¡VAMOS! (Viable Alternative Mine Operating System) - a 'Horizon 2020' project

NASA Astrophysics Data System (ADS)

Sword, Cameron; Bodo, Balazs; Kapusniak, Stef; Bosman, Frank; Rainbird, Jenny; Silva, Eduardo

2017-04-01

The 42-month ¡VAMOS! project (Viable Alternative Mine Operating System, Grant Agreement 642477, www.vamos-project.eu), funded by the EC H2020 Programme, will enable access to high-grade EU reserves of mineral ore-bodies by developing an innovative clean and low visibility mining technique. The project will demonstrate the technological and economic viability of the underwater extraction of metallic mineral deposits which are currently technologically, economically, and environmentally unobtainable. In doing so, ¡VAMOS! hopes to encourage investment in abandoned open-pit mines and prospective mines, helping to put the EU back on a level playing field with the rest of the world in terms of access to strategically important minerals. The ¡VAMOS! concept is defined by a remotely-operated underwater mining vehicle, adapted and improved from existing subsea mining technology. Operating in tandem with an HROV, the mining vehicle will connect to a flexible riser through which slurried mined material will be pumped from the mudline to onshore dewatering facilities via a floating mobile deployment-module, on which will be fitted a bypass system linked to an LIBS, allowing real-time grade-control. Analysis of European and national regulation and stakeholder assessments found there is significant support for developing the technology among local communities and governments. An initial environmental assessment of the potential impact of the innovative mining operation concluded the project has a smaller environmental footprint than conventional mining operations: this is due to factors including the quieter operation and absence of blasting, zero water-table flux, and the higher stripping ratio enabled by higher fluid pressure acting on the sidewalls of the mine. The prototypes are currently in their construction phase following a final design freeze in October 2016. Work is now underway on the foresight visioning, economic evaluation and policy guidelines for the ¡VAMOS! methodology and technologies; the project team will be identifying key areas of research interest and assessing the micro and macroeconomic impact of ¡VAMOS!. The deadline for the completion of the underwater mining vehicle prototype is May 2017, and the HROV hardware and software is to be completed by July 2017. Site-tests will take place in the months after the build completion at a number of unique abandoned mines across Europe, with final proof of operational viability due by November 2017.

Identification of ex-sand mining area using optical and SAR imagery

NASA Astrophysics Data System (ADS)

Indriasari, Novie; Kusratmoko, Eko; Indra, Tito Latif; Julzarika, Atriyon

2018-05-01

Open mining activities in Sumedang Regency has been operated since 1984 impacted to degradation of environment due to large area of ex-mining. Therefore, identification of ex-mining area which generally been used for sand mining is crucial and important to detect and monitor recent environmental degradation impacted from the ex-mining activities. In this research, identification ex-sand mining area using optical and SAR data in Sumedang Regency will be discussed. We use Landsat 5 TM acquisition date August 01, 2009 and Landsat 8 OLI acquired on June 24, 2016 to identify location of sand mining area, processed using Tasselled Cap Trasformation (TCT), while the landform deformation approached using ALOS PALSAR in 2009 and ALOS PALSAR 2 in 2016 processed using SAR interferometry (InSAR) method. The results show that TCT and InSAR method can can be used to identify the areas of ex-sand mining clearly. In 2016 the total area of ex-mining were 352.92 Ha. The land deformation show that during 7 years period since 2009 has impacted to the deformation at 7 meters.

Model of environmental life cycle assessment for coal mining operations.

PubMed

Burchart-Korol, Dorota; Fugiel, Agata; Czaplicka-Kolarz, Krystyna; Turek, Marian

2016-08-15

This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. Copyright © 2016 Elsevier B.V. All rights reserved.

Exploring the use of situation awareness in behaviors and practices of health and safety leaders.

PubMed

Willmer, D R

2017-01-01

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders' efforts to build and maintain a mining operation's workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders' perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Managing equipment innovations in mining: A review.

PubMed

Trudel, Bryan; Nadeau, Sylvie; Zaras, Kazimierz; Deschamps, Isabelle

2015-01-01

Technological innovations in mining equipment have led to increased productivity and occupational health and safety (OHS) performance, but their introduction also brings new risks for workers. The aim of this study is to provide support for mining industry managers who are required to reconcile equipment choices with OHS and productivity. Examination of the literature through interdisciplinary digital databases. Databases were searched using specific combinations of keywords and limited to studies dating back no farther than 1992. The ``snowball'' technique was also used to examining the references listed in research articles initially identified with the databases. A total of 19 contextual factors were identified as having the potential to influence the OHS and productivity leverage of equipment innovations. The most often cited among these factors are the level of training provided to the equipment operators, operator experience and age, supervisor leadership abilities, and maintaining good relations within work crews. Interactions between these factors are not discussed in mining innovation literature. It would be helpful to use a systems thinking approach which incorporates interaction between relevant actors and factors to define properly the most sensitive aspects of innovation management as it applies to mining equipment.

Biota dose assessment of small mammals sampled near uranium mines in northern Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jannik, T.; Minter, K.; Kuhne, W.

In 2015, the U. S. Geological Survey (USGS) collected approximately 50 small mammal carcasses from Northern Arizona uranium mines and other background locations. Based on the highest gross alpha results, 11 small mammal samples were selected for radioisotopic analyses. None of the background samples had significant gross alpha results. The 11 small mammals were identified relative to the three ‘indicator’ mines located south of Fredonia, AZ on the Kanab Plateau (Kanab North Mine, Pinenut Mine, and Arizona 1 Mine) (Figure 1-1) and are operated by Energy Fuels Resources Inc. (EFRI). EFRI annually reports soil analysis for uranium and radium-226 usingmore » Arizona Department of Environmental Quality (ADEQ)-approved Standard Operating Procedures for Soil Sampling (EFRI 2016a, 2016b, 2017). In combination with the USGS small mammal radioiosotopic tissue analyses, a biota dose assessment was completed by Savannah River National Laboratory (SRNL) using the RESidual RADioactivity-BIOTA (RESRAD-BIOTA, V. 1.8) dose assessment tool provided by the Argonne National Laboratory (ANL 2017).« less

Method to Select Technical Terms for Glossaries in Support of Joint Task Force Operations

DTIC Science & Technology

2012-01-01

have been prohibitively time-consuming. Instead, we identified two publicly available terminology extractor tools: TerMine (NaCTEM, 2011) and Alchemy ...and that from the latter, by high recall. The Alchemy approach contrasts with that used in TerMine in that Alchemy will process the text with...information categories, such as person, location, and organization, in addition to returning topic keywords. Output from both TerMine and Alchemy

Measuring mining safety with injury statistics: lost workdays as indicators of risk.

PubMed

Coleman, Patrick J; Kerkering, John C

2007-01-01

Mining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injury rates over the last century. Coal mine fatality rates, for example, have dropped almost a thousand-fold since their peak in 1908. While incidence rates are very important indicators, lost worktime measures offer an alternative metric for evaluating job safety and health performance. The first objective of this study examined the distributions and summary statistics of all injuries reported to the Mine Safety and Health Administration from 1983 through 2004. Over the period studied (1983-2004), there were 31,515,368 lost workdays associated with mining injuries, for an equivalent of 5,700 person-years lost annually. The second objective addressed the problem of comparing safety program performance in mines for situations where denominator data were lacking. By examining the consequences of injuries, comparisons can be made between disparate operations without the need for denominators. Total risk in the form of lost workday sums can help to distinguish between lower- and higher-risk operations or time periods. Our method was to use a beta distribution to model the losses and to compare underground coal mining to underground metal/nonmetal mining from 2000 to 2004. Our results showed the probability of an injury having 10 or more lost workdays was 0.52 for coal mine cases versus 0.35 for metal/nonmetal mine cases. In addition, a comparison of injuries involving continuous mining machines over 2001-2002 versus 2003-2004 showed that the ratio of average losses in the later period to those in the earlier period was approximately 1.08, suggesting increasing risks for such operations. This denominator-free safety measure will help the mining industry more effectively identify higher-risk operations and more realistically evaluate their safety improvement programs. Attention to a variety of metrics concerning the performance of a job safety and health program will enhance industry's ability to manage these programs and reduce risk.

Application of EREP imagery to fracture-related mine safety hazards and environmental problems in mining

NASA Technical Reports Server (NTRS)

Wier, C. E.; Wobber, F. J.; Amato, R. V.; Russell, O. R. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Numerous fracture traces were detected on both the color transparencies and black and white spectral bands. Fracture traces of value to mining hazards analysis were noted on the EREP imagery which could not be detected on either the ERTS-1 or high altitude aircraft color infrared photography. Several areas of mine subsidence occurring in the Busseron Creek area near Sullivan, Indiana were successfully identified using color photography. Skylab photography affords an increase over comparable scale ERTS-1 imagery in level of information obtained in mined lands inventory and reclamation analysis. A review of EREP color photography permitted the identification of a substantial number of non-fuel mines within the Southern Indiana test area. A new mine was detected on the EREP photography without prior data. EREP has definite value for estimating areal changes in active mines and for detecting new non-fuel mines. Gob piles and slurry ponds of several acres could be detected on the S-190B color photography when observed in association with large scale mining operations. Apparent degradation of water quality resulting from acid mine drainage and/or siltation was noted in several ponds or small lakes and appear to be related to intensive mining activity near Sullivan, Indiana.

Finding a Needle in the Haystack: Identification of Functionally Important Minority Phases in an Operating Battery.

PubMed

Zhang, Kai; Ren, Fang; Wang, Xuelong; Hu, Enyuan; Xu, Yahong; Yang, Xiao-Qing; Li, Hong; Chen, Liquan; Pianetta, Piero; Mehta, Apurva; Yu, Xiqian; Liu, Yijin

2017-12-13

The in-depth understanding of the minority phases' roles in functional materials, e.g., batteries, is critical for optimizing the system performance and the operational efficiency. Although the visualization of battery electrode under operating conditions has been demonstrated, the development of advanced data-mining approaches is still needed in order to identify minority phases and to understand their functionalities. The present study uses nanoscale X-ray spectromicroscopy to study a functional LiCoO 2 /Li battery pouch cell. The data-mining approaches developed herein were used to search through over 10 million X-ray absorption spectra that cover more than 100 active cathode particles. Two particles with unanticipated chemical fingerprints were identified and further analyzed, providing direct evidence and valuable insight into the undesired side reactions involving the cation dissolution and precipitation as well as the local overlithiation-caused subparticle domain deactivation. The data-mining approach described in this work is widely applicable to many other structurally complex and chemically heterogeneous systems, in which the secondary/minority phases could critically affect the overall performance of the system, well beyond battery research.

A study of acid and ferruginous mine water in coal mining operations

NASA Astrophysics Data System (ADS)

Atkins, A. S.; Singh, R. N.

1982-06-01

The paper describes a bio-chemical investigation in the laboratory to identify various factors which promote the formation of acidic and ferruginous mine water. Biochemical reactions responsible for bacterial oxidation of Iron pyrites are described. The acidic and ferruginous mine water are not only responsible for the corrosion of mine plant and equipment and formation of scales in the delivery pipe range, but also pollution of the mine surface environment, thus affecting the surface ecology. Control measures to mitigate the adverse effects of acid mine discharge include the protection of mining equipment and prevention of formation of acid and ferruginous water. Various control measures discussed in the paper are blending with alkaline or spring water, use of neutralising agents and bactericides, and various types of seals for preventing water and air coming into contact with pyrites in caved mine workings.

Challenges with minimising mercury pollution in the small-scale gold mining sector: experiences from the Guianas.

PubMed

Hilson, Gavin; Vieira, Rickford

2007-12-01

This paper examines the barriers to mitigating mercury pollution at small-scale gold mines in the Guianas (Guyana, French Guiana and Suriname), and prescribes recommendations for overcoming these obstacles. Whilst considerable attention has been paid to analysing the environmental impacts of operations in the region, minimal research has been undertaken to identify appropriate policy and educational initiatives for addressing the mounting mercury problem. Findings from recent fieldwork and selected interviews with operators from Guyanese and Surinamese gold mining regions reveal that legislative incapacity, the region's varied industry policy stances, various technological problems, and low environmental awareness on the part of communities are impeding efforts to facilitate improved mercury management at small-scale gold mines in the Guianas. Marked improvements can be achieved, however, if legislation, particularly that pertaining to mercury, is harmonised in the region; educational seminars continue to be held in important mining districts; and additional outlets for disseminating environmental equipment and mercury-free technologies are provided.

Forecasting the ocean optical environment in support of Navy mine warfare operations

NASA Astrophysics Data System (ADS)

Ladner, S. D.; Arnone, R.; Jolliff, J.; Casey, B.; Matulewski, K.

2012-06-01

A 3D ocean optical forecast system called TODS (Tactical Ocean Data System) has been developed to determine the performance of underwater LIDAR detection/identification systems. TODS fuses optical measurements from gliders, surface satellite optical properties, and 3D ocean forecast circulation models to extend the 2-dimensional surface satellite optics into a 3-dimensional optical volume including subsurface optical layers of beam attenuation coefficient (c) and diver visibility. Optical 3D nowcast and forecasts are combined with electro-optical identification (EOID) models to determine the underwater LIDAR imaging performance field used to identify subsurface mine threats in rapidly changing coastal regions. TODS was validated during a recent mine warfare exercise with Helicopter Mine Countermeasures Squadron (HM-14). Results include the uncertainties in the optical forecast and lidar performance and sensor tow height predictions that are based on visual detection and identification metrics using actual mine target images from the EOID system. TODS is a new capability of coupling the 3D optical environment and EOID system performance and is proving important for the MIW community as both a tactical decision aid and for use in operational planning, improving timeliness and efficiency in clearance operations.

Mars methane analogue mission: Mission simulation and rover operations at Jeffrey Mine and Norbestos Mine Quebec, Canada

NASA Astrophysics Data System (ADS)

Qadi, A.; Cloutis, E.; Samson, C.; Whyte, L.; Ellery, A.; Bell, J. F.; Berard, G.; Boivin, A.; Haddad, E.; Lavoie, J.; Jamroz, W.; Kruzelecky, R.; Mack, A.; Mann, P.; Olsen, K.; Perrot, M.; Popa, D.; Rhind, T.; Sharma, R.; Stromberg, J.; Strong, K.; Tremblay, A.; Wilhelm, R.; Wing, B.; Wong, B.

2015-05-01

The Canadian Space Agency (CSA), through its Analogue Missions program, supported a microrover-based analogue mission designed to simulate a Mars rover mission geared toward identifying and characterizing methane emissions on Mars. The analogue mission included two, progressively more complex, deployments in open-pit asbestos mines where methane can be generated from the weathering of olivine into serpentine: the Jeffrey mine deployment (June 2011) and the Norbestos mine deployment (June 2012). At the Jeffrey Mine, testing was conducted over 4 days using a modified off-the-shelf Pioneer rover and scientific instruments including Raman spectrometer, Picarro methane detector, hyperspectral point spectrometer and electromagnetic induction sounder for testing rock and gas samples. At the Norbestos Mine, we used the research Kapvik microrover which features enhanced autonomous navigation capabilities and a wider array of scientific instruments. This paper describes the rover operations in terms of planning, deployment, communication and equipment setup, rover path parameters and instrument performance. Overall, the deployments suggest that a search strategy of “follow the methane” is not practical given the mechanisms of methane dispersion. Rather, identification of features related to methane sources based on image tone/color and texture from panoramic imagery is more profitable.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This study compared conditions, practices, and attitudes at underground bituminous coal mines having low injury incidence rates with those found at mines having high injury incidence rates. Several characteristics common to many of the low incidence rate mines that differentiate them from those having high incidence rates were identified. (1) Training programs: adequate and relevant training materials; qualified instructors; restricted classroom size to encourage student participation; and tailored to meet individual miner needs. (2) Management/labor relations tend to have a positive impact upon a mine's accident and injury experience when: both management and labor have a positive attitude toward safetymore » and health; open lines of communication permit management and labor to jointly reconcile problems affecting safety and health; representatives of labor become actively involved in issues concerning safety, health and production; and management and labor identify and accept their joint responsibility for correcting unsafe conditions and practices. (3) Safety and health conditions are improved when: standard operating procedures are established, understood, and implemented; management equitably enforces established policies concerning absenteeism, job assignments, and standard operating procedures; formal safety and health programs are communicated to all employees and subsequently implemented by management and labor; safety department has top management support in terms of funds, manpower, and the authority necessary to implement the safety and health program; mine plans are thoroughly reviewed by management, labor, and MSHA to insure that such plans incorporate measures to adequately control the physical environment of a coal mine; and MSHA inspection activity is most effective when the inspectors encourage increased cooperative interaction between themselves, mine management, and labor.« less

Heavy equipment maintenance wastes and environmental management in the mining industry.

PubMed

Guerin, Turlough F

2002-10-01

Maintenance wastes, if not managed properly, represent significant environmental issues for mining operations. Petroleum hydrocarbon liquid wastes were studied at an Australian site and a review of the literature and technology vendors was carried out to identify oil/water separation technologies. Treatment technologies and practices for managing oily wastewater, used across the broader mining industry in the Asia-Pacific region, were also identified. Key findings from the study were: (1) primary treatment is required to remove grease oil contamination and to protect secondary oily wastewater treatment systems from being overloaded; (2) selection of an effective secondary treatment system is dependent on influent oil droplet size and concentration, suspended solids concentration, flow rates (and their variability), environmental conditions, maintenance schedules and effectiveness, treatment targets and costs; and (3) oily wastewater treatment systems, based on mechanical separation, are favoured over those that are chemically based, as they simplify operational requirements. Source reduction, through housekeeping, equipment and reagent modifications, and segregation and/or consolidation of hydrocarbon waste streams, minimizes treatment costs, safety and environmental impact.

Study of application of ERTS-A imagery to fracture-related mine safety hazards in the coal mining industry

NASA Technical Reports Server (NTRS)

Wier, C. E.; Wobber, F. J. (Principal Investigator); Russell, O. R.; Amato, R. V.; Leshendok, T.

1973-01-01

The author has identified the following significant results. The Kings Station Mine in Gibson County, Indiana has experienced considerable roof fall problems. Detailed fracture mapping of the mine area was done with ERTS-1 and aircraft imagery, and a prediction map of roof problem areas was produced in advance of a visit. The visit to the mine and discussions with the operator indicated that of four zones mapped as potential problem areas, three coincided with areas of excessive roof fall. This positive correlation of 75% lends confidence to the validity of the technique being applied in the investigation. The mine officials expressed an interest in the project and are anxious to see the final product maps which are forthcoming.

Factors influencing mine rescue team behaviors.

PubMed

Jansky, Jacqueline H; Kowalski-Trakofler, K M; Brnich, M J; Vaught, C

2016-01-01

A focus group study of the first moments in an underground mine emergency response was conducted by the National Institute for Occupational Safety and Health (NIOSH), Office for Mine Safety and Health Research. Participants in the study included mine rescue team members, team trainers, mine officials, state mining personnel, and individual mine managers. A subset of the data consists of responses from participants with mine rescue backgrounds. These responses were noticeably different from those given by on-site emergency personnel who were at the mine and involved with decisions made during the first moments of an event. As a result, mine rescue team behavior data were separated in the analysis and are reported in this article. By considering the responses from mine rescue team members and trainers, it was possible to sort the data and identify seven key areas of importance to them. On the basis of the responses from the focus group participants with a mine rescue background, the authors concluded that accurate and complete information and a unity of purpose among all command center personnel are two of the key conditions needed for an effective mine rescue operation.

Electrical injuries in the US mining industry, 2000-2009

PubMed Central

Homce, G.T.; Cawley, J.C.

2015-01-01

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment. PMID:26346041

Electrical injuries in the US mining industry, 2000-2009.

PubMed

Homce, G T; Cawley, J C

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment.

Finding a Needle in the Haystack: Identification of Functionally Important Minority Phases in an Operating Battery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Kai; Ren, Fang; Wang, Xuelong

The in-depth understanding of the minority phases’ roles in functional materials, e.g., batteries, is critical for optimizing the system performance and the operational efficiency. Although the visualization of battery electrode under operating conditions has been demonstrated, the development of advanced data-mining approaches is still needed in order to identify minority phases and to understand their functionalities. The present study uses nanoscale X-ray spectromicroscopy to study a functional LiCoO 2/Li battery pouch cell. The data-mining approaches developed herein were used to search through over 10 million X-ray absorption spectra that cover more than 100 active cathode particles. Two particles with unanticipatedmore » chemical fingerprints were identified and further analyzed, providing direct evidence and valuable insight into the undesired side reactions involving the cation dissolution and precipitation as well as the local overlithiation-caused subparticle domain deactivation. As a result, the data-mining approach described in this work is widely applicable to many other structurally complex and chemically heterogeneous systems, in which the secondary/minority phases could critically affect the overall performance of the system, well beyond battery research.« less

Finding a Needle in the Haystack: Identification of Functionally Important Minority Phases in an Operating Battery

DOE PAGES

Zhang, Kai; Ren, Fang; Wang, Xuelong; ...

2017-11-08

The in-depth understanding of the minority phases’ roles in functional materials, e.g., batteries, is critical for optimizing the system performance and the operational efficiency. Although the visualization of battery electrode under operating conditions has been demonstrated, the development of advanced data-mining approaches is still needed in order to identify minority phases and to understand their functionalities. The present study uses nanoscale X-ray spectromicroscopy to study a functional LiCoO 2/Li battery pouch cell. The data-mining approaches developed herein were used to search through over 10 million X-ray absorption spectra that cover more than 100 active cathode particles. Two particles with unanticipatedmore » chemical fingerprints were identified and further analyzed, providing direct evidence and valuable insight into the undesired side reactions involving the cation dissolution and precipitation as well as the local overlithiation-caused subparticle domain deactivation. As a result, the data-mining approach described in this work is widely applicable to many other structurally complex and chemically heterogeneous systems, in which the secondary/minority phases could critically affect the overall performance of the system, well beyond battery research.« less

Mining Communities from a Resilience Perspective: Managing Disturbance and Vulnerability in Itabira, Brazil

NASA Astrophysics Data System (ADS)

Wasylycia-Leis, Joseph; Fitzpatrick, Patricia; Fonseca, Alberto

2014-03-01

This paper applies the resilience lens to a social-ecological system characterized by the presence of large-scale mineral extraction operations. The system in question is the Brazilian community of Itabira, Minas Gerais, host to an iron ore operation of Vale, the world's second largest mining corporation. Utilizing a resilience assessment framework, this study describes the various components of the Itabira social-ecological system revealing the challenges brought about by mining's dominance. Data collection included literature reviews and semi-structured interviews with 29 individuals representing different stakeholder groups. Findings revealed that, despite recent efforts by government to regulate the industry, the mine continues to generate press and pulse disturbances that impact the resilience of the community. Operating from the standpoint that resilience depends largely upon the management capacity of stakeholders, the research identifies three ways to improve mining governance in Itabira. First, there is a need for local government to have more power in dealings with the corporation. Concurrent with this power, however, the municipality must demonstrate ownership over its fate, ideally through the creation of a sustainability plan. Finally, all key parties must demonstrate commitment to cooperating to resolve outstanding disturbances, even when these fall outside the regulatory approval process. While Itabira will remain a mining town for the foreseeable future, actions taken now to address challenges will only strengthen community well-being and sustainability moving forward.

Aquatic Ecosystem Enhancement at Mountaintop Mining Sites Symposium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Black, D. Courtney; Lawson, Peter; Morgan, John

2000-01-12

Welcome to this symposium which is part of the ongoing effort to prepare an Environmental Impact Statement (EIS) regarding mountaintop mining and valley fills. The EIS is being prepared by the U.S. Environmental Protection Agency, U.S. Army Corps of Engineers, U.S. Office of Surface Mining, and U.S. Fish and Wildlife Service, in cooperation with the State of West Virginia. Aquatic Ecosystem Enhancement (AEE) at mountaintop mining sites is one of fourteen technical areas identified for study by the EIS Interagency Steering Committee. Three goals were identified in the AEE Work Plan: 1. Assess mining and reclamation practices to show howmore » mining operations might be carried out in a way that minimizes adverse impacts to streams and other environmental resources and to local communities. Clarify economic and technical constraints and benefits. 2. Help citizens clarify choices by showing whether there are affordable ways to enhance existing mining, reclamation, mitigation processes and/or procedures. 3. Ide identify data needed to improve environmental evaluation and design of mining projects to protect the environment. Today’s symposium was proposed in the AEE Team Work Plans but coordinated planning for the event began September 15, 1999 when representatives from coal industry, environmental groups and government regulators met in Morgantown. The meeting participants worked with a facilitator from the Canaan Valley Institute to outline plans for the symposium. Several teams were formed to carry out the plans we outlined in the meeting.« less

30 CFR 921.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... surface coal mining operations. 921.764 Section 921.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS... mining operations. Part 764 of this chapter, State Processes for Designating Areas Unsuitable for Surface...

30 CFR 933.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... surface coal mining operations. 933.764 Section 933.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS... mining operations. Part 764 of this chapter, State Processes for Designatng Areas Unsuitable for Surface...

Use of Lead Isotopes to Identify Sources of Metal and Metalloid Contaminants in Atmospheric Aerosol from Mining Operations

PubMed Central

Félix, Omar I.; Csavina, Janae; Field, Jason; Rine, Kyle P.; Sáez, A. Eduardo; Betterton, Eric A.

2014-01-01

Mining operations are a potential source of metal and metalloid contamination by atmospheric particulate generated from smelting activities, as well as from erosion of mine tailings. In this work, we show how lead isotopes can be used for source apportionment of metal and metalloid contaminants from the site of an active copper mine. Analysis of atmospheric aerosol shows two distinct isotopic signatures: one prevalent in fine particles (< 1 μm aerodynamic diameter) while the other corresponds to coarse particles as well as particles in all size ranges from a nearby urban environment. The lead isotopic ratios found in the fine particles are equal to those of the mine that provides the ore to the smelter. Topsoil samples at the mining site show concentrations of Pb and As decreasing with distance from the smelter. Isotopic ratios for the sample closest to the smelter (650 m) and from topsoil at all sample locations, extending to more than 1 km from the smelter, were similar to those found in fine particles in atmospheric dust. The results validate the use of lead isotope signatures for source apportionment of metal and metalloid contaminants transported by atmospheric particulate. PMID:25496740

Reduction of Conflicts in Mining Development Using "Good Neighbor Agreements"

NASA Astrophysics Data System (ADS)

Masaitis, A.

2013-05-01

New environmental and social challenges for the mining industry in both developed and developing countries show the obvious need to implement "responsible" mining practices that include improved community involvement. Good Neighbor Agreements (GNA's) are a relatively new mechanism for improving communication and trust between a mining company and the community. The focus of a GNA will be to provide a written and enforceable agreement, negotiated between the concerned public and the respective mining company to respond to concerns from the public, and also provide a mechanism for conflict resolution, when there is mutual benefit to maintain a working relationship. Development of GNA's, a recently evolving process that promotes environmentally sound relationships between mines and the surrounding communities. Modify and apply the resulting GNA formulas to the developing countries and countries with transitional economies. This is particularly important for countries that have poorly functioning regulatory systems that cannot guarantee a healthy and safe environment for the communities. The fundamental questions addressed by this research. 1. This is a three-year research project started in August 2012 at the University of Nevada, Reno (UNR) to develop a Good Neighbor Agreements standards as well as to investigate the details of mine development. 2. Identify spheres of possible cooperation between mining companies, government organizations, and the Non-Governmental Organizations (NGO's). Use this cooperation to develop international standards for the GNA, to promote exchange of environmental information, and exchange of successful environmental, health, and safety practices between mining operations from different countries. Discussion: The Good Neighbor Agreement currently evolving will address the following: 1. Provide an economically viable mechanism for developing a partnership between mining operations and the local communities that will increase mining industry's accountability and provide higher levels of confidence for the community that a mine is operated in a safe and sustainable manner. 2. Increase the diversity of people benefiting from the results of this research by providing standards that could be adopted in developing countries. The goal of the GNA is to have open access for the public to the safety, health, and environmental information pertaining to the mining operation, as well as to educate the local communities about safe and sustainable mining practices that promote mutual acknowledgment of the need to build a relationship amenable to each other's needs. Frequent conflicts between mining companies and surrounding communities lead to work disruptions or even mine closures and show the necessity of a less confrontational approach to environmental and social justice. Because of the higher quality environmental standards already in place, this new approach perhaps should first be established in developed countries and then applied to other countries with less developed economies. The Good Neighbor Agreement is a unique way to provide the benefits for the both mining operations and local community to provide a mechanism for development of trust and communication that offer the potential to protect both mining and community interests, and can possibly reduce conflicts in resource development projects.

