Performance of spectral MSE diagnostic on C-Mod and ITER

NASA Astrophysics Data System (ADS)

Liao, Ken; Rowan, William; Mumgaard, Robert; Granetz, Robert; Scott, Steve; Marchuk, Oleksandr; Ralchenko, Yuri; Alcator C-Mod Team

2015-11-01

Magnetic field was measured on Alcator C-mod by applying spectral Motional Stark Effect techniques based on line shift (MSE-LS) and line ratio (MSE-LR) to the H-alpha emission spectrum of the diagnostic neutral beam atoms. The high field of Alcator C-mod allows measurements to be made at close to ITER values of Stark splitting (~ Bv⊥) with similar background levels to those expected for ITER. Accurate modeling of the spectrum requires a non-statistical, collisional-radiative analysis of the excited beam population and quadratic and Zeeman corrections to the Stark shift. A detailed synthetic diagnostic was developed and used to estimate the performance of the diagnostic at C-Mod and ITER parameters. Our analysis includes the sensitivity to view and beam geometry, aperture and divergence broadening, magnetic field, pixel size, background noise, and signal levels. Analysis of preliminary experiments agree with Kinetic+(polarization)MSE EFIT within ~2° in pitch angle and simulations predict uncertainties of 20 mT in | B | and <2° in pitch angle. This material is based upon work supported by the U.S. Department of Energy Office of Science, Office of Fusion Energy Sciences under Award Number DE-FG03-96ER-54373 and DE-FC02-99ER54512.

The Addition of SPECT/CT Lymphoscintigraphy to Breast Cancer Radiation Planning Spares Lymph Nodes Critical for Arm Drainage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheville, Andrea L., E-mail: Cheville.andrea@mayo.edu; Brinkmann, Debra H.; Ward, Shelly B.

2013-03-15

Background: This prospective cohort study was designed to determine whether the amount of radiation delivered to the nonpathological lymph nodes (LNs) that drain the arm can be significantly reduced by integrating single-photon emission computed tomography (SPECT)/computed tomography (CT) scans into radiation treatment planning. Methods: SPECT-CT scans were acquired for the 28 patients with stage I or II breast cancer and fused with the routinely obtained radiation oncology planning CT scans. Arm-draining LNs were contoured with 0.5-cm margins automatically using a threshold of 50% maximum intensity. Two treatment plans were generated: 1 per routine clinical practice (standard; STD) and the secondmore » (modified; MOD) with treatment fields modified to minimize dose to the arm-draining LNs visible on SPECT/CT images without interfering with the dosage delivered to target tissues. Participants were treated per the MOD plans. Arm volumes were measured prior to radiation and thereafter at least three subsequent 6-month intervals. Results: Sixty-eight level I-III arm-draining LNs were identified, 57% of which were inside the STD plan fields but could be blocked in the MOD plan fields. Sixty-five percent of arm-draining LNs in the STD versus 16% in the MOD plans received a mean of ≥10 Gy, and 26% in the STD versus 4% in the MOD plans received a mean of ≥40 Gy. Mean LN radiation exposure was 23.6 Gy (standard deviation 18.2) with the STD and 7.7 Gy (standard deviation 11.3) with the MOD plans (P<.001). No participant developed lymphedema. Conclusions: The integration of SPECT/CT scans into breast cancer radiation treatment planning reduces unnecessary arm-draining LN radiation exposure and may lessen the risk of lymphedema.« less

The addition of SPECT/CT lymphoscintigraphy to breast cancer radiation planning spares lymph nodes critical for arm drainage.

PubMed

Cheville, Andrea L; Brinkmann, Debra H; Ward, Shelly B; Durski, Jolanta; Laack, Nadia N; Yan, Elizabeth; Schomberg, Paula J; Garces, Yolanda I; Suman, Vera J; Petersen, Ivy A

2013-03-15

This prospective cohort study was designed to determine whether the amount of radiation delivered to the nonpathological lymph nodes (LNs) that drain the arm can be significantly reduced by integrating single-photon emission computed tomography (SPECT)/computed tomography (CT) scans into radiation treatment planning. SPECT-CT scans were acquired for the 28 patients with stage I or II breast cancer and fused with the routinely obtained radiation oncology planning CT scans. Arm-draining LNs were contoured with 0.5-cm margins automatically using a threshold of 50% maximum intensity. Two treatment plans were generated: 1 per routine clinical practice (standard; STD) and the second (modified; MOD) with treatment fields modified to minimize dose to the arm-draining LNs visible on SPECT/CT images without interfering with the dosage delivered to target tissues. Participants were treated per the MOD plans. Arm volumes were measured prior to radiation and thereafter at least three subsequent 6-month intervals. Sixty-eight level I-III arm-draining LNs were identified, 57% of which were inside the STD plan fields but could be blocked in the MOD plan fields. Sixty-five percent of arm-draining LNs in the STD versus 16% in the MOD plans received a mean of ≥10 Gy, and 26% in the STD versus 4% in the MOD plans received a mean of ≥40 Gy. Mean LN radiation exposure was 23.6 Gy (standard deviation 18.2) with the STD and 7.7 Gy (standard deviation 11.3) with the MOD plans (P<.001). No participant developed lymphedema. The integration of SPECT/CT scans into breast cancer radiation treatment planning reduces unnecessary arm-draining LN radiation exposure and may lessen the risk of lymphedema. Copyright © 2013 Elsevier Inc. All rights reserved.

Diagnostic accuracy of cone-beam computed tomography in detecting secondary caries under composite fillings: an in vitro study.

PubMed

Yildizer Keris, Elif; Demirel, Oguzhan; Ozdede, Melih; Altunkaynak, Bulent; Peker, Ilkay

2017-01-01

The aim of this in vitro study was to assess the diagnostic performance of cone-beam computed tomography (CBCT) in the detection of secondary carious lesions under composite resin fillings applied to different types of cavities. Occlusal cavities (O) (n=18), occlusal cavities with mesial or distal component (MO/DO) (n=30), and mesial-occlusal-distal cavities (MOD) (n=30) were prepared in seventy eight extracted human posterior teeth. In half of the cavities in each group, artificial secondary caries lesions were simulated. All cavities were restored by using composite resin. All specimens were embedded in silicone and they were positioned to have approximal contacts. CBCT imaging was done and data were evaluated two times with two week interval by two observers, using a five-point confidence scale. Intra- and inter-observer agreements were calculated with Kappa statistics (κ). The area under (Az) the receiver operating characteristic (ROC) curve was used to evaluate the diagnostic accuracy. Intra- (κ =0.89) and inter-observer (κ = 0.79) agreements were found to be excellent. Az values were highest for the O restorations which is followed by the MOD and DO/MO restorations. Az values for MOD and DO/MO restorations were very low and no statistically significant difference was found. Sensitivity for DO/MO restorations and specificity for MOD restorations were found to be the lowest values. Diagnostic performance of CBCT was higher in O composite restorations than MOD and DO/MO restorations for secondary caries detection. The use of alternative imaging methods rather than CBCT may be useful for evaluating secondary caries under composite MOD and DO/MO restorations.

MODFLOW-2000, the U.S. Geological Survey modular ground-water model -- Documentation of MOD-PREDICT for predictions, prediction sensitivity analysis, and evaluation of uncertainty

USGS Publications Warehouse

Tonkin, M.J.; Hill, Mary C.; Doherty, John

2003-01-01

This document describes the MOD-PREDICT program, which helps evaluate userdefined sets of observations, prior information, and predictions, using the ground-water model MODFLOW-2000. MOD-PREDICT takes advantage of the existing Observation and Sensitivity Processes (Hill and others, 2000) by initiating runs of MODFLOW-2000 and using the output files produced. The names and formats of the MODFLOW-2000 input files are unchanged, such that full backward compatibility is maintained. A new name file and input files are required for MOD-PREDICT. The performance of MOD-PREDICT has been tested in a variety of applications. Future applications, however, might reveal errors that were not detected in the test simulations. Users are requested to notify the U.S. Geological Survey of any errors found in this document or the computer program using the email address available at the web address below. Updates might occasionally be made to this document, to the MOD-PREDICT program, and to MODFLOW- 2000. Users can check for updates on the Internet at URL http://water.usgs.gov/software/ground water.html/.

MOD-1 Wind Turbine Generator Analysis and Design Report, Volume 2

NASA Technical Reports Server (NTRS)

1979-01-01

The MOD-1 detail design is appended. The supporting analyses presented include a parametric system trade study, a verification of the computer codes used for rotor loads analysis, a metal blade study, and a definition of the design loads at each principal wind turbine generator interface for critical loading conditions. Shipping and assembly requirements, composite blade development, and electrical stability are also discussed.

Deterministic Local Sensitivity Analysis of Augmented Systems - II: Applications to the QUENCH-04 Experiment Using the RELAP5/MOD3.2 Code System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ionescu-Bujor, Mihaela; Jin Xuezhou; Cacuci, Dan G.

2005-09-15

The adjoint sensitivity analysis procedure for augmented systems for application to the RELAP5/MOD3.2 code system is illustrated. Specifically, the adjoint sensitivity model corresponding to the heat structure models in RELAP5/MOD3.2 is derived and subsequently augmented to the two-fluid adjoint sensitivity model (ASM-REL/TF). The end product, called ASM-REL/TFH, comprises the complete adjoint sensitivity model for the coupled fluid dynamics/heat structure packages of the large-scale simulation code RELAP5/MOD3.2. The ASM-REL/TFH model is validated by computing sensitivities to the initial conditions for various time-dependent temperatures in the test bundle of the Quench-04 reactor safety experiment. This experiment simulates the reflooding with water ofmore » uncovered, degraded fuel rods, clad with material (Zircaloy-4) that has the same composition and size as that used in typical pressurized water reactors. The most important response for the Quench-04 experiment is the time evolution of the cladding temperature of heated fuel rods. The ASM-REL/TFH model is subsequently used to perform an illustrative sensitivity analysis of this and other time-dependent temperatures within the bundle. The results computed by using the augmented adjoint sensitivity system, ASM-REL/TFH, highlight the reliability, efficiency, and usefulness of the adjoint sensitivity analysis procedure for computing time-dependent sensitivities.« less

NetMOD Version 2.0 User?s Manual.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J.

2015-10-01

NetMOD ( Net work M onitoring for O ptimal D etection) is a Java-based software package for conducting simulation of seismic, hydracoustic, and infrasonic networks. Specifically, NetMOD simulates the detection capabilities of monitoring networks. Network simulations have long been used to study network resilience to station outages and to determine where additional stations are needed to reduce monitoring thresholds. NetMOD makes use of geophysical models to determine the source characteristics, signal attenuation along the path between the source and station, and the performance and noise properties of the station. These geophysical models are combined to simulate the relative amplitudes ofmore » signal and noise that are observed at each of the stations. From these signal-to-noise ratios (SNR), the probability of detection can be computed given a detection threshold. This manual describes how to configure and operate NetMOD to perform detection simulations. In addition, NetMOD is distributed with simulation datasets for the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) International Monitoring System (IMS) seismic, hydroacoustic, and infrasonic networks for the purpose of demonstrating NetMOD's capabilities and providing user training. The tutorial sections of this manual use this dataset when describing how to perform the steps involved when running a simulation. ACKNOWLEDGEMENTS We would like to thank the reviewers of this document for their contributions.« less

Posttest analysis of LOFT LOCE L2-3 using the ESA RELAP4 blowdown model. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perryman, J.L.; Samuels, T.K.; Cooper, C.H.

A posttest analysis of the blowdown portion of Loss-of-Coolant Experiment (LOCE) L2-3, which was conducted in the Loss-of-Fluid Test (LOFT) facility, was performed using the experiment safety analysis (ESA) RELAP4/MOD5 computer model. Measured experimental parameters were compared with the calculations in order to assess the conservatisms in the ESA RELAP4/MOD5 model.

NetMOD Version 2.0 Parameters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J.

2015-08-01

NetMOD ( Net work M onitoring for O ptimal D etection) is a Java-based software package for conducting simulation of seismic, hydroacoustic and infrasonic networks. Network simulations have long been used to study network resilience to station outages and to determine where additional stations are needed to reduce monitoring thresholds. NetMOD makes use of geophysical models to determine the source characteristics, signal attenuation along the path between the source and station, and the performance and noise properties of the station. These geophysical models are combined to simulate the relative amplitudes of signal and noise that are observed at each ofmore » the stations. From these signal-to-noise ratios (SNR), the probability of detection can be computed given a detection threshold. This document describes the parameters that are used to configure the NetMOD tool and the input and output parameters that make up the simulation definitions.« less

Simulation of German PKL refill/reflood experiment K9A using RELAP4/MOD7. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, M.T.; Davis, C.B.; Behling, S.R.

This paper describes a RELAP4/MOD7 simulation of West Germany's Kraftwerk Union (KWU) Primary Coolant Loop (PKL) refill/reflood experiment K9A. RELAP4/MOD7, a best-estimate computer program for the calculation of thermal and hydraulic phenomena in a nuclear reactor or related system, is the latest version in the RELAP4 code development series. This study was the first major simulation using RELAP4/MOD7 since its release by the Idaho National Engineering Laboratory (INEL). The PKL facility is a reduced scale (1:134) representation of a typical West German four-loop 1300 MW pressurized water reactor (PWR). A prototypical scale of the total volume to power ratio wasmore » maintained. The test facility was designed specifically for an experiment simulating the refill/reflood phase of a Loss-of-Coolant Accident (LOCA).« less

The New Feedback Control System of RFX-mod Based on the MARTe Real-Time Framework

NASA Astrophysics Data System (ADS)

Manduchi, G.; Luchetta, A.; Soppelsa, A.; Taliercio, C.

2014-06-01

A real-time system has been successfully used since 2004 in the RFX-mod nuclear fusion experiment to control the position of the plasma and its Magneto Hydrodynamic (MHD) modes. However, its latency and the limited computation power of the used processors prevented the usage of more aggressive control algorithms. Therefore a new hardware and software architecture has been designed to overcome such limitations and to provide a shorter latency and a much increased computation power. The new system is based on a Linux multi-core server and uses MARTe, a framework for real-time control which is gaining interest in the fusion community.

Conceptual design of the 6 MW Mod-5A wind turbine generator

NASA Technical Reports Server (NTRS)

Barton, R. S.; Lucas, W. C.

1982-01-01

The General Electric Company, Advanced Energy Programs Department, is designing under DOE/NASA sponsorship the MOD-5A wind turbine system which must generate electricity for 3.75 cent/KWH (1980) or less. During the Conceptual Design Phase, completed in March, 1981, the MOD-5A WTG system size and features were established as a result of tradeoff and optimization studies driven by minimizing the system cost of energy (COE). This led to a 400' rotor diameter size. The MOD-5A system which resulted is defined in this paper along with the operational and environmental factors that drive various portions of the design. Development of weight and cost estimating relationships (WCER's) and their use in optimizing the MOD-5A are discussed. The results of major tradeoff studies are also presented. Subsystem COE contributions for the 100th unit are shown along with the method of computation. Detailed descriptions of the major subsystems are given, in order that the results of the various trade and optimization studies can be more readily visualized.

AccessMod 3.0: computing geographic coverage and accessibility to health care services using anisotropic movement of patients

PubMed Central

Ray, Nicolas; Ebener, Steeve

2008-01-01

Background Access to health care can be described along four dimensions: geographic accessibility, availability, financial accessibility and acceptability. Geographic accessibility measures how physically accessible resources are for the population, while availability reflects what resources are available and in what amount. Combining these two types of measure into a single index provides a measure of geographic (or spatial) coverage, which is an important measure for assessing the degree of accessibility of a health care network. Results This paper describes the latest version of AccessMod, an extension to the Geographical Information System ArcView 3.×, and provides an example of application of this tool. AccessMod 3 allows one to compute geographic coverage to health care using terrain information and population distribution. Four major types of analysis are available in AccessMod: (1) modeling the coverage of catchment areas linked to an existing health facility network based on travel time, to provide a measure of physical accessibility to health care; (2) modeling geographic coverage according to the availability of services; (3) projecting the coverage of a scaling-up of an existing network; (4) providing information for cost effectiveness analysis when little information about the existing network is available. In addition to integrating travelling time, population distribution and the population coverage capacity specific to each health facility in the network, AccessMod can incorporate the influence of landscape components (e.g. topography, river and road networks, vegetation) that impact travelling time to and from facilities. Topographical constraints can be taken into account through an anisotropic analysis that considers the direction of movement. We provide an example of the application of AccessMod in the southern part of Malawi that shows the influences of the landscape constraints and of the modes of transportation on geographic coverage. Conclusion By incorporating the demand (population) and the supply (capacities of heath care centers), AccessMod provides a unifying tool to efficiently assess the geographic coverage of a network of health care facilities. This tool should be of particular interest to developing countries that have a relatively good geographic information on population distribution, terrain, and health facility locations. PMID:19087277

JPRS Report, Science & Technology, USSR: Science & Technology Policy

DTIC Science & Technology

1988-04-29

spread: " clusters " of mod- ern science-intensive firms have begun to be grouped around a large university or research center. Such a symbiosis of...Cost Accounting in Scientific Research [G. Lakhtin; PRAVDA, 30 Jan 88] 1 Facilities, Manpower Candidate Members of Ukrainian Academy of Sciences...Ovezgeldyyev; TURKMENSKAYA ISKRA 17 Nov 87] 75 Conversion of Research Organizations to Cost Accounting [A. Guniya; ZARYA VOSTOKA 16 Jan 88] ... 78

Wind turbine generator application places unique demands on tower design and materials

NASA Technical Reports Server (NTRS)

Kita, J. P.

1978-01-01

The most relevant contractual tower design requirements and goal for the Mod-1 tower are related to steel truss tower construction, cost-effective state-of-the-art design, a design life of 30 years, and maximum wind conditions of 120 mph at 30 feet elevation. The Mod-1 tower design approach was an iterative process. Static design loads were calculated and member sizes and overall geometry chosen with the use of finite element computer techniques. Initial tower dynamic characteristics were then combined with the dynamic properties of the other wind turbine components, and a series of complex dynamic computer programs were run to establish a dynamic load set and then a second tower design.

Development tests for the 2.5 megawatt Mod-2 wind turbine generator

NASA Technical Reports Server (NTRS)

Andrews, J. S.; Baskin, J. M.

1982-01-01

The 2.5 megawatt MOD-2 wind turbine generator test program is discussed. The development of the 2.5 megawatt MOD-2 wind turbine generator included an extensive program of testing which encompassed verification of analytical procedures, component development, and integrated system verification. The test program was to assure achievement of the thirty year design operational life of the wind turbine system as well as to minimize costly design modifications which would otherwise have been required during on site system testing. Computer codes were modified, fatigue life of structure and dynamic components were verified, mechanical and electrical component and subsystems were functionally checked and modified where necessary to meet system specifications, and measured dynamic responses of coupled systems confirmed analytical predictions.

NetMOD Version 2.0 Mathematical Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J.; Young, Christopher J.; Chael, Eric P.

2015-08-01

NetMOD ( Net work M onitoring for O ptimal D etection) is a Java-based software package for conducting simulation of seismic, hydroacoustic and infrasonic networks. Network simulations have long been used to study network resilience to station outages and to determine where additional stations are needed to reduce monitoring thresholds. NetMOD makes use of geophysical models to determine the source characteristics, signal attenuation along the path between the source and station, and the performance and noise properties of the station. These geophysical models are combined to simulate the relative amplitudes of signal and noise that are observed at each ofmore » the stations. From these signal-to-noise ratios (SNR), the probabilities of signal detection at each station and event detection across the network of stations can be computed given a detection threshold. The purpose of this document is to clearly and comprehensively present the mathematical framework used by NetMOD, the software package developed by Sandia National Laboratories to assess the monitoring capability of ground-based sensor networks. Many of the NetMOD equations used for simulations are inherited from the NetSim network capability assessment package developed in the late 1980s by SAIC (Sereno et al., 1990).« less

Alcator C-Mod Digital Plasma Control System

NASA Astrophysics Data System (ADS)

Wolfe, S. M.

2005-10-01

A new digital plasma control system (DPCS) has been implemented for Alcator C-Mod. The new system was put into service at the start of the 2005 run campaign and has been in routine operation since. The system consists of two 64-input, 16-output cPCI digitizers attached to a rack-mounted single-CPU Linux server, which performs both the I/O and the computation. During initial operation, the system was set up to directly emulate the original C-Mod ``Hybrid'' MIMO linear control system. Compatibility with the previous control system allows the existing user interface software and data structures to be used with the new hardware. The control program is written in IDL and runs under standard Linux. Interrupts are disabled during the plasma pulses to achieve real-time operation. A synchronous loop is executed with a nominal cycle rate of 10 kHz. Emulation of the original linear control algorithms requires 50 μsec per iteration, with the time evenly split between I/O and computation, so rates of about 20 KHz are achievable. Reliable vertical position control has been demonstrated with cycle rates as low as 5 KHz. Additional computations, including non-linear algorithms and adaptive response, are implemented as optional procedure calls within the main real-time loop.

Considerations for applying VARSKIN mod 2 to skin dose calculations averaged over 10 cm2.

PubMed

Durham, James S

2004-02-01

VARSKIN Mod 2 is a DOS-based computer program that calculates the dose to skin from beta and gamma contamination either directly on skin or on material in contact with skin. The default area for calculating the dose is 1 cm2. Recently, the U.S. Nuclear Regulatory Commission issued new guidelines for calculating shallow dose equivalent from skin contamination that requires the dose be averaged over 10 cm2. VARSKIN Mod 2 was not filly designed to calculate beta or gamma dose estimates averaged over 10 cm2, even though the program allows the user to calculate doses averaged over 10 cm2. This article explains why VARSKIN Mod 2 overestimates the beta dose when applied to 10 cm2 areas, describes a manual method for correcting the overestimate, and explains how to perform reasonable gamma dose calculations averaged over 10 cm2. The article also describes upgrades underway in Varskin 3.

Real-time sensing and gas jet mitigation of VDEs on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Granetz, R. S.; Wolfe, S. M.; Izzo, V. A.; Reinke, M. L.; Terry, J. L.; Hughes, J. W.; Zhurovich, K.; Whyte, D. G.; Bakhtiari, M.; Wurden, G.

2006-10-01

Experiments have been carried out in Alcator C-Mod to test the effectiveness of gas jet disruption mitigation of VDEs with real-time detection and triggering by the C-Mod digital plasma control system (DPCS). The DPCS continuously computes the error in the plasma vertical position from the magnetics diagnostics. When this error exceeds an adjustable preset value, the DPCS triggers the gas jet valve (with a negligible latency time). The high-pressure gas (argon) only takes a few milliseconds to enter the vacuum chamber and begin affecting the plasma, but this is comparable to the VDE timescale on C-Mod. Nevertheless, gas jet injection reduced the halo current, increased the radiated power fraction, and reduced the heating of the divertor compared to unmitigated disruptions, but not quite as well as in earlier mitigation experiments with vertically stable plasmas. Presumably a faster overall response time would be beneficial, and several ways to achieve this will also be discussed.

Test prediction for the German PKL Test K5A using RELAP4/MOD6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Y.S.; Haigh, W.S.; Sullivan, L.H.

RELAP4/MOD6 is the most recent modification in the series of RELAP4 computer programs developed to describe the thermal-hydraulic conditions attendant to postulated transients in light water reactor systems. The major new features in RELAP4/MOD6 include best-estimate pressurized water reactor (PWR) reflood transient analytical models for core heat transfer, local entrainment, and core vapor superheat, and a new set of heat transfer correlations for PWR blowdown and reflood. These new features were used for a test prediction of the Kraftwerk Union three-loop PRIMAR KREISLAUF (PKL) Reflood Test K5A. The results of the prediction were in good agreement with the experimental thermalmore » and hydraulic system data. Comparisons include heater rod surface temperature, system pressure, mass flow rates, and core mixture level. It is concluded that RELAP4/MOD6 is capable of accurately predicting transient reflood phenomena in the 200% cold-leg break test configuration of the PKL reflood facility.« less

Dynamic Algorithms for Transition Matrix Generation

NASA Astrophysics Data System (ADS)

Yevick, David; Lee, Yong Hwan

The methods of [D. Yevick, Int. J. Mod. Phys. C, 1650041] for constructing transition matrices are applied to the two dimensional Ising model. Decreasing the system temperature during the acquisition of the matrix elements yields a reasonably precise specific heat curve for a 32x32 spin system for a limited number (50-100M) of realizations. If the system is instead evolved to first higher and then lower energies within a restricted interval that is steadily displaced in energy as the computation proceeds, a modification which permits backward displacements up to a certain lower bound for each forward step ensures acceptable accuracy. Additional constraints on the transition rule are also investigated. The Natural Sciences and Engineering Research Council of Canada (NSERC) and CIENA are acknowledged for financial support.

Posttest analysis of international standard problem 10 using RELAP4/MOD7. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, M.; Davis, C.B.; Peterson, A.C. Jr.

RELAP4/MOD7, a best estimate computer code for the calculation of thermal and hydraulic phenomena in a nuclear reactor or related system, is the latest version in the RELAP4 code development series. This paper evaluates the capability of RELAP4/MOD7 to calculate refill/reflood phenomena. This evaluation uses the data of International Standard Problem 10, which is based on West Germany's KWU PKL refill/reflood experiment K9A. The PKL test facility represents a typical West German four-loop, 1300 MW pressurized water reactor (PWR) in reduced scale while maintaining prototypical volume-to-power ratio. The PKL facility was designed to specifically simulate the refill/reflood phase of amore » hypothetical loss-of-coolant accident (LOCA).« less

A Computer Model for Red Blood Cell Chemistry

DTIC Science & Technology

1996-10-01

5012. 13. ABSTRACT (Maximum 200 There is a growing need for interactive computational tools for medical education and research. The most exciting...paradigm for interactive education is simulation. Fluid Mod is a simulation based computational tool developed in the late sixties and early seventies at...to a modern Windows, object oriented interface. This development will provide students with a useful computational tool for learning . More important

Mortality indicators and risk factors for intra-abdominal hypertension in severe acute pancreatitis.

PubMed

Zhao, J G; Liao, Q; Zhao, Y P; Hu, Y

2014-01-01

This study assessed the risk factors associated with mortality and the development of intra-abdominal hypertension (IAH) in patients with severe acute pancreatitis (SAP). To identify significant risk factors, we assessed the following variables in 102 patients with SAP: age, gender, etiology, serum amylase level, white blood cell (WBC) count, serum calcium level, Acute Physiology and Chronic Health Evaluation II (APACHE-II) score, computed tomography severity index (CTSI) score, pancreatic necrosis, surgical interventions, and multiple organ dysfunction syndrome (MODS). Statistically significant differences were identified using the Student t test and the χ (2) test. Independent risk factors for survival were analyzed by Cox proportional hazards regression. The following variables were significantly related to both mortality and IAH: WBC count, serum calcium level, serum amylase level, APACHE-II score, CTSI score, pancreatic necrosis, pancreatic necrosis >50%, and MODS. However, it was found that surgical intervention had no significant association with mortality. MODS and pancreatic necrosis >50% were found to be independent risk factors for survival in patients with SAP. Mortality and IAH from SAP were significantly related to WBC count, serum calcium level, serum amylase level, APACHE-II score, CTSI score, pancreatic necrosis, and MODS. However, Surgical intervention did not result in higher mortality. Moreover, MODS and pancreatic necrosis >50% predicted a worse prognosis in SAP patients.

Estimating Per-Pixel GPP of the Contiguous USA Directly from MODIS EVI Data

NASA Astrophysics Data System (ADS)

Rahman, A. F.; Sims, D. A.; El-Masri, B. Z.; Cordova, V. D.

2005-12-01

We estimated gross primary production (GPP) of the contiguous USA using enhanced vegetation index (EVI) data from NASA's moderate resolution imaging spectroradiometer (MODIS). Based on recently published values of correlation coefficients between EVI and GPP of North American vegetations, we derived GPP maps of the contiguous USA for 2001-2004, which included one La Nina year and three moderately El Nino years. The product was a truly per-pixel GPP estimate (named E-GPP), in contrast to the pseudo-continuous MOD17, the standard MODIS GPP product. We compared E-GPP with fine-scale experimental GPP data and MOD17 estimates from three Bigfoot experimental sites, and also with MOD17 estimates from the whole contiguous USA for the above-mentioned four years. For each of the '7 by 7' km Bigfoot experimental sites, E-GPP was able to track the primary production activity during the green-up period while MOD17 failed to do so. The E-GPP estimates during peak production season were similar to those from Bigfoot and MOD17 for most vegetation types except for the deciduous types, where it was lower. Annual E-GPP of the Bigfoot sites compared well with Bigfoot experimental GPP (r = 0.71) and MOD17 (r = 0.78). But for the contiguous USA for 2001-2004, annual E-GPP showed disagreement with MOD17 in both magnitude and seasonal trends for deciduous forests and grass lands. In this study we explored the reasons for this mismatch between E-GPP and MOD17 and also analyzed the uncertainties in E-GPP across multiple spatial scales. Our results show that the E-GPP, based on a simple regression model, can work as a robust alternative to MOD17 for large-area annual GPP estimation. The relative advantages of E-GPP are that it is truly per-pixel, solely dependent on remotely sensed data that is routinely available from NASA, easy to compute and has the potential of being used as an operational product.

Posttest calculation of the PBF LOC-11B and LOC-11C experiments using RELAP4/MOD6. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendrix, C.E.

Comparisons between RELAP4/MOD6, Update 4 code-calculated and measured experimental data are presented for the PBF LOC-11C and LOC-11B experiments. Independent code verification techniques are now being developed and this study represents a preliminary effort applying structured criteria for developing computer models, selecting code input, and performing base-run analyses. Where deficiencies are indicated in the base-case representation of the experiment, methods of code and criteria improvement are developed and appropriate recommendations are made.

Fast parallel DNA-based algorithms for molecular computation: quadratic congruence and factoring integers.

PubMed

Chang, Weng-Long

2012-03-01

Assume that n is a positive integer. If there is an integer such that M (2) ≡ C (mod n), i.e., the congruence has a solution, then C is said to be a quadratic congruence (mod n). If the congruence does not have a solution, then C is said to be a quadratic noncongruence (mod n). The task of solving the problem is central to many important applications, the most obvious being cryptography. In this article, we describe a DNA-based algorithm for solving quadratic congruence and factoring integers. In additional to this novel contribution, we also show the utility of our encoding scheme, and of the algorithm's submodules. We demonstrate how a variety of arithmetic, shifted and comparative operations, namely bitwise and full addition, subtraction, left shifter and comparison perhaps are performed using strands of DNA.

Process for selecting NEAMS applications for access to Idaho National Laboratory high performance computing resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael Pernice

2010-09-01

INL has agreed to provide participants in the Nuclear Energy Advanced Mod- eling and Simulation (NEAMS) program with access to its high performance computing (HPC) resources under sponsorship of the Enabling Computational Technologies (ECT) program element. This report documents the process used to select applications and the software stack in place at INL.

Piloting and Evaluating a Workshop to Teach Georgia Teachers about Weather Science and Safety

ERIC Educational Resources Information Center

Stewart, Alan E.; Knox, John A.; Schneider, Pat

2015-01-01

A survey of 691 Georgia teachers suggested that their students generally were not prepared for severe weather. Teachers also were somewhat dissatisfied with the quality of the teaching resources on weather and weather safety. Only 46 (7%) of the teachers were aware of the American Red Cross Masters of Disaster (MoD) weather science and safety…

PREFACE: Modern Technologies in Industrial Engineering (ModTech2015)

NASA Astrophysics Data System (ADS)

Oanta, E.; Comaneci, R.; Carausu, C.; Placzek, M.; Cohal, V.; Topala, P.; Nedelcu, D.

2015-11-01

The dominant feature of the current stage of society development is the update, refinement and innovation of the technological processes and products whose ultimate goal is to satisfy the market requirements. New and modern technologies should be considered in terms of their applicability in industry while the materials can lead to an increase in the quality of the end products. Replacing the existing technologies with innovative and eco-efficient technologies can contribute to an added value increase in the production of new materials. Materials are one of the most dynamic and prospective fields, with applications in all other fields. The development of new advanced materials and technologies shall contribute to the procurement of a wide range of reliable products, with competitive prices and worldwide performance, high sensitivity and functionality, user-friendly and reduced energy consumption, for different industrial applications. Research in the field of advanced/intelligent materials supposes a fundamental, experimental, laboratory and technological research and its approach has to be linked to the application. This involves, even for the niche fields, complex projects which result in scientific issues in top journals, patents and functional models. The third edition of ModTech International Conference was held in Mamaia, Romania, between June 17-20, with the Professional Association in Modern Manufacturing Technologies, ModTech, as main organizer, and the Constanta Maritime University, Constanta, Romania, Silesian University of Technology, Gliwice, Poland, the Technical University of Chisinau, Republic of Moldova and the Donetsk National Technical University, Donetsk, Ukraine as co-organizers. The ModTech2015 International Conference brought together representatives of technology and materials manufacturers, various universities, professional associations and research institutes that exchanged the latest knowledge on the conference topics. This edition was attended by 140 participants from 17 countries. The authors and co-authors were from various countries worldwide, namely: Sweden, China, Switzerland, Romania, Serbia, Germany, Netherlands, Belgium, France, South Korea, Taiwan, Poland, USA, Slovenia, Turkey, Republic of Moldova, Russia, Finland, Japan, Ukraine, Portugal, Uzbekistan, Iraq, Italy and India. The Keynote Speakers were as follows: Prof. Esteban Broitman - Linkoping University, Sweden; Prof. Ziyi Ge - NIMTE, Chinese Academy of Sciences, Ningbo, China; Prof. Thomas Graule - EMPA, Switzerland; prof. Razvan Tamas - Constanta Maritime University, Romania; Prof. Rainer Gadow - University of Stuttgart, Germany; Prof. Marcel Van de Voorde - DELFT University of Technology, Netherlands; Prof. Chris Lacor - Vrije University, Brussels, Belgium; Prof. Fiqiri Hodaj - National Polytechnique Institute of Grenoble, France; Prof. Hong Seok Park - University of Ulsan, South Korea; Prof. Der-Jang Liaw - National Taiwan University of Science and Technology, Taiwan; Prof. Petrica Vizureanu - Gheorghe Asachi Technical University of Iasi, Romania. The main publications of ModTech2015 International Conference are as follows: IOP Conference Series: Materials Science and Engineering, United Kingdom, Indian Journal of Engineering & Materials Sciences (IJEMS) and International Journal of Modern Manufacturing Technologies (IJMMT).

Anomalous transport in the H-mode pedestal of Alcator C-Mod discharges

NASA Astrophysics Data System (ADS)

Pankin, A. Y.; Hughes, J. W.; Greenwald, M. J.; Kritz, A. H.; Rafiq, T.

2017-02-01

Anomalous transport in the H-mode pedestal region of five Alcator C-Mod discharges, representing a collisionality scan is analyzed. The understanding of anomalous transport in the pedestal region is important for the development of a comprehensive model for the H-mode pedestal slope. In this research, a possible role of the drift resistive inertial ballooning modes (Rafiq et al 2010 Phys. Plasmas 17 082511) in the edge of Alcator C-Mod discharges is analyzed. The stability analysis, carried out using the TRANSP code, indicates that the DRIBM modes are strongly unstable in Alcator C-Mod discharges with large electron collisionality. An improved interpretive analysis of H-mode pedestal experimental data is carried out utilizing the additive flux minimization technique (Pankin et al 2013 Phys. Plasmas 20 102501) together with the guiding-center neoclassical kinetic XGC0 code. The neoclassical and neutral physics are simulated in the XGC0 code and the anomalous fluxes are computed using the additive flux minimization technique. The anomalous fluxes are reconstructed and compared with each other for the collisionality scan Alcator C-Mod discharges. It is found that the electron thermal anomalous diffusivities at the pedestal top increase with the electron collisionality. This dependence can also point to the drift resistive inertial ballooning modes as the modes that drive the anomalous transport in the plasma edge of highly collisional discharges.

Analysis of steam generator loss-of-feedwater experiments with APROS and RELAP5/MOD3.1 computer codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Virtanen, E.; Haapalehto, T.; Kouhia, J.

1995-09-01

Three experiments were conducted to study the behavior of the new horizontal steam generator construction of the PACTEL test facility. In the experiments the secondary side coolant level was reduced stepwise. The experiments were calculated with two computer codes RELAP5/MOD3.1 and APROS version 2.11. A similar nodalization scheme was used for both codes to that the results may be compared. Only the steam generator was modelled and the rest of the facility was given as a boundary condition. The results show that both codes calculate well the behaviour of the primary side of the steam generator. On the secondary sidemore » both codes calculate lower steam temperatures in the upper part of the heat exchange tube bundle than was measured in the experiments.« less

Army Science and Technology Master Plan, Fiscal Year 1997 - Volume 2.

DTIC Science & Technology

1996-12-01

areas. Microbiology, physiology, and pharmacology are essential sciences in the production of fermented and processed foods (bread, yogurt , beer, wine...engineering) are of significant interest to the U.S. Army, and include production of the material (including cell culture and fermentation ), downstream...remains strong in targeted delivery (associated with MOD laboratories). Hungary has an established capability in production of fermenters . Remediation

An overview and the current status of instrumentation at the Large Binocular Telescope Observatory

NASA Astrophysics Data System (ADS)

Wagner, R. Mark; Edwards, Michelle L.; Kuhn, Olga; Thompson, David; Veillet, Christian

2014-07-01

An overview of instrumentation for the Large Binocular Telescope (LBT) is presented. Optical instrumentation includes the Large Binocular Camera (LBC), a pair of wide-field (24' × 24') mosaic CCD imagers at the prime focus, and the Multi-Object Double Spectrograph (MODS), a pair of dual-beam blue-red optimized long-slit spectrographs mounted at the left and right direct F/15 Gregorian foci incorporating multiple slit masks for multi-object spectroscopy over a 6' field and spectral resolutions of up to 2000. Infrared instrumentation includes the LBT Near-IR Spectrometer (LUCI), a modular near-infrared (0.9-2.5 μm) imager and spectrograph pair mounted at the left and right front-bent F/15 Gregorian foci and designed for seeing-limited (FOV: 4' × 4') imaging, long-slit spectroscopy, and multi-object spectroscopy utilizing cooled slit masks and diffraction limited (FOV: 0'.5 x 0'.5) imaging and long-slit spectroscopy. Strategic instruments under development that can utilize the full 23 m baseline of the LBT include an interferometric cryogenic beam combiner with near-infrared and thermal-infrared instruments for Fizeau imaging and nulling interferometry (LBTI) and an optical bench near- infrared beam combiner utilizing multi-conjugate adaptive optics for high angular resolution and sensitivity (LINC-NIRVANA). LBTI is currently undergoing commissioning and performing science observations on the LBT utilizing the installed adaptive secondary mirrors in both single-sided and two-sided beam combination modes. In addition, a fiber-fed bench spectrograph (PEPSI) capable of ultra high resolution spectroscopy and spectropolarimetry (R = 40,000-300,000) will be available as a principal investigator instrument. Installation and testing of the bench spectrograph will begin in July 2014. Over the past four years the LBC pair, LUCI1, and MODS1 have been commissioned and are now scheduled for routine partner science observations. Both LUCI2 and MODS2 passed their laboratory acceptance milestones in the summer of 2013 and have been installed on the LBT. LUCI2 is currently being commissioned and the data analysis is well underway. Diffraction-limited commissioning of its adaptive optics modes will begin in the 2014B semester. MODS2 commissioning began in May 2014 and will completed in the 2014B semester as well. Binocular testing and commissioning of both the LUCI and MODS pairs will begin in 2014B with the goal that this capability could be offered sometime in 2015. The availability of all these instruments mounted simultaneously on the LBT permits unique science, flexible scheduling, and improved operational support.

Computational and Statistical Models: A Comparison for Policy Modeling of Childhood Obesity

NASA Astrophysics Data System (ADS)

Mabry, Patricia L.; Hammond, Ross; Ip, Edward Hak-Sing; Huang, Terry T.-K.

As systems science methodologies have begun to emerge as a set of innovative approaches to address complex problems in behavioral, social science, and public health research, some apparent conflicts with traditional statistical methodologies for public health have arisen. Computational modeling is an approach set in context that integrates diverse sources of data to test the plausibility of working hypotheses and to elicit novel ones. Statistical models are reductionist approaches geared towards proving the null hypothesis. While these two approaches may seem contrary to each other, we propose that they are in fact complementary and can be used jointly to advance solutions to complex problems. Outputs from statistical models can be fed into computational models, and outputs from computational models can lead to further empirical data collection and statistical models. Together, this presents an iterative process that refines the models and contributes to a greater understanding of the problem and its potential solutions. The purpose of this panel is to foster communication and understanding between statistical and computational modelers. Our goal is to shed light on the differences between the approaches and convey what kinds of research inquiries each one is best for addressing and how they can serve complementary (and synergistic) roles in the research process, to mutual benefit. For each approach the panel will cover the relevant "assumptions" and how the differences in what is assumed can foster misunderstandings. The interpretations of the results from each approach will be compared and contrasted and the limitations for each approach will be delineated. We will use illustrative examples from CompMod, the Comparative Modeling Network for Childhood Obesity Policy. The panel will also incorporate interactive discussions with the audience on the issues raised here.

Snow fraction products evaluation with Landsat-8/OLI data and its spatial scale effects over the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Jiang, L.

2016-12-01

Snow cover is one of important elements in the water supply of large populations, especially in those downstream from mountainous watershed. The cryosphere process in the Tibetan Plateau is paid much attention due to rapid change of snow amount and cover extent. Snow mapping from MODIS has been increased attention in the study of climate change and hydrology. But the lack of intensive validation of different snow mapping methods especially at Tibetan Plateau hinders its application. In this work, we examined three MODIS snow products, including standard MODIS fractional snow product (MOD10A1) (Kaufman et al., 2002; Salomonson & Appel, 2004, 2006), two other fractional snow product, MODSCAG (Painter et al., 2009) and MOD_MESMA (Shi, 2012). Both these two methods are based on spectral mixture analysis. The difference between MODISCAG and MOD_MESMA was the endmember selection. For MODSCAG product, snow spectral endmembers of varying grain size was obtained both from a radiative transfer model and spectra of vegetation, rock and soil collected in the field and laboratory. MOD_MESMA was obtained from automated endmember extraction method using linear spectral mixture analysis. Its endmembers are selected in each image to enhance the computational efficiency of MESMA (Multiple Endmember Spectral Analysis). Landsat-8 Operatinal Land Imager (OLI) data from 2013-2015 was used to evaluate the performance of these three snow fraction products in Tibetan Plateau. The effect of land cover types including forest, grass and bare soil was analyzed to evaluate three products. In addition, the effects of relatively flat surface in internal plateau and high mountain areas of Himalaya were also evaluated on the impact of these snow fraction products. From our comparison, MODSCAG and MOD10A1 overestimated snow cover, while MOD_MESMA underestimated snow cover. And RMSE of MOD_MESMA at each land cover type including forest, grass and mountain area decreased with the spatial resolution increasing from 500m, 1km, 2km to 5km. The RMSE of MODSCAG and MOD10A1 is very similar. In Himalaya area, these two RMSEs of MODSCAG and MOD10A1 increased with the spatial resolution increasing from 500m to 5km. For forest, grass and bare soil, RMSE decreased from 500m to 1km, then increased from 1km to 2km.

[Diagnostic value of integral scoring systems in assessing the severity of acute pancreatitis and patient's condition].

PubMed

Vinnik, Y S; Dunaevskaya, S S; Antufrieva, D A

2015-01-01

The aim of the study was to evaluate the diagnostic value of specific and nonspecific scoring systems Tolstoy-Krasnogorov score, Ranson, BISAP, Glasgow, MODS 2, APACHE II and CTSI, which used at urgent pancreatology for estimation the severity of acute pancreatitis and status of patient. 1550 case reports of patients which had inpatient surgical treatment at Road clinical hospital at the station Krasnoyarsk from 2009 till 2013 were analyzed. Diagnosis of severe acute pancreatitis and its complications were determined based on anamnestic data, physical exami- nation, clinical indexes, ultrasonic examination and computed tomography angiography. Specific and nonspecific scores (scoring system of estimation by Tolstoy-Krasnogorov, Ranson, Glasgow, BISAP, MODS 2, APACHE II, CTSI) were used for estimation the severity of acute pancreatitis and patient's general condition. Effectiveness of these scoring systems was determined based on some parameters: accuracy (Ac), sensitivity (Se), specificity (Sp), positive predictive value (PPV) and negative predictive value (NPV). Most valuables score for estimation of acute pancreatitis's severity is BISAP (Se--98.10%), for estimation of organ failure--MODS 2 (Sp--100%, PPV--100%) and APACHE II (Sp--100%, PPV--100%), for detection of pancreatonecrosis sings--CTSI (Sp--100%, NPV--100%), for estimation of need for intensive care--MODS 2 (Sp--100%, PPV--100%, NPV--96.29%) and APACHE II (Sp--100%, PPV--100%, NPV--97.21%), for prediction of lethality--MODS 2 (Se-- 100%, Sp--98.14%, NPV--100%) and APACHE II (Se--95.00%, NPV-.99.86%). Most effective scores for estimation of acute pancreatitis's severity are Score of estimation by Tolstoy-Krasnogorov, Ranson, Glasgow and BISAP Scoring systems MODS 2, APACHE I high specificity and positive predictive value allow using it at clinical practice.

Evaluating the role of land cover and climate uncertainties in computing gross primary production in Hawaiian Island ecosystems

PubMed Central

Selmants, Paul C.; Moreno, Alvaro; Running, Steve W.; Giardina, Christian P.

2017-01-01

Gross primary production (GPP) is the Earth’s largest carbon flux into the terrestrial biosphere and plays a critical role in regulating atmospheric chemistry and global climate. The Moderate Resolution Imaging Spectrometer (MODIS)-MOD17 data product is a widely used remote sensing-based model that provides global estimates of spatiotemporal trends in GPP. When the MOD17 algorithm is applied to regional scale heterogeneous landscapes, input data from coarse resolution land cover and climate products may increase uncertainty in GPP estimates, especially in high productivity tropical ecosystems. We examined the influence of using locally specific land cover and high-resolution local climate input data on MOD17 estimates of GPP for the State of Hawaii, a heterogeneous and discontinuous tropical landscape. Replacing the global land cover data input product (MOD12Q1) with Hawaii-specific land cover data reduced statewide GPP estimates by ~8%, primarily because the Hawaii-specific land cover map had less vegetated land area compared to the global land cover product. Replacing coarse resolution GMAO climate data with Hawaii-specific high-resolution climate data also reduced statewide GPP estimates by ~8% because of the higher spatial variability of photosynthetically active radiation (PAR) in the Hawaii-specific climate data. The combined use of both Hawaii-specific land cover and high-resolution Hawaii climate data inputs reduced statewide GPP by ~16%, suggesting equal and independent influence on MOD17 GPP estimates. Our sensitivity analyses within a heterogeneous tropical landscape suggest that refined global land cover and climate data sets may contribute to an enhanced MOD17 product at a variety of spatial scales. PMID:28886187

Evaluating the role of land cover and climate uncertainties in computing gross primary production in Hawaiian Island ecosystems

USGS Publications Warehouse

Kimball, Heather L.; Selmants, Paul; Moreno, Alvaro; Running Steve W,; Giardina, Christian P.

2017-01-01

Gross primary production (GPP) is the Earth’s largest carbon flux into the terrestrial biosphere and plays a critical role in regulating atmospheric chemistry and global climate. The Moderate Resolution Imaging Spectrometer (MODIS)-MOD17 data product is a widely used remote sensing-based model that provides global estimates of spatiotemporal trends in GPP. When the MOD17 algorithm is applied to regional scale heterogeneous landscapes, input data from coarse resolution land cover and climate products may increase uncertainty in GPP estimates, especially in high productivity tropical ecosystems. We examined the influence of using locally specific land cover and high-resolution local climate input data on MOD17 estimates of GPP for the State of Hawaii, a heterogeneous and discontinuous tropical landscape. Replacing the global land cover data input product (MOD12Q1) with Hawaii-specific land cover data reduced statewide GPP estimates by ~8%, primarily because the Hawaii-specific land cover map had less vegetated land area compared to the global land cover product. Replacing coarse resolution GMAO climate data with Hawaii-specific high-resolution climate data also reduced statewide GPP estimates by ~8% because of the higher spatial variability of photosynthetically active radiation (PAR) in the Hawaii-specific climate data. The combined use of both Hawaii-specific land cover and high-resolution Hawaii climate data inputs reduced statewide GPP by ~16%, suggesting equal and independent influence on MOD17 GPP estimates. Our sensitivity analyses within a heterogeneous tropical landscape suggest that refined global land cover and climate data sets may contribute to an enhanced MOD17 product at a variety of spatial scales.

Evaluating the role of land cover and climate uncertainties in computing gross primary production in Hawaiian Island ecosystems.

PubMed

Kimball, Heather L; Selmants, Paul C; Moreno, Alvaro; Running, Steve W; Giardina, Christian P

2017-01-01

Gross primary production (GPP) is the Earth's largest carbon flux into the terrestrial biosphere and plays a critical role in regulating atmospheric chemistry and global climate. The Moderate Resolution Imaging Spectrometer (MODIS)-MOD17 data product is a widely used remote sensing-based model that provides global estimates of spatiotemporal trends in GPP. When the MOD17 algorithm is applied to regional scale heterogeneous landscapes, input data from coarse resolution land cover and climate products may increase uncertainty in GPP estimates, especially in high productivity tropical ecosystems. We examined the influence of using locally specific land cover and high-resolution local climate input data on MOD17 estimates of GPP for the State of Hawaii, a heterogeneous and discontinuous tropical landscape. Replacing the global land cover data input product (MOD12Q1) with Hawaii-specific land cover data reduced statewide GPP estimates by ~8%, primarily because the Hawaii-specific land cover map had less vegetated land area compared to the global land cover product. Replacing coarse resolution GMAO climate data with Hawaii-specific high-resolution climate data also reduced statewide GPP estimates by ~8% because of the higher spatial variability of photosynthetically active radiation (PAR) in the Hawaii-specific climate data. The combined use of both Hawaii-specific land cover and high-resolution Hawaii climate data inputs reduced statewide GPP by ~16%, suggesting equal and independent influence on MOD17 GPP estimates. Our sensitivity analyses within a heterogeneous tropical landscape suggest that refined global land cover and climate data sets may contribute to an enhanced MOD17 product at a variety of spatial scales.

An inverse modeling strategy and a computer program to model garnet growth and resorption

NASA Astrophysics Data System (ADS)

Lanari, Pierre; Giuntoli, Francesco

2017-04-01

GrtMod is a computer program that allows numerical simulation of the pressure-temperature (P-T) evolution of garnet porphyroblasts based on the composition of successive growth zones preserved in natural samples. For each garnet growth stage, a new reactive bulk composition is optimized, allowing for resorption and/or fractionation of the previously crystalized garnet. The successive minimizations are performed using a heuristic search method and an objective function that quantify the amount by which the predicted garnet composition deviates from the measured values. The automated strategy of GrtMod includes a two stages optimization and one refinement stage. In this contribution, we will present several application examples. The new strategy provides quantitative estimates of the optimal P-T conditions whereas it was generally derived in a qualitatively way by using garnet isopleth intersections in equilibrium phase diagrams. GrtMod can also be used to model the evolution of the reactive bulk composition along any P-T trajectories. The results for typical MORB and metapelite compositions demonstrate that fractional crystallization models are required to derive accurate P-T information from garnet compositional zoning. GrtMod can also be used to retrieve complex garnet histories involving several stages of resorption. For instance, it has been used to model the P-T condition of garnet growth in grains from the Sesia Zone (Western Alps). The compositional variability of successive growth zones is characterized using standardized X-ray maps and the program XMapTools. Permian garnet cores crystalized under granulite facies conditions (T > 800°C and P = 6 kbar), whereas Alpine garnet rims grew at eclogite facies conditions (650°C and 16 kbar) involving several successive episodes of resorption. The model predicts that up to 50 vol% of garnet was dissolved before a new episode of garnet growth.

Mod3DMT and EMTF: Free Software for MT Data Processing and Inversion

NASA Astrophysics Data System (ADS)

Egbert, G. D.; Kelbert, A.; Meqbel, N. M.

2017-12-01

"ModEM" was developed at Oregon State University as a modular system for inversion of electromagnetic (EM) geophysical data (Egbert and Kelbert, 2012; Kelbert et al., 2014). Although designed for more general (frequency domain) EM applications, and originally intended as a testbed for exploring inversion search and regularization strategies, our own initial uses of ModEM were for 3-D imaging of the deep crust and upper mantle at large scales. Since 2013 we have offered a version of the source code suitable for 3D magnetotelluric (MT) inversion on an "as is, user beware" basis for free for non-commercial applications. This version, which we refer to as Mod3DMT, has since been widely used by the international MT community. Over 250 users have registered to download the source code, and at least 50 MT studies in the refereed literature, covering locations around the globe at a range of spatial scales, cite use of ModEM for 3D inversion. For over 30 years I have also made MT processing software available for free use. In this presentation, I will discuss my experience with these freely available (but perhaps not truly open-source) computer codes. Although users are allowed to make modifications to the codes (on conditions that they provide a copy of the modified version) only a handful of users have tried to make any modification, and only rarely are modifications even reported, much less provided back to the developers.

Watershed Modeling Applications with the Open-Access Modular Distributed Watershed Educational Toolbox (MOD-WET) and Introductory Hydrology Textbook

NASA Astrophysics Data System (ADS)

Huning, L. S.; Margulis, S. A.

2014-12-01

Traditionally, introductory hydrology courses focus on hydrologic processes as independent or semi-independent concepts that are ultimately integrated into a watershed model near the end of the term. When an "off-the-shelf" watershed model is introduced in the curriculum, this approach can result in a potential disconnect between process-based hydrology and the inherent interconnectivity of processes within the water cycle. In order to curb this and reduce the learning curve associated with applying hydrologic concepts to complex real-world problems, we developed the open-access Modular Distributed Watershed Educational Toolbox (MOD-WET). The user-friendly, MATLAB-based toolbox contains the same physical equations for hydrological processes (i.e. precipitation, snow, radiation, evaporation, unsaturated flow, infiltration, groundwater, and runoff) that are presented in the companion e-textbook (http://aqua.seas.ucla.edu/margulis_intro_to_hydro_textbook.html) and taught in the classroom. The modular toolbox functions can be used by students to study individual hydrologic processes. These functions are integrated together to form a simple spatially-distributed watershed model, which reinforces a holistic understanding of how hydrologic processes are interconnected and modeled. Therefore when watershed modeling is introduced, students are already familiar with the fundamental building blocks that have been unified in the MOD-WET model. Extensive effort has been placed on the development of a highly modular and well-documented code that can be run on a personal computer within the commonly-used MATLAB environment. MOD-WET was designed to: 1) increase the qualitative and quantitative understanding of hydrological processes at the basin-scale and demonstrate how they vary with watershed properties, 2) emphasize applications of hydrologic concepts rather than computer programming, 3) elucidate the underlying physical processes that can often be obscured with a complicated "off-the-shelf" watershed model in an introductory hydrology course, and 4) reduce the learning curve associated with analyzing meaningful real-world problems. The open-access MOD-WET and e-textbook have already been successfully incorporated within our undergraduate curriculum.

Peer review of RELAP5/MOD3 documentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Craddick, W.G.

1993-12-31

A peer review was performed on a portion of the documentation of the RELAP5/MOD3 computer code. The review was performed in two phases. The first phase was a review of Volume 3, Developmental Assessment problems, and Volume 4, Models and Correlations. The reviewers for this phase were Dr. Peter Griffith, Dr. Yassin Hassan, Dr. Gerald S. Lellouche, Dr. Marino di Marzo and Mr. Mark Wendel. The reviewers recommended a number of improvements, including using a frozen version of the code for assessment guided by a validation plan, better justification for flow regime maps and extension of models beyond their datamore » base. The second phase was a review of Volume 6, Quality Assurance of Numerical Techniques in RELAP5/MOD3. The reviewers for the second phase were Mr. Mark Wendel and Dr. Paul T. Williams. Recommendations included correction of numerous grammatical and typographical errors and better justification for the use of Lax`s Equivalence Theorem.« less

A New Network Modeling Tool for the Ground-based Nuclear Explosion Monitoring Community

NASA Astrophysics Data System (ADS)

Merchant, B. J.; Chael, E. P.; Young, C. J.

2013-12-01

Network simulations have long been used to assess the performance of monitoring networks to detect events for such purposes as planning station deployments and network resilience to outages. The standard tool has been the SAIC-developed NetSim package. With correct parameters, NetSim can produce useful simulations; however, the package has several shortcomings: an older language (FORTRAN), an emphasis on seismic monitoring with limited support for other technologies, limited documentation, and a limited parameter set. Thus, we are developing NetMOD (Network Monitoring for Optimal Detection), a Java-based tool designed to assess the performance of ground-based networks. NetMOD's advantages include: coded in a modern language that is multi-platform, utilizes modern computing performance (e.g. multi-core processors), incorporates monitoring technologies other than seismic, and includes a well-validated default parameter set for the IMS stations. NetMOD is designed to be extendable through a plugin infrastructure, so new phenomenological models can be added. Development of the Seismic Detection Plugin is being pursued first. Seismic location and infrasound and hydroacoustic detection plugins will follow. By making NetMOD an open-release package, it can hopefully provide a common tool that the monitoring community can use to produce assessments of monitoring networks and to verify assessments made by others.

Flux-driven turbulence GDB simulations of the IWL Alcator C-Mod L-mode edge compared with experiment

NASA Astrophysics Data System (ADS)

Francisquez, Manaure; Zhu, Ben; Rogers, Barrett

2017-10-01

Prior to predicting confinement regime transitions in tokamaks one may need an accurate description of L-mode profiles and turbulence properties. These features determine the heat-flux width upon which wall integrity depends, a topic of major interest for research aid to ITER. To this end our work uses the GDB model to simulate the Alcator C-Mod edge and contributes support for its use in studying critical edge phenomena in current and future tokamaks. We carried out 3D electromagnetic flux-driven two-fluid turbulence simulations of inner wall limited (IWL) C-Mod shots spanning closed and open flux surfaces. These simulations are compared with gas puff imaging (GPI) and mirror Langmuir probe (MLP) data, examining global features and statistical properties of turbulent dynamics. GDB reproduces important qualitative aspects of the C-Mod edge regarding global density and temperature profiles, within reasonable margins, and though the turbulence statistics of the simulated turbulence follow similar quantitative trends questions remain about the code's difficulty in exactly predicting quantities like the autocorrelation time A proposed breakpoint in the near SOL pressure and the posited separation between drift and ballooning dynamics it represents are examined This work was supported by DOE-SC-0010508. This research used resources of the National Energy Research Scientific Computing Center (NERSC).

Feedback system for divertor impurity seeding based on real-time measurements of surface heat flux in the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Brunner, D.; Burke, W.; Kuang, A. Q.; LaBombard, B.; Lipschultz, B.; Wolfe, S.

2016-02-01

Mitigation of the intense heat flux to the divertor is one of the outstanding problems in fusion energy. One technique that has shown promise is impurity seeding, i.e., the injection of low-Z gaseous impurities (typically N2 or Ne) to radiate and dissipate the power before it arrives to the divertor target plate. To this end, the Alcator C-Mod team has created a first-of-its-kind feedback system to control the injection of seed gas based on real-time surface heat flux measurements. Surface thermocouples provide real-time measurements of the surface temperature response to the plasma heat flux. The surface temperature measurements are inputted into an analog computer that "solves" the 1-D heat transport equation to deliver accurate, real-time signals of the surface heat flux. The surface heat flux signals are sent to the C-Mod digital plasma control system, which uses a proportional-integral-derivative (PID) algorithm to control the duty cycle demand to a pulse width modulated piezo valve, which in turn controls the injection of gas into the private flux region of the C-Mod divertor. This paper presents the design and implementation of this new feedback system as well as initial results using it to control divertor heat flux.

Feedback system for divertor impurity seeding based on real-time measurements of surface heat flux in the Alcator C-Mod tokamak.

PubMed

Brunner, D; Burke, W; Kuang, A Q; LaBombard, B; Lipschultz, B; Wolfe, S

2016-02-01

Mitigation of the intense heat flux to the divertor is one of the outstanding problems in fusion energy. One technique that has shown promise is impurity seeding, i.e., the injection of low-Z gaseous impurities (typically N2 or Ne) to radiate and dissipate the power before it arrives to the divertor target plate. To this end, the Alcator C-Mod team has created a first-of-its-kind feedback system to control the injection of seed gas based on real-time surface heat flux measurements. Surface thermocouples provide real-time measurements of the surface temperature response to the plasma heat flux. The surface temperature measurements are inputted into an analog computer that "solves" the 1-D heat transport equation to deliver accurate, real-time signals of the surface heat flux. The surface heat flux signals are sent to the C-Mod digital plasma control system, which uses a proportional-integral-derivative (PID) algorithm to control the duty cycle demand to a pulse width modulated piezo valve, which in turn controls the injection of gas into the private flux region of the C-Mod divertor. This paper presents the design and implementation of this new feedback system as well as initial results using it to control divertor heat flux.

Extension of the lod score: the mod score.

PubMed

Clerget-Darpoux, F

2001-01-01

In 1955 Morton proposed the lod score method both for testing linkage between loci and for estimating the recombination fraction between them. If a disease is controlled by a gene at one of these loci, the lod score computation requires the prior specification of an underlying model that assigns the probabilities of genotypes from the observed phenotypes. To address the case of linkage studies for diseases with unknown mode of inheritance, we suggested (Clerget-Darpoux et al., 1986) extending the lod score function to a so-called mod score function. In this function, the variables are both the recombination fraction and the disease model parameters. Maximizing the mod score function over all these parameters amounts to maximizing the probability of marker data conditional on the disease status. Under the absence of linkage, the mod score conforms to a chi-square distribution, with extra degrees of freedom in comparison to the lod score function (MacLean et al., 1993). The mod score is asymptotically maximum for the true disease model (Clerget-Darpoux and Bonaïti-Pellié, 1992; Hodge and Elston, 1994). Consequently, the power to detect linkage through mod score will be highest when the space of models where the maximization is performed includes the true model. On the other hand, one must avoid overparametrization of the model space. For example, when the approach is applied to affected sibpairs, only two constrained disease model parameters should be used (Knapp et al., 1994) for the mod score maximization. It is also important to emphasize the existence of a strong correlation between the disease gene location and the disease model. Consequently, there is poor resolution of the location of the susceptibility locus when the disease model at this locus is unknown. Of course, this is true regardless of the statistics used. The mod score may also be applied in a candidate gene strategy to model the potential effect of this gene in the disease. Since, however, it ignores the information provided both by disease segregation and by linkage disequilibrium between the marker alleles and the functional disease alleles, its power of discrimination between genetic models is weak. The MASC method (Clerget-Darpoux et al., 1988) has been designed to address more efficiently the objectives of a candidate gene approach.

A biphasic epigenetic switch controls immunoevasion, virulence and niche adaptation in non-typeable Haemophilus influenzae.

PubMed

Atack, John M; Srikhanta, Yogitha N; Fox, Kate L; Jurcisek, Joseph A; Brockman, Kenneth L; Clark, Tyson A; Boitano, Matthew; Power, Peter M; Jen, Freda E-C; McEwan, Alastair G; Grimmond, Sean M; Smith, Arnold L; Barenkamp, Stephen J; Korlach, Jonas; Bakaletz, Lauren O; Jennings, Michael P

2015-07-28

Non-typeable Haemophilus influenzae contains an N(6)-adenine DNA-methyltransferase (ModA) that is subject to phase-variable expression (random ON/OFF switching). Five modA alleles, modA2, modA4, modA5, modA9 and modA10, account for over two-thirds of clinical otitis media isolates surveyed. Here, we use single molecule, real-time (SMRT) methylome analysis to identify the DNA-recognition motifs for all five of these modA alleles. Phase variation of these alleles regulates multiple proteins including vaccine candidates, and key virulence phenotypes such as antibiotic resistance (modA2, modA5, modA10), biofilm formation (modA2) and immunoevasion (modA4). Analyses of a modA2 strain in the chinchilla model of otitis media show a clear selection for ON switching of modA2 in the middle ear. Our results indicate that a biphasic epigenetic switch can control bacterial virulence, immunoevasion and niche adaptation in an animal model system.

Evidence for Chaotic Edge Turbulence in the Alcator C-Mod Tokamak

NASA Astrophysics Data System (ADS)

Zhu, Ziyan; White, Anne; Carter, Troy; Terry, Jim; Baek, Seung Gyou

2016-10-01

Turbulence greatly reduces the confinement time of magnetic-confined plasmas; understanding the nature of this turbulence and the associated transport is therefore of great importance. This research seeks to establish whether turbulent fluctuations in Alcator C-Mod are chaotic or stochastic. This has an important impact on transport caused by turbulence in C-Mod: stochastic fluctuations sample all of phase space and can lead to diffusive transport, whereas chaotic fluctuations live in a restricted phase space (e.g. on attractors) and a diffusive description may not be valid. By analyzing the time series from an O-Mode reflectometer, turbulent edge density fluctuations in Ohmic plasmas and L-mode plasmas in the Alcator C-Mod tokamak are shown to be chaotic. Supporting evidence for chaos in the edge region includes: the observation of an exponential power spectra (which is associated with Lorentzian-shaped pulses in the time series) and the location of the signal in the Complexity-Entropy plane (C-H plane) and its corresponding Brandt-Pompe (BP) probability distribution. These analysis techniques will be briefly introduced along with a discussion of the analysis results. Different diagnostic techniques, such as Gas Puff Imaging (GPI), could be used to confirm the results. Work supported by the U.S. Department of Energy Office of Science under Agreement DE-FC02-99ER54512 and DE-FC02-07ER54918:011.

Educational Outreach at the M.I.T. Plasma Fusion Center

NASA Astrophysics Data System (ADS)

Censabella, V.

1996-11-01

Educational outreach at the MIT Plasma Fusion Center consists of volunteers working together to increase the public's knowledge of fusion and plasma-related experiments. Seeking to generate excitement about science, engineering and mathematics, the PFC holds a number of outreach activities throughout the year, such as Middle and High School Outreach Days. Outreach also includes the Mr. Magnet Program, which uses an interactive strategy to engage elementary school children. Included in this year's presentation will be a new and improved C-MOD Jr, a confinement video game which helps students to discover how computers manipulate magnetic pulses to keep a plasma confined for as long as possible. Also on display will be an educational toy created by the Cambridge Physics Outlet, a PFC spin-off company. The PFC maintains a Home Page on the World Wide Web, which can be reached at http://cmod2.pfc.mit.edu/.

Mod Genius

ERIC Educational Resources Information Center

Grayson, Jennifer

2010-01-01

This article discusses how Watkinson School head John Bracker was able to accomplish the school's plan of having a new science building that would meet all of their needs: innovative building that offers a range of eco-friendly features, an inspiring learning environment, and even better, the right price. Bracker contemplates on a structure that…

Logistics Implications of Maneuver Warfare. Volume 3. Soviet Offensive Concepts and Capabilities

DTIC Science & Technology

1988-10-01

science, in contrast to military doctrine, is under the jurisdiction of the Ministry of Defense (MoD). Unlike military doctrine, military science is open...of State, and published under auspices of the U.S. Air Force. 5lbid. 6 Sovetskaia Voennaia Entsiklopediia, Vol. 6 (Moscow: Voenizdat, 1978). The Soviet...be nuclear, global, nor unlimited.11 Under that notion, while World War III would probably escalate to nuclear war, it would start with a long

Break modeling for RELAP5 analyses of ISP-27 Bethsy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petelin, S.; Gortnar, O.; Mavko, B.

This paper presents pre- and posttest analyses of International Standard Problem (ISP) 27 on the Bethsy facility and separate RELAP5 break model tests considering the measured boundary condition at break inlet. This contribution also demonstrates modifications which have assured the significant improvement of model response in posttest simulations. Calculations were performed using the RELAP5/MOD2/36.05 and RELAP5/MOD3.5M5 codes on the MicroVAX, SUN, and CONVEX computers. Bethsy is an integral test facility that simulates a typical 900-MW (electric) Framatome pressurized water reactor. The ISP-27 scenario involves a 2-in. cold-leg break without HPSI and with delayed operator procedures for secondary system depressurization.

ERDC MSRC (Major Shared Resource Center) Resource. High Performance Computing for the Warfighter. Fall 2008

DTIC Science & Technology

2008-01-01

32 “Solving the Hard Problems” at UGC 2008 in Seattle By Rose J. Dykes, ERDC MSRC...two fields to remain competitive in the global market . The ERDC MSRC attempts to take every available opportunity to encourage students to enter these...Attendees of the 18th annual DoD High Performance Computing Mod ern- ization Pr ogram (HPCMP) Users Gr oup Confer ence ( UGC

High-Fidelity Simulations of Electromagnetic Propagation and RF Communication Systems

DTIC Science & Technology

2017-05-01

addition to high -fidelity RF propagation modeling, lower-fidelity mod- els, which are less computationally burdensome, are available via a C++ API...expensive to perform, requiring roughly one hour of computer time with 36 available cores and ray tracing per- formed by a single high -end GPU...ER D C TR -1 7- 2 Military Engineering Applied Research High -Fidelity Simulations of Electromagnetic Propagation and RF Communication

Prediction and realization of ITER-like pedestal pressure in the high- B tokamak Alcator C-Mod

NASA Astrophysics Data System (ADS)

Hughes, Jerry

2017-10-01

Fusion power in a burning plasma will scale as the square of the plasma pressure, which is increased in a straightforward way by increasing magnetic field: Pfus p2 B4 . Experiments on Alcator C-Mod, a compact high- B tokamak, have tested predictive capability for pedestal pressure, at toroidal field BT up to 8T , and poloidal field BP up to 1T . These reactor-like fields enable C-Mod to approach an ITER predicted value of 90kPa . This is expected if, as in the EPED model, the pedestal is constrained by onset of kinetic ballooning modes (KBMs) and peeling-ballooning modes (PMB), yielding a pressure pedestal approximately as pped BT ×BP . One successful path to high confinement on C-Mod is the high-density (ne > 3 ×1020m-3) approach, pursued using enhanced D-alpha (EDAs) H-mode. In EDA H-mode, transport regulates both the pedestal profiles and the core impurity content, holding the pedestal stationary, at just below the PBM stability boundary. We have extended this stationary ELM-suppressed regime to the highest magnetic fields achievable on C-Mod, and used it to approach the maximum pedestal predicted by EPED at high density: pped 60kPa . Another approach to high pressure utilizes a pedestal limited by PBMs at low collisionality, where pressure increases with density and EPED predicts access to a higher ``Super H'' solution for pped. Experiments at reduced density (ne < 2 ×1020m-3) and strong plasma shaping (δ > 0.5) accessed these regimes on C-Mod, producing pedestals with world record pped 80kPa , at Tped 2keV . In both the high and low density approaches, the impact of the pedestal on core performance is substantial. Our exploration of high pedestal regimes yielded a volume-averaged pressure 〈 p 〉 > 2atm , a world record value for a magnetic fusion device. The results hold promise for the projection of pedestal pressure and overall performance of high field burning plasma devices. Supported by U.S. Department of Energy awards DE-FC02-99ER54512, DE-FG02-95ER54309, DE-FC02-06ER54873, DE-AC02-09CH11466, DE-SC0007880 using Alcator C-Mod, a DOE Office of Science User Facility.

Digital Plasma Control System for Alcator C-Mod

NASA Astrophysics Data System (ADS)

Ferrara, M.; Wolfe, S.; Stillerman, J.; Fredian, T.; Hutchinson, I.

2004-11-01

A digital plasma control system (DPCS) has been designed to replace the present C-Mod system, which is based on hybrid analog-digital computer. The initial implementation of DPCS comprises two 64 channel, 16 bit, low-latency cPCI digitizers, each with 16 analog outputs, controlled by a rack-mounted single-processor Linux server, which also serves as the compute engine. A prototype system employing three older 32 channel digitizers was tested during the 2003-04 campaign. The hybrid's linear PID feedback system was emulated by IDL code executing a synchronous loop, using the same target waveforms and control parameters. Reliable real-time operation was accomplished under a standard Linux OS (RH9) by locking memory and disabling interrupts during the plasma pulse. The DPCS-computed outputs agreed to within a few percent with those produced by the hybrid system, except for discrepancies due to offsets and non-ideal behavior of the hybrid circuitry. The system operated reliably, with no sample loss, at more than twice the 10kHz design specification, providing extra time for implementing more advanced control algorithms. The code is fault-tolerant and produces consistent output waveforms even with 10% sample loss.

