Cyclic fatigue of ProTaper instruments.

PubMed

Lopes, Hélio Pereira; Moreira, Edson Jorge Lima; Elias, Carlos Nelson; de Almeida, Renata Andriola; Neves, Mônica Schultz

2007-01-01

The present work evaluated the influence of the curved segment length of artificial root canals (the arc) and the number of cycles necessary to fracture engine-driven nickel-titanium endodontic instruments. ProTaper F3 25-mm files at 250 rpm were used in two artificial canals. The artificial canals were made of stainless steel with an inner diameter of 1.04 mm, a total length of 20 mm, and arc on the ends with a radius of curvature of 6 mm. The arc length of the first tube measured 9.4 mm, and the straight part measured 10.6 mm. The second tube was 14.1 mm long, and the straight part measured 5.9 mm. We determined the fracture surface distances and the number of cycles necessary to induce fatigue fracture in the ProTaper F3 instruments. The fracture surfaces and the helical shaft of the instruments were investigated using a scanning electron microscope. The results indicated that the required number of cycles to cause a fracture was influenced by the canal arc length, the morphology of the fractured surface presented ductile characteristics, and plastic deformation in the helical shaft of the fractured instruments did not occur.

Age and growth of pike (Esox lucius) in Chivyrkui Bay, Lake Baikal

USGS Publications Warehouse

Owens, Randall W.; Pronin, Nikolai M.

2000-01-01

The purpose of this study was to describe age and growth of pike (Esox lucius) in Lake Baikal. Pike were collected with gill nets and by angling in Chivyrkui Bay in late July-early August 1993 and by gill nets in June 1995. Total length (mm), weight (g), and sex were recorded and scales and cleithra were collected for aging. In 1993, pike, ages 1 to 3, ranged in length from 331 to 810 mm and in 1995 , pike, ages 2 to 10, ranged in length from 365 to 1,111 mm but only three percent were age 7 or older. Most growth in length occurred during the first two years of life. The length-weight relation for pike from Chivyrkui Bay was similar to that of pike from the St. Lawrence River. Calculated total length of pike from Lake Baikal equalled or exceeded the lengths of pike from lakes Erie or Ontario. Good agreement was found between ages from cleithra and from scales. Lengths at age in June 1995 (N=108) varied widely among pike. Females were generally larger than males at a given age among fish age-3 and older. When compared with the circumpolar growth standard, based on the von Bertalanffy growth curve, growth of Lake Baikal pike exceeded all other Asian populations, and equalled or exceeded many other northern hemisphere populations.

In vivo evaluation of axial integrity of coronary stents using intravascular ultrasound: Insights on longitudinal stent deformation.

PubMed

Dvir, Danny; Kitabata, Hironori; Barbash, Israel M; Minha, Sa'ar; Badr, Salem; Loh, Joshua P; Chen, Fang; Torguson, Rebecca; Waksman, Ron

2014-09-01

To evaluate the axial integrity of different coronary stents using intravascular ultrasound (IVUS). Longitudinal stent deformation was recently reported. Consecutive patients who underwent IVUS analysis after drug-eluting stent (DES) implantation for de novo coronary lesions were evaluated. Stent length was compared with label length for calculation of absolute change and relative difference (absolute change divided by label length). A total of 233 DES utilizing five different platforms were included. The median absolute change in stent length was 0.90 mm (interquartile range [IQR] 0.48-1.39) and the relative difference was 5.24% (IQR 2.55-8.29). There was no significant difference among the groups in median absolute or relative change: Cypher 0.89 mm/3.89%, Taxus 0.88 mm/5.39%, Endeavor 1.16 mm/6.77%, Xience V 0.86 mm/5.80%, and PROMUS Element 0.79 mm/5.34% (P = 0.085, P = 0.072, respectively). Multivariate logistic regression revealed that the Cypher stent was independently correlated with a lower change in length, whereas stent label length and deployment pressure were correlated with higher absolute change. The axial integrity of DES platforms examined in vivo was high, with only mild changes in stent length after implantation. While there are differences between first- and second-generation DES, axial integrity among second-generation DES was similar. © 2013 Wiley Periodicals, Inc.

The total body length and body weight examination among gabus Sentani fish population, Oxyeleotris heterodon, Weber 1907 (Pisces: Eleotridae) of Sentani lake, Papua, Indonesia

NASA Astrophysics Data System (ADS)

Sriyani, E. D.; Abinawanto, Bowolaksono, A.

2017-07-01

The gabus Sentani fish lived in the Sentani Lake, Papua, since million years ago. Nowadays, the population of those species is getting extinct because of the overexploitation, whereas the culture effort of this species has not been developed, yet. The purpose of the study was to examine the total body length and body weight collected from some villages surrounding Sentani Lake such as Ifar village, Sosiri village, and Putali village. The body weight average of gabus fish from Ifar village, Sosiri village, and Putali village were 373.53 g, 426.86 g, and 118.34 g respectively. While the total body length average of gabus Sentani fish from Ifar village, Sosiri village, and Putali village were 279.30 mm, 223.30 mm and 222.06 mm, respectively. The growth model was W = 0.021067L3.086 with R2 value was 35.8 %, and r value was 0.598. Gabus Sentani fish, Oxyeleotris heterodon (Weber 1907) exhibited positive allometric (b > 3).

Trunnionosis: Does Head Size Affect Fretting and Corrosion in Total Hip Arthroplasty?

PubMed

Del Balso, Christopher; Teeter, Matthew G; Tan, Sok Chuen; Howard, James L; Lanting, Brent A

2016-10-01

Wear and tribocorrosion at the modular head-neck taper interface may be a cause of failure in metal-on-polyethylene total hip arthroplasty (THA). The present investigation endeavored to elucidate the effect of femoral head diameter on fretting and corrosion in retrieved head-neck tapers. A retrieval analysis of THA prostheses in vivo for a minimum of 1 year was performed. Twenty-three femoral heads of 32-mm diameter were matched with 28-mm heads based on time in vivo and head length (-3 mm to +8 mm). All included implants featured a single taper design from a single manufacturer. Fretting and corrosion damage scoring was performed for each implant under stereomicroscopic visualization. Head diameter was observed to affect fretting (P = .01), with 32-mm femoral heads exhibiting greater total fretting scores than 28-mm heads. Fretting damage was greatest (P = .01) in the central concentric zone of the femoral head bore tapers, regardless of head diameter, length, or stem offset. No significant effect on total corrosion scores was observed for any head or stem variable. Retrieved implant total corrosion scores were positively correlated (ρ = 0.51, P < .001) with implantation time. Increased femoral head diameter in THA may produce greater fretting damage owing to and increased head-neck moment arm. There is no associated increase in corrosion with 28-mm and 32-mm heads of this taper design. The longer a THA prosthesis is implanted, the greater the risk of damage due to corrosion. Copyright © 2016 Elsevier Inc. All rights reserved.

Usefulness of intraoperative radiographs in reducing errors of cup placement and leg length during total hip arthroplasty.

PubMed

Wind, Michael A; Morrison, J Craig; Christie, Michael J

2013-11-01

Traditional methods of component placement during total hip arthroplasty (THA) can lead to errors in cup abduction angle and leg length. Intraoperative radiographs were used to assess and correct errors during surgery in a consecutive series of 278 THAs performed by a single surgeon. After exclusions, 262 cases were available for cup abduction angle assessment and 224 for leg length discrepancy (LLD) assessment. Components were initially placed in a position determined as appropriate by the surgeon. Intraoperative radiographs were taken and appropriate corrections made. Postoperative radiographs were assessed at 6 weeks. Mean abduction angle on intraoperative radiographs was 39.6°±5.9° versus 38.6°±4.1° on postoperative radiographs. Thirty-eight cups were outside the target abduction range on intraoperative radiographs versus 4 on postoperative radiographs. Mean LLD was 3.7 mm ± 3.6 mm on intraoperative radiographs and 2.5 mm ± 2.7 mm on postoperative radiographs. Use of intraoperative radiographs is a valid, useful technique for minimizing errors in THA.

Optimal screw placement for base plate fixation in reverse total shoulder arthroplasty.

PubMed

DiStefano, James Guido; Park, Andrew Y; Nguyen, Thuc-Quyen D; Diederichs, Gerd; Buckley, Jenni M; Montgomery, William H

2011-04-01

Scapular cortical thickness has not been fully characterized from the perspective of determining optimal screw placement for securing the glenoid base plate in reverse shoulder arthroplasty. Twelve fresh frozen cadaveric scapulae underwent high resolution CT scans with 3-dimensional reconstructions and wall thickness analysis. Digital base plates were positioned and virtual screws were placed according to 2 scenarios: A - intraosseous through the entire course and exits a "safe region" with no known neurovascular structures; B - may leave and re-enter the bone and penetrates the thickest cortical region accessible regardless of adjacent structures. For scenario A, the optimal screw configurations were: (superior screw) length = 35 mm, 9° superior, 2° posterior; (inferior screw-A) length = 34 mm, 16° inferior, 5° anterior; (inferior screw-B) length = 31 mm, 31 inferior, 4 posterior; (posterior screw) length 19 mm, 29° inferior, 3° anterior. For scenario B: (superior screw) length = 36 mm, 28° superior, 10° anterior; (inferior screw) length = 35 mm, 19° inferior, 4° anterior; (posterior screw) length 37 mm, 23° superior, 3° anterior. The anterior screw was consistent between scenarios A and B, averaged 29 mm in length and was directed 16° inferior and 14° posterior. Thicker cortical regions were present in the lateral aspect of the suprascapular notch, scapular spine base, anterior/superior aspect of inferior pillar and junction of glenoid neck and scapular spine. Regions with high cortical thickness were accessible for both scenarios except for the posterior screw in scenario A. Copyright © 2011 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Mosby, Inc. All rights reserved.

Stipe Length as an Indicator of Reproductive Maturity in the Kelp Ecklonia cava

NASA Astrophysics Data System (ADS)

Kim, Sangil; Youn, Suk Hyun; Oh, Hyun-Ju; Choi, Sun Kyeong; Kang, Yun Hee; Kim, Tae-Hoon; Lee, Hyuk Je; Choi, Kwang-Sik; Park, Sang Rul

2018-05-01

We conducted testing to determine whether stipe length is a useful indicator of reproductive maturity in the kelp Ecklonia cava, a species that plays a pivotal role in ecosystem functioning and services in subtidal areas. Approximately 100 sporophytes with stipes of various lengths were collected during the fertile period (July-November, 2013). We investigated the relationships between stipe length and other morphological characteristics to determine whether stipe length could indicate the age of reproductive maturity. Primary blade length, longest blade length, thallus height, and total length showed significant relationships with stipe length. The length of the primary and longest blades gradually declined as stipe length increased above 125 mm. Zoosporangial sori were found on the blades of more than 70% of individuals with stipes longer than 125 mm, but on only 8% of individuals with stipes less than 125 mm long. Stipe length therefore seems to be an acceptable proxy for reproductive maturity. Another factor to consider, however, is that all specimens with zoosporangial sori, regardless of stipe length, had a dry weight of 80 g or more; thus, individual biomass may also be an important parameter influencing the initiation of reproduction.

Evaluation of root and alveolar bone development of unilateral osseous impacted immature maxillary central incisors after the closed-eruption technique.

PubMed

Shi, Xiangru; Xie, Xiaoyan; Quan, Junkang; Wang, Xiaozhe; Sun, Xiangyu; Zhang, Chenying; Zheng, Shuguo

2015-10-01

In this study, we evaluated root and alveolar bone development in unilateral osseous impacted immature maxillary central incisors by cone-beam computed tomography before and after closed-eruption treatment, in comparison with naturally erupted contralateral immature maxillary central incisors. The study included 30 patients, 20 boys and 10 girls, with a mean age of 8.44 ± 1.20 years (range, 6.5-11.2 years). After treatment, the root lengths of both the impacted maxillary central incisors (10.66 ± 2.10 mm) and the contralateral maxillary central incisors (11.04 ± 1.76 mm) were significantly greater than their pretreatment values (6.67 ± 1.94 and 9.02 ± 2.13 mm, respectively). The root canal widths of the incisors decreased significantly after treatment. From the posttreatment cone-beam computed tomography images, the ratio of exposed root length to total root length and the thickness of the alveolar bone at 1 mm under the alveolar crest and at the apex were calculated to evaluate alveolar bone development. Impacted immature maxillary central incisors differed significantly from contralateral immature maxillary central incisors in labial exposed root length, labial ratio to total root length, and lingual alveolar crest. Clinical crown height was higher (statistically but not clinically) for the impacted incisors (9.87 mm) than for the contralateral incisors (9.37 mm). Impacted immature incisors grew to the same stage as did erupted contralateral incisors after closed-eruption treatment. Both incisor types had some alveolar bone loss, and thin alveolar bone surrounded the roots. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Can Arthroplasty Stem INfluence Outcome? (CASINO): a randomized controlled equivalence trial of 125 mm versus 150 mm Exeter V40 stems in total hip arthroplasty.

PubMed

Hamilton, David F; Ohly, Nicholas E; Gaston, Paul

2018-04-16

The use of shorter length femoral stems during total hip arthroplasty has been suggested to accommodate wider patient femoral geometry and offer maximal bone preservation. However, cemented short-stem designs may increase the risk of varus stem malalignment and influence patient outcomes. CASINO is a multi-centre randomised equivalence trial that will recruit 220 patients undergoing total hip arthroplasty for osteoarthritis at two NHS hospitals in Scotland. Patients will be aged 45-80, undergoing unilateral primary hip arthroplasty, with no plan for contralateral procedure within the study timeframe, and able to comply with the protocol. Participants will be randomised to receive either a short (125 mm) or a standard (150 mm) Exeter V40 stem. The Contemporary acetabular component will be used in all cases. All implants will be cemented. Patient pain, function and satisfaction will be assessed using change from baseline measurement in Oxford Hip Score, Forgotten Joint Score, EQ-5D, pain numerical rating scores, and patient satisfaction questionnaire at baseline and at 1 and 2 years following surgery. Radiographic assessment will evaluate stem position and will be appraised by independent reviewers. Patients will be blind to implant allocation. Stem length may be associated with outcome; however, we can find no randomised trial in which researchers investigated the effect of stem length on patient outcome following cemented total hip arthroplasty. The aim of this trial is to determine if the use of short cemented stems offers equivalent patient outcomes to those achieved following surgery with standard length stems. International Standard Randomised Controlled Trial Number, ISRCTN13154542 , Registered on 30 June 2017.

Components of height and blood pressure in childhood

PubMed Central

Regnault, Nolwenn; Kleinman, Ken P; Rifas-Shiman, Sheryl L; Langenberg, Claudia; Lipshultz, Steven E; Gillman, Matthew W

2014-01-01

Background In children being taller is associated with higher blood pressure (BP), but few studies have divided height into its components: trunk and leg length. We examined the associations of total height, trunk length and leg length with systolic BP (SBP), diastolic BP (DBP) and pulse pressure (PP) at early childhood and mid-childhood visits, as well as change between the two visits. Methods We obtained five measures of SBP and DBP at the early childhood visit (N = 1153, follow-up rate = 54%) and at the mid-childhood visit (N = 1086, follow-up rate = 51%) respectively, in Project Viva, a US cohort study. We measured total height and sitting height (a measure of trunk length that includes head and neck) and calculated leg length as the difference between the two. Using mixed models, we adjusted the cross-sectional analyses for leg length when trunk length was the exposure of interest, and vice versa. We also adjusted for maternal race/ethnicity, child age, sex, overall adiposity and BP measurement conditions. Results At the mid-childhood visit, total height was positively associated with SBP [0.34 (0.24; 0.45) mmHg/cm] but not with DBP [0.07 (−0.003; 0.15)]. In models examining trunk and leg length separately, each was positively associated with SBP [0.72 (0.52; 0.92) and 0.33 (0.16; 0.49) respectively]. In a fully adjusted model with both leg and trunk length, only trunk length remained associated with BP. For a given leg length, a 1-cm increment in trunk length was associated with a 0.63-mmHg (0.42; 0.83) higher SBP and a 0.17-mmHg (0.02; 0.31) higher DBP. For a given trunk length, however, the associations of leg length with SBP [0.13 (−0.03; 0.30)] and with DBP [0.002 (−0.11; 0.12)] were null. These patterns were similar at the early childhood visit. Conclusions Children with greater trunk lengths have higher BPs, perhaps because of the additional pressure needed to overcome gravity to perfuse the brain. PMID:24413933

[Magnetic resonance imaging study of effects of accommodation on human lens morphological characters].

PubMed

Zheng, Sui-lian; Zhang, Ai; Shi, Jian-jing; Zhou, Yun-xin

2013-11-05

To evaluate the effects of accommodation on lens morphological characters. From January 2011 to June 2011, magnetic resonance images of eyes were acquired from 30 subjects aged 20 to 24 years during accommodation and at rest. The optimal images were analyzed by Autocad 2010 to obtain the total lens cross-sectional area (CSA) and CSA of anterior and posterior portions of lens, anterior chamber depth, lens thickness, lens diameter, vitreous chamber depth and axial length during accommodation and at rest. Paired-t test was performed. The anterior curvature radius (mm), posterior curvature radius (mm), CSA of anterior portion (mm(2)), CSA of posterior portion (mm(2)), total lens CSA (mm(2)) was (8.7 ± 0.8), (6.2 ± 0.5), (7.5 ± 2.1), (12.0 ± 2.6), (20 ± 4) during relaxed accommodation; anterior curvature radius (mm), posterior curvature radius (mm), CSA of anterior portion (mm(2)), CSA of posterior portion (mm(2)), total lens CSA (mm(2)) was (7.1 ± 1.3), (5.6 ± 0.5), (14.7 ± 2.9), (12.2 ± 2.1) and (27 ± 4) during accommodation. The total lens CSA (t = -11.556, P < 0.01) and CSA of anterior portion (t = -15.653, P < 0.01) both increased in accommodative states. The CSA of posterior portion of lens (t = -0.437, P > 0.05) under a statistically independent accommodative state. There was significant difference in the anterior chamber depth (t = 4.366, P < 0.01), lens thickness (t = -5.456, P < 0.01) and lens diameter (t = 4.597, P < 0.01) in accommodative states. There were insignificant differences both in vitreous chamber depth (t = 0.428, P > 0.05) and axial length (t = 0.418, P > 0.05) under accommodative states. During accommodation, the anterior chamber depth decreases, lens thickness increases and diameter of lens decreases while anterior portions and total lens CSA increase. There are insignificant changes in posterior portions of lens CSA, vitreous chamber depth and axial length. The accommodative changes in CSA indicate that the anterior portion of lens may be related with the properties of anterior capsule and lens material, the position of zonular attachments and the location of fetal nucleus. Helmholtz theory is supported.

Techniques for small-bone lengthening in congenital anomalies of the hand and foot.

PubMed

Minguella, J; Cabrera, M; Escolá, J

2001-10-01

The purpose of this study is to analyse three different lengthening techniques used in 31 small bones for congenital malformations of the hand and foot: 15 metacarpals, 12 metatarsals, 1 foot stump and 3 spaces between a previously transplanted phalanx end of the carpus or the metacarpal. Progressive lengthening with an external fixator device was performed in 23 cases: the callus distraction (callotasis) technique was used in 15 cases, whereas in the other 8 cases the speed of lengthening was faster and the defect bridged with a bone graft as a second stage. In another eight cases, a one-stage lengthening was performed. In the callotasis group, the total length gained ranged from 9 mm to 30 mm and the percentage of lengthening obtained (compared with the initial bone length) averaged 53.4%; in the fast lengthening group, the length gained ranged from 8 mm to 15 mm, and the average percentage of lengthening was 53.1%; and in the one-stage group, the length gained ranged from 7 mm to 15 mm, and the average percentage of lengthening was 43%. The overall complication rate was 22.5%.

Age structure and mortality of walleyes in Kansas reservoirs: Use of mortality caps to establish realistic management objectives

USGS Publications Warehouse

Quist, M.C.; Stephen, J.L.; Guy, C.S.; Schultz, R.D.

2004-01-01

Age structure, total annual mortality, and mortality caps (maximum mortality thresholds established by managers) were investigated for walleye Sander vitreus (formerly Stizostedion vitreum) populations sampled from eight Kansas reservoirs during 1991-1999. We assessed age structure by examining the relative frequency of different ages in the population; total annual mortality of age-2 and older walleyes was estimated by use of a weighted catch curve. To evaluate the utility of mortality caps, we modeled threshold values of mortality by varying growth rates and management objectives. Estimated mortality thresholds were then compared with observed growth and mortality rates. The maximum age of walleyes varied from 5 to 11 years across reservoirs. Age structure was dominated (???72%) by walleyes age 3 and younger in all reservoirs, corresponding to ages that were not yet vulnerable to harvest. Total annual mortality rates varied from 40.7% to 59.5% across reservoirs and averaged 51.1% overall (SE = 2.3). Analysis of mortality caps indicated that a management objective of 500 mm for the mean length of walleyes harvested by anglers was realistic for all reservoirs with a 457-mm minimum length limit but not for those with a 381-mm minimum length limit. For a 500-mm mean length objective to be realized for reservoirs with a 381-mm length limit, managers must either reduce mortality rates (e.g., through restrictive harvest regulations) or increase growth of walleyes. When the assumed objective was to maintain the mean length of harvested walleyes at current levels, the observed annual mortality rates were below the mortality cap for all reservoirs except one. Mortality caps also provided insight on management objectives expressed in terms of proportional stock density (PSD). Results indicated that a PSD objective of 20-40 was realistic for most reservoirs. This study provides important walleye mortality information that can be used for monitoring or for inclusion into population models; these results can also be combined with those of other studies to investigate large-scale differences in walleye mortality. Our analysis illustrates the utility of mortality caps for monitoring walleye populations and for establishing realistic management goals.

Proposed standard-weight equations for brook trout

USGS Publications Warehouse

Hyatt, M.W.; Hubert, W.A.

2001-01-01

Weight and length data were obtained for 113 populations of brook trout Salvelinus fontinalis across the species' geographic range in North America to estimate a standard-weight (Ws) equation for this species. Estimation was done by applying the regression-line-percentile technique to fish of 120-620 mm total length (TL). The proposed metric-unit (g and mm) equation is log10Ws = -5.186 + 3.103 log10TL; the English-unit (lb and in) equivalent is log10Ws = -3.483 + 3.103 log10TL. No systematic length bias was evident in the relative-weight values calculated from these equations.

Implication of forage particle length on chewing activities and milk production in dairy goats.

PubMed

Lu, C D

1987-07-01

Twenty-four primiparous Alpine does fed a high concentrate ration were utilized to study the effect of forage particle length on chewing activity, ruminal components, and milk composition. Treatments were Bermudagrass hay with mean particle length of 2.38 and 3.87 mm. Forage particle length was determined with an oscillating screen particle separator. Feeding forage with 3.87-mm mean particle length to lactating dairy goats resulted in higher total chewing and rumination times, slightly higher milk fat content, and fat-corrected milk production. Results from this experiment support the hypothesis that forage particle length affects chewing activities and production of milk fat precursors in the rumen and alters milk fat content and output of fat-corrected milk. Forage particle length appeared to be an important index for forage quality and a quantitative approach could be feasible to establish a system relating forage particle length to milk production in dairy goats.

Second trimester fetal nasal bone length in a low-risk Turkish population.

PubMed

Yanik, Filiz Fatma; Eroglu, Derya; Baser, Eralp; Dursun, Polat; Karakaya, Burcu Kisa

2011-10-01

To define normal values of second trimester fetal nasal bone length (NBL) in a low-risk Turkish population. Prenatal records of singleton fetuses who underwent second trimester ultrasonographic examination in the 16 to 23 weeks of pregnancy were retrospectively analyzed for NBL and biometric measurements (BPD, FL and HL). The relationship among NBL and gestational age (GA), biparietal diameter (BPD), femur length (FL) and humerus length (HL) was determined. Additionally, percentile values of NBL for each gestational week were provided. A total of 1467 fetuses were included in this study. There was a significant linear association among NBL and GA (R(2) = 0.709), BPD (R(2) = 0.752), FL (R(2) = 0.742) and HL (R(2) = 0.747). Fifth percentile values of fetal NBL were 3.11 mm for 16th, 3.50 mm for 17th, 3.70 mm for 18th, 4.10 mm for 19th, 4.50 mm for 20th, 4.62 mm for 21st, 5.24 mm for 22nd and 5.37 mm for 23rd gestational weeks. The study provides normal ranges of NBL between 16 and 23 weeks of pregnancy in a low-risk Turkish population. Future studies with larger sample sizes including pregnancies carrying high risk for aneuploidy are needed to define cut-off values for NBL. Copyright © 2011 John Wiley & Sons, Ltd.

[Renal length measured by ultrasound in adult mexican population].

PubMed

Oyuela-Carrasco, J; Rodríguez-Castellanos, F; Kimura, E; Delgado-Hernández, R; Herrera-Félix, J P

2009-01-01

Renal length estimation by ultrasound is an important parameter in clinical evaluation of kidney disease and healthy donors. Changes in renal volume may be a sign of kidney disease. Correct interpretation of renal length requires the knowledge of normal limits, these have not been described for Latin American population. To describe normal renal length (RL) by ultrasonography in a group of Mexican adults. Ultrasound measure of RL in 153 healthy Mexican adults stratified by age. Describe the association of RL to several anthropometric variables. A total of 77 males and 76 females were scanner. The average age for the group was 44.12 +/- 15.44 years. The mean weight, body mass index (BMI) and height were 68.87 +/- 11.69 Kg, 26.77 +/- 3.82 kg/m2 and 160 +/- 8.62 cm respectively. Dividing the population by gender, showed a height of 166 +/- 6.15 cm for males and 154.7 +/- 5.97 cm for females (p =0.000). Left renal length (LRL) in the whole group was 105.8 +/- 7.56 mm and right renal length (RRL) was 104.3 +/- 6.45 mm (p = 0.000.) The LRL for males was 107.16 +/- 6.97 mm and for females was 104.6 +/- 7.96 mm. The average RRL for males was 105.74 +/- 5.74 mm and for females 102.99 +/- 6.85 mm (p = 0.008.) We noted that RL decreased with age and the rate of decline accelerates alter 60 years of age. Both lengths correlated significantly and positively with weight, BMI and height. The RL was significantly larger in males than in females in both kidneys (p = 0.036) in this Mexican population. Renal length declines after 60 years of age and specially after 70 years.

Retrospective cohort clinical investigation of a dental implant with a narrow diameter and short length for the partial rehabilitation of extremely atrophic jaws.

PubMed

Maló, Paulo S; de Araújo Nobre, Miguel A; Lopes, Armando V; Ferro, Ana S

2017-01-01

We investigated the short-term clinical outcomes of narrow-diameter short-length implants for the fixed-prosthetic partial rehabilitation of extremely resorbed jaws. Twenty-three patients requiring partial rehabilitations with narrow-platform short-length implants in any jaw were included in this study. In total, 30 implants 3.3 mm in diameter and 7 (n = 15 implants) or 8.5 (n = 15 implants) mm in length were inserted. The primary outcome measure was implant cumulative survival rate (CSR); the secondary outcome measures were marginal bone resorption at 1 and 3 years and the incidence of biologic and mechanical complications. Five patients (21.7%) with six implants (20%) were lost to follow-up. Two implants failed in two patients, yielding a CSR at 3 years of follow-up of 93.4%. The average (standard deviation) marginal bone resorption was 1.34 mm (0.95 mm) after the first year and 1.38 mm (0.78 mm) after the third year. Biologic complications occurred in three patients; mechanical complications occurred in three patients. Despite the limitations of the study, our findings show that the use of new narrow-diameter short-length implants for the rehabilitation of extremely atrophic regions is viable in the short-term, and can be considered a treatment alternative in extremely resorbed jaws.

Sex-ratio, seasonality and long-term variation in maturation and spawning of the brown shrimp Crangon crangon (L.) in the German Bight (North Sea)

NASA Astrophysics Data System (ADS)

Siegel, V.; Damm, U.; Neudecker, T.

2008-12-01

Aspects of the reproductive and maturation biology of the brown shrimp Crangon crangon (L.) were studied in various subareas of the German Bight (North Sea). The size-specific sex ratio of C. crangon was examined based on length frequency distribution data. The sex ratio for the smallest size groups at which sex was determined was typically around 0.5, indicating an even ratio between males and females. The proportion of females decreased in the 30-45 mm size range. In length classes larger than 50 mm, the proportion of females constantly increases to 100% at around 60 mm total length. We concluded that sex reversal from male to female may not occur in C. crangon. Size at sexual maturity was determined from the proportion of ovigerous females. Size at maturity ( L 50) was estimated as 55.4 and 62.0 mm total length for spring and winter data, respectively. The seasonal spawning cycle was studied over the period 1958-2005. Between mid February and late June and for size classes larger than 65 mm ovigerous shrimps exceeded 80% and reached up to 100% of the females in the population. This period can be seen as the core spawning season. From early August to early December the proportion of ovigerous shrimps in the female population is very low. Interannual differences in the seasonal process are obvious with a dramatic decline in C. crangon reproductive success in the late 1980s. Various options are discussed for the reasons of the decline and recovery of the reproductive performance.

Fluoroscopy and imageless navigation enable an equivalent reconstruction of leg length and global and femoral offset in THA.

PubMed

Weber, Markus; Woerner, Michael; Springorum, Robert; Sendtner, Ernst; Hapfelmeier, Alexander; Grifka, Joachim; Renkawitz, Tobias

2014-10-01

Restoration of biomechanics is a major goal in THA. Imageless navigation enables intraoperative control of leg length equalization and offset reconstruction. However, the effect of navigation compared with intraoperative fluoroscopy is unclear. We asked whether intraoperative use of imageless navigation (1) improves the relative accuracy of leg length and global and femoral offset restoration; (2) increases the absolute precision of leg length and global and femoral offset equalization; and (3) reduces outliers in a reconstruction zone of ± 5 mm for leg length and global and femoral offset restoration compared with intraoperative fluoroscopy during minimally invasive (MIS) THA with the patient in a lateral decubitus position. In this prospective study a consecutive series of 125 patients were randomized to either navigation-guided or fluoroscopy-controlled THA using sealed, opaque envelopes. All patients received the same cementless prosthetic components through an anterolateral MIS approach while they were in a lateral decubitus position. Leg length, global or total offset (representing the combination of femoral and acetabular offset), and femoral offset differences were restored using either navigation or fluoroscopy. Postoperatively, residual leg length and global and femoral offset discrepancies were analyzed on magnification-corrected radiographs of the pelvis by an independent and blinded examiner using digital planning software. Accuracy was defined as the relative postoperative difference between the surgically treated and the unaffected contralateral side for leg length and offset, respectively; precision was defined as the absolute postoperative deviation of leg length and global and femoral offset regardless of lengthening or shortening of leg length and offset throughout the THA. All analyses were performed per intention-to-treat. Analyzing the relative accuracy of leg length restoration we found a mean difference of 0.2 mm (95% CI, -1.0 to +1.4 mm; p = 0.729) between fluoroscopy and navigation, 0.2 mm (95 % CI, -0.9 to +1.3 mm; p = 0.740) for global offset and 1.7 mm (95 % CI, +0.4 to +2.9 mm; p = 0.008) for femoral offset. For the absolute precision of leg length and global and femoral offset equalization, there was a mean difference of 1.7 ± 0.3 mm (p < 0.001) between fluoroscopy and navigation. The biomechanical reconstruction with a residual leg length and global and femoral offset discrepancy less than 5 mm and less than 8 mm, respectively, succeeded in 93% and 98%, respectively, in the navigation group and in 54% and 95%, respectively, in the fluoroscopy group. Intraoperative fluoroscopy and imageless navigation seem equivalent in accuracy and precision to reconstruct leg length and global and femoral offset during MIS THA with the patient in the lateral decubitus position.

Novel measurements of the length of the subglottic airway in infants and young children.

PubMed

Sirisopana, Metee; Saint-Martin, Christine; Wang, Ning Nan; Manoukian, John; Nguyen, Lily H P; Brown, Karen A

2013-08-01

To date, the lengths of the subglottic and tracheal airway segments have been measured from autopsy specimens. Images of the head and neck obtained from computerized tomography (CT) provide an alternate method. Our objective in this study was to identify anatomic landmarks from CT scans in infants and young children to estimate the lengths of the subglottic and tracheal airway segments and to correlate these lengths with age. We performed a retrospective analysis of CT images of the neck for various diagnostic indications in children ≤3 years. We obtained planes of reconstruction at the level of the vocal cords (VCs), cricoid cartilage, and carina (C) which were parallel to each other and perpendicular to sagittal long axis of the trachea. The lengths of the subglottic airway (LengthSG) and total length of the laryngotracheal airway (LengthVC-C) were measured from the distance between, respectively, the VC versus cricoid cartilage and the VC versus C planes of reconstruction. Tracheal length was then calculated as the difference between LengthVC-C and LengthSG. Fifty-six children met the inclusion criteria. There were 29 boys. The median weight was 10.7 kg (range 3.1-19.0 kg). Regression analysis yielded mean LengthSG (mm) = 7.8 + 0.03·corrected age (months), r(2) = 0.07, P = 0.056; lower and upper 95% confidence interval for β = 0.03 were -0.001 and 0061. The mean LengthSG was 8.4 mm with an SD of 1.4 mm. The 95th percentile for LengthSG was 10.8 mm, and the 5% to 95% interquartile range was 4.9 mm. The estimate for the 95% confidence interval of the 95th percentile was between 10.2 and 11.3 mm. The LengthVC-C increased with age: mean LengthVC-C (cm) = 5.3 + 0.05·corrected age (months), r(2) = 0.7, P < 0.001. Tracheal length also increased with age: mean tracheal length (cm) = 4.5 + 0.05·corrected age (months), r(2) = 0.6, P < 0.001. We report a novel estimate method for the lengths of the airway segments between the VC and C in 56 infants and young children and suggest that the growth characteristics of the subglottic and tracheal airway may differ.

Recovery of macroinvertebrates by screening in the field: a comparison between coarse (1.18 mm) and fine (0.60 mm) mesh sieves

USGS Publications Warehouse

Dukerschein, J.T.; Gent, R.; Sauer, J.

1996-01-01

We evaluated the potential loss of target benthic macroinvertebrates from coarse-mesh field wash down of samples through a 1.18-mm mesh sieve nested on a 0.60-mm mesh sieve. Visible target organisms (midges, mayflies, and fingernail clams) in the 1.18-mm mesh sieve were removed from the sample and enumerated in the field. The entire contents of both sieves were preserved for subsequent laboratory enumeration under 4X magnification. Percent recoveries from each treatment were based on total intact organisms found in all sieves. Percent recovery for fingernail clams found in the field (31%) was lower than for mayflies (79%) and midges (88%). Laboratory enumeration of organisms retained by the 1.18-mm sieve yielded additional fingernail clams (to total 74% recovered in the field and lab), mayflies (to total 89%), and midges (to total 91%). If the 1.18-mm sieve is used alone in the field, it is adequate to monitor mayflies, midges >1 cm, and adult fingernail clams greater than or equal to 5.0 mm shell length.

Differences in stone size and ureteral dilation between obstructing proximal and distal ureteral calculi.

PubMed

Eisner, Brian H; Pedro, Renato; Namasivayam, Saravanan; Kambadakone, Avinash; Sahani, Dushyant V; Dretler, Stephen P; Monga, Manoj

2008-09-01

To examine the differences in ureteral dilation and calculus size between obstructing proximal and distal ureteral stones. A retrospective review of computed tomography (CT) scans from 176 consecutive patients with obstructing ureteral calculi was performed. For the calculi, the axial diameter was defined as the largest stone diameter on the axial CT images, and the coronal length was defined as the cephalocaudal length of the stone measured on the coronal CT images. Univariate and multivariate statistical analyses were performed. A total of 65 proximal and 111 distal ureteral calculi were analyzed. On univariate analysis, the proximal calculi were associated with a greater degree of ureteral dilation (mean 6.1 mm vs 5.3 mm, P = .01) and had a greater coronal length (mean 9.9 mm vs 8.3 mm, P = .005) than distal calculi. This association was also true on the multivariate analysis, which controlled for age and sex (P = .0004). No statistically significant difference was found in the axial calculus diameter for the proximal and distal stones (mean 5.3 mm vs 5.0 mm, P = .29). In a subset of 50 patients whose contralateral ureters (without stones) were measured for control comparison, the ureteral dilation in the ureters with stones was significantly greater than in the control ureters (proximal ureter 6.2 mm vs 4.3 mm, P = .001; distal ureter 4.7 mm vs 3.8 mm, P = .004). For proximal calculi, 72.3% were associated with ureteral dilation of less than 7 mm, 23.1% with 7-10 mm, and 4.6% with greater than 10 mm. For the distal calculi, 90.1% were associated with ureteral dilation of less than 7 mm, 6.3% with 7-10 mm, and 3.6% with greater than 10 mm. The coronal length was the largest measured diameter in 94% of the calculi, and the mean calculus coronal length was significantly greater than the mean axial diameter (8.9 mm vs 5.1 mm, respectively, P < .001). The results of our study have shown that proximal ureteral calculi are associated with a significantly greater degree of ureteral dilation and larger coronal length than are distal calculi. These findings should guide the endoscopist in planning intracorporeal ureteroscopic lithotripsy. We suggest obtaining CT coronal images to more accurately characterize obstructing ureteral stones.

Characterization of Upper Eyelid Tarsus and Lid Wiper Dimensions.

PubMed

Navascues-Cornago, Maria; Maldonado-Codina, Carole; Gupta, Ruchi; Morgan, Philip B

2016-09-01

To measure various dimensions of the upper tarsal plate and the area of upper lid wiper staining. The repeatability of the method of measurement was investigated. Thirty-five healthy non-contact lens wearers were enrolled. The following parameters were measured from digital images of the upper eyelid captured with a slitlamp camera: length, height, and total area of the tarsal plate and area of lid wiper staining (lissamine green). Measurements were performed in a randomized and masked fashion on two separate occasions by the same investigator using ImageJ (National Institutes of Health). Coefficients of repeatability (COR) were calculated. The dimensions (mean±SD) of the tarsal plate were 20.6±1.9 mm length, 7.9±0.8 mm height, and 103.3±18.8 mm total area. The area of lid wiper staining was 2.7±2.0 mm. No association was found between tarsal dimensions and lid wiper staining (all P>0.05). Image analysis COR values were 0.6 mm tarsal length, 0.1 mm tarsal height, 1.2 mm tarsal area, and 0.4 mm lid wiper staining. There was no significant difference between repeated measurements for any parameter (all P>0.05). Limits of agreement were narrow for all parameters, indicating good agreement between repeated measurements. This work has demonstrated that there is a wide range in the dimensions of the upper tarsal plate in an urban UK population. No association was found between the upper tarsal dimensions and lid wiper staining. ImageJ was shown to be a repeatable method to measure the dimensions of the upper tarsal plate and upper lid wiper staining.

Life histories of two deep-water Australian endemic elasmobranchs: Argus skate Dipturus polyommata and eastern spotted gummy shark Mustelus walkeri.

PubMed

Rigby, C L; White, W T; Smart, J J; Simpfendorfer, C A

2016-03-01

Two Australian endemic elasmobranchs, the Argus skate Dipturus polyommata and the eastern spotted gummy shark Mustelus walkeri, were collected from the by-catch of a prawn Melicertus plebejus trawl fishery off Queensland. Age and growth parameters were estimated from growth band counts in vertebral sections of 220 D. polyommata and 44 M. walkeri. Dipturus polyommata males and females had an observed maximum age of 10 years and reached maximum sizes of 369 and 371 mm total length (LT ), respectively. Mustelus walkeri lived longer, with the oldest female aged 16 years and measuring 1050 mm stretched total length (LST ), and oldest male aged 9 years and 805 mm LST . Dipturus polyommata grew relatively fast with a von Bertalanffy growth completion parameter of k = 0·208 year(-1) with males reaching maturity at 4·0 years (c. 278 mm LT ) and females at 5·1 years (c. 305 mm LT ). Mustelus walkeri grew more slowly with k = 0·033 year(-1) with males estimated to mature at 7-9 years (670-805 mm LST ) and females at 10-14 years (833-1012 mm LST ). Length at birth inferred from neonate D. polyommata was 89-111 mm LT while for M. walkeri it was estimated to be 273 LST based on the value of L0 from the von Bertalanffy growth model. Both species appeared to have continuous reproductive cycles and low fecundity with an average ovarian fecundity of eight follicles for D. polyommata and a litter size of five to seven pups for M. walkeri. Based on these life-history traits, D. polyommata is more resilient to fishing pressure than M. walkeri. © 2016 The Fisheries Society of the British Isles.

[Turbinella angulata and Busyconperversum (Mesogasteropoda: Turbinellidae and Melongenidae) population and reproductive dynamics in the Campeche Bank, Mexico].

PubMed

Valencia, Josefina Santos; Díaz, Martha Enríquez; Aranda, Dalila Aldana

2013-03-01

Turbinella angulata and Busycon perversum are two marine gastropods that support the 90% of conch fisheries in the Gulf of Mexico, nevertheless there is no information available to support a management strategy for both species. The aim of this work was to obtain preliminary fishery information to promote management actions for both species in the Campeche Bank. The population of conchs was sampled in 12 transects (150x1.5m) by SCUBA diving from April 2008 to March 2010. All conchs were collected and siphonal length (SL) was measured. These samples were complemented with data from the commercial catches, analyzing a total of 2 832 individuals of T angulata. Siphonal length varied between 63 and 282mm. Sex ratio was of 0.98:1 female:male. The von Bertalanffy growth equation parameters were: L infinity =346mm; K=0.30 and t(0)=-0.24. Spawning extended from January to May with a long resting stage from June to September for over 80% of the adult population. The first gonadic maturity (L50) was at 210mm (SL) for females and 200mm for males. For B. perversum a total of 1655 individuals were analyzed. Siphonal length varied between 78 and 291mm with significant differences between male and female (p<0.05). Sex ratio was of 1:0.25 female:male. The growth parameters obtained were: Linifinity=360mm; K=0.35 and t(0)=-0.19. The spawning period was from August to December with resting stage from January to April. The L50 was 215mm (LS) for females and 190mm for males. Both species presented one recruitment pulse. These results will be useful to design management schemes based on population dynamics and reproductive attributes.

ELECTRICAL AEROSOL DETECTOR (EAD) MEASUREMENTS AT THE ST. LOUIS SUPERSITE

EPA Science Inventory

The Model 3070A Electrical Aerosol Detector (EAD) measures a unique aerosol parameter called total aerosol length. Reported as mm/cm3, aerosol length can be thought of as a number concentration times average diameter, or simply as d1 weighting. This measurement falls between nu...

Calcaneotalar ratio: a new concept in the estimation of the length of the calcaneus.

PubMed

David, Vikram; Stephens, Terry J; Kindl, Radek; Ang, Andy; Tay, Wei-Han; Asaid, Rafik; McCullough, Keith

2015-01-01

Maintaining the calcaneal length after calcaneal fractures is vital to restoring the normal biomechanics of the foot, because it acts as an important lever arm to the plantarflexors of the foot. However, estimation of the length of the calcaneus to be reconstructed in comminuted calcaneal fractures can be difficult. We propose a new method to reliably estimate the calcaneal length radiographically by defining the calcaneotalar length ratio. A total of 100 ankle radiographs with no fracture in the calcaneus or talus taken in skeletally mature patients were reviewed by 6 observers. The anteroposterior lengths of the calcaneus and talus were measured, and the calcaneotalar length ratio was determined. The ratio was then used to estimate the length of the calcaneus. Interobserver reliability was determined using Cronbach's α coefficient and Pearson's correlation coefficient. The mean length of the calcaneus was 75 ± 0.6 mm, and the mean length of the talus was 59 ± 0.5 mm. The calcaneotalar ratio was 1.3. Using this ratio and multiplying it by the talar length, the mean average estimated length of the calcaneus was within 0.7 mm of the known calcaneal length. Cronbach's α coefficient and Pearson's correlation coefficient showed excellent interobserver reliability. The proposed calcaneotalar ratio is a new and reliable method to radiographically estimate the normal length of the calcaneus when reconstructing the calcaneus. Copyright © 2015 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Analysis of the biomechanical behavior of short implants: The photo-elasticity method.

PubMed

Pellizzer, Eduardo Piza; de Mello, Caroline Cantieri; Santiago Junior, Joel Ferreira; de Souza Batista, Victor Eduardo; de Faria Almeida, Daniel Augusto; Verri, Fellippo Ramos

2015-10-01

The aim of this study was to analyze the stress distribution of short implants supporting single unit or splinted crowns by the photo-elasticity method. Four photo-elastic models were produced: A (3.75×7 mm); B (3.75×7 mm, 3.75×7 mm and 3.75×7 mm); C (3.75×10 mm, 3.75×7 mm and 3.75×7 mm); D (3.75×13 mm, 3.75×7 mm and 3.75×7 mm). The prostheses were made with Ni-Cr alloy. A load of 100 N in the axial and oblique directions was applied, totaling 380 applications, individually capturing their images in each model. The data were randomized and analyzed qualitatively and quantitatively by 2 examiners. The oblique loading was significantly more damaging. The increase in length was favorable for stress distribution (p<0.05). The splinting was beneficial for the transmission of stresses mainly (p<0.05). The splinting of the crowns, as well as increasing the length of the first implant and axial loading was most beneficial in the stress distribution. Short splinted implants behaved better than single unit implants. Increasing of the length of the first implant significantly improved the stress distribution in all analyzed situations. Copyright © 2015 Elsevier B.V. All rights reserved.

Age, growth and reproduction of Sarcocheilichthys nigripinnis from the Qingyi Stream in the Huangshan Mountains.

PubMed

Yan, Yunzhi; Xu, Yinsheng; Chu, Ling; He, Shan; Chen, Yifeng

2012-06-01

Identifying the life-history strategies of fish and their associations with the surrounding environment is the basic foundation in the conservation and sustainable utilization of fish species. We examined the age, growth, and reproduction of Sarcocheilichthys nigripinnis using 352 specimens collected monthly from May 2009 to April 2010 in the Qingyi Stream. We found the sex ratio of this study population was 0.58:1 (female: male), significantly different from expected 1:1. Females and males both comprised four age groups. The annuli on the scales were formed during February and March. No obvious between-sex difference was observed in length-weight and length-scale-radius relationships. The total length in back-calculation significantly increased with age for both sexes, but did not differ significantly at each age between the two sexes. An inflection point was observed in the growth curves given by the von Bertalanffy growth function for total weight. At this inflection point, fish were 3.95 years. Both sexes reach their 50% sex maturity at age 2, when females and males were 94.7 mm and 103.0 mm total length. The temporal pattern of the gonado-somatic index corresponded to a spawning period that occurred from April through July. The non-synchronicity of egg diameter in each mature ovary during the breeding period suggested these fish may be batch spawners. The absolute fecundity increased significantly with total length and weight, whereas no significant correlation was observed between the relative fecundity and body size.

Does Core Length Taken per cc of Prostate Volume in Prostate Biopsy Affect the Diagnosis of Prostate Cancer?

PubMed

Deliktas, Hasan; Sahin, Hayrettin; Cetinkaya, Mehmet; Dere, Yelda; Erdogan, Omer; Baldemir, Ercan

2016-08-01

The aim of this study was to determine the minimal core length to be taken per cc of prostate volume for an effective prostate biopsy. A retrospective analysis was performed on the records of 379 patients who underwent a first prostate biopsy with 12 to 16 cores under transrectal ultrasound guidance between September 2012 and April 2015. For each patient, the core length per cc of the prostate and the percentage of sampled prostate volume were calculated, and these values were compared between the patients with and without prostate cancer. A total of 348 patients were included in the study. Cancer was determined in 26.4% of patients. The mean core length taken per cc of prostate and the percentage of sampled prostate volume were determined to be 3.40 ± 0.15 mm/cc (0.26%; range, 0.08-0.63 cc) in patients with cancer and 2.75 ± 0.08 mm/cc (0.20%; range, 0.04-0.66 cc) in patients without cancer (P = .000 and P = .000), respectively. Core length taken per cc of prostate of > 3.31 mm/cc was found to be related to an increase in the rates of prostate cancer diagnosis (odds ratio, 2.84; 95% confidence interval, 1.68-4.78). The rate of cancer determination for core length taken per cc of prostate of < 3.31 mm/cc was 19.9% and of > 3.31 mm/cc, 41.1%. Core length taken per cc of prostate and the percentage of sampled prostate volume are important morphometric parameters in the determination of prostate cancer. The results of study suggest a core length per cc of the prostate of > 3.31 mm/cc as a cutoff value for quality assurance. Copyright © 2016 Elsevier Inc. All rights reserved.

First report of the presence of Acartiabispinosa Carl, 1907 (Copepoda, Calanoida) in a semi-enclosed Bay (Sharm El-Maya), northern Red Sea with some notes on its seasonal variation in abundance and body size.

PubMed

El-Sherbiny, Mohsen M; Al-Aidaroos, Ali M

2014-01-01

The calanoid copepod, Acartiabispinosa Carl, 1907, is reported for the first time in the Red Sea, where it is found to be an important copepod in the mesozooplankton community structure of the Sharm El-Maya Bay. Female and male are fully redescribed and illustrated of as the mouthparts of this species have never previously been described and figured. Acartiabispinosa was collected in the plankton samples throughout the year and showed two peaks of abundance, a pronounced one in April (4234 individuals m(-3)), and second smaller peak during November (1784 individuals m(-3)). The average total length of females varied between 1.32 and 1.53 mm at the end of June and January respectively. For males, the average total length fluctuated between 1.07 and 1.16 mm at end of June and March respectively. Temperature showed an inverse relationship with the body length (P > 0.001) and seemed to be one of the prime factors affecting the body length of both sexes.

Change in First Metatarsal Length After Proximal and Distal Chevron Osteotomies for Hallux Valgus Deformity.

PubMed

Lee, Jun Young; Lee, Yeon Soo; Song, Kyoung Chul; Choi, Kwi Youn

2015-01-01

The present study assessed the changes in the length of the first metatarsal bone after performing proximal chevron metatarsal osteotomy (PCMO) or distal Chevron metatarsal osteotomy (DCMO) for patients with hallux valgus deformity. A total of 60 patients with moderate-to-severe hallux valgus deformity from July 2009 to July 2011 were randomly divided into the PCMO and DCMO groups, with 30 patients in each group. The distal soft tissue procedure was performed in the same method for both groups. Measurements were performed preoperatively, postoperatively, and at the last follow-up visit at 6.1 ± 0.8 months. The postoperative length change with respect to the preoperative length was 0.7 ± 2.5 mm and -0.7 ± 5.1 mm for the PCMO and DCMO groups, respectively, with a slight lengthening of the first metatarsal bone in the PCMO group and a shortening in the DCMO group (p < .01). The follow-up length change with respect to the preoperative length was -2.1 ± 3.0 mm and -4.4 ± 2.2 mm for the PCMO and DCMO groups, respectively, demonstrating a clear shortening of the first metatarsal length at the last follow-up point in the DCMO group (p < .01).When DCMO and the distal soft tissue procedure were performed, significant shortening was found at 6 months of follow-up. Copyright © 2015 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

The prevalence of short cervix between 20 and 24 weeks of gestation and vaginal progesterone for prolonging of gestation.

PubMed

Maerdan, Malipati; Shi, Chunyan; Zhang, Xiaoxiao; Fan, Lixin

2017-07-01

The objective of this study is to understand the prevalence of short cervical length between 20 and 24 weeks gestation in China and to evaluate the efficacy of micronized progesterone for prolonging gestation in nulliparous patients with a short cervix. From May 2010 to May 2015, a total of 25 328 asymptomatic women with singleton pregnancies at Peking University First Hospital had their cervical length routinely measured between 20 and 24 weeks of gestation. A cervical length of 25 mm or less was defined as a shortened cervical length. The therapies prescribed include vaginal micronized progesterone capsules (200 mg each night) or bed rest from 20 to 34 weeks of gestation. The primary outcome was spontaneous delivery before 33 weeks. (1) One hundred fourteen women had a cervical length of ≤25 mm (0.45%). (2) Twenty-nine of which with previous spontaneous preterm delivery or late pregnancy loss had cervical cerclage, the remaining 85 women by the use of vaginal progesterone or simply resting activity restriction to prevent preterm birth. (3) In 85 nulliparous women treated by progesterone or bed rest, progesterone use in cervical length between 10 and 20 mm was associated with a statistically significant reduction in the incidence of preterm birth at <33 weeks of gestation (9.5% versus 45.5%, p = 0.02) compared with bed rest. There were no significant differences in cervical length between 20 and 25 mm in their rates of spontaneous preterm delivery at <33 (5.3% versus 3.2%, p = 0.72), <37 (33.3% versus 54.5%, p = 0.25), or <35 weeks (14.3% versus 45.5, p = 0.06) of gestation between vaginal progesterone and bed rest. The rate of short cervical length was less than expected. Vaginal progesterone is efficacious for the prolonging of gestation in women with a cervical length of 10-20 mm in the mid-trimester for a singleton gestation and nulliparous women. For a cervical length of 20-25 mm in the mid trimester, vaginal progesterone compared with bed rest did not prolong pregnancy.

Prevalence and Length of the Anterior Loop of the Inferior Alveolar Nerve in Iranians.

PubMed

Moghddam, Maryam Rastegar; Davoudmanesh, Zeinab; Azizi, Nasim; Rakhshan, Vahid; Shariati, Mahsa

2017-10-01

The anterior loop of the inferior alveolar nerve is a sensitive anatomical feature that should be taken into account during installation of dental implants anterior to the mental foramen. This study was conducted to explore the controversy regarding prevalence and length. A total of 452 mandible quadrants of 234 patients (age: 50.1 ± 13.3 years, 113 males, 121 females) were studied using cone-beam computerized tomography. After reconstructing axial, frontal, and sagittal slices, the region between the most anterior point on the mental foramen and the most anterior part of the mandibular nerve was inspected for signs of anterior loop presence. If positive, the length of the anterior loop was measured in mm as the distance between the anterior border of mental foramen and the anterior border of the loop. Prevalence and length of the anterior loop were compared statistically between sexes and age groups. The anterior loop was observed in 106 quadrants (23.5% of 451 quadrants) of 95 patients (40.6% of 234 patients), of whom 11 had bilateral anterior loops. Prevalences were similar in males (41%) and females (39%, chi-square P =.791). The mean anterior loop length was 2.77 ± 1.56 mm (95% CI: 2.5-3.1 mm), without significant sex (regression beta = -0.159, P = .134) or age (beta = -0.059, P = .578) differences. The anterior loop might exist in about 40% of patients, regardless of their gender. The mean safe anterior distance from the anterior loop is about 3 mm + (2.5-3.1 mm) = 5.5-6.1 mm, regardless of age.

Key Parameters Evaluation for Hip Prosthesis with Finite Element Analysis

NASA Astrophysics Data System (ADS)

Guo, Hongqiang; Li, Dichen; Lian, Qin; Li, Xiang; Jin, Zhongmin

2007-09-01

Stem length and cross section are two key parameters that influence the stability and longevity of metallic hip prosthesis in the total hip arthroplasty (THA). In order to assess their influence to the stress and fatigue behavior of hip prosthesis, a series model of hip prosthesis with round-shaped or drum-shaped cross section, and with different stem lengths were created. These models were analyzed under both static and dynamic loading conditions with finite element analysis, and dynamic loading represents normal walking was used in the dynamic analysis. The stress on the metallic stem, cement, and adjacent bone were got, micromotion on the cement-metal interface were got too. Safety factors for fatigue life of the hip prothesis were calculated based on data obtained from dynamic analysis. Static analysis shows that drum-shaped cross section can decrease the displacement of the stem, that stress on drum-shaped stem focus on the corner of the femoral neck and the distal part of hip prosthesis, whereas the stress on the round-shaped stem distributes evenly over most part of the stem, and maximum stress on stem prosthesis fluctuates with stem length bottoming out at stem length range from 80 mm to 110 mm, that drum-shaped stems with drum height 8 mm generate more stress at the distal part of stem than drum-shaped stems with drum height 10 mm and round stems do. Dynamic and fatigue analysis shows that drum-shaped stem with drum height 10 mm and stem length 90 mm has the greatest safety factor therefore long fatigue life.

Root resorption of permanent incisors during three months of active orthodontic treatment.

PubMed

Batool, Iffat; Abbas, Hasnain; Abbas, Assad; Abbas, Iram

2010-01-01

Root resorption is one of the most common and undesirable sequelea of orthodontic treatment. The aim of this study was to evaluate the amount of root resorption in permanent incisors during 3 month active period of fixed orthodontic appliance therapy using periapical radiographs. Periapical radiographs of a total of 138 permanent teeth (n = 138, mandibular n1 = 52, maxillary n2 = 86) were evaluated for root resorption. All patients were treated with 3M MBT multi-bonded, pre-adjusted appliances with 0.022 inch slots. Initial levelling and alignment was achieved with 0.0175 inch co-axial wires. All four incisors (maxillary and mandibular) were measured for any change in root length. The change in root length between T0 (pre-treatment) and T1 (post-treatment) was measured in millimetres and expressed in terms of percentage of original root length. The mean pre treatment (T0) root length for the maxillary teeth (n1 = 62) was 19.27 +/- 2.86 mm and 20.01 +/- 2.57 mm for the mandibular teeth (n2 = 31). The post-treatment (T1) root length for the maxillary teeth was 18.96 +/- 2.85 mm and 19.49 +/- 2.4 mm for the mandibular teeth showing a mean resorption of 0.31 mm and 0.52 mm for the maxillary and mandibular teeth respectively. Root resorption was strongly correlated with active orthodontic appliance therapy with maxillary and mandibular incisors being most susceptible. It was found that root resorption can be detected even in the early levelling and alignment stages of orthodontic treatment.

Age and growth of round gobies in Lake Huron: Implications for food web dynamics

USGS Publications Warehouse

Duan, You J.; Madenjian, Charles P.; Xie, Cong X.; Diana, James S.; O'Brien, Timothy P.; Zhao, Ying M.; He, Ji X.; Farha, Steve A.; Huo, Bin

2016-01-01

Although the round goby (Neogobius melanostomus) has become established throughout the Laurentian Great Lakes, information is scarce on spatial variation in round goby growth between and within lakes. Based on a sample of 754 specimens captured in 2014, age, growth, and mortality of round gobies at four locations in Lake Huron were assessed via otolith analysis. Total length (TL) of round gobies ranged from 44 to 111 mm for Saginaw Bay, from 45 to 115 mm for Rockport, from 50 to 123 mm for Hammond Bay, and from 51 to 118 mm for Thunder Bay. Estimated ages of round gobies ranged from 2 to 5 years for Saginaw Bay, from 2 to 6 years for Rockport, and from 2 to 7 years for Hammond Bay and Thunder Bay. Sex-specific, body–otolith relationships were used to back-calculate total lengths at age, which were then fitted to von Bertalanffy growth models. For each sex, round goby growth showed significant spatial variation among the four locations within Lake Huron. At all four locations in Lake Huron, males grew significantly faster than females and attained a larger asymptotic length than females. Annual mortality rate estimates were high (62 to 85%), based on catch-curve analysis, suggesting that round gobies may be under predatory control in Lake Huron.

Comparing Transition-Edge Sensor Response Times in a Modified Contact Scheme with Different Support Beams

NASA Technical Reports Server (NTRS)

Beyer, A. D.; Kenyon, M. E.; Bumble, B.; Runyan, M. C.; Echternach, P. E.; Holmes, W. A.; Bock, J. J.; Bradford, C. M.

2013-01-01

We present measurements of the thermal conductance, G, and effective time constants, tau, of three transition-edge sensors (TESs) populated in arrays operated from 80-87mK with T(sub C) approximately 120mK. Our TES arrays include several variations of thermal architecture enabling determination of the architecture that demonstrates the minimum noise equivalent power (NEP), the lowest tau and the trade-offs among designs. The three TESs we report here have identical Mo/Cu bilayer thermistors and wiring structures, while the thermal architectures are: 1) a TES with straight support beams of 1mm length, 2) a TES with meander support beams of total length 2mm and with 2 phononfilter blocks per beam, and 3) a TES with meander support beams of total length 2mm and with 6 phonon-filter blocks per beam. Our wiring scheme aims to lower the thermistor normal state resistance R(sub N) and increase the sharpness of the transition alpha=dlogR/dlogT at the transition temperature T(sub C). We find an upper limit of given by (25+/-10), and G values of 200fW/K for 1), 15fW/K for 2), and 10fW/K for 3). The value of alpha can be improved by slightly increasing the length of our thermistors.

[Case-control study on methods of limb length control in hip arthroplasty].

PubMed

Zhang, Yang-yang; Zuo, Jian-lin; Gao, Zhong-li

2016-02-01

To introduce a new measuring tool for measuring postoperative limb length exactly, and to provide a convenient and effective method to control limb length after total hip replacement. From January 2013 to September 2014, 102 patients undergoing primary unilateral hip replacement were divided into two groups: experimental group and control group. There were 51 patients in the experimental group, including 25 males and 26 females, ranging in age from 37 to 92 years old, with an average of 60.41 years old. The patients in experimental group were treated with new method to control limb length. Other 51 patients in the control group, including 27 males and 24 females, ranging in age from 35 to 87 years old, with an average of 61.00 years old. The patients in the control group were treated with normal methods such as shuck test or limb touching. All the patients were operated by the same experienced surgeon. In the experimental group,total hip arthroplasties (THA) were performed on 35 patients with avascular necrosis of the femoral head or femoral neck fracture, and 16 patients were treated with hemiarthroplasty (HA). In the control group, 38 patients received THA and 13 patients received HA. On the anterior-posterior X-ray radiograph, several indexes were measured as follows: the distance of bilateral femoral offset (a), the height from tip of great trochanter to the rotation center of the femoral head (b) and the vertical distance between the top of the minor trochanter and the two tear drops line (c). The leg length discrepancy can be assessed with three parameters as follows: d1, the absolute value of the difference between the bilateral a values; d2, the difference between the bilateral b values; d3, the difference between the bilateral c values. The SPSS 21.0 was applied for the statistical analysis. In the experimental and control groups, d1 were 4.49 mm and 7.32 mm (P = 0.013); d2 were 2.37 mm and 4.32 mm (P = 0.033); d3 were 3.32 mm and 6.08 mm (P = 0.031). The values of d1, d2 and d3 in the experimental group were significant smaller than those in the control group. The new measuring tool and method can be used to control the limb length and offset effectively during operation.

Population dynamics of bowfin in a south Georgia reservoir: latitudinal comparisons of population structure, growth, and mortality

USGS Publications Warehouse

Porter, Nicholas J.; Bonvechio, Timothy F.; McCormick, Joshua L.; Quist, Michael

2014-01-01

The objectives of this study were to evaluate the population dynamics of bowfin (Amia calva) in Lake Lindsay Grace, Georgia, and to compare those dynamics to other bowfin populations. Relative abundance of bowfin sampled in 2010 in Lake Lindsay Grace was low and variable (mean±SD; 2.7±4.7 fish per hour of electrofishing). Total length (TL) of bowfin collected in Lake Lindsay Grace varied from 233–683 mm. Age of bowfin in Lake Lindsay Grace varied from 0–5 yr. Total annual mortality (A) was estimated at 68%. Both sexes appeared to be fully mature by age 2 with gonadosomatic index values above 8 for females and close to 1 for males. The majority of females were older, longer, and heavier than males. Bowfin in Lake Lindsay Grace had fast growth up to age 4 and higher total annual mortality than the other populations examined in this study. A chi-square test indicated that size structure of bowfin from Lake Lindsay Grace was different than those of a Louisiana population and two bowfin populations from the upper Mississippi River. To further assess bowfin size structure, we proposed standard length (i.e., TL) categories: stock (200 mm, 8 inches), quality (350 mm, 14 inches), preferred (460 mm, 18 inches), memorable (560 mm, 22, inches), and trophy (710 mm, 28 inches). Because our knowledge of bowfin ecology is limited, additional understanding of bowfin population dynamics provides important insight that can be used in management of bowfin across their distribution.

Progress in long scale length laser plasma interactions

NASA Astrophysics Data System (ADS)

Glenzer, S. H.; Arnold, P.; Bardsley, G.; Berger, R. L.; Bonanno, G.; Borger, T.; Bower, D. E.; Bowers, M.; Bryant, R.; Buckman, S.; Burkhart, S. C.; Campbell, K.; Chrisp, M. P.; Cohen, B. I.; Constantin, C.; Cooper, F.; Cox, J.; Dewald, E.; Divol, L.; Dixit, S.; Duncan, J.; Eder, D.; Edwards, J.; Erbert, G.; Felker, B.; Fornes, J.; Frieders, G.; Froula, D. H.; Gardner, S. D.; Gates, C.; Gonzalez, M.; Grace, S.; Gregori, G.; Greenwood, A.; Griffith, R.; Hall, T.; Hammel, B. A.; Haynam, C.; Heestand, G.; Henesian, M.; Hermes, G.; Hinkel, D.; Holder, J.; Holdner, F.; Holtmeier, G.; Hsing, W.; Huber, S.; James, T.; Johnson, S.; Jones, O. S.; Kalantar, D.; Kamperschroer, J. H.; Kauffman, R.; Kelleher, T.; Knight, J.; Kirkwood, R. K.; Kruer, W. L.; Labiak, W.; Landen, O. L.; Langdon, A. B.; Langer, S.; Latray, D.; Lee, A.; Lee, F. D.; Lund, D.; MacGowan, B.; Marshall, S.; McBride, J.; McCarville, T.; McGrew, L.; Mackinnon, A. J.; Mahavandi, S.; Manes, K.; Marshall, C.; Menapace, J.; Mertens, E.; Meezan, N.; Miller, G.; Montelongo, S.; Moody, J. D.; Moses, E.; Munro, D.; Murray, J.; Neumann, J.; Newton, M.; Ng, E.; Niemann, C.; Nikitin, A.; Opsahl, P.; Padilla, E.; Parham, T.; Parrish, G.; Petty, C.; Polk, M.; Powell, C.; Reinbachs, I.; Rekow, V.; Rinnert, R.; Riordan, B.; Rhodes, M.; Roberts, V.; Robey, H.; Ross, G.; Sailors, S.; Saunders, R.; Schmitt, M.; Schneider, M. B.; Shiromizu, S.; Spaeth, M.; Stephens, A.; Still, B.; Suter, L. J.; Tietbohl, G.; Tobin, M.; Tuck, J.; Van Wonterghem, B. M.; Vidal, R.; Voloshin, D.; Wallace, R.; Wegner, P.; Whitman, P.; Williams, E. A.; Williams, K.; Winward, K.; Work, K.; Young, B.; Young, P. E.; Zapata, P.; Bahr, R. E.; Seka, W.; Fernandez, J.; Montgomery, D.; Rose, H.

2004-12-01

The first experiments on the National Ignition Facility (NIF) have employed the first four beams to measure propagation and laser backscattering losses in large ignition-size plasmas. Gas-filled targets between 2 and 7 mm length have been heated from one side by overlapping the focal spots of the four beams from one quad operated at 351 nm (3ω) with a total intensity of 2 × 1015 W cm-2. The targets were filled with 1 atm of CO2 producing up to 7 mm long homogeneously heated plasmas with densities of ne = 6 × 1020 cm-3 and temperatures of Te = 2 keV. The high energy in an NIF quad of beams of 16 kJ, illuminating the target from one direction, creates unique conditions for the study of laser-plasma interactions at scale lengths not previously accessible. The propagation through the large-scale plasma was measured with a gated x-ray imager that was filtered for 3.5 keV x-rays. These data indicate that the beams interact with the full length of this ignition-scale plasma during the last ~1 ns of the experiment. During that time, the full aperture measurements of the stimulated Brillouin scattering and stimulated Raman scattering show scattering into the four focusing lenses of 3% for the smallest length (~2 mm), increasing to 10-12% for ~7 mm. These results demonstrate the NIF experimental capabilities and further provide a benchmark for three-dimensional modelling of the laser-plasma interactions at ignition-size scale lengths.

What do sales data tell us about implant survival?

PubMed

Seemann, Rudolf; Jirku, Alexander; Wagner, Florian; Wutzl, Arno

2017-01-01

The aim of this study was to evaluate the influence of implant diameter, length and shape on a surrogate parameter of implant survival; i.e. the implant return rate in a big data analysis. A retrospective study was conducted and the factors influencing the success rates of 69,377 sold implants over a seven-year period were evaluated. The osseointegration program of a reseller provides reliable data of a single country. Implant loss rates were investigated using logistic regression models and regressed by implant type, diameter, and length. The return rate of 69,377 sold implants was 2.78% and comparable to implant loss rates in previous published prospective studies as its surrogate parameter. A total of 80% of implant returns had occurred within 157 days, and an additional 15% within 750.25 days. Diameters of 3.8 to 5.0mm showed the lowest return rates with its bottom in the 4.3mm implant whilst 6.0mm implants had significantly higher return rates. In comparison to the most sold implant length (13mm) shorter implants showed significantly higher early return rates. The study provides evidence that in cases of standard indications and sufficient bone, the use of screw typed dental implants with 3.8 or 4.3 diameter and 11 or 13 mm length shows the lowest implant return rates. Other implants may be selected only in specific indications.

Comparison of impact strength of acrylic resin reinforced with kevlar and polyethylene fibres.

PubMed

Kamath, G; Bhargava, K

2002-01-01

The present study was done to evaluate the impact strengths of heat-activated acrylic resins reinforced with Kevlar fibres, polyethylene fibres and unreinforced heat activated acrylic resin. Each of three groups had 25 specimens. Brass rods of uniform length of 40 mm and diameter of 8 mm were used to prepare the moulds. A combination of long fibres (40 mm length) and short fibres (6 mm length) were used. The total amount of fibres incorporated was limited to 2% by weight of the resin matrix. Short and long fibres of equal weight were incorporated. The short fibres were mixed with polymer and monomer and packed into the mould, while, the long axis of the specimen, perpendicular to the applied force. The specimens were then processed. Impact strength testing was done on Hounsfield's impact testing machine. Kevlar fibre reinforced heat activated acrylic resin specimens recorded higher mean impact strength of 0.8464 Joules, while polyethylene fibres reinforced heat activated acrylic resin recorded mean impact strength of 0.7596 joules. The unreinforced heat activated acrylic resin recorded mean impact strength of 0.3440 Joules.

Behaviour of wrapped cold-formed steel columns under different loading conditions

NASA Astrophysics Data System (ADS)

Baabu, B. Hari; Sreenath, S.

2017-07-01

The use of Cold Formed Steel (CFS) sections as structural members is widely accepted because of its light nature. However, the load carrying capacity of these sections will be less compared to hot rolled sections. This study is meant to analyze the possibility of strengthening cold formed members by wrapping it with Glass Fiber Reinforced Polymer (GFRP) laminates. Light gauge steel columns of cross sectional dimensions 100mm x 50mm x 3.15mm were taken for this study. The effective length of the section is about 750mm. A total of 8 specimens including the control specimen is tested under axial and eccentric loading. The columns were tested keeping both ends hinged. For both loading cases the buckling behaviour, ultimate load carrying capacity and load-deflection characteristics of the CFS columns were analyzed. The GFRP laminates were wrapped on columns in three different ways such that wrapping the outer surface of web and flange throughout the length of specimen, wrapping the outer surface of web alone throughout the length of specimen and wrapping the outer surface of web and flange for the upper half length of the specimen where the buckling is expected. For both loading cases, the results indicated that the column with wrapping at the outer surface of web and flange throughout the length of specimen provides better strength for it.

Total Human Eye Allotransplantation: Developing Surgical Protocols for Donor and Recipient Procedures

PubMed Central

Davidson, Edward H.; Wang, Eric W.; Yu, Jenny Y.; Fernandez-Miranda, Juan C.; Wang, Dawn J.; Richards, Nikisha; Miller, Maxine; Schuman, Joel S.; Washington, Kia M.

2017-01-01

Background Vascularized composite allotransplantation of the eye is an appealing, novel method for reconstruction of the nonfunctioning eye. The authors’ group has established the first orthotopic model for eye transplantation in the rat. With advancements in immunomodulation strategies together with new therapies in neuroregeneration, parallel development of human surgical protocols is vital for ensuring momentum toward eye transplantation in actual patients. Methods Cadaveric donor tissue harvest (n = 8) was performed with orbital exenteration, combined open craniotomy, and endonasal approach to ligate the ophthalmic artery with a cuff of paraclival internal carotid artery, for transection of the optic nerve at the optic chiasm and transection of cranial nerves III to VI and the superior ophthalmic vein at the cavernous sinus. Candidate recipient vessels (superficial temporal/internal maxillary/facial artery and superficial temporal/facial vein) were exposed. Vein grafts were required for all anastomoses. Donor tissue was secured in recipient orbits followed by sequential venous and arterial anastomoses and nerve coaptation. Pedicle lengths and calibers were measured. All steps were timed, photographed, video recorded, and critically analyzed after each operative session. Results The technical feasibility of cadaveric donor procurement and transplantation to cadaveric recipient was established. Mean measurements included optic nerve length (39 mm) and caliber (5 mm), donor artery length (33 mm) and caliber (3 mm), and superior ophthalmic vein length (15 mm) and caliber (0.5 mm). Recipient superficial temporal, internal maxillary artery, and facial artery calibers were 0.8, 2, and 2 mm, respectively; and superior temporal and facial vein calibers were 0.8 and 2.5 mm, respectively. Conclusion This surgical protocol serves as a benchmark for optimization of technique, large-animal model development, and ultimately potentiating the possibility of vision restoration transplantation surgery. PMID:27879599

Evaluation of Two New Electronic Apex-Locator-Controlled Handpieces Using a NiTi Rotary File: An In Vitro Study.

PubMed

Nazarimoghadam, Kiumarz; Labaf, Hossein

2013-11-01

The aim of this in-vitro study was to compare the accuracy of two new electronic apex-locator controlled handpieces (EALHs) using the first rotary Mtwo file while rotating in the canal. A total of 36 extracted mandibular molar teeth were selected. The lengths of the mesio-buccal canals to the major foramina were measured directly using a size 10 K-file introduced in the canal until the tip was visible under a loupe and then 0.5 mm was subtracted from the recorded lengths as the actual working lengths (AWLs). Subsequently, the teeth were randomly assigned to two groups and embedded in an alginate model. Auto-stop function of the EALHs was preset at "0.5" mark and then electrical working lengths (EWLs) in groups 1 and 2 were recorded by VDW GOLD and Dentaport ZX, respectively. Analysis of variance (ANOVA, 1-way) and Tukey pairwise multiple comparison intervals (0.05) were used to compare the accuracy of the two electronic devices. For VDW GOLD, 61.1% of the measurements were within ±0.5 mm and 88.9% were within ±1 mm of the AWL. For Dentaport ZX, 88.9% of the measurements were within ±0.5 mm and 94.4% were within ±1mm of the AWL. There was no significant difference between AWLs and EWLs (p=0.466 for Dentaport ZX and p=0.283 for VDW Gold) and between the accuracy of the two devices in determining the EWL (p=0.8). Both Dentaport ZX and VDW Gold were suitable for determining working length using a rotary file. To avoid over instrumenting the canal, we recommend setting the devices to automatically stop or reverse the rotary file at 1 mm level.

Length-weight relationship and condition factor of white shrimp Penaeus merguiensis captured in ecosystem mangrove of Bagan Asahan, Tanjungbalai, Asahan, North Sumatra, Indonesia

NASA Astrophysics Data System (ADS)

Suryanti, A.; Riza, N.; Raza'i, T. S.

2018-02-01

White Shrimp Penaeus merguiensis was commonly found in Mangrove Ecosystem of Bagan Asahan Village. The purpose of this research are to determine length-weight relationship and condition factor of white shrimp Penaeus merguiensis around ecosystem mangrove waters in Bagan Asahan Village. This research was conducted for 3 month in Maret until Mei 2017 with determination of research station used purposive sampling method. The shrimp samples were taken by shrimp trawl. The result showed that 98 shrimp which consists of 58 males and 40 female. The carapace length of female shrimp between 6,05 - 22,125 mm and total weight ranged from 0,12 - 6,95 g. Male shrimp had carapace length between 7.125 - 18.25 mm and total weigth ranged from 0.14 - 3.82 g. Female and male white shrimp had different growth pattern. Female shrimp had b = 2.984 included in negaive allometric and male shrimps with b = 3.187 included in positive allometric. The value of correlation coefficients was more than 90% for both male and female showed very strong relation between length carapace and body weight. The value of shrimp condition factor ranged from 0.570 - 1.773 and included to flat (thin) body shrimp.

Use of piezosurgery during maxillary sinus elevation: clinical results of 40 consecutive cases.

PubMed

Cassetta, Michele; Ricci, Laura; Iezzi, Giovanna; Calasso, Sabrina; Piattelli, Adriano; Perrotti, Vittoria

2012-12-01

The aim of this study was to evaluate the performance of piezoelectric devices during sinus elevation to determine the percentage of sinus membrane perforation and the time required to perform the antrostomy and elevation of the membrane. A total of 35 patients and 40 grafted sinuses were included. The parameters recorded were bony window length and height, bone thickness, osteotomy area, operative time, and number of perforations. Seven (17.5%) membrane perforations were observed, which were repaired with resorbable membranes. The mean length, height, and thickness of the osteotomy were 13.8 ± 2.9 mm, 6.9 ± 1.4 mm, and 1.4 ± 0.4 mm, respectively. The mean osteotomy area was 96.8 ± 32.2 mm(2), and the mean operative time was 10.3 ± 2.1 minutes. This study demonstrated that a piezoelectric device could be an attractive alternative for successful sinus augmentation.

2-year follow-up report on micromotion of a short tibia stem. A prospective, randomized RSA study of 59 patients.

PubMed

Molt, Mats; Toksvig-Larsen, Sören

2015-01-01

A shortened tibial stem could influence the early prosthetic fixation. We therefore compared the short stem to the standard-length stem using radiostereometric analysis (RSA) as primary outcome measure. 60 patients were randomized to receive a cemented Triathlon total knee arthroplasty (TKA) with a tibial tray of either standard or short stem length. The patients were blinded regarding treatment allocation. The micromotion of the tibial component was measured by RSA postoperatively, at 3 months, and after 1 and 2 years; clinical outcome was measured with the American Knee Society score (AKSS) and the knee osteoarthritis and injury outcome score (KOOS). The maximum total point motion (MTPM) for the standard stem was 0.36 (SD 0.16) mm at 3 months, 0.51 (SD 0.27) mm at 1 year, and 0.54 (SD 0.28) mm at 2 years. For the short stem, it was 0.42 (0.24) mm, 0.59 (0.43) mm, and 0.61 (0.39) mm. 4 short-stemmed components and 2 standard-stemmed components had more than 0.2 mm of migration between the first- and second-year follow-up, and were classified as continuously migrating. The short-stemmed cemented tibial prosthesis showed an early prosthetic migratory pattern similar to that of the standard-stemmed cemented Triathlon knee prosthesis. The number of continuously migrating tibial plates in each group is predictive of a lower revision rate than 5% at 10 years.

First report of the presence of Acartia bispinosa Carl, 1907 (Copepoda, Calanoida) in a semi-enclosed Bay (Sharm El-Maya), northern Red Sea with some notes on its seasonal variation in abundance and body size

PubMed Central

El-Sherbiny, Mohsen M.; Al-Aidaroos, Ali M.

2014-01-01

Abstract The calanoid copepod, Acartia bispinosa Carl, 1907, is reported for the first time in the Red Sea, where it is found to be an important copepod in the mesozooplankton community structure of the Sharm El-Maya Bay. Female and male are fully redescribed and illustrated of as the mouthparts of this species have never previously been described and figured. Acartia bispinosa was collected in the plankton samples throughout the year and showed two peaks of abundance, a pronounced one in April (4234 individuals m-3), and second smaller peak during November (1784 individuals m-3). The average total length of females varied between 1.32 and 1.53 mm at the end of June and January respectively. For males, the average total length fluctuated between 1.07 and 1.16 mm at end of June and March respectively. Temperature showed an inverse relationship with the body length (P > 0.001) and seemed to be one of the prime factors affecting the body length of both sexes. PMID:25349502

Does joint line elevation after revision knee arthroplasty affect tibio-femoral kinematics, contact pressure or collateral ligament lengths? An in vitro analysis

PubMed Central

Kowalczewski, Jacek B.; Chevalier, Yan; Okon, Tomasz; Innocenti, Bernardo; Bellemans, Johan

2015-01-01

Introduction Correct restoration of the joint line is generally considered as crucial when performing total knee arthroplasty (TKA). During revision knee arthroplasty however, elevation of the joint line occurs frequently. The general belief is that this negatively affects the clinical outcome, but the reasons are still not well understood. Material and methods In this cadaveric in vitro study the biomechanical consequences of joint line elevation were investigated using a previously validated cadaver model simulating active deep knee squats and passive flexion-extension cycles. Knee specimens were sequentially tested after total knee arthroplasty with joint line restoration and after 4 mm joint line elevation. Results The tibia rotated internally with increasing knee flexion during both passive and squatting motion (range: 17° and 7° respectively). Joint line elevation of 4 mm did not make a statistically significant difference. During passive motion, the tibia tended to become slightly more adducted with increasing knee flexion (range: 2°), while it went into slighlty less adduction during squatting (range: –2°). Neither of both trends was influenced by joint line elevation. Also anteroposterior translation of the femoral condyle centres was not affected by joint line elevation, although there was a tendency for a small posterior shift (of about 3 mm) during squatting after joint line elevation. In terms of kinetics, ligaments lengths and length changes, tibiofemoral contact pressures and quadriceps forces all showed the same patterns before and joint line elevation. No statistically significant changes could be detected. Conclusions Our study suggests that joint line elevation by 4 mm in revision total knee arthroplasty does not cause significant kinematic and kinetic differences during passive flexion/extension movement and squatting in the tibio-femoral joint, nor does it affect the elongation patterns of collateral ligaments. Therefore, clinical problems after joint line elevation are probably situated in the patello-femoral joint or caused by joint line elevation of more than 4 mm. PMID:25995746

Planar solar concentrator featuring alignment-free total-internal-reflection collectors and an innovative compound tracker.

PubMed

Teng, Tun-Chien; Lai, Wei-Che

2014-12-15

This study proposed a planar solar concentrator featuring alignment-free total-internal-reflection (TIR) collectors and an innovative compound tracker. The compound tracker, combining a mechanical single-axis tracker and scrollable prism sheets, can achieve a performance on a par with dual-axis tracking while reducing the cost of the tracking system and increasing its robustness. The alignment-free TIR collectors are assembled on the waveguide without requiring alignment, so the planar concentrator is relatively easily manufactured and markedly increases the feasibility for use in large concentrators. Further, the identical TIR collector is applicable to various-sized waveguide slab without requiring modification, which facilitates flexibility regarding the size of the waveguide slab. In the simulation model, the thickness of the slab was 2 mm, and its maximal length reached 6 m. With an average angular tolerance of ±0.6°, and after considering both the Fresnel loss and the angular spread of the sun, the simulation indicates that the waveguide concentrator of a 1000-mm length provides the optical efficiencies of 62-77% at the irradiance concentrations of 387-688, and the one of a 2000-mm length provides the optical efficiencies of 52-64.5% at the irradiance concentrations of 645-1148. Alternatively, if a 100-mm horizontally staggered waveguide slab is collocated with the alignment-free TIR collectors, the optical efficiency would be greatly improved up to 91.5% at an irradiance concentration of 1098 (C(geo) = 1200X).

Radio-anatomical Study of the Greater Palatine Canal and the Pterygopalatine Fossa in a Lebanese Population: A Consideration for Maxillary Nerve Block

PubMed Central

Aoun, Georges; Nasseh, Ibrahim; Sokhn, Sayde

2016-01-01

Aim: The aim of this study was to describe the morphology of the component, greater palatine canal-pterygopalatine fossa (GPC-PPF), in a Lebanese population using cone-beam computed tomography (CBCT) technology. Materials and Methods: CBCT images of 79 Lebanese adult patients (38 females and 41 males) were included in this study, and a total of 158 cases were evaluated bilaterally. The length and path of the GPCs-PPFs were determined, and the data obtained analyzed statistically. Results: In the sagittal plane, of all the GPCs-PPFs assessed, the average length was 35.02 mm on the right and 35.01 mm on the left. The most common anatomic path consisted in the presence of a curvature resulting in an internal narrowing whose average diameter was 2.4 mm on the right and 2.45 mm on the left. The mean diameter of the upper opening was 5.85 mm on the right and 5.82 mm on the left. As for the lower opening corresponding to the greater palatine foramen, the right and left average diameters were 6.39 mm and 6.42 mm, respectively. Conclusion: Within the limits of this study, we concluded that throughout the Lebanese population, the GPC-PPF path is variable with a predominance of curved one (77.21% [122/158] in both the right and left sides); however, the GPC-PPF length does not significantly vary according to gender and side. PMID:27833777

A four kHz repetition rate compact TEA CO2 laser

NASA Astrophysics Data System (ADS)

Zheng, Yijun; Tan, Rongqing

2013-09-01

A compact transversely excited atmospheric (TEA) CO2 laser with high repetition-rate was reported. The size of the laser is 380 mm×300 mm×200 mm, and the discharge volume is 12×103 mm3. The laser cavity has a length of 320mm and consists of a totally reflective concave mirror with a radius of curvature of 4 m (Cu metal substrate coated with Au) and a partially reflecting mirror. The ultraviolet preionization makes the discharge even and stable，the output energy can be as high as 28 mJ under the circumstance of free oscillation, and the width of the light pulse is 60ns．To acquire the high wind velocity, a turbocharger is used in the system of the fast-gas flow cycle. When the wind speed is 100m/s, the repetition rate of the transversely excited atmospheric CO2 laser is up to 2 kHz. On this basis, a dual modular structure with two sets of the gas discharge unit is adopted to obtain a higher pulse repetition frequency output. The dual discharge unit composed two sets of electrodes and two sets of turbo fan. Alternate trigger technology is used to make the two sets of discharge module work in turn with repetition frequency of 2 kHz, the discharge interval of two sets of the gas discharge unit can be adjusted continuously from 20 microseconds to 250 microseconds. Under the conditions of maintaining the other parameters constant, the repetition frequency of the laser pulse is up to 4 kHz. The total size of laser with dual modular structure is 380mm×520mm×200mm, and the discharge volume is 24×103 mm3 with the cavity length of 520mm.

Effects of Mechanical Ventilation on Heart Geometry and Mitral Valve Leaflet Coaptation During Percutaneous Edge-to-Edge Mitral Valve Repair.

PubMed

Patzelt, Johannes; Zhang, Yingying; Seizer, Peter; Magunia, Harry; Henning, Andreas; Riemlova, Veronika; Patzelt, Tara A E; Hansen, Marc; Haap, Michael; Riessen, Reimer; Lausberg, Henning; Walker, Tobias; Reutershan, Joerg; Schlensak, Christian; Grasshoff, Christian; Simon, Dan I; Rosenberger, Peter; Schreieck, Juergen; Gawaz, Meinrad; Langer, Harald F

2016-01-25

This study sought to evaluate a ventilation maneuver to facilitate percutaneous edge-to-edge mitral valve repair (PMVR) and its effects on heart geometry. In patients with challenging anatomy, the application of PMVR is limited, potentially resulting in insufficient reduction of mitral regurgitation (MR) or clip detachment. Under general anesthesia, however, ventilation maneuvers can be used to facilitate PMVR. A total of 50 consecutive patients undergoing PMVR were included. During mechanical ventilation, different levels of positive end-expiratory pressure (PEEP) were applied, and parameters of heart geometry were assessed using transesophageal echocardiography. We found that increased PEEP results in elevated central venous pressure. Specifically, central venous pressure increased from 14.0 ± 6.5 mm Hg (PEEP 3 mm Hg) to 19.3 ± 5.9 mm Hg (PEEP 20 mm Hg; p < 0.001). As a consequence, the reduced pre-load resulted in reduction of the left ventricular end-systolic diameter from 43.8 ± 10.7 mm (PEEP 3 mm Hg) to 39.9 ± 11.0 mm (PEEP 20 mm Hg; p < 0.001), mitral valve annulus anterior-posterior diameter from 32.4 ± 4.3 mm (PEEP 3 mm Hg) to 30.5 ± 4.4 mm (PEEP 20 mm Hg; p < 0.001), and the medio-lateral diameter from 35.4 ± 4.2 mm to 34.1 ± 3.9 mm (p = 0.002). In parallel, we observed a significant increase in leaflet coaptation length from 3.0 ± 0.8 mm (PEEP 3 mm Hg) to 5.4 ± 1.1 mm (PEEP 20 mm Hg; p < 0.001). The increase in coaptation length was more pronounced in MR with functional or mixed genesis. Importantly, a coaptation length >4.9 mm at PEEP of 10 mm Hg resulted in a significant reduction of PMVR procedure time (152 ± 49 min to 116 ± 26 min; p = 0.05). In this study, we describe a novel ventilation maneuver improving mitral valve coaptation length during the PMVR procedure, which facilitates clip positioning. Our observations could help to improve PMVR therapy and could make nonsurgical candidates accessible to PMVR therapy, particularly in challenging cases with functional MR. Copyright © 2016 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

Radiological examinations of the anatomy of the inferior turbinate using digital volume tomography (DVT).

PubMed

Balbach, L; Trinkel, V; Guldner, C; Bien, S; Teymoortash, A; Werner, J A; Bremke, M

2011-06-01

Since the last 120 years there were only few descriptions of the anatomical sizes of the inferior turbinate in the literature. On this background the current study should evaluate the radiological dimensions of the inferior turbinate and the septum using DVT. The latest generation of the Accu-I-tomo was used. The data of 100 adult patients have been evaluated. The bony length was found to be 38.9 mm, the mucosal length 51.0 mm. The findings of the total mucosal thickness at different measuring points were between 8.1 mm and 10.9 mm, those of the bony thickness were between 0.9 mm and 2.3 mm and those of the bony height were between 3.9 mm and 20.8 mm. The results of this radiological study are able to point out the importance of preoperative anatomical evaluation of radiological images. The preoperative focus on the individual anatomy is very important because of the choice of an adequate surgical treatment. Today new radiological techniques can help to find out whether the reason for hypertrophied turbinates is caused by bone, mucosa or both. This knowledge enables a concerted treatment concept.

Gulf Sturgeon Facts

USGS Publications Warehouse

Sulak, Kenneth J.; Randall, Michael T.

2008-01-01

Sturgeon: An ancient type of fish, with 5 rows of armor scutes, a cartilaginous skeleton, long snout, suction mouth, no teeth, and 4 barbels. Photograph of a Gulf sturgeon. The total length of a 5-month old is 313 mm.

