Investigation of thermal effects on FinFETs in the quasi-ballistic regime

NASA Astrophysics Data System (ADS)

Yin, Longxiang; Shen, Lei; Di, Shaoyan; Du, Gang; Liu, Xiaoyan

2018-04-01

In this work, the thermal effects of FinFETs in the quasi-ballistic regime are investigated using the Monte Carlo method. Bulk Si nFinFETs with the same fin structure and two different gate lengths L g = 20 and 80 nm are investigated and compared to evaluate the thermal effects on the performance of FinFETs in the quasi-ballistic regime. The on current of the 20 nm FinFET with V gs = 0.7 V does not decrease with increasing lattice temperature (T L) at a high V ds. The electrostatic properties in the 20 nm FinFET are more affected by T L than those in the 80 nm FinFET. However, the electron transport in the 20 nm FinFET is less affected by T L than that in the 80 nm FinFET. The electrostatic properties being more sensitive and the electron transport being less sensitive to thermal effects in the quasi-ballistic regime than in the diffusive regime should be considered for effective device modeling and design.

Effect of helmet liner systems and impact directions on severity of head injuries sustained in ballistic impacts: a finite element (FE) study.

PubMed

Tse, Kwong Ming; Tan, Long Bin; Yang, Bin; Tan, Vincent Beng Chye; Lee, Heow Pueh

2017-04-01

The current study aims to investigate the effectiveness of two different designs of helmet interior cushion, (Helmet 1: strap-netting; Helmet 2: Oregon Aero foam-padding), and the effect of the impact directions on the helmeted head during ballistic impact. Series of ballistic impact simulations (frontal, lateral, rear, and top) of a full-metal-jacketed bullet were performed on a validated finite element head model equipped with the two helmets, to assess the severity of head injuries sustained in ballistic impacts using both head kinematics and biomechanical metrics. Benchmarking with experimental ventricular and intracranial pressures showed that there is good agreement between the simulations and experiments. In terms of extracranial injuries, top impact had the highest skull stress, still without fracturing the skull. In regard to intracranial injuries, both the lateral and rear impacts generally gave the highest principal strains as well as highest shear strains, which exceed the injury thresholds. Off-cushion impacts were found to be at higher risk of intracranial injuries. The study also showed that the Oregon Aero foam pads helped to reduce impact forces. It also suggested that more padding inserts of smaller size may offer better protection. This provides some insights on future's helmet design against ballistic threats.

Integrated Projectile Systems Synthesis Model (IPSSM)

DTIC Science & Technology

1976-08-01

Lethal area effectiveness Batch mode I terior ballistics Trajectory calculations Weapon system modeling ""TRACT (Cenetsmae an revers elds It ecesuy and...Ballistics (AR) 29 E. Terminal Effectiveness Calculations (LA) 31 F. 6-D Trajectory (TR) 32 G. Recoil Mechanism Design (RM) 33 H. Sabot Design (SD) 33 I...Exterior Ballistics Program (AR) 79 Key Variable Input D2 Exterior Ballistics Program (AR) 89 List of Tables E Terminal Effectiveness Program (LA) 93

Ballistic Performance of Porous-Ceramic, Thermal-Protection-Systems

NASA Technical Reports Server (NTRS)

Christiansen, E. L.; Davis, B. A.; Miller, J. E.; Bohl, W. E.; Foreman, C. D.

2009-01-01

Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Space Shuttle and are currently being proposed for the next generation of manned spacecraft, Orion. These materials insulate the structural components of a spacecraft against the intense thermal environments of atmospheric reentry. Furthermore, these materials are also highly exposed to space environmental hazards like meteoroid and orbital debris impacts. This paper discusses recent impact testing up to 9 km/s, and the findings of the influence of material equation-of-state on the simulation of the impact event to characterize the ballistic performance of these materials. These results will be compared with heritage models1 for these materials developed from testing at lower velocities. Assessments of predicted spacecraft risk based upon these tests and simulations will also be discussed.

Hybrid composite laminates reinforced with Kevlar/carbon/glass woven fabrics for ballistic impact testing.

PubMed

Randjbaran, Elias; Zahari, Rizal; Jalil, Nawal Aswan Abdul; Majid, Dayang Laila Abang Abdul

2014-01-01

Current study reported a facile method to investigate the effects of stacking sequence layers of hybrid composite materials on ballistic energy absorption by running the ballistic test at the high velocity ballistic impact conditions. The velocity and absorbed energy were accordingly calculated as well. The specimens were fabricated from Kevlar, carbon, and glass woven fabrics and resin and were experimentally investigated under impact conditions. All the specimens possessed equal mass, shape, and density; nevertheless, the layers were ordered in different stacking sequence. After running the ballistic test at the same conditions, the final velocities of the cylindrical AISI 4340 Steel pellet showed how much energy was absorbed by the samples. The energy absorption of each sample through the ballistic impact was calculated; accordingly, the proper ballistic impact resistance materials could be found by conducting the test. This paper can be further studied in order to characterise the material properties for the different layers.

Supercurrent and multiple Andreev reflections in micrometer-long ballistic graphene Josephson junctions.

PubMed

Zhu, Mengjian; Ben Shalom, Moshe; Mishchsenko, Artem; Fal'ko, Vladimir; Novoselov, Kostya; Geim, Andre

2018-02-08

Ballistic Josephson junctions are predicted to support a number of exotic physics processess, providing an ideal system to inject the supercurrent in the quantum Hall regime. Herein, we demonstrate electrical transport measurements on ballistic superconductor-graphene-superconductor junctions by contacting graphene to niobium with a junction length up to 1.5 μm. Hexagonal boron nitride encapsulation and one-dimensional edge contacts guarantee high-quality graphene Josephson junctions with a mean free path of several micrometers and record-low contact resistance. Transports in normal states including the observation of Fabry-Pérot oscillations and Sharvin resistance conclusively witness the ballistic propagation in the junctions. The critical current density J C is over one order of magnitude larger than that of the previously reported junctions. Away from the charge neutrality point, the I C R N product (I C is the critical current and R N the normal state resistance of junction) is nearly a constant, independent of carrier density n, which agrees well with the theory for ballistic Josephson junctions. Multiple Andreev reflections up to the third order are observed for the first time by measuring the differential resistance in the micrometer-long ballistic graphene Josephson junctions.

Signature analysis of ballistic missile warhead with micro-nutation in terahertz band

NASA Astrophysics Data System (ADS)

Li, Ming; Jiang, Yue-song

2013-08-01

In recent years, the micro-Doppler effect has been proposed as a new technique for signature analysis and extraction of radar targets. The ballistic missile is known as a typical radar target and has been paid many attentions for the complexities of its motions in current researches. The trajectory of a ballistic missile can be generally divided into three stages: boost phase, midcourse phase and terminal phase. The midcourse phase is the most important phase for radar target recognition and interception. In this stage, the warhead forms a typical micro-motion called micro-nutation which consists of three basic micro-motions: spinning, coning and wiggle. This paper addresses the issue of signature analysis of ballistic missile warhead in terahertz band via discussing the micro-Doppler effect. We establish a simplified model (cone-shaped) for the missile warhead followed by the micro-motion models including of spinning, coning and wiggle. Based on the basic formulas of these typical micro-motions, we first derive the theoretical formula of micro-nutation which is the main micro-motion of the missile warhead. Then, we calculate the micro-Doppler frequency in both X band and terahertz band via these micro-Doppler formulas. The simulations are given to show the superiority of our proposed method for the recognition and detection of radar micro targets in terahertz band.

Going ballistic: Graphene hot electron transistors

NASA Astrophysics Data System (ADS)

Vaziri, S.; Smith, A. D.; Östling, M.; Lupina, G.; Dabrowski, J.; Lippert, G.; Mehr, W.; Driussi, F.; Venica, S.; Di Lecce, V.; Gnudi, A.; König, M.; Ruhl, G.; Belete, M.; Lemme, M. C.

2015-12-01

This paper reviews the experimental and theoretical state of the art in ballistic hot electron transistors that utilize two-dimensional base contacts made from graphene, i.e. graphene base transistors (GBTs). Early performance predictions that indicated potential for THz operation still hold true today, even with improved models that take non-idealities into account. Experimental results clearly demonstrate the basic functionality, with on/off current switching over several orders of magnitude, but further developments are required to exploit the full potential of the GBT device family. In particular, interfaces between graphene and semiconductors or dielectrics are far from perfect and thus limit experimental device integrity, reliability and performance.

Localization of small arms fire using acoustic measurements of muzzle blast and/or ballistic shock wave arrivals.

PubMed

Lo, Kam W; Ferguson, Brian G

2012-11-01

The accurate localization of small arms fire using fixed acoustic sensors is considered. First, the conventional wavefront-curvature passive ranging method, which requires only differential time-of-arrival (DTOA) measurements of the muzzle blast wave to estimate the source position, is modified to account for sensor positions that are not strictly collinear (bowed array). Second, an existing single-sensor-node ballistic model-based localization method, which requires both DTOA and differential angle-of-arrival (DAOA) measurements of the muzzle blast wave and ballistic shock wave, is improved by replacing the basic external ballistics model (which describes the bullet's deceleration along its trajectory) with a more rigorous model and replacing the look-up table ranging procedure with a nonlinear (or polynomial) equation-based ranging procedure. Third, a new multiple-sensor-node ballistic model-based localization method, which requires only DTOA measurements of the ballistic shock wave to localize the point of fire, is formulated. The first method is applicable to situations when only the muzzle blast wave is received, whereas the third method applies when only the ballistic shock wave is received. The effectiveness of each of these methods is verified using an extensive set of real data recorded during a 7 day field experiment.

Nanotubes in Nanoelectronics: Transport, Growth and Modeling

NASA Technical Reports Server (NTRS)

Anantram, M.; Delzeit, Lance; Cassell, Alan; Han, Jie; Meyyappan, M.; Arnold, Jim (Technical Monitor)

2001-01-01

Carbon nanotube (CNT) baud nanotechnology appears to be promising for future Theoretical analysis and results for the ballistic current carrying capacity of nanotube wires am presented. Aspects of metal-nanotube coupling are examined. Results am also presented for chemical vapor deposition of CNT from hydrocarbon feedstock.

3-D ballistic transport of ellipsoidal volcanic projectiles considering horizontal wind field and variable shape-dependent drag coefficients

NASA Astrophysics Data System (ADS)

Bertin, Daniel

2017-02-01

An innovative 3-D numerical model for the dynamics of volcanic ballistic projectiles is presented here. The model focuses on ellipsoidal particles and improves previous approaches by considering horizontal wind field, virtual mass forces, and drag forces subjected to variable shape-dependent drag coefficients. Modeling suggests that the projectile's launch velocity and ejection angle are first-order parameters influencing ballistic trajectories. The projectile's density and minor radius are second-order factors, whereas both intermediate and major radii of the projectile are of third order. Comparing output parameters, assuming different input data, highlights the importance of considering a horizontal wind field and variable shape-dependent drag coefficients in ballistic modeling, which suggests that they should be included in every ballistic model. On the other hand, virtual mass forces should be discarded since they almost do not contribute to ballistic trajectories. Simulation results were used to constrain some crucial input parameters (launch velocity, ejection angle, wind speed, and wind azimuth) of the block that formed the biggest and most distal ballistic impact crater during the 1984-1993 eruptive cycle of Lascar volcano, Northern Chile. Subsequently, up to 106 simulations were performed, whereas nine ejection parameters were defined by a Latin-hypercube sampling approach. Simulation results were summarized as a quantitative probabilistic hazard map for ballistic projectiles. Transects were also done in order to depict aerial hazard zones based on the same probabilistic procedure. Both maps combined can be used as a hazard prevention tool for ground and aerial transits nearby unresting volcanoes.

Applications of computational modeling in ballistics

NASA Technical Reports Server (NTRS)

Sturek, Walter B.

1987-01-01

The development of the technology of ballistics as applied to gun launched Army weapon systems is the main objective of research at the U.S. Army Ballistic Research Laboratory (BRL). The primary research programs at the BRL consist of three major ballistic disciplines: exterior, interior, and terminal. The work done at the BRL in these areas was traditionally highly dependent on experimental testing. A considerable emphasis was placed on the development of computational modeling to augment the experimental testing in the development cycle; however, the impact of the computational modeling to this date is modest. With the availability of supercomputer computational resources recently installed at the BRL, a new emphasis on the application of computational modeling to ballistics technology is taking place. The major application areas are outlined which are receiving considerable attention at the BRL at present and to indicate the modeling approaches involved. An attempt was made to give some information as to the degree of success achieved and indicate the areas of greatest need.

Heterogeneous propellant internal ballistics: criticism and regeneration

NASA Astrophysics Data System (ADS)

Glick, R. L.

2011-10-01

Although heterogeneous propellant and its innately nondeterministic, chemically discrete morphology dominates applications, ballisticcharacterization deterministic time-mean burning rate and acoustic admittance measures' absence of explicit, nondeterministic information requires homogeneous propellant with a smooth, uniformly regressing burning surface: inadequate boundary conditions for heterogeneous propellant grained applications. The past age overcame this dichotomy with one-dimensional (1D) models and empirical knowledge from numerous, adequately supported motor developments and supplementary experiments. However, current cost and risk constraints inhibit this approach. Moreover, its fundamental science approach is more sensitive to incomplete boundary condition information (garbage-in still equals garbage-out) and more is expected. This work critiques this situation and sketches a path forward based on enhanced ballistic and motor characterizations in the workplace and approximate model and apparatus developments mentored by CSAR DNS capabilities (or equivalent).

Hybrid Composite Laminates Reinforced with Kevlar/Carbon/Glass Woven Fabrics for Ballistic Impact Testing

PubMed Central

Randjbaran, Elias; Zahari, Rizal; Abdul Jalil, Nawal Aswan; Abang Abdul Majid, Dayang Laila

2014-01-01

Current study reported a facile method to investigate the effects of stacking sequence layers of hybrid composite materials on ballistic energy absorption by running the ballistic test at the high velocity ballistic impact conditions. The velocity and absorbed energy were accordingly calculated as well. The specimens were fabricated from Kevlar, carbon, and glass woven fabrics and resin and were experimentally investigated under impact conditions. All the specimens possessed equal mass, shape, and density; nevertheless, the layers were ordered in different stacking sequence. After running the ballistic test at the same conditions, the final velocities of the cylindrical AISI 4340 Steel pellet showed how much energy was absorbed by the samples. The energy absorption of each sample through the ballistic impact was calculated; accordingly, the proper ballistic impact resistance materials could be found by conducting the test. This paper can be further studied in order to characterise the material properties for the different layers. PMID:24955400

Quantum Mechanical Modeling of Ballistic MOSFETs

NASA Technical Reports Server (NTRS)

Svizhenko, Alexei; Anantram, M. P.; Govindan, T. R.; Biegel, Bryan (Technical Monitor)

2001-01-01

The objective of this project was to develop theory, approximations, and computer code to model quasi 1D structures such as nanotubes, DNA, and MOSFETs: (1) Nanotubes: Influence of defects on ballistic transport, electro-mechanical properties, and metal-nanotube coupling; (2) DNA: Model electron transfer (biochemistry) and transport experiments, and sequence dependence of conductance; and (3) MOSFETs: 2D doping profiles, polysilicon depletion, source to drain and gate tunneling, understand ballistic limit.

Sensor Fusion of Gaussian Mixtures for Ballistic Target Tracking in the Re-Entry Phase

PubMed Central

Lu, Kelin; Zhou, Rui

2016-01-01

A sensor fusion methodology for the Gaussian mixtures model is proposed for ballistic target tracking with unknown ballistic coefficients. To improve the estimation accuracy, a track-to-track fusion architecture is proposed to fuse tracks provided by the local interacting multiple model filters. During the fusion process, the duplicate information is removed by considering the first order redundant information between the local tracks. With extensive simulations, we show that the proposed algorithm improves the tracking accuracy in ballistic target tracking in the re-entry phase applications. PMID:27537883

Sensor Fusion of Gaussian Mixtures for Ballistic Target Tracking in the Re-Entry Phase.

PubMed

Lu, Kelin; Zhou, Rui

2016-08-15

A sensor fusion methodology for the Gaussian mixtures model is proposed for ballistic target tracking with unknown ballistic coefficients. To improve the estimation accuracy, a track-to-track fusion architecture is proposed to fuse tracks provided by the local interacting multiple model filters. During the fusion process, the duplicate information is removed by considering the first order redundant information between the local tracks. With extensive simulations, we show that the proposed algorithm improves the tracking accuracy in ballistic target tracking in the re-entry phase applications.

Modeling and Simulation of Ballistic Penetration of Ceramic-Polymer-Metal Layered Systems

DTIC Science & Technology

2016-01-01

ARL-RP-0562 ● JAN 2016 US Army Research Laboratory Modeling and Simulation of Ballistic Penetration of Ceramic-Polymer-Metal...manufacturer’s or trade names does not constitute an official endorsement or approval of the use thereof. Destroy this report when it is no longer needed...Do not return it to the originator. ARL-RP-0562 ● JAN 2016 US Army Research Laboratory Modeling and Simulation of Ballistic

Drag of ballistic electrons by an ion beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gurevich, V. L.; Muradov, M. I., E-mail: mag.muradov@mail.ioffe.ru

2015-12-15

Drag of electrons of a one-dimensional ballistic nanowire by a nearby one-dimensional beam of ions is considered. We assume that the ion beam is represented by an ensemble of heavy ions of the same velocity V. The ratio of the drag current to the primary current carried by the ion beam is calculated. The drag current turns out to be a nonmonotonic function of velocity V. It has a sharp maximum for V near v{sub nF}/2, where n is the number of the uppermost electron miniband (channel) taking part in conduction and v{sub nF} is the corresponding Fermi velocity. Thismore » means that the phenomenon of ion beam drag can be used for investigation of the electron spectra of ballistic nanostructures. We note that whereas observation of the Coulomb drag between two parallel quantum wires may in general be complicated by phenomena such as tunneling and phonon drag, the Coulomb drag of electrons of a one-dimensional ballistic nanowire by an ion beam is free of such spurious effects.« less

Diffusive and inelastic scattering in ballistic-electron-emission spectroscopy and ballistic-electron-emission microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, E.Y.; Turner, B.R.; Schowalter, L.J.

1993-07-01

Ballistic-electron-emission microscopy (BEEM) of Au/Si(001) n type was done to study whether elastic scattering in the Au overlayer is dominant. It was found that there is no dependence of the BEEM current on the relative gradient of the Au surface with respect to the Si interface, and this demonstrates that significant elastic scattering must occur in the Au overlayer. Ballistic-electron-emission spectroscopy (BEES) was also done, and, rather than using the conventional direct-current BEES, alternating-current (ac) BEES was done on Au/Si and also on Au/PtSi/Si(001) n type. The technique of ac BEES was found to give linear threshold for the Schottkymore » barrier, and it also clearly showed the onset of electron-hole pair creation and other inelastic scattering events. The study of device quality PtSi in Au/PtSi/Si(001) yielded an attenuation length of 4 nm for electrons of energy 1 eV above the PtSi Fermi energy. 20 refs., 5 figs.« less

Self-consistent Monte Carlo study of high-field carrier transport in graded heterostructures

NASA Astrophysics Data System (ADS)

Al-Omar, A.; Krusius, J. P.

1987-11-01

Hot-electron transport over graded heterostructures was investigated. A new formulation of the carrier transport, based on the effective mass theorem, a position-dependent Hamiltonian, scattering rates that included overlap integrals with correct symmetry, and ohmic contact models preserving the stochastic nature of carrier injection, was developed and implemented into the self-consistent ensemble Monte Carlo method. Hot-carrier transport in a graded Al(x)Ga(1-x)As device was explored with the following results: (1) the transport across compositionally graded semiconductor structures cannot be described with drift and diffusion concepts; (2) although heterostructure launchers generate a ballistic electron fraction as high as 15 percent and 40 percent of the total electron population for 300 and 77 K, respectively, they simultaneously reduce macroscopic average currents and carrier velocities; and (3) the width of the ballistic electron distribution and the magnitude of the ballistic fraction are primarily determined by material parameters and operating voltages rather than details of the device structure.

A Simple Ballistic Material Model for Soda-Lime Glass

DTIC Science & Technology

2009-01-01

Author’s personal copy A simple ballistic material model for soda-lime glass M. Grujicic a,*, B. Pandurangan a, N. Coutris a, B.A. Cheeseman b, C...Transparent armor Material modeling Ballistic performance Soda-lime glass a b s t r a c t Various open-literature experimental findings pertaining...notwithstanding any other provision of law, no person shall be subject to a penalty for failing to comply with a collection of information if it does not

Effect of the Lateral Exospheric Transport on the Horizontal Hydrogen Distribution Near the Exobase of Mars

NASA Astrophysics Data System (ADS)

Chaufray, J.-Y.; Yelle, R. V.; Gonzalez-Galindo, F.; Forget, F.; Lopez-Valverde, M.; Leblanc, F.; Modolo, R.

2018-03-01

We simulate the hydrogen density near the exobase of Mars, using the 3-D Martian Global Circulation Model of Laboratoire de Météorologie Dynamique, coupled to an exospheric ballistic model to compute the downward ballistic flux. The simulated hydrogen distribution near the exobase obtained at two different seasons—Ls = 180° and Ls = 270°—is close to Zero Net Ballistic Flux equilibrium. In other words, the hydrogen density near the exobase adjusts to have a balance between the local upward ballistic and the downward ballistic flux due to a short lateral migration time in the exosphere compared to the vertical diffusion time. This equilibrium leads to a hydrogen density n near the exobase directly controlled by the exospheric temperature T by the relation nT5/2 = constant. This relation could be used to extend 1-D hydrogen exospheric model of Mars used to derive the hydrogen density and escape flux at Mars from Lyman-α observations to 3-D model based on observed or modeled exospheric temperature near the exobase, without increasing the number of free parameters.

On the effect of ballistic overflow on the temperature dependence of the quantum efficiency of InGaN/GaN multiple quantum well light-emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prudaev, I. A., E-mail: funcelab@gmail.com; Kopyev, V. V.; Romanov, I. S.

The dependences of the quantum efficiency of InGaN/GaN multiple quantum well light-emitting diodes on the temperature and excitation level are studied. The experiment is performed for two luminescence excitation modes. A comparison of the results obtained during photo- and electroluminescence shows an additional (to the loss associated with Auger recombination) low-temperature loss in the high-density current region. This causes inversion of the temperature dependence of the quantum efficiency at temperatures lower than 220–300 K. Analysis shows that the loss is associated with electron leakage from the light-emitting-diode active region. The experimental data are explained using the ballistic-overflow model. The simulationmore » results are in qualitative agreement with the experimental dependences of the quantum efficiency on temperature and current density.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, J.F.

The global proliferation of ballistic missiles and weapons of mass destruction (WMD) has become one of the most immediate and dangerous threats to U.S. national security. Ballistic missiles were used in four of the last six major wars. Some 190 missiles were fired by Iraqis over a six week period at Iranian cities in 1988, during the 'War of the Cities'. Iraq's firing of Scuds against coalition forces and Israel during the Gulf War provided a vivid reminder of the threat these weapons can present to the world community. During the 1980's, many Third World countries assigned a high prioritymore » to the acquisition of ballistic missiles. By 1991, more than 20 of these nations either possessed ballistic missiles or were attempting to obtain them. Today 43 nations possess ballistic missiles. Seventeen of these probably have a nuclear weapon capability, with 20 of them possessing also a chemical or biological capability. This paper seeks to: define the military challenge ballistic missiles represent; review current U.S. counter-proliferation and nonproliferation initiatives and, finally make recommendations on other potential methods or considerations to reduce ballistic missile proliferation.« less

Comparison of Non-Parabolic Hydrodynamic Simulations for Semiconductor Devices

NASA Technical Reports Server (NTRS)

Smith, A. W.; Brennan, K. F.

1996-01-01

Parabolic drift-diffusion simulators are common engineering level design tools for semiconductor devices. Hydrodynamic simulators, based on the parabolic band approximation, are becoming more prevalent as device dimensions shrink and energy transport effects begin to dominate device characteristic. However, band structure effects present in state-of-the-art devices necessitate relaxing the parabolic band approximation. This paper presents simulations of ballistic diodes, a benchmark device, of Si and GaAs using two different non-parabolic hydrodynamic formulations. The first formulation uses the Kane dispersion relationship in the derivation of the conservation equations. The second model uses a power law dispersion relation {(hk)(exp 2)/2m = xW(exp Y)}. Current-voltage relations show that for the ballistic diodes considered. the non-parabolic formulations predict less current than the parabolic case. Explanations of this will be provided by examination of velocity and energy profiles. At low bias, the simulations based on the Kane formulation predict greater current flow than the power law formulation. As the bias is increased this trend changes and the power law predicts greater current than the Kane formulation. It will be shown that the non-parabolicity and energy range of the hydrodynamic model based on the Kane dispersion relation are limited due to the binomial approximation which was utilized in the derivation.

Material Modeling and Ballistic-Resistance Analysis of Armor-Grade Composites Reinforced with High-Performance Fibers

DTIC Science & Technology

2009-12-01

CLASSIFICATION OF: A new ballistic material model for 0/90 cross-plied oriented ultra-high molecular weight (UHMW) polyethylene fiber-based armor...recently developed unit cell-based ballistic material model for the same class of composites (M. Grujicic, G. Arakere, T. 1. REPORT DATE (DD-MM-YYYY) 4...ABSTRACT UU c. THIS PAGE UU 2. REPORT TYPE New Reprint 17. LIMITATION OF ABSTRACT UU 15. NUMBER OF PAGES 5d. PROJECT NUMBER 5e. TASK NUMBER 5f

Material Modeling of Space Shuttle Leading Edge and External Tank Materials For Use in the Columbia Accident Investigation

NASA Technical Reports Server (NTRS)

Carney, Kelly; Melis, Matthew; Fasanella, Edwin L.; Lyle, Karen H.; Gabrys, Jonathan

2004-01-01

Upon the commencement of the analytical effort to characterize the impact dynamics and damage of the Space Shuttle Columbia leading edge due to External Tank insulating foam, the necessity of creating analytical descriptions of these materials became evident. To that end, material models were developed of the leading edge thermal protection system, Reinforced Carbon Carbon (RCC), and a low density polyurethane foam, BX-250. Challenges in modeling the RCC include its extreme brittleness, the differing behavior in compression and tension, and the anisotropic fabric layup. These effects were successfully included in LS-DYNA Material Model 58, *MAT_LAMINATED_ COMPOSITE_ FABRIC. The differing compression and tension behavior was modeled using the available damage parameters. Each fabric layer was given an integration point in the shell element, and was allowed to fail independently. Comparisons were made to static test data and coupon ballistic impact tests before being utilized in the full scale analysis. The foam's properties were typical of elastic automotive foams; and LS-DYNA Material Model 83, *MAT_FU_CHANG_FOAM, was successfully used to model its behavior. Material parameters defined included strain rate dependent stress-strain curves for both loading and un-loading, and for both compression and tension. This model was formulated with static test data and strain rate dependent test data, and was compared to ballistic impact tests on load-cell instrumented aluminum plates. These models were subsequently utilized in analysis of the Shuttle leading edge full scale ballistic impact tests, and are currently being used in the Return to Flight Space Shuttle re-certification effort.

Force-induced desorption of 3-star polymers: a self-avoiding walk model

NASA Astrophysics Data System (ADS)

Janse van Rensburg, E. J.; Whittington, S. G.

2018-05-01

We consider a simple cubic lattice self-avoiding walk model of 3-star polymers adsorbed at a surface and then desorbed by pulling with an externally applied force. We determine rigorously the free energy of the model in terms of properties of a self-avoiding walk, and show that the phase diagram includes four phases, namely a ballistic phase where the extension normal to the surface is linear in the length, an adsorbed phase and a mixed phase, in addition to the free phase where the model is neither adsorbed nor ballistic. In the adsorbed phase all three branches or arms of the star are adsorbed at the surface. In the ballistic phase two arms of the star are pulled into a ballistic phase, while the remaining arm is in a free phase. In the mixed phase two arms in the star are adsorbed while the third arm is ballistic. The phase boundaries separating the ballistic and mixed phases, and the adsorbed and mixed phases, are both first order phase transitions. The presence of the mixed phase is interesting because it does not occur for pulled, adsorbed self-avoiding walks. In an atomic force microscopy experiment it would appear as an additional phase transition as a function of force.

Mathematical model and software for investigation of internal ballistic processes in high-speed projectile installations

NASA Astrophysics Data System (ADS)

Diachkovskii, A. S.; Zykova, A. I.; Ishchenko, A. N.; Kasimov, V. Z.; Rogaev, K. S.; Sidorov, A. D.

2017-11-01

This paper describes a software package that allows to explore the interior ballistics processes occurring in a shot scheme with bulk charges using propellant pasty substances at various loading schemes, etc. As a mathematical model, a model of a polydisperse mixture of non-deformable particles and a carrier gas phase is used in the quasi-one-dimensional approximation. Writing the equations of the mathematical model allows to use it to describe a broad class of interior ballistics processes. Features of the using approach are illustrated by calculating the ignition period for the charge of tubular propellant.

Dual-hemisphere transcranial direct current stimulation over primary motor cortex enhances consolidation of a ballistic thumb movement.

PubMed

Koyama, Soichiro; Tanaka, Satoshi; Tanabe, Shigeo; Sadato, Norihiro

2015-02-19

Transcranial direct current stimulation (tDCS) is a noninvasive technique that modulates motor performance and learning. Previous studies have shown that tDCS over the primary motor cortex (M1) can facilitate consolidation of various motor skills. However, the effect of tDCS on consolidation of newly learned ballistic movements remains unknown. The present study tested the hypothesis that tDCS over M1 enhances consolidation of ballistic thumb movements in healthy adults. Twenty-eight healthy subjects participated in an experiment with a single-blind, sham-controlled, between-group design. Fourteen subjects practiced a ballistic movement with their left thumb during dual-hemisphere tDCS. Subjects received 1mA anodal tDCS over the contralateral M1 and 1mA cathodal tDCS over the ipsilateral M1 for 25min during the training session. The remaining 14 subjects underwent identical training sessions, except that dual-hemisphere tDCS was applied for only the first 15s (sham group). All subjects performed the task again at 1h and 24h later. Primary measurements examined improvement in peak acceleration of the ballistic thumb movement at 1h and 24h after stimulation. Improved peak acceleration was significantly greater in the tDCS group (144.2±15.1%) than in the sham group (98.7±9.1%) (P<0.05) at 24h, but not 1h, after stimulation. Thus, dual-hemisphere tDCS over M1 enhanced consolidation of ballistic thumb movement in healthy adults. Dual-hemisphere tDCS over M1 may be useful to improve elemental motor behaviors, such as ballistic movements, in patients with subcortical strokes. Copyright © 2014 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

Hydrodynamic-to-ballistic crossover in Dirac materials

NASA Astrophysics Data System (ADS)

Svintsov, D.

2018-03-01

We develop an analytically solvable classical kinetic model of spatially dispersive transport in Dirac materials accounting for strong electron-electron (e-e) and electron-hole (e-h) collisions. We use this model to track the evolution of graphene conductivity and properties of its collective excitations across the hydrodynamic-to-ballistic crossover. We find the relaxation rate of electric current by e-e collisions that is possible due to the lack of Galilean invariance and introduce a universal numerical measure of this noninvariance. We find the two branches of collective excitations in the Dirac fluid: plasmons and electron-hole sound. The sound waves persist at frequencies exceeding the e-e collision frequency, have a small viscous damping at the neutrality point, but acquire large damping due to e-h friction even at slight doping. On the contrary, plasmons acquire strong frictional damping at the neutrality point and become well defined in doped samples.

Interior and exterior ballistics coupled optimization with constraints of attitude control and mechanical-thermal conditions

NASA Astrophysics Data System (ADS)

Liang, Xin-xin; Zhang, Nai-min; Zhang, Yan

2016-07-01

For solid launch vehicle performance promotion, a modeling method of interior and exterior ballistics associated optimization with constraints of attitude control and mechanical-thermal condition is proposed. Firstly, the interior and external ballistic models of the solid launch vehicle are established, and the attitude control model of the high wind area and the stage of the separation is presented, and the load calculation model of the drag reduction device is presented, and thermal condition calculation model of flight is presented. Secondly, the optimization model is established to optimize the range, which has internal and external ballistic design parameters as variables selected by sensitivity analysis, and has attitude control and mechanical-thermal conditions as constraints. Finally, the method is applied to the optimal design of a three stage solid launch vehicle simulation with differential evolution algorithm. Simulation results are shown that range capability is improved by 10.8%, and both attitude control and mechanical-thermal conditions are satisfied.

Schottky barrier height measurements of Cu/Si(001), Ag/Si(001), and Au/Si(001) interfaces utilizing ballistic electron emission microscopy and ballistic hole emission microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balsano, Robert; Matsubayashi, Akitomo; LaBella, Vincent P., E-mail: vlabella@albany.edu

2013-11-15

The Schottky barrier heights of both n and p doped Cu/Si(001), Ag/Si(001), and Au/Si(001) diodes were measured using ballistic electron emission microscopy and ballistic hole emission microscopy (BHEM), respectively. Measurements using both forward and reverse ballistic electron emission microscopy (BEEM) and (BHEM) injection conditions were performed. The Schottky barrier heights were found by fitting to a linearization of the power law form of the Bell-Kaiser BEEM model. The sum of the n-type and p-type barrier heights are in good agreement with the band gap of silicon and independent of the metal utilized. The Schottky barrier heights are found to bemore » below the region of best fit for the power law form of the BK model, demonstrating its region of validity.« less

Spin Seebeck effect and ballistic transport of quasi-acoustic magnons in room-temperature yttrium iron garnet films

NASA Astrophysics Data System (ADS)

Noack, Timo B.; Musiienko-Shmarova, Halyna Yu; Langner, Thomas; Heussner, Frank; Lauer, Viktor; Heinz, Björn; Bozhko, Dmytro A.; Vasyuchka, Vitaliy I.; Pomyalov, Anna; L’vov, Victor S.; Hillebrands, Burkard; Serga, Alexander A.

2018-06-01

We studied the transient behavior of the spin current generated by the longitudinal spin Seebeck effect (LSSE) in a set of platinum-coated yttrium iron garnet (YIG) films of different thicknesses. The LSSE was induced by means of pulsed microwave heating of the Pt layer and the spin currents were measured electrically using the inverse spin Hall effect in the same layer. We demonstrate that the time evolution of the LSSE is determined by the evolution of the thermal gradient triggering the flux of thermal magnons in the vicinity of the YIG/Pt interface. These magnons move ballistically within the YIG film with a constant group velocity, while their number decays exponentially within an effective propagation length. The ballistic flight of the magnons with energies above 20 K is a result of their almost linear dispersion law, similar to that of acoustic phonons. By fitting the time-dependent LSSE signal for different film thicknesses varying by almost an order of magnitude, we found that the effective propagation length is practically independent of the YIG film thickness. We consider this fact as strong support of a ballistic transport scenario—the ballistic propagation of quasi-acoustic magnons in room temperature YIG.

Combined Structural and Compositional Evolution of Planetary Rings Due to Micrometeoroid Impacts and Ballistic Transport

NASA Technical Reports Server (NTRS)

Estrada, Paul R.; Durisen, Richard H.; Cuzzi, Jeffrey N.; Morgan, Demitri A.

2015-01-01

We introduce improved numerical techniques for simulating the structural and compositional evolution of planetary rings due to micrometeoroid bombardment and subsequent ballistic transport of impact ejecta. Our current, robust code is capable of modeling structural changes and pollution transport simultaneously over long times on both local and global scales. In this paper, we describe the methodology based on the original structural code of Durisen et al. (1989, Icarus 80, 136-166) and on the pollution transport code of Cuzzi and Estrada (1998, Icarus 132, 1-35). We provide demonstrative simulations to compare with, and extend upon previous work, as well as examples of how ballistic transport can maintain the observed structure in Saturn's rings using available Cassini occultation optical depth data. In particular, we explicitly verify the claim that the inner B (and presumably A) ring edge can be maintained over long periods of time due to an ejecta distribution that is heavily biased in the prograde direction through a balance between the sharpening effects of ballistic transport and the broadening effects of viscosity. We also see that a "ramp"-like feature forms over time just inside that edge. However, it does not remain linear for the duration of the runs presented here unless a less steep ejecta velocity distribution is adopted. We also model the C ring plateaus and find that their outer edges can be maintained at their observed sharpness for long periods due to ballistic transport. We hypothesize that the addition of a significant component of a retrograde-biased ejecta distribution may help explain the linearity of the ramp and is probably essential for maintaining the sharpness of C ring plateau inner edges. This component would arise for the subset of micrometeoroid impacts which are destructive rather than merely cratering. Such a distribution will be introduced in future work.

Combined structural and compositional evolution of planetary rings due to micrometeoroid impacts and ballistic transport

NASA Astrophysics Data System (ADS)

Estrada, Paul R.; Durisen, Richard H.; Cuzzi, Jeffrey N.; Morgan, Demitri A.

2015-05-01

We introduce improved numerical techniques for simulating the structural and compositional evolution of planetary rings due to micrometeoroid bombardment and subsequent ballistic transport of impact ejecta. Our current, robust code is capable of modeling structural changes and pollution transport simultaneously over long times on both local and global scales. In this paper, we describe the methodology based on the original structural code of Durisen et al. (Durisen, R.H. et al. [1989]. Icarus 80, 136-166) and on the pollution transport code of Cuzzi and Estrada (Cuzzi, J.N., Estrada, P.R. [1998]. Icarus 132, 1-35). We provide demonstrative simulations to compare with, and extend upon previous work, as well as examples of how ballistic transport can maintain the observed structure in Saturn's rings using available Cassini occultation optical depth data. In particular, we explicitly verify the claim that the inner B (and presumably A) ring edge can be maintained over long periods of time due to an ejecta distribution that is heavily biased in the prograde direction through a balance between the sharpening effects of ballistic transport and the broadening effects of viscosity. We also see that a "ramp"-like feature forms over time just inside that edge. However, it does not remain linear for the duration of the runs presented here unless a less steep ejecta velocity distribution is adopted. We also model the C ring plateaus and find that their outer edges can be maintained at their observed sharpness for long periods due to ballistic transport. We hypothesize that the addition of a significant component of a retrograde-biased ejecta distribution may help explain the linearity of the ramp and could provide a mechanism for maintaining the sharpness of C ring plateau inner edges. This component would arise for the subset of micrometeoroid impacts which are destructive rather than merely cratering. Such a distribution will be introduced in future work.

The Simplest Complete Model of Choice Response Time: Linear Ballistic Accumulation

ERIC Educational Resources Information Center

Brown, Scott D.; Heathcote, Andrew

2008-01-01

We propose a linear ballistic accumulator (LBA) model of decision making and reaction time. The LBA is simpler than other models of choice response time, with independent accumulators that race towards a common response threshold. Activity in the accumulators increases in a linear and deterministic manner. The simplicity of the model allows…

GPU based 3D feature profile simulation of high-aspect ratio contact hole etch process under fluorocarbon plasmas

NASA Astrophysics Data System (ADS)

Chun, Poo-Reum; Lee, Se-Ah; Yook, Yeong-Geun; Choi, Kwang-Sung; Cho, Deog-Geun; Yu, Dong-Hun; Chang, Won-Seok; Kwon, Deuk-Chul; Im, Yeon-Ho

2013-09-01

Although plasma etch profile simulation has been attracted much interest for developing reliable plasma etching, there still exist big gaps between current research status and predictable modeling due to the inherent complexity of plasma process. As an effort to address this issue, we present 3D feature profile simulation coupled with well-defined plasma-surface kinetic model for silicon dioxide etching process under fluorocarbon plasmas. To capture the realistic plasma surface reaction behaviors, a polymer layer based surface kinetic model was proposed to consider the simultaneous polymer deposition and oxide etching. Finally, the realistic plasma surface model was used for calculation of speed function for 3D topology simulation, which consists of multiple level set based moving algorithm, and ballistic transport module. In addition, the time consumable computations in the ballistic transport calculation were improved drastically by GPU based numerical computation, leading to the real time computation. Finally, we demonstrated that the surface kinetic model could be coupled successfully for 3D etch profile simulations in high-aspect ratio contact hole plasma etching.

Movement Integration and the One-Target Advantage.

PubMed

Hoffmann, Errol R

2017-01-01

The 1-target advantage (OTA) has been found to occur in many circumstances and the current best explanation for this phenomenon is that of the movement integration hypothesis. The author's purpose is twofold: (a) to model the conditions under which there is integration of the movement components in a 2-component movement and (b) to study the factors that determine the magnitude of the OTA for both the first and second component of a 2-component movement. Results indicate that integration of movement components, where times for one component are affected by the geometry of the other component, occurs when 1 of the movement components is made ballistically. Movement components that require ongoing visual control show only weak interaction with the second component, whereas components made ballistically always show movement time dependence on first and second component amplitude, independent of location within the sequence. The OTA is present on both the first and second components of the movement, with a magnitude that is dependent on whether the components are performed ballistically or with ongoing visual control and also on the amplitudes and indexes of difficulty of the component movements.

Dynamic Load Measurement of Ballistic Gelatin Impact Using an Instrumented Tube

NASA Technical Reports Server (NTRS)

Seidt, J. D.; Periira, J. M.; Hammer, J. T.; Gilat, A.; Ruggeri, C. R.

2012-01-01

Bird strikes are a common problem for the aerospace industry and can cause serious damage to an aircraft. Ballistic gelatin is frequently used as a surrogate for actual bird carcasses in bird strike tests. Numerical simulations of these tests are used to supplement experimental data, therefore it is necessary to use numerical modeling techniques that can accurately capture the dynamic response of ballistic gelatin. An experimental technique is introduced to validate these modeling techniques. A ballistic gelatin projectile is fired into a strike plate attached to a 36 in. long sensor tube. Dynamic load is measured at two locations relative to the strike plate using strain gages configured in a full Wheatstone bridge. Data from these experiments are used to validate a gelatin constitutive model. Simulations of the apparatus are analyzed to investigate its performance.

Buildings vs. ballistics: Quantifying the vulnerability of buildings to volcanic ballistic impacts using field studies and pneumatic cannon experiments

NASA Astrophysics Data System (ADS)

Williams, G. T.; Kennedy, B. M.; Wilson, T. M.; Fitzgerald, R. H.; Tsunematsu, K.; Teissier, A.

2017-09-01

Recent casualties in volcanic eruptions due to trauma from blocks and bombs necessitate more rigorous, ballistic specific risk assessment. Quantitative assessments are limited by a lack of experimental and field data on the vulnerability of buildings to ballistic hazards. An improved, quantitative understanding of building vulnerability to ballistic impacts is required for informing appropriate life safety actions and other risk reduction strategies. We assessed ballistic impacts to buildings from eruptions at Usu Volcano and Mt. Ontake in Japan and compiled available impact data from eruptions elsewhere to identify common damage patterns from ballistic impacts to buildings. We additionally completed a series of cannon experiments which simulate ballistic block impacts to building claddings to investigate their performance over a range of ballistic projectile velocities, masses and energies. Our experiments provide new insights by quantifying (1) the hazard associated with post-impact shrapnel from building and rock fragments; (2) the effect of impact obliquity on damage; and (3) the additional impact resistance buildings possess when claddings are struck in areas directly supported by framing components. This was not well identified in previous work which may have underestimated building vulnerability to ballistic hazards. To improve assessment of building vulnerability to ballistics, we use our experimental and field data to develop quantitative vulnerability models known as fragility functions. Our fragility functions and field studies show that although unreinforced buildings are highly vulnerable to large ballistics (> 20 cm diameter), they can still provide shelter, preventing death during eruptions.

Hazard map for volcanic ballistic impacts at Popocatépetl volcano (Mexico)

NASA Astrophysics Data System (ADS)

Alatorre-Ibargüengoitia, Miguel A.; Delgado-Granados, Hugo; Dingwell, Donald B.

2012-11-01

During volcanic explosions, volcanic ballistic projectiles (VBP) are frequently ejected. These projectiles represent a threat to people, infrastructure, vegetation, and aircraft due to their high temperatures and impact velocities. In order to protect people adequately, it is necessary to delimit the projectiles' maximum range within well-defined explosion scenarios likely to occur in a particular volcano. In this study, a general methodology to delimit the hazard zones for VBP during volcanic eruptions is applied to Popocatépetl volcano. Three explosion scenarios with different intensities have been defined based on the past activity of the volcano and parameterized by considering the maximum kinetic energy associated with VBP ejected during previous eruptions. A ballistic model is used to reconstruct the "launching" kinetic energy of VBP observed in the field. In the case of Vulcanian eruptions, the most common type of activity at Popocatépetl, the ballistic model was used in concert with an eruptive model to correlate ballistic range with initial pressure and gas content, parameters that can be estimated by monitoring techniques. The results are validated with field data and video observations of different Vulcanian eruptions at Popocatépetl. For each scenario, the ballistic model is used to calculate the maximum range of VBP under optimum "launching" conditions: ballistic diameter, ejection angle, topography, and wind velocity. Our results are presented in the form of a VBP hazard map with topographic profiles that depict the likely maximum ranges of VBP under explosion scenarios defined specifically for Popocatépetl volcano. The hazard zones shown on the map allow the responsible authorities to plan the definition and mitigation of restricted areas during volcanic crises.

Model of ballistic targets' dynamics used for trajectory tracking algorithms

NASA Astrophysics Data System (ADS)

Okoń-FÄ fara, Marta; Kawalec, Adam; Witczak, Andrzej

2017-04-01

There are known only few ballistic object tracking algorithms. To develop such algorithms and to its further testing, it is necessary to implement possibly simple and reliable objects' dynamics model. The article presents the dynamics' model of a tactical ballistic missile (TBM) including the three stages of flight: the boost stage and two passive stages - the ascending one and the descending one. Additionally, the procedure of transformation from the local coordinate system to the polar-radar oriented and the global is presented. The prepared theoretical data may be used to determine the tracking algorithm parameters and to its further verification.

Surface morphology of a modified ballistic deposition model.

PubMed

Banerjee, Kasturi; Shamanna, J; Ray, Subhankar

2014-08-01

The surface and bulk properties of a modified ballistic deposition model are investigated. The deposition rule interpolates between nearest- and next-nearest-neighbor ballistic deposition and the random deposition models. The stickiness of the depositing particle is controlled by a parameter and the type of interparticle force. Two such forces are considered: Coulomb and van der Waals type. The interface width shows three distinct growth regions before eventual saturation. The rate of growth depends more strongly on the stickiness parameter than on the type of interparticle force. However, the porosity of the deposits is strongly influenced by the interparticle force.

Ballistic damage in hybrid composite laminates

NASA Astrophysics Data System (ADS)

Phadnis, Vaibhav A.; Pandya, Kedar S.; Naik, Niranjan K.; Roy, Anish; Silberschmidt, Vadim V.

2015-07-01

Ballistic damage of hybrid woven-fabric composites made of plain-weave E-glass- fabric/epoxy and 8H satin-weave T300 carbon-fabric/epoxy is studied using a combination of experimental tests, microstructural studies and finite-element (FE) analysis. Ballistic tests were conducted with a single-stage gas gun. Fibre damage and delamination were observed to be dominating failure modes. A ply-level FE model was developed, with a fabric-reinforced ply modelled as a homogeneous orthotropic material with capacity to sustain progressive stiffness degradation due to fibre/matrix cracking, fibre breaking and plastic deformation under shear loading. Simulated damage patterns on the front and back faces of fabric-reinforced composite plates provided an insight into their damage mechanisms under ballistic loading.

Thermo-Electron Ballistic Coolers or Heaters

NASA Technical Reports Server (NTRS)

Choi, Sang H.

2003-01-01

Electronic heat-transfer devices of a proposed type would exploit some of the quantum-wire-like, pseudo-superconducting properties of single-wall carbon nanotubes or, optionally, room-temperature-superconducting polymers (RTSPs). The devices are denoted thermo-electron ballistic (TEB) coolers or heaters because one of the properties that they exploit is the totally or nearly ballistic (dissipation or scattering free) transport of electrons. This property is observed in RTSPs and carbon nanotubes that are free of material and geometric defects, except under conditions in which oscillatory electron motions become coupled with vibrations of the nanotubes. Another relevant property is the high number density of electrons passing through carbon nanotubes -- sufficient to sustain electron current densities as large as 100 MA/square cm. The combination of ballistic motion and large current density should make it possible for TEB devices to operate at low applied potentials while pumping heat at rates several orders of magnitude greater than those of thermoelectric devices. It may also enable them to operate with efficiency close to the Carnot limit. In addition, the proposed TEB devices are expected to operate over a wider temperature range

Orion Parachute Riser Cutter Development

NASA Technical Reports Server (NTRS)

Oguz, Sirri; Salazar, Frank

2011-01-01

This paper presents the tests and analytical approach used on the development of a steel riser cutter for the CEV Parachute Assembly System (CPAS) used on the Orion crew module. Figure 1 shows the riser cutter and the steel riser bundle which consists of six individual cables. Due to the highly compressed schedule, initial unavailability of the riser material and the Orion Forward Bay mechanical constraints, JSC primarily relied on a combination of internal ballistics analysis and LS-DYNA simulation for this project. Various one dimensional internal ballistics codes that use standard equation of state and conservation of energy have commonly used in the development of CAD devices for initial first order estimates and as an enhancement to the test program. While these codes are very accurate for propellant performance prediction, they usually lack a fully defined kinematic model for dynamic predictions. A simple piston device can easily and accurately be modeled using an equation of motion. However, the accuracy of analytical models is greatly reduced on more complicated devices with complex external loads, nonlinear trajectories or unique unlocking features. A 3D finite element model of CAD device with all critical features included can vastly improve the analytical ballistic predictions when it is used as a supplement to the ballistic code. During this project, LS-DYNA structural 3D model was used to predict the riser resisting load that was needed for the ballistic code. A Lagrangian model with eroding elements shown in Figure 2 was used for the blade, steel riser and the anvil. The riser material failure strain was fine tuned by matching the dent depth on the anvil with the actual test data. LS-DYNA model was also utilized to optimize the blade tip design for the most efficient cut. In parallel, the propellant type and the amount were determined by using CADPROG internal ballistics code. Initial test results showed a good match with LS-DYNA and CADPROG simulations. Final paper will present a detailed roadmap from initial ballistic modeling and LS-DYNA simulation to the performance testing. Blade shape optimization study will also be presented.

Temperature dependence of ballistic mobility in a metamorphic InGaAs/InAlAs high electron mobility transistor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Jongkyong; Gang, Suhyun; Jo, Yongcheol

We have investigated the temperature dependence of ballistic mobility in a 100 nm-long InGaAs/InAlAs metamorphic high-electron-mobility transistor designed for millimeter-wavelength RF applications. To extract the temperature dependence of quasi-ballistic mobility, our experiment involves measurements of the effective mobility in the low-bias linear region of the transistor and of the collision-dominated Hall mobility using a gated Hall bar of the same epitaxial structure. The data measured from the experiment are consistent with that of modeled ballistic mobility based on ballistic transport theory. These results advance the understanding of ballistic transport in various transistors with a nano-scale channel length that is comparable tomore » the carrier's mean free path in the channel.« less

Unconventional transport in ultraclean graphene constriction devices

NASA Astrophysics Data System (ADS)

Pita Vidal, Marta; Ma, Qiong; Watanabe, Kenji; Taniguchi, Takashi; Jarillo-Herrero, Pablo

Under mesoscopic conditions, strong electron-electron interactions and weak electron-phonon coupling in graphene lead to hydrodynamic behavior of electrons, resulting in unusual and unexpected transport phenomena. Specifically, this hydrodynamical collective cooperation of electrons is predicted to enhance the flow of electrical current, leading to a striking higher-than-ballistic conductance through a narrow geometrical constriction. To access the hydrodynamic regime, we fabricated high-quality, low-disorder graphene nano-constriction devices encapsulated by hexagonal boron nitride, where electron-electron scattering dominates impurity scattering. We will report on our systematic four-probe conductance measurements on devices with different constriction widths as a function of number density and temperature. The observation of quantum transport phenomena that are inconsistent with the non-interacting ballistic free-fermion model would suggest a macroscopic transport signature of electron viscosity.

26th International Symposium on Ballistics

DTIC Science & Technology

2011-09-16

judicious use of analytical predictions correlated with ballistic testing and post - test failure morphology investigations. •Our approach...ballistic predictions. The numerical predictions correlate well with the damage pattern. Post - Test Morphology Simulation Imbedded Steel Plate Removed Post ... Test •Numerical simulation of damage to embedded steel plate compares well with the post - test plate morphology •Multi-strike modeling in work

Analysis of pressure blips in aft-finocyl solid rocket motor

NASA Astrophysics Data System (ADS)

Di Giacinto, M.; Favini, B.; Cavallini, E.

2016-07-01

Ballistic anomalies have frequently occurred during the firing of several solid rocket motors (SRMs) (Inertial Upper Stage, Space Shuttle Redesigned SRM (RSRM) and Titan IV SRM Upgrade (SRMU)), producing even relevant and unexpected variations of the SRM pressure trace from its nominal profile. This paper has the purpose to provide a numerical analysis of the following possible causes of ballistic anomalies in SRMs: an inert object discharge, a slag ejection, and an unexpected increase in the propellant burning rate or in the combustion surface. The SRM configuration under investigation is an aft-finocyl SRM with a first-stage/small booster design. The numerical simulations are performed with a quasi-one-dimensional (Q1D) unsteady model of the SRM internal ballistics, properly tailored to model each possible cause of the ballistic anomalies. The results have shown that a classification based on the head-end pressure (HEP) signature, relating each other the HEP shape and the ballistic anomaly cause, can be made. For each cause of ballistic anomalies, a deepened discussion of the parameters driving the HEP signatures is provided, as well as qualitative and quantitative assessments of the resultant pressure signals.

High Resolution, High-Speed Photography, an Increasingly Prominent Diagnostic in Ballistic Research Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, L.; Muelder, S.

1999-10-22

High resolution, high-speed photography is becoming a prominent diagnostic in ballistic experimentation. The development of high speed cameras utilizing electro-optics and the use of lasers for illumination now provide the capability to routinely obtain high quality photographic records of ballistic style experiments. The purpose of this presentation is to review in a visual manner the progress of this technology and how it has impacted ballistic experimentation. Within the framework of development at LLNL, we look at the recent history of large format high-speed photography, and present a number of photographic records that represent the state of the art at themore » time they were made. These records are primarily from experiments involving shaped charges. We also present some examples of current photographic technology, developed within the ballistic community, that has application to hydro diagnostic experimentation at large. This paper is designed primarily as an oral-visual presentation. This written portion is to provide general background, a few examples, and a bibliography.« less

Ballistic edge states in Bismuth nanowires revealed by SQUID interferometry

PubMed Central

Murani, Anil; Kasumov, Alik; Sengupta, Shamashis; Kasumov, Yu A.; Volkov, V. T.; Khodos, I. I.; Brisset, F.; Delagrange, Raphaëlle; Chepelianskii, Alexei; Deblock, Richard; Bouchiat, Hélène; Guéron, Sophie

2017-01-01

The protection against backscattering provided by topology is a striking property. In two-dimensional insulators, a consequence of this topological protection is the ballistic nature of the one-dimensional helical edge states. One demonstration of ballisticity is the quantized Hall conductance. Here we provide another demonstration of ballistic transport, in the way the edge states carry a supercurrent. The system we have investigated is a micrometre-long monocrystalline bismuth nanowire with topological surfaces, that we connect to two superconducting electrodes. We have measured the relation between the Josephson current flowing through the nanowire and the superconducting phase difference at its ends, the current–phase relation. The sharp sawtooth-shaped phase-modulated current–phase relation we find demonstrates that transport occurs selectively along two ballistic edges of the nanowire. In addition, we show that a magnetic field induces 0–π transitions and φ0-junction behaviour, providing a way to manipulate the phase of the supercurrent-carrying edge states and generate spin supercurrents. PMID:28677681

Current nuclear threats and possible responses

NASA Astrophysics Data System (ADS)

Lamb, Frederick K.

2005-04-01

Over the last 50 years, the United States has spent more than 100 billion developing and building a variety of systems intended to defend its territory against intercontinental-range ballistic missiles. Most of these systems never became operational and ultimately all were judged ineffective. The United States is currently spending about 10 billion per year developing technologies and systems intended to defend against missiles that might be acquired in the future by North Korea or Iran. This presentation will discuss these efforts ad whether they are likely to be more effective than those of the past. It will also discuss the proper role of anti-ballistic programs at a time when the threat of a nuclear attack on the U.S. by terrorists armed with nuclear weapons is thought to be much higher than the threat of an attack by nuclear-armed ballistic missles.

Electron transport in ultra-thin films and ballistic electron emission microscopy

NASA Astrophysics Data System (ADS)

Claveau, Y.; Di Matteo, S.; de Andres, P. L.; Flores, F.

2017-03-01

We have developed a calculation scheme for the elastic electron current in ultra-thin epitaxial heterostructures. Our model uses a Keldysh’s non-equilibrium Green’s function formalism and a layer-by-layer construction of the epitaxial film. Such an approach is appropriate to describe the current in a ballistic electron emission microscope (BEEM) where the metal base layer is ultra-thin and generalizes a previous one based on a decimation technique appropriated for thick slabs. This formalism allows a full quantum mechanical description of the transmission across the epitaxial heterostructure interface, including multiple scattering via the Dyson equation, which is deemed a crucial ingredient to describe interfaces of ultra-thin layers properly in the future. We introduce a theoretical formulation needed for ultra-thin layers and we compare with results obtained for thick Au(1 1 1) metal layers. An interesting effect takes place for a width of about ten layers: a BEEM current can propagate via the center of the reciprocal space (\\overlineΓ ) along the Au(1 1 1) direction. We associate this current to a coherent interference finite-width effect that cannot be found using a decimation technique. Finally, we have tested the validity of the handy semiclassical formalism to describe the BEEM current.

Solid rocket booster performance evaluation model. Volume 3: Sample case. [propellant combustion simulation/internal ballistics

NASA Technical Reports Server (NTRS)

1974-01-01

The solid rocket booster performance evaluation model (SRB-11) is used to predict internal ballistics in a sample motor. This motor contains a five segmented grain. The first segment has a 14 pointed star configuration with a web which wraps partially around the forward dome. The other segments are circular in cross-section and are tapered along the interior burning surface. Two of the segments are inhibited on the forward face. The nozzle is not assumed to be submerged. The performance prediction is broken into two simulation parts: the delivered end item specific impulse and the propellant properties which are required as inputs for the internal ballistics module are determined; and the internal ballistics for the entire burn duration of the motor are simulated.

Ballistic transport in graphene Y-junctions in transverse electric field.

PubMed

Nemnes, G A; Mitran, T L; Dragoman, Daniela

2018-06-05

We investigate the prospects for current modulation in single layer graphene Y-junctions in the ballistic regime, under an external electric field. Overcoming the inability of inducing field effect in graphene nanoribbons by a stacked gate, the proposed in-plane electric field setup enables a controlled current transfer between the branches of the Y-junction. This behavior is further confirmed by changing the angular incidence of the electric field. The ballistic transmission functions are calculated for the three terminal system using the non-equilibrium Green's function formalism, in the framework of density functional theory, under finite bias conditions. The edge currents dominating the transport in zigzag nanoribbons are strongly influenced by the induced dipole charge, facilitating the current modulation even for the metallic-like character of the Y-junctions. Spin polarization effects indicate the possibility of achieving spin filtering even in the absence of the external field provided the antiferromagnetic couplings between the edges are asymptotically set. Overall, our results indicate a robust behavior regarding the tunability of the charge current in the two outlet ports, showing the possibility of inducing field effect control in a single layer graphene system.

Ergonomics assessment of composite ballistic inserts for bullet- and fragment-proof vests.

PubMed

Majchrzycka, Katarzyna; Brochocka, Agnieszka; Luczak, Anna; Lężak, Krzysztof

2013-01-01

Personal protective equipment worn by uniformed services (e.g., the police and the military) must ensure protection against bodily injuries. However, a high degree of protection is always associated with significant discomfort. This article presents the results of an assessment of the ergonomics parameters of new special purpose products, ballistic inserts with improved ballistic resistance, and an assessment of the impact of the burden related to their use on the psychomotor performance of the subjects. An obstacle course and subjective ergonomics assessment questionnaires were used in tests. Thermal discomfort was also assessed. Psychological testing included tests enabling an assessment of the subjects' cognitive and psychomotor performance, and a subjective assessment of mental load. The tests did not show any decrease in the comfort of use of the new inserts with improved ballistic resistance compared to the inserts currently used.

Planetary Moon Cycler Trajectories

NASA Technical Reports Server (NTRS)

Russell, Ryan P.; Strange, Nathan J.

2007-01-01

Free-return cycler trajectories repeatedly shuttle a spacecraft between two bodies using little or no fuel. Here, the cycler architecture is proposed as a complementary and alternative method for designing planetary moon tours. Previously applied enumerative cycler search and optimization techniques are generalized and specifically implemented in the Jovian and Saturnian moon systems. In addition, the algorithms are tested for general use to find non-Earth heliocentric cyclers. Overall, hundreds of ideal model ballistic cycler geometries are found and several representative cases are documented and discussed. Many of the ideal model solutions are found to remain ballistic in a zero radius sphere of influence patched conic ephemeris model, and preliminary work in a high-fidelity fully integrated model demonstrates near-ballistic cycles for several example cases.

Semi-Automated Trajectory Analysis of Deep Ballistic Penetrating Brain Injury

PubMed Central

Folio, Les; Solomon, Jeffrey; Biassou, Nadia; Fischer, Tatjana; Dworzak, Jenny; Raymont, Vanessa; Sinaii, Ninet; Wassermann, Eric M.; Grafman, Jordan

2016-01-01

Background Penetrating head injuries (PHIs) are common in combat operations and most have visible wound paths on computed tomography (CT). Objective We assess agreement between an automated trajectory analysis-based assessment of brain injury and manual tracings of encephalomalacia on CT. Methods We analyzed 80 head CTs with ballistic PHI from the Institutional Review Board approved Vietnam head injury registry. Anatomic reports were generated from spatial coordinates of projectile entrance and terminal fragment location. These were compared to manual tracings of the regions of encephalomalacia. Dice’s similarity coefficients, kappa, sensitivities, and specificities were calculated to assess agreement. Times required for case analysis were also compared. Results Results show high specificity of anatomic regions identified on CT with semiautomated anatomical estimates and manual tracings of tissue damage. Radiologist’s and medical students’ anatomic region reports were similar (Kappa 0.8, t-test p < 0.001). Region of probable injury modeling of involved brain structures was sensitive (0.7) and specific (0.9) compared with manually traced structures. Semiautomated analysis was 9-fold faster than manual tracings. Conclusion Our region of probable injury spatial model approximates anatomical regions of encephalomalacia from ballistic PHI with time-saving over manual methods. Results show potential for automated anatomical reporting as an adjunct to current practice of radiologist/neurosurgical review of brain injury by penetrating projectiles. PMID:23707123

Ballistic-Electron-Emission Microscope

NASA Technical Reports Server (NTRS)

Kaiser, William J.; Bell, L. Douglas

1990-01-01

Ballistic-electron-emission microscope (BEEM) employs scanning tunneling-microscopy (STM) methods for nondestructive, direct electrical investigation of buried interfaces, such as interface between semiconductor and thin metal film. In BEEM, there are at least three electrodes: emitting tip, biasing electrode, and collecting electrode, receiving current crossing interface under investigation. Signal-processing device amplifies electrode signals and converts them into form usable by computer. Produces spatial images of surface by scanning tip; in addition, provides high-resolution images of buried interface under investigation. Spectroscopic information extracted by measuring collecting-electrode current as function of one of interelectrode voltages.

