, Pablo G.

2016-12-01

In particle systems with cohesive interactions, the pressure-density relationship of the mechanically stable inherent structures sampled along a liquid isotherm (i.e., the equation of state of an energy landscape) will display a minimum at the Sastry density ρS. The tensile limit at ρS is due to cavitation that occurs upon energy minimization, and previous characterizations of this behavior suggested that ρS is a spinodal-like limit that separates all homogeneous and fractured inherent structures. Here, we revisit the phenomenology of Sastry behavior and find that it is subject to considerable finite-size effects, and the development of the inherent structure equation of state with system size is consistent with the finite-size rounding of an athermal phase transition. What appears to be a continuous spinodal-like point at finite system sizes becomes discontinuous in the thermodynamic limit, indicating behavior akin to a phase transition. We also study cavitation in glassy packings subjected to athermal expansion. Many individual expansion trajectories averaged together produce a smooth equation of state, which we find also exhibits features of finite-size rounding, and the examples studied in this work give rise to a larger limiting tension than for the corresponding landscape equation of state.

46 CFR 111.60-4 - Minimum cable conductor size.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Minimum cable conductor size. 111.60-4 Section 111.60-4...-GENERAL REQUIREMENTS Wiring Materials and Methods § 111.60-4 Minimum cable conductor size. Each cable conductor must be #18 AWG (0.82 mm2) or larger except— (a) Each power and lighting cable conductor must be...

46 CFR 111.60-4 - Minimum cable conductor size.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Minimum cable conductor size. 111.60-4 Section 111.60-4...-GENERAL REQUIREMENTS Wiring Materials and Methods § 111.60-4 Minimum cable conductor size. Each cable conductor must be #18 AWG (0.82 mm2) or larger except— (a) Each power and lighting cable conductor must be...

50 CFR 648.75 - Shucking at sea and minimum surfclam size.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 12 2012-10-01 2012-10-01 false Shucking at sea and minimum surfclam size... Measures for the Atlantic Surf Clam and Ocean Quahog Fisheries § 648.75 Shucking at sea and minimum surfclam size. (a) Shucking at sea—(1) Observers. (i) The Regional Administrator may allow the shucking of...

50 CFR 648.75 - Shucking at sea and minimum surfclam size.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Shucking at sea and minimum surfclam size... Measures for the Atlantic Surf Clam and Ocean Quahog Fisheries § 648.75 Shucking at sea and minimum surfclam size. (a) Shucking at sea—(1) Observers. (i) The Regional Administrator may allow the shucking of...

50 CFR 648.75 - Shucking at sea and minimum surfclam size.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Shucking at sea and minimum surfclam size... Measures for the Atlantic Surf Clam and Ocean Quahog Fisheries § 648.75 Shucking at sea and minimum surfclam size. (a) Shucking at sea—(1) Observers. (i) The Regional Administrator may allow the shucking of...

40 CFR 1042.310 - Engine selection for Category 1 and Category 2 engines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Category 2 engines. (a) Determine minimum sample sizes as follows: (1) For Category 1 engines, the minimum sample size is one engine or one percent of the projected U.S.-directed production volume for all your Category 1 engine families, whichever is greater. (2) For Category 2 engines, the minimum sample size is...

Rail vs truck transport of biomass.

PubMed

Mahmudi, Hamed; Flynn, Peter C

2006-01-01

This study analyzes the economics of transshipping biomass from truck to train in a North American setting. Transshipment will only be economic when the cost per unit distance of a second transportation mode is less than the original mode. There is an optimum number of transshipment terminals which is related to biomass yield. Transshipment incurs incremental fixed costs, and hence there is a minimum shipping distance for rail transport above which lower costs/km offset the incremental fixed costs. For transport by dedicated unit train with an optimum number of terminals, the minimum economic rail shipping distance for straw is 170 km, and for boreal forest harvest residue wood chips is 145 km. The minimum economic shipping distance for straw exceeds the biomass draw distance for economically sized centrally located power plants, and hence the prospects for rail transport are limited to cases in which traffic congestion from truck transport would otherwise preclude project development. Ideally, wood chip transport costs would be lowered by rail transshipment for an economically sized centrally located power plant, but in a specific case in Alberta, Canada, the layout of existing rail lines precludes a centrally located plant supplied by rail, whereas a more versatile road system enables it by truck. Hence for wood chips as well as straw the economic incentive for rail transport to centrally located processing plants is limited. Rail transshipment may still be preferred in cases in which road congestion precludes truck delivery, for example as result of community objections.

Sizing procedures for sun-tracking PV system with batteries

NASA Astrophysics Data System (ADS)

Nezih Gerek, Ömer; Başaran Filik, Ümmühan; Filik, Tansu

2017-11-01

Deciding optimum number of PV panels, wind turbines and batteries (i.e. a complete renewable energy system) for minimum cost and complete energy balance is a challenging and interesting problem. In the literature, some rough data models or limited recorded data together with low resolution hourly averaged meteorological values are used to test the sizing strategies. In this study, active sun tracking and fixed PV solar power generation values of ready-to-serve commercial products are recorded throughout 2015-2016. Simultaneously several outdoor parameters (solar radiation, temperature, humidity, wind speed/direction, pressure) are recorded with high resolution. The hourly energy consumption values of a standard 4-person household, which is constructed in our campus in Eskisehir, Turkey, are also recorded for the same period. During sizing, novel parametric random process models for wind speed, temperature, solar radiation, energy demand and electricity generation curves are achieved and it is observed that these models provide sizing results with lower LLP through Monte Carlo experiments that consider average and minimum performance cases. Furthermore, another novel cost optimization strategy is adopted to show that solar tracking PV panels provide lower costs by enabling reduced number of installed batteries. Results are verified over real recorded data.

7 CFR 51.2952 - Size specifications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... specifications. Size shall be specified in accordance with the facts in terms of one of the following classifications: (a) Mammoth size. Mammoth size means walnuts of which not over 12 percent, by count, pass through... foregoing classifications, size of walnuts may be specified in terms of minimum diameter, or minimum and...

7 CFR 51.2952 - Size specifications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... specifications. Size shall be specified in accordance with the facts in terms of one of the following classifications: (a) Mammoth size. Mammoth size means walnuts of which not over 12 percent, by count, pass through... foregoing classifications, size of walnuts may be specified in terms of minimum diameter, or minimum and...

76 FR 67656 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Reef Fish Fishery of the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-02

... under the rebuilding plan assume a proportional reduction in dead discards of gag. However, due to the... percent to account for additional dead discards not accounted for in the assessment analyses. Therefore... gag regulatory dead discards is to reduce the commercial minimum size limit so that gag that would...

78 FR 15672 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Snapper-Grouper Fishery Off the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... projected commercial and/or recreational fishing seasons are determined by NMFS to be 3 days or [[Page 15674... length (TL), minimum size limit for both the commercial and recreational sectors to decrease regulatory... Fisheries Service. [FR Doc. 2013-05644 Filed 3-11-13; 8:45 am] BILLING CODE 3510-22-P ...

7 CFR 51.1216 - Size requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) The numerical count or a count-size based on equivalent tray pack size designations or the minimum... numerical count is not shown the minimum diameter shall be plainly stamped, stenciled, or otherwise marked...

7 CFR 51.1216 - Size requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) The numerical count or a count-size based on equivalent tray pack size designations or the minimum... numerical count is not shown the minimum diameter shall be plainly stamped, stenciled, or otherwise marked...

Practical implementation of channelized hotelling observers: effect of ROI size

NASA Astrophysics Data System (ADS)

Ferrero, Andrea; Favazza, Christopher P.; Yu, Lifeng; Leng, Shuai; McCollough, Cynthia H.

2017-03-01

Fundamental to the development and application of channelized Hotelling observer (CHO) models is the selection of the region of interest (ROI) to evaluate. For assessment of medical imaging systems, reducing the ROI size can be advantageous. Smaller ROIs enable a greater concentration of interrogable objects in a single phantom image, thereby providing more information from a set of images and reducing the overall image acquisition burden. Additionally, smaller ROIs may promote better assessment of clinical patient images as different patient anatomies present different ROI constraints. To this end, we investigated the minimum ROI size that does not compromise the performance of the CHO model. In this study, we evaluated both simulated images and phantom CT images to identify the minimum ROI size that resulted in an accurate figure of merit (FOM) of the CHO's performance. More specifically, the minimum ROI size was evaluated as a function of the following: number of channels, spatial frequency and number of rotations of the Gabor filters, size and contrast of the object, and magnitude of the image noise. Results demonstrate that a minimum ROI size exists below which the CHO's performance is grossly inaccurate. The minimum ROI size is shown to increase with number of channels and be dictated by truncation of lower frequency filters. We developed a model to estimate the minimum ROI size as a parameterized function of the number of orientations and spatial frequencies of the Gabor filters, providing a guide for investigators to appropriately select parameters for model observer studies.

Practical implementation of Channelized Hotelling Observers: Effect of ROI size.

PubMed

Ferrero, Andrea; Favazza, Christopher P; Yu, Lifeng; Leng, Shuai; McCollough, Cynthia H

2017-03-01

Fundamental to the development and application of channelized Hotelling observer (CHO) models is the selection of the region of interest (ROI) to evaluate. For assessment of medical imaging systems, reducing the ROI size can be advantageous. Smaller ROIs enable a greater concentration of interrogable objects in a single phantom image, thereby providing more information from a set of images and reducing the overall image acquisition burden. Additionally, smaller ROIs may promote better assessment of clinical patient images as different patient anatomies present different ROI constraints. To this end, we investigated the minimum ROI size that does not compromise the performance of the CHO model. In this study, we evaluated both simulated images and phantom CT images to identify the minimum ROI size that resulted in an accurate figure of merit (FOM) of the CHO's performance. More specifically, the minimum ROI size was evaluated as a function of the following: number of channels, spatial frequency and number of rotations of the Gabor filters, size and contrast of the object, and magnitude of the image noise. Results demonstrate that a minimum ROI size exists below which the CHO's performance is grossly inaccurate. The minimum ROI size is shown to increase with number of channels and be dictated by truncation of lower frequency filters. We developed a model to estimate the minimum ROI size as a parameterized function of the number of orientations and spatial frequencies of the Gabor filters, providing a guide for investigators to appropriately select parameters for model observer studies.

Annual plants change in size over a century of observations.

PubMed

Leger, Elizabeth A

2013-07-01

Studies have documented changes in animal body sizes over the last century, but very little is known about changes in plant sizes, even though reduced plant productivity is potentially responsible for declines in size of other organisms. Here, I ask whether warming trends in the Great Basin have affected plant size by measuring specimens preserved on herbarium sheets collected between 1893 and 2011. I asked how maximum and minimum temperatures, precipitation, and the Pacific Decadal Oscillation (PDO) in the year of collection affected plant height, leaf size, and flower number, and asked whether changes in climate resulted in decreasing sizes for seven annual forbs. Species had contrasting responses to climate factors, and would not necessarily be expected to respond in parallel to climatic shifts. There were generally positive relationships between plant size and increased minimum and maximum temperatures, which would have been predicted to lead to small increases in plant sizes over the observation period. While one species increased in size and flower number over the observation period, five of the seven species decreased in plant height, four of these decreased in leaf size, and one species also decreased in flower production. One species showed no change. The mechanisms behind these size changes are unknown, and the limited data available on these species (germination timing, area of occupancy, relative abundance) did not explain why some species shrank while others grew or did not change in size over time. These results show that multiple annual forbs are decreasing in size, but that even within the same functional group, species may have contrasting responses to similar environmental stimuli. Changes in plant size could have cascading effects on other members of these communities, and differential responses to directional change may change the composition of plant communities over time. © 2013 Blackwell Publishing Ltd.

24 CFR 984.105 - Minimum program size.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVELOPMENT SECTION 8 AND PUBLIC HOUSING FAMILY SELF-SUFFICIENCY PROGRAM General § 984.105 Minimum program... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Minimum program size. 984.105 Section 984.105 Housing and Urban Development Regulations Relating to Housing and Urban Development...

Functionality limit of classical simulated annealing

NASA Astrophysics Data System (ADS)

Hasegawa, M.

2015-09-01

By analyzing the system dynamics in the landscape paradigm, optimization function of classical simulated annealing is reviewed on the random traveling salesman problems. The properly functioning region of the algorithm is experimentally determined in the size-time plane and the influence of its boundary on the scalability test is examined in the standard framework of this method. From both results, an empirical choice of temperature length is plausibly explained as a minimum requirement that the algorithm maintains its scalability within its functionality limit. The study exemplifies the applicability of computational physics analysis to the optimization algorithm research.

Practical implementation of Channelized Hotelling Observers: Effect of ROI size

PubMed Central

Yu, Lifeng; Leng, Shuai; McCollough, Cynthia H.

2017-01-01

Fundamental to the development and application of channelized Hotelling observer (CHO) models is the selection of the region of interest (ROI) to evaluate. For assessment of medical imaging systems, reducing the ROI size can be advantageous. Smaller ROIs enable a greater concentration of interrogable objects in a single phantom image, thereby providing more information from a set of images and reducing the overall image acquisition burden. Additionally, smaller ROIs may promote better assessment of clinical patient images as different patient anatomies present different ROI constraints. To this end, we investigated the minimum ROI size that does not compromise the performance of the CHO model. In this study, we evaluated both simulated images and phantom CT images to identify the minimum ROI size that resulted in an accurate figure of merit (FOM) of the CHO’s performance. More specifically, the minimum ROI size was evaluated as a function of the following: number of channels, spatial frequency and number of rotations of the Gabor filters, size and contrast of the object, and magnitude of the image noise. Results demonstrate that a minimum ROI size exists below which the CHO’s performance is grossly inaccurate. The minimum ROI size is shown to increase with number of channels and be dictated by truncation of lower frequency filters. We developed a model to estimate the minimum ROI size as a parameterized function of the number of orientations and spatial frequencies of the Gabor filters, providing a guide for investigators to appropriately select parameters for model observer studies. PMID:28943699

Design of digital voice storage and playback system

NASA Astrophysics Data System (ADS)

Tang, Chao

2018-03-01

Based on STC89C52 chip, this paper presents a single chip microcomputer minimum system, which is used to realize the logic control of digital speech storage and playback system. Compared with the traditional tape voice recording system, the system has advantages of small size, low power consumption, The effective solution of traditional voice recording system is limited in the use of electronic and information processing.

HYPERSAMP - HYPERGEOMETRIC ATTRIBUTE SAMPLING SYSTEM BASED ON RISK AND FRACTION DEFECTIVE

NASA Technical Reports Server (NTRS)

De, Salvo L. J.

1994-01-01

HYPERSAMP is a demonstration of an attribute sampling system developed to determine the minimum sample size required for any preselected value for consumer's risk and fraction of nonconforming. This statistical method can be used in place of MIL-STD-105E sampling plans when a minimum sample size is desirable, such as when tests are destructive or expensive. HYPERSAMP utilizes the Hypergeometric Distribution and can be used for any fraction nonconforming. The program employs an iterative technique that circumvents the obstacle presented by the factorial of a non-whole number. HYPERSAMP provides the required Hypergeometric sample size for any equivalent real number of nonconformances in the lot or batch under evaluation. Many currently used sampling systems, such as the MIL-STD-105E, utilize the Binomial or the Poisson equations as an estimate of the Hypergeometric when performing inspection by attributes. However, this is primarily because of the difficulty in calculation of the factorials required by the Hypergeometric. Sampling plans based on the Binomial or Poisson equations will result in the maximum sample size possible with the Hypergeometric. The difference in the sample sizes between the Poisson or Binomial and the Hypergeometric can be significant. For example, a lot size of 400 devices with an error rate of 1.0% and a confidence of 99% would require a sample size of 400 (all units would need to be inspected) for the Binomial sampling plan and only 273 for a Hypergeometric sampling plan. The Hypergeometric results in a savings of 127 units, a significant reduction in the required sample size. HYPERSAMP is a demonstration program and is limited to sampling plans with zero defectives in the sample (acceptance number of zero). Since it is only a demonstration program, the sample size determination is limited to sample sizes of 1500 or less. The Hypergeometric Attribute Sampling System demonstration code is a spreadsheet program written for IBM PC compatible computers running DOS and Lotus 1-2-3 or Quattro Pro. This program is distributed on a 5.25 inch 360K MS-DOS format diskette, and the program price includes documentation. This statistical method was developed in 1992.

A Methodology to Assess the Capability of Engine Designs to Meet Closed-Loop Performance and Operability Requirements

NASA Technical Reports Server (NTRS)

Zinnecker, Alicia M.; Csank, Jeffrey

2015-01-01

Designing a closed-loop controller for an engine requires balancing trade-offs between performance and operability of the system. One such trade-off is the relationship between the 95 percent response time and minimum high-pressure compressor (HPC) surge margin (SM) attained during acceleration from idle to takeoff power. Assuming a controller has been designed to meet some specification on response time and minimum HPC SM for a mid-life (nominal) engine, there is no guarantee that these limits will not be violated as the engine ages, particularly as it reaches the end of its life. A characterization for the uncertainty in this closed-loop system due to aging is proposed that defines elliptical boundaries to estimate worst-case performance levels for a given control design point. The results of this characterization can be used to identify limiting design points that bound the possible controller designs yielding transient results that do not exceed specified limits in response time or minimum HPC SM. This characterization involves performing Monte Carlo simulation of the closed-loop system with controller constructed for a set of trial design points and developing curve fits to describe the size and orientation of each ellipse; a binary search procedure is then employed that uses these fits to identify the limiting design point. The method is demonstrated through application to a generic turbofan engine model in closed-loop with a simplified controller; it is found that the limit for which each controller was designed was exceeded by less than 4.76 percent. Extension of the characterization to another trade-off, that between the maximum high-pressure turbine (HPT) entrance temperature and minimum HPC SM, showed even better results: the maximum HPT temperature was estimated within 0.76 percent. Because of the accuracy in this estimation, this suggests another limit that may be taken into consideration during design and analysis. It also demonstrates the extension of the characterization to other attributes that contribute to the performance or operability of the engine. Metrics are proposed that, together, provide information on the shape of the trade-off between response time and minimum HPC SM, and how much each varies throughout the life cycle, at the limiting design points. These metrics also facilitate comparison of the expected transient behavior for multiple engine models.

A Methodology to Assess the Capability of Engine Designs to Meet Closed-loop Performance and Operability Requirements

NASA Technical Reports Server (NTRS)

Zinnecker, Alicia M.; Csank, Jeffrey T.

2015-01-01

Designing a closed-loop controller for an engine requires balancing trade-offs between performance and operability of the system. One such trade-off is the relationship between the 95% response time and minimum high-pressure compressor (HPC) surge margin (SM) attained during acceleration from idle to takeoff power. Assuming a controller has been designed to meet some specification on response time and minimum HPC SM for a mid-life (nominal) engine, there is no guarantee that these limits will not be violated as the engine ages, particularly as it reaches the end of its life. A characterization for the uncertainty in this closed-loop system due to aging is proposed that defines elliptical boundaries to estimate worst-case performance levels for a given control design point. The results of this characterization can be used to identify limiting design points that bound the possible con- troller designs yielding transient results that do not exceed specified limits in response time or minimum HPC SM. This characterization involves performing Monte Carlo simulation of the closed-loop system with controller constructed for a set of trial design points and developing curve fits to describe the size and orientation of each ellipse; a binary search procedure is then employed that uses these fits to identify the limiting design point. The method is demonstrated through application to a generic turbofan engine model in closed- loop with a simplified controller; it is found that the limit for which each controller was designed was exceeded by less than 4.76%. Extension of the characterization to another trade-off, that between the maximum high-pressure turbine (HPT) entrance temperature and minimum HPC SM, showed even better results: the maximum HPT temperature was estimated within 0.76%. Because of the accuracy in this estimation, this suggests another limit that may be taken into consideration during design and analysis. It also demonstrates the extension of the characterization to other attributes that contribute to the performance or operability of the engine. Metrics are proposed that, together, provide information on the shape of the trade-off between response time and minimum HPC SM, and how much each varies throughout the life cycle, at the limiting design points. These metrics also facilitate comparison of the expected transient behavior for multiple engine models.

On the Importance of Cycle Minimum in Sunspot Cycle Prediction

NASA Technical Reports Server (NTRS)

Wilson, Robert M.; Hathaway, David H.; Reichmann, Edwin J.

1996-01-01

The characteristics of the minima between sunspot cycles are found to provide important information for predicting the amplitude and timing of the following cycle. For example, the time of the occurrence of sunspot minimum sets the length of the previous cycle, which is correlated by the amplitude-period effect to the amplitude of the next cycle, with cycles of shorter (longer) than average length usually being followed by cycles of larger (smaller) than average size (true for 16 of 21 sunspot cycles). Likewise, the size of the minimum at cycle onset is correlated with the size of the cycle's maximum amplitude, with cycles of larger (smaller) than average size minima usually being associated with larger (smaller) than average size maxima (true for 16 of 22 sunspot cycles). Also, it was found that the size of the previous cycle's minimum and maximum relates to the size of the following cycle's minimum and maximum with an even-odd cycle number dependency. The latter effect suggests that cycle 23 will have a minimum and maximum amplitude probably larger than average in size (in particular, minimum smoothed sunspot number Rm = 12.3 +/- 7.5 and maximum smoothed sunspot number RM = 198.8 +/- 36.5, at the 95-percent level of confidence), further suggesting (by the Waldmeier effect) that it will have a faster than average rise to maximum (fast-rising cycles have ascent durations of about 41 +/- 7 months). Thus, if, as expected, onset for cycle 23 will be December 1996 +/- 3 months, based on smoothed sunspot number, then the length of cycle 22 will be about 123 +/- 3 months, inferring that it is a short-period cycle and that cycle 23 maximum amplitude probably will be larger than average in size (from the amplitude-period effect), having an RM of about 133 +/- 39 (based on the usual +/- 30 percent spread that has been seen between observed and predicted values), with maximum amplitude occurrence likely sometime between July 1999 and October 2000.

Human Factors Assessment of Vibration Effects on Visual Performance During Launch

NASA Technical Reports Server (NTRS)

Holden, Kritina

2009-01-01

The Human Factors Assessment of Vibration Effects on Visual Performance During Launch (Visual Performance) investigation will determine visual performance limits during operational vibration and g-loads on the Space Shuttle, specifically through the determination of minimum readable font size during ascent using planned Orion display formats. Research Summary: The aim of the Human Factors Assessment of Vibration Effects on Visual Performance during Launch (Visual Performance) investigation is to provide supplementary data to that collected by the Thrust Oscillation Seat Detailed Technical Objective (DTO) 695 (Crew Seat DTO) which will measure seat acceleration and vibration from one flight deck and two middeck seats during ascent. While the Crew Seat DTO data alone are important in terms of providing a measure of vibration and g-loading, human performance data are required to fully interpret the operational consequences of the vibration values collected during Space Shuttle ascent. During launch, crewmembers will be requested to view placards with varying font sizes and indicate the minimum readable size. In combination with the Crew Seat DTO, the Visual Performance investigation will: Provide flight-validated evidence that will be used to establish vibration limits for visual performance during combined vibration and linear g-loading. o Provide flight data as inputs to ongoing ground-based simulations, which will further validate crew visual performance under vibration loading in a controlled environment. o Provide vibration and performance metrics to help validate procedures for ground tests and analyses of seats, suits, displays and controls, and human-in-the-loop performance.

Impacts of coronary artery eccentricity on macro-recirculation and pressure drops using computational fluid dynamics

NASA Astrophysics Data System (ADS)

Poon, Eric; Thondapu, Vikas; Barlis, Peter; Ooi, Andrew

2017-11-01

Coronary artery disease remains a major cause of mortality in developed countries, and is most often due to a localized flow-limiting stenosis, or narrowing, of coronary arteries. Patients often undergo invasive procedures such as X-ray angiography and fractional flow reserve to diagnose flow-limiting lesions. Even though such diagnostic techniques are well-developed, the effects of diseased coronary segments on local flow are still poorly understood. Therefore, this study investigated the effect of irregular geometries of diseased coronary segments on the macro-recirculation and local pressure minimum regions. We employed an idealized coronary artery model with a diameter of stenosis of 75%. By systematically adjusting the eccentricity and the asymmetry of the coronary stenosis, we uncovered an increase in macro-recirculation size. Most importantly, the presence of this macro-recirculation signifies a local pressure minimum (identified by λ2 vortex identification method). This local pressure minimum has a profound effect on the pressure drops in both longitudinal and planar directions, which has implications for diagnosis and treatment of coronary artery disease. Supported by Australian Research Council LP150100233 and National Computational Infrastructure m45.

Dry etching of chrome for photomasks for 100-nm technology using chemically amplified resist

NASA Astrophysics Data System (ADS)

Mueller, Mark; Komarov, Serguie; Baik, Ki-Ho

2002-07-01

Photo mask etching for the 100nm technology node places new requirements on dry etching processes. As the minimum-size features on the mask, such as assist bars and optical proximity correction (OPC) patterns, shrink down to 100nm, it is necessary to produce etch CD biases of below 20nm in order to reproduce minimum resist features into chrome with good pattern fidelity. In addition, vertical profiles are necessary. In previous generations of photomask technology, footing and sidewall profile slope were tolerated, since this dry etch profile was an improvement from wet etching. However, as feature sizes shrink, it is extremely important to select etch processes which do not generate a foot, because this will affect etch linearity and also limit the smallest etched feature size. Chemically amplified resist (CAR) from TOK is patterned with a 50keV MEBES eXara e-beam writer, allowing for patterning of small features with vertical resist profiles. This resist is developed for raster scan 50 kV e-beam systems. It has high contrast, good coating characteristics, good dry etch selectivity, and high environmental stability. Chrome etch process development has been performed using Design of Experiments to optimize parameters such as sidewall profile, etch CD bias, etch CD linearity for varying sizes of line/space patterns, etch CD linearity for varying sizes of isolated lines and spaces, loading effects, and application to contact etching.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, M; Beltran, C; Herman, M

Purpose: To investigate the influence of the minimum monitor unit (MU) on the quality of clinical treatment plans for scanned proton therapy. Methods: Delivery system characteristics limit the minimum number of protons that can be delivered per spot, resulting in a min-MU limit. Plan quality can be impacted by the min-MU limit. Two sites were used to investigate the impact of min-MU on treatment plans: pediatric brain tumor at a depth of 5-10 cm; a head and neck tumor at a depth of 1-20 cm. Three field intensity modulated spot scanning proton plans were created for each site with themore » following parameter variations: min-MU limit range of 0.0000-0.0060; and spot spacing range of 0.5-2.0σ of the nominal spot size at isocenter in water (σ=4mm in this work). Comparisons were based on target homogeneity and normal tissue sparing. Results: The increase of the min-MU with a fixed spot spacing decreases plan quality both in homogeneous target coverage and in the avoidance of critical structures. Both head and neck and pediatric brain plans show a 20% increase in relative dose for the hot spot in the CTV and 10% increase in key critical structures when comparing min-MU limits of 0.0000 and 0.0060 with a fixed spot spacing of 1σ. The DVHs of CTVs show min-MU limits of 0.0000 and 0.0010 produce similar plan quality and quality decreases as the min-MU limit increases beyond 0.0020. As spot spacing approaches 2σ, degradation in plan quality is observed when no min-MU limit is imposed. Conclusion: Given a fixed spot spacing of ≤ 1σ of the spot size in water, plan quality decreases as min- MU increases greater than 0.0020. The effect of min-MU should be taken into consideration while planning spot scanning proton therapy treatments to realize its full potential.« less

Interspecific geographic range size-body size relationship and the diversification dynamics of Neotropical furnariid birds.

PubMed

Inostroza-Michael, Oscar; Hernández, Cristián E; Rodríguez-Serrano, Enrique; Avaria-Llautureo, Jorge; Rivadeneira, Marcelo M

2018-05-01

Among the earliest macroecological patterns documented, is the range and body size relationship, characterized by a minimum geographic range size imposed by the species' body size. This boundary for the geographic range size increases linearly with body size and has been proposed to have implications in lineages evolution and conservation. Nevertheless, the macroevolutionary processes involved in the origin of this boundary and its consequences on lineage diversification have been poorly explored. We evaluate the macroevolutionary consequences of the difference (hereafter the distance) between the observed and the minimum range sizes required by the species' body size, to untangle its role on the diversification of a Neotropical species-rich bird clade using trait-dependent diversification models. We show that speciation rate is a positive hump-shaped function of the distance to the lower boundary. The species with highest and lowest distances to minimum range size had lower speciation rates, while species close to medium distances values had the highest speciation rates. Further, our results suggest that the distance to the minimum range size is a macroevolutionary constraint that affects the diversification process responsible for the origin of this macroecological pattern in a more complex way than previously envisioned. © 2018 The Author(s). Evolution © 2018 The Society for the Study of Evolution.

Magnetic Properties of Nanoparticle Matrix Composites

DTIC Science & Technology

2015-06-02

recording materials with large value of Ku are SmCo5 with Ku = 11-20 x 10 7 erg/cm 3 for the minimum stable particle size of 2.45 nm, FePt with Ku...nanoparticles and the matrix compared with the bulk behavior of the soft and hard phases and ferromagnetic coupling. 15. SUBJECT TERMS...Magnetic materials , Ab initio methods, nanoparticles, Nanocomposites, Ferromagnetics 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT

Management implications of long-term tree growth and mortality rates: A modeling study of big-leaf mahogany (Swietenia macrophylla) in the Brazilian Amazon

Treesearch

C.M. Free; R.M. Landis; J. Grogan; M.D. Schulze; M. Lentini; O. Dunisch; NO-VALUE

2014-01-01

Knowledge of tree age-size relationships is essential towards evaluating the sustainability of harvest regulations that include minimum diameter cutting limits and fixed-length cutting cycles. Although many tropical trees form annual growth rings and can be aged from discs or cores, destructive sampling is not always an option for valuable or threatened species. We...

Minimum size limits for yellow perch (Perca flavescens) in western Lake Erie

USGS Publications Warehouse

Hartman, Wilbur L.; Nepszy, Stephen J.; Scholl, Russell L.

1980-01-01

During the 1960's yellow perch (Perca flavescens) of Lake Erie supported a commercial fishery that produced an average annual catch of 23 million pounds, as well as a modest sport fishery. Since 1969, the resource has seriously deteriorated. Commercial landings amounted to only 6 million pounds in 1976, and included proportionally more immature perch than in the 1960's. Moreover, no strong year classes were produced between 1965 and 1975. An interagency technical committee was appointed in 1975 by the Lake Erie Committee of the Great Lakes Fishery Commission to develop an interim management strategy that would provide for greater protection of perch in western Lake Erie, where declines have been the most severe. The committee first determined the age structure, growth and mortality rates, maturation schedule, and length-fecundity relationship for the population, and then applied Ricker-type equilibrium yield models to determine the effects of various minimum length limits on yield, production, average stock weight, potential egg deposition, and the Abrosov spawning frequency indicator (average number of spawning opportunities per female). The committee recommended increasing the minimum length limit of 5.0 inches to at least 8.5 inches. Theoretically, this change would increase the average stock weight by 36% and potential egg deposition by 44%, without significantly decreasing yield. Abrosov's spawning frequency indicator would rise from the existing 0.6 to about 1.2.

Population limitation in a non-cyclic arctic fox population in a changing climate.

PubMed

Pálsson, Snæbjörn; Hersteinsson, Páll; Unnsteinsdóttir, Ester R; Nielsen, Ólafur K

2016-04-01

Arctic foxes Vulpes lagopus (L.) display a sharp 3- to 5-year fluctuation in population size where lemmings are their main prey. In areas devoid of lemmings, such as Iceland, they do not experience short-term fluctuations. This study focusses on the population dynamics of the arctic fox in Iceland and how it is shaped by its main prey populations. Hunting statistics from 1958-2003 show that the population size of the arctic fox was at a maximum in the 1950s, declined to a minimum in the 1970s, and increased steadily until 2003. Analysis of the arctic fox population size and their prey populations suggests that fox numbers were limited by rock ptarmigan numbers during the decline period. The recovery of the arctic fox population was traced mostly to an increase in goose populations, and favourable climatic conditions as reflected by the Subpolar Gyre. These results underscore the flexibility of a generalist predator and its responses to shifting food resources and climate changes.

Energetic tradeoffs control the size distribution of aquatic mammals

NASA Astrophysics Data System (ADS)

Gearty, William; McClain, Craig R.; Payne, Jonathan L.

2018-04-01

Four extant lineages of mammals have invaded and diversified in the water: Sirenia, Cetacea, Pinnipedia, and Lutrinae. Most of these aquatic clades are larger bodied, on average, than their closest land-dwelling relatives, but the extent to which potential ecological, biomechanical, and physiological controls contributed to this pattern remains untested quantitatively. Here, we use previously published data on the body masses of 3,859 living and 2,999 fossil mammal species to examine the evolutionary trajectories of body size in aquatic mammals through both comparative phylogenetic analysis and examination of the fossil record. Both methods indicate that the evolution of an aquatic lifestyle is driving three of the four extant aquatic mammal clades toward a size attractor at ˜500 kg. The existence of this body size attractor and the relatively rapid selection toward, and limited deviation from, this attractor rule out most hypothesized drivers of size increase. These three independent body size increases and a shared aquatic optimum size are consistent with control by differences in the scaling of energetic intake and cost functions with body size between the terrestrial and aquatic realms. Under this energetic model, thermoregulatory costs constrain minimum size, whereas limitations on feeding efficiency constrain maximum size. The optimum size occurs at an intermediate value where thermoregulatory costs are low but feeding efficiency remains high. Rather than being released from size pressures, water-dwelling mammals are driven and confined to larger body sizes by the strict energetic demands of the aquatic medium.

On size-constrained minimum s–t cut problems and size-constrained dense subgraph problems

DOE PAGES

Chen, Wenbin; Samatova, Nagiza F.; Stallmann, Matthias F.; ...

2015-10-30

In some application cases, the solutions of combinatorial optimization problems on graphs should satisfy an additional vertex size constraint. In this paper, we consider size-constrained minimum s–t cut problems and size-constrained dense subgraph problems. We introduce the minimum s–t cut with at-least-k vertices problem, the minimum s–t cut with at-most-k vertices problem, and the minimum s–t cut with exactly k vertices problem. We prove that they are NP-complete. Thus, they are not polynomially solvable unless P = NP. On the other hand, we also study the densest at-least-k-subgraph problem (DalkS) and the densest at-most-k-subgraph problem (DamkS) introduced by Andersen andmore » Chellapilla [1]. We present a polynomial time algorithm for DalkS when k is bounded by some constant c. We also present two approximation algorithms for DamkS. In conclusion, the first approximation algorithm for DamkS has an approximation ratio of n-1/k-1, where n is the number of vertices in the input graph. The second approximation algorithm for DamkS has an approximation ratio of O (n δ), for some δ < 1/3.« less

[Problems of implementing integration management at company level in small and medium-sized enterprises].

PubMed

Hetzel, C; Flach, T; Weber, A; Schian, H-M

2006-05-01

At company level responsibility increases for the employment of workers with health-related problems or disabilities, but realisation in small and medium-sized enterprises (SME) is lacking. Therefore a model is developed based on theory and a survey. Minimum requirements for "betriebliches Eingliederungsmanagement" (integration management at company level) according to section 84 (2) SGB IX Book 9 of the German Social Code, the main products of the international movement "disability management", a description of roles for realisation and the main sources of employers' support are described. Although external supporting of SMEs is unquestioned, it is expensive and retards own initiative and own activity counting solely on this. Only by developing a minimum of SME's awareness, acceptance and competence, this will open up to (currently suboptimal) external support. Goal is identifying SME managers' attitudes, activities, proposals and expectations referring integration management at company level to derive concepts of SME's support. 13 interviews are analysed by qualitative content analysis identifying the following barriers: information deficit, absence of priority, limited possibilities for transitional work, cost, partially limited workers' self-responsibility, illness as a "tabes" subject. Possibilities overcoming these barriers are delineated. On that basis a model is presented: pragmatically for realisation, a company contact person with minimum competence, uniform external support, institutional partners' integration and quality assurance according to disability management. Interlocking SME world and social insurance world means first to support SME's awareness, acceptance and competence, second to create for SME a central contact in the "rehabilitation jungle" and third to develop SME-suitable premiums according to section 84 (3) SGB IX, Book 9 of the German social code.

Spatial analyses for nonoverlapping objects with size variations and their application to coral communities.

PubMed

Muko, Soyoka; Shimatani, Ichiro K; Nozawa, Yoko

2014-07-01

Spatial distributions of individuals are conventionally analysed by representing objects as dimensionless points, in which spatial statistics are based on centre-to-centre distances. However, if organisms expand without overlapping and show size variations, such as is the case for encrusting corals, interobject spacing is crucial for spatial associations where interactions occur. We introduced new pairwise statistics using minimum distances between objects and demonstrated their utility when examining encrusting coral community data. We also calculated the conventional point process statistics and the grid-based statistics to clarify the advantages and limitations of each spatial statistical method. For simplicity, coral colonies were approximated by disks in these demonstrations. Focusing on short-distance effects, the use of minimum distances revealed that almost all coral genera were aggregated at a scale of 1-25 cm. However, when fragmented colonies (ramets) were treated as a genet, a genet-level analysis indicated weak or no aggregation, suggesting that most corals were randomly distributed and that fragmentation was the primary cause of colony aggregations. In contrast, point process statistics showed larger aggregation scales, presumably because centre-to-centre distances included both intercolony spacing and colony sizes (radius). The grid-based statistics were able to quantify the patch (aggregation) scale of colonies, but the scale was strongly affected by the colony size. Our approach quantitatively showed repulsive effects between an aggressive genus and a competitively weak genus, while the grid-based statistics (covariance function) also showed repulsion although the spatial scale indicated from the statistics was not directly interpretable in terms of ecological meaning. The use of minimum distances together with previously proposed spatial statistics helped us to extend our understanding of the spatial patterns of nonoverlapping objects that vary in size and the associated specific scales. © 2013 The Authors. Journal of Animal Ecology © 2013 British Ecological Society.

A feasibility study in adapting Shamos Bickel and Hodges Lehman estimator into T-Method for normalization

NASA Astrophysics Data System (ADS)

Harudin, N.; Jamaludin, K. R.; Muhtazaruddin, M. Nabil; Ramlie, F.; Muhamad, Wan Zuki Azman Wan

2018-03-01

T-Method is one of the techniques governed under Mahalanobis Taguchi System that developed specifically for multivariate data predictions. Prediction using T-Method is always possible even with very limited sample size. The user of T-Method required to clearly understanding the population data trend since this method is not considering the effect of outliers within it. Outliers may cause apparent non-normality and the entire classical methods breakdown. There exist robust parameter estimate that provide satisfactory results when the data contain outliers, as well as when the data are free of them. The robust parameter estimates of location and scale measure called Shamos Bickel (SB) and Hodges Lehman (HL) which are used as a comparable method to calculate the mean and standard deviation of classical statistic is part of it. Embedding these into T-Method normalize stage feasibly help in enhancing the accuracy of the T-Method as well as analysing the robustness of T-method itself. However, the result of higher sample size case study shows that T-method is having lowest average error percentages (3.09%) on data with extreme outliers. HL and SB is having lowest error percentages (4.67%) for data without extreme outliers with minimum error differences compared to T-Method. The error percentages prediction trend is vice versa for lower sample size case study. The result shows that with minimum sample size, which outliers always be at low risk, T-Method is much better on that, while higher sample size with extreme outliers, T-Method as well show better prediction compared to others. For the case studies conducted in this research, it shows that normalization of T-Method is showing satisfactory results and it is not feasible to adapt HL and SB or normal mean and standard deviation into it since it’s only provide minimum effect of percentages errors. Normalization using T-method is still considered having lower risk towards outlier’s effect.

The demographic consequences of growing older and bigger in oyster populations.

PubMed

Moore, Jacob L; Lipcius, Romuald N; Puckett, Brandon; Schreiber, Sebastian J

2016-10-01

Structured population models, particularly size- or age-structured, have a long history of informing conservation and natural resource management. While size is often easier to measure than age and is the focus of many management strategies, age-structure can have important effects on population dynamics that are not captured in size-only models. However, relatively few studies have included the simultaneous effects of both age- and size-structure. To better understand how population structure, particularly that of age and size, impacts restoration and management decisions, we developed and compared a size-structured integral projection model (IPM) and an age- and size-structured IPM, using a population of Crassostrea gigas oysters in the northeastern Pacific Ocean. We analyzed sensitivity of model results across values of local retention that give populations decreasing in size to populations increasing in size. We found that age- and size-structured models yielded the best fit to the demographic data and provided more reliable results about long-term demography. Elasticity analysis showed that population growth rate was most sensitive to changes in the survival of both large (>175 mm shell length) and small (<75 mm shell length) oysters, indicating that a maximum size limit, in addition to a minimum size limit, could be an effective strategy for maintaining a sustainable population. In contrast, the purely size-structured model did not detect the importance of large individuals. Finally, patterns in stable age and stable size distributions differed between populations decreasing in size due to limited local retention and populations increasing in size due to high local retention. These patterns can be used to determine population status and restoration success. The methodology described here provides general insight into the necessity of including both age- and size-structure into modeling frameworks when using population models to inform restoration and management decisions. © 2016 by the Ecological Society of America.

Spark Ignition of Monodisperse Fuel Sprays. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Danis, Allen M.; Cernansky, Nicholas P.; Namer, Izak

1987-01-01

A study of spark ignition energy requirements was conducted with a monodisperse spray system allowing independent control of droplet size, equivalent ratio, and fuel type. Minimum ignition energies were measured for n-heptane and methanol sprays characterized at the spark gap in terms of droplet diameter, equivalence ratio (number density) and extent of prevaporization. In addition to sprays, minimum ignition energies were measured for completely prevaporized mixtures of the same fuels over a range of equivalence ratios to provide data at the lower limit of droplet size. Results showed that spray ignition was enhanced with decreasing droplet size and increasing equivalence ratio over the ranges of the parameters studied. By comparing spray and prevaporized ignition results, the existence of an optimum droplet size for ignition was indicated for both fuels. Fuel volatility was seen to be a critical factor in spray ignition. The spray ignition results were analyzed using two different empirical ignition models for quiescent mixtures. Both models accurately predicted the experimental ignition energies for the majority of the spray conditions. Spray ignition was observed to be probabilistic in nature, and ignition was quantified in terms of an ignition frequency for a given spark energy. A model was developed to predict ignition frequencies based on the variation in spark energy and equivalence ratio in the spark gap. The resulting ignition frequency simulations were nearly identical to the experimentally observed values.

Simulating the minimum core for hydrophobic collapse in globular proteins.

PubMed Central

Tsai, J.; Gerstein, M.; Levitt, M.

1997-01-01

To investigate the nature of hydrophobic collapse considered to be the driving force in protein folding, we have simulated aqueous solutions of two model hydrophobic solutes, methane and isobutylene. Using a novel methodology for determining contacts, we can precisely follow hydrophobic aggregation as it proceeds through three stages: dispersed, transition, and collapsed. Theoretical modeling of the cluster formation observed by simulation indicates that this aggregation is cooperative and that the simulations favor the formation of a single cluster midway through the transition stage. This defines a minimum solute hydrophobic core volume. We compare this with protein hydrophobic core volumes determined from solved crystal structures. Our analysis shows that the solute core volume roughly estimates the minimum core size required for independent hydrophobic stabilization of a protein and defines a limiting concentration of nonpolar residues that can cause hydrophobic collapse. These results suggest that the physical forces driving aggregation of hydrophobic molecules in water is indeed responsible for protein folding. PMID:9416609

Estimation of homogeneous nucleation flux via a kinetic model

NASA Technical Reports Server (NTRS)

Wilcox, C. F.; Bauer, S. H.

1991-01-01

The proposed kinetic model for condensation under homogeneous conditions, and the onset of unidirectional cluster growth in supersaturated gases, does not suffer from the conceptual flaws that characterize classical nucleation theory. When a full set of simultaneous rate equation is solved, a characteristic time emerges, for each cluster size, at which the production rate, and its rate of conversion to the next size (n + 1) are equal. Procedures for estimating the essential parameters are proposed; condensation fluxes J(kin) exp ss are evaluated. Since there are practical limits to the cluster size that can be incorporated in the set of simultaneous first-order differential equations, a code was developed for computing an approximate J(th) exp ss based on estimates of a 'constrained equilibrium' distribution, and identification of its minimum.

Effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter

NASA Technical Reports Server (NTRS)

Ko, William L.; Olona, Timothy

1987-01-01

The effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter was investigated. Several structural performance and resizing (SPAR) thermal models and NASA structural analysis (NASTRAN) structural models were set up for the orbiter wing midspan bay 3. The thermal model was found to be the one that determines the limit of finite-element fineness because of the limitation of computational core space required for the radiation view factor calculations. The thermal stresses were found to be extremely sensitive to a slight variation of structural temperature distributions. The minimum degree of element fineness required for the thermal model to yield reasonably accurate solutions was established. The radiation view factor computation time was found to be insignificant compared with the total computer time required for the SPAR transient heat transfer analysis.

Colorado River sediment transport: 2. Systematic bed‐elevation and grain‐size effects of sand supply limitation

USGS Publications Warehouse

Topping, David J.; Rubin, David M.; Nelson, Jonathan M.; Kinzel, Paul J.; Corson, Ingrid C.

2000-01-01

The Colorado River in Marble and Grand Canyons displays evidence of annual supply limitation with respect to sand both prior to [Topping et al, this issue] and after the closure of Glen Canyon Dam in 1963. Systematic changes in bed elevation and systematic coupled changes in suspended‐sand concentration and grain size result from this supply limitation. During floods, sand supply limitation either causes or modifies a lag between the time of maximum discharge and the time of either maximum or minimum (depending on reach geometry) bed elevation. If, at a cross section where the bed aggrades with increasing flow, the maximum bed elevation is observed to lead the peak or the receding limb of a flood, then this observed response of the bed is due to sand supply limitation. Sand supply limitation also leads to the systematic evolution of sand grain size (both on the bed and in suspension) in the Colorado River. Sand input during a tributary flood travels down the Colorado River as an elongating sediment wave, with the finest sizes (because of their lower settling velocities) traveling the fastest. As the fine front of a sediment wave arrives at a given location, the bed fines and suspended‐sand concentrations increase in response to the enhanced upstream supply of finer sand. Then, as the front of the sediment wave passes that location, the bed is winnowed and suspended‐sand concentrations decrease in response to the depletion of the upstream supply of finer sand. The grain‐size effects of depletion of the upstream sand supply are most obvious during periods of higher dam releases (e.g., the 1996 flood experiment and the 1997 test flow). Because of substantial changes in the grain‐size distribution of the bed, stable relationships between the discharge of water and sand‐transport rates (i.e., stable sand rating curves) are precluded. Sand budgets in a supply‐limited river like the Colorado River can only be constructed through inclusion of the physical processes that couple changes in bed‐sediment grain size to changes in sand‐transport rates.

Grain-Size-Limited Mobility in Methylammonium Lead Iodide Perovskite Thin Films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reid, Obadiah G.; Yang, Mengjin; Kopidakis, Nikos

2016-09-09

We report a systematic study of the gigahertz-frequency charge carrier mobility found in methylammonium lead iodide perovskite films as a function of average grain size using time-resolved microwave conductivity and a single processing chemistry. Our measurements are in good agreement with the Kubo formula for the AC mobility of charges confined within finite grains, suggesting (1) that the surface grains imaged via scanning electron microscopy are representative of the true electronic domain size and not substantially subdivided by twinning or other defects not visible by microscopy and (2) that the time scale of diffusive transport across grain boundaries is muchmore » slower than the period of the microwave field in this measurement (-100 ps). The intrinsic (infinite grain size) minimum mobility extracted form the model is 29 +/- 6 cm2 V-1 s-1 at the probe frequency (8.9 GHz).« less

Minimal size of coffee ring structure.

PubMed

Shen, Xiaoying; Ho, Chih-Ming; Wong, Tak-Sing

2010-04-29

A macroscopic evaporating water droplet with suspended particles on a solid surface will form a ring-like structure at the pinned contact line due to induced capillary flow. As the droplet size shrinks, the competition between the time scales of the liquid evaporation and the particle movement may influence the resulting ring formation. When the liquid evaporates much faster than the particle movement, coffee ring formation may cease. Here, we experimentally show that there exists a lower limit of droplet size, D(c), for the successful formation of a coffee ring structure. When the particle concentration is above a threshold value, D(c) can be estimated by considering the collective effects of the liquid evaporation and the particle diffusive motion within the droplet. For suspended particles of size approximately 100 nm, the minimum diameter of the coffee ring structure is found to be approximately 10 microm.

22 CFR 151.4 - Minimum limits for motor vehicle insurance.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Minimum limits for motor vehicle insurance. 151.4 Section 151.4 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.4 Minimum limits for motor vehicle...

22 CFR 151.4 - Minimum limits for motor vehicle insurance.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 22 Foreign Relations 1 2012-04-01 2012-04-01 false Minimum limits for motor vehicle insurance. 151.4 Section 151.4 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.4 Minimum limits for motor vehicle...