Pediatric Multiple Organ Dysfunction Syndrome: Promising Therapies

PubMed Central

Doctor, Allan; Zimmerman, Jerry; Agus, Michael; Rajasekaran, Surender; Wardenburg, Juliane Bubeck; Fortenberry, James; Zajicek, Anne; Typpo, Katri

2016-01-01

Objective To describe the state of the science, identify knowledge gaps, and offer potential future research questions regarding promising therapies for children with multiple organ dysfunction syndrome (MODS) presented during the Eunice Kennedy Shriver National Institute of Child Health and Human Development Workshop on Pediatric Multiple Organ Dysfunction Syndrome (March 26-27, 2015). Data Sources Literature review, research data, and expert opinion. Study Selection Not applicable. Data Extraction Moderated by an expert from the field, issues relevant to the association of MODS with a variety of conditions were presented, discussed and debated with a focus on identifying knowledge gaps and research priorities. Data Synthesis Summary of presentations and discussion supported and supplemented by relevant literature. Conclusions Among critically ill children, MODS is relatively common and associated with significant morbidity and mortality. For outcomes to improve, effective therapies aimed at preventing and treating this condition must be discovered and rigorously evaluated. In this manuscript, a number of potential opportunities to enhance current care are highlighted including the need for a better understanding of the pharmacokinetics and pharmacodynamics of medications, the effect of early and optimized nutrition, and the impact of effective glucose control in the setting of MODS. Additionally, a handful of the promising therapies either currently being implemented or developed are described. These include extracorporeal therapies, anti-cytokine therapies, anti-toxin treatments, anti-oxidant approaches and multiple forms of exogenous steroids. For the field to advance, these and other therapies must be assessed in rigorous manner and implemented accordingly. PMID:28248836

Modélisation par éléments finis 3D du champ magnétostatique dans les enroulements des réactances cuirassées de grande puissance. Comparaison avec le calcul en 2D

NASA Astrophysics Data System (ADS)

Ngnegueu, Triomphant; Terme, Claude; Mailhot, Michel

1993-03-01

In this paper, the finite element method is applied for the computation of the magnetostatic field in the windings of a shell-form reactor. The modeling is carried out in 3D, using FLUX3D, a software developed at the Laboratoire d'Electrotechnique de Grenoble. The results are compared to those obtained in 2D. These calculation results are also compared to some test results. Dans cet article, nous décrivons une application de la méthode des éléments finis pour la modélisation du champ magnétostatique dans les enroulements d'une réactance cuirassée de grande puissance. La modélisation est conduite en 3D, en utilisant le logiciel FLUX3D. Les résultats du calcul sont comparés avec ceux obtenus en 2D. Quelques comparaisons sont aussi effectuées avec des résultats de mesure.

C-Mod MHD stability analysis with LHCD

NASA Astrophysics Data System (ADS)

Ebrahimi, Fatima; Bhattacharjee, A.; Delgado, L.; Scott, S.; Wilson, J. R.; Wallace, G. M.; Shiraiwa, S.; Mumgaard, R. T.

2016-10-01

In lower hybrid current drive (LHCD) experiments on the Alcator C-Mod, sawtooth activity could be suppressed as the safety factor q on axis is raised above unity. However, in some of these experiments, after applying LHCD, the onset of MHD mode activity caused the current drive efficiency to significantly drop. Here, we study the stability of these experiments by performing MHD simulations using the NIMROD code starting with experimental EFIT equilibria. First, consistent with the LHCD experiment with no signature of MHD activity, MHD mode activity was also absent in the simulations. Second, for experiments with MHD mode activity, we find that a core n=1 reconnecting mode with dominate poloidal modes of m=2,3 is unstable. This mode is a resistive current-driven mode as its growth rate scales with a negative power of the Lundquist number in the simulations. In addition, with further enhanced reversed-shear q profile in the simulations, a core double tearing mode is found to be unstable. This work is supported by U.S. DOE cooperative agreement DE-FC02-99ER54512 using the Alcator C-Mod tokamak, a DOE Office of Science user facility.

ENVIRONMENTAL RESEARCH BRIEF : ANALYTIC ELEMENT MODELING OF GROUND-WATER FLOW AND HIGH PERFORMANCE COMPUTING

EPA Science Inventory

Several advances in the analytic element method have been made to enhance its performance and facilitate three-dimensional ground-water flow modeling in a regional aquifer setting. First, a new public domain modular code (ModAEM) has been developed for modeling ground-water flow ...

Potential of VIIRS Data for Regional Monitoring of Gypsy Moth Defoliation: Implications for Forest Threat Early Warning System

NASA Technical Reports Server (NTRS)

Spruce, Joseph P.; Ryan, Robert E.; Smoot, James C.; Prados, Donald; McKellip, Rodney; Sader. Steven A.; Gasser, Jerry; May, George; Hargrove, William

2007-01-01

A NASA RPC (Rapid Prototyping Capability) experiment was conducted to assess the potential of VIIRS (Visible/Infrared Imager/Radiometer Suite) data for monitoring non-native gypsy moth (Lymantria dispar) defoliation of forests. This experiment compares defoliation detection products computed from simulated VIIRS and from MODIS (Moderate Resolution Imaging Spectroradiometer) time series products as potential inputs to a forest threat EWS (Early Warning System) being developed for the USFS (USDA Forest Service). Gypsy moth causes extensive defoliation of broadleaved forests in the United States and is specifically identified in the Healthy Forest Restoration Act (HFRA) of 2003. The HFRA mandates development of a national forest threat EWS. This system is being built by the USFS and NASA is aiding integration of needed satellite data products into this system, including MODIS products. This RPC experiment enabled the MODIS follow-on, VIIRS, to be evaluated as a data source for EWS forest monitoring products. The experiment included 1) assessment of MODIS-simulated VIIRS NDVI products, and 2) evaluation of gypsy moth defoliation mapping products from MODIS-simulated VIIRS and from MODIS NDVI time series data. This experiment employed MODIS data collected over the approximately 15 million acre mid-Appalachian Highlands during the annual peak defoliation time frame (approximately June 10 through July 27) during 2000-2006. NASA Stennis Application Research Toolbox software was used to produce MODIS-simulated VIIRS data and NASA Stennis Time Series Product Tool software was employed to process MODIS and MODIS-simulated VIIRS time series data scaled to planetary reflectance. MODIS-simulated VIIRS data was assessed through comparison to Hyperion-simulated VIIRS data using data collected during gypsy moth defoliation. Hyperion-simulated MODIS data showed a high correlation with actual MODIS data (NDVI R2 of 0.877 and RMSE of 0.023). MODIS-simulated VIIRS data for the same date showed moderately high correlation with Hyperion-simulated VIIRS data (NDVI R2 of 0.62 and RMSE of 0.035), even though the datasets were collected about a half an hour apart during changing weather conditions. MODIS products (MOD02, MOD09, and MOD13) and MOD02-simulated VIIRS time series data were used to generate defoliation mapping products based on image classification and image differencing change detection techniques. Accuracy of final defoliation mapping products was assessed by image interpreting over 170 randomly sampled locations found on Landsat and ASTER data in conjunction with defoliation map data from the USFS. The MOD02-simulated VIIRS 400-meter NDVI classification produced a similar overall accuracy (87.28 percent with 0.72 Kappa) to the MOD02 250-meter NDVI classification (86.71 percent with 0.71 Kappa). In addition, the VIIRS 400-meter NDVI, MOD02 250-meter NDVI, and MOD02 500-meter NDVI showed good user and producer accuracies for the defoliated forest class (70 percent) and acceptable Kappa values (0.66). MOD02 and MOD02-simulated VIIRS data both showed promise as data sources for regional monitoring of forest disturbance due to insect defoliation.

Algorithmic Complexity. Volume II.

DTIC Science & Technology

1982-06-01

digital computers, this improvement will go unnoticed if only a few complex products are to be taken, however it can become increasingly important as...computed in the reverse order. If the products are formed moving from the top of the tree downward, and then the divisions are performed going from the...the reverse order, going up the tree. (r- a mod m means that r is the remainder when a is divided by M.) The overall running time of the algorithm is

B61 Mod 12 Life Extension Program Tailkit Assembly (B61 Mod 12 LEP TKA)

DTIC Science & Technology

2013-12-01

Selected Acquisition Report (SAR) RCS: DD-A&T(Q&A)823-468 B61 Mod 12 Life Extension Program Tailkit Assembly ( B61 Mod 12 LEP TKA...REPORT TYPE 3. DATES COVERED 00-00-2013 to 00-00-2013 4. TITLE AND SUBTITLE B61 Mod 12 Life Extension Program Tailkit Assembly ( B61 Mod 12 LEP...REPORT unclassified b. ABSTRACT unclassified c. THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 B61 Mod 12

Prediction of global and local model quality in CASP8 using the ModFOLD server.

PubMed

McGuffin, Liam J

2009-01-01

The development of effective methods for predicting the quality of three-dimensional (3D) models is fundamentally important for the success of tertiary structure (TS) prediction strategies. Since CASP7, the Quality Assessment (QA) category has existed to gauge the ability of various model quality assessment programs (MQAPs) at predicting the relative quality of individual 3D models. For the CASP8 experiment, automated predictions were submitted in the QA category using two methods from the ModFOLD server-ModFOLD version 1.1 and ModFOLDclust. ModFOLD version 1.1 is a single-model machine learning based method, which was used for automated predictions of global model quality (QMODE1). ModFOLDclust is a simple clustering based method, which was used for automated predictions of both global and local quality (QMODE2). In addition, manual predictions of model quality were made using ModFOLD version 2.0--an experimental method that combines the scores from ModFOLDclust and ModFOLD v1.1. Predictions from the ModFOLDclust method were the most successful of the three in terms of the global model quality, whilst the ModFOLD v1.1 method was comparable in performance to other single-model based methods. In addition, the ModFOLDclust method performed well at predicting the per-residue, or local, model quality scores. Predictions of the per-residue errors in our own 3D models, selected using the ModFOLD v2.0 method, were also the most accurate compared with those from other methods. All of the MQAPs described are publicly accessible via the ModFOLD server at: http://www.reading.ac.uk/bioinf/ModFOLD/. The methods are also freely available to download from: http://www.reading.ac.uk/bioinf/downloads/. Copyright 2009 Wiley-Liss, Inc.

Effect of milk replacer feeding rate, age at weaning, and method of reducing milk replacer to weaning on digestion, performance, rumination, and activity in dairy calves to 4 months of age.

PubMed

Dennis, T S; Suarez-Mena, F X; Hill, T M; Quigley, J D; Schlotterbeck, R L; Hulbert, L

2018-01-01

The objectives of this study were to evaluate calf performance, diet digestibility, and rumination activity when feeding 4 milk replacer (MR) feeding programs. Male Holstein calves (n = 96; 43 ± 1.2 kg of body weight; 1 to 2 d of age) were housed in individual pens for 56 d. Calves were fed a common MR [25% crude protein (CP), 17% fat, dry matter (DM) basis]. Feeding programs were (1) 0.66 kg of DM/d of MR and weaning at 42 d (MOD6); (2) up to 1.09 kg of DM/d of MR weaned at 42 d (HIGH6); (3) up to 1.09 kg of DM/d of MR weaned at 53 d (HIGH8); and (4) up to 1.09 kg of DM/d of MR and gradually weaned from d 35 to 53 (GRAD8). Calves were fed a textured starter containing whole grains with 20% CP and 37% starch (DM basis). From 38 to 56 d of age, 4 calves/treatment had ear tag accelerometers fitted to provide measurements for eating, rumination, and activity. Calves were moved into groups by treatment (4 calves/pen) at 56 d and fed the same starter blended with 5% hay. Fecal samples were collected for individual calves between d 31 to 35, 45 to49 (MOD6 and HIGH6 only), and 56 to 60 from 5 calves/treatment. Fecal samples were collected by pen from d 80 to 84 and 108 to 112. Data were analyzed as a randomized complete block design with repeated measures when appropriate. Preplanned contrasts of MOD6 versus others, HIGH6 versus HIGH8, and HIGH8 versus GRAD8 were used to separate the means. Calves fed MOD6 were 3.4 kg lighter at 56 d than calves fed other treatments. Starter intake was greatest for MOD6 compared with other treatments (0.78 vs. 0.43 kg/d) from 0 to 56 d. Hip width and body condition score change from 0 to 56 d were similar among treatments. Average time ruminating, eating, and activity did not differ among treatments. Total-tract digestibility of DM, OM, CP, and fat were least for calves fed MOD6 versus other treatments on d 35, whereas NDF and starch digestibility were greatest for MOD6 at d 35. Digestibility of ADF and NDF were also greatest for MOD6 at d 49 (compared with HIGH6 only) and 60. From d 56 to 112, calves previously fed MOD6 had greater ADG versus other treatments. At 84 d, DM, OM, CP, NDF, ADF, and fat digestibility were greatest for calves fed MOD6 versus others. Calves fed HIGH6 and GRAD8 had greater digestibility of NDF and ADF compared with HIGH8 at 84 d. At 112 d, digestibility was similar among treatments. Calves were not different in BW and hip width at 112 d, with growth driven by less digestion of DM and fiber around and after weaning for calves fed >0.66 kg of MR. Gradual weaning did improve postweaning digestion. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Kinetic studies of divertor heat fluxes in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Pankin, A. Y.; Bateman, G.; Kritz, A. H.; Rafiq, T.; Park, G. Y.; Chang, C. S.; Brunner, D.; Hughes, J. W.; Labombard, B.; Terry, J.

2010-11-01

The kinetic XGC0 code [C.S. Chang et al, Phys. Plasmas 11 (2004) 2649] is used to model the H- mode pedestal and SOL regions in Alcator C-Mod discharges. The self-consistent simulations in this study include kinetic neoclassical physics and anomalous transport models along with the ExB flow shear effects. The heat fluxes on the divertor plates are computed and the fluxes to the outer plate are compared with experimental observations. The dynamics of the radial electric field near the separatrix and in the SOL region are computed with the XGC0 code, and the effect of the anomalous transport on the heat fluxes in the SOL region is investigated. In particular, the particle and thermal diffusivities obtained in the analysis mode are compared with predictions from the theory-based anomalous transport models such as MMM95 [G. Bateman et al, Phys. Plasmas 5 (1998) 1793] and DRIBM [T. Rafiq et al, to appear in Phys. Plasmas (2010)]. It is found that there is a notable pinch effect in the inner separatrix region. Possible physical mechanisms for the particle and thermal pinches are discussed.

The RANDOM computer program: A linear congruential random number generator

NASA Technical Reports Server (NTRS)

Miles, R. F., Jr.

1986-01-01

The RANDOM Computer Program is a FORTRAN program for generating random number sequences and testing linear congruential random number generators (LCGs). The linear congruential form of random number generator is discussed, and the selection of parameters of an LCG for a microcomputer described. This document describes the following: (1) The RANDOM Computer Program; (2) RANDOM.MOD, the computer code needed to implement an LCG in a FORTRAN program; and (3) The RANCYCLE and the ARITH Computer Programs that provide computational assistance in the selection of parameters for an LCG. The RANDOM, RANCYCLE, and ARITH Computer Programs are written in Microsoft FORTRAN for the IBM PC microcomputer and its compatibles. With only minor modifications, the RANDOM Computer Program and its LCG can be run on most micromputers or mainframe computers.

New MHD feedback control schemes using the MARTe framework in RFX-mod

NASA Astrophysics Data System (ADS)

Piron, Chiara; Manduchi, Gabriele; Marrelli, Lionello; Piovesan, Paolo; Zanca, Paolo

2013-10-01

Real-time feedback control of MHD instabilities is a topic of major interest in magnetic thermonuclear fusion, since it allows to optimize a device performance even beyond its stability bounds. The stability properties of different magnetic configurations are important test benches for real-time control systems. RFX-mod, a Reversed Field Pinch experiment that can also operate as a tokamak, is a well suited device to investigate this topic. It is equipped with a sophisticated magnetic feedback system that controls MHD instabilities and error fields by means of 192 active coils and a corresponding grid of sensors. In addition, the RFX-mod control system has recently gained new potentialities thanks to the introduction of the MARTe framework and of a new CPU architecture. These capabilities allow to study new feedback algorithms relevant to both RFP and tokamak operation and to contribute to the debate on the optimal feedback strategy. This work focuses on the design of new feedback schemes. For this purpose new magnetic sensors have been explored, together with new algorithms that refine the de-aliasing computation of the radial sideband harmonics. The comparison of different sensor and feedback strategy performance is described in both RFP and tokamak experiments.

Méthodes de type éléments finis pour le calcul des champs électriques et magnétiques en électroencéphalographie et magnétoencéphalographie

NASA Astrophysics Data System (ADS)

Guérin, Christophe; Marin, Gildas; Garnero, Line; Meunier, Gérard

1997-12-01

So as to compute the electric potential and the flux density generated by the electrical activity of the brain, numerical methods based on the Finite Element Method have been developed. These methods, which can treat realistic head models and can take into account anisotropy of conductivity, for instance in the skull, are presented. Then two numerical examples are described: a spherical model and a realistic head model. Afin de calculer le potentiel électrique et l'induction créés par l'activité électrique du cerveau, nous avons développé des méthodes utilisant la Méthode des Éléments Finis. Ces méthodes, qui peuvent s'appliquer à des modèles réalistes de tête et qui permettent de tenir compte de la conductivité anisotrope de certains tissus comme l'os, sont présentées. Puis deux exemples numériques sont décrits : un modèle de sphères concentriques et un modèle réaliste de tête.

Effects of milk replacer program fed 2 or 4 times daily on nutrient intake and calf growth.

PubMed

Kmicikewycz, A D; da Silva, D N L; Linn, J G; Litherland, N B

2013-02-01

The aims of this study were to determine if feeding frequency (FF) of milk replacer (MR; meals/d) alters starter intake, growth, and efficiency of growth in nursery calves fed a conventional or accelerated MR. We hypothesized that smaller and more frequent MR meals would increase starter intake and growth when greater amounts of MR nutrients are fed to nursery calves. Forty-eight Holstein and Holstein-cross heifer and bull calves were assigned to treatments in a 2 × 2 factorial arrangement of MR and FF. Treatments included (1) standard 20% CP and 20% fat MR fed at 1.5% of body weight (BW; 2 meals/d; STD2), (2) standard 20% CP and 20% fat MR fed at 1.5% of BW (4 meals/d; STD4), (3) modified 26% CP and 18% fat MR fed at 2.0% of BW (2 meals/d; MOD2), and (4) modified 26% CP and 18% fat MR fed at 2.0% of BW (4 meals/d; MOD4; n=12). All calves were fed at 0600 and 1700 h and STD4 and MOD4 calves were fed 2 additional meals at 1100 and 1400 h, resulting in the same amount of MR offered for the 2 × and 4 × treatments. Treatments were fed from d 2 to 42 of age and all MR feeding rates were adjusted weekly to maintain MR solids intakes at 1.5 or 2.0% of BW for STD and MOD diets, respectively, and were reconstituted to 15% total solids. Milk replacer FF was reduced by 50% on d 36 and calves were weaned on d 42. Calves were housed in hutches bedded with straw and offered water and a texturized 18% CP starter ad libitum. Calf body weight and body structure were measured weekly and starter intake and fecal scores were measured daily. Through both 42 and 56 d, calves fed MOD had greater CP and fat intake, resulting in increased average daily gain, heart girth, circulating nonesterified fatty acids (NEFA), and muscle total lipid compared with calves fed STD diets. Calves fed MOD diets consumed less starter grain than STD calves but total dry matter intake was similar among treatments. Increased FF for STD calves resulted in greater starter intake at weaning but increasing FF of MOD calves did not have this effect. Due to differences in starter intake, total dry matter by calves through d 56 was similar across treatments. Additionally, increased FF tended to increase serum NEFA concentrations. Serum NEFA concentration was negatively correlated with starter intake. The BW of calves fed STD2 and STD4 treatments almost doubled and the BW of calves on the MOD2 and MOD4 treatments doubled by d 56. Increased FF of the conventional MR program but not accelerated MR program increased starter intake. Increased FF did not affect growth, starter intake, or gain:feed ratio. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Comparison of computer codes for calculating dynamic loads in wind turbines

NASA Technical Reports Server (NTRS)

Spera, D. A.

1977-01-01

Seven computer codes for analyzing performance and loads in large, horizontal axis wind turbines were used to calculate blade bending moment loads for two operational conditions of the 100 kW Mod-0 wind turbine. Results were compared with test data on the basis of cyclic loads, peak loads, and harmonic contents. Four of the seven codes include rotor-tower interaction and three were limited to rotor analysis. With a few exceptions, all calculated loads were within 25 percent of nominal test data.

A Field Evaluation of the Hardy TB MODS Kit™ for the Rapid Phenotypic Diagnosis of Tuberculosis and Multi-Drug Resistant Tuberculosis

PubMed Central

Martin, Laura; Coronel, Jorge; Faulx, Dunia; Valdez, Melissa; Metzler, Mutsumi; Crudder, Chris; Castillo, Edith; Caviedes, Luz; Grandjean, Louis; Rodriguez, Mitzi; Friedland, Jon S.; Gilman, Robert H.; Moore, David A. J.

2014-01-01

Background Even though the WHO-endorsed, non-commercial MODS assay offers rapid, reliable TB liquid culture and phenotypic drug susceptibility testing (DST) at lower cost than any other diagnostic, uptake has been patchy. In part this reflects misperceptions about in-house assay quality assurance, but user convenience of one-stop procurement is also important. A commercial MODS kit was developed by Hardy Diagnostics (Santa Maria, CA, USA) with PATH (Seattle, WA, USA) to facilitate procurement, simplify procedures through readymade media, and enhance safety with a sealing silicone plate lid. Here we report the results from a large-scale field evaluation of the MODS kit in a government service laboratory. Methods & Findings 2446 sputum samples were cultured in parallel in Lowenstein-Jensen (LJ), conventional MODS and in the MODS kit. MODS kit DST was compared with conventional MODS (direct) DST and proportion method (indirect) DST. 778 samples (31.8%) were Mycobacterium tuberculosis culture-positive. Compared to conventional MODS the sensitivity, specificity, positive, and negative predictive values (95% confidence intervals) of the MODS Kit were 99.3% (98.3–99.8%), 98.3% (97.5–98.8%), 95.8% (94.0–97.1%), and 99.7% (99.3–99.9%). Median (interquartile ranges) time to culture-positivity (and rifampicin and isoniazid DST) was 10 (9–13) days for conventional MODS and 8.5 (7–11) for MODS Kit (p<0.01). Direct rifampicin and isoniazid DST in MODS kit was almost universally concordant with conventional MODS (97.9% agreement, 665/679 evaluable samples) and reference indirect DST (97.9% agreement, 687/702 evaluable samples). Conclusions MODS kit delivers performance indistinguishable from conventional MODS and offers a convenient, affordable alternative with enhanced safety from the sealing silicone lid. The availability in the marketplace of this platform, which conforms to European standards (CE-marked), readily repurposed for second-line DST in the near future, provides a fresh opportunity for improving equity of access to TB diagnosis and first and second-line DST in settings where the need is greatest. PMID:25225802

A field evaluation of the Hardy TB MODS Kit™ for the rapid phenotypic diagnosis of tuberculosis and multi-drug resistant tuberculosis.

PubMed

Martin, Laura; Coronel, Jorge; Faulx, Dunia; Valdez, Melissa; Metzler, Mutsumi; Crudder, Chris; Castillo, Edith; Caviedes, Luz; Grandjean, Louis; Rodriguez, Mitzi; Friedland, Jon S; Gilman, Robert H; Moore, David A J

2014-01-01

Even though the WHO-endorsed, non-commercial MODS assay offers rapid, reliable TB liquid culture and phenotypic drug susceptibility testing (DST) at lower cost than any other diagnostic, uptake has been patchy. In part this reflects misperceptions about in-house assay quality assurance, but user convenience of one-stop procurement is also important. A commercial MODS kit was developed by Hardy Diagnostics (Santa Maria, CA, USA) with PATH (Seattle, WA, USA) to facilitate procurement, simplify procedures through readymade media, and enhance safety with a sealing silicone plate lid. Here we report the results from a large-scale field evaluation of the MODS kit in a government service laboratory. 2446 sputum samples were cultured in parallel in Lowenstein-Jensen (LJ), conventional MODS and in the MODS kit. MODS kit DST was compared with conventional MODS (direct) DST and proportion method (indirect) DST. 778 samples (31.8%) were Mycobacterium tuberculosis culture-positive. Compared to conventional MODS the sensitivity, specificity, positive, and negative predictive values (95% confidence intervals) of the MODS Kit were 99.3% (98.3-99.8%), 98.3% (97.5-98.8%), 95.8% (94.0-97.1%), and 99.7% (99.3-99.9%). Median (interquartile ranges) time to culture-positivity (and rifampicin and isoniazid DST) was 10 (9-13) days for conventional MODS and 8.5 (7-11) for MODS Kit (p<0.01). Direct rifampicin and isoniazid DST in MODS kit was almost universally concordant with conventional MODS (97.9% agreement, 665/679 evaluable samples) and reference indirect DST (97.9% agreement, 687/702 evaluable samples). MODS kit delivers performance indistinguishable from conventional MODS and offers a convenient, affordable alternative with enhanced safety from the sealing silicone lid. The availability in the marketplace of this platform, which conforms to European standards (CE-marked), readily repurposed for second-line DST in the near future, provides a fresh opportunity for improving equity of access to TB diagnosis and first and second-line DST in settings where the need is greatest.

Conceptual design of the 7 megawatt Mod-5B wind turbine generator

NASA Technical Reports Server (NTRS)

Douglas, R. R.

1982-01-01

Similar to MOD-2, the MOD-5B wind turbine generator system is designed for the sole purpose of providing electrical power for distribution by a major utility network. The objectives of the MOD-2 and MOD-5B programs are essentially identical with one important exception; the cost-of-electricity (COE) target is reduced from 4 cent/Kwhr on MOD-2 to 3 cent/Kwhr on MOD-5B, based on mid 1977 dollars and large quantity production. The MOD-5B concept studies and eventual concept selection confirmed that the program COE targets could not only be achieved but substantially bettered. Starting from the established MOD-2 technology as a base, this achievement resulted from a combination of concept changes, size changes, and design refinements. The result of this effort is a wind turbine system that can compete with conventional power generation over significant geographical areas, increasing commercial market potential by an order of magnitude.

HMM-ModE: implementation, benchmarking and validation with HMMER3

PubMed Central

2014-01-01

Background HMM-ModE is a computational method that generates family specific profile HMMs using negative training sequences. The method optimizes the discrimination threshold using 10 fold cross validation and modifies the emission probabilities of profiles to reduce common fold based signals shared with other sub-families. The protocol depends on the program HMMER for HMM profile building and sequence database searching. The recent release of HMMER3 has improved database search speed by several orders of magnitude, allowing for the large scale deployment of the method in sequence annotation projects. We have rewritten our existing scripts both at the level of parsing the HMM profiles and modifying emission probabilities to upgrade HMM-ModE using HMMER3 that takes advantage of its probabilistic inference with high computational speed. The method is benchmarked and tested on GPCR dataset as an accurate and fast method for functional annotation. Results The implementation of this method, which now works with HMMER3, is benchmarked with the earlier version of HMMER, to show that the effect of local-local alignments is marked only in the case of profiles containing a large number of discontinuous match states. The method is tested on a gold standard set of families and we have reported a significant reduction in the number of false positive hits over the default HMM profiles. When implemented on GPCR sequences, the results showed an improvement in the accuracy of classification compared with other methods used to classify the familyat different levels of their classification hierarchy. Conclusions The present findings show that the new version of HMM-ModE is a highly specific method used to differentiate between fold (superfamily) and function (family) specific signals, which helps in the functional annotation of protein sequences. The use of modified profile HMMs of GPCR sequences provides a simple yet highly specific method for classification of the family, being able to predict the sub-family specific sequences with high accuracy even though sequences share common physicochemical characteristics between sub-families. PMID:25073805

Effect of milk replacer feeding rate and functional fatty acids on dairy calf performance and digestion of nutrients.

PubMed

Hill, T M; Quigley, J D; Suarez-Mena, F X; Bateman, H G; Schlotterbeck, R L

2016-08-01

Calves fed large amounts of milk replacer (MR) gain more body weight preweaning than calves fed less MR; however, postweaning growth may be reduced because of impaired digestion of nutrients. This was explored in the current research, as was the inclusion of functional fatty acids (NT) that could ameliorate some poor growth and digestion issues in calves fed large amounts of MR. Two MR rates [moderate (MOD) or aggressive (AGG)] with and without NT were compared using 48 male Holstein calves initially 3d old (43±1.5kg of body weight) randomly assigned to treatments. The MOD rate was fed at 0.66kg of dry matter (DM) for 49d. The AGG rate was fed for 4d at 0.66kg of DM, 4d at 0.96kg of DM, then 34d at 1.31kg of DM, followed by 0.66kg of DM for the last 7d. Calves were completely weaned at 49d. The MR contained 27% crude protein and 17% fat. The textured starter was 20% crude protein. Starter and water were fed free-choice for the first 56d when calves were housed in individual pens. From 56 to 112d, calves were grouped (4 calves/pen), maintaining the same MR rate and NT treatments, and fed starter blended with 5% chopped grass hay free-choice with free-choice water. Digestibility was estimated from fecal collections made on d 19 to 23, 40 to 44, and 52 to 56. Data were analyzed as a completely randomized design with a factorial arrangement of MR rate and NT using repeated measures with a mixed procedure. Fiber and starch digestion increased with age and was lower for AGG versus MOD. Calf average daily gain and hip width change were greater before approximately 6wk of age for AGG versus MOD, but this was reversed from approximately 6 to 16wk. Calves fed AGG had lower average daily gain per unit intake of DM, crude protein, and metabolizable energy from 8 to 16wk than calves fed MOD. Preweaning starter intake was less for calves fed AGG versus MOD. Calves fed AGG had greater body weight gain than MOD over 112d, but hip width change did not differ. Feeding NT improved digestibility of organic matter, DM, neutral detergent fiber, and acid detergent fiber (over 50% improvement for neutral detergent fiber and acid detergent fiber), which resulted in 10.7kg (13%) more body weight gain and 1.4cm (16%) more hip width change over 112d. This was a greater improvement in growth than the difference in AGG and MOD programs over 112d. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

In Vitro and in Vivo Characterization of MOD-4023, a Long-Acting Carboxy-Terminal Peptide (CTP)-Modified Human Growth Hormone.

PubMed

Hershkovitz, Oren; Bar-Ilan, Ahuva; Guy, Rachel; Felikman, Yana; Moschcovich, Laura; Hwa, Vivian; Rosenfeld, Ron G; Fima, Eyal; Hart, Gili

2016-02-01

MOD-4023 is a novel long-acting version of human growth hormone (hGH), containing the carboxy-terminal peptide (CTP) of human chorionic gonadotropin (hCG). MOD-4023 is being developed as a treatment for adults and children with growth hormone deficiency (GHD), which would require fewer injections than currently available GH formulations and thus reduce patient discomfort and increase compliance. This study characterizes MOD-4023's binding affinities for the growth hormone receptor, as well as the pharmacokinetic and pharmacodynamics, toxicology, and safety profiles of repeated dosing of MOD-4023 in Sprague-Dawley rats and Rhesus monkeys. Although MOD-4023 exhibited reduced in vitro potency and lower affinity to the GH receptor than recombinant hGH (rhGH), administration of MOD-4023 every 5 days in rats and monkeys resulted in exposure comparable to daily rhGH, and the serum half-life of MOD-4023 was significantly longer. Repeated administration of MOD-4023 led to elevated levels of insulin-like growth factor 1 (IGF-1), and twice-weekly injections of MOD-4023 resulted in larger increase in weight gain with fewer injections and a lower accumulative hGH dose. Thus, the increased half-life of MOD-4023 in comparison to hGH may increase the frequency of protein-receptor interactions and compensate for its decreased in vitro potency. MOD-4023 was found to be well-tolerated in rats and monkeys, with minimal adverse events, suggesting an acceptable safety profile. These results provide a basis for the continued clinical development of MOD-4023 as a novel treatment of GHD in children and adults.

The General Electric MOD-1 wind turbine generator program

NASA Technical Reports Server (NTRS)

Poor, R. H.; Hobbs, R. B.

1979-01-01

The design, fabrication, installation and checkout of MOD-1, a megawatt class wind turbine generator which generates utility grade electrical power, is described. A MOD-1/MOD-1A tradeoff study is discussed.

Simple Pendulum Determination of the Gravitational Constant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parks, Harold V.; Sandia National Laboratories, Albuquerque, New Mexico 87185; Faller, James E.

We determined the Newtonian constant of gravitation G by interferometrically measuring the change in spacing between two free-hanging pendulum masses caused by the gravitational field from large tungsten source masses. We find a value for G of (6.672 34{+-}0.000 14)x10{sup -11} m{sup 3} kg{sup -1} s{sup -2}. This value is in good agreement with the 1986 Committee on Data for Science and Technology (CODATA) value of (6.672 59{+-}0.000 85)x10{sup -11} m{sup 3} kg{sup -1} s{sup -2}[Rev. Mod. Phys. 59, 1121 (1987)] but differs from some more recent determinations as well as the latest CODATA recommendation of (6.674 28{+-}0.000 67)x10{sup -11}more » m{sup 3} kg{sup -1} s{sup -2}[Rev. Mod. Phys. 80, 633 (2008)].« less

Improved Controls for Fusion RF Systems. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Casey, Jeffrey A.

2011-11-08

We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way thatmore » they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration.« less

A framework for cumulative risk assessment in the 21st century.

PubMed

Moretto, Angelo; Bachman, Ammie; Boobis, Alan; Solomon, Keith R; Pastoor, Timothy P; Wilks, Martin F; Embry, Michelle R

2017-02-01

The ILSI Health and Environmental Sciences Institute (HESI) has developed a framework to support a transition in the way in which information for chemical risk assessment is obtained and used (RISK21). The approach is based on detailed problem formulation, where exposure drives the data acquisition process in order to enable informed decision-making on human health safety as soon as sufficient evidence is available. Information is evaluated in a transparent and consistent way with the aim of optimizing available resources. In the context of risk assessment, cumulative risk assessment (CRA) poses additional problems and questions that can be addressed using the RISK21 approach. The focus in CRA to date has generally been on chemicals that have common mechanisms of action. Recently, concern has also been expressed about chemicals acting on multiple pathways that lead to a common health outcome, and non-chemical other conditions (non-chemical stressors) that can lead to or modify a common outcome. Acknowledging that CRAs, as described above, are more conceptually, methodologically and computationally complex than traditional single-stressor risk assessments, RISK21 further developed the framework for implementation of workable processes and procedures for conducting assessments of combined effects from exposure to multiple chemicals and non-chemical stressors. As part of the problem formulation process, this evidence-based framework allows the identification of the circumstances in which it is appropriate to conduct a CRA for a group of compounds. A tiered approach is then proposed, where additional chemical stressors and/or non-chemical modulating factors (ModFs) are considered sequentially. Criteria are provided to facilitate the decision on whether or not to include ModFs in the formal quantitative assessment, with the intention to help focus the use of available resources to have the greatest potential to protect public health.

Community Resilience: Increasing Public Understanding of Risk and Vulnerability to Natural Hazards through Informal Education

NASA Astrophysics Data System (ADS)

Salna, E.

2017-12-01

The Extreme Events Institute's (EEI) International Hurricane Research Center (IHRC) at Florida International University (FIU) in Miami, Florida, as a NOAA Weather-Ready Nation Ambassador, is dedicated to make South Florida, Ready, Responsive and Resilient. IHRC with funding from the Florida Division of Emergency Management (FDEM) has developed several museum exhibits and events. This includes the hands-on FIU Wall of Wind exhibit for the National Building Museum in Washington, DC, the Frost Science Museum in Miami, Florida, and the Museum of Discovery and Science (MODS) in Fort Lauderdale, Florida. The exhibit teaches the public about hurricane wind engineering research, enhanced building codes, and the importance of protecting your home's windows and doors with code-approved shutters. In addition, IHRC and MODS facilitate Eye of the Storm, a free-of-charge, community event with interactive hurricane science, and preparedness activities, including the entertaining Owlie Skywarn live theater show and live air cannon missile impact demonstrations. This annual event includes many local, state and federal partners, including NOAA and NWS. The IHRC also developed the FIU Wall of Wind Mitigation Challenge. As the next generation of engineers to address natural hazards and extreme weather, this STEM education event features a competition between high school teams to develop innovative wind mitigation concepts and real-life human safety and property protection solutions. IHRC and MODS are also developing a new exhibit of a Hazard/Risk Equation that will "come to life," through virtual reality (VR) technology in a state-of-the art 7D theater. The exhibit will provide a better public understanding of how changes in exposures and vulnerabilities will determine whether a community experiences an emergency, disaster or catastrophe. It will raise public consciousness and drive home the point that communities need not passively accept natural hazard risks. Ultimately, if we raise their understanding, we may raise their support for Disaster Risk Reduction and then voice that support to their local government officials and policy-makers. The goal and end-result is improved community resilience. This is especially relevant with Miami being part of the Rockefeller Foundation's 100 Resilient Cities Initiative.

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Farrell, R.; Hindes, C.; Battista, R.; Connelly, M.; Cronin, M.; Howarth, R.; Donahue, A.; Slate, E.; Stotts, R.; Lacy, R.

1988-01-01

The study of high power kinematic Stirling engines for transportation use, testing of Mod I and Mod II Stirling engines, and component development activities are summarized. Mod II development testing was performed to complete the development of the basic engine and begin characterization of performance. Mod I engines were used for Mod II component development and to obtain independent party (U.S. Air Force) evaluation of Stirling engine vehicle performance.

Diagnosis of Pulmonary Tuberculosis in HIV-Positive Patients by Microscopic Observation Drug Susceptibility Assay ▿

PubMed Central

Ha, Dang Thi Minh; Lan, Nguyen Thi Ngoc; Kiet, Vo Sy; Wolbers, Marcel; Hang, Hoang Thi Thanh; Day, Jeremy; Hien, Nguyen Quang; Tien, Nguyen Anh; An, Pham Thuy; Anh, Truong Thi; Oanh, Do Thi Tuong; Hoa, Chau Luong; Chau, Nguyen Thi Minh; Hai, Nguyen Ngoc; Binh, Ngo Thanh; Ngoc, Le Hong; Phuong, Doan Thanh; Quyet, Tran Van; Tuyen, Nguyen Thi Bich; Ha, Vo Thi; Nho, Nguyen Thi; Hoa, Dai Viet; Anh, Phan Thi Hoang; Dung, Nguyen Huy; Farrar, Jeremy; Caws, Maxine

2010-01-01

The microscopic observation drug susceptibility assay (MODS) is a novel and promising test for the early diagnosis of tuberculosis (TB). We evaluated the MODS assay for the early diagnosis of TB in HIV-positive patients presenting to Pham Ngoc Thach Hospital for Tuberculosis and Lung Diseases in southern Vietnam. A total of 738 consecutive sputum samples collected from 307 HIV-positive individuals suspected of TB were tested by smear, MODS, and the mycobacteria growth indicator tube method (MGIT). The diagnostic sensitivity and specificity of MODS compared to the microbiological gold standard (either smear or MGIT) were 87 and 93%, respectively. The sensitivities of smear, MODS, and MGIT were 57, 71, and 75%, respectively, against clinical gold standard (MODS versus smear, P < 0.001; MODS versus MGIT, P = 0.03). The clinical gold standard was defined as patients who had a clinical examination and treatment consistent with TB, with or without microbiological confirmation. For the diagnosis of smear-negative patients, the sensitivities of MODS and MGIT were 38 and 45%, respectively (P = 0.08). The median times to detection using MODS and MGIT were 8 and 11 days, respectively, and they were 11 and 17 days, respectively, for smear-negative samples. The original bacterial/fungal contamination rate of MODS was 1.1%, while it was 2.6% for MGIT. The cross-contamination rate of MODS was 4.7%. In conclusion, MODS is a sensitive, specific, and rapid test that is appropriate for the detection of HIV-associated TB; its cost and ease of use make it particularly useful in resource-limited settings. PMID:20926704

Model Development for VDE Computations in NIMROD

NASA Astrophysics Data System (ADS)

Bunkers, K. J.; Sovinec, C. R.

2017-10-01

Vertical displacement events (VDEs) and the disruptions associated with them have potential for causing considerable physical damage to ITER and other tokamak experiments. We report on simulations of generic axisymmetric VDEs and a vertically unstable case from Alcator C-MOD using the NIMROD code. Previous calculations have been done with closures for heat flux and viscous stress. Initial calculations show that halo current width is dependent on temperature boundary conditions, and so transport together with plasma-surface interaction may play a role in determining halo currents in experiments. The behavior of VDEs with Braginskii thermal conductivity and viscosity closures and Spitzer-like resistivity are investigated for both the generic axisymmetric VDE case and the C-MOD case. This effort is supported by the U.S. Dept. of Energy, Award Numbers DE-FG02-06ER54850 and DE-FC02-08ER54975.

Cement Thickness of Inlay Restorations Made of Lithium Disilicate, Polymer-Infiltrated Ceramic and Nano-Ceramic CAD/CAM Materials Evaluated Using 3D X-Ray Micro-Computed Tomography.

PubMed

Uzgur, Recep; Ercan, Ertuğrul; Uzgur, Zeynep; Çolak, Hakan; Yalçın, Muhammet; Özcan, Mutlu

2016-08-12

To evaluate the marginal and internal cement thicknesses of inlay restorations made of various CAD/CAM materials using 3D X-ray micro-computed tomography (micro-CT) technique. Caries-free extracted mandibular molars (N = 30) with similar size were randomly assigned to three groups (N = 10 per group). Mesio-occlusal-distal (MOD) cavities were prepared, and inlay restorations were obtained by milling out CAD/CAM materials namely, (a) IPS: monolithic lithium disilicate (control), (b) VE: polymer-infiltrated ceramic, and (c) CS: nano-ceramic using a CAM unit. Marginal and internal cement thicknesses were measured using 3D micro-CT. Data were analyzed using 1-way ANOVA and Tukey's tests (alpha = 0.05). The mean marginal and internal cement thickness were not significant in all inlay materials (p > 0.05). Mean marginal cement thickness (μm) was the lowest for the IPS group (67.54 ± 10.16) followed by VE (84.09 ± 3.94) and CS (95.18 ± 10.58) (p > 0.05). The internal cement thickness (μm) was the lowest in the CS group (54.85 ± 6.94) followed by IPS (60.58 ± 9.22) and VE (77.53 ± 12.13) (p > 0.05). Marginal and internal cement thicknesses of MOD inlays made of monolithic lithium disilicate, polymer-infiltrated ceramic, and nano-ceramic CAD/CAM materials were similar and all less than 100 μm, which could be considered clinically acceptable. MOD inlays made of different CAD/CAM materials presented similar cement thickness, less than 100 μm. © 2016 by the American College of Prosthodontists.

Inlay-retained cantilever fixed dental prostheses to substitute a single premolar: impact of zirconia framework design after dynamic loading.

PubMed

Shahin, Ramez; Tannous, Fahed; Kern, Matthias

2014-08-01

The purpose of this in-vitro study was to evaluate the influence of the framework design on the durability of inlay-retained cantilever fixed dental prostheses (IR-FDPs), made from zirconia ceramic, after artificial ageing. Forty-eight caries-free human premolars were prepared as abutments for all-ceramic cantilevered IR-FDPs using six framework designs: occlusal-distal (OD) inlay, OD inlay with an oral retainer wing, OD inlay with two retainer wings, mesial-occlusal-distal (MOD) inlay, MOD inlay with an oral retainer ring, and veneer partial coping with a distal box (VB). Zirconia IR-FDPs were fabricated via computer-aided design/computer-aided manufacturing (CAD/CAM) technology. The bonding surfaces were air-abraded (50 μm alumina/0.1 MPa), and the frameworks were bonded with adhesive resin cement. Specimens were stored for 150 d in a 37°C water bath during which they were thermocycled between 5 and 55°C for 37,500 cycles; thereafter, they were exposed to 600,000 cycles of dynamic loading with a 5-kg load in a chewing simulator. All surviving specimens were loaded onto the pontic and tested until failure using a universal testing machine. The mean failure load of the groups ranged from 260.8 to 746.7 N. Statistical analysis showed that both MOD groups exhibited significantly higher failure loads compared with the other groups (i.e. the three OD groups and the VB group) and that there was no significant difference in the failure load among the OD groups and the VB group. In conclusion, zirconia IR-FDPs with a modified design exhibited promising failure modes. © 2014 Eur J Oral Sci.

R-modafinil attenuates nicotine-taking and nicotine-seeking behavior in alcohol-preferring rats.

PubMed

Wang, Xiao-Fei; Bi, Guo-Hua; He, Yi; Yang, Hong-Ju; Gao, Jun-Tao; Okunola-Bakare, Oluyomi M; Slack, Rachel D; Gardner, Eliot L; Xi, Zheng-Xiong; Newman, Amy Hauck

2015-06-01

(±)-Modafinil (MOD) is used clinically for the treatment of sleep disorders and has been investigated as a potential medication for the treatment of psychostimulant addiction. However, the therapeutic efficacy of (±)-MOD for addiction is inconclusive. Herein we used animal models of self-administration and in vivo microdialysis to study the pharmacological actions of R-modafinil (R-MOD) and S-modafinil (S-MOD) on nicotine-taking and nicotine-seeking behavior, and mechanisms underlying such actions. We found that R-MOD is more potent and effective than S-MOD in attenuating nicotine self-administration in Long-Evans rats. As Long-Evans rats did not show a robust reinstatement response to nicotine, we used alcohol-preferring rats (P-rats) that display much higher reinstatement responses to nicotine than Long-Evans rats. We found that R-MOD significantly inhibited intravenous nicotine self-administration, nicotine-induced reinstatement, and nicotine-associated cue-induced drug-seeking behavior in P-rats. R-MOD alone neither sustained self-administration in P-rats previously self-administering nicotine nor reinstated extinguished nicotine-seeking behavior. The in vivo brain microdialysis assays demonstrated that R-MOD alone produced a slow-onset moderate increase in extracellular DA. Pretreatment with R-MOD dose-dependently blocked nicotine-induced dopamine (DA) release in the nucleus accumbens (NAc) in both naive and nicotine self-administrating rats, suggesting a DA-dependent mechanism underlying mitigation of nicotine's effects. In conclusion, the present findings support further investigation of R-MOD for treatment of nicotine dependence in humans.

R-Modafinil Attenuates Nicotine-Taking and Nicotine-Seeking Behavior in Alcohol-Preferring Rats

PubMed Central

Wang, Xiao-Fei; Bi, Guo-Hua; He, Yi; Yang, Hong-Ju; Gao, Jun-Tao; Okunola-Bakare, Oluyomi M; Slack, Rachel D; Gardner, Eliot L; Xi, Zheng-Xiong; Newman, Amy Hauck

2015-01-01

(±)-Modafinil (MOD) is used clinically for the treatment of sleep disorders and has been investigated as a potential medication for the treatment of psychostimulant addiction. However, the therapeutic efficacy of (±)-MOD for addiction is inconclusive. Herein we used animal models of self-administration and in vivo microdialysis to study the pharmacological actions of R-modafinil (R-MOD) and S-modafinil (S-MOD) on nicotine-taking and nicotine-seeking behavior, and mechanisms underlying such actions. We found that R-MOD is more potent and effective than S-MOD in attenuating nicotine self-administration in Long–Evans rats. As Long–Evans rats did not show a robust reinstatement response to nicotine, we used alcohol-preferring rats (P-rats) that display much higher reinstatement responses to nicotine than Long–Evans rats. We found that R-MOD significantly inhibited intravenous nicotine self-administration, nicotine-induced reinstatement, and nicotine-associated cue-induced drug-seeking behavior in P-rats. R-MOD alone neither sustained self-administration in P-rats previously self-administering nicotine nor reinstated extinguished nicotine-seeking behavior. The in vivo brain microdialysis assays demonstrated that R-MOD alone produced a slow-onset moderate increase in extracellular DA. Pretreatment with R-MOD dose-dependently blocked nicotine-induced dopamine (DA) release in the nucleus accumbens (NAc) in both naive and nicotine self-administrating rats, suggesting a DA-dependent mechanism underlying mitigation of nicotine's effects. In conclusion, the present findings support further investigation of R-MOD for treatment of nicotine dependence in humans. PMID:25613829

Role of endocortical contouring methods on precision of HR-pQCT-derived cortical micro-architecture in postmenopausal women and young adults.

PubMed

Kawalilak, C E; Johnston, J D; Cooper, D M L; Olszynski, W P; Kontulainen, S A

2016-02-01

Precision errors of cortical bone micro-architecture from high-resolution peripheral quantitative computed tomography (pQCT) ranged from 1 to 16 % and did not differ between automatic or manually modified endocortical contour methods in postmenopausal women or young adults. In postmenopausal women, manually modified contours led to generally higher cortical bone properties when compared to the automated method. First, the objective of the study was to define in vivo precision errors (coefficient of variation root mean square (CV%RMS)) and least significant change (LSC) for cortical bone micro-architecture using two endocortical contouring methods: automatic (AUTO) and manually modified (MOD) in two groups (postmenopausal women and young adults) from high-resolution pQCT (HR-pQCT) scans. Second, it was to compare precision errors and bone outcomes obtained with both methods within and between groups. Using HR-pQCT, we scanned twice the distal radius and tibia of 34 postmenopausal women (mean age ± SD 74 ± 7 years) and 30 young adults (27 ± 9 years). Cortical micro-architecture was determined using AUTO and MOD contour methods. CV%RMS and LSC were calculated. Repeated measures and multivariate ANOVA were used to compare mean CV% and bone outcomes between the methods within and between the groups. Significance was accepted at P < 0.05. CV%RMS ranged from 0.9 to 16.3 %. Within-group precision did not differ between evaluation methods. Compared to young adults, postmenopausal women had better precision for radial cortical porosity (precision difference 9.3 %) and pore volume (7.5 %) with MOD. Young adults had better precision for cortical thickness (0.8 %, MOD) and tibial cortical density (0.2 %, AUTO). In postmenopausal women, MOD resulted in 0.2-54 % higher values for most cortical outcomes, as well as 6-8 % lower radial and tibial cortical BMD and 2 % lower tibial cortical thickness. Results suggest that AUTO and MOD endocortical contour methods provide comparable repeatability. In postmenopausal women, manual modification of endocortical contours led to generally higher cortical bone properties when compared to the automated method, while no between-method differences were observed in young adults.

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Antonelli, M. (Editor)

1983-01-01

Mod I engine testing and test results, the test of a Mod I engine in the United States, Mod I engine characterization and analysis, Mod I Transient Test Bed fuel economy, Mod I-A engine performance are discussed. Stirling engine reference engine manufacturing and reduced size studies, components and subsystems, and the study and test of low-cost casting alloys are also covered. The overall program philosophy is outlined, and data and results are presented.

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Rohdenburg, C.; Vatsky, A.; Antonelli, M. (Editor)

1983-01-01

Activities performed on Mod I engine testing and test results, testing of the Mod I engine in the United States, Mod I engine characterization and analyses, Mod I Transient Test Bed fuel economy, upgraded Mod I performance and testing, Stirling engine reference engine manufacturing and reduced size studied, components and subsystems, and the study and test of low cost casting alloys are summarized. The overall program philosophy is outlined, and data and results are presented.

Validation of the MODIS MOD21 and MOD11 land surface temperature and emissivity products in an arid area of Northwest China

NASA Astrophysics Data System (ADS)

Li, H.; Yang, Y.; Yongming, D.; Cao, B.; Qinhuo, L.

2017-12-01

Land surface temperature (LST) is a key parameter for hydrological, meteorological, climatological and environmental studies. During the past decades, many efforts have been devoted to the establishment of methodology for retrieving the LST from remote sensing data and significant progress has been achieved. Many operational LST products have been generated using different remote sensing data. MODIS LST product (MOD11) is one of the most commonly used LST products, which is produced using a generalized split-window algorithm. Many validation studies have showed that MOD11 LST product agrees well with ground measurements over vegetated and inland water surfaces, however, large negative biases of up to 5 K are present over arid regions. In addition, land surface emissivity of MOD11 are estimated by assigning fixed emissivities according to a land cover classification dataset, which may introduce large errors to the LST product due to misclassification of the land cover. Therefore, a new MODIS LSE&E product (MOD21) is developed based on the temperature emissivity separation (TES) algorithm, and the water vapor scaling (WVS) method has also been incorporated into the MODIS TES algorithm for improving the accuracy of the atmospheric correction. The MOD21 product will be released with MODIS collection 6 Tier-2 land products in 2017. Due to the MOD21 products are not available right now, the MODTES algorithm was implemented including the TES and WVS methods as detailed in the MOD21 Algorithm Theoretical Basis Document. The MOD21 and MOD11 C6 LST products are validated using ground measurements and ASTER LST products collected in an arid area of Northwest China during the Heihe Watershed Allied Telemetry Experimental Research (HiWATER) experiment. In addition, lab emissivity spectra of four sand dunes in the Northwest China are also used to validate the MOD21 and MOD11 emissivity products.

Long-Acting C-Terminal Peptide-Modified hGH (MOD-4023): Results of a Safety and Dose-Finding Study in GHD Children.

PubMed

Zelinska, Nataliya; Iotova, Violeta; Skorodok, Julia; Malievsky, Oleg; Peterkova, Valentina; Samsonova, Lubov; Rosenfeld, Ron G; Zadik, Zvi; Jaron-Mendelson, Michal; Koren, Ronit; Amitzi, Leanne; Raduk, Dmitri; Hershkovitz, Oren; Hart, Gili

2017-05-01

Daily injections are required for growth hormone (GH) replacement therapy, which may cause low compliance as a result of inconvenience and distress in patients. C-terminal peptide-modified human GH (MOD-4023) is developed for once-a-week dosing regimen in GH-deficient (GHD) adults and children. The present trial was a safety and dose-finding study for weekly MOD-4023 in GHD children. A multicenter, open-label, randomized, controlled phase 2 study in children with GHD, evaluating the safety, tolerability, pharmacokinetics/pharmacodynamics, and efficacy of three different weekly MOD-4023 doses, compared with daily recombinant human GH (r-hGH). The trial was conducted in 14 endocrinology centers in Europe. Fifty-three prepubertal children with GHD completed 12 months of treatment with either MOD-4023 (N = 42) or r-hGH (N = 11). C-terminal peptide-modified hGH (MOD-4023) was administered weekly at a dose of either 0.25, 0.48, or 0.66 mg/kg/wk and compared with daily hGH at a dose of 0.24 mg/kg/wk. MOD-4023 showed an estimated half-life approximately fivefold to 10-fold longer when compared with daily r-hGH. Insulin-like growth factor (IGF)-I and IGF-binding peptide 3 showed a dose-dependent increase during MOD-4023 treatment. IGF-I standard deviation score for MOD-4023 did not exceed +2. All MOD-4023 cohorts demonstrated adequate catch-up growth. The 0.66 mg/kg/wk dose demonstrated efficacy closest to daily r-hGH. No serious adverse events were observed during MOD-4023 treatment, and its tolerability was consistent with known properties of r-hGH. This study confirms the long-acting properties of MOD-4023 and shows a promising safety and tolerability profile. This provides support for initiation of a phase 3 study in GHD children using a single weekly injection of MOD-4023. Copyright © 2017 by the Endocrine Society

Mod-1 Wind Turbine at Boone, North Carolina

NASA Image and Video Library

1979-06-21

A Mod-1 2000-kilowatt wind turbine designed by National Aeronautics and Space Administration (NASA) Lewis Research Center and constructed in Boone, North Carolina. The wind turbine program was a joint program between NASA and the Energy Research and Development Administration (ERDA) during the 1970s to develop less expensive forms of energy. NASA Lewis was assigned the responsibility of developing large horizontal-axis wind turbines. The program included a series of increasingly powerful wind turbines, designated: Mod-0A, Mod-1, WTS-4, and Mod-5. The program’s first device was a Mod-0 100-kilowatt wind turbine test bed at NASA’s Plum Brook Station. There were four Mod-0A 200-kilowatt turbines built in New Mexico, Hawaii, Puerto Rico, and Rhode Island. The 2000-kilowatt wind turbine in North Carolina, seen here, was the only Mod-1 machine constructed. The two-bladed, 200-foot diameter device was built in May 1979 and began operation that September. The Mod-1 turbine performed exceedingly well and was fully integrated into the local power grid. NASA researchers also used the North Carolina device to study its effect on noise and television transmission.

TEMPEST: A three-dimensional time-dependent computer program for hydrothermal analysis: Volume 1, Numerical methods and input instructions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trent, D.S.; Eyler, L.L.; Budden, M.J.

This document describes the numerical methods, current capabilities, and the use of the TEMPEST (Version L, MOD 2) computer program. TEMPEST is a transient, three-dimensional, hydrothermal computer program that is designed to analyze a broad range of coupled fluid dynamic and heat transfer systems of particular interest to the Fast Breeder Reactor thermal-hydraulic design community. The full three-dimensional, time-dependent equations of motion, continuity, and heat transport are solved for either laminar or turbulent fluid flow, including heat diffusion and generation in both solid and liquid materials. 10 refs., 22 figs., 2 tabs.

Mod 1 ICS TI Report: ICS Conversion of a 140% HPGe Detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bounds, John Alan

This report evaluates the Mod 1 ICS, an electrically cooled 140% HPGe detector. It is a custom version of the ORTEC Integrated Cooling System (ICS) modified to make it more practical for us to use in the field. Performance and operating characteristics of the Mod 1 ICS are documented, noting both pros and cons. The Mod 1 ICS is deemed a success. Recommendations for a Mod 2 ICS, a true field prototype, are provided.

ModFOLD6: an accurate web server for the global and local quality estimation of 3D protein models.

PubMed

Maghrabi, Ali H A; McGuffin, Liam J

2017-07-03

Methods that reliably estimate the likely similarity between the predicted and native structures of proteins have become essential for driving the acceptance and adoption of three-dimensional protein models by life scientists. ModFOLD6 is the latest version of our leading resource for Estimates of Model Accuracy (EMA), which uses a pioneering hybrid quasi-single model approach. The ModFOLD6 server integrates scores from three pure-single model methods and three quasi-single model methods using a neural network to estimate local quality scores. Additionally, the server provides three options for producing global score estimates, depending on the requirements of the user: (i) ModFOLD6_rank, which is optimized for ranking/selection, (ii) ModFOLD6_cor, which is optimized for correlations of predicted and observed scores and (iii) ModFOLD6 global for balanced performance. The ModFOLD6 methods rank among the top few for EMA, according to independent blind testing by the CASP12 assessors. The ModFOLD6 server is also continuously automatically evaluated as part of the CAMEO project, where significant performance gains have been observed compared to our previous server and other publicly available servers. The ModFOLD6 server is freely available at: http://www.reading.ac.uk/bioinf/ModFOLD/. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Modafinil Activates Phasic Dopamine Signaling in Dorsal and Ventral Striata

PubMed Central

Bobak, Martin J.; Weber, Matthew W.; Doellman, Melissa A.; Schuweiler, Douglas R.; Athens, Jeana M.; Juliano, Steven A.

2016-01-01

Modafinil (MOD) exhibits therapeutic efficacy for treating sleep and psychiatric disorders; however, its mechanism is not completely understood. Compared with other psychostimulants inhibiting dopamine (DA) uptake, MOD weakly interacts with the dopamine transporter (DAT) and modestly elevates striatal dialysate DA, suggesting additional targets besides DAT. However, the ability of MOD to induce wakefulness is abolished with DAT knockout, conversely suggesting that DAT is necessary for MOD action. Another psychostimulant target, but one not established for MOD, is activation of phasic DA signaling. This communication mode during which burst firing of DA neurons generates rapid changes in extracellular DA, the so-called DA transients, is critically implicated in reward learning. Here, we investigate MOD effects on phasic DA signaling in the striatum of urethane-anesthetized rats with fast-scan cyclic voltammetry. We found that MOD (30–300 mg/kg i.p.) robustly increases the amplitude of electrically evoked phasic-like DA signals in a time- and dose-dependent fashion, with greater effects in dorsal versus ventral striata. MOD-induced enhancement of these electrically evoked amplitudes was mediated preferentially by increased DA release compared with decreased DA uptake. Principal component regression of nonelectrically evoked recordings revealed negligible changes in basal DA with high-dose MOD (300 mg/kg i.p.). Finally, in the presence of the D2 DA antagonist, raclopride, low-dose MOD (30 mg/kg i.p.) robustly elicited DA transients in dorsal and ventral striata. Taken together, these results suggest that activation of phasic DA signaling is an important mechanism underlying the clinical efficacy of MOD. PMID:27733628

DVS-SOFTWARE: An Effective Tool for Applying Highly Parallelized Hardware To Computational Geophysics

NASA Astrophysics Data System (ADS)

Herrera, I.; Herrera, G. S.

2015-12-01

Most geophysical systems are macroscopic physical systems. The behavior prediction of such systems is carried out by means of computational models whose basic models are partial differential equations (PDEs) [1]. Due to the enormous size of the discretized version of such PDEs it is necessary to apply highly parallelized super-computers. For them, at present, the most efficient software is based on non-overlapping domain decomposition methods (DDM). However, a limiting feature of the present state-of-the-art techniques is due to the kind of discretizations used in them. Recently, I. Herrera and co-workers using 'non-overlapping discretizations' have produced the DVS-Software which overcomes this limitation [2]. The DVS-software can be applied to a great variety of geophysical problems and achieves very high parallel efficiencies (90%, or so [3]). It is therefore very suitable for effectively applying the most advanced parallel supercomputers available at present. In a parallel talk, in this AGU Fall Meeting, Graciela Herrera Z. will present how this software is being applied to advance MOD-FLOW. Key Words: Parallel Software for Geophysics, High Performance Computing, HPC, Parallel Computing, Domain Decomposition Methods (DDM)REFERENCES [1]. Herrera Ismael and George F. Pinder, Mathematical Modelling in Science and Engineering: An axiomatic approach", John Wiley, 243p., 2012. [2]. Herrera, I., de la Cruz L.M. and Rosas-Medina A. "Non Overlapping Discretization Methods for Partial, Differential Equations". NUMER METH PART D E, 30: 1427-1454, 2014, DOI 10.1002/num 21852. (Open source) [3]. Herrera, I., & Contreras Iván "An Innovative Tool for Effectively Applying Highly Parallelized Software To Problems of Elasticity". Geofísica Internacional, 2015 (In press)

Multi-channel transport experiments at Alcator C-Mod and comparison with gyrokinetic simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, A. E.; Howard, N. T.; Greenwald, M.

2013-05-15

Multi-channel transport experiments have been conducted in auxiliary heated (Ion Cyclotron Range of Frequencies) L-mode plasmas at Alcator C-Mod [Marmar and Alcator C-Mod Group, Fusion Sci. Technol. 51(3), 3261 (2007)]. These plasmas provide good diagnostic coverage for measurements of kinetic profiles, impurity transport, and turbulence (electron temperature and density fluctuations). In the experiments, a steady sawtoothing L-mode plasma with 1.2 MW of on-axis RF heating is established and density is scanned by 20%. Measured rotation profiles change from peaked to hollow in shape as density is increased, but electron density and impurity profiles remain peaked. Ion or electron heat fluxesmore » from the two plasmas are the same. The experimental results are compared directly to nonlinear gyrokinetic theory using synthetic diagnostics and the code GYRO [Candy and Waltz, J. Comput. Phys. 186, 545 (2003)]. We find good agreement with experimental ion heat flux, impurity particle transport, and trends in the fluctuation level ratio (T(tilde sign){sub e}/T{sub e})/(ñ{sub e}/n{sub e}), but underprediction of electron heat flux. We find that changes in momentum transport (rotation profiles changing from peaked to hollow) do not correlate with changes in particle transport, and also do not correlate with changes in linear mode dominance, e.g., Ion Temperature Gradient versus Trapped Electron Mode. The new C-Mod results suggest that the drives for momentum transport differ from drives for heat and particle transport. The experimental results are inconsistent with present quasilinear models, and the strong sensitivity of core rotation to density remains unexplained.« less

GalMod: A Galactic Synthesis Population Model

NASA Astrophysics Data System (ADS)

Pasetto, Stefano; Grebel, Eva K.; Chiosi, Cesare; Crnojević, Denija; Zeidler, Peter; Busso, Giorgia; Cassarà, Letizia P.; Piovan, Lorenzo; Tantalo, Rosaria; Brogliato, Claudio

2018-06-01

We present a new Galaxy population synthesis Model, GalMod. GalMod is a star-count model featuring an asymmetric bar/bulge as well as spiral arms and related extinction. The model, initially introduced in Pasetto et al., has been here completed with a central bar, a new bulge description, new disk vertical profiles, and several new bolometric corrections. The model can generate synthetic mock catalogs of visible portions of the Milky Way, external galaxies like M31, or N-body simulation initial conditions. At any given time, e.g., at a chosen age of the Galaxy, the model contains a sum of discrete stellar populations, namely the bulge/bar, disk, and halo. These populations are in turn the sum of different components: the disk is the sum of the spiral arms, thin disks, a thick disk, and various gas components, while the halo is the sum of a stellar component, a hot coronal gas, and a dark-matter component. The Galactic potential is computed from these population density profiles and used to generate detailed kinematics by considering up to the first four moments of the collisionless Boltzmann equation. The same density profiles are then used to define the observed color–magnitude diagrams in a user-defined field of view (FoV) from an arbitrary solar location. Several photometric systems have been included and made available online, and no limits on the size of the FoV are imposed thus allowing full-sky simulations, too. Finally, we model the extinction by adopting a dust model with advanced ray-tracing solutions. The model's Web page (and tutorial) can be accessed at www.GalMod.org and support is provided at Galaxy.Model@yahoo.com.

Creating of Central Geospatial Database of the Slovak Republic and Procedures of its Revision

NASA Astrophysics Data System (ADS)

Miškolci, M.; Šafář, V.; Šrámková, R.

2016-06-01

The article describes the creation of initial three dimensional geodatabase from planning and designing through the determination of technological and manufacturing processes to practical using of Central Geospatial Database (CGD - official name in Slovak language is Centrálna Priestorová Databáza - CPD) and shortly describes procedures of its revision. CGD ensures proper collection, processing, storing, transferring and displaying of digital geospatial information. CGD is used by Ministry of Defense (MoD) for defense and crisis management tasks and by Integrated rescue system. For military personnel CGD is run on MoD intranet, and for other users outside of MoD is transmutated to ZbGIS (Primary Geodatabase of Slovak Republic) and is run on public web site. CGD is a global set of geo-spatial information. CGD is a vector computer model which completely covers entire territory of Slovakia. Seamless CGD is created by digitizing of real world using of photogrammetric stereoscopic methods and measurements of objects properties. Basic vector model of CGD (from photogrammetric processing) is then taken out to the field for inspection and additional gathering of objects properties in the whole area of mapping. Finally real-world objects are spatially modeled as a entities of three-dimensional database. CGD gives us opportunity, to get know the territory complexly in all the three spatial dimensions. Every entity in CGD has recorded the time of collection, which allows the individual to assess the timeliness of information. CGD can be utilized for the purposes of geographical analysis, geo-referencing, cartographic purposes as well as various special-purpose mapping and has the ambition to cover the needs not only the MoD, but to become a reference model for the national geographical infrastructure.

GalMod: the last frontier of Galaxy population synthesis models

NASA Astrophysics Data System (ADS)

Pasetto, Stefano; Kollmeier, Juna; Grebel, Eva K.; chiosi, cesare

2018-01-01

We present a novel Galaxy population synthesis model: GalMod (Pasetto et al. 2016, 2017a,b) is the only star-count model featuring an asymmetric bar/bulge as well as spiral arms as directly obtained by applying linear perturbative theory to self-consistent distribution function of the Galaxy stellar populations. Compared to previous literature models (e.g., Besancon, Trilegal), GalMod allows to generate full-sky mock catalogue, M31 surveys and provides a better match to observed Milky Way (MW) stellar fields.The model can generate synthetic mock catalogs of visible portions of the MW, external galaxies like M31, or N-body simulation initial conditions. At any given time, e.g., a chosen age of the Galaxy, the model contains a sum of discrete stellar populations, namely bulge/bar, disk, halo. The disk population is itself the sum of subpopulations: spiral arms, thin disk, thick disk, and gas component, while the halo is modeled as the sum of a stellar component, a hot coronal gas, and a dark matter component. The Galactic potential is computed from these subpopulations' density profiles and used to generate detailed kinematics by considering the first few moments of the Boltzmann collisionless equation for all the stellar subpopulations. The same density profiles are then used to define the observed color-magnitude diagrams within an input field of view from an arbitrary solar location. Several photometric systems have been included and made available on-line, e.g., SDSS, Gaia, 2MASS, HST WFC3, and others. Finally, we model the extinction with advanced ray tracing solutions.The model's web page (and tutorial) can be accessed at www.GalMod.org.

Effect of milk replacer program on calf performance and digestion of nutrients in dairy calves to 4 months of age.

PubMed

Hill, T M; Quigley, J D; Bateman, H G; Suarez-Mena, F X; Dennis, T S; Schlotterbeck, R L

2016-10-01

Calves fed >0.7kg of dry matter from milk replacer (MR) typically have greater growth preweaning but lower growth postweaning. This is partially explained by lower digestibility of starter due to less development of the rumen at and after weaning; however, it is unclear when digestibility matures postweaning to levels typical of mature ruminants. Thus, we fed Holstein calves (initially 2 to 3d of age) 3 MR programs (MOD=0.66kg daily for 39d, and then 0.33kg daily for 3d, n=15 calves; HIMOD=0.88kg daily for 5d, then 1.1kg daily for 23d, then 0.66kg daily for 18d, and then 0.33kg daily for 3d, n=16 calves; HI=0.88kg daily for 5d, then 1.1kg daily for 37d, and then 0.56kg daily for 7d, n=15 calves). The MR consisted of 28% crude protein and 20% fat and was reconstituted to 14% solids and fed at 0630 and 1400 h daily. A 39% starch textured starter (19% crude protein) was fed free-choice for the first 56d of a nursery trial with calves in individual pens. From 56 to 112d, calves were grouped by MR program into pens of 3 to 4 calves and offered a starter with the same ingredient composition blended with 5% chopped grass hay for ad libitum consumption. Digestion was estimated at 11 and 16wk. Measurements in the first and second 56d were analyzed separately in a completely randomized design using repeated measurements when applicable. Preplanned contrasts of MOD versus HIMOD and MOD versus HI were used to separate means. Milk replacer dry matter intake was 26.6, 42.4, and 48.7kg in calves fed MOD, HIMOD, and HI, respectively. Starter intake was less for calves fed HIMOD and HI versus MOD from 3 to 8wk. Efficiency of metabolizable energy and protein used for body weight gain did not differ among programs. During the second 56d, body weight gain and hip width changes were greater for calves fed MOD than HI. Total 112-d body weight gain and total hip width changes were 101.4, 101.3, and 101.7kg, and 9.0, 9.1, and 8.7cm for MOD, HIMOD, and HI, respectively. Digestibility of all nutrients except starch were greater at 16 versus 11wk of age. Digestibility of dry matter, organic matter, neutral detergent fiber, and acid detergent fiber were less for HI versus MOD at 11wk of age explaining much of the why postweaning body weight gain advantages were lost postweaning in calves fed the HI program. Feeding more than 0.66kg of dry matter intake from a MR during the preweaning phase did not increase total body weight or hip width gain from 0 to 4mo of age. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Linear servomotor probe drive system with real-time self-adaptive position control for the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Brunner, D.; Kuang, A. Q.; LaBombard, B.; Burke, W.

2017-07-01

A new servomotor drive system has been developed for the horizontal reciprocating probe on the Alcator C-Mod tokamak. Real-time measurements of plasma temperature and density—through use of a mirror Langmuir probe bias system—combined with a commercial linear servomotor and controller enable self-adaptive position control. Probe surface temperature and its rate of change are computed in real time and used to control probe insertion depth. It is found that a universal trigger threshold can be defined in terms of these two parameters; if the probe is triggered to retract when crossing the trigger threshold, it will reach the same ultimate surface temperature, independent of velocity, acceleration, or scrape-off layer heat flux scale length. In addition to controlling the probe motion, the controller is used to monitor and control all aspects of the integrated probe drive system.

Symmetric digit sets for elliptic curve scalar multiplication without precomputation

PubMed Central

Heuberger, Clemens; Mazzoli, Michela

2014-01-01

We describe a method to perform scalar multiplication on two classes of ordinary elliptic curves, namely E:y2=x3+Ax in prime characteristic p≡1mod4, and E:y2=x3+B in prime characteristic p≡1mod3. On these curves, the 4-th and 6-th roots of unity act as (computationally efficient) endomorphisms. In order to optimise the scalar multiplication, we consider a width-w-NAF (Non-Adjacent Form) digit expansion of positive integers to the complex base of τ, where τ is a zero of the characteristic polynomial x2−tx+p of the Frobenius endomorphism associated to the curve. We provide a precomputationless algorithm by means of a convenient factorisation of the unit group of residue classes modulo τ in the endomorphism ring, whereby we construct a digit set consisting of powers of subgroup generators, which are chosen as efficient endomorphisms of the curve. PMID:25190900

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

NASA Technical Reports Server (NTRS)

Spera, D. A.