Collective Poisson process with periodic rates: applications in physics from micro-to nanodevices.

PubMed

da Silva, Roberto; Lamb, Luis C; Wirth, Gilson Inacio

2011-01-28

Continuous reductions in the dimensions of semiconductor devices have led to an increasing number of noise sources, including random telegraph signals (RTS) due to the capture and emission of electrons by traps at random positions between oxide and semiconductor. The models traditionally used for microscopic devices become of limited validity in nano- and mesoscale systems since, in such systems, distributed quantities such as electron and trap densities, and concepts like electron mobility, become inadequate to model electrical behaviour. In addition, current experimental works have shown that RTS in semiconductor devices based on carbon nanotubes lead to giant current fluctuations. Therefore, the physics of this phenomenon and techniques to decrease the amplitudes of RTS need to be better understood. This problem can be described as a collective Poisson process under different, but time-independent, rates, τ(c) and τ(e), that control the capture and emission of electrons by traps distributed over the oxide. Thus, models that consider calculations performed under time-dependent periodic capture and emission rates should be of interest in order to model more efficient devices. We show a complete theoretical description of a model that is capable of showing a noise reduction of current fluctuations in the time domain, and a reduction of the power spectral density in the frequency domain, in semiconductor devices as predicted by previous experimental work. We do so through numerical integrations and a novel Monte Carlo Markov chain (MCMC) algorithm based on microscopic discrete values. The proposed model also handles the ballistic regime, relevant in nano- and mesoscale devices. Finally, we show that the ballistic regime leads to nonlinearity in the electrical behaviour.

Aerodynamics of the EXPERT Re-Entry Ballistic Vehicle

NASA Astrophysics Data System (ADS)

Kharitonov, A. M.; Adamov, N. P.; Mazhul, I. I.; Vasenyov, L. G.; Zvegintsev, V. I.; Muylaert, J. M.

2009-01-01

Since 2002 till now, experimental studies of the EXPERT reentry capsule have been performed in ITAM SB RAS wind tunnels. These studies have been performed in consecutive ISTC project No. 2109, 3151, and currently ongoing project No. 3550. The results of earlier studies in ITAM wind tunnels can be found in [1-4]. The present paper describes new data obtained for the EXPERT model.

One-Dimensional Modelling of Internal Ballistics

NASA Astrophysics Data System (ADS)

Monreal-González, G.; Otón-Martínez, R. A.; Velasco, F. J. S.; García-Cascáles, J. R.; Ramírez-Fernández, F. J.

2017-10-01

A one-dimensional model is introduced in this paper for problems of internal ballistics involving solid propellant combustion. First, the work presents the physical approach and equations adopted. Closure relationships accounting for the physical phenomena taking place during combustion (interfacial friction, interfacial heat transfer, combustion) are deeply discussed. Secondly, the numerical method proposed is presented. Finally, numerical results provided by this code (UXGun) are compared with results of experimental tests and with the outcome from a well-known zero-dimensional code. The model provides successful results in firing tests of artillery guns, predicting with good accuracy the maximum pressure in the chamber and muzzle velocity what highlights its capabilities as prediction/design tool for internal ballistics.

Bayes factors for the linear ballistic accumulator model of decision-making.

PubMed

Evans, Nathan J; Brown, Scott D

2018-04-01

Evidence accumulation models of decision-making have led to advances in several different areas of psychology. These models provide a way to integrate response time and accuracy data, and to describe performance in terms of latent cognitive processes. Testing important psychological hypotheses using cognitive models requires a method to make inferences about different versions of the models which assume different parameters to cause observed effects. The task of model-based inference using noisy data is difficult, and has proven especially problematic with current model selection methods based on parameter estimation. We provide a method for computing Bayes factors through Monte-Carlo integration for the linear ballistic accumulator (LBA; Brown and Heathcote, 2008), a widely used evidence accumulation model. Bayes factors are used frequently for inference with simpler statistical models, and they do not require parameter estimation. In order to overcome the computational burden of estimating Bayes factors via brute force integration, we exploit general purpose graphical processing units; we provide free code for this. This approach allows estimation of Bayes factors via Monte-Carlo integration within a practical time frame. We demonstrate the method using both simulated and real data. We investigate the stability of the Monte-Carlo approximation, and the LBA's inferential properties, in simulation studies.

Fortran Programs for Weapon Systems Analysis

DTIC Science & Technology

1990-06-01

interested in ballistics and related work. The programs include skeletal combat models , a set of discrete-event timing routines, mathematical and...32 4.3 LinEqs: Solve Linear Equations Like a Textbook ........................................................................... 34...military applications as it is of computer science. This crisis occurs in all fields, including the modeling of logistics, mobility, ballistics, and combat

Fake ballistics and real explosions: field-scale experiments on the ejection and emplacement of volcanic bombs during vent-clearing explosive activity

NASA Astrophysics Data System (ADS)

Taddeucci, J.; Valentine, G.; Gaudin, D.; Graettinger, A. H.; Lube, G.; Kueppers, U.; Sonder, I.; White, J. D.; Ross, P.; Bowman, D. C.

2013-12-01

Ballistics - bomb-sized pyroclasts that travel from volcanic source to final emplacement position along ballistic trajectories - represent a prime source of volcanic hazard, but their emplacement range, size, and density is useful to inverse model key eruption parameters related to their initial ejection velocity. Models and theory, however, have so far focused on the trajectory of ballistics after leaving the vent, neglecting the complex dynamics of their initial acceleration phase in the vent/conduit. Here, we use field-scale buried explosion experiments to study the ground-to-ground ballistic emplacement of particles through their entire acceleration-deceleration cycle. Twelve blasts were performed at the University at Buffalo Large Scale Experimental Facility with a range of scaled depths (burial depth divided by the cubic root of the energy of the explosive charge) and crater configurations. In all runs, ballistic analogs were placed on the ground surface at variable distance from the vertical projection of the buried charge, resulting in variable ejection angle. The chosen analogs are tennis and ping-pong balls filled with different materials, covering a limited range of sizes and densities. The analogs are tracked in multiple high-speed and high-definition videos, while Particle Image Velocimetry is used to detail ground motion in response to the buried blasts. In addition, after each blast the emplacement position of all analog ballistics was mapped with respect to the blast location. Preliminary results show the acceleration history of ballistics to be quite variable, from very short and relatively simple acceleration coupled with ground motion, to more complex, multi-stage accelerations possibly affected not only by the initial ground motion but also by variable coupling with the gas-particle mixture generated by the blasts. Further analysis of the experimental results is expected to provide new interpretative tools for ballistic deposits and better hazard assessment, with particular emphasis for the case of vent-opening eruptions driven by explosive gas expansion beneath loose debris.

Wound ballistics of the pig mandibular angle: a preliminary finite element analysis and experimental study.

PubMed

Chen, Yubin; Miao, Yingyun; Xu, Chuan; Zhang, Gang; Lei, Tao; Tan, Yinghui

2010-04-19

To study wound ballistics of the mandibular angle, a combined hexahedral-tetrahedral finite element (FE) model of the pig mandible was developed to simulate ballistic impact. An experimental study was carried out by measuring impact load parameters from 14 fresh pig mandibles that were shot at the mandibular angle by a standard 7.62 mm M43 bullet. FE analysis was executed through the LS-DYNA code under impact loads similar to those obtained from the experimental study. The resulting residual velocity, the transferred energy from the bullet to the mandible, and the surface area of the entrance wound had no statistical differences between the FE simulation and the experimental study. However, the mean surface area of the exit wounds in the experimental study was significantly larger than that in the simulation. According to the FE analysis, the stress concentrated zones were mainly located at the region of impact, condylar neck, coronoid process and mandibular body. The simulation results also indicated that trabecular bone had less stress concentration and a lower speed of stress propagation compared with cortical bone. The FE model is appropriate and conforms to the basic principles of wound ballistics. This modeling system will be helpful for further investigations of the biomechanical mechanisms of wound ballistics. Copyright 2009 Elsevier Ltd. All rights reserved.

Ballistic phonon transport in holey silicon.

PubMed

Lee, Jaeho; Lim, Jongwoo; Yang, Peidong

2015-05-13

When the size of semiconductors is smaller than the phonon mean free path, phonons can carry heat with no internal scattering. Ballistic phonon transport has received attention for both theoretical and practical aspects because Fourier's law of heat conduction breaks down and the heat dissipation in nanoscale transistors becomes unpredictable in the ballistic regime. While recent experiments demonstrate room-temperature evidence of ballistic phonon transport in various nanomaterials, the thermal conductivity data for silicon in the length scale of 10-100 nm is still not available due to experimental challenges. Here we show ballistic phonon transport prevails in the cross-plane direction of holey silicon from 35 to 200 nm. The thermal conductivity scales linearly with the length (thickness) even though the lateral dimension (neck) is as narrow as 20 nm. We assess the impact of long-wavelength phonons and predict a transition from ballistic to diffusive regime using scaling models. Our results support strong persistence of long-wavelength phonons in nanostructures and are useful for controlling phonon transport for thermoelectrics and potential phononic applications.

Room-temperature ballistic energy transport in molecules with repeating units

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rubtsova, Natalia I.; Nyby, Clara M.; Zhang, Hong

2015-06-07

In materials, energy can propagate by means of two limiting regimes: diffusive and ballistic. Ballistic energy transport can be fast and efficient and often occurs with a constant speed. Using two-dimensional infrared spectroscopy methods, we discovered ballistic energy transport via individual polyethylene chains with a remarkably high speed of 1440 m/s and the mean free path length of 14.6 Å in solution at room temperature. Whereas the transport via the chains occurs ballistically, the mechanism switches to diffusive with the effective transport speed of 130 m/s at the end-groups attached to the chains. A unifying model of the transport inmore » molecules is presented with clear time separation and additivity among the transport along oligomeric fragments, which occurs ballistically, and the transport within the disordered fragments, occurring diffusively. The results open new avenues for making novel elements for molecular electronics, including ultrafast energy transporters, controlled chemical reactors, and sub-wavelength quantum nanoseparators.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karp, A.

Belatedly, Western Nations are trying to staunch the flow of technology that has helped create a number of new ballistic missile forces in the Third World. Ballistic missiles already are being used in one Third World conflict. Since the end of February, Iran and Iraq have fired more than 100 short-range, inaccurate missiles at each other's cities, causing thousands of casualties. These events illustrate that ballistic missiles are becoming an ominous reality in the Third World. Indeed, 20 Third World countries, including Israel and Brazil, currently possess ballistic missiles or are striving to develop them. On one level, these missilesmore » - which are propelled by rockets into the upper atmosphere, travel in a ballistic trajectory, and are pulled by gravity to their targets - are for these nations a logical step in building up their military forces. While the missiles vary in range and accuracy, they can reach many targets in regional conflicts. Unlike manned aircraft, the do not require large, vulnerable bases. They are not as easily intercepted as slow bombers. And they are easier to develop because they are less sophisticated than modern cruise missiles such as the U.S. air-launched cruise missiles. In terms of global security, the most worrisome aspect of Third World ballistic missiles is their potential as nuclear weapons delivery systems.« less

A fully synthetic lung model for wound-ballistic experiments-First results.

PubMed

Bolliger, S A; Poschmann, S A; Thali, M J; Eggert, S

2017-06-01

Today, synthetic models have all but replaced animal and corpse models in examining damage to soft-tissues and skeletal structures by ballistic trauma. As, however, non-solid organs such as the lungs, have not been able to be replaced by a fully synthetic model we attempted to create such a model. 20% ordnance gelatine was frothed with a household mixer and cooled to stable foam. Several of these foam blocks were then stuck together with liquid gelatine and placed between 10% gelatine blocks. As controls, we embedded pig lungs in gelatine and compared the wound channels seen in computed tomography created upon shooting with 9mm Luger. The fully synthetic models displayed radiological and physical densities comparable to real lungs. The wound profile characteristics of the fully synthetic lung models were very similar to the semisynthetic swine-gelatine models regarding the permanent wound cavity. Furthermore, in both semi- and fully synthetic models we detected a ring surrounding the permanent wound channel, most likely representing the remnants of the temporary wound cavity. Our results indicate that this fully synthetic lung model is a viable substitute for ballistic experiments on lungs. We believe that further research on the temporary wound channel in lungs is possible with this model in order to provide more insight into the effect of ballistic trauma to the lungs not seen otherwise. Copyright © 2017 Elsevier B.V. All rights reserved.

A model for wind-extension of the Copernicus ejecta blanket

NASA Technical Reports Server (NTRS)

Rehfuss, D. E.; Michael, D.; Anselmo, J. C.; Kincheloe, N. K.

1977-01-01

The interaction between crater ejecta and the transient wind from impact-shock vaporization is discussed. Based partly on Shoemaker's (1962) ballistic model of the Copernicus ejecta and partly on Rehfuss' (1972) treatment of lunar winds, a simple model is developed which indicates that if Copernicus were formed by a basaltic meteorite impacting at 20 km/s, then 3% of the ejecta mass would be sent beyond the maximum range expected from purely ballistic trajectories. That 3% mass would, however, shift the position of the outer edge of the ejecta blanket more than 400% beyond the edge of the ballistic blanket. For planetary bodies lacking an intrinsic atmosphere, the present model indicates that this form of hyperballistic transport can be very significant for small (no more than about 1 kg) ejecta fragments.

Navy Columbia Class (Ohio Replacement) Ballistic Missile Submarine (SSBN[X]) Program: Background and Issues for Congress

DTIC Science & Technology

2016-10-25

program, a program to design and build a new class of 12 ballistic missile submarines (SSBNs) to replace the Navy’s current force of 14 Ohio-class SSBNs...billion in detailed design and nonrecurring engineering (DD/NRE) costs for the entire class, and $8.8 billion in construction costs for the ship... Design ................................................................................................................. 8 Program Cost

Computational and experimental models of the human torso for non-penetrating ballistic impact.

PubMed

Roberts, J C; Merkle, A C; Biermann, P J; Ward, E E; Carkhuff, B G; Cain, R P; O'Connor, J V

2007-01-01

Both computational finite element and experimental models of the human torso have been developed for ballistic impact testing. The human torso finite element model (HTFEM), including the thoracic skeletal structure and organs, was created in the finite element code LS-DYNA. The skeletal structure was assumed to be linear-elastic while all internal organs were modeled as viscoelastic. A physical human surrogate torso model (HSTM) was developed using biosimulant materials and the same anthropometry as the HTFEM. The HSTM response to impact was recorded with piezoresistive pressure sensors molded into the heart, liver and stomach and an accelerometer attached to the sternum. For experimentation, the HSTM was outfitted with National Institute of Justice (NIJ) Level I, IIa, II and IIIa soft armor vests. Twenty-six ballistic tests targeting the HSTM heart and liver were conducted with 22 caliber ammunition at a velocity of 329 m/s and 9 mm ammunition at velocities of 332, 358 and 430 m/s. The HSTM pressure response repeatability was found to vary by less than 10% for similar impact conditions. A comparison of the HSTM and HTFEM response showed similar pressure profiles and less than 35% peak pressure difference for organs near the ballistic impact point. Furthermore, the peak sternum accelerations of the HSTM and HTFEM varied by less than 10% for impacts over the sternum. These models provide comparative tools for determining the thoracic response to ballistic impact and could be used to evaluate soft body armor design and efficacy, determine thoracic injury mechanisms and assist with injury prevention.

IMM tracking of a theater ballistic missile during boost phase

NASA Astrophysics Data System (ADS)

Hutchins, Robert G.; San Jose, Anthony

1998-09-01

Since the SCUD launches in the Gulf War, theater ballistic missile (TBM) systems have become a growing concern for the US military. Detection, tracking and engagement during boost phase or shortly after booster cutoff are goals that grow in importance with the proliferation of weapons of mass destruction. This paper addresses the performance of tracking algorithms for TBMs during boost phase and across the transition to ballistic flight. Three families of tracking algorithms are examined: alpha-beta-gamma trackers, Kalman-based trackers, and the interactive multiple model (IMM) tracker. In addition, a variation on the IMM to include prior knowledge of a booster cutoff parameter is examined. Simulated data is used to compare algorithms. Also, the IMM tracker is run on an actual ballistic missile trajectory. Results indicate that IMM trackers show significant advantage in tracking through the model transition represented by booster cutoff.

Ballistic aggregation in systems of inelastic particles: Cluster growth, structure, and aging

NASA Astrophysics Data System (ADS)

Paul, Subhajit; Das, Subir K.

2017-07-01

We study far-from-equilibrium dynamics in models of freely cooling granular gas and ballistically aggregating compact clusters. For both the cases, from event-driven molecular dynamics simulations, we have presented detailed results on structure and dynamics in space dimensions d =1 and 2. Via appropriate analyses it has been confirmed that the ballistic aggregation mechanism applies in d =1 granular gases as well. Aging phenomena for this mechanism, in both the dimensions, have been studied via the two-time density autocorrelation function. This quantity is demonstrated to exhibit scaling property similar to that in the standard phase transition kinetics. The corresponding functional forms have been quantified and the outcomes have been discussed in connection with the structural properties. Our results on aging establish a more complete equivalence between the granular gas and the ballistic aggregation models in d =1 .

Ballistic Deficits for Ionization Chamber Pulses in Pulse Shaping Amplifiers

NASA Astrophysics Data System (ADS)

Kumar, G. Anil; Sharma, S. L.; Choudhury, R. K.

2007-04-01

In order to understand the dependence of the ballistic deficit on the shape of rising portion of the voltage pulse at the input of a pulse shaping amplifier, we have estimated the ballistic deficits for the pulses from a two-electrode parallel plate ionization chamber as well as for the pulses from a gridded parallel plate ionization chamber. These estimations have been made using numerical integration method when the pulses are processed through the CR-RCn (n=1-6) shaping network as well as when the pulses are processed through the complex shaping network of the ORTEC Model 472 spectroscopic amplifier. Further, we have made simulations to see the effect of ballistic deficit on the pulse-height spectra under different conditions. We have also carried out measurements of the ballistic deficits for the pulses from a two-electrode parallel plate ionization chamber as well as for the pulses from a gridded parallel plate ionization chamber when these pulses are processed through the ORTEC 572 linear amplifier having a simple CR-RC shaping network. The reasonable matching of the simulated ballistic deficits with the experimental ballistic deficits for the CR-RC shaping network clearly establishes the validity of the simulation technique

Precession feature extraction of ballistic missile warhead with high velocity

NASA Astrophysics Data System (ADS)

Sun, Huixia

2018-04-01

This paper establishes the precession model of ballistic missile warhead, and derives the formulas of micro-Doppler frequency induced by the target with precession. In order to obtain micro-Doppler feature of ballistic missile warhead with precession, micro-Doppler bandwidth estimation algorithm, which avoids velocity compensation, is presented based on high-resolution time-frequency transform. The results of computer simulations confirm the effectiveness of the proposed method even with low signal-to-noise ratio.

The effect of hydrogen content on ballistic transport behaviors in the Ni-Nb-Zr-H glassy alloys.

PubMed

Fukuhara, Mikio; Umemori, Yoshimasa

2012-01-01

The electronic transport behaviors of (Ni(0.39)Nb(0.25)Zr(0.35))(100-) (x)H(x) (0 ≤ x < 23.5) glassy alloys with subnanostructural icosahedral Zr(5)Nb(5)Ni(3) clusters have been studied as a function of hydrogen content. These alloys show semiconducting, electric current-induced voltage (Coulomb) oscillation and ballistic transport behaviors. Coulomb oscillation and ballistic transport occur at hydrogen contents between 6.7 and 13.5 at% and between 13.5 and 21.2 at%, respectively. These results suggest that the localization effect of hydrogen in the clusters plays an important role in various electron transport phenomena.

The Effect of Hydrogen Content on Ballistic Transport Behaviors in the Ni-Nb-Zr-H Glassy Alloys

PubMed Central

Fukuhara, Mikio; Umemori, Yoshimasa

2012-01-01

The electronic transport behaviors of (Ni0.39Nb0.25Zr0.35)100−xHx (0 ≤ x < 23.5) glassy alloys with subnanostructural icosahedral Zr5Nb5Ni3 clusters have been studied as a function of hydrogen content. These alloys show semiconducting, electric current-induced voltage (Coulomb) oscillation and ballistic transport behaviors. Coulomb oscillation and ballistic transport occur at hydrogen contents between 6.7 and 13.5 at% and between 13.5 and 21.2 at%, respectively. These results suggest that the localization effect of hydrogen in the clusters plays an important role in various electron transport phenomena. PMID:22312246

Effects of nanosized constriction on thermal transport properties of graphene

PubMed Central

2014-01-01

Thermal transport properties of graphene with nanosized constrictions are investigated using nonequilibrium molecular dynamics simulations. The results show that the nanosized constrictions have a significant influence on the thermal transport properties of graphene. The thermal resistance of the nanosized constrictions is on the order of 107 to 109 K/W at 150 K, which reduces the thermal conductivity by 7.7% to 90.4%. It is also found that the constriction resistance is inversely proportional to the width of the constriction and independent of the heat current. Moreover, we developed an analytical model for the ballistic thermal resistance of the nanosized constrictions in two-dimensional nanosystems. The theoretical prediction agrees well with the simulation results in this paper, which suggests that the thermal transport across the nanosized constrictions in two-dimensional nanosystems is ballistic in nature. PACS 65.80.CK; 61.48.Gh; 63.20.kp; 31.15.xv PMID:25232292

Ballistic Spin Field Effect Transistor Based on Silicon Nanowires

NASA Astrophysics Data System (ADS)

Osintsev, Dmitri; Sverdlov, Viktor; Stanojevic, Zlatan; Selberherr, Siegfried

2011-03-01

We investigate the properties of ballistic spin field-effect transistors build on silicon nanowires. An accurate description of the conduction band based on the k . p} model is necessary in thin and narrow silicon nanostructures. The subband effective mass and subband splitting dependence on the nanowire dimensions is analyzed and used in the transport calculations. The spin transistor is formed by sandwiching the nanowire between two ferromagnetic metallic contacts. Delta-function barriers at the interfaces between the contacts and the silicon channel are introduced. The major contribution to the electric field-dependent spin-orbit interaction in confined silicon systems is due to the interface-induced inversion asymmetry which is of the Dresselhaus type. We study the current and conductance through the system for the contacts being in parallel and anti-parallel configurations. Differences between the [100] and [110] orientated structures are investigated in details. This work is supported by the European Research Council through the grant #247056 MOSILSPIN.

USSR Report, Military Affairs Foreign Military Review No 6, June 1986

DTIC Science & Technology

1986-11-20

computers used for an objective accounting of the difference in current firing conditions from standard hold an important place in integrated fire...control systems of modern tanks of capitalist countries. Mechanical ballistic computers gave way in the early 1970’s to electronic computers , initially...made with analog components. Then digital ballistic computers were created, installed in particular in the Ml Abrams and Leopard-2 tanks. The basic

Design Guide for Aerodynamics Testing of Earth and Planetary Entry Vehicles in a Ballistic Range

NASA Technical Reports Server (NTRS)

Bogdanoff, David W.

2017-01-01

The purpose of this manual is to aid in the design of an aerodynamics test of an earth or planetary entry capsule in a ballistic range. In this manual, much use is made of the results and experience gained in 50 years of ballistic range aerodynamics testing at the NASA Ames Research Center, and in particular, that gained in the last 27 years, while the author was working at NASA Ames. The topics treated herein include: Data to be obtained; flight data needed to design test; Reynolds number and dynamic similarity of flight trajectory and ballistic range test; capabilities of various ballistic ranges; Calculations of swerves due to average and oscillating lift and of drag-induced velocity decreases; Model and sabot design; materials, weights and stresses; Sabot separation; Launches at angle of attack and slapping with paper to produce pitch/yaw oscillations.

Fiber-Level Modeling of Dynamic Strength of Kevlar (registered trademark) KM2 Ballistic Fabric

DTIC Science & Technology

2012-07-01

Ballistic-Performance Optimization of a Hybrid Carbon - Nanotube /E-glass Reinforced Poly-Vinyl-Ester-Epoxy-Matrix Com- posite Armor, J. Mater. Sci...2007, 42, p 5347–5359 4. M. Grujicic, W.C. Bell, L.L. Thompson, K.L. Koudela, and B.A. Cheeseman, Ballistic-Protection Performance of Carbon - Nanotube ...Armor via the Use of a Carbon - Nanotube Forest-Mat Strike Face, Mater. Des. Appl., 2008, 222, p 15–28 6. Y. Wang and X. Sun, Determining the Geometry

Ballistic-Failure Mechanisms in Gas Metal Arc Welds of MIL A46100 Armor-Grade Steel: A Computational Investigation

DTIC Science & Technology

2014-06-12

distribution is unlimited. Ballistic-Failure Mechanisms in Gas Metal Arc Welds of Mil A46100 Armor-Grade Steel : A Computational Investigation The views...Welds of Mil A46100 Armor-Grade Steel : A Computational Investigation Report Title In our recent work, a multi-physics computational model for the...introduction of the sixth module in the present work in recognition of the fact that in thick steel GMAW weldments, the overall ballistic performance

Ballistic intercept missions to Comet Encke

NASA Technical Reports Server (NTRS)

Mumma, M. (Compiler)

1975-01-01

The optimum ballistic intercept of a spacecraft with the comet Encke is determined. The following factors are considered in the analysis: energy requirements, encounter conditions, targeting error, comet activity, spacecraft engineering requirements and restraints, communications, and scientific return of the mission. A baseline model is formulated which includes the basic elements necessary to estimate the scientific return for the different missions considered. Tradeoffs which have major impact on the cost and/or scientific return of a ballistic mission to comet Encke are identified and discussed. Recommendations are included.

Ballistic-Failure Mechanisms in Gas Metal Arc Welds of Mil A46100 Armor-Grade Steel: A Computational Investigation

NASA Astrophysics Data System (ADS)

Grujicic, M.; Snipes, J. S.; Galgalikar, R.; Ramaswami, S.; Yavari, R.; Yen, C.-F.; Cheeseman, B. A.

2014-09-01

In our recent work, a multi-physics computational model for the conventional gas metal arc welding (GMAW) joining process was introduced. The model is of a modular type and comprises five modules, each designed to handle a specific aspect of the GMAW process, i.e.: (i) electro-dynamics of the welding-gun; (ii) radiation-/convection-controlled heat transfer from the electric-arc to the workpiece and mass transfer from the filler-metal consumable electrode to the weld; (iii) prediction of the temporal evolution and the spatial distribution of thermal and mechanical fields within the weld region during the GMAW joining process; (iv) the resulting temporal evolution and spatial distribution of the material microstructure throughout the weld region; and (v) spatial distribution of the as-welded material mechanical properties. In the present work, the GMAW process model has been upgraded with respect to its predictive capabilities regarding the spatial distribution of the mechanical properties controlling the ballistic-limit (i.e., penetration-resistance) of the weld. The model is upgraded through the introduction of the sixth module in the present work in recognition of the fact that in thick steel GMAW weldments, the overall ballistic performance of the armor may become controlled by the (often inferior) ballistic limits of its weld (fusion and heat-affected) zones. To demonstrate the utility of the upgraded GMAW process model, it is next applied to the case of butt-welding of a prototypical high-hardness armor-grade martensitic steel, MIL A46100. The model predictions concerning the spatial distribution of the material microstructure and ballistic-limit-controlling mechanical properties within the MIL A46100 butt-weld are found to be consistent with prior observations and general expectations.

Numerical Test of the Additivity Principle in Anomalous Transport

NASA Astrophysics Data System (ADS)

Tamaki, Shuji

2017-10-01

The additivity principle (AP) is one of the remarkable predictions that systematically generates all information on current fluctuations once the value of average current in the linear response regime is input. However, conditions to justify the AP are still ambiguous. We hence consider three tractable models, and discuss possible conditions. The models include the harmonic chain (HC), momentum exchange (ME) model, and momentum flip (MF) model, which respectively show ballistic, anomalous, and diffusive transport. We compare the heat current cumulants predicted by the AP with exact numerical data obtained for these models. The HC does not show the AP, whereas the MF model satisfies it, as expected, since the AP was originally proposed for diffusive systems. Surprisingly, the ME model also shows the AP. The ME model is known to show the anomalous transport similar to that shown in nonlinear systems such as the Fermi-Pasta-Ulam model. Our finding indicates that general nonlinear systems may satisfy the AP. Possible conditions for satisfying the AP are discussed.

Numerical modelling of physical processes in a ballistic laboratory setup with a tapered adapter and plastic piston used for obtaining high muzzle velocities

NASA Astrophysics Data System (ADS)

Bykov, N. V.

2014-12-01

Numerical modelling of a ballistic setup with a tapered adapter and plastic piston is considered. The processes in the firing chamber are described within the framework of quasi- one-dimensional gas dynamics and a geometrical law of propellant burn by means of Lagrangian mass coordinates. The deformable piston is considered to be an ideal liquid with specific equations of state. The numerical solution is obtained by means of a modified explicit von Neumann scheme. The calculation results given show that the ballistic setup with a tapered adapter and plastic piston produces increased shell muzzle velocities by a factor of more than 1.5-2.

Analysis of spacecraft entry into Mars atmosphere

NASA Astrophysics Data System (ADS)

Nakajima, Ken; Nagano, Koutarou

1991-07-01

The effects on a spacecraft body while entering the Martian atmosphere and the resulting design constraints are analyzed. The analyses are conducted using the Viking entry phase restriction conditions and a Mars atmosphere model. Results from analysis conducted by the Program to Optimize Simulated Trajectories (POST) are described. Results obtained from the analysis are as follows: (1) flight times depend greatly on lift-to-drag ratio and less on ballistic coefficients; (2) terminal landing speeds depend greatly on ballistic coefficients and less on lift-to-drag ratios; (3) the dependence of the flight path angles on ballistic coefficients is slightly larger than their dependence on lift-to-drag ratios; (4) as the ballistic coefficients become smaller and the lift-to-drag ratios become larger, the deceleration at high altitude becomes larger; (5) small ballistic coefficients and low lift-to-drag ratios are required to meet the constraints of Mach number at parachute deployment and deployment altitude; and (6) heating rates at stagnation points are dependent on ballistic coefficients. It is presumed that the aerodynamic characteristics will be 0.2 for the lift-to-drag ratio and 75 kg/sq m for the ballistic coefficient for the case of a Mars landing using capsules similar to those used in the Viking program.

Exploring the effects of overburden on the sublimation and transport of H2O on Iapetus

NASA Astrophysics Data System (ADS)

Rivera-Valentin, Edgard G.; Blackburn, David G.; Ulrich, Richard K.

2012-08-01

It has been shown through both measurements and simulations that there exists a measurable ice-free, porous, overburden overlaying water ice on Cassini Regio. Mass transfer through this porous media in a vacuum would occur in the Knudsen regime, which provides sublimation rates orders of magnitude smaller than Hertz-Langmuir sublimation. The availability of water ice for transport from this region is thus currently controlled by mass transfer through the dark material overburden. Thermal segregation suggests that Iapetus' polar regions have been brightened via ballistic transport of water and its subsequent cold trapping since exogenic deposition models predict dark high latitudes on the leading hemisphere. The limiting effect of the dark material on transport of water ice may thus greatly impact the current mass balance at the poles. The effects of the overburden on the global stability and transport of H2O is addressed in order to gain insight into its influence on the polar albedo distribution and current state of thermal segregation within the dark terrain. Results indicate that thermal segregation is currently an inactive or weak process within Cassini Regio, though it is an ongoing process at the inter-terrain regions. Modeling of polar accumulation suggests that even accounting for the current dark material cover within Cassini Regio there exists sufficient ballistically inbound water to overcome exogenic darkening mechanisms. Topographic effects on local albedo differences are also simulated to provide a more complete water stability study of Iapetus. Results suggest that topographically induced changes in heat flux may be sufficient to create the observed local albedo contrasts and also support ongoing dark exogenic deposition within Cassini Regio to explain the lack of bright slopes deep within the dark terrain.

Compact modeling of nanoscale triple-gate junctionless transistors covering drift-diffusion to quasi-ballistic carrier transport

NASA Astrophysics Data System (ADS)

Oproglidis, T. A.; Karatsori, T. A.; Barraud, S.; Ghibaudo, G.; Dimitriadis, C. A.

2018-04-01

In this work, we extend our analytical compact model for nanoscale junctionless triple-gate (JL TG) MOSFETs, capturing carrier transport from drift-diffusion to quasi-ballistic regime. This is based on a simple formulation of the low-field mobility extracted from experimental data using the Y-function method, taking into account the ballistic carrier motion and an increased carrier scattering in process-induced defects near the source/drain regions. The case of a Schottky junction in non-ideal ohmic contact at the drain side was also taken into account by modifying the threshold voltage and ideality factor of the JL transistor. The model is validated with experimental data for n-channel JL TG MOSFETs with channel length varying from 95 down to 25 nm. It can be easily implemented as a compact model for use in Spice circuit simulators.

Analysis of entry of additional energy to gunpowder in electrothermal chemical shot

NASA Astrophysics Data System (ADS)

Burkin, Viktor; Ishchenko, Alexandr; Kasimov, Vladimir; Samorokova, Nina; Sidorov, Aleksey

2017-11-01

In the article two series of ballistic experiments conducted according to the scheme of electrothermal chemical control of ballistic parameters of the shot at the Research Institute of Applied Mathematics and Mechanics of Tomsk State University (RIAMM TSU, Russia) are considered. The experimental part of the work is described. The analysis of the electro physical data of ballistic experiments is carried out. A methodical approach that allows to take into account the entry of an electric discharge plasma in a gunpowder in the mathematical model of internal ballistic processes in barrel systems is proposed and tested. Under the conditions of these experiments, the effects of various characteristics of the plasmatron on the nature of the energy entry are estimated.

Thermal transport in the Fermi-Pasta-Ulam model with long-range interactions

NASA Astrophysics Data System (ADS)

Bagchi, Debarshee

2017-03-01

We study the thermal transport properties of the one-dimensional Fermi-Pasta-Ulam model (β type) with long-range interactions. The strength of the long-range interaction decreases with the (shortest) distance between the lattice sites as distance-δ, where δ ≥0 . Two Langevin heat baths at unequal temperatures are connected to the ends of the one-dimensional lattice via short-range harmonic interactions that drive the system away from thermal equilibrium. In the nonequilibrium steady state the heat current, thermal conductivity, and temperature profiles are computed by solving the equations of motion numerically. It is found that the conductivity κ has an interesting nonmonotonic dependence with δ with a maximum at δ =2.0 for this model. Moreover, at δ =2.0 ,κ diverges almost linearly with system size N and the temperature profile has a negligible slope, as one expects in ballistic transport for an integrable system. We demonstrate that the nonmonotonic behavior of the conductivity and the nearly ballistic thermal transport at δ =2.0 obtained under nonequilibrium conditions can be explained consistently by studying the variation of largest Lyapunov exponent λmax with δ , and excess energy diffusion in the equilibrium microcanonical system.

A Klein-tunneling transistor with ballistic graphene

NASA Astrophysics Data System (ADS)

Wilmart, Quentin; Berrada, Salim; Torrin, David; Nguyen, V. Hung; Fève, Gwendal; Berroir, Jean-Marc; Dollfus, Philippe; Plaçais, Bernard

2014-06-01

Today, the availability of high mobility graphene up to room temperature makes ballistic transport in nanodevices achievable. In particular, p-n-p transistors in the ballistic regime give access to Klein tunneling physics and allow the realization of devices exploiting the optics-like behavior of Dirac Fermions (DFs) as in the Veselago lens or the Fabry-Pérot cavity. Here we propose a Klein tunneling transistor based on the geometrical optics of DFs. We consider the case of a prismatic active region delimited by a triangular gate, where total internal reflection may occur, which leads to the tunable suppression of transistor transmission. We calculate the transmission and the current by means of scattering theory and the finite bias properties using non-equilibrium Green's function (NEGF) simulation.

Injury representation against ballistic threats using three novel numerical models.

PubMed

Breeze, Johno; Fryer, R; Pope, D; Clasper, J

2017-06-01

Injury modelling of ballistic threats is a valuable tool for informing policy on personal protective equipment and other injury mitigation methods. Currently, the Ministry of Defence (MoD) and Centre for Protection of National Infrastructure (CPNI) are focusing on the development of three interlinking numerical models, each of a different fidelity, to answer specific questions on current threats. High-fidelity models simulate the physical events most realistically, and will be used in the future to test the medical effectiveness of personal armour systems. They are however generally computationally intensive, slow running and much of the experimental data to base their algorithms on do not yet exist. Medium fidelity models, such as the personnel vulnerability simulation (PVS), generally use algorithms based on physical or engineering estimations of interaction. This enables a reasonable representation of reality and greatly speeds up runtime allowing full assessments of the entire body area to be undertaken. Low-fidelity models such as the human injury predictor (HIP) tool generally use simplistic algorithms to make injury predictions. Individual scenarios can be run very quickly and hence enable statistical casualty assessments of large groups, where significant uncertainty concerning the threat and affected population exist. HIP is used to simulate the blast and penetrative fragmentation effects of a terrorist detonation of an improvised explosive device within crowds of people in metropolitan environments. This paper describes the collaboration between MoD and CPNI using an example of all three fidelities of injury model and to highlight future areas of research that are required. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Solid-propellant rocket motor internal ballistics performance variation analysis, phase 5

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Murph, J. E.

1980-01-01

The results of research aimed at improving the predictability of internal ballistics performance of solid-propellant rocket motors (SRM's) including thrust imbalance between two SRM's firing in parallel are presented. Static test data from the first six Space Shuttle SRM's is analyzed using a computer program previously developed for this purpose. The program permits intentional minor design biases affecting the imbalance between any two SMR's to be removed. Results for the last four of the six SRM's, with only the propellant bulk temperature as a non-random variable, are generally within limits predicted by theory. Extended studies of internal ballistic performance of single SRM's are presented based on an earlier developed mathematical model which includes an assessment of grain deformation. The erosive burning rate law used in the model is upgraded and made more general. Excellent results are obtained in predictions of the performances of five different SRM's of quite different sizes and configurations. These SRM's all employ PBAN type propellants with ammonium perchlorate oxidizer and 16 to 20% aluminum except one which uses carboxyl terminated butadiene binder. The only non-calculated parameters in the burning rate equations that are changed for the different SRM's are the zero crossflow velocity burning rate coefficients and exponents. The results, in general, confirm the importance of grain deformation. The improved internal ballistic model makes practical development of an effective computer program for application of an optimization technique to SRM design which is also demonstrated. The program uses a pattern search technique to minimize the difference between a desired thrust-time trace and one calculated based on the internal ballistic model.

Optimization of Gas Metal Arc Welding (GMAW) Process for Maximum Ballistic Limit in MIL A46100 Steel Welded All-Metal Armor

NASA Astrophysics Data System (ADS)

Grujicic, M.; Ramaswami, S.; Snipes, J. S.; Yavari, R.; Yen, C.-F.; Cheeseman, B. A.

2015-01-01

Our recently developed multi-physics computational model for the conventional gas metal arc welding (GMAW) joining process has been upgraded with respect to its predictive capabilities regarding the process optimization for the attainment of maximum ballistic limit within the weld. The original model consists of six modules, each dedicated to handling a specific aspect of the GMAW process, i.e., (a) electro-dynamics of the welding gun; (b) radiation-/convection-controlled heat transfer from the electric arc to the workpiece and mass transfer from the filler metal consumable electrode to the weld; (c) prediction of the temporal evolution and the spatial distribution of thermal and mechanical fields within the weld region during the GMAW joining process; (d) the resulting temporal evolution and spatial distribution of the material microstructure throughout the weld region; (e) spatial distribution of the as-welded material mechanical properties; and (f) spatial distribution of the material ballistic limit. In the present work, the model is upgraded through the introduction of the seventh module in recognition of the fact that identification of the optimum GMAW process parameters relative to the attainment of the maximum ballistic limit within the weld region entails the use of advanced optimization and statistical sensitivity analysis methods and tools. The upgraded GMAW process model is next applied to the case of butt welding of MIL A46100 (a prototypical high-hardness armor-grade martensitic steel) workpieces using filler metal electrodes made of the same material. The predictions of the upgraded GMAW process model pertaining to the spatial distribution of the material microstructure and ballistic limit-controlling mechanical properties within the MIL A46100 butt weld are found to be consistent with general expectations and prior observations.

Nonlinear transport theory in the metal with tunnel barrier

NASA Astrophysics Data System (ADS)

Zubov, E. E.

2018-02-01

Within the framework of the scattering matrix formalism, the nonlinear Kubo theory for electron transport in the metal with a tunnel barrier has been considered. A general expression for the mean electrical current was obtained. It significantly simplifies the calculation of nonlinear contributions to the conductivity of various hybrid structures. In the model of the tunnel Hamiltonian, all linear and nonlinear contributions to a mean electrical current are evaluated. The linear approximation agrees with results of other theories. For effective barrier transmission ?, the ballistic transport is realised with a value of the Landauer conductivity equal to ?.

Space-based infrared sensors of space target imaging effect analysis

NASA Astrophysics Data System (ADS)

Dai, Huayu; Zhang, Yasheng; Zhou, Haijun; Zhao, Shuang

2018-02-01

Target identification problem is one of the core problem of ballistic missile defense system, infrared imaging simulation is an important means of target detection and recognition. This paper first established the space-based infrared sensors ballistic target imaging model of point source on the planet's atmosphere; then from two aspects of space-based sensors camera parameters and target characteristics simulated atmosphere ballistic target of infrared imaging effect, analyzed the camera line of sight jitter, camera system noise and different imaging effects of wave on the target.

Computational Investigation of Effects of Grain Size on Ballistic Performance of Copper

NASA Astrophysics Data System (ADS)

He, Ge; Dou, Yangqing; Guo, Xiang; Liu, Yucheng

2018-01-01

Numerical simulations were conducted to compare ballistic performance and penetration mechanism of copper (Cu) with four representative grain sizes. Ballistic limit velocities for coarse-grained (CG) copper (grain size ≈ 90 µm), regular copper (grain size ≈ 30 µm), fine-grained (FG) copper (grain size ≈ 890 nm), and ultrafine-grained (UG) copper (grain size ≈ 200 nm) were determined for the first time through the simulations. It was found that the copper with reduced grain size would offer higher strength and better ductility, and therefore renders improved ballistic performance than the CG and regular copper. High speed impact and penetration behavior of the FG and UG copper was also compared with the CG coppers strengthened by nanotwinned (NT) regions. The comparison results showed the impact and penetration resistance of UG copper is comparable to the CG copper strengthened by NT regions with the minimum twin spacing. Therefore, besides the NT-strengthened copper, the single phase copper with nanoscale grain size could also be a strong candidate material for better ballistic protection. A computational modeling and simulation framework was proposed for this study, in which Johnson-Cook (JC) constitutive model is used to predict the plastic deformation of Cu; the JC damage model is to capture the penetration and fragmentation behavior of Cu; Bao-Wierzbicki (B-W) failure criterion defines the material's failure mechanisms; and temperature increase during this adiabatic penetration process is given by the Taylor-Quinney method.

Microwave Semiconductor Research - Materials, Devices and Circuits and Gallium Arsenide Ballistic Electron Transistors.

DTIC Science & Technology

1985-04-01

activation energies than previously possible. Electron traps and hole traps with energies less than 50 meV were observed for the first time in GaAs...developed in our laboratory to photoexcite electrons in a given energy range in the conduction band and then measure the relaxation of these carriers...limitations on the electron energy may be required. CURRENT AND FUTURE EFFORTS The possibility of ballistic electron transport in gallium arsenide has been

Expected scientific results on ballistic spacecraft missions to comet Encke during the 1980 apparition

NASA Technical Reports Server (NTRS)

Mumma, M. J.

1976-01-01

Summarized are three proposed ballistic spacecraft missions to intercept P/Encke during the 1980 apparition. A baseline physical activity model for P/Encke is established and the performances of the neutral mass spectrometer and of the imaging experiment on each intercept mission are assessed.

77 FR 6548 - Notice of Availability of Ballistic Survivability, Lethality and Vulnerability Analyses

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-08

..., Lethality and Vulnerability Analyses AGENCY: Department of the Army, DoD. ACTION: Notice of availability...) is a leader in ballistic survivability, lethality and vulnerability (SLV) analyses. ARL/SLAD conducts SLV analyses, using the MUVES-S2 vulnerability model, to quantify system, subsystem and/or component...

Dynamic CFD Simulations of the Supersonic Inflatable Aerodynamic Decelerator (SIAD) Ballistic Range Tests

NASA Technical Reports Server (NTRS)

Brock, Joseph M; Stern, Eric

2016-01-01

Dynamic CFD simulations of the SIAD ballistic test model were performed using US3D flow solver. Motivation for performing these simulations is for the purpose of validation and verification of the US3D flow solver as a viable computational tool for predicting dynamic coefficients.

Estimation of ballistic block landing energy during 2014 Mount Ontake eruption

NASA Astrophysics Data System (ADS)

Tsunematsu, Kae; Ishimine, Yasuhiro; Kaneko, Takayuki; Yoshimoto, Mitsuhiro; Fujii, Toshitsugu; Yamaoka, Koshun

2016-05-01

The 2014 Mount Ontake eruption started just before noon on September 27, 2014. It killed 58 people, and five are still missing (as of January 1, 2016). The casualties were mainly caused by the impact of ballistic blocks around the summit area. It is necessary to know the magnitude of the block velocity and energy to construct a hazard map of ballistic projectiles and design effective shelters and mountain huts. The ejection velocities of the ballistic projectiles were estimated by comparing the observed distribution of the ballistic impact craters on the ground with simulated distributions of landing positions under various sets of conditions. A three-dimensional numerical multiparticle ballistic model adapted to account for topographic effect was used to estimate the ejection angles. From these simulations, we have obtained an ejection angle of γ = 20° from vertical to horizontal and α = 20° from north to east. With these ejection angle conditions, the ejection speed was estimated to be between 145 and 185 m/s for a previously obtained range of drag coefficients of 0.62-1.01. The order of magnitude of the mean landing energy obtained using our numerical simulation was 104 J.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Yang; Liu, Zhiqiang, E-mail: lzq@semi.ac.cn, E-mail: spring@semi.ac.cn; Yi, Xiaoyan, E-mail: lzq@semi.ac.cn, E-mail: spring@semi.ac.cn

To evaluate electron leakage in InGaN/GaN multiple quantum well (MQW) light emitting diodes (LEDs), analytic models of ballistic and quasi-ballistic transport are developed. With this model, the impact of critical variables effecting electron leakage, including the electron blocking layer (EBL), structure of multiple quantum wells (MQWs), polarization field, and temperature are explored. The simulated results based on this model shed light on previously reported experimental observations and provide basic criteria for suppressing electron leakage, advancing the design of InGaN/GaN LEDs.

Developmental framework to validate future designs of ballistic neck protection.

PubMed

Breeze, J; Midwinter, M J; Pope, D; Porter, K; Hepper, A E; Clasper, J

2013-01-01

The number of neck injuries has increased during the war in Afghanistan, and they have become an appreciable source of mortality and long-term morbidity for UK servicemen. A three-dimensional numerical model of the neck is necessary to allow simulation of penetrating injury from explosive fragments so that the design of body armour can be optimal, and a framework is required to validate and describe the individual components of this program. An interdisciplinary consensus group consisting of military maxillofacial surgeons, and biomedical, physical, and material scientists was convened to generate the components of the framework, and as a result it incorporates the following components: analysis of deaths and long-term morbidity, assessment of critical cervical structures for incorporation into the model, characterisation of explosive fragments, evaluation of the material of which the body armour is made, and mapping of the entry sites of fragments. The resulting numerical model will simulate the wound tract produced by fragments of differing masses and velocities, and illustrate the effects of temporary cavities on cervical neurovascular structures. Using this framework, a new shirt to be worn under body armour that incorporates ballistic cervical protection has been developed for use in Afghanistan. New designs of the collar validated by human factors and assessment of coverage are currently being incorporated into early versions of the numerical model. The aim of this paper is to describe this developmental framework and provide an update on the current progress of its individual components. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Assessing behind armor blunt trauma (BABT) under NIJ standard-0101.04 conditions using human torso models.

PubMed

Merkle, Andrew C; Ward, Emily E; O'Connor, James V; Roberts, Jack C

2008-06-01

Although soft armor vests serve to prevent penetrating wounds and dissipate impact energy, the potential of nonpenetrating injury to the thorax, termed behind armor blunt trauma, does exist. Currently, the ballistic resistance of personal body armor is determined by impacting a soft armor vest over a clay backing and measuring the resulting clay deformation as specified in National Institute of Justice (NIJ) Standard-0101.04. This research effort evaluated the efficacy of a physical Human Surrogate Torso Model (HSTM) as a device for determining thoracic response when exposed to impact conditions specified in the NIJ Standard. The HSTM was subjected to a series of ballistic impacts over the sternum and stomach. The pressure waves propagating through the torso were measured with sensors installed in the organs. A previously developed Human Torso Finite Element Model (HTFEM) was used to analyze the amount of tissue displacement during impact and compared with the amount of clay deformation predicted by a validated finite element model. All experiments and simulations were conducted at NIJ Standard test conditions. When normalized by the response at the lowest threat level (Level I), the clay deformations for the higher levels are relatively constant and range from 2.3 to 2.7 times that of the base threat level. However, the pressures in the HSTM increase with each test level and range from three to seven times greater than Level I depending on the organ. The results demonstrate the abilities of the HSTM to discriminate between threat levels, impact conditions, and impact locations. The HTFEM and HSTM are capable of realizing pressure and displacement differences because of the level of protection, surrounding tissue, and proximity to the impact point. The results of this research provide insight into the transfer of energy and pressure wave propagation during ballistic impacts using a physical surrogate and computational model of the human torso.

3D topography measurements on correlation cells—a new approach to forensic ballistics identifications

NASA Astrophysics Data System (ADS)

Song, John; Chu, Wei; Tong, Mingsi; Soons, Johannes

2014-06-01

Based on three-dimensional (3D) topography measurements on correlation cells, the National Institute of Standards and Technology (NIST) has developed the ‘NIST Ballistics Identification System (NBIS)’ aimed at accurate ballistics identifications and fast ballistics evidence searches. The 3D topographies are divided into arrays of correlation cells to identify ‘valid correlation areas’ and eliminate ‘invalid correlation areas’ from the matching and identification procedure. A ‘congruent matching cells’ (CMC)’ method using three types of identification parameters of the paired correlation cells (cross correlation function maximum CCFmax, spatial registration position in x-y and registration angle θ) is used for high accuracy ballistics identifications. ‘Synchronous processing’ is proposed for correlating multiple cell pairs at the same time to increase the correlation speed. The proposed NBIS can be used for correlations of both geometrical topographies and optical intensity images. All the correlation parameters and algorithms are in the public domain and subject to open tests. An error rate reporting procedure has been developed that can greatly add to the scientific support for the firearm and toolmark identification specialty, and give confidence to the trier of fact in court proceedings. The NBIS is engineered to employ transparent identification parameters and criteria, statistical models and correlation algorithms. In this way, interoperability between different ballistics identification systems can be more easily achieved. This interoperability will make the NBIS suitable for ballistics identifications and evidence searches with large national databases, such as the National Integrated Ballistic Information Network in the United States.

Contemporary body armor: technical data, injuries, and limits.

PubMed

Prat, N; Rongieras, F; Sarron, J-C; Miras, A; Voiglio, E

2012-04-01

The introduction of firearms in the fifteenth century led to the continuous development of bulletproof personal protection. Due to recent industrial progress and the emergence of a new generation of ballistic fibers in the 1960s, the ability of individual ballistic protections to stop projectiles greatly increased. While protective equipment is able to stop increasingly powerful missiles, deformation during the impact can cause potentially lethal nonpenetrating injuries that are grouped under the generic term of behind armor blunt trauma, and the scope and consequences of these are still unclear. This review first summarizes current technical data for modern bulletproof vests, the materials used in them, and the stopping mechanisms they employ. Then it describes recent research into the specific ballistic injury patterns of soldiers wearing body armor, focusing on behind-armor blunt trauma.

Innovative 3D Textile Structures for Soft Body Armor Protection: The EPIDARM Project

NASA Astrophysics Data System (ADS)

Maillet, Jérôme; Lefebvre, Marie; Boussu, François; Pirlot, Marc

There is a real need for battlefield soldiers to be protected from ­ballistic and CBRNE threats and also to be in permanent contact and localization with the logistic support of the commander. Ballistic, CBRNE and tactical jackets are currently three different components, developed separately and worn on top of each other. One of the EPIDARM project's targets is to propose a personal protection demonstration for the optimal system configuration in order to reduce the cost and weight while improving protection. The systems approach used for the EPIDARM program considers the protective system inside its environment (threat, the wearer - generic soldier, task and climates). The latest emergent technologies in ballistic and CBRN protection, ergonomic effectiveness and financial cost are considered and help to select final solutions.

Ballistics Modeling for Non-Axisymmetric Hypervelocity Smart Bullets

DTIC Science & Technology

2014-06-03

can in principle come from experiments or computational fluid dynamics ( CFD ) calculations. CFD calculations are carried out for a standard bullet...come from experiments or com- putational fluid dynamics ( CFD ) calculations. CFD calculations are carried out for a standard bullet (0.308” 168 grain...11 2. Spin and Pitch Damping 11 3. Magnus Moment 12 IV. CFD Simulations and Ballistic Trajectories 12 A. CFD Modeling of a Standard Bullet 12 B

Ignition of a granular propellant bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wildegger-Gaissmaier, A.E.; Johnston, I.R.

1996-08-01

An experimental and theoretical study is reported on the ignition process of a low vulnerability ammunition (LOVA) propellant bed in a 127-mm (5-in) bore gun charge. The theoretical investigation was with a two-phase flow interior ballistics code and the model predictions showed the marked influence the igniter system can have on pressure wave development, flame spreading, and the overall interior ballistics performance. A number of different igniter systems were investigated in an empty and propellant-filled gun simulator. Pressure, flame spreading, and high-speed film records were used to analyze the ignition/combustion event. The model predictions for flame spreading were confirmed qualitativelymore » by the experimental data. Full-scale instrumented gun firings were conducted with the optimized igniter design. Pressure waves were not detected in the charge during the firings. Model predictions on overall interior ballistics performance agreed well with the firing data.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Norris, R.S.; Arkin, W.M.

The US. nuclear stockpile is at its lowest level since late 1958 or early 1959. In the past year, many weapons were returned to central military storage depots in the United States and funneled to the Energy Department's Pantex facility for final disassembly and disposal. This article presents a table showing the author's current estimate of the composition of the current operational stockpile, which contains some 10,500 warheads. Also categorized are warheads in [open quotes]inactive reserve[close quotes] and warheads awaiting eventual disassembly. The warheads are generally grouped as bombs, submarine-launched ballistic missiles, intercontinental ballistic missiles, air-launched cruise missiles, and sea-launchedmore » cruise missiles. Initial production dates and yield are listed for the warheads.« less

Modelling of dispersal and deposition of impact glass spherules from the Cretaceous-Tertiary boundary deposit

NASA Technical Reports Server (NTRS)

Espindola, J. M.; Carey, S.; Sigurdsson, H.

1993-01-01

The dispersal of glass spherules or tektites from a bolide impact with the Earth is modelled as ballistic trajectories in standard atmosphere. Ballistic dispersal of Cretaceous-Tertiary boundary impact glass spherules found in Haiti and Mimbral, Mexico requires a fireball radius in excess of 50 km but less than 100 km to account for the observed distribution. Glass spherules from 1 and up to 8 mm in diameter have been found at the KT boundary at Beloc in Haiti, at Mimbral, Mexico, and at DSDP Sites 536 and 540 in the Gulf of Mexico corresponding to paleodistances of 600 to 1000 km from the Chicxulub crater. In Haiti the basal and major glass-bearing unit at the KT boundary is attributed to fallout on basis of sedimentologic features. When compared with theoretical and observed dispersal of volcanic ejecta, the grain size versus distance relationship of the KT boundary tektite fallout is extreme, and rules out a volcanic fallout origin. At a comparable distance from source, the KT impact glass spherules are more than an order of mangitude coarser than ejecta of the largest known volcanic events. We model the dispersal of KT boundary impact glass spherules as ballistic ejecta from a fireball generated by the impact of a 10 km diameter bolide. Mass of ejecta in the fireball is taken as twice the bolide mass. Melt droplets are accelerated by gas flow in the fireball cloud, and leave the fireball on ballistic trajectories within the atmosphere, subject to drag, depending on angle of ejection and altitude. The model for ballistic dispersal is based on equations of motion, drag and ablation for silicate spheres in standard atmosphere.

A Materials Approach in the Development of Multi-Threat Warfighter Head Protection

DTIC Science & Technology

2008-12-01

TUSJp TYSlp ’--- --"IO,,5083-="" H13 .’ (AI) ’AZ31B-H2’",(~",),,-- __ Figure 6. Specific Strength of Mg vs. Al Alloy Armor Plate of current interest because...perfonnance in metal alloys, and higher stiffness typically contributes to enhanced energy absorption upon ballistic impact ; therefore, one would predict...Helmets, and ballistic helmets in particular. have not been dominated by stiffness requirements but rather other properties (e.g., crash, impact

Ballistic-electron-emission spectroscopy of Al{sub x}Ga{sub 1{minus}x}As/GaAs heterostructures: Conduction-band offsets, transport mechanisms, and band-structure effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

OShea, J.J.; Brazel, E.G.; Rubin, M.E.

1997-07-01

We report an extensive investigation of semiconductor band-structure effects in single-barrier Al{sub x}Ga{sub 1{minus}x}As/GaAs heterostructures using ballistic-electron-emission spectroscopy (BEES). The transport mechanisms in these single-barrier structures were studied systematically as a function of temperature and Al composition over the full compositional range (0{le}x{le}1). The initial ({Gamma}) BEES thresholds for Al{sub x}Ga{sub 1{minus}x}As single barriers with 0{le}x{le}0.42 were extracted using a model which includes the complete transmission probability of the metal-semiconductor interface and the semiconductor heterostructure. Band offsets measured by BEES are in good agreement with previous measurements by other techniques which demonstrates the accuracy of this technique. BEES measurements atmore » 77 K give the same band-offset values as at room temperature. When a reverse bias is applied to the heterostructures, the BEES thresholds shift to lower voltages in good agreement with the expected bias-induced band-bending. In the indirect band-gap regime ({ital x}{gt}0.45), spectra show a weak ballistic-electron-emission microscopy current contribution due to intervalley scattering through Al{sub x}Ga{sub 1{minus}x}As {ital X} valley states. Low-temperature spectra show a marked reduction in this intervalley current component, indicating that intervalley phonon scattering at the GaAs/Al{sub x}Ga{sub 1{minus}x}As interface produces a significant fraction of this{ital X} valley current. A comparison of the BEES thresholds with the expected composition dependence of the Al{sub x}Ga{sub 1{minus}x}As {Gamma}, {ital L}, and {ital X} points yields good agreement over the entire composition range. {copyright} {ital 1997} {ital The American Physical Society}« less

Multi-hierarchical movements in self-avoiding walks

NASA Astrophysics Data System (ADS)

Sakiyama, Tomoko; Gunji, Yukio-Pegio

2017-07-01

A self-avoiding walk (SAW) is a series of moves on a lattice that visit the same place only once. Several studies reported that repellent reactions of foragers to previously visited sites induced power-law tailed SAWs in animals. In this paper, we show that modelling the agent's multi-avoidance reactions to its trails enables it to show ballistic movements which result in heavy-tailed movements. There is no literature showing emergent ballistic movements in SAWs. While following SAWs, the agent in my model changed its reactions to marked patches (visited sites) by considering global trail patterns based on local trail patterns when the agent was surrounded by previously visited sites. As a result, we succeeded in producing ballistic walks by the agents which exhibited emergent power-law tailed movements.

Targeting Ballistic Lunar Capture Trajectories Using Periodic Orbits in the Sun-Earth CRTBP

NASA Technical Reports Server (NTRS)

Cooley, D.S.; Griesemer, Paul Ricord; Ocampo, Cesar

2009-01-01

A particular periodic orbit in the Earth-Sun circular restricted three body problem is shown to have the characteristics needed for a ballistic lunar capture transfer. An injection from a circular parking orbit into the periodic orbit serves as an initial guess for a targeting algorithm. By targeting appropriate parameters incrementally in increasingly complicated force models and using precise derivatives calculated from the state transition matrix, a reliable algorithm is produced. Ballistic lunar capture trajectories in restricted four body systems are shown to be able to be produced in a systematic way.

Coherent Charge Transport in Ballistic InSb Nanowire Josephson Junctions

PubMed Central

Li, S.; Kang, N.; Fan, D. X.; Wang, L. B.; Huang, Y. Q.; Caroff, P.; Xu, H. Q.

2016-01-01

Hybrid InSb nanowire-superconductor devices are promising for investigating Majorana modes and topological quantum computation in solid-state devices. An experimental realisation of ballistic, phase-coherent superconductor-nanowire hybrid devices is a necessary step towards engineering topological superconducting electronics. Here, we report on a low-temperature transport study of Josephson junction devices fabricated from InSb nanowires grown by molecular-beam epitaxy and provide a clear evidence for phase-coherent, ballistic charge transport through the nanowires in the junctions. We demonstrate that our devices show gate-tunable proximity-induced supercurrent and clear signatures of multiple Andreev reflections in the differential conductance, indicating phase-coherent transport within the junctions. We also observe periodic modulations of the critical current that can be associated with the Fabry-Pérot interference in the nanowires in the ballistic transport regime. Our work shows that the InSb nanowires grown by molecular-beam epitaxy are of excellent material quality and hybrid superconducting devices made from these nanowires are highly desirable for investigation of the novel physics in topological states of matter and for applications in topological quantum electronics. PMID:27102689

Influence of Scattering on Ballistic Nanotransistor Design

NASA Technical Reports Server (NTRS)

Anantram, M. P.; Svizhenko, Alexei; Biegel, Bryan, A. (Technical Monitor)

2002-01-01

Importance of this work: (1) This is the first work to model electron-phonon scattering within a quantum mechanical approach to nanotransistors. The simulations use the non equilibrium Green's function method. (2) A simple equation which captures the importance of scattering as a function of the spatial location from source to drain is presented. This equation helps interpret the numerical simulations. (3) We show that the resistance per unit length in the source side is much larger than in the drain side. Thus making scattering in the source side of the device much more important than scattering in the drain side. Numerical estimates of ballisticity for 10nm channel length devices in the presence of of electron-phonon scattering are given. Based on these calculations, we propose that to achieve a larger on-current in nanotransistors, it is crucial to keep the highly doped source extension region extremely small, even if this is at the cost of making the highly doped drain extension region longer.