22 CFR 151.4 - Minimum limits for motor vehicle insurance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Minimum limits for motor vehicle insurance. 151.4 Section 151.4 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.4 Minimum limits for motor vehicle...

22 CFR 151.4 - Minimum limits for motor vehicle insurance.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Minimum limits for motor vehicle insurance. 151.4 Section 151.4 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.4 Minimum limits for motor vehicle...

22 CFR 151.4 - Minimum limits for motor vehicle insurance.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Minimum limits for motor vehicle insurance. 151.4 Section 151.4 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.4 Minimum limits for motor vehicle...

22 CFR 151.10 - Minimum limits of insurance for aircraft and/or vessels.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 22 Foreign Relations 1 2012-04-01 2012-04-01 false Minimum limits of insurance for aircraft and/or vessels. 151.10 Section 151.10 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.10 Minimum limits of insurance for...

22 CFR 151.10 - Minimum limits of insurance for aircraft and/or vessels.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Minimum limits of insurance for aircraft and/or vessels. 151.10 Section 151.10 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.10 Minimum limits of insurance for...

22 CFR 151.10 - Minimum limits of insurance for aircraft and/or vessels.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Minimum limits of insurance for aircraft and/or vessels. 151.10 Section 151.10 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.10 Minimum limits of insurance for...

22 CFR 151.10 - Minimum limits of insurance for aircraft and/or vessels.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Minimum limits of insurance for aircraft and/or vessels. 151.10 Section 151.10 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.10 Minimum limits of insurance for...

22 CFR 151.10 - Minimum limits of insurance for aircraft and/or vessels.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Minimum limits of insurance for aircraft and/or vessels. 151.10 Section 151.10 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.10 Minimum limits of insurance for...

Optimal Shape in Electromagnetic Scattering by Small Aspherical Particles

NASA Astrophysics Data System (ADS)

Kostinski, A. B.; Mongkolsittisilp, A.

2013-12-01

We consider the question of optimal shape for scattering by randomly oriented particles, e.g., shape causing minimal extinction among those of equal volume. Guided by the isoperimetric property of a sphere, relevant in the geometrical optics limit of scattering by large particles, we examine an analogous question in the low frequency (electrostatics) approximation, seeking to disentangle electric and geometric contributions. To that end, we survey the literature on shape functionals and focus on ellipsoids, giving a simple proof of spherical optimality for the coated ellipsoidal particle. Monotonic increase with asphericity in the low frequency regime for orientation-averaged induced dipole moments and scattering cross-sections is also established. Additional physical insight is obtained from the Rayleigh-Gans (transparent) limit and eccentricity expansions. We propose linking low and high frequency regime in a single minimum principle valid for all size parameters, provided that reasonable size distributions wash out the resonances for inter-mediate size parameters. This proposal is further supported by the sum rule for integrated extinction. Implications for spectro-polarimetric scattering are explicitly considered.

Climate and climate change and infectious disease risk in Thailand: A spatial study of dengue hemorrhagic fever using GIS and remotely-sensed imagery

NASA Astrophysics Data System (ADS)

Kuzera, Kristopher

The scientific community has widely accepted that climate plays a key role in the sustainability and transmission of many infectious diseases. Global climate change can potentially trigger the spread of disease into new regions and increase the intensity of disease in regions where it is endemic. This study explores the association between monthly conditions of climate change to changes in disease risk, emphasizing the potential spread of dengue fever due to climate change in Thailand. This study also develops techniques new to GIS and remote sensing that generate surfaces of daily minimum temperature toward identifying areas at greater transmission risk. Dengue fever expansion due to global warming is a serious concern for Thailand where warming temperatures may increase the size of the habitat of the disease-spreading vector, Aedes aegypti, particularly during cooler months when transmission is limited by environmental conditions. In this study, first, the association between past dengue hemorrhagic fever (DHF) and climate in Thailand is determined. Second, evidence of recent climate change is related to changes in DHF rates. Third, daily minimum temperature is derived from remote sensing toward identifying the spatial and temporal limitations of potential transmission risk. The results indicate that minimum temperature has recently experienced a rapid increase, particularly in the winter months when transmission is low. This is associated with a recent rise in winter DHF cases. As increasing minimum temperatures in these regions are anticipated to continue, we can expect dengue transmission rates to also increase throughout the year.

Synthetic control of the size, shape, and polydispersity of anisotropic silica colloids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, Ryan P.; Hong, Kunlun; Wagner, Norman J.

The particle size and shape determine the microstructure and rheological properties of colloidal suspensions. This work aims to further control the size, shape, and polydispersity of anisotropic silica colloids, to reduce particle size, and to provide additional mechanistic insights on a prevalent, water-in-oil emulsion synthesis method. Key findings show that the dimensions of anisotropic silica particles can be systematically varied by approximately fivefold, with a limiting minimum particle size (D ≈ 60 nm, L ≈ 300 nm) obtained from emulsions with excess polyvinylpyrrolidone (PVP) and sodium citrate. The synthesis conditions are identified and discussed for which the emulsion composition, temperature,more » sonication, polymer entanglements, mixing, and other perturbations may induce or mitigate emulsion instabilities, citrate precipitation, a competing mechanism of templated growth, termination of anisotropic growth, irregular silica structures, and fiber formation. An improved mechanistic understanding will expand the roadmap for rational design and synthetic control of anisotropic colloids using sol-gel silica chemistry confined within water-in-oil emulsions.« less

Synthetic control of the size, shape, and polydispersity of anisotropic silica colloids

DOE PAGES

Murphy, Ryan P.; Hong, Kunlun; Wagner, Norman J.

2017-09-01

The particle size and shape determine the microstructure and rheological properties of colloidal suspensions. This work aims to further control the size, shape, and polydispersity of anisotropic silica colloids, to reduce particle size, and to provide additional mechanistic insights on a prevalent, water-in-oil emulsion synthesis method. Key findings show that the dimensions of anisotropic silica particles can be systematically varied by approximately fivefold, with a limiting minimum particle size (D ≈ 60 nm, L ≈ 300 nm) obtained from emulsions with excess polyvinylpyrrolidone (PVP) and sodium citrate. The synthesis conditions are identified and discussed for which the emulsion composition, temperature,more » sonication, polymer entanglements, mixing, and other perturbations may induce or mitigate emulsion instabilities, citrate precipitation, a competing mechanism of templated growth, termination of anisotropic growth, irregular silica structures, and fiber formation. An improved mechanistic understanding will expand the roadmap for rational design and synthetic control of anisotropic colloids using sol-gel silica chemistry confined within water-in-oil emulsions.« less

Dose limited reliability of quantitative annular dark field scanning transmission electron microscopy for nano-particle atom-counting.

PubMed

De Backer, A; Martinez, G T; MacArthur, K E; Jones, L; Béché, A; Nellist, P D; Van Aert, S

2015-04-01

Quantitative annular dark field scanning transmission electron microscopy (ADF STEM) has become a powerful technique to characterise nano-particles on an atomic scale. Because of their limited size and beam sensitivity, the atomic structure of such particles may become extremely challenging to determine. Therefore keeping the incoming electron dose to a minimum is important. However, this may reduce the reliability of quantitative ADF STEM which will here be demonstrated for nano-particle atom-counting. Based on experimental ADF STEM images of a real industrial catalyst, we discuss the limits for counting the number of atoms in a projected atomic column with single atom sensitivity. We diagnose these limits by combining a thorough statistical method and detailed image simulations. Copyright © 2014 Elsevier B.V. All rights reserved.

Point Counts of Birds in Bottomland Hardwood Forests of the Mississippi Alluvial Valley: Duration, Minimum Sample Size, and Points Versus Visits

Treesearch

Winston Paul Smith; Daniel J. Twedt; David A. Wiedenfeld; Paul B. Hamel; Robert P. Ford; Robert J. Cooper

1993-01-01

To compare efficacy of point count sampling in bottomland hardwood forests, duration of point count, number of point counts, number of visits to each point during a breeding season, and minimum sample size are examined.

50 CFR 648.72 - Minimum surf clam size.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Atlantic Surf Clam and Ocean Quahog Fisheries § 648.72 Minimum surf clam size. Link to an amendment... quahog specifications. (a) Establishing catch quotas. The amount of surfclams or ocean quahogs that may... paragraph (b) of this section. The amount of surfclams available for harvest annually must be specified...

Correlation analysis of the optics of progressive addition lenses.

PubMed

Sheedy, James E

2004-05-01

To investigate the relations between selected key optical parameters and the sizes of the clear viewing areas of progressive addition lenses (PALs). The optics of 28 PALs (plano with +2.00 D add) currently on the market were measured with a Rotlex Class Plus lens analyzer. Horizontal cross sections were analyzed in 1 mm vertical steps with respect to the fitting cross. Distance, intermediate, and near viewing zone widths and areas were calculated from the measurements. The maximum amount of unwanted astigmatism, minimum zone width (0.50 DC limit), and maximum power rate in the corridor were also recorded for each lens. Correlation coefficients were determined for all relations. Each of the three viewing zone areas had a significant negative relation with the other (r of -0.4 to -0.8), indicating design tradeoff. Maximum power rate was significantly related to minimum zone width (r = -0.695), which was significantly related to maximum astigmatism (r = -0.616), but there was not a significant relation between maximum power rate and maximum astigmatism. Higher power rates and narrower minimum zones were significantly related to smaller intermediate and larger near zones (r = 0.4 to 0.9). Maximum astigmatism was related to distance zone width (r = 0.42) and to intermediate zone size (r = -0.4 to -0.56), but not significantly related to near viewing zone. Power rate and astigmatism each vary relatively uniformly across each lens. The fundamental relation appears to be between power rate and zone width, each of which is highly related to sizes of the intermediate and near viewing zones. The maximum amount of astigmatism is related to zone width, but not to maximum power rate. The amount of astigmatism is unrelated to the size of the near zone. The pattern of correlations between the optical and viewing zone parameters help identify the underlying optical relations of PALs.

Vision and the dimensions of nerve fibers.

PubMed

Wade, Nicholas J

2005-12-01

Vision provided the obvious source of determining the dimensions of nerve fibers when suitable achromatic microscopes were directed at neural tissue in the 1830s. The earlier microscopes of Hooke and Leeuwenhoek were unable to resolve such small structures adequately. However, it was not Hooke's microscope that led to an estimate of the dimensions of nerve fibers, but his experiments on the limits of visual resolution; he determined that a separation of one minute of arc was the minimum that could normally be seen. Descartes had earlier speculated that the retina consisted of the ends of fibers of the optic nerve, and that their size defined the limits of what could be seen. Estimates of the diameters of nerve fibers were made on the basis of human visual acuity by Porterfield in 1738; he calculated the diameters of nerve fibers in the retina as one 7,200th part of an inch (0.0035 mm), based on the resolution of one minute as the minimum visible. In the same year, Jurin questioned the reliability of such estimates because of variations in visual resolution with different stimuli.

Examining the Prey Mass of Terrestrial and Aquatic Carnivorous Mammals: Minimum, Maximum and Range

PubMed Central

Tucker, Marlee A.; Rogers, Tracey L.

2014-01-01

Predator-prey body mass relationships are a vital part of food webs across ecosystems and provide key information for predicting the susceptibility of carnivore populations to extinction. Despite this, there has been limited research on the minimum and maximum prey size of mammalian carnivores. Without information on large-scale patterns of prey mass, we limit our understanding of predation pressure, trophic cascades and susceptibility of carnivores to decreasing prey populations. The majority of studies that examine predator-prey body mass relationships focus on either a single or a subset of mammalian species, which limits the strength of our models as well as their broader application. We examine the relationship between predator body mass and the minimum, maximum and range of their prey's body mass across 108 mammalian carnivores, from weasels to baleen whales (Carnivora and Cetacea). We test whether mammals show a positive relationship between prey and predator body mass, as in reptiles and birds, as well as examine how environment (aquatic and terrestrial) and phylogenetic relatedness play a role in this relationship. We found that phylogenetic relatedness is a strong driver of predator-prey mass patterns in carnivorous mammals and accounts for a higher proportion of variance compared with the biological drivers of body mass and environment. We show a positive predator-prey body mass pattern for terrestrial mammals as found in reptiles and birds, but no relationship for aquatic mammals. Our results will benefit our understanding of trophic interactions, the susceptibility of carnivores to population declines and the role of carnivores within ecosystems. PMID:25162695

Examining the prey mass of terrestrial and aquatic carnivorous mammals: minimum, maximum and range.

PubMed

Tucker, Marlee A; Rogers, Tracey L

2014-01-01

Predator-prey body mass relationships are a vital part of food webs across ecosystems and provide key information for predicting the susceptibility of carnivore populations to extinction. Despite this, there has been limited research on the minimum and maximum prey size of mammalian carnivores. Without information on large-scale patterns of prey mass, we limit our understanding of predation pressure, trophic cascades and susceptibility of carnivores to decreasing prey populations. The majority of studies that examine predator-prey body mass relationships focus on either a single or a subset of mammalian species, which limits the strength of our models as well as their broader application. We examine the relationship between predator body mass and the minimum, maximum and range of their prey's body mass across 108 mammalian carnivores, from weasels to baleen whales (Carnivora and Cetacea). We test whether mammals show a positive relationship between prey and predator body mass, as in reptiles and birds, as well as examine how environment (aquatic and terrestrial) and phylogenetic relatedness play a role in this relationship. We found that phylogenetic relatedness is a strong driver of predator-prey mass patterns in carnivorous mammals and accounts for a higher proportion of variance compared with the biological drivers of body mass and environment. We show a positive predator-prey body mass pattern for terrestrial mammals as found in reptiles and birds, but no relationship for aquatic mammals. Our results will benefit our understanding of trophic interactions, the susceptibility of carnivores to population declines and the role of carnivores within ecosystems.

Predicting paddlefish roe yields using an extension of the Beverton–Holt equilibrium yield-per-recruit model

USGS Publications Warehouse

Colvin, M.E.; Bettoli, Phillip William; Scholten, G.D.

2013-01-01

Equilibrium yield models predict the total biomass removed from an exploited stock; however, traditional yield models must be modified to simulate roe yields because a linear relationship between age (or length) and mature ovary weight does not typically exist. We extended the traditional Beverton-Holt equilibrium yield model to predict roe yields of Paddlefish Polyodon spathula in Kentucky Lake, Tennessee-Kentucky, as a function of varying conditional fishing mortality rates (10-70%), conditional natural mortality rates (cm; 9% and 18%), and four minimum size limits ranging from 864 to 1,016mm eye-to-fork length. These results were then compared to a biomass-based yield assessment. Analysis of roe yields indicated the potential for growth overfishing at lower exploitation rates and smaller minimum length limits than were suggested by the biomass-based assessment. Patterns of biomass and roe yields in relation to exploitation rates were similar regardless of the simulated value of cm, thus indicating that the results were insensitive to changes in cm. Our results also suggested that higher minimum length limits would increase roe yield and reduce the potential for growth overfishing and recruitment overfishing at the simulated cm values. Biomass-based equilibrium yield assessments are commonly used to assess the effects of harvest on other caviar-based fisheries; however, our analysis demonstrates that such assessments likely underestimate the probability and severity of growth overfishing when roe is targeted. Therefore, equilibrium roe yield-per-recruit models should also be considered to guide the management process for caviar-producing fish species.

48 CFR 52.247-61 - F.o.b. Origin-Minimum Size of Shipments.

Code of Federal Regulations, 2011 CFR

2011-10-01

... be the highest applicable minimum weight which will result in the lowest freight rate (or per car... minimum weight, the Contractor agrees to ship such scheduled quantity in one shipment. The Contractor...

48 CFR 52.247-61 - F.o.b. Origin-Minimum Size of Shipments.

Code of Federal Regulations, 2013 CFR

2013-10-01

... be the highest applicable minimum weight which will result in the lowest freight rate (or per car... minimum weight, the Contractor agrees to ship such scheduled quantity in one shipment. The Contractor...

48 CFR 52.247-61 - F.o.b. Origin-Minimum Size of Shipments.

Code of Federal Regulations, 2014 CFR

2014-10-01

... be the highest applicable minimum weight which will result in the lowest freight rate (or per car... minimum weight, the Contractor agrees to ship such scheduled quantity in one shipment. The Contractor...

48 CFR 52.247-61 - F.o.b. Origin-Minimum Size of Shipments.

Code of Federal Regulations, 2012 CFR

2012-10-01

... be the highest applicable minimum weight which will result in the lowest freight rate (or per car... minimum weight, the Contractor agrees to ship such scheduled quantity in one shipment. The Contractor...

Choice of Stimulus Range and Size Can Reduce Test-Retest Variability in Glaucomatous Visual Field Defects

PubMed Central

Swanson, William H.; Horner, Douglas G.; Dul, Mitchell W.; Malinovsky, Victor E.

2014-01-01

Purpose To develop guidelines for engineering perimetric stimuli to reduce test-retest variability in glaucomatous defects. Methods Perimetric testing was performed on one eye for 62 patients with glaucoma and 41 age-similar controls on size III and frequency-doubling perimetry and three custom tests with Gaussian blob and Gabor sinusoid stimuli. Stimulus range was controlled by values for ceiling (maximum sensitivity) and floor (minimum sensitivity). Bland-Altman analysis was used to derive 95% limits of agreement on test and retest, and bootstrap analysis was used to test the hypotheses about peak variability. Results Limits of agreement for the three custom stimuli were similar in width (0.72 to 0.79 log units) and peak variability (0.22 to 0.29 log units) for a stimulus range of 1.7 log units. The width of the limits of agreement for size III decreased from 1.78 to 1.37 to 0.99 log units for stimulus ranges of 3.9, 2.7, and 1.7 log units, respectively (F = 3.23, P < 0.001); peak variability was 0.99, 0.54, and 0.34 log units, respectively (P < 0.01). For a stimulus range of 1.3 log units, limits of agreement were narrowest with Gabor and widest with size III stimuli, and peak variability was lower (P < 0.01) with Gabor (0.18 log units) and frequency-doubling perimetry (0.24 log units) than with size III stimuli (0.38 log units). Conclusions Test-retest variability in glaucomatous visual field defects was substantially reduced by engineering the stimuli. Translational Relevance The guidelines should allow developers to choose from a wide range of stimuli. PMID:25371855

Choice of Stimulus Range and Size Can Reduce Test-Retest Variability in Glaucomatous Visual Field Defects.

PubMed

Swanson, William H; Horner, Douglas G; Dul, Mitchell W; Malinovsky, Victor E

2014-09-01

To develop guidelines for engineering perimetric stimuli to reduce test-retest variability in glaucomatous defects. Perimetric testing was performed on one eye for 62 patients with glaucoma and 41 age-similar controls on size III and frequency-doubling perimetry and three custom tests with Gaussian blob and Gabor sinusoid stimuli. Stimulus range was controlled by values for ceiling (maximum sensitivity) and floor (minimum sensitivity). Bland-Altman analysis was used to derive 95% limits of agreement on test and retest, and bootstrap analysis was used to test the hypotheses about peak variability. Limits of agreement for the three custom stimuli were similar in width (0.72 to 0.79 log units) and peak variability (0.22 to 0.29 log units) for a stimulus range of 1.7 log units. The width of the limits of agreement for size III decreased from 1.78 to 1.37 to 0.99 log units for stimulus ranges of 3.9, 2.7, and 1.7 log units, respectively ( F = 3.23, P < 0.001); peak variability was 0.99, 0.54, and 0.34 log units, respectively ( P < 0.01). For a stimulus range of 1.3 log units, limits of agreement were narrowest with Gabor and widest with size III stimuli, and peak variability was lower ( P < 0.01) with Gabor (0.18 log units) and frequency-doubling perimetry (0.24 log units) than with size III stimuli (0.38 log units). Test-retest variability in glaucomatous visual field defects was substantially reduced by engineering the stimuli. The guidelines should allow developers to choose from a wide range of stimuli.

Exploratory Factor Analysis with Small Sample Sizes

ERIC Educational Resources Information Center

de Winter, J. C. F.; Dodou, D.; Wieringa, P. A.

2009-01-01

Exploratory factor analysis (EFA) is generally regarded as a technique for large sample sizes ("N"), with N = 50 as a reasonable absolute minimum. This study offers a comprehensive overview of the conditions in which EFA can yield good quality results for "N" below 50. Simulations were carried out to estimate the minimum required "N" for different…

46 CFR 111.60-4 - Minimum cable conductor size.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Minimum cable conductor size. 111.60-4 Section 111.60-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS... conductor must be #18 AWG (0.82 mm2) or larger except— (a) Each power and lighting cable conductor must be...

46 CFR 111.60-4 - Minimum cable conductor size.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Minimum cable conductor size. 111.60-4 Section 111.60-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS... conductor must be #18 AWG (0.82 mm2) or larger except— (a) Each power and lighting cable conductor must be...

46 CFR 111.60-4 - Minimum cable conductor size.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Minimum cable conductor size. 111.60-4 Section 111.60-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS... conductor must be #18 AWG (0.82 mm2) or larger except— (a) Each power and lighting cable conductor must be...

7 CFR 51.1995 - U.S. No. 1.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Well formed; and, (2) Clean and bright. (3) Free from: (i) Blanks; and, (ii) Broken or split shells. (4... minimum diameter, minimum and maximum diameters, or in accordance with one of the size classifications in Table I. Table I Size classifications Maximum size—Will pass through a round opening of the following...

78 FR 52079 - Oranges, Grapefruit, Tangerines, and Tangelos Grown in Florida; Relaxing Size and Grade...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-22

... Requirements on Valencia and Other Late Type Oranges AGENCY: Agricultural Marketing Service, USDA. ACTION...). The interim rule reduced the minimum size for Valencia and other late type oranges shipped to... interim rule also lowered the minimum grade for Valencia and other late type oranges shipped to interstate...

78 FR 28115 - Oranges, Grapefruit, Tangerines, and Tangelos Grown in Florida; Relaxing Size and Grade...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-14

... Requirements on Valencia and Other Late Type Oranges AGENCY: Agricultural Marketing Service, USDA. ACTION...). This rule reduces the minimum size requirement for Valencia and other late type oranges shipped to... also reduces the minimum grade requirement for Valencia and other late type oranges shipped to...

76 FR 37867 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Order Approving...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-28

..., as Modified by Amendment No. 1, to Reduce the Minimum Size of the Nominating and Governance Committee... proposed rule change to reduce the minimum size of the Nominating and Governance Committee (``NGC'') from... the original proposed rule change, it had not yet obtained formal approval from its Board of Directors...

7 CFR 51.2113 - Size requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... of range in count of whole almond kernels per ounce or in terms of minimum, or minimum and maximum diameter. When a range in count is specified, the whole kernels shall be fairly uniform in size, and the average count per ounce shall be within the range specified. Doubles and broken kernels shall not be used...

How far and how fast can mushroom spores fly? Physical limits on ballistospore size and discharge distance in the Basidiomycota

PubMed Central

Fischer, Mark W. F.; Stolze-Rybczynski, Jessica L.; Cui, Yunluan; Money, Nicholas P.

2010-01-01

Active discharge of basidiospores in most species of Basidiomycota is powered by the rapid movement of a droplet of fluid, called Buller’s drop, over the spore surface. This paper is concerned with the operation of the launch mechanism in species with the largest and smallest ballistospores. Aleurodiscus gigasporus (Russulales) produces the largest basidiospores on record. The maximum dimensions of the spores, 34 × 28 µm, correspond to a volume of 14 pL and to an estimated mass of 17 ng. The smallest recorded basidiospores are produced by Hyphodontia latitans (Hymenochaetales). Minimum spore dimensions in this species, 3.5 × 0.5 µm, correspond to a volume of 0.5 fL and mass of 0.6 pg. Neither species has been studied using high-speed video microscopy, but this technique was used to examine ballistospore discharge in species with spores of similar sizes (slightly smaller than A. gigasporus and slightly larger than those of H. latitans). Extrapolation of velocity measurements from these fungi provided estimates of discharge distances ranging from a maximum of almost 2 mm in A. gigasporus to a minimum of 4 µm in H. latitans. These are, respectively, the longest and shortest predicted discharge distances for ballistospores. Limitations to the distances traveled by basidiospores are discussed in relation to the mechanics of the discharge process and the types of fruit-bodies from which the spores are released. PMID:20835365

Dependence of the quantum speed limit on system size and control complexity

NASA Astrophysics Data System (ADS)

Lee, Juneseo; Arenz, Christian; Rabitz, Herschel; Russell, Benjamin

2018-06-01

We extend the work in 2017 New J. Phys. 19 103015 by deriving a lower bound for the minimum time necessary to implement a unitary transformation on a generic, closed quantum system with an arbitrary number of classical control fields. This bound is explicitly analyzed for a specific N-level system similar to those used to represent simple models of an atom, or the first excitation sector of a Heisenberg spin chain, both of which are of interest in quantum control for quantum computation. Specifically, it is shown that the resultant bound depends on the dimension of the system, and on the number of controls used to implement a specific target unitary operation. The value of the bound determined numerically, and an estimate of the true minimum gate time are systematically compared for a range of system dimension and number of controls; special attention is drawn to the relationship between these two variables. It is seen that the bound captures the scaling of the minimum time well for the systems studied, and quantitatively is correct in the order of magnitude.

Trophy Hunting and Sustainability: Temporal Dynamics in Trophy Quality and Harvesting Patterns of Wild Herbivores in a Tropical Semi-Arid Savanna Ecosystem.

PubMed

Muposhi, Victor K; Gandiwa, Edson; Bartels, Paul; Makuza, Stanley M; Madiri, Tinaapi H

2016-01-01

The selective nature of trophy hunting may cause changes in desirable phenotypic traits in harvested species. A decline in trophy size of preferred species may reduce hunting destination competitiveness thus compromising the sustainability of trophy hunting as a conservation tool. We explored the trophy quality and trends in harvesting patterns (i.e., 2004-2015) of Cape buffalo (Syncerus caffer), African elephant (Loxodonta africana), greater kudu (Tragelaphus strepsiceros) and sable (Hippotragus niger) in Matetsi Safari Area, northwest Zimbabwe. We used long-term data on horn and tusk size, age, quota size allocation and offtake levels of selected species. To analyse the effect of year, area and age on the trophy size, quota size and offtake levels, we used linear mixed models. One sample t-test was used to compare observed trophy size with Safari Club International (SCI) minimum score. Trophy sizes for Cape buffalo and African elephant were below the SCI minimum score. Greater kudu trophy sizes were within the minimum score threshold whereas sable trophy sizes were above the SCI minimum score between 2004 and 2015. Age at harvest for Cape buffalo, kudu and sable increased whilst that of elephant remained constant between 2004 and 2015. Quota size allocated for buffalo and the corresponding offtake levels declined over time. Offtake levels of African elephant and Greater kudu declined whilst the quota size did not change between 2004 and 2015. The quota size for sable increased whilst the offtake levels fluctuated without changing for the period 2004-2015. The trophy size and harvesting patterns in these species pose a conservation and management dilemma on the sustainability of trophy hunting in this area. We recommend: (1) temporal and spatial rotational resting of hunting areas to create refuge to improve trophy quality and maintenance of genetic diversity, and (2) introduction of variable trophy fee pricing system based on trophy size.

A mixed-integer linear programming approach to the reduction of genome-scale metabolic networks.

PubMed

Röhl, Annika; Bockmayr, Alexander

2017-01-03

Constraint-based analysis has become a widely used method to study metabolic networks. While some of the associated algorithms can be applied to genome-scale network reconstructions with several thousands of reactions, others are limited to small or medium-sized models. In 2015, Erdrich et al. introduced a method called NetworkReducer, which reduces large metabolic networks to smaller subnetworks, while preserving a set of biological requirements that can be specified by the user. Already in 2001, Burgard et al. developed a mixed-integer linear programming (MILP) approach for computing minimal reaction sets under a given growth requirement. Here we present an MILP approach for computing minimum subnetworks with the given properties. The minimality (with respect to the number of active reactions) is not guaranteed by NetworkReducer, while the method by Burgard et al. does not allow specifying the different biological requirements. Our procedure is about 5-10 times faster than NetworkReducer and can enumerate all minimum subnetworks in case there exist several ones. This allows identifying common reactions that are present in all subnetworks, and reactions appearing in alternative pathways. Applying complex analysis methods to genome-scale metabolic networks is often not possible in practice. Thus it may become necessary to reduce the size of the network while keeping important functionalities. We propose a MILP solution to this problem. Compared to previous work, our approach is more efficient and allows computing not only one, but even all minimum subnetworks satisfying the required properties.

Contactless transport of matter in the first five resonance modes of a line-focused acoustic manipulator.

PubMed

Foresti, Daniele; Nabavi, Majid; Poulikakos, Dimos

2012-02-01

The first five resonance modes for transport of matter in a line-focused acoustic levitation system are investigated. Contactless transport was achieved by varying the height between the radiating plate and the reflector. Transport and levitation of droplets in particular involve two limits of the acoustic forces. The lower limit corresponds to the minimum force required to overcome the gravitational force. The upper limit corresponds to the maximum acoustic pressure beyond which atomization of the droplet occurs. As the droplet size increases, the lower limit increases and the upper limit decreases. Therefore to have large droplets levitated, relatively flat radiation pressure amplitude during the translation is needed. In this study, using a finite element model, the Gor'kov potential was calculated for different heights between the reflector and the radiating plate. The application of the Gor'kov potential was extended to study the range of droplet sizes for which the droplets can be levitated and transported without atomization. It was found that the third resonant mode (H(3)-mode) represents the best compromise between high levitation force and smooth pattern transition, and water droplets of millimeter radius can be levitated and transported. The H(3)-mode also allows for three translation lines in parallel. © 2012 Acoustical Society of America

Power Distribution System Planning with GIS Consideration

NASA Astrophysics Data System (ADS)

Wattanasophon, Sirichai; Eua-Arporn, Bundhit

This paper proposes a method for solving radial distribution system planning problems taking into account geographical information. The proposed method can automatically determine appropriate location and size of a substation, routing of feeders, and sizes of conductors while satisfying all constraints, i.e. technical constraints (voltage drop and thermal limit) and geographical constraints (obstacle, existing infrastructure, and high-cost passages). Sequential quadratic programming (SQP) and minimum path algorithm (MPA) are applied to solve the planning problem based on net price value (NPV) consideration. In addition this method integrates planner's experience and optimization process to achieve an appropriate practical solution. The proposed method has been tested with an actual distribution system, from which the results indicate that it can provide satisfactory plans.

Biodiversity and body size are linked across metazoans

PubMed Central

McClain, Craig R.; Boyer, Alison G.

2009-01-01

Body size variation across the Metazoa is immense, encompassing 17 orders of magnitude in biovolume. Factors driving this extreme diversification in size and the consequences of size variation for biological processes remain poorly resolved. Species diversity is invoked as both a predictor and a result of size variation, and theory predicts a strong correlation between the two. However, evidence has been presented both supporting and contradicting such a relationship. Here, we use a new comprehensive dataset for maximum and minimum body sizes across all metazoan phyla to show that species diversity is strongly correlated with minimum size, maximum size and consequently intra-phylum variation. Similar patterns are also observed within birds and mammals. The observations point to several fundamental linkages between species diversification and body size variation through the evolution of animal life. PMID:19324730

LDPC Codes with Minimum Distance Proportional to Block Size

NASA Technical Reports Server (NTRS)

Divsalar, Dariush; Jones, Christopher; Dolinar, Samuel; Thorpe, Jeremy

2009-01-01

Low-density parity-check (LDPC) codes characterized by minimum Hamming distances proportional to block sizes have been demonstrated. Like the codes mentioned in the immediately preceding article, the present codes are error-correcting codes suitable for use in a variety of wireless data-communication systems that include noisy channels. The previously mentioned codes have low decoding thresholds and reasonably low error floors. However, the minimum Hamming distances of those codes do not grow linearly with code-block sizes. Codes that have this minimum-distance property exhibit very low error floors. Examples of such codes include regular LDPC codes with variable degrees of at least 3. Unfortunately, the decoding thresholds of regular LDPC codes are high. Hence, there is a need for LDPC codes characterized by both low decoding thresholds and, in order to obtain acceptably low error floors, minimum Hamming distances that are proportional to code-block sizes. The present codes were developed to satisfy this need. The minimum Hamming distances of the present codes have been shown, through consideration of ensemble-average weight enumerators, to be proportional to code block sizes. As in the cases of irregular ensembles, the properties of these codes are sensitive to the proportion of degree-2 variable nodes. A code having too few such nodes tends to have an iterative decoding threshold that is far from the capacity threshold. A code having too many such nodes tends not to exhibit a minimum distance that is proportional to block size. Results of computational simulations have shown that the decoding thresholds of codes of the present type are lower than those of regular LDPC codes. Included in the simulations were a few examples from a family of codes characterized by rates ranging from low to high and by thresholds that adhere closely to their respective channel capacity thresholds; the simulation results from these examples showed that the codes in question have low error floors as well as low decoding thresholds. As an example, the illustration shows the protograph (which represents the blueprint for overall construction) of one proposed code family for code rates greater than or equal to 1.2. Any size LDPC code can be obtained by copying the protograph structure N times, then permuting the edges. The illustration also provides Field Programmable Gate Array (FPGA) hardware performance simulations for this code family. In addition, the illustration provides minimum signal-to-noise ratios (Eb/No) in decibels (decoding thresholds) to achieve zero error rates as the code block size goes to infinity for various code rates. In comparison with the codes mentioned in the preceding article, these codes have slightly higher decoding thresholds.

Wavelet data compression for archiving high-resolution icosahedral model data

NASA Astrophysics Data System (ADS)

Wang, N.; Bao, J.; Lee, J.

2011-12-01

With the increase of the resolution of global circulation models, it becomes ever more important to develop highly effective solutions to archive the huge datasets produced by those models. While lossless data compression guarantees the accuracy of the restored data, it can only achieve limited reduction of data size. Wavelet transform based data compression offers significant potentials in data size reduction, and it has been shown very effective in transmitting data for remote visualizations. However, for data archive purposes, a detailed study has to be conducted to evaluate its impact to the datasets that will be used in further numerical computations. In this study, we carried out two sets of experiments for both summer and winter seasons. An icosahedral grid weather model and a highly efficient wavelet data compression software were used for this study. Initial conditions were compressed and input to the model to run to 10 days. The forecast results were then compared to those forecast results from the model run with the original uncompressed initial conditions. Several visual comparisons, as well as the statistics of numerical comparisons are presented. These results indicate that with specified minimum accuracy losses, wavelet data compression achieves significant data size reduction, and at the same time, it maintains minimum numerical impacts to the datasets. In addition, some issues are discussed to increase the archive efficiency while retaining a complete set of meta data for each archived file.

The Minimum Binding Energy and Size of Doubly Muonic D3 Molecule

NASA Astrophysics Data System (ADS)

Eskandari, M. R.; Faghihi, F.; Mahdavi, M.

The minimum energy and size of doubly muonic D3 molecule, which two of the electrons are replaced by the much heavier muons, are calculated by the well-known variational method. The calculations show that the system possesses two minimum positions, one at typically muonic distance and the second at the atomic distance. It is shown that at the muonic distance, the effective charge, zeff is 2.9. We assumed a symmetric planar vibrational model between two minima and an oscillation potential energy is approximated in this region.

Hierarchical complexity and the size limits of life.

PubMed

Heim, Noel A; Payne, Jonathan L; Finnegan, Seth; Knope, Matthew L; Kowalewski, Michał; Lyons, S Kathleen; McShea, Daniel W; Novack-Gottshall, Philip M; Smith, Felisa A; Wang, Steve C

2017-06-28

Over the past 3.8 billion years, the maximum size of life has increased by approximately 18 orders of magnitude. Much of this increase is associated with two major evolutionary innovations: the evolution of eukaryotes from prokaryotic cells approximately 1.9 billion years ago (Ga), and multicellular life diversifying from unicellular ancestors approximately 0.6 Ga. However, the quantitative relationship between organismal size and structural complexity remains poorly documented. We assessed this relationship using a comprehensive dataset that includes organismal size and level of biological complexity for 11 172 extant genera. We find that the distributions of sizes within complexity levels are unimodal, whereas the aggregate distribution is multimodal. Moreover, both the mean size and the range of size occupied increases with each additional level of complexity. Increases in size range are non-symmetric: the maximum organismal size increases more than the minimum. The majority of the observed increase in organismal size over the history of life on the Earth is accounted for by two discrete jumps in complexity rather than evolutionary trends within levels of complexity. Our results provide quantitative support for an evolutionary expansion away from a minimal size constraint and suggest a fundamental rescaling of the constraints on minimal and maximal size as biological complexity increases. © 2017 The Author(s).

77 FR 23770 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-20

... to Proposed Rule Change To Amend FINRA Rule 6433 (Minimum Quotation Size Requirements for OTC Equity... proposed rule change to amend FINRA Rule 6433 (Minimum Quotation Size Requirements for OTC Equity... investors, three from an inter-dealer quotation system and two from a member firm.\\4\\ FINRA responded to...

50 CFR 648.104 - Summer flounder minimum fish sizes.

Code of Federal Regulations, 2012 CFR

2012-10-01

....99 cm) TL for all vessels that do not qualify for a moratorium permit under § 648.4(a)(3), and... (commercial) permitted vessels. The minimum size for summer flounder is 14 inches (35.6 cm) TL for all vessels issued a moratorium permit under § 648.4(a)(3), except on board party and charter boats carrying...

50 CFR 648.104 - Summer flounder minimum fish sizes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cm) TL for all vessels that do not qualify for a moratorium permit under § 648.4(a)(3), and charter... (commercial) permitted vessels. The minimum size for summer flounder is 14 inches (35.6 cm) TL for all vessels issued a moratorium permit under § 648.4(a)(3), except on board party and charter boats carrying...

50 CFR 648.104 - Summer flounder minimum fish sizes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... cm) TL for all vessels that do not qualify for a moratorium permit under § 648.4(a)(3), and charter... (commercial) permitted vessels. The minimum size for summer flounder is 14 inches (35.6 cm) TL for all vessels issued a moratorium permit under § 648.4(a)(3), except on board party and charter boats carrying...

An injectable acoustic transmitter for juvenile salmon

DOE PAGES

Deng, Zhiqun; Carlson, Thomas J.; Li, Huidong; ...

2015-01-29

Salmon recovery, and the potential detrimental effects of dams on fish, has been attracting national attention in due to great environmental and economic implications. Acoustic Telemetry has been the primary method for studying salmon passage. However, the size of the existing transmitters limits the minimum size of fish that can be studied, introducing bias to the study results. We developed the first acoustic fish transmitter that can be implanted by injection instead of surgery. The new injectable transmitter offers improved performance and 30% weight reduction. Because the new transmitter costs significantly less to use, substantially reduces adverse effects of implantation,more » and provides additional biological benefits for tagged fish, it will become the enabling technology for studying migration behavior and survival of species and sizes of fish that have never been studied before. This will lead to critical information for salmon recovery and the development of fish-friendly hydroelectric systems.« less

An injectable acoustic transmitter for juvenile salmon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Zhiqun; Carlson, Thomas J.; Li, Huidong

Salmon recovery, and the potential detrimental effects of dams on fish, has been attracting national attention in due to great environmental and economic implications. Acoustic Telemetry has been the primary method for studying salmon passage. However, the size of the existing transmitters limits the minimum size of fish that can be studied, introducing bias to the study results. We developed the first acoustic fish transmitter that can be implanted by injection instead of surgery. The new injectable transmitter offers improved performance and 30% weight reduction. Because the new transmitter costs significantly less to use, substantially reduces adverse effects of implantation,more » and provides additional biological benefits for tagged fish, it will become the enabling technology for studying migration behavior and survival of species and sizes of fish that have never been studied before. This will lead to critical information for salmon recovery and the development of fish-friendly hydroelectric systems.« less

MIMO equalization with adaptive step size for few-mode fiber transmission systems.

PubMed

van Uden, Roy G H; Okonkwo, Chigo M; Sleiffer, Vincent A J M; de Waardt, Hugo; Koonen, Antonius M J

2014-01-13

Optical multiple-input multiple-output (MIMO) transmission systems generally employ minimum mean squared error time or frequency domain equalizers. Using an experimental 3-mode dual polarization coherent transmission setup, we show that the convergence time of the MMSE time domain equalizer (TDE) and frequency domain equalizer (FDE) can be reduced by approximately 50% and 30%, respectively. The criterion used to estimate the system convergence time is the time it takes for the MIMO equalizer to reach an average output error which is within a margin of 5% of the average output error after 50,000 symbols. The convergence reduction difference between the TDE and FDE is attributed to the limited maximum step size for stable convergence of the frequency domain equalizer. The adaptive step size requires a small overhead in the form of a lookup table. It is highlighted that the convergence time reduction is achieved without sacrificing optical signal-to-noise ratio performance.

An injectable acoustic transmitter for juvenile salmon

NASA Astrophysics Data System (ADS)

Deng, Z. D.; Carlson, T. J.; Li, H.; Xiao, J.; Myjak, M. J.; Lu, J.; Martinez, J. J.; Woodley, C. M.; Weiland, M. A.; Eppard, M. B.

2015-01-01

Salmon recovery and the potential detrimental effects of dams on fish have been attracting national attention due to the environmental and economic implications. In recent years acoustic telemetry has been the primary method for studying salmon passage. However, the size of the existing transmitters limits the minimum size of fish that can be studied, introducing a bias to the study results. We developed the first acoustic fish transmitter that can be implanted by injection instead of surgery. The new injectable transmitter lasts four times longer and weighs 30% less than other transmitters. Because the new transmitter costs significantly less to use and may substantially reduce adverse effects of implantation and tag burden, it will allow for study of migration behavior and survival of species and sizes of fish that have never been studied before. The new technology will lead to critical information needed for salmon recovery and the development of fish-friendly hydroelectric systems.

An injectable acoustic transmitter for juvenile salmon

PubMed Central

Deng, Z. D.; Carlson, T. J.; Li, H.; Xiao, J.; Myjak, M. J.; Lu, J.; Martinez, J. J.; Woodley, C. M.; Weiland, M. A.; Eppard, M. B.

2015-01-01

Salmon recovery and the potential detrimental effects of dams on fish have been attracting national attention due to the environmental and economic implications. In recent years acoustic telemetry has been the primary method for studying salmon passage. However, the size of the existing transmitters limits the minimum size of fish that can be studied, introducing a bias to the study results. We developed the first acoustic fish transmitter that can be implanted by injection instead of surgery. The new injectable transmitter lasts four times longer and weighs 30% less than other transmitters. Because the new transmitter costs significantly less to use and may substantially reduce adverse effects of implantation and tag burden, it will allow for study of migration behavior and survival of species and sizes of fish that have never been studied before. The new technology will lead to critical information needed for salmon recovery and the development of fish-friendly hydroelectric systems. PMID:25630763

Small fan-in is beautiful

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beiu, V.; Makaruk, H.E.

1997-09-01

The starting points of this paper are two size-optimal solutions: (1) one for implementing arbitrary Boolean functions; and (2) another one for implementing certain subclasses of Boolean functions. Because VLSI implementations do not cope well with highly interconnected nets -- the area of a chip grows with the cube of the fan-in -- this paper will analyze the influence of limited fan-in on the size optimality for the two solutions mentioned. First, the authors will extend a result from Horne and Hush valid for fan-in {Delta} = 2 to arbitrary fan-in. Second, they will prove that size-optimal solutions are obtainedmore » for small constant fan-ins for both constructions, while relative minimum size solutions can be obtained for fan-ins strictly lower that linear. These results are in agreement with similar ones proving that for small constant fan-ins ({Delta} = 6...9) there exist VLSI-optimal (i.e., minimizing AT{sup 2}) solutions, while there are similar small constants relating to the capacity of processing information.« less

Constraints on the adult-offspring size relationship in protists.

PubMed

Caval-Holme, Franklin; Payne, Jonathan; Skotheim, Jan M

2013-12-01

The relationship between adult and offspring size is an important aspect of reproductive strategy. Although this filial relationship has been extensively examined in plants and animals, we currently lack comparable data for protists, whose strategies may differ due to the distinct ecological and physiological constraints on single-celled organisms. Here, we report measurements of adult and offspring sizes in 3888 species and subspecies of foraminifera, a class of large marine protists. Foraminifera exhibit a wide range of reproductive strategies; species of similar adult size may have offspring whose sizes vary 100-fold. Yet, a robust pattern emerges. The minimum (5th percentile), median, and maximum (95th percentile) offspring sizes exhibit a consistent pattern of increase with adult size independent of environmental change and taxonomic variation over the past 400 million years. The consistency of this pattern may arise from evolutionary optimization of the offspring size-fecundity trade-off and/or from cell-biological constraints that limit the range of reproductive strategies available to single-celled organisms. When compared with plants and animals, foraminifera extend the evidence that offspring size covaries with adult size across an additional five orders of magnitude in organism size. © 2013 The Author(s). Evolution © 2013 The Society for the Study of Evolution.

Fracture control for the Oman India Pipeline

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruno, T.V.

1996-12-31

This paper describes the evaluation of the resistance to fracture initiation and propagation for the high-strength, heavy-wall pipe required for the Oman India Pipeline (OIP). It discusses the unique aspects of this pipeline and their influence on fracture control, reviews conventional fracture control design methods, their limitations with regard to the pipe in question, the extent to which they can be utilized for this project, and other approaches being explored. Test pipe of the size and grade required for the OIP show fracture toughness well in excess of the minimum requirements.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loef, P.A.; Smed, T.; Andersson, G.

The minimum singular value of the power flow Jacobian matrix has been used as a static voltage stability index, indicating the distance between the studied operating point and the steady state voltage stability limit. In this paper a fast method to calculate the minimum singular value and the corresponding (left and right) singular vectors is presented. The main advantages of the developed algorithm are the small amount of computation time needed, and that it only requires information available from an ordinary program for power flow calculations. Furthermore, the proposed method fully utilizes the sparsity of the power flow Jacobian matrixmore » and hence the memory requirements for the computation are low. These advantages are preserved when applied to various submatrices of the Jacobian matrix, which can be useful in constructing special voltage stability indices. The developed algorithm was applied to small test systems as well as to a large (real size) system with over 1000 nodes, with satisfactory results.« less

Analysis and sizing of Mars aerobrake structure

NASA Technical Reports Server (NTRS)

Raju, I. S.; Craft, W. J.

1993-01-01

A cone-sphere aeroshell structure for aerobraking into Martian atmosphere is studied. Using this structural configuration, a space frame load-bearing structure is proposed. To generate this structure efficiently and to perform a variety of studies of several configurations, a mesh generator that utilizes only a few configurational parameters is developed. A finite element analysis program that analyzes space frame structures was developed. A sizing algorithm that arrives at a minimum mass configuration was developed and integrated into the finite element analysis program. A typical 135-ft-diam aerobrake configuration was analyzed and sized. The minimum mass obtained in this study using high modulus graphite/epoxy composite material members is compared with the masses obtained from two other aerobrake structures using lightweight erectable tetrahedral truss and part-spherical truss configurations. Excellent agreement for the minimum mass was obtained with the three different aerobrake structures. Also, the minimum mass using the present structure was obtained when the supports were not at the base but at about 75 percent of the base diameter.

76 FR 56120 - Atlantic Highly Migratory Species; North and South Atlantic Swordfish Quotas

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-12

... Contracting Parties. Contracting Parties may restrict fishermen to a minimum size of 25 kg live weight OR 125... restrict fishermen to a minimum size of 15 kg live weight OR 119 cm LJFL with no tolerance. In 2009, NMFS... quota, among other things. Per the ATCA, the United States is obligated to implement ICCAT-approved...

Deeper sparsely nets are size-optimal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beiu, V.; Makaruk, H.E.

1997-12-01

The starting points of this paper are two size-optimal solutions: (i) one for implementing arbitrary Boolean functions (Horne, 1994); and (ii) another one for implementing certain sub-classes of Boolean functions (Red`kin, 1970). Because VLSI implementations do not cope well with highly interconnected nets--the area of a chip grows with the cube of the fan-in (Hammerstrom, 1988)--this paper will analyze the influence of limited fan-in on the size optimality for the two solutions mentioned. First, the authors will extend a result from Horne and Hush (1994) valid for fan-in {Delta} = 2 to arbitrary fan-in. Second, they will prove that size-optimalmore » solutions are obtained for small constant fan-in for both constructions, while relative minimum size solutions can be obtained for fan-ins strictly lower than linear. These results are in agreement with similar ones proving that for small constant fan-ins ({Delta} = 6...9) there exist VLSI-optimal (i.e. minimizing AT{sup 2}) solutions (Beiu, 1997a), while there are similar small constants relating to the capacity of processing information (Miller 1956).« less

Dominating Scale-Free Networks Using Generalized Probabilistic Methods

PubMed Central

Molnár,, F.; Derzsy, N.; Czabarka, É.; Székely, L.; Szymanski, B. K.; Korniss, G.