30 CFR 762.15 - Exploration on land designated as unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of surface coal mining operations pursuant to section 522 of the Act and regulations of this... for surface coal mining operations. 762.15 Section 762.15 Mineral Resources OFFICE OF SURFACE MINING... AREAS AS UNSUITABLE FOR SURFACE COAL MINING OPERATIONS § 762.15 Exploration on land designated as...

30 CFR 762.15 - Exploration on land designated as unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of surface coal mining operations pursuant to section 522 of the Act and regulations of this... for surface coal mining operations. 762.15 Section 762.15 Mineral Resources OFFICE OF SURFACE MINING... AREAS AS UNSUITABLE FOR SURFACE COAL MINING OPERATIONS § 762.15 Exploration on land designated as...

30 CFR 762.15 - Exploration on land designated as unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of surface coal mining operations pursuant to section 522 of the Act and regulations of this... for surface coal mining operations. 762.15 Section 762.15 Mineral Resources OFFICE OF SURFACE MINING... AREAS AS UNSUITABLE FOR SURFACE COAL MINING OPERATIONS § 762.15 Exploration on land designated as...

30 CFR 762.15 - Exploration on land designated as unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of surface coal mining operations pursuant to section 522 of the Act and regulations of this... for surface coal mining operations. 762.15 Section 762.15 Mineral Resources OFFICE OF SURFACE MINING... AREAS AS UNSUITABLE FOR SURFACE COAL MINING OPERATIONS § 762.15 Exploration on land designated as...

30 CFR 762.15 - Exploration on land designated as unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of surface coal mining operations pursuant to section 522 of the Act and regulations of this... for surface coal mining operations. 762.15 Section 762.15 Mineral Resources OFFICE OF SURFACE MINING... AREAS AS UNSUITABLE FOR SURFACE COAL MINING OPERATIONS § 762.15 Exploration on land designated as...

30 CFR 75.311 - Main mine fan operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main mine fan operation. 75.311 Section 75.311... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.311 Main mine fan operation. (a) Main mine fans shall be continuously operated, except as otherwise approved in the ventilation plan, or when...

Principles of adoption of the successful environmental practices used in developed countries into mining industry in developing countries.

NASA Astrophysics Data System (ADS)

Masaitis, Alexandra

2013-04-01

The successful implementation of the environmental practices in the mining industry is of a paramount importance, as it not only prevents both local and trans-border pollution but also guarantees clean and healthy environment for the people regardless of their place of habitation. It is especially important to encourage the progress of the environmental practices implementation in developing countries because such countries have resource-oriented economy based on exploitation of nonrenewable resources. Poor environmental practices in developing countries will lead to local environmental crises that could eventually spill into surrounding countries including the most economically advanced. This abstract is a summary of a two-year research project attempted (1) to determine deficiencies of the mining sector ecological practices in developing countries and (2) to suggest substitute practices from developed countries that could be adapted to the developing countries reality. The following research methods were used: 1. The method of the system analysis, where the system is an interaction of the sets of environmental practices with the global mining sector; 2. The comparative method of inquiry, where the comparison was made between environmental protection practices as implemented in the US (developed country) and the developing countries such as RF, Mongolia mining sectors; 3. Quantitative date analysis, where date was collected from "The collection of statistic data", Russian Geographic Society Annual reports, the US EPA open reports, and the USGS Reports; The following results were obtained: Identified the systemic crisis of the ecological environmental policies and practices in the mining sector in developing countries based on the exploitation of nonrenewable resources, absence of the ecological interest by the mining companies that lack mechanisms of environmental and public health protection, the lack of insurance policy, the lack of risk assistance, and in the presence of the audit and monitoring that do not address the local conditions of the mining operations. Based on the above the following concepts were thought of to improve the environmental conditions in mining sector: 1. Was developed the Regional Environmental Management principle based on the local conditions such as physiographic region, local population, and socioeconomic conditions of the area; 2. Devised were criteria for the risk assessment for developing countries. Where the fundamental principals were public health, both near and far from the operation, environmental and biodiversity impact, waste management, long- and short- term rehabilitation plans, compliance with international standards and norms. 3. Developed was the mechanism of the economic motivation to make mining operations "environmentally friendly" that includes defrayal of expenses from both direct and indirect damages. 4. Identified were spheres of possible cooperation between mining companies, government organizations, and the NGOs. These include development of international standards for Good Neighbor Agreement, exchange of environmental information, exchange of successful environmental, health, and safety practices between mining operations from developed and developing countries. The study showed the dire necessity for the mining industry that operates in developing countries to adopt the successful environmental practices used in developed countries. To achieve this goal the Regional Environmental Management principle, the risk assessment criteria, the mechanism of the economic motivation and the principles for international cooperation can play an extremely important role.

Stream biological surveys - self-defense for coal mine operators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hampton, E.L.; Pennington, W.L.; Lackey, J.L.

1979-12-01

According to Section 779.20 of the Permanent Regulatory Program Regulations, Surface Coal Mining and Reclamation Operations, Department of the Interior, office of Surface Mining Reclamation and Enforcement, coal mine operators must provide information on fish and wildlife resources in order to obtain mining permits. Although considered to be a liability by many mine operators, stream biological surveys can, in reality, become a significant asset. When combined with appropriate water quality measurements, stream biological surveys can adequately assess a stream's health. Although initially adding cost, stream biological surveys can actually save money and potential litigation during the mining period. However, streammore » biological surveys must be conducted before any mining activity is initiated and should continue on a periodic basis thereafter. Only in this manner can mine operators be assured that biological measurements made on streams affected by their operation are accurate reflections of pre- and post-mining conditions. Armed with this vital information, mine operators have a basis to defend against any unjustified claims that their operations are having deleterious effects on the stream in question. This paper addresses the purpose, scope, methodology, and interpretation of results of stream biological surveys. Additionally, methods for utilizing information from stream biological surveys will be stressed.« less

Unmanned Surface Combatant Considerations for Concept Exploration

DTIC Science & Technology

2011-06-01

counterparts who become fatigued. The USC systems could perform missions without having to consider the health and morale of the crew. 18 Arguably the...fourth objective was to evaluate the USC relevant technologies and identify potential design issues . The result was relevant technologies that...and issue mines. R MIW 8 (U) Conduct precise navigation. G MIW 9 (U) Conduct airborne mine countermeasures. R MIW 10 (U) Provide for air operations

Power System Transient Stability Based on Data Mining Theory

NASA Astrophysics Data System (ADS)

Cui, Zhen; Shi, Jia; Wu, Runsheng; Lu, Dan; Cui, Mingde

2018-01-01

In order to study the stability of power system, a power system transient stability based on data mining theory is designed. By introducing association rules analysis in data mining theory, an association classification method for transient stability assessment is presented. A mathematical model of transient stability assessment based on data mining technology is established. Meanwhile, combining rule reasoning with classification prediction, the method of association classification is proposed to perform transient stability assessment. The transient stability index is used to identify the samples that cannot be correctly classified in association classification. Then, according to the critical stability of each sample, the time domain simulation method is used to determine the state, so as to ensure the accuracy of the final results. The results show that this stability assessment system can improve the speed of operation under the premise that the analysis result is completely correct, and the improved algorithm can find out the inherent relation between the change of power system operation mode and the change of transient stability degree.

The effect of vibration exposure during haul truck operation on grip strength, touch sensation, and balance

PubMed Central

Pollard, Jonisha; Porter, William; Mayton, Alan; Xu, Xueyan; Weston, Eric

2017-01-01

Falls from mobile equipment are reported at surface mine quarry operations each year in considerable numbers. Research shows that a preponderance of falls occur while getting on/off mobile equipment. Contributing factors to the risk of falls include the usage of ladders, exiting onto a slippery surface, and foot or hand slippage. Balance issues may also contribute to fall risks for mobile equipment operators who are exposed to whole-body vibration (WBV). For this reason, the National Institute for Occupational Safety and Health, Office of Mine Safety and Health Research conducted a study at four participating mine sites with seven haul truck operators. The purpose was to ascertain whether WBV and hand-arm vibration (HAV) exposures for quarry haul truck operators were linked to short-term decreases in performance in relation to postural stability, touch sensation threshold, and grip strength that are of crucial importance when getting on/off the trucks. WBV measures of frequency-weighted RMS accelerations (wRMS) and vibration dose value (VDV), when compared to the ISO/ANSI standards, were mostly below levels identified for the Health Guidance Caution Zone (HGCZ), although there were instances where the levels were within and above the specified Exposure Action Value. Comparably, all mean HAV levels, when compared to the ISO/ANSI standards, were below the HGCZ. For the existing conditions and equipment, no significant correlation could be identified between the WBV, HAV, postural stability, touch sensation threshold, and grip strength measures taken during this study. PMID:28220051

43 CFR 3482.3 - Mining operations maps.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Mining operations maps. 3482.3 Section... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) COAL EXPLORATION AND MINING OPERATIONS RULES Exploration and Resource Recovery and Protection Plans § 3482.3 Mining operations maps. (a...

Landfill mining: Development of a cost simulation model.

PubMed

Wolfsberger, Tanja; Pinkel, Michael; Polansek, Stephanie; Sarc, Renato; Hermann, Robert; Pomberger, Roland

2016-04-01

Landfill mining permits recovering secondary raw materials from landfills. Whether this purpose is economically feasible, however, is a matter of various aspects. One is the amount of recoverable secondary raw material (like metals) that can be exploited with a profit. Other influences are the costs for excavation, for processing the waste at the landfill site and for paying charges on the secondary disposal of waste. Depending on the objectives of a landfill mining project (like the recovery of a ferrous and/or a calorific fraction) these expenses and revenues are difficult to assess in advance. This situation complicates any previous assessment of the economic feasibility and is the reason why many landfills that might be suitable for landfill mining are continuingly operated as active landfills, generating aftercare costs and leaving potential hazards to later generations. This article presents a newly developed simulation model for landfill mining projects. It permits identifying the quantities and qualities of output flows that can be recovered by mining and by mobile on-site processing of the waste based on treatment equipment selected by the landfill operator. Thus, charges for disposal and expected revenues from secondary raw materials can be assessed. Furthermore, investment, personnel, operation, servicing and insurance costs are assessed and displayed, based on the selected mobile processing procedure and its throughput, among other things. For clarity, the simulation model is described in this article using the example of a real Austrian sanitary landfill. © The Author(s) 2016.

30 CFR 57.22203 - Main fan operation (I-C mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main fan operation (I-C mines). 57.22203... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22203 Main fan operation (I-C mines). Main fans shall be operated continuously while ore production is in progress. ...

75 FR 18500 - Guidance on Improving EPA Review of Appalachian Surface Coal Mining Operations under the Clean...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-12

... of Appalachian Surface Coal Mining Operations under the Clean Water Act, National Environmental... Appalachian Surface Coal Mining Operations under the Clean Water Act, National Environmental Policy Act, and... coal mining operations under the Clean Water Act, National Environmental Policy Act, and the...

30 CFR 49.13 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines... the operator as to the number of miners willing to serve on a mine rescue team; (8) The operator's...

30 CFR 49.13 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines... the operator as to the number of miners willing to serve on a mine rescue team; (8) The operator's...

30 CFR 49.13 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines... the operator as to the number of miners willing to serve on a mine rescue team; (8) The operator's...

30 CFR 49.13 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines... the operator as to the number of miners willing to serve on a mine rescue team; (8) The operator's...

30 CFR 49.13 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines... the operator as to the number of miners willing to serve on a mine rescue team; (8) The operator's...

30 CFR 761.11 - Areas where surface coal mining operations are prohibited or limited.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Areas where surface coal mining operations are....11 Areas where surface coal mining operations are prohibited or limited. You may not conduct surface coal mining operations on the following lands unless you either have valid existing rights, as...

30 CFR 761.11 - Areas where surface coal mining operations are prohibited or limited.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas where surface coal mining operations are....11 Areas where surface coal mining operations are prohibited or limited. You may not conduct surface coal mining operations on the following lands unless you either have valid existing rights, as...

42 CFR 37.100 - Coal mine operator plan for medical examinations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Coal mine operator plan for medical examinations... MEDICAL CARE AND EXAMINATIONS SPECIFICATIONS FOR MEDICAL EXAMINATIONS OF COAL MINERS General Requirements § 37.100 Coal mine operator plan for medical examinations. (a) Each coal mine operator must submit and...

30 CFR 761.11 - Areas where surface coal mining operations are prohibited or limited.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Areas where surface coal mining operations are....11 Areas where surface coal mining operations are prohibited or limited. You may not conduct surface coal mining operations on the following lands unless you either have valid existing rights, as...

76 FR 13600 - Payette National Forest, Idaho, Golden Hand #3 and #4 Lode Mining Claims, Plan of Operations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

.... 3 and No. 4 Lode Mining Claims Proposed Plan of Operations. The project included mining operations on the lode claims along with associated activities such as road maintenance and construction. The... Mining Claims, Plan of Operations AGENCY: Forest Service, USDA. ACTION: Notice of withdrawal. SUMMARY...

Ground penetrating radar coal measurements demonstration at the U.S. Bureau of Mines Research Center, Pittsburgh, Pennsylvania. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gardner, D.; Guerrier, J.; Martinez, M.

1994-01-04

In situ and near real-time measurements of coal seam thickness have been identified by industry as a highly desirable component of robotic mining systems. With it, a continuous mining machine can be guided close to the varying boundary of the seam while the cutting operation is underway. This provides the mining operation the ability to leave behind the high-sulfur, high-particulate coal which is concentrated near the seam boundary. The result is near total recovery of high quality coal resources, an increase in mining efficiency, and opportunities for improved safety through reduction in personnel in the most hazardous coal cutting areas.more » In situ, real-time coal seam measurements using the Special Technologies Laboratory (STL) ground penetrating radar (GPR) technology were shown feasible by a demonstration in a Utah coal mine on April 21, 1994. This report describes the October 18, 1994 in situ GPR measurements of coal seam thickness at the US Bureau of Mines (USBM) robotic mining testing laboratory. In this report, an overview of the measurements at the USBM Laboratory is given. It is followed by a description of the technical aspects of the STL frequency modulated-continuous wave (FM-CW) GPR system. Section 4 provides a detailed description of the USBM Laboratory measurements and the conditions under which they were taken. Section 5 offers conclusions and possibilities for future communications.« less

Description of basic mining legal principles.

PubMed

Schmidt, Reinhard

2014-01-01

The Federal Mining Act manages access, via the system of mining concessions, to areas free for mining natural resources that do not belong to the surface property and deposits' owner. These cover especially important natural resources for the economy, including coal, ore, salt, crude oil and natural gas, and also terrestrial heat. For mining operations there exist, however, the same decrees for natural resources in the property of the surface owners, which are predominantly higher-value industrial minerals such as roofing slate, basalt, quartz sand, and clays for the fireproofing industry. In the case of mining laws, administrative procedures such as issuing mining concessions, approving operating plans, and issuing permits or licenses to explore according to water rights or the Federal Immission Control Act, those authorities and departments in whose remit the projects fall are dealt with by the Mining Authority. This means that the Mining Authority is the only state point of contact for the applicant, essentially an "all-in-one" service as it will itself instigate any further participation procedures required. The classic licensing procedure of mining is the operations plan procedure, whereby the operator submits an operating plan to the Mining Authority, which then examines it to ensure it fulfills mandatory legal safety objectives. If necessary these safety objectives can be met during licensing of the operating plans by stipulating additional requirements, Depending on the subject and validity period there are overall operating plans having the widest possible remit with comprehensive participation by the authorities and basic operating plans that form the basis for every mining works. There are also special operating plans, which owing to the dynamics of mining, resolve matters that suddenly become necessary or when the basic operating plans as originally conceived were not relevant. The closing-down operating plan is the designated tool for closing down works and for the rehabilitation of the land; in the case of underground mining and mine boreholes an operating history must also be submitted. For those projects that have a significant effect on the environment, an obligatory overall operations plan with mining law project approval procedure and integrated Environmental Risk Assessment (UVP) are necessary. The point at which this is required is stipulated in the UVP-mining decree, for example if the mining area of an open-cast pit is more than 25 ha. Alongside the UVP, the procedure is also equipped with public participation and through its "concentrating effect" replaces further licensing procedures according to other laws. The Mining Authority combines supervision and licensing, which are usually inseparable due to the operations plan procedure, as well as aspects of occupational safety and of the protection of the environment. In view of this administrative concentration these should not be fragmented. The "all-in-one" service meets the requirements of a modern public-oriented administration, has only a few points of contact, and can therefore work efficiently.

Hydrologic assessment and numerical simulation of groundwater flow, San Juan Mine, San Juan County, New Mexico, 2010–13

USGS Publications Warehouse

Stewart, Anne M.

2018-04-03

Coal combustion byproducts (CCBs), which are composed of fly ash, bottom ash, and flue gas desulfurization material, produced at the coal-fired San Juan Generating Station (SJGS), located in San Juan County, New Mexico, have been buried in former surface-mine pits at the San Juan Mine, also referred to as the San Juan Coal Mine, since operations began in the early 1970s. This report, prepared by the U.S. Geological Survey in cooperation with the Mining and Minerals Division of the New Mexico Energy, Minerals and Natural Resources Department, describes results of a hydrogeologic assessment, including numerical groundwater modeling, to identify the timing of groundwater recovery and potential pathways for groundwater transport of metals that may be leached from stored CCBs and reach hydrologic receptors after operations cease. Data collected for the hydrologic assessment indicate that groundwater in at least one centrally located reclaimed surface-mining pit has already begun to recover.The U.S. Geological Survey numerical modeling package MODFLOW–NWT was used with MODPATH particle-tracking software to identify advective flow paths from CCB storage areas toward potential hydrologic receptors. Results indicate that groundwater at CCB storage areas will recover to the former steady state, or in some locations, groundwater may recover to a new steady state in 6,600 to 10,600 years at variable rates depending on the proximity to a residual cone-of-groundwater depression caused by mine dewatering and regional oil and gas pumping as well as on actual, rather than estimated, groundwater recharge and evapotranspirational losses. Advective particle-track modeling indicates that the number of particles and rates of advective transport will vary depending on hydraulic properties of the mine spoil, particularly hydraulic conductivity and porosity. Modeling results from the most conservative scenario indicate that particles can migrate from CCB repositories to either the Shumway Arroyo alluvium after 1,320 years and from there to the San Juan River alluvium after 1,520 years or from southernmost CCB repositories directly to the San Juan River alluvium after 2,400 years after the cessation of mining.

30 CFR 780.27 - Reclamation plan: Surface mining near underground mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RECLAMATION AND OPERATION PLAN § 780.27 Reclamation plan: Surface mining near underground mining. For surface... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Reclamation plan: Surface mining near... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL...

Critical parameters for coarse coal underground slurry haulage systems

NASA Technical Reports Server (NTRS)

Maynard, D. P.

1981-01-01

Factors are identified which must be considered in meeting the requirements of a transportation system for conveying, in a pipeline, the coal mined by a continuous mining machine to a storage location neat the mine entrance or to a coal preparation plant located near the surface. For successful operation, the slurry haulage the system should be designed to operated in the turbulent flow regime at a flow rate at least 30% greater than the deposition velocity (slurry flow rate at which the solid particles tend to settle in the pipe). The capacity of the haulage system should be compatible with the projected coal output. Partical size, solid concentration, density, and viscosity of the suspension are if importance as well as the selection of the pumps, pipes, and valves. The parameters with the greatest effect on system performance ar flow velocity, pressure coal particle size, and solids concentration.

UNCOMPAHGRE PRIMITIVE AREA, COLORADO.

USGS Publications Warehouse

Luedke, R.G.; Sheridan, M.J.

1984-01-01

A mineral-resource study was made of that part of the Uncompahgre National Forest, Colorado constituting the officially designated primitive area. Because the primitive area and its southern border zone contained operating mines producing gold, silver, copper, lead, zinc, and minor amounts of a few other metals, and had been a part of a highly productive mining region, the area was concluded to have large segments of both probable and substantiated mineral-resource potential. No energy resources were identified in the study.

Space assets for demining assistance

NASA Astrophysics Data System (ADS)

Kruijff, Michiel; Eriksson, Daniel; Bouvet, Thomas; Griffiths, Alexander; Craig, Matthew; Sahli, Hichem; González-Rosón, Fernando Valcarce; Willekens, Philippe; Ginati, Amnon

2013-02-01

Populations emerging from armed conflicts often remain threatened by landmines and explosive remnants of war. The international mine action community is concerned with the relief of this threat. The Space Assets for Demining Assistance (SADA) undertaking is a set of activities that aim at developing new services to improve the socio-economic impact of mine action activities, primarily focused on the release of land thought to be contaminated, a process described as land release. SADA was originally initiated by the International Astronautical Federation (IAF). It has been implemented under the Integrated Applications Promotion (IAP) program of the European Space Agency (ESA). Land release in mine action is the process whereby the demining community identifies, surveys and prioritizes suspected hazardous areas for more detailed investigation, which eventually results in the clearance of landmines and other explosives, thereby releasing land to the local population. SADA has a broad scope, covering activities, such as planning (risk and impact analysis, prioritization, and resource management), field operations and reporting. SADA services are developed in two phases: feasibility studies followed by demonstration projects. Three parallel feasibility studies have been performed. They aimed at defining an integrated set of space enabled services to support the land release process in mine action, and at analyzing their added value, viability and sustainability. The needs of the mine action sector have been assessed and the potential contribution of space assets has been identified. Support services have been formulated. To test their fieldability, proofs of concept involving mine action end users in various operational field settings have been performed by each of the study teams. The economic viability has also been assessed. Whenever relevant and cost-effective, SADA aims at integrating Earth observation data, GNSS navigation and SatCom technologies with existing mine action tools and procedures, as well as with novel aerial survey technologies. Such conformity with existing user processes, as well as available budgets and appropriateness of technology based solutions given the field level operational setting are important conditions for success. The studies have demonstrated that Earth observation data, satellite navigation solutions and in some cases, satellite communication, indeed can provide added value to mine action activities if properly tailored based on close user interaction and provided through a suitable channel. Such added value for example includes easy and sustained access to Earth observation data for general purpose mapping, land use assessment for post-release progress reporting, and multi-source data fusion algorithms to help quantify risks and socio-economic impact for prioritization and planning purposes. The environment and boundaries of a hazardous area can also be better specified to support the land release process including detailed survey and clearance operations. Satellite communication can help to provide relevant data to remote locations, but is not regarded as strongly user driven. Finally, satellite navigation can support more precise non-technical surveys, as well as aerial observation with small planes or hand-launched UAV's. To ensure the activity is genuinely user driven, the Geneva International Center for Humanitarian Demining (GICHD) plays an important role as ESA's external advisor. ESA is furthermore supported by a representative field operator, the Swiss Foundation of Mine Action (FSD), providing ESA with a direct connection to the field level end users. Specifically FSD has provided a shared user needs baseline to the three study teams. To ensure solutions meet with end user requirements, the study teams themselves include mine action representatives and have interacted closely with their pre-existing and newly established contacts within the mine action community.

Advantages and difficulties of implementation of the international GNA standards in sustainable mining development. (Invited)

NASA Astrophysics Data System (ADS)

Masaitis, A.

2013-12-01

Conflicts in the development of mining projects are now common between the mining proponents, NGO's and communities. These conflicts can sometimes be alleviated by early development of modes of communication, and a formal discussion format that allows airing of concerns and potential resolution of problems. One of the methods that can formalize this process is to establish a Good Neighbor Agreement (GNA), which deals specifically with challenges in relationships between mining operations and the local communities. It is a new practice related to mining operations that are oriented toward social needs and concerns of local communities that arise during the normal life of a mine, which can achieve sustainable mining practices in both developing and developed countries. The GNA project being currently developed at the University of Nevada, Reno in cooperation with the Newmont Mining Corporation has a goal to create an open company/community dialog that is based on the international standards and that will help identify and address sociological and environmental concerns associated with mining, as well as find methods for communication and conflict resolution. GNA standards should be based on trust doctrine, open information access, and community involvement in the decision making process. It should include the following components: emergency response and community communications; environmental issues, including air and water quality standards; reclamation and recultivation; socio-economic issues: transportation, safety, training, and local hiring; and financial issues, particularly related to mitigation offsets and community needs. The GNA standards help identify and evaluate conflict criteria in mining/community relationships; determine the status of concerns; focus on the local political and government systems; separate the acute and the chronic concerns; determine the role and responsibilities of stakeholders; analyze problem resolution feasibility; maintain the community involvement and support through economic benefits and environmental safeguards; develop options for the concerns resolution; develop and manage short and long-term plans. Difficulties in establishing the GNA standards include identification of the full list of stakeholders, lack of responsible environmental protection practices, dependence on the government and political system, lack of will to disclose full information to the public. It is further complicated by the lack of insurance/bonding policies, and by the lack of audit and monitoring that could determine the level of exposure of the local community and the environment to the contaminants released at the mine sites. Since many problems of mines can occur during closure and post-closure, GNA's should address those issues also. Determined the process for the GNA implementation as a conflict prevention/resolution tool, analyzed conflict/concerns criteria associated with mining operations, determined the role of the stakeholders, worked out the process of stakeholders monitoring, carried out the sociological survey of the stakeholders and the community. Frequent conflicts between mining companies and surrounding communities that lead to work disruptions or even mine closures show the necessity of a less confrontational approach to environmental and social justice. Establishment of GNA standards for use in both developed and developing nations can decrease these conflicts.

Determine utility of ERTS-1 to detect and monitor area strip mining and reclamation. [southeastern Ohio

NASA Technical Reports Server (NTRS)

Rogers, R. H. (Principal Investigator); Pettyjohn, W. A.

1975-01-01

The author has identified the following significant results. Computer techniques were applied to process ERTS tapes acquired over coal mining operations in southeastern Ohio on 21 August 1972 and 3 September 1973. ERTS products obtained included geometrically correct map overlays showing stripped earth, partially reclaimed earth, water, and natural vegetation. Computer-generated tables listing the area covered by each land-water category in square kilometers and acres were produced. By comparing these mapping products, the study demonstrates the capability of ERTS to monitor changes in the extent of stripping, success of reclamation, and the secondary effects of mining on the environment.

30 CFR 785.12 - Special bituminous surface coal mining and reclamation operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Special bituminous surface coal mining and... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL....12 Special bituminous surface coal mining and reclamation operations. (a) This section applies to any...

30 CFR 785.12 - Special bituminous surface coal mining and reclamation operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Special bituminous surface coal mining and... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL....12 Special bituminous surface coal mining and reclamation operations. (a) This section applies to any...

30 CFR 785.11 - Anthracite surface coal mining and reclamation operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Anthracite surface coal mining and reclamation..., DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION... Anthracite surface coal mining and reclamation operations. (a) This section applies to any person who...

30 CFR 785.12 - Special bituminous surface coal mining and reclamation operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Special bituminous surface coal mining and... ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL....12 Special bituminous surface coal mining and reclamation operations. (a) This section applies to any...

30 CFR 785.11 - Anthracite surface coal mining and reclamation operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Anthracite surface coal mining and reclamation..., DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION... Anthracite surface coal mining and reclamation operations. (a) This section applies to any person who...

30 CFR 785.11 - Anthracite surface coal mining and reclamation operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Anthracite surface coal mining and reclamation..., DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION... Anthracite surface coal mining and reclamation operations. (a) This section applies to any person who...

30 CFR 785.11 - Anthracite surface coal mining and reclamation operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Anthracite surface coal mining and reclamation..., DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION... Anthracite surface coal mining and reclamation operations. (a) This section applies to any person who...