Advanced Spectroscopic and Thermal Imaging Instrumentation for Shock Tube and Ballistic Range Facilities

NASA Technical Reports Server (NTRS)

Grinstead, Jay H.; Wilder, Michael C.; Reda, Daniel C.; Cruden, Brett A.; Bogdanoff, David W.

2010-01-01

The Electric Arc Shock Tube (EAST) facility and Hypervelocity Free Flight Aerodynamic Facility (HFFAF, an aeroballistic range) at NASA Ames support basic research in aerothermodynamic phenomena of atmospheric entry, specifically shock layer radiation spectroscopy, convective and radiative heat transfer, and transition to turbulence. Innovative optical instrumentation has been developed and implemented to meet the challenges posed from obtaining such data in these impulse facilities. Spatially and spectrally resolved measurements of absolute radiance of a travelling shock wave in EAST are acquired using multiplexed, time-gated imaging spectrographs. Nearly complete spectral coverage from the vacuum ultraviolet to the near infrared is possible in a single experiment. Time-gated thermal imaging of ballistic range models in flight enables quantitative, global measurements of surface temperature. These images can be interpreted to determine convective heat transfer rates and reveal transition to turbulence due to isolated and distributed surface roughness at hypersonic velocities. The focus of this paper is a detailed description of the optical instrumentation currently in use in the EAST and HFFAF.

Statement of Rear Admiral Nevin P. Carr, Jr., United States Navy Chief of Naval Research before the Terrorism, Unconventional Threats and Capabilities Subcommittee of the House Armed Services Committee on The Fiscal year 2011 Budget Request

DTIC Science & Technology

2010-03-23

foundation of our S&T portfolio by developing a broad base of scientific knowledge from which INP, FNC, and quick reaction efforts are generated...optimally tailoring experiences, in real-time, to current cognitive and physiological states of the learner. A unique human systems design approach is...efforts include modeling human responses to blast, ballistic, and blunt trauma, as well as modeling physical and cognitive effects of blast exposure and

Nano-Transistor Modeling: Two Dimensional Green's Function Method

NASA Technical Reports Server (NTRS)

Svizhenko, Alexei; Anantram, M. P.; Govindan, T. R.; Biegel, Bryan

2001-01-01

Two quantum mechanical effects that impact the operation of nanoscale transistors are inversion layer energy quantization and ballistic transport. While the qualitative effects of these features are reasonably understood, a comprehensive study of device physics in two dimensions is lacking. Our work addresses this shortcoming and provides: (a) a framework to quantitatively explore device physics issues such as the source-drain and gate leakage currents, DIBL (Drain Induced Barrier Lowering), and threshold voltage shift due to quantization, and b) a means of benchmarking quantum corrections to semiclassical models (such as density-gradient and quantum-corrected MEDICI).

A musculoskeletal model of the elbow joint complex

NASA Technical Reports Server (NTRS)

Gonzalez, Roger V.; Barr, Ronald E.; Abraham, Lawrence D.

1993-01-01

This paper describes a musculoskeletal model that represents human elbow flexion-extension and forearm pronation-supination. Musculotendon parameters and the skeletal geometry were determined for the musculoskeletal model in the analysis of ballistic elbow joint complex movements. The key objective was to develop a computational model, guided by optimal control, to investigate the relationship among patterns of muscle excitation, individual muscle forces, and movement kinematics. The model was verified using experimental kinematic, torque, and electromyographic data from volunteer subjects performing both isometric and ballistic elbow joint complex movements. In general, the model predicted kinematic and muscle excitation patterns similar to what was experimentally measured.

Writing with ring currents: selectively hydrogenated polycyclic aromatics as finite models of graphene and graphane

PubMed Central

Fowler, Patrick W.; Gibson, Christopher M.; Bean, David E.

2014-01-01

Alternating partial hydrogenation of the interior region of a polycyclic aromatic hydrocarbon gives a finite model system representing systems on the pathway from graphene to the graphane modification of the graphene sheet. Calculations at the DFT and coupled Hartree–Fock levels confirm that sp2 cycles of bare carbon centres isolated by selective hydrogenation retain the essentially planar geometry and electron delocalization of the annulene that they mimic. Delocalization is diagnosed by the presence of ring currents, as detected by ipsocentric calculation and visualization of the current density induced in the π system by a perpendicular external magnetic field. These induced ‘ring’ currents have essentially the same sense, strength and orbital origin as in the free hydrocarbon. Subjected to the important experimental proviso of the need for atomic-scale control of hydrogenation, this finding predicts the possibility of writing single, multiple and concentric diatropic and/or paratropic ring currents on the graphene/graphane sheet. The implication is that pathways for free flow of ballistic current can be modelled in the same way. PMID:24611026

Hybrid carbon-glass fiber/toughened epoxy thick composites subject to drop-weight and ballistic impacts

NASA Astrophysics Data System (ADS)

Sevkat, Ercan

The goals of this study are to investigate the low velocity and ballistic impact response of thick-section hybrid fiber composites at room temperature. Plain-woven S2-Glass and IM7 Graphite fabrics are chosen as fiber materials reinforcing the SC-79 epoxy. Four different types of composites consisting of alternating layers of glass and graphite woven fabric sheets are considered. Tensile tests are conducted using 98 KN (22 kip) MTS testing machine equipped with environmental chamber. Low-velocity impact tests are conducted using an Instron-Dynatup 8250 impact test machine equipped with an environmental chamber. Ballistic impact tests are performed using helium pressured high-speed gas-gun. Tensile tests results were used to define the material behavior of the hybrid and non-hybrid composites in Finite Element modeling. The low velocity and ballistic impact tests showed that hybrid composites performance was somewhere between non-hybrid woven composites. Using woven glass fabrics as outer skin improved the impact performance of woven graphite composite. However hybrid composites are prone to delamination especially between dissimilar layers. The ballistic limit velocity V50 hybrid composites were higher that of woven graphite composite and lower than that of woven glass composite. Both destructive cross-sectional micrographs and nondestructive ultrasonic techniques are used to evaluate the damage created by impact. The Finite Element code LS-DYNA is chosen to perform numerical simulations of low velocity and ballistic impact on thick-section hybrid composites. The damage progression in these composites shows anisotropic nonlinearity. The material model to describe this behavior is not available in LS-DYNA material library. Initially, linear orthotropic material with damage (Chan-Chan Model) is employed to simulate some of the experimental results. Then, user-defined material subroutine is incorporated into LS-DYNA to simulate the nonlinear behavior. The experimentally obtained force-time histories, strain-time histories and damage patterns of impacted composites are compared with Finite element results. The results indicate that LS-DYNA could simulate the impact responses with sufficient accuracy once proper material models and boundary conditions are defined.

Modeling Ballistic Current Flow in Carbon Nanotube Wires

NASA Technical Reports Server (NTRS)

Anantram, M. P.; Biegel, Bryan (Technical Monitor)

2001-01-01

Experiments have shown carbon nanotubes (CNT) to be almost perfect conductors at small applied biases. The features of the CNT band structure, large velocity of the crossing subbands and the small number of modes that an electron close to the band center / Fermi energy can scatter into, are the reasons for the near perfect small bias conductance. We show that the CNT band structure does not help at large applied biases - electrons injected into the non crossing subbands can either be Bragg reflected or undergo Zener-type tunneling. This limits the current carrying capacity of CNT. We point out that the current carrying capacity of semiconductor quantum wires in the ballistic limit is different, owing to its band structure. The second aspect addressed is the relationship of nanotube chirality in determining the physics of metal-nanotube coupling. We show that a metallic-zigzag nanotube couples better than an armchair nanotube to a metal contact. This arises because in the case of armchair nanotubes, while the pi band couples well, the pi* band does not couple well to the metal. In the case of zigzag nanotube both crossing modes couple reasonably well to the metal. Many factors such as the role of curvature, strain and defects will play a role in determining the suitability of nanotubes as nanowires. From the limited view point of metal-nanotube coupling, we feel that metallic-zigzag nanotubes are preferable to armchair nanotubes.

Hazard map for volcanic ballistic impacts at El Chichón volcano (Mexico)

NASA Astrophysics Data System (ADS)

Alatorre-Ibarguengoitia, Miguel; Ramos-Hernández, Silvia; Jiménez-Aguilar, Julio

2014-05-01

The 1982 eruption of El Chichón Volcano in southeastern Mexico had a strong social and environmental impact. The eruption resulted in the worst volcanic disaster in the recorded history of Mexico, causing about 2,000 casualties, displacing thousands, and producing severe economic losses. Even when some villages were relocated after the 1982 eruption, many people still live and work in the vicinities of the volcano and may be affected in the case of a new eruption. The hazard map of El Chichón volcano (Macías et al., 2008) comprises pyroclastic flows, pyroclastic surges, lahars and ash fall but not ballistic projectiles, which represent an important threat to people, infrastructure and vegetation in the case of an eruption. In fact, the fatalities reported in the first stage of the 1982 eruption were caused by roof collapse induced by ashfall and lithic ballistic projectiles. In this study, a general methodology to delimit the hazard zones for volcanic ballistic projectiles during volcanic eruptions is applied to El Chichón volcano. Different scenarios are defined based on the past activity of the volcano and parameterized by considering the maximum kinetic energy associated with ballistic projectiles ejected during previous eruptions. A ballistic model is used to reconstruct the "launching" kinetic energy of the projectiles observed in the field. The maximum ranges expected for the ballistics in the different explosive scenarios defined for El Chichón volcano are presented in a ballistic hazard map which complements the published hazard map. These maps assist the responsible authorities to plan the definition and mitigation of restricted areas during volcanic crises.

Viscoelastic shock wave in ballistic gelatin behind soft body armor.

PubMed

Liu, Li; Fan, Yurun; Li, Wei

2014-06-01

Ballistic gelatins are widely used as a surrogate of biological tissue in blunt trauma tests. Non-penetration impact tests of handgun bullets on the 10wt% ballistic gelatin block behind soft armor were carried out in which a high-speed camera recorded the crater׳s movement and pressure sensors imbedded in the gelatin block recorded the pressure waves at different locations. The observed shock wave attenuation indicates the necessity of considering the gelatin׳s viscoelasticity. A three-element viscoelastic constitutive model was adopted, in which the relevant parameters were obtained via fitting the damping free oscillations at the beginning of the creep-mode of rheological measurement, and by examining the data of published split Hopkinson pressure bar (SHPB) experiments. The viscoelastic model is determined by a retardation time of 5.5×10(-5)s for high oscillation frequencies and a stress relaxation time of 2.0-4.5×10(-7)s for shock wave attenuation. Using the characteristic-line method and the spherical wave assumption, the propagation of impact pressure wave front and the subsequent unloading profile can be simulated using the experimental velocity boundary condition. The established viscoelastic model considerably improves the prediction of shock wave attenuation in the ballistic gelatin. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of a skull/brain model for military wound ballistics studies.

PubMed

Carr, Debra; Lindstrom, Anne-Christine; Jareborg, Andreas; Champion, Stephen; Waddell, Neil; Miller, David; Teagle, Michael; Horsfall, Ian; Kieser, Jules

2015-05-01

Reports on penetrating ballistic head injuries in the literature are dominated by case studies of suicides; the penetrating ammunition usually being .22 rimfire or shotgun. The dominating cause of injuries in modern warfare is fragmentation and hence, this is the primary threat that military helmets protect the brain from. When helmets are perforated, this is usually by bullets. In combat, 20% of penetrating injuries occur to the head and its wounding accounts for 50% of combat deaths. A number of head simulants are described in the academic literature, in ballistic test methods for helmets (including measurement of behind helmet blunt trauma, BHBT) and in the 'open' and 'closed' government literature of several nations. The majority of these models are not anatomically correct and are not assessed with high-velocity rifle ammunition. In this article, an anatomically correct 'skull' (manufactured from polyurethane) and 'brain' (manufactured from 10%, by mass, gelatine) model for use in military wound ballistic studies is described. Filling the cranium completely with gelatine resulted in a similar 'skull' fracture pattern as an anatomically correct 'brain' combined with a representation of cerebrospinal fluid. In particular, posterior cranial fossa and occipital fractures and brain ejection were observed. This pattern of injury compared favourably to reported case studies of actual incidents in the literature.

Dynamics of correlations in long-range quantum systems follwing a quantum quench

NASA Astrophysics Data System (ADS)

Cevolani, Lorenzo; Carleo, Giuseppe; Sanchez-Palencia, Laurent

We study how and how fast correlations can spread in a quantum system abruptly driven out of equilibrium by a quantum quench. This protocol can be experimentally realized and it allow to address fundamental questions concerning the quasi-locality principle in isolated quantum systems with both short- and long-range interactions. We focus on two different models describing, respectively, lattice bosons, and spins. Our study is based on a combined approach, based on one hand on accurate many-body numerical calculations and on the other hand on a quasi-particle microscopic theory. We find that, for sufficiently fast decaying interaction potential the propagation is ballistic and the Lieb-Robinson bounds for long-range interactions are never attained. When the interactions are really long-range, the scenario is completely different in the two cases. In the bosonic system the locality is preserved and a ballistic propagation is still present while in the spin system an instantaneous propagation of correlations completely destroys locality. Using the microscopic point of view we can quantitatively describe all the different regimes, from instantaneous to ballistic, found in the spin model and we explain how locality is protected in the bosonic model leading to a ballistic propagation. ERC (FP7/2007-2013 No. 256294), QUIC (H2020 No. 641122).

Direct measurement of the ballistic motion of a freely floating colloid in Newtonian and viscoelastic fluids.

PubMed

Hammond, Andrew P; Corwin, Eric I

2017-10-01

A thermal colloid suspended in a liquid will transition from a short-time ballistic motion to a long-time diffusive motion. However, the transition between ballistic and diffusive motion is highly dependent on the properties and structure of the particular liquid. We directly observe a free floating tracer particle's ballistic motion and its transition to the long-time regime in both a Newtonian fluid and a viscoelastic Maxwell fluid. We examine the motion of the free particle in a Newtonian fluid and demonstrate a high degree of agreement with the accepted Clercx-Schram model for motion in a dense fluid. Measurements of the functional form of the ballistic-to-diffusive transition provide direct measurements of the temperature, viscosity, and tracer radius. We likewise measure the motion in a viscoelastic Maxwell fluid and find a significant disagreement between the theoretical asymptotic behavior and our measured values of the microscopic properties of the fluid. We observe a greatly increased effective mass for a freely moving particle and a decreased plateau modulus.

Complex Burn Region Module (CBRM) update

NASA Technical Reports Server (NTRS)

Adams, Carl L.; Jenkins, Billy

1991-01-01

Presented here is a Complex Burn Region Module (CBRM) update for the Solid Rocket Internal Ballistics Module (SRIBM) Program for the Advanced Solid Rocket Motor (ASRM) design/performance assessments. The goal was to develop an improved version of the solid rocket internal ballistics module program that contains a diversified complex region model for motor grain design, performance prediction, and evaluation.

BALLIST: A computer program to empirically predict the bumper thickness required to prevent perforation of the Space Station by orbital debris

NASA Technical Reports Server (NTRS)

Rule, William Keith

1991-01-01

A computer program called BALLIST that is intended to be a design tool for engineers is described. BALLlST empirically predicts the bumper thickness required to prevent perforation of the Space Station pressure wall by a projectile (such as orbital debris) as a function of the projectile's velocity. 'Ballistic' limit curves (bumper thickness vs. projectile velocity) are calculated and are displayed on the screen as well as being stored in an ASCII file. A Whipple style of spacecraft wall configuration is assumed. The predictions are based on a database of impact test results. NASA/Marshall Space Flight Center currently has the capability to generate such test results. Numerical simulation results of impact conditions that can not be tested (high velocities or large particles) can also be used for predictions.

Short Ballistic Josephson Coupling in Planar Graphene Junctions with Inhomogeneous Carrier Doping

NASA Astrophysics Data System (ADS)

Park, Jinho; Lee, Jae Hyeong; Lee, Gil-Ho; Takane, Yositake; Imura, Ken-Ichiro; Taniguchi, Takashi; Watanabe, Kenji; Lee, Hu-Jong

2018-02-01

We report on short ballistic (SB) Josephson coupling in junctions embedded in a planar heterostructure of graphene. Ballistic Josephson coupling is confirmed by the Fabry-Perot-type interference of the junction critical current Ic . The product of Ic and the normal-state junction resistance RN , normalized by the zero-temperature gap energy Δ0 of the superconducting electrodes, turns out to be exceptionally large close to 2, an indication of strong Josephson coupling in the SB junction limit. However, Ic shows a temperature dependence that is inconsistent with the conventional short-junction-like behavior based on the standard Kulik-Omel'yanchuk prediction. We argue that this feature stems from the effects of inhomogeneous carrier doping in graphene near the superconducting contacts, although the junction is in fact in the short-junction limit.

A numerical study of the nanoribbon field-effect transistors under the ballistic and dissipative transport

NASA Astrophysics Data System (ADS)

Ghoreishi, Seyed Saleh; Yousefi, Reza; Saghafi, Kamyar; Aderang, Habib

2017-08-01

In this article, a detailed performance comparison is made between ballistic and dissipative quantum transport of metal oxide semicondutor-like graphene nanoribbon field-effect transistor, in ON and OFF-state conditions. By the self-consistent mode-space non-equilibrium Green's function approach, inter- and intraband scattering is accounted and the role of acoustic and optical phonon scattering on the performance of the devices is evaluated. We found that in this structure the dominant mechanism of scattering changes according to the ranges of voltage bias. Under large biasing conditions, the influence of optical phonon scattering becomes important. Also, the ambipolar and OFF-current are impressed by the phonon-assisted band-to-band tunneling and increased considerably compared to the ballistic conditions, although sub-threshold swing degrades due to optical phonon scattering.

Ballistic Performance of Alimina/S-2 Glass-Reinforced Polymer-Matrix Composite Hybrid Lightweight Armor Against Armor Piercing (AP) and Non-AP Projectiles

DTIC Science & Technology

2007-01-01

and a phenolic -resin based polymeric matrix. Such armor panels offer superior protection against fragmented ballistic threats when compared to...database does not contain a material model for the HJ1 composite but provides a model for a Kevlar Fiber Reinforced Polymer (KFRP) containing 53 vol... phenolic resin and epoxy yield stresses and then with a ratio of the S-2 glass and aramid fibers volume fractions. To test the validity of the

Ballistic Simulation Method for Lithium Ion Batteries (BASIMLIB) Using Thick Shell Composites (TSC) in LS-DYNA

DTIC Science & Technology

2016-08-04

BAllistic SImulation Method for Lithium Ion Batteries (BASIMLIB) using Thick Shell Composites (TSC) in LS-DYNA Venkatesh Babu, Dr. Matt Castanier, Dr...Objective • Objective and focus of this work is to develop a – Robust simulation methodology to model lithium - ion based batteries in its module and full...unlimited  Lithium Ion Phosphate (LiFePO4) battery cell, module and pack was modeled in LS-DYNA using both Thin Shell Layer (TSL) and Thick Shell

Deterrent Concentration Measurement with FTIR and Subsequent Ballistic Performance in Medium Caliber Propellant

NASA Technical Reports Server (NTRS)

Furrow, Keith W.; Ritchie, Steve J.; Morris, Amy

2000-01-01

To meet ballistic requirements, medium and small caliber propellants use deterrent coatings to obtain burn rate progressivity. The required amount and distribution of deterrent varies between gun systems, propellant types, and often between lots. Micro Fourier Transform Infrared (FTIR) spectroscopy was used to measure deterrent gradients in RP36 propellants coated with methyl centralite (MC) at different deterrent levels and different processing conditions. The aromatic C-C bonds at 1496 cm(exp -1) wavenumber were used to monitor the deterrent profiles through the grain. Deterrent gradients measured with FTIR spectroscopy were then used to estimate burn rate gradients in the deterred grains. Burn rates were calculated from literature models and from closed bomb data of RP36 containing uniform deterrent concentration. Finally, the burn rate gradients were input into an IBHFG2 model of a 200 cc-closed bomb. The early flame spreading portion of the closed bomb ballistic cycle (0 to 0.2 P/Pmax) was roughly modeled by dividing the charge up into five propellant decks and igniting them at different times in the ballistic cycle. Pressure traces and vivacity curves from closed bomb shots were compared to predictions. In addition to the burn rate gradient, the closed bomb pressure trace was heavily dependent on ignition and flame spread. These two phenomena were not readily distinguishable from one another in deterred grains. The same RP-36 propellant was shot in a 25 mm M793TP round which was again modeled with IBHVG2. Peak pressure and muzzle velocity were accurately modeled when erosive burning effects were empirically factored into the model.

Ballistic missile precession frequency extraction by spectrogram's texture

NASA Astrophysics Data System (ADS)

Wu, Longlong; Xu, Shiyou; Li, Gang; Chen, Zengping

2013-10-01

In order to extract precession frequency, an crucial parameter in ballistic target recognition, which reflected the kinematical characteristics as well as structural and mass distribution features, we developed a dynamic RCS signal model for a conical ballistic missile warhead, with a log-norm multiplicative noise, substituting the familiar additive noise, derived formulas of micro-Doppler induced by precession motion, and analyzed time-varying micro-Doppler features utilizing time-frequency transforms, extracted precession frequency by measuring the spectrogram's texture, verified them by computer simulation studies. Simulation demonstrates the excellent performance of the method proposed in extracting the precession frequency, especially in the case of low SNR.

Acoustic ranging of small arms fire using a single sensor node collocated with the target.

PubMed

Lo, Kam W; Ferguson, Brian G

2015-06-01

A ballistic model-based method, which builds upon previous work by Lo and Ferguson [J. Acoust. Soc. Am. 132, 2997-3017 (2012)], is described for ranging small arms fire using a single acoustic sensor node collocated with the target, without a priori knowledge of the muzzle speed and ballistic constant of the bullet except that they belong to a known two-dimensional parameter space. The method requires measurements of the differential time of arrival and differential angle of arrival of the muzzle blast and ballistic shock wave at the sensor node. Its performance is evaluated using both simulated and real data.

High-speed Imaging of Global Surface Temperature Distributions on Hypersonic Ballistic-Range Projectiles

NASA Technical Reports Server (NTRS)

Wilder, Michael C.; Reda, Daniel C.

2004-01-01

The NASA-Ames ballistic range provides a unique capability for aerothermodynamic testing of configurations in hypersonic, real-gas, free-flight environments. The facility can closely simulate conditions at any point along practically any trajectory of interest experienced by a spacecraft entering an atmosphere. Sub-scale models of blunt atmospheric entry vehicles are accelerated by a two-stage light-gas gun to speeds as high as 20 times the speed of sound to fly ballistic trajectories through an 24 m long vacuum-rated test section. The test-section pressure (effective altitude), the launch velocity of the model (flight Mach number), and the test-section working gas (planetary atmosphere) are independently variable. The model travels at hypersonic speeds through a quiescent test gas, creating a strong bow-shock wave and real-gas effects that closely match conditions achieved during actual atmospheric entry. The challenge with ballistic range experiments is to obtain quantitative surface measurements from a model traveling at hypersonic speeds. The models are relatively small (less than 3.8 cm in diameter), which limits the spatial resolution possible with surface mounted sensors. Furthermore, since the model is in flight, surface-mounted sensors require some form of on-board telemetry, which must survive the massive acceleration loads experienced during launch (up to 500,000 gravities). Finally, the model and any on-board instrumentation will be destroyed at the terminal wall of the range. For these reasons, optical measurement techniques are the most practical means of acquiring data. High-speed thermal imaging has been employed in the Ames ballistic range to measure global surface temperature distributions and to visualize the onset of transition to turbulent-flow on the forward regions of hypersonic blunt bodies. Both visible wavelength and infrared high-speed cameras are in use. The visible wavelength cameras are intensified CCD imagers capable of integration times as short as 2 ns. The infrared camera uses an Indium Antimonide (InSb) sensor in the 3 to 5 micron band and is capable of integration times as short as 500 ns. The projectiles are imaged nearly head-on using expendable mirrors offset slightly from the flight path. The proposed paper will discuss the application of high-speed digital imaging systems in the NASA-Ames hypersonic ballistic range, and the challenges encountered when applying these systems. Example images of the thermal radiation from the blunt nose of projectiles flying at nearly 14 times the speed of sound will be given.

The September 14, 2015 phreatomagmatic eruption of Nakadake first crater, Aso Volcano, Japan: Eruption sequence inferred from ballistic, pyroclastic density current and fallout deposits

NASA Astrophysics Data System (ADS)

Miyabuchi, Yasuo; Iizuka, Yoshiyuki; Hara, Chihoko; Yokoo, Akihiko; Ohkura, Takahiro

2018-02-01

An explosive eruption occurred at Nakadake first crater, Aso Volcano in central Kyushu, southwestern Japan, on September 14, 2015. The sequence and causes of the eruption were reconstructed from the distribution, textures, grain-size, component and chemical characteristics of the related deposits, and video record. The eruptive deposits are divided into ballistics, pyroclastic density current and ash-fall deposits. A large number of ballistic clasts (mostly < 10 cm in diameter; maximum size 1.6 m) are scattered within about 500 m from the center of the crater. Almost half of the ballistics appear as fresh and unaltered basaltic andesite rocks interpreted to be derived from a fresh batch of magma, while the rest is weakly to highly altered clasts. A relatively thin ash derived from pyroclastic density currents covered an area of 2.3 km2 with the SE-trending main axis and two minor axes to the NE and NW. The pyroclastic density current deposit (maximum thickness < 10 cm even at the crater rim) is wholly fine grained, containing no block-sized clasts. Based on the isopach map, the mass of the pyroclastic density current deposit was estimated at ca. 5.2 × 104 tons. The ash-fall deposit is finer grained and clearly distributed to about 8 km west of the source crater. The mass of the ash-fall deposit was calculated at about 2.7 × 104 tons. Adding the mass of the pyroclastic density current deposit, the total discharged mass of the September 14, 2015 eruption was 7.9 × 104 tons. The September 14 pyroclastic density current and ash-fall deposits consist of glass shards (ca. 30%), crystals (20-30%) and lithic (40-50%) grains. Most glass shards are unaltered poorly crystallized pale brown glasses which probably resulted from quenching of juvenile magma. This suggests that the September 14, 2015 event at the Nakadake first crater was a phreatomagmatic eruption. Similar phreatomagmatic eruptions occurred at the same crater on September 6, 1979 and April 20, 1990 whose eruptive masses were one order larger than that of the September 14, 2015 eruption. These events highlight the potential hazard from phreatic or phreatomagmatic eruptions at Nakadake first crater, and provide useful information that will assist in preventing or mitigating future disasters at other similar volcanoes worldwide.

Mesoscopic Free Path of Nonthermalized Photogenerated Carriers in a Ferroelectric Insulator.

PubMed

Gu, Zongquan; Imbrenda, Dominic; Bennett-Jackson, Andrew L; Falmbigl, Matthias; Podpirka, Adrian; Parker, Thomas C; Shreiber, Daniel; Ivill, Mathew P; Fridkin, Vladimir M; Spanier, Jonathan E

2017-03-03

We show how finite-size scaling of a bulk photovoltaic effect-generated electric field in epitaxial ferroelectric insulating BaTiO_{3}(001) films and a photo-Hall response involving the bulk photovoltaic current reveal a large room-temperature mean free path of photogenerated nonthermalized electrons. Experimental determination of mesoscopic ballistic optically generated carrier transport opens a new paradigm for hot electron-based solar energy conversion, and for facile control of ballistic transport distinct from existing low-dimensional semiconductor interfaces, surfaces, layers, or other structures.

Terahertz Oscillations of Hot Electrons in Graphene

DTIC Science & Technology

2015-01-01

half the frequency ?F = 2?eF/~?OP , where 2?/?F is the time taken for carriers to accelerate ballistically to the optic phonon...resonance. Such resonance occurs at about half the frequency ωF = 2πeF/~ωOP , where 2π/ωF is the time taken for carriers to accelerate ballistically to the ... The current density on the plane is given by, Jx(t) = −4evF ∑ ~k f(~k, t) cos(φ), (2.16) where φ is the angle between ~k and the kx axis. Figure

Transverse isotropic modeling of the ballistic response of glass reinforced plastic composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, P.A.

1997-12-31

The use of glass reinforced plastic (GRP) composites is gaining significant attention in the DoD community for use in armor applications. These materials typically possess a laminate structure consisting of up to 100 plies, each of which is constructed of a glass woven roving fabric that reinforces a plastic matrix material. Current DoD attention is focused on a high strength, S-2 glass cross-weave (0/90) fabric reinforcing a polyester matrix material that forms each ply of laminate structure consisting anywhere from 20 to 70 plies. The resulting structure displays a material anisotropy that is, to a reasonable approximation, transversely isotropic. Whenmore » subjected to impact and penetration from a metal fragment projectile, the GRP displays damage and failure in an anisotropic manner due to various mechanisms such as matrix cracking, fiber fracture and pull-out, and fiber-matrix debonding. In this presentation, the author will describe the modeling effort to simulate the ballistic response of the GRP material described above using the transversely isotropic (TI) constitutive model which has been implemented in the shock physics code, CTH. The results of this effort suggest that the model is able to describe the delamination behavior of the material but has some difficulty capturing the in-plane (i.e., transverse) response of the laminate due to its cross-weave fabric reinforcement pattern which causes a departure from transverse isotropy.« less

Australian DefenceScience. Volume 15, Number 3, Spring

DTIC Science & Technology

2007-01-01

ignition, high pressure sealing, ignitor and propellent design, and ballistics instrumentation . Validation of simulation models of internal ballistics...supplementing visual information obtained by sources such as radiography and scanning electron microscopy, revealing details about features that are not...otherwise visible. Hence, it can assist with the inspection of vital component parts that are subject to high stresses, like aircraft engine turbine

A first proposal for a general description model of forensic traces

NASA Astrophysics Data System (ADS)

Lindauer, Ina; Schäler, Martin; Vielhauer, Claus; Saake, Gunter; Hildebrandt, Mario

2012-06-01

In recent years, the amount of digitally captured traces at crime scenes increased rapidly. There are various kinds of such traces, like pick marks on locks, latent fingerprints on various surfaces as well as different micro traces. Those traces are different from each other not only in kind but also in which information they provide. Every kind of trace has its own properties (e.g., minutiae for fingerprints, or raking traces for locks) but there are also large amounts of metadata which all traces have in common like location, time and other additional information in relation to crime scenes. For selected types of crime scene traces, type-specific databases already exist, such as the ViCLAS for sexual offences, the IBIS for ballistic forensics or the AFIS for fingerprints. These existing forensic databases strongly differ in the trace description models. For forensic experts it would be beneficial to work with only one database capable of handling all possible forensic traces acquired at a crime scene. This is especially the case when different kinds of traces are interrelated (e.g., fingerprints and ballistic marks on a bullet casing). Unfortunately, current research on interrelated traces as well as general forensic data models and structures is not mature enough to build such an encompassing forensic database. Nevertheless, recent advances in the field of contact-less scanning make it possible to acquire different kinds of traces with the same device. Therefore the data of these traces is structured similarly what simplifies the design of a general forensic data model for different kinds of traces. In this paper we introduce a first common description model for different forensic trace types. Furthermore, we apply for selected trace types from the well established database schema development process the phases of transferring expert knowledge in the corresponding forensic fields into an extendible, database-driven, generalised forensic description model. The trace types considered here are fingerprint traces, traces at locks, micro traces and ballistic traces. Based on these basic trace types, also combined traces (multiple or overlapped fingerprints, fingerprints on bullet casings, etc) and partial traces are considered.

Trismus in Face Transplantation Following Ballistic Trauma.

PubMed

Krezdorn, Nicco; Alhefzi, Muayyad; Perry, Bridget; Aycart, Mario A; Tasigiorgos, Sotirios; Bueno, Ericka M; Green, Jordan R; Pribaz, Julian J; Pomahac, Bohdan; Caterson, Edward J

2018-06-01

Trismus can be a challenging consequence of ballistic trauma to the face, and has rarely been described in the setting of face transplantation. Almost half of all current face transplant recipients in the world received transplantation to restore form and function after a ballistic injury. Here we report our experience and challenges with long standing trismus after face transplantation. We reviewed the medical records of our face transplant recipients whose indication was ballistic injury. We focused our review on trismus and assessed the pre-, peri- and postoperative planning, surgery and functional outcomes. Two patients received partial face transplantation, including the midface for ballistic trauma. Both patients suffered from impaired mouth opening, speech intelligibility, and oral competence. Severe scarring of the temporomandibular joint (TMJ) required intraoperative release in both patients, and additional total condylectomy on the left side 6 months posttransplant for 1 patient. Posttransplant, both patients achieved an improvement in mouth opening; however, there was persistent trismus. One year after transplantation, range of motion of the jaw had improved for both patients. Independent oral food intake was possible 1 year after surgery, although spillage of liquids and mixed consistency solids persisted. Speech intelligibility testing showed impairments in the immediate postoperative period, with improvement to over 85% for both patients at 1 year posttransplant. Ballistic trauma to the face and subsequent reconstructive measures can cause significant scarring and covert injuries to structures such as the TMJ, resulting in long standing trismus. Meticulous individual planning prior to interventions such as face transplantation must take these into account. We encourage intraoperative evaluation of these structures as well as peri- and postoperative treatment when necessary. Due to the nature of the primary injury, functional outcomes after face transplantation in these patients may differ substantially from those of other indications.

The effects of a single bout of exercise on motor memory interference in the trained and untrained hemisphere.

PubMed

Lauber, Benedikt; Franke, Steffen; Taube, Wolfgang; Gollhofer, Albert

2017-04-07

Increasing evidence suggests that cardiovascular exercise has positive effects on motor memory consolidation. In this study, we investigated whether a single session of high-intensity interval training (HIIT) mitigates the effects of practicing an interfering motor task. Furthermore, learning and interference effects were assessed in the actively trained and untrained limb as it is known that unilateral motor learning can cause bilateral adaptations. Subjects performed a ballistic training and then the HIIT either before (HIIT_before) or after (HIIT_after) practicing an interfering accuracy task (AT). The control group (No_HIIT) did not participate in the HIIT but rested instead. Performance in the ballistic task (BT) was tested before and after the ballistic training, after the exercise and practice of the AT and 24h later. After ballistic training, all groups showed comparable increases in performance in the trained and untrained limb. Despite the practice of the AT, HIIT_before maintained their BT performance after the high-intensity interval training whereas HIIT_after (trend) & No_HIIT showed prominent interference effects. After 24h, HIIT_before still did not show any interference effects but further improved ballistic motor performance. HIIT_after counteracted the interference resulting in a comparable BT performance after 24h than directly after the ballistic training while No_HIIT had a significantly lower BT performance in the retention test. The results were similar in the trained and untrained limb. The current results imply that a single session of cardiovascular exercise can prevent motor interference in the trained and untrained hemisphere. Overall learning was best, and interference least, when HIIT was performed before the interfering motor task. Copyright © 2017 IBRO. Published by Elsevier Ltd. All rights reserved.

Ballistic heat conduction and mass disorder in one dimension.

PubMed

Ong, Zhun-Yong; Zhang, Gang

2014-08-20

It is well-known that in the disordered harmonic chain, heat conduction is subballistic and the thermal conductivity (κ) scales asymptotically as lim(L--> ∞) κ ∝ L(0.5) where L is the chain length. However, using the nonequilibrium Green's function (NEGF) method and analytical modelling, we show that there exists a critical crossover length scale (LC) below which ballistic heat conduction (κ ∝ L) can coexist with mass disorder. This ballistic-to-subballistic heat conduction crossover is connected to the exponential attenuation of the phonon transmittance function Ξ i.e. Ξ(ω, L) = exp[-L/λ(ω)], where λ is the frequency-dependent attenuation length. The crossover length can be determined from the minimum attenuation length, which depends on the maximum transmitted frequency. We numerically determine the dependence of the transmittance on frequency and mass composition as well as derive a closed form estimate, which agrees closely with the numerical results. For the length-dependent thermal conductance, we also derive a closed form expression which agrees closely with numerical results and reproduces the ballistic to subballistic thermal conduction crossover. This allows us to characterize the crossover in terms of changes in the length, mass composition and temperature dependence, and also to determine the conditions under which heat conduction enters the ballistic regime. We describe how the mass composition can be modified to increase ballistic heat conduction.

Does preliminary optimisation of an anatomically correct skull-brain model using simple simulants produce clinically realistic ballistic injury fracture patterns?

PubMed

Mahoney, P F; Carr, D J; Delaney, R J; Hunt, N; Harrison, S; Breeze, J; Gibb, I

2017-07-01

Ballistic head injury remains a significant threat to military personnel. Studying such injuries requires a model that can be used with a military helmet. This paper describes further work on a skull-brain model using skulls made from three different polyurethane plastics and a series of skull 'fills' to simulate brain (3, 5, 7 and 10% gelatine by mass and PermaGel™). The models were subjected to ballistic impact from 7.62 × 39 mm mild steel core bullets. The first part of the work compares the different polyurethanes (mean bullet muzzle velocity of 708 m/s), and the second part compares the different fills (mean bullet muzzle velocity of 680 m/s). The impact events were filmed using high speed cameras. The resulting fracture patterns in the skulls were reviewed and scored by five clinicians experienced in assessing penetrating head injury. In over half of the models, one or more assessors felt aspects of the fracture pattern were close to real injury. Limitations of the model include the skull being manufactured in two parts and the lack of a realistic skin layer. Further work is ongoing to address these.

Current-driven plasmonic boom instability in three-dimensional gated periodic ballistic nanostructures

NASA Astrophysics Data System (ADS)

Aizin, G. R.; Mikalopas, J.; Shur, M.

2016-05-01

An alternative approach of using a distributed transmission line analogy for solving transport equations for ballistic nanostructures is applied for solving the three-dimensional problem of electron transport in gated ballistic nanostructures with periodically changing width. The structures with varying width allow for modulation of the electron drift velocity while keeping the plasma velocity constant. We predict that in such structures biased by a constant current, a periodic modulation of the electron drift velocity due to the varying width results in the instability of the plasma waves if the electron drift velocity to plasma wave velocity ratio changes from below to above unity. The physics of such instability is similar to that of the sonic boom, but, in the periodically modulated structures, this analog of the sonic boom is repeated many times leading to a larger increment of the instability. The constant plasma velocity in the sections of different width leads to resonant excitation of the unstable plasma modes with varying bias current. This effect (that we refer to as the superplasmonic boom condition) results in a strong enhancement of the instability. The predicted instability involves the oscillating dipole charge carried by the plasma waves. The plasmons can be efficiently coupled to the terahertz electromagnetic radiation due to the periodic geometry of the gated structure. Our estimates show that the analyzed instability should enable powerful tunable terahertz electronic sources.

Volcanic Lightning, Pyroclastic Density Currents, Ballistic Fall, Vent Tremor, and One Very Loud Blast: Acoustic Analysis of the 14 July 2013 Vulcanian Eruption at Tungurahua, Ecuador.

NASA Astrophysics Data System (ADS)

Anderson, J.; Johnson, J. B.; Steele, A. L.; Anzieta, J. C.; Ortiz, H. D.; Hall, M. L.; Ruiz, M. C.

2014-12-01

Acoustic recordings reveal a variety of volcanic activities during an exceptionally loud vulcanian eruption at Tungurahua. A period of several months of mild surface activity came to an abrupt end with the emission of a powerful blast wave heard at least 180 km away. Sensors 2080 m from the vent recorded a stepped rise to its maximum overpressure of 1220 Pa (corresponding to a sound pressure level of 156 dB) and its unusually long dominant period of 5.6 s. We discuss source processes that produced the blast wave, considering that wave propagation could be nonlinear near the vent because of high overpressures. More than an hour of acoustic activity was recorded after the blast wave, including sound from falling ballistics, reflections of the blast wave from nearby mountains, pyroclastic density currents, and acoustic tremor at the vent. Glitches in the acoustic records related to plume lightning were also serendipitously observed, although thunder could not be unambiguously identified. We discuss acoustic signatures of falling ballistics and pyroclastic density currents and how array-style deployments and analytic methods can be used to reveal them. Placement of sensors high on the volcano's slopes facilitated resolving these distinct processes. This study demonstrates that near-vent, array-style acoustic installations can be used to monitor various types of volcanic activity.

[Ballistic concepts and management of gunshot wounds at members].

PubMed

Fabeck, L; Hock, N; Goffin, J; Ngatchou, W

2017-01-01

Ballistic trauma is not the prerogative of battlefields and currently extends to civil environments. Any surgeon or emergency room can be faced with such trauma whose management requires an understanding of wound ballistics. The aim of this retrospective is reviewing the management of ballistic trauma within the C.H.U. Saint-Pierre hospital over a period of ten years. Data recorded included demographics data, lesions, clinical parameters, imaging, treatment and outcome. It appears that the wounds of the members have a low mortality rate but a significant rate of complications. Patients should be managed according to the ATLS protocol and according hemodynamic stability and location of the injury, benefit from imaging. Unstable patients will be operated in emergency, stable patients will be treated according to the extent of damage and the type of fracture either conservatively or by external fixator and intramedullary centromedullary. Debridement and antibiotics are recommended as a nerve exploration if there is a peripheral paralysis. The management of trauma in our sample appear not optimal in light of the literature especially in terms of setting the vascular point of debridement, antibiotic and nerve repair resulting in significant consequences. Two management protocols according to patients' hemodynamic status are offered.

Upgrades and Modifications of the NASA Ames HFFAF Ballistic Range

NASA Technical Reports Server (NTRS)

Bogdanoff, David W.; Wilder, Michael C.; Cornelison, Charles J.; Perez, Alfredo J.

2017-01-01

The NASA Ames Hypervelocity Free Flight Aerodynamics Facility ballistic range is described. The various configurations of the shadowgraph stations are presented. This includes the original stations with film and configurations with two different types of digital cameras. Resolution tests for the 3 shadowgraph station configurations are described. The advantages of the digital cameras are discussed, including the immediate availability of the shadowgraphs. The final shadowgraph station configuration is a mix of 26 Nikon cameras and 6 PI-MAX2 cameras. Two types of trigger light sheet stations are described visible and IR. The two gunpowders used for the NASA Ames 6.251.50 light gas guns are presented. These are the Hercules HC-33-FS powder (no longer available) and the St. Marks Powder WC 886 powder. The results from eight proof shots for the two powders are presented. Both muzzle velocities and piston velocities are 5 9 lower for the new St. Marks WC 886 powder than for the old Hercules HC-33-FS powder (no longer available). The experimental and CFD (computational) piston and muzzle velocities are in good agreement. Shadowgraph-reading software that employs template-matching pattern recognition to locate the ballistic-range model is described. Templates are generated from a 3D solid model of the ballistic-range model. The accuracy of the approach is assessed using a set of computer-generated test images.

Surgeon preferences regarding antibiotic prophylaxis for ballistic fractures.

PubMed

Marecek, Geoffrey S; Earhart, Jeffrey S; Gardner, Michael J; Davis, Jason; Merk, Bradley R

2016-06-01

Scant evidence exists to support antibiotic use for low velocity ballistic fractures (LVBF). We therefore sought to define current practice patterns. We hypothesized that most surgeons prescribe antibiotics for LVBF, prescribing is not driven by institutional protocols, and that decisions are based on protocols utilized for blunt trauma. A web-based questionnaire was emailed to the membership of the Orthopaedic Trauma Association (OTA). The questionnaire included demographic information and questions about LVBF treatment practices. Two hundred and twenty surgeons responded. One hundred and fifty-four (70 %) respondents worked at a Level-1 trauma center, 176 (80 %) had received fellowship education in orthopaedic trauma and 104 (47 %) treated at least 10 ballistic fractures annually. Responses were analyzed with SAS 9.3 for Windows (SAS Institute Inc, Cary, NC). One hundred eighty-six respondents (86 %) routinely provide antibiotics for LVBF. Those who did not were more apt to do so for intra-articular fractures (8/16, 50 %) and pelvic fractures with visceral injury (10/16, 63 %). Most surgeons (167, 76 %) do not believe the Gustilo-Anderson classification applies to ballistic fractures, and (20/29, 70 %) do not base their antibiotic choice on the classification system. Few institutions (58, 26 %) have protocols guiding antibiotic use for LVBF. Routine antibiotic use for LVBF is common; however, practice is not dictated by institutional protocol. Although antibiotic use generally follows current blunt trauma guidelines, surgeons do not base their treatment decisions the Gustilo-Anderson classification. Given the high rate of antibiotic use for LVBF, further study should focus on providing evidence-based treatment guidelines.

Ballistic magnetotransport in a suspended two-dimensional electron gas with periodic antidot lattices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhdanov, E. Yu., E-mail: zhdanov@isp.nsc.ru; Pogosov, A. G.; Budantsev, M. V.

2017-01-15

The magnetoresistance of suspended semiconductor nanostructures with a two-dimensional electron gas structured by periodic square antidot lattices is studied. It is shown that the ballistic regime of electron transport is retained after detaching the sample from the substrate. Direct comparative analysis of commensurability oscillations of magnetoresistance and their temperature dependences in samples before and after suspension is performed. It is found that the temperature dependences are almost identical for non-suspended and suspended samples, whereas significant differences are observed in the nonlinear regime, caused by direct current passage. Commensurability oscillations in the suspended samples are more stable with respect to exposuremore » to direct current, which can be presumably explained by electron–electron interaction enhancement after detaching nanostructures from the high-permittivity substrate.« less

[Wound Ballistics – a Brief Overview].

PubMed

Bolliger, Stephan A; Eggert, Sebastian; Thali, Michael J

2016-02-03

Wound ballistics examines the specific effect, namely the wound profile, of bullets on the body by firing at synthetic models made of ordnance gelatine, glycerin soap and synthetic bones, validated with real cases from (battlefield) surgery and forensic pathology. Wound profile refers to the penetration depth, the bullet deformation/ fragmentation, the diameter of the permanent and the temporary wound cavity. Knowing these features and the used ammunition a surgeon can rapidly assess the amount damage within a patient. The forensic pathologist can draw conclusions as to the used ammunition based on the wound profile. By measuring of the destructive capability of different ammunition types, wound ballistics lays the foundation for guidelines concerning the maximum effect of military ammunition.

The Effect of Aerodynamic Heating on Air Penetration by Shaped Charge Jets and Their Particles

NASA Astrophysics Data System (ADS)

Backofen, Joseph

2009-06-01

The goal of this paper is to present recent work modeling thermal coupling between shaped charge jets and their particles with air while it is being penetrated to form a crater that subsequently collapses back onto the jet. This work complements research published at International Symposia on Ballistics: 1) 1987 - Shaped Charge Jet Aerodynamics, Particulation and Blast Field Modeling; and 2) 2007 - Air Cratering by Eroding Shaped Charge Jets. The current work shows how and when a shaped charge jet's tip and jet particles are softened enough that they can erode in a hydrodynamic manner as modeled in these papers. This paper and its presentation includes models for heat transfer from shocked air as a function of jet velocity as well as heat flow within the jet or particle. The work is supported by an extensive bibliographic search including publications on meteors and ballistic missile re-entry vehicles. The modeling shows that a jet loses its strength to the depth required to justify hydrodynamic erosion when its velocity is above a specific velocity related to the shock properties of air and the jet material's properties. As a result, the portion of a jet's kinetic energy converted at the aerodynamic shock into heating transferred back onto the jet affects the energy deposited into the air through drag and ablation which in turn affect air crater expansion and subsequent collapse back onto the jet and its particles as shown in high-speed photography.

How "Hot Precursors" Modify Island Nucleation: A Rate-Equation Model

NASA Astrophysics Data System (ADS)

Morales-Cifuentes, Josue R.; Einstein, T. L.; Pimpinelli, A.

2014-12-01

We propose a novel island nucleation and growth model explicitly including transient (ballistic) mobility of the monomers deposited at rate F , assumed to be in a hot precursor state before thermalizing. In limiting regimes, corresponding to fast (diffusive) and slow (ballistic) thermalization, the island density N obeys scaling N ∝Fα . In between is found a rich, complex behavior, with various distinctive scaling regimes, characterized by effective exponents αeff and activation energies that we compute exactly. Application to N (F ,T ) of recent organic-molecule deposition experiments yields an excellent fit.

U.S. Arms Control Objectives and the Implications for Ballistic Missile Defense. Proceedings of a Symposium Held at the Center for Science and International Affairs, Harvard University, November 1-2, 1979.

DTIC Science & Technology

1980-06-30

are no firm indications that the Soviet Union in- tends to expand this sytem to the full 100 launchers permitted under the ABM Treaty. Although the...Ballistic Missile Defense; Arms Control; ABM Treaty; SALT ABSTRACT (Continue on reverse eid@ If necessary and Identify by block number) IvOn November 1-2...the significance of constraints imposed by the ABM Treaty on the implementation of current and planned BMD R&D programs; (4) to explore the status of

Ballistic and resonant negative photocurrents in semiconducting carbon nanotubes

NASA Astrophysics Data System (ADS)

Karnetzky, Christoph; Sponfeldner, Lukas; Engl, Max; Holleitner, Alexander W.

2017-04-01

Ultrafast photocurrent experiments are performed on semiconducting, single-walled carbon nanotubes under a resonant optical excitation of their subbands. The photogenerated excitons are dissociated at large electric fields and the resulting transport of the charge carriers turns out to be ballistic. Thermionic emission processes to the contacts dominate the photocurrent amplitude. The charge current without laser excitation is well described by a Fowler-Nordheim tunneling. The time-averaged photocurrent changes polarity as soon as sufficient charge carriers are injected from the contacts, which can be explained by an effective population inversion in the optically pumped subbands.

Ballistic and resonant negative photocurrents in single carbon nanotubes

NASA Astrophysics Data System (ADS)

Karnetzky, Christoph; Sponfeldner, Lukas; Engl, Max; Holleitner, Alexander W.

We present ultrafast photocurrent experiments on semiconducting, single-walled carbon nanotubes under a resonant optical excitation of their subbands. We demonstrate that a ballistic transport of the photogenerated charge carriers can be achieved. Moreover, thermionic emission processes to the contacts dominate the photocurrent. In contrast, the charge current without laser excitation is well described by a Fowler-Nordheim tunneling. The time-averaged photocurrent changes polarity as soon as sufficient charge carriers are injected from the contacts, which can be explained by an effective population inversion in the optically pumped subbands. We acknowledge the ERC via the project NanoREAL.

Impulse-variability theory: implications for ballistic, multijoint motor skill performance.

PubMed

Urbin, M A; Stodden, David F; Fischman, Mark G; Weimar, Wendi H

2011-01-01

Impulse-variability theory (R. A. Schmidt, H. N. Zelaznik, B. Hawkins, J. S. Frank, & J. T. Quinn, 1979) accounts for the curvilinear relationship between the magnitude and resulting variability of the muscular forces that influence the success of goal-directed limb movements. The historical roots of impulse-variability theory are reviewed in the 1st part of this article, including the relationship between movement speed and spatial error. The authors then address the relevance of impulse-variability theory for the control of ballistic, multijoint skills, such as throwing, striking, and kicking. These types of skills provide a stark contrast to the relatively simple, minimal degrees of freedom movements that characterized early research. However, the inherent demand for ballistic force generation is a strong parallel between these simple laboratory tasks and multijoint motor skills. Therefore, the authors conclude by recommending experimental procedures for evaluating the adequacy of impulse variability as a theoretical model within the context of ballistic, multijoint motor skill performance. Copyright © Taylor & Francis Group, LLC

The impact of defect scattering on the quasi-ballistic transport of nanoscale conductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Esqueda, I. S., E-mail: isanchez@isi.edu; Fritze, M.; Cress, C. D.

2015-02-28

Using the Landauer approach for carrier transport, we analyze the impact of defects induced by ion irradiation on the transport properties of nanoscale conductors that operate in the quasi-ballistic regime. Degradation of conductance results from a reduction of carrier mean free path due to the introduction of defects in the conducting channel. We incorporate scattering mechanisms from radiation-induced defects into calculations of the transmission coefficient and present a technique for extracting modeling parameters from near-equilibrium transport measurements. These parameters are used to describe degradation in the transport properties of nanoscale devices using a formalism that is valid under quasi-ballistic operation.more » The analysis includes the effects of bandstructure and dimensionality on the impact of defect scattering and discusses transport properties of nanoscale devices from the diffusive to the ballistic limit. We compare calculations with recently published measurements of irradiated nanoscale devices such as single-walled carbon nanotubes, graphene, and deep-submicron Si metal-oxide-semiconductor field-effect transistors.« less

Effect of Mesoscale and Multiscale Modeling on the Performance of Kevlar Woven Fabric Subjected to Ballistic Impact: A Numerical Study

NASA Astrophysics Data System (ADS)

Jia, Xin; Huang, Zhengxiang; Zu, Xudong; Gu, Xiaohui; Xiao, Qiangqiang

2013-12-01

In this study, an optimal finite element model of Kevlar woven fabric that is more computational efficient compared with existing models was developed to simulate ballistic impact onto fabric. Kevlar woven fabric was modeled to yarn level architecture by using the hybrid elements analysis (HEA), which uses solid elements in modeling the yarns at the impact region and uses shell elements in modeling the yarns away from the impact region. Three HEA configurations were constructed, in which the solid element region was set as about one, two, and three times that of the projectile's diameter with impact velocities of 30 m/s (non-perforation case) and 200 m/s (perforation case) to determine the optimal ratio between the solid element region and the shell element region. To further reduce computational time and to maintain the necessary accuracy, three multiscale models were presented also. These multiscale models combine the local region with the yarn level architecture by using the HEA approach and the global region with homogenous level architecture. The effect of the varying ratios of the local and global area on the ballistic performance of fabric was discussed. The deformation and damage mechanisms of fabric were analyzed and compared among numerical models. Simulation results indicate that the multiscale model based on HEA accurately reproduces the baseline results and obviously decreases computational time.

Supercomputing in Aerospace

NASA Technical Reports Server (NTRS)

Kutler, Paul; Yee, Helen

1987-01-01

Topics addressed include: numerical aerodynamic simulation; computational mechanics; supercomputers; aerospace propulsion systems; computational modeling in ballistics; turbulence modeling; computational chemistry; computational fluid dynamics; and computational astrophysics.

The quantified evaluation of the wounding potential of a ricochet projectile of a handgun cartridge calibre 9 mm (type 82) in a ballistic experiment.

PubMed

Moravanský, Norbert; Rekeň, Viktor; Juříček, Ludvík; Zummerová, Anežka; Kováč, Peter

2013-01-01

The question of handgun use in a city or densely populated aglomerations requires a highly practical level of solution to this issue, though with the knowledge of theoretical presumptions of wound ballistics of ricochet projectiles. The application of wound ballistics into the practice of a forensic pathologist, as well as a surgeon or a traumatologist, enables a good understanding of the dynamics of projectile penetration through anatomic structures of the human body. In forensic assessment, gunshot wounds of limbs are relatively frequent cases. By the integration of wound ballistics principles into the research of gunshot wounds, it is also possible to establish, whether the projectile entered into the anatomic structures under direct trajectory steadily or whether through the course of its trajectory, before reaching the human body, it firstly contacted a particular object in the space, i. e. whether the injury could have been caused by a ricochet projectile. In connection with unclear gunshot wounds and their morphological image, it is necessary to consider the possibility of the effects of a ricochet projectile, especially when persons are injured accidentally. The daily practice of the officers of the Police Corps of the Slovak Republic essentially enhances the necessity of being informed about the behaviour of parametrically designated ricochet projectiles in a ballistic experiment with the use of a model of a built-up area in a town, with typical materials and surfaces of objects in between and a model of a human limb part as a potential target of an uncontrolled ricochet projectile. The proposed design of the situation is undoubtedly of an enormous significance, even when forensically evaluating the morphological consequences of ricochet projectiles. By the application of results of such experiments and their final comparison, when different types of projectiles are used, it is also possible to contribute to the experts groundwork in the process of rearmament of the official armed forces. The main aim of our work is to point out the high potential of the wounding effect of ricochet bullets of a particular calibre cartridge with focus on injuries of the femurs of the lower limbs. The carried out ballistic experiment was designed for the needs of the experimental part of a diploma thesis of a student from the Faculty of Medicine of Comenius University in Bratislava and his results point out at the possibilities for civilian safety strategies during the intervention of the armed forces as well. Terminal ballistics - Ballistic experiment - Ricochet projectile - Gunshot wounds.

Model-based analysis of fatigued human knee extensors : Effects of isometrically induced fatigue on Hill-type model parameters and ballistic contractions.

PubMed

Penasso, Harald; Thaller, Sigrid

2018-05-05

This study investigated the effect of isometrically induced fatigue on Hill-type muscle model parameters and related task-dependent effects. Parameter identification methods were used to extract fatigue-related parameter trends from isometric and ballistic dynamic maximum voluntary knee extensions. Nine subjects, who completed ten fatiguing sets, each consisting of nine 3 s isometric maximum voluntary contractions with 3 s rest plus two ballistic contractions with different loads, were analyzed. Only at the isometric task, the identified optimized model parameter values of muscle activation rate and maximum force generating capacity of the contractile element decreased from [Formula: see text] to [Formula: see text] Hz and from [Formula: see text] to [Formula: see text] N, respectively. For all tasks, the maximum efficiency of the contractile element, mathematically related to the curvature of the force-velocity relation, increased from [Formula: see text] to [Formula: see text]. The model parameter maximum contraction velocity decreased from [Formula: see text] to [Formula: see text] m/s and the stiffness of the serial elastic element from [Formula: see text] to [Formula: see text] N/mm. Thus, models of fatigue should consider fatigue dependencies in active as well as in passive elements, and muscle activation dynamics should account for the task dependency of fatigue.

Materials Database Development for Ballistic Impact Modeling

NASA Technical Reports Server (NTRS)

Pereira, J. Michael

2007-01-01

A set of experimental data is being generated under the Fundamental Aeronautics Program Supersonics project to help create and validate accurate computational impact models of jet engine impact events. The data generated will include material property data generated at a range of different strain rates, from 1x10(exp -4)/sec to 5x10(exp 4)/sec, over a range of temperatures. In addition, carefully instrumented ballistic impact tests will be conducted on flat plates and curved structures to provide material and structural response information to help validate the computational models. The material property data and the ballistic impact data will be generated using materials from the same lot, as far as possible. It was found in preliminary testing that the surface finish of test specimens has an effect on measured high strain rate tension response of AL2024. Both the maximum stress and maximum elongation are greater on specimens with a smoother finish. This report gives an overview of the testing that is being conducted and presents results of preliminary testing of the surface finish study.

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems, Phase II. Part 2; Ballistic Impact Testing

NASA Technical Reports Server (NTRS)

Revilock, D. M.; Pereira, J. M.

2009-01-01

This report summarizes the ballistic impact testing that was conducted to provide validation data for the development of numerical models of blade-out events in fabric containment systems. The ballistic impact response of two different fiber materials - Kevlar(TradeName) 49 and Zylon(TradeName) AS (as spun) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation, and velocity of the projectile were varied and recorded. In most cases, the tests were designed so the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models to predict the response of fabrics under conditions that simulate those of a jet engine blade-release situation. In addition, some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different fabric materials.

FAA Development of Reliable Modeling Methodologies for Fan Blade Out Containment Analysis. Part 2; Ballistic Impact Testing

NASA Technical Reports Server (NTRS)

Revilock, Duane M.; Pereira, J. Michael

2008-01-01

This report summarizes the ballistic impact testing that was conducted to provide validation data for the development of numerical models of blade out events in fabric containment systems. The ballistic impact response of two different fiber materials - Kevlar 49 (E.I. DuPont Nemours and Company) and Zylon AS (Toyobo Co., Ltd.) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation and velocity of the projectile were varied and recorded. In most cases the tests were designed such that the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models for predicting the response of fabrics under conditions simulating those of a jet engine blade release situations. In addition some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different materials.

HVI Ballistic Limit Charaterization of Fused Silica Thermal Pane

NASA Technical Reports Server (NTRS)

Bohl, William E.; Miller, Joshua E.; Christiansen, Eric L.; Deighton, Kevin.; Davis, Bruce

2015-01-01

The Orion spacecraft's windows are exposed to the micrometeroid and orbital debris (MMOD) space environments while in space as well as the Earth entry environment at the mission's conclusion. The need for a low-mass spacecraft window design drives the need to reduce conservatism when assessing the design for loss of crew due to MMOD impact and subsequent Earth entry. Therefore, work is underway at NASA and Lockheed Martin to improve characterization of the complete penetration ballistic limit of an outer fused silica thermal pane. Hypervelocity impact tests of the window configuration at up to 10 km/s and hydrocode modeling have been performed with a variety of projectile materials to enable refinement of the fused silica ballistic limit equation.

Dynamic Stability Analysis of Blunt Body Entry Vehicles Using Time-Lagged Aftbody Pitching Moments

NASA Technical Reports Server (NTRS)

Kazemba, Cole D.; Braun, Robert D.; Schoenenberger, Mark; Clark, Ian G.

2013-01-01

This analysis defines an analytic model for the pitching motion of blunt bodies during atmospheric entry. The proposed model is independent of the pitch damping sum coefficient present in the standard formulation of the equations of motion describing pitch oscillations of a decelerating blunt body, instead using the principle of a time-lagged aftbody moment as the forcing function for oscillation divergence. Four parameters, all with intuitive physical relevance, are introduced to fully define the aftbody moment and the associated time delay. It is shown that the dynamic oscillation responses typical to blunt bodies can be produced using hysteresis of the aftbody moment in place of the pitch damping coefficient. The approach used in this investigation is shown to be useful in understanding the governing physical mechanisms for blunt body dynamic stability and in guiding vehicle and mission design requirements. A validation case study using simulated ballistic range test data is conducted. From this, parameter identification is carried out through the use of a least squares optimizing routine. Results show good agreement with the limited existing literature for the parameters identified, suggesting that the model proposed could be validated by an experimental ballistic range test series. The trajectories produced by the identified parameters were found to match closely those from the MER ballistic range tests for a wide array of initial conditions and can be identified with a reasonable number of ballistic range shots and computational effort.

Solid propellant rocket motor internal ballistics performance variation analysis, phase 3

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Foster, W. A., Jr.; Murph, J. E.; Adams, G. W., Jr.