2014-01-01

We study ensemble-based graph-theoretical methods aiming to approximate the size of the minimum dominating set (MDS) in scale-free networks. We analyze both analytical upper bounds of dominating sets and numerical realizations for applications. We propose two novel probabilistic dominating set selection strategies that are applicable to heterogeneous networks. One of them obtains the smallest probabilistic dominating set and also outperforms the deterministic degree-ranked method. We show that a degree-dependent probabilistic selection method becomes optimal in its deterministic limit. In addition, we also find the precise limit where selecting high-degree nodes exclusively becomes inefficient for network domination. We validate our results on several real-world networks, and provide highly accurate analytical estimates for our methods. PMID:25200937

Throughput and delay analysis of IEEE 802.15.6-based CSMA/CA protocol.

PubMed

Ullah, Sana; Chen, Min; Kwak, Kyung Sup

2012-12-01

The IEEE 802.15.6 is a new communication standard on Wireless Body Area Network (WBAN) that focuses on a variety of medical, Consumer Electronics (CE) and entertainment applications. In this paper, the throughput and delay performance of the IEEE 802.15.6 is presented. Numerical formulas are derived to determine the maximum throughput and minimum delay limits of the IEEE 802.15.6 for an ideal channel with no transmission errors. These limits are derived for different frequency bands and data rates. Our analysis is validated by extensive simulations using a custom C+ + simulator. Based on analytical and simulation results, useful conclusions are derived for network provisioning and packet size optimization for different applications.

Modelling CLPX IOP3 Radiometric Data by Means of the Dense Media Theory: Preliminary Results for the LSOS Test Site

NASA Technical Reports Server (NTRS)

Tedesco, Marco; Kim, Edward J.; Cline, Don; Graf, Tobias; Koike, Toshio; Armstrong, Richard; Brodzik, Mary Jo; Hardy, Janet

2003-01-01

The capabilities of the Dense Media Radiative Transfer model using the Quasi Crystalline Approximation with Coherent Potential (QCA-CP) to reproduce measured radiometric data were tested using the University of Tokyo Ground Based Microwave Radiometer (GBMR-7) during the third Intensive Observation Period (IOP3) of the NASA Cold-land Processes Field Experiment (CLPX). The data were collected at the Local-Scale Observation Site (LSOS), a 0.8-ha study site consisting of two open meadows separated by trees. Intensive measurements were also made of snow depth and temperature, density, and grain size profiles. A DMRT model is needed to describe radiative transfer in a medium such as snow because the assumption of independent scattering used in classical radiative transfer theory (CRT) is not valid. Validation of the DMRT approach requires a relationship between measured snow grain size and the DMRT approximation of snow grain radius as spherical particles with a mean radius of the log-normal particle-size distribution. This relationship is very important for a better understanding of snow modelling and for practical applications. DMRT simulations were compared with observations of microwave brightnesses at 18.7, 36.5 and 89-GHz (V and H polarizations) collected on February-1 9-25, 2003. Observation angles ranged from 30\\deg to 70\\deg. Model inputs included measured snow parameters except mean grain size. The average snow temperature, fractional volume and depth were held constant, together with the ice and soil permittivities. The minimum and maximum measured mean grain sizes were used to test the capabilities of the DMRT to reproduce the brightnesses as upper and lower limits. The sensitivity to the largest and smallest measured grain size in the three classes of minimum, medium and maximum observed grain sizes was also investigated. DMRT particle sizes yielding a best-fit to the experimental data for each date were computed. Results show that the measured brightnesses fall within the range of simulated brightnesses using the smallest and largest measured grain size values. The DMRT best-fit radii are comparable to the average radii for the medium observed grain sizes.

7 CFR 51.344 - Size.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Standards for Grades of Apples for Processing Size § 51.344 Size. (a) The minimum and maximum sizes or range... the apples determined by the smallest opening through which it will pass. Application of Standards ...

7 CFR 51.344 - Size.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Standards for Grades of Apples for Processing Size § 51.344 Size. (a) The minimum and maximum sizes or range... the apples determined by the smallest opening through which it will pass. Application of Standards ...

7 CFR 51.344 - Size.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Standards for Grades of Apples for Processing Size § 51.344 Size. (a) The minimum and maximum sizes or range... the apples determined by the smallest opening through which it will pass. Application of Standards ...

Setting population targets for mammals using body mass as a predictor of population persistence.

PubMed

Hilbers, Jelle P; Santini, Luca; Visconti, Piero; Schipper, Aafke M; Pinto, Cecilia; Rondinini, Carlo; Huijbregts, Mark A J

2017-04-01

Conservation planning and biodiversity assessments need quantitative targets to optimize planning options and assess the adequacy of current species protection. However, targets aiming at persistence require population-specific data, which limit their use in favor of fixed and nonspecific targets, likely leading to unequal distribution of conservation efforts among species. We devised a method to derive equitable population targets; that is, quantitative targets of population size that ensure equal probabilities of persistence across a set of species and that can be easily inferred from species-specific traits. In our method, we used models of population dynamics across a range of life-history traits related to species' body mass to estimate minimum viable population targets. We applied our method to a range of body masses of mammals, from 2 g to 3825 kg. The minimum viable population targets decreased asymptotically with increasing body mass and were on the same order of magnitude as minimum viable population estimates from species- and context-specific studies. Our approach provides a compromise between pragmatic, nonspecific population targets and detailed context-specific estimates of population viability for which only limited data are available. It enables a first estimation of species-specific population targets based on a readily available trait and thus allows setting equitable targets for population persistence in large-scale and multispecies conservation assessments and planning. © 2016 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

Preparedness for epidemic disease or bioterrorism: minimum cost planning for the location and staffing of urban point-of-dispensing centers.

PubMed

Bowen, William M; Chen, Jen-Yi; Tukel, Oya I

2014-01-01

Urban health authorities in the United States have been charged with developing plans for providing the infrastructure necessary to dispense prophylactic medications to their populations in the case of epidemic disease outbreak or bioterrorist attack. However, no specific method for such plans has been prescribed. This article formulates and demonstrates the use of an integer programming technique for helping to solve a part of the dispensing problem faced by cities, namely that of providing the federally required infrastructure at minimum cost, using their limited time and resources. Specifically, the technique minimizes the number of point-of-dispensing (POD) centers while covering every resident in all the census tracts within the city's jurisdiction. It also determines the optimal staffing requirement in terms of the number of nurses at each POD. This article includes a demonstration of the model using real data from Cleveland, OH, a mid-sized US city. Examples are provided of data and computational results for a variety of input parameter values such as population throughput rate, POD capacities, and distance limitations. The technique can be readily adapted to a wide range of urban areas.

Compression of Born ratio for fluorescence molecular tomography/x-ray computed tomography hybrid imaging: methodology and in vivo validation.

PubMed

Mohajerani, Pouyan; Ntziachristos, Vasilis

2013-07-01

The 360° rotation geometry of the hybrid fluorescence molecular tomography/x-ray computed tomography modality allows for acquisition of very large datasets, which pose numerical limitations on the reconstruction. We propose a compression method that takes advantage of the correlation of the Born-normalized signal among sources in spatially formed clusters to reduce the size of system model. The proposed method has been validated using an ex vivo study and an in vivo study of a nude mouse with a subcutaneous 4T1 tumor, with and without inclusion of a priori anatomical information. Compression rates of up to two orders of magnitude with minimum distortion of reconstruction have been demonstrated, resulting in large reduction in weight matrix size and reconstruction time.

Comparing the minimum spatial-frequency content for recognizing Chinese and alphabet characters

PubMed Central

Wang, Hui; Legge, Gordon E.

2018-01-01

Visual blur is a common problem that causes difficulty in pattern recognition for normally sighted people under degraded viewing conditions (e.g., near the acuity limit, when defocused, or in fog) and also for people with impaired vision. For reliable identification, the spatial frequency content of an object needs to extend up to or exceed a minimum value in units of cycles per object, referred to as the critical spatial frequency. In this study, we investigated the critical spatial frequency for alphabet and Chinese characters, and examined the effect of pattern complexity. The stimuli were divided into seven categories based on their perimetric complexity, including the lowercase and uppercase alphabet letters, and five groups of Chinese characters. We found that the critical spatial frequency significantly increased with complexity, from 1.01 cycles per character for the simplest group to 2.00 cycles per character for the most complex group of Chinese characters. A second goal of the study was to test a space-bandwidth invariance hypothesis that would represent a tradeoff between the critical spatial frequency and the number of adjacent patterns that can be recognized at one time. We tested this hypothesis by comparing the critical spatial frequencies in cycles per character from the current study and visual-span sizes in number of characters (measured by Wang, He, & Legge, 2014) for sets of characters with different complexities. For the character size (1.2°) we used in the study, we found an invariant product of approximately 10 cycles, which may represent a capacity limitation on visual pattern recognition. PMID:29297056

Mechanical trapping of particles in granular media

NASA Astrophysics Data System (ADS)

Kerimov, Abdulla; Mavko, Gary; Mukerji, Tapan; Al Ibrahim, Mustafa A.

2018-02-01

Mechanical trapping of fine particles in the pores of granular materials is an essential mechanism in a wide variety of natural and industrial filtration processes. The progress of invading particles is primarily limited by the network of pore throats and connected pathways encountered by the particles during their motion through the porous medium. Trapping of invading particles is limited to a depth defined by the size, shape, and distribution of the invading particles with respect to the size, shape, and distribution of the host porous matrix. Therefore, the trapping process, in principle, can be used to obtain information about geometrical properties, such as pore throat and particle size, of the underlying host matrix. A numerical framework is developed to simulate the mechanical trapping of fine particles in porous granular media with prescribed host particle size, shape, and distribution. The trapping of invading particles is systematically modeled in host packings with different host particle distributions: monodisperse, bidisperse, and polydisperse distributions of host particle sizes. Our simulation results show quantitatively and qualitatively to what extent trapping behavior is different in the generated monodisperse, bidisperse, and polydisperse packings of spherical particles. Depending on host particle size and distribution, the information about extreme estimates of minimal pore throat sizes of the connected pathways in the underlying host matrix can be inferred from trapping features, such as the fraction of trapped particles as a function of invading particle size. The presence of connected pathways with minimum and maximum of minimal pore throat diameters can be directly obtained from trapping features. This limited information about the extreme estimates of pore throat sizes of the connected pathways in the host granular media inferred from our numerical simulations is consistent with simple geometrical estimates of extreme value of pore and throat sizes of the densest structural arrangements of spherical particles and geometrical Delaunay tessellation analysis of the pore space of host granular media. Our results suggest simple relations between the host particle size and trapping features. These relationships can be potentially used to describe both the dynamics of the mechanical trapping process and the geometrical properties of the host granular media.

Mechanical trapping of particles in granular media.

PubMed

Kerimov, Abdulla; Mavko, Gary; Mukerji, Tapan; Al Ibrahim, Mustafa A

2018-02-01

Mechanical trapping of fine particles in the pores of granular materials is an essential mechanism in a wide variety of natural and industrial filtration processes. The progress of invading particles is primarily limited by the network of pore throats and connected pathways encountered by the particles during their motion through the porous medium. Trapping of invading particles is limited to a depth defined by the size, shape, and distribution of the invading particles with respect to the size, shape, and distribution of the host porous matrix. Therefore, the trapping process, in principle, can be used to obtain information about geometrical properties, such as pore throat and particle size, of the underlying host matrix. A numerical framework is developed to simulate the mechanical trapping of fine particles in porous granular media with prescribed host particle size, shape, and distribution. The trapping of invading particles is systematically modeled in host packings with different host particle distributions: monodisperse, bidisperse, and polydisperse distributions of host particle sizes. Our simulation results show quantitatively and qualitatively to what extent trapping behavior is different in the generated monodisperse, bidisperse, and polydisperse packings of spherical particles. Depending on host particle size and distribution, the information about extreme estimates of minimal pore throat sizes of the connected pathways in the underlying host matrix can be inferred from trapping features, such as the fraction of trapped particles as a function of invading particle size. The presence of connected pathways with minimum and maximum of minimal pore throat diameters can be directly obtained from trapping features. This limited information about the extreme estimates of pore throat sizes of the connected pathways in the host granular media inferred from our numerical simulations is consistent with simple geometrical estimates of extreme value of pore and throat sizes of the densest structural arrangements of spherical particles and geometrical Delaunay tessellation analysis of the pore space of host granular media. Our results suggest simple relations between the host particle size and trapping features. These relationships can be potentially used to describe both the dynamics of the mechanical trapping process and the geometrical properties of the host granular media.

Plant Distribution Data Show Broader Climatic Limits than Expert-Based Climatic Tolerance Estimates

PubMed Central

Curtis, Caroline A.; Bradley, Bethany A.

2016-01-01

Background Although increasingly sophisticated environmental measures are being applied to species distributions models, the focus remains on using climatic data to provide estimates of habitat suitability. Climatic tolerance estimates based on expert knowledge are available for a wide range of plants via the USDA PLANTS database. We aim to test how climatic tolerance inferred from plant distribution records relates to tolerance estimated by experts. Further, we use this information to identify circumstances when species distributions are more likely to approximate climatic tolerance. Methods We compiled expert knowledge estimates of minimum and maximum precipitation and minimum temperature tolerance for over 1800 conservation plant species from the ‘plant characteristics’ information in the USDA PLANTS database. We derived climatic tolerance from distribution data downloaded from the Global Biodiversity and Information Facility (GBIF) and corresponding climate from WorldClim. We compared expert-derived climatic tolerance to empirical estimates to find the difference between their inferred climate niches (ΔCN), and tested whether ΔCN was influenced by growth form or range size. Results Climate niches calculated from distribution data were significantly broader than expert-based tolerance estimates (Mann-Whitney p values << 0.001). The average plant could tolerate 24 mm lower minimum precipitation, 14 mm higher maximum precipitation, and 7° C lower minimum temperatures based on distribution data relative to expert-based tolerance estimates. Species with larger ranges had greater ΔCN for minimum precipitation and minimum temperature. For maximum precipitation and minimum temperature, forbs and grasses tended to have larger ΔCN while grasses and trees had larger ΔCN for minimum precipitation. Conclusion Our results show that distribution data are consistently broader than USDA PLANTS experts’ knowledge and likely provide more robust estimates of climatic tolerance, especially for widespread forbs and grasses. These findings suggest that widely available expert-based climatic tolerance estimates underrepresent species’ fundamental niche and likely fail to capture the realized niche. PMID:27870859

7 CFR 51.2836 - Size classifications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Size classifications. 51.2836 Section 51.2836...) Size Classifications § 51.2836 Size classifications. The size of onions may be specified in accordance with one of the following classifications. Size designation Minimum diameter Inches Millimeters Maximum...

7 CFR 51.2836 - Size classifications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Size classifications. 51.2836 Section 51.2836...-Granex-Grano and Creole Types) Size Classifications § 51.2836 Size classifications. The size of onions may be specified in accordance with one of the following classifications. Size designation Minimum...

7 CFR 51.2836 - Size classifications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Size classifications. 51.2836 Section 51.2836...-Granex-Grano and Creole Types) Size Classifications § 51.2836 Size classifications. The size of onions may be specified in accordance with one of the following classifications. Size designation Minimum...

7 CFR 51.2836 - Size classifications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Size classifications. 51.2836 Section 51.2836...) Size Classifications § 51.2836 Size classifications. The size of onions may be specified in accordance with one of the following classifications. Size designation Minimum diameter Inches Millimeters Maximum...

7 CFR 51.2836 - Size classifications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Size classifications. 51.2836 Section 51.2836...) Size Classifications § 51.2836 Size classifications. The size of onions may be specified in accordance with one of the following classifications. Size designation Minimum diameter Inches Millimeters Maximum...

Population demographics and genetic diversity in remnant and translocated populations of sea otters

USGS Publications Warehouse

Bodkin, James L.; Ballachey, Brenda E.; Cronin, M.A.; Scribner, K.T.

1999-01-01

The effects of small population size on genetic diversity and subsequent population recovery are theoretically predicted, but few empirical data are available to describe those relations. We use data from four remnant and three translocated sea otter (Enhydra lutris) populations to examine relations among magnitude and duration of minimum population size, population growth rates, and genetic variation. Metochondrial (mt)DNA haplotype diversity was correlated with the number of years at minimum population size (r = -0.741, p = 0.038) and minimum population size (r = 0.709, p = 0.054). We found no relation between population growth and haplotype diversity, altough growth was significantly greater in translocated than in remnant populations. Haplotype diversity in populations established from two sources was higher than in a population established from a single source and was higher than in the respective source populations. Haplotype frequencies in translocated populations of founding sizes of 4 and 28 differed from expected, indicating genetic drift and differential reproduction between source populations, whereas haplotype frequencies in a translocated population with a founding size of 150 did not. Relations between population demographics and genetic characteristics suggest that genetic sampling of source and translocated populations can provide valuable inferences about translocations.

A Real Options Approach to Quantity and Cost Optimization for Lifetime and Bridge Buys of Parts

DTIC Science & Technology

2015-04-30

fixed EOS of 40 years and a fixed WACC of 3%, decreases to a minimum and then increases. The minimum of this curve gives the optimum buy size for...considered in both analyses. For a 3% WACC , as illustrated in Figure 9(a), the DES method gives an optimum buy size range of 2,923–3,191 with an average...Hence, both methods are consistent in determining the optimum lifetime/bridge buy size. To further verify this consistency, other WACC values

Dying piece by piece: carbohydrate dynamics in aspen (Populus tremuloides) seedlings under severe carbon stress.

PubMed

Wiley, Erin; Hoch, Günter; Landhäusser, Simon M

2017-11-02

Carbon starvation as a mechanism of tree mortality is poorly understood. We exposed seedlings of aspen (Populus tremuloides) to complete darkness at 20 or 28 °C to identify minimum non-structural carbohydrate (NSC) concentrations at which trees die and to see if these levels vary between organs or with environmental conditions. We also first grew seedlings under different shade levels to determine if size affects survival time under darkness due to changes in initial NSC concentration and pool size and/or respiration rates. Darkness treatments caused a gradual dieback of tissues. Even after half the stem had died, substantial starch reserves were still present in the roots (1.3-3% dry weight), indicating limitations to carbohydrate remobilization and/or transport during starvation in the absence of water stress. Survival time decreased with increased temperature and with increasing initial shade level, which was associated with smaller biomass, higher respiration rates, and initially smaller NSC pool size. Dead tissues generally contained no starch, but sugar concentrations were substantially above zero and differed between organs (~2% in stems up to ~7.5% in leaves) and, at times, between temperature treatments and initial, pre-darkness shade treatments. Minimum root NSC concentrations were difficult to determine because dead roots quickly began to decompose, but we identify 5-6% sugar as a potential threshold for living roots. This variability may complicate efforts to identify critical NSC thresholds below which trees starve. © Society for Experimental Biology 2017.

Case Study of the Minimum Provable Risk Considering the Variation in Background Risk: Effect of Residual Risk on Epidemiological Studies and a Comparative Assessment of Fatal Disease Risk Due to Radiation Exposure.

PubMed

Sasaki, Michiya; Ogino, Haruyuki; Hattori, Takatoshi

2018-06-08

In order to prove a small increment in a risk of concern in an epidemiological study, a large sample of a population is generally required. Since the background risk of an end point of interest, such as cancer mortality, is affected by various factors, such as lifestyle (diet, smoking, etc.), adjustment for such factors is necessary. However, it is impossible to inclusively and completely adjust for such factors; therefore, uncertainty in the background risk remains for control and exposed populations, indicating that there is a minimum limit to the lower bound for the provable risk regardless of the sample size. In this case study, we developed and discussed the minimum provable risk considering the uncertainty in background risk for hypothetical populations by referring to recent Japanese statistical information to grasp the extent of the minimum provable risk. Risk of fatal diseases due to radiation exposure, which has recently been the focus of radiological protection, was also examined by comparative assessment of the minimum provable risk for cancer and circulatory diseases. It was estimated that the minimum provable risk for circulatory disease mortality was much greater than that for cancer mortality, approximately five to seven times larger; circulatory disease mortality is more difficult to prove as a radiation risk than cancer mortality under the conditions used in this case study.This is an open-access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal.

Maturation and sexual ontogeny in the spangled emperor Lethrinus nebulosus.

PubMed

Marriott, R J; Jarvis, N D C; Adams, D J; Gallash, A E; Norriss, J; Newman, S J

2010-04-01

The reproductive development and sexual ontogeny of spangled emperor Lethrinus nebulosus populations in the Ningaloo Marine Park (NMP) were investigated to obtain an improved understanding of its evolved reproductive strategy and data for fisheries management. Evidence derived from (1) analyses of histological data and sampled sex ratios with size and age, (2) the identification of residual previtellogenic oocytes in immature and mature testes sampled during the spawning season and (3) observed changes in testis internal structure with increasing fish size and age, demonstrated a non-functional protogynous hermaphroditic strategy (or functional gonochorism). All the smallest and youngest fish sampled were female until they either changed sex to male at a mean 277.5 mm total length (L(T)) and 2.3 years old or remained female and matured at a larger mean L(T) (392.1 mm) and older age (3.5 years). Gonad masses were similar for males and females over the size range sampled and throughout long reproductive lives (up to a maximum estimated age of c. 31 years), which was another correlate of functional gonochorism. That the mean L(T) at sex change and female maturity were below the current minimum legal size (MLS) limit (410 mm) demonstrated that the current MLS limit is effective for preventing recreational fishers in the NMP retaining at least half of the juvenile males and females in their landed catches.

Quantitative Research on the Minimum Wage

ERIC Educational Resources Information Center

Goldfarb, Robert S.

1975-01-01

The article reviews recent research examining the impact of minimum wage requirements on the size and distribution of teenage employment and earnings. The studies measure income distribution, employment levels and effect on unemployment. (MW)

Large space deployable antenna systems

NASA Technical Reports Server (NTRS)

1978-01-01

The design technology is described for manufacturing a 20 m or larger space erectable antenna with high thermal stability, high dynamic stiffness, and minimum stowed size. The selected approach includes a wrap rib design with a cantilever beam basic element and graphite-epoxy composite lenticular cross section ribs. The rib configuration and powered type operated deploying mechanism are described and illustrated. Other features of the parabolic reflector discussed include weight and stowed diameter characteristics, structural dynamics characteristics, orbit thermal aperture limitations, and equivalent element and secondary (on axis) patterns. A block diagram of the multiple beam pattern is also presented.

Regenerable non-venting thermal control subsystem for extravehicular activity

NASA Technical Reports Server (NTRS)

Roebelen, George J.; Bayes, Stephen A.; Lawson, B. Mike

1986-01-01

Routine and complex EVAs call for more effective heat rejection systems in order to maximize mission productivity; an optimum EVA mobility unit (EMU) thermal control subsystem must require no expendables and introduce no contaminants into the environment, while conforming to minimum size limits and allowing easy regeneration. Attention is presently given to two thermal control subsystems, one of which can be integrated with the existing Space Shuttle Orbiter EMU to provide a 3-hour nonventing heat rejection capability, while the other can furnish the entire heat rejection capability requirement for an 8-hour Space Station EVA.

7 CFR 51.3198 - Size classifications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Size classifications. 51.3198 Section 51.3198... STANDARDS) United States Standards for Grades of Bermuda-Granex-Grano Type Onions Size Classifications § 51.3198 Size classifications. Size shall be specified in connection with the grade in terms of minimum...

7 CFR 51.3198 - Size classifications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Size classifications. 51.3198 Section 51.3198... STANDARDS) United States Standards for Grades of Bermuda-Granex-Grano Type Onions Size Classifications § 51.3198 Size classifications. Size shall be specified in connection with the grade in terms of minimum...

7 CFR 51.3198 - Size classifications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Size classifications. 51.3198 Section 51.3198... STANDARDS) United States Standards for Grades of Bermuda-Granex-Grano Type Onions Size Classifications § 51.3198 Size classifications. Size shall be specified in connection with the grade in terms of minimum...

Impact of minimum catch size on the population viability of Strombus gigas (Mesogastropoda: Strombidae) in Quintana Roo, Mexico.

PubMed

Peel, Joanne R; Mandujano, María del Carmen

2014-12-01

The queen conch Strombus gigas represents one of the most important fishery resources of the Caribbean but heavy fishing pressure has led to the depletion of stocks throughout the region, causing the inclusion of this species into CITES Appendix II and IUCN's Red-List. In Mexico, the queen conch is managed through a minimum fishing size of 200 mm shell length and a fishing quota which usually represents 50% of the adult biomass. The objectives of this study were to determine the intrinsic population growth rate of the queen conch population of Xel-Ha, Quintana Roo, Mexico, and to assess the effects of a regulated fishing impact, simulating the extraction of 50% adult biomass on the population density. We used three different minimum size criteria to demonstrate the effects of minimum catch size on the population density and discuss biological implications. Demographic data was obtained through capture-mark-recapture sampling, collecting all animals encountered during three hours, by three divers, at four different sampling sites of the Xel-Ha inlet. The conch population was sampled each month between 2005 and 2006, and bimonthly between 2006 and 2011, tagging a total of 8,292 animals. Shell length and lip thickness were determined for each individual. The average shell length for conch with formed lip in Xel-Ha was 209.39 ± 14.18 mm and the median 210 mm. Half of the sampled conch with lip ranged between 200 mm and 219 mm shell length. Assuming that the presence of the lip is an indicator for sexual maturity, it can be concluded that many animals may form their lip at greater shell lengths than 200 mm and ought to be considered immature. Estimation of relative adult abundance and densities varied greatly depending on the criteria employed for adult classification. When using a minimum fishing size of 200 mm shell length, between 26.2% and up to 54.8% of the population qualified as adults, which represented a simulated fishing impact of almost one third of the population. When conch extraction was simulated using a classification criteria based on lip thickness, it had a much smaller impact on the population density. We concluded that the best management strategy for S. gigas is a minimum fishing size based on a lip thickness, since it has lower impact on the population density, and given that selective fishing pressure based on size may lead to the appearance of small adult individuals with reduced fecundity. Furthermore, based on the reproductive biology and the results of the simulated fishing, we suggest a minimum lip thickness of ≥ 15 mm, which ensures the protection of reproductive stages, reduces the risk of overfishing, leading to non-viable density reduction.

Estimation of representative elementary volume for DNAPL saturation and DNAPL-water interfacial areas in 2D heterogeneous porous media

NASA Astrophysics Data System (ADS)

Wu, Ming; Cheng, Zhou; Wu, Jianfeng; Wu, Jichun

2017-06-01

Representative elementary volume (REV) is important to determine properties of porous media and those involved in migration of contaminants especially dense nonaqueous phase liquids (DNAPLs) in subsurface environment. In this study, an experiment of long-term migration of the commonly used DNAPL, perchloroethylene (PCE), is performed in a two dimensional (2D) sandbox where several system variables including porosity, PCE saturation (Soil) and PCE-water interfacial area (AOW) are accurately quantified by light transmission techniques over the entire PCE migration process. Moreover, the REVs for these system variables are estimated by a criterion of relative gradient error (εgi) and results indicate that the frequency of minimum porosity-REV size closely follows a Gaussian distribution in the range of 2.0 mm and 8.0 mm. As experiment proceeds in PCE infiltration process, the frequency and cumulative frequency of both minimum Soil-REV and minimum AOW-REV sizes change their shapes from the irregular and random to the regular and smooth. When experiment comes into redistribution process, the cumulative frequency of minimum Soil-REV size reveals a linear positive correlation, while frequency of minimum AOW-REV size tends to a Gaussian distribution in the range of 2.0 mm-7.0 mm and appears a peak value in 13.0 mm-14.0 mm. Undoubtedly, this study will facilitate the quantification of REVs for materials and fluid properties in a rapid, handy and economical manner, which helps enhance our understanding of porous media and DNAPL properties at micro scale, as well as the accuracy of DNAPL contamination modeling at field-scale.

Deeper and sparser nets are optimal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beiu, V.; Makaruk, H.E.

1998-03-01

The starting points of this paper are two size-optimal solutions: (1) one for implementing arbitrary Boolean functions (Home and Hush, 1994); and (2) another one for implementing certain sub-classes of Boolean functions (Red`kin, 1970). Because VLSI implementations do not cope well with highly interconnected nets--the area of a chip grows with the cube of the fan-in (Hammerstrom, 1988)--this paper will analyze the influence of limited fan-in on the size optimality for the two solutions mentioned. First, the authors will extend a result from Home and Hush (1994) valid for fan-in {Delta} = 2 to arbitrary fan-in. Second, they will provemore » that size-optimal solutions are obtained for small constant fan-in for both constructions, while relative minimum size solutions can be obtained for fan-ins strictly lower that linear. These results are in agreement with similar ones proving that for small constant fan-ins ({Delta} = 6...9) there exist VLSI-optimal (i.e., minimizing AT{sup 2}) solutions (Beiu, 1997a), while there are similar small constants relating to the capacity of processing information (Miller 1956).« less

Surfactants-aided syntheses of different sizes and triangular shape of gold nanoparticles using trisodium citrate in environmentally friendly and photoinduced methods.

PubMed

Su, Yen Hsun; Lai, Wei Hao; Chang, Shih-Hui; Hon, Min Hsiung

2007-09-01

We prepared gold nanoparticles (Au NPs) by only using trisodium citrate as the stabilizer. The detailed reaction mechanisms of S(N)1 and E1 reactions are examined and evidenced in this study by FTIR data. Citric acid is a kind of tertiary substrate. In aqueous solution, the substitution nucleophile path 1 (S(N)1) reaction and Elimination path 1 (E1) reaction usually occur simultaneously. Chloride ions, the substitution nucleophile, play a very important role to launch the mechanisms of S(N)1 and E1 reactions. Controlling the concentration of the chloride ions with the addition of HCl(aq) according to Le Chatelier theory, the average particle size of Au NPs (5.5 nm) was achieved to overcome the minimum limited size (approximately 10 nm). Two stages of the photoinduced method, aggregation into triangular conglomerates and growth into triangular particles, were determined form TEM observations. This preparation of Au NPs has potential in tuning the size, shape, and mechanism of Au NP formation by using only environmentally friendly trisodium citrate and the photoinduced method.

Evaluation of AQUI-S(TM) (efficacy and minimum toxic concentration) as a fish anaesthetic/sedative for public aquaculture in the United States

USGS Publications Warehouse

Stehly, G.R.; Gingerich, W.H.

1999-01-01

A preliminary evaluation of efficacy and minimum toxic concentration of AQUI-S(TM), a fish anaesthetic/sedative, was determined in two size classes of six species of fish important to US public aquaculture (bluegill, channel catfish, lake trout, rainbow trout, walleye and yellow perch). In addition, efficacy and minimum toxic concentration were determined in juvenile-young adult (fish aged 1 year or older) rainbow trout acclimated to water at 7 ??C, 12 ??C and 17 ??C. Testing concentrations were based on determinations made with range-finding studies for both efficacy and minimum toxic concentration. Most of the tested juvenile-young adult fish species were induced in 3 min or less at a nominal AQUI-S(TM) concentration of 20 mg L-1. In juvenile-young adult fish, the minimum toxic concentration was at least 2.5 times the selected efficacious concentration. Three out of five species of fry-fingerlings (1.25-12.5 cm in length and < 1 year old) were induced in ??? 4.1 min at a nominal concentration of 20 mg L-1 AQUI-S(TM), with the other two species requiring nominal concentrations of 25 and 35 mg L-1 for similar times of induction. Recovery times were ??? 7.3 rain for all species in the two size classes. In fry-fingerlings, the minimum toxic concentration was at least 1.4 times the selected efficacious concentration. There appeared to be little relationship between size of fish and concentrations or times to induction, recovery times and minimum toxic concentration. The times required for induction and for recovery were increased in rainbow trout as the acclimation temperature was reduced.

Climate and topography explain range sizes of terrestrial vertebrates

NASA Astrophysics Data System (ADS)

Li, Yiming; Li, Xianping; Sandel, Brody; Blank, David; Liu, Zetian; Liu, Xuan; Yan, Shaofei

2016-05-01

Identifying the factors that influence range sizes of species provides important insight into the distribution of biodiversity, and is crucial for predicting shifts in species ranges in response to climate change. Current climate (for example, climate variability and climate extremes), long-term climate change, evolutionary age, topographic heterogeneity, land area and species traits such as physiological thermal limits, dispersal ability, annual fecundity and body size have been shown to influence range size. Yet, few studies have examined the generality of each of these factors among different taxa, or have simultaneously evaluated the strength of relationships between range size and these factors at a global scale. We quantify contributions of these factors to range sizes of terrestrial vertebrates (mammals, birds and reptiles) at a global scale. We found that large-ranged species experience greater monthly extremes of maximum or minimum temperature within their ranges, or occur in areas with higher long-term climate velocity and lower topographic heterogeneity or lower precipitation seasonality. Flight ability, body mass and continent width are important only for particular taxa. Our results highlight the importance of climate and topographic context in driving range size variation. The results suggest that small-range species may be vulnerable to climate change and should be the focus of conservation efforts.

Computational analysis of particle reinforced viscoelastic polymer nanocomposites - statistical study of representative volume element

NASA Astrophysics Data System (ADS)

Hu, Anqi; Li, Xiaolin; Ajdari, Amin; Jiang, Bing; Burkhart, Craig; Chen, Wei; Brinson, L. Catherine

2018-05-01

The concept of representative volume element (RVE) is widely used to determine the effective material properties of random heterogeneous materials. In the present work, the RVE is investigated for the viscoelastic response of particle-reinforced polymer nanocomposites in the frequency domain. The smallest RVE size and the minimum number of realizations at a given volume size for both structural and mechanical properties are determined for a given precision using the concept of margin of error. It is concluded that using the mean of many realizations of a small RVE instead of a single large RVE can retain the desired precision of a result with much lower computational cost (up to three orders of magnitude reduced computation time) for the property of interest. Both the smallest RVE size and the minimum number of realizations for a microstructure with higher volume fraction (VF) are larger compared to those of one with lower VF at the same desired precision. Similarly, a clustered structure is shown to require a larger minimum RVE size as well as a larger number of realizations at a given volume size compared to the well-dispersed microstructures.

Droplet size effects on NO/x/ formation in a one-dimensional monodisperse spray combustion system

NASA Technical Reports Server (NTRS)

Sarv, H.; Nizami, A. A.; Cernansky, N. P.

1982-01-01

A one-dimensional monodisperse aerosol spray combustion facility is described and experimental results of post flame NO/NO(x) emissions are presented. Four different hydrocarbon fuels were studied: isopropanol, methanol, n-heptane, and n-octane. The results indicate an optimum droplet size in the range of 48-58 microns for minimizing NO/NO(x) production for all of the test fuels. This NO(x) behavior is associated with droplet interactions and the transition from diffusive type of spray burning to that of a prevaporized and premixed case. Decreasing the droplet size results in a trend of increasing droplet interactions, which suppresses temperatures and reduces NO(x). This trend continues until prevaporization effects begin to dominate and the system tends towards the premixed limit. The occurrence of the minimum NO(x) point at different droplet diameters for the different fuels appears to be governed by the extent of prevaporization of the fuel in the spray, and is consistent with theoretical calculations based on each fuel's physical properties.

Optimizing the Timing Resolution for the NEXT Array

NASA Astrophysics Data System (ADS)

Engelhardt, A.; Shadrick, S.; Rajabali, M.; Schmitt, K.; Grzywacz, R.

2016-09-01

In nuclear physics studies there are very few detectors capable of measuring neutron energies in the 0.1-10 MeV energy range with a reasonable resolution. The VANDLE array is the premier detector array for these measurements, yet VANDLE is limited by the its thickness (2.9 cm minimum).The Neutron dEtector with Tracking (NEXT) array would be capable of surpassing the limitations caused by the large size of VANDLE bars. A proposed configuration of each neutron detector consists of ten 3-mm thick plastic scintillators with two or more silicon photomultipliers (SiPMs) attached at each end. To achieve the desired energy resolution for neutron energy measurements through time of flight, the timing resolution between these SiPMs needs to be below 200 ps. A SiPM was placed on each end of a plastic scintillator inside a light-tight electrical box along with a 137Cs source. An analog circuit was designed in order to measure the timing difference between the two SiPMs. Different configurations of SiPM sizes, scintillator sizes, and wrappings were tested in order to determine the configuration that yields the best timing resolution. Details of the testing procedures and results will be presented. Research Supported by the National Nuclear Security Administration.

Ensemble Weight Enumerators for Protograph LDPC Codes

NASA Technical Reports Server (NTRS)

Divsalar, Dariush

2006-01-01

Recently LDPC codes with projected graph, or protograph structures have been proposed. In this paper, finite length ensemble weight enumerators for LDPC codes with protograph structures are obtained. Asymptotic results are derived as the block size goes to infinity. In particular we are interested in obtaining ensemble average weight enumerators for protograph LDPC codes which have minimum distance that grows linearly with block size. As with irregular ensembles, linear minimum distance property is sensitive to the proportion of degree-2 variable nodes. In this paper the derived results on ensemble weight enumerators show that linear minimum distance condition on degree distribution of unstructured irregular LDPC codes is a sufficient but not a necessary condition for protograph LDPC codes.

Cavitation transition in the energy landscape: Distinct tensile yielding behavior in strongly and weakly attractive systems.

PubMed

Altabet, Y Elia; Fenley, Andreia L; Stillinger, Frank H; Debenedetti, Pablo G

2018-03-21

Particles with cohesive interactions display a tensile instability in the energy landscape at the Sastry density ρ S . The signature of this tensile limit is a minimum in the landscape equation of state, the pressure-density relationship of inherent structures sampled along a liquid isotherm. Our previous work [Y. E. Altabet, F. H. Stillinger, and P. G. Debenedetti, J. Chem. Phys. 145, 211905 (2016)] revisited the phenomenology of Sastry behavior and found that the evolution of the landscape equation of state with system size for particles with interactions typical of molecular liquids indicates the presence of an athermal first-order phase transition between homogeneous and fractured inherent structures, the latter containing several large voids. Here, we study how this tensile limit manifests itself for different interparticle cohesive strengths and identify two distinct regimes. Particles with sufficiently strong cohesion display an athermal first-order phase transition, consistent with our prior characterization. Weak cohesion also displays a tensile instability. However, the landscape equation of state for this regime is independent of system size, suggesting the absence of a first-order phase transition. An analysis of the voids suggests that yielding in the energy landscape of weakly cohesive systems is associated with the emergence of a highly interconnected network of small voids. While strongly cohesive systems transition from exclusively homogeneous to exclusively fractured configurations at ρ S in the thermodynamic limit, this interconnected network develops gradually, starting at ρ S , even at infinite system size.

Cavitation transition in the energy landscape: Distinct tensile yielding behavior in strongly and weakly attractive systems

NASA Astrophysics Data System (ADS)

Altabet, Y. Elia; Fenley, Andreia L.; Stillinger, Frank H.; Debenedetti, Pablo G.

2018-03-01

Particles with cohesive interactions display a tensile instability in the energy landscape at the Sastry density ρS. The signature of this tensile limit is a minimum in the landscape equation of state, the pressure-density relationship of inherent structures sampled along a liquid isotherm. Our previous work [Y. E. Altabet, F. H. Stillinger, and P. G. Debenedetti, J. Chem. Phys. 145, 211905 (2016)] revisited the phenomenology of Sastry behavior and found that the evolution of the landscape equation of state with system size for particles with interactions typical of molecular liquids indicates the presence of an athermal first-order phase transition between homogeneous and fractured inherent structures, the latter containing several large voids. Here, we study how this tensile limit manifests itself for different interparticle cohesive strengths and identify two distinct regimes. Particles with sufficiently strong cohesion display an athermal first-order phase transition, consistent with our prior characterization. Weak cohesion also displays a tensile instability. However, the landscape equation of state for this regime is independent of system size, suggesting the absence of a first-order phase transition. An analysis of the voids suggests that yielding in the energy landscape of weakly cohesive systems is associated with the emergence of a highly interconnected network of small voids. While strongly cohesive systems transition from exclusively homogeneous to exclusively fractured configurations at ρS in the thermodynamic limit, this interconnected network develops gradually, starting at ρS, even at infinite system size.

Effect of power system technology and mission requirements on high altitude long endurance aircraft

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.

1994-01-01

An analysis was performed to determine how various power system components and mission requirements affect the sizing of a solar powered long endurance aircraft. The aircraft power system consists of photovoltaic cells and a regenerative fuel cell. Various characteristics of these components, such as PV cell type, PV cell mass, PV cell efficiency, fuel cell efficiency, and fuel cell specific mass, were varied to determine what effect they had on the aircraft sizing for a given mission. Mission parameters, such as time of year, flight altitude, flight latitude, and payload mass and power, were also altered to determine how mission constraints affect the aircraft sizing. An aircraft analysis method which determines the aircraft configuration, aspect ratio, wing area, and total mass, for maximum endurance or minimum required power based on the stated power system and mission parameters is presented. The results indicate that, for the power system, the greatest benefit can be gained by increasing the fuel cell specific energy. Mission requirements also substantially affect the aircraft size. By limiting the time of year the aircraft is required to fly at high northern or southern latitudes, a significant reduction in aircraft size or increase in payload capacity can be achieved.

Memory performance in abstinent 3,4-methylenedioxymethamphetamine (MDMA, "ecstasy") users.

PubMed

Groth-Marnat, Gary; Howchar, Hennedy; Marsh, Ali

2007-02-01

Research with animals and humans has suggested that acute and subacute use of 3,4-methylenedioxymethamphetamine (MDMA "ecstasy") may lead to memory impairment. However, research is limited by (1) low power due to small sample sizes, (2) the possible confound of polydrug use, and (3) the failure to consider intelligence as a covariate. The present study compared the memory performance on the Wechsler Memory Scale-III of 26 abstinent (2-wk. minimum) recreational MDMA users with 26 abstinent (2-wk. minimum) recreational polydrug users. Despite significantly greater polydrug use amongst these MDMA users, no significant group differences in memory were observed. Regression of total lifetime amount of MDMA use also did not predict memory performance after accounting for intelligence. In addition, the length of time since abstinence (at least 2 wk.) was not associated with an increase in memory performance. Greater total lifetime cocaine use, rather than total lifetime MDMA use, was significantly associated with greater decrements in General Memory and Delayed Verbal Memory performance.

46 CFR 76.10-90 - Installations contracted for prior to May 26, 1965.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Not over Minimum number of pumps Minimum hose and hydrant size, inches Nozzle orifice size, inches Length of hose, feet 100 4,000 2 1 11/2 1 5/8 1 50 4,000 3 1 11/2 1 5/8 1 50 1 May use 50 feet of 21/2-inch hose with 7/8-inch nozzles for exterior stations. May use 75 feet of 11/2-inch hose with 5/8-inch...

Covariance Based Pre-Filters and Screening Criteria for Conjunction Analysis

NASA Astrophysics Data System (ADS)

George, E., Chan, K.

2012-09-01

Several relationships are developed relating object size, initial covariance and range at closest approach to probability of collision. These relationships address the following questions: - Given the objects' initial covariance and combined hard body size, what is the maximum possible value of the probability of collision (Pc)? - Given the objects' initial covariance, what is the maximum combined hard body radius for which the probability of collision does not exceed the tolerance limit? - Given the objects' initial covariance and the combined hard body radius, what is the minimum miss distance for which the probability of collision does not exceed the tolerance limit? - Given the objects' initial covariance and the miss distance, what is the maximum combined hard body radius for which the probability of collision does not exceed the tolerance limit? The first relationship above allows the elimination of object pairs from conjunction analysis (CA) on the basis of the initial covariance and hard-body sizes of the objects. The application of this pre-filter to present day catalogs with estimated covariance results in the elimination of approximately 35% of object pairs as unable to ever conjunct with a probability of collision exceeding 1x10-6. Because Pc is directly proportional to object size and inversely proportional to covariance size, this pre-filter will have a significantly larger impact on future catalogs, which are expected to contain a much larger fraction of small debris tracked only by a limited subset of available sensors. This relationship also provides a mathematically rigorous basis for eliminating objects from analysis entirely based on element set age or quality - a practice commonly done by rough rules of thumb today. Further, these relations can be used to determine the required geometric screening radius for all objects. This analysis reveals the screening volumes for small objects are much larger than needed, while the screening volumes for pairs of large objects may be inadequate. These relationships may also form the basis of an important metric for catalog maintenance by defining the maximum allowable covariance size for effective conjunction analysis. The application of these techniques promises to greatly improve the efficiency and completeness of conjunction analysis.

Evaluation of alternative model selection criteria in the analysis of unimodal response curves using CART

USGS Publications Warehouse

Ribic, C.A.; Miller, T.W.

1998-01-01

We investigated CART performance with a unimodal response curve for one continuous response and four continuous explanatory variables, where two variables were important (ie directly related to the response) and the other two were not. We explored performance under three relationship strengths and two explanatory variable conditions: equal importance and one variable four times as important as the other. We compared CART variable selection performance using three tree-selection rules ('minimum risk', 'minimum risk complexity', 'one standard error') to stepwise polynomial ordinary least squares (OLS) under four sample size conditions. The one-standard-error and minimum-risk-complexity methods performed about as well as stepwise OLS with large sample sizes when the relationship was strong. With weaker relationships, equally important explanatory variables and larger sample sizes, the one-standard-error and minimum-risk-complexity rules performed better than stepwise OLS. With weaker relationships and explanatory variables of unequal importance, tree-structured methods did not perform as well as stepwise OLS. Comparing performance within tree-structured methods, with a strong relationship and equally important explanatory variables, the one-standard-error-rule was more likely to choose the correct model than were the other tree-selection rules 1) with weaker relationships and equally important explanatory variables; and 2) under all relationship strengths when explanatory variables were of unequal importance and sample sizes were lower.

Transverse micro-erosion meter measurements; determining minimum sample size

NASA Astrophysics Data System (ADS)

Trenhaile, Alan S.; Lakhan, V. Chris

2011-11-01

Two transverse micro-erosion meter (TMEM) stations were installed in each of four rock slabs, a slate/shale, basalt, phyllite/schist, and sandstone. One station was sprayed each day with fresh water and the other with a synthetic sea water solution (salt water). To record changes in surface elevation (usually downwearing but with some swelling), 100 measurements (the pilot survey), the maximum for the TMEM used in this study, were made at each station in February 2010, and then at two-monthly intervals until February 2011. The data were normalized using Box-Cox transformations and analyzed to determine the minimum number of measurements needed to obtain station means that fall within a range of confidence limits of the population means, and the means of the pilot survey. The effect on the confidence limits of reducing an already small number of measurements (say 15 or less) is much greater than that of reducing a much larger number of measurements (say more than 50) by the same amount. There was a tendency for the number of measurements, for the same confidence limits, to increase with the rate of downwearing, although it was also dependent on whether the surface was treated with fresh or salt water. About 10 measurements often provided fairly reasonable estimates of rates of surface change but with fairly high percentage confidence intervals in slowly eroding rocks; however, many more measurements were generally needed to derive means within 10% of the population means. The results were tabulated and graphed to provide an indication of the approximate number of measurements required for given confidence limits, and the confidence limits that might be attained for a given number of measurements.

14 CFR 25.1523 - Minimum flight crew.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Minimum flight crew. 25.1523 Section 25.1523 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Limitations § 25.1523 Minimum flight crew. The minimum flight crew must be established so that it is...

14 CFR 29.1523 - Minimum flight crew.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Minimum flight crew. 29.1523 Section 29.1523 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Limitations § 29.1523 Minimum flight crew. The minimum flight crew must be established so that it is...

Retinal thinning after internal limiting membrane peeling for idiopathic macular hole.

PubMed

Imamura, Yutaka; Ishida, Masahiro

2018-03-01

To determine the changes in retinal thickness and whether they correlate with the size of the macular hole (MH) after vitrectomy with internal limiting membrane peeling. Retrospective, interventional case series METHODS: Consecutive patients with an MH and undergoing pars plana vitrectomy with internal limiting membrane peeling were studied. The retinal thicknesses in the inner 4 sectors as defined by the Early Treatment of Diabetic Retinopathy Study were measured using spectral-domain optical coherence tomography (SD-OCT) before and at 2 weeks and 1, 3, 6, and 12 months after the surgery. The basal and minimum diameters of the MHs were measured. The correlations between the retinal thicknesses and the size of the MH were determined. Thirty-three eyes of 32 consecutive patients (18 women; mean age, 64.2 ± 8.8 years) with an MH were studied. Thirteen eyes had a stage-2 MH; 12 eyes, a stage-3 MH; and 8 eyes, a stage-4 MH. The mean retinal thickness in the temporal sector was 362.8 ± 29.9 µm preoperatively, 337.9 ± 20.6 µm at 2 weeks postoperatively, and 307.6 ± 20.2 µm at 12 months postoperatively (P < .001 for both, paired t tests). The respective mean thicknesses in the superior, inferior, and nasal sectors were 373.9 ± 34.9, 367 ± 28.7, and 385.5 ± 35.9 µm preoperatively; 361.6 ± 22.7, 359.4 ± 20.6, and 383.4 ± 29.0 µm at 2 weeks postoperatively (P = .0087, P = .049, P = .635); and 339.4 ± 18.9, 331.6 ± 21.4, and 371.3 ± 23.2 µm at 12 months postoperatively (P < .001, P < .001, P = .033). The changes in the retinal thickness at 2 weeks and 12 months in all 4 sectors were significantly correlated with the basal and minimum diameters of the MH. Retinal thinning was observed soon after the MH surgery mainly in the temporal sector but also in the superior and inferior sectors. The thinning was greater in eyes with a larger MH, indicating that retinal structures dynamically change after internal limiting membrane peeling.