1976-01-01

Preliminary estimates are presented of vibratory loads and stresses in hingeless and teetering rotors for the proposed NSF-NASA Mod-0 wind power system. Preliminary blade design utilizes a tapered tubular aluminum spar which supports nonstructural aluminum ribs and skin and is joined to the rotor hub by a steel shank tube. Stresses in the shank of the blade are calculated for static, rated, and overload operating conditions. Blade vibrations were limited to the fundamental flapping modes, which were elastic cantilever bending for hingeless rotor blades and rigid-body rotation for teetering rotor blades. The MOSTAB-C computer code was used to calculate aerodynamic and mechanical loads. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. The hingeless rotor analyzed does not appear to be structurally stable during overloads.

ModSAF Software Architecture Design and Overview Document

DTIC Science & Technology

1993-12-20

ADVANCED DISTRIBUTED SIMULATIONTECHNOLOGY AD-A282 740 ModSAF SOFTWARE ARCHITECTURE DESIGN AND OVERVIEW DOCUMENT Ver 1.0 - 20 December 1993 D T...AND SUBTITLE 5. FUNDING NUMBERS MOdSAF SOFTWARE ARCHITECTURE DESIGN AND OVERVIEW DOCUMENT C N61339-91-D-O00, Delivery Order (0021), ModSAF (CDRL A004) 6

Improvement of satellite-based gross primary production through incorporation of high resolution input data over east asia

NASA Astrophysics Data System (ADS)

Park, Haemi; Im, Jungho; Kim, Miae

2016-04-01

Photosynthesis of plants is the main mechanism of carbon absorption from the atmosphere into the terrestrial ecosystem and it contributes to remove greenhouse gases such as carbon dioxide. Annually, 120 Gt of C is supposed to be assimilated through photosynthetic activity of plants as the gross primary production (GPP) over global land area. In terms of climate change, GPP modelling is essential to understand carbon cycle and the balance of carbon budget over various ecosystems. One of the GPP modelling approaches uses light use efficiency that each vegetation type has a specific efficiency for consuming solar radiation related with temperature and humidity. Satellite data can be used to measure various meteorological and biophysical factors over vast areas, which can be used to quantify GPP. NASA Earth Observing System (EOS) program provides Moderate Resolution Imaging Spectroradiometer (MODIS)-derived global GPP product, namely MOD17A2H, on a daily basis. However, significant underestimation of MOD17A2H has been reported in Eastern Asia due to its dense forest distribution and humid condition during monsoon rainy season in summer. The objective of this study was to improve underestimation of MODIS GPP (MOD17A2H) by incorporating meteorological data-temperature, relative humidity, and solar radiation-of higher spatial resolution than data used in MOD17A2H. Landsat-based land cover maps of finer resolution observation and monitoring - global land cover (FROM-GLC) at 30m resolution were used for selection of light use efficiency (LUE). GPP (eq1. GPP = APAR×LUE) is computed by multiplication of APAR (IPAR×fPAR) and LUE (ɛ= ɛmax×T(°C)scalar×VPD(Pa)scalar, where, T is temperature, VPD is vapour pressure deficit) in this study. Meteorological data of Japanese 55-year Reanalysis (JRA-55, 0.56° grid, 3hr) were used for calculation of GPP in East Asia, including Eastern part of China, Korean peninsula, and Japan. Results were validated using flux tower-observed GPP data of AsiaFlux. Results showed that about 40% of underestimation of monthly average of MOD17A2H is confirmed and underestimation of MOD17A2 was improved from 42.3% and 60.4% to 8.3% and -26.2% for two flux tower sites (API site in Japan and GCK site in Korea), respectively. These improvements suggest that correction of LUE by finer land cover classification and/or better frequency of solar radiation data is effective where MOD17A2H does not work well. Further research will include evaluation of the proposed approach over areas in different climate conditions and environments.

Construction of a Mod-0A Wind Turbine in Clayton, New Mexico

NASA Image and Video Library

1977-11-21

TA Mod-0A 200-kilowatt wind turbine designed by National Aeronautics and Space Administration (NASA) Lewis Research Center and constructed in Clayton, New Mexico. The wind turbine program was a joint effort by NASA and the Energy Research and Development Administration (ERDA) during the 1970s to develop less expensive forms of energy. NASA Lewis was assigned the responsibility of developing large horizontal-axis wind turbines. The program included a series of increasingly powerful wind turbines, designated: Mod-0A, Mod-1, WTS-4, and Mod-5. The program’s first device was a Mod-0 100-kilowatt wind turbine test bed built at NASA’s Plum Brook Station. This Mod-0A 200-kilowatt turbine built in Clayton in 1977 was the program’s second device. It included a 125-foot long blade atop a 100-foot tall tower. The Mod-0A was designed to determine the turbine’s operating problems, integrate the system with the local utilities, and assess the attitude of the local community. There were additional Mod-0A turbines built in Culebra, Puerto Rico; Block Island, Rhode Island; and Oahu, Hawaii. The Mod-0A turbines were initially unreliable and suffered issues with the durability of the rotor blade. Lewis engineers addressed the problems, and the wind turbines proved to be reliable and efficient devices that operated for a number of years. The information gained from these early models was vital to the design and improvement of the later generations.

Effects of different titanium zirconium implant surfaces on initial supragingival plaque formation.

PubMed

John, Gordon; Becker, Jürgen; Schwarz, Frank

2017-07-01

The aim of the current study was the evaluation of biofilm development on different implant surfaces. Initial biofilm formation was investigated on five different implant surfaces, machined titanium (MTi), modified machined acid-etched titanium (modMATi), machined titanium zirconium (MTiZr), modified machined and acid-etched titanium zirconium (modMATiZr) and sandblasted large grid and acid-etched titanium zirconium surface (SLATiZr) for 24 and 48 h. Biocompatibility was tested after tooth brushing of the samples via cell viability testing with human gingival fibroblasts. After 24 h of biofilm collection, mean plaque surface was detected in the following descending order: After 24 h: MTiZr > MTi > SLATiZr > modMATiZr > modMATi. Both M surfaces showed significant higher biofilm formation than the other groups. After 48 h: MTiZr > MTi > SLATiZr > modMATiZr > modMATi. After tooth brushing: SLATiZr > modMATi > modMATiZr > MTi > MTiZr. All native samples depicted significant higher cell viability than their corresponding surfaces after biofilm removal procedure. The TiZr groups especially the modMATiZr group showed slower and less biofilm formation. In combination with the good biocompatibility, both modMA surfaces seem to be interesting candidates for surfaces in transgingival implant design. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Turbofan noise generation. Volume 2: Computer programs

NASA Technical Reports Server (NTRS)

Ventres, C. S.; Theobald, M. A.; Mark, W. D.

1982-01-01

The use of a package of computer programs developed to calculate the in duct acoustic mods excited by a fan/stator stage operating at subsonic tip speed is described. The following three noise source mechanisms are included: (1) sound generated by the rotor blades interacting with turbulence ingested into, or generated within, the inlet duct; (2) sound generated by the stator vanes interacting with the turbulent wakes of the rotor blades; and (3) sound generated by the stator vanes interacting with the velocity deficits in the mean wakes of the rotor blades. The computations for three different noise mechanisms are coded as three separate computer program packages. The computer codes are described by means of block diagrams, tables of data and variables, and example program executions; FORTRAN listings are included.

Turbofan noise generation. Volume 2: Computer programs

NASA Astrophysics Data System (ADS)

Ventres, C. S.; Theobald, M. A.; Mark, W. D.

1982-07-01

The use of a package of computer programs developed to calculate the in duct acoustic mods excited by a fan/stator stage operating at subsonic tip speed is described. The following three noise source mechanisms are included: (1) sound generated by the rotor blades interacting with turbulence ingested into, or generated within, the inlet duct; (2) sound generated by the stator vanes interacting with the turbulent wakes of the rotor blades; and (3) sound generated by the stator vanes interacting with the velocity deficits in the mean wakes of the rotor blades. The computations for three different noise mechanisms are coded as three separate computer program packages. The computer codes are described by means of block diagrams, tables of data and variables, and example program executions; FORTRAN listings are included.

Clinical application of a novel diagnostic scheme including pancreatic β‑cell dysfunction for traumatic multiple organ dysfunction syndrome.

PubMed

Wang, Zhan-Ke; Chen, Rong-Jian; Wang, Shi-Liang; Li, Guang-Wei; Zhu, Zhong-Zhen; Huang, Qiang; Chen, Zi-Li; Chen, Fan-Chang; Deng, Lei; Lan, Xiao-Peng; Hu, Tian

2018-01-01

A novel diagnostic scheme that includes pancreatic β‑cell dysfunction analysis for the diagnosis of traumatic multiple organ dysfunction syndrome (MODS) was investigated to assist in the early diagnosis and detection of MODS. Early intervention and treatment of MODS has been associated with a reduced mortality rate. A total of 2,876 trauma patients (including patients post‑major surgery) were admitted to the intensive care unit of the authors' hospital between December 2010 and December 2015 and enrolled in the present study. There were 205 cases where the patient succumbed to their injuries. In addition to the conventional diagnostic scheme for traumatic MODS, indexes of pancreatic β‑cell dysfunction [fasting blood‑glucose (FBG), homeostatic model assessment‑β and (blood insulin concentration 30 min following glucose loading‑fasting insulin concentration)/(blood glucose concentration 30 min following glucose loading‑FBG concentration)] were included to establish an improved diagnostic scheme for traumatic MODS. The novel scheme was subsequently used in clinical practice alongside the conventional scheme and its effect was evaluated. The novel scheme had a significantly higher positive number of MODS diagnoses for all trauma patients compared with the conventional scheme (12.48 vs. 8.87%; P<0.01). No significant difference was identified in the final percentage of positive of MODS diagnoses for trauma‑associated mortality patients between the novel (88.30%) and the conventional scheme (86.34%). The novel scheme had a significantly higher positive number of MODS diagnoses for trauma‑associated mortality patients 3 days prior to patients succumbing to MODS compared with the conventional scheme (80.98 vs. 64.39%; P<0.01). The consensus of the MODS diagnosis of all trauma patients between the novel scheme and the conventional scheme was 100%; however, out of the patients diagnosed as positive by novel scheme 71.03% were positive by the conventional scheme. The consensus between the final MODS diagnosis and the MODS diagnosis 3 days prior to patients succumbing to their injuries between the novel scheme and the conventional scheme was 100%; however, out of the patients diagnosed as positive by novel scheme 97.79 were positive by the conventional scheme of the 205 patients who succumbed to MODS and out of the patients diagnosed as positive for MODS by novel scheme 3 days prior to succumbing, 79.52% were positive by the conventional scheme. The results of the present study demonstrated that the novel diagnostic scheme using the relevant indexes of pancreatic β‑cell dysfunction for diagnosis of traumatic MODS, was able to diagnose MODS early without excessively extending the diagnostic scope. Its clinical application should be promoted.

An overview of instrumentation for the Large Binocular Telescope

NASA Astrophysics Data System (ADS)

Wagner, R. Mark

2012-09-01

An overview of instrumentation for the Large Binocular Telescope (LBT) is presented. Optical instrumentation includes the Large Binocular Camera (LBC), a pair of wide-field (27' x 27') mosaic CCD imagers at the prime focus, and the Multi-Object Double Spectrograph (MODS), a pair of dual-beam blue-red optimized long-slit spectrographs mounted at the left and right direct F/15 Gregorian foci incorporating multiple slit masks for multi-object spectroscopy over a 6' field and spectral resolutions of up to 2000. Infrared instrumentation includes the LBT Near-IR Spectroscopic Utility with Camera and Integral Field Unit for Extragalactic Research (LUCI), a modular near-infrared (0.9-2.5 μm) imager and spectrograph pair mounted at the left and right front bent F/15 Gregorian foci and designed for seeing-limited (FOV: 4' × 4') imaging, long-slit spectroscopy, and multiobject spectroscopy utilizing cooled slit masks and diffraction limited (FOV: 0'.5 × 0'.5) imaging and long-slit spectroscopy. Strategic instruments under development that can utilize the full 23-m baseline of the LBT include an interferometric cryogenic beam combiner with near-infrared and thermal-infrared instruments for Fizeau imaging and nulling interferometry (LBTI) and an optical bench near-infrared beam combiner utilizing multi-conjugate adaptive optics for high angular resolution and sensitivity (LINC-NIRVANA). LBTI is currently undergoing commissioning on the LBT and utilizing the installed adaptive secondary mirrors in both single- sided and two-sided beam combination modes. In addition, a fiber-fed bench spectrograph (PEPSI) capable of ultra high resolution spectroscopy and spectropolarimetry (R = 40,000-300,000) will be available as a principal investigator instrument. Over the past four years the LBC pair, LUCI1, and MODS1 have been commissioned and are now scheduled for routine partner science observations. The delivery of both LUCI2 and MODS2 is anticipated before the end of 2012. The availability of all these instruments mounted simultaneously on the LBT permits unique science, flexible scheduling, and improved operational support.

FORCE2: A state-of-the-art two-phase code for hydrodynamic calculations

NASA Astrophysics Data System (ADS)

Ding, Jianmin; Lyczkowski, R. W.; Burge, S. W.

1993-02-01

A three-dimensional computer code for two-phase flow named FORCE2 has been developed by Babcock and Wilcox (B & W) in close collaboration with Argonne National Laboratory (ANL). FORCE2 is capable of both transient as well as steady-state simulations. This Cartesian coordinates computer program is a finite control volume, industrial grade and quality embodiment of the pilot-scale FLUFIX/MOD2 code and contains features such as three-dimensional blockages, volume and surface porosities to account for various obstructions in the flow field, and distributed resistance modeling to account for pressure drops caused by baffles, distributor plates and large tube banks. Recently computed results demonstrated the significance of and necessity for three-dimensional models of hydrodynamics and erosion. This paper describes the process whereby ANL's pilot-scale FLUFIX/MOD2 models and numerics were implemented into FORCE2. A description of the quality control to assess the accuracy of the new code and the validation using some of the measured data from Illinois Institute of Technology (UT) and the University of Illinois at Urbana-Champaign (UIUC) are given. It is envisioned that one day, FORCE2 with additional modules such as radiation heat transfer, combustion kinetics and multi-solids together with user-friendly pre- and post-processor software and tailored for massively parallel multiprocessor shared memory computational platforms will be used by industry and researchers to assist in reducing and/or eliminating the environmental and economic barriers which limit full consideration of coal, shale and biomass as energy sources, to retain energy security, and to remediate waste and ecological problems.

Automotive Stirling Engine Mod 1 Design Review, Volume 1

NASA Technical Reports Server (NTRS)

1982-01-01

Risk assessment, safety analysis of the automotive stirling engine (ASE) mod I, design criteria and materials properties for the ASE mod I and reference engines, combustion are flower development, and the mod I engine starter motor are discussed. The stirling engine system, external heat system, hot engine system, cold engine system, and engine drive system are also discussed.

B61 Mod 12 Life Extension Program Tailkit Assembly (B61 Mod 12 LEP TKA)

DTIC Science & Technology

2015-12-01

Selected Acquisition Report ( SAR ) RCS: DD-A&T(Q&A)823-468 B61 Mod 12 Life Extension Program Tailkit Assembly (B61 Mod 12 LEP TKA) As of FY 2017... SAR March 23, 2016 10:38:20 UNCLASSIFIED 2 Table of Contents Common Acronyms and Abbreviations for MDAP Programs 3 Program Information...Unit Cost B61 Mod 12 LEP TKA December 2015 SAR March 23, 2016 10:38:20 UNCLASSIFIED 3 PB - President’s Budget PE - Program Element PEO - Program

Department of the Navy Justification of Estimates for Fiscal Year 1984 Submitted to Congress January 1983. Operation & Maintenance, Navy. Book 2. Budget Activity 7: Central Supply & Maintenance.

DTIC Science & Technology

1983-01-01

Sidewinder TD Mods 2/1,291 3/1,762 4/5,540 Cost $130 $252 $573 Snarrow TD Mods 5/2,045 2/186 6/564 Cost $556 $110 $419 Shrike TD Mods -/- 4/2,930 3/2,307 Cost...574 $713 Standard Arm TO/Mods 1/87 ?/351 ?/296 Cost $72 $180 $158 Phoenix TD /Mods 4/889 4/554 3/642 Cost $219 $120 $?67 7 29 Activity Group: Air...Launched Weapons Rework (cont’d) III. Performance Criteria and Evaluation FY 1982 FY 1983 FY 1984 (cont’d) Harpoon TD /Mods 6/396 16/2,512 14/1,195

Current status of the facility instrumentation suite at the Large Binocular Telescope Observatory

NASA Astrophysics Data System (ADS)

Rothberg, Barry; Kuhn, Olga; Edwards, Michelle L.; Hill, John M.; Thompson, David; Veillet, Christian; Wagner, R. Mark

2016-07-01

The current status of the facility instrumentation for the Large Binocular Telescope (LBT) is reviewed. The LBT encompasses two 8.4 meter primary mirrors on a single mount yielding an effective collecting area of 11.8 meters or 23 meters when interferometrically combined. The three facility instruments at LBT include: 1) the Large Binocular Cameras (LBCs), each with a 23'× 25' field of view (FOV). The blue optimized and red optimized optical wavelength LBCs are mounted at the prime focus of the SX (left) and DX (right) primary mirrors, respectively. Combined, the filter suite of the two LBCs cover 0.3-1.1 μm, including the addition of new medium-band filters centered on TiO (0.78 μm) and CN (0.82 μm) 2) the Multi-Object Double Spectrograph (MODS), two identical optical spectrographs each mounted at the straight through f/15 Gregorian focus of the primary mirrors. The capabilities of MODS-1 and -2 include imaging with Sloan filters (u, g, r, i, and z) and medium resolution (R ˜ 2000) spectroscopy, each with 24 interchangeable masks (multi-object or longslit) over a 6'× 6' FOV. Each MODS is capable of blue (0.32-0.6 μm) and red (0.5-1.05 μm) wavelength only spectroscopy coverage or both can employ a dichroic for 0.32-1.05 μm wavelength coverage (with reduced coverage from 0.56- 0.57 μm) and 3) the two LBT Utility Camera in the Infrared instruments (LUCIs), are each mounted at a bent-front Gregorian f/15 focus of a primary mirror. LUCI-1 and 2 are designed for seeing-limited (4'× 4' FOV) and active optics using thin-shell adaptive secondary mirrors (0.5'× 0.5' FOV) imaging and spectroscopy over the wavelength range of 0.95-2.5 μm and spectroscopic resolutions of 400 <= R <= 11000 (depending on the combination of grating, slits, and cameras used). The spectroscopic capabilities also include 32 interchangeable multi-object or longslit masks which are cryogenically cooled. Currently all facility instruments are in-place at the LBT and, for the first time, have been on-sky for science observations. In Summer 2015 LUCI-1 was refurbished to replace the infrared detector; to install a high-resolution camera to take advantage of the active optics SX secondary; and to install a grating designed primarily for use with high resolution active optics. Thus, like MODS-1 and -2, both LUCIs now have specifications nearly identical to each other. The software interface for both LUCIs have also been replaced, allowing both instruments to be run together from a single interface. With the installation of all facility instruments finally complete we also report on the first science use of "mixed-mode" operations, defined as the combination of different paired instruments with each mirror (i.e. LBC+MODS, LBC+LUCI, LUCI+MODS). Although both primary mirrors reside on a single fixed mount, they are capable of operating as independent entities within a defined "co-pointing" limit. This provides users with the additional capability to independently dither each mirror or center observations on two different sets of spatial coordinates within this limit.

A snow cover climatology for the Pyrenees from MODIS snow products

NASA Astrophysics Data System (ADS)

Gascoin, S.; Hagolle, O.; Huc, M.; Jarlan, L.; Dejoux, J.-F.; Szczypta, C.; Marti, R.; Sánchez, R.

2014-11-01

The seasonal snow in the Pyrenees is critical for hydropower production, crop irrigation and tourism in France, Spain and Andorra. Complementary to in situ observations, satellite remote sensing is useful to monitor the effect of climate on the snow dynamics. The MODIS daily snow products (Terra/MOD10A1 and Aqua/MYD10A1) are widely used to generate snow cover climatologies, yet it is preferable to assess their accuracies prior to their use. Here, we use both in situ snow observations and remote sensing data to evaluate the MODIS snow products in the Pyrenees. First, we compare the MODIS products to in situ snow depth (SD) and snow water equivalent (SWE) measurements. We estimate the values of the SWE and SD best detection thresholds to 40 mm water equivalent (we) and 105 mm respectively, for both MOD10A1 and MYD10A1. Kappa coefficients are within 0.74 and 0.92 depending on the product and the variable. Then, a set of Landsat images is used to validate MOD10A1 and MYD10A1 for 157 dates between 2002 and 2010. The resulting accuracies are 97% (κ = 0.85) for MOD10A1 and 96% (κ = 0.81) for MYD10A1, which indicates a good agreement between both datasets. The effect of vegetation on the results is analyzed by filtering the forested areas using a land cover map. As expected, the accuracies decreases over the forests but the agreement remains acceptable (MOD10A1: 96%, κ = 0.77; MYD10A1: 95%, κ = 0.67). We conclude that MODIS snow products have a sufficient accuracy for hydroclimate studies at the scale of the Pyrenees range. Using a gapfilling algorithm we generate a consistent snow cover climatology, which allows us to compute the mean monthly snow cover duration per elevation band. We finally analyze the snow patterns for the atypical winter 2011-2012. Snow cover duration anomalies reveal a deficient snowpack on the Spanish side of the Pyrenees, which seems to have caused a drop in the national hydropower production.

Documenting Models for Interoperability and Reusability ...

EPA Pesticide Factsheets

Many modeling frameworks compartmentalize science via individual models that link sets of small components to create larger modeling workflows. Developing integrated watershed models increasingly requires coupling multidisciplinary, independent models, as well as collaboration between scientific communities, since component-based modeling can integrate models from different disciplines. Integrated Environmental Modeling (IEM) systems focus on transferring information between components by capturing a conceptual site model; establishing local metadata standards for input/output of models and databases; managing data flow between models and throughout the system; facilitating quality control of data exchanges (e.g., checking units, unit conversions, transfers between software languages); warning and error handling; and coordinating sensitivity/uncertainty analyses. Although many computational software systems facilitate communication between, and execution of, components, there are no common approaches, protocols, or standards for turn-key linkages between software systems and models, especially if modifying components is not the intent. Using a standard ontology, this paper reviews how models can be described for discovery, understanding, evaluation, access, and implementation to facilitate interoperability and reusability. In the proceedings of the International Environmental Modelling and Software Society (iEMSs), 8th International Congress on Environmental Mod

Mod-0A Wind Turbine in Block Island, Rhode Island

NASA Image and Video Library

1979-06-21

A Mod-0A 200-kilowatt wind turbine designed by National Aeronautics and Space Administration (NASA) Lewis Research Center and constructed in Block Island, Rhode Island. The wind turbine program was a joint program between NASA and the Energy Research and Development Administration (ERDA) during the 1970s to develop less expensive forms of energy. NASA Lewis was assigned the responsibility of developing large horizontal-axis wind turbines. The program included a series of increasingly powerful wind turbines, designated: Mod-0A, Mod-1, WTS-4, and Mod-5. The program’s first device was a Mod-0 100-kilowatt wind turbine test bed at NASA’s Plum Brook Station. This Mod-0A 200-kilowatt turbine, completed in 1977, was the program’s second-generation device. It included a 125-foot diameter blade atop a 100-foot tall tower. This early wind turbine was designed determine its operating problems, integrate with the local utilities, and assess the attitude of the local community. There were additional Mod-0A turbines built in Culebra, Puerto Rico; Clayton, New Mexico; and Oahu, Hawaii. The Mod-0A turbines suffered durability issues with the rotor blade and initially appeared unreliable. NASA engineers addressed the problems, and the turbines proved to be reliable and efficient devices that operated for a number of years. The information gained from these early models was vital to the design and improvement of the later generations.

Proof without Words: Squares Modulo 3

ERIC Educational Resources Information Center

Nelsen, Roger B.

2013-01-01

Using the fact that the sum of the first n odd numbers is n[superscript 2], we show visually that n[superscript 2] is the same as 0 (mod 3) when n is the same as 0 (mod 3), and n[superscript 2] is the same as 1 (mod 3) when n is the same as plus or minus 1 (mod 3).

MOD-5A wind turbine generator program design report: Volume 1: Executive Summary

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator covering work performed between July 1980 and June 1984 is discussed. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 1, the Executive Summary, summarizes all phases of the MOD-5A program. The performance and cost of energy generated by the MOD-5A are presented. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation, power generation, and control and instrumentation subsystems - is described briefly. The early phases of the MOD-5A program, during which the design was analyzed and optimized, and new technologies and materials were developed, are discussed. Manufacturing, quality assurance, and safety plans are presented. The volume concludes with an index of volumes 2 and 3.

Hurricane IKE Recovery Efforts - MOD Volunteers

NASA Image and Video Library

2008-09-18

Hurricane IKE Recovery Efforts - MOD Volunteers Location: Clear LAke Area Subject: MOD Volunteers assist fellow employees at their homes during the recovery from hurricane IKE. Photographer: Tom Murray (USA Photographer)

Atmospheric Sensitivity to Spectral Top-of-Atmosphere Solar Irradiance Perturbations, Using MODTRAN-5 Radiative Transfer Algorithm

NASA Astrophysics Data System (ADS)

Anderson, G.; Berk, A.; Harder, G.; Fontenla, J.; Shettle, E.; Pilewski, P.; Kindel, B.; Chetwynd, J.; Gardner, J.; Hoke, M.; Jordan, A.; Lockwood, R.; Felde, G.; Archarya, P.

2006-12-01

The opportunity to insert state-of-the-art solar irradiance measurements and calculations, with subtle perturbations, into a narrow spectral resolution radiative transfer model has recently been facilitated through release of MODTRAN-5 (MOD5). The new solar data are from: (1) SORCE satellite measurements of solar variability over solar rotation cycle, & (2) ultra-narrow calculation of a new solar source irradiance, extending over the full MOD5 spectral range, from 0.2 um to far-IR. MODTRAN-5, MODerate resolution radiance and TRANsmittance code, has been developed collaboratively by Air Force Research Laboratory and Spectral Sciences, Inc., with history dating back to LOWTRAN. It includes approximations for all local thermodynamic equilibrium terms associated with molecular, cloud, aerosol and surface components for emission, scattering, and reflectance, including multiple scattering, refraction and a statistical implementation of Correlated-k averaging. The band model is based on 0.1 cm-1 (also 1.0, 5.0 and 15.0 cm-1 statistical binning for line centers within the interval, captured through an exact formulation of the full Voigt line shape. Spectroscopic parameters are from HITRAN 2004 with user-defined options for additional gases. Recent validation studies show MOD5 replicates line-by-line brightness temperatures to within ~0.02ºK average and <1.0ºK RMS. MOD5 can then serve as a surrogate for a variety of perturbation studies, including the two modes for the solar source function, Io. (1) Data from the Solar Radiation and Climate Experiment (SORCE) satellite mission provide state-of-the-art measurements of UV, visible, near-IR, plus total solar radiation, on near real-time basis. These internally consistent estimates of Sun's output over solar rotation and longer time scales are valuable inputs for studying effects of Sun's radiation on Earth's atmosphere and climate. When solar rotation encounters bright plage and dark sunspots, relative variations are expected to be very small in visible wavelengths, although absolute power is substantial. SORCE's Spectral Irradiance Monitor measurements are readily included in comparative MOD5 calculations. (2) The embedded solar irradiance within MOD5 must be compatible with the chosen band model resolution binning. By matching resolutions some issues related to the correlated-k band model parameterizations can be tested. Two high resolution solar irradiances, the MOD5 default irradiance (Kurucz) and a new compilation associated with Solar Radiation Physical Modeling project (Fontenla), are compared to address the potential impact of discrepancies between any sets of irradiances. The magnitude of solar variability, as measured and calculated, can lead to subtle changes in heating/cooling rates throughout the atmosphere, as a function of altitude and wavelength. By holding chemical & dynamical responses constant, only controlled distributions of absorbing gases, aerosols and clouds will contribute to observed 1st order radiative effects.

Experience and Assessment of the DOE/NASA Mod-1 2000 Kw Wind Turbine Generator at Boone, North Carolina

NASA Technical Reports Server (NTRS)

Collins, J. L.; Shaltens, R. K.; Poor, R. H.; Barton, R. S.

1982-01-01

The Mod 1 program objectives are defined. The Mod 1 wind turbine is described. In addition to the steel blade operated on the wind turbine, a composite blade was designed and manufactured. During the early phase of the manufacturing cycle of Mod 1A configuration was designed that identified concepts such as partial span control, a soft tower, and upwind teetered rotors that were incorporated in second and third generation industry designs. The Mod 1 electrical system performed as designed, with voltage flicker characteristics within acceptable utility limits.

Cause for Concern or Moral Panic? The Prospects of the Swedish Mods in Retrospect

ERIC Educational Resources Information Center

Alm, Susanne; Nilsson, Anders

2011-01-01

The Swedish mods of the 1960s frightened the parental generation like few other youth cultures. Was the concern justified--was the mod culture a hotbed of social maladjustment? Or would the mods come to live conventional lives to the same extent as their peers? We present analyses from a large longitudinal study allowing for a follow-up of…

Mod-2 wind turbine system development. Volume 2: Detailed report

NASA Technical Reports Server (NTRS)

1982-01-01

Progress in the design, fabrication, and testing of a wind turbine system is reported. The development of the MOD-2 wind turbine through acceptance testing and initial operational evaluation is documented. The MOD-2 project intends to develop early commercialization of wind energy. The first wind turbine farm (three MOD-2 units) are now being operated at the Bonneville Power Administration site near Goldendale, Washington.

Cost-effectiveness analysis of microscopic observation drug susceptibility test versus Xpert MTB/Rif test for diagnosis of pulmonary tuberculosis in HIV patients in Uganda.

PubMed

Walusimbi, Simon; Kwesiga, Brendan; Rodrigues, Rashmi; Haile, Melles; de Costa, Ayesha; Bogg, Lennart; Katamba, Achilles

2016-10-10

Microscopic Observation Drug Susceptibility (MODS) and Xpert MTB/Rif (Xpert) are highly sensitive tests for diagnosis of pulmonary tuberculosis (PTB). This study evaluated the cost effectiveness of utilizing MODS versus Xpert for diagnosis of active pulmonary TB in HIV infected patients in Uganda. A decision analysis model comparing MODS versus Xpert for TB diagnosis was used. Costs were estimated by measuring and valuing relevant resources required to perform the MODS and Xpert tests. Diagnostic accuracy data of the tests were obtained from systematic reviews involving HIV infected patients. We calculated base values for unit costs and varied several assumptions to obtain the range estimates. Cost effectiveness was expressed as costs per TB patient diagnosed for each of the two diagnostic strategies. Base case analysis was performed using the base estimates for unit cost and diagnostic accuracy of the tests. Sensitivity analysis was performed using a range of value estimates for resources, prevalence, number of tests and diagnostic accuracy. The unit cost of MODS was US$ 6.53 versus US$ 12.41 of Xpert. Consumables accounted for 59 % (US$ 3.84 of 6.53) of the unit cost for MODS and 84 % (US$10.37 of 12.41) of the unit cost for Xpert. The cost effectiveness ratio of the algorithm using MODS was US$ 34 per TB patient diagnosed compared to US$ 71 of the algorithm using Xpert. The algorithm using MODS was more cost-effective compared to the algorithm using Xpert for a wide range of different values of accuracy, cost and TB prevalence. The cost (threshold value), where the algorithm using Xpert was optimal over the algorithm using MODS was US$ 5.92. MODS versus Xpert was more cost-effective for the diagnosis of PTB among HIV patients in our setting. Efforts to scale-up MODS therefore need to be explored. However, since other non-economic factors may still favour the use of Xpert, the current cost of the Xpert cartridge still needs to be reduced further by more than half, in order to make it economically competitive with MODS.

Risk Factors for Multiple Organ Dysfunction Syndrome in Severe Stroke Patients

PubMed Central

Yang, Shuna; Li, Yue; Yuan, Junliang; Yang, Lei; Li, Shujuan; Hu, Wenli

2016-01-01

Background Severe stroke patients have poor clinical outcome which may be associated with development of multiple organ dysfunction syndrome (MODS). Therefore, the aim of our study was to investigate independent risk factors for development of MODS in severe stroke patients. Methods Ninety seven severe stroke patients were prospective recruited from Jan 2011 to Jun 2015. The development of MODS was identified by Sequential Organ Failure Assessment (SOFA) score (score ≥ 3, at least two organs), which was assessed on day 1, 4, 7, 10 and 14 after admission. Baseline characteristics, Acute Physiology and Chronic Health Evaluation (APACHE) II score, Glasgow coma score (GCS) and cerebral imaging parameters were collected at admission. Cox regression was performed to determine predictors for the development of MODS. Medical complications after admission and in-hospital mortality were also investigated. Results 33 (34%) patients were in MODS group and 64 (66%) were in non-MODS group within 14 days after admission. Patients in MODS group had more smoker (51.5% vs 28.1%, p = 0.023), higher NIHSS score (23.48 ± 6.12 vs 19.81 ± 4.83, p = 0.004), higher APACHE II score (18.70 ± 5.18 vs 15.64 ± 4.36, p = 0.003) and lower GCS score (6.33 ± 2.48 vs 8.14 ± 2.73, p = 0.002). They also had higher rate of infarction in multi vascular territories (36.4% vs 10.9%, p = 0.003). The most common complication in all patients was pulmonary infection, while complication scores were comparable between two groups. Patients with MODS had higher in-hospital mortality (69.7% vs 9.4%, p = 0.000). In Cox regression, NIHSS score (RR = 1.084, 95% CI 1.019–1.153) and infarction in multi vascular territories (RR = 2.345 95% CI 1.105–4.978) were independent risk factors for development of MODS. Conclusions In acute phase of stroke, NIHSS score and infarction in multi vascular territories predicted MODS in severe stroke patients. Moreover, patients with MODS had higher in-hospital mortality, suggesting that early identification of MODS is critical important. PMID:27893797

Evaluating the Auto-MODS Assay, a Novel Tool for Tuberculosis Diagnosis for Use in Resource-Limited Settings

PubMed Central

Wang, Linwei; Mohammad, Sohaib H.; Li, Qiaozhi; Rienthong, Somsak; Rienthong, Dhanida; Nedsuwan, Supalert; Mahasirimongkol, Surakameth; Yasui, Yutaka

2014-01-01

There is an urgent need for simple, rapid, and affordable diagnostic tests for tuberculosis (TB) to combat the great burden of the disease in developing countries. The microscopic observation drug susceptibility assay (MODS) is a promising tool to fill this need, but it is not widely used due to concerns regarding its biosafety and efficiency. This study evaluated the automated MODS (Auto-MODS), which operates on principles similar to those of MODS but with several key modifications, making it an appealing alternative to MODS in resource-limited settings. In the operational setting of Chiang Rai, Thailand, we compared the performance of Auto-MODS with the gold standard liquid culture method in Thailand, mycobacterial growth indicator tube (MGIT) 960 plus the SD Bioline TB Ag MPT64 test, in terms of accuracy and efficiency in differentiating TB and non-TB samples as well as distinguishing TB and multidrug-resistant (MDR) TB samples. Sputum samples from clinically diagnosed TB and non-TB subjects across 17 hospitals in Chiang Rai were consecutively collected from May 2011 to September 2012. A total of 360 samples were available for evaluation, of which 221 (61.4%) were positive and 139 (38.6%) were negative for mycobacterial cultures according to MGIT 960. Of the 221 true-positive samples, Auto-MODS identified 212 as positive and 9 as negative (sensitivity, 95.9%; 95% confidence interval [CI], 92.4% to 98.1%). Of the 139 true-negative samples, Auto-MODS identified 135 as negative and 4 as positive (specificity, 97.1%; 95% CI, 92.8% to 99.2%). The median time to culture positivity was 10 days, with an interquartile range of 8 to 13 days for Auto-MODS. Auto-MODS is an effective and cost-sensitive alternative diagnostic tool for TB diagnosis in resource-limited settings. PMID:25378569

MOD Tool (Microwave Optics Design Tool)

NASA Technical Reports Server (NTRS)

Katz, Daniel S.; Borgioli, Andrea; Cwik, Tom; Fu, Chuigang; Imbriale, William A.; Jamnejad, Vahraz; Springer, Paul L.

1999-01-01

The Jet Propulsion Laboratory (JPL) is currently designing and building a number of instruments that operate in the microwave and millimeter-wave bands. These include MIRO (Microwave Instrument for the Rosetta Orbiter), MLS (Microwave Limb Sounder), and IMAS (Integrated Multispectral Atmospheric Sounder). These instruments must be designed and built to meet key design criteria (e.g., beamwidth, gain, pointing) obtained from the scientific goals for the instrument. These criteria are frequently functions of the operating environment (both thermal and mechanical). To design and build instruments which meet these criteria, it is essential to be able to model the instrument in its environments. Currently, a number of modeling tools exist. Commonly used tools at JPL include: FEMAP (meshing), NASTRAN (structural modeling), TRASYS and SINDA (thermal modeling), MACOS/IMOS (optical modeling), and POPO (physical optics modeling). Each of these tools is used by an analyst, who models the instrument in one discipline. The analyst then provides the results of this modeling to another analyst, who continues the overall modeling in another discipline. There is a large reengineering task in place at JPL to automate and speed-up the structural and thermal modeling disciplines, which does not include MOD Tool. The focus of MOD Tool (and of this paper) is in the fields unique to microwave and millimeter-wave instrument design. These include initial design and analysis of the instrument without thermal or structural loads, the automation of the transfer of this design to a high-end CAD tool, and the analysis of the structurally deformed instrument (due to structural and/or thermal loads). MOD Tool is a distributed tool, with a database of design information residing on a server, physical optics analysis being performed on a variety of supercomputer platforms, and a graphical user interface (GUI) residing on the user's desktop computer. The MOD Tool client is being developed using Tcl/Tk, which allows the user to work on a choice of platforms (PC, Mac, or Unix) after downloading the Tcl/Tk binary, which is readily available on the web. The MOD Tool server is written using Expect, and it resides on a Sun workstation. Client/server communications are performed over a socket, where upon a connection from a client to the server, the server spawns a child which is be dedicated to communicating with that client. The server communicates with other machines, such as supercomputers using Expect with the username and password being provided by the user on the client.

Insulation of Enhancer-Promoter Communication by a Gypsy Transposon Insert in the Drosophila cut Gene: Cooperation between Suppressor of Hairy-wing and Modifier of mdg4 Proteins

PubMed Central

Gause, Maria; Morcillo, Patrick; Dorsett, Dale

2001-01-01

The Drosophila mod(mdg4) gene products counteract heterochromatin-mediated silencing of the white gene and help activate genes of the bithorax complex. They also regulate the insulator activity of the gypsy transposon when gypsy inserts between an enhancer and promoter. The Su(Hw) protein is required for gypsy-mediated insulation, and the Mod(mdg4)-67.2 protein binds to Su(Hw). The aim of this study was to determine whether Mod(mdg4)-67.2 is a coinsulator that helps Su(Hw) block enhancers or a facilitator of activation that is inhibited by Su(Hw). Here we provide evidence that Mod(mdg4)-67.2 acts as a coinsulator by showing that some loss-of-function mod(mdg4) mutations decrease enhancer blocking by a gypsy insert in the cut gene. We find that the C terminus of Mod(mdg4)-67.2 binds in vitro to a region of Su(Hw) that is required for insulation, while the N terminus mediates self-association. The N terminus of Mod(mdg4)-67.2 also interacts with the Chip protein, which facilitates activation of cut. Mod(mdg4)-67.2 truncated in the C terminus interferes in a dominant-negative fashion with insulation in cut but does not significantly affect heterochromatin-mediated silencing of white. We infer that multiple contacts between Su(Hw) and a Mod(mdg4)-67.2 multimer are required for insulation. We theorize that Mod(mdg4)-67.2 usually aids gene activation but can also act as a coinsulator by helping Su(Hw) trap facilitators of activation, such as the Chip protein. PMID:11416154

The Modified Frontal Behavioral Inventory (FBI-mod) for Patients with Frontotemporal Lobar Degeneration, Alzheimer's Disease, and Mild Cognitive Impairment.

PubMed

Suhonen, Noora-Maria; Hallikainen, Ilona; Hänninen, Tuomo; Jokelainen, Jari; Krüger, Johanna; Hall, Anette; Pikkarainen, Maria; Soininen, Hilkka; Remes, Anne M

2017-01-01

While behavioral symptoms are both early and prevalent features of behavioral variant frontotemporal dementia (bvFTD), they can be present in other types of dementia as well, including Alzheimer's disease (AD) and even mild cognitive impairment (MCI). The Frontal Behavioral Inventory (FBI) was specifically developed to capture the behavioral and personality changes in bvFTD; it has also been modified into a self-administered caregiver questionnaire (FBI-mod). We examined the utility of the FBI-mod in differentiating bvFTD (n = 26), primary progressive aphasia (PPA) (n = 7), AD (n = 53), and MCI (n = 50) patients, and investigated how the FBI-mod may be associated with neuropsychological measures. The bvFTD patients scored significantly higher as compared to all other patient groups on the FBI-mod Total (p < 0.005), Negative (p < 0.005), and Positive (p < 0.01) scores. The cut-off point for the FBI-mod Total score that best discriminated the bvFTD and AD patients in our sample was 16, thus substantially lower than reported for the original FBI. For the bvFTD group, only mild correlations emerged between the FBI-mod and the cognitive measures. However, significant correlations between the FBI-mod and depressive symptoms as measured by the BDI-II were found for bvFTD. This suggests that while behavioral symptoms appear independent from cognitive deficits in bvFTD, they may nevertheless be interrelated with depressive symptoms. We conclude that the FBI-mod is an easily administered behavioral scale that can aid in differential diagnosis of bvFTD and should be used in clinical practice. The FBI-mod may further be considered as an outcome measure in clinical trials.

Brahma regulates a specific trans-splicing event at the mod(mdg4) locus of Drosophila melanogaster

PubMed Central

Yu, Simei; Waldholm, Johan; Böhm, Stefanie; Visa, Neus

2014-01-01

The mod(mdg4) locus of Drosophila melanogaster contains several transcription units encoded on both DNA strands. The mod(mdg4) pre-mRNAs are alternatively spliced, and a very significant fraction of the mature mod(mdg4) mRNAs are formed by trans-splicing. We have studied the transcripts derived from one of the anti-sense regions within the mod(mdg4) locus in order to shed light on the expression of this complex locus. We have characterized the expression of anti-sense mod(mdg4) transcripts in S2 cells, mapped their transcription start sites and cleavage sites, identified and quantified alternatively spliced transcripts, and obtained insight into the regulation of the mod(mdg4) trans-splicing. In a previous study, we had shown that the alternative splicing of some mod(mdg4) transcripts was regulated by Brahma (BRM), the ATPase subunit of the SWI/SNF chromatin-remodeling complex. Here we show, using RNA interference and overexpression of recombinant BRM proteins, that the levels of BRM affect specifically the abundance of a trans-spliced mod(mdg4) mRNA isoform in both S2 cells and larvae. This specific effect on trans-splicing is accompanied by a local increase in the density of RNA polymerase II and by a change in the phosphorylation state of the C-terminal domain of the large subunit of RNA polymerase II. Interestingly, the regulation of the mod(mdg4) splicing by BRM is independent of the ATPase activity of BRM, which suggests that the mechanism by which BRM modulates trans-splicing is independent of its chromatin-remodeling activity. PMID:24526065

Second-line drug susceptibility breakpoints for Mycobacterium tuberculosis using the MODS assay.

PubMed

Trollip, A P; Moore, D; Coronel, J; Caviedes, L; Klages, S; Victor, T; Romancenco, E; Crudu, V; Ajbani, K; Vineet, V P; Rodrigues, C; Jackson, R L; Eisenach, K; Garfein, R S; Rodwell, T C; Desmond, E; Groessl, E J; Ganiats, T G; Catanzaro, A

2014-02-01

To establish breakpoint concentrations for the fluoroquinolones (moxifloxacin [MFX] and ofloxacin [OFX]) and injectable second-line drugs (amikacin [AMK], kanamycin [KM] and capreomycin [CPM]) using the microscopic observation drug susceptibility (MODS) assay. A multinational study conducted between February 2011 and August 2012 in Peru, India, Moldova and South Africa. In the first phase, breakpoints for the fluoroquinolones and injectable second-line drugs (n = 58) were determined. In the second phase, MODS second-line drug susceptibility testing (DST) as an indirect test was compared to MGIT™ DST (n = 89). In the third (n = 30) and fourth (n = 156) phases, we determined the reproducibility and concordance of MODS second-line DST directly from sputum. Breakpoints for MFX (0.5 μg/ml), OFX (1 μg/ml), AMK (2 μg/ml), KM (5 μg/ml) and CPM (2.5 μg/ml) were determined. In all phases, MODS results were highly concordant with MGIT DST. The few discrepancies suggest that the MODS breakpoint concentrations for some drugs may be too low. MODS second-line DST yielded comparable results to MGIT second-line DST, and is thus a promising alternative. Further studies are needed to confirm the accuracy of the drug breakpoints and the reliability of MODS second-line DST as a direct test.

Evaluating the role of land cover and climate uncertainties in computing gross primary production in Hawaiian Island ecosystems

Treesearch

Heather L. Kimball; Paul C. Selmants; Alvaro Moreno; Steve W. Running; Christian P. Giardina; Benjamin Poulter

2017-01-01

Gross primary production (GPP) is the Earth’s largest carbon flux into the terrestrial biosphere and plays a critical role in regulating atmospheric chemistry and global climate. The Moderate Resolution Imaging Spectrometer (MODIS)-MOD17 data product is a widely used remote sensing-based model that provides global estimates of spatiotemporal trends in GPP. When the...

Thermal-stress analysis for wood composite blade. [horizontal axis wind turbines

NASA Technical Reports Server (NTRS)

Fu, K. C.; Harb, A.

1984-01-01

The thermal-stress induced by solar insolation on a wood composite blade of a Mod-OA wind turbine was investigated. The temperature distribution throughout the blade (a heat conduction problem) was analyzed and the thermal-stress distribution of the blades caused by the temperature distribution (a thermal-stress analysis problem) was then determined. The computer programs used for both problems are included along with output examples.

Mentoring SFRM: A New Approach to International Space Station Flight Controller Training

NASA Technical Reports Server (NTRS)

Huning, Therese; Barshi, Immanuel; Schmidt, Lacey

2008-01-01

The Mission Operations Directorate (MOD) of the Johnson Space Center is responsible for providing continuous operations support for the International Space Station (ISS). Operations support requires flight controllers who are skilled in team performance as well as the technical operations of the ISS. Space Flight Resource Management (SFRM), a NASA adapted variant of Crew Resource Management (CRM), is the competency model used in the MOD. ISS flight controller certification has evolved to include a balanced focus on development of SFRM and technical expertise. The latest challenge the MOD faces is how to certify an ISS flight controller (operator) to a basic level of effectiveness in 1 year. SFRM training uses a two-pronged approach to expediting operator certification: 1) imbed SFRM skills training into all operator technical training and 2) use senior flight controllers as mentors. This paper focuses on how the MOD uses senior flight controllers as mentors to train SFRM skills. Methods: A mentor works with an operator throughout the training flow. Inserted into the training flow are guided-discussion sessions and on-the-job observation opportunities focusing on specific SFRM skills, including: situational leadership, conflict management, stress management, cross-cultural awareness, self care and team care while on-console, communication, workload management, and situation awareness. The mentor and operator discuss the science and art behind the skills, cultural effects on skills applications, recognition of good and bad skills applications, recognition of how skills application changes subtly in different situations, and individual goals and techniques for improving skills. Discussion: This mentoring program provides an additional means of transferring SFRM knowledge compared to traditional CRM training programs. Our future endeavors in training SFRM skills (as well as other organization s) may benefit from adding team performance skills mentoring. This paper explains our mentoring approach and discusses its effectiveness and future applicability in promoting SFRM/CRM skills.

Mobility on Demand Operational Concept Report.

DOT National Transportation Integrated Search

2017-09-10

This operational concept report provides an overview of the Mobility on Demand (MOD) concept and its evolution, description of the MOD ecosystem in a supply and demand framework, and its stakeholders and enablers. Leveraging the MOD ecosystem framewo...

MOD-2 wind turbine system concept and preliminary design report. Volume 2: Detailed report

NASA Technical Reports Server (NTRS)

1979-01-01

The configuration development of the MOD-2 wind turbine system (WTS) is documented. The MOD-2 WTS project is a continuation of DOE programs to develop and achieve early commercialization of wind energy. The MOD-2 is design optimized for commercial production rates which, in multiunit installations, will be integrated into a utility power grid and achieve a cost of electricity at less than four cents per kilowatt hour.

Promoting Physical Activity through Hand-Held Computer Technology

PubMed Central

King, Abby C.; Ahn, David K.; Oliveira, Brian M.; Atienza, Audie A.; Castro, Cynthia M.; Gardner, Christopher D.

2009-01-01

Background Efforts to achieve population-wide increases in walking and similar moderate-intensity physical activities potentially can be enhanced through relevant applications of state-of-the-art interactive communication technologies. Yet few systematic efforts to evaluate the efficacy of hand-held computers and similar devices for enhancing physical activity levels have occurred. The purpose of this first-generation study was to evaluate the efficacy of a hand-held computer (i.e., personal digital assistant [PDA]) for increasing moderate intensity or more vigorous (MOD+) physical activity levels over 8 weeks in mid-life and older adults relative to a standard information control arm. Design Randomized, controlled 8-week experiment. Data were collected in 2005 and analyzed in 2006-2007. Setting/Participants Community-based study of 37 healthy, initially underactive adults aged 50 years and older who were randomized and completed the 8-week study (intervention=19, control=18). Intervention Participants received an instructional session and a PDA programmed to monitor their physical activity levels twice per day and provide daily and weekly individualized feedback, goal setting, and support. Controls received standard, age-appropriate written physical activity educational materials. Main Outcome Measure Physical activity was assessed via the Community Healthy Activities Model Program for Seniors (CHAMPS) questionnaire at baseline and 8 weeks. Results Relative to controls, intervention participants reported significantly greater 8-week mean estimated caloric expenditure levels and minutes per week in MOD+ activity (p<0.04). Satisfaction with the PDA was reasonably high in this largely PDA-naive sample. Conclusions Results from this first-generation study indicate that hand-held computers may be effective tools for increasing initial physical activity levels among underactive adults. PMID:18201644

Education Outreach at M.I.T. Plasma Science and Fusion Center

NASA Astrophysics Data System (ADS)

Rivenberg, P.; Censabella, V.

2000-10-01

At the MIT PSFC student and staff volunteers work together to increase the public's knowledge of fusion and plasma-related experiments. Seeking to generate excitement about science, engineering and mathematics, the PSFC holds a number of outreach activities throughout the year, including Middle and High School Outreach Days and the Mr. Magnet program. During the past year, in collaboration with the MIT Museum, the PSFC reprogrammed their C-Mod, Jr Video Game to be operated via the keyboard instead of joysticks. The game will eventually be available on the web and on disc. The PSFC maintains a Home Page on the World Wide Web, which can be reached at http://www.psfc.mit.edu.

Identification of functional elements and regulatory circuits by Drosophila modENCODE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roy, Sushmita; Ernst, Jason; Kharchenko, Peter V.

2010-12-22

To gain insight into how genomic information is translated into cellular and developmental programs, the Drosophila model organism Encyclopedia of DNA Elements (modENCODE) project is comprehensively mapping transcripts, histone modifications, chromosomal proteins, transcription factors, replication proteins and intermediates, and nucleosome properties across a developmental time course and in multiple cell lines. We have generated more than 700 data sets and discovered protein-coding, noncoding, RNA regulatory, replication, and chromatin elements, more than tripling the annotated portion of the Drosophila genome. Correlated activity patterns of these elements reveal a functional regulatory network, which predicts putative new functions for genes, reveals stage- andmore » tissue-specific regulators, and enables gene-expression prediction. Our results provide a foundation for directed experimental and computational studies in Drosophila and related species and also a model for systematic data integration toward comprehensive genomic and functional annotation. Several years after the complete genetic sequencing of many species, it is still unclear how to translate genomic information into a functional map of cellular and developmental programs. The Encyclopedia of DNA Elements (ENCODE) (1) and model organism ENCODE (modENCODE) (2) projects use diverse genomic assays to comprehensively annotate the Homo sapiens (human), Drosophila melanogaster (fruit fly), and Caenorhabditis elegans (worm) genomes, through systematic generation and computational integration of functional genomic data sets. Previous genomic studies in flies have made seminal contributions to our understanding of basic biological mechanisms and genome functions, facilitated by genetic, experimental, computational, and manual annotation of the euchromatic and heterochromatic genome (3), small genome size, short life cycle, and a deep knowledge of development, gene function, and chromosome biology. The functions of {approx}40% of the protein and nonprotein-coding genes [FlyBase 5.12 (4)] have been determined from cDNA collections (5, 6), manual curation of gene models (7), gene mutations and comprehensive genome-wide RNA interference screens (8-10), and comparative genomic analyses (11, 12). The Drosophila modENCODE project has generated more than 700 data sets that profile transcripts, histone modifications and physical nucleosome properties, general and specific transcription factors (TFs), and replication programs in cell lines, isolated tissues, and whole organisms across several developmental stages (Fig. 1). Here, we computationally integrate these data sets and report (i) improved and additional genome annotations, including full-length proteincoding genes and peptides as short as 21 amino acids; (ii) noncoding transcripts, including 132 candidate structural RNAs and 1608 nonstructural transcripts; (iii) additional Argonaute (Ago)-associated small RNA genes and pathways, including new microRNAs (miRNAs) encoded within protein-coding exons and endogenous small interfering RNAs (siRNAs) from 3-inch untranslated regions; (iv) chromatin 'states' defined by combinatorial patterns of 18 chromatin marks that are associated with distinct functions and properties; (v) regions of high TF occupancy and replication activity with likely epigenetic regulation; (vi)mixed TF and miRNA regulatory networks with hierarchical structure and enriched feed-forward loops; (vii) coexpression- and co-regulation-based functional annotations for nearly 3000 genes; (viii) stage- and tissue-specific regulators; and (ix) predictive models of gene expression levels and regulator function.« less

MOD: An In-Situ Organic Detector for the MSR 2003 Mission

NASA Technical Reports Server (NTRS)

Kminek, G.; Bada, J. L.; Botta, O.; Glavin, D. P.; Grunthaner, F. J.; LaBaw, C. C.; Serviss, O. E.

2000-01-01

Looking for organic compounds that are essential for biochemistry or indicative of extraterrestrial organic influx is the primary goal of MOD (Mars Organic Detector). MOD can also quantify adsorbed and chemisorbed water and evolved carbon dioxide.

Targeting Extracellular Histones with Novel RNA Bio drugs for the Treatment of Acute Lung Injury

DTIC Science & Technology

2017-10-01

organ involved in MODS is the lung (referred to as acute respiratory distress syndrome or ARDS). Trauma, smoke inhalation, burns, radiation , severe...and mortality associated with multiple organ dysfunction/ acute respiratory distress syndrome (MODS/ARDS) and ALI that can be easily delivered in combat...MODS, the risk of death is 40%. The most common organ involved in MODS is the lungs (referred to as acute respiratory distress syndrome or ARDS

Feasibility of using auto Mod-MPI system, a novel technique for automated measurement of fetal modified myocardial performance index.

PubMed

Lee, M-Y; Won, H-S; Jeon, E-J; Yoon, H C; Choi, J Y; Hong, S J; Kim, M-J

2014-06-01

To evaluate the reproducibility of measurement of the fetal left modified myocardial performance index (Mod-MPI) determined using a novel automated system. This was a prospective study of 116 ultrasound examinations from 110 normal singleton pregnancies at 12 + 1 to 37 + 1 weeks' gestation. Two experienced operators each measured the left Mod-MPI twice manually and twice automatically using the Auto Mod-MPI system. Intra- and interoperator reproducibility were assessed using intraclass correlation coefficients (ICCs) and the manual and automated measurements obtained by the more experienced operator were compared using Bland-Altman plots and ICCs. Both operators successfully measured the left Mod-MPI in all cases using the Auto Mod-MPI system. For both operators, intraoperator reproducibility was higher when performing automated measurements (ICC = 0.967 and 0.962 for Operators 1 and 2, respectively) than when performing manual measurements (ICC = 0.857 and 0.856 for Operators 1 and 2, respectively). Interoperator agreement was also better for automated than for manual measurements (ICC = 0.930 vs 0.723, respectively). There was good agreement between the automated and manual values measured by the more experienced operator. The Auto Mod-MPI system is a reliable technique for measuring fetal left Mod-MPI and demonstrates excellent reproducibility. Copyright © 2013 ISUOG. Published by John Wiley & Sons Ltd.

Specific etiologies associated with the multiple organ dysfunction syndrome in children: Part 2

PubMed Central

Upperman, Jeffrey S.; Bucuvalas, John C.; Williams, Felicia N.; Cairns, Bruce A.; Cox, Charles S.; Doctor, Allan; Tamburro, Robert F.

2016-01-01

Objective To describe a number of conditions and therapies associated with multiple organ dysfunction syndrome (MODS) presented as part of the Eunice Kennedy Shriver National Institute of Child Health and Human Development MODS Workshop (March 26–27, 2015). In addition, the relationship between burn injuries and MODS is also included although it was not discussed at the Workshop. Data Sources Literature review, research data, and expert opinion. Study Selection Not applicable. Data Extraction Moderated by an expert from the field, issues relevant to the association of MODS with a variety of conditions and therapies were presented, discussed and debated with a focus on identifying knowledge gaps and research priorities. Data Synthesis Summary of presentations and discussion supported and supplemented by relevant literature. Conclusions Sepsis and trauma are the two conditions most commonly associated with MODS both in children and adults. However, many other pathophysiologic processes may result in MODS. In this paper, we discuss conditions such as liver failure and pancreatitis, pathophysiologic processes such as ischemia and hypoxia, and injuries such as trauma and burns. Additionally, therapeutic interventions such as medications, blood transfusions, transplantation may also precipitate and contribute to MODS. The purpose of this manuscript is to describe the association of MODS with a variety of conditions and therapies in an attempt to identify similarities, differences and opportunities for therapeutic intervention. PMID:28248835

COMPARISON OF DIFFERENT TRUNK ENDURANCE TESTING METHODS IN COLLEGE‐AGED INDIVIDUALS

PubMed Central

Krier, Amber D.; Nelson, Julie A.; Rogers, Michael A.; Stuke, Zachariah O.; Smith, Barbara S.

2012-01-01

Objective: Determine the reliability of two different modified (MOD1 and MOD2) testing methods compared to a standard method (ST) for testing trunk flexion and extension endurance. Participants: Twenty‐eight healthy individuals (age 26.4 ± 3.2 years, height 1.75 ± m, weight 71.8 ± 10.3 kg, body mass index 23.6 ± 3.4 m/kg2). Method: Trunk endurance time was measured in seconds for flexion and extension under the three different stabilization conditions. The MOD1 testing procedure utilized a female clinician (70.3 kg) and MOD2 utilized a male clinician (90.7 kg) to provide stabilization as opposed to the ST method of belt stabilization. Results: No significant differences occurred between flexion and extension times. Intraclass correlations (ICCs3,1) for the different testing conditions ranged from .79 to .95 (p <.000) and are found in Table 3. Concurrent validity using the ST flexion times as the gold standard coefficients were .95 for MOD1 and .90 for MOD2. For ST extension, coefficients were .91 and .80, for MOD1 and MOD2 respectively (p <.01). Conclusions: These methods proved to be a reliable substitute for previously accepted ST testing methods in normal college‐aged individuals. These modified testing procedures can be implemented in athletic training rooms and weight rooms lacking appropriate tables for the ST testing. Level of Evidence: 3 PMID:23091786

Space allowance influences individually housed Holstein bull calf innate immune measures and standing behaviors after castration at 3 weeks of age.

PubMed

Calvo-Lorenzo, M S; Hulbert, L E; Ballou, M A; Fowler, A L; Luo, Y; Klasing, K C; Mitloehner, F M

2017-03-01

Dairy calves in the Southwest regions of the United States are typically raised individually in wooden hutches with 1.23 m 2 of space. The objective of the study was to determine if increased space allowance in wooden hutches influences measures of innate immunity and behaviors of Holstein bull calves pre- and postcastration. Calves were randomly assigned at 4 d of age to conventional (CONV; 1.23 m 2 of space; n = 18), moderate (MOD; 1.85 m 2 space; n = 17), or maximized space allowance (MAX; 3.71 m 2 space; n = 19) in hutches. Calves were surgically castrated at 24 d of age. Peripheral whole blood samples were collected at -1, +1, +5, and +12 d of castration. Accelerometer loggers (n = 16 calves per treatment) were used from -3 to +5 d of castration to assess standing behaviors. All calves decreased total standing duration the day of castration versus precastration. Overall, MAX spent the most time in the stand position postcastration versus CONV and MOD. Within treatments, MOD and MAX had increased plasma cortisol 1 d postcastration versus precastration. A treatment × time tendency was observed for cortisol at 12 d postcastration; MAX had the least circulating cortisol. A treatment × time tendency for circulating haptoglobin (Hp) was observed and Hp was greatest among CONV 1 d pre- and 12 d postcastration. Compared with precastration, CONV had increased Hp at 1, 5, and 12 d, whereas MOD had increased Hp at 5 d, and Hp remained similar within MAX. A treatment × time tendency for tumor necrosis factor-α (TNF-α) from lipopolysaccharide-stimulated whole blood was observed; at 1 d postcastration, MOD had the most TNF-α, whereas MAX had the least. Within MAX, calves had increased TNF-α from precastration to 5 d postcastration. A treatment × time interaction was observed for whole blood bactericidal activity against Escherichia coli (WB anti-E). The CONV tended to have the greatest WB anti-E at d -1, but at d 1 and 5 postcastration, CONV had the least WB anti-E. Overall, MAX had less intensity of neutrophil oxidative burst versus CONV and MOD. The lower response of neutrophil oxidative burst and slower Hp secretion after castration is indicative that the wound site likely had less microbial exposure. The findings of this study suggest that calves housed with more space are potentially at less risk of too much inflammation after castration, which may likely be due to the effects of increased space on hide cleanliness and increased standing time. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Analyses of requirements for computer control and data processing experiment subsystems: Image data processing system (IDAPS) software description (7094 version), volume 2

NASA Technical Reports Server (NTRS)

1973-01-01

A description of each of the software modules of the Image Data Processing System (IDAPS) is presented. The changes in the software modules are the result of additions to the application software of the system and an upgrade of the IBM 7094 Mod(1) computer to a 1301 disk storage configuration. Necessary information about IDAPS sofware is supplied to the computer programmer who desires to make changes in the software system or who desires to use portions of the software outside of the IDAPS system. Each software module is documented with: module name, purpose, usage, common block(s) description, method (algorithm of subroutine) flow diagram (if needed), subroutines called, and storage requirements.

Clinical and paraclinical profile, and predictors of outcome in 90 cases of scrub typhus, Meghalaya, India.

PubMed

Sivarajan, Sunuraj; Shivalli, Siddharudha; Bhuyan, Debomallya; Mawlong, Michael; Barman, Rittwick

2016-10-05

India is an integral component of "tsutsugamushi triangle" which depicts a part of the globe endemic to scrub typhus. Owing to frequent outbreaks witnessed in different parts of the country in the recent past, scrub typhus is described as a re-emerging infectious disease in India. The present study aimed to study the clinical and paraclinical profile, complications and predictors of outcome among 90 cases of scrub typhus diagnosed in a hospital of north-eastern India from Sept 2011 to Aug 2012. A longitudinal study was conducted in a hospital of Meghalaya, India between Sept 2011 and Aug 2012. Diagnosis of scrub typhus was arrived by SD BIOLINE tsutsugamushi (solid phase immunochromatographic assay) rapid diagnostic test for antibodies (IgM, IgG or IgA). Descriptive analyses of age, gender, geographic area, symptoms and signs, treatment, laboratory findings, complications, and outcome were conducted. Relative risk (RR) with 95 % confidence interval (CI) was computed for Multiple Organ Dysfunction Syndrome (MODS) and mortality. Binary logistic regression was applied to the significant correlates (P < 0.05) on univariate analysis to identify the predictors of MODS and mortality in scrub typhus. As many as 662 clinically suspected scrub typhus patients were tested and 90 (13.6 %) were diagnosed to have scrub typhus. Out of 90 patients, 52.2 % (n = 47) were males and their mean (SD) age was 36.29 (13.38) years. Fever of <7 days (n = 75, 83.3 %), myalgia (n = 56, 62.2 %), pain abdomen (n = 24, 26.7 %), headache (n = 24, 26.7 %), nausea/vomiting (n = 21, 23.3 %), dry cough (n = 21, 23.3 %), hepatomegaly (n = 24, 26.7 %), splenomegaly (n = 22, 24.4 %), and lymphadenopathy (n = 20, 22.2 %) were the predominant clinical features. Eschar was seen in 10 patients (11.1 %). One third (n = 30) of the patients developed at least one systemic complication. Acute hepatitis (n = 15, 16.7 %), pneumonitis (n = 14, 15.6 %), and acute kidney injury (n = 11, 12.2 %) were the common complications. MODS was seen in 14.4 % (n = 13) and 38.5 % (n = 5) of the patients with MODS died. Overall, case fatality rate was 5.15 % (n = 5). On univariate analysis, platelets <100 000/mm 3 , serum creatinine >1.5 mg/dl, and transaminase (AST, ALT or both) >500 U/L were associated with MODS (P < 0.001) and mortality (P < 0.05). In addition, serum bilirubin >3 mg/dl was also associated with MODS (P < 0.001). On applying binary logistic regression, serum creatinine >1.5 mg/dl was a predictor of MODS (OR: 76.1, 95 % CI: 4.9-1175.6) and mortality (OR: 18.03, 95 % CI: 1.38-235.1). In this study setting, approximately one-seventh (13.6 %) of the acute undifferentiated febrile illness were due to scrub typhus. Systemic complications were common (33.3 %). Serum creatinine >1.5 mg/dl was a predictor of MODS and mortality.

Validation of microscopic observation drug susceptibility testing for rapid, direct rifampicin and isoniazid drug susceptibility testing in patients receiving tuberculosis treatment

PubMed Central

Coronel, J; Roper, M H; Herrera, C; Bonilla, C; Jave, O; Gianella, C; Sabogal, I; Huancaré, V; Leo, E; Tyas, A; Mendoza-Ticona, A; Caviedes, L; Moore, D A J; Drancourt, M

2014-01-01

Drug susceptibility testing (DST) is often needed in patients clinically failing tuberculosis (TB) therapy. Most studies of phenotypic direct drug susceptibility tests, such as microscopic observation drug susceptibility (MODS) tests, have been performed in patients not receiving TB treatment. The effect of ongoing TB treatment on the performance of MODS direct DST has not been previously explored, but patients failing such therapy constitute an important target group. The aim of this study was to determine the performance of MODS direct rifampicin and isoniazid DST in patients clinically failing first-line TB treatment, and to compare MODS direct DST with indirect proportion method DST. Sputa from 264 TB patients were cultured in parallel in Lowenstein–Jensen (LJ) and MODS assays; strains were tested for rifampicin and isoniazid susceptibility by the proportion method at the national reference laboratory. Ninety-three samples were culture-positive by LJ and MODS (concordance of 96%; kappa 0.92). With conventional MODS plate DST reading (performed on the same day as the sample is classified as culture-positive), the isoniazid DST concordance was 96.8% (kappa 0.89), and the concordance for rifampicin susceptibility testing was 92.6% (kappa 0.80). Reading of MODS DST plates 1 week after cultures had been determined to be culture-positive improved overall performance marginally—the isoniazid DST concordance was 95.7% (kappa 0.85); and the rifampicin DST concordance was 96.8% (kappa 0.91). Sensitivity for detection of multidrug-resistant TB was 95.8%. MODS testing provided reliable rifampicin and isoniazid DST results for samples obtained from patients receiving TB therapy. A modified DST reading schedule for such samples, with a final reading 1 week after a MODS culture turns positive, marginally improves the concordance with reference DST. PMID:24107197

Automotive Stirling Engine Development Project

NASA Technical Reports Server (NTRS)

Ernst, William D.; Shaltens, Richard K.

1997-01-01

The development and verification of automotive Stirling engine (ASE) component and system technology is described as it evolved through two experimental engine designs: the Mod 1 and the Mod 2. Engine operation and performance and endurance test results for the Mod 1 are summarized. Mod 2 engine and component development progress is traced from the original design through hardware development, laboratory test, and vehicle installation. More than 21,000 hr of testing were accomplished, including 4800 hr with vehicles that were driven more dm 59,000 miles. Mod 2 engine dynamometer tests demonstrated that the engine system configuration had accomplished its performance goals for power (60 kW) and efficiency (38.5%) to within a few percent. Tests with the Mod 2 engine installed in a delivery van demonstrated combined metro-highway fuel economy improvements consistent with engine performance goals and the potential for low emission levels. A modified version of the Mod 2 has been identified as a manufacturable design for an ASE. As part of the ASE project, the Industry Test and Evaluation Program (ITEP), NASA Technology Utilization (TU) project, and the industry-funded Stirling Natural Gas Engine program were undertaken to transfer ASE technology to end users. The results of these technology transfer efforts are also summarized.

Symmetric products of a real curve and the moduli space of Higgs bundles

NASA Astrophysics Data System (ADS)

Baird, Thomas John

2018-03-01

Consider a Riemann surface X of genus g ≥ 2 equipped with an antiholomorphic involution τ. This induces a natural involution on the moduli space M(r , d) of semistable Higgs bundles of rank r and degree d. If D is a divisor such that τ(D) = D, this restricts to an involution on the moduli space M(r , D) of those Higgs bundles with fixed determinant O(D) and trace-free Higgs field. The fixed point sets of these involutions M(r , d) τ and M(r , D) τ are (A , A , B) -branes introduced by Baraglia and Schaposnik (2016). In this paper, we derive formulas for the mod 2 Betti numbers of M(r , d) τ and M(r , D) τ when r = 2 and d is odd. In the course of this calculation, we also compute the mod 2 cohomology ring of Symm(X) τ, the fixed point set of the involution induced by τ on symmetric products of the Riemann surface.

USGS Map-on-Demand Printing

USGS Publications Warehouse

,

1999-01-01

Currently, the U.S. Geological Survey (USGS) uses conventional lithographic printing techniques to produce paper copies of most of its mapping products. This practice is not economical for those products that are in low demand. With the advent of newer technologies, high-speed, large-format printers have been coupled with innovative computer software to turn digital map data into a printed map. It is now possible to store and retrieve data from vast geospatial data bases and print a map on an as-needed basis; that is, print on demand, thereby eliminating the need to warehouse an inventory of paper maps for which there is low demand. Using print-on-demand technology, the USGS is implementing map-on-demand (MOD) printing for certain infrequently requested maps. By providing MOD, the USGS can offer an alternative to traditional, large-volume printing and can improve its responsiveness to customers by giving them greater access to USGS scientific data in a format that otherwise might not be available.

Validation Database Based Thermal Analysis of an Advanced RPS Concept

NASA Technical Reports Server (NTRS)

Balint, Tibor S.; Emis, Nickolas D.

2006-01-01

Advanced RPS concepts can be conceived, designed and assessed using high-end computational analysis tools. These predictions may provide an initial insight into the potential performance of these models, but verification and validation are necessary and required steps to gain confidence in the numerical analysis results. This paper discusses the findings from a numerical validation exercise for a small advanced RPS concept, based on a thermal analysis methodology developed at JPL and on a validation database obtained from experiments performed at Oregon State University. Both the numerical and experimental configurations utilized a single GPHS module enabled design, resembling a Mod-RTG concept. The analysis focused on operating and environmental conditions during the storage phase only. This validation exercise helped to refine key thermal analysis and modeling parameters, such as heat transfer coefficients, and conductivity and radiation heat transfer values. Improved understanding of the Mod-RTG concept through validation of the thermal model allows for future improvements to this power system concept.

Improving the Incoherence of a Learned Dictionary via Rank Shrinkage.

PubMed

Ubaru, Shashanka; Seghouane, Abd-Krim; Saad, Yousef

2017-01-01

This letter considers the problem of dictionary learning for sparse signal representation whose atoms have low mutual coherence. To learn such dictionaries, at each step, we first update the dictionary using the method of optimal directions (MOD) and then apply a dictionary rank shrinkage step to decrease its mutual coherence. In the rank shrinkage step, we first compute a rank 1 decomposition of the column-normalized least squares estimate of the dictionary obtained from the MOD step. We then shrink the rank of this learned dictionary by transforming the problem of reducing the rank to a nonnegative garrotte estimation problem and solving it using a path-wise coordinate descent approach. We establish theoretical results that show that the rank shrinkage step included will reduce the coherence of the dictionary, which is further validated by experimental results. Numerical experiments illustrating the performance of the proposed algorithm in comparison to various other well-known dictionary learning algorithms are also presented.