1977-01-01

Results of research aimed at improving the predictability of off nominal internal ballistics performance of solid propellant rocket motors (SRMs) including thrust imbalance between two SRMs firing in parallel are reported. The potential effects of nozzle throat erosion on internal ballistic performance were studied and a propellant burning rate low postulated. The propellant burning rate model when coupled with the grain deformation model permits an excellent match between theoretical results and test data for the Titan IIIC, TU455.02, and the first Space Shuttle SRM (DM-1). Analysis of star grain deformation using an experimental model and a finite element model shows the star grain deformation effects for the Space Shuttle to be small in comparison to those of the circular perforated grain. An alternative technique was developed for predicting thrust imbalance without recourse to the Monte Carlo computer program. A scaling relationship used to relate theoretical results to test results may be applied to the alternative technique of predicting thrust imbalance or to the Monte Carlo evaluation. Extended investigation into the effect of strain rate on propellant burning rate leads to the conclusion that the thermoelastic effect is generally negligible for both steadily increasing pressure loads and oscillatory loads.

Self-pinched lithium beam transport experiments on SABRE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, D.L.; Olson, C.L.; Poukey, J.W.

Self-pinched transport of ion beams has many advantages for ion-driven ICF applications involving high yield and energy production. The authors are currently preparing for a self-pinched lithium beam transport experiment on the SABRE accelerator. There are three transport elements that must eventually be demonstrated: (1) efficient lithium beam generation and ballistic transport to a focus at the self-pinched transport channel entrance; (2) self-pinched transport in the channel, requiring optimized injection conditions and gas breakdown; and (3) self-pinched transport of the equilibrated beam from the channel into free space, with associated aiming and stability considerations. In the present experiment, a hollowmore » annular lithium beam from an applied-B extraction ion diode will be focused to small radius (r {le} 2 cm) in a 60 cm long ballistic focus section containing argon gas at a pressure of a few Torr. The self-pinched transport channel will contain a low pressure background gas of 10--40 mTorr argon to allow sufficient net current to confine the beam for long distance transport. IPROP simulations are in progress to optimize the design of the ballistic and self-pinched transport sections. Progress on preparation of this lithium self-pinched transport experiment, including a discussion of transport system design, important gas breakdown issues, and diagnostics, will be presented.« less

New Diagnostic, Launch and Model Control Techniques in the NASA Ames HFFAF Ballistic Range

NASA Technical Reports Server (NTRS)

Bogdanoff, David W.

2012-01-01

This report presents new diagnostic, launch and model control techniques used in the NASA Ames HFFAF ballistic range. High speed movies were used to view the sabot separation process and the passage of the model through the model splap paper. Cavities in the rear of the sabot, to catch the muzzle blast of the gun, were used to control sabot finger separation angles and distances. Inserts were installed in the powder chamber to greatly reduce the ullage volume (empty space) in the chamber. This resulted in much more complete and repeatable combustion of the powder and hence, in much more repeatable muzzle velocities. Sheets of paper or cardstock, impacting one half of the model, were used to control the amplitudes of the model pitch oscillations.

[Fundamental biological model for trials of wound ballistics].

PubMed

Krajsa, J; Hirt, M

2006-10-01

The aim of our experiment was the testing of effects of common ammunition on usable and slightly accessible biological tissue thereby to create fundamental simple biological model for trials of wounded ballistic. Like objective tissue was elected biological material - pork and beef hind-limbs, pork head, pork bodily cavity. It was discovered that objective tissue is able to react to singles types of shots in all spectrum results namely simple smooth penetration wound as well as splintery fracture in dependence on kind of using ammunition. Pork hind-limb was evaluated like the most suitable biological material for given object.

An automated approach to design of solid rockets utilizing a special internal ballistics model

NASA Technical Reports Server (NTRS)

Sforzini, R. H.

1980-01-01

A pattern search technique is presented, which is utilized in a computer program that minimizes the sum of the squares of the differences, at various times, between a desired thrust-time trace and that calculated with a special mathematical internal ballistics model of a solid propellant rocket motor. The program is demonstrated by matching the thrust-time trace obtained from static tests of the first Space Shuttle SRM starting with input values of 10 variables which are, in general, 10% different from the as-built SRM. It is concluded that an excellent match is obtained.

Mechanical properties of silicone based composites as a temperature insensitive ballistic backing material for quantifying back face deformation.

PubMed

Edwards, Tara D; Bain, Erich D; Cole, Shawn T; Freeney, Reygan M; Halls, Virginia A; Ivancik, Juliana; Lenhart, Joseph L; Napadensky, Eugene; Yu, Jian H; Zheng, James Q; Mrozek, Randy A

2018-04-01

This paper describes a new witness material for quantifying the back face deformation (BFD) resulting from high rate impact of ballistic protective equipment. Accurate BFD quantification is critical for the assessment and certification of personal protective equipment, such as body armor and helmets, and ballistic evaluation. A common witness material is ballistic clay, specifically, Roma Plastilina No. 1 (RP1). RP1 must be heated to nearly 38°C to pass calibration, and used within a limited time frame to remain in calibration. RP1 also exhibits lot-to-lot variability and is sensitive to time, temperature, and handling procedures, which limits the BFD accuracy and reproducibility. A new silicone composite backing material (SCBM) was developed and tested side-by-side with heated RP1 using quasi-static indentation and compression, low velocity impact, spherical projectile penetration, and both soft and hard armor ballistic BFD measurements to compare their response over a broad range of strain rates and temperatures. The results demonstrate that SCBM mimics the heated RP1 response at room temperature and exhibits minimal temperature sensitivity. With additional optimization of the composition and processing, SCBM could be a drop-in replacement for RP1 that is used at room temperature during BFD quantification with minimal changes to the current RP1 handling protocols and infrastructure. It is anticipated that removing the heating requirement, and temperature-dependence, associated with RP1 will reduce test variability, simplify testing logistics, and enhance test range productivity. Published by Elsevier B.V.

Ballistic and snake photon imaging for locating optical endomicroscopy fibres

PubMed Central

Tanner, M. G.; Choudhary, T. R.; Craven, T. H.; Mills, B.; Bradley, M.; Henderson, R. K.; Dhaliwal, K.; Thomson, R. R.

2017-01-01

We demonstrate determination of the location of the distal-end of a fibre-optic device deep in tissue through the imaging of ballistic and snake photons using a time resolved single-photon detector array. The fibre was imaged with centimetre resolution, within clinically relevant settings and models. This technique can overcome the limitations imposed by tissue scattering in optically determining the in vivo location of fibre-optic medical instruments. PMID:28966848

Ballistic-diffusive approximation for the thermal dynamics of metallic nanoparticles in nanocomposite materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shirdel-Havar, A. H., E-mail: Amir.hushang.shirdel@gmail.com; Masoudian Saadabad, R.

2015-03-21

Based on ballistic-diffusive approximation, a method is presented to model heat transfer in nanocomposites containing metal nanoparticles. This method provides analytical expression for the temperature dynamics of metallic nanoparticles embedded in a dielectric medium. In this study, nanoparticles are considered as spherical shells, so that Boltzmann equation is solved using ballistic-diffusive approximation to calculate the electron and lattice thermal dynamics in gold nanoparticles, while thermal exchange between the particles is taken into account. The model was used to investigate the influence of particle size and metal concentration of the medium on the electron and lattice thermal dynamics. It is shownmore » that these two parameters are crucial in determining the nanocomposite thermal behavior. Our results showed that the heat transfer rate from nanoparticles to the matrix decreases as the nanoparticle size increases. On the other hand, increasing the metal concentration of the medium can also decrease the heat transfer rate.« less

RBSPICE in the Classroom: Building a ballistic galvanometer using common household products

NASA Astrophysics Data System (ADS)

Patterson, J. D.; Manweiler, J. W.; Lanzerotti, L. J.; Zwiener, H.

2016-12-01

"RBSPICE in the Classroom: Changing Magnetic Fields and Electrical Currents" is a hands-on exercise for middle school and high school science classrooms. Students build a ballistic galvanometer using inexpensive common items that can be purchased at any craft store, and make qualitative observations of changing magnetic fields and the electrical currents they create. The goal of this work is to provide teachers new materials to use in their classrooms as tools for teaching students about electricity and magnetism. The experiment relates our Earth as a planet to the role the Magnetosphere plays in protecting us from Space Weather. The experiments show the ways in which Van Allen Probes play an important part in exploring those relationships using such instruments as the Radiation Belt Storm Probes Ion Composition Experiment (RBSPICE). The exercise is a vehicle for discussing electromagnetic induction, the behavior of the Earth's magnetosphere coupled with storm-time conditions that produce the Earth's ring current, and the mission objectives of the Van Allen Probes RBSPICE instrument.

Current phase relation from graphs and diagrams and application to thick ferromagnetic Josephson junctions

NASA Astrophysics Data System (ADS)

Margaris, I.; Paltoglou, V.; Flytzanis, N.

2018-05-01

In this work we present a method of representing terms in the current-phase-relation of a ballistic Josephson junction by combinations of diagrams, used in previous work to represent an equivalent of the matching condition determinant of the junction. This is accomplished by the expansion of the logarithm of this determinant in Taylor series and keeping track of surviving terms, i.e. terms that do not annihilate each other. The types of the surviving terms are represented by connected graphs, whose points represent diagrammatic terms of the determinant expansion. Then the theory is applied to obtain approximations of the current-phase relation of relatively thick ballistic ferromagnetic Josephson junctions with non-collinear magnetizations. This demonstrates the versatility of the method in developing approximations schemes and providing physical insight into the nature of contributions to the supercurrent from the available particle excitations in the junction. We also discuss the strong second harmonic contribution to the supercurrent in junctions with three mutually orthogonal magnetization vectors and a weak intermediate ferromagnet.

Ballistic interference in ultraclean suspended monolayer graphene

NASA Astrophysics Data System (ADS)

Schonenberger, Christian; Rickhaus, Peter; Maurand, Romain; Makk, Peter; Hess, Samuel; Tovari, Endre; Weiss, Markus; Liu, Ming-Hao; Richter, Klaus

2014-03-01

We have developed a versatile technology that allows to suspend graphene and complement it with arbitrary bottom and top-gate structures. Using current annealing we demonstrate exceptional high mobililties in monolayer graphene approaching 100 m2/Vs. These suspended devices are ballistic over micrometer length scales and display intriguing interference patterns in the electrical con-ductance when different gate potentials are applied. Specifically we will discuss different types of Fabry-Perot resonances that appear in different gate voltage regimes of ballistic pn devices. We will go beyond our recent publication and also show electric transport measurements in magnetic field, where intriguing features appear in the intermediate field range in between the low-field Klein-tunneling regime and the quantum Hall regime. We observe a large number of non-dispersing states which might be due to so-called snake states confined to the pn interface. We will also discuss first results on electron guiding in ultraclean monolayer graphene. We acknowledge funding from the Swiss NFS and the EC.

A quantum wave based compact modeling approach for the current in ultra-short DG MOSFETs suitable for rapid multi-scale simulations

NASA Astrophysics Data System (ADS)

Hosenfeld, Fabian; Horst, Fabian; Iñíguez, Benjamín; Lime, François; Kloes, Alexander

2017-11-01

Source-to-drain (SD) tunneling decreases the device performance in MOSFETs falling below the 10 nm channel length. Modeling quantum mechanical effects including SD tunneling has gained more importance specially for compact model developers. The non-equilibrium Green's function (NEGF) has become a state-of-the-art method for nano-scaled device simulation in the past years. In the sense of a multi-scale simulation approach it is necessary to bridge the gap between compact models with their fast and efficient calculation of the device current, and numerical device models which consider quantum effects of nano-scaled devices. In this work, an NEGF based analytical model for nano-scaled double-gate (DG) MOSFETs is introduced. The model consists of a closed-form potential solution of a classical compact model and a 1D NEGF formalism for calculating the device current, taking into account quantum mechanical effects. The potential calculation omits the iterative coupling and allows the straightforward current calculation. The model is based on a ballistic NEGF approach whereby backscattering effects are considered as second order effect in a closed-form. The accuracy and scalability of the non-iterative DG MOSFET model is inspected in comparison with numerical NanoMOS TCAD data for various channel lengths. With the help of this model investigations on short-channel and temperature effects are performed.

Bullet fragmentation preceding a contour shot: case study and experimental simulation.

PubMed

Sterzik, V; Kneubuehl, B P; Bohnert, M; Riva, F; Glardon, M

2017-01-01

In medico-legal literature, only a small number of publications deal with lethal injuries caused by shots with modified guns. This might lead to the conclusion that such cases are extremely rare. However, there are cases again and yet again. During the investigation process, the modified gun is of particular importance since it can show an unusual ballistic behaviour. The present paper reports on a suicide of a 60-year-old man, committed with a modified revolver and a lead bullet. The man had a single gunshot wound with entrance at the right temporal bone. Autopsy revealed that the bullet had fragmented into two major parts. The smaller one stood outside the cranial cavity and pushed its way alongside between the cranial bone and scalp to its end position in the left temporal area. The bigger part entered the cranial cavity and ended in the left parietal lobe. In shots on ballistic soap and on a head-model, the ballistics of the weapon and lead bullet were characterized. The angle necessary for bullet fragmentation was determined by shots on ballistic soap and turned out to be 55°-60° at a velocity of around 200 m/s. This knowledge was transferred to contact shots on a head-model consisting of a layered polyurethane sphere filled with 10 % ballistic gelatine and covered with a skin-like cap almost all around. The resulting injury pattern corresponded to the one of the suicide person. The bigger bullet part entered the skull while the smaller part pushed its way alongside between skin and skull causing an outer contour shot. Furthermore, the revolver was documented firing off two bullets by one trigger pull-a phenomenon of importance for forensic casework the authors have not found reported in forensic literature.

Modeling internal ballistics of gas combustion guns.

PubMed

Schorge, Volker; Grossjohann, Rico; Schönekess, Holger C; Herbst, Jörg; Bockholdt, Britta; Ekkernkamp, Axel; Frank, Matthias

2016-05-01

Potato guns are popular homemade guns which work on the principle of gas combustion. They are usually constructed for recreational rather than criminal purposes. Yet some serious injuries and fatalities due to these guns are reported. As information on the internal ballistics of homemade gas combustion-powered guns is scarce, it is the aim of this work to provide an experimental model of the internal ballistics of these devices and to investigate their basic physical parameters. A gas combustion gun was constructed with a steel tube as the main component. Gas/air mixtures of acetylene, hydrogen, and ethylene were used as propellants for discharging a 46-mm caliber test projectile. Gas pressure in the combustion chamber was captured with a piezoelectric pressure sensor. Projectile velocity was measured with a ballistic speed measurement system. The maximum gas pressure, the maximum rate of pressure rise, the time parameters of the pressure curve, and the velocity and path of the projectile through the barrel as a function of time were determined according to the pressure-time curve. The maximum gas pressure was measured to be between 1.4 bar (ethylene) and 4.5 bar (acetylene). The highest maximum rate of pressure rise was determined for hydrogen at (dp/dt)max = 607 bar/s. The muzzle energy was calculated to be between 67 J (ethylene) and 204 J (acetylene). To conclude, this work provides basic information on the internal ballistics of homemade gas combustion guns. The risk of injury to the operator or bystanders is high, because accidental explosions of the gun due to the high-pressure rise during combustion of the gas/air mixture may occur.

Ballistic movements of jumping legs implemented as variable components of cricket behaviour.

PubMed

Hustert, R; Baldus, M

2010-12-01

Ballistic accelerations of a limb or the whole body require special joint mechanisms in many animals. Specialized joints can be moved by stereotypic or variable motor control during motor patterns with and without ballistic components. As a model of variable motor control, the specialized femur-tibia (knee) joints of cricket (Acheta domesticus) hindlegs were studied during ballistic kicking, jumping and swimming and in non-ballistic walking. In this joint the tendons of the antagonistic flexor and the extensor muscles attach at different distances from the pivot and the opposed lever arms form an angle of 120 deg. A 10:1 ratio of their effective lever arms at full knee flexion helps to prepare for most ballistic extensions: the tension of the extensor can reach its peak while it is restrained by flexor co-contraction. In kicks, preparatory flexion is rapid and the co-contraction terminates just before knee extensions. Therefore, mainly the stored tension of the extensor muscle accelerates the small mass of the tibia. Jumps are prepared with slower extensor-flexor co-contractions that flex both knees simultaneously and then halt to rotate both legs outward to a near horizontal level. From there, catapult extension of both knees accelerates the body, supported by continued high frequency motor activity to their tibia extensor muscles during the ongoing push-off from the substrate. Premature extension of one knee instantly takes load from the lagging leg that extends and catches up, which finally results in a straight jump. In swimming, synchronous ballistic power strokes of both hindlegs drive the tibiae on a ventral-to-posterior trajectory through the water, well coordinated with the swimming patterns of all legs. In walking, running and climbing the steps of the hindlegs range between 45 deg flexion and 125 deg extension and use non-ballistic, alternating activity of knee flexor and extensor muscles. Steep climbing requires longer bursts from the extensor tibiae muscles when they support the extended hindlegs against gravity forces when the body hangs over. All ballistic movements of cricket knees are elicited by a basic but variable motor pattern: knee flexions by co-contraction of the antagonists prepare catapult extensions with speeds and forces as required in the different behaviours.

An investigation into the relationship between thermal shock resistance and ballistic performance of ceramic materials

NASA Astrophysics Data System (ADS)

Beaumont, Robert

Currently, there are no reliable methods for screening potential armour materials and hence full-scale ballistic trials are needed. These are both costly and time-consuming in terms of the actual test and also in the materials development that needs to take place to produce sufficient material to give a meaningful result. Whilst it will not be possible to dispense with ballistic trials before material deployment in armour applications, the ability to shorten the development cycle would be advantageous. The thermal shock performance of ceramic armour materials has been highlighted as potential marker for ballistic performance. Hence the purpose of this study was to investigate this further. A new thermal shock technique that reproduced features relevant to ballistic testing was sought. As it would be beneficial to have a simple test that did not use much material, a water-drop method was adopted. This was combined with a variety of characterisation techniques, administered pre- and post-shock. The methods included measurement of the amplitude of ultrasonic wave transmission through the sample alongside residual strength testing using a biaxial ball-on-ball configuration and reflected light and confocal microscopy. Once the protocols had been refined the testing regime was applied to a group of ceramic materials. The materials selected were from two broad groups: alumina and carbide materials. Carbide ceramics show superior performance to alumina ceramics in ballistic applications so it was essential that any screening test would be easily able to differentiate the two groups. Within the alumina family, two commercially available materials, AD995 and Sintox FA, were selected. These were tested alongside three developmental silicon carbide-boron carbide composites, which had identical chemical compositions but different microstructures and thus presented more of a challenge in terms of differentiation. The results from the various tests were used to make predictions about the relative ballistic performances. The tests showed that all of the composites would outperform the alumina materials. Further, all of the tests led to the prediction that AD995 would be better ballistically than Sintox FA, possibly up to a factor of two better. The predictions were in very good agreement with literature values for depth-of-penetration testing. The situation was more complex for the carbide materials, with different tests leading to slightly different predictions. However, the predictions from the ultrasonic tests were consistent with the available ballistic data. Indeed, the ultrasonic data proved to be the most consistent predictor of ballistic performance, supporting the view that the total defect population is more relevant than a ‘critical flaw’ concept. Thus, it can be concluded that with further development, and subject to validation across a wider spread of materials and microstructures, thermal shock testing coupled with ultrasonic measurements could form the basis of a future screening test for ceramics for armour applications.

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems. Part 2; Ballistic Impact Testing

NASA Technical Reports Server (NTRS)

Pereira, J. M.; Revilock, D. M.

2004-01-01

Under the Federal Aviation Administration's Airworthiness Assurance Center of Excellence and the Aircraft Catastrophic Failure Prevention Program, National Aeronautics and Space Administration Glenn Research Center collaborated with Arizona State University, Honeywell Engines, Systems and Services, and SRI International to develop improved computational models for designing fabric-based engine containment systems. In the study described in this report, ballistic impact tests were conducted on layered dry fabric rings to provide impact response data for calibrating and verifying the improved numerical models. This report provides data on projectile velocity, impact and residual energy, and fabric deformation for a number of different test conditions.

Body models in forensic ballistics: reconstruction of a gunshot injury to the chest by bullet fragmentation after shooting through a finger.

PubMed

Thali, M J; Kneubuehl, B P; Dirnhofer, R; Zollinger, U

2001-11-15

Forensic science uses substitutes to reconstruct injury patterns in order to answer questions regarding the dynamic formation of unusual injuries. Using a case study, an experimental simulation of a finger was designed, for the first time with a combination of hard wood and glycerin soap. With this model as an intermediate target simulation, it was possible not only to demonstrate the "bullet-body (finger) interaction", but also to recreate the wound pattern found in the victim. This case demonstrates that by using ballistic models and body-part substitutes, gunshot cases can be reproduced simply and economically, without coming into conflict with ethical guidelines.

Forensic reconstruction of two military combat related shooting incidents using an anatomically correct synthetic skull with a surrogate skin/soft tissue layer.

PubMed

Mahoney, Peter; Carr, Debra; Harrison, Karl; McGuire, Ruth; Hepper, Alan; Flynn, Daniel; Delaney, Russ J; Gibb, Iain

2018-03-07

Six synthetic head models wearing ballistic protective helmets were used to recreate two military combat-related shooting incidents (three per incident, designated 'Incident 1' and 'Incident 2'). Data on the events including engagement distances, weapon and ammunition types was collated by the Defence Science and Technology Laboratory. The models were shot with 7.62 × 39 mm ammunition downloaded to mean impact velocities of 581 m/s (SD 3.5 m/s) and 418 m/s (SD 8 m/s), respectively, to simulate the engagement distances. The damage to the models was assessed using CT imaging and dissection by a forensic pathologist experienced in reviewing military gunshot wounds. The helmets were examined by an MoD engineer experienced in ballistic incident analysis. Damage to the helmets was consistent with that seen in real incidents. Fracture patterns and CT imaging on two of the models for Incident 1 (a frontal impact) were congruent with the actual incident being modelled. The results for Incident 2 (a temporoparietal impact) produced realistic simulations of tangential gunshot injury but were less representative of the scenario being modelled. Other aspects of the wounds produced also exhibited differences. Further work is ongoing to develop the models for greater ballistic injury fidelity.

Evidence of Momentum Conservation at a Nonepitaxial Metal/Semiconductor Interface Using Ballistic Electron Emission Microscopy

NASA Technical Reports Server (NTRS)

Bell, L. D.

1996-01-01

Ballistic-Electron-Emission Microscopy (BEEM) spectroscopy has been performed on Au/Si(111) structures as a function of Au thickness and temperature. At 77 K a direct signature of parallel momentum conservation at the Au/Si interface is observed in the BEEM spectra. The variation in spectral shape with both Au thickness and temperature places restrictions on allowable values of inelastic and elastic mean-free paths in the metal, and also requires the presence of multiple electron passes within the Au layer. An independent indication of multiple reflections is directly observed in the attenuation of BEEM current with Au thickness.

Gate tuneable beamsplitter in ballistic graphene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rickhaus, Peter; Makk, Péter, E-mail: Peter.Makk@unibas.ch; Schönenberger, Christian

2015-12-21

We present a beam splitter in a suspended, ballistic, multiterminal, bilayer graphene device. By using local bottomgates, a p-n interface tilted with respect to the current direction can be formed. We show that the p-n interface acts as a semi-transparent mirror in the bipolar regime and that the reflectance and transmittance of the p-n interface can be tuned by the gate voltages. Moreover, by studying the conductance features appearing in magnetic field, we demonstrate that the position of the p-n interface can be moved by 1 μm. The herein presented beamsplitter device can form the basis of electron-optic interferometers in graphene.

Development and evaluation of a musculoskeletal model of the elbow joint complex

NASA Technical Reports Server (NTRS)

Gonzalez, Roger V.; Hutchins, E. L.; Barr, Ronald E.; Abraham, Lawrence D.

1993-01-01

This paper describes the development and evaluation of a musculoskeletal model that represents human elbow flexion-extension and forearm pronation-supination. The length, velocity, and moment arm for each of the eight musculotendon actuators were based on skeletal anatomy and position. Musculotendon parameters were determined for each actuator and verified by comparing analytical torque-angle curves with experimental joint torque data. The parameters and skeletal geometry were also utilized in the musculoskeletal model for the analysis of ballistic elbow joint complex movements. The key objective was to develop a computational model, guided by parameterized optimal control, to investigate the relationship among patterns of muscle excitation, individual muscle forces, and movement kinematics. The model was verified using experimental kinematic, torque, and electromyographic data from volunteer subjects performing ballistic elbow joint complex movements.

Ballistics for the neurosurgeon.

PubMed

Jandial, Rahul; Reichwage, Brett; Levy, Michael; Duenas, Vincent; Sturdivan, Larry

2008-02-01

Craniocerebral injuries from ballistic projectiles are qualitatively different from injuries in unconfined soft tissue with similar impact. Penetrating and nonpenetrating ballistic injuries are influenced not only by the physical properties of the projectile, but also by its ballistics. Ballistics provides information on the motion of projectiles while in the gun barrel, the trajectory of the projectile in air, and the behavior of the projectile on reaching its target. This basic knowledge can be applied to better understand the ultimate craniocerebral consequences of ballistic head injuries.

Quasi-ballistic carbon nanotube array transistors with current density exceeding Si and GaAs

PubMed Central

Brady, Gerald J.; Way, Austin J.; Safron, Nathaniel S.; Evensen, Harold T.; Gopalan, Padma; Arnold, Michael S.

2016-01-01

Carbon nanotubes (CNTs) are tantalizing candidates for semiconductor electronics because of their exceptional charge transport properties and one-dimensional electrostatics. Ballistic transport approaching the quantum conductance limit of 2G0 = 4e2/h has been achieved in field-effect transistors (FETs) containing one CNT. However, constraints in CNT sorting, processing, alignment, and contacts give rise to nonidealities when CNTs are implemented in densely packed parallel arrays such as those needed for technology, resulting in a conductance per CNT far from 2G0. The consequence has been that, whereas CNTs are ultimately expected to yield FETs that are more conductive than conventional semiconductors, CNTs, instead, have underperformed channel materials, such as Si, by sixfold or more. We report quasi-ballistic CNT array FETs at a density of 47 CNTs μm−1, fabricated through a combination of CNT purification, solution-based assembly, and CNT treatment. The conductance is as high as 0.46 G0 per CNT. In parallel, the conductance of the arrays reaches 1.7 mS μm−1, which is seven times higher than the previous state-of-the-art CNT array FETs made by other methods. The saturated on-state current density is as high as 900 μA μm−1 and is similar to or exceeds that of Si FETs when compared at and equivalent gate oxide thickness and at the same off-state current density. The on-state current density exceeds that of GaAs FETs as well. This breakthrough in CNT array performance is a critical advance toward the exploitation of CNTs in logic, high-speed communications, and other semiconductor electronics technologies. PMID:27617293

Quasi-ballistic carbon nanotube array transistors with current density exceeding Si and GaAs.

PubMed

Brady, Gerald J; Way, Austin J; Safron, Nathaniel S; Evensen, Harold T; Gopalan, Padma; Arnold, Michael S

2016-09-01

Carbon nanotubes (CNTs) are tantalizing candidates for semiconductor electronics because of their exceptional charge transport properties and one-dimensional electrostatics. Ballistic transport approaching the quantum conductance limit of 2G 0 = 4e (2)/h has been achieved in field-effect transistors (FETs) containing one CNT. However, constraints in CNT sorting, processing, alignment, and contacts give rise to nonidealities when CNTs are implemented in densely packed parallel arrays such as those needed for technology, resulting in a conductance per CNT far from 2G 0. The consequence has been that, whereas CNTs are ultimately expected to yield FETs that are more conductive than conventional semiconductors, CNTs, instead, have underperformed channel materials, such as Si, by sixfold or more. We report quasi-ballistic CNT array FETs at a density of 47 CNTs μm(-1), fabricated through a combination of CNT purification, solution-based assembly, and CNT treatment. The conductance is as high as 0.46 G 0 per CNT. In parallel, the conductance of the arrays reaches 1.7 mS μm(-1), which is seven times higher than the previous state-of-the-art CNT array FETs made by other methods. The saturated on-state current density is as high as 900 μA μm(-1) and is similar to or exceeds that of Si FETs when compared at and equivalent gate oxide thickness and at the same off-state current density. The on-state current density exceeds that of GaAs FETs as well. This breakthrough in CNT array performance is a critical advance toward the exploitation of CNTs in logic, high-speed communications, and other semiconductor electronics technologies.

Analysis of behind the armor ballistic trauma.

PubMed

Wen, Yaoke; Xu, Cheng; Wang, Shu; Batra, R C

2015-05-01

The impact response of body armor composed of a ceramic plate with an ultrahigh molecular weight polyethylene (UHMWPE) fiber-reinforced composite and layers of UHMWPE fibers shielding a block of ballistic gelatin has been experimentally and numerically analyzed. It is a surrogate model for studying injuries to human torso caused by a bullet striking body protection armor placed on a person. Photographs taken with a high speed camera are used to determine deformations of the armor and the gelatin. The maximum depth of the temporary cavity formed in the ballistic gelatin and the peak pressure 40mm behind the center of the gelatin front face contacting the armor are found to be, respectively, ~34mm and ~15MPa. The Johnson-Holmquist material model has been used to simulate deformations and failure of the ceramic. The UHMWPE fiber-reinforced composite and the UHMWPE fiber layers are modeled as linear elastic orthotropic materials. The gelatin is modeled as a strain-rate dependent hyperelastic material. Values of material parameters are taken from the open literature. The computed evolution of the temporary cavity formed in the gelatin is found to qualitatively agree with that seen in experiments. Furthermore, the computed time histories of the average pressure at four points in the gelatin agree with the corresponding experimentally measured ones. The maximum pressure at a point and the depth of the temporary cavity formed in the gelatin can be taken as measures of the severity of the bodily injury caused by the impact; e.g. see the United States National Institute of Justice standard 0101.06-Ballistic Resistance of Body Armor. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ballistic projectile trajectory determining system

DOEpatents

Karr, Thomas J.

1997-01-01

A computer controlled system determines the three-dimensional trajectory of a ballistic projectile. To initialize the system, predictions of state parameters for a ballistic projectile are received at an estimator. The estimator uses the predictions of the state parameters to estimate first trajectory characteristics of the ballistic projectile. A single stationary monocular sensor then observes the actual first trajectory characteristics of the ballistic projectile. A comparator generates an error value related to the predicted state parameters by comparing the estimated first trajectory characteristics of the ballistic projectile with the observed first trajectory characteristics of the ballistic projectile. If the error value is equal to or greater than a selected limit, the predictions of the state parameters are adjusted. New estimates for the trajectory characteristics of the ballistic projectile are made and are then compared with actual observed trajectory characteristics. This process is repeated until the error value is less than the selected limit. Once the error value is less than the selected limit, a calculator calculates trajectory characteristics such a the origin and destination of the ballistic projectile.

Orbital Debris Shape and Orientation Effects on Ballistic Limits

NASA Technical Reports Server (NTRS)

Evans, Steven W.; Williamsen, Joel E.

2005-01-01

The SPHC hydrodynamic code was used to evaluate the effects of orbital debris particle shape and orientation on penetration of a typical spacecraft dual-wall shield. Impacts were simulated at near-normal obliquity at 12 km/sec. Debris cloud characteristics and damage potential are compared with those from impacts by spherical projectiles. Results of these simulations indicate the uncertainties in the predicted ballistic limits due to modeling uncertainty and to uncertainty in the impactor orientation.

Direct determination of energy level alignment and charge transport at metal-Alq3 interfaces via ballistic-electron-emission spectroscopy.

PubMed

Jiang, J S; Pearson, J E; Bader, S D

2011-04-15

Using ballistic-electron-emission spectroscopy (BEES), we directly determined the energy barrier for electron injection at clean interfaces of Alq(3) with Al and Fe to be 2.1 and 2.2 eV, respectively. We quantitatively modeled the sub-barrier BEES spectra with an accumulated space charge layer, and found that the transport of nonballistic electrons is consistent with random hopping over the injection barrier.

Axial-Compressive Behavior, Including Kink-Band Formation and Propagation, of Single p-Phenylene Terephthalamide (PPTA) Fibers

DTIC Science & Technology

2013-01-01

material models to describe the behavior of fibers and structures under high -rate loading conditions. With the utility of the CAE methods and tools largely...phenylene terephthalamide (PPTA), available commercially as Kevlar, Twaron, Technora, and so forth, are characterized by high specific axial stiffness...and high specific tensile strength. These fibers are often referred to as “ballistic fibers” since they are commonly used in different ballistic- and

Direct determination of energy level alignment and charge transport at metal/Alq{sub 3} interfaces via ballistic-electron-emission spectroscopy.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, J. S.; Pearson, J. E.; Bader, S. D.

2011-04-15

Using ballistic-electron-emission spectroscopy (BEES), we directly determined the energy barrier for electron injection at clean interfaces of Alq{sub 3} with Al and Fe to be 2.1 and 2.2 eV, respectively. We quantitatively modeled the sub-barrier BEES spectra with an accumulated space charge layer, and found that the transport of nonballistic electrons is consistent with random hopping over the injection barrier.

Electrothermal-Chemical Modeling and Diagnostics Workshop. Volume 1

DTIC Science & Technology

1991-10-01

z ox IOX OLVox 110~ Table 2: Summary of the theorctical rcsuilts (J Powell and Zielinski (ideal plasma) Shot VTr T P.’ 4 Volts (cV) (.Pa) (. m) 2 1221...Gloria P. Wren Ballistic Research Laboratory ATTN: SLCBR-IB-B Aberdeen Proving Ground, MD 21005-5066 (301) 278-6199 Mr. Alex Zielinski Ballistic Research...Park Road, SE Warren, MI 48090-2074 Albuquerque, NM 87106 General Dynamics Land Systems Division 1 Teledyne Brown Engineering ATTN: Dave Toepler ATTN

Principles of ballistics applicable to the treatment of gunshot wounds.

PubMed

Swan, K G; Swan, R C

1991-04-01

Ballistics is the science of the motion of a projectile through the barrel of a firearm (internal ballistics), during its subsequent flight (external ballistics), and during its final complicated motion after it strikes a target (terminal ballistics). Wound ballistics is a special case of terminal ballistics. Although wound ballistics is at best sets of approximations, its principles enter usefully into an evaluation of a gunshot wound and its treatment. A special consideration in these cases is their medicolegal aspects. At a minimum, the medical team receiving the patient should exert care not to destroy the clothing and in particular to cut around and not through bullet holes, to turn over to law enforcement officials any metallic foreign body recovered from the patient, and to describe precisely, or even to photograph, any entrance or exit wounds.

Emergent transport in a many-body open system driven by interacting quantum baths

NASA Astrophysics Data System (ADS)

Reisons, Juris; Mascarenhas, Eduardo; Savona, Vincenzo

2017-10-01

We analyze an open many-body system that is strongly coupled at its boundaries to interacting quantum baths. We show that the two-body interactions inside the baths induce emergent phenomena in the spin transport. The system and baths are modeled as independent spin chains resulting in a global nonhomogeneous X X Z model. The evolution of the system-bath state is simulated using matrix-product-states methods. We present two phase transitions induced by bath interactions. For weak bath interactions we observe ballistic and insulating phases. However, for strong bath interactions a diffusive phase emerges with a distinct power-law decay of the time-dependent spin current Q ∝t-α . Furthermore, we investigate long-lasting current oscillations arising from the non-Markovian dynamics in the homogeneous case and find a sharp change in their frequency scaling coinciding with the triple point of the phase diagram.

Terahertz Detection and Imaging Using Graphene Ballistic Rectifiers.

PubMed

Auton, Gregory; But, Dmytro B; Zhang, Jiawei; Hill, Ernie; Coquillat, Dominique; Consejo, Christophe; Nouvel, Philippe; Knap, Wojciech; Varani, Luca; Teppe, Frederic; Torres, Jeremie; Song, Aimin

2017-11-08

A graphene ballistic rectifier is used in conjunction with an antenna to demonstrate a rectenna as a terahertz (THz) detector. A small-area (<1 μm 2 ) local gate is used to adjust the Fermi level in the device to optimize the output while minimizing the impact on the cutoff frequency. The device operates in both n- and p-type transport regimes and shows a peak extrinsic responsivity of 764 V/W and a corresponding noise equivalent power of 34 pW Hz -1/2 at room temperature with no indications of a cutoff frequency up to 0.45 THz. The device also demonstrates a linear response for more than 3 orders of magnitude of input power due to its zero threshold voltage, quadratic current-voltage characteristics and high saturation current. Finally, the device is used to take an image of an optically opaque object at 0.685 THz, demonstrating potential in both medical and security imaging applications.

Ultimately short ballistic vertical graphene Josephson junctions

PubMed Central

Lee, Gil-Ho; Kim, Sol; Jhi, Seung-Hoon; Lee, Hu-Jong

2015-01-01

Much efforts have been made for the realization of hybrid Josephson junctions incorporating various materials for the fundamental studies of exotic physical phenomena as well as the applications to superconducting quantum devices. Nonetheless, the efforts have been hindered by the diffusive nature of the conducting channels and interfaces. To overcome the obstacles, we vertically sandwiched a cleaved graphene monoatomic layer as the normal-conducting spacer between superconducting electrodes. The atomically thin single-crystalline graphene layer serves as an ultimately short conducting channel, with highly transparent interfaces with superconductors. In particular, we show the strong Josephson coupling reaching the theoretical limit, the convex-shaped temperature dependence of the Josephson critical current and the exceptionally skewed phase dependence of the Josephson current; all demonstrate the bona fide short and ballistic Josephson nature. This vertical stacking scheme for extremely thin transparent spacers would open a new pathway for exploring the exotic coherence phenomena occurring on an atomic scale. PMID:25635386

Hydrodynamic pumping of a quantum Fermi liquid in a semiconductor heterostructure

NASA Astrophysics Data System (ADS)

Heremans, J. J.; Kantha, D.; Chen, H.; Govorov, A. O.

2003-03-01

We present experimental results for a pumping mechanism observed in mesoscopic structures patterned on two-dimensional electron systems in GaAs/AlGaAs heterostructures. The experiments are performed at low temperatures, in the ballistic regime. The effect is observed as a voltage or current signal corresponding to carrier extraction from sub-micron sized apertures, when these apertures are swept by a beam of ballistic electrons. The carrier extraction, phenomenologically reminiscent of the Bernoulli pumping effect in classical fluids, has been observed in various geometries. We ascertained linearity between measured voltage and injected current in all experiments, thereby excluding rectification effects. The linear response, however, points to a fundamental difference from the Bernoulli effect in classical liquids, where the response is nonlinear and quadratic in terms of the velocity. The temperature dependence of the effect will also be presented. We thank M. Shayegan (Princeton University) for the heterostructure growth, and acknowledge support from NSF DMR-0094055.

The reference cube: A new ballistic model to generate staining in firearm barrels.

PubMed

Schyma, Christian; Bauer, Kristina; Brünig, Julia

2017-06-01

After contact shots to the head biological traces can be found inside firearm barrels. So far silicone coated, gelatin filled box models were used to generate such staining according to the triple contrast method (mixture of acrylic paint, barium sulfate and blood sealed in a thin foil bag). This study was conducted to develop a transparent ballistic model allowing contact shots. Gelatin filled polyethylene bottles with and without a silicone coat were tested in comparison to non-covered gelatin blocks. Finally, thin foil bags of 5 cm × 5 cm dimension were glued on a synthetic absorbent kitchen wipe on top of which 1 L 10% gelatin solution was molded to create blocks of 8.5 cm length. A kitchen wipe with a paint pad on its inside formed the front of the cube. Three contact shots each with a 9 mm Luger pistol and a .38 special revolver were performed on all model variations. The staining was documented by endoscopy and swabs gathered from both ends of the barrel were analyzed by quantitative PCR. Reliable staining was achieved using the front covered gelatin block with comparable results to the silicone coated box model used before. For further research using ballistic models to simulate a human head a symmetric form of the gelatin block such as a cube is recommended.

Medical Provider Ballistic Protection at Active Shooter Events.

PubMed

Stopyra, Jason P; Bozeman, William P; Callaway, David W; Winslow, James; McGinnis, Henderson D; Sempsrott, Justin; Evans-Taylor, Lisa; Alson, Roy L

2016-01-01

There is some controversy about whether ballistic protective equipment (body armor) is required for medical responders who may be called to respond to active shooter mass casualty incidents. In this article, we describe the ongoing evolution of recommendations to optimize medical care to injured victims at such an incident. We propose that body armor is not mandatory for medical responders participating in a rapid-response capacity, in keeping with the Hartford Consensus and Arlington Rescue Task Force models. However, we acknowledge that the development and implementation of these programs may benefit from the availability of such equipment as one component of risk mitigation. Many police agencies regularly retire body armor on a defined time schedule before the end of its effective service life. Coordination with law enforcement may allow such retired body armor to be available to other public safety agencies, such as fire and emergency medical services, providing some degree of ballistic protection to medical responders at little or no cost during the rare mass casualty incident. To provide visual demonstration of this concept, we tested three "retired" ballistic vests with ages ranging from 6 to 27 years. The vests were shot at close range using police-issue 9mm, .40 caliber, .45 caliber, and 12-gauge shotgun rounds. Photographs demonstrate that the vests maintained their ballistic protection and defeated all of these rounds. 2016.

Determine ISS Soyuz Orbital Module Ballistic Limits for Steel Projectiles Hypervelocity Impact Testing

NASA Technical Reports Server (NTRS)

Lyons, Frankel

2013-01-01

A new orbital debris environment model (ORDEM 3.0) defines the density distribution of the debris environment in terms of the fraction of debris that are low-density (plastic), medium-density (aluminum) or high-density (steel) particles. This hypervelocity impact (HVI) program focused on assessing ballistic limits (BLs) for steel projectiles impacting the enhanced Soyuz Orbital Module (OM) micrometeoroid and orbital debris (MMOD) shield configuration. The ballistic limit was defined as the projectile size on the threshold of failure of the OM pressure shell as a function of impact speeds and angle. The enhanced OM shield configuration was first introduced with Soyuz 30S (launched in May 2012) to improve the MMOD protection of Soyuz vehicles docked to the International Space Station (ISS). This test program provides HVI data on U.S. materials similar in composition and density to the Russian materials for the enhanced Soyuz OM shield configuration of the vehicle. Data from this test program was used to update ballistic limit equations used in Soyuz OM penetration risk assessments. The objective of this hypervelocity impact test program was to determine the ballistic limit particle size for 440C stainless steel spherical projectiles on the Soyuz OM shielding at several impact conditions (velocity and angle combinations). This test report was prepared by NASA-JSC/ HVIT, upon completion of tests.

The Effect of Ballistic Impacts on the High Cycle Fatigue Properties of Ti-48Al-2Nb-2Cr (at.%)

NASA Technical Reports Server (NTRS)

Draper, S. L.; Lerch, B. A.; Pereira, J. M.; Nathal, M. V.; Austin, C. M.; Erdman, O.

2000-01-01

The ability of gamma - TiAl to withstand potential foreign and/or domestic object damage is a technical risk to the implementation of gamma - TiAl in low pressure turbine (LPT) blade applications. The overall purpose of the present study was to determine the influence of ballistic impact damage on the high cycle fatigue strength of gamma - TiAl simulated LPT blades. Impact and specimen variables included ballistic impact energy, projectile hardness, impact temperature, impact location, and leading edge thickness. The level of damage induced by the ballistic impacting was studied and quantified on both the impact (front) and backside of the specimens. Multiple linear regression was used to model the cracking and fatigue response as a function of the impact variables. Of the impact variables studied, impact energy had the largest influence on the response of gamma - TiAl to ballistic impacting. Backside crack length was the best predictor of remnant fatigue strength for low energy impacts (<0.74J) whereas Hertzian crack length (impact side damage) was the best predictor for higher energy impacts. The impacted gamma - TiAl samples displayed a classical mean stress dependence on the fatigue strength. For the fatigue design stresses of a 6th stage LPT blade in a GE90 engine, a Ti-48Al-2Nb-2Cr LPT blade would survive an impact of normal service conditions.

10. Storage and shipping container, ballistic missile, mounted on ballistic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Storage and shipping container, ballistic missile, mounted on ballistic missile trailer, view from left front - Ellsworth Air Force Base, Delta Flight, 10 mile radius around Exit 127 off Interstate 90, Interior, Jackson County, SD

11. Storage and shipping container, ballistic missile, mounted on ballistic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Storage and shipping container, ballistic missile, mounted on ballistic missile trailer, view from left side - Ellsworth Air Force Base, Delta Flight, 10 mile radius around Exit 127 off Interstate 90, Interior, Jackson County, SD

Uncertainty Considerations for Ballistic Limit Equations

NASA Technical Reports Server (NTRS)

Schonberg, W. P.; Evans, H. J.; Williamsen, J. E.; Boyer, R. L.; Nakayama, G. S.

2005-01-01

The overall risk for any spacecraft system is typically determined using a Probabilistic Risk Assessment (PRA). A PRA attempts to determine the overall risk associated with a particular mission by factoring in all known risks (and their corresponding uncertainties, if known) to the spacecraft during its mission. The threat to mission and human life posed by the mircro-meteoroid & orbital debris (MMOD) environment is one of the risks. NASA uses the BUMPER II program to provide point estimate predictions of MMOD risk for the Space Shuttle and the International Space Station. However, BUMPER II does not provide uncertainty bounds or confidence intervals for its predictions. With so many uncertainties believed to be present in the models used within BUMPER II, providing uncertainty bounds with BUMPER II results would appear to be essential to properly evaluating its predictions of MMOD risk. The uncertainties in BUMPER II come primarily from three areas: damage prediction/ballistic limit equations, environment models, and failure criteria definitions. In order to quantify the overall uncertainty bounds on MMOD risk predictions, the uncertainties in these three areas must be identified. In this paper, possible approaches through which uncertainty bounds can be developed for the various damage prediction and ballistic limit equations encoded within the shuttle and station versions of BUMPER II are presented and discussed. We begin the paper with a review of the current approaches used by NASA to perform a PRA for the Space Shuttle and the International Space Station, followed by a review of the results of a recent sensitivity analysis performed by NASA using the shuttle version of the BUMPER II code. Following a discussion of the various equations that are encoded in BUMPER II, we propose several possible approaches for establishing uncertainty bounds for the equations within BUMPER II. We conclude with an evaluation of these approaches and present a recommendation regarding which of them would be the most appropriate to follow.

Explicit densities of multidimensional ballistic Lévy walks.

PubMed

Magdziarz, Marcin; Zorawik, Tomasz

2016-08-01

Lévy walks have proved to be useful models of stochastic dynamics with a number of applications in the modeling of real-life phenomena. In this paper we derive explicit formulas for densities of the two- (2D) and three-dimensional (3D) ballistic Lévy walks, which are most important in applications. It turns out that in the 3D case the densities are given by elementary functions. The densities of the 2D Lévy walks are expressed in terms of hypergeometric functions and the right-side Riemann-Liouville fractional derivative, which allows us to efficiently evaluate them numerically. The theoretical results agree perfectly with Monte Carlo simulations.

59. View of high voltage (4160 volts alternating current) electric ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

59. View of high voltage (4160 volts alternating current) electric load center and motor control center at mezzanine level in transmitter building no. 102. - Clear Air Force Station, Ballistic Missile Early Warning System Site II, One mile west of mile marker 293.5 on Parks Highway, 5 miles southwest of Anderson, Anderson, Denali Borough, AK

Transverse-Weld Tensile Properties of a New Al-4Cu-2Si Alloy as Filler Metal

NASA Astrophysics Data System (ADS)

Sampath, K.

2009-12-01

AA2195, an Al-Cu-Li alloy in the T8P4 age-hardened condition, is a candidate aluminum armor for future combat vehicles, as this material offers higher static strength and ballistic protection than current aluminum armor alloys. However, certification of AA2195 alloy for armor applications requires initial qualification based on the ballistic performance of welded panels in the as-welded condition. Currently, combat vehicle manufacturers primarily use gas metal arc welding (GMAW) process to meet their fabrication needs. Unfortunately, a matching GMAW consumable electrode is currently not commercially available to allow effective joining of AA2195 alloy. This initial effort focused on an innovative, low-cost, low-risk approach to identify an alloy composition suitable for effective joining of AA2195 alloy, and evaluated transverse-weld tensile properties of groove butt joints produced using the identified alloy. Selected commercial off-the-shelf (COTS) aluminum alloy filler wires were twisted to form candidate twisted filler rods. Representative test weldments were produced using AA2195 alloy, candidate twisted filler rods and gas tungsten arc welding (GTAW) process. Selected GTA weldments produced using Al-4wt.%Cu-2wt.%Si alloy as filler metal consistently provided transverse-weld tensile properties in excess of 275 MPa (40 ksi) UTS and 8% El (over 25 mm gage length), thereby showing potential for acceptable ballistic performance of as-welded panels. Further developmental work is required to evaluate in detail GMAW consumable wire electrodes based on the Al-Cu-Si system containing 4.2-5.0 wt.% Cu and 1.6-2.0 wt.% Si.

Aging ballistic Lévy walks

NASA Astrophysics Data System (ADS)

Magdziarz, Marcin; Zorawik, Tomasz

2017-02-01

Aging can be observed for numerous physical systems. In such systems statistical properties [like probability distribution, mean square displacement (MSD), first-passage time] depend on a time span ta between the initialization and the beginning of observations. In this paper we study aging properties of ballistic Lévy walks and two closely related jump models: wait-first and jump-first. We calculate explicitly their probability distributions and MSDs. It turns out that despite similarities these models react very differently to the delay ta. Aging weakly affects the shape of probability density function and MSD of standard Lévy walks. For the jump models the shape of the probability density function is changed drastically. Moreover for the wait-first jump model we observe a different behavior of MSD when ta≪t and ta≫t .

Ballistic projectile trajectory determining system

DOEpatents

Karr, T.J.

1997-05-20

A computer controlled system determines the three-dimensional trajectory of a ballistic projectile. To initialize the system, predictions of state parameters for a ballistic projectile are received at an estimator. The estimator uses the predictions of the state parameters to estimate first trajectory characteristics of the ballistic projectile. A single stationary monocular sensor then observes the actual first trajectory characteristics of the ballistic projectile. A comparator generates an error value related to the predicted state parameters by comparing the estimated first trajectory characteristics of the ballistic projectile with the observed first trajectory characteristics of the ballistic projectile. If the error value is equal to or greater than a selected limit, the predictions of the state parameters are adjusted. New estimates for the trajectory characteristics of the ballistic projectile are made and are then compared with actual observed trajectory characteristics. This process is repeated until the error value is less than the selected limit. Once the error value is less than the selected limit, a calculator calculates trajectory characteristics such a the origin and destination of the ballistic projectile. 8 figs.

Ballistic performance of porous-ceramic, thermal protection systems

NASA Astrophysics Data System (ADS)

Miller, Joshua E.; Bohl, William E.; Christiansen, Eric C.; Davis, Bruce A.; Foreman, Cory D.

2012-03-01

Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Orbiter, and they are currently being proposed for the next generation of US manned spacecraft, Orion. These systems insulate reentry critical components of a spacecraft against the intense thermal environments of atmospheric reentry. Additionally, these materials are highly exposed to space environment hazards like solid particle impacts. This paper discusses impact studies up to 10 km/s on 8 lb/ft3 alumina-fiber-enhanced-thermal-barrier (AETB8) tiles coated with a toughened-unipiece-fibrousinsulation/ reaction-cured-glass layer (TUFI/RCG). A semi-empirical, first principles impact model that describes projectile dispersion is described that provides excellent agreement with observations over a broad range of impact velocities, obliquities and projectile materials. Model extensions to look at the implications of greater than 10 GPa equation of state is also discussed. Predicted penetration probabilities for a vehicle visiting the International Space Station is 60% lower for orbital debris and 95% lower for meteoroids with this model compared to an energy scaled approach.

Wound ballistics 101: the mechanisms of soft tissue wounding by bullets.

PubMed

Stefanopoulos, P K; Pinialidis, D E; Hadjigeorgiou, G F; Filippakis, K N

2017-10-01

The mechanisms of soft tissue injury by bullets are reviewed, in the belief that the current incidence of firearm injuries in many urban areas necessitates an understanding of wound ballistics on the part of trauma surgeons who may not be familiar with the wounding factors involved. Review of the literature, with technical information obtained from appropriate non-medical texts. Despite numerous publications concerning the treatment of gunshot wounds, relatively few papers contain details on the mechanisms of ballistic trauma, with the main body of evidence derived from previous laboratory and animal studies which have only recently been systematically appraised. These studies have shown that in rifle injuries the main wound tract is surrounded by an area of damaged tissue as a result of the temporary cavitation induced once the bullet becomes destabilized or deformed. On the other hand, the more commonly encountered non-deforming handgun bullets cause damage limited to the bullet's path, mainly as a result of localized crush injury. The bullet's construction and ballistic behavior within tissue determine to what extent the previously overestimated velocity factor may influence wound severity. The damage produced from temporary cavitation depends on the tensile properties of the tissues involved, and in high-energy injuries may lead to progressive muscle tissue necrosis. Therefore, the term "high-energy" should be reserved for those injuries with substantial tissue damage extending beyond the visible wound tract.

A model for combined targeting and tracking tasks in computer applications.

PubMed

Senanayake, Ransalu; Hoffmann, Errol R; Goonetilleke, Ravindra S

2013-11-01

Current models for targeted-tracking are discussed and shown to be inadequate as a means of understanding the combined task of tracking, as in the Drury's paradigm, and having a final target to be aimed at, as in the Fitts' paradigm. It is shown that the task has to be split into components that are, in general, performed sequentially and have a movement time component dependent on the difficulty of the individual component of the task. In some cases, the task time may be controlled by the Fitts' task difficulty, and in others, it may be dominated by the Drury's task difficulty. Based on an experiment carried out that captured movement time in combinations of visually controlled and ballistic movements, a model for movement time in targeted-tracking was developed.

One Dimension Analytical Model of Normal Ballistic Impact on Ceramic/Metal Gradient Armor

NASA Astrophysics Data System (ADS)

Liu, Lisheng; Zhang, Qingjie; Zhai, Pengcheng; Cao, Dongfeng

2008-02-01

An analytical model of normal ballistic impact on the ceramic/metal gradient armor, which is based on modified Alekseevskii-Tate equations, has been developed. The process of gradient armour impacted by the long rod can be divided into four stages in this model. First stage is projectile's mass erosion or flowing phase, mushrooming phase and rigid phase; second one is the formation of comminuted ceramic conoid; third one is the penetration of gradient layer and last one is the penetration of metal back-up plate. The equations of third stage have been advanced by assuming the behavior of gradient layer as rigid-plastic and considering the effect of strain rate on the dynamic yield strength.

One Dimension Analytical Model of Normal Ballistic Impact on Ceramic/Metal Gradient Armor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu Lisheng; Zhang Qingjie; Zhai Pengcheng

2008-02-15

An analytical model of normal ballistic impact on the ceramic/metal gradient armor, which is based on modified Alekseevskii-Tate equations, has been developed. The process of gradient armour impacted by the long rod can be divided into four stages in this model. First stage is projectile's mass erosion or flowing phase, mushrooming phase and rigid phase; second one is the formation of comminuted ceramic conoid; third one is the penetration of gradient layer and last one is the penetration of metal back-up plate. The equations of third stage have been advanced by assuming the behavior of gradient layer as rigid-plastic andmore » considering the effect of strain rate on the dynamic yield strength.« less

Ballistic Testing for Interceptor Body Armor Inserts Needs Improvement

DTIC Science & Technology

2011-08-01

030, “Ballistic Testing and Product Quality Surveillance for the Interceptor Body Armor - Vest Components Need Improvement,” January 3, 2011. This...Body Armor Ballistic Inserts Interceptor Body Armor (IBA) is a modular body armor system that consists of an outer tactical vest , ballistic inserts...altitude tests was because the ceramic ballistic inserts are solid structures that are not sensitive to reduced pressure and moisture. PM SEQ offered no

Lead-Free Double-Base Propellant for the 2.75 Inch Rocket Motor

NASA Technical Reports Server (NTRS)

Magill, B. T.; Nauflett, G. W.; Furrow, K. W.

2000-01-01

The current MK 66 2.75 inch Rocket Motor double-base propellant contains the lead-based ballistic modifier LC-12-15 to achieve the desired plateau and mesa burning rate characteristics. The use of lead compounds poses a concern for the environment and for personal safety due to the metal's toxic nature when introduced into the atmosphere by propellant manufacture, rocket motor firing, and disposal. Copper beta-resorcylate (copper 2,4-di-hydroxy-benzoate) was successfully used in propellant as a simple modifier in the mid 1970's. This and other compounds have also been mixed with lead salts to obtain more beneficial ballistic results. Synthesized complexes of lead and copper compounds soon replaced the mixtures. The complexes incorporate the lead, copper lack of organic liquids, which allows for easier propellant processing. About ten years ago, the Indian Head Division, Naval Surface Warfare Center (NSWC), initiated an effort to develop a lead-free propellant for use in missile systems. Several lead-free propellant candidate formulations were developed. About five years ago, NSWC, in conjunction with Alliant Techsystems, Radford Army Ammunition Plant, continued ballistic modifier investigations. A four component ballistic modifier system without lead for double-base propellants that provide adequate plateau and mesa burn rate characteristics was developed and patented. The ballistic modifier's system contains bismuth subsalicylate, 1.5 percent; copper salicylate, 1.0 percent, copper stannate, 0.77 percent; and carbon black, 0.1 percent. Action time and impulse data obtained through multiple static firings indicate that the new lead-free double-base propellant, while not a match for NOSIH-AA-2, will be a very suitable replacement in the 2.75 inch Rocket Motor. Accelerated aging of the double-base propellant containing the lead-free ballistic modifier showed that it had a much higher rate of stabilizer depletion than the AA-2. A comprehensive study showed that an increased rate of stabilizer depletion occurred in propellants containing monobasic copper salicylate. The study also showed that propellants containing a mixture of bismuth subsalicylate and copper salicylate, had only about one-half the stabilizer depletion rate than those with copper salicylate alone. The copper salicylate catalyzes the decomposition of nitroglycerin, which triggers a chain of events leading to the increased rate of stabilizer depletion. A program has been initiated to coat the ballistic modifier, thus isolating it from the nitroglycerin.

Point of impact: the effect of size and speed on puncture mechanics.

PubMed

Anderson, P S L; LaCosse, J; Pankow, M

2016-06-06

The use of high-speed puncture mechanics for prey capture has been documented across a wide range of organisms, including vertebrates, arthropods, molluscs and cnidarians. These examples span four phyla and seven orders of magnitude difference in size. The commonality of these puncture systems offers an opportunity to explore how organisms at different scales and with different materials, morphologies and kinematics perform the same basic function. However, there is currently no framework for combining kinematic performance with cutting mechanics in biological puncture systems. Our aim here is to establish this framework by examining the effects of size and velocity in a series of controlled ballistic puncture experiments. Arrows of identical shape but varying in mass and speed were shot into cubes of ballistic gelatine. Results from high-speed videography show that projectile velocity can alter how the target gel responds to cutting. Mixed models comparing kinematic variables and puncture patterns indicate that the kinetic energy of a projectile is a better predictor of penetration than either momentum or velocity. These results form a foundation for studying the effects of impact on biological puncture, opening the door for future work to explore the influence of morphology and material organization on high-speed cutting dynamics.

HVI Ballistic Limit Characterization of Fused Silica Thermal Panes

NASA Technical Reports Server (NTRS)

Miller, J. E.; Bohl, W. D.; Christiansen, E. L.; Davis, B. A.; Deighton, K. D.

2015-01-01

Fused silica window systems are used heavily on crewed reentry vehicles, and they are currently being used on the next generation of US crewed spacecraft, Orion. These systems improve crew situational awareness and comfort, as well as, insulating the reentry critical components of a spacecraft against the intense thermal environments of atmospheric reentry. Additionally, these materials are highly exposed to space environment hazards like solid particle impacts. This paper discusses impact studies up to 10 km/s on a fused silica window system proposed for the Orion spacecraft. A ballistic limit equation that describes the threshold of perforation of a fuse silica pane over a broad range of impact velocities, obliquities and projectile materials is discussed here.

The thermal evolution of pyroclastic density currents: Exploring the thermal histories of juvenile clasts of Tungurahua and Cotopaxi, Ecuador

NASA Astrophysics Data System (ADS)

Benage, M. C.; Dufek, J.; Degruyter, W.

2010-12-01

The thermal history of pyroclastic density currents (PDCs) is critical in determining flow dynamics and deposit characteristics. The thermal history of these flows depends on the particles’ internal rate of heat transfer and heat exchange between discrete particles and a gas phase. We examine the thermal history of a class of dense PDC exemplified by the eruption of Tungurahua (2006) and Cotopaxi (1877) that have abundant breadcrust bombs segregated in levees and in flow snouts. An open question in this type of PDC is the amount of air entrainment (and cooling) during transport. To understand the entrainment and cooling history of these flows we use a multiphase numerical model coupled with a Lagrangian model (Eulerian-Eulerian-Lagrangian [EEL]) that tracks the internal heat transfer and post-eruption bubble evolution in juvenile clasts. We combine the numerical study with the observation of the morphology and vesicularity of breadcrust bombs from dense pyroclastic density currents from Tungurahua and Cotopaxi. Breadcrust bombs are common in many deposits from mafic explosive eruptions, e.g. Montserrat, Cotopaxi, Guagua Pichincha, and Tungurahua volcanoes. At many locations these bombs have likely been transported as ballistics (interacting mostly with ambient air), although several instances of dense scoria bomb flows have been noted (e.g. Cotopaxi and Tungurahua, Ecuador). The dense flow deposits are generally rich in unabraided breadcrust bombs along the flow levee and occasionally along the entire transect of the flow. The breadcrust bombs range in size from tens of centimeters to meters. They can also be found draping around previous deposits suggesting a high temperature of deposition. We discuss the use of clast morphology with other thermal proxies to better understand the thermal evolution of individual PDC and the proportion of time clasts underwent transport in dense flows as compared to ballistic transport.

Parameter recovery, bias and standard errors in the linear ballistic accumulator model.

PubMed

Visser, Ingmar; Poessé, Rens

2017-05-01

The linear ballistic accumulator (LBA) model (Brown & Heathcote, , Cogn. Psychol., 57, 153) is increasingly popular in modelling response times from experimental data. An R package, glba, has been developed to fit the LBA model using maximum likelihood estimation which is validated by means of a parameter recovery study. At sufficient sample sizes parameter recovery is good, whereas at smaller sample sizes there can be large bias in parameters. In a second simulation study, two methods for computing parameter standard errors are compared. The Hessian-based method is found to be adequate and is (much) faster than the alternative bootstrap method. The use of parameter standard errors in model selection and inference is illustrated in an example using data from an implicit learning experiment (Visser et al., , Mem. Cogn., 35, 1502). It is shown that typical implicit learning effects are captured by different parameters of the LBA model. © 2017 The British Psychological Society.