Protograph based LDPC codes with minimum distance linearly growing with block size

NASA Technical Reports Server (NTRS)

Divsalar, Dariush; Jones, Christopher; Dolinar, Sam; Thorpe, Jeremy

2005-01-01

We propose several LDPC code constructions that simultaneously achieve good threshold and error floor performance. Minimum distance is shown to grow linearly with block size (similar to regular codes of variable degree at least 3) by considering ensemble average weight enumerators. Our constructions are based on projected graph, or protograph, structures that support high-speed decoder implementations. As with irregular ensembles, our constructions are sensitive to the proportion of degree-2 variable nodes. A code with too few such nodes tends to have an iterative decoding threshold that is far from the capacity threshold. A code with too many such nodes tends to not exhibit a minimum distance that grows linearly in block length. In this paper we also show that precoding can be used to lower the threshold of regular LDPC codes. The decoding thresholds of the proposed codes, which have linearly increasing minimum distance in block size, outperform that of regular LDPC codes. Furthermore, a family of low to high rate codes, with thresholds that adhere closely to their respective channel capacity thresholds, is presented. Simulation results for a few example codes show that the proposed codes have low error floors as well as good threshold SNFt performance.

Determination of Minimum Training Sample Size for Microarray-Based Cancer Outcome Prediction–An Empirical Assessment

PubMed Central

Cheng, Ningtao; Wu, Leihong; Cheng, Yiyu

2013-01-01

The promise of microarray technology in providing prediction classifiers for cancer outcome estimation has been confirmed by a number of demonstrable successes. However, the reliability of prediction results relies heavily on the accuracy of statistical parameters involved in classifiers. It cannot be reliably estimated with only a small number of training samples. Therefore, it is of vital importance to determine the minimum number of training samples and to ensure the clinical value of microarrays in cancer outcome prediction. We evaluated the impact of training sample size on model performance extensively based on 3 large-scale cancer microarray datasets provided by the second phase of MicroArray Quality Control project (MAQC-II). An SSNR-based (scale of signal-to-noise ratio) protocol was proposed in this study for minimum training sample size determination. External validation results based on another 3 cancer datasets confirmed that the SSNR-based approach could not only determine the minimum number of training samples efficiently, but also provide a valuable strategy for estimating the underlying performance of classifiers in advance. Once translated into clinical routine applications, the SSNR-based protocol would provide great convenience in microarray-based cancer outcome prediction in improving classifier reliability. PMID:23861920

Application of the Maximum Amplitude-Early Rise Correlation to Cycle 23

NASA Technical Reports Server (NTRS)

Willson, Robert M.; Hathaway, David H.

2004-01-01

On the basis of the maximum amplitude-early rise correlation, cycle 23 could have been predicted to be about the size of the mean cycle as early as 12 mo following cycle minimum. Indeed, estimates for the size of cycle 23 throughout its rise consistently suggested a maximum amplitude that would not differ appreciably from the mean cycle, contrary to predictions based on precursor information. Because cycle 23 s average slope during the rising portion of the solar cycle measured 2.4, computed as the difference between the conventional maximum (120.8) and minimum (8) amplitudes divided by the ascent duration in months (47), statistically speaking, it should be a cycle of shorter period. Hence, conventional sunspot minimum for cycle 24 should occur before December 2006, probably near July 2006 (+/-4 mo). However, if cycle 23 proves to be a statistical outlier, then conventional sunspot minimum for cycle 24 would be delayed until after July 2007, probably near December 2007 (+/-4 mo). In anticipation of cycle 24, a chart and table are provided for easy monitoring of the nearness and size of its maximum amplitude once onset has occurred (with respect to the mean cycle and using the updated maximum amplitude-early rise relationship).

No support for Heincke's law in hagfish (Myxinidae): lack of an association between body size and the depth of species occurrence.

PubMed

Schumacher, E L; Owens, B D; Uyeno, T A; Clark, A J; Reece, J S

2017-08-01

This study tests for interspecific evidence of Heincke's law among hagfishes and advances the field of research on body size and depth of occurrence in fishes by including a phylogenetic correction and by examining depth in four ways: maximum depth, minimum depth, mean depth of recorded specimens and the average of maximum and minimum depths of occurrence. Results yield no evidence for Heincke's law in hagfishes, no phylogenetic signal for the depth at which species occur, but moderate to weak phylogenetic signal for body size, suggesting that phylogeny may play a role in determining body size in this group. © 2017 The Fisheries Society of the British Isles.

14 CFR 25.1513 - Minimum control speed.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Minimum control speed. 25.1513 Section 25.1513 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Limitations § 25.1513 Minimum control speed. The minimum control speed V MC determined under § 25.149 must be...

14 CFR 25.1513 - Minimum control speed.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Minimum control speed. 25.1513 Section 25.1513 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Limitations § 25.1513 Minimum control speed. The minimum control speed V MC determined under § 25.149 must be...

The Effects of Oxygen Concentration on Benthic Foraminiferal Growth and Size

NASA Astrophysics Data System (ADS)

Ng, B.; Keating-Bitonti, C.; Payne, J.

2015-12-01

Many organisms use oxygen through cellular respiration in order to gain energy. For this reason, oxygen has a significant influence on organism size and growth. The amount of oxygen an organism needs depends on its metabolic demand, which is partially a function organism size (i.e., mass). The Santa Monica Basin (SMB) is an oxygen minimum zone located off the southern coast of California that maintains a steep oxygen gradient and is thus an ideal location for conducting research on how oxygen influences organism size. Here we use benthic foraminifera, widespread single-celled protists that produce shells (tests), to study the controls of oxygen on organism size. Because cell mass and cell volume are correlated, we study trends in the log test volume of four abundant species from SMB: Uvigerina peregrina, Bolivina spissa, B. argentea, Loxostomum pseudobeyrichi. These foraminifera make multi-chambered tests, thus we also count the number of chambers per specimen in order to further assess their growth under varying oxygen concentrations. We analyzed the data using quantile regressions to determine trends in not only median values of the log test volume and number of chambers as a function of oxygen concentrations, but also in the 10th, 25th, 75th, and 90th percentiles because oxygen availability often constrains the maximum and minimum size of organisms. Our results show a positive correlation between oxygen concentration and the maximum log test volumes of L. pseudobeyrichi and B. argentea, supporting our hypothesis. However, we observed a negative correlation between oxygen concentration and the maximum percentiles of log test volume in U. peregrina. Nevertheless, U. peregrina still displays a positive correlation between chamber number and oxygen concentrations in line with our hypothesis. The preponderance of trends supporting a direct correlation between log test volume or chamber number and oxygen concentration suggest that oxygen limits the maximum obtainable size of benthic foraminifera through its effects on test volume or chamber growth. This study is important because it holds a glimpse into how changes in oxygen levels can affect organisms given current fluctuations in oxygen level around the world due to man-made climate change.

Two-point method uncertainty during control and measurement of cylindrical element diameters

NASA Astrophysics Data System (ADS)

Glukhov, V. I.; Shalay, V. V.; Radev, H.

2018-04-01

The topic of the article is devoted to the urgent problem of the reliability of technical products geometric specifications measurements. The purpose of the article is to improve the quality of parts linear sizes control by the two-point measurement method. The article task is to investigate methodical extended uncertainties in measuring cylindrical element linear sizes. The investigation method is a geometric modeling of the element surfaces shape and location deviations in a rectangular coordinate system. The studies were carried out for elements of various service use, taking into account their informativeness, corresponding to the kinematic pairs classes in theoretical mechanics and the number of constrained degrees of freedom in the datum element function. Cylindrical elements with informativity of 4, 2, 1 and θ (zero) were investigated. The uncertainties estimation of in two-point measurements was made by comparing the results of of linear dimensions measurements with the functional diameters maximum and minimum of the element material. Methodical uncertainty is formed when cylindrical elements with maximum informativeness have shape deviations of the cut and the curvature types. Methodical uncertainty is formed by measuring the element average size for all types of shape deviations. The two-point measurement method cannot take into account the location deviations of a dimensional element, so its use for elements with informativeness less than the maximum creates unacceptable methodical uncertainties in measurements of the maximum, minimum and medium linear dimensions. Similar methodical uncertainties also exist in the arbitration control of the linear dimensions of the cylindrical elements by limiting two-point gauges.

Morphology of the Physiological Apical Foramen in Maxillary and Mandibular First Molars

PubMed Central

Abarca, J.; Zaror, C.; Monardes, H.; Hermosilla, V.; Muñoz, C.; Cantin, M.

2015-01-01

SUMMARY Information regarding the anatomy of the physiological apical foramen is limited. Knowing its diameter and shapes contributes to clinical work, specifically to the cleaning and shaping of the apical third. The aim of this ex vivo study was to determine the minimum and maximum diameters and shape of the physiological apical foramen in the roots of maxillary and mandibular first molars. A descriptive study was conducted on 89 recently extracted first molars. Roots 3–5 mm from the apex were sectioned and prepared for analysis at 40× magnification. The minimum and maximum diameters of each physiological foramen were measured using the program Motic Images plus 2.0 ML. The shape of the foramina, classified as round, oval or irregular, was determined by the difference between the maximum and minimum diameters. A total of 174 physiological foramina were analyzed. The average of the minimum and maximum diameters was between 0.24–0.33 mm in maxillary first molars and between 0.25–0.33 mm in mandibular first molars. In maxillary molars, the most common shape of the foramen was oval (50%), then irregular (32%), then round (18%). In mandibular molars, the oval shape was also the most frequent (59%), followed by irregular (23%) and round (18%). The findings of this study regarding the morphology of physiological apical foramina in first molars make it easier for the operator to choose the appropriately-sized instruments to perform endodontic therapy successfully. PMID:25937698

Morphology of the Physiological Apical Foramen in Maxillary and Mandibular First Molars.

PubMed

Abarca, J; Zaror, C; Monardes, H; Hermosilla, V; Muñoz, C; Cantin, M

2014-06-01

Information regarding the anatomy of the physiological apical foramen is limited. Knowing its diameter and shapes contributes to clinical work, specifically to the cleaning and shaping of the apical third. The aim of this ex vivo study was to determine the minimum and maximum diameters and shape of the physiological apical foramen in the roots of maxillary and mandibular first molars. A descriptive study was conducted on 89 recently extracted first molars. Roots 3-5 mm from the apex were sectioned and prepared for analysis at 40× magnification. The minimum and maximum diameters of each physiological foramen were measured using the program Motic Images plus 2.0 ML. The shape of the foramina, classified as round, oval or irregular, was determined by the difference between the maximum and minimum diameters. A total of 174 physiological foramina were analyzed. The average of the minimum and maximum diameters was between 0.24-0.33 mm in maxillary first molars and between 0.25-0.33 mm in mandibular first molars. In maxillary molars, the most common shape of the foramen was oval (50%), then irregular (32%), then round (18%). In mandibular molars, the oval shape was also the most frequent (59%), followed by irregular (23%) and round (18%). The findings of this study regarding the morphology of physiological apical foramina in first molars make it easier for the operator to choose the appropriately-sized instruments to perform endodontic therapy successfully.

SU-F-18C-01: Minimum Detectability Analysis for Comprehensive Sized Based Optimization of Image Quality and Radiation Dose Across CT Protocols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smitherman, C; Chen, B; Samei, E

2014-06-15

Purpose: This work involved a comprehensive modeling of task-based performance of CT across a wide range of protocols. The approach was used for optimization and consistency of dose and image quality within a large multi-vendor clinical facility. Methods: 150 adult protocols from the Duke University Medical Center were grouped into sub-protocols with similar acquisition characteristics. A size based image quality phantom (Duke Mercury Phantom) was imaged using these sub-protocols for a range of clinically relevant doses on two CT manufacturer platforms (Siemens, GE). The images were analyzed to extract task-based image quality metrics such as the Task Transfer Function (TTF),more » Noise Power Spectrum, and Az based on designer nodule task functions. The data were analyzed in terms of the detectability of a lesion size/contrast as a function of dose, patient size, and protocol. A graphical user interface (GUI) was developed to predict image quality and dose to achieve a minimum level of detectability. Results: Image quality trends with variations in dose, patient size, and lesion contrast/size were evaluated and calculated data behaved as predicted. The GUI proved effective to predict the Az values representing radiologist confidence for a targeted lesion, patient size, and dose. As an example, an abdomen pelvis exam for the GE scanner, with a task size/contrast of 5-mm/50-HU, and an Az of 0.9 requires a dose of 4.0, 8.9, and 16.9 mGy for patient diameters of 25, 30, and 35 cm, respectively. For a constant patient diameter of 30 cm, the minimum detected lesion size at those dose levels would be 8.4, 5, and 3.9 mm, respectively. Conclusion: The designed CT protocol optimization platform can be used to evaluate minimum detectability across dose levels and patient diameters. The method can be used to improve individual protocols as well as to improve protocol consistency across CT scanners.« less

Dual Energy Method for Breast Imaging: A Simulation Study.

PubMed

Koukou, V; Martini, N; Michail, C; Sotiropoulou, P; Fountzoula, C; Kalyvas, N; Kandarakis, I; Nikiforidis, G; Fountos, G

2015-01-01

Dual energy methods can suppress the contrast between adipose and glandular tissues in the breast and therefore enhance the visibility of calcifications. In this study, a dual energy method based on analytical modeling was developed for the detection of minimum microcalcification thickness. To this aim, a modified radiographic X-ray unit was considered, in order to overcome the limited kVp range of mammographic units used in previous DE studies, combined with a high resolution CMOS sensor (pixel size of 22.5 μm) for improved resolution. Various filter materials were examined based on their K-absorption edge. Hydroxyapatite (HAp) was used to simulate microcalcifications. The contrast to noise ratio (CNR tc ) of the subtracted images was calculated for both monoenergetic and polyenergetic X-ray beams. The optimum monoenergetic pair was 23/58 keV for the low and high energy, respectively, resulting in a minimum detectable microcalcification thickness of 100 μm. In the polyenergetic X-ray study, the optimal spectral combination was 40/70 kVp filtered with 100 μm cadmium and 1000 μm copper, respectively. In this case, the minimum detectable microcalcification thickness was 150 μm. The proposed dual energy method provides improved microcalcification detectability in breast imaging with mean glandular dose values within acceptable levels.

Dual Energy Method for Breast Imaging: A Simulation Study

PubMed Central

2015-01-01

Dual energy methods can suppress the contrast between adipose and glandular tissues in the breast and therefore enhance the visibility of calcifications. In this study, a dual energy method based on analytical modeling was developed for the detection of minimum microcalcification thickness. To this aim, a modified radiographic X-ray unit was considered, in order to overcome the limited kVp range of mammographic units used in previous DE studies, combined with a high resolution CMOS sensor (pixel size of 22.5 μm) for improved resolution. Various filter materials were examined based on their K-absorption edge. Hydroxyapatite (HAp) was used to simulate microcalcifications. The contrast to noise ratio (CNRtc) of the subtracted images was calculated for both monoenergetic and polyenergetic X-ray beams. The optimum monoenergetic pair was 23/58 keV for the low and high energy, respectively, resulting in a minimum detectable microcalcification thickness of 100 μm. In the polyenergetic X-ray study, the optimal spectral combination was 40/70 kVp filtered with 100 μm cadmium and 1000 μm copper, respectively. In this case, the minimum detectable microcalcification thickness was 150 μm. The proposed dual energy method provides improved microcalcification detectability in breast imaging with mean glandular dose values within acceptable levels. PMID:26246848

7 CFR 51.1859 - Size.

Code of Federal Regulations, 2011 CFR

2011-01-01

... cherry tomatoes and Pyriforme type tomatoes commonly referred to as pear shaped tomatoes, and other... Standards for Fresh Tomatoes 1 Size § 51.1859 Size. (a) The size of tomatoes packed in any standard type... measurement for minimum diameter shall be the largest diameter of the tomato measured at right angles to a...

7 CFR 51.1859 - Size.

Code of Federal Regulations, 2010 CFR

2010-01-01

... cherry tomatoes and Pyriforme type tomatoes commonly referred to as pear shaped tomatoes, and other... Standards for Fresh Tomatoes 1 Size § 51.1859 Size. (a) The size of tomatoes packed in any standard type... measurement for minimum diameter shall be the largest diameter of the tomato measured at right angles to a...

Phylogenetic analyses suggest that diversification and body size evolution are independent in insects.

PubMed

Rainford, James L; Hofreiter, Michael; Mayhew, Peter J

2016-01-08

Skewed body size distributions and the high relative richness of small-bodied taxa are a fundamental property of a wide range of animal clades. The evolutionary processes responsible for generating these distributions are well described in vertebrate model systems but have yet to be explored in detail for other major terrestrial clades. In this study, we explore the macro-evolutionary patterns of body size variation across families of Hexapoda (insects and their close relatives), using recent advances in phylogenetic understanding, with an aim to investigate the link between size and diversity within this ancient and highly diverse lineage. The maximum, minimum and mean-log body lengths of hexapod families are all approximately log-normally distributed, consistent with previous studies at lower taxonomic levels, and contrasting with skewed distributions typical of vertebrate groups. After taking phylogeny and within-tip variation into account, we find no evidence for a negative relationship between diversification rate and body size, suggesting decoupling of the forces controlling these two traits. Likelihood-based modeling of the log-mean body size identifies distinct processes operating within Holometabola and Diptera compared with other hexapod groups, consistent with accelerating rates of size evolution within these clades, while as a whole, hexapod body size evolution is found to be dominated by neutral processes including significant phylogenetic conservatism. Based on our findings we suggest that the use of models derived from well-studied but atypical clades, such as vertebrates may lead to misleading conclusions when applied to other major terrestrial lineages. Our results indicate that within hexapods, and within the limits of current systematic and phylogenetic knowledge, insect diversification is generally unfettered by size-biased macro-evolutionary processes, and that these processes over large timescales tend to converge on apparently neutral evolutionary processes. We also identify limitations on available data within the clade and modeling approaches for the resolution of trees of higher taxa, the resolution of which may collectively enhance our understanding of this key component of terrestrial ecosystems.

Three-dimensional laser cooling at the Doppler limit

NASA Astrophysics Data System (ADS)

Chang, R.; Hoendervanger, A. L.; Bouton, Q.; Fang, Y.; Klafka, T.; Audo, K.; Aspect, A.; Westbrook, C. I.; Clément, D.

2014-12-01

Many predictions of Doppler-cooling theory of two-level atoms have never been verified in a three-dimensional geometry, including the celebrated minimum achievable temperature ℏ Γ /2 kB , where Γ is the transition linewidth. Here we show that, despite their degenerate level structure, we can use helium-4 atoms to achieve a situation in which these predictions can be verified. We make measurements of atomic temperatures, magneto-optical trap sizes, and the sensitivity of optical molasses to a power imbalance in the laser beams, finding excellent agreement with Doppler theory. We show that the special properties of helium, particularly its small mass and narrow transition linewidth, prevent effective sub-Doppler cooling with red-detuned optical molasses. This discussion can be generalized to identify when a given species is likely to be subject to the same limitation.

Calculation of Appropriate Minimum Size of Isolation Rooms based on Questionnaire Survey of Experts and Analysis on Conditions of Isolation Room Use

NASA Astrophysics Data System (ADS)

Won, An-Na; Song, Hae-Eun; Yang, Young-Kwon; Park, Jin-Chul; Hwang, Jung-Ha

2017-07-01

After the outbreak of the MERS (Middle East Respiratory Syndrome) epidemic, issues were raised regarding response capabilities of medical institutions, including the lack of isolation rooms at hospitals. Since then, the government of Korea has been revising regulations to enforce medical laws in order to expand the operation of isolation rooms and to strengthen standards regarding their mandatory installation at hospitals. Among general and tertiary hospitals in Korea, a total of 159 are estimated to be required to install isolation rooms to meet minimum standards. For the purpose of contributing to hospital construction plans in the future, this study conducted a questionnaire survey of experts and analysed the environment and devices necessary in isolation rooms, to determine their appropriate minimum size to treat patients. The result of the analysis is as follows: First, isolation rooms at hospitals are required to have a minimum 3,300mm minor axis and a minimum 5,000mm major axis for the isolation room itself, and a minimum 1,800mm minor axis for the antechamber where personal protective equipment is donned and removed. Second, the 15 ㎡-or-larger standard for the floor area of isolation rooms will have to be reviewed and standards for the minimum width of isolation rooms will have to be established.

Binomial Test Method for Determining Probability of Detection Capability for Fracture Critical Applications

NASA Technical Reports Server (NTRS)

Generazio, Edward R.

2011-01-01

The capability of an inspection system is established by applications of various methodologies to determine the probability of detection (POD). One accepted metric of an adequate inspection system is that for a minimum flaw size and all greater flaw sizes, there is 0.90 probability of detection with 95% confidence (90/95 POD). Directed design of experiments for probability of detection (DOEPOD) has been developed to provide an efficient and accurate methodology that yields estimates of POD and confidence bounds for both Hit-Miss or signal amplitude testing, where signal amplitudes are reduced to Hit-Miss by using a signal threshold Directed DOEPOD uses a nonparametric approach for the analysis or inspection data that does require any assumptions about the particular functional form of a POD function. The DOEPOD procedure identifies, for a given sample set whether or not the minimum requirement of 0.90 probability of detection with 95% confidence is demonstrated for a minimum flaw size and for all greater flaw sizes (90/95 POD). The DOEPOD procedures are sequentially executed in order to minimize the number of samples needed to demonstrate that there is a 90/95 POD lower confidence bound at a given flaw size and that the POD is monotonic for flaw sizes exceeding that 90/95 POD flaw size. The conservativeness of the DOEPOD methodology results is discussed. Validated guidelines for binomial estimation of POD for fracture critical inspection are established.

Feasibility of rotating fluidized bed reactor for rocket propulsion

NASA Technical Reports Server (NTRS)

Ludewig, H.; Manning, A. J.; Raseman, C. J.

1974-01-01

The rotating fluidized bed reactor concept is outlined, and its application to rocket propulsion is discussed. Experimental results obtained indicate that minimum fluidization correlations commonly in use for 1-g beds can also be applied to multiple-g beds. It was found that for a low thrust system (20,000 lbf) the fuel particle size and/or particle stress play a limiting role on performance. The superiority of U-233 as a fuel for this type of rocket engine is clearly demonstrated in the analysis. The maximum thrust/weight ratio for a 90,000N thrust engine was found to be approximately 65N/kg.

A novel fast optical switch based on two cascaded Terahertz Optical Asymmetric Demultiplexers (TOAD).

PubMed

Wang, Bing; Baby, Varghese; Tong, Wilson; Xu, Lei; Friedman, Michelle; Runser, Robert; Glesk, Ivan; Prucnal, Paul

2002-01-14

A novel optical switch based on cascading two terahertz optical asymmetric demultiplexers (TOAD) is presented. By utilizing the sharp edge of the asymmetric TOAD switching window profile, two TOAD switching windows are overlapped to produce a narrower aggregate switching window, not limited by the pulse propagation time in the SOA of the TOAD. Simulations of the cascaded TOAD switching window show relatively constant window amplitude for different window sizes. Experimental results on cascading two TOADs, each with a switching window of 8ps, but with the SOA on opposite sides of the fiber loop, show a minimum switching window of 2.7ps.

AEROSOL PARTICLE COLLECTOR DESIGN STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S; Richard Dimenna, R

2007-09-27

A computational evaluation of a particle collector design was performed to evaluate the behavior of aerosol particles in a fast flowing gas stream. The objective of the work was to improve the collection efficiency of the device while maintaining a minimum specified air throughput, nominal collector size, and minimal power requirements. The impact of a range of parameters was considered subject to constraints on gas flow rate, overall collector dimensions, and power limitations. Potential improvements were identified, some of which have already been implemented. Other more complex changes were identified and are described here for further consideration. In addition, fruitfulmore » areas for further study are proposed.« less

Excitations in the Yang–Gaudin Bose gas

DOE PAGES

Robinson, Neil J.; Konik, Robert M.

2017-06-01

Here, we study the excitation spectrum of two-component delta-function interacting bosons confined to a single spatial dimension, the Yang–Gaudin Bose gas. We show that there are pronounced finite-size effects in the dispersion relations of excitations, perhaps best illustrated by the spinon single particle dispersion which exhibits a gap at 2k F and a finite-momentum roton-like minimum. Such features occur at energies far above the finite volume excitation gap, vanish slowly as 1/L for fixed spinon number, and can persist to the thermodynamic limit at fixed spinon density. Features such as the 2k F gap also persist to multi-particle excitation continua. Our results show that excitations in the finite system can behave in a qualitatively different manner to analogous excitations in the thermodynamic limit. The Yang–Gaudin Bose gas is also host to multi-spinon bound states, known asmore » $$\\Lambda$$ -strings. We study these excitations both in the thermodynamic limit under the string hypothesis and in finite size systems where string deviations are taken into account. In the zero-temperature limit we present a simple relation between the length n $$\\Lambda$$-string dressed energies $$\\epsilon_n(\\lambda)$$ and the dressed energy $$\\epsilon(k)$$. We solve the Yang–Yang–Takahashi equations numerically and compare to the analytical solution obtained under the strong couple expansion, revealing that the length n $$\\Lambda$$ -string dressed energy is Lorentzian over a wide range of real string centers λ in the vicinity of $$\\lambda = 0$$ . We then examine the finite size effects present in the dispersion of the two-spinon bound states by numerically solving the Bethe ansatz equations with string deviations.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, Neil J.; Konik, Robert M.

Here, we study the excitation spectrum of two-component delta-function interacting bosons confined to a single spatial dimension, the Yang–Gaudin Bose gas. We show that there are pronounced finite-size effects in the dispersion relations of excitations, perhaps best illustrated by the spinon single particle dispersion which exhibits a gap at 2k F and a finite-momentum roton-like minimum. Such features occur at energies far above the finite volume excitation gap, vanish slowly as 1/L for fixed spinon number, and can persist to the thermodynamic limit at fixed spinon density. Features such as the 2k F gap also persist to multi-particle excitation continua. Our results show that excitations in the finite system can behave in a qualitatively different manner to analogous excitations in the thermodynamic limit. The Yang–Gaudin Bose gas is also host to multi-spinon bound states, known asmore » $$\\Lambda$$ -strings. We study these excitations both in the thermodynamic limit under the string hypothesis and in finite size systems where string deviations are taken into account. In the zero-temperature limit we present a simple relation between the length n $$\\Lambda$$-string dressed energies $$\\epsilon_n(\\lambda)$$ and the dressed energy $$\\epsilon(k)$$. We solve the Yang–Yang–Takahashi equations numerically and compare to the analytical solution obtained under the strong couple expansion, revealing that the length n $$\\Lambda$$ -string dressed energy is Lorentzian over a wide range of real string centers λ in the vicinity of $$\\lambda = 0$$ . We then examine the finite size effects present in the dispersion of the two-spinon bound states by numerically solving the Bethe ansatz equations with string deviations.« less

E-Area Low-Level Waste Facility Cover Overhang Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hang, T.; Flach, G. P.

2016-05-18

PORFLOW related analyses were performed with a focus on Slit and Engineered Trenches to evaluate the minimum required cover overhang size that would prevent any adverse impact on the ELLWF overall performance. Cover overhang is defined as the lateral distance that a low-infiltration cover extends beyond the edge of the trench unit in any direction. Analyses were carried out for H-3 (short half-life), I-129 (very long half-life), and Sr-90 (moderate half-life with intermediate K d) at different overhang sizes (5ft, 10ft, 20ft, 50ft, and infinite), cover timing (0yr, 10yr, 20yr, and 30yr), and scenarios (Intact and a limited Dynamic Compactionmore » Case). H-3, I-129 and Sr-90 are representative of nuclides that typically drive the sum-of-fractions for a trench disposal unit.« less

Monte Carlo analysis of tagged neutron beams for cargo container inspection.

PubMed

Pesente, S; Lunardon, M; Nebbia, G; Viesti, G; Sudac, D; Valkovic, V

2007-12-01

Fast neutrons produced via D+T reactions and tagged by the associated particle technique have been recently proposed to inspect cargo containers. The general characteristics of this technique are studied with Monte Carlo simulations by determining the properties of the tagged neutron beams as a function of the relevant design parameters (energy and size of the deuteron beam, geometry of the charged particle detector). Results from simulations, validated by experiments, show that the broadening of the correlation between the alpha-particle and the neutron, induced by kinematical as well as geometrical (beam and detector size) effects, is important and limits the dimension of the minimum voxel to be inspected. Moreover, the effect of the container filling is explored. The material filling produces a sizeable loss of correlation between alpha-particles and neutrons due to scattering and absorption. Conditions in inspecting cargo containers are discussed.

Complexity of Fit, with Application to Space Suits

NASA Technical Reports Server (NTRS)

Rajulu, Sudhakar; Benson, Elizabeth

2009-01-01

Although fitting a garment is often considered more of an art than a science, experts suggest that a subjectively poor fit is a symptom of inappropriate ease, the space between the wearer and the garment. The condition of poor suit fit is a unique problem for the space program and it can be attributed primarily to: a) NASA s policy to accommodate a wide variety of people (males and females from 1st to 99th percentile range and with various shapes and sizes) and b) its requirement to deploy a minimum number of suit sizes for logistical reasons. These factors make the space suit fit difficult to assess, where a wide range of people must be fit by the minimum possible number of suits, and yet, fit is crucial for operability and safety. Existing simplistic sizing scheme do not account for wide variations in shape within a diverse population with very limited sizing options. The complex issue of fit has been addressed by a variety of methods, many of which have been developed by the military, which has always had a keen interest in fitting its diverse population but with a multitude of sizing options. The space program has significantly less sizing options, so a combination of these advanced methods should be used to optimize space suit size and assess space suit fit. Multivariate methods can be used to develop sizing schemes that better reflect the wearer population, and integrated sizing systems can form a compromise between fitting men and women. Range of motion and operability testing can be combined with subjective feedback to provide a comprehensive evaluation of fit. The amount of ease can be tailored using these methods, to provide enough extra room where it is needed, without compromising mobility and comfort. This paper discusses the problem of fit in one of its most challenging applications: providing a safe and comfortable spacesuit that will protect its wearer from the extreme environment of space. It will discuss the challenges and necessity of closely fitting its potential wearers, a group of people from a broad spectrum of the population, and will detail some of the methods that can be employed to ensure and validate a good fit.

49 CFR Appendix A to Part 172 - Office of Hazardous Materials Transportation Color Tolerance Charts and Tables

Code of Federal Regulations, 2010 CFR

2010-10-01

... .3308 .2328 Dark 10.0P 4.0/10 12.00 .3306 .2162 1 Maximum chroma is not limited. 2 For the colors green and purple, the minimum saturation (chroma) limits for porcelain enamel on metal are lower than for most other surface coatings. Therefore, the minimum chroma limits of these two colors as displayed on...

40 CFR Table 11 to Subpart Xxxx of... - Minimum Data for Continuous Compliance With the Emission Limits for Tire Cord Production Affected...

Code of Federal Regulations, 2010 CFR

2010-07-01

... With the Emission Limits for Tire Cord Production Affected Sources 11 Table 11 to Subpart XXXX of Part... for Hazardous Air Pollutants: Rubber Tire Manufacturing Pt. 63, Subpt. XXXX, Table 11 Table 11 to Subpart XXXX of Part 63—Minimum Data for Continuous Compliance With the Emission Limits for Tire Cord...

Determination of the Minimum Use Level of Fuel System Icing Inhibitor (FSII) in JP-8 That Will Provide Adquate Icing Inhibition and Biostatic Protection for Air Force Aircraft

DTIC Science & Technology

2013-12-01

experimental studies and analyses performed and the resulting recommendations. Results from the present effort indicated that a minimum use limit of... experimental studies performed and the resulting recommendations regarding the minimum on-board use limit of FSII while maintaining safe operability...sumping. A detailed summary of the experimental efforts and results are provided in a separate report (Balster et al., 2010). For the ATCC

Application of indigenous sulfur-oxidizing bacteria from municipal wastewater to selectively bioleach phosphorus from high-phosphorus iron ore: effect of particle size.

PubMed

Shen, Shaobo; Rao, Ruirui; Wang, Jincao

2013-01-01

The effects of ore particle size on selectively bioleaching phosphorus (P) from high-phosphorus iron ore were studied. The average contents of P and Fe in the iron ore were 1.06 and 47.90% (w/w), respectively. The particle sizes of the ores used ranged from 58 to 3350 microm. It was found that the indigenous sulfur-oxidizing bacteria from municipal wastewater could grow well in the slurries of solid high-phosphorus iron ore and municipal wastewater. The minimum bioleaching pH reached for the current work was 0.33. The P content in bioleached iron ore reduced slightly with decreasing particle size, while the removal percentage of Fe decreased appreciably with decreasing particle size. The optimal particle size fraction was 58-75 microm, because the P content in bioleached iron ore reached a minimum of 0.16% (w/w), the removal percentage of P attained a maximum of 86.7%, while the removal percentage of Fe dropped to a minimum of 1.3% and the Fe content in bioleached iron ore was a maximum of 56.4% (w/w) in this case. The iron ores thus obtained were suitable to be used in the iron-making process. The removal percentage of ore solid decreased with decreasing particle size at particle size range of 106-3350 microm. The possible reasons resulting in above phenomena were explored in the current work. It was inferred that the particle sizes of the iron ore used in this work have no significant effect on the viability of the sulfur-oxidizing bacteria.

20 CFR 229.48 - Family maximum.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Family maximum. 229.48 Section 229.48... OVERALL MINIMUM GUARANTEE Computation of the Overall Minimum Rate § 229.48 Family maximum. (a) Family... month on one person's earnings record is limited. This limited amount is called the family maximum. The...

Sample size of the reference sample in a case-augmented study.

PubMed

Ghosh, Palash; Dewanji, Anup

2017-05-01

The case-augmented study, in which a case sample is augmented with a reference (random) sample from the source population with only covariates information known, is becoming popular in different areas of applied science such as pharmacovigilance, ecology, and econometrics. In general, the case sample is available from some source (for example, hospital database, case registry, etc.); however, the reference sample is required to be drawn from the corresponding source population. The required minimum size of the reference sample is an important issue in this regard. In this work, we address the minimum sample size calculation and discuss related issues. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

50 CFR 622.48 - Adjustment of management measures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... biomass achieved by fishing at MSY (BMSY) (or proxy), maximum fishing mortality threshold (MFMT), minimum... biomass achieved by fishing at MSY (BMSY), minimum stock size threshold (MSST), and maximum fishing.... MSY, OY, and TAC. (f) South Atlantic snapper-grouper and wreckfish. Biomass levels, age-structured...

78 FR 3923 - Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-17

... impact of tick sizes on small and middle capitalization companies, the economic consequences (including the costs and benefits) of increasing or decreasing minimum tick sizes, and whether other policy... the second panel will address the impact of tick sizes on the securities market in general, including...

Rate-Compatible LDPC Codes with Linear Minimum Distance

NASA Technical Reports Server (NTRS)

Divsalar, Dariush; Jones, Christopher; Dolinar, Samuel

2009-01-01

A recently developed method of constructing protograph-based low-density parity-check (LDPC) codes provides for low iterative decoding thresholds and minimum distances proportional to block sizes, and can be used for various code rates. A code constructed by this method can have either fixed input block size or fixed output block size and, in either case, provides rate compatibility. The method comprises two submethods: one for fixed input block size and one for fixed output block size. The first mentioned submethod is useful for applications in which there are requirements for rate-compatible codes that have fixed input block sizes. These are codes in which only the numbers of parity bits are allowed to vary. The fixed-output-blocksize submethod is useful for applications in which framing constraints are imposed on the physical layers of affected communication systems. An example of such a system is one that conforms to one of many new wireless-communication standards that involve the use of orthogonal frequency-division modulation

Best Merge Region Growing Segmentation with Integrated Non-Adjacent Region Object Aggregation

NASA Technical Reports Server (NTRS)

Tilton, James C.; Tarabalka, Yuliya; Montesano, Paul M.; Gofman, Emanuel

2012-01-01

Best merge region growing normally produces segmentations with closed connected region objects. Recognizing that spectrally similar objects often appear in spatially separate locations, we present an approach for tightly integrating best merge region growing with non-adjacent region object aggregation, which we call Hierarchical Segmentation or HSeg. However, the original implementation of non-adjacent region object aggregation in HSeg required excessive computing time even for moderately sized images because of the required intercomparison of each region with all other regions. This problem was previously addressed by a recursive approximation of HSeg, called RHSeg. In this paper we introduce a refined implementation of non-adjacent region object aggregation in HSeg that reduces the computational requirements of HSeg without resorting to the recursive approximation. In this refinement, HSeg s region inter-comparisons among non-adjacent regions are limited to regions of a dynamically determined minimum size. We show that this refined version of HSeg can process moderately sized images in about the same amount of time as RHSeg incorporating the original HSeg. Nonetheless, RHSeg is still required for processing very large images due to its lower computer memory requirements and amenability to parallel processing. We then note a limitation of RHSeg with the original HSeg for high spatial resolution images, and show how incorporating the refined HSeg into RHSeg overcomes this limitation. The quality of the image segmentations produced by the refined HSeg is then compared with other available best merge segmentation approaches. Finally, we comment on the unique nature of the hierarchical segmentations produced by HSeg.

Set size manipulations reveal the boundary conditions of perceptual ensemble learning.

PubMed

Chetverikov, Andrey; Campana, Gianluca; Kristjánsson, Árni

2017-11-01

Recent evidence suggests that observers can grasp patterns of feature variations in the environment with surprising efficiency. During visual search tasks where all distractors are randomly drawn from a certain distribution rather than all being homogeneous, observers are capable of learning highly complex statistical properties of distractor sets. After only a few trials (learning phase), the statistical properties of distributions - mean, variance and crucially, shape - can be learned, and these representations affect search during a subsequent test phase (Chetverikov, Campana, & Kristjánsson, 2016). To assess the limits of such distribution learning, we varied the information available to observers about the underlying distractor distributions by manipulating set size during the learning phase in two experiments. We found that robust distribution learning only occurred for large set sizes. We also used set size to assess whether the learning of distribution properties makes search more efficient. The results reveal how a certain minimum of information is required for learning to occur, thereby delineating the boundary conditions of learning of statistical variation in the environment. However, the benefits of distribution learning for search efficiency remain unclear. Copyright © 2017 Elsevier Ltd. All rights reserved.

Unleashing the Power of Distributed CPU/GPU Architectures: Massive Astronomical Data Analysis and Visualization Case Study

NASA Astrophysics Data System (ADS)

Hassan, A. H.; Fluke, C. J.; Barnes, D. G.

2012-09-01

Upcoming and future astronomy research facilities will systematically generate terabyte-sized data sets moving astronomy into the Petascale data era. While such facilities will provide astronomers with unprecedented levels of accuracy and coverage, the increases in dataset size and dimensionality will pose serious computational challenges for many current astronomy data analysis and visualization tools. With such data sizes, even simple data analysis tasks (e.g. calculating a histogram or computing data minimum/maximum) may not be achievable without access to a supercomputing facility. To effectively handle such dataset sizes, which exceed today's single machine memory and processing limits, we present a framework that exploits the distributed power of GPUs and many-core CPUs, with a goal of providing data analysis and visualizing tasks as a service for astronomers. By mixing shared and distributed memory architectures, our framework effectively utilizes the underlying hardware infrastructure handling both batched and real-time data analysis and visualization tasks. Offering such functionality as a service in a “software as a service” manner will reduce the total cost of ownership, provide an easy to use tool to the wider astronomical community, and enable a more optimized utilization of the underlying hardware infrastructure.

Giant boid snake from the Palaeocene neotropics reveals hotter past equatorial temperatures.

PubMed

Head, Jason J; Bloch, Jonathan I; Hastings, Alexander K; Bourque, Jason R; Cadena, Edwin A; Herrera, Fabiany A; Polly, P David; Jaramillo, Carlos A

2009-02-05

The largest extant snakes live in the tropics of South America and southeast Asia where high temperatures facilitate the evolution of large body sizes among air-breathing animals whose body temperatures are dependant on ambient environmental temperatures (poikilothermy). Very little is known about ancient tropical terrestrial ecosystems, limiting our understanding of the evolution of giant snakes and their relationship to climate in the past. Here we describe a boid snake from the oldest known neotropical rainforest fauna from the Cerrejón Formation (58-60 Myr ago) in northeastern Colombia. We estimate a body length of 13 m and a mass of 1,135 kg, making it the largest known snake. The maximum size of poikilothermic animals at a given temperature is limited by metabolic rate, and a snake of this size would require a minimum mean annual temperature of 30-34 degrees C to survive. This estimate is consistent with hypotheses of hot Palaeocene neotropics with high concentrations of atmospheric CO(2) based on climate models. Comparison of palaeotemperature estimates from the equator to those from South American mid-latitudes indicates a relatively steep temperature gradient during the early Palaeogene greenhouse, similar to that of today. Depositional environments and faunal composition of the Cerrejón Formation indicate an anaconda-like ecology for the giant snake, and an earliest Cenozoic origin of neotropical vertebrate faunas.

Soil carbon inventories under a bioenergy crop (switchgrass): Measurement limitations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garten, C.T. Jr.; Wullschleger, S.D.

Approximately 5 yr after planting, coarse root carbon (C) and soil organic C (SOC) inventories were compared under different types of plant cover at four switchgrass (Panicum virgatum L.) production field trials in the southeastern USA. There was significantly more coarse root C under switchgrass (Alamo variety) and forest cover than tall fescue (Festuca arundinacea Schreb.), corn (Zea mays L.), or native pastures of mixed grasses. Inventories of SOC under switchgrass were not significantly greater than SOC inventories under other plant covers. At some locations the statistical power associated with ANOVA of SOC inventories was low, which raised questions aboutmore » whether differences in SOC could be detected statistically. A minimum detectable difference (MDD) for SOC inventories was calculated. The MDD is the smallest detectable difference between treatment means once the variation, significance level, statistical power, and sample size are specified. The analysis indicated that a difference of {approx}50 mg SOC/cm{sup 2} or 5 Mg SOC/ha, which is {approx}10 to 15% of existing SOC, could be detected with reasonable sample sizes and good statistical power. The smallest difference in SOC inventories that can be detected, and only with exceedingly large sample sizes, is {approx}2 to 3%. These measurement limitations have implications for monitoring and verification of proposals to ameliorate increasing global atmospheric CO{sub 2} concentrations by sequestering C in soils.« less

Menu Plans: Maximum Nutrition for Minimum Cost.

ERIC Educational Resources Information Center

Texas Child Care, 1995

1995-01-01

Suggests that menu planning is the key to getting maximum nutrition in day care meals and snacks for minimum cost. Explores United States Department of Agriculture food pyramid guidelines for children and tips for planning menus and grocery shopping. Includes suggested meal patterns and portion sizes. (HTH)

MINIMUM AREAS FOR ELEMENTARY SCHOOL BUILDING FACILITIES.

ERIC Educational Resources Information Center

Pennsylvania State Dept. of Public Instruction, Harrisburg.

MINIMUM AREA SPACE REQUIREMENTS IN SQUARE FOOTAGE FOR ELEMENTARY SCHOOL BUILDING FACILITIES ARE PRESENTED, INCLUDING FACILITIES FOR INSTRUCTIONAL USE, GENERAL USE, AND SERVICE USE. LIBRARY, CAFETERIA, KITCHEN, STORAGE, AND MULTIPURPOSE ROOMS SHOULD BE SIZED FOR THE PROJECTED ENROLLMENT OF THE BUILDING IN ACCORDANCE WITH THE PROJECTION UNDER THE…

Nanoparticle size detection limits by single particle ICP-MS for 40 elements.

PubMed

Lee, Sungyun; Bi, Xiangyu; Reed, Robert B; Ranville, James F; Herckes, Pierre; Westerhoff, Paul

2014-09-02

The quantification and characterization of natural, engineered, and incidental nano- to micro-size particles are beneficial to assessing a nanomaterial's performance in manufacturing, their fate and transport in the environment, and their potential risk to human health. Single particle inductively coupled plasma mass spectrometry (spICP-MS) can sensitively quantify the amount and size distribution of metallic nanoparticles suspended in aqueous matrices. To accurately obtain the nanoparticle size distribution, it is critical to have knowledge of the size detection limit (denoted as Dmin) using spICP-MS for a wide range of elements (other than a few available assessed ones) that have been or will be synthesized into engineered nanoparticles. Herein is described a method to estimate the size detection limit using spICP-MS and then apply it to nanoparticles composed of 40 different elements. The calculated Dmin values correspond well for a few of the elements with their detectable sizes that are available in the literature. Assuming each nanoparticle sample is composed of one element, Dmin values vary substantially among the 40 elements: Ta, U, Ir, Rh, Th, Ce, and Hf showed the lowest Dmin values, ≤10 nm; Bi, W, In, Pb, Pt, Ag, Au, Tl, Pd, Y, Ru, Cd, and Sb had Dmin in the range of 11-20 nm; Dmin values of Co, Sr, Sn, Zr, Ba, Te, Mo, Ni, V, Cu, Cr, Mg, Zn, Fe, Al, Li, and Ti were located at 21-80 nm; and Se, Ca, and Si showed high Dmin values, greater than 200 nm. A range of parameters that influence the Dmin, such as instrument sensitivity, nanoparticle density, and background noise, is demonstrated. It is observed that, when the background noise is low, the instrument sensitivity and nanoparticle density dominate the Dmin significantly. Approaches for reducing the Dmin, e.g., collision cell technology (CCT) and analyte isotope selection, are also discussed. To validate the Dmin estimation approach, size distributions for three engineered nanoparticle samples were obtained using spICP-MS. The use of this methodology confirms that the observed minimum detectable sizes are consistent with the calculated Dmin values. Overall, this work identifies the elements and nanoparticles to which current spICP-MS approaches can be applied, in order to enable quantification of very small nanoparticles at low concentrations in aqueous media.

48 CFR 8.1102 - Presolicitation requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... that— (1) The vehicles requested are of maximum fuel efficiency and minimum body size, engine size, and... automobiles (sedans and station wagons) larger than Type IA, IB, or II (small, subcompact, or compact) are...

48 CFR 8.1102 - Presolicitation requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... that— (1) The vehicles requested are of maximum fuel efficiency and minimum body size, engine size, and... automobiles (sedans and station wagons) larger than Type IA, IB, or II (small, subcompact, or compact) are...

48 CFR 8.1102 - Presolicitation requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... that— (1) The vehicles requested are of maximum fuel efficiency and minimum body size, engine size, and... automobiles (sedans and station wagons) larger than Type IA, IB, or II (small, subcompact, or compact) are...

48 CFR 8.1102 - Presolicitation requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... that— (1) The vehicles requested are of maximum fuel efficiency and minimum body size, engine size, and... automobiles (sedans and station wagons) larger than Type IA, IB, or II (small, subcompact, or compact) are...

48 CFR 8.1102 - Presolicitation requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... that— (1) The vehicles requested are of maximum fuel efficiency and minimum body size, engine size, and... automobiles (sedans and station wagons) larger than Type IA, IB, or II (small, subcompact, or compact) are...

The trade-off characteristics of acoustic and pressure sensors for the NASP

NASA Technical Reports Server (NTRS)

Winkler, Martin; Bush, Chuck

1992-01-01

Results of a trade study for the development of pressure and acoustic sensors for use on the National Aerospace Plane (NASP) are summarized. Pressure sensors are needed to operate to 100 psia; acoustic sensors are needed that can give meaningful information about a 200 dB sound pressure level (SPL) environment. Both sensors will have to operate from a high temperature of 2000 F down to absolute zero. The main conclusions of the study are the following: (1) Diaphragm materials limit minimum size and maximum frequency response attainable. (2) No transduction is available to meet all the NASP requirements with existing technology. (3) Capacitive sensors are large relative to the requirement, have limited resolution and frequency response due to noise, and cable length is limited to approximately 20 feet. (4) Eddy current sensors are large relative to the requirement and have limited cable lengths. (5) Fiber optic sensors provide the possibility for a small sensor, even though present developments do not exhibit that characteristic. The need to use sapphire at high temperature complicates the design. Present high temperature research sensors suffer from poor resolution. A significant development effort will be required to realize the potential of fiber optics. (6) Short-term development seems to favor eddy current techniques with the penalty of larger size and reduced dynamic range for acoustic sensors. (7) Long-term development may favor fiber optics with the penalties of cost, schedule, and uncertainty.

Physiological minimum temperatures for root growth in seven common European broad-leaved tree species.