Viewpoints, Formalisms, Languages, and Tools for Cyber-Physical Systems

DTIC Science & Technology

2014-05-16

Organization]: Special-Purpose and Application-Based Systems —real-time and embedded sys- tems; F.1.2 [Computation by Abstract Devices]: Mod- els of...domain CPS is not new. For example, early automotive embedded systems in the 1970s already combined closed-loop control of the brake and engine subsystems...Consider for example the development of an embedded control system such as an advanced driver assistance system (ADAS) (e.g., adaptive cruise control

40 CFR Appendix V to Part 86 - The Standard Road Cycle (SRC)

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Pt. 86, App. V... engine) Idle 10 sec 0 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to 20 MPH −5 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to stop −5 1 Idle 5 sec 0 1...

40 CFR Appendix V to Part 86 - The Standard Road Cycle (SRC)

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Pt. 86, App. V... engine) Idle 10 sec 0 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to 20 MPH −5 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to stop −5 1 Idle 5 sec 0 1...

40 CFR Appendix V to Part 86 - The Standard Road Cycle (SRC)

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Pt. 86, App. V Appendix V... engine) Idle 10 sec 0 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to 20 MPH −5 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to stop −5 1 Idle 5 sec 0 1...

Twenty Years of Research on the Alcator C-Mod Tokamak

NASA Astrophysics Data System (ADS)

Greenwald, Martin

2013-10-01

Alcator C-Mod is a compact, high-field tokamak, whose unique design and operating parameters have produced a wealth of new and important results since its start in 1993, contributing data that extended tests of critical physical models into new parameter ranges and into new regimes. Using only RF for heating and current drive with innovative launching structures, C-Mod operates routinely at very high power densities. Research highlights include direct experimental observation of ICRF mode-conversion, ICRF flow drive, demonstration of Lower-Hybrid current drive at ITER-like densities and fields and, using a set of powerful new diagnostics, extensive validation of advanced RF codes. C-Mod spearheaded the development of the vertical-target divertor and has always operated with high-Z metal plasma facing components--an approach adopted for ITER. C-Mod has made ground-breaking discoveries in divertor physics and plasma-material interactions at reactor-like power and particle fluxes and elucidated the critical role of cross-field transport in divertor operation, edge flows and the tokamak density limit. C-Mod developed the I-mode and EDA H-mode regimes which have high performance without large ELMs and with pedestal transport self-regulated by short-wavelength electromagnetic waves. C-Mod has carried out pioneering studies of intrinsic rotation and found that self-generated flow shear can be strong enough to significantly modify transport. C-Mod made the first quantitative link between pedestal temperature and H-mode performance, showing that the observed self-similar temperature profiles were consistent with critical-gradient-length theories and followed up with quantitative tests of nonlinear gyrokinetic models. Disruption studies on C-Mod provided the first observation of non-axisymmetric halo currents and non-axisymmetric radiation in mitigated disruptions. Work supported by U.S. DoE

Mission Operations Directorate - Success Legacy of the Space Shuttle Program (Overview of the Evolution and Success Stories from MOD During the Space Shuttle program)

NASA Technical Reports Server (NTRS)

Azbell, Jim A.

2011-01-01

In support of the Space Shuttle Program, as well as NASA's other human space flight programs, the Mission Operations Directorate (MOD) at the Johnson Space Center has become the world leader in human spaceflight operations. From the earliest programs - Mercury, Gemini, Apollo - through Skylab, Shuttle, ISS, and our Exploration initiatives, MOD and its predecessors have pioneered ops concepts and emphasized a history of mission leadership which has added value, maximized mission success, and built on continual improvement of the capabilities to become more efficient and effective. This paper provides specific examples that illustrate how MOD's focus on building and contributing value with diverse teams has been key to their successes both with the US space industry and the broader international community. This paper will discuss specific examples for the Plan, Train, Fly, and Facilities aspects within MOD. This paper also provides a discussion of the joint civil servant/contractor environment and the relative badge-less society within MOD. Several Shuttle mission related examples have also been included that encompass all of the aforementioned MOD elements and attributes, and are used to show significant MOD successes within the Shuttle Program. These examples include the STS-49 Intelsat recovery and repair, the (post-Columbia accident) TPS inspection process and the associated R-Bar Pitch Maneuver for ISS missions, and the STS-400 rescue mission preparation efforts for the Hubble Space Telescope repair mission. Since their beginning, MOD has consistently demonstrated their ability to evolve and respond to an ever changing environment, effectively prepare for the expected and successfully respond to the unexpected, and develop leaders, expertise, and a culture that has led to mission and Program success.

Microcolony culture techniques for tuberculosis diagnosis: a systematic review.

PubMed

Leung, E; Minion, J; Benedetti, A; Pai, M; Menzies, D

2012-01-01

There is considerable demand for quicker and more affordable yet accurate diagnostic tools for tuberculosis (TB). The microscopic observation drug susceptibility (MODS) assay and the thin-layer agar (TLA) assay are inexpensive, rapid microcolony-based culture methods. A systematic review and meta-analysis was performed to assess the accuracy and other test characteristics of MODS and TLA compared to a reference standard of traditional solid or liquid culture. Pooled estimates of sensitivity and specificity and their 95% confidence intervals were estimated with an exact binomial likelihood random effects meta-analysis. A total of 21 eligible studies were identified, 12 that evaluated MODS, seven that evaluated TLA and two that evaluated both. The overall pooled sensitivity and specificity of MODS were respectively 92% (95%CI 87-97) and 96% (90-100), and for TLA they were respectively 87% (95%CI 79-94) and 98% (95%CI 94-100), although there was considerable heterogeneity of results. When the studies were restricted to those assessing accuracy of MODS in sputum samples only, the sensitivity was 96% (95%CI 94-98) and the specificity 96% (95%CI 89-100). The mean intervals from reception of specimens to results were 9.2 days with MODS and 11.5 days with TLA; contamination rates averaged 6.6% with MODS and 12.3% with TLA; materials and supplies costs averaged US$1.48 for MODS and US$2.42 for TLA. MODS and TLA appear to be accurate and rapid yet inexpensive diagnostic tools for active TB. However, this review did not find sufficient evidence on the feasibility and costs of implementation of these tests, nor on the impact of these tests on patient outcomes.

TOPICAL REVIEW: Review of a chemical approach to YBa2Cu3O7-x-coated superconductors—metalorganic deposition using trifluoroacetates

NASA Astrophysics Data System (ADS)

Araki, Takeshi; Hirabayashi, Izumi

2003-11-01

Large-area, uniform, high critical current density (Jc) YBa2Cu3O7-x (YBCO) superconductor films are now routinely obtained by metalorganic deposition using trifluoroacetates (TFA-MOD). This method does not require any expensive vacuum apparatus at any time during the whole process. Thus, TFA-MOD is regarded as one of the most suitable candidates for fabricating a YBCO tape for many high-power applications. This method originated from an electron beam process using BaF2 developed by Mankiewich et al. Afterwards, Gupta et al reported using TFA-MOD to prepare a similar precursor film. These two ex situ processes used fluorides instead of BaCO3 to avoid the fatal deterioration in Jc, which is caused in the resulting films through metal carboxylic groups. Fluorides not only avoid such deterioration but also lead to perfectly c-axis-oriented epitaxial crystal growth. In conventional metalorganic deposition, nucleation in the precursor film causes random orientation in the resulting film. However, in TFA-MOD, nanocrystallites in the precursor film never cause such disorder. Furthermore, during the firing process of TFA-MOD, water and HF gas diffuse quickly between the film surface and growth front of the YBCO layer. This diffusion never limits the growth rate of YBCO. What distinguishes TFA-MOD from conventional metalorganic deposition? What happens during heat treatment? In this paper, we discuss all the TFA-MOD processes and the peculiar growth scheme of the YBCO layer in TFA-MOD using the model of a quasi-liquid network. In addition, we review the history of TFA-MOD and recent results and discuss the prospects of future applications.

Large wind turbine generators. [NASA program status and potential costs

NASA Technical Reports Server (NTRS)

Thomas, R. L.; Donovon, R. M.

1978-01-01

The large wind turbine portion of the Federal Wind Energy Program consists of two major project efforts: (1) the Mod-0 test bed project for supporting research technology, and (2) the large experimental wind turbines for electric utility applications. The Mod-0 has met its primary objective of providing the entire wind energy program with early operations and performance data. The large experimental wind turbines to be tested in utility applications include three of the Mod-0A (200 kW) type, one Mod-1 (2000 kW), and possibly several of the Mod-2 (2500 kW) designs. This paper presents a description of these wind turbine systems, their programmatic status, and a summary of their potential costs.

Operational results for the experimental DOE/NASA Mod-OA wind turbine project

NASA Astrophysics Data System (ADS)

Shaltens, R. K.; Birchenough, A. G.

The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

Operational results for the experimental DOE/NASA Mod-OA wind turbine project

NASA Technical Reports Server (NTRS)

Shaltens, R. K.; Birchenough, A. G.

1983-01-01

The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

Development of Integration Framework for Sensor Network and Satellite Image based on OGC Web Services

NASA Astrophysics Data System (ADS)

Ninsawat, Sarawut; Yamamoto, Hirokazu; Kamei, Akihide; Nakamura, Ryosuke; Tsuchida, Satoshi; Maeda, Takahisa

2010-05-01

With the availability of network enabled sensing devices, the volume of information being collected by networked sensors has increased dramatically in recent years. Over 100 physical, chemical and biological properties can be sensed using in-situ or remote sensing technology. A collection of these sensor nodes forms a sensor network, which is easily deployable to provide a high degree of visibility into real-world physical processes as events unfold. The sensor observation network could allow gathering of diverse types of data at greater spatial and temporal resolution, through the use of wired or wireless network infrastructure, thus real-time or near-real time data from sensor observation network allow researchers and decision-makers to respond speedily to events. However, in the case of environmental monitoring, only a capability to acquire in-situ data periodically is not sufficient but also the management and proper utilization of data also need to be careful consideration. It requires the implementation of database and IT solutions that are robust, scalable and able to interoperate between difference and distributed stakeholders to provide lucid, timely and accurate update to researchers, planners and citizens. The GEO (Global Earth Observation) Grid is primarily aiming at providing an e-Science infrastructure for the earth science community. The GEO Grid is designed to integrate various kinds of data related to the earth observation using the grid technology, which is developed for sharing data, storage, and computational powers of high performance computing, and is accessible as a set of services. A comprehensive web-based system for integrating field sensor and data satellite image based on various open standards of OGC (Open Geospatial Consortium) specifications has been developed. Web Processing Service (WPS), which is most likely the future direction of Web-GIS, performs the computation of spatial data from distributed data sources and returns the outcome in a standard format. The interoperability capabilities and Service Oriented Architecture (SOA) of web services allow incorporating between sensor network measurement available from Sensor Observation Service (SOS) and satellite remote sensing data from Web Mapping Service (WMS) as distributed data sources for WPS. Various applications have been developed to demonstrate the efficacy of integrating heterogeneous data source. For example, the validation of the MODIS aerosol products (MOD08_D3, the Level-3 MODIS Atmosphere Daily Global Product) by ground-based measurements using the sunphotometer (skyradiometer, Prede POM-02) installed at Phenological Eyes Network (PEN) sites in Japan. Furthermore, the web-based framework system for studying a relationship between calculated Vegetation Index from MODIS satellite image surface reflectance (MOD09GA, the Surface Reflectance Daily L2G Global 1km and 500m Product) and Gross Primary Production (GPP) field measurement at flux tower site in Thailand and Japan has been also developed. The success of both applications will contribute to maximize data utilization and improve accuracy of information by validate MODIS satellite products using high degree of accuracy and temporal measurement of field measurement data.

ISSLive!

NASA Technical Reports Server (NTRS)

Price, Jennifer B.; Snook, Bryan

2011-01-01

The ISSLive! project is a JSC innovation award- winning, combined MOD/Education project to publish export control and PAO-approved ISS telemetry, and simplified and scrubbed crew timelines. The publication of this data will be real-time or near real time and will include links to the crew's social media feeds and existing streaming public video/audio feeds, via public-friendly website, mobile devices and tablet applications. Additionally, the project will offer interactive virtual 3D views of an ISS model based on real-time telemetry and a 3D virtual mission control center based on existing Front Room console positions in made for public displays. The ISSLive! project is MOD-managed and includes collaborations with subject-matter expertise from the ISS flight controllers regarding daily operations and planning, education program specialists from the JSC Office of Education, instructional designers, human computer interface experts, and software/hardware experts from MOD facility organization, and senior web designers. In support of the Agency s Strategic Goal #6 with respect to using the ISS National Laboratory for education activities, ISSLive! uses the Station itself as STEM education subject matter and provides data for STEM-based lessons plans using national standards. Specifically, ISSLive! supports and enables the National Laboratory Education (NLE) project to address the Agency s Strategic Goal #6. This goal mandates, sharing NASA with the public, educators, and students to provide opportunities to participate in our Mission, foster innovation .. ISSLive! satisfies the Agency s outcomes of Strategic Goal; that is, engages the public in NASA's missions by providing new pathways for participation (Outcome 6.3) and it informs, engages, and inspires the public by sharing NASA s missions, challenges, and results (Outcome 6.4). Additionally, ISSLive! enables MOD s support of JSC Outreach and NASA's Open Data and Open Government Initiatives. The audience for the ISSLive! website and its application(s) are: teachers, students, citizen scientists, and the general public who will be given new and interactive insights on how the ISS Operates.

ModSAF-based development of operational requirements for light armored vehicles

NASA Astrophysics Data System (ADS)

Rapanotti, John; Palmarini, Marc

2003-09-01

Light Armoured Vehicles (LAVs) are being developed to meet the modern requirements of rapid deployment and operations other than war. To achieve these requirements, passive armour is minimized and survivability depends more on sensors, computers, countermeasures and communications to detect and avoid threats. The performance, reliability, and ultimately the cost of these systems, will be determined by the technology trends and the rates at which they mature. Defining vehicle requirements will depend upon an accurate assessment of these trends over a longer term than was previously needed. Modelling and simulation are being developed to study these long-term trends and how they contribute to establishing vehicle requirements. ModSAF is being developed for research and development, in addition to the original requirement of Simulation and Modelling for Acquisition, Rehearsal, Requirements and Training (SMARRT), and is becoming useful as a means for transferring technology to other users, researchers and contractors. This procedure eliminates the need to construct ad hoc models and databases. The integration of various technologies into a Defensive Aids Suite (DAS) can be designed and analyzed by combining field trials and laboratory data with modelling and simulation. ModSAF (Modular Semi-Automated Forces,) is used to construct the virtual battlefield and, through scripted input files, a "fixed battle" approach is used to define and implement contributions from three different sources. These contributions include: models of technology and natural phenomena from scientists and engineers, tactics and doctrine from the military and detailed analyses from operations research. This approach ensures the modelling of processes known to be important regardless of the level of information available about the system. Survivability of DAS-equipped vehicles based on future and foreign technology can be investigated by ModSAF and assessed relative to a test vehicle. A vehicle can be modelled phenomenologically until more information is available. These concepts and approach will be discussed in the paper.

Relative Throughput of the Near-IR Science Instruments for the James Webb Space Telescope as Measured During Ground Testing the Integrated Science Instrument Module

NASA Technical Reports Server (NTRS)

Malumuth, Eliot; Birkmann, Stephan; Kelly, Douglas M.; Kimble, Randy A.; Lindler, Don; Martel, Andre; Ohl, Raymond G.; Rieke, Marcia J.; Rowlands, Neil; Te Plate, Maurice

2016-01-01

Data were obtained for the purpose of measuring the relative throughput of the Near-IR Science Instruments (SIs) of the James Webb Space Telescope (JWST) as part of the second and third cryogenic-vacuum tests (CV2CV3) of the Integrated Science Instrument Module (ISIM) conducted at the Goddard Space Flight Center (GSFC) in 2014 and 20152016, at the beginning and end of the environmental test program, respectively. This Poster focuses on data obtained as part of the Initial Optical Baseline and as part of the Final Performance test -- two epochs that roughly bracket the CV3 test. The purpose of the test is to trend relative throughput to monitor for any potential changes from gross problems such as contamination or degradation of an optical element. Point source data were taken at a variety of wavelengths for NIRCam Module A and Module B, NIRSpec, NIRISS, Guider 1 and Guider 2 using the Laser Diode (LD) 1.06 micron, LD 1.55 micron, 2.1 micron LED and 3.5 micron LED, as well as for NIRCam Mod A and B and NIRISS using a tungsten source and the F277W, and F480M filters. Spectra were taken using the G140M, G235M, and G395M gratings for NIRSpec, the GRISMR grism for NIRCam Mod A and B and the GR150C grism for NIRISS. The results of these measurements are compared to what would be expected given the efficiency of each of the optical elements in each SI. Although these data were taken as a check against gross problems, they can also be used to provide the first relative throughput estimate for each SI through the various filters source wavelengths measured in their flight-like configurations.

Monitoring cropland evapotranspiration using MODIS products in Southern Brazil

NASA Astrophysics Data System (ADS)

Ruhoff, Anderson; Aparecida Moreira, Adriana; de Arruda Souza, Vanessa; Roberti, Debora Regina

2017-04-01

Evapotranspiration (ET), including water loss from plant transpiration and land evaporation, is of vital importance for understanding hydrological processes and climate dynamics. In this context, remote sensing is considered as the most important tool for estimate ET over large areas. The Moderate Resolution Imaging Spectroradiometer (MODIS) offers an interesting opportunity to evaluate ET with spatial resolution of 1 km. The MODIS global evapotranspiration algorithm (MOD16) considers both surface energy fluxes and climatic constraints on ET (water or temperature stress) to estimate plant transpiration and soil evaporation based on Penman-Monteith equation. The algorithm is driven by remotely sensed and reanalysis meteorological data. In this study, MOD16 algorithm was applied to the State of Rio Grande do Sul (in Southern Brazil) to analyse cropland and natural vegetation evapotranspiration and its impacts during drought events. We validated MOD16 estimations using eddy correlation measurements and water balance closure at monthly and annual time scales. We used observed discharge data from three large rivers in Southern Brazil (Jacuí, Taquari and Ibicuí), precipitation data from TRMM Multi-satellite Precipitation Analysis (3B43 version 7) and terrestrial water storage estimations from the Gravity Recovery and climate Experiment (GRACE). MOD16 algorithm detected evapotranspiration in different land use and land cover conditions. In cropland areas, the average evapotranspiration was 705 mm/y, while in pasture/grassland was 750 mm/y and in forest areas was 1099 mm/y. Compared to the annual water balance, evapotranspiration was underestimated, with mean relative errors between 8 and 30% and coefficients of correlation between 0.42 to 0.53. The water storage change (dS/dt) computed from the water balance closure at monthly time scales showed a significant correlation with the terrestrial water storage obtained from GRACE data, with a coefficient of correlation of 0.39 for the three basins evaluated. We also found a correspondence between evapotranspiration anomalies and the major drought events. The approach demonstrates the potential to evaluate evapotranspiration and water balance closure based on remote sensing data. Overall, MOD16 algorithm detected evapotranspiration over different land use and land cover conditions and is effective to monitor large areas. Acknowledgements: This work was made possible through the support of the Fundação de Amparo à Pesquisa do Estado do Rio Grande do Sul (FAPERGS).

The neurobiology of modafinil as an enhancer of cognitive performance and a potential treatment for substance use disorders

PubMed Central

Mereu, Maddalena; Bonci, Antonello; Newman, Amy Hauck; Tanda, Gianluigi

2013-01-01

Rationale and Objectives Modafinil (MOD) and its R-enantiomer (R-MOD) are approved medications for narcolepsy and other sleep disorders. They have also been used, off label, as cognitive enhancers in populations of patients with mental disorders, including substance abusers that demonstrate impaired cognitive function. A debated non-medical use of MOD in healthy individuals to improve intellectual performance is raising questions about its potential abuse liability in this population. Results and Conclusions MOD has low micromolar affinity for the dopamine transporter (DAT). Inhibition of dopamine (DA) reuptake via the DAT explains the enhancement of DA levels in several brain areas, an effect shared with psychostimulants like cocaine, methylphenidate and the amphetamines. However, its neurochemical effects and anatomical pattern of brain area activation differ from typical psychostimulants and are consistent with its beneficial effects on cognitive performance processes such as attention, learning, and memory. At variance with typical psychostimulants, MOD shows very low, if any, abuse liability, in spite of its use as a cognitive enhancer by otherwise healthy individuals. Finally, recent clinical studies have focused on the potential use of MOD as a medication for treatment of drug abuse, but have not shown consistent outcomes. However, positive trends in several result measures suggest that medications that improve cognitive function, like MOD or R-MOD, may be beneficial for treatment of substance use disorders in certain patient populations. PMID:23934211

The Motivic Cofiber of tau and Exotic Periodicities

NASA Astrophysics Data System (ADS)

Gheorghe, Bogdan

Consider the Tate twist tau epsilon H0,1 (S0,0) in the mod 2 cohomology of the motivic sphere. After 2-completion, the motivic Adams spectral sequence realizes this element as a map tau : S0,-1 → S0,0 . This thesis begins with the study of its cofiber, that we denote by Ctau. We first show that this motivic 2-cell complex can be endowed with a unique Einfinity ring structure. This promotes the known isomorphism pi *,* Ctau ≅ Ext *,* BP*BP (BP*, BP* ) to an isomorphism of rings which also preserves higher products. This structure allows us to consider its closed symmetric monoidal category of modules (Ctau Mod, - ∧Ctau -), which happens to live in the kernel of Betti realization. This category has surprising applications, and moreover contains many interesting motivic spectra. In particular, we construct exotic motivic fields K( wn), detecting motivic wn-periodicity. This theory of motivic wn-periodicity can be roughly seen as perpendicular to the vn-periodicity story, detected by the motivic Morava K-theories K( n). Finally, we also explain why the category Ctau Mod is so computable. The above isomor phism comes in a more structured version. In work that is joint with Zhouli Xu and Guozhen Wang, we show that there is an equivalence of infinity-categories Db ( MGL *,* MGL Comodev) ≅ → Ctau Cellcomp between an algebraic derived category, and the subcategory Ctau Cellcomp of cellular Ctau- modules that are complete with respect to a version of the algebraic cobordism spectrum MGL.

idRHa+ProMod - Rail Hardening Control System

NASA Astrophysics Data System (ADS)

Ferro, L.

2016-03-01

idRHa+ProMod is the process control system developed by Primetals Technologies to foresee the thermo-mechanical evolution and micro-structural composition of rail steels subjected to slack quenching into idRHa+ Rail Hardening equipments in a simulation environment. This tool can be used both off-line or in-line, giving the user the chance to test and study the best cooling strategies or letting the automatic control system free to adjust the proper cooling recipe. Optimization criteria have been tailored in order to determine the best cooling conditions according to the metallurgical requirements imposed by the main rail standards and also taking into account the elastoplastic bending phenomena occurring during all stages of the head hardening process. The computational core of idRHa+ProMod is a thermal finite element procedure coupled with special algorithms developed to work out the main thermo-physical properties of steel, to predict the non-isothermal austenite decomposition into all the relevant phases and subsequently to evaluate the amount of latent heat of transformation released, the compound thermal expansion coefficient and the amount of plastic deformation in the material. Air mist and air blades boundary conditions have been carefully investigated by means of pilot plant tests aimed to study the jet impingement on rail surfaces and the cooling efficiency at all working conditions. Heat transfer coefficients have been further checked and adjusted directly on field during commissioning. idRHa+ is a trademark of Primetals Technologies Italy Srl

78 FR 69805 - Periodic Reporting (Proposals Six Through Nine)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-21

... MODS Operation Groups for Productivity Calculations The Postal Service states that Proposal Eight would... MODS productivity data (TPF or TPH per workhour) for a variety of operation groups related to letter, flat, parcel, and bundle sorting. The MODS productivity data are used to parameterize a number of cost...

Moving Past "Hello World": Learning to Mod in an Online Affinity Space

ERIC Educational Resources Information Center

Subramanian, Shree Durga

2012-01-01

Game modding has increasingly become a mainstream and "cutting edge" medium to foster a broad range of critical software design and programming practices to learners coming from wide-ranging educational and professional backgrounds. Participatory practices, like game modding, are highly interest-driven and entail intense engagement with…

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Richey, A.; Farrell, R.; Riecke, G.; Ernst, W.; Howarth, R.; Cronin, M.; Simetkosky, M.; Smith, G.; Meacher, J.

1985-01-01

Development test activities on Mod I engines directed toward evaluating technologies for potential inclusion in the Mod II engine are summarized. Activities covered include: test of a 12-tube combustion gas recirculation combustor; manufacture and flow-distribution test of a two-manifold annular heater head; piston rod/piston base joint; single-solid piston rings; and a digital air/fuel concept. Also summarized are results of a formal assessment of candidate technologies for the Mod II engine, and preliminary design work for the Mod II. The overall program philosophy weight is outlined, and data and test results are presented.

A Literature Survey of Reverberation Modeling: With Emphasis on Bellhop Compatibility for Operational Applications

DTIC Science & Technology

2010-09-01

modèles à orientation opérationnelle ( comparativement à ceux orientés vers la recherche) qui pourraient être compatibles avec le modèle de propagation...concentre sur les modèles à orientation opérationnelle (en sacrifiant un certain degré d’exactitude pour accroître la réactivité, comparativement aux modèles...these modeling efforts are not applicable to Bellhop because they are designed specifically to take advantage of the normal mode decomposition

Lods, wrods, and mods: the interpretation of lod scores calculated under different models.

PubMed

Hodge, S E; Elston, R C

1994-01-01

In this paper we examine the relationships among classical lod scores, "wrod" scores (lod scores calculated under the wrong genetic model), and "mod" scores (lod scores maximized over genetic model parameters). We compare the behavior of these scores when the state of nature is linkage to their behavior when the state of nature is no linkage. We describe sufficient conditions for mod scores to be valid and discuss their use to determine the correct genetic model. We show that lod scores represent a likelihood-ratio test for independence. We explain the "ascertainment-assumption-free" aspect of using mod scores to determine mode of inheritance and we set this aspect into a well-established statistical framework. Finally, we summarize practical guidelines for the use of mod scores.

Clinical Predictors of Multiple Organ Dysfunction Syndromes in Pediatric patients with Scrub Typhus.

PubMed

Zhao, Dongying; Zhang, Yongjun; Yin, Zhaoqing; Zhao, Jing; Yang, Defeng; Zhou, Qun

2017-06-01

Scrub typhus can produce multiple organ dysfunction syndrome (MODS). Early recognition of the patients at risk of MODS would be helpful in providing timely management and reducing the mortality. In all, 449 children with scrub typhus were enrolled at three hospitals in Yunnan, China from January 2010 to January 2015. The patients' clinical status of organ system dysfunction was evaluated on the day of discharge from hospital by using standard criteria. The patients were classified into MODS present (64 cases, 14.3%) or MODS absent (385 cases, 85.7%). Multivariate logistic regression analyses revealed that the prognostic factors for MODS included skin rash (odds ratio, OR = 3.3, p = 0.037), time interval form treatment to defervescence (OR = 1.2, p = 0.035), hemoglobin (OR = 0.54, p = 0.041), platelet counts (OR = 0.06, p < 0.001), aspartate-aminotransferase (OR = 4.7, p = 0.011) and total bilirubin (OR = 2.3, p = 0.013). By describing risk factors resulting in MODS in pediatric scrub typhus, our study provides clinicians with important information to improve the clinical monitoring and prognostication of MODS. © The Author [2016]. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Association of low non-invasive near-infrared spectroscopic measurements during initial trauma resuscitation with future development of multiple organ dysfunction.

PubMed

Nicks, Bret A; Campons, Kevin M; Bozeman, William P

2015-01-01

Near-infrared spectroscopy (NIRS) non-invasively monitors muscle tissue oxygen saturation (StO2). It may provide a continuous noninvasive measurement to identify occult hypoperfusion, guide resuscitation, and predict the development of multiple organ dysfunction (MOD) after severe trauma. We evaluated the correlation between initial StO2 and the development of MOD in multi-trauma patients. Patients presenting to our urban, academic, Level I Trauma Center/Emergency Department and meeting standardized trauma-team activation criteria were enrolled in this prospective trial. NIRS monitoring was initiated immediately on arrival with collection of StO2 at the thenar eminence and continued up to 24 hours for those admitted to the Trauma Intensive Care Unit (TICU). Standardized resuscitation laboratory measures and clinical evaluation tools were collected. The primary outcome was the association between initial StO2 and the development of MOD within the first 24 hours based on a MOD score of 6 or greater. Descriptive statistical analyses were performed; numeric means, multivariate regression and rank sum comparisons were utilized. Clinicians were blinded from the StO2 values. Over a 14 month period, 78 patients were enrolled. Mean age was 40.9 years (SD 18.2), 84.4% were male, 76.9% had a blunt trauma mechanism and mean injury severity score (ISS) was 18.5 (SD 12.9). Of the 78 patients, 26 (33.3%) developed MOD within the first 24 hours. The MOD patients had mean initial StO2 values of 53.3 (SD 10.3), significantly lower than those of non-MOD patients 61.1 (SD 10.0); P=0.002. The mean ISS among MOD patients was 29.9 (SD 11.5), significantly higher than that of non-MODS patients, 12.1 (SD 9.1) (P<0.0001). The mean shock index (SI) among MOD patients was 0.92 (SD 0.28), also significantly higher than that of non-MODS patients, 0.73 (SD 0.19) (P=0.0007). Lactate values were not significantly different between groups. Non-invasive, continuous StO2 near-infrared spectroscopy values during initial trauma resuscitation correlate with the later development of multiple organ dysfunction in this patient population.

Hamilton-Jacobi theory in multisymplectic classical field theories

NASA Astrophysics Data System (ADS)

de León, Manuel; Prieto-Martínez, Pedro Daniel; Román-Roy, Narciso; Vilariño, Silvia

2017-09-01

The geometric framework for the Hamilton-Jacobi theory developed in the studies of Cariñena et al. [Int. J. Geom. Methods Mod. Phys. 3(7), 1417-1458 (2006)], Cariñena et al. [Int. J. Geom. Methods Mod. Phys. 13(2), 1650017 (2015)], and de León et al. [Variations, Geometry and Physics (Nova Science Publishers, New York, 2009)] is extended for multisymplectic first-order classical field theories. The Hamilton-Jacobi problem is stated for the Lagrangian and the Hamiltonian formalisms of these theories as a particular case of a more general problem, and the classical Hamilton-Jacobi equation for field theories is recovered from this geometrical setting. Particular and complete solutions to these problems are defined and characterized in several equivalent ways in both formalisms, and the equivalence between them is proved. The use of distributions in jet bundles that represent the solutions to the field equations is the fundamental tool in this formulation. Some examples are analyzed and, in particular, the Hamilton-Jacobi equation for non-autonomous mechanical systems is obtained as a special case of our results.

GADEP Continuous PM2.5 mass concentration data, VIIRS Day Night Band SDR (SVDNB), MODIS Terra Level 2 water vapor profiles (infrared algorithm for atmospheric profiles for both day and night, NWS surface meteorological data

EPA Pesticide Factsheets

Data descriptions are provided at the following urls:GADEP Continuous PM2.5 mass concentration data - https://aqs.epa.gov/aqsweb/documents/data_mart_welcome.htmlhttps://www3.epa.gov/ttn/amtic/files/ambient/pm25/qa/QA-Handbook-Vol-II.pdfVIIRS Day Night Band SDR (SVDNB) http://www.class.ngdc.noaa.gov/saa/products/search?datatype_family=VIIRS_SDRMODIS Terra Level 2 water vapor profiles (infrared algorithm for atmospheric profiles for both day and night -MOD0&_L2; http://modis-atmos.gsfc.nasa.gov/MOD07_L2/index.html NWS surface meteorological data - https://www.ncdc.noaa.gov/isdThis dataset is associated with the following publication:Wang, J., C. Aegerter, and J. Szykman. Potential Application of VIIRS Day/Night Band for Monitoring Nighttime Surface PM2.5 Air Quality From Space. ATMOSPHERIC ENVIRONMENT. Elsevier Science Ltd, New York, NY, USA, 124(0): 55-63, (2016).

Signatures of inflammation and impending multiple organ dysfunction in the hyperacute phase of trauma: A prospective cohort study

PubMed Central

Longhi, M. Paula; Hoti, Mimoza; Patel, Minal B.; O’Dwyer, Michael; Nourshargh, Sussan; Barnes, Michael R.; Brohi, Karim

2017-01-01

Background Severe trauma induces a widespread response of the immune system. This “genomic storm” can lead to poor outcomes, including Multiple Organ Dysfunction Syndrome (MODS). MODS carries a high mortality and morbidity rate and adversely affects long-term health outcomes. Contemporary management of MODS is entirely supportive, and no specific therapeutics have been shown to be effective in reducing incidence or severity. The pathogenesis of MODS remains unclear, and several models are proposed, such as excessive inflammation, a second-hit insult, or an imbalance between pro- and anti-inflammatory pathways. We postulated that the hyperacute window after trauma may hold the key to understanding how the genomic storm is initiated and may lead to a new understanding of the pathogenesis of MODS. Methods and findings We performed whole blood transcriptome and flow cytometry analyses on a total of 70 critically injured patients (Injury Severity Score [ISS] ≥ 25) at The Royal London Hospital in the hyperacute time period within 2 hours of injury. We compared transcriptome findings in 36 critically injured patients with those of 6 patients with minor injuries (ISS ≤ 4). We then performed flow cytometry analyses in 34 critically injured patients and compared findings with those of 9 healthy volunteers. Immediately after injury, only 1,239 gene transcripts (4%) were differentially expressed in critically injured patients. By 24 hours after injury, 6,294 transcripts (21%) were differentially expressed compared to the hyperacute window. Only 202 (16%) genes differentially expressed in the hyperacute window were still expressed in the same direction at 24 hours postinjury. Pathway analysis showed principally up-regulation of pattern recognition and innate inflammatory pathways, with down-regulation of adaptive responses. Immune deconvolution, flow cytometry, and modular analysis suggested a central role for neutrophils and Natural Killer (NK) cells, with underexpression of T- and B cell responses. In the transcriptome cohort, 20 critically injured patients later developed MODS. Compared with the 16 patients who did not develop MODS (NoMODS), maximal differential expression was seen within the hyperacute window. In MODS versus NoMODS, 363 genes were differentially expressed on admission, compared to only 33 at 24 hours postinjury. MODS transcripts differentially expressed in the hyperacute window showed enrichment among diseases and biological functions associated with cell survival and organismal death rather than inflammatory pathways. There was differential up-regulation of NK cell signalling pathways and markers in patients who would later develop MODS, with down-regulation of neutrophil deconvolution markers. This study is limited by its sample size, precluding more detailed analyses of drivers of the hyperacute response and different MODS phenotypes, and requires validation in other critically injured cohorts. Conclusions In this study, we showed how the hyperacute postinjury time window contained a focused, specific signature of the response to critical injury that led to widespread genomic activation. A transcriptomic signature for later development of MODS was present in this hyperacute window; it showed a strong signal for cell death and survival pathways and implicated NK cells and neutrophil populations in this differential response. PMID:28715416

Eye Movements and Visual Search: A Bibliography,

DTIC Science & Technology

1983-01-01

Stacey, S.R.; Snyder, H.L. Air-to-air target acquisition: Factors and means of improvement. School of Aerospace Medicine , Brooks AFB, TX, Final Report no...Annual Conference on en6ineerin6 in medicine and biology, Washington , 16-19 November, 1970, p. 136. New York: IEEZ, 1970. EYM, MOD, PSY, CTL 222...HDM, ABN, EYM 242 Freska, C., Ellis, S., Stark, L. Simplified measurement of eye fixation. Computers in Biology and Medicine , 1980. INlS, FIX 243

Performance of Linear and Nonlinear Two-Leaf Light Use Efficiency Models at Different Temporal Scales

DOE PAGES

Wu, Xiaocui; Ju, Weimin; Zhou, Yanlian; ...

2015-02-25

The reliable simulation of gross primary productivity (GPP) at various spatial and temporal scales is of significance to quantifying the net exchange of carbon between terrestrial ecosystems and the atmosphere. This study aimed to verify the ability of a nonlinear two-leaf model (TL-LUEn), a linear two-leaf model (TL-LUE), and a big-leaf light use efficiency model (MOD17) to simulate GPP at half-hourly, daily and 8-day scales using GPP derived from 58 eddy-covariance flux sites in Asia, Europe and North America as benchmarks. Model evaluation showed that the overall performance of TL-LUEn was slightly but not significantly better than TL-LUE at half-hourlymore » and daily scale, while the overall performance of both TL-LUEn and TL-LUE were significantly better (p < 0.0001) than MOD17 at the two temporal scales. The improvement of TL-LUEn over TL-LUE was relatively small in comparison with the improvement of TL-LUE over MOD17. However, the differences between TL-LUEn and MOD17, and TL-LUE and MOD17 became less distinct at the 8-day scale. As for different vegetation types, TL-LUEn and TL-LUE performed better than MOD17 for all vegetation types except crops at the half-hourly scale. At the daily and 8-day scales, both TL-LUEn and TL-LUE outperformed MOD17 for forests. However, TL-LUEn had a mixed performance for the three non-forest types while TL-LUE outperformed MOD17 slightly for all these non-forest types at daily and 8-day scales. The better performance of TL-LUEn and TL-LUE for forests was mainly achieved by the correction of the underestimation/overestimation of GPP simulated by MOD17 under low/high solar radiation and sky clearness conditions. TL-LUEn is more applicable at individual sites at the half-hourly scale while TL-LUE could be regionally used at half-hourly, daily and 8-day scales. MOD17 is also an applicable option regionally at the 8-day scale.« less

Performance of Linear and Nonlinear Two-Leaf Light Use Efficiency Models at Different Temporal Scales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Xiaocui; Ju, Weimin; Zhou, Yanlian

The reliable simulation of gross primary productivity (GPP) at various spatial and temporal scales is of significance to quantifying the net exchange of carbon between terrestrial ecosystems and the atmosphere. This study aimed to verify the ability of a nonlinear two-leaf model (TL-LUEn), a linear two-leaf model (TL-LUE), and a big-leaf light use efficiency model (MOD17) to simulate GPP at half-hourly, daily and 8-day scales using GPP derived from 58 eddy-covariance flux sites in Asia, Europe and North America as benchmarks. Model evaluation showed that the overall performance of TL-LUEn was slightly but not significantly better than TL-LUE at half-hourlymore » and daily scale, while the overall performance of both TL-LUEn and TL-LUE were significantly better (p < 0.0001) than MOD17 at the two temporal scales. The improvement of TL-LUEn over TL-LUE was relatively small in comparison with the improvement of TL-LUE over MOD17. However, the differences between TL-LUEn and MOD17, and TL-LUE and MOD17 became less distinct at the 8-day scale. As for different vegetation types, TL-LUEn and TL-LUE performed better than MOD17 for all vegetation types except crops at the half-hourly scale. At the daily and 8-day scales, both TL-LUEn and TL-LUE outperformed MOD17 for forests. However, TL-LUEn had a mixed performance for the three non-forest types while TL-LUE outperformed MOD17 slightly for all these non-forest types at daily and 8-day scales. The better performance of TL-LUEn and TL-LUE for forests was mainly achieved by the correction of the underestimation/overestimation of GPP simulated by MOD17 under low/high solar radiation and sky clearness conditions. TL-LUEn is more applicable at individual sites at the half-hourly scale while TL-LUE could be regionally used at half-hourly, daily and 8-day scales. MOD17 is also an applicable option regionally at the 8-day scale.« less

Markers of data quality in computer audit: the Manchester Orthopaedic Database.

PubMed

Ricketts, D; Newey, M; Patterson, M; Hitchin, D; Fowler, S

1993-11-01

This study investigates the efficiency of the Manchester Orthopaedic Database (MOD), a computer software package for record collection and audit. Data is entered into the system in the form of diagnostic, operative and complication keywords. We have calculated the completeness, accuracy and quality (completeness x accuracy) of keyword data in the MOD in two departments of orthopaedics (Departments A and B). In each department, 100 sets of inpatient notes were reviewed. Department B obtained results which were significantly better than those in A at the 5% level. We attribute this to the presence of a systems coordinator to motivate and organise the team for audit. Senior and junior staff did not differ significantly with respect to completeness, accuracy and quality measures, but locum junior staff recorded data with a quality of 0%. Statistically, the biggest difference between the departments was the quality of operation keywords. Sample sizes were too small to permit effective statistical comparisons between the quality of complication keywords. In both departments, however, the poorest quality data was seen in complication keywords. The low complication keyword completeness contributed to this; on average, the true complication rate (39%) was twice the recorded complication rate (17%). In the recent Royal College of Surgeons of England Confidential Comparative Audit, the recorded complication rate was 4.7%. In the light of the above findings, we suggest that the true complication rate of the RCS CCA should approach 9%.

Integrated, Reactor Relevant Solutions for Lower Hybrid Range of Frequencies Actuators

NASA Astrophysics Data System (ADS)

Shiraiwa, S.; Bonoli, P. T.; Lin, Y.; Wallace, G. M.; Wukitch, S. J.

2017-10-01

RF (radiofrequency) actuators with high system efficiency (wall-plug to plasma) and ability for continuous operation have long be recognized as essential tools for realizing a steady state tokamak. A number of physics and technological challenges to utilization remain including current drive efficiency and location, efficient coupling, and impurity contamination. In a reactor environment, plasma material interaction (PMI) issues associated with coupling structures are similar to the first wall and have been identified as a potential show-stopper. High field side (HFS) launch of LHRF power represents an integrated solution that both improves core wave physics and mitigates PMI/coupling issues. For HFS LHRF, wave penetration is vastly improves because wave accessibility scales as 1/B allowing for launching the wave at lower n|| (parallel refractive index). The lower n|| penetrate to higher electron temperature resulting in higher current drive efficiency (1/n||2). HFS RF launch also provides for a means to dramatically improve launcher robustness in a reactor environment. On the HFS, the SOL is quiescent; local density profile is steep and controlled through magnetic shape; fast particle, neutron, turbulent heat and particle fluxes are eliminated or minim Work supported by the U.S. DoE, Office of Science, Office of Fusion Energy Sciences, User Facility Alcator C-Mod under DE-FC02-99ER54512 and US DoE Contract No. DE-FC02-01ER54648 under a Scientific Discovery through Advanced Computing Initiative.

Efficacy of Genetically Modified Bt Toxins Alone and in Combinations Against Pink Bollworm Resistant to Cry1Ac and Cry2Ab

PubMed Central

Tabashnik, Bruce E.; Fabrick, Jeffrey A.; Unnithan, Gopalan C.; Yelich, Alex J.; Masson, Luke; Zhang, Jie; Bravo, Alejandra; Soberón, Mario

2013-01-01

Evolution of resistance in pests threatens the long-term efficacy of insecticidal proteins from Bacillus thuringiensis (Bt) used in sprays and transgenic crops. Previous work showed that genetically modified Bt toxins Cry1AbMod and Cry1AcMod effectively countered resistance to native Bt toxins Cry1Ab and Cry1Ac in some pests, including pink bollworm (Pectinophora gossypiella). Here we report that Cry1AbMod and Cry1AcMod were also effective against a laboratory-selected strain of pink bollworm resistant to Cry2Ab as well as to Cry1Ab and Cry1Ac. Resistance ratios based on the concentration of toxin killing 50% of larvae for the resistant strain relative to a susceptible strain were 210 for Cry2Ab, 270 for Cry1Ab, and 310 for Cry1Ac, but only 1.6 for Cry1AbMod and 2.1 for Cry1AcMod. To evaluate the interactions among toxins, we tested combinations of Cry1AbMod, Cry1Ac, and Cry2Ab. For both the resistant and susceptible strains, the net results across all concentrations tested showed slight but significant synergism between Cry1AbMod and Cry2Ab, whereas the other combinations of toxins did not show consistent synergism or antagonism. The results suggest that the modified toxins might be useful for controlling populations of pink bollworm resistant to Cry1Ac, Cry2Ab, or both. PMID:24244692

Mod-2 wind turbine system concept and preliminary design report. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1979-01-01

The configuration development of the MOD-2 wind turbine system is presented. The MOD-2 is design optimized for commercial production rates which, in multi-unit installations, will be integrated into a utility power grid and achieve a cost of electricity at less than 4 cents per kilowatt hour.

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Antonelli, M. (Editor)

1982-01-01

Activities performed on Mod I engine testing and test results; the manufacture, assembly, and test of a Mod I engine in the United States; design initiation of the Mod I-A engine system; transient performance testing; Stirling reference engine manufacturing and reduced size studies; components and subsystems; and the study and test of low cost alloys are summarized.

The Imaging Modulography Technique Revisited for High-Definition Intravascular Ultrasound: Theoretical Framework.

PubMed

Tacheau, Antoine; Le Floc'h, Simon; Finet, Gérard; Doyley, Marvin M; Pettigrew, Roderic I; Cloutier, Guy; Ohayon, Jacques

2016-03-01

Mechanical characterization of atherosclerotic lesions remains an essential step for the detection of vulnerable plaques (VPs). Recently, an intravascular ultrasound (IVUS) elasticity reconstruction method (iMOD) has been tested in vivo by our group. The major limitation of iMOD is the need to estimate the strain field in the entire VP despite attenuated depth penetration signals when using high-definition (HD) IVUS systems. Therefore, an extended iMOD approach (E-iMOD) was designed and applied to coronary lesions of patients imaged in vivo with IVUS. The E-iMOD method (i) quantified necrotic core areas with a mean absolute relative error of 3.5 ± 3.5% and (ii) identified Young's moduli of the necrotic cores and fibrous regions with mean values of 5.7 ± 0.8 kPa and 794.5 ± 22.0 kPa instead of 5 kPa and 800 kPa, respectively. This study demonstrates the potential of the improved HD-IVUS modulography technique E-iMOD to characterize coronary VPs. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. All rights reserved.

Rapid, Efficient Detection and Drug Susceptibility Testing of Mycobacterium tuberculosis in Sputum by Microscopic Observation of Broth Cultures

PubMed Central

Caviedes, Luz; Lee, Tien-Shun; Gilman, Robert H.; Sheen, Patricia; Spellman, Emily; Lee, Ellen H.; Berg, Douglas E.; Montenegro-James, Sonia

2000-01-01

Inexpensive, rapid, and reliable methods of detecting infection by and drug susceptibility of Mycobacterium tuberculosis (MTB) are crucial to the control of tuberculosis. The novel microscopic observation broth-drug susceptibility assay (MODS) detects early growth of MTB in liquid medium, allowing more timely diagnosis and drug susceptibility testing. Sputum samples from hospitalized patients in Peru were analyzed by using stains, culture, and PCR. Sensitivity of MODS (92%) compared favorably with the most sensitive of the other culture methods (93%). Sputum samples positive for tuberculosis were tested for susceptibility to isoniazid and rifampin with the microwell alamar blue assay (MABA) and MODS. In 89% of cases, there was concordance between MODS and MABA. Of the diagnostic and susceptibility testing methods used, MODS yielded results most rapidly (median, 9.0 and 9.5 days, respectively). MODS is a rapid, inexpensive, sensitive, and specific method for MTB detection and susceptibility testing; it is particularly appropriate for use in developing countries burdened by significant infection rates and increasing numbers of multiple-drug-resistant cases. PMID:10699023

Rapid, efficient detection and drug susceptibility testing of Mycobacterium tuberculosis in sputum by microscopic observation of broth cultures. The Tuberculosis Working Group in Peru.

PubMed

Caviedes, L; Lee, T S; Gilman, R H; Sheen, P; Spellman, E; Lee, E H; Berg, D E; Montenegro-James, S

2000-03-01

Inexpensive, rapid, and reliable methods of detecting infection by and drug susceptibility of Mycobacterium tuberculosis (MTB) are crucial to the control of tuberculosis. The novel microscopic observation broth-drug susceptibility assay (MODS) detects early growth of MTB in liquid medium, allowing more timely diagnosis and drug susceptibility testing. Sputum samples from hospitalized patients in Peru were analyzed by using stains, culture, and PCR. Sensitivity of MODS (92%) compared favorably with the most sensitive of the other culture methods (93%). Sputum samples positive for tuberculosis were tested for susceptibility to isoniazid and rifampin with the microwell alamar blue assay (MABA) and MODS. In 89% of cases, there was concordance between MODS and MABA. Of the diagnostic and susceptibility testing methods used, MODS yielded results most rapidly (median, 9.0 and 9.5 days, respectively). MODS is a rapid, inexpensive, sensitive, and specific method for MTB detection and susceptibility testing; it is particularly appropriate for use in developing countries burdened by significant infection rates and increasing numbers of multiple-drug-resistant cases.

Une modélisation de haut niveau des stratégies d'écriture motrice d'enfants en scolarité primaire : approche bayésienne

NASA Astrophysics Data System (ADS)

Zaarour, I.; El-Eter, B.; Leray, P.; Heutte, L.; Labiche, J.; Mellier, D.; Zoaeter, M.

2005-05-01

L'objectif de cette étude est de découvrir des stratégies d'écriture motrices des enfants en scolarité primaire en adoptant un modèle graphique probabiliste (réseaux bayésiens). Nous représentons une stratégie d'écriture par une variable cachée et nous construisons ainsi un modèle global hiérarchique pour pouvoir lier les stratégies locales aux stratégies globales et modéliser la dépendance probabiliste entre variables et stratégies. Ce modèle hiérarchique, appris à partir des données réelles, nous a permis de découvrir des stratégies consistantes et robustes. Ces résultats nous a permis de favoriser une modélisation temporelle et dynamique des stratégies d'écriture motrices indépendantes de l'âge scolaire.

The feasibility of determining the effectiveness and cost-effectiveness of medication organisation devices compared with usual care for older people in a community setting: systematic review, stakeholder focus groups and feasibility randomised controlled trial.

PubMed

Bhattacharya, Debi; Aldus, Clare F; Barton, Garry; Bond, Christine M; Boonyaprapa, Sathon; Charles, Ian S; Fleetcroft, Robert; Holland, Richard; Jerosch-Herold, Christina; Salter, Charlotte; Shepstone, Lee; Walton, Christine; Watson, Steve; Wright, David J

2016-07-01

Medication organisation devices (MODs) provide compartments for a patient's medication to be organised into the days of the week and the recommended times the medication should be taken. To define the optimal trial design for testing the clinical effectiveness and cost-effectiveness of MODs. The feasibility study comprised a systematic review and focus groups to inform a randomised controlled trial (RCT) design. The resulting features were tested on a small scale, using a 2 × 2 factorial design to compare MODs with usual packaging and to compare weekly with monthly supply. The study design was then evaluated. Potential participants were identified by medical practices. Aged over 75 years, prescribed at least three solid oral dosage form medications, unintentionally non-adherent and self-medicating. Participants were excluded if deemed by their health-care team to be unsuitable. One of three MODs widely used in routine clinical practice supplied either weekly or monthly. To identify the most effective method of participant recruitment, to estimate the prevalence of intentional and unintentional non-adherence in an older population, to provide a point estimate of the effect size of MODs relative to usual care and to determine the feasibility and acceptability of trial participation. The systematic review included MOD studies of any design reporting medication adherence, health and social outcomes, resource utilisation or dispensing or administration errors. Focus groups with patients, carers and health-care professionals supplemented the systematic review to inform the RCT design. The resulting design was implemented and then evaluated through questionnaires and group discussions with participants and health-care professionals involved in trial delivery. Studies on MODs are largely of poor quality. The relationship between adherence and health outcomes is unclear. Of the limited studies reporting health outcomes, some reported a positive relationship while some reported increased hospitalisations associated with MODs. The pre-trial focus groups endorsed the planned study design, but suggested a minimum recruitment age of 50-60 years. A total of 35.4% of patients completing the baseline questionnaire were excluded because they already used a MOD. Active recruitment yielded a higher consent rate, but passive recruitment was more cost-effective. The prevalence of intentional non-adherence was 24.7% [n = 71, 95% confidence interval (CI) 19.7% to 29.6%] of participants. Of the remaining 76 participants, 46.1% (95% CI 34.8% to 57.3%) were unintentionally non-adherent. There was no indication of a difference in adherence between the study arms. Participants reported a high level of satisfaction with the design. Five adverse/serious adverse events were identified in the MOD study arms and none was identified in the control arms. There was no discernible difference in health economic outcomes between the four study arms; the mean intervention cost was £20 per month greater for MOD monthly relative to usual supply monthly. MOD provision to unintentionally non-adherent older people may cause medication-related adverse events. The primary outcome for a definitive MOD trial should be health outcomes. Such a trial should recruit patients by postal invitation and recruit younger patients. A study examining the association between MOD initiation and adverse effects is necessary and a strategy to safely introduce MODs should be explored. A definitive study testing the clinical effectiveness and cost-effectiveness of MODs is also required. Current Controlled Trials ISRCTN 30626972 and UKCRN 12739. This project was funded by National Institute for Health Research (NIHR) Health Technology Assessment Programme and will be published in full in Health Technology Assessment; Vol. 20, No. 50. See the NIHR Journals Library website for further project information.

LHC, le Big Bang en éprouvette

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Notre compréhension de l’Univers est en train de changer… Bar des Sciences - Tout public Débat modéré par Marie-Odile Montchicourt, journaliste de France Info. Evenement en vidéoconférence entre le Globe de la science et de l’innovation, le bar le Baloard de Montpellier et la Maison des Métallos à Paris. Intervenants au CERN : Philippe Charpentier et Daniel Froideveaux, physiciens au CERN. Intervenants à Paris : Vincent Bontemps, philosophe et chercheur au CEA ; Jacques Arnould, philosophe, historien des sciences et théologien, Jean-Jacques Beineix, réalisateur, producteur, scénariste de cinéma. Intervenants à Montpellier (LPTA) : André Neveu, physicien théoricien et directeur demore » recherche au CNRS ; Gilbert Moultaka, physicien théoricien et chargé de recherche au CNRS. Partenariat : CERN, CEA, IN2P3, Université MPL2 (LPTA) Dans le cadre de la Fête de la science 2008.« less

Mod-2 wind turbine project assessment and cluster test plans

NASA Technical Reports Server (NTRS)

Gordon, L. H.

1982-01-01

An assessment of the Mod-2 Wind Turbine project is presented based on initial goals and present results. Specifically, the Mod-2 background, project flow, and a chronology of events/results leading to Mod-2 acceptance is presented. After checkout/acceptance of the three operating turbines, NASA/LeRC will continue management of a two year test program performed at the DOE Goodnoe Hills test site. This test program is expected to yield data necessary for the continued development and optimization of wind energy systems. These test activities, the implementation of, and the results to date are also presented.

MOD-2 wind turbine development

NASA Technical Reports Server (NTRS)

Gordon, L. H.; Andrews, J. S.; Zimmerman, D. K.

1983-01-01

The development of the Mod-2 turbine, designed to achieve a cost of electricity for the 100th production unit that will be competitive with conventional electric power generation is discussed. The Mod-2 wind turbine system (WTS) background, project flow, and a chronology of events and problem areas leading to Mod-2 acceptance are addressed. The role of the participating utility during site preparation, turbine erection and testing, remote operation, and routine operation and maintenance activity is reviewed. The technical areas discussed pertain to system performance, loads, and controls. Research and technical development of multimegawatt turbines is summarized.

On HMI's Mod-L Sequence: Test and Evaluation

NASA Astrophysics Data System (ADS)

Liu, Yang; Baldner, Charles; Bogart, R. S.; Bush, R.; Couvidat, S.; Duvall, Thomas L.; Hoeksema, Jon Todd; Norton, Aimee Ann; Scherrer, Philip H.; Schou, Jesper

2016-05-01

HMI Mod-L sequence can produce full Stokes parameters at a cadence of 90 seconds by combining filtergrams from both cameras, the front camera and the side camera. Within the 90-second, the front camera takes two sets of Left and Right Circular Polarizations (LCP and RCP) at 6 wavelengths; the side camera takes one set of Linear Polarizations (I+/-Q and I+/-U) at 6 wavelengths. By combining two cameras, one can obtain full Stokes parameters of [I,Q,U,V] at 6 wavelengths in 90 seconds. In norminal Mod-C sequence that HMI currently uses, the front camera takes LCP and RCP at a cadence of 45 seconds, while the side camera takes observation of the full Stokes at a cadence of 135 seconds. Mod-L should be better than Mod-C for providing vector magnetic field data because (1) Mod-L increases cadence of full Stokes observation, which leads to higher temporal resolution of vector magnetic field measurement; (2) decreases noise in vector magnetic field data because it uses more filtergrams to produce [I,Q,U,V]. There are two potential issues in Mod-L that need to be addressed: (1) scaling intensity of the two cameras’ filtergrams; and (2) if current polarization calibration model, which is built for each camera separately, works for the combined data from both cameras. This presentation will address these questions, and further place a discussion here.

NOX2 protects against progressive lung injury and multiple organ dysfunction syndrome.

PubMed

Whitmore, Laura C; Goss, Kelli L; Newell, Elizabeth A; Hilkin, Brieanna M; Hook, Jessica S; Moreland, Jessica G

2014-07-01

Systemic inflammatory response syndrome (SIRS) is a common clinical condition in patients in intensive care units that can lead to complications, including multiple organ dysfunction syndrome (MODS). MODS carries a high mortality rate, and it is unclear why some patients resolve SIRS, whereas others develop MODS. Although oxidant stress has been implicated in the development of MODS, several recent studies have demonstrated a requirement for NADPH oxidase 2 (NOX2)-derived oxidants in limiting inflammation. We recently demonstrated that NOX2 protects against lung injury and mortality in a murine model of SIRS. In the present study, we investigated the role of NOX2-derived oxidants in the progression from SIRS to MODS. Using a murine model of sterile systemic inflammation, we observed significantly greater illness and subacute mortality in gp91(phox-/y) (NOX2-deficient) mice compared with wild-type mice. Cellular analysis revealed continued neutrophil recruitment to the peritoneum and lungs of the NOX2-deficient mice and altered activation states of both neutrophils and macrophages. Histological examination showed multiple organ pathology indicative of MODS in the NOX2-deficient mice, and several inflammatory cytokines were elevated in lungs of the NOX2-deficient mice. Overall, these data suggest that NOX2 function protects against the development of MODS and is required for normal resolution of systemic inflammation. Copyright © 2014 the American Physiological Society.

The value of microscopic-observation drug susceptibility assay in the diagnosis of tuberculosis and detection of multidrug resistance.

PubMed

Sertel Şelale, Denİz; Uzun, Meltem

2018-01-01

Inexpensive, rapid, and reliable tests for detecting the presence and drug susceptibility of Mycobacterium tuberculosis complex (MTBC) are urgently needed to control the transmission of tuberculosis. In this study, we aimed to assess the accuracy and speed of the microscopic-observation drug susceptibility (MODS) assay in the identification of MTBC and detection of multidrug resistance. Sputum samples from patients suspected to have tuberculosis were simultaneously tested with MODS and conventional culture [Löwenstein-Jensen (LJ) culture, BACTEC MGIT™ 960 (MGIT) system], and drug susceptibility testing (MGIT system) methods. A total of 331 sputum samples were analyzed. Sensitivity and specificity of MODS assay for detection of MTBC strains were 96% and 98.8%, respectively. MODS assay detected multidrug resistant MTBC isolates with 92.3% sensitivity and 96.6% specificity. Median time to culture positivity was similar for MGIT (8 days) and MODS culture (8 days), but was significantly longer with LJ culture (20 days) (p < 0.0001 for both comparisons). Median time to availability of the susceptibility results was significantly (p < 0.0001) shorter with MODS assay (8 days) than MGIT system (20 days). In conclusion, MODS is an inexpensive and rapid test with good performance characteristics for direct diagnosis of tuberculosis and detection of multidrug resistance. © 2017 APMIS. Published by John Wiley & Sons Ltd.

Development of large, horizontal-axis wind turbines

NASA Technical Reports Server (NTRS)

Baldwin, D. H.; Kennard, J.

1985-01-01

A program to develop large, horizontal-axis wind turbines is discussed. The program is directed toward developing the technology for safe, reliable, environmentally acceptable large wind turbines that can generate a significant amount of electricity at costs competitive with those of conventional electricity-generating systems. In addition, these large wind turbines must be fully compatible with electric utility operations and interface requirements. Several ongoing projects in large-wind-turbine development are directed toward meeting the technology requirements for utility applications. The machines based on first-generation technology (Mod-OA and Mod-1) successfully completed their planned periods of experimental operation in June, 1982. The second-generation machines (Mod-2) are in operation at selected utility sites. A third-generation machine (Mod-5) is under contract. Erection and initial operation of the Mod-5 in Hawaii should take place in 1986. Each successive generation of technology increased reliability and energy capture while reducing the cost of electricity. These advances are being made by gaining a better understanding of the system-design drivers, improving the analytical design tools, verifying design methods with operating field data, and incorporating new technology and innovative designs. Information is given on the results from the first- and second-generation machines (Mod-OA, - 1, and -2), the status of the Department of Interior, and the status of the third-generation wind turbine (Mod-5).

Kynurenine–3–monooxygenase inhibition prevents multiple organ failure in rodent models of acute pancreatitis

PubMed Central

Mole, Damian J; Webster, Scott P; Uings, Iain; Zheng, Xiaozhong; Binnie, Margaret; Wilson, Kris; Hutchinson, Jonathan P; Mirguet, Olivier; Walker, Ann; Beaufils, Benjamin; Ancellin, Nicolas; Trottet, Lionel; Bénéton, Véronique; Mowat, Christopher G; Wilkinson, Martin; Rowland, Paul; Haslam, Carl; McBride, Andrew; Homer, Natalie ZM; Baily, James E; Sharp, Matthew GF; Garden, O James; Hughes, Jeremy; Howie, Sarah EM; Holmes, Duncan S; Liddle, John; Iredale, John P

2015-01-01

Acute pancreatitis (AP) is a common and devastating inflammatory condition of the pancreas that is considered to be a paradigm of sterile inflammation leading to systemic multiple organ dysfunction syndrome (MODS) and death1,2 Acute mortality from AP-MODS exceeds 20%3 and for those who survive the initial episode, their lifespan is typically shorter than the general population4. There are no specific therapies available that protect individuals against AP-MODS. Here, we show that kynurenine-3-monooxygenase (KMO), a key enzyme of tryptophan metabolism5, is central to the pathogenesis of AP-MODS. We created a mouse strain deficient for Kmo with a robust biochemical phenotype that protected against extrapancreatic tissue injury to lung, kidney and liver in experimental AP-MODS. A medicinal chemistry strategy based on modifications of the kynurenine substrate led to the discovery of GSK180 as a potent and specific inhibitor of KMO. The binding mode of the inhibitor in the active site was confirmed by X-ray co-crystallography at 3.2 Å resolution. Treatment with GSK180 resulted in rapid changes in levels of kynurenine pathway metabolites in vivo and afforded therapeutic protection against AP-MODS in a rat model of AP. Our findings establish KMO inhibition as a novel therapeutic strategy in the treatment of AP-MODS and open up a new area for drug discovery in critical illness. PMID:26752518

Identification of Bacillus thuringiensis Cry1AbMod binding-proteins from Spodoptera frugiperda.

PubMed

Martínez de Castro, Diana L; García-Gómez, Blanca I; Gómez, Isabel; Bravo, Alejandra; Soberón, Mario

2017-12-01

Bacillus thuringiensis Cry toxins are currently used for pest control in transgenic crops but evolution of resistance by the insect pests threatens the use of this technology. The Cry1AbMod toxin was engineered to lack the alpha helix-1 of the parental Cry1Ab toxin and was shown to counter resistance to Cry1Ab and Cry1Ac toxins in different insect species including the fall armyworm Spodoptera frugiperda. In addition, Cry1AbMod showed enhanced toxicity to Cry1Ab-susceptible S. frugiperda populations. To gain insights into the mechanisms of this Cry1AbMod-enhanced toxicity, we isolated the Cry1AbMod toxin binding proteins from S. frugiperda brush border membrane vesicles (BBMV), which were identified by pull-down assay and liquid chromatography-tandem mass spectrometry (LC-MS/MS). The LC-MS/MS results indicated that Cry1AbMod toxin could bind to four classes of aminopeptidase (N1, N3, N4 y N5) and actin, with the highest amino acid sequence coverage acquired for APN 1 and APN4. In addition to these proteins, we found other proteins not previously described as Cry toxin binding proteins. This is the first report that suggests the interaction between Cry1AbMod and APN in S. frugiperda. Copyright © 2017 Elsevier Inc. All rights reserved.

Potential of VIIRS Time Series Data for Aiding the USDA Forest Service Early Warning System for Forest Health Threats: A Gypsy Moth Defoliation Case Study

NASA Technical Reports Server (NTRS)

Spruce, Joseph P.; Ryan, Robert E.; Smoot, James; Kuper, Phillip; Prados, Donald; Russell, Jeffrey; Ross, Kenton; Gasser, Gerald; Sader, Steven; McKellip, Rodney

2007-01-01

This report details one of three experiments performed during FY 2007 for the NASA RPC (Rapid Prototyping Capability) at Stennis Space Center. This RPC experiment assesses the potential of VIIRS (Visible/Infrared Imager/Radiometer Suite) and MODIS (Moderate Resolution Imaging Spectroradiometer) data for detecting and monitoring forest defoliation from the non-native Eurasian gypsy moth (Lymantria dispar). The intent of the RPC experiment was to assess the degree to which VIIRS data can provide forest disturbance monitoring information as an input to a forest threat EWS (Early Warning System) as compared to the level of information that can be obtained from MODIS data. The USDA Forest Service (USFS) plans to use MODIS products for generating broad-scaled, regional monitoring products as input to an EWS for forest health threat assessment. NASA SSC is helping the USFS to evaluate and integrate currently available satellite remote sensing technologies and data products for the EWS, including the use of MODIS products for regional monitoring of forest disturbance. Gypsy moth defoliation of the mid-Appalachian highland region was selected as a case study. Gypsy moth is one of eight major forest insect threats listed in the Healthy Forest Restoration Act (HFRA) of 2003; the gypsy moth threatens eastern U.S. hardwood forests, which are also a concern highlighted in the HFRA of 2003. This region was selected for the project because extensive gypsy moth defoliation occurred there over multiple years during the MODIS operational period. This RPC experiment is relevant to several nationally important mapping applications, including agricultural efficiency, coastal management, ecological forecasting, disaster management, and carbon management. In this experiment, MODIS data and VIIRS data simulated from MODIS were assessed for their ability to contribute broad, regional geospatial information on gypsy moth defoliation. Landsat and ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) data were used to assess the quality of gypsy moth defoliation mapping products derived from MODIS data and from simulated VIIRS data. The project focused on use of data from MODIS Terra as opposed to MODIS Aqua mainly because only MODIS Terra data was collected during 2000 and 2001-years with comparatively high amounts of gypsy moth defoliation within the study area. The project assessed the quality of VIIRS data simulation products. Hyperion data was employed to assess the quality of MODIS-based VIIRS simulation datasets using image correlation analysis techniques. The ART (Application Research Toolbox) software was used for data simulation. Correlation analysis between MODIS-simulated VIIRS data and Hyperion-simulated VIIRS data for red, NIR (near-infrared), and NDVI (Normalized Difference Vegetation Index) image data products collectively indicate that useful, effective VIIRS simulations can be produced using Hyperion and MODIS data sources. The r(exp 2) for red, NIR, and NDVI products were 0.56, 0.63, and 0.62, respectively, indicating a moderately high correlation between the 2 data sources. Temporal decorrelation from different data acquisition times and image misregistration may have lowered correlation results. The RPC experiment also generated MODIS-based time series data products using the TSPT (Time Series Product Tool) software. Time series of simulated VIIRS NDVI products were produced at approximately 400-meter resolution GSD (Ground Sampling Distance) at nadir for comparison to MODIS NDVI products at either 250- or 500-meter GSD. The project also computed MODIS (MOD02) NDMI (Normalized Difference Moisture Index) products at 500-meter GSD for comparison to NDVI-based products. For each year during 2000-2006, MODIS and VIIRS (simulated from MOD02) time series were computed during the peak gypsy moth defoliation time frame in the study area (approximately June 10 through July 27). Gypsy moth defoliation mapping products from simated VIIRS and MOD02 time series were produced using multiple methods, including image classification and change detection via image differencing. The latter enabled an automated defoliation detection product computed using percent change in maximum NDVI for a peak defoliation period during 2001 compared to maximum NDVI across the entire 2000-2006 time frame. Final gypsy moth defoliation mapping products were assessed for accuracy using randomly sampled locations found on available geospatial reference data (Landsat and ASTER data in conjunction with defoliation map data from the USFS). Extensive gypsy moth defoliation patches were evident on screen displays of multitemporal color composites derived from MODIS data and from simulated VIIRS vegetation index data. Such defoliation was particularly evident for 2001, although widespread denuded forests were also seen for 2000 and 2003. These visualizations were validated using aforementioned reference data. Defoliation patches were visible on displays of MODIS-based NDVI and NDMI data. The viewing of apparent defoliation patches on all of these products necessitated adoption of a specialized temporal data processing method (e.g., maximum NDVI during the peak defoliation time frame). The frequency of cloud cover necessitated this approach. Multitemporal simulated VIIRS and MODIS Terra data both produced effective general classifications of defoliated forest versus other land cover. For 2001, the MOD02-simulated VIIRS 400-meter NDVI classification produced a similar yet slightly lower overall accuracy (87.28 percent with 0.72 Kappa) than the MOD02 250-meter NDVI classification (88.44 percent with 0.75 Kappa). The MOD13 250-meter NDVI classification had a lower overall accuracy (79.13 percent) and a much lower Kappa (0.46). The report discusses accuracy assessment results in much more detail, comparing overall classification and individual class accuracy statistics for simulated VIIRS 400-meter NDVI, MOD02 250-meter NDVI, MOD02-500 meter NDVI, MOD13 250-meter NDVI, and MOD02 500-meter NDMI classifications. Automated defoliation detection products from simulated VIIRS and MOD02 data for 2001 also yielded similar, relatively high overall classification accuracy (85.55 percent for the VIIRS 400-meter NDVI versus 87.28 percent for the MOD02 250-meter NDVI). In contrast, the USFS aerial sketch map of gypsy moth defoliation showed a lower overall classification accuracy at 73.64 percent. The overall classification Kappa values were also similar for the VIIRS (approximately 0.67 Kappa) versus the MOD02 (approximately 0.72 Kappa) automated defoliation detection product, which were much higher than the values exhibited by the USFS sketch map product (overall Kappa of approximately 0.47). The report provides additional details on the accuracy of automated gypsy moth defoliation detection products compared with USFS sketch maps. The results suggest that VIIRS data can be effectively simulated from MODIS data and that VIIRS data will produce gypsy moth defoliation mapping products that are similar to MODIS-based products. The results of the RPC experiment indicate that VIIRS and MODIS data products have good potential for integration into the forest threat EWS. The accuracy assessment was performed only for 2001 because of time constraints and a relative scarcity of cloud-free Landsat and ASTER data for the peak defoliation period of the other years in the 2000-2006 time series. Additional work should be performed to assess the accuracy of gypsy moth defoliation detection products for additional years.The study area (mid-Appalachian highlands) and application (gypsy moth forest defoliation) are not necessarily representative of all forested regions and of all forest threat disturbance agents. Additional work should be performed on other inland and coastal regions as well as for other major forest threats.

Application of a MODIS Soil Moisture-Evapotranspiration (MOD-SMET) Model to Evaluate Landscape and Hydrologic Recovery after the High Park Fire in Colorado, USA

NASA Astrophysics Data System (ADS)

Blount, W. K.; Hogue, T. S.; Franz, K.; Knipper, K. R.

2017-12-01

Accurate estimation of evapotranspiration (ET) is critical for the management of water resources, especially in water-stressed regions. ET accounts for approximately 60% of terrestrial precipitation globally and approaches 100% of annual rainfall in arid ecosystems, where transpiration becomes the dominant term. ET is difficult to measure due to its spatiotemporal variation, which requires adequate data coverage. While new remote sensing-based ET products are available at a 1 km spatial resolution, including the Operational Simplified Surface Energy Balance model (SSEBop) and the MODIS Global Evapotranspiration Project (MOD16), these products are available at monthly and 8-day temporal resolutions, respectively. To better understand the changing dynamics of hydrologic fluxes and the partitioning of water after land cover disturbances and to identify statically significant trends, more frequent observations are necessary. Utilizing the recently developed MODIS Soil Moisture-Evapotranspiration (MOD-SMET) model, daily temporal resolution is achieved. This presentation outlines the methodology of the MOD-SMET model and compares SSEBop, MOD16, and MOD-SMET ET estimates over the High Park Fire burn scar in Colorado, USA. MOD-SMET estimates are used to identify changes in fluxes and partitioning of the water cycle after a wildfire and during recovery in the High Park Fire near Fort Collins, Colorado. Initial results indicate greenness and ET from all three models decrease post-fire, with higher statistical confidence in high burn areas and spatial patterns that closely align with burn severity. MOD-SMET improves the ability to resolve statistically significant changes in ET following wildfires and better understand changes in the post-fire water budget. Utilizing this knowledge, water resource managers can better plan for, and mitigate, the short- and long-term impacts of wildfire on regional water supplies.