Nonequilibrium spin transport in integrable spin chains: Persistent currents and emergence of magnetic domains

NASA Astrophysics Data System (ADS)

De Luca, Andrea; Collura, Mario; De Nardis, Jacopo

2017-07-01

We construct exact steady states of unitary nonequilibrium time evolution in the gapless XXZ spin-1/2 chain where integrability preserves ballistic spin transport at long times. We characterize the quasilocal conserved quantities responsible for this feature and introduce a computationally effective way to evaluate their expectation values on generic matrix product initial states. We employ this approach to reproduce the long-time limit of local observables in all quantum quenches which explicitly break particle-hole or time-reversal symmetry. We focus on a class of initial states supporting persistent spin currents and our predictions remarkably agree with numerical simulations at long times. Furthermore, we propose a protocol for this model where interactions, even when antiferromagnetic, are responsible for the unbounded growth of a macroscopic magnetic domain.

Solution of the Lindblad equation for spin helix states.

PubMed

Popkov, V; Schütz, G M

2017-04-01

Using Lindblad dynamics we study quantum spin systems with dissipative boundary dynamics that generate a stationary nonequilibrium state with a nonvanishing spin current that is locally conserved except at the boundaries. We demonstrate that with suitably chosen boundary target states one can solve the many-body Lindblad equation exactly in any dimension. As solution we obtain pure states at any finite value of the dissipation strength and any system size. They are characterized by a helical stationary magnetization profile and a ballistic spin current which is independent of system size, even when the quantum spin system is not integrable. These results are derived in explicit form for the one-dimensional spin-1/2 Heisenberg chain and its higher-spin generalizations, which include the integrable spin-1 Zamolodchikov-Fateev model and the biquadratic Heisenberg chain.

Ballistic missile defense technologies

NASA Astrophysics Data System (ADS)

1985-09-01

A report on Ballistic Missile Technologies includes the following: Executive summary; Introduction; Ballistic missiles then and now; Deterrence, U.S. nuclear strategy, and BMD; BMD capabilities and the strategic balance; Crisis stability, arms race stability, and arms control issues; Ballistic missile defense technologies; Feasibility; Alternative future scenarios; Alternative R&D programs.

76 FR 14589 - Defense Federal Acquisition Regulation Supplement; Repeal of Restriction on Ballistic Missile...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-17

...-AH18 Defense Federal Acquisition Regulation Supplement; Repeal of Restriction on Ballistic Missile...). Section 222 repeals the restriction on purchase of Ballistic Missile Defense research, development, test... Ballistic Missile Defense research, development, test, and evaluation that was required by section 222 of...

Experimental observation of ballistic nanofriction on graphene

NASA Astrophysics Data System (ADS)

Blue, Brandon; Lodge, Michael; Tang, Chun; Hubbard, William; Martini, Ashlie; Dawson, Ben; Ishigami, Masa

Recent calculations have predicted that gold nanocrystals slide on graphite with two radically different friction coefficients depending on their speeds. At high sliding speeds in the range of 100?m/s, nanocrystals are expected to behave radically differently in what is known as the ballistic nanofriction regime. In this work, we present a direct measurement of ballistic nanofriction for gold nanocrystals on graphene. Nanocrystals are deposited onto an oscillating graphene-coated quartz crystal microbalance (QCM) in-situ under UHV and allowed to periodically ring down. After deposition, frictional parameters are measured as a function of oscillatory velocity to investigate the predicted velocity dependence of friction. Lubricity beyond even the predictions of ballistic nanofriction is observed at much lower surface velocities than expected, with drag coefficients approaching 8.65*10-14 kg/s. In comparison to the theoretically-predicted value of 2.0*10-13 kg/s, our results suggest a much lower interaction strength than proposed in contemporary models of nanoscopic sliding contacts even at relatively low speeds. This work is based on research supported by the National Science Foundation, Grant No. 0955625 (MLS, BTB, BDD and MI) and Grant No. CMMI-1265594 (CT and AM). BDD and MI were also supported by the Intelligence Community Postdoctoral Fellowship.

Stability analyses of the mass abrasive projectile high-speed penetrating into a concrete target Part III: Terminal ballistic trajectory analyses

NASA Astrophysics Data System (ADS)

Wu, H.; Chen, X. W.; Fang, Q.; Kong, X. Z.; He, L. L.

2015-08-01

During the high-speed penetration of projectiles into concrete targets (the impact velocity ranges from 1.0 to 1.5 km/s), important factors such as the incident oblique and attacking angles, as well as the asymmetric abrasions of the projectile nose induced by the target-projectile interactions, may lead to obvious deviation of the terminal ballistic trajectory and reduction of the penetration efficiency. Based on the engineering model for the mass loss and nose-blunting of ogive-nosed projectiles established, by using the Differential Area Force Law (DAFL) method and semi-empirical resistance function, a finite differential approach was programmed (PENTRA2D) for predicting the terminal ballistic trajectory of mass abrasive high-speed projectiles penetrating into concrete targets. It accounts for the free-surface effects on the drag force acting on the projectile, which are attributed to the oblique and attacking angles, as well as the asymmetric nose abrasion of the projectile. Its validation on the prediction of curvilinear trajectories of non-normal high-speed penetrators into concrete targets is verified by comparison with available test data. Relevant parametric influential analyses show that the most influential factor for the stability of terminal ballistic trajectories is the attacking angle, followed by the oblique angle, the discrepancy of asymmetric nose abrasion, and the location of mass center of projectile. The terminal ballistic trajectory deviations are aggravated as the above four parameters increase.

Numerical Simulation of Ballistic Impact on Particulate Composite Target using Discrete Element Method: 1-D and 2-D Models

NASA Astrophysics Data System (ADS)

Nair, Rajesh P.; Lakshmana Rao, C.

2014-01-01

Ballistic impact (BI) is a study that deals with a projectile hitting a target and observing its effects in terms of deformation and fragmentation of the target. The Discrete Element Method (DEM) is a powerful numerical technique used to model solid and particulate media. Here, an attempt is made to simulate the BI process using DEM. 1-D DEM for BI is developed and depth of penetration (DOP) is obtained. The DOP is compared with results obtained from 2-D DEM. DEM results are found to match empirical results. Effects of strain rate sensitivity of the material response on DOP are also simulated.

Space Shuttle: Reentry stability and performance characteristics in the transonic and supersonic flight regimes of the Boeing ballistic recoverable booster

NASA Technical Reports Server (NTRS)

Houser, J.; Vanderleest, S.

1972-01-01

Experimental aerodynamic investigations were made in transonic and supersonic wind tunnels on a .008899 scale model of the Boeing model 979-145 Ballistic Recoverable Booster. The purpose of the tests was to define the stability and performance characteristics of the BRB at re-entry attitudes in the transonic and supersonic flight regimes. Data were obtained over a Mach number range from 0.6 to 4.0 at angles of attack between 50 deg and 85 deg at zero sideslip and at angles of sideslip between -17.5 deg and +15 deg at angles of attack between 50 deg and 85 deg.

Effect of concentric and eccentric velocity during heavy-load non-ballistic elbow flexion resistance exercise.

PubMed

Sampson, John A; Donohoe, Alison; Groeller, Herbert

2014-05-01

Mechanical and neuromuscular benefits arise during ballistic stretch-shortening cycle muscle activation, yet resistance training regimens are typically non-ballistic, and in contrast to ballistic movement, require a concentric deceleration phase. Twelve healthy males performed a unilateral, six repetition maximum non-ballistic elbow flexion-extension task during; (i) rapid shortening (RS), (ii) stretch-shortening cycle (SSC) and (iii) a 2-s eccentric and 2-s concentric control (C). A load cell and shaft encoder recorded respectively force and velocity. Surface electromyographic root mean square amplitude (EMGRMS) was recorded in the biceps and triceps brachii, and is reported as the relative (%) difference, normalised to control (C). The average lengthening and shortening velocity of SSC (0.57 ± 0.03 ms(-1); 0.43 ± 0.02 ms(-1)) was significantly greater than RS (0.22 ± 0.01 ms(-1); 0.35 ± 0.01 ms(-1)), and C (0.17 ± 0.00 ms(-1), 0.20 ± 0.00 ms(-1)). Peak eccentric force was increased (P<0.0001) and in the first 5% of concentric movement during SSC, in the first and last repetitions respectively (194.7 ± 8.4N, 164.1 ± 7.5 N) when compared to RS (163.3 ± 8.9 N, 152.4 ± 7.5 N) and C (155.9 ± 8.5 N, 152.2 ± 8.7 N). Eccentric EMGRMS in the biceps brachii was significantly increased during the first three and final repetitions of SSC (31.9 ± 10.9%, 46.7 ± 12.4, 69.3 ± 13.6%, 92.0 ± 16.4%), and the third and last repetitions of RS (35.9 ± 7.4%, 50.3 ± 10.9%), compared to C (0.00%, 15.8 ± 4.0%, 23.7 ± 4.1%, 39.2 ± 8.6%). In the current study, eccentric limb velocity potentiated eccentric and concentric force, concentric velocity, and eccentric EMG amplitude during non-ballistic exercise. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Magnetic field oscillations of the critical current in long ballistic graphene Josephson junctions

NASA Astrophysics Data System (ADS)

Rakyta, Péter; Kormányos, Andor; Cserti, József

2016-06-01

We study the Josephson current in long ballistic superconductor-monolayer graphene-superconductor junctions. As a first step, we have developed an efficient computational approach to calculate the Josephson current in tight-binding systems. This approach can be particularly useful in the long-junction limit, which has hitherto attracted less theoretical interest but has recently become experimentally relevant. We use this computational approach to study the dependence of the critical current on the junction geometry, doping level, and an applied perpendicular magnetic field B . In zero magnetic field we find a good qualitative agreement with the recent experiment of M. Ben Shalom et al. [Nat. Phys. 12, 318 (2016), 10.1038/nphys3592] for the length dependence of the critical current. For highly doped samples our numerical calculations show a broad agreement with the results of the quasiclassical formalism. In this case the critical current exhibits Fraunhofer-like oscillations as a function of B . However, for lower doping levels, where the cyclotron orbit becomes comparable to the characteristic geometrical length scales of the system, deviations from the results of the quasiclassical formalism appear. We argue that due to the exceptional tunability and long mean free path of graphene systems a new regime can be explored where geometrical and dynamical effects are equally important to understand the magnetic field dependence of the critical current.

A method for simulating the atmospheric entry of long-range ballistic missiles

NASA Technical Reports Server (NTRS)

Eggers, A J , Jr

1958-01-01

It is demonstrated with the aid of similitude arguments that a model launched from a hypervelocity gun upstream through a special supersonic nozzle should experience aerodynamic heating and resulting thermal stresses like those encountered by a long-range ballistic missile entering the earth's atmosphere. This demonstration hinges on the requirements that model and missile be geometrically similar and made of the same material, and that they have the same flight speed and Reynolds number (based on conditions just outside the boundary layer) at corresponding points in their trajectories. The hypervelocity gun provides the model with the required initial speed, while the nozzle scales the atmosphere, in terms of density variation, to provide the model with speeds and Reynolds numbers over its entire trajectory. Since both the motion and aerodynamic heating of a missile tend to be simulated in the model tests, this combination of hypervelocity gun and supersonic nozzle is termed an atmosphere entry simulator.

Using Computer Simulations to Model Scoria Cone Growth

NASA Astrophysics Data System (ADS)

Bemis, K. G.; Mehta, R. D.

2016-12-01

Scoria cones form from the accumulation of scoria delivered by either bursting lava bubbles (Strombolian style eruptions) or the gas thrust of an eruption column (Hawaiian to sub-Plinian style eruption). In this study, we focus on connecting the distribution of scoria delivery to the eventual cone shape rather than the specifics of the mechanism of delivery. For simplicity, we choose to model ballistic paths, that follow the scoria from ejection from crater to landing on the surface and then avalanching down slope. The first stage corresponds to Strombolian-like bursts of the bubble. The second stage only occurs if the angle of repose is greater than 30 degrees. After this condition is met, the scoria particles grain flow downwards until a stable slope is formed. These two stages of the volcanic eruption repeat themselves in the number of phases. We hypothesize that the horizontal travel distance of the ballistic paths, and as a result the width of the volcano, is primarily dependent of the velocity of the particles bursting from the bubble in the crater. Other parameters that may affect the shape of cinder cones are air resistance on ballistic paths, ranges in particle size, ballistic ejection angles, and the total number of particles. Ejection velocity, ejection angle, particle size and air resistance control the delivery distribution of scoria; a similar distribution of scoria can be obtained by sedimentation from columns and the controlling parameters of such (gas thrust velocity, particle density, etc.) can be related to the ballistic delivery in terms of eruption energy and particle characteristics. We present a series of numerical experiments that test our hypotheses by varying different parameters one or more at a time in sets each designed to test a specific hypothesis. Volcano width increases as ejection velocity, ejection angle (measured from surface), or the total number of scoria particles increases. Ongoing investigations seek the controls on crater width.

Analysis of ballistic transport in nanoscale devices by using an accelerated finite element contact block reduction approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, H.; Li, G., E-mail: gli@clemson.edu

2014-08-28

An accelerated Finite Element Contact Block Reduction (FECBR) approach is presented for computational analysis of ballistic transport in nanoscale electronic devices with arbitrary geometry and unstructured mesh. Finite element formulation is developed for the theoretical CBR/Poisson model. The FECBR approach is accelerated through eigen-pair reduction, lead mode space projection, and component mode synthesis techniques. The accelerated FECBR is applied to perform quantum mechanical ballistic transport analysis of a DG-MOSFET with taper-shaped extensions and a DG-MOSFET with Si/SiO{sub 2} interface roughness. The computed electrical transport properties of the devices obtained from the accelerated FECBR approach and associated computational cost as amore » function of system degrees of freedom are compared with those obtained from the original CBR and direct inversion methods. The performance of the accelerated FECBR in both its accuracy and efficiency is demonstrated.« less

Observation of strong reflection of electron waves exiting a ballistic channel at low energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaz, Canute I.; Campbell, Jason P.; Ryan, Jason T.

2016-06-15

Wave scattering by a potential step is a ubiquitous concept. Thus, it is surprising that theoretical treatments of ballistic transport in nanoscale devices, from quantum point contacts to ballistic transistors, assume no reflection even when the potential step is encountered upon exiting the device. Experiments so far seem to support this even if it is not clear why. Here we report clear evidence of coherent reflection when electron wave exits the channel of a nanoscale transistor and when the electron energy is low. The observed behavior is well described by a simple rectangular potential barrier model which the Schrodinger’s equationmore » can be solved exactly. We can explain why reflection is not observed in most situations but cannot be ignored in some important situations. Our experiment also represents a direct measurement of electron injection velocity - a critical quantity in nanoscale transistors that is widely considered not measurable.« less

Finite element analysis for the evaluation of protective functions of helmets against ballistic impact.

PubMed

Lee, H P; Gong, S W

2010-10-01

The ballistic impact of a human head model protected by a Personnel Armor System Ground Troops Kevlar® helmet is analysed using the finite element method. The emphasis is to examine the effect of the interior cushioning system as a shock absorber in mitigating ballistic impact to the head. The simulations of the frontal and side impacts of the full metal jacket (FMJ) and fragment-simulating projectile (FSP) were carried out using LS-DYNA. It was found that the Kevlar® helmet with its interior nylon and leather strap was able to defeat both the FMJ and FSP without the projectiles penetrating the helmet. However, the head injuries caused by the FMJ impact can be fatal due to the high stiffness of the interior strap. The bulge section at the side of the Kevlar® helmet had more room for deformation that resulted in less serious head injuries.

48 CFR 252.225-7018 - Notice of prohibition of certain contracts with foreign entities for the conduct of ballistic...

Code of Federal Regulations, 2010 CFR

2010-10-01

... certain contracts with foreign entities for the conduct of ballistic missile defense research, development... foreign entities for the conduct of ballistic missile defense research, development, test, and evaluation... With Foreign Entities for the Conduct of Ballistic Missile Defense Research, Development, Test, and...

Definition of an anti-missile ballistic defense architecture for Europe

NASA Astrophysics Data System (ADS)

Deas, M.; Tanter, A.

1995-01-01

The end of the Seventies and beginning of the Eighties showed significant technological developments in ballistic missiles, in particular,impact precision. These improvements caused Western strategists to be concerned with use of ballistic missiles equipped with conventional loads against military objectives (the Pact of Varsovie). The concept of ballistic missile tactical had been born. The ballistic vector, which until this time was marked with a 'strategic' label, was then 'standardized' and has interested a number of countries in the process of its development. The world has just entered the era of the ballistic proliferation. From the very start of the Eighties, the United States and, to a lesser degree, NATO lead studies and reflections concerned with defense against tactical ballistic missiles within a East West framework. From these studies the ATBM (Anti Tactical Ballistic Missile) made its appearance. In spite of the attempts at control, missile proliferation has accelerated and led, towards the end of the Eighties and the beginning of the Nineties, to the awakening of a new risk known as proliferating. The 1991 Gulf War was accelerated in this manner. This conflict also clarified the fact that the ballistic weapon constituted a formidable means of pressure for countries which had it, in spite of the PATRIOT, which demonstrated the feasibility of an active defense against ballistic missiles, in spite of their limited performances. This present presentation proposes an overall analysis of the ballistic risk and the possible threat which could result from it and examines the means available for protection against this risk by looking further into all the defensive means. This will constitute the main part of the speech. Lastly, we will endeavor to evaluate the difficulties faced by the architects of the DAMB.

Monte Carlo simulation of nonadiabatic expansion in cometary atmospheres - Halley

NASA Astrophysics Data System (ADS)

Hodges, R. R.

1990-02-01

Monte Carlo methods developed for the characterization of velocity-dependent collision processes and ballistic transports in planetary exospheres form the basis of the present computer simulation of icy comet atmospheres, which iteratively undertakes the simultaneous determination of velocity distribution for five neutral species (water, together with suprathermal OH, H2, O, and H) in a flow regime varying from the hydrodynamic to the ballistic. Experimental data from the neutral mass spectrometer carried by Giotto for its March, 1986 encounter with Halley are compared with a model atmosphere.

Stochastic theory of photon flow in homogeneous and heterogeneous anisotropic biological and artificial material

NASA Astrophysics Data System (ADS)

Miller, Steven D.

1995-05-01

Standard Monte Carlo methods used in photon diffusion score absorbed photons or statistical weight deposited within voxels comprising a mesh. An alternative approach to a stochastic description is considered for rapid surface flux calculations and finite medias. Matrix elements are assigned to a spatial lattice whose function is to score vector intersections of scattered photons making transitions into either the forward or back solid angle half spaces. These complete matrix elements can be related to the directional fluxes within the lattice space. This model differentiates between ballistic, quasi-ballistic, and highly diffuse photon contributions, and effectively models the subsurface generation of a scattered light flux from a ballistic source. The connection between a path integral and diffusion is illustrated. Flux perturbations can be effectively illustrated for tissue-tumor-tissue and for 3 layer systems with strong absorption in one or more layers. For conditions where the diffusion theory has difficulties such as strong absorption, highly collimated sources, small finite volumes, and subsurface regions, the computation time of the algorithm is rapid with good accuracy and compliments other description of photon diffusion. The model has the potential to do computations relevant to photodynamic therapy (PDT) and analysis of laser beam interaction with tissues.

"Ballistic Six" Upper-Extremity Plyometric Training for the Pediatric Volleyball Players.

PubMed

Turgut, Elif; Cinar-Medeni, Ozge; Colakoglu, Filiz F; Baltaci, Gul

2017-09-19

The Ballistic Six exercise program includes commonly used upper-body exercises, and the program is recommended for overhead throwing athletes. The purpose of the current study was to investigate the effects of a 12-week the Ballistic Six upper-extremity plyometric training program on upper-body explosive power, endurance, and reaction time in pediatric overhead athletes. Twenty-eight female pediatric volleyball players participated in the study. The participants were randomly divided into 2 study groups: an intervention group (upper-extremity plyometric training in addition to the volleyball training; n = 14) and a control group (the volleyball training only; n = 14). All the participants were assessed before and after a 12-week training program for upper-body power, strength and endurance, and reaction time. Statistical comparison was performed using an analysis of variance test. Comparisons showed that after a 12-week training program, the Ballistic Six upper-body plyometric training program resulted in more improvements in an overhead medicine ball throwing distance and a push-up performance, as well as greater improvements in the reaction time in the nonthrowing arm when compared with control training. In addition, a 12-week training program was found to be effective in achieving improvements in the reaction time in the throwing arm for both groups similarly. Compared with regular training, upper-body plyometric training resulted in additional improvements in upper-body power and strength and endurance among pediatric volleyball players. The findings of the study provide a basis for developing training protocols for pediatric volleyball players.

The effect of high-pressure devitrification and densification on ballistic-penetration resistance of fused silica

NASA Astrophysics Data System (ADS)

Avuthu, Vasudeva Reddy

Despite the clear benefits offered by more advanced transparent materials, (e.g. transparent ceramics offer a very attractive combination of high stiffness and high hardness levels, highly-ductile transparent polymers provide superior fragment-containing capabilities, etc.), ballistic ceramic-glass like fused-silica remains an important constituent material in a majority of transparent impact-resistant structures (e.g. windshields and windows of military vehicles, portholes in ships, ground vehicles and spacecraft) used today. Among the main reasons for the wide-scale use of glass, the following three are most frequently cited: (i) glass-structure fabrication technologies enable the production of curved, large surface-area, transparent structures with thickness approaching several inches; (ii) relatively low material and manufacturing costs; and (iii) compositional modifications, chemical strengthening, and controlled crystallization have been demonstrated to be capable of significantly improving the ballistic properties of glass. In the present work, the potential of high-pressure devitrification and densification of fused-silica as a ballistic-resistance-enhancement mechanism is investigated computationally. In the first part of the present work, all-atom molecular-level computations are carried out to infer the dynamic response and material microstructure/topology changes of fused silica subjected to ballistic impact by a nanometer-sized hard projectile. The analysis was focused on the investigation of specific aspects of the dynamic response and of the microstructural changes such as the deformation of highly sheared and densified regions, and the conversion of amorphous fused silica to SiO2 crystalline allotropic modifications (in particular, alpha-quartz and stishovite). The microstructural changes in question were determined by carrying out a post-processing atom-coordination procedure. This procedure suggested the formation of high-density stishovite (and perhaps alpha-quartz) within fused silica during ballistic impact. To rationalize the findings obtained, the all-atom molecular-level computational analysis is complemented by a series of quantum-mechanics density functional theory (DFT) computations. The latter computations enable determination of the relative potential energies of the fused silica, alpha-quartz and stishovite under ambient pressure (i.e. under their natural densities) as well as under imposed (as high as 50 GPa) pressures (i.e. under higher densities) and shear strains. In addition, the transition states associated with various fused-silica devitrification processes were identified. In the second part of the present work, the molecular-level computational results obtained in the first portion of the work are used to enrich a continuum-type constitutive model (that is, the so-called Johnson-Holmquist-2, JH2, model) for fused silica. Since the aforementioned devitrification and permanent-densification processes modify the response of fused silica to the pressure as well as to the deviatoric part of the stress, changes had to be made in both the JH2 equation of state and the strength model. To assess the potential improvements with respect to the ballistic-penetration resistance of this material brought about by the fused-silica devitrification and permanent-densification processes, a series of transient non-linear dynamics finite element analyses of the transverse impact of a fused-silica test plate with a solid right-circular cylindrical steel projectile was conducted. The results obtained revealed that, provided the projectile incident velocity and, hence, the attendant pressure, is sufficiently high, fused silica can undergo impact-induced energy-consuming devitrification, which improves its ballistic-penetration resistance.

Wound ballistics: theory and practice.

PubMed

Ordog, G J; Wasserberger, J; Balasubramanium, S

1984-12-01

Ballistics is the study of the natural laws governing projectile missiles and their predictable performances, and wound ballistics is the study of a missile's effect on living tissue. A knowledge of these topics is essential to determine the extent and type of injury from a missile. The type of missile can often be determined by radiography. The caliber can be measured directly if the bullet is close to the x-ray plate and the x-ray tube is at least six feet from the film. Changing these distances can result in a maximum magnification of the bullet image of 20%, and the exact amount can be calculated using a formula provided. Definitions of ballistic and wound ballistic terms are provided, as are examples of wound ballistics in application.

Josephson-like spin current in junctions composed of antiferromagnets and ferromagnets

NASA Astrophysics Data System (ADS)

Moor, A.; Volkov, A. F.; Efetov, K. B.

2012-01-01

We study Josephson-like junctions formed by materials with antiferromagnetic (AF) order parameters. As an antiferromagnet, we consider a two-band material in which a spin density wave (SDW) arises. This could be Fe-based pnictides in the temperature interval Tc≤T≤TN, where Tc and TN are the critical temperatures for the superconducting and antiferromagnetic transitions, respectively. The spin current jSp in AF/F/AF junctions with a ballistic ferromagnetic layer and in tunnel AF/I/AF junctions is calculated. It depends on the angle between the magnetization vectors in the AF leads in the same way as the Josephson current depends on the phase difference of the superconducting order parameters in S/I/S tunnel junctions. It turns out that in AF/F/AF junctions, two components of the SDW order parameter are induced in the F layer. One of them oscillates in space with a short period ξF,b˜ℏv/H, while the other decays monotonously from the interfaces over a long distance of the order ξN,b=ℏv/2πT (where v, H, and T are the Fermi velocity, the exchange energy, and the temperature, respectively; the subindex “b” denotes the ballistic case). This is a clear analogy with the case of Josephson S/F/S junctions with a nonhomogeneous magnetization where short- and long-range condensate components are induced in the F layer. However, in contrast to the charge Josephson current in S/F/S junctions, the spin current in AF/F/AF junctions is not constant in space, but oscillates in the ballistic F layer. We also calculate the dependence of jSp on the deviation from the ideal nesting in the AF/I/AF junctions. The spin current is maximal in the insulating phase of the AF and decreases in the metallic phase. It turns to zero at the Neel point when the amplitude of the SDW is zero and changes sign for certain values of the detuning parameter.

Parachuting to Safety

NASA Technical Reports Server (NTRS)

2002-01-01

NASA's Langley Research Center awarded Ballistic Recovery Systems, Inc., three Small Business Innovation Research (SBIR) contracts to research and develop a new, low cost, lightweight recovery system for aircraft in both civilian and military markets. The company responded with a unique ballistic parachute system that lowers an entire aircraft to the ground in the event of an emergency. BRS parachutes are designed to provide a safe landing for pilots and passengers while keeping them in their aircraft. They currently fit ultralights, kit-built aircraft, and certified small business aircraft. The parachutes are lifesavers in cases of engine failure, mid-air collisions, pilot disorientation or incapacitation, unrecovered spins, extreme icing, and fuel exhaustion. To date, over 148 lives were saved as a result of a BRS parachute system.

Methods for Analysis and Simulation of Ballistic Impact

DTIC Science & Technology

2017-04-01

ARL-RP-0597 ● Apr 2017 US Army Research Laboratory Methods for Analysis and Simulation of Ballistic Impact by John D Clayton...Laboratory Methods for Analysis and Simulation of Ballistic Impact by John D Clayton Weapons and Materials Research Directorate, ARL...analytical, and numerical methods of ballistics research . Similar lengthy references dealing with pertinent aspects include [8, 9]. In contrast, the

Ballistic impacts on an anatomically correct synthetic skull with a surrogate skin/soft tissue layer.

PubMed

Mahoney, Peter; Carr, Debra; Arm, Richard; Gibb, Iain; Hunt, Nicholas; Delaney, Russ J

2018-03-01

The aim of this work was to further develop a synthetic model of ballistic head injury by the addition of skin and soft tissue layers to an anatomically correct polyurethane skull filled with gelatine 10% by mass. Six head models were impacted with 7.62 x 39 mm full metal jacket mild steel core (FMJ MSC) bullets with a mean velocity of 652 m/s. The impact events were filmed with high-speed cameras. The models were imaged pre- and post-impact using computed tomography. The models were assessed post impact by two experienced Home Office pathologists and the images assessed by an experienced military radiologist. The findings were scored against real injuries. The entry wounds, exit wounds and fracture patterns were scored positively, but the synthetic skin and soft tissue layer was felt to be too extendable. Further work is ongoing to address this.

Getting more from accuracy and response time data: methods for fitting the linear ballistic accumulator.

PubMed

Donkin, Chris; Averell, Lee; Brown, Scott; Heathcote, Andrew

2009-11-01

Cognitive models of the decision process provide greater insight into response time and accuracy than do standard ANOVA techniques. However, such models can be mathematically and computationally difficult to apply. We provide instructions and computer code for three methods for estimating the parameters of the linear ballistic accumulator (LBA), a new and computationally tractable model of decisions between two or more choices. These methods-a Microsoft Excel worksheet, scripts for the statistical program R, and code for implementation of the LBA into the Bayesian sampling software WinBUGS-vary in their flexibility and user accessibility. We also provide scripts in R that produce a graphical summary of the data and model predictions. In a simulation study, we explored the effect of sample size on parameter recovery for each method. The materials discussed in this article may be downloaded as a supplement from http://brm.psychonomic-journals.org/content/supplemental.

Tunnel and field effect carrier ballistics

NASA Technical Reports Server (NTRS)

Kaiser, William J. (Inventor); Bell, L. Douglas (Inventor)

1989-01-01

Methods and apparatus for interacting carriers with a structure of matter employ an electrode for emitting said carriers at a distance from a surface of that structure, and cause such carriers to travel along ballistic trajectories inside that structure by providing along the mentioned distance a gap for performance of a process selected from the group of carrier tunneling and field emission and injecting carriers emitted by the mentioned electrode and that process ballistically into the structure through the gap and the mentioned surface. The carriers are collected or analyzed after their travel along ballistic trajectories in the structure of matter. Pertinent information on the inside of the structure is obtained by conducting inside that structure what conventionally would have been considered external ballistics, while performing the carrier-propelling internal ballistics conversely outside that structure.

CFD Simulations of the Supersonic Inflatable Aerodynamic Decelerator (SIAD) Ballistic Range Tests

NASA Technical Reports Server (NTRS)

Brock, Joseph; Stern, Eric; Wilder, Michael

2017-01-01

A series of ballistic range tests were performed on a scaled model of the Supersonic Flight Demonstration Test (SFDT) intended to test the Supersonic Inflatable Aerodynamic Decelerator (SIAD) geometry. The purpose of these experiments were to provide aerodynamic coefficients of the vehicle to aid in mission and vehicle design. The experimental data spans the moderate Mach number range, $3.8-2.0$, with a total angle of attack ($alpha_T$) range, $10o-20o$. These conditions are intended to span the Mach-$alpha$ space for the majority of the SFDT experiment. In an effort to validate the predictive capabilities of Computational Fluid Dynamics (CFD) for free-flight aerodynamic behavior, numerical simulations of the ballistic range experiment are performed using the unstructured finite volume Navier-Stokes solver, US3D. Comparisons to raw vehicle attitude, and post-processed aerodynamic coefficients are made between simulated results and experimental data. The resulting comparisons for both raw model attitude and derived aerodynamic coefficients show good agreement with experimental results. Additionally, near body pressure field values for each trajectory simulated are investigated. Extracted surface and wake pressure data gives further insights into dynamic flow coupling leading to a potential mechanism for dynamic instability.

Curvilinear trajectory estimation of a supersonic bullet using ballistic shock wave arrivals at asynchronous acoustic sensor nodes.

PubMed

Lo, Kam W

2017-06-01

The trajectory of a supersonic bullet, which is subjected to drag and gravity, is curvilinear and the supersonic flight of the bullet generates a ballistic shock wave (SW). A model for the differential time of arrival (DTOA) of the SW at a pair of acoustic sensors is derived for a given bullet trajectory, which is fully described by seven parameters including the drag coefficient exponent and ballistic constant of the bullet. Assuming that the drag coefficient exponent is 0.5, the DTOA model is used to develop a nonlinear least-squares (NLS) method to estimate the other six trajectory parameters using DTOA of SW measurements from each node (which comprises a small acoustic sensor array) of an asynchronous sensor network. The position of the shooter and the muzzle speed of the bullet are then determined by tracing the estimated bullet trajectory back to topographic or man-made obstructions on a digital map. The effectiveness of the NLS method is verified using simulated data for different types of real bullets, and the error standard deviations in the parameter estimates are close to the Cramer-Rao lower bounds.

Helmet Sensor - Transfer Function and Model Development

DTIC Science & Technology

2010-09-01

These events could be exposure to blast events (IEDs), ballistic  impacts , and/or blunt  impacts .  The sensors record orthogonal accelerations and blast...during  impact , the measured helmet response will be  different from the head response.  The objective of this effort is the characterize the...numerical equations or  models) that approximate head exposures based on the observed helmet response.  The physical testing included ballistic  impact

Thermodynamic properties of UF sub 6 measured with a ballistic piston compressor

NASA Technical Reports Server (NTRS)

Sterritt, D. E.; Lalos, G. T.; Schneider, R. T.

1973-01-01

From experiments performed with a ballistic piston compressor, certain thermodynamic properties of uranium hexafluoride were investigated. Difficulties presented by the nonideal processes encountered in ballistic compressors are discussed and a computer code BCCC (Ballistic Compressor Computer Code) is developed to analyze the experimental data. The BCCC unfolds the thermodynamic properties of uranium hexafluoride from the helium-uranium hexafluoride mixture used as the test gas in the ballistic compressor. The thermodynamic properties deduced include the specific heat at constant volume, the ratio of specific heats for UF6, and the viscous coupling constant of helium-uranium hexafluoride mixtures.

Twin lead ballistic conductor based on nanoribbon edge transport

NASA Astrophysics Data System (ADS)

Konôpka, Martin; Dieška, Peter

2018-03-01

If a device like a graphene nanoribbon (GNR) has all its four corners attached to electric current leads, the device becomes a quantum junction through which two electrical circuits can interact. We study such system theoretically for stationary currents. The 4-point energy-dependent conductance matrix of the nanostructure and the classical resistors in the circuits are parameters of the model. The two bias voltages in the circuits are the control variables of the studied system while the electrochemical potentials at the device's terminals are non-trivially dependent on the voltages. For the special case of the linear-response regime analytical formulae for the operation of the coupled quantum-classical device are derived and applied. For higher bias voltages numerical solutions are obtained. The effects of non-equilibrium Fermi levels are captured using a recursive algorithm in which self-consistency between the electrochemical potentials and the currents is reached within few iterations. The developed approach allows to study scenarios ranging from independent circuits to strongly coupled ones. For the chosen model of the GNR with highly conductive zigzag edges we determine the regime in which the single device carries two almost independent currents.

The Effects of Multiple Sets of Squats and Jump Squats on Mechanical Variables.

PubMed

Rossetti, Michael L; Munford, Shawn N; Snyder, Brandon W; Davis, Shala E; Moir, Gavin L

2017-07-28

The mechanical responses to two non-ballistic squat and two ballistic jump squat protocols performed over multiple sets were investigated. One protocol from each of the two non-ballistic and ballistic conditions incorporated a pause between the eccentric and concentric phases of the movements in order to determine the influence of the coupling time on the mechanical variables and post-activation potentiation (PAP). Eleven men (age: 21.9 ± 1.8 years; height: 1.79 ± 0.05 m; mass: 87.0 ± 7.4 kg) attended four sessions where they performed multiple sets of squats and jump squats with a load equivalent to 30% 1-repeititon maximum under one of the following conditions: 1) 3 × 4 repetitions of non-ballistic squats (30N-B); 2) 3 × 4 repetitions of non-ballistic squats with a 3-second pause between the eccentric and concentric phases of each repetition (30PN-B); 3) 3 × 4 repetitions of ballistic jump squats (30B); 4) 3 × 4 repetitions of ballistic jump squats with a 3-second pause between the eccentric and concentric phases of each repetition (30PB). Force plates were used to calculate variables including average vertical velocity, average vertical force (GRF), and average power output (PO). Vertical velocities during the ballistic conditions were significantly greater than those attained during the non-ballistic conditions (mean differences: 0.21 - 0.25 m/s, p<0.001, effect sizes [ES]: 1.70 - 1.89) as were GRFs (mean differences: 478 - 526 N, p<0.001, ES: 1.61 - 1.63), and PO (mean differences: 711 - 869 W, p<0.001, ES: 1.66 - 1.73). Moreover, the increase in PO across the three sets in 30B was significantly greater than the changes observed during 30N-B, 30PN-B, and 30PB (p≤0.015). The pause reduced the mechanical variables during both the non-ballistic and ballistic conditions, although the differences were not statistically significant (p>0.05). Ballistic jump squats may be an effective exercise for developing PO given the high velocities and forces generated in these exercises. Furthermore, the completion of multiple sets of jump squats may induce PAP to enhance PO. The coupling times between the eccentric and concentric phases of the jump squats should be short in order to maximize the GRF and PO across the sets.

Understanding the ballistic event : Methodology and observations relevant to ceramic armour

NASA Astrophysics Data System (ADS)

Healey, Adam

The only widely-accepted method of gauging the ballistic performance of a material is to carry out ballistic testing; due to the large volume of material required for a statistically robust test, this process is very expensive. Therefore a new test, or suite of tests, that employ widely-available and economically viable characterisation methods to screen candidate armour materials is highly desirable; in order to design such a test, more information on the armour/projectile interaction is required. This work presents the design process and results of using an adapted specimen configuration to increase the amount of information obtained from a ballistic test. By using a block of ballistic gel attached to the ceramic, the fragmentation generated during the ballistic event was captured and analysed. In parallel, quasi-static tests were carried out using ring-on-ring biaxial disc testing to investigate relationships between quasi-static and ballistic fragment fracture surfaces. Three contemporary ceramic armour materials were used to design the test and to act as a baseline; Sintox FA alumina, Hexoloy SA silicon carbide and 3M boron carbide. Attempts to analyse the post-test ballistic sample non-destructively using X-ray computed tomography (XCT) were unsuccessful due to the difference in the density of the materials and the compaction of fragments. However, the results of qualitative and quantitative fracture surface analysis using scanning electron microscopy showed similarities between the fracture surfaces of ballistic fragments at the edges of the tile and biaxial fragments; this suggests a relationship between quasi-static and ballistic fragments created away from the centre of impact, although additional research will be required to determine the reason for this. Ballistic event-induced porosity was observed and quantified on the fracture surfaces of silicon carbide samples, which decreased as distance from centre of impact increased; upon further analysis this porosity was linked to the loss of a boron-rich second phase. Investigating why these inclusions are lost and the extent of the effect of this on ballistic behaviour may have important implications for the use of multi-phase ceramic materials as armour.

Atmospheric Entry Studies for Venus Missions: 45 Sphere-Cone Rigid Aeroshells and Ballistic Entries

NASA Technical Reports Server (NTRS)

Prabhu, Dinesh K.; Spilker, Thomas R.; Allen, Gary A., Jr.; Hwang, Helen H.; Cappuccio, Gelsomina; Moses, Robert W.

2013-01-01

The present study considers direct ballistic entries into the atmosphere of Venus using a 45deg sphere-cone rigid aeroshell, a legacy shape that has been used successfully in the past in the Pioneer Venus Multiprobe Mission. For a number of entry mass and heatshield diameter combinations (i.e., various ballistic coefficients) and entry velocities, the trajectory space in terms of entry flight path angles between skip out and -30deg is explored with a 3DoF trajectory code, TRAJ. From these trajectories, the viable entry flight path angle space is determined through the use of mechanical and thermal performance limits on the thermal protection material and science payload; the thermal protection material of choice is entry-grade carbon phenolic, for which a material thermal response model is available. For mechanical performance, a 200 g limit is placed on the peak deceleration load experienced by the science instruments, and 10 bar is assumed as the pressure limit for entry-grade carbon-phenolic material. For thermal performance, inflection points in the total heat load distribution are used as cut off criteria. Analysis of the results shows the existence of a range of critical ballistic coefficients beyond which the steepest possible entries are determined by the pressure limit of the material rather than the deceleration load limit.

Fast calculation of low altitude disturbing gravity for ballistics

NASA Astrophysics Data System (ADS)

Wang, Jianqiang; Wang, Fanghao; Tian, Shasha

2018-03-01

Fast calculation of disturbing gravity is a key technology in ballistics while spherical cap harmonic(SCH) theory can be used to solve this problem. By using adjusted spherical cap harmonic(ASCH) methods, the spherical cap coordinates are projected into a global coordinates, then the non-integer associated Legendre functions(ALF) of SCH are replaced by integer ALF of spherical harmonics(SH). This new method is called virtual spherical harmonics(VSH) and some numerical experiment were done to test the effect of VSH. The results of earth's gravity model were set as the theoretical observation, and the model of regional gravity field was constructed by the new method. Simulation results show that the approximated errors are less than 5mGal in the low altitude range of the central region. In addition, numerical experiments were conducted to compare the calculation speed of SH model, SCH model and VSH model, and the results show that the calculation speed of the VSH model is raised one order magnitude in a small scope.

Reconstruction of the 2014 eruption sequence of Ontake Volcano from recorded images and interviews

NASA Astrophysics Data System (ADS)

Oikawa, Teruki; Yoshimoto, Mitsuhiro; Nakada, Setsuya; Maeno, Fukashi; Komori, Jiro; Shimano, Taketo; Takeshita, Yoshihiro; Ishizuka, Yoshihiro; Ishimine, Yasuhiro

2016-05-01

A phreatic eruption at Mount Ontake (3067 m) on September 27, 2014, led to 64 casualties, including missing people. In this paper, we clarify the eruption sequence of the 2014 eruption from recorded images (photographs and videos obtained by climbers) and interviews with mountain guides and workers in mountain huts. The onset of eruption was sudden, without any clear precursory surface phenomena (such as ground rumbling or strong smell of sulfide). Our data indicate that the eruption sequence can be divided into three phases. Phase 1: The eruption started with dry pyroclastic density currents (PDCs) caused by ash column collapse. The PDCs flowed down 2.5 km SW and 2 km NW from the craters. In addition, PDCs moved horizontally by approximately 1.5 km toward N and E beyond summit ridges. The temperature of PDCs at the summit area partially exceeded 100 °C, and an analysis of interview results suggested that the temperature of PDCs was mostly in the range of 30-100 °C. At the summit area, there were violent falling ballistic rocks. Phase 2: When the outflow of PDCs stopped, the altitude of the eruption column increased; tephra with muddy rain started to fall; and ambient air temperature decreased. Falling ballistic rocks were almost absent during this phase. Phase 3: Finally, muddy hot water flowed out from the craters. These models reconstructed from observations are consistent with the phreatic eruption models and typical eruption sequences recorded at similar volcanoes.

How animals move along? Exactly solvable model of superdiffusive spread resulting from animal's decision making.

PubMed

Tilles, Paulo F C; Petrovskii, Sergei V

2016-07-01

Patterns of individual animal movement have been a focus of considerable attention recently. Of particular interest is a question how different macroscopic properties of animal dispersal result from the stochastic processes occurring on the microscale of the individual behavior. In this paper, we perform a comprehensive analytical study of a model where the animal changes the movement velocity as a result of its behavioral response to environmental stochasticity. The stochasticity is assumed to manifest itself through certain signals, and the animal modifies its velocity as a response to the signals. We consider two different cases, i.e. where the change in the velocity is or is not correlated to its current value. We show that in both cases the early, transient stage of the animal movement is super-diffusive, i.e. ballistic. The large-time asymptotic behavior appears to be diffusive in the uncorrelated case but super-ballistic in the correlated case. We also calculate analytically the dispersal kernel of the movement and show that, whilst it converge to a normal distribution in the large-time limit, it possesses a fatter tail during the transient stage, i.e. at early and intermediate time. Since the transients are known to be highly relevant in ecology, our findings may indicate that the fat tails and superdiffusive spread that are sometimes observed in the movement data may be a feature of the transitional dynamics rather than an inherent property of the animal movement.

Intracranial Pressure Response to Non-Penetrating Ballistic Impact: An Experimental Study Using a Pig Physical Head Model and Live Pigs

PubMed Central

Liu, Hai; Kang, Jianyi; Chen, Jing; Li, Guanhua; Li, Xiaoxia; Wang, Jianmin

2012-01-01

This study was conducted to characterize the intracranial pressure response to non-penetrating ballistic impact using a "scalp-skull-brain" pig physical head model and live pigs. Forty-eight ballistic tests targeting the physical head model and anesthetized pigs protected by aramid plates were conducted with standard 9 mm bullets at low (279-297 m/s), moderate (350-372 m/s), and high (409-436 m/s) velocities. Intracranial pressure responses were recorded with pressure sensors embedded in similar brain locations in the physical head model and the anesthetized pigs. Three parameters of intracranial pressure were determined from the measured data: intracranial maximum pressure (Pmax), intracranial maximum pressure impulse (PImax), and the duration of the first positive phase (PPD). The intracranial pressure waves exhibited blast-like characteristics for both the physical model and l live pigs. Of all three parameters, Pmax is most sensitive to impact velocity, with means of 126 kPa (219 kPa), 178 kPa (474 kPa), and 241 kPa (751 kPa) for the physical model (live pigs) for low, moderate, and high impact velocities, respectively. The mean PPD becomes increasingly short as the impact velocity increases, whereas PImax shows the opposite trend. Although the pressure parameters of the physical model were much lower than those of the live pigs, good correlations between the physical model and the live pigs for the three pressure parameters, especially Pmax, were found using linear regression. This investigation suggests that Pmax is a preferred parameter for predicting the severity of the brain injury resulting from behind armor blunt trauma (BABT). PMID:23055817

Point of impact: the effect of size and speed on puncture mechanics

PubMed Central

Anderson, P. S. L.; LaCosse, J.; Pankow, M.

2016-01-01

The use of high-speed puncture mechanics for prey capture has been documented across a wide range of organisms, including vertebrates, arthropods, molluscs and cnidarians. These examples span four phyla and seven orders of magnitude difference in size. The commonality of these puncture systems offers an opportunity to explore how organisms at different scales and with different materials, morphologies and kinematics perform the same basic function. However, there is currently no framework for combining kinematic performance with cutting mechanics in biological puncture systems. Our aim here is to establish this framework by examining the effects of size and velocity in a series of controlled ballistic puncture experiments. Arrows of identical shape but varying in mass and speed were shot into cubes of ballistic gelatine. Results from high-speed videography show that projectile velocity can alter how the target gel responds to cutting. Mixed models comparing kinematic variables and puncture patterns indicate that the kinetic energy of a projectile is a better predictor of penetration than either momentum or velocity. These results form a foundation for studying the effects of impact on biological puncture, opening the door for future work to explore the influence of morphology and material organization on high-speed cutting dynamics. PMID:27274801

Dissociation between behavior and motor cortical excitability before and during ballistic wrist flexion and extension in young and old adults.

PubMed

Hortobágyi, Tibor; Mieras, Adinda; Rothwell, John; Del Olmo, Miguel Fernandez

2017-01-01

Aging is associated with slow reactive movement generation and poor termination. We examined the hypothesis that the build-up of excitability in the primary motor cortex in the agonist muscle to generate ballistic wrist flexion and extension and in the antagonist to stop the movement, is lower and slower in old compared with young adults. We measured the size of the motor potentials evoked (MEP) produced by transcranial magnetic stimulation (TMS), background integrated EMG (iEMG), and the MEP:iEMG ratio in healthy young (23 y, n = 14) and old adults' (73 y, n = 14) wrist flexors and extensors as they rapidly flexed or extended the wrist in response to an auditory cue. TMS was delivered at 80% of resting motor threshold randomly in 20 ms increments between 130 and 430 ms after the tone. Even though old compared to young adults executed the two wrist movements with ~23% longer movement duration and ~15% longer reaction time (both p < 0.05), the rise in MEP:iEMG ratio before the main similar in the two age groups. These data suggest that an adjustment of current models might be needed to better understand how and if age affects the build-up excitability accompanying movement generation and termination.

Ballistic Performance of Porous-Ceramic, Thermal Protection Systems

NASA Technical Reports Server (NTRS)

Miller, J. E.; Bohl, W. E.; Christiansen, Eric C.; Davis, B. A.; Foreman, C. D.

2011-01-01

Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Orbiter, and they are currently being proposed for the next generation of US manned spacecraft, Orion. These systems insulate reentry critical components of a spacecraft against the intense thermal environments of atmospheric reentry. Additionally, these materials are highly exposed to space environment hazards like solid particle impacts. This paper discusses impact studies up to 10 km/s on 8 lb/cu ft alumina-fiber-enhanced-thermal-barrier (AETB8) tiles coated with a toughened-unipiece-fibrous-insulation/ reaction-cured-glass layer (TUFI/RCG). A semi-empirical, first principals impact model that describes projectile dispersion is described that provides excellent agreement with observations over a broad range of impact velocities, obliquities and projectile materials. Model extensions to look at the implications of greater than 10 GPa equation of state is also discussed. Predicted penetration probabilities for a vehicle visiting the International Space Station is 60% lower for orbital debris and 95% lower for meteoroids with this model compared to an energy scaled approach.

Ballistic Performance of Porous-Ceramic, Thermal Protection Systems

NASA Astrophysics Data System (ADS)

Miller, Joshua; Bohl, William; Christiansen, Eric; Davis, B. Alan; Foreman, Cory

2011-06-01

Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Orbiter, and they are currently being proposed for the next generation of US manned spacecraft, Orion. These systems insulate reentry critical components of a spacecraft against the intense thermal environments of atmospheric reentry. Additionally, these materials are also highly exposed to space environment hazards like solid particle impacts. This paper discusses impact testing up to 9.65 km/s on one of these systems. The materials considered are 8 lb/ft3 alumina-fiber-enhanced-thermal-barrier (AETB8) tiles coated with a toughened-unipiece-fibrous-insulation/reaction-cured-glass layer (TUFI/RCG). A semi-empirical, first principals impact model that describes projectile dispersion is described that provides excellent agreement with observations over a broad range of impact velocities, obliquities and projectile materials. A model extension to look at the implications of greater than 10 GPa equation of state measurements is also discussed. Predicted penetration probabilities for a vehicle visiting the International Space Station is 60% lower for orbital debris and 95% lower for meteoroids with this model compared to an energy scaled approach.

On the influence of particle morphology on the post-impact ballistic response of ceramic armour materials

NASA Astrophysics Data System (ADS)

Hameed, Amer; Appleby-Thomas, Gareth; Wood, David; Jaansalu, Kevin

2015-06-01

Recent studies have shown evidence that the ballistic-resistance of fragmented (comminuted) ceramics is independent of the original strength of the material. In particular, experimental investigations into the ballistic behaviour of such fragmented ceramics have indicated that this response is correlated to shattered ceramic morphology. This suggests that careful control of ceramic microstructure - and therefore failure paths - might provide a route to optimise post-impact ballistic performance, thereby enhancing multi-hit capability. In this study, building on previous in-house work, ballistic tests were conducted using pre-formed `fragmented-ceramic' analogues based around three morphologically differing (but chemically identical) alumina feedstock materials compacted into target `pucks. In an evolution of previous work, variation of target thickness provided additional insight into an apparent morphology-based contribution to ballistic response.

Spin-orbit torque in a thin film of the topological insulator Bi2Se3: Crossover from the ballistic to diffusive regime

NASA Astrophysics Data System (ADS)

Ren, Y. J.; Deng, W. Y.; Geng, H.; Shen, R.; Shao, L. B.; Sheng, L.; Xing, D. Y.

2017-12-01

The spin-orbit torque provides an efficient method for switching the direction of a magnetization by using an electric field. Owing to the spin-orbit coupling, when an electric field is applied, a nonequilibrium spin density is generated, which exerts a torque on the local magnetization. Here, we investigate the spin-orbit torque in a thin film of topological insulator \\text{Bi}2\\text{Se}3 based upon a Boltzmann equation, with proper boundary conditions, which is applicable from the ballistic regime to the diffusive regime. It is shown that due to the spin-momentum interlocking of the electron surface states, the magnitude of the field-like torque is simply in linear proportion to the longitudinal electrical current. For a fixed electric field, the spin-orbit torque is proportional to the sample length in the ballistic limit, and saturates to a constant in the diffusive limit. The dependence of the torque on the magnetization direction and exchange coupling strength is also studied. Our theory may offer useful guidance for experimental investigations of the spin-orbit torque in finite-size systems.

Cult of deterrence: A moral and strategic critique of the anti-ballistic missile treaty. Master`s thesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pringle, C.S.

1997-12-30

Ballistic missile defense is the morally and strategically superior alternative to the current system of deterrence, provided that it is responsibly implemented. Analysis of the Just War Criteria and the utilitarian justifications of deterrence present a moral obligation to pursue the alternative strategy of missile defense as a means of defending the United States. However, the Anti-Ballistic Missile (ABM) Treaty does not allow earnest pursuit of this alternative, despite recent efforts to exploit its loopholes and broaden its meaning beyond any reasonable limit. Moreover, deterrence can no longer provide the guarantee of security that it did during the Cold War.more » Offense-Defense Theory shows that revisionist states are not subject to the same calculations of effective deterrence that the Soviet Union was during that period. This strategic analysis underlies the moral evaluations and further supports missile defense. The cult of deterrence is presented as an explanation for the failure to adapt national security policy to the new international structure, as European powers failed to perceive the offense-defense balance prior to World War I. The ABM regime threatens to reproduce those same mistakes with even greater consequences.« less

Thermodynamic Bounds on Precision in Ballistic Multiterminal Transport

NASA Astrophysics Data System (ADS)

Brandner, Kay; Hanazato, Taro; Saito, Keiji

2018-03-01

For classical ballistic transport in a multiterminal geometry, we derive a universal trade-off relation between total dissipation and the precision, at which particles are extracted from individual reservoirs. Remarkably, this bound becomes significantly weaker in the presence of a magnetic field breaking time-reversal symmetry. By working out an explicit model for chiral transport enforced by a strong magnetic field, we show that our bounds are tight. Beyond the classical regime, we find that, in quantum systems far from equilibrium, the correlated exchange of particles makes it possible to exponentially reduce the thermodynamic cost of precision.

Symmetrical Josephson vortex interferometer as an advanced ballistic single-shot detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soloviev, I. I., E-mail: isol@phys.msu.ru; Lukin Scientific Research Institute of Physical Problems, 124460 Zelenograd, Moscow; Laboratory of Cryogenic Nanoelectronics, Nizhny Novgorod State Technical University n.a. R.E. Alekseev, 603950 Nizhny Novgorod

2014-11-17

We consider a ballistic detector formed in an interferometer manner which operational principle relies on Josephson vortex scattering at a measurement potential. We propose an approach to symmetrize the detector scheme and explore arising advantages in the signal-to-noise ratio and in the back-action on a measured object by means of recently presented numerical and analytical methods for modeling of a soliton scattering dynamics in the presence of thermal fluctuations. The obtained characteristics for experimentally relevant parameters reveal practical applicability of the considered schemes including possibility of coupling with standard digital rapid single flux quantum circuits.

Emerging national space launch programs: Economics and safeguards

NASA Astrophysics Data System (ADS)

Chow, Brian G.

Most ballistic missile nonproliferation studies have focused on trends in the numbers and performance of missiles and the resulting security threats. This report concentrates on the economic viability of emerging national space launch programs and the prospects for imposing effective safeguards against the use of space launch technology for military missiles. For the convenience of discussion in this report, a reference to ballistic missiles hereafter means surface-to-surface guided ballistic missiles only. Space launch vehicles (SLV's) are surface-to-space ballistic missiles, and they will be referred to explicitly as 'space launch vehicles' or 'space launchers'. Surface-to-surface unguided ballistic missiles will be referred to as 'rockets.'

The Future of the U.S. Intercontinental Ballistic Missile Force

DTIC Science & Technology

2014-01-01

42 3.7. Nevada Test Range and Surrounding Areas . . . . . . . . . . . . . . . . . . . . . 44 4.1. Solid Rocket ... Rocket Mass Ratio . . . 62 4.6. Range of an ICBM from Current Missile Bases . . . . . . . . . . . . . . . . 64 4.7. Range of an ICBM from Expanded...38 4.1. Specific Impulse of Various Rocket Propellants

Aerocapture Performance Analysis of A Venus Exploration Mission

NASA Technical Reports Server (NTRS)

Starr, Brett R.; Westhelle, Carlos H.

2005-01-01

A performance analysis of a Discovery Class Venus Exploration Mission in which aerocapture is used to capture a spacecraft into a 300km polar orbit for a two year science mission has been conducted to quantify its performance. A preliminary performance assessment determined that a high heritage 70 sphere-cone rigid aeroshell with a 0.25 lift to drag ratio has adequate control authority to provide an entry flight path angle corridor large enough for the mission s aerocapture maneuver. A 114 kilograms per square meter ballistic coefficient reference vehicle was developed from the science requirements and the preliminary assessment s heating indicators and deceleration loads. Performance analyses were conducted for the reference vehicle and for sensitivity studies on vehicle ballistic coefficient and maximum bank rate. The performance analyses used a high fidelity flight simulation within a Monte Carlo executive to define the aerocapture heating environment and deceleration loads and to determine mission success statistics. The simulation utilized the Program to Optimize Simulated Trajectories (POST) that was modified to include Venus specific atmospheric and planet models, aerodynamic characteristics, and interplanetary trajectory models. In addition to Venus specific models, an autonomous guidance system, HYPAS, and a pseudo flight controller were incorporated in the simulation. The Monte Carlo analyses incorporated a reference set of approach trajectory delivery errors, aerodynamic uncertainties, and atmospheric density variations. The reference performance analysis determined the reference vehicle achieves 100% successful capture and has a 99.87% probability of attaining the science orbit with a 90 meters per second delta V budget for post aerocapture orbital adjustments. A ballistic coefficient trade study conducted with reference uncertainties determined that the 0.25 L/D vehicle can achieve 100% successful capture with a ballistic coefficient of 228 kilograms per square meter and that the increased ballistic coefficient increases post aerocapture V budget to 134 meters per second for a 99.87% probability of attaining the science orbit. A trade study on vehicle bank rate determined that the 0.25 L/D vehicle can achieve 100% successful capture when the maximum bank rate is decreased from 30 deg/s to 20 deg/s. The decreased bank rate increases post aerocapture delta V budget to 102 meters per second for a 99.87% probability of attaining the science orbit.

A system structure for predictive relations in penetration mechanics

NASA Astrophysics Data System (ADS)

Korjack, Thomas A.

1992-02-01

The availability of a software system yielding quick numerical models to predict ballistic behavior is a requisite for any research laboratory engaged in material behavior. What is especially true about accessibility of rapid prototyping for terminal impaction is the enhancement of a system structure which will direct the specific material and impact situation towards a specific predictive model. This is of particular importance when the ranges of validity are at stake and the pertinent constraints associated with the impact are unknown. Hence, a compilation of semiempirical predictive penetration relations for various physical phenomena has been organized into a data structure for the purpose of developing a knowledge-based decision aided expert system to predict the terminal ballistic behavior of projectiles and targets. The ranges of validity and constraints of operation of each model were examined and cast into a decision tree structure to include target type, target material, projectile types, projectile materials, attack configuration, and performance or damage measures. This decision system implements many penetration relations, identifies formulas that match user-given conditions, and displays the predictive relation coincident with the match in addition to a numerical solution. The physical regimes under consideration encompass the hydrodynamic, transitional, and solid; the targets are either semi-infinite or plate, and the projectiles include kinetic and chemical energy. A preliminary databases has been constructed to allow further development of inductive and deductive reasoning techniques applied to ballistic situations involving terminal mechanics.

A brief review of strength and ballistic assessment methodologies in sport.

PubMed

McMaster, Daniel Travis; Gill, Nicholas; Cronin, John; McGuigan, Michael

2014-05-01

An athletic profile should encompass the physiological, biomechanical, anthropometric and performance measures pertinent to the athlete's sport and discipline. The measurement systems and procedures used to create these profiles are constantly evolving and becoming more precise and practical. This is a review of strength and ballistic assessment methodologies used in sport, a critique of current maximum strength [one-repetition maximum (1RM) and isometric strength] and ballistic performance (bench throw and jump capabilities) assessments for the purpose of informing practitioners and evolving current assessment methodologies. The reliability of the various maximum strength and ballistic assessment methodologies were reported in the form of intra-class correlation coefficients (ICC) and coefficient of variation (%CV). Mean percent differences (Mdiff = [/Xmethod1 - Xmethod2/ / (Xmethod1 + Xmethod2)] x 100) and effect size (ES = [Xmethod2 - Xmethod1] ÷ SDmethod1) calculations were used to assess the magnitude and spread of methodological differences for a given performance measure of the included studies. Studies were grouped and compared according to their respective performance measure and movement pattern. The various measurement systems (e.g., force plates, position transducers, accelerometers, jump mats, optical motion sensors and jump-and-reach apparatuses) and assessment procedures (i.e., warm-up strategies, loading schemes and rest periods) currently used to assess maximum isometric squat and mid-thigh pull strength (ICC > 0.95; CV < 2.0%), 1RM bench press, back squat and clean strength (ICC > 0.91; CV < 4.3%), and ballistic (vertical jump and bench throw) capabilities (ICC > 0.82; CV < 6.5%) were deemed highly reliable. The measurement systems and assessment procedures employed to assess maximum isometric strength [M(Diff) = 2-71%; effect size (ES) = 0.13-4.37], 1RM strength (M(Diff) = 1-58%; ES = 0.01-5.43), vertical jump capabilities (M(Diff) = 2-57%; ES = 0.02-4.67) and bench throw capabilities (M(Diff) = 7-27%; ES = 0.49-2.77) varied greatly, producing trivial to very large effects on these respective measures. Recreational to highly trained athletes produced maximum isometric squat and mid-thigh pull forces of 1,000-4,000 N; and 1RM bench press, back squat and power clean values of 80-180 kg, 100-260 kg and 70-140 kg, respectively. Mean and peak power production across the various loads (body mass to 60% 1RM) were between 300 and 1,500 W during the bench throw and between 1,500 and 9,000 W during the vertical jump. The large variations in maximum strength and power can be attributed to the wide range in physical characteristics between different sports and athletic disciplines, training and chronological age as well as the different measurement systems of the included studies. The reliability and validity outcomes suggest that a number of measurement systems and testing procedures can be implemented to accurately assess maximum strength and ballistic performance in recreational and elite athletes, alike. However, the reader needs to be cognisant of the inherent differences between measurement systems, as selection will inevitably affect the outcome measure. The strength and conditioning practitioner should also carefully consider the benefits and limitations of the different measurement systems, testing apparatuses, attachment sites, movement patterns (e.g., direction of movement, contraction type, depth), loading parameters (e.g., no load, single load, absolute load, relative load, incremental loading), warm-up strategies, inter-trial rest periods, dependent variables of interest (i.e., mean, peak and rate dependent variables) and data collection and processing techniques (i.e., sampling frequency, filtering and smoothing options).

