Calculation of thermodynamic properties and transport coefficients of C5F10O-CO2 thermal plasmas

NASA Astrophysics Data System (ADS)

Li, Xingwen; Guo, Xiaoxue; Murphy, Anthony B.; Zhao, Hu; Wu, Jian; Guo, Ze

2017-10-01

The thermodynamic properties and transport coefficients of C5F10O-CO2 gas mixtures, which are being considered as substitutes for SF6 in circuit breaker applications, are calculated for the temperature range from 300 K to 30 000 K and the pressure range from 0.05 MPa to 1.6 MPa. Special attention is paid on investigating the evolution of thermophysical properties of C5F10O-CO2 mixtures with different mixing ratios and with different pressures; both the mixing ratio and pressure significantly affect the properties. This is explained mainly in terms of the changes in the temperatures at which the dissociation and ionization reactions take place. Comparisons of different thermophysical properties of C5F10O-CO2 mixtures with those of SF6 are also carried out. It is found that most of the thermophysical properties of the C5F10O-CO2 mixtures, such as thermal conductivity, viscosity, and electrical conductivity, become closer to those of SF6 as the C5F10O concentration increases. The composition and thermophysical properties of pure C5F10O in the temperature range from 300 K to 2000 K based on the decomposition pathway are also given. The calculation results provide a basis for further study of the insulation and arc-quenching capability of C5F10O-CO2 gas mixtures as substitutes for SF6.

Crystallographic Study of Mixture CeBa1.8Pb0.2Cu3Oy in the Range of 860°C to 940 °C

NASA Astrophysics Data System (ADS)

Stergiou, A.; Yilmaz, S.; Stergiou, C.

2007-04-01

A powder mixture with chemical formula CeBa1.8Pb0.2Cu3Oy was prepared. The mixture was heated in free atmosphere, at temperatures 860°C to 940°C, for 24 to 72h. The samples were measured by X-Ray powder diffraction with CuKa radiation. Each sample was characterized with the help of the PDF and refined, using the Rietveld's ``Powder Profile Analysis''. The first sample (860°C) was identified with the phases: Ba2CeBiO6, CuO and BaCuO2, while all the remaining samples (870°C-940°C) with the phases Ba2CePbO6, CuO and CeO2. The phases Ba2CeBiO6 and Ba2CePbO6 are the main phases with analogous chemical types, but different symmetry. The phase CuO is common in all the samples, while from the remaining phases the BaCuO2 appears only in the first sample and the CeO2 in all, except the first one. The quantity 0.2 of Pb is distributed in the Ba positions, substituting a part of these. The percentages of phases are about 82%, 10% and 8% for the first sample and for all the remaining about 85%, 8% and 7%, respectively with above serious.

A novel metal-organic framework for high storage and separation of acetylene at room temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, Xing, E-mail: star1987@hdu.edu.cn; Wang, Huizhen; Ji, Zhenguo

2016-09-15

A novel 3D microporous metal-organic framework with NbO topology, [Cu{sub 2}(L)(H{sub 2}O){sub 2}]∙(DMF){sub 6}·(H{sub 2}O){sub 2} (ZJU-10, ZJU = Zhejiang University; H{sub 4}L =2′-hydroxy-[1,1′:4′,1″-terphenyl]-3,3″,5,5″-tetracarboxylic acid; DMF =N,N-dimethylformamide), has been synthesized and structurally characterized. With suitable pore sizes and open Cu{sup 2+} sites, ZJU-10a exhibits high BET surface area of 2392 m{sup 2}/g, as well as moderately high C{sub 2}H{sub 2} volumetric uptake capacity of 132 cm{sup 3}/cm{sup 3}. Meanwhile, ZJU-10a is a promising porous material for separation of acetylene from methane and carbon dioxide gas mixtures at room temperature. - Graphical abstract: A new NbO-type microporous metal-organic framework ZJU-10 withmore » suitable pore size and open Cu{sup 2+} sites was synthesized to realize the strong interaction with acetylene molecules, which can separate the acetylene from methane and carbon dioxane gas mixtures at room temperature. Display Omitted - Highlights: • A novel 3D NbO-type microporous metal-organic framework ZJU-10 was solvothermally synthesized and structurally characterized. • ZJU-10a exhibits high BET surface area of 2392 m{sup 2}/g. • ZJU-10a shows a moderately high C{sub 2}H{sub 2} gravimetric (volumetric) uptake capacity of 174 (132) cm{sup 3}/g at 298 K and 1 bar. • ZJU-10a can separate acetylene from methane and carbon dioxide gas mixtures at room temperature.« less

Time-dependent middle ear pressure changes under general anaesthesia in children: N2O-O2 mixture versus air-oxygen mixture.

PubMed

Apan, A; Muluk, N Bayar; Güler, S; Budak, B

2013-01-01

The aim of this study was to investigate the effects of N2O-O2 mixture (Inspired O2 30%) on middle ear pressure (MEP) in children compared with the effects of an air-oxygen mixture (Inspired O2 50%). The study included thirty child patients who underwent general anaesthesia for different reasons, with the exception of ENT problems and ear interventions. They were randomly divided into two groups. Group 1 (15 children: 10 male and 5 female) received a N2O-O2 mixture (Inspired O2 30%); and group 2 (15 children: 10 male and 5 female) were given an air-oxygen mixture (Inspired O2 50%). MEP was measured using a portable impedance analyser before the operation (PreO),10 minutes after intubation (10AEn), 30 minutes after intubation (30AEn), 10 minutes before extubation (10BEx), 15 minutes after the operation (PO15), 30 minutes after the operation (PO30), 1 hour after the operation (PO1h) and 6 hours after the operation (PO6h). The pressure and compliance values were the same in groups 1 and 2. The pressure-time graphs for the two groups were different: in Group 2, MEP rose quickly at 10AEn and positive pressure values were seen in the middle ear. MEP then fell rapidly until the end of the surgery and lower and negative pressures (Mean -50 daPa) were observed at PO6h. In Group 1, MEP was elevated at 10AEn and positive pressure was found (but not as high as in Group 2). MEP then fell more slowly. In other words, positive pressure in the middle ear persisted longer and the middle ear was subjected to positive pressure and nitrogen over a longer period. Separate analyses were made in Groups 1 and 2 of pressure differences and of compliance values at eight measurement points using the Friedman test. Differences in pressure values were found to be statistically significant in both Group 1 (p = 0.000) and Group 2 (p = 0.000). In Group 1, all the 10AEn and 30AEn values were significantly higher than the PreO, PO30, PO1h and PO6h values. The 10BEx value was significantly higher than the PreO and PO1h values. The PO15 value was significantly higher than the PreO value. In Group 2, the PO6h value was significantly lower than the 10BEx, 10AEn and 30AEn values. The PO1h value was significantly lower than the 30AEn values. The MEP values increased in Group 1 in younger and taller children and in children receiving anaesthesia for shorter periods. MEP values increased in Group 2 in younger and taller children, and in heavier children. MEP values fell with the length of anaesthesia. In brief anaesthesia, nitrogen was not removed from the middle ear quickly in Group 1: middle ear pressure values were higher. The nitrous oxide remained in the middle ear longer and so the possibility of ear toxicity may increase. In Group 2, 50% O2 was rapidly absorbed and removed from the middle ear and so middle ear pressure was not as high. It may be concluded that air-oxygen mixture (Inspired O2 50%) anaesthesia should be recommended as being more reliable in tympanoplasties and other middle ear interventions than a N2O-O2 mixture (Inspired O2 30%).

Effects of micro-water on decomposition of the environment-friendly insulating medium C5F10O

NASA Astrophysics Data System (ADS)

Xiao, Song; Li, Yi; Zhang, Xiaoxing; Tian, Shuangshuang; Deng, Zaitao; Tang, Ju

2017-06-01

SF6 is widely used in all kinds of high-voltage electrical equipment because of its excellent insulation and arc-extinguishing performance. However, this compound leads to serious greenhouse effect, which harms the environment. Many research institutions are now actively in search of SF6 alternative gas. C5F10O has attracted much attention as an alternative gas with low global warming potential (GWP) and excellent dielectric strength. In this paper, we analyzed the possible decomposition paths of C5F10O under micro-water environment through density functional theory. We also evaluated the ionization parameters and toxicity of the decomposition products. The results show that OH• and H• produced by H2O exhibited a catalytic effect on the decomposition of C5F10O. CF4, C2F6, C3F6, C3F8, C4F10, C5F12, C6F14, C3F7COH, C3F7OH, CF3COH, C3F7H, and CF3OH were produced in the micro-water environment. Based on molecular configuration calculation, the ionization parameters of these products were inferior to perfluorocarbons, such as C3F8, leading to reduced insulation performance of the system. Moreover, CF2O and HF are hazardous to human health and equipment safety. Results will provide a basis for further study of the insulation characteristic of the C5F10O gas mixture under micro-water condition to guide the formulation of their relevant international standards prior to engineering applications.

Low temperature (550-700 K) oxidation pathways of cyclic ketones: Dominance of HO 2-elimination channels yielding conjugated cyclic coproducts

DOE PAGES

Scheer, Adam M.; Welz, Oliver; Vasu, Subith S.; ...

2015-04-13

The low-temperature oxidation of three cyclic ketones, cyclopentanone (CPO; C 5H 8O), cyclohexanone (CHO; C 6H 10 O), and 2-methyl-cyclopentanone (2-Me-CPO; CH 3–C 5H7 O), is studied between 550 and 700 K and at 4 or 8 Torr total pressure. Initial fuel radicals R are formedvia fast H-abstraction from the ketones by laser-photolytically generated chlorine atoms. Intermediates and products from the subsequent reactions of these radicals in the presence of excess O 2 are probed with time and isomeric resolution using multiplexed photoionization mass spectrometry with tunable synchrotron ionizing radiation. For CPO and CHO the dominant product channel in themore » R + O 2 reactions is chain-terminating HO 2-elimination yielding the conjugated cyclic coproducts 2-cyclopentenone and 2-cyclohexenone, respectively. Results on oxidation of 2-Me-CPO also show a dominant contribution from HO 2-elimination. Moreover, the photoionization spectrum of the co-product suggests formation of 2-methyl-2-cyclopentenone and/or 2-cyclohexenone, resulting from a rapid Dowd–Beckwith rearrangement, preceding addition to O 2, of the initial (2-oxocyclopentyl)methyl radical to 3-oxocyclohexyl. Cyclic ethers, markers for hydroperoxyalkyl radicals (QOOH), key intermediates in chain-propagating and chain-branching low-temperature combustion pathways, are only minor products. The interpretation of the experimental results is supported by stationary point calculations on the potential energy surfaces of the associated R + O 2 reactions at the CBS-QB3 level. Furthermore, the calculations indicate that HO 2-elimination channels are energetically favored and product formation via QOOH is disfavored. Lastly, the prominence of chain-terminating pathways linked with HO 2 formation in low-temperature oxidation of cyclic ketones suggests little low-temperature reactivity of these species as fuels in internal combustion engines.« less

Low temperature (550-700 K) oxidation pathways of cyclic ketones: Dominance of HO 2-elimination channels yielding conjugated cyclic coproducts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheer, Adam M.; Welz, Oliver; Vasu, Subith S.

The low-temperature oxidation of three cyclic ketones, cyclopentanone (CPO; C 5H 8O), cyclohexanone (CHO; C 6H 10 O), and 2-methyl-cyclopentanone (2-Me-CPO; CH 3–C 5H7 O), is studied between 550 and 700 K and at 4 or 8 Torr total pressure. Initial fuel radicals R are formedvia fast H-abstraction from the ketones by laser-photolytically generated chlorine atoms. Intermediates and products from the subsequent reactions of these radicals in the presence of excess O 2 are probed with time and isomeric resolution using multiplexed photoionization mass spectrometry with tunable synchrotron ionizing radiation. For CPO and CHO the dominant product channel in themore » R + O 2 reactions is chain-terminating HO 2-elimination yielding the conjugated cyclic coproducts 2-cyclopentenone and 2-cyclohexenone, respectively. Results on oxidation of 2-Me-CPO also show a dominant contribution from HO 2-elimination. Moreover, the photoionization spectrum of the co-product suggests formation of 2-methyl-2-cyclopentenone and/or 2-cyclohexenone, resulting from a rapid Dowd–Beckwith rearrangement, preceding addition to O 2, of the initial (2-oxocyclopentyl)methyl radical to 3-oxocyclohexyl. Cyclic ethers, markers for hydroperoxyalkyl radicals (QOOH), key intermediates in chain-propagating and chain-branching low-temperature combustion pathways, are only minor products. The interpretation of the experimental results is supported by stationary point calculations on the potential energy surfaces of the associated R + O 2 reactions at the CBS-QB3 level. Furthermore, the calculations indicate that HO 2-elimination channels are energetically favored and product formation via QOOH is disfavored. Lastly, the prominence of chain-terminating pathways linked with HO 2 formation in low-temperature oxidation of cyclic ketones suggests little low-temperature reactivity of these species as fuels in internal combustion engines.« less

Unimolecular thermal decomposition of phenol and d5-phenol: Direct observation of cyclopentadiene formation via cyclohexadienone

NASA Astrophysics Data System (ADS)

Scheer, Adam M.; Mukarakate, Calvin; Robichaud, David J.; Nimlos, Mark R.; Carstensen, Hans-Heinrich; Barney Ellison, G.

2012-01-01

The pyrolyses of phenol and d5-phenol (C6H5OH and C6D5OH) have been studied using a high temperature, microtubular (μtubular) SiC reactor. Product detection is via both photon ionization (10.487 eV) time-of-flight mass spectrometry and matrix isolation infrared spectroscopy. Gas exiting the heated reactor (375 K-1575 K) is subject to a free expansion after a residence time in the μtubular reactor of approximately 50-100 μs. The expansion from the reactor into vacuum rapidly cools the gas mixture and allows the detection of radicals and other highly reactive intermediates. We find that the initial decomposition steps at the onset of phenol pyrolysis are enol/keto tautomerization to form cyclohexadienone followed by decarbonylation to produce cyclopentadiene; C6H5OH → c-C6H6 = O → c-C5H6 + CO. The cyclopentadiene loses a H atom to generate the cyclopentadienyl radical which further decomposes to acetylene and propargyl radical; c-C5H6 → c-C5H5 + H → HC≡CH + HCCCH2. At higher temperatures, hydrogen loss from the PhO-H group to form phenoxy radical followed by CO ejection to generate the cyclopentadienyl radical likely contributes to the product distribution; C6H5O-H → C6H5O + H → c-C5H5 + CO. The direct decarbonylation reaction remains an important channel in the thermal decomposition mechanisms of the dihydroxybenzenes. Both catechol (o-HO-C6H4-OH) and hydroquinone (p-HO-C6H4-OH) are shown to undergo decarbonylation at the onset of pyrolysis to form hydroxycyclopentadiene. In the case of catechol, we observe that water loss is also an important decomposition channel at the onset of pyrolysis.

Extending the lanthanide-terephthalate system: Isolation of an unprecedented Tb(III)-based coordination polymer with high potential porosity and luminescence properties

NASA Astrophysics Data System (ADS)

Le Natur, François; Calvez, Guillaume; Freslon, Stéphane; Daiguebonne, Carole; Bernot, Kevin; Guillou, Olivier

2015-04-01

A novel coordination polymer with chemical formula {[Tb(bdc)1.5(H2O)]ṡ(DMF)(H2O)}∞ (1) has been synthesized by reaction between 1,4-benzene-dicarboxylic acid (H2bdc) and di-cationic hexanuclear entity [Tb6O(OH)8(NO3)6(H2O)12]2+ in an ethylene glycol (EG)/N,N-dimethylformamide (DMF) mixture. This compound has been obtained as single crystals by slow evaporation in air at room temperature. If the hexanuclear entity is destroyed during the reaction, the coordination polymer that is obtained is original and presents promising potential micro-porosity and luminescent properties. It crystallizes in the monoclinic system, space group C12/c1 (No. 15) with the cell parameters a = 23.7540(1) Å, b = 10.5390(4) Å, c = 19.7580(3) Å, β = 125.8100(1)° and Z = 8.

Molecular structure and conformational composition of methyl chloroacetate: An electron-diffraction and ab initio molecular orbital investigation

NASA Astrophysics Data System (ADS)

Aarset, Kirsten; Boldermo, Kjell Gunnar; Hagen, Kolbjørn

2010-08-01

The molecular structure and conformational composition of methyl chloroacetate, H 2ClC sbnd C( dbnd O) sbnd O sbnd CH 3, have been determined by gas-phase electron-diffraction (GED), using results from ab initio molecular orbital calculations (HF, MP2 and MP3/6-311+G(d,p)) to obtain constraints on some of the structural parameters. The molecules exist in the gas-phase at 25 °C as a mixture of two stable conformers: syn with C sbnd Cl eclipsing C dbnd O and gauche with C sbnd H approximately eclipsing C dbnd O. In both of these conformers O sbnd CH 3 is also eclipsing C dbnd O. The experimentally observed conformational composition at 25 °C was 36(8)% syn and 64(8)% gauche (parenthesised values are 2 σ), corresponding to a free energy difference between conformers of ΔGexp° = 1.4(9) kJ/mol. The corresponding theoretical values obtained for Δ G° are 1.1 kJ/mol (HF), 2.3 kJ/mol (MP2), and 2.4 kJ/mol (MP3). The results for the principal distances ( rh1) and angles ( ∠h1) for the major gauche conformer obtained from the combined GED/ ab initio study (2 σ uncertainties) are r(CO sbnd CCl) = 1.502(9) Å, r(C sbnd H) = 1.084(6) Å (average value), r(C sbnd Cl) = 1.782(4) Å, r(C dbnd O) = 1.213(4) Å, r(CO sbnd O) = 1.346(4) Å, r(CH 3sbnd O) = 1.468(10) Å, ∠C sbnd C sbnd Cl = 110.0(6)°, ∠C sbnd C dbnd O = 124.7(6)°, ∠C sbnd C sbnd O = 108.3(10)°, ∠C sbnd O sbnd C = 115.9(8)°, ϕ(Cl sbnd C sbnd C dbnd O) = 111(2)°, ϕ(C sbnd O sbnd C dbnd O) = 3(3)°.

Nucleic acid component analogues: synthesis of 2'-deoxynucleosides from 5-substituted-4-hydroxy-6(1H)-pyrimidinones.

PubMed

Khattab, Ahmed F; Abdel Megied, Ahmed E S; Pedersen, Erik B

2003-01-01

Condensation of the silylated pyrimidines 5a-c with methyl 2-deoxy-3,5-di-O-toluoyl-D-pentofuranoside 6, using trimethylsilyltriflate as catalyst gave anomeric mixtures of 2'-deoxynucleosides 7a-c, the pure alpha- and beta-anomers were separated and deprotected with sodium methoxide in methanol to give 1-(2'-deoxy-alpha-D-pentafuranosyl)-4-hydroxy-5-substituted-6(1H)-pyrimidinones 10a,b and 13a and their corresponding beta-anomers 11a,b and 13b.

O2-(6-Oxocyclohex-1-en-1-yl)methyl diazen-1-ium-1,2-diolates: a new class of nitric oxide donors activatable by GSH/GSTπ with both anti-proliferative and anti-metastatic activities against melanoma.

PubMed

Bai, Chengfeng; Xue, Rongfang; Wu, Jianbing; Lv, Tian; Luo, Xiaojun; Huang, Yun; Gong, Yan; Zhang, Honghua; Zhang, Yihua; Huang, Zhangjian

2017-05-02

The new nitric oxide (NO) donor O 2 -(6-oxocyclohex-1-en-1-yl)methyl diazen-1-ium-1,2-diolate 3c could simultaneously liberate NO as well as an active 3-glutathionyl-2-exomethylene-cyclohexanone 2 in the presence of GSH/GSTπ; exhibit potent antiproliferative activity; repress migration, invasion, and lateral migration of metastatic B16-BL6 cells; and significantly decrease hetero-adhesion of B16-BL6 cells to human umbilical vein endothelial cells.

Unimolecular Thermal Decomposition of Phenol and d5-Phenol: Direct Observation of Cyclopentadiene Formation via Cyclohexadienone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheer, A. M.; Mukarakate, C.; Robichaud, D. J.

The pyrolyses of phenol and d{sub 5}-phenol (C{sub 6}H{sub 5}OH and C{sub 6}D{sub 5}OH) have been studied using a high temperature, microtubular ({mu}tubular) SiC reactor. Product detection is via both photon ionization (10.487 eV) time-of-flight mass spectrometry and matrix isolation infrared spectroscopy. Gas exiting the heated reactor (375 K-1575 K) is subject to a free expansion after a residence time in the {mu}tubular reactor of approximately 50-100 {micro}s. The expansion from the reactor into vacuum rapidly cools the gas mixture and allows the detection of radicals and other highly reactive intermediates. We find that the initial decomposition steps at themore » onset of phenol pyrolysis are enol/keto tautomerization to form cyclohexadienone followed by decarbonylation to produce cyclopentadiene; C{sub 6}H{sub 5}OH {yields} c-C{sub 6}H{sub 6} = O {yields} c-C{sub 5}H{sub 6} + CO. The cyclopentadiene loses a H atom to generate the cyclopentadienyl radical which further decomposes to acetylene and propargyl radical; c-C{sub 5}H{sub 6} {yields} c-C{sub 5}H{sub 5} + H {yields} HC {triple_bond} CH + HCCCH{sub 2}. At higher temperatures, hydrogen loss from the PhO-H group to form phenoxy radical followed by CO ejection to generate the cyclopentadienyl radical likely contributes to the product distribution; C{sub 6}H{sub 5}O-H {yields} C{sub 6}H{sub 5}O + H {yields} c-C{sub 5}H{sub 5} + CO. The direct decarbonylation reaction remains an important channel in the thermal decomposition mechanisms of the dihydroxybenzenes. Both catechol (o-HO-C{sub 6}H{sub 4}-OH) and hydroquinone (p-HO-C{sub 6}H{sub 4}-OH) are shown to undergo decarbonylation at the onset of pyrolysis to form hydroxycyclopentadiene. In the case of catechol, we observe that water loss is also an important decomposition channel at the onset of pyrolysis.« less

A study of nonflammable ArCO 2-hydrocarbon gas mixtures for limited streamer tubes

NASA Astrophysics Data System (ADS)

Cartwright, S.; Schneekloth, U.; Alpat, B.; Artemi, C.; Battiston, R.; Bilei, G.; Italiani, M.; Pauluzzi, M.; Servoli, L.; Messner, R.; Wyss, J.; Zdarko, R.; Johnson, J.

1989-04-01

The gas mixtures generally used until now in limited streamer tube detectors (Ar+C 4H 10 or Ar+CO 2+C 5H 12) are very flammable when leaked into air. The safety issues are therefore very relevant for large-volume underground experiments. We have found a set of completely safe (i.e. nonflammable) ternary mixtures of the kind Ar + hydrocarbon + CO 2 containing less than ˜ 5% of Ar and less than ˜ 10% of hydrocarbon. We tested C 4H 10, C 5H 12 and C 6H 14 as quenching agents. The main characteristics of the various mixtures have been measured: singles (untriggered) counting rate versus high voltage and with different dead times, and average charge. The stability of these mixtures is good, and their spurious streamer activity is compared with the standard binary or ternary mixture. We studied in particular the combination Ar(2.5%) + C 4H 10(9.5%) + CO 2(88%). All the data suggest that this or a similar gas mixture can successfully replace standard flammable mixtures both in tracking devices and hadron calorimeters.

Laboratory Analysis Of Water, Hydrocarbon And Ammonia Ice Mixtures Exposed To High-energy Electron Irradiation

NASA Astrophysics Data System (ADS)

Hand, Kevin P.; Carlson, R. W.; Tsapin, A. I.

2006-09-01

Irradiation of low temperature ices in the laboratory provides insight into processes that may be occurring on icy bodies in the solar system. Here we report on results from high-energy (10keV) electron irradiation of thin ice films at 1e-8 torr and 70-120K. Mixtures include water with CO2, C3H8, C3H6, C4H10 (butane and isobutane), C4H8,(1-butene and cis/trans-2-butene), and NH3. During irradiation of H2O + alkane films at 80K, CO2 and CH4 production is observed and both species are retained in the ice, possibly trapped in clathrates. The -CH3 infrared bands initially present are seen to decrease with increasing dose. Bands associated with -CH2- persist, indicating polymerization of the initial short-chain hydrocarbons. In alkenes a similar evolution toward polymerization is observed, however the first step appears to be the destruction of the C=C bond. Upon warming of the film, mass spectra data compliment the mid-infrared data and indicate the production of H2CO, however glycolic acid is not explicitly seen in the mass spectra. When warmed to 300K, residues remained for all irradiated films except that of the H2O + CO2 mixtures. Residues were analyzed with Matrix Assisted Laser Desorption/Ionization Mass Spectrometry (MALDI). Results show the production of large aliphatic, very refractory, hydrocarbons (with m/z up to 2500). Mid-infrared spectra of the residues indicate carbonyls and alcohols, likely due to polymerized aldehydes and carboxylic acids. Films of H2O + C3H8 + NH3 at 70K show the production of OCN- (cyanate ion), formamide, along with other possible amides and hydrocarbons. HPLC results indicate the production of racemic alanine. Finally, results of abiotic experiments are compared to results from the irradiation of bacterial spores in ice. The application to Europa and Enceladus is discussed.

A New Green Chemical Synthesis Strategy for Synthesis of L10 FePt Nanoparticles from Layered Precursor Fe(H2O)6PtCl6

NASA Astrophysics Data System (ADS)

Hadjipanayis, George; Hu, Xiaocao; Capobianchi, Aldo; Gallagher, Ryan

2014-03-01

In this work, a new green chemical strategy for the synthesis of L10 FePt nanoparticles is reported. The starting material is a polycrystalline molecular complex (Fe(H2O)6PtCl6) , in which Fe and Pt atoms are arranged on alternating planes. The starting compound was milled with crystalline NaCl and then annealed under forming gas (5 % H2 and 95 % Ar) at 450 °C for 2h. Finally, the mixture was washed with water to remove the NaCl and L10 FePt nanoparticles were obtained. Transmission electron microscopy (TEM) images revealed that this method is able to produce L10 nanoparticles with different average size varying from 13.9 nm to 5.4 nm depending on the (Fe(H2O)6PtCl6) /NaCl ratio. With smaller (Fe(H2O)6PtCl6) /NaCl ratio(10mg/20g) and longer milling time(15h), FePt nanoparticles had a smaller size and narrower size distribution. The X-Ray Diffraction (XRD) pattern showed the presence of the characteristic peaks of the fct phase. The hysteresis loop, measured both at room temperature and 50 K, shows a high coercivity of 7.6 kOe and 11.2 kOe, respectively as expected for the high anisotropy L10 phase. Larger precursor/NaCl ratio and shorter ball milling time led to larger coercivity.

Laser-deposited thin films of biocompatible ceramic

NASA Astrophysics Data System (ADS)

Jelinek, Miroslav; Olsan, V.; Jastrabik, Lubomir; Dostalova, Tatjana; Himmlova, Lucia; Kadlec, Jaromir; Pospichal, M.; Simeckova, M.; Fotakis, Costas

1995-03-01

Thin films of biocompatible materials such as hydroxylapatite (HA) - Ca10 (PO4)6(OH)2 were deposited by laser ablation technique. The films of HA were created on Ti substrates by KrF laser. The layers were deposited in vacuum, in pure H2O vapors (pressure 2 X 10-3 mbar - 2 X 10-1 mbar), and in Ar/H2O vapor mixture. Influence of laser energy density ET (3 Jcm-2, 13 Jcm-2) and substrate temperature Tg (500 degree(s)C - 760 degree(s)C) on the film parameters was studied. Two different technological processes were used for HA target preparation. Films and targets were characterized by Rutherford backscattering analysis (RBS), particle induced x-ray emission (PIXE), x-ray diffraction (XRD), scanning electron microscopy (SEM) and by Knoop microhardness and scratch test. The best crystalline HA films were reached in the mixture of Ar/H2O. Higher Tg had to be used for such deposition. Higher Tg was also preferable from the point of film microhardness. Adhesion of films to the substrates in the range of tens of Newtons was measured. The preliminary results of in vitro experiments of films biotolerance and resorbability are also presented.

Highly efficient alkane oxidation catalyzed by [Mn(V)(N)(CN)4](2-). Evidence for [Mn(VII)(N)(O)(CN)4](2-) as an active intermediate.

PubMed

Ma, Li; Pan, Yi; Man, Wai-Lun; Kwong, Hoi-Ki; Lam, William W Y; Chen, Gui; Lau, Kai-Chung; Lau, Tai-Chu

2014-05-28

The oxidation of various alkanes catalyzed by [Mn(V)(N)(CN)4](2-) using various terminal oxidants at room temperature has been investigated. Excellent yields of alcohols and ketones (>95%) are obtained using H2O2 as oxidant and CF3CH2OH as solvent. Good yields (>80%) are also obtained using (NH4)2[Ce(NO3)6] in CF3CH2OH/H2O. Kinetic isotope effects (KIEs) are determined by using an equimolar mixture of cyclohexane (c-C6H12) and cyclohexane-d12 (c-C6D12) as substrate. The KIEs are 3.1 ± 0.3 and 3.6 ± 0.2 for oxidation by H2O2 and Ce(IV), respectively. On the other hand, the rate constants for the formation of products using c-C6H12 or c-C6D12 as single substrate are the same. These results are consistent with initial rate-limiting formation of an active intermediate between [Mn(N)(CN)4](2-) and H2O2 or Ce(IV), followed by H-atom abstraction from cyclohexane by the active intermediate. When PhCH2C(CH3)2OOH (MPPH) is used as oxidant for the oxidation of c-C6H12, the major products are c-C6H11OH, c-C6H10O, and PhCH2C(CH3)2OH (MPPOH), suggesting heterolytic cleavage of MPPH to generate a Mn═O intermediate. In the reaction of H2O2 with [Mn(N)(CN)4](2-) in CF3CH2OH, a peak at m/z 628.1 was observed in the electrospray ionization mass spectrometry, which is assigned to the solvated manganese nitrido oxo species, (PPh4)[Mn(N)(O)(CN)4](-)·CF3CH2OH. On the basis of the experimental results the proposed mechanism for catalytic alkane oxidation by [Mn(V)(N)(CN)4](2-)/ROOH involves initial rate-limiting O-atom transfer from ROOH to [Mn(N)(CN)4](2-) to generate a manganese(VII) nitrido oxo active species, [Mn(VII)(N)(O)(CN)4](2-), which then oxidizes alkanes (R'H) via a H-atom abstraction/O-rebound mechanism. The proposed mechanism is also supported by density functional theory calculations.

Mössbauer study of metallic iron and iron oxide nanoparticles having environmental purifying ability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kubuki, Shiro, E-mail: kubuki@tmu.ac.jp; Watanabe, Yuka, E-mail: kubuki@tmu.ac.jp; Akiyama, Kazuhiko, E-mail: kubuki@tmu.ac.jp

2014-10-27

A relationship between local structure and methylene blue (MB) decomposing ability of nanoparticles (NPs) of metallic iron (Fe{sup 0}) and maghemite (γ‐Fe{sub 2}O{sub 3}) was investigated by {sup 57}Fe Mössbauer spectroscopy, X-ray diffractometry and UV-visible light absorption spectroscopy. γ‐Fe{sub 2}O{sub 3} NPs were successfully prepared by mixing (NH{sub 4}){sub 2}Fe(SO{sub 4}){sub 2}⋅6H{sub 2}O (Mohr's salt) and (NH{sub 4}){sub 3}Fe(C{sub 2}O{sub 4}){sub 3}⋅3H{sub 2}O aqueous solution at 30 °C for 1 h, while those of Fe{sup 0} were obtained by the reduction of Mohr's salt with NaBH{sub 4}. From the Scherrer's equation, the smallest crystallite sizes of γ‐Fe{sub 2}O{sub 3} NPsmore » and Fe{sup 0} NPs were determined to be 9.7 and 1.5 nm, respectively. {sup 57}Fe Mössbauer spectrum of γ‐Fe{sub 2}O{sub 3} NPs consists of a relaxed sextet with isomer shift (δ) of 0.33{sub ±0.01} mm s{sup −1}, internal magnetic field (H{sub int}) of 25.8{sub ±0.5} T, and linewidth (Γ) of 0.62{sub ±0.04} mm s{sup −1}. {sup 57}Fe Mössbauer spectrum of Fe{sup 0} NP is mainly composed of a sextet having δ, Δ, and H{sub int} of 0.00{sub ±0.01} mm s{sup −1} 0.45{sub ±0.01} mm s{sup −1}, and 22.8{sub ±0.1} T, respectively. A bleaching test of the mixture of Fe{sup 0} and γ‐Fe{sub 2}O{sub 3} NPs (3:7 ratio, 100 mg) in MB aqueous solution (20 mL) for 6 h showed a remarkable decrease of MB concentration with the first-order rate constant (k{sub MB}) of 6.7 × 10{sup −1} h{sup −1}. This value is larger than that obtained for the bleaching test using bulk Fe{sup 0}+γ‐Fe{sub 2}O{sub 3} (3:7) mixture (k{sub MB} = 6.5×10{sup −3}h{sup −1}). These results prove that MB decomposing ability is enhanced by the NPs mixture of Fe{sub 0} and γ‐Fe{sub 2}O{sub 3}.« less

Identification of polymethoxylated flavones from green tangerine peel (Pericarpium Citri Reticulatae Viride) by chromatographic and spectroscopic techniques.

PubMed

Wang, Dandan; Wang, Jian; Huang, Xuehui; Tu, Ying; Ni, Kunyi

2007-05-09

Polymethoxylated flavones (PMFs) were extracted from Pericarpium Citri Reticulatae Viride using a procedure that obtained a consistent mixture of PMFs both in identity and proportion. The mixture consisted of isosinensetin (0.2%) (1), sinensetin (1.7%) (4), tetramethyl-o-isoscutellarein (0.3%) (5), nobiletin (40.5%) (6), tetramethyl-o-scutellarein (1.2%) (7), tangeretin (45.6%) (10), 5-demethylnobiletin (8.7%) (12), 5-demethyl tangeretin (0.8%) (14) and other flavonoids including heptamethoxyflavone (1.0%) (9), among which, compounds 1, 4, 5, 7 and 9 were identified based on their UV spectra, MS data and elution order described in the literature while compounds 6, 10, 12 and 14 were isolated and identified by UV, IR, MS, (1)H NMR, (13)C NMR and 2D NMR spectral studies. In addition, compound 14 was isolated and identified for the first time from Citrus.

Development of a process for the extraction of {sup 137}Cs from acidic HLLW based on crown-calix extractant use of di-alkylamide modifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexova, J.; Sirova, M.; Rais, J.

2008-07-01

Within the framework of the ARTIST project of total fuel retreatment with ecological mixtures of solvents and extractants containing only C, H, O, and N atoms, a process segment of extraction of {sup 137}Cs from acidic stream was developed. The process with 25,27-Bis(1-octyloxy)calix[4]arene-crown- 6, DOC[4]C6, dissolved at its 0.01 M concentration in a mixture of 90 vol % 1-octanol and 10% dihexyl octanamide, DHOA was proposed as a viable variant due to its good multicycle performance, even with irradiated solvent, and due to the good chemical stability of the chosen combination of solvent mixture. (authors)

Mechanism of thermal electron attachment in N/sub 2/O--CO/sub 2/ mixtures in the gas phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shimamori, H.; Fessenden, R.W.

1978-12-01

The attachment of thermal electrons to nitrous oxide in N/sub 2/O--CO/sub 2/ mixtures has been studied at room temperature in the pressure range 5--120 torr. Ionization was by pulse radiolysis and the electron concentration was measured as a function of time by microwave conductivity. Addition of even less than 0.1% CO/sub 2/ to N/sub 2/O causes a marked increase in attachment rate. However, this enhancement soon saturates in that further additions of CO/sub 2/ have less and less effect. Experiments with ternary mixtures including C/sub 2/H/sub 6/ showed a further enhancement which was much larger than the additive effects ofmore » CO/sub 2/ and C/sub 2/H/sub 6/ alone. These observations can be explained by a two step three-body process producing vibrationally excited N/sub 2/O/sup -/* if the rate constant for stabilization of N/sub 2/O/sup -/* by CO/sub 2/ is 4 x 10/sup -30/ cm/sup 6//molecule/sup 2/xsec. The decrease in effectiveness with increased CO/sub 2/ pressure is interpreted as the collisional ionization of a complex ion, (N/sub 2/OxCO/sub 2/)/sup -/*. The nonadditive effect of hydrocarbon results from the rapid reactive destruction of such complexes by collision with the hydrocarbon. A detailed quantitative treatment of the proposed mechanism was successful in explaining most features of the data. In a limited set of experiments, allene : N/sub 2/O mixtures were found to behave much like CO/sub 2/--N/sub 2/O.« less

Palladium-Catalyzed Formal Cross-Coupling of Diaryl Ethers with Amines: Slicing the 4-O-5 Linkage in Lignin Models.

PubMed

Zeng, Huiying; Cao, Dawei; Qiu, Zihang; Li, Chao-Jun

2018-03-26

Lignin is the second most abundant organic matter on Earth, and is an underutilized renewable source for valuable aromatic chemicals. For future sustainable production of aromatic compounds, it is highly desirable to convert lignin into value-added platform chemicals instead of using fossil-based resources. Lignins are aromatic polymers linked by three types of ether bonds (α-O-4, β-O-4, and 4-O-5 linkages) and other C-C bonds. Among the ether bonds, the bond dissociation energy of the 4-O-5 linkage is the highest and the most challenging to cleave. To date, 4-O-5 ether linkage model compounds have been cleaved to obtain phenol, cyclohexane, cyclohexanone, and cyclohexanol. The first example of direct formal cross-coupling of diaryl ether 4-O-5 linkage models with amines is reported, in which dual C(Ar)-O bond cleavages form valuable nitrogen-containing derivatives. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dynamics of Nafion membrane swelling in H2O/D2O mixtures as studied using FTIR technique

NASA Astrophysics Data System (ADS)

Bunkin, Nikolai F.; Kozlov, Valeriy A.; Shkirin, Alexey V.; Ninham, Barry W.; Balashov, Anatoliy A.; Gudkov, Sergey V.

2018-03-01

Experiments with Fourier transform spectrometry of Nafion, a water-swollen polymeric membrane, are described. The transmittance spectra of liquid samples and Nafion, soaked in these samples, were studied, depending on the deuterium content in water in the spectral range 1.8-2.15 μm. The experiments were carried out using two protocols: in the first protocol we studied the dynamics of Nafion swelling in H2O + D2O mixtures for the deuterium concentrations 3 < C < 104 ppm, and in the second protocol we studied the dynamics of swelling in pure heavy water (C = 106 ppm). For liquid mixtures in the concentration range 3 < C < 104 ppm, the transmittance spectra are the same, but for Nafion soaked in these fluids, the corresponding spectra are different. It is shown that, in the range of deuterium contents C = 90-500 ppm, the behavior of transmittance of the polymer membrane is non-monotonic. In experiments using the second protocol, the dynamics of diffusion replacement of residual water, which is always present in the bulk of the polymer membrane inside closed cavities (i.e., without access to atmospheric air), were studied. The experimentally estimated diffusion coefficient for this process is ≈6.10-11 cm2/s.

Phase Equilibria and Transport Properties in the Systems AgNO3/RCN/H2O. R = CH3, C2H5, C3H7, C4H,, C6H5, and C6H5CH2

NASA Astrophysics Data System (ADS)

Das, Surjya P.; Wittekopf, Burghard; Weil, Konrad G.

1988-11-01

Silver nitrate can form homogeneous liquid phases with some organic nitriles and water, even when there is no miscibility between the pure liquid components. We determined the shapes of the single phase regions in the ternary phase diagram for the following systems: silver nitrate /RCN /H2O with R =CH3, C3H7, C6H5, and C6H5CH2 at room temperature and for R =C6H5 also at 60 °C and O °C. Furthermore we studied kinematic viscosities, electrical conductivities, and densities of mixtures containing silver nitrate, RCN, and water with the mole ratios X /4 /1 (0.2≦ X ≦S 3.4). In these cases also R = C2H5 and C4H9 were studied. The organic nitriles show different dependences of viscosity and conductivity on the silver nitrate content from the aliphatic ones.

Compound I formation in artichoke (Cynara scolymus L.) peroxidase is modulated by the equilibrium between pentacoordinated and 6-aquo hexacoordinated forms of the heme and by calcium ions.

PubMed

Hiner, Alexander N P; Sidrach, Lara; Chazarra, Soledad; Varón, Ramón; Tudela, José; García-Cánovas, Francisco; Rodríguez-López, José Neptuno

2003-07-29

Basic artichoke (Cynara scolymus L.) peroxidase (AKP-C), when purified from the plant, has an unusually intense and sharp Soret absorption peak. The resonance Raman spectrum [López-Molina, D., et al. (2003) J. Inorg. Biochem. 94, 243-254] suggested a mixture of pentacoordinate high-spin (5cHS) and 6-aquo hexacoordinate high-spin (6cHS) ferric heme species. The rate constant (k(1)) of compound I formation with hydrogen peroxide (H(2)O(2)) was also lower than expected. Further stopped-flow studies have shown this reaction to be biphasic: a nonsaturating fast phase and a slow phase with complex H(2)O(2) concentration dependence. Addition of calcium ions (Ca(2+)) changed the absorption spectrum, suggesting the formation of a fully 5cHS species with a k(1) more than 5 orders of magnitude greater than that in the absence of Ca(2+) using the chelator ethylenediaminetetraacetic acid. Ca(2+) titrations gave a dissociation constant for a single Ca(2+) of approximately 20 microM. The circular dichroism spectrum of AKP-C was not significantly altered by Ca(2+), indicating that any structural changes will be minor, but removal of Ca(2+) did suppress the alkaline transition between pH 10 and 11. A kinetic analysis of the reaction of Ca(2+)-free AKP-C with H(2)O(2) supports an equilibrium between a slow-reacting 6cHS form and a more rapidly reacting 5cHS species, the presence of which was confirmed in nonaqueous solution. AKP-C, as purified, is a mixture of Ca(2+)-bound 5cHS, 6-aquo 6cHS, and Ca(2+)-free 5cHS species. The possibility that Ca(2+) concentration could control peroxidase activity in the plant is discussed.

Heat resistant polymers of oxidized styrylphosphine

NASA Technical Reports Server (NTRS)

Paciorek, K. J. L. (Inventor)

1980-01-01

A flame resistant, nontoxic polymer which may be used safely in confined locations where there is inadequate ventilation is prepared either by polymerizing compounds having the formula R-N=P(C6H5)2(C6H4)CH=CH2 where R is an organic moeity selected from the group of (C6H5)2P(O)-, (C6H5O)2P(O)-, (C6H5)2 C3N3-, or their mixtures, or by reacting a polymer with an organic azide such as diphenylphosphinylazide, diphenyl-phosphorylazide, 2-azido-4,6-diphenly-5-triazine, 2,4-diazido-6-phenyl-s-triazine, trimethylsilyoazide, triphenylsilylazine, and phenylazine. The reaction of the styrylphosphine with the organozaide results in the oxidation of the trivalent phosphorus atom to the pentavalent state in the form of an unsaturated P=N linkage known as a phosphazene group.

Synthesis and Magnetic Properties of Ni-DOPED ZnO Thin Films: Experimental and AB INITIO Study

NASA Astrophysics Data System (ADS)

Rouchdi, M.; Salmani, E.; Hat, A. El; Hassanain, N.; Mzerd, A.

Structural and magnetic properties of Zn1-xNixO thin films and diluted magnetic semiconductors have been investigated. This sample has been synthesized using a spray pyrolysis technique with a stoechiometric mixture of zinc acetate (C4H6O4Znṡ2H2O) and Nickel acetate (C4H6O4Niṡ 2H2O) on a heated glass substrate at 450∘C. The films were characterized by X-ray diffraction (XRD), UV-Vis spectrophotometry and Hall Effect measurements. These films of ZnO crystallized in the hexagonal Wurtzite structure. The optical study showed that the band-gap energy was increased, from 3.3eV to 3.5eV, with increasing the Ni concentration. The film resistivity was affected by Ni-doping, and the best resistivity value 1.15×10-2 (Ω cm) was obtained for the film doped with 2 at.% Ni. The electronic structure and optical properties of the Wurtzite structure Zn1-xNixO were obtained by first-principles calculations using the Korringa-Kohn-Rostoker method combined with the coherent potential approximation (CPA), as well as CPA confirm our results.

ION IRRADIATION OF ETHANE AND WATER MIXTURE ICE AT 15 K: IMPLICATIONS FOR THE SOLAR SYSTEM AND THE ISM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barros, A. L. F. de; Silveira, E. F da; Fulvio, D.

2016-06-20

Solid water has been observed on the surface of many different astronomical objects and is the dominant ice present in the universe, from the solar system (detected on the surface of some asteroids, planets and their satellites, trans-Neptunian objects [TNOs], comets, etc.) to dense cold interstellar clouds (where interstellar dust grains are covered with water-rich ices). Ethane has been detected across the solar system, from the atmosphere of the giant planets and the surface of Saturn’s satellite Titan to various comets and TNOs. To date, there were no experiments focused on icy mixtures of C{sub 2}H{sub 6} and H{sub 2}Omore » exposed to ion irradiation simulating cosmic rays, a case study for many astronomical environments in which C{sub 2}H{sub 6} has been detected. In this work, the radiolysis of a C{sub 2}H{sub 6}:H{sub 2}O (2:3) ice mixture bombarded by a 40 MeV{sup 58}Ni{sup 11+} ion beam is studied. The chemical evolution of the molecular species existing in the sample is monitored by a Fourier transform infrared spectrometer. The analysis of ethane, water, and molecular products in solid phase was performed. Induced chemical reactions in C{sub 2}H{sub 6}:H{sub 2}O ice produce 13 daughter molecular species. Their formation and dissociation cross sections are determined. Furthermore, atomic carbon, oxygen, and hydrogen budgets are determined and used to verify the stoichiometry of the most abundantly formed molecular species. The results are discussed in the view of solar system and interstellar medium chemistry. The study presented here should be regarded as a first step in laboratory works dedicated to simulate the effect of cosmic radiation on multicomponent mixtures involving C{sub 2}H{sub 6} and H{sub 2}O.« less

Isolation of homoleptic platinum oxyanionic complexes with doubly protonated diazacrown cation

NASA Astrophysics Data System (ADS)

Vasilchenko, Danila; Tkachev, Sergey; Baidina, Iraida; Romanenko, Galina; Korenev, Sergey

2017-02-01

Doubly protonated diazacrown ether cation (1,4,10,13-tetraoxa-7,16-diazoniacyclooctadecane DCH22+) was used for the efficient isolation of the homoleptic platinum complexes [Pt(NO3)6]2- and [Pt(C2O4)2]2- to crystalline solid phases from solutions containing mixtures of related platinum complexes. DCH22+ molecules in nitric acid solution were shown to prevent the condensation of mononuclear [Pt(H2O)n(NO3)6-n]n-2 species.

Evaluation of consumer-style cooking methods for reduction of Escherichia coli O157:H7 in ground beef.

PubMed

Rhee, Min-Suk; Lee, Sun-Young; Hillers, Virginia N; McCurdy, Sandra M; Kang, Dong-Hyun

2003-06-01

The objective of this study was to evaluate the thermal inactivation of Escherichia coli O157:H7 in ground beef cooked to an internal temperature of 71.1 degrees C (160 degrees F) under conditions simulating consumer-style cooking methods. To compare a double-sided grill (DSG) with a single-sided grill (SSG), two different cooking methods were used for the SSG: for the one-turnover (OT-SSG) method, a patty was turned once when the internal temperature reached 40 degrees C, and for the multiturnover (MT-SSG) method, a patty was turned every 30 s. Patties (100 g, n = 9) inoculated with a five-strain mixture of E. coli O157: H7 at a concentration of 10(7) CFU/g were cooked until all three temperature readings (for two sides and the center) for a patty were 71.1 degrees C. The surviving E. coli O157:H7 cells were enumerated on sorbitol MacConkey (SMAC) agar and on phenol red agar base with 1% sorbitol (SPRAB). The order of the cooking methods with regard to the cooking time required for the patty to reach 71.1 degrees C was as follows: DSG (2.7 min) < MT-SSG (6.6 min) < OT-SSG (10.9 min). The more rapid, higher-temperature cooking method was more effective (P < 0.01) in destroying E. coli O157:H7 in ground beef. E. coli O157:H7 reduction levels were clearly differentiated among treatments as follows: OT-SSG (4.7 log10 CFU/g) < MT-SSG (5.6 log10 CFU/g) < DSG (6.9 log10 CFU/g). Significantly larger numbers of E. coil O157:H7 were observed on SPRAB than on SMAC agar. To confirm the safety of ground beef cooked to 71.1 degrees C, additional patties (100 g, n = 9) inoculated with lower concentrations of E. coli O157:H7 (10(3) to 10(4) CFU/g) were tested. The ground beef cooked by the OT-SSG method resulted in two (22%) of nine samples testing positive after enrichment, whereas no E. coli O157:H7 was found for samples cooked by the MT-SSG and DSG methods. Our findings suggest that consumers should be advised to either cook ground beef patties in a grill that cooks the top and the bottom of the patty at the same time or turn patties frequently (every 30 s) when cooking on a grill that cooks on only one side.

Catalysts for synthesizing various short chain hydrocarbons

DOEpatents

Colmenares, Carlos

1991-01-01

Method and apparatus (10), including novel photocatalysts, are disclosed for the synthesis of various short chain hydrocarbons. Light-transparent SiO.sub.2 aerogels doped with photochemically active uranyl ions (18) are fluidized in a fluidized-bed reactor (12) having a transparent window (16), by hydrogen and CO, C.sub.2 H.sub.4 or C.sub.2 H.sub.6 gas mixtures (20), and exposed to radiation (34) from a light source (32) external to the reactor (12), to produce the short chain hydrocarbons (36).

Compositions, thermodynamic properties, and transport coefficients of high-temperature C5F10O mixed with CO2 and O2 as substitutes for SF6 to reduce global warming potential

NASA Astrophysics Data System (ADS)

Zhong, Linlin; Rong, Mingzhe; Wang, Xiaohua; Wu, Junhui; Han, Guiquan; Han, Guohui; Lu, Yanhui; Yang, Aijun; Wu, Yi

2017-07-01

C5F10O has recently been found to be a very promising alternative to SF6. This paper is devoted to the investigation of compositions, thermodynamic properties, and transport coefficients of high-temperature C5F10O mixed with CO2 and O2. Firstly, the partition functions and enthalpies of formation for a few molecules (CxFy and CxFyO) which are likely to exist in the mixtures, are calculated based on the G4(MP2) theory. The isomers of the above molecules are selected according to their Gibbs energy. The compositions of C5F10O-CO2-O2 mixtures are then determined using the minimization of the Gibbs free energy. Next, the thermodynamic properties (mass density, specific enthalpy, and specific heat) are derived from the previously calculated compositions. Lastly, the transport coefficients (electrical conductivity, viscosity, and thermal conductivity) are calculated based on Chapman-Enskog method. It is found that, as an arc quenching gas, C5F10O could not recombine into itself with the temperature decreasing down to room temperature after the arc extinction. Besides, the key species at room temperature are always CF4, CO2, and C4F6 if graphite is not considered. When taken into account, graphite will replace C4F6 as one of the dominate particles. The mixing of CO2 with C5F10O plasma significantly affects the thermodynamic properties (e.g. vanishing and/or shifting of the peaks in specific heat) and transport coefficients (e.g. reducing viscosity and changing the number of peaks in thermal conductivity), while the addition of O2 with C5F10O-CO2 mixtures has no remarkable influence on both thermodynamic and transport properties.

Novel passivation dielectrics-The boron- or phosphorus-doped hydrogenated amorphous silicon carbide films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, C.Y.; Fang, Y.K.; Huang, C.F.

1985-02-01

Hydrogenated amorphous silicon carbide (a-SiC:H) thin films were prepared and studied in a radiofrequency glowdischarge system, using a gas mixture of SiH/sub 4/ and one of the following carbon sources: methane (CH/sub 4/), benzene (C/sub 6/H/sub 6/), toluene (C/sub 7/H/sub 8/), sigma-xylene (C/sub 8/H/sub 10/), trichloroethane (C/sub 2/H/sub 3/Cl/sub 3/), trichloroethylene (C/sub 2/HCl/sub 3/), or carbon tetrachloride (CCl/sub 4/). The effect of doping phosphorus and boron into those a-SiC:H films on chemical etching rate, electrica dc resistivity, breakdown strength, and optical refractive index have been systematically investigated. Their chemical etching properties were examined by immersing in 49% HF, buffered HF,more » 180/sup 0/C H/sub 3/PO/sub 4/ solutions, or in CF/sub 4/ + O/sub 2/ plasma. It was found that the boron-doped a-SiC:H film possesses five times slower etching rate than the undoped one, while phosphorus-doped a-SiC:H film shows about three times slower. Among those a-SiC:H films, the one obtained from a mixture of SiH/sub 4/ and benzene shows the best etch-resistant property, while the ones obtained from a mixture of SiH/sub 4/ and chlorine containing carbon sources (e.g., trichloroethylene, trichloroethane, or carbon tetrachloride) shows that they are poor in etching resistance (i.e., the etching rate is higher). By measuring dc resistivity, dielectric breakdown strength, and effective refractive index, it was found that boron- or phosphorus-doped a-SiC:H films exhibit much higher dielectric strength and resistivity, but lower etching rate, presumably because of higher density.« less

The Synthesis and Study of New Ribavirin Derivatives and Related Nucleoside Azole Carboxamides as Agents Active against RNA Viruses.

DTIC Science & Technology

1981-09-01

No other nucleoside product was detected. 26 When 4 was subjected to hydrogenation 3 7 with Pd/C (10%), a mixture of products was obtained even after...prolonged reduction. O2N N 02JC> ______H2 N A 3 PtO 2 0 Bz • + SzO 08 45 BOBz 3 NaOEt NH 3 O2N N N2H4H 2N N N NNN No O NO ON 6 7 The major product was...1,2,4-triazole. The minor product was found to be 3-amino-l-(2,3,3-tri-O-benzovl- 8-D-ribofuranosyl)-l,2,4-triazole (5, BJ-91120). In an effort to improve

Sesquiterpenes from Curcuma wenyujin with their inhibitory activities on nitric oxide production in RAW 264.7 cells.

PubMed

Gao, Suyu; Xia, Guiyang; Wang, Liqing; Zhou, Li; Zhao, Feng; Huang, Jian; Chen, Lixia

2017-03-01

One new sesquiterpene, 7α,11-epoxy-6α-hydroxy-carabrane-4,8-dione, along with 10 known ones were isolated from the essential oil of Curcuma wenyujin Y.H. Chen et C. Ling. Their structures were established based on extensive spectroscopic analysis. The absolute configuration of compound 1 was determined by the CD analysis of the insitu formed [Rh 2 (OCOCF 3 ) 4 ] complex, and the CD data analysis based on the octane rule of cyclohexanone. The inhibitory effects of these sesquiterpenes on nitric oxide production in lipopolysaccharide-activated macrophages were also evaluated. Furthermore, the biosynthesis pathway of the isolated compounds was proposed.

Mesoporous MnCeO x solid solutions for low temperature and selective oxidation of hydrocarbons

DOE PAGES

Zhang, Pengfei; Lu, Hanfeng; Zhou, Ying; ...

2015-10-15

The development of noble-metal-free heterogeneous catalysts that can realize the aerobic oxidation of C–H bonds at low temperature is a profound challenge in the catalysis community. Here we report the synthesis of a mesoporous Mn 0.5Ce 0.5O x solid solution that is highly active for the selective oxidation of hydrocarbons under mild conditions (100–120 °C). Notably, the catalytic performance achieved in the oxidation of cyclohexane to cyclohexanone/cyclohexanol (100 °C, conversion: 17.7%) is superior to those by the state-of-art commercial catalysts (140–160 °C, conversion: 3-5%). Finally, the high activity can be attributed to the formation of a Mn 0.5Ce 0.5O xmore » solid solution with an ultrahigh manganese doping concentration in the CeO 2 cubic fluorite lattice, leading to maximum active surface oxygens for the activation of C–H bonds and highly reducible Mn 4+ ions for the rapid migration of oxygen vacancies from the bulk to the surface.« less

Infrared matrix-isolation and theoretical studies of the reactions of ferrocene with ozone.

PubMed

Kugel, Roger W; Pinelo, Laura F; Ault, Bruce S

2015-03-19

The reactions between ferrocene (Cp2Fe) (2a) and ozone (O3) were studied using low-temperature matrix-isolation techniques coupled with theoretical density functional theory (DFT) calculations. Co-deposition of Ar/Cp2Fe and Ar/O3 gas mixtures onto a cryogenically cooled CsI window produced a dark-green charge-transfer complex, Cp2Fe-O3, that photodecomposed upon red (λ ≥ 600 nm) and infrared (λ ≥ 1000 nm) irradiation but was stable to green or blue irradiation. Products of photodecomposition were characterized by FT-IR, oxygen-18 labeling, and DFT calculations using the B3LYP functionals and the 6-311G++(d,2p) basis set. Likely, photochemical products included four structures having the molecular formula C10H10FeO, identified by DFT calculations based on their calculated infrared spectra and (18)O isotope shifts. Each of these calculated molecules had one intact and fully coordinated η(5)-C5H5 cyclopentadienyl (Cp) ring and (1) an η(5)-C5H5O cyclic ether (pyran ring) (2b), (2) an η(4)-C5H5O linear aldehyde (2c), (3) a bidentate cyclic aldehyde with a seven-membered ring including the iron atom (2d), or (4) an Fe-O bond and an η(2)-C5H5 (Cp) ring (2e). No conclusive evidence for a gas-phase thermal reaction between ferrocene and ozone was observed under the conditions of these experiments. However, strong evidence for a surface-catalyzed thermal reaction was observed in merged-jet experiments wherein the gases were premixed before deposition. Surface-catalyzed ferrocene-ozone reaction products included a thin film of Fe2O3 observed on the walls of the merged tube as well as cyclopentadiene (C5H6), cyclopentadienone (C5H4O), and further oxidation products observed in the matrix. Possible mechanisms for both the photochemical and the thermal reactions are discussed.

Laboratory spectroscopic analyses of electron irradiated alkanes and alkenes in solar system ices

NASA Astrophysics Data System (ADS)

Hand, K. P.; Carlson, R. W.

2012-03-01

We report results from laboratory experiments of 10 keV electron irradiation of thin ice films of water and short-chain hydrocarbons at ˜10-8 Torr and temperatures ranging from 70-100 K. Hydrocarbon mixtures include water with C3H8, C3H6, C4H10 (butane and isobutane), and C4H8, (1-butene and cis/trans-2-butene). The double bonds of the alkenes in our initial mixtures were rapidly destroyed or converted to single carbon bonds, covalent bonds with hydrogen, bonds with -OH (hydroxyl), bonds with oxygen (C-O), or double bonds with oxygen (carbonyl). Spectra resulting from irradiation of alkane and alkene ices are largely indistinguishable; the initial differences in film composition are destroyed and the resulting mixture includes long-chain, branched aliphatics, aldehydes, ketones, esters, and alcohols. Methane was observed as a product during radiolysis but CO was largely absent. We find that while some of the carbon is oxidized and lost to CO2 formation, some carbon is sequestered into highly refractory, long-chain aliphatic compounds that remain as a thin residue even after the ice film has been raised to standard temperature and pressure. We conclude that the high availability of hydrogen in our experiments leads to the formation of the formyl radical which then serves as the precursor for formaldehyde and polymerization of longer hydrocarbon chains.

Study on Solution Properties of Binary Mixtures of Some Industrially Important Solvents with Cyclohexylamine and Cyclohexanone at 298.15 K

NASA Astrophysics Data System (ADS)

Roy, Mahendra Nath; Das, Rajesh Kumar; Chanda, Riju

2010-03-01

Densities and viscosities were measured for the binary mixtures of cyclohexylamine and cyclohexanone with butyl acetate, butanone, butylamine, tert-butylamine, and 2-butoxyethanol at 298.15 K over the entire composition range. From density data, the values of the excess molar volume ( V E) have been calculated. The experimental viscosity data were correlated by means of the equation of Grunberg-Nissan. The density and viscosity data have been analyzed in terms of some semiempirical viscosity models. The results are discussed in terms of molecular interactions and structural effects. The excess molar volume is found to be either negative or positive depending on the molecular interactions and the nature of the liquid mixtures and is discussed in terms of molecular interactions and structural changes.

Experimental measurements of vapor-liquid equilibria of the H2O + CO2 + CH4 ternary system

USGS Publications Warehouse

Qin, J.; Rosenbauer, R.J.; Duan, Zhenhao

2008-01-01

Reported are the experimental measurements on vapor-liquid equilibria in the H2O + CO2 + CH4 ternary system at temperatures from (324 to 375) K and pressures from (10 to 50) MPa. The results indicate that the CH4 solubility in the ternary mixture is about 10 % to 40 % more than that calculated by interpolation from the Henry's law constants of the binary system, H2O + CH4, and the solubility of CO2 is 6 % to 20 % more than what is calculated by the interpolation from the Henry's law constants of the binary mixture, H 2O + CO2. ?? 2008 American Chemical Society.

Synthesis of Organic Compounds for Malaria Chemotherapeutic Studies

DTIC Science & Technology

1975-10-01

the following Schemue. (.11 Hr C11 3() N03 3 K%.0 A-4 A-5 A-6 C 1 11--(112)3 -(2H2 el NL i 3 A4A A-BI4 %JIA%~N ,t I,,-’. rominationA’ of veratrole (A-4...80)o A mixture of 69 g (0,5 mole) of veratrole , 80 ml Of CC1 4 , and 84 g (0.5 mole) of N-bromosuccinimide was refluxed for 6 hr. It was cooled and...34 4,5-Dinittoveratrole (A-82) k ~To a stirred mixture of 138 g (1.0 mole) of veratrole in 200 milq of AcOll at 150 was added 68 mil (96 g) of

Surface Enrichment in Equimolar Mixtures of Non-Functionalized and Functionalized Imidazolium-Based Ionic Liquids.

PubMed

Heller, Bettina S J; Kolbeck, Claudia; Niedermaier, Inga; Dommer, Sabine; Schatz, Jürgen; Hunt, Patricia; Maier, Florian; Steinrück, Hans-Peter

2018-04-12

For equimolar mixtures of ionic liquids with imidazolium-based cations of very different electronic structure, we observe very pronounced surface enrichment effects by angle-resolved X-ray photoelectron spectroscopy (XPS). For a mixture with the same anion, that is, 1-methyl-3-octylimidazolium hexafluorophosphate+1,3-di(methoxy)imidazolium hexafluorophosphate ([C 8 C 1 Im][PF 6 ]+[(MeO) 2 Im][PF 6 ]), we find a strong enrichment of the octyl chain-containing [C 8 C 1 Im] + cation and a corresponding depletion of the [(MeO) 2 Im] + cation in the topmost layer. For a mixture with different cations and anions, that is, [C 8 C 1 Im][Tf 2 N]+[(MeO) 2 Im][PF 6 ], we find both surface enrichment of the [C 8 C 1 Im] + cation and the [Tf 2 N] - (bis[(trifluoromethyl)sulfonyl]imide) anion, while [(MeO) 2 Im] + and [PF 6 ] - are depleted from the surface. We propose that the observed behavior in these mixtures is due to a lowering of the surface tension by the enriched components. Interestingly, we observe pronounced differences in the chemical shifts of the imidazolium ring signals of the [(MeO) 2 Im] + cations as compared to the non-functionalized cations. Calculations of the electronic structure and the intramolecular partial charge distribution of the cations contribute to interpreting these shifts for the two different cations. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Deviation between the chemistry of Ce(IV) and Pu(IV) and routes to ordered and disordered heterobimetallic 4f/5f and 5f/5f phosphonates.

PubMed

Diwu, Juan; Wang, Shuao; Good, Justin J; DiStefano, Victoria H; Albrecht-Schmitt, Thomas E

2011-06-06

The heterobimetallic actinide compound UO(2)Ce(H(2)O)[C(6)H(4)(PO(3)H)(2)](2)·H(2)O was prepared via the hydrothermal reaction of U(VI) and Ce(IV) in the presence of 1,2-phenylenediphosphonic acid. We demonstrate that this is a kinetic product that is not stable with respect to decomposition to the monometallic compounds. Similar reactions have been explored with U(VI) and Ce(III), resulting in the oxidation of Ce(III) to Ce(IV) and the formation of the Ce(IV) phosphonate, Ce[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O, UO(2)Ce(H(2)O)[C(6)H(4)(PO(3)H)(2)](2)·H(2)O, and UO(2)[C(6)H(4)(PO(3)H)(2)](H(2)O)·H(2)O. In comparison, the reaction of U(VI) with Np(VI) only yields Np[C(6)H(4)(PO(3)H)(2)](2)·2H(2)O and aqueous U(VI), whereas the reaction of U(VI) with Pu(VI) yields the disordered U(VI)/Pu(VI) compound, (U(0.9)Pu(0.1))O(2)[C(6)H(4)(PO(3)H)(2)](H(2)O)·H(2)O, and the Pu(IV) phosphonate, Pu[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O. The reactions of Ce(IV) with Np(VI) yield disordered heterobimetallic phosphonates with both M[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O (M = Ce, Np) and M[C(6)H(4)(PO(3)H)(2)](2)·2H(2)O (M = Ce, Np) structures, as well as the Ce(IV) phosphonate Ce[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O. Ce(IV) reacts with Pu(IV) to yield the Pu(VI) compound, PuO(2)[C(6)H(4)(PO(3)H)(2)](H(2)O)·3H(2)O, and a disordered heterobimetallic Pu(IV)/Ce(IV) compound with the M[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O (M = Ce, Pu) structure. Mixtures of Np(VI) and Pu(VI) yield disordered heterobimetallic Np(IV)/Pu(IV) phosphonates with both the An[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O (M = Np, Pu) and An[C(6)H(4)(PO(3)H)(2)](2)·2H(2)O (M = Np, Pu) formulas. © 2011 American Chemical Society

Influence of ball milling and annealing conditions on the properties of L10 FePt nanoparticles fabricated by a new green chemical synthesis method

NASA Astrophysics Data System (ADS)

Hu, X. C.; Capobianchi, A.; Gallagher, R.; Hadjipanayis, G. C.

2014-05-01

In this work, a new green chemical strategy for the synthesis of L10 FePt alloy nanoparticles is reported. The precursor is a polycrystalline molecular complex (Fe(H2O)6PtCl6), in which Fe and Pt atoms are arranged on alternating planes and milled with NaCl to form nanocrystals. Then the mixture was annealed under reducing atmosphere (5% H2 and 95% Ar) at temperatures varying from 350 °C to 500 °C for 2 h with a heating rate of 5 °C/min. After the reduction, the mixture was washed with water to remove the NaCl and L10 FePt nanoparticles were obtained. The X-Ray Diffraction pattern showed the presence of the characteristic peaks of the fct phase of FePt nanoparticles. Influence of precursor/NaCl ratio and ball milling time on particle size was investigated. Transmission electron microscopy images revealed that smaller precursor/NaCl ratio (10 mg/20 g) and longer milling time (15 h) lead to smaller particle size and narrower size distribution. Milling time does not influence the coercivity much but the decrease of the amount of precursor leads to a decrease of coercivity from 10.8 kOe to 4.8 kOe.

Phase Behavior of Binary Mixture of Heptaethylene Glycol Decyl Ether and Water: Formation of Phase Compound in Solid Phase

PubMed

Nibu; Suemori; Inoue

1997-07-01

Differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR) were used to construct and characterize the phase diagram for a binary mixture of heptaethylene glycol decyl ether (C10 E7 ) and water in the temperature range from -60 to 80°C. Plots of the endothermic peak temperatures obtained by DSC measurements against compositions provided eutectic solid-liquid phase boundaries with a eutectic composition of 34 wt% of H2 O. On the other hand, heat of fusion per unit weight of the mixture changed discretely at the composition corresponding to the "eutectic" composition. Furthermore, the IR spectra obtained for the mixture in the solid phase were well reproduced as a superposition of those for the mixture of 34 wt% H2 O and pure components but were not reproduced by superimposing the spectra obtained for the solid surfactant and ice. These observations indicate that a solid phase compound is formed between C10 E7 and water with a stoichiometry of 1:14 and that the compound and pure components exist as separate phases, rather than the phases separating into surfactant and ice, which would be expected if the C10 E7 /water mixture formed a true eutectic mixture system. It is estimated from the composition corresponding to the phase compounds that two molecules of water per oxyethylene unit are bound to hydrophilic polyoxyethylene chain of C10 E7 to form a hydrated compound.

Synthesis of complex organic molecules in simulated methane rich astrophysical ices

NASA Astrophysics Data System (ADS)

Esmaili, Sasan; Bass, Andrew D.; Cloutier, Pierre; Sanche, Léon; Huels, Michael A.

2017-12-01

It has been proposed that organic molecules required for life on earth may be formed by the radiation processing of molecular ices in space environments, e.g., within our solar system. Such processes can be studied in the laboratory with surface science analytical techniques and by using low-energy electron (LEE) irradiation to simulate the effects of the secondary electrons that are generated in great abundance whenever ionizing radiation interacts with matter. Here we present new measurements of 70 eV LEE irradiation of multilayer films of CH4, 18O2, and CH4/18O2 mixtures (3:1 ratio) at 22 K. The electron stimulated desorption (ESD) yields of cations and anions have been recorded as a function of electron fluence. At low fluence, the prompt desorption of more massive multi-carbon or C—O containing cationic fragments agrees with our earlier measurements. However, new anion ESD signals of C2-, C2H-, and C2H2- from CH4/18O2 mixtures increase with fluence, indicating the gradual synthesis (and subsequent electron-induced fragmentation) of new, more complex species containing several C and possibly O atoms. Comparisons between the temperature programed desorption (TPD) mass spectra of irradiated and unirradiated films show the electron-induced formation of new chemical species, the identities of which are confirmed by reference to the NIST database of electron impact mass spectra and by TPD measurements of films composed of the proposed products. New species observed in the TPD of irradiated mixture films include C3H6, C2H5OH, and C2H6. Furthermore, X-ray photoelectron spectroscopy of irradiated films confirms the formation of C—O, C=O, and O=C—O— bonds of newly formed molecules. Our experiments support the view that secondary LEEs produced by ionizing radiation drive the chemistry in irradiated ices in space, irrespective of the radiation type.

Combined effects of mustard flour, acetic acid, and salt against Esherichia coil O157:H7 stored at 5 and 22 degrees C.

PubMed

Rhee, Min-Suk; Dougherty, Richard H; Kang, Dong-Hyun

2002-10-01

The combined effects of acetic acid and mustard flour were investigated to ascertain their impact on Escherichia coli O157:H7 stored at 5 and 22 degrees C. Samples were prepared with various concentrations of acetic acid (0, 0.25, 0.5, 0.75, and 1% [vol/vol]) combined with 10% (wt/vol) Baltimore or Coleman mustard flour and 2% (fixed; wt/vol) sodium chloride. An acid-adapted mixture of three E. coli O157:H7 strains (10(6) to 10(7) CFU/ml) was inoculated into prepared mustard samples that were stored at 5 and 22 degrees C, and samples were assayed periodically for the survival of E. coli O157:H7. The numbers of E. coli O157:H7 were reduced much more rapidly at 22 degrees C than at 5 degrees C. E. coli O157:H7 was rapidly reduced to below the detection limit (<0.3 log10, CFU/ml) after 1 day at 22 degrees C, whereas it survived for up to 5 days at 5 degrees C. There was no synergistic or additive effect with regard to the killing of E. coli O157:H7 with the addition of small amounts of acetic acid to the mustard flour. When stored at 5 degrees C, mustard in combination with 0.25 (M-0.25), 0.5 (M-0.5), and 0.75% (M-0.75) acetic acid exerted less antimicrobial activity than the control (M-0). The order of lethality at 5 degrees C was generally M-0.25 = M-0.5 < M-0.75 = M-0 < M-1. The addition of small amounts of acetic acid (<0.75%) to mustard retards the reduction of E coli O157:H7. Statistical reduction in populations of E. coli O157:H7 (P < 0.05) was enhanced relative to that of the control (mustard alone) only with the addition of 1% acetic acid. This information may help mustard manufacturers to understand the antimicrobial activity associated with use of mustard flour in combination with acetic acid.

Reduction of Escherichia coli O157:H7 viability on leafy green vegetables by treatment with a bacteriophage mixture and trans-cinnamaldehyde.

PubMed

Viazis, Stelios; Akhtar, Mastura; Feirtag, Joellen; Diez-Gonzalez, Francisco

2011-02-01

Enterohemorrhagic Escherichia coli (EHEC) O157:H7 has been recognized as a major foodborne pathogen responsible for frequent gastroenteritis outbreaks. Phages and essential oils can be used as a natural antimicrobial method to reduce bacterial pathogens from the food supply. The objective of this study was to determine the effect of a bacteriophage cocktail, BEC8, alone and in combination with the essential oil trans-cinnameldehyde (TC) on the viability of a mixture of EHEC O157:H7 strains applied on whole baby romaine lettuce and baby spinach leaves. The EHEC O157:H7 strains used were Nal(R) mutants of EK27, ATCC 43895, and 472. Exponentially growing cells from tryptic soy (TS) broth cultures were spot inoculated on leaves and dried. EHEC cells were placed at low, medium, and high inoculum levels (10(4), 10(5), and 10(6) CFU/mL, respectively). Appropriate controls, BEC8 (approx. 10(6) PFU/leaf), and TC (0.5% v/v) were applied on treated leaves. The leaves were incubated at 4, 8, 23, and 37 °C in Petri dishes with moistened filter papers. EHEC survival was determined using standard plate count on nalidixic acid (50 μg/mL) Sorbitol MacConkey agar. No survivors were detected when both leaves were treated with BEC8 or TC individually at low inoculum levels after 24 h at 23 and 37 °C. When the EHEC inoculum size increased and/or incubation temperature decreased, the efficacy of BEC8 and TC decreased. However, when the two treatments were combined, no survivors were detected after 10 min at all temperatures and inoculum levels on both leafy greens. These results indicated that the BEC8/TC combination was highly effective against EHEC on both leafy greens. This combination could potentially be used as an antimicrobial to inactivate EHEC O157:H7 and reduce their incidence in the food chain. Copyright © 2010 Elsevier Ltd. All rights reserved.

Effect of simulated coal-derived gas composition on H{sub 2}S poisoning behavior evaluated using a disaggregation scheme

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, T.S.; Miao, H.; Chen, T.

2009-07-01

H{sub 2}S poisoning is an important issue for solid oxide fuel cells (SOFCs) operated with syngas. The effect of simulated coal-derived gas composition on H{sub 2}S poisoning behavior was evaluated using a disaggregation scheme where the influence of H{sub 2} content was determined separately using a typical anode-supported SOFC operated with a N2/H{sub 2} mixture gas, while the effect of other compositions (CO, CO{sub 2}, and H{sub 2}O) was investigated with simulated coal-derived gas having constant H{sub 2} and CO flow rates balanced by a H{sub 2}/N2 mixture gas (83% H{sub 2} and 17% N2). The results indicated that themore » extent of H{sub 2}S poisoning was not pertinent to H{sub 2} content when the cell was tested galvanostatically with a current density of 0.3 A/cm{sup 2} at 800{sup o}C using a N2/H{sub 2} mixture gas containing 10 ppm H{sub 2}S, and the H{sub 2}S poisoning impact can be completely removed by switching to sulfur-free gas. The CO, CO{sub 2}, and high water vapor content aggravated the H{sub 2}S poisoning effect, and the performance was almost irrecoverable when the cell was tested with a 35% H{sub 2}-46% CO-16% N2-3% H{sub 2}O mixture gas containing 12.5 ppm H{sub 2}S. However, the introduction of 10% CO{sub 2} and an increase in H{sub 2}O content from 3 to 10% in the mixture gas can promote the performance recoverability to a larger extent.« less

Reactive sulfur species: kinetics and mechanism of the oxidation of cystine by hypochlorous acid to give N,N'-dichlorocystine.

PubMed

Nagy, Péter; Ashby, Michael T

2005-06-01

Cystine and HOCl (a neutrophil-derived oxidant) react to form an intermediate that has a half-life of ca. 5 min at pH 7.5. The intermediate subsequently decomposes to eventually yield a mixture of cystine, higher oxides of Cys, and other uncharacterized species. Spectral titrations, transitory (1)H NMR and UV-vis spectra, and the reaction properties of the intermediate are consistent with a formulation of N,N'-dichlorocystine {NDC = [-SCH(2)CH(NHCl)(CO(2)H)](2)}. The reaction of equimolar amounts of HOCl with cystine at pH 11.3 does not yield N-chlorocystine [NCC = (-O2C)(H3N+)CHCH(2)SSCH(2)CH(NHCl)(CO(2)H)] but rather a 1:1 mixture of NDC and cystine. This result could be explained by two mechanisms: rapid disproportionation of NCC to produce NDC and cystine or a faster reaction of the second equivalent of HOCl with NCC than the first equivalent of HOCl reacts with cystine. The latter mechanism is favored because of our observation by NMR spectroscopy that NDC decomposes via a species that we have assigned as NCC. Thus, disproportionation of NCC is apparently a relatively slow process. The rates of reaction of cystine(0) = [-SCH(2)CH(NH(3)(+))(CO(2)(-))](2) degrees , cystine(1-) = [((-)O(2)C)(H(2)N)CHCH(2)SSCH(2)CH(NH(3)(+))(CO(2)(-))](-), and cystine(2-) = [-SCH(2)CH(NH2)(CO2)(-))]2(2-) have been investigated, and it is clear that cystine(0) is unreactive, whereas cystine(2-) is about four times more reactive than cystine(1-). Accordingly, the following mechanism is proposed (constants for 5 degrees C): HOCl = H+ + OCl-, pK1 = 7.47; cystine(0) = cystine(1-) + H+, pK2 = 8.15; cystine(1-) = cystine(2-) + H+, pK3 = 9.00; cystine(1-) + HOCl --> NCC(1-) + H2O, k4 = 4.3(2) x 10(6) M(-1) s(-1); cystine(2-) + HOCl --> NCC(2)(-) + H2O, k5 = 1.6(2) x 10(7) M(-1) s(-1); NCC(1-) --> NCC(2-) + H+, k6 = fast; NCC(2-) + HOCl --> NDC(2-) + H2O, k7 = fast. At physiologic pH, the k4 pathway dominates. The generation of long-lived chloramine derivatives of cystine may have physiological consequences, since such compounds are known to react with nucleophiles via mechanisms that are also characteristic of HOCl, electrophilic transfer C+.

Exploring the plasma chemistry in microwave chemical vapor deposition of diamond from C/H/O gas mixtures.

PubMed

Kelly, Mark W; Richley, James C; Western, Colin M; Ashfold, Michael N R; Mankelevich, Yuri A

2012-09-27

Microwave (MW)-activated CH(4)/CO(2)/H(2) gas mixtures operating under conditions relevant to diamond chemical vapor deposition (i.e., X(C/Σ) = X(elem)(C)/(X(elem)(C) + X(elem)(O)) ≈ 0.5, H(2) mole fraction = 0.3, pressure, p = 150 Torr, and input power, P = 1 kW) have been explored in detail by a combination of spatially resolved absorption measurements (of CH, C(2)(a), and OH radicals and H(n = 2) atoms) within the hot plasma region and companion 2-dimensional modeling of the plasma. CO and H(2) are identified as the dominant species in the plasma core. The lower thermal conductivity of such a mixture (cf. the H(2)-rich plasmas used in most diamond chemical vapor deposition) accounts for the finding that CH(4)/CO(2)/H(2) plasmas can yield similar maximal gas temperatures and diamond growth rates at lower input powers than traditional CH(4)/H(2) plasmas. The plasma chemistry and composition is seen to switch upon changing from oxygen-rich (X(C/Σ) < 0.5) to carbon-rich (X(C/Σ) > 0.5) source gas mixtures and, by comparing CH(4)/CO(2)/H(2) (X(C/Σ) = 0.5) and CO/H(2) plasmas, to be sensitive to the choice of source gas (by virtue of the different prevailing gas activation mechanisms), in contrast to C/H process gas mixtures. CH(3) radicals are identified as the most abundant C(1)H(x) [x = 0-3] species near the growing diamond surface within the process window for successful diamond growth (X(C/Σ) ≈ 0.5-0.54) identified by Bachmann et al. (Diamond Relat. Mater.1991, 1, 1). This, and the findings of similar maximal gas temperatures (T(gas) ~2800-3000 K) and H atom mole fractions (X(H)~5-10%) to those found in MW-activated C/H plasmas, points to the prevalence of similar CH(3) radical based diamond growth mechanisms in both C/H and C/H/O plasmas.

Oxidant effect of La(NO3)3·6H2O solution on the crystalline characteristics of nanocrystalline ZrO2 films grown by atomic layer deposition

NASA Astrophysics Data System (ADS)

Oh, Nam Khen; Kim, Jin-Tae; Kang, Goru; An, Jong-Ki; Nam, Minwoo; Kim, So Yeon; Park, In-Sung; Yun, Ju-Young

2017-02-01

Nanocrystalline ZrO2 films were synthesized by atomic layer deposition method using CpZr[N(CH3)2]3 (Cp = C5H5) as the metal precursor and La(NO3)3·6H2O solution as the oxygen source. La element in the deposited ZrO2 films could not be detected as its content was below the resolution limit of the X-ray photoelectron spectroscopy. The alternative introduction of La(NO3)3·6H2O solution to conventionally used H2O as the oxidant effectively altered the crystalline structure, grain size, and surface roughness of the grown ZrO2 films. Specifically, the crystalline structure of the ZrO2 film changed from a mixture of tetragonal and monoclinic phases to monoclinic phase. The average grain size also increased, and the resulting film surface became rougher. The average grain sizes of the ZrO2 films prepared from La(NO3)3·6H2O solution at concentrations of 10, 20, 30, and 40% were 280, 256, 208, and 200 nm, respectively, whereas that prepared using H2O oxidant was 142 nm. However, the concentration of La(NO3)3·6H2O solution minimally influenced the crystalline characteristics of the nanocrystalline ZrO2 films i.e., the crystalline structure, grain size, and surface roughness except for crystallite size.

Validation of time and temperature values as critical limits for the control of Escherichia coli O157:H7 during the production of fresh ground beef.

PubMed

Mann, J E; Brashears, M M

2006-08-01

In order to provide beef processors with valuable data to validate critical limits set for temperature during grinding, a study was conducted to determine Escherichia coli o157:H7 growth at various temperatures in raw ground beef. Fresh ground beef samples were inoculated with a cocktail mixture of streptomycin-resistant E. coli O157:H7 to facilitate recovery in the presence of background flora. Samples were held at 4.4, 7.2, and 10 degrees C, and at room temperature (22.2 to 23.3 degrees C) to mimic typical processing and holding temperatures observed in meat processing environments. E. coli O157:H7 counts were determined by direct plating onto tryptic soy agar with streptomycin (1,000 microg/ml), at 2-h intervals over 12 h for samples held at room temperature. Samples held under refrigeration temperatures were sampled at 4, 8, 12, 24, 48, and 72 h. Less than one log of E. coli O157:H7 growth was observed at 48 h for samples held at 10 degrees C. Samples held at 4.4 and 7.2 degrees C showed less than one log of E. coli O157:H7 growth at 72 h. Samples held at room temperature showed no significant increase in E. coli O157:H7 counts for the first 6 h, but increased significantly afterwards. These results illustrate that meat processors can utilize a variety of time and temperature combinations as critical limits in their hazard analysis critical control point plans to minimize E. coli O157:H7 growth during the production and storage of ground beef.

AtomicNuclearProperties

Science.gov Websites

) Polytrifluorochloroethylene [C2F3Cl]n Polyvinylacetate [CH2CHOCOCH3]n Polyvinyl alcohol (C2H3-O-H)n Polyvinyl butyral [C8H1302 other materal for properties of interest in high-energy physics: stopping power (<-dE/dx>) tables (C10H16O) Aniline (C6H5NH2) Anthracene (C14H10) Benzene C6H6 Butane (C4H10) n-Butyl alcohol (C4H9OH) Carbon

Metal reduction at point-of-use filtration

NASA Astrophysics Data System (ADS)

Umeda, Toru; Daikoku, Shusaku; Varanasi, Rao; Tsuzuki, Shuichi

2016-03-01

We explored the metal removal efficiency of Nylon 6,6 and HDPE (High Density Polyethylene) membrane based filters, in solvents of varying degree of polarity such as Cyclohexanone and 70:30 mixture of PGME (Propylene Glycol Monomethyl Ether) and PGMEA (Propylene Glycol Monomethyl Ether), In all the solvents tested, Nylon 6,6 membrane filtration was found to be significantly more effective in removing metals than HDPE membranes, regardless of their respective membrane pore sizes. Hydrophilic interaction chromatography (HILIC) mechanism was invoked to rationalize metal removal efficiency dependence on solvent hydrophobicity.

Molecular dynamics investigation of separation of hydrogen sulfide from acidic gas mixtures inside metal-doped graphite micropores.

PubMed

Huang, Pei-Hsing

2015-09-21

The separation of poisonous compounds from various process fluids has long been highly intractable, motivating the present study on the dynamic separation of H2S in acidic-gas-mixture-filled micropores. The molecular dynamics approach, coupled with the isothermal-isochoric ensemble, was used to model the molecular interactions and adsorption of H2S/CO2/CO/H2O mixtures inside metal-doped graphite slits. Due to the difference in the adsorption characteristics between the two distinct adsorbent materials, the metal dopant in the graphitic micropores leads to competitive adsorption, i.e. the Au and graphite walls compete to capture free adsorbates. The effects of competitive adsorption, coupled with changes in the gas temperature, concentration, constituent ratio and slit width on the constituent separation of mixtures were systematically studied. The molecule-wall binding energies calculated in this work (those of H2S, H2O and CO on Au walls and those of H2O, CO and CO2 on graphite walls) show good agreement with those obtained using density functional theory (DFT) and experimental results. The z-directional self-diffusivities (Dz) for adsorbates inside the slit ranged from 10(-9) to 10(-7) m(2) s(-1) as the temperature was increased from 10 to 500 K. The values are comparable with those for a typical microporous fluid (10(-8)-10(-9) m(2) s(-1) in a condensed phase and 10(-6)-10(-7) m(2) s(-1) in the gaseous state). The formation of H-bonding networks and hydrates of H2S is disadvantageous for the separation of mixtures. The results indicate that H2S can be efficiently separated from acidic gas mixtures onto the Au(111) surface by (i) reducing the mole fraction of H2S and H2O in the mixtures, (ii) raising the gas temperature to the high temperature limit (≥400 K), and (iii) lowering the slit width to below the threshold dimension (≤23.26 Å).

Production and optical constraints of ice tholin from charged particle irradiation of (1:6) C2H6/H2O at 77 K

NASA Astrophysics Data System (ADS)

Khare, B. N.; Thompson, W. R.; Cheng, L.; Chyba, C.; Sagan, C.; Arakawa, E. T.; Meisse, C.; Tuminello, P. S.

1993-06-01

Fifty separate irradiations of a 6:1 mixture of H2O/C2H6 ice conducted over a 5-month period have yielded sufficient tholin for the determination of its physical constants in the 0.06 to 40 micron range. While the imaginary part of the refractive index k was obtained by transmission measurements on thin-film samples and Kramers-Kronig analysis (KKA), the real part of the refractive index was obtained by KKA and ellipsometry; these data may prove useful in cometary and outer solar system spectrometric interpretation.

Liquid-phase oxidation of cyclohexanone over cerium oxide catalyst

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, H.C.; Weng, H.S.

Catalytic oxidation of cyclohexanone in the liquid phase with glacial acetic acid as the solvent over cerium oxide was studied between 5 and 15 atm and 98 and 118 {degrees} C in a batch reactor. The products were adipic acid, glutaric acid, succinic acid, caprolactone, carbon oxides, etc. The reaction undergoes a short induction period prior to a rapid reaction regime. In both regimes, the reaction is independent of oxygen pressure when the system pressure is above 10 atm. The induction period is inversely proportional to both of the catalyst weight and cyclohexanone concentration.During the rapid reaction regime, the reactionmore » rate was found to be proportional to the 0.5 power of the catalyst weight and to the 1.5 power of the cyclohexanone concentration. Reaction mechanisms and rate expressions are proposed. The carbon oxides produced in this study were much lower than those previously reported. The cerium oxide catalyst is stable during the reaction.« less

Three cocrystals and a cocrystal salt of pyrimidin-2-amine and glutaric acid.

PubMed

Odiase, Isaac; Nicholson, Catherine E; Ahmad, Ruksanna; Cooper, Jerry; Yufit, Dmitry S; Cooper, Sharon J

2015-04-01

Four new cocrystals of pyrimidin-2-amine and propane-1,3-dicarboxylic (glutaric) acid were crystallized from three different solvents (acetonitrile, methanol and a 50:50 wt% mixture of methanol and chloroform) and their crystal structures determined. Two of the cocrystals, namely pyrimidin-2-amine-glutaric acid (1/1), C4H5N3·C6H8O4, (I) and (II), are polymorphs. The glutaric acid molecule in (I) has a linear conformation, whereas it is twisted in (II). The pyrimidin-2-amine-glutaric acid (2/1) cocrystal, 2C4H5N3·C6H8O4, (III), contains glutaric acid in its linear form. Cocrystal-salt bis(2-aminopyrimidinium) glutarate-glutaric acid (1/2), 2C4H6N3(+)·C6H6O4(2-)·2C6H8O4, (IV), was crystallized from the same solvent as cocrystal (II), supporting the idea of a cocrystal-salt continuum when both the neutral and ionic forms are present in appreciable concentrations in solution. The diversity of the packing motifs in (I)-(IV) is mainly caused by the conformational flexibility of glutaric acid, while the hydrogen-bond patterns show certain similarities in all four structures.

Controlling the biodegradability of poly(butylene succinate-co-butylene adipate) (PBSA) by solvents used in the dried-gel process

NASA Astrophysics Data System (ADS)

Yamazaki, Hana; Kamitabira, Saya; Maeda, Tomoki; Hotta, Atsushi

Considering an environmentally friendly material, poly(butylene succinate-co-butylene adipate)(PBSA) is one of the attractive biodegradable plastics that can be eventually degraded into H2O and CO2 by neighboring water molecules and microorganisms after the disposal. In order to expand the application of PBSA, the precise control of the biodegradability of PBSA is necessary. In this study, the dried-gel process was introduced to control the biodegradability of PBSA. The dried PBSA gels were prepared by using three different solvents (toluene, cyclohexanone, and o-dichlorobenzene). The scanning electron microscopy (SEM) micrographs revealed that the PBSA prepared by toluene had smaller spherocrystals than the other PBSA dried-gels prepared by cyclohexanone or o-dichlorobenzene. The biodegradability testing by immersing the three types of PBSA in NaOH aq. showed that the percentage of the weight loss of the PBSA produced by toluene was the highest. The results indicated that the microstructures of PBSA could be controlled by changing solvents during the gel preparations, and that the biodegradability of PBSA could therefore be efficiently modified by changing solvents. This work was supported by a Grant-in-Aid for Scientific Research (A) (No. 15H02298 to A.H.) and a Grant-in-Aid for Research Activity Start-up (No.15H06586 to T.M.) from JSPS: KAKENHI\\x9D.

Threefold interweaving of (4,4) nets built from R(10)10(58) rings inthe hydrogen-bonded adduct 1,4-diazabicyclo

PubMed

Burchell; Ferguson; Lough; Glidewell

2000-09-01

The 1:1 adduct of 1,4-diazabicyclo[2.2.2]octane and 5-hydroxyisophthalic acid is a salt, [H(C(6)H(12)N(2))](+). [HOC(6)H(3)(COOH)COO](-) or C(6)H(13)N(2)(+).C(8)H(5)O(5)(-). The ions are linked by three types of hydrogen bond, i.e. N-H.O, O-H.O and O-H.N, into continuous two-dimensional (4,4) nets built from a single type of R(10)(10)(58) ring. Six independent sheets of this type make up the structure and these are interwoven in sets of three.

Solid state structural investigations of the bis(chalcone) compound with single crystal X-ray crystallography, DFT, gamma-ray spectroscopy and chemical spectroscopy methods

NASA Astrophysics Data System (ADS)

Yakalı, Gül; Biçer, Abdullah; Eke, Canel; Cin, Günseli Turgut

2018-04-01

A bis(chalcone), (2E,6E)-2,6-bis((E)-3phenylallidene)cyclohexanone, was characterized by 1H NMR, 13C NMR, FTIR, UV-Vis spectroscopy, gamma-ray spectroscopy and single crystal X- ray structural analysis. The optimized molecular structure of the compound is calculated using DFT/B3LYP with 6-31G (d,p) level. The calculated geometrical parameters are in good agreement with the experimental data obtained from our reported X-ray structure. The powder and single crystal compounds were gama-irradiated using clinical electron linear accelerator and 60Co gamma-ray source, respectively. Spectral studies (1H NMR, 13C NMR, FTIR and UV-Vis) of powder chalcone compound were also investigated before and after irradiation. Depending on the irradiation notable changes were observed in spectral features powder sample. Single crystal X-ray diffraction investigation shows that both unirradiated and irradiated single crystal samples crystallizes in a orthorhombic crystal system in the centrosymmetric space group Pbcn and exhibits an C-H..O intramolecular and intermolecular hydrogen bonds. The crystal packing is stabilised by strong intermolecular bifurcate C-H..O hydrogen bonds and π…π stacking interactions. The asymmetric unit of the title compound contains one-half of a molecule. The other half of the molecule is generated with (1-x,y,-3/2-z) symmetry operator. The molecule is almost planar due to having π conjugated system of chalcones. However, irradiated single crystal compound showed significant changes lattice parameters, crystal volume and density. According to results of gamma-ray spectroscopy, radioactive elements of powder compound which are 123Sb(n,g),124Sb,57Fe(g,p),56Mn, 55Mn(g,n), and 54Mn were determined using photoactivation analysis. However, the most intensive gamma-ray energy signals are 124Sb.

Prediction of the PVTx and VLE properties of natural gases with a general Helmholtz equation of state. Part I: Application to the CH4-C2H6-C3H8-CO2-N2 system

NASA Astrophysics Data System (ADS)

Mao, Shide; Lü, Mengxin; Shi, Zeming

2017-12-01

A general equation of state (EOS) explicit in Helmholtz free energy has been developed to predict the pressure-volume-temperature-composition (PVTx) and vapor-liquid equilibrium (VLE) properties of the CH4-C2H6-C3H8-CO2-N2 fluid mixtures (main components of natural gases). This EOS, which is a function of temperature, density and composition, with four mixing parameters used, is based on the improved EOS of Sun and Ely (2004) for the pure components (CH4, C2H6, C3H8, CO2 and N2) and contains a simple generalized departure function presented by Lemmon and Jacobsen (1999). Comparison with the experimental data available indicates that the EOS can calculate the PVTx and VLE properties of the CH4-C2H6-C3H8-CO2-N2 fluid mixtures within or close to experimental uncertainties up to 623 K and 1000 bar within full range of composition. Isochores of the CH4-C2H6-C3H8-CO2-N2 system can be directly calculated from this EOS to interpret the corresponding microthermometric and Raman analysis data of fluid inclusions. The general EOS can calculate other thermodynamic properties if the ideal Helmholtz free energy of fluids is combined, and can also be extended to the multi-component natural gases including the secondary alkanes (carbon number above three) and none-alkane components such as H2S, SO2, O2, CO, Ar and H2O. This part of work will be finished in the near future.

Formation of amino acids and nucleotide bases in a Titan atmosphere simulation experiment.