LASER PLASMA AND LASER APPLICATIONS: Plasma transparency in laser absorption waves in metal capillaries

NASA Astrophysics Data System (ADS)

Anisimov, V. N.; Kozolupenko, A. P.; Sebrant, A. Yu

1988-12-01

An experimental investigation was made of the plasma transparency to heating radiation in capillaries when absorption waves propagated in these capillaries as a result of interaction with a CO2 laser pulse of 5-μs duration. When the length of the capillary was in excess of 20 mm, total absorption of the radiation by the plasma was observed at air pressures of 1-100 kPa. When the capillary length was 12 mm, a partial recovery of the transparency took place. A comparison was made with the dynamics and recovery of the plasma transparency when breakdown of air took place near the free surface.

How do dairy cows chew?--particle size analysis of selected feeds with different particle length distributions and of respective ingested bolus particles.

PubMed

Schadt, I; Ferguson, J D; Azzaro, G; Petriglieri, R; Caccamo, M; Van Soest, P; Licitra, G

2012-08-01

Not only feed but also respective bolus particle size could alter diet efficiency and cow performance. The objective of this project was to characterize particle size of selected feeds and respective swallowed boli. Feed samples included 6 different particle length rye grass hay samples, 1 grass silage, 1 corn silage, and 1 total mixed ration (TMR). Rye grass hay samples consisted of long hay and chopped hay particles retained on the 19- (19_PSPS hay), 8- (8_PSPS hay), and 1.18-mm (1.18_PSPS hay) Penn State Particle Separator (PSPS) screens and those collected on the pan (PSPS_pan hay). A sixth hay treatment was rye grass forage cut at 50-mm lengths and dried to hay (50-mm hay). Treatments were offered to 4 nonlactating and 4 lactating cows following rumen evacuation. Swallowed boli were collected and the number of chews per gram of ingested feed dry matter was determined. Feed and bolus particles of lengths ≥5mm were collected on a 1.6-mm screen using a horizontal wet sieving technique. This cut point was chosen, as the literature suggests that most fecal particles are shorter than 5mm. Dry matter proportions on this screen (PROP_1.6) were determined and particle lengths of retained particles were measured by image analysis. Mean particle lengths (ML) were calculated considering particles ≥5mm in length. Boli of long hay, of 19_PSPS hay, of 8_PSPS hay, and of 50-mm hay had similar ML of 10 to 11mm. Bolus PROP_1.6 were also similar between these treatments, ranging from 0.54 to 0.69. Bolus particle lengths and distributions of these treatments were not related to respective hay particles. Bolus of 1.18_PSPS hay had PROP_1.6 of 0.51 and a smaller ML of 8mm. The PSPS_pan hay had PROP_1.6 of only 0.33, but was still chewed intensely. Apparently, little particle size reduction occurred when cows ate the TMR or the silages. Feed and respective bolus PROP_1.6 were as follows: 0.66 and 0.59 in grass silage, 0.52 and 0.55 in corn silage, and 0.44 and 0.38 in the TMR. Feed and respective bolus ML were as follows: 13.8 and 11.6mm in grass silage, 12.0 and 11.2mm in corn silage, and 13.1 and 12.5mm in the TMR. Rye grass hay particles retained on PSPS screens ≥8mm, with ML of at least 25mm were longer compared with TMR particles, but respective bolus particles were shorter. Bolus particle size is not associated with the size of large feed particles chewed to a constant size that is appropriate for deglutition. This size may be related to feed chemical composition. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Ophthalmic diagnostic tests, orbital anatomy, and adnexal histology of the broad-snouted caiman (Caiman latirostris).

PubMed

Oriá, Arianne P; Oliveira, Alberto Vinícius D; Pinna, Melissa H; Martins Filho, Emanoel F; Estrela-Lima, Alessandra; Peixoto, Tiago C; Silva, Renata Maria M da; Santana, Fernanda O; Meneses, Íris Daniela S; Requião, Kátia G; Ofri, Ron

2015-01-01

The aim of this study was to establish normal ophthalmic parameters for selected diagnostic tests, and to describe the orbital anatomy and adnexal histology of the broad-snouted caiman. A total of 35 Caiman latirostris that were free of obvious ocular diseases were used to measure the parameters in this investigation. Ages ranged from 5 to 15 years. Ophthalmic diagnostic tests were conducted, including evaluation of tear production with Schirmer Tear test-1 (STT1), culture of the conjunctival bacterial flora, applanation tonometry, conjunctival cytology, nictiating membrane incursion frequency test (NMIFT), endodontic absorbent paper point tear test (EAPPTT), palpebral fissure length measurement (PFL) and B-mode ultrasonography. Adnexal histology and skull samples were studied. Mean (±SD) STT1 was 3.4 ± 3.6 mm/min (95% confidence interval of 2.01-4.78 mm/min), intraocular pressure (IOP) was 12.9 ± 6.2 mmHg, NMIFT was 6.0 ± 3.5, EAPPTT was 17.1 ± 2.5 mm/min, PFL was 28.9 ± 3.0 mm, anterior chamber depth was 3.1 ± 0.3 mm, lens axial length was 8.4 ± 0.6 mm, vitreous chamber depth was 7.9 ± 0.7 mm and axial globe length was 19.9 ± 1.3 mm. For all animals evaluated, Bacillus sp., Diphteroids and Staphylococcus sp. were predominant. © 2013 American College of Veterinary Ophthalmologists.

Are 10-, 10-12-, or > 12-mm prostate biopsy core quality control cutoffs reasonable?

PubMed

Sanches, Brunno C F; Lalli, Ana Luiza; Azal Neto, Wilmar; Billis, Athanase; Reis, Leonardo Oliveira

2018-07-01

To explore the role of prostate biopsy core length on prediction of index tumor clinical significance and localization on radical prostatectomy (RP) and time to recurrence, hypothesizing 10-, 10-12-, or > 12-mm minimum core as potential biopsy quality control. Assessed 2424 prostate biopsy cores and corresponding RP of 202 patients submitted to the first set of 12 cores prostate biopsy between 2010 and 2015. Analyzed biopsy core length, age, prostate volume (PV), free and total PSA ratio, PSA density, RP index tumor clinical significance, extension, localization, surgical margins, and cancer control. Prostate biopsy confronted to surgical specimens defined Gleason grade-grouping system (1-5) agreement. Median age was 63.7 years, PSA 10.1 ng/dl, PSA density 28%, and mean follow-up 5 years. Recurrence was identified in 64 (31.7%) patients and predicted by PSA > 10 at time of diagnosis (p = 0.008), seminal vesicle invasion (p = 0.0019), core tumor percentage (p = 0.033), and tumor localization predominantly in the prostate base (p = 0017). The mean core length was longer in index tumor positive cores (p = 0.043) and in tumors classified as clinically insignificant (p = 0.011), without impact on tumor localization (basal vs apical p = 0.592; left vs. right p = 0.320). Biopsy core length categories (≤ 10, 10-12 and > 12 mm) did not significantly impact Gleason grade-grouping agreement or time to recurrence (p > 0.05). Core length was not significantly different in all Gleason grade-groupings 1-5 (p = 0.312). Prostate biopsy core length impacts tumor characterization; however, 10 mm minimum core length and even 10-12- and > 12-mm categories failed as a biopsy quality control in our data.

The Middle Temporal Artery: Surgical Anatomy and Exposure for Cerebral Revascularization.

PubMed

Rubio, Roberto Rodriguez; Lawton, Michael T; Kola, Olivia; Tabani, Halima; Yousef, Sonia; Meybodi, Ali Tayebi; Burkhardt, Jan-Karl; El-Sayed, Ivan; Benet, Arnau

2018-02-01

The middle temporal artery (MTA) is the proximal medial branch of the superficial temporal artery (STA), supplying the temporalis muscle along with deep temporal arteries. Its use in vascularized flaps for reconstructive and otologic procedures has been described, yet its potential use in neurosurgery has not been studied. We report a novel technique for exposing the MTA and evaluated its characteristics for extracranial-intracranial cerebrovascular bypass. After a curvilinear frontotemporal incision in 10 cadaveric specimens, the STA was dissected from distal to proximal. The horizontal portion of MTA was found posterolateral to the posterior end of the zygomatic root and was followed proximally until its origin and distally until its 2 terminal branches. The total length, visible branches, and caliber of MTA were measured. The mean total harvested length of MTA was 31.7 ± 5.1 mm, with an average proximal caliber of 1.7 ± 0.4 mm, and distal caliber of 1.3 ± 0.5 mm. There were 4-6 terminal MTA branches. The caliber of the proximal STA trunk was 2.5 ± 0.5 mm. The origin of the MTA was visible with a mean distance of 16.9 ± 4.8 mm inferior to the PEZR. The parotid gland was traversed and a communicating auriculotemporal nerve to the temporal branch of the facial nerve crossed MTA in 2 specimens. MTA can be safely harvested with an anterolateral approach, following its horizontal portion at the level of the zygomatic root, which is constant. The length and caliber of MTA makes it a potential alternative donor vessel or interposition graft for extracranial-intracranial bypass, especially when other donors are unavailable. Copyright © 2017 Elsevier Inc. All rights reserved.

Proposed standard-weight (W(s)) equations for kokanee, golden trout and bull trout

USGS Publications Warehouse

Hyatt, M.H.; Hubert, W.A.

2000-01-01

We developed standard-weight (W(s)) equations for kokanee (lacustrine Oncorhynchus nerka), golden trout (O. aguabonita), and bull trout (Salvelinus confluentus) using the regression-line-percentile technique. The W(s) equation for kokanee of 120-550 mm TL is log10 W(s) = -5.062 + 3.033 log10 TL, when W(s) is in grams and TL is total length in millimeters; the English-unit equivalent is log10 W(s) = -3.458 + 3.033 log10 TL, when W(s) is in pounds and TL is total length in inches. The W(s) equation for golden trout of 120-530 mm TL is log10 W(s) = -5.088 + 3.041 log10 TL, with the English-unit equivalent being log10 W(s) = -3.473 + 3.041 log10 TL. The W(s) equation for bull trout of 120-850 mm TL is log10 W(s) = -5.327 + 3.115 log10 TL, with the English-unit equivalent being log10 W(s) = -3.608 + 3.115 log10 TL.

What do sales data tell us about implant survival?

PubMed Central

Seemann, Rudolf; Jirku, Alexander; Wagner, Florian; Wutzl, Arno

2017-01-01

Objective The aim of this study was to evaluate the influence of implant diameter, length and shape on a surrogate parameter of implant survival; i.e. the implant return rate in a big data analysis. Materials and methods A retrospective study was conducted and the factors influencing the success rates of 69,377 sold implants over a seven-year period were evaluated. The osseointegration program of a reseller provides reliable data of a single country. Implant loss rates were investigated using logistic regression models and regressed by implant type, diameter, and length. Results The return rate of 69,377 sold implants was 2.78% and comparable to implant loss rates in previous published prospective studies as its surrogate parameter. A total of 80% of implant returns had occurred within 157 days, and an additional 15% within 750.25 days. Diameters of 3.8 to 5.0mm showed the lowest return rates with its bottom in the 4.3mm implant whilst 6.0mm implants had significantly higher return rates. In comparison to the most sold implant length (13mm) shorter implants showed significantly higher early return rates. Conclusions The study provides evidence that in cases of standard indications and sufficient bone, the use of screw typed dental implants with 3.8 or 4.3 diameter and 11 or 13 mm length shows the lowest implant return rates. Other implants may be selected only in specific indications. PMID:28222128

Correlation between Visible Length of the Iris and the Length of the Maxillary Central Incisor Using Digital Image Analysis- A Pilot Study.

PubMed

Rohini; Hemalatha; Chander, Gopi Naveen; Anitha, Kuttae Viswanathan

2017-02-01

Complete denture therapy is one such modality where science and art goes hand in hand. Selection of artificial teeth for completely edentulous patients is not easy in the absence of pre extraction records, because till date concrete guidelines do not exist. The purpose of this study was to determine if a correlation existed between the visible length of the iris and the length of the maxillary central incisor to potentially provide a guide for teeth selection. A total of 20 Indian dental students consented to participate in the pilot study. Standardized digital images of the face revealing the eyes and component of teeth on smiling was captured using a digital camera. The digital measurements of the visible iris length (medial aperture height, tangential to iris) and the length of the maxillary central incisor from the zenith to the incisal edge were analysed using Adobe Photoshop creative cloud software. The data was statistically evaluated and results were tabulated. Karl Pearson's Coefficient of Correlation was utilized to detect if any association existed between the two variables. The mean value of length of central incisor was 10.39 mm and the mean value of the visible length of iris was found to be 12.9 mm. A Pearson correlation analysis revealed an r-value <0.3 indicating minimal association between the two variables with a p-value >0.01 (.322). On inference, the correlation between the visible iris length and that of maxillary central incisor were unable to produce a strong positive statistical association. However, an association factor between the two has been obtained. Deduction of 2.5 mm from the dimension of visible iris length will help in attaining the length of artificial maxillary central incisor tooth.

Changes in shape and astigmatism of total, anterior, and posterior cornea after long versus short clear corneal incision cataract surgery.

PubMed

Hayashi, Ken; Yoshida, Motoaki; Hirata, Akira; Yoshimura, Koichi

2018-01-01

To compare changes in the shape and astigmatism of the total, anterior, and posterior cornea between eyes with long-length clear corneal incisions (CCIs) and eyes with short-length CCIs in cataract surgery. Hayashi Eye Hospital, Fukuoka, Japan. Prospective case series. Both eyes of patients having phacoemulsification with temporal CCIs were randomized to have a long-length (≥1.75 mm) or short-length (<1.75 mm) CCI. Corneal astigmatic changes were decomposed to vertical/horizontal (Jackson cross-cylinder, axes at 180 degrees and 90 degrees [J0]) and oblique changes (Jackson cross-cylinder, axes at 45 degrees and 135 degrees [J45]) using power vector analysis. Corneal shape changes were assessed using the average of the difference map on videokeratography 2 days and 2, 4, and 8 weeks postoperatively. The mean J0 and J45 values of the total cornea in the 120 eyes evaluated were significantly greater in the long CCI group than in the short CCI group at all follow-ups (P ≤ .0290). The videokeratography showed a wedge-shaped flattening in the total and anterior cornea and a steepening in the posterior cornea around the CCI 2 days postoperatively in both groups. This wound-related flattening of the total and anterior cornea rapidly reduced but persisted until 8 weeks, whereas the steepening of the posterior cornea disappeared within 4 weeks. These changes extended closer to the central cornea in the long CCI group than in the short CCI group. Corneal astigmatic changes were significantly greater after long CCI than after short CCI. The wound-related shape changes occurred immediately postoperatively but rapidly diminished. Copyright © 2018 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Reproductive and population parameters of spiny dogfish Squalus acanthias in the south-western Atlantic Ocean.

PubMed

Colonello, J H; Cortés, F; Belleggia, M; Massa, A M

2016-05-01

The objective of this study was to estimate reproductive and population parameters of the spiny dogfish Squalus acanthias for the south-western Atlantic Ocean. In total, 2714 specimens (1616 males and 1098 females) were collected from surveys carried out using research vessels. Males ranged from 225 to 861 mm total length (LT ) and females from 235 to 925 mm LT . The size at maturity of females (651 mm) was significantly greater than that of males (565 mm). The maximum proportion of mature individuals (Pmax ) of the gestation ogive was <1, which indicates that a proportion of mature females was not in gestation. This inactivity may be explained by the occurrence of resting periods between cycles or by the asynchrony of the reproductive cycle. The estimated Pmax for the maternity ogive suggested that about one third of mature females were in the maternity stage (i.e. with embryos >156 mm). The temporal and spatial co-occurrence of non-gravid adult females at different stages of ovarian development, as well as gravid females at all embryonic development stages would indicate that the female reproductive cycle in the south-western Atlantic Ocean is asynchronous. The results indicate that S. acanthias is susceptible to fishing pressure on account of its length at maturity, extended reproductive cycles and low fecundity. © 2016 The Fisheries Society of the British Isles.

Reproductive traits of shovelnose sturgeon Scaphirhynchus platorynchus (Rafinesque, 1820) in the lower Platte River, Nebraska

USGS Publications Warehouse

Hamel, M. J.; Rugg, M.L.; Pegg, M.A.; Patino, Reynaldo; Hammen, J.J.

2015-01-01

We assessed reproductive status, fecundity, egg size, and spawning dynamics of shovelnose sturgeon Scaphirhynchus platorynchus in the lower Platte River. Shovelnose sturgeon were captured throughout each year during 2011 and 2012 using a multi-gear approach designed to collect a variety of fish of varying sizes and ages. Fish were collected monthly for a laboratory assessment of reproductive condition. Female shovelnose sturgeon reached fork length at 50% maturity (FL50) at 547 mm and at a minimum length of 449 mm. The average female spawning cycle was 3–5 years. Mean egg count for adult females was 16 098 ± 1103 (SE), and mean egg size was 2.401 ± 0.051 (SE) mm. Total fecundity was positively correlated with length (r2 = 0.728; P < 0.001), mass (r2 = 0.896; P < 0.001), and age (r2 = 0.396; P = 0.029). However, fish size and age did not correlate to egg size (P > 0.05). Male shovelnose sturgeon reached FL50 at 579 mm and at a minimum length of 453 mm. The average male spawning cycle was 1–2 years. Reproductively viable male and female sturgeon occurred during the spring (March–May) and autumn (September–October) in both years, indicating spring and potential autumn spawning events. Shovelnose sturgeon in the lower Platte River are maturing at a shorter length and younger age compared to populations elsewhere. Although it is unknown if the change is plastic or evolutionary, unfavorable environmental conditions or over-harvest may lead to hastened declines compared to other systems.

Food of young-of-the-year lake trout (Salvelinus namaycush) in Presque Isle Harbor, Lake Superior

USGS Publications Warehouse

Swedberg, Donald V.; Peck, James W.

1984-01-01

The food habits of young lake trout (Salvelinus namaycush) were studied by examining the digestive tracts of 293 young-of-the-year collected in Presque Isle Harbor, Lake Superior. Lake trout in the 25 to 27-mm length range started to eat food organisms before all of their yolk material was absorbed. Organisms consumed by the 25 to 27-mm young-of-the-year included Chironomidae, Copepoda (Harpacticoida, Calanoida, Cyclopoida), and Cladocerea (Daphnia spp., Bosmina sp., Chydorus sp.). Chironomid pupae and chironomid larvae accounted for 74% and 5%, respectively, of the total volume of food eaten by the young lake trout in Presque Isle Harbor. Although copepods, cladocerans, and mysids were present in many stomachs, their contribution to the total volume of food was only 15%. Some lake trout in the 32 to 54-mm length range had consumed fry of sculpin (Cottus spp.) or rainbow smelt (Osmerus mordax), but the overall contribution of fish fry to the total volume of food was only 4% (frequency of occurrence, 10%). The lake trout in Presque Isle Harbor fed heavily on planktonic organisms, sparingly on benthic organisms, and were opportunistic feeders that appeared to prey on whatever forage organisms were available in the shallow nearshore waters.

Reproductive biology of the crocodile shark Pseudocarcharias kamoharai.

PubMed

Oliveira, P; Hazin, F H V; Carvalho, F; Rego, M; Coelho, R; Piercy, A; Burgess, G

2010-05-01

From February 2005 to September 2007, a total of 490 crocodile sharks Pseudocarcharias kamoharai, caught as by-catch in the swordfish and tuna longline fishery that operates in the tropical western Atlantic Ocean, was studied in regard to their reproductive biology. Maximum observed total lengths (L(T)) were 1220 and 1090 mm for females and males respectively, with a high proportion of the catch being composed of mature specimens. Sexual maturity was attained at 760-810 mm L(T) for males (L(T50) = 800 mm) and 870-980 mm L(T) for females (L(T50) = 916 mm). The size at birth was estimated at 415 mm L(T). Temporal variation in gonad morphology and mass suggests that in this region P. kamoharai, an aplacental viviparous species with oophagy, does not show a well-defined reproductive seasonality, with mating and parturition occurring possibly over an extended period of the year. Mean +/-S.D. fecundity was estimated to be 3.9 (+/- 0.6) pups per reproductive cycle.

A complete VLBI delay model for deforming radio telescopes: the Effelsberg case

NASA Astrophysics Data System (ADS)

Artz, T.; Springer, A.; Nothnagel, A.

2014-12-01

Deformations of radio telescopes used in geodetic and astrometric very long baseline interferometry (VLBI) observations belong to the class of systematic error sources which require correction in data analysis. In this paper we present a model for all path length variations in the geometrical optics of radio telescopes which are due to gravitational deformation. The Effelsberg 100 m radio telescope of the Max Planck Institute for Radio Astronomy, Bonn, Germany, has been surveyed by various terrestrial methods. Thus, all necessary information that is needed to model the path length variations is available. Additionally, a ray tracing program has been developed which uses as input the parameters of the measured deformations to produce an independent check of the theoretical model. In this program as well as in the theoretical model, the illumination function plays an important role because it serves as the weighting function for the individual path lengths depending on the distance from the optical axis. For the Effelsberg telescope, the biggest contribution to the total path length variations is the bending of the main beam located along the elevation axis which partly carries the weight of the paraboloid at its vertex. The difference in total path length is almost 100 mm when comparing observations at 90 and at 0 elevation angle. The impact of the path length corrections is validated in a global VLBI analysis. The application of the correction model leads to a change in the vertical position of mm. This is more than the maximum path length, but the effect can be explained by the shape of the correction function.

Scalp and skull influence on near infrared photon propagation in the Colin27 brain template.

PubMed

Strangman, Gary E; Zhang, Quan; Li, Zhi

2014-01-15

Near-infrared neuromonitoring (NIN) is based on near-infrared spectroscopy (NIRS) measurements performed through the intact scalp and skull. Despite the important effects of overlying tissue layers on the measurement of brain hemodynamics, the influence of scalp and skull on NIN sensitivity are not well characterized. Using 3555 Monte Carlo simulations, we estimated the sensitivity of individual continuous-wave NIRS measurements to brain activity over the entire adult human head by introducing a small absorption perturbation to brain gray matter and quantifying the influence of scalp and skull thickness on this sensitivity. After segmenting the Colin27 template into five tissue types (scalp, skull, cerebrospinal fluid, gray matter and white matter), the average scalp thickness was 6.9 ± 3.6 mm (range: 3.6-11.2mm), while the average skull thickness was 6.0 ± 1.9 mm (range: 2.5-10.5mm). Mean NIN sensitivity - defined as the partial path length through gray matter divided by the total photon path length - ranged from 0.06 (i.e., 6% of total path length) at a 20mm source-detector separation, to over 0.19 at 50mm separations. NIN sensitivity varied substantially around the head, with occipital pole exhibiting the highest NIRS sensitivity to gray matter, whereas inferior frontal regions had the lowest sensitivity. Increased scalp and skull thickness were strongly associated with decreased sensitivity to brain tissue. Scalp thickness always exhibited a slightly larger effect on sensitivity than skull thickness, but the effect of both varied with SD separation. We quantitatively characterize sensitivity around the head as well as the effects of scalp and skull, which can be used to interpret NIN brain activation studies as well as guide the design, development and optimization of NIRS devices and sensors. Copyright © 2013 Elsevier Inc. All rights reserved.

Influence of pellet diameter and length on the quality of pellets and performance, nutrient utilisation and digestive tract development of broilers fed on wheat-based diets.

PubMed

Abdollahi, M R; Ravindran, V; Wester, T J; Ravindran, G; Thomas, D V

2013-06-01

1. The influence of pellet diameter and length on the quality of pellets and performance, nutrient utilisation and digestive tract development of broilers given wheat-based diets was examined from 10 to 42 d of age. The experimental design was a 2 × 2 factorial arrangement of treatments evaluating two pellet diameters (3 and 4.76 mm) and two pellet lengths (3 and 6 mm). From 0 to 9 d of age, all birds were offered a common starter diet pelleted with a 3-mm diameter die and 3-mm length. Broiler grower (d 10 to 21) and finisher (d 22 to 42) diets, based on wheat, were formulated and then subjected to the 4 different treatments. 2. In grower diets, increasing pellet diameter and pellet length reduced the gelatinised starch (GS) content of the diets. In finisher diets, GS content of 3-mm diameter pellets did not change with increasing pellet length but decreased in 4.76-mm diameter pellets. 3. In grower and finisher diets, increments in intact pellet weight, pellet durability index and pellet hardness with increasing pellet length were greater in 3-mm diameter pellets than those with 4.76-mm diameter. 4. Increasing pellet length from 3 to 6 mm increased apparent metabolisable energy values. Neither the interaction nor main effects were significant for the ileal digestibility of nitrogen and starch. 5. During the grower period (d 10 to 21), birds given pellets of 6-mm length had greater body-weight gain than those given 3-mm length pellets. Feeding 6-mm length pellets decreased feed per body-weight gain compared to 3-mm length pellets. During the finisher (d 22 to 42) and whole grow-out (d 10 to 42) periods, while different pellet lengths had no effect on feed per body-weight gain values at 3-mm pellet diameter, increasing the pellet length decreased feed per body-weight gain at 4.76-mm pellet diameter. 6. Increasing pellet diameter and pellet length reduced the relative length of duodenum. Birds given 3-mm diameter pellets had heavier proventriculus compared to those given 4.76-mm diameter pellets. 7. Overall, the data suggest that increasing the pellet length from 3 to 6 mm improved the body-weight gain and feed per body-weight gain during the grower period (d 10 to 21). While the positive effect on body-weight gain disappeared as the birds grew older, improvements in feed per body-weight gain were maintained over the finisher and whole grow-out periods only in 4.76-mm diameter pellets. Small diameter die holes and longer pellet lengths may be considered as potential manipulations to manufacture high-quality pellets under low conditioning temperatures.

Longitudinal patterns in flathead catfish relative abundance and length at age within a large river: Effects of an urban gradient

USGS Publications Warehouse

Paukert, C.P.; Makinster, A.S.

2009-01-01

We investigated the spatial variation of flathead catfish (Pylodictis olivaris) relative abundance and growth in the 274 km long Kansas River to determine if population dynamics of catfish are related to urbanization. Electrofishing was conducted at 462 random sites throughout the river in summer, 2005-2006 to collect fish. Relative abundance of age 1 fish (???200mm), subadult (>200-400mm) and adult fish (>400 mm) ranged from 0.34 to 14.67 fish h-1, mean length at age 1 was 165 (range: 128-195) mm total length (TL) and mean length at age 3 was 376 mm TL (range: 293-419mm TL). The proportion of land use within 200 m of the river edge was between 0 and 0.54 urban. River reaches with high relative abundance of age 1 flathead catfish had high relative abundance of subadult and adult catfish. River reaches with fast flathead catfish growth to age 1 had fast growth to age 3. High urban land use and riprap in the riparian area were evident in river reaches near the heavily populated Kansas City and Topeka, Kansas, USA. Reaches with increased number of log jams and islands had decreased riparian agriculture. Areas of low urbanization had faster flathead catfish growth (r = 0.67, p = 0.005). Relative abundance of flathead catfish was higher in more agricultural areas (r = -0.57, p = 0.02). Changes in land use in riverine environments may alter population dynamics of a fish species within a river. Spatial differences in population dynamics need to be considered when evaluating riverine fish populations. Published in 2008 by John Wiley & Sons Ltd.

Correcting length-frequency distributions for imperfect detection

USGS Publications Warehouse

Breton, André R.; Hawkins, John A.; Winkelman, Dana L.

2013-01-01

Sampling gear selects for specific sizes of fish, which may bias length-frequency distributions that are commonly used to assess population size structure, recruitment patterns, growth, and survival. To properly correct for sampling biases caused by gear and other sources, length-frequency distributions need to be corrected for imperfect detection. We describe a method for adjusting length-frequency distributions when capture and recapture probabilities are a function of fish length, temporal variation, and capture history. The method is applied to a study involving the removal of Smallmouth Bass Micropterus dolomieu by boat electrofishing from a 38.6-km reach on the Yampa River, Colorado. Smallmouth Bass longer than 100 mm were marked and released alive from 2005 to 2010 on one or more electrofishing passes and removed on all other passes from the population. Using the Huggins mark–recapture model, we detected a significant effect of fish total length, previous capture history (behavior), year, pass, year×behavior, and year×pass on capture and recapture probabilities. We demonstrate how to partition the Huggins estimate of abundance into length frequencies to correct for these effects. Uncorrected length frequencies of fish removed from Little Yampa Canyon were negatively biased in every year by as much as 88% relative to mark–recapture estimates for the smallest length-class in our analysis (100–110 mm). Bias declined but remained high even for adult length-classes (≥200 mm). The pattern of bias across length-classes was variable across years. The percentage of unadjusted counts that were below the lower 95% confidence interval from our adjusted length-frequency estimates were 95, 89, 84, 78, 81, and 92% from 2005 to 2010, respectively. Length-frequency distributions are widely used in fisheries science and management. Our simple method for correcting length-frequency estimates for imperfect detection could be widely applied when mark–recapture data are available.

Intraradicular Appearances Affect Radiographic Interpretation of the Periapical Area.

PubMed

Biscontine, Ana C; Diliberto, Adam J; Hatton, John F; Woodmansey, Karl F

2017-12-01

No research exists evaluating the influences of specific variables such as obturation length, radiodensity, or the presence of voids on interpretation of periradicular area. The purpose of this study was to evaluate the effects of obturation length, radiodensity, and the presence of voids on the radiographic interpretations of periapical areas. In a Web-based survey, 3 test image groups of variable obturation lengths, radiodensities, and numbers of voids were presented to observers for evaluation of the periapical areas. Intracanal areas of the images were altered by using Adobe Photoshop to create 3 test image groups. Each observer reviewed 2 control images and 1 image from each test image group. Responses were recorded in a 5-point Likert-type scale. Within each test image group, the periapical areas were identical. Kruskal-Wallis, Mann-Whitney U, and Cliff's delta statistical tests were used to analyze results. A total of 748 observer responses were analyzed. Significant differences (P ≤ .01) in the median Likert-type scale responses were identified between the following paired groups: 3 mm short and 1 mm short, 3 mm short and flush, lower radiodensity and higher radiodensity, lower radiodensity and intermediate radiodensity, no voids and several voids, and several voids and single void. Effect sizes ranged from 0.19 to 0.41. Significant differences were noted within all 3 test image groups: length, radiodensity, and presence of voids. Length of obturation had the largest effect on interpretation of the periapical area, with the 3 mm short radiographic obturation length image interpreted less favorably. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Ophthalmic diagnostic tests in captive red-footed tortoises (Chelonoidis carbonaria) in Salvador, northeast Brazil.

PubMed

Oriá, Arianne P; Silva, Renata M Monção; Pinna, Melissa H; Oliveira, Alberto Vinícius D; Ferreira, Paulo Roberto B; Martins Filho, Emanoel F; Meneses, Iris Daniela S; Requião, Kátia G; Ofri, Ron

2015-01-01

The aim of this study was to establish normal ophthalmic parameters for select diagnostic tests in red-footed tortoises (Chelonoides carbonaria). A total of 52 animals, approximately 20-30 years old, were studied. Ophthalmic diagnostic tests included culturing of the normal conjunctival bacterial flora in summer and winter, evaluation of tear production using Schirmer tear test (STT) and endodontic absorbent paper point tear test in two different environmental temperatures (EAPPTT-1 at 32 °C and EAPPTT-2 at 18 °C), cytology of conjunctival cells, B-mode ultrasonography, measurement of palpebral fissure length (PFL), and applanation tonometry (in two different positions). In both seasons, Gram-positive bacteria were predominant. Median (± IQR/2) STT was 12.0 ± 3.5 mm/min, EAPPTT-1 was 15.9 ± 0.7 mm/15 s, and EAPPTT-2 was 15.4 ± 0.4 mm/min (OD) and 17.8 ± 1.0 mm/min (OS). Anterior chamber depth was 1.0 ± 0.1 mm, lens axial length was 2.3 ± 0.1 mm, vitreous chamber depth was 4.3 ± 0.2 mm, and axial globe length was 7.7 ± 0.3 mm. PFL was 11.7 ± 1.7 mm. Intraocular pressure was 11.5 ± 2.8 mmHg for males and 14.0 ± 3.5 mmHg for females (dorsoventral position) and 18.0 ± 3.2 mmHg for males and 24.1 ± 3.0 mmHg for females (ventrodorsal position with inclination of 45°). The ophthalmic parameters reported here can aid in the diagnosis of eye diseases in red-footed tortoises (Chelonoides carbonaria). © 2014 American College of Veterinary Ophthalmologists.

Assessing bone volume for orthodontic miniplate fixation below the maxillary frontal process.

PubMed

Präger, T M; Brochhagen, H G; Mischkowski, R; Jost-Brinkmann, P-G; Müller-Hartwich, R

2014-09-01

The maxillary bone below the frontal process is used for orthodontic anchorage; indications have included skeletally anchored protraction of the maxilla for treating Class III malocclusions or the intrusion of teeth in patients with a deep bite. This study was conducted to assess the condition of bone before cortically implanting miniplates in that area of the maxilla. A total of 51 thin-sliced computed tomography scans of 51 fully-dentate adult patients (mean age 24.0 ± 8.1 years; 27 men and 24 women) obtained prior to third-molar osteotomy were evaluated. Study parameters included total bone thickness, thickness of the facial cortical plate, and width of the nasal maxillary buttress. All these parameters were measured at different vertical levels. The bone volume adjacent to the piriform aperture was most pronounced at the basal level and decreased progressively toward more cranial levels. The basal bone structure had a mean total thickness of 7.8 mm, facial cortical plate thickness of 1.9 mm, and nasal maxillary buttress width of 9.2 mm. At 16 mm cranial to the aperture base, these values fell to 5.6 mm, 1.3 mm, and 5.8 mm, respectively. These bone measurements suggest that screws 7 mm in length can be inserted at the base level of the piriform aperture and screws 5 mm long at the cranial end of the bone.

Embryo developmental events and the egg case of the Aleutian skate Bathyraja aleutica (Gilbert) and the Alaska skate Bathyraja parmifera (Bean).

PubMed

Hoff, G R

2009-02-01

Embryo development events were correlated with egg-case changes for the Aleutian skate Bathyraja aleutica and the Alaska skate Bathyraja parmifera. Yolk absorption underwent two phases: that of steady absorption during early development and that of rapid yolk absorption during the final development stages. Total length (L(T)) for 50% of the pre-hatching embryos egg-case jelly disappearance was 92.04 mm (range 81-102 mm) and 99.36 mm (range 81-100 mm) for B. aleutica and B. parmifera, respectively, allowing the inner chamber to open to seawater flow. The tail filament underwent three phases of growth: rapid elongation during early development (<100 mm embryo L(T)), stasis of tail filament length during the remainder of embryo development and rapid absorption soon after hatching. Complete tail filament development coincided with the disappearance of egg-case jelly. Clasper buds first developed at embryos >70 mm L(T) for both species and the sex ratio was 1:1 well before hatching. Egg cases that were devoid of an ova or developing embryo were c. 5.0 and 6.5% of the egg cases examined for B. aleutica and B. parmifera, respectively. Measurements showed that egg cases containing only egg jelly were smaller in both width and length than those possessing an ova. Embryo stages were punctuated with distinct events that correlated with egg case changes controlling the internal environment of the developing embryo.

Design of an ultra-thin dual band infrared system

NASA Astrophysics Data System (ADS)

Du, Ke; Cheng, Xuemin; Lv, Qichao; Hu, YiFei

2014-11-01

The ultra-thin imaging system using reflective multiple-fold structure has smaller volume and less weight while maintaining high resolution compared with conventional optical systems. The multi-folded approach can significantly extend focal distance within wide spectral range without incurring chromatic aberrations. In this paper, we present a dual infrared imaging system of four-folded reflection with two air-spaced concentric reflective surfaces. The dual brand IR system has 107mm effective focal length, 0.7NA, +/-4° FOV, and 50mm effective aperture with 80mm outer diameter into a 25mm total thickness, which spectral response is 3~12μm.

Effect of varying total mixed ration particle size on rumen digesta and fecal particle size and digestibility in lactating dairy cows.

PubMed

Maulfair, D D; Fustini, M; Heinrichs, A J

2011-07-01

The objective of this experiment was to evaluate the effects of feeding rations of different particle sizes on rumen digesta and fecal matter particle size. Four rumen-cannulated, multiparous, Holstein cows (104±15 d in milk) were randomly assigned to treatments in a 4×4 Latin square design. The diets consisted of 29.4% corn silage, 22.9% ground corn, 17.6% alfalfa haylage, and 11.8% dry grass hay [20% of forage dry matter (DM)] on a DM basis. Dry grass hay was chopped to 4 different lengths to vary the total mixed ration (TMR) particle size. Geometric mean particle sizes of the rations were 4.46, 5.10, 5.32, and 5.84 mm for short, medium, long, and extra long diets, respectively. The ration affected rumen digesta particle size for particles ≥3.35 mm, and had no effect on distribution of particles <3.35 mm. All rumen digesta particle size fractions varied by time after feeding, with soluble particle fractions increasing immediately after feeding and 0.15, 0.6, and 1.18-mm particle size fractions decreasing slightly after feeding. Particle fractions >1.18 mm had ration by time interactions. Fecal neutral detergent fiber (NDF) and indigestible NDF concentrations decreased with increasing TMR particle size. Fecal particle size expressed as total geometric mean particle length followed this same tendency. Fecal particle size, expressed as retained geometric mean particle length, averaged 1.13 mm with more than 36% of particles being larger than 1.18 mm. All fecal nutrient concentrations measured were significantly affected by time after feeding, with NDF and indigestible NDF increasing after feeding and peaking at about 12h later and then decreasing to preprandial levels. Starch concentrations were determined to have the opposite effect. Additionally, apparent digestibility of diet nutrients was analyzed and DM digestibility tended to decrease with increasing TMR particle size, whereas other nutrient digestibilities were not different among rations. These results show that the critical size for increased resistance to rumen escape is larger than 1.18 mm and this critical size is constant throughout the day. This study also concludes that, when using average quality grass hay to provide the range of particle sizes fed, DM digestibility tends to decrease with increasing ration particle size. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Intra-seasonal rainfall characteristics and their importance to the seasonal prediction problem

NASA Astrophysics Data System (ADS)

Tennant, Warren J.; Hewitson, Bruce C.

2002-07-01

Daily station rainfall data in South Africa from 1936 to 1999 are combined into homogeneous rainfall regions using Ward's clustering method. Various rainfall characteristics are calculated for the summer season, defined as December to February. These include seasonal rainfall total, region-average number of station rain days exceeding 1 and 20 mm, region-average of periods between rain days at stations >1 and >20 mm, region-average of wet spell length (sequential days of station rainfall >1 and >20 mm), correlation of daily station rainfall within a region and correlation of seasonal station rainfall anomalies within a region.Rank-ordered rainfall characteristic data generally form an s-shaped curve, and significance testing of discontinuities in these curves suggests that normal rainfall conditions in South Africa consist of a combined middle three quintiles separated from the outer quintiles, rather than the traditional middle tercile.The relationships between the various rainfall characteristics show that seasons with a high total rainfall generally have a higher number of heavy rain days (>20 mm) and not necessarily an increase in light rain days. The length of the period between rain days has a low correlation to season totals, demonstrating that seasons with a high total rainfall may still contain prolonged dry periods. These additional rainfall characteristics are important to end-users, and the analysis undertaken here offers a valuable starting point for seeking physical relationships between rainfall characteristics and the general circulation. Preliminary studies show that the vertical mean wind is related to rainfall characteristics in South Africa. Given that general circulation models capture this part of the circulation adequately, seasonal forecasts of rainfall characteristics become plausible.

Nematode cysts and larvae found in Achatina fulica Bowdich, 1822.

PubMed

Franco-Acuña, D O; Pinheiro, J; Torres, E J L; Lanfredi, R M; Brandolini, S V P B

2009-02-01

This study describes the morphology of the nematode cysts and larvae found in Achatina fulica (giant African snail) in Brazil. Sixty snails were collected in Mesquita, Rio de Janeiro State. Fourteen of the snails were naturally infected. The cysts were spherical, pink colored and measured 0.97 to 1.57 mm in diameter. In the majority of cases they had a single larvae involved in amorphous material. A total of 222 encysted larvae were recovered. Of these, 30 were utilized in the morphological study. The length of the larvae varied from 2.57 to 5.8 mm and they were classified as small--up to 3.5 mm; medium--from 3.53 to 4.5 mm; and large--greater than 4.52 mm. The average length of the larvae in the three groups was 2.85, 3.87 and 5.23 mm, respectively. The larval cuticle was white, shiny and transversally striated until the posterior end of the body. At the anterior end there is a mouth with three lips, with amphids and papillae, followed by a muscular esophagus with average length of 0.61 mm, terminating in an esophageal bulb and having a nerve ring in the middle third of the esophagus, and an intestine with an opening near the posterior end. The tail begins from this opening and has two types of ends: short and abrupt or long and gradually tapering. The difference in the tail end can suggest sexual dimorphism, although no primordial reproductive structures were observed. These characteristics were not sufficient to identify the larvae, so there is a need for further study.

AIM cryocooler developments for HOT detectors

NASA Astrophysics Data System (ADS)

Rühlich, I.; Mai, M.; Withopf, A.; Rosenhagen, C.

2014-06-01

Significantly increased FPA temperatures for both Mid Wave and Long Wave IR detectors, i.e. HOT detectors, which have been developed in recent years are now leaving the development phase and are entering real application. HOT detectors allowing to push size weight and power (SWaP) of Integrated Detectors Cooler Assemblies (IDCA's) to a new level. Key component mainly driving achievable weight, volume and power consumption is the cryocooler. AIM cryocooler developments are focused on compact, lightweight linear cryocoolers driven by compact and high efficient digital cooler drive electronics (DCE) to also achieve highest MTTF targets. This technology is using moving magnet driving mechanisms and dual or single piston compressors. Whereas SX030 which was presented at SPIE in 2012 consuming less 3 WDC to operate a typical IDCA at 140K, next smaller cooler SX020 is designed to provide sufficient cooling power at detector temperature above 160K. The cooler weight of less than 200g and a total compressor length of 60mm makes it an ideal solution for all applications with limited weight and power budget, like in handheld applications. For operating a typical 640x512, 15μm MW IR detector the power consumption will be less than 1.5WDC. MTTF for the cooler will be in excess of 30,000h and thus achieving low maintenance cost also in 24/7 applications. The SX020 compressor is based on a single piston design with integrated passive balancer in a new design achieves very low exported vibration in the order of 100mN in the compressor axis. AIM is using a modular approach, allowing the chose between 5 different compressor types for one common Stirling expander. The 6mm expander with a total length of 74mm is now available in a new design that fits into standard dewar bores originally designed for rotary coolers. Also available is a 9mm coldfinger in both versions. In development is an ultra-short expander with around 35mm total length to achieve highest compactness. Technical solutions and key performance data for AIM's HOT cryocoolers will be presented.

Constraints of body size and swimming velocity on the ability of juvenile rainbow trout to endure periods without food

USGS Publications Warehouse

Simpkins, D.G.; Hubert, W.A.; Martinez Del Rio, C.; Rule, D.C.

2004-01-01

The hypothesis that body size and swimming velocity affect proximate body composition, wet mass and size-selective mortality of fasted fish was evaluated using small (107 mm mean total length, LT) and medium (168 mm mean LT) juvenile rainbow trout Oncorhynchus mykiss that were sedentary or swimming (c. 1 or 2 body lengths-1) and fasted for 147 days. The initial amount of energy reserves in the bodies of fish varied with L T. Initially having less lipid mass and relatively higher mass-specific metabolic rates caused small rainbow trout that were sedentary to die of starvation sooner and more frequently than medium-length fish that were sedentary. Swimming at 2 body length s-1 slightly increased the rate of lipid catabolism relative to 1 body length s-1, but did not increase the occurrence of mortality among medium fish. Death from starvation occurred when fish had <3.2% lipid remaining in their bodies. Juvenile rainbow trout endured long periods without food, but their ability to resist death from starvation was limited by their length and initial lipid reserves. ?? 2004 The Fisheries Society of the British Isles.

Gonad development during the early life of Octopus maya (Mollusca: Cephalopoda).

PubMed

Avila-Poveda, Omar Hernando; Colin-Flores, Rafael Francisco; Rosas, Carlos

2009-02-01

Gonad development during the early life of Octopus maya is described in terms of histological, morphometric, oocytes growth, and somatic-oocyte relationship data obtained from octopus cultured at the UMDI-UNAM, in Sisal, Yucatan, Mexico. This study is the first publication on gonad development during the early life of Octopus maya. A total of 83 O. maya specimens were used; their sizes ranged from 6.5 to 76 mm of total length (TL), 4 to 28 mm of dorsal mantle length (DML), 2.5 to 20 mm of ventral mantle length (VML), and 0.0180 to 7.2940 g of fixed body weight (fBW). Animals were weighed and measured only after preservation. A loss of 10% of living weight was estimated for juvenile octopuses after formalin preservation. The relation of length to weight (VML, DML, TL/fBW) pooled for both sexes had a strong positive correlation (r), as shown by a potential power function that was quite close to 1. Compound images were produced from numerous microscopic fields. The histological examination revealed that, 4 months after hatching, male octopus (24.5 mm DML and 7.2940 g fBW) were in gonad stages 2 (maturing) to 3 (mature), with spermatogonia and spermatocytes in the tubule wall and abundant spermatids and spermatozoa in the central lumen of the seminiferous tubules, suggesting the occurrence of different phases of gonad development at different maturity stages. In contrast, females (22.5 mm DML and 4.8210 g fBW) at the same time since hatching were immature (stage 1), with many oogonia, few oocytes, and germinal epithelium. This suggests that males reach maturity earlier than females, indicating a probable onset of maturity for males at around 4 months of culture or 8 g of wet body weight. Our results indicate the possibility that the size-at-weight can be recognized early with a degree of certainty that allows the sexes to be separated for culture purposes; but more detailed studies on reproduction in relation to endocrinology and nutrition are needed.

Effect of customization of master gutta-percha cone on apical control of root filling using different techniques: an ex vivo study.

PubMed

van Zyl, S P; Gulabivala, K; Ng, Y-L

2005-09-01

(i) To compare the prevalence of extrusion of root filling material when placed using different root filling techniques, with or without customization of the master gutta-percha (GP) cone; and (ii) to investigate the effects of some factors influencing root filling extrusion and presence of voids. A total of 180 roots were selected, prepared and randomly allocated to three groups. Five general dental practitioners performed the root fillings; each filled one group of roots (n = 60) using each of three techniques; 'cold lateral compaction' (n = 20), 'warm vertical compaction' (n = 20) and 'continuous-wave' (n = 20) techniques. For each obturation technique, the master GP cone was customized using chloroform in 10 samples. Two groups of the roots were recycled to allow all five operators to fulfill their remit. Two observers, blind to operator and obturation technique, examined the radiographs (master apical file, post-obturation) to determine the presence of root filling extrusion and voids within the apical 5 mm, independently. Root filling extrusion was also confirmed by direct inspection of the root apex after obturation. The data were analysed using logistic regression models. A total of 300 root fillings were performed; nine were excluded from the analysis. Most of the root fillings (80%, n = 233) were placed within 0.5 mm of the working length; only 20% (n = 58) were placed >0.5 mm beyond the working length. The odds of prevalence of extrusion (>0.5 mm) were significantly reduced by about 50% when cold lateral compaction or customization of GP were used. One operator produced 2.5 times more extruded root fillings than others. Curvature & length of root canal, apical size of prepared canal, as well as operator's preferred obturation technique had no significant influence on the prevalence of extrusion. Customization of GP was the sole factor to significantly reduce the prevalence of voids within the apical 5 mm of working length. Root filling extrusion was significantly influenced by 'operator' and was reduced by cold lateral compaction and customization of the master cone. Customization of master cone was the only factor that reduced voids apically.

Tumor response and negative distal resection margins of rectal cancer after hyperthermochemoradiation therapy.

PubMed

Tsutsumi, Soichi; Tabe, Yuichi; Fujii, Takaaki; Yamaguchi, Satoru; Suto, Toshinaga; Yajima, Reina; Morita, Hiroki; Kato, Toshihide; Shioya, Mariko; Saito, Jun-Ichi; Asao, Takayuki; Nakano, Takashi; Kuwano, Hiroyuki

2011-11-01

The safety of regional hyperthermia has been tested in locally advanced rectal cancer. The aim of this study was to assess the effects of shorter distal margins on local control and survival in rectal cancer patients who were treated with preoperative hyperthermochemoradiation therapy (HCRT) and underwent rectal resection by using the total mesorectal excision (TME) method. Ninety-three patients with rectal adenocarcinoma who received neoadjuvant HCRT (total radiation: 50 Gy) were included in this study. Surgery was performed 8 weeks after HCRT, and each resected specimen was evaluated histologically. Length of distal surgical margins, status of circumferential margins, pathological response, and tumor node metastasis stage were examined for their effects on recurrence and survival. Fifty-eight (62.4%) patients had tumor regression, and 20 (21.5%) had a pathological complete response. Distal margin length ranged from 1 to 55 mm (median, 21 mm) and did not correlate with local recurrence (p=0.57) or survival (p=0.75) by univariate analysis. Kaplan-Meier estimates of recurrence-free survival and local recurrence for the <10 mm versus ≥10 mm groups were not significantly different. Positive circumferential margins and failure of tumors to respond were unfavorable factors in survival. Distal resection margins that are shorter than 10 mm but are not positive appear to be equivalent to longer margins in patients who undergo HCRT followed by rectal resection with TME. To improve the down-staging rate, additional studies are needed.

Predictors of short term treatment outcome in patients with achalasia following endoscopic or surgical therapy.

PubMed

Gheorghe, Cristian; Bancila, Ion; Tutuian, Radu; Iacob, Razvan; Tomulescu, Victor

2012-01-01

Pneumatic balloon dilation and surgical myotomy are the most effective treatments for achalasia. While there is controversy which method is best, the aim of the current study was to identify predictors of symptom recurrence after endoscopic or surgical therapy. Patients undergoing pneumatic balloon dilatation (30mm) or laparoscopic Heller myotomy with Dor fundoplication were included in the study. Analyzed parameters include total symptom score (sum of 0-5 point intensity for dysphagia, regurgitation and chest pain), width and height of esophageal column at 2 and 5 minutes after oral barium ingestion, lower esophageal sphincter (LES) length, resting (LESP) and residual pressure (LESRP) before and 3 months after intervention. Patients with symptoms score <3 at the 3-month follow-up visit were considered asymptomatic. Twenty-one patients underwent pneumatic dilation (14) or laparoscopic myotomy (7). Total symptom score improved (p<0.01) from pre- (7.2±2.7) to post-intervention (1.7±2.6). Eleven (85.8%) patients in the endoscopic group vs. 7 (100%) patients in the surgical group were symptom-free 3 months after intervention. Therapies improved LESP (24.4±8.2mmHg pre- vs. 15.4±10.3mmHg post-therapy; p=0.003) and mean LESRP (7.9±4.3mmHg pre- vs. 5.3±6.7mmHg post-therapy; p=0.03). Univariate linear regression analysis identified barium contrast column width >5cm at 2 minutes (p=0.04), LES length <2cm (p=0.003) and LESRP >10mmHg (p=0.02) as predictors for persistent symptoms. While >85% of achalasia patients responded well to 30mm pneumatic balloon dilation, patients with elevated LES pressure, short LES and wide esophagus should be considered as primary surgical candidates.

Antioxidant responses of chickpea plants subjected to boron toxicity.

PubMed

Ardic, M; Sekmen, A H; Tokur, S; Ozdemir, F; Turkan, I

2009-05-01

This study investigated oxidative stress and the antioxidant response to boron (B) of chickpea cultivars differing in their tolerance to drought. Three-week-old chickpea seedlings were subjected to 0.05 (control), 1.6 or 6.4 mm B in the form of boric acid (H(3)BO(3)) for 7 days. At the end of the treatment period, shoot length, dry weight, chlorophyll fluorescence, B concentration, malondialdehyte content and the antioxidant enzymes superoxide dismutase (SOD), peroxidase (POX), catalase (CAT), ascorbate peroxidase (APX) and glutathione reductase (GR) were measured. The 1.6 mm B treatment did not cause significant changes in shoot length of cultivars, although shoot length increased in the drought-tolerant Gökce and decreased in the drought-sensitive Küsmen after 6.4 mm B treatment. Dry weights of both cultivars decreased with 6.4 mm B treatment. Chlorophyll fluorescence (Fv/Fm) did not change in Gökce at either B level. Nor did it change in Küsmen with 1.6 mm B but Fv/Fm decreased with 6.4 mm B. Boron concentration in the shoots of both cultivars increased significantly with increasing levels of applied B. Significant increases in total SOD activity were observed in shoots of both cultivars given 1.6 and 6.4 mm B. Shoot extracts exhibited five activity bands, two of which were identified as MnSOD and Cu/ZnSOD. In comparison to the control group, all enzyme activities (except APX and SOD) decreased with 1.6 mm B stress. GR activity decreased, while activities of CAT, POX and APX did not change with 6.4 mm B in Küsmen. On the other hand, activities of CAT, APX and SOD increased in Gökce at both B levels. In addition, lipid peroxidation was higher in Küsmen than in Gökce, indicating more damage by B to membrane lipids in the former cultivar. These results suggest that (i) Gökce is tolerant and Küsmen is sensitive to B, and (ii) B tolerance of Gökce might be closely related to increased capacity of the antioxidative system (total SOD, CAT and APX) to scavenge reactive oxygen species and thus suppress lipid peroxidation under B stress. To the best of our knowledge, this is the first report on the antioxidant response of chickpea seedlings to B toxicity.

Mechatronic design of a fully integrated camera for mini-invasive surgery.

PubMed

Zazzarini, C C; Patete, P; Baroni, G; Cerveri, P

2013-06-01

This paper describes the design features of an innovative fully integrated camera candidate for mini-invasive abdominal surgery with single port or transluminal access. The apparatus includes a CMOS imaging sensor, a light-emitting diode (LED)-based unit for scene illumination, a photodiode for luminance detection, an optical system designed according to the mechanical compensation paradigm, an actuation unit for enabling autofocus and optical zoom, and a control logics based on microcontroller. The bulk of the apparatus is characterized by a tubular shape with a diameter of 10 mm and a length of 35 mm. The optical system, composed of four lens groups, of which two are mobile, has a total length of 13.46 mm and an effective focal length ranging from 1.61 to 4.44 mm with a zoom factor of 2.75×, with a corresponding angular field of view ranging from 16° to 40°. The mechatronics unit, devoted to move the zoom and the focus lens groups, is implemented adopting miniature piezoelectric motors. The control logics implements a closed-loop mechanism, between the LEDs and photodiode, to attain automatic control light. Bottlenecks of the design and some potential issues of the realization are discussed. A potential clinical scenario is introduced.

Quantitative proteomics analysis with iTRAQ in human lenses with nuclear cataracts of different axial lengths.

PubMed

Zhou, Haiyan; Yan, Hong; Yan, Weijia; Wang, Xinchuan; Ma, Yong; Wang, Jianping

2016-01-01

The goal of this study was to identify and quantify the differentially expressed proteins in human nuclear cataract with different axial lengths. Thirty-six samples of human lens nuclei with hardness grade III or IV were obtained during cataract surgery with extracapsular cataract extraction (ECCE). Six healthy transparent human lens nuclei were obtained from fresh healthy cadaver eyes during corneal transplantation surgery. The lens nuclei were divided into seven groups (six lenses in each group) according to the optic axis: Group A (mean axial length 28.7±1.5 mm; average age 59.8±1.9 years), Group B (mean axial length 23.0±0.4 mm; average age 60.3±2.5 years), Group C (mean axial length 19.9±0.5 mm; average age 55.1±2.5 years), Group D (mean axial length 28.7±1.4 mm; average age 58.0±4.0 years), Group E (mean axial length 23.0±0.3 mm; average age 56.9±4.2 years), and Group F (mean axial length 20.7±0.6 mm; average age 57.6±5.3 years). The six healthy transparent human lenses were included in a younger group with standard optic axes, Group G (mean axial length 23.0±0.5 mm; average age 34.7±4.2 years).Water-soluble, water-insoluble, and water-insoluble-urea-soluble protein fractions were extracted from the samples. The three-part protein fractions from the individual lenses were combined to form the total proteins of each sample. The proteomic profiles of each group were analyzed using 8-plex isobaric tagging for relative and absolute protein quantification (iTRAQ) labeling combined with two-dimensional liquid chromatography tandem mass spectrometry (2D-LC-MS/MS). The data were analyzed with ProteinPilot software for peptide matching, protein identification, and quantification. Differentially expressed proteins were validated with western blotting. We employed biological and technical replicates and selected the intersection of the two sets of results, which included 40 proteins. From the 40 proteins identified, six were selected as differentially expressed proteins closely related to axial length. The six proteins were gap junction alpha-3 protein, beta-crystallin B2, T-complex protein 1 subunit beta, gamma-enolase, pyruvate kinase isozymes M1/M2, and sorbitol dehydrogenase. Levels of beta-crystallin B2 expression were decreased in nuclear cataracts with longer axial length. The results of the mass spectrometric analysis were consistent with the western blot validation. The discovery of these differentially expressed proteins provides valuable clues for understanding the pathogenesis of axial-related nuclear cataract. The results indicate that beta-crystallin B2 (CRBB2) may be involved in axial-related nuclear cataract pathogenesis. Further studies are needed to investigate the correlation between CRBB2 and axial-related nuclear cataract.

Emergence, development, and maturity of the gonad of two species of chitons "sea cockroach" (Mollusca: Polyplacophora) through the early life stages.

PubMed

Avila-Poveda, Omar Hernando; Abadia-Chanona, Quetzalli Yasú

2013-01-01

This study describes and recognises, using histological and microscopical examinations on a morphometrical basis, several gonad traits through the early life stages of Chiton articulatus and C. albolineatus. Gonadal ontogenesis, gonad development stages, sexual differentiation, onset of the first sexual maturity, and growth sequences or "early life stages" were determined. In addition, allometry between lengths and body weight pooled for both sexes per each chiton were calculated using equation Y = aX(b) . A total of 125 chitons (4≤TL≤40 mm, in total length "TL") were used. All allometric relations showed a strong positive correlation (r), close to 1, with b-values above three, indicating an isometric growth. Gonadal ontogenesis and gonad development stages were categorised into three periods ("Pw" without gonad, "Pe" gonad emergence, and "Pf" gonadal sac formed) and four stages ("S0" gametocytogenesis, "S1" gametogenesis, "S2" mature, and "S3" spawning), respectively. Compound digital images were attained for each process. Periods and stages are overlapped among them and between species, with the following overall confidence intervals in TL: Pw 6.13-14.32 mm, Pe 10.32-16.93 mm, Pf 12.99-25.01 mm, S0 16.08-24.34 mm (females) and 19.51-26.60 mm (males), S1 27.15-35.63 mm (females) and 23.45-32.27 mm (males), S2 24.48-40.24 mm (females) and 25.45-32.87 mm (males). Sexual differentiation (in S0) of both chitons occurs first as a female then as a male; although, males reach the onset of the first sexual maturity earlier than females, thus for C. articulatus males at 17 mm and females at 32 mm, and for C. albolineatus males at 23.5 mm and females at 28 mm, all in TL. Four early life stages (i.e., subjuvenile, juvenile, subadult, and adult) are described and proposed to distinguish growth sequences. Our results may be useful to diverse disciplines, from developmental biology to fisheries management.

Growth and contribution of stocked channel catfish, Ictalurus punctatus (Rafinesque, 1818): the importance of measuring post-stocking performance

USGS Publications Warehouse

Stewart, David R.; Long, James M.

2015-01-01

In this study it was sought to quantify post-stocking growth, survival, and contribution of advanced size (178 mm total length [TL]) channel catfish Ictalurus punctatus fingerlings, something rarely done. Channel catfish populations were evaluated before (May 2010) and after (May to August 2011 and 2012) stocking. Relative abundance, stocking contribution, and growth were different (P < 0.05) in the two study impoundments (lakes Lone Chimney and Greenleaf, Oklahoma). For fish stocked in Lake Lone Chimney, stocking contribution was lower (3–35%), and average length and weight of stocked fish by age-2 reached 230 mm TL and 85 g, whereas the stocking contribution (84–98%) and growth in length (340 mm TL) and weight (280 g) were higher by age-2 in Lake Greenleaf. Given these unambiguous differences of post-stocking performance, benchmark metrics that represent population-level information such as relative abundance and average length and weight of the sample masked these significant differences, highlighting the importance of marking hatchery-fish and then following them through time to determine the effectiveness of stocking. These results suggest that stock enhancement programmes would benefit from studies that quantify post-stocking performance of hatchery fish.

[Reproductive effort, fattening index and yield of Arca zebra (Filibranchia: Arcidae) by length and its association with environmental variables, Sucre, Venezuela].

PubMed

Lista, María; Velásquez, Carlos; Prieto, Antulio; Longart, Yelipza

2016-06-01

Arca zebra is a mollusk of commercial value and a major socioeconomic fishery in Northeastern Venezuela. The present study aimed to evaluate the reproductive effort (RE), fattening index (FI) and yield (Y) in different size groups of A. zebra from the morro Chacopata, Venezuela. For this, monthly samplings from June 2008 and June 2009, were undertaken, and the bivalves obtained were distributed in three length groups: I (30.1 to 50.0 mm), II (50.1 to 70.0 mm) and III (> 70.0 mm). Monthly RE, FI and Y were determined based on bivalve changes in volume of fresh meat (VFM), intervalvar volume (IV), dry gonad biomass (DW), dry biomass of the organism without gonad (DWs), fresh biomass of meat (FBM) and total biomass including shell (TBIS). Besides, environmental variables such as temperature, salinity, dissolved oxygen, total organic and inorganic seston and chlorophyll a were measured monthly. There was great variation in the DW between length groups (relevant for II and III): increased from June until late September 2008, was followed by a marked decrease in October 2008, recovered in the following months, and decreased in January 2009, with a slight increase until May 2009; these changes were associated with variations in sea temperature. The weight of the gonad (DW) influenced the RE, FI and Y, as these reached their peaks in the months where there was higher gonadal production, indicating the influence of temperature on A. zebra reproduction.

Reproductive biology of the spotback skate Atlantoraja castelnaui in the south-west Atlantic Ocean.

PubMed

Colonello, J C; García, M L; Lasta, C A; Menni, R C

2012-06-01

This study provides information on the reproduction of spotback skate Atlantoraja castelnaui. A total of 232 individuals (119 females and 113 males) were obtained from surveys carried out between 2003 and 2006, from the south-west Atlantic Ocean, between 34 and 42° S and <50 m deep; another 514 specimens (241 females and 273 males) were obtained between 2005 and 2007 from commercial fishery operations carried out in the same area and landings in the port of Mar del Plata, Argentina. Males ranged from 185 to 1250 mm total length (L(T) ) and females from 243 to 1368 mm L(T) . Length at maturity was estimated to be 980 mm for males and 1089 mm L(T) for females. Lack of variation of testis mass together with the continuous production of mature spermatocyst and spermatozoa in deferent ducts suggested that males can reproduce throughout the year. Females reproduced year-round with peaks of reproductive activity an integral part of a continuous cycle. This conclusion is corroborated by the seasonal variation of ovaries, oviducal gland and the occurrence of females with eggs in the uterus throughout the year. Results from this study indicate that A. castelnaui is very susceptible to fishery pressure. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

Persistence of identifiable remains of white sturgeon juveniles in digestive tracts of northern pikeminnow

USGS Publications Warehouse

Gadomski, D.M.; Frost, C.N.

2004-01-01

Juvenile white sturgeon, Acipenser transmontanus, have not been commonly identified as prey items in digestive tracts of fishes collected in the wild. In particular, the diet of northern pikeminnow, Ptychocheilus oregonensis, an abundant Pacific Northwest freshwater predator which has been widely studied, has not included juvenile white sturgeon. To aid in interpreting these results and help in planning future feeding studies, we determined the persistence of identifiable remains of white sturgeon juveniles in this predator's digestive tract. Northern pikeminnow (mean total length = 476 mm), were force-fed meals of 2 or 3 juvenile white sturgeon (mean total length = 91 mm). After digestive periods of 4, 8, 16, 24, 28, and 32h at a water temperature of about 17 ??C, fish were sacrificed, digestive tracts removed, and contents examined. Our results indicate that juvenile white sturgeon would be readily discernable in digestive tracts of northern pikeminnow at least a day after feeding, with scutes remaining undigested and identifiable for 28 h.

Pelvic bone asymmetry in 323 study participants receiving abdominal CT scans.

PubMed

Badii, Maziar; Shin, Sonya; Torreggiani, William C; Jankovic, Bojana; Gustafson, Paul; Munk, Peter L; Esdaile, John M

2003-06-15

Retrospective review of all CT scans of pelvis and abdomen performed at our institution in October and November 2000. To determine the prevalence and extent of radiographic pelvic asymmetry in a population of patients not preselected for having low back pain. Pelvic asymmetry refers to asymmetric positioning of landmarks on the two sides of the pelvis and may have a structural or functional etiology. Pelvic asymmetry can be associated with the presence of true leg length discrepancy, lead to false diagnosis or inaccurate measurement of leg length discrepancy, or itself be independently associated with back pain. Although the prevalence of pelvic asymmetry has been reported in patients with back pain to be 24-91%, its prevalence in the general population is not known. A total of 323 consecutive CT scans of the pelvis/abdomen were assessed for pelvic asymmetry by one of three examiners. Pelvic asymmetry was defined as an unequal distance from the iliac crests to the acetabuli bilaterally, measured on the anteroposterior scout view of the CT scan. Measurements made on 30 randomly selected scans by the three examiners were used to assess interrater reliability of the measurement method. Pelvic asymmetry ranged in magnitude from -11 mm to 7 mm [right pelvis (mm) - left pelvis (mm)]. Pelvic asymmetry was >5 mm in 17 of 323 (5.3%) and >10 mm in 2 of 323 (0.6%) of the subjects; 172 of 323 (53.3%) had a smaller right hemipelvis (mean asymmetry = -3.0 mm). A total of 95 of 323 (29.4%) had a smaller left hemipelvis (mean asymmetry = 2.1 mm). The intraclass correlation coefficient [ICC(2,1)] between the three observers was high (0.91). Pelvic asymmetry of >5 mm was uncommon, with a prevalence of approximately 5% in the population studied. CT scanography was found to be a practical and reliable method for the assessment of suspected pelvic asymmetry.

A retrospective study of sintered porous-surfaced dental implants in restoring the edentulous posterior mandible: up to 9 years of functioning.

PubMed

Sohn, Dong-Seok; Kim, Woo-Sung; Lee, Won-Hyuk; Jung, Heui-Seung; Shin, Im-Hee

2010-10-01

The aim of this retrospective study was to evaluate the survival rate of sintered porous-surfaced implants placed in the edentulous posterior mandibles, in relation to implant length and diameter, crown-to-implant ratio, and types of prostheses, for a maximum of 9 years of functioning (mean: 55.8 months; range: 5-108 months). The study group consisted of 43 partially edentulous patients who visited Catholic University Hospital of Daegu and 1 private dental clinic. A total of 122 sintered porous-surfaced implants--Endopore (Innova Life Sciences, Toronto, Ontario, Canada)--were placed in the edentulous posterior mandibles. Two diameter sizes (4.1 and 5.0 mm) and 4 lengths (5.0, 7.0, 9.0, and 12.0 mm) were used. All implants were restored with fixed prostheses. One hundred three implants were splinted and 21 implants were nonsplinted. Panoramic views and periapical radiographs were taken at the time of the first, postoperative, crown placement, and following checkup visits. The survival rates of the implants in relation to length, diameter, crown-to-implant ratio, and types of prostheses were investigated. Statistical data were analyzed using SPSS Win.Ver 14.0 software with the χ² test. The survival rate of the 4.1-mm-diameter implants was 100% and 91.2% for the 5.0-mm-diameter implants. The survival rates of the implants of differing diameters were found to be statistically different (P = 0.005). The survival rates of both the 5.0-mm and 7.0-mm-length implants were 100%. The survival rate of the 9.0-mm-length implants was 97.9% and for the 12.0-mm-length implants was 95.1%. There was no statistical difference in survival rates for the differing lengths of implants. Of the 103 prostheses that were splinted, the survival rate was 98.0%. The survival rate of splinted prostheses was higher than that of the nonsplinted prostheses but was found to be not statistically different. There were no failed cases when the crown-to-implant ratio was <1.0. When the crown-to-implant ratio was between 1.0 and 1.4, the failure rate of the implants was 6.7%. No failure was recorded with the ratio range of 1.5 to 2.0. Relative to the crown-to-implant ratio of 1.0, the failure rates were statistically different (P = 0.048). The cumulative survival rate of the porous-surfaced implants placed in the edentulous posterior mandibles was 97.5%. Short porous-surfaced implants showed satisfactory results after a maximum of 9 years of functioning in the edentulous posterior mandibles.

Influence of chronic total occlusions on coronary artery bypass graft surgical outcomes.

PubMed

Banerjee, Subhash; Master, Ryan G; Peltz, Matthias; Willis, Bernice; Mohammed, Atif; Little, Bertis B; DiMaio, Michael J; Jessen, Michael E; Brilakis, Emmanouil S

2012-11-01

Presence of epicardial coronary artery chronic total occlusion (CTO) predicts higher referral rates for coronary bypass graft surgery (CABG). However, the impact of coronary artery CTO on CABG outcomes has never been systematically studied. We examined one-year outcomes in 605 consecutive Veterans, discharged post-CABG between June 2005 and December 2008. A coronary CTO was present in 256 patients (42%), predominantly (48.3%) in the right coronary artery distribution. Baseline clinical characteristics and medical therapy were similar in patients with and without a coronary CTO. A single CTO was present in 73.8%, and 26.2% patients had multiple CTO. All left anterior descending coronary artery CTO were successfully bypassed, as were >92% in left circumflex and right coronary arteries and 85% CTO in multiple coronary artery distributions. During the mean follow-up of 348.9 ± 4.5 days, incidence of all-cause death and myocardial infarction were similar in both groups (7.1% in CTO group and 7.4% in non-CTO group; p = 0.97). CTO >20 mm in length constituted 74.9% and >40 mm 37.8%. One-year survival post-CABG was significantly lower in patients with CTO lengths >40 mm compared to ≤20 mm (p = 0.04). CTO >40 mm was an independent predictor of post-CABG mortality controlling for age, number of CTO, comorbid diseases, clopidogrel use, severity of coronary artery disease, renal failure, and left ventricular ejection fraction. CABG achieves high success in grafting epicardial coronary vessels with CTO; however, presence of long coronary CTO (>40 mm) is an independent predictor of post-CABG survival. © 2012 Wiley Periodicals, Inc.

[Ultrasonographic evaluation of the uterine cervix length remaining after LOOP-excision].

PubMed

Robert, A-L; Nicolas, F; Lavoué, V; Henno, S; Mesbah, H; Porée, P; Levêque, J

2014-04-01

To assess whether there is a correlation between the length of a conization specimen and the length of the cervix measured by vaginal ultrasonography after the operation Prospective observational study including patients less than 45 years with measurement of cervical length before and the day of the conization, and measuring the histological length of the specimen. Among the 40 patients enrolled, the average ultrasound measurements before conization was 26.9 mm (± 4.9 mm) against 18.1mm (± 4.4mm) after conization with a mean difference of 8.8mm (± 2.4mm) (difference statistically significant P<.0001). The extent of histological specimen was 9 mm (± 2.2mm) on average. A correlation between ultrasound and histological measurements with a correlation coefficient R=0.85 was found statistically significant (P<0.0001). Moreover, the rate of cervix length remove by loop-excision in our series is 33% (± 8.5%). A good correlation between the measurements of the specimen and the cervical ultrasound length before and after conization was found, as a significant reduction in cervical length after conization. The precise length of the specimen should be known in case of pregnancy and the prevention of prematurity due to conization rests on selected indications and efficient surgical technique. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

Continuous Effect of Radial Resection Margin on Recurrence and Survival in Rectal Cancer Patients Who Receive Preoperative Chemoradiation and Curative Surgery: A Multicenter Retrospective Analysis.

PubMed

Sung, SooYoon; Kim, Sung Hwan; Lee, Joo Hwan; Nam, Taek Keun; Jeong, Songmi; Jang, Hong Seok; Song, Jin Ho; Lee, Jeong Won; Bae, Jung Min; Lee, Jong Hoon

2017-07-01

To elucidate the proper length and prognostic value of resection margins in rectal cancer patients who received preoperative chemoradiotherapy (CRT) followed by curative total mesorectal excision (TME). A total of 1476 rectal cancer patients staging cT3-4N0-2M0 were analyzed. All patients received radiation dose of 50.4 Gy in 28 fractions with concurrent 5-fluorouracil or capecitabine. Total mesorectal excision was performed 4 to 8 weeks after radiation therapy. The recurrence-free survival (RFS) at 5 years showed a significant difference between 3 groups: patients with circumferential resection margin (CRM) ≤1 mm, CRM 1.1 to 5 mm, and CRM >5 mm (46.2% vs 68.6% vs 77.5%, P<.001). Patients with CRM ≤1 mm showed a significantly higher cumulative incidence of locoregional recurrence (P<.001) and distant metastasis (P<.001) at 5 years compared with the other 2 groups. Patients with CRM 1.1 to 5 mm showed a significantly higher cumulative incidence of distant metastasis (P<.001), but not locoregional recurrence (P=.192), compared with those with CRM >5 mm. Distal resection margin (≤5 vs >5 mm) did not show any significant difference in cumulative incidence of locoregional recurrence (P=.310) and distant metastasis (P=.926). Rectal cancer patients with CRM ≤1 mm are a high-risk group, with the lowest RFS. Patients with CRM 1.1 to 5 mm may be at intermediate risk, with moderately increased distant recurrence. Distal resection margin was not significantly associated with RFS in rectal cancer after neoadjuvant CRT and total mesorectal excision. Copyright © 2017 Elsevier Inc. All rights reserved.

Ocular refractive and biometric characteristics in patients with thalassaemia major.

PubMed

Nowroozzadeh, Mohammad Hosein; Kalantari, Zahra; Namvar, Khadije; Meshkibaf, Mohammad Hassan

2011-07-01

Thalassaemia major is associated with characteristic findings in craniofacial bony structures and thereby may render abnormal bony orbit and subsequently distinctive ocular biometry. The purpose of the present study was to evaluate the ocular refractive and biometric characteristics in patients with thalassaemia major. This case-controlled study comprised 94 eyes of 47 patients with thalassaemia major and 88 eyes of 44 age- and sex-matched healthy control subjects. All participants had a complete ocular examination including slitlamp biomicroscopy, fundoscopy, ocular biometry, keratometry, refraction and analysis using Fourier transformation. There were no significant differences in spherical equivalent (p = 0.66) and total astigmatism (p = 0.83) between groups. Mean uncorrected vision and visual acuities (logMar) were similar (p = 0.32 and p = 0.71, respectively). Compared with controls, thalassaemic patients had a shorter axial length (23.01 ± 0.12 [SEM] mm versus 23.46 ± 0.12 mm, p = 0.035), thicker crystalline lens (4.01 ± 0.11 mm versus 3.87 ± 0.1 mm, p = 0.046) and steeper average keratometry (44.02 ± 0.24 D versus 43.44 ± 0.24, p = 0.03). Fifty-seven per cent of thalassaemic patients had against-the-rule astigmatism (total), while 64.6 per cent of controls showed a with-the-rule pattern (p < 0.05). These patterns were also found for corneal astigmatism. The magnitudes of total, corneal and lenticular astigmatism were similar among groups. Regression analysis showed significant correlation between corneal (J0 and J45) and total (J0 and J45) astigmatism. The correlations were less prominent between lenticular and total J0 and J45. The mean intraocular pressure was 14.68 ± 0.27 mmHg and 13.3 ± 0.26 mmHg in the thalassaemia and control groups, respectively (p < 0.001). Six eyes (12.8 per cent) of four patients in the thalassaemia group had posterior subcapsular cataract, while the condition had not been observed in controls (p = 0.049). Shorter axial length, thicker lens, steeper corneal curvature and more against-the-rule pattern were characteristic findings in patients with thalassaemia major. © 2011 The Authors. Clinical and Experimental Optometry © 2011 Optometrists Association Australia.

Development of Flexible Extremities Protection utilizing Shear Thickening Fluid/Fabric Composites

DTIC Science & Technology

2012-01-19

absorption frequencies. With the addition of Gluta, the peak for each of the three bonds increased indicating that the total number of bonds (i.e., cross...fiber to be investigated a gage length of 127 mm. The fiber was clamped at one end and at a position of 127 mm at that end. A Celanese food ...general behavior of high performance fibers during cut resistance testing at normal incidence with a Celanese food processing blade. This data is the

Electronic working length determination in primary teeth by ProPex and Digital Signal Processing.

PubMed

Nelson-Filho, Paulo; Lucisano, Marcela Pacífico; Leonardo, Mário Roberto; da Silva, Raquel Assed Bezerra; da Silva, Léa Assed Bezerra

2010-12-01

The purpose of this study was to evaluate the accuracy of electronic apex locators Digital Signal Processing (DSP) and ProPex, for root canal length determination in primary teeth. Fifteen primary molars (a total of 34 root canals) were divided into two groups: Group I - without physiological resorption (n = 16); and Group II - with physiological resorption (n = 18). The length of each canal was measured by introducing a file until its tip was visible and then it was retracted 1 mm. For electronic measurement, the devices were set to 1 mm short of the apical resorption. The data were analysed statistically using the intraclass correlation coefficient (ICC). Results showed that the ICC was high for both electronic apex locators in all situations - with (ICC: DSP = 0.82 and Propex = 0.89) or without resorption (ICC: DSP = 0.92 and Propex = 0.90). Both apex locators were extremely accurate in determining the working length in primary teeth, both with or without physiological resorption. © 2010 The Authors. Australian Endodontic Journal © 2010 Australian Society of Endodontology.

Morphometric analysis of the proximal ulna using three-dimensional computed tomography and computer-aided design: varus, dorsal, and torsion angulation.

PubMed

Yong, Woon Jae; Tan, Jun; Adikrishna, Arnold; Lee, Hyun Joo; Jung, Jin Woo; Cho, Dong-Woo; Jeon, In-Ho

2014-10-01

The proximal ulna, particularly the course of the posterior border, has a complex three-dimensional (3D) morphology which has been highlighted recently due to its clinical relevance in relation to surgical treatments. 3D computed tomography (CT) reconstruction and computer-aided design (CAD) based software can help to visualize the complex anatomy and thus aid the investigation of the more detailed morphology of the proximal ulna. In our current study, 3D CT reconstruction images of 20 cadavers were imported into the 3D CAD program. Three morphologic angle parameters of the proximal ulna were measured including the dorsal, varus and torsion angulation. The torsion angulation was measured using the flat spot of olecranon dorsal aspect. We measured the total length of the ulna and the distance between the olecranon tip and the apex of dorsal and varus angulation. Furthermore, the thickness of olecranon was also measured for all the specimens. The results showed that the mean dorsal, varus, and torsion angulation was 4.3° (range 2.6°-5.9°), 12.1° (range 7.9°-17.6°), and 22.5° (range 16.6°-30.5°), respectively. The average length ratio of the dorsal and varus angulation apex to the total ulnar length was 26.4 % (range 19.8-30.7 %) and 32.7 % (range 27.5-37.5 %), respectively. The average of olecranon thickness at the proximal tip, mid-olecranon fossa, and at coronoid tip level was 17.8 mm (range 14.1-22.8 mm), 19.7 mm (range 15.8-23.1 mm), and 35.1 mm (range 27.9-41.8 mm), respectively. In conclusion, variations in the proximal ulna have to be considered when anatomically contoured dorsal plates are applied. Knowledge of the 3D morphologic anatomy of the proximal ulna would provide important information on fracture reductions, and the design of a precontoured dorsal plate or a prosthetic ulnar stem.

Quantitative evaluation of the relationship between dorsal wall length, sole thickness, and rotation of the distal phalanx in the bovine claw using computed tomography.

PubMed

Tsuka, T; Murahata, Y; Azuma, K; Osaki, T; Ito, N; Okamoto, Y; Imagawa, T

2014-10-01

Computed tomography (CT) was performed on 800 untrimmed claws (400 inner claws and 400 outer claws) of 200 pairs of bovine hindlimbs to investigate the relationships between dorsal wall length and sole thickness, and between dorsal wall length and the relative rotation angle of distal phalanx-to-sole surface (S-D angle). Sole thickness was 3.8 and 4.0 mm at the apex of the inner claws and outer claws, respectively, with dorsal wall lengths <70 mm. These sole thickness values were less than the critical limit of 5 mm, which is associated with a softer surface following thinning of the soles. A sole thickness of 5 mm at the apex was estimated to correlate with dorsal wall lengths of 72.1 and 72.7 mm for the inner and outer claws, respectively. Sole thickness was 6.1 and 6.4 mm at the apex of the inner and outer claws, respectively, with dorsal wall lengths of 75 mm. These sole thickness values were less than the recommended sole thickness of 7 mm based on the protective function of the soles. A sole thickness >7 mm at the apex was estimated to correlate with a dorsal wall length of 79.8 and 78.4mm for the inner and outer claws, respectively. The S-D angles were recorded as anteversions of 2.9° and 4.7° for the inner and outer claws, respectively, with a dorsal wall length of 75 mm. These values indicate that the distal phalanx is likely to have rotated naturally forward toward the sole surface. The distal phalanx rotated backward to the sole surface at 3.2° and 7.6° for inner claws with dorsal wall lengths of 90-99 and ≥100 mm, respectively; and at 3.5° for outer claws with a dorsal wall length ≥100 mm. Dorsal wall lengths of 85.7 and 97.2 mm were estimated to correlate with a parallel positional relationship of the distal phalanx to the sole surface in the inner and outer claws, respectively. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serkland, Darwin K.; So, Haley M.; Peake, Gregory M.

Here, we report on mode selection and tuning properties of vertical-external-cavity surface-emitting lasers (VECSELs) containing coupled semiconductor and external cavities of total length less than 1 mm. Our goal is to create narrowlinewidth (<1MHz) single-frequency VECSELs that operate near 850 nm on a single longitudinal cavity resonance and tune versus temperature without mode hops. We have designed, fabricated, and measured VECSELs with external-cavity lengths ranging from 25 to 800 μm. Lastly, we compare simulated and measured coupled-cavity mode frequencies and discuss criteria for single mode selection.

Influence of different length of core suture purchase among suture row on the strength of 6-strand tendon repairs.

PubMed

Okubo, Hirotaka; Kusano, Nozomu; Kinjo, Masaki; Kanaya, Fuminori

2015-01-01

In multi-strand suture methods consisting of several suture rows, the different length of core suture purchase between each suture row may affect the strength of repairs. We evaluated the influence of the different length of core suture purchase between each suture row on the strength of 6-strand tendon repairs. Rabbit flexor tendons were repaired by using a triple-looped suture technique in which the suture purchase length in each suture row was modified. Group 1, all lengths are 8-mm. Group 2, all lengths are 10-mm. Group 3, two are 10-mm and one is 8-mm. Group 4, one is 10-mm and two are 8-mm. The repaired tendons were subjected to load-to-failure test. The gap strength was significantly greater in Group 1 and Group 2 than in Group 3 and Group 4. This study demonstrates that maintaining equal core suture purchase lengths of each suture row increases the gap resistance.

Aortoiliac morphologic correlations in aneurysms undergoing endovascular repair.

PubMed

Ouriel, Kenneth; Tanquilut, Eugene; Greenberg, Roy K; Walker, Esteban

2003-08-01

The feasibility of endovascular aneurysm repair depends on morphologic characteristics of the aortoiliac segment. Knowledge of such characteristics is relevant to safe deployment of a particular device in a single patient and to development of new devices for use in patients with a broader spectrum of anatomic variations. We evaluated findings on computed tomography scans for 277 patients being considered for endovascular aneurysm repair. Aortic neck length and angulation estimates were generated with three-dimensional trigonometry. Specific centerline points were recorded, corresponding to the aorta at the celiac axis, lowest renal artery, cranial aspect of the aneurysm sac, aortic terminus, right hypogastric artery origin, and left hypogastric origin. Aortic neck thrombus and calcium content were recorded, and neck conicity was calculated in degrees. Statistical analysis was performed with the Spearman rank correlation. Data are expressed as median and interquartile range. Median diameter of the aneurysms was 52 mm (interquartile range, 48-59 mm) in minor axis and 56 mm (interquartile range, 51-64 mm) in major axis, and median length was 88 mm (interquartile range, 74-103 mm). Median proximal aortic neck diameter was 26 mm (interquartile range, 22-29 mm), and median neck length was 30 mm (interquartile range, 18-45 mm). The common iliac arteries were similar in diameter (right artery, 16 mm [interquartile range, 13-20 mm]; left artery, 15 mm [interquartile range, 11-18 mm]) and length (right, 59 mm [interquartile range, 50-69 mm]; left, 60 mm [interquartile range, 49-70 mm]). Median angulation of the infrarenal aortic neck was 40 degrees (interquartile range, 29-51 degrees), and median angulation of the suprarenal segment was 45 degrees (interquartile range, 36-57 degrees). By gender, sac diameter, proximal neck diameter, and iliac artery diameter were significantly larger in men. Significant linear associations were identified between sac diameter and sac length, neck angulation, and iliac artery diameter. As the length of the aneurysm sac increased the proximal aortic neck length decreased. Conversely, as the sac length decreased sac eccentricity increased. Mural thrombus content within the neck increased with increasing neck diameter. There is considerable variability in aortoiliac morphologic parameters. Significant associations were found between various morphologic variables, links that are presumably related to a shared pathogenesis for aberration in aortoiliac diameter, length, and angulation. Ultimately this information can be used to develop new endovascular devices with broader applicability and improved long-term results.

Growth disturbance after lengthening of the lower limb and quantitative assessment of physeal closure in skeletally immature patients with achondroplasia.

PubMed

Song, S H; Kim, S E; Agashe, M V; Lee, H; Refai, M A; Park, Y E; Choi, H J; Park, J H; Song, H R

2012-04-01

This study evaluated the effect of limb lengthening on longitudinal growth in patients with achondroplasia. Growth of the lower extremity was assessed retrospectively by serial radiographs in 35 skeletally immature patients with achondroplasia who underwent bilateral limb lengthening (Group 1), and in 12 skeletally immature patients with achondroplasia who did not (Group 2). In Group 1, 23 patients underwent only tibial lengthening (Group 1a) and 12 patients underwent tibial and femoral lengthening sequentially (Group 1b). The mean lengthening in the tibia was 9.2 cm (59.5%) in Group 1a, and 9.0 cm (58.2%) in the tibia and 10.2 cm (54.3%) in the femur in Group 1b. The mean follow-up was 9.3 years (8.6 to 10.3). The final mean total length of lower extremity in Group 1a was 526.6 mm (501.3 to 552.9) at the time of skeletal maturity and 610.1 mm (577.6 to 638.6) in Group 1b, compared with 457.0 mm (411.7 to 502.3) in Group 2. However, the mean actual length, representing the length solely grown from the physis without the length of distraction, showed that there was a significant disturbance of growth after limb lengthening. In Group 1a, a mean decrease of 22.4 mm (21.3 to 23.1) (4.9%) was observed in the actual limb length when compared with Group 2, and a greater mean decrease of 38.9 mm (37.2 to 40.8) (8.5%) was observed in Group 1b when compared with Group 2 at skeletal maturity. In Group 1, the mean actual limb length was 16.5 mm (15.8 to 17.2) (3.6%) shorter in Group 1b when compared with Group 1a at the time of skeletal maturity. Premature physeal closure was seen mostly in the proximal tibia and the distal femur with relative preservation of proximal femur and distal tibia. We suggest that significant disturbance of growth can occur after extensive limb lengthening in patients with achondroplasia, and therefore, this should be included in pre-operative counselling of these patients and their parents.

Stereological assessment of normal Persian squirrels (Sciurus anomalus) kidney.

PubMed

Akbari, Mohsen; Goodarzi, Nader; Tavafi, Majid

2017-03-01

The functions of the mammalian kidney are closely related to its structure. This suggests that renal function can be completely characterized by accurate knowledge of its quantitative morphological features. The aim of this study was to investigate the histomorphometric features of the kidney using design-based and unbiased stereological methods in the Persian squirrel (Sciurus anomalus), which is the only representative of the Sciuridae family in the Middle East. The left kidneys of five animals were examined. Total volume of the kidney, cortex, and medulla were determined to be 960.75 ± 87.4, 754.31 ± 77.09 and 206.1 ± 16.89 mm 3 , respectively. The glomerular number was 32844.03 ± 1069.19, and the total glomerular volume was estimated to be 36.7 ± 1.45 mm 3 . The volume and length of the proximal convoluted tubule were estimated at 585.67 ± 60.7 mm 3 and 328.8 ± 14.8 m, respectively, with both values being greater than those reported in the rat kidney. The volume and length of the distal convoluted tubule were calculated at 122.34 ± 7.38 mm 3 and 234.4 ± 17.45 m, respectively, which are also greater than those reported in the rat kidney. Despite the comparable body weight, the total number and mean individual volume of glomeruli in the Persian squirrel kidney were greater than those in the rat kidney. Overall, the stereological variables of the kidneys elucidated in this study are exclusive to the Persian squirrel. Our findings, together with future renal physiological data, will contribute to a better understanding of the renal structure-function relationship in the Persian squirrel.

Particle length of silages affects apparent ruminal synthesis of B vitamins in lactating dairy cows.