PubMed

Schenker, Gabriela; Lenz, Armando; Körner, Christian; Hoch, Günter

2014-03-01

Temperature is the most important factor driving the cold edge distribution limit of temperate trees. Here, we identified the minimum temperatures for root growth in seven broad-leaved tree species, compared them with the species' natural elevational limits and identified morphological changes in roots produced near their physiological cold limit. Seedlings were exposed to a vertical soil-temperature gradient from 20 to 2 °C along the rooting zone for 18 weeks. In all species, the bulk of roots was produced at temperatures above 5 °C. However, the absolute minimum temperatures for root growth differed among species between 2.3 and 4.2 °C, with those species that reach their natural distribution limits at higher elevations also tending to have lower thermal limits for root tissue formation. In all investigated species, the roots produced at temperatures close to the thermal limit were pale, thick, unbranched and of reduced mechanical strength. Across species, the specific root length (m g(-1) root) was reduced by, on average, 60% at temperatures below 7 °C. A significant correlation of minimum temperatures for root growth with the natural high elevation limits of the investigated species indicates species-specific thermal requirements for basic physiological processes. Although these limits are not necessarily directly causative for the upper distribution limit of a species, they seem to belong to a syndrome of adaptive processes for life at low temperatures. The anatomical changes at the cold limit likely hint at the mechanisms impeding meristematic activity at low temperatures.

Disk Density Tuning of a Maximal Random Packing

PubMed Central

Ebeida, Mohamed S.; Rushdi, Ahmad A.; Awad, Muhammad A.; Mahmoud, Ahmed H.; Yan, Dong-Ming; English, Shawn A.; Owens, John D.; Bajaj, Chandrajit L.; Mitchell, Scott A.

2016-01-01

We introduce an algorithmic framework for tuning the spatial density of disks in a maximal random packing, without changing the sizing function or radii of disks. Starting from any maximal random packing such as a Maximal Poisson-disk Sampling (MPS), we iteratively relocate, inject (add), or eject (remove) disks, using a set of three successively more-aggressive local operations. We may achieve a user-defined density, either more dense or more sparse, almost up to the theoretical structured limits. The tuned samples are conflict-free, retain coverage maximality, and, except in the extremes, retain the blue noise randomness properties of the input. We change the density of the packing one disk at a time, maintaining the minimum disk separation distance and the maximum domain coverage distance required of any maximal packing. These properties are local, and we can handle spatially-varying sizing functions. Using fewer points to satisfy a sizing function improves the efficiency of some applications. We apply the framework to improve the quality of meshes, removing non-obtuse angles; and to more accurately model fiber reinforced polymers for elastic and failure simulations. PMID:27563162

Disk Density Tuning of a Maximal Random Packing.

PubMed

Ebeida, Mohamed S; Rushdi, Ahmad A; Awad, Muhammad A; Mahmoud, Ahmed H; Yan, Dong-Ming; English, Shawn A; Owens, John D; Bajaj, Chandrajit L; Mitchell, Scott A

2016-08-01

We introduce an algorithmic framework for tuning the spatial density of disks in a maximal random packing, without changing the sizing function or radii of disks. Starting from any maximal random packing such as a Maximal Poisson-disk Sampling (MPS), we iteratively relocate, inject (add), or eject (remove) disks, using a set of three successively more-aggressive local operations. We may achieve a user-defined density, either more dense or more sparse, almost up to the theoretical structured limits. The tuned samples are conflict-free, retain coverage maximality, and, except in the extremes, retain the blue noise randomness properties of the input. We change the density of the packing one disk at a time, maintaining the minimum disk separation distance and the maximum domain coverage distance required of any maximal packing. These properties are local, and we can handle spatially-varying sizing functions. Using fewer points to satisfy a sizing function improves the efficiency of some applications. We apply the framework to improve the quality of meshes, removing non-obtuse angles; and to more accurately model fiber reinforced polymers for elastic and failure simulations.

Growing Larger Crystals for Neutron Diffraction

NASA Technical Reports Server (NTRS)

Pusey, Marc

2003-01-01

Obtaining crystals of suitable size and high quality has been a major bottleneck in macromolecular crystallography. With the advent of advanced X-ray sources and methods the question of size has rapidly dwindled, almost to the point where if one can see the crystal then it was big enough. Quality is another issue, and major national and commercial efforts were established to take advantage of the microgravity environment in an effort to obtain higher quality crystals. Studies of the macromolecule crystallization process were carried out in many labs in an effort to understand what affected the resultant crystal quality on Earth, and how microgravity improved the process. While technological improvements are resulting in a diminishing of the minimum crystal size required, neutron diffraction structural studies still require considerably larger crystals, by several orders of magnitude, than X-ray studies. From a crystal growth physics perspective there is no reason why these 'large' crystals cannot be obtained: the question is generally more one of supply than limitations mechanism. This talk will discuss our laboratory s current model for macromolecule crystal growth, with highlights pertaining to the growth of crystals suitable for neutron diffraction studies.

Turbulence and star formation in molecular clouds

NASA Astrophysics Data System (ADS)

Larson, R. B.

1981-03-01

Consideration is given to the turbulence properties of molecular clouds and their implications for star formation. Data for 54 molecular clouds and condensations is presented which reveals cloud velocity dispersion and region size to follow a power-law relation, similar to the Kolmogoroff law for subsonic turbulence. Examination of the dynamics of the molecular clouds for which mass determinations are available reveals essentially all of them to be gravitationally bound, and to approximately satisfy the virial theorem. The observation of moderate scatter in the dispersion-size relation is noted to imply that most regions have not collapsed much since formation, suggesting that processes of turbulent hydrodynamics have played an important role in producing the observed substructures. A lower limit to the size of subcondensations at which their internal motions are no longer supersonic is shown to predict a minimum protostellar mass on the order of a few tenths of a solar mass, while massive protostellar clumps are found to develop complex internal structures, probably leading to the formation of prestellar condensation nuclei. The observed turbulence of molecular clouds is noted to imply lifetimes of less than 10 million years.

14 CFR 135.203 - VFR: Minimum altitudes.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false VFR: Minimum altitudes. 135.203 Section 135.203 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.203 VFR: Minimum altitudes. Except when necessary for...

14 CFR 135.203 - VFR: Minimum altitudes.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false VFR: Minimum altitudes. 135.203 Section 135.203 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.203 VFR: Minimum altitudes. Except when necessary for...

14 CFR 135.203 - VFR: Minimum altitudes.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false VFR: Minimum altitudes. 135.203 Section 135.203 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.203 VFR: Minimum altitudes. Except when necessary for...

26 CFR 1.514(c)-2 - Permitted allocations under section 514(c)(9)(E).

Code of Federal Regulations, 2013 CFR

2013-04-01

.... (ii) Limitation on chargebacks of partial allocations. (3) Minimum gain chargebacks attributable to nonrecourse deductions. (4) Minimum gain chargebacks attributable to distribution of nonrecourse debt proceeds. (i) Chargebacks disregarded until allocations made. (ii) Certain minimum gain chargebacks related to...

26 CFR 1.514(c)-2 - Permitted allocations under section 514(c)(9)(E).

Code of Federal Regulations, 2011 CFR

2011-04-01

.... (ii) Limitation on chargebacks of partial allocations. (3) Minimum gain chargebacks attributable to nonrecourse deductions. (4) Minimum gain chargebacks attributable to distribution of nonrecourse debt proceeds. (i) Chargebacks disregarded until allocations made. (ii) Certain minimum gain chargebacks related to...

26 CFR 1.514(c)-2 - Permitted allocations under section 514(c)(9)(E).

Code of Federal Regulations, 2014 CFR

2014-04-01

.... (ii) Limitation on chargebacks of partial allocations. (3) Minimum gain chargebacks attributable to nonrecourse deductions. (4) Minimum gain chargebacks attributable to distribution of nonrecourse debt proceeds. (i) Chargebacks disregarded until allocations made. (ii) Certain minimum gain chargebacks related to...

26 CFR 1.514(c)-2 - Permitted allocations under section 514(c)(9)(E).

Code of Federal Regulations, 2012 CFR

2012-04-01

.... (ii) Limitation on chargebacks of partial allocations. (3) Minimum gain chargebacks attributable to nonrecourse deductions. (4) Minimum gain chargebacks attributable to distribution of nonrecourse debt proceeds. (i) Chargebacks disregarded until allocations made. (ii) Certain minimum gain chargebacks related to...

46 CFR 108.437 - Pipe sizes and discharge rates for enclosed ventilation systems for rotating electrical equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Pipe sizes and discharge rates for enclosed ventilation... Systems Fixed Carbon Dioxide Fire Extinguishing Systems § 108.437 Pipe sizes and discharge rates for enclosed ventilation systems for rotating electrical equipment. (a) The minimum pipe size for the initial...

A Modal Approach to Compact MIMO Antenna Design

NASA Astrophysics Data System (ADS)

Yang, Binbin

MIMO (Multiple-Input Multiple-Output) technology offers new possibilities for wireless communication through transmission over multiple spatial channels, and enables linear increases in spectral efficiency as the number of the transmitting and receiving antennas increases. However, the physical implementation of such systems in compact devices encounters many physical constraints mainly from the design of multi-antennas. First, an antenna's bandwidth decreases dramatically as its electrical size reduces, a fact known as antenna Q limit; secondly, multiple antennas closely spaced tend to couple with each other, undermining MIMO performance. Though different MIMO antenna designs have been proposed in the literature, there is still a lack of a systematic design methodology and knowledge of performance limits. In this dissertation, we employ characteristic mode theory (CMT) as a powerful tool for MIMO antenna analysis and design. CMT allows us to examine each physical mode of the antenna aperture, and to access its many physical parameters without even exciting the antenna. For the first time, we propose efficient circuit models for MIMO antennas of arbitrary geometry using this modal decomposition technique. Those circuit models demonstrate the powerful physical insight of CMT for MIMO antenna modeling, and simplify MIMO antenna design problem to just the design of specific antenna structural modes and a modal feed network, making possible the separate design of antenna aperture and feeds. We therefore develop a feed-independent shape synthesis technique for optimization of broadband multi-mode apertures. Combining the shape synthesis and circuit modeling techniques for MIMO antennas, we propose a shape-first feed-next design methodology for MIMO antennas, and designed and fabricated two planar MIMO antennas, each occupying an aperture much smaller than the regular size of lambda/2 x lambda/2. Facilitated by the newly developed source formulation for antenna stored energy and recently reported work on antenna Q factor minimization, we extend the minimum Q limit to antennas of arbitrary geometry, and show that given an antenna aperture, any antenna design based on its substructure will result into minimum Q factors larger than or equal to that of the complete structure. This limit is much tighter than Chu's limit based on spherical modes, and applies to antennas of arbitrary geometry. Finally, considering the almost inevitable presence of mutual coupling effects within compact multiport antennas, we develop new decoupling networks (DN) and decoupling network synthesis techniques. An information-theoretic metric, information mismatch loss (Gammainfo), is defined for DN characterization. Based on this metric, the optimization of decoupling networks for broadband system performance is conducted, which demonstrates the limitation of the single-frequency decoupling techniques and room for improvement.

Laser beam micro-milling of nickel alloy: dimensional variations and RSM optimization of laser parameters

NASA Astrophysics Data System (ADS)

Ahmed, Naveed; Alahmari, Abdulrahman M.; Darwish, Saied; Naveed, Madiha

2016-12-01

Micro-channels are considered as the integral part of several engineering devices such as micro-channel heat exchangers, micro-coolers, micro-pulsating heat pipes and micro-channels used in gas turbine blades for aerospace applications. In such applications, a fluid flow is required to pass through certain micro-passages such as micro-grooves and micro-channels. The fluid flow characteristics (flow rate, turbulence, pressure drop and fluid dynamics) are mainly established based on the size and accuracy of micro-passages. Variations (oversizing and undersizing) in micro-passage's geometry directly affect the fluid flow characteristics. In this study, the micro-channels of several sizes are fabricated in well-known aerospace nickel alloy (Inconel 718) through laser beam micro-milling. The variations in geometrical characteristics of different-sized micro-channels are studied under the influences of different parameters of Nd:YAG laser. In order to have a minimum variation in the machined geometries of each size of micro-channel, the multi-objective optimization of laser parameters has been carried out utilizing the response surface methodology approach. The objective was set to achieve the targeted top widths and depths of micro-channels with minimum degree of taperness associated with the micro-channel's sidewalls. The optimized sets of laser parameters proposed for each size of micro-channel can be used to fabricate the micro-channels in Inconel 718 with minimum amount of geometrical variations.

Extinction-effective population index: incorporating life-history variations in population viability analysis.

PubMed

Fujiwara, Masami

2007-09-01

Viability status of populations is a commonly used measure for decision-making in the management of populations. One of the challenges faced by managers is the need to consistently allocate management effort among populations. This allocation should in part be based on comparison of extinction risks among populations. Unfortunately, common criteria that use minimum viable population size or count-based population viability analysis (PVA) often do not provide results that are comparable among populations, primarily because they lack consistency in determining population size measures and threshold levels of population size (e.g., minimum viable population size and quasi-extinction threshold). Here I introduce a new index called the "extinction-effective population index," which accounts for differential effects of demographic stochasticity among organisms with different life-history strategies and among individuals in different life stages. This index is expected to become a new way of determining minimum viable population size criteria and also complement the count-based PVA. The index accounts for the difference in life-history strategies of organisms, which are modeled using matrix population models. The extinction-effective population index, sensitivity, and elasticity are demonstrated in three species of Pacific salmonids. The interpretation of the index is also provided by comparing them with existing demographic indices. Finally, a measure of life-history-specific effect of demographic stochasticity is derived.

Maximum Likelihood and Minimum Distance Applied to Univariate Mixture Distributions.

ERIC Educational Resources Information Center

Wang, Yuh-Yin Wu; Schafer, William D.

This Monte-Carlo study compared modified Newton (NW), expectation-maximization algorithm (EM), and minimum Cramer-von Mises distance (MD), used to estimate parameters of univariate mixtures of two components. Data sets were fixed at size 160 and manipulated by mean separation, variance ratio, component proportion, and non-normality. Results…

AN EXPERIMENTAL ASSESSMENT OF MINIMUM MAPPING UNIT SIZE

EPA Science Inventory

Land-cover (LC) maps derived from remotely sensed data are often presented using a minimum mapping unit (MMU). The choice of a MMU that is appropriate for the projected use of a classification is important. The objective of this experiment was to determine the optimal MMU of a L...

Minimum-Impact Camping in the Front Woods.

ERIC Educational Resources Information Center

Schatz, Curt

1994-01-01

Minimum-impact camping techniques that can be applied to resident camp programs include controlling group size and behavior, designing camp sites, moving groups frequently, proper use of fires, proper disposal of food and human wastes, use of biodegradable soaps, and encouraging staff and camper awareness of impacts on the environment. (LP)

Evaluation of engineered foods for Closed Ecological Life Support System (CELSS)

NASA Technical Reports Server (NTRS)

Karel, M.

1981-01-01

A system of conversion of locally regenerated raw materials and of resupplied freeze-dried foods and ingredients into acceptable, safe and nutritious engineered foods is proposed. The first phase of the proposed research has the following objectives: (1) evaluation of feasibility of developing acceptable and reliable engineered foods from a limited selection of plants, supplemented by microbially produced nutrients and a minimum of dehydrated nutrient sources (especially those of animal origin); (2) evaluation of research tasks and specifications of research projects to adapt present technology and food science to expected space conditions (in particular, problems arising from unusual gravity conditions, problems of limited size and the isolation of the food production system, and the opportunities of space conditions are considered); (3) development of scenarios of agricultural production of plant and microbial systems, including the specifications of processing wastes to be recycled.

Thermodynamics constrains allometric scaling of optimal development time in insects.

PubMed

Dillon, Michael E; Frazier, Melanie R

2013-01-01

Development time is a critical life-history trait that has profound effects on organism fitness and on population growth rates. For ectotherms, development time is strongly influenced by temperature and is predicted to scale with body mass to the quarter power based on 1) the ontogenetic growth model of the metabolic theory of ecology which describes a bioenergetic balance between tissue maintenance and growth given the scaling relationship between metabolism and body size, and 2) numerous studies, primarily of vertebrate endotherms, that largely support this prediction. However, few studies have investigated the allometry of development time among invertebrates, including insects. Abundant data on development of diverse insects provides an ideal opportunity to better understand the scaling of development time in this ecologically and economically important group. Insects develop more quickly at warmer temperatures until reaching a minimum development time at some optimal temperature, after which development slows. We evaluated the allometry of insect development time by compiling estimates of minimum development time and optimal developmental temperature for 361 insect species from 16 orders with body mass varying over nearly 6 orders of magnitude. Allometric scaling exponents varied with the statistical approach: standardized major axis regression supported the predicted quarter-power scaling relationship, but ordinary and phylogenetic generalized least squares did not. Regardless of the statistical approach, body size alone explained less than 28% of the variation in development time. Models that also included optimal temperature explained over 50% of the variation in development time. Warm-adapted insects developed more quickly, regardless of body size, supporting the "hotter is better" hypothesis that posits that ectotherms have a limited ability to evolutionarily compensate for the depressing effects of low temperatures on rates of biological processes. The remaining unexplained variation in development time likely reflects additional ecological and evolutionary differences among insect species.

Application of Twin Beams in Mach-Zehnder Interferometer

NASA Technical Reports Server (NTRS)

Zhang, J. X.; Xie, C. D.; Peng, K. C.

1996-01-01

Using the twin beams generated from parametric amplifier to drive the two port of a Mach-Zehnder interferometer, it is shown that the minimum detectable optical phase shift can be largly reduced to the Heisenberg limit(1/n) which is far below the Shot Noise Limit(1/square root of n) the large gain limit. The dependence of the minimum detectable phase shift on parametric gain and the inefficient photodetectors has been discussed.

Support Minimized Inversion of Acoustic and Elastic Wave Scattering

NASA Astrophysics Data System (ADS)

Safaeinili, Ali

Inversion of limited data is common in many areas of NDE such as X-ray Computed Tomography (CT), Ultrasonic and eddy current flaw characterization and imaging. In many applications, it is common to have a bias toward a solution with minimum (L^2)^2 norm without any physical justification. When it is a priori known that objects are compact as, say, with cracks and voids, by choosing "Minimum Support" functional instead of the minimum (L^2)^2 norm, an image can be obtained that is equally in agreement with the available data, while it is more consistent with what is most probably seen in the real world. We have utilized a minimum support functional to find a solution with the smallest volume. This inversion algorithm is most successful in reconstructing objects that are compact like voids and cracks. To verify this idea, we first performed a variational nonlinear inversion of acoustic backscatter data using minimum support objective function. A full nonlinear forward model was used to accurately study the effectiveness of the minimized support inversion without error due to the linear (Born) approximation. After successful inversions using a full nonlinear forward model, a linearized acoustic inversion was developed to increase speed and efficiency in imaging process. The results indicate that by using minimum support functional, we can accurately size and characterize voids and/or cracks which otherwise might be uncharacterizable. An extremely important feature of support minimized inversion is its ability to compensate for unknown absolute phase (zero-of-time). Zero-of-time ambiguity is a serious problem in the inversion of the pulse-echo data. The minimum support inversion was successfully used for the inversion of acoustic backscatter data due to compact scatterers without the knowledge of the zero-of-time. The main drawback to this type of inversion is its computer intensiveness. In order to make this type of constrained inversion available for common use, work needs to be performed in three areas: (1) exploitation of state-of-the-art parallel computation, (2) improvement of theoretical formulation of the scattering process for better computation efficiency, and (3) development of better methods for guiding the non-linear inversion. (Abstract shortened by UMI.).

Field Study of Performance, Comfort, and Sizing of Two Variable-Speed Heat Pumps Installed in a Single 2-Story Residence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Munk, Jeffrey D; Odukomaiya, Adewale O; Gehl, Anthony C

2014-01-01

With the recent advancements in the application of variable-speed (VS) compressors to residential HVAC systems, opportunities are now available to size heat pumps (HPs) to more effectively meet heating and cooling loads in many of the climate zones in the US with limited use of inefficient resistance heat. This is in contrast to sizing guidance for traditional single-speed HPs that limits the ability to oversize with regard to cooling loads, because of risks of poor dehumidification during the cooling season and increased cycling losses. VS-drive HPs can often run at 30-40% of their rated cooling capacity to reduce cycling losses,more » and can adjust fan speed to provide better indoor humidity control. Detailed air-side performance data was collected on two VS-drive heat pumps installed in a single unoccupied research house in Knoxville, TN, a mixed-humid climate. One system provided space conditioning for the upstairs, while the other unit provided space conditioning for the downstairs. Occupancy was simulated by operating the lights, shower, appliances, other plug loads, etc. to simulate the sensible and latent loads imposed on the building space by internal electric loads and human occupants according to the Building America Research Benchmark (2008). The seasonal efficiency and energy use of the units are calculated. Annual energy use is compared to that of the single speed minimum efficiency HPs tested in the same house previously. Sizing of the units relative to the measured building load and manual J design load calculations is examined. The impact of the unit sizing with regards to indoor comfort is also evaluated.« less

[Variability patterns of nest construction, physiological state, and morphometric traits in honey bee].

PubMed

Es'kov, E K; Es'kova, M D

2014-01-01

High variability of cells size is used selectively for reproduction of working bees and drones. A decrease in both distance between cells and cells size themselves causes similar effects to body mass and morphometric traits of developing individuals. Adaptation of honey bees to living in shelters has led to their becoming tolerant to hypoxia. Improvement of ethological and physiological mechanisms of thermal regulation is associated with limitation of ecological valence and acquiring of stenothermic features by breed. Optimal thermal conditions for breed are limited by the interval 33-34.5 degrees C. Deviations of temperature by 3-4 degrees C beyond this range have minimum lethal effect at embryonic stage of development and medium effect at the stage of pre-pupa and pupa. Developing at the low bound of the vital range leads to increasing, while developing at the upper bound--to decreasing of body mass, mandibular and hypopharyngeal glands, as well as other organs, which, later, affects the variability of these traits during the adult stage of development. Eliminative and teratogenic efficiency of ecological factors that affect a breed is most often manifested in underdevelopment of wings. However, their size (in case of wing laminas formation). is characterized by relatively low variability and size-dependent asymmetry. Asymmetry variability of wings and other pair organs is expressed through realignment of size excess from right- to left-side one with respect to their increase. Selective elimination by those traits whose emerging probability increases as developmental conditions deviate from the optimal ones promotes restrictions on individual variability. Physiological mechanisms that facilitate adaptability enhancement under conditions of increasing anthropogenic contamination of eivironment and trophic substrates consumed by honey bees, arrear to be toxicants accumulation in rectum and crops' ability to absorb contaminants from nectar in course of its processing to honey.

Computational Investigation of Effects of Grain Size on Ballistic Performance of Copper

NASA Astrophysics Data System (ADS)

He, Ge; Dou, Yangqing; Guo, Xiang; Liu, Yucheng

2018-01-01

Numerical simulations were conducted to compare ballistic performance and penetration mechanism of copper (Cu) with four representative grain sizes. Ballistic limit velocities for coarse-grained (CG) copper (grain size ≈ 90 µm), regular copper (grain size ≈ 30 µm), fine-grained (FG) copper (grain size ≈ 890 nm), and ultrafine-grained (UG) copper (grain size ≈ 200 nm) were determined for the first time through the simulations. It was found that the copper with reduced grain size would offer higher strength and better ductility, and therefore renders improved ballistic performance than the CG and regular copper. High speed impact and penetration behavior of the FG and UG copper was also compared with the CG coppers strengthened by nanotwinned (NT) regions. The comparison results showed the impact and penetration resistance of UG copper is comparable to the CG copper strengthened by NT regions with the minimum twin spacing. Therefore, besides the NT-strengthened copper, the single phase copper with nanoscale grain size could also be a strong candidate material for better ballistic protection. A computational modeling and simulation framework was proposed for this study, in which Johnson-Cook (JC) constitutive model is used to predict the plastic deformation of Cu; the JC damage model is to capture the penetration and fragmentation behavior of Cu; Bao-Wierzbicki (B-W) failure criterion defines the material's failure mechanisms; and temperature increase during this adiabatic penetration process is given by the Taylor-Quinney method.

Approaching the Minimum Thermal Conductivity in Rhenium-Substituted Higher Manganese Silicides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xi; Girard, S. N.; Meng, F.

Higher manganese silicides (HMS) made of earth-abundant and non-toxic elements are regarded as promising p-type thermoelectric materials because their complex crystal structure results in low lattice thermal conductivity. It is shown here that the already low thermal conductivity of HMS can be reduced further to approach the minimum thermal conductivity via partial substitu- tion of Mn with heavier rhenium (Re) to increase point defect scattering. The solubility limit of Re in the obtained RexMn1 xSi1.8 is determined to be about x = 0.18. Elemental inhomogeneity and the formation of ReSi1.75 inclusions with 50 200 nm size are found within themore » HMS matrix. It is found that the power factor does not change markedly at low Re content of x 0.04 before it drops considerably at higher Re contents. Compared to pure HMS, the reduced lattice thermal conductivity in RexMn1 xSi1.8 results in a 25% increase of the peak figure of merit ZT to reach 0.57 0.08 at 800 K for x = 0.04. The suppressed thermal conductivity in the pure RexMn1 xSi1.8 can enable further investigations of the ZT limit of this system by exploring different impurity doping strategies to optimize the carrier concentration and power factor.« less

On the Relationship Between Spotless Days and the Sunspot Cycle: A Supplement

NASA Technical Reports Server (NTRS)

Wilson, Robert M.; Hathaway, David H.

2006-01-01

This study provides supplemental material to an earlier study concerning the relationship between spotless days and the sunspot cycle. Our previous study, Technical Publication (TP)-2005-213608 determined the timing and size of sunspot minimum and maximum for the new sunspot cycle, relative to the occurrence of the first spotless day during the declining phase of the old sunspot cycle and the last spotless day during the rising portion of the new cycle. Because the number of spotless days (NSD) rapidly increases as the cycle nears sunspot minimum and rapidly decreases thereafter, the size and timing of sunspot minimum and maximum might be more accurately determined using a higher threshold for comparison, rather than using the first and last spotless day occurrences. It is this aspect that is investigated more thoroughly in this TP.

Monte Carlo simulation of errors in the anisotropy of magnetic susceptibility - A second-rank symmetric tensor. [for grains in sedimentary and volcanic rocks

NASA Technical Reports Server (NTRS)

Lienert, Barry R.

1991-01-01

Monte Carlo perturbations of synthetic tensors to evaluate the Hext/Jelinek elliptical confidence regions for anisotropy of magnetic susceptibility (AMS) eigenvectors are used. When the perturbations are 33 percent of the minimum anisotropy, both the shapes and probability densities of the resulting eigenvector distributions agree with the elliptical distributions predicted by the Hext/Jelinek equations. When the perturbation size is increased to 100 percent of the minimum eigenvalue difference, the major axis of the 95 percent confidence ellipse underestimates the observed eigenvector dispersion by about 10 deg. The observed distributions of the principal susceptibilities (eigenvalues) are close to being normal, with standard errors that agree well with the calculated Hext/Jelinek errors. The Hext/Jelinek ellipses are also able to describe the AMS dispersions due to instrumental noise and provide reasonable limits for the AMS dispersions observed in two Hawaiian basaltic dikes. It is concluded that the Hext/Jelinek method provides a satisfactory description of the errors in AMS data and should be a standard part of any AMS data analysis.

High Tensile Strength Amalgams for In-Space Fabrication and Repair

NASA Technical Reports Server (NTRS)

Grugel, Richard N.

2006-01-01

Amalgams are well known for their use in dental practice as a tooth filling material. They have a number of useful attributes that include room temperature fabrication, corrosion resistance, dimensional stability, and very good compressive strength. These properties well serve dental needs but, unfortunately, amalgams have extremely poor tensile strength, a feature that severely limits other potential applications. Improved material properties (strength and temperature) of amalgams may have application to the freeform fabrication of repairs or parts that might be necessary during an extended space mission. Advantages would include, but are not limited to: the ability to produce complex parts, a minimum number of processing steps, minimum crew interaction, high yield - minimum wasted material, reduced gravity compatibility, minimum final finishing, safety, and minimum power consumption. The work presented here shows how the properties of amalgams can be improved by changing particle geometries in conjunction with novel engineering metals.

Tagging effects of passive integrated transponder and visual implant elastomer on the small-bodied white sands pupfish (Cyprinodon tularosa)

USGS Publications Warehouse

Peterson, Damon; Trantham, Randi B.; Trantham, Tulley G.; Caldwell, Colleen A.

2018-01-01

One of the greatest limiting factors of studies designed to obtain growth, movement, and survival in small-bodied fishes is the selection of a viable tag. The tag must be relatively small with respect to body size as to impart minimal sub-lethal effects on growth and mobility, as well as be retained throughout the life of the fish or duration of the study. Thus, body size of the model species becomes a major limiting factor; yet few studies have obtained empirical evidence of the minimum fish size and related tagging effects. The probability of surviving a tagging event was quantified in White Sands pupfish (Cyprinodon tularosa) across a range of sizes (19–60 mm) to address the hypothesis that body size predicts tagging survival. We compared tagging related mortality, individual taggers, growth, and tag retention in White Sands pupfish implanted with 8-mm passive integrated transponder (PIT), visual implant elastomer (VIE), and control (handled similarly, but no tag implantation) over a 75 d period. Initial body weight was a good predictor of the probability of survival in PIT- and VIE-tagged fish. As weight increased by 1 g, the fish were 4.73 times more likely to survive PIT-tag implantation compared to the control fish with an estimated suitable tagging size at 1.1 g (TL: 39.29 ± 0.41 mm). Likewise, VIE-tagged animals were 2.27 times more likely to survive a tagging event compared to the control group for every additional 1 g with an estimated size suitable for tagging of 0.9 g (TL: 36.9 ± 0.36 mm) fish. Growth rates of PIT- and VIE-tagged White Sands pupfish were similar to the control groups. This research validated two popular tagging methodologies in the White Sands pupfish, thus providing a valuable tool for characterizing vital rates in other small-bodied fishes.

Multi-image acquisition-based distance sensor using agile laser spot beam.

PubMed

Riza, Nabeel A; Amin, M Junaid

2014-09-01

We present a novel laser-based distance measurement technique that uses multiple-image-based spatial processing to enable distance measurements. Compared with the first-generation distance sensor using spatial processing, the modified sensor is no longer hindered by the classic Rayleigh axial resolution limit for the propagating laser beam at its minimum beam waist location. The proposed high-resolution distance sensor design uses an electronically controlled variable focus lens (ECVFL) in combination with an optical imaging device, such as a charged-coupled device (CCD), to produce and capture different laser spot size images on a target with these beam spot sizes different from the minimal spot size possible at this target distance. By exploiting the unique relationship of the target located spot sizes with the varying ECVFL focal length for each target distance, the proposed distance sensor can compute the target distance with a distance measurement resolution better than the axial resolution via the Rayleigh resolution criterion. Using a 30 mW 633 nm He-Ne laser coupled with an electromagnetically actuated liquid ECVFL, along with a 20 cm focal length bias lens, and using five spot images captured per target position by a CCD-based Nikon camera, a proof-of-concept proposed distance sensor is successfully implemented in the laboratory over target ranges from 10 to 100 cm with a demonstrated sub-cm axial resolution, which is better than the axial Rayleigh resolution limit at these target distances. Applications for the proposed potentially cost-effective distance sensor are diverse and include industrial inspection and measurement and 3D object shape mapping and imaging.

Localization of diffusion sources in complex networks with sparse observations

NASA Astrophysics Data System (ADS)

Hu, Zhao-Long; Shen, Zhesi; Tang, Chang-Bing; Xie, Bin-Bin; Lu, Jian-Feng

2018-04-01

Locating sources in a large network is of paramount importance to reduce the spreading of disruptive behavior. Based on the backward diffusion-based method and integer programming, we propose an efficient approach to locate sources in complex networks with limited observers. The results on model networks and empirical networks demonstrate that, for a certain fraction of observers, the accuracy of our method for source localization will improve as the increase of network size. Besides, compared with the previous method (the maximum-minimum method), the performance of our method is much better with a small fraction of observers, especially in heterogeneous networks. Furthermore, our method is more robust against noise environments and strategies of choosing observers.

Fabrication and Characterization of Woodpile Structures for Direct Laser Acceleration

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGuinness, C.; Colby, E.; England, R.J.

2010-08-26

An eight and nine layer three dimensional photonic crystal with a defect designed specifically for accelerator applications has been fabricated. The structures were fabricated using a combination of nanofabrication techniques, including low pressure chemical vapor deposition, optical lithography, and chemical mechanical polishing. Limits imposed by the optical lithography set the minimum feature size to 400 nm, corresponding to a structure with a bandgap centered at 4.26 {micro}m. Reflection spectroscopy reveal a peak in reflectivity about the predicted region, and good agreement with simulation is shown. The eight and nine layer structures will be aligned and bonded together to form themore » complete seventeen layer woodpile accelerator structure.« less

26 CFR 1.383-2 - Limitations on certain capital losses and excess credits in computing alternative minimum tax...

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 4 2010-04-01 2010-04-01 false Limitations on certain capital losses and excess credits in computing alternative minimum tax. [Reserved] 1.383-2 Section 1.383-2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Insolvency...

40 CFR Table 3 to Subpart Jjjjjj... - Operating Limits for Boilers With Emission Limits

Code of Federal Regulations, 2013 CFR

2013-07-01

... as defined in § 63.11237. 4. Dry sorbent or activated carbon injection control Maintain the 30-day rolling average sorbent or activated carbon injection rate at or above the minimum sorbent injection rate or minimum activated carbon injection rate as defined in § 63.11237. When your boiler operates at...

Gasdynamic Inlet Isolation in Rotating Detonation Engine

DTIC Science & Technology

2010-12-01

2D Total Variation Diminishing (TVD): Continuous Riemann Solver Minimum Dissipation: LHS & RHS Activate pressure switch : Supersonic Activate...Total Variation Diminishing (TVD) limiter: Continuous Riemann Solver Minimum Dissipation: LHS & RHS Activate pressure switch : Supersonic Activate...Continuous 94 Riemann Solver Minimum Dissipation: LHS & RHS Activate pressure switch : Supersonic Activate pressure gradient switch: Normal

14 CFR 135.221 - IFR: Alternate airport weather minimums.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false IFR: Alternate airport weather minimums... VFR/IFR Operating Limitations and Weather Requirements § 135.221 IFR: Alternate airport weather minimums. No person may designate an alternate airport unless the weather reports or forecasts, or any...

14 CFR 135.221 - IFR: Alternate airport weather minimums.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false IFR: Alternate airport weather minimums... VFR/IFR Operating Limitations and Weather Requirements § 135.221 IFR: Alternate airport weather minimums. No person may designate an alternate airport unless the weather reports or forecasts, or any...

14 CFR 135.221 - IFR: Alternate airport weather minimums.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false IFR: Alternate airport weather minimums... VFR/IFR Operating Limitations and Weather Requirements § 135.221 IFR: Alternate airport weather minimums. No person may designate an alternate airport unless the weather reports or forecasts, or any...

14 CFR 135.221 - IFR: Alternate airport weather minimums.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false IFR: Alternate airport weather minimums... VFR/IFR Operating Limitations and Weather Requirements § 135.221 IFR: Alternate airport weather minimums. No person may designate an alternate airport unless the weather reports or forecasts, or any...

14 CFR 135.221 - IFR: Alternate airport weather minimums.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false IFR: Alternate airport weather minimums... VFR/IFR Operating Limitations and Weather Requirements § 135.221 IFR: Alternate airport weather minimums. No person may designate an alternate airport unless the weather reports or forecasts, or any...

Some Observations on Damage Tolerance Analyses in Pressure Vessels

NASA Technical Reports Server (NTRS)

Raju, Ivatury S.; Dawicke, David S.; Hampton, Roy W.

2017-01-01

AIAA standards S080 and S081 are applicable for certification of metallic pressure vessels (PV) and composite overwrap pressure vessels (COPV), respectively. These standards require damage tolerance analyses with a minimum reliable detectible flaw/crack and demonstration of safe life four times the service life with these cracks at the worst-case location in the PVs and oriented perpendicular to the maximum principal tensile stress. The standards require consideration of semi-elliptical surface cracks in the range of aspect ratios (crack depth a to half of the surface length c, i.e., (a/c) of 0.2 to 1). NASA-STD-5009 provides the minimum reliably detectible standard crack sizes (90/95 probability of detection (POD) for several non-destructive evaluation (NDE) methods (eddy current (ET), penetrant (PT), radiography (RT) and ultrasonic (UT)) for the two limits of the aspect ratio range required by the AIAA standards. This paper tries to answer the questions: can the safe life analysis consider only the life for the crack sizes at the two required limits, or endpoints, of the (a/c) range for the NDE method used or does the analysis need to consider values within that range? What would be an appropriate method to interpolate 90/95 POD crack sizes at intermediate (a/c) values? Several procedures to develop combinations of a and c within the specified range are explored. A simple linear relationship between a and c is chosen to compare the effects of seven different approaches to determine combinations of aj and cj that are between the (a/c) endpoints. Two of the seven are selected for evaluation: Approach I, the simple linear relationship, and a more conservative option, Approach III. For each of these two Approaches, the lives are computed for initial semi-elliptic crack configurations in a plate subjected to remote tensile fatigue loading with an R-ratio of 0.1, for an assumed material evaluated using NASGRO (registered 4) version 8.1. These calculations demonstrate that for this loading, using Approach I and the initial detectable crack sizes at the (a/c) endpoints in 5009 specified for the ET and UT NDE methods, the smallest life is not at the two required limits of the (a/c) range, but rather is at an intermediate configuration in the range (a/c) of 0.4 to 0.6. Similar analyses using both Approach I and III with the initial detectable crack size at the (a/c) endpoints in 5009 for PT NDE showed the smallest life may be at an (a/c) endpoint or an intermediate (a/c), depending upon which Approach is used. As such, analyses that interrogate only the two (a/c) values of 0.2 and 1 may result in unconservative life predictions. The standard practice may need to be revised based on these results.

The effects of dispersal patterns on marine reserves: does the tail wag the dog?

PubMed

Lockwood, Dale R; Hastings, Alan; Botsford, Louis W

2002-05-01

The concept of marine reserves as a method of improving management of fisheries is gaining momentum. While the list of benefits from reserves is frequently promoted, precise formulations of theory to support reserve design are not fully developed. To determine the size of reserves and the distances between reserves an understanding of the requirements for persistence of local populations is required. Unfortunately, conditions for persistence are poorly characterized, as are the larval dispersal patterns on which persistence depends. With the current paucity of information regarding meroplanktonic larval transport processes, understanding the robustness of theoretical results to larval dispersal is of key importance. From this formulation a broad range of dispersal patterns are analyzed. Larval dispersal is represented by a probability distribution that defines the fraction of successful settlers from an arbitrary location, the origin of the distribution, to any other location along the coast. While the effects of specific dispersal patterns have been investigated for invasion processes, critical habitat size and persistence issues have generally been addressed with only one or two dispersal types. To that end, we formulate models based on integrodifference equations that are spatially continuous and temporally discrete. We consider a range of dispersal distributions from leptokurtic to platykurtic. The effect of different dispersal patterns is considered for a single isolated reserve of varying size receiving no external larvae, as well as multiple reserves with varying degrees of connectivity. While different patterns result in quantitative differences in persistence, qualitatively similar effects across all patterns are seen in both single- and multiple reserve models. Persistence in an isolated reserve requires a size that is approximately twice the mean dispersal distance and regardless of the dispersal pattern the population in a patch is not persistent if the reserve size is reduced to just the mean dispersal distance. With an idealized coastline structure consisting of an infinite line of equally spaced reserves separated by regions of coastline in which reproduction is nil, the relative settlement as a function of the fraction of coastline and size of reserve is qualitatively very similar over a broad range of dispersal patterns. The upper limit for the minimum fraction of coastline held in reserve is about 40%. As the fraction of coastline is reduced, the minimum size of reserve becomes no more than 1.25 times the mean dispersal distance.

G-NEST: A gene neighborhood scoring tool to identify co-conserved, co-expressed genes

USDA-ARS?s Scientific Manuscript database

In previous studies, gene neighborhoods--spatial clusters of co-expressed genes in the genome--have been defined using arbitrary rules such as requiring adjacency, a minimum number of genes, a fixed window size, or a minimum expression level. In the current study, we developed a Gene Neighborhood Sc...

Characterization of silicon-gate CMOS/SOS integrated circuits processed with ion implantation

NASA Technical Reports Server (NTRS)

Woo, D. S.

1982-01-01

The procedure used to generate MEBES masks and produce test wafers from the 10X Mann 1600 Pattern Generator Tape using existing CAD utility programs and the MEBES machine in the RCA Solid State Technology Center are described. The test vehicle used is the MSFC-designed SC102 Solar House Timing Circuit. When transforming the Mann 1600 tapes into MEBES tapes, extreme care is required in order to obtain accurate minimum linewidths when working with two different coding systems because the minimum grid sizes may be different for the two systems. The minimum grid sizes are 0.025 mil for MSFC Mann 1600 and 0.02 mil for MEBES. Some snapping to the next grid is therefore inevitable, and the results of this snapping effect are significant when submicron lines are present. However, no problem was noticed in the SC102 circuit because its minimum linewidth is 0.3 mil (7.6 microns). MEBES masks were fabricated and wafers were processed using the silicon-gate CMOS/SOS and aluminum-gate COS/MOS processing.

Free-Spinning Characteristics of a 1/24-Scale Model of the Grumman F11F-1 Airplane, TED No. NACA AD 395

NASA Technical Reports Server (NTRS)

Bowman, James S., Jr.

1955-01-01

An investigation is being conducted in the Langley 20-foot free-spinning tunnel on a 1/24-scale model of the Grumman F11F-1 airplane to determine spin and recovery characteristics and the minimum-size parachute required to satisfactorily terminate the spin in an emergency. Results obtained to date are presented herein. Test results indicate that it may be difficult to obtain an erect or inverted spin on the airplane, but, if a spin is obtained, the spin will be very oscillatory and recovery from the developed erect spin by rudder reversal may not be possible. The lateral controls will have no appreciable effect on recoveries from erect.spins. Recovery from the inverted spin by merely neutralizing the rudder will be satisfactory. After recoveries by rudder reversal and after recoveries from spins without control movement (no spins), the model oftentimes rolled very rapidly about the X-axis. Based on limited preliminary tests made in this investigation to make the model recover satisfactorily, it appears that canards near the nose of the airplane or differentially operated horizontal tails may be utilized to provide rapid recoveries. The parachute test results indicate that an 11-foot-diameter (laid-out-flat) parachute with a drag coefficient of 0.650 (based on the laid- out-flat diameter) and with a towline length equal to the wing span is the minimum-size parachute required to satisfactorily terminate an erect or inverted spin in an emergency.

42 CFR 84.205 - Facepiece test; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... respirator will be fitted to the faces of persons having varying facial shapes and sizes. (b) Where the applicant specifies a facepiece size or sizes for the respirator together with the approximate measurement..., pumping with a tire pump into a 28-liter (1 cubic-foot) container. (4) Each wearer shall not detect the...

Entropy considerations applied to shock unsteadiness in hypersonic inlets

NASA Astrophysics Data System (ADS)

Bussey, Gillian Mary Harding

The stability of curved or rectangular shocks in hypersonic inlets in response to flow perturbations can be determined analytically from the principle of minimum entropy. Unsteady shock wave motion can have a significant effect on the flow in a hypersonic inlet or combustor. According to the principle of minimum entropy, a stable thermodynamic state is one with the lowest entropy gain. A model based on piston theory and its limits has been developed for applying the principle of minimum entropy to quasi-steady flow. Relations are derived for analyzing the time-averaged entropy gain flux across a shock for quasi-steady perturbations in atmospheric conditions and angle as a perturbation in entropy gain flux from the steady state. Initial results from sweeping a wedge at Mach 10 through several degrees in AEDC's Tunnel 9 indicates the bow shock becomes unsteady near the predicted normal Mach number. Several curved shocks of varying curvature are compared to a straight shock with the same mean normal Mach number, pressure ratio, or temperature ratio. The present work provides analysis and guidelines for designing an inlet robust to off- design flight or perturbations in flow conditions an inlet is likely to face. It also suggests that inlets with curved shocks are less robust to off-design flight than those with straight shocks such as rectangular inlets. Relations for evaluating entropy perturbations for highly unsteady flow across a shock and limits on their use were also developed. The normal Mach number at which a shock could be stable to high frequency upstream perturbations increases as the speed of the shock motion increases and slightly decreases as the perturbation size increases. The present work advances the principle of minimum entropy theory by providing additional validity for using the theory for time-varying flows and applying it to shocks, specifically those in inlets. While this analytic tool is applied in the present work for evaluating the stability of shocks in hypersonic inlets, it can be used for an arbitrary application with a shock.

Minimum financial outlays for purchasing alcohol brands in the U.S.

PubMed

Albers, Alison Burke; DeJong, William; Naimi, Timothy S; Siegel, Michael; Shoaff, Jessica Ruhlman; Jernigan, David H

2013-01-01

Low alcohol prices are a potent risk factor for excessive drinking, underage drinking, and adverse alcohol-attributable outcomes. Presently, there is little reported information on alcohol prices in the U.S., in particular as it relates to the costs of potentially beneficial amounts of alcohol. To determine the minimum financial outlay necessary to purchase individual brands of alcohol using online alcohol price data from January through March 2012. The smallest container size and the minimum price at which that size beverage could be purchased in the U.S. in 2012 were determined for 898 brands of alcohol, across 17 different alcoholic beverage types. The analyses were conducted in March 2012. The majority of alcoholic beverage categories contain brands that can be purchased in the U.S. for very low minimum financial outlays. In the U.S., a wide variety of alcohol brands, across many types of alcohol, are available at very low prices. Given that both alcohol use and abuse are responsive to price, particularly among adolescents, the prevalence of low alcohol prices is concerning. Surveillance of alcohol prices and minimum pricing policies should be considered in the U.S. as part of a public health strategy to reduce excessive alcohol consumption and related harms. Copyright © 2013 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Minimum Financial Outlays for Purchasing Alcohol Brands in the U.S

PubMed Central

Albers, Alison Burke; DeJong, William; Naimi, Timothy S.; Siegel, Michael; Shoaff, Jessica Ruhlman; Jernigan, David H.

2012-01-01

Background Low alcohol prices are a potent risk factor for excessive drinking, underage drinking, and adverse alcohol-attributable outcomes. Presently, there is little reported information on alcohol prices in the U.S., in particular as it relates to the costs of potentially beneficial amounts of alcohol. Purpose To determine the minimum financial outlay necessary to purchase individual brands of alcohol using online alcohol price data from January through March 2012. Methods The smallest container size and the minimum price at which that size beverage could be purchased in the U.S. in 2012 were determined for 898 brands of alcohol, across 17 different alcoholic beverage types. The analyses were conducted in March 2012. Results The majority of alcoholic beverage categories contain brands that can be purchased in the U.S. for very low minimum financial outlays. Conclusions In the U.S., a wide variety of alcohol brands, across many types of alcohol, are available at very low prices. Given that both alcohol use and abuse are responsive to price, particularly among adolescents, the prevalence of low alcohol prices is concerning. Surveillance of alcohol prices and minimum pricing policies should be considered in the U.S. as part of a public health strategy to reduce excessive alcohol consumption and related harms. PMID:23253652

Small sample sizes in the study of ontogenetic allometry; implications for palaeobiology

PubMed Central

Vavrek, Matthew J.

2015-01-01

Quantitative morphometric analyses, particularly ontogenetic allometry, are common methods used in quantifying shape, and changes therein, in both extinct and extant organisms. Due to incompleteness and the potential for restricted sample sizes in the fossil record, palaeobiological analyses of allometry may encounter higher rates of error. Differences in sample size between fossil and extant studies and any resulting effects on allometric analyses have not been thoroughly investigated, and a logical lower threshold to sample size is not clear. Here we show that studies based on fossil datasets have smaller sample sizes than those based on extant taxa. A similar pattern between vertebrates and invertebrates indicates this is not a problem unique to either group, but common to both. We investigate the relationship between sample size, ontogenetic allometric relationship and statistical power using an empirical dataset of skull measurements of modern Alligator mississippiensis. Across a variety of subsampling techniques, used to simulate different taphonomic and/or sampling effects, smaller sample sizes gave less reliable and more variable results, often with the result that allometric relationships will go undetected due to Type II error (failure to reject the null hypothesis). This may result in a false impression of fewer instances of positive/negative allometric growth in fossils compared to living organisms. These limitations are not restricted to fossil data and are equally applicable to allometric analyses of rare extant taxa. No mathematically derived minimum sample size for ontogenetic allometric studies is found; rather results of isometry (but not necessarily allometry) should not be viewed with confidence at small sample sizes. PMID:25780770

The Effect of Minimum Wage Rates on High School Completion

ERIC Educational Resources Information Center

Warren, John Robert; Hamrock, Caitlin

2010-01-01

Does increasing the minimum wage reduce the high school completion rate? Previous research has suffered from (1. narrow time horizons, (2. potentially inadequate measures of states' high school completion rates, and (3. potentially inadequate measures of minimum wage rates. Overcoming each of these limitations, we analyze the impact of changes in…

The minimum control authority of a system of actuators with applications to Gravity Probe-B

NASA Technical Reports Server (NTRS)

Wiktor, Peter; Debra, Dan

1991-01-01

The forcing capabilities of systems composed of many actuators are analyzed in this paper. Multiactuator systems can generate higher forces in some directions than in others. Techniques are developed to find the force in the weakest direction. This corresponds to the worst-case output and is defined as the 'minimum control authority'. The minimum control authority is a function of three things: the actuator configuration, the actuator controller and the way in which the output of the system is limited. Three output limits are studied: (1) fuel-flow rate, (2) power, and (3) actuator output. The three corresponding actuator controllers are derived. These controllers generate the desired force while minimizing either fuel flow rate, power or actuator output. It is shown that using the optimal controller can substantially increase the minimum control authority. The techniques for calculating the minimum control authority are applied to the Gravity Probe-B spacecraft thruster system. This example shows that the minimum control authority can be used to design the individual actuators, choose actuator configuration, actuator controller, and study redundancy.