Only minor additional metabolic health benefits of high as opposed to moderate dose physical exercise in young, moderately overweight men.

PubMed

Reichkendler, M H; Rosenkilde, M; Auerbach, P L; Agerschou, J; Nielsen, M B; Kjaer, A; Hoejgaard, L; Sjödin, A; Ploug, T; Stallknecht, B

2014-05-01

The dose-response effects of exercise training on insulin sensitivity, metabolic risk, and quality of life were examined. Sixty-one healthy, sedentary (VO₂max: 35 ± 5 ml/kg/min), moderately overweight (BMI: 27.9 ± 1.8), young (age: 29 ± 6 years) men were randomized to sedentary living (sedentary control group; n = 18), moderate (moderate dose training group [MOD]: 300 kcal/day, n = 21), or high (high dose training group [HIGH]: 600 kcal/day, n = 22) dose physical exercise for 11 weeks. The return rate for post-intervention testing was 82-94% across groups. Weekly exercise amounted to 2,004 ± 24 and 3,774 ± 68 kcal, respectively, in MOD and HIGH. Cardiorespiratory fitness increased (P < 0.001) 18 ± 3% in MOD and 17 ± 3% in HIGH, and fat percentage decreased (P < 0.001) similarly in both exercise groups (MOD: 32 ± 1 to 29 ± 1%; HIGH: 30 ± 1 to 27 ± 1%). Peripheral insulin sensitivity increased (P < 0.01) (MOD: 28 ± 7%; HIGH: 36 ± 8%) and the homeostasis model assessment of insulin resistance decreased (P < 0.05) (MOD: -17 ± 7%; HIGH: -18 ± 10%). The number of subjects meeting the criteria of the metabolic syndrome decreased by 78% in MOD (P < 0.01) and by 80% in HIGH (P < 0.05). General health assessed by questionnaire increased similarly in MOD (P < 0.05) and HIGH (P < 0.01). Only minor additional health benefits were found when exercising ∼3,800 as opposed to ∼2,000 kcal/week in young moderately overweight men. This finding may have important public health implications. Copyright © 2012 The Obesity Society.

Early detection of nonneurologic organ failure in patients with severe traumatic brain injury: Multiple organ dysfunction score or sequential organ failure assessment?

PubMed

Ramtinfar, Sara; Chabok, Shahrokh Yousefzadeh; Chari, Aliakbar Jafari; Reihanian, Zoheir; Leili, Ehsan Kazemnezhad; Alizadeh, Arsalan

2016-10-01

The aim of this study is to compare the discriminant function of multiple organ dysfunction score (MODS) and sequential organ failure assessment (SOFA) components in predicting the Intensive Care Unit (ICU) mortality and neurologic outcome. A descriptive-analytic study was conducted at a level I trauma center. Data were collected from patients with severe traumatic brain injury admitted to the neurosurgical ICU. Basic demographic data, SOFA and MOD scores were recorded daily for all patients. Odd's ratios (ORs) were calculated to determine the relationship of each component score to mortality, and area under receiver operating characteristic (AUROC) curve was used to compare the discriminative ability of two tools with respect to ICU mortality. The most common organ failure observed was respiratory detected by SOFA of 26% and MODS of 13%, and the second common was cardiovascular detected by SOFA of 18% and MODS of 13%. No hepatic or renal failure occurred, and coagulation failure reported as 2.5% by SOFA and MODS. Cardiovascular failure defined by both tools had a correlation to ICU mortality and it was more significant for SOFA (OR = 6.9, CI = 3.6-13.3, P < 0.05 for SOFA; OR = 5, CI = 3-8.3, P < 0.05 for MODS; AUROC = 0.82 for SOFA; AUROC = 0.73 for MODS). The relationship of cardiovascular failure to dichotomized neurologic outcome was not significant statistically. ICU mortality was not associated with respiratory or coagulation failure. Cardiovascular failure defined by either tool significantly related to ICU mortality. Compared to MODS, SOFA-defined cardiovascular failure was a stronger predictor of death. ICU mortality was not affected by respiratory or coagulation failures.

Standardissimo. Les limitations théoriques du Modèle Standard. Quelles réponses y apporter?

NASA Astrophysics Data System (ADS)

Renard, F. M.

Nous présentons I 'état du Modèle Standard des interactions fortes, faibles et électromagnétiques. Après une description rapide de ses 3 secteurs, secteur de jauge (radiation), secteur fermionique (matière) et secteur scalaire (génération des masses), nous insistons sur le grand nombre de paramètres libres et sur les choix arbitraires qu'il a fallu faire dans l'élaboration du modèle. Nous faisons ressortir les problèmes techniques non résolus et nous dressons la liste des questions fondamentales restées sans réponses. Nous passons ensuite en revue les idées et méthodes proposées pour répondre à ces questions. Elles utilisent essentiellement 3 voies différentes. La première consiste à requérir plus de symétrie (extension du modèle, symétrie Gauche-Droite, Grandes Unifications, Supersymétrie,...). La seconde contient les diverses alternatives au Modèle Standard impliquant des modifications dans certains secteurs (par exemple le secteur scalaire avec le modèle de la Technicouleur) ou de façon plus violente l'hypothèse d'une sous-structure des leptons, des quarks et des bosons W et Z eux-mêmes. Une dernière voie cherche à justifier les particularités du Modèle Standard et relier ses paramètres libres en se basant sur des principes de cohérence interne du modèle. Les conséquences observables de ces diverses approches sont dans chaque cas mentionnées.

Evaluation of MOSTAS computer code for predicting dynamic loads in two-bladed wind turbines

NASA Technical Reports Server (NTRS)

Kaza, K. R. V.; Janetzke, D. C.; Sullivan, T. L.

1979-01-01

Calculated dynamic blade loads are compared with measured loads over a range of yaw stiffnesses of the DOE/NASA Mod-0 wind turbine to evaluate the performance of two versions of the MOSTAS computer code. The first version uses a time-averaged coefficient approximation in conjunction with a multiblade coordinate transformation for two-bladed rotors to solve the equations of motion by standard eigenanalysis. The results obtained with this approximate analysis do not agree with dynamic blade load amplifications at or close to resonance conditions. The results of the second version, which accounts for periodic coefficients while solving the equations by a time history integration, compare well with the measured data.

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

1986-01-01

The major accomplishments were the completion of the Basic Stirling Engine (BSE) and the Stirling Engine System (SES) designs on schedule, the approval and acceptance of those designs by NASA, and the initiation of manufacture of BSE components. The performance predictions indicate the Mod II engine design will meet or exceed the original program goals of 30% improvement in fuel economy over a conventional Internal Combustion (IC) powered vehicle, while providing acceptable emissions. This was accomplished while simultaneously reducing Mod II engine weight to a level comparable with IC engine power density, and packaging the Mod II in a 1985 Celebrity with no external sheet metal changes. The projected mileage of the Mod II Celebrity for the combined urban and highway CVS cycle is 40.9 mpg which is a 32% improvement over the IC Celebrity. If additional potential improvements are verified and incorporated in the Mod II, the mileage could increase to 42.7 mpg.

Meteoroid/orbital debris impact damage predictions for the Russian space station MIR

NASA Technical Reports Server (NTRS)

Christiansen, E. L.; Hyde, J. L.; Lear, D.

1997-01-01

Components of the Mir space station have been exposed to the meteoroid/orbital debris (M/OD) environment for up to 11 years. During this period, no M/OD impact perforation of the pressure shell of the manned modules were reported. The NASA standard M/OD analysis code BUMPER was used to predict the probability of M/OD impact damage to various components of Mir. The analysis indicates a 1 in 2.2 chance that a M/OD impact would have caused a penetration resulting in a pressure leak of the Mir modules since its launch up to the February 1997. For the next five years, the estimated odds become 1 in 3. On an annual basis, penetration risks are 60 percent higher, on the average, in the next five years due to the larger size of Mir and the growth in the orbital debris population.

Mod-5A wind turbine generator program design report. Volume 3: Final design and system description, book 2

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3MW MOD-5A wind turbine generator is documented. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 3, book 2 describes the performance and characteristics of the MOD-5A wind turbine generator in its final configuration. The subsystem for power generation, control, and instrumentation subsystems is described in detail. The manufacturing and construction plans, and the preparation of a potential site on Oahu, Hawaii, are documented. The quality assurance and safety plan, and analyses of failure modes and effects, and reliability, availability and maintainability are presented.

Sin1, a Mutation Affecting Female Fertility in Arabidopsis, Interacts with Mod1, Its Recessive Modifier

PubMed Central

Lang, J. D.; Ray, S.; Ray, A.

1994-01-01

In Arabidopsis thaliana, a mutation in the SIN1 gene causes aberrant ovule development and female-specific sterility. The effect of the sin1 mutation is polymorphic and pleiotropic in different genetic backgrounds. The polymorphism concerns morphology of the mutant ovules. The pleiotropism involves internodal distance and inflorescence initiation time. The particular ovule phenotype and the length of internodes are dependent on an interaction of sin1 with a second recessive gene, which we term mod1. The recessive mod1 allele in a homozygous sin1 mutant plant reduces internode length and ovule integument size. The mutation sin1, but not mod1, has a demonstrable effect on ovule morphology when acting idependently. In our crosses mod1 was inseparably linked to the well known mutation erecta that is known to cause a reduction in internode and pedicel lengths. PMID:7982564

Calcul numérique accéléré de mesures de performance sur les modèles Markoviens appliqués aux systèmes informatiques et de télécommunications

NASA Astrophysics Data System (ADS)

Ghaddar, A.; Sinno, N.

2005-05-01

La complexité du phénomène de files d'attente dans les systèmes informatiques et télécommunications nécessite leur simulation par des modèles Markoviens pour les mesures de performance, mesure des délais d'attente au niveau des routeurs pour le modèle informatique et l'étude de la gestion des appels téléphoniques pour le modèle des circuits téléphoniques. L'optimisation des méthodes numériques de résolution des équations relatives à ces deux modèles va permettre d' ídentifier les critères de convergence rapide vers les états stationnaires correspondant à ces mesures.

Fast Voronoi Diagrams and Offsets on Triangulated Surfaces

DTIC Science & Technology

2000-01-01

118 (1996), 499-508. 14. Malladi , R ., and J. A. Sethian, An O(N log N) algorithm for shape mod- eling, Proceedings of National Academy of Sciences...rights of reproduction in any form reserved. 194 R . Kimmel and J. A. Sethian the Osher-Sethian level set method [16,20], which grew out of Sethian’s...where .F(x, y) : R 2 -* R + is a function that defines a weight for each point in the domain. The distance map T(x, y) from a given point Po assigns

Investigating Advances in the Acquisition of Secure Systems Based on Open Architecture, Open Source Software, and Software Product Lines

DTIC Science & Technology

2012-01-27

example is found in games converted to serve a purpose other than entertainment , such as the development and use of games for science, technology, and...These play-session histories can then be further modded via video editing or remixing with other media (e.g., adding music ) to better enable cinematic...available OSS (e.g., the Linux Kernel on the Sony PS3 game console2) that game system hackers seek to undo. Finally, games are one of the most commonly

Fracture & Fatigue Characteristics in Titanium Alloys.

DTIC Science & Technology

1982-06-01

7 AD-All7 155 ROCKWELL INTERNATIONAL THOUSAND OAKS CA SCIENCE CENTER FIG 1i/ 6 FRACTURE & FATI6UE CHARACTERISTICS IN TITANIUM ALLOYS.(U) JUN 82 C 6 ...RECIPIENT’S CATALOG NUMBER 2!, !/,/ S 4 . TITLE (mod Subi.le) S. TYPE OF REPORT & PERIOD COVERED Fracture and Fatigue Characteristics in Final Report Titanium ...tempera- ture fracture toughness of Ti-6A)--4V ( 6 - 4 ) and Ti-4.5A,9-5Mo-l.5Cr (CORONA-5) has been studied as a function of elemental partition- ing and

Knowledge representation and user interface concepts to support mixed-initiative diagnosis

NASA Technical Reports Server (NTRS)

Sobelman, Beverly H.; Holtzblatt, Lester J.

1989-01-01

The Remote Maintenance Monitoring System (RMMS) provides automated support for the maintenance and repair of ModComp computer systems used in the Launch Processing System (LPS) at Kennedy Space Center. RMMS supports manual and automated diagnosis of intermittent hardware failures, providing an efficient means for accessing and analyzing the data generated by catastrophic failure recovery procedures. This paper describes the design and functionality of the user interface for interactive analysis of memory dump data, relating it to the underlying declarative representation of memory dumps.

Improving Reliability in a Stochastic Communication Network

DTIC Science & Technology

1990-12-01

and GINO. In addition, the following computers were used: a Sun 386i workstation, a Digital Equipment Corporation (DEC) 11/785 miniframe , and a DEC...operating system. The DEC 11/785 miniframe used in the experiment was running Unix Version 4.3 (Berkley System Domain). Maxflo was run on the DEC 11/785...the file was still called Mod- ifyl.for). 4. The Maxflo program was started on the DEC 11/785 miniframe . 5. At this time the Convert.max file, created

Operating Systems Standards Working Group (OSSWG) Next Generation Computer Resources (NGCR) Program First Annual Report - October 1990

DTIC Science & Technology

1991-04-01

Rich Bergman NOSC Dale Brouhard NOSC Stephen Cecil CRANE Tom Conrad NUSC Linda Elderhorst NATC Karen Gordon IDA Daniel Green NSWC Steve Howell NSWC Phil...dictate. Some mods for SAFENET have been 22 acceptable to joint WG, some not. 23 o Vendors make prototype and these are evaluated for 24 conformance by...Need to make 13 recommendation to NGCR concern what is feasible for I 34 O.S. 15 o Language binding and/or language independent? Make 16

Applications of SMART: A DRDC Atmospheric Radiative Transfer Library Optimized for Wide Band Computations

DTIC Science & Technology

2011-06-28

DRDC accurate refracted path calculation – 2-stream (flux) and DISORT (N-stream) MS calculations – Lambert and sea surface (DRDC analytical model ) BRDF ...display a currently valid OMB control number. 1. REPORT DATE 28 JUN 2011 2. REPORT TYPE 3. DATES COVERED 00-00-2011 to 00-00-2011 4. TITLE AND...radiance – MODTRAN molecular extinctions (CK) • Seamless integration of MOD4v3r1 – MODTRAN and DRDC aerosol models – Falling snow model (DRDC

Quantum State Tomography of a Fiber-Based Source of Polarization-Entangled Photon Pairs

DTIC Science & Technology

2007-12-20

Processing 175−179 (IEEE, Bangalore, 1984). 4. A. K. Ekert, “ Quantum cryptography based on Bell’s theorem ,” Phys. Rev. Lett. 67, 661–663 (1991). 5...NUMBERS Quantum State Tomography of a Fiber- Based Source of MURI Center for Photonic Quantum Information Systems: AROIARDA Program Polarization...Computer Society Press, Los Alamitos, 1996). 7. N. Gisin, G. Ribordy, W. Tittel, and H. Zbinden, “ Quantum cryptography ,” Rev. Mod. Phys. 74, 145

Development and Evaluation of an Airplane Fuel Tank Ullage Composition Model. Volume 2. Experimental Determination of Airplane Fuel Tank Ullage Compositions

DTIC Science & Technology

1987-10-01

Airplane Fuel Tank Ullage Compositions ~C A. J. Roth BOEING MILITARY AIRPLANE COMPANY P. 0. Box 3707 Seattle, Washington 98124-2207 October 1987 FINAL...controlled mission simulations were made using the ModComp computer to control the Simulated Aircraft Fuel Tank Environment ( SAFTEI facility at Wright...of this report. iii PREFACE This is a final report of work conducted under F33615-84-C-2431 and submitted by the Boeing Military Airplane Company

Mod-5A wind turbine generator program design report. Volume 3: Final design and system description, book 1

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. Volume 3, book 1 describes the performance and characteristics of the MOD-5A wind turbine generator in its final configuration. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation is described in detail.

MOD3D: a model for incorporating MODTRAN radiative transfer into 3D simulations

NASA Astrophysics Data System (ADS)

Berk, Alexander; Anderson, Gail P.; Gossage, Brett N.

2001-08-01

MOD3D, a rapid and accurate radiative transport algorithm, is being developed for application to 3D simulations. MOD3D couples to optical property databases generated by the MODTRAN4 Correlated-k (CK) band model algorithm. The Beer's Law dependence of the CK algorithm provides for proper coupling of illumination and line-of-sight paths. Full 3D spatial effects are modeled by scaling and interpolating optical data to local conditions. A C++ version of MOD3D has been integrated into JMASS for calculation of path transmittances, thermal emission and single scatter solar radiation. Results from initial validation efforts are presented.

Standing Up a Narcotic Confirmation Laboratory for the Russian Federation Ministry of Defense Nuclear Personnel Reliability Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

LukyanenkoMD, Victor; Eisele, Gerhard R; Coates, Cameron W

2010-01-01

Through a cooperative effort between the U. S. Department of Energy and the Russian Federation (RF) Ministry of Defense (MOD) a Personnel Reliability Program (PRP) for the nuclear handlers within the RF MOD has been implemented. A key element in the RF MOD PRP is the detection and confirmation of narcotic use in subject military and civilian personnel. This paper describes the process of narcotics screening and testing in the RF MOD and explains the confirmation process once screening has shown a positive result. Issues of laboratory certification, employee certification, employee training, sample chain-of-custody, and equipment needs will be addressed.

Highly Reactive Thiol-Norbornene Photo-Click Hydrogels: Toward Improved Processability.

PubMed

Van Hoorick, Jasper; Gruber, Peter; Markovic, Marica; Rollot, Mélanie; Graulus, Geert-Jan; Vagenende, Maxime; Tromayer, Maximilian; Van Erps, Jürgen; Thienpont, Hugo; Martins, José C; Baudis, Stefan; Ovsianikov, Aleksandr; Dubruel, Peter; Van Vlierberghe, Sandra

2018-06-10

In the present work, gelatin type B is modified with highly reactive norbornene functionalities (Gel-NB) following a one-pot synthesis approach to enable subsequent thiol-ene photo-click crosslinking. The modification strategy displays close control over the amount of introduced functionalities. Additionally, Gel-NB exhibits considerably improved processing capabilities in terms of two-photon polymerization when benchmarked to earlier-reported crosslinkable gelatin derivatives (e.g., gelatin-methacrylamide (Gel-MOD) and gelatin-methacrylamide-aminoethylmethacrylate (Gel-MOD-AEMA)). The improvement is especially apparent in terms of minimally required laser power (20 mW vs ≥60 mW (Gel-MOD) vs ≥40 mW (Gel-MOD-AEMA) at 100 mm s -1 scan speed) and processable concentration range (≥5 w/v% vs ≥10 w/v% (Gel-MOD/Gel-MOD-AEMA)). Furthermore, the proposed functionalization scheme maintains the excellent biocompatibility and cell interactivity of gelatin. Additionally, the norbornene functionalities have potential for straightforward postprocessing "thiol-ene" surface grafting of active molecules. As a consequence, a very promising material toward tissue engineering applications and more specifically, biofabrication, is presented. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

VarMod: modelling the functional effects of non-synonymous variants

PubMed Central

Pappalardo, Morena; Wass, Mark N.

2014-01-01

Unravelling the genotype–phenotype relationship in humans remains a challenging task in genomics studies. Recent advances in sequencing technologies mean there are now thousands of sequenced human genomes, revealing millions of single nucleotide variants (SNVs). For non-synonymous SNVs present in proteins the difficulties of the problem lie in first identifying those nsSNVs that result in a functional change in the protein among the many non-functional variants and in turn linking this functional change to phenotype. Here we present VarMod (Variant Modeller) a method that utilises both protein sequence and structural features to predict nsSNVs that alter protein function. VarMod develops recent observations that functional nsSNVs are enriched at protein–protein interfaces and protein–ligand binding sites and uses these characteristics to make predictions. In benchmarking on a set of nearly 3000 nsSNVs VarMod performance is comparable to an existing state of the art method. The VarMod web server provides extensive resources to investigate the sequence and structural features associated with the predictions including visualisation of protein models and complexes via an interactive JSmol molecular viewer. VarMod is available for use at http://www.wasslab.org/varmod. PMID:24906884

20 years of research on the Alcator C-Mod tokamaka)

NASA Astrophysics Data System (ADS)

Greenwald, M.; Bader, A.; Baek, S.; Bakhtiari, M.; Barnard, H.; Beck, W.; Bergerson, W.; Bespamyatnov, I.; Bonoli, P.; Brower, D.; Brunner, D.; Burke, W.; Candy, J.; Churchill, M.; Cziegler, I.; Diallo, A.; Dominguez, A.; Duval, B.; Edlund, E.; Ennever, P.; Ernst, D.; Faust, I.; Fiore, C.; Fredian, T.; Garcia, O.; Gao, C.; Goetz, J.; Golfinopoulos, T.; Granetz, R.; Grulke, O.; Hartwig, Z.; Horne, S.; Howard, N.; Hubbard, A.; Hughes, J.; Hutchinson, I.; Irby, J.; Izzo, V.; Kessel, C.; LaBombard, B.; Lau, C.; Li, C.; Lin, Y.; Lipschultz, B.; Loarte, A.; Marmar, E.; Mazurenko, A.; McCracken, G.; McDermott, R.; Meneghini, O.; Mikkelsen, D.; Mossessian, D.; Mumgaard, R.; Myra, J.; Nelson-Melby, E.; Ochoukov, R.; Olynyk, G.; Parker, R.; Pitcher, S.; Podpaly, Y.; Porkolab, M.; Reinke, M.; Rice, J.; Rowan, W.; Schmidt, A.; Scott, S.; Shiraiwa, S.; Sierchio, J.; Smick, N.; Snipes, J. A.; Snyder, P.; Sorbom, B.; Stillerman, J.; Sung, C.; Takase, Y.; Tang, V.; Terry, J.; Terry, D.; Theiler, C.; Tronchin-James, A.; Tsujii, N.; Vieira, R.; Walk, J.; Wallace, G.; White, A.; Whyte, D.; Wilson, J.; Wolfe, S.; Wright, G.; Wright, J.; Wukitch, S.; Zweben, S.

2014-11-01

The object of this review is to summarize the achievements of research on the Alcator C-Mod tokamak [Hutchinson et al., Phys. Plasmas 1, 1511 (1994) and Marmar, Fusion Sci. Technol. 51, 261 (2007)] and to place that research in the context of the quest for practical fusion energy. C-Mod is a compact, high-field tokamak, whose unique design and operating parameters have produced a wealth of new and important results since it began operation in 1993, contributing data that extends tests of critical physical models into new parameter ranges and into new regimes. Using only high-power radio frequency (RF) waves for heating and current drive with innovative launching structures, C-Mod operates routinely at reactor level power densities and achieves plasma pressures higher than any other toroidal confinement device. C-Mod spearheaded the development of the vertical-target divertor and has always operated with high-Z metal plasma facing components—approaches subsequently adopted for ITER. C-Mod has made ground-breaking discoveries in divertor physics and plasma-material interactions at reactor-like power and particle fluxes and elucidated the critical role of cross-field transport in divertor operation, edge flows and the tokamak density limit. C-Mod developed the I-mode and the Enhanced Dα H-mode regimes, which have high performance without large edge localized modes and with pedestal transport self-regulated by short-wavelength electromagnetic waves. C-Mod has carried out pioneering studies of intrinsic rotation and demonstrated that self-generated flow shear can be strong enough in some cases to significantly modify transport. C-Mod made the first quantitative link between the pedestal temperature and the H-mode's performance, showing that the observed self-similar temperature profiles were consistent with critical-gradient-length theories and followed up with quantitative tests of nonlinear gyrokinetic models. RF research highlights include direct experimental observation of ion cyclotron range of frequency (ICRF) mode-conversion, ICRF flow drive, demonstration of lower-hybrid current drive at ITER-like densities and fields and, using a set of novel diagnostics, extensive validation of advanced RF codes. Disruption studies on C-Mod provided the first observation of non-axisymmetric halo currents and non-axisymmetric radiation in mitigated disruptions. A summary of important achievements and discoveries are included.

Coupling of TRAC-PF1/MOD2, Version 5.4.25, with NESTLE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knepper, P.L.; Hochreiter, L.E.; Ivanov, K.N.

1999-09-01

A three-dimensional (3-D) spatial kinetics capability within a thermal-hydraulics system code provides a more correct description of the core physics during reactor transients that involve significant variations in the neutron flux distribution. Coupled codes provide the ability to forecast safety margins in a best-estimate manner. The behavior of a reactor core and the feedback to the plant dynamics can be accurately simulated. For each time step, coupled codes are capable of resolving system interaction effects on neutronics feedback and are capable of describing local neutronics effects caused by the thermal hydraulics and neutronics coupling. With the improvements in computational technology,more » modeling complex reactor behaviors with coupled thermal hydraulics and spatial kinetics is feasible. Previously, reactor analysis codes were limited to either a detailed thermal-hydraulics model with simplified kinetics or multidimensional neutron kinetics with a simplified thermal-hydraulics model. The authors discuss the coupling of the Transient Reactor Analysis Code (TRAC)-PF1/MOD2, Version 5.4.25, with the NESTLE code.« less

Aeroelastic stability of wind turbine blade/aileron systems

NASA Technical Reports Server (NTRS)

Strain, J. C.; Mirandy, L.

1995-01-01

Aeroelastic stability analyses have been performed for the MOD-5A blade/aileron system. Various configurations having different aileron torsional stiffness, mass unbalance, and control system damping have been investigated. The analysis was conducted using a code recently developed by the General Electric Company - AILSTAB. The code extracts eigenvalues for a three degree of freedom system, consisting of: (1) a blade flapwise mode; (2) a blade torsional mode; and (3) an aileron torsional mode. Mode shapes are supplied as input and the aileron can be specified over an arbitrary length of the blade span. Quasi-steady aerodynamic strip theory is used to compute aerodynamic derivatives of the wing-aileron combination as a function of spanwise position. Equations of motion are summarized herein. The program provides rotating blade stability boundaries for torsional divergence, classical flutter (bending/torsion) and wing/aileron flutter. It has been checked out against fixed-wing results published by Theodorsen and Garrick. The MOD-5A system is stable with respect to divergence and classical flutter for all practical rotor speeds. Aileron torsional stiffness must exceed a minimum critical value to prevent aileron flutter. The nominal control system stiffness greatly exceeds this minimum during normal operation. The basic system, however, is unstable for the case of a free (or floating) aileron. The instability can be removed either by the addition of torsional damping or mass-balancing the ailerons. The MOD-5A design was performed by the General Electric Company, Advanced Energy Program Department under Contract DEN3-153 with NASA Lewis Research Center and sponsored by the Department of Energy.

Mod5 protein binds to tRNA gene complexes and affects local transcriptional silencing

PubMed Central

Pratt-Hyatt, Matthew; Pai, Dave A.; Haeusler, Rebecca A.; Wozniak, Glenn G.; Good, Paul D.; Miller, Erin L.; McLeod, Ian X.; Yates, John R.; Hopper, Anita K.; Engelke, David R.

2013-01-01

The tRNA gene-mediated (tgm) silencing of RNA polymerase II promoters is dependent on subnuclear clustering of the tRNA genes, but genetic analysis shows that the silencing requires additional mechanisms. We have identified proteins that bind tRNA gene transcription complexes and are required for tgm silencing but not required for gene clustering. One of the proteins, Mod5, is a tRNA modifying enzyme that adds an N6-isopentenyl adenosine modification at position 37 on a small number of tRNAs in the cytoplasm, although a subpopulation of Mod5 is also found in the nucleus. Recent publications have also shown that Mod5 has tumor suppressor characteristics in humans as well as confers drug resistance through prion-like misfolding in yeast. Here, we show that a subpopulation of Mod5 associates with tRNA gene complexes in the nucleolus. This association occurs and is required for tgm silencing regardless of whether the pre-tRNA transcripts are substrates for Mod5 modification. In addition, Mod5 is bound to nuclear pre-tRNA transcripts, although they are not substrates for the A37 modification. Lastly, we show that truncation of the tRNA transcript to remove the normal tRNA structure also alleviates silencing, suggesting that synthesis of intact pre-tRNAs is required for the silencing mechanism. These results are discussed in light of recent results showing that silencing near tRNA genes also requires chromatin modification. PMID:23898186

Kynurenine-3-monooxygenase inhibition prevents multiple organ failure in rodent models of acute pancreatitis.

PubMed

Mole, Damian J; Webster, Scott P; Uings, Iain; Zheng, Xiaozhong; Binnie, Margaret; Wilson, Kris; Hutchinson, Jonathan P; Mirguet, Olivier; Walker, Ann; Beaufils, Benjamin; Ancellin, Nicolas; Trottet, Lionel; Bénéton, Véronique; Mowat, Christopher G; Wilkinson, Martin; Rowland, Paul; Haslam, Carl; McBride, Andrew; Homer, Natalie Z M; Baily, James E; Sharp, Matthew G F; Garden, O James; Hughes, Jeremy; Howie, Sarah E M; Holmes, Duncan S; Liddle, John; Iredale, John P

2016-02-01

Acute pancreatitis (AP) is a common and devastating inflammatory condition of the pancreas that is considered to be a paradigm of sterile inflammation leading to systemic multiple organ dysfunction syndrome (MODS) and death. Acute mortality from AP-MODS exceeds 20% (ref. 3), and the lifespans of those who survive the initial episode are typically shorter than those of the general population. There are no specific therapies available to protect individuals from AP-MODS. Here we show that kynurenine-3-monooxygenase (KMO), a key enzyme of tryptophan metabolism, is central to the pathogenesis of AP-MODS. We created a mouse strain that is deficient for Kmo (encoding KMO) and that has a robust biochemical phenotype that protects against extrapancreatic tissue injury to the lung, kidney and liver in experimental AP-MODS. A medicinal chemistry strategy based on modifications of the kynurenine substrate led to the discovery of the oxazolidinone GSK180 as a potent and specific inhibitor of KMO. The binding mode of the inhibitor in the active site was confirmed by X-ray co-crystallography at 3.2 Å resolution. Treatment with GSK180 resulted in rapid changes in the levels of kynurenine pathway metabolites in vivo, and it afforded therapeutic protection against MODS in a rat model of AP. Our findings establish KMO inhibition as a novel therapeutic strategy in the treatment of AP-MODS, and they open up a new area for drug discovery in critical illness.

Fracture strength of endodontically treated molars transfixed horizontally by a fiber glass post.

PubMed

Beltrão, Maria Cecilia Gomes; Spohr, Ana Maria; Oshima, Hugo Mitsuo Silva; Mota, Eduardo Gonçalves; Burnett, Luiz Henrique

2009-02-01

To assess the effect of a horizontally transfixed fiber glass post placed between buccal and palatal surfaces, on the fracture strength of endodontically treated molar teeth with MOD cavities, either restored with resin-based composite, or not. 75 sound maxillary human third molars were extracted, embedded in acrylic resin blocks and randomly assigned to five groups (n=15). Group A (sound teeth), (control) and Groups B, C, D and E, which were subjected to the following procedures after endodontic treatment: GB--(MOD+Endo), GC--(MOD+Endo+Post), GD--MOD and composite restoration (MOD+Endo+CR), GE--(MOD+Endo+Post+CR). The specimens were stored in distilled water at 37 degrees C for 24 hours. Later, a compressive force was applied by means of a universal testing machine at 1 mm/minute speed, parallel to the long axis of the teeth until fracture occurred. The means of the results (N) followed by the same letter represent no statistical difference by ANOVA and Tukey (P<0.05): GA = 4289.8 (+/- 1128.9)a, GB = 549.6 (+/- 120.7)b, GC = 1474.8 (+/- 338.1)c, GD = 1224.7 (+/- 236.0)c, GE = 2645.4 (+/- 675.1)d. In the analysis of qualitative variables, there was a tendency to cusp fracture in all groups except for Group C. The fiber glass post transfixed horizontally in a MOD cavity significantly increased the fracture resistance of the teeth restored with resin composite.

A snow cover climatology for the Pyrenees from MODIS snow products

NASA Astrophysics Data System (ADS)

Gascoin, S.; Hagolle, O.; Huc, M.; Jarlan, L.; Dejoux, J.-F.; Szczypta, C.; Marti, R.; Sanchez, R.

2015-05-01

The seasonal snow in the Pyrenees is critical for hydropower production, crop irrigation and tourism in France, Spain and Andorra. Complementary to in situ observations, satellite remote sensing is useful to monitor the effect of climate on the snow dynamics. The MODIS daily snow products (Terra/MOD10A1 and Aqua/MYD10A1) are widely used to generate snow cover climatologies, yet it is preferable to assess their accuracies prior to their use. Here, we use both in situ snow observations and remote sensing data to evaluate the MODIS snow products in the Pyrenees. First, we compare the MODIS products to in situ snow depth (SD) and snow water equivalent (SWE) measurements. We estimate the values of the SWE and SD best detection thresholds to 40 mm water equivalent (w.e.) and 150 mm, respectively, for both MOD10A1 and MYD10A1. κ coefficients are within 0.74 and 0.92 depending on the product and the variable for these thresholds. However, we also find a seasonal trend in the optimal SWE and SD thresholds, reflecting the hysteresis in the relationship between the depth of the snowpack (or SWE) and its extent within a MODIS pixel. Then, a set of Landsat images is used to validate MOD10A1 and MYD10A1 for 157 dates between 2002 and 2010. The resulting accuracies are 97% (κ = 0.85) for MOD10A1 and 96% (κ = 0.81) for MYD10A1, which indicates a good agreement between both data sets. The effect of vegetation on the results is analyzed by filtering the forested areas using a land cover map. As expected, the accuracies decrease over the forests but the agreement remains acceptable (MOD10A1: 96%, κ = 0.77; MYD10A1: 95%, κ = 0.67). We conclude that MODIS snow products have a sufficient accuracy for hydroclimate studies at the scale of the Pyrenees range. Using a gap-filling algorithm we generate a consistent snow cover climatology, which allows us to compute the mean monthly snow cover duration per elevation band and aspect classes. There is snow on the ground at least 50% of the time above 1600 m between December and April. We finally analyze the snow patterns for the atypical winter 2011-2012. Snow cover duration anomalies reveal a deficient snowpack on the Spanish side of the Pyrenees, which seems to have caused a drop in the national hydropower production.

An in situ accelerator-based diagnostic for plasma-material interactions science on magnetic fusion devices.

PubMed

Hartwig, Zachary S; Barnard, Harold S; Lanza, Richard C; Sorbom, Brandon N; Stahle, Peter W; Whyte, Dennis G

2013-12-01

This paper presents a novel particle accelerator-based diagnostic that nondestructively measures the evolution of material surface compositions inside magnetic fusion devices. The diagnostic's purpose is to contribute to an integrated understanding of plasma-material interactions in magnetic fusion, which is severely hindered by a dearth of in situ material surface diagnosis. The diagnostic aims to remotely generate isotopic concentration maps on a plasma shot-to-shot timescale that cover a large fraction of the plasma-facing surface inside of a magnetic fusion device without the need for vacuum breaks or physical access to the material surfaces. Our instrument uses a compact (~1 m), high-current (~1 milliamp) radio-frequency quadrupole accelerator to inject 0.9 MeV deuterons into the Alcator C-Mod tokamak at MIT. We control the tokamak magnetic fields--in between plasma shots--to steer the deuterons to material surfaces where the deuterons cause high-Q nuclear reactions with low-Z isotopes ~5 μm into the material. The induced neutrons and gamma rays are measured with scintillation detectors; energy spectra analysis provides quantitative reconstruction of surface compositions. An overview of the diagnostic technique, known as accelerator-based in situ materials surveillance (AIMS), and the first AIMS diagnostic on the Alcator C-Mod tokamak is given. Experimental validation is shown to demonstrate that an optimized deuteron beam is injected into the tokamak, that low-Z isotopes such as deuterium and boron can be quantified on the material surfaces, and that magnetic steering provides access to different measurement locations. The first AIMS analysis, which measures the relative change in deuterium at a single surface location at the end of the Alcator C-Mod FY2012 plasma campaign, is also presented.

Effects of land use and climate change on ecosystem services in Central Asia's arid regions: A case study in Altay Prefecture, China.

PubMed

Fu, Qi; Li, Bo; Hou, Ying; Bi, Xu; Zhang, Xinshi

2017-12-31

The sustainable use of ecosystem services (ES) can contribute to enhancing human well-being. Understanding the effects of land use and climate change on ES can provide scientific and targeted guidance for the sustainable use of ES. The objective of this study was to reveal the way in which land use and climate change influence the spatial and temporal variations of ES in the mountain-oasis-desert system (MODS). In this study, we assessed water yield, soil conservation, crop production, and sand fixation in 1990, 2000, and 2010 in Altay Prefecture, which is representative of the MODS, based on widely used biophysical models. Moreover, we analyzed the effects of different land use and climate change conditions on ES. The results show that the area of forest and bare land decreased in Altay Prefecture. In contrast, the area of grassland with low coverage and cropland increased. The climate of this area presented an overall warming-wetting trend, with warming-drying and cooling-wetting phenomena in some areas. Soil conservation in the mountain zone, water yield in the oasis zone, and sand fixation in the desert zone all decreased under the influence of land use change alone. The warming-drying trend led to decreased water yield in the oasis zone and increased wind erosion in the desert zone. Based on the results, we recommend that local governments achieve sustainable use of ES by planting grasslands with high coverage in the oasis zone, increasing investment in agricultural science and technology, and establishing protected areas in the mountain and desert zones. The methodology in our study can also be applied to other regions with a MODS structure. Copyright © 2017 Elsevier B.V. All rights reserved.

Practical use of a framework for network science experimentation

NASA Astrophysics Data System (ADS)

Toth, Andrew; Bergamaschi, Flavio

2014-06-01

In 2006, the US Army Research Laboratory (ARL) and the UK Ministry of Defence (MoD) established a collaborative research alliance with academia and industry, called the International Technology Alliance (ITA)1 In Network and Information Sciences, to address fundamental issues concerning Network and Information Sciences that will enhance decision making for coalition operations and enable rapid, secure formation of ad hoc teams in coalition environments and enhance US and UK capabilities to conduct coalition warfare. Research conducted under the ITA was extended through collaboration between ARL and IBM UK to characterize and dene a software stack and tooling that has become the reference framework for network science experimentation in support for validation of theoretical research. This paper discusses the composition of the reference framework for experimentation resulting from the ARL/IBM UK collaboration and its use, by the Network Science Collaborative Technology Alliance (NS CTA)2 , in a recent network science experiment conducted at ARL. It also discusses how the experiment was modeled using the reference framework, the integration of two new components, the Apollo Fact-Finder3 tool and the Medusa Crowd Sensing4 application, the limitations identified and how they shall be addressed in future work.

Metallo-organic decomposition films

NASA Technical Reports Server (NTRS)

Gallagher, B. D.

1985-01-01

A summary of metallo-organic deposition (MOD) films for solar cells was presented. The MOD materials are metal ions compounded with organic radicals. The technology is evolving quickly for solar cell metallization. Silver compounds, especially silver neodecanoate, were developed which can be applied by thick-film screening, ink-jet printing, spin-on, spray, or dip methods. Some of the advantages of MOD are: high uniform metal content, lower firing temperatures, decomposition without leaving a carbon deposit or toxic materials, and a film that is stable under ambient conditions. Molecular design criteria were explained along with compounds formulated to date, and the accompanying reactions for these compounds. Phase stability and the other experimental and analytic results of MOD films were presented.

Automotive Stirling engine systems development

NASA Technical Reports Server (NTRS)

Richey, A. E.

1984-01-01

The objective of the Automotive Stirling Engine (ASE) program is to develop a Stirling engine for automotive use that provides a 30 percent improvement in fuel economy relative to a comparable internal-combustion engine while meeting emissions goals. This paper traces the engine systems' development efforts focusing on: (1) a summary of engine system performance for all Mod I engines; (2) the development, program conducted for the upgraded Mod I; and (3) vehicle systems work conducted to enhance vehicle fuel economy. Problems encountered during the upgraded Mod I test program are discussed. The importance of the EPA driving cycle cold-start penalty and the measures taken to minimize that penalty with the Mod II are also addressed.

Characterization of the Hamamatsu 8" R5912-MOD Photomultiplier tube

NASA Astrophysics Data System (ADS)

Kaptanoglu, Tanner

2018-05-01

Current and future neutrino and direct detection dark matter experiments hope to take advantage of improving technologies in photon detection. Many of these detectors are large, monolithic optical detectors that use relatively low-cost, large-area, and efficient photomultiplier tubes (PMTs). A candidate PMT for future experiments is a newly developed prototype Hamamatsu PMT, the R5912-MOD. In this paper we describe measurements made of the single photoelectron time and charge response of the R5912-MOD, as well as detail some direct comparisons to similar PMTs. Most of these measurements were performed on three R5912-MOD PMTs operating at gains close to 1 × 107. The transit time spread (σ) and the charge peak-to-valley were measured to be on average 680ps and 4.2 respectively. The results of this paper show the R5912-MOD is an excellent candidate for future experiments in several regards, particularly due to its narrow spread in timing.

Comparison of three methods for determination of N-nitrosopyrrolidine in fried dry-cured bacon.

PubMed

Gates, R A; Pensabene, J W; Fiddler, W

1984-01-01

The recently developed Eastern Regional Research Center ( ERRC ) dry column chromatographic procedure for determining N-nitrosopyrrolidine (NPYR) in fried cure-pumped bacon was evaluated for its applicability to fried dry-cured bacon. The method was then compared with 2 established procedures for volatile nitrosamine analysis in cured meat products: the multidetection thermal energy analyzer (MD) method and the mineral oil distillation (MOD) screening procedure. No significant difference (P less than 0.05) in NPYR values was found between the ERRC and MD procedures, but significant differences were found between the ERRC and MOD procedures and between the MOD and MD procedures. No artifactual nitrosamine formation was found in the ERRC procedure, but significant amounts were found in samples analyzed by the MOD procedure. The ERRC method was demonstrated to be rugged and very rapid. It is proposed that the ERRC method replace the MOD method as the official screening procedure for NPYR in fried bacon.

Spatially Complete Global Surface Albedos Derived from Terra/MODIS Data

NASA Technical Reports Server (NTRS)

King, Michael D.; Moody, Eric G.; Platnick, Steven; Schaaf, Crystal B.

2004-01-01

Spectral land surface albedo is an important parameter for describing the radiative properties of the Earth. Accordingly it reflects the consequences of natural and human interactions, such as anthropogenic, meteorological, and phenological effects, on global and local climatological trends. Consequently, albedos are integral parts in a variety of research areas, such as general circulation models (GCMs), energy balance studies, modeling of land use and land use change, and biophysical, oceanographic, and meteorological studies. Recent production of land surface anisotropy, diffuse bihemispherical (white-sky) albedo and direct beam directional hemispherical (black-sky) albedo from observations acquired by the MODIS instruments aboard NASA s Terra and Aqua satellite platforms have provided researchers with unprecedented spatial, spectral, and temporal information on the land surface's radiative characteristics. Cloud cover, which cutails retrievals, and the presence of ephemeral and seasonal snow limit the snow-free data to approximately half the global land surfaces on an annual equal-angle basis. This precludes the MOD43B3 albedo products from being used in some remote sensing and ground-based applications, climate models, and global change research projects. An ecosystem-dependent temporal interpolation technique is described that has been developed to fill missing or seasonally snow-covered data in the official MOD43B3 albedo product. The method imposes pixel-level and local regional ecosystem-dependent phenological behavior onto retrieved pixel temporal data in such a way as to maintain pixel-level spatial and spectral detail and integrity. The phenological curves are derived from statistics based on the MODIS MOD12Q1 IGBP land cover classification product geolocated with the MOD43B3 data. The resulting snow-free value-added products provide the scientific community with spatially and temporally complete global white- and black-sky surface albedo maps and statistics. These products are stored on 1'(approximately 10 km) and coarser resolution equal-angle grids, and are computed for the first seven MODIS wavelengths, ranging from 0.47 through 2.1 microns, and for three broadband wavelengths, 0.3-0.7,0.3-5.0 and 0.7-5.0 microns.

Mod-2 wind turbine system cluster research test program. Volume 1: Initial plan E-1290

NASA Technical Reports Server (NTRS)

Gordon, L. H.

1982-01-01

Upon completion of the design and development of three Mod-2 wind turbines, a series of research experiments are planned to gather data on and evaluate the performance, environmental effects, and operation of a cluster as well as a single, large multimegawatt wind turbine. Information on the program objectives, a Mod-2 system description, a planned schedule, organizational roles, and responsibilities, is included.

Mod-5A wind turbine generator program design report. Volume 4: Drawings and specifications, book 5

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. There are four volumes. This volume contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. Detail drawings of several assemblies and subassemblies are given. This is the fifth book of volume 4.

Culture and Creativity: World of Warcraft Modding in China and the US

NASA Astrophysics Data System (ADS)

Kow, Yong Ming; Nardi, Bonnie

Modding - end-user modification of commercial hardware and software - can be traced back at least to 1961 when Spacewar! was developed by a group of MIT students on a DEC PDP-1. Spacewar! evolved into arcade games including Space Wars produced in 1977 by Cinematronics (Sotamaa 2003). In 1992, players altering Wolfenstein 3-D (1992), a first person shooter game made by id Software, overwrote the graphics and sounds by editing the game files. Learning from this experience, id Software released Doom in 1993 with isolated media files and open source code for players to develop custom maps, images, sounds, and other utilities. Players were able to pass on their modifications to others. By 1996, with the release of Quake, end-user modifications had come to be known as "mods," and modding was an accepted part of the gaming community (Kucklich 2005; Postigo 2008a, b). Since late-2005, we have been studying World of Warcraft (WoW) in which the use of mods is an important aspect of player practice (Nardi and Harris 2006; Nardi et al. 2007). Technically minded players with an interest in extending the game write mods and make them available to players for free download on distribution sites. Most modders work for free, but the distribution sites are commercial enterprises with advertising.

VarMod: modelling the functional effects of non-synonymous variants.

PubMed

Pappalardo, Morena; Wass, Mark N

2014-07-01

Unravelling the genotype-phenotype relationship in humans remains a challenging task in genomics studies. Recent advances in sequencing technologies mean there are now thousands of sequenced human genomes, revealing millions of single nucleotide variants (SNVs). For non-synonymous SNVs present in proteins the difficulties of the problem lie in first identifying those nsSNVs that result in a functional change in the protein among the many non-functional variants and in turn linking this functional change to phenotype. Here we present VarMod (Variant Modeller) a method that utilises both protein sequence and structural features to predict nsSNVs that alter protein function. VarMod develops recent observations that functional nsSNVs are enriched at protein-protein interfaces and protein-ligand binding sites and uses these characteristics to make predictions. In benchmarking on a set of nearly 3000 nsSNVs VarMod performance is comparable to an existing state of the art method. The VarMod web server provides extensive resources to investigate the sequence and structural features associated with the predictions including visualisation of protein models and complexes via an interactive JSmol molecular viewer. VarMod is available for use at http://www.wasslab.org/varmod. © The Author(s) 2014. Published by Oxford University Press on behalf of Nucleic Acids Research.

Change in donor profile influenced the percentage of organs transplanted from multiple organ donors.

PubMed

Meers, C; Van Raemdonck, D; Van Gelder, F; Van Hees, D; Desschans, B; De Roey, J; Vanhaecke, J; Pirenne, J

2009-03-01

We hypothesized that the change in donor profile over the years influenced the percentage of transplantations. We reviewed medical records for all multiple-organ donors (MODs) within our network. The percentage of transplanted organs was compared between 1991-1992 (A) and 2006-2007 (B). In period A, 156 potential MODs were identified compared with 278 in period B. Fifteen potential donors (10%) in period A and 114 (41%) in period B were rejected because they were medically not suitable (40% vs 75%) or there was no family consent (60% vs 25%). Of the remaining effective MODs (141 in period A and 164 in period B), mean (standard deviation = SD) age was 34 (5) years vs 49 (17) years (P < .001). Brain death resulted from craniocerebral trauma in 69% vs 39%, cerebrovascular disease in 24% vs 46%, hypoxia in 4% vs 15%, and brain tumor in 2% vs 0.6% (P < .001). Chest trauma was present in 19% vs 9% (P < .01). The percentage of MODs who received mechanical ventilation for more than 5 days was 8% vs 24% (P < .001). The percentage of organs transplanted in periods A vs B was kidneys, 97% vs 79%; livers, 64% vs 85%; hearts, 60% vs 26%; lungs, 7% vs 35%; and pancreas, 6% vs 13% (P < .001). The number of referred potential MODs increased by 80%, resulting in a small increase in effective MOD organs (17%), mainly because of medical contraindications. The MOD profile changed to older age, fewer traumatic brain deaths, and longer ventilation time. We transplanted more livers, lungs, and pancreases but fewer kidneys and hearts.

Precocious Metamorphosis in the Juvenile Hormone–Deficient Mutant of the Silkworm, Bombyx mori

PubMed Central

Daimon, Takaaki; Kozaki, Toshinori; Niwa, Ryusuke; Kobayashi, Isao; Furuta, Kenjiro; Namiki, Toshiki; Uchino, Keiro; Banno, Yutaka; Katsuma, Susumu; Tamura, Toshiki; Mita, Kazuei; Sezutsu, Hideki; Nakayama, Masayoshi; Itoyama, Kyo; Shimada, Toru; Shinoda, Tetsuro

2012-01-01

Insect molting and metamorphosis are intricately governed by two hormones, ecdysteroids and juvenile hormones (JHs). JHs prevent precocious metamorphosis and allow the larva to undergo multiple rounds of molting until it attains the proper size for metamorphosis. In the silkworm, Bombyx mori, several “moltinism” mutations have been identified that exhibit variations in the number of larval molts; however, none of them have been characterized molecularly. Here we report the identification and characterization of the gene responsible for the dimolting (mod) mutant that undergoes precocious metamorphosis with fewer larval–larval molts. We show that the mod mutation results in complete loss of JHs in the larval hemolymph and that the mutant phenotype can be rescued by topical application of a JH analog. We performed positional cloning of mod and found a null mutation in the cytochrome P450 gene CYP15C1 in the mod allele. We also demonstrated that CYP15C1 is specifically expressed in the corpus allatum, an endocrine organ that synthesizes and secretes JHs. Furthermore, a biochemical experiment showed that CYP15C1 epoxidizes farnesoic acid to JH acid in a highly stereospecific manner. Precocious metamorphosis of mod larvae was rescued when the wild-type allele of CYP15C1 was expressed in transgenic mod larvae using the GAL4/UAS system. Our data therefore reveal that CYP15C1 is the gene responsible for the mod mutation and is essential for JH biosynthesis. Remarkably, precocious larval–pupal transition in mod larvae does not occur in the first or second instar, suggesting that authentic epoxidized JHs are not essential in very young larvae of B. mori. Our identification of a JH–deficient mutant in this model insect will lead to a greater understanding of the molecular basis of the hormonal control of development and metamorphosis. PMID:22412378

Metabolic and hormonal responses to isoenergetic high-intensity interval exercise and continuous moderate-intensity exercise.

PubMed

Peake, Jonathan M; Tan, Sok Joo; Markworth, James F; Broadbent, James A; Skinner, Tina L; Cameron-Smith, David

2014-10-01

This study investigated the effects of high-intensity interval training (HIIT) vs. work-matched moderate-intensity continuous exercise (MOD) on metabolism and counterregulatory stress hormones. In a randomized and counterbalanced order, 10 well-trained male cyclists and triathletes completed a HIIT session [81.6 ± 3.7% maximum oxygen consumption (V̇o2 max); 72.0 ± 3.2% peak power output; 792 ± 95 kJ] and a MOD session (66.7 ± 3.5% V̇o2 max; 48.5 ± 3.1% peak power output; 797 ± 95 kJ). Blood samples were collected before, immediately after, and 1 and 2 h postexercise. Carbohydrate oxidation was higher (P = 0.037; 20%), whereas fat oxidation was lower (P = 0.037; -47%) during HIIT vs. MOD. Immediately after exercise, plasma glucose (P = 0.024; 20%) and lactate (P < 0.01; 5.4×) were higher in HIIT vs. MOD, whereas total serum free fatty acid concentration was not significantly different (P = 0.33). Targeted gas chromatography-mass spectromtery metabolomics analysis identified and quantified 49 metabolites in plasma, among which 11 changed after both HIIT and MOD, 13 changed only after HIIT, and 5 changed only after MOD. Notable changes included substantial increases in tricarboxylic acid intermediates and monounsaturated fatty acids after HIIT and marked decreases in amino acids during recovery from both trials. Plasma adrenocorticotrophic hormone (P = 0.019), cortisol (P < 0.01), and growth hormone (P < 0.01) were all higher immediately after HIIT. Plasma norepinephrine (P = 0.11) and interleukin-6 (P = 0.20) immediately after exercise were not significantly different between trials. Plasma insulin decreased during recovery from both HIIT and MOD (P < 0.01). These data indicate distinct differences in specific metabolites and counterregulatory hormones following HIIT vs. MOD and highlight the value of targeted metabolomic analysis to provide more detailed insights into the metabolic demands of exercise. Copyright © 2014 the American Physiological Society.

SnowCloud - a Framework to Predict Streamflow in Snowmelt-dominated Watersheds Using Cloud-based Computing

NASA Astrophysics Data System (ADS)

Sproles, E. A.; Crumley, R. L.; Nolin, A. W.; Mar, E.; Lopez-Moreno, J. J.

2017-12-01

Streamflow in snowy mountain regions is extraordinarily challenging to forecast, and prediction efforts are hampered by the lack of timely snow data—particularly in data sparse regions. SnowCloud is a prototype web-based framework that integrates remote sensing, cloud computing, interactive mapping tools, and a hydrologic model to offer a new paradigm for delivering key data to water resource managers. We tested the skill of SnowCloud to forecast monthly streamflow with one month lead time in three snow-dominated headwaters. These watersheds represent a range of precipitation/runoff schemes: the Río Elqui in northern Chile (200 mm/yr, entirely snowmelt); the John Day River, Oregon, USA (635 mm/yr, primarily snowmelt); and the Río Aragon in the northern Spain (850 mm/yr, snowmelt dominated). Model skill corresponded to snowpack contribution with Nash-Sutcliffe Efficiencies of 0.86, 0.52, and 0.21 respectively. SnowCloud does not require the user to possess advanced programming skills or proprietary software. We access NASA's MOD10A1 snow cover product to calculate the snow metrics globally using Google Earth Engine's geospatial analysis and cloud computing service. The analytics and forecast tools are provided through a web-based portal that requires only internet access and minimal training. To test the efficacy of SnowCloud we provided the tools and a series of tutorials in English and Spanish to water resource managers in Chile, Spain, and the United States. Participants assessed their user experience and provided feedback, and the results of our multi-cultural assessment are also presented. While our results focus on SnowCloud, they outline methods to develop cloud-based tools that function effectively across cultures and languages. Our approach also addresses the primary challenges of science-based computing; human resource limitations, infrastructure costs, and expensive proprietary software. These challenges are particularly problematic in developing countries.

Evaluation of MOSTAS computer code for predicting dynamic loads in two bladed wind turbines

NASA Technical Reports Server (NTRS)

Kaza, K. R. V.; Janetzke, D. C.; Sullivan, T. L.

1979-01-01

Calculated dynamic blade loads were compared with measured loads over a range of yaw stiffnesses of the DOE/NASA Mod-O wind turbine to evaluate the performance of two versions of the MOSTAS computer code. The first version uses a time-averaged coefficient approximation in conjunction with a multi-blade coordinate transformation for two bladed rotors to solve the equations of motion by standard eigenanalysis. The second version accounts for periodic coefficients while solving the equations by a time history integration. A hypothetical three-degree of freedom dynamic model was investigated. The exact equations of motion of this model were solved using the Floquet-Lipunov method. The equations with time-averaged coefficients were solved by standard eigenanalysis.

Employing static excitation control and tie line reactance to stabilize wind turbine generators

NASA Technical Reports Server (NTRS)

Hwang, H. H.; Mozeico, H. V.; Guo, T.

1978-01-01

An analytical representation of a wind turbine generator is presented which employs blade pitch angle feedback control. A mathematical model was formulated. With the functioning MOD-0 wind turbine serving as a practical case study, results of computer simulations of the model as applied to the problem of dynamic stability at rated load are also presented. The effect of the tower shadow was included in the input to the system. Different configurations of the drive train, and optimal values of the tie line reactance were used in the simulations. Computer results revealed that a static excitation control system coupled with optimal values of the tie line reactance would effectively reduce oscillations of the power output, without the use of a slip clutch.

Manned Certification Tests of the Modernized MK 16 MOD 1

DTIC Science & Technology

2013-11-01

CERTIFICATION TESTS OF THE MODERNIZED MK 16 MOD 1 Authors: D. E . Warkander, Ph.D. D. J. Doolette, Ph.D...PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Dan E . Warkander; David J. Doolette; Paul C. Algra 5d. PROJECT NUMBER 5e. TASK NUMBER 10-08 5f. WORK UNIT...electronics must be turned on when calibrating the secondary display. 11 REFERENCES 1. R. P. Layton , Unmanned Evaluation of the Modernized MK 16 MOD

An automated process for generating archival data files from MATLAB figures

NASA Astrophysics Data System (ADS)

Wallace, G. M.; Greenwald, M.; Stillerman, J.

2016-10-01

A new directive from the White House Office of Science and Technology Policy requires that all publications supported by federal funding agencies (e.g. Department of Energy Office of Science, National Science Foundation) include machine-readable datasets for figures and tables. An automated script was developed at the PSFC to make this process easier for authors using the MATLAB plotting environment to create figures. All relevant data (x, y, z, errorbars) and metadata (line style, color, symbol shape, labels) are contained within the MATLAB .fig file created when saving a figure. The export_fig script extracts data and metadata from a .fig file and exports it into an HDF5 data file with no additional user input required. Support is included for a number of plot types including 2-D and 3-D line, contour, and surface plots, quiver plots, bar graphs, and histograms. This work supported by US Department of Energy cooperative agreement DE-FC02-99ER54512 using the Alcator C-Mod tokamak, a DOE Office of Science user facility.

LHC, le Big Bang en éprouvette

ScienceCinema

None

2017-12-09

Notre compréhension de l’Univers est en train de changer… Bar des Sciences - Tout public Débat modéré par Marie-Odile Montchicourt, journaliste de France Info. Evenement en vidéoconférence entre le Globe de la science et de l’innovation, le bar le Baloard de Montpellier et la Maison des Métallos à Paris. Intervenants au CERN : Philippe Charpentier et Daniel Froideveaux, physiciens au CERN. Intervenants à Paris : Vincent Bontemps, philosophe et chercheur au CEA ; Jacques Arnould, philosophe, historien des sciences et théologien, Jean-Jacques Beineix, réalisateur, producteur, scénariste de cinéma. Intervenants à Montpellier (LPTA) : André Neveu, physicien théoricien et directeur de recherche au CNRS ; Gilbert Moultaka, physicien théoricien et chargé de recherche au CNRS. Partenariat : CERN, CEA, IN2P3, Université MPL2 (LPTA) Dans le cadre de la Fête de la science 2008

Effect of milk replacer program on calf performance and digestion of nutrients with age of the dairy calf.

PubMed

Chapman, C E; Erickson, P S; Quigley, J D; Hill, T M; Bateman, H G; Suarez-Mena, F X; Schlotterbeck, R L

2016-04-01

Calves fed large amounts of milk replacer (MR) gain more body weight preweaning than calves fed less-aggressive programs; however, postweaning growth may be reduced. Limited research suggests that less than optimal digestion of the postweaned diet due to large amounts of MR with reduced dry feed intake preweaning may contribute to growth impairment postweaning. Current research was conducted to compare growth and postweaning digestion in 3-d-old male Holstein calves fed various MR programs. The MR programs were a conventional [CON; 0.44 kg of dry matter (DM) 21% crude protein (CP), 21% fat powder fed for 42d], moderate (MOD; 0.66 kg of DM 27% CP, 17% fat powder fed for 42d), and aggressive program (AGG; up to 0.87 kg of DM 27% CP, 17% fat powder fed for 49d). All calves were fed a 20% CP textured starter and water ad libitum for 56d. The trial used 96 calves (initially 41 ± 1.9 kg of body weight) received 5 wk apart in 2 groups of 48 calves. During d 51 to 56, fecal samples were collected from 5 calves per treatment randomly selected from calves in the first group. Selected nutrients and acid-insoluble ash (used as an internal flow marker) were analyzed in the starter and feces to estimate digestibility. Data were analyzed as a randomized complete block design with starting time of each group of calves as a block. Repeated measure analysis was performed on overall (0 to 56d) data. Means were separated with a protected least significant difference test. Pen was the experimental unit. Calves fed CON had the least average daily gain [CON=0.35, MOD=0.51, and AGG=0.55 kg/d; standard error of the mean (SEM)=0.018], feed efficiency (CON=0.35, MOD=0.49, and AGG=0.48 gain/feed, SEM=0.016), and change in hip width (CON=3.3, MOD=4.1, and AGG=4.1cm, SEM=0.20) compared with calves fed other programs. Calves fed AGG had the greatest change in BCS and least starter intake compared with calves fed the other programs. Digestibility of organic matter was 79, 78, and 68% and neutral detergent fiber was 54, 51, and 26% for calves fed programs CON, MOD, and AGG, respectively, and were least for calves fed AGG. These results indicate that postweaning digestion is lower than optimal and contributes to lower postweaning growth in calves fed aggressive compared with conventional or moderate MR programs. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Evaluation of Microscopic Observation Drug Susceptibility (MODS) and the string test for rapid diagnosis of pulmonary tuberculosis in HIV/AIDS patients in Bolivia.

PubMed

Lora, Meredith H; Reimer-McAtee, Melissa J; Gilman, Robert H; Lozano, Daniel; Saravia, Ruth; Pajuelo, Monica; Bern, Caryn; Castro, Rosario; Espinoza, Magaly; Vallejo, Maya; Solano, Marco; Challapa, Roxana; Torrico, Faustino

2015-06-06

Tuberculosis (TB) is the most common opportunistic infection and the leading cause of death in HIV-positive people worldwide. Diagnosing TB is difficult, and is more challenging in resource-scarce settings where culture-based diagnostic methods rely on poorly sensitive smear microscopy by Ziehl-Neelsen stain (ZN). We performed a cross-sectional study examining the diagnostic utility of Microscopic Observation Drug Susceptibility liquid culture (MODS) versus traditional Ziehl-Neelsen staining (ZN) and Lowenstein Jensen culture (LJ) of pulmonary tuberculosis (TB) and multidrug-resistant tuberculosis (MDRTB) in HIV-infected patients in Bolivia. For sputum scarce individuals we assessed the value of the string test and induced sputum for TB diagnosis. The presence of Mycobacterium tuberculosis (Mtb) in the sputum of 107 HIV-positive patients was evaluated by ZN, LJ, and MODS. Gastric secretion samples obtained by the string test were evaluated by MODS in 102 patients. The TB-HIV co-infection rate of HIV patients with respiratory symptoms by sputum sample was 45 % (48/107); 46/48 (96 %) were positive by MODS, 38/48 (79 %) by LJ, and 30/48 (63 %) by ZN. The rate of MDRTB was 9 % (4/48). Median time to positive culture was 10 days by MODS versus 34 days by LJ (p < 0.0001). In smear-negative patients, MODS detected TB in 17/18 patients, compared to 11/18 by LJ (94.4 % vs 61.0 %, p = 0.03 %). In patients unable to produce a sputum sample without induction, the string test cultured by MODS yielded Mtb in of 9/11 (82 %) TB positive patients compared to 11/11 (100 %) with induced sputum. Of the 10 patients unable to produce a sputum sample, 4 were TB-positive by string test. MODS was faster and had a higher Mtb detection yield compared to LJ, with a greater difference in yield between the two in smear-negative patients. The string test is a valuable diagnostic technique for HIV sputum-scarce or sputum-absent patients, and should be considered as an alternative test to induced sputum to obtain sample for Mtb in resource-limited settings. Nine percent of our TB+ patients had MDRTB, which reinforces the need for rapid detection with direct drug susceptibility testing in HIV patients in Bolivia.

Sensitivity of MODIS evapotranspiration algorithm (MOD16) to the acuracy of meteorological data and land use and land cover parameterization

NASA Astrophysics Data System (ADS)

Ruhoff, Anderson; Santini Adamatti, Daniela

2017-04-01

MODIS evapotranspiration (MOD16) is currently available with 1 km of spatial resolution over 109.03 Million km2 of vegetated land surface areas and this information is widely used to evaluate the linkages between hydrological, energy and carbon cycles. The algorithm is driven by meteorological reanalysis data and MODIS remotely-sensed data, which include land use and land cover classification (MCD12Q1), leaf area index (LAI) and fraction of absorbed photosynthetically active radiation (FPAR) (MOD15A2) and albedo (MOD43b3). For calibration and parameterization, the algorithm uses a Biome Property Look-up Table (BPLUT) based on MCD12Q1 land cover classification. Several studies evaluated MOD16 accuracy using evapotranspiration measurements and water balance analysis, showing that this product can reproduce global evapotranspiration effectively under a variety climate condition, from local to wide-basin scale, with uncertainties up to 25%. In this study, we evaluated the sensitivity of MOD16 algorithm to land use and land cover parameterization and to meteorological data. Considering that MCD12Q1 has an accuracy between 70 and 85% at continental scale, we changed land cover parametererization to understand the influence of land use and land cover classification on MOD16 evapotranspiration estimations. Knowing that meteorological reanalysis data also have uncertainties (mostly related to the coarse spatial resolution), we compared MOD16 evapotranspiration driven by observed meteorological data to those driven by the reanalysis data. Our analysis were carried in South America, with evapotranspiration and meteorological measurements from the Large-Scale Biosphere-Atmosphere Experiment in Amazonia (LBA) at 8 different sites, including tropical rainforest, tropical dry forest, selective logged forest, seasonal flooded forest and pasture/agriculture. Our results indicate that land use and land cover classification has a strong influence on MOD16 algorithm. The use of incorrect parametererization due to land use and land cover misclassification can introduce large erros in estimates of evapotranspiration. We also found that the biases in meteorological reanalysis data can introduce considerable errors into the estimations. Overall, there is a significant potential for mapping and monitoring global evapotranspiration using MODIS remotely-sensed images combined to meteorological reanalysis data.

Soluble tumor necrosis factor receptor p55 predicts cytokinemia and systemic inflammatory response after cardiopulmonary bypass.

PubMed

el-Barbary, Mahmoud; Khabar, Khalid S A

2002-08-01

To examine the behavior of soluble tumor necrosis factor (TNF) receptors in circulation before and after cardiopulmonary bypass and the relationship to the development of cytokinemia and acute complications comprising systemic inflammatory response syndrome (SIRS) and multiple organ dysfunction syndrome (MODS). The predictive value of soluble TNF receptor is assessed herein. Prospective study comparing prebypass and postbypass levels in patients with and without complications indicative of SIRS and MODS. Cardiac surgical intensive care unit in a tertiary care hospital. A total of 20 pediatric patients who underwent cardiopulmonary bypass during open heart surgery. Blood samples were collected from catheters before and 2 hrs and 24 hrs after the onset of bypass. We measured plasma levels of soluble TNF receptors by using enzyme-linked immunosorbent assay in 20 patients before and after cardiopulmonary bypass. Clinical data, including duration of bypass and tests or signs indicative of SIRS/MODS, were collected. Soluble TNF receptor I (p55 sR), significantly increased (2241 +/- 312 pg/mL) at 2 hrs after bypass (p <.0005) and remained elevated (2826 +/- 695 pg/mL) at 1 day after bypass (p <.005) when compared with prebypass levels (725 +/- 130 pg/mL). Patients with the acute complications of SIRS/MODS had a higher ratio of postbypass to prebypass p55 sR levels (5.0-fold, p <.001) when compared with patients with no SIRS/MODS (1.75-fold). Remarkably, before surgery, levels of TNF p55 sR predict both cytokinemia (r =.67 to.73, p <.05) and SIRS/MODS (p <.01). The prebypass levels of TNF p55 sR were consistently higher (range, 1000-1400 pg/mL) in patients who subsequently developed SIRS/MODS than the levels (range, 400-570 pg/mL) in patients who did not develop SIRS/MODS. Hypotension, respiratory dysfunctions, and coagulopathy were particularly more prevailing (p <.005) among the complications that were associated with high prebypass levels of TNF p55 sR. Soluble TNF receptor p55 can be employed as a predictive marker for cytokinemia and the development of SIRS/MODS that may arise from a major insult to the body such as cardiopulmonary bypass.

Utility of behavioral versus cognitive measures in differentiating between subtypes of frontotemporal lobar degeneration and Alzheimer's disease.

PubMed

Heidler-Gary, Jennifer; Gottesman, Rebecca; Newhart, Melissa; Chang, Shannon; Ken, Lynda; Hillis, Argye E

2007-01-01

We hypothesized that a modified version of the Frontal Behavioral Inventory (FBI-mod), along with a few cognitive tests, would be clinically useful in distinguishing between clinically defined Alzheimer's disease (AD) and subtypes of frontotemporal lobar degeneration (FTLD): frontotemporal dementia (dysexecutive type), progressive nonfluent aphasia, and semantic dementia. We studied 80 patients who were diagnosed with AD (n = 30) or FTLD (n = 50), on the basis of a comprehensive neuropsychological battery, imaging, neurological examination, and history. We found significant between-group differences on the FBI-mod, two subtests of the Rey Auditory Verbal Learning Test (verbal learning and delayed recall), and the Trail Making Test Part B (one measure of 'executive functioning'). AD was characterized by relatively severe impairment in verbal learning, delayed recall, and executive functioning, with relatively normal scores on the FBI-mod. Frontotemporal dementia was characterized by relatively severe impairment on the FBI-mod and executive functioning in the absence of severe impairment in verbal learning and recall. Progressive nonfluent aphasia was characterized by severe impairment in executive functioning with relatively normal scores on verbal learning and recall and FBI-mod. Finally, semantic dementia was characterized by relatively severe deficits in delayed recall, but relatively normal performance on new learning, executive functioning, and on FBI-mod. Discriminant function analysis confirmed that the FBI-mod, in conjunction with the Rey Auditory Verbal Learning Test, and the Trail Making Test Part B categorized the majority of patients as subtypes of FTLD or AD in the same way as a full neuropsychological battery, neurological examination, complete history, and imaging. These tests may be useful for efficient clinical diagnosis, although progressive nonfluent aphasia and semantic dementia are likely to be best distinguished by language tests not included in standard neuropsychological test batteries.

Perceived vulnerability moderates the relations between the use of protective behavioral strategies and alcohol use and consequences among high-risk young adults.

PubMed

Garcia, Tracey A; Fairlie, Anne M; Litt, Dana M; Waldron, Katja A; Lewis, Melissa A

2018-06-01

Drinking protective behavioral strategies (PBS) have been associated with reductions in alcohol use and alcohol-related consequences in young adults. PBS subscales, Limiting/Stopping (LS), Manner of Drinking (MOD), and Serious Harm Reduction (SHR), have been examined in the literature; LS, MOD, and SHR have mixed support as protective factors. Understanding moderators between PBS and alcohol use and related consequences is an important development in PBS research in order to delineate when and for whom PBS use is effective in reducing harm from alcohol use. Perceptions of vulnerability to negative consequences, included in health-risk models, may be one such moderator. The current study examined whether two types of perceived vulnerability (perceived vulnerability when drinking; perceived vulnerability in uncomfortable/unfamiliar situations) moderated the relations between LS, MOD, SHR strategies and alcohol use and related negative consequences. High-risk young adults (N = 400; 53.75% female) recruited nationally completed measures of PBS, alcohol use and related consequences, and measures of perceived vulnerability. Findings demonstrated that perceived vulnerability when drinking moderated the relations between MOD strategies and alcohol use. The interactions between perceived vulnerability when drinking and PBS did not predict alcohol-related consequences. Perceived vulnerability in unfamiliar/uncomfortable social situations moderated relations between MOD strategies and both alcohol use and related negative consequences; no other significant interactions emerged. Across both perceived vulnerability types and MOD strategies, those with the highest levels of perceived vulnerability and who used MOD strategies the most had the greatest decrements in alcohol use and related negative consequences. Prevention and intervention implications are discussed. Copyright © 2018. Published by Elsevier Ltd.