PubMed

Hörst, S M; Yelle, R V; Buch, A; Carrasco, N; Cernogora, G; Dutuit, O; Quirico, E; Sciamma-O'Brien, E; Smith, M A; Somogyi, A; Szopa, C; Thissen, R; Vuitton, V

2012-09-01

The discovery of large (>100 u) molecules in Titan's upper atmosphere has heightened astrobiological interest in this unique satellite. In particular, complex organic aerosols produced in atmospheres containing C, N, O, and H, like that of Titan, could be a source of prebiotic molecules. In this work, aerosols produced in a Titan atmosphere simulation experiment with enhanced CO (N(2)/CH(4)/CO gas mixtures of 96.2%/2.0%/1.8% and 93.2%/5.0%/1.8%) were found to contain 18 molecules with molecular formulae that correspond to biological amino acids and nucleotide bases. Very high-resolution mass spectrometry of isotopically labeled samples confirmed that C(4)H(5)N(3)O, C(4)H(4)N(2)O(2), C(5)H(6)N(2)O(2), C(5)H(5)N(5), and C(6)H(9)N(3)O(2) are produced by chemistry in the simulation chamber. Gas chromatography-mass spectrometry (GC-MS) analyses of the non-isotopic samples confirmed the presence of cytosine (C(4)H(5)N(3)O), uracil (C(5)H(4)N(2)O(2)), thymine (C(5)H(6)N(2)O(2)), guanine (C(5)H(5)N(5)O), glycine (C(2)H(5)NO(2)), and alanine (C(3)H(7)NO(2)). Adenine (C(5)H(5)N(5)) was detected by GC-MS in isotopically labeled samples. The remaining prebiotic molecules were detected in unlabeled samples only and may have been affected by contamination in the chamber. These results demonstrate that prebiotic molecules can be formed by the high-energy chemistry similar to that which occurs in planetary upper atmospheres and therefore identifies a new source of prebiotic material, potentially increasing the range of planets where life could begin.

High pressure hydriding of sponge-Zr in steam-hydrogen mixtures

NASA Astrophysics Data System (ADS)

Soo Kim, Yeon; Wang, Wei-E.; Olander, D. R.; Yagnik, S. K.

1997-07-01

Hydriding kinetics of thin sponge-Zr layers metallurgically bonded to a Zircaloy disk has been studied by thermogravimetry in the temperature range 350-400°C in 7 MPa hydrogen-steam mixtures. Some specimens were prefilmed with a thin oxide layer prior to exposure to the reactant gas; all were coated with a thin layer of gold to avoid premature reaction at edges. Two types of hydriding were observed in prefilmed specimens, viz., a slow hydrogen absorption process that precedes an accelerated (massive) hydriding. At 7 MPa total pressure, the critical ratio of H 2/H 2O above which massive hydriding occurs at 400°C is ˜ 200. The critical H 2/H 20 ratio is shifted to ˜2.5 × 103 at 350°C. The slow hydriding process occurs only when conditions for hydriding and oxidation are approximately equally favorable. Based on maximum weight gain, the specimen is completely converted to δ-ZrH 2 by massive hydriding in ˜5 h at a hydriding rate of ˜10 -6 mol H/cm 2 s. Incubation times of 10-20 h prior to the onset of massive hydriding increases with prefilm oxide thickness in the range of 0-10 μm. By changing to a steam-enriched gas, massive hydriding that initially started in a steam-starved condition was arrested by re-formation of a protective oxide scale.

Electrospray ionization mass spectrometry of the photodegradation of naphthenic acids mixtures irradiated with titanium dioxide.

PubMed

Headley, John V; Du, Jing-Long; Peru, Kerry M; McMartin, Dena W

2009-05-01

Electrospray ionization mass spectrometry was used to study the photodegradation of an oil sands naphthenic acid (NA) mixture, a commercial Fluka NA mixture and a candidate NA, 4-Methyl-cyclohexaneaceticic acid (4-MCHAA) irradiated with TiO(2) (P25) suspension under both fluorescent and natural sunlight. Under natural sunlight irradiation over the TiO(2) suspension, approximately 75% of compounds in the NA mixtures and 100% of 4-MCHAA were degraded in 8 h. No degradation was observed under dark conditions, regardless of the presence or absence of TiO(2). The structural formula of the NAs is given by C(n)H(2n + z)O(2), where n represents the carbon number and z specifies a homologous family with 0-6 rings (z = 0 to -12). The degree of degradation was noted to vary among the NA mixtures and the candidate NA compound with more efficient degradation achieved for molecules with -z values from 0 to 6. The difference in the efficacy of the photocatalysis was likely due to the structure and size of the compounds. In the case of -z = 6 to 12, steric constraints are a key factor what hinders photocatalysis.

RPCs in biomedical applications

NASA Astrophysics Data System (ADS)

Belli, G.; De Vecchi, C.; Giroletti, E.; Guida, R.; Musitelli, G.; Nardò, R.; Necchi, M. M.; Pagano, D.; Ratti, S. P.; Sani, G.; Vicini, A.; Vitulo, P.; Viviani, C.

2006-08-01

We are studying possible applications of Resistive Plate Chambers (RPCs) in the biomedical domain such as Positron Emission Tomography (PET). The use of RPCs in PET can provide several improvements on the usual scintillation-based detectors. The most striking features are the extremely good spatial and time resolutions. They can be as low as 50 μm and 25 ps respectively, to be compared to the much higher intrinsic limits in bulk detectors. Much efforts have been made to investigate suitable materials to make RPCs sensitive to 511 keV photons. For this reason, we are studying different types of coating employing high Z materials with proper electrical resistivity. Later investigations explored the possibility of coating glass electrodes by mean of serigraphy techniques, employing oxide based mixtures with a high density of high Z materials; the efficiency is strongly dependent on its thickness and it reaches a maximum for a characteristic value that is a function of the compound (usually a few hundred microns). The most promising mixtures seem to be PbO, Bi 2O 3 and Tl 2O. Preliminary gamma efficiency measurements for a Multigap RPC prototype (MRPC) are presented as well as simulations using GEANT4-based framework. The MRPC has 5 gas gaps; their spacings are kept by 0.3 mm diameter nylon fishing line, electrodes are made of thin glasses (1 mm for the outer electrodes, 0.15-0.4 mm for the inner ones). The detector is enclosed in a metallic gas-tight box, filled with a C 2H 2F 4 92.5%, SF 6 2.5%, C 4H 10 5% mixture. Different gas mixtures are being studied increasing the SF6 percentage and results of efficiency as a function of the new mixtures will be presented.

Cyclic water-trimer encapsulation into D2 (22)-C84 fullerene

NASA Astrophysics Data System (ADS)

Slanina, Zdeněk; Uhlík, Filip; Nagase, Shigeru; Akasaka, Takeshi; Lu, Xing; Adamowicz, Ludwik

2018-03-01

The cyclic water-trimer encapsulations into D2 (22)-C84 fullerene are evaluated. The encapsulation energy is computed at the M06-2X/6-31++G∗∗ level and it is found that the trimer storage in C84 yields the potential-energy gain of 10.4 kcal/mol. The encapsulated trimer can have two different forms, either the conformation known with the free gas-phase water trimer or the arrangement with the three non-hydrogen bonded H atoms on the same side of the O-O-O plane. The latter endohedral isomer is lower in the potential energy by 0.071 kcal/mol and forms about 57% of their equilibrium mixture at room temperature.

Bacterial Ice Nucleation in Monodisperse D2O and H2O-in-Oil Emulsions.

PubMed

Weng, Lindong; Tessier, Shannon N; Smith, Kyle; Edd, Jon F; Stott, Shannon L; Toner, Mehmet

2016-09-13

Ice nucleation is of fundamental significance in many areas, including atmospheric science, food technology, and cryobiology. In this study, we investigated the ice-nucleation characteristics of picoliter-sized drops consisting of different D2O and H2O mixtures with and without the ice-nucleating bacteria Pseudomonas syringae. We also studied the effects of commonly used cryoprotectants such as ethylene glycol, propylene glycol, and trehalose on the nucleation characteristics of D2O and H2O mixtures. The results show that the median freezing temperature of the suspension containing 1 mg/mL of a lyophilized preparation of P. syringae is as high as -4.6 °C for 100% D2O, compared to -8.9 °C for 100% H2O. As the D2O concentration increases every 25% (v/v), the profile of the ice-nucleation kinetics of D2O + H2O mixtures containing 1 mg/mL Snomax shifts by about 1 °C, suggesting an ideal mixing behavior of D2O and H2O. Furthermore, all of the cryoprotectants investigated in this study are found to depress the freezing phenomenon. Both the homogeneous and heterogeneous freezing temperatures of these aqueous solutions depend on the water activity and are independent of the nature of the solute. These findings enrich our fundamental knowledge of D2O-related ice nucleation and suggest that the combination of D2O and ice-nucleating agents could be a potential self-ice-nucleating formulation. The implications of self-nucleation include a higher, precisely controlled ice seeding temperature for slow freezing that would significantly improve the viability of many ice-assisted cryopreservation protocols.

Modeling the survival of Escherichia coli O157:H7, Listeria monocytogenes, and Salmonella Typhimurium during fermentation, drying, and storage of soudjouk-style fermented sausage.

PubMed

Hwang, Cheng-An; Porto-Fett, Anna C S; Juneja, Vijay K; Ingham, Steven C; Ingham, Barbara H; Luchansky, John B

2009-02-28

This study quantified and modeled the survival of Escherichia coli O157:H7, Listeria monocytogenes and Salmonella Typhimurium in soudjouk-style fermented sausage during fermentation, drying, and storage. Batter prepared from ground beef (20% fat), seasonings, starter culture, and dextrose was separately inoculated with a multi-strain mixture of each pathogen to an initial inoculum of ca. 6.5 log(10) CFU/g in the batter. The sausages were subsequently fermented at 24 degrees C with a relative humidity (RH) of 90% to 95% for 3 to 5 days to ca. pH 5.2, pH 4.9 or pH 4.6, then dried at 22 degrees C to a(w) 0.92, a(w) 0.89, or a(w) 0.86, respectively, and then stored at 4, 21, or 30 degrees C for up to 60 days. Lethality of the three pathogens was modeled as a function of pH, a(w) and/or storage temperature. During fermentation to pH 5.2 to pH 4.6, cell reductions ranged from 0 to 0.9 log(10) CFU/g for E. coli O157:H7, 0.1 to 0.5 log(10) CFU/g for L. monocytogenes, and 0 to 2.2 log(10) CFU/g for S. Typhimurium. Subsequent drying of sausages of pH 5.2 to pH 4.6 at 22 degrees C with 80% to 85% RH for 3 to 7 days to a(w) of 0.92 to a(w) 0.86 resulted in additional reductions that ranged from 0 to 3.5 log(10) CFU/g for E. coli O157:H7, 0 to 0.4 log(10) CFU/g for L. monocytogenes, and 0.3 to 2.4 log(10) CFU/g for S. Typhimurium. During storage at 4, 21, or 30 degrees C the reduction rates of the three pathogens were generally higher (p<0.05) in sausages with lower pH and lower a(w) that were stored at higher temperatures. Polynomial equations were developed to describe the inactivation of the three pathogens during fermentation, drying, and storage. The applicability of the resulting models for fermented sausage was evaluated by comparing model predictions with published data. Pathogen reductions estimated by the models for E. coli O157:H7 and S. Typhimurium were comparable to 67% and 73% of published data, respectively. Due to limited published data for L. monocytogenes, the models for L. monocytogenes would need additional validations. Results of pathogen reductions from this study may be used as a reference to assist manufacturers of soudjouk-style sausages to adopt manufacturing processes that meet the regulatory requirements. The resulting models may also be used for estimating the survival of E. coli O157:H7 and S. Typhimurium in other similar fermented sausage during fermentation and storage.

The effect of hydrodynamic and thermodynamic factors and the addition of citric acid on the precipitation of calcium oxalate dihydrate.

PubMed

Šter, Anamarija; Šafranko, Silvija; Bilić, Katarina; Marković, Berislav; Kralj, Damir

2018-06-01

This paper reports on the investigation of experimental conditions relevant for spontaneous precipitation of significant amount of pure calcium oxalate dihydrate (COD). For this purpose, the hydrodynamic and thermodynamic parameters, such as mode of agitation, temperature, supersaturation and concentration of additives (citrate ions), have been studied. The results show that in the model systems, without the citrate addition and applied mechanical stirring, calcium oxalate monohydrate (COM) was observed as dominant modification after 20 min of aging, while the magnetic stirring resulted in a formation of a mixture of COM and calcium oxalate trihydrate (COT), regardless of the temperature applied. In the mechanically stirred systems, the addition of citrate ions in the range of concentrations, 0.001 mol dm -3  < c i (Na 3 C 6 H 5 O 7 ) < 0.012 mol dm -3 , caused the formation of COM and COD mixture at all temperatures. At the same conditions and in the magnetically stirred systems formation of COD, in a mixture with COT or COM, has been observed. The highest COD content in the mechanically stirred system was obtained at 45 °C and c i (Na 3 C 6 H 5 O 7 ) = 0.001 mol dm -3 (w = 89.5%), while in the magnetically stirred system almost pure COD was obtained at 37 °C and c i (Na 3 C 6 H 5 O 7 ) = 0.008 mol dm -3 (w = 96.5%).

Synthesis of nano anatase for titanosilicate ETS-10 synthesis

NASA Astrophysics Data System (ADS)

Shafeque, Shihara

Functionalized textiles present a vast and growing niche in the global textile market at US $400 billion [1, 2]. Engelhard Titanium Silicate 10 (ETS-10), a photocatalytic zeo-type material if coated on textiles, is expected to impart useful properties similar to TiO2, such as stain-resistant, odor repellant, bactericidal and enhanced UV protection [3, 4]. Typically, small ETS-10 crystals of size ˜300-800 nm are synthesized using solid titania (e.g., anatase or P25) sources [5, 6, 7]. However, smaller ETS-10 crystals are required for a uniform surface coating with highly effective surface area. The dissolution of titania particles (i.e., their size) is hypothesized to be important in small ETS-10 crystal formation [5, 6, 7]. Nano anatase was synthesized by modification of two methods: direct precipitation [7] and sol-gel synthesis [3]. Analysis by XRD confirmed that both methods produced nano anatase of crystallite size ˜4-5 nm. However, FE-SEM analysis showed that product from direct precipitation, existed as intergrown spheroidal particles with size ˜1.0 mum. These particles dispersed poorly in deionized water. Therefore, the best nano anatase samples were from sol-gel synthesis in two forms, dry powder and colloidal anatase. ETS-10 synthesis was investigated using two methods adopted from literature [6, 7]. The method of Yoon and co-workers [7], with nano anatase in a molar composition of 5.5TEOS: TiO2: 8.4NaOH: 1.43KF: 350H2O: 2.2H2SO4 produced unknown phase(s) with some ETS-10 and quartz. Using colloidal anatase with molar composition 5.5TEOS:1.0TiO 2:8.4NaOH:1.43KF:400H2O:2.2H2SO4 also produced unknown phase(s). The method of Anderson and co-workers [6] with nano anatase powder in a molar composition of 5.5SiO2: TiO 2: 5.2Na2O: 0.5K2O: 113H2O produced quartz with ETS-10 impurity. When colloidal anatase was used, with molar composition TiO2:5.5SiO2:5.2Na2O:0.5K2O:332H 2O, unreacted anatase and quartz were formed. It was hypothesized that the very low reaction mixture pH of ˜4.1 was responsible for the absence of ETS-10. Therefore, pH of this mixture was modified between ˜6.55-12.75.At low pH of ˜6.55 unreacted anatase was present, while, pH higher than ˜11.24 formed ETS-4 crystals. At an "optimum" pH of ˜11.24 nearly phase-pure ETS-10 crystals were formed. However, these ETS-10 crystals were not small but ˜10-20 mum. This is the first time, that colloidal anatase has been utilized for ETS-10 synthesis.

Antimicrobial activity of TiO2 nanostructures synthesized by hydrothermal method

NASA Astrophysics Data System (ADS)

Surah, Shivani Singh; Sirohi, Siddharth; Nain, Ratyakshi; Kumar, Gulshan

2018-02-01

Titania nanostructures were synthesized by hydrothermal method. Titanium tetrachloride was used as a precursor, sodium hydroxide was used as a solvent. Effect on their morphology by variation of parameters like temperature (110°C, 160°C and 180°C), time (15h,18h, 20h, 22h, 24h) and concentration of the solvent NaOH (5M, 8M, 10 M, 12M) were studied. The obtained TiO2 nanostructures were washed with deionized water. The structure, size, morphology of the prepared nanostructures were analyzed by SEM (scanning electron microscope), DLS (dynamic light scattering), TEM (transmission electron microscope). SEM and TEM revealed the shape, size of the nanostructures. DLS reported the particle size of prepared TiO2 nanoparticles. Polymeric films based on polyvinyl alcohol (PVA) doped with titanium dioxide nanostructures at different weight percentage (0.5, 0.75, 1,2 TiO2/PVA) were prepared using the ultra sonication and solution casting techniques. The appropriate weight of PVA was dissolved in deionized water. The mixture was magnetically stirred continuously and heated (80°C) for 4 hours, until the solution mixture becomes homogenous. Different weight percentage of TiO2 nanostructures were added to deionized water and sonicated for 3 hours to prevent the nanostructures agglomeration. The mixture was mixed with the PVA solution and magnetically stirred for 1 hour to get good dispersion without agglomeration. The final PVA /TiO2 mixture were casted in glass Petridish, were left until dry. Ultrasonication was used as a major factor for preparation in order to get better dispersion. Nanocomposite films were characterized using SEM and were found to exhibit antimicrobial properties when treated with E.coli and pseudomonas.

Solvent effects on infrared spectra of progesterone in CHCl 3/ cyclo-C 6H 12 binary solvent systems

NASA Astrophysics Data System (ADS)

Liu, Qing; Wang, Xiao-yan; Zhang, Hui

2007-01-01

The infrared spectroscopy studies of the C 3 and C 20 carbonyl stretching vibrations ( υ(C dbnd O)) of progesterone in CHCl 3/ cyclo-C 6H 12 binary solvent systems were undertaken to investigate the solute-solvent interactions. With the mole fraction of CHC1 3 in the binary solvent mixtures increase, three types of C 3 and C 20 carbonyl stretching vibration band of progesterone are observed, respectively. The assignments of υ(C dbnd O) of progesterone are discussed in detail. In the CHCl 3-rich binary solvent systems or pure CHCl 3 solvent, two kinds of solute-solvent hydrogen bonding interactions coexist for C 20 C dbnd O. Comparisons are drawn for the solvent sensitivities of υ(C dbnd O) for acetophenone and 5α-androstan-3,17-dione, respectively.

A semisynthesis of 3'-O-ethyl-5,6-dihydrospinosyn J based on the spinosyn A aglycone.

PubMed

Zhang, Kai; Liu, Shenglan; Liu, Anjun; Chai, Hongxin; Li, Jiarong; A, Lamusi

2017-01-01

Spinetoram, a mixture of 3'- O -ethyl-5,6-dihydrospinosyn J (XDE-175-J, major component) and 3'- O -ethylspinosyn L (XDE-175-L, minor component), is a novel kind of green and efficient insecticide with a broad range of action against various insects. Nowadays, spinetoram is widely used in agriculture and food storage. This work reports a 7-step semisynthesis of 3'- O -ethyl-5,6-dihydrospinosyn J from spinosyn A aglycone. The C9-OH and C17-OH of the aglycone are successively connected to 3- O -ethyl-2,4-di- O -methylrhamnose and D-forosamine after selective protection and deprotection steps. Then, with 10% Pd/C as catalyst, the 5,6-double bond of the macrolide was selectively reduced to afford 3'- O -ethyl-5,6-dihydrospinosyn J. In addition, the 3- O -ethyl-2,4-di- O -methylrhamnose is synthesized from rhamnose which is available commercially, while the D-forosamine and aglycone are obtained via the hydrolysis of spinosyn A. High yields were obtained in each step, and all intermediates in the synthesis were characterized by 1 H NMR, 13 C NMR and MS techniques. This study can be helpful for developing an efficient chemical synthesis of spinetoram, and it also offers opportunities to synthesize spinosyn analogues and rhamnose derivatives.

Spectral studies of SiCl4 + N2O + Ar and SiH4 + Ar mixtures in a shock tube in 160-550 nm range

NASA Technical Reports Server (NTRS)

Park, C.; Fujiwara, T.

1978-01-01

Gases containing SiO, SiO2, SiH, and Si2 were produced in the reflected-shock region of a shock tube by heating SiCl4 + N2O + Ar and SiH4 + Ar mixtures with shock waves. Spectral absorption characteristics were measured in the 160-550 nm wavelength range and in the 2800-3600 K temperature range and compared to calculated values. The sums of the squares of electronic transition moments at equilibrium separation were derived. It was found that absorption by SiO2 and other known bands of SiO, SiH, and Si2 were too weak to be measured. The cross section of absorption by a continuum, believed due to SiH, varied from 2.5 x 10 to the -17th sq cm at 280 nm to 1.6 x 10 to the -18th sq cm at 440 nm.

Presentation of an experimental method to induce in vitro ("organ chambers") respiratory acidosis and its effect on vascular reactivity.

PubMed

Nadai, Tales Rubens de; Silveira, Ana Paula Cassiano; Monteiro, Ariadne Santana e Neves; Campos, Debora Ribeiro; Carvalho, Marco Tulio Rezende de; Albuquerque, Agnes Afrodite Sumarelli; Celotto, Andrea Carla; Evora, Paulo Roberto Barbosa

2014-11-01

To create in vitro a model to generate acidosis by CO2 bubbling "organ chambers", which would be useful for researchers that aim to study the effects of acid-base disturbs on the endothelium-dependent vascular reactivity. Eighteen male Wistar rats (230-280 g) were housed, before the experiments, under standard laboratory conditions (12h light/dark cycle at 21°C), with free access to food and water. The protocol for promoting in vitro respiratory acidosis was carried out by bubbling increased concentrations of CO2. The target was to achieve an ideal way to decrease the pH gradually to a value of approximately 6.6.It was used, initially, a gas blender varying concentrations of the carbogenic mixture (95% O2 + 5% CO2) and pure CO2. 1) 100% CO2, pH variation very fast, pH minimum 6.0; 2) 90%CO2 pH variation bit slower, pH minimum 6.31; 3) 70%CO2, pH variation slower, pH minimum 6.32; 4) 50% CO2, pH variation slower, pH minimum 6:42; 5) 40 %CO2, Adequate record, pH minimum 6.61, and; 6) 30 %CO2 could not reach values below pH minimum 7.03. Based on these data the gas mixture (O2 60% + CO2 40%) was adopted. This gas mixture (O2 60% + CO2 40%) was effective in inducing respiratory acidosis at a speed that made, possible the recording of isometric force.

Synthesis, morphology, optical and photocatalytic performance of nanostructured β-Ga{sub 2}O{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Girija, K.; DRDO – BU CLS, Bharathiar University, Coimbatore 641046; Thirumalairajan, S.

2013-06-01

Highlights: ► Nanostructures of β-Ga{sub 2}O{sub 3} were prepared using facile reflux condensation process. ► The pH of the reaction mixture shows evident influence on the size and shape of the nanostructures formed. ► The nanostructures exhibited good photocatalytic activity toward Rhodamine B and was found to be superior for higher pH value. - Abstract: Fine powders of β-Ga{sub 2}O{sub 3} nanostructures were prepared via low temperature reflux condensation method by varying the pH value without using any surfactant. The pH value of reaction mixture had great influence on the morphology of final products. High crystalline single phase β-Ga{sub 2}O{submore » 3} nanostructures were obtained by thermal treatment at 900 °C which was confirmed by X-ray diffraction and Raman spectroscopy. The morphological analysis revealed rod like nanostructures at lower and higher pH values of 6 and 10, while spindle like structures were obtained at pH = 8. The phase purity and presence of vibrational bands were identified using Fourier transform infrared spectroscopy. The optical absorbance spectrum showed intense absorption features in the UV spectral region. A broad blue emission peak centered at 441 nm due to donor–acceptor gallium–oxygen vacancy pair recombination appeared. The photocatalytic activity toward Rhodamine B under visible light irradiation was higher for nanorods at pH 10.« less

Preparation, crystal structure and thermal decomposition kinetics of 1-(2,4-dinitrophenyl)azo-1-nitrocyclohexane

NASA Astrophysics Data System (ADS)

Yang, Desuo; Ma, Haixia; Hu, Rongzu; Song, Jirong; Zhao, Fengqi

2005-11-01

A new three-nitro-group compound of 1-(2,4-dinitrophenyl)azo-1-nitrocyclohexane was prepared by the reaction of cyclohexanone-2,4-dinitrophenylhydrazine with nitric oxide at ambient temperature. The single crystal structure has been determined by a four-circle X-ray diffractometer. The compound is monoclinic with space group P2(1)/ c and unit-cell parameters a=11.300(2) Å, b=12.993(2) Å, c=10.155(1) Å, β=98.33(1) o, F(000)=672, the unit-cell volume V=1475.2(5) Å 3, the molecule number in one unit-cell Z=4, the absorption coefficient μ=1.19 cm -1, the calculated density Dc=1.456 g cm -3. The exothermic decomposition reaction kinetics of the compound has been studied by DSC. The kinetic model function in differential form, apparent activation energy and pre-exponential constant of this reaction are (3/4)(1-α)[-ln(1-α)] 1/4, 123.88 kJ mol -1 and 10 11.49 s -1, respectively. The critical temperature of thermal explosion of the title compound is 161.15 oC and the entropy of activation (ΔS), enthalpy of activation (ΔH), and free energy of activation (ΔG) are -34.16 J mol -1 K -1, 115.7, and 130.48 kJ mol -1, respectively.

Crystal structures of two solvates of (18-crown-6)potassium acetate.

PubMed

Liebing, Phil; Zaeni, Ahmad; Olbrich, Falk; Edelmann, Frank T

2016-12-01

The crystal and mol-ecular strutures of two solvated forms of [K(18 c 6)]OAc (18 c 6 = 18-crown-6 = 1,4,7,10,13,16-hexa-oxa-cyclo-octa-decane and OAc = acetate) were determined by single-crystal X-ray diffraction, namely (acetato-κ 2 O , O ')(1,4,7,10,13,16-hexa-oxa-cyclo-octa-decane-κ 6 O )potassium dihydrate, [K(CH 3 COO)(C 12 H 24 O 6 )]·2H 2 O ( 1 ) and (acetato-κ 2 O , O ')aqua-(1,4,7,10,13,16-hexa-oxa-cyclo-octa-decane-κ 6 O )potassium acetic acid monosolvate [K(CH 3 COO)(C 12 H 24 O 6 )(H 2 O)]·CH 3 COOH ( 2 ). In both compounds, the acetate anion is bonded to the potassium ion in a chelating fashion and the metal atom is consequently slightly displaced from the O 6 plane of the crown ether. In the crystals, O-H⋯O hydrogen bonds lead to a polymeric ladder structure in the dihydrate 1 , while the acetic acid hydrate 2 features inversion dimers.

Pd-catalyzed aerobic oxidative annulation of cyclohexanones and 2-aminophenyl ketones: A direct approach to acridines

NASA Astrophysics Data System (ADS)

Mu, Wanlu; Li, Xiaowei; Wang, Longfei; Chen, Yong; Wu, Yanchao

2017-08-01

An efficient aerobic oxidative annulation of cyclohexanones and 2-aminophenyl ketones approach to substituted acridines, a structural motif for a large number of pharmaceuticals and functional materials is described. The key feature of this method is the use of oxygen as the sole oxidant and Pd catalyst, which resulting in the high regioselectivity with unsymmetrical meta-substituted cyclohexanones. The electron gap of the global redox condensation process is filled and the reaction efficiency is significantly promoted by O2 as a redox moderator. This protocol possesses many advantages such as using O2 as a cheap and nonhazardous oxidant, high regioselectivity and water as the only by-product, which meet the principle of green chemistry.

Ozone and alkyl nitrate formation from the Deepwater Horizon oil spill atmospheric emissions

NASA Astrophysics Data System (ADS)

Neuman, J. A.; Aikin, K. C.; Atlas, E. L.; Blake, D. R.; Holloway, J. S.; Meinardi, S.; Nowak, J. B.; Parrish, D. D.; Peischl, J.; Perring, A. E.; Pollack, I. B.; Roberts, J. M.; Ryerson, T. B.; Trainer, M.

2012-05-01

Ozone (O3), alkyl nitrates (RONO2), and other photochemical products were formed in the atmosphere downwind from the Deepwater Horizon (DWH) oil spill by photochemical reactions of evaporating hydrocarbons with NOx (=NO + NO2) emissions from spill response activities. Reactive nitrogen species and volatile organic compounds (VOCs) were measured from an instrumented aircraft during daytime flights in the marine boundary layer downwind from the area of surfacing oil. A unique VOC mixture, where alkanes dominated the hydroxyl radical (OH) loss rate, was emitted into a clean marine environment, enabling a focused examination of O3 and RONO2 formation processes. In the atmospheric plume from DWH, the OH loss rate, an indicator of potential O3 formation, was large and dominated by alkanes with between 5 and 10 carbons per molecule (C5-C10). Observations showed that NOx was oxidized very rapidly with a 0.8 h lifetime, producing primarily C6-C10 RONO2 that accounted for 78% of the reactive nitrogen enhancements in the atmospheric plume 2.5 h downwind from DWH. Both observations and calculations of RONO2 and O3 production rates show that alkane oxidation dominated O3 formation chemistry in the plume. Rapid and nearly complete oxidation of NOx to RONO2 effectively terminated O3 production, with O3 formation yields of 6.0 ± 0.5 ppbv O3 per ppbv of NOx oxidized. VOC mixing ratios were in large excess of NOx, and additional NOx would have formed additional O3 in this plume. Analysis of measurements of VOCs, O3, and reactive nitrogen species and calculations of O3 and RONO2 production rates demonstrate that NOx-VOC chemistry in the DWH plume is explained by known mechanisms.

Synthetic fluid inclusions in natural quartz I. Compositional types synthesized and applications to experimental geochemistry

NASA Astrophysics Data System (ADS)

Sterner, S. Michael; Bodnar, Robert J.

1984-12-01

Synthetic fluid inclusions having a wide range of geologically applicable compositions in the C-O-H-S-Na-K-Ca-Cl-Cu-Fe system have been formed by healing fractures in inclusion-free natural quartz and by precipitating new quartz overgrowths on an original "seed" crystal. Inclusion types synthesized include: (1) liquid-rich, pure H 2O inclusions of primary and secondary origin, (2) pure H 2O inclusions with the critical density, (3) liquid-rich inclusions containing undersaturated aqueous solutions of NaCl or KCl or CaCl 2, or mixtures of the three salts, (4) H 2O-NaCl inclusions containing halite daughter minerals, (5) H 2O-NaCl-KCl inclusions containing halite and sylvite daughter minerals, (6) H 2O-CO 2 inclusions of various compositions containing liquid H 2O and either CO 2 vapor or CO 2 liquid, or both, at 25°C, (7) H 2O-CO 2-NaCl inclusions containing an aqueous phase, liquid and vapor CO 2, and halite at 25°C, (8) C-O-H inclusions containing liquid H 2O, a CO 2-CH 4 liquid phase and graphite daughter minerals at 25°C, (9) H 2O-NaCl inclusions that contain a chalcopyrite daughter mineral, and (10)inclusions representing trapping of the coexisting, immiscible fluids in the H 2O-NaCl, H 2O-CO 2-NaCl, and Na-C-O-H systems. The inclusions exhibit uniform phase ratios at room temperature, and the temperatures of various phase changes within individual inclusions agree with those predicted from experimental and theoretical data, indicating that the inclusion fluid has the same composition and density as the parent solution. These 'miniature autoclaves' thus may be used to study various problems related to fluid inclusion research, to calibrate analytical equipment used to study natural inclusions, and to study phase equilibria, solubility and PVT relations of a variety of chemical systems.

A combined experimental and theoretical study of the supramolecular self-assembly of the natural benzopyran 2,2-dimethyl-3-hydroxy-6-acetyl-chromane and its isomeric benzofuran 10,11-dihydro-10-hydroxytremetone

NASA Astrophysics Data System (ADS)

Gil, Diego M.; Lizarraga, E.; Echeverría, G. A.; Piro, O. E.; Catalán, C. A. N.; Ben Altabef, A.

2017-10-01

Epoxidation of 4HMBA, the main metabolite of the medicinal plant Sencecionutans, produces an unstable epoxide eventually giving rise to a mixture of four derivatives, three of them previously reported as natural products. The epoxide product easily undergoes an intra-molecular attack of the phenolic hydroxyl against the epoxide group carbons to produce either a benzofuran or a chromane derivative. When dissolved in methanol-water mixture at room temperature the epoxide is completely solvolyzed to give the corresponding diol (hydrolysis) or vicinal hydroxyl-methoxy (methanolysis) derivative. All the compounds involved in the above reactions were characterized by IR, Raman, H NMR and UV-vis spectroscopies, and by mass spectrometry. Density functional theory (DFT) computations were used to optimize the structure conformations. The optimized structures were further subjected to a Natural Bond Orbital (NBO) and electrostatic potentials analysis. The crystal structures of the title compounds (for short, 3 and 4 respectively) were determined by X-ray diffraction methods. Compound 3 crystallizes in the triclinic P-1 space group with a = 6.4289 (6) Å, b = 8.7120 (6) Å, c = 10.952 (1) Å, α = 92.280 (7)°, β = 95.738 (7)°, γ = 103.973 (7)°, and Z = 2 molecules per unit cell and 4 in the monoclinic P21/c space group with a = 11.2891 (6) Å, b = 9.1902 (4) Å, c = 12.4272 (7) Å. Β = 113.689 (7)°, and Z = 4. In 3 neighboring molecules are linked to each other by OH⋯O (keto) bonds giving rise to a polymeric structure. In 4 the OH group is a bifurcate H-bond donor. It forms a weak intra-molecular OH⋯O (furan) bond and also a much stronger inter-molecular Osbnd H⋯O (keto) bond giving rise to a zig-zag polymeric structure. A detailed analysis of the solid state molecular interactions of compounds 3 and 4 has been performed using Hirshfeld surface analysis and their associated 2D fingerprint plots.

Density functional theory and RRKM calculations of decompositions of the metastable E-2,4-pentadienal molecular ions.

PubMed

Solano Espinoza, Eduardo A; Vallejo Narváez, Wilmer E

2010-07-01

The potential energy profiles for the fragmentations that lead to [C(5)H(5)O](+) and [C(4)H(6)](+*) ions from the molecular ions [C(5)H(6)O](+*) of E-2,4-pentadienal were obtained from calculations at the UB3LYP/6-311G + + (3df,3pd)//UB3LYP/6-31G(d,p) level of theory. Kinetic barriers and harmonic frequencies obtained by the density functional method were then employed in Rice-Ramsperger-Kassel-Marcus calculations of individual rate coefficients for a large number of reaction steps. The pre-equilibrium and rate-controlling step approximations were applied to different regions of the complex potential energy surface, allowing the overall rate of decomposition to be calculated and discriminated between three rival pathways: C-H bond cleavage, decarbonylation and cyclization. These processes should have to compete for an equilibrated mixture of four conformers of the E-2,4-pentadienal ions. The direct dissociation, however, can only become important in the high-energy regime. In contrast, loss of CO and cyclization are observable processes in the metastable kinetic window. The former involves a slow 1,2-hydrogen shift from the carbonyl group that is immediately followed by the formation of an ion-neutral complex which, in turn, decomposes rapidly to the s-trans-1,3-butadiene ion [C(4)H(6)](+*). The predominating metastable channel is the second one, that is, a multi-step ring closure which starts with a rate-limiting cis-trans isomerization. This process yields a mixture of interconverting pyran ions that dissociates to the pyrylium ions [C(5)H(5)O](+). These results can be used to rationalize the CID mass spectrum of E-2,4-pentadienal in a low-energy regime. 2010 John Wiley & Sons, Ltd.

Lithiated imines: solvent-dependent aggregate structures and mechanisms of alkylation.

PubMed

Zuend, Stephan J; Ramirez, Antonio; Lobkovsky, Emil; Collum, David B

2006-05-03

We describe efforts to understand the structure and reactivity of lithiated cyclohexanone N-cyclohexylimine. The lithioimine affords complex solvent-dependent distributions of monomers, dimers, and trimers in a number of ethereal solvents. Careful selection of solvent provides exclusively monosolvated dimers. Rate studies on the C-alkylations reveal chronic mixtures of monomer- and dimer-based pathways. We explore the factors influencing reactants and alkylation transition structures and the marked differences between lithioimines and isostructural lithium dialkylamides with the aid of density functional theory calculations.

Self-assembled 3D heterometallic Cu(II)/Fe(II) coordination polymers with octahedral net skeletons: structural features, molecular magnetism, thermal and oxidation catalytic properties.

PubMed

Karabach, Yauhen Y; Guedes da Silva, M Fátima C; Kopylovich, Maximilian N; Gil-Hernández, Beatriz; Sanchiz, Joaquin; Kirillov, Alexander M; Pombeiro, Armando J L

2010-12-06

The new three-dimensional (3D) heterometallic Cu(II)/Fe(II) coordination polymers [Cu(6)(H(2)tea)(6)Fe(CN)(6)](n)(NO(3))(2n)·6nH(2)O (1) and [Cu(6)(Hmdea)(6)Fe(CN)(6)](n)(NO(3))(2n)·7nH(2)O (2) have been easily generated by aqueous-medium self-assembly reactions of copper(II) nitrate with triethanolamine or N-methyldiethanolamine (H(3)tea or H(2)mdea, respectively), in the presence of potassium ferricyanide and sodium hydroxide. They have been isolated as air-stable crystalline solids and fully characterized including by single-crystal X-ray diffraction analyses. The latter reveal the formation of 3D metal-organic frameworks that are constructed from the [Cu(2)(μ-H(2)tea)(2)](2+) or [Cu(2)(μ-Hmdea)(2)](2+) nodes and the octahedral [Fe(CN)(6)](4-) linkers, featuring regular (1) or distorted (2) octahedral net skeletons. Upon dehydration, both compounds show reversible escape and binding processes toward water or methanol molecules. Magnetic susceptibility measurements of 1 and 2 reveal strong antiferromagnetic [J = -199(1) cm(-1)] or strong ferromagnetic [J = +153(1) cm(-1)] couplings between the copper(II) ions through the μ-O-alkoxo atoms in 1 or 2, respectively. The differences in magnetic behavior are explained in terms of the dependence of the magnetic coupling constant on the Cu-O-Cu bridging angle. Compounds 1 and 2 also act as efficient catalyst precursors for the mild oxidation of cyclohexane by aqueous hydrogen peroxide to cyclohexanol and cyclohexanone (homogeneous catalytic system), leading to maximum total yields (based on cyclohexane) and turnover numbers (TONs) up to about 22% and 470, respectively.

Enantioselective desymmetrization of prochiral cyclohexanones by organocatalytic intramolecular Michael additions to α,β-unsaturated esters.

PubMed

Gammack Yamagata, Adam D; Datta, Swarup; Jackson, Kelvin E; Stegbauer, Linus; Paton, Robert S; Dixon, Darren J

2015-04-13

A new catalytic asymmetric desymmetrization reaction for the synthesis of enantioenriched derivatives of 2-azabicyclo[3.3.1]nonane, a key motif common to many alkaloids, has been developed. Employing a cyclohexanediamine-derived primary amine organocatalyst, a range of prochiral cyclohexanone derivatives possessing an α,β-unsaturated ester moiety linked to the 4-position afforded the bicyclic products, which possess three stereogenic centers, as single diastereoisomers in high enantioselectivity (83-99% ee) and in good yields (60-90%). Calculations revealed that stepwise C-C bond formation and proton transfer via a chair-shaped transition state dictate the exclusive endo selectivity and enabled the development of a highly enantioselective primary amine catalyst. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Oxorhenium complexes bearing the water-soluble tris(pyrazol-1-yl)methanesulfonate, 1,3,5-triaza-7-phosphaadamantane, or related ligands, as catalysts for Baeyer-Villiger oxidation of ketones.

PubMed

Martins, Luísa M D R S; Alegria, Elisabete C B A; Smoleński, Piotr; Kuznetsov, Maxim L; Pombeiro, Armando J L

2013-04-15

New rhenium(VII or III) complexes [ReO3(PTA)2][ReO4] (1) (PTA = 1,3,5-triaza-7-phosphaadamantane), [ReO3(mPTA)][ReO4]I (2) (mPTA = N-methyl-1,3,5-triaza-7-phosphaadamantane cation), [ReO3(HMT)2][ReO4] (3) (HMT = hexamethylenetetramine), [ReO3(η(2)-Tpm)(PTA)][ReO4] (4) [Tpm = hydrotris(pyrazol-1-yl)methane, HC(pz)3, pz = pyrazolyl], [ReO3(Hpz)(HMT)][ReO4] (5) (Hpz = pyrazole), [ReO(Tpms)(HMT)] (6) [Tpms = tris(pyrazol-1-yl)methanesulfonate, O3SC(pz)3(-)] and [ReCl2{N2C(O)Ph}(PTA)3] (7) have been prepared from the Re(VII) oxide Re2O7 (1-6) or, in the case of 7, by ligand exchange from the benzoyldiazenido complex [ReCl2{N2C(O)Ph}(Hpz)(PPh3)2], and characterized by IR and NMR spectroscopies, elemental analysis and electrochemical properties. Theoretical calculations at the density functional theory (DFT) level of theory indicated that the coordination of PTA to both Re(III) and Re(VII) centers by the P atom is preferable compared to the coordination by the N atom. This is interpreted in terms of the Re-PTA bond energy and hard-soft acid-base theory. The oxo-rhenium complexes 1-6 act as selective catalysts for the Baeyer-Villiger oxidation of cyclic and linear ketones (e.g., 2-methylcyclohexanone, 2-methylcyclopentanone, cyclohexanone, cyclopentanone, cyclobutanone, and 3,3-dimethyl-2-butanone or pinacolone) to the corresponding lactones or esters, in the presence of aqueous H2O2. The effects of a variety of factors are studied toward the optimization of the process.

TNT Equivalency Testing of Chemical Mixtures in Continuous TNT Manufacturing

DTIC Science & Technology

1980-08-01

RONALD RAPE JOSEPH MAVEC RICHARD JOYCE IIT RESEARCH INSTITUTE 10 WEST35TH STREET CHICAGO. IL 60616 PAUL PRICE. PROJECT LEADER ARRADCOM. DOVER. NEW...AUTHORfs; Ronald Pape, Joseph Mavec, Richard Joyce, IIT Research Institute Paul Price, Project Leader, ARRADCOM 8. CONTRACT OR GRANT NUMBERfs...r-4 (0 ^ o s •H ^ <U XI 4J C-H •r4 1-1 i-l 1-1 >. a; X) U to •rl U «c U-l o 60 C *J •H C x m^: •^ E c B 4J CC M 4-J 4-1

Solid State Synthesis and Properties of Monoclinic Celsian

NASA Technical Reports Server (NTRS)

Bansal, Narottam P.

1996-01-01

Monoclinic celsian of Ba(0.75)Sr(0.25)Al2Si2O8 (BSAS-1) and B(0.85)Sr(O.15)Al2Si2O8 (BSAS-2) compositions have been synthesized from metal carbonates and oxides by solid state reaction. A mixture of BaCO3, SrCO3, Al2O3, and SiO2 powders was precalcined at approx. 900-940 C to decompose the carbonates followed by hot pressing at approx. 1300 C. The hot pressed BSAS-1 material was almost fully dense and contained the monoclinic celsian phase, with complete absence of the undesirable hexacelsian as indicated by x-ray diffraction. In contrast, a small fraction of hexacelsian was still present in hot pressed BSAS-2. However, on further heat treatment at 1200 C for 24 h, the hexacelsian phase was completely eliminated. The average linear thermal expansion coefficients of BSAS-1 and BSAS-2 compositions, having the monoclinic celsian phase, were measured to be 5.28 x 10(exp -6)/deg C and 5.15 x 10(exp -6)/deg C, respectively from room temperature to 1200 C. The hot pressed BSAS-1 celsian showed room temperature flexural strength of 131 MPa, elastic modulus of 96 GPa and was stable in air up to temperatures as high as approx. 1500 C.

Unimolecular Thermal Fragmentation of Ortho-Benzyne

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, X.; Maccarone, A. T.; Nimlos, M. R.

2007-01-01

The ortho-benzyne diradical, o-C{sub 6}H{sub 4} has been produced with a supersonic nozzle and its subsequent thermal decomposition has been studied. As the temperature of the nozzle is increased, the benzyne molecule fragments: o-C{sub 6}H{sub 4} + {Delta} {yields} products. The thermal dissociation products were identified by three experimental methods: (i) time-of-flight photoionization mass spectrometry, (ii) matrix-isolation Fourier transform infrared absorption spectroscopy, and (iii) chemical ionization mass spectrometry. At the threshold dissociation temperature, o-benzyne cleanly decomposes into acetylene and diacetylene via an apparent retro-Diels-Alder process: o-C{sub 6}H{sub 4} + {Delta} {yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH. The experimentalmore » {Delta}{sub rxn}H{sub 298}(o-C{sub 6}H{sub 4} {yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH) is found to be 57 {+-} 3 kcal mol{sup -1}. Further experiments with the substituted benzyne, 3,6-(CH{sub 3}){sub 2}-o-C{sub 6}H{sub 2}, are consistent with a retro-Diels-Alder fragmentation. But at higher nozzle temperatures, the cracking pattern becomes more complicated. To interpret these experiments, the retro-Diels-Alder fragmentation of o-benzyne has been investigated by rigorous ab initio electronic structure computations. These calculations used basis sets as large as [C(7s6p5d4f3g2h1i)/H(6s5p4d3f2g1h)] (cc-pV6Z) and electron correlation treatments as extensive as full coupled cluster through triple excitations (CCSDT), in cases with a perturbative term for connected quadruples [CCSDT(Q)]. Focal point extrapolations of the computational data yield a 0 K barrier for the concerted, C{sub 2v}-symmetric decomposition of o-benzyne, E{sub b}(o-C{sub 6}H{sub 4} {yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH) = 88.0 {+-} 0.5 kcal mol{sup -1}. A barrier of this magnitude is consistent with the experimental results. A careful assessment of the thermochemistry for the high temperature fragmentation of benzene is presented: C{sub 6}H{sub 6} {yields} H+[C{sub 6}H{sub 5}] {yields} H+[o-C{sub 6}H{sub 4}] {yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH. Benzyne may be an important intermediate in the thermal decomposition of many alkylbenzenes (arenes). High engine temperatures above 1500 K may crack these alkylbenzenes to a mixture of alkyl radicals and phenyl radicals. The phenyl radicals will then dissociate first to benzyne and then to acetylene and diacetylene.« less

Unimolecular thermal fragmentation of ortho-benzene.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, X.; Maccarone, A. T.; Nimlos, M. R.

2007-01-01

The ortho-benzyne diradical, o-C{sub 6}H{sub 4} has been produced with a supersonic nozzle and its subsequent thermal decomposition has been studied. As the temperature of the nozzle is increased, the benzyne molecule fragments o-C{sub 6}H{sub 4}{sup +} {Delta} {yields} products. The thermal dissociation products were identified by three experimental methods: (i) time-of-flight photoionization mass spectrometry, (ii) matrix-isolation Fourier transform infrared absorption spectroscopy, and (iii) chemical ionization mass spectrometry. At the threshold dissociation temperature, o-benzyne cleanly decomposes into acetylene and diacetylene via an apparent retro-Diels-Alder process: o-C{sub 6}H{sub 4}{sup +}{Delta}{yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH. The experimental {Delta}{sub rxn}H{submore » 298}(o-C{sub 6}H{sub 4} {yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH) is found to be 57 {+-} 3 kcal mol{sup -1}. Further experiments with the substituted benzyne, 3,6-(CH{sub 3}){sub 2}-o-C{sub 6}H{sub 2}, are consistent with a retro-Diels-Alder fragmentation. But at higher nozzle temperatures, the cracking pattern becomes more complicated. To interpret these experiments, the retro-Diels-Alder fragmentation of o-benzyne has been investigated by rigorous ab initio electronic structure computations. These calculations used basis sets as large as [C(7s6p5d4f3g2h1i)/H(6s5p4d3f2g1h)] (cc-pV6Z) and electron correlation treatments as extensive as full coupled cluster through triple excitations (CCSDT), in cases with a perturbative term for connected quadruples [CCSDT(Q)]. Focal point extrapolations of the computational data yield a 0 K barrier for the concerted, C{sub 2v}-symmetric decomposition of o-benzyne, E{sub b}(o-C{sub 6}H{sub 4} {yields} HC {triple_bond} CH+HC {triple_bond} C-C {triple_bond} CH) = 88.0 {+-} 0.5 kcal mol{sup -1}. A barrier of this magnitude is consistent with the experimental results. A careful assessment of the thermochemistry for the high temperature fragmentation of benzene is presented: C{sub 6}H{sub 6} {yields} H+[C{sub 6}H{sub 5}] {yields} H+[o-C{sub 6}H{sub 4}] {yields} HC {triple_bond} CH-HC {triple_bond} C-C {triple_bond} CH. Benzyne may be an important intermediate in the thermal decomposition of many alkylbenzenes (arenes). High engine temperatures above 1500 K may crack these alkylbenzenes to a mixture of alkyl radicals and phenyl radicals. The phenyl radicals will then dissociate first to benzyne and then to acetylene and diacetylene.« less

Decomposition Mechanism of C5F10O: An Environmentally Friendly Insulation Medium.

PubMed

Zhang, Xiaoxing; Li, Yi; Xiao, Song; Tang, Ju; Tian, Shuangshuang; Deng, Zaitao

2017-09-05

SF 6 , the most widely used electrical-equipment-insulation gas, has serious greenhouse effects. C 5 F 10 O has attracted much attention as an alternative gas in recent two years, but the environmental impact of its decomposition products is unclear. In this work, the decomposition characteristics of C 5 F 10 O were studied based on gas chromatography-mass spectrometry and density functional theory. We found that the amount of decomposition products of C 5 F 10 O, namely, CF 4 , C 2 F 6 , C 3 F 6 , C 3 F 8 , C 4 F 10 , and C 6 F 14 , increased with increased number of discharges. Under a high-energy electric field, the C-C bond of C 5 F 10 O between carbonyl carbon and α-carbon atoms was most likely to break and generate CF 3 CO•, C 3 F 7 • or C 3 F 7 CO•, CF 3 • free radicals. CF 3 •, and C 3 F 7 • free radicals produced by the breakage more easily recombined to form small molecular products. By analyzing the ionization parameters, toxicity, and environmental effects of C 5 F 10 O and its decomposition products, we found that C 5 F 10 O gas mixtures exhibit great decomposition and environmental characteristics with low toxicity, with great potential to replace SF 6 .

Novel nano-semiconductor film layer supported nano-Pd Complex Nanostructured Catalyst Pd/Ⓕ-MeOx/AC for High Efficient Selective Hydrogenation of Phenol to Cyclohexanone.

PubMed

Si, Jiaqi; Ouyang, Wenbing; Zhang, Yanji; Xu, Wentao; Zhou, Jicheng

2017-04-28

Supported metal as a type of heterogeneous catalysts are the most widely used in industrial processes. High dispersion of the metal particles of supported catalyst is a key factor in determining the performance of such catalysts. Here we report a novel catalyst Pd/Ⓕ-MeO x /AC with complex nanostructured, Pd nanoparticles supported on the platelike nano-semiconductor film/activated carbon, prepared by the photocatalytic reduction method, which exhibited high efficient catalytic performance for selective hydrogenation of phenol to cyclohexanone. Conversion of phenol achieved up to more than 99% with a lower mole ratio (0.5%) of active components Pd and phenol within 2 h at 70 °C. The synergistic effect of metal nanoparticles and nano-semiconductors support layer and the greatly increasing of contact interface of nano-metal-semiconductors may be responsible for the high efficiency. This work provides a clear demonstration that complex nanostructured catalysts with nano-metal and nano-semiconductor film layer supported on high specific surface AC can yield enhanced catalytic activity and can afford promising approach for developing new supported catalyst.

Effects of molten-salt/ionic-liquid mixture on extraction of docosahexaenoic acid (DHA)-rich lipids from Aurantiochytrium sp. KRS101.

PubMed

Choi, Sun-A; Jung, Joo-Young; Kim, Kyochan; Kwon, Jong-Hee; Lee, Jin-Suk; Kim, Seung Wook; Park, Ji-Yeon; Yang, Ji-Won

2014-11-01

In this study, lipid extraction from Aurantiochytrium sp. was performed using a molten-salt/ionic-liquid mixture. The total fatty acid content of Aurantiochytrium sp. was 478.8 mg/g cell, from which 145 mg/g cell (30.3% of total fatty acids) of docosahexaenoic acid (DHA) was obtained. FeCl3·6H2O showed a high lipid extraction yield (207.9 mg/g cell), when compared with that of [Emim]OAc, which was only 118.1 mg/g cell; notably however, when FeCl3·6H2O was mixed with [Emim]OAc (5:1, w/w), the yield was increased to 478.6 mg/g cell. When lipid was extracted by the FeCl3·6H2O/[Emim]OAc mixture at a 5:1 (w/w) blending ratio under 90 °C, 30 min reaction conditions, the fatty acid content of the extracted lipid was a high purity 997.7 mg/g lipid, with most of the DHA having been extracted (30.2% of total fatty acids). Overall, lipid extraction from Aurantiochytrium sp. was enhanced by the synergistic effects of the molten-salt/ionic-liquid mixture with different ions.

Absorption of Carbon Dioxide in Aqueous Solutions of N-methyldiethanolamine Mixtures

NASA Astrophysics Data System (ADS)

Ma’mun, S.; Svendsen, H. F.

2018-05-01

Carbon dioxide (CO2) is one of the greenhouse gases (GHG) that has contributed to the global warming problem. Carbon dioxide is produced in large quantity from coal-fired power plants, iron and steel production, cement production, chemical and petrochemical industries, natural gas purification, and transportation. Some efforts to reduce the CO2 emissions to the atmosphere are then required. Amine-based absorption may be an option for post-combustion capture. The objective of this study is to measure the effect of promoter addition as well as MDEA concentration for the CO2 absorption into the aqueous solutions of MDEA to improve its performances, i.e. increasing the absorption rate and the absorption capacity. Absorption of CO2 in aqueous solutions of MDEA mixtures were measured at 40 °C in a bubble tank reactor. The systems tested were the mixtures of 30 wt% MDEA with 5 and 10 wt% BEA and the mixtures of 40 and 50 wt% MDEA with 6 wt% AEEA. It was found that for MDEA-BEA-H2O mixtures, the higher the promoter concentraation the higher the CO2 absorption rate, while for the MDEA-AEEA-H2O mixtures, the higher the MDEA concentration the lower the CO2 absorption rate.

Phospa-s-Triazines and Related Compositions of Improved Hydrolytic and Thermal Stability

NASA Technical Reports Server (NTRS)

Paciorek, K. J. L.

1996-01-01

The objective of the Program was to synthesize novel degradation inhibitors for perfluoropolyalkylether fluids and to evaluate their performance as well as that of other available inhibitors. Four novel additives: (C3F7OCF(CF3)CF2OC(CF3)2CN)((C6H5)2PN)2, (C3F7O(CF(CF3)CF2O)2C(CF3)2CN)((C6H5)2PN)2, u-(C3F7OCF(CF3)CF2OC(CF3)2CN)2((C6H5)2PN)2 and C3F7(OCF(CF3)CF2)6C6H4OP(O)(OC6H5)2 were prepared, characterized and their thermal stabilities established. The alloys studied were: 440C steel, M-50 steel, Pyrowear 675, Cronidur 30, Ti (4Al, 4Mn), and Ti (6Al, 4V). The additives and metals were evaluated in two different lots of Fomblin Z25, in Krytox 143AC and in Krytox 16256. Phosphate esters were found to be fully effective in arresting perfluoropolyaucylether fluid's degradation at temperatures up to 300 C over 24 h in the presence of alloys in oxygen. The overall rating of additives was: phosphates greater than phosphate/diester mixture greater than phosphine grater vthan or equal to phpospha-s-triazines.

Thermodynamics of formation for the 18-crown-6-triglycine molecular complex in water-dimethylsulfoxide solvents

NASA Astrophysics Data System (ADS)

Usacheva, T. R.; Lan, Pham Thi; Sharnin, V. A.

2014-06-01

The effect of a water-dimethylsulfoxide (DMSO) solvent on the formation of a molecular complex of 18-crown-6 (18C6) with triglycine (diglycylglycine, 3Gly) is studied via calorimetric titration. It is found that switching from water to an H2O-DMSO mixture with DMSO mole fraction of 0.30 is accompanied by a monotonic increase in the stability of [3Gly18C6] complex, from log K ∘ = 1.10 to log K ∘ = 2.44, and an increase in the exothermicity of the reaction of its formation, from -5.9 to -16.9 kJ/mol. It is shown that the [3Gly18C6] complex exhibits enthalpy stabilization with negative values of enthalpy and entropy over the investigated range of H2O-DMSO solvents. Analysis of the reagents' solvation characteristics reveals that the increase in the reaction's exothermicity of transfer is due to differences in the solvation of [3Gly18C6] and 18C6 with a small solvation contribution from 3Gly. It is concluded that the change in the Gibbs energy of the reaction 3Glysolv + 18C6solv ↔ [3Gly18C6]solv is due to differences in the change in the solvation state of the complex and the peptide (Δtr G ∘([3Gly18C6])-Δtr G ∘(3Gly)).

Monitoring a simple hydrolysis process in an organic solid by observing methyl group rotation.

PubMed

Beckmann, Peter A; Bohen, Joseph M; Ford, Jamie; Malachowski, William P; Mallory, Clelia W; Mallory, Frank B; McGhie, Andrew R; Rheingold, Arnold L; Sloan, Gilbert J; Szewczyk, Steven T; Wang, Xianlong; Wheeler, Kraig A

2017-09-01

We report a variety of experiments and calculations and their interpretations regarding methyl group (CH 3 ) rotation in samples of pure 3-methylglutaric anhydride (1), pure 3-methylglutaric acid (2), and samples where the anhydride is slowly absorbing water from the air and converting to the acid [C 6 H 8 O 3 (1) + H 2 O → C 6 H 10 O 4 (2)]. The techniques are solid state 1 H nuclear magnetic resonance (NMR) spin-lattice relaxation, single-crystal X-ray diffraction, electronic structure calculations in both isolated molecules and in clusters of molecules that mimic the crystal structure, field emission scanning electron microscopy, differential scanning calorimetry, and high resolution 1 H NMR spectroscopy. The solid state 1 H spin-lattice relaxation experiments allow us to observe the temperature dependence of the parameters that characterize methyl group rotation in both compounds and in mixtures of the two compounds. In the mixtures, both types of methyl groups (that is, molecules of 1 and 2) can be observed independently and simultaneously at low temperatures because the solid state 1 H spin-lattice relaxation is appropriately described by a double exponential. We have followed the conversion 1 → 2 over periods of two years. The solid state 1 H spin-lattice relaxation experiments in pure samples of 1 and 2 indicate that there is a distribution of NMR activation energies for methyl group rotation in 1 but not in 2 and we are able to explain this in terms of the particle sizes seen in the field emission scanning electron microscopy images. Copyright © 2017 Elsevier Inc. All rights reserved.

Kinetics of calcium sulfoaluminate formation from tricalcium aluminate, calcium sulfate and calcium oxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xuerun, E-mail: xuerunli@163.com; Zhang, Yu; Shen, Xiaodong, E-mail: xdshen@njut.edu.cn

The formation kinetics of tricalcium aluminate (C{sub 3}A) and calcium sulfate yielding calcium sulfoaluminate (C{sub 4}A{sub 3}more » $$) and the decomposition kinetics of calcium sulfoaluminate were investigated by sintering a mixture of synthetic C{sub 3}A and gypsum. The quantitative analysis of the phase composition was performed by X-ray powder diffraction analysis using the Rietveld method. The results showed that the formation reaction 3Ca{sub 3}Al{sub 2}O{sub 6} + CaSO{sub 4} → Ca{sub 4}Al{sub 6}O{sub 12}(SO{sub 4}) + 6CaO was the primary reaction < 1350 °C with and activation energy of 231 ± 42 kJ/mol; while the decomposition reaction 2Ca{sub 4}Al{sub 6}O{sub 12}(SO{sub 4}) + 10CaO → 6Ca{sub 3}Al{sub 2}O{sub 6} + 2SO{sub 2} ↑ + O{sub 2} ↑ primarily occurred beyond 1350 °C with an activation energy of 792 ± 64 kJ/mol. The optimal formation region for C{sub 4}A{sub 3}$$ was from 1150 °C to 1350 °C and from 6 h to 1 h, which could provide useful information on the formation of C{sub 4}A{sub 3}$ containing clinkers. The Jander diffusion model was feasible for the formation and decomposition of calcium sulfoaluminate. Ca{sup 2+} and SO{sub 4}{sup 2−} were the diffusive species in both the formation and decomposition reactions. -- Highlights: •Formation and decomposition of calcium sulphoaluminate were studied. •Decomposition of calcium sulphoaluminate combined CaO and yielded C{sub 3}A. •Activation energy for formation was 231 ± 42 kJ/mol. •Activation energy for decomposition was 792 ± 64 kJ/mol. •Both the formation and decomposition were controlled by diffusion.« less

X-ray mapping in heterocyclic design: 18. X-ray diffraction study of a series of derivatives of 3-cyanopyridine-2-one with annelated heptane and octane cycles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rybakov, V. B., E-mail: Rybakov20021@yandex.ru; Babaev, E. V.; Paronikyan, E. G., E-mail: Ervand.paronikyan@mail.ru

Seven new, previously unknown, bicyclic and tricyclic heterocycles based on derivatives of 3-cyanopyrid-2-ones are obtained: 2-oxo-2,5,6,7,8,9-hexahydro-1H-cyclohepta[b]pyridine-3-carbonitrile, C{sub 11}H{sub 12}N{sub 2}O (1a); 2-[2-(4-chlorophenyl)-2-oxoethoxy]-6,7,8,9-tetrahydro-5H-cyclohepta[b] pyridine-3-carbonitrile, C{sub 19}H{sub 17}ClN{sub 2}O{sub 2} (2a); (3-amino-6,7,8,9-tetrahydro-5H-cyclohepta[b]furo[3,2-e]pyridin-2-yl)(4- chlorophenyl)methanone, C{sub 19}H{sub 17}ClN{sub 2}O{sub 2} (3); 2-oxo-1,2,5,6,7,8,9,10-octahydrocycloocta[b]pyridine-3-carboxamide, C{sub 12}H{sub 16}N{sub 2}O{sub 2} (4); 2-[2-(4-chorophenyl)-2-oxoethoxy]-5,6,7,8,9,10 -hexahydrocycloocta[b]pyridine-3-carboxamide, C{sub 20}H{sub 21}ClN{sub 2}O{sub 3} (5a); 1-[2-(4-chlorophenyl)-2-oxoethyl]-2-oxo-1,2,5,6,7,8,9,10 -octahydrocycloocta[b]pyridine-3-carboxamide, C{sub 20}H{sub 21}ClN{sub 2}O{sub 3} (5b); and 2-[2-(4-chlorophenyl)-2-oxoethoxy]-5,6,7,8,9,10-hexahydrocycloocta[b] pyridine-3-carbonitrile, C{sub 20}H{sub 19}ClN{sub 2}O{sub 2}, (6). All compounds are characterized by {sup 1}H NMR spectroscopy, and their crystal structures are determined by X-ray diffraction.

Enhanced CO2 capture in binary mixtures of 1-alkyl-3-methylimidazolium tricyanomethanide ionic liquids with water.

PubMed

Romanos, George E; Zubeir, Lawien F; Likodimos, Vlassis; Falaras, Polycarpos; Kroon, Maaike C; Iliev, Boyan; Adamova, Gabriela; Schubert, Thomas J S

2013-10-10

Absorption of carbon dioxide and water in 1-butyl-3-methylimidazoliun tricyanomethanide ([C4C1im][TCM]) and 1-octyl-3-methylimidazolium tricyanomethanide ([C8C1im][TCM]) ionic liquids (ILs) was systematically investigated for the first time as a function of the H2O content by means of a gravimetric system together with in-situ Raman spectroscopy, excess molar volume (V(E)), and viscosity deviation measurements. Although CO2 absorption was marginally affected by water at low H2O molar fractions for both ILs, an increase of the H2O content resulted in a marked enhancement of both the CO2 solubility (ca. 4-fold) and diffusivity (ca. 10-fold) in the binary [C(n)C1im][TCM]/H2O systems, in contrast to the weak and/or detrimental influence of water in most physically and chemically CO2-absorbing ILs. In-situ Raman spectroscopy on the IL/CO2 systems verified that CO2 is physically absorbed in the dry ILs with no significant effect on their structural organization. A pronounced variation of distinct tricyanomethanide Raman modes was disclosed in the [C(n)C1im][TCM]/H2O mixtures, attesting to the gradual disruption of the anion-cation coupling by the hydrogen-bonded water molecules to the [TCM](-) anions, in accordance with the positive excess molar volumes and negative viscosity deviations for the binary systems. Most importantly, CO2 absorption in the ILs/H2O mixtures at high water concentrations revealed that the [TCM](-) Raman modes tend to restore their original state for the heavily hydrated ILs, in qualitative agreement with the intriguing nonmonotonous transients of CO2 absorption kinetics unveiled by the gravimetric measurements for the hybrid solvents. A molecular exchange mechanism between CO2 in the gas phase and H2O in the liquid phase was thereby proposed to explain the enhanced CO2 absorption in the hybrid [C(n)C1im][TCM]//H2O solvents based on the subtle competition between the TCM-H2O and TCM-CO2 interactions, which renders these ILs very promising for CO2 separation applications.

Caprine blastocyst formation following intracytoplasmic sperm injection and defined culture.

PubMed

Keskintepe, L; Morton, P C; Smith, S E; Tucker, M J; Simplicio, A A; Brackett, B G

1997-08-01

Experiments were undertaken to develop intracytoplasmic sperm injection (ICSI) to produce caprine embryos out of the normal breeding season. Oocytes were obtained from 2-6 mm ovarian follicles at slaughter. Selected oocytes with two to four layers of cumulus cells were incubated in 1 ml of H-TCM199 supplemented with 10 micrograms each of oFSH and bLH (NHPP, NIDDK, NICHD, USDA) and 20% fetal bovine serum (FBS) in a thermos (38.5 degrees C) for 4.5 h during transportation. Then, oocytes were transferred into 75 microliters of freshly prepared maturation medium under paraffin oil and a mixture of 5% O2, 5% CO2 and 90% N2. Approximately 26 h after recovery oocytes were denuded by incubation with hyaluronidase (100 IU/ml) and pipetting and held at 38.5 degrees C for 90 min. Spermatozoa frozen in egg yolk extender were thawed in a 37 degrees C water bath for 15 s. Motile fractions were selected by swim-up, then incubated for 90 min in TALP with 10 micrograms heparin/ml. Each oocyte was positioned with its first polar body at 6 or 12 o'clock by a holding pipette. Sperm (1 microliter) were added to 10 microliters medium containing 10% polyvinylpyrrolidone. A sperm cell was aspirated into a pipette, and then injected head-first into the cytoplasm of an oocyte maintained in H-TCM199 + 20% FBS at 37 degrees C. Injected oocytes were transferred to HM and, after 90 min, cultured in 50 microliters of BSA-free synthetic oviduct fluid plus polyvinyl alcohol, citrate and non-essential amino acids. Results demonstrate that caprine blastocysts can be produced outside the breeding season by the use of frozen-thawed semen and injection of sperm cells with broken tails into ova followed by culture in defined medium.

Entropy and the Homogeneity of Solid Mixtures

DTIC Science & Technology

1988-02-01

TRANSLOCATION OF POINTS FROM THE NINE SAMPLES INTO A 6x6 MATRIX 14 NSWC TR 86.440 E .- CF cN C! -rn N" FIUR 10 NRPNUFC O NIELDSRBTO NTENN APE C, -15...Walter) 10 800 N. Quincy Street, BCT 1 (A. Campolattaro) 10 Arlington, VA 22217-5000 R16 (R. Bazil) 1 (G. Wilmot ) 1 Commander (S. Deiter) 1 Naval Weapons

Formation of Amino Acids and Nucleotide Bases in a Titan Atmosphere Simulation Experiment

PubMed Central

Yelle, R.V.; Buch, A.; Carrasco, N.; Cernogora, G.; Dutuit, O.; Quirico, E.; Sciamma-O'Brien, E.; Smith, M.A.; Somogyi, Á.; Szopa, C.; Thissen, R.; Vuitton, V.

2012-01-01

Abstract The discovery of large (>100 u) molecules in Titan's upper atmosphere has heightened astrobiological interest in this unique satellite. In particular, complex organic aerosols produced in atmospheres containing C, N, O, and H, like that of Titan, could be a source of prebiotic molecules. In this work, aerosols produced in a Titan atmosphere simulation experiment with enhanced CO (N2/CH4/CO gas mixtures of 96.2%/2.0%/1.8% and 93.2%/5.0%/1.8%) were found to contain 18 molecules with molecular formulae that correspond to biological amino acids and nucleotide bases. Very high-resolution mass spectrometry of isotopically labeled samples confirmed that C4H5N3O, C4H4N2O2, C5H6N2O2, C5H5N5, and C6H9N3O2 are produced by chemistry in the simulation chamber. Gas chromatography–mass spectrometry (GC-MS) analyses of the non-isotopic samples confirmed the presence of cytosine (C4H5N3O), uracil (C5H4N2O2), thymine (C5H6N2O2), guanine (C5H5N5O), glycine (C2H5NO2), and alanine (C3H7NO2). Adenine (C5H5N5) was detected by GC-MS in isotopically labeled samples. The remaining prebiotic molecules were detected in unlabeled samples only and may have been affected by contamination in the chamber. These results demonstrate that prebiotic molecules can be formed by the high-energy chemistry similar to that which occurs in planetary upper atmospheres and therefore identifies a new source of prebiotic material, potentially increasing the range of planets where life could begin. Key Words: Astrochemistry—Planetary atmospheres—Titan—Astrobiology. Astrobiology 12, 809–817. PMID:22917035

Carbon deposition thresholds on nickel-based solid oxide fuel cell anodes I. Fuel utilization

NASA Astrophysics Data System (ADS)

Kuhn, J.; Kesler, O.

2015-03-01

In the first of a two part publication, the effect of fuel utilization (Uf) on carbon deposition rates in solid oxide fuel cell nickel-based anodes was studied. Representative 5-component CH4 reformate compositions (CH4, H2, CO, H2O, & CO2) were selected graphically by plotting the solutions to a system of mass-balance constraint equations. The centroid of the solution space was chosen to represent a typical anode gas mixture for each nominal Uf value. Selected 5-component and 3-component gas mixtures were then delivered to anode-supported cells for 10 h, followed by determination of the resulting deposited carbon mass. The empirical carbon deposition thresholds were affected by atomic carbon (C), hydrogen (H), and oxygen (O) fractions of the delivered gas mixtures and temperature. It was also found that CH4-rich gas mixtures caused irreversible damage, whereas atomically equivalent CO-rich compositions did not. The coking threshold predicted by thermodynamic equilibrium calculations employing graphite for the solid carbon phase agreed well with empirical thresholds at 700 °C (Uf ≈ 32%); however, at 600 °C, poor agreement was observed with the empirical threshold of ∼36%. Finally, cell operating temperatures correlated well with the difference in enthalpy between the supplied anode gas mixtures and their resulting thermodynamic equilibrium gas mixtures.

Thermodynamic characterization of three polymorphic forms of piracetam.

PubMed

Picciochi, Ricardo; Diogo, Hermínio P; da Piedade, Manuel E Minas

2011-02-01

Combustion calorimetry, solution calorimetry, and differential scanning calorimetry (DSC) were used to determine the standard (p° = 0.1 MPa) molar enthalpies of formation of Forms I, II, and III piracetam at 298.15 K, namely, Δ(f) H(m)° (C(6)H(10)O(2)N(2), cr I) = -520.6 ± 1.6 kJ·mol(-1), Δ(f) H(m)° (C(6)H(10)O(2)N(2), cr II) = -523.8 ± 1.6 kJ·mol(-1), and Δ(f) H(m)° (C(6)H(10)O(2)N(2), cr III) = -524.1 ± 1.6 kJ·mol(-1). The enthalpy of formation of gaseous piracetam at 298.15 K was also derived as Δ(f) H(m)° (C(6)H(10)O(2)N(2), g) = -401.3 ± 2.1 kJ·mol(-1), by combining the standard molar enthalpy of formation of Form II piracetam with the corresponding enthalpy of sublimation, Δ(sub) H(m)° (C(6) H(10) O(2) N(2), cr II) = 122.5 ± 1.4 kJ·mol(-1), obtained by drop-sublimation Calvet microcalorimetry and the Knudsen effusion method. The Δ(f) H(m)° (C(6)H(10)O(2)N(2), g) value was used to assess the corresponding predictions by the B3LYP/cc-pVTZ (-335.3 kJ·mol(-1)), G3MP2 (-388.7 kJ·mol(-1)), and CBS-QB3 (-402.8 kJ·mol(-1)) methods, based on the calculation of the atomization enthalpy of piracetam. Finally, the results of the solution and DSC experiments indicate that the stability hierarchy of Forms I, II, and III piracetam at 298.15 K, for which there was conflicting evidence in the literature, is III > II > I. Copyright © 2010 Wiley-Liss, Inc.

Highly efficient indoor air purification using adsorption-enhanced-photocatalysis-based microporous TiO2 at short residence time.

PubMed

Lv, Jinze; Zhu, Lizhong

2013-01-01

A short residence time is a key design parameter for the removal of organic pollutants in catalyst-based indoor air purification systems. In this study, we synthesized a series of TiO2 with different micropore volumes and studied their removal efficiency of indoor carbonyl pollutants at a short residence time. Our results indicated that the superior adsorption capability of TiO2 with micropores improved its performance in the photocatalytic degradation of cyclohexanone, while the photocatalytic removal of the pollutant successfully kept porous TiO2 from becoming saturated. When treated with 1 mg m(-3) cyclohexanone at a relatively humidity of 18%, the adsorption amount on microporous TiO2 was 5.4-7.9 times higher than that on P25. Removal efficiency via photocatalysis followed'the same order as the adsorption amount: TiO2-5 > TiO2-20 > TiO2-60 > TiO2-180 > P25. The advantage of microporous TiO2 over P25 became more pronounced when the residence time declined from 0.072 to 0.036 s. Moreover, as the concentration of cyclohexanone deceased from 1000 ppb to 500 ppb, removal efficiency by microporous TiO2 increased more rapidly than P25.

Neutronics Benchmarks for the Utilization of Mixed-Oxide Fuel: Joint U.S./ Russian Progress Report for Fiscal Year 1997, Volume 4, Part 8 - Neutron Poison Plates in Assemblies Containing Homogeneous Mixtures of Polystyrene-Moderated Plutonium and Uranium Oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yavuz, M.

1999-05-01

In the 1970s at the Battelle Pacific Northwest Laboratory (PNL), a series of critical experiments using a remotely operated Split-Table Machine was performed with homogeneous mixtures of (Pu-U)O{sub 2}-polystyrene fuels in the form of square compacts having different heights. The experiments determined the critical geometric configurations of MOX fuel assemblies with and without neutron poison plates. With respect to PuO{sub 2} content and moderation [H/(Pu+U)atomic] ratio (MR), two different homogeneous (Pu-U) O{sub 2}-polystyrene mixtures were considered: Mixture (1) 14.62 wt% PuO{sub 2} with 30.6 MR, and Mixture (2) 30.3 wt% PuO{sub 2} with 2.8 MR. In all mixtures, the uraniummore » was depleted to about O.151 wt% U{sup 235}. Assemblies contained copper, copper-cadmium or aluminum neutron poison plates having thicknesses up to {approximately}2.5 cm. This evaluation contains 22 experiments for Mixture 1, and 10 for Mixture 2 compacts. For Mixture 1, there are 10 configurations with copper plates, 6 with aluminum, and 5 with copper-cadmium. One experiment contained no poison plate. For Mixture 2 compacts, there are 3 configurations with copper, 3 with aluminum, and 3 with copper-cadmium poison plates. One experiment contained no poison plate.« less

Stable selones in glutathione-peroxidase-like catalytic cycle of selenonicotinamide derivative.

PubMed

Prabhu, Parashiva; Singh, Beena G; Noguchi, Masato; Phadnis, Prasad P; Jain, Vimal K; Iwaoka, Michio; Priyadarsini, K Indira

2014-04-21

Selenonicotinamide, 2,2'-diselenobis[3-amidopyridine] (NictSeSeNict) exhibits glutathione-peroxidase (GPx)-like activity, catalyzing the reduction of hydrogen peroxide (H2O2) by glutathione (GSH). Estimated reactivity parameters for the reaction of selenium species, according to the Dalziel kinetic model, towards GSH (ϕGSH) and H2O2 (ϕH2O2), indicated that the rate constant for the reaction of NictSeSeNict with GSH is higher as compared to that with H2O2, indicating that the activity is initiated by reduction. (77)Se NMR spectroscopy, HPLC analysis, mass spectrometry (MS) and absorption spectroscopy were employed to understand the nature of selenium intermediates responsible for the activity. The (77)Se NMR resonance at 525 ppm due to NictSeSeNict disappeared in the presence of GSH with the initial appearance of signals at δ 364 and 600 ppm, assigned to selone (NictC=Se) and selenenyl sulfide (NictSeSG), respectively. Reaction of H2O2 with NictSeSeNict produced a mixture of selenenic acid (NictSeOH) and seleninic acid (NictSeO2H) with (77)Se NMR resonances appearing at 1069 and 1165 ppm, respectively. Addition of three equivalents of GSH to this mixture produced a characteristic (77)Se NMR signal of NictSeSG. HPLC analysis of the product formed by the reaction of NictSeSeNict with GSH confirmed the formation of NictC=Se absorbing at 375 nm. Stopped-flow kinetic studies with global analysis revealed a bimolecular rate constant of 4.8 ± 0.5 × 10(3) M(-1) s(-1) and 1.7 ± 0.6 × 10(2) M(-1) s(-1) for the formation of NictC=Se produced in two consecutive reactions of NictSeSeNict and NictSeSG with GSH, respectively. Similarly the rate constant for the reaction of NictC=Se with H2O2 was estimated to be 18 ± 1.8 M(-1) s(-1). These studies clearly indicated that the GPx activity of NictSeSeNict is initiated by reduction to form NictSeSG and a stable selone, which is responsible for its efficient GPx activity.

Preparation and Properties of (YCa)(TiMn)O3−δ Ceramics Interconnect of Solid Oxide Fuel Cells

PubMed Central

Liou, Yi-Cheng; Tsai, Wen-Chou; Yen, Hao-Hsuan; Chang, Yung-Chia

2015-01-01

(YCa)(TiMn)O3–δ ceramics prepared using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. Y2Ti2O7 instead of YTiO3 formed when a mixture of Y2O3 and TiO2 with Y/Ti ratio 1/1 were sintered in air. Y2Ti2O7, YTiO2.085 and some unknown phases were detected in Y0.6Ca0.4Ti0.6Mn0.4O3–δ. Monophasic Y0.6Ca0.4Ti0.4Mn0.6O3–δ ceramics were obtained after 1400–1500 °C sintering. Dense Y0.6Ca0.4Ti0.4Mn0.6O3–δ with a density 4.69 g/cm3 was observed after 1500 °C/4 h sintering. Log σ for Y0.6Ca0.4Ti0.6Mn0.4O3–δ increased from –3.73 Scm–1 at 350 °C to –2.14 Scm–1 at 700 °C. Log σ for Y0.6Ca0.4Ti0.4Mn0.6O3–δ increased from –2.1 Scm–1 at 350 °C to –1.36 Scm–1 at 700 °C. Increasing Mn content decreased activation energy Ea and increased electrical conductivity. Reaction-sintering process is proved to be a simple and effective method to obtain (YCa)(TiMn)O3–δ ceramics for interconnects in solid oxide fuel cells. PMID:28793436

Palladium complexes of a phosphorus ylide with two stabilizing groups: synthesis, structure, and DFT study of the bonding modes.

PubMed

Falvello, Larry R; Ginés, Juan Carlos; Carbó, Jorge J; Lledós, Agustí; Navarro, Rafael; Soler, Tatiana; Urriolabeitia, Esteban P

2006-08-21

The phosphorus ylide ligand [Ph3P=C(CO2Me)C(=NPh)CO2Me] (L1) has been prepared and fully characterized by spectroscopic, crystallographic, and density functional theory (DFT) methods (B3LYP level). The reactivity of L1 toward several cationic Pd(II) and Pt(II) precursors, with two vacant coordination sites, has been studied. The reaction of [M(C/\\X)(THF)2]ClO4 with L1 (1:1 molar ratio) gives [M(C/\\X)(L1)]ClO4 [M = Pd, C/\\X = C6H4CH2NMe2 (1), S-C6H4C(H)MeNMe2 (2), CH2-8-C9H6N (3), C6H4-2-NC5H4 (4), o-CH2C6H4P(o-tol)2 (6), eta3-C3H5 (7); M = Pt, C/\\X = o-CH2C6H4P(o-tol)2 (5); M(C/\\X) = Pd(C6F5)(SC4H8) (8), PdCl2 (9)]. In complexes 1-9, the ligand L1 bonds systematically to the metal center through the iminic N and the carbonyl O of the stabilizing CO2Me group, as is evident from the NMR data and from the X-ray structure of 3. Ligand L1 can also be orthopalladated by reaction with Pd(OAc)2 and LiCl, giving the dinuclear derivative [Pd(mu-Cl)(C6H4-2-PPh2=C(CO2Me)C(CO2Me)=NPh)]2 (10). The X-ray crystal structure of 10 is also reported. In none of the prepared complexes 1-10 was the C(alpha) atom found to be bonded to the metal center. DFT calculations and Bader analysis were performed on ylide L1 and complex 9 and its congeners in order to assess the preference of the six-membered N,O metallacycle over the four-membered C,N and five-membered C,O rings. The presence of two stabilizing groups at the ylidic C causes a reduction of its bonding capabilities. The increasing strength of the Pd-C, Pd-O, and Pd-N bonds along with other subtle effects are responsible for the relative stabilities of the different bonding modes.

Interfaces in Composites. Volume 170. Materials Research Society Symposium Proceedings Held in Boston, Massachusetts on 27-29 November 1989

DTIC Science & Technology

1990-11-21

buckled coatings is obtained: G - H(ao-6 c )(do 0/dc-do c/dc)%-( o -0C) 2 (dz/dc)](l-a)h/2c (4) where % is c 2b 2(l+v)+c4 (-v)]/ E (c 2-b 2). To determine...pressure on the fiber, o , that results from a cooling differential of AT Is (9): I 20 q. = [ E 2 .(% - a5 ,) + Er(a - atr)]*AT (9) where a% is the...calculated by rule-of-mixtures, these fracture energies can be expressed in terms of critical stress intensity factors: Go + AGb ( o +AKb) 2 / E (3

Brain Cooling With Ventilation of Cold Air Over Respiratory Tract in Newborn Piglets: An Experimental and Numerical Study

PubMed Central

Bakhsheshi, Mohammad Fazel; Moradi, Hadi Vafadar; Stewart, Errol E.; Keenliside, Lynn; Lee, Ting-Yim

2015-01-01

We investigate thermal effects of pulmonary cooling which was induced by cold air through an endotracheal tube via a ventilator on newborn piglets. A mathematical model was initially employed to compare the thermal impact of two different gas mixtures, O2-medical air (1:2) and O2-Xe (1:2), across the respiratory tract and within the brain. Following mathematical simulations, we examined the theoretical predictions with O2-medical air condition on nine anesthetized piglets which were randomized to two treatment groups: 1) control group (\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{upgreek} \\usepackage{mathrsfs} \\setlength{\\oddsidemargin}{-69pt} \\begin{document} }{}$n = 4$ \\end{document}) and 2) pulmonary cooling group (\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{upgreek} \\usepackage{mathrsfs} \\setlength{\\oddsidemargin}{-69pt} \\begin{document} }{}$n = 5$ \\end{document}). Numerical and experimental results using O2-medical air mixture show that brain temperature fell from 38.5 °C and 38.3 °C ± 0.3 °C to 35.7 °C ± 0.9 °C and 36.5 °C ± 0.6 °C during 3 h cooling which corresponded to a mean cooling rate of 0.9 °C/h ± 0.2 °C/h and 0.6 °C/h ± 0.1 °C/h, respectively. According to the numerical results, decreasing the metabolic rate and increasing air velocity are helpful to maximize the cooling effect. We demonstrated that pulmonary cooling by cooling of inhalation gases immediately before they enter the trachea can slowly reduce brain and core body temperature of newborn piglets. Numerical simulations show no significant differences between two different inhaled conditions, i.e., O2-medical air (1:2) and O2-Xe (1:2) with respect to cooling rate. PMID:27170888

Purine 3':5'-cyclic nucleotides with the nucleobase in a syn orientation: cAMP, cGMP and cIMP.

PubMed

Řlepokura, Katarzyna Anna

2016-06-01

Purine 3':5'-cyclic nucleotides are very well known for their role as the secondary messengers in hormone action and cellular signal transduction. Nonetheless, their solid-state conformational details still require investigation. Five crystals containing purine 3':5'-cyclic nucleotides have been obtained and structurally characterized, namely adenosine 3':5'-cyclic phosphate dihydrate, C10H12N5O6P·2H2O or cAMP·2H2O, (I), adenosine 3':5'-cyclic phosphate 0.3-hydrate, C10H12N5O6P·0.3H2O or cAMP·0.3H2O, (II), guanosine 3':5'-cyclic phosphate pentahydrate, C10H12N5O7P·5H2O or cGMP·5H2O, (III), sodium guanosine 3':5'-cyclic phosphate tetrahydrate, Na(+)·C10H11N5O7P(-)·4H2O or Na(cGMP)·4H2O, (IV), and sodium inosine 3':5'-cyclic phosphate tetrahydrate, Na(+)·C10H10N4O7P(-)·4H2O or Na(cIMP)·4H2O, (V). Most of the cyclic nucleotide zwitterions/anions [two from four cAMP present in total in (I) and (II), cGMP in (III), cGMP(-) in (IV) and cIMP(-) in (V)] are syn conformers about the N-glycosidic bond, and this nucleobase arrangement is accompanied by Crib-H...Npur hydrogen bonds (rib = ribose and pur = purine). The base orientation is tuned by the ribose pucker. An analysis of data obtained from the Cambridge Structural Database made in the context of syn-anti conformational preferences has revealed that among the syn conformers of various purine nucleotides, cyclic nucleotides and dinucleotides predominate significantly. The interactions stabilizing the syn conformation have been indicated. The inter-nucleotide contacts in (I)-(V) have been systematized in terms of the chemical groups involved. All five structures display three-dimensional hydrogen-bonded networks.

Simulation of toluene decomposition in a pulse-periodic discharge operating in a mixture of molecular nitrogen and oxygen

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trushkin, A. N.; Kochetov, I. V.

The kinetic model of toluene decomposition in nonequilibrium low-temperature plasma generated by a pulse-periodic discharge operating in a mixture of nitrogen and oxygen is developed. The results of numerical simulation of plasma-chemical conversion of toluene are presented; the main processes responsible for C{sub 6}H{sub 5}CH{sub 3} decomposition are identified; the contribution of each process to total removal of toluene is determined; and the intermediate and final products of C{sub 6}H{sub 5}CH{sub 3} decomposition are identified. It was shown that toluene in pure nitrogen is mostly decomposed in its reactions with metastable N{sub 2}(A{sub 3}{Sigma}{sub u}{sup +}) and N{sub 2}(a Primemore » {sup 1}{Sigma}{sub u}{sup -}) molecules. In the presence of oxygen, in the N{sub 2} : O{sub 2} gas mixture, the largest contribution to C{sub 6}H{sub 5}CH{sub 3} removal is made by the hydroxyl radical OH which is generated in this mixture exclusively due to plasma-chemical reactions between toluene and oxygen decomposition products. Numerical simulation showed the existence of an optimum oxygen concentration in the mixture, at which toluene removal is maximum at a fixed energy deposition.« less

Sterilization of Bacillus pumilus spores using supercritical fluid carbon dioxide containing various modifier solutions.

PubMed

Shieh, Edison; Paszczynski, Andrzej; Wai, Chien M; Lang, Qingyong; Crawford, Ronald L

2009-03-01

Supercritical fluid carbon dioxide (SF-CO(2)) with small amounts of chemical modifier(s) provides a very effective sterilization technique that should be useful for destroying microorganism on heat-sensitive devices such as instruments flown on planetary-bound spacecraft. Under a moderate temperature (50 degrees C) and pressure (100 atm), spores of Bacillus pumilus strains ATCC 7061 and SAFR 032 can be effectively inactivated/eliminated from metal surfaces and small electronic devices in only 45 min using optimized modifier concentrations. Modifiers explored in this study included hydrogen peroxide (H(2)O(2)), tert-butyl hydroperoxide, formic acid, and Triton X-100. During sterilization procedure the modifiers were continuously added to SF-CO(2) in either methanol or water at controlled concentrations. The lowest effective concentrations were established for each modifier. Complete elimination of both types of B. pumilus endospores occurred with an optimal modifier addition of either or 10% methanol containing 12% H(2)O(2) or 12% tert-butyl hydroperoxide in SF-CO(2), or a mixture of 6% H(2)O(2) and 6% tert-butyl hydroperoxide. Using water as the carrier of SF-CO(2) modifier, the complete elimination of spores viability of both B. pumilus strains occurred with an addition of either 3.3% water containing 3% H(2)O(2), or 3.3% water containing 10% methanol and 0.5% formic acid, or 3.3% water containing 10% methanol, 1% formic acid and 2% H(2)O(2).

Hydrogen-alkali exchange between silicate melts and two-phase aqueous mixtures: an experimental investigation

NASA Astrophysics Data System (ADS)

Williams, Thomas J.; Candela, Philip A.; Piccoli, Philip M.

Experiments were performed in the three-phase system high-silica rhyolite melt + low-salinity aqueous vapor + hydrosaline brine, to investigate the exchange equilibria for hydrogen, potassium, and sodium in magmatic-hydrothermal systems at 800 °C and 100 MPa, and 850 °C and 50 MPa. The Kaqm/meltH,Na and Kaqm/meltH,K for hydrogen-sodium exchange between a vapor + brine mixture and a silicate melt are inversely proportional to the total chloride concentration (ΣCl) in the vapor + brine mixture indicating that HCl/NaCl and HCl/KCl are higher in the low-salinity aqueous vapor relative to high-salinity brine. The equilibrium constants for vapor/melt and brine/melt exchange were extracted from regressions of Kaqm/meltH,Na and Kaqm/meltH,K versus the proportion of aqueous vapor relative to brine in the aqueous mixture (Faqv) at P and T, expressed as a function of ΣCl. No significant pressure effect on the empirically determined exchange constants was observed for the range of pressures investigated. Model equilibrium constants are: Kaqv/meltH,Na(vapor/melt)=26(+/-1.3) at 100 MPa (800 °C), and 19( +/- 7.0) at 50 MPa (850 °C) Kaqv/meltH,K=14(+/-1.1) at 100 MPa (800 °C), and 24(+/-12) at 50 MPa (850 °C) Kaqb/meltH,b(brine/melt)= 1.6(+/-0.7) at 100 MPa (800 °C), and 3.9(+/-2.3) at 50 MPa (850 °C) and Kaqb/meltH,K=2.7(+/-1.2) at 100 MPa (800 °C) and 3.8(+/-2.3) at 50 MPa (850 °C). Values for Kaqv/meltH,K and Kaqb/meltH,K were used to calculate KCl/HCl in the aqueous vapor and brine as a function of melt aluminum saturation index (ASI: molar Al2O3/(K2O+Na2O+CaO) and pressure. The model log KCl/HCl values show that a change in melt ASI from peraluminous (ASI = 1.04) to moderately metaluminous (ASI = 1.01) shifts the cooling pathway (in temperature-log KCl/HCl space) of the aqueous vapor toward the andalusite+muscovite+K-feldspar reaction point.

Technique for measuring gas conversion factors

NASA Technical Reports Server (NTRS)

Singh, J. J.; Sprinkle, D. R. (Inventor)

1985-01-01

A method for determining hydrocarbon conversion factors for a flowmeter. A mixture of air, O2 and C sub x H sub y is burned and the partial paressure of O2 in the resulting gas is forced to equal the partial pressure of O2 in air. The flowrate of O2 flowing into the mixture is measured by flowmeter and the flowrate of C sub x H sub y flowing into the mixture is measured by the flowmeter conversion factor is to be determined. These measured values are used to calculate the conversion factor.

Alkaline peroxide pretreatment of corn stover: effects of biomass, peroxide, and enzyme loading and composition on yields of glucose and xylose

PubMed Central

2011-01-01

Background Pretreatment is a critical step in the conversion of lignocellulose to fermentable sugars. Although many pretreatment processes are currently under investigation, none of them are entirely satisfactory in regard to effectiveness, cost, or environmental impact. The use of hydrogen peroxide at pH 11.5 (alkaline hydrogen peroxide (AHP)) was shown by Gould and coworkers to be an effective pretreatment of grass stovers and other plant materials in the context of animal nutrition and ethanol production. Our earlier experiments indicated that AHP performed well when compared against two other alkaline pretreatments. Here, we explored several key parameters to test the potential of AHP for further improvement relevant to lignocellulosic ethanol production. Results The effects of biomass loading, hydrogen peroxide loading, residence time, and pH control were tested in combination with subsequent digestion with a commercial enzyme preparation, optimized mixtures of four commercial enzymes, or optimized synthetic mixtures of pure enzymes. AHP pretreatment was performed at room temperature (23°C) and atmospheric pressure, and after AHP pretreatment the biomass was neutralized with HCl but not washed before enzyme digestion. Standard enzyme digestion conditions were 0.2% glucan loading, 15 mg protein/g glucan, and 48 h digestion at 50°C. Higher pretreatment biomass loadings (10% to 20%) gave higher monomeric glucose (Glc) and xylose (Xyl) yields than the 2% loading used in earlier studies. An H2O2 loading of 0.25 g/g biomass was almost as effective as 0.5 g/g, but 0.125 g/g was significantly less effective. Optimized mixtures of four commercial enzymes substantially increased post-AHP-pretreatment enzymatic hydrolysis yields at all H2O2 concentrations compared to any single commercial enzyme. At a pretreatment biomass loading of 10% and an H2O2 loading of 0.5 g/g biomass, an optimized commercial mixture at total protein loadings of 8 or 15 mg/g glucan gave monomeric Glc yields of 83% or 95%, respectively. Yields of Glc and Xyl after pretreatment at a low hydrogen peroxide loading (0.125 g H2O2/g biomass) could be improved by extending the pretreatment residence time to 48 h and readjusting the pH to 11.5 every 6 h during the pretreatment. A Glc yield of 77% was obtained using a pretreatment of 15% biomass loading, 0.125 g H2O2/g biomass, and 48 h with pH adjustment, followed by digestion with an optimized commercial enzyme mixture at an enzyme loading of 15 mg protein/g glucan. Conclusions Alkaline peroxide is an effective pretreatment for corn stover. Particular advantages are the use of reagents with low environmental impact and avoidance of special reaction chambers. Reasonable yields of monomeric Glc can be obtained at an H2O2 concentration one-quarter of that used in previous AHP research. Additional improvements in the AHP process, such as peroxide stabilization, peroxide recycling, and improved pH control, could lead to further improvements in AHP pretreatment. PMID:21658263

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thangavelu, Sonia G.; Butcher, Ray J.; Cahill, Christopher L.