Gunshot induced injuries in orthopaedic trauma research. A bibliometric analysis of the most influential literature.

PubMed

Held, M; Engelmann, E; Dunn, R; Ahmad, S S; Laubscher, M; Keel, M J B; Maqungo, S; Hoppe, S

2017-09-01

A growing burden of gunshot injuries demands evidence-based ballistic trauma management. No comprehensive systematic overview of the current knowledge is available to date. This study aims to identify and analyze the most influential publications in the field of orthopedic ballistic trauma research. All databases available in the Thomson Reuters Web of Knowledge were searched to conduct this bibliometrical study. The most cited orthopedic ballistic trauma articles published between 1950 and 2015 were identified by use of a multi-step approach. Publications with ten citations and more were analyzed for citations, journal, authorship, geographic origin, area of research, anatomical site, study type, study category, and level of evidence. Citations of the 128 included studies ranged from 113 to 10. These were published in fifty different journals between 1953 and 2011. Most publications (n=106; 83%) originated from the USA, were retrospective (n=85; 66.4%), level IV studies (n=90; 70.3%), reported on spinal gunshot injuries (n=49; 38.33%) and were published between 1980 and 2000 (n=111; 86.7%). This bibliometric study provides the first comprehensive overview of influential publications in the field of orthopedic ballistic trauma research. More prospective studies and high-quality systematic reviews are needed. Centres with a high burden of gunshot injuries from the developing world need to share their experience in form of international publications, to provide a more comprehensive picture of the global gun-related orthopedic injury burden. bibliometric analysis: level III. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Attitude determination with three-axis accelerometer for emergency atmospheric entry

NASA Technical Reports Server (NTRS)

Garcia-Llama, Eduardo (Inventor)

2012-01-01

Two algorithms are disclosed that, with the use of a 3-axis accelerometer, will be able to determine the angles of attack, sideslip and roll of a capsule-type spacecraft prior to entry (at very high altitudes, where the atmospheric density is still very low) and during entry. The invention relates to emergency situations in which no reliable attitude and attitude rate are available. Provided that the spacecraft would not attempt a guided entry without reliable attitude information, the objective of the entry system in such case would be to attempt a safe ballistic entry. A ballistic entry requires three controlled phases to be executed in sequence: First, cancel initial rates in case the spacecraft is tumbling; second, maneuver the capsule to a heat-shield-forward attitude, preferably to the trim attitude, to counteract the heat rate and heat load build up; and third, impart a ballistic bank or roll rate to null the average lift vector in order to prevent prolonged lift down situations. Being able to know the attitude, hence the attitude rate, will allow the control system (nominal or backup, automatic or manual) to cancel any initial angular rates. Also, since a heat-shield forward attitude and the trim attitude can be specified in terms of the angles of attack and sideslip, being able to determine the current attitude in terms of these angles will allow the control system to maneuver the vehicle to the desired attitude. Finally, being able to determine the roll angle will allow for the control of the roll ballistic rate during entry.

Conventional Prompt Global Strike and Long-Range Ballistic Missiles: Background and Issues

DTIC Science & Technology

2012-02-13

Ballistic Missiles Congressional Research Service Forward-Based Global Strike ( FBGS ...missiles in the CPGS program. Forward-Based Global Strike ( FBGS ) Analysts have also explored the option of deploying long-range land-based ballistic

Ballistic Missile Early Warning System Clear Air Force Station, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Ballistic Missile Early Warning System - Clear Air Force Station, Ballistic Missile Early Warning System Site II, One mile west of mile marker 293.5 on Parks Highway, 5 miles southwest of Anderson, Anderson, Denali Borough, AK

Missile Defense: Ballistic Missile Defense System Testing Delays Affect Delivery of Capabilities

DTIC Science & Technology

2016-04-28

Page 1 GAO- 16 -339R Ballistic Missile Defense 441 G St. N.W. Washington, DC 20548 April 28, 2016 Congressional Committees Missile Defense...Ballistic Missile Defense System Testing Delays Affect Delivery of Capabilities For over half a century , the Department of Defense (DOD) has been...81, § 232 (a) (2011). 2 GAO- 16 -339R Ballistic Missile Defense baselines, we analyzed the testing goals for selected elements, which are

Cloth Ballistic Vest Alters Response to Blast

DTIC Science & Technology

1988-01-01

Detrick, Frederick, MD 21701-501 ELEMENT NO. NO. NO. jACCESSION NO. 11. TITLE (include Security Classification) CLOTH BALLSISTIC VEST ALTERS RESPONSE...Suppl. ’rintd in USA Cloth Ballistic Vest Alters Response to Blast YANCY Y. PHILLIPS, M.D., THOMAS G. MUNDIE, PH.D., JOHN T. YELVERTON, M.S., AND DONALD R...RICHMOND, PH.D. Ballistic wounds have been and will remain the principal cause of casualties in combat. Cloth ballistic vests (CBV) play an

Non-Impact, Blast-Induced Mild TBI and PTSD: Concepts and Caveats

DTIC Science & Technology

2011-07-01

has been verified by wound ballistics experiments in animals and finite element simulation of blast loads on the torso. Blood surge caused by...ballistic pressure waves in animals An experimental study of wound ballistics demon- strates that a ballistic pressure wave can cause a remote injury to...surge. This hypothesis has been supported by some experimental data. A volumetric surge of blood moved through the thorax and abdomen has been observed

Heat-Transfer and Pressure Measurements from a Flight Test of the Third 1/18-Scale Model of the Titan Intercontinental Ballistic Missile up to a Mach Number of 3.86 and Reynolds Number per Foot of 23.5 x 10(exp 6) and a Comparison with Heat Transfer

NASA Technical Reports Server (NTRS)

Graham, John B., Jr.

1958-01-01

Heat-transfer and pressure measurements were obtained from a flight test of a 1/18-scale model of the Titan intercontinental ballistic missile up to a Mach number of 3.86 and Reynolds number per foot of 23.5 x 10(exp 6) and are compared with the data of two previously tested 1/18-scale models. Boundary-layer transition was observed on the nose of the model. Van Driest's theory predicted heat-transfer coefficients reasonably well for the fully laminar flow but predictions made by Van Driest's theory for turbulent flow were considerably higher than the measurements when the skin was being heated. Comparison with the flight test of two similar models shows fair repeatability of the measurements for fully laminar or turbulent flow.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Paul A.; Cooper, Candice Frances; Burnett, Damon J.

Light body armor development for the warfighter is based on trial-and-error testing of prototype designs against ballistic projectiles. Torso armor testing against blast is virtually nonexistent but necessary to ensure adequate protection against injury to the heart and lungs. In this report, we discuss the development of a high-fidelity human torso model, it's merging with the existing Sandia Human Head-Neck Model, and development of the modeling & simulation (M&S) capabilities necessary to simulate wound injury scenarios. Using the new Sandia Human Torso Model, we demonstrate the advantage of virtual simulation in the investigation of wound injury as it relates tomore » the warfighter experience. We present the results of virtual simulations of blast loading and ballistic projectile impact to the tors o with and without notional protective armor. In this manner, we demonstrate the ad vantages of applying a modeling and simulation approach to the investigation of wound injury and relative merit assessments of protective body armor without the need for trial-and-error testing.« less

Feasibility of ballistic strengthening exercises in neurologic rehabilitation.

PubMed

Williams, Gavin; Clark, Ross A; Hansson, Jessica; Paterson, Kade

2014-09-01

Conventional methods for strength training in neurologic rehabilitation are not task specific for walking. Ballistic strength training was developed to improve the functional transfer of strength training; however, no research has investigated this in neurologic populations. The aim of this pilot study was to evaluate the feasibility of applying ballistic principles to conventional leg strengthening exercises in individuals with mobility limitations as a result of neurologic injuries. Eleven individuals with neurologic injuries completed seated and reclined leg press using conventional and ballistic techniques. A 2 × 2 repeated-measures analysis of variance was used to compare power measures (peak movement height and peak velocity) between exercises and conditions. Peak jump velocity and peak jump height were greater when using the ballistic jump technique rather than the conventional concentric technique (P < 0.01). These findings suggest that when compared with conventional strengthening exercises, the incorporation of ballistic principles was associated with increased peak height and peak velocities.

Scaling properties of ballistic nano-transistors

PubMed Central

2011-01-01

Recently, we have suggested a scale-invariant model for a nano-transistor. In agreement with experiments a close-to-linear thresh-old trace was found in the calculated ID - VD-traces separating the regimes of classically allowed transport and tunneling transport. In this conference contribution, the relevant physical quantities in our model and its range of applicability are discussed in more detail. Extending the temperature range of our studies it is shown that a close-to-linear thresh-old trace results at room temperatures as well. In qualitative agreement with the experiments the ID - VG-traces for small drain voltages show thermally activated transport below the threshold gate voltage. In contrast, at large drain voltages the gate-voltage dependence is weaker. As can be expected in our relatively simple model, the theoretical drain current is larger than the experimental one by a little less than a decade. PMID:21711899

Separation of ballistic and diffusive fluorescence photons in confocal Light-Sheet Microscopy of Arabidopsis roots.

PubMed

Meinert, Tobias; Tietz, Olaf; Palme, Klaus J; Rohrbach, Alexander

2016-08-24

Image quality in light-sheet fluorescence microscopy is strongly affected by the shape of the illuminating laser beam inside embryos, plants or tissue. While the phase of Gaussian or Bessel beams propagating through thousands of cells can be partly controlled holographically, the propagation of fluorescence light to the detector is difficult to control. With each scatter process a fluorescence photon loses information necessary for the image generation. Using Arabidopsis root tips we demonstrate that ballistic and diffusive fluorescence photons can be separated by analyzing the image spectra in each plane without a priori knowledge. We introduce a theoretical model allowing to extract typical scattering parameters of the biological material. This allows to attenuate image contributions from diffusive photons and to amplify the relevant image contributions from ballistic photons through a depth dependent deconvolution. In consequence, image contrast and resolution are significantly increased and scattering artefacts are minimized especially for Bessel beams with confocal line detection.

Translation compensation and micro-Doppler extraction for precession ballistic targets with a wideband terahertz radar

NASA Astrophysics Data System (ADS)

Yang, Qi; Deng, Bin; Wang, Hongqiang; Zhang, Ye; Qin, Yuliang

2018-01-01

Imaging, classification, and recognition techniques of ballistic targets in midcourse have always been the focus of research in the radar field for military applications. However, the high velocity translation of ballistic targets will subject range profile and Doppler to translation, slope, and fold, which are especially severe in the terahertz region. Therefore, a two-step translation compensation method based on envelope alignment is presented. The rough compensation is based on the traditional envelope alignment algorithm in inverse synthetic aperture radar imaging, and the fine compensation is supported by distance fitting. Then, a wideband imaging radar system with a carrier frequency of 0.32 THz is introduced, and an experiment on a precession missile model is carried out. After translation compensation with the method proposed in this paper, the range profile and the micro-Doppler distributions unaffected by translation are obtained, providing an important foundation for the high-resolution imaging and micro-Doppler extraction of the terahertz radar.

Simultaneous source and attenuation reconstruction in SPECT using ballistic and single scattering data

NASA Astrophysics Data System (ADS)

Courdurier, M.; Monard, F.; Osses, A.; Romero, F.

2015-09-01

In medical single-photon emission computed tomography (SPECT) imaging, we seek to simultaneously obtain the internal radioactive sources and the attenuation map using not only ballistic measurements but also first-order scattering measurements and assuming a very specific scattering regime. The problem is modeled using the radiative transfer equation by means of an explicit non-linear operator that gives the ballistic and scattering measurements as a function of the radioactive source and attenuation distributions. First, by differentiating this non-linear operator we obtain a linearized inverse problem. Then, under regularity hypothesis for the source distribution and attenuation map and considering small attenuations, we rigorously prove that the linear operator is invertible and we compute its inverse explicitly. This allows proof of local uniqueness for the non-linear inverse problem. Finally, using the previous inversion result for the linear operator, we propose a new type of iterative algorithm for simultaneous source and attenuation recovery for SPECT based on the Neumann series and a Newton-Raphson algorithm.

Separation of ballistic and diffusive fluorescence photons in confocal Light-Sheet Microscopy of Arabidopsis roots

PubMed Central

Meinert, Tobias; Tietz, Olaf; Palme, Klaus J.; Rohrbach, Alexander

2016-01-01

Image quality in light-sheet fluorescence microscopy is strongly affected by the shape of the illuminating laser beam inside embryos, plants or tissue. While the phase of Gaussian or Bessel beams propagating through thousands of cells can be partly controlled holographically, the propagation of fluorescence light to the detector is difficult to control. With each scatter process a fluorescence photon loses information necessary for the image generation. Using Arabidopsis root tips we demonstrate that ballistic and diffusive fluorescence photons can be separated by analyzing the image spectra in each plane without a priori knowledge. We introduce a theoretical model allowing to extract typical scattering parameters of the biological material. This allows to attenuate image contributions from diffusive photons and to amplify the relevant image contributions from ballistic photons through a depth dependent deconvolution. In consequence, image contrast and resolution are significantly increased and scattering artefacts are minimized especially for Bessel beams with confocal line detection. PMID:27553506

Toward the azimuthal characteristics of ionospheric and seismic effects of "Chelyabinsk" meteorite fall according to the data from coherent radar, GPS, and seismic networks

NASA Astrophysics Data System (ADS)

Berngardt, O. I.; Perevalova, N. P.; Dobrynina, A. A.; Kutelev, K. A.; Shestakov, N. V.; Bakhtiarov, V. F.; Kusonsky, O. A.; Zagretdinov, R. V.; Zherebtsov, G. A.

2015-12-01

We present the results of a study of the azimuthal characteristics of ionospheric and seismic effects of the meteorite `Chelyabinsk,' based on the data from the network of GPS receivers, coherent decameter radar EKB, and network of seismic stations, located near the meteorite fall trajectory. It is shown that 6-14 min after the bolide explosion, GPS network observed the cone-shaped wavefront of traveling ionospheric disturbances (TIDs) that is interpreted as a ballistic acoustic wave. The typical TIDs propagation velocity were observed 661 ± 256 m/s, which corresponds to the expected acoustic wave speed for 240 km height. Fourteen minutes after the bolide explosion, at distances of 200 km, we observed the emergence and propagation of a TID with annular wavefront that is interpreted as gravitational mode of internal atmospheric waves. The propagation velocity of this TID was 337 ± 89 m/s which corresponds to the propagation velocity of these waves in similar situations. At EKB radar, we observed TIDs in the sector of azimuthal angles close to the perpendicular to the meteorite trajectory. The observed TID velocity (400 m/s) and azimuthal properties correlate well with the model of ballistic wave propagating at 120-140 km altitude. It is shown that the azimuthal distribution of the amplitude of vertical seismic oscillations with periods 3-60 s can be described qualitatively by the model of vertical strike-slip rupture, propagating at 1 km/s along the meteorite fall trajectory to distance of about 40 km. These parameters correspond to the direction and velocity of propagation of the ballistic wave peak by the ground. It is shown that the model of ballistic wave caused by supersonic motion and burning of the meteorite in the upper atmosphere can satisfactorily explain the various azimuthal ionospheric effects, observed by the coherent decameter radar EKB, GPS receivers network, and the azimuthal characteristics of seismic waves at large distances.

Conventional Prompt Global Strike and Long-Range Ballistic Missiles: Background and Issues

DTIC Science & Technology

2013-01-10

and Long-Range Ballistic Missiles Congressional Research Service Forward-Based Global Strike ( FBGS ...they may address the nuclear ambiguity issues raised by long-range ballistic missiles in the CPGS program. Forward-Based Global Strike ( FBGS

The Effects of Ballistic and Non-Ballistic Bench Press on Mechanical Variables.

PubMed

Moir, Gavin L; Munford, Shawn N; Moroski, Lindsey L; Davis, Shala E

2017-02-21

To investigate the effects of ballistic and non-ballistic bench press performed with loads equivalent to 30 and 90% 1-repetition maximum (1-RM) on mechanical variables. Eleven resistance-trained men (age: 23.0 ± 1.4 years; mass: 98.4 ± 14.4 kg) attended four testing sessions where they performed one of the following sessions: 1) three sets of five non-ballistic repetitions performed with a load equivalent to 30% 1-RM (30N-B), 2) three sets of five ballistic repetitions performed with a load equivalent to 30% 1-RM (30B), 3) three sets of four non-ballistic repetitions with a load equivalent to 90% 1-RM (90N-B), 4) three sets of four ballistic repetitions with a load equivalent to 90% 1-RM (90B). Force plates and a 3-D motion analysis system were used to determine the velocity, force, power output (PO) and work during each repetition. The heavier loads resulted in significantly greater forces applied to the barbell (mean differences: 472-783 N, p<0.001), but lower barbell velocities (mean differences: 0.85-1.20 m/s, p<0.001) and PO (mean differences: 118-492 W, p≤0.022). The ballistic conditions enhanced the mechanical variables only at the lower load with 30B producing significantly greater force (mean difference: 263 N, p<0.001), velocity (mean difference: 0.33 m/s, p<0.001), and PO (mean difference: 335 W, p<0.001) compared to 30N-B. Furthermore, the increase in PO across the 3 sets in 30B was significantly different from all other conditions (p=0.013). The total mechanical work performed was significantly greater for the conditions with the heavier loads compared to those with the lighter loads (mean differences: 3,62-5,600 J, p<0.001) and that performed during the ballistic conditions was significantly greater than that performed during the non-ballistic conditions with the same load (mean differences: 945-1,030 J, p<0.001). Ballistic bench press may be an effective exercise for developing power output and multiple sets may elicit post-activation potentiation that enhances force production. However, these benefits may be negated at heavier loads.

Improving Fermi Orbit Determination and Prediction in an Uncertain Atmospheric Drag Environment

NASA Technical Reports Server (NTRS)

Vavrina, Matthew A.; Newman, Clark P.; Slojkowski, Steven E.; Carpenter, J. Russell

2014-01-01

Orbit determination and prediction of the Fermi Gamma-ray Space Telescope trajectory is strongly impacted by the unpredictability and variability of atmospheric density and the spacecraft's ballistic coefficient. Operationally, Global Positioning System point solutions are processed with an extended Kalman filter for orbit determination, and predictions are generated for conjunction assessment with secondary objects. When these predictions are compared to Joint Space Operations Center radar-based solutions, the close approach distance between the two predictions can greatly differ ahead of the conjunction. This work explores strategies for improving prediction accuracy and helps to explain the prediction disparities. Namely, a tuning analysis is performed to determine atmospheric drag modeling and filter parameters that can improve orbit determination as well as prediction accuracy. A 45% improvement in three-day prediction accuracy is realized by tuning the ballistic coefficient and atmospheric density stochastic models, measurement frequency, and other modeling and filter parameters.

Sagnac effect and Ritz ballistic hypothesis (Review)

NASA Astrophysics Data System (ADS)

Malykin, G. B.

2010-12-01

It is shown that the Ritz ballistic hypothesis, which is based on the vector summation of the speed of light with the velocity of the radiation source, contradicts the fact of existence of the Sagnac effect. Based on a particular example of a three-mirror ring interferometer, it is shown that the application of the Ritz ballistic hypothesis leads to an obvious calculation error, namely, to the appearance of a difference in the propagation times of counterpropagating waves in the absence of rotation. A review is given of experiments and of results of processing of astronomical observations and discussions devoted to testing the Ritz ballistic hypothesis. A number of other physical phenomena that refute the Ritz ballistic hypothesis are considered.

Assessment and monitoring of ballistic and maximal upper-body strength qualities in athletes.

PubMed

Young, Kieran P; Haff, G Gregory; Newton, Robert U; Gabbett, Tim J; Sheppard, Jeremy M

2015-03-01

To evaluate whether the dynamic strength index (DSI: ballistic peak force/isometric peak force) could be effectively used to guide specific training interventions and detect training-induced changes in maximal and ballistic strength. Twenty-four elite male athletes were assessed in the isometric bench press and a 45% 1-repetition-maximum (1RM) ballistic bench throw using a force plate and linear position transducer. The DSI was calculated using the peak force values obtained during the ballistic bench throw and isometric bench press. Athletes were then allocated into 2 groups as matched pairs based on their DSI and strength in the 1RM bench press. Over the 5 wk of training, athletes performed either high-load (80-100% 1RM) bench press or moderate-load (40-55% 1RM) ballistic bench throws. The DSI was sensitive to disparate training methods, with the bench-press group increasing isometric bench-press peak force (P=.035, 91% likely), and the ballistic-bench-throw group increasing bench-throw peak force to a greater extent (P≤.001, 83% likely). A significant increase (P≤.001, 93% likely) in the DSI was observed for both groups. The DSI can be used to guide specific training interventions and can detect training-induced changes in isometric bench-press and ballistic bench-throw peak force over periods as short as 5 wk.

On an instability exhibited by the ballistic-diffusive heat conduction model of Xu and Hu

DOE PAGES

Christov, I. C.; Jordan, P. M.

2013-11-13

We show that the constitutive relation for the thermal flux proposed by Xu & Hu (2011) admits an unconditional instability. We also highlight the difference between mathematical models containing delay and those that include relaxation effects.

Factors affecting use of ballistics gelatin in laboratory studies of bacterial contamination in projectile wounds.

PubMed

Evans, Jessica J; Bost, Aaron; Muci-Küchler, Karim H; DeVeaux, Linda C

2018-05-25

Ballistics gelatin is a common tissue surrogate used in bacterial contamination models for projectile wounds. Although these studies have demonstrated that bacteria are transferred from the surface of the gelatin to the wound track by a projectile, quantifiable results have been inconsistent and not repeatable in successive tests. In this study, five areas of a typical contamination model in which bacterial recovery or survival are affected were identified for optimization. The first was a contaminated "skin" surrogate, where the novel use of vacuum filtration of a bacterial culture and buffer onto filter paper was employed. The other possibly problematic areas of the bacterial distribution model included the determination of bacterial survival when the contamination model is dried, survival in solid and molten gelatin, and the effect of high-intensity lights used for recording high-speed video. Vacuum filtration of bacteria and buffer resulted in a consistent bacterial distribution and recovery. The use of phosphate buffer M9 (pH 7) aided in neutralizing the ballistics gelatin and improving bacterial survival in solid gelatin. Additionally, the use of high-intensity lights to record high-speed video and the use of a 42 ° C water bath to melt the gelatin were found to be bactericidal for gram-positive and gram-negative bacteria. Multiple areas of a typical contamination model in which bacterial survival may be impeded were identified, and methods were proposed to improve survival in each area. These methods may be used to optimize the results of bacterial contamination models for medical applications, such as understanding the progression of infection in penetrating wounds and to identify possible sources of contamination for forensic purposes.

Aerothermodynamic Testing of Aerocapture and Planetary Probe Geometries in Hypersonic Ballistic-Range Environments

NASA Technical Reports Server (NTRS)

Wilder, M. C.; Reda, D. C.; Bogdanoff, D. W.; Olejniczak, J.

2005-01-01

A viewgraph presentation on aerothermodynamic testing of aerocapture and planetary probe design methods in hypersonic ballistic range environments is shown. The topics include: 1) Ballistic Range Testing; 2) NASA-Ames Hypervelocity Free Flight Facility; and 3) Representative Results.

Ballistic transport in graphene grown by chemical vapor deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calado, V. E.; Goswami, S.; Xu, Q.

2014-01-13

In this letter, we report the observation of ballistic transport on micron length scales in graphene synthesised by chemical vapour deposition (CVD). Transport measurements were done on Hall bar geometries in a liquid He cryostat. Using non-local measurements, we show that electrons can be ballistically directed by a magnetic field (transverse magnetic focussing) over length scales of ∼1 μm. Comparison with atomic force microscope measurements suggests a correlation between the absence of wrinkles and the presence of ballistic transport in CVD graphene.

The experimental and numerical investigation of pistol bullet penetrating soft tissue simulant.

PubMed

Wang, Yongjuan; Shi, Xiaoning; Chen, Aijun; Xu, Cheng

2015-04-01

Gelatin, a representative simulant for soft tissue of the human body, was used to study the effects of 9 mm pistol bullet's penetration. The behavior of a bullet penetrating gelatin was quantified by the temporary cavity sizes in ballistic gelatin and the pressure values of bullet's impact. A numerical simulation model of a bullet penetrating the soft tissue simulant gelatin was built using the finite element method (FEM). The model was validated by the comparison between the numerical results and the experimental results. During a bullet penetrating ballistic gelatin, four stages were clearly observed in both the experiment and the numerical simulation: a smooth attenuation stage, a rolling stage, a full penetration stage, and a stage of expansion and contraction. The cavity evolution, equivalent stress field and the strain field in gelatin were analyzed by numerical simulation. Moreover, the effects of the bullet's impact velocities and angles of incidence on the temporary cavity in gelatin, its velocity attenuation, and its rolling angle were investigated, as well as the bullet's resistance and energy variation. The physical process and the interactive mechanism during a pistol bullet penetrating gelatin were comprehensively revealed. This may be significant for research in wound ballistics. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

The mechanics of explosive seed dispersal in orange jewelweed (Impatiens capensis)

PubMed Central

Hayashi, Marika; Feilich, Kara L.; Ellerby, David J.

2009-01-01

Explosive dehiscence ballistically disperses seeds in a number of plant species. During dehiscence, mechanical energy stored in specialized tissues is transferred to the seeds to increase their kinetic and potential energies. The resulting seed dispersal patterns have been investigated in some ballistic dispersers, but the mechanical performance of a launch mechanism of this type has not been measured. The properties of the energy storage tissue and the energy transfer efficiency of the launch mechanism were quantified in Impatiens capensis. In this species the valves forming the seed pod wall store mechanical energy. Their mass specific energy storage capacity (124 J kg−1) was comparable with that of elastin and spring steel. The energy storage capacity of the pod tissues was determined by their level of hydration, suggesting a role for turgor pressure in the energy storage mechanism. During dehiscence the valves coiled inwards, collapsing the pod and ejecting the seeds. Dehiscence took 4.2±0.4 ms (mean ±SEM, n=13). The estimated efficiency with which energy was transferred to the seeds was low (0.51±0.26%, mean ±SEM, n=13). The mean seed launch angle (17.4±5.2, mean ±SEM, n=45) fell within the range predicted by a ballistic model to maximize dispersal distance. Low ballistic dispersal efficiency or effectiveness may be characteristic of species that also utilize secondary seed dispersal mechanisms. PMID:19321647

The mechanics of explosive seed dispersal in orange jewelweed (Impatiens capensis).

PubMed

Hayashi, Marika; Feilich, Kara L; Ellerby, David J

2009-01-01

Explosive dehiscence ballistically disperses seeds in a number of plant species. During dehiscence, mechanical energy stored in specialized tissues is transferred to the seeds to increase their kinetic and potential energies. The resulting seed dispersal patterns have been investigated in some ballistic dispersers, but the mechanical performance of a launch mechanism of this type has not been measured. The properties of the energy storage tissue and the energy transfer efficiency of the launch mechanism were quantified in Impatiens capensis. In this species the valves forming the seed pod wall store mechanical energy. Their mass specific energy storage capacity (124 J kg(-1)) was comparable with that of elastin and spring steel. The energy storage capacity of the pod tissues was determined by their level of hydration, suggesting a role for turgor pressure in the energy storage mechanism. During dehiscence the valves coiled inwards, collapsing the pod and ejecting the seeds. Dehiscence took 4.2+/-0.4 ms (mean +/-SEM, n=13). The estimated efficiency with which energy was transferred to the seeds was low (0.51+/-0.26%, mean +/-SEM, n=13). The mean seed launch angle (17.4+/-5.2, mean +/-SEM, n=45) fell within the range predicted by a ballistic model to maximize dispersal distance. Low ballistic dispersal efficiency or effectiveness may be characteristic of species that also utilize secondary seed dispersal mechanisms.

Remote ballistic fractures in a gelatine model - aetiology and surgical implications

PubMed Central

2013-01-01

Background Remote ballistic femoral fractures are rare fractures reported in the literature but still debated as to their existence and, indeed, their treatment. This study aimed to prove their existence, understand how they occur and determine which ammunition provides the greatest threat. In addition, fracture patterns, soft tissue disruption and contamination were assessed to aid in treatment planning. Method We filmed 42 deer femora embedded in ballistic gelatine and shot with four different military (5.56 × 45 mm, 7.62 × 39 mm) and civilian (9 × 19 mm, .44 in.) bullets, at varying distances off the bone (0–10 cm). Results Two remote ballistic fractures occurred, both with .44 in. hollow-point bullets shot 3 cm off the bone. These fractures occurred when the leading edge of the expanding temporary cavity impacted the femur's supracondylar region, producing a wedge-shaped fracture with an undisplaced limb, deceivingly giving the appearance of a spiral fracture. No communication was seen between the fracture and permanent cavity, despite the temporary cavity encasing the fracture and stripping periosteum from its base. Conclusion These fractures occur with civilian ammunition, but cannot prove their existence with military rounds. They result from the expanding temporary cavity affecting the weakest part of the bone, creating a potentially contaminated wedge-shaped fracture, important for surgeons considering operative intervention. PMID:23721113

Report of the Defense Science Board Task Force on Future Strategic Strike Skills

DTIC Science & Technology

2006-03-01

25 Figure 11: Re - entry Systems – Critical Skills...SKILLS___________________________________________________25 Figure 9: Guidance – Critical Skills Figure 10: Re - entry Systems – Critical Skills ICBMS/BASING...ability to survive intercontinental ballistic missile re - entry and then to operate effectively thereafter, is another area where current skills are

Quantum transport in d-dimensional lattices

DOE PAGES

Manzano, Daniel; Chuang, Chern; Cao, Jianshu

2016-04-28

We show that both fermionic and bosonic uniform d-dimensional lattices can be reduced to a set of independent one-dimensional chains. This reduction leads to the expression for ballistic energy fluxes in uniform fermionic and bosonic lattices. By the use of the Jordan–Wigner transformation we can extend our analysis to spin lattices, proving the coexistence of both ballistic and non-ballistic subspaces in any dimension and for any system size. Lastly, we then relate the nature of transport to the number of excitations in the homogeneous spin lattice, indicating that a single excitation always propagates ballistically and that the non-ballistic behaviour ofmore » uniform spin lattices is a consequence of the interaction between different excitations.« less

Spin injection and transport in semiconductor and metal nanostructures

NASA Astrophysics Data System (ADS)

Zhu, Lei

In this thesis we investigate spin injection and transport in semiconductor and metal nanostructures. To overcome the limitation imposed by the low efficiency of spin injection and extraction and strict requirements for retention of spin polarization within the semiconductor, novel device structures with additional logic functionality and optimized device performance have been developed. Weak localization/antilocalization measurements and analysis are used to assess the influence of surface treatments on elastic, inelastic and spin-orbit scatterings during the electron transport within the two-dimensional electron layer at the InAs surface. Furthermore, we have used spin-valve and scanned probe microscopy measurements to investigate the influence of sulfur-based surface treatments and electrically insulating barrier layers on spin injection into, and spin transport within, the two-dimensional electron layer at the surface of p-type InAs. We also demonstrate and analyze a three-terminal, all-electrical spintronic switching device, combining charge current cancellation by appropriate device biasing and ballistic electron transport. The device yields a robust, electrically amplified spin-dependent current signal despite modest efficiency in electrical injection of spin-polarized electrons. Detailed analyses provide insight into the advantages of ballistic, as opposed to diffusive, transport in device operation, as well as scalability to smaller dimensions, and allow us to eliminate the possibility of phenomena unrelated to spin transport contributing to the observed device functionality. The influence of the device geometry on magnetoresistance of nanoscale spin-valve structures is also demonstrated and discussed. Shortcomings of the simplified one-dimensional spin diffusion model for spin valve are elucidated, with comparison of the thickness and the spin diffusion length in the nonmagnetic channel as the criterion for validity of the 1D model. Our work contributes directly to the realization of spin valve and spin transistor devices based on III-V semiconductors, and offers new opportunities to engineer the behavior of spintronic devices at the nanoscale.

Efficient thermal diode with ballistic spacer

NASA Astrophysics Data System (ADS)

Chen, Shunda; Donadio, Davide; Benenti, Giuliano; Casati, Giulio

2018-03-01

Thermal rectification is of importance not only for fundamental physics, but also for potential applications in thermal manipulations and thermal management. However, thermal rectification effect usually decays rapidly with system size. Here, we show that a mass-graded system, with two diffusive leads separated by a ballistic spacer, can exhibit large thermal rectification effect, with the rectification factor independent of system size. The underlying mechanism is explained in terms of the effective size-independent thermal gradient and the match or mismatch of the phonon bands. We also show the robustness of the thermal diode upon variation of the model's parameters. Our finding suggests a promising way for designing realistic efficient thermal diodes.

Ballistic missile precession frequency extraction based on the Viterbi & Kalman algorithm

NASA Astrophysics Data System (ADS)

Wu, Longlong; Xie, Yongjie; Xu, Daping; Ren, Li

2015-12-01

Radar Micro-Doppler signatures are of great potential for target detection, classification and recognition. In the mid-course phase, warheads flying outside the atmosphere are usually accompanied by precession. Precession may induce additional frequency modulations on the returned radar signal, which can be regarded as a unique signature and provide additional information that is complementary to existing target recognition methods. The main purpose of this paper is to establish a more actual precession model of conical ballistic missile warhead and extract the precession parameters by utilizing Viterbi & Kalman algorithm, which improving the precession frequency estimation accuracy evidently , especially in low SNR.

A Residual Mass Ballistic Testing Method to Compare Armor Materials or Components (Residual Mass Ballistic Testing Method)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benjamin Langhorst; Thomas M Lillo; Henry S Chu

2014-05-01

A statistics based ballistic test method is presented for use when comparing multiple groups of test articles of unknown relative ballistic perforation resistance. The method is intended to be more efficient than many traditional methods for research and development testing. To establish the validity of the method, it is employed in this study to compare test groups of known relative ballistic performance. Multiple groups of test articles were perforated using consistent projectiles and impact conditions. Test groups were made of rolled homogeneous armor (RHA) plates and differed in thickness. After perforation, each residual projectile was captured behind the target andmore » its mass was measured. The residual masses measured for each test group were analyzed to provide ballistic performance rankings with associated confidence levels. When compared to traditional V50 methods, the residual mass (RM) method was found to require fewer test events and be more tolerant of variations in impact conditions.« less

Desktop Manufacturing Technologies.

ERIC Educational Resources Information Center

Snyder, Mark

1991-01-01

Desktop manufacturing is the use of data from a computer-assisted design system to construct actual models of an object. Emerging processes are stereolithography, laser sintering, ballistic particle manufacturing, laminated object manufacturing, and photochemical machining. (SK)

A Congeries of Numerical Models used at the BRL

DTIC Science & Technology

1980-09-01

3701 and 4773. 92 1. TASK AREA/DISCIPLINE: Exterior ballistics. 2. MODEL NAME: Six degree of freedom trajectory model. REFERENCE(S): BRL Report...B003132L) UCRL 51179, June 1972, "KDFOC: A computer Program to Calculate Fallout from Underground and Land Surface Nuclear Explosions," (U) J. B. Know, et

Current orthopaedic treatment of ballistic injuries.

PubMed

Volgas, David A; Stannard, James P; Alonso, Jorge E

2005-03-01

The purpose of this review is to examine current orthopaedic treatment of gunshot wounds. Surgeons are increasingly confronted by gunshot wounds that occur in both military and civilian settings. Much of the published work has been from military settings. In the United States, low-energy gunshot wounds are very common, and their incidence is increasing elsewhere in the world. Current treatment and its rationale is reviewed and a systematic approach to the assessment and treatment of these injuries is offered, taking into account the entirety of the injury, rather than simply the velocity of the missile.

Impact and Penetration of Thin Aluminum 2024 Flat Panels at Oblique Angles of Incidence

NASA Technical Reports Server (NTRS)

Ruggeri, Charles R.; Revilock, Duane M.; Pereira, J. Michael; Emmerling, William; Queitzsch, Gilbert K., Jr.

2015-01-01

The U.S. Federal Aviation Administration (FAA) and the National Aeronautics and Space Administration (NASA) are actively involved in improving the predictive capabilities of transient finite element computational methods for application to safety issues involving unintended impacts on aircraft and aircraft engine structures. One aspect of this work involves the development of an improved deformation and failure model for metallic materials, known as the Tabulated Johnson-Cook model, or MAT224, which has been implemented in the LS-DYNA commercial transient finite element analysis code (LSTC Corp., Livermore, CA) (Ref. 1). In this model the yield stress is a function of strain, strain rate and temperature and the plastic failure strain is a function of the state of stress, temperature and strain rate. The failure criterion is based on the accumulation of plastic strain in an element. The model also incorporates a regularization scheme to account for the dependency of plastic failure strain on mesh size. For a given material the model requires a significant amount of testing to determine the yield stress and failure strain as a function of the three-dimensional state of stress, strain rate and temperature. In addition, experiments are required to validate the model. Currently the model has been developed for Aluminum 2024 and validated against a series of ballistic impact tests on flat plates of various thicknesses (Refs. 1 to 3). Full development of the model for Titanium 6Al-4V is being completed, and mechanical testing for Inconel 718 has begun. The validation testing for the models involves ballistic impact tests using cylindrical projectiles impacting flat plates at a normal incidence (Ref. 2). By varying the thickness of the plates, different stress states and resulting failure modes are induced, providing a range of conditions over which the model can be validated. The objective of the study reported here was to provide experimental data to evaluate the model under more extreme conditions, using a projectile with a more complex shape and sharp contacts, impacting flat panels at oblique angles of incidence.

Solid Rocket Motor Combustion Instability Modeling in COMSOL Multiphysics

NASA Technical Reports Server (NTRS)

Fischbach, Sean R.

2015-01-01

Combustion instability modeling of Solid Rocket Motors (SRM) remains a topic of active research. Many rockets display violent fluctuations in pressure, velocity, and temperature originating from the complex interactions between the combustion process, acoustics, and steady-state gas dynamics. Recent advances in defining the energy transport of disturbances within steady flow-fields have been applied by combustion stability modelers to improve the analysis framework [1, 2, 3]. Employing this more accurate global energy balance requires a higher fidelity model of the SRM flow-field and acoustic mode shapes. The current industry standard analysis tool utilizes a one dimensional analysis of the time dependent fluid dynamics along with a quasi-three dimensional propellant grain regression model to determine the SRM ballistics. The code then couples with another application that calculates the eigenvalues of the one dimensional homogenous wave equation. The mean flow parameters and acoustic normal modes are coupled to evaluate the stability theory developed and popularized by Culick [4, 5]. The assumption of a linear, non-dissipative wave in a quiescent fluid remains valid while acoustic amplitudes are small and local gas velocities stay below Mach 0.2. The current study employs the COMSOL multiphysics finite element framework to model the steady flow-field parameters and acoustic normal modes of a generic SRM. The study requires one way coupling of the CFD High Mach Number Flow (HMNF) and mathematics module. The HMNF module evaluates the gas flow inside of a SRM using St. Robert's law to model the solid propellant burn rate, no slip boundary conditions, and the hybrid outflow condition. Results from the HMNF model are verified by comparing the pertinent ballistics parameters with the industry standard code outputs (i.e. pressure drop, thrust, ect.). These results are then used by the coefficient form of the mathematics module to determine the complex eigenvalues of the Acoustic Velocity Potential Equation (AVPE). The mathematics model is truncated at the nozzle sonic line, where a zero flux boundary condition is self-satisfying. The remaining boundaries are modeled with a zero flux boundary condition, assuming zero acoustic absorption on all surfaces. The results of the steady-state CFD and AVPE analyses are used to calculate the linear acoustic growth rate as is defined by Flandro and Jacob [2, 3]. In order to verify the process implemented within COMSOL we first employ the Culick theory and compare the results with the industry standard. After the process is verified, the Flandro/Jacob energy balance theory is employed and results displayed.

Defense AT and L Magazine. Vol. 46, no. 3, May-June 2017

DTIC Science & Technology

2017-05-01

rated lithium - ion rechargeable batteries , providing 150 Watt hours for up to 36 hours at a weight of 1.18 kilograms (2.6 pounds), are built in a...and post- lithium batteries , might meet or exceed the current government requirement. There are obvi- ous technical performance objectives in this...rechargeable batteries to power the technology that dismounted troops carry into battle. A quick summary of the current, proven technology is that ballistic

Ballistic limit regression analysis for Space Station Freedom meteoroid and space debris protection system

NASA Technical Reports Server (NTRS)

Jolly, William H.

1992-01-01

Relationships defining the ballistic limit of Space Station Freedom's (SSF) dual wall protection systems have been determined. These functions were regressed from empirical data found in Marshall Space Flight Center's (MSFC) Hypervelocity Impact Testing Summary (HITS) for the velocity range between three and seven kilometers per second. A stepwise linear least squares regression was used to determine the coefficients of several expressions that define a ballistic limit surface. Using statistical significance indicators and graphical comparisons to other limit curves, a final set of expressions is recommended for potential use in Probability of No Critical Flaw (PNCF) calculations for Space Station. The three equations listed below represent the mean curves for normal, 45 degree, and 65 degree obliquity ballistic limits, respectively, for a dual wall protection system consisting of a thin 6061-T6 aluminum bumper spaced 4.0 inches from a .125 inches thick 2219-T87 rear wall with multiple layer thermal insulation installed between the two walls. Normal obliquity is d(sub c) = 1.0514 v(exp 0.2983 t(sub 1)(exp 0.5228). Forty-five degree obliquity is d(sub c) = 0.8591 v(exp 0.0428) t(sub 1)(exp 0.2063). Sixty-five degree obliquity is d(sub c) = 0.2824 v(exp 0.1986) t(sub 1)(exp -0.3874). Plots of these curves are provided. A sensitivity study on the effects of using these new equations in the probability of no critical flaw analysis indicated a negligible increase in the performance of the dual wall protection system for SSF over the current baseline. The magnitude of the increase was 0.17 percent over 25 years on the MB-7 configuration run with the Bumper II program code.

The reference ballistic imaging database revisited.

PubMed

De Ceuster, Jan; Dujardin, Sylvain

2015-03-01

A reference ballistic image database (RBID) contains images of cartridge cases fired in firearms that are in circulation: a ballistic fingerprint database. The performance of an RBID was investigated a decade ago by De Kinder et al. using IBIS(®) Heritage™ technology. The results of that study were published in this journal, issue 214. Since then, technologies have evolved quite significantly and novel apparatus have become available on the market. The current research article investigates the efficiency of another automated ballistic imaging system, Evofinder(®) using the same database as used by De Kinder et al. The results demonstrate a significant increase in correlation efficiency: 38% of all matches were on first position of the Evofinder correlation list in comparison to IBIS(®) Heritage™ where only 19% were on the first position. Average correlation times are comparable to the IBIS(®) Heritage™ system. While Evofinder(®) demonstrates specific improvement for mutually correlating different ammunition brands, ammunition dependence of the markings is still strongly influencing the correlation result because the markings may vary considerably. As a consequence a great deal of potential hits (36%) was still far down in the correlation lists (positions 31 and lower). The large database was used to examine the probability of finding a match as a function of correlation list verification. As an example, the RBID study on Evofinder(®) demonstrates that to find at least 90% of all potential matches, at least 43% of the items in the database need to be compared on screen and this for breech face markings and firing pin impression separately. These results, although a clear improvement to the original RBID study, indicate that the implementation of such a database should still not be considered nowadays. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Shooting with sound: optimizing an affordable ballistic gelatin recipe in a graded ultrasound phantom education program.

PubMed

Tanious, Shariff F; Cline, Jamie; Cavin, Jennifer; Davidson, Nathan; Coleman, J Keegan; Goodmurphy, Craig W

2015-06-01

The goal of this study was to investigate the durability and longevity of gelatin formulas for the production of staged ultrasound phantoms for education. Gelatin phantoms were prepared from Knox gelatin (Kraft Foods, Northfield, IL) and a standard 10%-by-mass ordinance gelatin solution. Phantoms were durability tested by compressing to a 2-cm depth until cracking was visible. Additionally, 16 containers with varying combinations of phenol, container type, and storage location were tested for longevity against desiccation and molding. Once formulation was determined, 4 stages of phantoms from novice to clinically relevant were poured, and clinicians with ultrasound training ranked them on a 7-point Likert scale based on task difficulty, phantom suitability, and fidelity. On durability testing, the ballistic gelatin outperformed the Knox gelatin by more than 200 compressions. On longevity testing, gelatin with a 0.5% phenol concentration stored with a lid and refrigeration lasted longest, whereas containers without a lid had desiccation within 1 month, and those without phenol became moldy within 6 weeks. Ballistic gelatin was more expensive when buying in small quantities but was 7.4% less expensive when buying in bulk. The staged phantoms were deemed suitable for training, but clinicians did not consistently rank the phantoms in the intended order of 1 to 4 (44%). Refrigerated and sealed ballistic gelatin with phenol was a cost-effective method for creating in-house staged ultrasound phantoms suitable for large-scale ultrasound educational training needs. Clinician ranking of phantoms may be influenced by current training methods that favor biological tissue scanning as easier. © 2015 by the American Institute of Ultrasound in Medicine.

Ballistic limit regression analysis for Space Station Freedom meteoroid and space debris protection system

NASA Astrophysics Data System (ADS)

Jolly, William H.

1992-05-01

Relationships defining the ballistic limit of Space Station Freedom's (SSF) dual wall protection systems have been determined. These functions were regressed from empirical data found in Marshall Space Flight Center's (MSFC) Hypervelocity Impact Testing Summary (HITS) for the velocity range between three and seven kilometers per second. A stepwise linear least squares regression was used to determine the coefficients of several expressions that define a ballistic limit surface. Using statistical significance indicators and graphical comparisons to other limit curves, a final set of expressions is recommended for potential use in Probability of No Critical Flaw (PNCF) calculations for Space Station. The three equations listed below represent the mean curves for normal, 45 degree, and 65 degree obliquity ballistic limits, respectively, for a dual wall protection system consisting of a thin 6061-T6 aluminum bumper spaced 4.0 inches from a .125 inches thick 2219-T87 rear wall with multiple layer thermal insulation installed between the two walls. Normal obliquity is d(sub c) = 1.0514 v(exp 0.2983 t(sub 1)(exp 0.5228). Forty-five degree obliquity is d(sub c) = 0.8591 v(exp 0.0428) t(sub 1)(exp 0.2063). Sixty-five degree obliquity is d(sub c) = 0.2824 v(exp 0.1986) t(sub 1)(exp -0.3874). Plots of these curves are provided. A sensitivity study on the effects of using these new equations in the probability of no critical flaw analysis indicated a negligible increase in the performance of the dual wall protection system for SSF over the current baseline. The magnitude of the increase was 0.17 percent over 25 years on the MB-7 configuration run with the Bumper II program code.

Gunshot-induced fractures of the extremities: a review of antibiotic and debridement practices.

PubMed

Sathiyakumar, Vasanth; Thakore, Rachel V; Stinner, Daniel J; Obremskey, William T; Ficke, James R; Sethi, Manish K

2015-09-01

The use of antibiotic prophylaxis and debridement is controversial when treating low- and high-velocity gunshot-induced fractures, and established treatment guidelines are currently unavailable. The purpose of this review was to evaluate the literature for the prophylactic antibiotic and debridement policies for (1) low-velocity gunshot fractures of the extremities, joints, and pelvis and (2) high-velocity gunshot fractures of the extremities. Low-velocity gunshot fractures of the extremities were subcategorized into operative and non-operative cases, whereas low-velocity gunshot fractures of the joints and pelvis were evaluated based on the presence or absence of concomitant bowel injury. In the absence of surgical necessity for fracture care such as concomitant absence of gross wound contamination, vascular injury, large soft-tissue defect, or associated compartment syndrome, the literature suggests that superficial debridement for low-velocity ballistic fractures with administration of antibiotics is a satisfactory alternative to extensive operative irrigation and debridement. In operative cases or those involving bowel injuries secondary to pelvic fractures, the literature provides support for and against extensive debridement but does suggest the use of intravenous antibiotics. For high-velocity ballistic injuries, the literature points towards the practice of extensive immediate debridement with prophylactic intravenous antibiotics. Our systematic review demonstrates weak evidence for superficial debridement of low-velocity ballistic fractures, extensive debridement for high-velocity ballistic injuries, and antibiotic use for both types of injury. Intra-articular fractures seem to warrant debridement, while pelvic fractures with bowel injury have conflicting evidence for debridement but stronger evidence for antibiotic use. Given a relatively low number of studies on this subject, we recommend that further high-quality research on the debridement and antibiotic use for gunshot-induced fractures of the extremities should be conducted before definitive recommendations and guidelines are developed.

Signatures of evanescent transport in ballistic suspended graphene-superconductor junctions

PubMed Central

Kumaravadivel, Piranavan; Du, Xu

2016-01-01

In Dirac materials, the low energy excitations behave like ultra-relativistic massless particles with linear energy dispersion. A particularly intriguing phenomenon arises with the intrinsic charge transport behavior at the Dirac point where the charge density approaches zero. In graphene, a 2-D Dirac fermion gas system, it was predicted that charge transport near the Dirac point is carried by evanescent modes, resulting in unconventional “pseudo-diffusive” charge transport even in the absence of disorder. In the past decade, experimental observation of this phenomenon remained challenging due to the presence of strong disorder in graphene devices which limits the accessibility of the low carrier density regime close enough to the Dirac point. Here we report transport measurements on ballistic suspended graphene-Niobium Josephson weak links that demonstrate a transition from ballistic to pseudo-diffusive like evanescent transport below a carrier density of ~1010 cm−2. Approaching the Dirac point, the sub-harmonic gap structures due to multiple Andreev reflections display a strong Fermi energy-dependence and become increasingly pronounced, while the normalized excess current through the superconductor-graphene interface decreases sharply. Our observations are in qualitative agreement with the long standing theoretical prediction for the emergence of evanescent transport mediated pseudo-diffusive transport in graphene. PMID:27080733

Ballistic Impact Testing of Aluminum 2024 and Titanium 6Al-4V for Material Model Development

NASA Technical Reports Server (NTRS)

Pereira, J. Michael; Revilock, Duane M.; Ruggeri, Charles R.; Emmerling, William C.; Altobelli, Donald J.

2012-01-01

An experimental program is underway to develop a consistent set of material property and impact test data, and failure analysis, for a variety of materials that can be used to develop improved impact failure and deformation models. Unique features of this set of data are that all material property information and impact test results are obtained using identical materials, the test methods and procedures are extensively documented and all of the raw data is available. This report describes ballistic impact testing which has been conducted on aluminum (Al) 2024 and titanium (Ti) 6Al-4vanadium (V) sheet and plate samples of different thicknesses and with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade.

Internal ballistics of the detonation products of a blast-hole charge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mangush, S.K.; Garbunov, V.A.

1986-07-01

The authors investigate the gasdynamic flow of the detonation products of a blast-hole charge (the expansion of the detonation products in the blast hole and the gas outflow and propagation of shock airwaves into the face space). The problem is solved by means of a numerical program for integration of partial differential equations of one-dimensional gas-dynamics. A numerical model of the internal ballistics of a blast-hole charge is presented. In addition to the variation of the thermodynamic parameters in the blast hole, the formation of the shock wave in the face space is shown, which is the source of gasmore » ignition. Further development of the numerical model of the action of blast-hole charges is planned which will involve an analysis of a number of applied problems.« less

48 CFR 225.7016 - Restriction on Ballistic Missile Defense research, development, test, and evaluation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Restriction on Ballistic Missile Defense research, development, test, and evaluation. 225.7016 Section 225.7016 Federal Acquisition... Acquisition 225.7016 Restriction on Ballistic Missile Defense research, development, test, and evaluation. [68...

A ballistic mission to fly by Comet Halley

NASA Technical Reports Server (NTRS)

Boain, R. J.; Hastrup, R. C.

1980-01-01

The paper describes the available options, ballistic trajectory opportunities, and a preliminary reference trajectory that were selected as a basis for spacecraft design studies and programmatic planning for a Halley ballistic intercept mission in 1986. The paper also presents trajectory, performance, and navigation data which support the preliminary selection.

Ballistic Resistance of Armored Passenger Vehicles: Test Protocols and Quality Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeffrey M. Lacy; Robert E. Polk

2005-07-01

This guide establishes a test methodology for determining the overall ballistic resistance of the passenger compartment of assembled nontactical armored passenger vehicles (APVs). Because ballistic testing of every piece of every component of an armored vehicle is impractical, if not impossible, this guide describes a testing scheme based on statistical sampling of exposed component surface areas. Results from the test of the sampled points are combined to form a test score that reflects the probability of ballistic penetration into the passenger compartment of the vehicle.

Preservation and storage of prepared ballistic gelatine.

PubMed

Mattijssen, E J A T; Alberink, I; Jacobs, B; van den Boogaard, Y

2016-02-01

The use of ballistic gelatine, generally accepted as a human muscle tissue simulant in wound ballistic studies, might be improved by adding a preservative (Methyl 4-hydroxybenzoate) which inhibits microbial growth. This study shows that replacing a part of the gelatine powder by the preservative does not significantly alter the penetration depth of projectiles. Storing prepared blocks of ballistic gelatine over time decreased the penetration depth of projectiles. Storage of prepared gelatine for 4 week already showed a significant effect on the penetration depth of projectiles. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Ballistic Transport Exceeding 28 μm in CVD Grown Graphene.

PubMed

Banszerus, Luca; Schmitz, Michael; Engels, Stephan; Goldsche, Matthias; Watanabe, Kenji; Taniguchi, Takashi; Beschoten, Bernd; Stampfer, Christoph

2016-02-10

We report on ballistic transport over more than 28 μm in graphene grown by chemical vapor deposition (CVD) that is fully encapsulated in hexagonal boron nitride. The structures are fabricated by an advanced dry van-der-Waals transfer method and exhibit carrier mobilities of up to three million cm(2)/(Vs). The ballistic nature of charge transport is probed by measuring the bend resistance in cross- and square-shaped devices. Temperature-dependent measurements furthermore prove that ballistic transport is maintained exceeding 1 μm up to 200 K.

Radar signal analysis of ballistic missile with micro-motion based on time-frequency distribution

NASA Astrophysics Data System (ADS)

Wang, Jianming; Liu, Lihua; Yu, Hua

2015-12-01

The micro-motion of ballistic missile targets induces micro-Doppler modulation on the radar return signal, which is a unique feature for the warhead discrimination during flight. In order to extract the micro-Doppler feature of ballistic missile targets, time-frequency analysis is employed to process the micro-Doppler modulated time-varying radar signal. The images of time-frequency distribution (TFD) reveal the micro-Doppler modulation characteristic very well. However, there are many existing time-frequency analysis methods to generate the time-frequency distribution images, including the short-time Fourier transform (STFT), Wigner distribution (WD) and Cohen class distribution, etc. Under the background of ballistic missile defence, the paper aims at working out an effective time-frequency analysis method for ballistic missile warhead discrimination from the decoys.

Civilian casualties of Iranian cities by ballistic missile attacks during the Iraq-Iran war (1980-1988).

PubMed

Khaji, Ali; Fallahdoost, Shoaodin; Soroush, Mohammad Reza

2010-04-01

To determine the nature and extent of Iranian casualties by ballistic missile attacks during the eight years of the Iraq-Iran war. The data collected about Iraqi missile strikes on Iranian cities included the following: date and time, number and type of missiles, cities targeted, and injuries and deaths resulting from impacts of missiles in civilian areas. The data were extracted from a database that was constructed by the army staff headquarters based on daily reports of Iranian army units during the war. Over a period of eight years (1980-1988), Iraqi army fired 533 ballistic missiles at Iranian territories. From those, 414 missiles (77.7%) landed on Iranian cities. The impacts of these missiles caused the deaths of 2,312 civilians and injured 11,625 others. Three types of ballistic missiles were used: FROG-7, Scud, and Al-Hussein (a modified version of the Scud missile). Twenty-seven cities in Iran were struck by Iraqi ballistic missiles. The highest mortalities from ballistic missiles were in Dezful and Tehran. Iraqi missile attacks continued for 90 months (2,748 days). Our results point to the necessity of investigating the psychological consequences of Iraqi ballistic missile attacks among survivors in 27 Iranian cities during the eight years of the Iraq-Iran war.

Blunt Criterion trauma model for head and chest injury risk assessment of cal. 380 R and cal. 22 long blank cartridge actuated gundog retrieval devices.

PubMed

Frank, Matthias; Bockholdt, Britta; Peters, Dieter; Lange, Joern; Grossjohann, Rico; Ekkernkamp, Axel; Hinz, Peter

2011-05-20

Blunt ballistic impact trauma is a current research topic due to the widespread use of kinetic energy munitions in law enforcement. In the civilian setting, an automatic dummy launcher has recently been identified as source of blunt impact trauma. However, there is no data on the injury risk of conventional dummy launchers. It is the aim of this investigation to predict potential impact injury to the human head and chest on the basis of the Blunt Criterion which is an energy based blunt trauma model to assess vulnerability to blunt weapons, projectile impacts, and behind-armor-exposures. Based on experimentally investigated kinetic parameters, the injury risk of two commercially available gundog retrieval devices (Waidwerk Telebock, Germany; Turner Richards, United Kingdom) was assessed using the Blunt Criterion trauma model for blunt ballistic impact trauma to the head and chest. Assessing chest impact, the Blunt Criterion values for both shooting devices were higher than the critical Blunt Criterion value of 0.37, which represents a 50% risk of sustaining a thoracic skeletal injury of AIS 2 (moderate injury) or AIS 3 (serious injury). The maximum Blunt Criterion value (1.106) was higher than the Blunt Criterion value corresponding to AIS 4 (severe injury). With regard to the impact injury risk to the head, both devices surpass by far the critical Blunt Criterion value of 1.61, which represents a 50% risk of skull fracture. Highest Blunt Criterion values were measured for the Turner Richards Launcher (2.884) corresponding to a risk of skull fracture of higher than 80%. Even though the classification as non-guns by legal authorities might implicate harmlessness, the Blunt Criterion trauma model illustrates the hazardous potential of these shooting devices. The Blunt Criterion trauma model links the laboratory findings to the impact injury patterns of the head and chest that might be expected. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Shock Tunnel Studies of the Hypersonic Flowfield around the Hypervelocity Ballistic Models with Aerospikes

NASA Astrophysics Data System (ADS)

Balakalyani, G.; Saravanan, S.; Jagadeesh, G.

Reduced drag and aerodynamic heating are the two basic design requirements for any hypersonic vehicle [1]. The flowfield around an axisymmetric blunt body is characterized by a bow shockwave standing ahead of its nose. The pressure and temperature behind this shock wave are very high. This increased pressure and temperature are responsible for the high levels of drag and aerodynamic heating over the body. In the past, there have been many investigations on the use of aerospikes as a drag reduction tool. These studies on spiked bodies aim at reducing both the drag and aerodynamic heating by modifying the hypersonic flowfield ahead of the nose of the body [2]. However, most of them used very simple configurations to experimentally study the drag reduction using spikes at hypersonic speeds [3] and therefore very little experimental data is available for a realistic geometric configuration. In the present study, the standard AGARD Hypervelocity Ballistic model 1 is used as the test model. The addition of the spike to the blunt body significantly alters the flowfield ahead of the nose, leading to the formation of a low pressure conical recirculation region, thus causing a reduction in drag and wall heat flux [4]. In the present investigation, aerodynamic drag force is measured over the Hypervelocity Ballistic model-1, with and without spike, at a flow enthalpy of 1.7 MJ/kg. The experiments are carried out at a Mach number of 8 and at zero angle of attack. An internally mountable accelerometer based 3-component force balance system is used to measure the aerodynamic forces on the model. Also computational studies are carried out to complement the experiments.

Conceptual Development of a National Volcanic Hazard Model for New Zealand

NASA Astrophysics Data System (ADS)

Stirling, Mark; Bebbington, Mark; Brenna, Marco; Cronin, Shane; Christophersen, Annemarie; Deligne, Natalia; Hurst, Tony; Jolly, Art; Jolly, Gill; Kennedy, Ben; Kereszturi, Gabor; Lindsay, Jan; Neall, Vince; Procter, Jonathan; Rhoades, David; Scott, Brad; Shane, Phil; Smith, Ian; Smith, Richard; Wang, Ting; White, James D. L.; Wilson, Colin J. N.; Wilson, Tom

2017-06-01

We provide a synthesis of a workshop held in February 2016 to define the goals, challenges and next steps for developing a national probabilistic volcanic hazard model for New Zealand. The workshop involved volcanologists, statisticians, and hazards scientists from GNS Science, Massey University, University of Otago, Victoria University of Wellington, University of Auckland, and University of Canterbury. We also outline key activities that will develop the model components, define procedures for periodic update of the model, and effectively articulate the model to end-users and stakeholders. The development of a National Volcanic Hazard Model is a formidable task that will require long-term stability in terms of team effort, collaboration and resources. Development of the model in stages or editions that are modular will make the process a manageable one that progressively incorporates additional volcanic hazards over time, and additional functionalities (e.g. short-term forecasting). The first edition is likely to be limited to updating and incorporating existing ashfall hazard models, with the other hazards associated with lahar, pyroclastic density currents, lava flow, ballistics, debris avalanche, and gases/aerosols being considered in subsequent updates.

Can p-channel tunnel field-effect transistors perform as good as n-channel?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verhulst, A. S., E-mail: anne.verhulst@imec.be; Pourghaderi, M. A.; Collaert, N.

2014-07-28

We show that bulk semiconductor materials do not allow perfectly complementary p- and n-channel tunnel field-effect transistors (TFETs), due to the presence of a heavy-hole band. When tunneling in p-TFETs is oriented towards the gate-dielectric, field-induced quantum confinement results in a highest-energy subband which is heavy-hole like. In direct-bandgap IIIV materials, the most promising TFET materials, phonon-assisted tunneling to this subband degrades the subthreshold swing and leads to at least 10× smaller on-current than the desired ballistic on-current. This is demonstrated with quantum-mechanical predictions for p-TFETs with tunneling orthogonal to the gate, made out of InP, In{sub 0.53}Ga{sub 0.47}As, InAs,more » and a modified version of In{sub 0.53}Ga{sub 0.47}As with an artificially increased conduction-band density-of-states. We further show that even if the phonon-assisted current would be negligible, the build-up of a heavy-hole-based inversion layer prevents efficient ballistic tunneling, especially at low supply voltages. For p-TFET, a strongly confined n-i-p or n-p-i-p configuration is therefore recommended, as well as a tensily strained line-tunneling configuration.« less

Chamber transport for heavy ion fusion

NASA Astrophysics Data System (ADS)

Olson, Craig L.