30 CFR 785.11 - Anthracite surface coal mining and reclamation operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Anthracite surface coal mining and reclamation..., DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION... Anthracite surface coal mining and reclamation operations. (a) This section applies to any person who...

43 CFR 3484.1 - Performance standards for exploration and surface and underground mining.

Code of Federal Regulations, 2014 CFR

2014-10-01

... officer. Operators/lessees of underground coal mines shall adopt measures consistent with known technology... subsequent operations on the quantity, quality, or pressure of ground water or mine gases only with the... mines—(1) Underground resource recovery. Underground mining operations shall be conducted so as to...

43 CFR 3484.1 - Performance standards for exploration and surface and underground mining.

Code of Federal Regulations, 2011 CFR

2011-10-01

... officer. Operators/lessees of underground coal mines shall adopt measures consistent with known technology... subsequent operations on the quantity, quality, or pressure of ground water or mine gases only with the... mines—(1) Underground resource recovery. Underground mining operations shall be conducted so as to...

Using Geostationary Communications Satellites as a Sensor: Telemetry Search Algorithms

NASA Astrophysics Data System (ADS)

Cahoy, K.; Carlton, A.; Lohmeyer, W. Q.

2014-12-01

For decades, operators and manufacturers have collected large amounts of telemetry from geostationary (GEO) communications satellites to monitor system health and performance, yet this data is rarely mined for scientific purposes. The goal of this work is to mine data archives acquired from commercial operators using new algorithms that can detect when a space weather (or non-space weather) event of interest has occurred or is in progress. We have developed algorithms to statistically analyze power amplifier current and temperature telemetry and identify deviations from nominal operations or other trends of interest. We then examine space weather data to see what role, if any, it might have played. We also closely examine both long and short periods of time before an anomaly to determine whether or not the anomaly could have been predicted.

Greenhouse Gases and Energy Intensity of Granite Rock Mining Operations in Thailand: A Case of Industrial Rock-Construction

NASA Astrophysics Data System (ADS)

Kittipongvises, Suthirat; Chavalparit, Orathai; Sutthirat, Chakkaphan

2016-12-01

This paper is aimed to systematically assess greenhouse gases (GHGs) and energy intensity of the granite rock mining operations in Thailand and also identify a range of feasible options to minimize their GHG emissions. Mining factories A, B and C, located in the Eastern region of Thailand, were selected as research case studies. The results indicated that the 3-year average of GHGs emissions from factories A to C was 3387 718 kgCO2e per year with approximately 2.92 kgCO2e per ton of granite rock produced over 2012 to 2014. Of this, the carbon intensity of grid-electricity consumption for the crushed rock production was 1.84 kgCO2/kWh. Diesel fuel combustion for transport activities in the mining factories was the greatest contributor to GHGs emissions (68 %) compared to the purchased electricity and explosion process, with 31 % and 1 %, respectively. In-Pit Crushing and Conveying (IPCC) installation, haul truck payload optimization and management, and reduction in tire rolling resistance have shown potential to reduce carbon emissions accounted for 20 % to 70 %.

Whole body vibration exposure in heavy earth moving machinery operators of metalliferrous mines.

PubMed

Vanerkar, A P; Kulkarni, N P; Zade, P D; Kamavisdar, A S

2008-08-01

As mining operations get mechanized, the rate of profit generation increases and so do the rate of occupational hazards. This study deals with one such hazard - occupational vibration. The present study was carried out to determine the whole body vibration (WBV) exposure of the heavy earth moving machinery (HEMM) operators in two types of metalliferous mines in India, when they were engaged in the mining activity. Cross-comparison was done of the vibration dose value (VDV) for HEMM operators as well as each type of mine. The VDV for the shovel operator in bauxite mine was observed to be 13.53 +/- 5.63 m/s(7/4) with 25% of the readings higher than the prescribed limit whereas in iron ore mine VDV for dumper operator was 10.81 +/- 3.44 m/s(7/4) with 14.62% readings on the higher side. Cross-comparison of the VDV values for bauxite and iron ore mines revealed that it was 9.57 +/- 4.93 and 8.21 +/- 5.12 m/s(7/4) with 21.28 and 14.95% of the readings on the higher side respectively. The Student's t test level was found to be insignificant for both type of mines, indicating that the WBV exposure is not dependent on the type of mine but is dependent on the working condition and type of HEMM in operation.

Exploring the use of situation awareness in behaviors and practices of health and safety leaders

PubMed Central

Willmer, D.R.

2018-01-01

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others. PMID:29593373

Sustainable Bauxite Mining — A Global Perspective

NASA Astrophysics Data System (ADS)

Wagner, Christian

In 2008 the International Aluminium Institute commissioned its fourth sustainable bauxite mining report with the aim to collect global data on the environmental, social and economic impacts of bauxite mining operations and their rehabilitation programmes. The report shows that bauxite mining has become sustainable and land area footprint neutral;it is a relatively small land use operation when compared to most other types of mining. All operations have clearly defined rehabilitation objectives, fully integrated rehabilitation programmes, and written rehabilitation procedures. The rehabilitation objectives can be summarized as follows: "The bauxite mining operations aim to restore pre-mining environment and the respective conditions; this can be a self-sustaining ecosystem consisting of native flora and fauna or any other land-use to the benefit of the local community".

Section of Cybernetics in Mining of Mining Committee of Polish Academy of Sciences - Pro Memoria

NASA Astrophysics Data System (ADS)

Wojaczek, Antoni; Miśkiewicz, Kazimierz

2017-09-01

Section of Cybernetics in Mining of Mining Committee of Polish Academy of Science (PAN) has been created by PAN Mining Committee in 1969. It was a section in Mining Committee of PAN, whose operation range included widely understood issues of automation, telecommunication and informatics in mining industry. The main operation method of the Section was to organize the periodic conferences dedicated to issues of control systems in mining. The first conference took place in 1971 in Katowice. Together with new (the current one) term of office of Mining Committee of PAN this Section ceased to exist. The paper presents (pro memoria) over 40 year long conference output of this Section that functioned within the scope of operation of Mining Committee of PAN up to 12th January 2016.

30 CFR 905.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface coal mining operations. 905.764 Section 905.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE CALIFORNIA § 905.764 Process for designating areas unsuitable for surface coal mining operations. Part 764 of this chapter, State Processes for Designating Areas Unsuitable for Surface Coal...

30 CFR 910.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface coal mining operations. 910.764 Section 910.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE GEORGIA § 910.764 Process for designating areas unsuitable for surface coal mining operations. Part 764 of this chapter, State Processes for Designating Areas Unsuitable for Surface Coal...

30 CFR 912.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface coal mining operations. 912.764 Section 912.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE IDAHO § 912.764 Process for designating areas unsuitable for surface coal mining operations. Part 764 of this chapter, State Processes for Designating Areas Unsuitable for Surface Coal...

30 CFR 903.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface coal mining operations. 903.764 Section 903.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE ARIZONA § 903.764 Process for designating areas unsuitable for surface coal mining operations. Part 764 of this chapter, State Processes for Designating Areas Unsuitable for Surface Coal...

75 FR 79016 - Notice of Availability of the Final Environmental Impact Statement for the Newmont Mining...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-17

... Newmont Mining Corporation Emigrant Project Plan of Operation, Nevada AGENCY: Bureau of Land Management... Mining Corporation Emigrant Project Plan of Operations and by this notice is announcing its availability...: Copies of the EIS for the Newmont Mining Corporation Emigrant Project Plan of Operation are available for...

Mines Systems Safety Improvement Using an Integrated Event Tree and Fault Tree Analysis

NASA Astrophysics Data System (ADS)

Kumar, Ranjan; Ghosh, Achyuta Krishna

2017-04-01

Mines systems such as ventilation system, strata support system, flame proof safety equipment, are exposed to dynamic operational conditions such as stress, humidity, dust, temperature, etc., and safety improvement of such systems can be done preferably during planning and design stage. However, the existing safety analysis methods do not handle the accident initiation and progression of mine systems explicitly. To bridge this gap, this paper presents an integrated Event Tree (ET) and Fault Tree (FT) approach for safety analysis and improvement of mine systems design. This approach includes ET and FT modeling coupled with redundancy allocation technique. In this method, a concept of top hazard probability is introduced for identifying system failure probability and redundancy is allocated to the system either at component or system level. A case study on mine methane explosion safety with two initiating events is performed. The results demonstrate that the presented method can reveal the accident scenarios and improve the safety of complex mine systems simultaneously.

Influence of continuous mining arrangements on respirable dust exposures

PubMed Central

Beck, T. W.; Organiscak, J. A.; Pollock, D. E.; Potts, J. D.; Reed, W. R.

2017-01-01

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remote-controlled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures. PMID:28529441

Strengths amidst vulnerabilities: the paradox of resistance in a mining-affected community in Guatemala.

PubMed

Caxaj, C Susana; Berman, Helene; Ray, Susan L; Restoule, Jean-Paul; Varcoe, Coleen

2014-11-01

The influence of large-scale mining on the psychosocial wellbeing and mental health of diverse Indigenous communities has attracted increased attention. In previous reports, we have discussed the influence of a gold mining operation on the health of a community in the Western highlands of Guatemala. Here, we discuss the community strengths, and acts of resistance of this community, that is, community processes that promoted mental health amidst this context. Using an anti-colonial narrative methodology that incorporated participatory action research principles, we developed a research design in collaboration with community leaders and participants. Data collection involved focus groups, individual interviews and photo-sharing with 54 men and women between the ages of 18 and 67. Data analysis was guided by iterative and ongoing conversations with participants and McCormack's narrative lenses. Study findings revealed key mechanisms and sources of resistance, including a shared cultural identity, a spiritual knowing and being, 'defending our rights, defending our territory,' and, speaking truth to power. These overlapping strengths were identified by participants as key protective factors in facing challenges and adversity. Yet ultimately, these same strengths were often the most eroded or endangered due the influence of large-scale mining operations in the region. These community strengths and acts of resistance reveal important priorities for promoting mental health and wellbeing for populations impacted by large-scale mining operations. Mental health practitioners must attend to both the strengths and parallel vulnerabilities that may be occasioned by large-scale projects of this nature.

30 CFR 75.301 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.301 Definitions. In addition to the applicable... operator. The person(s), designated by the mine operator, who is located on the surface of the mine and...

30 CFR 75.301 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.301 Definitions. In addition to the applicable... operator. The person(s), designated by the mine operator, who is located on the surface of the mine and...

30 CFR 75.301 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.301 Definitions. In addition to the applicable... operator. The person(s), designated by the mine operator, who is located on the surface of the mine and...

Coal supply for California

NASA Technical Reports Server (NTRS)

Yancik, J. J.

1978-01-01

The potential sources and qualities of coals available for major utility and industrial consumers in California are examined and analyzed with respect to those factors that would affect the reliability of supplies. Other considerations, such as the requirements and assurances needed by the coal producers to enter into long-term contracts and dedicate large reserves of coal to these contracts are also discussed. Present and potential future mining contraints on coal mine operators are identified and analyzed with respect to their effect on availability of supply.

An Approach to Realizing Process Control for Underground Mining Operations of Mobile Machines

PubMed Central

Song, Zhen; Schunnesson, Håkan; Rinne, Mikael; Sturgul, John

2015-01-01

The excavation and production in underground mines are complicated processes which consist of many different operations. The process of underground mining is considerably constrained by the geometry and geology of the mine. The various mining operations are normally performed in series at each working face. The delay of a single operation will lead to a domino effect, thus delay the starting time for the next process and the completion time of the entire process. This paper presents a new approach to the process control for underground mining operations, e.g. drilling, bolting, mucking. This approach can estimate the working time and its probability for each operation more efficiently and objectively by improving the existing PERT (Program Evaluation and Review Technique) and CPM (Critical Path Method). If the delay of the critical operation (which is on a critical path) inevitably affects the productivity of mined ore, the approach can rapidly assign mucking machines new jobs to increase this amount at a maximum level by using a new mucking algorithm under external constraints. PMID:26062092

An Approach to Realizing Process Control for Underground Mining Operations of Mobile Machines.

PubMed

Song, Zhen; Schunnesson, Håkan; Rinne, Mikael; Sturgul, John

2015-01-01

The excavation and production in underground mines are complicated processes which consist of many different operations. The process of underground mining is considerably constrained by the geometry and geology of the mine. The various mining operations are normally performed in series at each working face. The delay of a single operation will lead to a domino effect, thus delay the starting time for the next process and the completion time of the entire process. This paper presents a new approach to the process control for underground mining operations, e.g. drilling, bolting, mucking. This approach can estimate the working time and its probability for each operation more efficiently and objectively by improving the existing PERT (Program Evaluation and Review Technique) and CPM (Critical Path Method). If the delay of the critical operation (which is on a critical path) inevitably affects the productivity of mined ore, the approach can rapidly assign mucking machines new jobs to increase this amount at a maximum level by using a new mucking algorithm under external constraints.

Insertion loss of noise barriers on an aboveground, full-scale model longwall coal mining shearer.

PubMed

Sweeney, Daniel D; Slagley, Jeremy M; Smith, David A

2010-05-01

The U.S. mining industry struggles with hazardous noise and dust exposures in underground mining. Specifically, longwall coal mine shearer operators are routinely exposed to noise levels at 151% of the allowable daily dose, and approximately 20% exceed regulatory dust levels. In the current study, a partial barrier was mounted on the full-scale mock shearer at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory. A simulated, full-scale, coal mine longwall shearer operation was employed to test the feasibility of utilizing a barrier to separate the shearer operator from the direct path of the noise and dust source during mining operations. In this model, noise levels at the operators' positions were reduced by 2.6 to 8.2 A-weighted decibels (dBA) from the application of the test barriers. Estimated insertion loss underground was 1.7 to 7.3 dBA. The barrier should be tested in an underground mining operation to determine if it can reduce shearer operators' noise exposure to below regulatory limits.

77 FR 57111 - Agency Information Collection Activities: Comment Request for the Mine, Development, and Mineral...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-17

...: Private sector: U.S. nonfuel minerals producers and exploration operations; Public sector: State and local.... While you can ask us in your comment to withhold your personal identifying information from public...

30 CFR 772.12 - Permit requirements for exploration that will remove more than 250 tons of coal or that will...

Code of Federal Regulations, 2010 CFR

2010-07-01

... mining operations. 772.12 Section 772.12 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL... unsuitable for surface coal mining operations. (a) Exploration permit. Any person who intends to conduct coal...

30 CFR 784.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.1 Scope. This part... mining operations and reclamation plans portions of applications for permits for underground mining...

30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., forest, recreation area, or places; (f)(1) Where the proposed surface coal mining operation may adversely... mining by Act of Congress. 933.761 Section 933.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS...

30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., forest, recreation area, or places; (f)(1) Where the proposed surface coal mining operation may adversely... mining by Act of Congress. 933.761 Section 933.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS...

30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., forest, recreation area, or places; (f)(1) Where the proposed surface coal mining operation may adversely... mining by Act of Congress. 933.761 Section 933.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS...

30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., forest, recreation area, or places; (f)(1) Where the proposed surface coal mining operation may adversely... mining by Act of Congress. 933.761 Section 933.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS...

Sampling and monitoring for closure

USGS Publications Warehouse

McLemore, V.T.; Russell, C.C.; Smith, K.S.

2004-01-01

The Metals Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS) addresses technical drainage-quality issues related to metal mining and related metallurgical operations, for future and active mines, as well as, for historical mines and mining districts. One of the first projects of ADTI-MMS is to develop a handbook describing the best sampling, monitoring, predicting, mitigating, and modeling of drainage from metal mines, pit lakes and related metallurgical facilities based upon current scientific and engineering practices. One of the important aspects of planning a new mine in today's regulatory environment is the philosophy of designing a new or existing mine or expansion of operations for ultimate closure. The holistic philosophy taken in the ADTI-MMS handbook maintains that sampling and monitoring programs should be designed to take into account all aspects of the mine-life cycle. Data required for the closure of the operation are obtained throughout the mine-life cycle, from exploration through post-closure.

Real time explosive hazard information sensing, processing, and communication for autonomous operation

DOEpatents

Versteeg, Roelof J; Few, Douglas A; Kinoshita, Robert A; Johnson, Doug; Linda, Ondrej

2015-02-24

Methods, computer readable media, and apparatuses provide robotic explosive hazard detection. A robot intelligence kernel (RIK) includes a dynamic autonomy structure with two or more autonomy levels between operator intervention and robot initiative A mine sensor and processing module (ESPM) operating separately from the RIK perceives environmental variables indicative of a mine using subsurface perceptors. The ESPM processes mine information to determine a likelihood of a presence of a mine. A robot can autonomously modify behavior responsive to an indication of a detected mine. The behavior is modified between detection of mines, detailed scanning and characterization of the mine, developing mine indication parameters, and resuming detection. Real time messages are passed between the RIK and the ESPM. A combination of ESPM bound messages and RIK bound messages cause the robot platform to switch between modes including a calibration mode, the mine detection mode, and the mine characterization mode.

Real time explosive hazard information sensing, processing, and communication for autonomous operation

DOEpatents

Versteeg, Roelof J.; Few, Douglas A.; Kinoshita, Robert A.; Johnson, Douglas; Linda, Ondrej

2015-12-15

Methods, computer readable media, and apparatuses provide robotic explosive hazard detection. A robot intelligence kernel (RIK) includes a dynamic autonomy structure with two or more autonomy levels between operator intervention and robot initiative A mine sensor and processing module (ESPM) operating separately from the RIK perceives environmental variables indicative of a mine using subsurface perceptors. The ESPM processes mine information to determine a likelihood of a presence of a mine. A robot can autonomously modify behavior responsive to an indication of a detected mine. The behavior is modified between detection of mines, detailed scanning and characterization of the mine, developing mine indication parameters, and resuming detection. Real time messages are passed between the RIK and the ESPM. A combination of ESPM bound messages and RIK bound messages cause the robot platform to switch between modes including a calibration mode, the mine detection mode, and the mine characterization mode.

30 CFR 784.10 - Information collection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.10... requires applicants for permits for underground coal mines to prepare and submit an operation and...

30 CFR 740.10 - Information collection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR FEDERAL LANDS PROGRAM GENERAL REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON FEDERAL LANDS... surface coal mining operations on Federal lands. Persons intending to conduct such operations must respond...

30 CFR 740.10 - Information collection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR FEDERAL LANDS PROGRAM GENERAL REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON FEDERAL LANDS... surface coal mining operations on Federal lands. Persons intending to conduct such operations must respond...

78 FR 70067 - Notice of Availability of the Final Environmental Impact Statement for the Proposed Pan Mine...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-22

..._programs/minerals/mining_projects/pan_mine_project.html . FOR FURTHER INFORMATION CONTACT: Miles Kreidler...: Midway Gold US, Inc. (Midway) proposes to construct and operate an open-pit gold mining operation in the... years, which includes 13 years of mining and additional time for associated construction, closure, and...

75 FR 71668 - Cibota National Forest, Mount Taylor Ranger District, NM, Roca Honda Mine

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... develop and conduct underground uranium mining operations on their mining claims on and near Jesus Mesa in... open to mineral entry under the General Mining Law of 1872. Section 16 is State of New Mexico land... statement (EIS) to assess the development of a uranium mining operation on the Mount Taylor Ranger District...

30 CFR 57.22204 - Main fan operation and inspection (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main fan operation and inspection (I-A, II-A, III, and V-A mines). 57.22204 Section 57.22204 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... Main fan operation and inspection (I-A, II-A, III, and V-A mines). Main fans shall be— (a) Provided...

30 CFR 57.22204 - Main fan operation and inspection (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Main fan operation and inspection (I-A, II-A, III, and V-A mines). 57.22204 Section 57.22204 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... Main fan operation and inspection (I-A, II-A, III, and V-A mines). Main fans shall be— (a) Provided...

30 CFR 715.11 - General obligations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR INITIAL... surface coal mining and reclamation operations conducted on lands where any element of the operations is... are established by part 716 of this chapter for— (1) Surface coal mining operations on steep slopes...

30 CFR 937.700 - Oregon Federal program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Federal program. (c) The rules in this part apply to all surface coal mining operations in Oregon... more stringent environmental control and regulation of surface coal mining operations than do the... extent they provide for regulation of surface coal mining and reclamation operations which are exempt...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 75.1729 - Welding operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Welding operations. 75.1729 Section 75.1729 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1729 Welding operations. Welding...

30 CFR 939.700 - Rhode Island Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 939.700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE RHODE ISLAND § 939.700... mining and reclamation operations in Rhode Island which have been adopted under the Surface Mining...

30 CFR 941.700 - South Dakota Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 941.700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE SOUTH DAKOTA § 941.700... mining operations in South Dakota which have been adopted under the Surface Mining Control and...

30 CFR 933.700 - North Carolina Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 933.700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NORTH CAROLINA § 933.700... mining operations in North Carolina which have been adopted under the Surface Mining Control and...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operator. 71.209 Section 71.209 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Sampling Procedures § 71.209 Respirable dust samples; transmission by...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operator. 71.209 Section 71.209 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Sampling Procedures § 71.209 Respirable dust samples; transmission by...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2014 CFR

2014-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2013 CFR

2013-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operator. 71.209 Section 71.209 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Sampling Procedures § 71.209 Respirable dust samples; transmission by...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2012 CFR

2012-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2011 CFR

2011-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

30 CFR 77.1906 - Hoists; daily inspection.

Code of Federal Regulations, 2011 CFR

2011-07-01

....1906 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES... shall be run by the hoist operator through one complete cycle of operation before any person is...

MINING METHODS AND COSTS, CALYX NOS. 3 AND 8 URANIUM MINES, TEMPLE MOUNTAIN DISTRICT, EMERY COUNTY, UTAH

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dare, W.L.

1957-04-01

Descriptions are given of the Calyx No. 3 mine operated by American Reduc Uranium Corp. and Calyx No. 8 operated by Cline Co. The deposits are composed of numerous small, irregular bodies and are worked through 36 inch Calyx drill holes. The U--V ores are concentrated chiefly in the lower 30 feet of the Moss Back sandstone. In general it follows the strnta. The mine is worked by open stoping with random pillar support. The operations and mining practices of these two mines are very similar and typify the mining methods and practioes used by many small U producers onmore » the Colorado Plateau. (R.V.J.)« less

Injury experience in coal mining, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reich, R.B.; Hugler, E.C.

1994-05-01

This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1992. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries,more » summary reference tabulations are included at the end of both the operator and the contractor sections of this report.« less

Injury experience in coal mining, 1990

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1991-01-01

This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1990. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries,more » summary reference tabulations are included at the end of both the operator and the contractor sections of this report.« less

Mines in the Four Corners anticipate growth

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchsbaum, L.

2008-02-15

Productive mines in the southwest deplete reserves, while the government drags its heels on new power projects. Production in Arizona and New Mexico has fallen 18% over the last four years to 34.1 million tons. With Chevron Mining's McKinley mine rapidly depleting its reserves the industry will continue to contract. In the last three years at least three large mines in the Four Corners have terminated operations. Three others remain captive operations: BHP Billiton's San Juan Underground and Navajo Surface operations and Peabody Energy's Kayenta surface mine. In 2006 the Black Mesa mine stopped producing coal. These four mines aremore » isolated from the national railways. Peabody's new El Segundo surface mine near Grants, NM is increasing production. If the planned $3 billion Desert Rock coal-fired power plant is built this will present a new market for the Navajo mine. The article gives details about the state of the aforementioned mines and of the new King II coal mine on the northern periphery of the San Juan basin and discusses the state of plans for the Desert Rock Energy Project. 5 photos.« less

An application of data mining in district heating substations for improving energy performance

NASA Astrophysics Data System (ADS)

Xue, Puning; Zhou, Zhigang; Chen, Xin; Liu, Jing

2017-11-01

Automatic meter reading system is capable of collecting and storing a huge number of district heating (DH) data. However, the data obtained are rarely fully utilized. Data mining is a promising technology to discover potential interesting knowledge from vast data. This paper applies data mining methods to analyse the massive data for improving energy performance of DH substation. The technical approach contains three steps: data selection, cluster analysis and association rule mining (ARM). Two-heating-season data of a substation are used for case study. Cluster analysis identifies six distinct heating patterns based on the primary heat of the substation. ARM reveals that secondary pressure difference and secondary flow rate have a strong correlation. Using the discovered rules, a fault occurring in remote flow meter installed at secondary network is detected accurately. The application demonstrates that data mining techniques can effectively extrapolate potential useful knowledge to better understand substation operation strategies and improve substation energy performance.

Using MSD prevention for cultural change in mining: Queensland Government/Anglo Coal Industry partnership.

PubMed

Tilbury, Trudy; Sanderson, Liz

2012-01-01

Queensland Mining has a strong focus on safety performance, but risk management of health, including Musculoskeletal Disorders (MSDs) continues to have a lower priority. The reliance on individual screening of workers and lower level approaches such as manual handling training is part of the coal mining 'culture'. Initiatives such as the New South Wales and Queensland Mining joint project to develop good practice guidance for mining has allowed for a more consistent message on participatory ergonomics and prevention of MSD. An evidence based practice approach, including the introduction of participatory ergonomics and safe design principles, was proposed to Anglo American Coal operations in Queensland. The project consisted of a skills analysis of current health personnel, design of a facilitated participatory ergonomics training program, site visits to identify good practice and champions, and a graduated mentoring program for health personnel. Early results demonstrate a number of sites are benefiting from site taskforces with a focus on positive performance outcomes.

Data mining techniques for assisting the diagnosis of pressure ulcer development in surgical patients.

PubMed

Su, Chao-Ton; Wang, Pa-Chun; Chen, Yan-Cheng; Chen, Li-Fei

2012-08-01

Pressure ulcer is a serious problem during patient care processes. The high risk factors in the development of pressure ulcer remain unclear during long surgery. Moreover, past preventive policies are hard to implement in a busy operation room. The objective of this study is to use data mining techniques to construct the prediction model for pressure ulcers. Four data mining techniques, namely, Mahalanobis Taguchi System (MTS), Support Vector Machines (SVMs), decision tree (DT), and logistic regression (LR), are used to select the important attributes from the data to predict the incidence of pressure ulcers. Measurements of sensitivity, specificity, F(1), and g-means were used to compare the performance of four classifiers on the pressure ulcer data set. The results show that data mining techniques obtain good results in predicting the incidence of pressure ulcer. We can conclude that data mining techniques can help identify the important factors and provide a feasible model to predict pressure ulcer development.

Method for Determining the Coalbed Methane Content with Determination the Uncertainty of Measurements

NASA Astrophysics Data System (ADS)

Szlązak, Nikodem; Korzec, Marek

2016-06-01

Methane has a bad influence on safety in underground mines as it is emitted to the air during mining works. Appropriate identification of methane hazard is essential to determining methane hazard prevention methods, ventilation systems and methane drainage systems. Methane hazard is identified while roadways are driven and boreholes are drilled. Coalbed methane content is one of the parameters which is used to assess this threat. This is a requirement according to the Decree of the Minister of Economy dated 28 June 2002 on work safety and hygiene, operation and special firefighting protection in underground mines. For this purpose a new method for determining coalbed methane content in underground coal mines has been developed. This method consists of two stages - collecting samples in a mine and testing the sample in the laboratory. The stage of determining methane content in a coal sample in a laboratory is essential. This article presents the estimation of measurement uncertainty of determining methane content in a coal sample according to this methodology.

Sequential pattern data mining and visualization

DOEpatents

Wong, Pak Chung [Richland, WA; Jurrus, Elizabeth R [Kennewick, WA; Cowley, Wendy E [Benton City, WA; Foote, Harlan P [Richland, WA; Thomas, James J [Richland, WA

2011-12-06

One or more processors (22) are operated to extract a number of different event identifiers therefrom. These processors (22) are further operable to determine a number a display locations each representative of one of the different identifiers and a corresponding time. The display locations are grouped into sets each corresponding to a different one of several event sequences (330a, 330b, 330c. 330d, 330e). An output is generated corresponding to a visualization (320) of the event sequences (330a, 330b, 330c, 330d, 330e).