Thiophene 2,5-dicarboxylic acid (TDC) was reacted with uranyl acetate dihydrate and one (or none) of six N-donor chelating ligands (2,2'-bipyridine (BPY), 4,4'-dimethyl-2,2'-bipyridine (4-MeBPY), 5,5'-dimethyl-2,2'-bipyridine (5-MeBPY), 6,6'-dimethyl-2,2'-bipyridine (6-MeBPY), 4,4',6,6'-tetramethyl-2,2'-bipyridine (4,6-MeBPY), and tetrakis(2-pyridyl)pyrazine (TPPZ) to result in the crystallization of seven uranyl coordination polymers, which were characterized by their crystal structures and luminescence properties. The seven coordination polymers, Na2[(UO2)2(C6H2O4S)3]·4H2O (1), [(UO2)4(C6H2O4S)5(C10H8N2)2]·C10H10N2·3H2O (2), [(UO2)(C6H2O4S)(C12H12N3)] (3), [(UO2)(C6H2O4S)(C12H12N3)]·H2O (4), [(UO2)2(C6H2O4S)3]·(C12H14N2)·5H2O (5), [(UO2)3(CH3CO2)(C6H2O4S)4](C14H17N2)3·(C14H16N2)·H2O (6), and [(UO2)2(C6H2O4S)3](C24H18N6) (7), consist of either uranyl hexagonal bipyramidal or pentagonal bipyramidal coordination geometries. In all structures, structural variations in the local and global structures of 1–7 are influenced by the positionsmore » (or number) of methyl groups or pyridyl rings on the N-donor species, thus resulting in a wide diversity of structures ranging from single chains, double chains, or 2-D sheets. Direct coordination of N-donor ligands to uranyl centers is observed in the chain structures of 2–4 using BPY, 4-MeBPY, and 5-MeBPY, whereas the N-donor species participate as guests (as either neutral or charge balancing species) in the chain and sheet structures of 5–7 using 6-MeBPY, 4,6-MeBPY, and TPPZ, respectively. Compound 1 is the only structure that does not contain any N-donor ligands and thus crystallizes as a 2-D interpenetrating sheet. The luminescent properties of 1–7 are influenced by the direct coordination or noncoordination of N-donor species to uranyl centers. Compounds 2–4 exhibit typical UO22+ emission upon direct coordination of N-donors, but its absence is observed in 1, 5, 6, and 7, when N-donor species participate as guest molecules. These results suggest that direct coordination of N-donor ligands participate as chromophores, thus resulting in possible UO22+ sensitization. The lack of emission in 1, 5, 6, and 7 may be explained by the extended conjugation of the TDC ligands within their structures.« less

Structural characterization of selenium and selenium-diiodine analogues of the antithyroid drug 6-n-propyl-2-thiouracil and its alkyl derivatives.

PubMed

Antoniadis, Constantinos D; Blake, Alexander J; Hadjikakou, Sotiris K; Hadjiliadis, Nick; Hubberstey, Peter; Schröder, Martin; Wilson, Claire

2006-08-01

The structures of four selenium analogues of the antithyroid drug 6-n-propyl-2-thiouracil [systematic name: 2,3-dihydro-6-n-propyl-2-thioxopyrimidin-4(1H)-one], namely 6-methyl-2-selenouracil, C(5)H(6)N(2)OSe (1), 6-ethyl-2-selenouracil, C(6)H(8)N(2)OSe (2), 6-n-propyl-2-selenouracil, C(7)H(10)N(2)OSe (3), and 6-isopropyl-2-selenouracil, C(7)H(10)N(2)OSe (4), are described, along with that of the dichloromethane monosolvate of 6-isopropyl-2-selenouracil, C(7)H(10)N(2)OSe.CH(2)Cl(2) (4.CH(2)Cl(2)). The extended structure of (1) is a two-dimensional sheet of topology 6(3) with a brick-wall architecture. The extended structures of (2) and (4) are analogous, being based on a chain of eight-membered R(8)(6)(32) hydrogen-bonded rings. In (3) and (4.CH(2)Cl(2)), R(2)(2)(8) hydrogen bonding links molecules into chains. 6-n-Propyl-2-selenouracil.I(2), C(7)H(10)N(2)OSe.I(2) (7), is a charge-transfer complex with a ;spoke' structure, the extended structure of which is based on a linear chain formed principally by intermolecular N-H...O hydrogen bonds. Re-crystallization of 6-ethyl-2-selenouracil or (7) from acetone gave crystals of the diselenides [N-(6'-ethyl-4'-pyrimidone)(6-ethyl-2-selenouracil)(2)(Se-Se)].2H(2)O (9.2H(2)O) or [N-(6'-n-propyl-4'-pyrimidone)(6-n-propyl-2-selenouracil)(2)(Se-Se)] (10), respectively: these have similar extended chain structures formed via N-H...O and C-H...O hydrogen bonds, stacked to give two-dimensional sheets. Re-crystallization of (7) from methanol/acetonitrile led via deselenation to the formation of crystals of 6-n-propyl-2-uracil (11), in which six symmetry-related molecules combine to form a six-membered R(6)(6)(24) hydrogen-bonded ring, with each pair of molecules linked by an R(2)(2)(8) motif.

Species and temperature measurements of methane oxidation in a nanosecond repetitively pulsed discharge

PubMed Central

Lefkowitz, Joseph K; Guo, Peng; Rousso, Aric; Ju, Yiguang

2015-01-01

Speciation and temperature measurements of methane oxidation during a nanosecond repetitively pulsed discharge in a low-temperature flow reactor have been performed. Measurements of temperature and formaldehyde during a burst of pulses were made on a time-dependent basis using tunable diode laser absorption spectroscopy, and measurements of all other major stable species were made downstream of a continuously pulsed discharge using gas chromatography. The major species for a stoichiometric methane/oxygen/helium mixture with 75% dilution are H2O, CO, CO2, H2, CH2O, CH3OH, C2H6, C2H4 and C2H2. A modelling tool to simulate homogeneous plasma combustion kinetics is assembled by combining the ZDPlasKin and CHEMKIN codes. In addition, a kinetic model for plasma-assisted combustion (HP-Mech/plasma) of methane, oxygen and helium mixtures has been assembled to simulate the measurements. Predictions can accurately capture reactant consumption as well as production of the major product species. However, significant disagreement is found for minor species, particularly CH2O and CH3OH. Further analysis revealed that the plasma-activated low-temperature oxidation pathways, particularly those involving CH3O2 radical reactions and methane reactions with O(1D), are responsible for this disagreement. PMID:26170433

Combustion characteristics of nanoaluminum, liquid water, and hydrogen peroxide mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabourin, J.L.; Yetter, R.A.; Risha, G.A.

2008-08-15

An experimental investigation of the combustion characteristics of nanoaluminum (nAl), liquid water (H{sub 2}O{sub (l)}), and hydrogen peroxide (H{sub 2}O{sub 2}) mixtures has been conducted. Linear and mass-burning rates as functions of pressure, equivalence ratio ({phi}), and concentration of H{sub 2}O{sub 2} in H{sub 2}O{sub (l)} oxidizing solution are reported. Steady-state burning rates were obtained at room temperature using a windowed pressure vessel over an initial pressure range of 0.24 to 12.4 MPa in argon, using average nAl particle diameters of 38 nm, {phi} from 0.5 to 1.3, and H{sub 2}O{sub 2} concentrations between 0 and 32% by mass. Atmore » a nominal pressure of 3.65 MPa, under stoichiometric conditions, mass-burning rates per unit area ranged between 6.93 g/cm{sup 2} s (0% H{sub 2}O{sub 2}) and 37.04 g/cm{sup 2} s (32% H{sub 2}O{sub 2}), which corresponded to linear burning rates of 9.58 and 58.2 cm/s, respectively. Burning rate pressure exponents of 0.44 and 0.38 were found for stoichiometric mixtures at room temperature containing 10 and 25% H{sub 2}O{sub 2}, respectively, up to 5 MPa. Burning rates are reduced above {proportional_to}5 MPa due to the pressurization of interstitial spaces of the packed reactant mixture with argon gas, diluting the fuel and oxidizer mixture. Mass burning rates were not measured above {proportional_to}32% H{sub 2}O{sub 2} due to an anomalous burning phenomena, which caused overpressurization within the quartz sample holder, leading to tube rupture. High-speed imaging displayed fingering or jetting ahead of the normal flame front. Localized pressure measurements were taken along the sample length, determining that the combustion process proceeded as a normal deflagration prior to tube rupture, without significant pressure buildup within the tube. In addition to burning rates, chemical efficiencies of the combustion reaction were determined to be within approximately 10% of the theoretical maximum under all conditions studied. (author)« less

Experimental ion mobility measurements in Xe-C2H6

NASA Astrophysics Data System (ADS)

Perdigoto, J. M. C.; Cortez, A. F. V.; Veenhof, R.; Neves, P. N. B.; Santos, F. P.; Borges, F. I. G. M.; Conde, C. A. N.

2017-10-01

In this paper we present the results of the ion mobility measurements made in gaseous mixtures of xenon (Xe) with ethane (C2H6) for pressures ranging from 6 to 10 Torr (8-10.6 mbar) and for low reduced electric fields in the 10 Td to 25 Td range (2.4-6.1 kVṡcm-1ṡ bar-1), at room temperature. The time of arrival spectra revealed two peaks throughout the entire range studied which were attributed to ion species with 3-carbons (C3H5+, C3H6+ C3H8+ and C3H9+) and with 4-carbons (C4H7+, C4H9+ and C4H10+). Besides these, and for Xe concentrations above 70%, a bump starts to appear at the right side of the main peak for reduced electric fields higher than 20 Td, which was attributed to the resonant charge transfer of C2H6+ to C2H6 that affects the mobility of its ion products (C3H8+ and C3H9+). The time of arrival spectra for Xe concentrations of 20%, 50%, 70% and 90% are presented, together with the reduced mobilities as a function of the Xe concentration calculated from the peaks observed for the low reduced electric fields and pressures studied.

Relatedness of the O-polysaccharide structures of Escherichia coli O123 and Salmonella enterica O58, both containing 4,6-dideoxy-4-{N-[(S)-3-hydroxybutanoyl]-D-alanyl}amino-D-glucose; revision of the E. coli O123 O-polysaccharide structure.

PubMed

Perepelov, Andrei V; Liu, Bin; Shevelev, Sergei D; Senchenkova, Sof'ya N; Shashkov, Alexander S; Feng, Lu; Knirel, Yuriy A; Wang, Lei

2010-04-19

O-Polysaccharides were isolated by mild acid degradation of the lipopolysaccharides of Escherichia coli O123 and Salmonella enterica O58 and studied by chemical methods and 2D (1)H and (13)C NMR spectroscopy, including experiments in a H(2)O/D(2)O mixture, which enabled observation of correlations for nitrogen-linked protons. The following structure of the O-polysaccharide of E. coli O123 was established: -->3)-beta-D-Quip4NAlaHb-(1-->6)-alpha-D-GlcpNAc-(1-->3)-alpha-L-QuipNAc-(1-->3)-alpha-D-Glcp (6)(approx. 30% OAc)NAc-(1--> where L-QuipNAc stands for 2-acetamido-2,6-dideoxy-L-glucose and D-Qui4NAlaHb for 4-{N-[(S)-3-hydroxybutanoyl]-D-alanyl}amino-4,6-dideoxy-D-glucose. The latter was isolated as an ethylene glycol glycoside by three sequential Smith degradations of the O-deacetylated O-polysaccharide. The structure established in this work is at variance with the E. coli O123-polysaccharide structure reported earlier [Clark, C. G.; Kropinski, A. M.; Parolis, H.; Grant, C. C.; Trout-Yakel, K. M.; Franklin, K.; Ng, L. K.; Paramonov, N. A.; Parolis, L. A.; Rahn, K.; Tabor, H. J. Med. Microbiol.2009, 58, 884-894]. In accordance with the genetic data, the O-polysaccharide of S. enterica O58 has the same structure, except for it lacks the O-acetylation. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

X-ray fluorescence analysis of Cr(6+) component in mixtures of Cr(2)O(3) and K(2)CrO(4).

PubMed

Tochio, Tatsunori; Sakakura, Shusuke; Oohashi, Hirofumi; Mizota, Hirohisa; Zou, Yanhui; Ito, Yoshiaki; Fukushima, Sei; Tanuma, Shigeo; Shoji, Takashi; Fujimura, Hajime; Yamashita, Michiru

2010-01-01

X-ray fluorescence analysis using Cr K(alpha) spectra was applied to the determination of the mixing ratio of Cr(6+) to (Cr(6+) + Cr(3+)) in several mixtures of K(2)CrO(4) and Cr(2)O(3). Because the powder of K(2)CrO(4) contained large particles that were more than 50 microm in diameter, it was ground between a pestle and a mortar for about 8 h. The coarse particles still remaining were removed by using a sieve with 325-mesh (44 microm) in order to reduce the difference in absorption effects between emissions from Cr(6+) and those from Cr(3+). The mixing ratio, K(2)CrO(4)/(K(2)CrO(4) + Cr(2)O(3)), of the five mixtures investigated is 0.50, 0.40, 0.20, 0.10, and 0.05 in weight, respectively. Each spectrum obtained was analyzed by decomposing it into two reference spectra, those of the two pure materials, K(2)CrO(4) and Cr(2)O(3), with a constant background. The results for the mixtures containing K(2)CrO(4) of more than 20 wt% are that the relative deviation from the true value is less than approximately 5%. On the other hand, when the content of K(2)CrO(4) decreases to less than 10 wt%, the relative deviation gets so large as 20 - 25%. The error coming from a peak separation of spectrum involved in our results were estimated by applying our method to five sets of data for each mixture computationally generated, taking into account the uncertainty in total counts of real measurements.

Laboratory Experiments on the Reactions of PAH Cations with Molecules and Atoms of Interstellar Interest

NASA Technical Reports Server (NTRS)

LePage, V.; Lee, H. S.; Bierbaum, V. M.; Snow, T. P.

1996-01-01

The C10H8(+) cation and its dehydrogenated derivatives, C10H7(+) and C10H6(+), have been studied using a selected ion flow tube (SIFT). Reactions with molecules and atoms of interstellar interest show that C10H8(+) reacts with N md O to give neutral products HCN and CO, respectively. C10H6(+) and C10H6(+) are moderately reactive and reactions proceed through association with molecules. The implications of these results for the depletion of C10H(n)(+) in the interstellar medium are briefly discussed.

Shear rheology and in-vitro release kinetic study of apigenin from lyotropic liquid crystal.

PubMed

Fan, Jun; Liu, Feng; Wang, Zhongni

2016-01-30

Apigenin is a flavonoid compound with diverse pharmacological functions which could develop health benefit products, but its formulation is hampered by its poor water solubility and bioavailability. In this paper, in order to overcome these difficulties, apigenin was encapsulated in LLC formed by polyoxyethylene-10-oleyl ether (Brij 97) and sodium deoxycholate (NaDC) mixtures. The hexagonal liquid crystalline phase (H) and the cubic liquid crystalline phase (C) were found in this system. The shear rheology was used to study the structure change with temperature. It was shown that C3 (Brij 97-NaDC/IPM-PEG400/H2O=36:9:55) was C at low temperature. But above 35.6°C, the matrix of C3 completely transformed to polymer solution. The matrix of H3 was H (Brij 97-NaDC:IPM-PEG 400:H2O=50:9:41) below 50°C, but the structural strength change was obvious. Vitro release experiment was used to study drug release kinetics. It was indicated that apigenin encapsulated in LLC conformed to the concentration diffusion model, and cumulative percentage of apigenin released from C3 and H3 had corresponding relationship with the shear rheology at different temperatures. Copyright © 2015. Published by Elsevier B.V.

Effects of water immersion to the neck on pulmonary circulation and tissue volume in man

NASA Technical Reports Server (NTRS)

Begin, R.; Epstein, M.; Sackner, M. A.; Levinson, R.; Dougherty, R.; Duncan, D.

1976-01-01

A rapid noninvasive breathing method is used to obtain serial measurements of the pulmonary capillary blood flow, diffusing capacity per unit of alveolar volume, combined pulmonary tissue plus capillary volume, functional residual capacity, and oxygen consumption in five normal subjects undergoing 6 h of sitting, 4 h of sitting while immersed to the neck in thermoneutral water, and 4 h of lying in thermoneutral water to the neck. The rebreathing method employed a test gas mixture containing 0.5% C2H2, 0.3% C(18)O, 10% He, 21% O2, and balance N2. It is shown that immersion to the neck in the seated posture results in significant increases in sodium excretion cardiac output, and diffusing capacity per unit of alveolar volume. The pulmonary tissue plus capillary volume did not change, demonstrating that the central vascular engorgement induced by water immersion is not accompanied by significant extravasation of fluid into the pulmonary interstitial space.

A Twist on Facial Selectivity of Hydride Reductions of Cyclic Ketones: Twist-Boat Conformers in Cyclohexanone, Piperidone, and Tropinone Reactions

PubMed Central

2015-01-01

The role of twist-boat conformers of cyclohexanones in hydride reductions was explored. The hydride reductions of a cis-2,6-disubstituted N-acylpiperidone, an N-acyltropinone, and tert-butylcyclohexanone by lithium aluminum hydride and by a bulky borohydride reagent were investigated computationally and compared to experiment. Our results indicate that in certain cases, factors such as substrate conformation, nucleophile bulkiness, and remote steric features can affect stereoselectivity in ways that are difficult to predict by the general Felkin–Anh model. In particular, we have calculated that a twist-boat conformation is relevant to the reactivity and facial selectivity of hydride reduction of cis-2,6-disubstituted N-acylpiperidones with a small hydride reagent (LiAlH4) but not with a bulky hydride (lithium triisopropylborohydride). PMID:25372509

Double salt crystal structure of hexa-sodium hemiundeca-hydrogen α-hexa-molybdoplatinate(IV) heminona-hydrogen α-hexa-molybdoplatinate(IV) nona-cosa-hydrate: di-hydrogen disordered-mixture double salt.

PubMed

Joo, Hea-Chung; Park, Ki-Min; Lee, Uk

2015-10-01

The title double salt containing two distinct, differently protonated hexa-molybdoplatinate(IV) polyanions, Na6[H5.5 α-PtMo6O24][H4.5 α-PtMo6O24]·29H2O, has been synthesized by a hydro-thermal reaction at ca pH 1.80. The positions of the H atoms in the polyanions were established from difference Fourier maps and confirmed by the inter-polyanion hydrogen bonds, bond-distance elongation, and bond-valence sum (BVS) calculations. The fractional numbers of H atoms in each polyanion are required for charge balance and in order to avoid unrealistically short H⋯H distances in the inter-polyanion hydrogen bonds. Considering the disorder, the refined formula of the title polyanion, {[H5.5 α-PtMo6O24]; polyanion (A) and [H4.5 α-PtMo6O24]; polyanion (B)}(6-), can be rewritten as a set of real formula, viz. {[H6 α-PtMo6O24]; polyanion (A). [H4 α-PtMo6O24]; polyanion (B)}(6-) and {[H5 α-PtMo6O24]; polyanion (A). [H5 α-PtMo6O24]; polyanion (B)}(6-). The polyanion pairs both form dimers of the same formula, viz. {[H10 α-Pt2Mo12O48]}(6-) connected by seven inter-polyanion O-H⋯O hydrogen bonds.

Iron(II) catalysis in oxidation of hydrocarbons with ozone in acetonitrile

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bataineh, Hajem; Pestovsky, Oleg; Bakac, Andreja

Oxidation of alcohols, ethers, and sulfoxides by ozone in acetonitrile is catalyzed by submillimolar concentrations of Fe(CH 3CN) 6 2+. The catalyst provides both rate acceleration and greater selectivity toward the less oxidized products. For example, Fe(CH 3CN) 6 2+-catalyzed oxidation of benzyl alcohol yields benzaldehyde almost exclusively (>95%), whereas the uncatalyzed reaction generates a 1:1 mixture of benzaldehyde and benzoic acid. Similarly, aliphatic alcohols are oxidized to aldehydes/ketones, cyclobutanol to cyclobutanone, and diethyl ether to a 1:1 mixture of ethanol and acetaldehyde. The kinetics of oxidation of alcohols and diethyl ether are first-order in [Fe(CH 3CN) 6 2+] andmore » [O 3] and independent of [substrate] at concentrations greater than ~5 mM. In this regime, the rate constant for all of the alcohols is approximately the same, k cat = (8 ± 1) × 10 4 M –1 s –1, and that for (C 2H 5) 2O is (5 ± 0.5) × 10 4 M –1 s –1. In the absence of substrate, Fe(CH 3CN) 6 2+ reacts with O 3 with k Fe = (9.3 ± 0.3) × 10 4 M –1 s –1. The similarity between the rate constants k Fe and k cat strongly argues for Fe(CH 3CN) 6 2+/O 3 reaction as rate-determining in catalytic oxidation. The active oxidant produced in Fe(CH 3CN) 6 2+/O 3 reaction is suggested to be an Fe(IV) species in analogy with a related intermediate in aqueous solutions. As a result, this assignment is supported by the similarity in kinetic isotope effects and relative reactivities of the two species toward substrates.« less

Iron(II) catalysis in oxidation of hydrocarbons with ozone in acetonitrile

DOE PAGES

Bataineh, Hajem; Pestovsky, Oleg; Bakac, Andreja

2015-02-11

Oxidation of alcohols, ethers, and sulfoxides by ozone in acetonitrile is catalyzed by submillimolar concentrations of Fe(CH 3CN) 6 2+. The catalyst provides both rate acceleration and greater selectivity toward the less oxidized products. For example, Fe(CH 3CN) 6 2+-catalyzed oxidation of benzyl alcohol yields benzaldehyde almost exclusively (>95%), whereas the uncatalyzed reaction generates a 1:1 mixture of benzaldehyde and benzoic acid. Similarly, aliphatic alcohols are oxidized to aldehydes/ketones, cyclobutanol to cyclobutanone, and diethyl ether to a 1:1 mixture of ethanol and acetaldehyde. The kinetics of oxidation of alcohols and diethyl ether are first-order in [Fe(CH 3CN) 6 2+] andmore » [O 3] and independent of [substrate] at concentrations greater than ~5 mM. In this regime, the rate constant for all of the alcohols is approximately the same, k cat = (8 ± 1) × 10 4 M –1 s –1, and that for (C 2H 5) 2O is (5 ± 0.5) × 10 4 M –1 s –1. In the absence of substrate, Fe(CH 3CN) 6 2+ reacts with O 3 with k Fe = (9.3 ± 0.3) × 10 4 M –1 s –1. The similarity between the rate constants k Fe and k cat strongly argues for Fe(CH 3CN) 6 2+/O 3 reaction as rate-determining in catalytic oxidation. The active oxidant produced in Fe(CH 3CN) 6 2+/O 3 reaction is suggested to be an Fe(IV) species in analogy with a related intermediate in aqueous solutions. As a result, this assignment is supported by the similarity in kinetic isotope effects and relative reactivities of the two species toward substrates.« less

A unified equation of state for fluids of C-H-O-N-S-Ar composition and their mixtures up to very high temperatures and pressures

NASA Astrophysics Data System (ADS)

Belonoshko, A. B.; Saxena, S. K.

1992-10-01

A unified equation of state (EOS) is derived for 13 gases (including H2O, CO2, CH4, CO, O2, H2, Ar, N2, NH3, H2S, SO2, COS, and S2) in C-H-O-N-S-Ar system, on the basis of molecular dynamical simulated PVT data, assuming these species to be alpha-exponential-6 fluids at high temperature and pressure. The EOS equation is parameterized for these gases in the ranges of temperature and pressure 400-4000 K and 5-1000 kbar, respectively. It is shown that the equation reproduces most of the available experimental data in the limits of experimental accuracy of volume measurements.

Axial zero-field splitting in mononuclear Co(ii) 2-N substituted N-confused porphyrin: Co(2-NC3H5-21-Y-CH2C6H4CH3-NCTPP)Cl (Y = o, m, p) and Co(2-NC3H5-21-CH2C6H5-NCTPP)Cl.

PubMed

Lai, Ya-Yuan; Chang, Yu-Chang; Chen, Jyh-Horung; Wang, Shin-Shin; Tung, Jo-Yu

2016-03-21

The inner C-benzyl- and C-o-xylyl (or m-xylyl, p-xylyl)-substituted cobalt(ii) complexes of a 2-N-substituted N-confused porphyrin were synthesized from the reaction of 2-NC3H5NCTPPH (1) and CoCl2·6H2O in toluene (or o-xylene, m-xylene, p-xylene). The crystal structures of diamagnetic chloro(2-aza-2-allyl-5,10,15,20-tetraphenyl-21-hydrogen-21-carbaporphyrinato-N,N',N'')zinc(ii) [Zn(2-NC3H5-21-H-NCTPP)Cl; 3 ] and paramagnetic chloro(2-aza-2-allyl-5,10,15,20-tetraphenyl-21-benzyl-21-carbaporphyrinato-N,N',N'')cobalt(ii) [Co(2-NC3H5-21-CH2C6H5NCTPP)Cl; 7], and chloro(2-aza-2-allyl-5,10,15,20-tetraphenyl-21-Y-xylyl-21-carbaporphyrinato-N,N',N'')cobalt(ii) [Co(2-NC3H5-21-Y-CH2C6H4CH3NCTPP)Cl] [Y = o (8), m (9), p (10)] were determined. The coordination sphere around the Zn(2+) (or Co(2+)) ion in 3 (or 7-10) is a distorted tetrahedron (DT). The free energy of activation at the coalescence temperature Tc for the exchange of phenyl ortho protons o-H (26) with o-H (22) in 3 in a CDCl3 solvent is found to be ΔG = 61.4 kJ mol(-1) through (1)H NMR temperature-dependent measurements. The axial zero-field splitting parameter |D| was found to vary from 35.6 cm(-1) in 7 (or 30.7 cm(-1) in 8) to 42.0 cm(-1) in 9 and 46.9 cm(-1) in 10 through paramagnetic susceptibility measurements. The magnitude of |D| can be related to the coordination sphere at the cobalt sites.

Morphologies of aerosol particles consisting of two liquid phases

NASA Astrophysics Data System (ADS)

Song, Mijung; Marcolli, Claudia; Krieger, Ulrich; Peter, Thomas

2013-04-01

Recent studies have shown that liquid-liquid phase separation (LLPS) might be a common feature in mixed organic/ammonium sulfate (AS)/H2O particles. Song et al. (2012) observed that in atmospheric relevant organic/AS/H2O mixtures LLPS always occurred for organic aerosol compositions with O:C < 0.56, depended on the specific functional groups of organics in the range of 0.56 < O:C < 0.80 and never appeared for O:C > 0.80. The composition of the organic fraction and the mixing state of aerosol particles may influence deliquescence relative humidity (DRH) and efflorescence relative humidity (ERH) of inorganic salts during RH cycles and also aerosol morphology. In order to determine how the deliquescence and efflorescence of AS in mixed organic/AS/H2O particles is influenced by LLPS and to identify the corresponding morphologies of the particles, we subjected organic/AS/H2O particles deposited on a hydrophobically coated substrate to RH cycles and observed the phase transitions using optical microscopy and Raman spectroscopy. In this study, we report results from 21 organic/AS/H2O systems with O:C ranging from 0.55 - 0.85 covering aliphatic and aromatic oxidized compounds. Eight systems did not show LLPS for all investigated organic-to-inorganic ratios, nine showed core-shell morphology when present in a two-liquid-phases state and four showed both, core-shell or partially engulfed configurations depending on the organic-to-inorganic ratio. While AS in aerosol particles with complete LLPS showed almost constant values of ERH = 44 ± 4 % and DRH = 77 ± 2 %, a strong reduction or complete inhibition of efflorescence occurred for mixtures that did not exhibit LLPS. To confirm these findings, we performed supplementary experiments on levitated particles in an electrodynamic balance and compared surface and interfacial tensions of the investigated mixtures. Reference Song, M., C. Marcolli, U. K. Krieger, A. Zuend, and T. Peter (2012), Liquid-liquid phase separation in aerosol particles: Dependence on O:C, organic functionalities, and compositional complexity, Geophys. Res. Lett., 39doi:10.1029/2012GL052807.

Purification of heavy metal loaded wastewater from electroplating industry under synthesis of delafossite (ABO2) by "Lt-delafossite process".

PubMed

John, Melanie; Heuss-Aßbichler, Soraya; Ullrich, Aladin; Rettenwander, Daniel

2016-09-01

In this study we present a new, environmental friendly and economic method, called Lt-delafossite process to treat industrial wastewater (initial Cu(2+)-concentrations of 1-15.6 g/l) by subsequent synthesis of nano-crystalline (doped) delafossite (CuFeO2) solely by precipitation and ageing at temperatures between 50 °C and 90 °C. The reached water purification rates are exclusively ≥99.99% for both wastewater models and wastewaters from electroplating industry. We succeeded to synthesize a mixture of 3R and 2H delafossite at 50 °C after 90 h and ≥70 °C after 16 h of ageing directly from industrial wastewater without any additional phases. In all cases green rust (GR), a Fe(II-III) layered double hydroxysulphate, Cu2O (cuprite) and Fe10O14(OH)2 (ferrihydrite) precipitates first. During ageing of the residues the metastable phases transform to delafossite. The residues are characterized by XRD, FTIR, SEM, TEM, VFTB and Mößbauer measurements. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hot gas, regenerative, supported H.sub.2 S sorbents

NASA Technical Reports Server (NTRS)

Voecks, Gerald E. (Inventor); Sharma, Pramod K. (Inventor)

1993-01-01

Efficient, regenerable sorbents for removal of H.sub.2 S from moderately high temperature (usually 200.degree. C.-550.degree.C.) gas streams comprise a porous, high surface area aluminosilicate support, suitably a zeolite, and most preferably a sodium deficient zeolite containing 1 to 20 weight percent of binary metal oxides. The binary oxides are a mixture of a Group VB or VIB metal oxide with a Group IB, IIB or VIII metal oxide such as V-Zn-O, V-Cu-O, Cu-Mo-O, Zn-Mo-O or Fe-Mo-O contained in the support. The sorbent effectively removes H.sub.2 S from the host gas stream in high efficiency and can be repetitively regenerated at least 10 times without loss of activity.

Measurements and kinetic modeling of atomic species in fuel-oxidizer mixtures excited by a repetitive nanosecond pulse discharge

NASA Astrophysics Data System (ADS)

Winters, C.; Eckert, Z.; Yin, Z.; Frederickson, K.; Adamovich, I. V.

2018-01-01

This work presents the results of number density measurements of metastable Ar atoms and ground state H atoms in diluted mixtures of H2 and O2 with Ar, as well as ground state O atoms in diluted H2-O2-Ar, CH4-O2-Ar, C3H8-O2-Ar, and C2H4-O2-Ar mixtures excited by a repetitive nanosecond pulse discharge. The measurements have been made in a nanosecond pulse, double dielectric barrier discharge plasma sustained in a flow reactor between two plane electrodes encapsulated within dielectric material, at an initial temperature of 500 K and pressures ranging from 300 Torr to 700 Torr. Metastable Ar atom number density distribution in the afterglow is measured by tunable diode laser absorption spectroscopy, and used to characterize plasma uniformity. Temperature rise in the reacting flow is measured by Rayleigh scattering. H atom and O atom number densities are measured by two-photon absorption laser induced fluorescence. The results are compared with kinetic model predictions, showing good agreement, with the exception of extremely lean mixtures. O atoms and H atoms in the plasma are produced mainly during quenching of electronically excited Ar atoms generated by electron impact. In H2-Ar and O2-Ar mixtures, the atoms decay by three-body recombination. In H2-O2-Ar, CH4-O2-Ar, and C3H8-O2-Ar mixtures, O atoms decay in a reaction with OH, generated during H atom reaction with HO2, with the latter produced by three-body H atom recombination with O2. The net process of O atom decay is O  +  H  →  OH, such that the decay rate is controlled by the amount of H atoms produced in the discharge. In extra lean mixtures of propane and ethylene with O2-Ar the model underpredicts the O atom decay rate. At these conditions, when fuel is completely oxidized by the end of the discharge burst, the net process of O atom decay, O  +  O  →  O2, becomes nearly independent of H atom number density. Lack of agreement with the data at these conditions is likely due to diffusion of H atoms from the partially oxidized regions near the side walls of the reactor into the plasma. Although significant fractions of hydrogen and hydrocarbon fuels are oxidized by O atoms produced in the plasma, chain branching remains a minor effect at these relatively low temperature conditions.

Assessment of the biopotency of follitropin alfa and lutropin alfa combined in one injection: a comparative trial in Sprague-Dawley rats

PubMed Central

Alper, Michael; Meyer, Randal; Dekkers, Chris; Ezcurra, Diego; Schertz, Joan; Kelly, Eduardo

2008-01-01

Background The current study was designed to determine if follitropin alfa (recombinant human follicle-stimulating hormone; r-hFSH) and lutropin alfa (recombinant human luteinizing hormone; r-hLH) biopotencies were unchanged by reconstituting in sterile water for injection and mixing prior to injection. Methods The biopotencies of r-hFSH and r-hLH were determined following injection of female Sprague-Dawley rats with a mixture of follitropin alfa revised formulation female (RFF) and lutropin alfa (1:1, r-hFSH:r-hLH). Biopotencies of follitropin alfa RFF and lutropin alfa were measured using ovarian weight and ascorbic acid depletion assays, respectively, and compared with a reference standard. Stock mixtures of follitropin alfa RFF and lutropin alfa (1:1) were prepared within 1 h prior to each respective assay's injection and stored at 6 +/- 2°C. Separate low dose (follitropin alfa RFF 1.5 IU/rat, lutropin alfa 2 IU/rat) and high dose (follitropin alfa RFF 3 IU/rat, lutropin alfa 8 IU/rat) treatments were prepared from stock mixtures or individual solutions by diluting with 0.22% bovine serum albumin saline solution and injected within 1 h of preparation. The main outcome measures were ovarian weight and ovarian ascorbic acid depletion. Results FSH bioactivities were similar (p > 0.10) between the individual follitropin alfa RFF test solution (84.2 IU) and follitropin alfa RFF/lutropin alfa (87.6 IU) mixtures prepared within 1 h of injection and stored at 6 +/- 2°C. LH bioactivities were similar (p > 0.10) between lutropin alfa (94.7 IU) test solution and lutropin alfa/follitropin alfa RFF (85.3 IU) mixtures prepared within 1 h of injection and stored at 6 +/- 2°C for not more than 1 h prior to injection. Conclusion Mixing follitropin alfa RFF and lutropin alfa did not alter the bioactivity of either FSH or LH. PMID:18647398

Synthesis of renewable high-density fuel with isophorone.

PubMed

Wang, Wei; Liu, Yanting; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2017-07-21

1,1,3-Trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane, a renewable high density fuel, was first produced in a high overall carbon yield (~70%) with isophorone which can be derived from hemicellulose. The synthetic route used this work contains three steps. In the first step, 3,3,5-trimethylcyclohexanone was synthesized by the selective hydrogenation of isophorone. Among the investigated catalysts, the Pd/C exhibited the highest activity and selectivity. Over this catalyst, a high carbon yield (99.0%) of 3,3,5-trimethylcyclohexanone was achieved under mild conditions (298 K, 2 MPa H 2 , 1 h). In the second step, 3,5,5-trimethyl-2-(3,3,5-trimethylcyclohexylidene)cyclohexanone was produced in a high carbon yield (76.4%) by the NaOH catalyzed self-aldol condensation of 3,3,5-trimethylcyclohexanone which was carried out in a round bottom flask attached to the Dean-Stark apparatus. In the third step, the 3,5,5-trimethyl-2-(3,3,5-trimethylcyclohexylidene)cyclohexanone was hydrodeoxygenated under solvent-free conditions. High carbon yield (93.4%) of 1,1,3-trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane was obtained over the Ni/SiO 2 catalyst. The 1,1,3-trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane as obtained has a density of 0.858 g mL -1 and a freezing point of 222.2 K. As a potential application, it can be blended into conventional fuels (such as RP-1, RG-1, etc.) for rocket propulsion.

Cocrystals of 6-propyl-2-thiouracil: N-H···O versus N-H···S hydrogen bonds.

PubMed

Tutughamiarso, Maya; Egert, Ernst

2011-11-01

In order to investigate the relative stability of N-H···O and N-H···S hydrogen bonds, we cocrystallized the antithyroid drug 6-propyl-2-thiouracil with two complementary heterocycles. In the cocrystal pyrimidin-2-amine-6-propyl-2-thiouracil (1/2), C(4)H(5)N(3)·2C(7)H(10)N(2)OS, (I), the `base pair' is connected by one N-H···S and one N-H···N hydrogen bond. Homodimers of 6-propyl-2-thiouracil linked by two N-H···S hydrogen bonds are observed in the cocrystal N-(6-acetamidopyridin-2-yl)acetamide-6-propyl-2-thiouracil (1/2), C(9)H(11)N(3)O(2)·2C(7)H(10)N(2)OS, (II). The crystal structure of 6-propyl-2-thiouracil itself, C(7)H(10)N(2)OS, (III), is stabilized by pairwise N-H···O and N-H···S hydrogen bonds. In all three structures, N-H···S hydrogen bonds occur only within R(2)(2)(8) patterns, whereas N-H···O hydrogen bonds tend to connect the homo- and heterodimers into extended networks. In agreement with related structures, the hydrogen-bonding capability of C=O and C=S groups seems to be comparable.

Homogeneous reduction of CO2 by photogenerated pyridinyl radicals.

PubMed

Riboni, Francesca; Selli, Elena; Hoffmann, M R; Colussi, A J

2015-05-14

We report that 1-hydropyridinyl radicals (1-PyH(•)) photogenerated in solution react with dissolved CO2 en route to its 2e(-) reduction into carboxylic acids. The 254 nm excitation of pyridine (Py) in deaerated 2-PrOH/H2O mixtures saturated with 1 atm of CO2 yields a suite of products, among which we identified Na(HCOO)2(-) (m/z(-) = 113), C5H6NCOO(-) (m/z(-) = 124), and C5H10O2NCOO(-) (m/z(-) = 160) species by electrospray ionization mass spectrometry. These products demonstrably contain carboxylate functionalities that split CO2 neutrals via collisionally induced dissociation. We infer that 1-PyH(•) [from (1) (3)Py* + 2-PrOH → 1-PyH(•) + (•)PrOH] adds to CO2, in competition with radical-radical reactions, leading to intermediates that are in turn reduced by (•)PrOH into the observed species. The formation of carboxylates in this system, which is shown to require CO2, Py, 2-PrOH, and actinic radiation, amounts to the homogeneous 2e(-) reduction of CO2 by 2-PrOH initiated by Py*. We evaluate a rate constant (2) k2(1-PyH(•) + CO2 → (•)Py-1-COOH) ≈ O (10) M(-1) s(-1) and an activation energy E2 ≥ 9 kcal mol(-1) that are compatible with thermochemical estimates for this reaction.

Selective oxidation of rhodinol to citral using H{sub 2}O{sub 2}-platinum black system under microwave irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chong, D. J. W.; Latip, J.; Hasbullah, S. A.

2014-09-03

The oxidation method utilising H{sub 2}O{sub 2}-Pt black system was successfully adapted in the oxidation of rhodinol which is a mixture form of geraniol and citronellol. This green oxidation found to be selectively converted geraniol to citral using conventional method. The implementation of microwave irradiation (175 Watt, 90°C, 30 mins) and a higher molar of H{sub 2}O{sub 2} further improved the conversion rate (72.6%) and selectivity (81%) as compared to the conventional method.

Selective oxidation of rhodinol to citral using H2O2-platinum black system under microwave irradiation

NASA Astrophysics Data System (ADS)

Chong, D. J. W.; Latip, J.; Hasbullah, S. A.; Sastrohamidjojo, H.

2014-09-01

The oxidation method utilising H2O2-Pt black system was successfully adapted in the oxidation of rhodinol which is a mixture form of geraniol and citronellol. This green oxidation found to be selectively converted geraniol to citral using conventional method. The implementation of microwave irradiation (175 Watt, 90°C, 30 mins) and a higher molar of H2O2 further improved the conversion rate (72.6%) and selectivity (81%) as compared to the conventional method.

The influence of insulin-dependent diabetes mellitus (IDDM) duration on superoxide anion and hydrogen peroxide production by polymorphonuclear neutrophils.

PubMed

Zozulińska, D A; Wierusz-Wysocka, B; Wysocki, H; Majchrzak, A E; Wykretowicz, A

1996-08-01

We address the question whether oxygen metabolism of polymorphonuclear neutrophils (PMN) is influenced by disease duration in patients with insulin-dependent diabetes mellitus (IDDM). PMN were isolated from patients with IDDM of various durations and from healthy controls. We measured PMN production of superoxide anions (O2-) by cytochrome c reduction (see Babior, B.M. et al. (1973) J. Clin. Invest. 52, 741-746) and PMN production of hydrogen peroxide (H2O2) by phenol red oxygenation (see Pick, E. (1980) J. Immunol. Methods 38, 161-169) in three groups of IDDM patients subdivided according to disease duration (group A: IDDM less that 10 years; group B: IDDM of 10-15 years; group C: IDDM of more than 15 years) and in control healthy subjects (group H). Unstimulated O2- production in all IDDM patients was not statistically different from control values (A: 4.3 +/- 0.4 nmol/10(6) PMN per 30 min, nmol/10(6) PMN per 30 min; C: 4.9 +/- 0.9 nmol/10(6) PMN per 30 min; and H: 3.5 +/- 0.2 nmol/10(6) PMN per 30 min, respectively). In contrast, stimulated O2- production was significantly lower in both patients with 10-15 years, and patients with more than 15 years, duration of IDDM than in controls (B: 25.7 +/- 2.5 nmol/10(6) PMN per 30 min; C: 21.1 +/- 3.4 nmol/10(6) PMN per 30 min and H: 42.2 +/- 1.1 nmol/10(6) PMN per 30 min, respectively) correlating with disease duration (r = -0.44, P < 0.033). The stimulated O2- production in patients with less than 10 years duration of IDDM (A: 35.7 +/- 1.9 nmol/10(6) PMN per 30 min) was slightly lower than in controls. H2O2 production of unstimulated PMN (A: 4.0 +/- 0.5 nmol/10(6) PMN per 30 min; B: 4.4 +/- 0.8 nmol/10(6) PMN per 30 min and C: 4.4 +/-1.0 nmol/10(6) PMN per 30 min, respectively) was much higher than those in controls. In contrast, stimulated H2O2 production did not differ statistically from the value noticed in healthy subjects. The results obtained might indicate that production of H2O2 by unstimulated cells is increased in diabetic patients while generation of O2- by stimulated neutrophils is markedly impaired, suggesting that toxic oxygen species production might be influenced by disease duration.

Scandium complexes with the tetraphenylethylene and anthracene dianions.

PubMed

Ellis, John E; Minyaev, Mikhail E; Nifant'ev, Ilya E; Churakov, Andrei V

2018-06-01

The structural study of Sc complexes containing dianions of anthracene and tetraphenylethylene should shed some light on the nature of rare-earth metal-carbon bonding. The crystal structures of (18-crown-6)bis(tetrahydrofuran-κO)sodium bis(η 6 -1,1,2,2-tetraphenylethenediyl)scandium(III) tetrahydrofuran disolvate, [Na(C 4 H 8 O) 2 (C 12 H 24 O 6 )][Sc(C 26 H 20 ) 2 ]·2C 4 H 8 O or [Na(18-crown-6)(THF) 2 ][Sc(η 6 -C 2 Ph 4 ) 2 ]·2(THF), (1b), (η 5 -1,3-diphenylcyclopentadienyl)(tetrahydrofuran-κO)(η 6 -1,1,2,2-tetraphenylethenediyl)scandium(III) toluene hemisolvate, [Sc(C 17 H 13 )(C 26 H 20 )(C 4 H 8 O)]·0.5C 7 H 8 or [(η 5 -1,3-Ph 2 C 5 H 3 )Sc(η 6 -C 2 Ph 4 )(THF)]·0.5(toluene), (5b), poly[[(μ 2 -η 3 :η 3 -anthracenediyl)bis(η 6 -anthracenediyl)bis(η 5 -1,3-diphenylcyclopentadienyl)tetrakis(tetrahydrofuran)dipotassiumdiscandium(III)] tetrahydrofuran monosolvate], {[K 2 Sc 2 (C 14 H 10 ) 3 (C 17 H 13 ) 2 (C 4 H 8 O) 4 ]·C 4 H 8 O} n or [K(THF) 2 ] 2 [(1,3-Ph 2 C 5 H 3 ) 2 Sc 2 (C 14 H 10 ) 3 ]·THF, (6), and 1,4-diphenylcyclopenta-1,3-diene, C 17 H 14 , (3a), have been established. The [Sc(η 6 -C 2 Ph 4 ) 2 ] - complex anion in (1b) contains the tetraphenylethylene dianion in a symmetrical bis-η 3 -allyl coordination mode. The complex homoleptic [Sc(η 6 -C 2 Ph 4 ) 2 ] - anion retains its structure in THF solution, displaying hindered rotation of the coordinated phenyl rings. The 1D 1 H and 13 C{ 1 H}, and 2D COSY 1 H- 1 H and 13 C- 1 H NMR data are presented for M[Sc(Ph 4 C 2 ) 2 ]·xTHF [M = Na and x = 4 for (1a); M = K and x = 3.5 for (2a)] in THF-d 8 media. Complex (5b) exhibits an unsymmetrical bis-η 3 -allyl coordination mode of the dianion, but this changes to a η 4 coordination mode for (1,3-Ph 2 C 5 H 3 )Sc(Ph 4 C 2 )(THF) 2 , (5a), in THF-d 8 solution. A 45 Sc NMR study of (2a) and UV-Vis studies of (1a), (2a) and (5a) indicate a significant covalent contribution to the Sc-Ph 4 C 2 bond character. The unique Sc ate complex, (6), contains three anthracenide dianions demonstrating both a η 6 -coordination mode for two bent ligands and a μ 2 -η 3 :η 3 -bridging mode of a flat ligand. Each [(1,3-Ph 2 C 5 H 3 ) 2 Sc 2 (C 14 H 10 ) 3 ] 2- dianionic unit is connected to four neighbouring units via short contacts with [K(THF) 2 ] + cations, forming a two-dimensional coordination polymer framework parallel to (001).

Analysis of ferrite nanoparticles in the flow of ferromagnetic nanofluid.

PubMed

Muhammad, Noor; Nadeem, Sohail; Mustafa, M T

2018-01-01

Theoretical analysis has been carried out to establish the heat transport phenomenon of six different ferromagnetic MnZnFe2O4-C2H6O2 (manganese zinc ferrite-ethylene glycol), NiZnFe2O4-C2H6O2 (Nickel zinc ferrite-ethylene glycol), Fe2O4-C2H6O2 (magnetite ferrite-ethylene glycol), NiZnFe2O4-H2O (Nickel zinc ferrite-water), MnZnFe2O4-H2O (manganese zinc ferrite-water), and Fe2O4-H2O (magnetite ferrite-water) nanofluids containing manganese zinc ferrite, Nickel zinc ferrite, and magnetite ferrite nanoparticles dispersed in a base fluid of ethylene glycol and water mixture. The performance of convective heat transfer is elevated in boundary layer flow region via nanoparticles. Magnetic dipole in presence of ferrites nanoparticles plays a vital role in controlling the thermal and momentum boundary layers. In perspective of this, the impacts of magnetic dipole on the nano boundary layer, steady, and laminar flow of incompressible ferromagnetic nanofluids are analyzed in the present study. Flow is caused by linear stretching of the surface. Fourier's law of heat conduction is used in the evaluation of heat flux. Impacts of emerging parameters on the magneto-thermomechanical coupling are analyzed numerically. Further, it is evident that Newtonian heating has increasing behavior on the rate of heat transfer in the boundary layer. Comparison with available results for specific cases show an excellent agreement.

The gas-phase ozonolysis of α-humulene.

PubMed

Beck, M; Winterhalter, R; Herrmann, F; Moortgat, G K

2011-06-21

α-Humulene contains three double bonds (DB), and after ozonolysis of the first DB the first-generation products are still reactive towards O(3) and produce second- and third-generation products. The primary aim of this study consisted of identifying the products of the three generations, focusing on the carboxylic acids, which are known to have a high aerosol formation potential. The experiments were performed in a 570 litre spherical glass reactor at 295 K and 730 Torr. Initial mixing ratios were 260-2090 ppb for O(3) and 250-600 ppb for α-humulene in synthetic air. Reactants and gas-phase products were measured by in situ FTIR spectroscopy. Particulate products were sampled on Teflon filters, extracted with methanol and analyzed by LC-MS/MS-TOF. Using cyclohexane (10-100 ppm) as an OH-radical scavenger and by monitoring the yield of cyclohexanone by PTR-MS, an OH-yield of (10.5 ± 0.7)% was determined for the ozonolysis of the first DB, and (12.9 ± 0.7)% of the first-generation products. The rate constant of the reaction of O(3) with α-humulene is known as k(0) = 1.17 × 10(-14) cm(3) molecule(-1) s(-1) [Y. Shu and R. Atkinson, Int. J. Chem. Kinet., 1994, 26, 1193-1205]. The reaction rate constants of O(3) with the first-generation products and the second-generation products were, respectively, determined as k(1) = (3.6 ± 0.9) × 10(-16) and k(2) = (3.0 ± 0.7) × 10(-17) cm(3) molecule(-1) s(-1) by Facsimile-simulation of the observed ozone decay by FTIR. A total of 37 compounds in the aerosol phase and 5 products in the gas phase were tentatively identified: 25 compounds of the first-generation products contained C13-C15 species, 9 compounds of the second-generation products contained C8-C11 species, whereas 8 compounds of the third-generation products contained C4-C6 species. The products of all three generations consisted of a variety of dicarboxylic-, hydroxy-oxocarboxylic- and oxo-carboxylic acids. The formation mechanisms of some of the products are discussed. The residual FTIR spectra indicate the formation of secondary ozonides (SOZ) in the gas phase, which are formed by the intramolecular reaction of the Criegee moiety with the carbonyl endgroup. These SOZ revealed to be stable over several hours and its formation was shown not to be affected by the addition of Criegee-radical scavengers such as HCOOH or H(2)O. This suggests that in the ozonolysis of α-humulene at atmospheric pressures the POZ will decompose rapidly, and that a large fraction of the formed exited Criegee Intermediate will be stabilized to form stable SOZ, while the formation of OH-radicals via the hydroperoxide channel will be a minor process.

Ultrafine Nanocrystalline CeO2@C-Containing NaAlH4 with Fast Kinetics and Good Reversibility for Hydrogen Storage.

PubMed

Zhang, Xin; Liu, Yongfeng; Wang, Ke; Li, You; Gao, Mingxia; Pan, Hongge

2015-12-21

A nanocrystalline CeO2@C-containing NaAlH4 composite is successfully synthesized in situ by hydrogenating a NaH-Al mixture doped with CeO2@C. Compared with NaAlH4 , the as-prepared CeO2@C-containing NaAlH4 composite, with a minor amount of excess Al, exhibits significantly improved hydrogen storage properties. The dehydrogenation onset temperature of the hydrogenated [NaH-Al-7 wt % CeO2@C]-0.04Al sample is 77 °C lower than that of the pristine sample because of a reduced kinetic barrier. More importantly, the dehydrogenated sample absorbs ∼4.7 wt % hydrogen within 35 min at 100°C and 10 MPa of hydrogen. Compositional and structural analyses reveal that CeO2 is converted to CeH2 during ball milling and that the newly formed CeH2 works with the excess of Al to synergistically improve the hydrogen storage properties of NaAlH4. Our findings will aid in the rational design of novel catalyst-doped complex hydride systems with low operating temperatures, fast kinetics, and long-term cyclability. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

(η(6)-Benzene)(carbonato-κ(2) O,O')[di-cyclohex-yl(naphthalen-1-ylmeth-yl)phosphane-κP]ruthenium(II) chloro-form tris-olvate.

PubMed

Gowrisankar, Saravanan; Neumann, Helfried; Spannenberg, Anke; Beller, Matthias

2014-07-01

The title compound, [Ru(CO3)(η(6)-C6H6){(C6H11)2P(CH2C10H7)}]·3CHCl3, was synthesized by carbonation of [RuCl2(η(6)-C6H6){(C6H11)2P(CH2C10H7)}] with NaHCO3 in methanol at room temperature. The Ru(II) atom is surrounded by a benzene ligand, a chelating carbonate group and a phosphane ligand in a piano-stool configuration. The crystal packing is consolidated by C-H⋯O and C-H⋯Cl hydrogen-bonding inter-actions between adjacent metal complexes and between the complexes and the solvent mol-ecules. The asymmetric unit contains one metal complex and three chloro-form solvent mol-ecules of which only one was modelled. The estimated diffraction contributions of the other two strongly disordered chloro-form solvent mol-ecules were substracted from the observed diffraction data using the SQUEEZE procedure in PLATON [Spek (2009 ▶). Acta Cryst. D65, 148-155].

A Family of Uranyl Coordination Polymers Containing O-Donor Dicarboxylates and Trispyridyltriazine Guests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thangavelu, Sonia G.; Cahill, Christopher L.

Four uranyl coordination polymers [UO2(C6H8O4)(H2O)2](C18H12N6)2 (1), [UO2(C8H4O4)(H2O)2](C18H12N6)2 (2), Na[(UO2)(C12H6O4)2](C18H13N6)·H2O (3), and Na[(UO2)(C16H8O4)(C6H3NO2)](C18H12N6)·H2O (4) containing aliphatic (adipic acid) or aromatic linkers (1,4-benzene dicarboxylic acid (BDC), 1,4-napthalene dicarboxylic acid (NDC), anthracene 9,10-dicarboxylic acid (ADC)) were synthesized and characterized using single crystal X-ray diffraction, powder X-ray diffraction, and luminescence spectroscopy. The π-stacking distances or the number of π–π interactions present between trispyridyltriazine (TPTZ) guests or the host framework in 1–4 may be affected by the size of the O-donor linker (adipic acid < BDC < NDC < ADC). Luminescence studies show that substitution between adipic acid and BDC influences the emission of 1more » and 2, in which the emission of 1 shows a red shift relative to that of 2. Uranyl emission was not observed in 3 and 4, and may be attributed to the position of the NDC and ADC triplet state relative to the emissive uranyl species.« less

A Family of Uranyl Coordination Polymers Containing O-Donor Dicarboxylates and Trispyridyltriazine Guests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thangavelu, Sonia G.; Cahill, Christopher L.

2016-01-06

Four uranyl coordination polymers [UO2(C6H8O4)(H2O)2](C18H12N6)2 (1), [UO2(C8H4O4)(H2O)2](C18H12N6)2 (2), Na[(UO2)(C12H6O4)2](C18H13N6)·H2O (3), and Na[(UO2)(C16H8O4)(C6H3NO2)](C18H12N6)·H2O (4) containing aliphatic (adipic acid) or aromatic linkers (1,4-benzene dicarboxylic acid (BDC), 1,4-napthalene dicarboxylic acid (NDC), anthracene 9,10-dicarboxylic acid (ADC)) were synthesized and characterized using single crystal X-ray diffraction, powder X-ray diffraction, and luminescence spectroscopy. The π-stacking distances or the number of π–π interactions present between trispyridyltriazine (TPTZ) guests or the host framework in 1–4 may be affected by the size of the O-donor linker (adipic acid < BDC < NDC < ADC). Luminescence studies show that substitution between adipic acid and BDC influences the emission of 1more » and 2, in which the emission of 1 shows a red shift relative to that of 2. Uranyl emission was not observed in 3 and 4, and may be attributed to the position of the NDC and ADC triplet state relative to the emissive uranyl species.« less

Intramolecular chalcogen-tin interactions in [(o-MeE-C6H4)CH2]2SnPh2-nCln; E = S, O, CH2, n = 0, 1, 2 and intermolecular chlorine-tin interactions in the meta and para-methoxy isomers

PubMed Central

Vargas-Pineda, Diana Gabriela; Guardado, Tanya; Cervantes-Lee, Francisco; Metta-Magana, Alejandro J.

2010-01-01

Organotin(IV) compounds of the type [(o-MeE-C6H4)CH2]2SnPh2-nCln were synthesized, E = O, n = 0 (1), n = 1 (2), n = 2 (3), E = S, n = 0 (4), n = 1 (5), n = 2 (6) and E = CH2, n = 0 (7), n = 1 (8), n = 2 (9). The dichloro compounds 3 and 6 have been investigated by single crystal X-ray diffraction and exhibit bi-capped tetrahedral geometry at the tin atom as a consequence of significant intramolecular Sn⋯O (3) and Sn⋯S (6) secondary bonding, in monomolecular units. Compound 3 when crystallized from a hexane/thf solvent mixture shows two different conformers, 3′ and 3″, in the crystal structure, 3′ has two equivalent Sn⋯O interactions, while 3″ has two non-equivalent Sn⋯O interactions. Upon recrystallization of 3 from hexane only a single structural form is observed, 3′. The Sn⋯E distances in 3′, 3″, and 6 are 71.3; 73.5, 72.9; and 76.3% of the ΣvdW radii, respectively. The meta and para-substituted isomers of 3 (10, 11) exhibit a distortion at the tin atom due to self-association via intermolecular Sn⋯Cl interactions resulting in polymeric structures. 119Sn NMR spectroscopy suggests that the intramolecular Sn⋯E interactions persist in solution for the dichloride compounds 3 and 6. PMID:20047301

Crystal structures of dioxonium hexafluorotantalate and dioxonium hexafluoroniobate complexes with tetrabenzo-30-crown-10

DOE Office of Scientific and Technical Information (OSTI.GOV)

Furmanova, N. G., E-mail: furm@ns.crys.ras.ru; Rabadanov, M. Kh.; Chernaya, T. S.

2008-03-15

Two isostructural complexes of dioxonium [H{sub 5}O{sub 2}]{sup +} with tetrabenzo-30-crown-10 of the compositions [(tetrabenzo-30-crown-10 . H{sub 5}O{sub 2})][TaF{sub 6}] (I) and [(tetrabenzo-30-crown-10 . H{sub 5}O{sub 2})][NbF{sub 6}] (II) are studied using X-ray diffraction. The complexes crystallize in the monoclinic crystal system (space group C2/c, Z = 4). The unit cell parameters of these compounds are as follows: a = 15.6583(12) A, b = 15.2259(13) A, c = 16.4473(13) A, and {beta} = 99.398(6) deg. for complex I and a = 15.7117(12) A, b = 15.2785(15) A, c = 16.5247(15) A, and {beta} = 99.398(7) deg. for complex II. Thesemore » complexes belong to the ionic type. The dioxonium cation [H{sub 5}O{sub 2}]{sup +} in the form of the two-unit cluster [H{sub 3}O . H{sub 2}O]{sup +} is stabilized by the strong hydrogen bond OH-O [O-O, 2.353(4) A] and encapsulated by the crown ether. Each oxygen atom of the dioxonium cation also forms two oxygen bonds O-O(crown). The crown ether adopts an unusual two-level (pocket-like) conformation, which provides a complete encapsulation of the oxonium associate. The interaction of the cationic complex with the anion in the crystal occurs through contacts of the C-H-F type.« less

Crystal structures of dioxonium hexafluorotantalate and dioxonium hexafluoroniobate complexes with tetrabenzo-30-crown-10

NASA Astrophysics Data System (ADS)

Furmanova, N. G.; Rabadanov, M. Kh.; Chernaya, T. S.; Fonari, M. S.; Simonov, Yu. A.; Ganin, É. V.; Gelmboldt, V. O.; Grigorash, R. Ya.; Kotlyar, S. A.; Kamalov, G. L.

2008-03-01

Two isostructural complexes of dioxonium [H5O2]+ with tetrabenzo-30-crown-10 of the compositions [(tetrabenzo-30-crown-10 · H5O2)][TaF6] ( I) and [(tetrabenzo-30-crown-10 · H5O2)][NbF6] ( II) are studied using X-ray diffraction. The complexes crystallize in the monoclinic crystal system (space group C2/ c, Z = 4). The unit cell parameters of these compounds are as follows: a = 15.6583(12) Å, b = 15.2259(13) Å, c = 16.4473(13) Å, and β = 99.398(6)° for complex I and a = 15.7117(12) Å, b = 15.2785(15) Å, c = 16.5247(15) Å, and β = 99.398(7)° for complex II. These complexes belong to the ionic type. The dioxonium cation [H5O2]+ in the form of the two-unit cluster [H3O · H2O]+ is stabilized by the strong hydrogen bond OH⋯O [O⋯O, 2.353(4) Å] and encapsulated by the crown ether. Each oxygen atom of the dioxonium cation also forms two oxygen bonds O⋯O(crown). The crown ether adopts an unusual two-level (pocket-like) conformation, which provides a complete encapsulation of the oxonium associate. The interaction of the cationic complex with the anion in the crystal occurs through contacts of the C-H⋯F type.

Steady-state studies of the reactions of H2O-CO and CO2-H2 mixtures with liquid iron

NASA Astrophysics Data System (ADS)

Sasaki, Y.; Belton, G. R.

1998-08-01

Studies have been made of the steady-stata composition of liquid iron exposed to high flow rates of H2O-CO mixtures at 1550 °C to 1700 °C and CO2-H2 mixtures at 1600 °C. Values of the steady-state activity of oxygen have been established by measurement of either the carbon concentration or the silicon concentration when the iron was held in a silica crucible. Additions of sulfur or selenium to the iron have been found to result in steady-state oxygen activities, which differ significantly from those expected from water-gas equilibrium. The results are interpreted to show that the ratio of the apparent first-order rate constants for the reactions of H2O and CO2 with liquid iron is about 3 at 1600 °C. It is shown that the dependencies of the rate constants on the activities of sulfur, oxygen, and selenium must, even if complex, be similar for the H2O and CO2 reactions with liquid iron, to a good approximation.

Synthesis, structure and reactivity of rare-earth metallacarborane alkyls [η(1):η(5)-O(CH2)2C2B9H9]Ln(σ:η(1)-CH2C6H4-o-NMe2)(THF)2.

PubMed

Yang, Jingying; Xie, Zuowei

2015-04-14

Rare-earth metallacarborane alkyls can be stabilized by the incorporation of a functional sidearm into both π and σ ligands. Reaction of [Me3NH][7,8-O(CH2)2-7,8-C2B9H10] with one equiv. of Ln(CH2C6H4-o-NMe2)3 gave metallacarborane alkyls [η(1):η(5)-O(CH2)2C2B9H9]Ln(σ:η(1)-CH2C6H4-o-NMe2)(THF)2 (Ln = Y (), Gd (), Er ()) via alkane elimination. They represent the first examples of rare-earth metallacarborane alkyls. Treatment of with RN[double bond, length as m-dash]C[double bond, length as m-dash]NR (R = Cy, (i)Pr) or 2-benzoylpyridine afforded the corresponding mono-insertion products [η(1):η(5)-O(CH2)2C2B9H9]Y[η(2)-(RN)2C(CH2C6H4-o-NMe2)](DME) (R = Cy (), (i)Pr ()) or [η(1):η(5)-O(CH2)2C2B9H9]Y[C5H4NC(Ph)(CH2C6H4-o-NMe2)O](THF)2 (), respectively. Complex also reacted with ArNCO or ArNC (Ar = 2,6-diisopropylphenyl, 2,6-dimethylphenyl) to give di-insertion products [η(1):η(5)-O(CH2)2C2B9H9]Y[OC([double bond, length as m-dash]NC6H3Me2)N(C6H3Me2)C(CH2C6H4-o-NMe2)O](THF)2 () or [η(1):η(5)-O(CH2)2C2B9H9]Y[C([double bond, length as m-dash]NC6H3(i)Pr2)C([double bond, length as m-dash]NC6H3(i)Pr2)(CH2C6H4-o-NMe2)](DME) (). These results showed that the reactivity pattern of the Ln-C σ bond in rare-earth metallacarborane alkyls was dependent on the nature of the unsaturated organic molecules. New complexes were characterized by various spectroscopic techniques and elemental analysis. Some were further confirmed by single-crystal X-ray analysis.

Characterization of hallucinogenic phenethylamines using high-resolution mass spectrometry for non-targeted screening purposes.

PubMed

Pasin, Daniel; Cawley, Adam; Bidny, Sergei; Fu, Shanlin

2017-10-01

Hallucinogenic phenethylamines such as 2,5-dimethoxyphenethylamines (2C-X) and their N-(2-methoxybenzyl) derivatives (25X-NBOMe) have seen an increase in novel analogues in recent years. These rapidly changing analogues make it difficult for laboratories to rely on traditional targeted screening methods to detect unknown new psychoactive substances (NPS). In this study, twelve 2C-X, six 2,5-dimethoxyamphetamines (DOX), and fourteen 25X-NBOMe derivatives, including two deuterated derivatives (2C-B-d 6 and 25I-NBOMe-d 9 ), were analyzed using ultra-performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UPLC-QTOF-MS). Collision-induced dissociation (CID) experiments were performed using collision energies set at 10, 20, and 40 eV. For 2C-X and DOX derivatives, common losses were observed including neutral and radical losses such as NH 3 (17.0265 Da), •CH 6 N (32.0500 Da), C 2 H 7 N (45.0578 Da) and C 2 H 9 N (47.0735 Da). 2C-X derivatives displayed common product ions at m/z 164.0837 ([C 10 H 12 O 2 ] +• ), 149.0603 ([C 9 H 9 O 2 ] + ), and 134.0732 ([C 9 H 10 O] +• ) while DOX derivatives had common product ions at m/z 178.0994 ([C 11 H 14 O 2 ] +• ), 163.0754 ([C 10 H 11 O 2 ] + ), 147.0804 ([C 10 H 11 O] + ), and 135.0810 ([C 9 H 11 O] + ). 25X-NBOMe had characteristic product ions at m/z 121.0654 ([C 8 H 9 O] + ) and 91.0548 ([C 7 H 7 ] + ) with minor common losses corresponding to 2-methylanisole (C 8 H 10 O, 122.0732 Da), 2-methoxybenzylamine (C 8 H 11 NO, 137.0847 Da), and •C 9 H 14 NO (152.1074 Da). Novel analogues of the selected classes can be detected by applying neutral loss filters (NLFs) and extracting the common product ions. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

Synthesis and characterization of two novel inorganic/organic hybrid materials based on polyoxomolybdate clusters: (C5H5N5)2(C5H6N5)4[(HAsO4)2Mo6O18]·11H2O and Na2(Himi)3[SeMo6O21(CH3COO)3]·6H2O

NASA Astrophysics Data System (ADS)

Ayed, Meriem; Mestiri, Imen; Ayed, Brahim; Haddad, Amor

2017-01-01

Two new organic-inorganic hybrid compound, (C5H5N5)2(C5H6N5)4[(HAsO4)2Mo6O18]·11H2O (I) and Na2(Himi)3[SeMo6O21(CH3COO)3]·6H2O (II) were synthesized and structurally characterized by scanning electron microscopy (SEM), elemental analyses, FTIR, UV spectroscopy, thermal stability analysis, XRD and single crystal X-ray diffraction. Crystal data: (I) triclinic system, space group P-1, a = 11,217 (9) Å, b = 11,637 (8) Å, c = 14,919 (8) Å, α = 70,90 (5)°, β = 70,83 (2)°, γ = 62,00(1)° and Z = 1; (II) triclinic system, space group P-1, a = 10.6740(1) Å, b = 10.6740(1) Å, c = 20.0570(1) Å, α = 76.285(1)°, β = 82.198(2)°, γ = 87.075(1)°, Z = 1. The crystal structure of (I) can be described by infinite polyanions [(HAsO4)2Mo6O18]4- organized with water molecules in layers parallel to the c-direction; adjacent layers are further joined up by hydrogen bonding interactions with organic groups which were associated in chains spreading along the b-direction. The structure of (II) consists of functionalized selenomolybdate clusters [SeMo6O21(CH3COO)3]5-, protonated imidazole cations, sodium ions and lattice water molecules, which are held together to generate a three-dimensional supramolecular network via hydrogen-bonding interaction. Furthermore, the electrochemical properties of these compounds have been studied.

Inactivation of Escherichia coli O157:H7 and Salmonella typhimurium DT 104 on alfalfa seeds by levulinic acid and sodium dodecyl sulfate.

PubMed

Zhao, Tong; Zhao, Ping; Doyle, Michael P

2010-11-01

Studies were conducted to determine the best concentration and exposure time for treatment of alfalfa seeds with levulinic acid plus sodium dodecyl sulfate (SDS) to inactivate Escherichia coli O157:H7 and Salmonella without adversely affecting seed germination. Alfalfa seeds inoculated with a five-strain mixture of E. coli O157:H7 or Salmonella Typhimurium were dried in a laminar flow hood at 21°C for up to 72 h. Inoculated alfalfa seeds dried for 4 h then treated for 5 min at 21°C with 0.5% levulinic acid and 0.05% SDS reduced the population of E. coli O157:H7 and Salmonella Typhimurium by 5.6 and 6.4 log CFU/g, respectively. On seeds dried for 72 h, treatment with 0.5% levulinic acid and 0.05% SDS for 20 min at 21°C reduced E. coli O157:H7 and Salmonella Typhimurium populations by 4 log CFU/g. Germination rates of alfalfa seeds treated with 0.5% levulinic acid plus 0.05% SDS for up to 1 h at 21°C were compared with a treatment of 20,000 ppm of calcium hypochlorite or tap water only. Treatment of alfalfa seeds with 0.5% levulinic acid plus 0.05% SDS for 5 min at 21°C resulted in a >3.0-log inactivation of E. coli O157:H7 and Salmonella.

Fluid inclusion, rare earth element geochemistry, and isotopic characteristics of the eastern ore zone of the Baiyangping polymetallic Ore district, northwestern Yunnan Province, China

NASA Astrophysics Data System (ADS)

Feng, Caixia; Bi, Xianwu; Liu, Shen; Hu, Ruizhong

2014-05-01

The Baiyangping Cu-Ag polymetallic ore district is located in the northern part of the Lanping-Simao foreland fold belt, which lies between the Jinshajiang-Ailaoshan and Lancangjiang faults in western Yunnan Province, China. The source of ore-forming fluids and materials within the eastern ore zone were investigated using fluid inclusion, rare earth element (REE), and isotopic (C, O, and S) analyses undertaken on sulfides, gangue minerals, wall rocks, and ores formed during the hydrothermal stage of mineralization. These analyses indicate: (1) The presence of five types of fluid inclusion, which contain various combinations of liquid (l) and vapor (v) phases at room temperature: (a) H2O (l), (b) H2O (l) + H2O (v), (c) H2O (v), (d) CmHn (v), and (e) H2O (l) + CO2 (l), sometimes with CO2 (v). These inclusions have salinities of 1.4-19.9 wt.% NaCl equivalents, with two modes at approximately 5-10 and 16-21 wt.% NaCl equivalent, and homogenization temperatures between 101 °C and 295 °C. Five components were identified in fluid inclusions using Raman microspectrometry: H2O, dolomite, calcite, CH4, and N2. (2) Calcite, dolomitized limestone, and dolomite contain total REE concentrations of 3.10-38.93 ppm, whereas wall rocks and ores contain REE concentrations of 1.21-196 ppm. Dolomitized limestone, dolomite, wall rock, and ore samples have similar chondrite-normalized REE patterns, with ores in the Huachangshan, Xiaquwu, and Dongzhiyan ore blocks having large negative δCe and δEu anomalies, which may be indicative of a change in redox conditions during fluid ascent, migration, and/or cooling. (3) δ34S values for sphalerite, galena, pyrite, and tetrahedrite sulfide samples range from -7.3‰ to 2.1‰, a wide range that indicates multiple sulfur sources. The basin contains numerous sources of S, and deriving S from a mixture of these sources could have yielded these near-zero values, either by mixing of S from different sources, or by changes in the geological conditions of seawater sulfate reduction to sulfur. (4) The C-O isotopic analyses yield δ13C values from ca. zero to -10‰, and a wider range of δ18O values from ca. +6 to +24‰, suggestive of mixing between mantle-derived magma and marine carbonate sources during the evolution of ore-forming fluids, although potential contributions from organic carbon and basinal brine sources should also be considered. These data indicate that ore-forming fluids were derived from a mixture of organism, basinal brine, and mantle-derived magma sources, and as such, the eastern ore zone of the Baiyangping polymetallic ore deposit should be classified as a “Lanping-type” ore deposit.

Survival of Escherichia coli O157:H7 during manufacture and storage of white brined cheese.

PubMed

Osaili, Tareq M; Al-Nabulsi, Anas A; Olaimat, Amin N; Shaker, Reyad R; Taha, Mohammad; Holley, Richard A

2014-09-01

Escherichia coli O157:H7 is a major foodborne pathogen that causes severe disease in humans. Survival of E. coli O157:H7 during processing and storage of white brined cheese was investigated. Cheeses were prepared using pasteurized milk inoculated with a 4 strain E. coli O157:H7 cocktail (7 log(10) CFU/g) with or without yogurt starter culture (Lactobacillus delbrueckii ssp. bulgaricus and Streptococcus salivarius ssp. thermophilus) and stored in 10% or 15% NaCl brine at 10 and 21 ºC for 28 d. NaCl concentration, water activity (a(w)), pH, and numbers of E. coli O157:H7 and lactic acid bacteria (LAB) were determined in cheese and brine. E. coli O157:H7 was able to survive in cheese stored in both brines at 10 and 21 ºC regardless of the presence of starter LAB, although the latter significantly enhanced E. coli O157:H7 reduction in cheese or its brine at 10 ºC. E. coli O157:H7 numbers were reduced by 2.6 and 3.4 log(10) CFU/g in cheese stored in 10% and 15% NaCl brine, respectively, in the presence of starter LAB and by 1.4 and 2.3 log(10) CFU/g, respectively, in the absence of starter LAB at 10 ºC. The pathogen survived, but at lower numbers in the brines. The salt concentration of cheese stored in 10% brine remained about 5% during ripening, but in 15% brine, the NaCl level increased 1.6% to 8.1% (w/w) by 28 d. Values of pH and a(w) slightly decreased 1 d after exposure to brine and reached 5.5 to 6.6 and 0.88 to 0.94, respectively, in all treatments. © 2014 Institute of Food Technologists®

Sol-gel synthesis of K{sub 3}InF{sub 6} and structural characterization of K{sub 2}InC{sub 10}O{sub 10}H{sub 6}F{sub 9}, K{sub 3}InC{sub 12}O{sub 14}H{sub 4}F{sub 18} and K{sub 3}InC{sub 12}O{sub 12}F{sub 18}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Labeguerie, Jessica; Gredin, Patrick; Marrot, Jerome

2005-10-15

K{sub 3}InF{sub 6} is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K{sub 2}InC{sub 10}O{sub 10}H{sub 6}F{sub 9}, K{sub 3}InC{sub 12}O{sub 14}H{sub 4}F{sub 18} and K{sub 3}InC{sub 12}O{sub 12}F{sub 18}. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. Themore » two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K{sub 3}InF{sub 6} by decomposition at high temperature. The crystal structure of K{sub 3}InC{sub 12}O{sub 14}H{sub 4}F{sub 18} is characterized by complex anions [In(CF{sub 3}COO){sub 4}(OH{sub x}){sub 2}]{sup (5-2x)-} and isolated [CF{sub 3}COOH{sub 2-x}]{sup (x-1)-} molecules with x=2 or 1, surrounded by K{sup +} cations. The crystal structure of K{sub 3}InC{sub 12}O{sub 12}F{sub 18} is only constituted by complex anions [In(CF{sub 3}COO){sub 6}]{sup 3-} and K{sup +} cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K{sub 2}InC{sub 10}O{sub 10}H{sub 6}F{sub 9} and K{sub 3}InC{sub 12}O{sub 12}F{sub 18} were also performed at room temperature on pulverized crystals.« less

Thermodynamic analysis of reaction equilibria in ionic and molecular liquid systems by high-temperature Raman spectroscopy.

PubMed

Kalampounias, Angelos G; Boghosian, Soghomon

2009-09-01

A formalism for correlating relative Raman band intensities with the stoichiometric coefficients, the equilibrium constant, and the thermodynamics of reaction equilibria in solution is derived. The proposed method is used for studying: (1) the thermal dissociation of molten KHSO(4) in the temperature range 240-450 degrees C; (2) the dinuclear complex formation in molten TaCl(5)-AlCl(3) mixtures at temperatures between 125 and 235 degrees C. The experimental and calculational procedures for exploiting the temperature-dependent Raman band intensities in the molten phase as well as (if applicable) in the vapors thereof are described and used for determining the enthalpy of the equilibria: (1) 2HSO(4)(-)(l) <--> S(2)O(7)(2-)(l) + H(2)O(g), DeltaH(0)=64.9 +/- 2.9 kJ mol(-1); and (2) 1/2Ta(2)Cl(10)(l) + 1/2Al(2)Cl(6)(l) <--> TaAlCl(8)(l), DeltaH(0)=-12.1 +/- 1.5 kJ mol(-1).

Kinetics of Reduction of CaO-FeO x -MgO-PbO-SiO2 Slags by CO-CO2 Gas Mixtures

NASA Astrophysics Data System (ADS)

Jahanshahi, Sharif; Wright, Steven

2017-08-01

Kinetics of the reaction of lead slags (PbO-CaO-SiO2-FeO x -MgO) with CO-CO2 gas mixtures was studied by monitoring the changes in the slag composition when a stream of CO-CO2 gas mixture was blown on the surface of thin layers of slags (3 to 10 mm) at temperatures in the range of 1453 K to 1593 K (1180 °C to 1320 °C). These measurements were carried out under conditions where mass transfer in the gas phase was not the rate-limiting step and the reduction rates were insensitive to factors affecting mass transfer in the slag phase. The results show simultaneous reduction of PbO and Fe2O3 in the slag. The measured specific rate of oxygen removal from the melts varied from about 1 × 10-6 to 4 × 10-5 mol O cm-2 s-1 and was strongly dependent on the slag chemistry and its oxidation state, partial pressure of CO in the reaction gas mixture, and temperature. The deduced apparent first-order rate constant increased with increasing iron oxide content, oxidation state of the slag, and temperature. The results indicate that under the employed experimental conditions, the rate of formation of CO2 at the gas-slag interface is likely to be the rate-limiting step.

Sulfated and pyruvylated disaccharide alditols obtained from a red seaweed galactan: ESIMS and NMR approaches.

PubMed

Gonçalves, Alan G; Ducatti, Diogo R B; Duarte, M Eugênia R; Noseda, Miguel D

2002-11-29

The water-soluble acid agaran isolated from Acanthophora spicifera (Rhodophyta) was submitted to alkaline treatment for the complete cyclization of alpha-L-Galp 6-sulfate to 3,6-An-alpha-L-Galp units. The modified agaran was then partially depolymerized using partial reductive hydrolysis. The resulting oligosaccharide mixture was fractionated by adsorption and ion-exchange chromatography. Fractions were purified by gel-filtration chromatography and studied by ESIMS and NMR spectroscopy, including 1D 1H, 13C, DEPT and 2D 1H, 1H COSY, TOCSY and 1H, 13C HMQC procedures. The following neutral, pyruvylated, sulfated and sulfated/pyruvylated disaccharide alditols were obtained: beta-D-Galp-(1-->4)-3,6-An-L-GalOH; 4,6-O-(1-carboxyethylidene)-beta-D-Galp-(1-->4)-3,6-An-L-GalOH; beta-D-Galp 2-sulfate-(1-->4)-3,6-An-L-GalOH and 4,6-O-(1-carboxyethylidene)-beta-D-Galp 2-sulfate-(1-->4)-3,6-An-L-GalOH.

Studies on mass energy-absorption coefficients and effective atomic energy-absorption cross sections for carbohydrates

NASA Astrophysics Data System (ADS)

Ladhaf, Bibifatima M.; Pawar, Pravina P.

2015-04-01

We measured here the mass attenuation coefficients (μ/ρ) of carbohydrates, Esculine (C15H16O9), Sucrose (C12H22O11), Sorbitol (C6H14O6), D-Galactose (C6H12O6), Inositol (C6H12O6), D-Xylose (C5H10O5) covering the energy range from 122 keV up to 1330 keV photon energies by using gamma ray transmission method in a narrow beam good geometry set-up. The gamma-rays were detected using NaI(Tl) scintillation detection system with a resolution of 8.2% at 662 keV. The attenuation coefficient data were then used to obtain the total attenuation cross-section (σtot), molar extinction coefficients (ε), mass-energy absorption coefficients (μen/ρ) and effective (average) atomic energy-absorption cross section (σa,en) of the compounds. These values are found to be in good agreement with the theoretical values calculated based on XCOM data.

Kinetic Studies of the Thermal Decomposition of Methylperoxynitrate and of Ozone-Olefin Reactions.

NASA Astrophysics Data System (ADS)

Bahta, Abraha

This research concerns the thermal decomposition kinetics of CH(,3)O(,2)NO(,2) and laboratory kinetic measurements of ozone-olefin reactions. In the first system, the thermal decomposition rate of CH(,3)O(,2)NO(,2) was studied in the temperature range of 256-268 K at (TURN)350 torr total pressure and in the pressure range of 50-720 torr at 263 K by the perturbation of the equilibrium: (UNFORMATTED TABLE FOLLOWS). CH(,3)O(,2) + NO(,2) (+M) (DBLARR) CH(,3)O(,2)NO(,2) (+M) (3,-3). with NO. CH(,3)O(,2) + NO (--->) CH(,3)O + NO(,2) (4). (TABLE ENDS). The CH(,3)O(,2)NO(,2) was generated in situ by the photolysis of Cl(,2) in the presence of O(,2), CH(,4) and NO(,2). The decomposition kinetics were monitored in the presence of NO by the change in ultraviolet absorption at 250 nm. The Arrhenius expression obtained for the thermal decomposition is k(,-3) = 6 x 10('15) exp{-(21,000 (+OR-) 1500)/RT} sec('-1) at (TURNEQ)350 torr total pressure (mostly CH(,4)) where R = 1.987 cal/mole('-) K. The uncertainty in the Arrhenius parameters can be greatly reduced by combining this expression with data for k(,3) and thermodynamics data to give k(,-3) = (6 (+OR-) 3) x 10('15) exp{-(21,300 (+OR-) 300)/RT} sec('-1) at (TURNEQ)350 torr total pressure. Computations based on the pressure dependence of the forward reaction give k(,-3)('(INFIN)) = 2.1 x 10('16) exp{-(21,700 (+OR -) 300)/RT} sec('-1) k(,-3)('(DEGREES)) = 3.3 x 10(' -4) exp{-(20,150 x 300)/RT} cm('3) sec('-1). At 263 K the equilibrium constant K(,3,-3){263 K} is determined to be (2.68 (+OR-) 0.26) x 10('-10) cm('3). In the stratosphere the CH(,3)O(,2)NO(,2) lifetime will be controlled by play a role in the NO(,x) budget of the lower stratosphere. In the second part, the kinetics of the reactions of O(,3) with C(,2)H(,4), C(,3)H(,4), 1,3-C(,4)H(,6), and trans-1,3-C(,5)H(,8) were studied with initial olefin-to -ozone ratios (GREATERTHEQ) 4.9, in the presence of excess O(,2), and over the temperature range 232 to 300 K. The initial O(,3) pressure was varied from 5-18 mtorr, and the olefin pressure was varied from 0.1 to 4.5 torr (C(,2)H(,4)), 2.8 to 39.6 torr (allene), 52.7 to 600 mtorr (1,3-C(,4)H(,6)), or 26.2 to 106 mtorr (1,3-C(,5)H(,8)). The O(,3) decay was monitored by ultraviolet absorption. The reaction is first order in both O(,3) and olefin. The rate coefficients are independent of the O(,2) pressure (100-400 torr), and in the case of the O(,3)/C(,2)H(,4) system, the rate coefficients are independent of the nature of the diluent gas--N(,2), O(,2), and air were used. These measured rate coefficients were found to fit the Arrhenius expressions: (UNFORMATTED TABLE FOLLOWS). For C(,2)H(,4): k{232-298 K}=(7.88(+OR -)0.46)x10('-15) exp{-(5085(+OR-)580)/RT}. For C(,3)H(,4): k{252-298 K}=(1.92(+OR -)0.14)x10('-15) exp{-(5430(+OR-)830)/RT}. For 1,3-C(,4)H(,6): k{254-299 K}=(2.43(+OR -)0.15)x10('-14) exp{-(4900(+OR-)670)}. and. For t-1,3-C(,5)H(,8): k{262-298 K}=(6.56(+OR -)0.40)x10('-12). exp{-(7140(+OR-)860)/RT}. (TABLE ENDS). cm('3) s('-1), where the uncertainties represent one standard deviation.

Basic molten salt process-A new route for synthesis of nanocrystalline Li 4Ti 5O 12-TiO 2 anode material for Li-ion batteries using eutectic mixture of LiNO 3-LiOH-Li 2O 2

NASA Astrophysics Data System (ADS)

Rahman, M. M.; Wang, Jia-Zhao; Hassan, Mohd Faiz; Chou, Shulei; Wexler, David; Liu, Hua-Kun

A nanocrystalline Li 4Ti 5O 12-TiO 2 duplex phase has been synthesized by a simple basic molten salt process (BMSP) using an eutectic mixture of LiNO 3-LiOH-Li 2O 2 at 400-500 °C. The microstructure and morphology of the Li 4Ti 5O 12-TiO 2 product are characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The sample prepared by heat-treating at 300 °C for 3 h (S-1) reveals dense agglomerates of ultra-fine nanocrystalline Li 4Ti 5O 12; with heat treatment at 400 °C for 3 h (S-2), there is a duplex crystallite size (fine < 10 nm, and coarse > 20 nm) of Li 4Ti 5O 12-TiO 2; at 500 °C for 3 h (S-3), a much coarser and less-dense distribution of lithium titanate (crystallite size ∼15-30 nm) is observed. According to the results of electrochemical testing, the S-2 sample shows initial discharge capacities of 193 mAh g -1 at 0.2 C, 168 mAh g -1 at 0.5 C, 146 mAh g -1 at 1 C, 135 mAh g -1 at 2 C, and 117 mAh g -1 at 5 C. After 100 cycles, the discharge capacity is 138 mAh g -1 at 1 C with a capacity retention of 95%. The S-2 sample yields the best electrochemical performance in terms of charge-discharge capacity and rate capability compared with other samples. Its superior electrochemical performance can be mainly attributed to the duplex crystallite structure, composed of fine (<10 nm) and coarse (>20) nm nanoparticles, where lithium ions can be stored within the grain boundary interfaces between the spinel Li 4Ti 5O 12 and the anatase TiO 2.

Water clusters adsorbed on polycyclic aromatic hydrocarbons: Energetics and conformational dynamics

NASA Astrophysics Data System (ADS)

Simon, Aude; Spiegelman, Fernand

2013-05-01

In this work, we present some classical molecular dynamics (MD) simulations and finite temperature infrared (IR) spectra of water clusters adsorbed on coronene (C24H12), a compact polycyclic aromatic hydrocarbon (PAH). The potential energy surface is obtained within the self-consistent-charge density-functional based tight-binding approach with modifications insuring the correct description of water-water and water-PAH interactions. This scheme is benchmarked for the minimal energy structures of (C24H12)(H2O)n (n = 3-10) against density-functional theory (DFT) calculations and for the low-energy isomers of (H2O)6 and (C6H6)(H2O)3 against correlated wavefunction and DFT calculations. A detailed study of the low energy isomers of (C24H12)(H2O)3, 6 complexes is then provided. On-the-fly Born-Oppenheimer MD simulations are performed in the temperature T range 10-350 K for (C24H12)(H2O)n (n = 3-7) complexes. The description of the evolution of the systems with T is provided with emphasis on (C24H12)(H2O)n (n = 3,6). For T in the range 50-150 K, isomerisation processes are observed and when T increases, a solid-to-liquid phase-change like behavior is shown. The desorption of one water molecule is frequently observed at 300 K. The isomerisation processes are evidenced on the finite temperature IR spectra and the results are presented for (C24H12)(H2O)n (n = 3,6). A signature for the edge-coordination of the water cluster on the PAH is also proposed.

Corrosion of 310 stainless steel in H2-H2O-H2S gas mixtures: Studies at constant temperature and fixed oxygen potential

NASA Technical Reports Server (NTRS)

Rao, D. B.; Jacob, K. T.; Nelson, H. G.

1981-01-01

Corrosion of SAE 310 stainless steel in H2-H2O-H2S gas mixtures was studied at a constant temperature of 1150 K. Reactive gas mixtures were chosen to yield a constant oxygen potential of approximately 6 x 10 to the minus 13th power/cu Nm and sulfur potentials ranging from 0.19 x 10 to the minus 2nd power/cu Nm to 33 x 10 to the minus 2nd power/cu Nm. The kinetics of corrosion were determined using a thermobalance, and the scales were analyzed using metallography, scanning electron microscopy, and energy dispersive X-ray analysis. Two corrosion regimes, which were dependent on sulfur potential, were identified. At high sulfur potentials (p sub S sub 2 less than or equal to 2.7 x 10 to the minus 2nd power/cu Nm) the corrosion rates were high, the kinetics obeyed a linear rate equation, and the scales consisted mainly of sulfide phases similar to those observed from pure sulfication. At low sulfur potentials (P sub S sub 2 less than or equal to 0.19 x 10 to the minus 2nd power/cu Nm) the corrosion rates were low, the kinetics obeyed a parabolic rate equation, and scales consisted mainly of oxide phases.

Densities and viscosities of solutions of monoethanolamine + N-Methyldiethanolamine + water and monoethanolamine + 2-amino-2-methyl-1-propanol + water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, M.H.; Lie, Y.C.

1994-07-01

The densities and viscosities of aqueous mixtures of monoethanolamine (MEA) with N-methyldiethanolamine (MDEA) and MEA with 2-amino-2-methyl-1-propanol (AMP) have been studied at temperatures from 30 to 80 C. For density measurements, four MEA + MDEA (a total of 20 mass %) + H[sub 2]O mixtures and eight MEA + AMP (20 and 30 mass %) + H[sub 2]O mixtures were studied. For viscosity measurements, ten MEA + MDEA + H[sub 2]O mixtures and eight MEA + AMP + H[sub 2]O mixtures were measured. A Redlich-Kister equation of the excess volume was applied to represent the density of the liquid mixtures.more » The equation of Grunberg and Nissan of liquid viscosity was used to correlate the viscosity data. Both density and viscosity calculations show satisfactory results.« less

Hydrothermal synthesis of zeolite T from kaolin using two different structure-directing agents

NASA Astrophysics Data System (ADS)

Arshad, Sazmal E.; Lutfor Rahman, M.; Sarkar, Shaheen M.; Yusslee, Eddy F.; Patuwan, Siti Z.

2018-01-01

Zeolite T was synthesized from the molar chemical composition of 1SiO2:0.04Al2O3:0.26Na2O:0.09K2O:14H2O in the form of a homogenous milky solution in the presence of the two different structure-directing agents TMAOH and TEAOH respectively. Modification of the composition of silica was undertaken using metakaolin from calcined kaolin at 750 °C for 4 h, while the molar composition of each different SDA was variated from 0.05, 0.10, 0.15, 0.20 and 0.25. The homogenous mixture was left at room temperature for 24 h before undergoing hydrothermal synthesis at 100 °C for 168 h. The synthesized samples were filtered and aged at 120 °C for 2 h and each sample was calcined at high temperatures (545 °C for TMAOH and 520 °C for TEAOH) for template removal before characterization using XRD and SEM. Crystallization of the zeolite T in its major form only took place at a molar ratio of 0.10 of TMAOH, while TEAOH showed the species evolution of zeolite T into zeolite L and W for other molar ratios.

Use of model super-shedders to define the role of pen floor and hide contamination in the transmission of Escherichia coli O157:H7.

PubMed

Stanford, K; Stephens, T P; McAllister, T A

2011-01-01

Super-shedders, cattle shedding at least 10(4) cfu of Escherichia coli O157:H7 per gram of feces, increase the risks of contaminating the food chain and disseminating the organism through cattle populations. Because detecting super-shedders in cattle populations is laborious and time-consuming, a study was conducted to evaluate the role of hide and pen-floor contamination by model super shedders (MSS) in transmission of E. coli O157:H7. Steers (n = 48) negative for E. coli O157:H7 were allocated to 6 pens, with 2 replicate pens per treatment. Treatment A consisted of 3,000 g of feces inoculated with 10(6) cfu/g of a 5-strain mixture of nalidixic acid-resistant E. coli O157:H7 and spread in simulated fecal pats on the pen floor for d 0 through 4 and d 14 through 18. For treatment B, 100 g of the feces per day was spread on the perineum of 1 MSS per pen, and the remaining feces was placed on the pen floor as fecal pats similar to treatment A. Treatment C differed from B in that 50 g of feces was spread on the perineum and 50 g on the brisket of the MSS steer. Fecal samples, perineal swabs (500-cm(2) area around the anus), freshly voided fecal pats and manila rope samples were collected during a 56-d experimental period. More positive rope samples were found in treatments B and C compared with A (P = 0.05), and steers within treatments B and C were 1.3 times more likely (P = 0.05) to shed E. coli O157:H7 in their feces than steers in treatment A. Even though the number of E. coli O157:H7 introduced into pens was similar, results indicate an increased importance of hide compared with pen-floor contamination for transmission of this organism to cattle. Because cattle within treatment B were persistently colonized with E. coli O157:H7, this design should prove suitable for future studies investigating the role of super-shedders in the transmission of E. coli O157:H7.

Competitive reactions among glutathione, cisplatin and copper-phenanthroline complexes.

PubMed

Cadoni, Enzo; Valletta, Elisa; Caddeo, Graziano; Isaia, Francesco; Cabiddu, Maria Grazia; Vascellari, Sarah; Pivetta, Tiziana

2017-08-01

A large number of cancers are treated with cisplatin (CDDP). However, its use is limited by drug resistance, which is often related to intracellular levels of thiol-containing molecules such as glutathione (GSH). The role of GSH in cisplatin-resistant cancer cells is still unclear. GSH may form adducts with CDDP which results in the deactivation of the drug, and, actually, a high intracellular level of GSH was observed in some cisplatin-resistant cancers. To overcome drug resistance, CDDP is often administered in combination with one or more drugs to exploit a possible synergistic effect. In previous studies, we observed that the sensitivity to CDDP of leukemic and ovarian cisplatin-resistant cancer cells was restored in the presence of [Cu(phen) 2 (H 2 O)](ClO 4 ) 2 (C0) (phen is 1,10-phenathroline). In order to clarify the possible interactions between GSH and CDDP, the reactivity and competitive reactions among CDDP, C0 and GSH in binary and ternary mixtures were studied. The investigation was extended also to [Cu(phen)(H 2 O) 2 (ClO 4 ) 2 ] (C10) and GSSG, the oxidized form of GSH. It was observed that CDDP was able to react with the studied copper complexes and with GSH or GSSG. However, in mixtures containing CDDP, GSH or GSSG and C0 or C10, only copper-glutathione complexes were detected, while no platinum-glutathione adducts were found. Copyright © 2017 Elsevier Inc. All rights reserved.

Crystal Structures and Thermal Properties of Two Transition-Metal Compounds {[Ni(DNI)2(H2O)3][Ni(DNI)2 (H2O)4]}·6H2O and Pb(DNI)2(H2O)4 (DNI = 2,4-Dinitroimidazolate)

PubMed Central

Zhang, Guo-Fang; Cai, Mei-Yu; Jing, Ping; He, Chong; Li, Ping; Zhao, Feng-Qi; Li, Ji-Zhen; Fan, Xue-Zhong; Ng, Seik Weng

2010-01-01

Two transition-metal compounds derived from 2,4-dinitroimidazole, {[Ni(DNI)2(H2O)3][Ni(DNI)2 (H2O)4]}·6H2O, 1, and Pb(DNI)2(H2O)4, 2, were characterized by elemental analysis, FT-IR, TG-DSC and X-ray single-crystal diffraction analysis. Crystal data for 1: monoclinic, space group C2/c, a = 26.826(3), b = 7.7199(10), c = 18.579(2) Å, β = 111.241(2)° and Z = 4; 2: monoclinic, space group C2/c, a = 6.5347(6), b = 17.1727(17), c = 14.1011(14) Å, β = 97.7248(10) and Z = 4. Compound 1 contains two isolated nickel centers in its structure, one being six-coordinate and another five-coordinate. The structure of 2 contains a lead (II) center surrounded by two chelating DNI ligands and four water molecules in distorted square-antiprism geometry. The abundant hydrogen bonds in two compounds link the molecules into three-dimensional network and stabilize the molecules. The TG-DSC analysis reveals that the first step is the loss of water molecules and the final residue is the corresponding metal oxides and carbon. PMID:20526419

Mesoporous MnCeOx solid solutions for low temperature and selective oxidation of hydrocarbons

PubMed Central

Zhang, Pengfei; Lu, Hanfeng; Zhou, Ying; Zhang, Li; Wu, Zili; Yang, Shize; Shi, Hongliang; Zhu, Qiulian; Chen, Yinfei; Dai, Sheng

2015-01-01

The development of noble-metal-free heterogeneous catalysts that can realize the aerobic oxidation of C–H bonds at low temperature is a profound challenge in the catalysis community. Here we report the synthesis of a mesoporous Mn0.5Ce0.5Ox solid solution that is highly active for the selective oxidation of hydrocarbons under mild conditions (100–120 °C). Notably, the catalytic performance achieved in the oxidation of cyclohexane to cyclohexanone/cyclohexanol (100 °C, conversion: 17.7%) is superior to those by the state-of-art commercial catalysts (140–160 °C, conversion: 3-5%). The high activity can be attributed to the formation of a Mn0.5Ce0.5Ox solid solution with an ultrahigh manganese doping concentration in the CeO2 cubic fluorite lattice, leading to maximum active surface oxygens for the activation of C–H bonds and highly reducible Mn4+ ions for the rapid migration of oxygen vacancies from the bulk to the surface. PMID:26469151

Uranyl Ion Complexes with Long-Chain Aliphatic α,ω-Dicarboxylates and 3d-Block Metal Counterions.