2014-01-01

A brief review is given of research on chamber transport for HIF (heavy ion fusion) dating from the first HIF Workshop in 1976 to the present. Chamber transport modes are categorized into ballistic transport modes and channel-like modes. Four major HIF reactor studies are summarized (HIBALL-II, HYLIFE-II, Prometheus-H, OSIRIS), with emphasis on the chamber transport environment. In general, many beams are used to provide the required symmetry and to permit focusing to the required small spots. Target parameters are then discussed, with a summary of the individual heavy ion beam parameters required for HIF. The beam parameters are then classified as to their line charge density and perveance, with special emphasis on the perveance limits for radial space charge spreading, for the space charge limiting current, and for the magnetic (Alfven) limiting current. The major experiments on ballistic transport (SFFE, Sabre beamlets, GAMBLE II, NTX, NDCX) are summarized, with specific reference to the axial electron trapping limit for charge neutralization. The major experiments on channel-like transport (GAMBLE II channel, GAMBLE II self-pinch, LBNL channels, GSI channels) are discussed. The status of current research on HIF chamber transport is summarized, and the value of future NDCX-II transport experiments for the future of HIF is noted.

A stereoscopic imaging system for laser back scatter based trajectory measurement in ballistics: part 2

NASA Astrophysics Data System (ADS)

Chalupka, Uwe; Rothe, Hendrik

2012-03-01

The progress on a laser- and stereo-camera-based trajectory measurement system that we already proposed and described in recent publications is given. The system design was extended from one to two more powerful, DSP-controllable LASER systems. Experimental results of the extended system using different projectile-/weapon combinations will be shown and discussed. Automatic processing of acquired images using common 3DIP techniques was realized. Processing steps to extract trajectory segments from images as representative for the current application will be presented. Used algorithms for backward-calculation of the projectile trajectory will be shown. Verification of produced results is done against simulated trajectories, once in terms of detection robustness and once in terms of detection accuracy. Fields of use for the current system are within the ballistic domain. The first purpose is for trajectory measurement of small and middle caliber projectiles on a shooting range. Extension to big caliber projectiles as well as an application for sniper detection is imaginable, but would require further work. Beside classical RADAR, acoustic and optical projectile detection methods, the current system represents a further projectile location method under the new class of electro-optical methods that have been evolved in recent decades and that uses 3D imaging acquisition and processing techniques.

Environmentally compatible solid rocket propellants

NASA Technical Reports Server (NTRS)

Jacox, James L.; Bradford, Daniel J.

1995-01-01

Hercules' clean propellant development research is exploring three major types of clean propellant: (1) chloride-free formulations (no chlorine containing ingredients), being developed on the Clean Propellant Development and Demonstration (CPDD) contract sponsored by Phillips Laboratory, Edwards Air Force Base, CA; (2) low HCl scavenged formulations (HCl-scavenger added to propellant oxidized with ammonium perchlorate (AP)); and (3) low HCl formulations oxidized with a combination of AN and AP (with or without an HCl scavenger) to provide a significant reduction (relative to current solid rocket boosters) in exhaust HCl. These propellants provide performance approaching that of current systems, with less than 2 percent HCl in the exhaust, a significant reduction (greater than or equal to 70 percent) in exhaust HCl levels. Excellent processing, safety, and mechanical properties were achieved using only readily available, low cost ingredients. Two formulations, a sodium nitrate (NaNO3) scavenged HTPB and a chloride-free hydroxy terminated polyether (HTPE) propellant, were characterized for ballistic, mechanical, and rheological properties. In addition, the hazards properties were demonstrated to provide two families of class 1.3, 'zero-card' propellants. Further characterization is planned which includes demonstration of ballistic tailorability in subscale (one to 70 pound) motors over the range of burn rates required for retrofit into current Hercules space booster designs (Titan 4 SRMU and Delta 2 GEM).

Voyager Observations of the Color of Saturn's Ring

NASA Technical Reports Server (NTRS)

Estrada, Paul R.; Cuzzi, Jeffrey N.; Morrison, David (Technical Monitor)

1994-01-01

Previously unreduced high resolution Voyager 2 images of Saturn's main rings are used to generate reflectivity (I/F) profiles as a function of radius. Ratios of profiles taken from green, violet, orange, and UV filter images are then produced. The I/F ratios are diagnostic of composition, and provide us with information on the rings' present state of compositional evolution. The rings are extremely reddish in color which suggests that they could not be pure water ice. The most likely candidates for the non-icy components are silicates and organics. The sources of these pollutants are of extreme importance in determining the compositional history of the rings. The radial profiles of ring color ratio exhibit several very interesting properties: (a) broad-scale, fairly smooth, color variations which are only weakly correlated with underlying ring structure (optical depth variations) across the outer C ring and inner B ring as well as the Cassini division region. These variations are probably consistent with ballistic transport; (b) fine-scale, noise-Like (but unquestionably real) color variations across at least the outer two-thirds of the B ring. Not only the "redness" but the spectral shape varies. These variations are currently unexplained. Groundbased spectroscopic observations should be pursued to study the implied compositional heterogeneities on at least the larger scales. This data set will be used for modeling of the color and composition of the main rings using ballistic transport and radiative transfer theories.

Optimising ballistic facial coverage from military fragmenting munitions: a consensus statement.

PubMed

Breeze, J; Tong, D C; Powers, D; Martin, N A; Monaghan, A M; Evriviades, D; Combes, J; Lawton, G; Taylor, C; Kay, A; Baden, J; Reed, B; MacKenzie, N; Gibbons, A J; Heppell, S; Rickard, R F

2017-02-01

VIRTUS is the first United Kingdom (UK) military personal armour system to provide components that are capable of protecting the whole face from low velocity ballistic projectiles. Protection is modular, using a helmet worn with ballistic eyewear, a visor, and a mandibular guard. When all four components are worn together the face is completely covered, but the heat, discomfort, and weight may not be optimal in all types of combat. We organized a Delphi consensus group analysis with 29 military consultant surgeons from the UK, United States, Canada, Australia, and New Zealand to identify a potential hierarchy of functional facial units in order of importance that require protection. We identified the causes of those facial injuries that are hardest to reconstruct, and the most effective combinations of facial protection. Protection is required from both penetrating projectiles and burns. There was strong consensus that blunt injury to the facial skeleton was currently not a military priority. Functional units that should be prioritised are eyes and eyelids, followed consecutively by the nose, lips, and ears. Twenty-nine respondents felt that the visor was more important than the mandibular guard if only one piece was to be worn. Essential cover of the brain and eyes is achieved from all directions using a combination of helmet and visor. Nasal cover currently requires the mandibular guard unless the visor can be modified to cover it as well. Any such prototype would need extensive ergonomics and assessment of integration, as any changes would have to be acceptable to the people who wear them in the long term. Crown Copyright © 2016. Published by Elsevier Ltd. All rights reserved.

Carbon Nano-particle Synthesized by Pulsed Arc Discharge Method as a Light Emitting Device

NASA Astrophysics Data System (ADS)

Ahmadi, Ramin; Ahmadi, Mohamad Taghi; Ismail, Razali

2018-07-01

Owing to the specific properties such as high mobility, ballistic carrier transport and light emission, carbon nano-particles (CNPs) have been employed in nanotechnology applications. In the presented work, the CNPs are synthesized by using the pulsed arc discharge method between two copper electrodes. The rectifying behaviour of produced CNPs is explored by assuming an Ohmic contact between the CNPs and the electrodes. The synthesized sample is characterized by electrical investigation and modelling. The current-voltage ( I- V) relationship is investigated and bright visible light emission from the produced CNPs was measured. The electroluminescence (EL) intensity was explored by changing the distance between two electrodes. An incremental behaviour on EL by a resistance gradient and distance reduction is identified.

Carbon Nano-particle Synthesized by Pulsed Arc Discharge Method as a Light Emitting Device

NASA Astrophysics Data System (ADS)

Ahmadi, Ramin; Ahmadi, Mohamad Taghi; Ismail, Razali

2018-04-01

Owing to the specific properties such as high mobility, ballistic carrier transport and light emission, carbon nano-particles (CNPs) have been employed in nanotechnology applications. In the presented work, the CNPs are synthesized by using the pulsed arc discharge method between two copper electrodes. The rectifying behaviour of produced CNPs is explored by assuming an Ohmic contact between the CNPs and the electrodes. The synthesized sample is characterized by electrical investigation and modelling. The current-voltage (I-V) relationship is investigated and bright visible light emission from the produced CNPs was measured. The electroluminescence (EL) intensity was explored by changing the distance between two electrodes. An incremental behaviour on EL by a resistance gradient and distance reduction is identified.

A Limited Antiballistic Missile System

DTIC Science & Technology

1990-12-01

2.2 ABM Philosophy. .. .. .. .. ... ... ... ...... 2-1 2.3 Ballistic Missile Flight Phases .. .. .. .... ....... 2-3 2.4 Past US Systems...2-7 iii Page 2.4.4 SAFEGUARD .. .. .. .. .. ... ... ..... 2-8 2.4.5 Other Programs. .. .. .. .. ... ... ..... 2-9 2.5 Current ABM ...2.5.6 Summary of ABM Characteristics. .. .. ..... 2-11 2.6 The Threat .. .. .. .. ... ... ... ... ... ... 2-12 2.6.1 The Middle East

75 FR 64714 - Meeting of the Chief of Naval Operations Executive Panel

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-20

... recommendations of the Subcommittee on Navy's Role in Ballistic Missile Defense. The meeting will consist of discussions of Navy's role in ballistic missile defense, development of the global missile defense network and evolution of the growing ballistic missile threat. DATES: The meeting will be held on November 12, 2010...

Whither Ballistic Missile Defense?

DTIC Science & Technology

1992-11-30

Conference on Technical Marketing 2000: Opportunities and Strategies for a Changing World) I intend to discuss the prospects for SDI in a changing...Technical Marketing 2000: Opportunities and Strategies for a Changing World) Descriptors, Keywords: Cooper Speech Ballistic Missile Defense...WHITHER BALLISTIC MISSILE DEFENSE? BY AMBASSADOR HENRY F. COOPER NOVEMBER 30,1992 TECHNICAL MARKETING SOCIETY OF AMERICA WASHINGTON, DC

Optimization of Aimpoints for Coordinate Seeking Weapons

DTIC Science & Technology

2015-09-01

aiming) and independent ( ballistic ) errors are taken into account, before utilizing each of the three damage functions representing the weapon. A Monte...characteristics such as the radius of the circle containing the weapon aimpoint, impact angle, dependent (aiming) and independent ( ballistic ) errors are taken...Dependent (Aiming) Error .................................8 2. Single Weapon Independent ( Ballistic ) Error .............................9 3

Management of civilian ballistic fractures.

PubMed

Seng, V S; Masquelet, A C

2013-12-01

The management of ballistic fractures, which are open fractures, has often been studied in wartime and has benefited from the principles of military surgery with debridement and lavage, and the use of external fixation for bone stabilization. In civilian practice, bone stabilization of these fractures is different and is not performed by external fixation. Fifteen civilian ballistic fractures, Gustilo II or IIIa, two associated with nerve damage and none with vascular damage, were reviewed. After debridement and lavage, ten internal fixations and five conservative treatments were used. No superficial or deep surgical site infection was noted. Fourteen of the 15 fractures (93%) healed without reoperation. Eleven of the 15 patients (73%) regained normal function. Ballistic fractures have a bad reputation due to their many complications, including infections. In civilian practice, the use of internal fixation is not responsible for excessive morbidity, provided debridement and lavage are performed. Civilian ballistic fractures, when they are caused by low-velocity firearms, differ from military ballistic fractures. Although the principle of surgical debridement and lavage remains the same, bone stabilization is different and is similar to conventional open fractures. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

A simple Boltzmann transport equation for ballistic to diffusive transient heat transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maassen, Jesse, E-mail: jmaassen@purdue.edu; Lundstrom, Mark

2015-04-07

Developing simplified, but accurate, theoretical approaches to treat heat transport on all length and time scales is needed to further enable scientific insight and technology innovation. Using a simplified form of the Boltzmann transport equation (BTE), originally developed for electron transport, we demonstrate how ballistic phonon effects and finite-velocity propagation are easily and naturally captured. We show how this approach compares well to the phonon BTE, and readily handles a full phonon dispersion and energy-dependent mean-free-path. This study of transient heat transport shows (i) how fundamental temperature jumps at the contacts depend simply on the ballistic thermal resistance, (ii) thatmore » phonon transport at early times approach the ballistic limit in samples of any length, and (iii) perceived reductions in heat conduction, when ballistic effects are present, originate from reductions in temperature gradient. Importantly, this framework can be recast exactly as the Cattaneo and hyperbolic heat equations, and we discuss how the key to capturing ballistic heat effects is to use the correct physical boundary conditions.« less

Solid-propellant rocket motor internal ballistic performance variation analysis, phase 2

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Foster, W. A., Jr.

1976-01-01

The Monte Carlo method was used to investigate thrust imbalance and its first time derivative throughtout the burning time of pairs of solid rocket motors firing in parallel. Results obtained compare favorably with Titan 3 C flight performance data. Statistical correlations of the thrust imbalance at various times with corresponding nominal trace slopes suggest several alternative methods of predicting thrust imbalance. The effect of circular-perforated grain deformation on internal ballistics is discussed, and a modified design analysis computer program which permits such an evaluation is presented. Comparisons with SRM firings indicate that grain deformation may account for a portion of the so-called scale factor on burning rate between large motors and strand burners or small ballistic test motors. Thermoelastic effects on burning rate are also investigated. Burning surface temperature is calculated by coupling the solid phase energy equation containing a strain rate term with a model of gas phase combustion zone using the Zeldovich-Novozhilov technique. Comparisons of solutions with and without the strain rate term indicate a small but possibly significant effect of the thermoelastic coupling.

Effects of solid-propellant temperature gradients on the internal ballistics of the Space Shuttle

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Foster, W. A., Jr.; Shackelford, B. W., Jr.

1978-01-01

The internal ballistic effects of combined radial and circumferential grain temperature gradients are evaluated theoretically for the Space Shuttle solid rocket motors (SRMs). A simplified approach is devised for representing with closed-form mathematical expressions the temperature distribution resulting from the anticipated thermal history prior to launch. The internal ballistic effects of the gradients are established by use of a mathematical model which permits the propellant burning rate to vary circumferentially. Comparative results are presented for uniform and axisymmetric temperature distributions and the anticipated gradients based on an earlier two-dimensional analysis of the center SRM segment. The thrust imbalance potential of the booster stage is also assessed based on the difference in the thermal loading of the individual SRMs of the motor pair which may be encountered in both summer and winter environments at the launch site. Results indicate that grain temperature gradients could cause the thrust imbalance to be approximately 10% higher in the Space Shuttle than the imbalance caused by SRM manufacturing and propellant physical property variability alone.

Material characterization of a novel new armour steel

NASA Astrophysics Data System (ADS)

Bester, J. N.; Stumpf, W. E.

2012-08-01

The material characterization of a novel new armour steel with comparison to a leading commercial benchmark alloy is presented. Direct ballistic and experimental comparison is drawn. The 5.56 × 45 mm [M193] and 7.62 × 51 mm [NATO Ball] projectiles were used in a cartridge type high pressure barrel configuration to evaluate the superior plugging resistance of the new steel over a range of plate thicknesses. To characterize the dynamic plasticity of the materials, quasi-static, notched and high temperature tensile tests as well as Split Hopkinson Pressure Bar tests in tension and compression were performed. The open source explicit solver, IMPACT (sourceforge.net) is used in an ongoing numerical and sensitivity analysis of ballistic impact. A simultaneous multi variable fitting algorithm is planned to evaluate several selected numerical material models and show their relative correlation to experimental data. This study as well as micro-metallurgical investigation of adiabatic shear bands and localized deformation zones should result in new insights in to the underlying metallurgical and physical behavior of armour plate steels during ballistic perforation.

Ballistically Initiated Fire Ball Generation Using M&S: Innovation Grant (Briefing Charts)

DTIC Science & Technology

2012-01-26

isotropic in nature Phenomenological models for explosives initiation. – HVRB, forest fire etc. Equation of state – Ideal gas, Mie-Gruneisen, JWL ...perfectly plastic description • EOS • Mie Gruneisen • JWL for explosive • Phenomenological Model for EFP • High Explosive input for programmed burn

Channel length scaling behavior in transistors based on individual versus dense arrays of carbon nanotubes

NASA Astrophysics Data System (ADS)

Brady, Gerald J.; Jinkins, Katherine R.; Arnold, Michael S.

2017-09-01

Recent advances in the solution-phase sorting and assembly of semiconducting single-walled carbon nanotubes (SWCNTs) have enabled significant gains in the performance of field-effect transistors (FETs) constructed from dense arrays of aligned SWCNTs. However, the channel length (LCH) downscaling behaviors of these arrays, which contain some organizational disorder (i.e., rotational misalignment and non-uniform pitch), have not yet been studied in detail below LCH of 100 nm. This study compares the behaviors of individualized SWCNTs with arrays of aligned, solution-cast SWCNTs in FETs with LCH ranging from 30 to 240 nm. The on-state conductance of both individual and array SWCNTs rises with decreasing LCH. Nearly ballistic transport is observed for LCH < 40 nm in both cases, reaching a conductance of 0.82 Go per SWCNT in arrays, where Go = 2e2/h is the quantum conductance. In the off-state, the off-current and subthreshold swing of the individual SWCNTs remain nearly invariant with decreasing LCH whereas array SWCNT FETs suffer from increasing off-state current and deteriorating subthreshold swing for LCH below 100 nm. We analyze array disorder using atomic force microscopy, which shows that crossing SWCNTs that arise from misoriented alignment raise SWCNTs off of the substrate for large portions of the channel when LCH is small. Electrostatics modeling analysis indicates that these raised SWCNTs are a likely contributor to the deteriorating off-current and subthreshold characteristics of arrays. These results demonstrate that improved inter-SWCNT pitch uniformity and alignment with minimal inter-SWCNT interactions will be necessary in order for solution processed SWCNT arrays to reach subthreshold performance on par with isolated SWCNTs. These results are also promising because they show that arrays of solution-processed SWCNTs can nearly reach ballistic conductance in the on-state despite imperfections in pitch and alignment.

Bringing in the Reinforcements

NASA Technical Reports Server (NTRS)

2004-01-01

What do NASA and ballistics have in common? More than the average person may know. Everyday, millions of Americans drive in vehicles, cross over bridges, and fly in airplanes without knowing just how important NASA s role in studying ballistics is in making these actions viable and safe for them. At Glenn Research Center s Ballistic Impact Facility, NASA scientists and engineers study the dynamics of high-speed projectiles and their impact on targets to create materials and structures that are smarter, lighter, and stronger. By applying the science of ballistics to new developments, these researchers are taking major steps in preventing catastrophic events. The Ballistic Impact Facility s main features are a 40-foot-long gas gun that can launch projectiles at speeds over 1,000 miles per hour and highspeed cameras that can capture up to 250 million images per second.

A research study for the preliminary definition of an aerophysics free-flight laboratory facility

NASA Technical Reports Server (NTRS)

Canning, Thomas N.

1988-01-01

A renewed interest in hypervelocity vehicles requires an increase in the knowledge of aerodynamic phenomena. Tests conducted with ground-based facilities can be used both to better understand the physics of hypervelocity flight, and to calibrate and validate computer codes designed to predict vehicle performance in the hypervelocity environment. This research reviews the requirements for aerothermodynamic testing and discusses the ballistic range and its capabilities. Examples of the kinds of testing performed in typical high performance ballistic ranges are described. We draw heavily on experience obtained in the ballistics facilities at NASA Ames Research Center, Moffett Field, California. Prospects for improving the capabilities of the ballistic range by using advanced instrumentation are discussed. Finally, recent developments in gun technology and their application to extend the capability of the ballistic range are summarized.

Natural Mallow Fiber-Reinforced Epoxy Composite for Ballistic Armor Against Class III-A Ammunition

NASA Astrophysics Data System (ADS)

Nascimento, Lucio Fabio Cassiano; Holanda, Luane Isquerdo Ferreira; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Gomes, Alaelson Vieira; Lima, Édio Pereira

2017-10-01

Epoxy matrix composites reinforced with up to 30 vol pct of continuous and aligned natural mallow fibers were for the first time ballistic tested as personal armor against class III-A 9 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared to those in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout and rupture as well as epoxy cracking. As compared to Kevlar™, the mallow fiber composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes the mallow fiber composites a promising material for personal ballistic protection.

Modelling dwarf mistletoe at three scales: life history, ballistics and contagion

Treesearch

Donald C. E. Robinson; Brian W. Geils

2006-01-01

The epidemiology of dwarf mistletoe (Arceuthobium) is simulated for the reproduction, dispersal, and spatial patterns of these plant pathogens on conifer trees. A conceptual model for mistletoe spread and intensification is coded as sets of related subprograms that link to either of two individual-tree growth models (FVS and TASS) used by managers to develop...

A Novel Binarization Algorithm for Ballistics Firearm Identification

NASA Astrophysics Data System (ADS)

Li, Dongguang

The identification of ballistics specimens from imaging systems is of paramount importance in criminal investigation. Binarization plays a key role in preprocess of recognizing cartridges in the ballistic imaging systems. Unfortunately, it is very difficult to get the satisfactory binary image using existing binary algorithms. In this paper, we utilize the global and local thresholds to enhance the image binarization. Importantly, we present a novel criterion for effectively detecting edges in the images. Comprehensive experiments have been conducted over sample ballistic images. The empirical results demonstrate the proposed method can provide a better solution than existing binary algorithms.

Ballistic magnon heat conduction and possible Poiseuille flow in the helimagnetic insulator Cu2OSeO3

NASA Astrophysics Data System (ADS)

Prasai, N.; Trump, B. A.; Marcus, G. G.; Akopyan, A.; Huang, S. X.; McQueen, T. M.; Cohn, J. L.

2017-06-01

We report on the observation of magnon thermal conductivity κm˜70 W/mK near 5 K in the helimagnetic insulator Cu2OSeO3 , exceeding that measured in any other ferromagnet by almost two orders of magnitude. Ballistic, boundary-limited transport for both magnons and phonons is established below 1 K, and Poiseuille flow of magnons is proposed to explain a magnon mean-free path substantially exceeding the specimen width for the least defective specimens in the range 2 K

Forensic archaeology and anthropology : An Australian perspective.

PubMed

Oakley, Kate

2005-09-01

Forensic archaeology is an extremely powerful investigative discipline and, in combination with forensic anthropology, can provide a wealth of evidentiary information to police investigators and the forensic community. The re-emergence of forensic archaeology and anthropology within Australia relies on its diversification and cooperation with established forensic medical organizations, law enforcement forensic service divisions, and national forensic boards. This presents a unique opportunity to develop a new multidisciplinary approach to forensic archaeology/anthropology within Australia as we hold a unique set of environmental, social, and cultural conditions that diverge from overseas models and require different methodological approaches. In the current world political climate, more forensic techniques are being applied at scenes of mass disasters, genocide, and terrorism. This provides Australian forensic archaeology/anthropology with a unique opportunity to develop multidisciplinary models with contributions from psychological profiling, ballistics, sociopolitics, cultural anthropology, mortuary technicians, post-blast analysis, fire analysis, and other disciplines from the world of forensic science.

Propulsion dynamics of lunar hoppers

NASA Technical Reports Server (NTRS)

Meetin, R. J.; Seifert, H. S.

1974-01-01

A feasibility study was recently completed on a hopping transporter concept for locomotion on the moon. Termed a Lunar Pogo because it would operate similarly to a conventional pogo stick, this vehicle would accelerate up an inclined leg, pick up the leg, and then enter ballistic flight over the moon's surface. Upon recontacting the lunar surface, the Lunar Pogo would decelerate down the leg. Propulsion would be provided by expansion of gas against a piston. Operation would be partially conservative because much of the energy expended by the gas during takeoff would be recovered by compressing the gas during landing. Two models of the ballistics and propulsion have been set up to estimate performance. The simplified first-order model illuminates the thermodynamics of ideal operation. The second-order model, which includes realistic effects such as sliding, provides a better approximation to actual performance. In a one-man Lunar Pogo, an astronaut would typically make 15-m (50-ft) leaps at an average speed of 5-8 km (3-5 miles) per hour.

15 CFR 744.3 - Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch vehicles and sounding rockets) and Unmanned Air...: END-USER AND END-USE BASED § 744.3 Restrictions on Certain Rocket Systems (including ballistic missile...

15 CFR 744.3 - Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 15 Commerce and Foreign Trade 2 2011-01-01 2011-01-01 false Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch vehicles and sounding rockets) and Unmanned Air...: END-USER AND END-USE BASED § 744.3 Restrictions on Certain Rocket Systems (including ballistic missile...

15 CFR 744.3 - Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 15 Commerce and Foreign Trade 2 2013-01-01 2013-01-01 false Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch vehicles and sounding rockets) and Unmanned Air...: END-USER AND END-USE BASED § 744.3 Restrictions on Certain Rocket Systems (including ballistic missile...

15 CFR 744.3 - Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 15 Commerce and Foreign Trade 2 2014-01-01 2014-01-01 false Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch vehicles and sounding rockets) and Unmanned Air...: END-USER AND END-USE BASED § 744.3 Restrictions on Certain Rocket Systems (including ballistic missile...

15 CFR 744.3 - Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 15 Commerce and Foreign Trade 2 2012-01-01 2012-01-01 false Restrictions on Certain Rocket Systems (including ballistic missile systems and space launch vehicles and sounding rockets) and Unmanned Air...: END-USER AND END-USE BASED § 744.3 Restrictions on Certain Rocket Systems (including ballistic missile...

Effects of High-Density Impacts on Shielding Capability

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Lear, Dana M.

2014-01-01

Spacecraft are shielded from micrometeoroids and orbital debris (MMOD) impacts to meet requirements for crew safety and/or mission success. In the past, orbital debris particles have been considered to be composed entirely of aluminum (medium-density material) for the purposes of MMOD shielding design and verification. Meteoroids have been considered to be low-density porous materials, with an average density of 1 g/cu cm. Recently, NASA released a new orbital debris environment model, referred to as ORDEM 3.0, that indicates orbital debris contains a substantial fraction of high-density material for which steel is used in MMOD risk assessments [Ref.1]. Similarly, an update to the meteoroid environment model is also under consideration to include a high-density component of that environment. This paper provides results of hypervelocity impact tests and hydrocode simulations on typical spacecraft MMOD shields using steel projectiles. It was found that previous ballistic limit equations (BLEs) that define the protection capability of the MMOD shields did not predict the results from the steel impact tests and hydrocode simulations (typically, the predictions from these equations were too optimistic). The ballistic limit equations required updates to more accurately represent shield protection capability from the range of densities in the orbital debris environment. Ballistic limit equations were derived from the results of the work and are provided in the paper.

Armours for soft bodies: how far can bioinspiration take us?

PubMed

White, Zachary W; Vernerey, Franck J

2018-05-15

The development of armour is as old as the dawn of civilization. Early man looked to natural structures to harvest or replicate for protection, leaning on millennia of evolutionary developments in natural protection. Since the advent of more modern weaponry, Armor development has seemingly been driven more by materials research than bio-inspiration. However, parallels can still be drawn between modern bullet-protective armours and natural defensive structures. Soft armour for handgun and fragmentation threats can be likened to mammalian skin, and similarly, hard armour can be compared with exoskeletons and turtle shells. Via bio-inspiration, it may be possible to develop structures previously un-researched for ballistic protection. This review will cover current modern ballistic protective structures focusing on energy dissipation and absorption methods, and their natural analogues. As all armour is a compromise between weight, flexibility and protection, the imbricated structure of scaled skin will be presented as a better balance between these factors.

Wound ballistics of firearm-related injuries--part 2: mechanisms of skeletal injury and characteristics of maxillofacial ballistic trauma.

PubMed

Stefanopoulos, P K; Soupiou, O T; Pazarakiotis, V C; Filippakis, K

2015-01-01

Maxillofacial firearm-related injuries vary in extent and severity because of the characteristics and behaviour of the projectile(s), and the complexity of the anatomical structures involved, whereas the degree of tissue disruption is also affected by the distance of the shot. In low-energy injuries there is limited damage to the underlying skeleton, which usually dominates the clinical picture, dictating a more straightforward therapeutic approach. High-energy injuries are associated with extensive hard and soft tissue disruption, and are characterized by a surrounding zone of damaged tissue that is prone to progressive necrosis as a result of compromised blood supply and wound sepsis. Current treatment protocols for these injuries emphasize the importance of serial debridement for effective wound control while favouring early definitive reconstruction. Copyright © 2014 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Effects of acute static, ballistic, and PNF stretching exercise on the muscle and tendon tissue properties.

PubMed

Konrad, A; Stafilidis, S; Tilp, M

2017-10-01

The purpose of this study was to investigate the influence of a single static, ballistic, or proprioceptive neuromuscular facilitation (PNF) stretching exercise on the various muscle-tendon parameters of the lower leg and to detect possible differences in the effects between the methods. Volunteers (n = 122) were randomly divided into static, ballistic, and PNF stretching groups and a control group. Before and after the 4 × 30 s stretching intervention, we determined the maximum dorsiflexion range of motion (RoM) with the corresponding fascicle length and pennation angle of the gastrocnemius medialis. Passive resistive torque (PRT) and maximum voluntary contraction (MVC) were measured with a dynamometer. Observation of muscle-tendon junction (MTJ) displacement with ultrasound allowed us to determine the length changes in the tendon and muscle, respectively, and hence to calculate stiffness. Although RoM increased (static: +4.3%, ballistic: +4.5%, PNF: +3.5%), PRT (static: -11.4%, ballistic: -11.5%, PNF: -13,7%), muscle stiffness (static: -13.1%, ballistic: -20.3%, PNF: -20.2%), and muscle-tendon stiffness (static: -11.3%, ballistic: -10.5%, PNF: -13.7%) decreased significantly in all the stretching groups. Only in the PNF stretching group, the pennation angle in the stretched position (-4.2%) and plantar flexor MVC (-4.6%) decreased significantly. Multivariate analysis showed no clinically relevant difference between the stretching groups. The increase in RoM and the decrease in PRT and muscle-tendon stiffness could be explained by more compliant muscle tissue following a single static, ballistic, or PNF stretching exercise. © 2017 The Authors Scandinavian Journal of Medicine & Science In Sports Published by John Wiley & Sons Ltd.

Potentiation Effects of Half-Squats Performed in a Ballistic or Nonballistic Manner.

PubMed

Suchomel, Timothy J; Sato, Kimitake; DeWeese, Brad H; Ebben, William P; Stone, Michael H

2016-06-01

This study examined and compared the acute effects of ballistic and nonballistic concentric-only half-squats (COHSs) on squat jump performance. Fifteen resistance-trained men performed a squat jump 2 minutes after a control protocol or 2 COHSs at 90% of their 1 repetition maximum (1RM) COHS performed in a ballistic or nonballistic manner. Jump height (JH), peak power (PP), and allometrically scaled peak power (PPa) were compared using three 3 × 2 repeated-measures analyses of variance. Statistically significant condition × time interaction effects existed for JH (p = 0.037), PP (p = 0.041), and PPa (p = 0.031). Post hoc analysis revealed that the ballistic condition produced statistically greater JH (p = 0.017 and p = 0.036), PP (p = 0.031 and p = 0.026), and PPa (p = 0.024 and p = 0.023) than the control and nonballistic conditions, respectively. Small effect sizes for JH, PP, and PPa existed during the ballistic condition (d = 0.28-0.44), whereas trivial effect sizes existed during the control (d = 0.0-0.18) and nonballistic (d = 0.0-0.17) conditions. Large statistically significant relationships existed between the JH potentiation response and the subject's relative back squat 1RM (r = 0.520; p = 0.047) and relative COHS 1RM (r = 0.569; p = 0.027) during the ballistic condition. In addition, large statistically significant relationship existed between JH potentiation response and the subject's relative back squat strength (r = 0.633; p = 0.011), whereas the moderate relationship with the subject's relative COHS strength trended toward significance (r = 0.483; p = 0.068). Ballistic COHS produced superior potentiation effects compared with COHS performed in a nonballistic manner. Relative strength may contribute to the elicited potentiation response after ballistic and nonballistic COHS.

Micrometeoroid and Orbital Debris Threat Assessment: Mars Sample Return Earth Entry Vehicle

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Hyde, James L.; Bjorkman, Michael D.; Hoffman, Kevin D.; Lear, Dana M.; Prior, Thomas G.

2011-01-01

This report provides results of a Micrometeoroid and Orbital Debris (MMOD) risk assessment of the Mars Sample Return Earth Entry Vehicle (MSR EEV). The assessment was performed using standard risk assessment methodology illustrated in Figure 1-1. Central to the process is the Bumper risk assessment code (Figure 1-2), which calculates the critical penetration risk based on geometry, shielding configurations and flight parameters. The assessment process begins by building a finite element model (FEM) of the spacecraft, which defines the size and shape of the spacecraft as well as the locations of the various shielding configurations. This model is built using the NX I-deas software package from Siemens PLM Software. The FEM is constructed using triangular and quadrilateral elements that define the outer shell of the spacecraft. Bumper-II uses the model file to determine the geometry of the spacecraft for the analysis. The next step of the process is to identify the ballistic limit characteristics for the various shield types. These ballistic limits define the critical size particle that will penetrate a shield at a given impact angle and impact velocity. When the finite element model is built, each individual element is assigned a property identifier (PID) to act as an index for its shielding properties. Using the ballistic limit equations (BLEs) built into the Bumper-II code, the shield characteristics are defined for each and every PID in the model. The final stage of the analysis is to determine the probability of no penetration (PNP) on the spacecraft. This is done using the micrometeoroid and orbital debris environment definitions that are built into the Bumper-II code. These engineering models take into account orbit inclination, altitude, attitude and analysis date in order to predict an impacting particle flux on the spacecraft. Using the geometry and shielding characteristics previously defined for the spacecraft and combining that information with the environment model calculations, the Bumper-II code calculates a probability of no penetration for the spacecraft.

Swimming of Paramecium in confined channels

NASA Astrophysics Data System (ADS)

Jung, Sunghwan

2012-02-01

Many living organisms in nature have developed a few different swimming modes, presumably derived from hydrodynamic advantage. Paramecium is a ciliated protozoan covered by thousands of cilia with a few nanometers in diameter and tens of micro-meters in length and is able to exhibit both ballistic and meandering motions. First, we characterize ballistic swimming behaviors of ciliated microorganisms in glass capillaries of different diameters and explain the trajectories they trace out. We develop a theoretical model of an undulating sheet with a pressure gradient and discuss how it affects the swimming speed. Secondly, investigation into meandering swimmings within rectangular PDMS channels of dimension smaller than Paramecium length. We find that Paramecium executes a body-bend (an elastic buckling) using the cilia while it meanders. By considering an elastic beam model, we estimate and show the universal profile of forces it exerts on the walls. Finally, we discuss a few other locomotion of Paramecium in other extreme environments like gel.

Heat guiding and focusing using ballistic phonon transport in phononic nanostructures

NASA Astrophysics Data System (ADS)

Anufriev, Roman; Ramiere, Aymeric; Maire, Jeremie; Nomura, Masahiro

2017-05-01

Unlike classical heat diffusion at macroscale, nanoscale heat conduction can occur without energy dissipation because phonons can ballistically travel in straight lines for hundreds of nanometres. Nevertheless, despite recent experimental evidence of such ballistic phonon transport, control over its directionality, and thus its practical use, remains a challenge, as the directions of individual phonons are chaotic. Here, we show a method to control the directionality of ballistic phonon transport using silicon membranes with arrays of holes. First, we demonstrate that the arrays of holes form fluxes of phonons oriented in the same direction. Next, we use these nanostructures as directional sources of ballistic phonons and couple the emitted phonons into nanowires. Finally, we introduce thermal lens nanostructures, in which the emitted phonons converge at the focal point, thus focusing heat into a spot of a few hundred nanometres. These results motivate the concept of ray-like heat manipulations at the nanoscale.

Ballistic Jumping Drops on Superhydrophobic Surfaces via Electrostatic Manipulation.

PubMed

Li, Ning; Wu, Lei; Yu, Cunlong; Dai, Haoyu; Wang, Ting; Dong, Zhichao; Jiang, Lei

2018-02-01

The ballistic ejection of liquid drops by electrostatic manipulating has both fundamental and practical implications, from raindrops in thunderclouds to self-cleaning, anti-icing, condensation, and heat transfer enhancements. In this paper, the ballistic jumping behavior of liquid drops from a superhydrophobic surface is investigated. Powered by the repulsion of the same kind of charges, water drops can jump from the surface. The electrostatic acting time for the jumping of a microliter supercooled drop only takes several milliseconds, even shorter than the time for icing. In addition, one can control the ballistic jumping direction precisely by the relative position above the electrostatic field. The approach offers a facile method that can be used to manipulate the ballistic drop jumping via an electrostatic field, opening the possibility of energy efficient drop detaching techniques in various applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Heat guiding and focusing using ballistic phonon transport in phononic nanostructures.

PubMed

Anufriev, Roman; Ramiere, Aymeric; Maire, Jeremie; Nomura, Masahiro

2017-05-18

Unlike classical heat diffusion at macroscale, nanoscale heat conduction can occur without energy dissipation because phonons can ballistically travel in straight lines for hundreds of nanometres. Nevertheless, despite recent experimental evidence of such ballistic phonon transport, control over its directionality, and thus its practical use, remains a challenge, as the directions of individual phonons are chaotic. Here, we show a method to control the directionality of ballistic phonon transport using silicon membranes with arrays of holes. First, we demonstrate that the arrays of holes form fluxes of phonons oriented in the same direction. Next, we use these nanostructures as directional sources of ballistic phonons and couple the emitted phonons into nanowires. Finally, we introduce thermal lens nanostructures, in which the emitted phonons converge at the focal point, thus focusing heat into a spot of a few hundred nanometres. These results motivate the concept of ray-like heat manipulations at the nanoscale.

Heat guiding and focusing using ballistic phonon transport in phononic nanostructures

PubMed Central

Anufriev, Roman; Ramiere, Aymeric; Maire, Jeremie; Nomura, Masahiro

2017-01-01

Unlike classical heat diffusion at macroscale, nanoscale heat conduction can occur without energy dissipation because phonons can ballistically travel in straight lines for hundreds of nanometres. Nevertheless, despite recent experimental evidence of such ballistic phonon transport, control over its directionality, and thus its practical use, remains a challenge, as the directions of individual phonons are chaotic. Here, we show a method to control the directionality of ballistic phonon transport using silicon membranes with arrays of holes. First, we demonstrate that the arrays of holes form fluxes of phonons oriented in the same direction. Next, we use these nanostructures as directional sources of ballistic phonons and couple the emitted phonons into nanowires. Finally, we introduce thermal lens nanostructures, in which the emitted phonons converge at the focal point, thus focusing heat into a spot of a few hundred nanometres. These results motivate the concept of ray-like heat manipulations at the nanoscale. PMID:28516909

Ballistic Analysis of New Military Grade Magnesium Alloys for Armor Applications

NASA Astrophysics Data System (ADS)

Jones, Tyrone L.; Kondoh, Katsuyoshi

Since 2006, the U.S. Army has been evaluating magnesium (Mg) alloys for ballistic structural applications. While Mg-alloys have been used in military structural applications since WWII, very little research has been done to improve its mediocre ballistic performance. The Army's need for ultra-lightweight armor systems has led to research and development of high strength, high ductility Mg-alloys. The U.S. Army Research Laboratory contracted through International Technology Center-Pacific Contract Number FA-5209-09-P-0158 with the Joining and Welding Research Instituteof Osaka University to develop the next generation of high strength, high ductility Mg-alloys using a novel Spinning Water Atomization Process for rapid solidification. New alloys AMX602 and ZAXE1711 in extruded bar form were characterized for microstructure, mechanical, and ballistic response. Significant increases in ballistic performance were evident when compared to the baseline alloy AZ31B.

Modeling the near-Earth interaction between ring current ions and exospheric neutrals: escape through energetic neutral atoms (ENAs)

NASA Astrophysics Data System (ADS)

LLera, K.; Goldstein, J.; McComas, D. J.; Valek, P. W.

2016-12-01

The two major loss processes for ring current decay are precipitation and energetic neutral atoms (ENAs). Since the exospheric neutral density increases with decreasing altitudes, precipitating ring current ions (reaching down to 200 - 800 km in altitude) also produce low-altitude ENA signatures that can be stronger than the ring current emission at equatorial distances ( 2 - 9 Re). The higher density results in multiple collisions between the ring current ions and exospheric oxygen. The affect on hydrogen ions is the focus of this study. Since the H particle sustains energy loss ( 36 eV) at each neutralizing or re-ionizing interaction, the escaped ENAs do not directly reflect the ring current properties. We model the energy loss due to multiple charge exchange and electron stripping interactions of 1 - 100 keV precipitating ring current ions undergo before emerging as low-altitude ENAs. The H particle is either an ion or an ENA throughout the simulation. Their lifetime is analytically determined by the length of one mean free path. We track the ion state with Lorentz motion while the ENA travels ballistically across the geomagnetic field. Our simulations show the energy loss is greater than 20% for hydrogen ring current ions below 30 keV (60 keV for the simulations that wander equatorward). This is the first quantification of the energy loss associated with the creation of low-altitude ENAs. Our model (currently constrained in the meridional plane) has revealed characteristics on how precipitation is affected by the near-Earth neutral exosphere. This ion-neutral interaction removes particles from the loss cone but promotes loss through ENA generation. These findings should be implemented in models predicting the ring current decay and used as an analysis tool to reconstruct the ring current population from observed low-altitude ENAs.

2014 Mount Ontake eruption: characteristics of the phreatic eruption as inferred from aerial observations

NASA Astrophysics Data System (ADS)

Kaneko, Takayuki; Maeno, Fukashi; Nakada, Setsuya

2016-05-01

The sudden eruption of Mount Ontake on September 27, 2014, led to a tragedy that caused more than 60 fatalities including missing persons. In order to mitigate the potential risks posed by similar volcano-related disasters, it is vital to have a clear understanding of the activity status and progression of eruptions. Because the erupted material was largely disturbed while access was strictly prohibited for a month, we analyzed the aerial photographs taken on September 28. The results showed that there were three large vents in the bottom of the Jigokudani valley on September 28. The vent in the center was considered to have been the main vent involved in the eruption, and the vents on either side were considered to have been formed by non-explosive processes. The pyroclastic flows extended approximately 2.5 km along the valley at an average speed of 32 km/h. The absence of burned or fallen trees in this area indicated that the temperatures and destructive forces associated with the pyroclastic flow were both low. The distribution of ballistics was categorized into four zones based on the number of impact craters per unit area, and the furthest impact crater was located 950 m from the vents. Based on ballistic models, the maximum initial velocity of the ejecta was estimated to be 111 m/s. Just after the beginning of the eruption, very few ballistic ejecta had arrived at the summit, even though the eruption plume had risen above the summit, which suggested that a large amount of ballistic ejecta was expelled from the volcano several tens-of-seconds after the beginning of the eruption. This initial period was characterized by the escape of a vapor phase from the vents, which then caused the explosive eruption phase that generated large amounts of ballistic ejecta via sudden decompression of a hydrothermal reservoir.

Computational model for simulation small testing launcher, technical solution

NASA Astrophysics Data System (ADS)

Chelaru, Teodor-Viorel; Cristian, Barbu; Chelaru, Adrian

2014-12-01

The purpose of this paper is to present some aspects regarding the computational model and technical solutions for multistage suborbital launcher for testing (SLT) used to test spatial equipment and scientific measurements. The computational model consists in numerical simulation of SLT evolution for different start conditions. The launcher model presented will be with six degrees of freedom (6DOF) and variable mass. The results analysed will be the flight parameters and ballistic performances. The discussions area will focus around the technical possibility to realize a small multi-stage launcher, by recycling military rocket motors. From technical point of view, the paper is focused on national project "Suborbital Launcher for Testing" (SLT), which is based on hybrid propulsion and control systems, obtained through an original design. Therefore, while classical suborbital sounding rockets are unguided and they use as propulsion solid fuel motor having an uncontrolled ballistic flight, SLT project is introducing a different approach, by proposing the creation of a guided suborbital launcher, which is basically a satellite launcher at a smaller scale, containing its main subsystems. This is why the project itself can be considered an intermediary step in the development of a wider range of launching systems based on hybrid propulsion technology, which may have a major impact in the future European launchers programs. SLT project, as it is shown in the title, has two major objectives: first, a short term objective, which consists in obtaining a suborbital launching system which will be able to go into service in a predictable period of time, and a long term objective that consists in the development and testing of some unconventional sub-systems which will be integrated later in the satellite launcher as a part of the European space program. This is why the technical content of the project must be carried out beyond the range of the existing suborbital vehicle programs towards the current technological necessities in the space field, especially the European one.

Computational model for simulation small testing launcher, technical solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chelaru, Teodor-Viorel, E-mail: teodor.chelaru@upb.ro; Cristian, Barbu, E-mail: barbucr@mta.ro; Chelaru, Adrian, E-mail: achelaru@incas.ro

The purpose of this paper is to present some aspects regarding the computational model and technical solutions for multistage suborbital launcher for testing (SLT) used to test spatial equipment and scientific measurements. The computational model consists in numerical simulation of SLT evolution for different start conditions. The launcher model presented will be with six degrees of freedom (6DOF) and variable mass. The results analysed will be the flight parameters and ballistic performances. The discussions area will focus around the technical possibility to realize a small multi-stage launcher, by recycling military rocket motors. From technical point of view, the paper ismore » focused on national project 'Suborbital Launcher for Testing' (SLT), which is based on hybrid propulsion and control systems, obtained through an original design. Therefore, while classical suborbital sounding rockets are unguided and they use as propulsion solid fuel motor having an uncontrolled ballistic flight, SLT project is introducing a different approach, by proposing the creation of a guided suborbital launcher, which is basically a satellite launcher at a smaller scale, containing its main subsystems. This is why the project itself can be considered an intermediary step in the development of a wider range of launching systems based on hybrid propulsion technology, which may have a major impact in the future European launchers programs. SLT project, as it is shown in the title, has two major objectives: first, a short term objective, which consists in obtaining a suborbital launching system which will be able to go into service in a predictable period of time, and a long term objective that consists in the development and testing of some unconventional sub-systems which will be integrated later in the satellite launcher as a part of the European space program. This is why the technical content of the project must be carried out beyond the range of the existing suborbital vehicle programs towards the current technological necessities in the space field, especially the European one.« less

MAGNESIUM ALLOYS IN US MILITARY APPLICATIONS: PAST, CURRENT AND FUTURE SOLUTIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mathaudhu, Suveen N.; Nyberg, Eric A.

2010-02-26

Since the 1940’s Mg-alloys have been used for military applications, from aircraft components to ground vehicles. The drive for usage was primarily availability and lightweighting of military systems. But the promise of widespread military usage was not met largely based on corrosion and flammability concerns, poor mechanical behavior and inferior ballistic response. This review paper will cover historical, current and potential future applications with a focus on scientific, engineering and social barriers relevant to integration of Mg-alloy. It will also present mechanical and physical property improvements solutions which are currently being developed to address these issues.

Initial Validation of Ballistic Shock Transducers

DTIC Science & Technology

2017-06-05

objective of this TOP is to describe various methods and instrumentation used in the initial validation of accelerometers to be used in both Ballistic...MILITARY STANDARD 810G CHANGE NOTICE 1, METHOD 522.2, SECTION 4.4.2 ....................................... A-1 B. GLOSSARY...Procedure (TOP) is to describe various methods and instrumentation used in the initial validation of accelerometers to be used in both Ballistic

Airborne ballistic camera tracking systems

NASA Technical Reports Server (NTRS)

Redish, W. L.

1976-01-01

An operational airborne ballistic camera tracking system was tested for operational and data reduction feasibility. The acquisition and data processing requirements of the system are discussed. Suggestions for future improvements are also noted. A description of the data reduction mathematics is outlined. Results from a successful reentry test mission are tabulated. The test mission indicated that airborne ballistic camera tracking systems are feasible.

Ballistic trauma: lessons learned from iraq and afghanistan.

PubMed

Shin, Emily H; Sabino, Jennifer M; Nanos, George P; Valerio, Ian L

2015-02-01

Management of upper extremity injuries secondary to ballistic and blast trauma can lead to challenging problems for the reconstructive surgeon. Given the recent conflicts in Iraq and Afghanistan, advancements in combat-casualty care, combined with a high-volume experience in the treatment of ballistic injuries, has led to continued advancements in the treatment of the severely injured upper extremity. There are several lessons learned that are translatable to civilian trauma centers and future conflicts. In this article, the authors provide an overview of the physics of ballistic injuries and principles in the management of such injuries through experience gained from military involvement in Iraq and Afghanistan.

Ballistic anisotropic magnetoresistance in core-shell nanowires and rolled-up nanotubes

NASA Astrophysics Data System (ADS)

Chang, Ching-Hao; Ortix, Carmine

2017-01-01

In ferromagnetic nanostructures, the ballistic anisotropic magnetoresistance (BAMR) is a change in the ballistic conductance with the direction of magnetization due to spin-orbit interaction. Very recently, a directional dependent ballistic conductance has been predicted to occur in a number of newly synthesized nonmagnetic semiconducting nanostructures subject to externally applied magnetic fields, without necessitating spin-orbit coupling. In this paper, we review past works on the prediction of this BAMR effect in core-shell nanowires (CSN) and rolled-up nanotubes (RUNTs). This is complemented by new results, we establish for the transport properties of tubular nanosystems subject to external magnetic fields.

Ballistic Trauma: Lessons Learned from Iraq and Afghanistan

PubMed Central

Shin, Emily H.; Sabino, Jennifer M.; Nanos, George P.; Valerio, Ian L.

2015-01-01

Management of upper extremity injuries secondary to ballistic and blast trauma can lead to challenging problems for the reconstructive surgeon. Given the recent conflicts in Iraq and Afghanistan, advancements in combat-casualty care, combined with a high-volume experience in the treatment of ballistic injuries, has led to continued advancements in the treatment of the severely injured upper extremity. There are several lessons learned that are translatable to civilian trauma centers and future conflicts. In this article, the authors provide an overview of the physics of ballistic injuries and principles in the management of such injuries through experience gained from military involvement in Iraq and Afghanistan. PMID:25685099

Comparative Ballistic Performance of 20mm AP M95 and 20mm AP M75 Projectiles against Rolled Homogeneous Steel Armor

DTIC Science & Technology

1960-05-01

Dominic A. Piccione, " Comparative Ballistic Performanceof 20mm AP M95 and 20mm AP M75 Projectiles againstRolled Homogeneous Steel Armor (U)’\\ WAL-TR-160.1/1... COMPARATIVE BALLISTIC PERFORMANCE OF 20MM AP M95 AND 20MM AP M75 PROJECTILES AGAINST ROLLED HOMOGENEOUS STEEL ARMOR (U) TECHNICAL REPORT NO. WAL TR I60.l/I(c...o > -< Abt9sortf bl O *_, o o -o WATERTOWN ARSENAL LABORATORIES co COMPARATIVE BALLISTIC PERFORMANCE OF 20MM AP M95 AND 20MM AP M75

Ballistic Resistance of Honeycomb Sandwich Panels under In-Plane High-Velocity Impact

PubMed Central

Yang, Shu; Wang, Dong; Yang, Li-Jun

2013-01-01

The dynamic responses of honeycomb sandwich panels (HSPs) subjected to in-plane projectile impact were studied by means of explicit nonlinear finite element simulations using LS-DYNA. The HSPs consisted of two identical aluminum alloy face-sheets and an aluminum honeycomb core featuring three types of unit cell configurations (regular, rectangular-shaped, and reentrant hexagons). The ballistic resistances of HSPs with the three core configurations were first analyzed. It was found that the HSP with the reentrant auxetic honeycomb core has the best ballistic resistance, due to the negative Poisson's ratio effect of the core. Parametric studies were then carried out to clarify the influences of both macroscopic (face-sheet and core thicknesses, core relative density) and mesoscopic (unit cell angle and size) parameters on the ballistic responses of the auxetic HSPs. Numerical results show that the perforation resistant capabilities of the auxetic HSPs increase as the values of the macroscopic parameters increase. However, the mesoscopic parameters show nonmonotonic effects on the panels' ballistic capacities. The empirical equations for projectile residual velocities were formulated in terms of impact velocity and the structural parameters. It was also found that the blunter projectiles result in higher ballistic limits of the auxetic HSPs. PMID:24187526

Nonlinear Ballistic Transport in an Atomically Thin Material.

PubMed

Boland, Mathias J; Sundararajan, Abhishek; Farrokhi, M Javad; Strachan, Douglas R

2016-01-26

Ultrashort devices that incorporate atomically thin components have the potential to be the smallest electronics. Such extremely scaled atomically thin devices are expected to show ballistic nonlinear behavior that could make them tremendously useful for ultrafast applications. While nonlinear diffusive electron transport has been widely reported, clear evidence for intrinsic nonlinear ballistic transport in the growing array of atomically thin conductors has so far been elusive. Here we report nonlinear electron transport of an ultrashort single-layer graphene channel that shows quantitative agreement with intrinsic ballistic transport. This behavior is shown to be distinctly different than that observed in similarly prepared ultrashort devices consisting, instead, of bilayer graphene channels. These results suggest that the addition of only one extra layer of an atomically thin material can make a significant impact on the nonlinear ballistic behavior of ultrashort devices, which is possibly due to the very different chiral tunneling of their charge carriers. The fact that we observe the nonlinear ballistic response at room temperature, with zero applied magnetic field, in non-ultrahigh vacuum conditions and directly on a readily accessible oxide substrate makes the nanogap technology we utilize of great potential for achieving extremely scaled high-speed atomically thin devices.

Time-gated ballistic imaging using a large aperture switching beam.

PubMed

Mathieu, Florian; Reddemann, Manuel A; Palmer, Johannes; Kneer, Reinhold

2014-03-24

Ballistic imaging commonly denotes the formation of line-of-sight shadowgraphs through turbid media by suppression of multiply scattered photons. The technique relies on a femtosecond laser acting as light source for the images and as switch for an optical Kerr gate that separates ballistic photons from multiply scattered ones. The achievable image resolution is one major limitation for the investigation of small objects. In this study, practical influences on the optical Kerr gate and image quality are discussed theoretically and experimentally applying a switching beam with large aperture (D = 19 mm). It is shown how switching pulse energy and synchronization of switching and imaging pulse in the Kerr cell influence the gate's transmission. Image quality of ballistic imaging and standard shadowgraphy is evaluated and compared, showing that the present ballistic imaging setup is advantageous for optical densities in the range of 8 < OD < 13. Owing to the spatial transmission characteristics of the optical Kerr gate, a rectangular aperture stop is formed, which leads to different resolution limits for vertical and horizontal structures in the object. Furthermore, it is reported how to convert the ballistic imaging setup into a schlieren-type system with an optical schlieren edge.

Ballistic resistance of honeycomb sandwich panels under in-plane high-velocity impact.

PubMed

Qi, Chang; Yang, Shu; Wang, Dong; Yang, Li-Jun

2013-01-01

The dynamic responses of honeycomb sandwich panels (HSPs) subjected to in-plane projectile impact were studied by means of explicit nonlinear finite element simulations using LS-DYNA. The HSPs consisted of two identical aluminum alloy face-sheets and an aluminum honeycomb core featuring three types of unit cell configurations (regular, rectangular-shaped, and reentrant hexagons). The ballistic resistances of HSPs with the three core configurations were first analyzed. It was found that the HSP with the reentrant auxetic honeycomb core has the best ballistic resistance, due to the negative Poisson's ratio effect of the core. Parametric studies were then carried out to clarify the influences of both macroscopic (face-sheet and core thicknesses, core relative density) and mesoscopic (unit cell angle and size) parameters on the ballistic responses of the auxetic HSPs. Numerical results show that the perforation resistant capabilities of the auxetic HSPs increase as the values of the macroscopic parameters increase. However, the mesoscopic parameters show nonmonotonic effects on the panels' ballistic capacities. The empirical equations for projectile residual velocities were formulated in terms of impact velocity and the structural parameters. It was also found that the blunter projectiles result in higher ballistic limits of the auxetic HSPs.

The Effect of Temperature and Nanoclay on the Low Velocity and Ballistic Behavior of Woven Glass-Fiber Reinforced Composites

NASA Astrophysics Data System (ADS)

Patrin, Lauren

The objective of this research was to study the effect of nanoclay and temperature on the behavior of woven glass-fabric reinforced epoxy composite under low velocity and ballistic impacts. The materials used in manufacturing the composite were S2 (6181) glass-fibers, epoxy resin (EPON 828), hardener (Epikure 3230), nanoclay and Heloxy 61 modifier. The nanoclay addition was 0%, 1%, 3% and 5% by weight, with respect to the resin. All specimens were manufactured at the City College facilities using vacuum infusion. Tensile tests were conducted to characterize the material and obtain the Young's modulus, ultimate stress, failure strain, Poisson's ratio, shear modulus and shear strength and their variation with nanoclay percentage and temperature. The tests were conducted at room temperature (21°C/70°F), -54°C (-65°F), -20°C (-4°F), 49°C (120°F) and 71°C (160°F). Next composite specimens with 0%, 1%, 3% and 5% nanoclay by weight, with respect to the resin, were subjected to low velocity impact at the previously specified temperatures to determine dynamic force, displacement and energy correlations. The extent of damage was studied using the ultrasound technique. Then ballistic tests were conducted on the nanoclay infused specimens at room temperature to obtain the ballistic limit (V50) and the damage behavior of the composite. The dynamic finite element analysis (FEA) software LS-DYNA was used to model and simulate the results of low velocity impact tests. Good agreement was obtained between experimental and numerical (FEA) results. Analytical analyses were undertaken to compare the results from the tensile experiments. The finite element analysis (FEA) allowed for further analytical comparison of the results. The FEA platform used was LS-DYNA due to its proficient dynamic and damage capabilities in composite materials. The FEA was used to model and simulate the low velocity impacts and compare the results to experiments.

Bumper 3 Update for IADC Protection Manual

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Nagy, Kornel; Hyde, Jim

2016-01-01

The Bumper code has been the standard in use by NASA and contractors to perform meteoroid/debris risk assessments since 1990. It has undergone extensive revisions and updates [NASA JSC HITF website; Christiansen et al., 1992, 1997]. NASA Johnson Space Center (JSC) has applied BUMPER to risk assessments for Space Station, Shuttle, Mir, Extravehicular Mobility Units (EMU) space suits, and other spacecraft (e.g., LDEF, Iridium, TDRS, and Hubble Space Telescope). Bumper continues to be updated with changes in the ballistic limit equations describing failure threshold of various spacecraft components, as well as changes in the meteoroid and debris environment models. Significant efforts are expended to validate Bumper and benchmark it to other meteoroid/debris risk assessment codes. Bumper 3 is a refactored version of Bumper II. The structure of the code was extensively modified to improve maintenance, performance and flexibility. The architecture was changed to separate the frequently updated ballistic limit equations from the relatively stable common core functions of the program. These updates allow NASA to produce specific editions of the Bumper 3 that are tailored for specific customer requirements. The core consists of common code necessary to process the Micrometeoroid and Orbital Debris (MMOD) environment models, assess shadowing and calculate MMOD risk. The library of target response subroutines includes a board range of different types of MMOD shield ballistic limit equations as well as equations describing damage to various spacecraft subsystems or hardware (thermal protection materials, windows, radiators, solar arrays, cables, etc.). The core and library of ballistic response subroutines are maintained under configuration control. A change in the core will affect all editions of the code, whereas a change in one or more of the response subroutines will affect all editions of the code that contain the particular response subroutines which are modified. Note that the Bumper II program is no longer maintained or distributed by NASA.

Transverse thermal conductivity of porous materials made from aligned nano- and microcylindrical pores

NASA Astrophysics Data System (ADS)

Prasher, Ravi

2006-09-01

Nanoporous and microporous materials made from aligned cylindrical pores play important roles in present technologies and will play even bigger roles in future technologies. The insight into the phonon thermal conductivity of these materials is important and relevant in many technologies and applications. Since the mean free path of phonons can be comparable to the pore size and interpore distance, diffusion-approximation based effective medium models cannot be used to predict the thermal conductivity of these materials. Strictly speaking, the Boltzmann transport equation (BTE) must be solved to capture the ballistic nature of thermal transport; however, solving BTE in such a complex network of pores is impractical. As an alternative, we propose an approximate ballistic-diffusive microscopic effective medium model for predicting the thermal conductivity of phonons in two-dimensional nanoporous and microporous materials made from aligned cylindrical pores. The model captures the size effects due to the pore diameter and the interpore distance and reduces to diffusion-approximation based models for macroporous materials. The results are in good agreement with experimental data.

MODELING POROUS DUST GRAINS WITH BALLISTIC AGGREGATES. II. LIGHT SCATTERING PROPERTIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen Yue; Draine, B. T.; Johnson, Eric T.

2009-05-10

We study the light scattering properties of random ballistic aggregates constructed in Shen et al. Using the discrete-dipole approximation, we compute the scattering phase function and linear polarization for random aggregates with various sizes and porosities, and with two different compositions: 100% silicate and 50% silicate +50% graphite. We investigate the dependence of light scattering properties on wavelength, cluster size, and porosity using these aggregate models. We find that while the shape of the phase function depends mainly on the size parameter of the aggregates, the linear polarization depends on both the size parameter and the porosity of the aggregates,more » with increasing degree of polarization as the porosity increases. Contrary to previous studies, we argue that the monomer size has negligible effects on the light scattering properties of ballistic aggregates, as long as the constituent monomer is smaller than the incident wavelength up to 2{pi}a {sub 0}/{lambda} {approx} 1.6 where a {sub 0} is the monomer radius. Previous claims for such monomer size effects are in fact the combined effects of size parameter and porosity. Finally, we present aggregate models that can reproduce the phase function and polarization of scattered light from the AU Mic debris disk and from cometary dust, including the negative polarization observed for comets at scattering angles 160 deg. {approx}< {theta} < 180 deg. These aggregates have moderate porosities, P{approx}0.6, and are of sub-{mu}m size for the debris disk case, or {mu}m size for the comet case.« less

Great Balls of Fire: A probabilistic approach to quantify the hazard related to ballistics - A case study at La Fossa volcano, Vulcano Island, Italy

NASA Astrophysics Data System (ADS)

Biass, Sébastien; Falcone, Jean-Luc; Bonadonna, Costanza; Di Traglia, Federico; Pistolesi, Marco; Rosi, Mauro; Lestuzzi, Pierino

2016-10-01

We present a probabilistic approach to quantify the hazard posed by volcanic ballistic projectiles (VBP) and their potential impact on the built environment. A model named Great Balls of Fire (GBF) is introduced to describe ballistic trajectories of VBPs accounting for a variable drag coefficient and topography. It relies on input parameters easily identifiable in the field and is designed to model large numbers of VBPs stochastically. Associated functions come with the GBF code to post-process model outputs into a comprehensive probabilistic hazard assessment for VBP impacts. Outcomes include probability maps to exceed given thresholds of kinetic energies at impact, hazard curves and probabilistic isoenergy maps. Probabilities are calculated either on equally-sized pixels or zones of interest. The approach is calibrated, validated and applied to La Fossa volcano, Vulcano Island (Italy). We constructed a generic eruption scenario based on stratigraphic studies and numerical inversions of the 1888-1890 long-lasting Vulcanian cycle of La Fossa. Results suggest a ~ 10- 2% probability of occurrence of VBP impacts with kinetic energies ≤ 104 J at the touristic locality of Porto. In parallel, the vulnerability to roof perforation was estimated by combining field observations and published literature, allowing for a first estimate of the potential impact of VBPs during future Vulcanian eruptions. Results indicate a high physical vulnerability to the VBP hazard, and, consequently, half of the building stock having a ≥ 2.5 × 10- 3% probability of roof perforation.