PubMed

Castagnino, D S; Kammes, K L; Allen, M S; Gervais, R; Chouinard, P Y; Girard, C L

2016-08-01

Effects of particle length of silages on apparent ruminal synthesis (ARS) and postruminal supply of B vitamins were evaluated in 2 feeding trials. Diets containing alfalfa (trial 1) or orchardgrass (trial 2) silages, chopped to either 19mm (long cut, LC) or 10mm (short cut, SC) theoretical particle length, as the sole forage were offered to ruminally and duodenally cannulated lactating Holstein cows in crossover design experiments. Forages chopped to a theoretical particle length of 19 and 10mm had mean particles sizes of 14.1 and 8.1mm, respectively, in trial 1, and 15.3 and 11.3mm, respectively, in trial 2. Trial 1 was conducted with 13 multiparous cows in two 19-d treatment periods; both diets contained approximately 20% forage neutral detergent fiber (NDF), 25% total NDF, and forage-to-concentrate ratios were approximately 47:53. Trial 2 was conducted with 15 cows in two 18-d treatment periods; both diets contained approximately 23% forage NDF, 28% total NDF, and had a forage-to-concentrate ratio of 50:50. Thiamine, riboflavin, niacin, vitamin B6, folates, and vitamin B12 were measured in feed and duodenal content. Daily ARS was calculated as the duodenal flow minus the intake. In trial 1, daily intake of individual B vitamins was increased with the LC diet, but ARS of thiamine, riboflavin, vitamin B6, and folates was reduced. In trial 2, except for folates, intakes of the other B vitamins were decreased with the LC diets, whereas ARS of riboflavin, niacin, and vitamin B6 was increased. Daily ARS of thiamine, riboflavin, niacin, and vitamin B6 were correlated negatively with their intake, suggesting that ruminal bacteria reduced their synthesis when dietary supply increased. Microbial activity could have also reduced degradation of thiamine, riboflavin, and niacin, which is supported by (1) the negative correlation between ARS of these vitamins and ruminal pH or microbial N duodenal flow; and (2) the positive correlation between ARS and ruminal concentrations of volatile fatty acids. Folate ARS followed the opposite correlation pattern. Nevertheless, in spite of differences in intake and ARS, with both forages, decreasing particle length of silages had limited effects on the amounts of B vitamins reaching the sites of absorption in the small intestine of dairy cows. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

1 Kw Arc-Jet Engine: Experiments With Argon

DTIC Science & Technology

2004-06-23

3 s- 6 ) R + R ( non-linear) FLAME STABILITY CHAMBER PRESSURE 1.0 - 1.625 atm VACUUM PRESSURE 30 – 30 mmHg FLAME LENGTH 28 – 33 mm CHAMBER...PRESSURE 2.25 – 2.875 atm VACUUM PRESSURE 30 – 40 mmHg FLAME LENGTH 36 – 42 mm CHAMBER PRESSURE 3.0 – 3.0 atm VACUUM PRESSURE 60 – 36 mmHg FLAME LENGTH 18

Conductive sub-layer of twisted-tape-induced swirl-flow heat transfer in vertical circular tubes with various twisted-tape inserts

NASA Astrophysics Data System (ADS)

Hata, K.; Fukuda, K.; Masuzaki, S.

2018-04-01

Twisted-tape-induced swirl-flow heat transfer due to exponentially increasing heat inputs with various exponential periods ( Q = Q 0 exp(t/τ), τ = 6.04 to 23.07 s) and twisted-tape-induced pressure drop was systematically measured for various mass velocities ( G = 4115 to 13,656 kg/m2 s), inlet liquid temperatures ( T in = 285.88 to 299.09 K), and inlet pressures ( P in = 847.45 to 943.29 kPa) using an experimental water loop flow. Measurements were made over a 59.2-mm effective length and three sections (upper, middle, and lower positions), within which four potential taps were spot-welded onto the outer surface of a 6-mm-inner-diameter, 69.6-mm-heated length, 0.4-mm-thickness platinum circular test tube. Type SUS304 twisted tapes with a width w = 5.6 mm, a thickness δ T = 0.6 mm, a total length l = 372 mm, and twist ratios y = 2.39 and 4.45 were employed in this study. The RANS equations (Reynolds Averaged Navier-Stokes Simulation) with a k-ɛ turbulence model for a circular tube 6 mm in diameter and 636 mm in length were numerically solved for heating of water with a heated section 6 mm in diameter and 70 mm in length using the CFD code, under the same conditions as the experimental ones and considering the temperature dependence of the thermo-physical properties concerned. The theoretical values of surface heat flux q on the circular tubes with twisted tapes with twist ratios y of 2.39 and 4.45 were found to be almost in agreement with the corresponding experimental values of heat flux q, with deviations of less than 30% for the range of temperature difference between the average heater inner surface temperature and the liquid bulk mean temperature ΔT L [ = T s,av - T L , T L = ( T in + T out )/2] considered in this study. The theoretical values of the local surface temperature T s , local average liquid temperature T f,av , and local liquid pressure drop ΔP x were found to be within almost 15% of the corresponding experimental ones. The thickness of the conductive sub-layer δ CSL and the nondimensional thickness of the conductive sub-layer y + CSL on the circular tubes with various twisted-tape inserts were determined on the basis of numerical solutions for the swirl velocities u sw ranging from 5.23 to 21.18 m/s. Correlations between the conductive sub-layer thickness δ CSL and the nondimensional thickness of the conductive sub-layer y + CSL for twisted-tape-induced swirl-flow heat transfer in a vertical circular tube were derived.

Design of polarized infrared athermal telephoto objective for penetrating the fog

NASA Astrophysics Data System (ADS)

Gao, Duorui; Fu, Qiang; Zhao, Zhao; Zhao, Bin; Zhong, Lijun; Zhan, Juntong

2014-11-01

Polarized infrared imaging technology is a new detection technique which own the ability of spying through the fog, highlighting the target and recognizing the forgeries, these characters make it a good advantage of increasing the work distance in the fog. Compared to the traditional infrared imaging method, polarized infrared imaging can identify the background and target easily, that is the most distinguishing feature of polarized infrared imaging technology. Owning to the large refractive index of the infrared material, temperature change will bring defocus seriously, athermal infrared objective is necessarily. On the other hand, athermal objective has large total length, and hard to be integrated for their huge volume. However telephoto objective has the character of small volume and short total length. The paper introduce a method of polarized and athermal infrared telephoto objective which can spy the fog. First assign the optical power of the fore group and the rear group on the basis of the principle of telephoto objective, the power of the fore group is positive and the rear group is negative; then distribute the optical power within each group to realize the ability of athermalization, finally computer-aided software is used to correct aberration. In order to prove the feasibility of the scheme, an athermal optical system was designed by virtue of ZEMAX software which works at 8~12 µm, the focal length of 150mm, F number is 2, and total length of the telephoto objective is 120mm. The environment temperature analysis shows that the optical system have stable imaging quality, MTF is close to diffraction limit. This telephoto objective is available for infrared polarized imaging.

Emergence, Development, and Maturity of the Gonad of Two Species of Chitons “Sea Cockroach” (Mollusca: Polyplacophora) through the Early Life Stages

PubMed Central

Avila-Poveda, Omar Hernando; Abadia-Chanona, Quetzalli Yasú

2013-01-01

This study describes and recognises, using histological and microscopical examinations on a morphometrical basis, several gonad traits through the early life stages of Chiton articulatus and C. albolineatus. Gonadal ontogenesis, gonad development stages, sexual differentiation, onset of the first sexual maturity, and growth sequences or “early life stages” were determined. In addition, allometry between lengths and body weight pooled for both sexes per each chiton were calculated using equation Y = aXb. A total of 125 chitons (4≤TL≤40 mm, in total length “TL”) were used. All allometric relations showed a strong positive correlation (r), close to 1, with b-values above three, indicating an isometric growth. Gonadal ontogenesis and gonad development stages were categorised into three periods (“Pw” without gonad, “Pe” gonad emergence, and “Pf” gonadal sac formed) and four stages (“S0” gametocytogenesis, “S1” gametogenesis, “S2” mature, and “S3” spawning), respectively. Compound digital images were attained for each process. Periods and stages are overlapped among them and between species, with the following overall confidence intervals in TL: Pw 6.13–14.32 mm, Pe 10.32–16.93 mm, Pf 12.99–25.01 mm, S0 16.08–24.34 mm (females) and 19.51–26.60 mm (males), S1 27.15–35.63 mm (females) and 23.45–32.27 mm (males), S2 24.48–40.24 mm (females) and 25.45–32.87 mm (males). Sexual differentiation (in S0) of both chitons occurs first as a female then as a male; although, males reach the onset of the first sexual maturity earlier than females, thus for C. articulatus males at 17 mm and females at 32 mm, and for C. albolineatus males at 23.5 mm and females at 28 mm, all in TL. Four early life stages (i.e., subjuvenile, juvenile, subadult, and adult) are described and proposed to distinguish growth sequences. Our results may be useful to diverse disciplines, from developmental biology to fisheries management. PMID:23936353

Refining the intraoperative measurement of the distal intrapancreatic part of a choledochal cyst during laparoscopic repair allows near total excision.

PubMed

Koga, Hiroyuki; Okawada, Manabu; Doi, Takashi; Miyano, Go; Lane, Geoffrey J; Yamataka, Atsuyuki

2015-10-01

During surgery for choledochal cyst (CC), any intrapancreatic CC (IPCC) must also be excised to prevent postoperative pancreatitis and stone formation. We report our technique for laparoscopic total IPCC excision (n = 16; mean age 6.0 years). We insert a fine ureteroscope with a light source into the opened CC through an extra 3.9-mm trocar placed in the epigastrium through a minute incision to identify the pancreatic duct orifice. By pulling the end of the ureteroscope emerging from the trocar gently to withdraw the tip from the pancreatic duct to where distal dissection was ceased under laparoscopic view, the IPCC can be measured. If longer than 5 mm, the distal CC is dissected further caudally until it is less than 5 mm. For accuracy, the distal CC is elevated with a suture that is exteriorized and clamped to provide constant traction. The IPCC was able to be measured in 11/16 (68 %). Initial lengths measured were 3-10 mm (5.2 ± 2.7 mm). Final IPCC were all 5 mm or less. Surgery was uncomplicated without any pancreatic duct injury and postoperative recovery was unremarkable. Follow-up MRI at 32 months showed no IPCC in any case. Measuring the IPCC enables total CC excision, thus reducing the potential for postoperative complications.

The effect of suspended sediment and color on ultraviolet spectrophotometric nitrate sensors

USGS Publications Warehouse

Snazelle, Teri T.

2016-03-08

Four commercially available ultraviolet nitrate spectrophotometric sensors were evaluated by the U.S. Geological Survey Hydrologic Instrumentation Facility (HIF) to determine the effects of suspended sediment concentration (SSC) and colored dissolved organic matter (CDOM) on sensor accuracy. The evaluated sensors were: the Hach NITRATAX plus sc (5-millimeters (mm) path length), Hach NITRATAX plus sc (2 mm), S::CAN Spectro::lyser (5 mm), and the Satlantic SUNA V2 (5 mm). A National Institute of Standards and Technology-traceable nitrate-free sediment standard was purchased and used to create the turbid environment, and an easily made filtered tea solution was used for the CDOM test. All four sensors performed well in the test that evaluated the effect of suspended sediment on accuracy. The Hach 5 mm, Hach 2 mm, and the SUNA V2 met their respective manufacturer accuracy specifications up to concentrations of 4,500 milligrams per liter (mg/L) SSC. The S::CAN failed to meet its accuracy specifications when the SSC concentrations exceeded 4,000 mg/L. Test results from the effect of CDOM on accuracy indicated a significant skewing of data from all four sensors and showed an artificial elevation of measured nitrate to varying amounts. Of the four sensors tested, the Satlantic SUNA V2’s accuracy was affected the least in the CDOM test. The nitrate concentration measured by the SUNA V2 was approximately 24 percent higher than the actual concentration when estimated total organic carbon values exceeded 44 mg/L. Measured nitrate concentration falsely increased 49 percent when measured by the Hach 5 mm, and 75 percent when measured by the Hach 2 mm. The S::CAN’s reported nitrate concentration increased 96 percent. Path length plays an important role in the sensor’s ability to compensate measurements for matrix interferences, but does not solely determine how well a sensor can handle all interferences. The sensor’s proprietary algorithms also play a key role in matrix interference compensation. The sensors’ ability to compensate for CDOM varied significantly during the tests, even among the three with 5-mm path lengths. Results of this evaluation suggest that the proprietary algorithms of the nitrate analyzers are more effective compensating for suspended sediment, and less effective compensating for CDOM (color) when sensor path length remains constant.

A new species of smooth skink (Squamata: Scincidae: Scincella) from Cambodia.

PubMed

Neang, Thy; Chan, Somaly; Poyarkov, Nikolay A

2018-05-18

Based on morphological and genetic evidence we evaluated the taxonomic status of a newly discovered forest-dwelling population of skink (genus Scincella) from the Keo Seima Wildlife Sanctuary, Mondulkiri Province, Cambodia. From phylogenetic analysis of a 668-bp fragment of the mtDNA COI and diagnostic morphological characters we allocate the newly discovered population to the Scincella reevesii-S. rufocaudata species complex and describe it as Scincella nigrofasciata sp. nov. The new skink species can be distinguished from all other Southeast Asian congeners by the following combination of morphological characters: snout-vent length (SVL) 40.0-52.6 mm; relative tail length (TaL/SVL ratio) 1.25-1.94; prefrontals in broad contact; infralabials 6; primary temporals 2; relative forelimb length (FIL/SVL ratio) 0.20-0.22; relative hindlimb length (HIL/SVL ratio) 0.30-0.33; relative forearm length (FoL/SVL ratio) 0.14-0.16; adpressed forelimbs and hind limbs either overlapping (0.4-2.2 mm) or separated (1.9-2.3 mm); midbody scale rows 32-33, paravertebral scales 69-74, vertebral scales 65-69; dorsal scales between dorsolateral stripes 8; comparatively slender fingers and toes, subdigital lamellae under fourth toe 15-17; dark discontinuous regular dorsal stripes 5-7; distinct black dorsolateral stripes, narrowing to lateral sides and extending to 52%-86% of total tail length. We provide additional information on the holotype of Scincella rufocaudata (Darevsky & Nguyen, 1983), and provide evidence for the species status of Scincella rupicola. Our discovery brings the number of Scincella species in Cambodia to five and emphasizes the incompleteness of knowledge on the herpetofaunal diversity of this country.

Fracture strength of different soldered and welded orthodontic joining configurations with and without filling material.

PubMed

Bock, Jens Johannes; Bailly, Jacqueline; Gernhardt, Christian Ralf; Fuhrmann, Robert Andreas Werner

2008-01-01

The aim of this study was to compare the mechanical strength of different joints made by conventional brazing, TIG and laser welding with and without filling material. Five standardized joining configurations of orthodontic wire in spring hard quality were used: round, cross, 3 mm length, 9 mm length and 7 mm to orthodontic band. The joints were made by five different methods: brazing, tungsten inert gas (TIG) and laser welding with and without filling material. For the original orthodontic wire and for each kind of joint configuration or connecting method 10 specimens were carefully produced, totalizing 240. The fracture strengths were measured with a universal testing machine (Zwick 005). Data were analyzed by ANOVA (p=0.05) and Bonferroni post hoc test (p=0.05). In all cases, brazing joints were ruptured on a low level of fracture strength (186-407 N). Significant differences between brazing and TIG or laser welding (p<0.05, Bonferroni post hoc test) were found in each joint configuration. The highest fracture strength means were observed for laser welding with filling material and 3 mm joint length (998 N). Using filling materials, there was a clear tendency to higher mean values of fracture strength in TIG and laser welding. However, statistically significant differences were found only in the 9-mm long joints (p<0.05, Bonferroni post hoc test). In conclusion, the fracture strength of welded joints was positively influenced by the additional use of filling material. TIG welding was comparable to laser welding except for the impossibility of joining orthodontic wire with orthodontic band.

FRACTURE STRENGTH OF DIFFERENT SOLDERED AND WELDED ORTHODONTIC JOINING CONFIGURATIONS WITH AND WITHOUT FILLING MATERIAL

PubMed Central

Bock, Jens Johannes; Bailly, Jacqueline; Gernhardt, Christian Ralf; Fuhrmann, Robert Andreas Werner

2008-01-01

The aim of this study was to compare the mechanical strength of different joints made by conventional brazing, TIG and laser welding with and without filling material. Five standardized joining configurations of orthodontic wire in spring hard quality were used: round, cross, 3 mm length, 9 mm length and 7 mm to orthodontic band. The joints were made by five different methods: brazing, tungsten inert gas (TIG) and laser welding with and without filling material. For the original orthodontic wire and for each kind of joint configuration or connecting method 10 specimens were carefully produced, totalizing 240. The fracture strengths were measured with a universal testing machine (Zwick 005). Data were analyzed by ANOVA (p=0.05) and Bonferroni post hoc test (p=0.05). In all cases, brazing joints were ruptured on a low level of fracture strength (186-407 N). Significant differences between brazing and TIG or laser welding (p<0.05, Bonferroni post hoc test) were found in each joint configuration. The highest fracture strength means were observed for laser welding with filling material and 3 mm joint length (998 N). Using filling materials, there was a clear tendency to higher mean values of fracture strength in TIG and laser welding. However, statistically significant differences were found only in the 9-mm long joints (p<0.05, Bonferroni post hoc test). In conclusion, the fracture strength of welded joints was positively influenced by the additional use of filling material. TIG welding was comparable to laser welding except for the impossibility of joining orthodontic wire with orthodontic band. PMID:19089229

Ultracompact, completely implantable permanent use electromechanical ventricular assist device and total artificial heart.

PubMed

Honda, N; Inamoto, T; Nogawa, M; Takatani, S

1999-03-01

An ultracompact, completely implantable permanent use electromechanical ventricular assist device (VAD) and total artificial heart (TAH) intended for 50-60 kg size patients have been developed. The TAH and VAD share a miniature electromechanical actuator that comprises a DC brushless motor and a planetary roller screw. The rotational force of the motor is converted into the rectilinear force of the roller screw to actuate the blood pump. The TAH is a one piece design with left and right pusher plate type blood pumps sandwiching an electromechanical actuator. The VAD is one half of the TAH with the same actuator but a different pump housing and a backplate. The blood contacting surfaces, including those of the flexing diaphragm and pump housing, of both the VAD and TAH were made of biocompatible polyurethane. The diameter, thickness, volume, and weight of the VAD are 90 mm, 56 mm, 285 cc, and 380 g, respectively, while those of the TAH are 90 mm, 73 mm, 400 cc, and 440 g, respectively. The design stroke volume of both the VAD and TAH is 60 cc with the stroke length being 12 mm. The stroke length and motor speed are controlled solely based on the commutation signals of the motor. An in vitro study revealed that a maximum pump flow of 7.5 L/min can be obtained with a pump rate of 140 bpm against a mean afterload of 100 mm Hg. The power requirement ranged from 4 to 6 W to deliver a 4-5 L/min flow against a 100 mm Hg afterload with the electrical-to-hydraulic efficiency being 19-20%. Our VAD and TAH are the smallest of the currently available devices and suitable for bridge to transplant application as well as for permanent circulatory support of 50-60 kg size patients.

76 FR 19748 - Atlantic Coastal Fisheries Cooperative Management Act Provisions; General Provisions for Domestic...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-08

... commercial fishing vessels from the following Federal American lobster regulations: (1) Gear specifications... Federally permitted vessels to utilize a combined total of 35 modified lobster traps to catch juvenile lobsters, (30-50 mm carapace length), throughout lobster management area 3 (Area 3), in an attempt to...

MERCURY CONCENTRATION IN FISH FROM STREAMS AND RIVERS THROUGHOUT THE WESTERN UNITED STATES

EPA Science Inventory

We collected and analyzed 2,707 large fish from 626 stream/river sites in 12 western U.S. states using a probability design to assess the regional distribution of whole fish mercury (Hg) concentrations. Large (>120 mm total length) fish Hg levels were strongly related to both fis...

Impact of minimum catch size on the population viability of Strombus gigas (Mesogastropoda: Strombidae) in Quintana Roo, Mexico.

PubMed

Peel, Joanne R; Mandujano, María del Carmen

2014-12-01

The queen conch Strombus gigas represents one of the most important fishery resources of the Caribbean but heavy fishing pressure has led to the depletion of stocks throughout the region, causing the inclusion of this species into CITES Appendix II and IUCN's Red-List. In Mexico, the queen conch is managed through a minimum fishing size of 200 mm shell length and a fishing quota which usually represents 50% of the adult biomass. The objectives of this study were to determine the intrinsic population growth rate of the queen conch population of Xel-Ha, Quintana Roo, Mexico, and to assess the effects of a regulated fishing impact, simulating the extraction of 50% adult biomass on the population density. We used three different minimum size criteria to demonstrate the effects of minimum catch size on the population density and discuss biological implications. Demographic data was obtained through capture-mark-recapture sampling, collecting all animals encountered during three hours, by three divers, at four different sampling sites of the Xel-Ha inlet. The conch population was sampled each month between 2005 and 2006, and bimonthly between 2006 and 2011, tagging a total of 8,292 animals. Shell length and lip thickness were determined for each individual. The average shell length for conch with formed lip in Xel-Ha was 209.39 ± 14.18 mm and the median 210 mm. Half of the sampled conch with lip ranged between 200 mm and 219 mm shell length. Assuming that the presence of the lip is an indicator for sexual maturity, it can be concluded that many animals may form their lip at greater shell lengths than 200 mm and ought to be considered immature. Estimation of relative adult abundance and densities varied greatly depending on the criteria employed for adult classification. When using a minimum fishing size of 200 mm shell length, between 26.2% and up to 54.8% of the population qualified as adults, which represented a simulated fishing impact of almost one third of the population. When conch extraction was simulated using a classification criteria based on lip thickness, it had a much smaller impact on the population density. We concluded that the best management strategy for S. gigas is a minimum fishing size based on a lip thickness, since it has lower impact on the population density, and given that selective fishing pressure based on size may lead to the appearance of small adult individuals with reduced fecundity. Furthermore, based on the reproductive biology and the results of the simulated fishing, we suggest a minimum lip thickness of ≥ 15 mm, which ensures the protection of reproductive stages, reduces the risk of overfishing, leading to non-viable density reduction.

Meteterakis saotomensis n. sp. (Nematoda: Heterakidae) from Schistometopum thomense (Bocage) (Gymnophiona: Dermophiidae) on São Tomé Island.

PubMed

Junker, Kerstin; Mariaux, Jean; Measey, G John; Mutafchiev, Yasen

2015-10-01

Meteterakis saotomensis n. sp. is described from Schistometopum thomense (Bocage), a gymnophionan endemic to the oceanic island of São Tomé in the Gulf of Guinea. The specimens were assigned to Meteterakis Karve, 1930, based on the possession of a head with three rounded lips, not set-off from the body, the absence of interlabia and cordons, females with a long vagina and males with a preanal sucker, surrounded by a cuticularised rim and caudal alae that are supported by fleshy papillae. The new species is characterised by: body length 4.2-4.5 mm (males) and 5.1-6.4 mm (females); total length of oesophagus, including pharyngeal portion and oesophageal bulb, 820-856 µm (males) and 898-1,070 µm (females); length of pharynx 57-58 µm (males) and 65-68 µm (females); spicules equal, 410-521 µm long, with tessellated ornamentation throughout their length and alae, and with bevelled tip; gubernaculum or 'gubernacular mass' absent; tail length 164-176 µm (males) and 214-239 µm (females), with elongated tip; vulva at 2.3-2.8 mm from anterior end, with anterior lip forming small flap. This is the second species of Meteterakis reported from gymnophionan hosts and the first from the Afrotropical region. Selected comparative morphological data for Meteterakis spp. are presented, and data on host range and geographic distribution are updated. The name M. striaturus Oshmarin & Demshin, 1972 is corrected to M. striatura to reflect the female gender of the genus name.

Flower, fruit phenology and flower traits in Cordia boissieri (Boraginaceae) from northeastern Mexico.

PubMed

Martínez-Adriano, Cristian Adrian; Jurado, Enrique; Flores, Joel; González-Rodríguez, Humberto; Cuéllar-Rodríguez, Gerardo

2016-01-01

We characterized variations in Cordia boissieri flowers and established if these variations occur between plants or between flowering events. Flowering and fruiting was measured for 256 plants. A GLM test was used to determine the relationship between flowering and fruit set processes and rainfall. We performed measurements of floral traits to detect variations within the population and between flowering events. The position of the anthers with respect to the ovary was determined in 1,500 flowers. Three out of four flowering events of >80% C. boissieri plants occurred after rainfall events. Only one flowering event occurred in a drought. Most plants flowered at least twice a year. The overlapping of flowering and fruiting only occurred after rainfall. Anthesis lasted three-to-five days, and there were two flower morphs. Half of the plants had longistylus and half had brevistylus flowers. Anacahuita flower in our study had 1-4 styles; 2-9 stamens; 6.5-41.5 mm long corolla; sepals from 4.5-29.5 mm in length; a total length from 15.5-59 mm; a corolla diameter from 10.5-77 mm. The nectar guide had a diameter from 5-30.5 mm; 4-9 lobes; and 5 distinguishable nectar guide colors. The highest variation of phenotypic expression was observed between plants.

Parasitism of Argulus japonicus in cultured and wild fish of Guangdong, China with new record of three hosts.

PubMed

Alsarakibi, Muhamd; Wadeh, Hicham; Li, Guoqing

2014-02-01

This study aimed to demonstrate the ability of Argulus japonicus to infect a wide range of freshwater fishes, as well as to understand the effects of fish origin and host body size on the incidence of A. japonicus. Samples of cultured and wild fish were collected randomly from July 2010 to March 2013, using angling, long-lining, gill-netting, and trapping from rivers and fish farms in Guangdong province, South China. Eight fish species were found to be heavily infected including the common carp, the goldfish, the black carp, the silver carp, the brown trout, the rainbow trout, the mandarin fish, and the perch. Furthermore, the black carp, the brown trout, and the mandarin fish were recorded as new hosts for the first time. During the present study, a total of 2,271 fishes were examined, out of which 712 fishes were found to be infected by a total of 1,443 A. japonicus. Abundance and intensity of A. japonicus infection were significantly influenced by origin of fishes (cultured and wild) and total length (class I, <250 mm; class II, 250-350 mm; and class III, >350 mm) of fish species, whereas varied impacts on prevalence of infection were observed. The correlation between total length of fishes and prevalence of A. japonicus infection was variable, where no significant correlation was observed in the black carp, the silver carp, the mandarin fish, and the perch. In spite of the weak negative correlation between body size of the silver carp and prevalence of infection, A. japonicus was the most abundant and intensive in the silver carp. Thus, aquaculturists should pay particular attention to the control of these fish lice due to its host biodiversity.

Thermal fatigue performance of integrally cast automotive turbine wheels

NASA Technical Reports Server (NTRS)

Humphreys, V. E.; Hofer, K. E.

1980-01-01

Fluidized bed thermal fatigue testing was conducted on 16 integrally cast automotive turbine wheels for 1000-10,000 (600 sec total) thermal cycles at 935/50 C. The 16 wheels consisted of 14 IN-792 + 1% Hf and 2 gatorized AF2-1DA wheels; 6 of the IN-792 + Hf wheels contained crack arrest pockets inside the blade root flange. Temperature transients during the thermal cycling were measured in three calibration tests using either 18 or 30 thermocouples per wheel. Thermal cracking based on crack length versus accumulated cycles was greatest for unpocketed wheels developing cracks in 8-13 cycles compared to 75-250 cycles for unpocketed wheels. However, pocketed wheels survived up to 10,000 cycles with crack lengths less than 20 mm, whereas two unpocketed wheels developed 45 mm long cracks in 1000-2000 cycles.

Canine and Premolar Root Dimensions in Chinese. A Reference for Osteoodontokeratoprosthesis Surgery.

PubMed

Sun, Stella Yue; Yeo, Woon Chee; Tay, Andrew Ban Guan; Tan, Donald Tiang Hwee; Tan, Danny Ben Poon

2018-01-01

Osteoodontokeratoprosthesis (OOKP) surgery is used to restore vision in end-stage corneal disorders, where an autogenous tooth supporting an optical cylinder is implanted through the cornea under a buccal mucosal graft. The ideal tooth for OOKP is a healthy single-rooted permanent tooth with sufficient buccolingual/palatal root diameter to accommodate an optical cylinder. The aim of this study was to determine the buccolingual/palatal diameters of canine and premolar roots in Chinese, for selection of teeth for OOKP surgery. This was an anatomical study on root dimensions of extracted intact teeth. Extracted canine and premolar teeth (excluding maxillary first premolars) were collected and the buccolingual/palatal and mesiodistal diameters of the root at the cervical line and at 2-mm intervals below the cervical line were measured with Vernier calipers. Other measurements included total tooth length, crown buccolingual/palatal diameter, and root length. Mean and minimum buccolingual/palatal root diameters were compiled for each 2-mm interval. A total of 415 extracted teeth (198 male, 217 female) were collected and measured. Recorded dimensions of keratoprostheses in 55 previous OOKP surgeries were used to establish acceptable lamina dimensions to ascertain root size adequacy. Premolars in Chinese female patients were undersized in a small minority. Minimal dimensions of teeth were insufficient if at 6 mm root level, the buccolingual/palatal width was less than 5 mm, or the mesiodistal width was less than 3 mm. This was noted in female mandibular first premolars (5.6%), maxillary second premolars (4.5%), and mandibular second premolars (1.5%). Canines have adequate dimensions for OOKP surgery. However, premolars in Chinese females may be undersized in a small minority. Copyright 2017 Asia-Pacific Academy of Ophthalmology.

[The length of the piston in otosclerosis surgery].

PubMed

Portmann, D; Alcantara, M; Vianna, M

2007-01-01

The measurement of the piston is always described as a significant stage of the surgery but its length is never clearly defined. The goal of this work is to determine the length of the prosthesis. From May 2003 to May 2005, 128 patients with otosclerosis, diagnosed on the basis of their clinical history and their audiogram, were included in this prospective study. Some of them were revision surgeries. The prosthesis generally used was the Portmann piston clip (Medtronic Xomed Inc Portmann Piston Clip Stainless Steel/Fluoroplastic). In stapedectomies, a Teflon piston of 0.6 mm of diameter was used (Pouret Company Fluoroplastic Stapes Prosthesis). These prostheses must be trimmed before their installation. The measurement technique is described. The length of the prosthesis was increased by 0.5 mm to include the thickness of the footplate. The Portmann piston clip was used 116 times (100 initial surgeries and 16 revisions surgeries) and the Teflon prosthesis of 0.6 mm of diameter only 13 times (6 primary stapedectomies and 7 revisions stapedectomies). The length of the prosthesis was between 3,5 mm and 5 mm. In the majority of cases, the length of the prosthesis was 4.75 mm (62 patients, 48.1%), followed by 4.5 mm (29 patients, 22.5%) and 5 mm (27 patients, 20.9%). In eleven cases (8.5%) the prosthesis measured less than 4,5 mm. None of the patients in this study experienced a postoperative sensorineural hearing loss. The measurement of the length of the piston is very significant, and in our study the majority of the pistons were cut at 4.75 mm which indicates an incus-footplate measurement of 4.25 mm.

Variation in Size and Form between Left and Right Maxillary Central Incisor Teeth.

PubMed

Vadavadagi, Suneel V; Hombesh, M N; Choudhury, Gopal Krishna; Deshpande, Sumith; Anusha, C V; Murthy, D Kiran

2015-02-01

To compare the variation in size of left and right maxillary central incisors for male patients (using digital calipers of 0.01 mm accuracy). To compare the variation in size of left and right maxillary central incisors for female patients (using digital calipers of 0.01 mm accuracy). To find out the difference between the maxillary central incisors of men and women. Its clinical applicability if difference exists. A total of 70 dental students of PMNM Dental College and Hospital were selected. Of 70 dental students, 40 male and 30 female were selected. Impressions were made for all subjects, using irreversible hydrocolloid (Algitex, manufacturer DPI, Batch-T-8804) using perforated stock metal trays. The mesiodistal crown width and cervical width were measured for each incisor and recorded separately for left and right teeth. The length was measured for each incisor and recorded separately for left and right maxillary central incisor using digitec height caliper. The mean value of maximum crown length of maxillary left central incisor of male was greater in length compared with maxillary right central incisor. Mean value of maximum crown length for male patient right and left side was greater compared with maximum crown length of female patient. When compared the dimensions of teeth between two sex, male group shows larger values to female group.

A lazy way to design infrared lens

NASA Astrophysics Data System (ADS)

Qiu, RongSheng; Wu, JianDong; Chen, LongJiang; Yu, Kun; Pang, HaoJun; Hu, BaiZhen

2017-08-01

We designed a compact middle-wave infrared (MWIR) lens with a large focal length ratio (about 1.5:1), used in the 3.7 to 4.8 μm range. The lens is consisted of a compact front group and a re-imaging group. Thanks to the compact front group configuration, it is possible to install a filter wheel mechanism in such a tight space. The total track length of the lens is about 50mm, which includes a 2mm thick protective window and a cold shield of 12mm. The full field of view of the lens is about 3.6°, and F number is less than 1.6, the image circle is about 4.6mm in diameter. The design performance of the lens reaches diffraction limitation, and doesn't change a lot during a temperature range of -40°C +60°C. This essay proposed a stepwise design method of infrared optical system guided by the qualitative approach. The method fully utilize the powerful global optimization ability, with a little effort to write code snippet in optical design software, frees optical engineer from tedious calculation of the original structure.

Age, growth, and natural mortality of schoolmaster (Lutjanus apodus) from the southeastern United States.

PubMed

Potts, Jennifer C; Burton, Michael L; Myers, Amanda R

2016-01-01

Ages of schoolmaster ( n = 136) from the southeastern Florida coast from 1981-2015 were determined using sectioned sagittal otoliths. Opaque zones were annular, forming March-July (peaking in May-June). Schoolmaster ranged in age from 1-42 years; the largest fish measured 505 mm total length (TL) and was 19 years old. The oldest fish measured 440 mm TL. Estimated body size relationships for schoolmaster were: W = 9.26 × 10 -6 TL 3.11 ( n = 256, r 2 = 0.95); W = 2.13 × 10 -5 FL 2.99 ( n = 161, r 2 = 0.95); TL = 1.03 FL + 10.36 ( n = 143, r 2 = 0.99); and FL = 0.96 TL - 8.41 ( n = 143, r 2 = 0.99), where W = whole weight in g, FL = fork length in mm, and TL in mm. The fitted von Bertalanffy growth equation was: L t = 482 (1 - e -0.12( t +2.79) ) ( n = 136). Based on published life history relationships, a point estimate of natural mortality for schoolmaster was M = 0.10, while age-specific estimates of M ranged from 1.57-0.18 for ages 1-42.

Cabling design of booster and storage ring construction progress of TPS

NASA Astrophysics Data System (ADS)

Wong, Y.-S.; Liu, K.-B.; Liu, C.-Y.; Wang, b.-S.

2017-06-01

The 2012 Taiwan Photon Source (TPS) cable construction project started after 10 months to complete the cable laying and installation of power supply. The circumference of the booster ring (BR) is 496.8 m, whereas that of the storage ring (SR) is 518.4 m. Beam current is set to 500 mA at 3.3 GeV. The paper on grounding systems discusses the design of the ground wire (< 0.2 Ω) with low impedance, power supply of the accelerator and cabling tray. The flow and size of the ground current are carefully evaluated to avoid grounded current from flowing everywhere, which causes interference problems. In the design of the TPS, special shielding will be established to isolate the effects of electromagnetic interference on the magnet and ground current. Booster ring dipoles are connected by a series of 54-magnet bending dipole; the cable size of its stranded wire measures 250 mm2, with a total length of 5000 m. Booster ring and storage ring quadrupoles have 150 magnets; the cable size of their stranded wire is 250 mm2, with a total length of 17000 m. Storage ring dipole consists of 48 magnets; the cable size of its stranded wire is 325 mm2, with a total length of 6000 m. This study discusses the power supply cabling design of the storage ring and booster ring construction progress of TPS. The sections of this paper are divided into discussions of the construction of the control and instrument area, cabling layout of booster ring and storage ring, as well as the installation and commission machine. This study also discusses the use of a high-impedance meter to determine the effect of cabling insulation and TPS power supply machine on energy transfer to ensure the use of safe and correct magnet.

Impact of new society of radiologists in ultrasound early first-trimester diagnostic criteria for nonviable pregnancy.

PubMed

Hu, Maowen; Poder, Liina; Filly, Roy A

2014-09-01

New early first-trimester diagnostic criteria for nonviable pregnancy recommended by the Society of Radiologists in Ultrasound via a multispecialty consensus panel extended the diagnostic size criteria of crown-rump length from 5 to 7 mm for embryos without a heartbeat and mean sac diameter from 16 to 25 mm for "empty" sacs. Our study assessed the potential impact of the new criteria on the number of additional follow-up sonograms these changes would engender. A retrospective study of all first-trimester sonograms in women with first trimester bleeding from 1999 to 2008 was conducted. Everyone included in the study had a visible gestational sac in the uterus. There were no pregnancies of unknown location or ectopic pregnancies included in this study cohort. Pregnancy of unknown location was used to describe cases in which there were no signs of pregnancy inside or outside the uterus on transvaginal sonography despite a positive pregnancy test result. A total of 1013 patients met the inclusion criteria. Seven hundred fifty-two patients (74%) had identifiable embryos, and 261 (26%) did not. Of those with an identifiable embryo, 286 (38%) had no detectable embryonic cardiac activity. The breakdown of crown-rump lengths in this group was as follows: 100 measuring less than 5 mm, 36 measuring 5 to 7 mm, and 150 measuring 7 mm or greater. The breakdown of mean sac diameters in those without a visible embryo was as follows: 120 measuring less than 16 mm, 90 measuring 16 to 25 mm, and 51 measuring 25 mm or greater. When diagnosing a failed pregnancy, there can be no room for error. Only 126 of 1013 early pregnancies threatening to abort (12%) fell into the more conservative zones defined by the new compared to the former size criteria (crown-rump length, 5-7 mm; mean sac diameter, 16-25 mm). Therefore, the potential impact of the new guidelines on follow-up sonograms does not appear inordinate. © 2014 by the American Institute of Ultrasound in Medicine.

Radiographic cup position following posterior and lateral approach to total hip arthroplasty. An explorative randomized controlled trial.

PubMed

Kruse, Christine; Rosenlund, Signe; Broeng, Leif; Overgaard, Søren

2018-01-01

The two most common surgical approaches to total hip arthroplasty are the posterior approach and lateral approach. The surgical approach may influence cup positioning and restoration of the offset, which may affect the biomechanical properties of the hip joint. The primary aim was to compare cup position between posterior approach and lateral approach. Secondary aims were to compare femoral offset, abductor moment arm and leg length discrepancy between the two approaches. Eighty patients with primary hip osteoarthritis were included in a randomized controlled trial and assigned to total hip arthroplasty using posterior approach or lateral approach. Postoperative radiographs from 38 patients in each group were included in this study for measurement of cup anteversion and inclination. Femoral offset, cup offset, total offset, abductor moment arm and leg length discrepancy were measured on preoperative and postoperative radiographs in 28 patients in each group. We found that mean anteversion was 5° larger in the posterior approach group (95% CI, -8.1 to -1.4; p = 0.006), while mean inclination was 5° less steep (95% CI, 2.7 to 7.2; p<0.001) compared with the lateral approach group. The posterior approach group had a larger mean femoral offset of 4.3mm (95% CI, -7.4 to -1.3, p = 0.006), mean total offset of 6.3mm (95% CI, -9.6 to -3; p<0.001) and mean abductor moment arm of 4.8mm (95% CI, -7.6 to -1.9; p = 0.001) compared with the lateral approach group. We found a larger cup anteversion but less steep cup inclination in the posterior approach group compared with the lateral approach group. Femoral offset and abductor moment arm were restored after total hip arthroplasty using lateral approach but significantly increased when using posterior approach.

Axial length growth and the risk of developing myopia in European children.

PubMed

Tideman, Jan Willem Lodewijk; Polling, Jan Roelof; Vingerling, Johannes R; Jaddoe, Vincent W V; Williams, Cathy; Guggenheim, Jeremy A; Klaver, Caroline C W

2018-05-01

To generate percentile curves of axial length (AL) for European children, which can be used to estimate the risk of myopia in adulthood. A total of 12 386 participants from the population-based studies Generation R (Dutch children measured at both 6 and 9 years of age; N = 6934), the Avon Longitudinal Study of Parents and Children (ALSPAC) (British children 15 years of age; N = 2495) and the Rotterdam Study III (RS-III) (Dutch adults 57 years of age; N = 2957) contributed to this study. Axial length (AL) and corneal curvature data were available for all participants; objective cycloplegic refractive error was available only for the Dutch participants. We calculated a percentile score for each Dutch child at 6 and 9 years of age. Mean (SD) AL was 22.36 (0.75) mm at 6 years, 23.10 (0.84) mm at 9 years, 23.41 (0.86) mm at 15 years and 23.67 (1.26) at adulthood. Axial length (AL) differences after the age of 15 occurred only in the upper 50%, with the highest difference within the 95th percentile and above. A total of 354 children showed accelerated axial growth and increased by more than 10 percentiles from age 6 to 9 years; 162 of these children (45.8%) were myopic at 9 years of age, compared to 4.8% (85/1781) for the children whose AL did not increase by more than 10 percentiles. This study provides normative values for AL that can be used to monitor eye growth in European children. These results can help clinicians detect excessive eye growth at an early age, thereby facilitating decision-making with respect to interventions for preventing and/or controlling myopia. © 2017 The Authors. Acta Ophthalmologica published by John Wiley & Sons Ltd on behalf of Acta Ophthalmologica Scandinavica Foundation.

The influence of uncemented femoral stem length and design on its primary stability: a finite element analysis.

PubMed

Reimeringer, M; Nuño, N; Desmarais-Trépanier, C; Lavigne, M; Vendittoli, P A

2013-01-01

One of the crucial factors for short- and long-term clinical success of total hip arthroplasty cementless implants is primary stability. Indeed, motion at the bone-implant interface above 40 μm leads to partial bone ingrowth, while motion exceeding 150 μm completely inhibits bone ingrowth. The aim of this study was to investigate the effect of two cementless femoral stem designs with different lengths on the primary stability. A finite element model of a composite Sawbones(®) fourth generation, implanted with five lengths of the straight prosthesis design and four lengths of the curved prosthesis design, was loaded with hip joint and abductor forces representing two physiological activities: fast walking and stair climbing. We found that reducing the straight stem length from 146 to 54 mm increased the average micromotion from 17 to 52 μm during fast walking, while the peak value increased from 42 to 104 μm. With the curved stem, reducing length from 105 to 54 mm increased the average micromotion from 10 to 29 μm, while the peak value increased from 37 to 101 μm. Similar findings are obtained for stair climbing for both stems. Although the present study showed that femoral stem length as well as stem design directly influences its primary stability, for the two femoral stems tested, length could be reduced substantially without compromising the primary stability. With the aim of minimising surgical invasiveness, newer femoral stem design and currently well performing stems might be used with a reduced length without compromising primary stability and hence, long-term survivorship.

Ex vivo accuracy of an apex locator using digital signal processing in primary teeth.

PubMed

Leonardo, Mário Roberto; da Silva, Lea Assed Bezerra; Nelson-Filho, Paulo; da Silva, Raquel Assed Bezerra; Lucisano, Marília Pacífico

2009-01-01

The purpose of this study was to evaluate ex vivo the accuracy an electronic apex locator during root canal length determination in primary molars. One calibrated examiner determined the root canal length in 15 primary molars (total=34 root canals) with different stages of root resorption. Root canal length was measured both visually with the placement of a K-file 1 mm short of the apical foramen or the apical resorption bevel, and electronically using an electronic apex locator (Digital Signal Processing). Data were analyzed statistically using the intraclass correlation (ICC) test. Comparing the actual and electronic root canal length measurements in the primary teeth showed a high correlation (ICC=0.95). The Digital Signal Processing apex locator is useful and accurate for apex foramen location during root canal length measurement in primary molars.

Integration of a nonmetallic electrostatic precipitator and a wet scrubber for improved removal of particles and corrosive gas cleaning in semiconductor manufacturing industries.

PubMed

Kim, Hak-Joon; Han, Bangwoo; Kim, Yong-Jin; Yoa, Seok-Jun; Oda, Tetsuji

2012-08-01

To remove particles in corrosive gases generated by semiconductor industries, we have developed a novel non-metallic, two-stage electrostatic precipitator (ESP). Carbon brush electrodes and grounded carbon fiber-reinforced polymer (CFRP) form the ionization stage, and polyvinyl chloride collection plates are used in the collection stage of the ESP The collection performance of the ESP downstream of a wet scrubber was evaluated with KC1, silica, and mist particles (0.01-10 pm), changing design and operation parameters such as the ESP length, voltage, and flow rate. A long-term and regeneration performance (12-hr) test was conducted at the maximum operation conditions of the scrubber and ESP and the performance was then demonstrated for 1 month with exhaust gases from wet scrubbers at the rooftop of a semiconductor manufacturing plant in Korea. The results showed that the electrical and collection performance of the ESP (16 channels, 400x400 mm2) was maintained with different grounded plate materials (stainless steel and CFRP) and different lengths of the ionization stage. The collection efficiency of the ESP at high air velocity was enhanced with increases in applied voltages and collection plate lengths. The ESP (16 channels with 100 mm length, 400x400 mm2x540 mm with a 10-mm gap) removed more than 90% of silica and mistparticles with 10 and 12 kV applied to the ESPat the air velocity of 2 m/s and liquid-to-gas ratio of 3.6 L/m3. Decreased performance after 13 hours ofcontinuous operation was recovered to the initial performance level by 5 min of water washing. Moreover during the 1-month operation at the demonstration site, the ESP showed average collection efficiencies of 97% based on particle number and 92% based on total particle mass, which were achieved with a much smaller specific corona power of 0.28 W/m3/hr compared with conventional ESPs.

Fatigue during maximal sprint cycling: unique role of cumulative contraction cycles.

PubMed

Tomas, Aleksandar; Ross, Emma Z; Martin, James C

2010-07-01

Maximal cycling power has been reported to decrease more rapidly when performed with increased pedaling rates. Increasing pedaling rate imposes two constraints on the neuromuscular system: 1) decreased time for muscle excitation and relaxation and 2) increased muscle shortening velocity. Using two crank lengths allows the effects of time and shortening velocity to be evaluated separately. We conducted this investigation to determine whether the time available for excitation and relaxation or the muscle shortening velocity was mainly responsible for the increased rate of fatigue previously observed with increased pedaling rates and to evaluate the influence of other possible fatiguing constraints. Seven trained cyclists performed 30-s maximal isokinetic cycling trials using two crank lengths: 120 and 220 mm. Pedaling rate was optimized for maximum power for each crank length: 135 rpm for the 120-mm cranks (1.7 m x s(-1) pedal speed) and 109 rpm for the 220-mm cranks (2.5 m x s(-1) pedal speed). Power was recorded with an SRM power meter. Crank length did not affect peak power: 999 +/- 276 W for the 120-mm crank versus 1001 +/- 289 W for the 220-mm crank. Fatigue index was greater (58.6% +/- 3.7% vs 52.4% +/- 4.8%, P < 0.01), and total work was less (20.0 +/- 1.8 vs 21.4 +/- 2.0 kJ, P < 0.01) with the higher pedaling rate-shorter crank condition. Regression analyses indicated that the power for the two conditions was most highly related to cumulative work (r2 = 0.94) and to cumulative cycles (r2 = 0.99). These results support previous findings and confirm that pedaling rate, rather than pedal speed, was the main factor influencing fatigue. Our novel result was that power decreased by a similar increment with each crank revolution for the two conditions, indicating that each maximal muscular contraction induced a similar amount of fatigue.

Imaging of patent foramen ovale with 64-section multidetector CT.

PubMed

Saremi, Farhood; Channual, Stephanie; Raney, Aidan; Gurudevan, Swaminatha V; Narula, Jagat; Fowler, Steven; Abolhoda, Amir; Milliken, Jeffrey C

2008-11-01

To investigate the feasibility of 64-section multidetector computed tomography (CT) by using CT angiography (a) to demonstrate anatomic detail of the interatrial septum pertinent to the patent foramen ovale (PFO), and (b) to visually detect left-to-right PFO shunts and compare these findings in patients who also underwent transesophageal echocardiography (TEE). In this institutional review board-approved HIPAA-compliant study, electrocardiographically gated coronary CT angiograms in 264 patients (159 men, 105 women; mean age, 60 years) were reviewed for PFO morphologic features. The length and diameter of the opening of the PFO tunnel, presence of atrial septal aneurysm (ASA), and PFO shunts were evaluated. A left-to-right shunt was assigned a grade according to length of contrast agent jet (grade 1, 1 cm to 2 cm; grade 3, >2 cm). In addition, 23 patients who underwent both modalities were compared (Student t test and linear regression analysis). A difference with P < .05 was significant. A flap valve, seen in 101 (38.3%) patients, was patent at the entry into the right atrium (PFO) in 62 patients (61.4% of patients with flap valve, 23.5% of total patients). A left-to-right shunt was detected in 44 (16.7% of total) patients (grade 1, 61.4%; grade 2, 34.1%; grade 3, 4.5%). No shunt was seen in patients without a flap valve. Mean length of PFO tunnel was 7.1 mm in 44 patients with a shunt and 12.1 mm in 57 patients with a flap valve without a shunt (P < .0001). In patients with a tunnel length of 6 mm or shorter, 92.6% of the shunts were seen. ASA was seen in 11 (4.2%) patients; of these patients, a shunt was seen in seven (63.6%). In 23 patients who underwent CT angiography and TEE, both modalities showed a PFO shunt in seven. Multidetector CT provides detailed anatomic information about size, morphologic features, and shunt grade of the PFO. Shorter tunnel length and septal aneurysms are frequently associated with left-to-right shunts in patients with PFO. (c) RSNA, 2008.

Investigation of side wall effects on an inward scramjet inlet at Mach number 8.6

NASA Astrophysics Data System (ADS)

Rolim, Tiago Cavalcanti

Experimental and computational studies were conducted to evaluate the performance of a scramjet inlet as the side cowl length is changed. A slender inward turning inlet of a total length of 304.8 mm, a span of 50.8 mm with the compression at 11.54 deg and CR = 4.79 was used. The side cowl lengths were of 0, 50.8 and 76.2 mm. The UTA Hypersonic Shock Tunnel facility was used in the reflected mode. The model was instrumented with nine piezoelectric pressure transducers, for static and total pressure measurements. A wedge was mounted at the rear of the inlet in order to accommodate a Pitot pressure rake. The driven tube was instrumented with three pressure transducers. Two of them were used to measure the incident shock wave speed, and a third one was used for stagnation pressure measurements during a test. Furthermore, a Pitot probe was installed below the model in order to measure the impact pressure on each run, this reading along with the driven sensor readings, allowed us for the calculation of freestream properties. During the experiments, nominal stagnation enthalpy of 0.67 MJ/kg and stagnation pressure of 3.67 MPa were achieved. Freestream conditions were Mach number 8.6 and Reynolds number of 1.94 million per m. Test times were 300 - 500 microseconds. Numerical simulations using RANS with the Wilcox K-w turbulence model were performed using ANSYS Fluent. The results from the static pressure measurements presented a good agreement with CFD predictions. Moreover, the uniformity at the inlet exit was achieved within the experimental precision. The experiments showed that the cowl length has a pronounced effect in the pressure distribution on the inlet and a minor effect in the exit flow Mach number. The numerical results confirmed these trends and showed that a complex flow structure is formed in the cowl-ramp corners; a non-uniform transverse shock structure was found to be related to the cowl leading edge position. Cross flow due to the side expansion increases the flow angularity as the cowl length decreases.

Comparative techniques of medial rectus muscle retraction for endoscopic exposure of the medial intraconal space.

PubMed

Lin, Giant C; Freitag, Suzanne K; Kocharyan, Armine; Yoon, Michael K; Lefebvre, Daniel R; Bleier, Benjamin S

2016-05-01

The medial rectus muscle (MRM) is the medial boundary to the intraconal space of the orbit, and retraction of the MRM is oftentimes necessary for endoscopic removal of intraconal tumors, e.g., orbital hemangioma. We evaluated each of the reported methods of MRM retraction for endoscopic orbital surgery and quantified the degree of intraconal exposure conferred by each method. Eight orbits from four cadaver heads were dissected. In each orbit, medial orbital decompression was performed and the MRM was retracted by using four previously described techniques: (1) external MRM retraction at the globe insertion point by using vessel loop (external group), (2) transseptal MRM retraction by using vessel loop (transseptal group), (3) transchoanal retraction of the MRM by using vessel loop (choanal group), and (4) transseptal four-handed technique by using double ball retraction by a second surgeon (transseptal double ball group). The length, height, and area of exposure of the medial intraconal space were quantified and compared. The average ± standard deviation (SD) anterior-posterior exposures for the external group, transseptal group, and transseptal double ball group were 17.51 ± 3.39 mm, 16.59 ± 4.16 mm, and 18.0 ± 15.25 mm, respectively. The choanal group provided significantly less exposure (12.39 ± 3.44 mm, p = 0.049) than the other groups. The average ± SD vertical exposures for the transseptal group, choanal group, and transseptal double ball group were 12.53 ± 4.38 mm, 13.05 ± 5.86 mm, and 13.57 ± 3.74 mm, respectively. The external group provided significantly less exposure (4.51 ± 1.56 mm, p = 0.0072) than the other groups. The transseptal and transseptal double ball groups provided the greatest total access by surface area (58.88 ± 26.96 mm(2) and 62.94 ± 34.74 mm(2), respectively) compared with the external and choanal groups (34.82 ± 23.37 mm(2) and 43.10 ± 23.68 mm(2), respectively). Although the transseptal trajectory of MRM retraction was optimal, the difference in total area of exposure between the static vessel loop retraction and the dynamic, four-handed technique with double ball instrument retraction was not significant. Of note, the exposure provided by the choanal technique required the surgeon to work both above and below the muscle. Retraction of the MRM toward the choanae provided the least length of exposure, and external retraction exposed the least height and total area. Transseptal MRM retraction was most favorable and provided the largest endoscopic corridor to the medial intraconal space. A four-handed approach for endoscopic intraconal surgery of the orbit may offer advantages in dynamic adjustments in retraction.

Go big or … don't? A field-based diet evaluation of freshwater piscivore and prey fish size relationships

PubMed Central

Ahrenstorff, Tyler D.; Diana, James S.; Fetzer, William W.; Jones, Thomas S.; Lawson, Zach J.; McInerny, Michael C.; Santucci, Victor J.; Vander Zanden, M. Jake

2018-01-01

Body size governs predator-prey interactions, which in turn structure populations, communities, and food webs. Understanding predator-prey size relationships is valuable from a theoretical perspective, in basic research, and for management applications. However, predator-prey size data are limited and costly to acquire. We quantified predator-prey total length and mass relationships for several freshwater piscivorous taxa: crappie (Pomoxis spp.), largemouth bass (Micropterus salmoides), muskellunge (Esox masquinongy), northern pike (Esox lucius), rock bass (Ambloplites rupestris), smallmouth bass (Micropterus dolomieu), and walleye (Sander vitreus). The range of prey total lengths increased with predator total length. The median and maximum ingested prey total length varied with predator taxon and length, but generally ranged from 10–20% and 32–46% of predator total length, respectively. Predators tended to consume larger fusiform prey than laterally compressed prey. With the exception of large muskellunge, predators most commonly consumed prey between 16 and 73 mm. A sensitivity analysis indicated estimates can be very accurate at sample sizes greater than 1,000 diet items and fairly accurate at sample sizes greater than 100. However, sample sizes less than 50 should be evaluated with caution. Furthermore, median log10 predator-prey body mass ratios ranged from 1.9–2.5, nearly 50% lower than values previously reported for freshwater fishes. Managers, researchers, and modelers could use our findings as a tool for numerous predator-prey evaluations from stocking size optimization to individual-based bioenergetics analyses identifying prey size structure. To this end, we have developed a web-based user interface to maximize the utility of our models that can be found at www.LakeEcologyLab.org/pred_prey. PMID:29543856

Microvascular distribution in the ocular conjunctiva and digestive tract in an experimental setting.

PubMed

Pranskūnas, Andrius; Pilvinis, Vidas; Dambrauskas, Žilvinas; Rasimavičiūtė, Renata; Milieškaitė, Eglė; Bubulis, Algimantas; Veikutis, Vincentas; Vaitkaitis, Dinas; Boerma, E Christiaan

2012-01-01

Recently improved microcirculatory imaging techniques, such as orthogonal polarization spectral (OPS) and its technical successor sidestream dark field (SDF) imaging, in handheld devices have allowed a direct observation of the microcirculation at the bedside. Usually a cut-off of 20 µm in diameter is used to differentiate small vessels (mainly capillaries) from large vessels (mainly venules) during this technique. We hypothesized that it was possible to measure the small vessels with a considerably smaller inner diameter. Images of the sublingual, conjunctival, jejunal, and rectal mucosa microcirculation were obtained with SDF videomicroscopy (Microscan®, Microvision Medical, Amsterdam, the Netherlands). Using the validated software, the length and diameter of microvessels were manually traced with a computer-generated line. All vessels were divided into the groups according to the inner diameter. A total of 156 SDF images of the sublingual, ocular conjunctival, jejunal, and rectal mucosa were taken in 13 pigs. The length of microscopic vessels progressively increased with a decrease in the vessel diameter less than 8 mm in all the lodges, such as sublingual (80.6% of total vessel length), ocular conjunctival (76.5% of total vessel length), jejunal (99.8% of total vessel length), and rectal (97.8% of total vessel length), due to capillary network formation. There was no significant difference in the distribution of vessels from 0 to 10 µm in diameter comparing sublingual and eye conjunctival as well as jejunal and rectal mucosa. In pigs, small-diameter microscopic vessels (<10 µm) dominated in all the studied lodges (sublingual, ocular conjunctival, jejunal, and rectal mucosa), and this is evidence to establish a new cut-off for capillaries in microcirculatory analysis of SDF imaging in experimental and clinical studies.

Go big or … don't? A field-based diet evaluation of freshwater piscivore and prey fish size relationships.

PubMed

Gaeta, Jereme W; Ahrenstorff, Tyler D; Diana, James S; Fetzer, William W; Jones, Thomas S; Lawson, Zach J; McInerny, Michael C; Santucci, Victor J; Vander Zanden, M Jake

2018-01-01

Body size governs predator-prey interactions, which in turn structure populations, communities, and food webs. Understanding predator-prey size relationships is valuable from a theoretical perspective, in basic research, and for management applications. However, predator-prey size data are limited and costly to acquire. We quantified predator-prey total length and mass relationships for several freshwater piscivorous taxa: crappie (Pomoxis spp.), largemouth bass (Micropterus salmoides), muskellunge (Esox masquinongy), northern pike (Esox lucius), rock bass (Ambloplites rupestris), smallmouth bass (Micropterus dolomieu), and walleye (Sander vitreus). The range of prey total lengths increased with predator total length. The median and maximum ingested prey total length varied with predator taxon and length, but generally ranged from 10-20% and 32-46% of predator total length, respectively. Predators tended to consume larger fusiform prey than laterally compressed prey. With the exception of large muskellunge, predators most commonly consumed prey between 16 and 73 mm. A sensitivity analysis indicated estimates can be very accurate at sample sizes greater than 1,000 diet items and fairly accurate at sample sizes greater than 100. However, sample sizes less than 50 should be evaluated with caution. Furthermore, median log10 predator-prey body mass ratios ranged from 1.9-2.5, nearly 50% lower than values previously reported for freshwater fishes. Managers, researchers, and modelers could use our findings as a tool for numerous predator-prey evaluations from stocking size optimization to individual-based bioenergetics analyses identifying prey size structure. To this end, we have developed a web-based user interface to maximize the utility of our models that can be found at www.LakeEcologyLab.org/pred_prey.

Influence of fiber length on flexural and impact properties of Zalacca Midrib fiber/HDPE by compression molding

NASA Astrophysics Data System (ADS)

Pamungkas, Agil Fitri; Ariawan, Dody; Surojo, Eko; Triyono, Joko

2018-02-01

The aim of the research is to investigate the effect of fiber length on the flexural and impact properties of the composite of Zalacca Midrib Fiber (ZMF)/HDPE. The process of making composite was using compression molding method. The variation of fiber length were 1 mm, 3 mm, 5 mm, 7 mm and 9 mm, at 30% fiber volume fraction. The flexural and impact test according to ASTM D790 and ASTM D5941, respectively. Observing fracture surface was examained by using Scanning Electron Microscopy (SEM). The results showed that the flexural and impact strengths would be increase with the increase of fiber length.

A 5-year evaluation using the talent endovascular graft for endovascular aneurysm repair in short aortic necks.

PubMed

Jim, Jeffrey; Sanchez, Luis A; Rubin, Brian G; Criado, Frank J; Fajardo, Andres; Geraghty, Patrick J; Sicard, Gregorio A

2010-10-01

Although endovascular aneurysm repair has been shown to be an effective way to treat abdominal aortic aneurysm (AAA), certain anatomic characteristics such as a short aortic neck, limit its applicability. Initially, commercially available devices were approved only for the treatment of AAA with an aortic neck length ≥ 15 mm. The purpose of this study was to evaluate the outcomes of the recently approved Talent endograft for AAAs with a short aortic neck length (10-15 mm). Data were obtained from the prospective, nonrandomized, multicenter Talent enhanced Low Profile Stent Graft System trial which enrolled patients between February 2002 and April 2003. A total of 154 patients with adequate preoperative imaging were identified for this study. Subgroup analyses were performed for AAA with 10-15 mm aortic neck and those with >15 mm neck. Safety and effectiveness endpoints were evaluated at 30 days, 1 year, and 5 years postprocedure. Patients treated with aortic neck lengths of 10-15 mm (n = 35) and those with >15 mm (n = 102) had similar age, gender, and risk factor profile. Both groups had similar preoperative aneurysm morphology in terms of maximum aneurysm size, degree of neck angulation, or proximal neck diameter. There were no statistically significant differences in freedom from major adverse events and mortality rates at 30 and 365 days. Similarly, there was no difference in the effectiveness endpoints at 12 months. At 5 years, there was no difference in migration rate, endoleaks, or change in aneurysm diameter from baseline. In addition, there is no difference in freedom from aneurysm-related mortality (94% vs. 99%). AAAs with short aortic necks (10-15 mm) and otherwise suitable anatomy for endovascular repair can be safely and effectively treated with the Talent endograft with excellent 1 and 5 year outcomes. Copyright © 2010. Published by Elsevier Inc.

Topographic anatomy of the great auricular point: landmarks for its localization and classification.

PubMed

Raikos, Athanasios; English, Thomas; Yousif, Omar Khalid; Sandhu, Mandeep; Stirling, Allan

2017-05-01

The great auricular point (GAP) marks the exit of the great auricular nerve at the posterior border of the sternocleidomastoid muscle (SCM). It is a key landmark for the identification of the spinal accessory nerve, and its intraoperative localization is vital to avoid neurological sequelae. This study delineates the topography and surface anatomy landmarks that used to localize the GAP. Thirty cadaveric heminecks were dissected on a layer-by-layer approach. The topography of the GAP was examined relative to the insertion point of the SCM at the clavicle, tip of the mastoid process, and angle of the mandible. The GAP and its relation to the SCM were determined as a ratio of the total length of the SCM. The GAP was demonstrated to be in a predictable location. The mean length of the SCM was 131.4 ± 22 mm, and the mean distance between the GAP and the mastoid process was found to be 60.4 ± 13.76 mm. The ratio of the GAP location to the total SCM length ranged between 0.33-0.57. The mean distance between the angle of the mandible and the GAP was determined to be 57 ± 22.2 mm. Based on the midpoint of the SCM, the GAP was above it in 66.7 % of subjects and classified to Type A, and below it in 33.3 % of subjects appointed to Type B. The anatomical landmarks utilized in this study are helpful in predicting the location of the GAP relative to the midpoint of the SCM and can reduce neural injuries within the posterior triangle of the neck.

Flight feather molt in Yellow-headed Blackbirds (Xanthocephalus xanthocephalus) in North Dakota

USGS Publications Warehouse

Twedt, Daniel J.; Linz, George M.

2015-01-01

Yellow-headed Blackbirds (Xanthocephalus xanthocephalus) in central North Dakota undergo prebasic molt or prejuvenile molt during late summer. Nestling Yellow-headed Blackbirds initiate a complete prejuvenile molt, grow their primary and secondary regimes in about 40 days, completing molt after they leave the nest by the first week in August. Remiges are not replaced during the subsequent preformative molt, being retained until the second prebasic molt. Nonlinear (logistic) regression of primary remex growth during definitive prebasic molts of Yellow-headed Blackbirds indicated 38 days were required to complete the linear phase of growth (between 10% and 90% of total primary length). Males added 19.5 mm/d and females added 15.7 mm/d to the total length of all primaries during this linear growth phase; an average of 4–5 mm per primary remex per day. Definitive prebasic molting of primary remiges in males and females was initiated in late June, after nesting and brood rearing were completed. Molts of Yellow-headed Blackbirds were completed by early September, before birds emigrated from North Dakota during mid-September. Because of their comparatively early completion of molt and emigration from the state, as well as their more diverse diet, agricultural depredation caused by Yellow-headed Blackbirds in North Dakota is likely less than that of Red-winged Blackbirds and Common Grackles.

Imaging of rat brain using short graded-index multimode fiber

NASA Astrophysics Data System (ADS)

Sato, Manabu; Kanno, Takahiro; Ishihara, Syoutarou; Suto, Hiroshi; Takahashi, Toshihiro; Kurotani, Reiko; Abe, Hiroyuki; Nishidate, Izumi

2014-03-01

Clinically it is important to image structures of brain at deeper areas with low invasions, for example, the pathological information is not obtained enough from the white matter. Preliminarily we have measured transmission images of rat brain using the short graded-index multimode fiber (SMMF) with the diameter of 140μm and length of 5mm. SMMF (core diameter, 100μm) was cut using a fiber cleaver and was fixed in a jig. Fiber lengths inside and outside jig were 3mm and 2mm, respectively. The jig was attached at the 20x objective lens. The conventional optical microscope was used to measure images. In basic characteristics, it was confirmed that the imaging conditions almost corresponded to calculations with the ray-transfer matrix and the spatial resolution was evaluated at about 4.4μm by measuring the test pattern. After euthanasia the rat parietal brain was excised with thickness around 1.5mm and was set on the slide glass. The tissue was illuminated through the slide glass by the bundle fiber with Halogen lamp. The tip of SMMF was inserted into the tissue by lifting the sample stage. The transmission image at each depth from 0.1mm to 1.53mm was measured. Around the depth of 1.45mm, granular structures with sizes of 4-5μm were recognized and corresponded to images by HE stained tissue. Total measurement time was within 2 hours. The feasibilities to image the depth of 5 mm with SMMF have been shown.

Asymmetric Outer Bow Length and Cervical Headgear Force System: 3D Analysis Using Finite Element Method.

PubMed

Geramy, Allahyar; Hassanpour, Mehdi; Emadian Razavi, Elham Sadat

2015-03-01

This study sought to assess distal and lateral forces and moments of asymmetric headgears by variable outer bow lengths. Four 3D finite element method (FEM) models of a cervical headgear attached to the maxillary first molars were designed in SolidWorks 2010 software and transferred to ANSYS Workbench ver. 11 software. Models contained the first molars, their periodontal ligament (PDL), cancellous and cortical bones, a mesiodistal slice of the maxillae and the headgear. Models were the same except for the outer bow length in headgears. The headgear was symmetric in model 1. In models 2 to 4, the headgears were asymmetric in length with differences of 5mm, 10mm and 15mm, respectively. A 2.5 N force in horizontal plane was applied and the loading manner of each side of the outer bow was calculated trigonometrically using data from a volunteer. The 15mm difference in outer bow length caused the greatest difference in lateral (=0.21 N) and distal (= 1.008 N) forces and also generated moments (5.044 N.mm). As the difference in outer bow length became greater, asymmetric effects increased. Greater distal force in the longer arm side was associated with greater lateral force towards the shorter arm side and more net yawing moment. A difference range of 1mm to 15 mm of length in cervical headgear can be considered as a safe length of outer bow shortening in clinical use.

Seasonal movement of brown trout in a southern Appalachian river

Treesearch

Kyle H. Burrell; J. Jeffery Isely; David B. Bunnell; David H. Van Lear; C. Andrew Dolloff

2000-01-01

Radio telemetry was used to evaluate the seasonal movement, activity level, and home range size of adult brown trout Salmo trutta in the Chattooga River watershed, one of the southernmost coldwater stream systems in the United States. In all, 27 adult brown trout (262-452 mm total length) were successfully monitored from 16 November 1995 to 15...

Comparative effects of constant versus fluctuating thermal regimens on yellow perch growth, feed conversion and survival

USDA-ARS?s Scientific Manuscript database

The effects of fluctuating or constant thermal regimens on growth, mortality, and feed conversion were determined for juvenile yellow perch (Perca flavescens). Yellow perch averaging 156mm total length and 43g body weight were held in replicate 288L circular tanks for 129 days under: 1) a diel therm...

[Assessment of resource situation of Collichthys lucidus in coastal waters of the Yangtze estuary].

PubMed

Hu, Yan; Zhang, Tao; Yang, Gang; Zhao, Feng; Hou, Jun-li; Zhang, Long-zhen; Zhuang, Ping

2015-09-01

In order to assess the resource status of Collichthys lucidus in coastal waters of Yangtze estuary, the growth and population parameters were studied by the length frequency distribution method based on the bottom trawl investigation data from 2012 to 2013. Von Bertalanffy growth parameters were calculated by using the ELEFAN module in FiSAT II software while the natural mortality rate (M) was estimated via Pauly's empirical equation. Besides, the Beverton-Holt dynamic model was developed to predict the variation trend of C. lucidus resource in coastal waters of Yangtze estuary. The results showed that in 2012-2013, a total of 4201 samples of C. lucidus with body lengths ranging from 18 to 155 mm were collected from the coastal waters of Yangtze estuary. The growth parameter (K) and limit length (L.) were 1.1 and 162.75 mm while the total mortality rate (Z), the natural mortality rate (M) and the fishing mortality rate (F) were 4.040, 1.683 and 2.357, respectively. Moreover, the current exploitation (E) of C. lucidus in coastal waters of Yangtze estuary was 0.583 per year, which was larger than Fopt (0.5). Corresponding to the average stock of 576.02 t, the resource amount of C. lucidus reached up to 1.33 x 10(8) individuals. These indicated that C. lucidus has been overfished in Yangtze estuary area.

Microdamage of the cortical bone during mini-implant insertion with self-drilling and self-tapping techniques: a randomized controlled trial.

PubMed

Yadav, Sumit; Upadhyay, Madhur; Liu, Sean; Roberts, Eugene; Neace, William P; Nanda, Ravindra

2012-05-01

The purpose of this research was to evaluate microdamage accumulation after mini-implant placement by self-drilling (without a pilot hole) and self-tapping (screwed into a pilot hole) insertion techniques. The null hypothesis was that the mini-implant insertion technique would have no influence on microcrack accumulation and propagation in the cortical bones of the maxillae and mandibles of adult hounds. Mini-implants (n = 162; diameter, 1.6 mm; length, 6 mm) were placed in the maxillae and mandibles of 9 hounds (12-14 months old) with self-drilling and self-tapping insertion techniques. The techniques were randomly assigned to the left or the right side of each jaw. Each hound received 18 mini-implants (10 in the mandible, 8 in the maxilla). Histomorphometric parameters including total crack length and crack surface density were measured. The null hypothesis was rejected in favor of an alternate hypothesis: that the self-drilling technique results in more microdamage (microcracks) accumulation in the adjacent cortical bone in both the maxilla and the mandible immediately after mini-implant placement. A cluster level analysis was used to analyze the data on the outcome measured. Since the measurements were clustered within dogs, a paired-samples t test was used to analyze the average differences between insertion methods at both jaw locations. A significance level of 0.05 was used for both analyses. The self-drilling technique resulted in greater total crack lengths in both the maxilla and the mandible (maxilla: mean difference, 18.70 ± 7.04 μm/mm(2); CI, 13.29-24.11; mandible: mean difference, 22.98 ± 6.43 μm/mm(2); CI, 18.04-27.93; P <0.05), higher crack surface density in both the maxilla and the mandible (maxilla: mean difference, 10.39 ± 9.16 μm/mm(2); CI, 3.34-17.43; mandible: mean difference, 11.28 ± 3.41 μm/mm(2); CI, 8.65-13.90; P <0.05). This study demonstrated greater microdamage in the cortical bones of adult hounds in both the maxilla and the mandible by the self-drilling insertion technique compared with the self-tapping technique. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

An intercomparison of the taxonomic and size composition of tropical macrozooplankton and micronekton collected using three sampling gears

NASA Astrophysics Data System (ADS)

Kwong, Lian E.; Pakhomov, Evgeny A.; Suntsov, Andrey V.; Seki, Michael P.; Brodeur, Richard D.; Pakhomova, Larisa G.; Domokos, Réka

2018-05-01

A micronekton intercalibration experiment was conducted off the southwest coast of Oahu Island, Hawaii in October 2004. Day and night samples were collected in the epipelagic and mesopelagic zones using three micronekton sampling gears: the Cobb Trawl, the Isaacs-Kidd Midwater Trawl (IKMT), and the Hokkaido University Frame Trawl (HUFT). Taxonomic composition and contribution by main size groups to total catch varied among gear types. However, the three gears exhibited similar taxonomic composition for macrozooplankton and micronekton ranging from 20 to 100 mm length (MM20-100). The HUFT and IKMT captured more mesozooplankton and small MM20-100, while the Cobb trawl selected towards larger MM20-100 and nekton. Taxonomic composition was described and inter-compared among gears. The relative efficacy of the three gears was assessed, and size dependent intercalibration coefficients were developed for MM20-100.

[Density, size structure and reproductive activity of the pink conch Eustrombus gigas (Mesogastropoda: Strombidae) in Banco Chinchorro, Mexico].

PubMed

Cala, Yuself R; Navarrete, Alberto de Jesús; Ocaña, Frank A; Rivera, José Oliva

2013-12-01

The pink conch Eustrombus gigas is an important fisheries resource. At the regional level in the Caribbean, over-exploitation and habitat destruction have caused a decrease in the abundance of this resource. In order to provide necessary information for the species management in Mexico, this work aimed to analyze the total density, adult density, size structure and reproductive behavior of pink conch population at Banco Chinchorro during 2009-2010. Data from three seasons were obtained (rainy, dry and cold fronts periods) in three areas: Norte (North), Centro (Center) and Sur (South). The organisms were separated into two groups: (a) the criteria based upon legal harvest in Mexico: legal size conchs (siphonal length > 200 mm) and illegal size conchs (siphonal length < 200 mm), and (b) the criteria based upon sexual maturity using the 15 mm lip thickness standard: lip < 15 mm as juvenile conch and lip > or = 15 mm as adult conch. Copulation, spawning, egg masses and aggregations were evaluated as reproductive evidences. The highest total density was observed during the dry season with 384ind./ha, and the lowest during the rainy season with 127ind./ha. The highest density was reported at Sur (385ind./ha) and the lowest at Norte (198ind./ ha). The highest adult density was observed during the rainy season (8.33ind./ha), and the lowest occurred in the dry season (6.1 ind./ha). Adult density values were 5.55, 7.05 and 8.33ind./ha for Centro, Sur and Norte areas, respectively. Adult densities were lower than the threshold needed for reproduction, and 42% of the population may be vulnerable to fishing, as they had the minimum size for catch (Lsi 200 mm). Furthermore, only 2.2% of the population reached a Gl > 15 mm as sexual maturity indicator. During the study period, only six evidences of reproductive activity were observed. The smaller densities reported at Banco Chinchorro may cause reproduction events to be almost absent which in turn is sufficient evidence to show that the Allee Effect is acting on the queen conch population and there is an urgent need of fishery closure. Three important points were proposed for management of queen conch at Banco Chinchorro: total closure of fishing, systematic assessment of the conch population and the implementation of conch fishing refuge.

Small plastic debris in sediments from the Central Adriatic Sea: Types, occurrence and distribution.

PubMed

Mistri, Michele; Infantini, Vanessa; Scoponi, Marco; Granata, Tommaso; Moruzzi, Letizia; Massara, Francesca; De Donati, Miriam; Munari, Cristina

2017-11-15

This is the first survey to investigate the occurrence and extent of microplastic contamination in sediments collected along a coast-open sea 140km-long transect in the Central Adriatic Sea. Plastic debris extracted from 64 samples of sediments were counted, weighted and identified by Fourier-transform infrared spectroscopy (FT-IR). Several types of plastic particles were observed in 100% of the stations. Plastic particles ranged from 1 to 30mm in length. The primary shape types by number were filaments (69.3%), followed by fragments (16.4%), and film (14.3%). Microplastics (1-5mm) accounted for 65.1% of debris, mesoplastics (5-20mm) made up 30.3% of total amount, while macro debris (>20mm) accounted for 4.6% of total plastics collected. Identification through FT-IR spectroscopy evidenced the presence of 6 polymer types: the majority of plastic debris were nylon, polyethylene and ethylene vinyl alcohol copolymer. Our data are a baseline for microplastic research in the Adriatic Sea. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Nomogram of Penile Length and Circumference in Iranian Term and Preterm Neonates.

PubMed

Soheilipour, Fahimeh; Rohani, Farzaneh; Dehkordi, Elham Hashemi; Isa Tafreshi, Roya; Mohagheghi, Parisa; Zaheriani, Seyed-Mohammadsalar; Jesmi, Fatemeh; Salehiniya, Hamid

2018-01-01

The normal length of penis in preterm and term neonates is different among different nations, and is affected by various factors. The present study aimed to determine stretched penile length (SPL) values and cutoff level of micropenis in term and preterm Iranian neonates, for the first time. All male neonates born in two general hospitals of Tehran (Akbarabadi, and Rasoul hospitals), center of Iran, with gestational age of 28-42 weeks were included and their SPL and penile circumference (PC) were examined on the first 3 days after birth by the same physician. Birth weight (BW), and height, gestational age, type of delivery, mother's age, twin/multiple pregnancy, drug, and medical history of mother during pregnancy were recorded and cutoff levels of two variables were calculated based on the collected variables for different gestational ages. Among a total of 587 neonates, 203 neonates were born term and 384 preterm. Mean ± SD of neonates' BW were 2,682.51 ± 739.30 (850-4800) gr. Mean ± SD of their SPL was 22.48 ± 3.34 mm; 25.92 ± 1.54 mm in term and 20.66 ± 2.50 mm in preterm infants ( P  = 0.001). Mean ± SD of PC was 6.71 ± 1.31 mm; 8.14 ± 0.48 in term and 5.96 ± 0.92 in preterm infants ( P  = 0.001). SPL and PC were significantly correlated with type of delivery, number of parity, gestational age, BW, and crown-heel length, head circumference ( P  < 0.001). This study suggested that SPL in male neonates was 22.48 mm and PC was 6.71 mm, both correlated with gestational age and BW. Due to the ethnical variety of this cutoff points and lack of an appropriate study in Iran, these cutoff points can be used by all physicians as a reference for Iranian newborns (term and preterm), in order to prevent misdiagnosis of micropenis and genital disorders.

Walleye age estimation using otoliths and dorsal spines: Preparation techniques and sampling guidelines based on sex and total length

USGS Publications Warehouse

Dembkowski, Daniel J.; Isermann, Daniel A.; Koenigs, Ryan P.

2017-01-01

We used dorsal spines and otoliths from 735 Walleye Sander vitreus collected from 35 Wisconsin water bodies to evaluate whether 1) otolith and dorsal spine cross sections provided age estimates similar to simpler methods of preparation (e.g., whole otoliths and dorsal spines, cracked otoliths); and 2) between-reader precision and differences between spine and otolith ages varied in relation to total length (TL), sex, and growth rate. Ages estimated from structures prepared using simpler techniques were generally similar to ages estimated using thin sections of dorsal spines and otoliths, suggesting that, in some instances, much of the additional processing time and specialized equipment associated with thin sectioning could be avoided. Overall, between-reader precision was higher for sectioned otoliths (mean coefficient of variation [CV] = 3.28%; standard error [SE] = 0.33%) than for sectioned dorsal spines (mean CV = 9.20%; SE = 0.56%). When using sectioned otoliths for age assignment, between-reader precision did not vary between sexes or growth categories (i.e., fast, moderate, slow), but between-reader precision was higher for females than males when using sectioned dorsal spines. Dorsal spines were generally effective at replicating otolith ages for male Walleye <450 mm TL and female Walleye <600 mm TL, suggesting that dorsal spines can be used to estimate ages for male Walleye <450 mm TL and female Walleye <600 mm TL. If sex is unknown, we suggest dorsal spines be used to estimate ages for Walleye <450 mm TL, but that otoliths be used for fish >450 mm TL. Our results provide useful guidance on structure and preparation technique selection for Walleye age estimation, thereby allowing biologists to develop sampling guidelines that could be implemented using information that is always (TL) or often (sex) available at the time of fish collection.

Histopathologic Findings of Cholecystectomy Specimens in Patients Who Underwent Donor Hepatectomy for Living Donor Liver Transplantation.

PubMed

Akbulut, S; Karagul, S; Ertugrul, I; Aydin, C; Yilmaz, M; Yilmaz, S

2015-06-01

The aim of this study was to discuss the macroscopic and microscopic properties of gallbladder specimens obtained from living liver donors. The study retrospectively analyzed the clinical and histopathological data of 1088 donors who underwent living donor hepatectomy between March 2005 and September 2014 at Inonu University Faculty of Medicine, Liver Transplantation Center. Age, sex, macroscopic, and microscopic properties of the gallbladder (bladder length, diameter, content, and histopathological properties) were recorded by 2 researchers. A total of 1009 donors aged 17 to 66 years (31.1 ± 9.5) met the inclusion criteria, whereas 79 donors were excluded due to missing data. In total, 587 donors were male (30.5 ± 9.1 years [16-63 years]) and 422 were female (31.8 ± 9.8 years [18-66 years]). Preoperative tests revealed Gilbert syndrome in 3 subjects, whereas other donors' biochemical tests were within normal ranges. The macroscopic examination of gallbladders revealed mean gallbladder wall thickness, length, and width of 1.82 ± 0.8 mm (1-10 mm), 72 ± 11.4 mm (40-120 mm), and 52.5 ± 14 mm (15-90 mm), respectively. The microscopic gallbladder examination showed that 740 donors had a normal gallbladder, 193 had chronic cholecystitis (1 donor had antral metaplasia and 1 had intestinal metaplasia), 40 had cholesterolosis (1 donor had both tubular adenoma and intestinal metaplasia), 15 had minimal chronic cholecystitis (1 donor had pyloric metaplasia), 14 had cholelithiasis, 2 had adenomyosis, 2 had muscular hypertrophy, 1 had papillary hyperplasia, 1 had microdiverticulitis, and 1 had mucosal lymphatic ectasia. The results of this study reflect the actual gallbladder pathologies that can be detected in healthy people. Clearer conclusions can be reached about the epidemiological data on gallbladder as the number of living liver donors increases in the future. Copyright © 2015 Elsevier Inc. All rights reserved.

Macroanatomic, light, and electron microscopic examination of pecten oculi in the seagull (Larus canus).

PubMed

Ince, Nazan Gezer; Onuk, Burcu; Kabak, Yonca Betil; Alan, Aydin; Kabak, Murat

2017-07-01

The present study was conducted to determine macroanatomic characteristic as well as light and electron microscopic examination (SEM) of pecten oculi and totally 20 bulbus oculi belonging to 10 seagulls (Larus canus) were used. Pecten oculi formations consisted of 18 to 21 pleats and their shape looked like a snail. Apical length of the pleats forming pecten oculi were averagely measured as 5.77 ± 0.56 mm, retina-dependent base length was 9.01 ± 1.35 mm and height was measured as 6.4 ± 0.62 mm. In pecten oculi formations which extend up to 1/3 of the bulbus oculi, two different vascular formations were determined according to thickness of the vessel diameter. Among these, vessels with larger diameters which are less than the others in count were classified as afferent and efferent vessels, smaller vessels which are greater in size were classified as capillaries. Furthermore, the granules which were observed intensely in apical side of the pleats of pecten oculi were observed to distribute randomly along the plica. © 2017 Wiley Periodicals, Inc.

Study of a scanning HIFU therapy protocol, Part II: Experiment and results

NASA Astrophysics Data System (ADS)

Andrew, Marilee A.; Kaczkowski, Peter; Cunitz, Bryan W.; Brayman, Andrew A.; Kargl, Steven G.

2003-04-01

Instrumentation and protocols for creating scanned HIFU lesions in freshly excised bovine liver were developed in order to study the in vitro HIFU dose response and validate models. Computer-control of the HIFU transducer and 3-axis positioning system provided precise spatial placement of the thermal lesions. Scan speeds were selected in the range of 1 to 8 mm/s, and the applied electrical power was varied from 20 to 60 W. These parameters were chosen to hold the thermal dose constant. A total of six valid scans of 15 mm length were created in each sample; a 3.5 MHz single-element, spherically focused transducer was used. Treated samples were frozen, then sliced in 1.27 mm increments. Digital photographs of slices were downloaded to computer for image processing and analysis. Lesion characteristics, including the depth within the tissue, axial length, and radial width, were computed. Results were compared with those generated from modified KZK and BHTE models, and include a comparison of the statistical variation in the across-scan lesion radial width. [Work supported by USAMRMC.

Tar, CO and delta 9THC delivery from the 1st and 2nd halves of a marijuana cigarette.

PubMed

Tashkin, D P; Gliederer, F; Rose, J; Chang, P; Hui, K K; Yu, J L; Wu, T C

1991-11-01

Previous in vitro studies suggest that, with successive puffs from a marijuana cigarette, delta-9-THC becomes concentrated in the remaining uncombusted portion of the cigarette. These observations are consistent with the common practice of smoking marijuana cigarettes to a smaller butt length than that to which tobacco cigarettes are smoked. The purpose of the present study was to compare the delivery of delta-9-THC, as well as total insoluble smoke particulates (tar) and carbon monoxide, from the distal ("first") versus the proximal ("second") halves of a standard marijuana cigarette during "natural" smoking of marijuana. On 4 separate days, ten habitual marijuana users smoked nearly all or approximately 1/2 of a standard marijuana cigarette (83 mm length; 800-900 mg; 1.24% THC), as follows: day 1, "whole" cigarette (60 mm smoked, leaving a 23-mm butt); day 2, "first" half (first 30 mm); day 3, "second" half (second 30 mm) after the "first" half was presmoked with a syringe; and day 4, "second" half after the "first" half was excised. A previously described smoking apparatus (20) was used for measurement of puff volume and inhaled tar. Puff volume and number were allowed to vary spontaneously (provided that the specified length of cigarette was consumed), while inhaled volume (1.5 liters), breathholding time (14 s) and interpuff interval (30 s) were held constant. Blood samples were withdrawn prior to smoking and serially after completion of smoking for analysis of blood carboxyhemoglobin (COHb) and serum delta-9-THC. Heart rate was measured before and 5 min after smoking. Subjects rated their level of "high" 20 min after completion of smoking.(ABSTRACT TRUNCATED AT 250 WORDS)

Effect of vitreous length and trephine size disparity on post-DALK refractive status.

PubMed

Javadi, Mohammad Ali; Feizi, Sepehr; Rastegarpour, Ali

2011-04-01

To evaluate the effect of vitreous length (distance between posterior lens surface and vitreoretinal interface) and donor-recipient disparity on the refraction and keratometric astigmatism after deep anterior lamellar keratoplasty (DALK). In this retrospective comparative study, 85 eyes of 83 patients with keratoconus underwent DALK using the big-bubble technique. A 0.25-mm oversize donor was used for a vitreous length of ≥ 16.0 mm, and a 0.50-mm oversize donor for a vitreous length of <16.0 mm. At least 3 months after complete suture removal, spherical equivalent refractive error (SE), keratometric astigmatism, and mean keratometry were compared between the 2 groups. Multiple regression analysis was performed in group 1 to investigate the correlation between vitreous length and SE, between vitreous length and keratometric astigmatism, and between mean keratometry and SE. Mean patient age was 26.5 ± 7.7 years, and they were followed for 22 ± 10 months postoperatively. Seventy-five eyes received a 0.25-mm oversize donor (group 1), and 10 had a donor oversized by 0.50 mm (group 2). Compared with group 1, the patients of group 2 had a significantly steeper cornea (46.83 ± 2.0 vs. 48.29 ± 1.9 diopters, respectively; P = 0.01). SE and keratometric astigmatism in group 1 did not significantly differ from those in group 2. In group 1, there was a significant association between vitreous length and SE and between mean keratometry and SE but not between vitreous length and keratometric astigmatism. In DALK, a donor oversized by 0.25 mm is advisable for elongated keratoconic eyes, whereas a 0.50-mm oversize donor is advocated for small ones.

[Chronologic, structural and biometric study of the egg and its development of the small spotted dogfish (Scyliorhinus canicula) raised in artificial seawater].

PubMed

Foulley, M M; Mellinger, J

1980-01-01

The eggs of the small spotted dogfish (Scyliorhinus canicula), developed in artificial sea water at 14 degrees C, pre-hatched after 3 to 3 1/2 months (total embryo length: 31 to 38 mm). Hatching occurred after 6 1/2 to 7 1/2 months (length of newborn: 80 to 95 mm). Egg weight first increased for 12 days and then remained constant until pre-hatching. A biometric study of the whole egg, egg case and albumen chamber showed very little variation in egg width, while egg length varied widely. As laying occurs in pairs, the secretory activity in each nidamental gland was observed to adapt to the extra volume of egg case contents in two cases where a double egg was laid with a normal one. However, the size and shape of the normal eggs of each female were generally distinctive, regardless of the contents or the external conditions. The egg case wall had three separate layers, as shown by microscopy of fresh material and experimental studies with various dyes.

Effect of differently structured and processed feedstuffs on diverse parameters of ethology and digestibility of growing rabbits and their influence on morphological structures in small intestine.

PubMed

Lang, Caroline; Hinchliffe, David; Brendle, Julia; Weirichl, Carmen; Hoy, Steffen

2016-01-01

The influence of different feedstuffs on parameters of digestion and ethology in growing rabbits (duration and number of feed intake, needed masticatory movements, pH value in stomach and small intestine, dry matter content of stomach chyme, level of destruction of cell structures in small intestine) was analysed. 384 five weeks old rabbits were fed with one of three feedstuffs: pellets (mean fibre length = 3 mm), fibre blocks (mean fibre length = 40 mm) and hay-oat-beat-ration (length of hay fibre ≥ 70 mm). The masticatory movements and duration for uptake 0.1 g of feedstuffs were measured in a special observation box. Rabbits in group cages were observed by 24 h video recording and duration and numbers of feed intakes were documented. After 8 weeks rabbits were slaughtered and pH values measured in stomach chyme (and dry matter content) and small intestine. Samples of them were taken and histologically examined (total length of villi and crypts, width of villi and degree of destruction determined by scores from 0 [= no destruction] to 3 [= severe destruction of villi]). Pellets lead to a faster feed intake with a lower number of masticatory movements. This equates a minor feeding time per feed intake and a higher amount of feedstuff in a shorter time. The dry matter content in stomach chyme increases and pH value was significantly higher there, but lower in duodenum. They also showed a significantly higher degree of destruction of villi, a shorter length and a larger width of villi than others.