PubMed

Thuéry, Pierre; Harrowfield, Jack

2016-03-07

Twelve new complexes were obtained from reaction of uranyl ions with the aliphatic dicarboxylic acids HOOC-(CH2)n-2-COOH (H2Cn; n = 7-10 and 12) under solvo-hydrothermal conditions, in the presence of 3d-block metal ions (Mn(2+), Fe(3+), Co(2+), Ni(2+), and Cu(2+)) and 2,2'-bipyridine (bipy) or 1,10-phenanthroline (phen). In contrast to previously reported triple-stranded helicates obtained with C9(2-) and C12(2-), all these complexes crystallize as polymeric one-dimensional (1D) or two-dimensional (2D) species. [Fe(bipy)3][(UO2)2(C7)3]·3H2O (1), [Cu(phen)2]2[(UO2)3(C7)4(H2O)2]·2H2O (2), and [Cu(bipy)2]2[(UO2)2(C9)3] (6), in which the 3d cation was reduced in situ, are 1D ladderlike polymers displaying tetra- or hexanuclear rings, of sufficient width to encompass two counterions in 2 and 6. The three complexes [Co(phen)3][(UO2)3(C8)3(O)]·H2O (3), [Ni(phen)3][(UO2)3(C8)3(O)]·H2O (4) and [Co(phen)3][(UO2)3(C9)3(O)]·H2O (5) contain bis(μ3-oxo)-bridged tetranuclear secondary building units, and they crystallize as deeply furrowed 2D assemblies. Depending on the nature of the counterion, C10(2-) gives [Ni(bipy)3][(UO2)2(C10)3]·2H2O (7), a 2D network displaying elongated decanuclear rings containing the counterions, or [Mn(phen)3][(UO2)2(C10)3]·6H2O (8), [Co(phen)3][(UO2)2(C10)3]·7H2O (9), and [Ni(phen)3][(UO2)2(C10)3]·7H2O (10), which consist of 2D assemblies with honeycomb topology; the hexanuclear rings in 8-10 are chairlike and occupied by one counterion and two uranyl groups from neighboring layers. Two complexes of the ligand with the longest chain, C12(2-), are reported. [UO2(C12)(bipy)] (11) is a neutral 1D species in which bipy chelates the uranyl ion and plays an important role in the packing through π-stacking interactions. Two polymeric units, 1D and 2D, coexist in the complex [Ni(bipy)3][(UO2)2(C12)3][UO2(C12)(H2O)2]·H2O (12); the 2D network has the honeycomb topology, but the hexanuclear rings are markedly convoluted, with local features akin to those in helicates, and the counterions are embedded in intralayer cavities. Emission spectra measured in the solid state show in most cases various degrees of quenching, with intense and well-resolved uranyl emission being observed only for complexes 2 and 11.

Short belt-like Ca 2 B 2 O 5 ·H 2 O nanostructures: Hydrothermal formation, FT-IR, thermal decomposition, and optical properties

NASA Astrophysics Data System (ADS)

Zhu, Wancheng; Zhang, Xiao; Wang, Xiaoli; Zhang, Heng; Zhang, Qiang; Xiang, Lan

2011-10-01

Uniform high crystallinity short belt-like Ca 2B 2O 5·H 2O nanostructures (nanobelts) were facilely synthesized through a room temperature coprecipitation of CaCl 2, H 3BO 3, and NaOH solutions, followed by a mild hydrothermal treatment (180 °C, 12.0 h). By a preferential growth parallel to the (1 0 0) planes, Ca 2B 2O 5·H 2O nanobelts with a length of 1-5 μm, a width of 100-400 nm, and a thickness of 55-90 nm were obtained. The calcination of the nanobelts at 500 °C for 2.0 h led to short Ca 2B 2O 5 nanobelts with well preserved 1D morphology. Calcination at 800 °C led to a mixture of Ca 2B 2O 5 and Ca 3B 2O 6. The products were with belt-like and quasi-polyhedron morphology, while they turned into pore-free micro-rod like and polyhedron morphology when the calcination was taken in the presence of NaCl. NaCl assisted high temperature calcination at 900 °C promoted the formation of Ca 3B 2O 6 in the products. When dispersed in deionized water or absolute ethanol, the Ca 2B 2O 5·H 2O nanobelts and Ca 2B 2O 5 nanobelts showed good transparency from the ultraviolet to the visible region. The as-synthesized Ca 2B 2O 5·H 2O and Ca 2B 2O 5 nanobelts can be employed as novel metal borate nanomaterials for further potential applications in the area of glass fibers, antiwear additive, ceramic coatings, and so on.

Tris(5,6-dimethyl-1H-benzimidazole-κN(3))(pyridine-2,6-dicarboxyl-ato-κ(3)O(2),N,O(6))nickel(II).

PubMed

Li, Yue-Hua; Li, Feng-Feng; Liu, Xin-Hua; Zhao, Ling-Yan

2012-06-01

The title mononuclear complex, [Ni(C(7)H(3)NO(4))(C(9)H(10)N(2))(3)], shows a central Ni(II) atom which is coordinated by two carboxyl-ate O atoms and the N atom from a pyridine-2,6-dicarboxyl-ate ligand and by three N atoms from different 5,6-dimethyl-1H--benzimidazole ligands in a distorted octa-hedral geometry. The crystal structure shows intermolecular N-H⋯O hydrogen bonds.

[Mechanism and performance of styrene oxidation by O3/H2O2].

PubMed

He, Jue-Cong; Huang, Qian-Ru; Ye, Qi-Hong; Luo, Yu-Wei; Zhang, Zai-Li; Fan, Qing-Juan; Wei, Zai-Shan

2013-10-01

It can produce a large number of free radicals in O3/H2O2, system, ozone and free radical coupling oxidation can improve the styrene removal efficiency. Styrene oxidation by O3/H2O2 was investigated. Ozone dosage, residence time, H2o2 volume fraction, spray density and molar ratio of O3/C8H8 on styrene removal were evaluated. The experimental results showed that styrene removal efficiency achieved 85.7%. The optimal residence time, H2O2, volume fraction, spray density and O3/C8H8 molar ratio were 20. 6 s, 10% , 1.72 m3.(m2.h)-1 and 0.46, respectively. The gas-phase degradation intermediate products were benzaldehyde(C6H5CHO) and benzoic acid (C6H5 COOH) , which were identified by means of gas chromatography-mass spectrometry(GC-MS). The degradation mechanism of styrene is presented.

Analysis of ferrite nanoparticles in the flow of ferromagnetic nanofluid

PubMed Central

Nadeem, Sohail; Mustafa, M. T.

2018-01-01

Theoretical analysis has been carried out to establish the heat transport phenomenon of six different ferromagnetic MnZnFe2O4—C2H6O2 (manganese zinc ferrite-ethylene glycol), NiZnFe2O4—C2H6O2 (Nickel zinc ferrite-ethylene glycol), Fe2O4—C2H6O2 (magnetite ferrite-ethylene glycol), NiZnFe2O4—H2O (Nickel zinc ferrite-water), MnZnFe2O4—H2O (manganese zinc ferrite-water), and Fe2O4—H2O (magnetite ferrite-water) nanofluids containing manganese zinc ferrite, Nickel zinc ferrite, and magnetite ferrite nanoparticles dispersed in a base fluid of ethylene glycol and water mixture. The performance of convective heat transfer is elevated in boundary layer flow region via nanoparticles. Magnetic dipole in presence of ferrites nanoparticles plays a vital role in controlling the thermal and momentum boundary layers. In perspective of this, the impacts of magnetic dipole on the nano boundary layer, steady, and laminar flow of incompressible ferromagnetic nanofluids are analyzed in the present study. Flow is caused by linear stretching of the surface. Fourier’s law of heat conduction is used in the evaluation of heat flux. Impacts of emerging parameters on the magneto—thermomechanical coupling are analyzed numerically. Further, it is evident that Newtonian heating has increasing behavior on the rate of heat transfer in the boundary layer. Comparison with available results for specific cases show an excellent agreement. PMID:29320488

Experimental studies on cycling stable characteristics of inorganic phase change material CaCl2·6H2O-MgCl2·6H2O modified with SrCl2·6H2O and CMC

NASA Astrophysics Data System (ADS)

He, Meizhi; Yang, Luwei; Zhang, Zhentao

2018-01-01

By means of mass ratio method, binary eutectic hydrated salts inorganic phase change thermal energy storage system CaCl2·6H2O-20wt% MgCl2·6H2O was prepared, and through adding nucleating agent 1wt% SrCl2·6H2O and thickening agent 0.5wt% carboxy methyl cellulose (CMC), inoganic phase change material (PCM) modified was obtained. With recording cooling-melting curves simultaneously, this PCM was frozen and melted for 100 cycles under programmable temperature control. After per 10 cycles, the PCM was charaterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD) and density meter, then analysing variation characteristics of phase change temperature, supercooling degree, superheat degree, latent heat, crystal structure and density with the increase of cycle index. The results showed that the average values of average phase change temperature for cooling and heating process were 25.70°C and 27.39°C respectively with small changes. The average values of average supercooling and superheat degree were 0.59°C and 0.49°C respectively, and the maximum value was 1.10°C. The average value and standard deviation of latent heat of fusion were 120.62 J/g and 1.90 J/g respectively. Non-molten white solid sediments resulted from phase separation were tachyhydrite (CaMg2Cl6·12H2O), which was characterized by XRD. Measuring density of the PCM after per 10 cycles, and the results suggested that the total mass of tachyhydrite was limited. In summary, such modified inoganic PCM CaCl2·6H2O-20wt% MgCl2·6H2O-1wt% SrCl2·6H2O-0.5wt% CMC could stay excellent circulation stability within 100 cycles, and providing reference value in practical use.

Storage and recovery of methane-ethane mixtures in single shale pores

NASA Astrophysics Data System (ADS)

Wu, Haiyi; Qiao, Rui

2017-11-01

Natural gas production from shale formations has received extensive attention recently. While great progress has been made in understanding the adsorption and transport of single-component gas inside shales' nanopores, the adsorption and transport of multicomponent shale gas under reservoir conditions (CH4 and C2H6 mixture) has only begun to be studied. In this work, we use molecular simulations to compute the storage of CH4 and C2H6 mixtures in single nanopores and their subsequent recovery. We show that surface adsorption contributes greatly to the storage of CH4 and C2H6 inside the pores and C2H6 is enriched over CH4. The enrichment of C2H6 is enhanced as the pore is narrowed, but is weakened as the pressure increases. We show that the recovery of gas mixtures from the nanopores approximately follows the diffusive scaling law. The ratio of the production rates of C2H6 and CH4 is close to their initial mole ratio inside the pore despite that the mobility of pure C2H6 is much smaller than that of pure CH4 inside the pores. By using scale analysis, we show that the strong coupling between the transport of CH4 and C2H6 is responsible for the effective recovery of C2H6 from the nanopores.

Ceo2 Based Catalysts for the Treatment of Propylene in Motorcycle’s Exhaust Gases

PubMed Central

Pham, Phuong Thi Mai; Le Minh, Thang; Nguyen, Tien The; Van Driessche, Isabel

2014-01-01

In this work, the catalytic activities of several single metallic oxides were studied for the treatment of propylene, a component in motorcycles’ exhaust gases, under oxygen deficient conditions. Amongst them, CeO2 is one of the materials that exhibit the highest activity for the oxidation of C3H6. Therefore, several mixtures of CeO2 with other oxides (SnO2, ZrO2, Co3O4) were tested to investigate the changes in catalytic activity (both propylene conversion and CO2 selectivity). Ce0.9Zr0.1O2, Ce0.8Zr0.2O2 solid solutions and the mixtures of CeO2 and Co3O4 was shown to exhibit the highest propylene conversion and CO2 selectivity. They also exhibited good activities when tested under oxygen sufficient and excess conditions and with the presence of co-existing gases (CO, H2O). PMID:28788253

Structures and interactions in N-methylacetamide-water mixtures studied by IR spectra and density functional theory

NASA Astrophysics Data System (ADS)

Zhang, Rong; Li, Haoran; Lei, Yi; Han, Shijun

2004-05-01

IR spectra have been performed to study the structures and interactions in N-methylacetamide and water mixtures. Because of the competitions of acceptor and donor of the strong hydrogen bonds, some interesting phenomena of red shifts and blue shifts are observed in νCO and νN-H. It is due to the blue-shifting C-H⋯O hydrogen bond, the νC-H blue shifts more obviously. Then some representative cluster structures are suggested and further investigated by density functional theory method. The changes in bond length and frequency shift of the structures give good reasons for the red shift and blue shift, which represents excellent agreement with the IR experiment. The investigations of IR spectra and DFT calculations reveal that the weak C-H⋯O interactions play different roles compared with the classical strong hydrogen bonds in the NMA-water mixtures.

Highly hydrothermally stable microporous silica membranes for hydrogen separation.

PubMed

Wei, Qi; Wang, Fei; Nie, Zuo-Ren; Song, Chun-Lin; Wang, Yan-Li; Li, Qun-Yan

2008-08-07

Fluorocarbon-modified silica membranes were deposited on gamma-Al2O3/alpha-Al2O3 supports by the sol-gel technique for hydrogen separation. The hydrophobic property, pore structure, gas transport and separation performance, and hydrothermal stability of the modified membranes were investigated. It is observed that the water contact angle increases from 27.2+/-1.5 degrees for the pure silica membranes to 115.0+/-1.2 degrees for the modified ones with a (trifluoropropyl)triethoxysilane (TFPTES)/tetraethyl orthosilicate (TEOS) molar ratio of 0.6. The modified membranes preserve a microporous structure with a micropore volume of 0.14 cm3/g and a pore size of approximately 0.5 nm. A single gas permeation of H2 and CO2 through the modified membranes presents small positive apparent thermal activation energies, indicating a dominant microporous membrane transport. At 200 degrees C, a single H2 permeance of 3.1x10(-6) mol m(-2) s(-1) Pa(-1) and a H2/CO2 permselectivity of 15.2 were obtained after proper correction for the support resistance and the contribution from the defects. In the gas mixture measurement, the H2 permeance and the H2/CO2 separation factor almost remain constant at 200 degrees C with a water vapor pressure of 1.2x10(4) Pa for at least 220 h, indicating that the modified membranes are hydrothermally stable, benefiting from the integrity of the microporous structure due to the fluorocarbon modification.

Efficient, environmentally acceptable method for waterproofing insulation material

NASA Technical Reports Server (NTRS)

Blohowiak, Kay Y. (Inventor); Krienke, Kenneth A. (Inventor); Olli, Larry K. (Inventor); Newquist, Charles W. (Inventor)

2000-01-01

A process of waterproofing alumina-rich or silica-rich fibrous thermal insulation material, the process including the steps of: (a) providing an alumina-rich or a silica-rich fibrous material; (b) providing a waterproofing solution including: (1) a carrier solvent selected from the group consisting of aliphatic alcohols having from 1C to 6C, water, and mixtures thereof; and (2) an alkoxysilane defined by the formula R.sub.4-x -Si-(O-R').sub.x where x is 1-3 and R is selected from the group consisting of alkyl groups having from 1C to 10C, hydrogen, or fluorocarbon groups having from 1F to 15F; and where O-R' is an alkoxy group having from 1C to 5C, or a mixture of alkoxysilanes defined by the above formula R.sub.4-x -Si-(O-R').sub.x ; and optionally (3) modifiers including acids, such as acetic acid or nitric acid, or bases, such as ammonium hydroxide, RNH.sub.2, R.sub.2 NH, or R.sub.3 N, or MOH, where R is selected from the group consisting of alkyl groups having from 1C to 10C or hydrogen, and where M=Na, Li, or K; (c) contacting the fibrous material with the waterproofing solution for a sufficient amount of time to waterproof the fibrous material; and (d) curing the coated fibrous material to render it sufficiently waterproof. A chemical solution for waterproofing alumina-rich or silica-rich fibrous thermal insulation materials, the solution including: (a) a carrier solvent selected from the group consisting of aliphatic alcohols having from 1C to 6C, water, and mixtures thereof; and (b) an alkoxysilane defined by the formula R.sub.4-x -Si-(O-R').sub.x where x is 1-3 and R is selected from the group consisting of alkyl groups having from 1C to 10C, hydrogen, or fluorocarbon groups having from 1F to 15F; and where O-R' is an alkoxy group having from 1C to 5C, or a mixture of alkoxysilanes defined by the above formula R.sub.4-x -Si-(O-R').sub.x ; and optionally (c) modifiers including acids, such as acetic acid or nitric acid, or bases, such as ammonium hydroxide, RNH.sub.2, R.sub.2 NH, or R.sub.3 N, or MOH, where R is selected from the group consisting of alkyl groups having from 1C to 10C or hydrogen, and where M=Na, Li, or K.

Improved Efficacy of Synthesizing *MIII-Labeled DOTA Complexes in Binary Mixtures of Water and Organic Solvents. A Combined Radio- and Physicochemical Study.

PubMed

Pérez-Malo, Marylaine; Szabó, Gergely; Eppard, Elisabeth; Vagner, Adrienn; Brücher, Ernő; Tóth, Imre; Maiocchi, Alessandro; Suh, Eul Hyun; Kovács, Zoltán; Baranyai, Zsolt; Rösch, Frank

2018-05-21

Typically, the synthesis of radiometal-based radiopharmaceuticals is performed in buffered aqueous solutions. We found that the presence of organic solvents like ethanol increased the radiolabeling yields of [ 68 Ga]Ga-DOTA (DOTA = 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacatic acid). In the present study, the effect of organic cosolvents [ethanol (EtOH), isopropyl alcohol, and acetonitrile] on the radiolabeling yields of the macrocyclic chelator DOTA with several trivalent radiometals (gallium-68, scandium-44, and lutetium-177) was systematically investigated. Various binary water (H 2 O)/organic solvent mixtures allowed the radiolabeling of DOTA at a significantly lower temperature than 95 °C, which is relevant for the labeling of sensitive biological molecules. Simultaneously, much lower amounts of the chelators were required. This strategy may have a fundamental impact on the formulation of trivalent radiometal-based radiopharmaceuticals. The equilibrium properties and formation kinetics of [M(DOTA)] - (M III = Ga III , Ce III , Eu III , Y III , and Lu III ) complexes were investigated in H 2 O/EtOH mixtures (up to 70 vol % EtOH). The protonation constants of DOTA were determined by pH potentiometry in H 2 O/EtOH mixtures (0-70 vol % EtOH, 0.15 M NaCl, 25 °C). The log K 1 H and log K 2 H values associated with protonation of the ring N atoms decreased with an increase of the EtOH content. The formation rates of [M(DOTA)] - complexes increase with an increase of the pH and [EtOH]. Complexation occurs through rapid formation of the diprotonated [M(H 2 DOTA)] + intermediates, which are in equilibrium with the kinetically active monoprotonated [M(HDOTA)] intermediates. The rate-controlling step is deprotonation (and rearrangement) of the monoprotonated intermediate, which occurs through H 2 O ( *M(HL) k H 2 O ) and OH - ( *M(HL) k OH ) assisted reaction pathways. The rate constants are essentially independent of the EtOH concentration, but the M(HL) k H2O values increase from Ce III to Lu III . However, the log K M(HL) H protonation constants, analogous to the log K H 2 value, decrease with increasing [EtOH], which increases the concentration of the monoprotonated M(HDOTA) intermediate and accelerates formation of the final complexes. The overall rates of complex formation calculated by the obtained rate constants at different EtOH concentrations show a trend similar to that of the complexation rates determined with the use of radioactive isotopes.

Plasma chemistry of NO in complex gas mixtures excited with a surfatron launcher.

PubMed

Hueso, J L; González-Elipe, A R; Cotrino, J; Caballero, A

2005-06-09

The plasma chemistry of NO has been investigated in gas mixtures with oxygen and/or hydrocarbon and Ar as carrier gas. Surface wave discharges operating at microwave frequencies have been used for this study. The different plasma reactions have been analyzed for a pressure range between 30 and 75 Torr. Differences in product concentration and/or reaction yields smaller than 10% were found as a function of this parameter. The following gas mixtures have been considered for investigation: Ar/NO, Ar/NO/O2, Ar/NO/CH4, Ar/CH4/O2, Ar/NO/CH4/O2. It is found that NO decomposes into N2 and O2, whereas other products such as CO, H2, and H2O are also formed when CH4 and O2 are present in the reaction mixture. Depending on the working conditions, other minority products such as HCN, CO2, and C2 or higher hydrocarbons have been also detected. The reaction of an Ar/NO plasma with deposits of solid carbon has also been studied. The experiments have provided useful information with respect to the possible removal of soot particles by this type of plasma. It has been shown that carbon deposits are progressively burned off by interaction with the plasma, and practically 100% decomposition of NO was found. Plasma intermediate species have been studied by optical emission spectroscopy (OES). Bands and/or peaks due to N2*, NO*, OH*, C2*, CN*, CH*, or H* were detected with different relative intensities depending on the gas mixture. From the analysis of both the reaction products and efficiency and the type of intermediate species detected by OES, different plasma reactions and processes are proposed to describe the plasma chemistry of NO in each particular mixture of gases. The results obtained provide interesting insights about the plasma removal of NO in real gas exhausts.

The dynamic behavior of a liquid ethanol-water mixture: a perspective from quantum chemical topology.

PubMed

Mejía, Sol M; Mills, Matthew J L; Shaik, Majeed S; Mondragon, Fanor; Popelier, Paul L A

2011-05-07

Quantum Chemical Topology (QCT) is used to reveal the dynamics of atom-atom interactions in a liquid. A molecular dynamics simulation was carried out on an ethanol-water liquid mixture at its azeotropic concentration (X(ethanol)=0.899), using high-rank multipolar electrostatics. A thousand (ethanol)(9)-water heterodecamers, respecting the water-ethanol ratio of the azeotropic mixture, were extracted from the simulation. Ab initio electron densities were computed at the B3LYP/6-31+G(d) level for these molecular clusters. A video shows the dynamical behavior of a pattern of bond critical points and atomic interaction lines, fluctuating over 1 ns. A bond critical point distribution revealed the fluctuating behavior of water and ethanol molecules in terms of O-H···O, C-H···O and H···H interactions. Interestingly, the water molecule formed one to six C-H···O and one to four O-H···O interactions as a proton acceptor. We found that the more localized a dynamical bond critical point distribution, the higher the average electron density at its bond critical points. The formation of multiple C-H···O interactions affected the shape of the oxygen basin of the water molecule, which is shown in three dimensions. The hydrogen atoms of water strongly preferred to form H···H interactions with ethanol's alkyl hydrogen atoms over its hydroxyl hydrogen. This journal is © the Owner Societies 2011

Carbonate mineral solubility at low temperatures in the Na-K-Mg-Ca-H-Cl-SO 4-OH-HCO 3-CO 3-CO 2-H 2O system

NASA Astrophysics Data System (ADS)

Marion, Giles M.

2001-06-01

Carbonate minerals have played an important role in the geochemical evolution of Earth, and may have also played an important role in the geochemical evolution of Mars and Europa. Several models have been published in recent years that describe chloride and sulfate mineral solubilities in concentrated brines using the Pitzer equations. Few of these models are parameterized for subzero temperatures, and those that are do not include carbonate chemistry. The objectives of this work are to estimate Pitzer-equation bicarbonate-carbonate parameters and carbonate mineral solubility products and to incorporate them into the FREZCHEM model to predict carbonate mineral solubilities in the Na-K-Mg-Ca-H-Cl-SO 4-OH-HCO 3-CO 3-CO 2-H 2O system at low temperatures (≤25°C) with a special focus on subzero temperatures. Most of the Pitzer-equation parameters and equilibrium constants are taken from the literature and extrapolated into the subzero temperature range. Solubility products for 14 sodium, potassium, magnesium, and calcium bicarbonate and carbonate minerals are included in the model. Most of the experimental data are at temperatures ≥ -8°C; only for the NaHCO 3-NaCl-H 2O and Na 2CO 3-NaCl-H 2O systems are there bicarbonate and carbonate data to temperatures as low as -21.6°C. In general, the fit of the model to the experimental data is good. For example, calculated eutectic temperatures and compositions for NaHCO 3, Na 2CO 3, and their mixtures with NaCl and Na 2SO 4 salts are in good agreement with experimental data to temperatures as low as -21.6°C. Application of the model to eight saline, alkaline carbonate waters give predicted pHs ranging from 9.2 to 10.2, in comparison with measured pHs that range from 8.7 to 10.2. The model suggests that the CaCO 3 mineral that precipitates during seawater freezing is probably calcite and not ikaite. The model demonstrates that a proposed salt assemblage for the icy surface of Europa consisting of highly hydrated MgSO 4 salts and natron (Na 2CO 3 · 10H 2O) is an incompatible salt assemblage.

Hydrogen-bonded supramolecular structures of three related 4-(5-nitro-2-furyl)-1,4-dihydropyridines.

PubMed

Quesada, Antonio; Argüello, Jacqueline; Squella, Juan A; Wardell, James L; Low, John N; Glidewell, Christopher

2006-01-01

In ethyl 5-cyano-2,6-dimethyl-4-(5-nitro-2-furyl)-1,4-dihydropyridine-3-carboxylate, C15H15N3O5, the molecules are linked into chains by a single N-H...O hydrogen bond. The molecules in diethyl 2,6-dimethyl-4-(5-nitro-2-furyl)-1,4-dihydropyridine-3,5-dicarboxylate, C17H20N2O7, are linked by a combination of one N-H...O hydrogen bond and two C-H...O hydrogen bonds into sheets built from equal numbers of R(2)(2)(17) and R(4)(4)(18) rings. In 2,6-dimethyl-4-(5-nitro-2-furyl)-1,4-dihydropyridine-3,5-dicarbonitrile, C13H10N4O3, the molecules are linked by a combination of a three-centre N-H...(O)2 hydrogen bond and two independent two-centre C-H...O hydrogen bonds into complex sheets containing four types of ring.

Inactivation of Escherichia coli O157:H7 and Listeria monocytogenes on plastic kitchen cutting boards by electrolyzed oxidizing water.

PubMed

Venkitanarayanan, K S; Ezeike, G O; Hung, Y C; Doyle, M P

1999-08-01

One milliliter of culture containing a five-strain mixture of Escherichia coli O157:H7 (approximately 10(10) CFU) was inoculated on a 100-cm2 area marked on unscarred cutting boards. Following inoculation, the boards were air-dried under a laminar flow hood for 1 h, immersed in 2 liters of electrolyzed oxidizing water or sterile deionized water at 23 degrees C or 35 degrees C for 10 or 20 min; 45 degrees C for 5 or 10 min; or 55 degrees C for 5 min. After each temperature-time combination, the surviving population of the pathogen on cutting boards and in soaking water was determined. Soaking of inoculated cutting boards in electrolyzed oxidizing water reduced E. coli O157:H7 populations by > or = 5.0 log CFU/100 cm2 on cutting boards. However, immersion of cutting boards in deionized water decreased the pathogen count only by 1.0 to 1.5 log CFU/100 cm2. Treatment of cutting boards inoculated with Listeria monocytogenes in electrolyzed oxidizing water at selected temperature-time combinations (23 degrees C for 20 min, 35 degrees C for 10 min, and 45 degrees C for 10 min) substantially reduced the populations of L. monocytogenes in comparison to the counts recovered from the boards immersed in deionized water. E. coli O157:H7 and L. monocytogenes were not detected in electrolyzed oxidizing water after soaking treatment, whereas the pathogens survived in the deionized water used for soaking the cutting boards. This study revealed that immersion of kitchen cutting boards in electrolyzed oxidizing water could be used as an effective method for inactivating foodborne pathogens on smooth, plastic cutting boards.

Interactions of methylamine and ammonia with atmospheric nucleation precursor H{sub 2}SO{sub 4} and common organic acids: Thermodynamics and atmospheric implications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Y.; Jiang, L.; Bai, Z.

Interactions of the two common atmospheric bases, ammonia (NH{sub 3}) and methylamine MA (CH{sub 3}NH{sub 2}), which are considered to be important stabilizers of binary clusters in the Earth’s atmosphere, with H{sub 2}SO{sub 4}, the key atmospheric precursor, and 14 common atmospheric organic acids (COA) (formic (CH{sub 2}O{sub 2}), acetic (C{sub 2}H{sub 4}O{sub 2}), oxalic (C{sub 2}H{sub 2}O{sub 4}), malonic (C{sub 3}H{sub 4}O{sub 4}), succinic (C{sub 4}H{sub 6}O{sub 4}), glutaric acid (C{sub 5}H{sub 8}O{sub 4}), adipic (C{sub 6}H{sub 10}O{sub 4}), benzoic (C{sub 6}H{sub 5}COOH), phenylacetic (C{sub 6}H{sub 5}CH{sub 2}COOH), pyruvic (C{sub 3}H{sub 4}O{sub 3}), maleic acid (C{sub 4}H{sub 4}O{sub 4}),more » malic (C{sub 4}H{sub 6}O{sub 5}), tartaric (C{sub 4}H{sub 6}O{sub 6}) and pinonic acid (C{sub 10}H{sub 16}O{sub 3})) have been studied using the composite high-accuracy G3MP2 method. The thermodynamic stability of mixed (COA) (H{sub 2}SO{sub 4}), (COA)(B1) and (COA)(B2) dimers and (COA) (H{sub 2}SO{sub 4}) (B1) and (COA) (H{sub 2}SO{sub 4}) (B1) trimers, where B1 and B2 represent methylamine (CH{sub 3}NH{sub 2}) and ammonia (NH{sub 3}), respectively, have been investigated and their impacts on the thermodynamic stability of clusters containing H{sub 2}SO{sub 4} have been analyzed. It has been shown that in many cases the interactions of H{sub 2}SO{sub 4} with COA, ammonia and methylamine lead to the formation of heteromolecular dimers and trimers, which are certainly more stable than (H{sub 2}SO{sub 4}){sub 2} and (H{sub 2}SO{sub 4}){sub 3}. It has also been found that free energies of (COA) (H{sub 2}SO{sub 4})+ CH{sub 3}NH{sub 2}⇔(COA) (H{sub 2}SO{sub 4})(CH{sub 3}NH{sub 2}) reactions exceed 10-15 kcal mol{sup −1}. This is a clear indication that mixed trimers composed of COA, H{sub 2}SO{sub 4} and methylamine are very stable and can thus serve as possible nucleation sites. The present study leads us to conclude that the interactions of COA coexisting with H{sub 2}SO{sub 4} and common atmospheric bases in the Earth’s atmosphere may be an important factor affecting the stability of nucleating sulfuric acid clusters and that the impacts of COA on atmospheric nucleation should be studied in further details.« less

Precipitation diagrams and solubility of uric acid dihydrate

NASA Astrophysics Data System (ADS)

Babić-Ivančić, V.; Füredi-Milhofer, H.; Brown, W. E.; Gregory, T. M.

1987-07-01

The solubility of uric acid dihydrate (UA·2H 2O) and the precipitation of UA·2H 2O and anhydrous uric acid (UA) from solutions containing sodium hydroxide and hydrochloric acid have been investigated. For the solubility studies, crystals of pure UA·2H 2O were prepared and equilibrated with water and with solutions of HCl or NaOH for 60 min or 20 h, respectively. The equilibrium pH (pH = 2-6.25) and uric acid concentration were determined. For the precipitation experiments, commercial UA was dissolved in NaOH in a 1:1.1 molar ratio and UA·2H 2O and/or UA were precipitated with hydrochloric acid. The precipitates and/or supernatants were examined 24 h after sample preparation. The results are represented in the form of tables, precipitation diagrams and "chemical potential" diagrams. Solubility measurements with 60 min equilibration times yielded the solubility products of UA·2H 2O, K sp(298 K) = (0.926 ± 0.025) × 10 -9mol2dm-6 and K sp(310 K) = (2.25 ± 0.05) × 10 -9mol2dm-6 and the first dissociation constants of uric acid, K 1(298 K) = (2.45 ± 0.07) × 10 -6moldm-3 and K 1(310 K) = (3.63 ± 0.08) × 10 -6moldm-3. Precipitation diagrams show that under the given experimental conditions, at 298 K, UA·2H 2O is stable for 24 h while at 310 K this was true only for precipitates formed from solutions of high supersaturations. At lower supersaturations, mixtures of UA·2H 2O and UA formed. Consequently, while the Ksp value determined from precipitation data obtained at 298 K (K sp = 1.04 × 10 -9mol2dm-6) was consistent with the respective solubility product, the 310 K precipitation boundary yielded an ion activity product, AP, the value of which fulfills the conditions Ksp(UA) < AP < Ksp (UA·2H 2O). Similar ion activity products were obtained from solubility measurements in pure water at 20 h equilibration time.

Phase study of SiO2-ZrO2 composites prepared from polymorphic combination of starting powders via a ball-milling followed by calcination

NASA Astrophysics Data System (ADS)

Musyarofah; Nurlaila, R.; Muwwaqor, N. F.; Saukani, M.; Kuswoyo, A.; Triwikantoro; Pratapa, S.

2017-04-01

The effects of SiO2-ZrO2 polymorphic combinations as starting powders and calcination temperature on phase composition of the SiO2-ZrO2 composites were studied. Stoichiometric (1:1 mol%) mixtures of the SiO2-ZrO2 composites were mechanically activated using a ball-milling for 5 h followed by calcinations at 1000, 1100 and 1200 °C for 3 h. The composites used in the present study were a-SiO2+ a-ZrO2, a-SiO2+ t-ZrO2, c-SiO2+ a-ZrO2 and c-SiO2+ t-ZrO2 which were symbolized by AA, AT, CA and CT, respectively. Prefixes a, t and c denote amorphous, tetragonal and cristobalite, respectively. The phase composition was determined by Rietveld analysis of X-ray diffraction (XRD) data using Rietica software. The identified phases for all calcined samples were a combination among t-ZrO2, c-SiO2, m-ZrO2 and zircon (ZrSiO4). Amorphous zirconia formed a transient tetragonal zirconia phase during heating, which reacted with silica to form zircon. The zircon phase was not found to form even at 1200 °C in the AT and CT mixtures and at 1100 °C in the CA mixture. The AA mixture in particular crystallized to form zircon at a lower temperature with more composition fraction than the others, ca 82.9 (14) mol%.

8,10-Diiodo-2,6-dioxo-4λ-ioda-3,5-dioxatricyclo-[5.3.1.0]undeca-1(11),7,9-triene-9-carb-oxy-lic acid.

PubMed

Sheng, Daopeng; Han, Lu; Zhang, Yi; Yang, Yanzhao

2012-03-01

In the title compound, C(9)HI(3)O(6)·2H(2)O, the mol-ecule is located on a twofold axis that gives rise to disorder of the carboxyl group. This disorder is correlated with the disorder of one of the H atoms of the water mol-ecule. The carboxyl group is twisted relative to the attached benzene ring by 75.1 (4)°. The intra-molecular I⋯O distance is 2.112 (6) Å. Mol-ecules are linked via O-H⋯O hydrogen bonding, C-I⋯O halogen bonding, with I⋯O distances in the range 3.156 (5)-3.274 (6) Å, and dipolar C=O⋯C=O inter-actions between the carboxyl and carboxyl-ate groups, with an O⋯C distance of 2.944 (10) Å.

The solubility of gold in H 2 O-H 2 S vapour at elevated temperature and pressure

NASA Astrophysics Data System (ADS)

Zezin, Denis Yu.; Migdisov, Artashes A.; Williams-Jones, Anthony E.

2011-09-01

This experimental study sheds light on the complexation of gold in reduced sulphur-bearing vapour, specifically, in H 2O-H 2S gas mixtures. The solubility of gold was determined in experiments at temperatures of 300, 350 and 365 °C and reached 2.2, 6.6 and 6.3 μg/kg, respectively. The density of the vapour varied from 0.02 to 0.22 g/cm 3, the mole fraction of H 2S varied from 0.03 to 0.96, and the pressure in the cell reached 263 bar. Statistically significant correlations of the amount of gold dissolved in the fluid with the fugacity of H 2O and H 2S permit the experimental data to be fitted to a solvation/hydration model. According to this model, the solubility of gold in H 2O-H 2S gas mixtures is controlled by the formation of sulphide or bisulphide species solvated by H 2S or H 2O molecules. Formation of gold sulphide species is favoured statistically over gold bisulphide species and thus the gold is interpreted to dissolve according to reactions of the form: Au(s)+(n+1)HS(g)=AuS·(HS)n(g)+H(g) Au(s)+HS(g)+mHO(g)=AuS·(HO)m(g)+H(g) Equilibrium constants for Reaction (A1) and the corresponding solvation numbers ( K A1 and n) were evaluated from the study of Zezin et al. (2007). The equilibrium constants as well as the hydration numbers for Reaction (A2) ( K A2 and m) were adjusted simultaneously by a custom-designed optimization algorithm and were tested statistically. The resulting values of log K A2 and m are -15.3 and 2.3 at 300 and 350 °C and -15.1 and 2.2 at 365 °C, respectively. Using the calculated stoichiometry and stability of Reactions (A1) and (A2), it is now possible to quantitatively evaluate the contribution of reduced sulphur species to the transport of gold in aqueous vapour at temperatures up to 365 °C. This information will find application in modelling gold ore-forming processes in vapour-bearing magmatic hydrothermal systems, notably those of epithermal environments.

Hydrogen-water vapor mixtures: Control of hydrothermal atmospheres by hydrogen osmosis

USGS Publications Warehouse

Shaw, H.R.

1963-01-01

Experiments at 700??C and 800 bars total pressure demonstrate positive deviations from ideality for mixtures of hydrogen and H2O gases. The deviations are greater than predicted with Stockmayer's method. The composition of the mixture and the fugacity of hydrogen are controlled by diffusing hydrogen through metallic membranes. The results give the fugacities of both H 2O and oxygen.

O2-dependent Aliphatic Carbon-carbon Bond Cleavage Reactivity in a Ni(II) Enolate Complex Having a Hydrogen Bond Donor Microenvironment; Comparison with a Hydrophobic Analog

PubMed Central

Grubel, Katarzyna; Fuller, Amy L.; Chambers, Bonnie M.; Arif, Atta M.; Berreau, Lisa M.

2010-01-01

A mononuclear Ni(II) complex having an acireductone type ligand, and supported by the bnpapa (N,N-bis((6-neopentylamino-2-pyridyl)methyl-N-((2-pyridyl)methyl)amine ligand, [(bnpapa)Ni(PhC(O)C(OH)C(O)Ph)]ClO4 (14), has been prepared and characterized by elemental analysis, 1H NMR, FTIR, and UV-vis. To gain insight into the 1H NMR features of 14, the air stable analog complexes [(bnpapa)Ni(CH3C(O)CHC(O)CH3)]ClO4 (16) and [(bnpapa)Ni(ONHC(O)CH3)]ClO4 (17) were prepared and characterized by X-ray crystallography, 1H NMR, FTIR, UV-vis, mass spectrometry, and solution conductivity measurements. Compounds 16 and 17 are 1:1 electrolyte species in CH3CN. 1H and 2H NMR studies of 14, 16, and 17 and deuterated analogs revealed that the complexes having six-membered chelate rings for the exogenous ligand (14 and 16) do not have a plane of symmetry within the solvated cation and thus exhibit more complicated 1H NMR spectra. Compound 17, as well as other simple Ni(II) complexes of the bnpapa ligand (e.g. [(bnpapa)Ni(ClO4)(CH3CN)]ClO4 (18) and [(bnpapaNi)2(μ-Cl)2](ClO4)2 (19)), exhibit 1H NMR spectra consistent with the presence of a plane of symmetry within the cation. Treatment of [(bnpapa)Ni(PhC(O)C(OH)C(O)Ph)]ClO4 (14) with O2 results in aliphatic carbon-carbon bond cleavage within the acireductone-type ligand and the formation of [(bnpapa)Ni(O2CPh)]ClO4 (9), benzoic acid, benzil, and CO. Use of 18O2 in the reaction gives high levels of incorporation (>80%) of one labeled oxygen atom into 9 and benzoic acid. The product mixture and level of 18O incorporation in this reaction is different than that exhibited by the analog supported the hydrophobic 6-Ph2TPA ligand, [(6-Ph2TPA)Ni(PhC(O)C(OH)C(O)Ph)]ClO4 (2). We propose that this difference is due to variations in the reactivity of bnpapa- and 6-Ph2TPA-ligated Ni(II) complexes with triketone and/or peroxide species produced in the reaction pathway. PMID:20039645

Gas mixture for diffuse-discharge switch

DOEpatents

Christophorou, Loucas G.; Carter, James G.; Hunter, Scott R.

1984-01-01

Gaseous medium in a diffuse-discharge switch of a high-energy pulse generator is formed of argon combined with a compound selected from the group consisting of CF.sub.4, C.sub.2 F.sub.6, C.sub.3 F.sub.8, n-C.sub.4 F.sub.10, WF.sub.6, (CF.sub.3).sub.2 S and (CF.sub.3).sub.2 O.

Gas mixture for diffuse-discharge switch

DOEpatents

Christophorou, L.G.; Carter, J.G.; Hunter, S.R.

1982-08-31

Gaseous medium in a diffuse-discharge switch of a high-energy pulse generator is formed of argon combined with a compound selected from the group consisting of CF/sub 4/, C/sub 2/F/sub 6/, C/sub 3/F/sub 8/, n-C/sub 4/F/sub 10/, WF/sub 6/, (CF/sub 3/)/sub 2/S and (CF/sub 3/)/sub 2/O.

Comparison of different advanced oxidation processes for the degradation of two fluoroquinolone antibiotics in aqueous solutions.

PubMed

Bobu, Maria; Yediler, Ayfer; Siminiceanu, Ilie; Zhang, Feifang; Schulte-Hostede, Sigurd

2013-01-01

In this study a comparative assessment using various advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(II), O(3), O(3)/UV, O(3)/UV/H(2)O(2) and O(3)/UV/H(2)O(2)/Fe(II)) was attempted to degrade efficiently two fluoroquinolone drugs ENR [enrofloxacin (1-Cyclopropyl-7-(4-ethyl-1-piperazinyl)-6-fluoro-1,4-dihydro-4-oxo-3-quinolonecarboxylic acid)] and CIP [ciprofloxacin (1-cyclopropyl-6-fluoro-4-oxo-7-(piperazin-1-yl)-quinoline-3-carboxylic acid)] in aqueous solutions at a concentrations of 0.15 mM for each drug. The efficiency of the applied oxidation processes (AOPs) has been estimated by the conversion of the original substrate (X(ENR) and X(CIP)) and the reduction of chemical oxygen demand (COD), total organic carbon (TOC). Special emphasis was laid on the effect of varying reaction pH as well as of the applied oxidant doses on the observed reaction kinetics for each advanced oxidation processes. High degradation efficiencies, particularly in terms of rates of TOC and COD abatement, were obtained for photo-Fenton assisted ozonation [O(3)/UV/H(2)O(2)/Fe(II)], compared to other advanced oxidation processes. At pH 3 and 25°C best results for the degradation of both investigated drugs were achieved when 10 mM H(2)O(2), 0.5 mM Fe(II) and an initial dose of 8.5 mg L(-1) ozone were applied. In addition, the evolution of toxicity of the reaction mixtures for different AOPs has been studied by the bioluminescence test (LUMIStox 300).

Platinum catalytic effect on oxygen fugacity of CO 2H 2 gas mixtures measured with ZrO 2 oxygen sensor at 105 Pa from 1300 to 700°C

NASA Astrophysics Data System (ADS)

Miyamoto, M.; Mikouchi, T.

1996-08-01

The oxygen fugacity of CO 2H 2 gas mixtures were measured with a ZrO 2 oxygen sensor at high temperatures in a furnace. We confirmed that the oxygen fugacity values measured by the ZrO 2 cell are more reducing than those of the CO 2H 2 gas mixtures calculated by using JANAF data at temperatures below 1150°C as was previously reported by Huebner (1975). We successfully decreased the deviation of the measured oxygen-fugacity value from the calculated one down to temperature of 800°C by using a Pt catalyst. Our results suggest that the deviation is probably due to incomplete equilibration of the gases.

Thermal inactivation of acid, cold, heat, starvation, and desiccation stress-adapted Escherichia coli O157:H7 in moisture-enhanced nonintact beef.

PubMed

Shen, Cangliang; Geornaras, Ifigenia; Belk, Keith E; Smith, Gary C; Sofos, John N

2011-04-01

This study was conducted to compare thermal inactivation of stress-adapted and nonadapted Escherichia coli O157:H7 in nonintact beef moisture enhanced with different brine formulations and cooked to 65°C. Coarsely ground beef was mixed with acid, cold, heat, starvation, or desiccation stress-adapted or nonadapted rifampin-resistant E. coli O157:H7 (eight-strain mixture, 5 to 6 log CFU/g) and a brine solution for a total moisture enhancement level of 10%. The brine treatments included distilled water (control), sodium chloride (0.5% NaCl) plus sodium tripolyphosphate (0.25% STP), or NaCl + STP combined with cetylpyridinium chloride (0.2% CPC), lactic acid (0.3% LA), or sodium metasilicate (0.2% SM). The treated meat was extruded into bags (15 cm diameter), semifrozen (-20°C for 4.5 h), and cut into 2.54-cm (1-in.)-thick portions. Samples were individually vacuum packaged, frozen (-20°C for 42 h), and tempered at 4°C for 2.5 h before cooking. Partially thawed (-1.8 ± 0.4°C) samples were pan broiled to an internal temperature of 65°C. Pathogen counts of partially thawed (before cooking) samples moisture enhanced with brines containing CPC, LA, or SM were 0.7 to 1.1, 0.0 to 0.4, and 0.2 to 0.4 log CFU/g, respectively, lower than those of the control. Compared with microbial count reductions obtained after pan broiling of beef inoculated with nonadapted E. coli O157:H7 cells, count reductions during cooking of meat inoculated with cold and desiccation stress-adapted, acid stress-adapted, and heat and starvation stress-adapted cells indicated sensitization, cross protection, and no effect, respectively, of these stresses on the pathogen during subsequent exposure to heat. Among all stressed cultures, CPC-treated samples (0.8 to 3.6 log CFU/g) and LA-treated samples (0.8 to 3.5 log CFU/g) had the lowest numbers of E. coli O157:H7 survivors after cooking.

Inflammation Modulatory Protein TSG-6 for Chemical Injuries to the Cornea

DTIC Science & Technology

2015-10-01

Col1a1 (collagen, type I, alpha 1) Col1a1 C o l1 a 1 /G A P D H co...0.25 Col1a1 C o l1 a 1 /G A P D H PB S TS G- 6 0.0 0.5 1.0 1.5 2.0 2.5 Thrombomodulin (CD141) ELANE (Neutrophil elastase) Emr1 (EGF-like module...TS G- 6 0.00 0.01 0.02 0.03 0.04 0.05 Thbd T h b d /G A P D H PB S TS G- 6 0.00 0.05 0.10 0.15 Col1a1 C o l1 a 1 /G A P D H PB S TS G- 6 0 1 2 3 4

X-ray crystallographic and tungsten-183 nuclear magnetic resonance structural studies of the [M4(H2O)2(XW9O34) 2]10- heteropolyanions (M = COII or Zn, X = P or As)

USGS Publications Warehouse

Evans, H.T.; Tourne, C.M.; Tourne, G.F.; Weakley, T.J.R.

1986-01-01

The crystal structures of K10[Co4(H2O)2(PW9O 34)2]??22H2O (1) and isomorphous K10[Zn4(H2O)2(AsW9O 34)2]??23H2O (2) have been determined {Mo-K?? radiation, space group P21/n, Z = 2; (1) a = 15.794(2), b = 21.360(2), c = 12.312(1) A??, ?? = 91.96??, R = 0.084 for 3 242 observed reflections [I ??? 3??(I)]; (2) a = 15.842(4), b = 21.327(5), c = 12.308(4) A??, ?? = 92.42(4)??, R = 0.066 for 4 675 observed reflections [F ??? 3??(F)]}. The anions have crystallographic symmetry 1 and non-crystallographic symmetry very close to 2/m (C2h). Each consists of two [XW9O34]9- moieties [??-B isomers; X = P (1) or As (2)] linked via four CoIIO6 or ZnO6 groups. Two Co or Zn atoms each carry a water ligand. The 183W n.m.r. spectra of the anions [Zn4(H2O)2(XW9O34) 2]10- (X = P or As) confirm that the anions retain 2/m symmetry in aqueous solution. Homonuclear coupling constants between 183W atoms are 5.8-9.0 Hz for adjacent WO6 octahedra sharing edges, and 19.6-25.0 Hz for octahedra sharing corners.

Synthesis of quenchable high-pressure form of magnetite (h-Fe3O4) with composition [4](Fe0.732+ Mg0.26)[6](Fe0.713+ Cr0.14Al0.10 Si0.04)2O4

NASA Astrophysics Data System (ADS)

Koch-Müller, Monika; Mugnaioli, Enrico; Rhede, Dieter; Speziale, Sergio; Kolb, Ute; Wirth, Richard

2014-05-01

Cubic inverse-spinel magnetite transforms under pressure to orthorhombic normal-spinel magnetite, h-Fe3O4 ( e.g. Fei et al. 1999; Bengtson et al. 2013). The pressure at which the transition takes place is still controversial. The high-pressure form is reported to be not quenchable to ambient conditions. We report the synthesis of h-magnetite which incorporates considerable amounts of additional cations (Cr, Mg, Al, Si) and is quenchable to ambient conditions. Two experiments were performed at 18 GPa and 1800 ° C in a multi-anvil press. The run products were investigated by electron microprobe, transmission electron microscopy and electron diffraction tomography. We observed the formation of h-magnetite in both experiments. In experiment MA-367 we used an oxide mixture with a majoritic stoichiometry Mg1.8Fe1.2(Al1.4 Cr0.2Si0.2Mg0.2)Si3O12 as starting material, with Si and Mg in excess. The Fe-oxide phase forms elongated aggregates 10-30 μm in length, mutually intergrown with majorite, the latter being the main phase of the run products coexisting with small amounts of stishovite. The formula for h-magnetite in run MA-367 was calculated as [4](Fe0.732+ Mg0.26)[6](Fe0.713+ Cr0.14Al0.10 Si0.04)2O4. In the second experiment (MA-376) we used an oxide mixture corresponding to the composition of h-magnetite obtained in MA-367. In this experiment the main phase was h-magnetite with composition [4](Fe0.982+)[6](Fe0.683+ Cr0.17Al0.13 Si0.02)2O4coexisting with very small amounts of wadsleyite. Interestingly no magnesium was incorporated into the Fe-oxide in this experiment compared to MA-367 and no iron was found in the coexisting wadsleyite. For the first time it was possible to perform electron diffraction on recovered h-magnetite of both experiments and we observed that -at least in our case- the h-magnetite structure can better be described in space group Amam than in space group Bbmm as previously proposed. The substitution of Fe by Cr, Mg, Al and Si, all smaller in atomic size, may have favored the survival of the high pressure form to ambient conditions. We prove that the h-magnetite phase is also stable in chemical systems more complex than the simple Fe-O. Based on our results obtained at 18 GPa and 1800 oC in a system that is closely related to Fe-enriched oceanic lithospheric material, we suggest that h-magnetite may be present in environments connected to deeply subducted slabs. The strong enrichment of Cr in this oxide phase implies that coexisting silicates may be depleted in Cr compared to Fe3O4-free assemblages. This would significantly affect the chemical signature of melts produced in the deep mantle. References: Fei et al. (1999) American Mineralogist, 84, 203 - 206 Bengtson et al. (2013) Physical Review B87, 155141

Partial nitrogen loss in SrTaO2N and LaTiO2N oxynitride perovskites

NASA Astrophysics Data System (ADS)

Chen, Daixi; Habu, Daiki; Masubuchi, Yuji; Torii, Shuki; Kamiyama, Takashi; Kikkawa, Shinichi

2016-04-01

SrTaO2N heated in a helium atmosphere began to release nitrogen of approximately 30 at% at 950 °C while maintaining the perovskite structure and its color changed from orange to dark green. Then it decomposed above 1200 °C to a black mixture of Sr1.4Ta0.6O2.73, Ta2N, and Sr5Ta4O15. The second decomposition was not clearly observed when SrTaO2N was heated in a nitrogen atmosphere below 1550 °C. After heating at 1500 °C for 3 h under a 0.2 MPa nitrogen atmosphere, the perovskite product became dark green and conductive. Structure refinement results suggested that the product was a mixture of tetragonal and cubic perovskites with a decreased ordering of N3-/O2-. The sintered body was changed to an n-type semiconductor after a partial loss of nitrogen to be reduced from the originally insulating SrTaO2N perovskite lattice. LaTiO2N was confirmed to have a similar cis-configuration of the TiO4N2 octahedron as that of TaO4N2 in SrTaO2N. It also released some of its nitrogen at 800 °C changing its color from brown to black and then decomposed to a mixture of LaTiO3, La2O3, and TiN at 1100 °C. These temperatures are lower than those in SrTaO2N.

Effect of H2O and CO2 on The Oxidation Behavior and Durability at High Temperature of ODS-FeCrAl

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dryepondt, Sebastien N; Rouaix-Vande Put, Aurelie; Pint, Bruce A

Cyclic oxidation testing was conducted on alloy MA956 and two different batches of alloy PM2000 at 1100 and 1200 C in different atmospheres rich in O2, H2O and CO2. Compare to 1h cycle in dry O2, exposure in air + 10 vol.% H2O resulted in an increase of the oxidation rate and a decrease of the time to breakaway for both alloys at 1200 C, and a faster consumption of Al in the MA956 alloy. 1h cyclic testing in 50%CO2/50%H2O+0.75% O2 had less of an impact on the oxidation rate but led to an increased formation of voids for alloymore » MA956, which had an impact on the alloy creep resistance. At 1100 C, exposure in 50%CO2/50%H2O resulted in significant oxide spallation compared with oxidation in air, but it was not the case when 0.75% O2 was added to the CO2/H2O mixture as a buffer. The control of impurities levels drastically improved the PM2000 oxidation resistance.« less

Crystal structures of dioxonium hexafluorotantalate and dioxonium hexafluoroniobate complexes with tetrabenzo-30-crown-10

DOE Office of Scientific and Technical Information (OSTI.GOV)

Furmanova, N. G., E-mail: furm@ns.crys.ras.ru; Rabadanov, M. Kh.; Chernaya, T. S.

2008-03-15

Two isostructural complexes of dioxonium [H{sub 5}O{sub 2}]{sup +} with tetrabenzo-30-crown-10 of the compositions [(tetrabenzo-30-crown-10 {center_dot} H{sub 5}O{sub 2})][TaF{sub 6}] (I) and [(tetrabenzo-30-crown-10 {center_dot} H{sub 5}O{sub 2})][NbF{sub 6}] (II) are studied using X-ray diffraction. The complexes crystallize in the monoclinic crystal system (space group C2/c, Z = 4). The unit cell parameters of these compounds are as follows: a = 15.6583(12) Angstrom-Sign , b = 15.2259(13) Angstrom-Sign , c = 16.4473(13) Angstrom-Sign , and {beta} = 99.398(6) Degree-Sign for complex I and a = 15.7117(12) Angstrom-Sign , b = 15.2785(15) Angstrom-Sign , c = 16.5247(15) Angstrom-Sign , and {beta} =more » 99.398(7) Degree-Sign for complex II. These complexes belong to the ionic type. The dioxonium cation [H{sub 5}O{sub 2}]{sup +} in the form of the two-unit cluster [H{sub 3}O {center_dot} H{sub 2}O]{sup +} is stabilized by the strong hydrogen bond OH Midline-Horizontal-Ellipsis O [O Midline-Horizontal-Ellipsis O, 2.353(4) Angstrom-Sign ] and encapsulated by the crown ether. Each oxygen atom of the dioxonium cation also forms two oxygen bonds O Midline-Horizontal-Ellipsis O(crown). The crown ether adopts an unusual two-level (pocket-like) conformation, which provides a complete encapsulation of the oxonium associate. The interaction of the cationic complex with the anion in the crystal occurs through contacts of the C-H Midline-Horizontal-Ellipsis F type.« less

Tris(5,6-dimethyl-1H-benzimidazole-κN 3)(pyridine-2,6-dicarboxyl­ato-κ3 O 2,N,O 6)nickel(II)

PubMed Central

Li, Yue-Hua; Li, Feng-Feng; Liu, Xin-Hua; Zhao, Ling-Yan

2012-01-01

The title mononuclear complex, [Ni(C7H3NO4)(C9H10N2)3], shows a central NiII atom which is coordinated by two carboxyl­ate O atoms and the N atom from a pyridine-2,6-dicarboxyl­ate ligand and by three N atoms from different 5,6-dimethyl-1H-­benzimidazole ligands in a distorted octa­hedral geometry. The crystal structure shows intermolecular N—H⋯O hydrogen bonds. PMID:22719301

Polyoxomolybdates functionalized by a flexible carboxylic acid and their photochromic properties

NASA Astrophysics Data System (ADS)

Wang, Jin; Ma, Pengtao; Wang, Yaping; Zhang, Dongdi; Niu, Jingyang; Wang, Jingping

2017-11-01

Two inorganic-organic hybridized polyoxomolybdates, Cs8NaH [(SeMo6O21)C6H3O3(CH2CO2)3]2·10H2O (1) and Cs8H4 [(AsMo6O21)C6H3O3(CH2CO2)3]2·10H2O (2), functionalized by a flexible tri-podal multicarboxylic ligand 1,3,5-tris (carboxymethoxy)benzene (TCMB) have been synthesized and characterized. Single-crystal X-ray diffraction analysis reveals that each of the two hybrids consists of two {XMo6} (X = Se, As) units supported by two TCMB molecules. The photochromism and thermochromism behaviors of the two compounds have been explored. The color of compound 2 could change dramatically from white to black within just 1 min of irradiation by a Xe lamp. During thermochromic experiments the two compounds change their color at 423 K for 1 and 393 K for 2, respectively.

Optimization of intermolecular potential parameters for the CO2/H2O mixture.

PubMed

Orozco, Gustavo A; Economou, Ioannis G; Panagiotopoulos, Athanassios Z

2014-10-02

Monte Carlo simulations in the Gibbs ensemble were used to obtain optimized intermolecular potential parameters to describe the phase behavior of the mixture CO2/H2O, over a range of temperatures and pressures relevant for carbon capture and sequestration processes. Commonly used fixed-point-charge force fields that include Lennard-Jones 12-6 (LJ) or exponential-6 (Exp-6) terms were used to describe CO2 and H2O intermolecular interactions. For force fields based on the LJ functional form, changes of the unlike interactions produced higher variations in the H2O-rich phase than in the CO2-rich phase. A major finding of the present study is that for these potentials, no combination of unlike interaction parameters is able to adequately represent properties of both phases. Changes to the partial charges of H2O were found to produce significant variations in both phases and are able to fit experimental data in both phases, at the cost of inaccuracies for the pure H2O properties. By contrast, for the Exp-6 case, optimization of a single parameter, the oxygen-oxygen unlike-pair interaction, was found sufficient to give accurate predictions of the solubilities in both phases while preserving accuracy in the pure component properties. These models are thus recommended for future molecular simulation studies of CO2/H2O mixtures.

Microstructure characterization and phase transformation kinetic study of ball-milled m-ZrO 2-30 mol% a-TiO 2 mixture by Rietveld method

NASA Astrophysics Data System (ADS)

Pradhan, S. K.; Dutta, H.

2005-05-01

High-energy ball milling of monoclinic ZrO 2-30 mol% anatase TiO 2 mixture at different durations results in the formation of m-ZrO 2-a-TiO 2 solid solution from which the nucleation of nanocrystalline cubic (c) ZrO 2 polymorphic phase sets in. Post-annealing of 12 h ball-milled sample at different elevated temperatures for 1 h results in almost complete formation of c-ZrO 2 phase. Microstructure of the unmilled, all the ball milled and annealed samples has been characterized by Rietveld's X-ray powder structure refinement method. Particle size, rms lattice strain, change in lattice parameters and phase content of individual phases have been estimated from Rietveld analysis, and are utilized to interpret the results. In course of milling, (1 1 1) of cubic lattice became parallel to ( 1bar 1 1) plane of monoclinic lattice due to the orientation effect and cubic phase may have been formed on the (0 0 1) of the m-ZrO 2-a-TiO 2 solid solution lattice. A comparative study of microstructure and phase transformation kinetics of ZrO 2-10, 20 and 30 mol% a-TiO 2 ball-milled and post-annealed samples reveals that rate of phase transformation m→c-ZrO 2 increases with increasing a-TiO 2 concentration and ∼30 mol% of nanocrystalline c-ZrO 2 phase can be obtained within 4 h of milling time in the presence of 30 mol% of a-TiO 2. The post-annealing treatment at 773, 873 and 973 K for 1 h duration each reveals that rate of c-ZrO 2 formation with increasing temperature is retarded with increasing a-TiO 2 concentration but the amount of c-ZrO 2 becomes almost equal (∼95 mol%) at 973 K. It suggests that almost fully stabilized nanocrystalline c-ZrO 2 can be formed by adding a tetravalent solute to m-ZrO 2.

A novel technique for measurement of thermal rate constants and temperature dependences of dissociative recombination: CO{sub 2}{sup +}, CF{sub 3}{sup +}, N{sub 2}O{sup +}, C{sub 7}H{sub 8}{sup +}, C{sub 7}H{sub 7}{sup +}, C{sub 6}H{sub 6}{sup +}, C{sub 6}H{sub 5}{sup +}, C{sub 5}H{sub 6}{sup +}, C{sub 4}H{sub 4}{sup +}, and C{sub 3}H{sub 3}{sup +}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fournier, Joseph A.; Shuman, Nicholas S.; Melko, Joshua J.

A novel technique using a flowing afterglow-Langmuir probe apparatus for measurement of temperature dependences of rate constants for dissociative recombination (DR) is presented. Low ({approx}10{sup 11} cm{sup -3}) concentrations of a neutral precursor are added to a noble gas/electron afterglow plasma thermalized at 300-500 K. Charge exchange yields one or many cation species, each of which may undergo DR. Relative ion concentrations are monitored at a fixed reaction time while the initial plasma density is varied between 10{sup 9} and 10{sup 10} cm{sup -3}. Modeling of the decrease in concentration of each cation relative to the non-recombining noble gas cationmore » yields the rate constant for DR. The technique is applied to several species (O{sub 2}{sup +}, CO{sub 2}{sup +}, CF{sub 3}{sup +}, N{sub 2}O{sup +}) with previously determined 300 K values, showing excellent agreement. The measurements of those species are extended to 500 K, with good agreement to literature values where they exist. Measurements are also made for a range of C{sub n}H{sub m}{sup +} (C{sub 7}H{sub 7}{sup +}, C{sub 7}H{sub 8}{sup +}, C{sub 5}H{sub 6}{sup +}, C{sub 4}H{sub 4}{sup +}, C{sub 6}H{sub 5}{sup +}, C{sub 3}H{sub 3}{sup +}, and C{sub 6}H{sub 6}{sup +}) derived from benzene and toluene neutral precursors. C{sub n}H{sub m}{sup +} DR rate constants vary from 8-12 Multiplication-Sign 10{sup -7} cm{sup 3} s{sup -1} at 300 K with temperature dependences of approximately T{sup -0.7}. Where prior measurements exist these results are in agreement, with the exception of C{sub 3}H{sub 3}{sup +} where the present results disagree with a previously reported flat temperature dependence.« less

Preparation of niobium based oxynitride nanosheets by exfoliation of Ruddlesden-Popper phase precursor

NASA Astrophysics Data System (ADS)

da Silva Maia, Ary; Cheviré, François; Demange, Valérie; Bouquet, Valérie; Pasturel, Mathieu; Députier, Stéphanie; Lebullenger, Ronan; Guilloux-Viry, Marylline; Tessier, Franck

2016-04-01

A new oxynitride Ruddlesden-Popper phase K1.6Ca2Nb3O9.4N0.6.1.1H2O was synthesized by the topochemical ammonolysis reaction at 700 °C from the oxide Dion-Jacobson phase KCa2Nb3O10 in the presence of K2CO3. The oxynitride showed good stability with a little loss of nitrogen, even after a few months of exposure to air. Its crystal structure was solved by Rietveld refinement of X-ray powder diffraction data in space group P4/mmm and considering a two-phase mixture, due to the difference in the degree of hydration, with a = 3.894(2) Å and c = 17.90(8) Å for the most hydrated phase and a = 3.927(6) Å and c = 17.09(2) Å for the less one. Optical band gaps were measured by diffuse reflectance in the UV-Visible range indicating a red shift of Eg to the visible region. The oxynitride layered perovskite was then protonated and exfoliated into nanosheets. TEM images and SAED patterns of the nanosheets proved that exfoliation was successful, showing lattice parameters quite compatible with the Rietveld refinement.

Viscosities of aqueous blended amines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, C.H.; Li, M.H.

1997-07-01

Solutions of alkanolamines are an industrially important class of compounds used in the natural gas, oil refineries, petroleum chemical plants, and synthetic ammonia industries for the removal of acidic components like CO{sub 2} and H{sub 2}S from gas streams. The viscosities of aqueous mixtures of diethanolamine (DEA) + N-methyldiethanolamine (MDEA), DEA + 2-amino-2-methyl-1-propanol (AMP), and monoethanolamine (MEA) + 2-piperidineethanol (2-PE) were measured from 30 C to 80 C. A Redlich-Kister equation for the viscosity deviation was applied to represent the viscosity. On the basis of the available viscosity data for five ternary systems, MEA + MDEA + H{sub 2}O, MEAmore » + AMP + H{sub 2}O, DEA + MDEA + H{sub 2}O, DEA + AMP + H{sub 2}O, and MEA + 2-PE + H{sub 2}O, a generalized set of binary parameters were determined. For the viscosity calculation of the systems tested, the overall average absolute percent deviation is about 1.0% for a total of 499 data points.« less

Antitubercular activity of Arctium lappa and Tussilago farfara extracts and constituents.

PubMed

Zhao, Jinlian; Evangelopoulos, Dimitrios; Bhakta, Sanjib; Gray, Alexander I; Seidel, Véronique

2014-08-08

Arctium lappa and Tussilago farfara (Asteraceae) are two plant species used traditionally as antitubercular remedies. The aim of this study was (i) to screen Arctium lappa and Tussilago farfara extracts for activity against Mycobacterium tuberculosis and (ii) to isolate and identify the compound(s) responsible for this reputed anti-TB effect. The activity of extracts and isolated compounds was determined against Mycobacterium tuberculosis H37Rv using a high throughput spot culture growth inhibition (HT-SPOTi) assay. The n-hexane extracts of both plants, the ethyl acetate extract of Tussilago farfara and the dichloromethane phase derived from the methanol extract of Arctium lappa displayed antitubercular activity (MIC 62.5 μg/mL). Further chemical investigation of Arctium lappa led to the isolation of n-nonacosane (1), taraxasterol acetate (2), taraxasterol (3), a (1:1) mixture of β sitosterol/stigmasterol (4), isololiolide (5), melitensin (6), trans-caffeic acid (7), kaempferol (8), quercetin (9), kaempferol-3-O-glucoside (10). Compounds isolated from Tussilago farfara were identified as a (1:1) mixture of β sitosterol/stigmasterol (4), trans-caffeic acid (7), kaempferol (8), quercetin (9), kaempferol-3-O-glucoside (10), loliolide (11), a (4:1) mixture of p-coumaric acid/4-hydroxybenzoic acid (12), p-coumaric acid (13). All compounds were identified following analyses of their physicochemical and spectroscopic data (MS, (1)H and (13)C-NMR) and by comparison with published data. This is the first report of the isolation of n-nonacosane (1), isololiolide (5), melitensin (6) and kaempferol-3-O-glucoside (10) from Arctium lappa, and of loliolide (11) from Tussilago farfara. Amongst the isolated compounds, the best activity was observed for p-coumaric acid (13) (MIC 31.3 μg/mL or 190.9 μM) alone and in mixture with 4-hydroxybenzoic acid (12) (MIC 62.5 μg/mL). The above results provide for the first time some scientific evidence to support, to some extent, the ethno-medicinal use of Arctium lappa and Tussilago farfara as traditional antitubercular remedies. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Rate Controlling Step in the Reduction of Iron Oxides; Kinetics and Mechanism of Wüstite-Iron Step in H2, CO and H2/CO Gas Mixtures

NASA Astrophysics Data System (ADS)

El-Geassy, Abdel-Hady A.

2017-09-01

Wüstite (W1 and W2) micropellets (150-50 μm) were prepared from the reduction of pure Fe2O3 and 2.1% SiO2-doped Fe2O3 in 40%CO/CO2 gas mixture at 1000°C which were then isothermally reduced in H2, CO and H2/CO gas mixtures at 900-1100°C. The reduction reactions was followed by Thermogravimetric Analysis (TG) technique. The effect of gas composition, gas pressure and temperature on the rate of reduction was investigated. The different phases formed during the reduction were chemically and physically characterized. In SiO2-doped wüstite, fayalite (Fe2SiO3) was identified. At the initial reduction stages, the highest rate was obtained in H2 and the lowest was in CO gas. In H2/CO gas mixtures, the measured rate did not follow a simple additive equation. The addition of 5% H2 to CO led to a measurable increase in the rate of reduction compared with that in pure CO. Incubation periods were observed at the early reduction stages of W1 in CO at lower gas pressure (<0.25 atm). In SiO2-doped wüstite, reaction rate minimum was detected in H2 and H2-rich gas mixtures at 925-950°C. The influence of addition of H2 to CO or CO to H2 on the reduction reactions, nucleation and grain growth of iron was intensively studied. Unlike in pure wüstite, the presence of fayalite enhances the reduction reactions with CO and CO-rich gas mixtures. The chemical reaction equations of pure wüstite with CO are given showing the formation of carbonyl-like compound [Fem(CO2)n]*. The apparent activation energy values, at the initial stages, ranged from 53.75 to 133.97 kJ/mole indicating different reaction mechanism although the reduction was designed to proceed by the interfacial chemical reaction.

Synthesis and Properties of Selected Energetic Organodi- and Polyammonium Nitrate Salts

DTIC Science & Technology

1986-04-01

NNN-Substituted EDO 9N,- 81. N,NN-Timehyethyenediaronium dinitrate TRDMEDD COH1 N40 12. N,N-Dimety’ethylethylenedia nwonium d nitrate O-MED C0H10...thus forming a mixture of piperidinium nitrate and amonium nitrate . No characterization of the oil was attempted. 1H nuclear magnetic resonance spectra...AFATL-TR-86-O8 Synthesis and Properties of Selected Energetic Org anodi - and Polyammonium Nitrate Salts Dr Robert L McKenney, Jr Maj Robert A

Structural Mimics of the [Fe]-Hydrogenase: A Complete Set for Group VIII Metals.

PubMed

Barik, Chandan Kr; Ganguly, Rakesh; Li, Yongxin; Leong, Weng Kee

2018-06-18

A set of structural mimics of the [Fe]-hydrogenase active site comprising all the group VIII metals, viz., [M(2-NHC(O)C 5 H 4 N)(CO) 2 (2-S-C 5 H 4 N)], has been synthesized. They exist as a mixture of isomers in solution, and the relative stability of the isomers depends on the nature of the metal and the substituent at the 6-position of the pyridine ligand.

Detection of abundant ethane and methane, along with carbon monoxide and water, in comet C/1996 B2 Hyakutake: evidence for interstellar origin

NASA Technical Reports Server (NTRS)

Mumma, M. J.; DiSanti, M. A.; Dello Russo, N.; Fomenkova, M.; Magee-Sauer, K.; Kaminski, C. D.; Xie, D. X.

1996-01-01

The saturated hydrocarbons ethane (C2H6) and methane (CH4) along with carbon monoxide (CO) and water (H2O) were detected in comet C/1996 B2 Hyakutake with the use of high-resolution infrared spectroscopy at the NASA Infrared Telescope Facility on Mauna Kea, Hawaii. The inferred production rates of molecular gases from the icy, cometary nucleus (in molecules per second) are 6.4 X 10(26) for C2H6, 1.2 X 10(27) for CH4, 9.8 X 10(27) for CO, and 1.7 X 10(29) for H2O. An abundance of C2H6 comparable to that of CH4 implies that ices in C/1996 B2 Hyakutake did not originate in a thermochemically equilibrated region of the solar nebula. The abundances are consistent with a kinetically controlled production process, but production of C2H6 by gas-phase ion molecule reactions in the natal cloud core is energetically forbidden. The high C2H6/CH4 ratio is consistent with production of C2H6 in icy grain mantles in the natal cloud, either by photolysis of CH4-rich ice or by hydrogen-addition reactions to acetylene condensed from the gas phase.

Synthetic and structural investigations of mercurous and mercuric organophosphonates and phenylarsonates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Padalwar, Nitin Balkrushna; Vidyasagar, Kanamaluru

2016-11-15

The following twelve mercurous and mercuric organophosphomates, bis/diphosphonates and phenylarsonates have been isolated and structurally characterized by single crystal X-ray diffraction, {sup 13}C-and {sup 31}P NMR, infrared and Raman spectroscopic methods: Hg{sub 2}(HO{sub 3}PC{sub 6}H{sub 5}){sub 2}(1), Hg{sub 2}(HO{sub 3}P(C{sub 6}H{sub 4})PO{sub 3}H)(2), Hg{sub 2}(HO{sub 3}P(C{sub 6}H{sub 4}){sub 2}PO{sub 3}H)(3), Hg{sub 2}(HO{sub 3}P(CH{sub 2}){sub 4}PO{sub 3}H)(4), Hg{sub 2}(O{sub 3}PC{sub 6}H{sub 5})·H{sub 2}O(5), (Hg{sub 2}){sub 2}(O{sub 3}P(CH{sub 2}){sub 2}PO{sub 3})(6), (Hg{sub 2}){sub 2}(O{sub 3}P(CH{sub 2}){sub 3}PO{sub 3})(7), Hg(O{sub 3}PC{sub 6}H{sub 5})·H{sub 2}O(8), Hg(O{sub 3}PCH{sub 2}C{sub 6}H{sub 5})·H{sub 2}O(9), Hg(O{sub 3}AsC{sub 6}H{sub 5})·H{sub 2}O(10), Hg{sub 3}(O{sub 3}AsC{sub 6}H{sub 5}){sub 2}(HO{sub 3}AsC{sub 6}H{submore » 5}){sub 2}(11) and (Hg{sub 2})Hg{sub 3}(O{sub 3}P(C{sub 6}H{sub 4})PO{sub 3}){sub 2}·2H{sub 2}O(12). Compounds 1–7 are the first examples of mercurous phosphonates and di/bisphosphonates. They contain Hg{sub 2}O{sub 6} units, which consist of Hg{sub 2}{sup 2+} cations with Hg-Hg bond of ~2.5 Å length. Phenylphosphonates 1 and 5 are layered compounds, whereas bis/diphosphonates 2, 3, 4, 6 and 7 have pillared-layered and three-dimensional structures. Compounds 8–11 are layered mercuric phosphonates and phenylarsonates. Compound 12 is a three-dimensional mixed-valent mercury phenylenebisphosphonate. - Graphical abstract: The first examples of mercurous organophosphonates and organodiphosphonates have layered, pillared-layered and three-dimensional structures.« less

The graphite deposit at Borrowdale (UK): A catastrophic mineralizing event associated with Ordovician magmatism

NASA Astrophysics Data System (ADS)

Ortega, L.; Millward, D.; Luque, F. J.; Barrenechea, J. F.; Beyssac, O.; Huizenga, J.-M.; Rodas, M.; Clarke, S. M.

2010-04-01

The volcanic-hosted graphite deposit at Borrowdale in Cumbria, UK, was formed through precipitation from C-O-H fluids. The δ 13C data indicate that carbon was incorporated into the mineralizing fluids by assimilation of carbonaceous metapelites of the Skiddaw Group by andesite magmas of the Borrowdale Volcanic Group. The graphite mineralization occurred as the fluids migrated upwards through normal conjugate fractures forming the main subvertical pipe-like bodies. The mineralizing fluids evolved from CO 2-CH 4-H 2O mixtures (XCO 2 = 0.6-0.8) to CH 4-H 2O mixtures. Coevally with graphite deposition, the andesite and dioritic wall rocks adjacent to the veins were intensely hydrothermally altered to a propylitic assemblage. The initial graphite precipitation was probably triggered by the earliest hydration reactions in the volcanic host rocks. During the main mineralization stage, graphite precipitated along the pipe-like bodies due to CO 2 → C + O 2. This agrees with the isotopic data which indicate that the first graphite morphologies crystallizing from the fluid (cryptocrystalline aggregates) are isotopically lighter than those crystallizing later (flakes). Late chlorite-graphite veins were formed from CH 4-enriched fluids following the reaction CH 4 + O 2 → C + 2H 2O, producing the successive precipitation of isotopically lighter graphite morphologies. Thus, as mineralization proceeded, water-generating reactions were involved in graphite precipitation, further favouring the propylitic alteration. The structural features of the pipe-like mineralized bodies as well as the isotopic homogeneity of graphite suggest that the mineralization occurred in a very short period of time.

Effect of H2O and CO2 on The Oxidation Behavior and Durability at High Temperature of ODS-FeCrAl

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dryepondt, Sebastien N; Pint, Bruce A; Rouaix-Vande Put, Aurelie

Cyclic oxidation testing was conducted on alloy MA956 and two different batches of alloy PM2000 at 1100 and 1200 C in different atmospheres rich in O2, H2O and CO2. Compared to 1h cycles in dry O2, exposure in air+10 vol.% H2O resulted in an increase of the oxidation rate and a decrease of the time to breakaway for all alloys at 1200 C, and a faster consumption of Al in the MA956 alloy. One hour cyclic testing in 49.25%CO2+50%H2O+0.75% O2 had a smaller effect on the oxidation rate but led to increased formation of voids in alloy MA956, which hadmore » an impact on the alloy creep resistance. At 1100 C, exposure in 50%CO2+50%H2O resulted in significant oxide spallation compared with oxidation in air, but this was not the case when 0.75% O2 was added to the CO2/H2O mixture as a buffer. The control of impurity levels drastically improved the oxidation resistance of PM2000.« less

Synthesis of molecularly imprinted polymers by atom transfer radical polymerization for the solid-phase extraction of phthalate esters in edible oil.

PubMed

Chen, Ningning; He, Juan; Wu, Chaojun; Li, Yuanyuan; Suo, An; Wei, Hongliang; He, Lijun; Zhang, Shusheng

2017-03-01

Novel molecularly imprinted polymers of phthalate esters were prepared by atom transfer radical polymerization using methyl methacrylate as functional monomer, cyclohexanone as solvent, cuprous chloride as catalyst, 1-chlorine-1-ethyl benzene as initiator and 2,2-bipyridyl as cross-linker in the mixture of methanol and water (1:1, v/v). The effect of reaction conditions such as monomer ratio and template on the adsorption properties was investigated. The optimum condition was obtained by an orthogonal experiment. The obtained polymers were characterized using scanning electron microscopy. The binding property was studied with both static and dynamic methods. Results showed that the polymers exhibited excellent recognition capacity and outstanding selectivity for ten phthalate esters. Factors affecting the extraction efficiency of the molecularly imprinted solid-phase extraction were systematically investigated. An analytical method based on the molecularly imprinted coupled with gas chromatography and flame ionization detection was successfully developed for the simultaneous determination of ten phthalate esters from edible oil. The method detection limits were 0.10-0.25 μg/mL, and the recoveries of spiked samples were 82.5-101.4% with relative standard deviations of 1.24-5.37% (n = 6). © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Derivation of the P2T Criterion (in Closed Form) Based on the Frey Shear Band Mechanism

DTIC Science & Technology

1984-01-01

max 6d/d = G (12) max o u Pil < o .tlllilltt, >. X !5 < Q: o W) TJ C rH CU •H ed •P in -H 03 W 4-" FH cd C 03 Cu <U P...C 3 -H 10 T3 cd T3 O H s h ♦J 03 PH If) X3 -d rH fH ^H ed 03 OJ -H (1) •H -t-i Xi MH -H in c X’H <D ■M 43 • H 0 +J O...P o c a> rH X! 0 M 03 w C M •H O 03 u S & K <u TO S 0) +-> FH O ^—^ o3 W) y ^ cd i S: •H -H O -d T3 T3 iH CD *W P O nj

The promotion effect of coexisting hygroscopic composition on the reaction between oxalic acid and calcite during humidifying process

NASA Astrophysics Data System (ADS)

Ma, Q.; He, H.

2012-12-01

Internally mixed oxalic acid with mineral dust has been frequently detected in field measurements (Sullivan and Prather, 2007; Wang et al., 2012; Yang et al., 2009). Meanwhile, Furukawa and Takahashi (Furukawa and Takahashi, 2011) found that most of the oxalic acid in mineral mixture is present as metal oxalate complexes in the aerosols, however, the formation mechanism of these complexes is not well known. It was reported that cloud process of H2C2O4/CaCO3 mixture could lead to the formation of calcium oxalate (Gierlus et al., 2012). Recently, we used Raman spectroscopy to investigate the hygroscopic behavior of H2C2O4/CaCO3 mixture below saturation condition as well as the effect of coexisting hygroscopic compositions, e.g. Ca(NO3)2, NaCl, NH4NO3, and (NH4)2SO4. It was found that there was no interaction between H2C2O4 and calcite without third component during humidifying process under ambient condition. In contrast, the presence of coexisting Ca(NO)3, NaCl, or NH4NO3 could promote the reaction between H2C2O4 and calcite by providing an aqueous circumstance after deliquescence, resulting in the formation of calcium oxalate hydrates. Moreover, substitution of strong acid (HNO3) by medium acid (H2C2O4) occurred when water vapor was absorbed in Ca(NO3)2/H2C2O4 mixture (Ma and He, 2012). As for (NH4)2SO4, there existed a competition effect between (NH4)2SO4 and H2C2O4 for the reaction with CaCO3. CaCO3 was preferentially reacted with (NH4)2SO4 to form gypsum in the solution, while the residual NH4+ and C2O42- ions were bonded to (NH4)2C2O4 after efflorescence. These results implies a potential formation pathway of metal oxalate complexes in the atmosphere and also suggests that synergistic effect between different constituents in humidifying process of mixed particles should be considered in future hygroscopic behavior studies.

Bis[4-(4-pyridyl)pyridinium] (4-carboxy­pyridine-2,6-dicarboxyl­ato-κ3 O 2,N,O 6)(pyridine-2,4,6-tricarboxyl­ato-κ3 O 2,N,O 6)ferrate(III) trihydrate

PubMed Central

Zhao, Li; Dong, You-Ren; Xie, Hong-Zhen

2009-01-01

In the title salt, (C10H9N2)2[Fe(C8H2NO6)(C8H3NO6)]·3H2O, the FeIII atom is O,N,O′-chelated by dianionic and trianionic ligands in a slightly distorted octa­hedral coordination geometry. The cations and ferrate anions are linked into a layered structure; the layers are connected through the uncoordinated water mol­ecules into a hydrogen-bonded three-dimensional supra­molecular structure. One of the uncoordinated water molecules is disordered around an inversion centre and was refined with half-occupancy for each position. PMID:21582387

Initial Reaction(s) in Biotransformation of CL-20 Is Catalyzed by Salicylate 1-Monooxygenase from Pseudomonas sp. Strain ATCC 29352

PubMed Central

Bhushan, Bharat; Halasz, Annamaria; Spain, Jim C.; Hawari, Jalal

2004-01-01

CL-20 (2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane) (C6H6N12O12), a future-generation high-energy explosive, is biodegradable by Pseudomonas sp. strain FA1 and Agrobacterium sp. strain JS71; however, the nature of the enzyme(s) involved in the process was not understood. In the present study, salicylate 1-monooxygenase, a flavin adenine dinucleotide (FAD)-containing purified enzyme from Pseudomonas sp. strain ATCC 29352, biotransformed CL-20 at rates of 0.256 ± 0.011 and 0.043 ± 0.003 nmol min−1 mg of protein−1 under anaerobic and aerobic conditions, respectively. The disappearance of CL-20 was accompanied by the release of nitrite ions. Using liquid chromatography/mass spectrometry in the negative electrospray ionization mode, we detected a metabolite with a deprotonated mass ion [M − H]− at 345 Da, corresponding to an empirical formula of C6H6N10O8, produced as a result of two sequential N denitration steps on the CL- 20 molecule. We also detected two isomeric metabolites with [M − H]− at 381 Da corresponding to an empirical formula of C6H10N10O10. The latter was a hydrated product of the metabolite C6H6N10O8 with addition of two H2O molecules, as confirmed by tests using 18O-labeled water. The product stoichiometry showed that each reacted CL-20 molecule produced about 1.7 nitrite ions, 3.2 molecules of nitrous oxide, 1.5 molecules of formic acid, and 0.6 ammonium ion. Diphenyliodonium-mediated inhibition of salicylate 1-monooxygenase and a comparative study between native, deflavo, and reconstituted enzyme(s) showed that FAD site of the enzyme was involved in the biotransformation of CL-20 catalyzed by salicylate 1-monooxygenase. The data suggested that salicylate 1-monooxygenase catalyzed two oxygen-sensitive single-electron transfer steps necessary to release two nitrite ions from CL-20 and that this was followed by the secondary decomposition of this energetic chemical. PMID:15240281

Initial reaction(s) in biotransformation of CL-20 is catalyzed by salicylate 1-monooxygenase from Pseudomonas sp. strain ATCC 29352.

PubMed

Bhushan, Bharat; Halasz, Annamaria; Spain, Jim C; Hawari, Jalal

2004-07-01

CL-20 (2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane) (C(6)H(6)N(12)O(12)), a future-generation high-energy explosive, is biodegradable by Pseudomonas sp. strain FA1 and Agrobacterium sp. strain JS71; however, the nature of the enzyme(s) involved in the process was not understood. In the present study, salicylate 1-monooxygenase, a flavin adenine dinucleotide (FAD)-containing purified enzyme from Pseudomonas sp. strain ATCC 29352, biotransformed CL-20 at rates of 0.256 +/- 0.011 and 0.043 +/- 0.003 nmol min(-1) mg of protein(-1) under anaerobic and aerobic conditions, respectively. The disappearance of CL-20 was accompanied by the release of nitrite ions. Using liquid chromatography/mass spectrometry in the negative electrospray ionization mode, we detected a metabolite with a deprotonated mass ion [M - H](-) at 345 Da, corresponding to an empirical formula of C(6)H(6)N(10)O(8), produced as a result of two sequential N denitration steps on the CL- 20 molecule. We also detected two isomeric metabolites with [M - H](-) at 381 Da corresponding to an empirical formula of C(6)H(10)N(10)O(10). The latter was a hydrated product of the metabolite C(6)H(6)N(10)O(8) with addition of two H(2)O molecules, as confirmed by tests using (18)O-labeled water. The product stoichiometry showed that each reacted CL-20 molecule produced about 1.7 nitrite ions, 3.2 molecules of nitrous oxide, 1.5 molecules of formic acid, and 0.6 ammonium ion. Diphenyliodonium-mediated inhibition of salicylate 1-monooxygenase and a comparative study between native, deflavo, and reconstituted enzyme(s) showed that FAD site of the enzyme was involved in the biotransformation of CL-20 catalyzed by salicylate 1-monooxygenase. The data suggested that salicylate 1-monooxygenase catalyzed two oxygen-sensitive single-electron transfer steps necessary to release two nitrite ions from CL-20 and that this was followed by the secondary decomposition of this energetic chemical.

Effects of solutions treated with oxygen radicals in neutral pH region on inactivation of microorganism

NASA Astrophysics Data System (ADS)

Kobayashi, Tsuyoshi; Hashizume, Hiroshi; Ohta, Takayuki; Ishikawa, Kenji; Hori, Masaru; Ito, Masafumi

2015-09-01

The inactivation of microorganisms using nonequilbrium atmospheric pressure plasmas has been attracted much attention due to the low temperature processing and high speed treatment. In this study, we have inactivated E. coli suspended in solutions with neutral pH using an atmospheric-pressure oxygen radical source which can selectively supply electrically neutral oxygen radicals. E. coli cells were suspended with deionized distilled water (DDW) (pH = 6.8) or phosphate buffered saline (PBS) (pH = 7.4) or Citrate-Na buffer (pH = 6.5). The treated samples were diluted and spread on nutrient agar (Nutrient Broth). They were cultured at 37° C. The inactivation effects of oxygen radicals on those cells in solutions were evaluated by colony-counting method. O2 diluted by Ar gas were employed as a working gas for the radical source. The total gas flow rate and the gas mixture ratio of O2/(Ar + O2) were set at 5 slm and 0.6%, respectively. The distance between the radical exit and the suspension surface were set at 10 mm. As a result, the D values for DDW(pH = 6.8), PBS(pH = 7.4) and Citrate-Na buffer(pH = 6.5) were estimated to be 1.4 min, 0.9 min and 16.8 min respectively. The inactivation rates in DDW, PBS were significantly different from that in Citrate-Na buffer. This work was partly supported by JSPS KAKENHI Grant Number 26286072 and project for promoting Research Center in Meijo University.

Preparation of immobilized L-prolinamide via enzymatic polymerization of phenolic L-prolinamide and evaluation of its catalytic performance for direct asymmetric aldol reaction.

PubMed

Qu, Chengke; Zhao, Wenshan; Zhang, Lei; Cui, Yuanchen

2014-04-01

Phenolic L-prolinamide was allowed to participate in enzymatic polymerization with horseradish peroxidase as the catalyst, generating immobilized L-prolinamide. The catalytic performance of the resultant polymer-supported L-prolinamide for direct asymmetric aldol reaction between aromatic aldehyde and cyclohexanone was studied. The results show that as prepared L-prolinamide can catalyze the aldol reaction at room temperature in the presence of H2O. Relevant aldol addition products are obtained with good yields (up to 91%), high diastereoselectivities (up to 6:94 dr), and medium enantioselectivities (up to 87% ee). Moreover, the title polymer-supported catalyst can be recovered and reused for at least five cycles while the activity remains almost unchanged. Copyright © 2014 Wiley Periodicals, Inc.

Effects of NOx on the molecular composition of secondary organic aerosol formed by the ozonolysis and photooxidation of α-pinene

NASA Astrophysics Data System (ADS)

Park, Jun-Hyun; Babar, Zaeem Bin; Baek, Sun Jong; Kim, Hyun Sik; Lim, Ho-Jin

2017-10-01

The molecular composition of secondary organic aerosol (SOA), obtained from the ozonolysis and photooxidation of α-pinene, was investigated using ultrahigh-resolution Fourier transform-ion cyclotron resonance mass spectrometry (FT-ICR MS) in negative ion mode electrospray ionization (ESI). SOA formation was performed in an indoor smog chamber. The molecular formulae of individual species were identified on the basis of the measured ionic mass using guidelines, such as number of atoms, elemental ratios, and the nitrogen rule. In each of the SOAs obtained, 815-3501 monomeric and oligomeric (mainly dimeric) species were identified below m/z 800. From ozonolysis, mainly 95% of the typical oxygenated species (CHO) were detected, whereas from photooxidation under high NOx conditions, 32% of nitrogen-containing species (CHON) were detected. Several common intense species (e.g., C9H14O6, C10H14O6, C10H16O5, C17H26O7, C19H28O9, C10H15NO8, and C10H15NO9) could be listed as candidate tracers for the conventional tracers for α-pinene SOA. The increased percentage of CHON as a primary effect of NOx on the SOA composition evidently affected other physicochemical parameters, such as elemental ratios (i.e., O/C, H/C, and N/C), the double-bond equivalent (DBE), the carbon oxidation state (OSC), and the organic-mass-to-carbon ratio (OM/OC). The O/C and OM/OC for CHON were greater than those observed for CHO, indicating that nitrogen preferentially exists in the oxidized form (e.g., -ONO2). The complexity of oligomerization was observed in DBE and OM/OC according to the number of carbon atoms.

A novel organic–inorganic hybrid with Anderson type polyanions as building blocks: (C{sub 6}H{sub 10}N{sub 3}O{sub 2}){sub 2}Na(H{sub 2}O){sub 2}[Al(OH){sub 6}Mo{sub 6}O{sub 18}]·6H{sub 2}O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thabet, Safa, E-mail: safathabet@hotmail.fr; Ayed, Brahim, E-mail: brahimayed@yahoo.fr; Haddad, Amor

Graphical abstract: Display Omitted Highlights: ► Synthesis of a novel inorganic–organic hybrid compound based on Anderson polyoxomolybdates. ► Characterization by X-ray diffraction, IR and UV–Vis spectroscopies of the new compound. ► Potential applications in catalysis, biochemical analysis and electrical conductivity of the organic–inorganic compound. -- Abstract: A new organic–inorganic hybrid compound based on Anderson polyoxomolybdates, (C{sub 6}H{sub 10}N{sub 3}O{sub 2}){sub 2}Na(H{sub 2}O){sub 2}[Al(OH){sub 6}Mo{sub 6}O{sub 18}]·6H{sub 2}O (1) have been isolated by the conventional solution method and characterized by single-crystal X-ray diffraction, infrared, ultraviolet spectroscopy and Thermogravimetric Analysis (TGA). This compound crystallized in the triclinic system, space group P−1, withmore » a = 94.635(1) Å, b = 10.958(1) Å, c = 11.602(1) Å, α = 67.525(1)°, β = 71.049(1)°, γ = 70.124(1)° and Z = 1. The crystal structures of the compounds exhibit three-dimensional supramolecular assembly based on the extensive hydrogen bonding interactions between organic cations, sodium cations, water molecules and Anderson polyoxoanions. The infrared spectrum fully confirms the X-ray crystal structure and the UV spectrum of the title compound exhibits an absorption peak at 210 nm.« less

H2O activity in concentrated NaCl solutions at high pressures and temperatures measured by the brucite-periclase equilibrium

NASA Astrophysics Data System (ADS)

Aranovich, L. Y.; Newton, R. C.

1996-10-01

H2O activities in concentrated NaCl solutions were measured in the ranges 600° 900° C and 2 15 kbar and at NaCl concentrations up to halite saturation by depression of the brucite (Mg(OH)2) periclase (MgO) dehydration equilibrium. Experiments were made in internally heated Ar pressure apparatus at 2 and 4.2 kbar and in 1.91-cm-diameter piston-cylinder apparatus with NaCl pressure medium at 4.2, 7, 10 and 15 kbar. Fluid compositions in equilibrium with brucite and periclase were reversed to closures of less than 2 mol% by measuring weight changes after drying of punctured Pt capsules. Brucite-periclase equilibrium in the binary system was redetermined using coarsely crystalline synthetic brucite and periclase to inhibit back-reaction in quenching. These data lead to a linear expression for the standard Gibbs free energy of the brucite dehydration reaction in the experimental temperature range: ΔG° (±120J)=73418 134.95 T(K). Using this function as a baseline, the experimental dehydration points in the system MgO-H2O-NaCl lead to a simple systematic relationship of high-temperature H2O activity in NaCl solution. At low pressure and low fluid densities near 2 kbar the H2O activity is closely approximated by its mole fraction. At pressures of 10 kbar and greater, with fluid densities approaching those of condensed H2O, the H2O activity becomes nearly equal to the square of its mole fraction. Isobaric halite saturation points terminating the univariant brucite-periclase curves were determined at each experimental pressure. The five temperature-composition points in the system NaCl-H2O are in close agreement with the halite saturation curves (liquidus curves) given by existing data from differential thermal analysis to 6 kbar. Solubility of MgO in the vapor phase near halite saturation is much less than one mole percent and could not have influenced our determinations. Activity concentration relations in the experimental P-T range may be retrieved for the binary system H2O-NaCl from our brucite-periclase data and from halite liquidus data with minor extrapolation. At two kbar, solutions closely approach an ideal gas mixture, whereas at 10 kbar and above the solutions closely approximate an ideal fused salt mixture, where the activities of H2O and NaCl correspond to an ideal activity formulation. This profound pressure-induced change of state may be characterized by the activity ( a) concentration ( X) expression: a H 2O= X H 2O/(1+α X NaCl), and a NaCl=(1+α)(1+α)[ X NaCl/(1+α X NaCl)](1+α). The parameter α is determined by regression of the brucite-periclase H2O activity data: α=exp[A B/ϱH 2O ]-C P/ T, where A=4.226, B=2.9605, C=164.984, and P is in kbar, T is in Kelvins, and ϱH 2O is the density of H2O at given P and T in g/cm3. These formulas reproduce both the H2O activity data and the NaCl activity data with a standard deviation of ±0.010. The thermodynamic behavior of concentrated NaCl solutions at high temperature and pressure is thus much simpler than portrayed by extended Debye-Hückel theory. The low H2O activity at high pressures in concentrated supercritical NaCl solutions (or hydrosaline melts) indicates that such solutions should be feasible as chemically active fluids capable of coexisting with solid rocks and silicate liquids (and a CO2-rich vapor) in many processes of deep crustal and upper mantle metamorphism and metasomatism.