Gunshot injuries.

PubMed

Hinkle, J; Betz, S

1995-05-01

If current trends for this nation continue, by the year 2003 the number of people killed by firearms will exceed the number of people killed in motor vehicle accidents. Critical care practitioners must understand the mechanism of injury associated with firearm injuries to provide optimal care. This article reviews internal, exterior, and terminal ballistics, bullet design, wound classification, and initial assessment and treatment of firearm injuries.

Analysis of nonlocal phonon thermal conductivity simulations showing the ballistic to diffusive crossover

NASA Astrophysics Data System (ADS)

Allen, Philip B.

2018-04-01

Simulations [e.g., X. W. Zhou et al., Phys. Rev. B 79, 115201 (2009), 10.1103/PhysRevB.79.115201] show nonlocal effects of the ballistic/diffusive crossover. The local temperature has nonlinear spatial variation not contained in the local Fourier law j ⃗(r ⃗) =-κ ∇ ⃗T (r ⃗) . The heat current j ⃗(r ⃗) depends not just on the local temperature gradient ∇ ⃗T (r ⃗) but also on temperatures at points r⃗' within phonon mean free paths, which can be micrometers long. This paper uses the Peierls-Boltzmann transport theory in nonlocal form to analyze the spatial variation Δ T (r ⃗) . The relaxation-time approximation (RTA) is used because the full solution is very challenging. Improved methods of extrapolation to obtain the bulk thermal conductivity κ are proposed. Callaway invented an approximate method of correcting RTA for the q ⃗ (phonon wave vector or crystal momentum) conservation of N (Normal as opposed to Umklapp) anharmonic collisions. This method is generalized to the nonlocal case where κ (k ⃗) depends on the wave vector of the current j ⃗(k ⃗) and temperature gradient i k ⃗Δ T (k ⃗) .

Ballistic induced pumping of hypersonic heat current in DNA nano wire

NASA Astrophysics Data System (ADS)

Behnia, Sohrab; Panahinia, Robabe

2016-12-01

Heat shuttling properties of DNA nano-wire driven by an external force against the spontaneous heat current direction in non-zero temperature bias (non averaged) have been studied. We examined the valid region of driving amplitude and frequency to have pumping state in terms of temperature bias and the system size. It was shown that DNA could act as a high efficiency thermal pump in the hypersonic region. Amplitude-dependent resonance frequencies of DNA indicating intrinsic base pair internal vibrations have been detected. Nonlinearity implies that by increasing the driven amplitude new vibration modes are detected. To verify the results, an analytical parallel investigation based on multifractal concept has been done. By using the geometric properties of the strange attractor of the system, the threshold value to transition to the pumping state for given external amplitude has been identified. It was shown that the system undergoes a phase transition in sliding point to the pumping state. Fractal dimension demonstrates that the ballistic transport is responsible for energy pumping in the system. In the forbidden band gap, DNA could transmit the energy by exceeding the threshold amplitude. Despite of success in energy pumping, in this framework, DNA could not act as a real cooler.

Performance analysis of boron nitride embedded armchair graphene nanoribbon metal-oxide-semiconductor field effect transistor with Stone Wales defects

NASA Astrophysics Data System (ADS)

Chanana, Anuja; Sengupta, Amretashis; Mahapatra, Santanu

2014-01-01

We study the performance of a hybrid Graphene-Boron Nitride armchair nanoribbon (a-GNR-BN) n-MOSFET at its ballistic transport limit. We consider three geometric configurations 3p, 3p + 1, and 3p + 2 of a-GNR-BN with BN atoms embedded on either side (2, 4, and 6 BN) on the GNR. Material properties like band gap, effective mass, and density of states of these H-passivated structures are evaluated using the Density Functional Theory. Using these material parameters, self-consistent Poisson-Schrodinger simulations are carried out under the Non Equilibrium Green's Function formalism to calculate the ballistic n-MOSFET device characteristics. For a hybrid nanoribbon of width ˜5 nm, the simulated ON current is found to be in the range of 265 μA-280 μA with an ON/OFF ratio 7.1 × 106-7.4 × 106 for a VDD = 0.68 V corresponding to 10 nm technology node. We further study the impact of randomly distributed Stone Wales (SW) defects in these hybrid structures and only 2.5% degradation of ON current is observed for SW defect density of 3.18%.

Evaluating Training.

ERIC Educational Resources Information Center

Brethower, Karen S.; Rummler, Geary A.

1979-01-01

Presents general systems models (ballistic system, guided system, and adaptive system) and an evaluation matrix to help in examining training evaluation alternatives and in deciding what evaluation is appropriate. Includes some guidelines for conducting evaluation studies using four designs (control group, reversal, multiple baseline, and…

2005 22nd International Symposium on Ballistics. Volume 3 Thursday - Friday

DTIC Science & Technology

2005-11-18

QinetiQ; Vladimir Titarev, Eleuterio Toro , Umeritek Limited The Mechanism Analysis of Interior Ballistics of Serial Chamber Gun, Dr. Sanjiu Ying, Charge...Elements and Meshless Particles, Gordon R. Johnson and Robert A. Stryk, Network Computing Services, Inc. Experimental and Numerical Study of the...Internal Ballistics Clive R. Woodley, David Finbow, QinetiQ; Vladimir Titarev, Eleuterio Toro , Numeritek Limited 22nd International Symposium on

Conventional Prompt Global Strike and Long Range Ballistic Missiles: Background and Issues

DTIC Science & Technology

2017-02-03

Conventional Prompt Global Strike and Long-Range Ballistic Missiles: Background and Issues Amy F. Woolf Specialist in Nuclear Weapons Policy...February 3, 2017 Congressional Research Service 7-5700 www.crs.gov R41464 Conventional Prompt Global Strike and Long-Range Ballistic Missiles...Congressional Research Service Summary Conventional prompt global strike (CPGS) weapons would allow the United States to strike targets anywhere

Ballistic Characterization of the Scalability of Magnesium Alloy AMX602

DTIC Science & Technology

2015-07-01

Powder Metallurgy 4 5. Fabrication Procedure 4 6. Mechanical Property Analysis 5 7. Ballistic Experimental Procedures 6 8. Ballistic Experimental...compositions of noncombustive Mg alloy powders 4. Powder Metallurgy The powder was consolidated at room temperature using a 2,000-kN hydraulic press...evaluation of advanced powder metallurgy magnesium alloys for dynamic applications. Aberdeen Proving Ground (MD): Army Research Laboratory (US); 2009 May

Sabots, Obturator and Gas-In-Launch Tube Techniques for Heat Flux Models in Ballistic Ranges

NASA Technical Reports Server (NTRS)

Bogdanoff, David W.; Wilder, Michael C.

2013-01-01

For thermal protection system (heat shield) design for space vehicle entry into earth and other planetary atmospheres, it is essential to know the augmentation of the heat flux due to vehicle surface roughness. At the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (HFFAF) ballistic range, a campaign of heat flux studies on rough models, using infrared camera techniques, has been initiated. Several phenomena can interfere with obtaining good heat flux data when using this measuring technique. These include leakage of the hot drive gas in the gun barrel through joints in the sabot (model carrier) to create spurious thermal imprints on the model forebody, deposition of sabot material on the model forebody, thereby changing the thermal properties of the model surface and unknown in-barrel heating of the model. This report presents developments in launch techniques to greatly reduce or eliminate these problems. The techniques include the use of obturator cups behind the launch package, enclosed versus open front sabot designs and the use of hydrogen gas in the launch tube. Attention also had to be paid to the problem of the obturator drafting behind the model and impacting the model. Of the techniques presented, the obturator cups and hydrogen in the launch tube were successful when properly implemented

From military to civil loadings: Preliminary numerical-based thorax injury criteria investigations.

PubMed

Goumtcha, Aristide Awoukeng; Bodo, Michèle; Taddei, Lorenzo; Roth, Sébastien

2016-03-01

Effects of the impact of a mechanical structure on the human body are of great interest in the understanding of body trauma. Experimental tests have led to first conclusions about the dangerousness of an impact observing impact forces or displacement time history with PMHS (Post Mortem human Subjects). They have allowed providing interesting data for the development and the validation of numerical biomechanical models. These models, widely used in the framework of automotive crashworthiness, have led to the development of numerical-based injury criteria and tolerance thresholds. The aim of this process is to improve the safety of mechanical structures in interaction with the body. In a military context, investigations both at experimental and numerical level are less successfully completed. For both military and civil frameworks, the literature list a number of numerical analysis trying to propose injury mechanisms, and tolerance thresholds based on biofidelic Finite Element (FE) models of different part of the human body. However the link between both frameworks is not obvious, since lots of parameters are different: great mass impacts at relatively low velocity for civil impacts (falls, automotive crashworthiness) and low mass at very high velocity for military loadings (ballistic, blast). In this study, different accident cases were investigated, and replicated with a previously developed and validated FE model of the human thorax named Hermaphrodite Universal Biomechanical YX model (HUBYX model). These previous validations included replications of standard experimental tests often used to validate models in the context of automotive industry, experimental ballistic tests in high speed dynamic impact and also numerical replication of blast loading test ensuring its biofidelity. In order to extend the use of this model in other frameworks, some real-world accidents were reconstructed, and consequences of these loadings on the FE model were explored. These various numerical replications of accident coming from different contexts raise the question about the ability of a FE model to correctly predict several kinds of trauma, from blast or ballistic impacts to falls, sports or automotive ones in a context of numerical injury mechanisms and tolerance limits investigations. Copyright © 2015 John Wiley & Sons, Ltd.

Tunable quantum criticality and super-ballistic transport in a "charge" Kondo circuit.

PubMed

Iftikhar, Z; Anthore, A; Mitchell, A K; Parmentier, F D; Gennser, U; Ouerghi, A; Cavanna, A; Mora, C; Simon, P; Pierre, F

2018-05-03

Quantum phase transitions (QPTs) are ubiquitous in strongly-correlated materials. However the microscopic complexity of these systems impedes the quantitative understanding of QPTs. Here, we observe and thoroughly analyze the rich strongly-correlated physics in two profoundly dissimilar regimes of quantum criticality. With a circuit implementing a quantum simulator for the three-channel Kondo model, we reveal the universal scalings toward different low-temperature fixed points and along the multiple crossovers from quantum criticality. Notably, an unanticipated violation of the maximum conductance for ballistic free electrons is uncovered. The present charge pseudospin implementation of a Kondo impurity opens access to a broad variety of strongly-correlated phenomena. Copyright © 2018, American Association for the Advancement of Science.

Wavepacket dynamics in one-dimensional system with long-range correlated disorder

NASA Astrophysics Data System (ADS)

Yamada, Hiroaki S.

2018-03-01

We numerically investigate dynamical property in the one-dimensional tight-binding model with long-range correlated disorder having power spectrum 1 /fα (α: spectrum exponent) generated by Fourier filtering method. For relatively small α <αc (=2) time-dependence of mean square displacement (MSD) of the initially localized wavepacket shows ballistic spread and localizes as time elapses. It is shown that α-dependence of the dynamical localization length determined by the MSD exhibits a simple scaling law in the localization regime for the relatively weak disorder strength W. Furthermore, scaled MSD by the dynamical localization length almost obeys an universal function from the ballistic to the localization regime in the various combinations of the parameters α and W.

Characteristic extraction and matching algorithms of ballistic missile in near-space by hyperspectral image analysis

NASA Astrophysics Data System (ADS)

Lu, Li; Sheng, Wen; Liu, Shihua; Zhang, Xianzhi

2014-10-01

The ballistic missile hyperspectral data of imaging spectrometer from the near-space platform are generated by numerical method. The characteristic of the ballistic missile hyperspectral data is extracted and matched based on two different kinds of algorithms, which called transverse counting and quantization coding, respectively. The simulation results show that two algorithms extract the characteristic of ballistic missile adequately and accurately. The algorithm based on the transverse counting has the low complexity and can be implemented easily compared to the algorithm based on the quantization coding does. The transverse counting algorithm also shows the good immunity to the disturbance signals and speed up the matching and recognition of subsequent targets.

Magneto-chiral anisotropy of the free electron on a helix

NASA Astrophysics Data System (ADS)

Krstić, V.; Rikken, G. L. J. A.

2002-09-01

The free electron on a helix as a simple model of a molecular chiral conductor is considered. In the presence of a static magnetic field parallel to the helix axis, it is found that both ballistic and diffusive electrical transport along the helix show a conductivity that depends linearly on the current and the magnetic field and on the handedness of the helix. These results agree qualitatively with the recently experimentally observed electrical magneto-chiral anisotropy in carbon nanotubes [V. Krstić, S. Roth, M. Burghard, K. Kern, G.L.J.A. Rikken, Max-Planck-Institut für Festkörperforschung, Stuttgart, Germany; Grenoble High Magnetic Field Laboratory, MPI-CNRS, Grenoble, France; Laboratoire National des Champs Magnétiques Pulsés, CNRS/INSA/UPS, UMS 5462, Toulouse, France].

A common control signal and a ballistic stage can explain the control of coordinated eye-hand movements.

PubMed

Gopal, Atul; Murthy, Aditya

2016-06-01

Voluntary control has been extensively studied in the context of eye and hand movements made in isolation, yet little is known about the nature of control during eye-hand coordination. We probed this with a redirect task. Here subjects had to make reaching/pointing movements accompanied by coordinated eye movements but had to change their plans when the target occasionally changed its position during some trials. Using a race model framework, we found that separate effector-specific mechanisms may be recruited to control eye and hand movements when executed in isolation but when the same effectors are coordinated a unitary mechanism to control coordinated eye-hand movements is employed. Specifically, we found that performance curves were distinct for the eye and hand when these movements were executed in isolation but were comparable when they were executed together. Second, the time to switch motor plans, called the target step reaction time, was different in the eye-alone and hand-alone conditions but was similar in the coordinated condition under assumption of a ballistic stage of ∼40 ms, on average. Interestingly, the existence of this ballistic stage could predict the extent of eye-hand dissociations seen in individual subjects. Finally, when subjects were explicitly instructed to control specifically a single effector (eye or hand), redirecting one effector had a strong effect on the performance of the other effector. Taken together, these results suggest that a common control signal and a ballistic stage are recruited when coordinated eye-hand movement plans require alteration. Copyright © 2016 the American Physiological Society.

A common control signal and a ballistic stage can explain the control of coordinated eye-hand movements

PubMed Central

Gopal, Atul

2016-01-01

Voluntary control has been extensively studied in the context of eye and hand movements made in isolation, yet little is known about the nature of control during eye-hand coordination. We probed this with a redirect task. Here subjects had to make reaching/pointing movements accompanied by coordinated eye movements but had to change their plans when the target occasionally changed its position during some trials. Using a race model framework, we found that separate effector-specific mechanisms may be recruited to control eye and hand movements when executed in isolation but when the same effectors are coordinated a unitary mechanism to control coordinated eye-hand movements is employed. Specifically, we found that performance curves were distinct for the eye and hand when these movements were executed in isolation but were comparable when they were executed together. Second, the time to switch motor plans, called the target step reaction time, was different in the eye-alone and hand-alone conditions but was similar in the coordinated condition under assumption of a ballistic stage of ∼40 ms, on average. Interestingly, the existence of this ballistic stage could predict the extent of eye-hand dissociations seen in individual subjects. Finally, when subjects were explicitly instructed to control specifically a single effector (eye or hand), redirecting one effector had a strong effect on the performance of the other effector. Taken together, these results suggest that a common control signal and a ballistic stage are recruited when coordinated eye-hand movement plans require alteration. PMID:26888104

Estimation of Coriolis Force and Torque Acting on Ares-1

NASA Technical Reports Server (NTRS)

Mackey, Ryan M.; Kulikov, Igor K.; Smelyanskiy, Vadim; Luchinsky, Dmitry; Orr, Jeb

2011-01-01

A document describes work on the origin of Coriolis force and estimating Coriolis force and torque applied to the Ares-1 vehicle during its ascent, based on an internal ballistics model for a multi-segmented solid rocket booster (SRB).

Durability Assessment of Various Gamma TiAl Alloys

NASA Technical Reports Server (NTRS)

Lerch, Brad; Draper, Sue; Pereira, Mike; Zhuang, Wyman

2003-01-01

Seven cast and one wrought gamma-alloys were ballistically impacted and tested under high cycle fatigue. The fatigue strength of each alloy was characterized as a function of initial flaw size and modeled using a threshold-based fracture mechanics approach.

Transition from normal to ballistic diffusion in a one-dimensional impact system

NASA Astrophysics Data System (ADS)

Livorati, André L. P.; Kroetz, Tiago; Dettmann, Carl P.; Caldas, Iberê L.; Leonel, Edson D.

2018-03-01

We characterize a transition from normal to ballistic diffusion in a bouncing ball dynamics. The system is composed of a particle, or an ensemble of noninteracting particles, experiencing elastic collisions with a heavy and periodically moving wall under the influence of a constant gravitational field. The dynamics lead to a mixed phase space where chaotic orbits have a free path to move along the velocity axis, presenting a normal diffusion behavior. Depending on the control parameter, one can observe the presence of featured resonances, known as accelerator modes, that lead to a ballistic growth of velocity. Through statistical and numerical analysis of the velocity of the particle, we are able to characterize a transition between the two regimes, where transport properties were used to characterize the scenario of the ballistic regime. Also, in an analysis of the probability of an orbit to reach an accelerator mode as a function of the velocity, we observe a competition between the normal and ballistic transport in the midrange velocity.

Injuries of the head from backface deformation of ballistic protective helmets under ballistic impact.

PubMed

Rafaels, Karin A; Cutcliffe, Hattie C; Salzar, Robert S; Davis, Martin; Boggess, Brian; Bush, Bryan; Harris, Robert; Rountree, Mark Steve; Sanderson, Ellory; Campman, Steven; Koch, Spencer; Dale Bass, Cameron R

2015-01-01

Modern ballistic helmets defeat penetrating bullets by energy transfer from the projectile to the helmet, producing helmet deformation. This deformation may cause severe injuries without completely perforating the helmet, termed "behind armor blunt trauma" (BABT). As helmets become lighter, the likelihood of larger helmet backface deformation under ballistic impact increases. To characterize the potential for BABT, seven postmortem human head/neck specimens wearing a ballistic protective helmet were exposed to nonperforating impact, using a 9 mm, full metal jacket, 124 grain bullet with velocities of 400-460 m/s. An increasing trend of injury severity was observed, ranging from simple linear fractures to combinations of linear and depressed fractures. Overall, the ability to identify skull fractures resulting from BABT can be used in forensic investigations. Our results demonstrate a high risk of skull fracture due to BABT and necessitate the prevention of BABT as a design factor in future generations of protective gear. © 2014 American Academy of Forensic Sciences.

Ballistic One-Dimensional InAs Nanowire Cross-Junction Interconnects.

PubMed

Gooth, Johannes; Borg, Mattias; Schmid, Heinz; Schaller, Vanessa; Wirths, Stephan; Moselund, Kirsten; Luisier, Mathieu; Karg, Siegfried; Riel, Heike

2017-04-12

Coherent interconnection of quantum bits remains an ongoing challenge in quantum information technology. Envisioned hardware to achieve this goal is based on semiconductor nanowire (NW) circuits, comprising individual NW devices that are linked through ballistic interconnects. However, maintaining the sensitive ballistic conduction and confinement conditions across NW intersections is a nontrivial problem. Here, we go beyond the characterization of a single NW device and demonstrate ballistic one-dimensional (1D) quantum transport in InAs NW cross-junctions, monolithically integrated on Si. Characteristic 1D conductance plateaus are resolved in field-effect measurements across up to four NW-junctions in series. The 1D ballistic transport and sub-band splitting is preserved for both crossing-directions. We show that the 1D modes of a single injection terminal can be distributed into multiple NW branches. We believe that NW cross-junctions are well-suited as cross-directional communication links for the reliable transfer of quantum information as required for quantum computational systems.

Transition from normal to ballistic diffusion in a one-dimensional impact system.

PubMed

Livorati, André L P; Kroetz, Tiago; Dettmann, Carl P; Caldas, Iberê L; Leonel, Edson D

2018-03-01

We characterize a transition from normal to ballistic diffusion in a bouncing ball dynamics. The system is composed of a particle, or an ensemble of noninteracting particles, experiencing elastic collisions with a heavy and periodically moving wall under the influence of a constant gravitational field. The dynamics lead to a mixed phase space where chaotic orbits have a free path to move along the velocity axis, presenting a normal diffusion behavior. Depending on the control parameter, one can observe the presence of featured resonances, known as accelerator modes, that lead to a ballistic growth of velocity. Through statistical and numerical analysis of the velocity of the particle, we are able to characterize a transition between the two regimes, where transport properties were used to characterize the scenario of the ballistic regime. Also, in an analysis of the probability of an orbit to reach an accelerator mode as a function of the velocity, we observe a competition between the normal and ballistic transport in the midrange velocity.

A Ballistics Examination of Firearm Injuries Involving Breast Implants.

PubMed

Pannucci, Christopher J; Cyr, Adam J; Moores, Neal G; Young, Jason B; Szegedi, Martin

2018-03-01

This ballistics study examines whether saline breast implants can decrease tissue penetration in firearm injuries. We hypothesize that the fluid column within a saline breast implant can alter bullet velocity and/or bullet pattern of mushrooming. The two experimental groups included saline implants with 7.4 cm projection and a no implant group. The experimental design allowed the bullet to pass-through an implant and into ballistics gel (n = 10) or into ballistics gel without passage through an implant (n = 11). Shots that passed through an implant had 20.6% decreased penetration distance when compared to shots that did not pass-through an implant; this difference was statistically significant (31.9 cm vs. 40.2 cm, p < 0.001). Implant group bullets mushroomed prior to gel entry, but the no implant group mushroomed within the gel. Bullet passage through a saline breast implant results in direct bullet velocity reduction and earlier bullet mushrooming; this causes significantly decreased ballistics gel penetration. © 2017 American Academy of Forensic Sciences.

Magneto-ballistic transport in GaN nanowires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santoruvo, Giovanni, E-mail: giovanni.santoruvo@epfl.ch; Allain, Adrien; Ovchinnikov, Dmitry

2016-09-05

The ballistic filtering property of nanoscale crosses was used to investigate the effect of perpendicular magnetic fields on the ballistic transport of electrons on wide band-gap GaN heterostructures. The straight scattering-less trajectory of electrons was modified by a perpendicular magnetic field which produced a strong non-linear behavior in the measured output voltage of the ballistic filters and allowed the observation of semi-classical and quantum effects, such as quenching of the Hall resistance and manifestation of the last plateau, in excellent agreement with the theoretical predictions. A large measured phase coherence length of 190 nm allowed the observation of universal quantum fluctuationsmore » and weak localization of electrons due to quantum interference up to ∼25 K. This work also reveals the prospect of wide band-gap GaN semiconductors as a platform for basic transport and quantum studies, whose properties allow the investigation of ballistic transport and quantum phenomena at much larger voltages and temperatures than in other semiconductors.« less

Fabry-Perot magnonic ballistic coherent transport across ultrathin ferromagnetic lamellar bcc Ni nanostructures between Fe leads

NASA Astrophysics Data System (ADS)

Khater, A.; Saim, L.; Tigrine, R.; Ghader, D.

2018-06-01

We propose thermodynamically stable systems of ultrathin lamellar bcc Ni nanostructures between bcc Fe leads, sbnd Fe[Ni(n)]Fesbnd , based on the available literature for bcc Ni overlayers on Fe(001) surfaces, and establish the necessary criteria for their structural and ferromagnetic order, for thicknesses n ≤ 6 bcc Ni monatomic layers. The system is globally ferromagnetic. A theoretical model is presented to investigate and understand the ballistic coherent scattering of Fe spin-waves, incident from the leads, at the ferromagnetic bcc Ni nanostructure. The Nisbnd Ni and Nisbnd Fe exchange are computed using the Ising effective field theory (EFT), and the magnetic ground state of the system is constructed in the Heisenberg representation. We compute the spin-wave eigenmodes localized on the bcc Ni nanostructure, using the phase field matching theory (PFMT), illustrating the effects of symmetry breaking on the confinement of localized spin excitations. The reflection and transmission scattering properties of spin-waves incident from the Fe leads, across the embedded Ni nanostructures are investigated within the framework of the same PFMT methodology. A highly refined Fabry-Perot magnonic ballistic coherent transmission spectra is observed for these sbnd Fe[Ni(n)]Fesbnd systems.

Quasi-ballistic Electronic Thermal Conduction in Metal Inverse Opals.

PubMed

Barako, Michael T; Sood, Aditya; Zhang, Chi; Wang, Junjie; Kodama, Takashi; Asheghi, Mehdi; Zheng, Xiaolin; Braun, Paul V; Goodson, Kenneth E

2016-04-13

Porous metals are used in interfacial transport applications that leverage the combination of electrical and/or thermal conductivity and the large available surface area. As nanomaterials push toward smaller pore sizes to increase the total surface area and reduce diffusion length scales, electron conduction within the metal scaffold becomes suppressed due to increased surface scattering. Here we observe the transition from diffusive to quasi-ballistic thermal conduction using metal inverse opals (IOs), which are metal films that contain a periodic arrangement of interconnected spherical pores. As the material dimensions are reduced from ∼230 nm to ∼23 nm, the thermal conductivity of copper IOs is reduced by more than 57% due to the increase in surface scattering. In contrast, nickel IOs exhibit diffusive-like conduction and have a constant thermal conductivity over this size regime. The quasi-ballistic nature of electron transport at these length scales is modeled considering the inverse opal geometry, surface scattering, and grain boundaries. Understanding the characteristics of electron conduction at the nanoscale is essential to minimizing the total resistance of porous metals for interfacial transport applications, such as the total electrical resistance of battery electrodes and the total thermal resistance of microscale heat exchangers.

Dimension dependence of clustering dynamics in models of ballistic aggregation and freely cooling granular gas

NASA Astrophysics Data System (ADS)

Paul, Subhajit; Das, Subir K.

2018-03-01

Via event-driven molecular dynamics simulations we study kinetics of clustering in assemblies of inelastic particles in various space dimensions. We consider two models, viz., the ballistic aggregation model (BAM) and the freely cooling granular gas model (GGM), for each of which we quantify the time dependence of kinetic energy and average mass of clusters (that form due to inelastic collisions). These quantities, for both the models, exhibit power-law behavior, at least in the long time limit. For the BAM, corresponding exponents exhibit strong dimension dependence and follow a hyperscaling relation. In addition, in the high packing fraction limit the behavior of these quantities become consistent with a scaling theory that predicts an inverse relation between energy and mass. On the other hand, in the case of the GGM we do not find any evidence for such a picture. In this case, even though the energy decay, irrespective of packing fraction, matches quantitatively with that for the high packing fraction picture of the BAM, it is inversely proportional to the growth of mass only in one dimension, and the growth appears to be rather insensitive to the choice of the dimension, unlike the BAM.

External Ballistics. Part 1

DTIC Science & Technology

1978-07-11

trajectories and aEe gAven the concepts cf tke oEtiaua sclticas of the problems of e.termal ballistics. Is estimated the effect c different perturkation... development receimed the d*signed kallistic calculaticns ct scattering trajectoies bith the firiqg icckets and artillery shells. The application/use of...problems, solved in the course of external ballistics, they at* bscught informaticn fzca the histccl of the development of the thecrj of flight and

Investigation of Basalt Woven Fabrics for Military Applications

DTIC Science & Technology

2011-11-01

investigates the use of basalt fibers in a composite along with SC-15 epoxy resin for ballistic protection. Basalt fibers are not known as a ballistic...material but rather as a structural one. Even though basalt fibers are not expected to outperform some of the higher ballistic performing materials...such as the aramid and polyethylene fibers ; however, due to the lower manufacturing costs, basalt fibers are an interesting alternative. The objective

Obscuration Due to Dust of a Laser Beam in a Gun Firing Environment - Preliminary Survey

DTIC Science & Technology

1975-10-01

34 APG- MT-4371, Nov 1973, Aberdeen Proving Ground , MD (AD Number: 915796L). 13. Engineering Design Handbook, Ballistic Series, "Interior Ballistics of...Technical Library Watervliet, NY 12189 Director Ballistic Research Laboratories Aberdeen Proving Ground , MD 21005 Commander US Army Electronics...RHFL Warren, MI 48090 Commander Aberdeen Proving Ground ATTN: Tech Lib., Bldg 313 Aberdeen Proving Ground , MD 22005 Chief of Naval Research

Steering and collimating ballistic electrons with amphoteric refraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Radu, A.; Dragoman, D.; Iftimie, S.

2012-07-15

We show that amphoteric refraction of ballistic electrons, i.e., positive or negative refraction depending on the incidence angle, occurs at an interface between an isotropic and an anisotropic medium and can be employed to steer and collimate electron beams. The steering angle is determined by the materials' parameters, but the degree of collimation can be tuned in a significant range by changing the energy of ballistic electrons.

Bio-inspired Armor Protective Material Systems for Ballistic Shock Mitigation

DTIC Science & Technology

2011-01-01

Coupon testing a b s t r a c t Severe transient ballistic shocks from projectile impacts, mine blasts , or overhead artillery attacks can incapacitate an...past two decades [1]. A ballistic shock results from a significant amount of concentrated energy deposited from caliber projectile impacts, mine blasts ...LS- Dyna , has been predominately utilized to calculate the target shock responses including acceleration histo- ries, shock response spectra

Are certain fractures at increased risk for compartment syndrome after civilian ballistic injury?

PubMed

Meskey, Thomas; Hardcastle, John; O'Toole, Robert V

2011-11-01

Compartment syndrome after ballistic fracture is uncommon but potentially devastating. Few data are available to help guide clinicians regarding risk factors for developing compartment syndrome after ballistic fractures. Our primary hypothesis was that ballistic fractures of certain bones would be at higher risk for development of compartment syndrome. A retrospective review at a Level I trauma center from 2001 through 2007 yielded 650 patients with 938 fractures resulting from gunshots. We reviewed all operative notes, clinic notes, discharge summaries, and data from our prospective trauma database. Cases in which the attending orthopedic surgeon diagnosed compartment syndrome and performed fasciotomy were considered cases with compartment syndrome. We excluded all prophylactic fasciotomies. Univariate analyses were conducted to identify risk factors associated with development of compartment syndrome. Twenty-six (2.8%) of the 938 fractures were associated with compartment syndrome. Only fibular (11.6%) and tibial (11.4%) fractures had incidence significantly higher than baseline for all ballistic fractures (p < 0.001). Fractures of the proximal third of the fibula were more likely to result in compartment syndrome than fractures of the middle or distal third (p = 0.03), as were fractures of the proximal third of the tibia (p = 0.01). No other demographic or injury parameters were associated with compartment syndrome. Ballistic fractures of the fibula and tibia are at increased risk for development of compartment syndrome over other ballistic fractures. We recommend increased vigilance when treating these injuries, particularly if the fracture is in the proximal aspect of the bone or is associated with vascular injury.

Cost of space-based laser ballistic missile defense.

PubMed

Field, G; Spergel, D

1986-03-21

Orbiting platforms carrying infrared lasers have been proposed as weapons forming the first tier of a ballistic missile defense system under the President's Strategic Defense Initiative. As each laser platform can destroy a limited number of missiles, one of several methods of countering such a system is to increase the number of offensive missiles. Hence it is important to know whether the cost-exchange ratio, defined as the ratio of the cost to the defense of destroying a missile to the cost to the offense of deploying an additional missile, is greater or less than 1. Although the technology to be used in a ballistic missile defense system is still extremely uncertain, it is useful to examine methods for calculating the cost-exchange ratio. As an example, the cost of an orbiting infrared laser ballistic missile defense system employed against intercontinental ballistic missiles launched simultaneously from a small area is compared to the cost of additional offensive missiles. If one adopts lower limits to the costs for the defense and upper limits to the costs for the offense, the cost-exchange ratio comes out substantially greater than 1. If these estimates are confirmed, such a ballistic missile defense system would be unable to maintain its effectiveness at less cost than it would take to proliferate the ballistic missiles necessary to overcome it and would therefore not satisfy the President's requirements for an effective strategic defense. Although the method is illustrated by applying it to a space-based infrared laser system, it should be straightforward to apply it to other proposed systems.

Cost of space-based laser ballistic missile defense

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, G.; Spergel, D.

1986-03-21

Orbiting platforms carrying infrared lasers have been proposed as weapons forming the first tier of a ballistic missile defense system under the President's Strategic Defense Initiative. As each laser platform can destroy a limited number of missiles, one of several methods of countering such a system is to increase the number of offensive missiles. Hence it is important to know whether the cost-exchange ratio, defined as the ratio of the cost to the defense of destroying a missile to the cost to the offense of deploying an additional missile, is greater or less than 1. Although the technology to bemore » used in a ballistic missile defense system is still extremely uncertain, it is useful to examine methods for calculating the cost-exchange ration. As an example, the cost of an orbiting infrared laser ballistic missile defense system employed against intercontinental ballistic missiles launched simultaneously from a small area is compared to the cost of additional offensive missiles. If one adopts lower limits to the costs for the defense and upper limits to the costs for the offense, the cost-exchange ratio comes out substantially greater than 1. If these estimates are confirmed, such a ballistic missile defense system would be unable to maintain its effectiveness at less cost than it would take to proliferate the ballistic missiles necessary to overcome it and would therefore not satisfy the President's requirements for an effective strategic defense. Although the method is illustrated by applying it to a space-based infrared laser system, it should be straightforward to apply it to other proposed systems. 28 references, 2 tables.« less

Projectile Impact Evaluation on Ballistic Gelatin

DTIC Science & Technology

2011-06-13

g en ormu a on w near u mo u us Impact modeling • Damage model [DuBois, Kolling, LSTC] Methods – Gelatin Calibration • Calibration (10%/4°C...FE (LS-Dyna v971) w/ LSOPT • High strain rate material properties w/ damage/failure L i ALE EFG f l ti Loading [Impact] • agrang an, , ormu a ons

Modeling Ballistic Response of Ultra-High-Molecular-Weight Polyethylene (UHMWPE)

DTIC Science & Technology

2016-07-01

posttest panels. Fig. 5 Variables to be compared between model and experiments The 6 tests and available test data are listed in Table 2. The first 3...Time history of center BFD for the 3 BFD tests Figure 24 shows the damages in the panels from posttest CT scan of the UHMWPE panels and the

A Ballistic Model of Choice Response Time

ERIC Educational Resources Information Center

Brown, Scott; Heathcote, Andrew

2005-01-01

Almost all models of response time (RT) use a stochastic accumulation process. To account for the benchmark RT phenomena, researchers have found it necessary to include between-trial variability in the starting point and/or the rate of accumulation, both in linear (R. Ratcliff & J. N. Rouder, 1998) and nonlinear (M. Usher & J. L. McClelland, 2001)…

Modeling and Simulation of Ceramic Arrays to Improve Ballistic Performance

DTIC Science & Technology

2014-01-17

30cal AP M2 Projectile, 762x39 PS Projectile, SPH , Aluminum 5083, SiC, DoP Expeminets, AutoDyn Simulations, Tile Gap 16. SECURITY CLASSIFICATION...particle hydrodynamics ( SPH ) is applied for all parts. The SPH particle size is .4 mm, with the assumption that modeling dust smaller than .4 mm can be

Multi-Length Scale-Enriched Continuum-Level Material Model for Kevlar-Fiber-Reinforced Polymer-Matrix Composites

DTIC Science & Technology

2012-08-03

is unlimited. Multi-Length Scale-Enriched Continuum-Level Material Model for Kevlar ®-Fiber-Reinforced Polymer-Matrix Composites The views, opinions...12211 Research Triangle Park, NC 27709-2211 ballistics, composites, Kevlar , material models, microstructural defects REPORT DOCUMENTATION PAGE 11... Kevlar ®-Fiber-Reinforced Polymer-Matrix Composites Report Title Fiber-reinforced polymer matrix composite materials display quite complex deformation

Acute Effects of Static vs. Ballistic Stretching on Strength and Muscular Fatigue Between Ballet Dancers and Resistance-Trained Women.

PubMed

Lima, Camila D; Brown, Lee E; Wong, Megan A; Leyva, Whitney D; Pinto, Ronei S; Cadore, Eduardo L; Ruas, Cassio V

2016-11-01

Lima, CD, Brown, LE, Wong, MA, Leyva, WD, Pinto, RS, Cadore, EL, and Ruas, CV. Acute effects of static vs. ballistic stretching on strength and muscular fatigue between ballet dancers and resistance-trained women. J Strength Cond Res 30(11): 3220-3227, 2016-Stretching is used to increase joint range of motion, but the acute effects can decrease muscle strength. However, this may depend on the population or mode of stretching. The purpose of this study was to compare the acute effects of static vs. ballistic stretching on strength and muscular fatigue between ballet dancers and resistance-trained women. Fifteen resistance-trained women (age 23.8 ± 1.80 years, mass 67.47 ± 7.77 kg, height 168.30 ± 5.53 cm) and 12 ballet dancers (age 22.8 ± 3.04 years, mass 58.67 ± 5.65 kg, height 168.00 ± 7.69 cm) performed 5 days of testing. The first day was control (no stretching), whereas the other 4 days were static or ballistic stretching in a counterbalanced order. Range of motion, strength, and fatigue tests were also performed. Both groups demonstrated a significant decrease in hamstrings strength after static (102.71 ± 2.67 N·m) and ballistic stretching (99.49 ± 2.61 N·m) compared with control (113.059 ± 3.25 N·m), with no changes in quadriceps strength. For fatigue, only ballet dancers demonstrated a decrease from control (71.79 ± 4.88%) to ballistic (65.65 ± 8.19%), but no difference with static (65.01 ± 12.29%). These findings suggest that stretching decreases hamstrings strength similarly in ballet dancers and resistance-trained women, with no differences between modes of stretching. However, ballistic stretching only decreased muscular fatigue in ballet dancers, but not in resistance-trained women. Therefore, no stretching should be performed before strength performance. However, ballistic stretching may decrease acute muscular fatigue in ballet dancers.

Self-Consistent Theory of Shot Noise Suppression in Ballistic Conductors

NASA Astrophysics Data System (ADS)

Bulashenko, O. M.; Rubí, J. M.; Kochelap, V. A.

Shot-noise measurements become a fundamental tool to probe carrier interactions in mesoscopic systems [1]. A matter of particular interest is the significance of Coulomb interaction which may keep nearby electrons more regularly spaced rather than strictly at random and lead to the noise reduction. That effect occurs in different physical situations. Among them are charge-limited ballistic transport, resonant tunneling, single-electron tunneling, etc. In this communication we address the problem of Coulomb correlations in ballistic conductors under the space-charge-limited transport conditions, and present for the first time a semiclassical self-consistent theory of shot noise in these conductors by solving analytically the kinetic equation coupled self-consistently with a Poisson equation. Basing upon this theory, exact results for current noise in a two-terminal ballistic conductor under the action of long-range Coulomb correlations has been derived. The noise reduction factor (in respect to the uncorrelated value) is obtained in a closed analytical form for a full range of biases ranging from thermal to shot-noise limits which describe perfectly the results of the Monte Carlo simulations for a nondegenerate electron gas [2]. The magnitude of the noise reduction exceeds 0.01, which is of interest from the point of view of possible applications. Using these analytical results one may estimate a relative contribution to the noise from different groups of carriers (in energy space and/or real space) and to investigate in great detail the correlations between different groups of carriers. This leads us to suggest an electron energy spectroscopy experiment to probe the Coulomb correlations in ballistic conductors. Indeed, while the injected carriers are uncorrelated, those in the volume of the conductor are strongly correlated, as follows from the derived formulas for the fluctuation of the distribution function. Those correlations may be observed experimentally by making use of a combination of two already realized techniques: a hot-electron spectrometer [3,4] which allows one to analyze different energy groups of electrons collected at the contact and shot-noise measurements [5,6]. Such "shot noise reduction spectroscopy" allows one to measure the novel phenomena. In particular, we predict the (anti)correlation of the "tangent" electrons having the energy close to the potential barrier height, to all other electron energy groups collected at the receiving contact.

Flight motor set 360L007 (STS-33R)

NASA Technical Reports Server (NTRS)

Garecht, Diane

1990-01-01

Flight motor set 360L007 was launched as part of NASA space shuttle mission STS-33R. As with all previous redesigned solid rocket motor launches, overall motor performance was excellent. There were no debris concerns for either motor. Both motors exhibited unbonds on one factory joint weatherseal. All ballistics contract end item specification parameters were verified, with the exception of ignition interval and rise rates. Ignition interval and rise rates could not be verified due to the elimination of developmental flight instrumentation from fourth flight and subsequent, but the low sample rate data that were available showed nominal propulsion performance. All ballistic and mass property parameters closely matched the predicted values and were well within the required contract end item specification levels that could be assessed. All 108 Ground Environment Instrumentation (GEI) measurements performed properly throughout the prelaunch phase. Evaluation of the GEI measurements again verified thermal model analysis data and showed agreement with predicted environmental effects. No launch commit criteria thermal violations occurred. All joint heaters operated normally, but a high voltage reading was noted on the left hand aft heater, which was immediately determined to be a voltage sensor error and not a heater anomaly due to no current increase. Postflight inspection again verified superior performance of the insulation, phenolics, metal parts, and seals. Postflight evaluation indicated both nozzles performed as expected during flight. All combustion gas was contained by insulation in the field and case-to-nozzle joints.

Measurement strategy and analytic model to determine firing pin force

NASA Astrophysics Data System (ADS)

Lesenciuc, Ioan; Suciu, Cornel

2016-12-01

As illustrated in literature, ballistics is a branch of theoretical mechanics, which studies the construction and working principles of firearms and ammunition, their effects, as well as the motions of projectiles and bullets1. Criminalistics identification, as part of judiciary identification represents an activity aimed at finding common traits of different objects, objectives, phenomena and beings, but more importantly, traits that differentiate each of them from similar ones2-4. In judicial ballistics, in the case of rifled firearms it is relatively simple for experts to identify the used weapon from traces left on the projectile, as the rifling of the barrel leaves imprints on the bullet, which remain approximately identical even after the respective weapon is fired 100 times with the same barrel. However, in the case of smoothbore firearms, their identification becomes much more complicated. As the firing cap suffers alterations from being hit by the firing pin, determination of the force generated during impact creates the premises for determining the type of firearm used to shoot the respective cartridge. The present paper proposes a simple impact model that can be used to evaluate the force generated by the firing pin during its impact with the firing cap. The present research clearly showed that each rifle, by the combination of the three investigated parameters (impact force maximum value, its variation diagram, and impact time) leave a unique trace. Application of such a method in ballistics can create the perspectives for formulating clear conclusions that eliminate possible judicial errors in this field.

Photogrammetry and ballistic analysis of a high-flying projectile in the STS-124 space shuttle launch

NASA Astrophysics Data System (ADS)

Metzger, Philip T.; Lane, John E.; Carilli, Robert A.; Long, Jason M.; Shawn, Kathy L.

2010-07-01

A method combining photogrammetry with ballistic analysis is demonstrated to identify flying debris in a rocket launch environment. Debris traveling near the STS-124 Space Shuttle was captured on cameras viewing the launch pad within the first few seconds after launch. One particular piece of debris caught the attention of investigators studying the release of flame trench fire bricks because its high trajectory could indicate a flight risk to the Space Shuttle. Digitized images from two pad perimeter high-speed 16-mm film cameras were processed using photogrammetry software based on a multi-parameter optimization technique. Reference points in the image were found from 3D CAD models of the launch pad and from surveyed points on the pad. The three-dimensional reference points were matched to the equivalent two-dimensional camera projections by optimizing the camera model parameters using a gradient search optimization technique. Using this method of solving the triangulation problem, the xyz position of the object's path relative to the reference point coordinate system was found for every set of synchronized images. This trajectory was then compared to a predicted trajectory while performing regression analysis on the ballistic coefficient and other parameters. This identified, with a high degree of confidence, the object's material density and thus its probable origin within the launch pad environment. Future extensions of this methodology may make it possible to diagnose the underlying causes of debris-releasing events in near-real time, thus improving flight safety.

Optimal Estimation with Two Process Models and No Measurements

DTIC Science & Technology

2015-08-01

models will be lost if either of the models includes deterministic modeling errors. 12 5. References and Notes 1. Brown RG, Hwang PYC. Introduction to...independent process models when no measurements are present. The observer follows a derivation similar to that of the discrete time Kalman filter. A simulation...discrete time Kalman filter. A simulation example is provided in which a process model based on the dynamics of a ballistic projectile is blended with an

Pyrotechnic Shock Analysis Using Statistical Energy Analysis

DTIC Science & Technology

2015-10-23

SEA subsystems. A couple of validation examples are provided to demonstrate the new approach. KEY WORDS : Peak Ratio, phase perturbation...Ballistic Shock Prediction Models and Techniques for Use in the Crusader Combat Vehicle Program,” 11th Annual US Army Ground Vehicle Survivability

An Introduction to the Sources of Delivery Error for Direct-Fire Ballistic Projectiles

DTIC Science & Technology

2013-07-01

Ballistic mismatch has also been used to quantify the difference in target impacts using different gun tubes ...the angle between the local “upwards” direction of the gun tube and the vertical direction as defined by gravity. Cant results from the gun tube ...Determining Optimal Tube Shape for Reduction of Jump Error for Tank Fleets Using Fleet Zero. Presented at the 20th International Symposium on Ballistics

Aircraft Pilot Situational Awareness Interface for Airborne Operation of Network Controlled Unmanned Systems (US)

DTIC Science & Technology

2008-03-01

operator, can be operated autonomously or remotely, can be expendable or recoverable, and can carry a lethal or nonlethal payload. Ballistic or semi ...states that vehicles should be recoverable, and that ballistic or semi - ballistic vehicles, cruise missiles, and artillery projectiles are not considered...2007-2032. 32 Nicola Tesla and his telautomatons (robots); Tesla further demonstrated remote control of objects by wireless in an exhibition in 1898

Friction Stir Weld Failure Mechanisms in Aluminum-Armor Structures Under Ballistic Impact Loading Conditions

DTIC Science & Technology

2013-01-01

REPORT Friction Stir Weld Failure Mechanisms in Aluminum -Armor Structures Under Ballistic Impact Loading Conditions 14. ABSTRACT 16. SECURITY...Stir Weld Failure Mechanisms in Aluminum -Armor Structures Under Ballistic Impact Loading Conditions M. Grujicic, B. Pandurangan, A. Arakere, C-F. Yen...K.O. Pedersen, Fracture Mechanisms of Aluminum Alloy AA7075-T651 Under Various Loading Conditions , Int. J. Impact Eng., 2010, 37, p 537–551 24. T

Detection technique of targets for missile defense system

NASA Astrophysics Data System (ADS)

Guo, Hua-ling; Deng, Jia-hao; Cai, Ke-rong

2009-11-01

Ballistic missile defense system (BMDS) is a weapon system for intercepting enemy ballistic missiles. It includes ballistic-missile warning system, target discrimination system, anti-ballistic-missile guidance systems, and command-control communication system. Infrared imaging detection and laser imaging detection are widely used in BMDS for surveillance, target detection, target tracking, and target discrimination. Based on a comprehensive review of the application of target-detection techniques in the missile defense system, including infrared focal plane arrays (IRFPA), ground-based radar detection technology, 3-dimensional imaging laser radar with a photon counting avalanche photodiode (APD) arrays and microchip laser, this paper focuses on the infrared and laser imaging detection techniques in missile defense system, as well as the trends for their future development.

Higher-than-ballistic conduction of viscous electron flows

PubMed Central

Guo, Haoyu; Ilseven, Ekin; Falkovich, Gregory; Levitov, Leonid S.

2017-01-01

Strongly interacting electrons can move in a neatly coordinated way, reminiscent of the movement of viscous fluids. Here, we show that in viscous flows, interactions facilitate transport, allowing conductance to exceed the fundamental Landauer’s ballistic limit Gball. The effect is particularly striking for the flow through a viscous point contact, a constriction exhibiting the quantum mechanical ballistic transport at T=0 but governed by electron hydrodynamics at elevated temperatures. We develop a theory of the ballistic-to-viscous crossover using an approach based on quasi-hydrodynamic variables. Conductance is found to obey an additive relation G=Gball+Gvis, where the viscous contribution Gvis dominates over Gball in the hydrodynamic limit. The superballistic, low-dissipation transport is a generic feature of viscous electronics. PMID:28265079

A safe model for creating blunt and penetrating ballistic injury.

PubMed

Graeber, G M; Belville, W D; Sepulveda, R A

1981-06-01

Minor modification of an existing readily available captive projectile weapon system has allowed development of a safe model for studying both penetrating ballistic and blunt tissue injury. A captive projectile weapon (defined as a firearm in which the projectile does not leave the weapon and in which the external wounding range is very limited) diminishes greatly the possibility of injury to personnel while it allows a high degree of reproducibility. The system has three parts: the pistol (wt 1.3 kg), a stainless steel stand, and a rack for holding the organ to be injured. It has been used 14 times in developing a canine model for the study of penetrating ballistic renal injury. When a 2 grain, .22 caliber charge is fired in the weapon, the .45 caliber captive projectile travels 7.5 cm and penetrates the kidney completely. The kinetic energy available for transfer from the projectile to the kidney and renal vessels totals 211 joules, which is comparable to the kinetic energy of projectiles for many law enforcement sidearms at 45.72 meters (50 yards) from the muzzle of the weapon. Comparison of the wounds showed complete reproducibility of injury (100%) over all 14 subjects [Entrance wound greater than or equal to .45 caliber (100%). Exit wound greater than or equal to .45 caliber (100%). Complete penetration (100%)]. This weapon system can be modified to duplicate the injury created by missiles from many small arms by modifying the captive projectile and/or the charge. Changing the leading surface of the captive projectile allows delivery of the energy over a broad surface such that blunt injuries can be simulated.

Geometrical and Kinematic Parameters of the Jet of the Blazar S5 0716+71 in a Helical-Jet Model

NASA Astrophysics Data System (ADS)

Butuzova, M. S.

2018-02-01

Periodic variations of the position angle of the inner jet of the blazar S5 0716+71 suggest a helical structure for the jet. The geometrical parameters of a model helical jet are determined. It is shown that, when the trajectories of the jet components are non-ballistic, the angle between their velocity vectors and the line of sight lies in a broader interval than is the case for ballistic motions of the components, in agreement with available estimates. The contradictory results for the apparent speeds of components in the inner and outer jet at epochs 2004 and 2008-2010 can be explained in such a model. The ratio of the apparent speeds in the inner and outer jet are used to derive a lower limit for the physical speed of the components ( β > 0.999) and to determine the pitch angle of the helical jet ( p = 5.5°). The derived parameters can give rise to the conditions required to observe high speeds (right to 37 c) for individual jet components.

Rashba quantum wire: exact solution and ballistic transport.

PubMed

Perroni, C A; Bercioux, D; Ramaglia, V Marigliano; Cataudella, V

2007-05-08

The effect of Rashba spin-orbit interaction in quantum wires with hard-wall boundaries is discussed. The exact wavefunction and eigenvalue equation are worked out, pointing out the mixing between the spin and spatial parts. The spectral properties are also studied within perturbation theory with respect to the strength of the spin-orbit interaction and diagonalization procedure. A comparison is made with the results of a simple model, the two-band model, that takes account only of the first two sub-bands of the wire. Finally, the transport properties within the ballistic regime are analytically calculated for the two-band model and through a tight-binding Green function for the entire system. Single and double interfaces separating regions with different strengths of spin-orbit interaction are analysed by injecting carriers into the first and the second sub-band. It is shown that in the case of a single interface the spin polarization in the Rashba region is different from zero, and in the case of two interfaces the spin polarization shows oscillations due to spin-selective bound states.

Compositional Evolution of Saturn's Ring: Ice, Tholin, and 'CHIRON'-Dust

NASA Technical Reports Server (NTRS)

Cuzzi, Jeffrey N.; Estrada, P. R.; DeVincenzi, Donald L. (Technical Monitor)

1996-01-01

We address compositional evolution in planetary ring systems subsequent to meteoroid bombardment. The huge surface area to mass ratio of planetary rings ensures the importance of this process, given currently expected values of meteoroid flux. We developed a model which includes both direct deposition of extrinsic meteoritic 'pollutants', and ballistic transport of the increasingly polluted ring material as impact ejecta. Certain aspects of the observed regional variations in ring color and albedo can be understood in terms of such a process. We conclude that the regional scale color and albedo differences between the C ring and B ring can be understood if all ring material began with the same composition (primarily water ice, based on other data, but colored by tiny amounts of non-icy, reddish absorber) and then evolved entirely by addition and mixing of extrinsic, neutrally colored, highly absorbing material. This conclusion is readily extended to the Cassini Division and its surroundings as well. Typical silicates are unable to satisfy the ring color, spectroscopic, and microwave absorption constraints either as intrinsic or extrinsic non-icy constituents. However, 'Titan Tholin' provides a satisfactory match for the inferred refractive indices of the 'pre-pollution' nonicy ring material. The extrinsic bombarding material is compatible with the properties of Halley or Chiron, but not with the properties of other 'red' primitive objects such as Pholus. We further demonstrate that the detailed radial profile of color across the abrupt B ring - C ring boundary is quite compatible with such a 'pollution transport' process, and that the shape of the profile can constrain key parameters in the model. We use the model to estimate the 'exposure age' of Saturn's rings to extrinsic meteoroid flux. We obtain a geologically young 'age' which is compatible with timescales estimated independently based on the evolution of ring structure due to ballistic transport, and also with other 'short timescales' estimated on the grounds of gravitational torques.

Seismic anisotropy in the Earth's innermost inner core: Testing structural models against mineral physics predictions

DOE PAGES

Romanowicz, Barbara; Cao, Aimin; Godwal, Budhiram; ...

2016-01-06

Using an updated data set of ballistic PKIKP travel time data at antipodal distances, we test different models of anisotropy in the Earth's innermost inner core (IMIC) and obtain significantly better fits for a fast axis aligned with Earth's rotation axis, rather than a quasi-equatorial direction, as proposed recently. Reviewing recent results on the single crystal structure and elasticity of iron at core conditions, we find that an hcp structure with the fast c axis parallel to Earth's rotation is more likely but a body-centered cubic structure with the [111] axis aligned in that direction results in very similar predictionsmore » for seismic anisotropy. These models are therefore not distinguishable based on current seismological data. In addition, to match the seismological observations, the inferred strength of anisotropy in the IMIC (6–7%) implies almost perfect alignment of iron crystals, an intriguing, albeit unlikely situation, especially in the presence of heterogeneity, which calls for further studies. Fast axis of anisotropy in the central part of the inner core aligned with Earth's axis of rotation Lastly, the structure of iron in the inner core is most likely hcp, not bcc Not currently possible to distinguish between hcp and bcc structures from seismic observations« less

Electronic Noise and Fluctuations in Solids

NASA Astrophysics Data System (ADS)

Kogan, Sh.

2008-07-01

Preface; Part I. Introduction. Some Basic Concepts of the Theory of Random Processes: 1. Probability density functions. Moments. Stationary processes; 2. Correlation function; 3. Spectral density of noise; 4. Ergodicity and nonergodicity of random processes; 5. Random pulses and shot noise; 6. Markov processes. General theory; 7. Discrete Markov processes. Random telegraph noise; 8. Quasicontinuous (Diffusion-like) Markov processes; 9. Brownian motion; 10. Langevin approach to the kinetics of fluctuations; Part II. Fluctuation-Dissipation Relations in Equilibrium Systems: 11. Derivation of fluctuation-dissipation relations; 12. Equilibrium noise in quasistationary circuits. Nyquist theorem; 13. Fluctuations of electromagnetic fields in continuous media; Part III. Fluctuations in Nonequilibrium Gases: 14. Some basic concepts of hot-electrons' physics; 15. Simple model of current fluctuations in a semiconductor with hot electrons; 16. General kinetic theory of quasiclassical fluctuations in a gas of particles. The Boltzmann-Langevin equation; 17. Current fluctuations and noise temperature; 18. Current fluctuations and diffusion in a gas of hot electrons; 19. One-time correlation in nonequilibrium gases; 20. Intervalley noise in multivalley semiconductors; 21. Noise of hot electrons emitting optical phonons in the streaming regime; 22. Noise in a semiconductor with a postbreakdown stable current filament; Part IV. Generation-recombination noise: 23. G-R noise in uniform unipolar semiconductors; 24. Noise produced by recombination and diffusion; Part V. Noise in quantum ballistic systems: 25. Introduction; 26. Equilibrium noise and shot noise in quantum conductors; 27. Modulation noise in quantum point contacts; 28. Transition from a ballistic conductor to a macroscopic one; 29. Noise in tunnel junctions; Part VI. Resistance noise in metals: 30. Incoherent scattering of electrons by mobile defects; 31. Effect of mobile scattering centers on the electron interference pattern; 32. Fluctuations of the number of diffusing scattering centers; 33. Temperature fluctuations and the corresponding noise; Part VII. Noise in strongly disordered conductors: 34. Basic ideas of the percolation theory; 35. Resistance fluctuations in percolation systems. 36. Experiments; Part VIII. Low-frequency noise with an 1/f-type spectrum and random telegraph noise: 37. Introduction; 38. Some general properties of 1/f noise; 39. Basic models of 1/f noise; 40./f noise in metals; 41. Low-frequency noise in semiconductors; 42. Magnetic noise in spin glasses and some other magnetic systems; 43. Temperature fluctuations as a possible source of 1/f noise; 44. Random telegraph noise; 45. Fluctuations with 1/f spectrum in other systems; 46. General conclusions on 1/f noise; Part IX. Noise in Superconductors and Superconducting Structures: 47. Noise in Josephson junctions; 48. Noise in type II superconductors; References; Subject index.

Terminal Performance of Lead Free Pistol Bullets in Ballistic Gelatin Using Retarding Force Analysis from High Speed Video

DTIC Science & Technology

2016-04-04

Terminal Performance of Lead-Free Pistol Bullets in Ballistic Gelatin Using Retarding Force Analysis from High Speed Video ELIJAH COURTNEY, AMY...quantified using high speed video . The temporary stretch cavities and permanent wound cavities are also characterized. Two factors tend to re- duce the...Performance of Lead-Free Pistol Bullets in Ballistic Gelatin Using Retarding Force Analysis from High Speed Video cavity. In addition, stretching can also

Navy Ohio Replacement (SSBN[X]) Ballistic Missile Submarine Program: Background and Issues for Congress

DTIC Science & Technology

2016-04-05

Navy Ohio Replacement (SSBN[ X ]) Ballistic Missile Submarine Program: Background and Issues for Congress Ronald O’Rourke Specialist in Naval...Affairs April 5, 2016 Congressional Research Service 7-5700 www.crs.gov R41129 Navy Ohio Replacement (SSBN[ X ]) Ballistic Missile Submarine...as the SSBN( X ) program, as the Navy’s top priority program. The Navy wants to procure the first Ohio replacement boat in FY2021, and the $773.1

Self-Attractive Random Walks: The Case of Critical Drifts

NASA Astrophysics Data System (ADS)

Ioffe, Dmitry; Velenik, Yvan

2012-07-01

Self-attractive random walks (polymers) undergo a phase transition in terms of the applied drift (force): If the drift is strong enough, then the walk is ballistic, whereas in the case of small drifts self-attraction wins and the walk is sub-ballistic. We show that, in any dimension d ≥ 2, this transition is of first order. In fact, we prove that the walk is already ballistic at critical drifts, and establish the corresponding LLN and CLT.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Barton; Rajic, Slobodan; Hunter, Scott Robert

The objective of this work was to demonstrate that a superhydrophobic coating technology developed at Oak Ridge National Laboratory (ORNL) increases the water repellency of ballistic fabric beyond that provided by existing water repellency treatments. This increased water repellency has the potential to provide durable ballistic fabric for body armor without adding significant weight to the armor or significant manufacturing cost. Specimens of greige and scoured ballistic fabric were treated with a superhydrophobic coating and their weights and degree of water repellency were compared to specimens of untreated fabric. Treatment of both greige and scoured ballistic fabrics yielded highly watermore » repellent fabrics. Our measurements of the water droplet contact angles gave values of approximately 150 , near the lower limit of 160 for superhydrophobic surfaces. The coatings increased the fabric weights by approximately 6%, an amount that is many times less than the estimated weight increase in a conventional treatment of ballistic fabric. The treated fabrics retained a significant amount of water repellency following a basic abrasion test, with water droplet contact angles decreasing by 14 to 23 . Microscopic analysis of the coating applied to woven fabrics indicated that the coating adhered equally well to fibers of greige and scoured yarns. Future evaluation of the superhydrophobic water repellent treatment will involve the manufacture of shoot packs of treated fabric for ballistic testing and provide an analysis of manufacturing scale-up and cost-to-benefit considerations.« less

Higher-Than-Ballistic Conduction in Viscous Electron Fluids

NASA Astrophysics Data System (ADS)

Levitov, Leonid

Strongly interacting electrons can move in a neatly coordinated way, reminiscent of the movement of viscous fluids. This talk will argue that in viscous flows interactions facilitate transport, allowing conductance to exceed the fundamental Sharvin-Landauer quantum-ballistic limit. The effect is particularly striking for the flow through a viscous point contact, a constriction exhibiting the quantum-mechanical ballistic transport at T = 0 but governed by electron hydrodynamics at elevated temperatures. Conductance grows as a square of the constriction width, i.e. faster than the linear width dependence for noninteracting fermions. The crossover between the ballistic and viscous regimes occurs when the mean free path for e-e collisions becomes comparable to the constriction width. Further, we will discuss the negative nonlocal response, a signature effect of viscous transport. This response exhibits an interesting nonmonotonic behavior vs. T at the viscous-to-balistic transition. The response is negative but small in the highly viscous regime at elevated temperatures. The value grows as the temperature is lowered and the system becomes less viscous, reaching the most negative values in the crossover region where the mean free path is comparable to the distance between contacts. Subsequently, it reverses sign at even lower temperatures, becoming positive as the system enters the ballistic regime. This peculiar behavior provides a clear signature of the ballistic-to-viscous transition and enables a direct measurement of the electron-electron collision mean free path.