R-HyMOD: an R-package for the hydrological model HyMOD

NASA Astrophysics Data System (ADS)

Baratti, Emanuele; Montanari, Alberto

2015-04-01

A software code for the implementation of the HyMOD hydrological model [1] is presented. HyMOD is a conceptual lumped rainfall-runoff model that is based on the probability-distributed soil storage capacity principle introduced by R. J. Moore 1985 [2]. The general idea behind this model is to describe the spatial variability of some process parameters as, for instance, the soil structure or the water storage capacities, through probability distribution functions. In HyMOD, the rainfall-runoff process is represented through a nonlinear tank connected with three identical linear tanks in parallel representing the surface flow and a slow-flow tank representing groundwater flow. The model requires the optimization of five parameters: Cmax (the maximum storage capacity within the watershed), β (the degree of spatial variability of the soil moisture capacity within the watershed), α (a factor for partitioning the flow between two series of tanks) and the two residence time parameters of quick-flow and slow-flow tanks, kquick and kslow respectively. Given its relatively simplicity but robustness, the model is widely used in the literature. The input data consist of precipitation and potential evapotranspiration at the given time scale. The R-HyMOD package is composed by a 'canonical' R-function of HyMOD and a fast FORTRAN implementation. The first one can be easily modified and can be used, for instance, for educational purposes; the second part combines the R user friendly interface with a fast processing unit. [1] Boyle D.P. (2000), Multicriteria calibration of hydrological models, Ph.D. dissertation, Dep. of Hydrol. and Water Resour., Univ of Arizona, Tucson. [2] Moore, R.J., (1985), The probability-distributed principle and runoff production at point and basin scale, Hydrol. Sci. J., 30(2), 273-297.

Methodology, status, and plans for development and assessment of the RELAP5 code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, G.W.; Riemke, R.A.

1997-07-01

RELAP/MOD3 is a computer code used for the simulation of transients and accidents in light-water nuclear power plants. The objective of the program to develop and maintain RELAP5 was and is to provide the U.S. Nuclear Regulatory Commission with an independent tool for assessing reactor safety. This paper describes code requirements, models, solution scheme, language and structure, user interface validation, and documentation. The paper also describes the current and near term development program and provides an assessment of the code`s strengths and limitations.

The Depth Limits of Eddy Current Testing for Defects: A Computational Investigation and Smooth-Shaped Defect Synthesis from Finite Element Optimization

DTIC Science & Technology

2015-04-22

AND SUBTITLE 5a. CONTRACT NUMBER W56HZV-07-2-0001 W56HZV-08- C - 0236 The Depth Limits of Eddy Current Testing for Defects: A...Unlimited b. ABSTRACT Unlimited c . THIS PAGE Unlimited Unlimited 12 19b. TELEPHONE NUMBER (include area code) 586-282-6471 Standard Form 298...Dave Gunter, Acting Associate Director, Analytics, US Army TARDEC  Dr. Dave Horner, Director, DoD HPC Mod Program  Mr. Steve Knott , Deputy

Dynamic Network Security Control Using Software Defined Networking

DTIC Science & Technology

2016-03-24

Most importantly I thank my family for understanding, loving , and thriving in the hectic world of military spouse and children. Michael C. Todd v...RBAC poses access to objects as a user to member-of group relationship . This construct results in a set of rules to govern access to objects based...API. Agent Agent.py Event.py Message.py ModSysStatus.py Event Message ModSysStatus Event - Message - ModSysStatus Relationship Figure 12. Agent Design

A New Ferroelectric Varactor from Water Based Inorganic Precursors

DTIC Science & Technology

2003-04-03

See Equation 2). 0 0 4 OH +-)4T H13< Equation 2. Idealized Reaction of Titanium Isopropoxide with 2-ethylhexanoic acid. Inconsistent results with the...Equation 3). Equation 3. Reaction of 2-ethylhexanoic anhydride with Titanium Isopropoxide We have made over one hundred batches of both BST and SBTN MOD...aliphatic acids used in the more common MOD precursors. Equation 4 shows a comparison of the decomposition products of Titanium MOD precursors made from 2

Air Force Intercontinental Ballistic Missile Fuze Modernization (ICBM Fuze Mod)

DTIC Science & Technology

2015-12-01

Selected Acquisition Report ( SAR ) RCS: DD-A&T(Q&A)823-498 Air Force Intercontinental Ballistic Missile Fuze Modernization (ICBM Fuze Mod) As of FY...2015 SAR March 17, 2016 09:03:03 UNCLASSIFIED 2 Table of Contents Common Acronyms and Abbreviations for MDAP Programs 3 Program Information...Acquisition Unit Cost ICBM Fuze Mod December 2015 SAR March 17, 2016 09:03:03 UNCLASSIFIED 3 PB - President’s Budget PE - Program Element PEO - Program

The MOD-1 steel blade

NASA Technical Reports Server (NTRS)

Vanbronkhorst, J.

1979-01-01

The design, development, fabrication, testing, and transport of two 100 foot metal blades for the MOD-1 WTS are summarized. Because the metal blade design was started late in the MOD-1 system development, many of the design requirements (allocations) were restrictive for the metal blade concept, particularly the maximum weight requirement. The design solutions required to achieve the weight goal resulted in a labor intensive (expensive) fabrication, particularly for a quantity of only two blades manufactured using minimal tooling.

Comparison of Measurements and FluorMOD Simulations for Solar Induced Chlorophyll Fluorescence and Reflectance of a Corn Crop under Nitrogen Treatments [SIF and Reflectance for Corn

NASA Technical Reports Server (NTRS)

Middleton, Elizabeth M.; Corp, Lawrence A.; Campbell, Petya K. E.

2007-01-01

The FLuorescence Explorer (FLEX) satellite concept is one of six semifinalist mission proposals selected in 2006 for pre-Phase studies by the European Space Agency (ESA). The FLEX concept proposes to measure passive solar induced chlorophyll fluorescence (SIF) of terrestrial ecosystems. A new spectral vegetation Fluorescence Model (FluorMOD) was developed to include the effects of steady state SIF on canopy reflectance. We used our laboratory and field measurements previously acquired from foliage and canopies of corn (Zea mays L.) under controlled nitrogen (N) fertilization to parameterize and evaluate FluorMOD. Our data included biophysical properties, fluorescence (F) and reflectance spectra for leaves; reflectance spectra of canopies and soil; solar irradiance; plot-level leaf area index; and canopy SIF emissions determined using the Fraunhofer Line Depth principal for the atmospheric telluric oxygen absorption features at 688 nm (O2-beta) and 760 nm (O2-alpha). FluorMOD simulations implemented in the default "look-up-table" mode did not reproduce the observed magnitudes of leaf F, canopy SIF, or canopy reflectance. However, simulations for all of these parameters agreed with observations when the default FluorMOD information was replaced with measurements, although N treatment responses were underestimated. Recommendations were provided to enhance FluorMOD's potential utility in support of SIF field experiments and studies of agriculture and ecosystems.

Experience and assessment of the DOE-NASA Mod-1 2000-Kilowatt wind turbine generator at Boone, North Carolina

NASA Technical Reports Server (NTRS)

Collins, J. L.; Shaltenc, R. K.; Poor, R. H.; Barton, R. S.

1982-01-01

The Mod 1 program objectives are defined. The Mod 1 wind turbine is described. In addition to the steel blade operated on the wind turbine, a composite blade was designed and manufactured. During the early phase of the manufacturing cycle of Mod 1A configuration was designed that identified concepts such as partial span control, a soft tower, and upwind teetered rotors that were incorporated in second and third generation industry designs. The Mod 1 electrical system performed as designed, with voltage flicker characteristics within acceptable utility limits. Power output versus wind speed equaled or exceeded design predictions. The wind turbine control system was operated successfully at the site and remotely from the utility dispatcher's office. During wind turbine operations, television interference was experienced by the local residents. As a consequence, operations were restricted. Although not implemented, two potential solutions were identified. In addition to television interference, a few local residents complained bout objectionable sound, particularly the 'thump' as the blade passed behind the tower. To eliminate objections, the sound generation level was reduced by 10 dB by reducing the rotor speed from 35 rpm to 23 rpm. Bolts in the drive train fractured. A solution was identified but not implemented. The public reaction toward the Mod 1 wind turbine program was overwhelmingly favorable.

Protease-resistant modified human β-hexosaminidase B ameliorates symptoms in GM2 gangliosidosis model

PubMed Central

Mizutani, Yasumichi; Sugiyama, Eiji; Tasaki, Chikako; Tsuji, Daisuke; Maita, Nobuo; Hirokawa, Takatsugu; Asanuma, Daisuke; Kamiya, Mako; Sato, Kohei; Setou, Mitsutoshi; Urano, Yasuteru; Togawa, Tadayasu; Otaka, Akira; Sakuraba, Hitoshi

2016-01-01

GM2 gangliosidoses, including Tay-Sachs and Sandhoff diseases, are neurodegenerative lysosomal storage diseases that are caused by deficiency of β-hexosaminidase A, which comprises an αβ heterodimer. There are no effective treatments for these diseases; however, various strategies aimed at restoring β-hexosaminidase A have been explored. Here, we produced a modified human hexosaminidase subunit β (HexB), which we have termed mod2B, composed of homodimeric β subunits that contain amino acid sequences from the α subunit that confer GM2 ganglioside–degrading activity and protease resistance. We also developed fluorescent probes that allow visualization of endocytosis of mod2B via mannose 6-phosphate receptors and delivery of mod2B to lysosomes in GM2 gangliosidosis models. In addition, we applied imaging mass spectrometry to monitor efficacy of this approach in Sandhoff disease model mice. Following i.c.v. administration, mod2B was widely distributed and reduced accumulation of GM2, asialo-GM2, and bis(monoacylglycero)phosphate in brain regions including the hypothalamus, hippocampus, and cerebellum. Moreover, mod2B administration markedly improved motor dysfunction and a prolonged lifespan in Sandhoff disease mice. Together, the results of our study indicate that mod2B has potential for intracerebrospinal fluid enzyme replacement therapy and should be further explored as a gene therapy for GM2 gangliosidoses. PMID:27018595

Protease-resistant modified human β-hexosaminidase B ameliorates symptoms in GM2 gangliosidosis model.

PubMed

Kitakaze, Keisuke; Mizutani, Yasumichi; Sugiyama, Eiji; Tasaki, Chikako; Tsuji, Daisuke; Maita, Nobuo; Hirokawa, Takatsugu; Asanuma, Daisuke; Kamiya, Mako; Sato, Kohei; Setou, Mitsutoshi; Urano, Yasuteru; Togawa, Tadayasu; Otaka, Akira; Sakuraba, Hitoshi; Itoh, Kohji

2016-05-02

GM2 gangliosidoses, including Tay-Sachs and Sandhoff diseases, are neurodegenerative lysosomal storage diseases that are caused by deficiency of β-hexosaminidase A, which comprises an αβ heterodimer. There are no effective treatments for these diseases; however, various strategies aimed at restoring β-hexosaminidase A have been explored. Here, we produced a modified human hexosaminidase subunit β (HexB), which we have termed mod2B, composed of homodimeric β subunits that contain amino acid sequences from the α subunit that confer GM2 ganglioside-degrading activity and protease resistance. We also developed fluorescent probes that allow visualization of endocytosis of mod2B via mannose 6-phosphate receptors and delivery of mod2B to lysosomes in GM2 gangliosidosis models. In addition, we applied imaging mass spectrometry to monitor efficacy of this approach in Sandhoff disease model mice. Following i.c.v. administration, mod2B was widely distributed and reduced accumulation of GM2, asialo-GM2, and bis(monoacylglycero)phosphate in brain regions including the hypothalamus, hippocampus, and cerebellum. Moreover, mod2B administration markedly improved motor dysfunction and a prolonged lifespan in Sandhoff disease mice. Together, the results of our study indicate that mod2B has potential for intracerebrospinal fluid enzyme replacement therapy and should be further explored as a gene therapy for GM2 gangliosidoses.

MODIS Collection 6 Clear Sky Restoral (CSR): Filtering Cloud Mast 'Not Clear' Pixels

NASA Technical Reports Server (NTRS)

Meyer, Kerry G.; Platnick, Steven Edward; Wind, Galina; Riedi, Jerome

2014-01-01

Correctly identifying cloudy pixels appropriate for the MOD06 cloud optical and microphysical property retrievals is accomplished in large part using results from the MOD35 1km cloud mask tests (note there are also two 250m subpixel cloud mask tests that can convert the 1km cloudy designations to clear sky). However, because MOD35 is by design clear sky conservative (i.e., it identifies "not clear" pixels), certain situations exist in which pixels identified by MOD35 as "cloudy" are nevertheless likely to be poor retrieval candidates. For instance, near the edge of clouds or within broken cloud fields, a given 1km MODIS field of view (FOV) may in fact only be partially cloudy. This can be problematic for the MOD06 retrievals because in these cases the assumptions of a completely overcast homogenous cloudy FOV and 1-dimensional plane-parallel radiative transfer no longer hold, and subsequent retrievals will be of low confidence. Furthermore, some pixels may be identified by MOD35 as "cloudy" for reasons other than the presence of clouds, such as scenes with thick smoke or lofted dust, and should therefore not be retrieved as clouds. With such situations in mind, a Clear Sky Restoral (CSR) algorithm was introduced in C5 that attempts to identify pixels expected to be poor retrieval candidates. Table 1 provides SDS locations for CSR and partly cloudy (PCL) pixels.

Sur la modélisation des supraconducteurs : le ``modèle de l'état critique'' de Bean, en trois dimensions

NASA Astrophysics Data System (ADS)

Bossavit, A.

1993-03-01

Macroscopic modelling of superconductors demands a substitution of some nonlinear behavior law for Ohm's law. For this, a version of Bean's “critical state” model, derived from the setting of a convex functional of the current density field, valid in dimension 3 without any previous assumption about the direction of currents, is proposed. It is shown how two standard three-dimensional finite element methods (“h-formulation” and “e-formulation”), once fitted with this model, can deal with situations were superconductors are present. La modélisation macroscopique des supraconducteurs suppose le remplacement de la loi d'Ohm par une loi de comportement non linéaire adéquate. On présente à cet effet une version du “modèle de Bean”, ou modèle de l'état critique, basée sur la construction d'une certaine fonctionnelle convexe du champ des densités de courant, qui est valable en dimension 3 sans hypothèses préalables sur la direction des courants. On montre comment adapter deux méthodes standards de calcul de courants de Foucault par élérnents finis en trois dimensions (“en h” et “en e”) à la présence de supraconducteurs, en incorporant ce modèle.

Disruption Warning Database Development and Exploratory Machine Learning Studies on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Montes, Kevin; Rea, Cristina; Granetz, Robert

2017-10-01

A database of about 1800 shots from the 2015 campaign on the Alcator C-Mod tokamak is assembled, including disruptive and non-disruptive discharges. The database consists of 40 relevant plasma parameters with data taken from 160k time slices. In order to investigate the possibility of developing a robust disruption prediction algorithm that is tokamak-independent, we focused machine learning studies on a subset of dimensionless parameters such as βp, n /nG , etc. The Random Forests machine learning algorithm provides insight on the available data set by ranking the relative importance of the input features. Its application on the C-Mod database, however, reveals that virtually no one parameter has more importance than any other, and that its classification algorithm has a low rate of successfully predicted samples, as well as poor false positive and false negative rates. Comparing the analysis of this algorithm on the C-Mod database with its application to a similar database on DIII-D, we conclude that disruption prediction may not be feasible on C-Mod. This conclusion is supported by empirical observations that most C-Mod disruptions are caused by radiative collapse due to molybdenum from the first wall, which happens on just a 1-2ms timescale. Supported by the US Dept. of Energy under DE-FC02-99ER54512 and DE-FC02-04ER54698.

Multi-scale gyrokinetic simulation of Alcator C-Mod tokamak discharges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, N. T., E-mail: nthoward@psfc.mit.edu; White, A. E.; Greenwald, M.

2014-03-15

Alcator C-Mod tokamak discharges have been studied with nonlinear gyrokinetic simulation simultaneously spanning both ion and electron spatiotemporal scales. These multi-scale simulations utilized the gyrokinetic model implemented by GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] and the approximation of reduced electron mass (μ = (m{sub D}/m{sub e}){sup .5} = 20.0) to qualitatively study a pair of Alcator C-Mod discharges: a low-power discharge, previously demonstrated (using realistic mass, ion-scale simulation) to display an under-prediction of the electron heat flux and a high-power discharge displaying agreement with both ion and electron heat flux channels [N. T. Howard et al.,more » Nucl. Fusion 53, 123011 (2013)]. These multi-scale simulations demonstrate the importance of electron-scale turbulence in the core of conventional tokamak discharges and suggest it is a viable candidate for explaining the observed under-prediction of electron heat flux. In this paper, we investigate the coupling of turbulence at the ion (k{sub θ}ρ{sub s}∼O(1.0)) and electron (k{sub θ}ρ{sub e}∼O(1.0)) scales for experimental plasma conditions both exhibiting strong (high-power) and marginally stable (low-power) low-k (k{sub θ}ρ{sub s} < 1.0) turbulence. It is found that reduced mass simulation of the plasma exhibiting marginally stable low-k turbulence fails to provide even qualitative insight into the turbulence present in the realistic plasma conditions. In contrast, multi-scale simulation of the plasma condition exhibiting strong turbulence provides valuable insight into the coupling of the ion and electron scales.« less

Quantitative comparison of electron temperature fluctuations to nonlinear gyrokinetic simulations in C-Mod Ohmic L-mode discharges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sung, C., E-mail: csung@physics.ucla.edu; White, A. E.; Greenwald, M.

2016-04-15

Long wavelength turbulent electron temperature fluctuations (k{sub y}ρ{sub s} < 0.3) are measured in the outer core region (r/a > 0.8) of Ohmic L-mode plasmas at Alcator C-Mod [E. S. Marmar et al., Nucl. Fusion 49, 104014 (2009)] with a correlation electron cyclotron emission diagnostic. The relative amplitude and frequency spectrum of the fluctuations are compared quantitatively with nonlinear gyrokinetic simulations using the GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] in two different confinement regimes: linear Ohmic confinement (LOC) regime and saturated Ohmic confinement (SOC) regime. When comparing experiment with nonlinear simulations, it is found that local,more » electrostatic ion-scale simulations (k{sub y}ρ{sub s} ≲ 1.7) performed at r/a ∼ 0.85 reproduce the experimental ion heat flux levels, electron temperature fluctuation levels, and frequency spectra within experimental error bars. In contrast, the electron heat flux is robustly under-predicted and cannot be recovered by using scans of the simulation inputs within error bars or by using global simulations. If both the ion heat flux and the measured temperature fluctuations are attributed predominantly to long-wavelength turbulence, then under-prediction of electron heat flux strongly suggests that electron scale turbulence is important for transport in C-Mod Ohmic L-mode discharges. In addition, no evidence is found from linear or nonlinear simulations for a clear transition from trapped electron mode to ion temperature gradient turbulence across the LOC/SOC transition, and also there is no evidence in these Ohmic L-mode plasmas of the “Transport Shortfall” [C. Holland et al., Phys. Plasmas 16, 052301 (2009)].« less

Preventing and Treating Hypoxia: Using a Physiology Simulator to Demonstrate the Value of Pre-Oxygenation and the Futility of Hyperventilation.

PubMed

Lerant, Anna A; Hester, Robert L; Coleman, Thomas G; Phillips, William J; Orledge, Jeffrey D; Murray, W Bosseau

2015-01-01

Insufficient pre-oxygenation before emergency intubation, and hyperventilation after intubation are mistakes that are frequently observed in and outside the operating room, in clinical practice and in simulation exercises. Physiological parameters, as appearing on standard patient monitors, do not alert to the deleterious effects of low oxygen saturation on coronary perfusion, or that of low carbon dioxide concentrations on cerebral perfusion. We suggest the use of HumMod, a computer-based human physiology simulator, to demonstrate beneficial physiological responses to pre-oxygenation and the futility of excessive minute ventilation after intubation. We programmed HumMod, to A.) compare varying times (0-7 minutes) of pre-oxygenation on oxygen saturation (SpO2) during subsequent apnoea; B.) simulate hyperventilation after apnoea. We compared the effect of different minute ventilation rates on SpO2, acid-base status, cerebral perfusion and other haemodynamic parameters. A.) With no pre-oxygenation, starting SpO2 dropped from 98% to 90% in 52 seconds with apnoea. At the other extreme, following full pre-oxygenation with 100% O2 for 3 minutes or more, the SpO2 remained 100% for 7.75 minutes during apnoea, and dropped to 90% after another 75 seconds. B.) Hyperventilation, did not result in more rapid normalization of SpO2, irrespective of the level of minute ventilation. However, hyperventilation did cause significant decreases in cerebral blood flow (CBF). HumMod accurately simulates the physiological responses compared to published human studies of pre-oxygenation and varying post intubation minute ventilations, and it can be used over wider ranges of parameters than available in human studies and therefore available in the literature.

Preventing and Treating Hypoxia: Using a Physiology Simulator to Demonstrate the Value of Pre-Oxygenation and the Futility of Hyperventilation

PubMed Central

Lerant, Anna A.; Hester, Robert L.; Coleman, Thomas G.; Phillips, William J.; Orledge, Jeffrey D.; Murray, W. Bosseau

2015-01-01

Introduction: Insufficient pre-oxygenation before emergency intubation, and hyperventilation after intubation are mistakes that are frequently observed in and outside the operating room, in clinical practice and in simulation exercises. Physiological parameters, as appearing on standard patient monitors, do not alert to the deleterious effects of low oxygen saturation on coronary perfusion, or that of low carbon dioxide concentrations on cerebral perfusion. We suggest the use of HumMod, a computer-based human physiology simulator, to demonstrate beneficial physiological responses to pre-oxygenation and the futility of excessive minute ventilation after intubation. Methods: We programmed HumMod, to A.) compare varying times (0-7 minutes) of pre-oxygenation on oxygen saturation (SpO2) during subsequent apnoea; B.) simulate hyperventilation after apnoea. We compared the effect of different minute ventilation rates on SpO2, acid-base status, cerebral perfusion and other haemodynamic parameters. Results: A.) With no pre-oxygenation, starting SpO2 dropped from 98% to 90% in 52 seconds with apnoea. At the other extreme, following full pre-oxygenation with 100% O2 for 3 minutes or more, the SpO2 remained 100% for 7.75 minutes during apnoea, and dropped to 90% after another 75 seconds. B.) Hyperventilation, did not result in more rapid normalization of SpO2, irrespective of the level of minute ventilation. However, hyperventilation did cause significant decreases in cerebral blood flow (CBF). Conclusions: HumMod accurately simulates the physiological responses compared to published human studies of pre-oxygenation and varying post intubation minute ventilations, and it can be used over wider ranges of parameters than available in human studies and therefore available in the literature. PMID:26283881

Investigation of the critical edge ion heat flux for L-H transitions in Alcator C-Mod and its dependence on B T

NASA Astrophysics Data System (ADS)

Schmidtmayr, M.; Hughes, J. W.; Ryter, F.; Wolfrum, E.; Cao, N.; Creely, A. J.; Howard, N.; Hubbard, A. E.; Lin, Y.; Reinke, M. L.; Rice, J. E.; Tolman, E. A.; Wukitch, S.; Ma, Y.; ASDEX Upgrade Team; Alcator C-Mod Team

2018-05-01

This paper presents investigations on the role of the edge ion heat flux for transitions from L-mode to H-mode in Alcator C-Mod. Previous results from the ASDEX Upgrade tokamak indicated that a critical value of edge ion heat flux per particle is needed for the transition. Analysis of C-Mod data confirms this result. The edge ion heat flux is indeed found to increase linearly with density at given magnetic field and plasma current. Furthermore, the Alcator C-Mod data indicate that the edge ion heat flux at the L-H transition also increases with magnetic field. Combining the data from Alcator C-Mod and ASDEX Upgrade yields a general expression for the edge ion heat flux at the L-H transition. These results are discussed from the point of view of the possible physics mechanism of the L-H transition. They are also compared to the L-H power threshold scaling and an extrapolation for ITER is given.

Know Your Discipline: Teaching the Philosophy of Computer Science

ERIC Educational Resources Information Center

Tedre, Matti

2007-01-01

The diversity and interdisciplinarity of computer science and the multiplicity of its uses in other sciences make it hard to define computer science and to prescribe how computer science should be carried out. The diversity of computer science also causes friction between computer scientists from different branches. Computer science curricula, as…

Regional cardiac function analysis from tagged MRI images. Comparison of techniques: Harmonic-Phase (HARP) versus Sinusoidal-Modeling (SinMod) analysis.

PubMed

Ibrahim, El-Sayed H; Stojanovska, Jadranka; Hassanein, Azza; Duvernoy, Claire; Croisille, Pierre; Pop-Busui, Rodica; Swanson, Scott D

2018-05-16

Cardiac MRI tagging is a valuable technique for evaluating regional heart function. Currently, there are a number of different techniques for analyzing the tagged images. Specifically, k-space-based analysis techniques showed to be much faster than image-based techniques, where harmonic-phase (HARP) and sine-wave modeling (SinMod) stand as two famous techniques of the former group, which are frequently used in clinical studies. In this study, we compared HARP and SinMod and studied inter-observer variability between the two techniques for evaluating myocardial strain and apical-to-base torsion in numerical phantom, nine healthy controls, and thirty diabetic patients. Based on the ground-truth numerical phantom measurements (strain = -20% and rotation angle = -4.4°), HARP and SinMod resulted in overestimation (in absolute value terms) of strain by 1% and 5% (strain values), and of rotation angle by 0.4° and 2.0°, respectively. For the in-vivo results, global strain and torsion ranges were -10.6 to -35.3% and 1.8-12.7°/cm in patients, and -17.8 to -32.7% and 1.8-12.3°/cm in volunteers. On average, SinMod overestimated strain measurements by 5.7% and 5.9% (strain values) in the patients and volunteers, respectively, compared to HARP, and overestimated torsion measurements by 2.9°/cm and 2.5°/cm in the patients and volunteers, respectively, compared to HARP. Location-wise, the ranges for basal, mid-ventricular, and apical strain in patients (volunteers) were -8.4 to -31.5% (-11.6 to -33.3%), -6.3 to -37.2% (-17.8 to -33.3%), and -5.2 to -38.4% (-20.0 to -33.2%), respectively. SinMod overestimated strain in the basal, mid-ventricular, and apical slices by 4.7% (5.7%), 5.9% (5.5%), and 8.9% (6.8%), respectively, compared to HARP in the patients (volunteers). Nevertheless, there existed good correlation between the HARP and SinMod measurements. Finally, there were no significant strain or torsion measurement differences between patients and volunteers. There existed good inter-observer agreement, as all measurement differences lied within the Bland-Altman ± 2 standard-deviation (SD) difference limits. In conclusion, despite the consistency of the results by either HARP or SinMod and acceptable agreement of the generated strain and torsion patterns by both techniques, SinMod systematically overestimated the measurements compared to HARP. Under current operating conditions, the measurements from HARP and SinMod cannot be used interchangeably. Copyright © 2017. Published by Elsevier Inc.

An Apple II Implementation of Man-Mod Manpower Planning Model.

DTIC Science & Technology

1982-03-01

next page. It is highly recommended, to prevent the loss of data, that the user save the data at this point. If Choice (1 ), yes, is selected, the...approximately 30 seconds, but will clear and reload memory preventing any inadvertent memory changes which might cause program interruptions or erroneous cal... prgram . 70 MAN-MOD/PROGRAM (PROGRAM LISTING) 1000 REM MAN-MOD/PROGRAM PROGRAM: "FOR" IS IN QUOTES IN LINES 1004,10518,10520,10524,10526,10528,1072

Spatio-temporal Change Patterns of Tropical Forests from 2000 to 2014 Using MOD09A1 Dataset

NASA Astrophysics Data System (ADS)

Qin, Y.; Xiao, X.; Dong, J.

2016-12-01

Large-scale deforestation and forest degradation in the tropical region have resulted in extensive carbon emissions and biodiversity loss. However, restricted by the availability of good-quality observations, large uncertainty exists in mapping the spatial distribution of forests and their spatio-temporal changes. In this study, we proposed a pixel- and phenology-based algorithm to identify and map annual tropical forests from 2000 to 2014, using the 8-day, 500-m MOD09A1 (v005) product, under the support of Google cloud computing (Google Earth Engine). A temporal filter was applied to reduce the random noises and to identify the spatio-temporal changes of forests. We then built up a confusion matrix and assessed the accuracy of the annual forest maps based on the ground reference interpreted from high spatial resolution images in Google Earth. The resultant forest maps showed the consistent forest/non-forest, forest loss, and forest gain in the pan-tropical zone during 2000 - 2014. The proposed algorithm showed the potential for tropical forest mapping and the resultant forest maps are important for the estimation of carbon emission and biodiversity loss.

Assessment of RELAP5/MOD2 against a pressurizer spray valve inadverted fully opening transient and recovery by natural circulation in Jose Cabrera Nuclear Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arroyo, R.; Rebollo, L.

1993-06-01

This document presents the comparison between the simulation results and the plant measurements of a real event that took place in JOSE CABRERA nuclear power plant in August 30th, 1984. The event was originated by the total, continuous and inadverted opening of the pressurizer spray valve PCV-400A. JOSE CABRERA power plant is a single loop Westinghouse PWR belonging to UNION ELECTRICA FENOSA, S.A. (UNION FENOSA), an Spanish utility which participates in the International Code Assessment and Applications Program (ICAP) as a member of UNIDAD ELECTRICA, S.A. (UNESA). This is the second of its two contributions to the Program: the firstmore » one was an application case and this is an assessment one. The simulation has been performed using the RELAP5/MOD2 cycle 36.04 code, running on a CDC CYBER 180/830 computer under NOS 2.5 operating system. The main phenomena have been calculated correctly and some conclusions about the 3D characteristics of the condensation due to the spray and its simulation with a 1D tool have been got.« less

Development of the atmospheric correction algorithm for the next generation geostationary ocean color sensor data

NASA Astrophysics Data System (ADS)

Lee, Kwon-Ho; Kim, Wonkook

2017-04-01

The geostationary ocean color imager-II (GOCI-II), designed to be focused on the ocean environmental monitoring with better spatial (250m for local and 1km for full disk) and spectral resolution (13 bands) then the current operational mission of the GOCI-I. GOCI-II will be launched in 2018. This study presents currently developing algorithm for atmospheric correction and retrieval of surface reflectance over land to be optimized with the sensor's characteristics. We first derived the top-of-atmosphere radiances as the proxy data derived from the parameterized radiative transfer code in the 13 bands of GOCI-II. Based on the proxy data, the algorithm has been made with cloud masking, gas absorption correction, aerosol inversion, computation of aerosol extinction correction. The retrieved surface reflectances are evaluated by the MODIS level 2 surface reflectance products (MOD09). For the initial test period, the algorithm gave error of within 0.05 compared to MOD09. Further work will be progressed to fully implement the GOCI-II Ground Segment system (G2GS) algorithm development environment. These atmospherically corrected surface reflectance product will be the standard GOCI-II product after launch.

High-performance finite-difference time-domain simulations of C-Mod and ITER RF antennas

NASA Astrophysics Data System (ADS)

Jenkins, Thomas G.; Smithe, David N.

2015-12-01

Finite-difference time-domain methods have, in recent years, developed powerful capabilities for modeling realistic ICRF behavior in fusion plasmas [1, 2, 3, 4]. When coupled with the power of modern high-performance computing platforms, such techniques allow the behavior of antenna near and far fields, and the flow of RF power, to be studied in realistic experimental scenarios at previously inaccessible levels of resolution. In this talk, we present results and 3D animations from high-performance FDTD simulations on the Titan Cray XK7 supercomputer, modeling both Alcator C-Mod's field-aligned ICRF antenna and the ITER antenna module. Much of this work focuses on scans over edge density, and tailored edge density profiles, to study dispersion and the physics of slow wave excitation in the immediate vicinity of the antenna hardware and SOL. An understanding of the role of the lower-hybrid resonance in low-density scenarios is emerging, and possible implications of this for the NSTX launcher and power balance are also discussed. In addition, we discuss ongoing work centered on using these simulations to estimate sputtering and impurity production, as driven by the self-consistent sheath potentials at antenna surfaces.

High-Performance Computational Modeling of ICRF Physics and Plasma-Surface Interactions in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Jenkins, Thomas; Smithe, David

2016-10-01

Inefficiencies and detrimental physical effects may arise in conjunction with ICRF heating of tokamak plasmas. Large wall potential drops, associated with sheath formation near plasma-facing antenna hardware, give rise to high-Z impurity sputtering from plasma-facing components and subsequent radiative cooling. Linear and nonlinear wave excitations in the plasma edge/SOL also dissipate injected RF power and reduce overall antenna efficiency. Recent advances in finite-difference time-domain (FDTD) modeling techniques allow the physics of localized sheath potentials, and associated sputtering events, to be modeled concurrently with the physics of antenna near- and far-field behavior and RF power flow. The new methods enable time-domain modeling of plasma-surface interactions and ICRF physics in realistic experimental configurations at unprecedented spatial resolution. We present results/animations from high-performance (10k-100k core) FDTD/PIC simulations spanning half of Alcator C-Mod at mm-scale resolution, exploring impurity production due to localized sputtering (in response to self-consistent sheath potentials at antenna surfaces) and the physics of parasitic slow wave excitation near the antenna hardware and SOL. Supported by US DoE (Award DE-SC0009501) and the ALCC program.

40 CFR 85.2115 - Notification of intent to certify.

Code of Federal Regulations, 2013 CFR

2013-07-01

... testing and durability demonstration represent worst case with respect to emissions of all those... submitted by the aftermarket manufacturer to: Mod Director, MOD (EN-340F), Attention: Aftermarket Parts, 401...

40 CFR 85.2115 - Notification of intent to certify.

Code of Federal Regulations, 2012 CFR

2012-07-01

... testing and durability demonstration represent worst case with respect to emissions of all those... submitted by the aftermarket manufacturer to: Mod Director, MOD (EN-340F), Attention: Aftermarket Parts, 401...

40 CFR 85.2115 - Notification of intent to certify.

Code of Federal Regulations, 2014 CFR

2014-07-01

... testing and durability demonstration represent worst case with respect to emissions of all those... submitted by the aftermarket manufacturer to: Mod Director, MOD (EN-340F), Attention: Aftermarket Parts, 401...

Experiment data report for Semiscale Mod-1 Test S-05-1 (alternate ECC injection test)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, E. M.; Patton, Jr., M. L.; Sackett, K. E.

Recorded test data are presented for Test S-05-1 of the Semiscale Mod-1 alternate ECC injection test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-05-1 was conducted from initial conditions of 2263 psia and 544/sup 0/F to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the cold leg broken loop piping. During the test, cooling water was injected into the vessel lower plenum to simulatemore » emergency core coolant injection in a PWR, with the flow rate based on system volume scaling.« less

Mod II engine performance

NASA Technical Reports Server (NTRS)

Richey, Albert E.; Huang, Shyan-Cherng

1987-01-01

The testing of a prototype of an automotive Stirling engine, the Mod II, is discussed. The Mod II is a one-piece cast block with a V-4 single-crankshaft configuration and an annular regenerator/cooler design. The initial testing of Mod II concentrated on the basic engine, with auxiliaries driven by power sources external to the engine. The performance of the engine was tested at 720 C set temperature and 820 C tube temperature. At 720 C, it is observed that the power deficiency is speed dependent and linear, with a weak pressure dependency, and at 820 C, the power deficiency is speed and pressure dependent. The effects of buoyancy and nozzle spray pattern on the heater temperature spread are investigated. The characterization of the oil pump and the operating cycle and temperature spread tests are proposed for further evaluation of the engine.

Deciphering Suicide and Other Manners of Death Associated with Drug Intoxication: A Centers for Disease Control and Prevention Consultation Meeting Summary.

PubMed

Stone, Deborah M; Holland, Kristin M; Bartholow, Brad; E Logan, Joseph; LiKamWa McIntosh, Wendy; Trudeau, Aimee; Rockett, Ian R H

2017-08-01

Manner of death (MOD) classification (i.e., natural, accident, suicide, homicide, or undetermined cause) affects mortality surveillance and public health research, policy, and practice. Determination of MOD in deaths caused by drug intoxication is challenging, with marked variability across states. The Centers for Disease Control and Prevention hosted a multidisciplinary meeting to discuss drug intoxication deaths as they relate to suicide and other MOD. The meeting objectives were to identify individual-level, system-level, and place-based factors affecting MOD classification and identify potential solutions to classification barriers. Suggested strategies included improved standardization in death scene investigation, toxicology, and autopsy practice; greater accountability; and creation of job aids for investigators. Continued collaboration and coordination of activities are needed among stakeholders to affect prevention efforts.

Removal of phosphate from eutrophic lakes through adsorption by in situ formation of magnesium hydroxide from diatomite.

PubMed

Xie, Fazhi; Wu, Fengchang; Liu, Guijian; Mu, Yunsong; Feng, Chenglian; Wang, Huanhua; Giesy, John P

2014-01-01

Since in situ formation of Mg(OH)2 can efficiently sorb phosphate (PO4) from low concentrations in the environment, a novel dispersed magnesium oxide nanoflake-modified diatomite adsorbent (MOD) was developed for use in restoration of eutrophic lakes by removal of excess PO4. Various adsorption conditions, such as pH, temperature and contact time were investigated. Overall, sorption capacities increased with increasing temperature and contact time, and decreased with increasing pH. Adsorption of PO4 was well described by both the Langmuir isotherm and pseudo second-order models. Theoretical maximum sorption capacity of MOD for PO4 was 44.44-52.08 mg/g at experimental conditions. Characterization of PO4 adsorbed to MOD by use of X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and solid state (31)P nuclear magnetic resonance revealed that electrostatic attraction, surface complexation and chemical conversion in situ were the major forces in adsorption of PO4. Mg(OH)2 formed in situ had a net positive charge on the surface of the MOD that could adsorb PO4(3-) and HPO4(2-) anion to form surface complex and gradually convert to Mg3(PO4)2 and MgHPO4. Efficiency of removal of PO4 was 90% when 300 mg MOD/L was added to eutrophic lake water. Results presented here demonstrated the potential use of the MOD for restoration of eutrophic lakes by removal of excess PO4.

Pretest analysis of Semiscale Mod-3 baseline test S-07-8 and S-07-9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fineman, C.P.; Steiner, J.L.; Snider, D.M.

This document contains a pretest analysis of the Semiscale Mod-3 system thermal-hydraulic response for the second and third integral tests in Test Series 7 (Tests S-07-8 and S-07-9). Test Series 7 is the first test series to be conducted with the Semiscale Mod-3 system. The design of the Mod-3 system includes an improved representation of certain portions of a pressurized water reactor (PWR) when compared to the previously operated Semiscale Mod-1 system. The improvements include a new vessel which contains a full length (3.66 m) core, a full length upper plenum and upper head, and an external downcomer. An activemore » pump and active steam generator scaled to their pressurized water reactor (PWR) counterparts have been added to the broken loop. The upper head design includes the capability to simulate emergency core coolant (ECC) injection into this region. Test Series 7 is divided into three groups of tests that emphasize the evaluation of the Mod-3 system performance during different phases of the loss-of-coolant experiment (LOCE) transient. The last test group, which includes Tests S-07-8 and S-07-9, will be used to evaluate the integral behavior of the system. The previous two test groups were used to evaluate the blowdown behavior and the reflood behavior of the system. 3 refs., 35 figs., 12 tabs.« less

Forest fire danger index based on modifying Nesterov Index, fuel, and anthropogenic activities using MODIS TERRA, AQUA and TRMM satellite datasets

NASA Astrophysics Data System (ADS)

Suresh Babu, K. V.; Roy, Arijit; Ramachandra Prasad, P.

2016-05-01

Forest fire has been regarded as one of the major causes of degradation of Himalayan forests in Uttarakhand. Forest fires occur annually in more than 50% of forests in Uttarakhand state, mostly due to anthropogenic activities and spreads due to moisture conditions and type of forest fuels. Empirical drought indices such as Keetch-Byram drought index, the Nesterov index, Modified Nesterov index, the Zhdanko index which belongs to the cumulative type and the Angstrom Index which belongs to the daily type have been used throughout the world to assess the potential fire danger. In this study, the forest fire danger index has been developed from slightly modified Nesterov index, fuel and anthropogenic activities. Datasets such as MODIS TERRA Land Surface Temperature and emissivity (MOD11A1), MODIS AQUA Atmospheric profile product (MYD07) have been used to determine the dew point temperature and land surface temperature. Precipitation coefficient has been computed from Tropical Rainfall measuring Mission (TRMM) product (3B42RT). Nesterov index has been slightly modified according to the Indian context and computed using land surface temperature, dew point temperature and precipitation coefficient. Fuel type danger index has been derived from forest type map of ISRO based on historical fire location information and disturbance danger index has been derived from disturbance map of ISRO. Finally, forest fire danger index has been developed from the above mentioned indices and MODIS Thermal anomaly product (MOD14) has been used for validating the forest fire danger index.

The NASA/MSFC global reference atmospheric model: MOD 3 (with spherical harmonic wind model)

NASA Technical Reports Server (NTRS)

Justus, C. G.; Fletcher, G. R.; Gramling, F. E.; Pace, W. B.

1980-01-01

Improvements to the global reference atmospheric model are described. The basic model includes monthly mean values of pressure, density, temperature, and geostrophic winds, as well as quasi-biennial and small and large scale random perturbations. A spherical harmonic wind model for the 25 to 90 km height range is included. Below 25 km and above 90 km, the GRAM program uses the geostrophic wind equations and pressure data to compute the mean wind. In the altitudes where the geostrophic wind relations are used, an interpolation scheme is employed for estimating winds at low latitudes where the geostrophic wind relations being to mesh down. Several sample wind profiles are given, as computed by the spherical harmonic model. User and programmer manuals are presented.

Mordell integrals and Giveon-Kutasov duality

NASA Astrophysics Data System (ADS)

Giasemidis, Georgios; Tierz, Miguel

2016-01-01

We solve, for finite N, the matrix model of supersymmetric U( N) Chern-Simons theory coupled to N f massive hypermultiplets of R-charge 1/2 , together with a Fayet-Iliopoulos term. We compute the partition function by identifying it with a determinant of a Hankel matrix, whose entries are parametric derivatives (of order N f - 1) of Mordell integrals. We obtain finite Gauss sums expressions for the partition functions. We also apply these results to obtain an exhaustive test of Giveon-Kutasov (GK) duality in the N=3 setting, by systematic computation of the matrix models involved. The phase factor that arises in the duality is then obtained explicitly. We give an expression characterized by modular arithmetic (mod 4) behavior that holds for all tested values of the parameters (checked up to N f = 12 flavours).

WEST-3 wind turbine simulator development. Volume 2: Verification

NASA Technical Reports Server (NTRS)

Sridhar, S.

1985-01-01

The details of a study to validate WEST-3, a new time wind turbine simulator developed by Paragib Pacific Inc., are presented in this report. For the validation, the MOD-0 wind turbine was simulated on WEST-3. The simulation results were compared with those obtained from previous MOD-0 simulations, and with test data measured during MOD-0 operations. The study was successful in achieving the major objective of proving that WEST-3 yields results which can be used to support a wind turbine development process. The blade bending moments, peak and cyclic, from the WEST-3 simulation correlated reasonably well with the available MOD-0 data. The simulation was also able to predict the resonance phenomena observed during MOD-0 operations. Also presented in the report is a description and solution of a serious numerical instability problem encountered during the study. The problem was caused by the coupling of the rotor and the power train models. The results of the study indicate that some parts of the existing WEST-3 simulation model may have to be refined for future work; specifically, the aerodynamics and procedure used to couple the rotor model with the tower and the power train models.

A robust and accurate center-frequency estimation (RACE) algorithm for improving motion estimation performance of SinMod on tagged cardiac MR images without known tagging parameters.

PubMed

Liu, Hong; Wang, Jie; Xu, Xiangyang; Song, Enmin; Wang, Qian; Jin, Renchao; Hung, Chih-Cheng; Fei, Baowei

2014-11-01

A robust and accurate center-frequency (CF) estimation (RACE) algorithm for improving the performance of the local sine-wave modeling (SinMod) method, which is a good motion estimation method for tagged cardiac magnetic resonance (MR) images, is proposed in this study. The RACE algorithm can automatically, effectively and efficiently produce a very appropriate CF estimate for the SinMod method, under the circumstance that the specified tagging parameters are unknown, on account of the following two key techniques: (1) the well-known mean-shift algorithm, which can provide accurate and rapid CF estimation; and (2) an original two-direction-combination strategy, which can further enhance the accuracy and robustness of CF estimation. Some other available CF estimation algorithms are brought out for comparison. Several validation approaches that can work on the real data without ground truths are specially designed. Experimental results on human body in vivo cardiac data demonstrate the significance of accurate CF estimation for SinMod, and validate the effectiveness of RACE in facilitating the motion estimation performance of SinMod. Copyright © 2014 Elsevier Inc. All rights reserved.

MODi: a powerful and convenient web server for identifying multiple post-translational peptide modifications from tandem mass spectra.

PubMed

Kim, Sangtae; Na, Seungjin; Sim, Ji Woong; Park, Heejin; Jeong, Jaeho; Kim, Hokeun; Seo, Younghwan; Seo, Jawon; Lee, Kong-Joo; Paek, Eunok

2006-07-01

MOD(i) (http://modi.uos.ac.kr/modi/) is a powerful and convenient web service that facilitates the interpretation of tandem mass spectra for identifying post-translational modifications (PTMs) in a peptide. It is powerful in that it can interpret a tandem mass spectrum even when hundreds of modification types are considered and the number of potential PTMs in a peptide is large, in contrast to most of the methods currently available for spectra interpretation that limit the number of PTM sites and types being used for PTM analysis. For example, using MOD(i), one can consider for analysis both the entire PTM list published on the unimod webpage (http://www.unimod.org) and user-defined PTMs simultaneously, and one can also identify multiple PTM sites in a spectrum. MOD(i) is convenient in that it can take various input file formats such as .mzXML, .dta, .pkl and .mgf files, and it is equipped with a graphical tool called MassPective developed to display MOD(i)'s output in a user-friendly manner and helps users understand MOD(i)'s output quickly. In addition, one can perform manual de novo sequencing using MassPective.

mod_bio: Apache modules for Next-Generation sequencing data.

PubMed

Lindenbaum, Pierre; Redon, Richard

2015-01-01

We describe mod_bio, a set of modules for the Apache HTTP server that allows the users to access and query fastq, tabix, fasta and bam files through a Web browser. Those data are made available in plain text, HTML, XML, JSON and JSON-P. A javascript-based genome browser using the JSON-P communication technique is provided as an example of cross-domain Web service. https://github.com/lindenb/mod_bio. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Use of blade pitch control to provide power train damping for the Mod-2, 2.5-mW wind turbine

NASA Technical Reports Server (NTRS)

Blissell, W. A., Jr.

1995-01-01

The Control System for the Mod-2 wind turbine system is required to provide not only for startup, RPM regulation, maximizing or regulating power, and stopping the rotor, but also for load limiting, especially in the power train. Early operations with above-rated winds revealed an instability which was caused primarily by coupling between the quill shaft and the rotor air loads. This instability caused the first of several major Mod-2 Control System changes which are reviewed in the paper.

Harpoon Employment in Naval Antisurface Warfare (ASUW)

DTIC Science & Technology

1988-04-01

7 KASHIN MOD ...... 6 KILDEN MOD ...... 3 UDALOY .......... 8 KASHIN ......... 13 KANIN ........... 6 KOTLIN .......... 6 SKORY ........... 5 KILDIN...1 SVERDLOV CLCP 17,200 1 SVERDLOV CCL 17,200 DESTROYER I SOVREMENNY DDG 7,850 1 UDALOY DDG 8,300 4 KASHIN DDG 4,900 3 KANIN DDG 4,.150 2 SAM- KOTLIN ...DDG 3,850 4 MOD- KOTLIN DDG 3,750 FRIGATES 2 KRIVAK 3 FFG 3,800 5 KRIVAK 2 FFG 3,800 6 KRIVAK I FFG 3,800 SUBMARINE FORCES 26 SSGN/SSG 50 SSN/SS Source

Mod-5A wind turbine generator program design report. Volume 4: Drawings and specifications, book 1

NASA Astrophysics Data System (ADS)

1984-08-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. Volume 4 contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. This is the first of five books of volume four. It contains structural design criteria, generator step-up transformer specs, specs for design, fabrication and testing of the system, specs for the ground control enclosure, systems specs, slip ring specs, and control system specs.

Mod-5A Wind Turbine Generator Program Design Report. Volume 4: Drawings and Specifications, Book 1

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. Volume 4 contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. This is the first of five books of volume four. It contains structural design criteria, generator step-up transformer specs, specs for design, fabrication and testing of the system, specs for the ground control enclosure, systems specs, slip ring specs, and control system specs.

Integrating Occupational Characteristics into Human Performance Models: IPME Versus ISMAT Approach

DTIC Science & Technology

2009-08-01

modélisation générique de la performance humaine appelé Integrated Performance Modelling Environment (IPME). Ce projet a permis d’explorer l’utilisation de la...groupes professionnels dans des modèles de performance humaine : l’approche IPME et l’approche ISMAT Par Christy Lorenzen; RDDC RC 2009-059; R & D...application de simulation d’événements discrets disponible sur le marché et servant à développer des modèles qui simulent la performance humaine et de

An Introduction to the IP/PCT Model Implementation in IPME

DTIC Science & Technology

2011-03-01

perceptuel (TCP) mis en œuvre dans le logiciel Environnement intégré de modélisation des performances (EIMP) par Micro Analysis and Design. Ce...de la théorie du contrôle perceptuel (TCP) mis en œuvre dans le logiciel Environnement intégré de modélisation des performances (EIMP) par Micro...modèles de traitement de l’information (TI) et de la théorie du contrôle perceptuel (TCP) mis en œuvre dans le logiciel Environnement intégré de

Economic Analysis Model Evaluation for Technology Modernization Programs.

DTIC Science & Technology

1983-09-01

program and ’ expost - facto ’ utilized the ASD model to evaluate the accuracy of the ASD model. The following chapter reviews the literature on Tech Mod and...was applied to the CAR 80 Tech Mod project ’ expost - facto ’ in order to develop an ASD model estimated rate o . return. The ASD model was applied in...ASD estimate to achieve a range for the actual IRR. The ASD model was applied expost - facto to the CAR 80 Tech Mod program to derive an IRR. Initial data

Consistency of two global MODIS aerosol products over ocean on Terra and Aqua CERES SSF datasets

NASA Astrophysics Data System (ADS)

Ignatov, Alexander; Minnis, Patrick; Wielicki, Bruce; Loeb, Norman G.; Remer, Lorraine A.; Kaufman, Yoram J.; Miller, Walter F.; Sun-Mack, Sunny; Laszlo, Istvan; Geier, Erika B.

2004-12-01

MODIS aerosol retrievals over ocean from Terra and Aqua platforms are available from the Clouds and the Earth's Radiant Energy System (CERES) Single Scanner Footprint (SSF) datasets generated at NASA Langley Research Center (LaRC). Two aerosol products are reported side by side. The primary M product is generated by subsetting and remapping the multi-spectral (0.44 - 2.1 μm) MOD04 aerosols onto CERES footprints. MOD04 processing uses cloud screening and aerosol algorithms developed by the MODIS science team. The secondary (AVHRR-like) A product is generated in only two MODIS bands: 1 and 6 on Terra, and ` and 7 on Aqua. The A processing uses NASA/LaRC cloud-screening and NOAA/NESDIS single channel aerosol algorthm. The M and A products have been documented elsewhere and preliminarily compared using two weeks of global Terra CERES SSF (Edition 1A) data in December 2000 and June 2001. In this study, the M and A aerosol optical depths (AOD) in MODIS band 1 and (0.64 μm), τ1M and τ1A, are further checked for cross-platform consistency using 9 days of global Terra CERES SSF (Edition 2A) and Aqua CERES SSF (Edition 1A) data from 13 - 21 October 2002.

modPDZpep: a web resource for structure based analysis of human PDZ-mediated interaction networks.

PubMed

Sain, Neetu; Mohanty, Debasisa

2016-09-21

PDZ domains recognize short sequence stretches usually present in C-terminal of their interaction partners. Because of the involvement of PDZ domains in many important biological processes, several attempts have been made for developing bioinformatics tools for genome-wide identification of PDZ interaction networks. Currently available tools for prediction of interaction partners of PDZ domains utilize machine learning approach. Since, they have been trained using experimental substrate specificity data for specific PDZ families, their applicability is limited to PDZ families closely related to the training set. These tools also do not allow analysis of PDZ-peptide interaction interfaces. We have used a structure based approach to develop modPDZpep, a program to predict the interaction partners of human PDZ domains and analyze structural details of PDZ interaction interfaces. modPDZpep predicts interaction partners by using structural models of PDZ-peptide complexes and evaluating binding energy scores using residue based statistical pair potentials. Since, it does not require training using experimental data on peptide binding affinity, it can predict substrates for diverse PDZ families. Because of the use of simple scoring function for binding energy, it is also fast enough for genome scale structure based analysis of PDZ interaction networks. Benchmarking using artificial as well as real negative datasets indicates good predictive power with ROC-AUC values in the range of 0.7 to 0.9 for a large number of human PDZ domains. Another novel feature of modPDZpep is its ability to map novel PDZ mediated interactions in human protein-protein interaction networks, either by utilizing available experimental phage display data or by structure based predictions. In summary, we have developed modPDZpep, a web-server for structure based analysis of human PDZ domains. It is freely available at http://www.nii.ac.in/modPDZpep.html or http://202.54.226.235/modPDZpep.html . This article was reviewed by Michael Gromiha and Zoltán Gáspári.

Chemical composition of groundwater/drinking water and oncological disease mortality in Slovak Republic.

PubMed

Rapant, S; Cvečková, V; Fajčíková, K; Dietzová, Z; Stehlíková, B

2017-02-01

This study deals with the analysis of relationship between chemical composition of the groundwater/drinking water and the data on mortality from oncological diseases (MOD) in the Slovak Republic. Primary data consist of the Slovak national database of groundwater analyses (20,339 chemical analyses, 34 chemical elements/compounds) and data on MOD (17 health indicators) collected for the 10-year period (1994-2003). The chemical and health data were unified in the same form and expressed as the mean values for each of 2883 municipalities within the Slovak Republic. Pearson and Spearman correlation as well as artificial neural network (ANN) methods were used for analysis of the relationship between chemical composition of groundwater/drinking water and MOD. The most significant chemical elements having influence on MOD were identified together with their limit values (limit and optimal contents). Based on the results of calculations, made through the neural networks, the following eight chemical elements/parameters in the groundwater were defined as the most significant for MOD: Ca + Mg (mmol l -1 ), Ca, Mg, TDS, Cl, HCO 3 , SO 4 and NO 3 . The results document the highest relationship between MOD and groundwater contents of Ca + Mg (mmol l -1 ), Ca and Mg. We observe increased MOD with low (deficit) contents of these three parameters of groundwater/drinking water. The following limit values were set for the most significant groundwater chemicals/parameters: Ca + Mg 1.73-5.85 mmol l -1 , Ca 60.5-196.8 mg l -1 and Mg 25.6-35.8 mg l -1 . At these concentration ranges, the mortality for oncological diseases in the Slovak Republic is at the lowest levels. These limit values are about twice higher in comparison with the current Slovak valid guideline values for the drinking water.

Control of artificial pinning centers in REBCO coated conductors derived from the trifluoroacetate metal-organic deposition process

NASA Astrophysics Data System (ADS)

Izumi, T.; Nakaoka, K.

2018-07-01

The metal-organic deposition (MOD) process using metal trifluoroacetate salts (TFA) has the advantages of low-cost and high-scalability for the fabrication of REBa2Cu3O y (REBCO, RE: rare earth elements) superconducting coated conductors (CCs) with high critical current density, in principle, because of its non-vacuum process. For the magnetic applications of CCs such as motors, magnetic resonance imaging and superconducting magnetic energy storage, further improvement of superconducting performance under magnetic fields is required. However, the in-field superconducting performance of REBCO CCs derived from the TFA-MOD process had been inferior to those derived from the vapor-phase process. In order to improve the in-field performance, the size control of the artificial pinning centers has been known as an effective way. In the early stage, the BaZrO3 (BZO) material, which was one of the effective materials in the CCs by the vapor-phase process, was also introduced in the TFA-MOD-derived CCs. The unique feature of the BZO material in the TFA-MOD process is the shape. The BZO in the TFA-MOD process formed the particle shape, although in the vapor-phase process it has a rod shape with a long axis elongating along the thickness direction. In addition, a special heat treatment for refining the BZO particles was developed, which is called the ‘interim heat treatment’. This heating profile made the in-field characteristics higher, although they were still lower than those of the vapor-phase process. Then, the new MOD process including ‘ultra-thin once coating’ was recently developed for further refinement of the BZO particles. The characteristics of the new TFA-MOD-derived CCs in magnetic fields have become compatible with those of the CCs derived from the vapor-phase process.

Comparison of biophysical factors influencing on emphysema quantification with low-dose CT

NASA Astrophysics Data System (ADS)

Heo, Chang Yong; Kim, Jong Hyo

2014-03-01

Emphysema Index(EI) measurements in MDCT is known to be influenced by various biophysical factors such as total lung volume, and body size. We investigated the association of the four biophysical factors with emphysema index in low-dose MDCT. In particular, we attempted to identify a potentially stronger biophysical factor than total lung volume. A total of 400 low-dose MDCT volumes taken at 120kVp, 40mAs, 1mm thickness, and B30f reconstruction kernel were used. The lungs, airways, and pulmonary vessels were automatically segmented, and two Emphysema Indices, relative area below -950HU(RA950) and 15th percentile(Perc15), were extracted from the segmented lungs. The biophysical factors such as total lung volume(TLV), mode of lung attenuation(ModLA), effective body diameter(EBD), and the water equivalent body diameter(WBD) were estimated from the segmented lung and body area. The association of biophysical factors with emphysema indices were evaluated by correlation coefficients. The mean emphysema indices were 8.3±5.5(%) in RA950, and -930±18(HU) in Perc15. The estimates of biophysical factors were 4.7±1.0(L) in TLV, -901±21(HU) in ModLA, 26.9±2.2(cm) in EBD, and 25.9±2.6(cm) in WBD. The correlation coefficients of biophysical factors with RA950 were 0.73 in TLV, 0.94 in ModLA, 0.31 in EBD, and 0.18 WBD, the ones with Perc15 were 0.74 in TLV, 0.98 in ModLA, 0.29 in EBD, and 0.15 WBD. Study results revealed that two biophysical factors, TLV and ModLA, mostly affects the emphysema indices. In particular, the ModLA exhibited strongest correlation of 0.98 with Perc15, which indicating the ModLA is the most significant confounding biophysical factor in emphysema indices measurement.

The modA10 phasevarion of nontypeable Haemophilus influenzae R2866 regulates multiple virulence-associated traits.

PubMed

VanWagoner, Timothy M; Atack, John M; Nelson, Kevin L; Smith, Hannah K; Fox, Kate L; Jennings, Michael P; Stull, Terrence L; Smith, Arnold L

2016-03-01

Non-typeable Haemophilus influenzae (NTHi) is a human restricted commensal and pathogen that elicits inflammation by adhering to and invading airway epithelia cells: transcytosis across these cells can result in systemic infection. NTHi strain R2866 was isolated from the blood of a normal 30-month old infant with meningitis, and is unusual for NTHi in that it is able to cause systemic infection. Strain R2866 is able to replicate in normal human serum due to expression of lgtC which mimics human blood group p(k). R2866 contains a phase-variable DNA methyltransferase, modA10 which switches ON and OFF randomly and reversibly due to polymerase slippage over a long tetrameric repeat tract located in its open reading frame. Random gain or loss of repeats during replication can results in expressed (ON), or not expressed (OFF) states, the latter due to a frameshift or transcriptional termination at a premature stop codon. We sought to determine if the unusual virulence of R2866 was modified by modA10 phase-variation. A modA10 knockout mutant was found to have increased adherence to, and invasion of, human ear and airway monolayers in culture, and increased invasion and transcytosis of polarized human bronchial epithelial cells. Intriguingly, the rate of bacteremia was lower in the infant rat model of infection than a wild-type R2866 strain, but the fatality rate was greater. Transcriptional analysis comparing the modA10 knockout to the R2866 wild-type parent strain showed increased expression of genes in the modA10 knockout whose products mediate cellular adherence. We conclude that loss of ModA10 function in strain R2866 enhances colonization and invasion by increasing expression of genes that allow for increased adherence, which can contribute to the increased virulence of this strain. Copyright © 2015 Elsevier Ltd. All rights reserved.

Operating experience with four 200 kW Mod-0A wind turbine generators

NASA Technical Reports Server (NTRS)

Birchenough, A. G.; Saunders, A. L.; Nyland, T. W.; Shaltens, R. K.

1982-01-01

The windpowered generator, Mod-0A, and its advantages and disadvantages, particularly as it affects reliability, are discussed. The machine performance with regard to power availability and power output is discussed.

40 CFR 85.2115 - Notification of intent to certify.

Code of Federal Regulations, 2010 CFR

2010-07-01

... which the part is being certified including make(s), model(s), year(s), engine size(s) and all other... submitted by the aftermarket manufacturer to: Mod Director, MOD (EN-340F), Attention: Aftermarket Parts, 401...

Initial utility experience with cluster of three Mod-2 wind turbine systems

NASA Technical Reports Server (NTRS)

Seely, D. B.; Warchol, E. J.; Butler, N. G.; Ciranny, S.

1982-01-01

This paper describes the initial utility experiences of operating three MOD-2s during the Engineering Acceptance Testing. Electrical quantities of bus voltage, phase currents and power are initially being recorded to evaluate impacts to customers on the 69-kV subtransmission line during synchronization and operation of one or more WTSs. To date, effects on the system have been essentially undetectable. Measurements of television signal strengths were taken at an existing television remote pickup and relay station at the WTS site. Potential TV signal interference problems from the WTSs have been avoided by replacing the remote pickups with microwave repeater links for the four TV channels received from Portland, Oregon. Preliminary measurements of audible and sub-audible noise levels indicate that the upwind rotor, tubular tower design of the MOD-2 does not have the pulsing high intensity infrasound problems experienced by the MOD-1 machine at Boone, North Carolina.

Mentoring SFRM: A New Approach to International Space Station Flight Control Training

NASA Technical Reports Server (NTRS)

Huning, Therese; Barshi, Immanuel; Schmidt, Lacey

2009-01-01

The Mission Operations Directorate (MOD) of the Johnson Space Center is responsible for providing continuous operations support for the International Space Station (ISS). Operations support requires flight controllers who are skilled in team performance as well as the technical operations of the ISS. Space Flight Resource Management (SFRM), a NASA adapted variant of Crew Resource Management (CRM), is the competency model used in the MOD. ISS flight controller certification has evolved to include a balanced focus on development of SFRM and technical expertise. The latest challenge the MOD faces is how to certify an ISS flight controller (Operator) to a basic level of effectiveness in 1 year. SFRM training uses a twopronged approach to expediting operator certification: 1) imbed SFRM skills training into all Operator technical training and 2) use senior flight controllers as mentors. This paper focuses on how the MOD uses senior flight controllers as mentors to train SFRM skills.

Wind - Prototypes on the landscape

NASA Astrophysics Data System (ADS)

Smith, M. L.

1981-12-01

Large wind turbines are shown to be attractive to utilities because of the potential for decreasing gas and oil consumption, the relatively low costs for entry into the field, and the wide distribution of wind energy. The total generating capacity can be increased in incremental steps, experience in construction and operation of large turbines have been gained from the NASA Mod O, OA, 1, and 2 models, and advances in manufacturing processes will make the large turbines competitive as replacement power for oil and gas burning utility generators. The 300 ft rotor Mod 2 machines are described, along with designs for the Mod 5A and Mod 5B wind turbines, with 400 and 422 ft, 6.2 and 7.2 MW rotors and outputs, respectively. Current plans for multi-MW windfarms are reviewed, and the option of using the land around large wind turbines for other purposes is stressed.

Mission Operations Directorate - Success Legacy of the Space Shuttle Program

NASA Technical Reports Server (NTRS)

Azbell, Jim

2010-01-01

In support of the Space Shuttle Program, as well as NASA's other human space flight programs, the Mission Operations Directorate (MOD) at the Johnson Space Center has become the world leader in human spaceflight operations. From the earliest programs - Mercury, Gemini, Apollo - through Skylab, Shuttle, ISS, and our Exploration initiatives, MOD and its predecessors have pioneered ops concepts and emphasized a history of mission leadership which has added value, maximized mission success, and built on continual improvement of the capabilities to become more efficient and effective. MOD's focus on building and contributing value with diverse teams has been key to their successes both with the US space industry and the broader international community. Since their beginning, MOD has consistently demonstrated their ability to evolve and respond to an ever changing environment, effectively prepare for the expected and successfully respond to the unexpected, and develop leaders, expertise, and a culture that has led to mission and Program success.

Development of Low-Cost Inverted Microscope to Detect Early Growth of Mycobacterium tuberculosis in MODS Culture

PubMed Central

Zimic, Mirko; Velazco, Abner; Comina, Germán; Coronel, Jorge; Fuentes, Patricia; Luna, Carmen G.; Sheen, Patricia; Gilman, Robert H.; Moore, David A. J.

2010-01-01

Background The microscopic observation drug susceptibility (MODS) assay for rapid, low-cost detection of tuberculosis and multidrug resistant tuberculosis depends upon visualization of the characteristic cording colonies of Mycobacterium tuberculosis in liquid media. This has conventionally required an inverted light microscope in order to inspect the MODS culture plates from below. Few tuberculosis laboratories have this item and the capital cost of $5,000 for a high-end microscope could be a significant obstacle to MODS roll-out. Methodology We hypothesized that the precise definition provided by costly high-specification inverted light microscopes might not be necessary for pattern recognition. Significance In this work we describe the development of a low-cost artesenal inverted microscope that can operate in both a standard or digital mode to effectively replace the expensive commercial inverted light microscope, and an integrated system that could permit a local and remote diagnosis of tuberculosis. PMID:20351778

Analyses of 1/15 scale Creare bypass transient experiments. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kmetyk, L.N.; Buxton, L.D.; Cole, R.K. Jr.

1982-09-01

RELAP4 analyses of several 1/15 scale Creare H-series bypass transient experiments have been done to investigate the effect of using different downcomer nodalizations, physical scales, slip models, and vapor fraction donoring methods. Most of the analyses were thermal equilibrium calculations performed with RELAP4/MOD5, but a few such calculations were done with RELAP4/MOD6 and RELAP4/MOD7, which contain improved slip models. In order to estimate the importance of nonequilibrium effects, additional analyses were performed with TRAC-PD2, RELAP5 and the nonequilibrium option of RELAP4/MOD7. The purpose of these studies was to determine whether results from Westinghouse's calculation of the Creare experiments, which weremore » done with a UHI-modified version of SATAN, were sufficient to guarantee SATAN would be conservative with respect to ECC bypass in full-scale plant analyses.« less

The NASA-LeRC wind turbine sound prediction code

NASA Technical Reports Server (NTRS)

Viterna, L. A.

1981-01-01

Since regular operation of the DOE/NASA MOD-1 wind turbine began in October 1979 about 10 nearby households have complained of noise from the machine. Development of the NASA-LeRC with turbine sound prediction code began in May 1980 as part of an effort to understand and reduce the noise generated by MOD-1. Tone sound levels predicted with this code are in generally good agreement with measured data taken in the vicinity MOD-1 wind turbine (less than 2 rotor diameters). Comparison in the far field indicates that propagation effects due to terrain and atmospheric conditions may be amplifying the actual sound levels by about 6 dB. Parametric analysis using the code has shown that the predominant contributions to MOD-1 rotor noise are: (1) the velocity deficit in the wake of the support tower; (2) the high rotor speed; and (3) off column operation.

Lithium wall conditioning by high frequency pellet injection in RFX-mod

NASA Astrophysics Data System (ADS)

Innocente, P.; Mansfield, D. K.; Roquemore, A. L.; Agostini, M.; Barison, S.; Canton, A.; Carraro, L.; Cavazzana, R.; De Masi, G.; Fassina, A.; Fiameni, S.; Grando, L.; Rais, B.; Rossetto, F.; Scarin, P.

2015-08-01

In the RFX-mod reversed field pinch experiment, lithium wall conditioning has been tested with multiple scopes: to improve density control, to reduce impurities and to increase energy and particle confinement time. Large single lithium pellet injection, lithium capillary-pore system and lithium evaporation has been used for lithiumization. The last two methods, which presently provide the best results in tokamak devices, have limited applicability in the RFX-mod device due to the magnetic field characteristics and geometrical constraints. On the other side, the first mentioned technique did not allow injecting large amount of lithium. To improve the deposition, recently in RFX-mod small lithium multi-pellets injection has been tested. In this paper we compare lithium multi-pellets injection to the other techniques. Multi-pellets gave more uniform Li deposition than evaporator, but provided similar effects on plasma parameters, showing that further optimizations are required.

Factors influencing exemplary science teachers' levels of computer use

NASA Astrophysics Data System (ADS)

Hakverdi, Meral

This study examines exemplary science teachers' use of technology in science instruction, factors influencing their level of computer use, their level of knowledge/skills in using specific computer applications for science instruction, their use of computer-related applications/tools during their instruction, and their students' use of computer applications/tools in or for their science class. After a relevant review of the literature certain variables were selected for analysis. These variables included personal self-efficacy in teaching with computers, outcome expectancy, pupil-control ideology, level of computer use, age, gender, teaching experience, personal computer use, professional computer use and science teachers' level of knowledge/skills in using specific computer applications for science instruction. The sample for this study includes middle and high school science teachers who received the Presidential Award for Excellence in Science Teaching Award (sponsored by the White House and the National Science Foundation) between the years 1997 and 2003 from all 50 states and U.S. territories. Award-winning science teachers were contacted about the survey via e-mail or letter with an enclosed return envelope. Of the 334 award-winning science teachers, usable responses were received from 92 science teachers, which made a response rate of 27.5%. Analysis of the survey responses indicated that exemplary science teachers have a variety of knowledge/skills in using computer related applications/tools. The most commonly used computer applications/tools are information retrieval via the Internet, presentation tools, online communication, digital cameras, and data collection probes. Results of the study revealed that students' use of technology in their science classroom is highly correlated with the frequency of their science teachers' use of computer applications/tools. The results of the multiple regression analysis revealed that personal self-efficacy related to the exemplary science teachers' level of computer use suggesting that computer use is dependent on perceived abilities at using computers. The teachers' use of computer-related applications/tools during class, and their personal self-efficacy, age, and gender are highly related with their level of knowledge/skills in using specific computer applications for science instruction. The teachers' level of knowledge/skills in using specific computer applications for science instruction and gender related to their use of computer-related applications/tools during class and the students' use of computer-related applications/tools in or for their science class. In conclusion, exemplary science teachers need assistance in learning and using computer-related applications/tool in their science class.

Contemporary Patterns of Multiple Organ Dysfunction in Trauma.

PubMed

Shepherd, Joanna M; Cole, Elaine; Brohi, Karim

2017-04-01

Multiple organ dysfunction syndrome (MODS) is associated with poor outcomes for trauma patients. Different forms of MODS may exist and have different consequences. The ability to distinguish them clinically may have implications for prognosis and treatment. We wished to study whether prolonged MODS (PRMODS) could be observed as a distinct clinical entity to early resolving MODS (ERMODS) in critically injured patients. Adult major trauma patients recruited to a prospective observational study at a single major trauma center were eligible for inclusion. MODS was defined as Sequential Organ Failure Assessment (SOFA) score >5; and PRMODS as lasting >7 days. Time to recovery (TTR) was calculated as the number of days before the SOFA fell below the MODS threshold (≤5). Five hundred ninety-five patients were enrolled of whom 285 developed ERMODS (48%) and 184 (31%) PRMODS. Organ dysfunction was more severe and protracted in PRMODS, especially in patients without brain injury (mean SOFA 11 vs. 6, Day 2, P < 0.001; TTR 17 vs. 3 days, P < 0.001). PRMODS exhibited higher rates of hepatic and renal dysfunction (84% vs. 56%; and 78% vs. 47%, P≤0.001). Patterns of recovery were distinct in hepatic, renal, and neurological systems (TTR 15 vs. 4; 20 vs. 3; and 28 vs. 7 days, P < 0.01). PRMODS was associated with higher infection and mortality rates (91% vs. 41%; and 22% vs. 7%, P < 0.001). PRMODS appears common, a distinct clinical entity, and associated with worse patient outcomes. PRMODS may represent an important endpoint for studies evaluating outcomes following trauma.

NetMOD v. 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J

2015-12-22

NetMOD is a tool to model the performance of global ground-based explosion monitoring systems. The version 2.0 of the software supports the simulation of seismic, hydroacoustic, and infrasonic detection capability. The tool provides a user interface to execute simulations based upon a hypothetical definition of the monitoring system configuration, geophysical properties of the Earth, and detection analysis criteria. NetMOD will be distributed with a project file defining the basic performance characteristics of the International Monitoring System (IMS), a network of sensors operated by the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO). Network modeling is needed to be able to assess and explainmore » the potential effect of changes to the IMS, to prioritize station deployment and repair, and to assess the overall CTBTO monitoring capability currently and in the future. Currently the CTBTO uses version 1.0 of NetMOD, provided to them in early 2014. NetMOD will provide a modern tool that will cover all the simulations currently available and allow for the development of additional simulation capabilities of the IMS in the future. NetMOD simulates the performance of monitoring networks by estimating the relative amplitudes of the signal and noise measured at each of the stations within the network based upon known geophysical principles. From these signal and noise estimates, a probability of detection may be determined for each of the stations. The detection probabilities at each of the stations may then be combined to produce an estimate of the detection probability for the entire monitoring network.« less

Scrub Typhus - A Major Cause of Pediatric Intensive Care Admission and Multiple Organ Dysfunction Syndrome: A Single-Center Experience from India.