Electrochemical Investigations on Graphene and Lithium Phthalocyanine as Catalysts for Reversible Oxygen Reduction Reaction in Li-O2 Cells

DTIC Science & Technology

2015-05-11

maintained at 1:1. For the preparation of RGO-PPY composite, 1 ml pyrrole (Aldrich) was dissolved in 10 ml 0.1 M HCl and 100 mg RGO was added. The mixture...4 °C, and then added drop-wise to the suspension consisting of RGO and pyrrole . The contents were stirred for 6 h to facilitate the oxidation of... pyrrole to PPY. The RGO- PPY (weight ratio 1:1) composite was separated by centrifugation, washed repeatedly with water and finally with ethanol. It was

Genetic Exclusion in Bacteriophage T4.

DTIC Science & Technology

1987-01-01

1942) as "interference" between various coliphages , was shown by Delbruck and Bailey (1946) to be the inability of superinfecting phage to contribute... water : 5.8 g Na IPO , 3.0 2 4 g KH PO , 0.5 g NaCl, 1.0 g NH Cl, and the pH adjusted to 2 4 4 o 6.8 to 7.0. All media were autoclaved, cooled to 55 C...0.5M Tris), once with a 1:1 mixture of phenol and chloroform (1/24 isoamyl alcohol) then thrice iith an equal volume of water saturated ether. After

Fluid inclusion volatile analysis by gas chromatography with photoionization micro-thermal conductivity detectors: Applications to magmatic MoS 2 and other H 2O-CO 2 and H 2O-CH 4 fluids

NASA Astrophysics Data System (ADS)

Bray, C. J.; Spooner, E. T. C.

1992-01-01

Eighteen fluid inclusion volatile peaks have been detected and identified from 1-2 g samples (quartz) by gas chromatography using heated (~105°C) on-line crushing, helium carrier gas, a single porous polymer column (HayeSep R; 10' × 1/8″: 100/120#; Ni alloy tubing), two temperature programme conditions for separate sample aliquots, micro-thermal conductivity (TCD) and photoionization detectors (PID; 11.7 eV lamp), and off-line digital peak processing. In order of retention time these volatile peaks are: N 2, Ar, CO, CH 4, CO 2, C 2H 4, C 2H 6, C 2H 2, COS, C 3H 6, C 3H 8, C 3H 4 (propyne), H 2O (22.7 min at 80°C), SO 2, ± iso- C4H10 ± C4H8 (1-butene) ± CH3SH, C 4H 8 (iso-butylene), (?) C 4H 6 (1,3 butadiene) and ± n- C4H10 ± C4H8 (trans-2-butene) (80 and -70°C temperature programme conditions combined). H 2O is analysed directly. O 2 can be analysed cryogenically between N 2 and Ar, but has not been detected in natural samples to date in this study. H 2S, SO 2, NH 3, HCl, HCN, and H 2 ca nnot be analysed at present. Blanks determined by crushing heat-treated Brazilian quartz (800-900°C/4 h) are zero for 80°C temperature programme conditions, except for a large, unidentified peak at ~64 min, but contain H 2O, CO 2, and some low molecular weight hydrocarbons at -70°C temperature conditions due to cryogenic accumulation from the carrier gas and subsequent elution. TCD detection limits are ~30 ppm molar in inclusions; PID detection limits are ~ 1 ppm molar in inclusions and lower for unsaturated hydrocarbons (e.g., ~0.2 ppm for C 2H 4; ~ 1 ppb for C 2H 2; ~0.3 ppb for C 3H 6). Precisions (1σ) are ~ ±1-2% and ~ ± 13% for H 2O in terms of total moles detected; the latter value is equivalent to ±0.6 mol% at the 95 mol% H 2O level. Major fluid inclusion volatile species have been successfully analysed on a ~50 mg fluid inclusion section chip (~7 mm × ~10 mm × ~100 μm). Initial inclusion volatile analyses of fluids of interpreted magmatic origin from the Cretaceous Boss Mtn. monzogranite stock-related MoS 2 deposit, central British Columbia of ~97 mol% H 2O, ~3% CO 2, ~ 140-150 ppm N 2, and ~16-39 ppm CH 4 (~300-350°C) are reasonable in comparison with high temperature (~400-900°C) volcanic gas analyses from four, active calc-alkaline volcanoes; e.g., the H 2O contents of volcanic gases from the White Island (New Zealand), Mount St. Helens (Washington, USA), Merapi (Bali, Indonesia), and Momotombo (Nicaragua) volcanoes are 88-95%, >90% (often >95%), 88-95% and ~93%, respectively; CO 2 contents are ~3-10%, 1-10%, 3-8%, and ~3.5%. CO 2/N 2 ratios for the Boss Mtn. MoS 2 fluids of ~ 190-220 are in the range for known volcanic gas ratios (e.g., ~ 150- 240; White Island). The ∑S content of the Boss Mtn. MoS 2 fluid prior to S loss by sulphide precipitation may have been ~2 mol% since CO 2/∑S molar ratios of analysed high-temperature volcanic gases are ~ 1.5. This estimate is supported by ∑S contents for White Island, Merapi and Momotombo volcanic gases of ~2%, ~0.5-2.5%, and ~2%. COS has been determined in H 2O-CO 2 fluid inclusions of interpreted magmatic origin from the Boss Mtn. MoS 2 deposit and the Tanco zoned granitic pegmatite, S.E. Manitoba at ~50-100 ppm molar levels, which are consistent with levels in volcanic gases. It appears that low, but significant, concentrations of C 2-C 4 alkanes (~ 1-20 ppm), C 2-C 4 alkenes (~ 1-480 ppb) and alkynes (e.g., C 3H 4) have been detected in magmatically derived fluids (Boss Mtn. MoS 2 deposit; Tanco granitic pegmatite). Significantly higher, low molecular weight hydrocarbon concentrations have been determined in a CH 4-rich (~ 2%), externally derived fluid of possible metamorphic or deep crustal origin trapped as inclusions in metasomatic wall-rock tourmaline adjacent to the Tanco pegmatite (e.g., 300/470 ppm C 2H 6; 50/90 ppm C 3H 8; 3-60 ppm C 2H 4/C 3H 6 n-C 4H 10).

Calculation of the Standard Molal Thermodynamic Properties of Crystalline, Liquid, and Gas Organic Molecules at High Temperatures and Pressures

NASA Astrophysics Data System (ADS)

Helgeson, Harold C.; Owens, Christine E.; Knox, Annette M.; Richard, Laurent

1998-03-01

Calculation of the thermodynamic properties of organic solids, liquids, and gases at high temperatures and pressures is a requisite for characterizing hydrothermal metastable equilibrium states involving these species and quantifying the chemical affinities of irreversible reactions of organic molecules in natural gas, crude oil, kerogen, and coal with minerals and organic, inorganic, and biomolecular aqueous species in interstitial waters in sedimentary basins. To facilitate calculations of this kind, coefficients for the Parameters From Group Contributions (PFGC) equation of state have been compiled for a variety of groups in organic liquids and gases. In addition, molecular weights, critical temperatures and pressures, densities at 25°C and 1 bar, transition, melting, and boiling temperatures ( Tt,Pr, Tm,Pr, and Tv,Pr, respectively) and standard molal enthalpies of transition (Δ H° t,Pr), melting (Δ H° m,Pr), and vaporization (Δ H° v,Pr) of organic species at 1 bar ( Pr) have been tabulated, together with an internally consistent and comprehensive set of standard molal Gibbs free energies and enthalpies of formation from the elements in their stable state at 298.15 K ( Tr) and Pr (Δ G° f and Δ H° f, respectively). The critical compilation also includes standard molal entropies ( S°) and volumes ( V°) at Tr and Pr, and standard molal heat capacity power function coefficients to compute the standard molal thermodynamic properties of organic solids, liquids, and gases as a function of temperature at 1 bar. These properties and coefficients have been tabulated for more than 500 crystalline solids, liquids, and gases, and those for many more can be computed from the equations of state group additivity algorithms. The crystalline species correspond to normal alkanes (C nH 2( n+1) ) with carbon numbers ( n, which is equal to the number of moles of carbon atoms in one mole of the species) ranging from 5 to 100, and 23 amino acids including glycine (C 2H 5NO 2), alanine (C 3H 7NO 2), valine (C 5H 11NO 2), leucine (C 6H 13NO 2), isoleucine (C 6H 13NO 2), aspartic acid (C 4H 7NO 4), glutamic acid (C 5H 9NO 4), asparagine (C 4H 8N 2O 3), glutamine (C 5H 10N 2O 3), proline (C 5H 9NO 2), phenylalanine (C 9H 11NO 2), tryptophan (C 11H 12N 2O 2), methionine (C 5H 11SNO 2), serine (C 3H 7NO 3), threonine (C 4H 9NO 3), cysteine (C 3H 7SNO 2), tyrosine (C 9H 11NO 3), lysine (C 6H 14N 2O 2), lysine:HCl (C 6H 15N 2O 2Cl), arginine (C 6H 14N 4O 2), arginine:HCl (C 6H 15N 4O 2Cl), histidine (C 6H 9N 3O 2), and histidine:HCl (C 6H 10N 3O 2Cl). The data for the latter compounds permit calculation of the standard molal thermodynamic properties of protein unfolding in biogeochemical processes (Helgeson et al 1998). The liquids and gases considered in the present study include normal alkanes (C nH 2( n+1) ) for carbon numbers ranging from 1 to 100, 2- and 3-methylalkanes (C nH 2( n+1) ) for 4 ≤ n ≤ 20 and 6 ≤ n ≤ 20, respectively, 2,3-dimethylpentane (C 7H 16), 4-methylheptane (C 8H 18), cycloalkanes (C nH 2 n) for 3 ≤ n ≤ 8, methylated benzenes (C nH 2( n-3) ) for 7 ≤ n ≤ 12, normal alkylbenzenes (C nH 2( n-3) ) for 6 ≤ n ≤ 20, normal 1-alcohols (C nH 2( n+1) O) for 1 ≤ n ≤ 20, ethylene glycol (C 2H 6O 2), glycerol (C 3H 8O 3), normal 1-alkanethiols (C nH 2( n+1) S) for 1 ≤ n ≤ 20, normal carboxylic acids (C nH 2 nO 2) for 2 ≤ n ≤ 20, and the following miscellaneous species: 2-thiabutane (C 3H 8S), thiophene (C 4H 4S), thiophenol (C 6H 6S), acetone (C 3H 6O), 2-butanone (C 4H 8O), ethyl acetate (C 4H 8O 2), pyridine (C 5H 5N), 3-methylpyridine (C 6H 7N), and quinoline (C 9H 7N). One additional liquid (2-methylthiacyclopentane (C 5H 10S)) was also considered along with crystalline and gaseous carbazole (C 12H 9N). The thermodynamic data and equations summarized below can be used together with the standard molal thermodynamic properties of high molecular weight organic compounds ( Richard and Helgeson 1995, Richard and Helgeson 1998a, Richard and Helgeson 1998b) and minerals, inorganic gases, and aqueous species, including biomolecules ( Johnson et al 1992; Shock 1992a, Shock 1994, Shock 1995; Shock et al 1997; Shock and Koretsky 1993, Shock and Koretsky 1995; Sassani and Shock 1992, Sassani and Shock 1994; Schulte and Shock 1993, Schulte and Shock 1995; Oelkers et al 1995; Amend and Helgeson 1997a, Amend and Helgeson 1997b, Amend and Helgeson 1997c, Amend and Helgeson 1998; Sverjensky et al 1997) to compute equilibrium constants and chemical affinities for a wide variety of organic-inorganic reactions in geochemical and biochemical processes at both high and low temperatures and pressures. Unless indicated otherwise, all amino acid designations in the present communication refer to the L-α form.

Series of mixed uranyl-lanthanide (Ce, Nd) organic coordination polymers with aromatic polycarboxylates linkers.

PubMed

Mihalcea, Ionut; Volkringer, Christophe; Henry, Natacha; Loiseau, Thierry

2012-09-17

Three series of mixed uranyl-lanthanide (Ce or Nd) carboxylate coordination polymers have been successfully synthesized by means of a hydrothermal route using either conventional or microwave heating methods. These compounds have been prepared from mixtures of uranyl nitrate, lanthanide nitrate together with phthalic acid (1,2), pyromellitic acid (3,4), or mellitic acid (5,6) in aqueous solution. The X-ray diffraction (XRD) single-crystal revealed that the phthalate complex (UO(2))(4)O(2)Ln(H(2)O)(7)(1,2-bdc)(4)·NH(4)·xH(2)O (Ln = Ce(1), Nd(2); x = 1 for 1, x = 0 for 2), is based on the connection of tetranuclear uranyl-centered building blocks linked to discrete monomeric units LnO(2)(H(2)O)(7) via the organic species to generate infinite chains, intercalated by free ammonium cations. The pyromellitate phase (UO(2))(3)Ln(2)(H(2)O)(12)(btec)(3)·5H(2)O (Ce(3), Nd(4)) contains layers of monomeric uranyl-centered hexagonal and pentagonal bipyramids linked via the carboxylate arms of the organic molecules. The three-dimensionality of the structure is ensured by the connection of remaining free carboxylate groups with isolated monomeric units LnO(2)(H(2)O)(7). The network of the third series (UO(2))(2)(OH)Ln(H(2)O)(7)(mel)·5H(2)O (Ce(5), Nd(6)) is built up from dinuclear uranyl units forming layers through connection with the mellitate ligands, which are further linked to each other through discrete monomers LnO(3)(H(2)O)(6). The thermal decomposition of the various coordination complexes led to the formation of mixed uranium-lanthanide oxide, with the fluorite-type structure at 1500 °C (for 1, 2) or 1400 °C for 3-6. Expected U/Ln ratio from the crystal structures were observed for compounds 1-6.

Paralinear Oxidation of CVD SiC in Simulated Fuel-Rich Combustion

NASA Technical Reports Server (NTRS)

Fox, Dennis S.; Opila, Elizabeth J.; Hann, Raiford E.

2000-01-01

The oxidation kinetics of CVD SiC were measured by thermogravimetric analysis (TGA) in a 4H2 (central dot) 12H2O (central dot) 10CO (central dot) 7CO2 (central dot) 67N2 gas mixture flowing at 0.44 cm/s at temperatures between 1300 and 1450 C in fused quartz furnace tubes at I atm total pressure. The SiC was oxidized to form solid SiO2. At less than or = 1350 C, the SiO2 was in turn volatilized. Volatilization kinetics were consistent with the thermodynamic predictions based on SiO formation. These two simultaneous reactions resulted in overall paralinear kinetics. A curve fitting technique was used to determine the linear and parabolic rate constants from the paralinear kinetic data. Volatilization of the protective SiO2 scale resulted in accelerated consumption of SiC. Recession rates under conditions more representative of actual combustors were estimated from the furnace data.

[Polymerase chain reaction (PCR) for the identification of toxigenic Vibrio cholerae O1 in oysters].

PubMed

Rodríguez-Angeles, M G; Giono-Cerezo, S; Moreno-Escobar, A; Valdespino-Gómez, J L

1994-01-01

PCR was made with ctx2 (CGG GCA GAT TCT AGA CCT CCT G) y ctx3 (CGA TGA TCT TGG AGC ATT CCC AC) primers for subunit A of cholera toxin, 30 cycles of temperature on samples of 50 g of oysters added in 450 ml of peptone alcaline water that were inoculated with 15 x 10(6), 0.75 x 10(6) and 0.15 x 10(6) CFU/ml of toxigenic 6707 V. cholerae O1 reference strain. The samples were tested by three microbiological methods: INDRE's method uses 1 x 10(-1) dilution of sample, two fold pass to peptone alcaline water pH 9 incubated 18 h and 6 h at 37 degrees C, the Food and Drugs Administration (FDA) method uses 10(-1) to 10(-6) dilutions of sample, 6 h incubation and reincubation for 18 h at 37 and 42 degrees C and the Mexican laboratories (LMD) with 10(-4) to 10(-3) dilutions, the samples were incubated for 6 h and then reincubated for 18 h at two temperatures 37 and 42 degrees C. The PCR by INDRE's method was positive with 3 x 10(2) CFU/ml/g oyster. In the FDA's method the PCR detected DNA in 10(-4) dilution with 3 x 10(1) CFU/ml/g oyster and in LMD's method the PCR was positive in 10(-3) with 3 CFU/ml/g oyster. The results of the PCR were obtained between 5-6 h, and later V. cholerae O1 was isolated by three microbiological methods. The PCR reproducibility was better on DNA sample diluted 1:4 and 10 microliters of sample increased from 1:1000 to 1:10000 the sensitivity of PCR.

Corrosion testing of zirconia, beryllia and magnesia ceramics in molten alkali metal carbonates at 900 °C

NASA Astrophysics Data System (ADS)

Kaplan, Valery; Bendikov, Tatyana; Feldman, Yishay; Gartsman, Konstantin; Wachtel, Ellen; Lubomirsky, Igor

2016-01-01

An electrochemical cell containing molten Li2CO3-Li2O at 900 °C has been proposed for the conversion of the greenhouse gas CO2 to CO for chemical energy storage. In the current work, we have examined the corrosion resistance of zirconia, beryllia and magnesia ceramics at 900 °C in the Li2CO3-Li2O and Li-Na-K carbonate eutectic mixtures to identify suitable electrically insulating materials. Conclusions regarding material stability were based on elemental analysis of the melt, primarily via X-ray photoelectron spectroscopy, a particularly sensitive technique. It was found that magnesia is completely stable for at least 33 h in a Li2CO3-Li2O melt, while a combined lithium titanate/lithium zirconate layer forms on the zirconia ceramic as detected by XRD. Under the same melt conditions, beryllia shows considerable leaching into solution. In a Li-Na-K carbonate eutectic mixture containing 10.2 mol% oxide at 900 °C under standard atmospheric conditions, magnesia showed no signs of degradation. Stabilization of the zirconia content of the eutectic mixture at 0.01-0.02 at% after 2 h is explained by the formation of a lithium zirconate coating on the ceramic. On the basis of these results, we conclude that only magnesia can be satisfactorily used as an insulating material in electrolysis cells containing Li2CO3-Li2O melts.

Isolation, pharmacological activity and structure determination of physalin B and 5β,6β-epoxyphysalin B isolated from Congolese Physalis angulata L.

PubMed

Mangwala Kimpende, Peter; Lusakibanza, Mariano; Mesia, Kahunu; Tona, Lutete; Tits, Monique; Angenot, Luc; Frédérich, Michel; Van Meervelt, Luc

2013-12-15

Physalis angulata L., an annual herb from the Solanaceae family, is widely used in popular medicine in tropical countries to treat a variety of diseases. Two products, (X) and (Y), were isolated from a crude CH2Cl2 extract of dried Congolese Physalis angulata L. plants and crystallized from acetone for structure elucidation. Compound (X) corresponds to a physalin B dimer acetone solvate hydrate (2C28H30O9·C3H6O·0.22H2O), while compound (Y) crystallizes as a mixed crystal containing two physalin B molecules which overlap with 5β,6β-epoxyphysalin B, also known as physalin F, and one acetone molecule in the asymmetric unit (1.332C28H30O9·0.668C28H30O10·C3H6O). Antiplasmodial activity, cytotoxic activity and selectivity indices were determined for crude extracts and the two isolated products (X) and (Y).

Supra-molecular architecture in a co-crystal of the N(7)-H tautomeric form of N (6)-benzoyl-adenine with adipic acid (1/0.5).

PubMed

Swinton Darious, Robert; Thomas Muthiah, Packianathan; Perdih, Franc

2016-06-01

The asymmetric unit of the title co-crystal, C12H9N5O·0.5C6H10O4, consists of one mol-ecule of N (6)-benzoyl-adenine (BA) and one half-mol-ecule of adipic acid (AA), the other half being generated by inversion symmetry. The dihedral angle between the adenine and phenyl ring planes is 26.71 (7)°. The N (6)-benzoyl-adenine mol-ecule crystallizes in the N(7)-H tautomeric form with three non-protonated N atoms. This tautomeric form is stabilized by intra-molecular N-H⋯O hydrogen bonding between the carbonyl (C=O) group and the N(7)-H hydrogen atom on the Hoogsteen face of the purine ring, forming an S(7) ring motif. The two carboxyl groups of adipic acid inter-act with the Watson-Crick face of the BA mol-ecules through O-H⋯N and N-H⋯O hydrogen bonds, generating an R 2 (2)(8) ring motif. The latter units are linked by N-H⋯N hydrogen bonds, forming layers parallel to (10-5). A weak C-H⋯O hydrogen bond is also present, linking adipic acid mol-ecules in neighbouring layers, enclosing R (2) 2(10) ring motifs and forming a three-dimensional structure. C=O⋯π and C-H⋯π inter-actions are also present in the structure.

Selective synthesis and characterization of single-crystal silver molybdate/tungstate nanowires by a hydrothermal process.

PubMed

Cui, Xianjin; Yu, Shu-Hong; Li, Lingling; Biao, Liu; Li, Huabin; Mo, Maosong; Liu, Xian-Ming

2004-01-05

Selective synthesis of uniform single crystalline silver molybdate/tungstate nanorods/nanowires in large scale can be easily realized by a facile hydrothermal recrystallization technique. The synthesis is strongly dependent on the pH conditions, temperature, and reaction time. The phase transformation was examined in details. Pure Ag(2)MoO(4) and Ag(6)Mo(10)O(33) can be easily obtained under neutral condition and pH 2, respectively, whereas other mixed phases of Mo(17)O(47), Ag(2)Mo(2)O(7,) Ag(6)Mo(10)O(33) were observed under different pH conditions. Ag(6)Mo(10)O(33) nanowires with uniform diameter 50-60 nm and length up to several hundred micrometers were synthesized in large scale for the first time at 140 degrees C. The melting point of Ag(6)Mo(10)O(33) nanowires were found to be about 238 degrees C. Similarly, Ag(2)WO(4), and Ag(2)W(2)O(7) nanorods/nanowires can be selectively synthesized by controlling pH value. The results demonstrated that this route could be a potential mild way to selectively synthesize various molybdate nanowires with various phases in large scale.

Experimental and theoretical study of the reactions between neutral vanadium oxide clusters and ethane, ethylene, and acetylene.

PubMed

Dong, Feng; Heinbuch, Scott; Xie, Yan; Rocca, Jorge J; Bernstein, Elliot R; Wang, Zhe-Chen; Deng, Ke; He, Sheng-Gui

2008-02-13

Reactions of neutral vanadium oxide clusters with small hydrocarbons, namely C2H6, C2H4, and C2H2, are investigated by experiment and density functional theory (DFT) calculations. Single photon ionization through extreme ultraviolet (EUV, 46.9 nm, 26.5 eV) and vacuum ultraviolet (VUV, 118 nm, 10.5 eV) lasers is used to detect neutral cluster distributions and reaction products. The most stable vanadium oxide clusters VO2, V2O5, V3O7, V4O10, etc. tend to associate with C2H4 generating products V(m)O(n)C2H4. Oxygen-rich clusters VO3(V2O5)(n=0,1,2...), (e.g., VO3, V3O8, and V5O13) react with C2H4 molecules to cause a cleavage of the C=C bond of C2H4 to produce (V2O5)(n)VO2CH2 clusters. For the reactions of vanadium oxide clusters (V(m)O(n)) with C2H2 molecules, V(m)O(n)C2H2 are assigned as the major products of the association reactions. Additionally, a dehydration reaction for VO3 + C2H2 to produce VO2C2 is also identified. C2H6 molecules are quite stable toward reaction with neutral vanadium oxide clusters. Density functional theory calculations are employed to investigate association reactions for V2O5 + C2H(x). The observed relative reactivity of C2 hydrocarbons toward neutral vanadium oxide clusters is well interpreted by using the DFT calculated binding energies. DFT calculations of the pathways for VO3+C2H4 and VO3+C2H2 reaction systems indicate that the reactions VO3+C2H4 --> VO2CH2 + H2CO and VO3+C2H2 --> VO2C2 + H2O are thermodynamically favorable and overall barrierless at room temperature, in good agreement with the experimental observations.

Studying the internal ballistics of a combustion-driven potato cannon using high-speed video

NASA Astrophysics Data System (ADS)

Courtney, E. D. S.; Courtney, M. W.

2013-07-01

A potato cannon was designed to accommodate several different experimental propellants and have a transparent barrel so the movement of the projectile could be recorded on high-speed video (at 2000 frames per second). Five experimental propellants were tested: propane (C3H8), acetylene (C2H2), ethanol (C2H6O), methanol (CH4O) and butane (C4H10). The quantity of each experimental propellant was calculated to approximate a stoichometric mixture and considering the upper and lower flammability limits, which in turn were affected by the volume of the combustion chamber. Cylindrical projectiles were cut from raw potatoes so that there was an airtight fit, and each weighed 50 (± 0.5) g. For each trial, position as a function of time was determined via frame-by-frame analysis. Five trials were made for each experimental propellant and the results analyzed to compute velocity and acceleration as functions of time. Additional quantities, including force on the potato and the pressure applied to the potato, were also computed. For each experimental propellant average velocity versus barrel position curves were plotted. The most effective experimental propellant was defined as that which accelerated the potato to the highest muzzle velocity. The experimental propellant acetylene performed the best on average (138.1 m s-1), followed by methanol (48.2 m s-1), butane (34.6 m s-1), ethanol (33.3 m s-1) and propane (27.9 m s-1), respectively.

Electrochemical characterisations and ageing of ionic liquid/γ-butyrolactone mixtures as electrolytes for supercapacitor applications over a wide temperature range

NASA Astrophysics Data System (ADS)

Dagousset, Laure; Pognon, Grégory; Nguyen, Giao T. M.; Vidal, Frédéric; Jus, Sébastien; Aubert, Pierre-Henri

2017-08-01

Electrochemical properties in mesoporous media of three different ionic liquids (1-propyl-1-methylpyrrolidinium-bis(fluorosulfonyl)imide - Pyr13FSI, 1-butyl-1-methylpyrrolidinium-bis(trifluoromethanesulfonyl)imide - Pyr14TFSI and 1-ethyl-3-methylimidazolium-bis(trifluoromethanesulfonyl)imide - EMITFSI) are investigated from -50 °C to 100 °C and compared with binary mixtures with γ-butyrolactone (GBL). Buckypaper composed of Single-Wall Carbon Nanotubes (SWCNTs) are used to prepare and study coin-cell supercapacitors. Supercapacitor using Pyr13FSI/GBL present a rapid loss of capacitance after only a thousand cycles at 100 °C. On the contrary, EMITFSI/GBL and Pyr14TFSI/GBL prove to be very promising at high temperature (the capacitance loss after 10,000 cycles is 9% and 10%). More drastic ageing tests such as floating are also carried out for these two mixtures at 100 °C and -50 °C. 23% and 15% capacitance losses have been recorded after 500 h of floating at 100 °C for EMITFSI/GBL and Pyr14TFSI/GBL. The capacitance of supercapacitors based on Pyr14TFSI/GBL dropped by 20% after 200 h of floating at -50 °C rather than EMITFSI/GBL show a remarkable stability during floating at -50 °C, with 6.6% capacitance loss after 500 h (3 V at -50 °C). These results show that the mixture EMITFSI/GBL works properly all along the broad range of temperature [-50 °C to +100 °C] and thus proved that our approach is very promising for the development of high performances supercapacitors specifically adapted for extreme environment.

Crystal chemistry of thorium nitrates and chromates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sigmon, Ginger E.; Burns, Peter C., E-mail: pburns@nd.ed

2010-07-15

The structures and infrared spectra of six novel thorium compounds are reported. Th(NO{sub 3}){sub 2}(OH){sub 2}(H{sub 2}O){sub 2} (1) crystallizes in space group C2/c, a=14.050(1), b=8.992(7), c=5.954(5) A, {beta}=101.014(2){sup o}. K{sub 2}Th(NO{sub 3}){sub 6} (2), P-3, a=13.606(1), c=6.641(6) A. (C{sub 12}H{sub 28}N){sub 2}Th(NO{sub 3}){sub 6} (3), P2{sub 1}/c, a=14.643(4), b=15.772(5), c=22.316(5) A, {beta}=131.01(1){sup o}. KTh(NO{sub 3}){sub 5}(H{sub 2}O){sub 2} (4), P2{sub 1}/c, a=10.070(8), b=12.731(9), c=13.231(8) A, {beta}=128.647(4){sup o}. Th(CrO{sub 4}){sub 2}(H{sub 2}O){sub 2} (5), P2{sub 1}/n, a=12.731(1), b=9.469(8), c=12.972(1) A, {beta}=91.793(2){sup o}. K{sub 2}Th{sub 3}(CrO{sub 4}){sub 7}(H{sub 2}O){sub 10} (6), Ama2, a=19.302(8), b=15.580(6), c=11.318(6) A. The coordination polyhedra about Thmore » in these structures are diverse. Th is coordinated by 9 O atoms in 5 and 6, seven of which are from monodentate (CrO{sub 4}) tetrahedra and two are (H{sub 2}O). The Th in compound 1 is coordinated by ten O atoms, four of which are O atoms of two bidentate (NO{sub 3}) triangles and six of which are (OH) and (H{sub 2}O). In compounds 2, 3 and 4 the Th is coordinate by 12 O atoms. In 2 and 3 there are six bidentate (NO{sub 3}) triangles, and in 4 ten of the O atoms are part of five bidentate (NO{sub 3}) triangles and the others are (H{sub 2}O) groups. The structural units of these compounds consist of a chain of thorium and nitrate polyhedra (1), isolated thorium hexanitrate clusters (2, 3), an isolated thorium pentanitrate dihydrate cluster (4), and a sheet (6) and framework (5) of thorium and chromate polyhedra. These structures illustrate the complexity inherent in the crystal chemistry of Th. - Graphical Abstract: The structures and infrared spectra of four new Th nitrates and two Th chromates are reported. The coordination numbers of the Th cations range from nine to 12 in these compounds. Structural units consist of isolated clusters, chains, sheets and frameworks.« less

Cyclic Oxidation Behavior and Durability of ODS-FeCrAl Alloys in H2O and CO2 rich environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dryepondt, Sebastien N; Pint, Bruce A

Cyclic oxidation testing was conducted at 1200 C in O2, dry air and in atmospheres rich in H2O and/or CO2 to simulate combustion environments. The oxidation rates were significantly higher in air + 10%H2O and a mixture of O2-buffered 50%H2O-50%CO2, leading to shorter times to breakaway oxidation. Curve fitting using the COSP cyclic oxidation program confirmed that the presence of H2O results in an increase of the alumina spallation rate. The use of specimen mass gain modeling associated with the characterization of pre-oxidized specimens and in particular the determination of the remaining Al content after exposure, will allow to accuratelymore » estimate the durability of oxide dispersion-strengthened (ODS) FeCrAl alloys in combustion environments.« less

Dollar Summary of Federal Supply Classification and Service Category by Company, FY 87. Part 10. 5955-6650

DTIC Science & Technology

1987-01-01

0 9 LA- I 4 n * f6 IM Iý 4 m0 n -6 .4 M I4NO *0 0 C’ M VM0 tCJOP # 0 m v O a- 0 .4 -4 .4 -4 . -4 -4 .4 in 4 64 I -C6I *- 1 a 1- .0 6 1- V)f if. U...0H 0 xc w 0 W co <H Q4 Q- 0 C) 1 0 WU 0 1 H W IL < H w) Wj <) 4 1.- 0 H acca ~ cc xa 4 H H c .4 4)I c 0 I-H na zc cc 1- 40 m-c c IQ01 Z ZH 0 O w 0- a

Magneto-optical investigation of MgSO3·6H2O with polarized light

NASA Astrophysics Data System (ADS)

Petkova, P.

2017-10-01

The crystals of magnesium sulphite hexahydrate (MgSO3·6H2O) belong to point group C3 (no center of symmetry). They possess gyrotropy and nonlinear optical properties. The refractive index no and ne, the angle of Faraday rotation φ(λ), the Verdet constant V(λ), the magneto-optic anomaly factor γ(λ) and the density of oscillators N of MgSO3·6H2O single crystals have been studied in the present work. The investigations were carried out in the spectral range 300 - 800 nm with linear polarized light E ⃗ ⊥ c ̅ , E ⃗ | | c ̅ (c ̅ is the optical axis of MgSO3·6H2O) propagated in the direction (10 1 ̅ 0) .

Do group 1 metal salts form deep eutectic solvents?

PubMed

Abbott, A P; D'Agostino, C; Davis, S J; Gladden, L F; Mantle, M D

2016-09-14

Mixtures of metal salts such as ZnCl 2 , AlCl 3 and CrCl 3 ·6H 2 O form eutectic mixtures with complexing agents, such as urea. The aim of this research was to see if alkali metal salts also formed eutectics in the same way. It is shown that only a limited number of sodium salts form homogeneous liquids at ambient temperatures and then only with glycerol. None of these mixtures showed eutectic behaviour but the liquids showed the physical properties similar to the group of mixtures classified as deep eutectic solvents. This study focussed on four sodium salts: NaBr, NaOAc, NaOAc·3H 2 O and Na 2 B 4 O 7 ·10H 2 O. The ionic conductivity and viscosity of these salts with glycerol were studied, and it was found that unlike previous studies of quaternary ammonium salts with glycerol, where the salt decreased the viscosity, most of the sodium salts increased the viscosity. This suggests that sodium salts have a structure making effect on glycerol. This phenomenon is probably due to the high charge density of Na + , which coordinates to the glycerol. 1 H and 23 Na NMR diffusion and relaxation methods have been used to understand the molecular dynamics in the glycerol-salt mixtures, and probe the effect of water on some of these systems. The results reveal a complex dynamic behaviour of the different species within these liquids. Generally, the translational dynamics of the 1 H species, probed by means of PFG NMR diffusion coefficients, is in line with the viscosity of these liquids. However, 1 H and 23 Na T 1 relaxation measurements suggest that the Na-containing species also play a crucial role in the structure of the liquids.

Synthesis, structural characterization, and electrochemical properties of dinuclear Ni/Mn model complexes for the active site of [NiFe]-hydrogenases.

PubMed

Song, Li-Cheng; Li, Jia-Peng; Xie, Zhao-Jun; Song, Hai-Bin

2013-10-07

Four new dinuclear Ni/Mn model complexes RN(PPh2)2Ni(μ-SEt)2(μ-Cl)Mn(CO)3 (7, R = p-MeC6H4CH2; 8, R = EtO2CCH2) and RN(PPh2)2Ni(μ-SEt)2(μ-Br)Mn(CO)3 (9, R = p-MeC6H4CH2; 10, R = EtO2CCH2) have been prepared via the four separated step-reactions involving six new precursors RN(PPh2)2 (1, R = p-MeC6H4CH2; 2, R = EtO2CCH2), RN(PPh2)2NiCl2 (3, R = p-MeC6H4CH2; 4, R = EtO2CCH2), and RN(PPh2)2Ni(SEt)2 (5, R = p-MeC6H4CH2; 6, R = EtO2CCH2). The Et3N-assisted aminolysis of Ph2PCl with p-MeC6H4CH2NH2 or EtO2CCH2NH2·HCl in CH2Cl2 gave the azadiphosphine ligands 1 and 2 in 38% and 53% yields, whereas the coordination reaction of 1 or 2 with NiCl2·6H2O in CH2Cl2/MeOH afforded the mononuclear Ni dichloride complexes 3 and 4 in 59% and 78% yields, respectively. While thiolysis of 3 or 4 with EtSH under the assistance of Et3N in CH2Cl2 produced the mononuclear Ni dithiolate complexes 5 and 6 in 64% and 68% yields, further treatment of 5 and 6 with Mn(CO)5Cl or Mn(CO)5Br resulted in formation of the dinuclear Ni/Mn model complexes 7-10 in 31-73% yields. All the new compounds 1-10 have been structurally characterized, while model complexes 7 and 9 have been found to be catalysts for HOAc proton reduction to hydrogen under CV conditions.

Geochemical transformations and modeling of two deep-well injected hazardous wastes

USGS Publications Warehouse

Roy, W.R.; Seyler, B.; Steele, J.D.; Mravik, S.C.; Moore, D.M.; Krapac, I.G.; Peden, J.M.; Griffin, R.A.

1991-01-01

Two liquid hazardous wastes (an alkaline brine-like solution and a dilute acidic waste) were mixed with finely ground rock samples of three injection-related lithologies (sandstone, dolomite, and siltstone) for 155 to 230 days at 325??K-10.8 MPa. The pH and inorganic chemical composition of the alkaline waste were not significantly altered by any of the rock samples after 230 days of mixing. The acidic waste was neutralized as a consequence of carbonate dissolution, ion exchange, or clay-mineral dissolution, and hence was transformed into a nonhazardous waste. Mixing the alkaline waste with the solid phases yielded several reaction products: brucite, Mg(OH)2; calcite, CaCO3; and possibly a type of sodium metasilicate. Clay-like minerals formed in the sandstone, and hydrotalcite, Mg6Al2-CO3(OH)16??4H2O, may have formed in the siltstone at trace levels. Mixing the alkaline waste with a synthetic brine yielded brucite, calcite, and whewellite (CaC2O4??H2O). The thermodynamic model PHRQPITZ predicted that brucite and calcite would precipitate from solution in the dolomite and siltstone mixtures and in the alkaline waste-brine system. The dilute acidic waste did not significantly alter the mineralogical composition of the three rock types after 155 days of contact. The model PHREEQE indicated that the calcite was thermodynamically stable in the dolomite and siltstone mixtures.

Microstructures and Properties of the C/Zr-O-Si-C Composites Fabricated by Polymer Infiltration and Pyrolysis

NASA Astrophysics Data System (ADS)

Ma, Yan; Chen, Zhaohui

2013-09-01

A way to improve the ablation properties of the C/SiC composites in an oxyacetylene torch environment was investigated by the precursor infiltration and pyrolysis route using three organic precursors (zirconium butoxide, polycarbosilane, and divinylbenzene). The ceramic matrix derived from the precursors at 1200 °C was mainly a mixture of SiC, ZrO2, and C. After annealing at 1600 °C for 1 h, ZrO2 partly transformed to ZrC because of the carbothermic reductions and completely transformed to ZrC at 1800 °C in 1 h. The mechanical properties of the composites decreased with increasing temperature, while the ablation resistance increased due to the increasing content of ZrC. Compared with C/SiC composites, the ablation resistance of the C/Zr-O-Si-C composites overwhelms because of the oxide films which formed on the ablation surfaces. And, the films were composed of two layers: the porous surface layer (the mixture of ZrO2 and SiO2) and the dense underlayer (SiO2).

Separations method for polar molecules

DOEpatents

Thoma, Steven G.; Bonhomme, Francois R.

2004-07-27

A method for separating at least one compound from a liquid mixture containing different compounds where anew crystalline manganese phosphate composition with the formula Mn.sub.3 (PO.sub.4).sub.4.2(H.sub.3 NCH.sub.2 CH.sub.2).sub.3 N.6(H.sub.2 O) is dispersed in the liquid mixture, selectively intercalating one or more compounds into the crystalline structure of the Mn.sub.3 (PO.sub.4).sub.4.2(H.sub.3 NCH.sub.2 CH.sub.2).sub.3 N.6(H.sub.2 O).

Coordination-organometallic hybrid materials based on the trinuclear M(II)-Ru(II) (M=Ni and Zn) complexes: Synthesis, structural characterization, luminescence and electrochemical properties

NASA Astrophysics Data System (ADS)

Pawal, S. B.; Lolage, S. R.; Chavan, S. S.

2018-02-01

A new series of trinuclear complexes of the type Ni[R-C6H4Ndbnd CH(O)C6H3Ctbnd CRu(dppe)2Cl]2 (1a-c) and Zn[Rsbnd C6H4Ndbnd CH(O)C6H3Ctbnd CRu(dppe)2Cl]2 (2a-c) have been prepared from the reaction of trans-[RuCl(dppe)2Ctbnd Csbnd C6H3(OH)(CHO)] (1) with aniline, 4-nitroaniline and 4-methoxyaniline (R1-3) in presence of nickel acetate and zinc acetate in CH2Cl2/MeOH (1:1) mixture. The structural properties of the complexes have been characterized by elemental analyses and spectroscopic techniques viz. FTIR, UV-Visible, 1H NMR and 31P NMR spectral studies. The crystal structure and morphology of the hybrid complexes was investigated with the help of X-ray powder diffraction (XRPD), Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The thermal properties of 1a-c and 2a-c were studied by thermogravimetric (TG) analysis. The electrochemical behaviour of the complexes reveals that all complexes displayed a quasireversible redox behaviour corresponding to Ru(II)/Ru(III) and Ni(II)/Ni(III) couples for 1a-c and only Ru(II)/Ru(III) couple for 2a-c. All complexes are emissive in solution at room temperature revealing the influence of substituents and solvent polarity on emission properties of the complexes.

Successful prolonged ex vivo lung perfusion for graft preservation in rats.

PubMed

Noda, Kentaro; Shigemura, Norihisa; Tanaka, Yugo; Bhama, Jay K; D'Cunha, Jonathan; Luketich, James D; Bermudez, Christian A

2014-03-01

Ex vivo lung perfusion (EVLP) strategies represent a new frontier in lung transplantation technology, and there have been many clinical studies of EVLP in lung transplantation. The establishment of a reliable EVLP model in small animals is crucial to facilitating translational research using an EVLP strategy. The main objective of this study was to develop a reproducible rat EVLP (R-EVLP) model that enables prolonged evaluation of the explanted lung during EVLP and successful transplantation after EVLP. The donor heart-lung blocks were procured with cold low-potassium dextran solution and immersed in the solution for 1 h at 4 °C. And then, the heart-lung blocks were flushed retrogradely and warmed up to 37 °C in a circuit perfused antegradely with acellular perfusate. The perfusate was deoxygenated with a gas mixture (6% O2, 8% CO2, 86% N2). The perfusion flow was maintained at 20% of the entire cardiac output. At 37 °C, the lungs were mechanically ventilated and perfusion continued for 4 h. Every hour, the perfused lung was evaluated for gas exchange, dynamic lung compliance (Cdyn) and pulmonary vascular resistance (PVR). R-EVLP was performed for 4 h. Pulmonary oxygenation ability (pO2/pCO2) was stable for 4 h during EVLP. It was noted that Cdyn and PVR were also stable. After 4 h of EVLP, pO2 was 303 ± 19 mmHg, pCO2 was 39.6 ± 1.2 mmHg, PVR was 1.75 ± 0.10 mmHg/ml/min and Cdyn was 0.37 ± 0.03 ml/cmH2O. Lungs that were transplanted after 2 h of R-EVLP resulted in significantly better post-transplant oxygenation and compliance when compared with those after standard cold static preservation. Our R-EVLP model maintained stable lung oxygenation, compliance and vascular resistance for up to 4 h of perfusion duration. This reliable model should facilitate further advancement of experimental work using EVLP.

Green polymer chemistry: investigating the mechanism of radical ring-opening redox polymerization (R3P) of 3,6-dioxa-1,8-octanedithiol (DODT).

PubMed

Rosenthal-Kim, Emily Q; Puskas, Judit E

2015-04-13

The mechanism of the new Radical Ring-opening Redox Polymerization (R3P) of 3,6-dioxa-1,8-octanedithiol (DODT) by triethylamine (TEA) and dilute H2O2 was investigated. Scouting studies showed that the formation of high molecular weight polymers required a 1:2 molar ratio of DODT to TEA and of DODT to H2O2. Further investigation into the chemical composition of the organic and aqueous phases by 1H-NMR spectroscopy and mass spectrometry demonstrated that DODT is ionized by two TEA molecules (one for each thiol group) and thus transferred into the aqueous phase. The organic phase was found to have cyclic disulfide dimers, trimers and tetramers. Dissolving DODT and TEA in water before the addition of H2O2 yielded a polymer with Mn = 55,000 g/mol, in comparison with Mn = 92,000 g/mol when aqueous H2O2 was added to a DODT/TEA mixture. After polymer removal, MALDI-ToF MS analysis of the residual reaction mixtures showed only cyclic oligomers remaining. Below the LCST for TEA in water, 18.7 °C, the system yielded a stable emulsion, and only cyclic oligomers were found. Below DODT/TEA and H2O2 1:2 molar ratio mostly linear oligomers were formed, with <20% cyclic oligomers. The findings support the proposed mechanism of R3P.

Vaporization thermodynamic studies by high-temperature mass spectrometry on some three-phase regions over the MnO-TeO2 binary line in the Mn-Te-O ternary system.

PubMed

Narasimhan, T S Lakshmi; Sai Baba, M; Viswanathan, R

2006-12-28

Knudsen effusion mass spectrometric measurements have been performed in the temperature range of 850-950 K over four three-phase mixtures, each phase mixture having at least one phase lying on the MnO-TeO2 binary line of the Mn-Te-O phase diagram, and the rest of the phases lying above this binary line. The three-phase mixtures investigated are Mn3O4 + MnO + Mn6Te5O16; Mn3O4 + Mn6Te5O16 + MnTeO3; Mn3O4 + Mn3TeO6 + MnTeO3; and Mn3TeO6 + MnTeO3 + Mn2Te3O8. The vapor pressures of the gaseous species TeO2, TeO, and Te2 over these three-phase mixtures were measured, and various heterogeneous solid-gas reactions were evaluated along with the homogeneous gas-phase reaction TeO2(g) + 0.5Te2(g) = 2 TeO(g). The enthalpy and Gibbs free energy of formation of the four ternary Mn-Te-O phases were deduced at T = 900 K. These values (in kJ.mol-1), along with the estimated uncertainties in them are Delta(f)H(o)m = 4150 +/- 19, 752 +/- 11, 1710 +/- 11, 1924 +/- 40, and Delta(f)G(o)m= 2835 +/- 28, 511 +/- 11, 1254 +/- 19, 1238 +/- 38, for Mn6Te5O16, MnTeO3, Mn3TeO6, and Mn2Te3O8, respectively. A thermochemical assessment was made to examine the conditions under which the ternary Mn-Te-O phases could be formed on a stainless steel clad of mixed-oxide-fueled (MO2; M = U + Pu) fast breeder nuclear reactors. The phase Mn3TeO6 could be formed when the fuel is even slightly hyperstoichiometric (O/M = 2.0002) and the phase Mn6Te5O16 could also be formed when O/M = 2.0004. The threshold tellurium potential for the formation of Mn3TeO6 is higher than that for MnTe0.80 and CrTe1.10, but is comparable to that for MoTe1.10, and even lower than that for FeTe0.81 or NiTe0.63.

Asymmetric synthesis of 5-arylcyclohexenones by rhodium(I)-catalyzed conjugate arylation of racemic 5-(trimethylsilyl)cyclohexenone with arylboronic acids.

PubMed

Chen, Qian; Kuriyama, Masami; Soeta, Takahiro; Hao, Xinyu; Yamada, Ken-ichi; Tomioka, Kiyoshi

2005-09-29

[reaction: see text] A catalytic asymmetric conjugate arylation of racemic 5-(trimethylsilyl)cyclohex-2-enone with arylboronic acids was catalyzed by 3 mol % chiral amidophosphane- or BINAP-Rh(I) in dioxane-water (10:1) to afford trans- and cis-3-aryl-5-(trimethylsilyl)cyclohexanones in high enantioselectivity. Dehydrosilylation of the product mixture with cupric chloride in DMF gave 5-arylcyclohex-2-enones with up to 93% ee in good yield. Enantiofacial selectivity with chiral phosphane-Rh(I) exceeds the trans-diastereoselectivity that is maintained in the achiral or racemic phosphane-Rh(I)-catalyzed conjugate arylation of 5-(trimethylsilyl)cyclohexenone.

21 CFR 184.1201 - Calcium glycerophosphate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Calcium glycerophosphate. 184.1201 Section 184... as GRAS § 184.1201 Calcium glycerophosphate. (a) Calcium glycerophosphate (C3H7CaO6P, CAS Reg. No... mixture of calcium β-, and D-, and L-α-glycerophosphate. (b) The ingredient meets the specifications of...

Pathways to Oxygen-Bearing Molecules in the Interstellar Medium and in Planetary Atmospheres: Cyclopropenone (c-C3H2O) and Propynal (HCCCHO)

NASA Astrophysics Data System (ADS)

Zhou, Li; Kaiser, Ralf I.; Gao, Li Gyun; Chang, Agnes H. H.; Liang, Mao-Chang; Yung, Yuk L.

2008-10-01

We investigated the formation of two C3H2O isomers, i.e., cyclopropenone (c-C3H2O) and propynal (HCCCHO), in binary ice mixtures of carbon monoxide (CO) and acetylene (C2H2) at 10 K in an ultrahigh vacuum machine on high-energy electron irradiation. The chemical evolution of the ice samples was followed online and in situ via a Fourier transform infrared spectrometer and a quadrupole mass spectrometer. The temporal profiles of the cyclopropenone and propynal isomers suggest (pseudo-) first-order kinetics. The cyclic structure (c-C3H2O) is formed via an addition of triplet carbon monoxide to ground-state acetylene (or vice versa); propynal (HCCCHO) can be synthesized from a carbon monoxide-acetylene complex via a [HCO...CCH] radical pair inside the matrix cage. These laboratory studies showed for the first time that both C3H2O isomers can be formed in low-temperature ices via nonequilibrium chemistry initiated by energetic electrons as formed in the track of Galactic cosmic ray particles penetrating interstellar icy grains in cold molecular clouds. Our results can explain the hitherto unresolved gas phase abundances of cyclopropenone in star-forming regions via sublimation of c-C3H2O as formed on icy grains in the cold molecular cloud stage. Implications for the heterogeneous oxygen chemistry of Titan and icy terrestrial planets and satellites suggest that the production of oxygen-bearing molecules such as C3H2O may dominate on aerosol particles compared to pure gas phase chemistry.

Ethyl 2-[(carbamoyl-amino)-imino]-propano-ate hemihydrate.

PubMed

Corrêa, Charlane C; Graúdo, José Eugênio J C; de Oliveira, Luiz Fernando C; de Almeida, Mauro V; Diniz, Renata

2011-08-01

The title compound, C(6)H(11)N(3)O(3)·0.5H(2)O, has two independent mol-ecules and one mol-ecule of water in the asymmetric unit. The crystal packing is stabilized by inter-molecular N-H⋯N, O-H⋯O, N-H⋯O and C-H⋯O hydrogen bonds. These inter-actions form a two-dimensional array in the ab plane with a zigzag motif which has an angle close to 35° between the zigzag planes. The hydrogen bonding can be best described using the graph-set notation as N(1) = C(10)R(2) (2)(10)R(2) (2)(8) and N(2) = R(6) (4)(20)R(2) (2)(8).

Stability of methane in reduced C-O-H fluid at 6.3 GPa and 1300-1400°C

NASA Astrophysics Data System (ADS)

Sokol, A. G.; Tomilenko, A. A.; Bul'bak, T. A.; Palyanova, G. A.; Palyanov, Yu. N.; Sobolev, N. V.

2017-06-01

The composition of a reduced C-O-H fluid was studied by the method of chromatography-mass spectrometry under the conditions of 6.3 GPa, 1300-1400°C, and fO2 typical of the base of the subcratonic lithosphere. Fluids containing water (4.4-96.3 rel. %), methane (37.6-0.06 rel. %), and variable concentrations of ethane, propane, and butane were obtained in experiments. With increasing fO2, the proportion of the CH4/C2H6 peak areas on chromatograms first increases and then decreases, whereas the CH4/C3H8 and CH4/C4H10 ratios continually decrease. The new data show that ethane and heavier HCs may be more stable to oxidation, than previously thought. Therefore, when reduced fluids pass the "redox-front," carbon is not completely released from the fluid and may be involved in diamond formation.

Crystal structures of fac-tri-carbonyl-chlorido-(6,6'-dihy-droxy-2,2'-bi-pyridine)-rhenium(I) tetra-hydro-furan monosolvate and fac-bromido-tricarbon-yl(6,6'-dihy-droxy-2,2'-bi-pyridine)-manganese(I) tetra-hydro-furan monosolvate.

PubMed

Lense, Sheri; Piro, Nicholas A; Kassel, Scott W; Wildish, Andrew; Jeffery, Brent

2016-08-01

The structures of two facially coordinated Group VII metal complexes, fac-[ReCl(C10H8N2O2)(CO)3]·C4H8O (I·THF) and fac-[MnBr(C10H8N2O2)(CO)3]·C4H8O (II·THF), are reported. In both complexes, the metal ion is coordinated by three carbonyl ligands, a halide ligand, and a 6,6'-dihy-droxy-2,2'-bi-pyridine ligand in a distorted octa-hedral geometry. Both complexes co-crystallize with a non-coordinating tetra-hydro-furan (THF) solvent mol-ecule and exhibit inter-molecular but not intra-molecular hydrogen bonding. In both crystal structures, chains of complexes are formed due to inter-molecular hydrogen bonding between a hy-droxy group from the 6,6'-dihy-droxy-2,2'-bi-pyridine ligand and the halide ligand from a neighboring complex. The THF mol-ecule is hydrogen bonded to the remaining hy-droxy group.

Conformational Aspects of the O-acetylation of C-tetra(phenyl)calixpyrogallol[4]arene.

PubMed

Casas-Hinestroza, José Luis; Maldonado, Mauricio

2018-05-20

Reaction between pyrogallol and benzaldehyde results in a conformational mixture of C- tetra(phenyl)pyrogallol[4]arene (crown and chair). The conformer mixture was separated using crystallization procedures and the structures were determined using FTIR, ¹H-NMR, and 13 C-NMR. O -acetylation of C- tetra(phenyl)pyrogallol[4]arene (chair) with acetic anhydride, in pyridine results in the formation of dodecaacetyl-tetra(phenyl)pyrogallol[4]arene. The structure was determined using ¹H-NMR and 13 C-NMR finding that the product maintains the conformation of the starting conformer. On the other hand, the O -acetylation reaction of C- tetra(phenyl)pirogallol[4]arene (crown) under same conditions proceeded efficiently, and its structure was determined using ¹H-NMR and 13 C-NMR. Dynamic ¹H-NMR of acetylated pyrogallolarene was studied by means of variable temperature in DMSO- d ₆ solution, and it revealed that two conformers are formed in the solution. Boat conformations for acetylated pyrogallolarene showed a slow interconversion at room temperature.

Composition and origin of coalbed gases in the Lower Silesian basin, southwest Poland

USGS Publications Warehouse

Kotarba, M.J.; Rice, D.D.

2001-01-01

Coalbed gases in the Lower Silesian Coal Basin (LSCB) of Poland are highly variable in both their molecular and stable isotope compositions. Geochemical indices and stable isotope ratios vary within the following ranges: hydrocarbon (CHC) index CHC = CH4/(C2H6+C3H8) from 1.1 to 5825, wet gas (C2+) index C2+ = (C2H6+ C3H8+ C4H10+ C5H12) / (CH4+ C2H6+ C3H8+ C4H10+ C5H12) 100 (%) from 0.0 to 48.3%, CO2-CH4 (CDMI) index CDMI = CO2/ (CO2+ CH4) 100 (%) from 0.1 to 99.9%, ??13C(CH4) from -66.1 to -24.6%o, ??D(CH4) from -266 to -117%o, ??13C(C2H6) from -27.8 to -22.8%o, and ??13C(CO2) from -26.6 to 16.8%o. Isotopic studies reveal the presence of 3 genetic types of natural gases: thermogenic (CH4, higher gaseous hydrocarbons, and CO2), endogenic CO2, and microbial CH4 and CO2. Thermogenic gases resulted from coalification processes, which were probably completed by Late Carboniferous and Early Permian time. Endogenic CO2 migrated along the deep-seated faults from upper mantle and/or magma chambers. Minor volumes of microbial CH4 and CO2 occur at shallow depths close to the abandoned mine workings. "Late-stage" microbial processes have commenced in the Upper Cretaceous and are probably active at present. However, depth-related isotopic fractionation which has resulted from physical and physicochemical (e.g. diffusion and adsorption/desorption) processes during gas migration cannot be neglected. The strongest rock and gas outbursts occur only in those parts of coal deposits of the LSCB which are dominated by large amounts of endogenic CO2. ?? 2001 Elsevier Science Ltd.

C6, C7, and C8 perfluoroalkyl-substituted phosphinic acids.

PubMed

Singh, R P; Shreeve, J M

2000-04-17

Reaction of red phosphorus with RfI in a 1:2 molar ratio at 230 degrees C led to the formation of a mixture of (Rf)2PI and (Rf)PI2 (Rf = C6F13, C7F15, C8F17) in about a 70:30 ratio, respectively. These mixtures were separated by vacuum distillation. (Rf)2PI (Rf = C6F13, C7F15) are yellow liquids whereas (C8F17)2PI is a yellow solid. Oxidation of (Rf)2PI with excess NO2 led to (Rf)2P(O)OH (Rf = C6F13, C7F15, C8F17) in > 90% isolated yields after aqueous hydrolysis of the anhydride intermediates. These highly fluorinated phosphinic acids are white solids with sharp melting points and are highly soluble in methyl sulfoxide (DMSO) and 1,1,2-trichlorotrifluoroethane. However, solubility in chloroform and methylene dichloride is low. These perfluoroalkylphosphinic acids were characterized by IR, NMR (1H, 19F, and 31P), and mass spectra and elemental analysis.

Performance and Mechanism of Piezo-Catalytic Degradation of 4-Chlorophenol: Finding of Effective Piezo-Dechlorination.

PubMed

Lan, Shenyu; Feng, Jinxi; Xiong, Ya; Tian, Shuanghong; Liu, Shengwei; Kong, Lingjun

2017-06-06

Piezo-catalysis was first used to degrade a nondye pollutant, 4-chlorophenol (4-CP). In this process, hydrothermally synthesized tetragonal BaTiO 3 nano/micrometer-sized particles were used as the piezo-catalyst, and the ultrasonic irradiation with low frequency was selected as the vibration energy to cause the deformation of tetragonal BaTiO 3 . It was found that the piezoelectric potential from the deformation could not only successfully degrade 4-chlorophenol but also effectively dechlorinate it at the same time, and five kinds of dechlorinated intermediates, hydroquinone, benzoquinone, phenol, cyclohexanone, and cyclohexanol, were determined. This is the first sample of piezo-dechlorination. Although various active species, including h + , e - , •H, •OH, •O 2 - , 1 O 2 , and H 2 O 2 , were generated in the piezoelectric process, it was confirmed by ESR, scavenger studies, and LC-MS that the degradation and dechlorination were mainly attributed to •OH radicals. These •OH radicals were chiefly derived from the electron reduction of O 2 , partly from the hole oxidation of H 2 O. These results indicated that the piezo-catalysis was an emerging and effective advanced oxidation technology for degradation and dechlorination of organic pollutants.

Mercury(II) complexes of unsymmetric phosphorus ylides: Synthesis, spectroscopic and antibacterial activity studies

NASA Astrophysics Data System (ADS)

Sabounchei, Seyyed Javad; Panahimehr, Mohammad; Hosseinzadeh, Marjan; Karamian, Roya; Asadbegy, Mostafa; Masumi, Azadeh

2014-03-01

The reaction of Ph2PCH2PPh2 (dppm) with 2-bromo-3-nitroacetophenone and 2,2‧,4‧-trichloroacetophenone in chloroform produce the new phosphonium salts [Ph2PCH2PPh2CH2C(O)C6H4NO2]Br (1) and [Ph2PCH2PPh2CH2C(O)C6H3Cl2]Cl (2). Further, by reaction of the monophosphonium salts of dppm with the strong base triethylaminethe corresponding bidentate phosphorus ylides, Ph2PCH2PPh2C(H)C(O)C6H4NO2 (3) and Ph2PCH2PPh2C(H)C(O)C6H3Cl2 (4) were obtained. The reaction of these ligands with mercury(II) halides in dry methanol led to the formation of the mononuclear complexes {HgX2[(Ph2PCH2PPh2C(H)C(O)C6H4NO2)]} [X = Cl (5), Br (6), I (7)] and {HgX2[(Ph2PCH2PPh2C(H)C(O)C6H3Cl2)]} [X = Cl (8), Br (9), I (10)]. Characterization of the obtained compounds was performed by elemental analysis, IR, 1H, 31P and 13C NMR. The structure of compound 1 being unequivocally determined by single crystal X-ray diffraction techniques. The mass spectrum of compound 6 (as an instance) also demonstrates the synthesize of these compounds. In all complexes the title ylides are coordinated through the ylidic carbon and the phosphine atom. These compounds form five membered ring under complexation. The antibacterial effects of DMSO solutions of the ligands and their metal complexes were evaluated by the disc diffusion method against six Gram positive and negative bacteria. All compounds represent antibacterial activity against these bacteria with high levels of inhibitory potency exhibited against the Gram positive species.

The unexpectedly bright comet C/2012 F6 (Lemmon) unveiled at near-infrared wavelengths

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paganini, Lucas; DiSanti, Michael A.; Mumma, Michael J.

2014-01-01

We acquired near-infrared spectra of the Oort cloud comet C/2012 F6 (Lemmon) at three different heliocentric distances (R {sub h}) during the comet's 2013 perihelion passage, providing a comprehensive measure of the outgassing behavior of parent volatiles and cosmogonic indicators. Our observations were performed pre-perihelion at R {sub h} = 1.2 AU with CRIRES (on 2013 February 2 and 4), and post-perihelion at R {sub h} = 0.75 AU with CSHELL (on March 31 and April 1) and R {sub h} = 1.74 AU with NIRSPEC (on June 20). We detected 10 volatile species (H{sub 2}O, OH* prompt emission, C{submore » 2}H{sub 6}, CH{sub 3}OH, H{sub 2}CO, HCN, CO, CH{sub 4}, NH{sub 3}, and NH{sub 2}), and obtained upper limits for two others (C{sub 2}H{sub 2} and HDO). One-dimensional spatial profiles displayed different distributions for some volatiles, confirming either the existence of polar and apolar ices, or of chemically distinct active vents in the nucleus. The ortho-para ratio for water was 3.31 ± 0.33 (weighted mean of CRIRES and NIRSPEC results), implying a spin temperature >37 K at the 95% confidence limit. Our (3σ) upper limit for HDO corresponds to D/H < 2.45 × 10{sup –3} (i.e., <16 Vienna Standard Mean Ocean Water, VSMOW). At R {sub h} = 1.2 AU (CRIRES), the production rate for water was Q(H{sub 2}O) = 1.9 ± 0.1 × 10{sup 29} s{sup –1} and its rotational temperature was T {sub rot} ∼ 69 K. At R {sub h} = 0.75 AU (CSHELL), we measured Q(H{sub 2}O) = 4.6 ± 0.6 × 10{sup 29} s{sup –1} and T {sub rot} = 80 K on March 31, and 6.6 ± 0.9 × 10{sup 29} s{sup –1} and T {sub rot} = 100 K on April 1. At R {sub h} = 1.74 AU (NIRSPEC), we obtained Q(H{sub 2}O) = 1.1 ± 0.1 × 10{sup 29} s{sup –1} and T {sub rot} ∼ 50 K. The measured volatile abundance ratios classify comet C/2012 F6 as rather depleted in C{sub 2}H{sub 6} and CH{sub 3}OH, while HCN, CH{sub 4}, and CO displayed abundances close to their median values found among comets. H{sub 2}CO was the only volatile showing a relative enhancement. The relative paucity of C{sub 2}H{sub 6} and CH{sub 3}OH (with respect to H{sub 2}O) suggests formation within warm regions of the nebula. However, the normal abundance of HCN and hypervolatiles CH{sub 4} and CO, and the enhancement of H{sub 2}CO, may indicate a possible heterogeneous nucleus of comet C/2012 F6 (Lemmon), possibly as a result of radial mixing within the protoplanetary disk.« less

Crystal chemistry of elpidite from Khan Bogdo (Mongolia) and its K- and Rb-exchanged forms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grigor'eva, A. A.; Zubkova, N. V., E-mail: nata_zubkova@rambler.ru; Pekov, I. V.

2011-09-15

Elpidite Na{sub 2}ZrSi{sub 6}O{sub 15} {center_dot} 3H{sub 2}O [space group Pbcm, a = 7.1312(12), b = 14.6853(12), and c = 14.6349(15) Angstrom-Sign ] from Khan Bogdo (Mongolia) and its K- and Rb-exchanged forms K{sub 1.78}Na{sub 0.16}H{sub 0.06}ZrSi{sub 6}O{sub 15} {center_dot} 0.85H{sub 2}O [Cmce, a = 14.054(3), b = 14.308(3), and c = 14.553(3) Angstrom-Sign ] and Na{sub 1.58}Rb{sub 0.2}H{sub 0.22}ZrSi{sub 6}O{sub 15} {center_dot} 2.69H{sub 2}O [Pbcm, a = 7.1280(10), b = 14.644(3), and c = 14.642(3) Angstrom-Sign ] that were obtained by cation exchange at 90 Degree-Sign C, as well as K{sub 1.84}Na{sub 0.11}H{sub 0.05}ZrSi{sub 6}O{sub 15} {center_dot} 0.91H{sub 2}Omore » [Cmce, a = 14.037(3), b = 14.226(3), and c = 14.552(3) Angstrom-Sign ] and Rb{sub 1.78}Na{sub 0.06}H{sub 0.16}ZrSi{sub 6}O{sub 15} {center_dot} 0.90H{sub 2}O [Cmce, a = 14.2999(12), b = 14.4408(15), and c = 14.7690(12) Angstrom-Sign ], obtained at 150 Degree-Sign C are studied by single-crystal X-ray diffraction and IR spectroscopy. The base of the structures is a heteropolyhedral Zr-Si-O framework whose cavities accommodate Na (K, Rb) cations and H{sub 2}O molecules.« less

Vapor-liquid phase equilibria of potassium chloride-water mixtures: Equation-of-state representation for KCl-H2O and NaCl-H2O

USGS Publications Warehouse

Hovey, J.K.; Pitzer, Kenneth S.; Tanger, J.C.; Bischoff, J.L.; Rosenbauer, R.J.

1990-01-01

Measurements of isothermal vapor-liquid compositions for KCl-H2O as a function of pressure are reported. An equation of state, which was originally proposed by Pitzer and was improved and used by Tanger and Pitzer to fit the vapor-liquid coexistence surface for NaCl-H2O, has been used for representation of the KCl-H2O system from 300 to 410??C. Improved parameters are also reported for NaCl-H2O from 300 to 500??C. ?? 1990 American Chemical Society.

Adsorptive separation studies of ethane-methane and methane-nitrogen systems using mesoporous carbon.

PubMed

Yuan, Bin; Wu, Xiaofei; Chen, Yingxi; Huang, Jianhan; Luo, Hongmei; Deng, Shuguang

2013-03-15

Adsorptive separations of C(2)H(6)/CH(4) and CH(4)/N(2) binary mixtures are of paramount importance from the energy and environmental points of view. A mesoporous carbon adsorbent was synthesized using a soft template method and characterized with TEM, TGA, and nitrogen adsorption/desorption. Adsorption equilibrium and kinetics of C(2)H(6), CH(4), and N(2) on the mesoporous carbon adsorbent were determined at 278, 298, and 318 K and pressures up to 100 kPa. The adsorption capacities of C(2)H(6) and CH(4) on the mesoporous carbon adsorbent at 298 K and 100 kPa are 2.20 mmol/g and 1.05 mmol/g, respectively. Both are significantly higher than those of many adsorbents including pillared clays and ETS-10 at a similar condition. The equilibrium selectivities of C(2)H(6)/CH(4) and CH(4)/N(2) at 298 K are 19.6 and 5.8, respectively. It was observed that the adsorption of C(2)H(6), CH(4), and N(2) gases on the carbon adsorbent was reversible with modest isosteric heats of adsorption, which implies that this carbon adsorbent can be easily regenerated in a cyclic adsorption process. These results suggest that the mesoporous carbon studied in this work is a promising alternative adsorbent for the separations of C(2)H(6)/CH(4) and CH(4)/N(2) gas mixtures. Copyright © 2012 Elsevier Inc. All rights reserved.

Lethality of chlorine, chlorine dioxide, and a commercial fruit and vegetable sanitizer to vegetative cells and spores of Bacillus cereus and spores of Bacillus thuringiensis.

PubMed

Beuchat, Larry R; Pettigrew, Charles A; Tremblay, Mario E; Roselle, Brian J; Scouten, Alan J

2004-08-01

Chlorine, ClO2, and a commercial raw fruit and vegetable sanitizer were evaluated for their effectiveness in killing vegetative cells and spores of Bacillus cereus and spores of Bacillus thuringiensis. The ultimate goal was to use one or both species as a potential surrogate(s) for Bacillus anthracis in studies that focus on determining the efficacy of sanitizers in killing the pathogen on food contact surfaces and foods. Treatment with alkaline (pH 10.5 to 11.0) ClO2 (200 microg/ml) produced by electrochemical technologies reduced populations of a five-strain mixture of vegetative cells and a five-strain mixture of spores of B. cereus by more than 5.4 and more than 6.4 log CFU/ml respectively, within 5 min. This finding compares with respective reductions of 4.5 and 1.8 log CFU/ml resulting from treatment with 200 microg/ml of chlorine. Treatment with a 1.5% acidified (pH 3.0) solution of Fit powder product was less effective, causing 2.5- and 0.4-log CFU/ml reductions in the number of B. cereus cells and spores, respectively. Treatment with alkaline ClO2 (85 microg/ml), acidified (pH 3.4) ClO2 (85 microg/ml), and a mixture of ClO2 (85 microg/ml) and Fit powder product (0.5%) (pH 3.5) caused reductions in vegetative cell/spore populations of more than 5.3/5.6, 5.3/5.7, and 5.3/6.0 log CFU/ml, respectively. Treatment of B. cereus and B. thuringiensis spores in a medium (3.4 mg/ml of organic and inorganic solids) in which cells had grown and produced spores with an equal volume of alkaline (pH 12.1) ClO2 (400 microg/ml) for 30 min reduced populations by 4.6 and 5.2 log CFU/ml, respectively, indicating high lethality in the presence of materials other than spores that would potentially react with and neutralize the sporicidal activity of ClO2.

Simultaneous determination of dissolved gases and moisture in mineral insulating oils by static headspace gas chromatography with helium photoionization pulsed discharge detection.

PubMed

Jalbert, J; Gilbert, R; Tétreault, P

2001-07-15

This paper presents the development of a static headspace capillary gas chromatographic method (HS-GC) for simultaneously determining dissolved gases (H2, O2, N2, CO, CO2, CH4, C2H6, C2H4, C2H2, C3H8) and moisture from a unique 15-mL mineral oil sample. A headspace sampler device is used to equilibrate the sample species in a two-phase system under controlled temperature and agitation conditions. A portion of the equilibrated species is then automatically split-injected into two chromatographic channels mounted on the same GC for their separation. The hydrocarbons and the lighter gases are separated on the first channel by a GS-Q column coupled with a MolSieve 5-A column via a bypass valve, while the moisture is separated on the second channel using a Stabilwax column. The analytes are detected by using two universal pulsed-discharge helium ionization detectors (PDHID). The performance of the method was established using equilibrated vials containing known amounts of gas mixture, water, and blank oil. The signal is linear over the concentration ranges normally found for samples collected from open-breathing power transformers. Determination sensitivity varies with the nature of the species considered with values as high as 21 500 A x 10(-9) s (microg/ g)(-1) for H2O, 46-216 A x 10(-9) s (microL/L)(-1) for the hydrocarbons and carbon oxides, and as low as 8-21 A x 10(-9) s (microL/L)(-1) for the O2 and N2 permanent gases. The detection limit of the method is between 0.08 and 6 microL/L for the dissolved gases, except for O2, N2, and CO2, where higher values are observed due to air intrusion during sampler operations, and 0.1 microg/g for the dissolved water. Ten consecutive measurements in the low and high levels of the calibration curves have shown a precision better than 12% and 6%, respectively, in all cases. A comparison study between the HS-GC method and the ASTM standard procedures on 31 field samples showed a very good agreement of the results. The advantages of configuring the arrangement with two PDHID over the conventional flame ionization and thermal conductivity detectors were clearly demonstrated.

Highly productive CNN pincer ruthenium catalysts for the asymmetric reduction of alkyl aryl ketones.

PubMed

Baratta, Walter; Chelucci, Giorgio; Magnolia, Santo; Siega, Katia; Rigo, Pierluigi

2009-01-01

Chiral pincer ruthenium complexes of formula [RuCl(CNN)(Josiphos)] (2-7; Josiphos = 1-[1-(dicyclohexylphosphano)ethyl]-2-(diarylphosphano)ferrocene) have been prepared by treating [RuCl(2)(PPh(3))(3)] with (S,R)-Josiphos diphosphanes and 1-substituted-1-(6-arylpyridin-2-yl)methanamines (HCNN; substituent = H (1 a), Me (1 b), and tBu (1 c)) with NEt(3). By using 1 b and 1 c as a racemic mixture, complexes 4-7 were obtained through a diastereoselective synthesis promoted by acetic acid. These pincer complexes, which display correctly matched chiral PP and CNN ligands, are remarkably active catalysts for the asymmetric reduction of alkyl aryl ketones in basic alcohol media by both transfer hydrogenation (TH) and hydrogenation (HY), achieving enantioselectivities of up to 99 %. In 2-propanol, the enantioselective TH of ketones was accomplished by using a catalyst loading as low as 0.002 mol % and afforded a turnover frequency (TOF) of 10(5)-10(6) h(-1) (60 and 82 degrees C). In methanol/ethanol mixtures, the CNN pincer complexes catalyzed the asymmetric HY of ketones with H(2) (5 atm) at 0.01 mol % relative to the complex with a TOF of approximately 10(4) h(-1) at 40 degrees C.

Thermal, vibrational and optical properties of PrLuO3 interlanthanides from hydrothermally-derived precursors.

PubMed

Soares, Júlia C; Siqueira, Kisla P F; de Sousa Filho, Paulo C; Moreira, Roberto L; Dias, Anderson

2017-01-17

PrLuO 3 interlanthanides were prepared at temperatures ranging from 800 °C to 1600 °C using hydrothermally-derived precursors. The chemical reactions observed include the conversion and segregation of Pr(OH) 3 and LuO(OH), respectively, into PrO 2 and Lu 2 O 3 cubic oxides below 1200 °C, followed by the production of a mixture of hexagonal P6 3 /mmc and orthorhombic Pnma PrLuO 3 phases at 1400 °C. Phase-pure orthorhombic PrLuO 3 was obtained at 1600 °C, which was corroborated by Raman and micro far-infrared spectroscopic analyses. Photoluminescence, colorimetric and lifetime measurements were carried out in PrLuO 3 samples. Dominant emission verified in samples calcined at 1400 °C corresponds to the hypersensitive 3 P 0 → 3 F 2 transition with a color purity of 97% (decay times of 12 μs and 3 μs), while emissions for the phase-pure samples correspond to the 3 P 0 → 3 H 6 and 3 P 0 → 3 H 5 transitions with a color purity of 94% (a single luminescence lifetime of 12 μs). The optical properties of PrLuO 3 interlanthanides thereby suggest that they can be used as luminescent materials in both structural arrangements.

Unusual centrosymmetric structure of [M(18-crown-6)](+) (M = Rb, Cs and NH4) complexes stabilized in an environment of hexachloridoantimonate(V) anions.

PubMed

Ponomarova, Vira V; Rusanova, Julia A; Rusanov, Eduard B; Domasevitch, Konstantin V

2015-10-01

In (1,4,7,10,13,16-hexaoxacyclooctadecane)rubidium hexachloridoantimonate(V), [Rb(C12H24O6)][SbCl6], (1), and its isomorphous caesium {(1,4,7,10,13,16-hexaoxacyclooctadecane)caesium hexachloridoantimonate(V), [Cs(C12H24O6)][SbCl6]}, (2), and ammonium {ammonium hexachloridoantimonate(V)-1,4,7,10,13,16-hexaoxacyclooctadecane (1/1), (NH4)[SbCl6]·C12H24O6}, (3), analogues, the hexachloridoantimonate(V) anions and 18-crown-6 molecules reside across -3 axes passing through the Sb atoms and the centroids of the 18-crown-6 groups, both of which coincide with centres of inversion. The Rb(+) [in (1)], Cs(+) [in (2)] and NH4(+) [in (3)] cations are situated inside the cavity of the 18-crown-6 ring; they are situated on -3 axes and are equally disordered about centres of inversion, deviating from the centroid of the 18-crown-6 molecule by 0.4808 (13), 0.9344 (7) and 0.515 (8) Å, respectively. Interaction of the ammonium cation and the 18-crown-6 group is supported by three equivalent hydrogen bonds [N...O = 2.928 (3) Å and N-H...O = 162°]. The centrosymmetric structure of [Cs(18-crown-6)](+), with the large Cs(+) cation approaching the centre of the ligand cavity, is unprecedented and accompanied by unusually short Cs-O bonds [2.939 (2) and 3.091 (2) Å]. For all three compounds, the [M(18-crown-6)](+) cations and [SbCl6](-) anions afford linear stacks along the c axis, with the cationic complexes embedded between pairs of inversion-related anions.

Chemical reactivity of SiC fibre-reinforced SiC with beryllium and lithium ceramic breeder materials

NASA Astrophysics Data System (ADS)

Kleykamp, H.

2000-12-01

SiC fibre-reinforced SiC fabrics (f-SiC/SiC) are considered for structural materials of advanced fusion blanket concepts. Priority tasks are compatibility studies of SiC with Li breeder ceramics and the Be neutron multiplier. Isothermal and anisothermal powder reactions by DTA up to 1220°C were examined between Li 4SiO 4, Li 2ZrO 3 and Li 2TiO 3, respectively, and SiC and SiC/SiO 2 mixtures, respectively. The SiC/SiO 2 mixture simulated the chemical state of Nicalon fibres. Solid state reactions between SiC and Be pellets were studied by capsule experiments. The reaction products Be 2C and Si were observed between the initial phases after annealing at 800°C and 900°C. A parabolic time law with a chemical diffusion coefficient D˜=2.6×10 -15 m 2/s of Be in the products was deduced at 900°C. Additional oxygen released from SiO 2 as a component of the simulated fibres oxidised the reaction products via the gas phase by formation of a Be 2SiO 4 layer. All reactions are kinetically hindered below 700°C.

A simple hydrogen-bonded chain in (3Z)-3-{1-[(5-phenyl-1H-pyrazol-3-yl)amino]ethylidene}-4,5-dihydrofuran-2(3H)-one, and a hydrogen-bonded ribbon of centrosymmetric rings in the self-assembled adduct (3Z)-3-{1-[(5-methyl-1H-pyrazol-3-yl)amino]ethylidene}-4,5-dihydrofuran-2(3H)-one-6-(2-hydroxyethyl)-2,5-dimethylpyrazolo[1,5-a]pyrimidin-7(4H)-one (1/1).

PubMed

Quiroga, Jairo; Portilla, Jaime; Cobo, Justo; Glidewell, Christopher

2010-01-01

(3Z)-3-{1-[(5-Phenyl-1H-pyrazol-3-yl)amino]ethylidene}-4,5-dihydrofuran-2(3H)-one, C(15)H(15)N(3)O(2), (I), and the stoichiometric adduct (3Z)-3-{1-[(5-methyl-1H-pyrazol-3-yl)amino]ethylidene}-4,5-dihydrofuran-2(3H)-one-6-(2-hydroxyethyl)-2,5-dimethylpyrazolo[1,5-a]pyrimidin-7(4H)-one (1/1), C(10)H(13)N(3)O(2).C(10)H(13)N(3)O(2), (II), in which the two components have the same composition but different constitutions, are formed in the reactions of 2-acetyl-4-butyrolactone with 5-amino-3-phenyl-1H-pyrazole and 5-amino-3-methyl-1H-pyrazole, respectively. In each compound, the furanone component contains an intramolecular N-H...O hydrogen bond. The molecules of (I) are linked into a chain by a single intermolecular N-H...O hydrogen bond, while in (II), a combination of one O-H...N hydrogen bond, within the selected asymmetric unit, and two N-H...O hydrogen bonds link the molecular components into a ribbon containing alternating centrosymmetric R(4)(4)(20) and R(6)(6)(22) rings.

A Black Hills-Madison Aquifer origin for Dakota Aquifer groundwater in northeastern Nebraska.

PubMed

Stotler, Randy; Harvey, F Edwin; Gosselin, David C

2010-01-01

Previous studies of the Dakota Aquifer in South Dakota attributed elevated groundwater sulfate concentrations to Madison Aquifer recharge in the Black Hills with subsequent chemical evolution prior to upward migration into the Dakota Aquifer. This study examines the plausibility of a Madison Aquifer origin for groundwater in northeastern Nebraska. Dakota Aquifer water samples were collected for major ion chemistry and isotopic analysis ((18)O, (2)H, (3)H, (14)C, (13)C, (34)S, (18)O-SO(4), (87)Sr, (37)Cl). Results show that groundwater beneath the eastern, unconfined portion of the study area is distinctly different from groundwater sampled beneath the western, confined portion. In the east, groundwater is calcium-bicarbonate type, with delta(18)O values (-9.6 per thousand to -12.4 per thousand) similar to local, modern precipitation (-7.4 per thousand to -10 per thousand), and tritium values reflecting modern recharge. In the west, groundwater is calcium-sulfate type, having depleted delta(18)O values (-16 per thousand to -18 per thousand) relative to local, modern precipitation, and (14)C ages 32,000 to more than 47,000 years before present. Sulfate, delta(18)O, delta(2)H, delta(34)S, and delta(18)O-SO(4) concentrations are similar to those found in Madison Aquifer groundwater in South Dakota. Thus, it is proposed that Madison Aquifer source water is also present within the Dakota Aquifer beneath northeastern Nebraska. A simple Darcy equation estimate of groundwater velocities and travel times using reported physical parameters from the Madison and Dakota Aquifers suggests such a migration is plausible. However, discrepancies between (14)C and Darcy age estimates indicate that (14)C ages may not accurately reflect aquifer residence time, due to mixtures of varying aged water.

Formulation of 3D Printed Tablet for Rapid Drug Release by Fused Deposition Modeling: Screening Polymers for Drug Release, Drug-Polymer Miscibility and Printability.

PubMed

Solanki, Nayan G; Tahsin, Md; Shah, Ankita V; Serajuddin, Abu T M

2018-01-01

The primary aim of this study was to identify pharmaceutically acceptable amorphous polymers for producing 3D printed tablets of a model drug, haloperidol, for rapid release by fused deposition modeling. Filaments for 3D printing were prepared by hot melt extrusion at 150°C with 10% and 20% w/w of haloperidol using Kollidon ® VA64, Kollicoat ® IR, Affinsiol ™ 15 cP, and HPMCAS either individually or as binary blends (Kollidon ® VA64 + Affinisol ™ 15 cP, 1:1; Kollidon ® VA64 + HPMCAS, 1:1). Dissolution of crushed extrudates was studied at pH 2 and 6.8, and formulations demonstrating rapid dissolution rates were then analyzed for drug-polymer, polymer-polymer and drug-polymer-polymer miscibility by film casting. Polymer-polymer (1:1) and drug-polymer-polymer (1:5:5 and 2:5:5) mixtures were found to be miscible. Tablets with 100% and 60% infill were printed using MakerBot printer at 210°C, and dissolution tests of tablets were conducted at pH 2 and 6.8. Extruded filaments of Kollidon ® VA64-Affinisol ™ 15 cP mixtures were flexible and had optimum mechanical strength for 3D printing. Tablets containing 10% drug with 60% and 100% infill showed complete drug release at pH 2 in 45 and 120 min, respectively. Relatively high dissolution rates were also observed at pH 6.8. The 1:1-mixture of Kollidon ® VA64 and Affinisol ™ 15 cP was thus identified as a suitable polymer system for 3D printing and rapid drug release. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Inactivation by lemon juice of Escherichia coli O157:H7, Salmonella Enteritidis, and Listeria monocytogenes in beef marinating for the ethnic food kelaguen.

PubMed

Yang, Jian; Lee, Delores; Afaisen, Shayna; Gadi, Rama

2013-01-01

Lemon juice, a major source of acidulant citric acid, is frequently used in the preparation of ethnic foods. Raw or partially cooked meats are marinated with lemon juice in the preparation of a popular Chamorro dish called kelaguen, which is, unfortunately, strongly associated with foodborne illness outbreaks in Guam. We investigated the efficacy of lemon juice in reducing numbers of Escherichia coli O157:H7, Salmonella Enteritidis, and Listeria monocytogenes at stationary phase during marination. Beef inoculated with a three-strain mixture of E. coli O157:H7, S. Enteritidis, or L. monocytogenes at 10(6)CFU/mL was marinated with lemon juice from 0.2 to 10mL/g for 48h at 28°C. The decline of the pathogens during marination exhibited various degrees of deviation from first-order kinetics. Based on calculations with both linear regression and Weibull models, the decimal reduction time (4-D values) over the range of lemon concentrations was 366-5.1h for E. coli O157:H7, 282-2.4h for S. Enteritidis, and 104-2.4h for L. monocytogenes, indicating that E. coli O157:H7 was the most lemon-juice-resistant of the three. The pathogen reduction time (log 4-D values) plotted against undissociated titratable citric acid exhibited a biphasic pattern. The pathogen reduction time (log 4-D or δ values) was linearly correlated with the pH of the marinating beef (R(2)=0.92 to 0.98). The Z(pH) values (pH dependence of death rate) with beef marination were 1.03 for E. coli O157:H7, 0.92 for S. Enteritidis, and 1.29 for L. monocytogenes, indicating that L. monocytogenes was the most pH resistant of the three. L. monocytogenes exhibited less resistance to lemon juice than S. Enteritidis at pH of 3.5-4.4 but more resistance at pH of 2.6-2.8. In addition, at 4°C, all three pathogens exhibited 4-D values 1.7-4.1 times greater than those at 24°C at 5mL lemon juice/g beef. In conclusion, the usual beef marinating practice for kelaguen preparation (<0.5mL lemon juice/g beef for 1-12h) did not sufficiently inactivate E. coli O157:H7, S. Enteritidis, and L. monocytogenes to meet minimum food-safety requirements. To reduce the risk of kelaguen-associated foodborne illness, kelaguen preparation must include heat treatment in addition to marination with lemon juice. Published by Elsevier B.V.

Catalytic ethanolysis of Kraft lignin into high-value small-molecular chemicals over a nanostructured α-molybdenum carbide catalyst.

PubMed

Ma, Rui; Hao, Wenyue; Ma, Xiaolei; Tian, Ye; Li, Yongdan

2014-07-07

We report the complete ethanolysis of Kraft lignin over an α-MoC1-x /AC catalyst in pure ethanol at 280 °C to give high-value chemicals of low molecular weight with a maximum overall yield of the 25 most abundant liquid products (LP25) of 1.64 g per gram of lignin. The LP25 products consisted of C6 -C10 esters, alcohols, arenes, phenols, and benzyl alcohols with an overall heating value of 36.5 MJ kg(-1) . C6 alcohols and C8 esters predominated and accounted for 82 wt % of the LP25 products. No oligomers or char were formed in the process. With our catalyst, ethanol is the only effective solvent for the reaction. Supercritical ethanol on its own degrades Kraft lignin into a mixture of small molecules and molecular fragments of intermediate size with molecular weights in the range 700-1400, differing in steps of 58 units, which is the weight of the branched-chain linkage C3 H6 O in lignin. Hydrogen was found to have a negative effect on the formation of the low-molecular-weight products. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

2-Amino-2,3-dimethyl­butanamide

PubMed Central

Yin, Yongbiao

2010-01-01

The title compound, C6H14N2O, was synthesized by the reaction between 2-amino-2,3-dimethyl­butanonitrile and oil of vitriol (sulfuric acid). A racemic mixture of L- and R-2-amino-2,3-di­methyl­butanamide was characterized crystallographically. In the crystal structure, inter­molecular N—H⋯O hydrogen bonds link the two enanti­omers into a three-dimensional network. PMID:21579361

Foliar injury response of petunia and kidney bean to simultaneous and alternate exposures to ozone and pan

NASA Astrophysics Data System (ADS)

Nouchi, Isamu; Mayumi, Hirokazu; Yamazoe, Fumio

Petunia at about 6 weeks old and kidney bean at two growing stages (6-7 days old and 16-18 days old) were exposed separately to O 3, (0-0.40 ppm) and PAN (0-0.25 ppm) for 4 h and to the mixture for the same time. In addition, petunia was exposed to O, (0.10-0.40 ppm) and then PAN (0.010-0.040 ppm) for 4 h, respectively. Foliar injury of petunia and kidney bean in exposures to the mixtures of O 3 and PAN was significantly smaller than that induced by each oxidant, with the exception of PAN injury on young leaves of 16-18 day-old kidney bean. The percentage of foliar injury caused by either of the mixed pollutants decreased with an increase of the concentration of the other oxidant, and was found to approximate a logarithmic function of the combined pollutant concentrations expressed as O 3, minum PAN or vice versa. Alternate exposures caused no additive or synergistic injuries.

"Hexagonal molybdenum trioxide"--known for 100 years and still a fount of new discoveries.

PubMed

Lunk, Hans-Joachim; Hartl, Hans; Hartl, Monika A; Fait, Martin J G; Shenderovich, Ilya G; Feist, Michael; Frisk, Timothy A; Daemen, Luke L; Mauder, Daniel; Eckelt, Reinhard; Gurinov, Andrey A

2010-10-18

In 1906, the preparation of “molybdic acid hydrate” was published by Arthur Rosenheim. Over the past 40 years, a multitude of isostructural compounds, which exist within a wide phase range of the system MoO3−NH3−H2O, have been published. The reported molecular formulas of “hexagonal molybdenum oxide” varied from MoO3 to MoO3·0.33NH3 to MoO3·nH2O (0.09 ≤ n ≤ 0.69) to MoO3·mNH3·nH2O (0.09 ≤ m ≤ 0.20; 0.18 ≤ n ≤ 0.60). Samples, prepared by the acidification route were investigated using thermal analysis coupled online to a mass spectrometer for evolved gas analysis, X-ray powder diffraction, Fourier transform infrared, Raman, magic-angle-spinning 1H- and 15N NMR spectroscopy, and incoherent inelastic neutron scattering. A comprehensive characterization of these samples will lead to a better understanding of their structure and physical properties as well as uncover the underlying relationship between the various compositions. The synthesized polymeric parent samples can be represented by the structural formula (NH4)(x∞)(3)[Mo(y square 1−y)O(3y)(OH)(x)(H2O)(m−n)]·nH2O with 0.10 ≤ x ≤ 0.14, 0.84 ≤ y ≤ 0.88, and m + n ≥ 3 − x − 3y. The X-ray study of a selected monocrystal confirmed the presence of the well-known 3D framework of edge- and corner-sharing MoO6 octahedra. The colorless monocrystal crystallizes in the hexagonal system with space group P6(3)/m, Z = 6, and unit cell parameters of a = 10.527(1) Å, c = 3.7245(7) Å, V = 357.44(8) Å3, and ρ = 3.73 g·cm(−3). The structure of the prepared monocrystal can best be described by the structural formula (NH4)(0.13∞)(3)[Mo(0.86 square 0.14)O2.58(OH)0.13(H2O)(0.29−n)]·nH2O, which is consistent with the existence of one vacancy (square) for six molybdenum sites. The sample MoO3·0.326NH3·0.343H2O, prepared by the ammoniation of a partially dehydrated MoO3·0.170NH3·0.153H2O with dry gaseous ammonia, accommodates NH3 in the hexagonal tunnels, in addition to [NH4]+ cations and H2O. The “chimie douce” reaction of MoO3·0.155NH3·0.440H2O with a 1:1 mixture of NO/NO2 at 100 °C resulted in the synthesis of MoO3·0.539H2O. This material is of great interest as a host of various molecules and cations.

Durable and Rechargeable Antimicrobial Textiles

DTIC Science & Technology

2013-12-01

N -halamine Precursor Concentration (%) G ra ft in g Y ie ld ( % ) 0 100 200 300 400 500 600 700 800 900 1000 1100 1200...1300 C h lo rin e c o n te n t (p p m ) 80 90 100 110 120 0.0 0.2 0.4 0.6 0.8 1.0 Wet Pickup (%) G ra ft in g Y ie ld ( % ) C h lo rin e c o n te n ...temperature ( o C) C h lo rin e c o n te n t (p p m )

Optical and magnetic properties for metal halide-based organic-inorganic layered perovskites

NASA Astrophysics Data System (ADS)

Shikoh, Eiji; Ando, Yasuo; Era, Masanao; Miyazaki, Terunobu

2001-05-01

Layered perovskites (RNH 3) 2CuCl 4, where R was methyl-benzene C 6H 5-CH 2, 1-methyl-naphthalene 1-C 10H 9-CH 2, 1-propyl-naphthalene 1-C 10H 9-O(CH 2) 3 and 1-butyl-naphthalene 1-C 10H 9-O(CH 2) 4, were synthesized. These complexes showed ferromagnetism, with different Curie temperatures, TC, depending on the structure of the molecule. The change of TC by taking into account the overlap of the electronic states between the organic and the inorganic layers were discussed.

Synthesis of some 1,8-dioxoacridine carboxylic acid derivatives and the determination of their ionization constants in ethanol-water mixtures

NASA Astrophysics Data System (ADS)

Saygılı, Rukiye; Ulus, Ramazan; Yeşildağ, İbrahim; Kübra İnal, E.; Kaya, Muharrem; Murat Kalfa, O.; Zeybek, Bülent

2015-03-01

Four novel compounds of 1,8-dioxoacridine carboxylic acid derivatives (4-(3,3,6,6-tetramethyl-1,8-dioxo-9-phenyl-1,2,3,4,5,6,7,8-octahydroacridin-10(9H)-yl)benzoic acid, 4-(9-(4-cyanophenyl)-3,3,6,6-tetramethyl-1,8-dioxo-1,2,3,4,5,6,7,8-octahydroacridin-10(9H)-yl)benzoic acid, 4-(9-(4-hydroxyphenyl)-3,3,6,6-tetramethyl-1,8-dioxo-1,2,3,4,5,6,7,8-octahydroacridin-10(9H)-yl)benzoic acid, 4-(9-(2,4-dichlorophenyl)-3,3,6,6-tetramethyl-1,8-dioxo-1,2,3,4,5,6,7,8-octahydroacridin-10(9H)-yl)benzoic acid) were prepared by the reaction of the 4-substitute benzaldehyde (hydrogen, hydroxyl, cyano, and 2,4-dichloro), 4-aminobenzoic acid, and 5,5-dimethylcyclohexane-1,3-dione in the presence of p-dodecylbenzenesulfonic acid. They were characterized by using FT-IR, 1H-NMR, 13C-NMR, GC-MS spectroscopic techniques. The stoichiometric ionization constants of these compounds were determined in ethanol-water mixtures of 50%, 60% and 70% ethanol (v/v) by potentiometric titration method and the ionization constants were calculated with three different ways. The effects of solvent composition and substituent groups on ionization constants of 1,8-dioxoacridine carboxylic acids were also discussed.

Potential improvements aimed at high precision δ13C isotopic ratio determinations in CO2 mixtures using optical absorption spectrometry.