The Effect Of Pixel Size On The Detection Rate Of Early Pulmonary Sarcoidosis In Digital Chest Radiographic Systems

NASA Astrophysics Data System (ADS)

MacMahon, Heber; Vyborny, Carl; Powell, Gregory; Doi, Kunio; Metz, Charles E.

1984-08-01

In digital radiography the pixel size used determines the potential spatial resolution of the system. The need for spatial resolution varies depending on the subject matter imaged. In many areas, including the chest, the minimum spatial resolution requirements have not been determined. Sarcoidosis is a disease which frequently causes subtle interstitial infiltrates in the lungs. As the initial step in an investigation designed to determine the minimum pixel size required in digital chest radiographic systems, we have studied 1 mm pixel digitized images on patients with early pulmonary sarcoidosis. The results of this preliminary study suggest that neither mild interstitial pulmonary infiltrates nor other abnormalities such as pneumothoraces may be detected reliably with 1 mm pixel digital images.

PAVENET OS: A Compact Hard Real-Time Operating System for Precise Sampling in Wireless Sensor Networks

NASA Astrophysics Data System (ADS)

Saruwatari, Shunsuke; Suzuki, Makoto; Morikawa, Hiroyuki

The paper shows a compact hard real-time operating system for wireless sensor nodes called PAVENET OS. PAVENET OS provides hybrid multithreading: preemptive multithreading and cooperative multithreading. Both of the multithreading are optimized for two kinds of tasks on wireless sensor networks, and those are real-time tasks and best-effort ones. PAVENET OS can efficiently perform hard real-time tasks that cannot be performed by TinyOS. The paper demonstrates the hybrid multithreading realizes compactness and low overheads, which are comparable to those of TinyOS, through quantitative evaluation. The evaluation results show PAVENET OS performs 100 Hz sensor sampling with 0.01% jitter while performing wireless communication tasks, whereas optimized TinyOS has 0.62% jitter. In addition, PAVENET OS has a small footprint and low overheads (minimum RAM size: 29 bytes, minimum ROM size: 490 bytes, minimum task switch time: 23 cycles).

Assessment of codes, by-laws and regulations relating to air wells in building design

NASA Astrophysics Data System (ADS)

Fadzil, Sharifah Fairuz Syed; Karamazaman, Nazli

2017-10-01

Codes and by-laws concerning air well design (for buildings and lavatories) in Malaysia has been established in the Malaysian Uniform Building By-Laws UBBL number 40 (1) and (2) since the 1980s. Wells are there to fulfill the ventilation and daylighting requirements. The minimum well area according to building storey height are compared between UBBL and the Singapore's well requirements from the Building Construction Authority BCA. A visual and graphical representation (with schematics building and well diagrams drawn to scale) of the minimum well sizes and dimensions is given. It can be seen that if the minimum requirement of well size is used for buildings above 8 storeys high, a thin well resulted which is not proportionate to the building height. A proposed dimension is graphed and given to be used in the UBBL which translated to graphics (3 dimensional buildings drawn to scale) created a much better well proportion.

The quality of the reported sample size calculations in randomized controlled trials indexed in PubMed.

PubMed

Lee, Paul H; Tse, Andy C Y

2017-05-01

There are limited data on the quality of reporting of information essential for replication of the calculation as well as the accuracy of the sample size calculation. We examine the current quality of reporting of the sample size calculation in randomized controlled trials (RCTs) published in PubMed and to examine the variation in reporting across study design, study characteristics, and journal impact factor. We also reviewed the targeted sample size reported in trial registries. We reviewed and analyzed all RCTs published in December 2014 with journals indexed in PubMed. The 2014 Impact Factors for the journals were used as proxies for their quality. Of the 451 analyzed papers, 58.1% reported an a priori sample size calculation. Nearly all papers provided the level of significance (97.7%) and desired power (96.6%), and most of the papers reported the minimum clinically important effect size (73.3%). The median (inter-quartile range) of the percentage difference of the reported and calculated sample size calculation was 0.0% (IQR -4.6%;3.0%). The accuracy of the reported sample size was better for studies published in journals that endorsed the CONSORT statement and journals with an impact factor. A total of 98 papers had provided targeted sample size on trial registries and about two-third of these papers (n=62) reported sample size calculation, but only 25 (40.3%) had no discrepancy with the reported number in the trial registries. The reporting of the sample size calculation in RCTs published in PubMed-indexed journals and trial registries were poor. The CONSORT statement should be more widely endorsed. Copyright © 2016 European Federation of Internal Medicine. Published by Elsevier B.V. All rights reserved.

Practical implications of theoretical consideration of capsule filling by the dosator nozzle system.

PubMed

Jolliffe, I G; Newton, J M

1982-05-01

Eight lactose size fractions with mean particle sizes ranging from 15.6 to 155.2 micrometers were characterized by their failure properties using a Jenike shear cell. The effective angle of internal friction was found to be constant for all size fractions, with a mean value of 36.2 degrees. Jenike flow factors could only be obtained for the two most cohesive size fractions presumably due to limitations of the shear cell. Angles of wall friction, phi, were determined for all size fractions on face ground and turned stainless steel surfaces. These decreased with increasing particle size up to around 40 micrometers, above which they became effectively constant for both surfaces. The rougher turned plate gave consistently higher values of phi for each particle size. Simple retention experiments with a dosator nozzle and a range of powder bed bulk densities showed good retention was possible only up to a particle size of around 40 micrometers. Retention was difficult or impossible above this size. Values of phi were applied to equations derived in the theoretical approach described previously (Jolliffe et al 1980). This showed that the strength required within a powder to ensure arching increases with increasing particle size up to around 40 micrometers. Above this size, this strength requirement becomes constant. This is related to the powder retention observations. Finally, the failure data was used to calculate the minimum compressive stresses required to ensure powder retention within the dosator nozzle, by employing the equations described by Jolliffe et al (1980). This suggested that, as powders became more free flowing, a larger compressive stress is necessary and that the angle of wall friction should be lower to ensure stress is transmitted to the arching zone.

Walleye population and fishery responses after elimination of legal harvest on Escanaba Lake, Wisconsin

USGS Publications Warehouse

Haglund, Justin M.; Isermann, Daniel A.; Sass, Greg G.

2016-01-01

Implementing harvest regulations to eliminate or substantially reduce (≥90%) the exploitation of Walleyes Sander vitreus in recreational fisheries may increase population size structure, but these measures also could reduce angler effort because many Walleye anglers are harvest oriented. We analyzed data collected during 1995–2015 to determine whether Walleye population and fishery metrics in Escanaba Lake, Wisconsin, changed after a minimum TL limit of 71 cm with a one-fish daily bag limit was implemented in 2003. This change eliminated the legal harvest of Walleyes after several decades during which annual exploitation averaged 34%. We detected a significant increase in the loge density of adult females after the regulation change, but the loge density of all adults and adult males did not differ between periods. Mean TL of adult males was significantly greater after the regulation change, but the mean TL of females and the proportional size distribution of preferred-length fish (≥51 cm TL) were similar between periods. Sex-specific mean TLs at age 5 did not differ between periods. Loge density of age-0 Walleyes did not change after 2003, but variation in age-0 density was lower. Total angler effort and the effort for anglers targeting Walleyes were significantly lower (35% and 60% declines, respectively) after the regulation change, whereas catch rates for both angler categories did not differ between periods. Our results suggest that implementing highly restrictive regulations that greatly reduce or eliminate legal harvest will not always increase angler catch rates and population size structure. Highly restrictive regulations may also deter anglers from using a fishery when many other fisheries are available. Our findings are useful for fishery managers who may work with anglers holding the belief that lower exploitation is a potential remedy for low Walleye size structure, even when density and growth suggest that there is limited potential for improvement.

Design and fabrication of sub-wavelength annular apertures on fiber tip for femtosecond laser machining

NASA Astrophysics Data System (ADS)

Tung, Yen-Chun; Chung, Ming-Han; Sung, I.-Hui; Lee, Chih-Kung

2014-03-01

Adopting optical technique to pursue micromachining must make a compromise between the focal spot sizes the depth of focus. The focal spot size determines the minimum features can be fabricated. On the other hand, the depth of focus influences the ease of alignment in positioning the fabrication light beam. A typical approach to bypass the diffraction limit is to adopt the near-field approach, which has spot size in the range of the optical fiber tip. However, the depth of focus of the emitted light beam will be limited to tens of nanometers in most cases, which posts a difficult challenge to control the distance between the optical fiber tip and the sample to be machined optically. More specifically, problems remained in this machining approach, which include issues such as residue induced by laser ablation tends to deposit near the optical fiber tip and leads to loss of coupling efficiency. We proposed a method based on illuminating femtosecond laser through a sub-wavelength annular aperture on metallic film so as to produce Bessel light beam of sub-wavelength while maintaining large depth of focus first. To further advance the ease of use in one such system, producing sub-wavelength annular aperture on a single mode optical fiber head with sub-wavelength focusing ability is detailed. It is shown that this method can be applied in material machining with an emphasis to produce high aspect ratio structure. Simulations and experimental results are presented in this paper.

How Low Can You Go? The Importance of Quantifying Minimum Generation Levels for Renewable Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denholm, Paul L; Brinkman, Gregory L; Mai, Trieu T

One of the significant limitations of solar and wind deployment is declining value caused by the limited correlation of renewable energy supply and electricity demand as well as limited flexibility of the power system. Limited flexibility can result from thermal and hydro plants that cannot turn off or reduce output due to technical or economic limits. These limits include the operating range of conventional thermal power plants, the need for process heat from combined heat and power plants, and restrictions on hydro unit operation. To appropriately analyze regional and national energy policies related to renewable deployment, these limits must bemore » accurately captured in grid planning models. In this work, we summarize data sources and methods for U.S. power plants that can be used to capture minimum generation levels in grid planning tools, such as production cost models. We also provide case studies for two locations in the U.S. (California and Texas) that demonstrate the sensitivity of variable generation (VG) curtailment to grid flexibility assumptions which shows the importance of analyzing (and documenting) minimum generation levels in studies of increased VG penetration.« less

The role of carbon solubility in Fe-C nano-clusters on the growth of small single-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Curtarolo, Stefano; Awasthy, Neha; Setyawan, Wahyu; Mora, Elena; Tokune, Toshio; Bolton, Kim; Harutyunyan, Avetik

2008-03-01

Various diameters of alumina-supported Fe catalysts are used to grow single-walled carbon nanotubes (SWCNTs) with chemical vapor decomposition. We find that the reduction of the catalyst size requires an increase of the minimum temperature necessary for the growth. We address this phenomenon in terms of solubility of C in Fe nanoclusters and, by using first principles calculations, we devise a simple model to predict the behavior of the phases competing for stability in Fe-C nanoclusters at low temperature. We show that, as a function particles size, there are three scenarios compatible with steady state-, limited- and no-growth of SWCNTs, corresponding to unaffected, reduced and no solubility of C in the particles. The result raises previously unknown concerns about the growth feasibility of small and very-long SWCNTs within the current Fe CVD technology, and suggests new strategies in the search of better catalysts. Research supported by Honda R.I. and NSF.

Yearly simulation of a solar-aided R22-DEGDME absorption heat pump system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ileri, A.

1995-12-31

The performance of a solar-aided R22-DEGDME absorption heat pump system designed for 100 kW cooling capacity is investigated by a computer simulation using hourly data for Ankara. In summer the generator, and in winter the evaporator, receives solar energy while the remaining demands are met by auxiliary heaters. When needed, these boost the temperature of the water from the storage tank to the minimum allowable levels which are determined as 20{degree}C in winter and over 80{degree}C in summer. The system performance, judged by the fraction of the load supplied from solar energy, is affected mostly from the climate, source temperaturemore » limit, collector type and area but little from storage tank size, for the sizes and configuration under investigation. With 400 m{sup 2} of high efficiency collectors, the solar energy supplied 38% of the demand in winter and 91% of the demand in summer. 22 refs., 2 figs., 6 tabs.« less

[The certification of advanced therapy medicinal products. A quality label for product development in small and medium-sized enterprises].

PubMed

Berger, A; Schüle, S; Flory, E

2011-07-01

Advanced therapy medicinal products (ATMPs) are gene therapy, cell therapy, and tissue engineered products. To gain access to the market within the European Union, ATMPs must be authorized by the European Commission (EC). Especially for small and medium-sized enterprises (SMEs), the European centralized procedure of marketing authorization that is conducted by the European Medicines Agency (EMA) constitutes a major challenge, because SMEs often have little experience with regulatory procedures and many have limited financial possibilities. To tackle these challenges, a certification procedure exclusively for SMEs and their ATMP development was introduced by the EC. Independently from a marketing authorization application, development and/or production processes can be certified. An issued certificate demonstrates that the respective process meets the current regulatory and scientific requirements of the EMA, representing a valuable milestone for putative investors and licensees. This article highlights the background, the detailed procedure, the minimum requirements, as well as the costs of certification, while giving further noteworthy guidance for interested parties.

Slicing cluster mass functions with a Bayesian razor

NASA Astrophysics Data System (ADS)

Sealfon, C. D.

2010-08-01

We apply a Bayesian ``razor" to forecast Bayes factors between different parameterizations of the galaxy cluster mass function. To demonstrate this approach, we calculate the minimum size N-body simulation needed for strong evidence favoring a two-parameter mass function over one-parameter mass functions and visa versa, as a function of the minimum cluster mass.

Glasses-free large size high-resolution three-dimensional display based on the projector array

NASA Astrophysics Data System (ADS)

Sang, Xinzhu; Wang, Peng; Yu, Xunbo; Zhao, Tianqi; Gao, Xing; Xing, Shujun; Yu, Chongxiu; Xu, Daxiong

2014-11-01

Normally, it requires a huge amount of spatial information to increase the number of views and to provide smooth motion parallax for natural three-dimensional (3D) display similar to real life. To realize natural 3D video display without eye-wears, a huge amount of 3D spatial information is normal required. However, minimum 3D information for eyes should be used to reduce the requirements for display devices and processing time. For the 3D display with smooth motion parallax similar to the holographic stereogram, the size the virtual viewing slit should be smaller than the pupil size of eye at the largest viewing distance. To increase the resolution, two glass-free 3D display systems rear and front projection are presented based on the space multiplexing with the micro-projector array and the special designed 3D diffuse screens with the size above 1.8 m× 1.2 m. The displayed clear depths are larger 1.5m. The flexibility in terms of digitized recording and reconstructed based on the 3D diffuse screen relieves the limitations of conventional 3D display technologies, which can realize fully continuous, natural 3-D display. In the display system, the aberration is well suppressed and the low crosstalk is achieved.

40 CFR Table 3 to Subpart Ddddd of... - Operating Limits for Boilers and Process Heaters With Mercury Emission Limits and Boilers and...

Code of Federal Regulations, 2010 CFR

2010-07-01

... minimum pressure drop and liquid flow-rate at or above the operating levels established during the... leak detection system alarm does not sound more than 5 percent of the operating time during a 6-month... control Maintain the minimum sorbent or carbon injection rate at or above the operating levels established...

40 CFR Table 3 to Subpart Ddddd of... - Operating Limits for Boilers and Process Heaters With Mercury Emission Limits and Boilers and...

Code of Federal Regulations, 2011 CFR

2011-07-01

... minimum pressure drop and liquid flow-rate at or above the operating levels established during the... leak detection system alarm does not sound more than 5 percent of the operating time during a 6-month... control Maintain the minimum sorbent or carbon injection rate at or above the operating levels established...

Post-stratified estimation: with-in strata and total sample size recommendations

Treesearch

James A. Westfall; Paul L. Patterson; John W. Coulston

2011-01-01

Post-stratification is used to reduce the variance of estimates of the mean. Because the stratification is not fixed in advance, within-strata sample sizes can be quite small. The survey statistics literature provides some guidance on minimum within-strata sample sizes; however, the recommendations and justifications are inconsistent and apply broadly for many...

Coupled changes in sand grain size and sand transport driven by changes in the upstream supply of sand in the Colorado River: relative importance of changes in bed-sand grain size and bed-sand area

USGS Publications Warehouse

Topping, D.J.; Rubin, D.M.; Melis, T.S.

2007-01-01

Sand transport in the Colorado River in Marble and Grand canyons was naturally limited by the upstream supply of sand. Prior to the 1963 closure of Glen Canyon Dam, the river exhibited the following four effects of sand supply limitation: (1) hysteresis in sediment concentration, (2) hysteresis in sediment grain size coupled to the hysteresis in sediment concentration, (3) production of inversely graded flood deposits, and (4) development or modification of a lag between the time of a flood peak and the time of either maximum or minimum (depending on reach geometry) bed elevation. Construction and operation of the dam has enhanced the degree to which the first two of these four effects are evident, and has not affected the degree to which the last two effects of sand supply limitation are evident in the Colorado River in Marble and Grand canyons. The first three of the effects involve coupled changes in suspended-sand concentration and grain size that are controlled by changes in the upstream supply of sand. During tributary floods, sand on the bed of the Colorado River fines; this causes the suspended sand to fine and the suspended-sand concentration to increase, even when the discharge of water remains constant. Subsequently, the bed is winnowed of finer sand, the suspended sand coarsens, and the suspended-sand concentration decreases independently of discharge. Also associated with these changes in sand supply are changes in the fraction of the bed that is covered by sand. Thus, suspended-sand concentration in the Colorado River is likely regulated by both changes in the bed-sand grain size and changes in the bed-sand area. A physically based flow and suspended-sediment transport model is developed, tested, and applied to data from the Colorado River to evaluate the relative importance of changes in the bed-sand grain size and changes in the bed-sand area in regulating suspended-sand concentration. Although the model was developed using approximations for steady, uniform flow, and other simplifications that are not met in the Colorado River, the results nevertheless support the idea that changes in bed-sand grain size are much more important than changes in bed-sand area in regulating the concentration of suspended sand.

Effect of ranibizumab on high-speed indocyanine green angiography and minimum intensity projection optical coherence tomography findings in neovascular age-related macular degeneration.

PubMed

Nicholson, Benjamin P; Nigam, Divya; Toy, Brian; Stetson, Paul F; Agrón, Elvira; Jacobs-El, Naima; Cunningham, Denise; Cukras, Catherine; Wong, Wai; Wiley, Henry; Chew, Emily; Ferris, Frederick; Meyerle, Catherine B

2015-01-01

The purpose of this 1-year prospective study was to investigate how induction/pro re nata ranibizumab intravitreal treatment of eyes with neovascular age-related macular degeneration affects the anatomy of choroidal neovascularization (CNV) and the overlying outer retinal tissue. High-speed indocyanine green (HS-ICG) angiography measurements provided quantification of the CNV size in 60 patients followed for 1 year. Minimum intensity projection optical coherence tomography (MinIP OCT), a novel algorithm assessing minimum optical intensity between the internal limiting membrane and retinal pigment epithelium, measured the area of outer retinal disruption overlying the CNV. Fluorescein angiography was also assessed to evaluate late retinal leakage. After 1 year, the mean area of CNV measured with indocyanine green angiography decreased by 5.8%. The mean area of MinIP OCT of outer retinal disruption overlying the CNV decreased by 4.2%. Mean area of fluorescein angiography leakage decreased by 6.3%. Both the area of outer retinal disruption measured with MinIP OCT and the area of leakage on fluorescein angiography typically exceeded the area of CNV on indocyanine green angiography at baseline and 1 year. Choroidal neovascularization treated with induction/pro re nata intravitreal ranibizumab for 1 year essentially remained static. Minimum intensity projection optical coherence tomography suggests that the area of outer retinal disruption overlying the CNV may be greater than the CNV itself and often correlates with the leakage area on fluorescein angiography. Additionally, there was minimal change in the area of outer retinal disruption on MinIP OCT even when fluid resolved. Measurements of the extent of CNV lesions based on indocyanine green angiography and MinIP OCT may provide useful outcome variables to help assess the CNV complex longitudinally and warrant further validation.

25 CFR 542.42 - What are the minimum internal control standards for internal audit for Tier C gaming operations?

Code of Federal Regulations, 2010 CFR

2010-04-01

... reconciliation process; (ii) Pull tabs, including but not limited to, statistical records, winner verification... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum internal control standards for... COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.42 What are...

Personalized hip implants manufacturing and testing

NASA Astrophysics Data System (ADS)

Croitoru, A. Sorin Mihai; Pacioga, B. Adrian; Comsa, C. Stanca

2017-09-01

Two models of Ti6Al4V personalized femoral stems for hip replacement have been designed and laser sintered with different sizes of fenestrated architecture that mimics the natural structure of bone, ensuring postoperative bone ingrowth and increasing the elasticity of the entire structure. They were tested statically and dynamically versus a commercial femoral stem. Mechanical tests were performed in order to determine the fatigue limit using the Locati method. The tests were conducted in a thermostatic bath (37°±1°) with the implants immersed in distilled water salted solution 0.91%. For probe embedment poly-methyl methacrylate (PMMA) was used. The characteristic curves of the two personalized fenestrated implants reveal an elastic behaviour by their nonlinear appearance. After dynamic tests an inverse relationship between displacements obtained in the static tests and the fatigue limit was observed. Large fenestrations conferred the desired elasticity to the implant, but contributed to a life service reduction. The fatigue limit for both implants was much above the minimum value specified by ISO 7602: 2010, so both models can be safely used in the medical practice, leading to increased life service of implants.

Frost damage in citric and olive production as the result of climate degradation

NASA Astrophysics Data System (ADS)

Saa Requejo, A.; Díaz Alvarez, M. C.; Tarquis, A. M.; Burgaz Moreno, F.; Garcia Moreno, R.

2009-04-01

Low temperature is one of the chief limiting factors in plant distribution. Freezing temperature shortens the growing season and may lower the yield and quality of any number of fruit crops. Minimum temperatures records for the Spanish region of Murcia were studied as limiting factor in fruit production. An analysis of temperature series since 1935 showed that the range of the absolute minimum temperatures (Tmin) on frost days in the target year, namely -0.5 °C to -4.0°C, was statistically similar to the range recorded in 1993, while the mean minimum temperatures (tmin) were found to have risen. The historical series also showed the mean minimum temperatures (tmin) to have increased, however. Through 1985, tmin ranged from 4.0 to -2.0 °C, depending on the area, while these limits shifted in more recent years to 7.0 - 0.5 °C. This increase in mean temperature produced that the frost episodes in March 2004 was considered by lemon, mandarin and olive producers as the worst in many years for frost damage since the minimum temperature was reached in a more sensitive phenological stage, despite the statistical evidence that similar freezing temperatures had been reached on similar dates in other years.

Ontogenetic prey size selection in snakes: predator size and functional limitations to handling minimum prey sizes.

PubMed

Hampton, Paul M

2018-02-01

As body size increases, some predators eliminate small prey from their diet exhibiting an ontogenetic shift toward larger prey. In contrast, some predators show a telescoping pattern of prey size in which both large and small prey are consumed with increasing predator size. To explore a functional explanation for the two feeding patterns, I examined feeding effort as both handling time and number of upper jaw movements during ingestion of fish of consistent size. I used a range of body sizes from two snake species that exhibit ontogenetic shifts in prey size (Nerodia fasciata and N. rhombifer) and a species that exhibits telescoping prey size with increased body size (Thamnophis proximus). For the two Nerodia species, individuals with small or large heads exhibited greater difficulty in feeding effort compared to snakes of intermediate size. However, for T. proximus measures of feeding effort were negatively correlated with head length and snout-vent length (SVL). These data indicate that ontogenetic shifters of prey size develop trophic morphology large enough that feeding effort increases for disproportionately small prey. I also compared changes in body size among the two diet strategies for active foraging snake species using data gleaned from the literature to determine if increased change in body size and thereby feeding morphology is observable in snakes regardless of prey type or foraging habitat. Of the 30 species sampled from literature, snakes that exhibit ontogenetic shifts in prey size have a greater magnitude of change in SVL than species that have telescoping prey size patterns. Based upon the results of the two data sets above, I conclude that ontogenetic shifts away from small prey occur in snakes due, in part, to growth of body size and feeding structures beyond what is efficient for handling small prey. Copyright © 2017. Published by Elsevier GmbH.

Evaluation of rules to distinguish unique female grizzly bears with cubs in Yellowstone

USGS Publications Warehouse

Schwartz, C.C.; Haroldson, M.A.; Cherry, S.; Keating, K.A.

2008-01-01

The United States Fish and Wildlife Service uses counts of unduplicated female grizzly bears (Ursus arctos) with cubs-of-the-year to establish limits of sustainable mortality in the Greater Yellowstone Ecosystem, USA. Sightings are dustered into observations of unique bears based on an empirically derived rule set. The method has never been tested or verified. To evaluate the rule set, we used data from radiocollared females obtained during 1975-2004 to simulate populations under varying densities, distributions, and sighting frequencies. We tested individual rules and rule-set performance, using custom software to apply the rule-set and duster sightings. Results indicated most rules were violated to some degree, and rule-based dustering consistently underestimated the minimum number of females and total population size derived from a nonparametric estimator (Chao2). We conclude that the current rule set returns conservative estimates, but with minor improvements, counts of unduplicated females-with-cubs can serve as a reasonable index of population size useful for establishing annual mortality limits. For the Yellowstone population, the index is more practical and cost-effective than capture-mark-recapture using either DNA hair snagging or aerial surveys with radiomarked bears. The method has useful application in other ecosystems, but we recommend rules used to distinguish unique females be adapted to local conditions and tested.

A simple robust method for synthesis of metallic copper nanoparticles of high antibacterial potency against E. coli

NASA Astrophysics Data System (ADS)

Chatterjee, Arijit Kumar; Sarkar, Raj Kumar; Prasun Chattopadhyay, Asoke; Aich, Pulakesh; Chakraborty, Ruchira; Basu, Tarakdas

2012-03-01

A method for preparation of copper nanoparticles (Cu-NPs) was developed by simple reduction of CuCl2 in the presence of gelatin as a stabilizer and without applying stringent conditions like purging with nitrogen. The NPs were characterized by spectrophotometry, dynamic light scattering, x-ray diffraction, transmission electron microscopy, atomic force microscopy and x-ray photoelectron spectroscopy. The particles were about 50-60 nm in size and highly stable. The antibacterial activity of this Cu-NP on Gram-negative Escherichia coli was demonstrated by the methods of agar plating, flow cytometry and phase contrast microscopy. The minimum inhibitory concentration (3.0 µg ml-1), minimum bactericidal concentration (7.5 µg ml-1) and susceptibility constant (0.92) showed that this Cu-NP is highly effective against E. coli at a much lower concentration than that reported previously. Treatment with Cu-NPs made E. coli cells filamentous. The higher the concentration of Cu-NPs, the greater the population of filamentous cells; average filament size varied from 7 to 20 µm compared to the normal cell size of ˜2.5 µm. Both filamentation and killing of cells by Cu-NPs (7.5 µg ml-1) also occurred in an E. coli strain resistant to multiple antibiotics. Moreover, an antibacterial effect of Cu-NPs was also observed in Gram-positive Bacillus subtilis and Staphylococcus aureus, for which the values of minimum inhibitory concentration and minimum bactericidal concentration were close to that for E. coli.

50 CFR 648.143 - Minimum sizes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... retain black sea bass in or from U.S. waters of the western Atlantic Ocean from 35′ 15.3 N. Lat., the... size for black sea bass is 12.5 inches (31.75 cm) TL for all vessels that do not qualify for a...

50 CFR 648.127 - Framework adjustments to management measures.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., FMP Monitoring Committee composition and process, description and identification of essential fish... additions to management measures must come from one or more of the following categories: Minimum fish size, maximum fish size, gear restrictions, gear restricted areas, gear requirements or prohibitions, permitting...

Minimum-Time and Vibration Avoidance Attitude Maneuver for Spacecraft with Torque and Momentum Limit Constraints in Redundant Reaction Wheel Configuration

NASA Technical Reports Server (NTRS)

Ha, Kong Q.; Femiano, Michael D.; Mosier, Gary E.

2004-01-01

In this paper, we present an optimal open-loop slew trajectory algorithm developed at GSFC for the so-called "Yardstick design" of the James Webb Space Telescope (JWST). JWST is an orbiting infrared observatory featuring a lightweight, segmented primary mirror approximately 6 meters in diameter and a sunshield approximately the size of a tennis court. This large, flexible structure will have significant number of lightly damped, dominant flexible modes. With very stringent requirements on pointing accuracy and image quality, it is important that slewing be done within the required time constraint and with minimal induced vibration in order to maximize observing efficiency. With reaction wheels as control actuators, initial wheel speeds as well as individual wheel torque and momentum limits become dominant constraints in slew performance. These constraints must be taken into account when performing slews to ensure that unexpected reaction wheel saturation does not occur, since such saturation leads to control failure in accurately tracking commanded motion and produces high frequency torque components capable of exciting structural modes. A minimum-time constraint is also included and coupled with reaction wheel limit constraints in the optimization to minimize both the effect of the control torque on the flexible body motion and the maneuver time. The optimization is on slew command parameters, such as maximum slew velocity and acceleration, for a given redundant reaction wheel configuration and is based on the dynamic interaction between the spacecraft and reaction wheel motion. Analytical development of the slew algorithm to generate desired slew position, rate, and acceleration profiles to command a feedback/feed forward control system is described. High-fidelity simulation and experimental results are presented to show that the developed slew law achieves the objectives.

Self-completeness and the generalized uncertainty principle

NASA Astrophysics Data System (ADS)

Isi, Maximiliano; Mureika, Jonas; Nicolini, Piero

2014-03-01

The generalized uncertainty principle discloses a self-complete characteristic of gravity, namely the possibility of masking any curvature singularity behind an event horizon as a result of matter compression at the Planck scale. In this paper we extend the above reasoning in order to overcome some current limitations to the framework, including the absence of a consistent metric describing such Planck-scale black holes. We implement a minimum-size black hole in terms of the extremal configuration of a neutral non-rotating metric, which we derived by mimicking the effects of the generalized uncertainty principle via a short scale modified version of Einstein gravity. In such a way, we find a self- consistent scenario that reconciles the self-complete character of gravity and the generalized uncertainty principle.

Self-completeness and the generalized uncertainty principle

NASA Astrophysics Data System (ADS)

Isi, Maximiliano; Mureika, Jonas; Nicolini, Piero

2013-11-01

The generalized uncertainty principle discloses a self-complete characteristic of gravity, namely the possibility of masking any curvature singularity behind an event horizon as a result of matter compression at the Planck scale. In this paper we extend the above reasoning in order to overcome some current limitations to the framework, including the absence of a consistent metric describing such Planck-scale black holes. We implement a minimum-size black hole in terms of the extremal configuration of a neutral non-rotating metric, which we derived by mimicking the effects of the generalized uncertainty principle via a short scale modified version of Einstein gravity. In such a way, we find a self-consistent scenario that reconciles the self-complete character of gravity and the generalized uncertainty principle.

On the physical basis of succussion.

PubMed

Torres, J L

2002-10-01

It is argued that succussion drives the homeopathic tincture undergoing potentisation to a turbulent regime, where vortices continually form and disappear, ranging in size from the linear extent of the container to a minimum scale determined by viscosity and the rate of energy dissipation. Input mechanical energy cascades down this population of eddies and becomes available at the microscopic level to perform work (chemical, electrical, etc). A structure generated in the tincture would be rupted by vortices smaller than it, and this sets definite limits on the strength of succussion, so the power input leads to larger vortices than the structures one is trying to create and preserve through potentisation. An experimental procedure to test this proposal is suggested, based on Rayleigh scattering.

Estimation of the simple correlation coefficient.

PubMed

Shieh, Gwowen

2010-11-01

This article investigates some unfamiliar properties of the Pearson product-moment correlation coefficient for the estimation of simple correlation coefficient. Although Pearson's r is biased, except for limited situations, and the minimum variance unbiased estimator has been proposed in the literature, researchers routinely employ the sample correlation coefficient in their practical applications, because of its simplicity and popularity. In order to support such practice, this study examines the mean squared errors of r and several prominent formulas. The results reveal specific situations in which the sample correlation coefficient performs better than the unbiased and nearly unbiased estimators, facilitating recommendation of r as an effect size index for the strength of linear association between two variables. In addition, related issues of estimating the squared simple correlation coefficient are also considered.

A review of hybrid implicit explicit finite difference time domain method

NASA Astrophysics Data System (ADS)

Chen, Juan

2018-06-01

The finite-difference time-domain (FDTD) method has been extensively used to simulate varieties of electromagnetic interaction problems. However, because of its Courant-Friedrich-Levy (CFL) condition, the maximum time step size of this method is limited by the minimum size of cell used in the computational domain. So the FDTD method is inefficient to simulate the electromagnetic problems which have very fine structures. To deal with this problem, the Hybrid Implicit Explicit (HIE)-FDTD method is developed. The HIE-FDTD method uses the hybrid implicit explicit difference in the direction with fine structures to avoid the confinement of the fine spatial mesh on the time step size. So this method has much higher computational efficiency than the FDTD method, and is extremely useful for the problems which have fine structures in one direction. In this paper, the basic formulations, time stability condition and dispersion error of the HIE-FDTD method are presented. The implementations of several boundary conditions, including the connect boundary, absorbing boundary and periodic boundary are described, then some applications and important developments of this method are provided. The goal of this paper is to provide an historical overview and future prospects of the HIE-FDTD method.

Evaluation on Dorsey Method in Surface Tension Measurement of Solder Liquids Containing Surfactants

NASA Astrophysics Data System (ADS)

Zhao, Xingke; Xie, Feiming; Fan, Jinsheng; Liu, Dayong; Huang, Jihua; Chen, Shuhai

2018-06-01

With the purpose of developing a feasible approach for measuring the surface tension of solders containing surfactants, the surface tension of Sn-3Ag-0.5Cu-xP solder alloys, with various drop sizes as well as different phosphorus (P) content, was evaluated using the Dorsey method based on the sessile drop test. The results show that the accuracy of the surface tension calculations depends on both of sessile drop size and the liquid metal composition. With a proper drop size, in the range of 4.5 mm to 5.3 mm in equivalent spherical diameters, the deviation of the surface tension calculation can be limited to 1.43 mN·m-1 and 6.30 mN·m-1 for SnAgCu and SnAgCu-P, respectively. The surface tension of SnAgCu-xP solder alloys decreases quickly to a minimum value when the P content reaches 0.5 wt% and subsequently increases slowly with the P content further increasing. The formation of a P-enriched surface layer and Sn4P3 intermetallic phases is regarded to be responsible for the decreasing and subsequent increasing of surface tension, respectively.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatt, Arpit; Zhang, Yimin; Davis, Ryan

The implementation of the US Renewable Fuel Standard is expected to increase the construction and operation of new biofuel facilities. Allowing this industry to grow without adversely affecting air quality is an important sustainability goal sought by multiple stakeholders. However, little is known about how the emission controls potentially required to comply with air quality regulations might impact biorefinery cost and deployment strategies such as siting and sizing. In this study, we use a baseline design for a lignocellulosic hydrocarbon biofuel production process to assess how the integration of emission controls impacts the minimum fuel selling price (MFSP) of themore » biofuel produced. We evaluate the change in MFSP for two cases as compared to the baseline design by incorporating (i) emission controls that ensure compliance with applicable federal air regulations and (ii) advanced control options that could be used to achieve potential best available control technology (BACT) emission limits. Our results indicate that compliance with federal air regulations can be achieved with minimal impact on biofuel cost (~$0.02 per gasoline gallon equivalent (GGE) higher than the baseline price of $5.10 GGE -1). However, if air emissions must be further reduced to meet potential BACT emission limits, the cost could increase nontrivially. For example, the MFSP could increase to $5.50 GGE -1 by adopting advanced emission controls to meet potential boiler BACT limits. Finally, given tradeoffs among emission control costs, permitting requirements, and economies of scale, these results could help inform decisions about biorefinery siting and sizing and mitigate risks associated with air permitting.« less

Comparing effects of fire modeling methods on simulated fire patterns and succession: a case study in the Missouri Ozarks

Treesearch

Jian Yang; Hong S. He; Brian R. Sturtevant; Brian R. Miranda; Eric J. Gustafson

2008-01-01

We compared four fire spread simulation methods (completely random, dynamic percolation. size-based minimum travel time algorithm. and duration-based minimum travel time algorithm) and two fire occurrence simulation methods (Poisson fire frequency model and hierarchical fire frequency model) using a two-way factorial design. We examined these treatment effects on...

Variation in clutch size in relation to nest size in birds

PubMed Central

Møller, Anders P; Adriaensen, Frank; Artemyev, Alexandr; Bańbura, Jerzy; Barba, Emilio; Biard, Clotilde; Blondel, Jacques; Bouslama, Zihad; Bouvier, Jean-Charles; Camprodon, Jordi; Cecere, Francesco; Charmantier, Anne; Charter, Motti; Cichoń, Mariusz; Cusimano, Camillo; Czeszczewik, Dorota; Demeyrier, Virginie; Doligez, Blandine; Doutrelant, Claire; Dubiec, Anna; Eens, Marcel; Eeva, Tapio; Faivre, Bruno; Ferns, Peter N; Forsman, Jukka T; García-Del-Rey, Eduardo; Goldshtein, Aya; Goodenough, Anne E; Gosler, Andrew G; Góźdź, Iga; Grégoire, Arnaud; Gustafsson, Lars; Hartley, Ian R; Heeb, Philipp; Hinsley, Shelley A; Isenmann, Paul; Jacob, Staffan; Järvinen, Antero; Juškaitis, Rimvydas; Korpimäki, Erkki; Krams, Indrikis; Laaksonen, Toni; Leclercq, Bernard; Lehikoinen, Esa; Loukola, Olli; Lundberg, Arne; Mainwaring, Mark C; Mänd, Raivo; Massa, Bruno; Mazgajski, Tomasz D; Merino, Santiago; Mitrus, Cezary; Mönkkönen, Mikko; Morales-Fernaz, Judith; Morin, Xavier; Nager, Ruedi G; Nilsson, Jan-Åke; Nilsson, Sven G; Norte, Ana C; Orell, Markku; Perret, Philippe; Pimentel, Carla S; Pinxten, Rianne; Priedniece, Ilze; Quidoz, Marie-Claude; Remeš, Vladimir; Richner, Heinz; Robles, Hugo; Rytkönen, Seppo; Senar, Juan Carlos; Seppänen, Janne T; da Silva, Luís P; Slagsvold, Tore; Solonen, Tapio; Sorace, Alberto; Stenning, Martyn J; Török, János; Tryjanowski, Piotr; van Noordwijk, Arie J; von Numers, Mikael; Walankiewicz, Wiesław; Lambrechts, Marcel M

2014-01-01

Nests are structures built to support and protect eggs and/or offspring from predators, parasites, and adverse weather conditions. Nests are mainly constructed prior to egg laying, meaning that parent birds must make decisions about nest site choice and nest building behavior before the start of egg-laying. Parent birds should be selected to choose nest sites and to build optimally sized nests, yet our current understanding of clutch size-nest size relationships is limited to small-scale studies performed over short time periods. Here, we quantified the relationship between clutch size and nest size, using an exhaustive database of 116 slope estimates based on 17,472 nests of 21 species of hole and non-hole-nesting birds. There was a significant, positive relationship between clutch size and the base area of the nest box or the nest, and this relationship did not differ significantly between open nesting and hole-nesting species. The slope of the relationship showed significant intraspecific and interspecific heterogeneity among four species of secondary hole-nesting species, but also among all 116 slope estimates. The estimated relationship between clutch size and nest box base area in study sites with more than a single size of nest box was not significantly different from the relationship using studies with only a single size of nest box. The slope of the relationship between clutch size and nest base area in different species of birds was significantly negatively related to minimum base area, and less so to maximum base area in a given study. These findings are consistent with the hypothesis that bird species have a general reaction norm reflecting the relationship between nest size and clutch size. Further, they suggest that scientists may influence the clutch size decisions of hole-nesting birds through the provisioning of nest boxes of varying sizes. PMID:25478150

Variation in clutch size in relation to nest size in birds.

PubMed

Møller, Anders P; Adriaensen, Frank; Artemyev, Alexandr; Bańbura, Jerzy; Barba, Emilio; Biard, Clotilde; Blondel, Jacques; Bouslama, Zihad; Bouvier, Jean-Charles; Camprodon, Jordi; Cecere, Francesco; Charmantier, Anne; Charter, Motti; Cichoń, Mariusz; Cusimano, Camillo; Czeszczewik, Dorota; Demeyrier, Virginie; Doligez, Blandine; Doutrelant, Claire; Dubiec, Anna; Eens, Marcel; Eeva, Tapio; Faivre, Bruno; Ferns, Peter N; Forsman, Jukka T; García-Del-Rey, Eduardo; Goldshtein, Aya; Goodenough, Anne E; Gosler, Andrew G; Góźdź, Iga; Grégoire, Arnaud; Gustafsson, Lars; Hartley, Ian R; Heeb, Philipp; Hinsley, Shelley A; Isenmann, Paul; Jacob, Staffan; Järvinen, Antero; Juškaitis, Rimvydas; Korpimäki, Erkki; Krams, Indrikis; Laaksonen, Toni; Leclercq, Bernard; Lehikoinen, Esa; Loukola, Olli; Lundberg, Arne; Mainwaring, Mark C; Mänd, Raivo; Massa, Bruno; Mazgajski, Tomasz D; Merino, Santiago; Mitrus, Cezary; Mönkkönen, Mikko; Morales-Fernaz, Judith; Morin, Xavier; Nager, Ruedi G; Nilsson, Jan-Åke; Nilsson, Sven G; Norte, Ana C; Orell, Markku; Perret, Philippe; Pimentel, Carla S; Pinxten, Rianne; Priedniece, Ilze; Quidoz, Marie-Claude; Remeš, Vladimir; Richner, Heinz; Robles, Hugo; Rytkönen, Seppo; Senar, Juan Carlos; Seppänen, Janne T; da Silva, Luís P; Slagsvold, Tore; Solonen, Tapio; Sorace, Alberto; Stenning, Martyn J; Török, János; Tryjanowski, Piotr; van Noordwijk, Arie J; von Numers, Mikael; Walankiewicz, Wiesław; Lambrechts, Marcel M

2014-09-01

Nests are structures built to support and protect eggs and/or offspring from predators, parasites, and adverse weather conditions. Nests are mainly constructed prior to egg laying, meaning that parent birds must make decisions about nest site choice and nest building behavior before the start of egg-laying. Parent birds should be selected to choose nest sites and to build optimally sized nests, yet our current understanding of clutch size-nest size relationships is limited to small-scale studies performed over short time periods. Here, we quantified the relationship between clutch size and nest size, using an exhaustive database of 116 slope estimates based on 17,472 nests of 21 species of hole and non-hole-nesting birds. There was a significant, positive relationship between clutch size and the base area of the nest box or the nest, and this relationship did not differ significantly between open nesting and hole-nesting species. The slope of the relationship showed significant intraspecific and interspecific heterogeneity among four species of secondary hole-nesting species, but also among all 116 slope estimates. The estimated relationship between clutch size and nest box base area in study sites with more than a single size of nest box was not significantly different from the relationship using studies with only a single size of nest box. The slope of the relationship between clutch size and nest base area in different species of birds was significantly negatively related to minimum base area, and less so to maximum base area in a given study. These findings are consistent with the hypothesis that bird species have a general reaction norm reflecting the relationship between nest size and clutch size. Further, they suggest that scientists may influence the clutch size decisions of hole-nesting birds through the provisioning of nest boxes of varying sizes.

25 CFR 542.22 - What are the minimum internal control standards for internal audit for Tier A gaming operations?

Code of Federal Regulations, 2010 CFR

2010-04-01

... but not limited to, bingo card control, payout procedures, and cash reconciliation process; (ii) Pull... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum internal control standards for... COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.22 What are...

25 CFR 542.32 - What are the minimum internal control standards for internal audit for Tier B gaming operations?

Code of Federal Regulations, 2010 CFR

2010-04-01

... but not limited to, bingo card control, payout procedures, and cash reconciliation process; (ii) Pull... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum internal control standards for... COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.32 What are...

The Age 21 Minimum Legal Drinking Age Law. Prevention Update

ERIC Educational Resources Information Center

Higher Education Center for Alcohol, Drug Abuse, and Violence Prevention, 2011

2011-01-01

Currently, all 50 states limit alcohol purchases to people aged 21 and over. But that hasn't always been the case. In fact, it was July 17, 1984, when President Ronald Reagan signed the national 21 minimum legal drinking age (MLDA) legislation into law. At that time, only 23 states had minimum alcohol purchasing ages of 21 years old. The…

Size-Constrained Region Merging: A New Tool to Derive Basic Landcover Units from Remote Sensing Imagery

NASA Astrophysics Data System (ADS)

Castilla, G.

2004-09-01

Landcover maps typically represent the territory as a mosaic of contiguous units "polygons- that are assumed to correspond to geographic entities" like e.g. lakes, forests or villages-. They may also be viewed as representing a particular level of a landscape hierarchy where each polygon is a holon - an object made of subobjects and part of a superobject. The focal level portrayed in the map is distinguished from other levels by the average size of objects compounding it. Moreover, the focal level is bounded by the minimum size that objects of this level are supposed to have. Based on this framework, we have developed a segmentation method that defines a partition on a multiband image such that i) the mean size of segments is close to the one specified; ii) each segment exceeds the required minimum size; and iii) the internal homogeneity of segments is maximal given the size constraints. This paper briefly describes the method, focusing on its region merging stage. The most distinctive feature of the latter is that while the merging sequence is ordered by increasing dissimilarity as in conventional methods, there is no need to define a threshold on the dissimilarity measure between adjacent segments.

Minimum-sized ideal reactor for continuous alcohol fermentation using immobilized microorganism

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamane, T.; Shimizu, S.

Recently, alcohol fermentation has gained considerable attention with the aim of lowering its production cost in the production processes of both fuel ethanol and alcoholic beverages. The over-all cost is a summation of costs of various subsystems such as raw material (sugar, starch, and cellulosic substances) treatment, fermentation process, and alcohol separation from water solutions; lowering the cost of the fermentation processes is very important in lowering the total cost. Several new techniques have been developed for economic continuous ethanol production, use of a continuous wine fermentor with no mechanical stirring, cell recycle combined with continuous removal of ethanol undermore » vaccum, a technique involving a bed of yeast admixed with an inert carrier, and use of immobilized yeast reactors in packed-bed column and in a three-stage double conical fluidized-bed bioreactor. All these techniques lead to increases more or less, in reactor productivity, which in turn result in the reduction of the reactor size for a given production rate and a particular conversion. Since an improvement in the fermentation process often leads to a reduction of fermentor size and hence, a lowering of the initial construction cost, it is important to theoretically arrive at a solution to what is the minimum-size setup of ideal reactors from the viewpoint of liquid backmixing. In this short communication, the minimum-sized ideal reactor for continuous alcohol fermentation using immobilized cells will be specifically discussed on the basis of a mathematical model. The solution will serve for designing an optimal bioreactor. (Refs. 26).« less

Comparison and verification of two models which predict minimum principal in situ stress from triaxial data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harikrishnan, R.; Hareland, G.; Warpinski, N.R.

This paper evaluates the correlation between values of minimum principal in situ stress derived from two different models which use data obtained from triaxial core tests and coefficient for earth at rest correlations. Both models use triaxial laboratory tests with different confining pressures. The first method uses a vcrified fit to the Mohr failure envelope as a function of average rock grain size, which was obtained from detailed microscopic analyses. The second method uses the Mohr-Coulomb failure criterion. Both approaches give an angle in internal friction which is used to calculate the coefficient for earth at rest which gives themore » minimum principal in situ stress. The minimum principal in situ stress is then compared to actual field mini-frac test data which accurately determine the minimum principal in situ stress and are used to verify the accuracy of the correlations. The cores and the mini-frac stress test were obtained from two wells, the Gas Research Institute`s (GRIs) Staged Field Experiment (SFE) no. 1 well through the Travis Peak Formation in the East Texas Basin, and the Department of Energy`s (DOE`s) Multiwell Experiment (MWX) wells located west-southwest of the town of Rifle, Colorado, near the Rulison gas field. Results from this study indicates that the calculated minimum principal in situ stress values obtained by utilizing the rock failure envelope as a function of average rock grain size correlation are in better agreement with the measured stress values (from mini-frac tests) than those obtained utilizing Mohr-Coulomb failure criterion.« less

37 CFR 385.13 - Minimum royalty rates and subscriber-based royalty floors for specific types of services.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., and Copyrights COPYRIGHT ROYALTY BOARD, LIBRARY OF CONGRESS RATES AND TERMS FOR STATUTORY LICENSES... PHYSICAL AND DIGITAL PHONORECORDS Interactive Streaming and Limited Downloads § 385.13 Minimum royalty...