Sequential pattern data mining and visualization

DOEpatents

Wong, Pak Chung [Richland, WA; Jurrus, Elizabeth R [Kennewick, WA; Cowley, Wendy E [Benton City, WA; Foote, Harlan P [Richland, WA; Thomas, James J [Richland, WA

2009-05-26

One or more processors (22) are operated to extract a number of different event identifiers therefrom. These processors (22) are further operable to determine a number a display locations each representative of one of the different identifiers and a corresponding time. The display locations are grouped into sets each corresponding to a different one of several event sequences (330a, 330b, 330c. 330d, 330e). An output is generated corresponding to a visualization (320) of the event sequences (330a, 330b, 330c, 330d, 330e).

Lunar resource recovery: A definition of requirements

NASA Technical Reports Server (NTRS)

Elsworth, D.; Kohler, J. L.; Alexander, S. S.

1992-01-01

The capability to locate, mine, and process the natural resources of the Moon will be an essential requirement for lunar base development and operation. The list of materials that will be necessary is extensive and ranges from oxygen and hydrogen for fuel and life support to process tailings for emplacement over habitats. Despite the resources need, little is known about methodologies that might be suitable for utilizing lunar resources. This paper examines some of the requirements and constraints for resource recovery and identifies key areas of research needed to locate, mine, and process extraterrestrial natural resources.

Evaluation of commercial utility of ERTS-A imagery in structural reconnaissance for minerals and petroleum

NASA Technical Reports Server (NTRS)

Saunders, D. F. (Principal Investigator)

1973-01-01

The author has identified the following significant results. In areas 2 and 3 (Colorado and New Mexico - Texas) continuing correlations are observed between lineaments selected from the ERTS imagery and known fault and fracture zones. There continues to be a correlation between lineament intersectional areas and known mining areas. Initial contacts with mining and/or petroleum companies regarding the use of ERTS-1 imagery as an interpreted medium for guiding reconnaissance operations seems to indicate that the technology and economics will be commercially acceptable for initial investigatory investments.

New approach for reduction of diesel consumption by comparing different mining haulage configurations.

PubMed

Rodovalho, Edmo da Cunha; Lima, Hernani Mota; de Tomi, Giorgio

2016-05-01

The mining operations of loading and haulage have an energy source that is highly dependent on fossil fuels. In mining companies that select trucks for haulage, this input is the main component of mining costs. How can the impact of the operational aspects on the diesel consumption of haulage operations in surface mines be assessed? There are many studies relating the consumption of fuel trucks to several variables, but a methodology that prioritizes higher-impact variables under each specific condition is not available. Generic models may not apply to all operational settings presented in the mining industry. This study aims to create a method of analysis, identification, and prioritization of variables related to fuel consumption of haul trucks in open pit mines. For this purpose, statistical analysis techniques and mathematical modelling tools using multiple linear regressions will be applied. The model is shown to be suitable because the results generate a good description of the fuel consumption behaviour. In the practical application of the method, the reduction of diesel consumption reached 10%. The implementation requires no large-scale investments or very long deadlines and can be applied to mining haulage operations in other settings. Copyright © 2016 Elsevier Ltd. All rights reserved.

20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Statutory insurance requirements for coal... OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR'S INSURANCE General § 726.1 Statutory insurance requirements for coal mine...

30 CFR 77.105 - Qualified hoistman; slope or shaft sinking operation; qualifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Applications for Secretarial qualification should be submitted to the Mine Safety and Health Administration... operation; qualifications. 77.105 Section 77.105 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE...

Geomechanical Assessments of Simultaneous Operation in the Case of Transition from Open Pit to Underground Mine in Vietnam

NASA Astrophysics Data System (ADS)

Niedbalski, Zbigniew; Nguyen, Phu Minh Vuong; Widzyk-Capehart, Eleonora

2018-03-01

Nowadays, for a number of reasons, many open pit mines are considering a transition from Open Pit (OP) to Underground (UG) to remain competitive. In OP-UG transition, UG operation is operated simultaneously with the OP operation for a certain period of time. Guidelines for the simultaneous operation of OP and UG are very difficult to establish, as there are very few case studies available. Yet, because of the OP-UG interactions; the operation has a higher safety, technical and management requirements than the OP or UG methods when considered separately. In Vietnam, Cao Son is one of many OP mines, which decided to change the operational system from OP to UG. Simultaneous operation started in 2015 and will be conducted until 2030 when the OP mine Cao Son ends its mining activities. In this paper, selected geomechanical considerations of the simultaneous operation are presented. A number of numerical modelling calculations using finitedifference software with code FLAC were carried out for calibration process, slope stability analysis and the OP-UG interaction analysis for the Cao Son - Khe Cham II-IV mine. Based on the results obtained from numerical modelling, the geomechanical assessments of simultaneous operation Cao Son - Khe Cham II-IV are discussed in this paper.

Rescue complex for coal mines

NASA Astrophysics Data System (ADS)

Yungmeyster, D. A.; Urazbakhtin, R. Yu

2017-10-01

The mining industry was potentially dangerous at all times, even with the use of modern equipment in mines, accidents continue to occur, including catastrophic ones. Accidents in mines are due to the presence of specific features in the conduct of mining operations. These include the inconsistency of mining and geological conditions, the contamination of the mine atmosphere due to the release of gases from minerals, the presence of self-igniting coal strata, which creates the danger of underground fires, gas explosions. The main cause of accidents is the irresponsibility of both the manager and the personnel who violate the safety rules during mining operations.

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

43 CFR 3931.10 - Exploration plans and plans of development for mining and in situ operations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... for mining and in situ operations. 3931.10 Section 3931.10 Public Lands: Interior Regulations Relating....10 Exploration plans and plans of development for mining and in situ operations. (a) The POD must... development of the oil shale resources in the lease. (b) The operator must submit to the proper BLM office an...

43 CFR 3931.10 - Exploration plans and plans of development for mining and in situ operations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... for mining and in situ operations. 3931.10 Section 3931.10 Public Lands: Interior Regulations Relating....10 Exploration plans and plans of development for mining and in situ operations. (a) The POD must... development of the oil shale resources in the lease. (b) The operator must submit to the proper BLM office an...

43 CFR 3931.10 - Exploration plans and plans of development for mining and in situ operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... for mining and in situ operations. 3931.10 Section 3931.10 Public Lands: Interior Regulations Relating....10 Exploration plans and plans of development for mining and in situ operations. (a) The POD must... development of the oil shale resources in the lease. (b) The operator must submit to the proper BLM office an...

43 CFR 3931.10 - Exploration plans and plans of development for mining and in situ operations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... for mining and in situ operations. 3931.10 Section 3931.10 Public Lands: Interior Regulations Relating....10 Exploration plans and plans of development for mining and in situ operations. (a) The POD must... development of the oil shale resources in the lease. (b) The operator must submit to the proper BLM office an...

Application of ERTS-A imagery to fracture related mine safety hazards in the coal mining industry

NASA Technical Reports Server (NTRS)

Wier, C. E.; Wobber, F. J. (Principal Investigator)

1973-01-01

The author has identified the following significant results. The most important result to date is the demonstration of the special value of repetitive ERTS-1 multiband coverage for detecting previously unknown fracture lineaments despite the presence of a deep glacial overburden. The Illinois Basin is largely covered with glacial drift and few rock outcrops are present. A contribution to the geological understanding of Illinois and Indiana has been made. Analysis of ERTS-1 imagery has provided useful information to the State of Indiana concerning the surface mined lands. The contrast between healthy vegetation and bare ground as imaged by Band 7 is sharp and substantial detail can be obtained concerning the extent of disturbed lands, associated water bodies, large haul roads, and extent of mined lands revegetation. Preliminary results of analysis suggest a reasonable correlation between image-detected fractures and mine roof fall accidents for a few areas investigated. ERTS-1 applications to surface mining operations appear probable, but further investigations are required. The likelihood of applying ERTS-1 derived fracture data to improve coal mine safety in the entire Illinois Basin is suggested from studies conducted in Indiana.

RESEARCH TO IDENTIFY COMPONENTS OF ENERGY-RELATED WASTES: A STATE-OF-THE-ART REPORT

EPA Science Inventory

Pertinent abstracts from a survey of current (post-1976) research projects are categorized according to energy-related activity. Subjects include coal strip mines, oil refineries, oil shale operations, coal-fired power plants, geothermal energy production, coal liquefaction plant...

Sampling and monitoring for closure

USGS Publications Warehouse

McLemore, Virginia T.; Smith, Kathleen S.; Russell, Carol C.

2007-01-01

An important aspect of planning a new mine or mine expansion within the modern regulatory framework is to design for ultimate closure. Sampling and monitoring for closure is a form of environmental risk management. By implementing a sampling and monitoring program early in the life of the mining operation, major costs can be avoided or minimized. The costs for treating mine drainage in perpetuity are staggering, especially if they are unanticipated. The Metal Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS), a cooperative government-industry-academia organization, was established to address drainage-quality technologies of metal mining and metallurgical operations. ADTI-MMS recommends that sampling and monitoring programs consider the entire mine-life cycle and that data needed for closure of an operation be collected from exploration through postclosure.

20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Statutory insurance requirements for coal..., DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR'S INSURANCE General § 726.1 Statutory insurance requirements for coal mine...

20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 20 Employees' Benefits 4 2012-04-01 2012-04-01 false Statutory insurance requirements for coal..., DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR'S INSURANCE General § 726.1 Statutory insurance requirements for coal mine...

20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 20 Employees' Benefits 4 2013-04-01 2013-04-01 false Statutory insurance requirements for coal..., DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR'S INSURANCE General § 726.1 Statutory insurance requirements for coal mine...

20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 20 Employees' Benefits 4 2014-04-01 2014-04-01 false Statutory insurance requirements for coal..., DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR'S INSURANCE General § 726.1 Statutory insurance requirements for coal mine...

40 CFR 372.23 - SIC and NAICS codes to which this Part applies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... facilities primarily engaged in reproducing text, drawings, plans, maps, or other copy, by blueprinting...)); 212324Kaolin and Ball Clay Mining Limited to facilities operating without a mine or quarry and that are...)); 212393Other Chemical and Fertilizer Mineral Mining Limited to facilities operating without a mine or quarry...

30 CFR 77.1500 - Auger mining; planning.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auger mining; planning. 77.1500 Section 77.1500... § 77.1500 Auger mining; planning. Auger mining shall be planned and conducted by the operator to insure against any hazard to underground workings located at or near such auger operations and all auger holes...

Distributed communications and control network for robotic mining

NASA Technical Reports Server (NTRS)

Schiffbauer, William H.

1989-01-01

The application of robotics to coal mining machines is one approach pursued to increase productivity while providing enhanced safety for the coal miner. Toward that end, a network composed of microcontrollers, computers, expert systems, real time operating systems, and a variety of program languages are being integrated that will act as the backbone for intelligent machine operation. Actual mining machines, including a few customized ones, have been given telerobotic semiautonomous capabilities by applying the described network. Control devices, intelligent sensors and computers onboard these machines are showing promise of achieving improved mining productivity and safety benefits. Current research using these machines involves navigation, multiple machine interaction, machine diagnostics, mineral detection, and graphical machine representation. Guidance sensors and systems employed include: sonar, laser rangers, gyroscopes, magnetometers, clinometers, and accelerometers. Information on the network of hardware/software and its implementation on mining machines are presented. Anticipated coal production operations using the network are discussed. A parallelism is also drawn between the direction of present day underground coal mining research to how the lunar soil (regolith) may be mined. A conceptual lunar mining operation that employs a distributed communication and control network is detailed.

Capturing coupled riparian and coastal disturbance from industrial mining using cloud-resilient satellite time series analysis.

PubMed

Alonzo, Michael; Van Den Hoek, Jamon; Ahmed, Nabil

2016-10-11

The socio-ecological impacts of large scale resource extraction are frequently underreported in underdeveloped regions. The open-pit Grasberg mine in Papua, Indonesia, is one of the world's largest copper and gold extraction operations. Grasberg mine tailings are discharged into the lowland Ajkwa River deposition area (ADA) leading to forest inundation and degradation of water bodies critical to indigenous peoples. The extent of the changes and temporal linkages with mining activities are difficult to establish given restricted access to the region and persistent cloud cover. Here, we introduce remote sensing methods to "peer through" atmospheric contamination using a dense Landsat time series to simultaneously quantify forest loss and increases in estuarial suspended particulate matter (SPM) concentration. We identified 138 km 2 of forest loss between 1987 and 2014, an area >42 times larger than the mine itself. Between 1987 and 1998, the rate of disturbance was highly correlated (Pearson's r = 0.96) with mining activity. Following mine expansion and levee construction along the ADA in the mid-1990s, we recorded significantly (p < 0.05) higher SPM in the Ajkwa Estuary compared to neighboring estuaries. This research provides a means to quantify multiple modes of ecological damage from mine waste disposal or other disturbance events.

Capturing coupled riparian and coastal disturbance from industrial mining using cloud-resilient satellite time series analysis

PubMed Central

Alonzo, Michael; Van Den Hoek, Jamon; Ahmed, Nabil

2016-01-01

The socio-ecological impacts of large scale resource extraction are frequently underreported in underdeveloped regions. The open-pit Grasberg mine in Papua, Indonesia, is one of the world’s largest copper and gold extraction operations. Grasberg mine tailings are discharged into the lowland Ajkwa River deposition area (ADA) leading to forest inundation and degradation of water bodies critical to indigenous peoples. The extent of the changes and temporal linkages with mining activities are difficult to establish given restricted access to the region and persistent cloud cover. Here, we introduce remote sensing methods to “peer through” atmospheric contamination using a dense Landsat time series to simultaneously quantify forest loss and increases in estuarial suspended particulate matter (SPM) concentration. We identified 138 km2 of forest loss between 1987 and 2014, an area >42 times larger than the mine itself. Between 1987 and 1998, the rate of disturbance was highly correlated (Pearson’s r = 0.96) with mining activity. Following mine expansion and levee construction along the ADA in the mid-1990s, we recorded significantly (p < 0.05) higher SPM in the Ajkwa Estuary compared to neighboring estuaries. This research provides a means to quantify multiple modes of ecological damage from mine waste disposal or other disturbance events. PMID:27725748

Capturing coupled riparian and coastal disturbance from industrial mining using cloud-resilient satellite time series analysis

NASA Astrophysics Data System (ADS)

Alonzo, Michael; van den Hoek, Jamon; Ahmed, Nabil

2016-10-01

The socio-ecological impacts of large scale resource extraction are frequently underreported in underdeveloped regions. The open-pit Grasberg mine in Papua, Indonesia, is one of the world’s largest copper and gold extraction operations. Grasberg mine tailings are discharged into the lowland Ajkwa River deposition area (ADA) leading to forest inundation and degradation of water bodies critical to indigenous peoples. The extent of the changes and temporal linkages with mining activities are difficult to establish given restricted access to the region and persistent cloud cover. Here, we introduce remote sensing methods to “peer through” atmospheric contamination using a dense Landsat time series to simultaneously quantify forest loss and increases in estuarial suspended particulate matter (SPM) concentration. We identified 138 km2 of forest loss between 1987 and 2014, an area >42 times larger than the mine itself. Between 1987 and 1998, the rate of disturbance was highly correlated (Pearson’s r = 0.96) with mining activity. Following mine expansion and levee construction along the ADA in the mid-1990s, we recorded significantly (p < 0.05) higher SPM in the Ajkwa Estuary compared to neighboring estuaries. This research provides a means to quantify multiple modes of ecological damage from mine waste disposal or other disturbance events.

25 CFR 216.4 - Technical examination of prospective surface exploration and mining operations.

Code of Federal Regulations, 2013 CFR

2013-04-01

... mining sites and mining operations vary widely with respect to topography, climate, surrounding land uses... quality below standards established by the appropriate State water pollution control agency, or by the...

25 CFR 216.4 - Technical examination of prospective surface exploration and mining operations.

Code of Federal Regulations, 2014 CFR

2014-04-01

... mining sites and mining operations vary widely with respect to topography, climate, surrounding land uses... quality below standards established by the appropriate State water pollution control agency, or by the...

25 CFR 216.4 - Technical examination of prospective surface exploration and mining operations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... mining sites and mining operations vary widely with respect to topography, climate, surrounding land uses... quality below standards established by the appropriate State water pollution control agency, or by the...

25 CFR 216.4 - Technical examination of prospective surface exploration and mining operations.

Code of Federal Regulations, 2012 CFR

2012-04-01

... mining sites and mining operations vary widely with respect to topography, climate, surrounding land uses... quality below standards established by the appropriate State water pollution control agency, or by the...

43 CFR 20.402 - Interests in underground or surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 1 2012-10-01 2011-10-01 true Interests in underground or surface coal... Certain Employees of the Department § 20.402 Interests in underground or surface coal mining operations... coal mining operations means ownership or part ownership by an employee of lands, stocks, bonds...

43 CFR 20.402 - Interests in underground or surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 1 2011-10-01 2011-10-01 false Interests in underground or surface coal... Certain Employees of the Department § 20.402 Interests in underground or surface coal mining operations... coal mining operations means ownership or part ownership by an employee of lands, stocks, bonds...

43 CFR 20.402 - Interests in underground or surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Interests in underground or surface coal... Certain Employees of the Department § 20.402 Interests in underground or surface coal mining operations... coal mining operations means ownership or part ownership by an employee of lands, stocks, bonds...

Analysis of Mining Terrain Deformation Characteristics with Deformation Information System

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Milczarek, Wojciech; Grzempowski, Piotr

2014-05-01

Mapping and prediction of mining related deformations of the earth surface is an important measure for minimising threat to surface infrastructure, human population, the environment and safety of the mining operation itself arising from underground extraction of useful minerals. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and increasing with the development of geographical information technologies. These include for example: terrestrial geodetic measurements, global positioning systems, remote sensing, spatial interpolation, finite element method modelling, GIS based modelling, geological modelling, empirical modelling using the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The aim of this paper is to introduce the concept of an integrated Deformation Information System (DIS) developed in geographic information systems environment for analysis and modelling of various spatial data related to mining activity and demonstrate its applications for mapping and visualising, as well as identifying possible mining terrain deformation areas with various spatial modelling methods. The DIS concept is based on connected modules that include: the spatial database - the core of the system, the spatial data collection module formed by: terrestrial, satellite and remote sensing measurements of the ground changes, the spatial data mining module for data discovery and extraction, the geological modelling module, the spatial data modeling module with data processing algorithms for spatio-temporal analysis and mapping of mining deformations and their characteristics (e.g. deformation parameters: tilt, curvature and horizontal strain), the multivariate spatial data classification module and the visualization module allowing two-dimensional interactive and static mapping and three-dimensional visualizations of mining ground characteristics. The Systems's functionality has been presented on the case study of a coal mining region in SW Poland where it has been applied to study characteristics and map mining induced ground deformations in a city in the last two decades of underground coal extraction and in the first decade after the end of mining. The mining subsidence area and its deformation parameters (tilt and curvature) have been calculated and the latter classified and mapped according to the Polish regulations. In addition possible areas of ground deformation have been indicated based on multivariate spatial data analysis of geological and mining operation characteristics with the geographically weighted regression method.

Environmental considerations related to mining of nonfuel minerals

USGS Publications Warehouse

Seal, Robert R.; Piatak, Nadine M.; Kimball, Bryn E.; Hammarstrom, Jane M.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Throughout most of human history, environmental stewardship during mining has not been a priority partly because of the lack of applicable laws and regulations and partly because of ignorance about the effects that mining can have on the environment. In the United States, the National Environmental Policy Act of 1969, in conjunction with related laws, codified a more modern approach to mining, including the responsibility for environmental stewardship, and provided a framework for incorporating environmental protection into mine planning. Today, similar frameworks are in place in the other developed countries of the world, and international mining companies generally follow similar procedures wherever they work in the world. The regulatory guidance has fostered an international effort among all stakeholders to identify best practices for environmental stewardship.The modern approach to mining using best practices involves the following: (a) establishment of a pre-mining baseline from which to monitor environmental effects during mining and help establish geologically reasonable closure goals; (b) identification of environmental risks related to mining through standardized approaches; and (c) formulation of an environmental closure plan before the start of mining. A key aspect of identifying the environmental risks and mitigating those risks is understanding how the risks vary from one deposit type to another—a concept that forms the basis for geoenvironmental mineral-deposit models.Accompanying the quest for best practices is the goal of making mining sustainable into the future. Sustainable mine development is generally considered to be development that meets the needs of the present generation without compromising the ability of future generations to meet their own needs. The concept extends beyond the availability of nonrenewable mineral commodities and includes the environmental and social effects of mine development.Global population growth, meanwhile, has decreased the percentage of inhabitable land available to support society’s material needs. Presently, the land area available to supply the mineral resources, energy resources, water, food, shelter, and waste disposal needs of all Earth’s inhabitants is estimated to be 135 square meters per person. Continued global population growth will only increase the challenges of sustainable mining.Current trends in mining are also expected to lead to new environmental challenges in the future, among which are mine-waste management issues related to mining larger deposits for lower ore grade; water-management issues related to both the mining of larger deposits and the changes in precipitation brought about by climate change; and greenhouse gas issues related to reducing the carbon footprint of larger, more energy-intensive mining operations.

Groundwater quality at the Saline Valley Conservancy District well field, Gallatin County, Illinois

USGS Publications Warehouse

Gorczynska, Magdalena; Kay, Robert T.

2016-08-29

The Saline Valley Conservancy District (SVCD) operates wells that supply water to most of the water users in Saline and Gallatin Counties, Illinois. The SVCD wells draw water from a shallow sand and gravel aquifer located in close proximity to an abandoned underground coal mine, several abandoned oil wells, and at least one operational oil well. The aquifer that yields water to the SVCD wells overlies the New Albany Shale, which may be subjected to shale-gas exploration by use of hydraulic fracturing. The SVCD has sought technical assistance from the U.S. Geological Survey to characterize baseline water quality at the SVCD well field so that future changes in water quality (if any) and the cause of those changes (including mine leachate and hydraulic fracturing) can be identified.

77 FR 22608 - Notice of Intent To Prepare an Environmental Impact Statement for the Proposed Bald Mountain Mine...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-16

... normal business hours. SUPPLEMENTARY INFORMATION: Bald Mountain Mine (BMM), owned by Barrick Gold US Inc... Statement for the Proposed Bald Mountain Mine North and South Operations Area Projects, White Pine County.... ADDRESSES: You may submit comments related to the Bald Mountain Mine North and South Operations Area...

COMPARISON OF DATA FROM SYNTHETIC LEACHATE AND DIRECT SAMPLING OF ACID DRAINAGE FROM MINE WASTES: IMPLICATIONS FOR MERCURY TRANSPORT AND WASTE MANAGEMENT

EPA Science Inventory

The Sulphur Bank Mercury Mine (SBMM) in Lake County, California operated from the 1860s through the 1950's. Mining for sulfur started with surface operations and progressed to shaft, then open pit techniques to obtain mercury. Mining has resulted in deposition of approximately ...

77 FR 62266 - Proposed Extension of Existing Information Collection; Daily Inspection of Surface Coal Mines...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-12

... conducting an on shift examination for hazardous conditions, mine operators better ensure a safe working environment for the miners and a reduction in accidents. II. Desired Focus of Comments The Mine Safety and... (30 CFR 77.1713) requires coal mine operators to conduct examinations of each active working area of...

77 FR 15026 - Privacy Act of 1974; Farm Records File (Automated) System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-14

... Mining Project, all program data collected and handled by either RMA or FSA will be treated with the full... data warehouse and data mining operation. RMA will use the information to search or ``mine'' existing... fraud, waste, and abuse. The data mining operation is authorized by the Agricultural Risk Protection Act...

A Review of Mine Rescue Ensembles for Underground Coal Mining in the United States.

PubMed

Kilinc, F Selcen; Monaghan, William D; Powell, Jeffrey B

The mining industry is among the top ten industries nationwide with high occupational injury and fatality rates, and mine rescue response may be considered one of the most hazardous activities in mining operations. In the aftermath of an underground mine fire, explosion or water inundation, specially equipped and trained teams have been sent underground to fight fires, rescue entrapped miners, test atmospheric conditions, investigate the causes of the disaster, or recover the dead. Special personal protective ensembles are used by the team members to improve the protection of rescuers against the hazards of mine rescue and recovery. Personal protective ensembles used by mine rescue teams consist of helmet, cap lamp, hood, gloves, protective clothing, boots, kneepads, facemask, breathing apparatus, belt, and suspenders. While improved technology such as wireless warning and communication systems, lifeline pulleys, and lighted vests have been developed for mine rescuers over the last 100 years, recent research in this area of personal protective ensembles has been minimal due to the trending of reduced exposure of rescue workers. In recent years, the exposure of mine rescue teams to hazardous situations has been changing. However, it is vital that members of the teams have the capability and proper protection to immediately respond to a wide range of hazardous situations. Currently, there are no minimum requirements, best practice documents, or nationally recognized consensus standards for protective clothing used by mine rescue teams in the United States (U.S.). The following review provides a summary of potential issues that can be addressed by rescue teams and industry to improve potential exposures to rescue team members should a disaster situation occur. However, the continued trending in the mining industry toward non-exposure to potential hazards for rescue workers should continue to be the primary goal. To assist in continuing this trend, the mining industry and regulatory agencies have been more restrictive by requiring additional post disaster information regarding atmospheric conditions and other hazards before exposing rescue workers and others in the aftermath of a mine disaster. In light of some of the more recent mine rescuer fatalities such as the Crandall Canyon Mine and Jim Walters Resources in the past years, the direction of reducing exposure is preferred. This review provides a historical perspective on ensembles used during mine rescue operations and summarizes environmental hazards, critical elements of mine rescue ensembles, and key problems with these elements. This study also identifies domains for improved mine rescue ensembles. Furthermore, field observations from several coal mine rescue teams were added to provide the information on the currently used mine rescue ensembles in the U.S.

A Review of Mine Rescue Ensembles for Underground Coal Mining in the United States

PubMed Central

Kilinc, F. Selcen; Monaghan, William D.; Powell, Jeffrey B.

2016-01-01

The mining industry is among the top ten industries nationwide with high occupational injury and fatality rates, and mine rescue response may be considered one of the most hazardous activities in mining operations. In the aftermath of an underground mine fire, explosion or water inundation, specially equipped and trained teams have been sent underground to fight fires, rescue entrapped miners, test atmospheric conditions, investigate the causes of the disaster, or recover the dead. Special personal protective ensembles are used by the team members to improve the protection of rescuers against the hazards of mine rescue and recovery. Personal protective ensembles used by mine rescue teams consist of helmet, cap lamp, hood, gloves, protective clothing, boots, kneepads, facemask, breathing apparatus, belt, and suspenders. While improved technology such as wireless warning and communication systems, lifeline pulleys, and lighted vests have been developed for mine rescuers over the last 100 years, recent research in this area of personal protective ensembles has been minimal due to the trending of reduced exposure of rescue workers. In recent years, the exposure of mine rescue teams to hazardous situations has been changing. However, it is vital that members of the teams have the capability and proper protection to immediately respond to a wide range of hazardous situations. Currently, there are no minimum requirements, best practice documents, or nationally recognized consensus standards for protective clothing used by mine rescue teams in the United States (U.S.). The following review provides a summary of potential issues that can be addressed by rescue teams and industry to improve potential exposures to rescue team members should a disaster situation occur. However, the continued trending in the mining industry toward non-exposure to potential hazards for rescue workers should continue to be the primary goal. To assist in continuing this trend, the mining industry and regulatory agencies have been more restrictive by requiring additional post disaster information regarding atmospheric conditions and other hazards before exposing rescue workers and others in the aftermath of a mine disaster. In light of some of the more recent mine rescuer fatalities such as the Crandall Canyon Mine and Jim Walters Resources in the past years, the direction of reducing exposure is preferred. This review provides a historical perspective on ensembles used during mine rescue operations and summarizes environmental hazards, critical elements of mine rescue ensembles, and key problems with these elements. This study also identifies domains for improved mine rescue ensembles. Furthermore, field observations from several coal mine rescue teams were added to provide the information on the currently used mine rescue ensembles in the U.S. PMID:27065231

30 CFR 701.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR GENERAL PERMANENT... program implementation; (2) Subchapter D on surface coal mining and reclamation operations on Federal lands; (3) Subchapter E on surface coal mining and reclamation operations on Indian lands. (4...