PubMed

Koulikov, Serguei; Assonov, Sergey; Fajgelj, Ales; Tans, Pieter

2018-07-01

The manuscript explores some advantages and limitations of laser based optical spectroscopy, aimed at achieving robust, high-reproducibility 13 C 16 O 2 and 12 C 16 O 2 ratio determinations on the VPDB-CO 2 δ 13 C scale by measuring the absorbance of line pairs of 13 C 16 O 2 and 12 C 16 O 2 . In particular, the sensitivities of spectroscopic lines to both pressure (P) and temperature (T) are discussed. Based on the considerations and estimations presented, a level of reproducibility of the 13 C 16 O 2 / 12 C 16 O 2 ratio determinations may be achieved of about 10 -6 . Thus one may establish an optical spectroscopic measurement technique for robust, high-precision 13 C 16 O 2 and 12 C 16 O 2 ratio measurements aimed at very low uncertainty. (Notably, creating such an optical instrument and developing technical solutions is beyond the scope of this paper.) The total combined uncertainty will also include the uncertainty component(s) related to the accuracy of calibration on the VPDB-CO 2 δ 13 C scale. Addressing high-accuracy calibrations is presently not straightforward - absolute numerical values of 13 C/ 12 C for the VPDB-CO 2 scale are not well known. Traditional stable isotope mass-spectrometry uses calibrations vs CO 2 evolved from the primary carbonate reference materials; which can hardly be used for calibrating commercial optical stable isotope analysers. In contrast to mass-spectrometry, the major advantage of the laser-based spectrometric technique detailed in this paper is its high robustness. Therefore one can introduce a new spectrometric δ 13 C characterisation method which, being once well-calibrated on the VPDB-CO 2 scale, may not require any further (re-)calibrations. This can be used for characterisation of δ 13 C in CO 2 -in-air mixtures with high precision and also with high accuracy. If this technique can be realised with the estimated long-term reproducibility (order of 10 -6 ), it could potentially serve as a more convenient Optical Transfer Standard (OTS), characterising large amounts of CO 2 gas mixtures on the VPDB-CO 2 δ 13 C scale without having to compare to carbonate-evolved CO 2 . Furthermore, if the OTS method proves to be successful, it might be considered for re-defining the VPDB-CO 2 δ 13 C-scale as the ratio of selected CO 2 spectroscopic absorbance lines measured at pre-defined T & P conditions. The approach can also be expanded to δ 18 O characterisation (using 16 O 12 C 18 O and 16 O 12 C 16 O absorbance lines) of CO 2 gas mixtures and potentially to other isotope ratios of other gases. Copyright © 2018 Elsevier B.V. All rights reserved.

Improving enzymatic hydrolysis of corn stover pretreated by ethylene glycol-perchloric acid-water mixture.

PubMed

He, Yu-Cai; Liu, Feng; Gong, Lei; Lu, Ting; Ding, Yun; Zhang, Dan-Ping; Qing, Qing; Zhang, Yue

2015-02-01

To improve the enzymatic saccharification of lignocellulosic biomass, a mixture of ethylene glycol-HClO4-water (88.8:1.2:10, w/w/w) was used for pretreating corn stover in this study. After the optimization in oil-bath system, the optimum pretreatment temperature and time were 130 °C and 30 min, respectively. After the saccharification of 10 g/L pretreated corn stover for 48 h, the saccharification rate was obtained in the yield of 77.4 %. To decrease pretreatment temperature and shorten pretreatment time, ethylene glycol-HClO4-water (88.8:1.2:10, w/w/w) media under microwave irradiation was employed to pretreat corn stover effectively at 100 °C and 200 W for 5 min. Finally, the recovered hydrolyzates containing glucose obtained from the enzymatic hydrolysis of pretreated corn stovers could be fermented into ethanol efficiently. These results would be helpful for developing a cost-effective pretreatment combined with enzymatic saccharification of cellulosic materials for the production of lignocellulosic ethanol.

Weakening of ice by magnesium perchlorate hydrate

USGS Publications Warehouse

Lenferinka, Hendrick J.; Durhama, William B.; Sternb, Laura A.; Patharec, Asmin V.

2013-01-01

We show that perchlorate hydrates, which have been detected at high circumpolar martian latitudes, have a dramatic effect upon the rheological behavior of polycrystalline water ice under conditions applicable to the North Polar Layered Deposits (NPLD). We conducted subsolidus creep tests on mixtures of ice and magnesium perchlorate hydrate, Mg(ClO4)2·6H2O (MP6), of 0.02, 0.05, 0.10, and 0.47 volume fraction MP6. We found these mixtures to be increasingly weak with increasing MP6 content. For mixtures with ⩽0.10 volume fraction MP6, we resolved a stress exponent of n ≈ 2 at low stresses transitioning to n ≈ 4 above 10 MPa. Scanning electron microscopy of deformed specimens revealed MP6 to be distributed as an interconnected film between ice grains. These results suggest that grain boundary sliding (GBS) may be enhanced with respect to pure ice. As the enhancement of GBS is expected in polycrystalline aggregates containing a few percent melt or otherwise weak material distributed along grain boundaries, the observed n ≈ 2 is consistent with the mutual accommodation of basal slip and GBS. If ice containing trace concentrations of MP6 is also much weaker than pure ice at low stresses, flow in the NPLD could be significantly enhanced, particularly at the warmer basal temperatures associated with higher martian obliquities.

Variations in the Strength of the Infrared Forbidden 2328.2 cm-1 Fundamental of Solid N2 in Binary Mixtures

NASA Technical Reports Server (NTRS)

Bernstein, Max P.; Sandford, Scott A.; Mead, Susan (Technical Monitor)

2002-01-01

We present the 2335-2325 cm(exp -1) infrared spectra and band positions, profiles, and strengths (A values) of solid nitrogen and binary mixtures of N2 with other molecules at 12 K. The data demonstrate that the strength of the infrared forbidden N2 fundamental near 2328 cm(exp -1) is moderately enhanced in the presence of NH3, strongly enhanced in the presence of H2O and very strongly enhanced in the presence of CO2, but is not significantly affected by CO, CH4, or O2. The mechanisms for the enhancements in N2-NH3 and N2-H2O mixtures are fundamentally different from those proposed for N2-CO2 mixtures. In the first case, interactions involving hydrogen-bonding are likely the cause. In the latter, a resonant exchange between the N2 stretching fundamental and the O-18=C-12 asymmetric stretch of O-18C-12O-16 is indicated. The implications of these results for several astrophysical issues are briefly discussed.

Prime Contract Awards Alphabetically by Contractor, State or Country, and Place. Part 18 (University of Virginia, Carsonville, Virginia - Zymark Corporation, Hopkinton, Massachusetts), FY1991

DTIC Science & Technology

1991-01-01

C 44 ) C4 04 444)c_ _) I LC.) InflQAQ -4 < -4 -4< a 4 c - I 0)-CI I~ 000 10) 1" W .) 0 0007 10 10 LA LAY) LADO I I aH0 HO cc.4-4r 0 n r -I0 07 nc oq 0...4 (D C) -. C-4 0 IN -, r) IN N4 I3U to 04 a c( 0v o00 E co o CL0 to0 Or. Mb" be - -0) -oIn 3 1 0 3 1.W4 00 LC L.N 1C,) ENc >-0 I-N 0.0 L 6--4 L...4N E c’ m.40704mmo7 41,07 00C 0)07 -4 W07 ENC 0 If w4 6 04 66 AS0) .=07 00o momI-4-.c) 00) 4--4.-4 -40 0(D al 064 - XN0 0)1 C6 8 I CO. H:30 00 U-4

Crystal structure, quantum mechanical investigation, IR and NMR spectroscopy of two new organic perchlorates: (C6H18N3)·(ClO4)3H2O (I) and (C9H11N2)·ClO4(II)

NASA Astrophysics Data System (ADS)

Bayar, I.; Khedhiri, L.; Soudani, S.; Lefebvre, F.; Ferretti, V.; Ben Nasr, C.

2018-06-01

The reaction of perchloric acid with 1-(2-aminoethyl)piperazine or 5,6-dimethyl-benzimidazole results in the formation of 1-(2-amonioethyl)piperazine-1,4-dium triperchlorate hydrate (C6H18N3)·(ClO4)3·H2O (I) or 5,6-dimethyl-benzylimidazolium perchlorate (C9H11N2)·ClO4(II). Both compounds were fully structurally characterized including single crystal X-ray diffraction analysis. Compound (I) crystallizes in the centrosymmetric triclinic space group P 1 bar with the lattice parameters a = 7.455 (2), b = 10.462 (2), c = 10.824 (2) Å, α = 80.832 (2), β = 88.243 (2), γ = 88.160 (2) °, Z = 2 and V = 832.77 (3) Å3. Compound (II) has been found to belong to the P21/c space group of the monoclinic system, with a = 7.590 (3), b = 9.266 (3), c = 16.503 (6) Å, β = 107.38 (2) °, V = 1107.69 (7) Å3 and Z = 4. The structures of (I) and (II) consist of slightly distorted [ClO4]- tetrahedra anions and 1-(2-amonioethyl)piperazine-1,4-dium trication (I) or 5,6-dimethyl-benzylimidazolium cations (II) and additionally a lattice water in (I). The crystal structures of (I) and (II) exhibit complex three-dimensional networks of H-bonds connecting all their components. In the atomic arrangement of (I), the ClO4- anions form corrugated chains, while in (II) the atomic arrangement exhibits wide pseudo-hexagonal channels of ClO4 tetrahedra including the organic entities. The lattice water serves as a link between pairs of cations and pairs of anions via several Osbnd H⋯O and N-H⋯O interactions in compound (I). The vibrational absorption bands were identified by infrared spectroscopy. These compounds were also investigated by solid-state 13C, 35Cl and 15N NMR spectroscopy. DFT calculations allowed the attribution of the IR and NMR bands. Intermolecular interactions were investigated by Hirshfeld surfaces. Electronic properties such as HOMO and LUMO energies were derived.

Maillard reaction products as antimicrobial components for packaging films.

PubMed

Hauser, Carolin; Müller, Ulla; Sauer, Tanja; Augner, Kerstin; Pischetsrieder, Monika

2014-02-15

Active packaging foils with incorporated antimicrobial agents release the active ingredient during food storage. Maillard reaction products (MRPs) show antimicrobial activity that is at least partially mediated by H2O2. De novo generation of H2O2 by an MRP fraction, extracted from a ribose/lysine Maillard reaction mixture by 85% ethanol, was monitored at three concentrations (1.6, 16.1, and 32.3g/L) and three temperatures (4, 25, and 37 °C) between 0 and 96 h, reaching a maximum of 335 μM H2O2 (32.3g/L, 37 °C, 96 h). The active MRP fraction (16.1g/L) completely inhibited the growth of Escherichia coli for 24h and was therefore incorporated in a polyvinyl acetate-based lacquer and dispersed onto a low-density polyethylene film. The coated film generated about 100 μM H2O2 and resulted in a log-reduction of >5 log-cycles against E. coli. Thus, MRPs can be considered as active ingredients for antimicrobial packaging materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

Liquid-liquid phase separation in atmospheric aerosol particles: dependence on organic functionalities and mixture complexity

NASA Astrophysics Data System (ADS)

Song, M.; Marcolli, C.; Krieger, U. K.; Zuend, A.; Peter, T.

2012-04-01

In the troposphere, aerosol particles undergo phase transitions such as deliquescence and efflorescence during humidity cycles (Marcolli and Krieger, 2006). In addition, interactions between organic and inorganic compounds lead to liquid-liquid phase separation (LLPS) (Ciobanu et al., 2009). Recent studies on a limited number of model systems have shown that oxygen-to-carbon ratios (O:C) of the organic aerosol fraction might be a good predictor for LLPS in mixed organic/ammonium sulfate (AS) particles (Bertram et al., 2011; Song et al., 2011). However, in order to corroborate this hypothesis experiments with an organic fraction that consists of a higher number of components with different O:C ratios and functional groups are needed. In order to determine the influence of O:C ratio, the specific organic functionalities and the mixture complexity on LLPS, we subjected organic/AS particles deposited on a hydrophobically coated substrate to relative humidity (RH) cycles and observed phase changes using optical microscopy and micro-Raman spectroscopy. To determine the influence of mixture complexity, we mixed together up to 10 organic compounds. We also prepared mixtures that were rich in different types of functional groups like polyols, aromatics and dicarboxylic acids which were identified from field measurements. We screened for a miscibility gap by varying the organic-to-inorganic ratio from 2:1 to 1:6. AS in the investigated single particles effloresced at 27 - 50 %RH and deliquesced at 72 - 79 %RH during humidity cycles. The occurrence of LLPS is determined to a high degree by the O:C of the organics: there was no LLPS for mixtures with O:C > 0.8 and there was always LLPS for mixtures with O:C < 0.57. In the range in between, we observed a dependence on the specific functional groups: a high share of aromatic functionalities shifts the range of O:C for which LLPS occurs to lower values. A correlation was also found for the onset RH of LLPS as a function of O:C. We did not find any dependence of LLPS on the complexity of the mixture. Overall, the RH range of coexistence of two liquid phases depends in first place on the O:C ratio of the particles and in second place also on the specific organic functionalities.

Online Compound-Specific δ13C and δD Determinations Using Laser Spectroscopy

NASA Astrophysics Data System (ADS)

Saad, N.; Hoffnagle, J.

2012-04-01

A unique laser spectroscopic approach for making online high-precision compound-specific isotope analysis (CSIA) of both δ13C and δD of the CO2 and H2O organic combustion products is described. The system consists of a gas chromatograph (GC) for the separation of an organic mixture coupled to a novel micro-fabricated microreactor (MFMR) for the complete combustion of each organic compound into CO2 and H2O and the precise measurements of δ13C in the CO2 gas and δ2H in the H2O vapor from the well established infrared spectrum of both gases, using an isotopic CO2 Cavity Ring-Down Spectroscopy (CRDS) analyzer and an isotopic H2O vapor CRDS analyzer, respectively. Light hydrocarbons are used as our test compounds in this study. The analyses of CH4, C2H6 and C3H8 for δ13C and δ2H values resulted in precisions of SD(δ13C)<1‰ and SD(δ2H)<2‰, respectively. These results were further compared to the gold standard method using Dual Inlet IRMS (DI-IRMS) and showed excellent agreements in isotopic measurements. The preliminary results presented here pave the way for a single CRDS analyzer-based system that simultaneously measures δ13C and δD, is field-deployable, less costly and necessitates less operator expertise than IRMS-based systems.

(η6-Benzene)(carbonato-κ2 O,O′)[di­cyclohex­yl(naphthalen-1-ylmeth­yl)phosphane-κP]ruthenium(II) chloro­form tris­olvate

PubMed Central

Gowrisankar, Saravanan; Neumann, Helfried; Spannenberg, Anke; Beller, Matthias

2014-01-01

The title compound, [Ru(CO3)(η6-C6H6){(C6H11)2P(CH2C10H7)}]·3CHCl3, was synthesized by carbonation of [RuCl2(η6-C6H6){(C6H11)2P(CH2C10H7)}] with NaHCO3 in methanol at room temperature. The RuII atom is surrounded by a benzene ligand, a chelating carbonate group and a phosphane ligand in a piano-stool configuration. The crystal packing is consolidated by C—H⋯O and C—H⋯Cl hydrogen-bonding inter­actions between adjacent metal complexes and between the complexes and the solvent mol­ecules. The asymmetric unit contains one metal complex and three chloro­form solvent mol­ecules of which only one was modelled. The estimated diffraction contributions of the other two strongly disordered chloro­form solvent mol­ecules were substracted from the observed diffraction data using the SQUEEZE procedure in PLATON [Spek (2009 ▶). Acta Cryst. D65, 148–155]. PMID:25161531

Hydrothermal Syntheses and Structures of Three-Dimensional Oxo-fluorovanadium Phosphates: [H 2N(C 2H 4) 2NH 2] 0.5[(VO) 4V(HPO 4) 2(PO 4) 2F 2(H 2O) 4] · 2H 2O and K 2[(VO) 3(PO 4) 2F 2(H 2O)] · H 2O

NASA Astrophysics Data System (ADS)

Bonavia, Grant; Haushalter, R. C.; Zubieta, Jon

1996-11-01

The hydrothermal reactions of FPO3H2with vanadium oxides result in the incorporation of fluoride into V-P-O frameworks as a consequence of metal-mediated hydrolysis of the fluorophosphoric acid to produce F-and PO3-4. By exploiting this convenient source of F-, two 3-dimensional oxo-fluorovanadium phosphate phases were isolated, [H2N(C2H4)2NH2]0.5[(VO)4V(HOP4)2(PO4)2F2(H2O)4) · 2H2O (1 · 2H2O) and K2[(VO)3(PO4)2F2(H2O)] · H2O (2 · H2O). Both anionic frameworks contain (VIVO)-F--phosphate layers, with confacial bioctahedral {(VIVO)2FO6} units as the fundamental motif. In the case of 1, the layers are linked through {VIIIO6} octahedra, while for 2 the interlayer connectivity is provided by edge-sharing {(VIVO)2F2O6} units. Crystal data are 1 · 2H2O, CH10FN0.5O13P2V2.5, monoclinicC2/m,a= 18.425(4) Å,c= 8.954(2) Å, β = 93.69(2)0,V= 1221.1(4) Å3,Z= 4,Dcalc= 2.423 g cm-3; 2 · H2O, H4F2K2O13P2V3, triclinicPoverline1,a= 7.298(1) Å,b= 8.929(2) Å,c = 10.090(2) Å, α = 104.50(2)0, β = 100.39(2)0, δ = 92.13(2)0,V= 623.8(3) Å3,Z= 2,Dcalc= 2.891 g cm-3.

Experimental Determination of Solubilities of Sodium Polyborates In MgCl 2 Solutions: Solubility Constant of Di-Sodium Hexaborate Tetrahydrate, and Implications For the Diagenetic Formation of Ameghinite

DOE PAGES

Xiong, Yongliang; Kirkes, Leslie; KNOX, Jandi; ...

2017-11-01

In this paper, solubility measurements were conducted for sodium polyborates in MgCl 2 solutions at 22.5 ± 0.5 °C. According to solution chemistry and XRD patterns, di-sodium tetraborate decahydrate (borax) dissolves congruently, and is the sole solubility-controlling phase, in a 0.01 mol/kg MgCl 2 solution: Na 2B 4O 7•10H 2O(cr) ⇌ 2Na + + 4B(OH) 4 + 2H + + H 2O(l). However, in a 0.1 mol/kg MgCl 2 solution borax dissolves incongruently and is in equilibrium with di-sodium hexaborate tetrahydrate: 2Na 2B 6O 10•4H 2O(cr) + 2Na + + 23H 2O(l) ⇌ 3Na 2B 4O 7•10H 2O(cr) + 2Hmore » +. In this study, the equilibrium constant (log K 0) for Reaction 2 at 25 °C and infinite dilution was determined to be –16.44 ± 0.13 (2σ) based on the experimental data and the Pitzer model for calculations of activity coefficients of aqueous species. In accordance with the log K 0 for Reaction 1 from a previous publication from this research group, and log K 0 for Reaction 2 from this study, the equilibrium constant for dissolution of di-sodium hexaborate tetrahydrate at 25 °C and at infinite dilution, Na 2B 6O 10•4H 2O(cr) + 10H 2O(l) ⇌ 2Na + + 6B(OH) 4 - + 4H + was derived to be –45.42 ± 0.16 (2σ). The equilibrium constants determined in this study can find applications in many fields. For example, in the field of nuclear waste management, the formation of di-sodium hexaborate tetrahydrate in brines containing magnesium will decrease borate concentrations, making less borate available for interactions with Am(III). In the field of experimental investigations, based on the equilibrium constant for Reaction 2, the experimental systems can be controlled in terms of acidity around neutral pH by using the equilibrium assemblage of borax and di-sodium hexaborate tetrahydrate at 25 °C. As salt lakes and natural brines contain both borate and magnesium as well as sodium, the formation of sodium hexaborate tetrahydrate may influence the chemical evolution of salt lakes and natural brines. Di-sodium hexaborate tetrahydrate is a polymorph of the mineral ameghinite [chemical formula Na 2B 6O 10•4H 2O; structural formula NaB 3O 3(OH) 4 or Na 2B 6O 6(OH) 8]. Finally, di-sodium hexaborate tetrahydrate could be a precursor of ameghinite and could be transformed when borate deposits are subject to diagenesis.« less

Experimental Determination of Solubilities of Sodium Polyborates In MgCl 2 Solutions: Solubility Constant of Di-Sodium Hexaborate Tetrahydrate, and Implications For the Diagenetic Formation of Ameghinite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiong, Yongliang; Kirkes, Leslie; KNOX, Jandi

In this paper, solubility measurements were conducted for sodium polyborates in MgCl 2 solutions at 22.5 ± 0.5 °C. According to solution chemistry and XRD patterns, di-sodium tetraborate decahydrate (borax) dissolves congruently, and is the sole solubility-controlling phase, in a 0.01 mol/kg MgCl 2 solution: Na 2B 4O 7•10H 2O(cr) ⇌ 2Na + + 4B(OH) 4 + 2H + + H 2O(l). However, in a 0.1 mol/kg MgCl 2 solution borax dissolves incongruently and is in equilibrium with di-sodium hexaborate tetrahydrate: 2Na 2B 6O 10•4H 2O(cr) + 2Na + + 23H 2O(l) ⇌ 3Na 2B 4O 7•10H 2O(cr) + 2Hmore » +. In this study, the equilibrium constant (log K 0) for Reaction 2 at 25 °C and infinite dilution was determined to be –16.44 ± 0.13 (2σ) based on the experimental data and the Pitzer model for calculations of activity coefficients of aqueous species. In accordance with the log K 0 for Reaction 1 from a previous publication from this research group, and log K 0 for Reaction 2 from this study, the equilibrium constant for dissolution of di-sodium hexaborate tetrahydrate at 25 °C and at infinite dilution, Na 2B 6O 10•4H 2O(cr) + 10H 2O(l) ⇌ 2Na + + 6B(OH) 4 - + 4H + was derived to be –45.42 ± 0.16 (2σ). The equilibrium constants determined in this study can find applications in many fields. For example, in the field of nuclear waste management, the formation of di-sodium hexaborate tetrahydrate in brines containing magnesium will decrease borate concentrations, making less borate available for interactions with Am(III). In the field of experimental investigations, based on the equilibrium constant for Reaction 2, the experimental systems can be controlled in terms of acidity around neutral pH by using the equilibrium assemblage of borax and di-sodium hexaborate tetrahydrate at 25 °C. As salt lakes and natural brines contain both borate and magnesium as well as sodium, the formation of sodium hexaborate tetrahydrate may influence the chemical evolution of salt lakes and natural brines. Di-sodium hexaborate tetrahydrate is a polymorph of the mineral ameghinite [chemical formula Na 2B 6O 10•4H 2O; structural formula NaB 3O 3(OH) 4 or Na 2B 6O 6(OH) 8]. Finally, di-sodium hexaborate tetrahydrate could be a precursor of ameghinite and could be transformed when borate deposits are subject to diagenesis.« less

Aspects of Supercritical Turbulence: Direct Numerical Simulation of O2/H2 and C7H16/N2 Temporal Mixing Layers

NASA Technical Reports Server (NTRS)

Bellan, J.; Okongo, N. A.; Harstad, K. G.; Hutt, John (Technical Monitor)

2002-01-01

Results from Direct Numerical Simulations of temporal, supercritical mixing layers for two species systems are analyzed to elucidate species-specific turbulence aspects. The two species systems, O2/H2 and C7HG16/N2, have different thermodynamic characteristics; thus, although the simulations are performed at similar reduced pressure (ratio of the pressure to the critical pressure), the former system is dose to mixture ideality and has a relatively high solubility with respect to the latter, which exhibits strong departures from mixture ideality Due to the specified, smaller initial density stratification, the C7H16/N2 layers display higher growth and increased global molecular mixing as well as larger turbulence levels. However, smaller density gradients at the transitional state for the O2/H2 system indicate that on a local basis, the layer exhibits an enhanced mixing, this being attributed to the increased solubility and to mixture ideality. These thermodynamic features are shown to affect the irreversible entropy production (i.e. the dissipation), which is larger for the O2/H2 layer and is primarily concentrated in high density-gradient magnitude regions that are distortions of the initial density stratification boundary. In contrast, the regions of largest dissipation in the C7H16/N2 layer are located in high density-gradient magnitude regions resulting from the mixing of the two fluids.

Modeling of Combined Processing Steps for Reducing Escherichia coli O157:H7 Populations in Apple Cider

PubMed Central

Uljas, Heidi E.; Schaffner, Donald W.; Duffy, Siobain; Zhao, Lihui; Ingham, Steven C.

2001-01-01

Probabilistic models were used as a systematic approach to describe the response of Escherichia coli O157:H7 populations to combinations of commonly used preservation methods in unpasteurized apple cider. Using a complete factorial experimental design, the effect of pH (3.1 to 4.3), storage temperature and time (5 to 35°C for 0 to 6 h or 12 h), preservatives (0, 0.05, or 0.1% potassium sorbate or sodium benzoate), and freeze-thaw (F-T; −20°C, 48 h and 4°C, 4 h) treatment combinations (a total of 1,600 treatments) on the probability of achieving a 5-log10-unit reduction in a three-strain E. coli O157:H7 mixture in cider was determined. Using logistic regression techniques, pH, temperature, time, and concentration were modeled in separate segments of the data set, resulting in prediction equations for: (i) no preservatives, before F-T; (ii) no preservatives, after F-T; (iii) sorbate, before F-T; (iv) sorbate, after F-T; (v) benzoate, before F-T; and (vi) benzoate, after F-T. Statistical analysis revealed a highly significant (P < 0.0001) effect of all four variables, with cider pH being the most important, followed by temperature and time, and finally by preservative concentration. All models predicted 92 to 99% of the responses correctly. To ensure safety, use of the models is most appropriate at a 0.9 probability level, where the percentage of false positives, i.e., falsely predicting a 5-log10-unit reduction, is the lowest (0 to 4.4%). The present study demonstrates the applicability of logistic regression approaches to describing the effectiveness of multiple treatment combinations in pathogen control in cider making. The resulting models can serve as valuable tools in designing safe apple cider processes. PMID:11133437

Modeling of combined processing steps for reducing Escherichia coli O157:H7 populations in apple cider.

PubMed

Uljas, H E; Schaffner, D W; Duffy, S; Zhao, L; Ingham, S C

2001-01-01

Probabilistic models were used as a systematic approach to describe the response of Escherichia coli O157:H7 populations to combinations of commonly used preservation methods in unpasteurized apple cider. Using a complete factorial experimental design, the effect of pH (3. 1 to 4.3), storage temperature and time (5 to 35 degrees C for 0 to 6 h or 12 h), preservatives (0, 0.05, or 0.1% potassium sorbate or sodium benzoate), and freeze-thaw (F-T; -20 degrees C, 48 h and 4 degrees C, 4 h) treatment combinations (a total of 1,600 treatments) on the probability of achieving a 5-log(10)-unit reduction in a three-strain E. coli O157:H7 mixture in cider was determined. Using logistic regression techniques, pH, temperature, time, and concentration were modeled in separate segments of the data set, resulting in prediction equations for: (i) no preservatives, before F-T; (ii) no preservatives, after F-T; (iii) sorbate, before F-T; (iv) sorbate, after F-T; (v) benzoate, before F-T; and (vi) benzoate, after F-T. Statistical analysis revealed a highly significant (P < 0.0001) effect of all four variables, with cider pH being the most important, followed by temperature and time, and finally by preservative concentration. All models predicted 92 to 99% of the responses correctly. To ensure safety, use of the models is most appropriate at a 0.9 probability level, where the percentage of false positives, i.e., falsely predicting a 5-log(10)-unit reduction, is the lowest (0 to 4.4%). The present study demonstrates the applicability of logistic regression approaches to describing the effectiveness of multiple treatment combinations in pathogen control in cider making. The resulting models can serve as valuable tools in designing safe apple cider processes.

Dry Reforming of Methane in a Gliding Arc Plasmatron: Towards a Better Understanding of the Plasma Chemistry.

PubMed

Cleiren, Emelie; Heijkers, Stijn; Ramakers, Marleen; Bogaerts, Annemie

2017-10-23

Dry reforming of methane (DRM) in a gliding arc plasmatron is studied for different CH 4 fractions in the mixture. The CO 2 and CH 4 conversions reach their highest values of approximately 18 and 10 %, respectively, at 25 % CH 4 in the gas mixture, corresponding to an overall energy cost of 10 kJ L -1 (or 2.5 eV per molecule) and an energy efficiency of 66 %. CO and H 2 are the major products, with the formation of smaller fractions of C 2 H x (x=2, 4, or 6) compounds and H 2 O. A chemical kinetics model is used to investigate the underlying chemical processes. The calculated CO 2 and CH 4 conversion and the energy efficiency are in good agreement with the experimental data. The model calculations reveal that the reaction of CO 2 (mainly at vibrationally excited levels) with H radicals is mainly responsible for the CO 2 conversion, especially at higher CH 4 fractions in the mixture, which explains why the CO 2 conversion increases with increasing CH 4 fraction. The main process responsible for CH 4 conversion is the reaction with OH radicals. The excellent energy efficiency can be explained by the non-equilibrium character of the plasma, in which the electrons mainly activate the gas molecules, and by the important role of the vibrational kinetics of CO 2 . The results demonstrate that a gliding arc plasmatron is very promising for DRM. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparison of effects of ProSeal LMA™ laryngeal mask airway cuff inflation with air, oxygen, air:oxygen mixture and oxygen:nitrous oxide mixture in adults: A randomised, double-blind study.

PubMed

Sharma, Mona; Sinha, Renu; Trikha, Anjan; Ramachandran, Rashmi; Chandralekha, C

2016-08-01

Laryngeal mask airway (LMA) cuff pressure increases when the air is used for the cuff inflation during oxygen: nitrous oxide (O2:N2O) anaesthesia, which may lead to various problems. We compared the effects of different gases for ProSeal LMA™ (PLMA) cuff inflation in adult patients for various parameters. A total of 120 patients were randomly allocated to four groups, according to composition of gases used to inflate the PLMA cuff to achieve 40 cmH2 O cuff pressure, air (Group A), 50% O2 :air (Group OA), 50% O2:N2O (Group ON) and 100% O2 (Group O). Cuff pressure, cuff volume and ventilator parameters were monitored intraoperatively. Pharyngolaryngeal parameters were assessed at 1, 2 and 24 h postoperatively. Statistical analysis was performed using ANOVA, Fisher's exact test and step-wise logistic regression. Cuff pressure significantly increased at 10, 15 and 30 min in Group A, OA and O from initial pressure. Cuff pressure decreased at 5 min in Group ON (36.6 ± 3.5 cmH2 O) (P = 0.42). PLMA cuff volume increased in Group A, OA, O, but decreased in Group ON (6.16 ± 2.8 ml [P < 0.001], 4.7 ± 3.8 ml [P < 0.001], 1.4 ± 3.19 ml [P = 0.023] and - 1.7 ± 4.9 ml [P = 0.064], respectively), from basal levels. Ventilatory parameters were comparable in all four groups. There was no significant association between sore throat and cuff pressure, with odds ratio 1.002. Cuff inflation with 50% O2:N2O mixture provided more stable cuff pressure in comparison to air, O2 :air, 100% O2 during O2:N2O anaesthesia. Ventilatory parameters did not change with variation in PLMA cuff pressure. Post-operative sore throat had no correlation with cuff pressure.

Effectiveness of Active Packaging on Control of Escherichia Coli O157:H7 and Total Aerobic Bacteria on Iceberg Lettuce.

PubMed

Lu, Haixia; Zhu, Junli; Li, Jianrong; Chen, Jinru

2015-06-01

Contaminated leafy green vegetables have been linked to several outbreaks of human gastrointestinal infections. Antimicrobial interventions that are adoptable by the fresh produce industry for control of pathogen contamination are in great demand. This study was undertaken to evaluate the efficacy of sustained active packaging on control of Escherichia coli O157:H7 and total aerobic bacteria on lettuce. Commercial Iceberg lettuce was inoculated with a 3-strain mixture of E. coli O157:H7 at 10(2) or 10(4) CFU/g. The contaminated lettuce and un-inoculated controls were placed respectively in 5 different active packaging structures. Traditional, nonactive packaging structure was included as controls. Packaged lettuce was stored at 4, 10, or 22 °C for 3 wk and sampled weekly for the population of E. coli O157:H7 and total aerobic bacteria. Results showed that packaging structures with ClO2 generator, CO2 generator, or one of the O2 scavengers effectively controlled the growth of E. coli O157:H7 and total aerobic bacteria under all storage conditions. Packaging structure with the ClO2 generator was most effective and no E. coli O157:H7 was detected in samples packaged in this structure except for those that were inoculated with 4 log CFU/g of E. coli O157:H7 and stored at 22 °C. Packaging structures with an oxygen scavenger and the allyl isothiocyanate generator were mostly ineffective in control of the growth of the bacteria on Iceberg lettuce. The research suggests that some of the packaging structures evaluated in the study can be used to control the presence of foodborne pathogens on leafy green vegetables. © 2015 Institute of Food Technologists®

Decontamination of green onions and baby spinach by vaporized ethyl pyruvate.

PubMed

Durak, M Zeki; Churey, John J; Gates, Matthew; Sacks, Gavin L; Worobo, Randy W

2012-06-01

Foodborne illnesses associated with fresh produce continue to be a major concern as consumer demand for healthier and nonthermally processed food increases. The objective of this study was to evaluate vaporized ethyl pyruvate (EP; CAS 617-35-6) as a safe alternative antimicrobial agent for the decontamination of Escherichia coli O157:H7 on green onions and spinach. Baby spinach leaves and green onions were inoculated with a five-strain cocktail of E. coli O157:H7 (pGFP) by the dipping method. Samples were treated with concentrations of 0, 42, 105, and 420 mg/liter vaporized EP in a 2.6-liter enclosed container. The efficacy of EP vapors for reducing E. coli O157:H7((GFP)) populations on green onions and baby spinach at 4 and 10°C was monitored for 7 and 5 days, respectively. The lowest EP concentration (42 mg/liter) resulted in a 1.7-log reduction of E. coli O157:H7((GFP)) on green onions after 7 days at 4°C and a 1.9-log reduction after 5 days at 10°C (P < 0.05). In baby spinach, the same concentration resulted in 0.9-log and 1.4-log reductions (P < 0.05) of E. coli O157:H7((GFP)) after 7 days at 4°C and 5 days at 10°C, respectively. On green onions, the highest concentration of EP (420 mg/liter) reduced the population of E. coli O157:H7((GFP)) by >4.7 log CFU/g after 7 days at 4°C and 5 days at 10°C. The same concentration was also effective for reducing E. coli O157:H7((GFP)) populations in baby spinach by 4.3 log CFU/g after 7 days at 4°C and by >6.5 log CFU/g after 3 days at 10°C. Although the successful EP treatments minimally affected the sensory attributes of green onions, the treatments resulted in significant changes in the sensory attributes of baby spinach samples stored at 4 and 10°C. These results indicate that EP is an effective antimicrobial that could be used to enhance the safety of fresh produce depending on the sensory characteristics of the product.

Formation, isomerization, and derivatization of Keggin tungstoaluminates.

PubMed

Cowan, J J; Bailey, A J; Heintz, R A; Do, B T; Hardcastle, K I; Hill, C L; Weinstock, I A

2001-12-17

Trends in the stability of alpha- and beta-Keggin heteropolytungstates of the second-row main-group heteroatoms Al(III), Si(IV), and P(V) are elaborated by data that establish the roles of kinetic and thermodynamic control in the formation and isomerization of Keggin tungstoaluminates. Slow, room-temperature co-condensation of Al(III) and W(VI) (2:11 molar ratio) in water gives a pH 7 solution containing beta(1) and beta(2) isomers of [Al(AlOH(2))W(11)O(39)](6)(-) (beta(1)- and beta(2)-1). Partial equilibration of this kinetic product mixture by gentle heating (2 h at 100 degrees C) or, alternatively, co-condensation of Al(III) and W(VI) for 2.5 h at 100 degrees C both give mixtures of beta(2)-, beta(3)-, and alpha-1. Full equilibration, by prolonged heating (25 days at 100 degrees C), gives an isomerically pure solution of alpha-1, thus demonstrating that isomerization occurs in the direction beta(1) --> beta(2) --> beta(3) --> alpha. Furthermore, kinetically controlled conversions of 1 to H(5)[AlW(12)O(40)] (2)-achieved by heating pH 0-0.2 solutions of 1 for 5 days at 100 degrees C-occur with retention of isomeric integrity, such that alpha-1 is converted to alpha-2 (92%; 8% beta), while mixtures of beta(2)- and beta(3)-1 are converted to beta-2 (87%; 13% alpha). These data, when combined with previously reported observations (equilibria between alpha- and beta-2, kinetically controlled hydrolyses of alpha-2 to alpha-[AlW(11)O(39)](9)(-) (alpha-3) and of beta-2 to beta(2)-3, and equilibria between beta(3)- and alpha-3), provide a comprehensive picture regarding the roles of kinetic and thermodynamic control. Finally, a general method for preparation of the isomerically pure derivatives alpha-K(9)(-)(n)()[AlM(n)()(+)W(11)O(39)] (4), M(n)()(+) = Al(III), [V(IV)O](2+), [V(V)O](3+), Mn(II), Mn(III), Mn(IV), Co(II), and Co(III), is provided. The presence of Mn(IV) is confirmed by cyclic voltammetry, pK(a) values of the aquo ligands on 4 are determined by pH titration, and the isomeric structure of these derivatives is established by (27)Al, (51)V, and (183)W NMR and IR spectroscopies and X-ray crystallography.

Electronically Strongly Coupled Divinylheterocyclic-Bridged Diruthenium Complexes.

PubMed

Pfaff, Ulrike; Hildebrandt, Alexander; Korb, Marcus; Oßwald, Steffen; Linseis, Michael; Schreiter, Katja; Spange, Stefan; Winter, Rainer F; Lang, Heinrich

2016-01-11

Complexes [{Ru(CO)Cl(PiPr3 )2 }2 (μ-2,5-(CH-CH)2 -(c) C4 H2 E] (E=NR; R=C6 H4 -4-NMe2 (10 a), C6 H4 -4-OMe (10 b), C6 H4 -4-Me (10 c), C6 H5 (10 d), C6 H4 -4-CO2 Et (10 e), C6 H4 -4-NO2 (10 f), C6 H3 -3,5-(CF3 )2 (10 g), CH3 (11); E=O (12), S (13)) are discussed. The solid state structures of four alkynes and two complexes are reported. (Spectro)electrochemical studies show a moderate influence of the nature of the heteroatom and the electron-donating or -withdrawing substituents R in 10 a-g on the electrochemical and spectroscopic properties. The CVs display two consecutive one-electron redox events with ΔE°'=350-495 mV. A linear relationship between ΔE°' and the σp Hammett constant for 10 a-f was found. IR, UV/Vis/NIR and EPR studies for 10(+) -13(+) confirm full charge delocalization over the {Ru}CH-CH-heterocycle-CH-CH{Ru} backbone, classifying them as Class III systems according to the Robin and Day classification. DFT-optimized structures of the neutral complexes agree well with the experimental ones and provide insight into the structural consequences of stepwise oxidations. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Magnesiothermic reduction for direct synthesis of Ti-Nb alloy at 1073 K (800 °C)

NASA Astrophysics Data System (ADS)

Choi, Kyunsuk; Lee, Kwang Hee; Ali, Basit; Choi, Sang-Hoon; Park, Kyoung-Tae; Sohn, Il

2017-09-01

Direct fabrication of titanium (Ti) and niobium (Nb) alloys by direct magnesiothermic reduction from the respective initial metal oxides and complex oxides has been studied. TiO2, Nb2O5, and complex TiNb2O7 oxides were used as raw materials with Mg used as a reductant. To ensure a high chemical potential of the reactants to drive the spontaneous magnesiothermic reduction of the oxide mixtures, excess Mg five times higher than the required stoichiometric molar ratio was added. Samples were heated in a glove box under recycled and purified Ar atmosphere at 1073 K (800 °C) for 10 h. After the reduction of TiO2, intermediate oxide phases of Ti6O could still be observed, but reduction of Nb2O5 and TiNb2O7 showed metallic Nb and Ti-Nb to be present with negligible oxides according to the scanning electron microscope-energy dispersive spectroscopy and x ray diffraction analysis. This indicated that direct fabrication of Ti-Nb alloys through a complex TiNb2O7 oxide is possible and can be more efficient than alloying pure metallic elements of Ti and Nb.

Kinetic and mechanistic studies of reactive intermediates in photochemical and transition metal-assisted oxidation, decarboxylation and alkyl transfer reactions

NASA Astrophysics Data System (ADS)

Carraher, Jack McCaslin

Reactive species like high-valent metal-oxo complexes and carbon and oxygen centered radicals are important intermediates in enzymatic systems, atmospheric chemistry, and industrial processes. Understanding the pathways by which these intermediates form, their relative reactivity, and their fate after reactions is of the utmost importance. Herein are described the mechanistic detail for the generation of several reactive intermediates, synthesis of precursors, characterization of precursors, and methods to direct the chemistry to more desirable outcomes yielding 'greener' sources of commodity chemicals and fuels. High-valent Chromium from Hydroperoxido-Chromium(III). The decomposition of pentaaquahydroperoxido chromium(III) ion (hereafter Cr aqOOH2+) in acidic aqueous solutions is kinetically complex and generates mixtures of products (Craq3+, HCrO 4-, H2O2, and O2). The yield of high-valent chromium products (known carcinogens) increased from a few percent at pH 1 to 70 % at pH 5.5 (near biological pH). Yields of H 2O2 increased with acid concentration. The reproducibility of the kinetic data was poor, but became simplified in the presence of H2O2 or 2,2‧-azinobis(3-ethylbenzothiazoline-6-sulfonate) dianion (ABTS2-). Both are capable of scavenging strongly oxidizing intermediates). The observed rate constants (pH 1, [O2] ≤ 0.03 mM) in the presence of these scavengers are independent of [scavenger] and within the error are the same (k,ABTS2- = (4.9 +/- 0.2) x 10-4 s-1 and kH2O2 = (5.3 +/- 0.7) x 10-4 s-1); indicating involvement of the scavengers in post-rate determining steps. In the presence of either scavenger, decomposition of CrOOH2+ obeyed a two-term rate law, k obs / s-1 = (6.7 +/- 0.7) x 10-4 + (7.6 +/- 1.1) x 10-4 [H+]. Effect of [H+] on the kinetics and the product distribution, cleaner kinetics in the presence of scavengers, and independence of kobs on [scavenger] suggest a dual-pathway mechanism for the decay of Craq OOH2+. The H+-catalyzed path leads to the dissociation of H2O2 from Cr(III), while in the H+-independent reaction, CraqOOH2+ is transformed to Cr(V). Both scavengers rapidly remove Cr(V) and simplify both the kinetics and products by impeding formation of Cr(IV, V, VI). Syntheses, Reactivity, and Thermodynamic Considerations LRhR2+. Macrocyclic rhodium(II) complexes LRh(H 2O)2+ (L = L1= cyclam and L2 = meso-Me6-cyclam) react with alkyl hydroperoxides R(CH3)2COOH to generate the corresponding rhodium(III) alkyls LRh(H2O)R2+ (R = CH3, C2 H5, PhCH2). Methyl and benzyl complexes can also be prepared by bimolecular group transfer from alkyl cobaloximes (dmgX) 2(H2O)CoR (where R = CH3, CH2Ph and dmgX is either dimethylglyoxime or a BF2-capped derivative of dmg) to LRh(H2O)2+. When R = C2H5, C3H7 or C4H9, the mechanism changes from group transfer to hydrogen atom abstraction from the coordinated alkyl and produces LRh(H2O)H2+ and an a-olefin. The new LRh(H2O)R2+ complexes were characterized by solution NMR and by crystal structure analysis. They exhibit great stability in aqueous solution at room temperature, but undergo efficient Rh-C bond cleavage upon photolysis. 'Green' Model for Decarboxylation of Biomass Derived Acids via Photolysis of in situ formed Metal-Carboxylate Complexes. Photolysis of aqueous solutions containing propionic acid and Fe 3+ aq in the absence of oxygen generates a mixture of hydrocarbons (ethane, ethylene and butane), carbon dioxide, and Fe2+. Photolysis in the presence of O2 yields catalytic amounts of hydrocarbon products. When halide ions are present during photolysis; nearly quantitative yields of ethyl halides are produced via extraction of a halide atom from FeX2+ by ethyl radical. The rate constants for ethyl radical reactions with FeCl2+ (k = 4.0 (+/- 0.5) x 106 M-1s-1) and with FeBr 2+ (k = 3.0 (+/- 0.5) x 107 M-1s -1) were determined via competition reactions. Irradiation of solutions containing aqueous Cu2+ salts and linear carboxylic acids yield alpha-olefins selectively. This process is made catalytic by the introduction of O2. Photochemical decarboxylation of propionic acid in the presence of Cu2+ generates ethylene and Cu +. Longer-chain acids also yield alpha olefins as exclusive products. In the absence of continued purging with O2 to aid removal of olefin, Cu+(olefin) complexes accumulate and catalytic activity slows dramatically due to depletion of Cu2+. The results underscore the profound effect that the choice of metal ions, the medium, and reaction conditions exert on the photochemistry of carboxylic acids. Free Oxygen Atom in Solution from 4-Benzoylpyridine N-Oxide Excited Singlet. Photolysis of 4-benzoylpyridine N-oxide (BPyO) in the presence of quenchers of the triplet excited state produces up to 41% O(3P) (as determined by generation of ethylene upon scavenging with cyclopentene). In the absence of 3BPyO* quenchers a maximum of 13% O(3P) relative to consumed BPyO is obtained. The remaining products are hydroxylated-4-benzoylpyridine and 4-benzoylpyridine. Additionally, the rate of BPyO consumption (as determined by UV-vis) decreases in the presence of 3BPyO* quenching agents. Second order rate constants for 3BPyO* quenching were determined. A mechanism for photochemical deoxygenation of BPyO is proposed on the basis of kinetic data and product distribution under various conditions. Additionally, comparisons are made between the observed intermediates and similar triplet excited states and radical anions.

Nanoporous graphene obtained by hydrothermal process in H2O2 and its application for supercapacitors

NASA Astrophysics Data System (ADS)

Lv, Jinlong; Liang, Tongxiang

2016-08-01

Nanohole graphene oxide (NHGO) was obtained in a homogeneous aqueous mixture of graphene oxide (GO) and H2O2 at 120 °C. Supercapacitors were fabricated as the electrode material by using NHGO. A specific capacitance of 240.1 F g-1 was obtained at a current density of 1 A g-1 in 6 m KOH electrolyte and specific capacitance remained 193.6 F g-1 at the current density of 20 A g-1. This was attributed to reducing the inner space between the double-layers, enhanced ion diffusion and large specific surface area. Supercapacitor prepared with NHGO electrodes also exhibited an excellent cycle stability.

ECO2N V2.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Lehua; Spycher, Nicolas; Doughty, Christine

2015-02-01

ECO2N V2.0 is a fluid property module for the TOUGH2 simulator (Version 2.1) that was designed for applications to geologic sequestration of CO2 in saline aquifers and enhanced geothermal reservoirs. ECO2N V2.0 is an enhanced version of the previous ECO2N V1.0 module (Pruess, 2005). It expands the temperature range up to about 300oC whereas V1.0 can only be used for temperatures below about 110oC. V2.0 includes a comprehensive description of the thermodynamic and thermophysical properties of H2O - NaCl - CO2 mixtures, that reproduces fluid properties largely within experimental error for the temperature, pressure and salinity conditions 10 °C 109oC). In the transition range (99-109oC), a smooth interpolation is applied to estimate the partitioning as a function of the temperature. Flow processes can be modeled isothermally or non-isothermally, and phase conditions represented may include a single (aqueous or CO2-rich) phase, as well as two-phase (brine-CO2) mixtures. Fluid phases may appear or disappear in the course of a simulation, and solid salt may precipitate or dissolve. Note that the model cannot be applied to subcritical conditions that involves both liquid and gaseous CO2 unless thermol process is ignored (i.e.,isothermal run). For those cases, a user may use the fluid property module ECO2M (Pruess, 2011) instead« less

SAPO-34 Membranes for N-2/CH4 separation: Preparation, characterization, separation performance and economic evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, SG; Zong, ZW; Zhou, SJ

2015-08-01

SAPO-34 membranes were synthesized by several routes towards N-2/CH4 separation. Membrane synthesis parameters including water content in the gel, crystallization time, support pore size, and aluminum source were investigated. High performance N-2-selective membranes were obtained on 100-nm-pore alumina tubes by using Al(i-C3H7O)(3) as aluminum source with a crystallization time of 6 h. These membranes separated N-2 from CH, with N-2 permeance as high as 500 GPU with separation selectivity of 8 at 24 degrees C. for a 50/50 N-2/CH4 mixture. Nitrogen and CH, adsorption isotherms were measured on SAPO-34 crystals. The N-2 and CH, heats of adsorption were 11 andmore » 15 kJ/mol, respectively, which lead to a preferential adsorption of CE-H-4 over N-2 in the N-2/CH4 mixture. Despite this, the SAPO-34 membranes were selective for N-2 over CH4 in the mixture because N-2 diffuses much faster than CH4 and differences in diffusivity played a more critical role than the competitive adsorption. Preliminary economic evaluation indicates that the required N-2/CH4 selectivity would be 15 in order to maintain a CH4 loss below 10%. For small nitrogen-contaminated gas wells, our current SAPO-34 membranes have potential to compete with the benchmark technology cryogenic distillation for N-2 rejection. (C) 2015 Elsevier B.V. All rights reserved,« less

Supramolecular architectures in the salt trimethoprimium ferrocene-1-carboxylate and the cocrystal 4-amino-5-chloro-2,6-dimethylpyrimidine-ferrocene-1-carboxylic acid (1/1).

PubMed

Swinton Darious, Robert; Thomas Muthiah, Packianathan; Perdih, Franc

2017-09-01

In the salt trimethoprimium ferrocenecarboxylate [systematic name: 2,4-diamino-5-(3,4,5-trimethoxybenzyl)pyrimidin-1-ium ferrocene-1-carboxylate], (C 14 H 19 N 4 O 3 )[Fe(C 5 H 5 )(C 6 H 4 O 2 )], (I), of the antibacterial compound trimethoprim, the carboxylate group interacts with the protonated aminopyrimidine group of trimethoprim via two N-H...O hydrogen bonds, generating a robust R 2 2 (8) ring motif (heterosynthon). However, in the cocrystal 4-amino-5-chloro-2,6-dimethylpyrimidine-ferrocene-1-carboxylic acid (1/1), [Fe(C 5 H 5 )(C 6 H 5 O 2 )]·C 6 H 8 ClN 3 , (II), the carboxyl-aminopyrimidine interaction [R 2 2 (8) motif] is absent. The carboxyl group interacts with the pyrimidine ring via a single O-H...N hydrogen bond. The pyrimidine rings, however, form base pairs via a pair of N-H...N hydrogen bonds, generating an R 2 2 (8) supramolecular homosynthon. In salt (I), the unsubstituted cyclopentadienyl ring is disordered over two positions, with a refined site-occupation ratio of 0.573 (10):0.427 (10). In this study, the two five-membered cyclopentadienyl (Cp) rings of ferrocene are in a staggered conformation, as is evident from the C...Cg...Cg...C pseudo-torsion angles, which are in the range 36.13-37.53° for (I) and 22.58-23.46° for (II). Regarding the Cp ring of the minor component in salt (I), the geometry of the ferrocene ring is in an eclipsed conformation, as is evident from the C...Cg...Cg...C pseudo-torsion angles, which are in the range 79.26-80.94°. Both crystal structures are further stabilized by weak π-π interactions.

Shelf-life extension of refrigerated Mediterranean mullet (Mullus surmuletus) using modified atmosphere packaging.

PubMed

Pournis, Nikolaos; Papavergou, Aikaterini; Badeka, Anastasia; Kontominas, Michael G; Savvaidis, Ioannis N

2005-10-01

The present work evaluated the quality and freshness characteristics and the effect of modified atmosphere packaging (MAP) on the shelf-life extension of refrigerated Mediterranean mullet using microbiological, biochemical, and sensory analyses. Fresh open sea red mullet (Mullus surmuletus) were packaged in four different atmospheres: M1, 10%/20%/70% (O2/ CO2/N2); M2, 10%/40%/50% (O2/CO2/N2); M3, 10%/60%/30% (O2/CO2/N2); identical fish samples were packaged in air. All fish were kept under refrigeration (4 +/- 0.5 degrees C) for 14 days. Of the three gas atmospheres, the 10%/40%/50% (M2) and 10%/ 60%/30% (M3) gas mixtures were the most effective for inhibiting growth of aerobic microflora in mullet samples until day 10 of refrigerated storage. H2S-producing bacteria and pseudomonads were part of the mullet microflora and their growth was partly inhibited under MAP conditions. Between these two bacterial groups, H2S-producing bacteria (including Shewanella putrefaciens) were dominant toward the end of the storage period, regardless of the packaging conditions. Brochothrix thermosphacta and lactic acid bacteria were found to be members of the final microbial flora of MAP and air-packaged mullet, whereas the Enterobacteriaceae population was lower than other bacterial groups. Of the chemical freshness indices determined, thiobarbituric acid values were variable in mullet samples irrespective of packaging conditions indicative of no specific oxidative rancidity trend. Based on sensorial data and aerobic plate count, trimethylamine nitrogen and total volatile basic nitrogen limit values in the range of ca. 15 to 23 and 52 to 60 mg N/100 g of fish muscle were obtained, respectively, for mullet packaged under modified atmosphere and air. Sensory analyses (odor and taste attributes) showed that the limit of sensorial acceptability was reached after ca. 6 days for the samples packaged in air, 8 days for the M1 and M3 samples, and after 10 days for the M2 samples. Respective shelf-life extension for fresh whole mullet was ca. 2 days (M1 and M3 gas mixtures), and 4 days (M2 gas mixture).

A Trinuclear Ni(II) Enediolate Complex: Synthesis, Characterization, and O2 Reactivity

PubMed Central

Arif, Atta M.; Berreau, Lisa M.

2009-01-01

Using a new N4-donor chelate ligand having a mixture of hydrophobic phenyl and hydrogen bond donor appendages, a trinuclear Ni(II) complex of the doubly deprotonated form of 2-hydroxy-1,3-diphenylpropane-1,3-dione was isolated, characterized (X-ray crystallography, elemental analysis, UV-vis, 1H NMR, FTIR, magnetic moment measurement), and evaluated for O2 reactivity. This complex, [(6-NA-6-Ph2TPANi)2(μ-PhC(O)C(O)C(O)Ph)2Ni](ClO4)2 (4), has two terminal pseudo octahedral Ni(II) centers supported by the tetradentate chelate ligand, and a central square planar Ni(II) ion ligated by oxygen atoms of two bridging enediolate ligands. In CH3CN, 4 exhibits a deep orange/brown color and λmax = 463 nm (ε = 16,000 M-1cm-1). The room temperature magnetic moment of 4, determined by Evans method, is μeff = 5.3(2) μB. This is consistent with the presence of two non-interacting high-spin Ni(II) centers, a diamagnetic central Ni(II) ion, and an overall quintet ground state. Exposure of a CH3CN solution of 4 to O2 results in the rapid loss of the orange/brown color to give a green solution. The products identified from this reaction are [(κ3-6-NA-6-Ph2TPA)Ni(O2Ph)(H2O)]ClO4 (5), benzil (PhC(O)C(O)Ph), and CO. Identification of 5 was achieved via its independent synthesis and comparison of its 1H NMR and mass spectral features with those of the 6-NA-6-Ph2TPA-containing product generated upon reaction of 4 with O2. The independently prepared sample of 5 was characterized by X-ray crystallography, elemental analysis, UV-vis, mass spectrometry, and FTIR. The O2 reactivity of 4 has relevance to the active site chemistry of Ni(II)-containing acireductone dioxygenase (Ni(II)-ARD). PMID:18959363

Synthesis, crystal structures and luminescence properties of new multi-component co-crystals of isostructural Co(II) and Zn(II) complexes

NASA Astrophysics Data System (ADS)

Tella, Adedibu C.; Owalude, Samson O.; Omotoso, Mary F.; Olatunji, Sunday J.; Ogunlaja, Adeniyi S.; Alimi, Lukman O.; Popoola, Olugbenga K.; Bourne, Susan A.

2018-04-01

Two novel isostructural compounds containing multi-component co-crystals [M(C6H4NO2)2(H2O)2](C9H6O6)2 (M = Co (1), Zn (2), C6H4NO2 = Picolinic acid, C9H6O6 = Trimesic acid) have been synthesized. The compounds were characterized by elemental analysis, FT-IR, UV-Visible and 1H NMR spectroscopies as well as thermal and single crystal X-ray diffraction analyses. Single crystal X-ray diffraction analysis reveals that 1 and 2 are isostructural. Compound 1 crystallizes in triclinic space group (P-1, with a = 5.154 (10) Å, b = 11.125 (2) Å, c = 14.113 (3) Å, α = 91.01 (3)°, β = 100.54 (3)°, and γ = 102.71 (3)°). In a similar fashion, compound 2 crystallizes in triclinic space group (P-1, with a = 5.1735 (3) Å, b = 11.0930 (10) Å, c = 14.1554 (8) Å, α = 91.70 (3)°, β = 100.26 (3)°, γ = 102.90 (3)°). The metal (II) cation presents distorted MN2O4 octahedral geometry with H2O molecules coordinated to the metal in equatorial position while the picolinic acid molecules are axially coordinated through the pyridine N atom. The two trimesic acid molecules are not part of the first coordination sphere. Compounds 1 and 2 constitute an example of a class of coordination compound of multicomponent crystals having trimesic acid outside the coordination sphere where it is neither protonated or deprotonated. The two compounds were investigated for luminiscence properties.

Electrodeposition mechanism of quaternary compounds Cu2ZnSnS4: Effect of the additives

NASA Astrophysics Data System (ADS)

Tang, Aiyue; Li, Zhilin; Wang, Feng; Dou, Meiling; Liu, Jingjun; Ji, Jing; Song, Ye

2018-01-01

The electrodeposition mechanism of pure phase Cu2ZnSnS4 (CZTS) thin film with subsequent annealing was investigated in detail. An electrolyte design principle of quaternary compounds was proposed. The complex ions of Cu(H2C6H5O7)+, Cu2(C6H5O7)+, Zn(C4H5O6)+, Sn(H2C6H5O7)+ and Sn2(C6H5O7)+, which influenced the reduction process and played important roles in co-deposition, were identified by UV spectra. Electrochemical studies indicated that trisodium citrate and tartaric acid could narrow the co-deposition potential range of the four elements to -0.8 V to -1.2 V (vs. SCE). The cause was the synergetic effect that trisodium citrate inhibited the reduction of Cu2+ and Sn2+ and tartaric acid promoted the reduction of Zn2+. The reduction of S2O32- was mainly attributed to the induction effect of the metallic ions, and the H+ dissociated from tartaric acid could also promote the cathode process of S2O32-. The reaction mechanism could be summarized as the following steps: (I) Cu(H2C6H5O7)+, Cu2(C6H5O7)+ → Cu, Sn(H2C6H5O7)+, Sn2(C6H5O7)+ → Sn, Zn(C4H5O6)+ → Zn; (II) the desorption of (H2C6H5O7)- and (C6H5O7)-, and the reduction of S2O32- induced by metallic ions and H+. The mechanism studies provided a path of electrolyte design for multicomponent compounds.

Hydrothermal synthesis of uranyl squarates and squarate-oxalates: hydrolysis trends and in situ oxalate formation.

PubMed

Rowland, Clare E; Cahill, Christopher L

2010-07-19

We report the synthesis of two uranyl squarates and two mixed-ligand uranyl squarate-oxalates from aqueous solutions under hydrothermal conditions. These products exhibit a range of uranyl building units from squarates with monomers in (UO(2))(2)(C(4)O(4))(5).6NH(4).4H(2)O (1; a = 16.731(17) A, b = 7.280(8) A, c = 15.872(16) A, beta = 113.294(16) degrees , monoclinic, P2(1)/c) and chains in (UO(2))(2)(OH)(2)(H(2)O)(2)(C(4)O(4)) (2; a = 12.909(5) A, b = 8.400(3) A, c = 10.322(4) A, beta = 100.056(7) degrees , monoclinic, C2/c) to two squarate-oxalate polymorphs with dimers in (UO(2))(2)(OH)(C(4)O(4))(C(2)O(4)).NH(4).H(2)O (3; a = 9.0601(7) A, b = 15.7299(12) A, c = 10.5108(8) A, beta = 106.394(1) degrees , monoclinic, P2(1)/n; and 4; a = 8.4469(6) A, b = 7.7589(5) A, c = 10.5257(7) A, beta = 105.696(1) degrees , monoclinic, P2(1)/m). The dominance at low pH of monomeric species and the increasing occurrence of oligomeric species with increasing pH suggests that uranyl hydrolysis, mUO(2)(2+) + nH(2)O right harpoon over left harpoon [(UO(2))(m)(OH)(n)](2m-n) + nH(+), has a significant role in the identity of the inorganic building unit. Additional factors that influence product assembly include in situ hydrolysis of squaric acid to oxalic acid, dynamic metal to ligand concentration, and additional binding modes resulting from the introduction of oxalate anions. These points and the effects of uranyl hydrolysis with changing pH are discussed in the context of the compounds presented herein.

The pristine nature of comets. [primeval composition of solar bodies

NASA Technical Reports Server (NTRS)

Delsemme, A. H.

1977-01-01

Abundance considerations suggest that comets are likely to be the most pristine minor bodies in the solar system. In proportion to solar abundances, the present scanty data suggest that cometary oxygen is not depleted, whereas carbon is by a factor of 4 and hydrogen, by a factor of 2000. This implies that comets are less depleted in H, C, N, O than CI chondrites, namely 10:1 in hydrogen, 4:1 in carbon and 3:1 in oxygen. These results have been obtained by using dust-to-gas ratios in comets to measure the relative abundance of silicon and metals to volatile material, and the spectra of atomic lines, mainly from the vacuum ultraviolet, to determine the H/O and C/O ratios of the mixture of volatile molecules.

Inverse Kinetic and Equilibrium Isotope Effects on Self-Assembly and Supramolecular Chirality of Porphyrin J-Aggregates.

PubMed

Zagami, Roberto; Romeo, Andrea; Castriciano, Maria A; Monsù Scolaro, Luigi

2017-01-01

When mixtures of D 2 O/DCl are used to foster the self-assembly formation of TPPS 4 porphyrin J-aggregates in aqueous solutions, an inverse kinetic isotope effect of 0.4 and an inverse equilibrium isotope effect of 0.6 are clearly detected. Most importantly, the addition of at least 10 % D 2 O causes an inversion in the handedness of the final chiral J-aggregates, thus evidencing an important role of deuterium in driving the enantiomeric excess in the scalemic mixture of such supramolecular assemblies. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural investigations of GaN grown by low-pressure chemical vapor deposition on 6H{endash}SiC and Al{sub 2}O{sub 3} from GaCl{sub 3} and NH{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koynov, S.; Topf, M.; Fischer, S.

1997-08-01

GaN films grown on (0001) 6H{endash}SiC and (0001) Al{sub 2}O{sub 3} substrates using low-pressure chemical vapor deposition with GaCl{sub 3} and NH{sub 3} as precursors are comparatively explored by optical, scanning tunneling, and transmission electron microscopy. Independent of the substrate material used, the surface of the GaN layers is covered by hexagonally shaped islands. For GaN on 6H{endash}SiC, the islands are larger in diameter ({approx}50 {mu}m) and rather uniformly distributed. An atomically flat interface is observed for GaN on Al{sub 2}O{sub 3} in contrast to GaN grown on 6H{endash}SiC, where the interface is characterized by large steps. For both substrates,more » faceted holes (named as pinholes) are observed in near-surface regions of the GaN layers occurring with a density of about 7{times}10{sup 8} cm{sup {minus}2}. No unequivocal correlation between the density of pinholes and the density of threading dislocations ({approx}1.6{times}10{sup 10} cm{sup {minus}2} for GaN/Al{sub 2}O{sub 3} and {approx}4{times}10{sup 9} cm{sup {minus}2} for GaN/6H{endash}SiC) can be found. Rather, different types of defects are identified to be correlated with the pinholes, implying a dislocation-independent mechanism for the pinhole formation. Despite the small lattice mismatch between GaN and 6H{endash}SiC, the pronounced original surface roughness of this substrate material is believed to account for both the marked interfacial roughness and the still existing high density of threading dislocations. {copyright} {ital 1997 American Institute of Physics.}« less

Crystal structure, electrical transport and phase transition in 2-methoxyanilinium hexachlorido stannate(IV) dehydrate

NASA Astrophysics Data System (ADS)

Karoui, Sahel; Chouaib, Hassen; Kamoun, Slaheddine

2017-04-01

A new organic-inorganic (C7H10NO)2[SnCl6]2H2O compound was synthesized and characterized by X-ray diffraction, thermal analysis, NMR spectroscopy and dielectric measurements. The crystal structure refinement shows that this compound crystallizes at 298 K in the monoclinic system (P21/a space group (Z = 2)). The structure was solved by Patterson method and refined to a final value of R = 0.034 for 2207 independent observed reflections. The cohesion and stability of the atomic arrangement result from the establishment of Nsbnd H⋯Cl, O(W)sbnd H(W)⋯Cl and Nsbnd H⋯O(W) hydrogen bonds between (C7H10NO)+ cations, isolated (SnCl6)2- anions and water molecules. This compound exhibits a phase transition at 305 K which was characterized by differential scanning calorimetry (DSC), X-rays powder diffraction and dielectric measurements. At high frequency, the electrical σTot.(ω,T) conductivity obey to the Jonscher's power law σTot.(ω,T) = σDC(T) + B(T) ωS(T). DC and AC conductivity in (C7H10NO)2[SnCl6]2H2O was investigated revealing that the phase transition from the monoclinic P21/a (phase I) to the monoclinic C2/c (phase II) which occurs at 305 K is characterized by a change of the mechanism of the electric transport: SPT in phase I and CBH in phase II.

Nanocomposites Derived from Carbon Nanofibers and a Hyperbranched Poly(Ether-Ketone): In Situ Polymerization, Chain-End Modification, and Properties (Preprint)

DTIC Science & Technology

2007-05-01

and Soxhlet - extracted with water for three days and methanol for three more days. It was then dried over P2O5 under reduced pressure at 120 °C...for 72 h to give the product in quantitative yield . Anal. Calcd. for C16.39H8O4: C, 73.22%; 6 H, 2.98%; O, 23.81%. Found: C, 72.94%; H, 3.12%; O...HBP-PEK)-g-VGCNF, 3e, to afford 0.47 (94% yield based on initial amount) of a black solid. Found: C, 98.66%; H, 0.93%; N, ɘ.20%; O, ɘ.10

Tuning the reactivity of Fe(V)(O) toward C-H bonds at room temperature: effect of water.

PubMed

Singh, Kundan K; Tiwari, Mrityunjay k; Ghosh, Munmun; Panda, Chakadola; Weitz, Andrew; Hendrich, Michael P; Dhar, Basab B; Vanka, Kumar; Sen Gupta, Sayam

2015-02-16

The presence of an Fe(V)(O) species has been postulated as the active intermediate for the oxidation of both C-H and C═C bonds in the Rieske dioxygenase family of enzymes. Understanding the reactivity of these high valent iron-oxo intermediates, especially in an aqueous medium, would provide a better understanding of these enzymatic reaction mechanisms. The formation of an Fe(V)(O) complex at room temperature in an aqueous CH3CN mixture that contains up to 90% water using NaOCl as the oxidant is reported here. The stability of Fe(V)(O) decreases with increasing water concentration. We show that the reactivity of Fe(V)(O) toward the oxidation of C-H bonds, such as those in toluene, can be tuned by varying the amount of water in the H2O/CH3CN mixture. Rate acceleration of up to 60 times is observed for the oxidation of toluene upon increasing the water concentration. The role of water in accelerating the rate of the reaction has been studied using kinetic measurements, isotope labeling experiments, and density functional theory (DFT) calculations. A kinetic isotope effect of ∼13 was observed for the oxidation of toluene and d8-toluene showing that C-H abstraction was involved in the rate-determining step. Activation parameters determined for toluene oxidation in H2O/CH3CN mixtures on the basis of Eyring plots for the rate constants show a gain in enthalpy with a concomitant loss in entropy. This points to the formation of a more-ordered transition state involving water molecules. To further understand the role of water, we performed a careful DFT study, concentrating mostly on the rate-determining hydrogen abstraction step. The DFT-optimized structure of the starting Fe(V)(O) and the transition state indicates that the rate enhancement is due to the transition state's favored stabilization over the reactant due to enhanced hydrogen bonding with water.

Evaporation Rates of Chemical Warfare Agents using 5 CM Wind Tunnels. 5. VX From Sand and Concrete

DTIC Science & Technology

2010-12-01

1 .9 ɝ > UJ Q 2 o o i II i E r tn r m v en *• A i- 8 3 3 as s« x1 c a> o c o O § > (%) Bumieuiou lueSy 8 i« r ^ JCi ...301 2.4 2.8 42 405 8.81 87.1 UKSand 93 194 2.0 2.1 42 405 39.82 92.1 UKSand 234 300 2.4 2.7 10 405 0.87 131 SS 18 58 1.3 1.4 10 18 0.95 83.2 SS 4...3c082 sand H 620 2.79 2.82 35.2 182 1.5 8.7 3c081 sand H 131 2.12 2.44 35.3 1SI 1.5 1.0 3c 154 sand H 580 2.76 2.69 35.3 181 1.5 6.1 3c093 sand H

NaF-assisted combustion synthesis of MoSi2 nanoparticles and their densification behavior

NASA Astrophysics Data System (ADS)

Nersisyan, Hayk H.; Lee, Tae Hyuk; Ri, Vladislav; Lee, Jong Hyeon; Suh, Hoyoung; Kim, Jin-Gyu; Son, Hyeon Taek; Kim, Yong-Ho

2017-03-01

The exothermic reduction of oxides mixture (MoO3+2SiO2) by magnesium in NaF melt enables the synthesis of nanocrystalline MoSi2 powders in near-quantitative yields. The combustion wave with temperature of about 1000-1200 °C was recorded in highly diluted by NaF starting mixtures. The by-products of combustion reaction (NaF and MgO) were subsequently removed by leaching with acid and washing with water. The as-prepared MoSi2 nanopowder composed of spherical and dendritic shape particles was consolidated using the spark plasma sintering method at 1200-1500 °C and 50 MPa for 10 min. The result was dense compacts (98.6% theoretical density) possessing submicron grains and exhibiting hardness of 8.74-12.92 GPa.

Inactivation of Escherichia coli O157:H7 attached to spinach harvester blade using bacteriophage.

PubMed

Patel, Jitendra; Sharma, Manan; Millner, Patricia; Calaway, Todd; Singh, Manpreet

2011-04-01

Outbreaks associated with leafy greens have focused attention on the transfer of human pathogens to these commodities during harvest with commercial equipment. Attachment of Escherichia coli O157:H7 on new or rusty spinach harvester blades immersed in spinach extract or 10% tryptic soy broth (TSB) was investigated. Bacteriophages specific for E. coli O157:H7 were evaluated to kill cells attached to blade. A cocktail of five nalidixic acid-resistant E. coli O157:H7 isolates was transferred to 25 mL of spinach extract or 10% TSB. A piece of sterilized spinach harvester blade (2×1") was placed in above spinach extract or 10% TSB and incubated at room (22 °C) or dynamic (30 °C day, 20 °C night) temperatures. E. coli O157:H7 populations attached to blade during incubation in spinach extract or 10% TSB were determined. When inoculated at 1 log CFU/mL, E. coli O157:H7 attachment to blades after 24 and 48 h incubation at dynamic temperature (6.09 and 6.37 log CFU/mL) was significantly higher than when incubated at 22 °C (4.84 and 5.68 log CFU/mL), respectively. After 48 h incubation, two blades were sprayed on each side with a cocktail of E. coli O157-specific bacteriophages before scraping the blade, and subsequent plating on Sorbitol MacConkey media-nalidixic acid. Application of bacteriophages reduced E. coli O157:H7 populations by 4.5 log CFU on blades after 2 h of phage treatment. Our study demonstrates that E. coli O157:H7 can attach to and proliferate on spinach harvester blades under static and dynamic temperature conditions, and bacteriophages are able to reduce E. coli O157:H7 populations adhered to blades. © Mary Ann Liebert, Inc.

Dynamics of glycerine and water transport across human skin from binary mixtures.

PubMed

Ventura, S A; Kasting, G B

2017-04-01

Skin transport properties of glycerine and water from binary mixtures contacting human skin were determined to better understand the mechanism of skin moisturization by aqueous glycerine formulations. Steady-state permeation for 3 H 2 O and 14 C-glycerine across split-thickness human skin in vitro and desorption dynamics of the same permeants in isolated human stratum corneum (HSC) were experimentally determined under near equilibrium conditions. These data were compared to a priori values developed in the context of a thermodynamic model for binary mixtures of glycerine and water and a previously determined water sorption isotherm for HSC. This allowed the estimation of diffusion and partition coefficients for each permeant in the HSC, as well as HSC thickness, as a function of composition of the contacting solution. These data may be used to estimate water retention and associated HSC swelling related to the absorption and slow release of glycerine from the skin. It took 6+ days for glycerine to completely desorb from HSC immersed in glycerine/water binary solutions. Desorption of both 3 H 2 O and 14 C-glycerine from HSC was slower in pure water than from binary mixtures, a result that is largely explained by the greater swelling of HSC in water. Parametric relationships were developed for water and glycerine intradiffusivities in HSC as functions of HSC water content, and a mutual diffusion coefficient was estimated by analogy with glycerine/water binary solutions. The intradiffusivity of 14 C-glycerine in HSC as inferred from sorption/desorption experiments was shown to be approximately 10-fold less than that inferred from permeation experiments, whereas the corresponding values for 3 H 2 O were comparable. These studies confirm that glycerine enters HSC in substantial quantities and has a long residence time therein. The coupling between bulk water and glycerine transport projected from binary solution data suggests the net effect of glycerine is to slow water loss from the skin. The data support the concept of glycerine as a humectant with an excellent balance of skin penetration and retention characteristics; however, they do not rule out the possibility of an additional biological effect on skin barrier homoeostasis. © 2016 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Tholins: Can They Provide a Substrate, Carbon and Nitrogen for Plant Production?

NASA Technical Reports Server (NTRS)

Wignarajah, Kanapathipillai; Khare, Bishun; Cruikshank, Dale; McKay, Christopher; Arnold, James O. (Technical Monitor)

1999-01-01

Tholin is a word coined to describe the entire class of complex organic solids produced in laboratory experiments where pre-biotic gaseous chemicals are subject to bombardment by high energy. The atomic composition of Titan tholin produced from 10 percent CH4 and 90 percent N2 in a simulation of Titan atmosphere irradiated by charged particles trapped in the magnetosphere of Saturn gave 67 percent C and 33 percent N. Hydrolysis of Titan tholin with 6N HCl produced a racemic mixture of biological and non-biological amino acids that was confirmed by GC/MS. Other tholins, that revealed the presence of amino acids, were UV tholin produced under possible primitive Earth conditions by irradiation of a mixture of gases (CH4, C2H6, NH3, H2S and liquid H2O) with long-wavelength ultraviolet light, representing the most abundant useful energy source for prebiological organic synthesis; Spark tholin in a crude simulation of Jupiter atmosphere using electrical discharge through a mixture of CH4, NH3, and H2O vapor. Pyrolytic GC/MS of Titan tholin produced more than one hundred organic compounds including saturated and unsaturated aliphatic hydrocarbons, substituted polycyclic aromatics, nitriles, amines, pyrroles, pyrazines, pyridines, pyrimidines, and the purine, adenine. Similar rich pyrolytic products were obtained with UV as well as Spark tholins. A range of two to four ring PAHs (Polycyclic Aromatic Hydrocarbons) in Spark as well as Titan tholins, some with one to four alkylation sites, were identified by two-step laser desorption/multiphoton ionization mass spectrometry and also confirmed by the synchronous fluorescence technique. Previous studies have demonstrated the potential for use of tholins as a source of carbon and energy by microbes. This paper describes studies that evaluate the potential for using different types of tholins as (a) a substrate for growing plants and (b) a source of carbon and nitrogen for plants. The data are interpreted in terms of the potential for using such tholins to grow plants for food in extraterrestrial habitats and also to speculate on the possibilities of abiotic evolution of plants.

New metal-organic frameworks of [M(C6H5O7)(C6H6O7)(C6H7O7)(H2O)] . H2O (M=La, Ce) and [Ce2(C2O4)(C6H6O7)2] . 4H2O

NASA Astrophysics Data System (ADS)

Weng, Sheng-Feng; Wang, Yun-Hsin; Lee, Chi-Shen

2012-04-01

Two novel materials, [M(C6H5O7)(C6H6O7)(C6H7O7)(H2O)] . H2O (M=La(1a), Ce(1b)) and [Ce2(C2O4)(C6H6O7)2] . 4H2O (2), with a metal-organic framework (MOF) were prepared with hydrothermal reactions and characterized with photoluminescence, magnetic susceptibility, thermogravimetric analysis and X-ray powder diffraction in situ. The crystal structures were determined by single-crystal X-ray diffraction. Compound 1 crystallized in triclinic space group P1¯ (No. 2); compound 2 crystallized in monoclinic space group P21/c (No. 14). The structure of 1 is built from a 1D MOF, composed of deprotonated citric ligands of three kinds. Compound 2 contains a 2D MOF structure consisting of citrate and oxalate ligands; the oxalate ligand arose from the decomposition in situ of citric acid in the presence of CuII ions. Photoluminescence spectra of compounds 1b and 2 revealed transitions between the 5d1 excited state and two levels of the 4f1 ground state (2F5/2 and 2F7/2). Compounds 1b and 2 containing CeIII ion exhibit a paramagnetic property with weak antiferromagnetic interactions between the two adjacent magnetic centers.

Investigation into the stabilization/solidification performance of Portland cement through cement clinker phases.

PubMed

Qiao, X C; Poon, C S; Cheeseman, C R

2007-01-10

This research studied the influence of individual heavy metal on the hydration reactions of major cement clinker phases in order to investigate the performance of cement based stabilization/solidification (S/S) system. Tricalcium silicate (C3S) and tricalcium aluminate (C3A) had been mixed with individual heavy metal hydroxide including Zn(OH)2, Pb(OH)2 and Cu(OH)2, respectively. The influences of these heavy metal hydroxides on the hydration of C3S and C3A have been characterized by X-ray diffraction (XRD) and differential scanning calorimetry-thermogravimetry (DSC-TG). A mixture of Zn(OH)2, Pb(OH)2 and Cu(OH)2 was blended with Portland cement (PC) and evaluated through compressive strength and dynamic leach test. XRD and DSC-TG data show that all the heavy metal hydroxides (Zn(OH)2, Pb(OH)2 and Cu(OH)2) have detrimental effects on the hydration of C3A, but only Zn(OH)2 does to the C3S at early curing ages which can completely inhibit the hydration of C3S due to the formation of CaO(Zn(OH)2).2H2O. Cu6Al2O8CO(3).12H2O, Pb2Al4O4(CO3)(4).7H2O and Zn6Al2O8CO(3).12H2O are formed in all the samples containing C3A in the presence of metal hydroxides. After adding CaSO4 into C3A, the detrimental effect of heavy metals increases due to the coating effect of both calcium aluminate sulphates and heavy metal aluminate carbonates. The influence of heavy metal hydroxide on the hydration of C3S and C3A can be used to predict the S/S performance of Portland cement.

Selective Sensing of Gas Mixture via a Temperature Modulation Approach: New Strategy for Potentiometric Gas Sensor Obtaining Satisfactory Discriminating Features

PubMed Central

Li, Fu-an; Jin, Han; Wang, Jinxia; Zou, Jie; Jian, Jiawen

2017-01-01

A new strategy to discriminate four types of hazardous gases is proposed in this research. Through modulating the operating temperature and the processing response signal with a pattern recognition algorithm, a gas sensor consisting of a single sensing electrode, i.e., ZnO/In2O3 composite, is designed to differentiate NO2, NH3, C3H6, CO within the level of 50–400 ppm. Results indicate that with adding 15 wt.% ZnO to In2O3, the sensor fabricated at 900 °C shows optimal sensing characteristics in detecting all the studied gases. Moreover, with the aid of the principle component analysis (PCA) algorithm, the sensor operating in the temperature modulation mode demonstrates acceptable discrimination features. The satisfactory discrimination features disclose the future that it is possible to differentiate gas mixture efficiently through operating a single electrode sensor at temperature modulation mode. PMID:28287492

Tensile Stress Rupture Behavior of a Woven Ceramic Matrix Composite in Humid Environments at Intermediate Temperature — Part I

NASA Astrophysics Data System (ADS)

Larochelle, K. J.; Morscher, G. N.

2006-05-01

The stress rupture strength of the SYL-iBN/BN/SiC composite was evaluated at 550 and 750 °C with moisture content levels of 0.0, 0.2, and 0.6 atm partial pressure of water vapor, pH2O. The stress rupture strengths decreased with respect to time with the rate of decrease related to the temperature and the amount of moisture content. In all cases the degradation was more severe initially and then approached a run-out threshold level. The thresholds were reached at approximately 100+, 60, 80 h for the 550 °C with 0.0, 0.2, and 0.6 pH2O, respectively. The thresholds were reached at approximately 40, 20, and 10 h for the 750 °C cases. The interpolated stress rupture strengths at 100 h for 0.0, 0.2, and 0.6 pH2O at 550 °C were 82%, 68%, and 51% of the room temperature monotonic tensile strength. At 750 °C these strengths were 67%, 51%, and 50%. Analysis of Field Emission Scanning Electron Microscopy images showed evidence of embrittlement of the fiber/matrix interphase. Little to no embrittlement was observed at both temperatures with 0.0 pH2O. At both 550 and 750 °C with 0.2 and 0.6 pH2O, evidence of embrittlement increased with temperature and test duration with the most extensive embrittlement observed at 750 °C with 0.6 pH2O.

Nqrs Data for H6I3InO12 [I3InO9·3(H2O)] (Subst. No. 2289)

NASA Astrophysics Data System (ADS)

Chihara, H.; Nakamura, N.

This document is part of Subvolume B 'Substances Containing C10H16 … Zn' of Volume 48 'Nuclear Quadrupole Resonance Spectroscopy Data' of Landolt-Börnstein - Group III 'Condensed Matter'. It contains an extract of Section '3.2 Data tables' of the Chapter '3 Nuclear quadrupole resonance data' providing the NQRS data for H6I3InO12 [I3InO9·3(H2O)] (Subst. No. 2289)

Crystal structure of 1-methyl-3-([2,2-dimethyl-4,6-dioxo-1,3-dioxane-5-ylidene]methyl)urea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habibi, A., E-mail: habibi@khu.ac.ir; Ghorbani, H. S.; Bruno, G.

2013-12-15

The crystal structure of 1-Methyl-3-([2,2-dimethyl-4,6-dioxo-1,3-dioxane-5-ylidene]methyl)urea (C{sub 9}H{sub 12}N{sub 2}O{sub 5}) has been determined by single crystal X-ray diffraction analysis. The crystals are monoclinic, a = 5.3179(2), b = 18.6394(6), c =10.8124(3) Å, β = 100.015(2)°, Z = 4, sp. gr. P2{sub 1}/c, R = 0.0381 for 2537 reflections with I > 2σ(I). Except for C(CH{sub 3}){sub 2} group, the molecule is planar. The structure is stabilized by inter- and intramolecular N-H...O hydrogen bonds and weak C-H...O interactions.

Optimization of o-phtaldialdehyde/2-mercaptoethanol postcolumn reaction for the hydrophilic interaction liquid chromatography determination of memantine utilizing a silica hydride stationary phase.

PubMed

Douša, Michal; Pivoňková, Veronika; Sýkora, David

2016-08-01

A rapid procedure for the determination of memantine based on hydrophilic interaction chromatography with fluorescence detection was developed. Fluorescence detection after postcolumn derivatization with o-phtaldialdehyde/2-mercaptoethanol was performed at excitation and emission wavelengths of 345 and 450 nm, respectively. The postcolumn reaction conditions such as reaction temperature, derivatization reagent flow rate, and reagents concentration were studied due to steric hindrance of amino group of memantine. The derivatization reaction was applied for the hydrophilic interaction liquid chromatography method which was based on Cogent Silica-C stationary phase with a mobile phase consisting of a mixture of 10 mmol/L citric acid and 10 mmol/L o-phosphoric acid (pH 6.0) with acetonitrile using an isocratic composition of 2:8 v/v. The benefit of the reported approach consists in a simple sample pretreatment and a quick and sensitive hydrophilic interaction chromatography method. The developed method was validated in terms of linearity, accuracy, precision, and selectivity according to the International Conference on Harmonisation guidelines. The developed method was successfully applied for the analysis of commercial memantine tablets. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

21 CFR 176.300 - Slimicides.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) cyclohexanone 1,2-Bis(monobromoacetoxy) ethane [CA Reg. No. 3785-34-0] At a maximum level of 0.10 pound per ton... Methylenebisbutanethiolsulfonate Methylenebisthiocyanate 2-Nitrobutyl bromoacetate [CA Reg. No. 32815-96-6] At a maximum level of 0...)phosphonium sulfate (CAS Reg. No. 55566-30-8) Maximum use level of 84 mg/kg in the pulp slurry. The additive...

21 CFR 176.300 - Slimicides.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) cyclohexanone 1,2-Bis(monobromoacetoxy) ethane [CA Reg. No. 3785-34-0] At a maximum level of 0.10 pound per ton... Methylenebisbutanethiolsulfonate Methylenebisthiocyanate 2-Nitrobutyl bromoacetate [CA Reg. No. 32815-96-6] At a maximum level of 0...)phosphonium sulfate (CAS Reg. No. 55566-30-8) Maximum use level of 84 mg/kg in the pulp slurry. The additive...

TOLERANCE TO AMINO ACID MIXTURES AND CASEIN DIGESTS GIVEN INTRAVENOUSLY

PubMed Central

Madden, S. C.; Woods, R. R.; Shull, F. W.; Remington, J. H.; Whipple, G. H.

1945-01-01

Several synthetic mixtures of natural and racemic crystalline amino acids suitable for the daily nitrogen requirement are tested in dogs for their tolerance upon intravenous injection. Certain mixtures of the ten essential amino acids plus non-essential amino acids exclusive of glutamic acid are accepted without any obvious sign of disturbance even at rates above 10 mg. nitrogen per kilo per minute for quantities greater than 300 mg. per kilo. One such mixture consists in parts per 100 of dl-threonine 7, dl-valine 15, l(-)-leucine 10.9, dl-isoleucine 9.9, l(+)-lysine· HCl·H2O 10.9, dl-tryptophane 3, dl-phenylalanine 9.9, dl-methionine 6, l(+)-histidine·HCl·H2O 5, l(+)-arginine-HCl 5, glycine 9.9, dl-α-alanine 4, dl-serine 2, l(-)-cystine 0.5, and l(-)-tyrosine 1. In addition other well tolerated mixtures included the prolines. When glutamic acid, natural or racemic, is included in similar mixtures vomiting reactions frequently occur at nitrogen rates above 4 mg. per kilo per minute. Vomiting almost always occurs on the first daily injection containing glutamic acid and usually on any subsequent injection containing more than 100 mg. glutamic acid per kilo unless given very slowly. Upon the addition of glycine certain mixtures of the ten essential amino acids show an improved tolerance. Two casein digests tested usually produced vomiting at injection rates above 2 mg. nitrogen per kilo per minute, probably because of their glutamic acid content. No serious reaction has ever occurrred to any mixture of amino acids or casein digest tested. Elimination of minor reactions such as vomiting appears possible and desirable for greater usefulness of these solutions in parenteral feeding. PMID:19871468

Multi-species detection using multi-mode absorption spectroscopy (MUMAS)

NASA Astrophysics Data System (ADS)

Northern, J. H.; Thompson, A. W. J.; Hamilton, M. L.; Ewart, P.

2013-06-01

The detection of multiple species using a single laser and single detector employing multi-mode absorption spectroscopy (MUMAS) is reported. An in-house constructed, diode-pumped, Er:Yb:glass micro-laser operating at 1,565 nm with 10 modes separated by 18 GHz was used to record MUMAS signals in a gas mixture containing C2H2, N2O and CO. The components of the mixture were detected simultaneously by identifying multiple transitions in each of the species. By using temperature- and pressure-dependent modelled spectral fits to the data, partial pressures of each species in the mixture were determined with an uncertainty of ±2 %.

Decomposition of toluene in a steady-state atmospheric-pressure glow discharge

NASA Astrophysics Data System (ADS)

Trushkin, A. N.; Grushin, M. E.; Kochetov, I. V.; Trushkin, N. I.; Akishev, Yu. S.

2013-02-01

Results are presented from experimental studies of decomposition of toluene (C6H5CH3) in a polluted air flow by means of a steady-state atmospheric pressure glow discharge at different water vapor contents in the working gas. The experimental results on the degree of C6H5CH3 removal are compared with the results of computer simulations conducted in the framework of the developed kinetic model of plasma chemical decomposition of toluene in the N2: O2: H2O gas mixture. A substantial influence of the gas flow humidity on toluene decomposition in the atmospheric pressure glow discharge is demonstrated. The main mechanisms of the influence of humidity on C6H5CH3 decomposition are determined. The existence of two stages in the process of toluene removal, which differ in their duration and the intensity of plasma chemical decomposition of C6H5CH3 is established. Based on the results of computer simulations, the composition of the products of plasma chemical reactions at the output of the reactor is analyzed as a function of the specific energy deposition and gas flow humidity. The existence of a catalytic cycle in which hydroxyl radical OH acts a catalyst and which substantially accelerates the recombination of oxygen atoms and suppression of ozone generation when the plasma-forming gas contains water vapor is established.

Phase stable rare earth garnets

DOEpatents

Kuntz, Joshua D.; Cherepy, Nerine J.; Roberts, Jeffery J.; Payne, Stephen A.

2013-06-11

A transparent ceramic according to one embodiment includes a rare earth garnet comprising A.sub.hB.sub.iC.sub.jO.sub.12, where h is 3.+-.10%, i is 2.+-.10%, and j is 3.+-.10%. A includes a rare earth element or a mixture of rare earth elements, B includes at least one of aluminum, gallium and scandium, and C includes at least one of aluminum, gallium and scandium, where A is at a dodecahedral site of the garnet, B is at an octahedral site of the garnet, and C is at a tetrahedral site of the garnet. In one embodiment, the rare earth garment has scintillation properties. A radiation detector in one embodiment includes a transparent ceramic as described above and a photo detector optically coupled to the rare earth garnet.

Synthesisofc-lifepo4 composite by solid state reaction method

NASA Astrophysics Data System (ADS)

Rahayu, I.; Hidayat, S.; Noviyanti, A. R.; Rakhmawaty, D.; Ernawati, E.

2017-02-01

In this research, the enhancement of LiFePO4 conductivity was conducted by doping method with carbon materials. Carbon-based materials were obtained from the mixture of sucrose, and the precursor of LiH2PO4 and α-Fe2O3 was synthesized by solid state reaction. Sintering temperature was varied at 700°C, 800°C, 900°C and 1,000°C. The result showed that C-LiFePO4 could be synthesized by using solid state reaction method. Based on the XRD and FTIR spectrums, C-LiFePO4 can be identified as the type of crystal, characterized by the appearance of sharp signal on (011), (211) and typical peak of LiFePO4 materials. The result of conductivity measurement from C-LiFePO4 at sintering temperature of 900°C and 1,000°C was 2×10-4 S/cm and 4×10-4S/cm, respectively. The conductivity value at sintering temperature of 700°C and 800°C was very small (<10-6 S/cm), which cannot be measured by the existing equipment.

Hydrogen bonding in goldichite, KFe(SO4)2ṡ4H2O: structure refinement

NASA Astrophysics Data System (ADS)

Yang, Zhuming; Giester, Gerald

2018-02-01

The crystal structure of goldichite KFe(SO4)2ṡ4H2O was determined on a single crystal from the Baiyinchang copper deposit, Gansu, China. [ P121/ c1, a = 10.395(2), b = 10.475(2), c = 9.0875(18) Å, β = 101.65(3)°, V = 969.1(3) Å3, Z = 4]. All non-H atoms were refined with anisotropic displacement parameters and positions of H-atoms were determined by difference Fourier methods and refined from X-ray diffraction data. The crystal structure of goldichite consists of corrugated sheets parallel to the (100) plane by sharing corners between FeO6 octahedra and SO4 tetrahedra. The interstitial potassium atom exhibits a [KO7(H2O)2] nine-fold coordination, which shares edges to form a column parallel to the c-axis and to build a slab with the corrugated sheet. These slabs are linked in the [100] direction through a network of hydrogen bonds. Three types of hydrogen bonds involve links of slabs: Ow(3)-H(3B)···O(1), Ow(6)-H(6B)···O(11) and Ow(9)-H(9B)···O(11). The FTIR spectrum of goldichite shows a strong absorption between 3384 cm-1 and 3592 cm-1, which is in accordance with the O-H···O distances derived from structure data.

HILIC separation and quantitation of water-soluble vitamins using diol column.

PubMed

Karatapanis, Andreas E; Fiamegos, Yiannis C; Stalikas, Constantine D

2009-04-01

Hydrophilic interaction liquid-chromatography (HILIC) in conjunction with diode array detection has been applied for the separation of selected-water-soluble vitamins using an end-capped HILIC-diol column. Vitamins with significant biological importance, such as thiamine (B(1)), riboflavin (B(2)), nicotinic acid (B(3)), nicotinamide (B(3)), pyridoxine (B(6)), folic acid (B(9)), cyanocobalamin (B(12)) and ascorbic acid (vitamin C) were simultaneously separated. Chromatographic conditions including type and percentage of organic modifier in the mobile phase, pH, type and concentration of buffer salt and flow rate were investigated. ACN was shown to offer superior separation for the compounds tested as compared to methanol, isopropanol and THF. Isocratic separation and analysis were achieved for six vitamins (B(1), B(2), nicotinic acid/nicotinamide, B(6) and C) at ACN-H(2)O 90:10, containing ammonium acetate 10 mM, triethylamine 20 mM, pH 5.0, using a flow rate of 0.8 mL/min, while a gradient was necessary to resolve a mixture of all eight water-soluble vitamins. The HILIC method was validated and successfully applied to the analysis of a pharmaceutical formulation and an energy drink negating the need for time consuming clean-up steps.

A novel, fast responding, low noise potentiometric sensor containing a carbon-based polymeric membrane for measuring surfactants in industrial and environmental applications.