Three-dimensional finite element analysis of stress distribution on different bony ridges with different lengths of morse taper implants and prosthesis dimensions.

PubMed

Toniollo, Marcelo Bighetti; Macedo, Ana Paula; Rodrigues, Renata Cristina Silveira; Ribeiro, Ricardo Faria; de Mattos, Maria da Gloria Chiarello

2012-11-01

This finite element analysis (FEA) compared stress distribution on different bony ridges rehabilitated with different lengths of morse taper implants, varying dimensions of metal-ceramic crowns to maintain the occlusal alignment. Three-dimensional FE models were designed representing a posterior left side segment of the mandible: group control, 3 implants of 11 mm length; group 1, implants of 13 mm, 11 mm and 5 mm length; group 2, 1 implant of 11 mm and 2 implants of 5 mm length; and group 3, 3 implants of 5 mm length. The abutments heights were 3.5 mm for 13- and 11-mm implants (regular), and 0.8 mm for 5-mm implants (short). Evaluation was performed on Ansys software, oblique loads of 365N for molars and 200N for premolars. There was 50% higher stress on cortical bone for the short implants than regular implants. There was 80% higher stress on trabecular bone for the short implants than regular implants. There was higher stress concentration on the bone region of the short implants neck. However, these implants were capable of dissipating the stress to the bones, given the applied loads, but achieving near the threshold between elastic and plastic deformation to the trabecular bone. Distal implants and/or with biggest occlusal table generated greatest stress regions on the surrounding bone. It was concluded that patients requiring short implants associated with increased proportions implant prostheses need careful evaluation and occlusal adjustment, as a possible overload in these short implants, and even in regular ones, can generate stress beyond the physiological threshold of the surrounding bone, compromising the whole system.

Relationship of lake herring (Coregonus artedi) gill raker characteristics to retention probabilities of zooplankton prey

USGS Publications Warehouse

Link, Jason; Hoff, Michael H.

1998-01-01

We measured morphometric and meristic parameters of gill rakers from the first gill arch of 36 adult lake herring (Coregonus artedi) from Lake Superior that ranged in length from 283–504 mm. These data, coupled with the mean of the smallest two body dimensions (length, width, or breadth) of various zooplankton prey, allowed us to calculate retention probabilities for zooplankton taxa that are common in Lake Superior. The mean of the smallest two body dimensions was positively correlated with body length for cladocerans and copepods. The large cladoceran, Daphnia g. mendotae, is estimated to be retained at a greater probability (74%) than smaller cladocerans (18%-38%). The same is true for the large copepod, Limnocalanus macrurus (60%), when compared to smaller copepods (6–38%). Copepods have a lower probability of being retained than cladocerans of similar length. Lake herring gill rakers and total filtering area are also positively correlated with fish total length. These data provide further evidence that lake herring are primarily planktivores in Lake Superior, and our data show that lake herring can retain a broad range of prey sizes.

Dual-slot antennas for microwave tissue heating: parametric design analysis and experimental validation.

PubMed

Brace, Christopher L

2011-07-01

Design and validate an efficient dual-slot coaxial microwave ablation antenna that produces an approximately spherical heating pattern to match the shape of most abdominal and pulmonary tumor targets. A dual-slot antenna geometry was utilized for this study. Permutations of the antenna geometry using proximal and distal slot widths from 1 to 10 mm separated by 1-20 mm were analyzed using finite-element electromagnetic simulations. From this series, the most optimal antenna geometry was selected using a two-term sigmoidal objective function to minimize antenna reflection coefficient and maximize the diameter-to-length aspect ratio of heat generation. Sensitivities to variations in tissue properties and insertion depth were also evaluated in numerical models. The most optimal dual-slot geometry of the parametric analysis was then fabricated from semirigid coaxial cable. Antenna reflection coefficients at various insertion depths were recorded in ex vivo bovine livers and compared to numerical results. Ablation zones were then created by applying 50 W for 2-10 min in simulations and ex vivo livers. Mean zone diameter, length, aspect ratio, and reflection coefficients before and after heating were then compared to a conventional monopole antenna using ANOVA with post-hoc t-tests. Statistical significance was indicated for P <0.05. Antenna performance was highly sensitive to dual-slot geometry. The best-performing designs utilized a proximal slot width of 1 mm, distal slot width of 4 mm +/- 1 mm and separation of 8 mm +/- 1 mm. These designs were characterized by an active choking mechanism that focused heating to the distal tip of the antenna. A dual-band resonance was observed in the most optimal design, with a minimum reflection coefficient of -20.9 dB at 2.45 and 1.25 GHz. Total operating bandwidth was greater than 1 GHz, but the desired heating pattern was achieved only near 2.45 GHz. As a result, antenna performance was robust to changes in insertion depth and variations in relative permittivity of the surrounding tissue medium. In both simulations and ex vivo liver, the dual-slot antenna created ablations greater in diameter than a coaxial monopole (35 mm +/- 2 mm versus 31 mm +/- 2 mm; P<0.05), while also shorter in length (49 mm +/- 2 mm versus 60 mm +/- 6 mm; P < 0.001) after 10 min. Similar results were obtained after 2 and 5 min as well. Dual-slot antennas can produce more spherical ablation zones while retaining low reflection coefficients. These benefits are obtained without adding to the antenna diameter. Further evaluation for clinical microwave ablation appears warranted.

Is short stature associated with short cervical length?

PubMed

Gagel, Caroline K; Rafael, Timothy J; Berghella, Vincenzo

2010-10-01

We sought to estimate if there is a correlation between maternal height and cervical length in women at high risk for preterm birth. We studied a retrospective cohort of women with singleton gestation and risk factors for preterm birth. Maternal height was categorized as short (<157.5 cm) or not short stature (≥157.5 cm). Cervical length at 14 to 24 weeks was evaluated. Primary outcomes were incidence of initial cervical length <30 mm and incidence of shortest cervical length <25 mm. Four hundred sixteen women met the inclusion criteria. Twenty-two (22.6%) of the short women and 79 (24.5%) of the nonshort women had an initial cervical length <30 mm ( P = 0.81). Twenty-two (23.7%) of the short women and 104 (32.2%) of the nonshort women had a cervical length <25 mm for shortest cervical length measurement ( P = 0.15). In women with singleton gestation and risk factors for preterm birth, no statistically significant relationship exists between maternal height and initial or shortest cervical length. © Thieme Medical Publishers.

Asymmetric Outer Bow Length and Cervical Headgear Force System: 3D Analysis Using Finite Element Method

PubMed Central

Geramy, Allahyar; Hassanpour, Mehdi; Emadian Razavi, Elham sadat

2015-01-01

Objectives: This study sought to assess distal and lateral forces and moments of asymmetric headgears by variable outer bow lengths. Materials and Methods: Four 3D finite element method (FEM) models of a cervical headgear attached to the maxillary first molars were designed in SolidWorks 2010 software and transferred to ANSYS Workbench ver. 11 software. Models contained the first molars, their periodontal ligament (PDL), cancellous and cortical bones, a mesiodistal slice of the maxillae and the headgear. Models were the same except for the outer bow length in headgears. The headgear was symmetric in model 1. In models 2 to 4, the headgears were asymmetric in length with differences of 5mm, 10mm and 15mm, respectively. A 2.5 N force in horizontal plane was applied and the loading manner of each side of the outer bow was calculated trigonometrically using data from a volunteer. Results: The 15mm difference in outer bow length caused the greatest difference in lateral (=0.21 N) and distal (= 1.008 N) forces and also generated moments (5.044 N.mm). Conclusion: As the difference in outer bow length became greater, asymmetric effects increased. Greater distal force in the longer arm side was associated with greater lateral force towards the shorter arm side and more net yawing moment. Clinical Relevance: A difference range of 1mm to 15 mm of length in cervical headgear can be considered as a safe length of outer bow shortening in clinical use. PMID:26622275

Corneal Thickness Profile and Associations in Chinese Children Aged 7 to 15 Years Old.

PubMed

Ma, Yingyan; Zhu, Xiaofeng; He, Xiangui; Lu, Lina; Zhu, Jianfeng; Zou, Haidong

2016-01-01

Corneal thickness (CT) maps of the central (2-mm diameter), para-central (2 to 5-mm diameter), peripheral (5 to 6-mm diameter), and minimum (5-mm diameter) cornea were measured in normal Chinese school children aged 7 to 15 years old using Fourier-domain optical coherence tomography. Multiple regression analyses were performed to explore the effect of associated factors [age, gender, refraction, axial length and corneal curvature radius (CCR)] on CT and the relationship between central corneal thickness (CCT) and intraocular pressure (IOP). A total of 1228 eyes from 614 children were analyzed. The average CCT was 532.96 ± 28.33 μm for right eyes and 532.70 ±28.45 μm for left eyes. With a 10 μm increase in CCT, the IOP was elevated by 0.37 mm Hg, as measured by noncontact tonometry. The CT increased gradually from the center to the periphery. The superior and superior nasal regions had the thickest CTs, while the thinnest points were primarily located in the inferior temporal cornea. The CCT was associated with CCR (p = 0.008) but not with gender (p = 0.075), age (p = 0.286), axial length (p = 0.405), or refraction (p = 0.985). In the para-central region and the peripheral cornea, increased CT was associated with younger age, male gender, and a flatter cornea.

Flower, fruit phenology and flower traits in Cordia boissieri (Boraginaceae) from northeastern Mexico

PubMed Central

Martínez-Adriano, Cristian Adrian; Flores, Joel; González-Rodríguez, Humberto; Cuéllar-Rodríguez, Gerardo

2016-01-01

We characterized variations in Cordia boissieri flowers and established if these variations occur between plants or between flowering events. Flowering and fruiting was measured for 256 plants. A GLM test was used to determine the relationship between flowering and fruit set processes and rainfall. We performed measurements of floral traits to detect variations within the population and between flowering events. The position of the anthers with respect to the ovary was determined in 1,500 flowers. Three out of four flowering events of >80% C. boissieri plants occurred after rainfall events. Only one flowering event occurred in a drought. Most plants flowered at least twice a year. The overlapping of flowering and fruiting only occurred after rainfall. Anthesis lasted three-to-five days, and there were two flower morphs. Half of the plants had longistylus and half had brevistylus flowers. Anacahuita flower in our study had 1–4 styles; 2–9 stamens; 6.5–41.5 mm long corolla; sepals from 4.5–29.5 mm in length; a total length from 15.5–59 mm; a corolla diameter from 10.5–77 mm. The nectar guide had a diameter from 5–30.5 mm; 4–9 lobes; and 5 distinguishable nectar guide colors. The highest variation of phenotypic expression was observed between plants. PMID:27231656

Ontogeny of serotonin-immunoreactive cells in the gut epithelium of the cloudy dogfish, Scyliorhinus torazame, with reference to coexistence of serotonin and neuropeptide Y.

PubMed

Chiba, A

1998-09-01

The ontogeny of serotonin (5-HT)-immunoreactive (IR) cells in the gut epithelium of an oviparous elasmobranch, Scyliorhinus torazame, was examined immunohistochemically. 5-HT-IR cells first appeared in the proximal part of the vitellointestinal duct (VID) and in the anterior part of the midgut of the embryo (30 mm in total length). At the 40-mm stage, the cells slightly increased in number and spread to the posterior part of the midgut, but no labeled cells were found in the foregut or hindgut. By the late embryonic (74- and 80-mm) stages, 5-HT-IR cells were markedly increased in number in the spiral intestine and stomach, whereas they were few in the VID and rectum. During these stages, the density of the cells in the inner yolk sac, the derivative of the VID, tended to be increased. This tendency seemed to be consistent in the posthatching juveniles at the 95-mm stage. In juveniles, 125 mm in length and 1.7 months after hatching, the cells further increased in number in the spiral intestine, reaching their adult value. Double immunostaining by the use of anti-5-HT and -neuropeptide Y (NPY) antisera demonstrated that some of the 5-HT-IR cells were also positive for NPY. Copyright 1998 Academic Press.

2000W high beam quality diode laser for direct materials processing

NASA Astrophysics Data System (ADS)

Qin, Wen-bin; Liu, You-qiang; Cao, Yin-hua; Gao, Jing; Pan, Fei; Wang, Zhi-yong

2011-11-01

This article describes high beam quality and kilowatt-class diode laser system for direct materials processing, using optical design software ZEMAX® to simulate the diode laser optical path, including the beam shaping, collimation, coupling, focus, etc.. In the experiment, the diode laser stack of 808nm and the diode laser stack of 915nm were used for the wavelength coupling, which were built vertical stacks up to 16 bars. The threshold current of the stack is 6.4A, the operating current is 85A and the output power is 1280W. Through experiments, after collimating the diode laser beam with micro-lenses, the fast axis BPP of the stack is less than 60mm.mrad, and the slow-axis BPP of the stack is less than 75mm.mrad. After shaping the laser beam and improving the beam quality, the fast axis BPP of the stack is still 60mm.mrad, and the slow-axis BPP of the stack is less than 19mm.mrad. After wavelength coupling and focusing, ultimately the power of 2150W was obtained, focal spot size of 1.5mm * 1.2mm with focal length 300mm. The laser power density is 1.2×105W/cm2, and that can be used for metal remelting, alloying, cladding and welding. The total optical coupling conversion efficiency is 84%, and the total electrical - optical conversion efficiency is 50%.

A vacuum-sealed miniature X-ray tube based on carbon nanotube field emitters

NASA Astrophysics Data System (ADS)

Heo, Sung Hwan; Kim, Hyun Jin; Ha, Jun Mok; Cho, Sung Oh

2012-05-01

A vacuum-sealed miniature X-ray tube based on a carbon nanotube field-emission electron source has been demonstrated. The diameter of the X-ray tube is 10 mm; the total length of the tube is 50 mm, and no external vacuum pump is required for the operation. The maximum tube voltage reaches up to 70 kV, and the X-ray tube generates intense X-rays with the air kerma strength of 108 Gy·cm2 min-1. In addition, X-rays produced from the miniature X-ray tube have a comparatively uniform spatial dose distribution.

A portable high power microwave source with permanent magnets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Wei; Zhang, Jun; Li, Zhi-qiang

A high power microwave source with permanent magnets is proposed in this paper. The source has the length 330 mm, maximum diameter 350 mm, and total weight 50 kg, including 25 kg of permanent magnets. 1 GW of microwave power with Gaussian radiation pattern and 24% of microwave power generation efficiency in a pulse duration of 75 ns are obtained in the experiment. Operating frequency of the source is 2.32 GHz. Such a small size, light weight, and highly stable in operation source will be used in portable repetitive high power microwave generation systems.

Impact of renal anatomy on shock wave lithotripsy outcomes for lower pole kidney stones: results of a prospective multifactorial analysis controlled by computerized tomography.

PubMed

Torricelli, Fabio C M; Marchini, Giovanni S; Yamauchi, Fernando I; Danilovic, Alexandre; Vicentini, Fabio C; Srougi, Miguel; Monga, Manoj; Mazzucchi, Eduardo

2015-06-01

We evaluated which variables impact fragmentation and clearance of lower pole calculi after shock wave lithotripsy. We prospectively evaluated patients undergoing shock wave lithotripsy for a solitary 5 to 20 mm lower pole kidney stone between June 2012 and August 2014. Patient body mass index and abdominal waist circumference were recorded. One radiologist blinded to shock wave lithotripsy outcomes measured stone size, area and density, stone-to-skin distance, infundibular length, width and height, and infundibulopelvic angle based on baseline noncontrast computerized tomography. Fragmentation, success (defined as residual fragments less than 4 mm in asymptomatic patients) and the stone-free rate were evaluated by noncontrast computerized tomography 12 weeks postoperatively. Univariate and multivariate analysis was performed. A total of 100 patients were enrolled in the study. Mean stone size was 9.1 mm. Overall fragmentation, success and stone-free rates were 76%, 54% and 37%, respectively. On logistic regression body mass index (OR 1.27, 95% CI 1.11-1.49, p = 0.004) and stone density (OR 1.0026, 95% CI 1.0008-1.0046, p = 0.005) significantly impacted fragmentation. Stone size (OR 1.24, 95% CI 1.07-1.48, p = 0.039) and stone density (OR 1.0021, 95% CI 1.0007-1.0037, p = 0.012) impacted the success rate while stone size (OR 1.24, 95% CI 1.04-1.50, p = 0.029), stone density (OR 1.0015, 95% CI 1.0001-1.0032, p = 0.046) and infundibular length (OR 1.1035, 95% CI 1.015-1.217, p = 0.015) impacted the stone-free rate. The best outcomes were found in patients with a body mass index of 30 kg/m(2) or less, stones 10 mm or less and 900 HU or less, and an infundibular length of 25 mm or less. The coexistence of significant unfavorable variables led to a stone-free rate of less than 20%. Obese patients with higher than 10 mm density stones (greater than 900 HU) in the lower pole of the kidney with an infundibular length of greater than 25 mm should be discouraged from undergoing shock wave lithotripsy. Copyright © 2015 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

Asymmetry in Femoral Tunnel Socket Length During Anterior Cruciate Ligament Reconstruction With Transportal, Outside-In, and Modified Transtibial Techniques.

PubMed

Osaki, Kanji; Okazaki, Ken; Matsubara, Hirokazu; Kuwashima, Umito; Murakami, Koji; Iwamoto, Yukihide

2015-12-01

To investigate the mismatch between the length at the center and the length on the shortest and longest peripheral sides of the femoral tunnel socket, reamed with the transportal (TP), outside-in (OI), and modified transtibial (TT) techniques, in anterior cruciate ligament (ACL) reconstruction. Femoral tunnel drilling was simulated on 3-dimensional bone models from 40 subjects. The tunnel directions used with the TP, OI, and modified TT techniques were previously described. By use of the resulting angle, a femoral tunnel socket of 9 mm in diameter was drilled from the center of the femoral ACL insertion. The virtual femoral tunnel was extracted, and the length mismatch was measured between the center and the shortest and longest peripheral sides of the tunnel socket. The mean socket length mismatch between the center and the shortest peripheral part of the femoral tunnel socket was 4.2 ± 0.9 mm with the TP technique, 5.2 ± 1.3 mm with the OI technique, and 3.2 ± 0.8 mm with the modified TT technique. The mean socket length mismatch between the center and the longest peripheral part of the femoral tunnel socket was 3.5 ± 0.9 mm with the TP technique, 4.8 ± 1.5 mm with the OI technique, and 3.3 ± 1.2 mm with the modified TT technique. The length mismatch was significantly higher when the tunnel socket was created by the OI technique (P < .01). A length mismatch with the tunnel socket exists after reaming with either the TP, OI, or modified TT technique. In particular, there was a significant increase in length mismatch when the tunnel socket was created by the OI technique, and the length mismatch would easily become greater than 5 mm. The surgeon should recognize this mismatch when it is created and measure the femoral tunnel socket. In anatomic ACL reconstruction, a mismatch between the length at the center and the length at periphery of the femoral tunnel socket occurs, and this is increased particularly when using the OI technique. The discrepancy in tunnel length between its center and its periphery could cause an overestimation of the tunnel length that could result in an error in length during graft preparation. Copyright © 2015 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

A comparison of lead lengths for mini-fyke nets to sample age-0 gar species

USGS Publications Warehouse

Long, James M.; Snow, Richard A.; Patterson, Chas P.

2016-01-01

Mini-fyke nets are often used to sample small-bodied fishes in shallow (<1 m depth) water, especially in vegetated shoreline habitats where seines are ineffective. Recent interest in gar (Lepisosteidae) ecology and conservation led us to explore the use of mini-fyke nets to capture age-0 gar and specifically how capture is affected by lead length of the fyke net. In the summers of 2012, 2013, and 2015, mini-fyke nets with two different lead lengths (4.57 m and 9.14 m) were set at random sites in backwaters and coves of the Red River arm of Lake Texoma, Oklahoma. Mean CPUE (catch-per-unit-effort; number per net night) was significantly lower for mini-fyke nets with short leads (0.52) compared to those with long leads (1.51). Additionally, Spotted Gar (Lepisosteus oculatus) were captured at a higher rate than the other three gar species present in Lake Texoma, although this could have been an artifact of sampling location. We found that differences in length-frequency of captured gar between gear types were nearly significant, with total length ranging from 47mm to 590mm. Mini-fyke nets with longer leads increased the efficiency of sampling for age-0 gar by increasing catch rate without affecting estimates of other population parameters and appear to be useful for this purpose. 

Chapter 2: American marten

Treesearch

Steven W. Buskirk; Leonard F. Ruggiero

1994-01-01

The American marten (Martes americana), also called the marten or American sable, is a carnivorous mammal about the size of a small house cat. Its total length is between 500 and 680 mm and it weighs 500-1400 g as an adult, depending on sex and geography (Buskirk and McDonald 1989; Strickland et al. 1982). The male is 20-40% larger than, but...

Mode selection and tuning of single-frequency short-cavity VECSELs

DOE PAGES

Serkland, Darwin K.; So, Haley M.; Peake, Gregory M.; ...

2018-03-05

Here, we report on mode selection and tuning properties of vertical-external-cavity surface-emitting lasers (VECSELs) containing coupled semiconductor and external cavities of total length less than 1 mm. Our goal is to create narrowlinewidth (<1MHz) single-frequency VECSELs that operate near 850 nm on a single longitudinal cavity resonance and tune versus temperature without mode hops. We have designed, fabricated, and measured VECSELs with external-cavity lengths ranging from 25 to 800 μm. Lastly, we compare simulated and measured coupled-cavity mode frequencies and discuss criteria for single mode selection.

Dynamics of an introduced and unexploited Lake Whitefish population in Lake Pend Oreille, Idaho

USGS Publications Warehouse

Hosack, Michael A.; Hansen, Michael J.; Horner, Ned J.

2014-01-01

To evaluate biological potential of a commercial fishery for an unexploited Lake Whitefish Coregonus clupeaformis population in Lake Pend Oreille, Idaho, we estimated population parameters related to production and yield. The length frequency based on trap-netting in autumn 2005 was normal with a mean of 448 mm TL, whereas the length frequency based on gillnetting in spring 2006 was bimodal with a mean of 390 mm TL. Sex composition was skewed toward females (0.66) during autumn trap-netting. Shape parameters β of weight–length models for females (β = 3.38) and males (β = 3.45) were similar to those of other unexploited populations. Instantaneous growth rates K for females (K = 0.144 per year) and males (K = 0.153 per year) were among the lowest for unexploited populations across the species’ range. Age at 50% maturity (females: 6.5 years; males: 6.0 years) and length at 50% maturity (females: 390 mm TL; males: 378 mm TL) were high for unexploited populations. The natural mortality rate M (0.149 per year, ages 11–36) was among the lowest observed for unexploited populations. Adult population density was lower than that of other populations based on total surface area (mean = 1.35 fish/ha; 95% confidence interval [CI] = 1.11–1.78 fish/ha) but was average based on lake area shallower than 70 m (4.07 fish/ha; 95% CI = 3.35–5.35 fish/ha). Population density of juveniles and adults averaged 84 fish/ha (95% CI = 52–143 fish/ha) over the entire surface area and 278 fish/ha (95% CI = 173–474 fish/ha) over depths shallower than 70 m. The difference between the low M of the unexploited population in Lake Pend Oreille (M = 0.149 per year; annual mortality rate A = 14%) and the high sustainable total mortality Z of exploited stocks in the Laurentian Great Lakes (Z = 1.204; A = 70%) suggests a large scope for sustainable fishing mortality F (1.055 per year; exploitation rate u = 61%) that is equivalent to a sustainable Lake Whitefish harvest of 55,000 individuals (50,000–60,000 individuals) and 49,000 kg (45,000–54,000 kg) from Lake Pend Oreille.

Investigation of two-phase thermosyphon performance filled with modern HFC refrigerants

NASA Astrophysics Data System (ADS)

Gorecki, Grzegorz

2018-02-01

Two-phase closed thermosyphons (TPCTs) are widely utilized as heat exchanger elements in waste heat recovery systems and as passive heating/cooling devices. They are popular because of their high thermal conductivity, simple construction and reliability. Previous researches indicate that refrigerants are performing better than typical TPCT working fluids like deionized water or alcohols in the low temperature range. In the present study three HFC (Hydrofluorocarbons) refrigerants were tested: R134a, R404A and R407C. The total length of the investigated TPCT is 550 mm with equal length (245 mm) condenser and evaporator sections. Its outer diameter is 22 mm with 1 mm wall thickness. The evaporator section was heated by hot water with varying inlet temperature by 5 K step in the range of 288 K - 323 K. The condenser was cooled by cold water with inlet temperature kept at a constant value of 283 K. It was found that using R134a and R404A as working fluids heat transfer rates are the highest. For both refrigerants 10% is optimal filling ratio. They can be utilized interchangeably because the differences between their throughputs are within uncertainty bands. R407C performance was 50% lower. Other disadvantages of using this refrigerant are relatively high working pressures and higher optimal filling ratio (30%).

Investigation of two-phase thermosyphon performance filled with modern HFC refrigerants

NASA Astrophysics Data System (ADS)

Gorecki, Grzegorz

2018-07-01

Two-phase closed thermosyphons (TPCTs) are widely utilized as heat exchanger elements in waste heat recovery systems and as passive heating/cooling devices. They are popular because of their high thermal conductivity, simple construction and reliability. Previous researches indicate that refrigerants are performing better than typical TPCT working fluids like deionized water or alcohols in the low temperature range. In the present study three HFC (Hydrofluorocarbons) refrigerants were tested: R134a, R404A and R407C. The total length of the investigated TPCT is 550 mm with equal length (245 mm) condenser and evaporator sections. Its outer diameter is 22 mm with 1 mm wall thickness. The evaporator section was heated by hot water with varying inlet temperature by 5 K step in the range of 288 K - 323 K. The condenser was cooled by cold water with inlet temperature kept at a constant value of 283 K. It was found that using R134a and R404A as working fluids heat transfer rates are the highest. For both refrigerants 10% is optimal filling ratio. They can be utilized interchangeably because the differences between their throughputs are within uncertainty bands. R407C performance was 50% lower. Other disadvantages of using this refrigerant are relatively high working pressures and higher optimal filling ratio (30%).

Visualization of lenticulostriate arteries at 3T: Optimization of slice-selective off-resonance sinc pulse-prepared TOF-MRA and its comparison with flow-sensitive black-blood MRA.

PubMed

Okuchi, Sachi; Okada, Tomohisa; Fujimoto, Koji; Fushimi, Yasutaka; Kido, Aki; Yamamoto, Akira; Kanagaki, Mitsunori; Dodo, Toshiki; Mehemed, Taha M; Miyazaki, Mitsue; Zhou, Xiangzhi; Togashi, Kaori

2014-06-01

To optimize visualization of lenticulostriate artery (LSA) by time-of-flight (TOF) magnetic resonance angiography (MRA) with slice-selective off-resonance sinc (SORS) saturation transfer contrast pulses and to compare capability of optimal TOF-MRA and flow-sensitive black-blood (FSBB) MRA to visualize the LSA at 3T. This study was approved by the local ethics committee, and written informed consent was obtained from all the subjects. TOF-MRA was optimized in 20 subjects by comparing SORS pulses of different flip angles: 0, 400°, and 750°. Numbers of LSAs were counted. The optimal TOF-MRA was compared to FSBB-MRA in 21 subjects. Images were evaluated by the numbers and length of visualized LSAs. LSAs were significantly more visualized in TOF-MRA with SORS pulses of 400° than others (P < .003). When the optimal TOF-MRA was compared to FSBB-MRA, the visualization of LSA using FSBB (mean branch numbers 11.1, 95% confidence interval (CI) 10.0-12.1; mean total length 236 mm, 95% CI 210-263 mm) was significantly better than using TOF (4.7, 95% CI 4.1-5.3; 78 mm, 95% CI 67-89 mm) for both numbers and length of the LSA (P < .0001). LSA visualization was best with 400° SORS pulses for TOF-MRA but FSBB-MRA was better than TOF-MRA, which indicates its clinical potential to investigate the LSA on a 3T magnetic resonance imaging. Copyright © 2014 AUR. Published by Elsevier Inc. All rights reserved.

A novel electromagnetic navigation tool for acetabular surgery.

PubMed

Lehmann, Wolfgang; Rueger, Johannes M; Nuechtern, Jakob; Grossterlinden, Lars; Kammal, Michael; Hoffmann, Michael

2015-10-01

Acetabular fracture surgery is demanding and screw placement along narrow bony corridors remains challenging. It necessitates x-ray radiation for fluoroscopically assisted screw insertion. The purpose of this cadaver study was to evaluate the feasibility, accuracy and operation time of a novel electromagnetic navigation system for screw insertion along predefined acetabular corridors. A controlled laboratory study with a total of 24 electromagnetically navigated screw insertions was performed on 8 cadaveric acetabula. 3 peri-acetabular bony corridors (QSS, Quadrilateral Surface Screw; IAS, Infra-Acetabular Screw; PCS, Posterior Column Screw) were defined and screws were placed in a defined order without fluoroscopy. Operation time was documented. Postoperative CT scans were performed to analyse accuracy of screw placement. Mean cadaver age was 70.4 ± 11.7. Successful screw placement was accomplished in 22 out of 24 (91.7%) cases. The overall mean time for all 3 acetabular screws was 576.6 ± 75.9s. All 3 complications occurred during the placement of the IAS due to an impassable narrow bony corridor. QSS mean length was 50 ± 5mm, IAS mean length was 85 ± 10mm and PCS mean length was 120 ± 5mm. In this cadaver study the novel electromagnetic navigation system was feasible to allow accurate screw placement without fluoroscopy in defined narrow peri-acetabular bony corridors. Copyright © 2015 Elsevier Ltd. All rights reserved.

A Military Guide to Terrorism in the Twenty-First Century. U.S. Army DCSINT Handbook No. 1 (Version 3.0)

DTIC Science & Technology

2005-08-15

or varnished brown Length: 102mm Width: 61mm Weight: 773g Filler: Amatol Characteristics Color: Black and unmarked Length: 131mm Width: 55mm...isocyanate Diborane Boron tribromide Nitrogen dioxide Ethylene oxide Carbon monoxide Phosphine Fluorine Carbonyl sulfide Phosphorus oxychloride

Fishery biology of jumbo flying squid Dosidicus gigas off Costa Rica Dome

NASA Astrophysics Data System (ADS)

Chen, Xinjun; Li, Jianghua; Liu, Bilin; Li, Gang; Lu, Huajie

2014-06-01

The jumbo flying squid ( Dosidicus gigas) population was surveyed with the help of Chinese squid jigging vessels off the Costa Rica Dome (4°-11°N, 90°-100°W) in 2009 and 2010. The daily catch of D. gigas in the two survey cruises ranged from 0 to 5.5 t and was mostly obtained from the areas bounded by 6°-9°N and 91°-94°W and by 6°30'-7°30'N and 96°-97°W. The sea surface temperature in the areas yielding the most catch ranged from 27.5 to 29°C. The sex ratio of the total catch was 3.75:1 (female: male). The mantle length of the squid ranged from 211 to 355 mm (male) and from 204 to 429 mm (female) with an average of 297.9 and 306.7 mm, respectively. In the relationship of the mantle length (mm) and body weight (g) of the squid, there was no significant difference between sexes. The female and male were at a similar maturity, and most individuals are maturing or have matured with a few females being spent. The size (mantle length) and age at the first sexual maturity were 297 mm and 195 d in females, and less than 211 mm and 130 d in males, respectively. Most of the sampled stomachs (70.6%) had no food remains. The major preys of the squids were fish, cephalopods and crustaceans, with the most abundant Myctophum orientale and D. gigas. The preys in more than 65% of the non-empty sampled stomachs evidenced the cannibalism of D. gigas. The results improved current understanding of the fishery biology of D. gigas off the Costa Rica Dome, which may facilitate the assessment and management of relative fishery resources.

Effect of realistic vehicle seats, cushion length, and lap belt geometry on child ATD kinematics.

DOT National Transportation Integrated Search

2011-12-01

This series of sled tests examined the effect of using real vehicle seats on child ATD performance. Cushion length was varied from production length of 450 mm to a shorter length of 350 mm. Lap belt geometry was set to rear, mid, and forward anchorag...

Effect of fiber post length and abutment height on fracture resistance of endodontically treated premolars prepared for zirconia crowns.

PubMed

Lin, Jie; Matinlinna, Jukka Pekka; Shinya, Akikazu; Botelho, Michael George; Zheng, Zhiqiang

2018-04-01

The purpose of this study was to compare the fracture resistance, mode of fracture, and stress distribution of endodontically treated teeth prepared with three different fiber post lengths and two different abutment heights, using both experimental and finite element (FE) approaches. Forty-eight human maxillary premolars with two roots were selected and endodontically treated. The teeth were randomly distributed into six equally sized groups (n = 8) with different combinations of post lengths (7.5, 11, and 15 mm) and abutment heights (3 and 5 mm). All the teeth restored with glass fiber post (Rely X Fiber Post, 3M ESPE, USA) and a full zirconia crown. All the specimens were thermocycled and then loaded to failure at an oblique angle of 135°. Statistical analysis was performed for the effects of post length and abutment height on failure loads using ANOVA and Tukey's honestly significant difference test. In addition, corresponding FE models of a premolar restored with a glass fiber post were developed to examine mechanical responses. The factor of post length (P < 0.01) had a significant effect on failure load. The abutment height (P > 0.05) did not have a significant effect on failure load. The highest mean fracture resistance was recorded for the 15 mm post length and 5 mm abutment height test group, which was significantly more resistant to fracture than the 7.5 mm post and 5 mm abutment height group (P < 0.05). The FE analysis showed the peak compression and tension stress values of 7.5 mm post length were higher than that of 11 and 15 mm post length. The stress value of remaining tooth decreased as the post length was increased. Within the limitations of this experimental and FE analysis study, increasing the post length inside the root of endodontically treated premolar teeth restored with glass-fiber posts increase the fracture resistance to non-axial forces. Failure mode is more favorable with reduced abutment heights.

Predictive value of cervical length measurement and fibronectin testing in threatened preterm labor.

PubMed

van Baaren, Gert-Jan; Vis, Jolande Y; Wilms, Femke F; Oudijk, Martijn A; Kwee, Anneke; Porath, Martina M; Oei, Guid; Scheepers, Hubertina C J; Spaanderman, Marc E A; Bloemenkamp, Kitty W M; Haak, Monique C; Bolte, Antoinette C; Bax, Caroline J; Cornette, Jérôme M J; Duvekot, Johannes J; Nij Bijvanck, Bas W A; van Eyck, Jim; Franssen, Maureen T M; Sollie, Krystyna M; Vandenbussche, Frank P H A; Woiski, Mallory; Grobman, William A; van der Post, Joris A M; Bossuyt, Patrick M M; Opmeer, Brent C; Mol, Ben W J

2014-06-01

To estimate the performance of combining cervical length measurement with fetal fibronectin testing in predicting delivery in women with symptoms of preterm labor. We conducted a prospective nationwide cohort study in all 10 perinatal centers in The Netherlands. Women with symptoms of preterm labor between 24 and 34 weeks of gestation with intact membranes were included. In all women, qualitative fibronectin testing (0.050-microgram/mL cutoff) and cervical length measurement were performed. Logistic regression was used to predict spontaneous preterm delivery within 7 days after testing. A risk less than 5%, corresponding to the risk for women with a cervical length of at least 25 mm, was considered as low risk. Between December 2009 and August 2012, 714 women were enrolled. Fibronectin results and cervical length were available for 665 women, of whom 80 (12%) delivered within 7 days. Women with a cervical length of at least 30 mm or with a cervical length between 15 and 30 mm with a negative fibronectin result were at low risk (less than 5%) of spontaneous delivery within 7 days. Fibronectin testing in case of a cervical length between 15 and 30 mm additionally classified 103 women (15% of the cohort) as low risk and 36 women (5% of the cohort) as high risk. Cervical length measurement, combined with fetal fibronectin testing in case of a cervical length between 15 and 30 mm, improves identification of women with a low risk to deliver spontaneously within 7 days. II.

Age, growth, mortality and reproductive seasonality of jolthead porgy, Calamus bajonado, from Florida waters.

PubMed

Burton, Michael L; Potts, Jennifer C; Page, Jordan; Poholek, Ariel

2017-01-01

Ages of jolthead porgy ( Calamus bajonado Schneider 1801) ( n  = 635) from Florida commercial and recreational fisheries from 2008-2016 were determined using sectioned sagittal otoliths. We determined, using edge-type analysis, that opaque zones were annular, forming March-June (peaking in April). Jolthead porgy ranged from 1-13 years, and the largest fish measured 680 mm TL (total length, mm). Body size relationships for jolthead porgy were TL  = 1.09 FL  + 20.44 ( n  = 622, r 2  = 0.99), FL  = 0.90 TL -14.26 ( n  = 622, r 2  = 0.99), and W  = 1.1 × 10 -5 TL 3.06 ( n  = 577), where W is total weight (grams, g) and FL is fork length (mm). The von Bertalanffy growth equation for jolthead porgy was L t  = 737(1 -  e -0.14( t +2.02) ) ( n  = 635). Point estimate of natural mortality was M  = 0.32, while age-specific estimates of M ranged from 0.58-0.17 y -1 for ages 1-13. Catch curve analysis estimated the instantaneous rate of total mortality Z  = 0.70, while instantaneous rate of fishing mortality F was 0.38. Macroscopic staging of female gonads indicated the presence of hydrated oocytes from December-March, and GSI data indicates that peak spawning in females occurs during March. This study presents the first published findings of life history parameters for jolthead porgy from the Atlantic waters off the southeastern United States.

[The relationship between eyeball structure and visual acuity in high myopia].

PubMed

Liu, Yi-Chang; Xia, Wen-Tao; Zhu, Guang-You; Zhou, Xing-Tao; Fan, Li-Hua; Liu, Rui-Jue; Chen, Jie-Min

2010-06-01

To explore the relationship between eyeball structure and visual acuity in high myopia. Totally, 152 people (283 eyeballs) with different levels of myopia were tested for visual acuity, axial length, and fundus. All cases were classified according to diopter, axial length, and fundus. The relationships between diopter, axial length, fundus and visual acuity were studied. The mathematical models were established for visual acuity and eyeball structure markers. The visual acuity showed a moderate correlation with fundus class, comus, axial length and diopter ([r] > 0.4, P < 0.000 1). The visual acuity in people with the axial length longer than 30.00 mm, diopter above -20.00 D and fundus in 4th class were mostly below 0.5. The mathematical models were established by visual acuity and eyeball structure markers. The visual acuity should decline with axial length extension, diopter deepening and pathological deterioration of fundus. To detect the structure changes by combining different kinds of objective methods can help to assess and to judge the vision in high myopia.

Prediction of advanced endovascular stent graft rotation and its associated morbidity and mortality.

PubMed

Crawford, Sean A; Sanford, Ryan M; Doyle, Matthew G; Wheatcroft, Mark; Amon, Cristina H; Forbes, Thomas L

2018-01-29

Advanced endovascular aneurysm repair (EVAR) with fenestrated and branched stent grafts is increasingly being used to repair complex aortic aneurysms; however, these devices can rotate unpredictably during deployment, leading to device misalignment. The objectives of this study were to quantify the short-term clinical outcomes in patients with intraoperative stent graft rotation and to identify quantitative anatomic markers of the arterial geometry that can predict stent graft rotation preoperatively. A prospective study evaluating all patients undergoing advanced EVAR was conducted at two university-affiliated hospitals between November 2015 and December 2016. Stent graft rotation (defined as ≥10 degrees) was measured on intraoperative fluoroscopic video of the deployment sequence. Standard preoperative computed tomography angiography imaging was used to calculate the geometric properties of the arterial anatomy. Any in-hospital and 30-day complications were prospectively documented, and a composite outcome of any end-organ ischemia or death was used as the primary end point. Thirty-nine patients undergoing advanced EVAR were enrolled in the study with a mean age of 75 years (interquartile range [IQR], 71-80 years) and a mean aneurysm diameter of 64 mm (IQR, 59-65 mm). The incidence of stent graft rotation was 37% (n = 14), with a mean rotation of 25 degrees (IQR, 21-28 degrees). A nominal logistic regression model identified iliac artery torsion, volume of iliac artery calcification, and stent graft length as the primary predictive factors. The total net torsion and the total volume of calcific plaque were higher in patients with stent graft rotation, 8.9 ± 0.8 mm -1 vs 4.1 ± 0.5 mm -1 (P < .0001) and 1054 ± 144 mm 3 vs 525 ± 83 mm 3 (P < .01), respectively. The length of the implanted stent grafts was also higher in patients with intraoperative rotation, 172 ± 9 mm vs 156 ± 8 mm (P < .01). The composite outcome of any end-organ ischemia or death was also substantially higher in patients with stent graft rotation (36% vs 0%; P = .004). In addition, patients with stent graft rotation had significantly higher combined rates of type Ib and type III endoleaks (43% vs 8%; P = .03). Patients with intraoperative stent graft rotation have a significantly higher rate of severe postoperative complications, and this is strongly associated with higher levels of iliac artery torsion, calcification, and stent graft length. These findings suggest that preoperative quantitative analysis of iliac artery torsion and calcification may improve risk stratification of patients before advanced EVAR. Copyright © 2017 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

Fluoroscopy-Guided Percutaneous Vertebral Body Biopsy Using a Novel Drill-Powered Device: Technical Case Series

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallace, Adam N., E-mail: wallacea@mir.wustl.edu; Pacheco, Rafael A., E-mail: pachecor@mir.wustl.edu; Tomasian, Anderanik, E-mail: tomasiana@mir.wustl.edu

2016-02-15

BackgroundA novel coaxial biopsy system powered by a handheld drill has recently been introduced for percutaneous bone biopsy. This technical note describes our initial experience performing fluoroscopy-guided vertebral body biopsies with this system, compares the yield of drill-assisted biopsy specimens with those obtained using a manual technique, and assesses the histologic adequacy of specimens obtained with drill assistance.MethodsMedical records of all single-level, fluoroscopy-guided vertebral body biopsies were reviewed. Procedural complications were documented according to the Society of Interventional Radiology classification. The total length of bone core obtained from drill-assisted biopsies was compared with that of matched manual biopsies. Pathology reportsmore » were reviewed to determine the histologic adequacy of specimens obtained with drill assistance.ResultsTwenty eight drill-assisted percutaneous vertebral body biopsies met study inclusion criteria. No acute complications were reported. Of the 86 % (24/28) of patients with clinical follow-up, no delayed complications were reported (median follow-up, 28 weeks; range 5–115 weeks). The median total length of bone core obtained from drill-assisted biopsies was 28 mm (range 8–120 mm). This was longer than that obtained from manual biopsies (median, 20 mm; range 5–45 mm; P = 0.03). Crush artifact was present in 11 % (3/28) of drill-assisted biopsy specimens, which in one case (3.6 %; 1/28) precluded definitive diagnosis.ConclusionsA drill-assisted, coaxial biopsy system can be used to safely obtain vertebral body core specimens under fluoroscopic guidance. The higher bone core yield obtained with drill assistance may be offset by the presence of crush artifact.« less

Reproduction and early-life accommodations of landlocked alewives to a southern range extension

USGS Publications Warehouse

Nigro, A.A.; Ney, John J.

1982-01-01

Reproduction and first-year growth and food habits of landlocked alewives Alosa pseudoharengus in Claytor Lake, Virginia were examined and compared to descriptions for populations in the species' established New England-Great Lakes range. Alewives in mesothermal (2–27 C) Claytor Lake are shorter-lived (3 years) but grow faster, mature earlier (age 1), and have higher relative and absolute fecundities than have been reported for populations in colder northern waters. The 1979 spawning period extended from early May to early August, beginning at least 1 month earlier and lasting 4–9 weeks longer than in northern lakes. Changes in ovary condition during the spawning period suggest that alewives may be fractional spawners. Evidence of spawning was found in littoral areas throughout the lower 15 km of the reservoir. Growth in length of age-0 Claytor Lake alewives was linear through September and terminated in late autumn. Total first-year growth was reduced in 1979 (maximum of 130 mm total length, TL) from previous years (average of 160 mm TL), although it was substantially greater than recorded in the Great Lakes and the northeastern United States. The longer growing season, rather than accelerated in-season growth, appears to account for larger size achieved in Claytor Lake. High annual growth limits predation by Claytor Lake game fish on early spawned age-0 alewives by late summer. As elsewhere, larval and juvenile alewives (6–70 mm TL) fed primarily on copepods and cladocerans. Age-0 alewives longer than 35 mm TL demonstrated positive size-selection for cyclopoid copepods comparable to that shown by adults. Our findings suggest that self-sustaining alewife populations can be established in many inland waters but raise concerns regarding their forage value and community impacts.

Claw length recommendations for dairy cow foot trimming

PubMed Central

Archer, S. C.; Newsome, R.; Dibble, H.; Sturrock, C. J.; Chagunda, M. G. G.; Mason, C. S.; Huxley, J. N.

2015-01-01

The aim was to describe variation in length of the dorsal hoof wall in contact with the dermis for cows on a single farm, and hence, derive minimum appropriate claw lengths for routine foot trimming. The hind feet of 68 Holstein-Friesian dairy cows were collected post mortem, and the internal structures were visualised using x-ray µCT. The internal distance from the proximal limit of the wall horn to the distal tip of the dermis was measured from cross-sectional sagittal images. A constant was added to allow for a minimum sole thickness of 5 mm and an average wall thickness of 8 mm. Data were evaluated using descriptive statistics and two-level linear regression models with claw nested within cow. Based on 219 claws, the recommended dorsal wall length from the proximal limit of hoof horn was up to 90 mm for 96 per cent of claws, and the median value was 83 mm. Dorsal wall length increased by 1 mm per year of age, yet 85 per cent of the null model variance remained unexplained. Overtrimming can have severe consequences; the authors propose that the minimum recommended claw length stated in training materials for all Holstein-Friesian cows should be increased to 90 mm. PMID:26220848

Age and growth of round gobies in Lake Michigan, with preliminary mortality estimation

USGS Publications Warehouse

Huo, Bin; Madenjian, Charles P.; Xie, Cong X.; Zhao, Yingming; O'Brien, Timothy P.; Czesny, Sergiusz J.

2015-01-01

The round goby (Neogobius melanostomus) is a prevalent invasive species throughout Lake Michigan, as well as other Laurentian Great Lakes, yet little information is available on spatial variation in round goby growth within one body of water. Age and growth of round goby at three areas of Lake Michigan were studied by otolith analysis from a sample of 659 specimens collected from 2008 to 2012. Total length (TL) ranged from 48 to 131 mm for Sturgeon Bay, from 50 to 125 mm for Waukegan, and from 54 to 129 mm for Sleeping Bear Dunes. Ages ranged from 2 to 7 years for Sturgeon Bay, from 2 to 5 years for Waukegan, and from 2 to 6 years for Sleeping Bear Dunes. Area-specific and sex-specific body–otolith relationships were used to back-calculate estimates of total length at age, which were fitted to von Bertalanffy models to estimate growth rates. For both sexes, round gobies at Sleeping Bear Dunes and Waukegan grew significantly faster than those at Sturgeon Bay. However, round goby growth did not significantly differ between Sleeping Bear Dunes and Waukegan for either sex. At all three areas of Lake Michigan, males grew significantly faster than females. Based on catch curve analysis, estimates of annual mortality rates ranged from 0.79 to 0.84. These relatively high mortality rates suggested that round gobies may be under predatory control in Lake Michigan.

Life history variation among four lake trout morphs at Isle Royale, Lake Superior

USGS Publications Warehouse

Hansen, Michael J.; Nate, Nancy A.; Muir, Andrew M.; Bronte, Charles R.; Zimmerman, Mara S.; Krueger, Charles C.

2016-01-01

Life history traits were compared among four morphs of lake trout at Isle Royale, Lake Superior. Of 738 lake trout caught at Isle Royale, 701 were assigned to a morph (119 humpers, 160 leans, 85 redfins, and 337 siscowets) using a combination of statistical analysis of head and body shape and visual assignment. On average, redfins were longer (544 mm), heavier (1,481 g), heavier at length (Wr = 94), more buoyant, and older (22 years) than siscowets (519 mm; 1,221 g; 90; 19 years), leans (479 mm; 854 g; 82; 13 years), and humpers (443 mm; 697 g; 87; 17 years). On average, leans grew from a younger age at length = 0 and shorter length at age = 0, at a faster early growth rate to a longer asymptotic length than the other three morphs, while redfins grew at a slower instantaneous rate and humpers grew to a shorter asymptotic length than other morphs. On average, leans were longer (562 mm) and older (15 years) at 50% maturity than redfins (427 mm, 12 years), siscowets (401 mm, 11 years), or humpers (394 mm, 13 years). Life history parameters did not differ between males and females within each morph. We conclude that differences in life history attributes of lean, humper, redfin, and siscowet morphs of lake trout are consistent with differential habitat use in waters around Isle Royale, Lake Superior.

Measuring anterior loop length of the inferior alveolar nerve to estimate safe zone in implant planning: A CBCT study in a Malaysian population.

PubMed

Wong, Shi Kang; Patil, Pravinkumar G

2018-03-15

The inferior alveolar nerve (IAN) frequently loops backward before exiting from the mental foramen and spreads several millimeters medially to the foramen. Implant placement in this area may damage the nerve if the anterior loop area is not carefully identified in a radiographic or computed tomography (CT) evaluation. The purpose of this observational study was to measure the prevalence of the presence of the anterior loop and to estimate sex and ethnicity-related variations in anterior loop length in the Malaysian population. A total of 100 cone beam computed tomography (CBCT) Digital Imaging and Communications in Medicine (DICOM) files were selected from a pool of 810 ongoing or completed patients in 3 different ethnic groups: Malay (33), Indian (33), and Chinese (34). The DICOM data were imported into commercial software. The IAN was traced with software along with the anterior loop and part of the incisive nerve. The vertical length of the nerve was estimated from the canal to the opening of the mental foramen from the cross-sectional view and translated to the panoramic view. Measurement was made from this point to the most anterior point of the anterior loop by following the trajectory of the nerve and was repeated on the opposite side. A 2-way mixed analysis of variance (ANOVA) test was carried out to evaluate the sex- and ethnicity-related variations (α=.05). The anterior loop was present in 94% of the 100 participants. Overall anterior loop length (AnLL) ranged between 0.73 and 7.99 mm with a mean length of 3.69 ±1.75 mm on the left side and 3.85 ±1.73 mm on the right side. Among all participants, no statistically significant differences were found between the left and right sides of the mandible (P=.379). Overall, no significant main effect of ethnicity (P=.869) or sex (P=.576) was found on AnLL measurements. Also, with multiple comparisons, no significant effect was found between each pair of ethnic groups. Men in all 3 ethnic groups had greater AnLL than women. The anterior loop was present in 94% of the 100 participants among the 3 major ethnic groups of Malaysia. Overall AnLL ranged between 0.73 and 7.99 mm and mean lengths of 3.69 ±1.75 mm on the left side and 3.85 ±1.73 mm on the right side, with no significant ethnicity- or sex-related variations. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

The role of skin biopsy in differentiating small-fiber neuropathy from ganglionopathy.

PubMed

Provitera, V; Gibbons, C H; Wendelschafer-Crabb, G; Donadio, V; Vitale, D F; Loavenbruck, A; Stancanelli, A; Caporaso, G; Liguori, R; Wang, N; Santoro, L; Kennedy, W R; Nolano, M

2018-06-01

We aimed to test the clinical utility of the leg:thigh intraepidermal nerve-fiber (IENF) density ratio as a parameter to discriminate between length-dependent small-fiber neuropathy (SFN) and small-fiber sensory ganglionopathy (SFSG) in subjects with signs and symptoms of small-fiber pathology. We retrospectively evaluated thigh and leg IENF density in 314 subjects with small-fiber pathology (173 with distal symmetrical length-dependent SFN and 141 with non-length-dependent SFSG). A group of 288 healthy subjects was included as a control group. The leg:thigh IENF density ratio was calculated for all subjects. We used receiver operating characteristic curve analyses to assess the ability of this parameter to discriminate between length-dependent SFN and SFSG, and the decision curve analysis to estimate its net clinical benefit. In patients with neuropathy, the mean IENF density was 14.8 ± 6.8/mm at the thigh (14.0 ± 6.9/mm in length-dependent SFN and 15.9 ± 6.7/mm in patients with SFSG) and 7.5 ± 4.5/mm at the distal leg (5.4 ± 3.2/mm in patients with length-dependent SFN and 10.1 ± 4.6/mm in patients with SFSG). The leg:thigh IENF density ratio was significantly (P < 0.01) lower in patients with length-dependent SFN (0.44 ± 0.23) compared with patients with SFSG (0.68 ± 0.28). The area under the curve of the receiver operating characteristic analysis to discriminate between patients with length-dependent SFN and SFSG was 0.79. The decision curve analysis demonstrated the clinical utility of this parameter. The leg:thigh IENF ratio represents a valuable tool in the differential diagnosis between SFSG and length-dependent SFN. © 2018 EAN.

Computer guided restoration of joint line and femoral offset in cruciate substituting total knee arthroplasty.

PubMed

Shetty, Gautam M; Mullaji, Arun; Bhayde, Sagar

2012-10-01

This prospective study aimed to evaluate radiographically, change in joint line and femoral condylar offset with the optimized gap balancing technique in computer-assisted, primary, cruciate-substituting total knee arthroplasties (TKAs). One hundred and twenty-nine consecutive computer-assisted TKAs were evaluated radiographically using pre- and postoperative full-length standing hip-to-ankle, antero-posterior and lateral radiographs to assess change in knee deformity, joint line height and posterior condylar offset. In 49% of knees, there was a net decrease (mean 2.2mm, range 0.2-8.4mm) in joint line height postoperatively whereas 46.5% of knees had a net increase in joint line height (mean 2.5mm, range 0.2-11.2mm). In 93% of the knees, joint line was restored to within ± 5 mm of preoperative values. In 53% of knees, there was a net increase (mean 2.9 mm, range 0.2-12 mm) in posterior offset postoperatively whereas 40% of knees had a net decrease in posterior offset (mean 4.2mm, range 0.6-20mm). In 82% of knees, the posterior offset was restored within ± 5 mm of preoperative values. Based on radiographic evaluation in extension and at 30° flexion, the current study clearly demonstrates that joint line and posterior femoral condylar offset can be restored in the majority of computer-assisted, cruciate-substituting TKAs to within 5mm of their preoperative value. The optimized gap balancing feature of the computer software allows the surgeon to simulate the effect of simultaneously adjusting femoral component size, position and distal femoral resection level on joint line and posterior femoral offset. Copyright © 2011 Elsevier B.V. All rights reserved.

Evidence that lake trout served as a buffer against sea lamprey predation on burbot in Lake Erie

USGS Publications Warehouse

Stapanian, M.A.; Madenjian, C.P.

2007-01-01

The population of burbot Lota lota in Lake Erie recovered during 1986–2003, mainly because of the control of sea lamprey Petromyzon marinus, which began in 1986. Burbot populations continued to grow during 1996–1998, when sea lamprey control was substantially reduced. We calculated mortality parameters for burbot in Lake Erie by estimating age at capture for 2,793 burbot caught in annual gill-net surveys of eastern Lake Erie from 1994 to 2003. Based on catch-curve analysis, annual mortality in Lake Erie during 1994–2003 was estimated as 33%. Annual mortality of the 1992 year-class of burbot was estimated as 30%. The mortality of burbot during the years of reduced sea lamprey control was not different from that during the 3 years preceding reduced control and was significantly lower than that during the entire portion of the time series in which full sea lamprey control was conducted. These results suggest that the reduction in sea lamprey control did not lead to increased burbot mortality. The catch per gill-net lift of large burbot (total length > 600 mm), the size preferred by sea lampreys, was lower than that of adult lake trout Salvelinus namaycush (age 5 and older; total length > 700 mm) before lampricide application was reduced. Although adult lake trout populations declined, the abundance of large burbot did not change during the period of reduced lampricide application. These results support a hypothesis that a healthy population of adult lake trout can serve as a buffer species, acting to reduce predation of burbot by sea lampreys when sea lamprey populations increase. Burbot attained sexual maturity at a relatively early age (3 or 4 years) and a total length (approximately 500 mm) that was smaller than the preferred prey size for sea lampreys. These characteristics and the buffering effect of the lake trout population enabled growth of the burbot population during the brief period when lamprey control was reduced.

Range and movement of resident holdover and hatchery brown trout tagged with radio transmitters in the Farmington River, Connecticut

USGS Publications Warehouse

Popoff, N.D.; Neumann, Robert M.

2005-01-01

The 5.8-km West Branch Farmington River Trout Management Area (TMA) is one of Connecticut's premier catch-and-release fisheries for brown trout Salmo trutta. However, little is known about the behavior of brown trout in this system and to what extent brown trout emigrate from the TMA. The objectives of this study were to determine the movement, range, and emigration of resident holdover and newly stocked brown trout tagged with radio transmitters in the TMA. Transmitters were implanted into 22 first-year (mean total length = 314 mm) and 25 second-year (mean total length = 432 mm) holdover brown trout. Twenty catchable-size (mean total length = 290 mm) brown trout were also implanted with transmitters and released into the TMA. The mean range (distance between the extreme upstream and downstream locations) was greater for second-year holdover brown trout than for first-year holdover brown trout, and it was greater in fall than in winter. The movement (distance moved between successive locations) of holdover brown trout was greater in fall than in winter. Movement of first-year holdover brown trout was significantly related to discharge, water temperature, and the number of days between successive locations. Newly stocked brown trout exhibited the two largest ranges (5.3 and 4.7 km). The range of newly stocked brown trout was not different between seasons, but movement was greater in spring than in summer. Through 16 weeks poststocking, there was no discernable difference in the percentage of stocked brown trout dispersing in a predominantly upstream or downstream direction. Mean dispersal distances from the stocking location were 0.5 and 0.9 km at 2 and 12 weeks poststocking, respectively. Movement of newly stocked brown trout was positively related to discharge and negatively related to water temperature. A known 6% (4 of 67) of the tagged brown trout emigrated from the TMA, but up to 21% (14 of 67) of tagged fish could have left the study area if all missing fish were emigrants. ?? Copyright by the American Fisheries Society 2005.

Three new and a known species of the genus Proleptonchus Lordello, 1955 (Nematoda: Leptonchidae) with a diagnostic compendium of the genus.

PubMed

Ahad, Sumaya; Ahmad, Wasim

2016-11-09

This paper deals with the description of three new and one known species of the genus Proleptonchus Lordello, 1955. Proleptonchus kazirangus n. sp. from Kaziranga National Park, India is characterized by having 1.08-1.45 mm long body; cap-like, offset, lip region; 7-8 µm long odontostyle and 10-12 µm long odontophore; short, pear-shaped pharyngeal bulb offset by a constriction, occupying about 18-21% of total neck length; female genital system mono-prodelphic; pars dilatata uteri with distinctly sclerotized central lumen containing refringent apophyses; posterior uterine sac 78-112 µm long, with sac-like structure representing a rudimentary oviduct; transverse vulva, short, rounded-conoid tail and males with 31-33 µm long spicules, lateral guiding pieces and seven, regularly spaced ventromedian supplements. P. prerectus n. sp. from Japan is characterized by having 1.18-1.43 mm long body; lip region cap-like, offset by a slight constriction; odontostyle 8 µm, odontophore 9-10 µm; short cylindroid basal bulb offset by a constriction, occupying about 16-20% of total neck length; female genital system mono-prodelphic; pars dilatata uteri with sclerotized refringent apophyses; posterior uterine sac small, 27-36 µm; transverse vulva; a prerectal chamber and short, rounded-hemispheroid tail. P. japonicus n. sp. also from Japan is characterized by having 0.91-1.04 mm long body; lip region cap-like, set off by a slight constriction; odontostyle 5 µm and odontophore 10-11 µm long; pharynx consists of a very slender, non-muscular anterior part, separated from pyriform basal bulb by a constriction, with thickened lumen in posterior region, occupying about 18-20% of total neck length; female genital system mono-prodelphic; posterior uterine sac small, 20-24 µm long; transverse vulva and short, rounded-conoid tail. P. shamimi Bajaj & Bhatti, 1980 is redescribed and its relationship with closely related species is discussed. A diagnostic compendium of all the valid species of Proleptonchus is also provided.

Adaptation of the length-active tension relationship in rabbit detrusor

PubMed Central

Almasri, Atheer M.; Bhatia, Hersch; Klausner, Adam P.; Ratz, Paul H.

2009-01-01

Studies have shown that the length-tension (L-T) relationships in airway and vascular smooth muscles are dynamic and can adapt to length changes over a period of time. Our prior studies have shown that the passive L-T relationship in rabbit detrusor smooth muscle (DSM) is also dynamic and that DSM exhibits adjustable passive stiffness (APS) characterized by a passive L-T curve that can shift along the length axis as a function of strain history and activation history. The present study demonstrates that the active L-T curve for DSM is also dynamic and that the peak active tension produced at a particular muscle length is a function of both strain and activation history. More specifically, this study reveals that the active L-T relationship, or curve, does not have a unique peak tension value with a single ascending and descending limb, but instead reveals that multiple ascending and descending limbs can be exhibited in the same DSM strip. This study also demonstrates that for DSM strips not stretched far enough to reveal a descending limb, the peak active tension produced by a maximal KCl-induced contraction at a short, passively slack muscle length of 3 mm was reduced by 58.6 ± 4.1% (n = 15) following stretches to and contractions at threefold the original muscle length, 9 mm. Moreover, five subsequent contractions at the short muscle length displayed increasingly greater tension; active tension produced by the sixth contraction was 91.5 ± 9.1% of that produced by the prestretch contraction at that length. Together, these findings indicate for the first time that DSM exhibits length adaptation, similar to vascular and airway smooth muscles. In addition, our findings demonstrate that preconditioning, APS and adaptation of the active L-T curve can each impact the maximum total tension observed at a particular DSM length. PMID:19675182

Compact and high resolution virtual mouse using lens array and light sensor

NASA Astrophysics Data System (ADS)

Qin, Zong; Chang, Yu-Cheng; Su, Yu-Jie; Huang, Yi-Pai; Shieh, Han-Ping David

2016-06-01

Virtual mouse based on IR source, lens array and light sensor was designed and implemented. Optical architecture including lens amount, lens pitch, baseline length, sensor length, lens-sensor gap, focal length etc. was carefully designed to achieve low detective error, high resolution, and simultaneously, compact system volume. System volume is 3.1mm (thickness) × 4.5mm (length) × 2, which is much smaller than that of camera-based device. Relative detective error of 0.41mm and minimum resolution of 26ppi were verified in experiments, so that it can replace conventional touchpad/touchscreen. If system thickness is eased to 20mm, resolution higher than 200ppi can be achieved to replace real mouse.

A scalable, micropore, platelet rich plasma separation device.

PubMed

Dickson, Mary Nora; Amar, Levy; Hill, Michael; Schwartz, Joseph; Leonard, Edward F

2012-12-01

We have designed a novel, low energy platelet-rich-plasma (PRP) separator capable of producing 50 mL of PRP in 30 min, intended for military and emergency applications. Blood flows over a 3 mm length of sieve at high rates of shear. A plasma-platelet filtrate passes through the sieve's pores while erythrocytes remain. The filtrate is flowed over a second 3 mm length of smaller-pored sieve that withdraws plasma. Bulk blood volume is maintained by returning platelet-free plasma to the erythrocyte pool, enabling a nearly complete multi-pass platelet extraction. The total percentage of platelets extracted is:θ(T)=1-exp (-V(f)(T)Φ(P)/V) where V is the original plasma volume, V ( f )(T) is the total filtered volume, and ϕ ( P ) is platelet passage ratio (filtrate concentration/bulk average concentration) taken to be constant. Maximum θ(T) occurs at maximum V ( f )(T)× ϕ ( P ) Test microsieves, 3 mm long × 3 mm wide, were used. ϕ ( P ) values measured at various filtrate flow rates (20-100 uL/min) and utilizing various filter pore sizes (1.2-3.5 μm), was as high as 150 %. Maximum V ( f )(T)× ϕ ( P ) was achieved utilizing the 3.5 um filters at the highest flow rate, 100 uL/min. Erythrocyte leakages were always below 2,000/uL, far below the allowable limit stipulated by the American Association of Blood Banking. These data imply that a 13.7 cm(2) filter area is sufficient to achieve the target separation of 50 mL of platelet concentrate in 30 min. The filtration cartridge would consist of multiple microporous strips of 3 mm width arranged in parallel so that each element would see the conditions used in the prototype experiments presented here. Other microfiltration schemes suggest no method of scaling to practical levels.

[Root system distribution and biomechanical characteristics of Bambusa oldhami].

PubMed

Zhou, Ben-Zhi; Xu, Sheng-Hua; An, Yan-Fei; Xu, Sheng-Hua

2014-05-01

To determine the mechanism of soil stabilizing through Bambusa oldhami root system, the vertical distribution of B. oldhami root system in soil was investigated, and the tensile strength of individual root and soil shear strength were measured in B. oldhami forest. The dry mass, length, surface area and volume of the B. oldhami root system decreased with the increasing soil depth, with more than 90% of the root system occurring in the 0-40 cm soil layer. The root class with D 1 mm occupied the highest percentage of the total in terms of root length, accounting for 79.6%, but the lowest percentage of the total in terms of root volume, accounting for 8.2%. The root class with D >2 mm was the opposite, and the root class with D= 1-2 mm stayed in between. The maximum tensile resistance of B. oldhami root, either with 12% moisture content or a saturated moisture content, increased with the increasing root diameter, while the tensile strength decreased with the increasing root diameter in accordance with power function. Tensile strength of the root, with either of the two moisture contents, was significantly different among the diameter classes, with the highest tensile strength occurring in the root with D < or = 1 mm and the lowest in the root with D > or = 2 mm. The tensile strength of root with 12% moisture content was significantly higher than that with the saturated moisture content, and less effect of moisture content on root tensile strength would occur in thicker roots. The shear strengths of B. oldhami forest soil and of bare soil both increased with the increasing soil depth. The shear strength of B. oldhami forest soil had a linear positive correlation with the root content in soil, and was significantly higher than that of bare soil. The shear strength increment in B. oldhami forest was positively correlated with the root content in soil according to an exponential function, but not related significantly with soil depth.

Short dental implants versus standard dental implants placed in the posterior jaws: A systematic review and meta-analysis.

PubMed

Lemos, Cleidiel Aparecido Araujo; Ferro-Alves, Marcio Luiz; Okamoto, Roberta; Mendonça, Marcos Rogério; Pellizzer, Eduardo Piza

2016-04-01

The purpose of the present systematic review and meta-analysis was to compare short implants (equal or less than 8mm) versus standard implants (larger than 8mm) placed in posterior regions of maxilla and mandible, evaluating survival rates of implants, marginal bone loss, complications and prosthesis failures. This review has been registered at PROSPERO under the number CRD42015016588. Main search terms were used in combination: dental implant, short implant, short dental implants, short dental implants posterior, short dental implants maxilla, and short dental implants mandible. An electronic search for data published up until September/2015 was undertaken using the PubMed/Medline, Embase and The Cochrane Library databases. Eligibility criteria included clinical human studies, randomized controlled trials and/or prospective studies, which evaluated short implants in comparison to standard implants in the same study. The search identified 1460 references, after inclusion criteria 13 studies were assessed for eligibility. A total of 1269 patients, who had received a total of 2631 dental implants. The results showed that there was no significant difference of implants survival (P=.24; RR:1.35; CI: 0.82-2.22), marginal bone loss (P=.06; MD: -0.20; CI: -0.41 to 0.00), complications (P=.08; RR:0.54; CI: 0.27-1.09) and prosthesis failures (P=.92; RR:0.96; CI: 0.44-2.09). Short implants are considered a predictable treatment for posterior jaws. However, short implants with length less than 8 mm (4-7 mm) should be used with caution because they present greater risks to failures compared to standard implants. Short implants are frequently placed in the posterior area in order to avoid complementary surgical procedures. However, clinicians need to be aware that short implants with length less than 8mm present greater risk of failures. Copyright © 2016. Published by Elsevier Ltd.

46 CFR 164.009-17 - Density measurement.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) If the sample is a solid material, a specimen that has a length of 305 mm, a width of 305 mm, and thickness equal to that of the sample is prepared. The length and width are measured to the nearest 0.80 mm and the thickness to the nearest 0.25 mm. Allowance is made for any irregularity in the surfaces of...

46 CFR 164.009-17 - Density measurement.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) If the sample is a solid material, a specimen that has a length of 305 mm, a width of 305 mm, and thickness equal to that of the sample is prepared. The length and width are measured to the nearest 0.80 mm and the thickness to the nearest 0.25 mm. Allowance is made for any irregularity in the surfaces of...

46 CFR 164.009-17 - Density measurement.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) If the sample is a solid material, a specimen that has a length of 305 mm, a width of 305 mm, and thickness equal to that of the sample is prepared. The length and width are measured to the nearest 0.80 mm and the thickness to the nearest 0.25 mm. Allowance is made for any irregularity in the surfaces of...

46 CFR 164.009-17 - Density measurement.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) If the sample is a solid material, a specimen that has a length of 305 mm, a width of 305 mm, and thickness equal to that of the sample is prepared. The length and width are measured to the nearest 0.80 mm and the thickness to the nearest 0.25 mm. Allowance is made for any irregularity in the surfaces of...

Radiographic screen-film noise power spectrum: variation with microdensitometer slit length.

PubMed

Sandrik, J M; Wagner, R F

1981-08-15

When the noise power spectrum (NPS) of a radiographic screen-film system is measured by microdensito-metrically scanning the film with a long narrow slit, sufficient slit length allows estimation of a section of the 2-D NPS from the 1-D film scans; insufficient length causes underestimation of the NPS, particularly at low frequencies ( greater, similar1 cycle/mm). Spectra of Hi-Plus, Par Speed, and Detail screens used with XRP films measured as a function of microdensitometer slit length tended to plateau at long slit lengths. The slit length was considered sufficient when NPS components at 0.4 cycle/mm were within 5% of the plateau. This occurred for slit lengths of at least 4.2, 2.6, and 2.5 mm for Hi-Plus, Par Speed, and Detail systems, respectively.

Anatomic study on mental canal and incisive nerve canal in interforaminal region in Chinese population.

PubMed

Xu, Yun; Suo, Ning; Tian, Xiufen; Li, Fei; Zhong, Guangxin; Liu, Xiaoran; Bao, Yongxing; Song, Tao; Tian, Hua

2015-08-01

This study was aimed to detect the positions of mental canal and incisive nerve canal as well as the prolongation of mandibular canal in interforaminal region in Chinese population to supply the reference data of the surgical safe zone in chin for clinicians. A total of 80 formalin-fixed semi-mandibles of Chinese adult cadavers were dissected, the positions and courses of mental canal and incisive nerve canal as well as the prolongation of mandibular canal in interforaminal region were measured. The mental foramina were present in all cases (100 %), and most of them were located below 2nd premolar (58.75 %). Accessory mental foramina were observed in 5 %. The anterior end of mandibular canal, extending along the course of 7.37 ± 1.10 mm above the lower border of mandible to interforaminal region about 3.54 ± 0.70 mm medial to the mental foramen, most often ended below between the two premolars (73.75 %), where it continued as the incisive nerve canal (100 %) and the mental canal (96.25 %). Mental canal, with the wall formed by compact bone, being 2.60 ± 0.60 mm in diameter and 4.01 ± 1.20 mm in length, opened into mental foramen. Incisive nerve canal, with the wall formed by thin compact bone and/or partly or completely by spongy bone, being 1.76 ± 0.27 mm in diameter and 24.87 ± 2.23 mm in length, extended to the incisor region along the course of 9.53 ± 1.43 mm above the lower border of mandible, and most often ended below the lateral incisor (70.00 %). This research recommended for chin operations in Chinese population: the surgical safe zone could be set in the region about over 4 mm anterior to the mental foramen, and over 12 mm above inferior border of mandible for anterior alveolar surgery, or within 9 mm above inferior border of mandible for genioplasty.

Demonstration of a real-time interferometer as a bunch-length monitor in a high-current electron beam accelerator.

PubMed

Thangaraj, J; Andonian, G; Thurman-Keup, R; Ruan, J; Johnson, A S; Lumpkin, A; Santucci, J; Maxwell, T; Murokh, A; Ruelas, M; Ovodenko, A

2012-04-01

A real-time interferometer (RTI) has been developed to monitor the bunch length of an electron beam in an accelerator. The RTI employs spatial autocorrelation, reflective optics, and a fast response pyro-detector array to obtain a real-time autocorrelation trace of the coherent radiation from an electron beam thus providing the possibility of online bunch-length diagnostics. A complete RTI system has been commissioned at the A0 photoinjector facility to measure sub-mm bunches at 13 MeV. Bunch length variation (FWHM) between 0.8 ps (~0.24 mm) and 1.5 ps (~0.45 mm) has been measured and compared with a Martin-Puplett interferometer and a streak camera. The comparisons show that RTI is a viable, complementary bunch length diagnostic for sub-mm electron bunches. © 2012 American Institute of Physics

Demonstration of a real-time interferometer as a bunch-length monitor in a high-current electron beam accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thangaraj, J.; Thurman-Keup, R.; Ruan, J.

2012-04-15

A real-time interferometer (RTI) has been developed to monitor the bunch length of an electron beam in an accelerator. The RTI employs spatial autocorrelation, reflective optics, and a fast response pyro-detector array to obtain a real-time autocorrelation trace of the coherent radiation from an electron beam thus providing the possibility of online bunch-length diagnostics. A complete RTI system has been commissioned at the A0 photoinjector facility to measure sub-mm bunches at 13 MeV. Bunch length variation (FWHM) between 0.8 ps ({approx}0.24 mm) and 1.5 ps ({approx}0.45 mm) has been measured and compared with a Martin-Puplett interferometer and a streak camera.more » The comparisons show that RTI is a viable, complementary bunch length diagnostic for sub-mm electron bunches.« less

Inherent length-scales of periodic solar wind number density structures

NASA Astrophysics Data System (ADS)

Viall, N. M.; Kepko, L.; Spence, H. E.

2008-07-01

We present an analysis of the radial length-scales of periodic solar wind number density structures. We converted 11 years (1995-2005) of solar wind number density data into radial length series segments and Fourier analyzed them to identify all spectral peaks with radial wavelengths between 72 (116) and 900 (900) Mm for slow (fast) wind intervals. Our window length for the spectral analysis was 9072 Mm, approximately equivalent to 7 (4) h of data for the slow (fast) solar wind. We required that spectral peaks pass both an amplitude test and a harmonic F-test at the 95% confidence level simultaneously. From the occurrence distributions of these spectral peaks for slow and fast wind, we find that periodic number density structures occur more often at certain radial length-scales than at others, and are consistently observed within each speed range over most of the 11-year interval. For the slow wind, those length-scales are L ˜ 73, 120, 136, and 180 Mm. For the fast wind, those length-scales are L ˜ 187, 270 and 400 Mm. The results argue for the existence of inherent radial length-scales in the solar wind number density.

Anatomical Assessment of the Temporopolar Artery for Revascularization of Deep Recipients.

PubMed

Tayebi Meybodi, Ali; Benet, Arnau; Griswold, Dylan; Dones, Flavia; Preul, Mark C; Lawton, Michael T

2018-05-30

Intracranial-intracranial and extracranial-intracranial bypass options for revascularization of deep cerebral recipients are limited and technically demanding. To assess the anatomical feasibility of using the temporopolar artery (TPA) for revascularization of the anterior cerebral artery (ACA), posterior cerebral artery (PCA), and superior cerebellar arteries (SCA). Orbitozygomatic craniotomy was performed bilaterally on 8 cadaveric heads. The cisternal segment of the TPA was dissected. The TPA was cut at M3-M4 junction with its proximal and distal calibers and the length of the cisternal segment measured. Feasibility of the TPA-A1-ACA, TPA-A2-ACA, TPA-SCA, and TPA-PCA bypasses were assessed. A total of 17 TPAs were identified in 16 specimens. The average distal TPA caliber was 1.0 ± 0.2 mm, and the average cisternal length was 37.5 ± 9.4 mm. TPA caliber was ≥ 1.0 mm in 12 specimens (70%). The TPA-A1-ACA bypass was feasible in all specimens, whereas the TPA reached the A2-ACA, SCA, and PCA in 94% of specimens (16/17). At the point of anastomosis, the average recipient caliber was 2.5 ± 0.5 mm for A1-ACA, and 2.3 ± 0.7 mm for A2-ACA. The calibers of the SCA and PCA at the anastomosis points were 2.0 ± 0.6 mm, and 2.7 ± 0.8 mm, respectively. The TPA-ACA, TPA-PCA, and TPA-SCA bypasses are anatomically feasible and may be used when the distal caliber of the TPA stump is optimal to provide adequate blood flow. This study lays foundations for clinical use of the TPA for ACA revascularization in well-selected cases.

Development of a miniaturized hour-glass shaped fatigue specimen

NASA Astrophysics Data System (ADS)

Miwa, Y.; Jitsukawa, S.; Hishinuma, A.

1998-10-01

Diametral strain-controlled push-pull fatigue tests with zero mean strain were carried out with miniaturized hour-glass shaped specimens of an austenitic stainless steel in solution annealed condition at room temperature. The specimens had a diameter of 1.25 mm at the minimum cross section and a total length of 25.4 mm. The number of cycles to failure ( Nf) was equal to or slightly greater than that obtained with standard size specimens. Nf was also revealed to be rather insensitive to the specimen load axis offset, indicating that the requirement of the specimen alignment to the load axis was not very severe for the miniaturized specimen.

A high speed CCSDS encoder for space applications

NASA Technical Reports Server (NTRS)

Whitaker, S.; Liu, K.

1990-01-01

This paper reports a VLSI implementation of the CCSDS standard Reed Solomon encoder circuit for the Space Station. The 1.0 micron double metal CMOS chip is 5.9 mm by 3.6 mm, contains 48,000 transistors, operates at a sustained data rate of 320 Mbits/s, and executes 2,560 Mops. The chip features a pin selectable interleave depth of 1 to 8. Block lengths of up to 255 bytes, as well as shortened codes, are supported. The control circuitry uses register cells which are immune to Single Event Upset. In addition, the CMOS process used is reported to be tolerant of over 1 Mrad total dose radiation.

Influence of rotational speed on the cyclic fatigue of rotary nickel-titanium endodontic instruments.

PubMed

Lopes, Hélio P; Ferreira, Alessandra A P; Elias, Carlos N; Moreira, Edson J L; de Oliveira, Júlio C Machado; Siqueira, José F

2009-07-01

During the preparation of curved canals, rotary nickel-titanium (NiTi) instruments are subjected to cyclic fatigue, which can lead to instrument fracture. Although several factors may influence the cyclic fatigue resistance of instruments, the role of the rotational speed remains uncertain. This study was intended to evaluate the effects of rotational speed on the number of cycles to fracture of rotary NiTi instruments. ProTaper Universal instruments F3 and F4 (Maillefer SA, Ballaigues, Switzerland) were used in an artificial curved canal under rotational speeds of 300 rpm or 600 rpm. The artificial canal was made of stainless steel, with an inner diameter of 1.5 mm, total length of 20 mm, and arc at the end with a curvature radius of 6 mm. The arc length was 9.4 mm and 10.6 mm on the straight part. The number of cycles required to fracture was recorded. Fractured surfaces and the helical shafts of the fractured instruments were analyzed by scanning electron microscopy. The results showed approximately a 30% reduction in the observed number of cycles to fracture as rotational speed was increased from 300 to 600 RPM (p < 0.05). The morphology of the fractured surface was always of ductile type, and no plastic deformation was observed on the helical shaft of fractured instruments. The present findings for both F3 and F4 ProTaper instruments revealed that the increase in rotational speed significantly reduced the number of cycles to fracture.

2D FEA of evaluation of micromovements and stresses at bone-implant interface in immediately loaded tapered implants in the posterior maxilla.

PubMed

Desai, Shrikar R; Singh, Rika; Karthikeyan, I

2013-09-01

The aim of the study is to evaluate the influence implant length on stress distribution at bone implant interface in single immediately loaded implants when placed in D4 bone quality. A 2-dimensional finite element models were developed to simulate two types of implant designs, standard 3.75 mm-diameter tapered body implants of 6 and 10 mm lengths. The implants were placed in D4 bone quality with a cortical bone thickness of 0.5 mm. The implant design incorporated microthreads at the crestal part and the rest of the implant body incorporated Acme threads. The Acme thread form has a 29° thread angle with a thread height half of the pitch; the apex and valley are flat. A 100 N of force was applied vertically and in the oblique direction (at an angle of 45°) to the long axis of the implants. The respective material properties were assigned. Micro-movements and stresses at the bone implant interface were evaluated. The results of total deformation (micro-movement) and Von mises stress were found to be lower for tapered long implant (10 mm) than short implant (6 mm) while using both vertical as well as oblique loading. Short implants can be successfully placed in poor bone quality under immediate loading protocol. The novel approach of the combination of microthreads at the crestal portion and acme threads for body portion of implant fixture gave promising results.

Correlation between the extent of pneumatization of Agger agger Nasi nasi cells and the anterior-to-posterior length of the frontal recess: A a computer-assisted anatomical study.

PubMed

Altıntaş, Ahmet; Çelik, Mustafa; Yegin, Yakup; Canpolat, Sinan; Olgun, Burak; Tülin Kayhan, Fatma

2017-06-30

To explore the correlation between the volume of the aAgger nNasi (AN) cell bulge and the A-P length of the frontal recess (FR). In total, 120 patients, who underwent septoplasty, were included. All patients underwent preoperative paranasal sinus computed tomography of the paranasal sinuses (PNS CT) imaging. In total, CT data on of all 120 PNSs patients were analyzed in terms of thewith respect to the extent of pneumatization of the AN cell bulge and the A-P dimensions of the FR. Each side was analyzed separately. We included 120 patients,: 78 (65.0%) females and 42 (35.0 %) males. Their average age was 33.7 ± 11.6 years (range: 18-65 years). The mean volume of the AN cell bulge was 0.26 ± 0.4 mm3 on both the right and left sides. The A-P length of the FR was 7.7 ± 2.2 mm. No significant between-side difference in the mean volume of the AN cell bulge was apparent observed (p=0.906). This volume did not differ significantly by age or sex (p=0.844 and p=0.971, respectively). We found no correlation between the volume of the AN cell bulge and the A-P length of the FR (r = 0.098, p=0.192). In the present study, no correlation between AN cell volume and the A-P length of the FR was found. When studying the anatomical complexity of the FR, it is essential to consider the AN cell volume. We suggest that preoperative CT imaging is critical when endoscopic sinus surgery is planned. However, further studies with larger numbers of patients are needed to explore the relationship between AN cell pneumatization and the anatomy of the FR.

Evaluation of COPD's diaphragm motion extracted from 4D-MRI

NASA Astrophysics Data System (ADS)

Swastika, Windra; Masuda, Yoshitada; Kawata, Naoko; Matsumoto, Koji; Suzuki, Toshio; Iesato, Ken; Tada, Yuji; Sugiura, Toshihiko; Tanabe, Nobuhiro; Tatsumi, Koichiro; Ohnishi, Takashi; Haneishi, Hideaki

2015-03-01

We have developed a method called intersection profile method to construct a 4D-MRI (3D+time) from time-series of 2D-MRI. The basic idea is to find the best matching of the intersection profile from the time series of 2D-MRI in sagittal plane (navigator slice) and time series of 2D-MRI in coronal plane (data slice). In this study, we use 4D-MRI to semiautomatically extract the right diaphragm motion of 16 subjects (8 healthy subjects and 8 COPD patients). The diaphragm motion is then evaluated quantitatively by calculating the displacement of each subjects and normalized it. We also generate phase-length map to view and locate paradoxical motion of the COPD patients. The quantitative results of the normalized displacement shows that COPD patients tend to have smaller displacement compared to healthy subjects. The average normalized displacement of total 8 COPD patients is 9.4mm and the average of normalized displacement of 8 healthy volunteers is 15.3mm. The generated phase-length maps show that not all of the COPD patients have paradoxical motion, however if it has paradoxical motion, the phase-length map is able to locate where does it occur.

Influence of Screw Length and Bone Thickness on the Stability of Temporary Implants

PubMed Central

Fernandes, Daniel Jogaib; Elias, Carlos Nelson; Ruellas, Antônio Carlos de Oliveira

2015-01-01

The purpose of this work was to study the influence of screw length and bone thickness on the stability of temporary implants. A total of 96 self-drilling temporary screws with two different lengths were inserted into polyurethane blocks (n = 66), bovine femurs (n = 18) and rabbit tibia (n = 12) with different cortical thicknesses (1 to 8 mm). Screws insertion in polyurethane blocks was assisted by a universal testing machine, torque peaks were collected by a digital torquemeter and bone thickness was monitored by micro-CT. The results showed that the insertion torque was significantly increased with the thickness of cortical bone from polyurethane (p < 0.0001), bovine (p = 0.0035) and rabbit (p < 0.05) sources. Cancellous bone improved significantly the mechanical implant stability. Insertion torque and insertion strength was successfully moduled by equations, based on the cortical/cancellous bone behavior. Based on the results, insertion torque and bone strength can be estimate in order to prevent failure of the cortical layer during temporary screw placement. The stability provided by a cortical thickness of 2 or 1 mm coupled to cancellous bone was deemed sufficient for temporary implants stability. PMID:28793582

Barley processing, forage:concentrate, and forage length effects on chewing and digesta passage in lactating cows.

PubMed

Yang, W Z; Beauchemin, K A; Rode, L M

2001-12-01

Dietary factors that alter fermentability, NDF content, or particle size of the diet were evaluated for their effects on chewing behavior and distribution and passage of feed particles in the digestive tract of dairy cows. A double 4 x 4 quasi-Latin square design with a 2(3) factorial arrangement of treatments was used. The dietary factors were: extent of barley grain processing, coarse (1.60 mm) or flat (1.36 mm); forage-to-concentrate ratio (F:C), low (35:65) or high (55:45) (dry matter basis); and forage particle length, long (7.59 mm) or short (6.08 mm). Eight lactating cows with ruminal and duodenal cannulas were offered ad libitum access to total mixed diets. Chewing time, expressed as minutes per day or per kilogram of dry matter or neutral detergent fiber (NDF), was increased with high F:C diets due to increased eating and ruminating times but was decreased when expressed per kilogram of NDF intake from forage. The influence of forage particle length or grain processing on chewing activity was less pronounced than F:C ratio. Chewing activity was positively correlated to proportion of long forage particles in the diet but not to particle length of the diets. Influence of feed particle size on particle size distribution in different sites of the digestive tract was minimal. Particle size distributions of duodenal digesta and feces differed; the proportion of particles retained on the 3.35- or 1.18-mm screens was higher, but proportion of particles that passed through the 1.18-mm screen was lower in duodenal digesta than in feces. Relationships between chewing activities and ruminal pH or fractional passage rate of rumen contents were not significant. These results indicate that particle size of barley-based diets was not a reliable indicator of chewing activity. Forage particle size and NDF content of the diets were more reliable indicators of chewing activity than was the NDF content of forage. Fecal particle size was not an appropriate means of estimating the size of particles exiting the reticulorumen, at least for barley-based diets. Breakdown of coarse particles was necessary, but not a rate-limiting step for particles exiting the rumen. Passage rate of the rumen contents was affected by numerous factors including chewing activity.

Crack networks in damaged glass

NASA Astrophysics Data System (ADS)

Mallet, Celine; Fortin, Jerome; Gueguen, Yves

2013-04-01

We investigate how cracks develop and propagate in synthetic glass samples. Cracks are introduced in glass by a thermal shock of 300oC. Crack network is documented from optical and electronic microscopy on these samples that have been submitted to a thermal shock only. Samples are cylinder of 80 mm length and 40 mm diameter. Sections were cut along the cylinder axis and perpendicular to it. Using SEM, crack lengths and apertures can be measured. Optical microscopy allows to get the crack distribution over the entire sample. The sample average crack length is 3 mm. The average aperture is 6 ± 3μm. There is however a clear difference between the sample core, where the crack network has approximatively a transverse isotrope symmetry and the outer ring, where cracks are smaller and more numerous. By measuring before and after the thermal treatment the radial P and S wave velocities in room conditions, we can determine the total crack density which is 0.24. Thermally cracked samples, as described above, were submitted to creep tests. Constant axial stress and lateral stress were applied. Several experiments were performed at different stress values. Samples are saturated for 48 hours (to get an homogeneous pore fluid distribution), the axial stress is increased up to 80% of the sample strength. Stress step tests were performed in order to get creep data. The evolution of strain (axial and radial strain) is measured using strain gages, gap sensors (for the global axial strain) and pore volume change (for the volumetric strain). Creep data are interpreted as evidence of sub-critical crack growth in the cracked glass samples. The above microstructural observations are used, together with a crack propagation model, to account for the creep behavior. Assuming that (i) the observed volumetric strain rate is due to crack propagation and (ii) crack aspect ratio is constant we calculate the creep rate. We obtain some value on the crack propagation during a 24 hours of constant stress test. At each of these test, crack propagate of 0.3 to 0.4 mm. From the initial average crack length of 3 mm, the crack reach the size of 5.8 mm at the end of a complete creep test (with 8 constant stress step of 24 hours).

Aerosol based direct-write micro-additive fabrication method for sub-mm 3D metal-dielectric structures

NASA Astrophysics Data System (ADS)

Rahman, Taibur; Renaud, Luke; Heo, Deuk; Renn, Michael; Panat, Rahul

2015-10-01

The fabrication of 3D metal-dielectric structures at sub-mm length scale is highly important in order to realize low-loss passives and GHz wavelength antennas with applications in wearable and Internet-of-Things (IoT) devices. The inherent 2D nature of lithographic processes severely limits the available manufacturing routes to fabricate 3D structures. Further, the lithographic processes are subtractive and require the use of environmentally harmful chemicals. In this letter, we demonstrate an additive manufacturing method to fabricate 3D metal-dielectric structures at sub-mm length scale. A UV curable dielectric is dispensed from an Aerosol Jet system at 10-100 µm length scale and instantaneously cured to build complex 3D shapes at a length scale  <1 mm. A metal nanoparticle ink is then dispensed over the 3D dielectric using a combination of jetting action and tilted dispense head, also using the Aerosol Jet technique and at a length scale 10-100 µm, followed by the nanoparticle sintering. Simulation studies are carried out to demonstrate the feasibility of using such structures as mm-wave antennas. The manufacturing method described in this letter opens up the possibility of fabricating an entirely new class of custom-shaped 3D structures at a sub-mm length scale with potential applications in 3D antennas and passives.