The human, primate and rabbit ultraviolet action spectra

NASA Technical Reports Server (NTRS)

Pitts, D. G.; Gibbons, W. D.

1972-01-01

A 5000 watt xenon-mercury high pressure lamp was used to produce a continuous ultraviolet spectrum. Human and animal exposures were made to establish the photokeratitis threshold and abiotic action spectrum. The lower limit of the abiotic action spectrum was 220 nm while the upper limit was 310 nm. The radiant exposure threshold at 270 nm was 0.005 watts/sq cm for the rabbit, 0.004 watts/sq cm for the primate, and 0.004 watts/ sq cm for the human. The rabbit curve was bi-peaked with minimums at 220 nm, 240 nm and 270 nm. The primate curve was tri-peaked with minimums at 220 nm, 240 nm and 270 nm. The human data showed a rather shallow curve with a minimum at 270 nm. Formulas and calculations are given to predict minimum exposure times for ocular damage to man in outer space, to establish valid safety criteria, and to establish protective design criteria.

Probable flood predictions in ungauged coastal basins of El Salvador

USGS Publications Warehouse

Friedel, M.J.; Smith, M.E.; Chica, A.M.E.; Litke, D.

2008-01-01

A regionalization procedure is presented and used to predict probable flooding in four ungauged coastal river basins of El Salvador: Paz, Jiboa, Grande de San Miguel, and Goascoran. The flood-prediction problem is sequentially solved for two regions: upstream mountains and downstream alluvial plains. In the upstream mountains, a set of rainfall-runoff parameter values and recurrent peak-flow discharge hydrographs are simultaneously estimated for 20 tributary-basin models. Application of dissimilarity equations among tributary basins (soft prior information) permitted development of a parsimonious parameter structure subject to information content in the recurrent peak-flow discharge values derived using regression equations based on measurements recorded outside the ungauged study basins. The estimated joint set of parameter values formed the basis from which probable minimum and maximum peak-flow discharge limits were then estimated revealing that prediction uncertainty increases with basin size. In the downstream alluvial plain, model application of the estimated minimum and maximum peak-flow hydrographs facilitated simulation of probable 100-year flood-flow depths in confined canyons and across unconfined coastal alluvial plains. The regionalization procedure provides a tool for hydrologic risk assessment and flood protection planning that is not restricted to the case presented herein. ?? 2008 ASCE.

7 CFR 984.11 - Merchantable walnuts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... means all inshell walnuts meeting the minimum grade and size regulations effective pursuant to § 984.50... size regulations effective pursuant to § 984.50. [27 FR 9094, Sept. 13, 1962, as amended at 39 FR 35328...

76 FR 30417 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-25

... Change Amending Rule 7.31(h)(5) To Reduce the Minimum Order Entry Size of a Mid-Point Passive Liquidity... order entry size of a Mid-Point Passive Liquidity Order (``MPL Order'') from 100 shares to one share...

A new design approach to achieve a minimum impulse limit cycle in the presence of significant measurement uncertainties

NASA Technical Reports Server (NTRS)

Martin, M. W.; Kubiak, E. T.

1982-01-01

A new design was developed for the Space Shuttle Transition Phase Digital Autopilot to reduce the impact of large measurement uncertainties in the rate signal during attitude control. The signal source, which was dictated by early computer constraints, is characterized by large quantization, noise, bias, and transport lag which produce a measurement uncertainty larger than the minimum impulse rate change. To ensure convergence to a minimum impulse limit cycle, the design employed bias and transport lag compensation and a switching logic with hysteresis, rate deadzone, and 'walking' switching line. The design background, the rate measurement uncertainties, and the design solution are documented.

The behavior of self-compacting concrete (SCC) with bagasse ash

NASA Astrophysics Data System (ADS)

Hanafiah, Saloma, Whardani, Putri Nurul Kusuma

2017-11-01

Self-Compacting Concrete (SCC) has the ability to flow and self-compacting. One of the benefit of SCC can reduced the construction time and labor cost. The materials to be used for see slightly different with the conventional concrete. Less coarse aggregate to be used up to 50%. The maximum size of coarse aggregate was also limited e.g. 10 mm. Other material was quartz sand with grain size of 50-650 µm. For reducing the around of cement, bagasse ash was used as partial replacement of cement. In this research, the variations of w/c to be used, e.g. 0.275, 0.300, 0.325 and the percentage of bagasse ash substitution were 10%, 15%, and 20%. EFNARC standard was conducted for slump flow test following the V-funnel test and L-box shape test. The maximum value of slump flow test was 75.75 cm, V-funnel test was 4.95 second, and L-box test was 1.000 yielded by mixture with w/c = 0.325 and 0% of bagasse ash. The minimum value of slump flow test was 61.50 cm, V-funnel test is 21.05 second, and L-box test was 0.743 yielded by mixture with w/c = 0.275 and 20% of bagasse ash. The maximum value of compressive strength was 67.239 MPa yielded by mixture with w/c = 0.275 and 15% of bagasse ash. And the minimum value of compressive strength was 41.813 MPa yielded by mixture with w/c = 0.325 and 20% bagasse ash.

Limits to Open Class Performance?

NASA Technical Reports Server (NTRS)

Bowers, Albion H.

2008-01-01

This presentation discusses open or unlimited class aircraft performance limitations and design solutions. Limitations in this class of aircraft include slow climbing flight which requires low wing loading, high cruise speed which requires high wing loading, gains in induced or viscous drag alone which result in only half the gain overall and other structural problems (yaw inertia and spins, flutter and static loads integrity). Design solutions include introducing minimum induced drag for a given span (elliptical span load or winglets) and introducing minimum induced drag for a bell shaped span load. It is concluded that open class performance limits (under current rules and technologies) is very close to absolute limits, though some gains remain to be made from unexplored areas and new technologies.

A Transmission Electron Microscope Study of Experimentally Shocked Pregraphitic Carbon

NASA Technical Reports Server (NTRS)

Rietmeijer, Frans J. M.

1995-01-01

A transmission electron microscope study of experimental shock metamorphism in natural pre-graphitic carbon simulates the response of the most common natural carbons to increased shock pressure. The d-spacings of this carbon are insensitive to the shock pressure and have no apparent diagnostic value, but progressive comminution occurs in response to increased shock pressure up to 59.6 GPa. The function, P = 869.1 x (size(sub minimum )(exp -0.83), describes the relationship between the minimum root-mean-square subgrain size (nm) and shock pressure (GPa). While a subgrain texture of natural pregraphitic carbons carries little information when pre-shock textures are unknown, this texture may go unnoticed as a shock metamorphic feature.

A Comparison of the Fit of Empirical Data to Two Latent Trait Models. Report No. 92.

ERIC Educational Resources Information Center

Hutten, Leah R.

Goodness of fit of raw test score data were compared, using two latent trait models: the Rasch model and the Birnbaum three-parameter logistic model. Data were taken from various achievement tests and the Scholastic Aptitude Test (Verbal). A minimum sample size of 1,000 was required, and the minimum test length was 40 items. Results indicated that…

USSR Report International Affairs.

DTIC Science & Technology

1986-09-02

minimum interest rate (price of a loan), proportion of the value of a contract to be covered by an easy loan (minimum size of payments in cash...Kuwait Laos Lebanon Malaysia Mongolian People’s Republic Nepal Pakistan Saudi Arabia Singapore Syria Turnover Export Import Turnover...including the blockade imposed on export financing. The latter was started in July 1980 by swiftly increasing the interest rates on foreign trade loans

The Consequences of Indexing the Minimum Wage to Average Wages in the U.S. Economy.

ERIC Educational Resources Information Center

Macpherson, David A.; Even, William E.

The consequences of indexing the minimum wage to average wages in the U.S. economy were analyzed. The study data were drawn from the 1974-1978 May Current Population Survey (CPS) and the 180 monthly CPS Outgoing Rotation Group files for 1979-1993 (approximate annual sample sizes of 40,000 and 180,000, respectively). The effects of indexing on the…

Variability of space climate and its extremes with successive solar cycles

NASA Astrophysics Data System (ADS)

Chapman, Sandra; Hush, Phillip; Tindale, Elisabeth; Dunlop, Malcolm; Watkins, Nicholas

2016-04-01

Auroral geomagnetic indices coupled with in situ solar wind monitors provide a comprehensive data set, spanning several solar cycles. Space climate can be considered as the distribution of space weather. We can then characterize these observations in terms of changing space climate by quantifying how the statistical properties of ensembles of these observed variables vary between different phases of the solar cycle. We first consider the AE index burst distribution. Bursts are constructed by thresholding the AE time series; the size of a burst is the sum of the excess in the time series for each time interval over which the threshold is exceeded. The distribution of burst sizes is two component with a crossover in behaviour at thresholds ≈ 1000 nT. Above this threshold, we find[1] a range over which the mean burst size is almost constant with threshold for both solar maxima and minima. The burst size distribution of the largest events has a functional form which is exponential. The relative likelihood of these large events varies from one solar maximum and minimum to the next. If the relative overall activity of a solar maximum/minimum can be estimated, these results then constrain the likelihood of extreme events of a given size for that solar maximum/minimum. We next develop and apply a methodology to quantify how the full distribution of geomagnetic indices and upstream solar wind observables are changing between and across different solar cycles. This methodology[2] estimates how different quantiles of the distribution, or equivalently, how the return times of events of a given size, are changing. [1] Hush, P., S. C. Chapman, M. W. Dunlop, and N. W. Watkins (2015), Robust statistical properties of the size of large burst events in AE, Geophys. Res. Lett.,42 doi:10.1002/2015GL066277 [2] Chapman, S. C., D. A. Stainforth, N. W. Watkins, (2013) On estimating long term local climate trends , Phil. Trans. Royal Soc., A,371 20120287 DOI:10.1098/rsta.2012.0287

[Trial of eye drops recognizer for visually disabled persons].

PubMed

Okamoto, Norio; Suzuki, Katsuhiko; Mimura, Osamu

2009-01-01

The development of a device to enable the visually disabled to differentiate eye drops and their dose. The new instrument is composed of a voice generator and a two-dimensional bar-code reader (LS9208). We designed voice outputs for the visually disabled to state when (number of times) and where (right, left, or both) to administer eye drops. We then determined the minimum bar-code size that can be recognized. After attaching bar-codes of the appropriate size to the lateral or bottom surface of the eye drops container, the readability of the bar-codes was compared. The minimum discrimination bar-code size was 6 mm high x 8.5 mm long. Bar-codes on the bottom surface could be more easily recognized than bar-codes on the side. Our newly-developed device using bar-codes enables visually disabled persons to differentiate eye drops and their doses.

A rapid method for optimization of the rocket propulsion system for single-stage-to-orbit vehicles

NASA Technical Reports Server (NTRS)

Eldred, C. H.; Gordon, S. V.

1976-01-01

A rapid analytical method for the optimization of rocket propulsion systems is presented for a vertical take-off, horizontal landing, single-stage-to-orbit launch vehicle. This method utilizes trade-offs between propulsion characteristics affecting flight performance and engine system mass. The performance results from a point-mass trajectory optimization program are combined with a linearized sizing program to establish vehicle sizing trends caused by propulsion system variations. The linearized sizing technique was developed for the class of vehicle systems studied herein. The specific examples treated are the optimization of nozzle expansion ratio and lift-off thrust-to-weight ratio to achieve either minimum gross mass or minimum dry mass. Assumed propulsion system characteristics are high chamber pressure, liquid oxygen and liquid hydrogen propellants, conventional bell nozzles, and the same fixed nozzle expansion ratio for all engines on a vehicle.

Design of landfill daily cells.

PubMed

Panagiotakopoulos, D; Dokas, I

2001-08-01

The objective of this paper is to study the behaviour of the landfill soil-to-refuse (S/R) ratio when size, geometry and operating parameters of the daily cell vary over realistic ranges. A simple procedure is presented (1) for calculating the cell parameters values which minimise the S/R ratio and (2) for studying the sensitivity of this minimum S/R ratio to variations in cell size, final refuse density, working face length, lift height and cover thickness. In countries where daily soil cover is required, savings in landfill space could be realised following this procedure. The sensitivity of minimum S/R to variations in cell dimensions decreases with cell size. Working face length and lift height affect the S/R ratio significantly. This procedure also offers the engineer an additional tool for comparing one large daily cell with two or more smaller ones, at two different working faces within the same landfill.

Techno-economic assessment of pellets produced from steam pretreated biomass feedstock

DOE PAGES

Shahrukh, Hassan; Oyedun, Adetoyese Olajire; Kumar, Amit; ...

2016-03-10

Minimum production cost and optimum plant size are determined for pellet plants for three types of biomass feedstock e forest residue, agricultural residue, and energy crops. The life cycle cost from harvesting to the delivery of the pellets to the co-firing facility is evaluated. The cost varies from 95 to 105 t -1 for regular pellets and 146–156 t -1 for steam pretreated pellets. The difference in the cost of producing regular and steam pretreated pellets per unit energy is in the range of 2e3 GJ -1. The economic optimum plant size (i.e., the size at which pellet production costmore » is minimum) is found to be 190 kt for regular pellet production and 250 kt for steam pretreated pellet. Furthermore, sensitivity and uncertainty analyses were carried out to identify sensitivity parameters and effects of model error.« less

STS mission duration enhancement study: (orbiter habitability)

NASA Technical Reports Server (NTRS)

Carlson, A. D.

1979-01-01

Habitability improvements for early flights that could be implemented with minimum impact were investigated. These included: (1) launching the water dispenser in the on-orbit position instead of in a locker; (2) the sleep pallet concept; and (3) suction cup foot restraints. Past studies that used volumetric terms and requirements for crew size versus mission duration were reviewed and common definitions of key habitability terms were established. An accurately dimensioned drawing of the orbiter mid-deck, locating all of the known major elements was developed. Finally, it was established that orbiter duration and crew size can be increased with minimum modification and impact to the crew module. Preliminary concepts of the aft med-deck, external versions of expanded tunnel adapters (ETA), and interior concepts of ETA-3 were developed and comparison charts showing the various factors of volume, weight, duration, size, impact to orbiter, and number of sleep stations were generated.

Sample Size and Allocation of Effort in Point Count Sampling of Birds in Bottomland Hardwood Forests

Treesearch

Winston P. Smith; Daniel J. Twedt; Robert J. Cooper; David A. Wiedenfeld; Paul B. Hamel; Robert P. Ford

1995-01-01

To examine sample size requirements and optimum allocation of effort in point count sampling of bottomland hardwood forests, we computed minimum sample sizes from variation recorded during 82 point counts (May 7-May 16, 1992) from three localities containing three habitat types across three regions of the Mississippi Alluvial Valley (MAV). Also, we estimated the effect...

Monitoring Species of Concern Using Noninvasive Genetic Sampling and Capture-Recapture Methods

DTIC Science & Technology

2016-11-01

ABBREVIATIONS AICc Akaike’s Information Criterion with small sample size correction AZGFD Arizona Game and Fish Department BMGR Barry M. Goldwater...MNKA Minimum Number Known Alive N Abundance Ne Effective Population Size NGS Noninvasive Genetic Sampling NGS-CR Noninvasive Genetic...parameter estimates from capture-recapture models require sufficient sample sizes , capture probabilities and low capture biases. For NGS-CR, sample

Ensemble Learning Method for Hidden Markov Models

DTIC Science & Technology

2014-12-01

Ensemble HMM landmine detector Mine signatures vary according to the mine type, mine size , and burial depth. Similarly, clutter signatures vary with soil ...approaches for the di erent K groups depending on their size and homogeneity. In particular, we investigate the maximum likelihood (ML), the minimum...propose using and optimizing various training approaches for the different K groups depending on their size and homogeneity. In particular, we

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to a line from stem to blossom end. When measuring for maximum size, “diameter” means the smallest dimension of the apple determined by...

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to a line from stem to blossom end. When measuring for maximum size, “diameter” means the smallest dimension of the apple determined by...

7 CFR 51.320 - Diameter.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Standards for Grades of Apples Definitions § 51.320 Diameter. When measuring for minimum size, “diameter” means the greatest dimension of the apple measured at right angles to a line from stem to blossom end. When measuring for maximum size, “diameter” means the smallest dimension of the apple determined by...

Kidney function endpoints in kidney transplant trials: a struggle for power.

PubMed

Ibrahim, A; Garg, A X; Knoll, G A; Akbari, A; White, C A

2013-03-01

Kidney function endpoints are commonly used in randomized controlled trials (RCTs) in kidney transplantation (KTx). We conducted this study to estimate the proportion of ongoing RCTs with kidney function endpoints in KTx where the proposed sample size is large enough to detect meaningful differences in glomerular filtration rate (GFR) with adequate statistical power. RCTs were retrieved using the key word "kidney transplantation" from the National Institute of Health online clinical trial registry. Included trials had at least one measure of kidney function tracked for at least 1 month after transplant. We determined the proportion of two-arm parallel trials that had sufficient sample sizes to detect a minimum 5, 7.5 and 10 mL/min difference in GFR between arms. Fifty RCTs met inclusion criteria. Only 7% of the trials were above a sample size of 562, the number needed to detect a minimum 5 mL/min difference between the groups should one exist (assumptions: α = 0.05; power = 80%, 10% loss to follow-up, common standard deviation of 20 mL/min). The result increased modestly to 36% of trials when a minimum 10 mL/min difference was considered. Only a minority of ongoing trials have adequate statistical power to detect between-group differences in kidney function using conventional sample size estimating parameters. For this reason, some potentially effective interventions which ultimately could benefit patients may be abandoned from future assessment. © Copyright 2013 The American Society of Transplantation and the American Society of Transplant Surgeons.

Size-related mortality due to gnathiid isopod micropredation correlates with settlement size in coral reef fishes

NASA Astrophysics Data System (ADS)

Grutter, A. S.; Blomberg, S. P.; Fargher, B.; Kuris, A. M.; McCormick, M. I.; Warner, R. R.

2017-06-01

The transition between the planktonic and the benthic habitat is a critical period for the larvae of many demersal marine organisms. Understanding the potential constraints on the timing of this habitat transition, called settlement, is important to understanding their biology. Size-specific mortality can set the limits on lifestyle and help explain ontogenetic habitat shifts. We examined whether size-based mortality risks after settlement may include micropredation by ectoparasites by testing whether survival of settlement-stage fish varies with fish size when exposed to a reef-associated micropredator. Fish (14 species) were exposed to one blood-sucking gnathiid isopod overnight, with appropriate controls; gnathiid feeding success and survival, and fish mortality were recorded relative to fish size. After adjusting for fish relatedness, we found the relationship between fish mortality and size differed with gnathiid exposure: for gnathiid-exposed fish, the mean mortality of the smallest fish was much higher (57%) than unexposed controls (10%), and decreased to 0% for fish >12 mm standard length (SL); mortality was almost nil in controls. Thus, a predicted optimal size to switch habitat and reduce mortality risk from micropredation should be >12 mm SL. We then asked what species might be at greater risk and if the steep increase in survival at 12 mm SL might coincide with settlement at larger sizes among fishes. Across 102 other species (32 families), 61% settled at ≥12 mm SL. After adjusting for relatedness, mean fish settlement size was 15.0 mm and this was not significantly different from 12 mm. Thus, settlement size clusters around the minimum fish size threshold our gnathiid experiment predicted would be large enough to survive a gnathiid encounter. These results suggest micropredators may contribute to size-selective mortality during settlement processes and are consistent with the hypothesis that the pelagic phase provides fish an escape from certain micropredators.

Fluorescein Dye Penetration in Round Top Rhyolite (Hudspeth County, Texas, USA) to Reveal Micro-permeability and Optimize Grain Size for Heavy REE Heap Leach

NASA Astrophysics Data System (ADS)

Negron, L. M.; Clague, J. W.; Gorski, D.; Amaya, M. A.; Pingitore, N. E.

2013-12-01

Millimeter- and micrometer-scale permeability of fine-grained igneous rocks has generated limited research interest. Nonetheless, the scale and distribution of such micro-permeability determines fluid penetration and pathways, parameters that define both the ability to heap leach a rock and the optimal grain size for such an operation. Texas Rare Earth Resources is evaluating the possibility of heap leaching of yttrium and heavy rare earth elements (YHREE) from the peraluminous rhyolite laccolith that forms one-mile-diameter Round Top Mountain. The YHREEs in this immense, surface-exposed deposit (minimum 1.6 billion tons, Texas Bureau Economic Geology) are dilute and diffuse, suggesting leaching as the best option for recovery. The REE grade is 0.05% and YHREEs comprise more than 70% of the total REE content. The YHREEs are hosted exclusively in micron-scale yttrofluorite grains, which proved soluble in dilute sulfuric acid. Laboratory experiments showed YHREE recoveries of up to 90%. Within limits, recoveries decrease with larger grain sizes, and increase with acid strength and exposure time. Our research question centers on dissolution effectiveness: Is YHREE recovery, relative to grain size, limited by (1) diffusion time of acid into, and dissolved solids, including YHREEs, out of the micro-permeability paths inherent in the rock particles; (2) the effective lengths of the natural micro-permeability paths in the rock; or (3) the putative role of the acid in dissolving new micro-paths into the grains? The maximum grain size should not exceed twice the typical path length (unless acid creates new paths), lest YHREEs in the core of a larger grain than that not be reached by acid. If instead diffusion time is limiting, longer leach time may prove effective. Rather than perform an extensive and expensive series of laboratory leaching experiments--some of which would be several months in duration--to determine optimal grain size, we developed a technique to efficiently determine the limits of penetration of water into the rhyolite. We cut parallel-sided slabs of Round Top rhyolite at staged thickness up to 10 mm. We then wet one side and view the opposite side over time under UV light to detect breakthrough of the fluorescein dye. Because of its extremely low visual detection limits, well below the ppm level, the dye has been widely used in biochemical research, as a tracer in surface and ground water studies, in delineating invisible cracks in such structural material as motor blocks, and in detecting corneal abrasions. We have been successful in detecting breakthrough at different rhyolite thicknesses. Continuing studies focus on mapping of the 2-dimensional distribution of the permeability via hand lens and low-power microscope; use of visible light dyes; and examination of specimens pre- and post-acid leaching to determine whether acid exposure produced significant new micro-permeability.

Use of population viability analysis to evaluate CITES trade-management options for threatened marine fishes.

PubMed

Curtis, Janelle M R; Vincent, Amanda C J

2008-10-01

Achieving multiple conservation objectives can be challenging, particularly under high uncertainty. Having agreed to limit seahorse (Hippocampus) exports to sustainable levels, signatories to the Convention on International Trade in Endangered Species of Wild Fauna and Flora (CITES) were offered the option of a single 10-cm minimum size limit (MSL) as an interim management measure for all Hippocampus species (> or =34). Although diverse stakeholders supported the recommended MSL, its biological and socioeconomic implications were not assessed quantitatively. We combined population viability analysis, model sensitivity analysis, and economic information to evaluate the trade-off between conservation threat to and long-term cumulative income from these exploited marine fishes of high conservation concern. We used the European long-snouted seahorse (Hippocampus guttulatus) as a representative species to compare the performance of MSLs set at alternative biological reference points. Our sensitivity analyses showed that in most of our scenarios, setting the MSL just above size at maturity (9.7 cm in H. guttulatus) would not prevent exploited populations from becoming listed as vulnerable. By contrast, the relative risk of decline and extinction were almost halved--at a cost of only a 5.6% reduction in long-term catches--by increasing the MSL to the size reached after at least one full reproductive season. On the basis of our analysis, a precautionary increase in the MSL could be compatible with sustaining fishers' livelihoods and international trade. Such management tactics that aid species conservation and have minimal effects on long term catch trends may help bolster the case for CITES trade management of other valuable marine fishes.

Microbial eukaryote diversity in the marine oxygen minimum zone off northern Chile.

PubMed

Parris, Darren J; Ganesh, Sangita; Edgcomb, Virginia P; DeLong, Edward F; Stewart, Frank J

2014-01-01

Molecular surveys are revealing diverse eukaryotic assemblages in oxygen-limited ocean waters. These communities may play pivotal ecological roles through autotrophy, feeding, and a wide range of symbiotic associations with prokaryotes. We used 18S rRNA gene sequencing to provide the first snapshot of pelagic microeukaryotic community structure in two cellular size fractions (0.2-1.6 μm, >1.6 μm) from seven depths through the anoxic oxygen minimum zone (OMZ) off northern Chile. Sequencing of >154,000 amplicons revealed contrasting patterns of phylogenetic diversity across size fractions and depths. Protist and total eukaryote diversity in the >1.6 μm fraction peaked at the chlorophyll maximum in the upper photic zone before declining by ~50% in the OMZ. In contrast, diversity in the 0.2-1.6 μm fraction, though also elevated in the upper photic zone, increased four-fold from the lower oxycline to a maximum at the anoxic OMZ core. Dinoflagellates of the Dinophyceae and endosymbiotic Syndiniales clades dominated the protist assemblage at all depths (~40-70% of sequences). Other protist groups varied with depth, with the anoxic zone community of the larger size fraction enriched in euglenozoan flagellates and acantharean radiolarians (up to 18 and 40% of all sequences, respectively). The OMZ 0.2-1.6 μm fraction was dominated (11-99%) by Syndiniales, which exhibited depth-specific variation in composition and total richness despite uniform oxygen conditions. Metazoan sequences, though confined primarily to the 1.6 μm fraction above the OMZ, were also detected within the anoxic zone where groups such as copepods increased in abundance relative to the oxycline and upper OMZ. These data, compared to those from other low-oxygen sites, reveal variation in OMZ microeukaryote composition, helping to identify clades with potential adaptations to oxygen-depletion.

Microbial eukaryote diversity in the marine oxygen minimum zone off northern Chile

PubMed Central

Parris, Darren J.; Ganesh, Sangita; Edgcomb, Virginia P.; DeLong, Edward F.; Stewart, Frank J.

2014-01-01

Molecular surveys are revealing diverse eukaryotic assemblages in oxygen-limited ocean waters. These communities may play pivotal ecological roles through autotrophy, feeding, and a wide range of symbiotic associations with prokaryotes. We used 18S rRNA gene sequencing to provide the first snapshot of pelagic microeukaryotic community structure in two cellular size fractions (0.2–1.6 μm, >1.6 μm) from seven depths through the anoxic oxygen minimum zone (OMZ) off northern Chile. Sequencing of >154,000 amplicons revealed contrasting patterns of phylogenetic diversity across size fractions and depths. Protist and total eukaryote diversity in the >1.6 μm fraction peaked at the chlorophyll maximum in the upper photic zone before declining by ~50% in the OMZ. In contrast, diversity in the 0.2–1.6 μm fraction, though also elevated in the upper photic zone, increased four-fold from the lower oxycline to a maximum at the anoxic OMZ core. Dinoflagellates of the Dinophyceae and endosymbiotic Syndiniales clades dominated the protist assemblage at all depths (~40–70% of sequences). Other protist groups varied with depth, with the anoxic zone community of the larger size fraction enriched in euglenozoan flagellates and acantharean radiolarians (up to 18 and 40% of all sequences, respectively). The OMZ 0.2–1.6 μm fraction was dominated (11–99%) by Syndiniales, which exhibited depth-specific variation in composition and total richness despite uniform oxygen conditions. Metazoan sequences, though confined primarily to the 1.6 μm fraction above the OMZ, were also detected within the anoxic zone where groups such as copepods increased in abundance relative to the oxycline and upper OMZ. These data, compared to those from other low-oxygen sites, reveal variation in OMZ microeukaryote composition, helping to identify clades with potential adaptations to oxygen-depletion. PMID:25389417

Minimum information about a single amplified genome (MISAG) and a metagenome-assembled genome (MIMAG) of bacteria and archaea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowers, Robert M.; Kyrpides, Nikos C.; Stepanauskas, Ramunas

We present two standards developed by the Genomic Standards Consortium (GSC) for reporting bacterial and archaeal genome sequences. Both are extensions of the Minimum Information about Any (x) Sequence (MIxS). The standards are the Minimum Information about a Single Amplified Genome (MISAG) and the Minimum Information about a Metagenome-Assembled Genome (MIMAG), including, but not limited to, assembly quality, and estimates of genome completeness and contamination. These standards can be used in combination with other GSC checklists, including the Minimum Information about a Genome Sequence (MIGS), Minimum Information about a Metagenomic Sequence (MIMS), and Minimum Information about a Marker Gene Sequencemore » (MIMARKS). Community-wide adoption of MISAG and MIMAG will facilitate more robust comparative genomic analyses of bacterial and archaeal diversity.« less

Minimum information about a single amplified genome (MISAG) and a metagenome-assembled genome (MIMAG) of bacteria and archaea

DOE PAGES

Bowers, Robert M.; Kyrpides, Nikos C.; Stepanauskas, Ramunas; ...

2017-08-08

Here, we present two standards developed by the Genomic Standards Consortium (GSC) for reporting bacterial and archaeal genome sequences. Both are extensions of the Minimum Information about Any (x) Sequence (MIxS). The standards are the Minimum Information about a Single Amplified Genome (MISAG) and the Minimum Information about a MetagenomeAssembled Genome (MIMAG), including, but not limited to, assembly quality, and estimates of genome completeness and contamination. These standards can be used in combination with other GSC checklists, including the Minimum Information about a Genome Sequence (MIGS), Minimum Information about a Metagenomic Sequence (MIMS), and Minimum Information about a Marker Genemore » Sequence (MIMARKS). Community-wide adoption of MISAG and MIMAG will facilitate more robust comparative genomic analyses of bacterial and archaeal diversity.« less

Minimum information about a single amplified genome (MISAG) and a metagenome-assembled genome (MIMAG) of bacteria and archaea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowers, Robert M.; Kyrpides, Nikos C.; Stepanauskas, Ramunas

Here, we present two standards developed by the Genomic Standards Consortium (GSC) for reporting bacterial and archaeal genome sequences. Both are extensions of the Minimum Information about Any (x) Sequence (MIxS). The standards are the Minimum Information about a Single Amplified Genome (MISAG) and the Minimum Information about a MetagenomeAssembled Genome (MIMAG), including, but not limited to, assembly quality, and estimates of genome completeness and contamination. These standards can be used in combination with other GSC checklists, including the Minimum Information about a Genome Sequence (MIGS), Minimum Information about a Metagenomic Sequence (MIMS), and Minimum Information about a Marker Genemore » Sequence (MIMARKS). Community-wide adoption of MISAG and MIMAG will facilitate more robust comparative genomic analyses of bacterial and archaeal diversity.« less

Accessory costs of seed production and the evolution of angiosperms.

PubMed

Lord, Janice M; Westoby, Mark

2012-01-01

Accessory costs of reproduction frequently equal or exceed direct investment in offspring, and can limit the evolution of small offspring sizes. Early angiosperms had minimum seed sizes, an order of magnitude smaller than their contemporaries. It has been proposed that changes to reproductive features at the base of the angiosperm clade reduced accessory costs thus removing the fitness disadvantage of small seeds. We measured accessory costs of reproduction in 25 extant gymnosperms and angiosperms, to test whether angiosperms can produce small seeds more economically than gymnosperms. Total accessory costs scaled isometrically to seed mass for angiosperms but less than isometrically for gymnosperms, so that smaller seeds were proportionally more expensive for gymnosperms to produce. In particular, costs of abortions and packaging structures were significantly higher in gymnosperms. Also, the relationship between seed:ovule ratio and seed size was negative in angiosperms but positive in gymnosperms. We argue that the carpel was a key evolutionary innovation reducing accessory costs in angiosperms by allowing sporophytic control of pre- and postzygotic mate selection and timing of resource allocation. The resulting reduction in costs of aborting unfertilized ovules or genetically inferior embryos would have lowered total reproductive costs enabling early angiosperms to evolve small seed sizes and short generation times. © 2011 The Author(s). Evolution © 2011 The Society for the Study of Evolution.

Implications of Liebig’s law of the minimum for tree-ring reconstructions of climate

NASA Astrophysics Data System (ADS)

Stine, A. R.; Huybers, P.

2017-11-01

A basic principle of ecology, known as Liebig’s Law of the Minimum, is that plant growth reflects the strongest limiting environmental factor. This principle implies that a limiting environmental factor can be inferred from historical growth and, in dendrochronology, such reconstruction is generally achieved by averaging collections of standardized tree-ring records. Averaging is optimal if growth reflects a single limiting factor and noise but not if growth also reflects locally variable stresses that intermittently limit growth. In this study a collection of Arctic tree ring records is shown to follow scaling relationships that are inconsistent with the signal-plus-noise model of tree growth but consistent with Liebig’s Law acting at the local level. Also consistent with law-of-the-minimum behavior is that reconstructions based on the least-stressed trees in a given year better-follow variations in temperature than typical approaches where all tree-ring records are averaged. Improvements in reconstruction skill occur across all frequencies, with the greatest increase at the lowest frequencies. More comprehensive statistical-ecological models of tree growth may offer further improvement in reconstruction skill.

Uncertainty in Population Estimates for Endangered Animals and Improving the Recovery Process

PubMed Central

Haines, Aaron M.; Zak, Matthew; Hammond, Katie; Scott, J. Michael; Goble, Dale D.; Rachlow, Janet L.

2013-01-01

Simple Summary The objective of our study was to evaluate the mention of uncertainty (i.e., variance) associated with population size estimates within U.S. recovery plans for endangered animals. To do this we reviewed all finalized recovery plans for listed terrestrial vertebrate species. We found that more recent recovery plans reported more estimates of population size and uncertainty. Also, bird and mammal recovery plans reported more estimates of population size and uncertainty. We recommend that updated recovery plans combine uncertainty of population size estimates with a minimum detectable difference to aid in successful recovery. Abstract United States recovery plans contain biological information for a species listed under the Endangered Species Act and specify recovery criteria to provide basis for species recovery. The objective of our study was to evaluate whether recovery plans provide uncertainty (e.g., variance) with estimates of population size. We reviewed all finalized recovery plans for listed terrestrial vertebrate species to record the following data: (1) if a current population size was given, (2) if a measure of uncertainty or variance was associated with current estimates of population size and (3) if population size was stipulated for recovery. We found that 59% of completed recovery plans specified a current population size, 14.5% specified a variance for the current population size estimate and 43% specified population size as a recovery criterion. More recent recovery plans reported more estimates of current population size, uncertainty and population size as a recovery criterion. Also, bird and mammal recovery plans reported more estimates of population size and uncertainty compared to reptiles and amphibians. We suggest the use of calculating minimum detectable differences to improve confidence when delisting endangered animals and we identified incentives for individuals to get involved in recovery planning to improve access to quantitative data. PMID:26479531

Optimizing probability of detection point estimate demonstration

NASA Astrophysics Data System (ADS)

Koshti, Ajay M.

2017-04-01

The paper provides discussion on optimizing probability of detection (POD) demonstration experiments using point estimate method. The optimization is performed to provide acceptable value for probability of passing demonstration (PPD) and achieving acceptable value for probability of false (POF) calls while keeping the flaw sizes in the set as small as possible. POD Point estimate method is used by NASA for qualifying special NDE procedures. The point estimate method uses binomial distribution for probability density. Normally, a set of 29 flaws of same size within some tolerance are used in the demonstration. Traditionally largest flaw size in the set is considered to be a conservative estimate of the flaw size with minimum 90% probability and 95% confidence. The flaw size is denoted as α90/95PE. The paper investigates relationship between range of flaw sizes in relation to α90, i.e. 90% probability flaw size, to provide a desired PPD. The range of flaw sizes is expressed as a proportion of the standard deviation of the probability density distribution. Difference between median or average of the 29 flaws and α90 is also expressed as a proportion of standard deviation of the probability density distribution. In general, it is concluded that, if probability of detection increases with flaw size, average of 29 flaw sizes would always be larger than or equal to α90 and is an acceptable measure of α90/95PE. If NDE technique has sufficient sensitivity and signal-to-noise ratio, then the 29 flaw-set can be optimized to meet requirements of minimum required PPD, maximum allowable POF, requirements on flaw size tolerance about mean flaw size and flaw size detectability requirements. The paper provides procedure for optimizing flaw sizes in the point estimate demonstration flaw-set.

Relation between Streamflow of Swiftcurrent Creek, Montana, and the Geometry of Passage for Bull Trout (Salvelinus confluentus)

USGS Publications Warehouse

Auble, Gregor T.; Holmquist-Johnson, Christopher L.; Mogen, Jim T.; Kaeding, Lynn R.; Bowen, Zachary H.

2009-01-01

Operation of Sherburne Dam in northcentral Montana has typically reduced winter streamflow in Swiftcurrent Creek downstream of the dam and resulted in passage limitations for bull trout (Salvelinus confluentus). We defined an empirical relation between discharge in Swiftcurrent Creek between Sherburne Dam and the downstream confluence with Boulder Creek and fish passage geometry by considering how the cross-sectional area of water changed as a function of discharge at a set of cross sections likely to limit fish passage. With a minimum passage window of 15 x 45 cm, passage at the cross sections increased strongly with discharge over the range of 1.2 to 24 cfs. Most cross sections did not satisfy the minimum criteria at 1.2 cfs, 25 percent had no passage at 12.7 cfs, whereas at 24 cfs all but one of 26 cross sections had some passage and 90 percent had more than 3 m of width satisfying the minimum criteria. Sensitivity analysis suggests that the overall results are not highly dependent on exact dimensions of the minimum passage window. Combining these results with estimates of natural streamflow in the study reach further suggests that natural streamflow provided adequate passage at some times in most months and locations in the study reach, although not for all individual days and locations. Limitations of our analysis include assumptions about minimum passage geometry, measurement error, limitations of the cross-sectional model we used to characterize passage, the relation of Sherburne Dam releases to streamflow in the downstream study reach in the presence of ephemeral accretions, and the relation of passage geometry as we have measured it to fish responses of movement, stranding, and mortality, especially in the presence of ice cover.

Optimal Sizing and Placement of Battery Energy Storage in Distribution System Based on Solar Size for Voltage Regulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nazaripouya, Hamidreza; Wang, Yubo; Chu, Peter

2016-07-26

This paper proposes a new strategy to achieve voltage regulation in distributed power systems in the presence of solar energy sources and battery storage systems. The goal is to find the minimum size of battery storage and its corresponding location in the network based on the size and place of the integrated solar generation. The proposed method formulates the problem by employing the network impedance matrix to obtain an analytical solution instead of using a recursive algorithm such as power flow. The required modifications for modeling the slack and PV buses (generator buses) are utilized to increase the accuracy ofmore » the approach. The use of reactive power control to regulate the voltage regulation is not always an optimal solution as in distribution systems R/X is large. In this paper the minimum size and the best place of battery storage is achieved by optimizing the amount of both active and reactive power exchanged by battery storage and its gridtie inverter (GTI) based on the network topology and R/X ratios in the distribution system. Simulation results for the IEEE 14-bus system verify the effectiveness of the proposed approach.« less

The role of the National Launch System in support of Space Station Freedom

NASA Technical Reports Server (NTRS)

Green, J. L.; Saucillo, R. J.; Cirillo, W. M.

1992-01-01

A study was performed to determine the most appropriate potential use of the National Launch System (NLS) for Space Station Freedom (SSF) logistics resupply and growth assembly needs. Objectives were to estimate earth-to-SSF cargo requirements, identify NLS sizing trades, and assess operational constraints of a shuttle and NLS transportation infrastructure. Detailed NLS and Shuttle flight manifests were developed to model varying levels of NLS support. NLS delivery of SSF propellant, and in some cases, cryoenic fluids, yield significant shuttle flight savings with minimum impact to the baseline SSF design. Additional cargo can be delivered by the NLS if SSF trash disposal techniques are employed to limit return cargo requirements. A common vehicle performance level can be used for both logistics resupply and growth hardware delivery.

Nearest Neighbor Algorithms for Pattern Classification

NASA Technical Reports Server (NTRS)

Barrios, J. O.

1972-01-01

A solution of the discrimination problem is considered by means of the minimum distance classifier, commonly referred to as the nearest neighbor (NN) rule. The NN rule is nonparametric, or distribution free, in the sense that it does not depend on any assumptions about the underlying statistics for its application. The k-NN rule is a procedure that assigns an observation vector z to a category F if most of the k nearby observations x sub i are elements of F. The condensed nearest neighbor (CNN) rule may be used to reduce the size of the training set required categorize The Bayes risk serves merely as a reference-the limit of excellence beyond which it is not possible to go. The NN rule is bounded below by the Bayes risk and above by twice the Bayes risk.

Critical aspect ratio for tungsten fibers in copper-nickel matrix composites

NASA Technical Reports Server (NTRS)

Jech, R. W.

1975-01-01

Stress-rupture and tensile tests were conducted at 816 C (1500 F) to determine the effect of matrix composition on the minimum fiber length to diameter ratio (critical aspect ratio) below which fibers in a tungsten fiber/copper-nickel alloy matrix composite could not be stressed to their ultimate load carrying capability. This study was intended to simulate some of the conditions that might be encountered with materials combinations used in high-temperature composites. The critical aspect ratio for stress-rupture was found to be greater than for short-time tension, and it increased as the time to rupture increased. The increase was relatively slight, and calculated fiber lengths for long service appear to be well within practical size limits for effective reinforcement and ease of fabrication of potential gas turbine components.

Transition to collective oscillations in finite Kuramoto ensembles

NASA Astrophysics Data System (ADS)

Peter, Franziska; Pikovsky, Arkady

2018-03-01

We present an alternative approach to finite-size effects around the synchronization transition in the standard Kuramoto model. Our main focus lies on the conditions under which a collective oscillatory mode is well defined. For this purpose, the minimal value of the amplitude of the complex Kuramoto order parameter appears as a proper indicator. The dependence of this minimum on coupling strength varies due to sampling variations and correlates with the sample kurtosis of the natural frequency distribution. The skewness of the frequency sample determines the frequency of the resulting collective mode. The effects of kurtosis and skewness hold in the thermodynamic limit of infinite ensembles. We prove this by integrating a self-consistency equation for the complex Kuramoto order parameter for two families of distributions with controlled kurtosis and skewness, respectively.

Mapping the universe.

PubMed

Geller, M J; Huchra, J P

1989-11-17

Maps of the galaxy distribution in the nearby universe reveal large coherent structures. The extent of the largest features is limited only by the size of the survey. Voids with a density typically 20 percent of the mean and with diameters of 5000 km s(-1) are present in every survey large enough to contain them. Many galaxies lie in thin sheet-like structures. The largest sheet detected so far is the "Great Wall" with a minimum extent of 60 h(-1) Mpc x 170 h(-1) Mpc, where h is the Hubble constant in units of 100 km s(-1) Mpc(-1). The frequent occurrence of these structures is one of several serious challenges to our current understanding of the origin and evolution of the large-scale distribution of matter in the universe.

USING SUSTAINABILITY CRITERIA TO GUIDE LAND-USE DECISIONS

EPA Science Inventory

Human society and our economic systems are limited by the capacities of natural systems, and the sustainability of natural systems will be dependent upon the attainment of undetermined but minimum conditions of social and economic systems. These minimum conditions of intact econo...

41 CFR 101-25.301 - General.

Code of Federal Regulations, 2010 CFR

2010-07-01

... which shall be applied by all executive agencies. Additional criteria above these minimum standards shall be established by each executive agency, limiting its property to the minimum requirements necessary for the efficient functioning of the particular office concerned. This subpart does not apply to...

Survey of Occupational Noise Exposure in CF Personnel in Selected High-Risk Trades

DTIC Science & Technology

2003-11-01

peak, maximum level , minimum level , average sound level , time weighted average, dose, projected 8-hour dose, and upper limit time were measured for...10 4.4.2 Maximum Sound Level ...11 4.4.3 Minimum Sound Level

Computation of distribution of minimum resolution for log-normal distribution of chromatographic peak heights.

PubMed

Davis, Joe M

2011-10-28

General equations are derived for the distribution of minimum resolution between two chromatographic peaks, when peak heights in a multi-component chromatogram follow a continuous statistical distribution. The derivation draws on published theory by relating the area under the distribution of minimum resolution to the area under the distribution of the ratio of peak heights, which in turn is derived from the peak-height distribution. Two procedures are proposed for the equations' numerical solution. The procedures are applied to the log-normal distribution, which recently was reported to describe the distribution of component concentrations in three complex natural mixtures. For published statistical parameters of these mixtures, the distribution of minimum resolution is similar to that for the commonly assumed exponential distribution of peak heights used in statistical-overlap theory. However, these two distributions of minimum resolution can differ markedly, depending on the scale parameter of the log-normal distribution. Theory for the computation of the distribution of minimum resolution is extended to other cases of interest. With the log-normal distribution of peak heights as an example, the distribution of minimum resolution is computed when small peaks are lost due to noise or detection limits, and when the height of at least one peak is less than an upper limit. The distribution of minimum resolution shifts slightly to lower resolution values in the first case and to markedly larger resolution values in the second one. The theory and numerical procedure are confirmed by Monte Carlo simulation. Copyright © 2011 Elsevier B.V. All rights reserved.

Asteroid size distributions for the main belt and for asteroid families

NASA Astrophysics Data System (ADS)

Kazantzev, A.; Kazantzeva, L.

2017-12-01

The asteroid-size distribution for he Eos family was constructed. The WISE database containing the albedo p and the size D of over 80,000 asteroids was used. The b parameter of the power-law dependence has a minimum at some average values of the asteroid size of the family. A similar dependence b(D) exists for the whole asteroid belt. An assumption on the possible similarity of the formation mechanisms of the asteroid belt as a whole and separate families is made.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, H; Guerrero, M; Prado, K

Purpose: Building up a TG-71 based electron monitor-unit (MU) calculation protocol usually involves massive measurements. This work investigates a minimum data set of measurements and its calculation accuracy and measurement time. Methods: For 6, 9, 12, 16, and 20 MeV of our Varian Clinac-Series linear accelerators, the complete measurements were performed at different depth using 5 square applicators (6, 10, 15, 20 and 25 cm) with different cutouts (2, 3, 4, 6, 10, 15 and 20 cm up to applicator size) for 5 different SSD’s. For each energy, there were 8 PDD scans and 150 point measurements for applicator factors,more » cutout factors and effective SSDs that were then converted to air-gap factors for SSD 99–110cm. The dependence of each dosimetric quantity on field size and SSD was examined to determine the minimum data set of measurements as a subset of the complete measurements. The “missing” data excluded in the minimum data set were approximated by linear or polynomial fitting functions based on the included data. The total measurement time and the calculated electron MU using the minimum and the complete data sets were compared. Results: The minimum data set includes 4 or 5 PDD’s and 51 to 66 point measurements for each electron energy, and more PDD’s and fewer point measurements are generally needed as energy increases. Using only <50% of complete measurement time, the minimum data set generates acceptable MU calculation results compared to those with the complete data set. The PDD difference is within 1 mm and the calculated MU difference is less than 1.5%. Conclusion: Data set measurement for TG-71 electron MU calculations can be minimized based on the knowledge of how each dosimetric quantity depends on various setup parameters. The suggested minimum data set allows acceptable MU calculation accuracy and shortens measurement time by a few hours.« less

77 FR 20867 - Self-Regulatory Organizations; NASDAQ OMX PHLX LLC; Notice of Filing and Immediate Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-06

... Index, Equity and Currency Options) to extend a pilot program that eliminates minimum value sizes for... FLEX Options, FLEX currency options are also traded on the Exchange. These flexible index, equity, and currency options provide investors the ability to customize basic option features including size...

77 FR 33796 - Self-Regulatory Organizations; NASDAQ OMX PHLX LLC; Notice of Filing and Immediate Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-07

... Index, Equity and Currency Options) to extend a pilot program that eliminates minimum value sizes for... FLEX Options, FLEX currency options are also traded on the Exchange. These flexible index, equity, and currency options provide investors the ability to customize basic option features including size...

Crown size relationships for black willow in the Lower Mississippi Alluvial Valley

Treesearch

Jamie L. Schuler; Bradley Woods; Joshua Adams; Ray Souter

2015-01-01

Growing space requirements derived from maximum and minimum crown sizes have been identified for many southern hardwood species. These requirements help managers assess stocking levels, schedule intermediate treatments, and even assist in determining planting densities. Throughout the Mississippi Alluvial Valley, black willow (Salix nigra Marsh.) stands are common...

78 FR 68893 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

... the minimum quotation sizes (or ``tier sizes'') for OTC equity securities \\4\\ to, among other things... depth (dollar value of shares) at the inside. Amendment No. 2 specified, among other things, that: (1...\\ which requires, among other things, that FINRA rules must be designed to prevent fraudulent and...