PubMed

Samardžić, Mirela; Galović, Olivera; Hajduković, Mateja; Sak-Bosnar, Milan

2017-01-01

A new high-sensitivity potentiometric sensor for anionic surfactants was fabricated using the dimethyldioctadecylammonium-tetraphenylborate (DDA-TPB) ion associate as an ionophore that was incorporated into a liquid PVC membrane. Carbon powder was used for immobilization of the ionophore in the membrane, thus significantly reducing its ohmic resistance and reducing its signal drift. The sensor exhibits a sub-Nernstian response for both dodecylbenzenesulfonate (DBS) and dodecyl sulfate (DS) in H 2 O (55.3 and 58.5mV/decade of activity, respectively) in a range between 3.2×10 -7 and 4.6×10 -3 M for DS and 2.5×10 -7 and 1.2×10 -3 M for DBS. The sensor also exhibited a sub-Nernstian response for DS and DBS in 10mM Na 2 SO 4 (55.4 and 57.7mV/decade of activity, respectively) between 2.5×10 -7 and 4.6×10 -3 M for DS and 1.5×10 -7 and 8.8×10 -4 M for DBS. The detection limits for DS and DBS in H 2 O were 2.5×10 -7 and 2.0×10 -7 M and in 10mM Na 2 SO 4 the detection limits were 2.5×10 -7 and 1.2×10 -7 M, respectively. The response time of the sensor was less than 5s for changes at higher concentration levels (above 1×10 -4 M) in both water and 10mM Na 2 SO 4. At lower concentrations (below 1×10 -5 M) the response times were 8 and 6s in water and 10mM Na 2 SO 4 , respectively. The signal drift of the sensor was 1.2mV/hour. The new carbon-based sensor exhibited excellent selectivity performance for DS over almost all of the anions commonly present in commercial formulations and it was successfully employed as an end-point detector in potentiometric titrations of anionic surfactants in a pH range from 3 to 12. Three-component mixtures containing sodium alkanesulfonate (C 10 , C 12 and C 14 ) were successfully differentially titrated. Copyright © 2016 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rivenet, Murielle; Vigier, Nicolas; Roussel, Pascal

Six new layered uranyl vanadates (NH{sub 4}){sub 2}[(UO{sub 2}){sub 2}V{sub 2}O{sub 8}] (1), (H{sub 2}EN)[(UO{sub 2}){sub 2}V{sub 2}O{sub 8}] (2), (H{sub 2}DAP)[(UO{sub 2}){sub 2}V{sub 2}O{sub 8}] (3), (H{sub 2}PIP)[(UO{sub 2}){sub 2}(VO{sub 4}){sub 2}].0,8H{sub 2}O (4), (H{sub 2}DMPIP)[(UO{sub 2}){sub 2}V{sub 2}O{sub 8}] (5), (H{sub 2}DABCO)[(UO{sub 2}){sub 2}(VO{sub 4}){sub 2}] (6) were prepared from mild-hydrothermal reactions using 1,2-ethylenediamine (EN); 1,3-diaminopropane (DAP); piperazine (PIP); 1-methylpiperazine (MPIP); 1,4-diazabicyclo[2,2,2]octane (DABCO). The structures of 1, 4, 5 and 6 were solved using single-crystal X-ray diffraction data while the structural models of 2 and 3 were established from powder X-ray diffraction data. In compounds 1, 2, 3more » and 5, the uranyl-vanadate layers are built from dimers of edge-shared UO{sub 7} pentagonal bipyramids and dimers of edge-shared VO{sub 5} square pyramids further connected through edge-sharing. In 1 and 3, the layers are identical to that occurring in the carnotite group of uranyl-vanadates. In 2 and 5, the V{sub 2}O{sub 8} dimers differ in orientation leading to a new type of layer. The layers of compound 4 and 6 are built from chains of edge-shared UO{sub 7} pentagonal bipyramids connected by VO{sub 4} tetrahedra and are of uranophane-type anion topology. For the six compounds, the ammonium or organoammonium cation resides in the space between the inorganic layers. Crystallographic data: 1 monoclinic, space group P2{sub 1}/c with a=6.894(2), b=8.384(3), c=10.473(4) A and {beta}=106.066(5){sup o}, 2 monoclinic, space group P2{sub 1}/a with a=13.9816(6), b=8.6165(3), c=10.4237(3) A and {gamma}=93.125(3){sup o}, 3 orthorhombic, space group Pmcn with a=14.7363(8), b=8.6379(4) and c=10.4385(4) A, 4 monoclinic, space group C2/m with a=15.619(2), b=7.1802(8), c=6.9157(8) A and {beta}=101.500(2){sup o}, 5 monoclinic, space group P2{sub 1}/b with a=9.315(2), b=8.617(2), c=10.5246(2) A and {gamma}=114.776(2){sup o}, 6 monoclinic, space group C2/m with a=17.440(2), b=7.1904(9), c=6.8990(8) A and {beta}=98.196(2){sup o}. - Graphical abstract: The three types of layer in layered uranyl-vanadates using diamine as a structure-directing agent.« less

Rotational level-dependent collisional broadening and line shift of the A2Sigma(+)-X2Pi (1,0) band of OH in hydrogen-air combustion gases

NASA Technical Reports Server (NTRS)

Kessler, W. J.; Allen, M. G.; Davis, S. J.

1993-01-01

Measurements of the collisional broadening and line shift of the (1,0) band of the A2Sigma(+)-X2Pi system of OH are reported in atmospheric pressure hydrogen-air combustion gases. The measurements were made using a single-mode, narrow linewidth, frequency-doubled ring dye laser operating near 283 nm. The OH was generated in the combustion gases of a flat flame H2-air burner. Collisional broadening parameters for equilibrium mixtures of H2, O2, H2O, and N2 were obtained spanning a range of fuel/air equivalence ratios from 0.6 to 1.6 and temperatures from 1500 to 2050 K. Measurements were obtained spanning rotational quantum numbers from 4.5 to 16.5. The collision induced frequency shift was determined to be 0.1 that of the collisional broadening.

Synthesis and crystal structures of inclusion compounds of 2,2'-dithiosalicylic acid and triethylamine/tripropylamine

NASA Astrophysics Data System (ADS)

Yang, Y. X.; Li, H. Y.; Wu, J. F.

2015-12-01

Herein we reported two new inclusion compounds of 2,2'-dithiosalicylic acid (C14H10O4S2, DTSA) and triethylamine and tripropylamine, [C14H8O4S 2 2- · [N+(C2H5)3]2 · H2O] (1) and [C14H10O4S2 · C14H8O4S 2 2- · [N+(C3H7)3]2] (2). Compound 1: triclinic P overline 1, a = 8.2159(2), b = 12.5724(3), c = 14.9203(3) Å, α = 97.0390(10), β = 101.4310(10)°, γ = 101.3370(10)°, V = 1460.06(6) Å3, Z = 2, R 1 = 0.0526, wR 2 = 0.1495; Compound 2: monoclinic P21/ c, a = 20.5178(13), b = 15.3623(8), c = 15.5529(9) Å, β = 102.036(3)°, V = 4794.5(5) Å3, Z = 4, R 1 = 0.0533, wR 2 = 0.1252. In these two crystal structures, DTSA utilizes conventional O-H···O hydrogen bonds to link to generate varied host lattices, in which the central N atoms of the guest amine molecules accept the protons of DTSA to form the corresponding cations to act as the couterions to develop the stable crystal structures. Noticeably, except Van der Waals forces usually existing between the host and guest molecules, the central N atoms of the guests of the two compounds can construct strong N-H…O hydrogen bonds with the related host molecules, which further enforce the host-guest interactions to help form the final inclusion compounds.

Synthesis, spectroscopic investigations (X-ray, NMR and TD-DFT), antimicrobial activity and molecular docking of 2,6-bis(hydroxy(phenyl)methyl)cyclohexanone.

PubMed

Barakat, Assem; Ghabbour, Hazem A; Al-Majid, Abdullah Mohammed; Soliman, Saied M; Ali, M; Mabkhot, Yahia Nasser; Shaik, Mohammed Rafi; Fun, Hoong-Kun

2015-07-21

The synthesis of 2,6-bis(hydroxy(phenyl)methyl)cyclohexanone 1 is described. The molecular structure of the title compound 1 was confirmed by NMR, FT-IR, MS, CHN microanalysis, and X-ray crystallography. The molecular structure was also investigated by a set of computational studies and found to be in good agreement with the experimental data obtained from the various spectrophotometric techniques. The antimicrobial activity and molecular docking of the synthesized compound was investigated.

Acid and alcohol tolerance of Escherichia coli O157:H7 in pulque, a typical Mexican beverage.

PubMed

Gómez-Aldapa, Carlos A; Díaz-Cruz, Claudio A; Villarruel-López, Angelica; Del Refugio Torres-Vitela, M; Rangel-Vargas, Esmeralda; Castro-Rosas, Javier

2012-03-01

Pulque is a traditional Mexican fermented alcoholic beverage produced from the nectar of maguey agave plants. No data exist on the behavior of Escherichia coli O157:H7 in agave nectar and pulque. An initial trial was done of the behavior of E. coli O157:H7 during fermentation of nectar from a single producer, a nectar mixture from different producers and "seed" pulque. A second trial simulating artisanal pulque production was done by contaminating fresh nectar with a cocktail of three E. coli O157:H7 strains, storing at 16 ° and 22 °C for 14 h, adding seed pulque and fermenting until pulque was formed. A third trial used pulque from the second trial stored at 22 °C as seed to ferment fresh nectar at 22 °C for 48 h (fermentation cycle). This procedure was repeated for an additional two fermentation cycles. During incubation at 16 ° or 22 °C in the first trial, the E. coli O157:H7 strains multiplied in both the single producer nectar and nectar mixture, reaching maximum concentration at 12h. E. coli O157:H7 cell concentration then decreased slowly, although it survived at least 72 h in both fermented nectars. E. coli O157:H7 did not multiply in the seed pulque but did survive at least 72 h. In the second trial, the numbers of E. coli O157:H7 increased approximately 1.5 log CFU/ml at 22 °C and 1.2 log CFU/ml at 16 °C after 14 h. After seed pulque was added, E. coli O157:H7 concentration decreased to approximately 2 log CFU/ml, and then remained constant until pulque was produced. In the third trial, the E. coli O157:H7 cells multiplied and survived during at least three nectar fermentation cycles. The results suggest that E. coli O157:H7 can develop acid and alcohol tolerance in pulque, and constitutes a public health risk for pulque consumers. Copyright © 2011 Elsevier B.V. All rights reserved.

Thermodynamic and NMR Studies of Solvent Effect on Enantiomeric Recognition for a Chiral Organiz Ammonium Cation by Chiral Diketopyridino-18- Crown-6 Type Ligands at 25.0 deg C.

DTIC Science & Technology

1994-05-11

analyses, 1H NM&, and JR specPit oscopy. The purities were also determined quantitatively by a thermometric titration technique. 19 By titrting...enantiomers of NapEt with 18- crown-6 (SIGMA Chemical Company, its purity was 99.5% as determined by therm--ometric titration agtains a standard NaBr...isoperibol titration calorimetry at 25.0 - 0.1oC in CACi6CHOH solvent mixtures. The initial solution volume in the dewar was 20 mL Tne calorimeter (wac

Study of collisional deactivation of O{sub 2}(b{sup 1}{Sigma}{sub g}{sup +}) molecules in a hydrogen-oxygen mixture at high temperatures using laser-induced gratings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kozlov, D. N., E-mail: dnk@kapella.gpi.ru; Kobtsev, V. D.; Stel'makh, O. M.

2013-07-15

Collisional deactivation of O{sub 2}(b{sup 1}{Sigma}{sub g}{sup +}) molecules resonantly excited by a 10 ns pulse of laser radiation with a wavelength of 762 nm in H{sub 2}/O{sub 2} mixtures is experimentally studied. The radiation intensity and hence the molecule excitation efficiency have a spatially periodic modulation that leads to the formation of laser-induced gratings (LIGs) of the refractive index. The study of LIG temporal evolution allows collisional relaxation rates of molecular excited states and gas temperature to be determined. In this work, the b{sup 1}{Sigma}{sub g}{sup +} state of O{sub 2} molecules deactivation rates are measured in a 4.3more » vol % H{sub 2} mixture at the number density of 2 amg in the temperature range 291-850 K. The physical deactivation is shown to dominate in the collisions of H{sub 2} with O{sub 2}(b{sup 1}{Sigma}{sub g}{sup +}) and O{sub 2}(a{sup 1}{Delta}{sub g}) up to temperatures of 780-790 K at time delays up to 10 {mu}s after the excitation pulse. The parameters of the obtained temperature dependence of the (b{sup 1}{Sigma}{sub g}{sup +} state deactivation rate agree well with the data of independent measurements performed earlier at lower temperatures (200-400 K). Tunable diode laser absorption spectroscopy is used to measure the temperature dependence of the number density of the H{sub 2}O molecules which appear as the mixture, as the result of the dark gross reaction with O{sub 2} molecules in the ground state, O{sub 2} + 2H{sub 2} {yields} 2H{sub 2}O. The measurements show that this reaction results in complete transformation of H{sub 2} into H{sub 2}O at temperatures of 790-810 K.« less

21 CFR 184.1061 - Lactic acid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Lactic acid. 184.1061 Section 184.1061 Food and... Substances Affirmed as GRAS § 184.1061 Lactic acid. (a) Lactic acid (C3H6O3, CAS Reg. Nos.: dl mixture, 598-82-3; l-isomer, 79-33-4; d-isomer, 10326-41-7), the chemical 2-hydroxypropanoic acid, occurs...

21 CFR 184.1061 - Lactic acid.

Code of Federal Regulations, 2014 CFR

2014-04-01

....1061 Lactic acid. (a) Lactic acid (C3H6O3, CAS Reg. Nos.: dl mixture, 598-82-3; l-isomer, 79-33-4; d... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Lactic acid. 184.1061 Section 184.1061 Food and... hydrolysis to lactic acid. (b) The ingredient meets the specifications of the Food Chemicals Codex, 3d Ed...

21 CFR 184.1061 - Lactic acid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Lactic acid. 184.1061 Section 184.1061 Food and... Substances Affirmed as GRAS § 184.1061 Lactic acid. (a) Lactic acid (C3H6O3, CAS Reg. Nos.: dl mixture, 598-82-3; l-isomer, 79-33-4; d-isomer, 10326-41-7), the chemical 2-hydroxypropanoic acid, occurs...

Assembly of a new inorganic-organic frameworks based on [Sb4Mo12(OH)6O48]10- polyanion

NASA Astrophysics Data System (ADS)

Thabet, Safa; Ayed, Meriem; Ayed, Brahim; Haddad, Amor

2014-10-01

A new organic-inorganic hybrid material, (C4N2H7)8[K(H2O)]2[Sb4Mo12(OH)6O48]ṡ16H2O (1) has been isolated by the conventional solution method and characterized by elemental analysis, single-crystal X-ray diffraction, infrared spectroscopy, UV-visible spectroscopies, cyclic voltammetry and TG-DTA analysis. The compound crystallizes in the triclinic space group P - 1 with a = 13.407(6) Å, b = 13.906(2) Å, c = 14.657(7) Å, α = 77.216(9)°, β = 71.284(6)°, γ = 71.312(3)° and Z = 1. The crystal structure exhibits an infinite 1D inorganic structure built from [Sb4Mo12(OH)6O48]10- clusters and potassium cations; adjacent chains are further joined up hydrogen bonding interactions between protonated 2-methylimidazolim cations, water molecules and polyoxoanions to form a 3D supramolecular architecture.

Photophysical Studies of Bioconjugated Ruthenium Metal-Ligand Complexes Incorporated in Phospholipid Membrane Bilayers

PubMed Central

Sharmin, Ayesha; Salassa, Luca; Rosenberg, Edward; Ross, J. B. Alexander; Abbott, Geoffrey; Black, Labe; Terwilliger, Michelle; Brooks, Robert

2013-01-01

Luminescent, mono-diimine, ruthenium complexes, [(H)Ru(CO)(PPh3)2(dcbpy)][PF6] (1, dcbpy = 4,4′-dicarboxy bipyridyl) and [(H)Ru(CO)(dppene)(5-amino-1,10-phen)][PF6] (2, dppene = bis diphenylphosphino-ethylene, phen = 9,10-phenanthroline), have been conjugated with 1,2-dihexadecanoyl-sn-glycero-3-phosphoethanolamine (DPPE) and with cholesterol in the case of 2. Compound 1 gives the bis-lipid derivative [(H)Ru(CO)(PPh3)2(dcbpy-N-DPPE2)][PF6] (3), while 2 provides the mono-lipid conjugate [(H)Ru(CO)(dppene)(1,10-phen-5-NHC(S)-N-DPPE)][ PF6] (4), and the cholesterol derivative [(H)Ru(CO)(dppene)(1,10-phen-5-NHC(O)OChol)][PF6] (5, Chol = cholesteryl), using standard conjugation techniques. These compounds were characterized by spectroscopic methods, and their photophysical properties were measured in organic solvents. The luminescence of lipid conjugates 3 and is quenched in organic solvents while compound 4 a weak, short-lived, blue-shifted emission in solution. The cholesterol conjugate shows the long-lived, microsecond-timescale emission associated with triplet metal-to-ligand charge-transfer (3MLCT) excited states. Incorporation of conjugate 3 in lipid bilayer vesicles restores the luminescence, but with blue shifts (~80 nm) accompanied by nanosecond-timescale lifetimes. In the vesicles conjugate 4 shows a similar short-lived and blue-shifted emission to that observed in solution but with increased intensity. Conjugation of the complex [(H)Ru(CO)(PhP2C2H4C(O)O-N-succinimidyl)2(bpy)][PF6] (6”) with DPPE gives the phosphine-conjugated complex [(H)Ru(CO)(PhP2C2H4C(O)-N-DPPE)2(bpy)][PF6] (7). Complex 7 also exhibits a short-lived and blue-shifted emission in solution and in vesicles as observed for 3 and 4. We have also conjugated the complex [Ru(bpy)2(5-amino-1,10-phenanthroline)][PF6]2 (8) with both cholesterol (9) and DPPE (10). Neither 9 nor the previously reported 10 exhibited the blue shifts observed for 3 and 4 when incorporated into LUVs. The anisotropies of the emissions of 3, 4 and 7 were also measured in LUVs and of 5 in both glycerol and LUVs. High fundamental anisotropies were observed for 3 and 4 and 7. PMID:24063694

Structural study of ethyl 3-methyl-9-oxo-3-azabicyclo63.3.19nonane-1-carboxylate by two-dimensional NMR spectroscopy

NASA Astrophysics Data System (ADS)

Arias-Pérez, M. S.; Alejo, A.; Gálvez, E.; Pérez, S. M.; Santos, M. J.

1995-04-01

Ethyl 3-methyl-9-oxo-3-azabicyclo[3.3.1]nonane-1-carboxylate has been studied by 1H, 13C and 2D NMR spectroscopy in order to establish its conformational behaviour. The combined use of COSY and 1H- 13C correlation spectra helped in the unambiguous and complete assignment of the bicyclic carbon and proton resonances. It is found that the piperidone ring displays a slightly fattened chair conformation with the N-methyl group in the equatorial position, while a twist-chair form seems to be favoured for the cyclohexanone one. Two preferred orientations migth be proposed for the ethoxycarbonyl moiety.

Abundances of ethylene oxide and acetaldehyde in hot molecular cloud cores

NASA Technical Reports Server (NTRS)

Nummelin, A.; Dickens, J. E.; Bergman, P.; Hjalmarson, A.; Irvine, W. M.; Ikeda, M.; Ohishi, M.

1998-01-01

We have searched for millimetre-wave line emission from ethylene oxide (c-C2H4O) and its structural isomer acetaldehyde (CH3CHO) in 11 molecular clouds using SEST. Ethylene oxide and acetaldehyde were detected through multiple lines in the hot cores NGC 6334F, G327.3-0.6, G31.41+0.31, and G34.3+0.2. Acetaldehyde was also detected towards G10.47+0.03, G322.2+0.6, and Orion 3'N, and one ethylene oxide line was tentatively detected in G10.47+0.03. Column densities and rotational excitation temperatures were derived using a procedure which fits the observed line intensifies by finding the minimum chi 2-value. The resulting rotational excitation temperatures of ethylene oxide and acetaldehyde are in the range 16-38 K, indicating that these species are excited in the outer, cooler parts of the hot cores or that the excitation is significantly subthermal. For an assumed source size of 20", the deduced column densities are (0.6-1)x10(14) cm-2 for ethylene oxide and (2-5)x10(14) cm-2 for acetaldehyde. The fractional abundances with respect to H2 are X[c-C2H4O]=(2-6)xl0(-10), and X[CH3CHO]=(0.8-3)x10(-9). The ratio X[CH3CHO]/X[c-C2H4O] varies between 2.6 (NGC 6334F) and 8.5 (G327.3-0.6). We also detected and analysed multiple transitions of CH3OH, CH3OCH3, C2H5OH, and HCOOH. The chemical, and possibly evolutionary, states of NGC 6334F, G327.3-0.6, G31.41+0.31, and G34.3+0.2 seem to be very similar.

Synthesis of boron suboxide from boron and boric acid under mild pressure and temperature conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiao, Xiaopeng; Jin, Hua; Ding, Zhanhui

2011-05-15

Graphical abstract: Well-crystallized and icosahedral B{sub 6}O crystals were prepared by reacting boron and boric acid at milder reaction conditions (1 GPa and 1300 {sup o}C for 2 h) as compared to previous work.. Research highlights: {yields} Well-crystallized icosahedral B{sub 6}O was synthesized by reacting boric acid and boron. {yields} The synthesis conditions (1 GPa and 1300 {sup o}C for 2 h) are milder in comparison with previous work. {yields} The more practical synthesis method may make B{sub 6}O as a potential substitute for diamond in industry. -- Abstract: Boron suboxide (B{sub 6}O) was synthesized by reacting boron and boricmore » acid (H{sub 3}BO{sub 3}) at pressures between 1 and 10 GPa, and at temperatures between 1300 and 1400 {sup o}C. The B{sub 6}O samples prepared were icosahedral with diameters ranging from 20 to 300 nm. Well-crystallized and icosahedral crystals with an average size of {approx}100 nm can be obtained at milder reaction conditions (1 GPa and 1300 {sup o}C for 2 h) as compared to previous work. The bulk B{sub 6}O sample was stable in air at 600 {sup o}C and then slowly oxidized up to 1000 {sup o}C. The relatively mild synthetic conditions developed in this study provide a more practical synthesis of B{sub 6}O, which may potentially be used as a substitute for diamond in industry as a new superhard material.« less

Effect of storage temperatures on growth and survival of Escherichia coli O157: H7 inoculated in foods from a neotropical environment.

PubMed

Arias, M L; Monge-Rojas, R; Chaves, C; Antillón, F

2001-06-01

Escherichia coli O157: H7 has emerged as a new pathogen and is found worldwide. We studied the effect of several storage temperatures on the survival of this bacterium in common foods from a neotropical environment (Costa Rica) because at least seven clinical cases have been reported from the country, and no epidemiological link or probable food association has been described. High (10(6)-10(8) CFU/ml) and low (10(4)-10(6) CFU/ml) populations of E. coli were inoculated (three replications) in ground meat, chopped cabbage, chicken giblets and pasteurized milk and incubated at 0, 6 and 12 degrees C for 24, 48 and 72 h. Vegetables and milk were also stored at 22 degrees C for the same periods. The E. coli O157: H7 enumeration was done according to the methodology described in the Bacteriological Analytical Manual. Populations of E. coli O157: H7 showed either an increasing or decreasing trend, according to temperature, time or food base. Our data indicate that E. coli O157: H7 is capable of surviving and growing in meat, cabbage, milk and chicken giblets; food items commonly consumed by Costa Ricans.

Polycyclic ferrocenyl(dihydro)thiazepine derivatives: Diastereo-selective synthesis, characterization, electrochemical behavior, theoretical and biological investigation.

PubMed

Sánchez García, Jessica J; Toledano-Magaña, Yanis; Flores-Alamo, Marcos; Martínez-Klimova, Elena; Galindo-Murillo, Rodrigo; Hernández-Ayala, Luis F; Ortiz-Frade, Luis; García-Ramos, Juan C; Klimova, Elena I

2017-01-01

The reaction of E-2-ferrocenylmethylidenetetralones and E,E-2,6-bis-(ferrocenylmethylidene)-cyclohexanone with 2-aminothiophenol proceed with high diastereoselectivity, forming the ~4.5:1 mixture of trans- and cis-isomers of polycyclic ferrocenylthiazepines, respectively. The reactions of E,E-2,5-bis-(ferrocenylmethylidene)cyclopentanone and E,E-3,5-bis-(ferrocenylmethylidene)-1-methyl-4-piperidone with 2-aminothiophenol take place stereo specifically to form the diastereomeric tricyclic thiazepines of cis- and trans-configuration, respectively. The structures of the obtained compounds were established by IR, 1 H and 13 C NMR spectroscopy and mass-spectrometry. The structures of the trans-tetralino[1,2a]-, trans-5,7-dimethyltetralino[1,2a]-2-ferrocenyl [1,5]benzo-2,3-dihydrothiazepines and cis-5-ferrocenyl-methylidenecyclopentano[1,2a]-2-ferrocenyl- [1,5]benzo-2,3-dihydrothiazepine were confirmed by X-ray diffraction analysis. An electrochemical study reveals that the diferrocenyl derivatives belong to a Class I compounds of the Robin-Day classification. This behavior is explained by the analysis of frontier orbitals as calculated by density functional theory, showing that only one ferrocenyl unit participates in the generation of HOMO and LUMO orbitals. Compounds 4a and 4c showed similar capacity to inhibit the proliferation of HM1: IMSS trophozoite cultures than the first choice drug for human amoebiasis treatment, metronidazole. Morphological changes induced in the trophozoites after drug exposure suggest a redox in balance as the probable mechanism of the parasite death. Copyright © 2016 Elsevier Inc. All rights reserved.

Evolution of Interstellar Grains

NASA Technical Reports Server (NTRS)

Allamandola, Lou J.; DeVincenzi, Donald L. (Technical Monitor)

1998-01-01

During the past two decades observations combined with laboratory simulations, have revolutionized our understanding of interstellar ice and dust, the raw materials from which planets, comets and stars form. Most interstellar material is concentrated in large molecular clouds where simple molecules are formed by dust-grain and gas-phase reactions. Gaseous species striking the cold (10K) dust stick, forming an icy grain mantle. This accretion, coupled with UV photolysis, produces a complex chemical mixture containing volatile, non-volatile, and isotopically fractionated species. Ices in molecular clouds contain the very simple molecules H2O, CH3OH, CO, CO2, H2, and perhaps some NH3 and H2CO, as well as more complex species. The evidence for these compounds, as well as carbon-rich materials, will be reviewed and the possible connections with comets and meteorites will be presented in the first part of the talk . The second part of the presentation will focus on interstellar/precometary ice photochemical evolution and the species likely to be found in comets. The chemical composition and photochemical evolution of realistic interstellar/pre-cometary ice analogs will be discussed. Ultraviolet photolysis of these ices produces H2, H2CO, CO2, CO, CH4, HCO, and more complex molecules. When ices representative of interstellar grains and comets are exposed to UV radiation at low temperature a series of moderately complex organic molecules are formed in the ice including: CH3CH2OH (ethanol), HC(=O)NH2 (formamide), CH3C(=O)NH2 (acetamide), and R-C=N (nitriles). Several of these are already known to be in the interstellar medium, and their presence indicates the importance of grain processing. After warming to room temperature an organic residue remains. This is composed primarily of hexamethylenetetramine (HMT, C6H12N4), with lesser amounts of polyoxymethylene-related species (POMs), amides, and ketones. This is in sharp contrast to the organic residues produced by irradiating unrealistic interstellar ice analogs or thermally promoted polymerization-type reactions in unirradiated realistic ice mixtures.

Single-crystal X-ray diffraction and NMR crystallography of a 1:1 cocrystal of dithianon and pyrimethanil.

PubMed

Pöppler, Ann Christin; Corlett, Emily K; Pearce, Harriet; Seymour, Mark P; Reid, Matthew; Montgomery, Mark G; Brown, Steven P

2017-03-01

A single-crystal X-ray diffraction structure of a 1:1 cocrystal of two fungicides, namely dithianon (DI) and pyrimethanil (PM), is reported [systematic name: 5,10-dioxo-5H,10H-naphtho[2,3-b][1,4]dithiine-2,3-dicarbonitrile-4,6-dimethyl-N-phenylpyrimidin-2-amine (1/1), C 14 H 4 N 2 O 2 S 2 ·C 12 H 13 N 2 ]. Following an NMR crystallography approach, experimental solid-state magic angle spinning (MAS) NMR spectra are presented together with GIPAW (gauge-including projector augmented wave) calculations of NMR chemical shieldings. Specifically, experimental 1 H and 13 C chemical shifts are determined from two-dimensional 1 H- 13 C MAS NMR correlation spectra recorded with short and longer contact times so as to probe one-bond C-H connectivities and longer-range C...H proximities, whereas H...H proximities are identified in a 1 H double-quantum (DQ) MAS NMR spectrum. The performing of separate GIPAW calculations for the full periodic crystal structure and for isolated molecules allows the determination of the change in chemical shift upon going from an isolated molecule to the full crystal structure. For the 1 H NMR chemical shifts, changes of 3.6 and 2.0 ppm correspond to intermolecular N-H...O and C-H...O hydrogen bonding, while changes of -2.7 and -1.5 ppm are due to ring current effects associated with C-H...π interactions. Even though there is a close intermolecular S...O distance of 3.10 Å, it is of note that the molecule-to-crystal chemical shifts for the involved sulfur or oxygen nuclei are small.

The reaction of H2O2 with NO2 and NO

NASA Technical Reports Server (NTRS)

Gray, D.; Lissi, E.; Heicklen, J.

1972-01-01

The reactions of NO and NO2 with H2O2 have been examined at 25 C. Reaction mixtures were monitored by continuously bleeding through a pinhole into a monopole mass spectrometer. NO2 was also monitored by its optical absorption in the visible part of the spectrum. Reaction mixtures containing initially 1.5 - 2.5 torr of NO2 and 0.8 - 1.4 torr of H2O2 or 1 - 12 torr of NO and 0.5 - 1.5 torr of H2O2 were studied. The H2O2 - NO reaction was complex. There was an induction period followed by a marked acceleration in reactant removal. The final products of the reaction, NO2, probably H2O, and possibly HONO2 were produced mainly after all the H2O2 was removed. The HONO intermediate was shown to disproportionate to NO2 + NO + H2O in a relatively slow first order reaction. The acceleration in H2O2 removal after the NO - H2O2 reaction is started is caused by NO2 catalysis.

Food-grade submicrometer particles from salts prepared using ethanol-in-oil mixtures.

PubMed

Paques, Jerome P; van der Linden, Erik; Sagis, Leonard M C; van Rijn, Cees J M

2012-08-29

A simple method for preparing food-grade particles in the submicrometer range of ethanol soluble salts using ethanol-in-oil (E/O) mixtures is described. Salts CaCl2·2H2O and MgCl2·6H2O were dissolved in ethanol that subsequently was mixed with a medium-chain triglyceride oil phase. It was found that type and concentration of salt have a significant influence on the miscibility of ethanol and oil phase and on the stability of E/O mixtures. The ethanol phase was evaporated from the mixture at elevated temperatures, and salt particles with dimensions in the submicrometer range (6-400 nm) remained suspended in the oil phase. It was found that the concentration of salt and volume fraction of ethanol in MCT oil have a significant influence on the size distribution of salt particles. The size of CaCl2 and MgCl2 submicrometer particles was ascertained by scanning electron microscopy and dynamic light scattering.

Near-limit propagation of gaseous detonations in narrow annular channels

NASA Astrophysics Data System (ADS)

Gao, Y.; Ng, H. D.; Lee, J. H. S.

2017-03-01

New results on the near-limit behaviors of gaseous detonations in narrow annular channels are reported in this paper. Annular channels of widths 3.2 and 5.9 mm were made using circular inserts in a 50.8 mm-diameter external tube. The length of each annular channel was 1.8 m. Detonations were initiated in a steel driver tube where a small volume of a sensitive C2H2+ 2.5O2 mixture was injected to facilitate detonation initiation. A 2 m length of circular tube with a 50.8 mm diameter preceded the annular channel so that a steady Chapman-Jouguet (CJ) detonation was established prior to entering the annular channel. Four detonable mixtures of C2H2 {+} 2.5O2 {+} 85 % Ar, C2H2 {+} 2.5O2 {+} 70 % Ar, C3H8 {+} 5O2, and CH4 {+} 2O2 were used in the present study. Photodiodes spaced 10 cm throughout the length of both the annular channel and circular tube were used to measure the detonation velocity. In addition, smoked foils were inserted into the annular channel to monitor the cellular structure of the detonation wave. The results show that, well within the detonability limits, the detonation wave propagates along the channel with a small local velocity fluctuation and an average global velocity can be deduced. The average detonation velocity has a small deficit of 5-15 % far from the limits and the velocity rapidly decreases to 0.7V_{CJ}-0.8V_{CJ} when the detonation propagates near the limit. Subsequently, the fluctuation of local velocity also increases as the decreasing initial pressure approaches the limit. In the two annular channels used in this work, no galloping detonations were observed for both the stable and unstable mixtures tested. The present study also confirms that single-headed spinning detonation occurs at the limit, as in a circular tube, rather than the up and down "zig zag" mode in a two-dimensional, rectangular channel.

Preconditioning of the YSZ-NiO Fuel Cell Anode in Hydrogenous Atmospheres Containing Water Vapor.

PubMed

Vasyliv, Bogdan; Podhurska, Viktoriya; Ostash, Orest

2017-12-01

The YSZ-NiO ceramics for solid oxide fuel cells (SOFCs) anode have been investigated. A series of specimens were singly reduced in a hydrogenous atmosphere (Ar-5 vol% H 2 mixture) at 600 °C under the pressure of 0.15 MPa or subjected to 'reduction in the mixture-oxidation in air' (redox) cycling at 600 °C. The YSZ-Ni cermets formed in both treatment conditions were then aged in 'water vapor in Ar-5 vol% H 2 mixture' atmosphere at 600 °C under the pressure of 0.15 MPa. Additionally, the behaviour of the as-received material in this atmosphere was studied. It was revealed that small amount of water vapor in Ar-5 vol% H 2 mixture (water vapor pressure below 0.03 MPa) does not affect the reduction of the nickel phase in the YSZ-NiO ceramics, but causes some changes in the YSZ-Ni cermet structure. In particular, nanopore growth in tiny Ni particles takes place. At higher concentration of water vapor in the mixture (water vapor pressure above 0.03-0.05 MPa), converse changes in the kinetics of reduction occur. The best physical and mechanical properties were revealed for the material treated by redox cycling after holding at 600 °C in water depleted gas mixture. The dual effect of water vapor on nickel-zirconia anode behaviour is discussed basing on scanning electron microscopy analysis data, material electrical conductivity, and strength.

The first 3':5'-cyclic nucleotide-amino acid complex: L-His-cIMP.

PubMed

Slepokura, Katarzyna

2012-08-01

In the crystal structure of the L-His-cIMP complex, i.e. L-histidinium inosine 3':5'-cyclic phosphate [systematic name: 5-(2-amino-2-carboxyethyl)-1H-imidazol-3-ium 7-hydroxy-2-oxo-6-(6-oxo-6,9-dihydro-1H-purin-9-yl)-4a,6,7,7a-tetrahydro-4H-1,3,5,2λ(5)-furo[3,2-d][1,3,2λ(5)]dioxaphosphinin-2-olate], C(6)H(10)N(3)O(2)(+)·C(10)H(10)N(4)O(7)P(-), the Hoogsteen edge of the hypoxanthine (Hyp) base of cIMP and the Hyp face are engaged in specific amino acid-nucleotide (His···cIMP) recognition, i.e. by abutting edge-to-edge and by π-π stacking, respectively. The Watson-Crick edge of Hyp and the cIMP phosphate group play a role in nonspecific His···cIMP contacts. The interactions between the cIMP anions (anti/C3'-endo/trans-gauche/chair conformers) are realized mainly between riboses and phosphate groups. The results for this L-His-cIMP complex, compared with those for the previously reported solvated L-His-IMP crystal structure, indicate a different nature of amino acid-nucleotide recognition and interactions upon the 3':5'-cyclization of the nucleotide phosphate group.

Reactivity of triruthenium thiophyne and furyne clusters: competitive S-C and P-C bond cleavage reactions and the generation of highly unsymmetrical alkyne ligands.

PubMed

Uddin, Md Nazim; Begum, Noorjahan; Hassan, Mohammad R; Hogarth, Graeme; Kabir, Shariff E; Miah, Md Arzu; Nordlander, Ebbe; Tocher, Derek A

2008-11-28

The synthesis and reactivity of the thiophyne and furyne clusters [Ru3(CO)7(mu-dppm)(mu3-eta2-C4H2E)(mu-P(C4H3E)2)(mu-H)] (E = S, O) is reported. Addition of P(C4H3E)3 to [Ru3(CO)10(mu-dppm)] (1) at room temperature in the presence of Me3NO gives simple substitution products [Ru3(CO)9(mu-dppm)(P(C4H3E)3)] (E = S, 2; E = O, 3). Mild thermolysis in the presence of further Me3NO affords the thiophyne and furyne complexes [Ru3(CO)7(mu-dppm)(mu3-eta2-C4H2E)(mu-P(C4H3E)2)(mu-H)] (E = S, 4; E = O, 6) resulting from both carbon-hydrogen and carbon-phosphorus bond activation. In each the C4H2E (E = S, O) ligand donates 4-electrons to the cluster and the rings are tilted with respect to the mu-dppm and the phosphido-bridged open triruthenium unit. Heating 4 at 80 degrees C leads to the formation of the ring-opened cluster [Ru3(CO)5(mu-CO)(mu-dppm)(mu3-eta3-SC4H3)(mu-P(C4H3S)2)] (5) resulting from carbon-sulfur bond scission and carbon-hydrogen bond formation and containing a ring-opened mu3-eta3-1-thia-1,3-butadiene ligand. In contrast, a similar thermolysis of 3 affords the phosphinidene cluster [Ru3(CO)7(mu-dppm)(mu3-eta2-C4H2O)(mu3-P(C4H3O))] (7) resulting from a second phosphorus-carbon bond cleavage and (presumably) elimination of furan. Treatment of 4 and 6 with PPh3 affords the simple phosphine-substituted products [Ru3(CO)6(PPh3)(mu-dppm)(mu3-eta2-C4H2E)(mu-P(C4H3E)2)(mu-H)] (E = S, 8; E = O, 9). Both thiophyne and furyne clusters 4 and 6 readily react with hydrogen bromide to give [Ru3(CO)6Br(mu-Br)(mu-dppm)(mu3-eta2-eta1-C4H2E)(mu-P(C4H3E)2)(mu-H)] (E = S, 10; E = O, 11) containing both terminal and bridging bromides. Here the alkynes bind in a highly unsymmetrical manner with one carbon acting as a bridging alkylidene and the second as a terminally bonded Fisher carbene. As far as we are aware, this binding mode has only previously been noted in ynamine complexes or those with metals in different oxidation states. The crystal structures of seven of these new triruthenium clusters have been carried out, allowing a detailed analysis of the relative orientations of coordinated ligands.

Laboratory study of polychlorinated biphenyl (PCB) contamination and mitigation in buildings; Part 1. Emissions from selected primary sources

EPA Science Inventory

Polychlorinated biphenyls (PCBs) are a class of 209 organic compounds, known as congeners, with the chemical formula of C12H1O-xClx, where x is the number of chlorine atoms in the range of 1 to 10. Different mixtures of these congeners were sold under many brands and trade names ...

Organometallic oxides: Preparation, structure, and chemical and physical properties of paramagnetic ((. eta. -C sub 5 H sub 5 )NbCl(. mu. -A)) sup 3 (. mu. sub 3 -OH)(. mu. sub 3 -O) (A = Cl, OH) and other oxo-hydroxo clusters of niobium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bottomley, F.; Keizer, P.N.; White, P.S.

Hydrolysis of Cp{prime}NbCl{sub 4} (Cp{prime} = {eta}{sup 5}-C{sub 5}H{sub 5} (Cp), {eta}-C{sub 5}H{sub 4}Me (Cp{sup 1})) in tetrahydrofuran (THF) gave a mixture of products of general formula (Cp{prime}NbL{sub 4}){sub 2}({mu}-O), where L{sub 4} is a combination of H{sub 2}O and terminal or bridging Cl that gives eight-coordinate, pentavalent, niobium. For Cp{prime} = Cp, a major constituent of the mixture is (CpNb(H{sub 2}O)Cl{sub 3}){sub 2}({mu}-O) {times} 2THF {times} 0.05Et{sub 2}O (1), the structure of which was determined by X-ray diffraction. Reduction of (Cp{prime}NbL{sub 4}){sub 2}({mu}-O) with aluminum powder gave the cluster (Cp{prime}NbCl({mu}-Cl)){sub 3}({mu}{sub 3}-OH)({mu}{sub 3}-O) (2). The structure of 2 (Cp{prime}more » = Cp) as the THF adduct was determined by X-ray diffraction. Crystal data: monoclinic; P2{sub 1}/c; a = 9.966 (1) {angstrom}, b = 12.471 (2) {angstrom}, c = 20.321 (2) {angstrom}, {beta} = 93.86 (1){degree}.« less

Gallium(III)-Containing, Sandwich-Type Heteropolytungstates: Synthesis, Solution Characterization, and Hydrolytic Studies toward Phosphoester and Phosphoanhydride Bond Cleavage.

PubMed

Kandasamy, Balamurugan; Vanhaecht, Stef; Nkala, Fiona Marylyn; Beelen, Tessa; Bassil, Bassem S; Parac-Vogt, Tatjana N; Kortz, Ulrich

2016-09-19

The gallium(III)-containing heteropolytungstates [Ga4(H2O)10(β-XW9O33)2](6-) (X = As(III), 1; Sb(III), 2) were synthesized in aqueous acidic medium by reaction of Ga(3+) ions with the trilacunary, lone-pair-containing [XW9O33](9-). Polyanions 1 and 2 are isostructural and crystallized as the hydrated sodium salts Na6[Ga4(H2O)10(β-AsW9O33)2]·28H2O (Na-1) and Na6[Ga4(H2O)10(β-SbW9O33)2]·30H2O (Na-2) in the monoclinic space group P21/c, with unit cell parameters a = 16.0218(12) Å, b = 15.2044(10) Å, c = 20.0821(12) Å, and β = 95.82(0)°, as well as a = 16.0912(5) Å, b = 15.2178(5) Å, c = 20.1047(5) Å, and β = 96.2(0)°, respectively. The corresponding tellurium(IV) derivative [Ga4(H2O)10(β-TeW9O33)2](4-) (3) was also prepared, by direct reaction of sodium tungstate, tellurium(IV) oxide, and gallium nitrate. Polyanion 3 crystallized as the mixed rubidium/sodium salt Rb2Na2[Ga4(H2O)10(β-TeW9O33)2]·28H2O (RbNa-3) in the triclinic space group P1̅ with unit cell parameters a = 12.5629(15) Å, b = 13.2208(18) Å, c = 15.474(2) Å, α = 80.52(1)°, β = 84.37(1)°, and γ = 65.83(1)°. All polyanions 1-3 were characterized in the solid state by single-crystal XRD, FT-IR, TGA, and elemental analysis, and polyanion 2 was also characterized in solution by (183)W NMR and UV-vis spectroscopy. Polyanion 2 was used as a homogeneous catalyst toward adenosine triphosphate (ATP) and the DNA model substrate 4-nitrophenylphosphate, monitored by (1)H and (31)P NMR spectroscopy. The encapsulated gallium(III) centers in 2 promote the Lewis acidic synergistic activation of the hydrolysis of ATP and DNA model substrates at a higher rate in near-physiological conditions. A strong interaction of 2 with the P-O bond of ATP was evidenced by changes in chemical shift values and line broadening of the (31)P nucleus in ATP upon addition of the polyanion.

NCI calculations for understanding a physical phase transition in (C6H14N2)[Mn(H2O)6](SeO4)2

NASA Astrophysics Data System (ADS)

Naïli, Houcine; François, Michel; Norquist, Alexander J.; Rekik, Walid

2017-12-01

An organically templated manganese selenate, (C6H14N2)[Mn(H2O)6](SeO4)2, has been synthesized by slow evaporation and crystallographically characterized. The title compound crystallizes at room temperature in the monoclinic centrosymmetric space group P21/n, with the following unit cell parameters: a = 7.2373(4) Å; b = 12.5600(7) Å; c = 10.1945(7) Å; β = 91.155(4)°, V = 926.50(10) Å3and Z = 2. Its crystal structure is built of manganese(II) cations coordinated by six water molecules in octahedral geometry, disordered dabcodiium cations and selenate anions, resulting in an extensive hydrogen-bonding network. Differential scanning calorimetry (DSC) measurement indicated that the precursor undergoes a reversible phase transition at about 216 and 218 K during the cooling and heating processes respectively. Below this temperature the title compound is noncentrosymmetric with space group P21 and lattice parameters a = 7.2033(8) Å; b = 12.4981(13) Å; c = 10.0888(11) Å; β = 91.281(2)°, V = 908.04(17) Å3 and Z = 2. The disorder-order transformation of the C atoms of (C6H14N2)2+ cation may drive the structural phase transition. The low temperature phase obtained by breaking symmetry presents a fully ordered structure. The noncovalent interaction (NCI) method was used not only to locate, quantify, and visualize intermolecular interactions in the high and low temperature phases but also to confirm the phase transition detected by DSC measurement. The thermal decomposition of this new compound proceeds through four stages giving rise to the manganese oxide as final product at 850 °C.

Synthesis and structure of tetranuclear orthometallated Pd(II) complexes derived from bis-iminophosphoranes.

PubMed

Bielsa, Raquel; Navarro, Rafael; Soler, Tatiana; Urriolabeitia, Esteban P

2008-04-07

The reaction of Pd(OAc)2 with bis-iminophosphoranes Ph3P=NCH2CH2CH2N=PPh3 (1a), [C6H4(C(O)N=PPh3)2-1,3] (1b) and [C6H4(C(O)N=PPh3)2-1,2] (1c), gives the orthopalladated tetranuclear complexes [{Pd(mu-Cl){C6H4(PPh2=NCH2-kappa-C,N)-2}}2CH2]2 (2a) [{Pd(mu-OAc){C6H4(PPh2=NC(O)-kappa-C,N)-2}}2C6H4-1',3']2 (2b) and [{Pd(mu-OAc){C6H4(PPh2=NC(O)-kappa-C,N)-2}}2C6H4-1',2']2 (2c). The reaction takes place in CH2Cl2 for 1a, but must be performed in glacial acetic acid for 1b and 1c. The process implies in all cases the activation of a C-H bond on a Ph ring of the phosphonium group, with concomitant formation of endo complexes. This is the expected behaviour for 1a, but for 1b and 1c reverses the exo orientation observed in other ketostabilized iminophosphoranes. The influence of the solvent in the orientation of the reaction is discussed. The dinuclear acetylacetonate complexes [{Pd(acac-O,O'){C6H4(PPh2=NCH2-kappa-C,N)-2}}2CH2] (3a), [{Pd(acac-O,O'){C6H4(PPh2=NC(O)-kappa-C,N)-2}}2C6H4-1',3'] (3b) and [{Pd(acac-O,O'){C6H4(PPh2=NC(O)-kappa-C,N)-2}}2C6H4-1',2'] (3c) have been obtained from the halide-bridging tetranuclear derivatives. The X-ray crystal structure of [3c.4CHCl3] is also reported.

Electron impact ionisation cross section for organoplatinum compounds

NASA Astrophysics Data System (ADS)

Mahato, Dibyendu; Naghma, Rahla; Alam, Mohammad Jane; Ahmad, Shabbir; Antony, Bobby

2016-11-01

This article reports electron impact ionisation cross sections for platinum-based drugs viz., cisplatin (H6N2Cl2Pt), carboplatin (C6H12N2O4Pt), oxaliplatin (C8H14N2O4Pt), nedaplatin (C2H8N2O3Pt) and satraplatin (C10H22ClN2O4Pt) complexes used in the cancer chemotherapy. The multi-scattering centre spherical complex optical potential formalism is used to obtain the inelastic cross section for these large molecules upon electron impact. The ionisation cross section is derived from the inelastic cross section employing complex scattering potential-ionisation contribution method. Comparison is made with previous results, where ever available and overall a reasonable agreement is observed. This is the first attempt to report total ionisation cross sections for nedaplatin and satraplatin complexes.

A highly sensitive electrochemical biosensor for catechol using conducting polymer reduced graphene oxide-metal oxide enzyme modified electrode.

PubMed

Sethuraman, V; Muthuraja, P; Anandha Raj, J; Manisankar, P

2016-10-15

The fabrication, characterization and analytical performances were investigated for a catechol biosensor, based on the PEDOT-rGO-Fe2O3-PPO composite modified glassy carbon (GC) electrode. The graphene oxide (GO) doped conducting polymer poly (3,4-ethylenedioxythiophene) (PEDOT) was prepared through electrochemical polymerization by potential cycling. Reduction of PEDOT-GO was carried out by amperometric method. Fe2O3 nanoparticles were synthesized in ethanol by hydrothermal method. The mixture of Fe2O3, PPO and glutaraldehyde was casted on the PEDOT-rGO electrode. The surface morphology of the modified electrodes was studied by FE-SEM and AFM. Cyclic voltammetric studies of catechol on the enzyme modified electrode revealed higher reduction peak current. Determination of catechol was carried out successfully by Differential Pulse Voltammetry (DPV) technique. The fabricated biosensor investigated shows a maximum current response at pH 6.5. The catechol biosensor exhibited wide sensing linear range from 4×10(-8) to 6.20×10(-5)M, lower detection limit of 7×10(-9)M, current maxima (Imax) of 92.55µA and Michaelis-Menten (Km) constant of 30.48µM. The activation energy (Ea) of enzyme electrode is 35.93KJmol(-1) at 50°C. There is no interference from d-glucose and l-glutamic acid, ascorbic acid and o-nitrophenol. The PEDOT-rGO-Fe2O3-PPO biosensor was stable for at least 75 days when stored in a buffer at about 4°C. Copyright © 2015 Elsevier B.V. All rights reserved.

Hydrothermal syntheses, structures and characterizations of three one-dimensional polyoxomolybdates with 4,4'-dimethylenebiphenyl diphosphonic acid as bridge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Huishuang; Fu Ruibiao; Zhang Jianjun

2005-05-15

Three heterometallic 1-D polymers, [{l_brace}Ni(1,10-phen){sub 2}(H{sub 2}O){r_brace}{sub 2} {l_brace}(Mo{sub 5}O{sub 15})(4,4'-dbp){r_brace}.(5.75H{sub 2}O)] (4,4'-dbp=O{sub 3}PCH{sub 2}C{sub 6}H{sub 4}C{sub 6}H{sub 4}CH{sub 2}PO{sub 3}) (1), [{l_brace}Co(1,10-phen){sub 2}(H{sub 2}O){r_brace}{sub 2} {l_brace}(Mo{sub 5}O{sub 15})(4,4'-dbp){r_brace}.(5.5H{sub 2}O)] (2) and [{l_brace}Ni(2,2'-bpy){sub 3}{r_brace}{l_brace}Ni(2,2'-bpy){sub 2}(H{sub 2}O){r_brace} {l_brace}(Mo{sub 5}O{sub 15})(4,4'-dbp){r_brace}.(4.75H{sub 2}O)] (3), have been synthesized under hydrothermal conditions. Their structures were determined by single crystal X-ray diffraction. The 1-D chains is constructed of [Mo{sub 5}O{sub 15}(4,4'-dbp)]{sup 4-} units, which are further decorated and charge compensated by [M(1,10-phen){sub 2}] (M=Ni, Co) or [Ni(2,2'-bpy){sub 2}] subunits. The thermogravimetric analyses and magnetic properties of 1 and 2 were studied.

Atmospheric fates of Criegee intermediates in the ozonolysis of isoprene.

PubMed

Nguyen, Tran B; Tyndall, Geoffrey S; Crounse, John D; Teng, Alexander P; Bates, Kelvin H; Schwantes, Rebecca H; Coggon, Matthew M; Zhang, Li; Feiner, Philip; Milller, David O; Skog, Kate M; Rivera-Rios, Jean C; Dorris, Matthew; Olson, Kevin F; Koss, Abigail; Wild, Robert J; Brown, Steven S; Goldstein, Allen H; de Gouw, Joost A; Brune, William H; Keutsch, Frank N; Seinfeld, John H; Wennberg, Paul O

2016-04-21

We use a large laboratory, modeling, and field dataset to investigate the isoprene + O3 reaction, with the goal of better understanding the fates of the C1 and C4 Criegee intermediates in the atmosphere. Although ozonolysis can produce several distinct Criegee intermediates, the C1 stabilized Criegee (CH2OO, 61 ± 9%) is the only one observed to react bimolecularly. We suggest that the C4 Criegees have a low stabilization fraction and propose pathways for their decomposition. Both prompt and non-prompt reactions are important in the production of OH (28% ± 5%) and formaldehyde (81% ± 16%). The yields of unimolecular products (OH, formaldehyde, methacrolein (42 ± 6%) and methyl vinyl ketone (18 ± 6%)) are fairly insensitive to water, i.e., changes in yields in response to water vapor (≤4% absolute) are within the error of the analysis. We propose a comprehensive reaction mechanism that can be incorporated into atmospheric models, which reproduces laboratory data over a wide range of relative humidities. The mechanism proposes that CH2OO + H2O (k(H2O)∼ 1 × 10(-15) cm(3) molec(-1) s(-1)) yields 73% hydroxymethyl hydroperoxide (HMHP), 6% formaldehyde + H2O2, and 21% formic acid + H2O; and CH2OO + (H2O)2 (k(H2O)2∼ 1 × 10(-12) cm(3) molec(-1) s(-1)) yields 40% HMHP, 6% formaldehyde + H2O2, and 54% formic acid + H2O. Competitive rate determinations (kSO2/k(H2O)n=1,2∼ 2.2 (±0.3) × 10(4)) and field observations suggest that water vapor is a sink for greater than 98% of CH2OO in a Southeastern US forest, even during pollution episodes ([SO2] ∼ 10 ppb). The importance of the CH2OO + (H2O)n reaction is demonstrated by high HMHP mixing ratios observed over the forest canopy. We find that CH2OO does not substantially affect the lifetime of SO2 or HCOOH in the Southeast US, e.g., CH2OO + SO2 reaction is a minor contribution (<6%) to sulfate formation. Extrapolating, these results imply that sulfate production by stabilized Criegees is likely unimportant in regions dominated by the reactivity of ozone with isoprene. In contrast, hydroperoxide, organic acid, and formaldehyde formation from isoprene ozonolysis in those areas may be significant.

Second International Conference on Snow Engineering.

DTIC Science & Technology

1992-12-01

the Wiinter 10 aa 0. cS," 0’ 00 < 0~ - ap aa aa a a a a a - - -(p,,l O IID A (11 OuI JDI (3/ill) JJDMIM ol 0 8 N~ ~ T -\\----- w to co ad ba a C. ’ C6...V {l H 2.2 󈧐-2. *, 10 - C @ 2.0 + ® 8 - A • _ -1.8 06 C, 1.6 x 1.4 "" - - . 1.2 " 0 t 0 x 1.2 - Type! Type I Typelll Normal Lognormal 1.0 : Annual...n ua cO000 e rP s dxtrep e Snow Depths 0 - (an) 1500 200 300 400 Fig. 8 . Relationship between W... and H,,,, Wim i (kgf/ni) gN r MRI values of A : 10

Solar-based detoxification of phenol and p-nitrophenol by sequential TiO2 photocatalysis and photosynthetically aerated biological treatment.

PubMed

Essam, Tamer; Aly Amin, Magdy; El Tayeb, Ossama; Mattiasson, Bo; Guieysse, Benoit

2007-04-01

Simulated solar UV/TiO(2) photocatalysis was efficient to detoxify a mixture of 100 mgphenoll(-1) and 50 mgp-nitrophenol (PNP) l(-1) and allow the subsequent biodegradation of the remaining pollutants and their photocatalytic products under photosynthetic aeration with Chlorella vulgaris. Photocatalytic degradation of phenol and PNP was well described by pseudo-first order kinetics (r(2)>0.98) with removal rate constants of 1.9x10(-4) and 2.8x10(-4)min(-1), respectively, when the pollutants were provided together and 5.7x10(-4) and 9.7x10(-4)min(-1), respectively, when they were provided individually. Photocatalytic pre-treatment of the mixture during 60 h removed 50+/-1% and 62+/-2% of the phenol and PNP initially present but only 11+/-3% of the initial COD. Hydroquinone, nitrate and catechol were identified as PNP photocatalytic products and catechol and hydroquinone as phenol photocatalytic products. Subsequent biological treatment of the pre-treated samples removed the remaining contaminants and their photocatalytic products as well as 81-83% of the initial COD, allowing complete detoxification of the mixture to C. vulgaris. Similar detoxification efficiencies were recorded after biological treatment of the irradiated mixture with activated sludge microflora or with an acclimated consortia composed of a phenol-degrading Alcaligenes sp. and a PNP-degrading Arthrobacter sp., although the acclimated strains biodegraded the remaining pollutants faster. Biological treatment of the non-irradiated mixture was inefficient due to C. vulgaris inhibition.

Ab initio molecular dynamics study of fluid H2O-CO2 mixture in broad pressure-temperature range

NASA Astrophysics Data System (ADS)

Fu, Jie; Zhao, Jijun; Plyasunov, Andrey V.; Belonoshko, Anatoly B.

2017-11-01

Properties of H2O and CO2 fluid and their mixtures under extreme pressures and temperatures are poorly known yet critically important in a number of applications. Several hundreds of first-principles molecular dynamics (FPMD) runs have been performed to obtain the pressure-volume-temperature (P-V-T) data on supercritical H2O, CO2, and H2O-CO2 mixtures. The pressure-temperature (P-T) range are from 0.5 GPa to 104 GPa (48.5 GPa for CO2) and from 600 K to 4000 K. Based on these data, we evaluate several existing equations of state (EOS) for the fluid H2O, CO2, and H2O-CO2 mixture. The results show that the EOS for H2O from Belonoshko et al. [Geochim. Cosmochim. Acta 55, 381-387; Geochim. Cosmochim. Acta 55, 3191-3208; Geochim. Cosmochim. Acta 56, 3611-3626; Comput. Geosci. 18, 1267-1269] not only can be used in the studied P-T range but also is accurate enough to be used for prediction of P-V-T data. In addition, IAPWS-95 EOS for H2O shows excellent extrapolation behavior beyond 1.0 GPa and 1273 K. However, for the case of CO2, none of the existing EOS produces data in agreement with the FPMD results. We created new EOS for CO2. The precision of the new EOS is tested by comparison to the calculated P-V-T data, fugacity coefficient of the CO2 fluid derived from high P-T experimental data as well as to the (very scarce) experimental volumetric data in the high P-T range. On the basis of our FPMD data we created a new EOS for H2O-CO2 mixture. The new EOS for the mixture is in reasonable agreement with experimental data.

Chemical Substitution-Induced and Competitive Formation of 6H and 3C Perovskite Structures in Ba3-xSrxZnSb2O9: The Coexistence of Two Perovskites in 0.3 ≤ x ≤ 1.0.

PubMed

Li, Jing; Jiang, Pengfei; Gao, Wenliang; Cong, Rihong; Yang, Tao

2017-11-20

6H and 3C perovskites are important prototype structures in materials science. We systemically studied the structural evolution induced by the Sr 2+ -to-Ba 2+ substitution to the parent 6H perovskite Ba 3 ZnSb 2 O 9 . The 6H perovskite is only stable in the narrow range of x ≤ 0.2, which attributes to the impressibility of [Sb 2 O 9 ]. The preference of 90° Sb-O-Sb connection and the strong Sb 5+ -Sb 5+ electrostatic repulsion in [Sb 2 O 9 ] are competitive factors to stabilize or destabilize the 6H structure when chemical pressure was introduced by Sr 2+ incorporation. Therefore, in the following, a wide two-phase region containing 1:2 ordered 6H-Ba 2.8 Sr 0.2 ZnSb 2 O 9 and rock-salt ordered 3C-Ba 2 SrZnSb 2 O 9 was observed (0.3 ≤ x ≤ 1.0). In the final, the successive symmetry descending was established from cubic (Fm3̅m, 1.3 ≤ x ≤ 1.8) to tetragonal (I4/m, 2.0 ≤ x ≤ 2.4), and finally to monoclinic (I2/m, 2.6 ≤ x ≤ 3.0). Here we proved that the electronic configurations of B-site cations, with either empty, partially, or fully filled d-shell, would also affect the structure stabilization, through the orientation preference of the B-O covalent bonding. Our investigation gives a deeper understanding of the factors to the competitive formation of perovskite structures, facilitating the fine manipulation on their physical properties.

Di-μ-cyanido-1:2κC:N,2:3κN:C-hexa-cyanido-1κC,3κC-tetra-kis(1,10-phenanthroline)-1κN,N';2κN,N';3κN,N'-1,3-dicobalt(III)-2-iron(II) tetra-hydrate.

PubMed

Zhang, Ying; Yuan, Ai-Hua; Zhou, Hu; Guo, Ji-Xi; Liu, Lang

2009-08-08

The hydro-thermal reaction of CoCl(2)·6H(2)O, 1,10-phenanthroline (phen) and K(3)[Fe(CN)(6)] in deionized water yielded the title cyanide-bridged trinuclear cluster, [Co(2)Fe(CN)(8)(C(12)H(8)N(2))(4)]·4H(2)O or [{Co(III)(phen)(CN)(4)}(2){Fe(II)(phen)(2)}]·4H(2)O, which contains two Co(III) centers and one Fe(II) center linked by cyanide bridges. The combination of coordinative bonds, O-H⋯N and O-H⋯O hydrogen bonds and π-π stacking inter-actions [centroid-centroid distance = 3.630 (2) Å] results in the stabilization of a supra-molecular structure. All uncoordinated water molecules are disordered. Thermogravimetric analysis reveals that the title complex loses the four crystal water mol-ecules at about 333 K, then the anhydrous phase loses no further mass up to about 573 K, above which decomposition occurs.

Software Engineering Principles.

DTIC Science & Technology

1980-07-01

IC’ a It, It, Io It, It, o H 10 ~ Iro I0 E10 10 1 1 0 I 11. 1. 1. 10 1 0 1 0 1 c6 of a" I a f C f I 1 11 1 16 D , O f o 4 o I c1 w t I A, t I m 1 1 ca ...V. 4 4 4 I lbl. b 1 0 40 4 0 1 4 43c 4 40 ’ 10 40 4 I 10 4 4 1 4 4 40 Ic 1 011 1 If 0 . in44 3 4 4 3 4 4 I Io3 .4 4i I InI I I I 4 3 I CA I 4 I 4 3 I4...I 60 60 10 601 60. 6I I0 60 1~ 1 W 1 W 601 I3 Er- 6I 614 664;n3 6 W l. 60 l. 6 1 3 6 64 lb 46 lb l lb 6 M it I CA 0 6 lb. lbaa 1 0 r5 g m I . n lb lm

Solid-State Synthesis and Structure of the Enigmatic Ammonium Octaborate: (NH4)2[B7O9(OH)5]·3/4B(OH)3·5/4H2O.

PubMed

Neiner, Doinita; Sevryugina, Yulia V; Schubert, David M

2016-09-06

The compound known since the 19th century as ammonium octaborate was structurally characterized revealing the ammonium salt of the ribbon isomer of the heptaborate anion, [B7O9(OH)5](2-), with boric acid and water molecules. Of composition (NH4)2B7.75O12.63·4.88H2O, it approximates the classical ammonium octaborate composition (NH4)2B8O13·6H2O and has the structural formula {(NH4)2[B7O9(OH)5]}4·3B(OH)3·5H2O. It spontaneously forms at room temperature in solid-state mixtures of ammonium tetraborate and ammonium pentaborate. It crystallizes in the monoclinic space group P21/c with a = 11.4137(2) Å, b = 11.8877(2) Å, c = 23.4459(3) Å, β = 90.092(1)°, V = 3181.19(8) Å(3), and Z = 2 and contains well-ordered ammonium cations and [B7O9(OH)5](2-) anions and disordered B(OH)3 and H2O molecules linked by extensive H bonding. Expeditious solid-state formation of the heptaborate anion under ambient conditions has important implications for development of practical syntheses of industrially useful borates.

Fate of Shiga toxin-producing O157:H7 and non-O157:H7 Escherichia coli cells within refrigerated, frozen, or frozen then thawed ground beef patties cooked on a commercial open-flame gas or a clamshell electric grill.

PubMed

Luchansky, John B; Porto-Fett, Anna C S; Shoyer, Bradley A; Phillips, John; Chen, Vivian; Eblen, Denise R; Cook, L Victor; Mohr, Tim B; Esteban, Emilio; Bauer, Nathan

2013-09-01

Both high-fat and low-fat ground beef (percent lean:fat = ca. 70:30 and 93:7, respectively) were inoculated with a 6-strain cocktail of non-O157:H7 Shiga toxin-producing Escherichia coli (STEC) or a five-strain cocktail of E. coli O157:H7 (ca. 7.0 log CFU/g). Patties were pressed (ca. 2.54 cm thick, ca. 300 g each) and then refrigerated (4°C, 18 to 24 h), or frozen (-18°C, 3 weeks), or frozen (-18°C, 3 weeks) and then thawed (4°C for 18 h or 21°C for 10 h) before being cooked on commercial gas or electric grills to internal temperatures of 60 to 76.6°C. For E. coli O157:H7, regardless of grill type or fat level, cooking refrigerated patties to 71.1 or 76.6°C decreased E. coli O157:H7 numbers from an initial level of ca. 7.0 log CFU/g to a final level of ≤1.0 log CFU/g, whereas decreases to ca. 1.1 to 3.1 log CFU/g were observed when refrigerated patties were cooked to 60.0 or 65.5°C. For patties that were frozen or freeze-thawed and cooked to 71.1 or 76.6°C, E. coli O157:H7 numbers decreased to ca. 1.7 or ≤0.7 log CFU/g. Likewise, pathogen numbers decreased to ca. 0.7 to 3.7 log CFU/g in patties that were frozen or freeze-thawed and cooked to 60.0 or 65.5°C. For STEC, regardless of grill type or fat level, cooking refrigerated patties to 71.1 or 76.6°C decreased pathogen numbers from ca. 7.0 to ≤0.7 log CFU/g, whereas decreases to ca. 0.7 to 3.6 log CFU/g were observed when refrigerated patties were cooked to 60.0 or 65.5°C. For patties that were frozen or freeze-thawed and cooked to 71.1 or 76.6°C, STEC numbers decreased to a final level of ca. 1.5 to ≤0.7 log CFU/g. Likewise, pathogen numbers decreased from ca. 7.0 to ca. 0.8 to 4.3 log CFU/g in patties that were frozen or freeze-thawed and cooked to 60.0 or 65.5°C. Thus, cooking ground beef patties that were refrigerated, frozen, or freeze-thawed to internal temperatures of 71.1 and 76.6°C was effective for eliminating ca. 5.1 to 7.0 log CFU of E. coli O157:H7 and STEC per g.

Electron Transport Coefficients and Effective Ionization Coefficients in SF6-O2 and SF6-Air Mixtures Using Boltzmann Analysis

NASA Astrophysics Data System (ADS)

Wei, Linsheng; Xu, Min; Yuan, Dingkun; Zhang, Yafang; Hu, Zhaoji; Tan, Zhihong

2014-10-01

The electron drift velocity, electron energy distribution function (EEDF), density-normalized effective ionization coefficient and density-normalized longitudinal diffusion velocity are calculated in SF6-O2 and SF6-Air mixtures. The experimental results from a pulsed Townsend discharge are plotted for comparison with the numerical results. The reduced field strength varies from 40 Td to 500 Td (1 Townsend=10-17 V·cm2) and the SF6 concentration ranges from 10% to 100%. A Boltzmann equation associated with the two-term spherical harmonic expansion approximation is utilized to gain the swarm parameters in steady-state Townsend. Results show that the accuracy of the Boltzmann solution with a two-term expansion in calculating the electron drift velocity, electron energy distribution function, and density-normalized effective ionization coefficient is acceptable. The effective ionization coefficient presents a distinct relationship with the SF6 content in the mixtures. Moreover, the E/Ncr values in SF6-Air mixtures are higher than those in SF6-O2 mixtures and the calculated value E/Ncr in SF6-O2 and SF6-Air mixtures is lower than the measured value in SF6-N2. Parametric studies conducted on these parameters using the Boltzmann analysis offer substantial insight into the plasma physics, as well as a basis to explore the ozone generation process.

Interactive effects of MnO2, organic matter and pH on abiotic formation of N2O from hydroxylamine in artificial soil mixtures.

PubMed

Liu, Shurong; Berns, Anne E; Vereecken, Harry; Wu, Di; Brüggemann, Nicolas

2017-02-01

Abiotic conversion of the reactive nitrification intermediate hydroxylamine (NH 2 OH) to nitrous oxide (N 2 O) is a possible mechanism of N 2 O formation during nitrification. Previous research has demonstrated that manganese dioxide (MnO 2 ) and organic matter (OM) content of soil as well as soil pH are important control variables of N 2 O formation in the soil. But until now, their combined effect on abiotic N 2 O formation from NH 2 OH has not been quantified. Here, we present results from a full-factorial experiment with artificial soil mixtures at five different levels of pH, MnO 2 and OM, respectively, and quantified the interactive effects of the three variables on the NH 2 OH-to-N 2 O conversion ratio (R NH2OH-to-N2O ). Furthermore, the effect of OM quality on R NH2OH-to-N2O was determined by the addition of four different organic materials with different C/N ratios to the artificial soil mixtures. The experiments revealed a strong interactive effect of soil pH, MnO 2 and OM on R NH2OH-to-N2O . In general, increasing MnO 2 and decreasing pH increased R NH2OH-to-N2O , while increasing OM content was associated with a decrease in R NH2OH-to-N2O . Organic matter quality also affected R NH2OH-to-N2O . However, this effect was not a function of C/N ratio, but was rather related to differences in the dominating functional groups between the different organic materials.

Interactive effects of MnO2, organic matter and pH on abiotic formation of N2O from hydroxylamine in artificial soil mixtures

NASA Astrophysics Data System (ADS)

Liu, Shurong; Berns, Anne E.; Vereecken, Harry; Wu, Di; Brüggemann, Nicolas

2017-02-01

Abiotic conversion of the reactive nitrification intermediate hydroxylamine (NH2OH) to nitrous oxide (N2O) is a possible mechanism of N2O formation during nitrification. Previous research has demonstrated that manganese dioxide (MnO2) and organic matter (OM) content of soil as well as soil pH are important control variables of N2O formation in the soil. But until now, their combined effect on abiotic N2O formation from NH2OH has not been quantified. Here, we present results from a full-factorial experiment with artificial soil mixtures at five different levels of pH, MnO2 and OM, respectively, and quantified the interactive effects of the three variables on the NH2OH-to-N2O conversion ratio (RNH2OH-to-N2O). Furthermore, the effect of OM quality on RNH2OH-to-N2O was determined by the addition of four different organic materials with different C/N ratios to the artificial soil mixtures. The experiments revealed a strong interactive effect of soil pH, MnO2 and OM on RNH2OH-to-N2O. In general, increasing MnO2 and decreasing pH increased RNH2OH-to-N2O, while increasing OM content was associated with a decrease in RNH2OH-to-N2O. Organic matter quality also affected RNH2OH-to-N2O. However, this effect was not a function of C/N ratio, but was rather related to differences in the dominating functional groups between the different organic materials.

Zn-Fe-CNTs catalytic in situ generation of H2O2 for Fenton-like degradation of sulfamethoxazole.

PubMed

Liu, Yong; Fan, Qin; Wang, Jianlong

2018-01-15

A novel Fenton-like catalyst (Zn-Fe-CNTs) capable of converting O 2 to H 2 O 2 and further to OH was prepared through infiltration fusion method followed by chemical replacement in argon atmosphere. The catalyst was characterized by SEM, EDS, TEM, XRD and XPS. The reaction between Zn-Fe-CNTs and O 2 in aqueous solution could generate H 2 O 2 in situ, which was further transferred to OH. The Fenton-like degradation of sulfamethoxazole (SMX) using Zn-Fe-CNTs as catalyst was evaluated. The results indicated that Zn-Fe-CNTs had a coral porous structure with a BET area of 51.67m 2 /g, exhibiting excellent adsorption capacity for SMX, which enhanced its degradation. The particles of Zn 0 and Fe 0 /Fe 2 O 3 were observed on the surface of Zn-Fe-CNTs. The mixture of Zn 0 and CNTs could reduce O 2 into H 2 O 2 by micro-electrolysis and Fe 0 /Fe 2 O 3 could catalyze in-situ generation of H 2 O 2 to produce OH through Fenton-like process. When initial pH=1.5, T=25°C, O 2 flow rate=400mL/min, Zn-Fe-CNTs=0.6g/L, SMX=25mg/L and reaction time=10min, the removal efficiency of SMX and TOC was 100% and 51.3%, respectively. The intermediates were detected and the possible pathway of SMX degradation and the mechanism of Zn-Fe-CNTs/O 2 process were tentatively proposed. Copyright © 2017 Elsevier B.V. All rights reserved.

Decomposition of silane on tungsten or other materials

DOEpatents

Wiesmann, H.J.

This invention relates to hydrogenated amorphous silicon produced by thermally decomposing silane (SiH/sub 4/) or other gases comprising H and Si, from a W or foil heated to a temperature of about 1400 to 1600/sup 0/C, in a vacuum of about 10-/sup 6/ to 10-/sup 4/ torr. A gaseous mixture is formed of atomic hydrogen and atomic silicon. The gaseous mixture is deposited onto a substrate independent of and outside the source of thermal decomposition. Hydrogenated amorphous silicon is formed. The presence of an ammonia atmosphere in the vacuum chamber enhances the photoconductivity of the hydrogenated amorphous silicon film.

Solid-state {sup 27}Al and {sup 29}Si NMR characterization of hydrates formed in calcium aluminate-silica fume mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pena, P.; Rivas Mercury, J.M.; Aza, A.H. de

2008-08-15

Partially deuterated Ca{sub 3}Al{sub 2}(SiO{sub 4}){sub y}(OH){sub 12-4y}-Al(OH){sub 3} mixtures, prepared by hydration of Ca{sub 3}Al{sub 2}O{sub 6} (C{sub 3}A), Ca{sub 12}Al{sub 14}O{sub 33} (C{sub 12}A{sub 7}) and CaAl{sub 2}O{sub 4} (CA) phases in the presence of silica fume, have been characterized by {sup 29}Si and {sup 27}Al magic-angle spinning-nuclear magnetic resonance (MAS-NMR) spectroscopies. NMR spectroscopy was used to characterize anhydrous and fully hydrated samples. In hydrated compounds, Ca{sub 3}Al{sub 2}(OH){sub 12} and Al(OH){sub 3} phases were detected. From the quantitative analysis of {sup 27}Al NMR signals, the Al(OH){sub 3}/Ca{sub 3}Al{sub 2}(OH){sub 12} ratio was deduced. The incorporation of Simore » into the katoite structure, Ca{sub 3}Al{sub 2}(SiO{sub 4}){sub 3-x}(OH){sub 4x}, was followed by {sup 27}Al and {sup 29}Si NMR spectroscopies. Si/OH ratios were determined from the quantitative analysis of {sup 27}Al MAS-NMR components associated with Al(OH){sub 6} and Al(OSi)(OH){sub 5} environments. The {sup 29}Si NMR spectroscopy was also used to quantify the unreacted silica and amorphous calcium aluminosilicate hydrates formed, C-S-H and C-A-S-H for short. From {sup 29}Si NMR spectra, the amount of Si incorporated into different phases was estimated. Si and Al concentrations, deduced by NMR, transmission electron microscopy, energy dispersive spectrometry, and Rietveld analysis of both X-ray and neutron data, indicate that only a part of available Si is incorporated in katoite structures. - Graphical abstract: Transmission electron micrograph of CaAl{sub 2}O{sub 4}-microsilica mixture hydrated at 90 deg. C for 31 days showing a cubic Ca{sub 3}Al{sub 2.0{+-}}{sub 0.2}(SiO{sub 4}){sub 0.9{+-}}{sub 0.2}(OH){sub 1.8} crystal surrounded by unreacted amorphous silica spheres.« less

Fenton Oxidation Kinetics and Intermediates of Nonylphenol Ethoxylates

PubMed Central

Cui, Kai; Yi, Hao; Zhou, Zi-jian; Zhuo, Qiong-fang; Bing, Yong-xin; Guo, Qing-wei; Xu, Zhen-cheng

2014-01-01

Abstract Removal of nonylphenol ethoxylates (NPEOs) in aqueous solution by Fenton oxidation process was studied in a laboratory-scale batch reactor. Operating parameters, including initial pH temperature, hydrogen peroxide, and ferrous ion dosage, were thoroughly investigated. Maximum NPEOs reduction of 84% was achieved within 6 min, under an initial pH of 3.0, 25°C, an H2O2 dosage of 9.74×10−3 M, and a molar ratio of [H2O2]/[Fe2+] of 3. A modified pseudo-first-order kinetic model was found to well represent experimental results. Correlations of reaction rate constants and operational parameters were established based on experimental data. Results indicated that the Fenton oxidation rate and removal efficiency were more dependent on the dosage of H2O2 than Fe2+, and the apparent activation energy (ΔE) was 17.5 kJ/mol. High-performance liquid chromatography and gas chromatograph mass spectrometer analytical results indicated degradation of NPEOs obtained within the first 2 min stepwise occurred by ethoxyl (EO) unit shortening. Long-chain NPEOs mixture demonstrated a higher degradation rate than shorter-chain ones. Nonylphenol (NP), short-chain NPEOs, and NP carboxyethoxylates were identified as the primary intermediates, which were mostly further degraded. PMID:24868141

{Mo96La8} eggshell ring and self-assembly to {Mo132} Keplerate through Mo-blue intermediate, involved in UV-photolysis of [Mo7O24](6-)/carboxylic acid system at pH 4.

PubMed

Yamase, Toshihiro; Kumagai, Shun; Prokop, Petra V; Ishikawa, Eri; Tomsa, Adrian-Raul

2010-10-18

The prolonged UV-photolysis of aqueous solutions containing [Mo(7)O(24)](6-) and C(2)H(5)CO(2)H (as electron donor) at pH 3.9-4.1 generates the carboxylate-coordinated {Mo(132)} Keplerate (1a) isolated as a formamidinium/ammonium-mixed salt, [HC(NH(2))(2)](26)(NH(4))(28)[Mo(V)(60)Mo(VI)(72)O(372)(H(2)O)(48)(C(2)H(5)CO(2))(36)((i)C(3)H(7)CO(2))(6)]·16H(2)O (1), through the Mo-blue intermediate (2). The coordination of 2 to La(3+) gives rise to the formation of the chain structure of the C(2)-symmetric {Mo(96)La(8)} eggshell rings, formulated by H(22)[Mo(V)(20)Mo(VI)(76)O(301)(H(2)O)(29){La(H(2)O)(6)}(2)]{La(H(2)O)(5)}(6)]·54.5H(2)O (3). The eggshell-ring geometry results from the insertion of [Mo(VI)(2)O(7)(H(2)O)](2-) (spacer) into the equator outer ring of the wheel-shaped Mo-blue, and 10 {(Mo(VI))(Mo(VI)(5))} pentagonal subunits alternately above and below the equator outer ring are connected by eight La(3+) and two {Mo(VI)(2)} linkers within two inner rings. The neighboring eggshell rings are linked through two Mo-O-Mo bonds formed by dehydrative condensation between the {Mo(VI)(2)} linkers to result in the chain structure. Together with the results of the elemental analysis and IR, electronic absorption, (13)C NMR, and ESI-MS spectra for 2, the ring profile analysis of 3 let us identify 2 with a carbolylate-coordinated Mo-blue ring of high nuclearity. The Mo(VI)→Mo(V) photoreductive change of 2 to the 60-electron reduced Keplerate in the presence of C(2)H(5)CO(2)H involves both degradation of the outer ring and splitting of the binuclear linkers, which leads to the formation of [(Mo(VI))Mo(VI)(5)O(21)(H(2)O)(4)(carboxylate)](7-) pentagonal subunits and [Mo(V)(2)O(4)(carboxylate)](+)/[Mo(V)O(2)(carboxylate)(1/2)](0.5+)-mixed linkers for 1.

Electrical Conductivity of Cancrinite-Type Na8 - 2 x Ca x [Al6Si6O24][CO3] · 2H2O ( x ≤ 0.03) Crystals

NASA Astrophysics Data System (ADS)

Sorokin, N. I.

2018-05-01

The electrical conductivity of crystals of artificial cancrinite Na8 - 2 x Ca x [Al6Si6O24][CO3] · 2H2O ( x ≤ 0.03) has been studied in the temperature range of 498-604 K. These crystals were grown by hydrothermal synthesis on a seed in the Na2O-Al2O3-SiO2-H2O system ( t = 380-420°C, P = 3 × 107-9 × 107 Pa). The ionic conductivity of a single-crystal sample (sp. gr. P63), measured along the crystallographic axis c, is low: σ = 8 × 10-7 S/cm at 300°C. The electric transport activation energy is E a = 0.81 ± 0.05 eV. The relationship between the ionic conductivity and specific features of the atomic structure of cancrinites is discussed.

Thermal tolerance characteristics of non-O157 Shiga toxigenic strains of Escherichia coli (STEC) in a beef broth model system are similar to those of O157:H7 STEC.

PubMed

Vasan, Akhila; Leong, Wan Mei; Ingham, Steve C; Ingham, Barbara H

2013-07-01

The non-O157 Shiga toxigenic Escherichia coli (STEC) serogroups most commonly associated with illness are O26, O45, O103, O111, O121, and O145. In the United States, these serogroups are considered adulterants in raw nonintact beef. To begin to understand the behavior of these pathogens in meat systems, we compared the thermal tolerance of acid-adapted cells of non-O157 STEC and O157:H7 STEC in a beef-derived broth. D58°C-values were determined for at least three strains per serogroup, and D54.6°C-values and D63.6°C-values were determined for one strain per serogroup. Each strain was grown to stationary phase in brain heart infusion broth (BHIB; pH 7.0) and inoculated into prewarmed BHIB in a shaking water bath for thermotolerance experiments at 54.6, 58.0, or 63.6°C (three trials per strain). Samples were heated for up to 160 min at 54.6°C, 3 min at 58.0°C, or 45 s at 63.6°C, with periodic sampling followed by rapid cooling and plating on modified Levine's eosin methylene blue agar. For each strain and temperature, the log CFU per milliliter was plotted versus time, and D-values were determined. Across all strains, the least and most heat tolerant STEC serogroups at 58°C were O145 and O157, respectively. D58°C-values in BHIB ranged from 0.44 min for an O145 strain to 1.42 min for an O157:H7 strain. D58°C-values for O157 STEC strains were significantly higher than those for at least one strain in each of the non-O157 STEC serogroups (P < 0.05) except for serogroup O103. At 54.6°C, the most heat-resistant STEC strain belonged to serogroup O103 and was significantly more heat tolerant than the O157:H7 strains (P < 0.05). Grouping the strains, there were no significant differences in heat tolerance between O157 and non-O157 STEC at 63.6°C (P ≥ 0.05). The z-values for non-O157 STEC strains were comparable to those for O157:H7 STEC strains (P ≥ 0.05), ranging from 4.10 to 5.21°C. These results suggest that thermal processing interventions that target destruction of E. coli O157:H7 may have adequate lethality against non-O157 STEC.

Nano-emulsions as vehicles for topical delivery of forskolin.

PubMed

Miastkowska, Małgorzata; Sikora, Elżbieta; Lasoń, Elwira; Garcia-Celma, Maria Jose; Escribano-Ferrer, Elvira; Solans, Conxita; Llinas, Meritxell

2017-01-01

Two O/W forskolin-loaded nano-emulsions (0.075% wt.) based on medium chain triglycerides (MCT) and stabilized by a nonionic surfactant (Polysorbate 80 or Polysorbate 40) were studied as forskolin delivery systems. The nano-emulsions were prepared by the PIC method. The mean droplet size of the nano-emulsions with Polysorbate 80 and Polysorbate 40 with oil/surfactant (O/S) ratios of 20/80 and 80% water concentration, measured by Dynamic Light Scattering (DLS), was of 118 nm and 111 nm, respectively. Stability of the formulations, as assessed by light backscattering for 24 h, showed that both nano-emulsions were stable at 25°C. Studies of forskolin in vitro skin permeation from the nano-emulsions and from a triglyceride solution were carried out at 32°C, using Franz-type diffusion cells. A mixture of PBS/ethanol (60/40 v/v) was used as a receptor solution. The highest flux and permeability coefficient was obtained for the system stabilized with Polysorbate 80 (6.91±0.75 µg · cm -2 ·h -1 and 9.21 · 10 -3 ±1.00 · 10 -3 cm · h -1 , respectively) but no significant differences were observed with the flux and permeability coefficient value of forskolin dissolved in oil. The obtained results showed that the nano-emulsions developed in this study could be used as effective carriers for topical administration of forskolin.

Tautomeric properties, conformations and structure of N-(2-hydroxy-5-chlorophenyl) salicylaldimine

NASA Astrophysics Data System (ADS)

Elmali, A.; Kabak, M.; Kavlakoglu, E.; Elerman, Y.; Durlu, T. N.

1999-11-01

The crystal structure of N-(2-hydroxy-5-chlorophenyl) salicylaldimine (C 13H 10NO 2Cl) was determined by X-ray analysis. It crystallizes orthorhombic space group P2 12 12 1 with a=12.967(2) Å, b=14.438(3) Å, c=6.231(3) Å, V=1166.5(6) Å 3, Z=4, Dc=1.41 g cm -3 and μ(MoK α)=0.315 mm -1. The title compound is thermochromic and the molecule is nearly planar. Both tautomeric forms (keto and enol forms in 68(3) and 32(3)%, respectively) are present in the solid state. The molecules contain strong intramolecular hydrogen bonds, N1-H1⋯O1/O2 (2.515(1) and 2.581(2) Å) for the keto form and O1-H01⋯N1 for the enol one. There is also strong intermolecular O2-H⋯O1 hydrogen bonding (2.599(2) Å) between neighbouring molecules. Minimum energy conformations AM1 were calculated as a function of the three torsion angles, θ1(N1-C7-C6-C5), θ2(C8-N1-C7-C6) and θ3(C9-C8-N1-C7), varied every 10°. Although the molecule is nearly planar, the AM1 optimized geometry of the title compound is not planar. The non-planar conformation of the title compound corresponding to the optimized X-ray structure is the most stable conformation in all calculations.

Synthesis, structure, antitumor activity of novel pharmaceutical co-crystals based on bispyridyl-substituted α, β-unsaturated ketones with gallic acid

NASA Astrophysics Data System (ADS)

Liu, Lian-Dong; Liu, Shu-Lian; Liu, Zhi-Xian; Hou, Gui-Ge

2016-05-01

Three novel pharmaceutical co-crystals, (A)·(gallic acid) (1), (B)·(gallic acid) (2), and (C)·(gallic acid) (3) were generated based on 2,6-bis((pyridin-4-yl)methylene)cyclohexanone (A), N-methyl-3,5-bis((pyridin-3-yl)methylene)-4-piperidone (B), N-methyl-3,5-bis((pyridin-4-yl)methylene)-4-piperidone (C) with gallic acid, respectively. They are characterized by elemental analysis, FTIR spectroscopy, 1H NMR and single-crystal X-ray diffraction. Structural analysis reveals that two pharmaceutical ingredients link each other into H-bonding-driven 3D network in 1, 2, or 2D plane in 3. In addition, their antitumor activities against human neoplastic cell lines A549, SGC-7901, MCF-7, OVCA-433, HePG2 and cytotoxicity for HUVEC cell lines by CCK-8 method were evaluated primarily. Compared with gallic acid and free A, B and C, their antitumor activities have improved distinctly, while cytotoxicities have reduced markedly, especially for co-crystal 1. This is mainly because of the synergistic effect between pharmaceutical ingredients A, B, and C and gallic acid.

Phthalazin-1(2H)-one–picric acid (1/1)

PubMed Central

Yathirajan, H. S.; Narayana, B.; Swamy, M. T.; Sarojini, B. K.; Bolte, Michael

2008-01-01

The geometric parameters of the title compound, C8H6N2O·C6H3N3O7, are in the usual ranges. The three nitro groups are almost coplanar with the aromatic picrate ring [dihedral angles 10.2 (2)°, 7.62 (16) and 8.08 (17)°]. The mol­ecular conformation of the picric acid is stabilized by an intra­molecular O—H⋯O hydrogen bond. The phthalazin-1(2H)-one mol­ecules are connected via N—H⋯O hydrogen bonds, forming centrosymmetric dimers. PMID:21200682

Synthesis and structure determination of La{sub 8}Ti{sub 10}S{sub 24}O{sub 4}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cario, L.; Deudon, C.; Meerschaut, A.

1998-02-15

The new compound La{sub 8}Ti{sub 10}S{sub 24}O{sub 4} has been prepared from a mixture of La{sub 2}Ti{sub 2}O{sub 7} and La{sub 2}O{sub 3} (in a 5:1 ratio) heated at 1,200 C under a H{sub 2}S gas flow. This new quaternary phase was obtained due to an incomplete sulfidizing process. Single-crystal X-ray diffraction studies show that La{sub 8}Ti{sub 10}S{sub 24}O{sub 4} crystallizes in space group P4/mmm, with Z = 1, in a cell of dimensions a = b = 10.421 {angstrom} and c = 8.384 {angstrom}. Least-squares refinement converged to values of R - 0.045 and R{sub w} = 0.048. Themore » structure can be viewed as a stacking of two types of layers along the {rvec c} axis. These layers are built up from infinite rutile-like chains (Ti octahedra) that cross perpendicularly. La atoms, in a tricapped prismatic coordination, are located in tunnels that develop parallel to the {rvec c} direction.« less

Synthesis, characterization, electrochemical investigation and antioxidant activities of a new hybrid cyclohexaphosphate: Cu1.5Li(C2H10N2)P6O18·7H2O

NASA Astrophysics Data System (ADS)

Sleymi, Samira; Lahbib, Karima; Rahmouni, Nihed; Rzaigui, Mohamed; Besbes-Hentati, Salma; Abid, Sonia

2017-09-01

A new organic-inorganic hybrid transition metal phosphate, Cu1.5Li(C2H10N2)P6O18·7H2O, has been prepared and characterized by X-ray diffraction, spectroscopy (infrared, Raman, diffuse reflectance and UV-Vis) and thermal analysis (TG). In addition, its electrochemical behaviors, as well as its antioxidant and antibacterial activities, have been investigated. Its structure is built up by the alternate linkages between copper and phosphate polyhedra, forming puckered layers with intersecting 12-membered rings, in which the ethylenediammonium cations reside. This compound is the first framework structure constructed from cyclohexaphosphates and three distinct copper cations. Cyclic voltammetry study in an acetonitrile solution reveals the facile anodic oxidation of its organic part on a platinum disk and a progressive growing of a thin film, though the repetitive cycling of potential. The title compound was tested for its in vitro antioxidant activities by 1,1-diphenyl-2-picrylhydrazyl (DPPH), 2,2‧-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS), Ferrous chelating ability (FIC) and Ferric Reducing Power (FRP) methods. The antioxidant activity of Cu1.5Li(C2H10N2)P6O18·7H2O was analyzed simultaneously with its antibacterial capacity against Escherichia coli, Salmonella typhimurium, Staphylococus aureus, Enterococcus feacium, Streptococcus agalactiae and Candida albicans. The tested compound showed significant antioxidant activities with low antibacterial properties.

Crystal structures of two 6-(2-hy-droxy-benzo-yl)-5H-thia-zolo[3,2-a]pyrimidin-5-ones.

PubMed

Gomes, Ligia R; Low, John Nicolson; Cagide, Fernando; Borges, Fernanda

2015-07-01

The title compounds, 6-(2-hy-droxy-benz-yl)-5H-thia-zolo[3,2-a]pyrimidin-5-one, C13H8N2O3S, (1), and 6-(2-hy-droxy-benz-yl)-3-methyl-5H-thia-zolo[3,2-a]pyrimidin-5-one, C14H10N2O3S, (2), were synthesized when a chromone-3-carb-oxy-lic acid, activated with (benzotriazol-1-yl-oxy)tripyrrolidinyl-phospho-nium hexa-fluorido-phosphate (PyBOP), was reacted with a primary heteromamine. Instead of the expected amidation, the unusual title thia-zolo-pyrimidine-5-one derivatives were obtained serendipitously and a mechanism of formation is proposed. Both compounds present an intra-molecular O-H⋯O hydrogen bond, which generates an S(6) ring. The dihedral angles between the heterocyclic moiety and the 2-hydroxybenzoyl ring are 55.22 (5) and 46.83 (6)° for (1) and (2), respectively. In the crystals, the mol-ecules are linked by weak C-H⋯O hydrogen bonds and π-π stacking inter-actions.

Production and reactivity of the hydroxyl radical in homogeneous high pressure plasmas of atmospheric gases containing traces of light olefins

NASA Astrophysics Data System (ADS)

Magne, L.; Pasquiers, S.; Blin-Simiand, N.; Postel, C.

2007-05-01

A photo-triggered discharge has been used to study the production kinetic mechanisms and the reactivity of the hydroxyl radical in a N2/O2 mixture (5% oxygen) containing ethane or ethene for hydrocarbon concentration values in the range 1000-5000 ppm, at 460 mbar total pressure. The discharge (current pulse duration of 60 ns) has allowed the generation of a transient homogeneous non-equilibrium plasma, and the time evolution of the OH density has been measured (relative value) in the afterglow (up to 200 µs) by laser induced fluorescence (LIF). Experimental results have been explained using predictions of a self-consistent 0D discharge and plasma reactivity modelling, and reduced kinetic schemes for OH have been validated. It has been shown that recombination of H- and O-atoms, as well as reaction of O with the hydroperoxy radical HO2, plays a very important role in the production of OH radicals in the mixture with ethane. H is a key species for production of OH and HO2 radicals. As for ethane, O, H and HO2 are key species for the production of OH in the case of ethene, but carbonated radicals, following the partial oxidation of the hydrocarbon molecule by O, also play a non-negligible role. The rate constant for O- and H-atom recombination has been estimated to be 3 × 10-30 cm6 s-1 at near ambient temperature, consistent with LIF measurements on OH for both mixtures with ethane and ethene.

Activation of C-O and C-C bonds and formation of novel HAlOH-ether complexes: an EPR study of the reaction of ground-state Al atoms with methylethyl ether and diethyl ether.

PubMed

Brunet, François D; Feola, Julie C; Joly, Helen A

2012-03-15

Reaction mixtures, containing Al atoms and methylethyl ether (MEE) or diethyl ether (DEE) in an adamantane matrix, were prepared with the aid of a metal-atom reactor known as a rotating cryostat. The EPR spectra of the resulting products were recorded from 77-260 K, at 10 K intervals. Al atoms were found to insert into methyl-O, ethyl-O, and C-C bonds to form CH(3)AlOCH(2)CH(3), CH(3)OAlCH(2)CH(3), and CH(3)OCH(2)AlCH(3), respectively, in the case of MEE while DEE produced CH(3)CH(2)AlOCH(2)CH(3) and CH(3)AlCH(2)OCH(2)CH(3), respectively. From the intensity of the transition lines attributed to the Al atom C-O insertion products of MEE, insertion into the methyl-O bond is preferred. The Al hyperfine interaction (hfi) extracted from the EPR spectra of the C-O insertion products was greater than that of the C-C insertion products, that is, 5.4% greater for the DEE system and 7% greater for the MEE system. The increase in Al hfi is thought to arise from the increased electron-withdrawing ability of the substituents bonded to Al. Besides HAlOH, resulting from the reaction of Al atoms with adventitious water, novel mixed HAlOH:MEE and HAlOH:DEE complexes were identified with the aid of isotopic studies involving H(2)(17)O and D(2)O. The Al and H hfi of HAlOH were found to decrease upon complex formation. These findings are consistent with the nuclear hfi calculated using a density functional theory (DFT) method with close agreement between theory and experiment occurring at the B3LYP level using a 6-311+G(2df,p) basis set.

Overproduction of cellulase by Trichoderma reesei RUT C30 through batch-feeding of synthesized low-cost sugar mixture.

PubMed

Li, Yonghao; Liu, Chenguang; Bai, Fengwu; Zhao, Xinqing

2016-09-01

Cellulase is a prerequisite for the bioconversion of lignocellulosic biomass, but its high cost presents the biggest challenge. In this article, low-cost mixture was produced from glucose through the transglycosylation reaction catalyzed by β-glucosidase for cellulase overproduction by Trichodema reesei RUT C30. As a result, cellulase titer of 90.3FPU/mL, which was more than 10 folds of that achieved with lactose as inducer, was achieved at 144h. Meanwhile, cellulase productivity was drastically increased to 627.1FPU/L/h, at least 3-5 folds higher than previously reported by the fungal species. The crude enzyme was further tested by hydrolyzing NaOH-pretreated corn stover with 15% solid loading, and 96.6g/L glucose was released with 92.6% sugar yield at 96h and 44.8g/L ethanol was obtained. Copyright © 2016 Elsevier Ltd. All rights reserved.

A halogenophilic pathway in the reactions of transition metal carbonyl anions with [(η⁶-iodobenzene)Cr(CO)₃].