SU-G-JeP2-13: Spatial Accuracy Evaluation for Real-Time MR Guided Radiation Therapy Using a Novel Large-Field MRI Distortion Phantom

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antolak, A; Bayouth, J; Bosca, R

Purpose: Evaluate a large-field MRI phantom for assessment of geometric distortion in whole-body MRI for real-time MR guided radiation therapy. Methods: A prototype CIRS large-field MRI distortion phantom consisting of a PMMA cylinder (33 cm diameter, 30 cm length) containing a 3D-printed orthogonal grid (3 mm diameter rods, 20 mm apart), was filled with 6 mM NiCl{sub 2} and 30 mM NaCl solution. The phantom was scanned at 1.5T and 3.0T on a GE HDxt and Discovery MR750, respectively, and at 0.35T on a ViewRay system. Scans were obtained with and without 3D distortion correction to demonstrate the impact ofmore » such corrections. CT images were used as a reference standard for analysis of geometric distortion, as determined by a fully automated gradient-search method developed in Matlab. Results: 1,116 grid points distributed throughout a cylindrical volume 28 cm in diameter and 16 cm in length were identified and analyzed. With 3D distortion correction, average/maximum displacements for the 1.5, 3.0, and 0.35T systems were 0.84/2.91, 1.00/2.97, and 0.95/2.37 mm, respectively. The percentage of points with less than (1.0, 1.5, 2.0 mm) total displacement were (73%, 92%, 97%), (54%, 85%, 97%), and (55%, 90%, 99%), respectively. A reduced scan volume of 20 × 20 × 10 cm{sup 3} (representative of a head and neck scan volume) consisting of 420 points was also analyzed. In this volume, the percentage of points with less than (1.0, 1.5, 2.0 mm) total displacement were (90%, 99%, 100%), (63%, 95%, 100%), and (75%, 96%, 100%), respectively. Without 3D distortion correction, average/maximum displacements were 1.35/3.67, 1.67/4.46, and 1.51/3.89 mm, respectively. Conclusion: The prototype large-field MRI distortion phantom and developed software provide a thorough assessment of 3D spatial distortions in MRI. The distortions measured were acceptable for RT applications, both for the high field strengths and the system configuration developed by ViewRay.« less

Experimental evaluation of size-dependent predation by adult post-spawned rainbow smelt (Osmerus mordax) on larval lake whitefish (Coregonus clupeaformis)

USGS Publications Warehouse

Zydlewski, Joseph D.; Gorsky, Dimitry

2013-01-01

Introduced landlocked Rainbow Smelt Osmerus mordax are hypothesized to be a major factor in the decline of Lake Whitefish Coregonus clupeaformis populations in many lakes. We sought to identify the size of Lake Whitefish preyed upon by adult Rainbow Smelt and how the efficiency of Rainbow Smelt predation changes Lake Whitefish ontogeny. In a laboratory setting, we exposed larval Lake Whitefish of increasing sizes to groups of seven Rainbow Smelt (>100 mm) for a 1-h period and observed predation behaviors and efficiencies. In each trial, the group of Rainbow Smelt consumed at least one larval Lake Whitefish, which were up to 45 mm in length (up to 89% of Rainbow Smelt gape width). Predation efficiency, the total number of Lake Whitefish consumed by Rainbow Smelt during trials, was 100% after Lake Whitefish hatching and followed a decreasing sigmoidal response to increasing lengths of Lake Whitefish. The apparent predatory window of Rainbow Smelt on Lake Whitefish is from Lake Whitefish size at hatch (∼12 mm) to approximately 34 mm. Rainbow Smelt generally required multiple attacks to capture a single Lake Whitefish. The capture efficiencies of Rainbow Smelt decreased from 30% as Lake Whitefish length increased and were highly variable within each Lake Whitefish size-group. The overall impact that Rainbow Smelt predation will have on Lake Whitefish populations is dependent on the growth rate of Lake Whitefish, environmental conditions that cause the Lake Whitefish hatching period to coincide with Rainbow Smelt spawning events, and the degree of overlap in habitat use between spawning Rainbow Smelt, nonspawning subadult Rainbow Smelt, and hatching Lake Whitefish.

Evaluation of very long baseline interferometry atmospheric modeling improvements

NASA Technical Reports Server (NTRS)

Macmillan, D. S.; Ma, C.

1994-01-01

We determine the improvement in baseline length precision and accuracy using new atmospheric delay mapping functions and MTT by analyzing the NASA Crustal Dynamics Project research and development (R&D) experiments and the International Radio Interferometric Surveying (IRIS) A experiments. These mapping functions reduce baseline length scatter by about 20% below that using the CfA2.2 dry and Chao wet mapping functions. With the newer mapping functions, average station vertical scatter inferred from observed length precision (given by length repeatabilites) is 11.4 mm for the 1987-1990 monthly R&D series of experiments and 5.6 mm for the 3-week-long extended research and development experiment (ERDE) series. The inferred monthly R&D station vertical scatter is reduced by 2 mm or by 7 mm is a root-sum-square (rss) sense. Length repeatabilities are optimum when observations below a 7-8 deg elevation cutoff are removed from the geodetic solution. Analyses of IRIS-A data from 1984 through 1991 and the monthly R&D experiments both yielded a nonatmospheric unmodeled station vertical error or about 8 mm. In addition, analysis of the IRIS-A exeriments revealed systematic effects in the evolution of some baseline length measurements. The length rate of change has an apparent acceleration, and the length evolution has a quasi-annual signature. We show that the origin of these effects is unlikely to be related to atmospheric modeling errors. Rates of change of the transatlantic Westford-Wettzell and Richmond-Wettzell baseline lengths calculated from 1988 through 1991 agree with the NUVEL-1 plate motion model (Argus and Gordon, 1991) to within 1 mm/yr. Short-term (less than 90 days) variations of IRIS-A baseline length measurements contribute more than 90% of the observed scatter about a best fit line, and this short-term scatter has large variations on an annual time scale.

Radiographic parameters improve lower extremity prosthetic alignment.

PubMed

Mooney, Ryan; Carry, Patrick; Wylie, Erin; Schultz, Abby; McNair, Bryan; Page, Carol; Biffl, Susan; Heare, Travis

2013-12-01

The goal of prosthetic fitting is to provide comfort and functionality to the patient. It is thought that incorporating the use of standing anterior-posterior long leg radiographs (LLR) into the fitting of lower extremity prostheses will provide an objective guide when making adjustments, and be a better assessment of alignment. This study compares prosthetic alignment before and after radiography-guided adjustments. This retrospective study was performed at a multidisciplinary amputee clinic on patients with congenital and/or acquired limb deficiencies. Their prosthetic alignment was evaluated by LLR and adjusted as needed. Satisfactory alignment was defined as a mechanical axis angular deviation of ≤1° and a leg length discrepancy of ≤10 mm. A total of 45 unique prostheses from 24 subjects (10 female and 14 male) were included. Post-adjustment radiographs were obtained from 29 prostheses. After the initial prosthetic fitting, the probability of a satisfactory fit was 20.0 % (95 % CI 10.9-34.9 %). Following the baseline adjustment, the probability of a satisfactory fit improved to 53.3 % (95 % CI 37.5-70.9 %). After adjustment number 4, the probability of a satisfactory fit further improved to 76.7 % (95 % CI 41.9-98.0 %). There were also significant improvements in distal offset distance (p = 0.0040) and leg length discrepancy (p = 0.0206). The distal offset distance decreased by an average of 10.7 mm (95 % CI 3.6-17.8), and leg length discrepancy decreased by an average of 3.0 mm (95 % CI 00.48-5.5). The addition of LLRs to existing fitting methods significantly improves prosthetic alignment and length.

An Evaluation Method for Suppression of Pathogenic Fusarium oxysporum by Soil Microorganisms Using the Dilution Plate Technique.

PubMed

Mitsuboshi, Masahiro; Kioka, Yuuzou; Noguchi, Katsunori; Asakawa, Susumu

2017-01-01

Volume 31, No. 3, Page 307-313, 2016Page 310, Legend for Fig. 4 IncorrectFig. 4. Growth degree of Fusarium oxysporum f. sp. spinaciae for organic fertilizers at each dilution based on an estimation of the ellipse area (A) and extension length (B) of the colony. Cont, compound inorganic fertilizer; SBM, steamed bone meal; CDC, cow dung compost; MI, microbial inoculant. Values show mean of medians of degrees with SE (n=3). The ellipse area and extension length for control plates were 4,475 mm 2 and 36.5 mm, respectively. CorrectFig. 4. Growth degree of Fusarium oxysporum f. sp. spinaciae for organic fertilizers at each dilution based on an estimation of the ellipse area (A) and extension length (B) of the colony. Cont, compound inorganic fertilizer; SBM, steamed bone meal; CDC, cow dung compost; MI, microbial inoculant. Values show mean of growth degrees with SE (n=3). The ellipse area and extension length for control plates were 4,475 mm 2 and 36.5 mm, respectively. Page 311, Legend for Fig. 5 IncorrectFig. 5. Growth degree of Fusarium oxysporum f. sp. spinaciae for soil applied with organic fertilizers at each dilution based on an estimation of the ellipse area (A) and extension length (B) of the colony. Cont, compound inorganic fertilizer; SBM, steamed bone meal; CDC, cow dung compost; MI, microbial inoculant. Values show the mean of medians of degrees with SE (n=3). The ellipse area and extension length for control plates were 5,473 mm 2 and 40.5 mm, respectively. CorrectFig. 5. Growth degree of Fusarium oxysporum f. sp. spinaciae for soil applied with organic fertilizers at each dilution based on an estimation of the ellipse area (A) and extension length (B) of the colony. Cont, compound inorganic fertilizer; SBM, steamed bone meal; CDC, cow dung compost; MI, microbial inoculant. Values show the mean of growth degrees with SE (n=3). The ellipse area and extension length for control plates were 5,473 mm 2 and 40.5 mm, respectively. Page 312, Legend for Fig. 7 IncorrectFig. 7. Growth degree of Fusarium oxysporum f. sp. spinaciae at each dilution based on an estimation of the ellipse area (A) and extension length (B) of the colony. Cont, compound inorganic fertilizer; SBM, steamed bone meal; CDC, cow dung compost; MI2, microbial inoculant applied with 2,000 kg ha -1 ; MI10, microbial inoculant applied with 10,000 kg ha -1 . Values show the mean of medians of degrees with SE (n=3). The ellipse area and extension length for control plates were 3,404 mm 2 and 29.7 mm, respectively. CorrectFig. 7. Growth degree of Fusarium oxysporum f. sp. spinaciae at each dilution based on an estimation of the ellipse area (A) and extension length (B) of the colony. Cont, compound inorganic fertilizer; SBM, steamed bone meal; CDC, cow dung compost; MI2, microbial inoculant applied with 2,000 kg ha -1 ; MI10, microbial inoculant applied with 10,000 kg ha -1 . Values show the mean of growth degrees with SE (n=3). The ellipse area and extension length for control plates were 3,404 mm 2 and 29.7 mm, respectively. The authors would like to apologize for these corrections and any inconvenience caused.

Evaluation of an adaptive detector collimation for prospectively ECG-triggered coronary CT angiography with third-generation dual-source CT.

PubMed

Messerli, Michael; Dewes, Patricia; Scholtz, Jan-Erik; Arendt, Christophe; Wildermuth, Simon; Vogl, Thomas J; Bauer, Ralf W

2018-05-01

To investigate the impact of an adaptive detector collimation on the dose parameters and accurateness of scan length adaption at prospectively ECG-triggered sequential cardiac CT with a wide-detector third-generation dual-source CT. Ideal scan lengths for human hearts were retrospectively derived from 103 triple-rule-out examinations. These measures were entered into the new scanner operated in prospectively ECG-triggered sequential cardiac scan mode with three different detector settings: (1) adaptive collimation, (2) fixed 64 × 0.6-mm collimation, and (3) fixed 96 × 0.6-mm collimation. Differences in effective scan length and deviation from the ideal scan length and dose parameters (CTDIvol, DLP) were documented. The ideal cardiac scan length could be matched by the adaptive collimation in every case while the mean scanned length was longer by 15.4% with the 64 × 0.6 mm and by 27.2% with the fixed 96 × 0.6-mm collimation. While the DLP was almost identical between the adaptive and the 64 × 0.6-mm collimation (83 vs. 89 mGycm at 120 kV), it was 62.7% higher with the 96 × 0.6-mm collimation (135 mGycm), p < 0.001. The adaptive detector collimation for prospectively ECG-triggered sequential acquisition allows for adjusting the scan length as accurate as this can only be achieved with a spiral acquisition. This technique allows keeping patient exposure low where patient dose would significantly increase with the traditional step-and-shoot mode. • Adaptive detector collimation allows keeping patient exposure low in cardiac CT. • With novel detectors the desired scan length can be accurately matched. • Differences in detector settings may cause 62.7% of excessive dose.

The use of reinforced composite resin cement as compensation for reduced post length.

PubMed

Nissan, J; Dmitry, Y; Assif, D

2001-09-01

Cements that yield high retentive values are believed to allow use of shorter posts. This study investigated the use of reinforced composite resin cement as compensation for reduced dowel length. The retention values of stainless steel posts (parallel-sided ParaPost and tapered Dentatus in 5-, 8-, and 10-mm lengths) luted with Flexi-Flow titanium-reinforced composite resin and zinc phosphate cements were evaluated. Single-rooted extracted human teeth with crowns (n = 120), removed at the cementoenamel junction, were randomly divided into 4 groups of 30 samples each. Different post lengths were luted with either Flexi-Flow or zinc phosphate. Each sample was placed into a specialized jig and on a tensile testing machine with a crosshead speed of 2 mm/min, applied until failure. The effect of different posts and cements on the force required to dislodge the dowels was evaluated with multiple analyses of variance (ANOVA). One-way ANOVA with Scheffé contrast was applied to determine the effect of different post lengths on the retentive failure of posts luted with the 2 agents. Flexi-Flow reinforced composite resin cement significantly increased retention of ParaPost and Dentatus dowels (P<.001) compared with zinc phosphate. One-way ANOVA revealed no statistically significant difference (P>.05) between mean retention of both dowels luted with Flexi-Flow for all posts length used (5 mm = 8 mm = 10 mm). Mean retention values of the groups luted with zinc phosphate showed a statistically significant difference (P<.001) for the different post lengths (10 > 8 > 5 mm). Parallel-sided ParaPost dowels demonstrated a higher mean retention than tapered Dentatus dowels (P<.001). In this study, Flexi-Flow reinforced composite resin cement compensated for the reduced length of shorter parallel-sided ParaPost and tapered Dentatus dowels.

Deformation of Extruded Titanium Alloys Under Superplastic Conditions

DTIC Science & Technology

1988-07-01

176mm wide with a flange wall 37mm high x 27mm wide and a central web 122mm wide x 18mm thick. Round-bar test pieces aligned parallel to the principal...directions L, T and ST were extrac- ted from the flange and web as shown in Fig 1; gauge length dimensions were 15mm x 5.5mm diameter for the FST test...ares. in the gauge length. Flange Web X 9 NTIS GFA&I v FL Distribut I oc / A es ’- n:ia or Fig I Position of test pieces in extruded section iste i

SU-E-J-219: Quantitative Evaluation of Motion Effects On Accuracy of Image-Guided Radiotherapy with Fiducial Markers Using CT Imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ali, I; Oyewale, S; Ahmad, S

2014-06-01

Purpose: To investigate quantitatively patient motion effects on the localization accuracy of image-guided radiation with fiducial markers using axial CT (ACT), helical CT (HCT) and cone-beam CT (CBCT) using modeling and experimental phantom studies. Methods: Markers with different lengths (2.5 mm, 5 mm, 10 mm, and 20 mm) were inserted in a mobile thorax phantom which was imaged using ACT, HCT and CBCT. The phantom moved with sinusoidal motion with amplitudes ranging 0–20 mm and a frequency of 15 cycles-per-minute. Three parameters that include: apparent marker lengths, center position and distance between the centers of the markers were measured inmore » the different CT images of the mobile phantom. A motion mathematical model was derived to predict the variations in the previous three parameters and their dependence on the motion in the different imaging modalities. Results: In CBCT, the measured marker lengths increased linearly with increase in motion amplitude. For example, the apparent length of the 10 mm marker was about 20 mm when phantom moved with amplitude of 5 mm. Although the markers have elongated, the center position and the distance between markers remained at the same position for different motion amplitudes in CBCT. These parameters were not affected by motion frequency and phase in CBCT. In HCT and ACT, the measured marker length, center and distance between markers varied irregularly with motion parameters. The apparent lengths of the markers varied with inverse of the phantom velocity which depends on motion frequency and phase. Similarly the center position and distance between markers varied inversely with phantom speed. Conclusion: Motion may lead to variations in maker length, center position and distance between markers using CT imaging. These effects should be considered in patient setup using image-guided radiation therapy based on fiducial markers matching using 2D-radiographs or volumetric CT imaging.« less

Influence of the geometry of curved artificial canals on the fracture of rotary nickel-titanium instruments subjected to cyclic fatigue tests.

PubMed

Lopes, Hélio P; Vieira, Márcia V B; Elias, Carlos N; Gonçalves, Lucio S; Siqueira, José F; Moreira, Edson J L; Vieira, Victor T L; Souza, Letícia C

2013-05-01

This study evaluated the influence of different features of canal curvature geometry on the number of cycles to fracture of a rotary nickel-titanium endodontic instrument subjected to a cyclic fatigue test. BioRaCe BR4C instruments (FKG Dentaire, La Chaux-de Fonds, Switzerland) were tested in 4 grooves simulating curved metallic artificial canals, each one measuring 1.5 mm in width, 20 mm in total length, and 3.5 mm in depth with a U-shaped bottom. The parameters of curvature including the radius and arc lengths and the position of the arc differed in the 4 canal designs. Fractured surfaces and helical shafts of the separated instruments were analyzed by scanning electron microscopy. The Student's t test showed that a significantly lower number of cycles to fracture values were observed for instruments tested in canals with the smallest radius, the longest arc, and the arc located in the middle portion of the canal. Scanning electron microscopic analysis of the fracture surfaces revealed morphologic characteristics of ductile fracture. Plastic deformation was not observed in the helical shaft of the fractured instruments. Curvature geometry including the radius and arc lengths and the position of the arc along the root canal influence the number of cycles to fracture of rotary nickel-titanium instruments subjected to flexural load. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effect of nitrogen sources on some morphological characteristics of in vitro stevia rebaudiana Bertoni.

PubMed

Akbari, F; Arminian, A; Kahrizi, D; Fazeli, A

2017-02-28

Stevia rebaudiana Bertoni belongs to Asteraceae family that leaves 200-300 times sweeter than sugar. Low seed fertility is one of the most important problems in Stevia production. So, Plant tissue culture is an efficient method for mass propagation of Stevia. In this research, we studied the effect of various concentrations of nitrogen on some morphological traits of stevia under in vitro conditions. We used axillary nodes as explants and they were cultured on Murashige and Skoog (MS) medium containing inorganic nitrogen sources i.e. NH4NO3(0, 825 and 1650 mg/l), KNO3(0, 950 and 1900 mg/l) were observed. The cultures were kept for 4 weeks at a temperature of 25±2°C with a photoperiod of 16/8 hour low light/dark each day. Maximum shoot length (89.33 mm), dry weight of plants (0.10 mg) and leaf fresh weight (0.42 mg) was observed on MS medium with 1650 mg/l NH4NO3 and 950 mg/l KNO3. Minimum shoot length (6.13 mm), root length (6.60 mm), leaf number (4.26), leaf dry weight (0.01 mg), leaf fresh weight (0.05 mg), total dry and fresh weight (0.02 and 0.15 mg) and growth rate was observed on a MS medium without nitrogen sources. Moreover, presence of nitrogen sources increases both shooting and rooting in Stevia rebaudiana Bertoni.

Soft Biomimetic Fish Robot Made of Dielectric Elastomer Actuators.

PubMed

Shintake, Jun; Cacucciolo, Vito; Shea, Herbert; Floreano, Dario

2018-06-29

This article presents the design, fabrication, and characterization of a soft biomimetic robotic fish based on dielectric elastomer actuators (DEAs) that swims by body and/or caudal fin (BCF) propulsion. BCF is a promising locomotion mechanism that potentially offers swimming at higher speeds and acceleration rates, and efficient locomotion. The robot consists of laminated silicone layers wherein two DEAs are used in an antagonistic configuration, generating undulating fish-like motion. The design of the robot is guided by a mathematical model based on the Euler-Bernoulli beam theory and takes account of the nonuniform geometry of the robot and of the hydrodynamic effect of water. The modeling results were compared with the experimental results obtained from the fish robot with a total length of 150 mm, a thickness of 0.75 mm, and weight of 4.4 g. We observed that the frequency peaks in the measured thrust force produced by the robot are similar to the natural frequencies computed by the model. The peak swimming speed of the robot was 37.2 mm/s (0.25 body length/s) at 0.75 Hz. We also observed that the modal shape of the robot at this frequency corresponds to the first natural mode. The swimming of the robot resembles real fish and displays a Strouhal number very close to those of living fish. These results suggest the high potential of DEA-based underwater robots relying on BCF propulsion, and applicability of our design and fabrication methods.

High-speed fiber laser cutting of thick stainless steel for dismantling tasks

NASA Astrophysics Data System (ADS)

Shin, Jae Sung; Oh, Seong Yong; Park, Hyunmin; Chung, Chin-Man; Seon, Sangwoo; Kim, Taek-Soo; Lee, Lim; Choi, Byung-Seon; Moon, Jei-Kwon

2017-09-01

A high-speed fiber laser cutting technology of thick steels for dismantling tasks was achieved using a 6-kW fiber laser system. At first, a new cutting head for efficient cutting of thick steels was developed, which was composed by a collimator with a focal length of 160 mm and mirror-type focusing objects with a long focal length of 600 mm. The long focal length of the focusing object made it possible for the beam size to be small through the thick cutting material and the cutting efficiency was expected to increase compared with the short focal length. In addition, folding the beam facilitated the compact cutting head with a size of 160 mm (width) × 80 mm (height) × 640 mm (length) and a weight of 6.9 kg. In the cutting experiment, the laser beam was delivered to the cutting head by a 25-m long process fiber with a core diameter of 100 μm. The cutting performances were studied against the thicknesses of stainless steel plates. A maximum cutting speed of 72 mm/min was obtained for the 60-mm thick stainless steel plate cutting and the cut specimen showed an excellent kerf shape and a narrow kerf width. To the best of our knowledge, this cutting speed was higher than other previously reported results when cutting with a 6-kW laser power.

Differences in the Tensor Veli Palatini Between Adults With and Without Cleft Palate Using High-Resolution 3-Dimensional Magnetic Resonance Imaging.

PubMed

George, Thomas N; Kotlarek, Katelyn J; Kuehn, David P; Sutton, Bradley P; Perry, Jamie L

2018-05-01

To investigate the dimensions of the tensor veli palatini (TVP) muscle in adults with and without cleft palate. Prospective study. There were a total of 14 adult participants, 8 noncleft and 6 with cleft palate. Analysis and comparison of the TVP muscle and surrounding structures was completed using 3D MRI data and Amira 5.5 Visualization Modeling software. TVP muscle volume, hamular process distance, mucosal thickness, TVP muscle length, and TVP muscle diameter were used for comparison between participant groups based upon previous research methods. Mann-Whitney U tests revealed a significantly smaller ( U < .001, P = .002) TVP muscle volume in the cleft palate group (median = 536.22 mm 3 ) compared to individuals in the non-cleft palate group (median = 895.19 mm 3 ). The TVP muscle was also significantly shorter ( U = 1.00, P = .003) in the cleft palate group (median = 18.04 mm) versus the non-cleft palate (median = 21.18 mm). No significant differences were noted for the other measured parameters. Significant differences in the TVP muscle volume and length among the noncleft participants found in this study may insights into the reported increased incidence of otitis media with effusion (OME) seen in the cleft population. Results from this study contribute to our understanding of the underlying anatomic differences among individuals with cleft palate.

Morphological Characterization of the African Giant Rat (Cricetomys gambianus, Waterhouse) Brain Across Age Groups: Gross Features of Cortices.

PubMed

Olude, M A; Mustapha, O A; Olopade, J O

2017-03-06

This experiment was designed to investigate the morphological characterization of the brain cortices of African giant rats, AGR (Cricetomys gambianus, Waterhouse) across age groups as related to function. A total of 15 male AGR were used for this study comprising of 5 neonates, 5 juveniles and 5 adults. Brains were described as having typical rodent features; the falx cerebri, the dura modification of interest, was partly inserted between the lobes of the olfactory bulb and extended towards the corpus callosum. Gross parameters extrapolated include cerebral and cerebellar cortical dimensions using a oneway ANOVA (p≤0.05). Most values showed highest significant value bias for juveniles over adults and neonates.  The average brain weight was 5.60±0.06g, 4.64±0.17g and 0.62±0.08g; cortex volume: 2.84±0.04cm3, 3.16±0.10cm3 and 0.23±0.02cm3 and antero-posterior dimensions: 11.93±0.26mm, 14.54±0.22mm and 6.00±0.16mm for adult, juvenile and neonates respectively. There was however adult bias in the cerebellum weight (0.83±0.02g, 0.76±0.02g and 0.04±0.02g); vermis length (13.23±0.32mm, 11.27±0.014mm and 0.24±0.02mm) and the antero-posterior length values (8.79±0.19mm, 6.97±0.03mm and 0.29±0.01mm) for adults, juveniles and neonates AGR respectively. Cortical parameters were related as a function of the brain development and plasticity, while age was described to play functional roles in intelligence determination of the AGR. The result of this study will be useful as baseline information for post mortem studies, medical imaging and useful as diagnostic tool for future research work on the AGR brain.

Oxidised zirconium versus cobalt alloy bearing surfaces in total knee arthroplasty: 3D laser scanning of retrieved polyethylene inserts.

PubMed

Anderson, F L; Koch, C N; Elpers, M E; Wright, T M; Haas, S B; Heyse, T J

2017-06-01

We sought to establish whether an oxidised zirconium (OxZr) femoral component causes less loss of polyethylene volume than a cobalt alloy (CoCr) femoral component in total knee arthroplasty. A total of 20 retrieved tibial inserts that had articulated with OxZr components were matched with 20 inserts from CoCr articulations for patient age, body mass index, length of implantation, and revision diagnosis. Changes in dimensions of the articular surfaces were compared with those of pristine inserts using laser scanning. The differences in volume between the retrieved and pristine surfaces of the two groups were calculated and compared. The loss of polyethylene volume was 122 mm 3 (standard deviation (sd) 87) in the OxZr group and 170 mm 3 (sd 96) in the CoCr group (p = 0.033). The volume loss in the OxZr group was also lower in the medial (72 mm 3 (sd 67) versus 92 mm 3 (sd 60); p = 0.096) and lateral (49 mm 3 (sd 36) versus 79 mm 3 (sd 61); p = 0.096) compartments separately, but these differences were not significant. Our results corroborate earlier findings from in vitro testing and visual retrieval analysis which suggest that polyethylene volume loss is lower with OxZr femoral components. Since both OxZr and CoCr are hard surfaces that would be expected to create comparable amounts of polyethylene creep, the differences in volume loss may reflect differences in the in vivo wear of these inserts. Cite this article: Bone Joint J 2017;99-B:793-8. ©2017 The British Editorial Society of Bone & Joint Surgery.

Large-scale fiber release and equipment exposure experiments. [aircraft fires

NASA Technical Reports Server (NTRS)

Pride, R. A.

1980-01-01

Outdoor tests were conducted to determine the amount of fiber released in a full scale fire and trace its dissemination away from the fire. Equipment vulnerability to fire released fibers was assessed through shock tests. The greatest fiber release was observed in the shock tube where the composite was burned with a continuous agitation to total consumption. The largest average fiber length obtained outdoors was 5 mm.

Pre-operative digital templating in cemented hip hemiarthroplasty for neck of femur fractures.

PubMed

Kwok, Iris H Y; Pallett, Scott J C; Massa, Edward; Cundall-Curry, Duncan; Loeffler, Mark D

2016-03-01

Pre-operative digital templating allows the surgeon to foresee any anatomical anomalies which may lead to intra-operative problems, and anticipate appropriate instruments and implants required during surgery. Although its role is well-established in successful elective total hip arthroplasty, little work has been done on its use in hip hemiarthroplasty in neck of femur fractures. We describe our initial experience of digital templating in 40 consecutive patients who have undergone cemented hip hemiarthroplasty, assessing templating accuracy between templated implant sizes to actual implant sizes. 81% of implanted heads were templated to within two head sizes, and 89% of implanted stems were templated to within two sizes. Although there was a moderately strong correlation of 0.52 between templated and actual head sizes, this correlation was not demonstrated in femoral stem sizes. Mean leg length discrepancy was -2.5mm (S.D. 8.5), and the mean difference in femoral offset between the operated and non-operated hip was -1mm (S.D. 4.4). Digital templating is a useful adjunct to the surgeon in pre-operative planning of hip hemiarthroplasty in the restoration of leg length and femoral offset. However, its accuracy is inferior to that of elective total hip arthroplasty. Copyright © 2016 Elsevier Ltd. All rights reserved.

RESISTANCE TO X-IRRADIATION BY EMBRYONIC CELLS OF THE LIMB-BUDS OF TADPOLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen, B.M.; Ewell, L.M.

1959-01-01

Both total-body irradiation and shielding of the trunk were used to study the effects of x irradiation from 1000 to 30000 r upon the limb-buds of Bufo boreas and Hyla regilla tadpoles. The object was to test the view that the younger the cells the more sensitive they are to irradiation. The answer is negative. If there is any special susceptibility of these undifferentiated cells it should appear at levels far below the 30000 r maximum employed. A sharp distinction is made between the very susceptible mitotic cells and the resistant non-dividing embryonic cells that have been accumulated in suchmore » numbers that they may rapidly differentiate into the characteristic limb tissues under the stimulus of the thyroid hormone. Many irradiated ectoderm cells were changed to form bizarre excrescences but were not destroyed. Unicellular cuthneous gland cells continued to arise even after the heaviest irradiation. Irradiated tadpoles with hind limb-buds from 0.6 mm down to 0.2 mm length were unable to develop normal limbs. This capacity was propontional to the number of non-dividing embryonic cells stored at the time of irradiation. Irradiation of 5000, equal degree but the rapidity was greatest in the cases of higher dosage. Not only did these levels of irradiation fail to destroy the non-dividing embryonic cells but they did not effect their pre-deterrmined specificity nor modify their capacity for subsequent differentiation and growth. Exposure to a thyroxin solution caused the hind limb-buds without visible differentiation of cells to grow from a length of 0.8 or 0.9 mm or 1.0 mm at the time of irradiation to a length of as much as 5.0 mm in the course of 7 days. Development of thigh, shank, ankle, and toes was complete. Microscopic studies showed characteristic tissues such as cartilage, connective tissue, and muscle, developed to a comparable degree in control and irradiated specimens. (auth)« less

Volume and contact surface area analysis of bony tunnels in single and double bundle anterior cruciate ligament reconstruction using autograft tendons: in vivo three-dimensional imaging analysis.

PubMed

Yang, Jae-Hyuk; Chang, Minho; Kwak, Dai-Soon; Wang, Joon Ho

2014-09-01

Regarding reconstruction surgery of the anterior cruciate ligament (ACL), there is still a debate whether to perform a single bundle (SB) or double bundle (DB) reconstruction. The purpose of this study was to analyze and compare the volume and surface area of femoral and tibial tunnels during transtibial SB versus transportal DB ACL reconstruction. A consecutive series of 26 patients who underwent trantibial SB ACL reconstruction and 27 patients with transportal DB ACL reconstruction using hamstring autograft from January 2010 to October 2010 were included in this study. Three-dimensional computed tomography (3D-CT) was taken within one week after operation. The CT bone images were segmented with use of Mimics software v14.0. The obtained digital images were then imported in the commercial package Geomagic Studio v10.0 and SketchUp Pro v8.0 for processing. The femoral and tibial tunnel lengths, diameters, volumes and surface areas were evaluated. A comparison between the two groups was performed using the independent-samples t-test. A p-value less than the significance value of 5% (p < 0.05) was considered statistically significant. Regarding femur tunnels, a significant difference was not found between the tunnel volume for SB technique (1,496.51 ± 396.72 mm(3)) and the total tunnel volume for DB technique (1,593.81 ± 469.42 mm(3); p = 0.366). However, the total surface area for femoral tunnels was larger in DB technique (919.65 ± 201.79 mm(2)) compared to SB technique (810.02 ± 117.98 mm(2); p = 0.004). For tibia tunnels, there was a significant difference between tunnel volume for the SB technique (2,070.43 ± 565.07 mm(3)) and the total tunnel volume for the DB technique (2,681.93 ± 668.09 mm(3); p ≤ 0.001). The tibial tunnel surface area for the SB technique (958.84 ± 147.50 mm(2)) was smaller than the total tunnel surface area for the DB technique (1,493.31 ± 220.79 mm(2); p ≤ 0.001). Although the total femoral tunnel volume was similar between two techniques, the total surface area was larger in the DB technique. For the tibia, both total tunnel volume and the surface area were larger in DB technique.

Axial Length Measurement Failure Rates With Biometers Using Swept-Source Optical Coherence Tomography Compared to Partial-Coherence Interferometry and Optical Low-Coherence Interferometry.

PubMed

McAlinden, Colm; Wang, Qinmei; Gao, Rongrong; Zhao, Weiqi; Yu, Ayong; Li, Yu; Guo, Yan; Huang, Jinhai

2017-01-01

To compare a new swept-source optical coherence tomography (SSOCT)-based biometer (OA-2000) with the IOLMaster v5.4 (partial-coherence interferometry) and Aladdin (optical low-coherence interferometry) biometers in terms of axial length measurement and failure rate in eyes with cataract. Reliability study. A total of 377 eyes of 210 patients were scanned with the 3 biometers in a random order. For each biometer, the number of unobtainable axial length measurements was recorded and grouped as per the type and severity of cataract based on the Lens Opacities Classification System III by the same experienced ophthalmologist. The Bland-Altman limits-of-agreement (LoA) method was used to assess the agreement in axial length measurements between the 3 biometers. The failure rate was 0 eyes (0%) with the OA-2000, 136 eyes (36.07%) with the IOLMaster, and 51 eyes (13.53%) with the Aladdin. χ 2 analyses indicated a significant difference in failure rate between all 3 devices (P < .001). Logistic regression analysis highlighted a statistically significant trend of higher failure rates with increasing severity of nuclear, cortical, and posterior subcapsular cataracts. Bland-Altman statistics indicated small mean differences and narrow LoA (OA-2000 vs IOLMaster -0.09 to 0.08 mm; OA-2000 vs Aladdin -0.10 to 0.07 mm; IOLMaster vs Aladdin -0.05 to 0.04 mm). The OA-2000, a new SSOCT-based biometer, outperformed both the IOLMaster and Aladdin biometers in very advanced cataracts of various morphologies. The use of SSOCT technology may be the reason for the improved performance of the OA-2000 and may lead to this technology becoming the gold standard for the measurement of axial length. Copyright © 2016 Elsevier Inc. All rights reserved.

Evolution and coexistence of pollination ecotypes in an African Gladiolus (Iridaceae).

PubMed

Anderson, Bruce; Alexandersson, Ronny; Johnson, Steven D

2010-04-01

Pollinator-mediated selection has been suggested as a key driver of speciation in plants. We examined the potential role of hawkmoth pollinators in driving allopatric divergence and maintaining sympatric coexistence of morphotypes in the African iris Gladiolus longicollis. Floral tube length in this species varies from 35 mm to 130 mm across its geographic range and reflects the prevailing tongue lengths of local hawkmoth assemblages. The distribution of floral tube lengths is bimodal with two relatively discrete categories--long (about 90 mm) or short (about 50 mm)--that match the bimodal distribution of hawkmoth tongue lengths in eastern South Africa. At a contact site between these two floral morphs, we found few individuals of intermediate length, suggesting limited gene flow between morphs despite their interfertility. A difference in flowering phenology appears to be the main isolating barrier between morphs at this site. Long- and short-tubed morphs differed markedly in the chemical composition of their floral fragrance, a trait that could be used as a cue for morph-specific foraging by hawkmoths. Positive directional selection on tube length was found to occur in both morphs.

Minimally invasive sinus augmentation using ultrasonic piezoelectric vibration and hydraulic pressure: a multicenter retrospective study.

PubMed

Kim, Ji-Min; Sohn, Dong-Seok; Heo, Jeong-Uk; Park, Jun-Sub; Jung, Heui-Seung; Moon, Jee-Won; Lee, Ju-Hyoung; Park, In-Sook

2012-12-01

The purpose of this study was to evaluate the success rate of implants and vertical bone gain of edentulous posterior maxilla using ultrasonic piezoelectric vibration and hydraulic pressure, namely the hydrodynamic piezoelectric internal sinus elevation (HPISE) technique through a crestal approach. A total of 250 maxillary sinuses were augmented using HPISE and 353 implants (averaging 11.8 mm in length and 4.5 mm in diameter), with 12 different systems, were placed simultaneously with or without additional bone grafting. Plain radiograms and cone beam computed tomograms were taken in all patients to evaluate sinus augmentation. Membrane perforation was recorded at 10 of the 353 implant sites. The perforation rate was 2.83%. The total success rate of implantation was 97.2% after an average of 69.3 weeks of loading. The crestally approached sinus augmentation using ultrasonic piezoelectric vibration and hydraulic pressure is an additional method of maxillary sinus augmentation.

Macrozooplankton biomass in a warm-core Gulf Stream ring: Time series changes in size structure, taxonomic composition, and vertical distribution

NASA Astrophysics Data System (ADS)

Davis, Cabell S.; Wiebe, Peter H.

1985-01-01

Macrozooplankton size structure and taxonomic composition in warm-core ring 82B was examined from a time series (March, April, June) of ring center MOCNESS (1 m) samples. Size distributions of 15 major taxonomic groups were determined from length measurements digitized from silhouette photographs of the samples. Silhouette digitization allows rapid quantification of Zooplankton size structure and taxonomic composition. Length/weight regressions, determined for each taxon, were used to partition the biomass (displacement volumes) of each sample among the major taxonomic groups. Zooplankton taxonomic composition and size structure varied with depth and appeared to coincide with the hydrographic structure of the ring. In March and April, within the thermostad region of the ring, smaller herbivorous/omnivorous Zooplankton, including copepods, crustacean larvae, and euphausiids, were dominant, whereas below this region, larger carnivores, such as medusae, ctenophores, fish, and decapods, dominated. Copepods were generally dominant in most samples above 500 m. Total macrozooplankton abundance and biomass increased between March and April, primarily because of increases in herbivorous taxa, including copepods, crustacean larvae, and larvaceans. A marked increase in total macrozooplankton abundance and biomass between April and June was characterized by an equally dramatic shift from smaller herbivores (1.0-3.0 mm) in April to large herbivores (5.0-6.0 mm) and carnivores (>15 mm) in June. Species identifications made directly from the samples suggest that changes in trophic structure resulted from seeding type immigration and subsequent in situ population growth of Slope Water zooplankton species.

Effects of Salinity on the Habitat Selection and Growth Performance of Mediterranean Flathead Grey Mullet Mugil cephalus (Osteichthyes, Mugilidae)

NASA Astrophysics Data System (ADS)

Cardona, L.

2000-05-01

Flathead grey mullet (Mugil cephalus L. 1758) are commonly found in tropical and temperate estuaries. In spite of their ecological and economical importance, little is known about the effects of salinity on growth performance and habitat selection. Laboratory experiments revealed that the metabolic rate of young specimens was negatively affected by high salinity levels and that an improved growth performance was achieved in fresh water and oligohaline water. A stratified study on microhabitat use, carried out on the island of Minorca (Balearic archipelago), demonstrated that juvenile specimens, shorter than 200 mm (total length), concentrated all year round in fresh water or oligohaline sites. Mesohaline areas were usually avoided, except in summer. Immature fish, with a total length between 201 and 300 mm, show a similar pattern although in some seasons avoided freshwater sites. The habitat selection pattern of adults, i.e., fish longer than 301 mm, changed seasonally due to their offshore migration during the spawning season (from late summer to early winter). However, they usually showed a greater preference for polyhaline areas and strongly avoided freshwater sites. Euhaline areas were also avoided in autumn and summer. These results suggest that the young of this species are highly dependent on areas of low salinity and any factor which reduces the availability of such areas will, in turn, affect their fishery. Adults depend on polyhaline areas, although the avoidance of freshwater areas might be due to their shallowness. The situation might be different in some areas of the Indo-Pacific. These differences are discussed.

Lipid concentrations in Lake Michigan fishes: Seasonal, spatial, ontogenetic, and long-term trends

USGS Publications Warehouse

Madenjian, Charles P.; Elliott, Robert F.; DeSorcie, Timothy J.; Stedman, Ralph M.; O'Connor, Daniel V.; Rottiers, Donald V.

2000-01-01

Lipid concentrations were measured in seven species of fish from several locations in Lake Michigan during spring, summer, and fall in 1994 to 1995. Adult alewife (Alosa pseudoharengus) and age-2 coho salmon (Oncorhynchus kisutch) exhibited pronounced seasonal changes in lipid content. Adult alewives averaged 7.4% lipid, on a wet weight basis, during spring (May), 2.6% in summer (July), and 12.2% in fall (late September through October). Spring lipid concentration was low in age-2 coho salmon, averaging only 1.9%, then increased to 7.8% during summer and decreased to 4.5% by fall. In contrast, lipid content in adult bloater (Coregonus hoyi) was relatively constant with respect to season, ranging between 10.6% and 12.4% during the year. Lipid concentration increased with fish size for all species except rainbow smelt (Osmerus mordax). Although deepwater sculpin (Myoxocephalus thompsoni) were considerably larger than slimy sculpin (Cottus cognatus) (mean total length of 117 mm vs 68 mm), mean lipid content of deepwater sculpin (7.6%) was only slightly higher than that for slimy sculpin (6.6%). Comparison of lipid concentrations from this study with previous studies indicated that lipid concentration in lake trout (Salvelinus namaycush) and alewives in Lake Michigan did not change significantly from 1969–1971 to 1994–1995. Lipid concentration in large (about 250 mm total length) adult bloaters near Saugatuck (along the southeastern shore of the lake) decreased from 23.3% in 1980 to 11.9% in 1986, but showed no significant change between 1986 and 1994–1995.

Dissection and Exposure of the Whole Course of Deep Nerves in Human Head Specimens after Decalcification

PubMed Central

Liu, Longping; Arnold, Robin; Robinson, Marcus

2012-01-01

The whole course of the chorda tympani nerve, nerve of pterygoid canal, and facial nerves and their relationships with surrounding structures are complex. After reviewing the literature, it was found that details of the whole course of these deep nerves are rarely reported and specimens displaying these nerves are rarely seen in the dissecting room, anatomical museum, or atlases. Dissections were performed on 16 decalcified human head specimens, exposing the chorda tympani and the nerve connection between the geniculate and pterygopalatine ganglia. Measurements of nerve lengths, branching distances, and ganglia size were taken. The chorda tympani is a very fine nerve (0.44 mm in diameter within the tympanic cavity) and approximately 54 mm in length. The mean length of the facial nerve from opening of internal acoustic meatus to stylomastoid foramen was 52.5 mm. The mean length of the greater petrosal nerve was 26.1 mm and nerve of the pterygoid canal was 15.1 mm. PMID:22523494

[Comparative experiments of stripping sheep maxillary sinus mucosal with new-type stripper and umbrella detacher].

PubMed

Jiadong, Fan; Yanfeng, Li; Le, Liu; Yishi, Han; Pin, Hu; Yue, Zhang; Wenya, Bao

2016-10-01

To compare the stripping length obtained through the model of 0.012 and 0.014 of the nickel-titanium dual-stage maxillary sinus mucosa stripper, and the umbrella detacher. Twenty-four goats (1.5-2 years old) were chosen, randomly divided into A, B, C groups, each group of eight. Group A was 0.012 model group, group B was 0.014 model group, group C was umbrella detacher group. Animal model was established, and maxillary sinus mucosa was stripped to the left and right sides of the bottom of the sinus in three groups. The data was measured when stripping to the limit or being perforated. The average length of group A was 12.41 mm±4.35 mm, two cases perforated. The average length of group B was 23.38 mm±4.84 mm, one case perforated. The average length of group C was 2.61 mm±0.30 mm. The population mean of stripping length in three groups was not all the same calculated by analysis of variance (P<0.01). There were significant differences in the stripping length of the three groups by the SNK test (P<0.05). The nickel-titanium dual-stage maxillary sinus mucosa stripper can achieve a larger mucosal stripping range. The stripper with a model of 0.014 has a moderate flexibility and safety, and it can strip a large area of sinus mucosa.
.

Bond Strength of Composite CFRP Reinforcing Bars in Timber

PubMed Central

Corradi, Marco; Righetti, Luca; Borri, Antonio

2015-01-01

The use of near-surface mounted (NSM) fibre-reinforced polymer (FRP) bars is an interesting method for increasing the shear and flexural strength of existing timber members. This article examines the behaviour of carbon FRP (CFRP) bars in timber under direct pull-out conditions. The objective of this experimental program is to investigate the bond strength between composite bars and timber: bars were epoxied into small notches made into chestnut and fir wood members using a commercially-available epoxy system. Bonded lengths varied from 150 to 300 mm. Failure modes, stress and strain distributions and the bond strength of CFRP bars have been evaluated and discussed. The pull-out capacity in NSM CFRP bars at the onset of debonding increased with bonded length up to a length of 250 mm. While CFRP bar’s pull-out was achieved only for specimens with bonded lengths of 150 and 200 mm, bar tensile failure was mainly recorded for bonded lengths of 250 and 300 mm. PMID:28793423

Tag retention, growth, and survival of red swamp crayfish marked with a visible implant tag

USGS Publications Warehouse

Isely, J.J.; Stockett, P.E.

2001-01-01

Eighty juvenile (means: 42.4 mm total length, 1.6 g) red swamp crayfish Procambarus clarkii were implanted with sequentially numbered visible implant tags and held in the laboratory. Tags were injected transversely into the musculature just beneath the exoskeleton of the third abdominal segment from the cephalothorax; tags were visible upon inspection. An additional 20 crayfish were left untagged and served as controls. After 150 d, tag retention was 80% and all tags were readable. No tagged crayfish died during the study, and no differences in total length or weight were detected between tagged and control crayfish. All individuals molted at least three times during the 150-d study, and some individuals molted up to six times, suggesting that most tags would be permanently retained. The readability in the field without specialized equipment makes the visible implant tag ideal for studies of crayfish ecology, management, and culture.

A new species of Letheobia (Serpentes: Typhlopidae) from central Kenya.

PubMed

Malonza, Patrick K; Bauer, Aaron M; Ngwava, Jacob M

2016-03-20

A new species of blind snake in the genus Letheobia (L. mbeerensis sp. nov.) is described from the Mbeere area on the extreme lower slopes of southeastern Mt. Kenya. It is an attenuate blind snake, superficially similar to Letheobia lumbriciformis but with 20 midbody scale rows and 670 middorsal scales. It has a total length of 280 mm with the proportionally longest tail in the genus (2.9% of total length), a broad rostral, eyes barely visible and in life it is pink in color. The new species is known from only a single specimen collected at Siakago, in Mbeere-Embu, which lies at an elevation of about 1200m. It is a burrowing species and like many other blind snakes it is likely to be nocturnal and rarely encountered on the soil surface. The new species is incorporated into a key to the scolecophidian snakes of Kenya.

[Effects of mulching management of Phyllostachys heterocycla forests on the characteristics of soil infiltration and biometrics in southwest Zhejiang Province, China].

PubMed

Wang, Yi Kun; Jin, Ai Wu; Fang, Sheng Zuo

2017-05-18

Soil infiltration, soil physical and chemical properties, root length density and soil fauna diversity were studied in Phyllostachys heterocycla forests with different mulching times in southwest Zhejiang Province, China. Significant differences of soil infiltration capability were found among the forests with different mulching times and among soil layers. Soil infiltration capability generally declined in the deeper soil layers. With mulching management, soil infiltration capability increased under the first mulching, and then declined with the increase of mulching times. The Kostiakov model was suitable for simulating soil infiltration process. With the extending of mulching times (4 to 6 years), soil pH and total/non-capillary porosity decreased, while soil bulk density, soil orga-nic matter and total nitrogen contents increased significantly. Soil initial, steady, and average infiltration rates as well as the cumulative infiltration amount correlated closely with the length density of roots with diameter from 0.5 mm to 5.0 mm, showing a decreasing tendency with the decrease in root length density. Soil fauna density was highest in the forest under the first mulching, and was lowest after third mulching. The decreased numbers of large and meso-arthropods, including Symphyla, Chilopoda, Diplopoda, Hymenoptera and pseudoscorpions, and the micro-arthropods, including Oribatida, Mesostigmata, Onychiuridae, Neanuridae, Cyphoderidae, and Entomobryidae, showed negative effects on soil infiltration. In conclusion, long-term mulching changed soil physical and chemical properties, decreased soil infiltration capability, and suppressed the development of soil fauna, which might cause the decline ofP. heterocycla forests.

Leg lengthening and femoral-offset reduction after total hip arthroplasty: where is the problem - stem or cup positioning?

PubMed

Al-Amiry, Bariq; Mahmood, Sarwar; Krupic, Ferid; Sayed-Noor, Arkan

2017-09-01

Background Restoration of femoral offset (FO) and leg length is an important goal in total hip arthroplasty (THA) as it improves functional outcome. Purpose To analyze whether the problem of postoperative leg lengthening and FO reduction is related to the femoral stem or acetabular cup positioning or both. Material and Methods Between September 2010 and April 2013, 172 patients with unilateral primary osteoarthritis treated with THA were included. Postoperative leg-length discrepancy (LLD) and global FO (summation of cup and FO) were measured by two observers using a standardized protocol for evaluation of antero-posterior plain hip radiographs. Patients with postoperative leg lengthening ≥10 mm (n = 41) or with reduced global FO >5 mm (n = 58) were further studied by comparing the stem and cup length of the operated side with the contralateral side in the lengthening group, and by comparing the stem and cup offset of the operated side with the contralateral side in the FO reduction group. We evaluated also the inter-observer and intra-observer reliability of the radiological measurements. Results Both observers found that leg lengthening was related to the stem positioning while FO reduction was related to the positioning of both the femoral stem and acetabular cup. Both inter-observer reliability and intra-observer reproducibility were moderate to excellent (intra-class correlation co-efficient, ICC ≥0.69). Conclusion Post THA leg lengthening was mainly caused by improper femoral stem positioning while global FO reduction resulted from improper positioning of both the femoral stem and the acetabular cup.

Lateral column length in adult flatfoot deformity.

PubMed

Kang, Steve; Charlton, Timothy P; Thordarson, David B

2013-03-01

In adult acquired flatfoot deformity, it is unclear whether the lateral column length shortens with progression of the deformity, whether it is short to begin with, or whether it is short at all. To our knowledge, no previous study has examined the lateral column length of patients with adult acquired flatfoot deformity compared to a control population. The purpose of our study was to compare the lateral column length in patients with and without adult acquired flatfoot deformity to see if there was a significant difference. The study was a retrospective radiographic review of 2 foot and ankle fellowship-trained orthopaedic surgeons' patients with adult flatfoot deformity. Our study population consisted of 75 patients, 85 feet (28 male, 57 female) with adult flatfoot deformity with a mean age of 64 (range, 23-93). Our control population consisted of 57 patients and 70 feet (23 male, 47 female) without flatfoot deformity with a mean age of 61 (range, 40-86 years). Weightbearing anteroposterior (AP) and lateral foot radiographs were analyzed for each patient, and the following measurements were made: medial and lateral column lengths, talonavicular uncoverage angle, talus-first metatarsal angle, calcaneal pitch angle, and medial and lateral column heights. An unpaired t test was used to analyze the measurements between the groups. Ten patients' radiographs were remeasured, and correlation coefficients were obtained to assess the reliability of the measuring techniques. For the flatfoot group, the mean medial and lateral column lengths on the AP radiograph were 108.6 mm and 95.8 mm, respectively; the mean talo-navicular uncoverage angle was 26.2 degrees; and the mean talus-first metatarsal angle was 20.0 degrees. In the control group, the mean medial and lateral column lengths on the AP radiograph were 108.8 mm and 96.5 mm, respectively; the mean talo-navicular uncoverage angle was 8.2 degrees; and the mean talus-first metatarsal angle was 7.7 degrees. On the lateral radiograph in the flatfoot group, the mean medial and lateral column lengths were 167.2 mm and 166.6 mm, respectively; the mean medial and lateral column heights were 16.0 mm and 14.7 mm, respectively; the mean calcaneal pitch angle was 15.6 degrees; and the talus-first metatarsal angle was 10.3 degrees and for the control group, the mean medial and lateral column lengths were 165.3 mm and 163.5 mm, respectively; the mean medial and lateral column heights were 22.8 mm and 13.1 mm, respectively; the mean calcaneal pitch angle was 22.4 degrees; and the talus-first metatarsal angle was -3.6 degrees. None of the differences in measurements for medial and lateral column lengths between the flatfoot and control groups achieved statistical significance. However, statistically significant differences between the 2 groups were observed in the measurements for medial and lateral column heights, talo-navicular uncoverage angle, calcaneal pitch angle, and talus-first metatarsal angle. There is no difference in lateral column lengths between patients with and without adult flatfoot deformity. The perceived shortened lateral column is likely due to forefoot abduction and hindfoot valgus deformities that are associated with adult flatfoot deformity. Level III, comparative series.

The control effect of orthokeratology on axial length elongation in Chinese children with myopia.

PubMed

Zhu, Meng-Jun; Feng, Hao-Yan; He, Xian-Gui; Zou, Hai-Dong; Zhu, Jian-Feng

2014-11-24

To retrospectively compare axial elongation in children with different degrees of myopia wearing spectacles and undergoing ortho-k treatment. The medical records of 128 patients who were fitted with spectacles or orthokeratology (ortho-k) lenses in our clinic between 2008 and 2009 were reviewed. Ortho-k group comprised 65 subjects and 63 subjects wearing spectacles were included in the control group. Subjects were also divided into low-myopia, moderate-myopia and high-myopia groups, based on the basic spherical equivalent refractive error. Axial length periodically measured over 2-year of lens wear and changes in axial length were compared between treatment groups and between subgroups with different degrees of myopia. The control group exhibited more changes in axial length than the ortho-k group at both 12 months (0.39 ± 0.21 mm vs 0.16 ± 0.17 mm, p <0.001) and 24 months (0.70 ± 0.35 mm vs 0.34 ± 0.29 mm, p <0.001). Axial length elongation was estimated to be slower by about 51% in the ortho-k group. Similar results were found for the subgroups (49%, 59% and 46% reductions, respectively). In the group with low and moderate myopia, the annual increases in axial length were significantly different between the ortho-k and control groups during both the first ( Low myopia: 0.19 ± 0.17 mm vs 0.40 ± 0.18 mm, p = 0.001; Moderate myopia: 0.14 ± 0.18 mm vs 0.45 ± 0.22 mm, p <0.001) and second ( Low myopia: 0.18 ± 0.14 mm vs 0.32 ± 0.19 mm, p = 0.012; Moderate myopia: 0.18 ± 0.16 mm vs 0.34 ± 0.30 mm, p = 0.030) years. In the high myopia groups, significant differences were only found between the ortho-k and control groups during the first year (0.16 ± 0.18 mm vs 0.34 ± 0.22 mm, p = 0.004). The 2-year axial elongation was significantly associated with initial age (p <0.001) and treatment (p <0.001), but not with gender, initial refractive error, initial axial length, initial corneal curvature. This 2-year study indicates that ortho-k contact lens wear is effective for reducing myopia progression in children with low, moderate and high myopia.

Reproductive development in the sicklefin chub in the Missouri and Lower Yellowstone Rivers

USGS Publications Warehouse

Dieterman, Douglas J.; Roberts, Eric; Braaten, Patrick J.; Galat, David L.

2006-01-01

We describe aspects of sicklefin chub (Macrhybopsis meeki) reproductive development from three study areas encompassing greater than 2,700 km of the Missouri and Lower Yellowstone rivers. The sicklefin chub was collected between late July and early October in 1996 and 1997. A total of 193 sicklefin chub was collected and examined for reproductive characteristics. Twenty-nine sicklefin chub were found to be reproductively mature females. Some sicklefin chub matured at age 2, but most matured at age 3 and all matured by age 4. Females first became mature at 70 to 79 mm total length (TL) in the Upper Missouri River reach in central Montana, 80 to 89 mm TL in the Missouri and Lower Yellowstone rivers in eastern Montana-western North Dakota, and 90 to 99 mm TL in the lower Missouri River in Nebraska, Iowa, Kansas, and Missouri. Gonad mass of gravid females averaged 6.9% of total body mass and ranged from 1.7 to 13.5%. Total number of oocytes per female, ranged from 7 to 1,561. Reproductive development of the sicklefin chub appeared to be group synchronous or synchronous indicating multiple spawnings during a spawning season. This variability in spawning mode required cautious interpretation of gonadosomatic index values and oocyte counts as estimates of total fecundity, because some females might have released a cohort of oocytes prior to their capture.

Effects of replacing maize silage with lucerne silage and lucerne silage chop length on rumen function and milk fatty acid composition.

PubMed

Thomson, A L; Humphries, D J; Kliem, K E; Dittmann, M T; Reynolds, C K

2017-09-01

The objective of this study was to investigate whether higher lucerne (Medicago sativa; alfalfa) silage inclusion rate and longer lucerne chop length improves rumen function through increased provision of physically effective fiber, when included in a maize and lucerne silage-based total mixed ration. Diets were formulated to contain a 50:50 forage:concentrate ratio [dry matter (DM) basis] and be isonitrogenous and contain equal levels of neutral detergent fiber (320 g/kg). The forage portion of the offered diets was composed of maize and lucerne silage DM in proportions (wt/wt) of either 25:75 (high lucerne; HL) or 75:25 (low lucerne; LL). Second-cut lucerne was harvested and conserved as silage at either a long (L) or a short (S) chop length (geometric mean particle lengths of 9.0 and 14.3 mm, respectively). These variables were combined in a 2 × 2 factorial arrangement to give 4 treatments (HLL, HLS, LLL, LLS), which were fed in a 4 × 4 Latin square design study to 4 rumen-cannulated, multiparous, Holstein dairy cows in mid lactation. Effects on DM intake, chewing behavior, rumen volatile fatty acid concentration, rumen pH, rumen and fecal particle size, milk production, and milk fatty acid profile were measured. Longer chop length increased rumination times per kilogram of DM intake (+2.8 min/kg) relative to the S chop length, with HLL diets resulting in the most rumination chews. Rumen concentrations of total volatile fatty acids, acetate, and n-valerate were higher for the HLS diet than the other 3 diets, whereas rumen propionate concentration was lowest for the HLL diet. Physically effective fiber (particles >4 mm) percentage in the rumen mat was increased when L chop length was fed regardless of lucerne inclusion rate. No effect of treatment was observed for milk yield, although milk protein concentration was increased by L for the LL diet (+1.6 g/kg) and decreased by L for the HLL diet (-1.4 g/kg). Milk fat concentrations of total cis-18:1 (+3.7 g/100 g of fatty acids) and 18:3 n-3 (+0.2 g/100 g of fatty acids) were greater with HL. In conclusion, longer lucerne silage chop length increased time spent ruminating per kilogram of DM intake, but had no effect on rumen pH in the present study. Increasing dietary lucerne inclusion rate had no effects on rumination activity or rumen pH, but decreased the ratio of n-6:n-3 polyunsaturated fatty acid concentrations in milk fat. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Vulnerability of Quick Disconnect Connectors to Carbon Fibers

NASA Technical Reports Server (NTRS)

Meyers, J. A.

1979-01-01

Unprotected quick disconnect electrical connectors were exposed to fibers of 3mm, 7mm, and 12mm lengths. The average exposure to failure was determined. Results indicate that when the fiber length divided by the airgap is less than one, multiple fibers are required to bridge the gap, and the exposure time to failure rises rapidly.

Transfer and development length of 15.2 mm (0.6 in.) diameter prestressing strand in high performance concrete : results of the Hoblitzell-Buckner beam tests

DOT National Transportation Integrated Search

1995-06-01

This study examines the transfer and development length of 15.2 mm (0.6 in.) diameter prestressing strand in high performance (high strength) concrete. Two 1067 mm (42.0 in.) deep rectangular beams, commonly called the Hoblitzell-Buckner beams, each ...

Association of Axial Length With Risk of Uncorrectable Visual Impairment for Europeans With Myopia.

PubMed

Tideman, J Willem L; Snabel, Margaretha C C; Tedja, Milly S; van Rijn, Gwyneth A; Wong, King T; Kuijpers, Robert W A M; Vingerling, Johannes R; Hofman, Albert; Buitendijk, Gabriëlle H S; Keunen, Jan E E; Boon, Camiel J F; Geerards, Annette J M; Luyten, Gregorius P M; Verhoeven, Virginie J M; Klaver, Caroline C W

2016-12-01

Myopia (ie, nearsightedness) is becoming the most common eye disorder to cause blindness in younger persons in many parts of the world. Visual impairment due to myopia is associated with structural changes of the retina and the globe because of elongation of the eye axis. How axial length-a sum of the anterior chamber depth, lens thickness, and vitreous chamber depth-and myopia relate to the development of visual impairment over time is unknown. To evaluate the association between axial length, spherical equivalent, and the risk of visual impairment and to make projections of visual impairment for regions with high prevalence rates. This cross-sectional study uses population-based data from the Rotterdam Study I (1990 to 1993), II (2000 to 2002), and III (2006 to 2008) and the Erasmus Rucphen Family Study (2002 to 2005) as well as case-control data from the Myopia Study (2010 to 2012) from the Netherlands. In total, 15 404 individuals with data on spherical equivalent and 9074 individuals with data on axial length were included in the study; right eyes were used for analyses. Data were analyzed from September 2014 to May 2016. Visual impairment and blindness (defined according to the World Health Organization criteria as a visual acuity less than 0.3) and predicted rates of visual impairment specifically for persons with myopia. Of the 15 693 individuals included in this study, the mean (SD) age was 61.3 (11.4) years, and 8961 (57.1%) were female. Axial length ranged from 15.3 to 37.8 mm; 819 individuals had an axial length of 26 mm or greater. Spherical equivalent ranged from -25 to +14 diopters; 796 persons had high myopia (ie, a spherical equivalent of -6 diopters or less). The prevalence of visual impairment varied from 1.0% to 4.1% in the population-based studies, was 5.4% in the Myopia Study, and was 0.3% in controls. The prevalence of visual impairment rose with increasing axial length and spherical equivalent, with a cumulative incidence (SE) of visual impairment of 3.8% (1.3) for participants aged 75 years with an axial length of 24 to less than 26 mm and greater than 90% (8.1) with an axial length of 30 mm or greater. The cumulative risk (SE) of visual impairment was 5.7% (1.3) for participants aged 60 years and 39% (4.9) for those aged 75 years with a spherical equivalent of -6 diopters or less. Projections of these data suggest that visual impairment will increase 7- to 13-fold by 2055 in high-risk areas. This study demonstrated that visual impairment is associated with axial length and spherical equivalent and may be unavoidable at the most extreme values in this population. Developing strategies to prevent the development of myopia and its complications could help to avoid an increase of visual impairment in the working-age population.

An ultrashort throw ratio projection lens design based on a catadioptric structure

NASA Astrophysics Data System (ADS)

Wang, Hsiu-Cheng; Pan, Jui-Wen

2018-07-01

In this paper, we present a rotational symmetry for an ultrashort throw (UST) lens with offset field. The UST lens has a throw ratio of 0.23 and a total track of 195 mm. The optical elements of the UST lens are comprised of two parts. First, a catadioptric projection lens where the catadioptric function permits reaching an ultrashort throw ratio, short total track, while at the same time requiring fewer lens elements. The second part is a collimating lens which takes advantage of the telecentric condition to generate uniform total internal reflection (TIR) in the TIR prism. With this design, an effective focal length of -1.96 mm and a f-number of 2.4 can be obtained. The root mean square spot size and lateral colour of all fields are smaller than one pixel in size. The maximum optical distortion of -0.97% and TV distortion of 0.2% are acceptable. In terms of image quality, the modulation transfer function (MTF) values for all fields are above 0.65 at 0.245 line pairs/mm. Even when the tolerance error is considered, the MTF values for all fields are still above 0.3. The suitability of the novel UST lens design for projection applications is discussed.

Relation between Kidney Length and Cardiovascular and Renal Risk in High-Risk Patients

PubMed Central

van der Sande, Nicolette G.C.; Visseren, Frank L.J.; van der Graaf, Yolanda; Nathoe, Hendrik M.; de Borst, Gert Jan; Leiner, Tim

2017-01-01

Background and objectives Kidney length is often measured during routine abdominal ultrasonography and may be of use to identify patients at high vascular and renal risk. We aimed to explore patient characteristics related to kidney length, from which reference values were derived, and evaluate the relationship between kidney length and the risk of cardiovascular events and ESRD in high-risk patients. Design, setting, participants, & measurements The study population consisted of 10,251 patients with clinical manifest arterial disease or vascular risk factors included in the Second Manifestations of ARTerial disease (SMART) Study cohort between 1996 and 2014. Linear regression was used to explore patient characteristics of kidney length. The relationship between kidney length and cardiovascular events (myocardial infarction, stroke, and cardiovascular mortality), all-cause mortality, and ESRD was analyzed using Cox regression. Kidney length was analyzed in tertiles, using the second tertile as the reference category. Results Kidney length was strongly correlated with body surface area (2.04 mm; 95% confidence interval [95% CI], 1.95 to 2.13 per 0.1 m2 increase) and eGFR (1.62 mm; 95% CI, 1.52 to 1.73 per 10 ml/min per 1.73 m2 increase). During the median follow-up of 6.3 years, 1317 patients experienced a cardiovascular event, including 711 myocardial infarctions, 369 strokes, and 735 vascular cause deaths. A total of 1462 patients died of any cause and 52 patients developed ESRD. Irrespective of eGFR, patients in the third tertile of kidney length (11.7–16.1 cm) were at higher risk of cardiovascular mortality (hazard ratio, 1.33; 95% CI, 1.05 to 1.67) and cardiovascular events (hazard ratio, 1.28; 95% CI, 1.09 to 1.50). Patients in the first tertile of kidney length (7.8–10.8 cm) were not at higher risk of cardiovascular adverse events. Conclusions Large kidney length is related to higher risk of cardiovascular events and mortality in high-risk patients, irrespective of eGFR. Kidney length may serve as a clinical marker to further identify patients at high cardiovascular risk. PMID:28487344

Relation between Kidney Length and Cardiovascular and Renal Risk in High-Risk Patients.

PubMed

van der Sande, Nicolette G C; Visseren, Frank L J; van der Graaf, Yolanda; Nathoe, Hendrik M; de Borst, Gert Jan; Leiner, Tim; Blankestijn, Peter J

2017-06-07

Kidney length is often measured during routine abdominal ultrasonography and may be of use to identify patients at high vascular and renal risk. We aimed to explore patient characteristics related to kidney length, from which reference values were derived, and evaluate the relationship between kidney length and the risk of cardiovascular events and ESRD in high-risk patients. The study population consisted of 10,251 patients with clinical manifest arterial disease or vascular risk factors included in the Second Manifestations of ARTerial disease (SMART) Study cohort between 1996 and 2014. Linear regression was used to explore patient characteristics of kidney length. The relationship between kidney length and cardiovascular events (myocardial infarction, stroke, and cardiovascular mortality), all-cause mortality, and ESRD was analyzed using Cox regression. Kidney length was analyzed in tertiles, using the second tertile as the reference category. Kidney length was strongly correlated with body surface area (2.04 mm; 95% confidence interval [95% CI], 1.95 to 2.13 per 0.1 m 2 increase) and eGFR (1.62 mm; 95% CI, 1.52 to 1.73 per 10 ml/min per 1.73 m 2 increase). During the median follow-up of 6.3 years, 1317 patients experienced a cardiovascular event, including 711 myocardial infarctions, 369 strokes, and 735 vascular cause deaths. A total of 1462 patients died of any cause and 52 patients developed ESRD. Irrespective of eGFR, patients in the third tertile of kidney length (11.7-16.1 cm) were at higher risk of cardiovascular mortality (hazard ratio, 1.33; 95% CI, 1.05 to 1.67) and cardiovascular events (hazard ratio, 1.28; 95% CI, 1.09 to 1.50). Patients in the first tertile of kidney length (7.8-10.8 cm) were not at higher risk of cardiovascular adverse events. Large kidney length is related to higher risk of cardiovascular events and mortality in high-risk patients, irrespective of eGFR. Kidney length may serve as a clinical marker to further identify patients at high cardiovascular risk. Copyright © 2017 by the American Society of Nephrology.

Stereological and Morphometric Analysis of MRI Chiari Malformation Type-1

PubMed Central

Alkoç, Ozan Alper; Songur, Ahmet; Eser, Olcay; Toktas, Muhsin; Esi, Ertap; Haktanir, Alpay

2015-01-01

Objective In this study, we aimed to investigate the underlying ethiological factors in chiari malformation (CM) type-I (CMI) via performing volumetric and morphometric length-angle measurements. Methods A total of 66 individuals [33 patients (20-65 years) with CMI and 33 control subjects] were included in this study. In sagittal MR images, tonsillar herniation length and concurrent anomalies were evaluated. Supratentorial, infratentorial, and total intracranial volumes were measured using Cavalieri method. Various cranial distances and angles were used to evaluate the platybasia and posterior cranial fossa (PCF) development. Results Tonsillar herniation length was measured 9.09±3.39 mm below foramen magnum in CM group. Tonsillar herniation/concurrent syringomyelia, concavity/defect of clivus, herniation of bulbus and fourth ventricle, basilar invagination and craniovertebral junction abnormality rates were 30.3, 27, 18, 2, 3, and 3 percent, respectively. Absence of cisterna magna was encountered in 87.9% of the patients. Total, IT and ST volumes and distance between Chamberlain line and tip of dens axis, Klaus index, clivus length, distance between internal occipital protuberance and opisthion were significantly decreased in patient group. Also in patient group, it was found that Welcher basal angle/Boogard angle increased and tentorial slope angle decreased. Conclusion Mean cranial volume and length-angle measurement values significantly decreased and there was a congenital abnormality association in nearly 81.5 percent of the CM cases. As a result, it was concluded that CM ethiology can be attributed to multifactorial causes. Moreover, congenital defects can also give rise to this condition. PMID:26713146

Continuous D-tagatose production by immobilized thermostable L-arabinose isomerase in a packed-bed bioreactor.

PubMed

Ryu, Se-Ah; Kim, Chang Sup; Kim, Hye-Jung; Baek, Dae Heoun; Oh, Deok-Kun

2003-01-01

D-Tagatose was continuously produced using thermostable L-arabinose isomerase immobilized in alginate with D-galactose solution in a packed-bed bioreactor. Bead size, L/D (length/diameter) of reactor, dilution rate, total loaded enzyme amount, and substrate concentration were found to be optimal at 0.8 mm, 520/7 mm, 0.375 h(-1), 5.65 units, and 300 g/L, respectively. Under these conditions, the bioreactor produced about 145 g/L tagatose with an average productivity of 54 g tagatose/L x h and an average conversion yield of 48% (w/w). Operational stability of the immobilized enzyme was demonstrated, with a tagatose production half-life of 24 days.

Prevalence of the parasitic copepod Haemobaphes intermedius on juvenile buffalo sculpins from Washington State

USGS Publications Warehouse

Halpenny, C.M.; Kocan, R.M.; Hershberger, P.K.

2004-01-01

The parasitic copepod, Haemobaphes intermedius, was detected in 62% of juvenile buffalo sculpins Enophrys bison, a previously unreported host, from the San Juan Islands archipelago in Washington State. Most infestations were characterized by the presence of a single female copepod infestations with multiple H. intermedius occurred either unilaterally or bilaterally in 29% of parasitized individuals. Impaired condition of parasitized hosts was indicated by significantly lower total lengths and weights (34.9 mm; 1.6 g) than in unparasitized cohorts (38.9 mm; 2.1 g). Host specificity was indicated by the failure to detect H. intermedius in 43 sympatric great sculpins Myoxocephalus polyacanthocephalus from the same location.

The Royal College of Ophthalmologists' National Ophthalmology Database Study of cataract surgery: report 2, relationships of axial length with ocular copathology, preoperative visual acuity, and posterior capsule rupture

PubMed Central

Day, A C; Donachie, P H J; Sparrow, J M; Johnston, R L

2015-01-01

Purpose To describe the relationships of axial length with ocular copathology, preoperative visual acuity, and posterior capsule rupture rates in patients undergoing cataract surgery. Design The Royal College of Ophthalmologists' National Ophthalmology Database (NOD) study. Methods Anonymised data on 180 114 eyes from 127 685 patients undergoing cataract surgery between August 2006 and November 2010 were collected prospectively from 28 sites. Data parameters included: demographics, biometry, ocular copathology, visual acuity measurements, and surgical complications including posterior capsule rupture, or vitreous loss or both (PCR). Results Consultant surgeons performed a higher proportion of operations on eyes whose axial length were at the extremes. Glaucoma and age related macular degeneration were more common in eyes with shorter axial lengths, whilst previous vitrectomy was associated with longer axial lengths. Eyes with brunescent or white cataracts or amblyopia were more common at both axial length extremes. Preoperative visual acuities were similar for eyes with axial length measurements up to approximately 28 mm and worse for eyes with longer axial length measurements. PCR rates showed little change with axial length (overall mean 1.95%, 95% CI: 1.89 to 2.01%), except for a borderline increase in eyes with axial length <20.0 mm where rates were 3.6% (95% CI: 2.0 to 6.3%). The likelihood of PCR in eyes with axial length <20.0 mm was 1.88 times higher than those of ≥20.0 mm (P=0.0373). Conclusion Rates of ocular comorbidities vary by axial length. PCR rates in eyes with very short or long axial lengths were lower than expected. PMID:26493034

[Comparison of anorectal pressure after procedure for prolapse and hemorrhoids versus Doppler-guided hemorrhoidal artery ligation for grade III hemorrhoids].

PubMed

Dong, Xiao-ni; Tang, Ying-chun

2013-12-01

To compare the long-term anorectal manometry of patients with grade III hemorrhoids treated by procedure for prolapse and hemorrhoids (PPH) or Doppler-guided hemorrhoidal artery ligation (DGHAL). A total of 114 patients with grade III hemorrhoids in our department in 2010 were prospectively enrolled, and divided into PPH group (63 cases) and DGHAL group (51 cases) according to patient preference. Patients received anorectal pressure examination 2, 6, 12, 18 months after operation, including rectal resting pressure, anal resting pressure, maximal anal contractive pressure and length of high-pressure band. Anorectal manometries between two procedure groups were compared. In every time point of follow-up, as compared to PPH group, DGHAL group presented higher anal resting pressure[postoperative 2 months: (56.2±2.6) mmHg vs. (43.2±3.1) mmHg, postoperative 6 months: (55.2±2.1) mmHg vs. (45.1±2.5) mmHg, postoperative 12 months: (53.2±3.0) mmHg vs. (40.2±3.2) mmHg, postoperative 18 months: (55.3±2.6) mmHg vs. (43.2±2.5) mmHg, all P<0.01], and longer length of high-pressure band [postoperative 2 months: (3.45±0.14) cm vs. (2.95±0.22) cm, postoperative 6 months: (3.46±0.12) cm vs. (2.94±0.26) cm, postoperative 12 months: (3.45±0.12) cm vs. (3.01±0.21) cm, postoperative 18 months: (3.56±0.12) cm vs. (3.02±0.23) cm, all P<0.01]. While no significant differences of maximal anal contractive pressure and rectal resting pressure were found between the two groups. Both PPH and DGHAL are safe procedures and have similar efficacy in the treatment of grade III hemorrhoids, while DGHALpossesses better efficacy in the time of anal function recovery and the maintenance of anal function.

Retrospective analysis of survival rates and marginal bone loss on short implants in the mandible.

PubMed

Draenert, Florian G; Sagheb, Keyvan; Baumgardt, Katharina; Kämmerer, Peer W

2012-09-01

Short implants have become an interesting alternative to bone augmentation in dental implantology. Design of shorter implants and longer surveillance times are a current research issue. The goal of this study was to show the survival rates of short implants below 9 mm in the partly edentulous mandibular premolar and molar regions with fixed prosthetics. Marginal vertical and 2D bone loss was evaluated additionally. Different implant designs are orientationally evaluated. A total of 247 dental implants with fixed prosthetics (crowns and bridges) in the premolar and molar region of the mandible were evaluated; 47 implants were 9 mm or shorter. Patient data were evaluated to acquire implant survival rates, implant diameter, gender and age. Panoramic X-rays were analysed for marginal bone loss. Average surveillance time was 1327 days. Cumulative survival rate (CSR) of short implants was 98% (1 implants lost) compared to 94% in the longer implants group without significance. Thirty-five of the short implants were Astratech (0 losses) and 12 were Camlog Screw Line Promote Plus (1 loss). Early vertical and two-dimensional marginal bone loss was not significantly different in short and regular length implant group with an average of 0.6 mm and 0.7 mm(2) in short implants over the observation period. Within the limitations of this study, we conclude that short implants with a length of 9 mm or less have equal survival rates compared with longer implants over the observation period of 1-3 years. © 2011 John Wiley & Sons A/S.

Radiofrequency ablation of the pancreas with and without intraluminal duodenal cooling in a porcine model.

PubMed

Fegrachi, Samira; Molenaar, I Quintus; Klaessens, John H; Besselink, Marc G; Offerhaus, Johan A; van Hillegersberg, Richard

2013-10-01

To determine the short-term outcome of radiofrequency ablation (RFA) of pancreatic tissue near the duodenum and portomesenteric vessels (PMV) in a porcine model with and without intraluminal duodenal cooling. RFA has been proposed as a new treatment strategy in patients with unresectable locally advanced pancreatic cancer. RFA may cause thermal damage to the duodenum and vascular structures, but these risks and potential protective measures have never been systematically addressed. Intraluminal duodenal cooling during RFA could prevent thermal damage to the duodenum. RFA was performed in 11 pigs during laparotomy with a bipolar probe of 30 mm active length at a power of 30 W until a total energy of 15 kJ was administered. The RFA probe was inserted in the pancreas at 5 or 15 mm from the duodenum, PMV, and in the pancreatic tail. RFA near the duodenum was performed with and without intraluminal duodenal cooling using 100 mL/min saline of 5°C. Histopathologic assessment was performed. The maximum RFA-induced temperature was 92°C. RFA with one single probe induced adequate ablation lesions with a diameter of 20 mm over a length of 30 mm. Without duodenal cooling, RFA induced duodenal thermal damage, whereas with duodenal cooling, no damage was observed. RFA at 15 mm from the PMV resulted in minimal superficial focal vascular damage, without thrombosis or hemorrhage. RFA provides adequate ablation zones in the pancreas of the porcine. Thermal damage to the duodenum can be prevented by intraluminal duodenal cooling without loss of ablation effectivity. Copyright © 2013 Elsevier Inc. All rights reserved.

Biometric analysis of the clinical crown and the width/length ratio in the maxillary anterior region.

PubMed

Orozco-Varo, Ana; Arroyo-Cruz, Gema; Martínez-de-Fuentes, Rafael; Jiménez-Castellanos, Emilio

2015-06-01

Restorative dentistry often involves correcting tooth size discrepancies. Therefore, dental biometrics should play an important role in the planning of an esthetic restoration. The purpose of this study was to analyze the clinical crown width, length, and width/length ratio of maxillary central incisors, lateral incisors, and canines in an adult population. The study also aimed to determine whether a correlation exists between natural tooth dimensions and the optimal tooth dimension guidelines suggested for planning esthetic restorations. Stone casts were poured from irreversible hydrocolloid impressions of 412 healthy adult participants. These casts were used to measure the maximum mesiodistal width and maximum crown-root length of the maxillary central incisors, lateral incisors, and canines with a digital precision caliper (0.01 mm). The width/length ratio was calculated for each tooth, and 40 casts were selected to test the reliability of the measuring method. The mean age of the participants in the sample was 33.94 years; 60.7% were women and 39.3% were men. The mean width value was 8.71 mm for central incisors, 6.75 mm for lateral incisors, and 7.81 mm for canines. The mean length was 10.23 mm for central incisors, 8.59 mm for lateral incisors, and 9.93 mm for canines. The average width/length ratio was 85% for central incisors and 79% for lateral incisors and canines. The data obtained from the population studied are similar to those from previous research studies with similar methodology. However, great discrepancies in the absolute values were found when compared with other studies of ideal tooth dimension guidelines on the personal preferences and the esthetic perception of dentists. The perception of what is considered natural seems to differ from what is considered esthetically perfect. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Analysis of human acellular nerve allograft reconstruction of 64 injured nerves in the hand and upper extremity: a 3 year follow-up study.

PubMed

Zhu, Shuang; Liu, Jianghui; Zheng, Canbin; Gu, Liqiang; Zhu, Qingtang; Xiang, Jianping; He, Bo; Zhou, Xiang; Liu, Xiaolin

2017-08-01

Human acellular nerve allografts have been increasingly applied in clinical practice. This study was undertaken to investigate the functional outcomes of nerve allograft reconstruction for nerve defects in the upper extremity. A total of 64 patients from 13 hospitals were available for this follow-up study after nerve repair using human acellular nerve allografts. Sensory and motor recovery was examined according to the international standards for motor and sensory nerve recovery. Subgroup analysis and logistic regression analysis were conducted to identify the relationship between the known factors and the outcomes of nerve repair. Mean follow-up time was 355 ± 158 (35-819) days; mean age was 35 ± 11 (14-68) years; average nerve gap length was 27 ± 13 (10-60) mm; no signs of infection, tissue rejection or extrusion were observed among the patients; 48/64 (75%) repaired nerves experienced meaningful recovery. Univariate analysis showed that site and gap length significantly influenced prognosis after nerve repair using nerve grafts. Delay had a marginally significant relationship with the outcome. A multivariate logistic regression model revealed that gap length was an independent predictor of nerve repair using human acellular nerve allografts. The results indicated that the human acellular nerve allograft facilitated safe and effective nerve reconstruction for nerve gaps 10-60 mm in length in the hand and upper extremity. Factors such as site and gap length had a statistically significant influence on the outcomes of nerve allograft reconstruction. Gap length was an independent predictor of nerve repair using human acellular nerve allografts. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ivanyushenkov, Y.; Doose, C.; Fuerst, J.

Development of superconducting undulator (SCU) technology continues at the Advanced Photon Source (APS). The experience of building and successful operating the first short-length, 16-mm period length superconducting undulator SCU0 paved the way for a 1-m long, 18-mm period device— SCU18-1— which has been in operation since May 2015. The APS SCU team has also built and tested a 1.5-m long, 21-mm period length undulator as a part of the LCLS SCU R&D program, aimed at demonstration of SCU technology availability for free electron lasers. This undulator successfully achieved all the requirements including a phase error of 5° RMS. Our teammore » has recently completed one more 1-m long, 18-mm period length undulator— SCU18-2— that is replacing the SCU0. We are also working on a helical SCU for the APS. The status of these projects will be presented.« less

Feasibility of Reducing the Fiber Content in Ultra-High-Performance Fiber-Reinforced Concrete under Flexure.

PubMed

Park, Jung-Jun; Yoo, Doo-Yeol; Park, Gi-Joon; Kim, Sung-Wook

2017-01-28

In this study, the flexural behavior of ultra-high-performance fiber-reinforced concrete (UHPFRC) is examined as a function of fiber length and volume fraction. Straight steel fiber with three different lengths ( l f ) of 13, 19.5, and 30 mm and four different volume fractions ( v f ) of 0.5%, 1.0%, 1.5%, and 2.0% are considered. Test results show that post-cracking flexural properties of UHPFRC, such as flexural strength, deflection capacity, toughness, and cracking behavior, improve with increasing fiber length and volume fraction, while first-cracking properties are not significantly influenced by fiber length and volume fraction. A 0.5 vol % reduction of steel fiber content relative to commercial UHPFRC can be achieved without deterioration of flexural performance by replacing short fibers ( l f of 13 mm) with longer fibers ( l f of 19.5 mm and 30 mm).

Feasibility of Reducing the Fiber Content in Ultra-High-Performance Fiber-Reinforced Concrete under Flexure

PubMed Central

Park, Jung-Jun; Yoo, Doo-Yeol; Park, Gi-Joon; Kim, Sung-Wook

2017-01-01

In this study, the flexural behavior of ultra-high-performance fiber-reinforced concrete (UHPFRC) is examined as a function of fiber length and volume fraction. Straight steel fiber with three different lengths (lf) of 13, 19.5, and 30 mm and four different volume fractions (vf) of 0.5%, 1.0%, 1.5%, and 2.0% are considered. Test results show that post-cracking flexural properties of UHPFRC, such as flexural strength, deflection capacity, toughness, and cracking behavior, improve with increasing fiber length and volume fraction, while first-cracking properties are not significantly influenced by fiber length and volume fraction. A 0.5 vol % reduction of steel fiber content relative to commercial UHPFRC can be achieved without deterioration of flexural performance by replacing short fibers (lf of 13 mm) with longer fibers (lf of 19.5 mm and 30 mm). PMID:28772477

Demonstration of a real-time interferometer as a bunch-lenght monitor in a high-current electron beam accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thangaraj, J.; Thurman-Keup, R.; Ruan, J.

2012-03-01

A real-time interferometer (RTI) has been developed to monitor the bunch length of an electron beam in an accelerator. The RTI employs spatial autocorrelation, reflective optics, and a fast response pyro-detector array to obtain a real-time autocorrelation trace of the coherent radiation from an electron beam thus providing the possibility of online bunch-length diagnostics. A complete RTI system has been commissioned at the A0 photoinjector facility to measure sub-mm bunches at 13 MeV. Bunch length variation (FWHM) between 0.8 ps (-0.24 mm) and 1.5 ps (-0.45 mm) has been measured and compared with a Martin-Puplett interferometer and a streak camera.more » The comparisons show that RTI is a viable, complementary bunch length diagnostic for sub-mm electron bunches.« less

Analysis of the Factors Affecting Surgical Success of Implants Placed in Iranian Warfare Victims

PubMed Central

Jafarian, Mohammad; Bayat, Mohammad; Pakravan, Amir-Hossein; Emadi, Naghmeh

2016-01-01

Objective The aim was to evaluate the survival time and success rates of dental implants in warfare victims and factors that affect implant success. Subjects and Methods This retrospective study involved 250 Iranian warfare victims who received dental implants from 2003 to 2013. Patients' demographic characteristics, as well as the brand, diameter, length, location and failure rate of the implants were retrieved from patients' dental records and radiographs. The associations between these data and the survival rate were analyzed. Statistical analysis was carried out with χ2 and log-rank tests. Results Overall, out of the 1,533 dental implants, 61 (4s%) failed. The maxillary canine area had the highest failure rate [9 of 132 implants (6.8s%)], while the mandibular incisor region had the least number of failures [3 of 147 implants (2.0s%)] and the longest survival time (approximately 3,182 days). Maxillary canine areas had the shortest survival (about 2,996 days). The longest survival time was observed in implants with 11 mm length (3,179.72 ± 30.139 days) and 3.75-4 mm diameter (3,131.161 ± 35.96 days), and the shortest survival was found in implants with 11.5 mm length (2,317.79 ± 18.71 days) and 6.5 mm diameter (2,241.45 ± 182.21 days). Moreover, implants with 10 mm length (10.7s%) and 5.5-6 mm diameter (22.2s%) had the highest failure rate; however, the least failure rate occurred when the implants were 11.5 mm in length (1.9s%) and 3-3.5 mm in diameter (3.1s%). Conclusions The brand, length and diameter of implants affected the survival time, failure rate and time to failure. The location of the implant was not statistically significant regarding the mentioned factors, although it has clinical significance. PMID:27322534

Genome features of moderately halophilic polyhydroxyalkanoate-producing Yangia sp. CCB-MM3.

PubMed

Lau, Nyok-Sean; Sam, Ka-Kei; Amirul, Abdullah Al-Ashraf

2017-01-01

Yangia sp. CCB-MM3 was one of several halophilic bacteria isolated from soil sediment in the estuarine Matang Mangrove, Malaysia. So far, no member from the genus Yangia , a member of the Rhodobacteraceae family, has been reported sequenced. In the current study, we present the first complete genome sequence of Yangia sp. strain CCB-MM3. The genome includes two chromosomes and five plasmids with a total length of 5,522,061 bp and an average GC content of 65%. Since a different strain of Yangia sp. (ND199) was reported to produce a polyhydroxyalkanoate copolymer, the ability for this production was tested in vitro and confirmed for strain CCB-MM3. Analysis of its genome sequence confirmed presence of a pathway for production of propionyl-CoA and gene cluster for PHA production in the sequenced strain. The genome sequence described will be a useful resource for understanding the physiology and metabolic potential of Yangia as well as for comparative genomic analysis with other Rhodobacteraceae .

SUB 1-Millimeter Size Fresnel Micro Spectrometer

NASA Technical Reports Server (NTRS)

Park, Yeonjoon; Koch, Laura; Song, Kyo D.; Park, Sangloon; King, Glen; Choi, Sang

2010-01-01

An ultra-small micro spectrometer with less than 1mm diameter was constructed using Fresnel diffraction. The fabricated spectrometer has a diameter of 750 nmicrometers and a focal length of 2.4 mm at 533nm wavelength. The micro spectrometer was built with a simple negative zone plate that has an opaque center with an ecliptic shadow to remove the zero-order direct beam to the aperture slit. Unlike conventional approaches, the detailed optical calculation indicates that the ideal spectral resolution and resolving power do not depend on the miniaturized size but only on the total number of rings. We calculated 2D and 3D photon distribution around the aperture slit and confirmed that improved micro-spectrometers below 1mm size can be built with Fresnel diffraction. The comparison between mathematical simulation and measured data demonstrates the theoretical resolution, measured performance, misalignment effect, and improvement for the sub-1mm Fresnel micro-spectrometer. We suggest the utilization of an array of micro spectrometers for tunable multi-spectral imaging in the ultra violet range.