30 CFR 701.4 - Responsibility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR GENERAL PERMANENT... responsibility for regulation of coal exploration and surface coal mining and reclamation operations during the... mining and reclamation operations, approval of coal exploration which substantially disturbs the natural...

30 CFR 75.156 - AMS operator, qualifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... training on duties and responsibilities at each mine where an AMS operator is employed in accordance with the mine operator's approved Part 48 training plan. (b) An AMS operator must be able to demonstrate to...

30 CFR 77.1712 - Reopening mines; notification; inspection prior to mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

... to mining. 77.1712 Section 77.1712 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... prior to mining. Prior to reopening any surface coal mine after it has been abandoned or declared... an authorized representative of the Secretary before any mining operations in such mine are...

30 CFR 77.1712 - Reopening mines; notification; inspection prior to mining.

Code of Federal Regulations, 2011 CFR

2011-07-01

... to mining. 77.1712 Section 77.1712 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... prior to mining. Prior to reopening any surface coal mine after it has been abandoned or declared... an authorized representative of the Secretary before any mining operations in such mine are...

Lead exposure from soil in Peruvian mining towns: a national assessment supported by two contrasting examples

PubMed Central

Bravo, Carolina; Gil, Vladimir; Sherpa, Shaky; Jack, Darby

2012-01-01

Abstract Objective To estimate the population of Peru living in the vicinity of active or former mining operations that could be exposed to lead from contaminated soil. Methods Geographic coordinates were compiled for 113 active mines, 138 ore processing plants and 3 smelters, as well as 7743 former mining sites. The population living within 5 km of these sites was calculated from census data for 2000. In addition, the lead content of soil in the historic mining town of Cerro de Pasco and around a recent mine and ore processing plant near the city of Huaral was mapped in 2009 using a hand-held X-ray fluorescence analyser. Findings Spatial analysis indicated that 1.6 million people in Peru could be living within 5 km of an active or former mining operation. Two thirds of the population potentially exposed was accounted for by 29 clusters of mining operations, each with a population of over 10 000 each. These clusters included 112 active and 3438 former mining operations. Soil lead levels exceeded 1200 mg/kg, a reference standard for residential soil, in 35 of 74 sites tested in Cerro de Pasco but in only 4 of 47 sites tested around the newer operations near Huaral. Conclusion Soil contamination with lead is likely to be extensive in Peruvian mining towns but the level of contamination is spatially far from uniform. Childhood exposure by soil ingestion could be substantially reduced by mapping soil lead levels, making this information public and encouraging local communities to isolate contaminated areas from children. PMID:23284193

Lead exposure from soil in Peruvian mining towns: a national assessment supported by two contrasting examples.

PubMed

van Geen, Alexander; Bravo, Carolina; Gil, Vladimir; Sherpa, Shaky; Jack, Darby

2012-12-01

To estimate the population of Peru living in the vicinity of active or former mining operations that could be exposed to lead from contaminated soil. Geographic coordinates were compiled for 113 active mines, 138 ore processing plants and 3 smelters, as well as 7743 former mining sites. The population living within 5 km of these sites was calculated from census data for 2000. In addition, the lead content of soil in the historic mining town of Cerro de Pasco and around a recent mine and ore processing plant near the city of Huaral was mapped in 2009 using a hand-held X-ray fluorescence analyser. Spatial analysis indicated that 1.6 million people in Peru could be living within 5 km of an active or former mining operation. Two thirds of the population potentially exposed was accounted for by 29 clusters of mining operations, each with a population of over 10 000 each. These clusters included 112 active and 3438 former mining operations. Soil lead levels exceeded 1200 mg/kg, a reference standard for residential soil, in 35 of 74 sites tested in Cerro de Pasco but in only 4 of 47 sites tested around the newer operations near Huaral. Soil contamination with lead is likely to be extensive in Peruvian mining towns but the level of contamination is spatially far from uniform. Childhood exposure by soil ingestion could be substantially reduced by mapping soil lead levels, making this information public and encouraging local communities to isolate contaminated areas from children.

25 CFR 215.11 - New leases where prior leases have been forfeited or abandoned.

Code of Federal Regulations, 2011 CFR

2011-04-01

... MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.11 New leases where prior leases... zinc ores have been discovered but the mines and mining operations have been abandoned and the leases... to the highest bidder. If the lead and zinc mining lease on said land be offered for sale at public...

SEASONAL VARIATIONS OF DISSOLVED MERCURY CONCENTRATIONS AT THE SULPHUR BANK MERCURY MINE, CLEAR LAKE, CALIFORNIA: IMPLICATIONS FOR MINE DRAINAGE MONITORING

EPA Science Inventory

The Sulphur Bank Mercury Mine in Lake County, California (SBMM) was operated from the 1860s through the 1950s. Mining for sulfur started with surface operations and then progressed to shaft and later open pit techniques to obtain mercury. SBMM is located adjacent to the shore o...

30 CFR 761.15 - Procedures for waiving the prohibition on surface coal mining operations within the buffer zone...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Procedures for waiving the prohibition on surface coal mining operations within the buffer zone of an occupied dwelling. 761.15 Section 761.15... surface coal mining operations within the buffer zone of an occupied dwelling. (a) This section does not...

30 CFR 761.15 - Procedures for waiving the prohibition on surface coal mining operations within the buffer zone...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Procedures for waiving the prohibition on surface coal mining operations within the buffer zone of an occupied dwelling. 761.15 Section 761.15... surface coal mining operations within the buffer zone of an occupied dwelling. (a) This section does not...

30 CFR 761.15 - Procedures for waiving the prohibition on surface coal mining operations within the buffer zone...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Procedures for waiving the prohibition on surface coal mining operations within the buffer zone of an occupied dwelling. 761.15 Section 761.15... surface coal mining operations within the buffer zone of an occupied dwelling. (a) This section does not...

30 CFR 761.15 - Procedures for waiving the prohibition on surface coal mining operations within the buffer zone...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Procedures for waiving the prohibition on surface coal mining operations within the buffer zone of an occupied dwelling. 761.15 Section 761.15... surface coal mining operations within the buffer zone of an occupied dwelling. (a) This section does not...

30 CFR 761.15 - Procedures for waiving the prohibition on surface coal mining operations within the buffer zone...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Procedures for waiving the prohibition on surface coal mining operations within the buffer zone of an occupied dwelling. 761.15 Section 761.15... surface coal mining operations within the buffer zone of an occupied dwelling. (a) This section does not...

30 CFR 761.13 - Procedures for compatibility findings for surface coal mining operations on Federal lands in...

Code of Federal Regulations, 2011 CFR

2011-07-01

... surface coal mining operations on Federal lands in national forests. 761.13 Section 761.13 Mineral... surface coal mining operations on Federal lands in national forests. (a) If you intend to rely upon the... national forest, you must request that we obtain the Secretarial findings required by § 761.11(b). (b) You...

30 CFR 761.13 - Procedures for compatibility findings for surface coal mining operations on Federal lands in...

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface coal mining operations on Federal lands in national forests. 761.13 Section 761.13 Mineral... surface coal mining operations on Federal lands in national forests. (a) If you intend to rely upon the... national forest, you must request that we obtain the Secretarial findings required by § 761.11(b). (b) You...

30 CFR 761.13 - Procedures for compatibility findings for surface coal mining operations on Federal lands in...

Code of Federal Regulations, 2014 CFR

2014-07-01

... surface coal mining operations on Federal lands in national forests. 761.13 Section 761.13 Mineral... surface coal mining operations on Federal lands in national forests. (a) If you intend to rely upon the... national forest, you must request that we obtain the Secretarial findings required by § 761.11(b). (b) You...

30 CFR 761.13 - Procedures for compatibility findings for surface coal mining operations on Federal lands in...

Code of Federal Regulations, 2012 CFR

2012-07-01

... surface coal mining operations on Federal lands in national forests. 761.13 Section 761.13 Mineral... surface coal mining operations on Federal lands in national forests. (a) If you intend to rely upon the... national forest, you must request that we obtain the Secretarial findings required by § 761.11(b). (b) You...

30 CFR 761.13 - Procedures for compatibility findings for surface coal mining operations on Federal lands in...

Code of Federal Regulations, 2010 CFR

2010-07-01

... surface coal mining operations on Federal lands in national forests. 761.13 Section 761.13 Mineral... surface coal mining operations on Federal lands in national forests. (a) If you intend to rely upon the... national forest, you must request that we obtain the Secretarial findings required by § 761.11(b). (b) You...

Underground coal mine instrumentation and test

NASA Technical Reports Server (NTRS)

Burchill, R. F.; Waldron, W. D.

1976-01-01

The need to evaluate mechanical performance of mine tools and to obtain test performance data from candidate systems dictate that an engineering data recording system be built. Because of the wide range of test parameters which would be evaluated, a general purpose data gathering system was designed and assembled to permit maximum versatility. A primary objective of this program was to provide a specific operating evaluation of a longwall mining machine vibration response under normal operating conditions. A number of mines were visited and a candidate for test evaluation was selected, based upon management cooperation, machine suitability, and mine conditions. Actual mine testing took place in a West Virginia mine.

Method of operator safety assessment for underground mobile mining equipment

NASA Astrophysics Data System (ADS)

Działak, Paulina; Karliński, Jacek; Rusiński, Eugeniusz

2018-01-01

The paper presents a method of assessing the safety of operators of mobile mining equipment (MME), which is adapted to current and future geological and mining conditions. The authors focused on underground mines, with special consideration of copper mines (KGHM). As extraction reaches into deeper layers of the deposit it can activate natural hazards, which, thus far, have been considered unusual and whose range and intensity are different depending on the field of operation. One of the main hazards that affect work safety and can become the main barrier in the exploitation of deposits at greater depths is climate threat. The authors have analysed the phenomena which may impact the safety of MME operators, with consideration of accidents that have not yet been studied and are not covered by the current safety standards for this group of miners. An attempt was made to develop a method for assessing the safety of MME operators, which takes into account the mentioned natural hazards and which is adapted to current and future environmental conditions in underground mines.

30 CFR 740.11 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... jurisdiction. (e) This subchapter shall not apply to surface coal mining and reclamation operations within a... Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR FEDERAL LANDS PROGRAM GENERAL REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON FEDERAL LANDS § 740.11...

30 CFR 900.4 - Responsibilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE INTRODUCTION § 900.4 Responsibilities. (a) Each State that has surface coal mining and reclamation operations or coal exploration activities on non...

30 CFR 800.14 - Determination of bond amount.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 800.14 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR BONDING AND INSURANCE REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS BOND AND INSURANCE REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS UNDER REGULATORY PROGRAMS § 800.14...

30 CFR 735.1 - Scope.

Code of Federal Regulations, 2014 CFR

2014-07-01

... State programs for the regulation and control of surface coal mining and reclamation operations; (b) Administer and enforce State programs for the regulation and control of surface coal mining and reclamation operations; and (c) Administer cooperative agreements for State regulation of surface coal mining and...

30 CFR 735.1 - Scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... State programs for the regulation and control of surface coal mining and reclamation operations; (b) Administer and enforce State programs for the regulation and control of surface coal mining and reclamation operations; and (c) Administer cooperative agreements for State regulation of surface coal mining and...

30 CFR 735.1 - Scope.

Code of Federal Regulations, 2013 CFR

2013-07-01

... State programs for the regulation and control of surface coal mining and reclamation operations; (b) Administer and enforce State programs for the regulation and control of surface coal mining and reclamation operations; and (c) Administer cooperative agreements for State regulation of surface coal mining and...

30 CFR 75.1716-1 - Operations under water; notification by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... § 75.1716-1 Operations under water; notification by operator. An operator planning to mine coal from... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operations under water; notification by..., and in such manner that mining operations will be conducted, or tunnels constructed, under any river...

30 CFR 49.50 - Certification of coal mine rescue teams.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Certification of coal mine rescue teams. 49.50... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.50 Certification of coal mine... coal mine, the mine operator shall send the District Manager an annual statement certifying that each...

30 CFR 49.50 - Certification of coal mine rescue teams.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Certification of coal mine rescue teams. 49.50... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.50 Certification of coal mine... coal mine, the mine operator shall send the District Manager an annual statement certifying that each...

30 CFR 49.50 - Certification of coal mine rescue teams.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Certification of coal mine rescue teams. 49.50... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.50 Certification of coal mine... coal mine, the mine operator shall send the District Manager an annual statement certifying that each...

30 CFR 49.20 - Requirements for all coal mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Requirements for all coal mines. 49.20 Section... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.20 Requirements for all coal mines. (a) The operator of each underground coal mine shall make available two certified mine rescue...

30 CFR 49.20 - Requirements for all coal mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Requirements for all coal mines. 49.20 Section... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.20 Requirements for all coal mines. (a) The operator of each underground coal mine shall make available two certified mine rescue...

30 CFR 49.50 - Certification of coal mine rescue teams.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Certification of coal mine rescue teams. 49.50... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.50 Certification of coal mine... coal mine, the mine operator shall send the District Manager an annual statement certifying that each...

30 CFR 49.20 - Requirements for all coal mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Requirements for all coal mines. 49.20 Section... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.20 Requirements for all coal mines. (a) The operator of each underground coal mine shall make available two certified mine rescue...

30 CFR 49.20 - Requirements for all coal mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Requirements for all coal mines. 49.20 Section... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.20 Requirements for all coal mines. (a) The operator of each underground coal mine shall make available two certified mine rescue...

30 CFR 49.50 - Certification of coal mine rescue teams.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Certification of coal mine rescue teams. 49.50... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.50 Certification of coal mine... coal mine, the mine operator shall send the District Manager an annual statement certifying that each...

30 CFR 49.20 - Requirements for all coal mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Requirements for all coal mines. 49.20 Section... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.20 Requirements for all coal mines. (a) The operator of each underground coal mine shall make available two certified mine rescue...

Idaho and Montana non-fuel exploration database 1980-1997

USGS Publications Warehouse

Buckingham, David A.; DiFrancesco, Carl A.; Porter, Kenneth E.; Bleiwas, Donald I.; Causey, J. Douglas; Ferguson, William B.

2006-01-01

This report describes a relational database containing information about mineral exploration projects in the States of Idaho and Montana for the years 1980 through 1997 and a spatial (geographic) database constructed using data from the relational database. The focus of this project was to collect information on exploration for mineral commodities with the exception of sand, gravel, coal, geothermal, oil, and gas. The associate databases supplied with this report are prototypes that can be used or modified as needed. The following sources were used to create the databases-serial mining periodicals; annual mineral publications; mining company reports; U.S. Bureau of Mines (USBM) and U.S. Geological Survey (USGS) publications; an Idaho mineral property data base developed by Dave Boleneus, USGS, Spokane, Washington; Montana state publications; and discussions with representatives of Montana, principally the Montana Bureau of Mines and Geology and the Department of Environmental Quality. Fifty commodity groups were reported between the 596 exploration projects identified in this study. Precious metals (gold, silver, or platinum group elements) were the primary targets for about 67 percent of the exploration projects. Information on 17 of the projects did not include commodities. No location could be determined for 51 projects, all in Idaho. During the time period evaluated, some mineral properties were developed into large mining operations (for example Beal Mountain Mine, Stillwater Mine, Troy Mine, Montana Tunnels Mine) and six properties were reclaimed. Environmental Impact Statements were done on four properties. Some operating mines either closed or went through one or more shutdowns and re-openings. Other properties, where significant resources were delineated by recent exploration during this time frame, await the outcome of important factors for development such as defining additional reserves, higher metal prices, and the permitting process. Many of these projects examined relatively minor mineral occurrences. Approximately half of the exploration projects are located on Federal lands and about 40 percent were on lands managed by the U.S. Forest Service. More than 75 percent of the exploration occurred in areas with significant previous mineral activity.

Porites corals as recorders of mining and environmental impacts: Misima Island, Papua New Guinea

NASA Astrophysics Data System (ADS)

Fallon, Stewart J.; White, Jamie C.; McCulloch, Malcolm T.

2002-01-01

In 1989 open-cut gold mining commenced on Misima Island in Papua New Guinea (PNG). Open-cut mining by its nature causes a significant increase in sedimentation via the exposure of soils to the erosive forces of rain and runoff. This increased sedimentation affected the nearby fringing coral reef to varying degrees, ranging from coral mortality (smothering) to relatively minor short-term impacts. The sediment associated with the mining operation consists of weathered quartz feldspar, greenstone, and schist. These rocks have distinct chemical characteristics (rare earth element patterns and high abundances of manganese, zinc, and lead) and are entering the near-shore environment in considerably higher than normal concentrations. Using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), we analyzed eight colonies (two from high sedimentation, two transitional, two minor, and two unaffected control sites) for Y, La, Ce, Mn, Zn, and Pb. All sites show low steady background levels prior to the commencement of mining in 1988. Subsequently, all sites apart from the control show dramatic increases of Y, La, and Ce associated with the increased sedimentation as well as rapid decreases following the cessation of mining. The elements Zn and Pb exhibit a different behavior, increasing in concentration after 1989 when ore processing began and one year after initial mining operations. Elevated levels of Zn and Pb in corals has continued well after the cessation of mining, indicating ongoing transport into the reef of these metals via sulfate-rich waters. Rare earth element (REE) abundance patterns measured in two corals show significant differences compared to Coral Sea seawater. The corals display enrichments in the light and middle REEs while the heavy REEs are depleted relative to the seawater pattern. This suggests that the nearshore seawater REE pattern is dominated by island sedimentation. Trace element abundances of Misima Island corals clearly record the dramatic changes in the environmental conditions at this site and provide a basis for identifying anthropogenic influences on corals reefs.

Orapa Diamond Mine, Botswana

NASA Image and Video Library

2015-11-16

This image from NASA Terra spacecraft shows the Orapa diamond mine, the world largest diamond mine by area. The mine is located in Botswana. It is the oldest of four mines operated by the same company, having begun operations in 1971. Orapa is an open pit style of mine, located on two kimberlite pipes. Currently, the Orapa mine annually produces approximately 11 million carats (2200 kg) of diamonds. The Letlhakane diamond mine is also an open pit construction. In 2003, the Letlhakane mine produced 1.06 million carats of diamonds. The Damtshaa diamond mine is the newest of four mines, located on top of four distinct kimberlite pipes of varying ore grade. The mine is forecast to produce about 5 million carats of diamond over the projected 31 year life of the mine. The image was acquired October 5, 2014, covers an area of 28 by 45 km, and is located at 21.3 degrees south, 25.4 degrees east. http://photojournal.jpl.nasa.gov/catalog/PIA20104

Citation-related reliability analysis for a pilot sample of underground coal mines.

PubMed

Kinilakodi, Harisha; Grayson, R Larry

2011-05-01

The scrutiny of underground coal mine safety was heightened because of the disasters that occurred in 2006-2007, and more recently in 2010. In the aftermath of the 2006 incidents, the U.S. Congress passed the Mine Improvement and New Emergency Response Act of 2006 (MINER Act), which strengthened the existing regulations and mandated new laws to address various issues related to emergency preparedness and response, escape from an emergency situation, and protection of miners. The National Mining Association-sponsored Mine Safety Technology and Training Commission study highlighted the role of risk management in identifying and controlling major hazards, which are elements that could come together and cause a mine disaster. In 2007 MSHA revised its approach to the "Pattern of Violations" (POV) process in order to target unsafe mines and then force them to remediate conditions in their mines. The POV approach has certain limitations that make it difficult for it to be enforced. One very understandable way to focus on removing threats from major-hazard conditions is to use citation-related reliability analysis. The citation reliability approach, which focuses on the probability of not getting a citation on a given inspector day, is considered an analogue to the maintenance reliability approach, which many mine operators understand and use. In this study, the citation reliability approach was applied to a stratified random sample of 31 underground coal mines to examine its potential for broader application. The results clearly show the best-performing and worst-performing mines for compliance with mine safety standards, and they highlight differences among different mine sizes. Copyright © 2010 Elsevier Ltd. All rights reserved.

Indirect estimation of emission factors for phosphate surface mining using air dispersion modeling.

PubMed

Tartakovsky, Dmitry; Stern, Eli; Broday, David M

2016-06-15

To date, phosphate surface mining suffers from lack of reliable emission factors. Due to complete absence of data to derive emissions factors, we developed a methodology for estimating them indirectly by studying a range of possible emission factors for surface phosphate mining operations and comparing AERMOD calculated concentrations to concentrations measured around the mine. We applied this approach for the Khneifiss phosphate mine, Syria, and the Al-Hassa and Al-Abyad phosphate mines, Jordan. The work accounts for numerous model unknowns and parameter uncertainties by applying prudent assumptions concerning the parameter values. Our results suggest that the net mining operations (bulldozing, grading and dragline) contribute rather little to ambient TSP concentrations in comparison to phosphate processing and transport. Based on our results, the common practice of deriving the emission rates for phosphate mining operations from the US EPA emission factors for surface coal mining or from the default emission factor of the EEA seems to be reasonable. Yet, since multiple factors affect dispersion from surface phosphate mines, a range of emission factors, rather than only a single value, was found to satisfy the model performance. Copyright © 2016 Elsevier B.V. All rights reserved.

Microcomputer keeps watch at Emerald Mine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-04-01

This paper reviews the computerized mine monitoring system set up at the Emerald Mine, SW Pennsylvania, USA. This coal mine has pioneered the automation of many production and safety features and this article covers their work in fire detection and conveyor belt monitoring. A central computer control room can safely watch over the whole underground mining operation using one 25 inch colour monitor. These new data-acquisition systems will lead the way, in the future, to safer move efficient coal mining. Multi-point monitoring of carbon monoxide, heat anomalies, toxic gases and the procedures in conveyor belt operation from start-up to closedown.

Memorandum of Understanding on Surface Coal Mining Operations Resulting in Placement of Excess Spoil Fills in the Waters of the United States

EPA Pesticide Factsheets

MOU on Surface Coal Mining Operations establishes a process for improving coordination in the review of permit applications required for surface coal mining and reclamation in waters of the United States

Finalizing the Libby Action Plan Research Program

EPA Science Inventory

Libby, Montana is the location of a former vermiculite mine that operated from 1923 to 1990. The vermiculite ore from the mine co-existed with amphibole asbestos, referred to as Libby Amphibole Asbestos (LAA). Combined with the cessation of the asbestos mining and processing oper...

30 CFR 75.382 - Mechanical escape facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

....382 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.382 Mechanical escape... shall be run through one complete cycle of operation to determine that it is operating properly. (d) A...

Geochemical Characteristics of TP3 Mine Wastes at the Elizabeth Copper Mine Superfund Site, Orange County, Vermont

USGS Publications Warehouse

Hammarstrom, Jane M.; Piatak, Nadine M.; Seal, Robert R.; Briggs, Paul H.; Meier, Allen L.; Muzik, Timothy L.

2003-01-01

Remediation of the Elizabeth mine Superfund site in the Vermont copper belt poses challenges for balancing environmental restoration goals with issues of historic preservation while adopting cost-effective strategies for site cleanup and long-term maintenance. The waste-rock pile known as TP3, at the headwaters of Copperas Brook, is especially noteworthy in this regard because it is the worst source of surface- and ground-water contamination identified to date, while also being the area of greatest historical significance. The U.S. Geological Survey (USGS) conducted a study of the historic mine-waste piles known as TP3 at the Elizabeth mine Superfund site near South Strafford, Orange County, VT. TP3 is a 12.3-acre (49,780 m2) subarea of the Elizabeth mine site. It is a focus area for historic preservation because it encompasses an early 19th century copperas works as well as waste from late 19th- and 20th century copper mining (Kierstead, 2001). Surface runoff and seeps from TP3 form the headwaters of Copperas Brook. The stream flows down a valley onto flotation tailings from 20th century copper mining operations and enters the West Branch of the Ompompanoosuc River approximately 1 kilometer downstream from the mine site. Shallow drinking water wells down gradient from TP3 exceed drinking water standards for copper and cadmium (Hathaway and others, 2001). The Elizabeth mine was listed as a Superfund site in 2001, mainly because of impacts of acid-mine drainage on the Ompompanoosuc River.

78 FR 79010 - Criteria to Certify Coal Mine Rescue Teams

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... to Certify Coal Mine Rescue Teams AGENCY: Mine Safety and Health Administration, Labor. ACTION... updated the coal mine rescue team certification criteria. The Mine Improvement and New Emergency Response... mine operator to certify the qualifications of a coal mine rescue team is that team members are...

30 CFR 49.15 - Mine rescue station.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Mine rescue station. 49.15 Section 49.15 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.15 Mine rescue station. (a) Every operator...

30 CFR 49.15 - Mine rescue station.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Mine rescue station. 49.15 Section 49.15 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.15 Mine rescue station. (a) Every operator...

30 CFR 49.15 - Mine rescue station.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Mine rescue station. 49.15 Section 49.15 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.15 Mine rescue station. (a) Every operator...

30 CFR 49.15 - Mine rescue station.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Mine rescue station. 49.15 Section 49.15 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.15 Mine rescue station. (a) Every operator...

30 CFR 49.15 - Mine rescue station.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Mine rescue station. 49.15 Section 49.15 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.15 Mine rescue station. (a) Every operator...

GENERAL EXTERIOR VIEW, LOOKING NORTHEAST, OF THE SURFACE PLANT WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

GENERAL EXTERIOR VIEW, LOOKING NORTHEAST, OF THE SURFACE PLANT WITH CONVEYORS. JIM WALTER RESOURCES INC. MINING DIVISION OPERATES FOUR UNDERGROUND COAL MINES IN THE BLUE CREEK COAL FIELD OF BIRMINGHAM DISTRICT, THREE IN TUSCALOOSA COUNTY AND ONE IN JEFFERSON COUNTY. TOTAL ANNUAL PRODUCTION IS 8,000,000 TONS. AT 2,300 DEEP, JIM WALTER'S BROOKWOOD MINES ARE THE DEEPEST UNDERGROUND COAL MINES IN NORTH AMERICA. THEY PRODUCE A HIGH-GRADE MEDIUM VOLATILE LOW SULPHUR METALLURGICAL COAL. THE BROOKWOOD NO. 5 MINE (PICTURED IN THIS PHOTOGRAPH) EMPLOYS THE LONGWALL MINING TECHNIQUES WITH BELTS CONVEYING COAL FROM UNDERGROUND OPERATIONS TO THE SURFACE. - JIm Walter Resources, Incorporated, Brookwood No. 5 Mine, 12972 Lock 17 Road, Brookwood, Tuscaloosa County, AL

30 CFR 773.14 - Eligibility for provisionally issued permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... 773.14 Section 773.14 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION... surface coal mining and reclamation operation with— (1) A notice of violation issued under § 843.12 of...

25 CFR 213.40 - Cancellations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... FIVE CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.40 Cancellations. (a) When, in the opinion... or of the applicable regulations, or if mining operations are conducted wastefully and without regard to good mining practice, the Secretary of the Interior shall have the right at any time after 30 days...

30 CFR 912.700 - Idaho Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE IDAHO § 912.700 Idaho Federal program. (a) This part contains all rules that are applicable to surface coal mining operations in Idaho...

30 CFR 905.700 - California Federal Program.

Code of Federal Regulations, 2010 CFR

2010-07-01

....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE CALIFORNIA § 905.700 California Federal Program. (a) This part contains all rules that are applicable to surface coal mining operations in...

30 CFR 947.700 - Washington Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE WASHINGTON § 947.700 Washington Federal program. (a) This part contains all rules that are applicable to surface coal mining operations in...

30 CFR 922.700 - Michigan Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE MICHIGAN § 922.700 Michigan Federal program. (a) This part contains all rules that are applicable to surface coal mining operations in...

30 CFR 910.700 - Georgia Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE GEORGIA § 910.700 Georgia Federal program. (a) This part contains all rules that are applicable to surface coal mining operations in Georgia...

30 CFR 937.700 - Oregon Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.700 Oregon Federal program. (a) This part contains all rules that are applicable to surface coal mining operations in Oregon...