PubMed

Sazonov, Petr K; Ivushkin, Vasiliy A; Khrustalev, Victor N; Kolotyrkina, Natal'ya G; Beletskaya, Irina P

2014-09-21

The paper provides the first example of formal nucleophilic substitution by the halogenophilic pathway in Cr(CO)3 complexes of haloarenes with metal carbonyl anions. All metal carbonyl anions examined attack [(η(6)-iodobenzene)Cr(CO)3] at halogen, which is shown by aryl carbanion scavenging with t-BuOH. The reaction with K[CpFe(CO)2] gives only the dehalogenated arene, but the reaction with K[Cp*Fe(CO)2] (Cp* = η(5)-C5Me5) results in nucleophilic substitution to give [(η(6)-C6H5FeCp*(CO)2)Cr(CO)3]. Reaction with Na[Re(CO)5] quantitatively gives the iodo(acyl)rhenate anion Na[(η(6)-C6H5C(O)ReI(CO)4)Cr(CO)3] and in the case of K[Mn(CO)5] a mixture of σ-aryl complexes [(η(6)-C6H5Mn(CO)5)Cr(CO)3] and K[(η(6)-C6H5Mn(CO)4I)Cr(CO)3]. An analogous rhenium complex Na[(η(6)-C6H5Re(CO)4I)Cr(CO)3] is formed from the initial iodo(acyl)rhenate upon prolonged standing at 20 °C, and its structure (in the form of [NEt4](+) salt) is established by X-ray diffraction analysis. The reaction of [(η(6)-chlorobenzene)Cr(CO)3] with K[CpFe(CO)2], in contrast, proceeds by the common S(N)2Ar mechanism.

X-Ray diffraction and mu-Raman investigation of the monoclinic-orthorhombic phase transition in Th(1-x)U(x)(C(2)O(4))(2).2H(2)O solid solutions.

PubMed

Clavier, Nicolas; Hingant, Nina; Rivenet, Murielle; Obbade, Saïd; Dacheux, Nicolas; Barré, Nicole; Abraham, Francis

2010-02-15

A complete Th(1-x)U(x)(C(2)O(4))(2).2H(2)O solid solution was prepared by mild hydrothermal synthesis from a mixture of hydrochloric solutions containing cations and oxalic acid. The crystal structure has been solved from twinned single crystals for x = 0, 0.5, and 1 with monoclinic symmetry, space group C2/c, leading to unit cell parameters of a approximately 10.5 A, b approximately 8.5 A, and c approximately 9.6 A. The crystal structure consists of a two-dimensional arrangement of actinide centers connected through bis-bidentate oxalate ions forming squares. The actinide metal is coordinated by eight oxygen atoms from four oxalate entities and two water oxygen atoms forming a bicapped square antiprism. The connection between the layers is assumed by hydrogen bonds between the water molecules and the oxygen of oxalate of an adjacent layer. Under these conditions, the unit cell contains two independent oxalate ions. From high-temperature mu-Raman and X-ray diffraction studies, the compounds were found to undergo a transition to an orthorhombic form (space group Ccca). The major differences in the structural arrangement concern the symmetry of uranium, which decreases from C2 to D2, leading to a unique oxalate group. Consequently, the nu(s)(C-O) double band observed in the Raman spectra recorded at room temperature turned into a singlet. This transformation was then used to make the phase transition temperature more precise as a function of the uranium content of the sample.

Thermogravimetric and calorimetric characteristics during co-pyrolysis of municipal solid waste components.

PubMed

Ansah, Emmanuel; Wang, Lijun; Shahbazi, Abolghasem

2016-10-01

The thermogravimetric and calorimetric characteristics during pyrolysis of wood, paper, textile and polyethylene terephthalate (PET) plastic in municipal solid wastes (MSW), and co-pyrolysis of biomass-derived and plastic components with and without torrefaction were investigated. The active pyrolysis of the PET plastic occurred at a much higher temperature range between 360°C and 480°C than 220-380°C for the biomass derived components. The plastic pyrolyzed at a heating rate of 10°C/min had the highest maximum weight loss rate of 18.5wt%/min occurred at 420°C, followed by 10.8wt%/min at 340°C for both paper and textile, and 9.9wt%/min at 360°C for wood. At the end of the active pyrolysis stage, the final mass of paper, wood, textile and PET was 28.77%, 26.78%, 21.62% and 18.31%, respectively. During pyrolysis of individual MSW components at 500°C, the wood required the least amount of heat at 665.2J/g, compared to 2483.2J/g for textile, 2059.4J/g for paper and 2256.1J/g for PET plastic. The PET plastic had much higher activation energy of 181.86kJ/mol, compared to 41.47kJ/mol for wood, 50.01kJ/mol for paper and 36.65kJ/mol for textile during pyrolysis at a heating rate of 10°C/min. H2O and H2 peaks were observed on the MS curves for the pyrolysis of three biomass-derived materials but there was no obvious H2O and H2 peaks on the MS curves of PET plastic. There was a significant interaction between biomass and PET plastic during co-pyrolysis if the biomass fraction was dominant. The amount of heat required for the co-pyrolysis of the biomass and plastic mixture increased with the increase of plastic mass fraction in the mixture. Torrefaction at a proper temperature and time could improve the grindability of PET plastic. The increase of torrefaction temperature and time did not affect the temperature where the maximum pyrolytic rates occurred for both biomass and plastic but decreased the maximum pyrolysis rate of biomass and increased the maximum pyrolysis rate of PET plastic. The amount of heat for the pyrolysis of biomass and PET mixture co-torrefied at 280°C for 30min was 4365J/g at 500°C, compared to 1138J/g for the pyrolysis of raw 50% wood and 50% PET mixture at the same condition. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pincer phosphine complexes of ruthenium: formation of Ru(P-O-P)(PPh3)HCl (P-O-P = xantphos, DPEphos, (Ph2PCH2CH2)2O) and Ru(dppf)(PPh3)HCl and characterization of cationic dioxygen, dihydrogen, dinitrogen, and arene coordinated phosphine products.

PubMed

Ledger, Araminta E W; Moreno, Aitor; Ellul, Charles E; Mahon, Mary F; Pregosin, Paul S; Whittlesey, Michael K; Williams, Jonathan M J

2010-08-16

Treatment of Ru(PPh(3))(3)HCl with the pincer phosphines 9,9-dimethyl-4,5-bis(diphenylphosphino)xanthene (xantphos), bis(2-diphenylphosphinophenyl)ether (DPEphos), or (Ph(2)PCH(2)CH(2))(2)O affords Ru(P-O-P)(PPh(3))HCl (xantphos, 1a; DPEphos, 1b; (Ph(2)PCH(2)CH(2))(2)O, 1c). The X-ray crystal structures of 1a-c show that all three P-O-P ligands coordinate in a tridentate manner through phosphorus and oxygen. Abstraction of the chloride ligand from 1a-c by NaBAr(4)(F) (BAr(4)(F) = B(3,5-C(6)H(3)(CF(3))(2))(4)) gives the cationic aqua complexes [Ru(P-O-P)(PPh(3))(H(2)O)H]BAr(4)(F) (3a-c). Removal of chloride from 1a by AgOTf yields Ru(xantphos)(PPh(3))H(OTf) (2a), which reacts with water to form [Ru(xantphos)(PPh(3))(H(2)O)H](OTf). The aqua complexes 3a-b react with O(2) to generate [Ru(xantphos)(PPh(3))(eta(2)-O(2))H]BAr(4)(F) (5a) and [Ru(DPEphos)(PPh(3))(eta(2)-O(2))H]BAr(4)(F) (5b). Addition of H(2) or N(2) to 3a-c yields the thermally unstable dihydrogen and dinitrogen species [Ru(P-O-P)(PPh(3))(eta(2)-H(2))H]BAr(4)(F) (6a-c) and [Ru(P-O-P)(PPh(3))(N(2))H]BAr(4)(F) (7a-c), which have been characterized by multinuclear NMR spectroscopy at low temperature. Ru(PPh(3))(3)HCl reacts with 1,1'-bis(diphenylphosphino)ferrocene (dppf) to give the 16-electron complex Ru(dppf)(PPh(3))HCl (1d), which upon treatment with NaBAr(4)(F), affords [Ru(dppf){(eta(6)-C(6)H(5))PPh(2)}H]BAr(4)(F) (8), in which the PPh(3) ligand binds eta(6) through one of the PPh(3) phenyl rings. Reaction of 8 with CO or PMe(3) at elevated temperatures yields the 18-electron products [Ru(dppf)(PPh(3))(CO)(2)H]BAr(F)(4) (9) and [Ru(PMe(3))(5)H]BAr(4)(F) (10).

Transitions from functionalization to fragmentation reactions of laboratory secondary organic aerosol (SOA) generated from the OH oxidation of alkane precursors.

PubMed

Lambe, Andrew T; Onasch, Timothy B; Croasdale, David R; Wright, Justin P; Martin, Alexander T; Franklin, Jonathan P; Massoli, Paola; Kroll, Jesse H; Canagaratna, Manjula R; Brune, William H; Worsnop, Douglas R; Davidovits, Paul

2012-05-15

Functionalization (oxygen addition) and fragmentation (carbon loss) reactions governing secondary organic aerosol (SOA) formation from the OH oxidation of alkane precursors were studied in a flow reactor in the absence of NO(x). SOA precursors were n-decane (n-C10), n-pentadecane (n-C15), n-heptadecane (n-C17), tricyclo[5.2.1.0(2,6)]decane (JP-10), and vapors of diesel fuel and Southern Louisiana crude oil. Aerosol mass spectra were measured with a high-resolution time-of-flight aerosol mass spectrometer, from which normalized SOA yields, hydrogen-to-carbon (H/C) and oxygen-to-carbon (O/C) ratios, and C(x)H(y)+, C(x)H(y)O+, and C(x)H(y)O(2)+ ion abundances were extracted as a function of OH exposure. Normalized SOA yield curves exhibited an increase followed by a decrease as a function of OH exposure, with maximum yields at O/C ratios ranging from 0.29 to 0.74. The decrease in SOA yield correlates with an increase in oxygen content and decrease in carbon content, consistent with transitions from functionalization to fragmentation. For a subset of alkane precursors (n-C10, n-C15, and JP-10), maximum SOA yields were estimated to be 0.39, 0.69, and 1.1. In addition, maximum SOA yields correspond with a maximum in the C(x)H(y)O+ relative abundance. Measured correlations between OH exposure, O/C ratio, and H/C ratio may enable identification of alkane precursor contributions to ambient SOA.

Fabrication of piezoelectric ceramic fibers by extrusion of Pb(Zr, Ti)O3 powder and Pb(Zr, Ti)O3 sol mixture

NASA Astrophysics Data System (ADS)

Qiu, Jinhao; Tani, Junji; Kobayashi, Yoshimasa; Um, Tae Young; Takahashi, Hirofumi

2003-06-01

In this study, Pb(Zr, Ti)O3 (PZT) piezoelectric ceramic fibers were fabricated by extrusion from a mixture of PZT powder and PZT sol. The added PZT sol in this study played the role of a binder; the sol changed into crystalline PZT during sintering, and removal of additives before sintering was not required. To obtain the required PZT fibers, the sol viscosity adjustment condition, the mixture ratio of powder and sol for fiber extrusion, and the sintering condition for obtaining polycrystalline fibers were investigated. The PZT precursor solution was synthesized from lead acetate trihydrate, zirconium n-propoxide, and titanium isopropoxide by reflux at 120 °C for 3 h with 2-methoxyethanol. The appropriate adjustment of the spinnable sol was achieved by the addition of acetic acid to suppress the hydrolysis reaction and by curing the sol at 80 °C to promote the condensation of the sol. Green fibers with diameters of about 300µm were successfully extruded from the mixture of PZT powder and sol (powder:sol = 5- 8:1, molar ratio). The extruded fibers, sintered at 1200 °C, had a microstructure with 2- 6µm grains and had no pores or cracks. From the results of displacement behavior measurements, the PZT fibers fabricated by firing at 1200 °C in this study were considered to have the desired piezoelectric properties.

Ruthenium-catalyzed metathesis reactions of ortho- and meta-dialkenyl-carboranes: efficient ring-closing and acyclic diene polymerization reactions.

PubMed

Guron, Marta; Wei, Xiaolan; Carroll, Patrick J; Sneddon, Larry G

2010-07-05

The ruthenium-catalyzed metathesis reactions of dialkenyl-substituted ortho- and meta-carboranes provide excellent routes to both cyclic-substituted o-carboranes and new types of main-chain m-carborane polymers. The adjacent positions of the two olefins in the 1,2-(alkenyl)(2)-o-carboranes strongly favor the formation of ring-closed (RCM) products with the reactions of 1,2-(CH(2)=CHCH(2))(2)-1,2-C(2)B(10)H(10) (1), 1,2-(CH(2)=CH(CH(2))(3)CH(2))(2)-1,2-C(2)B(10)H(10) (2), 1,2-(CH(2)=CHSiMe(2))(2)-1,2-C(2)B(10)H(10) (3), 1,2-(CH(2)=CHCH(2)SiMe(2))(2)-1,2-C(2)B(10)H(10) (4), and 1,2-[CH(2)=CH(CH(2))(4)SiMe(2)](2)-1,2-C(2)B(10)H(10) (5) affording 1,2-(-CH(2)CH=CHCH(2)-)-C(2)B(10)H(10) (10), 1,2-[-CH(2)(CH(2))(3)CH=CH(CH(2))(3)CH(2)-]-1,2-C(2)B(10)H(10) (11), 1,2-[-SiMe(2)CH=CHSiMe(2)-]-1,2-C(2)B(10)H(10) (12), 1,2-[-SiMe(2)CH(2)CH=CHCH(2)SMe(2)-]-C(2)B(10)H(10) (13), and 1,2-[-SiMe(2)(CH(2))(4)CH=CH(CH(2))(4)SiMe(2)-]-C(2)B(10)H(10) (14), respectively, in 72-97% yields. On the other hand, the reaction of 1,2-(CH(2)-CHCH(2)OC(=O))(2)-1,2-C(2)B(10)H(10) (6) gave cyclo-[1,2-(1',8'-C(=O)OCH(2)CH=CHCH(2)OC(=O))-1,2-C(2)B(10)H(10)](2) (15a) and polymer 15b resulting from intermolecular metathesis reactions. The nonadjacent positions of the alkenyl groups in the 1,7-(alkenyl)(2)-m-carboranes, 1,7-(CH(2)=CHCH(2))(2)-1,7-C(2)B(10)H(10) (7), 1,7-(CH(2)=CH(CH(2))(3)CH(2))(2)-1,7-C(2)B(10)H(10) (8), and 1,7-(CH(2)=CHCH(2)SiMe(2))(2)-1,7-C(2)B(10)H(10) (9), disfavor the formation of RCM products, and in these cases, acyclic diene metathesis polymerizations (ADMET) produced new types of main chain m-carborane polymers. The structures of 3, 9, 11, 12, 13, and 15a were crystallographically confirmed.

Detections of Long Carbon Chains CH_{3}CCCCH, C_{6}H, LINEAR-C_{6}H_{2} and C_{7}H in the Low-Mass Star Forming Region L1527

NASA Astrophysics Data System (ADS)

Araki, Mitsunori; Takano, Shuro; Sakai, Nami; Yamamoto, Satoshi; Oyama, Takahiro; Kuze, Nobuhiko; Tsukiyama, Koichi

2017-06-01

Carbon chains in the warm carbon chain chemistry (WCCC) region has been searched in the 42-44 GHz region by using Green Bank 100 m telescope. Long carbon chains C_{7}H, C_{6}H, CH_{3}CCCCH, and linear-C_{6}H_{2} and cyclic species C_{3}H and C_{3}H_{2}O have been detected in the low-mass star forming region L1527, performing the WCCC. C_{7}H was detected for the first time in molecular clouds. The column density of C_{7}H is derived to be 6.2 × 10^{10} cm^{-2} by using the detected J = 24.5-23.5 and 25.5-24.5 rotational lines. The ^{2}Π_{1/2} electronic state of C_{6}H, locating 21.6 K above the ^{2}Π_{3/2} electronic ground state, and the K_a = 0 line of the para species of linear-C_{6}H_{2} were also detected firstly in molecular clouds. The column densities of the ^{2}Π_{1/2} and ^{2}Π_{3/2} states of C_{6}H in L1527 were derived to be 1.6 × 10^{11} and 1.1 × 10^{12} cm^{-2}, respectively. The total column density of linear-C_{6}H_{2} is obtained to be 1.86 × 10^{11} cm^{-2}. While the abundance ratios of carbon chains in between L1527 and the starless dark cloud Taurus Molecular Cloud-1 Cyanopolyyne Peak (TMC-1 CP) have a trend of decrease by extension of carbon-chain length, column densities of CH_{3}CCCCH and C_{6}H are on the trend. However, the column densities of linear-C_{6}H_{2}, and C_{7}H are as abundant as those of TMC-1 CP in spite of long carbon chain, i.e., they are not on the trend. The abundances of linear-C_{6}H_{2} and C_{7}H show that L1527 is rich for long carbon chains as well as TMC-1 CP.

The ultrasound-assisted oxidative scission of monoenic fatty acids by ruthenium tetroxide catalysis: influence of the mixture of solvents.

PubMed

Rup, Sandrine; Zimmermann, François; Meux, Eric; Schneider, Michel; Sindt, Michele; Oget, Nicolas

2009-02-01

Carboxylic acids and diacids were synthesized from monoenic fatty acids by using RuO4 catalysis, under ultrasonic irradiation, in various mixtures of solvents. Ultrasound associated with Aliquat 336 have promoted in water, the quantitative oxidative cleavage of the CH=CH bond of oleic acid. A design of experiment (DOE) shows that the optimal mixture of solvents (H2O/MeCN, ratio 1/1, 2.2% RuCl3/4.1 eq. NaIO4) gives 81% azelaic acid and 97% pelargonic acid. With the binary heterogeneous mixture H2O/AcOEt, the oxidation of the oleic acid leads to a third product, the alpha-dione 9,10-dioxostearic acid.

Effects of Tetrafluoroborate and Bis(trifluoromethylsulfonyl)amide Anions on the Microscopic Structures of 1-Methyl-3-octylimidazolium-Based Ionic Liquids and Benzene Mixtures: A Multiple Approach by ATR-IR, NMR, and Femtosecond Raman-Induced Kerr Effect Spectroscopy.

PubMed

Shirota, Hideaki; Kakinuma, Shohei; Itoyama, Yu; Umecky, Tatsuya; Takamuku, Toshiyuki

2016-01-28

The microscopic aspects of the two series of mixtures of 1-methyl-3-octylimidazolium tetrafluoroborate ([MOIm][BF4])-benzene and 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)amide ([MOIm][NTf2])-benzene were investigated by several spectroscopic techniques such as attenuated total reflectance IR (ATR-IR), NMR, and fs-Raman-induced Kerr effect spectroscopy (fs-RIKES). All three different spectroscopic results indicate that the anions more strongly interact with the cations in the [MOIm][BF4]-benzene mixtures than in the [MOIm][NTf2]-benzene mixtures. This also explains the different miscibility features between the two mixture systems well. The xC6H6 dependences of the chemical shifts and the C-H out-of-plane bending mode of benzene are similar: the changes are large in the high benzene concentration (xC6H6 > ∼ 0.6) compared to the low benzene concentration. In contrast, the linear xC6H6 dependences of the first moments of the low-frequency spectra less than 200 cm(-1) were observed in both the [MOIm][BF4]-benzene and [MOIm][NTf2]-benzene systems. The difference in the xC6H6 dependent features between the chemical shifts and intramolecular vibrational mode and the intermolecular/interionic vibrational bands might come from the different probing space scales. The traces of the parallel aromatic ring structure and the T-shape structure were found in the ATR-IR and NMR experiments, but fs-RIKES did not observe a clear trace of the local structure. This might imply that the interactions between the imidazolium and benzene rings are not strong enough to librate the imidazolium and benzene rings together. The bulk properties, such as miscibility, density, viscosity, and surface tension, of the two ionic liquid-benzene mixture series were also compared to the microscopic aspects.

Radial Microchannel Reactor (RMR) used in Steam Reforming CH4

DTIC Science & Technology

2013-05-13

process on land and at sea will reduce CO2 emission and enable cost reductions in the generation of energy in many small market economies. Peter R...size of GTL process on land and at sea will reduce CO2 emission and enable cost reductions in the generation of energy in many small market ...distribution of a 3.3:1 steam-methane mixture at 750 °C and 11 bar is: H2 45.8%, H2O 36.99%, CO 6.365%, CO2 6.681% and CH4 4.14% Barring any coking , this

Conversion of Syngas-Derived C2+ Mixed Oxygenates to C3-C5 Olefins over ZnxZryOz Mixed Oxides Catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Colin D.; Lebarbier, Vanessa M.; Flake, Matthew D.

2016-04-01

In this study we report on a ZnxZryOz mixed oxide type catalyst capable of converting a syngas-derived C2+ mixed oxygenate feedstock to isobutene-rich olefins. Aqueous model feed comprising of ethanol, acetaldehyde, acetic acid, ethyl acetate, methanol, and propanol was used as representative liquid product derived from a Rh-based mixed oxygenate synthesis catalyst. Greater than 50% carbon yield to C3-C5 mixed olefins was demonstrated when operating at 400-450oC and 1 atm. In order to rationalize formation of the products observed feed components were individually evaluated. Major constituents of the feed mixture (ethanol, acetaldehyde, acetic acid, and ethyl acetate) were found tomore » produce isobutene-rich olefins. C-C coupling was also demonstrated for propanol feedstock - a minor constituent of the mixed oxygenate feed - producing branched C6 olefins, revealing scalability to alcohols higher than ethanol following an analogous reaction pathway. Using ethanol and propanol feed mixtures, cross-coupling reactions produced mixtures of C4, C5, and C6 branched olefins. The presence of H2 in the feed was found to facilitate hydrogenation of the ketone intermediates, thus producing straight chain olefins as byproducts. While activity loss from coking is observed complete catalyst regeneration is achieved by employing mild oxidation. For conversion of the mixed oxygenate feed a Zr/Zn ratio of 2.5 and a reaction temperature of 450oC provides the best balance of stability, activity, and selectivity. X-ray diffraction and scanning transmission electron microscopy analysis reveals the presence of primarily cubic phase ZrO2 and a minor amount of the monoclinic phase, with ZnO being highly dispersed in the lattice. The presence of ZnO appears to stabilize the cubic phase resulting in less monoclinic phase as the ZnO concentration increases. Infrared spectroscopy shows the mixed oxide acid sites are characterized as primarily Lewis type acidity. The direct relationship between isobutene production and the ratio of basic/acidic sites was demonstrated. An optimized balance of active sites for isobutene production from acetone was obtained with a basic/acidic site ratio of ~2. This technology for the conversion of aqueous mixtures of C2+ mixed oxygenates provides significant advantages over other presently studied catalysts in that its unique properties permit the utilization of a variety of feeds in a consistently selective manner.« less

Optimization of the electrochemical performance of a Ni/Ce0.9Gd0.1O2-δ-impregnated La0.57Sr0.15TiO3 anode in hydrogen

NASA Astrophysics Data System (ADS)

Xia, Tian; Brüll, Annelise; Grimaud, Alexis; Fourcade, Sébastien; Mauvy, Fabrice; Zhao, Hui; Grenier, Jean-Claude; Bassat, Jean-Marc

2014-09-01

A-site deficient perovskite La0.57Sr0.15TiO3 (LSTO) materials are synthesized by a modified polyacrylamide gel route. X-ray diffraction pattern of LSTO indicates an orthorhombic structure. The thermal expansion coefficient of LSTO is 10.0 × 10-6 K-1 at 600 °C in 5%H2/Ar. LSTO shows an electrical conductivity of 2 S cm-1 at 600 °C in 3%H2O/H2. A new composite material, containing the porous LSTO backbone impregnated with small amounts of Ce0.9Gd0.1O2-δ (CGO) (3.4-8.3 wt.%) and Ni/Cu (2.0-6.3 wt.%), is investigated as an alternative anode for solid oxide fuel cells (SOFCs). Because of the substantial electro-catalytic activity of the fine and well-dispersed Ni particles on the surface of the ceramic framework, the polarization resistance of 6.3%Ni-8.3%CGO-LSTO anode reaches 0.73 Ω cm2 at 800 °C in 3%H2O/H2. In order to further improve the anodic performance, corn starch and carbon black are used as pore-formers to optimize the microstructure of anodes.

Stoichiometry and possible mechanism of SiH/sub 4/-O/sub 2/ explosions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartman, J.R.; Famil-Ghiriha, J.; Ring, M.A.

1987-04-01

The products of silane-O/sub 2/ mixture explosions vary with mixture composition. For O/sub 2/-rich mixtures (>70% O/sub 2/), the products are H/sub 2/O and SiO/sub 2/. As the mixtures become richer in silane, H/sub 2/ replaces H/sub 2/O as a final product. For very SiH/sub 4/-rich mixtures (>70% SiH/sub 4/), the products are H/sub 2/, SiO/sub x/, and Si. The fact that silane is totally consumed in silane-rich mixtures (70-90% silane) demonstrates that solid particle formation (SiO/sub 2/, SiO, and Si) occurs very rapidly and that the accompanying heat release is essential to drive the reactions to completion. It ismore » also clear that the explosion of a silane-rich mixture is primarily a thermal explosion of silane. Effects due to problems associated with upper pressure limit measurements and mechanistic aspects of the SiH/sub 4/-O/sub 2/ explosion reaction are discussed.« less

The OH + HBr reaction revisited

NASA Technical Reports Server (NTRS)

Ravishankara, A. R.; Wine, P. H.; Wells, J. R.

1985-01-01

Variable-temperature measurements of the rate coefficient /k(1)/ for the reaction OH + HBr yield Br + H2O are presented. The measurements are verified by two techniques: one involved a 266-nm pulsed-laser photolysis of O3/H2O/HBr/He mixtures in conjunction with time-resolved resonance fluorescence detection of OH, the second comprised pulsed laser-induced fluorescence detection of OH following 248-nm pulsed-laser photolysis of H2O2/HBr/Ar mixtures. It is reported that k(1) = (11.9 + or -1.4 x 10 to the -12th (cu cm)/(molecule)(s) independent of temperature. The measurements are compared with other available results.

Sanitizing radish seeds by simultaneous treatments with gaseous chlorine dioxide, high relative humidity, and mild heat.

PubMed

Bang, Jihyun; Choi, Moonhak; Son, Hyeri; Beuchat, Larry R; Kim, Yoonsook; Kim, Hoikyung; Ryu, Jee-Hoon

2016-11-21

Sanitizing radish seeds intended for edible sprout production was achieved by applying simultaneous treatments with gaseous chlorine dioxide (ClO 2 ), high relative humidity (RH, 100%), and mild heat (55°C). Gaseous ClO 2 was produced from aqueous ClO 2 (0.66ml) by mixing sulfuric acid (5% w/v) with sodium chlorite (10 mg/mL) in a sealed container (1.8L). Greater amounts of gaseous ClO 2 were measured at 23% RH (144ppm after 6h) than at 100% RH (66ppm after 6h); however, the lethal activity of gaseous ClO 2 against naturally occurring mesophilic aerobic bacteria (MAB) on radish seeds was significantly enhanced at 100% RH. For example, when exposed to gaseous ClO 2 at 23% RH, the number of MAB on radish seeds decreased from 3.7logCFU/g to 2.6logCFU/g after 6h. However, when exposed to gaseous ClO 2 at 100% RH for 6h, the MAB population decreased to 0.7logCFU/g after 6h. Gaseous ClO 2 was produced in higher amounts at 55°C than at 25°C, but decreased more rapidly over time at 55°C than at 25°C. The lethal activity of gaseous ClO 2 against MAB on radish seeds was greater at 55°C than at 25°C. When radish seeds were treated with gaseous ClO 2 (peak concentration: 195ppm) at 100% RH and 55°C, MAB were reduced to populations below the detectable level (<-0.7logCFU/g) within 2h without decreasing the seed germination rate (97.7%). The lethality of combined treatments against artificially inoculated Escherichia coli O157:H7 was also evaluated. When exposed to gaseous ClO 2 at 100% RH and 55°C for 6h, the initial number of E. coli O157:H7 (3.5logCFU/g) on radish seeds decreased to below the detection limit (0.7logCFU/g) by direct plating but it was not eliminated from seeds. The germination rate of radish seeds was not significantly (P>0.05) decreased after treatment for 6h. The information reported here will be useful when developing decontamination strategies for producing microbiologically safe radish seed sprouts. Copyright © 2016. Published by Elsevier B.V.

Molecular and polymeric uranyl and thorium hybrid materials featuring methyl substituted pyrazole dicarboxylates and heterocyclic 1,3-diketones

NASA Astrophysics Data System (ADS)

Carter, Korey P.; Kerr, Andrew T.; Taydakov, Ilya V.; Cahill, Christopher L.

2018-02-01

A series of seven novel f-element bearing hybrid materials have been prepared from either methyl substituted 3,4 and 4,5-pyrazoledicarboxylic acids, or heterocyclic 1,3- diketonate ligands using hydrothermal conditions. Compounds 1, [UO2(C6H4N2O4)2(H2O)], and 3, [Th(C6H4N2O4)4(H2O)5]·H2O feature 1-Methyl-1H-pyrazole-3,4-dicarboxylate ligands (SVI-COOH 3,4), whereas 2, [UO2(C6H4N2O4)2(H2O)], and 4, [Th(C6H5N2O4)(OH)(H2O)6]2·2(C6H5N2O4)·3H2O feature 1-Methyl-1H-pyrazole-4,5-dicarboxylate moieties (SVI-COOH 4,5). Compounds 5, [UO2(C13H15N4O2)2(H2O)]·2H2O and 6, [UO2(C11H11N4O2)2(H2O)]·4.5H2O feature 1,3-bis(4-N1-methyl-pyrazolyl)propane-1,3-dione and 1,3-bis(4-N1,3-dimethyl-pyrazolyl)propane-1,3-dione respectively, whereas the heterometallic 7, [UO2(C11H11N4O2)2(CuCl2)(H2O)]·2H2O is formed by using 6 as a metalloligand starting material. Single crystal X-ray diffraction indicates that all coordination to either [UO2]2+ or Th(IV) metal centers is through O-donation as anticipated. Room temperature, solid-state luminescence studies indicate characteristic uranyl emissive behavior for 1 and 2, whereas those for 5 and 6 are weak and poorly resolved.

The Unexpectedly Bright Comet C-2012 F6 (Lemmon) Unveiled at Near-Infrared Wavelengths

NASA Technical Reports Server (NTRS)

Paganini, Lucas; Disanti, Michael A.; Mumma, Michael J.; Villanueva, Geronimo L.; Bonev, Boncho P.; Keane, Jacqueline V.; Gibb, Erika L.; Boehnhardt, Hermann; Meech, Karen J.

2013-01-01

We acquired near-infrared spectra of the Oort cloud comet C/2012 F6 (Lemmon) at three different heliocentric distances (R h) during the comet's 2013 perihelion passage, providing a comprehensive measure of the outgassing behavior of parent volatiles and cosmogonic indicators. Our observations were performed pre-perihelion at R h = 1.2 AU with CRIRES (on 2013 February 2 and 4), and post-perihelion at R h = 0.75 AU with CSHELL (on March 31 and April 1) and R h = 1.74 AU with NIRSPEC (on June 20). We detected 10 volatile species (H2O, OH* prompt emission, C2H6, CH3OH, H2CO, HCN, CO, CH4, NH3, and NH2), and obtained upper limits for two others (C2H2 and HDO). One-dimensional spatial profiles displayed different distributions for some volatiles, confirming either the existence of polar and apolar ices, or of chemically distinct active vents in the nucleus. The ortho-para ratio for water was 3.31 +/- 0.33 (weighted mean of CRIRES and NIRSPEC results), implying a spin temperature >37 K at the 95% confidence limit. Our (3s) upper limit for HDO corresponds to D/H < 2.45 × 10-3 (i.e., <16 Vienna Standard Mean Ocean Water, VSMOW). At R h = 1.2 AU (CRIRES), the production rate for water was Q(H2O) = 1.9 +/- 0.1 × 1029 s-1 and its rotational temperature was T rot 69 K. At R h = 0.75 AU (CSHELL), we measured Q(H2O) = 4.6 +/- 0.6 × 1029 s-1 and T rot = 80 K on March 31, and 6.6 +/- 0.9 × 1029 s-1 and T rot = 100 K on April 1. At R h = 1.74 AU (NIRSPEC), we obtained Q(H2O) = 1.1 +/- 0.1 × 1029 s-1 and T rot 50 K. The measured volatile abundance ratios classify comet C/2012 F6 as rather depleted in C2H6 and CH3OH, while HCN, CH4, and CO displayed abundances close to their median values found among comets. H2CO was the only volatile showing a relative enhancement. The relative paucity of C2H6 and CH3OH (with respect to H2O) suggests formation within warm regions of the nebula. However, the normal abundance of HCN and hypervolatiles CH4 and CO, and the enhancement of H2CO, may indicate a possible heterogeneous nucleus of comet C/2012 F6 (Lemmon), possibly as a result of radial mixing within the protoplanetary disk

Effects of sol-gel synthesis on 5Fe-15Mn-40Zn-40Ti-O mixed oxide structure and its H2S removal efficiency from industrial gas streams.

PubMed

Polychronopoulou, Kyriaki; Efstathiou, Angelos M

2009-06-15

A novel Fe-Mn-Zn-Ti-O mixed metal oxide has been developed for efficient low-temperature (25-50 degrees C) removal of H2S from a gas mixture containing 600 ppm H2S, 25 vol% H2, 7.5 vol % CO2, and 1-3 vol% H2O that simulates typical conditions experienced at the outlet of a bioreactor loaded with sulfate metal reducing bacteria (SMRB) that converts toxic Cr6+ and As5+ present in ground and surface waters and soils into nontoxic elements. During the latter conversion H2S gas is produced and has to be treated. In the present work it is demonstrated for the first time that by using the sol-gel synthesis route at given experimental conditions (e.g., metal precursor salts, solvent system, and solution pH), optimum structural properties for the Fe-Mn-Zn-Ti-O solid can be obtained for maximization of H2S uptake. In particular, at 25 degrees C an H2S uptake (0.085 g H2S/g solid) larger by at least a factor of 3 compared to a commercial Ni-based H2S absorbent material was obtained.

Influence of the Organic Species and Oxoanion in the Synthesis of two Uranyl Sulfate Hydrates, (H 3 O) 2 [(UO 2 ) 2 (SO 4 ) 3 ­(H 2 O)]·7H 2 O and (H 3 O) 2 [(UO 2 ) 2 (SO 4 ) 3 (H 2 O)]·4H 2 O, and a Uranyl Selenate-Selenite [C 5 H 6 N][(UO 2 )(SeO 4 )(HSeO 3 )

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jouffret, Laurent J.; Wylie, Ernest M.; Burns, Peter C.

2012-08-08

Two uranyl sulfate hydrates, (H3O)2[(UO2)2(SO4)3(H2O)]·7H2O (NDUS) and (H3O)2[(UO2)2(SO4)3(H2O)]·4H2O (NDUS1), and one uranyl selenate-selenite [C5H6N][(UO2)(SeO4)(HSeO3)] (NDUSe), were obtained and their crystal structures solved. NDUS and NDUSe result from reactions in highly acidic media in the presence of L-cystine at 373 K. NDUS crystallized in a closed vial at 278 K after 5 days and NDUSe in an open beaker at 278 K after 2 weeks. NDUS1 was synthesized from aqueous solution at room temperature over the course of a month. NDUS, NDUS1, and NDUSe crystallize in the monoclinic space group P21/n, a = 15.0249(4) Å,b = 9.9320(2) Å, c = 15.6518(4)more » Å, β = 112.778(1)°, V = 2153.52(9) Å3,Z = 4, the tetragonal space group P43212, a = 10.6111(2) Å,c = 31.644(1) Å, V = 3563.0(2) Å3, Z = 8, and in the monoclinic space group P21/n, a = 8.993(3) Å, b = 13.399(5) Å, c = 10.640(4) Å,β = 108.230(4)°, V = 1217.7(8) Å3, Z = 4, respectively.The structural units of NDUS and NDUS1 are two-dimensional uranyl sulfate sheets with a U/S ratio of 2/3. The structural unit of NDUSe is a two-dimensional uranyl selenate-selenite sheets with a U/Se ratio of 1/2. In-situ reaction of the L-cystine ligands gives two distinct products for the different acids used here. Where sulfuric acid is used, only H3O+ cations are located in the interlayer space, where they balance the charge of the sheets, whereas where selenic acid is used, interlayer C5H6N+ cations result from the cyclization of the carboxyl groups of L-cystine, balancing the charge of the sheets.« less

The relationship between reorientational molecular motions and phase transitions in [Mg(H{sub 2}O){sub 6}](BF{sub 4}){sub 2}, studied with the use of {sup 1}H and {sup 19}F NMR and FT-MIR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mikuli, Edward, E-mail: mikuli@chemia.uj.edu.pl; Hetmańczyk, Joanna; Grad, Bartłomiej

2015-02-14

A {sup 1}H and {sup 19}F nuclear magnetic resonance study of [Mg(H{sub 2}O){sub 6}](BF{sub 4}){sub 2} has confirmed the existence of two phase transitions at T{sub c1} ≈ 257 K and T{sub c2} ≈ 142 K, detected earlier by the DSC method. These transitions were reflected by changes in the temperature dependences of both proton and fluorine of second moments M{sub 2}{sup H} and M{sub 2}{sup F} and of spin-lattice relaxation times T{sub 1}{sup H} and T{sub 1}{sup F}. The study revealed anisotropic reorientations of whole [Mg(H{sub 2}O){sub 6}]{sup 2+} cations, reorientations by 180° jumps of H{sub 2}O ligands, andmore » aniso- and isotropic reorientations of BF{sub 4}{sup −} anions. The activation parameters for these motions were obtained. It was found that the phase transition at T{sub c1} is associated with the reorientation of the cation as a whole unit around the C{sub 3} axis and that at T{sub c2} with isotropic reorientation of the BF{sub 4}{sup −} anions. The temperature dependence of the full width at half maximum value of the infrared band of ρ{sub t}(H{sub 2}O) mode (at ∼596 cm{sup −1}) indicated that in phases I and II, all H{sub 2}O ligands in [Mg(H{sub 2}O){sub 6}]{sup 2+} perform fast reorientational motions (180° jumps) with a mean value of activation energy equal to ca 10 kJ mole{sup −1}, what is fully consistent with NMR results. The phase transition at T{sub c1} is associated with a sudden change of speed of fast (τ{sub R} ≈ 10{sup −12} s) reorientational motions of H{sub 2}O ligands. Below T{sub c2} (in phase III), the reorientations of certain part of the H{sub 2}O ligands significantly slow down, while others continue their fast reorientation with an activation energy of ca 2 kJ mole{sup −1}. This fast reorientation cannot be evidenced in NMR relaxation experiments. Splitting of certain IR bands connected with H{sub 2}O ligands at the observed phase transitions suggests a reduction of the symmetry of the octahedral [Mg(H{sub 2}O){sub 6}]{sup 2+} complex cation.« less

Equatorially connected diruthenium(II,III) units toward paramagnetic supramolecular structures with singular magnetic properties.

PubMed

Barral, M Carmen; Gallo, Teresa; Herrero, Santiago; Jiménez-Aparicio, Reyes; Torres, M Rosario; Urbanos, Francisco A

2006-05-01

The reaction of Ru2Cl(O2CMe)(DPhF)3 (DPhF = N,N'-diphenylformamidinate) with mono- and polycarboxylic acids gives a clean substitution of the acetate ligand, leading to the formation of complexes Ru2Cl(O2CC6H5)(DPhF)3 (1), Ru2Cl(O2CC6H4-p-CN)(DPhF)3 (2), [Ru2Cl(DPhF)3(H2O)]2(O2C)2 (3), [Ru2Cl(DPhF)3]2[C6H4-p-(CO2)2] (4), and [Ru2Cl(DPhF)3]3[C6H3-1,3,5-(CO2)3] (5). The preparation of [Ru2(NCS)(DPhF)3]3[C6H3-1,3,5-(CO2)3] (6) and {[Ru2(DPhF)3(H2O)]3[C6H3-1,3,5-(CO2)3]}(SO3CF3)3 (7) from 5 is also described. All complexes are characterized by elemental analysis, IR and electronic spectroscopy, mass spectrometry, cyclic voltammetry, and variable-temperature magnetic measurements. The crystal structure determinations of complexes 2.0.5THF and 3.THF.4H2O (THF = tetrahydrofuran) are reported. The reactions carried out demonstrate the high chemical stability of the fragment [Ru2(DPhF)3]2+, which is preserved in all tested experimental conditions. The stability of this fragment is also corroborated by the mass spectra. Electrochemical measurements reveal in all complexes one redox process due to the equilibrium Ru2(5+) <--> Ru2(6+). In the polynuclear complex 7, some additional oxidation processes are also observed that have been ascribed to the presence of two types of dimetallic units rather than two consecutive reversible oxidations. The magnetic behavior toward temperature for complexes 1-7 from 300 to 2 K is analyzed. Complexes 1-7 show low values of antiferromagnetic coupling in accordance with the molecular nature in 1 and 2 and the absence of important antiferromagnetic interaction through the carboxylate bridging ligands in 3-7, respectively. In addition, the magnetic properties of complex 7 do not correspond to any magnetic behavior described for diruthenium(II,III) complexes. The experimental data of compound 7 are simulated considering a physical mixture of S = 1/2 and 3/2 spin states. This magnetic study demonstrates the high sensitivity of the electronic configuration of the unit [Ru2(DPhF)3]2+ to small changes in the nature of the axial ligands. Finally, the energy gap between the pi and delta orbitals in these types of compounds allows the tentative assignment of the transition pi --> delta.

Structure and thermodynamic stability of UTa 3 O 10 , a U( v )-bearing compound

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, Xiaofeng; Lipp, Christian; Tiferet, Eitan

Heating a mixture of uranyl(VI) nitrate and tantalum(V) oxide in the molar ratio of 2 : 3 to 1400 °C resulted in the formation of a new compound, UTa 3O 10. The honey colored to yellow brown crystals of UTa 3O 10 crystallize in an orthorhombic structure with the space group Fddd (no. 70), lattice parameters a = 7.3947(1), b = 12.7599(2), c = 15.8156(2) Å, and Z = 8. Vertex sharing [TaO 6] 7- octahedra of two crystallographically distinct Ta cations form a three dimensional tantalate framework. Within this framework, six membered rings of [TaO 6] 7- octahedra aremore » formed within the (001) plane. The center of these rings is occupied by the uranyl cations [UO 2] +, with an oxidation state of +5 for uranium. The pentavalence of U and Ta was confirmed by X-ray photoelectron spectroscopy and X-ray adsorption spectroscopy. The enthalpy of formation of UTa 3O 10 from Ta 2O 5, β-U 3O 7, and U 3O 8 has been determined to be 13.1 ± 18.1 kJ mol -1 using high temperature oxide melt solution calorimetry with sodium molybdate as the solvent at 700 °C. The close to zero enthalpy of formation of UTa 3O 10 can be explained by closely balanced structural stabilizing and destabilizing factors, which may also apply to other UM 3O 10 compounds.« less

A moderate distortion of the `picket-fence' porphyrin (cryptand-222)potassium chlorido[meso-α,α,α,α-tetrakis(o-pivalamidophenyl)porphyrinato]ferrate(II) n-hexane monosolvate.

PubMed

Yu, Qiang; Liu, Diansheng; Li, Xiangjun; Li, Jianfeng

2015-10-01

As representative porphyrin model compounds, the structures of `picket-fence' porphyrins have been studied intensively. The title solvated complex salt {systematic name: (4,7,13,16,21,24-hexaoxa-1,10-diazabicyclo[8.8.8]hexacosane)potassium(I) [5,10,15,20-tetrakis(2-tert-butanamidophenyl)porphyrinato]iron(II) n-hexane monosolvate}, [K(C18H36N2O6)][Fe(C64H64N8O4)Cl]·C6H14 or [K(222)][Fe(TpivPP)Cl]·C6H14 [222 is cryptand-222 or 4,7,13,16,21,24-hexaoxa-1,10-diazabicyclo[8.8.8]hexacosane, and TpivPP is meso-α,α,α,α-tetrakis(o-pivalamidophenyl)porphyrinate(2-)], [K(222)][Fe(TpivPP)Cl]·C6H14, is a five-coordinate high-spin iron(II) picket-fence porphyrin complex. It crystallizes with a potassium cation chelated inside a cryptand-222 molecule; the average K-O and K-N distances are 2.81 (2) and 3.05 (2) Å, respectively. One of the protecting tert-butyl pickets is disordered. The porphyrin plane presents a moderately ruffled distortion, as suggested by the atomic displacements. The axial chloride ligand is located inside the molecular cavity on the hindered porphyrin side and the Fe-Cl bond is tilted slightly off the normal to the porphyrin plane by 4.1°. The out-of-plane displacement of the metal centre relative to the 24-atom mean plane (Δ24) is 0.62 Å, indicating a noticeable doming of the porphyrin core.

On chemical inhibition of shock wave ignition of hydrogen-oxygen mixtures

NASA Astrophysics Data System (ADS)

Drakon, A. V.; Eremin, A. V.; Mikheyeva, E. Yu

2018-01-01

In this work an influence of the wide range of various inhibitors, namely CCl4, CF3H, C2F4Br2, (CH3O)3P, CF3I and C3F7I on shock-induced ignition of hydrogen was experimentally investigated. Observed temperature dependencies of induction times indicates that CF3H and (CH3O)3P do not show noticeable inhibiting activity at given conditions, while the effectiveness of halogen-containing specie dramatically increases in a row Cl → Br → I. It is shown that the most effective inhibitors of ignition of hydrogen-oxygen mixtures are iodinated hydrocarbons CF3I and C3F7I.

Layered zinc hydroxide monolayers by hydrolysis of organozincs† †Electronic supplementary information (ESI) available: LZH-OAc and LZH-OHex characterisation data (powder XRD, IR, SEM, TGA, DTA), bulk LZH-Ole solid-state SAXS data, exfoliated LZH-Ole TEM data, AFM data with histogram and line profiles of samples (N ∼ 100) taken from image, UV-vis spectra of ZnO@Ole and ZnO thin films, 1H NMR of LZH-Ole, ZnO@Ole and pre-hydrolysis mixture of synthesis of LZH-Ole, photographs of thin films of LZH-Ole and ZnO on glass substrate, method used for determining the content of ZnO nanoparticles in synthesis mixture, calculation of yields of LZHs based on Zn. See DOI: 10.1039/c7sc04256f

PubMed Central

Leung, Alice H. M.; Pike, Sebastian D.; Clancy, Adam J.; Yau, Hin Chun; Lee, Won Jun; Orchard, Katherine L.

2018-01-01

2D inorganic materials and their exfoliated counterparts are both of fundamental interest and relevant for applications including catalysis, electronics and sensing. Here, a new bottom-up synthesis route is used to prepare functionalised nanoplatelets, in apolar organic solvents, via the hydrolysis of organometallic reagents; the products can be prepared in high yield, at room temperature. In particular, a series of layered zinc hydroxides, coordinated by aliphatic carboxylate ligands, were produced by the hydrolysis of diethyl zinc and zinc carboxylate mixtures, optimally at a molar ratio of [COOR]/[Zn] = 0.6. Layered zinc hydroxides coordinated by oleate ligands form high concentration solutions of isolated monolayers (3 nm thick x ∼ 26 nm) in apolar organic solvents (up to 23 mg mL–1 in toluene), as confirmed by both atomic force and transmission electron microscopies of deposited species. The high solubility of the product allows the synthetic pathway to be monitored directly in situ through 1H NMR spectroscopy. The high solubility also provides a route to solution deposition of active functional materials, as illustrated by the formation of nanoporous films of optically transparent porous zinc oxide (1 μm thickness) after annealing at 500 °C. This new organometallic route to 2D materials obviates common complications of top-down exfoliation syntheses, including sonochemical-degradation and low yields of aggregated polydispersed layers, and may potentially be extended to a wide range of systems. PMID:29719687

Benzene and toluene influence with or without nitrogen dioxide on inorganic pigments of works of art—Part II

NASA Astrophysics Data System (ADS)

Agelakopoulou, T.; Bassiotis, I.; Metaxa, E.; Roubani-Kalantzopoulou, F.

Air pollution has a great impact on the social and economic aspects all over the world. In order to account the human interaction with the atmospheric environment, a suitable scientific basis is needed. That is why six physicochemical quantities have been determined in a previous work for each one heterogeneous system between organic volatile pollutants and oxide-pigments of works of art. This investigation is extended in order to determine experimentally five new ones. Thus, a more precise contribution to the elucidation of the mechanism of the deterioration of various works of art in museums is achieved. These physicochemical quantities are: (1) local adsorption energies, (2) local monolayer capacities, (3) local adsorption isotherms, (4) density probability function, and (5) pollutant concentration on the oxide-pigment at equilibrium. All these adsorption parameters mentioned above have been calculated as a function of experimental time for the systems: C 6H 6/TiO 2, C 6H 6/NO 2/TiO 2, C 6H 6/Cr 2O 3, C 6H 6/NO 2/Cr 2O 3, C 6H 5CH 3/TiO 2, C 6H 5CH 3/NO 2/TiO 2, C 6H 5CH 3/Cr 2O 3, C 6H 5CH 3/NO 2/Cr 2O 3, C 6H 6/PbO, C 6H 6/NO 2/PbO, C 6H 5CH 3/PbO, and C 6H 5CH 3/NO 2/PbO for the first time. Thus, in this work we shall stress the recent new aspect of Reversed Flow-(Inverse) Gas Chromatography (RF-GC or RF-IGC), i.e. the time-resolved chromatography related to the evaluation of some important adsorption parameters. Gas Chromatography is a promising meeting place of surface science and atmospheric chemistry.

Detection of interstellar ethylene oxide (c-C2H4O).

PubMed

Dickens, J E; Irvine, W M; Ohishi, M; Ikeda, M; Ishikawa, S; Nummelin, A; Hjalmarson, A

1997-11-10

We report the identification of 10 transitions that support the detection of the small cyclic molecule ethylene oxide (c-C2H4O) in Sgr B2N. Although one of these transitions is severely blended, so that an accurate intensity and line width could not be determined, and two other lines are only marginally detected, we have done Gaussian fits to the remaining seven lines and have performed a rotation diagram analysis. Our results indicate a rotation temperature T(rot) = 18 K and a molecular column density N(c-C2H4O) = 3.3 x 10(14) cm-2, corresponding to a fractional abundance relative to molecular hydrogen of order 6 x 10(-11). This is a factor of more than 200 higher than the abundance for this molecule suggested by the "new standard" chemistry model of Lee, Bettens, & Herbst. This result suggests that grain chemistry might play an effective role in the production of c-C2H4O. No transitions of this molecule were detected in either Sgr B2M or Sgr B2NW.

Synthesis and physico-chemical studies on neodymium(III) and samarium(III) complexes with tetraaza macrocyclic ligands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goel, S.; Pandey, U.K.; Pandey, O.P.

1988-05-01

Reactions of neodymium trichloride and samarium trichloride with 6,7,13,14-R/sub 4/ - 3,10-X/sub 2/-(14)-5,7,12,14-tetraene-1,5,8,12-N/sub 4/-(2,4,9,11-N/sub 4/) (R = CH/sub 3/, X = 0 (L/sub 1//sup (1)/); R = C/sub 6/H/sub 5/, X = O (L/sub 1//sup (2)/); R = CH/sub 3/, X = S(L/sub 2//sup (1)/)) and R = C/sub 6/H/sub 5/, X = S(/sub 2//sup (2)/)) have been studied in ethanol and complexes of the type (M(L/sub 1//sup (1)/ or L/sub 1//sup (2)/))Cl/sub 3/ and (M(L/sub 2//sup (1)/ or L/sub 2//sup (2)/)(H/sub 2/O)/sub 2/)Cl/sub 3/ (M = Nd(III) and Sm(III)) have been isolated. In addition, macrocyclic complexes of Nd(III) andmore » Sm(III) with another series of tetraaza ligands, viz, 5,6,11,12-R/sub 4/-3,8-X/sub 2/-(12)-4,6,10,12-tetraene-1,4,7,10-N/sub 4/-(2,9-N/sub 2/) (R = CH/sub 3/, X = O (L/sub 3//sup (1)/); R = C/sub 6/H/sub 5/, X = O(L/sub 3//sup (2)/); R = CH/sub 3/, X = S(L/sub 4//sup (1)/); R = C/sub 6/H/sub 5/, X = S(L/sub 4//sup (2)/)), formulated as (M(L/sub 3//sup (1)/, L/sub 3//sup (2)/, L/sub 4//sup (1)/ or L/sub 4//sup (2)/)(H/sub 2/O)/sub 2/)Cl/sub 3/ (M = Nd(III) and Sm(III)) have been prepared by template condensation of Nd(III) and Sm(III) complexes of diacetylbis(semicarbazonethiosemicarbazone) or benzilibis(semicarbazonethiosemicarbazone) with diacetyl or benzil. The complexes have been identified by elemental analysis, electrical conductance, spectral and thermal measurements.« less

Stereoselective synthesis of novel thioglycosyl heterocycles

NASA Astrophysics Data System (ADS)

El Ashry, El Sayed H.; Awad, Laila F.; Al Moaty, Mohamed N. Abd; Ghabbour, Hazem A.; Barakat, Assem

2018-01-01

In this work, the synthesis of novel 1,2,4-triazole thioglycoside heterocycles 4, 5, and 8 were achieved by the reaction of 1,2,3,4,6-penta-O-acetyl-β-D-glucopyranose (2) and galactopyranose (3) with 4-((4-arylidene)amino)-5-methyl-1,2,4-triazole-3-thiol derivatives 1 and 6 in the presence of boron trifluoride etherate (BF3·Et2O) as a promoter under nitrogen in CH2Cl2. Exclusive β-stereoselectivity of the formed glycosidic bond was confirmed by X-ray analysis of 4 as well as its spectral data. Different stereoselectivities were observed when the acceptor 9, having an ortho phenolic OH group, was coupled with the donors 2 or 3, under the same reaction conditions. Similarly, treatment of a mixture of 1-O-acetyl-2,3,5-tri-O-benzoyl-β-D-ribofuranose (16) and the thiol acceptors 1 and 15 afforded the β-thioribofuranosides 17 and 18, respectively. The β-stereoselectivity of the reaction was confirmed by 1H, 13C, 1Hsbnd 1H 2D, and 1Hsbnd 13C 2D NMR spectral analysis.

Investigation of the Electrical Characteristics of Al/p-Si/Al Schottky Diode

NASA Astrophysics Data System (ADS)

Şenarslan, Elvan; Güzeldir, Betül; Sağlam, Mustafa

2016-04-01

In this study, p-type Si semiconductor wafer with (100) orientation, 400 μm thickness and 1-10 Ω cm resistivity was used. The Si wafer before making contacts were chemically cleaned with the Si cleaning procedure which for remove organic contaminations were ultrasonically cleaned at acetone and methanol for 10 min respectively and then rinsed in deionized water of 18 MΩ and dried with high purity N2. Then respectively RCA1(i.e., boiling in NH3+H2O2+6H2O for 10 min at 60°C ), RCA2 (i.e., boiling in HCl+H2O2+6H2O for 10 min at 60°C ) cleaning procedures were applied and rinsed in deionized water followed by drying with a stream of N2. After the cleaning process, the wafer is immediately inserted in to the coating unit. Ohmic contact was made by evaporating of Al on the non-polished side of the p-Si wafer pieces under ~ 4,2 10-6 Torr pressure. After process evaporation, p-Si with omic contac thermally annealed 580°C for 3 min in a quartz tube furnace in N2. Then, the rectifier contact is made by evaporation Al metal diameter of about 1.0 mm on the polished surface of p-Si in turbo molecular pump at about ~ 1 10-6 Torr. Consequently, Al/p-Si/Al Schottky diode was obtained. The I-V measurements of this diode performed by the use of a KEITLEY 487 Picoammeter/Voltage Source and the C-V measurements were performed with HP 4192A (50-13 MHz) LF Impedance Analyzer at room temperature and in dark.

Influence of Alumina Binder Content on Catalytic Performance of Ni/HZSM-5 for Hydrodeoxygenation of Cyclohexanone

PubMed Central

Kong, Xiangjin; Liu, Junhai

2014-01-01

The influence of the amount of alumina binders on the catalytic performance of Ni/HZSM-5 for hydrodeoxygenation of cyclohexanone was investigated in a fixed-bed reactor. N2 sorption, X-ray diffraction, H2-chemisorption and temperature-programmed desorption of ammonia were used to characterize the catalysts. It can be observed that the Ni/HZSM-5 catalyst bound with 30 wt.% alumina binder exhibited the best catalytic performance. The high catalytic performance may be due to relatively good Ni metal dispersion, moderate mesoporosity, and proper acidity of the catalyst. PMID:25009974

Influence of alumina binder content on catalytic performance of Ni/HZSM-5 for hydrodeoxygenation of cyclohexanone.

PubMed

Kong, Xiangjin; Liu, Junhai

2014-01-01

The influence of the amount of alumina binders on the catalytic performance of Ni/HZSM-5 for hydrodeoxygenation of cyclohexanone was investigated in a fixed-bed reactor. N2 sorption, X-ray diffraction, H2-chemisorption and temperature-programmed desorption of ammonia were used to characterize the catalysts. It can be observed that the Ni/HZSM-5 catalyst bound with 30 wt.% alumina binder exhibited the best catalytic performance. The high catalytic performance may be due to relatively good Ni metal dispersion, moderate mesoporosity, and proper acidity of the catalyst.

Synthesis and structure of heptaaqua(nitrilotris(methylenephosphonato))(dibarium)sodium monohydrate [Na(H{sub 2}O){sub 3}(μ{sup 6}-NH(CH{sub 2}PO{sub 3}){sub 3})(μ-H{sub 2}O){sub 3}Ba{sub 2}(H{sub 2}O)] · H{sub 2}O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Somov, N. V., E-mail: somov@phys.unn.ru; Chausov, F. F., E-mail: xps@ftiudm.ru; Zakirova, R. M., E-mail: ftt@udsu.ru

Crystals of the monohydrate form of heptaaqua(nitrilotris(methylenephosphonato))(dibarium) sodium [Na(H{sub 2}O{sub )3}(µ{sup 6}-NH(CH{sub 2}PO{sub 3}){sub 3})(µ-H{sub 2}O){sub 3}Ba{sub 2}(H{sub 2}O)] · H{sub 2}O are obtained; space group P2{sub 1}/c, Z = 4; a = 13.9117(10) Å, b = 11.54030(10) Å, and c = 24.1784(17) Å, ß = 148.785(18)°. The Na atom is coordinated octahedrally by one oxygen atom of a phosphonate group and five water molecules, including two bridging molecules. Ba atoms occupy two inequivalent crystallographic positions with coordination number eight and nine. The coordination spheres of both Ba atoms include two water molecules. Each ligand is bound to one Namore » atom and five Ba atoms forming three Ba–O–P–O and five Ba–O–P–C–N–C–P–O chelate cycles. In addition to the coordination bonds, molecules, including the solvate water molecule, are involved in hydrogen bonds in the crystal packing.« less

Impact of certain plants and synthetic molluscicides on some fresh water snails and fish.

PubMed

Mosta-Fa, B B; el-Deeb, Fatma A; Ismail, Nahid M; el-Said, K M

2005-12-01

The LC50 (78, 85 ppm) and LC90 (88, 135 ppm) of Anagalis arvensis and Calendula micrantha respectively against Biomphalaria alexandrina were higher than those of the non-target snails, Physa acuta, Planorbis planorbis, Helisoma duryi and Melanoides tuberculata. In contrast, the LC50 of Niclosamide (0.11 ppm) and Copper sulphate (CuSO4) (0.42 ppm) against B. alexandrina were lower than those of the non-target snails. The mortalities percentage among non-target snails ranged between 0.0 & 20% when sublethal concentrations of CuSO4 against B. alexandrina mixed with those of C. micrantha and between 0.0 & 40% when mixed with A. arvensis. Mortalities ranged between 0.0 & 50% when Niclosamide was mixed with each of A. arvensis and C. micrantha. A. arvensis induced 100% mortality on Oreochromis niloticus after 48 hrs exposure and after 24 hrs for Gambusia affinis. C. micrantha was non-toxic to the fish. The survival rate of O. niloticus and G. affinis after 48 hrs exposure to 0.11 ppm of Niclosamide were 83.3% & 100% respectively. These rates were 91.7% & 93.3% respectively when each of the two fish species was exposed to 0.42 ppm of CuSO4. Mixture of sub-lethal concentrations of A. arvensis against B. alexandrina and those of Niclosamide or CuSO4 at ratios 10:40 & 25:25 induced 66.6% mortalities on O. niloticus and 83.3% at 40:10. These mixtures caused 100% mortalities on G. affinis at all ratios. A. arvensis CuSO4 mixtures at 10:40 induced 83.3% & 40% mortalities on O. niloticus and G. affinis respectively and 100% mortalities on both fish species at ratios 25:25 & 40:10. A mixture of sub-lethal concentrations of C. micrantha against B. alexandrina and of Niclosamide or CuSO4 caused mortalities of O. niloticus between 0.0 & 33.3% and between 5% & 35% of G. affinis. The residue of Cu in O. niloticus were 4.69, 19.06 & 25.37 mg/1kgm fish after 24, 48 & 72 hrs exposure to LC0 of CuSO4 against B. alexandrina respectively.

The Relationship of the Silicon Surface Roughness and Gate Oxide Integrity in NH4OH/H2O2 Mixtures

NASA Astrophysics Data System (ADS)

Meuris, M.; Verhaverbeke, S.; Mertens, P. W.; Heyns, M. M.; Hellemans, L.; Bruynseraede, Y.; Philipossian, A.

1992-11-01

In this study some recent findings on the cleaning action of the NH4OH/H2O2 (SC1) step in a pre-gate oxidation cleaning (RCA cleaning) are given. An important parameter in this mixture is the NH4OH/H2O2 ratio. The Fe contamination on the silicon surface after this cleaning step is found to increase upon decreasing the NH4OH/H2O2 ratio. This can be attributed to the incorporation of Fe in the chemical oxide, grown by the hydrogen peroxide. The particle removal efficiency of the cleaning step is found to decrease upon decreasing the NH4OH/H2O2 ratio. On the other hand, using a lower NH4OH concentration results in a less severe silicon surface roughening. It is demonstrated in this study that the NH4OH/H2O2 ratio during the SC1 step of the cleaning is the determining parameter for the breakdown properties of a gate oxide. A (0.25/1/5) NH4OH/H2O2/H2O mixture at 75°C in our experimental conditions is suggested to be the best compromise between particle removal and surface roughness during the SC1 step.

pH-specific synthesis and spectroscopic, structural, and magnetic studies of a chromium(III)-citrate species. Aqueous solution speciation of the binary chromium(III)-citrate system.

PubMed

Gabriel, C; Raptopoulou, C P; Terzis, A; Tangoulis, V; Mateescu, C; Salifoglou, A

2007-04-16

In an attempt to understand the aqueous interactions of Cr(III) with the low-molecular-mass physiological ligand citric acid, the pH-specific synthesis in the binary Cr(III)-citrate system was explored, leading to the complex (NH4)4[Cr(C6H4O7)(C6H5O7)].3H2O (1). 1 crystallizes in the monoclinic space group I2/a, with a = 19.260(10) A, b = 10.006(6) A, c = 23.400(10) A, beta = 100.73(2) degrees , V = 4431(4) A3, and Z = 8. 1 was characterized by elemental analysis and spectroscopic, structural, thermal, and magnetic susceptibility studies. Detailed aqueous speciation studies in the Cr(III)-citrate system suggest the presence of a number of species, among which is the mononuclear [Cr(C6H4O7)(C6H5O7)]4- complex, optimally present around pH approximately 5.5. The structure of 1 reveals a mononuclear octahedral complex of Cr(III) with two citrate ligands bound to it. The two citrate ligands have different deprotonation states, thus signifying the importance of the mixed deprotonation state in the coordination sphere of the Cr(III) species in aqueous speciation. The latter reveals the distribution of numerous species, including 1, for which the collective structural, spectroscopic, and magnetic data point out its physicochemical profile in the solid state and in solution. The importance of the synthetic efforts linked to 1 and the potential ramifications of Cr(III) reactivity toward both low- and high-molecular-mass biotargets are discussed in light of (a) the quest for well-characterized soluble Cr(III) species that could be detected and identified in biologically relevant fluids, (b) ongoing efforts to delineate the aqueous speciation of the Cr(III)-citrate system and its link to biotoxic Cr(III) manifestations, and (c) the synthetic utility of convenient Cr(III) precursors in the synthesis of advanced materials.

Weakly-agglomerated nanocrystalline (ZrO 2) 0.9(Yb 2O 3) 0.1 powders hydrothermally synthesized at low temperature

NASA Astrophysics Data System (ADS)

Dell'Agli, Gianfranco; Mascolo, Giuseppe; Mascolo, Maria Cristina; Pagliuca, Concetta

2006-09-01

Nanocrystalline ytterbia (10 mol%)-doped cubic zirconia powders were synthesized by hydrothermal treatment of either an amorphous co-precipitate of hydrated ytterbia-zirconia or of zirconia xerogel in mixture with crystalline Yb 2O 3. The treatments were performed at 110 °C in the presence of diluted (0.2 M) or concentrated (2.0 M) solution of (K 2CO 3 + KOH) mineralizer and for different reaction times. The reaction times for the full crystallization of cubic-YbSZ-based products were determined for both the employed precursors and for each mineralizer solution. The various fully crystallized products were characterized in their degree of agglomeration and sintered at 1500 °C for 2 h. The best performance on sintering was achieved with the less agglomerated powder synthesized from the mechanical mixture and in the presence of the diluted solution of the mineralizer. The resulting density was the highest achieved with materials having the same composition.

Pharmacokinetics after intravenous, subcutaneous, and oral administration of enrofloxacin to alpacas.

PubMed

Gandolf, A Rae; Papich, Mark G; Bringardner, Amy B; Atkinson, Mark W

2005-05-01

To determine plasma concentrations of enrofloxacin and the active metabolite ciprofloxacin after p.o, s.c., and i.v. administration of enrofloxacin to alpacas. 6 adult female alpacas. A crossover design was used for administration of 3 single-dose treatments of enrofloxacin to alpacas, which was followed by an observational 14-day multiple-dose regimen. Single-dose treatments consisted of i.v. and s.c. administration of injectable enrofloxacin (5 mg/kg) and p.o administration of enrofloxacin tablets (10 mg/kg) dissolved in grain to form a slurry. Plasma enrofloxacin concentrations were measured by use of high-performance liquid chromatography. The multiple-dose regimen consisted of feeding a mixture of crushed and moistened enrofloxacin tablets mixed with grain. Behavior, appetite, and fecal quality were monitored throughout the 14-day treatment regimen and for 71 additional days following treatment. Mean half-life following i.v., s.c., and p.o. administration was 11.2, 8.7, and 16.1 hours, respectively. For s.c. and p.o administration, mean total systemic availability was 90.18% and 29.31%, respectively; mean maximum plasma concentration was 3.79 and 1.81 microg/mL, respectively; and area under the curve (AUC) was 50.05 and 33.97 (microg x h)/mL, respectively. The s.c. or p.o administration of a single dose of enrofloxacin yielded a ratio for AUC to minimum inhibitory concentration > 100 for many grampositive and gram-negative bacterial pathogens common to camelids. Conclusions and Clinical Relevance-The administration of enrofloxacin (5 mg/kg, s.c., or 10 mg/kg, p.o) may be appropriate for antimicrobial treatment of alpacas.

Syntheses, crystal structures and optical spectroscopy of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kazmierczak, Karolina; Hoeppe, Henning A., E-mail: henning@ak-hoeppe.d

2011-05-15

The lanthanide sulphate octahydrates Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and the respective tetrahydrate Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O were obtained by evaporation of aqueous reaction mixtures of trivalent rare earth oxides and sulphuric acid at 300 K. Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) crystallise in space group C2/c (Z=4, a{sub Ho}=13.4421(4) A, b{sub Ho}=6.6745(2) A, c{sub Ho}=18.1642(5) A, {beta}{sub Ho}=102.006(1) A{sup 3} and a{sub Tm}=13.4118(14) A, b{sub Tm}=6.6402(6) A, c{sub Tm}=18.1040(16) A, {beta}{sub Tm}=101.980(8) A{sup 3}), Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O adopts space group P2{sub 1}/n (a=13.051(3) A, b=7.2047(14) A, c=13.316(3) A, {beta}=92.55(3) A{sup 3}). The vibrationalmore » and optical spectra of Ho{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O are also reported. -- Graphical abstract: In the lanthanide sulphate octahydrates the cations form slightly undulated layers. Between the layers are voids in which sulphate tetrahedra and water molecules are located. The holmium compound exhibits an Alexandrite effect. Display Omitted Highlights: {yields} Determination of the optimum conditions for the growth of single-crystals of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O. {yields} Single-crystal structure elucidation of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) including hydrogen bonds. {yields} Single-crystal structure determination of Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O including hydrogen bonds. {yields} UV-vis spectra of Ho{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O recorded and interpreted: Assignation of bands and clarification of the Alexandrite effect of the Ho compound. {yields} IR and Raman spectra of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O recorded and interpreted.« less

Aquatic plant-derived changes in oil sands naphthenic acid signatures determined by low-, high- and ultrahigh-resolution mass spectrometry.

PubMed

Headley, John V; Peru, Kerry M; Armstrong, Sarah A; Han, Xiumei; Martin, Jonathan W; Mapolelo, Mmilili M; Smith, Donald F; Rogers, Ryan P; Marshall, Alan G

2009-02-01

Mass spectrometry is a common tool for studying the fate of complex organic compound mixtures in oil sands processed water (OSPW), but a comparison of low-, high- ( approximately 10 000), and ultrahigh-resolution ( approximately 400 000) instrumentation for this purpose has not previously been made. High-resolution quadrupole time-of-flight mass spectrometry (QTOF MS) and ultrahigh-resolution Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS), with negative-ion electrospray ionization, provided evidence for the selective dissipation of components in OSPW. Dissipation of oil sands naphthenic acids (NAs with general formula C(n)H(2n+z)O(2) where n is the number of carbon atoms, and Z is zero or a negative even number describing the number of rings) was masked (by components such as fatty acids, O(3), O(5), O(6), O(7), SO(2), SO(3), SO(4), SO(5), SO(6), and NO(4) species) at low resolution (1000) when using a triple quadrupole mass spectrometer. Changes observed in the relative composition of components in OSPW appear to be due primarily to the presence of plants, specifically cattails (Typha latifolia) and their associated microorganisms. The observed dissipation included a range of heteratomic species containing O(2), O(3), O(4), and O(5), present in Athabasca oil sands acid extracts. For the heteratomic O(2) species, namely naphthenic acids, an interesting structural relationship suggests that low and high carbon number NAs are dissipated by the plants preferentially, with a minimum around C(14)/C(15). Other heteratomic species containing O(6), O(7), SO(2), SO(3), SO(4), SO(5), SO(6), and NO(4) appear to be relatively recalcitrant to the cattails and were not dissipated to the same extent in planted systems. Copyright 2009 John Wiley & Sons, Ltd.

Plasma Jet Interactions with Liquids in Partial Fulfillment of an NRL Karles Fellowship

DTIC Science & Technology

2015-11-30

water (DI H2O) as the reference solution, two concentrations of NaCl mixtures (0.6 Molar, and 1.0 Molar saturated NaCl), and three electroless solutions...by diffusion) to the bulk surface in net excess; that oxygen ions/radicals are being consumed from the bulk by an electrolysis path way; or that the

Two isotypic diphosphates LiM{sub 2}H{sub 3}(P{sub 2}O{sub 7}){sub 2} (M=Ni, Co) containing ferromagnetic zigzag MO{sub 6} chains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang Tao; Yang Sihai; Liao Fuhui

2008-06-15

Two new isotypic phosphates LiNi{sub 2}H{sub 3}(P{sub 2}O{sub 7}){sub 2} (1) and LiCo{sub 2}H{sub 3}(P{sub 2}O{sub 7}){sub 2} (2) have been hydrothermally synthesized and structurally characterized by the single-crystal X-ray diffraction technique. They crystallize in the monoclinic space group C2/c with the lattice: a=10.925(2) A, b=12.774(3) A, c=8.8833(18) A, {beta}=123.20(3){sup o} for 1 and a=10.999(2) A, b=12.863(3) A, c=8.9419(18) A, {beta}=123.00(3){sup o} for 2. The transition metal atoms are octahedrally coordinated, whereas the lithium and phosphorus atoms are all tetrahedrally coordinated. As the lithium-induced derivatives of MH{sub 2}P{sub 2}O{sub 7} (M=Ni, Co), 1 and 2 possess the same structure withmore » MH{sub 2}P{sub 2}O{sub 7} in terms of topology, comprising the MO{sub 6} zigzag chains and P{sub 2}O{sub 7} as the interchain groups. The magnetisms of 1 and 2 could be interpreted by adopting a quasi-one-dimensional (1D) zigzag chain model as that in their parent compounds: both 1 and 2 have ferromagnetic (FM) NiO{sub 6}/CoO{sub 6} chains; 1 shows a FM cluster glass behavior at low temperatures, which is originated from the possible antiferromagnetic (AFM) next-nearest-neighbour intrachain interactions; 2 shows a AFM ordering at T{sub N}=2.6 K and a metamagnetic transition at H{sub C}=4.2 kOe at 1.8 K. - Graphical abstract: LiNi{sub 2}H{sub 3}(P{sub 2}O{sub 7}){sub 2} (1) and LiCo{sub 2}H{sub 3}(P{sub 2}O{sub 7}){sub 2} (2) have been hydrothermally synthesized and structurally characterized. The MO{sub 6} octahedra share edges forming zigzag chains with P{sub 2}O{sub 7} as the interchain groups. Both of them are quasi-one-dimensional magnets and have ferromagnetic MO{sub 6} chains; 1 is a ferromagnet, whereas 2 is a metamagnet.« less

C=C bond cleavage on neutral VO3(V2O5)n clusters.

PubMed

Dong, Feng; Heinbuch, Scott; Xie, Yan; Bernstein, Elliot R; Rocca, Jorge J; Wang, Zhe-Chen; Ding, Xun-Lei; He, Sheng-Gui

2009-01-28

The reactions of neutral vanadium oxide clusters with alkenes (ethylene, propylene, 1-butene, and 1,3-butadiene) are investigated by experiments and density function theory (DFT) calculations. Single photon ionization through extreme ultraviolet radiation (EUV, 46.9 nm, 26.5 eV) is used to detect neutral cluster distributions and reaction products. In the experiments, we observe products (V(2)O(5))(n)VO(2)CH(2), (V(2)O(5))(n)VO(2)C(2)H(4), (V(2)O(5))(n)VO(2)C(3)H(4), and (V(2)O(5))(n)VO(2)C(3)H(6), for neural V(m)O(n) clusters in reactions with C(2)H(4), C(3)H(6), C(4)H(6), and C(4)H(8), respectively. The observation of these products indicates that the C=C bonds of alkenes can be broken on neutral oxygen rich vanadium oxide clusters with the general structure VO(3)(V(2)O(5))(n=0,1,2...). DFT calculations demonstrate that the reaction VO(3) + C(3)H(6) --> VO(2)C(2)H(4) + H(2)CO is thermodynamically favorable and overall barrierless at room temperature. They also provide a mechanistic explanation for the general reaction in which the C=C double bond of alkenes is broken on VO(3)(V(2)O(5))(n=0,1,2...) clusters. A catalytic cycle for alkene oxidation on vanadium oxide is suggested based on our experimental and theoretical investigations. The reactions of V(m)O(n) with C(6)H(6) and C(2)F(4) are also investigated by experiments. The products VO(2)(V(2)O(5))(n)C(6)H(4) are observed for dehydration reactions between V(m)O(n) clusters and C(6)H(6). No product is detected for V(m)O(n) clusters reacting with C(2)F(4). The mechanisms of the reactions between VO(3) and C(2)F(4)/C(6)H(6) are also investigated by calculations at the B3LYP/TZVP level.

Laboratory IR Studies and Astrophysical Implications of C2H2-Containing Binary Ices

NASA Technical Reports Server (NTRS)

Knez, C.; Moore, M.; Ferrante, R.; Hudson, R.

2012-01-01

Studies of molecular hot cores and protostellar environments have shown that the observed abundance of gas-phase acetylene (C2H2) cannot be matched by chemical models without the inclusion of C2H2 molecules subliming from icy grain mantles. Searches for infrared (IR) spectral features of solid-phase acetylene are under way, but few laboratory reference spectra of C2H2 in icy mixtures, which are needed for spectral fits to observational data, have been published. Here, we report a systematic study of the IR spectra of condensed-phase pure acetylene and acetylene in ices dominated by carbon monoxide (CO), carbon dioxide (CO2), methane (CH4), and water (H2O). We present new spectral data for these ices, including band positions and intrinsic band strengths. For each ice mixture and concentration, we also explore the dependence of acetylene's nu5-band position (743 cm-1, 13.46 micrometers) and FWHM on temperature. Our results show that the nu5 feature is much more cleanly resolved in ices dominated by non-polar and low-polarity molecules, specifically CO, CO2, and CH4, than in mixtures dominated by H2O-ice. We compare our laboratory ice spectra with observations of a quiescent region in Serpens.

Thermal Decomposition of Potential Ester Biofuels. Part I: Methyl Acetate and Methyl Butanoate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porterfield, Jessica P.; Bross, David H.; Ruscic, Branko

2017-06-09

Two methyl esters have been examined as models for the pyrolysis of biofuels. Dilute samples (0.06 - 0.13%) of methyl acetate (CH 3COOCH 3) and methyl butanoate (CH 3CH 2CH 2COOCH 3) were entrained in (He, Ar) carrier gas and decomposed in a set of flash-pyrolysis micro-reactors. The pyrolysis products resulting from the methyl esters were detected and identified by vacuum ultraviolet photoionization mass spectrometry. Complementary product identification was provided by matrix infrared absorption spectroscopy. Pyrolysis pressures in the pulsed micro-reactor were roughly 20 Torr and residence times through the reactors were approximately 25 - 150 µs. Reactor temperatures ofmore » 300 – 1600 K were explored. Decomposition of CH 3COOCH 3 commences at 1000 K and the initial products are (CH 2=C=O and CH 3OH). As the micro-reactor is heated to 1300 K, a mixture of (CH 2=C=O and CH 3OH, CH 3, CH 2=O, H, CO, CO 2) appears. The thermal cracking of CH 3CH 2CH 2COOCH 3 begins at 800 K with the formation of (CH 3CH 2CH=C=O, CH 3OH). By 1300 K, the pyrolysis of methyl butanoate yields a complex mixture of (CH 3CH 2CH=C=O, CH 3OH, CH 3, CH 2=O, CO, CO 2, CH 3CH=CH 2, CH 2CHCH 2, CH 2=C=CH 2, HCCCH 2, CH 2=C=C=O, CH 2=CH 2, HCΞCH, CH 2=C=O). Based on the results from the thermal cracking of methyl acetate and methyl butanoate, we predict several important decomposition channels for the pyrolysis of fatty acid methyl esters, R CH 2-COOCH 3. The lowest energy fragmentation will be a 4-center elimination of methanol to form the ketene, RCH=C=O. At higher temperatures, concerted fragmentation to radicals will ensue to produce a mixture of species: (RCH 2 + CO 2 + CH 3) and (RCH 2 + CO + CH 2=O + H). Thermal cracking of the β C-C bond of the methyl ester will generate the radicals (R and H) as well as CH 2=C=O + CH 2=O. The thermochemistry of methyl acetate and its fragmentation products have been obtained via the Active Thermochemical Tables (ATcT) approach, resulting in Δ fH 298(CH 3COOCH 3) = -98.7 ± 0.2 kcal mol -1, Δ fH 298(CH 3CO 2) = -45.7 ± 0.3 kcal mol -1, and Δ fH 298(COOCH 3) = -38.3 ± 0.4 kcal mol -1.« less

Crystal structures of (±)-(1SR,5SR,6SR,7SR,10SR,11SR,13RS,14SR)-13-hy-droxy-7-meth-oxy-meth-oxy-11,15,18,18-tetra-methyl-3-oxo-2,4-dioxa-tetra-cyclo-[12.3.1.0(1,5).0(6,11)]octa-dec-15-en-10-yl benzoate, its 13-epimer and 13-one derivative.

PubMed

Oishi, Takeshi; Fukaya, Keisuke; Yamaguchi, Yu; Sugai, Tomoya; Watanabe, Ami; Sato, Takaaki; Chida, Noritaka

2015-05-01

The title compounds, C29H38O8·0.25C5H12, (A), C29H38O8, (B), and C29H36O8, (C), are tetra-cyclic benzoates possessing a taxane skeleton with a fused dioxolane ring as the core structure. In the asymmetric unit of (A), there are two independent benzoate mol-ecules (A and A') and a half mol-ecule of solvent pentane disordered about an inversion center. The mol-ecular conformations of (A), (B) and (C) are similar except for the flexible meth-oxy-meth-oxy group. The cyclo-hexane, cyclo-hexene and central cyclo-octane rings adopt chair, half-chair and chair-chair (extended crown) forms, respectively. The dioxolane rings are essentially planar, while the dioxolane ring of A' is slightly twisted from the mean plane. In the crystal of (A), inter-molecular O-H⋯O, C-H⋯O and C-H⋯π inter-actions link the independent benzoates alternately, forming a chain structure. In the crystals of (B) and (C), mol-ecules are linked through O-H⋯O and C-H⋯π inter-actions, and C-H⋯O hydrogen bonds, respectively, into similar chains. Further, weak inter-molecular C-H⋯O inter-actions connect the chains into a three-dimensional network in (A) and a sheet in (B), whereas no other interactions are observed for (C).

Hole injection and dielectric breakdown in 6H-SiC and 4H-SiC metal-oxide-semiconductor structures during substrate electron injection via Fowler-Nordheim tunneling

NASA Astrophysics Data System (ADS)

Samanta, Piyas; Mandal, Krishna C.

2015-12-01

Hole injection into silicon dioxide (SiO2) films (8-40 nm thick) is investigated for the first time during substrate electron injection via Fowler-Nordheim (FN) tunneling in n-type 4H- and 6H-SiC (silicon carbide) based metal-oxide-semiconductor (MOS) structures at a wide range of temperatures (T) between 298 and 598 K and oxide electric fields Eox from 6 to 10 MV/cm. Holes are generated in heavily doped n-type polycrystalline silicon (n+ -polySi) gate serving as the anode as well as in the bulk silicon dioxide (SiO2) film via hot-electron initiated band-to-band ionization (BTBI). In absence of oxide trapped charges, it is shown that at a given temperature, the hole injection rates from either of the above two mechanisms are higher in n-4H-SiC MOS devices than those in n-6H-SiC MOS structures when compared at a given Eox and SiO2 thickness (tox). On the other hand, relative to n-4H-SiC devices, n-6H-SiC structures exhibit higher hole injection rates for a given tox during substrate electron injection at a given FN current density je,FN throughout the temperature range studied here. These two observations clearly reveal that the substrate material (n-6H-SiC and n-4H-SiC) dependencies on time-to-breakdown (tBD) or injected charge (electron) to breakdown (QBD) of the SiO2 film depend on the mode of FN injections (constant field/voltage and current) from the substrate which is further verified from the rigorous device simulation as well.

Modification of primordial ices by cosmic rays as simulated by cyclotron irradiation

NASA Technical Reports Server (NTRS)

Kaiser, R. I.; Roessler, K.

1992-01-01

Frozen CH4 and CH4/Ar mixtures closed into metal cuvettes and open to the vacuum were irradiated at 15 and 77 K with 10 - 20 MeV p and He-3(2+) ions in order to simulate the effect of cosmic rays on solid organic matter in space. Ices exposed to vacuum represent surfaces of icy systems whereas closed systems stand for bulk ices. The products were analyzed by MS, SEM, RBS, ERDA, H-1-NMR, HPLC, GC-MS, NEXAFS, and FT-IR. Volatile products consisted of a mixture of low molecular species, e.g., C2H2, C2H4, C2H6, and long linear aliphatic and olefinic compounds. The formation of polycyclic aromatic hydrocarbons (PAH's) and related species in solid CH4 is due to a multi-center reaction within one collision cascade and is governed by energy density effects with critical linear energy transfer values L(sub T) between 2 and 10 keV/micron. Open ices exhibit preferential hydrogen release resulting in an increased carbonization as compared to more hydrogen rich molecules protected inside large icy bodies.

Decomposition of toluene in a steady-state atmospheric-pressure glow discharge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trushkin, A. N.; Grushin, M. E.; Kochetov, I. V.

Results are presented from experimental studies of decomposition of toluene (C{sub 6}H{sub 5}CH{sub 3}) in a polluted air flow by means of a steady-state atmospheric pressure glow discharge at different water vapor contents in the working gas. The experimental results on the degree of C{sub 6}H{sub 5}CH{sub 3} removal are compared with the results of computer simulations conducted in the framework of the developed kinetic model of plasma chemical decomposition of toluene in the N{sub 2}: O{sub 2}: H{sub 2}O gas mixture. A substantial influence of the gas flow humidity on toluene decomposition in the atmospheric pressure glow discharge ismore » demonstrated. The main mechanisms of the influence of humidity on C{sub 6}H{sub 5}CH{sub 3} decomposition are determined. The existence of two stages in the process of toluene removal, which differ in their duration and the intensity of plasma chemical decomposition of C{sub 6}H{sub 5}CH{sub 3} is established. Based on the results of computer simulations, the composition of the products of plasma chemical reactions at the output of the reactor is analyzed as a function of the specific energy deposition and gas flow humidity. The existence of a catalytic cycle in which hydroxyl radical OH acts a catalyst and which substantially accelerates the recombination of oxygen atoms and suppression of ozone generation when the plasma-forming gas contains water vapor is established.« less

A role for solvents in the toxicity of agricultural organophosphorus pesticides

PubMed Central

Eddleston, Michael; Street, Jonathan M.; Self, Ian; Thompson, Adrian; King, Tim; Williams, Nicola; Naredo, Gregorio; Dissanayake, Kosala; Yu, Ly-Mee; Worek, Franz; John, Harald; Smith, Sionagh; Thiermann, Horst; Harris, John B.; Eddie Clutton, R.

2012-01-01

Organophosphorus (OP) insecticide self-poisoning is responsible for about one-quarter of global suicides. Treatment focuses on the fact that OP compounds inhibit acetylcholinesterase (AChE); however, AChE-reactivating drugs do not benefit poisoned humans. We therefore studied the role of solvent coformulants in OP toxicity in a novel minipig model of agricultural OP poisoning. Gottingen minipigs were orally poisoned with clinically relevant doses of agricultural emulsifiable concentrate (EC) dimethoate, dimethoate active ingredient (AI) alone, or solvents. Cardiorespiratory physiology and neuromuscular (NMJ) function, blood AChE activity, and arterial lactate concentration were monitored for 12 h to assess poisoning severity. Poisoning with agricultural dimethoate EC40, but not saline, caused respiratory arrest within 30 min, severe distributive shock and NMJ dysfunction, that was similar to human poisoning. Mean arterial lactate rose to 15.6 [SD 2.8] mM in poisoned pigs compared to 1.4 [0.4] in controls. Moderate toxicity resulted from poisoning with dimethoate AI alone, or the major solvent cyclohexanone. Combining dimethoate with cyclohexanone reproduced severe poisoning characteristic of agricultural dimethoate EC poisoning. A formulation without cyclohexanone showed less mammalian toxicity. These results indicate that solvents play a crucial role in dimethoate toxicity. Regulatory assessment of pesticide toxicity should include solvents as well as the AIs which currently dominate the assessment. Reformulation of OP insecticides to ensure that the agricultural product has lower mammalian toxicity could result in fewer deaths after suicidal ingestion and rapidly reduce global suicide rates. PMID:22365945

Dual Functional Core-Shell Fluorescent Ag2S@Carbon Nanostructure for Selective Assay of E. coli O157:H7 and Bactericidal Treatment.

PubMed

Wang, Ning; Wei, Xing; Zheng, An-Qi; Yang, Ting; Chen, Ming-Li; Wang, Jian-Hua

2017-03-24

A dual functional fluorescent core-shell Ag 2 S@Carbon nanostructure is prepared by a hydrothermally assisted multi-amino synthesis approach with folic acid (FA), polyethylenimine (PEI), and mannoses (Mans) as carbon and nitrogen sources (FA-PEI-Mans-Ag 2 S nanocomposite shortly as Ag 2 S@C). The nanostructure exhibits strong fluorescent emission at λ ex /λ em = 340/450 nm with a quantum yield of 12.57 ± 0.52%. Ag 2 S@C is bound to E. coli O157:H7 via strong interaction with the Mans moiety in Ag 2 S@C with FimH proteins on the fimbriae tip in E. coli O157:H7. Fluorescence emission from Ag 2 S@C/E. coli conjugate is closely related to the content of E. coli O157:H7. Thus, a novel procedure for fluorescence assay of E. coli O157:H7 is developed, offering a detection limit of 330 cfu mL -1 . Meanwhile, the Ag 2 S@C nanostructure exhibits excellent antibacterial performance against E. coli O157:H7. A 99.9% sterilization rate can be readily achieved for E. coli O157:H7 at a concentration of 10 6 -10 7 cfu mL -1 with 3.3 or 10 μg mL -1 of Ag 2 S@C with an interaction time of 5 or 0.5 min, respectively.

Promotional effects of chemisorbed oxygen and hydroxide in the activation of C-H and O-H bonds over transition metal surfaces

NASA Astrophysics Data System (ADS)

Hibbitts, David; Neurock, Matthew

2016-08-01

Electronegative coadsorbates such as atomic oxygen (O*) and hydroxide (OH*) can act as Brønsted bases when bound to Group 11 as well as particular Group 8-10 metal surfaces and aid in the activation of X-H bonds. First-principle density functional theory calculations were carried out to systematically explore the reactivity of the C-H bonds of methane and surface methyl intermediates as well as the O-H bond of methanol directly and with the assistance of coadsorbed O* and OH* intermediates over Group 11 (Cu, Ag, and Au) and Group 8-10 transition metal (Ru, Rh, Pd, Os, Ir, and Pt) surfaces. C-H as well as O-H bond activation over the metal proceeds via a classic oxidative addition type mechanism involving the insertion of the metal center into the C-H or O-H bond. O* and OH* assist C-H and O-H activation over particular Group 11 and Group 8-10 metal surfaces via a σ-bond metathesis type mechanism involving the oxidative addition of the C-H or O-H bond to the metal along with a reductive deprotonation of the acidic C-H and O-H bond over the M-O* or M-OH* site pair. The O*- and OH*-assisted C-H activation paths are energetically preferred over the direct metal catalyzed C-H scission for all Group 11 metals (Cu, Ag, and Au) with barriers that are 0.4-1.5 eV lower than those for the unassisted routes. The barriers for O*- and OH*-assisted C-H activation of CH4 on the Group 8-10 transition metals, however, are higher than those over the bare transition metal surfaces by as much as 1.4 eV. The C-H activation of adsorbed methyl species show very similar trends to those for CH4 despite the differences in structure between the weakly bound methane and the covalently adsorbed methyl intermediates. The activation of the O-H bond of methanol is significantly promoted by O* as well as OH* intermediates over both the Group 11 metals (Cu, Ag, and Au) as well as on all Group 8-10 metals studied (Ru, Rh, Pd, Os, Ir, and Pt). The O*- and OH*-assisted CH3O-H barriers are 0.6 to 2.0 eV lower than unassisted barriers, with the largest differences occurring on Group 11 metals. The higher degree of O*- and OH*-promotion in activating methanol over that in methane and methyl is due to the stronger interaction between the basic O* and OH* sites and the acidic proton in the O-H bond of methanol versus the non-acidic H in the C-H bond of methane. A detailed analysis of the binding energies and the charges for O* and OH* on different metal surfaces indicates that the marked differences in the properties and reactivity of O* and OH* between the Group 11 and Group 8-10 metals is due to the increased negative charge on the O-atoms (in O* as well as OH*) bound to Group 11 metals. The promotional effects of O* and OH* are consistent with a proton-coupled electron transfer and the cooperative role of the metal-O* or metal-OH* pair in carrying out the oxidative addition and reductive deprotonation of the acidic C-H and O-H bonds. Ultimately, the ability of O* or OH* to act as a Brønsted base depends upon its charge, its binding energy on the metal surface (due to shifts in its position during X-H activation), and the acidity of the H-atom being abstracted.

A V(IV) Hydroxyhydrogenomonophosphate with an Intersecting Tunnel Structure: HK 4[V 10O 10(H 2O) 2(OH) 4(PO 4) 7]·9H 2O

NASA Astrophysics Data System (ADS)

Berrah, F.; Guesdon, A.; Leclaire, A.; Borel, M. M.; Provost, J.; Raveau, B.

1999-12-01

A V(IV) hydroxyhydrogenomonophosphate HK4[V10O10(H2O)2(OH)4(PO4)7]·9H2O has been obtained, using hydrothermal conditions. Its structure, closely related to that of (CH3)2NH2K4[V10O10(H2O)2(OH)4(PO4)7]·4H2O, differs from the latter by its I41/a space group (instead of P43). This difference corresponds to a "disordering" of the vanadium atoms, with respect to the dimethyl ammonium phase. It is shown that this disorder, which appears in the form of "V5O22" units distributed at random, does not affect the oxygen framework. The analysis of this complex structure shows that it can be described from the stacking along c of [V8P7O38(OH)4(H2O)2]∞ layers interconnected through layers of isolated VO6 octahedra. In this structure, built up of VO6, VO5OH, and VO4(OH)(H2O) octahedra, of VO4OH pyramids, and of PO4 tetrahedra, large "toffee" tunnels and smaller ones with a tulip-shape section are running along a (or b). The first ones are stuffed with H2O molecules forming aquo tubes, where protons are likely "delocalized," whereas the second ones are occupied by K+ cations.

Infrared predissociation spectroscopy of M+ (C6H6)(1-4)(H2O)(1-2)Ar(0-1) cluster ions, M = Li, Na.

PubMed

Beck, Jordan P; Lisy, James M

2011-05-05

Infrared predissociation (IRPD) spectra of Li(+)(C(6)H(6))(1-4)(H(2)O)(1-2)Ar(0-1) and Na(+)(C(6)H(6))(2-4)(H(2)O)(1-2)Ar(1) are presented along with ab initio calculations. The results indicate that the global minimum energy structure for Li(+)(C(6)H(6))(2)(H(2)O)(2) has each water forming a π-hydrogen bond with the same benzene molecule. This bonding motif is preserved in Li(+)(C(6)H(6))(3-4)(H(2)O)(2)Ar(0-1) with the additional benzene ligands binding to the available free OH groups. Argon tagging allows high-energy Li(+)(C(6)H(6))(2-4)(H(2)O)(2)Ar isomers containing water-water hydrogen bonds to be trapped and detected. The monohydrated, Li(+) containing clusters contain benzene-water interactions with varying strength as indicated by shifts in OH stretching frequencies. The IRPD spectra of M(+)(C(6)H(6))(1-4)(H(2)O)(1-2)Ar are very different for lithium-bearing versus sodium-bearing cluster ions emphasizing the important role of ion size in determining the most favorable balance of competing noncovalent interactions.

Energetics of CO2 and H2O adsorption on zinc oxide.

PubMed

Gouvêa, Douglas; Ushakov, Sergey V; Navrotsky, Alexandra

2014-08-05

Adsorption of H2O and CO2 on zinc oxide surfaces was studied by gas adsorption calorimetry on nanocrystalline samples prepared by laser evaporation in oxygen to minimize surface impurities and degassed at 450 °C. Differential enthalpies of H2O and CO2 chemisorption are in the range -150 ±10 kJ/mol and -110 ±10 kJ/mol up to a coverage of 2 molecules per nm(2). Integral enthalpy of chemisorption for H2O is -96.8 ±2.5 kJ/mol at 5.6 H2O/nm(2) when enthalpy of water condensation is reached, and for CO2 is -96.6 ±2.5 kJ/mol at 2.6 CO2/nm(2) when adsorption ceases. These values are consistent with those reported for ZnO prepared by other methods after similar degas conditions. The similar energetics suggests possible competition of CO2 and H2O for binding to ZnO surfaces. Exposure of bulk and nanocrystalline ZnO with preadsorbed CO2 to water vapor results in partial displacement of CO2 by H2O. In contrast, temperature-programmed desorption (TPD) indicates that a small fraction of CO2 is retained on ZnO surfaces up to 800 °C, under conditions where all H2O is desorbed, with adsorption energies near -200 kJ/mol. Although molecular mechanisms of adsorption were not studied, the thermodynamic data are consistent with dissociative adsorption of H2O at low coverage and with several different modes of CO2 binding.