LAPAROSCOPIC OVARIECTOMY IN THE ASIATIC BLACK BEAR (URSUS THIBETANUS) WITH THE USE OF THE SONICISION™ DEVICE.

PubMed

Lee, Seung Y; Jeong, Dong H; Seok, Seong H; Yang, Jeong J; Kong, Ju Y; Park, Se J; Jin, So Y; Kim, Min H; Lee, Bae K; Lee, Hee C; Yeon, Seong C

2017-03-01

Laparoscopic ovariectomy was performed in two Asiatic black bears ( Ursus thibetanus ). Bears were placed in a 20° Trendelenburg position on a surgical table. A three-portal technique was used. A camera port was established 10 cm caudal to the umbilicus with a 5-mm cannula. Two instrument ports were made 1 cm caudal to the umbilicus with a 5-mm cannula and 8 cm caudal to the camera port with a 12-mm cannula, respectively. The suspensory ligament, ovarian vasculature, and uterine horn tip were progressively dissected following coagulation with the Sonicision™ cordless ultrasonic dissection device. The resected ovary was exteriorized through the 12-mm instrument portal site but enlarged to a 2-cm incision length. The abdominal musculature, subcutaneous tissue, and skin of the portal sites were closed separately. Total surgical time was 113 min (Bear A) and 49 min (Bear B), and no postoperative complications were encountered. This is the first report of laparoscopic ovariectomy in the Asiatic black bear.

Reproductive biology of the southern thorny skate Amblyraja doellojuradoi (Chondrichthyes, Rajidae).

PubMed

Delpiani, G

2016-04-01

The total lengths (L(T)) of 193 males (209-556 mm) and 130 females (275-515 mm) of Amblyraja doellojuradoi, a commercial by-catch species on the Argentinean continental shelf, which are increasingly retained, were analysed. No sexual dimorphism was observed in the L(T) at which 50% of individuals were sexually mature; males matured at 448 mm and females at 411 mm, c. 80 and 82% of maximum L(T). The hepato-somatic index was similar among sexes, but significantly different between maturity stages, being lower in mature than immature specimens. Males had no seasonal difference in the hepato-somatic index and females had the lowest index in autumn. The gonado-somatic index was lower in males than in females and significantly higher in mature than immature specimens of both sexes. Males had the highest index in autumn and females had no seasonal difference. Collectively, these results would indicate that A. doellojuradoi breeds in autumn. © 2016 The Fisheries Society of the British Isles.

Design of a panoramic long-wave infrared athermal system

NASA Astrophysics Data System (ADS)

Yao, Yuan; Geng, Anbing; Bai, Jian; Wang, Haitao; Guo, Jie; Xiong, Tao; Luo, Yujie; Huang, Zhi; Hou, Xiyun

2016-12-01

A panoramic long-wave infrared athermal system is introduced in this paper. The proposed system includes a panoramic annular lens (PAL) block providing a stereo field of view of (30 deg - 100 deg) × 360 deg without the need to move its components. Moreover, to ensure the imaging quality at different temperatures, a refractive/diffractive hybrid lens is introduced to achieve optical passive athermalization. The system operates in a spectral band between 8 and 12 μm, with a total length of 175 mm and a focal length of 3.4 mm. To get a bright and clear image, the aperture of the system was set to f/1.15. The introduction of aspherical surface and even-order diffractive surface not only eliminates the differential thermal but also makes the structure simple and lightweight and improves the image quality. The results show that the modulation transfer function below 20 lp/mm of the system is above 0.2 at each temperature ranging from -20°C to +60°C, which is close to the diffraction limit. The system is suitable to be applied in an uncooled infrared focal plane array detector and will serve as a static alert system. It has a number of pixels of 640×480, and the pixel size is 25 μm.

Resonator design and performance estimation for a space-based laser transmitter

NASA Astrophysics Data System (ADS)

Agrawal, Lalita; Bhardwaj, Atul; Pal, Suranjan; Kamalakar, J. A.

2006-12-01

Development of a laser transmitter for space applications is a highly challenging task. The laser must be rugged, reliable, lightweight, compact and energy efficient. Most of these features are inherently achieved by diode pumping of solid state lasers. Overall system reliability can further be improved by appropriate optical design of the laser resonator besides selection of suitable electro-optical and opto-mechanical components. This paper presents the design details and the theoretically estimated performance of a crossed-porro prism based, folded Z-shaped laser resonator. A symmetrically pumped Nd: YAG laser rod of 3 mm diameter and 60 mm length is placed in the gain arm with total input peak power of 1800 W from laser diode arrays. Electro-optical Q-switching is achieved through a combination of a polarizer, a fractional waveplate and LiNbO 3 Q-switch crystal (9 x 9 x 25 mm) placed in the feedback arm. Polarization coupled output is obtained by optimizing azimuth angle of quarter wave plate placed in the gain arm. Theoretical estimation of laser output energy and pulse width has been carried out by varying input power levels and resonator length to analyse the performance tolerances. The designed system is capable of meeting the objective of generating laser pulses of 10 ns duration and 30 mJ energy @ 10 Hz.

Supine Length, Weight and Head Circumference at Birth in Central Iran

ERIC Educational Resources Information Center

Ayatollahi, S. M. T.; Rafiei, Mohammad

2007-01-01

Supine length, weight and head circumferences of 10,241 neonates (5241 boys, 5000 girls, sex ratio 105) born in Arak (central Iran) in 2004 are reported. The mean plus or minus standard deviation of boys' and girls' (p value for sex difference) supine length (mm), weight (g) and head circumference (mm) were estimated as 501 plus or minus 30 and…

A novel approach to bar adsorptive microextraction: Cork as extractor phase for determination of benzophenone, triclocarban and parabens in aqueous samples.

PubMed

Dias, Adriana Neves; da Silva, Ana Cristine; Simão, Vanessa; Merib, Josias; Carasek, Eduardo

2015-08-12

This study describes the use of cork as a new coating for bar adsorptive microextraction (BAμE) and its application in determining benzophenone, triclocarban and parabens in aqueous samples by HPLC-DAD. In this study bars with 7.5 and 15 mm of length were used. The extraction and liquid desorption steps for BAμE were optimized employing multivariate and univariate procedures. The desorption time and solvent used for liquid desorption were optimized by univariate and multivariate studies, respectively. For the extraction step the sample pH was optimized by univariate experiments while the parameters extraction time and ionic strength were evaluated using the Doehlert design. The optimum extraction conditions were sample pH 5.5, NaCl concentration 25% and extraction time 90 min. Liquid desorption was carried out for 30 min with 250 μL (bar length of 15 mm) or 100 μL (bar length of 7.5 mm) of ACN:MeOH (50:50, v/v). The quantification limits varied between 1.6 and 20 μg L(-1) (bar length of 15 mm) and 0.64 and 8 μg L(-1) (bar length of 7.5 mm). The linear correlation coefficients were higher than 0.98 for both bars. The method with 7.5 mm bar length showed recovery values between 65 and 123%. The bar-to-bar reproducibility and the repeatability were lower than 13% (n = 2) and 14% (n = 3), respectively. Copyright © 2015 Elsevier B.V. All rights reserved.

Morphometric analysis of torso arterial anatomy with implications for resuscitative aortic occlusion.

PubMed

Stannard, Adam; Morrison, Jonathan J; Sharon, Danny J; Eliason, Jonathan L; Rasmussen, Todd E

2013-08-01

Hemorrhage is a leading cause of death in military and civilian trauma. Despite the importance of the aorta as a site of hemorrhage control and resuscitative occlusion, detailed knowledge of its morphometry is lacking. The objective of this study was to characterize aortic morphometry in a trauma population, including quantification of distances as well as and diameters and definition of relevant aortic zones. Center line measures were made (Volume Viewer) from contrast computed tomography (CT) scans of male trauma patients (18-45 years). Aortic zones were defined based on branch arteries. Zone I includes left subclavian to celiac; Zone II includes celiac to caudal renal; Zone III includes caudal renal to aortic bifurcation. Zone lengths were calculated and correlated to a novel external measure of torso extent (symphysis pubis to sternal notch). Eighty-eight males (mean [SD], 28 [4] years) had CT scans for the study. The median (interquartile range) lengths (mm) of Zones I, II, and III were 210 mm (202-223 mm), 33 mm (28-38 mm), and 97 mm (91-103 mm), respectively. Median aortic diameters at the left subclavian, celiac, and lowest renal arteries were 21 mm (20-23 mm), 18 mm (16-19 mm), and 15 mm (14-16 mm), respectively, and the terminal aortic diameter was 14 mm (13-15 mm). The correlation of determination for descending aortic length (all zones) against torso extend was r = 0.454. This study provides a morphometric analysis of the aorta in a male population, demonstrating consistency of length and diameter while defining distinct axial zones. Findings suggest that center line aortic distances correlate with a simple, external measure of torso extent. Morphometric study of the aorta using CT data may facilitate the development and implementation of occlusion techniques to manage noncompressible torso, pelvic, and junctional femoral hemorrhage.

Experimental Study on the Strength Characteristics and Water Permeability of Hybrid Steel Fibre Reinforced Concrete

PubMed Central

Singh, M. P.; Singh, S. P.; Singh, A. P.

2014-01-01

Results of an investigation conducted to study the effect of fibre hybridization on the strength characteristics such as compressive strength, split tensile strength, and water permeability of steel fibre reinforced concrete (SFRC) are presented. Steel fibres of different lengths, that is, 12.5 mm, 25 mm, and 50 mm, having constant diameter of 0.6 mm, were systematically combined in different mix proportions to obtain mono, binary, and ternary combinations at each of 0.5%, 1.0%, and 1.5% fibre volume fraction. A concrete mix containing no fibres was also cast for reference purpose. A total number of 1440 cube specimens of size 100∗100∗100 mm were tested, 480 each for compressive strength, split tensile strength, and water permeability at 7, 28, 90, and 120 days of curing. It has been observed from the results of this investigation that a fibre combination of 33% 12.5 mm + 33% 25 mm + 33% 50 mm long fibres can be adjudged as the most appropriate combination to be employed in hybrid steel fibre reinforced concrete (HySFRC) for optimum performance in terms of compressive strength, split tensile strength and water permeability requirements taken together. PMID:27379298

Lamb Wave Propagation in a Restricted Geometry Composite PI-Joint Specimen (Preprint)

DTIC Science & Technology

2011-11-01

adhesive, and were located along the length and height of the specimen as depicted in Figure 3. The sensors were 6.35 mm round disks of PZT , with a...in both cases for R1, R2, and R3. 3D Finite Element Model Geometry 200mm length 50mm width 140mm height x z y PZT Actuation Sensor...health monitoring using scanning laser vibrometry: III. Lamb waves for fatigue crack detection”, Smart Mater. Struct., Vol. 14, No. 6, 2005. 16

Detection of foreign bodies in foods using continuous wave terahertz imaging.

PubMed

Lee, Young-Ki; Choi, Sung-Wook; Han, Seong-Tae; Woo, Deog Hyun; Chun, Hyang Sook

2012-01-01

Foreign bodies (FBs) in food are health hazards and quality issues for many food manufacturers and enforcement authorities. In this study, continuous wave (CW) terahertz (THz) imaging at 0.2 THz with an output power of 10 mW was compared with X-ray imaging as techniques for inspection of food for FBs. High-density FBs, i.e., aluminum and granite pieces of various sizes, were embedded in a powdered instant noodle product and detected using THz and X-ray imaging. All aluminum and granite pieces (regular hexahedrons with an edge length of 1 to 5 mm) were visualized by both CW THz and X-ray imaging. THz imaging also detected maggots (length = 8 to 22 mm) and crickets (length = 35 and 50 mm), which were embedded in samples as low density FBs. However, not all sizes of maggot pieces embedded in powdered instant noodle were detected with X-ray imaging, although larger crickets (length = 50 mm and thickness = 10 mm) were detected. These results suggest that CW THz imaging has potential for detecting both high-density and low-density FBs embedded in food.

Goldeye, Hiodon alosoides, in Lake Oahe: abundance, age, growth, maturity, food, and the fishery, 1963-69

USGS Publications Warehouse

Miller, Grant L.; Nelson, William R.

1974-01-01

Reproductive success was relatively consistent, and adequate to maintain species abundance at a nearly constant level, during 1963-69. Both abundance and growth in length increased from the lower to the upper portion of the reservoir. In most characteristics -- growth in length, length-weight relation, age at maturity, and food -- goldeye in Lake Oahe were similar to those from other Missouri River impoundments. Experimental gill nets samples all lengths (range 80-460 mm; median, 320 mm) of goldeye, bottom trawls sampled mostly small fish, (median, 215 mm) and trap nets large ones (median, 345 mm). Commercial gill nets were highly size selective (median, 375 mm); fish of ages IV-VII made up 90% of the catch. Survival rates were 57 to 52% for ages II-X. Estimated survival rates for ages V-IX declined from 44 to 35% after the inception of the commercial fishery in 1966. The peak commercial catch was 151,432 kg (1.2 kg/hectare) in 1969. Unless recruitment declines, the population can support a fishery of that magnitude.

First Report of the Resolute Onyx 2.0-mm Zotarolimus-Eluting Stent for the Treatment of Coronary Lesions With Very Small Reference Vessel Diameter.

PubMed

Price, Matthew J; Saito, Shigeru; Shlofmitz, Richard A; Spriggs, Douglas J; Attubato, Michael; McLaurin, Brent; Popma Almonacid, Alexandra; Brar, Sandeep; Liu, Minglei; Moe, Elizabeth; Mehran, Roxana

2017-07-24

The aim of this study was to explore the safety and efficacy of a dedicated drug-eluting stent for the treatment of coronary lesions with very small reference vessel diameter (RVD). Smaller RVD is associated with increased risk for restenosis and target lesion failure (TLF) after stent implantation. This was a prospective, single-arm, multicenter trial of the Resolute Onyx 2.0-mm zotarolimus-eluting stent. The primary endpoint was 12-month TLF, which was compared with a pre-specified performance goal. Subjects with stable or unstable angina or ischemia, target lesions ≤27 mm in length, and RVD ≥2.0 and <2.25 mm were eligible for enrollment. A subset of subjects underwent follow-up angiography at 13 months post-procedure. A total of 101 subjects with 104 lesions were enrolled. The mean age was 67.3 ± 9.6 years, 47% of subjects had diabetes, the mean lesion length was 12.6 ± 6.3 mm, and the mean RVD was 1.91 ± 0.26 mm. The rate of TLF at 12 months was 5.0%, fulfilling the pre-specified performance goal of 19% (p < 0.001). The rates of target lesion revascularization and target vessel myocardial infarction were 2.0% and 3.0%, respectively. There were no episodes of stent thrombosis. In-stent late lumen loss was 0.26 ± 0.48 mm, and the rate of binary restenosis was 12.0%. In this first report of a drug-eluting stent with a dedicated size to treat lesions with RVD <2.25 mm, the Resolute Onyx 2.0-mm zotarolimus-eluting stent was associated with a low rate of TLF and late lumen loss, without a signal for stent thrombosis. This novel-sized drug-eluting stent appears to be a feasible option for the treatment of coronary lesions in extremely small vessels. (Medtronic Resolute Onyx 2.0 mm Clinical Study; NCT02412501). Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Design and numerical characterization of a crossover EBIS

NASA Astrophysics Data System (ADS)

Geyer, Sabrina; Langbein, A.; Meusel, Oliver; Kester, Oliver

2015-01-01

For the investigation of highly charged ions, a crossover EBIS (XEBIS) was developed at the University of Frankfurt. In contrast to conventional EBIS/T devices the compression of the electron beam is achieved by electrostatic focusing to a crossover point in the interaction region. This concept allows a compact and simple design. Simulations performed with EGUN show a perveance of 2.1×10-7 A/V3/2 for the realized gun system. In the interaction region the electron beam has a density of around 10 A/cm2 and a minimum radius of 0.15 mm. The XEBIS has a total length of 112 mm with a trap length of 26 mm. It is designed for electron beam energies of up to 6 keV/q. The storage capacity of the trap region is in the order of 1×108 charges. Charge state breeding studies with CBSIM indicate for the noble gases as maximal achievable charge state Ar16+, Kr30+ and Xe35+. Thus ion beam currents of around 2.04 nA assuming 50 Hz repetition rate can be expected. The emittance of the extracted beam is approximated to 8 mm mrad. After completion of the construction phase, the XEBIS will be installed for first performance investigations at a dedicated test bench, equipped with a fast Faraday Cup (FC), a retarding field spectrometer, a luminescence screen and optical diagnostics. Subsequently the XEBIS will serve as source for highly charged ions at different experimental setups.

SEM study of the oral cavity of members of the Kyphosidae and Girellidae (Pisces, Teleostei), with remarks on Crenidens (Sparidae), focusing on teeth and taste bud numbers and distribution.

PubMed

Fishelson, Lev; Golani, Daniel; Diamant, Ariel

2014-04-01

The present study compares dental morphology and taste bud distribution in the oral cavity of four species of the teleost family Kyphosidae, five species of Girellidae and one species of Sparidae. Some of these species are predominantly herbivorous, while others are omnivorous with a high portion of invertebrates in their diets. All the kyphosids feature one row of frontal cusped teeth on their jaws and areas of miniature teeth on the tongue and palate; the girellid species feature 2-5 rows of denticulate teeth, and no teeth inside the oral cavity. The total number of taste buds in the oral cavity is higher in Girella spp. than in the kyphosids, and their number is species-specific, not correlated with fish size. For example, Kyphosus bigibbus of 500mm standard length bears 1780 taste buds, while the kyphosid Neoscorpis lithophilus of 80mm bears 3460. The maximum number of taste buds, 7900, is found in Girella punctata of 60mm standard length, and the minimum number, 1320, in Kyphosus vaigiensis of 175mm. The higher number of taste buds appears to characterize species that possess a more diversified diet. The present study contributes to our understanding of the differences between the two families Kyphosidae and Girellidae. In particular, it relates the eco-morphological adaptations to the type of diet consumed by the various species. Copyright © 2014. Published by Elsevier GmbH.

Factors affecting the achievement of Japanese-style deep knee flexion after total knee arthroplasty using posterior-stabilized prosthesis with high-flex knee design.

PubMed

Niki, Yasuo; Takeda, Yuki; Harato, Kengo; Suda, Yasunori

2015-11-01

Achievement of very deep knee flexion after total knee arthroplasty (TKA) can play a critical role in the satisfaction of patients who demand a floor-sitting lifestyle and engage in high-flexion daily activities (e.g., seiza-sitting). Seiza-sitting is characterized by the knees flexed >145º and feet turned sole upwards underneath the buttocks with the tibia internally rotated. The present study investigated factors affecting the achievement of seiza-sitting after TKA using posterior-stabilized total knee prosthesis with high-flex knee design. Subjects comprised 32 patients who underwent TKA with high-flex knee prosthesis and achieved seiza-sitting (knee flexion >145º) postoperatively. Another 32 patients served as controls who were capable of knee flexion >145º preoperatively, but failed to achieve seiza-sitting postoperatively. Accuracy of femoral and tibial component positions was assessed in terms of deviation from the ideal position using a two-dimensional to three-dimensional matching technique. Accuracies of the component position, posterior condylar offset ratio and intraoperative gap length were compared between the two groups. The proportion of patients with >3º internally rotated tibial component was significantly higher in patients who failed at seiza-sitting (41 %) than among patients who achieved it (13 %, p = 0.021). Comparison of intraoperative gap length between patient groups revealed that gap length at 135º flexion was significantly larger in patients who achieved seiza-sitting (4.2 ± 0.4 mm) than in patients who failed at it (2.7 ± 0.4 mm, p = 0.007). Conversely, no significant differences in gap inclination were seen between the groups. From the perspective of surgical factors, accurate implant positioning, particularly rotational alignment of the tibial component, and maintenance of a sufficient joint gap at 135º flexion appear to represent critical factors for achieving >145º of deep knee flexion after TKA.

Low pH affects survival, growth, size distribution, and carapace quality of the postlarvae and early juveniles of the freshwater prawn Macrobrachium rosenbergii de Man

NASA Astrophysics Data System (ADS)

Kawamura, Gunzo; Bagarinao, Teodora; Yong, Annita Seok Kian; Chen, Chiau Yu; Noor, Siti Norasidah Mat; Lim, Leong Seng

2015-06-01

Acidification of rain water caused by air pollutants is now recognized as a serious threat to aquatic ecosystems. We examined the effects of low pH (control pH 7.5, pH 6, pH 5, pH 4) on the survival, growth, and shell quality of Macrobrachium rosenbergii postlarvae and early juveniles in the laboratory. Hatcheryproduced postlarvae (PL 5) were stocked at 250 PL per aquarium, acclimated over 7 d to experimental pH adjusted with hydrochloric acid, and reared for 30 d. Dead specimens were removed and counted twice a day. After 27 d rearing, all specimens were measured for total length and body weight. Carapace quality was assessed by spectrophotometry. Survival of juveniles was highest at pH 6 (binomial 95% confidence interval 79 - 89%) followed by control pH 7.5 (56 - 68%) and pH 5 (50 - 60%) and was lowest for unmetamorphosed postlarvae and juveniles at pH 4 (43 - 49%). The final median total length and body weight of juveniles were similar at control pH 7.5 (18.2 TL, 50.2 mg BW) and pH 6 (17.7 mm TL, 45.0 mg BW) but significantly less at pH 5 (16.7 mm TL, 38.2 mg BW); at pH 4, the postlarvae did not metamorphose and measured only 9.8 mm TL, 29.3 mg BW. Length frequency distribution showed homogeneous growth at pH 6, positive skew at control pH 7.5 and pH 5, and extreme heterogeneity at pH 4. The carapace showed different transmittance spectra and lower total transmittance (i.e. thicker carapace) in juveniles at pH 7.5, pH 6, and pH 5 than in unmetamorphosed postlarvae and juveniles with thinner carapace at pH 4. Thus, survival, growth, size distribution, and carapace quality of M. rosenbergii postlarvae and early juveniles were negatively affected by pH 5 and especially pH 4. The thinner carapace of the survivors at pH 4 was mostly due to their small size and failure to metamorphose. Natural waters affected by acid rain could decimate M. rosenbergii populations in the wild.

Qualification of a Quantitative Laryngeal Imaging System Using Videostroboscopy and Videokymography

PubMed Central

Popolo, Peter S.; Titze, Ingo R.

2008-01-01

Objectives: We sought to determine whether full-cycle glottal width measurements could be obtained with a quantitative laryngeal imaging system using videostroboscopy, and whether glottal width and vocal fold length measurements were repeatable and reliable. Methods: Synthetic vocal folds were phonated on a laboratory bench, and dynamic images were obtained in repeated trials by use of videostroboscopy and videokymography (VKG) with an imaging system equipped with a 2-point laser projection device for measuring absolute dimensions. Video images were also obtained with an industrial videoscope system with a built-in laser measurement capability. Maximum glottal width and vocal fold length were compared among these 3 methods. Results: The average variation in maximum glottal width measurements between stroboscopic data and VKG data was 3.10%. The average variations in width measurements between the clinical system and the industrial system were 1.93% (stroboscopy) and 3.49% (VKG). The variations in vocal fold length were similarly small. The standard deviations across trials were 0.29 mm for width and 0.48 mm for length (stroboscopy), 0.18 mm for width (VKG), and 0.25 mm for width and 0.84 mm for length (industrial). Conclusions: For stable, periodic vibration, the full extent of the glottal width can be reliably measured with the quantitative videostroboscopy system. PMID:18646436

Accurate real-time sensing tip for aqueous NO with optical fibers embedded in active hydrogel waveguide

NASA Astrophysics Data System (ADS)

Chung, Chieh-Wen; Tsai, May-Jywan; Lin, Peng-Wei; Huang, Ding-Wen; Wang, Kuan-Hsun; Chen, Yu-An; Meng, Hsin-Fei; Zan, Hsiao-Wen; Cheng, Henrich; Tong, Limin; Zhang, Lei; Horng, Sheng-Fu; Hung, Cheng-Hsiung

2018-02-01

A NO sensing tip is made by inserting two parallel optical fibers inside a poly 2-hydroxyethyl methacrylate (PolyHEMA) hydrogel waveguide mixed with the probe molecule 1, 2-Diaminoanthraquinone (DAQ). There is a length difference of 1 mm between the two fibers, and the light has to propagate through the difference from the short fiber to the long fiber. The total cross section area of the active hydrogel waveguide embedded with the fibers is only 3mm x 1.2 mm. For practical use the tip is housed in a needle for mechanical protection and the sensing tip is able to detect aqueous NO concentration around 1 μM with time resolution about 5 minutes. Such a sensing tip can be used to monitor the medical conditions inside the brain after a stroke or a brain injury.

Optical Design with Narrow-Band Imaging for a Capsule Endoscope.

PubMed

Yen, Chih-Ta; Lai, Zong-Wei; Lin, Yu-Ting; Cheng, Hsu-Chih

2018-01-01

The study proposes narrow-band imaging (NBI) lens design of 415 nm and 540 nm of a capsule endoscope (CE). The researches show that in terms of the rate of accuracy in detecting and screening neoplastic and nonneoplastic intestinal lesions, the NBI system outperformed that of traditional endoscopes and rivaled that of chromoendoscopes. In the proposed NBI CE optical system, the simulation result shows the field of view (FOV) was 109.8°; the modulation transfer function (MTF) could achieve 12.5% at 285 lp/mm and 34.1% at 144 lp/mm. The relative illumination reaches more than 60%, and the system total length was less than 4 mm. Finally, this design provides high-quality images for a 300-megapixel 1/4 ″ CMOS image sensor with a pixel size of 1.75  μ m.

Seat and seatbelt accommodation in fire apparatus: Anthropometric aspects

PubMed Central

Hsiao, Hongwei; Whitestone, Jennifer; Wilbur, Michael; Lackore, J. Roger; Routley, J. Gordon

2015-01-01

This study developed anthropometric information on U.S. firefighters to guide fire-apparatus seat and seatbelt designs and future standards development. A stratified sample of 863 male and 88 female firefighters across the U.S. participated in the study. The study results suggested 498 mm in width, 404 mm in depth, and 365–476 mm in height for seat pans; 429–522 mm in width and 542 mm in height for seat back; 871 mm in height for head support; a seat space of 733 mm at shoulder and 678 mm at hip; and a knee/leg clearance of 909 mm in fire truck cab. Also, 1520 mm of lap belt web effective length and 2828 mm of lap-and-shoulder belt web effective length were suggested. These data for firetruck seats and seatbelts provide a foundation for fire apparatus manufacturers and standards committees to improve firefighter seat designs and seatbelt usage compliance. PMID:26154212

Gnathostoma infection in Nakhon Nayok and Prachin Buri, Central Thailand.

PubMed

Rojekittikhun, Wichit; Chaiyasith, Tossapon; Nuamtanong, Supaporn; Pubampen, Somchit; Maipanich, Wanna; Tungtrongchitr, Rungsunn

2002-09-01

Gnathostoma infection in Nakhon Nayok and Prachin Buri Provinces, Central Thailand, was investigated. The prevalence and intensity of infection of swamp eels were determined; dog fecal samples and fresh-water copepods were examined for evidence of infection. The overall prevalence of eel infection was 38.1% (117/307) in Nakhon Nayok and 24.0% (74/308) in Prachin Buri--the former rate being significantly higher than the latter. Most of the positive Nalkhon Nayok eels (53.8%) harbored only 1-9 larvae; only one eel bore more than 50 larvae. In Prachin Buri, 67.6% of the positive eels harbored 1-9 larvae; again, only one eel bore more than 50 larvae. The mean number of 11.0 +/- 10.4 larvae/eel in Nakhon Nayok was not significantly different from that of Prachin Buri (9.3 +/- 11.4). A total of 1,292 gnathostome larvae were recovered from 307 eels in Nakhon Nayok. Of these, 52.3% had accumulated in the liver and 47.7% had spread throughout the muscles. In eels from Prachin Buri, 50.6% and 49.4% of the total of 688 larvae (from 308 eels) were found in the liver and muscles, respectively. The larvae preferred encysting in ventral of muscles rather than dorsal part; they preferred the middle portion to the anterior and posterior portions. The average length of gnathostome larvae recovered from Nakhon Nayok eels was 4.0 +/- 0.5 mm (range 2.5-5.1 mm) and the average body width was 0.40 +/- 0.05 mm (range 0.29-0.51 mm). Those from eels in Prachin Buri were 3.9 +/- 0.5 mm (range 2.2-5.1 mm) and 0.34 +/- 0.05 mm (range 0.20-0.48 mm), respectively. The mean body length and width of the larvae from eels in Nakhon Nayok were significantly greater than those of the larvae from eels in Prachin Buri. In Ban Phrao, Nakhon Nayok, none of the first 44 fecal specimens examined was positive. Of the second (68) and the third (70) specimens, one (1.5%) and two (2.9%) samples were positive. However, six months after the third fecal collection, no eggs were found. In Tha Ngam, Prachin Buri, no eggs were found in all three batches (109, 115, and 100 fecal samples). A cyclops survey of 4,000-5,000 crustacea from each of two areas (Ban Phrao and Tha Ngam) found no evidence of natural cyclops infection.

The effect of pulmonary hypertension on ovine tricuspid annular dynamics.

PubMed

Malinowski, Marcin; Wilton, Penny; Khaghani, Asghar; Langholz, David; Hooker, Victoria; Eberhart, Lenora; Hooker, Robert L; Timek, Tomasz A

2016-01-01

Pulmonary hypertension (PHT) is associated with tricuspid annular dilatation, but the effect of acute increase of pulmonary pressure on three-dimensional (3D) tricuspid annular dynamics and shape is unknown. Better understanding of tricuspid annular dynamics may lead to improved and more durable surgical reparative techniques. In nine open-chest anaesthetized sheep nine sonomicrometry crystals were implanted on the right ventricle while on cardiopulmonary bypass. Additional nine crystals were implanted around the tricuspid annulus (TA) with one crystal at each commissure defining three separate annular regions: anterior, posterior and septal. Two additional equidistant crystals were implanted between each commissure, creating three segments for every region. Pressure transducers were placed in the left ventricular (LV), right ventricular (RV) and right atrium. PHT was induced by acute pulmonary artery constriction with a pneumatic occluder. Sonomicrometry and echocardiographic data were collected before and after induction of PHT. TA area, regional and total perimeter, and 3D annular geometry were calculated from 3D crystal coordinates. Regional annular contraction was defined as the percentage difference between maximal and minimal region length during the cardiac cycle. PHT increased RV pressure from 31 ± 9 mmHg to 46 ± 13 mmHg (P = 0.001) and decreased left ventricular (LV) pressure from 111 ± 24 mmHg to 78 ± 36 mmHg (P = 0.018). There was no significant tricuspid regurgitation observed with PHT. During PHT, the TA area increased by 12 ± 13% from 641 ± 139 mm(2) to 721 ± 177 mm(2) (P = 0.037). The total perimeter increased from 103 ± 11 mm to 109 ± 13 mm (P = 0.02). All annular regions dilated significantly with PHT with 8 ± 10, 5 ± 5 and 5 ± 5% increase in anterior, posterior and septal annular length, respectively (P < 0.05). PHT reduced regional annular contraction in the anterior region only (17 ± 7 vs 14 ± 8%; P = 0.02). The TA had a complex 3D saddle geometry and the shape of the annulus was altered during PHT only in the antero-posterior region. The changes in tricuspid annular conformation, contractility and its 3D geometry observed during acute ovine PHT may help in the design of new pathology-specific tricuspid annular rings. © The Author 2015. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Experimental investigation of a scaled-up passive micromixer with uneven interdigital inlet and teardrop obstruction elements

NASA Astrophysics Data System (ADS)

Cook, Kristina J.; Fan, YanFeng; Hassan, Ibrahim

2012-05-01

Micromixers are vital components in micro total analysis systems. It is desirable to develop micromixers which are capable of rapidly mixing two or more fluids in a small footprint area, while minimizing mechanical losses. A novel planar scaled-up passive micromixer is experimentally investigated in this study. The design incorporates a 7-substream uneven interdigital inlet which supplies two liquid species in a parallel arrangement and promotes diffusion along the side walls. Forty-eight staggered teardrop-shaped obstruction elements located along the channel length combined with 32 side walls protrusions increase the two-fluid interfacial area while converging the flow due to periodic reductions in cross-sectional area. The scaled-up micromixer has a mixing channel length of 110 mm with a mixing channel height and width of 2 and 5 mm, respectively. Experimental investigations are carried out at four locations along the channel length and at Reynolds numbers equal to 1, 5, 10, 25, 50, and 100, where the Reynolds number is calculated based on total two-fluid flow and the mixing channel hydraulic diameter. Flow visualization is employed to study flow patterns, while induced fluorescence (IF), using de-ionized water and low concentration Rhodamine 6G solutions, provides mixing efficiency data. Results show a change in dominant mixing mechanism from mass diffusion to mass advection, with a critical Reynolds number of 25. At high Reynolds numbers, the formation of additional lamellae is observed, as is the formation of Dean vortices in the vicinity of the teardrop obstructions. Of the tested cases, the highest outlet mixing efficiency, 68.5%, is achieved at a Reynolds number of 1, where mass diffusion dominates. At low Reynolds numbers, superior mixing efficiency is due primarily to the implementation of the uneven interdigital inlet. A comparable mixing length is proposed to allow for reasonable comparison with published studies.

Captive breeding of the barndoor skate (Dipturus laevis) at the Montreal Biodome, with comparison notes on two other captive-bred skate species.

PubMed

Parent, Serge; Pépin, Serge; Genet, Jean-Pierre; Misserey, Laurent; Rojas, Salvador

2008-03-01

In 1997, the Montreal Biodome obtained five barndoor skates (Dipturus laevis) from the waters off Boston, Massachusetts. Six years later, those specimens began reproducing, and the first egg case was collected in November 2003. Since then, 73 hatchlings have been born and raised. Egg cases were observed year round, and annual fecundity was measured for the first time: one female laid 69 eggs in 2005, 85 in 2006 and 115 in 2007. Egg incubation was longer than believed previously, ranging from 342 to 494 days. Hatching occurred throughout the year. Hatchlings averaged 193 mm total length and 128 mm disk width and weighed 32 g. They were fed krill and diced fish. All but one survived the first month. A photo identification system was useful in recognizing two groups of 10 specimens during their first year, and transponders could be inserted in the wing muscles of 1-year-old skates. Total lengths at birth and at age 2 were similar to the data reported from the wild, suggesting a similar growth pattern in captivity. The reproduction characteristics of the barndoor skate were compared with those of two other skate species currently bred at the Montreal Biodome, the winter skate (Leucoraja ocellata) and the thorny skate (Amblyraja radiata). Zoo Biol 27:145-153, 2008. (c) 2008 Wiley-Liss, Inc.

A comparison of two reciprocating instruments using bending stress and cyclic fatigue tests.

PubMed

Scelza, Pantaleo; Harry, Davidowicz; Silva, Licinio Esmeraldo da; Barbosa, Igor Bastos; Scelza, Miriam Zaccaro

2015-01-01

The aim of this study was to comparatively evaluate the bending resistance at 45º, the static and dynamic cyclic fatigue life, and the fracture type of the WaveOne (Dentsply Maillefer, Ballaigues, Switzerland) 25-08 and Reciproc (VDW, Munich, Germany) 25-08 instruments. A total of 60 nickel-titanium (NiTi) instruments (30 Reciproc and 30 WaveOne) from three different lots, each of which was 25 mm in length, were tested. The bending resistance was evaluated through the results of a cantilever-bending test conducted using a universal testing machine. Static and dynamic cyclic fatigue testing was conducted using a custom-made device. For the static and dynamic tests, a cast Ni-Cr-Mo-Ti alloy metal block with an artificial canal measuring 1.77 mm in diameter and 20.00 mm in total length was used. A scanning electron microscope was used to determine the type of fracture. Statistical analyses were performed on the results. The WaveOne instrument was less flexible than the Reciproc (p < 0.05). The Reciproc instrument showed better resistance in the static and dynamic cyclic fatigue tests (p < 0.05). The transverse cross-section and geometry of the instruments were important factors in their resistance to bending and cyclic fracture. Both of the instruments showed ductile-type fracture characteristics. It can be concluded that the Reciproc 25-08 instrument was more resistant to static and dynamic cyclic fatigue than the WaveOne 25-08 instrument, while the WaveOne 25-08 instrument was less flexible. Bending and resistance to cyclic fracture were influenced by the instruments' geometries and transverse cross-sections. Both of the instruments showed ductile-type fracture characteristics.

Emergent Sandbar Construction for Least Terns on the Missouri River: Effects on Forage Fishes in Shallow-Water Habitats

USGS Publications Warehouse

Stucker, J.H.; Buhl, D.A.; Sherfy, M.H.

2011-01-01

Emergent sandbars on the Missouri River are actively managed for two listed bird species, piping plovers and interior least terns. As a plunge-diving piscivore, endangered least terns rely on ready access to appropriately sized slender-bodied fish: <52mm total length for adults and <34mm total length for young chicks. As part of a multi-agency recovery programme, aimed at enhancing nesting habitat for plovers and terns, the U.S. Army Corps of Engineers mechanically created several emergent sandbars on the Missouri River. However, it was unknown whether sandbar construction is a benefit or a detriment to forage abundance for least terns. Therefore, we studied the shallowwater (<1.5 m) fish community near river and mechanically created emergent sandbars during three nesting seasons (2006-2008). We sampled every 2 weeks each year from late May to July within 15-16 areas to document the relative abundance, species richness and size classes of fish. Fish relative abundance was negatively related to depth. Catches were dominated by schooling species, including emerald shiner, sand shiner, spotfin shiner and bigmouth buffalo. Significant inter-annual differences in relative abundance were observed, with generally increasing trends in intra-seasonal relative abundance of shiners and the smallest size classes of fish (<34 mm). Significant differences in the fish communities between the sandbar types were not detected in this study. Results suggest that mechanical sandbar habitats host comparable fish communities at similar levels of relative abundance. Further analyses are required to evaluate if the levels of fish relative abundance are adequate to support least tern foraging and reproduction.

KI-67 heterogeneity in well differentiated gastro-entero-pancreatic neuroendocrine tumors: when is biopsy reliable for grade assessment?

PubMed

Grillo, Federica; Valle, Luca; Ferone, Diego; Albertelli, Manuela; Brisigotti, Maria Pia; Cittadini, Giuseppe; Vanoli, Alessandro; Fiocca, Roberto; Mastracci, Luca

2017-09-01

Ki-67 heterogeneity can impact on gastroenteropancreatic neuroendocrine tumor grade assignment, especially when tissue is scarce. This work is aimed at devising adequacy criteria for grade assessment in biopsy specimens. To analyze the impact of biopsy size on reliability, 360 virtual biopsies of different thickness and lengths were constructed. Furthermore, to estimate the mean amount of non-neoplastic tissue component present in biopsies, 28 real biopsies were collected, the non-neoplastic components (fibrosis and inflammation) quantified and the effective area of neoplastic tissue calculated for each biopsy. Heterogeneity of Ki-67 distribution, G2 tumors and biopsy size all play an important role in reducing the reliability of biopsy samples in Ki-67-based grade assignment. In particular in G2 cases, 59.9% of virtual biopsies downgraded the tumor and the smaller the biopsy, the more frequent downgrading occurs. In real biopsies the presence of non-neoplastic tissue reduced the available total area by a mean of 20%. By coupling the results from these two different approaches we show that both biopsy size and non-neoplastic component must be taken into account for biopsy adequacy. In particular, we can speculate that if the minimum biopsy area, necessary to confidently (80% concordance) grade gastro-entero-pancreatic neuroendocrine tumors on virtual biopsies ranges between 15 and 30 mm 2 , and if real biopsies are on average composed of only 80% of neoplastic tissue, then biopsies with a surface area not <12 mm 2 should be performed; using 18G needles, this corresponds to a minimum total length of 15 mm.

Finite Element Analysis of Bone Stress around Micro-Implants of Different Diameters and Lengths with Application of a Single or Composite Torque Force.

PubMed

Lu, Ying-juan; Chang, Shao-hai; Ye, Jian-tao; Ye, Yu-shan; Yu, Yan-song

2015-01-01

Stress on the bone surrounding dental micro-implants affects implant success. To compare the stress on the bone surrounding a micro-implant after application of a single force (SF) of 200 g or a composite force (CF) of 200 g and 6 N.mm torque. Finite element models were developed for micro-implant diameters of 1.2, 1.6, and 2.0 mm, and lengths of 6, 8, 10, and 12 mm and either a SF or CF was applied. The maximum equivalent stress (Max EQS) of the bone surrounding the micro-implant was determined, and the relationships among type of force, diameter, and length were evaluated. The Max EQS of the CF exceeded that of the SF (P< 0.05). The effect of force on stress was related to implant diameter, but not to implant length. The larger CF led to greater instability of the micro-implant and the effect was most pronounced at an implant diameter of 1.2 mm. The use of implant diameters of 1.6 mm and 2.0 mm produced no significant difference in implant stability when either a CF or SF was applied. When considering the use of an implant to perform three-dimensional control on the teeth, the implant diameter chosen should be > 1.2 mm.

Finite Element Analysis of Bone Stress around Micro-Implants of Different Diameters and Lengths with Application of a Single or Composite Torque Force

PubMed Central

Lu, Ying-juan; Chang, Shao-hai; Ye, Jian-tao; Ye, Yu-shan; Yu, Yan-song

2015-01-01

Background Stress on the bone surrounding dental micro-implants affects implant success. Purpose To compare the stress on the bone surrounding a micro-implant after application of a single force (SF) of 200 g or a composite force (CF) of 200 g and 6 N.mm torque. Materials and Methods Finite element models were developed for micro-implant diameters of 1.2, 1.6, and 2.0 mm, and lengths of 6, 8, 10, and 12 mm and either a SF or CF was applied. The maximum equivalent stress (Max EQS) of the bone surrounding the micro-implant was determined, and the relationships among type of force, diameter, and length were evaluated. Results The Max EQS of the CF exceeded that of the SF (P< 0.05). The effect of force on stress was related to implant diameter, but not to implant length. The larger CF led to greater instability of the micro-implant and the effect was most pronounced at an implant diameter of 1.2 mm. The use of implant diameters of 1.6 mm and 2.0 mm produced no significant difference in implant stability when either a CF or SF was applied. Conclusion When considering the use of an implant to perform three-dimensional control on the teeth, the implant diameter chosen should be > 1.2 mm. PMID:26659581

[Effects of population density and culture volume on the growth and reproduction of Moina irrasa].

PubMed

Chen, Li-Na; Li, Yu-Ying; Deng, Dao-Gui; Jin, Xian-Wen; Ge, Qian; Wang, Shao-Qin

2012-07-01

A laboratory experiment was conducted to study the effects of different population density (D1 : 100 ind x L(-1), D2 : 150 ind x L(-1), D3 : 300 ind x L(-1)) and culture volume (V1: 50 mL, V2 : 100 mL, V3 : 400 mL) on the growth and reproduction of Moina irrasa at 25 degrees C. At the same culture density, the body length of the M. irrasa females at their first pregnancy, the first brood, and the total offsprings per female decreased with the increase of culture volumes, while the sex ratio (male/female) of the offsprings was in adverse. At the same culture volumes, the total offsprings per female decreased with the increase of culture density. At D1 V1, the body length of the females at their first pregnancy (0.95 +/- 0.10 mm) and the total offsprings (171.3 +/- 19.8 ind) per female were the maximum. At D3V2, the sex ratio was the maximum (0.54 +/- 0.05). Culture density, culture volume, and their interactions significantly affected the total offsprings per female and the sex ratio (P < 0.001).

A laboratory evaluation of tagging-related mortality and tag loss in juvenile humpback chub

USGS Publications Warehouse

Ward, David L.; Persons, William R.; Young, Kirk; Stone, Dennis M.; Van Haverbeke, Randy; Knight, William R.

2015-01-01

We quantified tag retention, survival, and growth in juvenile, captive-reared Humpback Chub Gila cypha marked with three different tag types: (1) Biomark 12.5-mm, 134.2-kHz, full duplex PIT tags injected into the body cavity with a 12-gauge needle; (2) Biomark 8.4-mm, 134.2-kHz, full duplex PIT tags injected with a 16-gauge needle; and (3) Northwest Marine Technology visible implant elastomer (VIE) tags injected under the skin with a 29-gauge needle. Estimates of tag loss, tagging-induced mortality, and growth were evaluated for 60 d with each tag type for four different size-groups of fish: 40–49 mm, 50–59 mm, 60–69 mm, and 70–79 mm TL. Total length was a significant predictor of the probability of PIT tag retention and mortality for both 8-mm and 12-mm PIT tags, and the smallest fish had the highest rates of tag loss (12.5–30.0%) and mortality (7.5–20.0%). Humpback Chub of sizes 40–49 mm TL and tagged with VIE tags had no mortality but did have a 17.5% tag loss. Growth rates of all tagged fish were similar to controls. Our data indicate Humpback Chub can be effectively tagged using either 8-mm or 12-mm PIT tags with little tag loss or mortality at sizes as low as 65 mm TL.

Clinical experience in coronary stenting with the Vivant Z Stent.

PubMed

Chee, K H; Siaw, F S; Chan, C G; Chong, W P; Imran, Z A; Haizal, H K; Azman, W; Tan, K H

2005-06-01

This single centre study was designed to demonstrate feasibility, safety and efficacy of the Vivant Z stent (PFM AG, Cologne, Germany). Patients with de novo lesion were recruited. Coronary angioplasty was performed with either direct stenting or after balloon predilatation. Repeated angiogram was performed 6 months later or earlier if clinically indicated. Between January to June 2003, a total of 50 patients were recruited (mean age 55.8 +/- 9 years). A total of 52 lesions were stented successfully. Mean reference diameter was 2.77 mm (+/-0.59 SD, range 2.05-4.39 mm) with mean target lesion stenosis of 65.5% (+/-11.6 SD, range 50.1-93.3%). Forty-six lesions (88.5%) were American College of Cardiologist/American Heart Association class B/C types. Direct stenting was performed in 18 (34.6%) lesions. Mean stent diameter was 3.18 mm (+/-0.41 SD, range 2.5-4 mm), and mean stent length was 14.86 mm (+/-2.72 SD, range 9-18 mm). The procedure was complicated in only one case which involved the loss of side branch with no clinical sequelae. All treated lesions achieved Thrombolysis In Myocardial Infarction 3 flow. Mean residual diameter stenosis was 12.2% (+/-7.55 SD, range 0-22.6%) with acute gain of 1.72 mm (+/-0.50 SD, range 0.5-2.8). At 6 months, there was no major adverse cardiovascular event. Repeated angiography after 6 months showed a restenosis rate of 17% (defined as >50% diameter restenosis). Mean late loss was 0.96 mm (+/-0.48 SD) with loss index of 0.61 (+/-0.38 SD). The restenosis rate of those lesions less than 3.0 mm in diameter was 22.2% compared with 6.25% in those lesions more than 3.0 mm in diameter. The Vivant Z stent was shown to be safe and efficacious with low restenosis rate in de novo coronary artery lesion.

Aortic elongation in aortic aneurysm and dissection: the Tübingen Aortic Pathoanatomy (TAIPAN) project.

PubMed

Krüger, Tobias; Sandoval Boburg, Rodrigo; Lescan, Mario; Oikonomou, Alexandre; Schneider, Wilke; Vöhringer, Luise; Lausberg, Henning; Bamberg, Fabian; Blumenstock, Gunnar; Schlensak, Christian

2018-01-24

To study the lengths and diameters of aortic segments in healthy and diseased aortas and to assess the role of aortic elongation in Type A aortic dissection (TAD) prediction. Ectasia and aneurysm were defined by ascending aorta diameters of 45-54 mm and ≥55 mm, respectively. Computed tomography angiography studies of 256 healthy, 102 ectasia, 38 aneurysm, 17 pre-TAD and 166 TAD aortas were analysed using curved multiplanar reformats. The study groups were structurally equal. The diameter of the ascending aorta was 35 mm in the control group and was larger (P < 0.001) in the pre-TAD (43 mm) and TAD (56 mm) groups. The length of the ascending aorta from the aortic annulus to the brachiocephalic trunk was 92 mm in the control group, 113 mm in the ectasia group, 120 mm in the aneurysm group and 111 mm and 118 mm in the pre-TAD and TAD groups (all P < 0.001 compared with the control group). An ascending aorta length of 120 mm was exceeded in 2% of the control group, 31% of the ectasia group, 50% of the aneurysm group, 24% of the pre-TAD group and 48% of the TAD group. The correlation between the diameter and the length of the ascending aorta was r = 0.752; therefore, both parameters must be examined separately. A score considering both parameters identified 23.5% of pre-TAD patients, significantly more than the diameter alone, and 31.4% of ectasia aortas were elongated. Patients with ectatic (45-54 mm diameter) and elongated (≥120 mm) ascending aortas represent a high-risk subpopulation for TAD. © The Author(s) 2018. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Comparative range of orthodontic wires.

PubMed

Ingram, S B; Gipe, D P; Smith, R J

1986-10-01

ADA specification No. 32 for determining the range (elastic limit) of orthodontic wires uses the bending of a wire section treated as a cantilever beam. An alternative method for defining the range of orthodontic wires proposed by Waters (1981) is to wrap wire sections around mandrels of varying diameters and measure the deformation imparted after unwrapping. Four brass mandrels with a total of 46 test diameters ranging from 3.5 to 60.0 mm were used in this study. Wire sections 9 cm in length were rolled on the mandrel with a hand lathe. The mandrel cross section required to produce a predetermined amount of deformation (2 mm arc height for a 5 cm chord) was defined as the yield diameter for that particular wire. No individual wire was tested twice so as to avoid introduction of strain history. Test samples of 488 different orthodontic wires supplied by nine commercial distributors were evaluated (a total of 4,747 samples). Stainless steel wires of identical dimensions had a large variation in range, depending on the state of strain hardening and heat treatment. For example, 0.020 inch round wire had yield diameters ranging from 22.8 mm for Australian special plus orange (TP Laboratories) to 42.9 mm for Nubryte gold (G.A.C. International). Chromium cobalt wires had less range than stainless steel before heat treatment, but increased greatly in range after heat treatment. Nitinol (Unitek) had the greatest range of all wires tested (yield diameter of 8.7 mm for 0.016 inch Nitinol). Multistranded stainless steel wires had yield diameters between 9.0 and 14.0 mm.

Utilization of by-products from the tequila industry. Part 2: Potential value of Agave tequilana Weber azul leaves.

PubMed

Iñiguez-Covarrubias, G; Díaz-Teres, R; Sanjuan-Dueñas, R; Anzaldo-Hernández, J; Rowell, R M

2001-04-01

The leaves of the agave plant are left in the field after harvesting the heads for tequila production. Different types of agave leaves were isolated, classified, and their content in the total plant determined. The usable fractions were collected and their properties determined. Of the total wet weight of the agave plant, 54% corresponds to the agave head, 32% corresponds to materials which could be usable for sugar and fiber production which leaves 14% of the wet plant without apparent utility. The fractions with higher total reducing sugars (TRS) content were the fresh fraction of partially dry leaves stuck to the head and the leaf bases with a TRS content of 16.1% and 13.1%, respectively. The highest TRS concentration (16-28%) is in the agave head which is used for tequila production. The leaves are 90-120 cm long and 8-12 cm wide and contain fiber bundles that are 23-52 cm long and 0.6-13 mm wide. The ultimate fiber length is approximately 1.6 mm with an average width of 25 microns. There are several types of leaf fibers that can be utilized depending on what part of the plant they come from and what product is desired. Agave leaf fibers were pulped using a soda pulping process and the pulp was hand formed into test sheets. Test sheets made from pulped agave leaf fibers had a breaking length comparable to paper made from both pine and eucalyptus fibers, but the tear index and burst index were lower than the other two papers.

Atmospheric gradients from very long baseline interferometry observations

NASA Technical Reports Server (NTRS)

Macmillan, D. S.

1995-01-01

Azimuthal asymmetries in the atmospheric refractive index can lead to errors in estimated vertical and horizontal station coordinates. Daily average gradient effects can be as large as 50 mm of delay at a 7 deg elevation. To model gradients, the constrained estimation of gradient paramters was added to the standard VLBI solution procedure. Here the analysis of two sets of data is summarized: the set of all geodetic VLBI experiments from 1990-1993 and a series of 12 state-of-the-art R&D experiments run on consecutive days in January 1994. In both cases, when the gradient parameters are estimated, the overall fit of the geodetic solution is improved at greater than the 99% confidence level. Repeatabilities of baseline lengths ranging up to 11,000 km are improved by 1 to 8 mm in a root-sum-square sense. This varies from about 20% to 40% of the total baseline length scatter without gradient modeling for the 1990-1993 series and 40% to 50% for the January series. Gradients estimated independently for each day as a piecewise linear function are mostly continuous from day to day within their formal uncertainties.

Ophidascaris wangi sp. n. and O. najae (Gedoelst, 1916) (Ascaridida: Ascaridoidea) from snakes in China.

PubMed

Li, Liang; Guo, Yan-Ning; Li, Jian; Zhang, Lu-Ping

2014-12-01

Ophidascaris wangi sp. n. collected from the king rat snake Elaphe carinata (Günther) (Serpentes: Colubridae) in China is described using both light and scanning electron microscopy. The new species differs from its congeners in the presence of narrow lateral alae originating a short distance posterior to the base of the ventrolateral lips, its relatively long oesophagus (3.57-4.54 mm long, representing 6.6-7.6% of body length), its short spicules (1.89-2.14 mm long, representing 3.9-4.3% of body length), the number and arrangement of caudal papillae (49-57 pairs in total, arranged as follows: 43-51 pairs precloacal, 2 pairs joined paracloacal and 4 pairs postcloacal), the presence of a particular papilliform medioventral, postcloacal ornamentation and the morphology of the eggs and tip of the female tail. In addition, Ophidascaris najae (Gedoelst, 1916), collected from the king cobra Ophiophagus hannah Cantor (Serpentes: Elapidae) in China, is also redescribed. The morphology of the cervical papillae, labial denticles and phasmids of the female is described for the first time.

Prototype high speed optical delay line for stellar interferometry

NASA Astrophysics Data System (ADS)

Colavita, M. M.; Hines, B. E.; Shao, M.; Klose, G. J.; Gibson, B. V.

1991-12-01

The long baselines of the next-generation ground-based optical stellar interferometers require optical delay lines which can maintain nm-level path-length accuracy while moving at high speeds. NASA-JPL is currently designing delay lines to meet these requirements. The design is an enhanced version of the Mark III delay line, with the following key features: hardened, large diameter wheels, rather than recirculating ball bearings, to reduce mechanical noise; a friction-drive cart which bears the cable-dragging forces, and drives the optics cart through a force connection only; a balanced PZT assembly to enable high-bandwidth path-length control; and a precision aligned flexural suspension for the optics assembly to minimize bearing noise feedthrough. The delay line is fully programmable in position and velocity, and the system is controlled with four cascaded software feedback loops. Preliminary performance is a jitter in any 5 ms window of less than 10 nm rms for delay rates of up to 28 mm/s; total jitter is less than 10 nm rms for delay rates up to 20 mm/s.

3D geometrical assessment of femoral curvature: a reverse engineering technique.

PubMed

Chantarapanich, Nattapon; Sitthiseripratip, Kriskrai; Mahaisavariya, Banchong; Wongcumchang, Marut; Siribodhi, Pongwit

2008-09-01

Investigate the 2D/3D geometry of femoral curvature and femoral length using the advanced technique of computerized tomography combined with reverse engineering techniques. The present study was performed using reverse engineering technique based on CT data of 99 cadaveric femora. The femur was divided into three segments, proximal, mid-shaft, and distal regions by defining 35% and 65% of the femoral total length as a boundary of each region. The intramedullary canal in the mid-shaft region was mainly extracted to determine the set of circular center, which could consequence to approximate the 3D femoral radius of curvature using the 3D least square best fit. The 3D femoral curvature was then projected into A-P and M-L directions to investigate the correlation of 2D/3D femoral curvature as normal radiographic images. It was found that the average 3D Thai femoral curvature was 895.46-mm (SD = 238.06) and the average femoral total length is 421.96-mm (SD = 27.61). In addition, the 2D femoral curvature derived from sagittal radiographic image can be used to determine the 3D femoral curvature with this equation: R3D = RSagittal + 3.67 with r = 0.987. This described technique is a non-destructive method that can effectively assess the internal/ external 3D geometric data of the femur The obtained data is useful to develop a proper design of prosthesis that required inserting into the intramedullary canal. From the present study, it can be concluded that the 2DSagittal femoral curvature derived from standard radiographic image can be represented for the 3D femoral curvature.

Nasoalveolar molding improves appearance of children with bilateral cleft lip-cleft palate.

PubMed

Lee, Catherine T H; Garfinkle, Judah S; Warren, Stephen M; Brecht, Lawrence E; Cutting, Court B; Grayson, Barry H

2008-10-01

Bilateral cleft lip-cleft palate is associated with nasal deformities typified by a short columella. The authors compared nasal outcomes of cleft patients treated with banked fork flaps to those of patients who underwent nasoalveolar molding and primary retrograde nasal reconstruction. A retrospective review of 26 consecutive patients with bilateral cleft lip-cleft palate was performed. Group 1 patients (n = 13) had a cleft lip repair and nasal correction with banked fork flaps. Group 2 patients (n = 13) had nonsurgical columellar elongation with nasoalveolar molding followed by cleft lip closure and primary retrograde nasal correction. Group 3 patients (n = 13) were age-matched controls. Columellar length was measured at presentation and at 3 years of age. The number of nasal operations was recorded to 9 years. The Kruskal-Wallis and Tukey-Kramer tests were used for statistical analysis. Initial columellar length was 0.49 +/- 0.37 mm in group 1 and 0.42 +/- 0.62 mm in group 2. Post-nasoalveolar molding columellar length was 4.5 +/- 0.76 mm in group 2. By 3 years of age, columellar length was 3.03 +/- 1.47 mm in group 1, 5.98 +/- 1.09 mm in group 2, and 6.35 +/- 0.99 mm in group 3. Group 2 columellar length was significantly greater (p < 0.001) than that of group 1 and not statistically different from that of group 3 (p > 0.05). All group 1 patients (13 of 13) needed secondary nasal surgery. No nasoalveolar molding patients (zero of 13, group 2) required secondary nasal surgery. Nonsurgical columellar elongation with nasoalveolar molding followed by primary retrograde nasal reconstruction restored columellar length to normal by 3 years and significantly reduced the need for secondary nasal surgery.

Length asymmetry of the bovine digits.

PubMed

Muggli, E; Sauter-Louis, C; Braun, U; Nuss, K

2011-06-01

The lengths of the digital bones of the fore- and hind-limbs obtained post mortem from 40 cattle of different ages were measured using digital radiographs. The lengths of the individual digital bones and the overall length of the digit were determined using computer software. The lateral metacarpal/metatarsal condyle, and lateral P1 and P2 were significantly longer than their medial counterparts, whereas P3 of the medial digit was longer than its lateral partner. Measured from the cannon bone epiphysis to the tip of the pedal bone, the mean increased length of the lateral digit was 0.8 mm in the fore- and 1.5 mm in the hind-limb. When the lengths of the digital bones were summed, the mean length of the lateral digit was 1.8 mm longer in the fore-limb and 2.1 mm longer in the hind-limb. Based on these findings, it can be concluded that the lengths of the paired digits differ in cattle. The majority of cattle have longer lateral digits in the fore- and hind-limbs. This asymmetry might explain why the lateral hind-limb claws are predisposed to sole ulcers on hard surfaces. In the hind-limbs, the impact is transferred from the pelvis directly to the longer lateral digit. In the fore-limb claws, the tenomuscular attachment to the trunk may be involved in a more even weight distribution and in a shift of weight to the medial claw. Copyright © 2010 Elsevier Ltd. All rights reserved.

Post-assembly magnetization of a 100 kW high speed permanent magnet rotor.

PubMed

Lv, Yiliang; Wang, Guobin; Li, Liang

2015-03-01

A post-assembly magnetizing fixture has been designed and successfully used to magnetize the rotor of a 100 kW high speed permanent magnet synchronous motor. The rotor is a solid cylinder with outer diameter of 80 mm and total length of 515 mm. The permanent magnet material is samarium-cobalt (Sm2Co17) with saturation magnetizing field of 6 T. The mechanical stability of the magnetizing fixture has been studied as well as the general design methodology. The magnetizing coil is subdivided in order to reduce the electromagnetic force, and the coils are separately reinforced in different ways. The electromagnetic and structural optimization is performed by finite element analysis and verified by experiments.

Acetylcholine, carbachol, and GABA induce no detectable change in the length of isolated outer hair cells.

PubMed

Bobbin, R P; Fallon, M; Puel, J L; Bryant, G; Bledsoe, S C; Zajic, G; Schacht, J

1990-08-01

The mechanical and electrical properties of cochlear outer hair cells (OHCs) are suggested to modulate transduction by inner hair cells. These properties of OHCs are presumably regulated by efferent neurons which use several transmitters including acetylcholine (Ach) and gamma aminobutyric acid (GABA). Since it had been suggested that Ach causes isolated OHCs to shorten visibly, this study was designed to investigate whether GABA also alters the length of OHCs. OHCs were isolated from the guinea pig cochlea by mechanical dispersion after collagenase treatment. Cells were initially selected by strict morphological criteria. In addition they were only included in further studies if they attained a constant length during 10 min of superfusion with buffer solution. Neither GABA (20 microM: 100 microM), Ach (5 mM; 10 microM with 10 microM eserine) or carbachol (10 microM; 100 microM) altered OHC length when applied in iso-osmotic Hank's balanced salt solution (total number of cells tested, 72). If a change in length occurred it must have been smaller than 0.3 microns, our detection ability. In contrast, high potassium and variations in osmolarity changed hair cell length by 3-10% in agreement with other reports.

Control of arc length during gas metal arc welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madigan, R.B.; Quinn, T.P.

1994-12-31

An arc-length control system has been developed for gas metal arc welding (GMAW) under spray transfer welding conditions. The ability to monitor and control arc length during arc welding allows consistent weld characteristics to be maintained and therefore improves weld quality. Arc length control has only been implemented for gas tungsten arc welding (GTAW), where an automatic voltage control (AVC) unit adjusts torch-to-work distance. The system developed here compliments the voltage- and current-sensing techniques commonly used for control of GMAW. The system consists of an arc light intensity sensor (photodiode), a Hall-effect current sensor, a personal computer and software implementingmore » a data interpretation and control algorithms. Arc length was measured using both arc light and arc current signals. Welding current was adjusted to maintain constant arc length. A proportional-integral-derivative (PID) controller was used. Gains were automatically selected based on the desired welding conditions. In performance evaluation welds, arc length varied from 2.5 to 6.5 mm while welding up a sloped workpiece (ramp in CTWD) without the control. Arc length was maintained within 1 mm of the desired (5 mm ) with the control.« less

Comparison of the stability of various internal fixators used in the treatment of osteochondritis dissecans--a mechanical model.

PubMed

Morelli, Moreno; Poitras, Philippe; Grimes, Valentine; Backman, David; Dervin, Geoffrey

2007-04-01

The purpose of this study was to determine what characteristics of fixation devices used in the treatment of osteochondritis dissecans (OCD) contribute to improved stability to resist shear loading. An OCD model was designed using rigid polyurethane foam. Each specimen consisted of two components, an osteochondral fragment and a corresponding defect. A total of 40 specimens were prepared and assigned to one of four groups: control (no extrinsic stabilizer); two 2-mm-diameter Kirschner wires (K-wires), 40 mm in length; one threaded washer and a 28-mm screw; and one threaded washer and a 38 mm screw. Each specimen was mounted onto an Iosipescu shear test fixture and subjected to shear loads at a pseudo-static displacement rate of 0.075 mm/s. All groups demonstrated some stability; controls were significantly less stable than all other groups. The group with the threaded washer and 38-mm screw demonstrated the greatest stability (p < 0.001), and no difference was noted between the K-wire and 28-mm screw groups. These results suggest that, in this OCD model, friction conferred some intrinsic stability to resist loads in shear. However, stability was improved with the use of long implants that compressed the fragments together.

Relative contributions of neutral and non-neutral processes to clinal variation in calyx lobe length in the series Sakawanum (Asarum: Aristolochiaceae).

PubMed

Takahashi, Daiki; Teramine, Tsutomu; Sakaguchi, Shota; Setoguchi, Hiroaki

2018-01-25

Clines, the gradual variation in measurable traits along a geographical axis, play a major role in evolution and can contribute to our understanding of the relative roles of selective and neutral process in trait variation. Using genetic and morphological analyses, the relative contributions of neutral and non-neutral processes were explored to infer the evolutionary history of species of the series Sakawanum (genus Asarum), which shows significant clinal variation in calyx lobe length. A total of 27 populations covering the natural geographical distribution of the series Sakawanum were sampled. Six nuclear microsatellite markers were used to investigate genetic structure and genetic diversity. The lengths of calyx lobes of multiple populations were measured to quantify their geographical and taxonomic differentiation. To detect the potential impact of selective pressure, morphological differentiation was compared with genetic differentiation (QCT-FST comparison). Average calyx lobe length of A. minamitanianum was 124.11 mm, while that of A. costatum was 13.80 mm. Though gradually changing along the geographical axis within series, calyx lobe lengths were significantly differentiated among the taxa. Genetic differentiation between taxa was low (FST = 0.099), but a significant geographical structure along the morphological cline was detected. Except for one taxon pair, pairwise QCT values were significantly higher than the neutral genetic measures of FST and G'ST. Divergent selection may have driven the calyx lobe length variation in series Sakawanum taxa, although the underlying mechanism is still not clear. The low genetic differentiation indicates recent divergence and/or gene flows between geographically close taxa. These neutral processes would also affect the clinal variation in calyx lobe lengths. Overall, this study implies the roles of population history and divergent selection in shaping the current cline of a flower trait in the series Sakawanum. © The Author(s) 2017. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Growth and reproduction of the Japanese mantis shrimp, Oratosquilla oratoria (De Haan 1844) in the coastal area of Tongyeong, Korea

NASA Astrophysics Data System (ADS)

Kim, SeongEun; Kim, HanJu; Bae, HoJin; Kim, Hyeong-Gi; Oh, Chul-Woong

2017-06-01

Growth and reproduction of the Japanese mantis shrimp, Oratosquilla oratoria, were investigated in the Tongyeong, Korea from July 2014 to August 2015. A total of 2,621 samples (1,380 females and 1,241 males) were collected during the study period. Females were observed more frequently than males. The mean body length (BL) was 128.5 ± 0.38 mm in females and 126.9 ± 0.42 mm in males. The mean body weight (BW) was 31.2 ± 0.28 g in females and 31.1 ± 0.32 g in males. There was a significant difference in the length-frequency distribution between females and males. The relationship between BL and BW was lnBW = 2.85 × lnBL - 10.43 for females and lnBW = 2.87 × lnBL -10.52 for males. The gonadosomatic index (GSI) varied on a monthly basis. The GSI reached a maximum in May and a minimum in November. The highest values of the GSI coincided with the spawning period of O. oratoria. Larger individuals of O. oratoria have their spawning season earlier than smaller ones. The size at sexual maturity of females was estimated as 96.5 mm. The Von Bertalanffy growth function parameters were BL∞ = 184.5 mm, K = 0.72 year-1, C = 0.36 and WP = 0.45 for females and BL∞ = 183.75 mm, K = 0.82 year-1, C = 0.38 and WP = 0.22 for males. The growth of males was slightly faster than females. The present study will help with the fisheries management of O. oratoria based on ecological parameters.

[The sural medial perforator flap: Anatomical bases, surgical technique and indications in head and neck reconstruction].

PubMed

Struk, S; Schaff, J-B; Qassemyar, Q

2018-04-01

The medial sural artery perforator (MSAP) flap is defined as a thin cutaneo-adipose perforator flap harvested on the medial aspect of the leg. The aims of this study were to describe the anatomical basis as well as the surgical technique and discuss the indications in head and neck reconstructive surgery. We harvested 10 MSAP flap on 5 fresh cadavers. For each case, the number and the location of the perforators were recorded. For each flap, the length of pedicle, the diameter of source vessels and the thickness of the flap were studied. Finally, we performed a clinical application of a MSAP flap. A total of 23 perforators with a diameter superior than 1mm were dissected on 10 legs. The medial sural artery provided between 1 and 4 musculocutaneous perforators. Perforators were located in average at 10.3cm±2cm from the popliteal fossa and at 3.6cm±1cm from the median line of the calf. The mean pedicle length was 12.1cm±2.5cm. At its origin, the source artery diameter was 1.8mm±0.25mm and source veins diameters were 2.45mm±0.9mm in average. There was no complication in our clinical application. This study confirms the reliability of previous anatomical descriptions of the medial sural artery perforator flap. This flap was reported as thin and particularly adapted for oral cavity reconstruction and for facial or limb resurfacing. Sequelae might be reduced as compared to those of the radial forearm flap with comparable results. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Intrapetrous Internal Carotid Artery: Evaluation of Exposure, Mobilization and Surgical Maneuvers Feasibility from a Retrosigmoid Approach in a Cadaveric Model.

PubMed

Scerrati, Alba; Ercan, Serdar; Wu, Pengfei; Zhang, Jun; Ammirati, Mario

2016-07-01

To provide a quantification of the exposure of the vertical and horizontal segments of the intrapetrous carotid artery (IPCA) and to evaluate the possibilities of its mobilization and of performing surgical maneuvers on it using the retrosigmoid approach. Twelve surgical dissections were performed bilaterally on 6 fresh cadavers. Predissection computed tomography (CT) scans with bone fiducials for intraoperative navigation were acquired. A retrosigmoid craniectomy was performed. The inframeatal space was drilled, the horizontal (HoIPCA) and vertical (VeIPCA) segments of the IPCA were exposed, and their measurements were recorded. The carotid canal was enlarged, the artery was carefully detached from the bone, and a vessel loop was inserted in order to mobilize its horizontal segment. Afterwards we performed different surgical maneuvers: We inflated a 5-French Fogarty balloon to compress the IPCA and repaired a 7-mm arteriotomy with a running suture. Specimens underwent a new CT scan to evaluate the amount of bone removal and the integrity of the inner ear structures. The HoIPCA and VeIPCA were exposed and anatomically preserved in all specimens without injuring the surrounding neurovascular structures. The HoIPCA presented an average length of 24.89 mm (range: 19.41-31.47 mm), and the VeIPCA presented an average length of 10.07 mm (range: 8.92-11.58 mm). The possibility of IPCA mobilization and the feasibility of performing surgical maneuvers were demonstrated. Postdissection CT scan showed the preservation of inner ear structures. Exposure and mobilization of the IPCA using a retrosigmoid approach are feasible and could represent a viable option for the possibility of reaching a total resection of selected skull base tumors, even when involvement of the carotid canal is present. Published by Elsevier Inc.

Canal wall planning by engine-driven nickel-titanium instruments, compared with stainless-steel hand instrumentation.

PubMed

Tucker, D M; Wenckus, C S; Bentkover, S K

1997-03-01

Twenty-two mesial roots of extracted human mandibular molars were divided into two groups based on root curvature and length. The mesiolingual canals were instrumented using either Flexofiles in a step-back anticurvature filing method, or they were instrumented with engine-driven 0.02 taper nickel-titanium files. Ground sections were prepared at 1-, 2.5-, and 5-mm levels from the working length. The mesiobuccal canal was used as an uninstrumented control for predentin character. Digitizing software was used to calculate the instrumented portion as a percentage of the total canal perimeter. The results indicated no significant difference in overall canal wall planning between the two groups and no significant difference at each of the three levels.

Bypass of the maxillary artery to proximal middle cerebral artery.

PubMed

Ma, Lin; Ren, He-cheng; Huang, Ying

2015-03-01

The objective of this work was to explore the feasibility of bypass between the maxillary artery (MA) and proximity of middle cerebral artery (MCA). Ten fixed and perfused adult cadaver heads were dissected bilaterally, 20 sides in total. The superficial temporal artery and its 2 branches were dissected, and outer diameters were measured. The MA and its branch were exposed as well as deep temporal artery; outer diameter of MA was measured. The lengths between the external carotid artery, internal carotid artery, maxillary artery, and proximal middle cerebral artery were measured. Ten healthy adults as targets (20 sides), inner diameter and blood flow dynamic parameters of the common carotid artery, external carotid artery, internal carotid artery, maxillary artery, superficial temporal artery, and its 2 branches were done with ultrasound examination. The mean outer diameter of MA (2.60 ± 0.20 mm) was larger than that of the temporal artery trunk (1.70 ± 0.30 mm). The mean lengths of graft vessels between the internal carotid artery, external carotid artery, and the bifurcation section of MCA (171.00 ± 2.70 and 162.40 ± 2.60 mm) were longer than the mean lengths of graft vessels between MA and MCA bifurcation section (61.70 ± 1.50 mm). In adults, the mean blood flow of the second part of MA (62.70 ± 13.30 mL/min) was more than that of the 2 branches of the superficial temporal artery (15.90 ± 3.70 mL/min and 17.70 ± 4.10 ml/min). Bypass between the maxillary artery and proximity of middle cerebral artery is feasible. It is a kind of effective high flow bypass with which the graft vessel is shorter and straighter than the bypass between internal carotid artery or external carotid artery and proximity of middle cerebral artery.

New light-shielding technique for shortening the baffle length of a star sensor

NASA Astrophysics Data System (ADS)

Kawano, Hiroyuki; Sato, Yukio; Mitani, Kenji; Kanai, Hiroshi; Hama, Kazumori

2002-10-01

We have developed a star sensor with a short baffle of 140 mm. Our baffle provides a Sun rejection angle of 35 degrees with stray light attenuation less than the intensity level of a visual magnitude of Mv = +5 for a wide field of view lens of 13x13 degrees. The application of a new light shielding technique taking advantage of total internal reflection phenomena enables us to reduce the baffle length to about three fourths that of the conventional two-stage baffle. We have introduced two ideas to make the baffle length shorter. The one is the application of a nearly half sphere convex lens as the first focusing lens. The bottom surface reflects the scattering rays with high incident angles of over 50 degrees by using the total internal reflection phenomena. The other is the painting of the surface of the baffle with not frosted but gloss black paint. The gloss black paint enables most of the specular reflection rays to go back to outer space without scattering. We confirm the baffle performance mentioned above by scattering ray tracing simulation and a light attenuation experiment in a darkroom on the ground.

Heat transfer in GTA welding arcs

NASA Astrophysics Data System (ADS)

Huft, Nathan J.

Heat transfer characteristics of Gas Tungsten Arc Welding (GTAW) arcs with arc currents of 50 to 125 A and arc lengths of 3 to 11 mm were measured experimentally through wet calorimetry. The data collected were used to calculate how much heat reported to the cathode and anode and how much was lost from the arc column. A Visual Basic for Applications (VBA) macro was written to further analyze the data and account for Joule heating within the electrodes and radiation and convection losses from the arc, providing a detailed account of how heat was generated and dissipated within the system. These values were then used to calculate arc efficiencies, arc column voltages, and anode and cathode fall voltages. Trends were noted for variances in the arc column voltage, power dissipated from the arc column, and the total power dissipated by the system with changing arc length. Trends for variances in the anode and cathode fall voltages, total power dissipated, Joule heating within the torches and electrodes with changing arc current were also noted. In addition, the power distribution between the anode and cathode for each combination of arc length and arc current was examined. Keywords: Gas Tungsten Arc Welding, GTAW, anode fall, cathode fall, heat transfer, wet calorimetry

Gas transfer model to design a ventilator for neonatal total liquid ventilation.

PubMed

Bonfanti, Mirko; Cammi, Antonio; Bagnoli, Paola

2015-12-01

The study was aimed to optimize the gas transfer in an innovative ventilator for neonatal Total Liquid Ventilation (TLV) that integrates the pumping and oxygenation functions in a non-volumetric pulsatile device made of parallel flat silicone membranes. A computational approach was adopted to evaluate oxygen (O2) and carbon dioxide (CO2) exchanges between the liquid perfluorocarbon (PFC) and the oxygenating gas, as a function of the geometrical parameter of the device. A 2D semi-empirical model was implemented to this purpose using Comsol Multiphysics to study both the fluid dynamics and the gas exchange in the ventilator. Experimental gas exchanges measured with a preliminary prototype were compared to the simulation outcomes to prove the model reliability. Different device configurations were modeled to identify the optimal design able to guarantee the desired gas transfer. Good agreement between experimental and simulation outcomes was obtained, validating the model. The optimal configuration, able to achieve the desired gas exchange (ΔpCO2 = 16.5 mmHg and ΔpO2 = 69 mmHg), is a device comprising 40 modules, 300 mm in length (total exchange area = 2.28 m(2)). With this configuration gas transfer performance is satisfactory for all the simulated settings, proving good adaptability of the device. Copyright © 2015 IPEM. Published by Elsevier Ltd. All rights reserved.

[Distraction Osteogenesis is an Effective Method to Lengthen Digits in Congenital Malformations].

PubMed

Mann, M; Hülsemann, W; Winkler, F; Habenicht, R

2016-02-01

The aim of this study was to investigate the feasible amount of lengthening by distraction osteogenesis in congenital hand deficiencies. A total of 60 patients (1.6-17.8 years) underwent lengthening of 71 bones between 1994 and 2014. Bone lengthening was performed on 46 metacarpals and 25 phalanges. Mostly the first (n=30) and the fifth (n=21) rays were lengthened. Bone lengthening was performed to treat primarily symbrachydactyly (b=32) and amniotic band syndrome (n=10). To analyze the amount of lengthening preoperative radiographs and radiographs taken while removing the external fixator were compared. The charts were reviewed regarding age at surgery, duration of lengthening, duration of bony consolidation, complication, etc. The average of metacarpal distraction was 18.4 mm=73% lengthening with respect to the preoperative length; the average of phalange distraction was 14.0 mm=77% of the preoperative length. In both, metacarpals and phalanges, a lengthening of > 100% of the preoperative bone length was possible. In target length was reached in 89% of the procedures. The average time for consolidation was 6.1 (1-20) days/mm lengthening. The external fixator was in use on average for 140 (50-346) days. After removing of the external fixator an axial K-wire was used to stabilize the callus in 9 procedure, and an iliac bone craft plus axial K-wire in 11 procedures. The rate of complications was 30% (early consolidation, deviation, joint dislocation, pin infection, tendon dislocation). All complications could be treated without with acceptable results. Metacarpal and phalangeal distraction lengthening is an effective but demanding technique for ray reconstruction in congenital malformations of the hand. It is possible to lengthen a bone by more than 100%. Complications are common, but in most cases easy to handle. © Georg Thieme Verlag KG Stuttgart · New York.

The ROSETTA PHILAE Lander damping mechanism as probe for the Comet soil strength.

NASA Astrophysics Data System (ADS)

Roll, R.

2015-10-01

The ROSETTA Lander is equipped with an one axis damping mechanism to dissipate kinetic energy during the touch down. This damping is necessary to avoid damages to the Lander by a hard landing shock and more important to avoid re-bouncing from ground with high velocity. The damping mechanism works best for perpendicular impact, which means the velocity vector is parallel to the damper axis and all three feet touch the ground at the same time. That is usually not the case. Part of the impact energy can be transferred into rotational energy at ground contact if the impact is not perpendicular. This energy will lift up the Lander from the ground if the harpoons and the hold down thruster fail, as happen in mission. The damping mechanism itself is an electrical generator, driven by a spindle inside a telescopic tube. This tube was extended in mission for landing by 200mm. A maximum damping length of 140mm would be usually required to compensate a landing velocity of 1m/s, if the impact happens perpendicular on hard ground. After landing the potentiometer of the telescopic tube reading shows a total damping length of only 42,5mm. The damping mechanism and the overall mechanical behavior of the Lander at touch down are well tested and characterized and transferred to a multi-body computer model. The incoming and outgoing flightpath of PHILAE allow via computer-simulation the reconstruction of the touch down. It turns out, that the outgoing flight direction is dominated by the local ground slope and that the damping length is strongly dependent on the soil strength. Damping of soft comet ground must be included to fit the damping length measured. Scenario variations of the various feet contact with different local surface features (stone or regolith) and of different soil models finally lead to a restricted range for the soil strength at the touch down area.

Velocity of sarcomere shortening in rat cardiac muscle: relationship to force, sarcomere length, calcium and time.

PubMed

Daniels, M; Noble, M I; ter Keurs, H E; Wohlfart, B

1984-10-01

The relation between force and velocity was determined in sixteen trabeculae of rat right ventricle as a function of time during a twitch, of sarcomere length and of external Ca2+ concentration, [Ca2+]o. The trabeculae were studied in modified Krebs-Henseleit solution at 25 degrees C. Force was measured with a semiconductor strain gauge. Sarcomere length was measured with a laser diffraction system. A servomotor system was used in which control could be switched between sarcomere length, muscle length and force. Force-velocity relations were derived from load clamps and from contractions in which sarcomere length was initially held constant followed by a quick release and slower release of the sarcomeres at controlled velocity. Force-velocity relations were fitted by Hill's equation (Hill, 1938), (Po-P) b = (P+a) V, where P = force, V = velocity, Po = isometric force in mN/mm2 and a and b are constants. For [Ca2+]o = 2.5 mM, with both interventions the values (mean +/- S.D.) were: b = 1.00 +/- 0.45 micron/s; a = 9.52 +/- 5.60 mN/mm2; Vo measured = 13.6 +/- 3.0 micron/s; Vo calculated = 13.4 +/- 3.4 micron/s; Po measured = 96.5 +/- 25.0 mN/mm2; Po calculated = 119.3 +/- 34.5 mN/mm2. Vo rose with [Ca2+]o to a maximum at [Ca2+]o = 1.2 mM when Po was about 50% of maximum, while Po rose with [Ca2+]o to a maximum at above 2.5 mM. Vo rose with time during the twitch to a maximum at 25 ms following onset of contraction; Po was then about 50% of the maximum that was obtained at 120 ms. Vo increased with sarcomere length from zero at a sarcomere length of 1.6 micron to a maximum at 1.85 micron. Between 1.85 micron and 2.3 micron, Vo was constant. At 1.85 micron, Po was about 60% of maximum Po. These results are compatible with the hypothesis that Vo is more sensitive than Po to the amount of Ca2+ bound to the contractile proteins, and that Vo reaches a maximal value with an amount of Ca2+ bound to the contractile proteins at which Po has obtained only about 50% of its maximal value.

The influence of distal screw length on the primary stability of volar plate osteosynthesis--a biomechanical study.

PubMed

Baumbach, Sebastian F; Synek, Alexander; Traxler, Hannes; Mutschler, Wolf; Pahr, Dieter; Chevalier, Yan

2015-09-08

Extensor tendon irritation is one of the most common complications following volar locking plate osteosynthesis (VLPO) for distal radius fractures. It is most likely caused by distal screws protruding the dorsal cortex. Shorter distal screws could avoid this, yet the influence of distal screw length on the primary stability in VLPO is unknown. The aim of this study was to compare 75 to 100% distal screw lengths in VLPO. A biomechanical study was conducted on 11 paired fresh-frozen radii. HRpQCT scans were performed to assess bone mineral density (BMD) and bone mineral content (BMC). The specimens were randomized pair-wise into two groups: 100% (group A) and 75% (group B) unicortical distal screw lengths. A validated fracture model for extra-articular distal radius fractures (AO-23 A3) was used. Polyaxial volar locking plates were mounted, and distal screws was inserted using a drill guide block. For group A, the distal screw tips were intended to be flush or just short of the dorsal cortex. In group B, a target screw length of 75% was calculated. The specimens were tested to failure using a displacement-controlled axial compression test. Primary biomechanical stability was assessed by stiffness, elastic limit, and maximum force as well as with residual tilt, which quantified plastic deformation. Nine specimens were tested successfully. BMD and BMC did not differ between the two groups. The mean distal screw length of group A was 21.7 ± 2.6 mm (range: 16 to 26 mm), for group B 16.9 ± 1.9 mm (range: 12 to 20 mm). Distal screws in group B were on average 5.6 ± 0.9 mm (range: 3 to 7 mm) shorter than measured. No significant differences were found for stiffness (706 ± 103 N/mm vs. 660 ± 124 N/mm), elastic limit (177 ± 25 N vs. 167 ± 36 N), maximum force (493 ± 139 N vs. 471 ± 149 N), or residual tilt (7.3° ± 0.7° vs. 7.1° ± 1.3°). The 75% distal screw length in VLPO provides similar primary stability to 100% unicortical screw length. This study, for the first time, provides the biomechanical basis to choose distal screws significantly shorter then measured.

Distribution, reproduction, and feeding of West African shrimp Plesionika carinata Holthuis, 1951 (Decapoda, Pandalidae)

NASA Astrophysics Data System (ADS)

Burukovsky, R. N.

2017-09-01

Plesionika carinata is endemic in the West African tropical biogeographical realm and is distributed from the western Sahara coast (23°35' N) to southern Namibia (29° S). A total of 263 individuals with a total carapace length of 31 to 71 mm have been studied. P. carinata juveniles are pelagic and occur over depths from 340 to 2000 m or more, mainly over the lower part of the continental slope in summer and over the upper part of the continental slope in autumn. Adults are mainly benthic and occur on the edge of the shelf and the upper part of the continental slope (at depths of 300 to 880 m). Ovigerous females have 750 to 3330 eggs 0.45-0.5 × 0.5-0.65 mm in size on pleopods. Plesionika carinata feeds on abundant micronectonic and macroplanktonic crustaceans (euphausiids and pelagic shrimps) at earlier pelagic stages; it is detritophagous/necrophagous and predatory near the bottom when adult.

Relation between the axial length and lenticular progressive myopia.

PubMed

Lin, H-Y; Chang, C-W; Wang, H-Z; Tsai, R-K

2005-08-01

To investigate the possible risk factors associated with lenticular progressive myopia and to compare the differences between patients with lenticular progressive myopias and senile cataracts. We retrospectively reviewed cases that had been diagnosed as lenticular progressive myopia with a discrete nuclear sclerotic cataract and progressive myopic changes in one hospital from January 1998 to February 2003. A total of 47 eyes of 35 patients were enrolled in this study. In all, 32 eyes of 29 cases of common senile cataract receiving cataract extraction surgery during the study period were randomly chosen (every four cases in time sequence within a 2-month period by two ophthalmologists' clinic in 2002) as the control group. We compared the preoperative refraction status, keratometry (K-values) and axial lengths between these two groups. The possible ocular or systemic associating diseases were also investigated in the study group. In the lenticular progressive myopia group, the mean age at surgery (52.9+/-9.2 years) is younger than that in the senile cataract group (68.1+/-7.3 years). The mean axial length in the study group (25.68+/-1.93 mm) is statistically significant longer than that in the control group (22.97+/-0.83 mm) (P<0.0001). Besides, patients with lenticular progressive myopia had significantly lower mean K-values (43.25+/-1.42 diopters) than patients with senile cataracts (44.25+/-1.28 diopters) (P<0.01). There were no other ocular or systemic diseases closely associated with lenticular progressive myopia. Patients with nuclear cataract combined with lenticular progressive myopia have longer axial length than patients with senile cataract. The longer axial length may be one of the important risk factors predisposing to lenticular progressive myopia.

Performance modeling of a wearable brain PET (BET) camera

NASA Astrophysics Data System (ADS)

Schmidtlein, C. R.; Turner, J. N.; Thompson, M. O.; Mandal, K. C.; Häggström, I.; Zhang, J.; Humm, J. L.; Feiglin, D. H.; Krol, A.

2016-03-01

Purpose: To explore, by means of analytical and Monte Carlo modeling, performance of a novel lightweight and low-cost wearable helmet-shaped Brain PET (BET) camera based on thin-film digital Geiger Avalanche Photo Diode (dGAPD) with LSO and LaBr3 scintillators for imaging in vivo human brain processes for freely moving and acting subjects responding to various stimuli in any environment. Methods: We performed analytical and Monte Carlo modeling PET performance of a spherical cap BET device and cylindrical brain PET (CYL) device, both with 25 cm diameter and the same total mass of LSO scintillator. Total mass of LSO in both the BET and CYL systems is about 32 kg for a 25 mm thick scintillator, and 13 kg for 10 mm thick scintillator (assuming an LSO density of 7.3 g/ml). We also investigated a similar system using an LaBr3 scintillator corresponding to 22 kg and 9 kg for the 25 mm and 10 mm thick systems (assuming an LaBr3 density of 5.08 g/ml). In addition, we considered a clinical whole body (WB) LSO PET/CT scanner with 82 cm ring diameter and 15.8 cm axial length to represent a reference system. BET consisted of distributed Autonomous Detector Arrays (ADAs) integrated into Intelligent Autonomous Detector Blocks (IADBs). The ADA comprised of an array of small LYSO scintillator volumes (voxels with base a×a: 1.0 <= a <= 2.0 mm and length c: 3.0 <= c <= 6.0 mm) with 5-65 μm thick reflective layers on its five sides and sixth side optically coupled to the matching array of dGAPDs and processing electronics with total thickness of 50 μm. Simulated energy resolution was 10.8% and 3.3% for LSO and LaBr3 respectively and the coincidence window was set at 2 ns. The brain was simulated as a sphere of uniform F-18 activity with diameter of 10 cm embedded in a center of water sphere with diameter of 10 cm. Results: Analytical and Monte Carlo models showed similar results for lower energy window values (458 keV versus 445 keV for LSO, and 492 keV versus 485 keV for LaBr3), and for the relative performance of system sensitivity. Monte Carlo results further showed that the BET geometry had >50% better noise equivalent count (NEC) performance relative to the CYL geometry, and >1100% better performance than a WB geometry for 25 mm thick LSO and LaBr3. For 10 mm thick LaBr3 equivalent mass systems LSO (7 mm thick) performed ~40% higher NEC than LaBr3. Analytic and Monte Carlo simulations also showed that 1×1×3 mm scintillator crystals can achieve ~1.2 mm FWHM spatial resolution. Conclusions: This study shows that a spherical cap brain PET system can provide improved NEC while preserving spatial resolution when compared to an equivalent dedicated cylindrical PET brain camera and shows greatly improved PET performance relative to a conventional whole body PET/CT. In addition, our simulations show that LSO will generally outperform LaBr3 for NEC unless the timing resolution for LaBr3 is considerably smaller than presently used for LSO, i.e. well below 300 ps.

The Volumetric Imaging System for the Ionosphere (VISION)

DTIC Science & Technology

2011-01-01

telescope mirror is an 80 mm focal length, 50 mm diameter, first surface mirror with magnesium fluoride over aluminum coating on a zerodur blank...will be either a wedge–and–strip anode or a codacon. The telescope mirror is an 80 mm focal length, 2.5 cm diameter, first surface mirror with...magnesium fluoride over aluminum coating on a zerodur blank. The filters are the three reflection bandpass filters developed for and flown on

Stress Distribution Around Single Short Dental Implants: A Finite Element Study.