30 CFR 942.700 - Tennessee Federal program.

Code of Federal Regulations, 2010 CFR

2010-07-01

....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE TENNESSEE § 942.700 Tennessee Federal program. (a) This part contains all rules that are applicable to surface coal mining operations in...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 56.12040 - Installation of operating controls.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Installation of operating controls. 56.12040 Section 56.12040 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity...

30 CFR 70.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operator. 70.209 Section 70.209 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Sampling Procedures... Laboratory, Pittsburgh Safety and Health Technology Center, Cochran Mill Road, Building 38, P.O. Box 18179...

30 CFR 70.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operator. 70.209 Section 70.209 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Sampling Procedures... Laboratory, Pittsburgh Safety and Health Technology Center, Cochran Mill Road, Building 38, P.O. Box 18179...

30 CFR 70.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operator. 70.209 Section 70.209 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Sampling Procedures... Laboratory, Pittsburgh Safety and Health Technology Center, Cochran Mill Road, Building 38, P.O. Box 18179...

30 CFR 57.4362 - Underground rescue and firefighting operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Fire Prevention and Control Firefighting Procedures/alarms/drills § 57.4362 Underground rescue and firefighting operations. Following evacuation of a mine in a fire emergency, only persons wearing and trained...

20 CFR 726.2 - Purpose and scope of this part.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 726.2 Employees' Benefits OFFICE OF WORKERS' COMPENSATION PROGRAMS, DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR... and controlling the circumstances under which a coal mine operator shall fulfill his insurance...

20 CFR 726.2 - Purpose and scope of this part.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 726.2 Employees' Benefits OFFICE OF WORKERS' COMPENSATION PROGRAMS, DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR... and controlling the circumstances under which a coal mine operator shall fulfill his insurance...

20 CFR 726.2 - Purpose and scope of this part.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 726.2 Employees' Benefits OFFICE OF WORKERS' COMPENSATION PROGRAMS, DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR COAL MINE OPERATOR... and controlling the circumstances under which a coal mine operator shall fulfill his insurance...

78 FR 40494 - Renewal of Approved Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-05

... that assists the BLM in managing operations authorized by the mining laws, in preventing unnecessary or... Mining Law (43 CFR subpart 3809). Forms: Form 3809-1, Surface Management Surety Bond; Form 3809-2... enables the BLM to determine whether operators and mining claimants are meeting their responsibility...

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport.

PubMed

Shahan, M R; Seaman, C E; Beck, T W; Colinet, J F; Mischler, S E

2017-09-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8.

Injury Surveillance and Safety Considerations for Large-Format Lead-Acid Batteries Used in Mining Applications.

PubMed

Reyes, Miguel Angel; Novak, Thomas

2016-03-01

Large lead-acid batteries are predominantly used throughout the mining industry to power haulage, utility, and personnel-carrier vehicles. Without proper operation and maintenance, the use of these batteries can introduce mechanical and electrical hazards, particularly in the confined, and potentially dangerous, environment of an underground coal mine. A review of the Mine Safety and Health Administration accident/illness/injury database reveals that a significant number of injuries occur during the maintenance and repair of lead-acid batteries. These injuries include burns from electrical arcing and acid exposure, as well as strained muscles and crushed hands. The National Institute for Occupational Safety and Health investigated the design and implementation of these batteries to identify safety interventions that can mitigate these inherent hazards. This paper promotes practical design modifications, such as reducing the size and weight of battery assembly lids in conjunction with lift assists, as well as using five-pole cable connectors to improve safety.

Injury Surveillance and Safety Considerations for Large-Format Lead-Acid Batteries Used in Mining Applications

PubMed Central

Reyes, Miguel Angel; Novak, Thomas

2016-01-01

Large lead-acid batteries are predominantly used throughout the mining industry to power haulage, utility, and personnel-carrier vehicles. Without proper operation and maintenance, the use of these batteries can introduce mechanical and electrical hazards, particularly in the confined, and potentially dangerous, environment of an underground coal mine. A review of the Mine Safety and Health Administration accident/illness/injury database reveals that a significant number of injuries occur during the maintenance and repair of lead-acid batteries. These injuries include burns from electrical arcing and acid exposure, as well as strained muscles and crushed hands. The National Institute for Occupational Safety and Health investigated the design and implementation of these batteries to identify safety interventions that can mitigate these inherent hazards. This paper promotes practical design modifications, such as reducing the size and weight of battery assembly lids in conjunction with lift assists, as well as using five-pole cable connectors to improve safety. PMID:27784953

Spiced-up ANFO mixture leads to super blasts for casting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chironis, N.P.

1984-05-01

There is one problem common to many coal operators in the mountainous regions of western Pennsylvania. As coal seams nearer the crop lines of their mine sites are removed, the overburden heights and stripping ratios increase to about 20-to-1, the range where coal becomes uneconomical to mine. Faced with this situation, a mine operator usually pursues one of four options: 1. Drive a drift mine, which means switching to underground operations with all the complexity and costs involved; 2. Purchase a larger dragline, which involves huge capital expenditures; 3. Bring in an augering machine to auger the exposed seams, amore » technique effective only for a very limited distance into the highwalls; 4. Discontinue operations, the route most operators take.« less

Improving machine operation management efficiency via improving the vehicle park structure and using the production operation information database

NASA Astrophysics Data System (ADS)

Koptev, V. Yu

2017-02-01

The work represents the results of studying basic interconnected criteria of separate equipment units of the transport network machines fleet, depending on production and mining factors to improve the transport systems management. Justifying the selection of a control system necessitates employing new methodologies and models, augmented with stability and transport flow criteria, accounting for mining work development dynamics on mining sites. A necessary condition is the accounting of technical and operating parameters related to vehicle operation. Modern open pit mining dispatching systems must include such kinds of the information database. An algorithm forming a machine fleet is presented based on multi-variation task solution in connection with defining reasonable operating features of a machine working as a part of a complex. Proposals cited in the work may apply to mining machines (drilling equipment, excavators) and construction equipment (bulldozers, cranes, pile-drivers), city transport and other types of production activities using machine fleet.

To build a mine: Prospect to product

NASA Technical Reports Server (NTRS)

Gertsch, Richard E.

1992-01-01

The terrestrial definition of ore is a quantity of earth materials containing a mineral that can be extracted at a profit. While a space-based resource-gathering operation may well be driven by other motives, such an operation should have the most favorable cost-benefit ratio possible. To this end, principles and procedures already tested by the stringent requirements of the profit motive should guide the selection, design, construction, and operation of a space-based mine. Proceeding from project initiation to a fully operational mine requires several interacting and overlapping steps, which are designed to facilitate the decision process and insure economic viability. The steps to achieve a fully operational mine are outlined. Presuming that the approach to developing nonterrestrial resources will parallel that for developing mineral resources on Earth, we can speculate on some of the problems associated with developing lunar and asteroidal resources. The baseline for our study group was a small lunar mine and oxygen extraction facility. The development of this facility is described in accordance with the steps outlined.

30 CFR 48.22 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... surface mine, including any delivery, office, or scientific worker or occasional, short-term maintenance... construction, or who is regularly exposed to mine hazards, or who is a maintenance or service worker employed by the operator or a maintenance or service worker contracted by the operator to work at the mine for...

30 CFR 48.22 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... surface mine, including any delivery, office, or scientific worker or occasional, short-term maintenance... construction, or who is regularly exposed to mine hazards, or who is a maintenance or service worker employed by the operator or a maintenance or service worker contracted by the operator to work at the mine for...

30 CFR 48.22 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface mine, including any delivery, office, or scientific worker or occasional, short-term maintenance... construction, or who is regularly exposed to mine hazards, or who is a maintenance or service worker employed by the operator or a maintenance or service worker contracted by the operator to work at the mine for...

30 CFR 48.22 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... surface mine, including any delivery, office, or scientific worker or occasional, short-term maintenance... construction, or who is regularly exposed to mine hazards, or who is a maintenance or service worker employed by the operator or a maintenance or service worker contracted by the operator to work at the mine for...

78 FR 40496 - Notice of availability of the Final Environmental Impact Statement for the Proposed Hollister...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-05

... silver mining operation. Most of the infrastructure to support a mining operation was authorized and.... The Proposed Action consists of underground mining, constructing a new production shaft, improving.... Public comments resulted in the addition of clarifying text, but did not significantly change the...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2012 CFR

2012-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Withdrawal from operation of the mining...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2014 CFR

2014-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Withdrawal from operation of the mining...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2013 CFR

2013-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Withdrawal from operation of the mining...

43 CFR 3823.4 - Withdrawal from operation of the mining laws.

Code of Federal Regulations, 2011 CFR

2011-10-01

... MINING LAWS Prospecting, Mineral Locations, and Mineral Patents Within National Forest Wilderness § 3823... valid rights then existing, the minerals in lands within National Forest Wilderness are withdrawn from... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Withdrawal from operation of the mining...

Applying WEPP technologies to western alkaline surface coal mines

Treesearch

J. Q. Wu; S. Dun; H. Rhee; X. Liu; W. J. Elliot; T. Golnar; J. R. Frankenberger; D. C. Flanagan; P. W. Conrad; R. L. McNearny

2011-01-01

One aspect of planning surface mining operations, regulated by the National Pollutant Discharge Elimination System (NPDES), is estimating potential environmental impacts during mining operations and the reclamation period that follows. Practical computer simulation tools are effective for evaluating site-specific sediment control and reclamation plans for the NPDES....

Utilizing hydrologic, statistical, and geochemical tools to assess uranium mobility in surface and near-surface environments

NASA Astrophysics Data System (ADS)

Naftz, D. L.; Walton-Day, K. E.; Fuller, C.; Dam, W. L.; Briggs, M. A.; Snyder, T.

2015-12-01

Legacy uranium (U) mining and processing activities have resulted in soil and water contamination on Federal, state, and tribal lands in the western United States. Sites include legacy mill sites associated with U extraction now managed by the Department of Energy and thousands of waste dumps associated with U exploration, mining, and processing. Recently (2012), over 400,000 hectares of federally managed land in northern Arizona was withdrawn from consideration of mining for a 20-year period to protect the Grand Canyon watershed from potentially adverse effects of U mineral exploration and development. Ore from active and recently active U mines in the Colorado Plateau, the Henry Mountains Complex, and the Arizona Strip is transported to the only currently (2015) active conventional mill site in the western United States, located in Utah. Previous and ongoing U.S. Geological Survey assessments to examine U mobility at a variety of legacy and active sites associated with ore exploration, extraction, and processing will be presented as field-scale examples. Topics associated with site investigations will include: (1) offsite migration of radionuclides associated with the operation of the White Mesa U mill; (2) long-term contaminant transport from legacy U waste dumps on Bureau of Land Management regulated land in Utah; (3) application of incremental soil sampling techniques to determine pre- and post-mining radionuclide levels associated with planned and operating U mines in northern Arizona; (4) application of fiber optic digital temperature sensing equipment to identify areas where shallow groundwater containing elevated U levels may be discharging to a river adjacent to a reclaimed mill site in central Wyoming; and (5) field-scale manipulation of groundwater chemistry to limit U migration from a legacy upgrader site in southeastern Utah.

Air quality impact assessment of multiple open pit coal mines in northern Colombia.

PubMed

Huertas, José I; Huertas, María E; Izquierdo, Sebastián; González, Enrique D

2012-01-01

The coal mining region in northern Colombia is one of the largest open pit mining regions of the world. In 2009, there were 8 mining companies in operation with an approximate coal production of ∼70 Mtons/year. Since 2007, the Colombian air quality monitoring network has reported readings that exceed the daily and annual air quality standards for total suspended particulate (TSP) matter and particles with an equivalent aerodynamic diameter smaller than 10 μm (PM₁₀) in nearby villages. This paper describes work carried out in order to establish an appropriate clean air program for this region, based on the Colombian national environmental authority requirement for modeling of TSP and PM(10) dispersion. A TSP and PM₁₀ emission inventory was initially developed, and topographic and meteorological information for the region was collected and analyzed. Using this information, the dispersion of TSP was modeled in ISC3 and AERMOD using meteorological data collected by 3 local stations during 2008 and 2009. The results obtained were compared to actual values measured by the air quality monitoring network. High correlation coefficients (>0.73) were obtained, indicating that the models accurately described the main factors affecting particle dispersion in the region. The model was then used to forecast concentrations of particulate matter for 2010. Based on results from the model, areas within the modeling region were identified as highly, fairly, moderately and marginally polluted according to local regulations. Additionally, the contribution particulate matter to the pollution at each village was estimated. Using these predicted values, the Colombian environmental authority imposed new decontamination measures on the mining companies operating in the region. These measures included the relocation of three villages financed by the mine companies based on forecasted pollution levels. Copyright © 2011. Published by Elsevier Ltd.

PREVENTION OF ACID MINE DRAINAGE GENERATION FROM OPEN-PIT MINE HIGHWALLS

EPA Science Inventory

Exposed, open pit mine highwalls contribute significantly to the production of acid mine

drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Available information on the generation of AMD from open-pit mine highwalls is very limit...

30 CFR 49.3 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Metal and... miners willing to serve on a mine rescue team; (8) The operator's alternative plan for assuring that a...

30 CFR 49.3 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Metal and... miners willing to serve on a mine rescue team; (8) The operator's alternative plan for assuring that a...

30 CFR 49.3 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Metal and... miners willing to serve on a mine rescue team; (8) The operator's alternative plan for assuring that a...

Distribution of 226Ra body burden of workers in an underground uranium mine in India.

PubMed

Patnaik, R L; Jha, V N; Kumar, R; Srivastava, V S; Ravi, P M; Tripathi, R M

2014-11-01

Uranium mine workers are exposed to ore dust containing uranium and its daughter products during different mining operations. These radionuclides may pose inhalation hazards to workers during the course of their occupation. The most significant among these radionuclides is (226)Ra. The measurement of radium body burden of uranium mine workers is important to assess their internal exposure. For this purpose, the radon-in-breath measurement technique has been used in the present paper. Workers at the Jaduguda mine, India, associated with different categories of mining operations were monitored between 2001 and 2007. The measurement results indicate that workers--depending on mining operation category--show (226)Ra body burdens ranging from 0.15 to 2.85 kBq. The maximum body burden was found for workers associated with timbering operations, with an average (226)Ra body burden of 0.85 ± 0.54 kBq. Overall, the average value observed for 800 workers was 0.76 ± 0.51 kBq, which gives rise to an average effective dose of 1.67 mSv per year for inhalation and 0.21 mSv per year for ingestion.

Assessment of respirable dust exposures in an opencast coal mine.

PubMed

Onder, M; Yigit, E

2009-05-01

All major opencast mining activities produce dust. The major operations that produce dust are drilling, blasting, loading, unloading, and transporting. Dust not only deteriorates the environmental air quality in and around the mining site but also creates serious health hazards. Therefore, assessment of dust levels that arise from various opencast mining operations is required to prevent and minimize the health risks. To achieve this objective, an opencast coal mining area was selected to generate site-specific emission data and collect respirable dust measurement samples. The study covered various mining activities in different locations including overburden loading, stock yard, coal loading, drilling, and coal handling plant. The dust levels were examined to assess miners' exposure to respirable dust in each of the opencast mining areas from 1994 to 2005. The data obtained from the dust measurement studies were evaluated by using analysis of variance (ANOVA) and the Tukey-Kramer procedure. The analyses were performed by using Minitab 14 statistical software. It was concluded that, drilling operations produce higher dust concentration levels and thus, drill operators may have higher incidence of respiratory disorders related to exposure to dust in their work environment.

A study of unstable rock failures using finite difference and discrete element methods

NASA Astrophysics Data System (ADS)

Garvey, Ryan J.

Case histories in mining have long described pillars or faces of rock failing violently with an accompanying rapid ejection of debris and broken material into the working areas of the mine. These unstable failures have resulted in large losses of life and collapses of entire mine panels. Modern mining operations take significant steps to reduce the likelihood of unstable failure, however eliminating their occurrence is difficult in practice. Researchers over several decades have supplemented studies of unstable failures through the application of various numerical methods. The direction of the current research is to extend these methods and to develop improved numerical tools with which to study unstable failures in underground mining layouts. An extensive study is first conducted on the expression of unstable failure in discrete element and finite difference methods. Simulated uniaxial compressive strength tests are run on brittle rock specimens. Stable or unstable loading conditions are applied onto the brittle specimens by a pair of elastic platens with ranging stiffnesses. Determinations of instability are established through stress and strain histories taken for the specimen and the system. Additional numerical tools are then developed for the finite difference method to analyze unstable failure in larger mine models. Instability identifiers are established for assessing the locations and relative magnitudes of unstable failure through measures of rapid dynamic motion. An energy balance is developed which calculates the excess energy released as a result of unstable equilibria in rock systems. These tools are validated through uniaxial and triaxial compressive strength tests and are extended to models of coal pillars and a simplified mining layout. The results of the finite difference simulations reveal that the instability identifiers and excess energy calculations provide a generalized methodology for assessing unstable failures within potentially complex mine models. These combined numerical tools may be applied in future studies to design primary and secondary supports in bump-prone conditions, evaluate retreat mining cut sequences, asses pillar de-stressing techniques, or perform backanalyses on unstable failures in select mining layouts.

30 CFR 780.4 - Responsibilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.4...

30 CFR 784.4 - Responsibilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.4...

30 CFR 784.29 - Diversions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.29...

30 CFR 784.2 - Objectives.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.2...

36 CFR 5.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Prospecting, mining, and... OF THE INTERIOR COMMERCIAL AND PRIVATE OPERATIONS § 5.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the...

30 CFR 49.11 - Purpose and scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... TEAMS Mine Rescue Teams for Underground Coal Mines § 49.11 Purpose and scope. (a) This subpart... recovery. (b) The following Table 49.11 summarizes the new requirements for mine rescue teams contained in... Operators and Mine Rescue Teams Requirement Type of mine rescue team Mine-site Composite Contract State...

30 CFR 49.11 - Purpose and scope.

Code of Federal Regulations, 2011 CFR

2011-07-01

... TEAMS Mine Rescue Teams for Underground Coal Mines § 49.11 Purpose and scope. (a) This subpart... recovery. (b) The following Table 49.11 summarizes the new requirements for mine rescue teams contained in... Operators and Mine Rescue Teams Requirement Type of mine rescue team Mine-site Composite Contract State...

30 CFR 49.11 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... TEAMS Mine Rescue Teams for Underground Coal Mines § 49.11 Purpose and scope. (a) This subpart... recovery. (b) The following Table 49.11 summarizes the new requirements for mine rescue teams contained in... Operators and Mine Rescue Teams Requirement Type of mine rescue team Mine-site Composite Contract State...

30 CFR 49.11 - Purpose and scope.

Code of Federal Regulations, 2014 CFR

2014-07-01

... TEAMS Mine Rescue Teams for Underground Coal Mines § 49.11 Purpose and scope. (a) This subpart... recovery. (b) The following Table 49.11 summarizes the new requirements for mine rescue teams contained in... Operators and Mine Rescue Teams Requirement Type of mine rescue team Mine-site Composite Contract State...

30 CFR 49.11 - Purpose and scope.

Code of Federal Regulations, 2013 CFR

2013-07-01

... TEAMS Mine Rescue Teams for Underground Coal Mines § 49.11 Purpose and scope. (a) This subpart... recovery. (b) The following Table 49.11 summarizes the new requirements for mine rescue teams contained in... Operators and Mine Rescue Teams Requirement Type of mine rescue team Mine-site Composite Contract State...

30 CFR 780.27 - Reclamation plan: Surface mining near underground mining.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Reclamation plan: Surface mining near underground mining. 780.27 Section 780.27 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL...

Mining drives extensive deforestation in the Brazilian Amazon.

PubMed

Sonter, Laura J; Herrera, Diego; Barrett, Damian J; Galford, Gillian L; Moran, Chris J; Soares-Filho, Britaldo S

2017-10-18

Mining poses significant and potentially underestimated risks to tropical forests worldwide. In Brazil's Amazon, mining drives deforestation far beyond operational lease boundaries, yet the full extent of these impacts is unknown and thus neglected in environmental licensing. Here we quantify mining-induced deforestation and investigate the aspects of mining operations, which most likely contribute. We find mining significantly increased Amazon forest loss up to 70 km beyond mining lease boundaries, causing 11,670 km 2 of deforestation between 2005 and 2015. This extent represents 9% of all Amazon forest loss during this time and 12 times more deforestation than occurred within mining leases alone. Pathways leading to such impacts include mining infrastructure establishment, urban expansion to support a growing workforce, and development of mineral commodity supply chains. Mining-induced deforestation is not unique to Brazil; to mitigate adverse impacts of mining and conserve tropical forests globally, environmental assessments and licensing must considered both on- and off-lease sources of deforestation.

Taxation and regulation of uranium mining in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1990-11-01

Government taxation and regulation have a profound influence on mineral operations. In Canada, taxation occurs both on the federal and provincial levels. In addition, both federal and provincial regulations also affect mine operations, sometimes with overlapping, or conflicting, legislation and jurisdiction. Three broad areas of regulation affect the mine production of uranium in Canada: (1) mining law or mineral rights; (2) the licensing procedures; and (3) regulation of occupational health and safety.

In Brief: Coal mining regulations

NASA Astrophysics Data System (ADS)

Showstack, Randy

2009-12-01

The U.S. Department of the Interior (DOI) announced on 18 November measures to strengthen the oversight of state surface coal mining programs and to promulgate federal regulations to protect streams affected by surface coal mining operations. DOI's Office of Surface Mining Reclamation and Enforcement (OSM) is publishing an advance notice of a proposed rule about protecting streams from adverse impacts of surface coal mining operations. A rule issued by the Bush administration in December 2008 allows coal mine operators to place excess excavated materials into streams if they can show it is not reasonably possible to avoid doing so. “We are moving as quickly as possible under the law to gather public input for a new rule, based on sound science, that will govern how companies handle fill removed from mountaintop coal seams,” according to Wilma Lewis, assistant secretary for Land and Minerals Management at DOI.

Potential minability and economic viability of the Antaramut-Kurtan-Dzoragukh coal field, north-central Armenia; a prefeasibility study

USGS Publications Warehouse

Huber, Douglas W.; Pierce, Brenda S.

2000-01-01

The U. S. Geological Survey (USGS) conducted a coal resource assessment of several areas in Armenia from 1997 to 1999. This report, which presents a prefeasibility study of the economic and mining potential of one coal deposit found and studied by the USGS team, was prepared using all data available at the time of the study and the results of the USGS exploratory work, including core drilling, trenching, coal quality analyses, and other ongoing field work. On the basis of information currently available, it is the authors? opinion that a small surface coal mine having about a 20-year life span could be developed in the Antaramut-Kurtan-Dzoragukh coal field, specifically at the Dzoragukh site. The mining organization selected or created to establish the mine will need to conduct necessary development drilling and other work to establish the final feasibility study for the mine. The company will need to be entrepreneurial, profit oriented, and sensitive to the coal consumer; have an analytical management staff; and focus on employee training, safety, and protection of the environment. It is anticipated that any interested parties will be required to submit detailed mining plans to the appropriate Armenian Government agencies. Further development work will be required to reach a final decision regarding the economic feasibility of the mine. However, available information indicates that a small, economic surface mine can be developed at this locality. The small mine suggested is a typical surface-outcropstripping, contour mining operation. In addition, auger mining is strongly suggested, because the recovery of these low-cost mining reserves will help to ensure that the operation will be a viable, economic enterprise. (Auger mining is a system in which large-diameter boreholes are placed horizontally into the coal seam at the final highwall set as the economic limit for the surface mining operation). A special horizontal boring machine, which can be imported from Russia, is required for auger mining. Although auger-mining coal reserves do exist, the necessary development work will further verify the extent of these reserves and all of the other indicated reserves. The following items are based on the detailed study reported in this publication. Initial investment.?Following an investment of US $85,000 over a 12-month period in mine development drilling and other activities, a decision must be taken regarding further investment in an ongoing mining operation. If the new data support the opening of the surface mine, __________________________ 1Consultant, 6024 Morning Dew Drive, Austin, TX 78749. 2 U.S. Geological Survey, 956 National Center, Reston, VA 20192 1 2 MINABILITY AND ECONOMIC VIABILITY, ANTARAMUT-KURTAN-DZORAGUKH COAL FIELD the $85,000 development cost is amortized over the first 10 years of mine production. If the new data do not support the opening of the mine, the $85,000 is considered a business development expense that may be written off against profits from other operations for income or other tax purposes or simply as a business loss. Total capital required.?The equipment costs will reach a total of $900,500 which will be amortized over a 7-year period to establish estimated coal mining costs. Estimated working capital costs are $300,000, which will be borrowed. Surface mining reserves.?Approximately 840,200 metric tonnes of surface minable coal reserves at 9.3 m3 of overburden per metric tonne of minable coal is indicated. Recovery of the minable coal at 85 percent will yield 714,000 recoverable metric tonnes of marketable as-mined coal. Auger mining reserves.?Auger-mining reserves of 576,000 metric tonnes are indicated. Recoverable auger-mining reserves of 202,000 metric tonnes (at 35-percent recovery) can be expected. Auger-mining production will vary according to the hole size being used, but, in either case, augering is a very profitable addition to the mining oper

Off-road truck-related accidents in U.S. mines

PubMed Central

Dindarloo, Saeid R.; Pollard, Jonisha P.; Siami-Irdemoosa, Elnaz

2016-01-01

Introduction Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. Methods A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Results Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5 years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. Conclusions The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Practical application Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. PMID:27620937

Off-road truck-related accidents in U.S. mines.

PubMed

Dindarloo, Saeid R; Pollard, Jonisha P; Siami-Irdemoosa, Elnaz

2016-09-01

Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. Copyright © 2016 Elsevier Ltd and National Safety Council. All rights reserved.

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

30 CFR 77.408 - Welding operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Welding operations. 77.408 Section 77.408 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... for Mechanical Equipment § 77.408 Welding operations. Welding operations shall be shielded and the...

Characterizing the hydrological system in Rosia Montana mining area (Romania) for AMD mitigation

NASA Astrophysics Data System (ADS)

Cozma, Alexandra; Baciu, Calin; Olenici, Adriana; Brahaita, Dorian; Pop, Cristian; Lazar, Laura; Roba, Carmen; Popita, Gabriela

2015-04-01

Keywords: mining, AMD mitigation, isotopic analyses, Romania Rosia Montana is one of the most important European gold fields, with a long history of mining. The extraction of gold started on site during the Roman age, and the mining operations that spanned over almost two millennia have produced a visible environmental footprint. More than 140 km of mining galleries are documented by historical sources and recent surveys. Water streams are the main vectors spreading the pollution outside the mining area. The main streams, Rosia, Corna, and Saliste, tributaries of Abruzel River are significantly impacted by the acid waters issued by adits, exposed rock surfaces, or rock waste heaps, and tailings depots. Low contamination has been observed in the streams outside the mining area, artificial ponds, and shallow groundwater. Excepting the shallow groundwater system that can be sampled in domestic wells and some springs, the circulation of groundwater is largely unknown. An important amount of the infiltration water is channelled through galleries. The waters sampled at the galleries outlets have low pH, generally between 2 and 3, and very high content of heavy metals. A systematic approach based on monthly sampling and chemical analyses, and isotopic measurements, has been initiated, in order to better understand the underground itinerary of water and the chemical transformations that occur. A sampling network of 28 water points, including streams, ponds, dug wells, springs, and gallery outlets has been setup. Beyond producing a water circulation model in the mining area, the main purpose of the research is to identify ways of decreasing the acid water production and to design low cost techniques for the AMD mitigation. The deposit still hosts about 300 tonnes of gold, and 1600 tonnes of silver. A new large scale mining project is currently under permitting. Cost-effective solutions for the water treatment would be beneficial, especially for the post-mining stage of any future operation. Acknowledgments: The present contribution was financially supported by a grant of the Romanian National Authority for Scientific Research, CCCDI - UEFISCDI, project 3-005 Tools for sustainable gold mining in EU (SUSMIN). Dorian Brahaita has benefited from the financial support provided by the project POSDRU/159/1.5/S/132400.