PubMed

Giri, Prabahs Prasun; Roy, Joydeb; Saha, Agnisekhar

2018-02-01

Scrub typhus has been globally recognized as an emerging infectious disease contributing significantly to pyrexia of unknown origin (PUO) and a potential cause of multiorgan dysfunction syndrome (MODS). We studied the incidence of scrub typhus as a cause of pediatric intensive care unit (PICU) admission and MODS in our hospital and its clinical and laboratory characteristics to measure the incidence of MODS caused by scrub typhus. This study was done in a pediatric teaching hospital in Kolkata, India. Records of patients admitted with PUO from March 2012 to December 2015 were reviewed. Rathi-Goodman-Aghai scoring system was used to identify potential ST patients and confirmed by serological testing. Clinical characteristics, laboratory findings, and treatment response were noted of those needing PICU admissions. Ninety-seven cases of scrub typhus have been identified during that period. PICU admission was needed in 30 of them (31%) which contributed 8.43% of total PICU admissions. Among these 30 patients, 16 (53%) developed MODS which contributed 18.29% of total MODS admitted in PICU. Septic shock was the most common manifestation in as many as 18 (60%) patients followed by encephalopathy in 13 (43%). Patients were treated with either doxycycline alone or in combination with azithromycin. Mean time to complete defervescence was 32 h after first dose of doxycycline. The outcome was excellent without a single mortality. Scrub typhus is an important cause of MODS in this part of the world, especially in fevers associated with features as identified and not responding to conventional antibiotics.

Electrostatic Discharge Issues in International Space Station Program EVAs

NASA Technical Reports Server (NTRS)

Bacon, John B.

2009-01-01

EVA activity in the ISS program encounters several dangerous ESD conditions. The ISS program has been aggressive for many years to find ways to mitigate or to eliminate the associated risks. Investments have included: (1) Major mods to EVA tools, suit connectors & analytical tools (2) Floating Potential Measurement Unit (3) Plasma Contactor Units (4) Certification of new ISS flight attitudes (5) Teraflops of computation (6) Thousands of hours of work by scores of specialists (7) Monthly management attention at the highest program levels. The risks are now mitigated to a level that is orders of magnitude safer than prior operations

Mathematical modeling of solid oxide fuel cells

NASA Technical Reports Server (NTRS)

Lu, Cheng-Yi; Maloney, Thomas M.

1988-01-01

Development of predictive techniques, with regard to cell behavior, under various operating conditions is needed to improve cell performance, increase energy density, reduce manufacturing cost, and to broaden utilization of various fuels. Such technology would be especially beneficial for the solid oxide fuel cells (SOFC) at it early demonstration stage. The development of computer models to calculate the temperature, CD, reactant distributions in the tubular and monolithic SOFCs. Results indicate that problems of nonuniform heat generation and fuel gas depletion in the tubular cell module, and of size limitions in the monolithic (MOD 0) design may be encountered during FC operation.

A comparison of normal versus low dietary carbohydrate intake on substrate oxidation during and after moderate intensity exercise in women.

PubMed

Patterson, Rachel; Potteiger, Jeffrey A

2011-12-01

We compared the effects of consuming a 2-day low-carbohydrate (CHO) diet (low-CHO; 20% CHO, 40% protein, 40% fat) versus an isocaloric 2-day moderate-CHO diet (mod-CHO; 55% CHO, 15% protein, 30% fat) on substrate oxidation during and after exercise in ten active, young women. Subjects were 24.9 ± 6.2% body fat with a VO(2max) of 68.8 ± 13.8 ml/kg FFM/min. For 2 days prior to exercise, subjects consumed either the mod-CHO or the low-CHO diet and then completed treadmill exercise at 55% of VO(2max) until 350 kcal of energy was expended. During exercise and for 2 h post-exercise, expired gases were analyzed to determine oxidation rates for CHO (CHO-OX) and fat (FAT-OX). Significant differences (p < 0.05) were found between diets for CHO-OX and FAT-OX (mg/kg FFM/min) during exercise, 1 h post-ex, and 2 h post-ex. During exercise, FAT-OX was higher (low-CHO 8.7 ± 2.2 vs. mod-CHO 6.2 ± 2.2) and CHO-OX was lower (low-CHO 25.1 ± 5.6 vs. mod-CHO 31.1 ± 6.2) following the low-CHO diet. A similar trend was observed during 1 h post-ex for FAT-OX (low-CHO 2.2 ± 0.5 vs. mod-CHO 1.6 ± 0.5) and CHO-OX (low-CHO 2.5 ± 1.2 vs. mod-CHO 4.1 ± 1.9), as well as 2 h post-ex for FAT-OX (low-CHO vs. 1.9 ± 0.5 mod-CHO 1.7 ± 0.4) and CHO-OX (low-CHO 2.5 ± 0.9 vs. mod-CHO 3.1 ± 1.1). Significant positive correlations were observed between VO(2max) and CHO-OX during exercise and post-exercise, as well as significant negative correlations between VO(2max) and FAT-OX post-exercise in the low-CHO condition. Waist circumference and FAT-OX exhibited a significant negative correlation during exercise in the low-CHO condition. Dietary macronutrient intake influenced substrate oxidation in active young women during and after moderate intensity exercise.

Monocytes, endoplasmic reticulum stress and metabolomics in dogs with multiple organ dysfunction syndrome treated by continuous venovenous hemodiafiltration

PubMed Central

Xu, Yun-Peng; Sui, Xiao-Lu; Zhang, Ai-Sha; Ye, Lei; Gu, Feng-Juan; Chen, Ji-Hong

2017-01-01

Objectives We tried to investigate the mechanism of continuous venovenous hemodiafiltration (CVVHDF) treatment in monocytes function, endoplasmic reticulum (ER) stress signaling pathways, metabolomics and histopathological changes of MODS dogs, and aimed to enhance the understanding of pathogenesis and provide novel avenues to potential therapies. Methods 12 male Beagle dogs were used to develop the stable models of MODS by using hemorrhagic shock plus resuscitation and endotoxemia, and assigned randomly to CVVHDF group (n=6) and MODS group (n=6). The dogs in CVVHDF group were given the typical CVVHDF treatment for 24h after the completion of endotoxin intravenous infusion, while those in MODS group were offered the i.v heparin instead only. Serum sample were collected at five time points, i.e. before anesthesia, 0h, 6h, 12h and 24h after the endotoxin injection (T1˜T5, respectively), and meanwhile, the changes of mRNA, protein and human umbilical vein endothelial cells (HUVECs) apoptosis rates in JNK, CHOP and Caspase-12 were observed before and after interfered by RNA interference technology. Results The levels of DLA-DR, IL-1β and IL-4 were higher than those in MODS group after the CVVHDF treatment, and the early and late apoptosis rates showed downward trend compared with MODS group. In vitro and prior to RNA interference (RNAi), the levels of mRNA and protein expression and HUVECs apoptosis rates of JNK, CHOP and Caspase-12 in CVVHDF group were significantly lower compared to T1 and MODS group respectively. However, the levels of mRNA and protein expression and HUVECs apoptosis rates were significantly lower than those before interfered by RNAi in both two groups. The serum levels of LPCs, ornithine, proline, methionine, etc. were down-regulated while carnitines, FFAs, PC, etc. were increased significantly in MODS (T4), and the serum levels of methionine, proline, arginine and lysine were increased while carnitine, LPCs, PCs, SMs and orthophosporic acid were decreased after 12 hours CVVHDF treatment (T4). Conclusion CVVHDF treatment could reduce the apoptosis of the cells by enhancing the antigen presentation, improving the anti-inflammatory and proinflammatory imbalance and even correcting the metabolic disorder of amino acids and phospholipids. PMID:28380442

Comparison and Evaluation of Annual NDVI Time Series in China Derived from the NOAA AVHRR LTDR and Terra MODIS MOD13C1 Products

PubMed Central

Guo, Xiaoyi; Zhang, Hongyan; Wu, Zhengfang; Zhao, Jianjun; Zhang, Zhengxiang

2017-01-01

Time series of Normalized Difference Vegetation Index (NDVI) derived from multiple satellite sensors are crucial data to study vegetation dynamics. The Land Long Term Data Record Version 4 (LTDR V4) NDVI dataset was recently released at a 0.05 × 0.05° spatial resolution and daily temporal resolution. In this study, annual NDVI time series that are composited by the LTDR V4 and Moderate Resolution Imaging Spectroradiometer (MODIS) NDVI datasets (MOD13C1) are compared and evaluated for the period from 2001 to 2014 in China. The spatial patterns of the NDVI generally match between the LTDR V4 and MOD13C1 datasets. The transitional zone between high and low NDVI values generally matches the boundary of semi-arid and sub-humid regions. A significant and high coefficient of determination is found between the two datasets according to a pixel-based correlation analysis. The spatially averaged NDVI of LTDR V4 is characterized by a much weaker positive regression slope relative to that of the spatially averaged NDVI of the MOD13C1 dataset because of changes in NOAA AVHRR sensors between 2005 and 2006. The measured NDVI values of LTDR V4 were always higher than that of MOD13C1 in western China due to the relatively lower atmospheric water vapor content in western China, and opposite observation appeared in eastern China. In total, 18.54% of the LTDR V4 NDVI pixels exhibit significant trends, whereas 35.79% of the MOD13C1 NDVI pixels show significant trends. Good agreement is observed between the significant trends of the two datasets in the Northeast Plain, Bohai Economic Rim, Loess Plateau, and Yangtze River Delta. By contrast, the datasets contrasted in northwestern desert regions and southern China. A trend analysis of the regression slope values according to the vegetation type shows good agreement between the LTDR V4 and MOD13C1 datasets. This study demonstrates the spatial and temporal consistencies and discrepancies between the AVHRR LTDR and MODIS MOD13C1 NDVI products in China, which could provide useful information for the choice of NDVI products in subsequent studies of vegetation dynamics. PMID:28587266

Comparison and Evaluation of Annual NDVI Time Series in China Derived from the NOAA AVHRR LTDR and Terra MODIS MOD13C1 Products.

PubMed

Guo, Xiaoyi; Zhang, Hongyan; Wu, Zhengfang; Zhao, Jianjun; Zhang, Zhengxiang

2017-06-06

Time series of Normalized Difference Vegetation Index (NDVI) derived from multiple satellite sensors are crucial data to study vegetation dynamics. The Land Long Term Data Record Version 4 (LTDR V4) NDVI dataset was recently released at a 0.05 × 0.05° spatial resolution and daily temporal resolution. In this study, annual NDVI time series that are composited by the LTDR V4 and Moderate Resolution Imaging Spectroradiometer (MODIS) NDVI datasets (MOD13C1) are compared and evaluated for the period from 2001 to 2014 in China. The spatial patterns of the NDVI generally match between the LTDR V4 and MOD13C1 datasets. The transitional zone between high and low NDVI values generally matches the boundary of semi-arid and sub-humid regions. A significant and high coefficient of determination is found between the two datasets according to a pixel-based correlation analysis. The spatially averaged NDVI of LTDR V4 is characterized by a much weaker positive regression slope relative to that of the spatially averaged NDVI of the MOD13C1 dataset because of changes in NOAA AVHRR sensors between 2005 and 2006. The measured NDVI values of LTDR V4 were always higher than that of MOD13C1 in western China due to the relatively lower atmospheric water vapor content in western China, and opposite observation appeared in eastern China. In total, 18.54% of the LTDR V4 NDVI pixels exhibit significant trends, whereas 35.79% of the MOD13C1 NDVI pixels show significant trends. Good agreement is observed between the significant trends of the two datasets in the Northeast Plain, Bohai Economic Rim, Loess Plateau, and Yangtze River Delta. By contrast, the datasets contrasted in northwestern desert regions and southern China. A trend analysis of the regression slope values according to the vegetation type shows good agreement between the LTDR V4 and MOD13C1 datasets. This study demonstrates the spatial and temporal consistencies and discrepancies between the AVHRR LTDR and MODIS MOD13C1 NDVI products in China, which could provide useful information for the choice of NDVI products in subsequent studies of vegetation dynamics.

Lower Hybrid wave edge power loss quantification on the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Faust, I. C.

2015-11-01

For the first time, the power deposition of Lower Hybrid RF waves into the edge plasma of a diverted tokamak has been systematically quantified. Edge deposition represents a parasitic loss of power that can greatly impact the use and efficiency of Lower Hybrid Current Drive (LHCD) at reactor-relevant densities. Through the use of a unique set of fast time resolution edge diagnostics, including innovative fast-thermocouples, an extensive set of Langmuir probes, and a Lyα ionization camera, the toroidal, poloidal and radial structure of the power deposition has been simultaneously determined. Power modulation was used to directly isolate the RF effects due to the prompt (t <τE) response of the scrape-off-layer (SOL) plasma to LHRF power. LHRF power was found to absorb more strongly in the edge at higher densities. It is found that a majority of this edge-deposited power is promptly conducted to the divertor. This correlates with the loss of current drive efficiency at high density previously observed on Alcator C-Mod, and displaying characteristics that contrast with the local RF edge absorption seen on other tokamaks. Measurements of ionization in the active divertor show dramatic changes due to LHRF power, implying that divertor region can be key for the LHRF edge power deposition physics. These observations support the existence a loss mechanism near the edge for LHRF at high density (ne > 1 . 0 .1020 [m-3]). Results will be shown addressing the distribution of power within the SOL, including the toroidal symmetry and radial distribution. These characteristics are important for deducing the cause of the reduced LHCD efficiency at high density and motivates the tailoring of wave propagation to minimize SOL interaction, for example, through the use of high-field-side launch. This work was performed on the Alcator C-Mod tokamak, a DoE Office of Science user facility, and is supported by USDoE award DE-FC02-99ER54512.

Sylow p-groups of polynomial permutations on the integers mod pn☆

PubMed Central

Frisch, Sophie; Krenn, Daniel

2013-01-01

We enumerate and describe the Sylow p-groups of the groups of polynomial permutations of the integers mod pn for n⩾1 and of the pro-finite group which is the projective limit of these groups. PMID:26869732

Mod-2 wind turbine system development. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1982-01-01

The development of the MOD-2 wind turbine through acceptance testing and initial operational evaluation is documented. Pitch control hydraulic system, yaw control system, drive train, electrical power station, control system, operations and maintenance experience, and availability are discussed.

Noise Exposure Model (MOD 4)

DOT National Transportation Integrated Search

1971-08-01

The purpose of this report is threefold: : 1. To record the results of efforts at the Transportaiton Systems Center to refine and expand the Noise Exposure Model, which have specifically resulted in the MOD 4 ver described herein; : 2. To serve as an...

Noise Exposure Model MOD-5 : Volume 1

DOT National Transportation Integrated Search

1971-06-01

The report contains three sections. The first two sections are contained in Volume 1. It contains an airport analysis which describes the noise exposure model MOD-5 from the perspective of analysing an airport in order to develop the program input mo...

Advanced multi-megawatt wind turbine design for utility application

NASA Technical Reports Server (NTRS)

Pijawka, W. C.

1984-01-01

A NASA/DOE program to develop a utility class multimegawatt wind turbine, the MOD-5A, is described. The MOD-5A features a 400 foot diameter rotor which is teetered and positioned upwind of the tower; a 7.3 megawatt power rating with a variable speed electric generating system; and a redundant rotor support and torque transmission structure. The rotor blades were fabricated from an epoxy-bonded wood laminate material which was a successful outgrowth of the MOD-OA airfoil design. Preliminary data from operational tests carried out at the NASA Plumbrook test facility are presented.

Advanced multi-megawatt wind turbine design for utility application

NASA Astrophysics Data System (ADS)

Pijawka, W. C.

1984-08-01

A NASA/DOE program to develop a utility class multimegawatt wind turbine, the MOD-5A, is described. The MOD-5A features a 400 foot diameter rotor which is teetered and positioned upwind of the tower; a 7.3 megawatt power rating with a variable speed electric generating system; and a redundant rotor support and torque transmission structure. The rotor blades were fabricated from an epoxy-bonded wood laminate material which was a successful outgrowth of the MOD-OA airfoil design. Preliminary data from operational tests carried out at the NASA Plumbrook test facility are presented.

MOD silver metallization for photovoltaics

NASA Technical Reports Server (NTRS)

Vest, G. M.; Vest, R. W.

1984-01-01

The development of flat plate solar arrays is reported. Photovoltaic cells require back side metallization and a collector grid system on the front surface. Metallo-organic decomposition (MOD) silver films can eliminate most of the present problems with silver conductors. The objectives are to: (1) identify and characterize suitable MO compounds; (2) develop generic synthesis procedures for the MO compounds; (3) develop generic fabrication procedures to screen printable MOD silver inks; (4) optimize processing conditions to produce grid patterns and photovoltaic cells; and (5) develop a model which describes the adhesion between the fired silver film and the silicon surface.

Utility operational experience on the NASA/DOE MOD-0A 200-kW wind turbine

NASA Technical Reports Server (NTRS)

Glasgow, J. C.; Robbins, W. H.

1979-01-01

The Mod-0A 200 wind turbine was designed and fabricated as part of the Federal Wind Energy Program. Early wind turbine operation and performance data were obtained while gaining initial experience in the operation of large, horizontal axis wind turbines in typical utility environments. The Mod-0A wind turbine was turned over to the Town of Clayton Light and Water Plant, Clayton, NM, for utility operation and on December 31, 1978, the machine had completed ten months of utility operation. The machine is described and the recent operational experience at Clayton, NMis documented.

Osteogenic response of human MSCs and osteoblasts to hydrophilic and hydrophobic nanostructured titanium implant surfaces.

PubMed

Lotz, Ethan M; Olivares-Navarrete, Rene; Berner, Simon; Boyan, Barbara D; Schwartz, Zvi

2016-12-01

Microstructured implant surfaces created by grit blasting and acid etching titanium (Ti) support osseointegration. This effect is further enhanced by storing in aqueous solution to retain hydrophilicity, but this also leads to surface nanostructure formation. The purpose of this study was to assess the contributions of nanostructures on the improved osteogenic response of osteoblast lineage cells to hydrophilic microstructured Ti. Human mesenchymal stem cells (MSCs) and normal human osteoblasts (NHOsts) were cultured separately on non-nanostructured/hydrophobic (SLA), nanostructured/hydrophilic (modSLA), or nanostructured/hydrophobic (SLAnano) Ti surfaces. XPS showed elevated carbon levels on SLA and SLAnano compared to modSLA. Contact angle measurements indicated only modSLA was hydrophilic. Confocal laser microscopy revealed minor differences in mean surface roughness. SEM showed the presence of nanostructures on modSLA and SLAnano. MSCs and NHOst cells exhibited similar morphology on the substrates and osteoblastic differentiation and maturation were greatest on modSLA. These results suggest that when the appropriate microstructure is present, hydrophilicity may play a greater role in stimulating MSC and NHOst osteoblastic differentiation and maturation than the presence of nanostructures generated during storage in an aqueous environment. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 3137-3148, 2016. © 2016 Wiley Periodicals, Inc.

Flight controller alertness and performance during MOD shiftwork operations

NASA Technical Reports Server (NTRS)

Kelly, Sean M.; Rosekind, Mark R.; Dinges, David F.; Miller, Donna L.; Gillen, Kelly A.; Gregory, Kevin B.; Aguilar, Ronald D.; Smith, Roy M.

1994-01-01

Decreased alertness and performance associated with fatigue, sleep loss, and circadian disruption are issues faced by a diverse range of shiftwork operations. During STS operations, MOD personnel provide 24 hr. coverage of critical tasks. A joint JSC and ARC project was undertaken to examine these issues in flight controllers during MOD shiftwork operations. An initial operational test of procedures and measures was conducted during STS-53 in Dec. 1992. The study measures included a background questionnaire, a subjective daily logbook completed on a 24 hr. basis (to report sleep patterns, work periods, etc.), and an 8 minute performance and mood test battery administered at the beginning, middle, and end of each shift period. Seventeen Flight controllers representing the 3 Orbit shifts participated. The initial results clearly support further data collection during other STS missions to document baseline levels of alertness and performance during MOD shiftwork operations. These issues are especially pertinent for the night shift operations and the acute phase advance required for the transition of day shift personnel into the night for shuttle launch. Implementation and evaluation of the countermeasure strategies to maximize alertness and performance is planned. As STS missions extend to further extended duration orbiters, timelines and planning for 24 circadian disruption will remain highly relevant in the MOD environment.

Incipient evolution of Wolbachia compatibility types.

PubMed

Charlat, Sylvain; Riegler, Markus; Baures, Isabelle; Poinsot, Denis; Stauffer, Christian; Merçot, Hervé

2004-09-01

Cytoplasmic incompatibility (CI) is induced in arthropods by the maternally inherited bacterium Wolbachia. When infected males mate with uninfected females or with females bearing a different Wolbachia variant, paternal chromosomes behave abnormally and embryos die. This pattern can be interpreted as resulting from two bacterial effects: One (usually termed mod, for modification) would affect sperm and induce embryo death, unless Wolbachia is also present in the egg, which implies the existence of a second effect, usually termed resc, for rescue. The fact that CI can occur in crosses between males and females infected by different Wolbachia shows that mod and resc interact in a specific manner. In other words, different compatibility types, or mod/resc pairs seem to have diverged from one (or a few) common ancestor(s). We are interested in the process allowing the evolution of mod/resc pairs. Here this question is addressed experimentally after cytoplasmic injection into a single host species (Drosophila simulans) by investigating compatibility relationships between closely related Wolbachia variants naturally evolving in different dipteran hosts: D. simulans, Drosophila melanogaster, and Rhagoletis cerasi. Our results suggest that closely related bacteria can be totally or partially incompatible. The compatibility relationships observed can be explained using a formal description of the mod and resc functions, implying both qualitative and quantitative variations.

Assessment of Fetal Myocardial Performance Index in Women with Placenta Previa.

PubMed

Zhang, Na; Sun, Lijuan; Zhang, Lina; Li, Zhen; Han, Jijing; Wu, Qingqing

2017-12-15

BACKGROUND This study investigated whether fetuses of placenta previa pregnancies have cardiac dysfunction by use of a modified myocardial performance index (Mod-MPI). MATERIAL AND METHODS A prospective cross-sectional study was conducted including 178 fetuses at 28-40 weeks of gestation. Eighty-nine fetuses of mothers with placenta previa and without pregnancy complications were recruited (placenta previa group) and matched with 89 fetuses of mothers with normal pregnancies (control group). Fetal cardiac function parameters and perinatal outcomes as well as the Mod-MPI were compared between the 2 groups. RESULTS The median Mod-MPI was significantly increased in fetuses of mothers with placenta previa compared with controls (0.47±0.05 vs. 0.45±0.05; P<0.01). Among fetuses of mothers with or without placenta previa, the Mod-MPI was significantly higher in the incomplete placenta previa group compared with the complete placenta previa group and control group (P<0.01). An increased Mod-MPI in placenta previa pregnancies was independently associated with fetal cord pH <7.2 (odds ratio, 4.8; 95% confidence interval, 0.98-23.54; P=0.003). CONCLUSIONS There is impairment of fetal cardiac function in pregnancies with placenta previa. An increased MPI was independently associated with adverse perinatal outcomes to some extent in the placenta previa pregnancies.

GPCR-ModSim: A comprehensive web based solution for modeling G-protein coupled receptors

PubMed Central

Esguerra, Mauricio; Siretskiy, Alexey; Bello, Xabier; Sallander, Jessica; Gutiérrez-de-Terán, Hugo

2016-01-01

GPCR-ModSim (http://open.gpcr-modsim.org) is a centralized and easy to use service dedicated to the structural modeling of G-protein Coupled Receptors (GPCRs). 3D molecular models can be generated from amino acid sequence by homology-modeling techniques, considering different receptor conformations. GPCR-ModSim includes a membrane insertion and molecular dynamics (MD) equilibration protocol, which can be used to refine the generated model or any GPCR structure uploaded to the server, including if desired non-protein elements such as orthosteric or allosteric ligands, structural waters or ions. We herein revise the main characteristics of GPCR-ModSim and present new functionalities. The templates used for homology modeling have been updated considering the latest structural data, with separate profile structural alignments built for inactive, partially-active and active groups of templates. We have also added the possibility to perform multiple-template homology modeling in a unique and flexible way. Finally, our new MD protocol considers a series of distance restraints derived from a recently identified conserved network of helical contacts, allowing for a smoother refinement of the generated models which is particularly advised when there is low homology to the available templates. GPCR- ModSim has been tested on the GPCR Dock 2013 competition with satisfactory results. PMID:27166369

MOD: An Organic Detector for the Future Exploration of Mars

NASA Technical Reports Server (NTRS)

Kminek, G.; Bada, J. L.; Botta, O.; Grunthaner, F.; Glavin, D. P.

1999-01-01

The Mars Organic Detector (MOD) is designed to assess whether organic compounds, possibly associated with life, are present in Martian rock and soil samples. MOD has a detection limit that is at least two orders of magnitude more sensitive than the Viking GCMS. MOD is focused on detecting amino acids, amines and PAH (polycyclic aromatic hydrocarbons). Amino acids play an essential role in biochemistry on Earth and PAH are widespread throughout the universe and can provide an indication of the delivery of meteoritic organic material to Mars. The advantage of MOD is the absence of wet chemistry and its simple and robust design. The sample will be extracted from the mineral matrix (0.1 - 1 g of rock-powder) using sublimation and analyzed with a fluorescence detector. The isolation method is based on the fact that amino acids and PAH are volatile at temperatures greater than 150C. The fluorescence detection scheme is based on UV excitation with LED's, optical filters, PrN diode photon detector and a sample calibration reservoir. Fluorescamine is used as a fluorescing reagent for amino acids and amines, while PAH are naturally fluorescent. There is no sample preparation required and the turnaround time for a single analysis is on the order of minutes.

The Satellite Data Thematic Core Service within the EPOS Research Infrastructure

NASA Astrophysics Data System (ADS)

Manunta, Michele; Casu, Francesco; Zinno, Ivana; De Luca, Claudio; Buonanno, Sabatino; Zeni, Giovanni; Wright, Tim; Hooper, Andy; Diament, Michel; Ostanciaux, Emilie; Mandea, Mioara; Walter, Thomas; Maccaferri, Francesco; Fernandez, Josè; Stramondo, Salvatore; Bignami, Christian; Bally, Philippe; Pinto, Salvatore; Marin, Alessandro; Cuomo, Antonio

2017-04-01

EPOS, the European Plate Observing System, is a long-term plan to facilitate the integrated use of data, data products, software and services, available from distributed Research Infrastructures (RI), for solid Earth science in Europe. Indeed, EPOS integrates a large number of existing European RIs belonging to several fields of the Earth science, from seismology to geodesy, near fault and volcanic observatories as well as anthropogenic hazards. The EPOS vision is that the integration of the existing national and trans-national research infrastructures will increase access and use of the multidisciplinary data recorded by the solid Earth monitoring networks, acquired in laboratory experiments and/or produced by computational simulations. The establishment of EPOS will foster the interoperability of products and services in the Earth science field to a worldwide community of users. Accordingly, the EPOS aim is to integrate the diverse and advanced European Research Infrastructures for solid Earth science, and build on new e-science opportunities to monitor and understand the dynamic and complex solid-Earth System. One of the EPOS Thematic Core Services (TCS), referred to as Satellite Data, aims at developing, implementing and deploying advanced satellite data products and services, mainly based on Copernicus data (namely Sentinel acquisitions), for the Earth science community. This work intends to present the technological enhancements, fostered by EPOS, to deploy effective satellite services in a harmonized and integrated way. In particular, the Satellite Data TCS will deploy five services, EPOSAR, GDM, COMET, 3D-Def and MOD, which are mainly based on the exploitation of SAR data acquired by the Sentinel-1 constellation and designed to provide information on Earth surface displacements. In particular, the planned services will provide both advanced DInSAR products (deformation maps, velocity maps, deformation time series) and value-added measurements (source model, 3D displacement maps, seismic hazard maps). Moreover, the services will release both on-demand and systematic products. The latter will be generated and made available to the users on a continuous basis, by processing each Sentinel-1 data once acquired, over a defined number of areas of interest; while the former will allow users to select data, areas, and time period to carry out their own analyses via an on-line platform. The satellite components will be integrated within the EPOS infrastructure through a common and harmonized interface that will allow users to search, process and share remote sensing images and results. This gateway to the satellite services will be represented by the ESA- Geohazards Exploitation Platform (GEP), a new cloud-based platform for the satellite Earth Observations designed to support the scientific community in the understanding of high impact natural disasters. Satellite Data TCS will use GEP as the common interface toward the main EPOS portal to provide EPOS users not only with data products but also with relevant processing and visualisation software, thus allowing users to gather and process on a cloud-computing infrastructure large datasets without any need to download them locally.

Modifications to Langley 0.3-m TCT adaptive wall software for heavy gas test medium, phase 1 studies

NASA Technical Reports Server (NTRS)

Murthy, A. V.

1992-01-01

The scheme for two-dimensional wall adaptation with sulfur hexafluoride (SF6) as test gas in the NASA Langley Research Center 0.3-m Transonic Cryogenic Tunnel (0.3-m TCT) is presented. A unified version of the wall adaptation software has been developed to function in a dual gas operation mode (nitrogen or SF6). The feature of ideal gas calculations for nitrogen operation is retained. For SF6 operation, real gas properties have been computed using the departure function technique. Installation of the software on the 0.3-m TCT ModComp-A computer and preliminary validation with nitrogen operation were found to be satisfactory. Further validation and improvements to the software will be undertaken when the 0.3-m TCT is ready for operation with SF6 gas.

A Fortran-90 Based Multiprecision System

NASA Technical Reports Server (NTRS)

Bailey, David H.; Lasinski, T. A. (Technical Monitor)

1994-01-01

The author has developed a new version of his Fortran multiprecision computation system that is based on the Fortran-90 language. With this new approach, a translator program is not required - translation of Fortran code for multiprecision is accomplished by merely utilizing advanced features of Fortran-90, such as derived data types and operator extensions. This approach results in more reliable translation and also permits programmers of multiprecision applications to utilize the full power of the Fortran-90 language. Three multiprecision datatypes are supported in this system: multiprecision integer. real and complex. All the usual Fortran conventions for mixed mode operations are supported, and many of the Fortran intrinsics, such as SIN, EXP and MOD, are supported with multiprecision arguments. This paper also briefly describes an interesting application of this software, wherein new number-theoretic identities have been discovered by means of multiprecision computations.

85. Command HQ. SAC control center (MOD) new work cross ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

85. Command HQ. SAC control center (MOD) new work cross section, drawing number AW-30-02-07, dated 7 February, 1962 - Offutt Air Force Base, Strategic Air Command Headquarters & Command Center, Headquarters Building, 901 SAC Boulevard, Bellevue, Sarpy County, NE

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Rohdenburg, C.; Antonelli, M. (Editor)

1983-01-01

Program status and plans are discussed for component and technology development; reference engine system design, the upgraded Mod 1 engine; industry test and evaluation; and product assurance. Four current Mod 1 engines reached a total of 2523 operational hours, while two upgraded engines accumulated 166 hours.

Gender differences in the use of computers, programming, and peer interactions in computer science classrooms

NASA Astrophysics Data System (ADS)

Stoilescu, Dorian; Egodawatte, Gunawardena

2010-12-01

Research shows that female and male students in undergraduate computer science programs view computer culture differently. Female students are interested more in the use of computers than in doing programming, whereas male students see computer science mainly as a programming activity. The overall purpose of our research was not to find new definitions for computer science culture but to see how male and female students see themselves involved in computer science practices, how they see computer science as a successful career, and what they like and dislike about current computer science practices. The study took place in a mid-sized university in Ontario. Sixteen students and two instructors were interviewed to get their views. We found that male and female views are different on computer use, programming, and the pattern of student interactions. Female and male students did not have any major issues in using computers. In computing programming, female students were not so involved in computing activities whereas male students were heavily involved. As for the opinions about successful computer science professionals, both female and male students emphasized hard working, detailed oriented approaches, and enjoying playing with computers. The myth of the geek as a typical profile of successful computer science students was not found to be true.

Coagulofibrinolytic changes in patients with disseminated intravascular coagulation associated with post-cardiac arrest syndrome--fibrinolytic shutdown and insufficient activation of fibrinolysis lead to organ dysfunction.

PubMed

Wada, Takeshi; Gando, Satoshi; Mizugaki, Asumi; Yanagida, Yuichiro; Jesmin, Subrina; Yokota, Hiroyuki; Ieko, Masahiro

2013-07-01

Post-cardiac arrest syndrome (PCAS) is often associated with disseminated intravascular coagulation (DIC), thus leading to the development of multiple organ dysfunction syndrome (MODS). The aim of this study was to examine the pathophysiological relationships between coagulation, fibrinolysis and fibrinolytic shutdown by evaluating the levels of coagulofibrinolytic markers, including soluble fibrin, thrombin-activatable fibrinolysis inhibitor (TAFI), tissue plasminogen activator-plasminogen activator inhibitor-1 complex (tPAIC), plasmin-alpha2 plasmin inhibitor complex (PPIC), neutrophil elastase and fibrin degradation product by neutrophil elastase (EXDP). Fifty-two resuscitated patients were divided into two groups: 22 DIC and 30 non-DIC patients. The levels of soluble fibrin, PPIC, tPAIC, EXDP and neutrophil elastase in the DIC patients with PCAS were significantly higher than those observed in the non-DIC patients. The values of the tPAIC and JAAM DIC scores were found to be independent predictors of increased SOFA scores in the DIC patients. The MODS patients demonstrated significantly higher levels of soluble fibrin and tPAIC; however, the levels of TAFI and EXDP were identical between the patients with and without MODS. In addition, positive correlations were observed between the levels of tPAIC and EXDP in the patients with non-MODS; however, no correlations were observed between these markers in the MODS patients. Thrombin activation and fibrinolytic shutdown play important roles in the development of organ dysfunction in PCAS patients. Neutrophil elastase-mediated fibrinolysis cannot overcome the fibrinolytic shutdown that occurs in DIC patients with PCAS, thus resulting in the development of MODS. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Modularity-Based Method Reveals Mixed Modules from Chemical-Gene Heterogeneous Network

PubMed Central

Song, Jianglong; Tang, Shihuan; Liu, Xi; Gao, Yibo; Yang, Hongjun; Lu, Peng

2015-01-01

For a multicomponent therapy, molecular network is essential to uncover its specific mode of action from a holistic perspective. The molecular system of a Traditional Chinese Medicine (TCM) formula can be represented by a 2-class heterogeneous network (2-HN), which typically includes chemical similarities, chemical-target interactions and gene interactions. An important premise of uncovering the molecular mechanism is to identify mixed modules from complex chemical-gene heterogeneous network of a TCM formula. We thus proposed a novel method (MixMod) based on mixed modularity to detect accurate mixed modules from 2-HNs. At first, we compared MixMod with Clauset-Newman-Moore algorithm (CNM), Markov Cluster algorithm (MCL), Infomap and Louvain on benchmark 2-HNs with known module structure. Results showed that MixMod was superior to other methods when 2-HNs had promiscuous module structure. Then these methods were tested on a real drug-target network, in which 88 disease clusters were regarded as real modules. MixMod could identify the most accurate mixed modules from the drug-target 2-HN (normalized mutual information 0.62 and classification accuracy 0.4524). In the end, MixMod was applied to the 2-HN of Buchang naoxintong capsule (BNC) and detected 49 mixed modules. By using enrichment analysis, we investigated five mixed modules that contained primary constituents of BNC intestinal absorption liquid. As a matter of fact, the findings of in vitro experiments using BNC intestinal absorption liquid were found to highly accord with previous analysis. Therefore, MixMod is an effective method to detect accurate mixed modules from chemical-gene heterogeneous networks and further uncover the molecular mechanism of multicomponent therapies, especially TCM formulae. PMID:25927435

Comparison of removal torques between laser-etched and modified sandblasted acid-etched Ti implant surfaces in rabbit tibias

PubMed Central

Al Awamleh, Abdel Ghani Ibrahim

2018-01-01

PURPOSE The purpose of this study was to analyze the effects of two different implant surface treatments on initial bone connection by comparing the Removal Torque Values (RTQs) at 7 and 10 days after chemically modified, sandblasted, large-grit and acid-etched (modSLA), and Laser-etched (LE) Ti implant placements. MATERIALS AND METHODS Twenty modSLA and 20 LE implants were installed on the left and right tibias of 20 adult rabbits. RTQs were measured after 7 and 10 days in 10 rabbits each. Scanning electron microscope (SEM) photographs of the two implants were observed by using Quanta FEG 650 from the FEI company (Hillsboro, OR, USA). Analyses of surface elements and components were conducted using energy dispersive spectroscopy (EDS, Horiba, Kyoto, Japan). RESULTS The mean RTQs were 12.29 ± 0.830 and 12.19 ± 0.713 Ncm after 7 days (P=.928) and 16.47 ± 1.324 and 16.17 ± 1.165 Ncm after 10 days (P=.867) for LE and modSLA, respectively, indicating no significant inter-group differences. Pore sizes in the LE were 40 µm and consisted of numerous small pores, whereas pore sizes in the modSLA were 5 µm. In the EDS analysis, Ti, O, and C were the only three elements found in the LE surfaces. Na, Ca, Cl, and K were also observed in modSLA, in addition to Ti, O, and C. CONCLUSION The implants showed no significant difference in biomechanical bond strength to bone in early-stage osseointegration. LE implant can be considered an excellent surface treatment method in addition to the modSLA implant and can be applied to the early loading of the prosthesis clinically. PMID:29503717

Microscopic observation drug-susceptibility assay vs. Xpert® MTB/RIF for the diagnosis of tuberculosis in a rural African setting: a cost-utility analysis.

PubMed

Wikman-Jorgensen, Philip E; Llenas-García, Jara; Pérez-Porcuna, Tomàs M; Hobbins, Michael; Ehmer, Jochen; Mussa, Manuel A; Ascaso, Carlos

2017-06-01

To compare the cost-utility of microscopic observation drug-susceptibility assay (MODS) and Xpert ® MTB/RIF implementation for tuberculosis (TB) diagnosis in rural northern Mozambique. Stochastic transmission compartmental TB model from the healthcare provider perspective with parameter input from direct measurements, systematic literature reviews and expert opinion. MODS and Xpert ® MTB/RIF were evaluated as replacement test of smear microscopy (SM) or as an add-on test after a negative SM. Costs were calculated in 2013 USD, effects in disability-adjusted life years (DALY). Willingness to pay threshold (WPT) was established at once the per capita Gross National Income of Mozambique. MODS as an add-on test to negative SM produced an incremental cost-effectiveness ratio (ICER) of 5647.89USD/DALY averted. MODS as a substitute for SM yielded an ICER of 5374.58USD/DALY averted. Xpert ® MTB/RIF as an add-on test to negative SM yielded ICER of 345.71USD/DALY averted. Xpert ® MTB/RIF as a substitute for SM obtained an ICER of 122.13USD/DALY averted. TB prevalence and risk of infection were the main factors impacting MODS and Xpert ® MTB/RIF ICER in the one-way sensitivity analysis. In the probabilistic sensitivity analysis, Xpert ® MTB/RIF was most likely to have an ICER below the WPT, whereas MODS was not. Our cost-utility analysis favours the implementation of Xpert ® MTB/RIF as a replacement of SM for all TB suspects in this rural high TB/HIV prevalence African setting. © 2017 John Wiley & Sons Ltd.

High plasma levels of high mobility group box 1 is associated with the risk of sepsis in severe blunt chest trauma patients: a prospective cohort study.

PubMed

Wang, Xiao-Wen; Karki, Avash; Zhao, Xing-Ji; Xiang, Xiao-Yong; Lu, Zhi-Qian

2014-08-02

High mobility group box 1 (HMGB1) is a late mediator of systemic inflammation. Extracellular HMGB1 play a central pathogenic role in critical illness. The purpose of the study was to investigate the association between plasma HMGB1 concentrations and the risk of poor outcomes in patients with severe blunt chest trauma. The plasma concentrations of HMGB1 in patients with severe blunt chest trauma (AIS ≥ 3) were measured by a quantitative enzyme-linked immunosorbent assay at four time points during seven days after admission, and the dynamic release patterns were monitored. The biomarker levels were compared between patients with sepsis and non-sepsis, and between patients with multiple organ dysfunction syndrome (MODS) and non-MODS. The related factors of prognosis were analyzed by using multivariate logistic regression analysis. The short-form 36 was used to evaluate the quality of life of patients at 12 months after injury. Plasma HMGB1 levels were significantly higher both in sepsis and MODS group on post-trauma day 3, 5, and 7 compared with the non-sepsis and non-MODS groups, respectively. Multivariate analysis showed that HMGB1 levels and ISS were independent risk factors for sepsis and MODS in patients with severe blunt chest trauma. Plasma HMGB1 levels were significantly elevated in patients with severe blunt chest trauma. HMGB1 levels were associated with the risk of poor outcome in patients with severe blunt chest trauma. Daily HMGB1 levels measurements is a potential useful tool in the early identification of post-trauma complications. Further studies are needed to determine whether HMGB1 intervention could prevent the development of sepsis and MODS in patients with severe blunt chest trauma.

Cerebral Palsy and Growth Failure at 6 to 7 Years

PubMed Central

Stephens, Bonnie E.; McDonald, Scott A.; Ehrenkranz, Richard A.; Laptook, Abbot R.; Pappas, Athina; Hintz, Susan R.; Shankaran, Seetha; Higgins, Rosemary D.; Das, Abhik

2013-01-01

OBJECTIVE: To evaluate the association between severity of cerebral palsy (CP) and growth to 6 to 7 years of age among children with moderate to severe (Mod/Sev) hypoxic ischemic encephalopathy (HIE). It was hypothesized that children with Mod/Sev CP would have poorer growth, lower cognitive scores, and increased rehospitalization rates compared with children with no CP (No CP). METHODS: Among 115 of 122 surviving children followed in the hypothermia trial for neonatal HIE, growth parameters and neurodevelopmental status at 18 to 22 months and 6 to 7 years were available. Group comparisons (Mod/Sev CP and No CP) with unadjusted and adjusted analyses for growth <10th percentile and z scores by using Fisher’s exact tests and regression modeling were conducted. RESULTS: Children with Mod/Sev CP had high rates of slow growth and cognitive and motor impairment and rehospitalizations at 18 to 22 months and 6 to 7 years. At 6 to 7 years of age, children with Mod/Sev CP had increased rates of growth parameters <10th percentile compared with those with No CP (weight, 57% vs 3%; height, 70% vs 2%; and head circumference, 82% vs 13%; P < .0001). Increasing severity of slow growth was associated with increasing age (P < .04 for weight, P < .001 for length, and P < .0001 for head circumference). Gastrostomy feeds were associated with better growth. CONCLUSIONS: Term children with HIE who develop Mod/Sev CP have high and increasing rates of growth <10th percentile by 6 to 7 years of age. These findings support the need for close medical and nutrition management of children with HIE who develop CP. PMID:24019415

Changing impact of modifiable risk factors on the incidence of major outcomes of type 1 diabetes: the Pittsburgh Epidemiology of Diabetes Complications Study.

PubMed

Miller, Rachel G; Secrest, Aaron M; Ellis, Demetrius; Becker, Dorothy J; Orchard, Trevor J

2013-12-01

The incidence of type 1 diabetes complications appears to be decreasing, but relative contributions of risk factors are unclear. We thus estimated the effect of modifiable risk factors on the incidence of a composite end point, major outcomes of diabetes (MOD). The Pittsburgh Epidemiology of Diabetes Complications (EDC) Study was used to derive two cohorts based on diabetes diagnosis year (1960-1969 and 1970-1980). Baseline exam data in the current analysis for the 1960s group were collected in 1986-1988 and for the 1970s in 1996-1998. Each group was followed for 8 years for MOD incidence (diabetes-related death, myocardial infarction, revascularization procedure/blockage ≥50%, stroke, end-stage renal disease, blindness, and amputation). Assessed risk factors include the following: HbA1c, hypertension, microalbuminuria, BMI, hypercholesterolemia, and smoking. Accelerated failure time models were used to estimate the acceleration factor. MOD incidence decreased in the 1970s cohort (15.8% [95% CI 11.6-21.4]) compared with the 1960s (22.6% [17.0-29.1]) over the 8-year follow-up (P = 0.06). Hypertension and microalbuminuria were associated with significantly accelerated MOD incidence in both cohorts (P < 0.01 for both). High HbA1c (P = 0.0005), hypercholesterolemia (P = 0.01), and current smoking (P = 0.003) significantly accelerated the incidence of MOD in the 1960s but not 1970s cohort. BMI was not associated with MOD in either cohort. These results suggest that hypertension and microalbuminuria remain important predictors of complications that are not being adequately addressed.

Effect of bulk-fill base material on fracture strength of root-filled teeth restored with laminate resin composite restorations.

PubMed

Taha, N A; Maghaireh, G A; Ghannam, A S; Palamara, J E

2017-08-01

To evaluate the effect of using a bulk-fill flowable base material on fracture strength and fracture patterns of root-filled maxillary premolars with MOD preparations restored with laminate restorations. Fifty extracted maxillary premolars were selected for the study. Standardized MOD cavities with endodontic treatment were prepared for all teeth, except for intact control. The teeth were divided randomly into five groups (n=10); (Group 1) sound teeth, (Group 2) unrestored teeth; (Group 3) MOD cavities with Vitrebond base and resin-based composite (Ceram. X One Universal); (Group 4) MOD cavities with 2mm GIC base (Fuji IX GP) and resin-based composite (Ceram. X One Universal) open laminate, (Group 5) MOD cavities were restored with 4mm of bulk-fill flowable base material (SDR) and resin-based composite (Ceram. X One Universal). All teeth were thermocycled and subjected to a 45° ramped oblique load in a universal testing machine. Fracture load and fracture patterns were recorded. Data were analyzed using one-way ANOVA and Dunnett's T3 test. Restoration in general increased the fracture strength compared to unrestored teeth. The fracture strength of group 5 (bulk-fill) was significantly higher than the fracture strength of the GIC laminate groups and not significantly different from the intact teeth (355±112N, P=0.118). The type of failure was unfavorable for most of the groups, with the majority being mixed failures. The use of a bulk-fill flowable base material significantly increased the fracture strength of extracted root-filled teeth with MOD cavities; however it did not improve fracture patterns to more favorable ones. Investigating restorative techniques that may improve the longevity of root-filled premolar teeth restored with direct resin restorations. Copyright © 2017 Elsevier Ltd. All rights reserved.

PeakRanger: A cloud-enabled peak caller for ChIP-seq data

PubMed Central

2011-01-01

Background Chromatin immunoprecipitation (ChIP), coupled with massively parallel short-read sequencing (seq) is used to probe chromatin dynamics. Although there are many algorithms to call peaks from ChIP-seq datasets, most are tuned either to handle punctate sites, such as transcriptional factor binding sites, or broad regions, such as histone modification marks; few can do both. Other algorithms are limited in their configurability, performance on large data sets, and ability to distinguish closely-spaced peaks. Results In this paper, we introduce PeakRanger, a peak caller software package that works equally well on punctate and broad sites, can resolve closely-spaced peaks, has excellent performance, and is easily customized. In addition, PeakRanger can be run in a parallel cloud computing environment to obtain extremely high performance on very large data sets. We present a series of benchmarks to evaluate PeakRanger against 10 other peak callers, and demonstrate the performance of PeakRanger on both real and synthetic data sets. We also present real world usages of PeakRanger, including peak-calling in the modENCODE project. Conclusions Compared to other peak callers tested, PeakRanger offers improved resolution in distinguishing extremely closely-spaced peaks. PeakRanger has above-average spatial accuracy in terms of identifying the precise location of binding events. PeakRanger also has excellent sensitivity and specificity in all benchmarks evaluated. In addition, PeakRanger offers significant improvements in run time when running on a single processor system, and very marked improvements when allowed to take advantage of the MapReduce parallel environment offered by a cloud computing resource. PeakRanger can be downloaded at the official site of modENCODE project: http://www.modencode.org/software/ranger/ PMID:21554709

MOD control center automated information systems security evolution

NASA Technical Reports Server (NTRS)

Owen, Rich

1991-01-01

The role of the technology infusion process in future Control Center Automated Information Systems (AIS) is highlighted. The following subject areas are presented in the form of the viewgraphs: goals, background, threat, MOD's AISS program, TQM, SDLC integration, payback, future challenges, and bottom line.

Appendix C : the Noise Exposure Model (MOD 4)

DOT National Transportation Integrated Search

1971-08-01

The purpose of this report is threefold: 1. To record the results of efforts at the Transportaiton Systems Center to refine and expand the Noise Exposure Model, which have specifically resulted in the MOD 4 ver described herein; 2. To serve as an Use...

A methodology for assessment of wind turbine noise generation

NASA Astrophysics Data System (ADS)

Kelley, N. D.; Hemphill, R. R.; McKenna, H. E.

1982-05-01

An investigation of the sources of impulsive noise generated by the operation of the Mod 1 2 MW wind turbine was performed to establish criteria for assessing the noise-producing potential of other large wind turbines. Unsteady loading of the rotors was determined to be the cause of the sound pressure, which was generally below 100 Hz. Complaints originated from people in dwellings with a room with a window facing the machine. Indoor monitoring revealed pressure traces in the 31.5 Hz band with energy densities exceeding background by about 30 dB. It was concluded that the sound pressure was conveyed by the walls acting as a diaphragm. The induced vibration coupled with human body fundamental modes to produce a feeling of whole-body vibration. Spectral analyses were made of the vibration fields of the Mod 2, a 17 m Darrieus, and a Mod OA to allow comparison with the nuisance points of the Mod 1. Sound pressure levels were found at certain frequencies which would eliminate the occurrence of acoustic pollution.

Comparison of tungsten nano-tendrils grown in Alcator C-Mod and linear plasma devices

NASA Astrophysics Data System (ADS)

Wright, G. M.; Brunner, D.; Baldwin, M. J.; Bystrov, K.; Doerner, R. P.; Labombard, B.; Lipschultz, B.; De Temmerman, G.; Terry, J. L.; Whyte, D. G.; Woller, K. B.

2013-07-01

Growth of tungsten nano-tendrils ("fuzz") has been observed for the first time in the divertor region of a high-power density tokamak experiment. After 14 consecutive helium L-mode discharges in Alcator C-Mod, the tip of a tungsten Langmuir probe at the outer strike point was fully covered with a layer of nano-tendrils. The depth of the W fuzz layer (600 ± 150 nm) is consistent with an empirical growth formula from the PISCES experiment. Re-creating the C-Mod exposures as closely as possible in Pilot-PSI experiment can produce nearly-identical nano-tendril morphology and layer thickness at surface temperatures that agree with uncertainties with the C-Mod W probe temperature data. Helium concentrations in W fuzz layers are measured at 1-4 at.%, which is lower than expected for the observed sub-surface voids to be filled with several GPa of helium pressure. This possibly indicates that the void formation is not pressure driven.

Mission Operations Directorate - Success Legacy of the Space Shuttle Program

NASA Technical Reports Server (NTRS)

Azbell, James A.

2011-01-01

In support of the Space Shuttle Program, as well as NASA s other human space flight programs, the Mission Operations Directorate (MOD) at the Johnson Space Center has become the world leader in human spaceflight operations. From the earliest programs - Mercury, Gemini, Apollo - through Skylab, Shuttle, ISS, and our Exploration initiatives, MOD and its predecessors have pioneered ops concepts and emphasized a history of mission leadership which has added value, maximized mission success, and built on continual improvement of the capabilities to become more efficient and effective. MOD s focus on building and contributing value with diverse teams has been key to their successes both with the US space industry and the broader international community. Since their beginning, MOD has consistently demonstrated their ability to evolve and respond to an ever changing environment, effectively prepare for the expected and successfully respond to the unexpected, and develop leaders, expertise, and a culture that has led to mission and Program success.

Plasma biomarkers of SIRS and MODS associated with canine babesiosis.

PubMed

Kuleš, J; de Torre-Minguela, C; Barić Rafaj, R; Gotić, J; Nižić, P; Ceron, J J; Mrljak, V

2016-04-01

Canine babesiosis is a tick-borne disease caused by the haemoprotozoan parasites of the genus Babesia. Early detection of systemic inflammatory response syndrome (SIRS) and multiple organ dysfunction syndrome (MODS) is of major importance in clinical practice for providing information about severity and outcomes of the disease and therapy. Plasma samples were taken at admission from five dogs with uncomplicated babesiosis caused by B. canis canis, five dogs with babesiosis and SIRS, five dogs with babesiosis and MODS, and five healthy dogs. After two-dimensional electrophoresis and capillary reversed - phase liquid chromatography coupled online with tandem mass spectrometry, 68 differentially expressed spots with level of significance P<0.05 were detected between groups. SIRS in babesiosis was characterised by increases in paraoxonase 1 and apoA-I, whereas MODS with decrease of complement inhibitors leading to prolonged complement activation and decrease of vitamin D binding protein due to haemolysis and activation of the coagulation cascade. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dark matter in the local group of galaxies

NASA Astrophysics Data System (ADS)

Morley, P. D.; Buettner, D. J.

We describe the neutrino flavor (e = electron, μ = muon, τ = tau) masses as mi=e,μ,τ = m + Δmi with |Δmi| m < 1 and probably |Δmi| m ≪ 1. The quantity m is the degenerate neutrino mass. Because neutrino flavor is not a quantum number, this degenerate mass appears in the neutrino equation-of-state [P. D. Morley and D. J. Buettner, Int. J. Mod. Phys. D (2014), doi:10.1142/s0218271815500042.]. We apply a Monte Carlo computational physics technique to the Local Group (LG) of galaxies to determine an approximate location for a Dark Matter embedding Condensed Neutrino Object (CNO) [P. D. Morley and D. J. Buettner, Int. J. Mod. Phys. D (2016), doi:10.1142/s0218271816500899.]. The calculation is based on the rotational properties of the only spiral galaxies within the LG: M31, M33 and the Milky Way. CNOs could be the Dark Matter everyone is looking for and we estimate the CNO embedding the LG to have a mass 5.17 × 1015 M⊙ and a radius 1.316 Mpc, with the estimated value of m ≃ 0.8 eV/c2. The up-coming KATRIN experiment [https://www.katrin.kit.edu.] will either be the definitive result or eliminate condensed neutrinos as a Dark Matter candidate.

RELAP5/MOD2 analysis of a postulated cold leg SBLOCA'' simultaneous to a total black-out'' event in the Jose Cabrera Nuclear Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebollo, L.

1992-04-01

Several beyond-design bases cold leg small-break LOCA postulated scenarios based on the lessons learned'' in the OECD-LOFT LP-SB-3 experiment have been analyzed for the Westinghouse single loop Jose Cabrera Nuclear Power Plant belonging to the Spanish utility UNION ELECTRICA FENOSA, S.A. The analysis has been done by the utility in the Thermal-Hydraulic Accident Analysis Section of the Engineering Department of the Nuclear Division. The RELAP5/MOD2/36.04 code has been used on a CYBER 180/830 computer and the simulation includes the 6 in. RHRS charging line, the 2 in. pressurizer spray, and the 1.5 in. CVCS make-up line piping breaks. The assumptionmore » of a total black-out condition'' coincident with the occurrence of the event has been made in order to consider a plant degraded condition with total active failure of the ECCS. As a result of the analysis, estimates of the time to core overheating startup'' as well as an evaluation of alternate operator measures to mitigate the consequences of the event have been obtained. Finally a proposal for improving the LOCA emergency operating procedure (E-1) has been suggested.« less

RELAP5/MOD2 analysis of a postulated ``cold leg SBLOCA`` simultaneous to a ``total black-out`` event in the Jose Cabrera Nuclear Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebollo, L.

1992-04-01

Several beyond-design bases cold leg small-break LOCA postulated scenarios based on the ``lessons learned`` in the OECD-LOFT LP-SB-3 experiment have been analyzed for the Westinghouse single loop Jose Cabrera Nuclear Power Plant belonging to the Spanish utility UNION ELECTRICA FENOSA, S.A. The analysis has been done by the utility in the Thermal-Hydraulic & Accident Analysis Section of the Engineering Department of the Nuclear Division. The RELAP5/MOD2/36.04 code has been used on a CYBER 180/830 computer and the simulation includes the 6 in. RHRS charging line, the 2 in. pressurizer spray, and the 1.5 in. CVCS make-up line piping breaks. Themore » assumption of a ``total black-out condition`` coincident with the occurrence of the event has been made in order to consider a plant degraded condition with total active failure of the ECCS. As a result of the analysis, estimates of the ``time to core overheating startup`` as well as an evaluation of alternate operator measures to mitigate the consequences of the event have been obtained. Finally a proposal for improving the LOCA emergency operating procedure (E-1) has been suggested.« less

Investigation of the transport shortfall in Alcator C-Mod L-mode plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, N. T.; White, A. E.; Greenwald, M.

2013-03-15

A so-called 'transport shortfall,' where ion and electron heat fluxes and turbulence are underpredicted by gyrokinetic codes, has been robustly identified in DIII-D L-mode plasmas for {rho}>0.55[T. L. Rhodes et al., Nucl. Fusion 51(6), 063022 (2011); and C. Holland et al., Phys. Plasmas 16(5), 052301 (2009)]. To probe the existence of a transport shortfall across different tokamaks, a dedicated scan of auxiliary heated L-mode discharges in Alcator C-Mod are studied in detail with nonlinear gyrokinetic simulations for the first time. Two discharges, only differing by the amount of auxiliary heating are investigated using both linear and nonlinear simulation of themore » GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)]. Nonlinear gyrokinetic simulation of the low and high input power discharges reveals a discrepancy between simulation and experiment in only the electron heat flux channel of the low input power discharge. However, both discharges demonstrate excellent agreement in the ion heat flux channel, and the high input power discharge demonstrates simultaneous agreement with experiment in both the electron and ion heat flux channels. A summary of linear and nonlinear gyrokinetic results and a discussion of possible explanations for the agreement/disagreement in each heat flux channel is presented.« less

Mining Large Scale Tandem Mass Spectrometry Data for Protein Modifications Using Spectral Libraries.

PubMed

Horlacher, Oliver; Lisacek, Frederique; Müller, Markus

2016-03-04

Experimental improvements in post-translational modification (PTM) detection by tandem mass spectrometry (MS/MS) has allowed the identification of vast numbers of PTMs. Open modification searches (OMSs) of MS/MS data, which do not require prior knowledge of the modifications present in the sample, further increased the diversity of detected PTMs. Despite much effort, there is still a lack of functional annotation of PTMs. One possibility to narrow the annotation gap is to mine MS/MS data deposited in public repositories and to correlate the PTM presence with biological meta-information attached to the data. Since the data volume can be quite substantial and contain tens of millions of MS/MS spectra, the data mining tools must be able to cope with big data. Here, we present two tools, Liberator and MzMod, which are built using the MzJava class library and the Apache Spark large scale computing framework. Liberator builds large MS/MS spectrum libraries, and MzMod searches them in an OMS mode. We applied these tools to a recently published set of 25 million spectra from 30 human tissues and present tissue specific PTMs. We also compared the results to the ones obtained with the OMS tool MODa and the search engine X!Tandem.

The challenges associated with applying global models in heterogeneous landscapes: A case study using MOD17 GPP estimates in Hawaii

NASA Astrophysics Data System (ADS)

Kimball, H.; Selmants, P. C.; Running, S. W.; Moreno, A.; Giardina, C. P.

2016-12-01

In this study we evaluate the influence of spatial data product accuracy and resolution on the application of global models for smaller scale heterogeneous landscapes. In particular, we assess the influence of locally specific land cover and high-resolution climate data products on estimates of Gross Primary Production (GPP) for the Hawaiian Islands using the MOD17 model. The MOD17 GPP algorithm uses a measure of the fraction of absorbed photosynthetically active radiation from the National Aeronautics and Space Administration's Earth Observation System. This direct measurement is combined with global land cover (500-m resolution) and climate models ( 1/2-degree resolution) to estimate GPP. We first compared the alignment between the global land cover model used in MOD17 with a Hawaii specific land cover data product. We found that there was a 51.6% overall agreement between the two land cover products. We then compared four MOD17 GPP models: A global model that used the global land cover and low-resolution global climate data products, a model produced using the Hawaii specific land cover and low-resolution global climate data products, a model with global land cover and high-resolution climate data products, and finally, a model using both Hawaii specific land cover and high-resolution climate data products. We found that including either the Hawaii specific land cover or the high-resolution Hawaii climate data products with MOD17 reduced overall estimates of GPP by 8%. When both were used, GPP estimates were reduced by 16%. The reduction associated with land cover is explained by a reduction of the total area designated as evergreen broad leaf forest and an increase in the area designated as barren or sparsely vegetated in the Hawaii land cover product as compared to the global product. The climate based reduction is explained primarily by the spatial resolution and distribution of solar radiation in the Hawaiian Islands. This study highlights the importance of accuracy and resolution when applying global models to highly variable landscapes and provides an estimate of the influence of land cover and climate data products on estimates of GPP using MOD17.

A comprehensive evaluation of two MODIS evapotranspiration products over the conterminous United States: using point and gridded FLUXNET and water balance ET

USGS Publications Warehouse

Velpuri, Naga M.; Senay, Gabriel B.; Singh, Ramesh K.; Bohms, Stefanie; Verdin, James P.

2013-01-01

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. Extensive evaluation of such large scale estimates is necessary before they can be used in various applications. In this study, two monthly MODIS 1 km ET products, MODIS global ET (MOD16) and Operational Simplified Surface Energy Balance (SSEBop) ET, are validated over the conterminous United States at both point and basin scales. Point scale validation was performed using eddy covariance FLUXNET ET (FLET) data (2001–2007) aggregated by year, land cover, elevation and climate zone. Basin scale validation was performed using annual gridded FLUXNET ET (GFET) and annual basin water balance ET (WBET) data aggregated by various hydrologic unit code (HUC) levels. Point scale validation using monthly data aggregated by years revealed that the MOD16 ET and SSEBop ET products showed overall comparable annual accuracies. For most land cover types, both ET products showed comparable results. However, SSEBop showed higher performance for Grassland and Forest classes; MOD16 showed improved performance in the Woody Savanna class. Accuracy of both the ET products was also found to be comparable over different climate zones. However, SSEBop data showed higher skill score across the climate zones covering the western United States. Validation results at different HUC levels over 2000–2011 using GFET as a reference indicate higher accuracies for MOD16 ET data. MOD16, SSEBop and GFET data were validated against WBET (2000–2009), and results indicate that both MOD16 and SSEBop ET matched the accuracies of the global GFET dataset at different HUC levels. Our results indicate that both MODIS ET products effectively reproduced basin scale ET response (up to 25% uncertainty) compared to CONUS-wide point-based ET response (up to 50–60% uncertainty) illustrating the reliability of MODIS ET products for basin-scale ET estimation. Results from this research would guide the additional parameter refinement required for the MOD16 and SSEBop algorithms in order to further improve their accuracy and performance for agro-hydrologic applications.

CompNanoTox2015: novel perspectives from a European conference on computational nanotoxicology on predictive nanotoxicology.

PubMed

Bañares, Miguel A; Haase, Andrea; Tran, Lang; Lobaskin, Vladimir; Oberdörster, Günter; Rallo, Robert; Leszczynski, Jerzy; Hoet, Peter; Korenstein, Rafi; Hardy, Barry; Puzyn, Tomasz

2017-09-01

A first European Conference on Computational Nanotoxicology, CompNanoTox, was held in November 2015 in Benahavís, Spain with the objectives to disseminate and integrate results from the European modeling and database projects (NanoPUZZLES, ModENPTox, PreNanoTox, MembraneNanoPart, MODERN, eNanoMapper and EU COST TD1204 MODENA) as well as to create synergies within the European NanoSafety Cluster. This conference was supported by the COST Action TD1204 MODENA on developing computational methods for toxicological risk assessment of engineered nanoparticles and provided a unique opportunity for cross fertilization among complementary disciplines. The efforts to develop and validate computational models crucially depend on high quality experimental data and relevant assays which will be the basis to identify relevant descriptors. The ambitious overarching goal of this conference was to promote predictive nanotoxicology, which can only be achieved by a close collaboration between the computational scientists (e.g. database experts, modeling experts for structure, (eco) toxicological effects, performance and interaction of nanomaterials) and experimentalists from different areas (in particular toxicologists, biologists, chemists and material scientists, among others). The main outcome and new perspectives of this conference are summarized here.

CompNanoTox2015: novel perspectives from a European conference on computational nanotoxicology on predictive nanotoxicology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bañares, Miguel A.; Haase, Andrea; Tran, Lang

A first European Conference on Computational Nanotoxicology, CompNanoTox, was held in November 2015 in Benahavís, Spain with the objectives to disseminate and integrate results from the European modeling and database projects (NanoPUZZLES, ModENPTox, PreNanoTox, MembraneNanoPart, MODERN, eNanoMapper and EU COST TD1204 MODENA) as well as to create synergies within the European NanoSafety Cluster. This conference was supported by the COST Action TD1204 MODENA on developing computational methods for toxicological risk assessment of engineered nanoparticles and provided a unique opportunity for crossfertilization among complementary disciplines. The efforts to develop and validate computational models crucially depend on high quality experimental data andmore » relevant assays which will be the basis to identify relevant descriptors. The ambitious overarching goal of this conference was to promote predictive nanotoxicology, which can only be achieved by a close collaboration between the computational scientists (e.g. database experts, modeling experts for structure, (eco) toxicological effects, performance and interaction of nanomaterials) and experimentalists from different areas (in particular toxicologists, biologists, chemists and material scientists, among others). The main outcome and new perspectives of this conference are summarized here.« less

Exploring the Relationships between Self-Efficacy and Preference for Teacher Authority among Computer Science Majors

ERIC Educational Resources Information Center

Lin, Che-Li; Liang, Jyh-Chong; Su, Yi-Ching; Tsai, Chin-Chung

2013-01-01

Teacher-centered instruction has been widely adopted in college computer science classrooms and has some benefits in training computer science undergraduates. Meanwhile, student-centered contexts have been advocated to promote computer science education. How computer science learners respond to or prefer the two types of teacher authority,…

Nitrogen utilization, preweaning nutrient digestibility, and growth effects of Holstein dairy calves fed 2 amounts of a moderately high protein or conventional milk replacer.

PubMed

Chapman, C E; Hill, T M; Elder, D R; Erickson, P S

2017-01-01

Studies have shown that calves fed milk replacers (MR) with crude protein (CP) concentrations greater than 20%, as typically found in conventional MR, have higher dry matter intakes (DMI) and greater average daily gains (ADG) but consume less starter, which can lead to stress during weaning and reduced rumen development. The greater amount of CP being fed to preweaned calves may alter their nitrogen (N) balance, and excess N may be excreted in the urine. The objective of this study was to determine N utilization in preweaned calves fed diets varying in the amount of CP and MR fed. This study used 24 newborn dairy heifer calves blocked by birth and randomly assigned to 1 of 3 treatments: (1) 446g dry matter (DM) of a conventional MR (CON; 20% CP, 20% fat), (2) 669g DM of a moderately high protein MR (moderate; MOD; 26% CP, 18% fat), or (3) 892g DM of a moderately high protein MR (aggressive; AGG; 26% CP, 18% fat). All calves had ad libitum access to starter and water. Both MR and starter were medicated with decoquinate. During weaning (d 43-49), the morning MR feeding ceased. On d 50, all MR feedings ended; however, starter and water intakes were continuously recorded until d 56. At 5wk of age, urine was collected using urinary catheters for 3d and chromium oxide was administered by bolus at 2g/d for 7d to estimate N efficiency. Calves fed MOD and AGG had similar starter intakes, feed efficiencies, and ADG, with the combined treatments having reduced starter intakes (258 vs. 537g/d), greater ADG (674 vs. 422g/d), and improved feed efficiency (0.57 vs. 0.45 gain:feed) compared with CON calves preweaning. However, DMI and water intake were similar across all treatments. Results from the N utilization phase showed that MOD and AGG treatments had similar but lower N efficiency compared with CON calves (45.5 vs. 52.7%). This could be due to MOD- and AGG-fed calves having greater urine volume and thereby, greater combined urine N output compared with CON calves (17.6 vs. 12.1 g/d). In summary, feeding >0.66kg (DM) from a 26% CP MR increased ADG and improved feed efficiency during the preweaning period but reduced starter intake and lowered N efficiency. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Mod-5A wind turbine generator program design report. Volume 4: Drawings and specifications, book 4

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator are documented. There are four volumes. This volume contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. This volume contains 5 books of which this is the fourth, providing drawings 47A380128 through 47A387125. In addition to the parts listing and where-used list, the logic design of the controller software and the code listing of the controller software are provided. Also given are the aerodynamic profile coordinates.

Mod-5A wind turbine generator program design report. Volume 4: Drawings and specifications, book 2

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. There are four volumes. This volume contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. This is the second book of volume four. Some of the items it contains are specs for the emergency shutdown panel, specs for the simulator software, simulator hardware specs, site operator terminal requirements, control data system requirements, software project management plan, elastomeric teeter bearing requirement specs, specs for the controls electronic cabinet, and specs for bolt pretensioning.

78 FR 36633 - National Automotive Sampling System

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-18

... System (NASS) or Data Modernization (DataMod). NHTSA announces that it will hold a public listening session to solicit information and comments on: (a) Adding, deleting or changing the current NASS data elements for DataMod, and; (b) recommendations for changing or improving the NASS data collection...

78 FR 48286 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-08

... installed on both LH and RH sides (Airbus modification 153655 applied in production, or modified in-service... unit (LGCIU) interlink communication ARINC 429 (applied in production through Airbus Modification (mod... of MLG actuator Part Number (P/N) 114122014 through Airbus SB A320-32-1407 (Airbus production mod...

Integrated Micro-Chip Amino Acid Chirality Detector for MOD

NASA Technical Reports Server (NTRS)

Glavin, D. P.; Bada, J. L.; Botta, O.; Kminek, G.; Grunthaner, F.; Mathies, R.

2001-01-01

Integration of a micro-chip capillary electrophoresis analyzer with a sublimation-based extraction technique, as used in the Mars Organic Detector (MOD), for the in-situ detection of amino acids and their enantiomers on solar system bodies. Additional information is contained in the original extended abstract.

The challenges of numerically simulating analogue brittle thrust wedges

NASA Astrophysics Data System (ADS)

Buiter, Susanne; Ellis, Susan

2017-04-01

Fold-and-thrust belts and accretionary wedges form when sedimentary and crustal rocks are compressed into thrusts and folds in the foreland of an orogen or at a subduction trench. For over a century, analogue models have been used to investigate the deformation characteristics of such brittle wedges. These models predict wedge shapes that agree with analytical critical taper theory and internal deformation structures that well resemble natural observations. In a series of comparison experiments for thrust wedges, called the GeoMod2004 (1,2) and GeoMod2008 (3,4) experiments, it was shown that different numerical solution methods successfully reproduce sandbox thrust wedges. However, the GeoMod2008 benchmark also pointed to the difficulties of representing frictional boundary conditions and sharp velocity discontinuities with continuum numerical methods, in addition to the well-known challenges of numerical plasticity. Here we show how details in the numerical implementation of boundary conditions can substantially impact numerical wedge deformation. We consider experiment 1 of the GeoMod2008 brittle thrust wedge benchmarks. This experiment examines a triangular thrust wedge in the stable field of critical taper theory that should remain stable, that is, without internal deformation, when sliding over a basal frictional surface. The thrust wedge is translated by lateral displacement of a rigid mobile wall. The corner between the mobile wall and the subsurface is a velocity discontinuity. Using our finite-element code SULEC, we show how different approaches to implementing boundary friction (boundary layer or contact elements) and the velocity discontinuity (various smoothing schemes) can cause the wedge to indeed translate in a stable manner or to undergo internal deformation (which is a fail). We recommend that numerical studies of sandbox setups not only report the details of their implementation of boundary conditions, but also document the modelling attempts that failed. References 1. Buiter and the GeoMod2004 Team, 2006. The numerical sandbox: comparison of model results for a shortening and an extension experiment. Geol. Soc. Lond. Spec. Publ. 253, 29-64 2. Schreurs and the GeoMod2004 Team, 2006. Analogue benchmarks of shortening and extension experiments. Geol. Soc. Lond. Spec. Publ. 253, 1-27 3. Buiter, Schreurs and the GeoMod2008 Team, 2016. Benchmarking numerical models of brittle thrust wedges, J. Struct. Geol. 92, 140-177 4. Schreurs, Buiter and the GeoMod2008 Team, 2016. Benchmarking analogue models of brittle thrust wedges, J. Struct. Geol. 92, 116-13

Microscopic-observation drug susceptibility and thin layer agar assays for the detection of drug resistant tuberculosis: a systematic review and meta-analysis.