PubMed

Vidya Bhat, S; Premkumar, Priyanka; Kamalakanth Shenoy, K

2014-12-01

Bone height restrictions are more common in the posterior regions of the mandible, because of either bone resorption resulting from tooth loss or even anatomic limitations, such as the position of the inferior alveolar nerve. In situations where adequate bone height is not available in the posterior mandible region, smaller lengths of implants may have to be used but it has been reported that the use of long implants (length ≥10 mm) is a positive factor in osseointegration and authors have reported failures with short implants. Hence knowledge about the stress generated on the bone with different lengths of implants needs scientific evaluation. The purpose of this study was to compare and evaluate the influence of different lengths of implants on stress upon bone in mandibular posterior area. A 3 D finite element model was made of the posterior mandible using the details from a CT scan, using computer software (ANSYS 12). Four simulated implants with lengths 6 mm, 8 mm, 10 mm and 13 mm were placed in the centre of the bone. A static vertical force of 250 N and a static horizontal force of 100 N were applied. The stress generated in the cortical and cancellous bone around the implant were recorded and evaluated with the help of ANSYS. In this study, Von Mises stress on a 6 mm implant under a static vertical load of 250 N appeared to be almost in the same range of 8 and 10 mm implant which were more as compared to 13 mm implant. Von Mises stress on a 6mm implant under a static horizontal load of 100 N appeared to be less when compared to 8, 10 and 13 mm implants. From the results obtained it may be inferred that under static horizontal loading conditions, shorter implants receive lesser load and thus may tend to transfer more stresses to the surrounding bone. While under static vertical loading the shorter implants bear more loads and comparatively transmit lesser load to the surrounding bone.

Measurement of LYSO Intrinsic Light Yield Using Electron Excitation

NASA Astrophysics Data System (ADS)

Turtos, Rosana Martinez; Gundacker, Stefan; Pizzichemi, Marco; Ghezzi, Alessio; Pauwels, Kristof; Auffray, Etiennette; Lecoq, Paul; Paganoni, Marco

2016-04-01

The determination of the intrinsic light yield (LYint) of scintillating crystals, i.e. number of optical photons created per amount of energy deposited, constitutes a key factor in order to characterize and optimize their energy and time resolution. However, until now measurements of this quantity are affected by large uncertainties and often rely on corrections for bulk absorption and surface/edge state. The novel idea presented in this contribution is based on the confinement of the scintillation emission in the central upper part of a 10 mm cubic crystal using a 1.5 MeV electron beam with diameter of 1 mm. A black non-reflective pinhole aligned with the excitation point is used to fix the light extraction solid angle (narrower than total reflection angle), which then sets a light cone travel path through the crystal. The final number of photoelectrons detected using a Hamamatsu R2059 photomultiplier tube (PMT) was corrected for the extraction solid angle, the Fresnel reflection coefficient and quantum efficiency (QE) of the PMT. The total number of optical photons produced per energy deposited was found to be 40000 ph/MeV ± 9% (syst) ±3% (stat) for LYSO. Simulations using Geant4 were successfully compared to light output measurements of 2 × 2 mm2 section crystals with lengths of 5-30 mm, in order to validate the light transport model and set a limit on Light Transfer Efficiency estimations.

Variations in Flexural Strength of Heat-polymerized Acrylic Resin after the Usage of Denture Cleansers.

PubMed

Ragher, Mallikarjuna; Vinayakumar, G; Patil, Sanketsopan; Chatterjee, Aishwarya; Mallikarjuna, D M; Dandekeri, Savita; Swetha, V; Pradeep, M R

2016-04-01

The objective of this study was to evaluate and compare changes in the flexural strength of heat-cured denture base resins when treated using denture cleansers. A total of 40 specimens with dimension 65 mm length, 10 mm width, and 3 mm thickness were prepared as per ISO 1567 specification. A total of 10 specimens were immersed in distilled water to be used as control. Of the remaining 30 samples, 10 were treated with Clinsodent, 10 with VI-Clean, and 10 with Clanden denture cleansers. Specimens in each group were subjected to three-point flexural load in universal testing machine at a cross-head speed of 5 mm/min. The peak load (N) was recorded and flexural strength was calculated. The findings were analyzed using Kruskal-Wallis analysis of variance and Mann-Whitney test. Heat-cured denture base resin selected for this study showed significant difference in flexural strength after immersion in denture cleansers Clinsodent, VI-Clean, and Clanden solutions, when compared with the control group. Findings of this study showed that denture cleansers altered the flexural strength of heat polymerized acrylic resins that endured soaking cycles which simulated 180 days of use. Hence, denture cleansers should be used with caution, once a day after brushing the dentures. It is advisable for patients to follow the manufacturer's instructions.

[Feeding ecology of Conger myriaster and structure of the food webs in artificial reef zone, Laoshan Bay, China].

PubMed

Liu, Hong Yan; Sun, Tong Tong; Zeng, Xiao Qi; Zhang, Pei Dong; Li, Wen Tao; Zhang, Xiu Mei

2018-04-01

Based on cage net and longline fishing surveys in Laoshan Bay, China, from April 2015 to January 2017, a total of 279 Conger myriaster stomach samples were analyzed to study their feeding ecology, including diet composition, feeding type, feeding grade, feeding intensity, trophic niche, and trophic level. The stomach content analysis of nine key fish species (including Sebastes schlegelii, Hexagrammos otakii, Hexagrammos agrammus, Sebastiscus mamoratus, Lateolabrax maculatus, etc.), were conducted to examine the food webs in artificial reef zone. The results showed that the diet of C. myriaster consisted of more than 30 species belonging to seven orders, in which shrimps were the most dominant prey species, followed by fishes and cephalopods. The dominant species in the diet of C. myriaster were H.otakii, Enedrias fangi, Trachypenaeus curvirostris, Ammodytes personatus and Alpheus japonicas. The diet composition of C. myriaster varied with season and anal length. Fishes and shrimps were the two important groups throughout the years. Cephalopods were predominant in spring. Cephalopods and crabs were predominant in Autumn. Fish eggs were eaten mostly during winter. Fish eggs and T. curvirostris were the dominant prey groups of the C. myriaster with anal length ≤120 mm, whereas A. personatus and A. japonicas were the dominant prey groups of the C. myriaster with anal length 120-130 mm, H.otakii and E.fangi were the dominant prey of the C. myriaster with anal length ＞130 mm. The percentage of empty stomach of C. myriaster varied significantly with season, but the mean stomach fullness index did not. The percentage of empty stomach and mean stomach fullness index did not differ significantly among different anal length groups. The trophic levels of the key fish species were higher than level 3, with C. myriaster at the top of food webs (with a trophic level of 4.636). Decapoda, crabs, amphipoda and molluscs were the main prey of key fish species, while Crustaceans, E. fangi, H. otakii and A. personatus were the main preys of L. maculatus and C. myriaster.

Influence of Gender and Age on Upper-Airway Length During Development

PubMed Central

Ronen, Ohad; Malhotra, Atul; Pillar, Giora

2008-01-01

OBJECTIVE Obstructive sleep apnea has a strong male predominance in adults but not in children. The collapsible portion of the upper airway is longer in adult men than in women (a property that may increase vulnerability to collapse during sleep). We sought to test the hypothesis that in prepubertal children, pharyngeal airway length is equal between genders, but after puberty boys have a longer upper airway than girls, thus potentially contributing to this change in apnea propensity. METHODS Sixty-nine healthy boys and girls who had undergone computed tomography scans of their neck for other reasons were selected from the computed tomography archives of Rambam and Carmel hospitals. The airway length was measured in the midsagittal plane and defined as the length between the lower part of the posterior hard palate and the upper limit of the hyoid bone. Airway length and normalized airway length/body height were compared between the genders in prepubertal (4- to 10-year-old) and postpubertal (14- to 19-year-old) children. RESULTS In prepubertal children, airway length was similar between boys and girls (43.2 ± 5.9 vs 46.8 ± 7.7 mm, respectively). When normalized to body height, airway length/body height was significantly shorter in prepubertal boys than in girls (0.35 ± 0.03 vs 0.38 ± 0.04 mm/cm). In contrast, postpubertal boys had longer upper airways (66.5 ± 9.2 vs 52.2 ± 7.0 mm) and normalized airway length/body height (0.38 ± 0.05 vs 0.33 ± 0.05 mm/cm) than girls. CONCLUSIONS Although boys have equal or shorter airway length compared with girls among prepubertal children, after puberty, airway length and airway length normalized for body height are significantly greater in boys than in girls. These data suggest that important anatomic changes at puberty occur in a gender-specific manner, which may be important in explaining the male predisposition to pharyngeal collapse in adults. PMID:17908723

Systematic Occlusion of Shunts: Control of Early Postoperative IOP and Hypotony-related Complications Following Glaucoma Shunt Surgery.

PubMed

Sharkawi, Eamon; Artes, Paul H; Oleszczuk, Justyna D; Bela, Cyrielle; Achache, Farid; Barton, Keith; Bergin, Ciara

2016-01-01

Evaluation of a protocol of total intraluminal occlusion of Baerveldt shunts and its effects on early postoperative intraocular pressure (IOP) control and hypotony-related complications. This was a noncomparative, prospective, and interventional study. Glaucoma patients were recruited to undergo Baerveldt shunt surgery. A total of 116 eyes of 112 patients were enrolled. During shunt implantation, aqueous outflow was restricted using an intraluminal occluding stent inserted through the entire tube length, with and without external ligation, to halt aqueous flow. Postoperatively, eyes underwent ligature laser suture lysis and partial or complete stent removals, at predetermined time intervals. Loss of postoperative IOP control was categorized as transient or persistent hypotony (IOP≤5 mm Hg) or hypertony (IOP>21 mm Hg). Patients were followed up for 1 year. Preoperatively median IOP was 23 mm Hg (mean 26 mm Hg, SD 12 mm Hg), median number of glaucoma medications was 3.0 (mean 3.0, SD 1.2). During year 1, laser suture lysis was performed in 30 eyes (26%) and stent removal in 93 eyes (80%) (23 partial; 70 complete). There was 1 case of transient hypotony, no cases of persistent hypotony, 10 of transient hypertony, and 3 of persistent hypertony. Nine eyes had IOP≤5 mm Hg at ≥1 time points and hypotony-related complications occurred in 8 eyes (7%). At 1 year, median IOP was 12 mm Hg (mean 13 mm Hg, SD 4 mm Hg) with a median of 1.0 glaucoma medications (mean 1.1, SD 1.3). The cumulative probability of failure during the first 12 months follow-up was 6% (n=7). Overall postoperative complications occurred in 11 eyes (9%). The surgical and postoperative protocol resulted in controlled, step-wise reductions of IOP with low rates of hypotony and related complications.

Whole eye axial biometry during accommodation using ultra-long scan depth optical coherence tomography

PubMed Central

Zhong, Jianguang; Tao, Aizhu; Xu, Zhe; Jiang, Hong; Shao, Yilei; Zhang, Huicheng; Liu, Che; Wang, Jianhua

2014-01-01

PURPOSE To investigate changes of whole eye axial biometry during accommodation using ultra-long scan depth optical coherence tomography (UL-OCT). DESIGN Prospective, observational case series. METHODS Twenty-one adult subjects were enrolled. Using UL-OCT, the left eye of each subject was imaged with relaxed (0 D) and accommodative stimuli (+6 D). Full eye biometry included central corneal thickness (CCT), anterior chamber depth (ACD), lens thickness, vitreous length and axial length (AL). RESULTS During accommodation (+6 D), the axial biometry of the whole eye changed significantly. Compared to the rest state, ACD at the accommodative state decreased significantly from 3.128 ± 0.305 mm to 2.961 ± 0.298 mm (paired t-test, P < 0.001). The lens thickness increased significantly from 3.723 ± 0.237 mm to 3.963 ± 0.234 mm (P < 0.001). The vitreous length decreased significantly from 17.129 ± 0.864 mm to 17.057± 0.848 mm (P < 0.001). AL was 24.519 ± 0.917 mm at the rest state and increased to 24.545±0.915 mm with +6 D accommodation stimulus. The elongated AL of 26.1 ± 13.4 μm between the rest and accommodative states was significant (P < 0.001). CONCLUSIONS During accommodation, whole eye axial biometry changed, including a decrease in ACD and vitreous length, and an increase in lens thickness and AL. UL-OCT provides an alternative method that is suitable for full eye biometry during accommodation. PMID:24487051

Cost Analysis of Endoscopic Mucosal Resection vs Surgery for Large Laterally Spreading Colorectal Lesions.

PubMed

Jayanna, Mahesh; Burgess, Nicholas G; Singh, Rajvinder; Hourigan, Luke F; Brown, Gregor J; Zanati, Simon A; Moss, Alan; Lim, James; Sonson, Rebecca; Williams, Stephen J; Bourke, Michael J

2016-02-01

Large laterally spreading lesions (LSL) in the colon and rectum can be safely and effectively removed by endoscopic mucosal resection (EMR). However, many patients still undergo surgery. Endoscopic treatment may be more cost effective. We compared the costs of endoscopic versus surgical management of large LSL. We performed a prospective, observational, multicenter study of consecutive patients referred to 1 of 7 academic hospitals in Australia for the management of large LSL (≥ 20 mm) from January 2010 to December 2013. We collected data on numbers of patients undergoing EMR, actual endoscopic management costs (index colonoscopy, hospital stay, adverse events, and first surveillance colonoscopy), characteristics of patients and lesions, outcomes, and adverse events, and findings from follow-up examinations 14 days, 4-6 months, and 16-18 months after treatment. We compared data from patients who underwent EMR with those from a model in which all patients underwent surgery without any complications. Event-specific costs, based on Australian refined diagnosis-related group codes, were used to estimate average cost per patient. EMR was performed on 1489 lesions (mean size, 36 mm) in 1353 patients (mean age, 67 years; 52.1% male). Total costs involved in the endoscopic management of large LSL were US $6,316,593 and total inpatient hospitalization length of stay was 1180 days. The total cost predicted for the surgical management group was US $16,601,502, with a total inpatient hospitalization length of stay of 4986 days. Endoscopic management produced a potential total cost saving of US $10,284,909; the mean cost difference per patient was US $7602 (95% confidence interval, $8458-$9220; P < .001). Inpatient hospitalization length of stay was reduced by 2.81 nights per patient (95% confidence interval, 2.69-2.94; P < .001). In a large multicenter study, endoscopic management of large LSL by EMR was significantly more cost-effective than surgery. Endoscopic management by EMR at an appropriately experienced and resourced tertiary center should be considered the first line of therapy for most patients with this disorder. This approach is likely to deliver substantial overall health expenditure savings. ClinicalTrials.gov, Number: NCT01368289. Copyright © 2016 AGA Institute. Published by Elsevier Inc. All rights reserved.

Seat and seatbelt accommodation in fire apparatus: Anthropometric aspects.

PubMed

Hsiao, Hongwei; Whitestone, Jennifer; Wilbur, Michael; Lackore, J Roger; Routley, J Gordon

2015-11-01

This study developed anthropometric information on U.S. firefighters to guide fire-apparatus seat and seatbelt designs and future standards development. A stratified sample of 863 male and 88 female firefighters across the U.S. participated in the study. The study results suggested 498 mm in width, 404 mm in depth, and 365-476 mm in height for seat pans; 429-522 mm in width and 542 mm in height for seat back; 871 mm in height for head support; a seat space of 733 mm at shoulder and 678 mm at hip; and a knee/leg clearance of 909 mm in fire truck cab. Also, 1520 mm of lap belt web effective length and 2828 mm of lap-and-shoulder belt web effective length were suggested. These data for fire-truck seats and seatbelts provide a foundation for fire apparatus manufacturers and standards committees to improve firefighter seat designs and seatbelt usage compliance. Published by Elsevier Ltd.

Normative dimensions and symmetry of the lacrimal drainage system on dacryocystography: statistical analysis of morphometric characteristics.

PubMed

Horsburgh, A; Massoud, T F

2013-05-01

Asymmetric lacrimal flow occurs in females more than males. We hypothesised that the normal lacrimal drainage system (LDS) may show subtle left-right asymmetry in morphometry when imaged on dacryocystography (DCG). We retrospectively reviewed 60 normal bilateral LDSs.Images were analysed for 7 parameters: (1) combined length of either the superior or inferior canaliculus plus common canaliculus, (2) angle of insertion of common canaliculus into lacrimal sac (LS), (3, 4) length and width of the LS, (5) length of the naso lacrimal duct (NLD), and (6, 7) width of proximal and distal NLD. We tested the effect of independent variables (age, gender, and side) on each dependent variable (length, width, or angle) using regression analysis. We used a Studentt-test for independent samples to statistically compare bilateral LDSs. Patient median age was 62 years, and male:female ratio was 27:73. Mean dimensions and angles for all LDSs were: (1) 14.5 mm, (2) 57°,(3) 11.6 mm, (4) 2.1 mm, (5) 20.7 mm, (6) 1.4 mm, and (7) 1.8 mm. No independent variable affected variation in length, width, or angle. No significant difference emerged between dimensions of right and left LDSs in both sexes. A degree of affective lateralisation in the brain is known to result in lacrimal flow asymmetry after mood manipulation. We show that this is not reflected in LDS anatomy. Moreover, our detailed morphometric data can aid in therapeutic planning of LDS luminal procedures, especially when DCG images of one LDS are used as a road map for contralateral interventions.

A Model for Fiber Length Attrition in Injection-Molded Long-Fiber Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

TuckerIII, Charles L.; Phelps, Jay H; El-Rahman, Ahmed Abd

2013-01-01

Long-fiber thermoplastic (LFT) composites consist of an engineering thermoplastic matrix with glass or carbon reinforcing fibers that are initially 10 to 13 mm long. When an LFT is injection molded, flow during mold filling orients the fibers and degrades the fiber length. Fiber orientation models for injection molding are well developed, and special orientation models for LFTs have been developed. Here we present a detailed quantitative model for fiber length attrition in a flowing fiber suspension. The model tracks a discrete fiber length distribution (FLD) at each spatial node. Key equations are a conservation equation for total fiber length, andmore » a breakage rate equation. The breakage rate is based on buckling of fibers due to hydrodynamic forces, when the fibers are in unfavorable orientations. The FLD model is combined with a mold filling simulation to predict spatial and temporal variations in fiber length distribution in a mold cavity during filling. The predictions compare well to experiments on a glassfiber/ PP LFT molding. Fiber length distributions predicted by the model are easily incorporated into micromechanics models to predict the stress-strain behavior of molded LFT materials. Author to whom correspondence should be addressed; electronic mail: ctucker@illinois.edu 1« less

Direct and indirect effects of glomalin, mycorrhizal hyphae, and roots on aggregate stability in rhizosphere of trifoliate orange.

PubMed

Wu, Qiang-Sheng; Cao, Ming-Qin; Zou, Ying-Ning; He, Xin-hua

2014-07-25

To test direct and indirect effects of glomalin, mycorrhizal hyphae, and roots on aggregate stability, perspex pots separated by 37-μm nylon mesh in the middle were used to form root-free hyphae and root/hyphae chambers, where trifoliate orange (Poncirus trifoliata) seedlings were colonized by Funneliformis mosseae or Paraglomus occultum in the root/hyphae chamber. Both fungal species induced significantly higher plant growth, root total length, easily-extractable glomalin-related soil protein (EE-GRSP) and total GRSP (T-GRSP), and mean weight diameter (an aggregate stability indicator). The Pearson correlation showed that root colonization or soil hyphal length significantly positively correlated with EE-GRSP, difficultly-extractable GRSP (DE-GRSP), T-GRSP, and water-stable aggregates in 2.00-4.00, 0.50-1.00, and 0.25-0.50 mm size fractions. The path analysis indicated that in the root/hyphae chamber, aggregate stability derived from a direct effect of root colonization, EE-GRSP or DE-GRSP. Meanwhile, the direct effect was stronger by EE-GRSP or DE-GRSP than by mycorrhizal colonization. In the root-free hyphae chamber, mycorrhizal-mediated aggregate stability was due to total effect but not direct effect of soil hyphal length, EE-GRSP and T-GRSP. Our results suggest that GRSP among these tested factors may be the primary contributor to aggregate stability in the citrus rhizosphere.

Release and velocity of micronized dexamethasone implants with an intravitreal drug delivery system: kinematic analysis with a high-speed camera.

PubMed

Meyer, Carsten H; Klein, Adrian; Alten, Florian; Liu, Zengping; Stanzel, Boris V; Helb, Hans M; Brinkmann, Christian K

2012-01-01

Ozurdex, a novel dexamethasone (DEX) implant, is released by a drug delivery system into the vitreous cavity. We analyzed the mechanical release aperture of the novel applicator, obtained real-time recordings using a high-speed camera system and performed kinematic analysis of the DEX application. Experimental study. : The application of intravitreal DEX implants (6 mm length, 0.46 mm diameter; 700 μg DEX mass, 0.0012 g total implant mass) was recorded by a high-speed camera (500 frames per second) in water (Group A: n = 7) or vitreous (Group B: n = 7) filled tanks. Kinematic analysis calculated the initial muzzle velocity as well as the impact on the retinal surface at approximately 15 mm of the injected drug delivery system implant in both groups. A series of drug delivery system implant positions was obtained and graphically plotted over time. High-speed real-time recordings revealed that the entire movement of the DEX implant lasted between 28 milliseconds and 55 milliseconds in Group A and 1 millisecond and 7 milliseconds in Group B. The implants moved with a mean muzzle velocity of 820 ± 350 mm/s (±SD, range, 326-1,349 mm/s) in Group A and 817 ± 307 mm/s (±SD, range, 373-1,185 mm/s) in Group B. In both groups, the implant gradually decelerated because of drag force. With greater distances, the velocity of the DEX implant decreased exponentially to a complete stop at 13.9 mm to 24.7 mm in Group A and at 6.4 mm to 8.0 mm in Group B. Five DEX implants in Group A reached a total distance of more than 15 mm, and their calculated mean velocity at a retinal impact of 15 mm was 408 ± 145 mm/s (±SD, range, 322-667 mm/s), and the consecutive normalized energy was 0.55 ± 0.44 J/m (±SD). In Group B, none of the DEX implants reached a total distance of 6 mm or more. An accidental application at an angle of 30 grade and consecutively reduced distance of approximately 6 mm may result in a mean velocity of 844 and mean normalized energy of 0.15 J/m (SD ± 0.47) in a water-filled eye. The muzzle velocity of DEX implants is approximately 0.8 m/s and decreases exponentially over distance. The drag over time in vitreous is faster than in water. The calculated retinal impact energy does not reach reported damage levels for direct foreign bodies or other projectiles.

Atmospheric phase characteristics of the ALMA long baseline

NASA Astrophysics Data System (ADS)

Matsushita, Satoki; Asaki, Yoshiharu; Fomalont, Edward B.; Barkats, Denis; Corder, Stuartt A.; Hills, Richard E.; Kawabe, Ryohei; Maud, Luke T.; Morita, Koh-Ichiro; Nikolic, Bojan; Tilanus, Remo P. J.; Vlahakis, Catherine

2016-07-01

Atacama Large Millimeter/submillimeter Array (ALMA) is the world's largest millimeter/ submillimeter (mm / Submm) interferometer. Along with science observations, ALMA has performed several long baseline campaigns in the last 6 years to characterize and optimize its long baseline capabilities. To achieve full long baseline capability of ALMA, it is important to understand the characteristics of atmospheric phase fluctuation at long baselines, since it is believed to be the main cause of mm/submm image degradation. For the first time, we present detailed properties of atmospheric phase fluctuation at mm/submm wavelength from baselines up to 15 km in length. Atmospheric phase fluctuation increases as a function of baseline length with a power-law slope close to 0.6, and many of the data display a shallower slope (02.-03) at baseline length greater than about 15 km. Some of the data, on the other hand, show a single slope up to the maximum baseline length of around 15 km. The phase correction method based on water vapor radiometers (WVRs) works well, especially for cases with precipitable water vapor (PWV) greater than 1 mm, typically yielding a 50% decrease or more in the degree of phase fluctuation. However, signicant amount of atmospheric phase fluctuation still remains after the WVR phase correction: about 200 micron in rms excess path length (rms phase fluctuation in unit of length) even at PWV less than 1 mm. This result suggests the existence of other non-water-vapor sources of phase fluctuation. and emphasizes the need for additional phase correction methods, such as band-to-band and/or fast switching.

Fetal sigmoid colon mesentery - In relevance in fetal ultrasound application. A pilot study.

PubMed

Wozniak, Slawomir; Florjanski, Jerzy; Kordecki, Henryk; Podhorska-Okolow, Marzena; Domagala, Zygmunt

2018-03-01

Ultrasound examinations during pregnancy are routine procedures used to detect fetal congenital malformations. Ultrasound monitoring of sigmoid colon mesenterial development could be useful for early detection of subjects at risk of sigmoid colon volvulus. The aim of our paper was to assess the sigmoid colon length, and sigmoid colon mesentery width and height in the late fetal period, and, using the results, to estimate the surface area of the mesocolon (in mm 2 ) in living fetuses. Moreover, we attempted to repeat some of these measurements in living fetuses using ultrasound imaging. The study was carried out on 209 formalin fixed human fetuses (100 female and 109 male) aged from 4th to 7th gestational months (102-203 days), with a crown-rump length of 132-342mm. The length of the sigmoid colon, as well as the height and width of its mesentery were measured. The surface area of the mesocolon was estimated. Correction for formalin induced shrinkage was applied. Pilot ultrasound examinations of live fetuses were performed. Mean values of sigmoid colon length, mesenteric width and height (formalin fixed fetuses) for respective gestational ages were: month 4: 21.46±6.7mm, 6.80±2.1mm, 5.5±1.49mm; month 5: 27.32±1.2mm, 7.62±2.01mm, 7.33±2.17mm; month 6: 47.56±9.57mm, 11.68±3.8mm, 10.3±3.05mm; month 7: 56.92±17.48mm. 15.32±8 mm, 12.81±3.16mm. The surface area ranges of the sigmoid colon mesentery found for respective gestational months (intrauterine fetuses) were as follows: month 4: 33.24-51.95mm 2 ; month 5: 49.63-77.6mm 2 ; month 6: 106.89-167.15mm 2 and month 7: 145.69-272.53mm 2 . The surface area of the sigmoid colon mesentery can be used as a simple parameter applied in fetal ultrasonographic evaluation. The development of the sigmoid colon accelerates in the 6th gestational month, and decelerates in the 7th gestational month. The sigmoid colon mesentery width was larger than its height between the 4th and 7th gestational months. Copyright © 2017 Elsevier GmbH. All rights reserved.

[Growth of Strombus gigas (Gastropoda: Strombidae) snail in 4 environments of Quintana Roo, Mexico].

PubMed

Navarrete, A J

2001-03-01

The growth rate of queen conch cultured in pens was studied from October 1993 to March 1994. Sixteen pens (50 m2 each, four pens per environment), were set in four environments: Thalassia, Thalassia-sand, Sand and Coral within a reef lagoon on Punta Gavilan and Banco Chinchorro. Twenty conchs were introduced in each pen (sizes: 100-120, 120-140, 140-160 and 160-180 mm shell length) and measured monthly to the nearest mm. Growth rate was assessed by two methods: a) shell marginal mean increase and b) the Gulland-Holt method considering all conch within pens. In the first method, the environment Sand had the highest growth (3.21 +/- 0.26 mm/month) at Punta Gavilan, whereas at Banco Chinchorro, highest growth was recorded in Coral (2.31 +/- 0.44 mm/month). Considering the second method, highest asymptotic length conch in Punta Gavilan occurred in Thalassia-sand (287.5 mm), whereas in Banco Chinchorro the highest asymptotic length was measured in Sand (318.1 mm). There were significant differences in growth between sites; juvenile growth is related with habitat quality mainly food availability.

Changes in ocular biomechanics after femtosecond laser creation of a laser in situ keratomileusis flap.

PubMed

Leccisotti, Antonio; Fields, Stefania V; Moore, Johnny; Shah, Sunil; Moore, Tara C B

2016-01-01

To evaluate ocular biomechanical parameters with the Corvis ST, a noncontact tonometer combined with an ultra-high-speed Scheimpflug camera, before and after creation of a femtosecond laser-created laser in situ keratomileusis (LASIK) flap. Private practice, Siena, Italy. Prospective consecutive study. Right eyes of patients having LASIK were assessed with the dynamic Scheimpflug camera before and after femtosecond laser (LDV Z4) flap creation but before mechanical flap lifting. Twenty-eight eyes of 28 patients were evaluated. Before flap creation, the mean values on the dynamic Scheimpflug camera were intraocular pressure (IOP), 15.04 mm Hg ± 3.99 (SD); central pachymetry, 550.8 ± 101.0 μm; applanation 1 length, 1.721 ± 0.134 mm; applanation 2 length, 1.674 ± 0.287 mm; applanation 1 velocity, 0.126 ± 0.031 m/s; and deflection amplitude, 1.039 ± 0.141 mm. After flap creation, the mean values were IOP, 16.10 ± 3.11 mm Hg (95% confidence interval [CI], 0.44-1.78; P < .05); central pachymetry, 561.8 ± 35.9 μm (95% CI, -28.9 to 50.9; P = .21); applanation 1 length, 1.789 ± 0.1492 mm (95% CI, 0.003-0.134; P < .05); applanation 2 length, 1.759 ± 0.259 mm (95% CI, -0.005 to 0.173; P = .08); applanation 1 velocity, 0.136 ± 0.022 m/s (95% CI, 0.001-0.017; P < .05); and deflection amplitude, 1.029 ± 0.151 mm (95% CI: -0.043 to 0.025; P = .34). The dynamic Scheimpflug camera showed changes in biomechanical properties after femtosecond creation of a LASIK flap as indicated by an increased applanation 1 length and applanation 1 velocity. No author has a financial or proprietary interest in any material or method mentioned. Copyright © 2016 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Comparison between submucosal tunneling endoscopic resection and video-assisted thoracoscopic surgery for large esophageal leiomyoma originating from the muscularis propria layer.

PubMed

Tan, Yuyong; Lv, Liang; Duan, Tianying; Zhou, Junfeng; Peng, Dongzi; Tang, Yao; Liu, Deliang

2016-07-01

Submucosal tunneling endoscopic resection (STER) has been proved to be safe and effective for removal of esophageal leiomyoma originating from the muscularis propria (MP) layer. However, there are still technical challenges for tumors ≥35 mm due to the limited space of the submucosal tunnel. The aim of the study was to estimate the safety and efficacy of STER for large esophageal leiomyoma originating from the MP layer as well as compare its efficacy with video-assisted thoracoscopic surgery (VATS), which is a standard procedure for treating esophageal leiomyoma. We retrospectively collected the clinical data of the patients with esophageal leiomyoma of 35-55 mm who underwent STER or VATS at our hospital between January 2010 and December 2014. Epidemiological data (gender, age), tumor location, tumor size, procedure-related parameters, complications, length of stay and cost were compared between STER and VATS. A total of 31 patients were enrolled, and 18 patients underwent STER and the other 13 received VATS. There was no significant difference between the two groups in gender, age, tumor location, tumor size, complications and rate of en bloc resection (P > 0.05). However, patients in the STER groups had a shorter operation time, a less decrease in hemoglobin level, a shorter length of hospital stay and a decreased cost (P < 0.05). No recurrence was noted in the STER and VATS groups during a mean follow-up of 10.9 and 30.8 months, respectively. The treatment efficacy was comparable between the STER and VATS for esophageal leiomyoma of 35-55 mm. However, STER is superior to VATS in a shorter operation time, a less decrease in hemoglobin level, a shorter length of hospital stay and a decreased cost.

Cyclic fatigue resistance of RaCe and Mtwo rotary files in continuous rotation and reciprocating motion.

PubMed

Vadhana, Sekar; SaravanaKarthikeyan, Balasubramanian; Nandini, Suresh; Velmurugan, Natanasabapathy

2014-07-01

The purpose of this study was to evaluate and compare the cyclic fatigue resistance of RaCe (FKG Dentaire, La Chaux-de-Fonds, Switzerland) and Mtwo (VDW, Munich, Germany) rotary files in continuous rotation and reciprocating motion. A total of 60 new rotary Mtwo and RaCe files (ISO size = 25, taper = 0.06, length = 25 mm) were selected and randomly divided into 4 groups (n = 15 each): Mtc (Mtwo NiTi files in continuous rotation), Rc (RaCe NiTi files in continuous rotation), Mtr (Mtwo NiTi files in reciprocating motion), and Rr (RaCe NiTi files in reciprocating motion). A cyclic fatigue testing device was fabricated with a 60° angle of curvature and a 5-mm radius. All instruments were rotated or reciprocated until fracture occurred. The time taken for each instrument to fracture and the length of the broken fragments were recorded. All the fractured files were analyzed under a scanning electron microscope to detect the mode of fracture. The Kolmogorov-Smirnov test was used to assess the normality of samples distribution, and statistical analysis was performed using the independent sample t test. The time taken for the instruments of the Mtr and Rr groups to fail under cyclic loading was significantly longer compared with the Mtc and Rc groups (P < .001). Scanning electron microscopic observations showed that the instruments of all groups had undergone a ductile mode of fracture. The length of the fractured segments was between 5 and 6 mm, which was not statistically significant among the experimental groups. Mtwo and RaCe rotary instruments showed a significantly higher cyclic fatigue resistance in reciprocating motion compared with continuous rotation motion. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Time Outdoors and Myopia Progression Over 2 Years in Chinese Children: The Anyang Childhood Eye Study.

PubMed

Li, Shi-Ming; Li, He; Li, Si-Yuan; Liu, Luo-Ru; Kang, Meng-Tian; Wang, Yi-Peng; Zhang, Fengju; Zhan, Si-Yan; Gopinath, Bamini; Mitchell, Paul; Wang, Ningli

2015-07-01

To investigate whether time outdoors and a range of other activities are associated with change in spherical equivalent (SE) and axial length in Chinese children over a period of 2 years. A total of 1997 children aged 12.7 ± 0.5 (10.9-15.6) years in the Anyang Childhood Eye Study (ACES) were examined annually (baseline and two follow-up visits). Myopia was defined as cycloplegic SE < -0.50 diopters (D). Questionnaires were administered to the students and parents at baseline to gauge time spent outdoors and on other tasks. We ran mixed linear models including age, sex, and years of follow-up. In the full cohort of children there was a suggestive association between time spent outdoors and change in axial length; however, the effect size was very small (high versus low tertile: -0.016 mm/y, P = 0.053). The association was observed in children not myopic at baseline (high versus low tertile, -0.036 mm/y; P = 0.009) but not in those already myopic at baseline (high versus low tertile: -0.005 mm/y; P = 0.595). Time outdoors and change in SE showed similar, but nonsignificant, relationships (P > 0.05), perhaps due to insufficient statistical power. The other activities examined and parental myopia were not associated with changes in SE and axial length (P > 0.11). Within the normal range of variation encountered in these Chinese children, a wide range of activities were largely unrelated to myopia progression at this age. However, there was suggestive evidence that greater time outdoors was associated with slower axial elongation in nonmyopic teenagers, but not in existing myopes.

The deep-sea zooplankton of the North, Central, and South Atlantic: Biomass, abundance, diversity

NASA Astrophysics Data System (ADS)

Vereshchaka, Alexander; Abyzova, Galina; Lunina, Anastasia; Musaeva, Eteri

2017-03-01

Ocean-scale surveys of vertical distribution of the zooplankton from the surface to the bathypelagic zone along transects are quite rare in the North Atlantic and absent in the Equatorial and South Atlantic. We present the first deep-sea quantitative survey of the zooplankton in the Equatorial and South Atlantic, analyze the interaction between environment (depth, water masses, surface productivity) and zooplankton abundance and biomass, and assess the biodiversity and role of copepods in various deep strata. Samples were taken at 20 sites along a submeridional transect between 40°N and 30°S at four discrete depth strata: epi- meso-, upper- and lower- bathypelagic. A closing Bogorov-Rass plankton net (1 m2 opening, 500 μm mesh size, towed at a speed of 1 m s-1) was used and three major plankton groups were defined: non-gelatinous mesozooplankton (mainly copepods and chaetognaths; 1-30 mm length), gelatinous mesozooplankton (mainly siphonophorans, medudae and salps; individual or zooid; 1-30 mm length) and macroplankton (mainly shrimps; over 30 mm length). Over 300 plankton taxa were identified, among which 243 belonged to Copepoda. Two-dimensional distribution (latitude versus depth zone) of major group biomass, total copepod abundance, and abundance of dominant species is presented as well as distribution of biodiversity parameters (number of species, Shannon and 'dominance' indices). Biomass and abundance of all major groups were depth-dependent. The number of taxa (N) was depended on surface productivity, diversity of the communities was strongly linked to depth, whilst 'evenness' was independant upon both variables. Each of depth strata was inhabited by distinct copepod assemblages, which significantly differed from each other. The paper is concluded with brief descriptions of the deep Atlantic plankton communities from studied strata.

Quantitative Gross and CT measurements of Cadaveric Cervical Vertebrae (C3 – C6) as Guidelines for the Lateral mass screw fixation

PubMed Central

Heinneman, Thomas E.; Conti, Mathew S.; Dossous, Paul-Michel F.; Dillon, David J.; Tsiouris, Apostolos J.; Pyo, Se Young; Mtui, Estomih P.; Härtl, Roger

2016-01-01

Background Lateral mass screw fixation is the treatment of choice for posterior cervical stabilization. Long or misdirected screws carry a risk of injury to spinal nerve roots or vertebral artery. This study was aimed to assess the gross anatomic and CT measurements of typical cervical vertebrae for the selection of lateral mass screws. Methods Dimensions of the articular pillars were measured on 1) Dry cervical vertebrae with Vernier calipers and 2) Multiplanar reformations of CT scans of the same vertebrae with Viewer software package. The data was statistically evaluated. Results The transverse diameter of the articular pillars with Vernier calipers varied from 6.0 to 15.4 mm (mean=10.5 mm ± 1.5) and on CT scans ranged from 8.2 – 16.1 mm (mean=11.6 mm ± 1.4). The antero-posterior diameter, an estimate of the screw length by Roy-Camille technique varied from 3.9 to 12.7 mm (mean=8.6 mm ± 1.6) by Vernier calipers and from 6.4 to 13.3 mm (mean=9.1 ± 1.2) on CT scans. The oblique AP diameter, an estimate of screw length by Magerl method varied from 10.8 to 20.3 mm (mean=14.9 mm ± 1.8) by Vernier calipers and from 11.4 to 19.3 mm (mean=14.5 mm ± 1.7) on CT. The CT measurements for height, transverse and AP diameter of the articular pillars were 0.5 - 1.0 mm larger than dimensions by Vernier calipers. No statistically significant difference was observed between the caliper and CT measurements for the oblique AP diameter. Conclusion CT measurements of the articular pillars may slightly overestimate the desired screw length selected by spine surgeons when compared to actual anatomy. Although means of the articular pillars correspond to the screw lengths used, substantial number of observations below 10 mm for Roy-Camille trajectory and below 14 mm for Magerl trajectory requires careful preoperative planning and intra-operative confirmation to avoid long/misdirected lateral mass screws. PMID:28377857

Ventricular flow dynamics with varying LVAD inflow cannula lengths: In-silico evaluation in a multiscale model.

PubMed

Liao, Sam; Neidlin, Michael; Li, Zhiyong; Simpson, Benjamin; Gregory, Shaun D

2018-04-27

Left ventricular assist devices are associated with thromboembolic events, which are potentially caused by altered intraventricular flow. Due to patient variability, differences in apical wall thickness affects cannula insertion lengths, potentially promoting unfavourable intraventricular flow patterns which are thought to be correlated to the risk of thrombosis. This study aimed to present a 3D multiscale computational fluid dynamic model of the left ventricle (LV) developed using a commercial software, Ansys, and evaluate the risk of thrombosis with varying inflow cannula insertion lengths in a severely dilated LV. Based on a HeartWare HVAD inflow cannula, insertion lengths of 5, 19, 24 and 50 mm represented cases of apical hypertrophy, typical ranges of apical thicknesses and an experimental length, respectively. The risk of thrombosis was evaluated based on blood washout, residence time, instantaneous blood stagnation and a pulsatility index. By introducing fresh blood to displace pre-existing blood in the LV, after 5 cardiac cycles, 46.7%, 45.7%, 45.1% and 41.8% of pre-existing blood remained for insertion lengths of 5, 19, 24 and 50 mm, respectively. Compared to the 50 mm insertion, blood residence time was at least 9%, 7% and 6% higher with the 5, 19 and 24 mm insertion lengths, respectively. No instantaneous stagnation at the apex was observed directly after the E-wave. Pulsatility indices adjacent to the cannula increased with shorter insertion lengths. For the specific scenario studied, a longer insertion length, relative to LV size, may be advantageous to minimise thrombosis by increasing LV washout and reducing blood residence time. Copyright © 2018 Elsevier Ltd. All rights reserved.

[The effect of size reduction of corn silage on feed intake, milk production and milk composition of cows].

PubMed

Preissinger, W; Schwarz, F J; Kirchgessner, M

1998-01-01

In three experiments (E1, E2, E3) maize silage of different physical structure and of different stage of maturity at harvest were fed to 24 (E1), 36 (E2) or 28 (E3) dairy cows. The cows were fed individually over an experimental period of five or six weeks. The maize silages had a mean DM content of 28% (E1), 32% (E2) or 36% (E3). At the stage of harvest, the stovers and the cobs had a mean DM content of < 22% (E1, E2) or 27% (E3), 40% (E1), 46% (E2) or 57% (E3), respectively. The maize was harvested with a chopping length of 4 and 8 mm (E1, E3) and of 6 and 8 mm (E2), without corn cracking (E1) or with and without corn cracking (E2, E3). The daily feed ration consisted of ad libitum offered maize silage, 1.7 kg DM hay, soya bean meal (E2, E3) and concentrate. The different chopping length of 4 mm, 6 mm or 8 mm had no effect on the maize silage intake in E1 and E2. In E3 the daily maize silage intake increased by about 1.2 kg DM per cow at a chopping length of 4 mm in comparison to 8 mm, whereas only the treatment with the combination of 4 mm chopping length and corn cracking showed a significant increase in DMI. The corn cracking improved the milk yield significantly (E2) or in a tendency (E3) at 2.0 kg (E2) or at 1.6 kg (E2), while the variation of chopping length had no effect on milk yield. The different physical structure did not influence the milk fat content with mean values of 4.65% (E1), 4.15% (E2) and 4.10% (E3), respectively. The milk protein content decreased in E2 feeding maize silage with a chopping length of 8 mm and corn cracking; but in E1 and E3 no effect was seen on protein content with mean values of 3.66% (E1) or 3.51% (E2).

Morphology-related limitations of EVAR applicability in the treatment of AAA in West-Central Poland.

PubMed

Dzieciuchowicz, Łukasz; Tomczak, Jolanta; Strauss, Ewa; Oszkinis, Grzegorz

2018-05-14

To analyze the current applicability of endovascular aneurysm repair (EVAR) in patients with an infrarenal abdominal aortic aneurysm (AAAs) with indication for elective treatment in West-Central Poland. Computed tomography angiograms of 100 consecutive patients with infrarenal AAA deemed to require treatment were analyzed with an OsiriX DICOM viewer in 3D-MPR mode. Proximal neck diameter, length, angulation, shape, the presence of thrombus and calcification, distal neck diameter, and morphology of the iliac arteries were determined. Three sets of morphological criteria were established. The optimal criteria consisted of a non-conical proximal neck without moderate or severe calcification or thrombus, with a diameter of 18-28 mm, length of ≥15 mm, and β angulation of <60%; a distal neck with a diameter of ≥20 mm; a landing zone in the common iliac arteries with a length of ≥ 10 mm and diameter of ≤ 20 mm; and external iliac arteries with diameters of ≥7 mm. The suboptimal criteria included proximal neck diameters of 18-32 mm, neck lengths ≥10 mm, infrarenal neck angulations of up to 75˚, and common iliac artery diameters of up to 25 mm. Finally, the extended suboptimal criteria included proximal neck diameters of 16-34 mm and infrarenal neck angulations ≤90˚, without limits in the maximal diameter of the common iliac arteries. The median maximum aneurysm diameter was 61 mm. The optimal, suboptimal, and extended suboptimal criteria were met by 23%, 32%, and 53% of patients, respectively. The most common deviations were wide, conical, and angulated proximal necks and aneurysmal iliac arteries. The majority of patients with AAA deemed to be candidates for elective repair do not meet the most favorable criteria for EVAR. Availability of better endovascular solutions for conical, angulated, and wide necks and aneurysmal iliac arteries would likely expand EVAR applicability. Open repair remains a valid option. Copyright © 2018 Elsevier Inc. All rights reserved.

Boundary layer control by a fish: Unsteady laminar boundary layers of rainbow trout swimming in turbulent flows

PubMed Central

Saarenrinne, Pentti

2016-01-01

ABSTRACT The boundary layers of rainbow trout, Oncorhynchus mykiss [0.231±0.016 m total body length (L) (mean±s.d.); N=6], swimming at 1.6±0.09 L s−1 (N=6) in an experimental flow channel (Reynolds number, Re=4×105) with medium turbulence (5.6% intensity) were examined using the particle image velocimetry technique. The tangential flow velocity distributions in the pectoral and pelvic surface regions (arc length from the rostrum, lx=71±8 mm, N=3, and lx=110±13 mm, N=4, respectively) were approximated by a laminar boundary layer model, the Falkner−Skan equation. The flow regime over the pectoral and pelvic surfaces was regarded as a laminar flow, which could create less skin-friction drag than would be the case with turbulent flow. Flow separation was postponed until vortex shedding occurred over the posterior surface (lx=163±22 mm, N=3). The ratio of the body-wave velocity to the swimming speed was in the order of 1.2. This was consistent with the condition of the boundary layer laminarization that had been confirmed earlier using a mechanical model. These findings suggest an energy-efficient swimming strategy for rainbow trout in a turbulent environment. PMID:27815242

Boundary layer control by a fish: Unsteady laminar boundary layers of rainbow trout swimming in turbulent flows.

PubMed

Yanase, Kazutaka; Saarenrinne, Pentti

2016-12-15

The boundary layers of rainbow trout, Oncorhynchus mykiss [0.231±0.016 m total body length (L) (mean±s.d.); N=6], swimming at 1.6±0.09 L s -1 (N=6) in an experimental flow channel (Reynolds number, Re=4×10 5 ) with medium turbulence (5.6% intensity) were examined using the particle image velocimetry technique. The tangential flow velocity distributions in the pectoral and pelvic surface regions (arc length from the rostrum, l x =71±8 mm, N=3, and l x =110±13 mm, N=4, respectively) were approximated by a laminar boundary layer model, the Falkner-Skan equation. The flow regime over the pectoral and pelvic surfaces was regarded as a laminar flow, which could create less skin-friction drag than would be the case with turbulent flow. Flow separation was postponed until vortex shedding occurred over the posterior surface (l x =163±22 mm, N=3). The ratio of the body-wave velocity to the swimming speed was in the order of 1.2. This was consistent with the condition of the boundary layer laminarization that had been confirmed earlier using a mechanical model. These findings suggest an energy-efficient swimming strategy for rainbow trout in a turbulent environment. © 2016. Published by The Company of Biologists Ltd.

Percutaneous distraction lengthening in brachymetacarpia.

PubMed

Volpi, Alexander D; Fragomen, Austin T

2011-08-08

Brachymetacarpia is a condition manifesting a shortened metacarpal that is caused by early closure of the epiphyseal plate and believed to arise idiopathically. The correction for brachymetacarpia is usually for cosmetic reasons as brachymetacarpia does not impair function. The literature indicates several different approaches to lengthening digits, including single-stage lengthening and rapid distraction lengthening with a bone graft. However, gradual distraction is the preferred method due to excellent cosmetic outcomes and few postoperative complications. This article reports a case of brachymetacarpia treated with distraction lengthening using a minimally invasive, percutaneous approach. A 16-year-old girl presented with a shortened left ring finger and underwent surgery to correct the deformity. The left ring finger measured 12 mm shorter than her right ring finger; however, there was normal mobility at the joints. In the operating room, an external fixator was attached using 4 self-drilling, self-tapping pins through several 3-mm skin incisions. The total fixation time was 14 weeks; however, the achieved length of 12 mm was achieved 6 weeks postoperatively. The healing index of the fixation period was 81 days/cm. The postoperative course and fixation period were uneventful, with no complications except for 2 pin infections that were treated with oral antibiotics. The method of gradual distraction lengthening in this case successfully achieved the desired length and yielded an excellent cosmetic result. Copyright 2011, SLACK Incorporated.

Radiographic study of the fifth metatarsal for optimal intramedullary screw fixation of Jones fracture.

PubMed

Ochenjele, George; Ho, Bryant; Switaj, Paul J; Fuchs, Daniel; Goyal, Nitin; Kadakia, Anish R

2015-03-01

Jones fractures occur in the relatively avascular metadiaphyseal junction of the fifth metatarsal (MT), which predisposes these fractures to delayed union and nonunion. Operative treatment with intramedullary (IM) screw fixation is recommended in certain cases. Incorrect screw selection can lead to refractures, nonunion, and cortical blowout fractures. A better understanding of the anatomy of the fifth MT could aid in preoperative planning, guide screw size selection, and minimize complications. We retrospectively identified foot computed tomographic (CT) scans of 119 patients that met inclusion criteria. Using interactive 3-dimensional (3-D) models, the following measurements were calculated: MT length, "straight segment length" (distance from the base of the MT to the shaft curvature), and canal diameter. The diaphysis had a lateroplantar curvature where the medullary canal began to taper. The average straight segment length was 52 mm, and corresponded to 68% of the overall length of the MT from its proximal end. The medullary canal cross-section was elliptical rather than circular, with widest width in the sagittal plane and narrowest in coronal plane. The average coronal canal diameter at the isthmus was 5.0 mm. A coronal diameter greater than 4.5 mm at the isthmus was present in 81% of males and 74% of females. To our knowledge, this is the first anatomic description of the fifth metatarsal based on 3-D imaging. Excessive screw length could be avoided by keeping screw length less than 68% of the length of the fifth metatarsal. A greater than 4.5 mm diameter screw might be needed to provide adequate fixation for most study patients since the isthmus of the medullary canal for most were greater than 4.5 mm. Our results provide an improved understanding of the fifth metatarsal anatomy to guide screw diameter and length selection to maximize screw fixation and minimize complications. © The Author(s) 2014.

Short mandible - a possible risk factor for cleft palate with/without a cleft lip.

PubMed

Hermann, N V; Darvann, T A; Ersbøll, B K; Kreiborg, S

2014-05-01

To estimate the influence of a short mandible on the risk of developing a cleft palate with/without a cleft lip (CP). The retrospective sample consisted of 115 2-month-old Danish infants with CP, and 70 control infants with unilateral incomplete cleft lip (UICL). Cephalometric X-rays were obtained. Mandibular length (Lm ) was measured and corrected for body length (Lb ) to remove influence of varying body length in the sample. Logistic regression was applied to the corrected mandibular length (Lmc ) to calculate the risk of having a cleft palate. The mean mandibular length in the group with CP was about 4 mm shorter than in the control group. Odds ratio (OR) was calculated to be 0.58 (95% confidence interval 0.48-0.68), implying that an individual's risk of cleft palate with/without a cleft lip increases about 50% per mm decrease in mandibular length. A special facial type including a short mandible is a possible risk factor for cleft palate, and it was found that the risk of cleft palate increases 58% per mm decreases in mandibular length. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Consecutive unsplinted implant-supported restorations to replace lost multiple adjacent posterior teeth: A 4-year prospective cohort study.

PubMed

Lee, Jung-Tae; Lee, Hyo-Jung; Park, Shin-Young; Kim, Hae-Young; Yeo, In-Sung

2015-08-01

The aim of this study was to investigate the various events occurring in unsplinted implant restoration in posterior jaws during a period of 4 years. From August 2008 to April 2009, eight volunteers (three men and five women) who had two or more consecutively missing teeth received 20 implants in posterior maxillae and mandibles. Unsplinted single crowns were delivered to each implant. For the 4-year follow-up periods, patients were enrolled in a maintenance schedule at 1, 3, 6, 12, 24, 36 and 48 months. The data, including a questionnaire, radiography, mobility and probing were recorded on regular check-ups. A total of 20 implants in eight patients were followed up for 48 months, showing a 100% survival rate. Mean marginal bone loss around implants was 0.26 mm. Statistical analysis revealed insignificant correlation between metal-ceramic and zirconia-ceramic crowns and among implant lengths (8.5 mm, 10 mm and 11.5 mm). Mean probing depths were similar or insignificantly different, regardless of the materials used or length of implants. The most frequent complications, in decreasing order, were food impaction (65%) and porcelain chipping (45%), sensitivity (25%), pain (20%) and loose contact (15%). Compared with metal-ceramic crowns, zirconia-ceramic crowns showed more unfavorable cases of porcelain chipping (p=0.017), pain (p=0.007) and loose contact with an adjacent crown (p=0.031). Within the limits of the sample size, this study showed that unsplinted implant-supported single restorations to replace consecutive posterior missing teeth may function well.

2D FEA of evaluation of micromovements and stresses at bone-implant interface in immediately loaded tapered implants in the posterior maxilla

PubMed Central

Desai, Shrikar R.; Singh, Rika; Karthikeyan, I.

2013-01-01

Aim: The aim of the study is to evaluate the influence implant length on stress distribution at bone implant interface in single immediately loaded implants when placed in D4 bone quality. Materials and Methods: A 2-dimensional finite element models were developed to simulate two types of implant designs, standard 3.75 mm–diameter tapered body implants of 6 and 10 mm lengths. The implants were placed in D4 bone quality with a cortical bone thickness of 0.5 mm. The implant design incorporated microthreads at the crestal part and the rest of the implant body incorporated Acme threads. The Acme thread form has a 29° thread angle with a thread height half of the pitch; the apex and valley are flat. A 100 N of force was applied vertically and in the oblique direction (at an angle of 45°) to the long axis of the implants. The respective material properties were assigned. Micro-movements and stresses at the bone implant interface were evaluated. Results: The results of total deformation (micro-movement) and Von mises stress were found to be lower for tapered long implant (10 mm) than short implant (6 mm) while using both vertical as well as oblique loading. Conclusion: Short implants can be successfully placed in poor bone quality under immediate loading protocol. The novel approach of the combination of microthreads at the crestal portion and acme threads for body portion of implant fixture gave promising results. PMID:24174759

Alternative acceptance criteria of girth weld defects in cross country pipelines. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denys, R.M.; Lefevre, T.

1997-06-01

The failure behaviour of defective girth welds in large diameter pipe lines was assessed using radiographic and mechanised ultrasonic inspection, small scale (tensile, hardness, Charpy and CTOD) and wide plate tests. The specimens were taken from girth welds in API 5LX70 pipe of 1219 mm (48 inches) in diameter by 8,0 mm (0,323 inch) and 13,3 mm (0,524 inch) wall. The test welds were made with the SMAW (8 welds) and GMAW (9 welds) welding processes. Upon completion of the non-destructive tests, 96 curved wide plate specimens were tested to destruction under tensile load. Testing was performed at low temperaturemore » (-50{degrees}C/-58{degrees}F). Defect type, defect position and size were determined from photographs of the fracture face and macro sections (defect characterisation and sizing). In total, 290 typical surface breaking and embedded defects in SMAW or GMAW girth welds have been evaluated. The vast majority of these defects were grossly out of tolerance with respect to current weld quality (workmanship) acceptance levels. To allow the defect tolerance to be determined, the failure strains and stresses were correlated with a defect length determined for an equivalent 3 mm (0, 118 inch) deep defect. This target depth was chosen to represent the average height of one weld pass. The results of this approach have been compared to wall thickness, current workmanship and the EPRG Tier 2 defect limit for planar defects. The defect lengths were derived for rectangular, parabolic and elliptical defect representations.« less

Strength and Microstructure of Ceramics.

DTIC Science & Technology

1987-11-01

triangular slab. 12-mm edge length and 2-mm thickness. to produce crack 7 mm long. Starter notch length portantly. the strength plateau at small flaw sizes...however. a tapered the starter notch tip. "Pop-in" behavior of this kind is not uncom- geometry was used. width increasing in the direction of ultimate...mon in notched specimens, of course: in such cases the initial crack propagation. The main crack was started at a sawcut notch fracture response can be

The role of axial length-corneal radius of curvature ratio in refractive state categorization in a nigerian population.

PubMed

Iyamu, Eghosasere; Iyamu, Joy; Obiakor, Christian Izuchukwu

2011-01-01

The aim of this study was to investigate the association of axial length (AL)/corneal radius of curvature (CRC) ratio (AL/CRC) with spherical equivalent refractive state (SER) in young adults. A total of seventy (n = 70) subjects consisting of 31 males and 39 females participated in this study. Subjects were categorized into emmetropia, hyperopia and myopia using the spherical equivalent refraction. The axial length was measured with I-2100 A-Scan ultrasonography/Biometer (CIMA Technology, USA), the corneal radius of curvature with Bausch & Lomb H-135A (Bausch & Lomb Corp., USA), and the refractive state by static retinoscopy and subjective refraction. The mean AL, CRC and AL/CRC ratio of all subjects were 23.74 ± 0.70 mm, 7.84 ± 0.19 mm, and 3.03 ± 0.14, respectively. Myopes had significantly longer AL, steeper CRC and higher AL/CRC ratio than the emmetropes and hyperopes. There was statistically significant inverse correlation between AL and CRC (r = -0.53, P < 0.0001), SER (r = -0.64, P < 0.0001), and between SER and AL/CRC (r = -0.78, P < 0.0001). A significant positive correlation was found between CRC and SER (r = -0.69, P < 0.0001). The categorization of the refractive state of an individual is better done by using the AL/CRC ratio index.

The bundling of actin with polyethylene glycol 8000 in the presence and absence of gelsolin.

PubMed Central

Goverman, J; Schick, L A; Newman, J

1996-01-01

Actin filament and bundle formation occur in the cytosol under conditions of very high total macromolecular concentration. In this study we have utilized the inert molecule polyethylene glycol 8000 (PEG) as a means of simulating crowded conditions in vitro. Column-purified Ca-actin was polymerized in the absence and presence of gelsolin (to regulate mean filament lengths between 50 and 5000 mers) and PEG (2-8%) using various concentrations of KCl and/or 2 mM divalent cations. Bundling was characterized by the scattered light intensity and mean diffusion coefficients obtained from dynamic light scattering, as well as by fluorescence and phase-contrast microscopy. The minimum concentration of KCl required for bundling decreases both with increasing concentration of PEG at a fixed mean filament length, and with decreasing filament length at a fixed concentration of PEG. In the absence of divalent cation, bundling is reversible on dilution, as determined by intensity levels, diffusion coefficients, and microscopy. However, with either 2 mM Mg2+ or Ca2+ added, bundling is irreversible under conditions of higher PEG concentrations or longer filaments, indicating that osmotic pressure effects cannot fully explain actin bundling with PEG. Weaker divalent cation-binding sites on actin as well as disulfide bonds appear to be involved in the irreversible bundling. Images FIGURE 7 PMID:8874022

Dual-slot antennas for microwave tissue heating: Parametric design analysis and experimental validation

PubMed Central

Brace, Christopher L.

2011-01-01

Purpose: Design and validate an efficient dual-slot coaxial microwave ablation antenna that produces an approximately spherical heating pattern to match the shape of most abdominal and pulmonary tumor targets.Methods: A dual-slot antenna geometry was utilized for this study. Permutations of the antenna geometry using proximal and distal slot widths from 1 to 10 mm separated by 1–20 mm were analyzed using finite-element electromagnetic simulations. From this series, the most optimal antenna geometry was selected using a two-term sigmoidal objective function to minimize antenna reflection coefficient and maximize the diameter-to-length aspect ratio of heat generation. Sensitivities to variations in tissue properties and insertion depth were also evaluated in numerical models. The most optimal dual-slot geometry of the parametric analysis was then fabricated from semirigid coaxial cable. Antenna reflection coefficients at various insertion depths were recorded in ex vivo bovine livers and compared to numerical results. Ablation zones were then created by applying 50 W for 2–10 min in simulations and ex vivo livers. Mean zone diameter, length, aspect ratio, and reflection coefficients before and after heating were then compared to a conventional monopole antenna using ANOVA with post-hoc t-tests. Statistical significance was indicated for P < 0.05.Results: Antenna performance was highly sensitive to dual-slot geometry. The best-performing designs utilized a proximal slot width of 1 mm, distal slot width of 4 mm ± 1 mm and separation of 8 mm ± 1 mm. These designs were characterized by an active choking mechanism that focused heating to the distal tip of the antenna. A dual-band resonance was observed in the most optimal design, with a minimum reflection coefficient of −20.9 dB at 2.45 and 1.25 GHz. Total operating bandwidth was greater than 1 GHz, but the desired heating pattern was achieved only near 2.45 GHz. As a result, antenna performance was robust to changes in insertion depth and variations in relative permittivity of the surrounding tissue medium. In both simulations and ex vivo liver, the dual-slot antenna created ablations greater in diameter than a coaxial monopole (35 mm ± 2 mm versus 31 mm ± 2 mm; P < 0.05), while also shorter in length (49 mm ± 2 mm versus 60 mm ± 6 mm; P < 0.001) after 10 min. Similar results were obtained after 2 and 5 min as well.Conclusions: Dual-slot antennas can produce more spherical ablation zones while retaining low reflection coefficients. These benefits are obtained without adding to the antenna diameter. Further evaluation for clinical microwave ablation appears warranted. PMID:21859025

Fragmentation-based QM/MM simulations: length dependence of chain dynamics and hydrogen bonding of polyethylene oxide and polyethylene in aqueous solutions.

PubMed

Li, Hui; Li, Wei; Li, Shuhua; Ma, Jing

2008-06-12

Molecular fragmentation quantum mechanics (QM) calculations have been combined with molecular mechanics (MM) to construct the fragmentation QM/MM method for simulations of dilute solutions of macromolecules. We adopt the electrostatics embedding QM/MM model, where the low-cost generalized energy-based fragmentation calculations are employed for the QM part. Conformation energy calculations, geometry optimizations, and Born-Oppenheimer molecular dynamics simulations of poly(ethylene oxide), PEO(n) (n = 6-20), and polyethylene, PE(n) ( n = 9-30), in aqueous solution have been performed within the framework of both fragmentation and conventional QM/MM methods. The intermolecular hydrogen bonding and chain configurations obtained from the fragmentation QM/MM simulations are consistent with the conventional QM/MM method. The length dependence of chain conformations and dynamics of PEO and PE oligomers in aqueous solutions is also investigated through the fragmentation QM/MM molecular dynamics simulations.

Sex Determination of Carolina Wrens (Thryothorus ludovicianus) in the Mississippi Alluvial Valley

USGS Publications Warehouse

Twedt, D.J.

2004-01-01

I identified sexual dimorphism in wing length (unflattened chord) of Carolina Wrens (Thryothorus ludovicianus) within the central Mississippi Alluvial Valley (northeast Louisiana and west-central Mississippi) and used this difference to assign a sex to captured wrens. Wrens were identified as female when wing length was less than 57.5 mm or male when wing length was greater than 58.5 mm. Verification of predicted sex was obtained from recaptures of banded individuals where sex was ascertained from the presence of a cloacal protuberance or brood patch. Correct prediction of sex was 81% for adult females and 95% for adult males. An alternative model, which categorized wrens with wing lengths of 58 and 59 mm as birds of unknown sex, increased correct prediction of females to 93% but reduced the number of individuals to which sex was assigned. These simple, predictive, wing-length-based models also correctly assigned sex for more than 88% of young (hatching-year) birds.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Q. G.; Chen, N.; Zhang, M.

Five IDs will be built for the Shanghai Synchrotron Radiation Facility (SSRF). Two identical mini-gap undulators with the period length 25mm and the minimum gap 6mm will use the in-vacuum technology and can operate in tapered mode. Two wigglers with the period lengths 7.9cm and 14cm and the same minimum gap 14mm will produce the peak fields of 1.2T and 1.94T. A variable polarization undulator of the APPLE-II type with 4.2m long and the period length 10cm can provide linearly, circularly and elliptically polarized radiation in a wide spectral range. This paper describes the magnet designs and the mechanical structuremore » designs of these IDs.« less

Effect of the specimen length on ultrasonic P-wave velocity in some volcanic rocks and limestones

NASA Astrophysics Data System (ADS)

Karaman, Kadir; Kaya, Ayberk; Kesimal, Ayhan

2015-12-01

Ultrasonic P-wave velocity (UPV) is commonly used in different fields such as civil, mining, geotechnical, and rock engineering. One of the significant parameters which affect the UPV of rock materials is likely to be the length of test cores although it is not mentioned in the literature. In this study, in order to explore the influence of the specimen length on the UPV, rock samples were collected from eight different locations in Turkey. The NX-sized core specimens having different length of 50, 75, 100, 125, and 150 mm were prepared. Before the analyses, rocks were divided into two groups in terms of their geological origins such as volcanic and chemical sedimentary (limestone) rocks. The UPV tests were carried out under dry and saturated conditions for each 200 core specimens. By evaluating the test results, it was shown that the length of the specimens significantly affects the UPV values. Based on the regression analyses, a method was developed to determine the threshold specimen length of studied rocks. Fluctuations in UPVdry and UPVsat values were generally observed for cores smaller than the threshold specimen length. In this study, the threshold specimen length was determined as 79 mm for volcanic rocks and 109 mm for limestones.

Sex Difference in the Morphology of Pineal Gland in Adults Based on Brain Magnetic Resonance Imaging.

PubMed

Han, Qing; Li, Youqiong; Wang, Jincheng; Zhao, Xue

2018-03-30

We aimed to figure out the anatomical features of pineal gland region on magnetic resonance imaging (MRI) and to explore the sex difference in pineal gland-related parameters with increasing age. We measured the pineal gland on MRI images from 198 healthy adults (96 males and 102 females). Included subjects were divided into 4 age groups. After 3-dimensional reconstruction, the anatomic features of pineal gland and its distances to superior colliculus and splenium of corpus callosum were analyzed in each group. The prevalence of cystic pineal gland was calculated. Moreover, we calculated the volume of pineal gland (PGV) and explored the differences of PGV in males and females across different age groups. Linear regression analysis was performed to detect the relationship between age and pineal gland-related parameters. In 198 subjects, the mean length, width, and height of pineal gland were 7.58 ± 0.45 mm, 4.92 ± 0.40 mm, and 2.90 ± 0.20 mm. The distances between pineal gland and superior colliculus as well as splenium of corpus callosum were 3.96 ± 0.92 mm and 4.3 ± 1.89 mm, respectively. The PGV was 54.1 ± 7.02 mm. Significant sex differences were found in pineal gland length (P < 0.001), cranial cavity diameter (P < 0.001), pineal gland index (P < 0.001) and PGV values (P = 0.02). The prevalence of cystic pineal gland was 36.4% in total subjects, 41.7% in males and 32.4% in females. No linear relationship was found between age and pineal gland parameters. We measured the pineal gland morphology based on MRI images. Significant influences on pineal gland parameters were found in subjects with different sex, whereas no effect was observed from age.

The influence of the choice of closing wedge angle on leg length discrepancy after proximal femoral varus osteotomy.

PubMed

Segaren, N; Abdul-Jabar, H B; Hashemi-Nejad, A

2014-08-01

Proximal femoral varus osteotomy improves the biomechanics of the hip and can stimulate normal acetabular development in a dysplastic hip. Medial closing wedge osteotomy remains the most popular technique, but is associated with shortening of the ipsilateral femur. We produced a trigonometric formula which may be used pre-operatively to predict the resultant leg length discrepancy (LLD). We retrospectively examined the influence of the choice of angle in a closing wedge femoral osteotomy on LLD in 120 patients (135 osteotomies, 53% male, mean age six years, (3 to 21), 96% caucasian) over a 15-year period (1998 to 2013). A total of 16 of these patients were excluded due to under or over varus correction. The patients were divided into three age groups: paediatric (< 10 years), adolescent (10 to 16 years) and adult (> 16 years). When using the same saw blades as in this series, the results indicated that for each 10° of angle of resection the resultant LLD equates approximately to multiples of 4 mm, 8 mm and 12 mm in the three age groups, respectively. Statistical testing of the 59 patients who had a complete set of pre- and post-operative standing long leg radiographs, revealed a Pearson's correlation coefficient for predicted versus radiologically observed shortening when using a wedge of either 10° or 20° of 0.93 (p < 0.001). The 95% limits of agreement from the Bland-Altman analysis for this subgroup were -3.5 mm to +3.3 mm. It has been accepted that a 10 mm discrepancy is clinically acceptable. This study identified a geometric model that provided satisfactory accuracy when using specific saw blades of known thicknesses for this formula to be used in clinical practice. ©2014 The British Editorial Society of Bone & Joint Surgery.

Preoperative CT planning of screw length in arthroscopic Latarjet.

PubMed

Hardy, Alexandre; Gerometta, Antoine; Granger, Benjamin; Massein, Audrey; Casabianca, Laurent; Pascal-Moussellard, Hugues; Loriaut, Philippe

2018-01-01

The Latarjet procedure has shown its efficiency for the treatment of anterior shoulder dislocation. The success of this technique depends on the correct positioning and fusion of the bone block. The length of the screws that fix the bone block can be a problem. They can increase the risk of non-union if too short or be the cause of nerve lesion or soft tissue discomfort if too long. Suprascapular nerve injuries have been reported during shoulder stabilisation surgery up to 6 % of the case. Bone block non-union depending on the series is found around 20 % of the cases. The purpose of this study was to evaluate the efficiency of this CT preoperative planning to predict optimal screws length. The clinical importance of this study lies in the observation that it is the first study to evaluate the efficiency of CT planning to predict screw length. Inclusion criteria were patients with chronic anterior instability of the shoulder with an ISIS superior to 4. Exclusion criteria were patients with multidirectional instability or any previous surgery on this shoulder. Thirty patients were included prospectively, 11 of them went threw a CT planning, before their arthroscopic Latarjet. Optimal length of both screws was calculated, adding the size of the coracoid at 5 and 15 mm from the tip to the glenoid. Thirty-two-mm screws were used for patients without planning. On a post-operative CT scan with 3D reconstruction, the distance between the screw tip and the posterior cortex was measured. A one-sample Wilcoxon test was used to compare the distance from the tip of the screw to an acceptable positioning of ±2 mm from the posterior cortex. In the group without planning, screw 1 tended to differ from the acceptable positioning: mean 3.44 mm ± 3.13, med 2.9 mm, q1; q3 [0.6; 4.75] p = 0.1118, and screw 2 differed significantly from the acceptable position: mean 4.83 mm ± 4.11, med 3.7 mm, q1; q3 [1.7; 5.45] p = 0.0045. In the group with planning, position of screw 1 or 2 showed no significant difference from the acceptable position: mean 2.45 mm ± 2.07 med 1.8 mm, q1; q3 [1; 3.3] p = 1; mean 2.75 mm ± 2.32 med 2.3 mm, q1; q3 [1.25; 3.8] p = 0.5631. Unplanned Latarjet can lead to inaccurate screw length especially in the lower screw and can increase the risk of non-union and nerve damage. The clinical relevance of this article is that CT planning of screw length before surgery showed good results on post-operative CT.

Influence of the posterior tibial slope on the flexion gap in total knee arthroplasty.

PubMed

Okazaki, Ken; Tashiro, Yasutaka; Mizu-uchi, Hideki; Hamai, Satoshi; Doi, Toshio; Iwamoto, Yukihide

2014-08-01

Adjusting the joint gap length to be equal in both extension and flexion is an important issue in total knee arthroplasty (TKA). It is generally acknowledged that posterior tibial slope affects the flexion gap; however, the extent to which changes in the tibial slope angle directly affect the flexion gap remains unclear. This study aimed to clarify the influence of tibial slope changes on the flexion gap in cruciate-retaining (CR) or posterior-stabilizing (PS) TKA. The flexion gap was measured using a tensor device with the femoral trial component in 20 cases each of CR- and PS-TKA. A wedge plate with a 5° inclination was placed on the tibial cut surface by switching its front-back direction to increase or decrease the tibial slope by 5°. The flexion gap after changing the tibial slope was compared to that of the neutral slope measured with a flat plate that had the same thickness as that of the wedge plate center. When the tibial slope decreased or increased by 5°, the flexion gap decreased or increased by 1.9 ± 0.6mm or 1.8 ± 0.4mm, respectively, with CR-TKA and 1.2 ± 0.4mm or 1.1 ± 0.3mm, respectively, with PS-TKA. The influence of changing the tibial slope by 5° on the flexion gap was approximately 2mm with CR-TKA and 1mm with PS-TKA. This information is useful when considering the effect of manipulating the tibial slope on the flexion gap when performing CR- or PS-TKA. Copyright © 2014 Elsevier B.V. All rights reserved.

Experimental Study on Full-Scale Beams Made by Reinforced Alkali Activated Concrete Undergoing Flexure.

PubMed

Monfardini, Linda; Minelli, Fausto

2016-08-30

Alkali Activated Concrete (AAC) is an alternative kind of concrete that uses fly ash as a total replacement of Portland cement. Fly ash combined with alkaline solution and cured at high temperature reacts to form a binder. Four point bending tests on two full scale beams made with AAC are described in this paper. Companion small material specimens were also casted with the aim of properly characterizing this new tailored material. The beam's length was 5000 mm and the cross section was 200 mm × 300 mm. The AAC consisted of fly ash, water, sand 0-4 mm and coarse aggregate 6-10 mm; and the alkaline solution consisted of sodium hydroxide mixed with sodium silicate. No cement was utilized. The maximum aggregate size was 10 mm; fly ash was type F, containing a maximum calcium content of 2%. After a rest period of two days, the beam was cured at 60 °C for 24 h. Data collected and critically discussed included beam deflection, crack patterns, compressive and flexural strength and elastic modulus. Results show how AAC behavior is comparable with Ordinary Portland Cement (OPC) based materials. Nonlinear numerical analyses are finally reported, promoting a better understanding of the structural response.

Experimental Study on Full-Scale Beams Made by Reinforced Alkali Activated Concrete Undergoing Flexure

PubMed Central

Monfardini, Linda; Minelli, Fausto

2016-01-01

Alkali Activated Concrete (AAC) is an alternative kind of concrete that uses fly ash as a total replacement of Portland cement. Fly ash combined with alkaline solution and cured at high temperature reacts to form a binder. Four point bending tests on two full scale beams made with AAC are described in this paper. Companion small material specimens were also casted with the aim of properly characterizing this new tailored material. The beam’s length was 5000 mm and the cross section was 200 mm × 300 mm. The AAC consisted of fly ash, water, sand 0–4 mm and coarse aggregate 6–10 mm; and the alkaline solution consisted of sodium hydroxide mixed with sodium silicate. No cement was utilized. The maximum aggregate size was 10 mm; fly ash was type F, containing a maximum calcium content of 2%. After a rest period of two days, the beam was cured at 60 °C for 24 h. Data collected and critically discussed included beam deflection, crack patterns, compressive and flexural strength and elastic modulus. Results show how AAC behavior is comparable with Ordinary Portland Cement (OPC) based materials. Nonlinear numerical analyses are finally reported, promoting a better understanding of the structural response. PMID:28773861

Study on the Connecting Length of CFRP

NASA Astrophysics Data System (ADS)

Liu, Xiongfei; Li, Yue; Li, Zhanguo

2018-05-01

The paper studied the varying mode of shear stress in the connecting zone of CFRP. Using epoxy resin (EP) as bond material, performance of specimens with different connecting length of CFRP was tested to obtain the conclusion. CFRP-confined concrete column was tested subsequently to verify the conclusion. The results show that: (1) The binding properties of modified epoxy resin with CFRP is good; (2) As the connecting length increased, the ultimate tensile strength of CFRP increased as well in the range of the experiment parameters; (3) Tensile strength of CFRP can reach the ultimate strength when the connecting length is 90mm;(4) The connecting length of 90mm of CFRP meet the reinforcement requirements.

Anatomical dimensions of trachea, main bronchi, subcarinal and bronchial angles in fetuses measured ex vivo.

PubMed

Harjeet; Sahni, Daisy; Batra, Yatindra Kumar; Rajeev, Subramanyam

2008-11-01

The increasing opportunities to consider fetal intervention in selected cases of life-threatening malformations have necessitated airway management of fetuses with low gestational age. This study is aimed to determine the anatomical dimensions of trachea, main bronchi, subcarinal and bronchial angles and their correlation to age and crown rump length (CRL) in fetuses. Measurements of tracheo-bronchial dimensions including the subcarinal and bronchial angles with the vertical were taken in specimens obtained from 40 fetuses, varying in CRL from 61 to 270 mm. The incidence of different shapes at the upper end of trachea was studied. The subcarinal and angles of main bronchi with the vertical were measured radiographically with 20% barium sulfate, in another group of 21 fetuses varying in CRL from 63 to 129 mm. Forty fetuses (22 males, 18 females) were analyzed for the dimensions based on CRL (61-130 mm; 131-200 mm; 201-270 mm--CRL 1, 2, and 3 respectively). The internal transverse diameter of trachea was found to increase steadily from 1.87 +/- 0.56 to 2.67 +/- 0.7 mm (P < 0.001) and 3.68 +/- 0.39 mm (P < 0.001) with increasing CRL. Similarly the outer transverse and antero-posterior diameter of the trachea increased steadily with age. Tracheal length was found to increase significantly to 17.48 +/- 2.89 mm and 24.17 +/- 2.3 from 12.72 +/- 2.5 mm (P < 0.001). The length of paries membranaceous increased with gestational age. Although the length of bronchi increased significantly and linearly, subcarinal and bronchial angles did not show any significant changes with age. There was no sexual dimorphism in measurements in the fetuses of corresponding CRL. Oval shaped trachea was found in 60% and circular in 40% of fetuses. The measurements of subcarinal and bronchial angles performed by radiology were almost the same as those measured in trachea separated from fetuses. The internal transverse, outer transverse and antero-posterior diameters, length of trachea and bronchi and circumference of trachea, relate in a linear fashion to CRL and age. However, subcarinal and bronchial angles remained constant.

[Effects of salt stress on germination and in vitro growth of pistachio (Pistacia vera L.)].

PubMed

Benmahioul, Benamar; Daguin, Florence; Kaid-Harche, Meriem

2009-08-01

In order to study the salinity tolerance of pistachio (Pistacia vera L.), embryos developed from mature seeds were isolated and cultured in vitro and subjected to different NaCl concentrations (0, 42.8, 85.5, 171.1 and 256.6 mM) for 30 days. The results showed that in vitro germination of embryonic axes was not affected by the salt concentration. However, the germinated embryo survival rates decreased from 100% for the control to 62.9% for the highest salt concentration (256.6 mM). In addition, the plantlet growth (length of aerial and root parts, number of leaf produced per embryo, as well as the production of total fresh and dry matter for both aerial parts and roots) showed significant differences according the various salt concentrations.

Radio tag retention and tag-related mortality among adult sockeye salmon

USGS Publications Warehouse

Ramstad, Kristina M.; Woody, Carol Ann

2003-01-01

Tag retention and tag-related mortality are concerns for any tagging study but are rarely estimated. We assessed retention and mortality rates for esophageal radio tag implants in adult sockeye salmon Oncorhynchus nerka. Migrating sockeye salmon captured at the outlet of Lake Clark, Alaska, were implanted with one of four different radio tags (14.5 × 43 mm (diameter × length), 14.5 × 49 mm, 16 × 46 mm, and 19 × 51 mm). Fish were observed for 15 to 35 d after tagging to determine retention and mortality rates. The overall tag retention rate was high (0.98; 95% confidence interval (CI), 0.92-1.00; minimum, 33 d), with one loss of a 19-mm × 51- mm tag. Mortality of tagged sockeye salmon (0.02; 95% CI, 0-0.08) was similar to that of untagged controls (0.03 (0-0.15)). Sockeye salmon with body lengths (mid-eye to tail fork) of 585-649 mm retained tags as large as 19 × 51 mm and those with body lengths of 499-628 mm retained tags as small as 14.5 × 43 mm for a minimum of 33 d with no increase in mortality. The tags used in this study represent a suite of radio tags that vary in size, operational life, and cost but that are effective in tracking adult anadromous salmon with little tag loss or increase in fish mortality.

Nutrient bioassimilation capacity of aquacultured oysters: quantification of an ecosystem service.

PubMed

Higgins, Colleen B; Stephenson, Kurt; Brown, Bonnie L

2011-01-01

Like many coastal zones and estuaries, the Chesapeake Bay has been severely degraded by cultural eutrophication. Rising implementation costs and difficulty achieving nutrient reduction goals associated with point and nonpoint sources suggests that approaches supplemental to source reductions may prove useful in the future. Enhanced oyster aquaculture has been suggested as one potential policy initiative to help rid the Bay waters of excess nutrients via harvest of bioassimilated nutrients. To assess this potential, total nitrogen (TN), total phosphorous (TP), and total carbon (TC) content were measured in oyster tissue and shell at two floating-raft cultivation sites in the Chesapeake Bay. Models were developed based on the common market measurement of total length (TL) for aquacultured oysters, which was strongly correlated to the TN (R2 = 0.76), TP (R2 = 0.78), and TC (R2 = 0.76) content per oyster tissue and shell. These models provide resource managers with a tool to quantify net nutrient removal. Based on model estimates, 10(6) harvest-sized oysters (76 mm TL) remove 132 kg TN, 19 kg TP, and 3823 kg TC. In terms of nutrients removed per unit area, oyster harvest is an effective means of nutrient removal compared with other nonpoint source reduction strategies. At a density of 286 oysters m(-2), assuming no mortality, harvest size nutrient removal rates can be as high as 378 kg TN ha(-1), 54 kg TP ha(-1), and 10,934 kg TC ha(-1) for 76-mm oysters. Removing 1 t N from the Bay would require harvesting 7.7 million 76-mm TL cultivated oysters.

Three-dimensional architecture of the whole human soleus muscle in vivo

PubMed Central

Finni, Taija; D’Souza, Arkiev; Eguchi, Junya; Clarke, Elizabeth C.; Herbert, Robert D.

2018-01-01

Background Most data on the architecture of the human soleus muscle have been obtained from cadaveric dissection or two-dimensional ultrasound imaging. We present the first comprehensive, quantitative study on the three-dimensional anatomy of the human soleus muscle in vivo using diffusion tensor imaging (DTI) techniques. Methods We report three-dimensional fascicle lengths, pennation angles, fascicle curvatures, physiological cross-sectional areas and volumes in four compartments of the soleus at ankle joint angles of 69 ± 12° (plantarflexion, short muscle length; average ± SD across subjects) and 108 ± 7° (dorsiflexion, long muscle length) of six healthy young adults. Microdissection and three-dimensional digitisation on two cadaveric muscles corroborated the compartmentalised structure of the soleus, and confirmed the validity of DTI-based muscle fascicle reconstructions. Results The posterior compartments of the soleus comprised 80 ± 5% of the total muscle volume (356 ± 58 cm3). At the short muscle length, the average fascicle length, pennation angle and curvature was 37 ± 8 mm, 31 ± 3° and 17 ± 4 /m, respectively. We did not find differences in fascicle lengths between compartments. However, pennation angles were on average 12° larger (p < 0.01) in the posterior compartments than in the anterior compartments. For every centimetre that the muscle-tendon unit lengthened, fascicle lengths increased by 3.7 ± 0.8 mm, pennation angles decreased by −3.2 ± 0.9° and curvatures decreased by −2.7 ± 0.8 /m. Fascicles in the posterior compartments rotated almost twice as much as in the anterior compartments during passive lengthening. Discussion The homogeneity in fascicle lengths and inhomogeneity in pennation angles of the soleus may indicate a functionally different role for the anterior and posterior compartments. The data and techniques presented here demonstrate how DTI can be used to obtain detailed, quantitative measurements of the anatomy of complex skeletal muscles in living humans. PMID:29682414

Relationship between fish size and upper thermal tolerance

USGS Publications Warehouse

Recsetar, Matthew S.; Zeigler, Matthew P.; Ward, David L.; Bonar, Scott A.; Caldwell, Colleen A.

2012-01-01

Using critical thermal maximum (CTMax) tests, we examined the relationship between upper temperature tolerances and fish size (fry-adult or subadult lengths) of rainbow trout Oncorhynchus mykiss (41-200-mm TL), Apache trout O. gilae apache (40-220-mm TL), largemouth bass Micropterus salmoides (72-266-mm TL), Nile tilapia Oreochromis niloticus (35-206-mm TL), channel catfish Ictalurus punctatus (62-264 mm-TL), and Rio Grande cutthroat trout O. clarkii virginalis (36-181-mm TL). Rainbow trout and Apache trout were acclimated at 18°C, Rio Grande cutthroat trout were acclimated at 14°C, and Nile tilapia, largemouth bass, and channel catfish were acclimated at 25°C, all for 14 d. Critical thermal maximum temperatures were estimated and data were analyzed using simple linear regression. There was no significant relationship (P > 0.05) between thermal tolerance and length for Nile tilapia (P = 0.33), channel catfish (P = 0.55), rainbow trout (P = 0.76), or largemouth bass (P = 0.93) for the length ranges we tested. There was a significant negative relationship between thermal tolerance and length for Rio Grande cutthroat trout (R2 = 0.412, P 2 = 0.1374, P = 0.028); however, the difference was less than 1°C across all lengths of Apache trout tested and about 1.3°C across all lengths of Rio Grande cutthroat trout tested. Because there was either no or at most a slight relationship between upper thermal tolerance and size, management and research decisions based on upper thermal tolerance should be similar for the range of sizes within each species we tested. However, the different sizes we tested only encompassed life stages ranging from fry to adult/subadult, so thermal tolerance of eggs, alevins, and larger adults should also be considered before making management decisions affecting an entire species.

Refractive Index Sensing with D-Shaped Plastic Optical Fibers for Chemical and Biochemical Applications

PubMed Central

Sequeira, Filipa; Duarte, Daniel; Bilro, Lúcia; Rudnitskaya, Alisa; Pesavento, Maria; Zeni, Luigi; Cennamo, Nunzio

2016-01-01

We report the optimization of the length of a D-shaped plastic optical fiber (POF) sensor for refractive index (RI) sensing from a numerical and experimental point of view. The sensing principle is based on total internal reflection (TIR). POFs with 1 mm in diameter were embedded in grooves, realized in planar supports with different lengths, and polished to remove the cladding and part of the core. All D-shaped POF sensors were tested using aqueous medium with different refractive indices (from 1.332 to 1.471) through intensity-based configuration. Results showed two different responses. Considering the refractive index (RI) range (1.33–1.39), the sensitivity and the resolution of the sensor were strongly dependent on the sensing region length. The highest sensitivity (resolution of 6.48 × 10−3 refractive index units, RIU) was obtained with 6 cm sensing length. In the RI range (1.41–1.47), the length of the sensing region was not a critical aspect to obtain the best resolution. These results enable the application of this optical platform for chemical and biochemical evanescent field sensing. The sensor production procedure is very simple, fast, and low-cost. PMID:27983608

Prey vulnerability to peacock cichlids and largemouth bass based on predator gape and prey body depth

USGS Publications Warehouse

Hill, Jeffrey E.; Nico, Leo G.; Cichra, Charles E.; Gilbert, Carter R.

2005-01-01

The interaction of prey fish body depth and predator gape size may produce prey assemblages dominated by invulnerable prey and excessive prey-to-predator biomass ratios. Peacock cichlids (Cichla ocellaris) were stocked into southeast Florida canals to consume excess prey fish biomass, particularly spotted tilapia (Tilapia mariae). The ecomorphologically similar largemouth bass (Micropterus salmoides) was already present in the canals. We present relations of length-specific gape size for peacock cichlids and largemouth bass. Both predators have broadly overlapping gape size, but largemouth bass ?126 mm total length have slightly larger gape sizes than peacock cichlids of the same length. Also, we experimentally tested the predictions of maximum prey size for peacock cichlids and determined that a simple method of measuring gape size used for largemouth bass also is appropriate for peacock cichlids. Lastly, we determined relations of body depth and length of prey species to investigate relative vulnerability. Using a simple predator-prey model and length frequencies of predators and bluegill (Lepomis macrochirus), redear sunfish (Lepomis microlophus), and spotted tilapia prey, we documented that much of the prey biomass in southeast Florida canals is unavailable for largemouth bass and peacock cichlid predation.

Refractive Index Sensing with D-Shaped Plastic Optical Fibers for Chemical and Biochemical Applications.

PubMed

Sequeira, Filipa; Duarte, Daniel; Bilro, Lúcia; Rudnitskaya, Alisa; Pesavento, Maria; Zeni, Luigi; Cennamo, Nunzio

2016-12-13

We report the optimization of the length of a D-shaped plastic optical fiber (POF) sensor for refractive index (RI) sensing from a numerical and experimental point of view. The sensing principle is based on total internal reflection (TIR). POFs with 1 mm in diameter were embedded in grooves, realized in planar supports with different lengths, and polished to remove the cladding and part of the core. All D-shaped POF sensors were tested using aqueous medium with different refractive indices (from 1.332 to 1.471) through intensity-based configuration. Results showed two different responses. Considering the refractive index (RI) range (1.33-1.39), the sensitivity and the resolution of the sensor were strongly dependent on the sensing region length. The highest sensitivity (resolution of 6.48 × 10 -3 refractive index units, RIU) was obtained with 6 cm sensing length. In the RI range (1.41-1.47), the length of the sensing region was not a critical aspect to obtain the best resolution. These results enable the application of this optical platform for chemical and biochemical evanescent field sensing. The sensor production procedure is very simple, fast, and low-cost.

The efficacy of short (6 mm) dental implants with a novel thread design.

PubMed

Bechara, Soheil; Nimčenko, Tatjana; Kubilius, Ričardas

2017-01-01

To assess efficacy of short (6 mm) implants with a novel macrostructure and thread design placed in a compromised bone situations of edentulous posterior regions of maxilla (3-4 mm of bone height under sinus floor) as compared to results of clinical situations treated with simultaneous maxillary sinus grafting and placement of long (≥10 mm) implants of the same company. Clinical cases of conducted clinical study. Patients with compromised bone height in edentulous posterior regions of maxilla were randomly divided into two groups. Short (6mm length) implant treatment conducted in the test group and simultaneous sinus lift with standard length implant placement treatment in the control group. In general implant stability quotient (ISQ) and marginal bone level (MBL) changes values in both groups were comparable. However, significant negative correlation was found between implant's diameter and MBL changes. Implant's length has little if none impact on initial implant anchorage, especially in greatly compromised residual bone situations. Results have confirmed that implant initial stability mainly depends on implant's macro-design and further its development on implant's micro-design: namely, implant diameter rather than length, tapered shape and improved thread design determines primarily acquired mechanical anchorage, while bioactive surface treatment ensures development of biological stability.