30 CFR 780.29 - Diversions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.29 Diversions...

30 CFR 780.2 - Objectives.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.2 Objectives...

78 FR 5055 - Pattern of Violations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-23

...The Mine Safety and Health Administration (MSHA) is revising the Agency's existing regulation for pattern of violations (POV). MSHA has determined that the existing regulation does not adequately achieve the intent of the Federal Mine Safety and Health Act of 1977 (Mine Act) that the POV provision be used to address mine operators who have demonstrated a disregard for the health and safety of miners. Congress included the POV provision in the Mine Act so that mine operators would manage health and safety conditions at mines and find and fix the root causes of significant and substantial (S&S) violations, protecting the health and safety of miners. The final rule simplifies the existing POV criteria, improves consistency in applying the POV criteria, and more effectively achieves the Mine Act's statutory intent. It also encourages chronic safety violators to comply with the Mine Act and MSHA's health and safety standards.

Mine Improvement and New Emergency Response Act of 2006. Public Law 109-236, S2803

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2006-06-15

This Act may be cited as the 'Mine Improvement and New Emergency Response Act of 2006' or the 'MINER Act'. It amends the Federal Mine Safety and Health Act of 1977 to improve the safety of mines and mining. The Act requires operators of underground coal mines to improve accident preparedness. The legislation requires mining companies to develop an emergency response plan specific to each mine they operate, and requires that every mine has at least two rescue teams located within one hour. S. 2803 also limits the legal liability of rescue team members and the companies that employ them.more » The act increases both civil and criminal penalties for violations of federal mining safety standards and gives the Mine Safety and Health Administration (MSHA) the ability to temporarily close a mine that fails to pay the penalties or fines. In addition, the act calls for several studies into ways to enhance mine safety, as well as the establishment of a new office within the National Institute for Occupational Safety and Health devoted to improving mine safety. Finally, the legislation establishes new scholarship and grant programs devoted to training individuals with respect to mine safety.« less

Miners' Misconceptions of Flow Distribution Within Circuits as a Factor Influencing Underground Mining Accidents.

NASA Astrophysics Data System (ADS)

Passaro, Perry David

Misconceptions can be thought of as naive approaches to problem solving that are perceptually appealing but incorrect and inconsistent with scientific evidence (Piaget, 1929). One type of misconception involves flow distributions within circuits. This concept is important because miners' conceptual errors about flow distribution changes within complex circuits may be in part responsible for fatal mine disasters. Based on the theory that misconceptions of flow distribution changes within circuits were responsible for underground mine disasters involving mine ventilation circuits, a series of studies was undertaken with mining engineering students, professional mining engineers, as well as mine foremen, mine supervisors, mine rescue members, mine maintenance personnel, mining researchers and working miners to identify these conceptual errors and errors in mine ventilation procedures. Results indicate that misconceptions of flow distribution changes within circuits exist in over 70 percent of the subjects sampled. It is assumed that these misconceptions of flow distribution changes within circuits result in errors of judgment when miners are faced with inferring and changing ventilation arrangements when two or more mine sections are connected. Furthermore, it is assumed that these misconceptions are pervasive in the mining industry and may be responsible for at least two mine ventilation disasters. The findings of this study are consistent with Piaget's (1929) model of figurative and operative knowledge. This model states that misconceptions are in part due to a lack of knowledge of dynamic transformations and how to apply content information. Recommendations for future research include the development of an interactive expert system for training miners with ventilation arrangements. Such a system would meet the educational recommendations made by Piaget (1973b) by involving a hands-on approach that allows discovery, interaction, the opportunity to make mistakes and to review the cognitive concepts on which the subject relied during his manipulation of the ventilation system.

78 FR 31598 - Proposed Collection; Comment Request; Operations Under Water

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-24

...; Operations Under Water AGENCY: Mine Safety and Health Administration, Labor. ACTION: 60-Day Notice. SUMMARY... under bodies of water and to obtain a permit to mine under a body of water if, in the judgment of the... the inundation of underground coal mines with water that has the potential of drowning miners. Section...

26 CFR 50.1 - Introduction.

Code of Federal Regulations, 2010 CFR

2010-04-01

... supplied, and the total capital cost of said reservoir, which is to be repaid by tax on mining operations... and specifying in detail the manner in which operations shall proceed in such mine or mines; * * * Sec..., reservoir, and rights of way divided by the total capacity of the reservoir for the restraint of debris, as...

26 CFR 50.1 - Introduction.

Code of Federal Regulations, 2011 CFR

2011-04-01

... supplied, and the total capital cost of said reservoir, which is to be repaid by tax on mining operations... and specifying in detail the manner in which operations shall proceed in such mine or mines; * * * Sec..., reservoir, and rights of way divided by the total capacity of the reservoir for the restraint of debris, as...

30 CFR 50.30-1 - General instructions for completing MSHA Form 7000-2.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Operations, Preparation Plants, Breakers: Report data on all persons employed at your milling (crushing...) Employment, Employee Hours, and Coal Production—(1) Operation Sub-Unit: (i) Underground Mine: Report data for... underground mine, report data for those persons on the second line; (ii) Surface Mine (Including Shops and...

30 CFR 50.30-1 - General instructions for completing MSHA Form 7000-2.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Operations, Preparation Plants, Breakers: Report data on all persons employed at your milling (crushing...) Employment, Employee Hours, and Coal Production—(1) Operation Sub-Unit: (i) Underground Mine: Report data for... underground mine, report data for those persons on the second line; (ii) Surface Mine (Including Shops and...

30 CFR 780.10 - Information collection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.10... activities, including a requirement that the application include an operation and reclamation plan. The...

Statistical methods of estimating mining costs

USGS Publications Warehouse

Long, K.R.

2011-01-01

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to reestimate "Taylor's Rule" which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

CoalVal-A coal resource valuation program

USGS Publications Warehouse

Rohrbacher, Timothy J.; McIntosh, Gary E.

2010-01-01

CoalVal is a menu-driven Windows program that produces cost-of-mining analyses of mine-modeled coal resources. Geological modeling of the coal beds and some degree of mine planning, from basic prefeasibility to advanced, must already have been performed before this program can be used. United States Geological Survey mine planning is done from a very basic, prefeasibility standpoint, but the accuracy of CoalVal's output is a reflection of the accuracy of the data entered, both for mine costs and mine planning. The mining cost analysis is done by using mine cost models designed for the commonly employed, surface and underground mining methods utilized in the United States. CoalVal requires a Microsoft Windows? 98 or Windows? XP operating system and a minimum of 1 gigabyte of random access memory to perform operations. It will not operate on Microsoft Vista?, Windows? 7, or Macintosh? operating systems. The program will summarize the evaluation of an unlimited number of coal seams, haulage zones, tax entities, or other area delineations for a given coal property, coalfield, or basin. When the reader opens the CoalVal publication from the USGS website, options are provided to download the CoalVal publication manual and the CoalVal Program. The CoalVal report is divided into five specific areas relevant to the development and use of the CoalVal program: 1. Introduction to CoalVal Assumptions and Concepts. 2. Mine Model Assumption Details (appendix A). 3. CoalVal Project Tutorial (appendix B). 4. Program Description (appendix C). 5. Mine Model and Discounted Cash Flow Formulas (appendix D). The tutorial explains how to enter coal resource and quality data by mining method; program default values for production, operating, and cost variables; and ones own operating and cost variables into the program. Generated summary reports list the volume of resource in short tons available for mining, recoverable short tons by mining method; the seam or property being mined; operating cost per ton; and discounted cash flow cost per ton to mine and process the resources. Costs are calculated as loaded in a unit train, free-on-board the tipple, at a rate of return prescribed by the evaluator. The recoverable resources (in short tons) may be grouped by incremental cost over any range chosen by the user. For example, in the Gillette coalfield evaluation, the discounted cash flow mining cost (at an 8 percent rate of return) and its associated tonnage may be grouped by any applicable increment (for example, $0.10 per ton, $0.20 per ton, and so on) and using any dollar per ton range that is desired (for example, from $4.00 per ton to $15.00 per ton). This grouping ability allows the user to separate the coal reserves from the nonreserve resources and to construct cost curves to determine the effects of coal market fluctuations on the availability of coal for fuel whether for the generation of electricity or for coal-to-liquids processes. Coking coals are not addressed in this report.

30 CFR 49.3 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS § 49.3 Alternative mine rescue capability for... statement by the operator as to the number of miners willing to serve on a mine rescue team; (8) The...

30 CFR 49.3 - Alternative mine rescue capability for small and remote mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS § 49.3 Alternative mine rescue capability for... statement by the operator as to the number of miners willing to serve on a mine rescue team; (8) The...

Laser line scan performance prediction

NASA Astrophysics Data System (ADS)

Mahoney, Kevin L.; Schofield, Oscar; Kerfoot, John; Giddings, Tom; Shirron, Joe; Twardowski, Mike

2007-09-01

The effectiveness of sensors that use optical measurements for the laser detection and identification of subsurface mines is directly related to water clarity. The primary objective of the work presented here was to use the optical data collected by UUV (Slocum Glider) surveys of an operational areas to estimate the performance of an electro-optical identification (EOID) Laser Line Scan (LLS) system during RIMPAC 06, an international naval exercise off the coast of Hawaii. Measurements of optical backscattering and beam attenuation were made with a Wet Labs, Inc. Scattering Absorption Meter (SAM), mounted on a Rutgers University/Webb Research Slocum glider. The optical data universally indicated extremely clear water in the operational area, except very close to shore. The beam-c values from the SAM sensor were integrated to three attenuation lengths to provide an estimate of how well the LLS would perform in detecting and identifying mines in the operational areas. Additionally, the processed in situ optical data served as near-real-time input to the Electro-Optic Detection Simulator, ver. 3 (EODES-3; Metron, Inc.) model for EOID performance prediction. Both methods of predicting LLS performance suggested a high probability of detection and probability of identification. These predictions were validated by the actual performance of the LLS as the EOID system yielded imagery from which reliable mine identification could be made. Future plans include repeating this work in more optically challenging water types to demonstrate the utility of pre-mission UUV surveys of operational areas as a tactical decision aid for planning EOID missions.

30 CFR 57.7012 - Tending drills in operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tending drills in operation. 57.7012 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface Only § 57.7012 Tending drills in operation. While in operation...

30 CFR 56.7012 - Tending drills in operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tending drills in operation. 56.7012 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7012 Tending drills in operation. While in operation, drills shall be...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 910.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 910.795 Section 910.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE GEORGIA § 910.795 Small operator...

30 CFR 947.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 947.795 Section 947.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE WASHINGTON § 947.795 Small operator...

30 CFR 922.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 922.795 Section 922.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE MICHIGAN § 922.795 Small operator...

30 CFR 937.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 937.795 Section 937.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.795 Small operator...

30 CFR 56.7012 - Tending drills in operation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tending drills in operation. 56.7012 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7012 Tending drills in operation. While in operation, drills shall be...

30 CFR 56.7012 - Tending drills in operation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tending drills in operation. 56.7012 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7012 Tending drills in operation. While in operation, drills shall be...

30 CFR 56.7012 - Tending drills in operation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tending drills in operation. 56.7012 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7012 Tending drills in operation. While in operation, drills shall be...

30 CFR 57.7012 - Tending drills in operation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tending drills in operation. 57.7012 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface Only § 57.7012 Tending drills in operation. While in operation...

30 CFR 57.7012 - Tending drills in operation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tending drills in operation. 57.7012 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface Only § 57.7012 Tending drills in operation. While in operation...

30 CFR 57.7012 - Tending drills in operation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tending drills in operation. 57.7012 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface Only § 57.7012 Tending drills in operation. While in operation...

30 CFR 56.7012 - Tending drills in operation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tending drills in operation. 56.7012 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7012 Tending drills in operation. While in operation, drills shall be...

30 CFR 57.7012 - Tending drills in operation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tending drills in operation. 57.7012 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface Only § 57.7012 Tending drills in operation. While in operation...

30 CFR 912.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 912.795 Section 912.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE IDAHO § 912.795 Small operator...

30 CFR 75.1716 - Operations under water.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operations under water. 75.1716 Section 75.1716... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1716 Operations under water. [Statutory... working section of a mine opened prior to such date, in a manner that requires the construction, operation...

Potential for cobalt recovery from lateritic ores in Europe

NASA Astrophysics Data System (ADS)

Herrington, R.

2012-04-01

Cobalt is one of the 'critical metals' identified under the EU Raw Materials Initiative. Annually the global mine production of cobalt is around 55,000 tonnes,with Europe's industries consuming around 30% of that figure. Currently Europe produces around 27 tonnes of cobalt from mines in Finland although new capacity is planned. Co-bearing nickel laterite ores being mined in Greece, Macedonia and Kosovo where the cobalt is currently not being recovered (ores have typical analyses of 0.055% Co and >1% Ni,). These ores are currently treated directly in pyrometallurgical plants to recover the contained nickel and this process means there is no separate cobalt product produced. Hydrometallurgical treatment of mineralogically suitable laterite ores can recover the cobalt; for example Cuba recovers 3,500 tonnes of cobalt from its laterite mining operations, which are of a similar scale to the current European operations. Implementation of hydrometallurgical techniques is in its infancy in Europe with one deposit in Turkey planning to use atmospheric heap leaching to recover nickel and copper from oxide-dominated ores. More widespread implementation of these methods to mineralogically suitable ore types could unlock the highly significant undeveloped resources (with metal contents >0.04% Co and >1% Ni), which have been defined throughout the Balkans eastwards into Turkey. At a conservative estimate, this region has the potential to supply up to 30% of the EU cobalt requirements.

Deep-sea mining: potential environmental, legal, economic, and societal implications - an interdisciplinary research.

PubMed

Koschinsky, Andrea; Heinrich, Luise; Boehnke, Klaus; Cohrs, J Christopher; Markus, Till; Shani, Maor; Singh, Pradeep; Stegen, Karen Smith; Werner, Welf

2018-06-19

Deep-sea mining refers to the retrieval of marine mineral resources such as manganese nodules, ferromanganese crusts and seafloor massive sulfide deposits, which contain a variety of metals that serve as crucial raw materials for a range of applications, from electronic devices to renewable energy technologies to construction materials. With the intent of decreasing dependence on imports, supporting the economy and potentially even overcoming the environmental problems related to conventional terrestrial mining, a number of public and private institutions have re-discovered their interest in exploring the prospects of deep-sea mining, which had been deemed economically and technically unfeasible in the early 1980 s. To date, many national and international research projects are grappling to understand the economic environmental, social and legal implications of potential commercial deep-sea mining operations: a challenging endeavor due to the complexity of direct impacts and spill-over effects. In this paper, we present a comprehensive overview of the current state of knowledge in the aforementioned fields as well as a comparison of the impacts associated with conventional terrestrial mining. Furthermore, we identify knowledge gaps that should be urgently addressed to ensure that the world at large benefits from safe, efficient and environmentally-sound mining procedures. We conclude by highlighting the need for interdisciplinary research and international cooperation. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

30 CFR 75.1711-3 - Openings of active mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Openings of active mines. 75.1711-3 Section 75.1711-3 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY... active mines. The openings of all mines not declared by the operator, to be inactive, permanently closed...

30 CFR 75.1711-3 - Openings of active mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Openings of active mines. 75.1711-3 Section 75.1711-3 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY... active mines. The openings of all mines not declared by the operator, to be inactive, permanently closed...

30 CFR 75.1711-3 - Openings of active mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Openings of active mines. 75.1711-3 Section 75.1711-3 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY... active mines. The openings of all mines not declared by the operator, to be inactive, permanently closed...

30 CFR 75.1711-3 - Openings of active mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Openings of active mines. 75.1711-3 Section 75.1711-3 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY... active mines. The openings of all mines not declared by the operator, to be inactive, permanently closed...

30 CFR 46.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., but is not limited to, work as a heavy equipment operator, truck driver, skilled craftsman, or plant... or extended periods. (h) Mining operations means mine development, drilling, blasting, extraction...

The evaluation and quantification of respirable coal and silica dust concentrations: a task-based approach.

PubMed

Grové, T; Van Dyk, T; Franken, A; Du Plessis, J

2014-01-01

Silicosis and coal worker's pneumoconiosis are serious occupational respiratory diseases associated with the coal mining industry and the inhalation of respirable dusts containing crystalline silica. The purpose of this study (funded by the Mine Health and Safety Council of South Africa) was to evaluate the individual contributions of underground coal mining tasks to the respirable dust and respirable silica dust concentrations in an underground section by sampling the respirable dust concentrations at the intake and return of each task. The identified tasks were continuous miner (CM) cutting, construction, transfer of coal, tipping, and roof bolting. The respirable dust-generating hierarchy of the tasks from highest to lowest was: transfer of coal > CM right cutting > CM left cutting > CM face cutting > construction > roof bolting > tipping; and for respirable silica dust: CM left cutting > construction > transfer of coal > CM right cutting. Personal exposure levels were determined by sampling the exposures of workers performing tasks in the section. Respirable dust concentrations and low concentrations of respirable silica dust were found at the intake air side of the section, indicating that air entering the section is already contaminated. The hierarchy for personal respirable dust exposures was as follows, from highest to lowest: CM operator > cable handler > miner > roof bolt operator > shuttle car operator, and for respirable silica dust: shuttle car operator > CM operator > cable handler > roof bolt operator > miner. Dust control methods to lower exposures should include revision of the position of workers with regard to the task performed, positioning of the tasks with regard to the CM cutting, and proper use of the line curtains to direct ventilation appropriately. The correct use of respiratory protection should also be encouraged.

30 CFR 780.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.1 Scope. This part provides the... operations and reclamation plan portions of applications for permits for surface mining activities, except to...

EOID Evaluation and Automated Target Recognition

DTIC Science & Technology

2002-09-30

Electro - Optic IDentification (EOID) sensors into shallow water littoral zone minehunting systems on towed, remotely operated, and autonomous platforms. These downlooking laser-based sensors operate at unparalleled standoff ranges in visible wavelengths to image and identify mine-like objects (MLOs) that have been detected through other sensing means such as magnetic induction and various modes of acoustic imaging. Our long term goal is to provide a robust automated target cueing and identification capability for use with these imaging sensors. It is also our goal to assist

EOID Evaluation and Automated Target Recognition

DTIC Science & Technology

2001-09-30

Electro - Optic IDentification (EOID) sensors into shallow water littoral zone minehunting systems on towed, remotely operated, and autonomous platforms. These downlooking laser-based sensors operate at unparalleled standoff ranges in visible wavelengths to image and identify mine-like objects that have been detected through other sensing means such as magnetic induction and various modes of acoustic imaging. Our long term goal is to provide a robust automated target cueing and identification capability for use with these imaging sensors. It is also our goal to assist the

MINE WASTE TECHNOLOGY PROGRAM: A SUCCESS STORY

EPA Science Inventory

Mining Waste generated by active and inactive mining operations is a growing problem for the mining industry, local governments, and Native American communities because of its impact on human health and the environment. In the US, the reported volume of mine waste is immense: 2 b...

High area rate reconnaissance (HARR) and mine reconnaissance/hunter (MR/H) exploratory development programs

NASA Astrophysics Data System (ADS)

Lathrop, John D.

1995-06-01

This paper describes the sea mine countermeasures developmental context, technology goals, and progress to date of the two principal Office of Naval Research exploratory development programs addressing sea mine reconnaissance and minehunting technology development. The first of these programs, High Area Rate Reconnaissance, is developing toroidal volume search sonar technology, sidelooking sonar technology, and associated signal processing technologies (motion compensation, beamforming, and computer-aided detection and classification) for reconnaissance and hunting against volume mines and proud bottom mines from 21-inch diameter vehicles operating in deeper waters. The second of these programs, Amphibious Operation Area Mine Reconnaissance/Hunter, is developing a suite of sensor technologies (synthetic aperture sonar, ahead-looking sonar, superconducting magnetic field gradiometer, and electro-optic sensor) and associated signal processing technologies for reconnaissance and hunting against all mine types (including buried mines) in shallow water and very shallow water from 21-inch diameter vehicles. The technologies under development by these two programs must provide excellent capabilities for mine detection, mine classification, and discrimination against false targets.

Automatic mapping of strip mine operations from spacecraft data. [Ohio

NASA Technical Reports Server (NTRS)

Rogers, R. H. (Principal Investigator); Reed, L. E.; Pettyjohn, W. A.

1974-01-01

The author has identified the following significant results. Computer techniques were applied to process ERTS tapes acquired over coal mining operations in southeastern Ohio on 21 August 1972 and 3 September 1973. ERTS products obtained included geometrically-correct map overlays, at scales from 1:24,000 to 1:250,000, showing stripped earth, partially reclaimed earth, water, and natural vegetation. Computer-generated tables listing the area covered by each land-water category in square kilometers were also produced. By comparing these mapping products, the study demonstrates the capability of ERTS to monitor changes in the extent of stripping and reclamation. NASA C-130 photography acquired on 7 September 1973 when compared with the ERTS products generated from the 3 September 1973 tape established the categorization accuracy to be better than 90%. It is estimated that the stripping and reclamation maps and data were produced from the ERTS CCTs at a tenth of the cost of conventional techniques.

Mitigation planning for raptors during mining

DOE Office of Scientific and Technical Information (OSTI.GOV)

Platt, S.W.; Hargis, N.E.

1990-12-31

Birds of prey and their eggs, young and nests are protected by state and federal laws and regulations. Surface mining operators may experience conflicts with raptors when expanding into nesting areas or when raptors are attracted into mining areas. State and federal permits are required for disturbance or manipulation of birds of prey. Mitigation planning for raptors begins before mining and continues through mining. As conflict situations changes, so must the mitigation plan. Before each nesting season the mining schedule should be compared to areas of known raptor nesting activity. If overlap occurs, nest protection measures may be needed. Areasmore » of potential conflict should be patrolled regularly to identify the presence of a raptor pair and nest starts. Should a raptor nest be built and eggs laid, a change in the mining schedule or an egg or brood manipulation may resolve the conflict. Bridger Coal Company has successfully mitigated conflicts with 3 raptor species. A ferruginous hawk (Buteo regalis) nest with brood was successfully relocated across a pit. Red-tailed hawk (B. jamaicensis) egg clutches were removed from 2 highwall nests and transported in a portable incubator to a commercial raptor propagator where they were hatched, fed and conspecifically imprinted until achieving self-thermoregulation. All chicks were returned to the mine and successfully placed into foster nests. A metal artificial nest ledge for a prairie falcon (Falco mexicanus) was constructed in a cliff and a traditional nesting ledge rendered inaccessible. The falcon pair successfully nested in the artificial ledge.« less

Integrating weather and geotechnical monitoring data for assessing the stability of large scale surface mining operations

NASA Astrophysics Data System (ADS)

Steiakakis, Chrysanthos; Agioutantis, Zacharias; Apostolou, Evangelia; Papavgeri, Georgia; Tripolitsiotis, Achilles

2016-01-01

The geotechnical challenges for safe slope design in large scale surface mining operations are enormous. Sometimes one degree of slope inclination can significantly reduce the overburden to ore ratio and therefore dramatically improve the economics of the operation, while large scale slope failures may have a significant impact on human lives. Furthermore, adverse weather conditions, such as high precipitation rates, may unfavorably affect the already delicate balance between operations and safety. Geotechnical, weather and production parameters should be systematically monitored and evaluated in order to safely operate such pits. Appropriate data management, processing and storage are critical to ensure timely and informed decisions. This paper presents an integrated data management system which was developed over a number of years as well as the advantages through a specific application. The presented case study illustrates how the high production slopes of a mine that exceed depths of 100-120 m were successfully mined with an average displacement rate of 10- 20 mm/day, approaching an almost slow to moderate landslide velocity. Monitoring data of the past four years are included in the database and can be analyzed to produce valuable results. Time-series data correlations of movements, precipitation records, etc. are evaluated and presented in this case study. The results can be used to successfully manage mine operations and ensure the safety of the mine and the workforce.

Application of LANDSAT data and digital image processing. [Ruhr Valley, Germany

NASA Technical Reports Server (NTRS)

Bodechtel, J. (Principal Investigator)

1978-01-01

The author has identified the following significant results. Based on LANDSAT 1 and 2 data, applications in the fields of coal mining, lignite exploration, and thematic mapping in geology are demonstrated. The hybrid image processing system, its software, and its utilization for educational purposes is described. A pre-operational European satellite is proposed.

77 FR 22609 - Notice of Intent To Prepare an Environmental Impact Statement for the Proposed Pan Mine Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-16

... business hours. SUPPLEMENTARY INFORMATION: Midway Gold US Inc. (Midway) proposes to construct and operate an open-pit gold mining operation, which would include open pits, a heap leach pad, waste rock dumps, and ancillary facilities. The mine would be located in the northern part of the Pancake Mountain Range...

Determining Underground Mining Work Postures Using Motion Capture and Digital Human Modeling

PubMed Central

Lutz, Timothy J.; DuCarme, Joseph P.; Smith, Adam K.; Ambrose, Dean

2017-01-01

According to Mine Safety and Health Administration (MSHA) data, during 2008–2012 in the U.S., there were, on average, 65 lost-time accidents per year during routine mining and maintenance activities involving remote-controlled continuous mining machines (CMMs). To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is currently investigating the implementation and integration of existing and emerging technologies in underground mines to provide automated, intelligent proximity detection (iPD) devices on CMMs. One research goal of NIOSH is to enhance the proximity detection system by improving its capability to track and determine identity, position, and posture of multiple workers, and to selectively disable machine functions to keep workers and machine operators safe. Posture of the miner can determine the safe working distance from a CMM by way of the variation in the proximity detection magnetic field. NIOSH collected and analyzed motion capture data and calculated joint angles of the back, hips, and knees from various postures on 12 human subjects. The results of the analysis suggests that lower body postures can be identified by observing the changes in joint angles of the right hip, left hip, right knee, and left knee. PMID:28626796

Rapid assessment of environmental health risks posed by mining operations in low- and middle-income countries: selected case studies.

PubMed

Caravanos, Jack; Ericson, Bret; Ponce-Canchihuamán, Johny; Hanrahan, David; Block, Meredith; Susilorini, Budi; Fuller, Richard

2013-11-01

Previous studies have evaluated associated health risks and human exposure pathways at mining sites. Others have provided estimates of the scale of the issue based in part on surveys. However, a global census of mining-related hazardous waste sites has been lacking. The Toxic Sites Identification Program (TSIP) implemented by Blacksmith Institute (New York, NY, USA) since 2009 is an ongoing effort to catalogue a wide range of chemically contaminated sites with a potential human health risk (Ericson et al., Environ Monit Assess doi:10.1007/s 10661-012-2665-2, 2012). The TSIP utilizes a rapid assessment instrument, the Initial Site Screening (ISS), to quickly and affordably identify key site criteria including human exposure pathways, estimated populations at risk, and sampling information. The resulting ISS allows for comparison between sites exhibiting different contaminants and pollution sources. This paper explores the results of a subset of ISSs completed at 131 artisanal and small-scale gold mining areas and 275 industrial mining and ore processing sites in 45 countries. The authors show that the ISS captures key data points, allowing for prioritization of sites for further investigation or remedial activity.

Logistic Principles Application for Managing the Extraction and Transportation of Solid Minerals

NASA Astrophysics Data System (ADS)

Tyurin, Alexey

2017-11-01

Reducing the cost of resources in solid mineral extraction is an urgent task. For its solution the article proposes logistic approach use to management of mining company all resources, including extraction processes, transport, mineral handling and storage. The account of the uneven operation of mining, transport units and complexes for processing and loading coal into railroad cars allows you to identify the shortcomings in the work of the entire enterprise and reduce resources use at the planned production level. In the article the mining planning model taking into account the dynamics of the production, transport stations and export coal to consumers rail transport on example of Krasnoyarsk region Nazarovo JSC «Razrez Sereul'skiy». Rolling planning methods use and data aggregation allows you to split the planning horizon (month) on equal periods and to use of dynamic programming method for building mining optimal production programme for the month. Coal mining production program definition technique will help align the work of all enterprise units, to optimize resources of all areas, to establish a flexible relationship between manufacturer and consumer, to take into account the irregularity of rail transport.

30 CFR 785.14 - Mountaintop removal mining.

Code of Federal Regulations, 2011 CFR

2011-07-01

... mountaintop removal mining. (b) Mountaintop removal mining means surface mining activities, where the mining operation removes an entire coal seam or seams running through the upper fraction of a mountain, ridge, or... adjacent land uses; (B) Obtainable according to data regarding expected need and market; (C) Assured of...