PubMed

Minion, Jessica; Leung, Erika; Menzies, Dick; Pai, Madhukar

2010-10-01

Simple, rapid, and affordable tests are needed to detect drug resistance in Mycobacterium tuberculosis. We did a systematic review and meta-analysis to investigate the accuracy of microscopic-observation drug susceptibility (MODS) and thin layer agar (TLA) assays for rapid screening of patients at risk of drug-resistant tuberculosis. In accordance with protocols and methods recommended by the Cochrane Diagnostic Test Accuracy Working Group, we systematically searched PubMed, Embase, and Biosis for reports published between January, 1990, and February, 2009. We included studies investigating detection of drug resistance in M tuberculosis with the MODS or TLA assay, and in which an accepted reference standard was used. Data extracted from the studies were combined by use of bivariate random-effects regression models and hierarchical summary receiver operating characteristic curves to estimate sensitivity and specificity for detection of resistance to specific drugs. We identified 12 studies, of which nine investigated the MODS assay and three investigated the TLA assay. For the MODS assay of rifampicin resistance, pooled estimates were 98·0% (95% CI 94·5-99·3) for sensitivity and 99·4% (95·7-99·9) for specificity. For the MODS assay of isoniazid resistance with a 0·1 μg/mL cutoff, pooled sensitivity was 97·7% (94·4-99·1) and pooled specificity was 95·8% (88·1-98·6), but with a 0·4 μg/mL cutoff, sensitivity decreased to 90·0% (84·5-93·7) and specificity increased to 98·6% (96·9-99·4). All assessments of rifampicin and isoniazid resistance with the TLA assay yielded 100% accuracy. Mean turnaround time was 9·9 days (95% CI 4·1-15·8) for the MODS assay and 11·1 days (10·1-12·0) for the TLA assay. MODS and TLA assays are inexpensive, rapid alternatives to conventional methods for drug susceptibility testing of M tuberculosis. Our data and expert opinion informed WHO's recommendation for use of selected non-commercial drug susceptibility tests, including MODS, as an interim solution until capacity for genotypic or automated liquid culture drug susceptibility testing is developed. Stop TB Department of WHO. Copyright © 2010 Elsevier Ltd. All rights reserved.

Academic computer science and gender: A naturalistic study investigating the causes of attrition

NASA Astrophysics Data System (ADS)

Declue, Timothy Hall

Far fewer women than men take computer science classes in high school, enroll in computer science programs in college, or complete advanced degrees in computer science. The computer science pipeline begins to shrink for women even before entering college, but it is at the college level that the "brain drain" is the most evident numerically, especially in the first class taken by most computer science majors called "Computer Science 1" or CS-I. The result, for both academia and industry, is a pronounced technological gender disparity in academic and industrial computer science. The study revealed the existence of several factors influencing success in CS-I. First, and most clearly, the effect of attribution processes seemed to be quite strong. These processes tend to work against success for females and in favor of success for males. Likewise, evidence was discovered which strengthens theories related to prior experience and the perception that computer science has a culture which is hostile to females. Two unanticipated themes related to the motivation and persistence of successful computer science majors. The findings did not support the belief that females have greater logistical problems in computer science than males, or that females tend to have a different programming style than males which adversely affects the females' ability to succeed in CS-I.

Assessment of Fetal Myocardial Performance Index in Women with Placenta Previa

PubMed Central

Zhang, Na; Sun, Lijuan; Zhang, Lina; Li, Zhen; Han, Jijing; Wu, Qingqing

2017-01-01

Background This study investigated whether fetuses of placenta previa pregnancies have cardiac dysfunction by use of a modified myocardial performance index (Mod-MPI). Material/Methods A prospective cross-sectional study was conducted including 178 fetuses at 28–40 weeks of gestation. Eighty-nine fetuses of mothers with placenta previa and without pregnancy complications were recruited (placenta previa group) and matched with 89 fetuses of mothers with normal pregnancies (control group). Fetal cardiac function parameters and perinatal outcomes as well as the Mod-MPI were compared between the 2 groups. Results The median Mod-MPI was significantly increased in fetuses of mothers with placenta previa compared with controls (0.47±0.05 vs. 0.45±0.05; P<0.01). Among fetuses of mothers with or without placenta previa, the Mod-MPI was significantly higher in the incomplete placenta previa group compared with the complete placenta previa group and control group (P<0.01). An increased Mod-MPI in placenta previa pregnancies was independently associated with fetal cord pH <7.2 (odds ratio, 4.8; 95% confidence interval, 0.98–23.54; P=0.003). Conclusions There is impairment of fetal cardiac function in pregnancies with placenta previa. An increased MPI was independently associated with adverse perinatal outcomes to some extent in the placenta previa pregnancies. PMID:29242496

Reliability of the MODS assay decentralisation process in three health regions in Peru

PubMed Central

Mendoza, A.; Castillo, E.; Gamarra, N.; Huamán, T.; Perea, M.; Monroi, Y.; Salazar, R.; Coronel, J.; Acurio, M.; Obregón, G.; Roper, M.; Bonilla, C.; Asencios, L.; Moore, D. A. J.

2011-01-01

OBJECTIVE To deliver rapid isoniazid (INH) and rifampicin (RMP) drug susceptibility testing (DST) close to the patient, we designed a decentralisation process for the microscopic observation drug susceptibility (MODS) assay in Peru and evaluated its reliability. METHODS After 2 weeks of training, laboratory staff processed ≥120 consecutive sputum samples each in three regional laboratories. Samples were processed in parallel with MODS testing at an expert laboratory. Blinded paired results were independently analysed by the Instituto Nacional de Salud (INS) according to predetermined criteria: concordance for culture, DST against INH and RMP and diagnosis of multidrug-resistant t uberculosis (MDR-TB) ≥ 95%, McNemar's P > 0.05, kappa index (κ) ≥ 0.75 and contamination 1–4%. Sensitivity and specificity for MDR-TB were calculated. RESULTS The accreditation process for Callao (126 samples, 79.4% smear-positive), Lima Sur (n = 130, 84%) and Arequipa (n = 126, 80%) took respectively 94, 97 and 173 days. Pre-determined criteria in all regional laboratories were above expected values. The sensitivity and specificity for detecting MDR-TB in regional laboratories were >95%, except for sensitivity in Lima Sur, which was 91.7%. Contamination was 1.0–2.3%. Mean delay to positive MODS results was 9.9–12.9 days. CONCLUSION Technology transfer of MODS was reliable, effective and fast, enabling the INS to accredit regional laboratories swiftly. PMID:21219684

Serum cytochrome c level as a prognostic indicator in patients with systemic inflammatory response syndrome.

PubMed

Adachi, Naoto; Hirota, Masahiko; Hamaguchi, Masamichi; Okamoto, Kazufumi; Watanabe, Keisuke; Endo, Fumio

2004-04-01

Apoptosis may play an important role in the development of systemic inflammatory response syndrome (SIRS) and progression to multiple organ dysfunction syndrome (MODS). To quantify the extent of apoptosis in these morbidities, we developed a sandwich ELISA system to measure serum cytochrome c (cyt-c) levels and we investigated the prognostic significance of cyt-c concentration in SIRS/MODS patients. Cyt-c concentrations in patients with SIRS (n=53) with or at risk for MODS were measured and compared with those of control subjects (n=14). Cyt-c concentrations in SIRS/MODS patients increased (0.24-210 ng/ml), whereas those in control subjects were under detection limits (0.1 ng/ml). Cyt-c concentrations in non-survivors increased significantly compared with those in survivors both on the day of admission and on the fifth hospital day. A significant positive correlation was found between cyt-c concentration and two representative organ dysfunction scores, APACHE II and multi-organ failure (MOF) score. Cyt-c concentrations increased earlier than MOF score during the exacerbation phase and rapidly decreased during the convalescence phase in a survivor, but the level continued to be high in a non-survivor. Determination of serum cyt-c concentrations may be useful to assess the severity of organ dysfunction and to predict the prognosis of SIRS/MODS patients.

Modélisation de matériaux chiraux à structures hétérogènes (modèle MTWC) : théorie, validations expérimentales et applications

NASA Astrophysics Data System (ADS)

Mariotte, F.; Sauviac, B.; Héliot, J. Ph.

1995-10-01

After a brief overview of the concept of electromagnetic chirality, this paper deals with a numerical simulation of isotropic composites with metallic chiral inclusions: computations of permittivity, permeability and chirality parameter as functions of frequency are presented. The theoretical results are, step by step, compared with measurements of chiral composites at microwave frequencies. The application of such media in Radar Cross-Section (RCS) management and control is discussed. The introduction of chiral inclusions seems to make impedance matching possible and may lead to attractive shields with lower reflectivity and larger bandwidth. However the optimization of material characteristics necessary to get a specific absorber remains a difficult task. Après un bref rappel du principe de la chiralité, cet article présente une modélisation des propriétés effectives des matériaux hétérogènes à inclusions chirales métalliques : calcul de la permittivité, perméabilité et coefficient de chiralité du composite en fonction de la fréquence. Les résultats théoriques sont validés, pas à pas, par des mesures effectuées sur des composites chiraux de natures différentes. L'application de tels matériaux à la conception de matériaux absorbant les ondes électromagnétiques est ensuite envisagée. Les inclusions chirales semblent offrir la possibilité de régler l'impédance à l'interface air-milieu absorbant permettant ainsi de concevoir des absorbants micro-ondes plus performants en terme d'atténuation ou de largeur de bande. L'optimisation des caractéristiques des matériaux pour obtenir des performances données restent néanmoins très délicate.

Computer-Game Construction: A Gender-Neutral Attractor to Computing Science

ERIC Educational Resources Information Center

Carbonaro, Mike; Szafron, Duane; Cutumisu, Maria; Schaeffer, Jonathan

2010-01-01

Enrollment in Computing Science university programs is at a dangerously low level. A major reason for this is the general lack of interest in Computing Science by females. In this paper, we discuss our experience with using a computer game construction environment as a vehicle to encourage female participation in Computing Science. Experiments…

FlexMod Scheduling Redux

ERIC Educational Resources Information Center

Murray, Shannon

2008-01-01

Flexible modular scheduling (flex mod)--a schedule philosophy and system that has been in place at Wausau West High School in Wausau, Wisconsin, for the last 35 years and aligns nicely with current research on student learning--is getting more and more attention from high school administrators across the country. Flexible modular scheduling was…

78 FR 58492 - Generator Verification Reliability Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-24

... Control Functions), MOD-027-1 (Verification of Models and Data for Turbine/Governor and Load Control or...), MOD-027-1 (Verification of Models and Data for Turbine/Governor and Load Control or Active Power... Category B and C contingencies, as required by wind generators in Order No. 661, or that those generators...

Idempotents a la mod

ERIC Educational Resources Information Center

Sibley, Thomas Q.

2012-01-01

An idempotent satisfies the equation x[superscript 2] = x. In ordinary arithmetic, this is so easy to solve it's boring. We delight the mathematical palette here, topping idempotents off with modular arithmetic and a series of exercises determining for which n there are more than two idempotents (mod n) and exactly how many there are.

Central Computer Science Concepts to Research-Based Teacher Training in Computer Science: An Experimental Study

ERIC Educational Resources Information Center

Zendler, Andreas; Klaudt, Dieter

2012-01-01

The significance of computer science for economics and society is undisputed. In particular, computer science is acknowledged to play a key role in schools (e.g., by opening multiple career paths). The provision of effective computer science education in schools is dependent on teachers who are able to properly represent the discipline and whose…

The affine cohomology spaces and its applications

NASA Astrophysics Data System (ADS)

Fraj, Nizar Ben; Laraiedh, Ismail

2016-12-01

We compute the nth cohomology space of the affine Lie superalgebra 𝔞𝔣𝔣(1) on the (1,1)-dimensional real superspace with coefficient in a large class of 𝔞𝔣𝔣(1)-modules M. We apply our results to the module of weight densities and the module of linear differential operators acting on a superspace of weighted densities. This work is the generalization of a result by Basdouri et al. [The linear 𝔞𝔣𝔣(n|1)-invariant differential operators on weighted densities on the superspace ℝ1|n and 𝔞𝔣𝔣(n|1)-relative cohomology, Int. J. Geom. Meth. Mod. Phys. 10 (2013), Article ID: 1320004, 9 pp.

The conceptualization model problem—surprise

NASA Astrophysics Data System (ADS)

Bredehoeft, John

2005-03-01

The foundation of model analysis is the conceptual model. Surprise is defined as new data that renders the prevailing conceptual model invalid; as defined here it represents a paradigm shift. Limited empirical data indicate that surprises occur in 20-30% of model analyses. These data suggest that groundwater analysts have difficulty selecting the appropriate conceptual model. There is no ready remedy to the conceptual model problem other than (1) to collect as much data as is feasible, using all applicable methods—a complementary data collection methodology can lead to new information that changes the prevailing conceptual model, and (2) for the analyst to remain open to the fact that the conceptual model can change dramatically as more information is collected. In the final analysis, the hydrogeologist makes a subjective decision on the appropriate conceptual model. The conceptualization problem does not render models unusable. The problem introduces an uncertainty that often is not widely recognized. Conceptual model uncertainty is exacerbated in making long-term predictions of system performance. C'est le modèle conceptuel qui se trouve à base d'une analyse sur un modèle. On considère comme une surprise lorsque le modèle est invalidé par des données nouvelles; dans les termes définis ici la surprise est équivalente à un change de paradigme. Des données empiriques limitées indiquent que les surprises apparaissent dans 20 à 30% des analyses effectuées sur les modèles. Ces données suggèrent que l'analyse des eaux souterraines présente des difficultés lorsqu'il s'agit de choisir le modèle conceptuel approprié. Il n'existe pas un autre remède au problème du modèle conceptuel que: (1) rassembler autant des données que possible en utilisant toutes les méthodes applicables—la méthode des données complémentaires peut conduire aux nouvelles informations qui vont changer le modèle conceptuel, et (2) l'analyste doit rester ouvert au fait que le modèle conceptuel peut bien changer lorsque des nouvelles informations apparaissent. Dans l'analyse finale le hydrogéologue prend une décision subjective sur le modèle conceptuel approprié. Le problème du le modèle conceptuel ne doit pas rendre le modèle inutilisable. Ce problème introduit une incertitude qui n'est pas toujours reconnue. Les incertitudes du modèle conceptuel deviennent plus importantes dans les cases de prévisions à long terme dans l'analyse de performance. La base para hacer un análisis de un modelo es el modelo conceptual. Se define aquí la sorpresa como los datos nuevos que convierten en incoherente al modelo conceptual previamente aceptado; tal como se define aquí esto representa un cambio de paradigma. Los datos empíricos limitados indican que estas sorpresas suceden entre un 20 a un 30% de los análisis de modelos. Esto sugiere que los analistas de modelos de agua subterránea tienen dificultades al seleccionar el modelo conceptual apropiado. No hayotra solución disponible a este problema del modelo conceptual diferente de: (1) Recolectar tanta información como sea posible, mediante la utilización de todos los métodos aplicables, lo cual puede resultar en que esta nueva información ayude a cambiar el modelo conceptual vigente, y (2) Que el analista de modelos se mantenga siempre abierto al hecho de que un modelo conceptual puede cambiar de manera total, en la medida en que se colecte mas información. En el análisis final el hidrogeólogo toma una decisión subjetiva en cuanto al modelo conceptual apropiado. El problema de la conceptualización no produce modelos inútiles. El problema presenta una incertidumbre, la cual a menudo no es tenida en cuentade manera adecuada. Esta incertidumbre en los modelos conceptuales se aumenta, cuando se hacen predicciones a largo plazo del comportamiento de un sistema dado.

Using spatial principles to optimize distributed computing for enabling the physical science discoveries

PubMed Central

Yang, Chaowei; Wu, Huayi; Huang, Qunying; Li, Zhenlong; Li, Jing

2011-01-01

Contemporary physical science studies rely on the effective analyses of geographically dispersed spatial data and simulations of physical phenomena. Single computers and generic high-end computing are not sufficient to process the data for complex physical science analysis and simulations, which can be successfully supported only through distributed computing, best optimized through the application of spatial principles. Spatial computing, the computing aspect of a spatial cyberinfrastructure, refers to a computing paradigm that utilizes spatial principles to optimize distributed computers to catalyze advancements in the physical sciences. Spatial principles govern the interactions between scientific parameters across space and time by providing the spatial connections and constraints to drive the progression of the phenomena. Therefore, spatial computing studies could better position us to leverage spatial principles in simulating physical phenomena and, by extension, advance the physical sciences. Using geospatial science as an example, this paper illustrates through three research examples how spatial computing could (i) enable data intensive science with efficient data/services search, access, and utilization, (ii) facilitate physical science studies with enabling high-performance computing capabilities, and (iii) empower scientists with multidimensional visualization tools to understand observations and simulations. The research examples demonstrate that spatial computing is of critical importance to design computing methods to catalyze physical science studies with better data access, phenomena simulation, and analytical visualization. We envision that spatial computing will become a core technology that drives fundamental physical science advancements in the 21st century. PMID:21444779

Using spatial principles to optimize distributed computing for enabling the physical science discoveries.

PubMed

Yang, Chaowei; Wu, Huayi; Huang, Qunying; Li, Zhenlong; Li, Jing

2011-04-05

Contemporary physical science studies rely on the effective analyses of geographically dispersed spatial data and simulations of physical phenomena. Single computers and generic high-end computing are not sufficient to process the data for complex physical science analysis and simulations, which can be successfully supported only through distributed computing, best optimized through the application of spatial principles. Spatial computing, the computing aspect of a spatial cyberinfrastructure, refers to a computing paradigm that utilizes spatial principles to optimize distributed computers to catalyze advancements in the physical sciences. Spatial principles govern the interactions between scientific parameters across space and time by providing the spatial connections and constraints to drive the progression of the phenomena. Therefore, spatial computing studies could better position us to leverage spatial principles in simulating physical phenomena and, by extension, advance the physical sciences. Using geospatial science as an example, this paper illustrates through three research examples how spatial computing could (i) enable data intensive science with efficient data/services search, access, and utilization, (ii) facilitate physical science studies with enabling high-performance computing capabilities, and (iii) empower scientists with multidimensional visualization tools to understand observations and simulations. The research examples demonstrate that spatial computing is of critical importance to design computing methods to catalyze physical science studies with better data access, phenomena simulation, and analytical visualization. We envision that spatial computing will become a core technology that drives fundamental physical science advancements in the 21st century.

A Financial Technology Entrepreneurship Program for Computer Science Students

ERIC Educational Resources Information Center

Lawler, James P.; Joseph, Anthony

2011-01-01

Education in entrepreneurship is becoming a critical area of curricula for computer science students. Few schools of computer science have a concentration in entrepreneurship in the computing curricula. The paper presents Technology Entrepreneurship in the curricula at a leading school of computer science and information systems, in which students…

Computer Science Teacher Professional Development in the United States: A Review of Studies Published between 2004 and 2014

ERIC Educational Resources Information Center

Menekse, Muhsin

2015-01-01

While there has been a remarkable interest to make computer science a core K-12 academic subject in the United States, there is a shortage of K-12 computer science teachers to successfully implement computer sciences courses in schools. In order to enhance computer science teacher capacity, training programs have been offered through teacher…

Automotive Stirling engine: Mod 2 design report

NASA Technical Reports Server (NTRS)

Nightingale, Noel P.

1986-01-01

The design of an automotive Stirling engine that achieves the superior fuel economy potential of the Stirling cycle is described. As the culmination of a 9-yr development program, this engine, designated the Mod 2, also nullifies arguments that Stirling engines are heavy, expensive, unreliable, demonstrating poor performance. Installed in a General Motors Chevrolet Celebrity car, this engine has a predicted combined fuel economy on unleaded gasoline of 17.5 km/l (41 mpg)- a value 50% above the current vehicle fleet average. The Mod 2 Stirling engine is a four-cylinder V-drive design with a single crankshaft. The engine is also equipped with all the controls and auxiliaries necessary for automotive operation.

GeoMod 2014 - Modelling in geoscience

NASA Astrophysics Data System (ADS)

Leever, Karen; Oncken, Onno

2016-08-01

GeoMod is a biennial conference to review and discuss latest developments in analogue and numerical modelling of lithospheric and mantle deformation. GeoMod2014 took place at the GFZ German Research Centre for Geosciences in Potsdam, Germany. Its focus was on rheology and deformation at a wide range of temporal and spatial scales: from earthquakes to long-term deformation, from micro-structures to orogens and subduction systems. It also addressed volcanotectonics and the interaction between tectonics and surface processes (Elger et al., 2014). The conference was followed by a 2-day short course on "Constitutive Laws: from Observation to Implementation in Models" and a 1-day hands-on tutorial on the ASPECT numerical modelling software.

Automotive Stirling Engine Development Program Mod I Stirling engine development

NASA Technical Reports Server (NTRS)

Simetkosky, M. A.

1983-01-01

The development of the Mod I 4-cylinder automotive Stirling engine is discussed and illustrated with drawings, block diagrams, photographs, and graphs and tables of preliminary test data. The engine and its drive, cold-engine, hot-engine, external-heat, air/fuel, power-control, electronic-control, and auxiliary systems are characterized. Performance results from a total of 1900 h of tests on 4 prototype engines include average maximum efficiency (at 2000 rpm) 34.5 percent and maximum output power 54.4 kW. The modifications introduced in an upgraded version of the Mod I are explained; this engine has maximum efficiency 40.4 percent and maximum power output 69.2 kW.

The NASA-LeRC wind turbine sound prediction code

NASA Technical Reports Server (NTRS)

Viterna, L. A.

1981-01-01

Development of the wind turbine sound prediction code began as part of an effort understand and reduce the noise generated by Mod-1. Tone sound levels predicted with this code are in good agreement with measured data taken in the vicinity Mod-1 wind turbine (less than 2 rotor diameters). Comparison in the far field indicates that propagation effects due to terrain and atmospheric conditions may amplify the actual sound levels by 6 dB. Parametric analysis using the code shows that the predominant contributors to Mod-1 rotor noise are (1) the velocity deficit in the wake of the support tower, (2) the high rotor speed, and (3) off-optimum operation.

Development of a Dynamic Biomechanical Model for Load Carriage: Phase V: Development of the Biomechanical Model by Means of the Portable Measurement System

DTIC Science & Technology

2005-05-01

Résumé La performance opérationnelle des soldats dépend d’un certain nombre de facteurs, dont la charge de travail physiologique, les effets ...particulièrement à la charge de travail physiologique et aux effets biomécaniques, et à perfectionner la mise au point d’un modèle biomécanique dynamique (DBM...on a créé une couche de peau possédant des propriétés appropriées pour le modèle de torse et on a réalisé la modélisation de tous les composants

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

1986-01-01

This is the ninth Semiannual Technical Progress Report prepared under the Automotive Stirling Engine Development Program. It covers the twenty-eighth and twenty-ninth quarters of activity after award of the contract. Quarterly Technical Progress Reports related program activities from the first through the thirteenth quarters; thereafter, reporting was changed to a Semiannual format. This report summarizes the study of higher-power kinematic Stirling engines for transportation use, development testing of Mod I Stirling engines, and component development activities. Component development testing included successful conical fuel nozzle testing and functional checkout of Mod II controls and auxiliaries on Mod I engine test beds. Overall program philosophy is outlined and data and test results are presented.

The Mod-2 wind turbine development project

NASA Technical Reports Server (NTRS)

Linscott, B. S.; Dennett, J. T.; Gordon, L. H.

1981-01-01

A major phase of the Federal Wind Energy Program, the Mod-2 wind turbine, a second-generation machine developed by the Boeing Engineering and Construction Co. for the U.S. Department of Energy and the Lewis Research Center of the National Aeronautics and Space Administration, is described. The Mod-2 is a large (2.5-MW power rating) horizontal-axis wind turbine designed for the generation of electrical power on utility networks. Three machines were built and are located in a cluster at Goodnoe Hills, Washington. All technical aspects of the project are described: design approach, significant innovation features, the mechanical system, the electrical power system, the control system, and the safety system.

ALCBEAM - Neutral beam formation and propagation code for beam-based plasma diagnostics

NASA Astrophysics Data System (ADS)

Bespamyatnov, I. O.; Rowan, W. L.; Liao, K. T.

2012-03-01

ALCBEAM is a new three-dimensional neutral beam formation and propagation code. It was developed to support the beam-based diagnostics installed on the Alcator C-Mod tokamak. The purpose of the code is to provide reliable estimates of the local beam equilibrium parameters: such as beam energy fractions, density profiles and excitation populations. The code effectively unifies the ion beam formation, extraction and neutralization processes with beam attenuation and excitation in plasma and neutral gas and beam stopping by the beam apertures. This paper describes the physical processes interpreted and utilized by the code, along with exploited computational methods. The description is concluded by an example simulation of beam penetration into plasma of Alcator C-Mod. The code is successfully being used in Alcator C-Mod tokamak and expected to be valuable in the support of beam-based diagnostics in most other tokamak environments. Program summaryProgram title: ALCBEAM Catalogue identifier: AEKU_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEKU_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 66 459 No. of bytes in distributed program, including test data, etc.: 7 841 051 Distribution format: tar.gz Programming language: IDL Computer: Workstation, PC Operating system: Linux RAM: 1 GB Classification: 19.2 Nature of problem: Neutral beams are commonly used to heat and/or diagnose high-temperature magnetically-confined laboratory plasmas. An accurate neutral beam characterization is required for beam-based measurements of plasma properties. Beam parameters such as density distribution, energy composition, and atomic excited populations of the beam atoms need to be known. Solution method: A neutral beam is initially formed as an ion beam which is extracted from the ion source by high voltage applied to the extraction and accelerating grids. The current distribution of a single beamlet emitted from a single pore of IOS depends on the shape of the plasma boundary in the emission region. Total beam extracted by IOS is calculated at every point of 3D mesh as sum of all contributions from each grid pore. The code effectively unifies the ion beam formation, extraction and neutralization processes with neutral beam attenuation and excitation in plasma and neutral gas and beam stopping by the beam apertures. Running time: 10 min for a standard run.

Computer Science | Classification | College of Engineering & Applied

Science.gov Websites

EMS 1011 profile photo Adrian Dumitrescu, Ph.D.ProfessorComputer Science(414) 229-4265Eng & Math @uwm.eduEng & Math Sciences 919 profile photo Hossein Hosseini, Ph.D.ProfessorComputer Science(414) 229 -5184hosseini@uwm.eduEng & Math Sciences 1091 profile photo Amol Mali, Ph.D.Associate ProfessorComputer

Computers in Science Education: Can They Go Far Enough? Have We Gone Too Far?

ERIC Educational Resources Information Center

Schrock, John Richard

1984-01-01

Indicates that although computers may churn out creative research, science is still dependent on science education, and that science education consists of increasing human experience. Also considers uses and misuses of computers in the science classroom, examining Edgar Dale's "cone of experience" related to laboratory computer and "extended…

Service Children's Education: Survey of Parental Views. Final Report

ERIC Educational Resources Information Center

O'Donnell, Lisa; Rudd, Peter

2007-01-01

Service Children's Education (SCE) is an agency of the Ministry of Defence (MOD) that is dedicated to the education of children of service families and MOD personnel serving outside of the United Kingdom, specifically in Belgium, Germany, Italy, The Netherlands, Cyprus, Gibraltar, Falkland Islands, Belize and Brunei. These schools follow the…

75 FR 26057 - Mandatory Reliability Standards for the Calculation of Available Transfer Capability, Capacity...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-11

... Requirement R3.1 of MOD-001-1. C. Benchmarking 14. In the Final Rule, the Commission directed the ERO to develop benchmarking and updating requirements for the MOD Reliability Standards to measure modeled... requirements should specify the frequency for benchmarking and updating the available transfer and flowgate...

OHD/HL/HSEB - MODS

Science.gov Websites

1201200612z star date and time; when the modified observed precipitation starts (inclusive) 1202200612z end date and time; when the modified observed precipitation ends (non-inclusive) 1205200612z valid date and time; when the mod expires 2.0 the muliplier used to adjust the observed precip (i.e. values less than

Mod-1 wind turbine generator analysis and design report, volume 1

NASA Technical Reports Server (NTRS)

1979-01-01

The activities leading to the completion of detail design of the MOD-1 wind turbine generator are described. Emphasis is placed on the description of the design as it finally evolved. However, the steps through which the design progressed are also traced in order to understand the major design decisions.

Site Data Acquisition Subsystem (SDAS) Mod 1, installation, operation, and maintenance manual

NASA Technical Reports Server (NTRS)

1977-01-01

The Site Data Acquisition Subsystem (SDAS) Mod 1 was designed to collect sensor measurement data from solar energy demonstration site. This report provides a brief description of the SDAS and defines the installation requirements and procedures, the operations description and the procedures for field maintenance of the subsystem.

Pedestal turbulence simulations using GENE

NASA Astrophysics Data System (ADS)

Liu, Xing; Kotschenreuther, M.; Hatch, D. R.; Zheng, L. J.; Mahajan, S.; Diallo, A.; Groebner, R. J.; Hubbard, A. E.; Hughes, J. W.; Maggi, C. F.; Saarelma, S.; JET Contributors

2017-10-01

We match frequencies, power balance, and other transport characteristics of several pedestals-two DIIID ELMy H-modes and a C-Mod I-mode, and attempt this for a C-Mod ELMy H-mode. Observed quasi-coherent fluctuations (QCFs) on the DIIID shots are identified as MTMs. The MTMs match frequency and power balance (with slight adjustment of temperature profile), and cause low transport in the density, ion heat and impurity channels- consistent with observed inter-ELM evolution of ion and electron temperature, electron and impurity density, or transport analysis of those channels. KBM can be ruled out as the dominant agent for heat transport. We find the Weakly Coherent Mode on C-Mod I-mode may be an electrostatic heavy particle/ITG mode. Analysis is ongoing for the C-Mod ELMy H-mode QCF. Pedestal density profiles in JET-ILW are consistent with ITG induced particle pinch. Work supported by US DOE under DE-FC02-04ER54698, DE-FG02-04ER54742 and DE-FC02-99ER54512 and by Eurofusion under Grant No. 633053.

A comparison of three organ dysfunction scores: MODS, SOFA and LOD for predicting ICU mortality in critically ill patients.

PubMed

Khwannimit, Bodin

2007-06-01

To compare the validity of the Multiple Organ Dysfunction Score (MODS), Sequential Organ Failure Assessment (SOFA), and Logistic Organ Dysfunction Score (LOD) for predicting ICU mortality of Thai critically ill patients. A retrospective study was made of prospective data collected between the 1st July 2004 and 31st March 2006 at Songklanagarind Hospital. One thousand seven hundred and eighty two patients were enrolled in the present study. Two hundred and ninety three (16.4%) deaths were recorded in the ICU. The areas under the Receiver Operating Curves (A UC) for the prediction of ICU mortality the results were 0.861 for MODS, 0.879 for SOFA and 0.880 for LOD. The AUC of SOFA and LOD showed a statistical significance higher than the MODS score (p = 0.014 and p = 0.042, respectively). Of all the models, the neurological failure score showed the best correlation with ICU mortality. All three organ dysfunction scores satisfactorily predicted ICU mortality. The LOD and neurological failure had the best correlation with ICU outcome.

Distribution and magnitude of type I error of model-based multipoint lod scores: implications for multipoint mod scores.

PubMed

Xing, Chao; Elston, Robert C

2006-07-01

The multipoint lod score and mod score methods have been advocated for their superior power in detecting linkage. However, little has been done to determine the distribution of multipoint lod scores or to examine the properties of mod scores. In this paper we study the distribution of multipoint lod scores both analytically and by simulation. We also study by simulation the distribution of maximum multipoint lod scores when maximized over different penetrance models. The multipoint lod score is approximately normally distributed with mean and variance that depend on marker informativity, marker density, specified genetic model, number of pedigrees, pedigree structure, and pattern of affection status. When the multipoint lod scores are maximized over a set of assumed penetrances models, an excess of false positive indications of linkage appear under dominant analysis models with low penetrances and under recessive analysis models with high penetrances. Therefore, caution should be taken in interpreting results when employing multipoint lod score and mod score approaches, in particular when inferring the level of linkage significance and the mode of inheritance of a trait.

Prise en compte des ``courants de London'' dans la modélisation des supraconducteurs

NASA Astrophysics Data System (ADS)

Bossavit, Alain

1997-10-01

A model is given, in variational form, in which volumic “Bean currents”, ruled by Bean's law, and surface “London currents” coexist. This macroscopic model generalizes Bean's one, by appending to the critical density j_c a second parameter, with the dimension of a length, similar to London's depth λ. The one-dimensional version of the model is investigated, in order to link this parameter with the standard observable H-M characteristics On propose un modèle, sous forme variationnelle, associant des “courants de Bean” volumiques, décrits par la loi de Bean, et des “courants de London”, surfaciques. Ce modèle macroscopique généralise celui de Bean, caractérisé par le courant critique j_c, et fait intervenir un second paramètre, homogène à une longueur, analogue au λ de London. La version unidimensionnelle du modèle est étudiée en détail de manière à relier ce paramètre à l'observation des caractéristiques H-M usuelles.

The Role of Plasma Rotation in C-Mod Internal Transport Barriers

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Ernst, D. R.; Rice, J. E.; Podpaly, Y.; Reinke, M. L.; Greenwald, M. J.; Hughes, J. W.; Ma, Y.; Bespamyatnov, I. O.; Rowan, W. L.

2010-11-01

ITBs in Alcator C-Mod featuring highly peaked density and pressure profiles are induced by injecting ICRF power with the second harmonic of the resonant frequency for minority hydrogen off-axis at the plasma half radius. These ITBs are formed in the absence of particle or momentum injection, and with monotonic q profiles with qmin < 1. In C-Mod a strong co-current toroidal rotation, peaked on axis, develops after the transition to H-mode. If an ITB forms, this rotation decreases in the center of the plasma and forms a well, and often reverses direction in the core. This indicates that there is a strong EXB shearing rate in the region where the foot in the ITB density profile is observed. Preliminary gyrokinetic analyses indicate that this shearing rate is comparable to the ion temperature gradient mode (ITG) growth rate at this location and may be responsible for stabilizing the turbulence. Gyrokinetic analyses of recent experimental data obtained from a complete scan of the ICRF resonance position across the entire C-Mod plasma will be presented.

Epitaxial strain effect in perovskite RENiO3 films (RE = La-Eu) prepared by metal organic decomposition

NASA Astrophysics Data System (ADS)

Ikeda, Ai; Manabe, Takaaki; Naito, Michio

2014-10-01

We report the synthesis of perovskite RENiO3 films (RE = La, Pr, Nd, Sm, and Eu) by metal organic decomposition (MOD). The RENiO3 family is an ideal system for studying the metal-insulator transition due to the simplicity of the materials. One of the drawbacks is that the bulk synthesis of the RENiO3 requires processing at high oxygen pressures to stabilize Ni3+. Fundamentally, MOD is similar to solid-state reaction, but it turned out that the MOD synthesis tends to stabilize RENiO3 without the need for high oxygen pressure. The films prepared by MOD show high crystallinity and low resistivity. Furthermore, we have investigated the epitaxial strain effect and observed a dramatic effect in PrNiO3 and NdNiO3 films on LaAlO3 substrates. The metal-insulator transition in the PrNiO3 films on LaAlO3 is fully suppressed, whereas the metal-insulator transition temperature is considerably lowered in the NdNiO3 films on LaAlO3.

Bench-to-bedside review: Angiopoietin signalling in critical illness – a future target?

PubMed Central

van Meurs, Matijs; Kümpers, Philipp; Ligtenberg, Jack JM; Meertens, John HJM; Molema, Grietje; Zijlstra, Jan G

2009-01-01

Multiple organ dysfunction syndrome (MODS) occurs in response to major insults such as sepsis, severe haemorrhage, trauma, major surgery and pancreatitis. The mortality rate is high despite intensive supportive care. The pathophysiological mechanism underlying MODS are not entirely clear, although several have been proposed. Overwhelming inflammation, immunoparesis, occult oxygen debt and other mechanisms have been investigated, and – despite many unanswered questions – therapies targeting these mechanisms have been developed. Unfortunately, only a few interventions, usually those targeting multiple mechanisms at the same time, have appeared to be beneficial. We clearly need to understand better the mechanisms that underlie MODS. The endothelium certainly plays an active role in MODS. It functions at the intersection of several systems, including inflammation, coagulation, haemodynamics, fluid and electrolyte balance, and cell migration. An important regulator of these systems is the angiopoietin/Tie2 signalling system. In this review we describe this signalling system, giving special attention to what is known about it in critically ill patients and its potential as a target for therapy. PMID:19435476

Effect of universal MODS access on pulmonary tuberculosis treatment outcomes in new patients in Peru

PubMed Central

Alarcón, E.; Alarcón, V.; Bissell, K.; Castillo, E.; Sabogal, I.; Mora, J.; Moore, D.; Harries, A. D.

2012-01-01

Setting: Primary health care centres in Callao, Peru. Objectives: To evaluate the effect of universal access to the microscopic-observation drug susceptibility (MODS) assay on treatment outcomes in new and primary multidrug-resistant tuberculosis (MDR-TB) patients and on the process of drug susceptibility testing (DST). Design: Retrospective review of tuberculosis (TB) registers and clinical records before (2007) and after (2009) the introduction of MODS in 2008. Results: There were 281 patients in each cohort. Favourable treatment outcomes for 2007 (81%) and 2009 (77%) cohorts were similar. There was an increase in loss to follow-up (from 6% to 10%, P = 0.04) and a reduction in failure rates (from 4% to 0.4%, P = 0.01) in the 2009 compared with the 2007 cohort. In new MDR-TB cases (n = 22), a favourable treatment outcome was improved (from 46% to 82%, P = 0.183) in the 2009 cohort. DST coverage improved (from 24% to 74%, P < 0.001), and a significant reduction in time to diagnosis of drug-susceptible (from 118 to 33 days, P < 0.001) and MDR-TB (from 158 to 52 days, P = 0.003) was observed in the 2009 cohort. Conclusion: Universal access to MODS increased DST coverage, reduced the time required to obtain DST results and was associated with reduced failure rates. MODS can make an important contribution to TB management and control in Peru. PMID:24579063

Comparison of RESP and IPolQ-Mod Partial Charges for Solvation Free Energy Calculations of Various Solute/Solvent Pairs.

PubMed

Mecklenfeld, Andreas; Raabe, Gabriele

2017-12-12

The calculation of solvation free energies ΔG solv by molecular simulations is of great interest as they are linked to other physical properties such as relative solubility, partition coefficient, and activity coefficient. However, shortcomings in molecular models can lead to ΔG solv deviations from experimental data. Various studies have demonstrated the impact of partial charges on free energy results. Consequently, calculation methods for partial charges aimed at more accurate ΔG solv predictions are the subject of various studies in the literature. Here we compare two methods to derive partial charges for the general AMBER force field (GAFF), i.e. the default RESP as well as the physically motivated IPolQ-Mod method that implicitly accounts for polarization costs. We study 29 solutes which include characteristic functional groups of drug-like molecules, and 12 diverse solvents were examined. In total, we consider 107 solute/solvent pairs including two water models TIP3P and TIP4P/2005. Comparison with experimental results yields better agreement for TIP3P, regardless of the partial charge scheme. The overall performance of GAFF/RESP and GAFF/IPolQ-Mod is similar, though specific shortcomings in the description of ΔG solv for both RESP and IPolQ-Mod can be identified. However, the high correlation between free energies obtained with GAFF/RESP and GAFF/IPolQ-Mod demonstrates the compatibility between the modified charges and remaining GAFF parameters.

Calculation of design load for the MOD-5A 7.3 mW wind turbine system

NASA Technical Reports Server (NTRS)

Mirandy, L.; Strain, J. C.

1995-01-01

Design loads are presented for the General Electric MOD-SA wind turbine. The MOD-SA system consists of a 400 ft. diameter, upwind, two-bladed, teetered rotor connected to a 7.3 mW variable-speed generator. Fatigue loads are specified in the form of histograms for the 30 year life of the machine, while limit (or maximum) loads have been derived from transient dynamic analysis at critical operating conditions. Loads prediction was accomplished using state of the art aeroelastic analyses developed at General Electric. Features of the primary predictive tool - the Transient Rotor Analysis Code (TRAC) are described in the paper. Key to the load predictions are the following wind models: (1) yearly mean wind distribution; (2) mean wind variations during operation; (3) number of start/shutdown cycles; (4) spatially large gusts; and (5) spatially small gusts (local turbulence). The methods used to develop statistical distributions from load calculations represent an extension of procedures used in past wind programs and are believed to be a significant contribution to Wind Turbine Generator analysis. Test/theory correlations are presented to demonstrate code load predictive capability and to support the wind models used in the analysis. In addition MOD-5A loads are compared with those of existing machines. The MOD-5A design was performed by the General Electric Company, Advanced Energy Program Department, under Contract DEN3-153 with NASA Lewis Research Center and sponsored by the Department of Energy.

MODIS-derived EVI, NDVI and WDRVI time series to estimate phenological metrics in French deciduous forests

NASA Astrophysics Data System (ADS)

Testa, S.; Soudani, K.; Boschetti, L.; Borgogno Mondino, E.

2018-02-01

Monitoring forest phenology allows us to study the effects of climate change on vegetated land surfaces. Daily and composite time series (TS) of several vegetation indices (VIs) from MODerate resolution Imaging Spectroradiometer (MODIS) data have been widely used in scientific works for phenological studies since the beginning of the MODIS mission. The objective of this work was to use MODIS data to find the best VI/TS combination to estimate start-of-season (SOS) and end-of-season (EOS) dates across 50 temperate deciduous forests. Our research used as inputs 2001-2012 daily reflectance from MOD09GQ/MOD09GA products and 16-day composite VIs from the MOD13Q1 dataset. The 50 pixels centered on the 50 forest plots were extracted from the above-mentioned MODIS imagery; we then generated 5 different types of TS (1 daily from MOD09 and 4 composite from MOD13Q1) and used all of them to implement 6 VIs, obtaining 30 VI/TS combinations. SOS and EOS estimates were determined for each pixel/year and each VI/TS combination. SOS/EOS estimations were then validated against ground phenological observations. Results showed that, in our test areas, composite TS, if actual acquisition date is considered, performed mostly better than daily TS. EVI, WDRVI0.20 and NDVI were more suitable to SOS estimation, while WDRVI0.05 and EVI were more convenient in estimating early and advanced EOS, respectively.

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis and computer science

NASA Technical Reports Server (NTRS)

1987-01-01

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis, and computer science during the period April, 1986 through September 30, 1986 is summarized.

78 FR 10180 - Annual Computational Science Symposium; Conference

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-13

...] Annual Computational Science Symposium; Conference AGENCY: Food and Drug Administration, HHS. ACTION... Computational Science Symposium.'' The purpose of the conference is to help the broader community align and share experiences to advance computational science. At the conference, which will bring together FDA...

Heart rate as an independent risk factor in patients with multiple organ dysfunction: a prospective, observational study.

PubMed

Hoke, Robert S; Müller-Werdan, Ursula; Lautenschläger, Christine; Werdan, Karl; Ebelt, Henning

2012-02-01

To study the association between baseline heart rate and outcome in patients with multiple organ dysfunction (MODS) as well as the course of heart rate over the first 4 days during MODS. Prospective observational study in 89 patients with MODS, defined as an APACHE-II score ≥20. Baseline heart rate (HR(0)) was determined over a 60-minute period at the time of MODS diagnosis. 28-day all-cause mortality was the primary endpoint of the study, a fall of the APACHE-II score by 4 points or more from day 0 to day 4 constituted the secondary endpoint. Hazard ratios for heart rate of 90 beats per minute (bpm) or greater relative to less than 90 bpm were calculated using Cox proportional hazards model and adjusted for confounding variables. Median baseline heart rate was 83 bpm in survivors and 92 bpm in non-survivors (p = 0.048). 28-day mortality was 32 and 61% in patients with HR(0) < 90 bpm and HR(0) ≥ 90 bpm, respectively. The adjusted hazard ratio for 28-day mortality was 2.30 (95% confidence interval 1.21-4.36, p = 0.001) for HR(0) ≥ 90 bpm relative to HR(0) < 90 bpm. No correlation was found between baseline heart rate and the secondary endpoint. From day 0 to day 4, heart rate remained elevated in all patients, as well as in survivors and non-survivors. A heart rate ≥90 bpm at the time of MODS diagnosis is an independent risk factor for increased 28-day mortality. As in patients with cardiovascular conditions such as coronary heart disease or chronic heart failure, heart rate might constitute a target for heart rate-lowering therapy in the narrow initial treatment window of MODS.

Basic principles and recent observations of rotationally sampled wind

NASA Technical Reports Server (NTRS)

Connell, James R.

1995-01-01

The concept of rotationally sampled wind speed is described. The unusual wind characteristics that result from rotationally sampling the wind are shown first for early measurements made using an 8-point ring of anemometers on a vertical plane array of meteorological towers. Quantitative characterization of the rotationally sampled wind is made in terms of the power spectral density function of the wind speed. Verification of the importance of the new concept is demonstrated with spectral analyses of the response of the MOD-OA blade flapwise root bending moment and the corresponding rotational analysis of the wind measured immediately upwind of the MOD-OA using a 12-point ring of anemometers on a 7-tower vertical plane array. The Pacific Northwest Laboratory (PNL) theory of the rotationally sampled wind speed power spectral density function is tested successfully against the wind spectrum measured at the MOD-OA vertical plane array. A single-tower empirical model of the rotationally sampled wind speed is also successfully tested against the measurements from the full vertical plane array. Rotational measurements of the wind velocity with hotfilm anemometers attached to rotating blades are shown to be accurate and practical for research on winds at the blades of wind turbines. Some measurements at the rotor blade of a MOD-2 turbine using the hotfilm technique in a pilot research program are shown. They are compared and contrasted to the expectations based upon application of the PNL theory of rotationally sampled wind to the MOD-2 size and rotation rate but without teeter, blade bending, or rotor induction accounted for. Finally, the importance of temperature layering and of wind modifications due to flow over complex terrain is demonstrated by the use of hotfilm anemometer data, and meteorological tower and acoustic doppler sounder data from the MOD-2 site at Goodnoe Hills, Washington.

Le rôle du soutien parental dans la relation entre la victimisation homophobe, l’homophobie intériorisée et la détresse psychologique chez les jeunes de minorités sexuelles (JMS) : une approche de médiation modérée

PubMed Central

Bergeron, Félix-Antoine; Blais, Martin; Hébert, Martine

2016-01-01

Résumé Cet article explore le rôle modérateur du soutien parental dans les relations entre la victimisation homophobe, l’homophobie intériorisée et la détresse psychologique chez des jeunes de minorités sexuelles (JMS), que l’on dit aussi lesbiennes, gais, bisexuels ou en questionnement. Il vise à 1) documenter la prévalence des différentes formes de victimisation homophobe vécue par les JMS, et ce, selon le genre et l’âge et 2) à explorer l’effet modérateur du soutien parental dans la relation entre la victimisation homophobe, l’homophobie intériorisée et la détresse psychologique. Un échantillon de 228 JMS âgés de 14 à 22 ans, non exclusivement hétérosexuels, recrutés en milieu communautaire dans le cadre de l’enquête sur le Parcours Amoureux des Jeunes (PAJ) du Québec a été analysé. L’impact de la victimisation homophobe, du soutien parental, de l’homophobie intériorisée sur la détresse psychologique est exploré par un modèle de régression linéaire avec effets de médiation modérée. Le rôle modérateur du soutien parental est confirmé dans la relation entre la victimisation homophobe et la détresse psychologique. Ces variables peuvent constituer des leviers pour prévenir les effets négatifs des préjudices homophobes sur la santé mentale des JMS. PMID:26966851

Predictive comparisons of procalcitonin (PCT) level, arterial ketone body ratio (AKBR), APACHE III score and multiple organ dysfunction score (MODS) in systemic inflammatory response syndrome (SIRS).

PubMed

Lee, Young-Joo; Park, Chan-Hee; Yun, Jang-Woon; Lee, Young-Suk

2004-02-29

Procalcitonin (PCT) is a newly introduced marker of systemic inflammation and bacterial infection. A marked increase in circulating PCT level in critically ill patients has been related with the severity of illness and poor survival. The goal of this study was to compare the prognostic power of PCT and three other parameters, the arterial ketone body ratio (AKBR), the acute physiology, age, chronic health evaluation (APACHE) III score and the multiple organ dysfunction score (MODS), in the differentiation between survivors and nonsurvivors of systemic inflammatory response syndrome (SIRS). The study was performed in 95 patients over 16 years of age who met the criteria of SIRS. PCT and AKBR were assayed in arterial blood samples. The APACHE III score and MODS were recorded after the first 24 hours of surgical ICU (SICU) admission and then daily for two weeks or until either discharge or death. The patients were divided into two groups, survivors (n=71) and nonsurvivors (n=24), in accordance with the ICU outcome. They were also divided into three groups according to the trend of PCT level: declining, increasing or no change. Significant differences between survivors and nonsurvivors were found in APACHE III score and MODS throughout the study period, but in PCT value only up to the 7th day and in AKBR only up to the 3rd day. PCT values of the three groups were not significantly different on the first day between survivors and nonsurvivors. Receiver operating characteristic (ROC) curves for prediction of mortality by PCT, AKBR, APACHE III score and MODS were 0.690, 0.320, 0.915 and 0.913, respectively, on the admission day. In conclusion, PCT could have some use as a mortality predictor in SIRS patients but was less reliable than APACHE III score or MODS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hules, John

This 1998 annual report from the National Scientific Energy Research Computing Center (NERSC) presents the year in review of the following categories: Computational Science; Computer Science and Applied Mathematics; and Systems and Services. Also presented are science highlights in the following categories: Basic Energy Sciences; Biological and Environmental Research; Fusion Energy Sciences; High Energy and Nuclear Physics; and Advanced Scientific Computing Research and Other Projects.

Risk stratification and prognostic performance of the predisposition, infection, response, and organ dysfunction (PIRO) scoring system in septic patients in the emergency department: a cohort study.

PubMed

Chen, Yun-Xia; Li, Chun-Sheng

2014-04-16

The predisposition, infection, response and organ dysfunction (PIRO) staging system was designed as a stratification tool to deal with the inherent heterogeneity of septic patients. The present study was conducted to assess the performance of PIRO in predicting multiple organ dysfunction (MOD), intensive care unit (ICU) admission, and 28-day mortality in septic patients in the emergency department (ED), and to compare this scoring system with the Mortality in Emergency Department Sepsis (MEDS) and Acute Physiology and Chronic Health Evaluation (APACHE II) scores. Consecutive septic patients (n = 680) admitted to the ED of Beijing Chao-Yang Hospital were enrolled. PIRO, MEDS, and APACHE II scores were calculated for each patient on ED arrival. Organ function was reassessed within 3 days of enrollment. All patients were followed up for 28 days. Outcome criteria were the development of MOD within 3 days, ICU admission or death within 28 days after enrollment. The predictive ability of the four components of PIRO was analyzed separately. Receiver operating characteristic (ROC) curve and logistic regression analysis were used to assess the prognostic and risk stratification value of the scoring systems. Organ dysfunction independently predicted ICU admission, MOD, and 28-day mortality, with areas under the ROC curve (AUC) of 0.888, 0.851, and 0.816, respectively. The predictive value of predisposition, infection, and response was weaker than that of organ dysfunction. A negative correlation was found between the response component and MOD, as well as mortality. PIRO, MEDS, and APACHE II scores significantly differed between patients who did and did not meet the outcome criteria (P < 0.001). PIRO and APACHE II independently predicted ICU admission and MOD, but MEDS did not. All three systems were independent predictors of 28-day mortality with similar AUC values. The AUC of PIRO was 0.889 for ICU admission, 0.817 for MOD, and 0.744 for 28-day mortality. The AUCs of PIRO were significantly greater than those of APACHE II and MEDS (P < 0.05) in predicting ICU admission and MOD. The study indicates that PIRO is helpful for risk stratification and prognostic determinations in septic patients in the ED.

Enhancement of the MODIS Daily Snow Albedo Product

NASA Technical Reports Server (NTRS)

Hall, Dorothy K.; Schaaf, Crystal B.; Wang, Zhuosen; Riggs, George A.

2009-01-01

The MODIS daily snow albedo product is a data layer in the MOD10A1 snow-cover product that includes snow-covered area and fractional snow cover as well as quality information and other metadata. It was developed to augment the MODIS BRDF/Albedo algorithm (MCD43) that provides 16-day maps of albedo globally at 500-m resolution. But many modelers require daily snow albedo, especially during the snowmelt season when the snow albedo is changing rapidly. Many models have an unrealistic snow albedo feedback in both estimated albedo and change in albedo over the seasonal cycle context, Rapid changes in snow cover extent or brightness challenge the MCD43 algorithm; over a 16-day period, MCD43 determines whether the majority of clear observations was snow-covered or snow-free then only calculates albedo for the majority condition. Thus changes in snow albedo and snow cover are not portrayed accurately during times of rapid change, therefore the current MCD43 product is not ideal for snow work. The MODIS daily snow albedo from the MOD10 product provides more frequent, though less robust maps for pixels defined as "snow" by the MODIS snow-cover algorithm. Though useful, the daily snow albedo product can be improved using a daily version of the MCD43 product as described in this paper. There are important limitations to the MOD10A1 daily snow albedo product, some of which can be mitigated. Utilizing the appropriate per-pixel Bidirectional Reflectance Distribution Functions (BRDFs) can be problematic, and correction for anisotropic scattering must be included. The BRDF describes how the reflectance varies with view and illumination geometry. Also, narrow-to-broadband conversion specific for snow on different surfaces must be calculated and this can be difficult. In consideration of these limitations of MOD10A1, we are planning to improve the daily snow albedo algorithm by coupling the periodic per-pixel snow albedo from MCD43, with daily surface ref|outanoom, In this paper, we compare a daily version of MCD43B3 with the daily albedo from MOD10A1. and MCD43B3 with a 16-day average of MOD10A1, over Greenland. We also discuss some near-future planned enhancements to MOD10A1.

How much do different global GPP products agree in distribution and magnitude of GPP extremes?

NASA Astrophysics Data System (ADS)

Kim, S.; Ryu, Y.; Jiang, C.

2016-12-01

To evaluate uncertainty of global Gross Primary Productivity (GPP) extremes, we compare three global GPP datasets derived from different data processing methods (e.g. MPI-BGC: machine-learning, MODIS GPP (MOD17): semi-empirical, Breathing Earth System Simulator (BESS): process based). We preprocess the datasets following the method from Zscheischler et al., (2012) to detect GPP extremes which occur in less than 1% of the number of whole pixels, and to identify 3D-connected spatiotemporal GPP extremes. We firstly analyze global patterns and the magnitude of GPP extremes with MPI-BGC, MOD17, and BESS over 2001-2011. For consistent analysis in the three products, spatial and temporal resolution were set at 50 km and a monthly scale, respectively. Our results indicated that the global patterns of GPP extremes derived from MPI-BGC and BESS agreed with each other by showing hotspots in Northeastern Brazil and Eastern Texas. However, the extreme events detected from MOD17 were concentrated in tropical forests (e.g. Southeast Asia and South America). The amount of GPP reduction caused by climate extremes considerably differed across the products. For example, Russian heatwave in 2010 led to 100 Tg C uncertainty (198.7 Tg C in MPI-BGC, 305.6 Tg C in MOD17, and 237.8 Tg C in BESS). Moreover, the duration of extreme events differ among the three GPP datasets for the Russian heatwave (MPI-BGC: May-Sep, MOD17: Jun-Aug, and BESS: May-Aug). To test whether Sun induced Fluorescence (SiF), a proxy of GPP, can capture GPP extremes, we investigate global distribution of GPP extreme events in BESS, MOD17 and GOME-2 SiF between 2008 and 2014 when SiF data is available. We found that extreme GPP events in GOME-2 SiF and MOD17 appear in tropical forests whereas those in BESS emerged in Northeastern Brazil and Eastern Texas. The GPP extremes by severe 2011 US drought were detected by BESS and MODIS, but not by SiF. Our findings highlight that different GPP datasets could result in varying duration and intensity of GPP extremes and distribution of hotspots, and this study could contribute to quantifying uncertainties in GPP extremes.

Enduring Influence of Stereotypical Computer Science Role Models on Women's Academic Aspirations

ERIC Educational Resources Information Center

Cheryan, Sapna; Drury, Benjamin J.; Vichayapai, Marissa

2013-01-01

The current work examines whether a brief exposure to a computer science role model who fits stereotypes of computer scientists has a lasting influence on women's interest in the field. One-hundred undergraduate women who were not computer science majors met a female or male peer role model who embodied computer science stereotypes in appearance…

A Web of Resources for Introductory Computer Science.

ERIC Educational Resources Information Center

Rebelsky, Samuel A.

As the field of Computer Science has grown, the syllabus of the introductory Computer Science course has changed significantly. No longer is it a simple introduction to programming or a tutorial on computer concepts and applications. Rather, it has become a survey of the field of Computer Science, touching on a wide variety of topics from digital…

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis and computer science

NASA Technical Reports Server (NTRS)

1988-01-01

This report summarizes research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis, and computer science during the period April l, 1988 through September 30, 1988.

Summary of research in applied mathematics, numerical analysis and computer science at the Institute for Computer Applications in Science and Engineering

NASA Technical Reports Server (NTRS)

1984-01-01

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis and computer science during the period October 1, 1983 through March 31, 1984 is summarized.

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis and computer science

NASA Technical Reports Server (NTRS)

1987-01-01

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis, and computer science during the period October 1, 1986 through March 31, 1987 is summarized.

High school computer science education paves the way for higher education: the Israeli case

NASA Astrophysics Data System (ADS)

Armoni, Michal; Gal-Ezer, Judith

2014-07-01

The gap between enrollments in higher education computing programs and the high-tech industry's demands is widely reported, and is especially prominent for women. Increasing the availability of computer science education in high school is one of the strategies suggested in order to address this gap. We look at the connection between exposure to computer science in high school and pursuing computing in higher education. We also examine the gender gap, in the context of high school computer science education. We show that in Israel, students who took the high-level computer science matriculation exam were more likely to pursue computing in higher education. Regarding the issue of gender, we will show that, in general, in Israel the difference between males and females who take computer science in high school is relatively small, and a larger, though still not very large difference exists only for the highest exam level. In addition, exposing females to high-level computer science in high school has more relative impact on pursuing higher education in computing.

Defining Computational Thinking for Mathematics and Science Classrooms

NASA Astrophysics Data System (ADS)

Weintrop, David; Beheshti, Elham; Horn, Michael; Orton, Kai; Jona, Kemi; Trouille, Laura; Wilensky, Uri

2016-02-01

Science and mathematics are becoming computational endeavors. This fact is reflected in the recently released Next Generation Science Standards and the decision to include "computational thinking" as a core scientific practice. With this addition, and the increased presence of computation in mathematics and scientific contexts, a new urgency has come to the challenge of defining computational thinking and providing a theoretical grounding for what form it should take in school science and mathematics classrooms. This paper presents a response to this challenge by proposing a definition of computational thinking for mathematics and science in the form of a taxonomy consisting of four main categories: data practices, modeling and simulation practices, computational problem solving practices, and systems thinking practices. In formulating this taxonomy, we draw on the existing computational thinking literature, interviews with mathematicians and scientists, and exemplary computational thinking instructional materials. This work was undertaken as part of a larger effort to infuse computational thinking into high school science and mathematics curricular materials. In this paper, we argue for the approach of embedding computational thinking in mathematics and science contexts, present the taxonomy, and discuss how we envision the taxonomy being used to bring current educational efforts in line with the increasingly computational nature of modern science and mathematics.

Nicholas Brunhart-Lupo | NREL

Science.gov Websites

. Education Ph.D., Computer Science, Colorado School of Mines M.S., Computer Science, University of Queensland B.S., Computer Science, Colorado School of Mines Brunhart-Lupo Nicholas Brunhart-Lupo Computational Science Nicholas.Brunhart-Lupo@nrel.gov

The Need for Computer Science

ERIC Educational Resources Information Center

Margolis, Jane; Goode, Joanna; Bernier, David

2011-01-01

Broadening computer science learning to include more students is a crucial item on the United States' education agenda, these authors say. Although policymakers advocate more computer science expertise, computer science offerings in high schools are few--and actually shrinking. In addition, poorly resourced schools with a high percentage of…

Summary of research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis and computer science

NASA Technical Reports Server (NTRS)

1989-01-01

Research conducted at the Institute for Computer Applications in Science and Engineering in applied mathematics, numerical analysis, and computer science during the period October 1, 1988 through March 31, 1989 is summarized.

Alliance for Computational Science Collaboration HBCU Partnership at Fisk University. Final Report 2001

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, W. E.

2004-08-16

Computational Science plays a big role in research and development in mathematics, science, engineering and biomedical disciplines. The Alliance for Computational Science Collaboration (ACSC) has the goal of training African-American and other minority scientists in the computational science field for eventual employment with the Department of Energy (DOE). The involvements of Historically Black Colleges and Universities (HBCU) in the Alliance provide avenues for producing future DOE African-American scientists. Fisk University has been participating in this program through grants from the DOE. The DOE grant supported computational science activities at Fisk University. The research areas included energy related projects, distributed computing,more » visualization of scientific systems and biomedical computing. Students' involvement in computational science research included undergraduate summer research at Oak Ridge National Lab, on-campus research involving the participation of undergraduates, participation of undergraduate and faculty members in workshops, and mentoring of students. These activities enhanced research and education in computational science, thereby adding to Fisk University's spectrum of research and educational capabilities. Among the successes of the computational science activities are the acceptance of three undergraduate students to graduate schools with full scholarships beginning fall 2002 (one for master degree program and two for Doctoral degree program).« less

Mound powder loader, Mod 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gress, A.V. Jr.

1985-08-21

At the investigation of Sandia Albuquerque, a semiautomatic powder loader was designed and fabricated for pyrotechnics devices. The basic functions of the system were to load a precise, measured amount of powder into a charge holder and to compact the mixture to a specified density. This report documents the history, rationale, design, and performance of the Mod 1 loader.

Operational Range Assessment Program (ORAP) Phase II Overview for Active Installations

DTIC Science & Technology

2011-05-01

Dissolved Metals by EPA 1638M • Isotopic Uranium by EML A-01-R Mod  Sediment Analysis • None  Benthic Macroinvertebrates • Diversity Indices...Metals by EPA 200.8 • Dissolved Metals by EPA 200.8 (if turbid) • Isotopic Uranium by EML A-01- R Mod (if total U is > action limit) Groundwater

Advancement of a soil parameters geodatabase for the modeling assessment of conservation practice outcomes in the United States

USDA-ARS?s Scientific Manuscript database

US-ModSoilParms-TEMPLE is a database composed of a set of geographic databases functionally storing soil-spatial units and soil hydraulic, physical, and chemical parameters for three agriculture management simulation models, SWAT, APEX, and ALMANAC. This paper introduces the updated US-ModSoilParms-...

Blade design and operating experience on the MOD-OA 200 kW wind turbine at Clayton, New Mexico

NASA Technical Reports Server (NTRS)

Linscott, B. S.; Shaltens, R. K.

1979-01-01

Two 60 foot long aluminum wind turbine blades were operated for over 3000 hours on the MOD-OA wind turbine. The first signs of blade structural damage were observed after 400 hours of operation. Details of the blade design, loads, cost, structural damage, and repair are discussed.

Assessment of PWR Steam Generator modelling in RELAP5/MOD2. International Agreement Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Putney, J.M.; Preece, R.J.

1993-06-01

An assessment of Steam Generator (SG) modelling in the PWR thermal-hydraulic code RELAP5/MOD2 is presented. The assessment is based on a review of code assessment calculations performed in the UK and elsewhere, detailed calculations against a series of commissioning tests carried out on the Wolf Creek PWR and analytical investigations of the phenomena involved in normal and abnormal SG operation. A number of modelling deficiencies are identified and their implications for PWR safety analysis are discussed -- including methods for compensating for the deficiencies through changes to the input deck. Consideration is also given as to whether the deficiencies willmore » still be present in the successor code RELAP5/MOD3.« less

TRAC-PF1/MOD1 support calculations for the MIST/OTIS program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fujita, R.K.; Knight, T.D.

1984-01-01

We are using the Transient Reactor Analysis Code (TRAC), specifically version TRAC-PF1/MOD1, to perform analyses in support of the MultiLoop Integral-System Test (MIST) and the Once-Through Integral-System (OTIS) experiment program. We have analyzed Geradrohr Dampferzeuger Anlage (GERDA) Test 1605AA to benchmark the TRAC-PF1/MOD1 code against phenomena expected to occur in a raised-loop B and W plant during a small-break loss-of-coolant accident (SBLOCA). These results show that the code can calculate both single- and two-phase natural circulation, flow interruption, boiler-condenser-mode (BCM) heat transfer, and primary-system refill in a B and W-type geometry with low-elevation auxiliary feedwater. 19 figures, 7 tables.

Transportable Payload Operations Control Center reusable software: Building blocks for quality ground data systems

NASA Technical Reports Server (NTRS)

Mahmot, Ron; Koslosky, John T.; Beach, Edward; Schwarz, Barbara

1994-01-01

The Mission Operations Division (MOD) at Goddard Space Flight Center builds Mission Operations Centers which are used by Flight Operations Teams to monitor and control satellites. Reducing system life cycle costs through software reuse has always been a priority of the MOD. The MOD's Transportable Payload Operations Control Center development team established an extensive library of 14 subsystems with over 100,000 delivered source instructions of reusable, generic software components. Nine TPOCC-based control centers to date support 11 satellites and achieved an average software reuse level of more than 75 percent. This paper shares experiences of how the TPOCC building blocks were developed and how building block developer's, mission development teams, and users are all part of the process.

Measurement and prediction of broadband noise from large horizontal axis wind turbine generators

NASA Technical Reports Server (NTRS)

Grosveld, F. W.; Shepherd, K. P.; Hubbard, H. H.

1995-01-01

A method is presented for predicting the broadband noise spectra of large wind turbine generators. It includes contributions from such noise sources as the inflow turbulence to the rotor, the interactions between the turbulent boundary layers on the blade surfaces with their trailing edges and the wake due to a blunt trailing edge. The method is partly empirical and is based on acoustic measurements of large wind turbines and airfoil models. Spectra are predicted for several large machines including the proposed MOD-5B. Measured data are presented for the MOD-2, the WTS-4, the MOD-OA, and the U.S. Windpower Inc. machines. Good agreement is shown between the predicted and measured far field noise spectra.

Effect of vortex generators on the power conversion performance and structural dynamic loads of the Mod-2 wind turbine

NASA Technical Reports Server (NTRS)

Sullivan, T. L.

1984-01-01

Applying vortex generators from 20 to 100 percent span of the Mod-2 rotor resulted in a projected increase in annual energy capture of 20 percent and reduced the wind speed at which rated power is reached by nearly 3 m/sec. Application of vortex generators from 20 to 70 percent span, the fixed portion of the Mod-2 rotor, resulted in a projected increase in annual energy capture of about half this. This improved performance came at the cost of a small increase in cyclic blade loads in below rated power conditions. Cyclic blade loads were found to correlate well with the change in wind speed during one rotor revolution.

airGR: a suite of lumped hydrological models in an R-package

NASA Astrophysics Data System (ADS)

Coron, Laurent; Perrin, Charles; Delaigue, Olivier; Andréassian, Vazken; Thirel, Guillaume

2016-04-01

Lumped hydrological models are useful and convenient tools for research, engineering and educational purposes. They propose catchment-scale representations of the precipitation-discharge relationship. Thanks to their limited data requirements, they can be easily implemented and run. With such models, it is possible to simulate a number of hydrological key processes over the catchment with limited structural and parametric complexity, typically evapotranspiration, runoff, underground losses, etc. The Hydrology Group at Irstea (Antony) has been developing a suite of rainfall-runoff models over the past 30 years with the main objectives of designing models as efficient as possible in terms of streamflow simulation, applicable to a wide range of catchments and having low data requirements. This resulted in a suite of models running at different time steps (from hourly to annual) applicable for various issues including water balance estimation, forecasting, simulation of impacts and scenario testing. Recently, Irstea has developed an easy-to-use R-package (R Core Team, 2015), called airGR, to make these models widely available. It includes: - the water balance annual GR1A (Mouehli et al., 2006), - the monthly GR2M (Mouehli, 2003) models, - three versions of the daily model, namely GR4J (Perrin et al., 2003), GR5J (Le Moine, 2008) and GR6J (Pushpalatha et al., 2011), - the hourly GR4H model (Mathevet, 2005), - a degree-day snow module CemaNeige (Valéry et al., 2014). The airGR package has been designed to facilitate the use by non-expert users and allow the addition of evaluation criteria, models or calibration algorithms selected by the end-user. Each model core is coded in FORTRAN to ensure low computational time. The other package functions (i.e. mainly the calibration algorithm and the efficiency criteria) are coded in R. The package is already used for educational purposes. The presentation will detail the main functionalities of the package and present a case study application. References: - Le Moine, N. (2008), Le bassin versant de surface vu par le souterrain : une voie d'amélioration des performances et du réalisme des modèles pluie-débit ?, PhD thesis (in French), UPMC, Paris, France. - Mathevet, T. (2005), Quels modèles pluie-débit globaux pour le pas de temps horaire ? Développement empirique et comparaison de modèles sur un large échantillon de bassins versants, PhD thesis (in French), ENGREF - Cemagref (Antony), Paris, France. - Mouelhi S. (2003), Vers une chaîne cohérente de modèles pluie-débit conceptuels globaux aux pas de temps pluriannuel, annuel, mensuel et journalier, PhD thesis (in French), ENGREF - Cemagref Antony, Paris, France. - Mouelhi, S., C. Michel, C. Perrin and V. Andréassian (2006), Stepwise development of a two-parameter monthly water balance model, Journal of Hydrology, 318(1-4), 200-214, doi:10.1016/j.jhydrol.2005.06.014. - Perrin, C., C. Michel and V. Andréassian (2003), Improvement of a parsimonious model for streamflow simulation, Journal of Hydrology, 279(1-4), 275-289, doi:10.1016/S0022-1694(03)00225-7. - Pushpalatha, R., C. Perrin, N. Le Moine, T. Mathevet and V. Andréassian (2011), A downward structural sensitivity analysis of hydrological models to improve low-flow simulation, Journal of Hydrology, 411(1-2), 66-76, doi:10.1016/j.jhydrol.2011.09.034. - R Core Team (2015). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. URL https://www.R-project.org/ - Valéry, A., V. Andréassian and C. Perrin (2014), "As simple as possible but not simpler": What is useful in a temperature-based snow-accounting routine? Part 2 - Sensitivity analysis of the Cemaneige snow accounting routine on 380 catchments, Journal of Hydrology, doi:10.1016/j.jhydrol.2014.04.058.

A NASTRAN-based computer program for structural dynamic analysis of Horizontal Axis Wind Turbines

NASA Technical Reports Server (NTRS)

Lobitz, Don W.

1995-01-01

This paper describes a computer program developed for structural dynamic analysis of horizontal axis wind turbines (HAWT's). It is based on the finite element method through its reliance on NASTRAN for the development of mass, stiffness, and damping matrices of the tower end rotor, which are treated in NASTRAN as separate structures. The tower is modeled in a stationary frame and the rotor in one rotating at a constant angular velocity. The two structures are subsequently joined together (external to NASTRAN) using a time-dependent transformation consistent with the hub configuration. Aerodynamic loads are computed with an established flow model based on strip theory. Aeroelastic effects are included by incorporating the local velocity and twisting deformation of the blade in the load computation. The turbulent nature of the wind, both in space and time, is modeled by adding in stochastic wind increments. The resulting equations of motion are solved in the time domain using the implicit Newmark-Beta integrator. Preliminary comparisons with data from the Boeing/NASA MOD2 HAWT indicate that the code is capable of accurately and efficiently predicting the response of HAWT's driven by turbulent winds.

Curricular Influences on Female Afterschool Facilitators' Computer Science Interests and Career Choices

NASA Astrophysics Data System (ADS)

Koch, Melissa; Gorges, Torie

2016-10-01

Underrepresented populations such as women, African-Americans, and Latinos/as often come to STEM (science, technology, engineering, and mathematics) careers by less traditional paths than White and Asian males. To better understand how and why women might shift toward STEM, particularly computer science, careers, we investigated the education and career direction of afterschool facilitators, primarily women of color in their twenties and thirties, who taught Build IT, an afterschool computer science curriculum for middle school girls. Many of these women indicated that implementing Build IT had influenced their own interest in technology and computer science and in some cases had resulted in their intent to pursue technology and computer science education. We wanted to explore the role that teaching Build IT may have played in activating or reactivating interest in careers in computer science and to see whether in the years following implementation of Build IT, these women pursued STEM education and/or careers. We reached nine facilitators who implemented the program in 2011-12 or shortly after. Many indicated that while facilitating Build IT, they learned along with the participants, increasing their interest in and confidence with technology and computer science. Seven of the nine participants pursued further STEM or computer science learning or modified their career paths to include more of a STEM or computer science focus. Through interviews, we explored what aspects of Build IT influenced these facilitators' interest and confidence in STEM and when relevant their pursuit of technology and computer science education and careers.