Root canal penetration of a sodium hypochlorite mixture using sonic or ultrasonic activation.

PubMed

Sáinz-Pardo, Marta; Estevez, Roberto; Pablo, Óliver Valencia de; Rossi-Fedele, Giampiero; Cisneros, Rafael

2014-01-01

The purpose of this ex vivo study was to determine, in "open" and "closed" systems, whether the design has an influence on the penetration length of sodium hypochlorite mixed with a radiopaque contrast medium, measured in millimeters, when delivered using positive pressure (PP) and using sonic (SI) or passive ultrasonic (PUI) activation. Sixty single-rooted teeth were divided into two groups: open and closed systems (n=30). Root canal shaping was performed to a working length of 17 mm. The samples were divided into three sub-groups (n=10) according to irrigant delivery and activation: PP, and SI or PUI activation. By using radiographs, penetration length was measured, and vapor lock was assessed. For the closed group, the penetration distance means were: PP 15.715 (±0.898) mm, SI 16.299 (±0.738) mm and PUI 16.813 (±0.465) mm, with vapor lock occurring in 53.3% of the specimens. In the open group, penetration to 17 mm occurred in 97.6% of the samples, and no vapor lock occurred. Irrigant penetration and distribution evaluation using open and closed systems provide significantly different results. For closed systems, PUI is the most effective in delivering the irrigant to working length, followed by SI.

Physical and chemical characteristics of goldenberry fruit (Physalis peruviana L.).

PubMed

Yıldız, Gökçen; İzli, Nazmi; Ünal, Halil; Uylaşer, Vildan

2015-04-01

Some physical and chemical characteristics of goldenberry fruit (Physalis peruviana L.) were investigated. These characteristics are necessary for the design of equipments for harvesting, processing, transportation, sorting, separating and packing. The fruit length, diameter, geometric and arithmetic mean diameters, sphericity, surface area, projected areas (vertical-horizontal) and aspect ratio of goldenberries were determined as 17.52 mm, 17.31 mm, 17.33 mm, 17.38 mm, 98.9 %, 0.949 cm(2), 388.67-387.85 mm(2) and 0.988, respectively. The mass of fruit, bulk density, fruit density, porosity and fruit hardness were 3.091 g, 997.3 kg/m(3), 462.3 kg/m(3), 53.61 % and 8.01 N, respectively. The highest static coefficient of friction was observed on rubber surface, followed by stainless steel sheet, aluminum sheet, and plywood materials. The dry matter, water soluble dry matter, ash, protein, oil, carbohydrate, titratable acidity, pH, total sugar, reducing sugar, antioxidant capacity were 18.67 %, 14.17 %, 2.98 %, 1.66 %, 0.18 %, 13.86 %, 1.26 %, 6.07, 63.90 g/kg, 31.99 g/kg and 57.67 %, respectively. The fresh fruits have 145.22 mg gallic acid equivalent (GAE)/100 g total phenol content and skin colour data represented as L*, a*, b*, Chroma (C) and Hue angle (α) were 49.92, 25.11, 50.23, 56.12 and 63.48, respectively.

Virtual Surgical Planning for Correction of Delayed Presentation Scaphocephaly Using a Modified Melbourne Technique.

PubMed

Macmillan, Alexandra; Lopez, Joseph; Mundinger, Gerhard S; Major, Melanie; Medina, Miguel A; Dorafshar, Amir H

2018-02-23

Late treatment of scaphocephaly presents challenges including need for more complex surgery to achieve desired head shape. Virtual surgical planning for total vault reconstruction may mitigate some of these challenges, but has not been studied in this unique and complex clinical setting. A retrospective chart review was conducted for patients with scaphocephaly who presented to our institution between 2000 and 2014. Patients presenting aged 12 months or older who underwent virtual surgical planning-assisted cranial vault reconstruction were included. Patient demographic, intraoperative data, and postoperative outcomes were recorded. Pre- and postoperative anthropometric measurements were obtained to document the fronto-occipital (FO) and biparietal (BP) distance and calculate cephalic index (CI). Virtual surgical planning predicted, and actual postoperative anthropometric measurements were compared. Five patients were identified who fulfilled inclusion criteria. The mean age was 50.6 months. One patient demonstrated signs of elevated intracranial pressure preoperatively. Postoperatively, all but one needed no revisional surgery (Whitaker score of 1). No patient demonstrated postoperative evidence of bony defects, bossing, or suture restenosis. The mean preoperative, simulated, and actual postoperative FO length was 190.3, 182, and 184.3 mm, respectively. The mean preoperative, simulated, and actual postoperative BP length was 129, 130.7, and 131 mm, respectively. The mean preoperative, simulated, and actual postoperative CI was 66, 72, and 71.3, respectively. Based on our early experience, virtual surgical planning using a modified Melbourne technique for total vault remodeling achieves good results in the management of late presenting scaphocephaly.

The effect of repeated torque tightening on total lengths of implant abutments in different internal implant‒abutment connections.

PubMed

Saleh Saber, Fariba; Abolfazli, Nader; Jannatii Ataei, Soheil; Taghizade Motlagh, Mahsa; Gharekhani, Vahede

2017-01-01

Background. Since the misfit of crown has an important role in clinical performance of implant-supported prostheses, and due to the impact of the settling effect on misfit, the aim of this study was to investigate the impact of torque forces on the total lengths of narrow and short implant abutments in different internal implant‒abutment connections. Methods. In four different implant‒abutment connections, 8 analog implants with a normal diameter (4 mm) and narrow abutment (4.5 mm) were selected from groups of internal hex, internal octagon, morse hex 6° and morse hex 11°. Each of them was mounted within plaster type IV, and 32 samples were obtained. Then, the amount of vertical displacement was measured by closing the impression copings and applying torques of 20 25 and 30 Ncm. This stage was repeated for the abutment. In the next stage, the resin pattern was built and measurements were performed after applying the torques mentioned. Finally, after making the frame, this stage was repeated, and the settling effect was statistically analyzed with ANOVA. Results. In the stages of impression coping, resin pattern and final prosthesis, HEXAGONE had significantly the highest and OCTAGONE had the lowest rates of settling, and the settling of morse hex 11° and 6° was between them. Conclusion. Octagon implant had significantly the lowest settling in various clinical and laboratory stages by applying different torques.

The effect of repeated torque tightening on total lengths of implant abutments in different internal implant‒abutment connections

PubMed Central

Saleh Saber, Fariba; Abolfazli, Nader; Jannatii Ataei, Soheil; Taghizade Motlagh, Mahsa; Gharekhani, Vahede

2017-01-01

Background. Since the misfit of crown has an important role in clinical performance of implant-supported prostheses, and due to the impact of the settling effect on misfit, the aim of this study was to investigate the impact of torque forces on the total lengths of narrow and short implant abutments in different internal implant‒abutment connections. Methods. In four different implant‒abutment connections, 8 analog implants with a normal diameter (4 mm) and narrow abutment (4.5 mm) were selected from groups of internal hex, internal octagon, morse hex 6° and morse hex 11°. Each of them was mounted within plaster type IV, and 32 samples were obtained. Then, the amount of vertical displacement was measured by closing the impression copings and applying torques of 20 25 and 30 Ncm. This stage was repeated for the abutment. In the next stage, the resin pattern was built and measurements were performed after applying the torques mentioned. Finally, after making the frame, this stage was repeated, and the settling effect was statistically analyzed with ANOVA. Results. In the stages of impression coping, resin pattern and final prosthesis, HEXAGONE had significantly the highest and OCTAGONE had the lowest rates of settling, and the settling of morse hex 11° and 6° was between them. Conclusion. Octagon implant had significantly the lowest settling in various clinical and laboratory stages by applying different torques. PMID:28748052

Cementless total hip arthroplasty with a double chevron subtrochanteric shortening osteotomy in patients with Crowe type-IV hip dysplasia.

PubMed

Li, Xigong; Sun, Junying; Lin, Xiangjin; Xu, Sanzhong; Tang, Tiansi

2013-06-01

The authors describe a modified double chevron subtrochanteric shortening osteotomy combined with cementless total hip arthroplasty for Crowe type-IV hip dysplasia. Shortening the femur allows to relax the shortened musculature. This operation was performed in 18 patients (22 hips) between January 2000 and February 2006. The mean follow-up period was 5.6 years (range: 3 to 8 years). The mean amount of femoral subtrochanteric shortening was 38 mm (range: 25 to 60 mm). The mean Harris hip score improved from 47 (range: 35 to 65) preoperatively to 88 points (range: 75 to 97) at final follow-up. The Trendelenburg sign was corrected from positive to negative in 12 of 22 hips. No acetabular or femoral components loosened or required revision during the follow-up period. All osteotomy sites healed in 3 to 6 months without complications. Cementless total hip arthroplasty using the modified double chevron subtrochanteric osteotomy provided good short- to midterm results in all 22 Crowe type-IV hip dislocations. Moreover, it restored the anatomic hip center and the limb length, which contributed to correction of the preoperative limp.

Endoscopic sphincterotomy: follow-up evaluation of effects on the sphincter of Oddi.

PubMed

Geenen, J E; Toouli, J; Hogan, W J; Dodds, W J; Stewart, E T; Mavrelis, P; Riedel, D; Venu, R

1984-10-01

Endoscopic sphincterotomy (ES) alters the structure and motor function of the sphincter of Oddi (SO). The magnitude and duration of these changes, however, have not been critically examined. Before ES, 22 patients with common bile duct stones were evaluated by endoscopic retrograde cholangiography. The pressure gradient between the common bile duct and the duodenum, the SO basal pressure, and the SO peak phasic pressures were obtained. After ES, the electrosurgical incision length was determined using the extended papillotome and an inflated Fogarty balloon as reference. A high correlation existed between the endoscopist's estimate of ES incision size using this technique and the actual length of simulated incisions fashioned in cardboard mounts. These studies were repeated in all 22 patients at 1-yr follow-up and in 8 of these patients at 2-yr follow-up. At 12 mo and 24 mo after ES, the common bile duct (CBD) to duodenal pressure gradient and the sphincter of Oddi basal pressure were virtually eliminated. The amplitude of SO phasic contractions was significantly diminished 12 mo after ES (124 +/- 16 mmHg to 37 +/- 10 mmHg; p less than 0.001), but 24 mo after ES, SO phasic contraction amplitude was not significantly different from the values before ES. Incision length at 1-yr follow-up was reduced in the group of 22 patients from 11.6 +/- 0.8 mm to 8.3 +/- 0.5 mm (p less than 0.001), and in the group of 8 patients from 11.0 +/- 1.5 mm to 7.5 +/- 0.7 mm (p less than 0.025). After an additional 12 mo, however, i.e., 24 mo after ES, the incision length was 6.5 +/- 0.7 mm. There was no significant difference in incision length between the 12-mo and 24-mo examinations. We conclude that after ES, incision length decreases during the first year. There appears to be no further significant reduction in incision length at 2 yr. In addition, the reduction of the CBD to duodenal pressure gradient and the SO basal pressure remain unchanged for at least 2 yr. These manometric findings support the observation that after ES the enlarged opening of the CBD into the duodenum remains open for at least 2 yr.

Endorectal MR imaging of prostate cancer: Evaluation of tumor capsular contact length as a sign of extracapsular extension.

PubMed

Mendez, Gustavo; Foster, Bryan R; Li, Xin; Shannon, Jackilen; Garzotto, Mark; Amling, Christopher L; Coakley, Fergus V

2018-04-25

To evaluate the length of contact between dominant tumor foci and the prostatic capsule as a sign of extracapsular extension at endorectal multiparametric MR imaging. We retrospectively identified 101 patients over a three-year interval who underwent endorectal multiparametric prostate MR imaging prior to radical prostatectomy for prostate cancer. Two readers identified the presence of dominant tumor focus (largest lesion with PI-RADS version 2 score of 4 or 5), and measured the length of tumor capsular contact and likelihood of extracapsular extension by standard criteria (1-5 Likert scale). Results were analyzed using histopathological review as reference standard. Extracapsular extension was found at histopathological review in 27 patients. Reader 1 (2) identified dominant tumor in 79 (73) patients, with mean tumor capsular contact length of 18.2 (14.0) mm. The area under the receiver operating characteristic curve for identification of extracapsular extension by tumor capsular contact length was 0.76 for reader 1 and 0.77 for reader 2, with optimal discrimination at values of 18 mm and 21 mm, respectively. In the subset of patients without obvious extracapsular extension by standard criteria (Likert scores 1-3), corresponding values were 0.74 and 0.66 with optimal thresholds of 24 and 21 mm. Length of contact between the dominant tumor focus and the capsule is a moderately useful sign of extracapsular extension at endorectal multiparametric prostate MR imaging, including the subset of patients without obvious extracapsular extension by standard criteria, with optimal discrimination at threshold values of 18 to 24 mm. Copyright © 2018 Elsevier Inc. All rights reserved.

Effect of microneedles on transdermal permeation enhancement of amlodipine.

PubMed

Nalluri, Buchi N; Uppuluri, Chandrateja; Devineni, Jyothirmayee; Nayak, Atul; Nair, Karthik J; Whiteside, Benjamin R; Das, Diganta B

2017-06-01

The present study aimed to investigate the effect of microneedle (MN) geometry parameters like length, density, shape and type on transdermal permeation enhancement of amlodipine (AMLO). Two types of MN devices viz. AdminPatch® arrays (ADM) (0.6, 1.2 and 1.5 mm lengths) and laboratory-fabricated polymeric MNs (PM) of 0.6 mm length were employed. In the case of PMs, arrays were applied thrice at different places within a 1.77-cm 2 skin area (PM-3) to maintain the MN density closer to 0.6 mm ADM. Scaling analyses were done using dimensionless parameters like concentration of AMLO (C t /C s ), thickness (h/L) and surface area of the skin (Sa/L 2 ). Microinjection moulding technique was employed to fabricate PM. Histological studies revealed that the PM, owing to their geometry/design, formed wider and deeper microconduits when compared to ADM of similar length. Approximately 6.84- and 6.11-fold increase in the cumulative amount (48 h) of AMLO permeated was observed with 1.5 mm ADM and PM-3 treatments respectively, when compared to passive permeation amounts. Good correlations (R 2  > 0.89) were observed between different dimensionless parameters with scaling analyses. The enhancement in AMLO permeation was found to be in the order of 1.5 mm ADM ≥ PM-3 > 1.2 mm ADM > 0.6 mm ADM ≥PM-1 > passive. The study suggests that MN application enhances the AMLO transdermal permeation and the geometrical parameters of MNs play an important role in the degree of such enhancement.

Optical coherence tomography of the effects of stromal hydration on clear corneal incision architecture.

PubMed

Calladine, Daniel; Tanner, Vaughan

2009-08-01

To evaluate the effects of stromal hydration on clear corneal incision (CCI) architecture immediately after surgery using anterior segment optical coherence tomography (AS-OCT). Department of Ophthalmology, Royal Berkshire Hospital, Reading, United Kingdom. Clear corneal incisions in adult eyes were examined using a Visante AS-OCT imaging system within 1 hour of surgery. Half the CCIs had stromal hydration with a balanced salt solution and half did not. Incisions were made with a 2.75 mm steel keratome. Intraocular pressure (IOP) was measured within 90 minutes after surgery. The CCI length and corneal thickness at the CCI site were measured using software built into the AS-OCT system. Thirty CCIs were evaluated. Stromal hydration significantly increased the measured CCI length (P<.05, t test); this was the result of a trend toward increased corneal thickness at the CCI site with hydration (P<.1, t test). The mean CCI length was 1.69 mm +/- 0.27 (SD) (range 1.31 to 2.32 mm) with hydration and 1.51 +/- 0.23 mm (range 1.30 to 1.95 mm) without hydration. The mean IOP was 20.9 +/- 8.18 mm Hg and 15.8 +/- 8.20 mm Hg, respectively. The IOP tended to be higher with hydration (P<.1, t test). Local detachment of Descemet membrane was more likely with stromal hydration (63%) than without (25%). Stromal hydration significantly increased CCI length and tended to leave the eye with a higher early postoperative IOP, showing the importance of taking stromal hydration into account when designing similar OCT studies of CCI architecture.

Telescope-based cavity for negative ion beam neutralization in future fusion reactors.

PubMed

Fiorucci, Donatella; Hreibi, Ali; Chaibi, Walid

2018-03-01

In future fusion reactors, heating system efficiency is of the utmost importance. Photo-neutralization substantially increases the neutral beam injector (NBI) efficiency with respect to the foreseen system in the International Thermonuclear Experimental Reactor (ITER) based on a gaseous target. In this paper, we propose a telescope-based configuration to be used in the NBI photo-neutralizer cavity of the demonstration power plant (DEMO) project. This configuration greatly reduces the total length of the cavity, which likely solves overcrowding issues in a fusion reactor environment. Brought to a tabletop experiment, this cavity configuration is tested: a 4 mm beam width is obtained within a ≃1.5  m length cavity. The equivalent cavity g factor is measured to be 0.038(3), thus confirming the cavity stability.

Glaucoma in high myopia and parapapillary delta zone

PubMed Central

Weber, Pascal; Nagaoka, Natsuko; Ohno-Matsui, Kyoko

2017-01-01

Purpose To examine the prevalence of glaucomatous optic neuropathy (GON) in a medium myopic to highly myopic group of patients and its association with parapapillary gamma zone and parapapillary delta zone. Methods The retrospective observational hospital-based study included patients who had attended the Tokyo High Myopia Clinics within January 2012 and December 2012 and for whom fundus photographs were available. GON was defined based on the appearance of the optic nerve head on the fundus photographs. Results The study included 519 eyes (262 individuals) with a mean age of 62.0±14.3 years (range:13–89 years) and mean axial length of 29.5±2.2 mm (range:23.2–35.3mm). GON was present in 141 (27.2%; 95% confidence intervals (CI): 23.3, 31.0%) eyes. Prevalence of GON increased from 12.2% (1.7, 22.7) in eyes with an axial length of <26.5mm to 28.5% (24.4, 32.5) in eyes with an axial length of ≥26.5mm, to 32.6% (27.9, 37.2) in eyes with an axial length of ≥28mm, to 36.0% (30.5, 41.4) in eyes with an axial length of ≥29mm, and GON prevalence increased to 42.1% (35.5, 48.8) in eyes with an axial length of ≥30mm. In multivariate analysis, higher GON prevalence was associated (Nagelkerke r2: 0.28) with larger parapapillary delta zone diameter (P<0.001; odds ratio (OR):1.86;95%CI:1.33,2.61), longer axial length (P<0.001;OR:1.45;95%CI:1.26,1.67) and older age (P = 0.01;OR:1.03;95%CI:1.01,1.05). If parapapillary delta zone width was replaced by the vertical disc diameter, higher GON prevalence was associated (r2:0.24) with larger vertical optic disc diameter (P = 0.04;OR:1.70;95%CI:1.03,2.81), after adjusting for longer axial length (P<0.001;OR:1.44;95%CI:1.26,1.64) and older age (P<0.001;OR:1.04;95%CI:1.02,1.06). Conclusions Axial elongation associated increase in GON prevalence (mean: 28.1% in a medium to highly myopic study population) was associated with parapapillary delta zone as surrogate for an elongated peripapillary scleral flange and with larger optic disc size. PMID:28380081

Protein extraction from human anagen head hairs 1-millimeter or less in total length.

PubMed

Carlson, Traci L; Moini, Mehdi; Eckenrode, Brian A; Allred, Brent M; Donfack, Joseph

2018-04-01

A simple method for extracting protein from human anagen (i.e., actively growing hair stage) head hairs was developed in this study for cases of limited sample availability and/or studies of specific micro-features within a hair. The distinct feature segments of the hair from one donor were divided lengthwise (i.e., each of ∼200-400 μm) and then pooled for three individual hairs to form a total of eight composite hair samples (i.e., each of ∼1 mm or less in total length). The proteins were extracted, digested using trypsin, and characterized via nano-flow liquid chromatography tandem-mass spectrometry (nLC-MS/MS). A total of 63 proteins were identified from all eight protein samples analyzed of which 60% were keratin and keratin-associated proteins. The major hair keratins identified are consistent with previous studies using fluorescence in situ hybridization and nLC-MS/MS while requiring over 400-8000-fold less sample. The protein extraction method from micro-sized human head hairs described in this study will enable proteomic analysis of biological evidence for cases of limited sample availability and will complement hair research. For example, research seeking to develop alternative non-DNA based techniques for comparing questioned to known hairs, and understanding the biochemistry of hair decomposition.

SU-E-J-38: Improved DRR Image Quality Using Polyetheretherketone (PEEK) Fiducial in Image Guided Radiotherapy (IGRT)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, S; Jacob, R; Popple, R

Purpose Fiducial-based imaging is often used in IGRT. Traditional gold fiducial marker often has substantial reconstruction artifacts. These artifacts Result in poor image quality of DRR for online kV-to-DRR matching. This study evaluated the image quality of PEEK in DRR in static and moving phantom. Methods CT scan of the Gold and PEEK fiducial (both 1×3 mm) was acquired in a 22 cm cylindrical phantom filled with water. Image artifacts was evaluated with maximum CT value deviated from water due to artifacts; volume of artifacts in 10×10 cm in the center slice; maximum length of streak artifacts from the fiducial.more » DRR resolution were measured using FWHM and FWTM. 4DCT of PEEK fiducial was acquired with the phantom moving sinusoidally in superior-inferior direction. Motion artifacts were assessed for various 4D phase angles. Results The maximum CT value deviation was −174 for Gold and −24 for PEEK. The volume of artifacts in a 10x10 cm 3 mm slice was 0.369 for Gold and 0.074 cm3 for PEEK. The maximum length of streak artifact was 80mm for Gold and 7 mm for PEEK. PEEK in DRR, FWHM was close to actual (1.0 mm for Gold and 1.1 mm for PEEK). FWTM was 1.8 mm for Gold and 1.3 mm for PEEK in DRR. Barrel motion artifact of PEEK fiducial was noticeable for free-breathing scan. The apparent PEEK length due to residual motion was in close agreement with the calculated length (13 mm for 30–70 phase, 10 mm in 40–60 phase). Conclusion Streak artifacts on planning CT associated with use of gold fiducial can be significantly reduced by PEEK fiducial, while having adequate kV image contrast. DRR image resolution at FWTM was improved from 1.8 mm to 1.3 mm. Because of this improvement, we have been routinely use PEEK for liver IGRT.« less

"Reading man flap" design for reconstruction of circular infraorbital and malar skin defects.

PubMed

Seyhan, Tamer; Caglar, Baris

2008-11-01

Surgical complications such as lid retraction and ectropion from graft or flap scar contracture make reconstruction of skin defects in the malar and infraorbital regions challenging. A new flap design, the reading man flap, was used to overcome these problems. The Limberg and bilobed flap were compared with the reading man flap. The reading man flap consists mainly of a superiorly based quadrangular flap and an inferiorly based triangular flap. Malar and infraorbital circular skin defects measuring 14 x 14 to 40 x 40 mm were reconstructed with a reading man flap in 13 patients. The defects occurred after basal cell carcinoma in all patients. The Limberg flap, bilobed flap, and reading man flap were planned for same-sized defects on the abdominoplasty resection material. The results were compared in terms of total scar area, scar length, and total healthy skin area discarded. When comparing the 3 flap designs, the reading man flap was the most suitable flap in terms of total scar area and length. The reading man flap can be used to reconstruct malar and infraorbital circular defects with good cosmetic results and without creating any tractional forces to the eyelids.

Influence of Joint Configuration on the Strength of Laser Welded Presshardened Steel

NASA Astrophysics Data System (ADS)

Kügler, H.; Mittelstädt, C.; Vollertsen, F.

Presshardened steel is used in nowadays automotive production. Due to its high strength, sheet thicknesses can be reduced which results in decreasing weight of car body components. However, because of microstructure softening and coating agglomerations in the seam, welding is still a challenge. In this paper laser beam welding of 22MnB5 with varying energy input per irradiated area is presented. It is found that increasing energy input per seam length reduces tensile strength. Using a small spot size of 200 μm, tensile strength of 1434 N/mm2 can be reached in bead on plate welds. In lap welds tensile strength is limited because of coating particles agglomerating at the melt pool border line. However, the resulting strength is higher when using several small weld seams than using one seam with the same total seam width. With three weld seams, each 0.5mm in width, tensile strength of 911N/mm2 is reached in lap welding.

Development and clinical application of a length-adjustable water phantom for total body irradiation.

PubMed

Chen, Zhi-Wei; Yao, Sheng-Yu; Zhang, Tie-Ning; Zhu, Zhen-Hua; Hu, Zhe-Kai; Lu, Xun

2012-08-01

A new type of water phantom which would be specialised for the absorbed dose measurement in total body irradiation (TBI) treatment is developed. Ten millimetres of thick Plexiglas plates were arranged to form a square cube with 300 mm of edge length. An appropriate sleeve-type piston was installed on the side wall, and a tabular Plexiglas piston was positioned inside the sleeve. By pushing and pulling the piston, the length of the self-made water phantom could be varied to meet the required patients' physical sizes. To compare the international standard water phantom with the length-adjustable and the Plexiglas phantoms, absorbed dose for 6-MV X ray was measured by an ionisation chamber at different depths in three kinds of phantoms. In 70 cases with TBI, midplane doses were metered using the length-adjustable and the Plexiglas phantoms for simulating human dimensions, and dose validation was synchronously carried out. There were no significant statistical differences, p > 0.05, through statistical processing of data from the international standard water phantom and the self-designed one. There were significant statistical differences, p < 0.05, between the two sets of data from the standard and the Plexiglas one. In addition, the absolute difference had a positive correlation with the varied depth of the detector in the Plexiglas phantom. Comparing the data of clinical treatment, the differences were all <1 % among the prescription doses and the validation data collected from the self-design water phantom. However, the differences collected from the Plexiglas phantom were increasing gradually from +0.77 to +2.30 % along with increasing body width. Obviously, the difference had a positive correlation with the body width. The results proved that the new length-adjustable water phantom is more accurate for simulating human dimensions than Plexiglas phantom.

The association of calcaneal spur length and clinical and functional parameters in plantar fasciitis.

PubMed

Kuyucu, Ersin; Koçyiğit, Figen; Erdil, Mehmet

2015-09-01

Plantar fasciitis (PF)is the most common cause of plantar heel pain. Despite many treatment alternatives for heel spur, the association of calcaneal spur size with clinical and functional parameters is inconclusive. The objective of this study to investigate the correlation of calcaneal spur length with clinical findings and functional status documented with Foot Function Index in patients with plantar fasciitis. We performed power analysis for the sample size estimation. 87 patients with PF were scrutinized to reach the estimated patient number 75. Computer-aided linear measurements were done for spur length from tip to base in milimeters. Perceived pain intensity was evaluated by visual analog scale (VAS). Patients were asked to rate the pain experienced on a 10-cm VAS. Foot function index was applied to the patients to evaluate pain, disability and activity limitation of the patients. Of the 75 participants, 24 were males (32%) and 51 were females (68%). The mean age was 47 ± 10 years (range 30-65 years). The mean calcaneal spur length was 3.86 ± 3.36 mm (range between 0 and 12.2). Calcaneal spur length was significantly correlated with age (p = 0.003), BMI (p = 0.029), symptom duration, (p = 0.001) VAS (p = 0.003), and FFI total score (p < 0.001). Our study demonstrated that length of the calcaneal spur is significantly correlated with age, BMI, symptom duration, perceived pain, FFI pain and disability subscores, and FFI total scores. The size of the calcaneal spur is an important parameter correlated with pain and functional scores in PF. Copyright © 2015 IJS Publishing Group Limited. Published by Elsevier Ltd. All rights reserved.

Preoperative digital planning versus postoperative outcomes in total hip arthroplasty using a calcar-guided short stem: frequent valgization can be avoided.

PubMed

Kutzner, Karl Philipp; Pfeil, Joachim; Kovacevic, Mark Predrag

2017-07-01

Modern total hip arthroplasty is largely dependent on the successful preservation of hip geometry. Thus, a successful implementation of the preoperative planning is of great importance. The present study evaluates the accuracy of anatomic hip reconstruction predicted by 2D digital planning using a calcar-guided short stem of the newest generation. A calcar-guided short stem was implanted in 109 patients in combination with a cementless cup using the modified anterolateral approach. Preoperative digital planning was performed including implant size, caput-collum-diaphyseal angle, offset, and leg length using mediCAD II software. A coordinate system and individual scale factors were implemented. Postoperative outcome was evaluated accordingly and was compared to the planning. Intraoperatively used stem sizes were within one unit of the planned stem sizes. The postoperative stem alignment showed a minor and insignificant (p = 0.159) mean valgization of 0.5° (SD 3.79°) compared to the planned caput-collum-diaphyseal angles. Compared to the planning, mean femoral offset gained 2.18 (SD 4.24) mm, while acetabular offset was reduced by 0.78 (SD 4.36) mm during implantation resulting in an increased global offset of 1.40 (SD 5.51) mm (p = 0.0094). Postoperative femoroacetabular height increased by a mean of 5.00 (SD 5.98) mm (p < 0.0001) compared to preoperative measures. Two-dimensional digital preoperative planning in calcar-guided short-stem total hip arthroplasty assures a satisfying implementation of the intended anatomy. Valgization, which has been frequently observed in previous short-stem designs, negatively affecting offset, can be avoided. However, surgeons have to be aware of a possible leg lengthening.

Percutaneous nephrolithotomy vs. extracorporeal shockwave lithotripsy for treating a 20-30 mm single renal pelvic stone.

PubMed

Hassan, Mohammed; El-Nahas, Ahmed R; Sheir, Khaled Z; El-Tabey, Nasr A; El-Assmy, Ahmed M; Elshal, Ahmed M; Shokeir, Ahmed A

2015-09-01

To compare the efficacy, safety and cost of extracorporeal shockwave lithotripsy (ESWL) and percutaneous nephrolithotomy (PNL) for treating a 20-30 mm single renal pelvic stone. The computerised records of patients who underwent PNL or ESWL for a 20-30 mm single renal pelvic stone between January 2006 and December 2012 were reviewed retrospectively. Patients aged <18 years who had a branched stone, advanced hydronephrosis, a solitary kidney, anatomical renal abnormality, or had a surgical intervention within the past 6 months were excluded. The study included 337 patients with a mean (SD, range) age of 49.3 (12.2, 20-81) years. The patients' criteria (age, sex, body mass index) and the stone characteristics (side, stone length, surface area, attenuation value and skin-to-stone distance) were compared between the groups. The re-treatment rate, the need for secondary procedures, success rate, complications and the total costs were calculated and compared. In all, 167 patients were treated by ESWL and 170 by PNL. The re-treatment rate (75% vs. 5%), the need for secondary procedures (25% vs. 4.7%) and total number of procedures (three vs. one) were significantly higher in the ESWL group (P < 0.001). The success rate was significantly higher in the PNL group (95% vs. 75%, P < 0.001), as was the complication rate (13% vs. 6.6%, P = 0.050). The total costs of primary and secondary procedures were significantly higher for PNL (US$ 1120 vs. 490; P < 0.001). PNL was more effective than ESWL for treating a single renal pelvic stone of 20-30 mm. However, ESWL was associated with fewer complications and a lower cost.

A Piezoelectric Micromotor with a Stator of φ=1.6 mm and l=4 mm Using Bulk PZT

NASA Astrophysics Data System (ADS)

Cagatay, Serra; Koc, Burhanettin; Moses, Paul; Uchino, Kenji

2004-04-01

The smallest discrete piezoelectric ultrasonic motor using bulk ceramics was developed. We are proposing basically a two-part motor: stator and rotor. The stator of the present motor consists of a hollow metal brass tube with outer diameter of 1.6 mm, inner diameter of 0.8 mm and length of only 4 mm with 2 PZT plates bonded onto it. Owing to the asymmetrical stator surface, two degenerated orthogonal bending modes were slightly split, resulting in a wobbling motion. Thus, the motor can be driven by a single driving source. The rotor is a spring, which is basically different from previous designs, pressed at both ends to the stator by a pair of ferrules. Consequently, the length of the whole motor assembly was reduced significantly; a final motor length of only 5 mm was obtained. The working frequency under zero load was approximately 227-233 kHz. Although the size is small, relatively high power was obtained under an optimized load condition: torque of 0.06 mNm, maximum power of 3.2 mW with a speed of 118 rad/s, and maximum efficiency of 11% under 48 Vrms at 221 kHz.

Fabrication and mechanical characterization of long and different penetrating length neural microelectrode arrays

NASA Astrophysics Data System (ADS)

Goncalves, S. B.; Peixoto, A. C.; Silva, A. F.; Correia, J. H.

2015-05-01

This paper presents a detailed description of the design, fabrication and mechanical characterization of 3D microelectrode arrays (MEA) that comprise high aspect-ratio shafts and different penetrating lengths of electrodes (from 3 mm to 4 mm). The array’s design relies only on a bulk silicon substrate dicing saw technology. The encapsulation process is accomplished by a medical epoxy resin and platinum is used as the transduction layer between the probe and neural tissue. The probe’s mechanical behaviour can significantly affect the neural tissue during implantation time. Thus, we measured the MEA maximum insertion force in an agar gel phantom and a porcine cadaver brain. Successful 3D MEA were produced with shafts of 3 mm, 3.5 mm and 4 mm in length. At a speed of 180 mm min-1, the MEA show maximum penetrating forces per electrode of 2.65 mN and 12.5 mN for agar and brain tissue, respectively. A simple and reproducible fabrication method was demonstrated, capable of producing longer penetrating shafts than previously reported arrays using the same fabrication technology. Furthermore, shafts with sharp tips were achieved in the fabrication process simply by using a V-shaped blade.

Ascending aortic elongation and the risk of dissection.

PubMed

Krüger, Tobias; Forkavets, Oksana; Veseli, Kujtim; Lausberg, Henning; Vöhringer, Luise; Schneider, Wilke; Bamberg, Fabian; Schlensak, Christian

2016-08-01

Unlike aneurysm formation, the role of ascending aortic elongation in the pathogenesis of Type A aortic dissection (TAD) is largely unclear. We investigated the morphology of healthy, dissected and predissection aortas with a focus on ascending aortic length. We retrospectively compared clinical and computer tomography angiography (CTA) data from TAD patients (n = 130), patients who developed a TAD in the further clinical course (preTAD, n = 16) and healthy control patients who received a CTA for non-aortic emergencies (n = 165). The length of the ascending aorta was defined as the distance between the sinotubular junction (STJ) and the brachiocephalic trunk (BCT) at the central line, the outer and inner curvature as well as the direct distance in the frontal and sagittal planes. Additionally, the aortic diameters were analysed. In the healthy controls, we found a positive correlation of age with the aortic diameter (r = 0.57) and aortic length (r = 0.42). The correlation of the respective parameters with the body size was negligible (r < 0.2). The median ascending aortic diameter at the height of the pulmonary artery in TAD (50 mm) was significantly (P < 0.001) larger compared with the respective diameter of the healthy aortas (34 mm). The diameter of the preTAD aortas (40 mm) was also significantly larger compared with the healthy controls. These proportions were similar in all the aortic diameters. The midline length of the healthy ascending aortas was 71 mm. In the preTAD and TAD aortas, the same values were 81 mm and 92 mm, respectively (both P < 0.001). We evaluated the linear distance between the STJ and the BCT in the frontal plane as an easy-to-measure parameter of aortic length. In the TAD aortas (108 mm) and preTAD aortas (97 mm), this distance was significantly longer compared with the healthy aortas (84 mm). Aortic diameter might not be an optimal parameter to predict dissection. Most aortas dissect at diameters below 55 mm. Both the TAD and preTAD aortas were elongated compared with the healthy controls. Thus, aortic elongation may play a role in the pathogenesis of and may be a risk factor for TAD. © The Author 2016. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Age-related changes in optical and biometric characteristics of emmetropic eyes.

PubMed

Atchison, David A; Markwell, Emma L; Kasthurirangan, Sanjeev; Pope, James M; Smith, George; Swann, Peter G

2008-04-28

We measured optical and biometric parameters of emmetropic eyes as a function of age. There were approximately 20 subjects each in age groups 18-29, 30-39, 40-49, 50-59, and 60-69 years with similar male and female numbers. One eye was tested for each subject, having spherical equivalent in the range -0.88 D to +0.75 D and

[Microsurgical anatomy importance of A1-anterior communicating artery complex].

PubMed

Monroy-Sosa, Alejandro; Pérez-Cruz, Julio César; Reyes-Soto, Gervith; Delgado-Hernández, Carlos; Macías-Duvignau, Mario Alberto; Delgado-Reyes, Luis

2013-01-01

The anterior cerebral artery originates from the bifurcation of the internal carotid artery lateral to the optic chiasm, then joins with its contralateral counterpart via the anterior communicating artery. A1-anterior communicating artery complex is the most frequent anatomical variants and is the major site of aneurysms between 30 to 37%. Know the anatomy microsurgical, variants anatomical and importance of complex precommunicating segment-artery anterior communicating in surgery neurological of the pathology vascular, mainly aneurysms, in Mexican population. The study was performed in 30 brains injected. Microanatomy was studied (length and diameter) of A1-anterior communicating artery complex and its variants. 60 segments A1, the average length of left side was 11.35 mm and 11.84 mm was right. The average diameter of left was 1.67 mm and the right was 1.64 mm. The average number of perforators on the left side was 7.9 and the right side was 7.5. Anterior communicating artery was found in 29 brains of the optic chiasm, its course depended on the length of the A1 segment. The average length of the segment was 2.84 mm, the average diameter was 1.41 mm and the average number of perforators was 3.27. A1-anterior communicating artery complex variants were found in 18 (60%) and the presence of two blister-like aneurysms. It is necessary to understand the A1-anterior communicating artery complex microanatomy of its variants to have a three-dimensional vision during aneurysm surgery.

Reference ranges for foetal nasal bone length, prenasal thickness, and interocular distance at 18 to 24 weeks' gestation in low-risk pregnancies.

PubMed

Altunkeser, Ayşegül; Körez, M Kazım

2017-12-12

The aim of the present study was to establish the normal ranges for foetal nasal bone length (NBL), prenasal skin thickness (PNT), interocular distance (IOD), and ratio of prenasal thickness to- nasal bone length (PNT/ NBL) at 18-24 weeks using two-dimensional (2D) ultrasound. This study was a retrospective study of prenatal ultrasonographic records from 407 foetuses between 18 and 24 weeks gestational age (GA). The NBL, PNT, IOD, PNT/ NBL ratio, biparietal diameter (BPD), and femur length (FL) were investigated. The relationships among NBL, PNT, IOD, PNT/ NBL, and GA were evaluated. Additionally, descriptive statistics for NBL, PNT, and IOD values for each gestational week were obtained. There was a significant association between GA and NBL, PNT, and IOD between 18 and 24 weeks. NBL increased from a mean of 5.5 mm to 8.3 mm, PNT increased from a mean of 3.5 mm to 5.1 mm, and IOD increased from a mean of 11.1 mm to 14.5 mm. PNT/NBL ratio did not change with gestational age. This study showed normal ranges for NBL, PNT, IOD, and PNT/ NBL ratios for foetuses between 18 and 24 weeks in low-risk pregnancies. There was a positive linear relationship between GA and NBL, PNT, and IOD. The PNT/NBL ratio might be a more useful measurement than NBL or PNT alone.

Transvaginal cervical length and tobacco use in Appalachian women: association with increased risk for spontaneous preterm birth.

PubMed

Findley, Joseph; Seybold, Dara J; Broce, Mike; Yadav, Dolly; Calhoun, Byron C

2015-01-01

Currently ACOG recommends that a mid-term screening strategy may be considered to identify short cervix in low risk populations in an effort to prevent preterm birth. Vaginal progesterone is recommended for women with a cervical length ≤20 mm. Cerclage is recommended for women with prior spontaneous preterm birth who are already receiving progesterone supplementition and CL is <25 mm. This study examined risk factors for spontaneous preterm birth (SPB) <35 weeks among a general obstetrical population prior to these ACOG recommendations. However, cervical cerclage was a possible intervention. Study population included 1,074 patients from 1 Jan 2007-30 Jun 2008 receiving mid-trimester transvaginal ultrasounds during prenatal care at a tertiary medical center clinic. Receiver operator characteristic (ROC) curve cutoff optimal value was ≤34 mm, (n=224), corresponding to 8.9% SPB with shortened cervices compared to 1.4% in patients with normal cervices (>34 mm; n=850; p<0.001 (Area Under the Curve (AUC) 76.6, p<0.001). Cervical lengths <30 mm had 12 times the risk of SPB (p<0.001) while 30-34 mm had 5 times (p=0.005). Tobacco use (≥10 cigarettes per day), p=0.030, and low BMI, p=0.034, had additive effect. Shortened cervical length during routine screening independently predicted SPB while heavy smoking with shortened cervix during pregnancy doubled risk compared to shortened cervix alone.

Transvaginal Cervical Length and Tobacco Use in Appalachian Women: Association with Increased Risk for Spontaneous Preterm Birth

PubMed Central

Findley, Joseph; Seybold, Dara J.; Broce, Mike; Yadav, Dolly; Calhoun, Byron C.

2015-01-01

Currently ACOG recommends that a mid-term screening strategy may be considered to identify short cervix in low risk populations in an effort to prevent preterm birth. Vaginal progesterone is recommended for women with a cervical length ≤20 mm. Cerclage is recommended for women with prior spontaneous preterm birth who are already receiving progesterone supplementation and CL is <25 mm. This study examined risk factors for spontaneous preterm birth (SPB) <35 weeks among a general obstetrical population prior to these ACOG recommendations. However, cervical cerclage was a possible intervention. Study population included 1,074 patients from 1 Jan 2007-30 Jun 2008 receiving mid-trimester transvaginal ultrasounds during prenatal care at a tertiary medical center clinic. Receiver operator characteristic (ROC) curve cutoff optimal value was ≤34 mm, (n=224), corresponding to 8.9% SPB with shortened cervices compared to 1.4% in patients with normal cervices (>34 mm; n=850; p<0.001 (Area Under the Curve (AUC) 76.6, p<0.001). Cervical lengths <30 mm had 12 times the risk of SPB (p<0.001) while 30-34 mm had 5 times (p=0.005). Tobacco use (≥10 cigarettes per day), p=0.030, and low BMI, p=0.034, had additive effect. Shortened cervical length during routine screening independently predicted SPB while heavy smoking with shortened cervix during pregnancy doubled risk compared to shortened cervix alone. PMID:26050294

Assessment of intraocular measurements in neonatal foals and association with gender, laterality, and body weight: a clinical study.

PubMed

Valentini, Simona; Castagnetti, Carolina; Musella, Vincenzo; Spinella, Giuseppe

2014-01-01

Objective of this study was to describe intraocular measurements in newly born foals (1-7 days of age) and assess the association between globe measurements and gender, laterality, and body weight. B-scan ultrasonographic biometry was performed on both eyes of 22 healthy foals (44 eyes) ages 1-7 days using a 10-MHz transducer. Intraocular measurements (anterior chamber depth, central lens thickness, vitreous chamber depth, axial globe length, longitudinal globe length, lens poles distance) were carried out using the ultrasound internal calipers. The influence of gender (male or female), laterality (right or left eye), and body weight ("light" <48 kg; "heavy" ≥48 kg) on ocular measurements was analysed by the Student t test. Values of P<0.05 were accepted as significant for all analyses. Mean anterior chamber depth was 2.2±0.5 mm (Standard Deviation); central lens thickness was 9.9±0.8 mm; vitreous chamber depth was 15.5±1.1 mm; axial globe length was 27.6±1.6 mm; longitudinal globe length was 35.8±1.2 mm, and lens poles distance was 16.4±1.0 mm. Intraocular measurements were not influenced by gender, laterality nor body weight. This study provides reference values for intraocular measurements in neonatal foals and may be useful in the diagnosis and treatment of congenital and acquired pathologies involving the globe.

Assessment of Intraocular Measurements in Neonatal Foals and Association with Gender, Laterality, and Body Weight: A Clinical Study

PubMed Central

Valentini, Simona; Castagnetti, Carolina; Musella, Vincenzo; Spinella, Giuseppe

2014-01-01

Objective of this study was to describe intraocular measurements in newly born foals (1–7 days of age) and assess the association between globe measurements and gender, laterality, and body weight. B-scan ultrasonographic biometry was performed on both eyes of 22 healthy foals (44 eyes) ages 1–7 days using a 10-MHz transducer. Intraocular measurements (anterior chamber depth, central lens thickness, vitreous chamber depth, axial globe length, longitudinal globe length, lens poles distance) were carried out using the ultrasound internal calipers. The influence of gender (male or female), laterality (right or left eye), and body weight (“light” <48 kg; “heavy” ≥48 kg) on ocular measurements was analysed by the Student t test. Values of P<0.05 were accepted as significant for all analyses. Mean anterior chamber depth was 2.2±0.5 mm (Standard Deviation); central lens thickness was 9.9±0.8 mm; vitreous chamber depth was 15.5±1.1 mm; axial globe length was 27.6±1.6 mm; longitudinal globe length was 35.8±1.2 mm, and lens poles distance was 16.4±1.0 mm. Intraocular measurements were not influenced by gender, laterality nor body weight. This study provides reference values for intraocular measurements in neonatal foals and may be useful in the diagnosis and treatment of congenital and acquired pathologies involving the globe. PMID:25296286

Design study of electron cyclotron resonance-ion plasma accelerator for heavy ion cancer therapy.

PubMed

Inoue, T; Hattori, T; Sugimoto, S; Sasai, K

2014-02-01

Electron Cyclotron Resonance-Ion Plasma Accelerator (ECR-IPAC) device, which theoretically can accelerate multiple charged ions to several hundred MeV with short acceleration length, has been proposed. The acceleration mechanism is based on the combination of two physical principles, plasma electron ion adiabatic ejection (PLEIADE) and Gyromagnetic Autoresonance (GYRAC). In this study, we have designed the proof of principle machine ECR-IPAC device and simulated the electromagnetic field distribution generating in the resonance cavity. ECR-IPAC device consisted of three parts, ECR ion source section, GYRAC section, and PLEIADE section. ECR ion source section and PLEIADE section were designed using several multi-turn solenoid coils and sextupole magnets, and GYRAC section was designed using 10 turns coil. The structure of ECR-IPAC device was the cylindrical shape, and the total length was 1024 mm and the maximum diameter was 580 mm. The magnetic field distribution, which maintains the stable acceleration of plasma, was generated on the acceleration center axis throughout three sections. In addition, the electric field for efficient acceleration of electrons was generated in the resonance cavity by supplying microwave of 2.45 GHz.

Evaluation of potentially nonlethal sampling methods for monitoring mercury concentrations in smallmouth bass (Micropterus dolomieu)

USGS Publications Warehouse

Schmitt, C.J.; Brumbaugh, W.G.

2007-01-01

We evaluated three potentially nonlethal alternatives to fillet sampling for the determination of mercury (Hg) concentrations in smallmouth bass (Micropterus dolomieu). Fish (n = 62, 226-464 mm total length) from six sites in southern Missouri were captured by electrofishing. Blood samples (1 mL) from each fish were obtained by caudal veinipuncture with a heparinized needle and syringe. Biopsy needle (10 mm x 14 gauge; three cuts per fish; 10-20 mg total dry weight) and biopsy punch (7 mm x 5 mm in diameter, one plug per fish, 30-50 mg dry weight) samples were obtained from the area beneath the dorsal fin. Fillet samples were obtained from the opposite side of the fish. All samples were freeze-dried and analyzed for total Hg by combustion amalgamation atomic absorption spectrophotometry. Mean relative standard deviations (RSDs) of triplicate samples were similar for all four methods (2.2-2.4%), but the range of RSDs was greater for blood (0.4-5.5%) than for the muscle methods (1.8-4.0%). Total Hg concentrations in muscle were 0.0200-0.8809 ??g/g wet weight; concentrations in plug, needle, and fillet samples from each fish were nearly identical. Blood Hg concentrations were 0.0006-0.0812 ??g/mL and were highly correlated with muscle concentrations; linear regressions between log-transformed blood and fillet Hg concentrations were linear and statistically significant (p < 0.01), and explained 91-93% of the total variation. Correlations between fillet Hg concentrations and fish size and age were weak; together they explained ???37% of the total variation, and the relations differed among sites. Overall, any of the alternative methods could provide satisfactory estimates of fillet Hg in smallmouth bass; however, both blood and plug sampling with disposable instruments were easier to perform than needle sampling. The biopsy needle was the most difficult to use, especially on smaller fish, and its relative expense necessitates reuse and, consequently, thorough cleaning between fish to prevent cross-contamination. ?? 2007 Springer Science+Business Media, LLC.

The fish community of a small impoundment in upstate New York

USGS Publications Warehouse

McCoy, C. Mead; Madenjian, Charles P.; Adams, Jean V.; Harman, Willard N.

2001-01-01

Moe Pond is a dimictic impoundment with surface area of 15.6 ha, a mean depth of 1.8 m, and an unexploited fish community of only two species: brown bullhead (Ameiurus nebulosus) and golden shiner (Notemigonus crysoleucas). The age-1 and older brown bullhead population was estimated to be 4,057 individuals, based on the Schnabel capture-recapture method of population estimation. Density and biomass were respectively estimated at 260 individuals/ha and 13 kg/ha. Annual survival rate of age-2 through age-5 brown bullheads was estimated at 48%. The golden shiner length-frequency distribution was unimodal with modal length of 80 mm and maximum total length of 115 m. The golden shiner population estimate was 7,154 individuals, based on seven beach seine haul replicate samples; the density and biomass were 686 shiners/ha and 5 kg/ha, respectively. This study provides an information baseline that may be useful in understanding food web interactions and whole-pond nutrient flux.

[Reproduction of the pink shrimp Farfantepenaeus notialis (Decapoda: Penaeidae) in the Colombian Caribbean].

PubMed

Paramo, Jorge; Pérez, Daniel; Wolff, Matthias

2014-06-01

The shallow water pink shrimp (Farfantepenaeus notialis) is among the socioeconomically most important resources of the Caribbean. The lack of biological and fishery information is of great concern for the fisheries management authorities. The presented study therefore aimed at the investigation of the reproductive cycle, the size composition and the size at first maturity of this species as a basis for the ordination and management of this resource. The study was conducted from June 2012 to May 2013 off the coast of the Caribbean Sea of Colombia. A total of 5 356 individuals were collected, identified, classified and preserved for their subsequent analysis in the laboratory. Size, weight, sex and gonad stage were recorded for each specimen. Significant differences were found in sex ratio in all months sampled with a clear predominance of females. Mature females were found year-around, but two reproductive peaks were identified during the periods October-December and April-June. The mean catch total length size (MCS) for females and males was 148.00mm and 122.54mm, respectively. The mean size at maturity (LT50%) was 129.34mm for females and 97.77mm for males. MCS was always above LT50% for both sexes. Considering the large reduction in fishing effort in the Colombian Caribbean Sea over the last years, we could expect that the shrimp population is in a rebuilding process or perhaps it may be already restored.

All-Printed Differential Temperature Sensor for the Compensation of Bending Effects.

PubMed

Ali, Shawkat; Hassan, Arshad; Bae, Jinho; Lee, Chong Hyun; Kim, Juho

2016-11-08

Because printed resistance temperature detectors (RTDs) are affected by tension and compression of metallic patterns on flexible or curved surfaces, a significant temperature-sensing error occurs in general. Hence, we propose a differential temperature sensor (DTS) to compensate the bending effect of the printed RTDs, which is composed of two serially connected similar meander patterns fabricated back-to-back on a polyimide polyethylene terephthalate substrate through a Dimatix DMP-3000 inkjet printer using silver nanoparticles. Under mechanical deformation, the resistance of the proposed DTS is not varied significantly under the same temperature environment because its patterns vary differentially as one side experiences tension while the opposite side experiences compression. A single meander pattern of the proposed DTS has a total length of 75 mm and device dimensions of 7 × 7 mm 2 . The total resistance variation is observed to be 15.5 Ω against the temperature variation from 0 to 100 °C, and the temperature coefficient of resistance is 1.076 × 10 -3 °C -1 . The proposed DTS exhibits no significant resistance change on bendability testing down to 2 mm diameter because of mechanical deformation. In addition, it is also used to detect the curvature of a body shape down to 2 mm diameter because its resistance changes by ±8.22% using a single meander pattern of DTS. The proposed sensor can be applied on a curved or flexible surface to measure relatively accurate temperature when compared to a single meander pattern.

Tag retention, growth, and survival of red swamp crayfish Procambarus clarkii marked with coded wire tags

USGS Publications Warehouse

Isely, J.J.; Eversole, A.G.

1998-01-01

Juvenile red swamp crayfish (or crawfish), Procambarus clarkii (20-41 mm in total length) were collected from a crayfish culture pond by dipnetting and tagged with sequentially numbered, standard length, binary-coded wire tags. Four replicates of 50 crayfish were impaled perpendicular to the long axis of the abdomen with a fixed needle. Tags were injected transversely into the ventral surface of the first or second abdominal segment and were imbedded in the musculature just beneath the abdominal sternum. Tags were visible upon inspection. Additionally, two replicates of 50 crayfish were not tagged and were used as controls. Growth, survival, and tag retention were evaluated after 7 d in individual containers, after 100 d in aquaria, and after 200 d in field cages. Tag retention during each sample period was 100%, and average mortality of tagged crayfish within 7 d of tagging was 1%. Mortality during the remainder of the study was high (75-91%) but was similar between treatment and control samples. Most of the deaths were probably due to cannibalism. Average total length increased threefold during the course of the study, and crayfish reached maturity. Because crayfish were mature by the end of the study, we concluded that the coded wire tag was retained through the life history of the crayfish.

High-intensity soft-flash x-ray generator utilizing a low-vacuum diode

NASA Astrophysics Data System (ADS)

Isobe, Hiroshi; Sato, Eiichi; Shikoda, Arimitsu; Takahashi, Kei; Tamakawa, Yoshiharu; Yanagisawa, Toru

1991-04-01

The fundamental studies on the high-intensity single flash x-ray generator having a low-vacuum diode for biomedical radiography are described. This generator consisted of the following essential components: a high-voltage power supply, a high-voltage pulser with a coaxial oil condenser of l5OnF, a low impedance transmission line made from four coaxial cables with lengths of 5. 6m and a total capacity of 292OpF, a mechanical booster pump, and a flash x-ray tube. The x-ray tube was of the diode-type which was connected to the booster pump with a constant pressure of 1. 7Pa and consisted of the following major devices: a long anode tip made of tungsten with a diameter (D) of less than 3. 0mm and a length (L) of 50mm, a long cathode tip made of tungsten with a D of 1. 0mm and a L of 40mm, a polyoxymethylene insulator, lead diaphragms, and an x-ray window made of polyethylene terephthalate. The coaxial oil condenser in the pulser was charged from 50 to 90kV, and the electric charges in the condenser were discharged to the flash x-ray tube through a transmission line by using a gas gap switch with a highcurrent capacity. The peak voltage increased according to increases in the condenser charged voltage and its value was more than the charged voltage. The peak current primarily increased when the charged voltage was increased, and its value was less than 4OkA. The pulse width of the flash x-rays ranged from 60 to 8Ons, and the time integrated x-ray intensity with a charged voltage of 90kV and an anode cathode (A-C) space of 3. 0mm was about 4pC/kg at 1. Om per pulse the source. The effective focal spot size was primarily determined by the diameter of the anode tip, and its value was about 3. 0mm when an anode diameter of 3. 0mm was employed.

Frequency Response of Synthetic Vocal Fold Models with Linear and Nonlinear Material Properties

PubMed Central

Shaw, Stephanie M.; Thomson, Scott L.; Dromey, Christopher; Smith, Simeon

2014-01-01

Purpose The purpose of this study was to create synthetic vocal fold models with nonlinear stress-strain properties and to investigate the effect of linear versus nonlinear material properties on fundamental frequency during anterior-posterior stretching. Method Three materially linear and three materially nonlinear models were created and stretched up to 10 mm in 1 mm increments. Phonation onset pressure (Pon) and fundamental frequency (F0) at Pon were recorded for each length. Measurements were repeated as the models were relaxed in 1 mm increments back to their resting lengths, and tensile tests were conducted to determine the stress-strain responses of linear versus nonlinear models. Results Nonlinear models demonstrated a more substantial frequency response than did linear models and a more predictable pattern of F0 increase with respect to increasing length (although range was inconsistent across models). Pon generally increased with increasing vocal fold length for nonlinear models, whereas for linear models, Pon decreased with increasing length. Conclusions Nonlinear synthetic models appear to more accurately represent the human vocal folds than linear models, especially with respect to F0 response. PMID:22271874

Frequency response of synthetic vocal fold models with linear and nonlinear material properties.

PubMed

Shaw, Stephanie M; Thomson, Scott L; Dromey, Christopher; Smith, Simeon

2012-10-01

The purpose of this study was to create synthetic vocal fold models with nonlinear stress-strain properties and to investigate the effect of linear versus nonlinear material properties on fundamental frequency (F0) during anterior-posterior stretching. Three materially linear and 3 materially nonlinear models were created and stretched up to 10 mm in 1-mm increments. Phonation onset pressure (Pon) and F0 at Pon were recorded for each length. Measurements were repeated as the models were relaxed in 1-mm increments back to their resting lengths, and tensile tests were conducted to determine the stress-strain responses of linear versus nonlinear models. Nonlinear models demonstrated a more substantial frequency response than did linear models and a more predictable pattern of F0 increase with respect to increasing length (although range was inconsistent across models). Pon generally increased with increasing vocal fold length for nonlinear models, whereas for linear models, Pon decreased with increasing length. Nonlinear synthetic models appear to more accurately represent the human vocal folds than do linear models, especially with respect to F0 response.

Influence of Clinical Factors and Magnification Correction on Normal Thickness Profiles of Macular Retinal Layers Using Optical Coherence Tomography.

PubMed

Higashide, Tomomi; Ohkubo, Shinji; Hangai, Masanori; Ito, Yasuki; Shimada, Noriaki; Ohno-Matsui, Kyoko; Terasaki, Hiroko; Sugiyama, Kazuhisa; Chew, Paul; Li, Kenneth K W; Yoshimura, Nagahisa

2016-01-01

To identify the factors which significantly contribute to the thickness variabilities in macular retinal layers measured by optical coherence tomography with or without magnification correction of analytical areas in normal subjects. The thickness of retinal layers {retinal nerve fiber layer (RNFL), ganglion cell layer plus inner plexiform layer (GCLIPL), RNFL plus GCLIPL (ganglion cell complex, GCC), total retina, total retina minus GCC (outer retina)} were measured by macular scans (RS-3000, NIDEK) in 202 eyes of 202 normal Asian subjects aged 20 to 60 years. The analytical areas were defined by three concentric circles (1-, 3- and 6-mm nominal diameters) with or without magnification correction. For each layer thickness, a semipartial correlation (sr) was calculated for explanatory variables including age, gender, axial length, corneal curvature, and signal strength index. Outer retinal thickness was significantly thinner in females than in males (sr2, 0.07 to 0.13) regardless of analytical areas or magnification correction. Without magnification correction, axial length had a significant positive sr with RNFL (sr2, 0.12 to 0.33) and a negative sr with GCLIPL (sr2, 0.22 to 0.31), GCC (sr2, 0.03 to 0.17), total retina (sr2, 0.07 to 0.17) and outer retina (sr2, 0.16 to 0.29) in multiple analytical areas. The significant sr in RNFL, GCLIPL and GCC became mostly insignificant following magnification correction. The strong correlation between the thickness of inner retinal layers and axial length appeared to result from magnification effects. Outer retinal thickness may differ by gender and axial length independently of magnification correction.

Influence of Clinical Factors and Magnification Correction on Normal Thickness Profiles of Macular Retinal Layers Using Optical Coherence Tomography

PubMed Central

Higashide, Tomomi; Ohkubo, Shinji; Hangai, Masanori; Ito, Yasuki; Shimada, Noriaki; Ohno-Matsui, Kyoko; Terasaki, Hiroko; Sugiyama, Kazuhisa; Chew, Paul; Li, Kenneth K. W.; Yoshimura, Nagahisa

2016-01-01

Purpose To identify the factors which significantly contribute to the thickness variabilities in macular retinal layers measured by optical coherence tomography with or without magnification correction of analytical areas in normal subjects. Methods The thickness of retinal layers {retinal nerve fiber layer (RNFL), ganglion cell layer plus inner plexiform layer (GCLIPL), RNFL plus GCLIPL (ganglion cell complex, GCC), total retina, total retina minus GCC (outer retina)} were measured by macular scans (RS-3000, NIDEK) in 202 eyes of 202 normal Asian subjects aged 20 to 60 years. The analytical areas were defined by three concentric circles (1-, 3- and 6-mm nominal diameters) with or without magnification correction. For each layer thickness, a semipartial correlation (sr) was calculated for explanatory variables including age, gender, axial length, corneal curvature, and signal strength index. Results Outer retinal thickness was significantly thinner in females than in males (sr2, 0.07 to 0.13) regardless of analytical areas or magnification correction. Without magnification correction, axial length had a significant positive sr with RNFL (sr2, 0.12 to 0.33) and a negative sr with GCLIPL (sr2, 0.22 to 0.31), GCC (sr2, 0.03 to 0.17), total retina (sr2, 0.07 to 0.17) and outer retina (sr2, 0.16 to 0.29) in multiple analytical areas. The significant sr in RNFL, GCLIPL and GCC became mostly insignificant following magnification correction. Conclusions The strong correlation between the thickness of inner retinal layers and axial length appeared to result from magnification effects. Outer retinal thickness may differ by gender and axial length independently of magnification correction. PMID:26814541

Laparoscopic prototype for optical sealing of renal blood vessels

NASA Astrophysics Data System (ADS)

Hardy, Luke A.; Hutchens, Thomas C.; Larson, Eric R.; Gonzalez, David A.; Chang, Chun-Hung; Nau, William H.; Fried, Nathaniel M.

2017-02-01

Energy-based, radiofrequency and ultrasonic devices provide rapid sealing of blood vessels during laparoscopic procedures. We are exploring infrared lasers as an alternative for vessel sealing with less collateral thermal damage. Previous studies demonstrated vessel sealing in an in vivo porcine model using a 1470-nm laser. However, the initial prototype was designed for open surgery and featured tissue clasping and light delivery mechanisms incompatible with laparoscopic surgery. In this study, a laparoscopic prototype similar to devices in surgical use was developed, and tests were conducted on porcine renal blood vessels. The 5-mm-OD prototype featured a traditional Maryland jaw configuration. Laser energy was delivered through a 550-μm-core fiber and side-delivery from the lower jaw, with beam dimensions of 18-mm-length x 1.2-mm-width. The 1470-nm diode laser delivered 68 W with 3 s activation time. A total of 69 porcine renal vessels with mean diameter of 3.3 +/- 1.7 mm were tested, ex vivo. Vessels smaller than 5 mm were consistently sealed (48/51) with burst pressures greater than malignant hypertension blood pressure (180 mmHg), averaging 1038 +/- 474 mmHg. Vessels larger than 5 mm were not consistently sealed (6/18), yielding burst pressures of only 174 +/- 221 mmHg. Seal width, thermal damage zone, and thermal spread averaged 1.7 +/- 0.8, 3.4 +/- 0.7, and 1.0 +/- 0.4 mm. A novel optical laparoscopic prototype with 5-mm- OD shaft integrated within a standard Maryland jaw design consistently sealed vessels less than 5 mm with minimal thermal spread. Further in vivo studies are planned to test performance across a variety of vessels and tissues.

The first record of the slender sunfish Ranzania laevis from the Red Sea.

PubMed

Abu El-Regal, M A; El-Moselhy, K

2013-11-01

A female specimen of the slender sunfish Ranzania laevis of 600 mm total length was recorded for the first time from the Red Sea after being stranded on a shallow sandy bay at Hurghada beach (27° 06' 16″ N; 33° 50' 01″ E) on 13 May 2012. Ranzania laevis is believed to have migrated from the Indian Ocean as the nearest area where it was found is coastal waters of Oman. © 2013 The Fisheries Society of the British Isles.

Controlling X-ray beam trajectory with a flexible hollow glass fibre.

PubMed

Tanaka, Yoshihito; Nakatani, Takashi; Onitsuka, Rena; Sawada, Kei; Takahashi, Isao

2014-01-01

A metre-length flexible hollow glass fibre with 20 µm-bore and 1.5 mm-cladding diameters for transporting a synchrotron X-ray beam and controlling the trajectory has been examined. The large cladding diameter maintains a moderate curvature to satisfy the shallow glancing angle of total reflection. The observed transmission efficiency was more than 20% at 12.4 keV. As a demonstration, a wide-area scan of a synchrotron radiation beam was performed to identify the elements for a fixed metal film through its absorption spectra.

Direct and indirect effects of glomalin, mycorrhizal hyphae, and roots on aggregate stability in rhizosphere of trifoliate orange

PubMed Central

Wu, Qiang-Sheng; Cao, Ming-Qin; Zou, Ying-Ning; He, Xin-hua

2014-01-01

To test direct and indirect effects of glomalin, mycorrhizal hyphae, and roots on aggregate stability, perspex pots separated by 37-μm nylon mesh in the middle were used to form root-free hyphae and root/hyphae chambers, where trifoliate orange (Poncirus trifoliata) seedlings were colonized by Funneliformis mosseae or Paraglomus occultum in the root/hyphae chamber. Both fungal species induced significantly higher plant growth, root total length, easily-extractable glomalin-related soil protein (EE-GRSP) and total GRSP (T-GRSP), and mean weight diameter (an aggregate stability indicator). The Pearson correlation showed that root colonization or soil hyphal length significantly positively correlated with EE-GRSP, difficultly-extractable GRSP (DE-GRSP), T-GRSP, and water-stable aggregates in 2.00–4.00, 0.50–1.00, and 0.25–0.50 mm size fractions. The path analysis indicated that in the root/hyphae chamber, aggregate stability derived from a direct effect of root colonization, EE-GRSP or DE-GRSP. Meanwhile, the direct effect was stronger by EE-GRSP or DE-GRSP than by mycorrhizal colonization. In the root-free hyphae chamber, mycorrhizal-mediated aggregate stability was due to total effect but not direct effect of soil hyphal length, EE-GRSP and T-GRSP. Our results suggest that GRSP among these tested factors may be the primary contributor to aggregate stability in the citrus rhizosphere. PMID:25059396

Habitat-dependent interactions between two size-classes of juvenile steelhead in a small stream

Treesearch

Bret C. Harvey; Rodney J. Nakamoto

1997-01-01

Abstract - The presence of small steelhead (Oncorhynchus mykiss; averaging 55 mm fork length) influenced the growth of larger juvenile steelhead (90 mm fork length) during a 6-week experiment conducted in North Fork Caspar Creek, California, in summer 1994. In fenced replicate deep stream sections in this small stream, growth of the larger steelhead was greater in...

7 CFR 51.784 - Classification of defects.

Code of Federal Regulations, 2011 CFR

2011-01-01

... diameter, caused by scale Aggregating more than 1/3 of the surface, caused by scale. Oil spots Aggregating... surface. Sprouting More than six seeds have sprouts of more than 1/4 inch (6.4 mm) in length, or more than 3 seeds with sprouts over 3/4 inch (19.1 mm) in length More than six seeds have sprouts of more than...

[Exploration of three-dimensional biometric measurement of emmetropic adult eye-ball by using magnetic resonance imaging technology].

PubMed

Xu, Hai-Ming; Zhou, Yun-Xin; Shi, Ming-Guang

2008-11-01

To study biometric measurements of emmetropic adult eyes with magnetic resonance imaging technology (MRI). MRI technology, with super-resolution, hyper-speed imaging and the integration of the thin-scanning layer, is applied to measure the three-dimensional biometric parameters of the eyeball. From January to December, 2003, emmetropic eyes from 31 normal Chinese adults (16 males and 15 females) aged from 18 to 32 years old (23.32 +/- 3.32) were successfully measured to obtain the volume of the eyeball and vitreous cavity; inner dimensions of the eye, including the anterior-posterior, vertical and horizontal diameters. The length of ocular axis was measured by A-echo too. Data was analyzed by SPSS 11.0 statistical software. The volume of the eyeball, anterior chamber, lens and the vitreous cavity is (6.013 +/- 0.449) ml, (0.348 +/- 0.020) ml, (0.183 +/- 0.015) ml, and (5.482 +/- 0.440) ml, respectively. The length of anterior-posterior diameter of the vitreous cavity is (16.008 +/- 0.707) mm. The ocular inner dimensions of horizontal, vertical and anterior-posterior planes were (22.455 +/- 0.983) mm, (23.290 +/- 0.815) mm and (22.619 +/- 0.912) mm, respectively. The length of the ocular axis is (23.10 +/- 0.92) mm (with MRI & Orbscan II) and (23.67 +/- 0.82) mm (with A-echo). The value of the ocular length in emmetropic eye measured with both MRI + Orbscan II and the (A-echo) in the present study is very close to the value of the Bennett-Rabbitts schematic eye (24.09 mm). MRI technology is valuable for obtaining more reliable and precise data in the study of ocular physiology and clinical ophthalmology.

Amnion and Chorion Allografts in Combination with Coronally Advanced Flap in the Treatment of Gingival Recession: A Clinical Study

PubMed Central

Chakraborthy, Sonali; Sambashivaiah, Savita; Bilchodmath, Shivaprasad

2015-01-01

Background Guided tissue regeneration (GTR) based root coverage using different allograft membranes has been utilized to correct gingival recession defects with promising results. Amnion and chorion allograft membranes of alternative origin derived from human placental tissue has been advocated in the treatment of gingival recession. However, chorion membrane has been used in combination with amnion membrane no study has compared these allograft membranes in the treatment of gingival recession. Therefore, the purpose of this study was to clinically evaluate and compare the efficacy of amnion membrane and chorion membrane in combination with coronally advanced flap in the treatment of gingival recessions. Materials and Methods Twelve systemically healthy patients having at least 2 bilateral Miller’s Class I or Class II gingival recession were recruited and coronally advanced flap was performed with amnion membrane or chorion membrane. Clinical parameters such as gingival Index, plaque index, length of the recession, width of the recession, width of keratinized gingiva, relative attachment level were evaluated at baseline, 3 and 6 months post-surgery. Results The mean decrease in length of recession (LR) for Chorion site was 2.00±1.54mm and amnion site was 1.58±1.14mm. The gain in attachment level for amnion site was 2.17±1.53mm and for chorion site was 1.58±1.22mm. The total mean percentage of root coverage was 34% for chorion site and 22% for amnion site. Conclusion Both amnion membrane and chorion membrane has shown to be versatile allograft material to be used in the treatment of root coverage. PMID:26501023

A micro-optical system for endoscopy based on mechanical compensation paradigm using miniature piezo-actuation.

PubMed

Cerveri, Pietro; Zazzarini, Cynthia Corinna; Patete, Paolo; Baroni, Guido

2014-06-01

The goal of the study was to investigate the feasibility of a novel miniaturized optical system for endoscopy. Fostering the mechanical compensation paradigm, the modeled optical system, composed by 14 lenses, separated in 4 different sets, had a total length of 15.55mm, an effective focal length ranging from 1.5 to 4.5mm with a zoom factor of about 2.8×, and an angular field of view up to 56°. Predicted maximum lens travel was less than 3.5mm. The consistency of the image plane height across the magnification range testified the zoom capability. The maximum predicted achromatic astigmatism, transverse spherical aberration, longitudinal spherical aberration and relative distortion were less than or equal to 25μm, 15μm, 35μm and 12%, respectively. Tests on tolerances showed that the manufacturing and opto-mechanics mounting are critical as little deviations from design dramatically decrease the optical performances. However, recent micro-fabrication technology can guarantee tolerances close to nominal design. A closed-loop actuation unit, devoted to move the zoom and the focus lens sets, was implemented adopting miniaturized squiggle piezo-motors and magnetic position encoders based on Hall effect. Performance results, using a prototypical test board, showed a positioning accuracy of less than 5μm along a lens travel path of 4.0mm, which was in agreement with the lens set motion features predicted by the analysis. In conclusion, this study demonstrated the feasibility of the optical design and the viability of the actuation approach while tolerances must be carefully taken into account. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Morphological description of Cosmocerca sp. (Nematoda: Cosmocerdidae) from the Mascarene grass frog Ptychadena cf. mascareniensis (Amphibia: Ptychadenidae). A light and scanning electron microscopic studies.

PubMed

Abdel-Gaber, Rewaida; Abdel-Ghaffar, Fathy; Kamel, Reem; Maher, Sherein; El Deeb, Nashwa; Al Quraishy, Saleh; Mehlhorn, Heinz

2017-06-01

The Mascarene grass frog Ptychadena cf. mascareniensis is a species of frog with a vast area of distribution in Africa. A total of 300 frog specimens were collected from different localities at El-Giza province, Egypt; then dissected and examined for the presence of parasitic infection. Only eighty six (28.66%) specimens were found to be naturally infected with nematode parasite. Seasonally, the prevalence of infection was reached its maximum value of 74.66% during summer and minimum values of 26.66% (20/75), 13.33% (10/75) during spring and autumn, respectively; while no records were observed during winter season. The morphology of the recovered parasite was studied by using light and scanning electron microscopy. The adult worm characterized by anterior extremity with small mouth opening being surrounded by three lips provided with four sub-median cephalic papillae and one pair of lateral amphids. Body measurements showed that male worms were smaller than females measuring 1.22-2.43 (2.21 ± 0.1) mm in length and 0.21-0.34 (0.29 ± 0.01) mm in width. Females measured 1.9-3.7 (2.8 ± 0.1) mm in length and 0.24-0.42 (0.38 ± 0.01) mm in width. Comparing the present parasite with other species of the same genus described previously, several similarities were observed. However, peculiar new characteristics such as the arrangement of plectanes and somatic papillae, the presence of gubernaculum, the position of nerve ring, excretory pore, and vulval opening make it reasonable belongs to the family Cosmocercidae and identified as Cosmocerca sp. In addition, the present study was the first report for occurrence of cosmocercid species from the Mascarene grass frog in Egypt.

Ontogenetic development in the morphology and behavior of loach ( Misgurnus anguillicaudatus) during early life stages

NASA Astrophysics Data System (ADS)

Gao, Lei; Duan, Ming; Cheng, Fei; Xie, Songguang

2014-09-01

Loach ( Misgurnus anguillicaudatus) are a commercially important fish in China and an ideal aquaculture species. However, culturists experience high larval and juvenile mortality during mass production. To provide insight into ways to improve larviculture techniques, we describe the morphological characteristics and behavior of loach during the larval and early juvenile stages. Yolksac larvae ranged from 2.8 to 4.0 mm body length (BL) between days 0 to 4; preflexion larvae ranged from 3.6 to 5.5 mm BL between days 4 to 6; flexion larvae ranged from 4.8 to 8.1 mm BL between days 5 and 14; and postflexion larvae ranged from 7.1 to 15.7 mm BL between days 11 to 27; the minimum length and age of juveniles was 14.1 mm BL and 23 d, respectively. Loach are demersal from hatch through to the early juvenile stages. A suite of morphological characteristics (e.g., external gill filament and ventral mouth opening) and behavioral traits have developed to adapt to demersal living. We observed positive allometric growth in eye diameter, head length, head height, and pectoral fin length during the early larval stages, reflecting the priorities in the development of the organs essential for survival. Our results provide a basis for developing techniques to improve the survival of larval and juvenile loach during mass production.

A simple model to demonstrate the electronic apex locator.

PubMed

Tinaz, A C; Alaçam, T; Topuz, O

2002-11-01

To describe and evaluate a newly developed model for demonstrating and teaching the use of electronic apex locators. A phantom model, master jaw model and extracted human teeth were used to construct the demonstration model with alginate impression material as the periapical conductive medium. The model was validated in a series of length determinations with apical foramina enlarged to 0.20, 0.30 and 0.45 mm diameter, and the stability of the model was evaluated up to 45 h after construction. All evaluations were conducted with the Root ZX apex locator with 2.65 and 5.25% NaOCl in the canals. Most length measurements were within 1 mm of actual root length (range: -2.2 to +0.21 mm) and did not change significantly over 45 h for teeth with foramina of 0.3 mm or less. Measurements for teeth with wide (0.45 mm) apices were stable up to 28 h. NaOCl concentration did not significantly affect the readings. A simple, inexpensive model can be manufactured from plastic dental jaws, natural teeth and alginate impression material to demonstrate electronic working length measurement. The model is stable for many hours and provides consistent results with different concentrations of NaOCl in the canal and various apical diameters. The model is a useful teaching aid but needs further evaluation and refinement before use in research applications.

A randomized study to compare bioactive titanium stents and everolimus-eluting stents in diabetic patients (TITANIC XV): 1-year results.

PubMed

López-Mínguez, José R; Nogales-Asensio, Juan M; Doncel-Vecino, Luis J; Merchán-Herrera, Antonio; Pomar-Domingo, Francisco; Martínez-Romero, Pedro; Fernández-Díaz, José A; Valdesuso-Aguilar, Raúl; Moreu-Burgos, José; Díaz-Fernández, José

2014-07-01

Up to 25% of patients who undergo a percutaneous coronary intervention show some limitation in the use of drug-eluting stents. The aim of this study was to evaluate if titanium-nitride-oxide-coated stents could be a good alternative to everolimus-eluting stents in diabetic patients. A total of 173 diabetic patients with lesions at moderate risk of restenosis (exclusion criteria: diameter < 2.5 mm or length > 28 mm in vessels < 3mm, chronic occlusion) were randomized to a titanium group (83 patients) or an everolimus group (90 patients). Baseline characteristics were well balanced; 28.3% of patients were insulin dependent. At 1 year, the incidence of major adverse cardiac events (death, nonfatal myocardial infarction, stroke, or repeat target vessel revascularization) was significantly higher in the titanium group than in the everolimus group (total, 14.5% vs 4.4%; P = .02; noninsulin-dependent subgroup, 9.7% vs 3.2%; P = .14; insulin-dependent subgroup, 28.6% vs 7.1%; P = .04). The incidence of death, nonfatal myocardial infarction, stroke, or any revascularization was 16.9% in the titanium group and 7.8% in the everolimus group (P = .06). Target lesion and vessel revascularizations occurred in 8.4% compared with 3.3% (P = .15) and in 13.3% compared with 3.3% (P = .01) in the titanium and everolimus groups, respectively. Angiographic follow-up at 9 months showed significantly less late lumen loss in the everolimus group (in-segment, 0.52 [standard deviation, 0.58) mm vs -0.05 [0.32] mm; in-stent, 0.76 [0.54] mm vs 0.13 [0.31] mm; P < .0001). The everolimus-eluting stent is superior to the titanium stent for clinical and angiographic end points in diabetic patients with lesions at moderate risk of restenosis. Copyright © 2013 Sociedad Española de Cardiología. Published by Elsevier Espana. All rights reserved.

Influence of corneal power on circumpapillary retinal nerve fiber layer and optic nerve head measurements by spectral-domain optical coherence tomography.

PubMed

Hirasawa, Kazunori; Shoji, Nobuyuki

2017-01-01

To evaluate the influence of corneal power on circumpapillary retinal nerve fiber layer (cpRNFL) and optic nerve head (ONH) measurements by spectral-domain optical coherence tomography (SD-OCT). Twenty-five eyes of 25 healthy participants (mean age 23.6±3.6y) were imaged by SD-OCT using horizontal raster scans. Disposable soft contact lenses of different powers (from -11 to +5 diopters including 0 diopter) were worn to induce 2-diopter changes in corneal power. Differences in the cpRNFL and ONH measurements per diopter of change in corneal power were analyzed. As corneal power increased by 1 diopter, total and quadrant cpRNFL thicknesses, except for the nasal sector, decreased by --0.19 to -0.32 µm ( P <0.01). Furthermore, the disc, cup, and rim areas decreased by -0.017, -0.007, and -0.015 mm 2 , respectively ( P <0.001); the cup and rim volumes decreased by -0.0013 and -0.006 mm 3 , respectively ( P <0.01); and the vertical and horizontal disc diameters decreased by -0.006 and -0.007 mm, respectively ( P <0.001). For more precise OCT imaging, the ocular magnification should be corrected by considering both the axial length and corneal power. However, the effect of corneal power changes on cpRNFL thickness and ONH topography are small when compare with those of the axial length.

SU-F-T-370: A Fast Monte Carlo Dose Engine for Gamma Knife

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, T; Zhou, L; Li, Y

2016-06-15

Purpose: To develop a fast Monte Carlo dose calculation algorithm for Gamma Knife. Methods: To make the simulation more efficient, we implemented the track repeating technique on GPU. We first use EGSnrc to pre-calculate the photon and secondary electron tracks in water from two mono-energy photons of 60Co. The total photon mean free paths for different materials and energies are obtained from NIST. During simulation, each entire photon track was first loaded to shared memory for each block, the incident original photon was then splitted to Nthread sub-photons, each thread transport one sub-photon, the Russian roulette technique was applied formore » scattered and bremsstrahlung photons. The resultant electrons from photon interactions are simulated by repeating the recorded electron tracks. The electron step length is stretched/shrunk proportionally based on the local density and stopping power ratios of the local material. Energy deposition in a voxel is proportional to the fraction of the equivalent step length in that voxel. To evaluate its accuracy, dose deposition in a 300mm*300mm*300mm water phantom is calculated, and compared to EGSnrc results. Results: Both PDD and OAR showed great agreements (within 0.5%) between our dose engine result and the EGSnrc result. It only takes less than 1 min for every simulation, being reduced up to ∼40 times compared to EGSnrc simulations. Conclusion: We have successfully developed a fast Monte Carlo dose engine for Gamma Knife.« less

Percutaneous Retrieval of Foreign Bodies Around Vital Vessels Aided with Vascular Intervention: A Technical Note

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Xiu-Jun, E-mail: woothingyang2008@126.com; Xing, Guang-Fu, E-mail: xgf8848@126.com

ObjectiveTo describe a new interventional technique to remove foreign bodies (FBs) embedded in soft tissues around vital vessels.MethodsUnder fluoroscopic guidance and using local anesthesia, percutaneous removal of FBs was performed using forceps in nine patients. All patients suffered from a metallic soft tissue FB located in close proximity to important vessels and one also had a small traumatic pseudoaneurysm adjacent to the FB. Prior to removal of the FB, the position of the nearest vessel was identified using a guide wire or catheter placed into the vessel. Balloon catheter was also simultaneously used to temporarily stop the blood flow ofmore » the nearest artery during the FB removal in three of the nine patients.ResultsAll of the nine FBs with 0–2 mm interval to the nearest vessel were successfully removed in the nine patients without any serious complications. The removed FBs measured 3–12 mm in length and 1–3 mm in width. The total fluoroscopic time of retrieval of each FB was 5–9 min (mean, 6.4 min). The volume of intraoperative bleeding ranged from 5 to 12 ml (mean, 7.5 ml). The length of hospital stay for each patient ranged from 4 to 8 days (mean, 5.5 days).ConclusionVascular intervention-aided percutaneous FB removal is minimally invasive and an effective method for removal of FBs around vital vessels.« less

Is radiographic measurement of bony landmarks reliable for lateral meniscal sizing?

PubMed

Yoon, Jung-Ro; Kim, Taik-Seon; Lim, Hong-Chul; Lim, Hyung-Tae; Yang, Jae-Hyuk

2011-03-01

The accuracy of meniscal measurement methods is still in debate. The authors' protocol for radiologic measurements will provide reproducible bony landmarks, and this measurement method of the lateral tibial plateau will correlate with the actual anatomic value. Controlled laboratory study. Twenty-five samples of fresh lateral meniscus with attached proximal tibia were obtained during total knee arthroplasty. Each sample was obtained without damage to the meniscus and bony attachment sites. The inclusion criterion was mild to moderate osteoarthritis in patients with mechanical axis deviation of less than 15°. Knees with lateral compartment osteoarthritic change or injured or degenerated menisci were excluded. For the lateral tibial plateau length measurements, the radiographic beam was angled 10° caudally at neutral rotation, which allowed differentiation of the lateral plateau cortical margins from the medial plateau. The transition points were identified and used for length measurement. The values of length were then compared with the conventional Pollard method and the anatomic values. The width measurement was done according to Pollard's protocol. For each knee, the percentage deviation from the anatomic dimension was recorded. Intraobserver error and interobserver error were calculated. The deviation of the authors' radiographic length measurements from anatomic dimensions was 1.4 ± 1.1 mm. The deviation of Pollard's radiographic length measurements was 4.1 ± 2.0 mm. With respect to accuracy-which represents the frequency of measurements that fall within 10% of measurements-the accuracy of authors' length was 98%, whereas for Pollard's method it was 40%. There was a good correlation between anatomic meniscal dimensions and each radiologic plateau dimensions for lateral meniscal width (R(2) = .790) and the authors' lateral meniscal length (R(2) = .823) and fair correlation for Pollard's lateral meniscal length (R(2) = .660). The reliability of each radiologic measurement showed good reliability (intraclass correlation coefficients, .823 to .973). The authors tried to determine the best-fit equation for predicting meniscal size from Pollard's method of bone size, as follows: anatomic length = 0.52 × plateau length (according to Pollard's method) + 5.2, not as Pollard suggested (0.7 × Pollard's plateau length). Based on this equation-namely, the modified Pollard method-the percentage difference decreased, and the accuracy increased to 92%. Lateral meniscal length dimension can be accurately predicted from the authors' radiographic tibial plateau measurements. This study may provide valuable information in preoperative sizing of lateral meniscus in meniscal allograft transplantation.

[Prediction of the latency period by cervical ultrasonography in premature rupture of the membranes before term].

PubMed

Gabriel, R; Morille, C; Drieux, L; Bige, V; Leymarie, F; Quereux, C

2002-11-01

To assess the value of ultrasonographic measurement of cervical length for predicting the duration of the latency period from admission to delivery in women with preterm premature rupture of the membranes (PROM). Prospective study in 88 women with preterm PROM before 34 weeks of amenorrhea. The median gestational age at admission was of 30.1 weeks. The clinical management included: no digital examination of the uterine cervix, antenatal corticosteroids, antibiotics (amoxicillin & clavulanic acid) for 7 days, and hoding back until 34 weeks. Cervical length at admission was determined with transvaginal ultrasonography. The duration of the latency period was studied in relation with cervical length, serum C-reactive protein (CRP) level and white blood cell (WBC) count at admission. The median latency period was longer in women with a cervical length > or = 25 mm (10 vs 5 days; p = 0.04), but this was not associated with a significant increase in birth weight. The median latency period was also longer in women with CRP < 20 mg/l (10 vs 3 days; p < 0.001) and this was associated with a significant increase in birth weight (1716 +/- 549 vs 1201 +/- 485 g; p < 0.01). Moreover, increased CRP levels were more frequent in women with a cervical length < 25 mm, and cervical length was no more predictive of the duration of the latency period in the subgroup of women with CRP < 20 mg/l and WBC < 20,000 cells/mm3. In women with preterm PROM, the latency period from admission to delivery is shorter when cervical length is < 25 mm. However, the clinical value of transvaginal ultrasonography is limited in comparison with serum CRP.

14C/C measurements support Andreev's internode method to determine lichen growth rates in Cladina stygia (Fr.) Ahti

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holt, E; Bench, G

2007-12-05

Growth rates and the ability to date an organism can greatly contribute to understanding its population biology and community dynamics. 1n 1954, Andreev proposed a method to date Cladina, a fruticose lichen, using total thallus length and number of internodes. No research, however, has demonstrated the reliability of this technique or compared its estimates to those derived by other means. In this study, we demonstrate the utility of {sup 14}C/C ratios to determine lichen age and growth rate in Cladina stygia (Fr.) Ahti collected from northwestern Alaska, USA. The average growth rate using {sup 14}C/C ratios was 6.5 mm {center_dot}more » yr{sup -1}, which was not significantly different from growth rates derived by Andreev's internode method (average = 6.2 mm {center_dot} yr{sup -1}); thus, suggesting the reliability of Andreev's simple field method for dating lichens. In addition, we found lichen growth rates appeared to differ with geographic location, yet did not seem related to ambient temperature and total precipitation.« less

Versatile combustion-amalgamation technique for the photometric determination of mercury in fish and environmental samples

USGS Publications Warehouse

Willford, Wayne A.; Hesselberg, Robert J.; Bergman, Harold L.

1973-01-01

Total mercury in a variety of substances is determined rapidly and precisely by direct sample combustion, collection of released mercury by amalgamation, and photometric measurement of mercury volatilized from the heated amalgam. Up to 0.2 g fish tissue is heated in a stream of O2 (1.2 L/min) for 3.5 min in 1 tube of a 2-tube induction furnace. The released mercury vapor and combustion products are carried by the stream of O2 through a series of traps (6% NaOH scrubber, water condenser, and Mg(CIO4)2 drying tube) and the mercury is collected in a 10 mm diameter column of 24 gauge gold wire (8 g) cut into 3 mm lengths. The resulting amalgam is heated in the second tube of the induction furnace and the volatilized mercury is measured with a mercury vapor meter equipped with a recorder-integrator. Total analysis time is approximately 8 min/sample. The detection limit is less than 0.002 μg and the system is easily converted for use with other biological materials, water, and sediments.

49 CFR 587.15 - Verification of aluminum honeycomb crush strength.

Code of Federal Regulations, 2012 CFR

2012-10-01

... material being tested. Four samples, each measuring 300 mm (11.8 in) × 300 mm (11.8 in) × 25 mm (1 in.... Samples of the following size are used for testing. The length is 150 mm (5.9 in) ±6 mm (0.24 in), the width is 150 mm (5.9 in) ±6 mm (0.24 in), and the thickness is 25 mm (1 in) ±2 mm (0.08 in). The walls...

49 CFR 587.15 - Verification of aluminum honeycomb crush strength.

Code of Federal Regulations, 2013 CFR

2013-10-01

... material being tested. Four samples, each measuring 300 mm (11.8 in) × 300 mm (11.8 in) × 25 mm (1 in.... Samples of the following size are used for testing. The length is 150 mm (5.9 in) ±6 mm (0.24 in), the width is 150 mm (5.9 in) ±6 mm (0.24 in), and the thickness is 25 mm (1 in) ±2 mm (0.08 in). The walls...