Impacts of historical mining in the Coeur d'Alene River Basin

USGS Publications Warehouse

Balistrieri, Laurie S.; Box, Stephen E.; Bookstrom, Arthur A.; Hooper, Robert L.; Mahoney, J. Brian

2010-01-01

Mining began in the late 1880s in the Coeur d'Alene mining district in northern Idaho (fig. 1). Although only two mines, the Galena and Lucky Friday, currently are operating, more than 90 historical mines exist in this region (Bennett and others, 1989).

30 CFR 795.12 - Applicant liability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SMALL OPERATOR ASSISTANCE PERMANENT REGULATORY PROGRAM-SMALL OPERATOR ASSISTANCE PROGRAM § 795.12 Applicant... 12 months immediately following the date on which the operator is issued the surface coal mining and...

Case history of controlling a landslide at Panluo open-pit mine in China

NASA Astrophysics Data System (ADS)

Wei, Zuoan; Yin, Guangzhi; Wan, Ling; Shen, Louyan

2008-04-01

Controlling of landsides safely and economically is a great challenge to mine operators because landslides are major geological problems especially in open-pit mines. In this paper, a case history at Panluo open-pit mine is presented in detail to share the experiences and lessons with mine operators. Panluo open-pit mine is located in the southwestern Fujian province of China. It is the largest open-pit iron mine in the Fujian province and was planned in 1965 and is in full operation from 1978. In July 1990, an earthquake of magnitude 5.3 in Taiwan Strait and big rainstorms impacted the mine slope, causing tension cracks and rather large-scale failures, and forming a U-shaped landslide. Total potential volume was estimated to be up to 1.0 × 106 m3. This directly threatened the mine production. In order to protect the mine production and the dwellers’ safety around, a dynamic comprehensive method was implemented including geotechnical investigations, in-situ testing and monitoring, stability analysis, and many mitigation and preventive measures. These measures slowed down the development and further occurrence of the landslide. The results showed that the landslides were still active, it was slowed with the control measures and moved rapidly with rainfall and mining down. However, no catastrophic accidents occurred and the pit mining was continued till it was closed at the elevation of 887 m in 2000. As a successful case of landslide control at an open-pit mine for 10 years, this paper reports the controlling measures in details. These experiences of landslide control may be beneficial to other similar mines for landslide control.

Teleoperated control system for underground room and pillar mining

DOEpatents

Mayercheck, William D.; Kwitowski, August J.; Brautigam, Albert L.; Mueller, Brian K.

1992-01-01

A teleoperated mining system is provided for remotely controlling the various machines involved with thin seam mining. A thin seam continuous miner located at a mining face includes a camera mounted thereon and a slave computer for controlling the miner and the camera. A plurality of sensors for relaying information about the miner and the face to the slave computer. A slave computer controlled ventilation sub-system which removes combustible material from the mining face. A haulage sub-system removes material mined by the continuous miner from the mining face to a collection site and is also controlled by the slave computer. A base station, which controls the supply of power and water to the continuous miner, haulage system, and ventilation systems, includes cable/hose handling module for winding or unwinding cables/hoses connected to the miner, an operator control module, and a hydraulic power and air compressor module for supplying air to the miner. An operator controlled host computer housed in the operator control module is connected to the slave computer via a two wire communications line.

30 CFR 947.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 947.784 Section 947.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. (a) Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 922.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 922.784 Section 922.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 905.780 - Surface mining permit applications-Minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 905.780 Section 905.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 933.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 933.784 Section 933.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 939.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 939.784 Section 939.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 910.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 910.780 Section 910.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirement for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 941.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 941.784 Section 941.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 947.780 - Surface mining permit application-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 947.780 Section 947.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Application—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 937.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 937.780 Section 937.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirement for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 912.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 912.784 Section 912.784 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 903.780 - Surface mining permit applications-Minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 903.780 Section 903.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, applies to any person who submits an application to conduct...

30 CFR 942.780 - Surface mining permit applications-Minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 942.780 Section 942.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 942.784 - Underground mining permit applications-Minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 942.784 Section 942.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 921.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 921.784 Section 921.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 905.784 - Underground mining permit applications-Minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 905.784 Section 905.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 937.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 937.784 Section 937.784 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 910.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 910.784 Section 910.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. (a) Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 941.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 941.780 Section 941.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 912.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 912.780 Section 912.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 933.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 933.780 Section 933.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 939.780 - Surface mining permit applications-minimum requirements for reclamation and operations plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operations plan. 939.780 Section 939.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operations plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 921.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 921.780 Section 921.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 903.784 - Underground mining permit applications-Minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 903.784 Section 903.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, applies to any person who submits an application...

30 CFR 922.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for reclamation and operation plan. 922.780 Section 922.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

Mining Permits - Division of Mining, Land, and Water

Science.gov Websites

are issued for a term of 1-5 years. An application for a "single year" operation costs $150 ). Federal Operators: If your operation involves federal land managed by the Bureau of Land Management (BLM issues miners the Alaska Pollutant Discharge Elimination System (APDES) General Permit. If the operation

36 CFR 9.9 - Plan of operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Plan of operations. 9.9 Section 9.9 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT Mining and Mining Claims § 9.9 Plan of operations. (a) No operations shall be conducted within any...

36 CFR 9.9 - Plan of operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Plan of operations. 9.9 Section 9.9 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT Mining and Mining Claims § 9.9 Plan of operations. (a) No operations shall be conducted within any...

36 CFR 9.9 - Plan of operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Plan of operations. 9.9 Section 9.9 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT Mining and Mining Claims § 9.9 Plan of operations. (a) No operations shall be conducted within any...

36 CFR 9.9 - Plan of operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Plan of operations. 9.9 Section 9.9 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT Mining and Mining Claims § 9.9 Plan of operations. (a) No operations shall be conducted within any...

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport

PubMed Central

Shahan, M.R.; Seaman, C.E.; Beck, T.W.; Colinet, J.F.; Mischler, S.E.

2017-01-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. PMID:28936001

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

Thin seam miner/trench mining concepts for Illinois Basin surface coal mines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caudle, R.D.; Lall, V.

1985-07-01

A hybrid surface/underground mining concept, trench-auger mining is an attempt to increase the depth to which coal seams can be surface mined economically by reducing the amount of overburden which must be removed and reclaimed. In this concept the coal seam is first exposed by digging a series of parallel trenches 400 to 1200 ft apart with conventional surface mining equipment. After surface mining the coal from the bottom of the trench, the coal under the surface between the trenches would be extracted with extended-depth augers, operating from the bottoms of the trenches. The RSV Mining Equipment Co. of Hollandmore » has developed a Thin Seam Miner (TSM). The TSM is essentially a remotely controlled, continuous underground mining machine. The hydraulically driven drum cutter head and coal handling auger flights can be operated from a distance outside the underground mine workings. The purpose of this study is to develop and evaluate Thin Seam Miner/Trench Mining (TSM/TM) concepts for use under conditions existing in the Illinois Coal Basin.« less

30 CFR 939.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall become applicable...

30 CFR 903.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities, applies to surface...

30 CFR 939.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall become applicable...

30 CFR 903.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities, applies to surface...

30 CFR 903.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities, applies to surface...

30 CFR 939.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall become applicable...

30 CFR 939.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall become applicable...

30 CFR 939.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall become applicable...

30 CFR 903.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities, applies to surface...

Mercury emission and distribution: Potential environmental risks at a small-scale gold mining operation, Phichit Province, Thailand.

PubMed

Pataranawat, Poranee; Parkpian, Preeda; Polprasert, Chongrak; Delaune, R D; Jugsujinda, A

2007-07-01

Mercury (Hg) contamination was assessed in environment near an amalgamation gold recovery operation located at a small scale mining operation (Phanom Pha) in Phichit Province, Thailand. Total mercury (THg) concentrations was determined in water, sediment, bivalves in the aquatic environment and as dry deposition or atmospheric fallout on surface soil and leaves of Neem tree (Azadirachta indica Juss. var. siamensis Valeton) near the mining operation. THg in surface soil, Neem flowers (edible part) and rice grain in surrounding terrestrial habitat and with distance from the mining area were also evaluated for possible contamination. Potential environmental risks were evaluated using the hazard quotient equation. Hg analyses conducted in the aquatic habitat showed that THg in water, sediment and bivalves (Scabies cripata Gould) ranged from 0.4 to 4 microg L(-1), 96 to 402 microg kg(-1)dry weight (dw) and 15 to 584 microg kg(-1) wet weight (ww), respectively. High concentrations of THg in water, sediment and bivalves were observed in the receiving stream near the mining operation which was located near the Khao Chet Luk Reservoir. Whereas the THg concentration in water, sediment and bivalves from monitoring stations outside the gold mining operation (upstream and downstream), were considerably lower with the values of 0.4-0.8 microg L(-1), 96-140 microg kg(-1) dw and 88-658 microg kg(-1) dw, respectively. The elevated concentration of Hg found in the sediment near the mining operation was consistent with Hg accumulation measured in bivalves. The elevated Hg levels found in living bivalves collected from highly contaminated sites suggested that the sediment bound Hg was bioavailable. THg in surface soils, brown rice grain (Jasmine rice #105) and Neem flowers of terrestrial habitats were in the range of 16 to 180 microg kg(-1) dw, 190 to 300 microg kg(-1) dw, and 622 to 2150 microg kg(-1) dw, respectively. Elevated concentrations of mercury were found in Neem flowers with the concentration greater than 600 microg kg(-1) ww, which exceeds the maximum permissible concentration reported for biota tissue (500 microg kg(-1) ww). An evaluation of air and soil pollution near the mining operations showed high concentrations of THg in dry deposit from atmospheric fallout (139 microg m(-2) d(-1)), and in surface soil (10,564 microg kg(-1) dw) at station near where open burning of gold ore extracts using the amalgamation process occurred. High or elevated concentration of THg (1172-1301 microg kg(-1) dw) in leaves of Neem tree was also measured near the mining operations. A survey of Hg in surface soil showed elevated Hg concentrations near the site which corresponded to the elevated THg concentration in dry deposition. These results suggested that atmospheric fallout is a major source of Hg to the area surrounding the mining or gold ore extraction. Results also suggest that Hg emitted into the air (estimated to be 60-150 g d(-1)) from the gold mining activities (over the past 10 years) contaminated air, the aquatic environment, surface soil and biota in the area surrounding the gold mining operation.

Mining the human gut microbiota for effector strains that shape the immune system

PubMed Central

Ahern, Philip P.; Faith, Jeremiah J.; Gordon, Jeffrey I.

2014-01-01

Summary The gut microbiota co-develops with the immune system beginning at birth. Mining the microbiota for bacterial strains responsible for shaping the structure and dynamic operations of the innate and adaptive arms of the immune system represents a formidable combinatorial problem but one that needs to be overcome to advance mechanistic understanding of microbial community-immune system co-regulation, and in order to develop new diagnostic and therapeutic approaches that promote health. Here, we discuss a scalable, less biased approach for identifying effector strains in complex microbial communities that impact immune function. The approach begins by identifying uncultured human fecal microbiota samples that transmit immune phenotypes to germ-free mice. Clonally-arrayed sequenced collections of bacterial strains are constructed from representative donor microbiota. If the collection transmits phenotypes, effector strains are identified by testing randomly generated subsets with overlapping membership in individually-housed germ-free animals. Detailed mechanistic studies of effector strain-host interactions can then be performed. PMID:24950201

30 CFR 716.5 - Anthracite coal mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Anthracite coal mines. 716.5 Section 716.5... PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.5 Anthracite coal mines. (a) Permittees of anthracite surface coal mining and reclamation operations in those States where the mines are regulated by...

30 CFR 716.5 - Anthracite coal mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Anthracite coal mines. 716.5 Section 716.5... PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.5 Anthracite coal mines. (a) Permittees of anthracite surface coal mining and reclamation operations in those States where the mines are regulated by...

30 CFR 716.5 - Anthracite coal mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Anthracite coal mines. 716.5 Section 716.5... PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.5 Anthracite coal mines. (a) Permittees of anthracite surface coal mining and reclamation operations in those States where the mines are regulated by...

30 CFR 716.5 - Anthracite coal mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Anthracite coal mines. 716.5 Section 716.5... PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.5 Anthracite coal mines. (a) Permittees of anthracite surface coal mining and reclamation operations in those States where the mines are regulated by...

30 CFR 716.5 - Anthracite coal mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Anthracite coal mines. 716.5 Section 716.5... PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.5 Anthracite coal mines. (a) Permittees of anthracite surface coal mining and reclamation operations in those States where the mines are regulated by...

30 CFR 57.22003 - Mine category or subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Methane in Metal and Nonmetal Mines Mine Categorization § 57.22003 Mine category or... methane and dusts containing volatile matter. Categories and subcategories are defined as follows: (1) Category I applies to mines that operate within a combustible ore body and either liberate methane or have...

30 CFR 912.785 - Requirements for permits for special categories of mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of mining. 912.785 Section 912.785 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE IDAHO § 912.785 Requirements for permits for special categories of mining. Part 785 of this...

30 CFR 903.785 - Requirements for permits for special categories of mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of mining. 903.785 Section 903.785 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE ARIZONA § 903.785 Requirements for permits for special categories of mining. Part 785 of this...

25 CFR 215.23 - Cooperation between superintendent and district mining supervisor.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Cooperation between superintendent and district mining... MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.23 Cooperation between superintendent and district mining supervisor. (a) The district mining supervisor of the Miami field office...

30 CFR 905.785 - Requirements for permits for special categories of mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of mining. 905.785 Section 905.785 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE CALIFORNIA § 905.785 Requirements for permits for special categories of mining. Part 785 of this...

30 CFR 910.785 - Requirements for permits for special categories of mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of mining. 910.785 Section 910.785 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE GEORGIA § 910.785 Requirements for permits for special categories of mining. Part 785 of this...

30 CFR 49.5 - Mine rescue station.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Mine rescue station. 49.5 Section 49.5 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS § 49.5 Mine rescue station. (a) Except where alternative compliance is permitted, every operator...

30 CFR 49.5 - Mine rescue station.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Mine rescue station. 49.5 Section 49.5 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS § 49.5 Mine rescue station. (a) Except where alternative compliance is permitted, every operator...

36 CFR 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... mineral leasing. 1005.14 Section 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing laws are...

36 CFR 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... mineral leasing. 1005.14 Section 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing laws are...

36 CFR 1005.14 - Prospecting, mining, and mineral leasing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... mineral leasing. 1005.14 Section 1005.14 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.14 Prospecting, mining, and mineral leasing. Prospecting, mining, and the location of mining claims under the general mining laws and leasing under the mineral leasing laws are...

43 CFR 3487.1 - Logical mining units.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Logical mining units. 3487.1 Section 3487..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) COAL EXPLORATION AND MINING OPERATIONS RULES Logical Mining Unit § 3487.1 Logical mining units. (a) An LMU shall become effective only upon approval of the...

30 CFR 750.13 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 750.13 Section 750.13 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS...

30 CFR 947.843 - Federal enforcement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... planning department in the county government where the operation is located, a copy of the enforcement... PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE WASHINGTON § 947.843 Federal... required for violations on surface coal mining and reclamation operations. (b) Upon request OSM shall...

30 CFR 922.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 922.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 947.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 941.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 922.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 912.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 905.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 910.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 905.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 905.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 941.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 912.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 941.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 922.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 947.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 947.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 941.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 910.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 910.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 910.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 905.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitions, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 941.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 912.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 947.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 947.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 922.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

30 CFR 912.764 - Process for designating areas unsuitable for surface coal mining operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mining Operations, pertaining to petitioning, initial processing, hearing requirements, decisions, data base and inventory systems, public information, and regulatory responsibilities shall apply to surface...

The Fox Guarding the Chicken Coop: Monitoring Exposure to Respirable Coal Mine Dust, 1969–2000

PubMed Central

Weeks, James L.

2003-01-01

Following passage of the Coal Mine Health and Safety Act of 1969, underground coal mine operators were required to take air samples in order to monitor compliance with the exposure limit for respirable dust, a task essential for the prevention of pneumoconiosis among coal workers. Miners objected, claiming that having the mine operators perform this task was like “having the fox guard the chicken coop.” This article is a historical narrative of mining industry corruption and of efforts to reform the program of monitoring exposure to coal mine dust. Several important themes common to the practice of occupational health are illustrated; most prominently, that employers should not be expected to regulate themselves. PMID:12893602

Lunar surface mine feasibility study

NASA Astrophysics Data System (ADS)

Blair, Brad R.

This paper describes a lunar surface mine, and demonstrates the economic feasibility of mining oxygen from the moon. The mine will be at the Apollo 16 landing site. Mine design issues include pit size and shape, excavation equipment, muck transport, and processing requirements. The final mine design will be driven by production requirements, and constrained by the lunar environment. This mining scenario assumes the presence of an operating lunar base. Lunar base personnel will set-up a and run the mine. The goal of producing lunar oxygen is to reduce dependence on fuel shipped from Earth. Thus, the lunar base is the customer for the finished product. The perspective of this paper is that of a mining contractor who must produce a specific product at a remote location, pay local labor, and sell the product to an onsite captive market. To make a profit, it must be less costly to build and ship specialized equipment to the site, and pay high labor and operating costs, than to export the product directly to the site.

78 FR 77706 - Notice of Intent To Prepare an Environmental Impact Statement for the Proposed Gemfield Mine...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

... gold mine and associated processing and ancillary facilities. The project would be located on public... media, newspapers and the BLM Web site at: http://www.blm.gov/nv/st/en/fo/battle_mountain_field.html... to construct, operate, reclaim, and close an open pit, heap leach, gold mining operation known as the...

Implementation plan for Bolivian Mineral Exploration Fund

USGS Publications Warehouse

Kirkemo, Harold

1978-01-01

Bolivia ranks second among world producers of tin and antimony, and first in bismuth production. Mineral exports in 1975 were valued at $314.2 million, nearly 60 percent of the value of all exports, and petroleum product exports totalled nearly $157 million, or 30 percent of the total. Tin accounted for 58 percent of the total value of metallic mineral exports. The central government derived about 19 percent of its total tax revenues in 1975 from the mining sector. The mining sector consists of the large, medium, and small mining subsectors, a classification established by the government. Individual operations are referred to as large, medium, or small depending upon the subsector into which they are classified. All large mining enterprises are owned and operated by a government corporation, COMIBOL; the medium and small operations are privately owned. COMIBOL's exports in 1975 were valued at $171.8 million or 70 percent of the total mineral exports; the medium mines accounted for $55.5 million or 23 percent, and the small mines for $17.5 million or 7 percent of the total. The combination of high operating costs, low productivity, inadequate ore reserves, and insufficient risk capital for exploration and development has led to the realization that there is an urgent need to improve the situation for mining in Bolivia. Proposals are being studied to revise the tax code, a program is underway to evaluate selected mineral deposits for possible exploration and development, and programs are under consideration to encourage minerals exploration. A minerals exploration plan is proposed which would offer technical and financial aid to various segments in the minerals field. A program, estimated to cost between $2 million and $2.5 million annually, and to be operated by a new agency in the Ministry of Mining and Metallurgy, is outlined.

Conceptual overview and preliminary risk assessment of cryogen use in deep underground mine production

NASA Astrophysics Data System (ADS)

Sivret, J.; Millar, D. L.; Lyle, G.

2017-12-01

This research conducts a formal risk assessment for cryogenic fueled equipment in underground environments. These include fans, load haul dump units, and trucks. The motivating advantage is zero-emissions production in the subsurface and simultaneous provision of cooling for ultra deep mine workings. The driving force of the engine is the expansion of the reboiled cryogen following flash evaporation using ambient temperature heat. The cold exhaust mixes with warm mine air and cools the latter further. The use of cryogens as ‘fuel’ leads to much increased fuel transport volumes and motivates special considerations for distribution infrastructure and process including: cryogenic storage, distribution, handling, and transfer systems. Detailed specification of parts and equipment, numerical modelling and preparation of design drawings are used to articulate the concept. The conceptual design process reveals new hazards and risks that the mining industry has not yet encountered, which may yet stymie execution. The major unwanted events include the potential for asphyxiation due to oxygen deficient atmospheres, or physical damage to workers due to exposure to sub-cooled liquids and cryogenic gases. The Global Minerals Industry Risk Management (GMIRM) framework incorporates WRAC and Bow-Tie techniques and is used to identify, assess and mitigate risks. These processes operate upon the competing conceptual designs to identify and eliminate high risk options and improve the safety of the lower risk designs.

Investigation of human body vibration exposures on haul trucks operating at U.S. surface mines/quarries relative to haul truck activity.

PubMed

Mayton, Alan G; Porter, William L; Xu, Xueyan S; Weston, Eric B; Rubenstein, Elaine N

2018-03-01

Workers who operate mine haul trucks are exposed to whole-body vibration (WBV) on a routine basis. Researchers from the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) investigated WBV and hand-arm vibration (HAV) exposures for mine/quarry haul truck drivers in relation to the haul truck activities of dumping, loading, and traveling with and without a load. The findings show that WBV measures in weighted root-mean-square accelerations (a w ) and vibration dose value (VDV), when compared to the ISO/ANSI and European Directive 2002/44/EC standards, were mostly below the Exposure Action Value (EAV) identified by the health guidance caution zone (HGCZ). Nevertheless, instances were recorded where the Exposure Limit Value (ELV) was exceeded by more than 500 to 600 percent for VDV x and a wx , respectively. Researchers determined that these excessive levels occurred during the traveling empty activity, when the haul truck descended down grade into the pit loading area, sliding at times, on a wet and slippery road surface caused by rain and overwatering. WBV levels (not normalized to an 8-h shift) for the four haul truck activities showed mean a wz levels for five of the seven drivers exceeding the ISO/ANSI EAV by 9-53 percent for the traveling empty activity. Mean a wx and a wz levels were generally higher for traveling empty and traveling loaded and lower for loading/dumping activities. HAV for measures taken on the steering wheel and shifter were all below the HGCZ which indicates that HAV is not an issue for these drivers/operators when handling steering and shifting control devices.

Investigation of human body vibration exposures on haul trucks operating at U.S. surface mines/quarries relative to haul truck activity

PubMed Central

Mayton, Alan G.; Porter, William L.; Xu, Xueyan S.; Weston, Eric B.; Rubenstein, Elaine N.

2018-01-01

Workers who operate mine haul trucks are exposed to whole-body vibration (WBV) on a routine basis. Researchers from the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) investigated WBV and hand-arm vibration (HAV) exposures for mine/quarry haul truck drivers in relation to the haul truck activities of dumping, loading, and traveling with and without a load. The findings show that WBV measures in weighted root-mean-square accelerations (aw) and vibration dose value (VDV), when compared to the ISO/ANSI and European Directive 2002/44/EC standards, were mostly below the Exposure Action Value (EAV) identified by the health guidance caution zone (HGCZ). Nevertheless, instances were recorded where the Exposure Limit Value (ELV) was exceeded by more than 500 to 600 percent for VDVx and awx, respectively. Researchers determined that these excessive levels occurred during the traveling empty activity, when the haul truck descended down grade into the pit loading area, sliding at times, on a wet and slippery road surface caused by rain and overwatering. WBV levels (not normalized to an 8-h shift) for the four haul truck activities showed mean awz levels for five of the seven drivers exceeding the ISO/ANSI EAV by 9–53 percent for the traveling empty activity. Mean awx and awz levels were generally higher for traveling empty and traveling loaded and lower for loading/dumping activities. HAV for measures taken on the steering wheel and shifter were all below the HGCZ which indicates that HAV is not an issue for these drivers/operators when handling steering and shifting control devices. PMID:29725145

UNDERSTANDING THE IMPACT OF ENVIRONMENTAL VARIABLES ON THE LEACHING OF MERCURY-CONTAMINATED MINE WASTES FROM THE SULFUR BANK MERCURY MINE, CLEAR LAKE, CA

EPA Science Inventory

For nearly a century, Clear Lake in northern California has received inputs of mercury (Hg) mining wastes trom the Sulfur Bank Mercury Mine (SBMM). About 1.2 million tons of Hg-contaminated overburden and mine tailings were distributed over a 50-ha surface area due to mining oper...

Long term contracts, expansion, innovation and stability: North Dakota's lignite mines thrive

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchsbaum, L.

2009-08-15

North Dakota's lignite coal industry is mainly located in three countries in the central part of the state. Its large surface lignite mines are tied through long-term (20-40 years) contracts to power plants. The article talks about operations at three of the most productive mines - the Freedom mine, Falkirk mine and Center Mine. 4 figs.

30 CFR 921.795 - Small operator assistance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Small operator assistance. 921.795 Section 921.795 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE MASSACHUSETTS § 921.795 Small...

30 CFR 57.15014 - Eye protection when operating grinding wheels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Eye protection when operating grinding wheels. 57.15014 Section 57.15014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... NONMETAL MINES Personal Protection Surface and Underground § 57.15014 Eye protection when operating...

30 CFR 57.15014 - Eye protection when operating grinding wheels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Eye protection when operating grinding wheels. 57.15014 Section 57.15014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... NONMETAL MINES Personal Protection Surface and Underground § 57.15014 Eye protection when operating...

30 CFR 947.842 - Federal inspections.

Code of Federal Regulations, 2010 CFR

2010-07-01

... planning department in the county government where the operation is located, a copy of the enforcement... PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE WASHINGTON § 947.842 Federal... coal mining and reclamation operations. (b) Upon request OSM shall furnish a copy of any inspection...

Boron in tree-ring as an indicator of forest disturbances in the Lower Athabasca Oil Sands region, Northeastern Alberta, Canada

NASA Astrophysics Data System (ADS)

Bégin, Christian; Savard, Martine M.; Marion, Joëlle; Thiffault, Évelyne; Pinno, Brad

2016-04-01

Industrial activities related to oil sands (OS) extraction in northeastern Alberta (Canada) have generated, since 1967, important quantities of NOx and SO2 emissions that can lead to several negative effects on forest ecosystems including the potential for soil acidification. In addition, mining processes, tailing pond treatments and heavy transport (haul roads) in mining areas are considered important sources of air contaminants that have the potential to impair forest health by affecting the nutrient balance and physiology of trees. In this study, we analysed micronutrients (B, Fe, Zn, Na, Cu) and macronutrients (Ca, Mg, Mn, K) in the tree-ring series of jack pine (Pinus banksiana) and spruce (Picea glauca and Picea mariana) trees growing at different distances from the heart of mining operations (two sites for each species). Based on tree-ring records, our aims were to provide a historical perspective on the nutritional status of forest ecosystems and to identify temporal changes in tree-ring chemistry that can be attributed to OS activities. One of the key findings of this research is the direct and immediate response of boron (B) in woody tissues of all studied species to mining operations. During the pre-mining period (prior to 1967) [B] variations in tree-rings of the three species covary with other elements such as Na and Fe and are likely controlled by environmental factors, namely climatic conditions. After 1970, [B] increases and strongly departs from trends of other elements. In jack pine trees (54 km NNE of the centre of industrial operations) the increasing trend is abrupt with mean [B] increasing from 11.7 mg/kg during the pre-industrial period to 14.3 mg/kg during mining period. In spruce trees at the proximal site (14 km NE), [B] increases gradually and nicely reproduces the historical pattern of industrial emissions with mean pre-mining [B] of 29.5 mg/kg increasing to 92.1 mg/kg during the mining period. At the four spruce sites, the increasing rate of B decrease with distance and no specific trend in [B] was found at the distal site (135 km E). Finally, a significant negative correlation was found between [B] and tree growth within the mining area suggesting a potential negative role of anthropogenic emissions on forest productivity. Mining and associated industrial activities in the Alberta OS region are known to have the potential of releasing substantial quantities of B in the environment. Even if B specific emissions remain poorly documented in the area, the high [B] in top organic soil horizons at all sites confirm the atmospheric source for B. Rarely investigated in dendrogeochemical studies, B in the tree-rings, along with other associated nutrients, appears to be an excellent biogeochemical indicator of disturbances in nutritional status of forests in the vicinity of Alberta OS mining activities.