40 CFR Figure C-4 to Subpart C of... - Illustration of the Minimum Limits for Correlation Coefficient for PM 2.5 and PM 10-2,5 Class II...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Illustration of the Minimum Limits for Correlation Coefficient for PM 2.5 and PM 10-2,5 Class II and III Methods C Figure C-4 to Subpart C of Part 53... Methods and Reference Methods Pt. 53, Subpt. C, Fig. C-4 Figure C-4 to Subpart C of Part 53—Illustration...

40 CFR Figure C-4 to Subpart C of... - Illustration of the Minimum Limits for Correlation Coefficient for PM 2.5 and PM 10-2.5 Class II...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Illustration of the Minimum Limits for Correlation Coefficient for PM 2.5 and PM 10-2.5 Class II and III Methods C Figure C-4 to Subpart C of Part 53... Methods and Reference Methods Pt. 53, Subpt. C, Fig. C-4 Figure C-4 to Subpart C of Part 53—Illustration...

Wavefront control of high-power laser beams in the National Ignition Facility (NIF)

NASA Astrophysics Data System (ADS)

Zacharias, Richard A.; Bliss, Erlan S.; Winters, Scott; Sacks, Richard A.; Feldman, Mark; Grey, Andrew; Koch, Jeffrey A.; Stolz, Christopher J.; Toeppen, John S.; Van Atta, Lewis; Woods, Bruce W.

2000-04-01

The use of lasers as the driver for inertial confinement fusion and weapons physics experiments is based on their ability to produce high-energy short pulses in a beam with low divergence. Indeed, the focusability of high quality laser beams far exceeds alternate technologies and is a major factor in the rationale for building high power lasers for such applications. The National Ignition Facility (NIF) is a large, 192-beam, high-power laser facility under construction at the Lawrence Livermore National Laboratory for fusion and weapons physics experiments. Its uncorrected minimum focal spot size is limited by laser system aberrations. The NIF includes a Wavefront Control System to correct these aberrations to yield a focal spot small enough for its applications. Sources of aberrations to be corrected include prompt pump-induced distortions in the laser amplifiers, previous-shot thermal distortions, beam off-axis effects, and gravity, mounting, and coating-induced optic distortions. Aberrations from gas density variations and optic-manufacturing figure errors are also partially corrected. This paper provides an overview of the NIF Wavefront Control System and describes the target spot size performance improvement it affords. It describes provisions made to accommodate the NIF's high fluence (laser beam and flashlamp), large wavefront correction range, wavefront temporal bandwidth, temperature and humidity variations, cleanliness requirements, and exception handling requirements (e.g. wavefront out-of-limits conditions).

Comparative evaluation of distributed-collector solar thermal electric power plants

NASA Technical Reports Server (NTRS)

Fujita, T.; El Gabalawi, N.; Herrera, G. G.; Caputo, R. S.

1978-01-01

Distributed-collector solar thermal-electric power plants are compared by projecting power plant economics of selected systems to the 1990-2000 timeframe. The approach taken is to evaluate the performance of the selected systems under the same weather conditions. Capital and operational costs are estimated for each system. Energy costs are calculated for different plant sizes based on the plant performance and the corresponding capital and maintenance costs. Optimum systems are then determined as the systems with the minimum energy costs for a given load factor. The optimum system is comprised of the best combination of subsystems which give the minimum energy cost for every plant size. Sensitivity analysis is done around the optimum point for various plant parameters.

Efficiency calibration and minimum detectable activity concentration of a real-time UAV airborne sensor system with two gamma spectrometers.

PubMed

Tang, Xiao-Bin; Meng, Jia; Wang, Peng; Cao, Ye; Huang, Xi; Wen, Liang-Sheng; Chen, Da

2016-04-01

A small-sized UAV (NH-UAV) airborne system with two gamma spectrometers (LaBr3 detector and HPGe detector) was developed to monitor activity concentration in serious nuclear accidents, such as the Fukushima nuclear accident. The efficiency calibration and determination of minimum detectable activity concentration (MDAC) of the specific system were studied by MC simulations at different flight altitudes, different horizontal distances from the detection position to the source term center and different source term sizes. Both air and ground radiation were considered in the models. The results obtained may provide instructive suggestions for in-situ radioactivity measurements of NH-UAV. Copyright © 2016 Elsevier Ltd. All rights reserved.

Behavior and Microstructure in Cryomilled Aluminum alloy Containing Diamondoids Nanoparticles

NASA Astrophysics Data System (ADS)

Hanna, Walid Magdy

Aluminum (Al) alloys have been the materials of choice for both civil and military aircraft structure. Primary among these alloys are 6061 Al and 5083 Al, which have used for several structural applications including those in aerospace and automobile industry. It is desirable to enhance strength in Al alloys beyond that achieved via traditional techniques such as precipitation hardening. Recent developments have indicated strengthening via grain refinement is an effective approach since, according the Hall-Petch relation, as grain size decreases strength significantly increases. The innovate techniques of severe plastic deformation, cryomilling, are successful in reefing grain size. These techniques lead to a minimum grain size that is the result of a dynamic balance between the formation of dislocation structure and its recovery by thermal processes. According to Mohamed's model, each metal is characterized by a minimum grain size that is determined by materials parameters such as the stacking faulty energy and the activation energy for diffusion. In the present dissertation, 6061 Al and 5083 Al were synthesized using cryomilling. Microstructural characterization was extensively carried out to monitor grain size changes. A close examination of the morphology of the 6061 Al powder particles revealed that in the early milling stages, the majority of the particles changed from spheres to thin disk-shaped particles. This change was attributed to the high degree of plastic deformation generated by the impact energy during ball-powder-ball collisions. Both transmission electron microscopy (TEM) and X-ray diffraction (XRD) were used to monitor the change in grain size as a function of milling time. The results of both techniques demonstrated a close agreement with respect to two observations: (a) during cryomilling, the grain size of 6061 Al decreased with milling time, and (b) after 15 h of milling, the grain size approached a minimum value of about 22 nm, which is in the range reported for Al (18 nm--24 nm). Despite this agreement, there was a discrepancy: for grain sizes > 40 nm, the grain size measured by TEM was appreciably larger that inferred from XRD. It was suggested that this discrepancy was most likely related to the limitation for accurately measuring grain sizes > 100 nm by the technique of XRD. It was reported that the average grain size of the as-milled powders of 5083 Al alloy was about 20 nm, and that when the as-milled powders were exposed to elevated temperatures or consolidated via hot isostatic pressing and extruded, the average grain size increased to about 250 nm. Very recent results have indicated the success of maintaining the thermal stability of Al by adding diamantane during milling. 5083 Al powders were cryomilled with 0.5 wt. % diamantane for 8 hours producing mechanically alloyed powders with an average grain size of 17 nm. The grain size remained nanocrystalline (less than100 nm) for Al 5083 alloy with 0.5% diamantane, even after 48 h at the highest temperature of 773 K. The Effect of Diamantane on the thermal stability of cryomilled nanocrystalline 5083 Al alloy was investigated by heating the powder in an inert gas atmosphere at temperature range from 473K to 773K for time interval between 0.5 hr. to 48 hr. The average grain size was observed to be in nano scale range less than 100 nm. The thermal stability results were found to be consistent with the grain growth model based on drag forces exerted by dispersed particles against grain boundary migration (Burke model). As observed for other cryomilled Al alloys, two grain growth regimes were identified using this model: one at relatively low temperatures (473--623 K) where the activation energy is about 1.9 kJ/mole and another at higher temperatures where the activation energy is about 18 kJ/mole. The presence of the former region was explained in terms of stress relaxation facilitated by less stable processes such as recovery of dislocation segments or sub-boundary remnants while the latter region was attributed to grain boundary realignment annihilation of grain boundary remnants.

Charge carrier concentration dependence of encounter-limited bimolecular recombination in phase-separated organic semiconductor blends

NASA Astrophysics Data System (ADS)

Heiber, Michael C.; Nguyen, Thuc-Quyen; Deibel, Carsten

2016-05-01

Understanding how the complex intermolecular configurations and nanostructure present in organic semiconductor donor-acceptor blends impacts charge carrier motion, interactions, and recombination behavior is a critical fundamental issue with a particularly major impact on organic photovoltaic applications. In this study, kinetic Monte Carlo (KMC) simulations are used to numerically quantify the complex bimolecular charge carrier recombination behavior in idealized phase-separated blends. Recent KMC simulations have identified how the encounter-limited bimolecular recombination rate in these blends deviates from the often used Langevin model and have been used to construct the new power mean mobility model. Here, we make a challenging but crucial expansion to this work by determining the charge carrier concentration dependence of the encounter-limited bimolecular recombination coefficient. In doing so, we find that an accurate treatment of the long-range electrostatic interactions between charge carriers is critical, and we further argue that many previous KMC simulation studies have used a Coulomb cutoff radius that is too small, which causes a significant overestimation of the recombination rate. To shed more light on this issue, we determine the minimum cutoff radius required to reach an accuracy of less than ±10 % as a function of the domain size and the charge carrier concentration and then use this knowledge to accurately quantify the charge carrier concentration dependence of the recombination rate. Using these rigorous methods, we finally show that the parameters of the power mean mobility model are determined by a newly identified dimensionless ratio of the domain size to the average charge carrier separation distance.

Expected effects of reducing Oestrus ovis L. mature larval weight on adult populations.

PubMed

Cepeda-Palacios, R; Frugère, S; Dorchies, P

2000-06-27

In order to estimate the effects of eventual reductions in larval weight (LW) of Oestrus ovis L. as a measure of control, the correlation between mature LW and adult fly length (AL) in laboratory specimens (n=150) was calculated. The regression equation AL=5.62+10.65LW (r(2)=0.76) was obtained. This equation was then applied to estimate the mature LW of wild larvipositing females (n=51) to predict the minimum mature LW at which fly viability would be compromised. The critical weight, 0.28 g (standard error limits 0. 235, 0.323), was obtained from a small fly measuring 8.6mm in length. Data from 383 mature third instars were used to estimate, by statistical analysis, the expected effects of decreasing the mature LW on subsequent fly population size. A considerable mean reduction (38%) in adult populations might be achieved by a 40% reduction of mature LW, but this eventual reduction may be temporary due to the high reproductive rate in this species. Sex differences in mature LW and fly size are also reported.

Further miniaturisation of the Thermochron iButton to create a thermal bio-logger weighing 0.3 g.

PubMed

Virens, Josef; Cree, Alison

2018-06-05

Thermochron iButtons are commonly used by thermal biologists to continuously measure body temperature from animals. However, if unmodified, these devices are of a size that limits their use with very small animals. To allow iButtons to be used to study smaller species, methods to miniaturise them by 61% have been previously described. We present a method to reduce iButton mass by a further 71%. The modified devices have a shorter battery life, but the minimum size of vertebrates able to carry the devices is reduced from 28.9 g to 6.6 g, if the arbitrary, yet widely cited, maximum of 5% body mass for attached devices is adhered to. We demonstrate the application of our method by recording surface temperatures of captive and wild skinks and show that captive cockroaches weighing 0.8 g are also able to carry the device. We believe this to be the first time that temperature data have been recorded from an insect in this way. © 2018. Published by The Company of Biologists Ltd.

Simultaneous infrared and optical observations of the transiting debris cloud around WD 1145+017

NASA Astrophysics Data System (ADS)

Zhou, G.; Kedziora-Chudczer, L.; Bailey, J.; Marshall, J. P.; Bayliss, D. D. R.; Stockdale, C.; Nelson, P.; Tan, T. G.; Rodriguez, J. E.; Tinney, C. G.; Dragomir, D.; Colon, K.; Shporer, A.; Bento, J.; Sefako, R.; Horne, K.; Cochran, W.

2016-12-01

We present multiwavelength photometric monitoring of WD 1145+017, a white dwarf exhibiting periodic dimming events interpreted to be the transits of orbiting, disintegrating planetesimals. Our observations include the first set of near-infrared light curves for the object, obtained on multiple nights over the span of 1 month, and recorded multiple transit events with depths varying between ˜20 and 50 per cent. Simultaneous near-infrared and optical observations of the deepest and longest duration transit event were obtained on two epochs with the Anglo-Australian Telescope and three optical facilities, over the wavelength range of 0.5-1.2 μm. These observations revealed no measurable difference in transit depths for multiple photometric pass bands, allowing us to place a 2σ lower limit of 0.8 μm on the grain size in the putative transiting debris cloud. This conclusion is consistent with the spectral energy distribution of the system, which can be fit with an optically thin debris disc with minimum particle sizes of 10^{+5}_{-3} μm.

High-Throughput Fabrication of Ultradense Annular Nanogap Arrays for Plasmon-Enhanced Spectroscopy.

PubMed

Cai, Hongbing; Meng, Qiushi; Zhao, Hui; Li, Mingling; Dai, Yanmeng; Lin, Yue; Ding, Huaiyi; Pan, Nan; Tian, Yangchao; Luo, Yi; Wang, Xiaoping

2018-06-13

The confinement of light into nanometer-sized metallic nanogaps can lead to an extremely high field enhancement, resulting in dramatically enhanced absorption, emission, and surface-enhanced Raman scattering (SERS) of molecules embedded in nanogaps. However, low-cost, high-throughput, and reliable fabrication of ultra-high-dense nanogap arrays with precise control of the gap size still remains a challenge. Here, by combining colloidal lithography and atomic layer deposition technique, a reproducible method for fabricating ultra-high-dense arrays of hexagonal close-packed annular nanogaps over large areas is demonstrated. The annular nanogap arrays with a minimum diameter smaller than 100 nm and sub-1 nm gap width have been produced, showing excellent SERS performance with a typical enhancement factor up to 3.1 × 10 6 and a detection limit of 10 -11 M. Moreover, it can also work as a high-quality field enhancement substrate for studying two-dimensional materials, such as MoSe 2 . Our method provides an attractive approach to produce controllable nanogaps for enhanced light-matter interaction at the nanoscale.

40 CFR Table 6 to Subpart Dddd of... - Model Rule-Emission Limitations That Apply to Incinerators on and After [Date to be specified in...

Code of Federal Regulations, 2012 CFR

2012-07-01

... per million dry volume 3-run average (1 hour minimum sample time per run) Performance test (Method 10... (Reapproved 2008) c. Oxides of nitrogen 53 parts per million dry volume 3-run average (1 hour minimum sample... average (1 hour minimum sample time per run) Performance test (Method 6 or 6c at 40 CFR part 60, appendix...

40 CFR Table 6 to Subpart Dddd of... - Model Rule-Emission Limitations That Apply to Incinerators on and After [Date to be specified in...

Code of Federal Regulations, 2011 CFR

2011-07-01

... per million dry volume 3-run average (1 hour minimum sample time per run) Performance test (Method 10... (Reapproved 2008) c. Oxides of nitrogen 53 parts per million dry volume 3-run average (1 hour minimum sample... average (1 hour minimum sample time per run) Performance test (Method 6 or 6c at 40 CFR part 60, appendix...

40 CFR Table 2 to Subpart Dddd of... - Model Rule-Emission Limitations That Apply to Incinerators Before [Date to be specified in state...

Code of Federal Regulations, 2014 CFR

2014-07-01

... parts per million by dry volume 3-run average (1 hour minimum sample time per run) Performance test..., appendix A-4). Oxides of nitrogen 388 parts per million by dry volume 3-run average (1 hour minimum sample... (1 hour minimum sample time per run) Performance test (Method 6 or 6c of appendix A of this part) a...

40 CFR Table 2 to Subpart Dddd of... - Model Rule-Emission Limitations That Apply to Incinerators Before [Date to be specified in state...

Code of Federal Regulations, 2013 CFR

2013-07-01

... parts per million by dry volume 3-run average (1 hour minimum sample time per run) Performance test..., appendix A-4). Oxides of nitrogen 388 parts per million by dry volume 3-run average (1 hour minimum sample... (1 hour minimum sample time per run) Performance test (Method 6 or 6c of appendix A of this part) a...

Brief Report: Investigating Uncertainty in the Minimum Mortality Temperature: Methods and Application to 52 Spanish Cities.

PubMed

Tobías, Aurelio; Armstrong, Ben; Gasparrini, Antonio

2017-01-01

The minimum mortality temperature from J- or U-shaped curves varies across cities with different climates. This variation conveys information on adaptation, but ability to characterize is limited by the absence of a method to describe uncertainty in estimated minimum mortality temperatures. We propose an approximate parametric bootstrap estimator of confidence interval (CI) and standard error (SE) for the minimum mortality temperature from a temperature-mortality shape estimated by splines. The coverage of the estimated CIs was close to nominal value (95%) in the datasets simulated, although SEs were slightly high. Applying the method to 52 Spanish provincial capital cities showed larger minimum mortality temperatures in hotter cities, rising almost exactly at the same rate as annual mean temperature. The method proposed for computing CIs and SEs for minimums from spline curves allows comparing minimum mortality temperatures in different cities and investigating their associations with climate properly, allowing for estimation uncertainty.

Dilute-and-shoot coupled to nanoflow liquid chromatography high resolution mass spectrometry for the determination of drugs of abuse and sport drugs in human urine.

PubMed

Alcántara-Durán, Jaime; Moreno-González, David; Beneito-Cambra, Miriam; García-Reyes, Juan F

2018-05-15

In this work, a sensitive nanoflow liquid chromatography high-resolution mass spectrometry screening method has been developed for the determination of multiclass drugs of abuse and sport drugs in human urine. 81 drugs belonging to different multiclass pharmaceuticals were targeted. The method is based on the use of a nanoLC column (75 µm × 150 mm, 3 µm particle size and 100 Å pore) with the nanospray emitter tip integrated so that dead volumes are significantly minimized. Data acquisition method included both full-scan and all ion fragmentation experiments using an Orbitrap analyser (Q-Exactive) operated in the positive ionization mode. To increase laboratory throughput, a dilute-and-shoot methodology has been tested and proposed, based solely on direct urine dilution without further sample workup. Matrix effects were evaluated, showing a negligible effect for all studied compounds when a dilution 1:50 was implemented. Despite this high-dilution factor, limits of quantification were still satisfactory, with values below 5 µg L -1 in most cases, being lower than their minimum required performance limits correspond established by the World Anti-Doping Agency. Therefore, the use of the dilute-and-shoot method with the enhanced sensitivity provided by nanoflow LC setup could be useful tool for the determination of studied compounds in drug testing, thus increasing laboratory performance, because a minimum sample treatment steps are required. Copyright © 2018 Elsevier B.V. All rights reserved.

Photolithography-free laser-patterned HF acid-resistant chromium-polyimide mask for rapid fabrication of microfluidic systems in glass

NASA Astrophysics Data System (ADS)

Zamuruyev, Konstantin O.; Zrodnikov, Yuriy; Davis, Cristina E.

2017-01-01

Excellent chemical and physical properties of glass, over a range of operating conditions, make it a preferred material for chemical detection systems in analytical chemistry, biology, and the environmental sciences. However, it is often compromised with SU8, PDMS, or Parylene materials due to the sophisticated mask preparation requirements for wet etching of glass. Here, we report our efforts toward developing a photolithography-free laser-patterned hydrofluoric acid-resistant chromium-polyimide tape mask for rapid prototyping of microfluidic systems in glass. The patterns are defined in masking layer with a diode-pumped solid-state laser. Minimum feature size is limited to the diameter of the laser beam, 30 µm minimum spacing between features is limited by the thermal shrinkage and adhesive contact of the polyimide tape to 40 µm. The patterned glass substrates are etched in 49% hydrofluoric acid at ambient temperature with soft agitation (in time increments, up to 60 min duration). In spite of the simplicity, our method demonstrates comparable results to the other current more sophisticated masking methods in terms of the etched depth (up to 300 µm in borosilicate glass), feature under etch ratio in isotropic etch (~1.36), and low mask hole density. The method demonstrates high yield and reliability. To our knowledge, this method is the first proposed technique for rapid prototyping of microfluidic systems in glass with such high performance parameters. The proposed method of fabrication can potentially be implemented in research institutions without access to a standard clean-room facility.

Grain-size considerations for optoelectronic multistage interconnection networks.

PubMed

Krishnamoorthy, A V; Marchand, P J; Kiamilev, F E; Esener, S C

1992-09-10

This paper investigates, at the system level, the performance-cost trade-off between optical and electronic interconnects in an optoelectronic interconnection network. The specific system considered is a packet-switched, free-space optoelectronic shuffle-exchange multistage interconnection network (MIN). System bandwidth is used as the performance measure, while system area, system power, and system volume constitute the cost measures. A detailed design and analysis of a two-dimensional (2-D) optoelectronic shuffle-exchange routing network with variable grain size K is presented. The architecture permits the conventional 2 x 2 switches or grains to be generalized to larger K x K grain sizes by replacing optical interconnects with electronic wires without affecting the functionality of the system. Thus the system consists of log(k) N optoelectronic stages interconnected with free-space K-shuffles. When K = N, the MIN consists of a single electronic stage with optical input-output. The system design use an effi ient 2-D VLSI layout and a single diffractive optical element between stages to provide the 2-D K-shuffle interconnection. Results indicate that there is an optimum range of grain sizes that provides the best performance per cost. For the specific VLSI/GaAs multiple quantum well technology and system architecture considered, grain sizes larger than 256 x 256 result in a reduced performance, while grain sizes smaller than 16 x 16 have a high cost. For a network with 4096 channels, the useful range of grain sizes corresponds to approximately 250-400 electronic transistors per optical input-output channel. The effect of varying certain technology parameters such as the number of hologram phase levels, the modulator driving voltage, the minimum detectable power, and VLSI minimum feature size on the optimum grain-size system is studied. For instance, results show that using four phase levels for the interconnection hologram is a good compromise for the cost functions mentioned above. As VLSI minimum feature sizes decrease, the optimum grain size increases, whereas, if optical interconnect performance in terms of the detector power or modulator driving voltage requirements improves, the optimum grain size may be reduced. Finally, several architectural modifications to the system, such as K x K contention-free switches and sorting networks, are investigated and optimized for grain size. Results indicate that system bandwidth can be increased, but at the price of reduced performance/cost. The optoelectronic MIN architectures considered thus provide a broad range of performance/cost alternatives and offer a superior performance over purely electronic MIN's.

Pre-main Sequence Evolution and the Hydrogen-Burning Minimum Mass

NASA Astrophysics Data System (ADS)

Nakano, Takenori

There is a lower limit to the mass of the main-sequence stars (the hydrogen-burning minimum mass) below which the stars cannot replenish the energy lost from their surfaces with the energy released by the hydrogen burning in their cores. This is caused by the electron degeneracy in the stars which suppresses the increase of the central temperature with contraction. To find out the lower limit we need the accurate knowledge of the pre-main sequence evolution of very low-mass stars in which the effect of electron degeneracy is important. We review how Hayashi and Nakano (1963) carried out the first determination of this limit.

Length limits fail to restructure a Largemouth Bass population: A 28‐year case history

USGS Publications Warehouse

Miranda, Leandro E.; Colvin, M.E.; Shamaskin, A. C.; Bull, L. A.; Holman, T.; Jones, R.

2017-01-01

Length limits have been implemented by fisheries management agencies to achieve population density, size structure, and angler satisfaction objectives. By redirecting harvest towards or away from particular length‐ or age‐groups, length limits rely on harvest by anglers to maintain a population at or near a desired state. The fish population changes that follow the implementation of harvest regulations may take several years to manifest, so long‐term monitoring may be needed to adequately evaluate length limits. We used an innovative application of cluster analysis to facilitate evaluation of the effects of three consecutive length limits on a population of Largemouth Bass Micropterus salmoides over a 28‐year period in Ross Barnett Reservoir, Mississippi. A 13–16‐in protected slot length limit (10 years), followed by a 15‐in minimum length limit (MLL; 11 years), followed by a 12‐in MLL (7 years) failed to restructure the Largemouth Bass population due to what we suggest was the expansion of a voluntary catch‐and‐release attitude that started in the first decade of the study period. Various population metrics shifted towards values expected in an unharvested population, and the observed shifts can be attributed to a harvest deficit created by the prevailing catch‐and‐release attitude. Largemouth Bass harvest regulations may no longer be relevant in many waters. The utility of regulations for restructuring Largemouth Bass populations is largely dependent on harvesting attitudes that vary geographically, depending on cultural characteristics and demographics.

Magnetic permeability as a predictor of the artefact size caused by orthodontic appliances at 1.5 T magnetic resonance imaging.

PubMed

Blankenstein, Felix H; Asbach, Patrick; Beuer, Florian; Glienke, Johannes; Mayer, Stefan; Zachriat, Christine

2017-01-01

Artefacts caused by orthodontic attachments limit the diagnostic value and lead to removal of these appliances before magnetic resonance imaging. Magnetic permeability can predict the artefact size. There is no standardised approach to determine the permeability of such attachments. The aim was to establish a reliable approach to determine artefact size caused by orthodontic attachments at 1.5 T MRI. Artefact radii of 21 attachments were determined applying two prevalent sequences of the head and neck region (turbo spin echo and gradient echo). The instrument Ferromaster (Stefan Mayer Instruments, Dinslaken) is approved for permeability measurements of objects with a minimum size (d = 20 mm, h = 5 mm). Eleven small test specimens of known permeability between 1.003 and 1.431 were produced. They are slightly larger than the orthodontic attachments. Their artefacts were measured and cross tabulated against the permeability. The resulting curve was used to compare the orthodontic attachments with the test bodies. Steel caused a wide range of artefact size of 10-74 mm subject to their permeability. Titanium, cobalt-chromium and ceramic materials produced artefact radii up to 20 mm. Measurement of artefacts of the test bodies revealed an interrelationship according to a root function. The artefact size of all brackets was below that root function. The permeability can be reliably assessed by conventional measurement devices and the artefact size can be predicted. The radiologist is able to decide whether or not the orthodontic attachments should be removed. This study clarifies whether an orthodontic appliance must be removed before taking an MRI.

Modeling of the minimum variable blank holder force based on forming limit diagram (FLD) in deep drawing process

NASA Astrophysics Data System (ADS)

Candra, S.; Batan, I. M. L.; Berata, W.; Pramono, A. S.

2017-11-01

This paper presents the mathematical approach of minimum blank holder force to prevent wrinkling in deep drawing process of the cylindrical cup. Based on the maximum of minor-major strain ratio, the slab method was applied to determine the modeling of minimum variable blank holder force (VBHF) and it compared to FE simulation. The Tin steel sheet of T4-CA grade, with the thickness of 0.2 mm was used in this study. The modeling of minimum VBHF can be used as a simple reference to prevent wrinkling in deep drawing.

Phylogenetic review of tonal sound production in whales in relation to sociality

PubMed Central

May-Collado, Laura J; Agnarsson, Ingi; Wartzok, Douglas

2007-01-01

Background It is widely held that in toothed whales, high frequency tonal sounds called 'whistles' evolved in association with 'sociality' because in delphinids they are used in a social context. Recently, whistles were hypothesized to be an evolutionary innovation of social dolphins (the 'dolphin hypothesis'). However, both 'whistles' and 'sociality' are broad concepts each representing a conglomerate of characters. Many non-delphinids, whether solitary or social, produce tonal sounds that share most of the acoustic characteristics of delphinid whistles. Furthermore, hypotheses of character correlation are best tested in a phylogenetic context, which has hitherto not been done. Here we summarize data from over 300 studies on cetacean tonal sounds and social structure and phylogenetically test existing hypotheses on their co-evolution. Results Whistles are 'complex' tonal sounds of toothed whales that demark a more inclusive clade than the social dolphins. Whistles are also used by some riverine species that live in simple societies, and have been lost twice within the social delphinoids, all observations that are inconsistent with the dolphin hypothesis as stated. However, cetacean tonal sounds and sociality are intertwined: (1) increased tonal sound modulation significantly correlates with group size and social structure; (2) changes in tonal sound complexity are significantly concentrated on social branches. Also, duration and minimum frequency correlate as do group size and mean minimum frequency. Conclusion Studying the evolutionary correlation of broad concepts, rather than that of their component characters, is fraught with difficulty, while limits of available data restrict the detail in which component character correlations can be analyzed in this case. Our results support the hypothesis that sociality influences the evolution of tonal sound complexity. The level of social and whistle complexity are correlated, suggesting that complex tonal sounds play an important role in social communication. Minimum frequency is higher in species with large groups, and correlates negatively with duration, which may reflect the increased distances over which non-social species communicate. Our findings are generally stable across a range of alternative phylogenies. Our study points to key species where future studies would be particularly valuable for enriching our understanding of the interplay of acoustic communication and sociality. PMID:17692128

Reconstruction of Absorbed Doses to Fibroglandular Tissue of the Breast of Women undergoing Mammography (1960 to the Present)

PubMed Central

Thierry-Chef, Isabelle; Simon, Steven L.; Weinstock, Robert M.; Kwon, Deukwoo; Linet, Martha S.

2013-01-01

The assessment of potential benefits versus harms from mammographic examinations as described in the controversial breast cancer screening recommendations of the U.S. Preventive Task Force included limited consideration of absorbed dose to the fibroglandular tissue of the breast (glandular tissue dose), the tissue at risk for breast cancer. Epidemiological studies on cancer risks associated with diagnostic radiological examinations often lack accurate information on glandular tissue dose, and there is a clear need for better estimates of these doses. Our objective was to develop a quantitative summary of glandular tissue doses from mammography by considering sources of variation over time in key parameters including imaging protocols, x-ray target materials, voltage, filtration, incident air kerma, compressed breast thickness, and breast composition. We estimated the minimum, maximum, and mean values for glandular tissue dose for populations of exposed women within 5-year periods from 1960 to the present, with the minimum to maximum range likely including 90% to 95% of the entirety of the dose range from mammography in North America and Europe. Glandular tissue dose from a single view in mammography is presently about 2 mGy, about one-sixth the dose in the 1960s. The ratio of our estimates of maximum to minimum glandular tissue doses for average-size breasts was about 100 in the 1960s compared to a ratio of about 5 in recent years. Findings from our analysis provide quantitative information on glandular tissue doses from mammographic examinations which can be used in epidemiologic studies of breast cancer. PMID:21988547

Strengthening materials specifications

NASA Astrophysics Data System (ADS)

Sampath, K.

2005-10-01

Continuing efforts to strengthen materials specifications readily recognize that a mere compliance with a materials specification only assures a material meeting or exceeding the minimum expectations explicitly detailed in the specification. Implicitly, such efforts also recognize that additional and specific client needs must be addressed as supplementary requirements and introduced during material procurement to reduce risks and assure enhanced performance. This article describes two U.S. Navy-related case studies that allowed further strengthening of the materials specification process, using newer methods and renewed understanding. The first case demonstrates the use of a constraints-based modeling approach to specify the chemical composition of high-performance welding electrodes for critical U.S. Navy applications. This approach helps to distinguish high-performance welding electrode chemical compositions from rich and lean welding electrode chemical compositions that might limit the operational envelope, reduce performance, or both, while increasing overall cost of fabrication but otherwise meet electrode specification requirements. The second case identifies that the size of an ingot could be an important factor while specifying the aluminum and sulfur contents of very large-size, heavy-gauge plates. Renewed understanding of melt fluidity issues associated with the solidification of very large-size ingots shows that deficiencies in through-thickness ductility of heavy-gauge plates are related to controlling aluminum and sulfur contents of the voluminous melt, notwithstanding explicit compliance with specification requirements.

Subcellular-level resolution MALDI-MS imaging of maize leaf metabolites by MALDI-linear ion trap-Orbitrap mass spectrometer

DOE PAGES

Korte, Andrew R.; Yandeau-Nelson, Marna D.; Nikolau, Basil J.; ...

2015-01-25

A significant limiting factor in achieving high spatial resolution for matrix-assisted laser desorption ionization-mass spectrometry (MALDI-MS) imaging is the size of the laser spot at the sample surface. We present modifications to the beam-delivery optics of a commercial MALDI-linear ion trap-Orbitrap instrument, incorporating an external Nd:YAG laser, beam-shaping optics, and an aspheric focusing lens, to reduce the minimum laser spot size from ~50 μm for the commercial configuration down to ~9 μm for the modified configuration. This improved system was applied for MALDI-MS imaging of cross sections of juvenile maize leaves at 5-μm spatial resolution using an oversampling method. Theremore » are a variety of different metabolites including amino acids, glycerolipids, and defense-related compounds were imaged at a spatial resolution well below the size of a single cell. Such images provide unprecedented insights into the metabolism associated with the different tissue types of the maize leaf, which is known to asymmetrically distribute the reactions of C4 photosynthesis among the mesophyll and bundle sheath cell types. The metabolite ion images correlate with the optical images that reveal the structures of the different tissues, and previously known and newly revealed asymmetric metabolic features are observed.« less

Coherent Doppler lidar for automated space vehicle rendezvous, stationkeeping and capture

NASA Technical Reports Server (NTRS)

Bilbro, James A.

1991-01-01

The inherent spatial resolution of laser radar makes ladar or lidar an attractive candidate for Automated Rendezvous and Capture application. Previous applications were based on incoherent lidar techniques, requiring retro-reflectors on the target vehicle. Technology improvements (reduced size, no cryogenic cooling requirement) have greatly enhanced the construction of coherent lidar systems. Coherent lidar permits the acquisition of non-cooperative targets at ranges that are limited by the detection capability rather than by the signal-to-noise ratio (SNR) requirements. The sensor can provide translational state information (range, velocity, and angle) by direct measurement and, when used with any array detector, also can provide attitude information by Doppler imaging techniques. Identification of the target is accomplished by scanning with a high pulse repetition frequency (dependent on the SNR). The system performance is independent of range and should not be constrained by sun angle. An initial effort to characterize a multi-element detection system has resulted in a system that is expected to work to a minimum range of 1 meter. The system size, weight and power requirements are dependent on the operating range; 10 km range requires a diameter of 3 centimeters with overall size at 3 x 3 x 15 to 30 cm, while 100 km range requires a 30 cm diameter.

Results and evaluation of a survey to estimate Pacific walrus population size, 2006

USGS Publications Warehouse

Speckman, Suzann G.; Chernook, Vladimir I.; Burn, Douglas M.; Udevitz, Mark S.; Kochnev, Anatoly A.; Vasilev, Alexander; Jay, Chadwick V.; Lisovsky, Alexander; Fischbach, Anthony S.; Benter, R. Bradley

2011-01-01

In spring 2006, we conducted a collaborative U.S.-Russia survey to estimate abundance of the Pacific walrus (Odobenus rosmarus divergens). The Bering Sea was partitioned into survey blocks, and a systematic random sample of transects within a subset of the blocks was surveyed with airborne thermal scanners using standard strip-transect methodology. Counts of walruses in photographed groups were used to model the relation between thermal signatures and the number of walruses in groups, which was used to estimate the number of walruses in groups that were detected by the scanner but not photographed. We also modeled the probability of thermally detecting various-sized walrus groups to estimate the number of walruses in groups undetected by the scanner. We used data from radio-tagged walruses to adjust on-ice estimates to account for walruses in the water during the survey. The estimated area of available habitat averaged 668,000 km2 and the area of surveyed blocks was 318,204 km2. The number of Pacific walruses within the surveyed area was estimated at 129,000 with 95% confidence limits of 55,000 to 507,000 individuals. This value can be used by managers as a minimum estimate of the total population size.

Super-Resolution Imaging of a Dielectric Microsphere Is Governed by the Waist of Its Photonic Nanojet.

PubMed

Yang, Hui; Trouillon, Raphaël; Huszka, Gergely; Gijs, Martin A M

2016-08-10

Dielectric microspheres with appropriate refractive index can image objects with super-resolution, that is, with a precision well beyond the classical diffraction limit. A microsphere is also known to generate upon illumination a photonic nanojet, which is a scattered beam of light with a high-intensity main lobe and very narrow waist. Here, we report a systematic study of the imaging of water-immersed nanostructures by barium titanate glass microspheres of different size. A numerical study of the light propagation through a microsphere points out the light focusing capability of microspheres of different size and the waist of their photonic nanojet. The former correlates to the magnification factor of the virtual images obtained from linear test nanostructures, the biggest magnification being obtained with microspheres of ∼6-7 μm in size. Analyzing the light intensity distribution of microscopy images allows determining analytically the point spread function of the optical system and thereby quantifies its resolution. We find that the super-resolution imaging of a microsphere is dependent on the waist of its photonic nanojet, the best resolution being obtained with a 6 μm Ø microsphere, which generates the nanojet with the minimum waist. This comparison allows elucidating the super-resolution imaging mechanism.

Acceleration of 500 keV Negative Ion Beams By Tuning Vacuum Insulation Distance On JT-60 Negative Ion Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kojima, A.; Hanada, M.; Tanaka, Y.

2011-09-26

Acceleration of a 500 keV beam up to 2.8 A has been achieved on a JT-60U negative ion source with a three-stage accelerator by overcoming low voltage holding which is one of the critical issues for realization of the JT-60SA ion source. In order to improve the voltage holding, preliminary voltage holding tests with small-size grids with uniform and locally intense electric fields were carried out, and suggested that the voltage holding was degraded by both the size and local electric field effects. Therefore, the local electric field was reduced by tuning gap lengths between the large size grids andmore » grid support structures of the accelerator. Moreover, a beam radiation shield which limited extension of the minimum gap length was also optimized so as to reduce the local electric field while maintaining the shielding effect. These modifications were based on the experiment results, and significantly increased the voltage holding from <150 kV/stage for the original configuration to 200 kV/stage. These techniques for improvement of voltage holding should also be applicable to other large ion sources accelerators such as those for ITER.« less

42 CFR 447.52 - Minimum and maximum income-related charges.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Family size 1 or 2 3 or 4 5 or more $150 or less $1 $1 $1 $151 or $200 2 1 1 $201 to $250 3 1 1 $251 to... family income, as required under § 447.51(d), the following rules apply: (a) Minimum charge. A charge of at least $1.00 per month is imposed on each— (1) One- or two-person family with monthly gross income...

Theoretical study of network design methodologies for the aerial relay system. [energy consumption and air traffic control

NASA Technical Reports Server (NTRS)

Rivera, J. M.; Simpson, R. W.

1980-01-01

The aerial relay system network design problem is discussed. A generalized branch and bound based algorithm is developed which can consider a variety of optimization criteria, such as minimum passenger travel time and minimum liner and feeder operating costs. The algorithm, although efficient, is basically useful for small size networks, due to its nature of exponentially increasing computation time with the number of variables.

A Review of ETS Differential Item Functioning Assessment Procedures: Flagging Rules, Minimum Sample Size Requirements, and Criterion Refinement. Research Report. ETS RR-12-08

ERIC Educational Resources Information Center

Zwick, Rebecca

2012-01-01

Differential item functioning (DIF) analysis is a key component in the evaluation of the fairness and validity of educational tests. The goal of this project was to review the status of ETS DIF analysis procedures, focusing on three aspects: (a) the nature and stringency of the statistical rules used to flag items, (b) the minimum sample size…

Sexual reproduction of the Hawaiian black coral Antipathes griggi (Cnidaria: Antipatharia)

NASA Astrophysics Data System (ADS)

Wagner, D.; Waller, R. G.; Montgomery, A. D.; Kelley, C. D.; Toonen, R. J.

2012-09-01

The Hawaiian black coral fishery has maintained steady catch levels for over 50 years. However, recent declines in the biomass of commercially valuable Hawaiian black corals question whether regulations need to be redefined for sustainable harvesting. Fishery management efforts are complicated by the limited information on the basic life history and reproduction of black corals. To address this knowledge gap, we used histological techniques to investigate sexual reproductive processes within Antipathes griggi, the dominant species targeted by the fishery. Our results indicate that A. griggi is likely gonochoric with a 1:1 sex ratio and has an annual reproductive cycle. Furthermore, the percentage of polyps containing gametes dropped continuously throughout the reproductive season, indicating that spawning occurs in successive events with greatest intensity between November and December. Current fishing regulations prohibit harvesting of colonies <90 cm in height in state waters, and colonies <120 cm in height in federal waters. This study indicates that ~80% meeting the state harvesting limit, and ~90% of colonies meeting the federal limit, are sexually mature. Therefore, increasing these minimum size harvesting limits would ensure that more colonies can reproduce before being exposed to fishing mortality. Although A. griggi can be found to depths of 100 m, it is rare below the 75 m depth limit at which commercial harvest occurs in Hawai`i. Thus, the supposed depth refuge from harvest does not really exist.

28 CFR 544.74 - Work assignment limitations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Work assignment limitations. 544.74... EDUCATION Literacy Program § 544.74 Work assignment limitations. These limitations on work assignment... order to be considered for a commissary work assignment above minimum pay level, an institution work...

A double dissociation of the acuity and crowding limits to letter identification, and the promise of improved visual screening

PubMed Central

Song, Shuang; Levi, Dennis M.; Pelli, Denis G.

2014-01-01

Here, we systematically explore the size and spacing requirements for identifying a letter among other letters. We measure acuity for flanked and unflanked letters, centrally and peripherally, in normals and amblyopes. We find that acuity, overlap masking, and crowding each demand a minimum size or spacing for readable text. Just measuring flanked and unflanked acuity is enough for our proposed model to predict the observer's threshold size and spacing for letters at any eccentricity. We also find that amblyopia in adults retains the character of the childhood condition that caused it. Amblyopia is a developmental neural deficit that can occur as a result of either strabismus or anisometropia in childhood. Peripheral viewing during childhood due to strabismus results in amblyopia that is crowding limited, like peripheral vision. Optical blur of one eye during childhood due to anisometropia without strabismus results in amblyopia that is acuity limited, like blurred vision. Furthermore, we find that the spacing:acuity ratio of flanked and unflanked acuity can distinguish strabismic amblyopia from purely anisometropic amblyopia in nearly perfect agreement with lack of stereopsis. A scatter diagram of threshold spacing versus acuity, one point per patient, for several diagnostic groups, reveals the diagnostic power of flanked acuity testing. These results and two demonstrations indicate that the sensitivity of visual screening tests can be improved by using flankers that are more tightly spaced and letter like. Finally, in concert with Strappini, Pelli, Di Pace, and Martelli (submitted), we jointly report a double dissociation between acuity and crowding. Two clinical conditions—anisometropic amblyopia and apperceptive agnosia—each selectively impair either acuity A or the spacing:acuity ratio S/A, not both. Furthermore, when we specifically estimate crowding, we find a double dissociation between acuity and crowding. Models of human object recognition will need to accommodate this newly discovered independence of acuity and crowding. PMID:24799622

Control of minimum member size in parameter-free structural shape optimization by a medial axis approximation

NASA Astrophysics Data System (ADS)

Schmitt, Oliver; Steinmann, Paul

2018-06-01

We introduce a manufacturing constraint for controlling the minimum member size in structural shape optimization problems, which is for example of interest for components fabricated in a molding process. In a parameter-free approach, whereby the coordinates of the FE boundary nodes are used as design variables, the challenging task is to find a generally valid definition for the thickness of non-parametric geometries in terms of their boundary nodes. Therefore we use the medial axis, which is the union of all points with at least two closest points on the boundary of the domain. Since the effort for the exact computation of the medial axis of geometries given by their FE discretization highly increases with the number of surface elements we use the distance function instead to approximate the medial axis by a cloud of points. The approximation is demonstrated on three 2D examples. Moreover, the formulation of a minimum thickness constraint is applied to a sensitivity-based shape optimization problem of one 2D and one 3D model.

Structural changes in the hot Algol OGLE-LMC-DPV-097 and its disc related to its long cycle

NASA Astrophysics Data System (ADS)

Garcés L, J.; Mennickent, R. E.; Djurašević, G.; Poleski, R.; Soszyński, I.

2018-06-01

Double Periodic Variables (DPVs) are hot Algols showing a long photometric cycle of uncertain origin. We report the discovery of changes in the orbital light curve of OGLE-LMC-DPV-097 which depend on the phase of its long photometric cycle. During the ascending branch of the long cycle the brightness at the first quadrature is larger than during the second quadrature, during the maximum of the long cycle the brightness is basically the same at both quadratures, during the descending branch the brightness at the second quadrature is larger than during the first quadrature, and during the minimum of the long cycle the secondary minimum disappears. We model the light curve at different phases of the long cycle and find that the data are consistent with changes in the properties of the accretion disc and two disc spots. The disc's size and temperature change with the long-cycle period. We find a smaller and hotter disc at minimum, and larger and cooler disc at maximum. The spot temperatures, locations, and angular sizes also show variability during the long cycle.

Control of minimum member size in parameter-free structural shape optimization by a medial axis approximation

NASA Astrophysics Data System (ADS)

Schmitt, Oliver; Steinmann, Paul

2017-09-01

We introduce a manufacturing constraint for controlling the minimum member size in structural shape optimization problems, which is for example of interest for components fabricated in a molding process. In a parameter-free approach, whereby the coordinates of the FE boundary nodes are used as design variables, the challenging task is to find a generally valid definition for the thickness of non-parametric geometries in terms of their boundary nodes. Therefore we use the medial axis, which is the union of all points with at least two closest points on the boundary of the domain. Since the effort for the exact computation of the medial axis of geometries given by their FE discretization highly increases with the number of surface elements we use the distance function instead to approximate the medial axis by a cloud of points. The approximation is demonstrated on three 2D examples. Moreover, the formulation of a minimum thickness constraint is applied to a sensitivity-based shape optimization problem of one 2D and one 3D model.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morales, F. Y.; Bryden, G.; Werner, M. W.

We present dual-band Herschel /PACS imaging for 59 main-sequence stars with known warm dust ( T {sub warm} ∼ 200 K), characterized by Spitzer . Of 57 debris disks detected at Herschel wavelengths (70 and/or 100 and 160 μ m), about half have spectral energy distributions (SEDs) that suggest two-ring disk architectures mirroring that of the asteroid–Kuiper Belt geometry; the rest are consistent with single belts of warm, asteroidal material. Herschel observations spatially resolve the outer/cold dust component around 14 A-type and 4 solar-type stars with two-belt systems, 15 of which for the first time. Resolved disks are typically observedmore » with radii >100 AU, larger than expected from a simple blackbody fit. Despite the absence of narrow spectral features for ice, we find that the shape of the continuum, combined with resolved outer/cold dust locations, can help constrain the grain size distribution and hint at the dust’s composition for each resolved system. Based on the combined Spitzer /IRS+Multiband Imaging Photometer (5-to-70 μ m) and Herschel /PACS (70-to-160 μ m) data set, and under the assumption of idealized spherical grains, we find that over half of resolved outer/cold belts are best fit with a mixed ice/rock composition. Minimum grain sizes are most often equal to the expected radiative blowout limit, regardless of composition. Three of four resolved systems around the solar-type stars, however, tend to have larger minimum grains compared to expectation from blowout ( f {sub MB} = a {sub min}/ a {sub BOS} ∼ 5). We also probe the disk architecture of 39 Herschel -unresolved systems by modeling their SEDs uniformly, and find them to be consistent with 31 single- and 8 two-belt debris systems.« less

Using Structural Equation Modeling to Assess Functional Connectivity in the Brain: Power and Sample Size Considerations

ERIC Educational Resources Information Center

Sideridis, Georgios; Simos, Panagiotis; Papanicolaou, Andrew; Fletcher, Jack

2014-01-01

The present study assessed the impact of sample size on the power and fit of structural equation modeling applied to functional brain connectivity hypotheses. The data consisted of time-constrained minimum norm estimates of regional brain activity during performance of a reading task obtained with magnetoencephalography. Power analysis was first…

77 FR 38229 - Rules Prohibiting the Aggregation of Orders To Satisfy Minimum Block Sizes or Cap Size...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-27

..., investment advisers and foreign persons (as described in this release), to transact block trades for customers who are not ECPs, if such CTA, investment adviser or foreign person has more than $25,000,000 in... eligible contract participants (``non-ECPS''), if such CTA, investment adviser or foreign person has more...

Small-Sample DIF Estimation Using SIBTEST, Cochran's Z, and Log-Linear Smoothing

ERIC Educational Resources Information Center

Lei, Pui-Wa; Li, Hongli

2013-01-01

Minimum sample sizes of about 200 to 250 per group are often recommended for differential item functioning (DIF) analyses. However, there are times when sample sizes for one or both groups of interest are smaller than 200 due to practical constraints. This study attempts to examine the performance of Simultaneous Item Bias Test (SIBTEST),…

Reading Materials in Large Type. Reference Circular No. 87-4.

ERIC Educational Resources Information Center

Library of Congress, Washington, DC. National Library Service for the Blind and Physically Handicapped.

This circular provides information about reading materials in large type, i.e., materials set in type that is a minimum size of 14-point and, most commonly, 16- to 18-point size. Most of the materials listed are typeset, but a few are photographically enlarged conventionally printed books or typewritten materials prepared using a large-print…

38 CFR 36.4361 - Acceptable ownership arrangements and documentation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... condominium, including building types, architectural style and the size of the units for those phases of the..., building types, architectural style and size of the units, etc. of these phases. However, the minimum... elements. (See § 36.4864(a)(6).) (Authority: 38 U.S.C. 3703(c)(1), 3710(a)(6)) (The Office of Management...